WorldWideScience

Sample records for radiosterilization process organization

  1. Requirements concerning radiosterilization process organization; Wymagania dotyczace organizacji procesu sterylizacji radiacyjnej

    Energy Technology Data Exchange (ETDEWEB)

    Kaluska, I [Institute of Nuclear Chemistry and Technology, Warsaw (Poland)

    1997-10-01

    Administrative procedure connecting for licensing new materials or consumer products appropriated to radiosterilization have been performed and explained. Also the organization of irradiation process for attaining the proper result have been described in detail. 4 refs, 1 tab.

  2. Radiosterilization process control in plants using electron accelerators

    International Nuclear Information System (INIS)

    Stuglik, Z.

    1997-01-01

    Electron beam parameters deciding the irradiation dose in radiosterilization plants should be continuously controlled during the process. Dosimetric procedure suitable to irradiated material and dose range should be chosen. The practical advice and directions in this subject have been done. 7 refs

  3. Radio-sterilization and processing of frozen human skin

    International Nuclear Information System (INIS)

    Zarate S, Herman; Aguirre H, Paulina; Silva R, Samy; Hitschfeld G, Mario

    2006-01-01

    The Laboratory of Radio-sterilized Biological Tissues Processing (LPTR) belonging to the Chilean Commission of Nuclear Energy and the International Atomic Energy Agency have played a paramount role in our country, concerning the biological tissue processing, which can be radio-sterilized as human skin, pig skin, amniotic membrane, human bone and bovine bone. The frozen radio.-sterilized human skin processing began in 2001, by means of putting into practice the knowledge acquired in training courses through the IAEA and the experience transferred by experts who visited our laboratory. The human skin processing of dead donor can be divided into 6 stages: a) Profuse washing with physiological sterilized serum in to remove the microorganisms, chemical and pharmacological compounds; b) immersion in glycerol solution at 10% to better keep the stored tissues; c) packing, to avoid post manipulation of the sterilized tissue; d) microbiological controls which allow and guarantee a sterility assurance level of 10 6 ; e) radio-sterilization, technique that consists of exposing the grafts to electromagnetic gamma waves which eliminate the microorganisms of the tissue, f) and finally, dispatching and liberation of the frozen sterilized human skin for its clinical use in different centers that take care of burned people. The LPTR receives feedback from surgeons who have used these tissues in order to improve the processing stages based in an integral quality system ISO 9001.2000. The State Health System in our country counts on limited and scarce resources to implement synthetic substitutes that is why It is considered necessary to spread the use of these noble tissues which have sterility assurance and they are processed at low price

  4. Development of a computational system for management of risks in radiosterilization processes of biological tissues

    International Nuclear Information System (INIS)

    Montoya, Cynara Viterbo

    2009-01-01

    Risk management can be understood to be a systematic management which aims to identify record and control the risks of a process. Applying risk management becomes a complex activity, due to the variety of professionals involved. In order to execute risk management the following are requirements of paramount importance: the experience, discernment and judgment of a multidisciplinary team, guided by means of quality tools, so as to provide standardization in the process of investigating the cause and effects of risks and dynamism in obtaining the objective desired, i.e. the reduction and control of the risk. This work aims to develop a computational system of risk management (software) which makes it feasible to diagnose the risks of the processes of radiosterilization of biological tissues. The methodology adopted was action-research, according to which the researcher performs an active role in the establishment of the problems found, in the follow-up and in the evaluation of the actions taken owing to the problems. The scenario of this action-research was the Laboratory of Biological Tissues (LTB) in the Radiation Technology Center IPEN/CNEN-SP - Sao Paulo/Brazil. The software developed was executed in PHP and Flash/MySQL language, the server (hosting), the software is available on the Internet (www.vcrisk.com.br), which the user can access from anywhere by means of the login/access password previously sent by email to the team responsible for the tissue to be analyzed. The software presents friendly navigability whereby the user is directed step-by-step in the process of investigating the risk up to the means of reducing it. The software 'makes' the user comply with the term and present the effectiveness of the actions taken to reduce the risk. Applying this system provided the organization (LTB/CTR/IPEN) with dynamic communication, effective between the members of the multidisciplinary team: a) in decision-making; b) in lessons learned; c) in knowing the new risk

  5. Sera radiosterilization: studies and applications

    International Nuclear Information System (INIS)

    Michelin, Severino C.

    2000-01-01

    The application of ionizing radiation for sterilization of animal serum increased rapidly over the last few years, due to the fact that most radiation-resistant living organisms (fungi, bacteria, viruses, etc.) can be readily inactivated without damage to the serum. The quality of sera sterilized by ionizing radiation has been investigated. Radiosterilization was carried out in the frozen state at doses between 25 and 50 kGy. The source of gamma radiation was cobalt 60. To demonstrate that serum proteins did not suffer alterations during the process of irradiation, SDS-PAGE, electrofocusing and non equilibrium pH gradient electrophoresis of the sera were carried out before and after irradiation. The biological efficiency of the irradiated sera was demonstrated by growth curves of several cell lines in cell cultures supplemented with it. The results demonstrated that radiosterilization is a simple and effective method for sera. (author)

  6. Radiosterilization process control in plants using electron accelerators; Kontrola procesu sterylizacji radiacyjnej w stacjach korzystajacych z akceleratorow elektronow

    Energy Technology Data Exchange (ETDEWEB)

    Stuglik, Z [Institute of Nuclear Chemistry and Technology, Warsaw (Poland)

    1997-10-01

    Electron beam parameters deciding the irradiation dose in radiosterilization plants should be continuously controlled during the process. Dosimetric procedure suitable to irradiated material and dose range should be chosen. The practical advice and directions in this subject have been done. 7 refs.

  7. Radiosterilization of Medical Products and Recommended Code of Practice. Proceedings of a Symposium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1967-09-15

    Proceedings of a Symposium organized by the IAEA and held in Budapest, 5-9 June 1967, together with the IAEA recommended 'Code of Practice for Radiosterilization of Medical Products' resulting from a panel meeting held in Vienna, December 1966, and considered at the Symposium. The meeting was attended by 160 participants from 25 Member States and 3 international organizations. The commercial use of ionizing radiation for sterilizing medical supplies extends back to the early 1960s. The ability of the process to sterilize products made of materials such as plastics, which are destroyed by traditional sterilization procedures, has promoted much new thinking in product design. Most important is the ability of the radiation to sterilize items finally sealed and packed for dispatch, eliminating risk of recontamination. Some new fields of research are discussed in the Proceedings. The Code of Practice, drawn up by experts at several meetings, is aimed at producing uniform, safe procedures throughout the world, facilitating international trade in radiosterilized products. Contents: Introductory lecture; Radiosterilization of pharmaceuticals and bioproducts (12 papers); Radiosterilization of biological tissues (6 papers); Vaccine production by ionizing radiation (5 papers); Radiosterilization of medical devices and supplies (4 papers); Radiosensitivity of micro-organisms and microbiological testing (4 papers); Technical and economic aspects of radiosterilization (6 papers); Code of practice for radiosterilization (full code and 1 review paper). The Code of Practice is in English. Each paper is in its original language (29 English, 5 French, 4 Russian and 1 Spanish) and is preceded by an abstract in English with one in the original language if this is not English. Discussions are in English. (author)

  8. Radiosterilization of Medical Products and Recommended Code of Practice. Proceedings of a Symposium

    International Nuclear Information System (INIS)

    1967-01-01

    Proceedings of a Symposium organized by the IAEA and held in Budapest, 5-9 June 1967, together with the IAEA recommended 'Code of Practice for Radiosterilization of Medical Products' resulting from a panel meeting held in Vienna, December 1966, and considered at the Symposium. The meeting was attended by 160 participants from 25 Member States and 3 international organizations. The commercial use of ionizing radiation for sterilizing medical supplies extends back to the early 1960s. The ability of the process to sterilize products made of materials such as plastics, which are destroyed by traditional sterilization procedures, has promoted much new thinking in product design. Most important is the ability of the radiation to sterilize items finally sealed and packed for dispatch, eliminating risk of recontamination. Some new fields of research are discussed in the Proceedings. The Code of Practice, drawn up by experts at several meetings, is aimed at producing uniform, safe procedures throughout the world, facilitating international trade in radiosterilized products. Contents: Introductory lecture; Radiosterilization of pharmaceuticals and bioproducts (12 papers); Radiosterilization of biological tissues (6 papers); Vaccine production by ionizing radiation (5 papers); Radiosterilization of medical devices and supplies (4 papers); Radiosensitivity of micro-organisms and microbiological testing (4 papers); Technical and economic aspects of radiosterilization (6 papers); Code of practice for radiosterilization (full code and 1 review paper). The Code of Practice is in English. Each paper is in its original language (29 English, 5 French, 4 Russian and 1 Spanish) and is preceded by an abstract in English with one in the original language if this is not English. Discussions are in English. (author)

  9. Radiosterilization and gas sterilization

    International Nuclear Information System (INIS)

    Schultz, H.A.; Gruenewald, T.

    1987-01-01

    The book presents a survey of the principles of cold sterilization by radiation or gas, and also of the problems involved. The reader who has to do with sterilization of some kind or other, as e.g. sterilization of medicaments, medical supplies, medical device, drugs, grafts, or food, will find comprehensive information on the various available methods and their effects, as well as on monitoring procedures and techniques, together with proposals for efficient documentation and validation of partial sterilization processes. The introduction summarizes the potentials of sterilization by radiation, and the subsequent by radiation, and the subsequent chapters explain the specific applicabilities of radiosterilization along with the most important criteria for evaluating the sterilizing efficiency. The information on the legal situation and requirements takes into account the second amendment of the Medical Preparations Act. With 38 figs., 14 tabs [de

  10. Allogeneic bone transplants, biostatic, frozen, radiosterilized, for application in the traumatology of the motion organs

    International Nuclear Information System (INIS)

    Marczynski, W.

    2007-01-01

    Lecture presents statistical analysis of more than three tendon's of clinical cases of the motion organ transplantations. However, to store these organs they should be effectively sterilized. Irradiation should be accounted as one of such methods

  11. Microbiological problems in radiosterilization

    International Nuclear Information System (INIS)

    Czerniawski, E.

    1997-01-01

    Microbiological problems connected with radiosterilization of medical materials, pharmaceuticals and cosmetics have been discussed in detail. Dose-response relationship for different bacteria has been shown. Recommended sterilization and postirradiation control procedures have been described. 24 refs, 6 figs, 5 tabs

  12. Development of a computational system for management of risks in radiosterilization processes of biological tissues; Desenvolvimento de um sistema computacional de gerenciamento de riscos em processos de radioesterilizacao de tecidos biologicos

    Energy Technology Data Exchange (ETDEWEB)

    Montoya, Cynara Viterbo

    2009-07-01

    Risk management can be understood to be a systematic management which aims to identify record and control the risks of a process. Applying risk management becomes a complex activity, due to the variety of professionals involved. In order to execute risk management the following are requirements of paramount importance: the experience, discernment and judgment of a multidisciplinary team, guided by means of quality tools, so as to provide standardization in the process of investigating the cause and effects of risks and dynamism in obtaining the objective desired, i.e. the reduction and control of the risk. This work aims to develop a computational system of risk management (software) which makes it feasible to diagnose the risks of the processes of radiosterilization of biological tissues. The methodology adopted was action-research, according to which the researcher performs an active role in the establishment of the problems found, in the follow-up and in the evaluation of the actions taken owing to the problems. The scenario of this action-research was the Laboratory of Biological Tissues (LTB) in the Radiation Technology Center IPEN/CNEN-SP - Sao Paulo/Brazil. The software developed was executed in PHP and Flash/MySQL language, the server (hosting), the software is available on the Internet (www.vcrisk.com.br), which the user can access from anywhere by means of the login/access password previously sent by email to the team responsible for the tissue to be analyzed. The software presents friendly navigability whereby the user is directed step-by-step in the process of investigating the risk up to the means of reducing it. The software 'makes' the user comply with the term and present the effectiveness of the actions taken to reduce the risk. Applying this system provided the organization (LTB/CTR/IPEN) with dynamic communication, effective between the members of the multidisciplinary team: a) in decision-making; b) in lessons learned; c) in knowing

  13. Radiolysis and radiosterilization of drugs

    International Nuclear Information System (INIS)

    Zeegers, F.; Crucq, A.S.; Gibella, M.; Tilquin, B.

    1993-01-01

    Can the absence of increased toxicological danger in irradiated foods be applied with confidence to drugs. The World Health Organization stated that up to 10 kGy there is no toxicological hazard. However, even if the irradiated drugs meet official standards, it would have to be established that any traces of radiolysis product formed are not toxic. All the tests from PHARMACOPEIA are not appropriate to detect the radiolysis and new physicochemical tests have to be used. Chromatographic detection of the radiosterilization of antibiotics may be advantageously used when the pharmaceuticals are not radio-resistant. The main obstacle to practical application is the low sensitivity of the detectors in liquid-liquid chromatography, a re-irradiation of the suspected samples will be necessary after preliminary chromatographic studies. 8 figs

  14. Progress of radiosterilization in the Argentine Republic

    International Nuclear Information System (INIS)

    Mariano, E.E.; Mugliaroli, H.A.

    1975-01-01

    The technological and economic advantages of radiation as a means of sterilization have led to a steady expansion of its use. With the significant increase in the radiosterilization of medical products, the health authorities have established standards for the use of radiation for that purpose. These standards will be incorporated in the next edition of the Argentine Pharmacopoeia. In general, Argentine legislation in this area is based on the IAEA's Code of Practice for Radiosterilization of Medical Products. The microbiology services of Argentina's National Atomic Energy Commission (CNEA) determine the number of viable microorganisms in each product and package the product before irradiation. The controls are carried out on random samples. At the same time, the chemistry laboratories carry out quality controls on new products which have received sterilizing doses of gamma radiation. The gas sterilization methods employed most widely in the industrial manufacture of thermolabile products involve the use of ethylene oxide or formaldehyde. The cost of this process is influenced considerably by the fact that Argentina has to import ethylene oxide. The low penetrating power of formaldehyde means that the package containing the product must still be open at the time of sterilization if an adequate safety margin is to be ensured; consequently, one needs sterile installations for the post-irradiation sealing of packages. The capital and operating coats of such installations are high. A comparison has been made of the costs of sterilizing 11000 m 3 of a product with a density of 0.1 g/cm 3 and the following relative values obtained: ethylene oxide, 399.2; formaldehyde, 947.5; gamma radiation, 166.0. Studies of the effects of sterilizing doses on certain pharmaceutical products have demonstrated that the radiosterilization of some drugs is possible. The CNEA has designed an installation for the radiosterilization of medical products; the installation would have a 500000-Ci

  15. Morphological and histological damage on reproduction organ of radio-sterilized male fruit flies bactrocera carambolae (drew & hancock) (diptera; tephritidae)

    International Nuclear Information System (INIS)

    Achmad Nasroh Kuswadi

    2011-01-01

    It is known that gamma irradiation of 90 Gy on pupae of Bactrocera carambolae (Drew & Hancock) fruit fly induced sterility on the adults, however limited data on the cause of sterility is available. To obtain such information, morphological and histological damages on the reproduction organ of male adult flies emerged from irradiated pupae were observed. Pupae of 9 day-old were irradiated with 90 Gy gamma, and the male adults of 7 and 14 day-old emerged from the pupae were dissected to obtained the testis. Morphology and size of the testis of irradiated and unirradiated flies were observed under the microscopes, each in 10 replicates. Preparate of the testis were also made and observed under the microscopes of 400 magnification. The results showed that significant damages were found on testis of the irradiated B. carambolae flies due to irradiation, so that the growth of the organ disturbed as shown by the smallers size of the irradiated testis as compare to the normal one. On the irradiated 7 day-old flies, the length and width of testis were 25.9 and 30.2 % smaller, while on those of 14 day-old the testis were 39.20 and 44.42 % smaller, than the normal. Besides smaller in size, dead germinal cells on the testis preparate were also observed. It is concluded that sterility on the male flies was due to the damage on the germinal cells so that abnormal spermatogenesis process happened. The smaller in size of the testis, is also differentiate between of the irradiated from the normal flies of B. carambolae. (author)

  16. Present studies on the radiosterilized drugs

    International Nuclear Information System (INIS)

    Marciniec, B.; Dettlaff, K.

    2007-01-01

    Lecture presents present status of radiosterilization of drugs and medical materials as compared to other sterilization methods. Literature review is shown on degradation of different kinds of drugs sterilized upon action of the sterilising doses of radiation

  17. Radiosterilization of medical products, pharmaceuticals and bioproducts

    International Nuclear Information System (INIS)

    1967-01-01

    A Panel on the Radiosterilization of Medical Products, Pharmaceuticals and Bioproducts was convened by the International Atomic Energy Agency on 17-19 January 1966 at its headquarters in Vienna. The purpose of the meeting was to survey the activities of the Member States in this field with a view to preparing the way for an international code of practice for the radiosterilization of medical products, in conformity with existing legal international rules. Refs, figs and tabs

  18. Economic aspects of radiosterilization; Aspekty ekonomiczne sterylizacji radiacyjnej

    Energy Technology Data Exchange (ETDEWEB)

    Zimek, Z [Institute of Nuclear Chemistry and Technology, Warsaw (Poland)

    1997-10-01

    The economic analysis of radiosterilization have been done. The costs have been estimated on the example of Electron Accelerator Irradiation Plant for Radiosterilization working in Institute of Nuclear Chemistry and Technology, Warsaw. 3 tabs.

  19. Organizing Process

    DEFF Research Database (Denmark)

    Hull Kristensen, Peer; Bojesen, Anders

    This paper invites to discuss the processes of individualization and organizing being carried out under what we might see as an emerging regime of change. The underlying argumentation is that in certain processes of change, competence becomes questionable at all times. The hazy characteristics...... of this regime of change are pursued through a discussion of competencies as opposed to qualifications illustrated by distinct cases from the Danish public sector in the search for repetitive mechanisms. The cases are put into a general perspective by drawing upon experiences from similar change processes...... in MNCs. The paper concludes by asking whether we can escape from a regime of competence in a world defined by a rhetoric of change and create a more promising world in which doubt and search serve as a strategy for gaining knowledge and professionalism that improve on our capability for mutualism....

  20. Electron accelerators for radiosterilization; Akceleratory elektronow dla potrzeb sterylizacji radiacyjnej

    Energy Technology Data Exchange (ETDEWEB)

    Zimek, Z [Institute of Nuclear Chemistry and Technology, Warsaw (Poland)

    1997-10-01

    The applications of electron accelerators in commercial plants for radiosterilization have been shown. Advantages of such irradiation source have been presented. The types and parameters of accelerators being installed in worldwide irradiation plants for radiosterilization have been listed as well. 2 tabs.

  1. Effects of Radiosterilization on Sealed Aqueous Solutions

    International Nuclear Information System (INIS)

    Pandula, E.L.; Farkas, E.; Rácz, I.

    1967-01-01

    For aqueous solutions sensitive to heat,and in connection with the use of plastic ampoules, the need for applying radiosterilization is growing. Studying the possibilities of radiosterilization, experiments were made with the following: 0.1% atropine, 1.0% morphine, and 2% lidocain in aqueous solutions. The aim of the work was to establish whether the active ingredients of the injections suffer decomposition or not, to study the factors influencing the degradation and, furthermore, to make attempts to prevent decomposition. The samples were irradiated by 420 Ci 60 Co γ-radiation source. The applied doses were 1 to 2.5 Mrad, with a 10 4 to 2.5 x 10 5 rad/h dose intensity. After irradiation the change in colour, pH-value, concentration and UV-spectra were studied. Changes of the last three types were found. Studying the factors influencing decomposition it has been found that the degree of degradation was increased by the increase of radiation dose, increase of concentration, decrease of dose intensity, and increase of oxygen content in the atmosphere over the solution. Attempts were made to prevent degradation. Solutions were prepared with sulphite, ascorbic acid, and AET, and some measure of success was achieved, especially with the sulphite addition. (author)

  2. Present studies on the radio-sterilized drugs

    International Nuclear Information System (INIS)

    Marciniec, B.; Dettlaff, K.

    2007-01-01

    Lecture presents present status of radiosterilization of drugs and medical materials as compared to other sterilization methods. Literature review is shown on degradation of different kinds of drugs sterilized upon action of the sterilising doses of radiation

  3. International regulations concerning radiosterilization; Aktualne przepisy miedzynarodowe dotyczace sterylizacji radiacyjnej

    Energy Technology Data Exchange (ETDEWEB)

    Kaluska, I [Institute of Nuclear Chemistry and Technology, Warsaw (Poland)

    1997-10-01

    European norms (EN 552) and international regulations (ISO 11137) concerning commercial radiosterilization have been described. Licensing of irradiation installation as well as sterilization procedure requirements, and routine control have been discussed in detail. 3 refs.

  4. Compatibility of polymeric materials with the radiosterilization of disposable medical products

    International Nuclear Information System (INIS)

    Gonzalez, M.E.

    1990-01-01

    The semiindustrial plant of irradiation located at the Atomic Center of Ezeiza entered into operation 20 years ago. This plant has a nominal activity of 3.7 x 10 16 Bq (10 6 Ci) and is presently operating with 1.78 x 10 16 Bq (4.8 x 10 5 Ci). The facility allows working in pilot plant scale for the study of industrial applications and also performs commercial services, the most important of which considering its volume, economic significance and social function is the radiosterilization of disposable medical products. Approximately 29,000 m 3 have been processed in this period, most of the materials being polymers, as component parts of the products as well as packaging. To validate the process of radiosterilization the materials compatibility with ionizing radiation must be known. In the department that operates the irradiation plant, the polymer laboratory is involved in the development of industrial applications and also in the subject of compatibility of polymers with radiosterilization. The laboratory gives advice on request about selection of materials as well as relevant information for the evaluation of radiation resistance and stability, including exposition doses for the samples and mechanical, physical or chemical tests according to the kind of product. In many occasions this laboratory has had to undertake these tests because local manufacturers of medical products not always have adequate facilities for quality control. Among mechanical tests the area under the stress-strain curve as a measure of the strain the material can undergo without fracture is perhaps the best for the evaluation of degradation. Among physical properties it is important to evaluate discoloration, usual in plastics irradiation, and concerning chemical tests the detection of migration of components from the polymer proves important in some cases. Although the irradiator cannot assume any responsibility concerning compatibility, local experience has shown the importance of having a

  5. Microbiological problems in radiosterilization; Zagadnienia mikrobiologiczne w sterylizacji radiacyjnej

    Energy Technology Data Exchange (ETDEWEB)

    Czerniawski, E [Lodz Univ. (Poland)

    1997-10-01

    Microbiological problems connected with radiosterilization of medical materials, pharmaceuticals and cosmetics have been discussed in detail. Dose-response relationship for different bacteria has been shown. Recommended sterilization and postirradiation control procedures have been described. 24 refs, 6 figs, 5 tabs.

  6. Review of the Code of Practice for the Radiosterilization of Medical Products

    International Nuclear Information System (INIS)

    Kallings, L.O.

    1967-01-01

    The background of the IAEA recommendations for a Code of Practice is outlined. The possibility of laying down broad safety margins based on scientific foresight and detailed advanced planning will serve to guide the rapidly accelerating acceptance of radiosterilization by industry, especially in those firms producing supplies for use in medicine and surgery. Production control should be attuned to the scientific and technological advances, and it is becoming clear that the focus of control should be moved away from sterility testing of the finished products to hygienic and sterile operations during the manufacturing operations themselves. The contamination of the product before sterilization should already have been kept to a minimum, and this pre-sterilization level of contamination should be regularly recorded using bacteriological tests. The choice of dosage should be based on average pre-sterilization counts and the inactivation factors found desirable for die intended use of the product. On commissioning, or whenever an existing process is altered, the efficiency of the irradiation facility must be tested using microbiological reference standards. The margin of safety should be checked by using deliberately contaminated articles. However, the backbone of the control procedures must still be dosimetry. The preparation of a Code of Practice for the Radiosterilization of Medical Products will constitute a challenge to operators working with other sterilizing procedures. (author)

  7. Radiosterilization dosimetry by electron-spin resonance spectroscopy. Cefotetan

    International Nuclear Information System (INIS)

    Basly, J.P.; Longy, I.; Bernard, M.

    1998-01-01

    As an alternative to heat and gas exposure sterilization, ionizing radiation is gaining interest as a sterilization process for medicinal products. Nevertheless, essentially for economic profit, unauthorized and uncontrolled use of radiation processes may be expected. In this context, it is necessary to find methods of distinguishing between irradiated and nonirradiated pharmaceuticals. In the absence of suitable detection methods, our attention was focused on electron-spin resonance (ESR) spectrometry. A third generation cephalosporin, cefotetan, was chosen as a model; this antibiotic is a potential candidate for radiation treatment due to its thermosensitivity. While the ESR spectra of a nonirradiated sample presents no signal, a nonsymmetrical signal, dependent on the irradiation dose, is found in irradiated samples. The number of free radicals was estimated by comparing the second integral from radiosterilized samples and a diphenylpicryl hydrazyl reference. Estimation of the number of free radicals gives 7x10 17 radicals g -1 at 20kGy (1.1x10 16 radicals in 15mg). From this result, the G-value (number of radicals (100eV) -1 ) could be estimated as 0.6. Decay of radicals upon storage were modeled using a bi-exponential function. The limit of detection of free radicals after irradiation at 25kGy is up to two years. This result agrees with those obtained on other cephalosporins. Aside from qualitative detection, ESR spectrometry can be used for dose estimation. Linear regression is applicable for doses lower than 20kGy. Since the radiation dose selected must always be based upon the bioburden of the products and the degree of sterility required (EN 552 and ANSI/AAMI/ISO 11137), 25kGy could no longer be accepted as a 'routine' dose for sterilizing a pharmaceutical. Doses in the 5-20kGy range could be investigated and linear regression appeared to be the least expensive route to follow. The best results for the integration of the curves were obtained with

  8. Evolution of the Radio-sterilized Tissues Bank of the Instituto Nacional de Investigaciones Nucleares

    International Nuclear Information System (INIS)

    Martinez P, M. E.; Reyes F, M. L.; Luna Z, D.

    2013-10-01

    The Radio-sterilized Tissues Bank (RTB) of the Instituto Nacional de Investigaciones Nucleares (ININ) was established in 1997, as national project supported by the IAEA, who provided equipment, training and expert missions. In July of 1999, the Secretaria de Salud (Mexico) granted the sanitary license to the RTB. The first radio-sterilized tissue was the amnion. Later on, the process of frozen and lyophilized pig skin was development. Both tissue types are used as biological dressings in patient with burns, ulcers or on injuries difficult to heal, the amnion is also used for the damage treatment in the ocular surface. In 2003, the ININ improved the facilities of the RTB and in August of that same year the certification of the Quality Administration System was obtained under the standard ISO 9001:2000, at the present time ISO 9001:2008. The support of the IAEA granted to Mexico was of 1997-2004 and 2009-2012, by means of regional and inter regional projects where was obtained equipment and training mainly, for personal of the ININ and other institutions. With the last project supported by the IAEA, two very important documents were generated for the tissues bank of Argentina, Brazil, Colombia, Costa Rica, Cuba, Ecuador, El Salvador, Mexico, Peru, Uruguay and Venezuela, strengthening the interaction among these countries. To offer more radio-sterilized tissues to the medical community, in June of 2007 the RTB signed and agreement with the Secretaria de Salud of the Mexico State by means of the Centro Estatal de Transplantes del Estado de Mexico, for the process of muscle-skeletal tissue, skin and amnion. At present, besides amnion and pig skin, in the RTB there is in existence powdered and chips bone; concluding the validation stage the human skin process is. As a social function of the ININ, the RTB has contributed to the health improvement of patients of more than 50 hospital institutions, mainly those that assist to patient of low resources in different cities of

  9. Organic food processing

    DEFF Research Database (Denmark)

    Kahl, Johannes; Alborzi, Farnaz; Beck, Alexander

    2014-01-01

    In 2007 EU Regulation (EC) 834/2007 introduced principles and criteria for organic food processing. These regulations have been analysed and discussed in several scientific publications and research project reports. Recently, organic food quality was described by principles, aspects and criteria....... These principles from organic agriculture were verified and adapted for organic food processing. Different levels for evaluation were suggested. In another document, underlying paradigms and consumer perception of organic food were reviewed against functional food, resulting in identifying integral product...... identity as the underlying paradigm and a holistic quality view connected to naturalness as consumers' perception of organic food quality. In a European study, the quality concept was applied to the organic food chain, resulting in a problem, namely that clear principles and related criteria were missing...

  10. ESR measurements and the detection of radiosterilization of drugs

    International Nuclear Information System (INIS)

    Gibella, M.; Crucq, A.S.; Tilquin, B.

    1993-01-01

    The ESR spectrum of trapped radicals in irradiated solid antibiotics could permit the detection of the radiosterilization. The ESR signal is detected only after radiolysis; at room temperature, this ESR spectrum is observable for a few hours or until several years. The rate of the metathesis reactions can be fast or very slow, the reaction path is unknown,. However, in many cases, the polycrystalline solid phase exhibits its ability to keep radicals for a long period of time and the detection of the radiolysis is possible during this period. 10 figs., 1 tab

  11. Amnion s and radio-sterilized porcine skin use as potential matrices for the development of human skin substitutes

    International Nuclear Information System (INIS)

    Martinez P, M. E.; Reyes F, M. L.; Reboyo B, D.; Velasquillo M, M. C.; Sanchez S, R.; Brena M, A. M.; Ibarra P, J. C.

    2014-10-01

    The injuries by burns constitute a primordial problem of public health; they cause a high mortality index, severe physical and psychological disability, etc. The autologous skin transplant is the replacement therapy recommended for its treatment, but in patients that present a high percentage of burnt skin; this is not possible to carry out. Another strategy is the transplant of donated skin; however, due to the little donation that exists in our country is not very feasible to apply this treatment. A challenge of the tissues engineering is to develop biological skin substitutes, based on cells and amnion s, favoring the cutaneous regeneration and quick repair of injuries, diminishing this way the hospitalization expenses. At present skin substitutes that can equal to the same skin do not exist. On the other hand, the mesenchymal stromal cells (Msc) represent an alternative to achieve this objective; since has been demonstrated that the Msc participate in the tissue repair by means of inhibition of pro-inflammatory cytokines and differentiation to dermal fibroblasts and keratinocytes. To apply the Msc in cutaneous injuries a support material is required that to allow transplanting these cells to a lesion or burn. The radio-sterilized human amnion and the radio-sterilized porcine skin, processed by the Radio-Sterilized Tissues Bank of the Instituto Nacional de Investigaciones Nucleares (ININ), are biomaterials that are used as temporary cutaneous coverings. We suppose that these two matrices will be appropriate for the growth and maintenance in cultivation of the Msc, to generate two biological skin substitutes, in collaboration with the Biotechnology Laboratory of the Instituto Nacional de Rehabilitacion. (Author)

  12. Radiosterilization or sterilization by steam. Procedures for sterilization of spices

    International Nuclear Information System (INIS)

    Warmbold, J.

    1994-01-01

    The article compares two different methods for the sterilization of spices, namely radiosterilization and sterilization with steam. The first method applies ionizing radiation which can alter the chemical composition of the products. Tests have shown, however, that radiation doses up to 10 kGy will not induce the formation of carcinogenic agents in the foodstuffs, or of toxic substances, and thus are a wholesome method of preservation. Any modifications of taste, color or smell, or loss of vitamins, can be avoided by proper dose control and standard irradiation conditions. Sterilization by steam is a method achieving substantial suppression of the formation of germs, aerobic spores, yeasts, mould, and gramnegative germs, while preserving in most cases the essential oils. It may result in sensoric alterations, i.e affect the color, smell or taste, but in general the spices thus treated preserved their characteristic properties. The method is a good alternative to radiosterilization. The article adds some concluding information on mandatory labelling of irradiated food imported from third countries

  13. Present studies on the radio-sterilized drugs; Aktualny stan badan nad lekami sterylizowanymi radiacyjnie

    Energy Technology Data Exchange (ETDEWEB)

    Marciniec, B; Dettlaff, K [Department of Pharmaceutical Chemistry, Poznan University of Medical Sciences, Poznan (Poland)

    2007-07-01

    Lecture presents present status of radiosterilization of drugs and medical materials as compared to other sterilization methods. Literature review is shown on degradation of different kinds of drugs sterilized upon action of the sterilising doses of radiation.

  14. Organic waste incineration processes

    Energy Technology Data Exchange (ETDEWEB)

    Lemort, F.; Charvillat, J.P.; Nabot, J.P. [CEA Valrho, Bagnols sur Ceze Cedex (France); Chateauvieux, H.; Thiebaut, C. [CEA Valduc, 21 - Is-sur-Tille (France)

    2001-07-01

    Nuclear activities produce organic waste compatible with thermal processes designed to obtain a significant weight and volume reduction as well as to stabilize the inorganic residue in a form suitable for various interim storage or disposal routes. Several processes may be implemented (e.g. excess air, plasma, fluidized bed or rotating furnace) depending on the nature of the waste and the desired objectives. The authors focus on the IRIS rotating-kiln process, which was used for the first time with radioactive materials during the first half of 1999. IRIS is capable of processing highly chlorinated and {alpha}-contaminated waste at a rate of several kilograms per hour, while limiting corrosion due to chlorine as well as mechanical entrainment of radioactive particles in the off-gas stream. Although operated industrially, the process is under continual development to improve its performance and adapt it to a wider range of industrial applications. The main focus of attention today is on adapting the pyrolytic processes to waste with highly variable compositions and to enhance the efficiency of the off-gas purification systems. These subjects are of considerable interest for a large number of heat treatment processes (including all off-gas treatment systems) for which extremely durable, high-performance and low-flow electrostatic precipitators are now being developed. (author)

  15. Organic waste incineration processes

    International Nuclear Information System (INIS)

    Lemort, F.; Charvillat, J.P.; Nabot, J.P.; Chateauvieux, H.; Thiebaut, C.

    2001-01-01

    Nuclear activities produce organic waste compatible with thermal processes designed to obtain a significant weight and volume reduction as well as to stabilize the inorganic residue in a form suitable for various interim storage or disposal routes. Several processes may be implemented (e.g. excess air, plasma, fluidized bed or rotating furnace) depending on the nature of the waste and the desired objectives. The authors focus on the IRIS rotating-kiln process, which was used for the first time with radioactive materials during the first half of 1999. IRIS is capable of processing highly chlorinated and α-contaminated waste at a rate of several kilograms per hour, while limiting corrosion due to chlorine as well as mechanical entrainment of radioactive particles in the off-gas stream. Although operated industrially, the process is under continual development to improve its performance and adapt it to a wider range of industrial applications. The main focus of attention today is on adapting the pyrolytic processes to waste with highly variable compositions and to enhance the efficiency of the off-gas purification systems. These subjects are of considerable interest for a large number of heat treatment processes (including all off-gas treatment systems) for which extremely durable, high-performance and low-flow electrostatic precipitators are now being developed. (author)

  16. Criteria for permission of radiosterilized products to application in medicine; Zasady dopuszczania wyrobow sterylizowanych radiacyjnie do stosowania w medycynie

    Energy Technology Data Exchange (ETDEWEB)

    Achmatowicz, T [Instytut Lekow, Warsaw (Poland)

    1997-10-01

    The criteria being used in Poland for permission of radiosterilized medical materials to commercial application result from regulations being in force. The international regulations are also taken into account. The all criteria and procedure needed for any product become accepted for radiosterilization and commercial medical use have been presented and discussed. 1 tab.

  17. Radiosterilization of Tissues Preserved for Clinical Purposes: Effect on Tissue Antigenicity

    International Nuclear Information System (INIS)

    Ostrowski, K.; Kossowska, B.; Moskalewski, S.; Komender, A.; Kurnatowski, W.

    1967-01-01

    The first part of the paper contains practical considerations on the radiosterilization of preserved human bone, human and calf cartilage, cow’s fascia and aponeurosis, based on material from the Tissue Bank which produces about 2500 transplants yearly. The method of preservation and packing of each type of tissue is mentioned briefly. The preserved tissues are irradiated in a cobalt bomb or in a nuclear reactor. The conditions of irradiation and the control of sterility are described. The advantages and disadvantages of radiosterilization are discussed on the basis of the authors’ own experience and clinical reports of surgeons using radiosterilized tissues in practice. In the second part of the paper, experimental studies on the influence of freezing, lyophilization and radiosterilization on tissue antigenicity are reported. The regional lymph node reacts to an antigenic stimulus by an increased production of large, pyroninophylic cells, so-called ''blast'' cells. The rabbits used as recipients received grafts of allogeneic cancellous bone, fresh or subjected to different experimental procedures. Smears from lymph node cell suspension were prepared and the percentage of blast cells was estimated. On the basis of the lymph node response, it appears that freezing and lyophilization, as well as radiosterilization, may abolish the antigenicity of cancellous bone. The practical implication of these results for methods of preservation of tissues for clinical purposes is discussed. (author)

  18. Radiosterilization and steam autoclaving sterilization effects on phosphite antioxidant stability

    International Nuclear Information System (INIS)

    Yagoubi, N.; Boucherie, P.; Ferrier, D.

    1997-01-01

    While the radiosterilization by γ rays, is mainly employed for medical devices, this procedure is not commonly used to sterilize and decontaminate raw material and finished product used in the pharmaceutical industry. Depending on the countries, the requirements for obtaining approval to treat this class of product with γ rays may be different. Usually it is the responsibility of the manufacturer to demonstrate not only the integrity of the irradiated product, but olso its efficiency, safety and quality. Our work consists of a comparative study of the effects of γ radiotreatment at 25 kGy and steam sterilisation on phosphite antioxidant incorporated in polypropylene. The γ radiosensitivity compared with thermolability of this antioxidant was studied by reversed phase HPLC, Fourier transform infrared (IRFT) and differential scanning calorimetry (DSC). The results obtained proved that the phosphite incorporated into the polymer and treated with the two types of sterilisation is rapidly oxidized in phosphate. Nevertheless, this oxidation is more important when using radiotreatment at 25 kGy. (orig.)

  19. Clinical uses of radiosterilized freeze-dried human bone: its application in buccomaxillary surgery

    International Nuclear Information System (INIS)

    Wolfsohn, B.; Taramasso, F.; Godoy, J.; Wodowoz, O.; Saldias, M.; Silva, W.; Machin, D.; Sanchez, G.; Alvarez, I.

    2008-01-01

    Full text: The objective of this paper is to evaluate the uses of different human bone tissue allografts in bucomaxillary surgery between 2005 and 2007. Presentation of our experience using single freeze dried bone allografts and associated to bovine collagen membranes (commercial registered). Twenty patients were treated with cortical struts, cancellous chips, morsellized and morsellized demineralized bone. All the grafts were processed at the INDT multi tissue bank from cardiac arrest and brain death cadaveric donors. All the tissues were radiosterilized by Gamma radiation. Bone allografts were used: 1) to optimize bone support increasing maxillar or mandible bone before implant surgery. 2) in dehiscences and fissures during the implant surgery. 3) to stimulate bone regeneration in alveolar cavity, post-apicectomies, and cystectomies as well as for bone defects. The patients were periodically evaluated using standardized protocols. All the cases were successful showing clinic and radiologically osseointegration after 6 and 12 months. Results were evaluated considering surgical technique and patients bucomaxillary rehabilitation. Clinical uses of bone allografts confirm in our experience, as scientific literature outcomes shows, are useful in patients that refuses autografts ablation. (Author)

  20. Excitonic processes at organic heterojunctions

    Science.gov (United States)

    He, ShouJie; Lu, ZhengHong

    2018-02-01

    Understanding excitonic processes at organic heterojunctions is crucial for development of organic semiconductor devices. This article reviews recent research on excitonic physics that involve intermolecular charge transfer (CT) excitons, and progress on understanding relationships between various interface energy levels and key parameters governing various competing interface excitonic processes. These interface excitonic processes include radiative exciplex emission, nonradiative recombination, Auger electron emission, and CT exciton dissociation. This article also reviews various device applications involving interface CT excitons, such as organic light-emitting diodes (OLEDs), organic photovoltaic cells, organic rectifying diodes, and ultralow-voltage Auger OLEDs.

  1. Organization as Process of Communication

    DEFF Research Database (Denmark)

    Schoeneborn, Dennis; Vasquez, Consuelo; Cornelissen, Joep

    Within process views on organization, one central question is how organizations (as entities) are constituted by processes (i.e. non-entities). The answer to this question depends on the ways in which organizational scholars imagine organization, e.g., through rhetorical figures like metaphors...... of a metonymy is Morgan’s image of ‘organization as flux and transformation’ – an idea that has inspired a larger body of research that is known today as “process organization studies”. In this paper we suggest to draw on the neighboring metonymic image ‘organization as communication’ which not only presents...... a novel way of thinking about the inherently intertwined nature of metaphor and metonymy, but also expands processual thinking about organizations especially with regards to the entity-process relation....

  2. Social identity process within organizations

    OpenAIRE

    Bazarov, Takhir; Kuzmina, Maria

    2005-01-01

    Expanding and complex social realities cause new types of identity. Variety in organizations and workgroups (where people are involved), implies a special kind of social identity which can be defined as professional, organizational or managerial. The study of the social identity processes in organizations is a new interdisciplinary sphere that is presented especially commonly in European Social Psychology. The result of its theoretical comprehension is Social Identity Theory. In the article l...

  3. STRATEGIC TRANSFORMATION PROCESSES IN ORGANIZATIONS

    Directory of Open Access Journals (Sweden)

    JOSÉ G. VARGAS HERNÁNDEZ

    2003-01-01

    Full Text Available The objective of this paper is to analyze the transformation processes in strategy formulation inrelation to the evolution of the organization. It is determined that strategic thinking and strategyformulation has been a unique privilege of top management until the 70’s when the context wascharacterized by being more or less stable, in which the comparative advantages were sufficient toachieve the organization’s success starting from the role of traditional management.However, when the competitive environment changes due to the turbulence phenomena, with morecomplexity and turbulence, top management of organizations must respond to increasing demandsimposed by the new social and economic conditions. And through a continuous process of innovationof all activities of the business to search for sustainable competitive advantages founded on intangibleelements, specifically on the “knowledge” which is internalized in all the members of the organization.Thus, although strategic formulation is still faculty of top management, in some way it is influenced byother members of the organization.

  4. Evolution of the Radio-sterilized Tissues Bank of the Instituto Nacional de Investigaciones Nucleares; Evolucion del Banco de Tejidos Radioesterilizados del Instituto Nacional de Investigaciones Nucleares

    Energy Technology Data Exchange (ETDEWEB)

    Martinez P, M. E.; Reyes F, M. L.; Luna Z, D., E-mail: esther.martinez@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2013-10-15

    The Radio-sterilized Tissues Bank (RTB) of the Instituto Nacional de Investigaciones Nucleares (ININ) was established in 1997, as national project supported by the IAEA, who provided equipment, training and expert missions. In July of 1999, the Secretaria de Salud (Mexico) granted the sanitary license to the RTB. The first radio-sterilized tissue was the amnion. Later on, the process of frozen and lyophilized pig skin was development. Both tissue types are used as biological dressings in patient with burns, ulcers or on injuries difficult to heal, the amnion is also used for the damage treatment in the ocular surface. In 2003, the ININ improved the facilities of the RTB and in August of that same year the certification of the Quality Administration System was obtained under the standard ISO 9001:2000, at the present time ISO 9001:2008. The support of the IAEA granted to Mexico was of 1997-2004 and 2009-2012, by means of regional and inter regional projects where was obtained equipment and training mainly, for personal of the ININ and other institutions. With the last project supported by the IAEA, two very important documents were generated for the tissues bank of Argentina, Brazil, Colombia, Costa Rica, Cuba, Ecuador, El Salvador, Mexico, Peru, Uruguay and Venezuela, strengthening the interaction among these countries. To offer more radio-sterilized tissues to the medical community, in June of 2007 the RTB signed and agreement with the Secretaria de Salud of the Mexico State by means of the Centro Estatal de Transplantes del Estado de Mexico, for the process of muscle-skeletal tissue, skin and amnion. At present, besides amnion and pig skin, in the RTB there is in existence powdered and chips bone; concluding the validation stage the human skin process is. As a social function of the ININ, the RTB has contributed to the health improvement of patients of more than 50 hospital institutions, mainly those that assist to patient of low resources in different cities of

  5. Determination of sensitivity of staphylococcus SPP to xeno-graft of pig to be radio-sterilized subsequently with ionizing

    International Nuclear Information System (INIS)

    Rojas Tapia, Carolina

    2011-01-01

    The use of the pork skin heterograft or xenograft, as a temporary biological dressing in the treatment of extreme burns patients, may cause a risk due to the transmission of pathogenic bacteria of the genus Staphylococcus spp colonizing the outer part of the skin. The objective of this study was to determine the sensitivity of Staphylococcus spp from porcine xenograft, against ionizing energy and by antibiogram, which was carried out in the Radio-sterilized Biological Tissue Processing Laboratory (LPTR) of the Chilean Nuclear Energy Commission, in together with the Microbiology Laboratory of the Santo Tomas University. The hides of pigs are processed to obtain sterile porcine xenograft. The determination of the radiosensitivity of Staphylococcus hyicus and epidermidis, required the use of 15 samples of pig skin of 0.5g sterile, for each species of Staphylococcus analyzed. Subsequently, the pig skins are contaminated with Staphylococcus hyicus and epidermidis. Once the contamination was finished, the samples were subjected to an irradiation dose of 0.2; 0.4; 0.6; 0.8 KGy, plus a control (without irradiation), to finally perform a microbiological count, which allowed to determine a DIO value that for Staphylococcus hyicus that was approximately 0.25KGy and for Staphylococcus epidermidis was approximately 0.29KGy. The microbial susceptibility tested by traditional antibiogram for Staphylococcus aureus, hyicus and epidermidis, allowed concluding that all staphylococci analyzed in the present study were sensitive to antibiotics: Cloxacillin, Amoxicillin + Ac clavulanic and Gentamicin, however were resistant to Penicillin and Erythromycin

  6. Radiation preservation of biological tissues with special emphasis on immunological alterations. Part of a coordinated programme on radiosterilization of medical products and biological tissues

    International Nuclear Information System (INIS)

    Feher, I.

    1977-01-01

    A method suitable for clinical use and preparations of tendon and skin preserved by lyophilization and radiosterilization were investigated. The fate of the graft was detected by histological and electronmicroscopical investigations. We demonstrated that the implanted preparation was desorganized and was absorbed within six weeks. Clinical examinations were made on pig-tendon preparations. Patients recovered without difficulties in every case. Skin preparations were prepared of pig-skin. It was demonstrated by indirect haemagglutination that pig-skin antigenity was decreased by approximately two orders of magnitude during the preservation process. The clinical application of skin preparations has been used for nearly two years. It is effectively used as a biological dressing for the covering of wound surface in case of burn injuries

  7. Hydrothermal processing of actinide contaminated organic wastes

    International Nuclear Information System (INIS)

    Worl, A.; Buelow, S.J.; Le, L.A.; Padilla, D.D.; Roberts, J.H.

    1997-01-01

    Hydrothermal oxidation is an innovative process for the destruction of organic wastes, that occurs above the critical temperature and pressure of water. The process provides high destruction and removal efficiencies for a wide variety of organic and hazardous substances. For aqueous/organic mixtures, organic materials, and pure organic liquids hydrothermal processing removes most of the organic and nitrate components (>99.999%) and facilitates the collection and separation of the actinides. We have designed, built and tested a hydrothermal processing unit for the removal of the organic and hazardous substances from actinide contaminated liquids and solids. Here we present results for the organic generated at the Los Alamos National Laboratory Plutonium Facility

  8. Amnion s and radio-sterilized porcine skin use as potential matrices for the development of human skin substitutes; Uso de amnios y piel porcina radioesterilizados como matrices potenciales para el desarrollo de sustitutos de piel humana

    Energy Technology Data Exchange (ETDEWEB)

    Martinez P, M. E.; Reyes F, M. L.; Reboyo B, D. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Velasquillo M, M. C.; Sanchez S, R.; Brena M, A. M.; Ibarra P, J. C., E-mail: esther.martinez@inin.gob.mx [Instituto Nacional de Rehabilitacion, Calz. Mexico-Xochimilco No. 289, Col. Arenal de Guadalupe, 14389 Mexico D. F. (Mexico)

    2014-10-15

    The injuries by burns constitute a primordial problem of public health; they cause a high mortality index, severe physical and psychological disability, etc. The autologous skin transplant is the replacement therapy recommended for its treatment, but in patients that present a high percentage of burnt skin; this is not possible to carry out. Another strategy is the transplant of donated skin; however, due to the little donation that exists in our country is not very feasible to apply this treatment. A challenge of the tissues engineering is to develop biological skin substitutes, based on cells and amnion s, favoring the cutaneous regeneration and quick repair of injuries, diminishing this way the hospitalization expenses. At present skin substitutes that can equal to the same skin do not exist. On the other hand, the mesenchymal stromal cells (Msc) represent an alternative to achieve this objective; since has been demonstrated that the Msc participate in the tissue repair by means of inhibition of pro-inflammatory cytokines and differentiation to dermal fibroblasts and keratinocytes. To apply the Msc in cutaneous injuries a support material is required that to allow transplanting these cells to a lesion or burn. The radio-sterilized human amnion and the radio-sterilized porcine skin, processed by the Radio-Sterilized Tissues Bank of the Instituto Nacional de Investigaciones Nucleares (ININ), are biomaterials that are used as temporary cutaneous coverings. We suppose that these two matrices will be appropriate for the growth and maintenance in cultivation of the Msc, to generate two biological skin substitutes, in collaboration with the Biotechnology Laboratory of the Instituto Nacional de Rehabilitacion. (Author)

  9. Organizational structure in process-based organizations

    NARCIS (Netherlands)

    Vanhaverbeke, W.P.M.; Torremans, H.P.M.

    1999-01-01

    This paper investigates the role of the organization structure in process-based organizations. We argue that companies cannot be designed upon organizational processes only or that process management can be simply imposed as an additional structural dimension on top of the existing functional or

  10. Investigation of radiosterilization feasibility of sulfamethoxazole by ESR spectroscopy

    Science.gov (United States)

    Çolak, Şeyda

    2017-12-01

    In the present study, the spectroscopic features of the radiolytic intermediates that were produced in gamma-irradiated (5, 10, 25 and 50 kGy) sulfamethoxazole (SMX) have been investigated by electron spin resonance (ESR) spectroscopy and the radiation sterilization feasibility of SMX by ionizing radiation was examined. Gamma-irradiated SMX exhibited a complex ESR spectrum consisting of 13 resonance lines where spectral parameters for the central resonance line were found to be g = 2.0062 and ΔHpp = 0.6 mT. The radiation yield of SMX was calculated to be relatively low (G = 0.1) by ESR spectroscopy and no meaningful difference was observed in the comparison of unirradiated and 50 kGy gamma irradiated SMX by the Fourier transform infrared (FT-IR) technique, confirming that SMX is a radioresistive material. Although SMX could not be accepted to be a good dosimetric material, the identification of irradiated SMX from the unirradiated sample was possible even for the low absorbed radiation doses and for a relatively long time (three months) after the irradiation process. Decay activation energy of the radical species, which is mostly responsible for the central intense resonance line, is calculated to be 45.15 kJ/mol by using the signal intensity decay data derived from annealing studies. Four radical species with different spectroscopic properties were accepted to be responsible for the ESR spectra of gamma-irradiated SMX, by simulation calculations. It is concluded that SMX and SMX-containing drugs can be sterilized by gamma radiation and ESR spectroscopy is an appropriate technique for the characterization of these induced radical intermediates during the gamma irradiation process of SMX. Toxicology tests should also be done for its safe usage.

  11. Assessment of changes in chemical structure of vitamin K (K-thrombyl), due to γ-radiosterilization

    International Nuclear Information System (INIS)

    Ossman, A.R.E.

    1986-01-01

    The present application of radiosterilization is confined primarily to those materials which cannot be heat sterilized. This study involves: a) Finding the lowest possible dose that will produce a sterile product. b) Comparison of the physical and chemical properties of the irradiated products of different dose levels with those sterilized by other stated method (pharmacopoeial or currently applied methods), and of control composed of untreated ampoules. (orig.) [de

  12. Preliminary field studies on the control of the red palm weevil, Rhynchophorus ferrugineus Oliv., using radiosterilized males

    International Nuclear Information System (INIS)

    Rahalkar, G.W.; Harwalkar, M.R.; Rananavare, H.D.

    1977-01-01

    Feasibility of using sterile male release method for the control of red palm weevil, Rhynchophorus ferrungineus Oliv., a serious pest of coconut and other cultivated palms in India was investigated. A total of over 5000 radiosterilized males were released in an 800 acre coconut plantation near Kayangulam in Kerala. Data on the fertility pattern of native females is presented and the factors affecting the efficacy of sterile male release for control of this insect are discussed. (author)

  13. Process Consultation: Its Role in Organization Development.

    Science.gov (United States)

    Schein, Edgar H.

    This volume focuses on the process by which the consultant builds readiness for organizational development (OD) programs, actually conducts training, and works with the key individuals of an organization as part of an OD program. Part I describes in some detail the human processes in organizations--communication, functional roles of group members,…

  14. The Process Perspective on Trust in Organizations

    DEFF Research Database (Denmark)

    Jagd, Søren

    Several trust researchers have pointed to the relevance of the process perspective for understanding trust in organizations. In this paper I review the attempts to apply the process perspective in trust research distinguishing between a soft and a strong process perspective. It appears that nearly......’s history? A few examples of studies applying a strong process perspective to trust in organizations is discussed.  Summarising, I argue that the process perspective, in general, may contribute furthering the understanding of the complexities of the development of trust over time and that the strong process...

  15. Ethical principles and practice in organic processing

    DEFF Research Database (Denmark)

    Hansen, Mette Weinreich; Nielsen, T; Kristensen, Niels Heine

    2006-01-01

    market for new actors – especially this paper will concentrate on the processing companies who, for a large part, took interest in the organic production after the ending of the pioneer phase. The authors emphasize the importance of reflecting values in relation to organic food production especially...

  16. Organic Process Technology Valuation: Cyclohexanone Oxime Syntheses

    Science.gov (United States)

    Cannon, Kevin C.; Breen, Maureen P.

    2010-01-01

    Three contemporary processes for cyclohexanone oxime synthesis are evaluated in a case study. The case study introduces organic chemistry students to basic cost accounting to determine the most economical technology. Technical and financial aspects of these processes are evaluated with problem-based exercises that may be completed by students…

  17. Chromosome studies on bone marrow cells of chinese hamsters fed a radiosterilized diet

    International Nuclear Information System (INIS)

    Renner, H.W.

    1977-01-01

    Metaphase preparations of chromosomes from bone marrow cells of Chinese hamsters were examined for mutagenic effects following the feeding of a radiosterilized diet. No increase in the incidence of structural chromosomal aberrations was observed. As far as numerical aberrations were concerned, the proportion of cells with polyploidy increased to between 4 to 5 times the control level, irrespective of the moisture content of the diet. This polyploidy effect occurred very early, being detectable within 24 h, if the diet fed had been irradiated with an absorbed dose of 4.5x10 6 rad. The incidence of polyploidy remained below 0.5%, however, nor did it rise with higher radiation doses. When the feeding of the irradiated diet was stopped, the proportion of polyploid cells returned to the control level within a maximum of 6 weeks. If the diet was stored (initially) for 6 weeks following irradiation before being fed to the animals no increase in the number of polyploid cells was noted. These results are not interpreted as a mutagenic effect of the irradiated diet. (author)

  18. Mating competitiveness of Aedes albopictus radio-sterilized males in large enclosures exposed to natural conditions.

    Science.gov (United States)

    Bellini, R; Balestrino, F; Medici, A; Gentile, G; Veronesi, R; Carrieri, M

    2013-01-01

    Mating competitiveness trials have been conducted in large net-screened enclosures (8 by 5 by 2.8 m) built in a natural shaded environment, in the summers of 2006, 2007, 2008, and 2009 in northern Italy. Aedes albopictus (Skuse) males were radio-sterilized by applying gamma radiations at doses in the range 30-60 Gy. Gamma radiation was administered to aged pupae at the rate of 2.3 Gy/min. Reared radiated males (originally collected in Rimini, Forli, Bologna, Matera, Pinerolo) and hybrid radiated males were tested against wild fertile males (originated from eggs collected in Rimini and Cesena) and reared fertile males, in multiple comparisons for mating competitiveness with reared or wild females. The ratio was kept constant at 100-100_100 (fertile males-radiated males_virgin females). Mating competitiveness was estimated through the calculation of the hatching rate of the eggs laid in oviposition traps positioned inside enclosures. No clear effect of the strains tested (reared, wild, or hybrid) was found. Results demonstrated that reducing the radiation dose from 60 to 30 Gy increases males' competitiveness. Laboratory investigations conducted after controversial results in the 2006 preliminary trials, showed that radiation induces precociousness in adult male emergence.

  19. MODELING OF MANAGEMENT PROCESSES IN AN ORGANIZATION

    Directory of Open Access Journals (Sweden)

    Stefan Iovan

    2016-05-01

    Full Text Available When driving any major change within an organization, strategy and execution are intrinsic to a project’s success. Nevertheless, closing the gap between strategy and execution remains a challenge for many organizations [1]. Companies tend to focus more on execution than strategy for quick results, instead of taking the time needed to understand the parts that make up the whole, so the right execution plan can be put in place to deliver the best outcomes. A large part of this understands that business operations don’t fit neatly within the traditional organizational hierarchy. Business processes are often messy, collaborative efforts that cross teams, departments and systems, making them difficult to manage within a hierarchical structure [2]. Business process management (BPM fills this gap by redefining an organization according to its end-to-end processes, so opportunities for improvement can be identified and processes streamlined for growth, revenue and transformation. This white paper provides guidelines on what to consider when using business process applications to solve your BPM initiatives, and the unique capabilities software systems provides that can help ensure both your project’s success and the success of your organization as a whole. majority of medium and small businesses, big companies and even some guvermental organizations [2].

  20. Process integration of organic Rankine cycle

    International Nuclear Information System (INIS)

    Desai, Nishith B.; Bandyopadhyay, Santanu

    2009-01-01

    An organic Rankine cycle (ORC) uses an organic fluid as a working medium within a Rankine cycle power plant. ORC offers advantages over conventional Rankine cycle with water as the working medium, as ORC generates shaft-work from low to medium temperature heat sources with higher thermodynamic efficiency. The dry and the isentropic fluids are most preferred working fluid for the ORC. The basic ORC can be modified by incorporating both regeneration and turbine bleeding to improve its thermal efficiency. In this paper, 16 different organic fluids have been analyzed as a working medium for the basic as well as modified ORCs. A methodology is also proposed for appropriate integration and optimization of an ORC as a cogeneration process with the background process to generate shaft-work. It has been illustrated that the choice of cycle configuration for appropriate integration with the background process depends on the heat rejection profile of the background process (i.e., the shape of the below pinch portion of the process grand composite curve). The benefits of integrating ORC with the background process and the applicability of the proposed methodology have been demonstrated through illustrative examples.

  1. Resensi Buku: Organization Strategy, Structure, and Process

    Directory of Open Access Journals (Sweden)

    Ayi Ahadiyat

    2009-08-01

    Full Text Available Book ReviewJudul Buku    : Organization Strategy, Structure, and ProcessPenulis    : Raymond E. Miles and Charles C. SnowPenerbit     : McGraw-Hill Kogakusha, Ltd (International Student Edition, Tokyo,  274 hlm.Tahun    : 1978

  2. Treating contaminated organics using the DETOX process

    International Nuclear Information System (INIS)

    Elsberry, K.D.; Dhooge, P.M.

    1993-01-01

    Waste matrices containing organics, radionuclides, and metals pose difficult problems in waste treatment and disposal when the organic compounds and/or metals are considered to be hazardous. This paper describes the results of bench-scale studies of DETOX applied to the components of liquid mixed wastes, with the goal of establishing parameters for designing a prototype waste treatment unit. Apparent organic reaction rate orders and the dependence of apparent reaction rate on solution composition and the contact area were measured for vacuum pump oil scintillation fluids, and trichloroethylene. Reaction rate was superior in chloride-based solutions and was proportional to the contact area above about 2% w/w loading of organic. Oxidations in a 4-liter volume, mixed bench-top reactor have given destruction efficiencies of 99.9999 + % for common organics. Reaction rates achieved in the mixed bench-top reactor were one to two orders of magnitude greater than had been achieved in unmixed reactions; a thoroughly mixed reactor should be capable of oxidizing 10 to 100 + grams of organic per liter-hour. Results are also presented on the solvation efficiency of DETOX for mercury, cerium, and neodymium, and for removal/destruction of organics sorbed on vermiculite. The next stage of development will be converting the bench-top unit to continuous processing

  3. Rearrangements of organic peroxides and related processes

    Directory of Open Access Journals (Sweden)

    Ivan A. Yaremenko

    2016-08-01

    Full Text Available This review is the first to collate and summarize main data on named and unnamed rearrangement reactions of peroxides. It should be noted, that in the chemistry of peroxides two types of processes are considered under the term rearrangements. These are conventional rearrangements occurring with the retention of the molecular weight and transformations of one of the peroxide moieties after O–O-bond cleavage. Detailed information about the Baeyer−Villiger, Criegee, Hock, Kornblum−DeLaMare, Dakin, Elbs, Schenck, Smith, Wieland, and Story reactions is given. Unnamed rearrangements of organic peroxides and related processes are also analyzed. The rearrangements and related processes of important natural and synthetic peroxides are discussed separately.

  4. Organic waste processing using molten salt oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Adamson, M. G., LLNL

    1998-03-01

    Molten Salt Oxidation (MSO) is a thermal means of oxidizing (destroying) the organic constituents of mixed wastes, hazardous wastes, and energetic materials while retaining inorganic and radioactive constituents in the salt. For this reason, MSO is considered a promising alternative to incineration for the treatment of a variety of organic wastes. The U. S. Department of Energy`s Office of Environmental Management (DOE/EM) is currently funding research that will identify alternatives to incineration for the treatment of organic-based mixed wastes. (Mixed wastes are defined as waste streams which have both hazardous and radioactive properties.) One such project is Lawrence Livermore National Laboratory`s Expedited Technology Demonstration of Molten Salt Oxidation (MSO). The goal of this project is to conduct an integrated demonstration of MSO, including off-gas and spent salt treatment, and the preparation of robust solid final forms. Livermore National Laboratory (LLNL) has constructed an integrated pilot-scale MSO treatment system in which tests and demonstrations are presently being performed under carefully controlled (experimental) conditions. The system consists of a MSO process vessel with dedicated off-gas treatment, a salt recycle system, feed preparation equipment, and equipment for preparing ceramic final waste forms. In this paper we describe the integrated system and discuss its capabilities as well as preliminary process demonstration data. A primary purpose of these demonstrations is to identify the most suitable waste streams and waste types for MSO treatment.

  5. Process Improvement in a Radically Changing Organization

    Science.gov (United States)

    Varga, Denise M.; Wilson, Barbara M.

    2007-01-01

    This presentation describes how the NASA Glenn Research Center planned and implemented a process improvement effort in response to a radically changing environment. As a result of a presidential decision to redefine the Agency's mission, many ongoing projects were canceled and future workload would be awarded based on relevance to the Exploration Initiative. NASA imposed a new Procedural Requirements standard on all future software development, and the Center needed to redesign its processes from CMM Level 2 objectives to meet the new standard and position itself for CMMI. The intended audience for this presentation is systems/software developers and managers in a large, research-oriented organization that may need to respond to imposed standards while also pursuing CMMI Maturity Level goals. A set of internally developed tools will be presented, including an overall Process Improvement Action Item database, a formal inspection/peer review tool, metrics collection spreadsheet, and other related technologies. The Center also found a need to charter Technical Working Groups (TWGs) to address particular Process Areas. In addition, a Marketing TWG was needed to communicate the process changes to the development community, including an innovative web site portal.

  6. BRANDING PROCESS - FUNDAMENTAL PROCESS IN THE TEXTI LE INDUSTRY ORGANIZATIONS

    Directory of Open Access Journals (Sweden)

    PURCAREA Anca Alexandra

    2014-05-01

    Full Text Available More companies in textile industry organizations understand that in making a decision a key factor is the performance of organizational processes. Products are becoming more numerous and increasingly resemble each other.In this conditions the brand can make the difference in a highly competitive market. Both academic specialists and professionals believes that the brand has become an intangible capital of a company which ensures its long-term profitability. In a globalized economy brand break the barriers of space enabling the company to have a great vision, far beyond its reach. Methodology was based on a bibliographical research. The research has identified the major role that brands can play both for customers and manufacturers in the textile Industry organizations. In conclusion literature and experience has shown that large companies both brands operating in B2B markets and the B2C markets, have an increasingly higher for long-term competitive advantage.

  7. Process of pulmonary rehabilitation and program organization.

    Science.gov (United States)

    Wouters, E F M; Augustin, I M L

    2011-09-01

    Pulmonary rehabilitation programs are highly directed to return patients suffering from chronic lung diseases to a state of self-help. These programs are largely organized as temporary interventions in a highly fragmented delivery care system for patients with chronic respiratory conditions. In an optimal health care organizational structure, pulmonary rehabilitation needs to be considered as an essential part of an individualized, integrated care process, organized from the vantage point of the patient and the patients'health continuum. Pulmonary rehabilitation programs need to become organized as patient-centered care, respectful of and responsive to individual patient preferences, needs and values. Partnering and communication skills are considered as drivers for successful rehabilitation. Assessment is considered as the cornerstone to evaluate the individual needs and problems in order to develop an individualized intervention. Pulmonary rehabilitation programs need to move away from a supply-driven functional organizational structure towards integrated structures, including the full range of medical expertise, technical skills and specialized facilities needed to compete on added value in the management of patients with chronic respiratory diseases.

  8. Macroecology of unicellular organisms - patterns and processes.

    Science.gov (United States)

    Soininen, Janne

    2012-02-01

    Macroecology examines the relationship between organisms and their environment at large spatial (and temporal) scales. Typically, macroecologists explain the large-scale patterns of abundance, distribution and diversity. Despite the difficulties in sampling and characterizing microbial diversity, macroecologists have recently also been interested in unicellular organisms. Here, I review the current advances made in microbial macroecology, as well as discuss related ecosystem functions. Overall, it seems that microorganisms suit surprisingly well to known species abundance distributions and show positive relationship between distribution and adundance. Microbial species-area and distance-decay relationships tend to be weaker than for macroorganisms, but nonetheless significant. Few findings on altitudinal gradients in unicellular taxa seem to differ greatly from corresponding findings for larger taxa, whereas latitudinal gradients among microorganisms have either been clearly evident or absent depending on the context. Literature also strongly emphasizes the role of spatial scale for the patterns of diversity and suggests that patterns are affected by species traits as well as ecosystem characteristics. Finally, I discuss the large role of local biotic and abiotic variables driving the community assembly in unicellular taxa and eventually dictating how multiple ecosystem processes are performed. Present review highlights the fact that most microorganisms may not differ fundamentally from larger taxa in their large-scale distribution patterns. Yet, review also shows that many aspects of microbial macroecology are still relatively poorly understood and specific patterns depend on focal taxa and ecosystem concerned. © 2011 Society for Applied Microbiology and Blackwell Publishing Ltd.

  9. IMPROVEMENT OF BUSINESS PROCESSES OF THE ORGANIZATION CONSIDERING RISK

    Directory of Open Access Journals (Sweden)

    Дмитро Іванович БЕДРІЙ

    2015-05-01

    Full Text Available It is proposed to analyze the methods of optimization of business processes of the organization. The results of which is proposed to apply to the method of reengineering of business processes of the organization. Conclusions about the need to implement business process reengineering of the organization of the risk having an impact on its operations are made.

  10. Business process reengineering in Ethiopian public organizations ...

    African Journals Online (AJOL)

    Journal Home > Vol 1, No 2 (2009) > ... organizations, the effort required was too much as compared to the benefits obtained. ... These stages are automation, horizontal integration, BPR, network redesign and organizational scope redefinition.

  11. Organization of bubble chamber image processing

    International Nuclear Information System (INIS)

    Gritsaenko, I.A.; Petrovykh, L.P.; Petrovykh, Yu.L.; Fenyuk, A.B.

    1985-01-01

    A programme of bubble chamber image processing is described. The programme is written in FORTRAN, it is developed for the DEC-10 computer and is designed for operation of semi-automation processing-measurement projects PUOS-2 and PUOS-4. Fornalization of the image processing permits to use it for different physical experiments

  12. Organic Farming, Gender, and the Labor Process

    Science.gov (United States)

    Hall, Alan; Mogyorody, Veronika

    2007-01-01

    This paper seeks to explain variations in gender participation in farm production and decision-making through an analysis of organic farm types, sizes, and orientations. Based on both survey and case study data, the analysis shows that female farmers on vegetable farms and mixed livestock/cash crop farms are more likely to be involved in farm…

  13. LOGISTICAL PROCESSES IN MILITARY AVIATION ORGANIZATIONS

    Directory of Open Access Journals (Sweden)

    Jarosław KOZUBA

    2017-03-01

    Full Text Available This article examines airbases as organizational units of the Polish Air Force from the perspective of executing logistical processes, with a particular emphasis on multirole aircraft maintenance processes. We selected air force bases that deal with multirole aircraft in order to become acquainted with the opinions of service processing executors. The observations of most immediate executors of the processes allow us to examine the possibilities for their enhancement and development. We presented the dependencies between different factors occurring in logistics processes, and their relationships and conditionings [3, 6, 7]. We described these factors using comparative parameters by means of the analysis and tools recommended in the science of management [2, 3, 8], while the collected material was developed using statistical tools and computer software [1]. The article is illustrated with numerous pictures and tables.

  14. Validation of radiosterilization dose of human skin dressings for burnt treatment: preliminary study

    International Nuclear Information System (INIS)

    Castro, E.

    2008-01-01

    Full text: Due to the need for better materials to treat burnt patients, the Peruvian Institute of Nuclear Energy (IPEN) and the Rosa Guerzoni Chambergo Tissue Bank are collaborating for developing human skin dressings. Skin was procured from living donors, who surgically were performed a dermolipectomy. Exclusion criteria, stated by the Peruvian Organization for Transplant and Donation were observed. Glycerolized human skin dressings were processed at the tissue bank and sent to IPEN, where the gamma irradiation sterilizing dose was determined. The purpose of this work is to validate the radiation sterilization dose delivered to human skin dressings using the IAEA Code of Practice for the Radiation Sterilization of Tissue Allografts: Requirements for Validation and Routine Control. A batch of human skin dressings was tested. Average values of bioburden present in ten samples was 30 UFC/item, obtaining a sub-sterilization dose of 4 kGy. Irradiations were performed in the GammacellExcel 220. Sterility tests performed fulfilled the requirements established by the Code, achieving a validated dose value of 19.7 kGy. This preliminary study, that should be repeated in two other batches of processed human skin, allows to diminish 25 kGy the sterilizing dose to the stated above dose value, in a frame of a quality assurance system that also comprises the processes held at tissue banks previous irradiation. It also permit the availability of these materials in Peruvian hospitals. (Author)

  15. Breakdown in the Organ Donation Process and Its Effect on Organ Availability

    Directory of Open Access Journals (Sweden)

    Manik Razdan

    2015-01-01

    Full Text Available Background. This study examines the effect of breakdown in the organ donation process on the availability of transplantable organs. A process breakdown is defined as a deviation from the organ donation protocol that may jeopardize organ recovery. Methods. A retrospective analysis of donation-eligible decedents was conducted using data from an independent organ procurement organization. Adjusted effect of process breakdown on organs transplanted from an eligible decedent was examined using multivariable zero-inflated Poisson regression. Results. An eligible decedent is four times more likely to become an organ donor when there is no process breakdown (adjusted OR: 4.01; 95% CI: 1.6838, 9.6414; P<0.01 even after controlling for the decedent’s age, gender, race, and whether or not a decedent had joined the state donor registry. However once the eligible decedent becomes a donor, whether or not there was a process breakdown does not affect the number of transplantable organs yielded. Overall, for every process breakdown occurring in the care of an eligible decedent, one less organ is available for transplant. Decedent’s age is a strong predictor of likelihood of donation and the number of organs transplanted from a donor. Conclusion. Eliminating breakdowns in the donation process can potentially increase the number of organs available for transplant but some organs will still be lost.

  16. The evaluation process of short training sessions in organizations

    NARCIS (Netherlands)

    Overschie, M.G.F.; Lukosch, H.K.; De Vries, P.

    This paper presents a critical reflection of the evaluation of learning processes in organizations. Based on learning and evaluation theories and concepts we discuss qualitative and quantitative evaluation processes, and its relationship to short training sessions to foster sustainable development.

  17. Breakdown in the organ donation process and its effect on organ availability.

    Science.gov (United States)

    Razdan, Manik; Degenholtz, Howard B; Kahn, Jeremy M; Driessen, Julia

    2015-01-01

    Background. This study examines the effect of breakdown in the organ donation process on the availability of transplantable organs. A process breakdown is defined as a deviation from the organ donation protocol that may jeopardize organ recovery. Methods. A retrospective analysis of donation-eligible decedents was conducted using data from an independent organ procurement organization. Adjusted effect of process breakdown on organs transplanted from an eligible decedent was examined using multivariable zero-inflated Poisson regression. Results. An eligible decedent is four times more likely to become an organ donor when there is no process breakdown (adjusted OR: 4.01; 95% CI: 1.6838, 9.6414; P organs yielded. Overall, for every process breakdown occurring in the care of an eligible decedent, one less organ is available for transplant. Decedent's age is a strong predictor of likelihood of donation and the number of organs transplanted from a donor. Conclusion. Eliminating breakdowns in the donation process can potentially increase the number of organs available for transplant but some organs will still be lost.

  18. Substitution of Organic Solvents in Selected Industrial Cleaning Processes

    DEFF Research Database (Denmark)

    Jacobsen, Thomas; Rasmussen, Pia Brunn

    1997-01-01

    Volatile organic solvents (VOC)are becoming increasingly unwanted in industrial processes. Substitution of VOC with non-volatile, low-toxic compounds is a possibility to reduce VOC-use. It has been successfully demonstrated, that organic solvents used in cleaning processes in sheet offset printing...

  19. PROCESS DOCUMENTATION: A MODEL FOR KNOWLEDGE MANAGEMENT IN ORGANIZATIONS.

    Science.gov (United States)

    Haddadpoor, Asefeh; Taheri, Behjat; Nasri, Mehran; Heydari, Kamal; Bahrami, Gholamreza

    2015-10-01

    Continuous and interconnected processes are a chain of activities that turn the inputs of an organization to its outputs and help achieve partial and overall goals of the organization. These activates are carried out by two types of knowledge in the organization called explicit and implicit knowledge. Among these, implicit knowledge is the knowledge that controls a major part of the activities of an organization, controls these activities internally and will not be transferred to the process owners unless they are present during the organization's work. Therefore the goal of this study is identification of implicit knowledge and its integration with explicit knowledge in order to improve human resources management, physical resource management, information resource management, training of new employees and other activities of Isfahan University of Medical Science. The project for documentation of activities in department of health of Isfahan University of Medical Science was carried out in several stages. First the main processes and related sub processes were identified and categorized with the help of planning expert. The categorization was carried out from smaller processes to larger ones. In this stage the experts of each process wrote down all their daily activities and organized them into general categories based on logical and physical relations between different activities. Then each activity was assigned a specific code. The computer software was designed after understanding the different parts of the processes, including main and sup processes, and categorization, which will be explained in the following sections. The findings of this study showed that documentation of activities can help expose implicit knowledge because all of inputs and outputs of a process along with the length, location, tools and different stages of the process, exchanged information, storage location of the information and information flow can be identified using proper

  20. A network perspective on the processes of empowered organizations.

    Science.gov (United States)

    Neal, Zachary P

    2014-06-01

    Organizational empowerment is a multi-faceted concept that involves processes occurring both within and between organizations that facilitate achievement of their goals. This paper takes a closer look at three interorganizational processes that lead to empowered organizations: building alliances, getting the word out, and capturing others' attention. These processes are located within the broader nomological network of empowerment and organizational empowerment, and are linked to particular patterns of interorganizational relationships that facilitate organizations' ability to engage in them. A new network-based measure, γ-centrality, is introduced to capture the particular network structure associated with each process to be assessed. It is demonstrated first in a hypothetical organizational network, then applied to take a closer look at organizational empowerment in the context of a coordinating council composed of human service agencies. The paper concludes with a discussion of the implications of relationships between these processes, and the potential for unintended consequences in the empowerment of organizations.

  1. Wastewater treatment processes for the removal of emerging organic pollutants

    Directory of Open Access Journals (Sweden)

    Ainhoa Rubio Clemente

    2013-12-01

    Full Text Available Emerging organic pollutants form a very heterogeneous group of substances that have negative effects on aquatic organisms, so they should be removed from the environment. Unfortunately, conventional processes in wastewater treatment plants, especially biological ones, are inefficient in the degradation of these substances. It is therefore necessary to evaluate and optimize the effectiveness of the treatments, including advanced oxidation and membrane filtration processes. However, both techniques have drawbacks that may limit their stand-alone application, so it is proposed that the best solution may be to combine these technologies with biological processes to treat wastewater contaminated with emerging organic pollutants.

  2. Organic Foods manufacturing and Processing: The New Way of Life

    OpenAIRE

    Jalan, Vishal

    2007-01-01

    Organic is the fastest growing sector of the food industry with global sales approaching US $40 billion in 2006. Growing health-consciousness among consumers globally has resulted in high demand for Fresh and more importantly Processed Organic Food. This value-addition can generate large number of jobs in rural areas in India and Africa.

  3. New growing media and value added organic waste processing

    NARCIS (Netherlands)

    Blok, C.; Rijpsma, E.; Ketelaars, J.J.M.H.

    2016-01-01

    Public pressure to use peat alternatives in horticultural rooting media offers room for the re-use of local organic waste materials. The re-use of organic wastes requires value added processing such as composting, co-composting, digestion, fractioning/sieving, pressing, binding, stabilising by

  4. On the Design of Information-Processing and Decisionmaking Organizations

    National Research Council Canada - National Science Library

    Boettcher, Kevin L; Levis, Alexander H

    1982-01-01

    ... and a response selection stage. The total rate of internal processing of each decisionmaker is constrained by bounded rationality, while the performance of the organization must satisfy specified goals...

  5. Assessing the process and content of strategy in different organizations

    NARCIS (Netherlands)

    Romme, A.G.L.; Kunst, P.; Schreuder, H.; Spangenberg, J.

    1990-01-01

    This paper deals with a quantitative assessment of strategy content and strategy process characteristics. The framework used is based on the concept of strategic logics. The empirical study involves six organizations in The Netherlands. Both the content and the process dimension of strategy-making

  6. Innovation process and innovativeness of facility management organizations

    NARCIS (Netherlands)

    Mudrak, T.; Wagenberg, van A.F.; Wubben, E.F.M.

    2005-01-01

    Purpose - The innovation patterns and processes in facility management (FM) organizations are crucial for the development of FM as a discipline, but they are not yet fully explored and understood. This paper aims to clarify FM innovation from the perspective of innovation processes and the

  7. ORGANIZATION OF INFORMATION INTERACTION OF AIRPORT PRODUCTION PROCESSES

    Directory of Open Access Journals (Sweden)

    Yakov Mikhajlovich Dalinger

    2017-01-01

    Full Text Available The organization of service production attributed to airports activity is analyzed. The importance and the actuality of information interaction problem solution between productive processes as a problem of organization of modern produc- tion are shown.Possibilities and features of information interaction system construction in form of multi-level hierarchical struc- ture have been shown. The airport is considered as an enterprise aimed at service production where it is necessary to analyze much in- formation in a limited time-frame. The production schedule often changes under the influence of many factors. This leads to the increase of the role of computerization and informatization of production processes what predetermines automation of production, creation of information environment and organization of information interaction needed for realization of production processes. The integrated organization form is proposed because it is oriented to the integration of different processes into a universal production system and it allows to conduct the coordination of local goals of particular processes in the context of the global purpose aimed at the improvement of the effectiveness of the airport activity. The main conditions needed for organization of information interaction between production processes and techno- logical operations are considered, and the list of the following problems is determined. The attention is paid to the necessity of compatibility of structure and organization of interaction system in the conditions of the airline and the necessity of be- ing its reflection in the information space of the airline. The usefulness of the intergrated organization form of information interaction based on information exchange between processes and service customers according to the network structure is explained. Multi-level character of this structure confirms its advantage over other items, however it also has a series of features presented

  8. Fermentation process for the production of organic acids

    Science.gov (United States)

    Hermann, Theron; Reinhardt, James; Yu, Xiaohui; Udani, Russell; Staples, Lauren

    2018-05-01

    This invention relates to improvements in the fermentation process used in the production of organic acids from biological feedstock using bacterial catalysts. The improvements in the fermentation process involve providing a fermentation medium comprising an appropriate form of inorganic carbon, an appropriate amount of aeration and a biocatalyst with an enhanced ability to uptake and assimilate the inorganic carbon into the organic acids. This invention also provides, as a part of an integrated fermentation facility, a novel process for producing a solid source of inorganic carbon by sequestering carbon released from the fermentation in an alkali solution.

  9. Lost in processing? Perceived healthfulness, taste and caloric content of whole and processed organic food.

    Science.gov (United States)

    Prada, Marília; Garrido, Margarida V; Rodrigues, David

    2017-07-01

    The "organic" claim explicitly informs consumers about the food production method. Yet, based on this claim, people often infer unrelated food attributes. The current research examined whether the perceived advantage of organic over conventional food generalizes across different organic food types. Compared to whole organic foods, processed organic foods are less available, familiar and prototypical of the organic food category. In two studies (combined N = 258) we investigated how both organic foods types were perceived in healthfulness, taste and caloric content when compared to their conventional alternatives. Participants evaluated images of both whole (e.g., lettuce) and processed organic food exemplars (e.g., pizza), and reported general evaluations of these food types. The association of these evaluations with individual difference variables - self-reported knowledge and consumption of organic food, and environmental concerns - was also examined. Results showed that organically produced whole foods were perceived as more healthful, tastier and less caloric than those produced conventionally, thus replicating the well-established halo effect of the organic claim in food evaluation. The organic advantage was more pronounced among individuals who reported being more knowledgeable about organic food, consumed it more frequently, and were more environmentally concerned. The advantage of the organic claim for processed foods was less clear. Overall, processed organic (vs. conventional) foods were perceived as tastier, more healthful (Study 1) or equally healthful (Study 2), but also as more caloric. We argue that the features of processed food may modulate the impact of the organic claim, and outline possible research directions to test this assumption. Uncovering the specific conditions in which food claims bias consumer's perceptions and behavior may have important implications for marketing, health and public-policy related fields. Copyright © 2017 Elsevier

  10. Process-based organization design and hospital efficiency.

    Science.gov (United States)

    Vera, Antonio; Kuntz, Ludwig

    2007-01-01

    The central idea of process-based organization design is that organizing a firm around core business processes leads to cost reductions and quality improvements. We investigated theoretically and empirically whether the implementation of a process-based organization design is advisable in hospitals. The data came from a database compiled by the Statistical Office of the German federal state of Rheinland-Pfalz and from a written questionnaire, which was sent to the chief executive officers (CEOs) of all 92 hospitals in this federal state. We used data envelopment analysis (DEA) to measure hospital efficiency, and factor analysis and regression analysis to test our hypothesis. Our principal finding is that a high degree of process-based organization has a moderate but significant positive effect on the efficiency of hospitals. The main implication is that hospitals should implement a process-based organization to improve their efficiency. However, to actually achieve positive effects on efficiency, it is of paramount importance to observe some implementation rules, in particular to mobilize physician participation and to create an adequate organizational culture.

  11. Method of processing radiation-contaminated organic polymer materials

    International Nuclear Information System (INIS)

    Kobayashi, Yoshii.

    1980-01-01

    Purpose: To process radiation contaminated organic high polymer materials with no evolution of toxic gases, at low temperature and with safety by hot-acid immersion process using sulfuric acid-hydrogen peroxide. Method: Less flammable or easily flammable organic polymers contaminated with radioactive substances, particularly with long life actinoid are heated and carbonized in concentrated sulfuric acid. Then, aqueous 30% H 2 O 2 solution is continuously added dropwise as an oxidizing agent till the solution turns colourless. If the carbonization was insufficient, addition of H 2 O 2 solution is stopped temporarily and the carbonization is conducted again. Thus, the organic polymers are completely decomposed by the wet oxidization. Then, the volume of the organic materials to be discharged is decreased and the radioactive substances contained are simultaneously concentrated and collected. (Seki, T.)

  12. Behaviour of organic matters in uranium ore processing

    International Nuclear Information System (INIS)

    Wu Sanmin

    1991-01-01

    The oxidation-reduction behaviour of organic matters in the course of oxidation roasting, acid leaching and alkali leaching, the regeneration of humic acid and the consumption of reagents are described. The mineralogical characteristics of the organic matter samples were studied. The results show that its organic matter rich in volatile carbon and with the shorter evolutionary process and lower association is easily oxidized with higher consumption of oxidant during its acid leaching; it is easily oxidized with forming humic acid during alkali leaching; and pretreating it by oxidation roasting is beneficial to the oxidation of uranium. On the contrary, the organic matter rich in fixed carbon, and with longer evolutionary process and higher association is difficultly oxidized with lower consumption of oxidant during its acid leaching; it is difficult to regenerate humic acid for it during alkali leaching; and the uranium can be easily reduced and the leaching performance of uranium can be lowered

  13. Management of Multi-projects In a Process oriented Organization

    OpenAIRE

    Macheridis, Nikos; Nilsson, Carl-Henrik

    2006-01-01

    When projects are used as an organisational platform to conduct business, a project can be the only project in the organisation or one amongst several others. The latter case is called multi-project organisation. Usually an organization with a multi-project environment has a base organisation, which can be functional, matrix structure or another. The purpose of this article is to develop a model based on a process oriented organization as a complement to functional or matrix organizational st...

  14. Organic waste process containing at least one radioactive element

    International Nuclear Information System (INIS)

    Le Roy, F.

    1977-01-01

    The description is given of an organic waste process containing at least one element from the group comprising strontium, cesium, iodine and ruthenium. It comprises the introduction of the organic waste and gaseous oxygen in a bath of melted salt containing an alkaline carbonate, the bath being maintained at a high temperature between 400 and 1000 0 C and at a pressure of 0.5 to 10 bars, so that the organic waste is burnt and oxidised at least partly, the element selected being retained by the bath of melted salt [fr

  15. Processing of Unsaturated Organic Acid Aerosols by Ozone

    Science.gov (United States)

    Aloisio, S.; Donaldson, D. J.; Eliason, T. L.; Cziczo, D.; Vaida, V.

    2002-05-01

    We present results of in-situ studies of the oxidative "processing" of organic aerosols composed of unsaturated organic compounds. Aerosol samples of 2-octenoic acid and undecylenic acid were exposed to approx. 10 mbar ozone in a room temperature, atmospheric pressure flow tube reactor. In-situ spectroscopic probing of the reaction mixture, as well as GC-MS analysis of the flow tube effluent, shows evidence of efficient oxidation of double bonds in the organic species, with production of gas-phase and aerosol phase ozonolysis products.

  16. Order out of Randomness: Self-Organization Processes in Astrophysics

    Science.gov (United States)

    Aschwanden, Markus J.; Scholkmann, Felix; Béthune, William; Schmutz, Werner; Abramenko, Valentina; Cheung, Mark C. M.; Müller, Daniel; Benz, Arnold; Chernov, Guennadi; Kritsuk, Alexei G.; Scargle, Jeffrey D.; Melatos, Andrew; Wagoner, Robert V.; Trimble, Virginia; Green, William H.

    2018-03-01

    Self-organization is a property of dissipative nonlinear processes that are governed by a global driving force and a local positive feedback mechanism, which creates regular geometric and/or temporal patterns, and decreases the entropy locally, in contrast to random processes. Here we investigate for the first time a comprehensive number of (17) self-organization processes that operate in planetary physics, solar physics, stellar physics, galactic physics, and cosmology. Self-organizing systems create spontaneous " order out of randomness", during the evolution from an initially disordered system to an ordered quasi-stationary system, mostly by quasi-periodic limit-cycle dynamics, but also by harmonic (mechanical or gyromagnetic) resonances. The global driving force can be due to gravity, electromagnetic forces, mechanical forces (e.g., rotation or differential rotation), thermal pressure, or acceleration of nonthermal particles, while the positive feedback mechanism is often an instability, such as the magneto-rotational (Balbus-Hawley) instability, the convective (Rayleigh-Bénard) instability, turbulence, vortex attraction, magnetic reconnection, plasma condensation, or a loss-cone instability. Physical models of astrophysical self-organization processes require hydrodynamic, magneto-hydrodynamic (MHD), plasma, or N-body simulations. Analytical formulations of self-organizing systems generally involve coupled differential equations with limit-cycle solutions of the Lotka-Volterra or Hopf-bifurcation type.

  17. [Organ donation process: perception by relatives of cadaverous donors].

    Science.gov (United States)

    dosSantos, Marcelo José; Massarollo, Maria Cristina Komatsu Braga

    2005-01-01

    This study aimed to disclose how relatives of cadaverous donors perceive the organ donation process for transplantation. A phenomenological, qualitative research was carried out on the basis of the "situated-phenomenon structure". The statements revealed that, for the relatives of the donors, the process of donation begins with the patients' hospital admission and only ends when they are buried. Furthermore, it is considered bureaucratic, long, consuming and tiring. This situation results in suffering and stress, but there is no regret about the organ donation since, although the pain caused by the loss does not end, the donation initiative comforts and brings satisfaction.

  18. Aqueous organic chemistry in the atmosphere: sources and chemical processing of organic aerosols.

    Science.gov (United States)

    McNeill, V Faye

    2015-02-03

    Over the past decade, it has become clear that aqueous chemical processes occurring in cloud droplets and wet atmospheric particles are an important source of organic atmospheric particulate matter. Reactions of water-soluble volatile (or semivolatile) organic gases (VOCs or SVOCs) in these aqueous media lead to the formation of highly oxidized organic particulate matter (secondary organic aerosol; SOA) and key tracer species, such as organosulfates. These processes are often driven by a combination of anthropogenic and biogenic emissions, and therefore their accurate representation in models is important for effective air quality management. Despite considerable progress, mechanistic understanding of some key aqueous processes is still lacking, and these pathways are incompletely represented in 3D atmospheric chemistry and air quality models. In this article, the concepts, historical context, and current state of the science of aqueous pathways of SOA formation are discussed.

  19. Flexible organic electronic devices: Materials, process and applications

    International Nuclear Information System (INIS)

    Logothetidis, Stergios

    2008-01-01

    The research for the development of flexible organic electronic devices (FEDs) is rapidly increasing worldwide, since FEDs will change radically several aspects of everyday life. Although there has been considerable progress in the area of flexible inorganic devices (a-Si or solution processed Si), there are numerous advances in the organic (semiconducting, conducting and insulating), inorganic and hybrid (organic-inorganic) materials that exhibit customized properties and stability, and in the synthesis and preparation methods, which are characterized by a significant amount of multidisciplinary efforts. Furthermore, the development and encapsulation of organic electronic devices onto flexible polymeric substrates by large-scale and low-cost roll-to-roll production processes will allow their market implementation in numerous application areas, including displays, lighting, photovoltaics, radio-frequency identification circuitry and chemical sensors, as well as to a new generation of modern exotic applications. In this work, we report on some of the latest advances in the fields of polymeric substrates, hybrid barrier layers, inorganic and organic materials to be used as novel active and functional thin films and nanomaterials as well as for the encapsulation of the materials components for the production of FEDs (flexible organic light-emitting diodes, and organic photovoltaics). Moreover, we will emphasize on the real-time optical monitoring and characterization of the growing films onto the flexible polymeric substrates by spectroscopic ellipsometry methods. Finally, the potentiality for the in-line characterization processes for the development of organic electronics materials will be emphasized, since it will also establish the framework for the achievement of the future scientific and technological breakthroughs

  20. Study of the radiosterilization dose effect on properties of poly(ethylene terephthalate) - PET recycled

    International Nuclear Information System (INIS)

    Isoldi, Ana Beatriz Godoy; Silva, Leonardo Gondim de Andrade e; Rosario, Salmo Cordeiro do

    2002-01-01

    The packing are in constant development, in function, especially, the process of globalization. The opening of the brazilian market after currency stabilization, caused technological innovations, change of habits and costumes of the population and environmental matters. Year after year, because of cost reductions, it became more extreme the hard study of the polymeric materials and their copolymers, their possible blends and their recycling, always seeking a better wrapping of the products, especially when it concerns to the food, increasing its shelf life. The process of sterilization of foods and modification of polymers through radiation are targets of growing interest by of the current industries linked to the nutrition and packing sectors. The objective of this paper is to discuss the application of the radiation (electron beam) in the sterilization of packings of recycled poly(ethylene terephthalate) PET, evaluating the possible effects on their properties. (author)

  1. Knowledge Management Enablers and Process in Hospital Organizations.

    Science.gov (United States)

    Lee, Hyun-Sook

    2017-02-01

    This research aimed to investigate the effects of knowledge management enablers, such as organizational structure, leadership, learning, information technology systems, trust, and collaboration, on the knowledge management process of creation, storage, sharing, and application. Using data from self-administered questionnaires in four Korean tertiary hospitals, this survey investigated the main organizational factors affecting the knowledge management process in these organizations. A total of 779 questionnaires were analyzed using SPSS 18.0 and AMOS 18.0. The results showed that organizational factors affect the knowledge management process differently in each hospital organization. From a managerial perspective, the implications of these factors for developing organizational strategies that encourage and foster the knowledge management process are discussed.

  2. Secondary organic aerosol formation through cloud processing of aromatic VOCs

    Science.gov (United States)

    Herckes, P.; Hutchings, J. W.; Ervens, B.

    2010-12-01

    Field observations have shown substantial concentrations (20-5,500 ng L-1) of aromatic volatile organic compounds (VOC) in cloud droplets. The potential generation of secondary organic aerosol mass through the processing of these anthropogenic VOCs was investigated through laboratory and modeling studies. Under simulated atmospheric laboratory conditions, in idealized solutions, benzene, toluene, ethylbenzene, and xylene (BTEX) degraded quickly in the aqueous phase. The degradation process yielded less volatile products which would contribute to new aerosol mass upon cloud evaporation. However, when realistic cloud solutions containing natural organic matter were used in the experiments, the reaction rates decreased with increasing organic carbon content. Kinetic data derived from these experiments were used as input to a multiphase box model in order to evaluate the secondary organic aerosol (SOA) mass formation potential of cloud processing of BTEX. Model results will be presented that quantify the SOA amounts from these aqueous phase pathways. The efficiency of this multiphase SOA source will be compared to SOA yields from the same aromatics as treated in traditional SOA models that are restricted to gas phase oxidation and subsequent condensation on particles.

  3. Effect of electron beam radio-sterilization on cyclo olefin copolymers and its impact on the interactions with other active molecules

    International Nuclear Information System (INIS)

    Barakat, H.

    2013-01-01

    The aim of this work was to study the effect of electron beam radio-sterilization on cyclo olefins copolymers (COC) used as pharmaceutical storage materials, as well as to investigate its impact on the interaction with pharmaceuticals formulations. Due to the analytical methodology used which has dealt with different techniques of characterization such as size exclusion chromatography, reversed phase high performance liquid chromatography, Fourier transformed infrared spectroscopy, atomic force microscopy and contact angle measurements, we have been able to put into evidence different kinds of modifications both in the bulk and on the surface of the sterilized material and also after ageing. The principal modification of material's bulk, observed at the recommended dose for sterilization (25 kGy), was polymer chains scissions, accompanied with creation of low molecular weight compounds, that are potentials migrants that are likely to affect the safe use of COC. Indeed, some of these compounds have been found with a relatively important concentration in the solutions where sterilized COC has been stored, especially in aqueous solutions. However, the preliminary study of toxicity has shown the absence of cytotoxicity of the extractable by-products obtained at the sterilization dose. Surface modifications of radio-sterilized COC are of two types: a physical one, with an increase of the surface's roughness and a chemical one with the formation of polar oxidation products; these two modifications result in an increase of surface's wettability that may be important. However, in some cases such as for aged samples, these modifications are relatively weak even at doses higher than the one recommended for sterilization, which can explain the absence of the effect of radiation on the behavior of COC concerning drug solutions. Indeed, no variation of drug sorption has been observed between irradiated aged COC and no-irradiated aged COC. (author)

  4. Improving processes in financial service organizations: where to begin?

    NARCIS (Netherlands)

    Lokkerbol, J.; Does, R.J.M.M.; de Mast, J.; Schoonhoven, M.

    2012-01-01

    Purpose - The purpose of this paper is to create actionable knowledge, thereby supporting and stimulating practitioners to improve processes in the financial services sector. Design/methodology/approach - This paper is based on a case base of improvement projects in financial service organizations.

  5. Diversity attitudes and group knowledge processing in multicultural organizations

    DEFF Research Database (Denmark)

    Lauring, Jakob; Selmer, Jan

    2013-01-01

    The ability to locate, share, and use knowledge is vital for effective functioning of organizations. However, such knowledge processing can be complicated by increasing cultural diversity. Recent studies have suggested that a group’s diversity attitudes may increase group outcomes. In this study...... diversity only had a positive effect on personal knowledge....

  6. All-solution processed organic solar cells with top illumination

    NARCIS (Netherlands)

    Patil, B.R.; Shanmugam, S.; Teunissen, J.P.; Galagan, Y.

    2015-01-01

    All-solution processed organic solar cells with inverted device architecture were demonstrated. Devices contain opaque bottom electrodes and semitransparent top electrodes, resulting in top illuminated devices. Nanoparticles-based Ag ink was used for inkjet printing both top and bottom electrodes.

  7. All-solution-processed organic solar cells with conventional architecture

    NARCIS (Netherlands)

    Franeker, J.J. van; Voorthuijzen, W.P.; Gorter, H.; Hendriks, K.H.; Janssen, R.A.J.; Hadipour, A.; Andriessen, H.A.J.M.; Galagan, Y.O.

    2013-01-01

    Abstract All-solution processed organic solar cells with a conventional device structure were demonstrated. The evaporated low work function LiF/Al electrode was replaced by a printed high work function silver electrode combined with an additional electron transport layer (ETL). Two electron

  8. All-solution-processed organic solar cells with conventional architecture

    NARCIS (Netherlands)

    Franeker, van J.J.; Voorthuijzen, W.P.; Gorter, H.; Hendriks, K.H.; Janssen, R.A.J.; Hadipour, A.; Andriessen, R.; Galagan, Y.

    2013-01-01

    All-solution processed organic solar cells with a conventional device structure were demonstrated. The evaporated low work function LiF/Al electrode was replaced by a printed high work function silver electrode combined with an additional electron transport layer (ETL). Two electron transport layers

  9. Changes in Actin Organization During the Cytotoxic Process

    NARCIS (Netherlands)

    Radosevic, K.; Radosevic, Katarina; van Leeuwen, Anne Marie T.; Segers-Nolten, Gezina M.J.; Figdor, Carl; de Grooth, B.G.; Greve, Jan

    1994-01-01

    Changes in organization of F-actin during the cytotoxic process between NK and K562 cells have been observed and studied using confpcal laser scanning microscopy and quantitative fluorescence microscopy. An increase in F-actin content and orientation of F-actin towards the target cell have been

  10. Prioritizing substitution of organic solvents in industrial cleaning processes

    DEFF Research Database (Denmark)

    Rasmussen, Pia Brunn; Jacobsen, Thomas

    1997-01-01

    A method for prioritizing the substitution of volatile organic compounds (VOC) used in industrial cleaning processes is developed. The result is a matrix, which, if all information can be obtained, gives a comprehensive description of the effects, exposure and emission of VOC, as well as the pros...

  11. Treating contaminated organic compounds using the DETOX process

    International Nuclear Information System (INIS)

    Elsberry, K.; Dhooge, P.M.

    1993-01-01

    Waste matrices containing organic compounds, radionuclides, and metals pose difficult problems in waste treatment and disposal when the organic compounds and/or metals are considered to be hazardous. This paper describes the results of bench-scale studies of DETOX applied to the components of liquid mixed wastes, with the goal of establishing parameters for designing a prototype waste treatment unit. Apparent reaction rate orders for organic compounds and the dependence of apparent reaction rate on solution composition and the contact area were measured for vacuum pump oil, scintillation fluids, and trichloroethylene. Reaction rate was superior in chloride-based solutions and was proportional to the contact area above about 20 g/kg loading of organic material. Oxidations in 4-L volume, mixed bench-top reactor have given destruction efficiencies of 0.999999+ g/g for common organic compounds. Reaction rates achieved in the mixed bench-top reactor were one to two orders of magnitude greater than had been achieved in unmixed reactions; a thoroughly mixed reactor should be capable of oxidizing 10 to 100+ g of organic material per L-hr. Results are also presented on the solvation efficiency of DETOX for mercury, cerium, and neodymium, and for removal/destruction of organic compounds sorbed on vermiculite. The next stage of development will be converting the bench-top unit to continuous processing

  12. The Exnovation of Chronic Care Management Processes by Physician Organizations.

    Science.gov (United States)

    Rodriguez, Hector P; Henke, Rachel Mosher; Bibi, Salma; Ramsay, Patricia P; Shortell, Stephen M

    2016-09-01

    Policy Points The rate of adoption of chronic care management processes (CMPs) by physician organizations has been fairly slow in spite of demonstrated effectiveness of CMPs in improving outcomes of chronic care. Exnovation (ie, removal of innovations) by physician organizations largely explains the slow population-level increases in practice use of CMPs over time. Expanded health information technology functions may aid practices in retaining CMPs. Low provider reimbursement by Medicaid programs, however, may contribute to disinvestment in CMPs by physician organizations. Exnovation is the process of removal of innovations that are not effective in improving organizational performance, are too disruptive to routine operations, or do not fit well with the existing organizational strategy, incentives, structure, and/or culture. Exnovation may contribute to the low overall adoption of care management processes (CMPs) by US physician organizations over time. Three national surveys of US physician organizations, which included common questions about organizational characteristics, use of CMPs, and health information technology (HIT) capabilities for practices of all sizes, and Truven Health Insurance Coverage Estimates were integrated to assess organizational and market influences on the exnovation of CMPs in a longitudinal cohort of 1,048 physician organizations. CMPs included 5 strategies for each of 4 chronic conditions (diabetes, asthma, congestive heart failure, and depression): registry use, nurse care management, patient reminders for preventive and care management services to prevent exacerbations of chronic illness, use of nonphysician clinicians to provide patient education, and quality of care feedback to physicians. Over one-third (34.1%) of physician organizations exnovated CMPs on net. Quality of care data feedback to physicians and patient reminders for recommended preventive and chronic care were discontinued by over one-third of exnovators, while nurse

  13. The Exnovation of Chronic Care Management Processes by Physician Organizations

    Science.gov (United States)

    HENKE, RACHEL MOSHER; BIBI, SALMA; RAMSAY, PATRICIA P.; SHORTELL, STEPHEN M.

    2016-01-01

    Policy Points The rate of adoption of chronic care management processes (CMPs) by physician organizations has been fairly slow in spite of demonstrated effectiveness of CMPs in improving outcomes of chronic care.Exnovation (ie, removal of innovations) by physician organizations largely explains the slow population‐level increases in practice use of CMPs over time.Expanded health information technology functions may aid practices in retaining CMPs. Low provider reimbursement by Medicaid programs, however, may contribute to disinvestment in CMPs by physician organizations. Context Exnovation is the process of removal of innovations that are not effective in improving organizational performance, are too disruptive to routine operations, or do not fit well with the existing organizational strategy, incentives, structure, and/or culture. Exnovation may contribute to the low overall adoption of care management processes (CMPs) by US physician organizations over time. Methods Three national surveys of US physician organizations, which included common questions about organizational characteristics, use of CMPs, and health information technology (HIT) capabilities for practices of all sizes, and Truven Health Insurance Coverage Estimates were integrated to assess organizational and market influences on the exnovation of CMPs in a longitudinal cohort of 1,048 physician organizations. CMPs included 5 strategies for each of 4 chronic conditions (diabetes, asthma, congestive heart failure, and depression): registry use, nurse care management, patient reminders for preventive and care management services to prevent exacerbations of chronic illness, use of nonphysician clinicians to provide patient education, and quality of care feedback to physicians. Findings Over one‐third (34.1%) of physician organizations exnovated CMPs on net. Quality of care data feedback to physicians and patient reminders for recommended preventive and chronic care were discontinued by over one

  14. Becoming a Learning Organization Through Dynamic Business Process Management

    Directory of Open Access Journals (Sweden)

    Marek Szelągowski

    2014-01-01

    Full Text Available As customers demand easier access to individualized products and services, companies now face an ongoing problem of how to deliver flexible and innovative solutions while maintaining efficiency and competitiveness. In this environment, the only sustainable form of competitive advantage rests in the ability to learn faster than the competition (de Geus, 1988. The article returns to the somewhat forgotten concept of the learning organization and explores how its principles can be applied with the use of dynamic business process management (dynamic BPM. Enabling in this concept individual or team-based limited experimentation and providing conditions for learning though experience in the course of performing business processes allows for the constant creation of practical knowledge. This article provides examples of how dynamic BPM facilitates the constant creation and verification of practical knowledge, with the aim of improving and adapting processes to maintain the competitive advantage of the organization.

  15. Work within the coordinated programme on radiosterilization of medical and biomedical products

    International Nuclear Information System (INIS)

    Rhee, K.S.

    1978-03-01

    From surgical silk suture a radio-resistent microorganism was isolated and identified as Micrococcus roseus. It was not inactivated completely at radiation doses of 2.3 Mrad. The microorganisms originated from the raw materials of the surgical silk suture. The radiosensitivity of Micrococcus roseus in various environments was studied from 2.0 to 3.4 Mrad. The radioresistance was enhanced if the silk suture extract was used as a liquid media, indicating the presence of a radioprotective agent. The microorganism showed an increased radiosensitivity in oxygen bubbling conditions. Dextrose solution and physiological saline showed a decrease in pH and the presence of some unknown material. There indications, that the substances produced by radiolysis are different depending on the sterilization process applied. The antibiotic activities were stable for 10 Mrad at dry state. The activity was lost at low doses in liquid state except for neomycin which showed a tenfold increase in antibiotic activity. To evaluate the toxicity of irradiated transfusion sets a more detailed study is required

  16. Radiosterilization of historical documents: the potential effects of gamma irradiation on paper and printing inks

    Energy Technology Data Exchange (ETDEWEB)

    Jesus, Anderson G. de, E-mail: jesus.anderson@aman.eb.mil.br [Academia Militar das Agulhas Negras (AMAN/EB), Resende, RJ (Brazil); Brandã, Luis E.B.; Salgado, César M., E-mail: brandao@ien.gov.br, E-mail: otero@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

    2017-07-01

    The controlled exposition to gamma radiation is a physical process which can be used for the preservation and recovery of historical documents. Depending on the intrinsic characteristics of the material to be treated, it is necessary to research and establish, from time to time, the optimum dose rate and total dose, the conditions to eliminate or reduce the biological threat, the equipment and its logistics, the economic aspects and any other impact caused by radiation on the material to be treated. The references indicate that through research it is possible to consolidate the knowledge about gamma radiation emitted from {sup 60}Co in order to completely remove or at least greatly reduce infestation by insects or biodeterioration microorganisms. On this work we have used a MDS Nordion self-contained {sup 60}Co research irradiator, model Gamacell Excel 220, at Postgraduate Institute of Engineering and Research Alberto Luiz Coimbra, in Rio de Janeiro Federal University. The analysis of the samples submitted to controlled thermal dry aging and to gamma radiation made possible to verify the differences between treated and untreated samples. The results of the chromatic measures indicate that, with the optimum total dose, the gamma radiation treatment does not significantly alter the properties of paper or printing inks. This way, it is possible to conclude that even though the gamma irradiation of historical documents is a complex procedure which demands a detailed study in order to assure its safe application, it is environmentally safer than the use of chemical pesticides. (author)

  17. Radiosterilization of historical documents: the potential effects of gamma irradiation on paper and printing inks

    International Nuclear Information System (INIS)

    Jesus, Anderson G. de; Brandã, Luis E.B.; Salgado, César M.

    2017-01-01

    The controlled exposition to gamma radiation is a physical process which can be used for the preservation and recovery of historical documents. Depending on the intrinsic characteristics of the material to be treated, it is necessary to research and establish, from time to time, the optimum dose rate and total dose, the conditions to eliminate or reduce the biological threat, the equipment and its logistics, the economic aspects and any other impact caused by radiation on the material to be treated. The references indicate that through research it is possible to consolidate the knowledge about gamma radiation emitted from 60 Co in order to completely remove or at least greatly reduce infestation by insects or biodeterioration microorganisms. On this work we have used a MDS Nordion self-contained 60 Co research irradiator, model Gamacell Excel 220, at Postgraduate Institute of Engineering and Research Alberto Luiz Coimbra, in Rio de Janeiro Federal University. The analysis of the samples submitted to controlled thermal dry aging and to gamma radiation made possible to verify the differences between treated and untreated samples. The results of the chromatic measures indicate that, with the optimum total dose, the gamma radiation treatment does not significantly alter the properties of paper or printing inks. This way, it is possible to conclude that even though the gamma irradiation of historical documents is a complex procedure which demands a detailed study in order to assure its safe application, it is environmentally safer than the use of chemical pesticides. (author)

  18. CONVERSION PRODUCT STRUCTURE AS TOOL TO INCREASE YIELD PROCESSING ORGANIZATIONS

    Directory of Open Access Journals (Sweden)

    A. I. Khorev

    2014-01-01

    Full Text Available The authors' analysis of the performance of organizations, processing raw materials of agricultural origin, in particular, dealing with meat processing, identified the need to develop tools to increase their profitability. Unlike common approaches to assessing the profitability of the processing organizations, taking into account only the interests of the organization's leadership and buyers of products, the authors proposed and implemented a concept based on the interests of participants in the triune balance business activities: owners of capital, management organizations and consumers. As one of the tools for improving the yield of processing organizations are invited to transform their product mix of economic evaluations of profitability of each product line positions. Russian researchers income from product sales are traditionally measured by indicators such as net income, income from sales, profit margins and profitability level - in terms of return on sales. The disadvantage of using these indicators, according to the authors, is their lack of objectivity in the evaluation of the effectiveness of investment business owners. In this work was used unconventional and non-proliferation in the Russian practice, the rate of economic value added (EVA, a built - in system of profitability assortment positions. As indicators, the production of a particular product line units proposed and used two quantitative indicators - EVA level per unit of production and profitability of production (for EVA, as well as a quality parameter - the level of demand. Developed by the evaluation program transformation product structure represented as a matrix management capabilities, allowing to achieve a balance of interests of the triune main participants in business activity.

  19. Origin of poor doping efficiency in solution processed organic semiconductors.

    Science.gov (United States)

    Jha, Ajay; Duan, Hong-Guang; Tiwari, Vandana; Thorwart, Michael; Miller, R J Dwayne

    2018-05-21

    Doping is an extremely important process where intentional insertion of impurities in semiconductors controls their electronic properties. In organic semiconductors, one of the convenient, but inefficient, ways of doping is the spin casting of a precursor mixture of components in solution, followed by solvent evaporation. Active control over this process holds the key to significant improvements over current poor doping efficiencies. Yet, an optimized control can only come from a detailed understanding of electronic interactions responsible for the low doping efficiencies. Here, we use two-dimensional nonlinear optical spectroscopy to examine these interactions in the course of the doping process by probing the solution mixture of doped organic semiconductors. A dopant accepts an electron from the semiconductor and the two ions form a duplex of interacting charges known as ion-pair complexes. Well-resolved off-diagonal peaks in the two-dimensional spectra clearly demonstrate the electronic connectivity among the ions in solution. This electronic interaction represents a well resolved electrostatically bound state, as opposed to a random distribution of ions. We developed a theoretical model to recover the experimental data, which reveals an unexpectedly strong electronic coupling of ∼250 cm -1 with an intermolecular distance of ∼4.5 Å between ions in solution, which is approximately the expected distance in processed films. The fact that this relationship persists from solution to the processed film gives direct evidence that Coulomb interactions are retained from the precursor solution to the processed films. This memory effect renders the charge carriers equally bound also in the film and, hence, results in poor doping efficiencies. This new insight will help pave the way towards rational tailoring of the electronic interactions to improve doping efficiencies in processed organic semiconductor thin films.

  20. Alternatives to Organic Solvents in Industrial Cleaning Processes

    DEFF Research Database (Denmark)

    Jacobsen, Thomas

    1998-01-01

    To control chemical hazards in work places, substitution of harmful substances with less harmful or non-toxic products is now a method used in many countries and in many companies. It has previously been demonstrated that it is desirable and possible to use non-volatile, low-toxic vegetable...... cleaning agents in offset printing companies instead of volatile, toxic organic solvents. The present study is based on a project with the aim of defining other industrial processes, where organic solvents used for cleaning or degreasing can be replaced by non-volatile, low-toxic products, which are based...... on esters from fatty acids of vegetable origin (vegetable esters - VE).The study indicates that industrial cleaning/degreasing with organic solvents may be substituted with VEs on metal surfaces and on some coated surfaces, in manufacture of paints and inks, use of paints, use of inks (printing), metal...

  1. Misfits in Organization Design: Information Processing as a Compensatory Mechanism

    Directory of Open Access Journals (Sweden)

    Ben Nanfeng Luo

    2013-04-01

    Full Text Available We propose a compensatory misfits theory which holds that an “over-fitting” organization structure can compensate for an “under-fitting” structure, thereby reducing the total misfit. In organizations, over-fit occurs when structural features misfit the core contingencies because the structural level is too high to fit the contingencies. An under-fit occurs when structural features misfit the contingencies because the structural level is too low. When an under-fit is compensated by an over-fit, the combination can produce performance outcomes that approximate those from fit. The reason inheres in information processing being a higher level factor that cuts across different contingencies and structural features that are mis-fitted to each other, so that compensation is possible. We identify the specific conditions that must be fulfilled for compensation to occur, and we discuss implications for organization design theory and practice.

  2. Theoretical insights into multiscale electronic processes in organic photovoltaics

    Science.gov (United States)

    Tretiak, Sergei

    Present day electronic devices are enabled by design and implementation of precise interfaces that control the flow of charge carriers. This requires robust and predictive multiscale approaches for theoretical description of underlining complex phenomena. Combined with thorough experimental studies such approaches provide a reliable estimate of physical properties of nanostructured materials and enable a rational design of devices. From this perspective I will discuss first principle modeling of small-molecule bulk-heterojunction organic solar cells and push-pull chromophores for tunable-color organic light emitters. The emphasis is on electronic processes involving intra- and intermolecular energy or charge transfer driven by strong electron-phonon coupling inherent to pi-conjugated systems. Finally I will describe how precise manipulation and control of organic-organic interfaces in a photovoltaic device can increase its power conversion efficiency by 2-5 times in a model bilayer system. Applications of these design principles to practical architectures like bulk heterojunction devices lead to an enhancement in power conversion efficiency from 4.0% to 7.0%. These interface manipulation strategies are universally applicable to any donor-acceptor interface, making them both fundamentally interesting and technologically important for achieving high efficiency organic electronic devices.

  3. Practical process research and development a guide for organic chemists

    CERN Document Server

    Anderson, Neal G

    2014-01-01

    Designed to provide a comprehensive, step-by-step approach to organic process research and development in the pharmaceutical, fine chemical, and agricultural chemical industries, this book describes the steps taken, following synthesis and evaluation, to bring key compounds to market in a cost-effective manner. It describes hands-on, step-by-step, approaches to solving process development problems, including route, reagent, and solvent selection; optimising catalytic reactions; chiral syntheses; and ""green chemistry."" Second Edition highlights:  Reflects the current thinking in chemical p

  4. Procesna organiziranost in zadovoljstvo zaposlenih = Process Organization and Employee Satisfaction

    Directory of Open Access Journals (Sweden)

    Karmen Verle

    2010-06-01

    Full Text Available The purpose of the paper is to show the influence of process organizationon employee satisfaction and to indicate the directions for improvingthe operations success in the chosen company. A quantitativeresearch has been carried out for this purpose with the help of astandardized questionnaire for measuring the organizational climateon the census of 556 employed co-workers. The key finding leads tothe recognition that the analyzed company supposedly places greatemphasis also on the modern - process organization. With the latter,employee motivation and innovation are increased, which is consequentlyshown in greater operations success of the discussed company.With the correlation coefficient we establish that the dimension of theorganization statistically positively influences employee satisfaction(0.461, which means that the form and method of the organization caninfluence employee satisfaction. The results of the research have theoreticaland practical benefits for the management in planning, carryingout and controlling of business processes and it will be possible to implementthem in profitable and non-profitable organizations.

  5. Microgravity Processing and Photonic Applications of Organic and Polymeric Materials

    Science.gov (United States)

    Frazier, Donald 0; Penn, Benjamin G.; Smith, David; Witherow, William K.; Paley, M. S.; Abdeldayem, Hossin A.

    1998-01-01

    In recent years, a great deal of interest has been directed toward the use of organic materials in the development of high-efficiency optoelectronic and photonic devices. There is a myriad of possibilities among organic which allow flexibility in the design of unique structures with a variety of functional groups. The use of nonlinear optical (NLO) organic materials such as thin-film waveguides allows full exploitation of their desirable qualities by permitting long interaction lengths and large susceptibilities allowing modest power input. There are several methods in use to prepare thin films, such as Langmuir-Blodgett (LB) and self-assembly techniques, vapor deposition, growth from sheared solution or melt, and melt growth between glass plates. Organics have many features that make Abstract: them desirable for use in optical devices such as high second- and third-order nonlinearities, flexibility of molecular design, and damage resistance to optical radiation. However, their use in devices has been hindered by processing difficulties for crystals and thin films. In this chapter, we discuss photonic and optoelectronic applications of a few organic materials and the potential role of microgravity on processing these materials. It is of interest to note how materials with second- and third-order nonlinear optical behavior may be improved in a diffusion-limited environment and ways in which convection may be detrimental to these materials. We focus our discussion on third-order materials for all-optical switching, and second-order materials for all-optical switching, and second-order materials for frequency conversion and electrooptics.

  6. Intermediate organizations in the innovation process in Mexico

    Directory of Open Access Journals (Sweden)

    Maria del Pilar Monserrat Pérez Hernández

    2016-07-01

    Full Text Available The innovation activity depends strongly on the interaction between generating actors and end-users of new knowledge and technologies. There are several intermediate organizations (IO that facilitate translating the needs of the users with the new technologies that are beingdeveloped, in order to satisfy more effectively their demands. This paper analyzes the mediation process involved in the IO in innovative activity in Mexico, to identify structural holes in the innovation process. The relevant results in the Mexican intermediation process points that threeimportant structural holes of the process are missing: one between the negotiation process and sponsorship, the second in marketing and commercial profit of the obtained results and the last one in the regulation and referring activities. It is very important that the detected missinglinks in the intermediation process are filled, because they can hinder considerably the overall profit and benefits that society could obtained of the innovation process.

  7. Organic photovoltaic cells: from performance improvement to manufacturing processes.

    Science.gov (United States)

    Youn, Hongseok; Park, Hui Joon; Guo, L Jay

    2015-05-20

    Organic photovoltaics (OPVs) have been pursued as a next generation power source due to their light weight, thin, flexible, and simple fabrication advantages. Improvements in OPV efficiency have attracted great attention in the past decade. Because the functional layers in OPVs can be dissolved in common solvents, they can be manufactured by eco-friendly and scalable printing or coating technologies. In this review article, the focus is on recent efforts to control nanomorphologies of photoactive layer and discussion of various solution-processed charge transport and extraction materials, to maximize the performance of OPV cells. Next, recent works on printing and coating technologies for OPVs to realize solution processing are reviewed. The review concludes with a discussion of recent advances in the development of non-traditional lamination and transfer method towards highly efficient and fully solution-processed OPV. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Impact of fog processing on water soluble organic aerosols.

    Science.gov (United States)

    Tripathi, S. N.; Chakraborty, A.; Gupta, T.

    2017-12-01

    Fog is a natural meteorological phenomenon that occurs all around the world, and contains a substantial quantity of liquid water. Fog is generally seen as a natural cleansing agent but can also form secondary organic aerosols (SOA) via aqueous processing of ambient organics. Few field studies have reported elevated O/C ratio and SOA mass during or after fog events. However, mechanism behind aqueous SOA formation and its contribution to total organic aerosols (OA) still remains unclear. In this study we have tried to explore the impact of fog/aqueous processing on the characteristics of water soluble organic aerosols (WSOC), which to our knowledge has not been studied before. To assess this, both online (using HR-ToF-AMS) and offline (using a medium volume PM2.5 sampler and quartz filter) aerosol sampling were carried out at Kanpur, India from 15 December 2014 - 10 February 2015. Further, offline analysis of the aqueous extracts of the collected filters were carried out by AMS to characterize the water soluble OA (WSOA). Several (17) fog events occurred during the campaign and high concentrations of OA (151 ± 68 µg/m3) and WSOA (47 ± 19 µg/m3) were observed. WSOA/OA ratios were similar during fog (0.36 ± 0.14) and nofog (0.34 ± 0.15) periods. WSOA concentrations were also similar (slightly higher) during foggy (49 ± 18 µg/m3) and non-foggy periods (46 ± 20 µg/m3), in spite of fog scavenging. However, WSOA was more oxidized during foggy period (average O/C = 0.81) than non foggy periods (average O/C = 0.70). Like WSOA, OA was also more oxidized during foggy periods (average O/C = 0.64) than non foggy periods (average O/C = 0.53). During fog, WSOA to WIOA (water insoluble OA) ratios were higher (0.65 ± 0.16) compared to non foggy periods (0.56 ± 0.15). These observations clearly showed that WSOA become more dominant and processed during fog events, possibly due to the presence of fog droplets. This study highlights that fog processing of soluble organics

  9. Organic pollutant removal from edible oil process wastewater using electrocoagulation

    Science.gov (United States)

    Sharma, S.; Can, O. T.; Hammed, M.; Nawarathna, D.; Simsek, H.

    2018-03-01

    Wastewaters generated from vegetable oil industries contain a high concentration of organic pollutants that are detrimental to the aquatic ecosystem. Electrochemical processes are gaining importance in the treatment of inorganic and resistant organic pollutants in wastewaters. In this study, electrocoagulation (EC) was applied to remove organic pollutants and oil and grease from canola oil wastewater using aluminum (Al) and iron (Fe) electrodes. The application of EC in the wastewater achieved more than 80% removal of organic carbon and nearly 100% removal of suspended solids (SS). The effectiveness of EC is influenced mainly by current density, pH, electrolyte (NaCl), electrode contact time and electrode type. It was observed that Al electrode combination yielded better removal at a lesser time compared to that of Fe electrodes. However, varying current densities had its significance in terms of coagulation time only. Increase in current density achieved decrease in coagulation time. Both Al and Fe could remove between 52-59% of oil and grease from canola oil wastewater

  10. Morin-based nanofiltration membranes for organic solvent separation processes

    KAUST Repository

    Perez Manriquez, Liliana

    2018-02-26

    In this work we demonstrate the successful optimization of the interfacial polymerization reaction for the manufacture of organic solvent nanofiltration membranes by replacing the toxic amines commonly used for this method with the natural occurring bio-polyphenol morin. For the manufacture of this type of OSN membrane a crosslinked PAN support was coated by interfacial polymerization using morin as the monomer of the aqueous phase and terephtaloyl chloride as the monomer of the organic phase. These membranes showed an exceptional performance and resistance to NMP by having a a permeance of 0.3L/m2 h bar in NMP with a rejection of 96% of Brilliant Blue dye which has a molecular weight of 825.97g/mol, making these membranes attractive for harsh industrial separation processes due to their ease of manufacture, low cost, and excellent performance.

  11. Aqueous processing of organic compounds in carbonaceous asteroids

    Science.gov (United States)

    Trigo-Rodríguez, Josep Maria; Rimola, Albert; Martins, Zita

    2015-04-01

    There is growing evidence pointing towards a prebiotic synthesis of complex organic species in water-rich undifferentiated bodies. For instance, clays have been found to be associated with complex organic compounds (Pearson et al. 2002; Garvie & Buseck 2007; Arteaga et al. 2010), whereas theoretical calculations have studied the interaction between the organic species and surface minerals (Rimola et al., 2013) as well as surface-induced reactions (Rimola at al. 2007). Now, we are using more detailed analytical techniques to study the possible processing of organic molecules associated with the mild aqueous alteration in CR, CM and CI chondrites. To learn more about these processes we are studying carbonaceous chondrites at Ultra High-Resolution Transmission Electron Microscopy (UHR-TEM). We are particularly interested in the relationship between organics and clay minerals in carbonaceous chondrites (CCs) matrixes (Trigo-Rodríguez et al. 2014, 2015).We want to address two goals: i) identifying the chemical steps in which the organic molecules could have increased their complexity (i.e., surface interaction and catalysis); and ii) studying if the organic matter present in CCs experienced significant processing concomitant to the formation of clays and other minerals at the time in which these planetary bodies experienced aqueous alteration. Here, these two points are preliminarily explored combing experimental results with theoretical calculations based on accurate quantum mechanical methods. References Arteaga O, Canillas A, Crusats J, El-Hachemi Z, Jellison GE, Llorca J, Ribó JM (2010) Chiral biases in solids by effect of shear gradients: a speculation on the deterministic origin of biological homochirality. Orig Life Evol Biosph 40:27-40. Garvie LAJ, Buseck PR (2007) Prebiotic carbon in clays from Orgueil and Ivuna (CI) and Tagish lake (C2 ungrouped) meteorites. Meteorit Planet Sci 42:2111-2117. Pearson VK, Sephton MA, Kearsley AT, Bland AP, Franchi IA, Gilmour

  12. Microgravity Processing and Photonic Applications of Organic and Polymeric Materials

    Science.gov (United States)

    Frazier, Donald O.; Paley, Mark S.; Penn, Benjamin G.; Abdeldayem, Hossin A.; Smith, David D.; Witherow, William K.

    1997-01-01

    Some of the primary purposes of this work are to study important technologies, particularly involving thin films, relevant to organic and polymeric materials for improving applicability to optical circuitry and devices and to assess the contribution of convection on film quality in unit and microgravity environments. Among the most important materials processing techniques of interest in this work are solution-based and by physical vapor transport, both having proven gravitational and acceleration dependence. In particular, PolyDiAcetylenes (PDA's) and PhthaloCyanines (Pc's) are excellent NonLinear Optical (NLO) materials with the promise of significantly improved NLO properties through order and film quality enhancements possible through microgravity processing. Our approach is to focus research on integrated optical circuits and optoelectronic devices relevant to solution-based and vapor processes of interest in the Space Sciences Laboratory at the Marshall Space Flight Center (MSFC). Modification of organic materials is an important aspect of achieving more highly ordered structures in conjunction with microgravity processing. Parallel activities include characterization of materials for particular NLO properties and determination of appropriation device designs consistent with selected applications. One result of this work is the determination, theoretically, that buoyancy-driven convection occurs at low pressures in an ideal gas in a thermalgradient from source to sink. Subsequent experiment supports the theory. We have also determined theoretically that buoyancy-driven convection occurs during photodeposition of PDA, an MSFC-patented process for fabricating complex circuits, which is also supported by experiment. Finally, the discovery of intrinsic optical bistability in metal-free Pc films enables the possibility of the development of logic gate technology on the basis of these materials.

  13. Optimal integration of organic Rankine cycles with industrial processes

    International Nuclear Information System (INIS)

    Hipólito-Valencia, Brígido J.; Rubio-Castro, Eusiel; Ponce-Ortega, José M.; Serna-González, Medardo; Nápoles-Rivera, Fabricio; El-Halwagi, Mahmoud M.

    2013-01-01

    Highlights: • An optimization approach for heat integration is proposed. • A new general superstructure for heat integration is proposed. • Heat process streams are simultaneously integrated with an organic Rankine cycle. • Better results can be obtained respect to other previously reported methodologies. - Abstract: This paper presents a procedure for simultaneously handling the problem of optimal integration of regenerative organic Rankine cycles (ORCs) with overall processes. ORCs may allow the recovery of an important fraction of the low-temperature process excess heat (i.e., waste heat from industrial processes) in the form of mechanical energy. An integrated stagewise superstructure is proposed for representing the interconnections and interactions between the HEN and ORC for fixed data of process streams. Based on the integrated superstructure, the optimization problem is formulated as a mixed integer nonlinear programming problem to simultaneously account for the capital and operating costs including the revenue from the sale of the shaft power produced by the integrated system. The application of this method is illustrated with three example problems. Results show that the proposed procedure provides significantly better results than an earlier developed method for discovering optimal integrated systems using a sequential approach, due to the fact that it accounts simultaneously for the tradeoffs between the capital and operating costs as well as the sale of the produced energy. Also, the proposed method is an improvement over the previously reported methods for solving the synthesis problem of heat exchanger networks without the option of integration with an ORC (i.e., stand-alone heat exchanger networks)

  14. Secondary organic aerosol formation through fog processing of VOCs

    Science.gov (United States)

    Herckes, P.; Hutchings, J. W.

    2010-07-01

    Volatile Organic Compounds (VOCs) including benzene, toluene, ethylbenzene and xylenes (BTEX) have been determined in highly concentrated amounts (>1 ug/L) in intercepted clouds in northern Arizona (USA). These VOCs are found in concentrations much higher than predicted by partitioning alone. The reactivity of BTEX in the fog/cloud aqueous phase was investigated through laboratory studies. BTEX species showed fast degradation in the aqueous phase in the presence of peroxides and light. Observed half-lives ranged from three and six hours, substantially shorter than the respective gas phase half-lives (several days). The observed reaction rates were on the order of 1 ppb/min but decreased substantially with increasing concentrations of organic matter (TOC). The products of BTEX oxidation reactions were analyzed using HPLC-UV and LCMS. The first generation of products identified included phenol and cresols which correspond to the hydroxyl-addition reaction to benzene and toluene. Upon investigating of multi-generational products, smaller, less volatile species are predominant although a large variety of products is found. Most reaction products have substantially lower vapor pressure and will remain in the particle phase upon droplet evaporation. The SOA generation potential of cloud and fog processing of BTEX was evaluated using simple calculations and showed that in ideal situations these reactions could add up to 9% of the ambient aerosol mass. In more conservative scenarios, the contribution of the processing of BTEX was around 1% of ambient aerosol concentrations. Overall, cloud processing of VOC has the potential to contribute to the atmospheric aerosol mass. However, the contribution will depend upon many factors such as the irradiation, organic matter content in the droplets and droplet lifetime.

  15. Cloud processing of organic compounds: Secondary organic aerosol and nitrosamine formation

    Science.gov (United States)

    Hutchings, James W., III

    Cloud processing of atmospheric organic compounds has been investigated through field studies, laboratory experiments, and numerical modeling. Observational cloud chemistry studies were performed in northern Arizona and fog studies in central Pennsylvania. At both locations, the cloud and fogs showed low acidity due to neutralization by soil dust components (Arizona) and ammonia (Pennsylvania). The field observations showed substantial concentrations (20-5500 ng•L -1) of volatile organic compounds (VOC) in the cloud droplets. The potential generation of secondary organic aerosol mass through the processing of these anthropogenic VOCs was investigated through laboratory and modeling studies. Under simulated atmospheric conditions, in idealized solutions, benzene, toluene, ethylbenzene, and xylene (BTEX) degraded quickly in the aqueous phase with half lives of approximately three hours. The degradation process yielded less volatile products which would contribute to new aerosol mass upon cloud evaporation. However, when realistic cloud solutions containing natural organic matter were used in the experiments, the reaction kinetics decreased with increasing organic carbon content, resulting in half lives of approximately 7 hours. The secondary organic aerosol (SUA) mass formation potential of cloud processing of BTEX was evaluated. SOA mass formation by cloud processing of BTEX, while strongly dependent on the atmospheric conditions, could contribute up to 9% of the ambient atmospheric aerosol mass, although typically ˜1% appears realistic. Field observations also showed the occurrence of N-nitrosodimethylamine (NDMA), a potent carcinogen, in fogs and clouds (100-340 ng•L -1). Laboratory studies were conducted to investigate the formation of NDMA from nitrous acid and dimethylamine in the homogeneous aqueous phase within cloud droplets. While NDMA was produced in the cloud droplets, the low yields (NDMA with partitioning to droplet must be the source of aqueous

  16. Freshwater processing of terrestrial dissolved organic matter: What governs lability?

    Science.gov (United States)

    D'Andrilli, J.; Smith, H. J.; Junker, J. R.; Scholl, E. A.; Foreman, C. M.

    2016-12-01

    Aquatic and terrestrial ecosystems are linked through the transfer of energy and materials. Allochthonous organic matter (OM) is central to freshwater ecosystem function, influencing local food webs, trophic state, and nutrient availability. In order to understand the nature and fate of OM from inland headwaters to the open ocean, it is imperative to understand the links between OM lability and ecosystem function. Thus, biological, chemical, and physical factors need to be evaluated together to inform our understanding of environmental lability. We performed a laboratory processing experiment on naturally occurring OM leachates from riparian leaves, grasses, and pine needles. Measures of water chemistry, OM optical and molecular characterization, bacterial abundances, microbial assemblage composition, respiration, and C:N:P were integrated to discern the nature and fate of labile and recalcitrant OM in a freshwater stream. Peak processing of all OM sources in the stream water occurred after two days, with spikes in bacterial cell abundances, respiration rates, microbial assemblage shifts, and maximum C utilization. Respiration rates and microbial assemblages were dependent on the degree of lability of the OM molecular composition. Within the first few days, no differences in respiration rates were observed between leachate sources, however, beyond day five, the rates diverged with C processing efficiency correlated with OM lability. Originally comprised of amino acid-like, labile fluorescent species, the inoculated stream water OM became more recalcitrant after 16 days, indicating humification processing over time. Our study highlights the importance of interdisciplinary approaches for understanding the processing and fate of OM in aquatic ecosystems.

  17. [Automation and organization of technological process of urinalysis].

    Science.gov (United States)

    Kolenkin, S M; Kishkun, A A; Kol'chenko, O L

    2000-12-01

    Results of introduction into practice of a working model of industrial technology of laboratory studies and KONE Specific Supra and Miditron M devices are shown as exemplified by clinical analysis of the urine. This technology helps standardize all stages and operations, improves the efficiency of quality control of laboratory studies, rationally organizes the work at all stages of the process, creates a system for permanent improvement of the efficiency of investigations at the preanalytical, analytical, and postanalytical stages of technological process of laboratory studies. As a result of introduction of this technology into laboratory practice, violations of quality criteria of clinical urinalysis decreased from 15 to 8% at the preanalytical stage and from 6 to 3% at the analytical stage. Automation of the analysis decreased the need in reagents 3-fold and improved the productivity at the analytical stage 4-fold.

  18. Destruction and formation of organic micropollutants in incineration process

    International Nuclear Information System (INIS)

    Mascolo, G.; Bagnuolo, G.; Lotito, V.; Spinosa, L.; Mininni, G.

    2001-01-01

    In this paper are presented the results obtained from a lab-scale investigation carried out with a system for Thermal Diagnostic Studies (STDS) aimed to study the effect of some process variables during incineration. The study has been focused on (I) gas phase dioxins formation during precursors thermal degradation, (II) thermal degradation of toxic organic compounds, (III) products of incomplete combustion (PICs) formation during thermal degradation of urban sludge spiked with toxic organics, (IV) PICs formation during process failure modes, (V) polynuclear aromatic hydrocarbons (PAHs) formation during urban sludge thermal degradation and (VI) influence of conditioning polymer on PICs emission during sludge incineration. The study about gas phase dioxins formation during precursors thermal degradation has been carried out with 2, 4, 6-trichloro- and 2, 4, 6 -tribromo-phenol that were thermal degraded at temperatures between 300 and 800 0 C in an air atmosphere. Both phenols showed the formation of the same tetra-halo-dioxin isomers that were further degraded at higher temperature. Furthermore, chlorine-containing dioxins showed higher thermal stability than bromine-containing dioxins. The study about thermal degradation of toxic organic compounds has been carried out with chlorobenzene, tetrachloroethylene and toluene that were thermal degraded at temperatures between 300 and 1000 0 C in an inert as well as air atmosphere. Results show that in all experimental conditions tetrachloroethylene and toluene are the most and less thermal stable compounds respectively. Also, all compounds are more thermal resistant during pyrolytic experiments and less thermal resistant when they are treated as a whole mixture. The study about PICs formation during thermal degradation of urban sludge spiked with toxic organics has been carried out by thermally degrading urban sludge alone or spiked with the above reported three organics at different conditions of temperature and oxygen

  19. Solution processed organic bulk heterojunction tandem solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Albrecht, Steve; Neher, Dieter [Soft Matter Physics, University of Potsdam, D-14476 Potsdam (Germany)

    2011-07-01

    One of the critical issues regarding the preparation of organic tandem solar cells from solution is the central recombination contact. This contact should be highly transparent and conductive to provide high recombination currents. Moreover it should protect the 1st subcell from the solution processing of the 2nd subcell. Here, we present a systematic study of various recombination contacts in organic bulk heterojunction tandem solar cells made from blends of different polymers with PCBM. We compare solution processed recombination contacts fabricated from metal-oxides (TiO{sub 2} and ZnO) and PEDOT:PSS with evaporated recombination contacts made from thin metal layers and molybdenum-oxide. The solar cell characteristics as well as the morphology of the contacts measured by AFM and SEM are illustrated. To compare the electrical properties of the varying contacts we show measurements on single carrier devices for different contact-structures. Alongside we present the results of optical modeling of the subcells and the complete tandem device and relate these results to experimental absorption and reflection spectra of the same structures. Based on these studies, layer thicknesses were adjusted for optimum current matching and device performance.

  20. Process relevant screening of cellulolytic organisms for consolidated bioprocessing.

    Science.gov (United States)

    Antonov, Elena; Schlembach, Ivan; Regestein, Lars; Rosenbaum, Miriam A; Büchs, Jochen

    2017-01-01

    Although the biocatalytic conversion of cellulosic biomass could replace fossil oil for the production of various compounds, it is often not economically viable due to the high costs of cellulolytic enzymes. One possibility to reduce costs is consolidated bioprocessing (CBP), integrating cellulase production, hydrolysis of cellulose, and the fermentation of the released sugars to the desired product into one process step. To establish such a process, the most suitable cellulase-producing organism has to be identified. Thereby, it is crucial to evaluate the candidates under target process conditions. In this work, the chosen model process was the conversion of cellulose to the platform chemical itaconic acid by a mixed culture of a cellulolytic fungus with Aspergillus terreus as itaconic acid producer. Various cellulase producers were analyzed by the introduced freeze assay that measures the initial carbon release rate, quantifying initial cellulase activity under target process conditions. Promising candidates were then characterized online by monitoring their respiration activity metabolizing cellulose to assess the growth and enzyme production dynamics. The screening of five different cellulase producers with the freeze assay identified Trichoderma   reesei and Penicillium   verruculosum as most promising. The measurement of the respiration activity revealed a retarded induction of cellulase production for P.   verruculosum but a similar cellulase production rate afterwards, compared to T.   reesei . The freeze assay measurement depicted that P.   verruculosum reaches the highest initial carbon release rate among all investigated cellulase producers. After a modification of the cultivation procedure, these results were confirmed by the respiration activity measurement. To compare both methods, a correlation between the measured respiration activity and the initial carbon release rate of the freeze assay was introduced. The analysis revealed that the

  1. Solution processed metal oxide thin film hole transport layers for high performance organic solar cells

    Science.gov (United States)

    Steirer, K. Xerxes; Berry, Joseph J.; Chesin, Jordan P.; Lloyd, Matthew T.; Widjonarko, Nicodemus Edwin; Miedaner, Alexander; Curtis, Calvin J.; Ginley, David S.; Olson, Dana C.

    2017-01-10

    A method for the application of solution processed metal oxide hole transport layers in organic photovoltaic devices and related organic electronics devices is disclosed. The metal oxide may be derived from a metal-organic precursor enabling solution processing of an amorphous, p-type metal oxide. An organic photovoltaic device having solution processed, metal oxide, thin-film hole transport layer.

  2. Neoliberalist influences on nursing hospital work process and organization.

    Science.gov (United States)

    Souza, Norma Valéria Dantas de Oliveira; Gonçalves, Francisco Gleidson de Azevedo; Pires, Ariane da Silva; David, Helena Maria Scherlowski Leal

    2017-01-01

    To describe and analyze the influence of the neoliberal economic and political model on the nursing hospital work process and organization. Qualitative descriptive research, having as its scenery a university hospital. The subjects were 34 nursing workers. The data collection took place from March to July 2013, through semi-structured interview. The data treatment technique used was content analysis, which brought up the following category: working conditions precariousness and its consequences to the hospital work process and organization in the neoliberal context. The consequences of neoliberalism on hospital work process and organization were highlighted, being observed physical structure, human resources and material inadequacies that harms the assistance quality. In addition to wage decrease that cause the need of second jobs and work overload. There is a significant influence of the neoliberal model on hospital work, resulting on working conditions precariousness. Descrever e analisar a influência do modelo econômico e político neoliberal na organização e no processo de trabalho hospitalar de enfermagem. Pesquisa qualitativa e descritiva, tendo como cenário um hospital universitário. Os participantes foram 34 trabalhadores de enfermagem. A coleta ocorreu de março a julho de 2013, por meio de entrevista semiestruturada. A técnica de tratamento dos dados foi a análise de conteúdo, que fez emergir a seguinte categoria: precarização das condições laborais e suas repercussões para organização e processo de trabalho hospitalar no contexto neoliberal. Evidenciaram-se repercussões do neoliberalismo na organização e no processo de trabalho hospitalar, verificando-se inadequações na estrutura física, nos recursos humanos e materiais, que afetavam a qualidade da assistência. Além de perdas salariais que levam à necessidade de outros empregos e sobrecarga de trabalho. Há forte influência do modelo neoliberal no trabalho hospitalar, resultando

  3. The reduction of population of cabbage pests plutela maculipennis curtis and crocidolomia binotalis zell as affected by the release of radiosterilized moths

    International Nuclear Information System (INIS)

    Hoedaya, M.S.; Sutrisno, S.; Nasroh, A.; Sastradihardja, S.I.

    1983-01-01

    Moths of plutella maculipennis curtis and crocidolimia binotalis zell radiosterilized with 30 Krad and 40 Krad of gamma radiation respectively were released into a laboratory-cage of 90 cm x 60 cm x 60 cm, a field-cage of 2 m x 2 m x 2 m and an experimental plot of 10 m x 15 m to study their effect on the reduction of F1-population. The release of 450 irradiated moths in the laboratory-cage containing 50 unirradiated moths can reduce the F1-population of plutella maculipennis and crocidolomia binotalis by 61.1% and 65.3% respectively. While in the field-cage the F1-population of plutella maculipennis and crocidolomia binotalis decreased by 55.6% and 50.55% respectively. The release of about 4.500 irradiated crocidolomia binotalis into an experimental plot containing 500 normal moths can reduce the F1-population by 41.02% in the dry season and 50.55% in the rainy season. The release of about 5.000 irradiated moths of plutella maculipennis into an experimental plot containing about 350 moths of natural population, resulted in a reduction of egg hatch from 85.9% in the unreleased plot to 17.0% in the released plot. (author)

  4. Reduction of population of cabbage pests plutela maculipennis curtis and crocidolomia binotalis zell as affected by the release of radiosterilized moths

    Energy Technology Data Exchange (ETDEWEB)

    Hoedaya, M.S.; Sutrisno, S.; Nasroh, A.; Sastradihardja, S.I. (National Atomic Energy Agency, Jakarta (Indonesia). Pasar Djumat Research Centre)

    1983-10-01

    Moths of plutella maculipennis curtis and crocidolimia binotalis zell radiosterilized with 30 Krad and 40 Krad of gamma radiation respectively were released into a laboratory-cage of 90 cm x 60 cm x 60 cm, a field-cage of 2 m x 2 m x 2 m and an experimental plot of 10 m x 15 m to study their effect on the reduction of F1-population. The release of 450 irradiated moths in the laboratory-cage containing 50 unirradiated moths can reduce the F1-population of plutella maculipennis and crocidolomia binotalis by 61.1% and 65.3% respectively, while in the field-cage the F1-population of plutella maculipennis and crocidolomia binotalis decreased by 55.6% and 50.55% respectively. The release of about 4,500 irradiated crocidolomia binotalis into an experimental plot containing 500 normal moths can reduce the F1-population by 41.02% in the dry season and 50.55% in the rainy season. The release of about 5,000 irradiated moths of plutella maculipennis into an experimental plot containing about 350 moths of natural population resulted in a reduction of egg hatch from 85.9% in the unreleased plot to 17.0% in the released plot.

  5. Uranium removal from organic solutions of PUREX process

    International Nuclear Information System (INIS)

    Dell'Occhio, L.A.; Dupetit, G.A.; Pascale, A.A.; Vicens, H.E.

    1987-01-01

    During the uranium extraction process with tributyl phosphate (TBP) in nitric medium, a bi solvated, non hydrated complex is formed, of formula UO2(NO3)2TBP, which is soluble in the diluent, a paraffin hydrocarbon. As it is known that some uranium salts, for instance the nitrate, when dissolved in organic solvents, like isopropanol, can be discharged as complex molecules at the cathode of an electrodeposition cell, it was decided to apply this technique to uranium loaded TBP solutions. From preliminary experiments resulted a practical possibility for the analytical control through the alpha measurement of electro deposits. This technique could be applied as well to the treatment of depleted organic streams carrying undesirable alpha activity, because the so treated solutions become deprived of uranium. This work presents the curves obtained working at constant voltage with uranium-loaded TBP solutions, the determination of the optimal operation voltage in these conditions, the electrodeposition yield for electro polished copper and stainless steel cathodes and the tests of reproducibility of deposits. A summary of the results obtained operating the high voltage supply at constant power is also presented. (Author)

  6. Iodine-129 in aquatic organisms near nuclear fuels processing plants

    International Nuclear Information System (INIS)

    Watson, D.G.

    1975-04-01

    Concentrations of 129 I in two aquatic habitats near nuclear fuel processing plants were highest in algae and crustaceans. These two forms may be useful in future monitoring of 129 I. There is some indication of an increase in atom ratios and specific activity in aquatic organisms over that in water and sediments. Additional measurements should be made to verify this conclusion. Efforts should continue to measure the possible long term build-up of 129 I in aquatic environments receiving effluents from fuels reprocessing plants. Even at very low rates of release to the environment, the long physical half-life of 129 I creates the potential for build-up of this nuclide to significant levels. (U.S.)

  7. New Product Fumbles - Organizing for the Ramp-up Process

    DEFF Research Database (Denmark)

    Christensen, Irene

    This study examines rapid prototyping, also referred to as new production launch, or ramp-up time. A strong emphasis on speed is vital for the success of a product development and market launch. Managers concern themselves with organizing ramp-up activities into arrayed sequences to achieve...... production launch goals. These sequences are not only regarding prearranged linear milestones, but extensively reviewed and often reorganized complex activities, with the managerial goal of a wellconfigured productive process. The need to manage the final phase in product development is evident, because many...... of the development of products. This has been achieved by longitudinally studying a total of eight major development cases at a large Scandinavian manufacturing company over a period of three years. These development projects faced different challenges during the interface between R&D and ramp-up production...

  8. Bacteria and fluorescent organic matter: processing and production.

    Science.gov (United States)

    Fox, B. G.; Thorn, R. M. S.; Reynolds, D. M.

    2017-12-01

    There is a need for a greater understanding of the importance of aquatic organic matter (OM) within global biogeochemical cycling. This need has prompted characterisation of OM using fluorescence spectroscopy. The origin, transformation and fate of fluorescent organic matter (FOM) is not fully understood within freshwater systems. This work demonstrates the importance of microbial processing in the creation and transformation of FOM, highlighting the dynamics of microbial-FOM interactions, using a model system. The FOM signature of different bacterial species common to surface freshwaters were analysed using a non-fluorescent media; Escherichia coli, Bacillus subtilis and Pseudomonas aeruginosa. By undertaking bacterial growth curves, alongside fluorescence spectroscopy, we have been able to determine FOM development in relation to population growth. Within this, we have identified that FOM peaks are associated with different species and driven by bacterial processes, such as cell multiplication or as metabolic by-products. The intracellular and extracellular fluorescence signature of each species has also been analysed to better understand how the microbial community structure may impact the FOM signal in aquatic systems. For example, Peak T develops within the growth curves of all the cultured species and has been identified as both intracellular and extracellular FOM. Whilst Peak T has been termed `microbially-derived' previously, other fluorescence peaks associated with terrestrial high molecular weight compounds, e.g. Peak C, have also been shown to be produced by bacteria throughout growth stages. Additionally, the notion that cell lysis is responsible for the presence of larger FOM compounds was also explored. Our work highlights the capacity of bacteria to not only utilise and process OM but to actively be a source of both labile and recalcitrant OM in situ. The bacteria fluorescence signatures seen are complex with comparable fluorescence peaks to those

  9. Energy saving processes for nitrogen removal in organic wastewater from food processing industries in Thailand.

    Science.gov (United States)

    Johansen, N H; Suksawad, N; Balslev, P

    2004-01-01

    Nitrogen removal from organic wastewater is becoming a demand in developed communities. The use of nitrite as intermediate in the treatment of wastewater has been largely ignored, but is actually a relevant energy saving process compared to conventional nitrification/denitrification using nitrate as intermediate. Full-scale results and pilot-scale results using this process are presented. The process needs some additional process considerations and process control to be utilized. Especially under tropical conditions the nitritation process will round easily, and it must be expected that many AS treatment plants in the food industry already produce NO2-N. This uncontrolled nitrogen conversion can be the main cause for sludge bulking problems. It is expected that sludge bulking problems in many cases can be solved just by changing the process control in order to run a more consequent nitritation. Theoretically this process will decrease the oxygen consumption for oxidation by 25% and the use of carbon source for the reduction will be decreased by 40% compared to the conventional process.

  10. Processing of volatile organic compounds by microwave plasmas

    International Nuclear Information System (INIS)

    Mizeraczyk, J.; Jasinski, M.; Dors, M.; Zakrzewski, Z.

    2011-01-01

    In this paper atmospheric pressure microwave discharge methods and devices used for producing the nonthermal plasmas for processing of gases are presented. The main part of the paper concerns the microwave plasma sources (MPSs) for environmental protection applications. A few types of the MPSs, i.e. waveguidebased surface wave sustained MPS, coaxial-line-based and waveguide-based nozzle-type MPSs, waveguidebased nozzleless cylinder-type MPS and MPS for microdischarges are presented. Also, results of the laboratory experiments on the plasma processing of several highly-concentrated (up to several tens percent) volatile organic compounds (VOCs), including Freon-type refrigerants, in the moderate (200-400 W) waveguide-based nozzletype MPS (2.45 GHz) are presented. The results showed that the microwave discharge plasma fully decomposed the VOCs at relatively low energy cost. The energy efficiency of VOCs decomposition reached 1000 g/kWh. This suggests that the microwave discharge plasma can be a useful tool for environmental protection applications. In this paper also results of the use of the waveguide-based nozzleless cylinder-type MPS to methane reforming into hydrogen are presented. (author)

  11. Processing of volatile organic compounds by microwave plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Mizeraczyk, J. [Centre for Plasma and Laser Engineering, Szewalski Institute of Fluid-Flow Machinery, Polish Academy of Sciences, Gdansk (Poland); Department of Marine Electronics, Gdynia Martime University, Gdynia (Poland); Jasinski, M.; Dors, M.; Zakrzewski, Z. [Centre for Plasma and Laser Engineering, Szewalski Institute of Fluid-Flow Machinery, Polish Academy of Sciences, Gdansk (Poland)

    2011-07-01

    In this paper atmospheric pressure microwave discharge methods and devices used for producing the nonthermal plasmas for processing of gases are presented. The main part of the paper concerns the microwave plasma sources (MPSs) for environmental protection applications. A few types of the MPSs, i.e. waveguidebased surface wave sustained MPS, coaxial-line-based and waveguide-based nozzle-type MPSs, waveguidebased nozzleless cylinder-type MPS and MPS for microdischarges are presented. Also, results of the laboratory experiments on the plasma processing of several highly-concentrated (up to several tens percent) volatile organic compounds (VOCs), including Freon-type refrigerants, in the moderate (200-400 W) waveguide-based nozzletype MPS (2.45 GHz) are presented. The results showed that the microwave discharge plasma fully decomposed the VOCs at relatively low energy cost. The energy efficiency of VOCs decomposition reached 1000 g/kWh. This suggests that the microwave discharge plasma can be a useful tool for environmental protection applications. In this paper also results of the use of the waveguide-based nozzleless cylinder-type MPS to methane reforming into hydrogen are presented. (author)

  12. The Training Process of the Organization Development and Training Office

    Science.gov (United States)

    Johnson, Melissa S.

    2004-01-01

    read and summarized to determine the effectiveness of the class and instructor. In addition to the SOAR workshops, I have several projects and daily tasks to complete. Coding training applications, which require me to be familiar with Glenn s budgetary allocations and policies on training, is an ongoing process. It also requires verifying information reported by an employee via her C-478 form, more commonly known as the training application. I am also the point of contact for the Cuyahoga Community College Advising Sessions held here at NASA Glenn which involves coordinating counselors visits with employees schedules. Two databases had to be created. The first database holds information on administrative staff, and the other tracks supervisors training histories. Through these assignments I gained experience in Microsoft Access 2002 and spreadsheet creation, communicating with co-workers, and successfully facilitating a training to serve specific purposes. With trainings and evaluations to assessment them, the Organization Development and Training Office can assure a quality product and continued customer satisfaction.

  13. Soil Organic Matter Erosion by Interrill Processes from Organically and Conventionally farmed Devon Soil

    Science.gov (United States)

    Armstrong, E.; Ling, A.; Kuhn, N. J.

    2012-04-01

    Globally, between 0.57 and 1.33 Pg of soil organic carbon (SOC) may be affected by interrill processes. Also, a significant amount of phosphorus (P) is contained in the surface soil layer transformed by raindrop impact, runoff and crust formation. In the EU, the P content of a crusted (2 mm) surface layer corresponds to 4 to 40 kg ha-1 of P on arable land (1.094 mil km2). Therefore, the role of interrill processes for nutrient cycling and the global carbon cycle requires close attention. Interrill erosion is a complex phenomenon involving the detachment, transport and deposition of soil particles by raindrop impacted flow. Resistance to interrill erosion varies between soils depending on their physical, chemical and mineralogical properties. In addition, significant changes in soil resistance to interrill erosion occur during storms as a result of changes in surface roughness, cohesion and particle size. As a consequence, erosion on interrill areas is selective, moving the most easily detached small and/or light soil particles. This leads to the enrichment of clay, phosphorous (P) and carbon (C). Such enrichment in interrill sediment is well documented, however, the role of interrill erosion processes on the enrichment remains unclear. Enrichment of P and C in interrill sediment is attributed to the preferential erosion of the smaller, lighter soil particles. In this study, the P and organic C content of sediment generated from two Devon silts under conventional (CS) and organic (OS) soil management were examined. Artificial rainfall was applied to the soils using two rainfall scenarios of differing intensity and kinetic energy to determine the effects on the P and C enrichment in interrill sediment. Interrill soil erodibility was lower on the OS, irrespective of rainfall intensity. Sediment from both soils showed a significant enrichment in P and C compared to the bulk soil. However, sediment from the OS displayed a much greater degree of P enrichment. This shows

  14. [Management of human resources, materials, and organization processes in radioprotection].

    Science.gov (United States)

    Coppola, V

    1999-06-01

    The radiologist must learn to face daily management responsibilities and therefore he/she needs the relevant knowledge. Aside from the mechanisms of management accounting, which differ only slightly from similar analysis methods used in other centers, the managing radiologist (the person in charge) is directly responsible for planning, organizing, coordinating and controlling radiation protection, a major discipline characterizing diagnostic imaging. We will provide some practical management hints, keeping in mind that radiation protection must not be considered a simple (or annoying) technical task, but rather an extraordinary positive element for the radiologist's cultural differentiation and professional identity. The managing radiologist can use the theory and practice of management techniques successfully applied in business, customizing them to the ethics and economics of health care. Meeting the users' needs must obviously prevail on balancing the budget from both a logical and an accounting viewpoints, since non-profit organizations are involved. In radiological practice, distinguishing the management of human from structural resources (direct funding is not presently available) permits to use internal benchmarking for the former and controlled acquisition and planned replacement of technologies in the latter, obviously after evaluation of specific indicators and according to the relevant laws and technical guidelines. Managing human resources means safeguarding the patient, the operator and the population, which can be achieved or improved using benchmarking in a diagnostic imaging department. The references for best practice will be set per tabulas based on the relevant laws and (inter)national guidelines. The physical-technical and bureaucratic-administrative factors involved will be considered as process indices to evaluate the gap from normal standards. Among the different elements involved in managing structural resources, the appropriate acquisition

  15. Process for iron separation from an organic solution containing uranium

    International Nuclear Information System (INIS)

    Textoris, A.; Lyaudet, G.; Bathelier, A.

    1987-01-01

    Iron is separated from an organic solution of U and Fe in a phosphine oxide and an acid organic phosphorus compound by reaction on oxalic acid or a mixture of sulfuric and phosphoric acid or phosphoric acid. Uranium stays in the initial organic solution and iron is transferred to the aqueous phase [fr

  16. Destruction of nitrates, organics, and ferrocyanides by hydrothermal processing

    International Nuclear Information System (INIS)

    Robinson, J.M.; Foy, B.R.; Dell'Orco, P.C.; Anderson, G.; Archuleta, F.; Atencio, J.; Breshears, D.; Brewer, R.; Eaton, H.; McFarland, R.; McInroy, R.; Reynolds, T.; Sedillo, M.; Wilmanns, E.; Buelow, S.J.

    1993-01-01

    This work targets the remediation of the aqueous mixed wastes stored in the underground tanks at the Department of Energy site in Hanford, Washington via hydrothermal processing. The feasibility of destroying the nitrate, organic, and ferrocyanide components of the wastes under supercritical and near critical conditions (623 degree K to 873 degree K, 22.1 MPa to 103.4 MPa) is addressed. A novel method was developed for determining the solubility of nitrate salts in supercritical water solutions at pressures ranging from 24.8 MPa to 30.3 MPa (3600 psi to 4400 psi) and temperatures from 723 degree K to 798 degree K. Sodium nitrate solubilities ranged from 293 mg/kg at 24.8 MPa and 798 degree K to 1963 mg/kg at 30.3 MPa and 723 degree K. Solubility was found to vary directly with pressure, and inversely with temperature. An empirical relationship was developed for the estimation of sodium nitrate solubility at water densities between 0.08 and 0.16 kg/L and temperatures between 723 degree K and 798 degree K. A small volume batch reactor equipped with optical diagnostics was used to monitor the phase behavior of a diluted variant of a tank 101-SY simulant. Preliminary results suggest that a single phase is formed at 83 MPa at 773 degree K

  17. Drugs affecting prelamin A processing: Effects on heterochromatin organization

    International Nuclear Information System (INIS)

    Mattioli, Elisabetta; Columbaro, Marta; Capanni, Cristina; Santi, Spartaco; Maraldi, Nadir M.; D'Apice, M. Rosaria; Novelli, Giuseppe; Riccio, Massimo; Squarzoni, Stefano; Foisner, Roland; Lattanzi, Giovanna

    2008-01-01

    Increasing interest in drugs acting on prelamin A has derived from the finding of prelamin A involvement in severe laminopathies. Amelioration of the nuclear morphology by inhibitors of prelamin A farnesylation has been widely reported in progeroid laminopathies. We investigated the effects on chromatin organization of two drugs inhibiting prelamin A processing by an ultrastructural and biochemical approach. The farnesyltransferase inhibitor FTI-277 and the non-peptidomimetic drug N-acetyl-S-farnesyl-L-cysteine methylester (AFCMe) were administered to cultured control human fibroblasts for 6 or 18 h. FTI-277 interferes with protein farnesylation causing accumulation of non-farnesylated prelamin A, while AFCMe impairs the last cleavage of the lamin A precursor and is expected to accumulate farnesylated prelamin A. FTI-277 caused redistribution of heterochromatin domains at the nuclear interior, while AFCMe caused loss of heterochromatin domains, increase of nuclear size and nuclear lamina thickening. At the biochemical level, heterochromatin-associated proteins and LAP2α were clustered at the nuclear interior following FTI-277 treatment, while they were unevenly distributed or absent in AFCMe-treated nuclei. The reported effects show that chromatin is an immediate target of FTI-277 and AFCMe and that dramatic remodeling of chromatin domains occurs following treatment with the drugs. These effects appear to depend, at least in part, on the accumulation of prelamin A forms, since impairment of prelamin A accumulation, here obtained by 5-azadeoxycytidine treatment, abolishes the chromatin effects. These results may be used to evaluate downstream effects of FTIs or other prelamin A inhibitors potentially useful for the therapy of laminopathies

  18. Invasive soil organisms and their effects on belowground processes

    Science.gov (United States)

    Erik Lilleskov; Jr. Mac A. Callaham; Richard Pouyat; Jane E. Smith; Michael Castellano; Grizelle Gonzalez; D. Jean Lodge; Rachel Arango; Frederick. Green

    2010-01-01

    Invasive species have a wide range of effects on soils and their inhabitants. By altering soils, through their direct effects on native soil organisms (including plants), and by their interaction with the aboveground environment, invasive soil organisms can have dramatic effects on the environment, the economy and human health. The most widely recognized effects...

  19. Digestibility of organic processed feed ingredients in laying hens

    OpenAIRE

    van Krimpen, M.M.; van Diepen, J.T.M; Reuvekamp, B.F.J.; van Harn, J.

    2011-01-01

    In two experiments, digestibility and nutritive value for laying hens of organically-grown feed raw materials was assessed. Digestibility and metabolisable energy content of the products differed considerably compared to those listed in the CVB Feedstuff Table. Laying hens, organic feed raw materials, digestibility, nutritive value

  20. Morin-based nanofiltration membranes for organic solvent separation processes

    KAUST Repository

    Perez Manriquez, Liliana; Neelakanda, Pradeep; Peinemann, Klaus-Viktor

    2018-01-01

    In this work we demonstrate the successful optimization of the interfacial polymerization reaction for the manufacture of organic solvent nanofiltration membranes by replacing the toxic amines commonly used for this method with the natural occurring

  1. Evaluation of Learning Processes in an Organic Chemistry Course.

    Science.gov (United States)

    Maroto, B.; Camusso, C.; Cividini, M.

    1997-01-01

    Reviews a subjective exercise completed by students at the end of each of six units in an introductory organic chemistry course. Argues that instruction should be shaped by Ausubel's concept of meaningful learning. (DDR)

  2. Entrepreneurial Interest in Product Innovation-based Organic Processed Food in SMEs in Malang, Indonesia

    OpenAIRE

    Sri Muljaningsih

    2015-01-01

    The underlying reason for conducting the study is need for organic processed food. Producing innovative organic processed food is not an easy task since it requires creativity. The statement of the problem is how to create entrepreneurial interest to produce organic processed food. The study is a qualitative study of which purpose is to describe organic processed food SMEs behavior. There are 7 (seven) informants involved in the study. The setting of the study is SMEs in “Lily go to organic G...

  3. 40 CFR 63.494 - Back-end process provisions-residual organic HAP limitations.

    Science.gov (United States)

    2010-07-01

    ... organic HAP limitations. 63.494 Section 63.494 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... § 63.494 Back-end process provisions—residual organic HAP limitations. (a) The monthly weighted average residual organic HAP content of all grades of elastomer processed, measured after the stripping operation...

  4. Doping Polymer Semiconductors by Organic Salts: Toward High-Performance Solution-Processed Organic Field-Effect Transistors.

    Science.gov (United States)

    Hu, Yuanyuan; Rengert, Zachary D; McDowell, Caitlin; Ford, Michael J; Wang, Ming; Karki, Akchheta; Lill, Alexander T; Bazan, Guillermo C; Nguyen, Thuc-Quyen

    2018-04-24

    Solution-processed organic field-effect transistors (OFETs) were fabricated with the addition of an organic salt, trityl tetrakis(pentafluorophenyl)borate (TrTPFB), into thin films of donor-acceptor copolymer semiconductors. The performance of OFETs is significantly enhanced after the organic salt is incorporated. TrTPFB is confirmed to p-dope the organic semiconductors used in this study, and the doping efficiency as well as doping physics was investigated. In addition, systematic electrical and structural characterizations reveal how the doping enhances the performance of OFETs. Furthermore, it is shown that this organic salt doping method is feasible for both p- and n-doping by using different organic salts and, thus, can be utilized to achieve high-performance OFETs and organic complementary circuits.

  5. Organizing for creativity, quality and speed in product creation processes

    NARCIS (Netherlands)

    Eijnatten, van F.M.; Simonse, W.L.

    1999-01-01

    Current research in industrial engineering and management sciences shows that organizational architectures are of critical importance for a better performance of product creation processes in terms of creativity, quality and speed. For many companies, streamlining those processes - including

  6. Knowledge management (KM) processes in organizations theoretical foundations and practice

    CERN Document Server

    McInerney, Claire R

    2011-01-01

    Knowledge Management (KM) is an effort to increase useful knowledge in the organization. It is a natural outgrowth of late twentieth century movements to make organizational management and operations more effective, of higher quality, and more responsive to constituents in a rapidly changing global environment. This document traces the evolution of KM in organizations, summarizing the most influential research and literature in the field. It also presents an overview of selected common and current practices in knowledge management, including the relationship between knowledge management and de

  7. Anomalous relaxation and self-organization in nonequilibrium processes

    International Nuclear Information System (INIS)

    Fatkullin, Ibrahim; Kladko, Konstantin; Mitkov, Igor; Bishop, A. R.

    2001-01-01

    We study thermal relaxation in ordered arrays of coupled nonlinear elements with external driving. We find that our model exhibits dynamic self-organization manifested in a universal stretched-exponential form of relaxation. We identify two types of self-organization, cooperative and anticooperative, which lead to fast and slow relaxation, respectively. We give a qualitative explanation for the behavior of the stretched exponent in different parameter ranges. We emphasize that this is a system exhibiting stretched-exponential relaxation without explicit disorder or frustration

  8. Organic food processing: a framework for concept, starting definitions and evaluation.

    Science.gov (United States)

    Kahl, Johannes; Alborzi, Farnaz; Beck, Alexander; Bügel, Susanne; Busscher, Nicolaas; Geier, Uwe; Matt, Darja; Meischner, Tabea; Paoletti, Flavio; Pehme, Sirli; Ploeger, Angelika; Rembiałkowska, Ewa; Schmid, Otto; Strassner, Carola; Taupier-Letage, Bruno; Załęcka, Aneta

    2014-10-01

    In 2007 EU Regulation (EC) 834/2007 introduced principles and criteria for organic food processing. These regulations have been analysed and discussed in several scientific publications and research project reports. Recently, organic food quality was described by principles, aspects and criteria. These principles from organic agriculture were verified and adapted for organic food processing. Different levels for evaluation were suggested. In another document, underlying paradigms and consumer perception of organic food were reviewed against functional food, resulting in identifying integral product identity as the underlying paradigm and a holistic quality view connected to naturalness as consumers' perception of organic food quality. In a European study, the quality concept was applied to the organic food chain, resulting in a problem, namely that clear principles and related criteria were missing to evaluate processing methods. Therefore the goal of this paper is to describe and discuss the topic of organic food processing to make it operational. A conceptual background for organic food processing is given by verifying the underlying paradigms and principles of organic farming and organic food as well as on organic processing. The proposed definition connects organic processing to related systems such as minimal, sustainable and careful, gentle processing, and describes clear principles and related criteria. Based on food examples, such as milk with different heat treatments, the concept and definitions were verified. Organic processing can be defined by clear paradigms and principles and evaluated according criteria from a multidimensional approach. Further work has to be done on developing indicators and parameters for assessment of organic food quality. © 2013 Society of Chemical Industry.

  9. Self-Organization and Annealed Disorder in a Fracturing Process

    DEFF Research Database (Denmark)

    Caldarelli, Guido; Di Tolla, Francesco; Petri, Alberto

    1996-01-01

    We show that a vectorial model for inhomogeneous elastic media self-organizes under external stress. An onset of crack avalanches of every duration and length scale compatible with the lattice size is observed. The behavior is driven by the introduction of annealed disorder, i.e., by lowering...... condition for reproducing the algebraic distribution of the energy released during cracks formation....

  10. Organization and processes of the BN-600 reactor mounting

    International Nuclear Information System (INIS)

    Dubrovin, E.Z.; Karpenko, V.N.; Takhtaulov, V.M.

    1982-01-01

    Structural peculiarities of the BN-600 reactor plant are considered. Experience of metal structure mounting inside the reactor vessel has been analysed. Recommendations on the improvements on the organization of the thermal mechanical equipment mounting are given. It is concluded that the consideration of these recommendations will permit to reduce expenditures of labour by 10-40% for the mounting

  11. Paper 1: The EUROCAT network--organization and processes

    DEFF Research Database (Denmark)

    Boyd, Patricia A; Haeusler, Martin; Barisic, Ingeborg

    2011-01-01

    . The monitoring of new developments in prenatal diagnosis, medication during pregnancy, use of folic acid, and investigation of clusters and exposures are overseen by working groups responsible for organizing research and producing regular reports. The EUROCAT Web site includes current data on prevalence rates...

  12. 78 FR 56811 - National Organic Program-Sunset Process

    Science.gov (United States)

    2013-09-16

    ... List (Sec. 205.105). Changes to the National List may be requested by any individual or organization... removal of a substance from the National List. What is the importance of submitting public comments to the... proposals for removal of substances leading up to the second public meeting. As discussed in Step 6...

  13. Radiosterilization and other sterilization methods of medical equipment on Kilmer's conference, Brussels, 12-16 June 1993

    International Nuclear Information System (INIS)

    Zagorski, Z.P.

    1993-01-01

    The Johnson and Johnson Co. organized the scientific conference devoted to different aspects and methods of sterilization of medical equipment and materials. A condensed review of the main problems discussed during the conference has been done. Attention has been paid especially on: actual problems with primary infections control, problems of sterilization in pharmacy, hazards problems, investigations and control methods and radiation sterilization. 2 figs

  14. Children's Incidental Memory for Pictures: Item Processing Versus List Organizations.

    Science.gov (United States)

    Ghatala, Elizabeth S.; Levin, Joel R.

    1981-01-01

    Two experiments which tested recall differences among young children indicated: (1) organizational factors, not item processing per se, influenced previously found differences in children's recall of pictures following semantic and physical orienting tasks; and (2) physical orienting tasks may effectively inhibit subjects' processing of words, but…

  15. A Social Information Processing Model of Media Use in Organizations.

    Science.gov (United States)

    Fulk, Janet; And Others

    1987-01-01

    Presents a model to examine how social influence processes affect individuals' attitudes toward communication media and media use behavior, integrating two research areas: media use patterns as the outcome of objectively rational choices and social information processing theory. Asserts (in a synthesis) that media characteristics and attitudes are…

  16. Executable business process modeling as a tool for increasing the understanding of business processes in an organization

    OpenAIRE

    Demir, Ersin

    2014-01-01

    Understanding of business processes is becoming an important key factor for successful businesses and today many organizations are facing the lack of knowledge about the business processes that they are working on. Since the interaction between different business processes and different actors are becoming more common it is not only enough for employees to have knowledge about the business processes that they involve directly, but also they need to know about the other business processes in t...

  17. Production of Valuables Organic Acids from Organic Wastes with Hydrothermal Treatment Process

    Directory of Open Access Journals (Sweden)

    Muhammad Faisal

    2009-06-01

    Full Text Available This article reports production of valuables organic acids from the hydrothermal treatment of representative organic wastes and compounds (i. e. domestic sludge, proteinaceous, cellulosic and plastic wastes with or without oxidant (H2O2. Organic acids such as acetic, formic, propionic, succinic and lactic acids were obtained in significant amounts. At 623 K (16.5 MPa, acetic acid of about 26 mg/g-dry waste fish entrails was obtained. This increased to 42 mg/g dry waste fish entrails in the presence of H2O2. Experiments on glucose to represent cellulosic wastes were also carried out, getting acetic acid of about 29 mg/g-glucose. The study was extended to terephthalic acid and glyceraldehyde, reaction intermediates of hydrothermal treatment of PET plastic wastes and glucose, respectively. Studies on temperature dependence of formation of organic acids showed thermal stability of acetic acid, whereas, formic acid decomposed readily under hydrothermal conditions. In general, results demonstrated that the presence of oxidants favored formation of organic acids with acetic acid being the major product. Keywords: hydrothermal treatment, organic acids, organic wastes, oxidant, supercritical water oxidation

  18. Event processing for business organizing the real-time enterprise

    CERN Document Server

    Luckham, David C

    2011-01-01

    Find out how Events Processing (EP) works and how it can workfor you Business Event Processing: An Introduction and StrategyGuide thoroughly describes what EP is, how to use it, and howit relates to other popular information technology architecturessuch as Service Oriented Architecture. Explains how sense and response architectures are being appliedwith tremendous results to businesses throughout the world andshows businesses how they can get started implementing EPShows how to choose business event processing technology tosuit your specific business needs and how to keep costs of adoptingit

  19. Reverse Osmosis Processing of Organic Model Compounds and Fermentation Broths

    National Research Council Canada - National Science Library

    Diltz, Robert; Henley, Michael V; Marolla, Theodore V; Li, Lixiong

    2006-01-01

    .... The actual fermentation broth obtained from a continuous-flow biohydrogen process was treated by the RO system under the operating conditions similar to those used in the baseline tests, resulting in greater...

  20. Entrepreneurial Interest in Product Innovation-based Organic Processed Food in SMEs in Malang, Indonesia

    Directory of Open Access Journals (Sweden)

    Sri Muljaningsih

    2015-12-01

    Full Text Available The underlying reason for conducting the study is need for organic processed food. Producing innovative organic processed food is not an easy task since it requires creativity. The statement of the problem is how to create entrepreneurial interest to produce organic processed food. The study is a qualitative study of which purpose is to describe organic processed food SMEs behavior. There are 7 (seven informants involved in the study. The setting of the study is SMEs in “Lily go to organic Group” community in Malang, Indonesia. Variables of entrepreneurial interest in organic processed food involve attitude, subjective norms and perceived behavioral control. The findings show that creativity influences entrepreneurial interest in organic processed food and it results in creativity. Creativity is also the result of spiritual entrepreneurship that takes understanding towards organic processed food material into consideration. In addition, Lily Group members also take time, capital, raw materials and marketing into account. Another finding reveals that sincerity and strong determination facilitates organic processed food entrepreneurs to work their best. Such determination needs reinforcement from other related party so that the product is accepted by customers.

  1. Strategies toward High Performance Organic Photovoltaic Cell: Material and Process

    Science.gov (United States)

    Kim, Bong Gi

    The power conversion efficiency of organic photovoltaic (OPV) cells has been rapidly improved during the last few years and currently reaches around 10 %. The performance is evenly governed by absorption, exciton diffusion, exciton dissociation, carrier transfer, and collection efficiencies. Establishing a better understanding of OPV device physics combined with the development of new materials for each executive step contributes to this dramatic improvement. This dissertation focuses mainly on material design and development to correlate the intrinsic properties of organic semiconductors and the OPV performance. The introductory Chapter 1 briefly reviews the motivation of OPV research, its working mechanism, and representative organic materials for OPV application. Chapter 2 discusses the modulation of conjugated polymer's (CP's) absorption behavior and an efficient semi-empirical approach to predict CP's energy levels from its constituent monomers' HOMO/LUMO values. A strong acceptor lowered both the HOMO and LUMO levels of the CP, but the LUMO dropped more rapidly which ultimately produced a narrowed band-gap in the electron donating/accepting alternating copolymer system. In addition, the energy level difference between the CP and the constituent monomers converged to a constant value, providing an energy level prediction tool. Chapter 3 illustrates the systematic investigation on the relationship between the molecular structure of an energy harvesting organic dye and the exciton dissociation efficiency. The study showed that the quantum yield decreased as the exciton binding energy increases, and dipole moment direction should be properly oriented in the dye framework in order to improve photo-current generation when used in a dye sensitized photovoltaic device. Chapter 4 demonstrates the ultrasonic-assisted self-assembly of CPs in solution, rapidly and efficiently. Ultrasonication combined with dipolar media accelerated CP's aggregation, and the effect of CP

  2. Micro-Processes of Employees in a Hybrid Organization

    DEFF Research Database (Denmark)

    Svenningsen, Virginie; Boxenbaum, Eva; Ravasi, Davide

    actors engaged in the energy transition. We draw on the literature on institutional logics and hybrid organizations to examine how employees of this French energy corporation deal with this institutionally complex environment. Our findings point to three strategies that individuals use to cope......The present article examines how employees cope with an organizational setting that is institutionally complex. The empirical setting is a French energy corporation that simultaneously pursues a logic of science and a logic of market through multiple research partnerships with public and private...

  3. Knowledge and process in Whitehead’s philosophy of organism

    Directory of Open Access Journals (Sweden)

    Alfonso Gómez Fernández

    2014-11-01

    Full Text Available The aim of this article is to expound the whiteheadian conception of knowledge as a process. It requires explaining previously the core of his metaphysics, known as the «speculative scheme». All knowledge is essentially a process, not only in a subjective but also in an objective sense, for the British philosopher. Process has to be part of the known object, because sense, relevance and therefore understanding only appear in the process, in creative advance. In accordance with the speculative scheme structure (eternal objects» presupposes a process. The traditional classification of knowledge (sensuous and intellectual ignores the root of all kinds of knowledge: the paradoxical concept of a «non-sensuous perception». This concept emphasizes the «biological» constituent of all act of knowledge, and connects consciousness to reality. Finally I explain the culmination of this gnoseology, known as Reformed Subjectivist Principle. This principle leads to a peculiar realism, far from both Greek and medieval realism and from modern subjectivism likewise.

  4. Strategic-Decision Quality in Public Organizations: An Information Processing Perspective.

    NARCIS (Netherlands)

    B.R.J. George (Bert); S. Desmidt (Sebastian)

    2016-01-01

    textabstractThis study draws on information processing theory to investigate predictors of strategic-decision quality in public organizations. Information processing theory argues that (a) rational planning practices contribute to strategic-decision quality by injecting information into decision

  5. Image processing for medical diagnosis of human organs

    International Nuclear Information System (INIS)

    Tamura, Shin-ichi

    1989-01-01

    The report first describes expectations and needs for diagnostic imaging in the field of clinical medicine, radiation medicine in particular, viewed by the author as an image processing expert working at a medical institute. Then, medical image processing techniques are discussed in relation to advanced information processing techniques that are currently drawing much attention in the field of engineering. Finally, discussion is also made of practical applications of image processing techniques to diagnosis. In the field of clinical diagnosis, advanced equipment such as PACS (picture archiving and communication system) has come into wider use, and efforts have been made to shift from visual examination to more quantitative and objective diagnosis by means of such advanced systems. In clinical medicine, practical, robust systems are more useful than sophisticated ones. It is difficult, though important, to develop completely automatized diagnostic systems. The urgent, realistic goal, therefore, is to develop effective diagnosis support systems. In particular, operation support systems equipped with three-dimensional displays will be very useful. (N.K.)

  6. Why wait? : Organizing integrated processes in cancer care

    NARCIS (Netherlands)

    Leeftink, Anne Greetje

    2017-01-01

    The access to cancer diagnostics and cancer treatment is not the same for all types of cancer patients. Furthermore, the resources involved in these processes are costly and scarce. Long access and waiting times to diagnostics and treatment can cause increased anxiety of patients. The goal of this

  7. Rural Identity In Organic Food Processing - A Sensemaking Perspective

    DEFF Research Database (Denmark)

    Hansen, Mette Weinreich

    2011-01-01

    that the three companies, which are all organic and situated in rural areas are enacting their rural identity in slightly different ways. In recent years, a dairy company in one of the outskirt areas of Denmark has gradually changed its way of making sense of the local attachment to also include local areas...... area on a peninsula. Here the local identity is bound to the farm and the land in a ‘small-box’ identity. Besides the differences, similar aspects in the three companies’ markets are identified. All three companies are mainly dependent on urban markets. They all use branding strategies oriented towards...... urban consumers. The strategy of the dairy is selling authentic local (glocal) products where we ‘know’ the producers. The butcher sells superior international quality products, and the mill sells a product tracked from ‘field to fork’ with reduced food miles and a clear farm profile. It is concluded...

  8. OPEC's [Organization of Petroleum Exporting Countries] learning process

    International Nuclear Information System (INIS)

    Boussena, S.

    1994-01-01

    The new world oil market is distinguished by the level of uncertainty that surrounds trends in the price of crude oil. Although its influence has been diminished, the Organization of Petroleum Exporting Countries (OPEC) remains a key player in this market and it is of interest to try to understand its current behaviour. A review is presented of OPEC market regulation, divergence and convergence around pricing issues, and OPEC's reactions to uncertainty, financing of additional production capacity and external competition, non-OPEC oil, alternative energy sources, and energy conservation. In the long term, OPEC has to choose, with the explicit and implicit accord of its other partners in the oil industry, between a relatively regulated market and a situation of total competition. There is the strong likelihood that in the future OPEC will not accept the role of unique regulator of the market and therefore of residual supplier when supply exceeds demand. 15 refs., 3 figs

  9. Radiation processing and prospects in polymers and organics

    International Nuclear Information System (INIS)

    Betz, N.

    1995-01-01

    Ionizing radiation used for industrial applications in the field of polymers and organics are mainly accelerated electrons. Installations using γ-rays exists but are of higher costs. Well established technologies, with large scale production are linked to crosslinking, curing and sterilization. Electronic devices and resists are products with high added value but low volume production. Though considered as promising, other applications (degradation, polymerization, grafting) have only a small commercial production. Ion beams are not presently used and applications are still on the laboratory scale. Though a lot of work is left to be done, these radiations appear to be a very promising tool especially in the field of membranes. A lot of original applications are expected from the use of accelerated ion beams that will increase greatly in the next years. (author). 31 refs

  10. Evaluation of trace organic contaminants in ultra-pure water production processes by measuring total organic halogen formation potential

    International Nuclear Information System (INIS)

    Urano, Kohei; Iwase, Yoko

    1984-01-01

    A new procedure for the determination of organic substances in water with high accuracy and high sensitivity was proposed, in which a hypochlorite is added to water, and the resultant total amount of organic halogen compounds (TOX formation potential) was measured, and it was applied to the evaluation of trace organic contaminants in ultra-pure water production process. In this investigation, the TOX formation potential of the raw water which was to be used for the ultra-pure water production process, intermediately treated water and ultra-pure water was measured to clarify the behavior of organic substances in the ultra-pure water production process and to demonstrate the usefulness of this procedure to evaluate trace organic contaminants in water. The measurement of TOX formation potential requires no specific technical skill, and only a short time, and gives accurate results, therefore, it is expected that the water quality control in the ultra-pure water production process can be performed more exactly by applying this procedure. (Yoshitake, I.)

  11. The Hierarchical Cortical Organization of Human Speech Processing.

    Science.gov (United States)

    de Heer, Wendy A; Huth, Alexander G; Griffiths, Thomas L; Gallant, Jack L; Theunissen, Frédéric E

    2017-07-05

    Speech comprehension requires that the brain extract semantic meaning from the spectral features represented at the cochlea. To investigate this process, we performed an fMRI experiment in which five men and two women passively listened to several hours of natural narrative speech. We then used voxelwise modeling to predict BOLD responses based on three different feature spaces that represent the spectral, articulatory, and semantic properties of speech. The amount of variance explained by each feature space was then assessed using a separate validation dataset. Because some responses might be explained equally well by more than one feature space, we used a variance partitioning analysis to determine the fraction of the variance that was uniquely explained by each feature space. Consistent with previous studies, we found that speech comprehension involves hierarchical representations starting in primary auditory areas and moving laterally on the temporal lobe: spectral features are found in the core of A1, mixtures of spectral and articulatory in STG, mixtures of articulatory and semantic in STS, and semantic in STS and beyond. Our data also show that both hemispheres are equally and actively involved in speech perception and interpretation. Further, responses as early in the auditory hierarchy as in STS are more correlated with semantic than spectral representations. These results illustrate the importance of using natural speech in neurolinguistic research. Our methodology also provides an efficient way to simultaneously test multiple specific hypotheses about the representations of speech without using block designs and segmented or synthetic speech. SIGNIFICANCE STATEMENT To investigate the processing steps performed by the human brain to transform natural speech sound into meaningful language, we used models based on a hierarchical set of speech features to predict BOLD responses of individual voxels recorded in an fMRI experiment while subjects listened to

  12. Targets, drivers and metrics in software process improvement: results of a survey in a multinational organization

    NARCIS (Netherlands)

    Trienekens, J.J.M.; Kusters, R.J.; Genuchten, van M.J.I.M.; Aerts, H.

    2007-01-01

    This paper reports on a survey amongst software groups in a multinational organization. The survey was initiated by the Software Process Improvement (SPI) Steering Committee of Philips, a committee that monitors the status and quality of software process improvement in the global organization. The

  13. Leading processes of patient care and treatment in hierarchical healthcare organizations in Sweden--process managers' experiences.

    Science.gov (United States)

    Nilsson, Kerstin; Sandoff, Mette

    2015-01-01

    The purpose of this study is to gain better understanding of the roles and functions of process managers by describing Swedish process managers' experiences of leading processes involving patient care and treatment when working in a hierarchical health-care organization. This study is based on an explorative design. The data were gathered from interviews with 12 process managers at three Swedish hospitals. These data underwent qualitative and interpretative analysis with a modified editing style. The process managers' experiences of leading processes in a hierarchical health-care organization are described under three themes: having or not having a mandate, exposure to conflict situations and leading process development. The results indicate a need for clarity regarding process manager's responsibility and work content, which need to be communicated to all managers and staff involved in the patient care and treatment process, irrespective of department. There also needs to be an emphasis on realistic expectations and orientation of the goals that are an intrinsic part of the task of being a process manager. Generalizations from the results of the qualitative interview studies are limited, but a deeper understanding of the phenomenon was reached, which, in turn, can be transferred to similar settings. This study contributes qualitative descriptions of leading care and treatment processes in a functional, hierarchical health-care organization from process managers' experiences, a subject that has not been investigated earlier.

  14. Altered organization of face processing networks in temporal lobe epilepsy

    Science.gov (United States)

    Riley, Jeffrey D.; Fling, Brett W.; Cramer, Steven C.; Lin, Jack J.

    2015-01-01

    SUMMARY Objective Deficits in social cognition are common and significant in people with temporal lobe epilepsy (TLE), but the functional and structural underpinnings remain unclear. The present study investigated how the side of seizure focus impacts face processing networks in temporal lobe epilepsy. Methods We used functional magnetic resonance imaging (fMRI) of a face processing paradigm to identify face responsive regions in 24 individuals with unilateral temporal lobe epilepsy (Left = 15; Right = 9) and 19 healthy controls. fMRI signals of face responsive regions ispilateral and contralateral to the side of seizure onset were delineated in TLE and compared to the healthy controls with right and left side combined. Diffusion tensor images were acquired to investigate structural connectivity between face regions that differed in fMRI signals between the two groups. Results In temporal lobe epilepsy, activation of the cortical face processing networks varied according to side of seizure onset. In temporal lobe epilepsy, the laterality of amygdala activation was shifted to the side contralateral to the seizure focus while controls showed no significant asymmetry. Furthermore, compared to controls, patients with TLE showed decreased activation of the occipital face responsive region in the ipsilateral side and an increased activity of the anterior temporal lobe in the contralateral side to the seizure focus. Probabilistic tractography revealed that the occipital face area and anterior temporal lobe are connected via the inferior longitudinal fasciculus, which in individuals with temporal lobe epilepsy showed reduced integrity. Significance Taken together, these findings suggest that brain function and white matter integrity of networks subserving face processing are impaired on the side of seizure onset, accompanied by altered responses on the side contralateral to the seizure. PMID:25823855

  15. The Analysis of Artificial Retina Organization for Signal Processing

    Institute of Scientific and Technical Information of China (English)

    WEIHui

    2004-01-01

    Machine vision is an active branch of artificial intelligence. An important problem in this area is the trade-off among efficiency, accuracy and computation complexity. The human visual system can keep watchfulness to the perimeter of a viewing field while at the same time focus on the center of the field for fine information processing. This mechanism of appropriate assignment of computing resources can reduce the demand for huge and complex hardware structure. Therefore, the design of a computer model based on the biological visual mechanism is an effective approach to resolve problems in machine vision. In this paper, a multi-layer neural model is developed based on the features of receptive field of ganglion in retina to simulate multi-scale perceptive fields of ganglion cell. The neural model can maintain alert on the outer area of the image while capturing and processing more important information in the central part. It may provide valuable inspiration for the implementation of real-time processing and avoidance of huge computation in machine vision.

  16. Investigation of solid organic waste processing by oxidative pyrolysis

    Science.gov (United States)

    Kolibaba, O. B.; Sokolsky, A. I.; Gabitov, R. N.

    2017-11-01

    A thermal analysis of a mixture of municipal solid waste (MSW) of the average morphological composition and its individual components was carried out in order to develop ways to improve the efficiency of its utilization for energy production in thermal reactors. Experimental studies were performed on a synchronous thermal analyzer NETZSCH STA 449 F3 Jupiter combined with a quadrupole mass spectrometer QMC 403. Based on the results of the experiments, the temperature ranges of the pyrolysis process were determined as well as the rate of decrease of the mass of the sample of solid waste during the drying and oxidative pyrolysis processes, the thermal effects accompanying these processes, as well as the composition and volumes of gases produced during oxidative pyrolysis of solid waste and its components in an atmosphere with oxygen content of 1%, 5%, and 10%. On the basis of experimental data the dependences of the yield of gas on the moisture content of MSW were obtained under different pyrolysis conditions under which a gas of various calorific values was produced.

  17. Controlled Growth of Ultrathin Film of Organic Semiconductors by Balancing the Competitive Processes in Dip-Coating for Organic Transistors.

    Science.gov (United States)

    Wu, Kunjie; Li, Hongwei; Li, Liqiang; Zhang, Suna; Chen, Xiaosong; Xu, Zeyang; Zhang, Xi; Hu, Wenping; Chi, Lifeng; Gao, Xike; Meng, Yancheng

    2016-06-28

    Ultrathin film with thickness below 15 nm of organic semiconductors provides excellent platform for some fundamental research and practical applications in the field of organic electronics. However, it is quite challenging to develop a general principle for the growth of uniform and continuous ultrathin film over large area. Dip-coating is a useful technique to prepare diverse structures of organic semiconductors, but the assembly of organic semiconductors in dip-coating is quite complicated, and there are no reports about the core rules for the growth of ultrathin film via dip-coating until now. In this work, we develop a general strategy for the growth of ultrathin film of organic semiconductor via dip-coating, which provides a relatively facile model to analyze the growth behavior. The balance between the three direct factors (nucleation rate, assembly rate, and recession rate) is the key to determine the growth of ultrathin film. Under the direction of this rule, ultrathin films of four organic semiconductors are obtained. The field-effect transistors constructed on the ultrathin film show good field-effect property. This work provides a general principle and systematic guideline to prepare ultrathin film of organic semiconductors via dip-coating, which would be highly meaningful for organic electronics as well as for the assembly of other materials via solution processes.

  18. Organizations

    DEFF Research Database (Denmark)

    Hatch, Mary Jo

    and considers many more. Mary Jo Hatch introduces the concept of organizations by presenting definitions and ideas drawn from the a variety of subject areas including the physical sciences, economics, sociology, psychology, anthropology, literature, and the visual and performing arts. Drawing on examples from......Most of us recognize that organizations are everywhere. You meet them on every street corner in the form of families and shops, study in them, work for them, buy from them, pay taxes to them. But have you given much thought to where they came from, what they are today, and what they might become...... prehistory and everyday life, from the animal kingdom as well as from business, government, and other formal organizations, Hatch provides a lively and thought provoking introduction to the process of organization....

  19. Solution processed nanogap organic diodes based on liquid crystalline materials

    Science.gov (United States)

    Wang, Yi-Fei; Iino, Hiroaki; Hanna, Jun-ichi

    2017-09-01

    Co-planar nanogap organic diodes were fabricated with smectic liquid crystalline materials of the benzothienobenzothiophene (BTBT) derivative by a spin-coating technique. A high rectification ratio of the order of 106 at ±3 V was achieved when a liquid crystalline material of 2,7-didecyl benzothieno[3,2-b][1]benzothiophene (10-BTBT-10) was used in a device configuration of Al/10-BTBT-10/pentafluorobenzenethiol-treated Au on a glass substrate, which was 4 orders higher than that of the device based on non-liquid crystalline materials of 2,7-dibutyl benzothieno[3,2-b][1]benzothiophene (4-BTBT-4) and BTBT. Similar results were also observed when another liquid crystalline material of ω, ω'-dioctylterthiophene (8-TTP-8) and a non-liquid crystalline material of terthiophene (TTP) were used. These improved rectifications can be ascribed to the self-assembly properties and controllable molecular orientation of liquid crystalline materials, which made uniform perpendicular oriented polycrystalline films favorable for superior charge transport in nano-channels.

  20. Organic Solar Cells: Degradation Processes and Approaches to Enhance Performance

    Energy Technology Data Exchange (ETDEWEB)

    Fungura, Fadzai [Iowa State Univ., Ames, IA (United States)

    2016-12-17

    Intrinsic photodegradation of organic solar cells, theoretically attributed to C-H bond rearrangement/breaking, remains a key commercialization barrier. This work presents, via dark electron paramagnetic resonance (EPR), the first experimental evidence for metastable C dangling bonds (DBs) (g=2.0029±0.0004) formed by blue/UV irradiation of polymer:fullerene blend films in nitrogen. The DB density increased with irradiation and decreased ~4 fold after 2 weeks in the dark. The dark EPR also showed increased densities of other spin-active sites in photodegraded polymer, fullerene, and polymer:fullerene blend films, consistent with broad electronic measurements of fundamental properties, including defect/gap state densities. The EPR enabled identification of defect states, whether in the polymer, fullerene, or at the donor/acceptor (D/A) interface. Importantly, the EPR results indicate that the DBs are at the D/A interface, as they were present only in the blend films. The role of polarons in interface DB formation is also discussed.

  1. Progress in high-efficient solution process organic photovoltaic devices fundamentals, materials, devices and fabrication

    CERN Document Server

    Li, Gang

    2015-01-01

    This book presents an important technique to process organic photovoltaic devices. The basics, materials aspects and manufacturing of photovoltaic devices with solution processing are explained. Solution processable organic solar cells - polymer or solution processable small molecules - have the potential to significantly reduce the costs for solar electricity and energy payback time due to the low material costs for the cells, low cost and fast fabrication processes (ambient, roll-to-roll), high material utilization etc. In addition, organic photovoltaics (OPV) also provides attractive properties like flexibility, colorful displays and transparency which could open new market opportunities. The material and device innovations lead to improved efficiency by 8% for organic photovoltaic solar cells, compared to 4% in 2005. Both academic and industry research have significant interest in the development of this technology. This book gives an overview of the booming technology, focusing on the solution process fo...

  2. Polymerization and processing of organic polymers in a magnetic field

    Energy Technology Data Exchange (ETDEWEB)

    Douglas, E.P. [Los Alamos National Laboratory, NM (United States)

    1995-05-01

    The use of magnetic fields to affect the structure and properties of polymeric materials remains an area of great promise. Liquid crystalline polymers have been actively studied over the past 20 years for use in high performance structural applications. In particular, highly oriented fibers can exhibit remarkable increases in strength to weight performance compared to conventional materials. For example, the fibers marketed by DuPont under the tradename Kevlar are 20 times stronger than steel on an equivalent weight basis. However, larger bulk parts do not exhibit the same increases in strength due to a lack of orientation of the polymer molecules. Magnetic field processing of polymers remains an attractive solution to this problem.

  3. Solution processable organic/inorganic hybrid ultraviolet photovoltaic detector

    Directory of Open Access Journals (Sweden)

    Xiaopeng Guo

    2016-05-01

    Full Text Available Ultraviolet (UV photodetector is a kind of important optoelectronic device which can be widely used in scientific and engineering fields including astronomical research, environmental monitoring, forest-fire prevention, medical analysis, and missile approach warning etc. The development of UV detector is hindered by the acquirement of stable p-type materials, which makes it difficult to realize large array, low-power consumption UV focal plane array (FPA detector. Here, we provide a novel structure (Al/Poly(9,9-di-n-octylfuorenyl-2,7-diyl(PFO/ZnO/ITO to demonstrate the UV photovoltaic (PV response. A rather smooth surface (RMS roughness: 0.28 nm may be reached by solution process, which sheds light on the development of large-array, light-weight and low-cost UV FPA detectors.

  4. RESEARCH OF PROCESS OF FINANCIAL MONITORING ORGANIZING IN BANKS

    Directory of Open Access Journals (Sweden)

    Viktoriia Kovalenko

    2017-03-01

    Full Text Available The article aims to study methods and tools for financial monitoring by banks. It is proved that one of the main global financial problems in recent years is increasing number of cases of banks participating in the money laundering. It causes banks huge losses, undermines the credibility of honest depositors, in addition, circulation of funds like these hurts the national economy. The article is to develop recommendations to improve the effectiveness of financial monitoring in banks. It is proved that the current model of the national financial monitoring system includes the following elements: the purpose of macroeconomic and microeconomic levels; principles; function; facilities; subjects; types of financial monitoring; methods of implementation and regulatory prevue regulation. It is proved that the major problems related to the financial monitoring of banks are the following: lack of legislatively established quality requirements of customer information; persons engaged in legalization of illegal incomes are highly qualified, which greatly facilitates them through the bank of suspicious transactions; the process of settlement bank failure in the conduct of questionable transactions. Keywords: financial monitoring, suspicious transactions, bank, money laundering, financing of terrorism.

  5. Precipitate hydrolysis process for the removal of organic compounds from nuclear waste slurries

    Science.gov (United States)

    Doherty, J.P.; Marek, J.C.

    1987-02-25

    A process for removing organic compounds from a nuclear waste slurry comprising reacting a mixture of radioactive waste precipitate slurry and an acid in the presence of a catalytically effective amount of a copper(II) catalyst whereby the organic compounds in the precipitate slurry are hydrolyzed to form volatile organic compounds which are separated from the reacting mixture. The resulting waste slurry, containing less than 10 percent of the original organic compounds, is subsequently blended with high level radioactive sludge land transferred to a vitrification facility for processing into borosilicate glass for long-term storage. 2 figs., 3 tabs.

  6. Perception Of The Nurse In The Process Of Donation Of Organs And Fabrics For Transplantation

    Directory of Open Access Journals (Sweden)

    Vanessa Vargas

    2017-06-01

    Full Text Available Objective: to know the nurses' perception in the process of organ and tissue donation for transplants. Methods: qualitative research with data collection performed through a semistructured interview with 16 nurses from a hospital. The data were submitted to Bardin content analysis. Results: categories emerged after content analysis were as follows: Organ donation process: nurses' experience; Nursing care for potential donors; Family approach; Main difficulties in the donation process. Conclusion: the research demonstrated the real difficulties of the professionals during the donation process, such as lack of human resources, extensive protocols, and lack of awareness of the society to understand the donation process and the family approach. Keywords: Transplantation of Organs; Obtaining Tissues and Organs; Nursing care.

  7. Experience of nurses in the process of donation of organs and tissues for transplant.

    Science.gov (United States)

    de Moraes, Edvaldo Leal; dos Santos, Marcelo José; Merighi, Miriam Aparecida Barbosa; Massarollo, Maria Cristina Komatsu Braga

    2014-01-01

    to investigate the meaning of the action of nurses in the donation process to maintain the viability of organs and tissues for transplantation. this qualitative study with a social phenomenological approach was conducted through individual interviews with ten nurses of three Organ and Tissue Procurement Services of the city of São Paulo. the experience of the nurses in the donation process was represented by the categories: obstacles experienced in the donation process, and interventions performed. The meaning of the action to maintain the viability of organs and tissues for transplantation was described by the categories: to change paradigms, to humanize the donation process, to expand the donation, and to save lives. knowledge of the experience of the nurses in this process is important for healthcare professionals who work in different realities, indicating strategies to optimize the procurement of organs and tissues for transplantation.

  8. Experience of nurses in the process of donation of organs and tissues for transplant

    Directory of Open Access Journals (Sweden)

    Edvaldo Leal de Moraes

    2014-04-01

    Full Text Available OBJECTIVE: to investigate the meaning of the action of nurses in the donation process to maintain the viability of organs and tissues for transplantation.METHOD: this qualitative study with a social phenomenological approach was conducted through individual interviews with ten nurses of three Organ and Tissue Procurement Services of the city of São Paulo.RESULTS: the experience of the nurses in the donation process was represented by the categories: obstacles experienced in the donation process, and interventions performed. The meaning of the action to maintain the viability of organs and tissues for transplantation was described by the categories: to change paradigms, to humanize the donation process, to expand the donation, and to save lives.FINAL CONSIDERATIONS: knowledge of the experience of the nurses in this process is important for healthcare professionals who work in different realities, indicating strategies to optimize the procurement of organs and tissues for transplantation.

  9. Relevant Factors for Implementation of Operational-level IS/ICT Processes in Small IT Organizations

    Directory of Open Access Journals (Sweden)

    Jaroslav Kalina

    2010-10-01

    Full Text Available Having IS/ICT processes compliant according to well known standards like COBIT or ITIL is relatively popular especially among larger organizations (to which these standard are primarily aimed. This paper discusses how standardization of processes affects or is affected by a selected set of process characteristics and tries to provide general guidelines which should be considered prior to their implementation (standards. Special attention is paid to the specifics of small IS/ICT organizations since implementation of these frameworks (intended for rather larger organizations represents in this context more demanding endeavor.

  10. Solution processing of back electrodes for organic solar cells with inverted architecture

    NARCIS (Netherlands)

    Galagan, Y.; Shanmugam, S.; Teunissen, J.P.; Eggenhuisen, T.M.; Biezemans, A.F.K.V.; Van Gijseghem, T.; Groen, W.A.; Andriessen, R.

    2014-01-01

    Solution processing of the electrodes is a big challenge towards scaling up and R2R processing of organic solar cells. Inkjet printing is a non-contact printing method, it can be realized by solution processing at ambient condition and provides freedom of shape in the electrode pattern. The inkjet

  11. [Lean thinking and brain-dead patient assistance in the organ donation process].

    Science.gov (United States)

    Pestana, Aline Lima; dos Santos, José Luís Guedes; Erdmann, Rolf Hermann; da Silva, Elza Lima; Erdmann, Alacoque Lorenzini

    2013-02-01

    Organ donation is a complex process that challenges health system professionals and managers. This study aimed to introduce a theoretical model to organize brain-dead patient assistance and the organ donation process guided by the main lean thinking ideas, which enable production improvement through planning cycles and the development of a proper environment for successful implementation. Lean thinking may make the process of organ donation more effective and efficient and may contribute to improvements in information systematization and professional qualifications for excellence of assistance. The model is configured as a reference that is available for validation and implementation by health and nursing professionals and managers in the management of potential organ donors after brain death assistance and subsequent transplantation demands.

  12. Applicability of MIEX(®)DOC process for organics removal from NOM laden water.

    Science.gov (United States)

    Karpinska, Anna M; Boaventura, Rui A R; Vilar, Vítor J P; Bilyk, Andrzej; Molczan, Marek

    2013-06-01

    The aim of this study was to evaluate applicability of ion exchange process for organics removal from Douro River surface water at the intake of Lever water treatment plant using magnetized ion exchange resin MIEX®. Qualitative analysis of the natural organic matter present in the surface water and prediction of its amenability to removal in conventional coagulation process were assessed. Results obtained in MIEX®DOC process kinetic batch experiments allowed determination of ion exchange efficiency in dissolved organic carbon (DOC), UV absorbing organics, and true color removal. The data were compared with the efficiencies of the conventional unit processes for organics removal at Lever WTP. MIEX®DOC process revealed to be more efficient in DOC removal than conventional treatment achieving the efficiencies in the range of 61-91 %, lowering disinfection by-products formation potential of the water. DOC removal efficiency at Lever WTP depends largely on the raw water quality and ranges from 28 % for water of moderated quality to 89 % of significantly deteriorated quality. In this work, MIEX®DOC process was also used as a reference method for the determination of contribution of anionic fraction to dissolved organic matter and selectivity of the unit processes at Lever WTP for its removal.

  13. Underlying principles and actual problems for the processing of organic meat products

    OpenAIRE

    Nielsen, Thorkild

    2004-01-01

    The processing of meat products is regulated by a wide range of different national standards and regulations. Some countries have very strict regulations on additives for organic meat products. Standard setting often involves a balance between maintaining the purity and integrity of the organic system and ensuring that certain quality demands are met. Especially for meat this dilemma has been clearly recognized. Currently the most urgent challenge for the organic meat sector is to offer ...

  14. Organization of educational process as a part of the information environment of the university

    Directory of Open Access Journals (Sweden)

    Оksana S. Savelyeva

    2015-06-01

    Full Text Available The questions concerning the insurance of openness and transparency of the educational process, monitoring the provision of educational services and the quality of learning within a unified information environment of Odessa National Polytechnic University are considered. It is proposed to consider the organization of the educational process as a major component of the educational process, that is a system of activities covering the distribution of the academic load between departments, recruitment of teachers, the formation of class schedules, consultation, final control and state certification. The analysis and the forming of set of parameters are carried out, the main components of the functional subsystem "The organization of educational process" as one of the components of the information environment of university are identified. Building a system hierarchically ensures the effective management of subsystems of organization of educational process and interaction between participants of the educational process and allows the system to change quickly if it is necessary.

  15. Processes and modeling of hydrolysis of particulate organic matter in aerobic wastewater tratment - A review

    DEFF Research Database (Denmark)

    Morgenroth, Eberhard Friedrich; Kommedal, Roald; Harremoës, Poul

    2002-01-01

    Carbon cycling and the availability of organic carbon for nutrient removal processes are in most wastewater treatment systems restricted by the rate of hydrolysis of slowly biodegradable (particulate) organic matter. To date, the mechanisms of hydrolysis are not well understood for complex...

  16. Processes controlling the production of aromatic water-soluble organic matter during litter decomposition

    NARCIS (Netherlands)

    Klotzbücher, T.; Kaiser, K.; Filley, T.R.; Kalbitz, K.

    2013-01-01

    Dissolved organic matter (DOM) plays a fundamental role for many soil processes. For instance, production, transport, and retention of DOM control properties and long-term storage of organic matter in mineral soils. Production of water-soluble compounds during the decomposition of plant litter is a

  17. Processing and performance of organic insulators as a gate layer in ...

    Indian Academy of Sciences (India)

    Fabrication of organic thin film transistor (OTFT) on flexible substrates is a challenge, because of its low softening temperature, high roughness and flexible nature. Although several organic dielectrics have been used as gate insulator, it is difficult to choose one in absence of a comparative study covering processing of ...

  18. A mechanistic understanding of processing additive-induced efficiency enhancement in bulk heterojunction organic solar cells

    KAUST Repository

    Schmidt, Kristin; Tassone, Christopher J.; Niskala, Jeremy R.; Yiu, Alan T.; Lee, Olivia P.; Weiss, Thomas M.; Wang, Cheng; Frechet, Jean; Beaujuge, Pierre; Toney, Michael F.

    2013-01-01

    The addition of processing additives is a widely used approach to increase power conversion efficiencies for many organic solar cells. We present how additives change the polymer conformation in the casting solution leading to a more intermixed

  19. The socialization of students in the process of art activity in a mixed-age organization

    Directory of Open Access Journals (Sweden)

    Khomenko N.Yu.

    2017-01-01

    Full Text Available the article analyzes the experience of pedagogical research of students’ socialization in the process of their art activity in a mixed-age organization. It also provides the characteristic of some results, obtained in the research.

  20. Characterizing natural organic matter in drinking water treatment processes and trains

    NARCIS (Netherlands)

    Baghoth, S.A.

    2012-01-01

    Natural organic matter (NOM) generally influences water treatment processes such as coagulation, oxidation, adsorption, and membrane filtration. NOM contributes colour, taste and odour in drinking water, fouls membranes, serves as a precursor for disinfection by-products, increases the exhaustion

  1. Fully solution-processed organic solar cells on metal foil substrates

    KAUST Repository

    Gaynor, Whitney; Lee, Jung-Yong; Peumans, Peter

    2009-01-01

    We demonstrate fully solution-processed organic photovoltaic cells on metal foil substrates with power conversion efficiencies similar to those obtained in devices on transparent substrates. The cells are based on the regioregular poly- (3

  2. Solution-Processed Molecular Organic Solar cell: Relationship between Morphology and Device Performance

    KAUST Repository

    Babics, Maxime

    2018-01-01

    ) the rationalization of material design and (ii) systematic optimization of film processing condition. OPV can have a key role in markets such as building-integrated photovoltaics (BIPV). The main advantages of organic solar cells are semitransparency, low weight, good

  3. Organizational factors affecting the adoption of diabetes care management processes in physician organizations.

    Science.gov (United States)

    Li, Rui; Simon, Jodi; Bodenheimer, Thomas; Gillies, Robin R; Casalino, Lawrence; Schmittdiel, Julie; Shortell, Stephen M

    2004-10-01

    To describe the extent of adoption of diabetes care management processes in physician organizations in the U.S. and to investigate the organizational factors that affect the adoption of diabetes care management processes. Data are derived from the National Survey of Physician Organizations and the Management of Chronic Illness, conducted in 2000-2001. A total of 1,104 of the 1,590 physician organizations identified responded to the survey. The extent of adoption of four diabetes care management processes is measured by an index consisting of the organization's use of diabetic patient registries, clinical practice guidelines, case management, and physician feedback. The ordinary least-squares model is used to determine the association of organizational characteristics with the adoption of diabetes care management processes in physician organizations. A logistic regression model is used to determine the association of organizational characteristics with the adoption of individual diabetes care management processes. Of the 987 physician organizations studied that treat patients with diabetes, 48% either do not use any or use only one of the four diabetes care management processes. A total of 20% use two care management processes, and 32% use three or four processes. External incentives to improve quality, computerized clinical information systems, and ownership by hospitals or health maintenance organizations are strongly associated with the diabetes care management index and the adoption of individual diabetes care management processes. Policies to encourage external incentives to improve quality and to facilitate the adoption of computerized clinical information technology may promote greater use of diabetes care management processes. Copyright 2004 American Diabetes Association

  4. Laser Control of Self-Organization Process in Microscopic Region and Fabrication of Fine Microporous Structure

    OpenAIRE

    Matsumura, Yukimasa; Inami, Wataru; Kawata, Yoshimasa

    2012-01-01

    We present a controlling technique of microporous structure by laser irradiation during self-organization process. Self-organization process is fabrication method of microstructure. Polymer solution was dropped on the substrate at high humid condition. Water in air appears dropping air temperature below the dew point. The honeycomb structure with regularly aligned pores on the film was fabricated by attaching water droplets onto the solution surface. We demonstrate that it was possible to pre...

  5. Experience of nurses in the process of donation of organs and tissues for transplant

    OpenAIRE

    Moraes,Edvaldo Leal de; Santos,Marcelo José dos; Merighi,Miriam Aparecida Barbosa; Massarollo,Maria Cristina Komatsu Braga

    2014-01-01

    OBJECTIVE: to investigate the meaning of the action of nurses in the donation process to maintain the viability of organs and tissues for transplantation.METHOD: this qualitative study with a social phenomenological approach was conducted through individual interviews with ten nurses of three Organ and Tissue Procurement Services of the city of São Paulo.RESULTS: the experience of the nurses in the donation process was represented by the categories: obstacles experienced in the donation proce...

  6. High rates of organic carbon processing in the hyporheic zone of intermittent streams.

    Science.gov (United States)

    Burrows, Ryan M; Rutlidge, Helen; Bond, Nick R; Eberhard, Stefan M; Auhl, Alexandra; Andersen, Martin S; Valdez, Dominic G; Kennard, Mark J

    2017-10-16

    Organic carbon cycling is a fundamental process that underpins energy transfer through the biosphere. However, little is known about the rates of particulate organic carbon processing in the hyporheic zone of intermittent streams, which is often the only wetted environment remaining when surface flows cease. We used leaf litter and cotton decomposition assays, as well as rates of microbial respiration, to quantify rates of organic carbon processing in surface and hyporheic environments of intermittent and perennial streams under a range of substrate saturation conditions. Leaf litter processing was 48% greater, and cotton processing 124% greater, in the hyporheic zone compared to surface environments when calculated over multiple substrate saturation conditions. Processing was also greater in more saturated surface environments (i.e. pools). Further, rates of microbial respiration on incubated substrates in the hyporheic zone were similar to, or greater than, rates in surface environments. Our results highlight that intermittent streams are important locations for particulate organic carbon processing and that the hyporheic zone sustains this fundamental process even without surface flow. Not accounting for carbon processing in the hyporheic zone of intermittent streams may lead to an underestimation of its local ecological significance and collective contribution to landscape carbon processes.

  7. Process and device for liquid organic waste processing by sulfuric mineralization

    International Nuclear Information System (INIS)

    Aspart, A.; Gillet, B.; Lours, S.; Guillaume, B.

    1990-01-01

    In a chemical reactor containing sulfuric acid are introduced the liquid waste and nitric acid at a controlled flow rate for carbonization of the waste and oxidation of carbon on sulfur dioxide, formed during carbonization, regenerating simultaneously sulfuric acid. Optical density of the liquid is monitored to stop liquid waste feeding above a set-point. The liquid waste can be an organic solvent such as TBP [fr

  8. Image processing in cine-scintigraphy. Organization of the CINE 200 system

    International Nuclear Information System (INIS)

    Tournier, E.; Axelrad, C.; Monge, J.; Beccia, A.; Bouvier, A.

    1975-01-01

    The CINE 200 system, although using a small computer to reduce costs, is shown to be a highly efficient instrument for the processing of scintigraphic images. This was achieved by creating an acquisition and display system branched directly onto the memory, reducing the processing times by the writing of fast micro-programmes, and cutting down the place occupied by the programmes in the live memory by a good organization of these programmes. This internal organization of the system, the insertion and role of the programmes, the data organization and the working procedure are described briefly [fr

  9. Reformation of organization and realization of budgetary process: basic directions, problems and ways of their solution

    Directory of Open Access Journals (Sweden)

    E.B. Ponomarenko

    2015-12-01

    Full Text Available The article is dedicated to the research of the basic problems of organization and realization of budgetary process in the country on the modern stage. A budgetary process is one of the main levers which is able really to provide management of an economy under conditions of a market economy. Organizational and administrative structures of the budgetary process are ineffective in Ukraine. In spite of more than twenty-year old history, the budgetary process of Ukraine has the row of unsolved problems. For this reason there is the necessity in deep theoretical rethinking and methodological work at approaches to the budgetary process. We consider it is wise to find out the basic problems which arise during organization and realization of the budgetary process in Ukraine. The study of the matter results in the complex of recommendations which are able to provide effective realization of the budgetary process in Ukraine and solve a number of problem questions.

  10. Sol-gel Process in Preparation of Organic-inorganic Hybrid Materials

    Directory of Open Access Journals (Sweden)

    Macan, J

    2008-07-01

    Full Text Available Organic-inorganic hybrid materials are a sort of nanostructured material in which the organic and inorganic phases are mixed at molecular level. The inorganic phase in hybrid materials is formed by the sol-gel process, which consists of reactions of hydrolysis and condensation of metal (usually silicon alkoxides. Flexibility of sol-gel process enables creation of hybrid materials with varying organic and inorganic phases in different ratios, and consequently fine-tuning of their properties. In order to obtain true hybrid materials, contact between the phases should be at molecular level, so phase separation between thermodynamically incompatible organic and inorganic phases has to be prevented. Phase interaction can be improved by formation of hydrogen or covalent bonds between them during preparation of hybrid materials. Covalent bond can be introduced by organically modified silicon alkoxides containing a reactive organic group (substituent capable of reacting with the organic phase. In order to obtain hybrid materials with desired structures, a detailed knowledge of hydrolysis and condensation mechanism is necessary. The choice of catalyst, whether acid or base, has the most significant influence on the structure of the inorganic phase. Other important parameters are alkoxide concentration, water: alkoxide ratio, type of alkoxide groups, solvent used, temperature, purity of chemicals used, etc. Hydrolysis and condensation of organically modified silicon alkoxides are additionally influenced by nature and size of the organic supstituent.

  11. Self-organization process of a magnetohydrodynamic plasma in the presence of thermal conduction

    International Nuclear Information System (INIS)

    Zhu, Shao-ping; Horiuchi, Ritoku; Sato, Tetsuya; Watanabe, K.; Hayashi, T.; Todo, Y.; Watanabe, T.H.; Kageyama, A.; Takamaru, H.

    1995-12-01

    A self-organization process of a magnetohydrodynamic(MHD) plasma with a finite thermal conductivity is investigated by means of a three-dimensional MHD simulation. With no thermal conduction an MHD system self-organizes to a non-Taylor's state in which the electric current perpendicular to the magnetic field remains comparable to the parallel electric current. In the presence of thermal conductivity the perpendicular component of electric current and the nonuniformity of thermal pressure generated by driven reconnection tend to be smoothened. Thus, the self-organized state approaches to a force-free minimum energy state under the influence of thermal conduction. Detailed energy conversion processes are also studied to find that the rapid decay of magnetic energy during the self-organization process is caused not only through the ohmic heating, but also through the work done by the j x B force. (author)

  12. [Efficiency indicators to assess the organ donation and transplantation process: systematic review of the literature].

    Science.gov (United States)

    Siqueira, Marina Martins; Araujo, Claudia Affonso; de Aguiar Roza, Bartira; Schirmer, Janine

    2016-08-01

    To search the literature and identify indicators used to monitor and control the organ donation and transplantation process and to group these indicators into categories. In November 2014, a systematic review of the literature was carried out in the following databases: Biblioteca Virtual em Saúde (BVS), EBSCO, Emerald, Proquest, Science Direct, and Web of Science. The following search terms (and the corresponding terms in Brazilian Portuguese) were employed: "efficiency," "indicators," "organ donation," "tissue and organ procurement," and "organ transplantation." Of the 344 articles retrieved, 23 original articles published between 1992 and 2013 were selected and reviewed for analysis of efficiency indicators. The review revealed 117 efficiency indicators, which were grouped according to similarity of content and divided into three categories: 1) 71 indicators related to organ donation, covering mortality statistics, communication of brain death, clinical status of donors and exclusion of donors for medical reasons, attitude of families, confirmation of donations, and extraction of organs and tissues; 2) 22 indicators related to organ transplantation, covering the surgical procedure per se and post-transplantation follow-up; and 3) 24 indicators related to the demand for organs and the resources of hospitals involved in the process. Even if organ transplantation is a recent phenomenon, the high number of efficiency indicators described in the literature suggests that scholars interested in this field have been searching for ways to measure performance. However, there is little standardization of the indicators used. Also, most indicators focus on the donation step, suggesting gaps in the measurement of efficiency at others points in the process. Additional indicators are needed to monitor important stages, such as organ distribution (for example, organ loss indicators) and post-transplantation aspects (for example, survival and quality of life).

  13. 42 CFR 410.142 - CMS process for approving national accreditation organizations.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 2 2010-10-01 2010-10-01 false CMS process for approving national accreditation... Diabetes Self-Management Training and Diabetes Outcome Measurements § 410.142 CMS process for approving national accreditation organizations. (a) General rule. CMS may approve and recognize a nonprofit or not...

  14. Impact of processing on in vitro digestion of milk from grazing organic and confined conventional herds

    Science.gov (United States)

    Debate on differences between milk from grazing and non-grazing cows has not addressed the effects that standard processing may have on milk digestibility. In this study, raw milk from grazing organic (ORG) and non-grazing conventional (CONV) herds was adjusted to 0 and 3.25% fat and processed as fo...

  15. Top contact organic field effect transistors fabricated using a photolithographic process

    International Nuclear Information System (INIS)

    Wang Hong; Peng Ying-Quan; Ji Zhuo-Yu; Shang Li-Wei; Liu Xing-Hua; Liu Ming

    2011-01-01

    This paper proposes an effective method of fabricating top contact organic field effect transistors by using a photolithographic process. The semiconductor layer is protected by a passivation layer. Through photolithographic and etching processes, parts of the passivation layer are etched off to form source/drain electrode patterns. Combined with conventional evaporation and lift-off techniques, organic field effect transistors with a top contact are fabricated successfully, whose properties are comparable to those prepared with the shadow mask method and one order of magnitude higher than the bottom contact devices fabricated by using a photolithographic process. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  16. Regional Differences in Communication Process and Outcomes of Requests for Solid Organ Donation.

    Science.gov (United States)

    Traino, H M; Molisani, A J; Siminoff, L A

    2017-06-01

    Although federal mandate prohibits the allocation of solid organs for transplantation based on "accidents of geography," geographic variation of transplantable organs is well documented. This study explores regional differences in communication in requests for organ donation. Administrative data from nine partnering organ procurement organizations and interview data from 1339 family decision makers (FDMs) were compared across eight geographically distinct US donor service areas (DSAs). Authorization for organ donation ranged from 60.4% to 98.1% across DSAs. FDMs from the three regions with the lowest authorization rates reported the lowest levels of satisfaction with the time spent discussing donation and with the request process, discussion of the least donation-related topics, the highest levels of pressure to donate, and the least comfort with the donation decision. Organ procurement organization region predicted authorization (odds ratios ranged from 8.14 to 0.24), as did time spent discussing donation (OR = 2.11), the number of donation-related topics discussed (OR = 1.14), and requesters' communication skill (OR = 1.14). Standardized training for organ donation request staff is needed to ensure the highest quality communication during requests, optimize rates of family authorization to donation in all regions, and increase the supply of organs available for transplantation. © 2016 The American Society of Transplantation and the American Society of Transplant Surgeons.

  17. A review of observations of organic matter in fogs and clouds: Origin, processing and fate

    Science.gov (United States)

    Herckes, Pierre; Valsaraj, Kalliat T.; Collett, Jeffrey L.

    2013-10-01

    While fog and cloud composition has been studied for decades, most of the research was limited to inorganic species and fog acidity. Recently the focus has shifted towards organic matter in the atmospheric aqueous phase of fogs and clouds: its origin, reactivity and fate. An impressive number of fog and cloud chemistry observational studies have been performed over the last decade throughout the world. In the present work we will review the state of knowledge of atmospheric organic matter processing by fogs, with a focus on field observations. We start by reviewing observational studies in general and then discuss our knowledge on the occurrence of organic matter in fogs, its solubility, characterization and molecular speciation. Organic carbon concentrations can vary widely from approximately 1 mg C/L in remote marine environments to more than 100 mg C/L in polluted radiation fogs, accounting for a substantial part of fogwater solutes. The carbonaceous material can enter the droplets from the gas and particle phase and the scavenging behavior of fogs will be detailed. Observational studies showed evidence of aqueous phase transformation of organic material, in particular secondary organic aerosol (SOA) generation, in fog. Recent observations of biological material in fog suggest also an impact of biological processing within the droplets on fog organic matter. The review will end with a discussion of the impact of fog on the deposition fluxes of organic material and hence its atmospheric lifetime.

  18. Solution processed organic light-emitting diodes using the plasma cross-linking technology

    Energy Technology Data Exchange (ETDEWEB)

    He, Kongduo [Department of Light Sources and Illuminating Engineering, Fudan University, Shanghai 200433 (China); Liu, Yang [Department of Light Sources and Illuminating Engineering, Fudan University, Shanghai 200433 (China); Engineering Research Center of Advanced Lighting Technology, Ministry of Education, Shanghai 200433 (China); Gong, Junyi; Zeng, Pan; Kong, Xun; Yang, Xilu; Yang, Cheng; Yu, Yan [Department of Light Sources and Illuminating Engineering, Fudan University, Shanghai 200433 (China); Liang, Rongqing [Department of Light Sources and Illuminating Engineering, Fudan University, Shanghai 200433 (China); Engineering Research Center of Advanced Lighting Technology, Ministry of Education, Shanghai 200433 (China); Ou, Qiongrong, E-mail: qrou@fudan.edu.cn [Department of Light Sources and Illuminating Engineering, Fudan University, Shanghai 200433 (China); Engineering Research Center of Advanced Lighting Technology, Ministry of Education, Shanghai 200433 (China)

    2016-09-30

    Highlights: • Mixed acetylene and Ar plasma treatment makes the organic film surface cross-linked. • The plasma treatment for 30 s does not affect the performance of OLEDs. • Cross-linking surface can resist rinsing and corrosion of organic solvent. • The surface morphology is nearly unchanged after plasma treatment. • The plasma cross-linking method can realize solution processed multilayer OLEDs. - Abstract: Solution processed multilayer organic light-emitting diodes (OLEDs) present challenges, especially regarding dissolution of the first layer during deposition of a second layer. In this work, we first demonstrated a plasma cross-linking technology to produce a solution processed OLED. The surfaces of organic films can be cross-linked after mixed acetylene and Ar plasma treatment for several tens of seconds and resist corrosion of organic solvent. The film thickness and surface morphology of emissive layers (EMLs) with plasma treatment and subsequently spin-rinsed with chlorobenzene are nearly unchanged. The solution processed triple-layer OLED is successfully fabricated and the current efficiency increases 50% than that of the double-layer OLED. Fluorescent characteristics of EMLs are also observed to investigate factors influencing the efficiency of the triple-layer OLED. Plasma cross-linking technology may open up a new pathway towards fabrication of all-solution processed multilayer OLEDs and other soft electronic devices.

  19. Decision maker perceptions of resource allocation processes in Canadian health care organizations: a national survey.

    Science.gov (United States)

    Smith, Neale; Mitton, Craig; Bryan, Stirling; Davidson, Alan; Urquhart, Bonnie; Gibson, Jennifer L; Peacock, Stuart; Donaldson, Cam

    2013-07-02

    Resource allocation is a key challenge for healthcare decision makers. While several case studies of organizational practice exist, there have been few large-scale cross-organization comparisons. Between January and April 2011, we conducted an on-line survey of senior decision makers within regional health authorities (and closely equivalent organizations) across all Canadian provinces and territories. We received returns from 92 individual managers, from 60 out of 89 organizations in total. The survey inquired about structures, process features, and behaviours related to organization-wide resource allocation decisions. We focus here on three main aspects: type of process, perceived fairness, and overall rating. About one-half of respondents indicated that their organization used a formal process for resource allocation, while the others reported that political or historical factors were predominant. Seventy percent (70%) of respondents self-reported that their resource allocation process was fair and just over one-half assessed their process as 'good' or 'very good'. This paper explores these findings in greater detail and assesses them in context of the larger literature. Data from this large-scale cross-jurisdictional survey helps to illustrate common challenges and areas of positive performance among Canada's health system leadership teams.

  20. Study into an organization for collecting, processing and removing of radioactive waste

    International Nuclear Information System (INIS)

    1983-09-01

    This report presents the results of a study into a new organization for the collection, processing and removal of radioactive waste. At present these activities are carried out by the Dutch Energy Research Foundation (ECN). The new organization has to offer guarantees for a qualititatively responsible retrieval and processing of radioactive waste. It also has to be certain that the waste offered will not be send back, or even refused, if stagnation occurs in the removal. Finally the tariffs have to be not so prohibitive that they hinder a responsible handling with radioactive waste by the producers. An organization is advised which is self-employed with regard to management, directorate and materials. It is recommended to submit this organization in a limited liability company. This form of government may be supplemented optionally with a slight form of a cooperative association. (author). 10 refs.; 3 figs.; 11 tabs

  1. Mass transfer processes and field-scale transport of organic solutes

    International Nuclear Information System (INIS)

    Brusseau, M.L.

    1990-01-01

    The influence of mass transfer processes, such as sorption/desorption and mass transfer between immiscible liquids and water, on the transport of organic solutes is discussed. Rate-limited sorption of organic solutes caused by a diffusion-constrained mechanism is shown to be significant under laboratory conditions. The significance of the impact of nonequilibrium sorption on field-scale transport is scale dependent. The impact of organic liquids on mass transfer and transport of organic solutes depends upon the nature of the solute and the nature and form of the organic liquid. For example, while retardation of nonionic solutes is decreased in mixed-solvent systems, (i.e. systems comprised of water and a miscible organic liquid or an immiscible liquid present in concentrations below phase separation), the retardation of organic acids may, in some cases, increase with addition of a cosolvent. While the presence of an immiscible liquid existing as a mobile phase will reduce retention of organic solutes, the presence of residual saturation of an immiscible liquid can significantly increase retention. A model is presented that incorporates the effects of retention resulting from residual saturation, as well as nonequilibrium sorption, on the transport of organic solutes. (Author) (70 refs., 3 figs.)

  2. Electronic processes in organic electronics bridging nanostructure, electronic states and device properties

    CERN Document Server

    Kudo, Kazuhiro; Nakayama, Takashi; Ueno, Nobuo

    2015-01-01

    The book covers a variety of studies of organic semiconductors, from fundamental electronic states to device applications, including theoretical studies. Furthermore, innovative experimental techniques, e.g., ultrahigh sensitivity photoelectron spectroscopy, photoelectron yield spectroscopy, spin-resolved scanning tunneling microscopy (STM), and a material processing method with optical-vortex and polarization-vortex lasers, are introduced. As this book is intended to serve as a textbook for a graduate level course or as reference material for researchers in organic electronics and nanoscience from electronic states, fundamental science that is necessary to understand the research is described. It does not duplicate the books already written on organic electronics, but focuses mainly on electronic properties that arise from the nature of organic semiconductors (molecular solids). The new experimental methods introduced in this book are applicable to various materials (e.g., metals, inorganic and organic mater...

  3. Anammox for ammonia removal from pig manure effluents: Effect of organic matter content on process performance

    DEFF Research Database (Denmark)

    Salces, Beatriz Molinuevo; García, M. C.; Karakashev, Dimitar Borisov

    2009-01-01

    oxidation) diluted with synthetic wastewater. High ammonium removal was achieved, up to 92.1 +/- 4.9% for diluted UASB-post-digested effluent (95 mg COD L-1) and up to 98.5 +/- 0.8% for diluted partially oxidized effluent (121 mg COD L-1). Mass balance clearly showed that an increase in organic loading......The anammox process, under different organic loading rates (COD), was evaluated using a semi-continous UASB reactor at 37 degrees C. Three different substrates were used: initially, synthetic wastewater, and later, two different pig manure effluents (after UASB-post-digestion and after partial...... improved ammonium removal at high organic matter concentration. Up to threshold organic load concentration of 142 mg COD L-1 of UASB-post-digested effluent and 242 mg COD L-1 of partially oxidized effluent, no effect of organic loading on ammonia removal was registered (ammonium removal was above 80...

  4. Solution-processed copper-nickel nanowire anodes for organic solar cells

    Science.gov (United States)

    Stewart, Ian E.; Rathmell, Aaron R.; Yan, Liang; Ye, Shengrong; Flowers, Patrick F.; You, Wei; Wiley, Benjamin J.

    2014-05-01

    This work describes a process to make anodes for organic solar cells from copper-nickel nanowires with solution-phase processing. Copper nanowire films were coated from solution onto glass and made conductive by dipping them in acetic acid. Acetic acid removes the passivating oxide from the surface of copper nanowires, thereby reducing the contact resistance between nanowires to nearly the same extent as hydrogen annealing. Films of copper nanowires were made as oxidation resistant as silver nanowires under dry and humid conditions by dipping them in an electroless nickel plating solution. Organic solar cells utilizing these completely solution-processed copper-nickel nanowire films exhibited efficiencies of 4.9%.This work describes a process to make anodes for organic solar cells from copper-nickel nanowires with solution-phase processing. Copper nanowire films were coated from solution onto glass and made conductive by dipping them in acetic acid. Acetic acid removes the passivating oxide from the surface of copper nanowires, thereby reducing the contact resistance between nanowires to nearly the same extent as hydrogen annealing. Films of copper nanowires were made as oxidation resistant as silver nanowires under dry and humid conditions by dipping them in an electroless nickel plating solution. Organic solar cells utilizing these completely solution-processed copper-nickel nanowire films exhibited efficiencies of 4.9%. Electronic supplementary information (ESI) available. See DOI: 10.1039/c4nr01024h

  5. EXPECTED IMPACT OF HANFORD PROCESSING ORGANICS OF PLUTONIUM DURING TANK WASTE SLUDGE RETRIEVAL

    International Nuclear Information System (INIS)

    TROYER, G.L.; WINTERS, W.I.

    2004-01-01

    This document evaluates the potential for extracting plutonium from Hanford waste tanks into residual organic solvents and how this process may have an impact on criticality specifications during the retrieval of wastes. The two controlling factors for concentrating plutonium are the solubility of the plutonium in the wastes and the extraction efficiency of the potential organic extractants that may be found in these wastes. Residual Hanford tank sludges contain plutonium in solid forms that are expected to be primarily insoluble Pu(IV) hydroxides. Evaluation of thermodynamic Pourbaix diagrams, documentation on solubility studies of various components in waste tank matrices, and actual analysis of plutonium in tank supernates all indicate that the solubility of Pu in the alkaline waste is on the order of 10 -6 M. Based on an upper limit plutonium solubility of 10 -5 M in high pH and a conservative distribution coefficient for organic extractants of a 0 for plutonium in 30% TBP at 0.07 M HNO 3 ), the estimated concentration for plutonium in the organic phase would be -7 M. This is well below the process control criteria. A significant increase in plutonium solubility or the E a o would have to occur to raise this concentration to the 0.01 M concern level for organics. Measured tank chemical component values, expected operating conditions, and the characteristics of the expected chemistry and extraction mechanisms indicate that concentration of plutonium from Hanford tank residual sludges to associated process organic extractants is significantly below levels of concern

  6. A Relational Approach to the Acquisition Decision-Making Process in the Military Organization

    Directory of Open Access Journals (Sweden)

    Gheorghe Minculete

    2016-06-01

    Full Text Available The market relations of military organizations focus on the acquisition of material goods and/or services. Nonetheless, the importance of the decisions related to the supply process is sometimes minimized. This attitude is so harmful for the effi cacy and effi ciency of the activities conducted by the military structure that at times it can have a negative impact on the management staff too. Problems may occur because the acquisition process must unfold performance-oriented; its main objective is the purchasing of material goods and/or services meant to ensure the smooth operation of the activities of the military organization. In case this cannot be achieved, it is highly probable that the mission of the organization itself is compromised. The present article explores the constitutive elements of the acquisition decision-making situation, certainty, uncertainty and risk connected to the purchasing mechanism, as well as the stages of the acquisition decision-making process

  7. Vitrification process for the volume reduction and stabilization of organic resins

    International Nuclear Information System (INIS)

    Buelt, J.L.

    1982-10-01

    Pacific Northwest Laboratory has completed a series of experimental tests sponsored by the US Department of Energy (DOE) to determine the feasibility of incinerating and vitrifying organic ion-exchange resins in a single-step process. The resins used in this study were identical to those used for decontaminating auxiliary building water at the Three Mile Island (TMI) Unit 2 reactor. The primarily organic resins were loaded with nonradioactive isotopes of cesium and strontium for processing in a pilot-scale, joule-heated glass melter modified to support resin combustion. The feasibility tests demonstrated an average process rate of 3.0 kg/h. Based on this rate, if 50 organic resin liners were vitrified in a six-month campaign, a melter 2.5 times the size of the pilot scale unit would be adequate. A maximum achievable volume reduction of 91% was demonstrated in these tests

  8. Solidification method for organic solution and processing method of aqueous solution

    International Nuclear Information System (INIS)

    Kamoshida, Mamoru; Fukazawa, Tetsuo; Yazawa, Noriko; Hasegawa, Toshihiko

    1998-01-01

    The relative dielectric constant of an organic solution containing polar ingredients is controlled to 13 or less to enable its solidification. The polarity of the organic solution can be evaluated quantitatively by using the relative dielectric constant. If the relative dielectric constant is high, it can be controlled by dilution using a non-polar organic solvent of low relative dielectric constant. With such procedures, solidification can be conducted by using an economical 12-hydroxy stearic acid, process of liquid wastes can be facilitated and the safety can be ensured. (T.M.)

  9. Solution-Processed Wide-Bandgap Organic Semiconductor Nanostructures Arrays for Nonvolatile Organic Field-Effect Transistor Memory.

    Science.gov (United States)

    Li, Wen; Guo, Fengning; Ling, Haifeng; Liu, Hui; Yi, Mingdong; Zhang, Peng; Wang, Wenjun; Xie, Linghai; Huang, Wei

    2018-01-01

    In this paper, the development of organic field-effect transistor (OFET) memory device based on isolated and ordered nanostructures (NSs) arrays of wide-bandgap (WBG) small-molecule organic semiconductor material [2-(9-(4-(octyloxy)phenyl)-9H-fluoren-2-yl)thiophene]3 (WG 3 ) is reported. The WG 3 NSs are prepared from phase separation by spin-coating blend solutions of WG 3 /trimethylolpropane (TMP), and then introduced as charge storage elements for nonvolatile OFET memory devices. Compared to the OFET memory device with smooth WG 3 film, the device based on WG 3 NSs arrays exhibits significant improvements in memory performance including larger memory window (≈45 V), faster switching speed (≈1 s), stable retention capability (>10 4 s), and reliable switching properties. A quantitative study of the WG 3 NSs morphology reveals that enhanced memory performance is attributed to the improved charge trapping/charge-exciton annihilation efficiency induced by increased contact area between the WG 3 NSs and pentacene layer. This versatile solution-processing approach to preparing WG 3 NSs arrays as charge trapping sites allows for fabrication of high-performance nonvolatile OFET memory devices, which could be applicable to a wide range of WBG organic semiconductor materials. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Importance of nitrogen in the decomposition of various organic substances in the Bihugas process

    Energy Technology Data Exchange (ETDEWEB)

    Scheffer, F; Bruene, H

    1955-01-01

    About 30 percent of the organic matter is decomposed during the fermentation process, 20-25 percent of the organic N being mineralized to NH/sub 3/. Trials with straw, sisal, peat, etc., showed that additional mineral N promotes the fermentation process of substances which decompose rapidly or are poor in easily available N compounds, except potato starch which decomposes without any notable fixation of N. Results did not confirm claims on the beneficial effects of hormone preparations and on killing of pathogenic typhus-enteritis bacteria during fermentation.

  11. Migration through soil of organic solutes in an oil-shale process water

    Science.gov (United States)

    Leenheer, J.A.; Stuber, H.A.

    1981-01-01

    The migration through soil of organic solutes in an oil-shale process water (retort water) was studied by using soil columns and analyzing leachates for various organic constituents. Retort water extracted significant quantities of organic anions leached from ammonium-saturated-soil organic matter, and a distilled-water rinse, which followed retort-water leaching, released additional organic acids from the soil. After being corrected for organic constitutents extracted from soil by retort water, dissolved-organic-carbon fractionation analyses of effluent fractions showed that the order of increasing affinity of six organic compound classes for the soil was as follows: hydrophilic neutrals nearly equal to hydrophilic acids, followed by the sequence of hydrophobic acids, hydrophilic bases, hydrophobic bases, and hydrophobic neutrals. Liquid-chromatographic analysis of the aromatic amines in the hydrophobic- and hydrophilic-base fractions showed that the relative order of the rates of migration through the soil column was the same as the order of migration on a reversed-phase, octadecylsilica liquid-chromatographic column.

  12. Investigation of processes of interaction relativistic electrons with the solutions of organic dyes

    International Nuclear Information System (INIS)

    Buki, A.Yu.; Gokov, S.P.; Kazarinov, Yu.G.; Kalenik, S.A.; Kasilov, V.I.; Kochetov, S.S.; Makhnenko, P.L.; Mel'nitskiy, I.V.; Tverdohvalov, A.V.; Tsyatsko, V.V.; Shopen, O.A.

    2014-01-01

    Investigation of the processes of interaction of ionizing radiation with complex organic objects can solve a number of fundamental and applied problems in radiation physics, chemistry and biology. In this work we investigated the dose dependence (dose range 1...5MRad) optical density relative concentrations of water, alcohol and glycerine solution following organic dyes: methylene blue - C 16 H 18 N 3 SCl and methyl orange - C 14 H 14 N 3 O 3 SNa, irradiated with an electron beam with an energy of 16MeV. In the analysis of absorption spectra, it was found that water solutions of dyes have less resistance to radiation as compared with the alcohol and glycerol. Also, all solutions of methyl orange less radiation resistant than the methylene blue solution. Analysis of the spectra showed that these relationships are close to linear in the range of doses. To understand the physical and chemical processes occurring in the interaction of relativistic electrons with the studied organic objects were performed the computer simulations of the energy spectra of ions formed due to breaking the chemical bonds of molecules of dye solutions using the program SRIM-2010. The analysis showed that radiation - stimulated chemical processes play a major role in the destruction of the source of organic dye molecules. The remaining processes (interaction of electrons and nuclei, the cascade processes) accounts for about 10% of all molecular breaks.

  13. Design of Biochemical Oxidation Process Engineering Unit for Treatment of Organic Radioactive Liquid Waste

    International Nuclear Information System (INIS)

    Zainus Salimin; Endang Nuraeni; Mirawaty; Tarigan, Cerdas

    2010-01-01

    Organic radioactive liquid waste from nuclear industry consist of detergent waste from nuclear laundry, 30% TBP-kerosene solvent waste from purification or recovery of uranium from process failure of nuclear fuel fabrication, and solvent waste containing D 2 EHPA, TOPO, and kerosene from purification of phosphoric acid. The waste is dangerous and toxic matter having low pH, high COD and BOD, and also low radioactivity. Biochemical oxidation process is the effective method for detoxification of organic waste and decontamination of radionuclide by bio sorption. The result process are sludges and non radioactive supernatant. The existing treatment facilities radioactive waste in Serpong can not use for treatment of that’s organics waste. Dio chemical oxidation process engineering unit for continuous treatment of organic radioactive liquid waste on the capacity of 1.6 L/h has been designed and constructed the equipment of process unit consist of storage tank of 100 L capacity for nutrition solution, 2 storage tanks of 100 L capacity per each for liquid waste, reactor oxidation of 120 L, settling tank of 50 L capacity storage tank of 55 L capacity for sludge, storage tank of 50 capacity for supernatant. Solution on the reactor R-01 are added by bacteria, nutrition and aeration using two difference aerators until biochemical oxidation occurs. The sludge from reactor of R-01 are recirculated to the settling tank of R-02 and on the its reverse operation biological sludge will be settled, and supernatant will be overflow. (author)

  14. Process engineering versus product engineering - A case study on volatile organic compounds removal

    DEFF Research Database (Denmark)

    Coutinho, João A.P.; Vilela, T.; Pereira, P.

    2005-01-01

    Three solutions for removing the dangerous volatile organic compound (VOC) xylene from an industrial coating process are presented and compared. Two of them are based on classical process engineering principles, i.e., development of separation-cleaning methods such as incineration and adsorption...... to the problem-need specified in the beginning of the project, but producing a novel formulation (chemical product design) represents a method that results to a completely xylene-free process which is environmentally and economically more interesting than those generated via the more traditional process...

  15. Quality assessment of baby food made of different pre-processed organic raw materials under industrial processing conditions.

    Science.gov (United States)

    Seidel, Kathrin; Kahl, Johannes; Paoletti, Flavio; Birlouez, Ines; Busscher, Nicolaas; Kretzschmar, Ursula; Särkkä-Tirkkonen, Marjo; Seljåsen, Randi; Sinesio, Fiorella; Torp, Torfinn; Baiamonte, Irene

    2015-02-01

    The market for processed food is rapidly growing. The industry needs methods for "processing with care" leading to high quality products in order to meet consumers' expectations. Processing influences the quality of the finished product through various factors. In carrot baby food, these are the raw material, the pre-processing and storage treatments as well as the processing conditions. In this study, a quality assessment was performed on baby food made from different pre-processed raw materials. The experiments were carried out under industrial conditions using fresh, frozen and stored organic carrots as raw material. Statistically significant differences were found for sensory attributes among the three autoclaved puree samples (e.g. overall odour F = 90.72, p processed from frozen carrots show increased moisture content and decrease of several chemical constituents. Biocrystallization identified changes between replications of the cooking. Pre-treatment of raw material has a significant influence on the final quality of the baby food.

  16. Enhancing Competitiveness Business Strategy of Organic Vegetables Using Analytical Hierarchy Process (AHP

    Directory of Open Access Journals (Sweden)

    Pristiana Widyastuti

    2017-09-01

    Full Text Available Public awareness about healthy lifestyles leads people to want to understand more about the food they consume. Choosing organic vegetables is one alternative choices when seeking to have a healthy body and healthy lifestyle. Unfortunately, not a lot of organic vegetable farmers in Indonesia succeed in seizing the organic vegetable market rather than the non-organic and the competition with imported organic vegetables into Indonesia prevents farmers from thriving. This study aims to: 1 Analyze the factors affecting the competitiveness of the organic vegetables market; 2 Analyze the appropriate strategy for increasing the competitiveness of the organic vegetables market; 3 Analyze the factors priority strategies for improving the competitiveness of the organic vegetables market. Porter's Generic Model and Analysis Analytical Hierarchy Process (AHP is used to determine the best strategy. The research found that organic vegetables marketing channels are still dominated by conventional market; the higher cost for intensive cultivation of organic vegetables. The main strategies are derived from the analysis is focusing on market delivery. There needs to be retailers of organic vegetables either modern or traditional to display these products. The establishment of organic vegetable outlets and online marketing that are not dependent on large retail (hypermarket become recommendations in this study. Bahasa Indonesia Abstrak: Kesadaran masyarakat tentang gaya hidup sehat memberi pilihan kepada masyarakat untuk memahami makanan yang mereka konsumsi. Pilihan sayuran organik merupakan salah satu alternatif untuk memiliki tubuh sehat dan gaya hidup sehat bagi masyarakat. Sayangnya, tidak banyak petani sayuran organik di Indonesia yang berhasil merebut pasar sayuran organik daripada non organic. Persaingan produk impor sayuran organik ke Indonesia membuat petani tidak bisa berkembang. Penelitian ini bertujuan untuk: 1 Menganalisis faktor-faktor yang

  17. Resistive switching characteristics of solution-processed organic-inorganic blended films for flexible memory applications

    Science.gov (United States)

    Baek, Il-Jin; Cho, Won-Ju

    2018-02-01

    We developed a hybrid organic-inorganic resistive random access memory (ReRAM) device that uses a solution-process to overcome the disadvantages of organic and inorganic materials for flexible memory applications. The drawbacks of organic and inorganic materials are a poor electrical characteristics and a lack of flexibility, respectively. We fabricated a hybrid organic-inorganic switching layer of ReRAM by blending HfOx or AlOx solution with PMMA solution and investigated the resistive switching behaviour in Ti/PMMA/Pt, Ti/PMMA-HfOx/Pt and Ti/PMMA-AlOx/Pt structures. It is found that PMMA-HfOx or PMMA-AlOx hybrid switching layer has a larger memory window, more stable durability and retention characteristics, and a better set/reset voltage distribution than PMMA layer. Further, it is confirmed that the flexibility of the PMMA-HfOx and PMMA-AlOx blended films was almost similar to that of the organic PMMA film. Thus, the solution-processed organic-inorganic blended films are considered a promising material for a non-volatile memory device on a flexible or wearable electronic system.

  18. Feminist Organizing in Rural Nicaragua: Assessing a Psychosocial Process to Promote Empowered Solidarity.

    Science.gov (United States)

    Dutt, Anjali

    2018-04-19

    This study examines a psychosocial process linking women's involvement in a grassroots women's organization with skills and experiences to promote empowered solidarity. Empowered solidarity is described as a process of increasing the sense of connection and capacity to create social transformation among a group of people united by interest in addressing a social issue. Data collected and analyzed for this research were 298 quantitative surveys conducted with two groups of women living in rural Nicaragua. One group of women were members of a grassroots feminist organization, and the other group lived in nearby communities where the organization did not offer programs. Findings document higher levels of leadership skills and sense of community, and lower levels of powerlessness among members of the organization. Additionally, tests of a process model using structural equation modeling provides support for a model that links involvement in the organization to women's increased interest in, capacity and experience in working to support women, broadly. Overall findings from this research are valuable to both community psychologists and groups seeking to enhance social justice and uphold feminist values of equity and community well-being. © Society for Community Research and Action 2018.

  19. Sub-wavelength patterning of organic monolayers via nonlinear processing with continuous-wave lasers

    Energy Technology Data Exchange (ETDEWEB)

    Mathieu, Mareike; Hartmann, Nils, E-mail: nils.hartmann@uni-due.de [Fakultaet fuer Chemie, Universitaet Duisburg-Essen, 45117 Essen (Germany); CeNIDE-Center for Nanointegration Duisburg-Essen, 47048 Duisburg (Germany); NETZ-NanoEnergieTechnikZentrum, 47048 Duisburg (Germany)

    2010-12-15

    In recent years, nonlinear processing with continuous-wave lasers has been demonstrated to be a facile means of rapid nanopatterning of organic monolayers down to the sub-100 nm range. In this study, we report on laser patterning of thiol-based organic monolayers with sub-wavelength resolution. Au-coated silicon substrates are functionalized with 1-hexadecanethiol. Irradiation with a focused beam of an Ar{sup +} laser operating at {lambda}=514 nm allows one to locally remove the monolayer. Subsequently, the patterns are transferred into the Au film via selective etching in a ferri-/ferrocyanide solution. Despite a 1/e{sup 2} spot diameter of about 2.8 {mu}m, structures with lateral dimensions down to 250 nm are fabricated. The underlying nonlinear dependence of the patterning process on laser intensity is traced back to the interplay between the laser-induced transient local temperature rise and the thermally activated desorption of the thiol molecules. A simple thermokinetic analysis of the data allows us to determine the effective kinetic parameters. These results complement our previous work on photothermal laser patterning of ultrathin organic coatings, such as silane-based organic monolayers, organo/silicon interfaces and supported membranes. A general introduction to nonlinear laser processing of organic monolayers is presented.

  20. Self-Organization and the Self-Assembling Process in Tissue Engineering

    Science.gov (United States)

    Eswaramoorthy, Rajalakshmanan; Hadidi, Pasha; Hu, Jerry C.

    2015-01-01

    In recent years, the tissue engineering paradigm has shifted to include a new and growing subfield of scaffoldless techniques which generate self-organizing and self-assembling tissues. This review aims to provide a cogent description of this relatively new research area, with special emphasis on applications toward clinical use and research models. Particular emphasis is placed on providing clear definitions of self-organization and the self-assembling process, as delineated from other scaffoldless techniques in tissue engineering and regenerative medicine. Significantly, during formation, self-organizing and self-assembling tissues display biological processes similar to those that occur in vivo. These help lead to the recapitulation of native tissue morphological structure and organization. Notably, functional properties of these tissues also approach native tissue values; some of these engineered tissues are already in clinical trials. This review aims to provide a cohesive summary of work in this field, and to highlight the potential of self-organization and the self-assembling process to provide cogent solutions to current intractable problems in tissue engineering. PMID:23701238

  1. A Marketing approach on how continuous processes improvement can contribute to hotel business Organic Growth

    OpenAIRE

    Ioana-Simona IVASCIUC; Gheorghe EPURAN

    2015-01-01

    Generating sustainable growth and profits is like finding a unicorn for most managers. Organic growth should be considered as an alternative for long-term growth in the hotel business. Designing the service process to deliver what customers expect from the hotel offer is a crucial component of encounter marketing. Hotels need to embrace the changes and ensure that their internal processes are aligned not just to current trends, but also to the expected future changes. Keeping u...

  2. IT-enabled Business Process Change in Private and in Public Sector Organizations

    OpenAIRE

    Jurisch, Marlen Christin

    2015-01-01

    Improving business process performance is still a top priority of CIOs. However, many organizations are daunted by the challenges and risks that business process change (BPC) imposes. The staggering failure rates of BPC projects signify that practitioners and researchers still lack a clear understanding of the determinants impacting BPC success. This thesis begins to address this gap by answering the research question: what are the determinants for successful IT-enabled BPC. In order to answe...

  3. Organizing the Financial and Economic Security of Business Processes of Innovation Development of Enterprise

    OpenAIRE

    Otenko Iryna P.; Komarkov Dmytriy V.; Shkreben Roman P.

    2017-01-01

    The article is aimed at analyzing ways and means of organizing the financial and economic security of business processes of innovation development of enterprise. The business processes of enterprise, which act as objects of managerial decision-making, are considered. It has been determined that the time for decision-making by directors is ensured as result not only of reactive but also proactive management, that is, one that involves modeling the problematic situations, related to business pr...

  4. Strategic-decision quality in public organizations : an information processing perspective

    OpenAIRE

    George, Bert; Desmidt, Sebastian

    2018-01-01

    textabstractThis study draws on information processing theory to investigate predictors of strategic-decision quality in public organizations. Information processing theory argues that (a) rational planning practices contribute to strategic-decision quality by injecting information into decision making and (b) decision makers contribute to strategic-decision quality by exchanging information during decision making. These assumptions are tested upon 55 Flemish pupil guidance centers. Rational ...

  5. Process performance and modelling of anaerobic digestion using source-sorted organic household waste

    DEFF Research Database (Denmark)

    Khoshnevisan, Benyamin; Tsapekos, Panagiotis; Alvarado-Morales, Merlin

    2018-01-01

    Three distinctive start-up strategies of biogas reactors fed with source-sorted organic fraction of municipal solid waste were investigated to reveal the most reliable procedure for rapid process stabilization. Moreover, the experimental results were compared with mathematical modeling outputs....... The combination of both experimental and modelling/simulation succeeded in optimizing the start-up process for anaerobic digestion of biopulp under mesophilic conditions....

  6. Information Security Monitoring Process Research in Russian Federation Banking System Organization

    Directory of Open Access Journals (Sweden)

    Anton Sergeevich Zaytsev

    2013-09-01

    Full Text Available In this article the author considers documents and scientific articles that should be used to configure monitoring and information security incident management process in an organization of banking system of Russia. Also key principles of monitoring configuration were marked up and a technique of monitoring configuration was proposed. Principles of monitoring system configuration were defined and a set of documents used to legitimate monitoring and information incident management process was considered.

  7. Modifying the organic/electrode interface in Organic Solar Cells (OSCs) and improving the efficiency of solution-processed phosphorescent Organic Light-Emitting Diodes (OLEDs)

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, Teng [Iowa State Univ., Ames, IA (United States)

    2012-01-01

    Organic semiconductors devices, such as, organic solar cells (OSCs), organic light-emitting diodes (OLEDs) and organic field-effect transistors (OFETs) have drawn increasing interest in recent decades. As organic materials are flexible, light weight, and potentially low-cost, organic semiconductor devices are considered to be an alternative to their inorganic counterparts. This dissertation will focus mainly on OSCs and OLEDs. As a clean and renewable energy source, the development of OSCs is very promising. Cells with 9.2% power conversion efficiency (PCE) were reported this year, compared to < 8% two years ago. OSCs belong to the so-called third generation solar cells and are still under development. While OLEDs are a more mature and better studied field, with commercial products already launched in the market, there are still several key issues: (1) the cost of OSCs/OLEDs is still high, largely due to the costly manufacturing processes; (2) the efficiency of OSCs/OLEDs needs to be improved; (3) the lifetime of OSCs/OLEDs is not sufficient compared to their inorganic counterparts; (4) the physics models of the behavior of the devices are not satisfactory. All these limitations invoke the demand for new organic materials, improved device architectures, low-cost fabrication methods, and better understanding of device physics. For OSCs, we attempted to improve the PCE by modifying the interlayer between active layer/metal. We found that ethylene glycol (EG) treated poly(3,4-ethylenedioxythiophene): polystyrenesulfonate (PEDOT: PSS) improves hole collection at the metal/polymer interface, furthermore it also affects the growth of the poly(3- hexylthiophene) (P3HT):phenyl-C61-butyric acid methyl ester (PCBM) blends, making the phase segregation more favorable for charge collection. We then studied organic/inorganic tandem cells. We also investigated the effect of a thin LiF layer on the hole-collection of copper phthalocyanine (CuPc)/C70-based small molecular OSCs. A

  8. MODELING THE PROCESS OF ASSIMILATION AND OPERATIONALIZATION OF THE CONCEPT OF MARKETING BY ROMANIAN LOCAL ORGANIZATIONS

    Directory of Open Access Journals (Sweden)

    Luminita Zait

    2015-07-01

    Full Text Available This paper proposes a model that wants to offer some pertinent answers about the process of assimilation and operationalization of the marketing concept in the practice of local organizations in Romania. Considering the reality of organizational practice in Romania, which revealed a lack of consistency in the approach of assimilation and operationalization of the marketing concept, the model tries to capture a range of factors that determine and explain this phenomenon. Reality shows that many Romanian organizations either do not perceive the need and importance of marketing in their activity or assimilate and develop a priori, actions carried out by transnational companies that do not meet the particular context of the Romanian market and / or of internal environment. The model attempts to capture the peculiarities of the process of assimilation and operationalization of the concept of marketing in local organizations and describe the characteristics of each identified organizational structures.

  9. Organic ice resists for 3D electron-beam processing: Instrumentation and operation

    DEFF Research Database (Denmark)

    Tiddi, William; Elsukova, Anna; Beleggia, Marco

    2018-01-01

    Organic vapors condensed into thin layers of ice on the surface of a cold substrate are exposed with an electron beam to create resist patterns for lithography applications. The entire spin- and development-free lithography process requires a single custom instrument. We report the design, material...... choice, implementation and operation of this apparatus. It is based on a scanning electron microscope fitted with an electron beam control system that is normally used for electron beam lithography in a multi-user open-access laboratory. The microscope was also equipped with a gas injection system......, a liquid nitrogen cooled cryostage, a temperature control system, and a load-lock. Three steps are required to initialize the apparatus for organic ice resist processing, and two steps are required to restore the apparatus for routine multi-user operations. Five steps are needed to create organic ice...

  10. Organization of school work in focus: the limits of antidemocratic inheritance and potential of participatory processes

    Directory of Open Access Journals (Sweden)

    Maria Vieira Silva

    2011-10-01

    Full Text Available Historically, democratic and participatory processes in the Brazilian society, and specifically in school, have been permeated by intermittences, weaknesses and resistances caused by multiple determinations. The text focuses on aspects concerningthe organization of education work through two lines of analysis: the first angle refers to the social constructs of structural and organic nature linked to relations of power andanti-democratic practices of the society in general. The second angle reference to a kindof ethnographic research, conducted within a public school in the Minas Gerais state. We seek to grasp the challenges on building practices and strategies in support of the participatory processes of the school community in the pedagogic project design and in the operation of the school board. We propose, with these analyses, to contribute withreflections on the status of teachers, as a subject, in the school organization throughconnections with work activities related to their everyday practice.

  11. Degrading organic micropollutants: The next challenge in the evolution of biological wastewater treatment processes

    Directory of Open Access Journals (Sweden)

    Naresh eSinghal

    2016-05-01

    Full Text Available Global water scarcity is driving the need for identifying new water source. Wastewater could be a potential water resource if appropriate treatment technologies could be developed. One of the barriers to obtaining high quality water from wastewater arises from the presence of organic micropollutants, which are biologically active at trace levels. Removal of these compounds from wastewater by current physico-chemical technologies is prohibitively expensive. While biological treatment processes are comparatively cheap, current systems are not capable of degrading the wide range of organic micropollutants present in wastewater. As current wastewater treatment processes were developed for treating conventional pollutants present at mg/L levels, degrading the ng/L levels of micropollutants will require a different approach to system design and operation. In this paper we discuss strategies that could be employed to develop biological wastewater treatment systems capable of degrading organic micropollutants.

  12. All solution processing of ITO-free organic solar cell modules directly on barrier foil

    DEFF Research Database (Denmark)

    Angmo, Dechan; Hösel, Markus; Krebs, Frederik C

    2012-01-01

    In this study, we demonstrate fully solution processed semi-transparent silver electrodes on flexible substrates having a sheet resistance as low as 5Ω/□ and transmittance of ∼30% at 550nm. We demonstrate the use of this electrode as a substitute for ITO in an inverted organic solar cell (OSC...

  13. Failure analysis in ITO-free all-solution processed organic solar cells

    NARCIS (Netherlands)

    Galagan, Y.; Eggenhuisen, T.M.; Coenen, M.J.J.; Biezemans, A.F.K.V.; Verhees, W.J.H.; Veenstra, S.C.; Groen, W.A.; Andriessen, R.; Janssen, R.A.J.

    2015-01-01

    In this paper we discuss a problem-solving methodology and present guidance for troubleshooting defects in ITO-free all-solution processed organic solar cells with an inverted cell architecture. A systematic approach for identifying the main causes of failures in devices is presented. Comprehensive

  14. Investigation on Self-Organization Processes in DC Generators by Synergetic Modeling

    Directory of Open Access Journals (Sweden)

    Ion Voncilă

    2014-09-01

    Full Text Available In this paper is suggested a new mathematical model, based on which it can be justified the self-excitation DC generators, either shunt or series excitation, by self-organization phenomena that appear to overcome threshold values (self-excitation in these generators is an avalanche process, a positive feedback, considered at first glance uncontrollable.

  15. Investigation on Self-Organization Processes in DC Generators by Synergetic Modeling

    OpenAIRE

    Ion Voncilă; Mădălin Costin; Răzvan Buhosu

    2014-01-01

    In this paper is suggested a new mathematical model, based on which it can be justified the self-excitation DC generators, either shunt or series excitation, by self-organization phenomena that appear to overcome threshold values (self-excitation in these generators is an avalanche process, a positive feedback, considered at first glance uncontrollable).

  16. The Socialization of Newcomers into Organizations: Integrating Learning and Social Exchange Processes

    Science.gov (United States)

    Korte, Russell F.

    2007-01-01

    Traditional views of socialization focus primarily on the passive learning by the newcomer of the expectations of the organization. Theorizing and research on cognitive learning and social exchange indicate that the socialization process is vastly more complex. This paper views socialization through the lenses of cognitive learning and social…

  17. The experimental studies of 137Cs elimination process from the organism of fish

    International Nuclear Information System (INIS)

    Volkova, O.M.; Belyajev, V.V.; Potrokhov, O.S.

    2003-01-01

    The influence of the ration of a feeding of fishes on the process of 137 Cs elimination from the organism was investigated. The inverse dependence between the mass of fishes and specific activity 137 Cs was found. The rations of the feeding of fishes make possible to lower the specific activity of fishes to the recommended level was determined

  18. A triphenylamine substituted quinacridone derivative for solution processed organic light emitting diodes

    NARCIS (Netherlands)

    Pilz da Cunha, M.; Do, T.T.; Yambem, S.D.; Pham, H.D.; Chang, S.; Manzhos, S.; Katoh, R.; Sonar, P.

    2018-01-01

    We report on a novel quinacridone derivative design, namely, 2,9-bis(4-(bis(4-methoxyphenyl)amino)phenyl)-5,12-bis(2-ethylhexyl)-5,12-dihydroquinolino[2,3-b]acridine-7,14-dione (TPA-QA-TPA) for possible use as a solution processable emissive layer in organic light emitting diodes (OLEDs). TPA-QA-TPA

  19. Anaerobic Digestion of the Organic Fraction of Municipal Solid Waste With Recirculation of Process Water

    DEFF Research Database (Denmark)

    Hartmann, H.; Angelidaki, Irini; Ahring, Birgitte Kiær

    2001-01-01

    A new concept of a wet anaerobic digestion treatment of the organic fraction of municipal solid waste (OFMSW) is investigated. Once the waste is diluted with water, the entire liquid fraction of the effluent is recirculated and used as process water for dilution of the waste. This enables a well...

  20. Detection of organic residues on poultry processing equipment surfaces by LED-induced fluorescence imaging

    Science.gov (United States)

    Organic residues on equipment surfaces in poultry processing plants can generate cross- contamination and increase the risk of unsafe food for consumers. This research was aimed to investigate the potential of LED-induced fluorescence imaging technique for rapid inspection of stainless steel proces...

  1. Retention-oxidation-adsorption process for emergent treatment of organic liquid spills.

    Science.gov (United States)

    Liu, Xianjun; Li, Yu; Zhang, Xingwang; Lei, Lecheng

    2011-11-15

    The feasibility and effectiveness of retention-oxidation-adsorption process (ROA) for the elimination of organic contaminants induced by chemical accidents were investigated in this study. Organobentonites (DTMA-, TTA-, CTMA- and OTMA-bentonite), potassium ferrate (Fe(VI)), ozone and granular activated carbon (GAC) were used as rapid and efficient materials in the treatment and recovery of organic liquid spills. Results indicated that the retention capacities of organobentonites (especially CTMA-bentonite) were much higher than that of natural bentonite towards the chosen organic compounds. Additionally, pH, oxidant dosage, initial concentration of contaminant and chemical structure had significant influences on the effectiveness of the oxidation process. In a pilot-scale experiment, the ferrate/GAC (F/G) and ozone/GAC (O/G) processes made a comparatively good performance in the treatment of wastewater containing aniline or nitrobenzene, with the removal efficiencies of the contaminants greater than 80%. Overall, the ROA process showed a high efficiency and steady operation in the removal of hazardous organic liquids and subsequent clean up of the contaminated site. Crown Copyright © 2011. Published by Elsevier B.V. All rights reserved.

  2. Online total organic carbon (TOC) monitoring for water and wastewater treatment plants processes and operations optimization

    Science.gov (United States)

    Assmann, Céline; Scott, Amanda; Biller, Dondra

    2017-08-01

    Organic measurements, such as biological oxygen demand (BOD) and chemical oxygen demand (COD) were developed decades ago in order to measure organics in water. Today, these time-consuming measurements are still used as parameters to check the water treatment quality; however, the time required to generate a result, ranging from hours to days, does not allow COD or BOD to be useful process control parameters - see (1) Standard Method 5210 B; 5-day BOD Test, 1997, and (2) ASTM D1252; COD Test, 2012. Online organic carbon monitoring allows for effective process control because results are generated every few minutes. Though it does not replace BOD or COD measurements still required for compliance reporting, it allows for smart, data-driven and rapid decision-making to improve process control and optimization or meet compliances. Thanks to the smart interpretation of generated data and the capability to now take real-time actions, municipal drinking water and wastewater treatment facility operators can positively impact their OPEX (operational expenditure) efficiencies and their capabilities to meet regulatory requirements. This paper describes how three municipal wastewater and drinking water plants gained process insights, and determined optimization opportunities thanks to the implementation of online total organic carbon (TOC) monitoring.

  3. Efficient electron injection from solution-processed cesium stearate interlayers in organic light-emitting diodes

    NARCIS (Netherlands)

    Wetzelaer, G. A. H.; Najafi, A.; Kist, R. J. P.; Kuik, M.; Blom, P. W. M.

    2013-01-01

    The electron-injection capability of solution-processed cesium stearate films in organic light-emitting diodes is investigated. Cesium stearate, which is expected to exhibit good solubility and film formation due to its long hydrocarbon chain, is synthesized using a straightforward procedure.

  4. Effects of hydrologic conditions on biogeochemical processes and organic pollutant degradation in salt marsh sediments

    Science.gov (United States)

    W. James Catallo

    2000-01-01

    This work addressed the influence of tidal vs. static hydrologic conditions on biogeochemical processes and the transformation of pollutant organic chemicals (eight representative N-, O-, and S-heterocycles (NOSHs) from coal chemicals, crude oils, and pyrogenic mixtures) in salt marsh sediments. The goals were to: (1) determine the effects of static (flooded, drained)...

  5. A Conceptual Framework of Corporate and Business Ethics across Organizations: Structures, Processes and Performance

    Science.gov (United States)

    Svensson, Goran; Wood, Greg

    2011-01-01

    Purpose: The objective of this paper is to introduce and describe a conceptual framework of corporate and business ethics across organizations in terms of ethical structures, ethical processes and ethical performance. Design/methodology/approach: A framework is outlined and positioned incorporating an ethical frame of reference in the field of…

  6. Morphology Development in Solution-Processed Functional Organic Blend Films: An In Situ Viewpoint

    KAUST Repository

    Richter, Lee J.; DeLongchamp, Dean M.; Amassian, Aram

    2017-01-01

    .0, to the Internet of things, to point-of-use heath care and elder care. The extreme sensitivity of the functional performance of organic films to structure and the general nonequilibrium nature of solution drying result in extreme processing-performance correlations

  7. Satisfaction with the organ donation process of brain dead donors' families in Korea.

    Science.gov (United States)

    Kim, H S; Yoo, Y S; Cho, O H

    2014-12-01

    The purpose of this study was to investigate the satisfaction of the families of brain dead donors with regard to donation processes as well as their emotions after the donation. A cross-sectional survey study was performed that included 45 families of brain-dead donors in 1 hospital-based organ procurement organization (HOPO) in Korea between February 2007 and April 2011. Donor willingness and desire in life was the most frequent reason organs were donated (34.5%), followed by the advice of family members or friends (31.0%). Satisfaction with the organ donation processes was 4.04 of 6 points. In each category, the satisfaction with the decision of donation was the highest (4.96 points) and the satisfaction with the procedure of donation was the lowest (3.07 points); of each question, the satisfaction of "information and help on funeral arrangements was enough" and "the process of preparing the relevant documents was cumbersome" was the lowest. "Missing" the dead person and "pride" were the most common emotions experienced after organ donation (69.0% and 62.1%, respectively), followed by "grief," "family coherence," and "guilt." Religious practices were observed to be most helpful for psychological stress relief after donation, followed by spending time with family and friends. Moreover, 24.1% responded that they had not yet overcome their suffering. Because donors' own willingness is the most common reason that families choose donation, it is necessary to remind the public of the importance of organ donation through education and public relations using mass communication approaches. Additionally, because the families felt grief and guilt as well as missing their loved ones and pride regarding their dead loved ones after organ donation, continuous and systematic supports are needed to promote their psychological stability. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

  8. Intensive care nurses' perceptions of their professional competence in the organ donor process: a national survey.

    Science.gov (United States)

    Meyer, Käthe; Bjørk, Ida Torunn; Eide, Hilde

    2012-01-01

    This paper is a report of a study that explored Norwegian intensive care nurses' perceptions of their professional competence to identify educational needs in the organ donor process. Intensive care professionals are requested to consider organ donation each time they care for patients with severe cerebral lesion to ensure donor organs for transplantation. The donor process challenges intensive care nurses' professional competence. Nurses' knowledge and experience may influence their professional competence in caring for organ donors and their relatives. METHODS.: A cross-sectional survey was conducted in all 28 Norwegian donor hospitals between October 2008 and January 2009. Intensive care nurses (N = 801) were invited to participate and the response rate was 71·4%. Dimensions of professional competence, learning needs and contextual and demographic variables were explored. Data were analysed using descriptive and inferential statistics. Few intensive care nurses had extensive experience of or competence and training in organ donation. Nurses working at university hospitals had more experience, but lesser training than nurses in local hospitals. Experience of donor acquisition had an impact on intensive care nurses' perceptions of their professional competence in the donor process. Discussions on the ward and educational input were seen as important for the further development of professional competence. Training provided by experienced colleagues and a culture that encourages discussion about aspects of the donor process can develop nurses' professional competence and communally defined professional practice. Educational input that cultivates various types of knowledge can be beneficial in organ donation. © 2011 The Authors. Journal of Advanced Nursing © 2011 Blackwell Publishing Ltd.

  9. Sourdough microbial community dynamics: An analysis during French organic bread-making processes.

    Science.gov (United States)

    Lhomme, Emilie; Urien, Charlotte; Legrand, Judith; Dousset, Xavier; Onno, Bernard; Sicard, Delphine

    2016-02-01

    Natural sourdoughs are commonly used in bread-making processes, especially for organic bread. Despite its role in bread flavor and dough rise, the stability of the sourdough microbial community during and between bread-making processes is debated. We investigated the dynamics of lactic acid bacteria (LAB) and yeast communities in traditional organic sourdoughs of five French bakeries during the bread-making process and several months apart using classical and molecular microbiology techniques. Sourdoughs were sampled at four steps of the bread-making process with repetition. The analysis of microbial density over 68 sourdough/dough samples revealed that both LAB and yeast counts changed along the bread-making process and between bread-making runs. The species composition was less variable. A total of six LAB and nine yeast species was identified from 520 and 1675 isolates, respectively. The dominant LAB species was Lactobacillus sanfranciscensis, found for all bakeries and each bread-making run. The dominant yeast species changed only once between bread-making processes but differed between bakeries. They mostly belonged to the Kazachstania clade. Overall, this study highlights the change of population density within the bread-making process and between bread-making runs and the relative stability of the sourdough species community during bread-making process. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. NOCHAR Polymers: An Aqueous and Organic Liquid Solidification Process for Cadarache LOR (Liquides Organiques Radioactifs) - 13195

    International Nuclear Information System (INIS)

    Vaudey, Claire-Emilie; Renou, Sebastien; Porco, Julien; Kelley, Dennis; Cochaud, Chantal; Serrano, Roger

    2013-01-01

    To handle the Very Low Level Waste (VLLW) and the Low Level Waste (LLW) in France, two options can be considered: the incineration at CENTRACO facility and the disposal facility on ANDRA sites. The waste acceptance in these radwaste routes is dependent upon the adequacy between the waste characteristics (physical chemistry and radiological) and the radwaste route specifications. If the waste characteristics are incompatible with the radwaste route specifications (presence of significant quantities of chlorine, fluorine, organic component etc or/and high activity limits), it is necessary to find an alternative solution that consists of a waste pre-treatment process. In the context of the problematic Cadarache LOR (Liquides Organiques Radioactifs) waste streams, two radioactive scintillation cocktails have to be treated. The first one is composed of organic liquids at 13.1 % (diphenyloxazol, mesitylene, TBP, xylene) and water at 86.9 %. The second one is composed of TBP at 8.6 % and water at 91.4 %. They contain chlorine, fluorine and sulphate and have got alpha/beta/gamma spectra with mass activities equal to some kBq.g -1 . Therefore, tritium is present and creates the second problematic waste stream. As a consequence, in order for disposal acceptance at the ANDRA site, it is necessary to pre-treat the waste. The NOCHAR polymers as an aqueous and organic liquid solidification process seem to be an adequate solution. Indeed, these polymers constitute an important variety of products applied to the treatment of radioactive aqueous and organic liquids (solvent, oil, solvent/oil mixing etc) and sludge through a mechanical and chemical solidification process. For Cadarache LOR, N910 and N960 respectively dedicated to the organic and aqueous liquids solidification are considered. With the N910, the organic waste solidification occurs in two steps. As the organic liquid travels moves through the polymer strands, the strands swell and immobilise the liquid. Then as the

  11. Reactive transport modeling of coupled inorganic and organic processes in groundwater

    Energy Technology Data Exchange (ETDEWEB)

    Brun, Adam

    1997-12-31

    The main goals of this project are to develop and apply a reactive transport code for simulation of coupled organic and inorganic processes in the pollution plume in the ground water down-gradient from the Vejen landfill, Denmark. The detailed field investigations in this aquifer have previously revealed a complex pattern of strongly interdependent organic and inorganic processes. These processes occur simultaneously in a flow and transport system where the mixing of reactive species is influenced by the rather complex geology in the vicinity of the landfill. The removal of organic matter is influenced by the presence of various electron acceptors that also are involved in various inorganic geochemical reactions. It was concluded from the investigations that degradation of organic matter, complexation, mineral precipitation and dissolution, ion-exchange and inorganic redox reactions, as a minimum, should be included in the formulation of the model. The coupling of the organic and inorganic processes is developed based on a literature study. All inorganic processes are as an approximation described as equilibriumm processes. The organic processes are described by a maximum degradation rate that is decreased according to the availability of the participants in the processes, the actual pH, and the presence of inhibiting species. The reactive transport code consists of three separate codes, a flow and transport code, a geochemical code, and a biodegradation code. An iterative solution scheme couples the three codes. The coupled code was successfully verified for simple problems for which analytical solutions exist. For more complex problems the code was tested on synthetic cases and expected plume behavior was successfully simulated. Application of the code to the Vejen landfill aquifer was successful to the degree that the redox zonation down-gradient from the landfill was simulated correctly and that several of the simulated plumes showed a reasonable agreement with

  12. Optimization Of PVDF-TrFE Processing Conditions For The Fabrication Of Organic MEMS Resonators.

    Science.gov (United States)

    Ducrot, Pierre-Henri; Dufour, Isabelle; Ayela, Cédric

    2016-01-21

    This paper reports a systematic optimization of processing conditions of PVDF-TrFE piezoelectric thin films, used as integrated transducers in organic MEMS resonators. Indeed, despite data on electromechanical properties of PVDF found in the literature, optimized processing conditions that lead to these properties remain only partially described. In this work, a rigorous optimization of parameters enabling state-of-the-art piezoelectric properties of PVDF-TrFE thin films has been performed via the evaluation of the actuation performance of MEMS resonators. Conditions such as annealing duration, poling field and poling duration have been optimized and repeatability of the process has been demonstrated.

  13. All solution processed organic thin film transistor-backplane with printing technology for electrophoretic display

    Science.gov (United States)

    Lee, Myung W.; Song, C.K.

    2012-01-01

    In this study, solution processes were developed for backplane using an organic thin film transistor (OTFT) as a driving device for an electrophoretic display (EPD) panel. The processes covered not only the key device of OTFTs but also interlayer and pixel electrodes. The various materials and printing processes were adopted to achieve the requirements of devices and functioning layers. The performance of OTFT of the backplane was sufficient to drive EPD sheet by producing a mobility of 0.12 cm2/v x sec and on/off current ratio of 10(5).

  14. Combinatorial techniques to efficiently investigate and optimize organic thin film processing and properties.

    Science.gov (United States)

    Wieberger, Florian; Kolb, Tristan; Neuber, Christian; Ober, Christopher K; Schmidt, Hans-Werner

    2013-04-08

    In this article we present several developed and improved combinatorial techniques to optimize processing conditions and material properties of organic thin films. The combinatorial approach allows investigations of multi-variable dependencies and is the perfect tool to investigate organic thin films regarding their high performance purposes. In this context we develop and establish the reliable preparation of gradients of material composition, temperature, exposure, and immersion time. Furthermore we demonstrate the smart application of combinations of composition and processing gradients to create combinatorial libraries. First a binary combinatorial library is created by applying two gradients perpendicular to each other. A third gradient is carried out in very small areas and arranged matrix-like over the entire binary combinatorial library resulting in a ternary combinatorial library. Ternary combinatorial libraries allow identifying precise trends for the optimization of multi-variable dependent processes which is demonstrated on the lithographic patterning process. Here we verify conclusively the strong interaction and thus the interdependency of variables in the preparation and properties of complex organic thin film systems. The established gradient preparation techniques are not limited to lithographic patterning. It is possible to utilize and transfer the reported combinatorial techniques to other multi-variable dependent processes and to investigate and optimize thin film layers and devices for optical, electro-optical, and electronic applications.

  15. Combinatorial Techniques to Efficiently Investigate and Optimize Organic Thin Film Processing and Properties

    Directory of Open Access Journals (Sweden)

    Hans-Werner Schmidt

    2013-04-01

    Full Text Available In this article we present several developed and improved combinatorial techniques to optimize processing conditions and material properties of organic thin films. The combinatorial approach allows investigations of multi-variable dependencies and is the perfect tool to investigate organic thin films regarding their high performance purposes. In this context we develop and establish the reliable preparation of gradients of material composition, temperature, exposure, and immersion time. Furthermore we demonstrate the smart application of combinations of composition and processing gradients to create combinatorial libraries. First a binary combinatorial library is created by applying two gradients perpendicular to each other. A third gradient is carried out in very small areas and arranged matrix-like over the entire binary combinatorial library resulting in a ternary combinatorial library. Ternary combinatorial libraries allow identifying precise trends for the optimization of multi-variable dependent processes which is demonstrated on the lithographic patterning process. Here we verify conclusively the strong interaction and thus the interdependency of variables in the preparation and properties of complex organic thin film systems. The established gradient preparation techniques are not limited to lithographic patterning. It is possible to utilize and transfer the reported combinatorial techniques to other multi-variable dependent processes and to investigate and optimize thin film layers and devices for optical, electro-optical, and electronic applications.

  16. Influence of harvesting and processing methods on organic viability of soybean seed

    Directory of Open Access Journals (Sweden)

    Đukanović Lana

    2000-01-01

    Full Text Available Organic viability of soybean seed for three soybean varieties - elite (Bosa, ZPS 015 and Nena depending on methods of manipulation with seeds during harvesting and processing phase were determined in this paper. Trial was conducted in Zemun Polje during 1999; manual and mechanized harvesting or processing methods were applied. Seed germination was tested using ISTA methods (Standard method and Cold test. Following parameters were evaluated: germination viability, germination, rate-speed of emergence, length of hypocotile and main root Rate-speed of emergence was based on number of emerged plants per day. Length of hypocotile or root and percent of germination determined vigour index. Based on obtained results it maybe concluded that methods of seed manipulation during harvesting or processing phase were influenced on soybean seed quality parameters evaluated. Ways of seed manipulation - methods evaluated were influenced organic viability of soybean seed by decreasing germination viability, total germination and length of main root.

  17. Anaerobic/oxic/anoxic granular sludge process as an effective nutrient removal process utilizing denitrifying polyphosphate-accumulating organisms.

    Science.gov (United States)

    Kishida, Naohiro; Kim, Juhyun; Tsuneda, Satoshi; Sudo, Ryuichi

    2006-07-01

    In a biological nutrient removal (BNR) process, the utilization of denitrifying polyphosphate-accumulating organisms (DNPAOs) has many advantages such as effective use of organic carbon substrates and low sludge production. As a suitable process for the utilization of DNPAOs in BNR, an anaerobic/oxic/anoxic granular sludge (AOAGS) process was proposed in this study. In spite of performing aeration for nitrifying bacteria, the AOAGS process can create anaerobic/anoxic conditions suitable for the cultivation of DNPAOs because anoxic zones exist inside the granular sludge in the oxic phase. Thus, DNPAOs can coexist with nitrifying bacteria in a single reactor. In addition, the usability of DNPAOs in the reactor can be improved by adding the anoxic phase after the oxic phase. These characteristics enable the AOAGS process to attain effective removal of both nitrogen and phosphorus. When acetate-based synthetic wastewater (COD: 600 mg/L, NH4-N: 60 mg/L, PO(4)-P: 10 mg/L) was supplied to a laboratory-scale sequencing batch reactor under the operation of anaerobic/oxic/anoxic cycles, granular sludge with a diameter of 500 microm was successfully formed within 1 month. Although the removal of both nitrogen and phosphorus was almost complete at the end of the oxic phase, a short anoxic period subsequent to the oxic phase was necessary for further removal of nitrogen and phosphorus. As a result, effluent concentrations of NH(4)-N, NO(x)-N and PO(4)-P were always lower than 1 mg/L. It was found that penetration depth of oxygen inside the granular sludge was approximately 100 microm by microsensor measurements. In addition, from the microbiological analysis by fluorescence in situ hybridization, existence depth of polyphosphate-accumulating organisms was further than the maximum oxygen penetration depth. The water quality data, oxygen profiles and microbial community structure demonstrated that DNPAOs inside the granular sludge may be responsible for denitrification in the

  18. Membrane Fouling Potential of Secondary Effluent Organic Matter (EfOM) from Conventional Activated Sludge Process

    KAUST Repository

    Wei, Chunhai; Amy, Gary L.

    2012-01-01

    Secondary effluent organic matter (EfOM) from a conventional activated sludge process was filtered through constant-pressure dead-end filtration tests with a sequential ultrafiltration (UF, molecular weight cut-off (MWCO) of 10k Dalton) and nanofiltration (NF, MWCO of 200 Dalton) array to investigate its membrane fouling potential. Advanced analytical methods including liquid chromatography with online carbon detection (LC-OCD) and fluorescent excitation-emission matrix (F-EEM) were employed for EfOM characterization. EfOM consisted of humic substances and building blocks, low molecular weight (LMW) neutrals, biopolymers (mainly proteins) and hydrophobic organics according to the sequence of their organic carbon fractions. The UF rejected only biopolymers and the NF rejected most humics and building blocks and a significant part of LMW neutrals. Simultaneous occurrence of cake layer and standard blocking during the filtration process of both UF and NF was identified according to constant-pressure filtration equations, which was possibly caused by the heterogeneous nature of EfOM with a wide MW distribution (several ten to several million Dalton). Thus the corresponding two fouling indices (kc for cake layer and ks for standard blocking) from UF and NF could characterize the fouling potential of macromolecular biopolymers and low to intermediate MW organics (including humics, building blocks, LMW neutrals), respectively. Compared with macromolecular biopolymers, low to intermediate MW organics exhibited a much higher fouling potential due to their lower molecular weight and higher concentration.

  19. Fouling Characteristics of Dissolved Organic Matter in Papermaking Process Water on Polyethersulfone Ultrafiltration Membranes

    Directory of Open Access Journals (Sweden)

    Wenpeng Su

    2015-07-01

    Full Text Available In the papermaking industry, closure of process water (whitewater circuits has been used to reduce fresh water consumption. Membrane separation technology has potential for use in treating process water for recirculation. The purpose of this study was to reveal the fouling characteristics of a polyethersulfone (PES ultrafiltration membrane caused by dissolved organic matter (DOM in process water. Ultrafiltration membranes (UF and DAX ion exchange resins were applied to characterize the molecular weight (MW and hydrophilicity distribution of DOM. The interactions between various fractions of DOM and a PES ultrafiltration membrane were investigated. The membrane fouling characteristics were elucidated by examining the filtration resistances and linearized Herman’s blocking models. The results demonstrated that the membrane was fouled significantly by much of the MW distribution. The membrane was fouled more significantly by the low MW fraction rather than the high MW fraction. The filtration resistances and the fitted equation of Hermia’s laws indicated that hydrophilic organics were the main foulants. The hydrophilic organics partially block the membrane pores and form intermediate blocking, reducing the effective filtration area, while the hydrophobic organics form a gel layer or cake on the surface of the membrane.

  20. Burning transformations: Fire history effects on organic matter processing from hillslopes to streams

    Science.gov (United States)

    Barnes, R. T.; Gilbertson, A.; Maxwell, K.

    2017-12-01

    Disturbance strongly regulates material and energy flows, changing ecosystem pattern and process. An increase in the size and severity of fire, particularly in the Intermountain West, over the last several decades is expected to continue due to a warming climate. Predicting how fire will alter the net ecosystem carbon balance requires us to understand how carbon is stored, processed, and transferred. Here we present results from paired watersheds focused on five 2002 severe fires in Colorado to examine how organic matter is processed along the hillslope and within the stream. Comparing soil samples and water extractable organic matter (WEOM) between burned and unburned sites illustrates the impact of fire: burned soils have 50% organic matter (OM) content as unburned soils, regardless of geomorphic position. While a smaller pool, soil OM (SOM) in burned sites is more susceptible to microbial degradation (pmineral rich, organic poor, portion of the soil. Interestingly, the systematic shifts in OM amounts and quality (as measured by SUVA, E2:E3, and fluorescence) within the terrestrial system in response to fire, are not seen in stream exports. As such, while there are significant relationships (p<0.05) between stream DOM quality, DOM bioavailability, and stream metabolism, burned watersheds are not exporting DOM that is more bioavailable. In addition, despite different terrestrial OM pools, burned and unburned watersheds export statistically similar amounts of DOM per unit area, suggesting that a larger fraction of OM is transferred from the terrestrial to aquatic ecosystem within fire affected landscapes.

  1. Linking geochemical processes in mud volcanoes with arsenic mobilization driven by organic matter.

    Science.gov (United States)

    Liu, Chia-Chuan; Kar, Sandeep; Jean, Jiin-Shuh; Wang, Chung-Ho; Lee, Yao-Chang; Sracek, Ondra; Li, Zhaohui; Bundschuh, Jochen; Yang, Huai-Jen; Chen, Chien-Yen

    2013-11-15

    The present study deals with geochemical characterization of mud fluids and sediments collected from Kunshuiping (KSP), Liyushan (LYS), Wushanting (WST), Sinyangnyuhu (SYNH), Hsiaokunshui (HKS) and Yenshuikeng (YSK) mud volcanoes in southwestern Taiwan. Chemical constituents (cations, anions, trace elements, organic carbon, humic acid, and stable isotopes) in both fluids and mud were analyzed to investigate the geochemical processes and spatial variability among the mud volcanoes under consideration. Analytical results suggested that the anoxic mud volcanic fluids are highly saline, implying connate water as the probable source. The isotopic signature indicated that δ(18)O-rich fluids may be associated with silicate and carbonate mineral released through water-rock interaction, along with dehydration of clay minerals. Considerable amounts of arsenic in mud irrespective of fluid composition suggested possible release through biogeochemical processes in the subsurface environment. Sequential extraction of As from the mud indicated that As was mostly present in organic and sulphidic phases, and adsorbed on amorphous Mn oxyhydroxides. Volcanic mud and fluids are rich in organic matter (in terms of organic carbon), and the presence of humic acid in mud has implications for the binding of arsenic. Functional groups of humic acid also showed variable sources of organic matter among the mud volcanoes being examined. Because arsenate concentration in the mud fluids was found to be independent from geochemical factors, it was considered that organic matter may induce arsenic mobilization through an adsorption/desorption mechanism with humic substances under reducing conditions. Organic matter therefore plays a significant role in the mobility of arsenic in mud volcanoes. Copyright © 2012 Elsevier B.V. All rights reserved.

  2. Charge transfer processes in hybrid solar cells composed of amorphous silicon and organic materials

    Energy Technology Data Exchange (ETDEWEB)

    Schaefer, Sebastian; Neher, Dieter [Universitaet Potsdam, Inst. Physik u. Astronomie, Karl-Liebknecht-Strasse 24/25, 14467 Potsdam-Golm (Germany); Schulze, Tim; Korte, Lars [Helmholtz Zentrum Berlin, Inst. fuer Silizium Photovoltaik, Kekulestrasse 5, 12489 Berlin (Germany)

    2011-07-01

    The efficiency of hybrid solar cells composed of organic materials and amorphous hydrogenated silicon (a-Si:H) strongly depends upon the efficiency of charge transfer processes at the inorganic-organic interface. We investigated the performance of devices comprising an ITO/a-Si:H(n-type)/a-Si:H(intrinsic)/organic/metal multilayer structure and using two different organic components: zinc phthalocyanine (ZnPc) and poly(3-hexylthiophene) (P3HT). The results show higher power conversion- and quantum efficiencies for the P3HT based cells, compared to ZnPc. This can be explained by larger energy-level offset at the interface between the organic layer and a-Si:H, which facilitates hole transfer from occupied states in the valence band tail to the HOMO of the organic material and additionally promotes exciton splitting. The performance of the a-Si:H/P3HT cells can be further improved by treatment of the amorphous silicon surface with hydrofluoric acid (HF) and p-type doping of P3HT with F4TCNQ. The improved cells reached maximum power conversion efficiencies of 1%.

  3. Process options for treatment of organic containing ILWs by wet oxidation

    International Nuclear Information System (INIS)

    Holman, D.J.

    1989-01-01

    The process chemistry, applications and experience with several wet oxidation options are reviewed along with criteria for the selection of viable systems and plant designs, covering a range of organic wastes, including solvents, cellulosic filters, chelant decontamination reagents and ion exchange resins. The use of hydrogen peroxide to treat water-cooled reactor residues containing mixed inorganic and organic filter materials with ion exchange resins is examined in further detail along with treatment of secondary arisings. The technical and financial justifications for treatment are examined along with the engineering requirements to retro-fit the required plant to an existing cement encapsulation facility. (author)

  4. Design and optimization of a novel organic Rankine cycle with improved boiling process

    DEFF Research Database (Denmark)

    Andreasen, Jesper Graa; Larsen, U.; Knudsen, Thomas

    2015-01-01

    to improve the boiling process. Optimizations are carried out for eight hydrocarbon mixtures for hot fluid inlet temperatures at 120 °C and 90 °C, using a genetic algorithm to determine the cycle conditions for which the net power output is maximized. The most promising mixture is an isobutane....../pentane mixture which, for the 90 °C hot fluid inlet temperature case, achieves a 14.5% higher net power output than an optimized organic Rankine cycle using the same mixture. Two parameter studies suggest that optimum conditions for the organic split-cycle are when the temperature profile allows the minimum...

  5. An investigation and an accessment of organic cotton production and processing in developing countries (VB)

    DEFF Research Database (Denmark)

    Persson, Frida; Andersen, Lasse Kragh; Looms, Majken

    1999-01-01

    as important is that the locals participate on all levels of the project, so they feel responsible for the project and are able to run it themselves when the donor withdraws from the project after some time.Our conclusion is that implementing organic cotton production and organic cotton processing in Zimbabwe...... and Mozambique is a difficult but not impossible task, but a challenging way of improving the environmental impacts of todays conventional cotton production. Completing the manufacturing of cotton in the developing countries will enhance the economy of the country and thus the living standards of the population....

  6. EMPLOYEE INVOLVEMENT IN A CHANGE PROCESS - A CASE STUDY FOR ROMANIAN ORGANIZATIONS

    Directory of Open Access Journals (Sweden)

    Prediscan Mariana

    2015-07-01

    Full Text Available Innovation, competitive advantage, change are some concepts that should be on every organization's agenda, due to the fact the global market leads to global competition so in order to increase the market share, turnover or profit organizations have to incorporate those concepts in their strategies. The outside environment is very unstable and things are evolving very fast so managers from all levels have to acknowledge the importance of change and to identify as soon as possible several new ideas that should be the subject of different change processes. Openness to organizational change has become a mandatory feature for those organizations that want to survive and adapt to the external pressure, helping them to be efficient. Even if in many cases managers are the initiators of change, this process is very complex and needs support and involvement from all the members of the organization, so the employee's attitude and commitment to change is crucial. In many cases employees have a negative attitude towards change and manifest a strong resistance, due to the fact that they are not consulted and are not involved in the process of the identification for the need of change. Without understanding and knowing very well what it is expected from them, employees are afraid of the unknown and prefer to perform their tasks as they did before. Creating a climate and a culture for change is very important, because like this change will be something normal, continuous and people will feel comfortable with any change initiatives, without being surprised, confused or scared. Even if any change process should improve the current state of the organization, sometimes change efforts fail because the ones that resist change are stronger than the ones supporting change. The purpose of this paper is to analyze how often are Romanian employees involved in the processes of change and how important is the role they play. We have also tried to see the Romanian manager

  7. Process based modelling of soil organic carbon redistribution on landscape scale

    Science.gov (United States)

    Schindewolf, Marcus; Seher, Wiebke; Amorim, Amorim S. S.; Maeso, Daniel L.; Jürgen, Schmidt

    2014-05-01

    Recent studies have pointed out the great importance of erosion processes in global carbon cycling. Continuous erosion leads to a massive loss of top soils including the loss of organic carbon accumulated over long time in the soil humus fraction. Lal (2003) estimates that 20% of the organic carbon eroded with top soils is emitted into atmosphere, due to aggregate breakdown and carbon mineralization during transport by surface runoff. Furthermore soil erosion causes a progressive decrease of natural soil fertility, since cation exchange capacity is associated with organic colloids. As a consequence the ability of soils to accumulate organic carbon is reduced proportionately to the drop in soil productivity. The colluvial organic carbon might be protected from further degradation depending on the depth of the colluvial cover and local decomposing conditions. Some colluvial sites can act as long-term sinks for organic carbon. The erosional transport of organic carbon may have an effect on the global carbon budget, however, it is uncertain, whether erosion is a sink or a source for carbon in the atmosphere. Another part of eroded soils and organic carbon will enter surface water bodies and might be transported over long distances. These sediments might be deposited in the riparian zones of river networks. Erosional losses of organic carbon will not pass over into atmosphere for the most part. But soil erosion limits substantially the potential of soils to sequester atmospheric CO2 by generating humus. The present study refers to lateral carbon flux modelling on landscape scale using the process based EROSION 3D soil loss simulation model, using existing parameter values. The selective nature of soil erosion results in a preferentially transport of fine particles while less carbonic larger particles remain on site. Consequently organic carbon is enriched in the eroded sediment compared to the origin soil. For this reason it is essential that EROSION 3D provides the

  8. Use of an integrated biophysical process for the treatment of halo- and nitro- organic wastes

    Directory of Open Access Journals (Sweden)

    Liron Shoshani

    2017-07-01

    Full Text Available This study assessed the use of an integrated biophysical process incorporating the addition of powdered activated carbon (PAC to a dual-sludge biological process, in order to improve the removal of problematic contaminants from complex herbicides production wastewater. The main focus was on the removal of nitrogen compounds, total organic carbon (TOC, and halogenated organics (AOX. The dual-sludge pilot setup comprised a conventional activated sludge (CAS system followed by a membrane bioreactor (MBR system. The dilution ratio of raw wastewater was gradually decreased (with groundwater from 0.8 to 0 (no dilution, and PAC was added in the last phase of the study to maintain an equilibrium concentration of 2000 mg/L. PAC addition stimulated a high and steady removal (98% of the ammoniacal nitrogen, conforming to the sea discharge limit of 5 mg/L. However, the effluent concentrations of total nitrogen, TOC, and AOX were still above the stringent discharge limits of 20, 100 and 0.5 mg/L respectively. Furthermore, it was shown that synergistic effect of various toxic organic compounds, rather than mineral salinity, was the major cause for the acute inhibitions of nitrification and AOX removal. The study showed that the proposed process can function as an efficient treatment system for the complex wastewater typically produced in the herbicide industry, however, it is recommended that complementary physico-chemical treatment steps be added to the treatment process.

  9. Study of organic acids in Schisandrae Chinensis Fructus after vinegar processing.

    Science.gov (United States)

    Yin, Fangzhou; Dai, Hui; Li, Lin; Lu, Tuling; Li, Weidong; Cai, Baochang; Yin, Wu

    2017-10-01

    The ripened fruit of Schisandrae Chinensis Fructus has unique medical properties in Chinese medicine. It is commonly used after vinegar steaming. Vinegar steaming changes the color of Schisandrae Chinensis Fructus from red to black and enhances its acidic and astringent properties. Lignans are the well-investigated components in this herb. However, Schisandrae Chinensis Fructus is acidic in the theory of Chinese medicine, and whether vinegar processing changes its organic acid components remains largely unknown. In this study, the organic acids in this herb were derived by the method of methyl esterification, and further analyzed by gas chromatography with mass spectrometry. A total of 39 organic acid compounds were identified. Interestingly, Schisandrae Chinensis Fructus after vinegar processing showed a significant increase in the content of levulinic acid as compared to the unprocessed ones. Pharmacological experiments demonstrated that levulinic acid inhibited the contractility of isolated intestine and had an inhibitory effect on the excessive hyperfunction of small intestinal propulsion. Moreover, the extracts of vinegar-processed Schisandrae Chinensis Fructus had a stronger inhibitory on the excessive hyperfunction of small intestinal propulsion than that of unprocessed ones. Taken together, this study offers novel insight into the effect of Schisandrae Chinensis Fructus after vinegar processing. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Organic Light-Emitting Diodes on Solution-Processed Graphene Transparent Electrodes

    KAUST Repository

    Wu, Junbo

    2010-01-26

    Theoretical estimates indicate that graphene thin films can be used as transparent electrodes for thin-film devices such as solar cells and organic light-emitting diodes, with an unmatched combination of sheet resistance and transparency. We demonstrate organic light-emitting diodes with solution-processed graphene thin film transparent conductive anodes. The graphene electrodes were deposited on quartz substrates by spincoating of an aqueous dispersion of functionalized graphene, followed by a vacuum anneal step to reduce the sheet resistance. Small molecular weight organic materials and a metal cathode were directly deposited on the graphene anodes, resulting in devices with a performance comparable to control devices on indium-tin-oxide transparent anodes. The outcoupling efficiency of devices on graphene and indium-tin-oxide is nearly identical, in agreement with model predictions. © 2010 American Chemical Society.

  11. Cooking processes increase bioactive compounds in organic and conventional green beans.

    Science.gov (United States)

    Lima, Giuseppina Pace Pereira; Costa, Sergio Marques; Monaco, Kamila de Almeida; Uliana, Maira Rodrigues; Fernandez, Roberto Morato; Correa, Camila Renata; Vianello, Fabio; Cisneros-Zevallos, Luis; Minatel, Igor Otavio

    2017-12-01

    The influence of cooking methods on chlorophyl, carotenoids, polyamines, polyphenols contents and antioxidant capacity were analyzed in organic and conventional green beans. The initial raw material had a higher content of chlorophyl and total phenolics in conventional green beans, whereas organic cultive favored flavonoid content and antioxidant capacity. Polyamines and carotenoids were similar for the two crop systems. After the cooking process, carotenoids (β-carotene, lutein and zeaxanthin) increased. Microwave heating favored the enhancement of some polar compounds, whereas pressure cooking favored carotenoids. When we used the estimation of the radical scavenging activity by electron spin resonance (ESR) spectroscopy, a reduction of the DPPH radical signal in the presence of green bean extracts was observed, regardless of the mode of cultivation. The highest reduction of the ESR signal ocurred for microwave cooking in organic and conventional green beans, indicating a higher availability of antioxidants with this type of heat treatment.

  12. On the self-organizing process of large scale shear flows

    Energy Technology Data Exchange (ETDEWEB)

    Newton, Andrew P. L. [Department of Applied Maths, University of Sheffield, Sheffield, Yorkshire S3 7RH (United Kingdom); Kim, Eun-jin [School of Mathematics and Statistics, University of Sheffield, Sheffield, Yorkshire S3 7RH (United Kingdom); Liu, Han-Li [High Altitude Observatory, National Centre for Atmospheric Research, P. O. BOX 3000, Boulder, Colorado 80303-3000 (United States)

    2013-09-15

    Self organization is invoked as a paradigm to explore the processes governing the evolution of shear flows. By examining the probability density function (PDF) of the local flow gradient (shear), we show that shear flows reach a quasi-equilibrium state as its growth of shear is balanced by shear relaxation. Specifically, the PDFs of the local shear are calculated numerically and analytically in reduced 1D and 0D models, where the PDFs are shown to converge to a bimodal distribution in the case of finite correlated temporal forcing. This bimodal PDF is then shown to be reproduced in nonlinear simulation of 2D hydrodynamic turbulence. Furthermore, the bimodal PDF is demonstrated to result from a self-organizing shear flow with linear profile. Similar bimodal structure and linear profile of the shear flow are observed in gulf stream, suggesting self-organization.

  13. Technological and life cycle assessment of organics processing odour control technologies

    Energy Technology Data Exchange (ETDEWEB)

    Bindra, Navin [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada); Dubey, Brajesh, E-mail: bkdubey@civil.iitkgp.ernet.in [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada); Environmental Engineering Division, Department of Civil Engineering, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India); Dutta, Animesh [School of Engineering, University of Guelph, 50 Stone Road East, Guelph, Ontario N1G2W1 (Canada)

    2015-09-15

    As more municipalities and communities across developed world look towards implementing organic waste management programmes or upgrading existing ones, composting facilities are emerging as a popular choice. However, odour from these facilities continues to be one of the most important concerns in terms of cost & effective mitigation. This paper provides a technological and life cycle assessment of some of the different odour control technologies and treatment methods that can be implemented in organics processing facilities. The technological assessment compared biofilters, packed tower wet scrubbers, fine mist wet scrubbers, activated carbon adsorption, thermal oxidization, oxidization chemicals and masking agents. The technologies/treatment methods were evaluated and compared based on a variety of operational, usage and cost parameters. Based on the technological assessment it was found that, biofilters and packed bed wet scrubbers are the most applicable odour control technologies for use in organics processing faculties. A life cycle assessment was then done to compare the environmental impacts of the packed-bed wet scrubber system, organic (wood-chip media) bio-filter and inorganic (synthetic media) bio-filter systems. Twelve impact categories were assessed; cumulative energy demand (CED), climate change, human toxicity, photochemical oxidant formation, metal depletion, fossil depletion, terrestrial acidification, freshwater eutrophication, marine eutrophication, terrestrial eco-toxicity, freshwater eco-toxicity and marine eco-toxicity. The results showed that for all impact categories the synthetic media biofilter had the highest environmental impact, followed by the wood chip media bio-filter system. The packed-bed system had the lowest environmental impact for all categories. - Highlights: • Assessment of odour control technologies for organics processing facilities. • Comparative life cycle assessment of three odour control technologies was conducted

  14. CLASSIFICATION OF PROCESSES OF REPRODUCTION OF FIXED CAPITAL OF THE AGRICULTURAL ORGANIZATIONS

    Directory of Open Access Journals (Sweden)

    Anatoly Shamin

    2018-04-01

    Full Text Available It is described that questions of economic growth, the advancing investments, preservations of food security of the country demand from economy of the Russian Federation of an exit to the new level of functioning that is impossible without effective management of process of reproduction of fixed capital in the agricultural organizations. Materials and methods. In work the analysis of the treatments of the concepts "reproduction type", "type of reproduction", "reproduction method", "reproduction form" existing in the Russian scientific community was carried out, the conclusion is drawn on considerable confusion in terminology, need of identification of these concepts is noted. Authors analyzed essence of these concepts, author's treatments of the studied definitions are given. It is separately emphasized that from the point of view of authors ascertaining of existence of certain types, forms and types of reproduction can be made only after carrying out the corresponding analysis of real processes. Results. In the article the problem of a typologization of processes of reproduction of fixed capital on the basis of change of indicators of the general and average power of elements of fixed capital on the basis of these forms 17-APK annual accounting reports of the agrarian and industrial complexes organizations of the Nizhny Novgorod Region for 2010-2013 were solved. On the basis of the cluster analysis of their values the main 9 types of the organizations for these indicators were allocated. Discussion. On the basis of the analysis of change of types of the organizations 8 types of reproduction of fixed capital on change of indicators of power were allocated, their prevalence is analyzed. It is noted that the agricultural organizations of the Nizhny Novgorod Region generally increase as average, and the specific power of the fixed capital. Conclusion. In the conclusion authors noted the further perspective areas of work on this subject.

  15. Linking geochemical processes in mud volcanoes with arsenic mobilization driven by organic matter

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Chia-Chuan; Kar, Sandeep [Department of Earth Sciences, National Cheng Kung University, Tainan, Taiwan (China); Jean, Jiin-Shuh, E-mail: jiinshuh@mail.ncku.edu.tw [Department of Earth Sciences, National Cheng Kung University, Tainan, Taiwan (China); Wang, Chung-Ho [Institute of Earth Sciences, Academia Sinica, Taipei, Taiwan (China); Lee, Yao-Chang [National Synchrotron Radiation Research Center, Hsinchu 30076, Taiwan (China); Sracek, Ondra [OPV s.r.o. (Groundwater Protection Ltd.), Bělohorská 31, 169 00 Praha 6 (Czech Republic); Department of Geology, Faculty of Science, Palacký University, 17. listopadu 12, 771 46 Olomouc (Czech Republic); Li, Zhaohui [Department of Earth Sciences, National Cheng Kung University, Tainan, Taiwan (China); Department of Geosciences, University of Wisconsin – Parkside, Kenosha, WI 53144 (United States); Bundschuh, Jochen [Department of Earth Sciences, National Cheng Kung University, Tainan, Taiwan (China); Faculty of Engineering and Surveying and National Centre for Engineering in Agriculture, The University of Southern Queensland, Toowoomba (Australia); Yang, Huai-Jen [Department of Earth Sciences, National Cheng Kung University, Tainan, Taiwan (China); Chen, Chien-Yen [Department of Earth and Environmental Sciences, National Chung Cheng University, Chiayi 621, Taiwan (China)

    2013-11-15

    Highlights: ► Study represents geochemical characteristics and their spatial variability among six mud volcanoes of southern Taiwan. ► Anoxic mud volcanic fluids containing high NaCl imply connate water as the possible source. ► δ{sup 18}O-rich fluids is associated with silicate and carbonate mineral released through water–rock interaction. ► High As content in mud and its sequential extraction showed mostly adsorbed As on organic and sulphidic phases. ► Organic matter specially humic acid showed redox dependence and it may play an important role in binding and mobility of arsenic. -- Abstract: The present study deals with geochemical characterization of mud fluids and sediments collected from Kunshuiping (KSP), Liyushan (LYS), Wushanting (WST), Sinyangnyuhu (SYNH), Hsiaokunshui (HKS) and Yenshuikeng (YSK) mud volcanoes in southwestern Taiwan. Chemical constituents (cations, anions, trace elements, organic carbon, humic acid, and stable isotopes) in both fluids and mud were analyzed to investigate the geochemical processes and spatial variability among the mud volcanoes under consideration. Analytical results suggested that the anoxic mud volcanic fluids are highly saline, implying connate water as the probable source. The isotopic signature indicated that δ{sup 18}O-rich fluids may be associated with silicate and carbonate mineral released through water–rock interaction, along with dehydration of clay minerals. Considerable amounts of arsenic in mud irrespective of fluid composition suggested possible release through biogeochemical processes in the subsurface environment. Sequential extraction of As from the mud indicated that As was mostly present in organic and sulphidic phases, and adsorbed on amorphous Mn oxyhydroxides. Volcanic mud and fluids are rich in organic matter (in terms of organic carbon), and the presence of humic acid in mud has implications for the binding of arsenic. Functional groups of humic acid also showed variable sources of

  16. Carbon Isotope Systematics in Mineral-Catalyzed Hydrothermal Organic Synthesis Processes at High Temperature and Pressures

    Science.gov (United States)

    Fu, Qi; Socki, R. A.; Niles, Paul B.

    2011-01-01

    Observation of methane in the Martian atmosphere has been reported by different detection techniques. Reduction of CO2 and/or CO during serpentization by mineral surface catalyzed Fischer-Tropsch Type (FTT) synthesis may be one possible process responsible for methane generation on Mars. With the evidence a recent study has discovered for serpentinization in deeply buried carbon rich sediments, and more showing extensive water-rock interaction in Martian history, it seems likely that abiotic methane generation via serpentinization reactions may have been common on Mars. Experiments involving mineral-catalyzed hydrothermal organic synthesis processes were conducted at 750 C and 5.5 Kbars. Alkanes, alcohols and carboxylic acids were identified as organic compounds. No "isotopic reversal" of delta C-13 values was observed for alkanes or carboxylic acids, suggesting a different reaction pathway than polymerization. Alcohols were proposed as intermediaries formed on mineral surfaces at experimental conditions. Carbon isotope data were used in this study to unravel the reaction pathways of abiotic formation of organic compounds in hydrothermal systems at high temperatures and pressures. They are instrumental in constraining the origin and evolution history of organic compounds on Mars and other planets.

  17. Novel bioevaporation process for the zero-discharge treatment of highly concentrated organic wastewater.

    Science.gov (United States)

    Yang, Benqin; Zhang, Lei; Lee, Yongwoo; Jahng, Deokjin

    2013-10-01

    A novel process termed as bioevaporation was established to completely evaporate wastewater by metabolic heat released from the aerobic microbial degradation of the organic matters contained in the highly concentrated organic wastewater itself. By adding the glucose solution and ground food waste (FW) into the biodried sludge bed, the activity of the microorganisms in the biodried sludge was stimulated and the water in the glucose solution and FW was evaporated. As the biodegradable volatile solids (BVS) concentration in wastewater increased, more heat was produced and the water removal ratio increased. When the volatile solids (VS) concentrations of both glucose and ground FW were 120 g L(-1), 101.7% and 104.3% of the added water was removed, respectively, by completely consuming the glucose and FW BVS. Therefore, the complete removal of water and biodegradable organic contents was achieved simultaneously in the bioevaporation process, which accomplished zero-discharge treatment of highly concentrated organic wastewater. Copyright © 2013 Elsevier Ltd. All rights reserved.

  18. Organization and post-transcriptional processing of the psb B operon from chloroplasts of Populus deltoides.

    Science.gov (United States)

    Dixit, R; Trivedi, P K; Nath, P; Sane, P V

    1999-09-01

    Chloroplast genes are typically organized into polycistronic transcription units that give rise to complex sets of mono- and oligo-cistronic overlapping RNAs through a series of processing steps. The psbB operon contains genes for the PSII (psbB, psbT, psbH) and cytochrome b(6)f (petB and petD) complexes which are needed in different amounts during chloroplast biogenesis. The functional significance of gene organization in this polycistronic unit, containing information for two different complexes, is not known and is of interest. To determine the organization and expression of these complexes, studies have been carried out on crop plants by different groups, but not much information is known about trees. We present the nucleotide sequences of PSII genes and RNA profiles of the genes located in the psbB operon from Populus deltoides, a tree species. Although the gene organization of this operon in P. deltoides is similar to that in other species, a few variations have been observed in the processing scheme.

  19. Achievements and barriers in the organ donation process: a critical analysis of donation coordinators' discourse.

    Science.gov (United States)

    Mercado-Martínez, Francisco J; Díaz-Medina, Blanca A; Hernández-Ibarra, Eduardo

    2013-09-01

    Donation coordinators play an important role in the success or failure of organ donation and transplant programs. Nevertheless, these professionals' perspectives and practices have hardly been explored, particularly in low- and middle-income countries. To examine donation coordinators' discourse on the organ donation process and the barriers they perceive. A critical qualitative study was carried out in Guadalajara, Mexico. Twelve donation coordinators from public and private hospitals participated. DATA GATHERING AND ANALYSIS: Data were gathered by using semistructured interviews and critical discourse analysis. Participants indicated that partial results have been achieved in deceased organ donation. Concomitantly, multiple obstacles have adversely affected the process and outcomes: at the structural level, the fragmentation of the health system and the scarcity of financial and material resources; at the relational level, nonegalitarian relationships between coordinators and hospital personnel; at the ideational level, the transplant domain and its specialists overshadow the donation domain and its coordinators. Negative images are associated with donation coordinators. Organ donation faces structural, relational, and ideational barriers; hence, complex interventions should be undertaken. Donation coordinators also should be recognized by the health system.

  20. Aspects of Information Architecture involved in process mapping in Military Organizations under the semiotic perspective

    Directory of Open Access Journals (Sweden)

    Mac Amaral Cartaxo

    2016-04-01

    Full Text Available Introduction: The description of the processes to represent the activities in an organization has important call semiotic, It is the flowcharts of uses, management reports and the various forms of representation of the strategies used. The subsequent interpretation of the organization's employees involved in learning tasks and the symbols used to translate the meanings of management practices is essential role for the organization. Objective: The objective of this study was to identify evidence of conceptual and empirical, on aspects of information architecture involved in the mapping process carried out in military organizations under the semiotic perspective. Methodology: The research is characterized as qualitative, case study and the data collection technique was the semi-structured interview, applied to management advisors. Results: The main results indicate that management practices described with the use of pictorial symbols and different layouts have greater impact to explain the relevance of management practices and indicators. Conclusion: With regard to the semiotic appeal, it was found that the impact of a management report is significant due to the use of signs and layout that stimulate further reading by simplifying complex concepts in tables, diagrams summarizing lengthy descriptions.

  1. Morphology Development in Solution-Processed Functional Organic Blend Films: An In Situ Viewpoint.

    Science.gov (United States)

    Richter, Lee J; DeLongchamp, Dean M; Amassian, Aram

    2017-05-10

    Solution-processed organic films are a facile route to high-speed, low cost, large-area deposition of electrically functional components (transistors, solar cells, emitters, etc.) that can enable a diversity of emerging technologies, from Industry 4.0, to the Internet of things, to point-of-use heath care and elder care. The extreme sensitivity of the functional performance of organic films to structure and the general nonequilibrium nature of solution drying result in extreme processing-performance correlations. In this Review, we highlight insights into the fundamentals of solution-based film deposition afforded by recent state-of-the-art in situ measurements of functional film drying. Emphasis is placed on multimodal studies that combine surface-sensitive X-ray scattering (GIWAXS or GISAXS) with optical characterization to clearly define the evolution of solute structure (aggregation, crystallinity, and morphology) with film thickness.

  2. Morphology Development in Solution-Processed Functional Organic Blend Films: An In Situ Viewpoint

    KAUST Repository

    Richter, Lee J.

    2017-04-17

    Solution-processed organic films are a facile route to high-speed, low cost, large-area deposition of electrically functional components (transistors, solar cells, emitters, etc.) that can enable a diversity of emerging technologies, from Industry 4.0, to the Internet of things, to point-of-use heath care and elder care. The extreme sensitivity of the functional performance of organic films to structure and the general nonequilibrium nature of solution drying result in extreme processing-performance correlations. In this Review, we highlight insights into the fundamentals of solution-based film deposition afforded by recent state-of-the-art in situ measurements of functional film drying. Emphasis is placed on multimodal studies that combine surface-sensitive X-ray scattering (GIWAXS or GISAXS) with optical characterization to clearly define the evolution of solute structure (aggregation, crystallinity, and morphology) with film thickness.

  3. A Marketing approach on how continuous processes improvement can contribute to hotel business Organic Growth

    Directory of Open Access Journals (Sweden)

    Ioana-Simona IVASCIUC

    2015-12-01

    Full Text Available Generating sustainable growth and profits is like finding a unicorn for most managers. Organic growth should be considered as an alternative for long-term growth in the hotel business. Designing the service process to deliver what customers expect from the hotel offer is a crucial component of encounter marketing. Hotels need to embrace the changes and ensure that their internal processes are aligned not just to current trends, but also to the expected future changes. Keeping up with global changes and trends of any kind, evaluating their impact on your business, continuous improving of the services using PDCA cycle, Six Sigma or Lean principles, are the keys to long-term organic growth.

  4. Organization of the two-level memory in the image processing system on scanning measuring projectors

    International Nuclear Information System (INIS)

    Sychev, A.Yu.

    1977-01-01

    Discussed are the problems of improving the efficiency of the system for processing pictures taken in bubble chambers with the use of scanning measuring projectors. The system comprises 20 to 30 pro ectors linked with the ICL-1903A computer provided with a mainframe memory, 64 kilobytes in size. Because of the insufficient size of a mainframe memory, a part of the programs and data is located in a second-level memory, i.e. in an external memory. The analytical model described herein is used to analyze the effect of the memory organization on the characteristics of the system. It is shown that organization of pure procedures and introduction of the centralized control of the tWo-leVel memory result in substantial improvement of the efficiency of the picture processing system

  5. Self-organization processes and nanocluster formation in crystal lattices by low-energy ion irradiation

    International Nuclear Information System (INIS)

    Tereshko, I.; Abidzina, V.; Tereshko, A.; Glushchenko, V.; Elkin, I.

    2007-01-01

    The goal of this paper is to study self-organization processes that cause nanostructural evolution in nonlinear crystal media. The subjects of the investigation were nonlinear homogeneous and heterogeneous atom chains. The method of computer simulation was used to investigate the interaction between low-energy ions and crystal lattices. It was based on the conception of three-dimensional lattice as a nonlinear atom chain system. We showed that that in homogeneous atom chains critical energy needed for self-organization processes development is less than for nonlinear atom chain with already embedded clusters. The possibility of nanostructure formation was studied by a molecular dynamics method of nonlinear oscillations in atomic oscillator systems of crystal lattices after their low-energy ion irradiation. (authors)

  6. Organization of film data processing in the PPI-SA automated system

    International Nuclear Information System (INIS)

    Ovsov, Yu.V.; Perekatov, V.G.

    1984-01-01

    Organization of processing nuclear interaction images at PUOS - type standard devices using the PPI-SA automated system is considered. The system is made in the form of a complete module comprising two scanning measuring projectors and a scan-ning automatic device which operate in real time on line with the BESM-4-computer. The system comprises: subsystem for photographic film scanning, selection of events for measurements and preliminary encoding; subsystem for formation and generation of libraries with data required for monitoring the scanning automatic device; subsystem for precision measurements separate coordinates on photo images of nuclear particle tracks and ionization losses. The system software comprises monitoring programs for the projectors and scanning automatic device as well as test functional control programs and operating system. The programs are organized a modular concept. By changing the module set the system can be modified and adapted for image processing in different fields of science and technology

  7. A mechanistic understanding of processing additive-induced efficiency enhancement in bulk heterojunction organic solar cells

    KAUST Repository

    Schmidt, Kristin

    2013-10-31

    The addition of processing additives is a widely used approach to increase power conversion efficiencies for many organic solar cells. We present how additives change the polymer conformation in the casting solution leading to a more intermixed phase-segregated network structure of the active layer which in turn results in a 5-fold enhancement in efficiency. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Effects-Directed Analysis of Dissolved Organic Compounds in Oil Sands Process-Affected Water.

    Science.gov (United States)

    Morandi, Garrett D; Wiseman, Steve B; Pereira, Alberto; Mankidy, Rishikesh; Gault, Ian G M; Martin, Jonathan W; Giesy, John P

    2015-10-20

    Acute toxicity of oil sands process-affected water (OSPW) is caused by its complex mixture of bitumen-derived organics, but the specific chemical classes that are most toxic have not been demonstrated. Here, effects-directed analysis was used to determine the most acutely toxic chemical classes in OSPW collected from the world's first oil sands end-pit lake. Three sequential rounds of fractionation, chemical analysis (ultrahigh resolution mass spectrometry), and acute toxicity testing (96 h fathead minnow embryo lethality and 15 min Microtox bioassay) were conducted. Following primary fractionation, toxicity was primarily attributable to the neutral extractable fraction (F1-NE), containing 27% of original organics mass. In secondary fractionation, F1-NE was subfractionated by alkaline water washing, and toxicity was primarily isolated to the ionizable fraction (F2-NE2), containing 18.5% of the original organic mass. In the final round, chromatographic subfractionation of F2-NE2 resulted in two toxic fractions, with the most potent (F3-NE2a, 11% of original organic mass) containing predominantly naphthenic acids (O2(-)). The less-toxic fraction (F3-NE2b, 8% of original organic mass) contained predominantly nonacid species (O(+), O2(+), SO(+), NO(+)). Evidence supports naphthenic acids as among the most acutely toxic chemical classes in OSPW, but nonacidic species also contribute to acute toxicity of OSPW.

  9. Batch Fermentative Biohydrogen Production Process Using Immobilized Anaerobic Sludge from Organic Solid Waste

    Directory of Open Access Journals (Sweden)

    Patrick T. Sekoai

    2016-12-01

    Full Text Available This study examined the potential of organic solid waste for biohydrogen production using immobilized anaerobic sludge. Biohydrogen was produced under batch mode at process conditions of 7.9, 30.3 °C and 90 h for pH, temperature and fermentation time, respectively. A maximum biohydrogen fraction of 48.67%, which corresponded to a biohydrogen yield of 215.39 mL H2/g Total Volatile Solids (TVS, was achieved. Therefore, the utilization of immobilized cells could pave the way for a large-scale biohydrogen production process.

  10. Organic-inorganic hybrid membranes in separation processes: a 10-year review

    Directory of Open Access Journals (Sweden)

    V. C. Souza

    2013-12-01

    Full Text Available In relation to some inorganic membranes, polymeric membranes have relatively low separation performance. However, the processing flexibility and low cost of polymers still make them highly attractive for many industrial separation applications. Polymer-inorganic hybrid membranes constitute an emerging research field and have been recently developed to improve the separation properties of polymer membranes because they possess properties of both organic and inorganic membranes such as good hydrophilicity, selectivity, permeability, mechanical strength, and thermal and chemical stability. The structures and processing of polymer-inorganic nanocomposite hybrid membranes, as well as their use in the fields of ultrafiltration, nanofiltration, pervaporation, gas separation and separation mechanism are reviewed.

  11. A business process model as a starting point for tight cooperation among organizations

    Directory of Open Access Journals (Sweden)

    O. Mysliveček

    2006-01-01

    Full Text Available Outsourcing and other kinds of tight cooperation among organizations are more and more necessary for success on all markets (markets of high technology products are particularly influenced. Thus it is important for companies to be able to effectively set up all kinds of cooperation. A business process model (BPM is a suitable starting point for this future cooperation. In this paper the process of setting up such cooperation is outlined, as well as why it is important for business success. 

  12. Time and temperature reduction of the sealing process of porous aluminium oxide films with organic additives

    International Nuclear Information System (INIS)

    Bautista, A.; Lopez, V.; Otero, E.; Lizarbe, R.; Gonzalez, J.A.

    1998-01-01

    Different sealing processes of anode coating in aluminium oxide have been industrially used for more than 30 years. In two of the preceding decades a great effort was realized to reduce costs in the traditional hydrothermal sealing in deionized boiling water (SHT), a very expensive process due to its endurance and high temperature on which it develops. New sealing procedures are proposed, on which by means of the use of organic additives, the time or the temperature of the SHT is essentially reduced. (Author) 10 refs

  13. Innovative process scheme for removal of organic matter, phosphorus and nitrogen from pig manure

    DEFF Research Database (Denmark)

    Karakashev, Dimitar Borisov; Schmidt, Jens Ejbye; Angelidaki, Irini

    2008-01-01

    blanket (UASB) reactor, partial oxidation), nitrogen (oxygen-limited autotrophic nitrification-denitrification, OLAND) and phosphorus (phosphorus removal by precipitation as struvite, PRS) from pig manure were tested. Results obtained showed that microfiltration was unsuitable for pig manure treatment....... PRS treated effluent was negatively affecting the further processing of the pig manure in UASB, and was therefore not included in the final process flow scheme. In a final scheme (PIGMAN concept) combination of the following successive process steps was used: thermophilic anaerobic digestion...... with sequential separation by decanter centrifuge, post-digestion in UASB reactor, partial oxidation and finally OLAND process. This combination resulted in reduction of the total organic, nitrogen and phosphorus contents by 96%, 88%, and 81%, respectively....

  14. Simulation of the organic-waste processing in plasma with allowance for kinetics of thermochemical transformations

    Science.gov (United States)

    Messerle, V. E.; Ustimenko, A. B.

    2017-07-01

    Kinetic calculations of the plasma processing/utilization process of organic waste in air and steam ambient were carried out. It is shown that, during the time of waste residence in the plasma reactor, 0.7 and 1.2 s, at the exit from the reactor there forms a high-calorific fuel gas with a combustion heat of 3540 and 5070 kcal/kg, respectively. In this process, 1 kg of waste yields 1.16 kg of fuel gas at air gasification of waste and 0.87 kg of pure synthesis gas at steam gasification. The energy efficiency of the waste gasification process, defined by the ratio between the calorific value of the resultant fuel gas and the initial calorific value of the waste amounts to 91 % in air plasma and 98 % in steam plasma. A comparison between the results of kinetic and thermodynamic calculations has revealed their good agreement.

  15. Unit Process Wetlands for Removal of Trace Organic Contaminants and Pathogens from Municipal Wastewater Effluents

    Science.gov (United States)

    Jasper, Justin T.; Nguyen, Mi T.; Jones, Zackary L.; Ismail, Niveen S.; Sedlak, David L.; Sharp, Jonathan O.; Luthy, Richard G.; Horne, Alex J.; Nelson, Kara L.

    2013-01-01

    Abstract Treatment wetlands have become an attractive option for the removal of nutrients from municipal wastewater effluents due to their low energy requirements and operational costs, as well as the ancillary benefits they provide, including creating aesthetically appealing spaces and wildlife habitats. Treatment wetlands also hold promise as a means of removing other wastewater-derived contaminants, such as trace organic contaminants and pathogens. However, concerns about variations in treatment efficacy of these pollutants, coupled with an incomplete mechanistic understanding of their removal in wetlands, hinder the widespread adoption of constructed wetlands for these two classes of contaminants. A better understanding is needed so that wetlands as a unit process can be designed for their removal, with individual wetland cells optimized for the removal of specific contaminants, and connected in series or integrated with other engineered or natural treatment processes. In this article, removal mechanisms of trace organic contaminants and pathogens are reviewed, including sorption and sedimentation, biotransformation and predation, photolysis and photoinactivation, and remaining knowledge gaps are identified. In addition, suggestions are provided for how these treatment mechanisms can be enhanced in commonly employed unit process wetland cells or how they might be harnessed in novel unit process cells. It is hoped that application of the unit process concept to a wider range of contaminants will lead to more widespread application of wetland treatment trains as components of urban water infrastructure in the United States and around the globe. PMID:23983451

  16. Unit Process Wetlands for Removal of Trace Organic Contaminants and Pathogens from Municipal Wastewater Effluents.

    Science.gov (United States)

    Jasper, Justin T; Nguyen, Mi T; Jones, Zackary L; Ismail, Niveen S; Sedlak, David L; Sharp, Jonathan O; Luthy, Richard G; Horne, Alex J; Nelson, Kara L

    2013-08-01

    Treatment wetlands have become an attractive option for the removal of nutrients from municipal wastewater effluents due to their low energy requirements and operational costs, as well as the ancillary benefits they provide, including creating aesthetically appealing spaces and wildlife habitats. Treatment wetlands also hold promise as a means of removing other wastewater-derived contaminants, such as trace organic contaminants and pathogens. However, concerns about variations in treatment efficacy of these pollutants, coupled with an incomplete mechanistic understanding of their removal in wetlands, hinder the widespread adoption of constructed wetlands for these two classes of contaminants. A better understanding is needed so that wetlands as a unit process can be designed for their removal, with individual wetland cells optimized for the removal of specific contaminants, and connected in series or integrated with other engineered or natural treatment processes. In this article, removal mechanisms of trace organic contaminants and pathogens are reviewed, including sorption and sedimentation, biotransformation and predation, photolysis and photoinactivation, and remaining knowledge gaps are identified. In addition, suggestions are provided for how these treatment mechanisms can be enhanced in commonly employed unit process wetland cells or how they might be harnessed in novel unit process cells. It is hoped that application of the unit process concept to a wider range of contaminants will lead to more widespread application of wetland treatment trains as components of urban water infrastructure in the United States and around the globe.

  17. Strategic Review Process for an Accountable Care Organization and Emerging Accountable Care Best Practices.

    Science.gov (United States)

    Conway, Sarah J; Himmelrich, Sarah; Feeser, Scott A; Flynn, John A; Kravet, Steven J; Bailey, Jennifer; Hebert, Lindsay C; Donovan, Susan H; Kachur, Sarah G; Brown, Patricia M C; Baumgartner, William A; Berkowitz, Scott A

    2018-02-02

    Accountable Care Organizations (ACOs), like other care entities, must be strategic about which initiatives they support in the quest for higher value. This article reviews the current strategic planning process for the Johns Hopkins Medicine Alliance for Patients (JMAP), a Medicare Shared Savings Program Track 1 ACO. It reviews the 3 focus areas for the 2017 strategic review process - (1) optimizing care coordination for complex, at-risk patients, (2) post-acute care, and (3) specialty care integration - reviewing cost savings and quality improvement opportunities, associated best practices from the literature, and opportunities to leverage and advance existing ACO and health system efforts in each area. It then reviews the ultimate selection of priorities for the coming year and early thoughts on implementation. After the robust review process, key stakeholders voted to select interventions targeted at care coordination, post-acute care, and specialty integration including Part B drug and imaging costs. The interventions selected incorporate a mixture of enhancing current ACO initiatives, working collaboratively and synergistically on other health system initiatives, and taking on new projects deemed targeted, cost-effective, and manageable in scope. The annual strategic review has been an essential and iterative process based on performance data and informed by the collective experience of other organizations. The process allows for an evidence-based strategic plan for the ACO in pursuit of the best care for patients.

  18. Delocalized organic pollutant destruction through a self-sustaining supercritical water oxidation process

    International Nuclear Information System (INIS)

    Lavric, E.D.; Weyten, H.; Ruyck, J. de; Plesu, V.; Lavric, V.

    2005-01-01

    Supercritical water oxidation (SCWO) is a recent development aiming at the destruction of organic pollutants present with low concentrations in waste waters. The present paper focuses on the process simulation of SCWO with emphasis on the proper modelling of supercritical thermodynamic conditions and on the possibility to make the SCWO process self-sufficient from the energetic viewpoint. Self-sufficiency may be of interest to encourage more delocalization of waste water treatment. The process of SCWO for dilute waste water (no more than 5 wt.%) is modelled through the ASPEN Plus copyright process simulator. Studies were made to search for energetic self-sufficiency conditions using various technologies for power production from the heat of reaction, like supercritical water expansion in a turbine, use of a closed Brayton cycle (CBC) and use of an organic Rankine cycle (ORC). The results obtained showed that the process is energetically self-sufficient using either a small supercritical turbine, or an ORC. In less restrictive conditions regarding the component efficiencies, the CBC, in theory, also leads to self-sufficiency, but from the analysis, it appears that this solution is less realistic

  19. Improved performance of organic solar cells with solution processed hole transport layer

    Science.gov (United States)

    Bhargav, Ranoo; Gairola, S. P.; Patra, Asit; Naqvi, Samya; Dhawan, S. K.

    2018-06-01

    This work is based on Cobalt Oxide as solution processed, inexpensive and effective hole transport layer (HTL) for efficient organic photovoltaic applications (OPVs). In Organic solar cell (OSC) devices ITO coated glass substrate used as a transparent anode electrode for light incident, HTL material Co3O4 dissolve in DMF solvent deposited on anode electrode, after that active layer material (donor/acceptor) deposited on to HTL and finally Al were deposited by thermal evaporation used as cathode electrode. These devices were fabricated with PCDTBT well known low band gap donor material in OSCs and blended with PC71BM as an acceptor material using simplest device structure ITO/Co3O4/active layer/Al at ambient conditions. The power conversion efficiencies (PCEs) based on Co3O4 and PEDOT:PSS have been achieved to up to 3.21% and 1.47% with PCDTBT respectively. In this study we reported that the devices fabricated with Co3O4 showed better performance as compare to the devices fabricated with well known and most studied solution processed HTL material PEDOT:PSS under identical environmental conditions. The surface morphology of the HTL film was characterized by (AFM). Lastly, we have provided Co3O4 as an efficient hole transport material HTL for solution processed organic photovoltaic applications.

  20. The shear flow processing of controlled DNA tethering and stretching for organic molecular electronics.

    Science.gov (United States)

    Yu, Guihua; Kushwaha, Amit; Lee, Jungkyu K; Shaqfeh, Eric S G; Bao, Zhenan

    2011-01-25

    DNA has been recently explored as a powerful tool for developing molecular scaffolds for making reproducible and reliable metal contacts to single organic semiconducting molecules. A critical step in the process of exploiting DNA-organic molecule-DNA (DOD) array structures is the controlled tethering and stretching of DNA molecules. Here we report the development of reproducible surface chemistry for tethering DNA molecules at tunable density and demonstrate shear flow processing as a rationally controlled approach for stretching/aligning DNA molecules of various lengths. Through enzymatic cleavage of λ-phage DNA to yield a series of DNA chains of various lengths from 17.3 μm down to 4.2 μm, we have investigated the flow/extension behavior of these tethered DNA molecules under different flow strengths in the flow-gradient plane. We compared Brownian dynamic simulations for the flow dynamics of tethered λ-DNA in shear, and found our flow-gradient plane experimental results matched well with our bead-spring simulations. The shear flow processing demonstrated in our studies represents a controllable approach for tethering and stretching DNA molecules of various lengths. Together with further metallization of DNA chains within DOD structures, this bottom-up approach can potentially enable efficient and reliable fabrication of large-scale nanoelectronic devices based on single organic molecules, therefore opening opportunities in both fundamental understanding of charge transport at the single molecular level and many exciting applications for ever-shrinking molecular circuits.

  1. THE USE OF BIOFILTRATION PROCESS TO REMOVE ORGANIC MATTER FROM GROUNDWATER

    Directory of Open Access Journals (Sweden)

    Dorota Papciak

    2016-07-01

    Full Text Available The article describes the research on the removal of organic matter from natural underground water using biofiltration process. The study was carried out in semi-technical scale on a model filter composed of activated carbon WD-extra. The development of biological activity in a biosorption bed, as well as observations on the relationship between the processes of sorption and biodegradation was evaluated based on the Eberhardt, Madsen, Sontheimer (EMS test. Leading operation control parameters of biologically active carbon filter BAF included: change of TOC content, dissolved oxygen and permanganate index. To evaluate the colonization of granular carbon determination of ATP value was used. The presence of the biofilm was found by observation using light and scanning microscopes. The organic compounds in the water taken were adsorbed 100% and 70% biodegradable. The combination of sorption process with biodegradation until depletion of activated carbon adsorption capacity allowed in the initial phase of coalbed work for the removal of organic matter in approx. 100% . Formation of biofilm at the right time allowed to extend the filtration cycle and helped lower the TOC by 70%, i.e. from 10 mg C/l to 3-4 mg C/l.

  2. Setting priorities in health care organizations: criteria, processes, and parameters of success

    Directory of Open Access Journals (Sweden)

    Martin Douglas K

    2004-09-01

    Full Text Available Abstract Background Hospitals and regional health authorities must set priorities in the face of resource constraints. Decision-makers seek practical ways to set priorities fairly in strategic planning, but find limited guidance from the literature. Very little has been reported from the perspective of Board members and senior managers about what criteria, processes and parameters of success they would use to set priorities fairly. Discussion We facilitated workshops for board members and senior leadership at three health care organizations to assist them in developing a strategy for fair priority setting. Workshop participants identified 8 priority setting criteria, 10 key priority setting process elements, and 6 parameters of success that they would use to set priorities in their organizations. Decision-makers in other organizations can draw lessons from these findings to enhance the fairness of their priority setting decision-making. Summary Lessons learned in three workshops fill an important gap in the literature about what criteria, processes, and parameters of success Board members and senior managers would use to set priorities fairly.

  3. Setting priorities in health care organizations: criteria, processes, and parameters of success.

    Science.gov (United States)

    Gibson, Jennifer L; Martin, Douglas K; Singer, Peter A

    2004-09-08

    Hospitals and regional health authorities must set priorities in the face of resource constraints. Decision-makers seek practical ways to set priorities fairly in strategic planning, but find limited guidance from the literature. Very little has been reported from the perspective of Board members and senior managers about what criteria, processes and parameters of success they would use to set priorities fairly. We facilitated workshops for board members and senior leadership at three health care organizations to assist them in developing a strategy for fair priority setting. Workshop participants identified 8 priority setting criteria, 10 key priority setting process elements, and 6 parameters of success that they would use to set priorities in their organizations. Decision-makers in other organizations can draw lessons from these findings to enhance the fairness of their priority setting decision-making. Lessons learned in three workshops fill an important gap in the literature about what criteria, processes, and parameters of success Board members and senior managers would use to set priorities fairly.

  4. Solution-Processed Molecular Organic Solar cell: Relationship between Morphology and Device Performance

    KAUST Repository

    Babics, Maxime

    2018-05-09

    In the last decade, organic photovoltaics (OPV) have gained considerable attention with a rapid improvement of power conversion efficiency (PCE) from 5% to more than 13%. At the origin of the gradual efficiency improvements are (i) the rationalization of material design and (ii) systematic optimization of film processing condition. OPV can have a key role in markets such as building-integrated photovoltaics (BIPV). The main advantages of organic solar cells are semitransparency, low weight, good performance at low light intensity, flexibility and potential low-cost module manufacture through solution processed-based technologies. In solution processed OPV, the active layer that converts photons into electric charges is a composite of two organic compounds, a donor (D) and an acceptor (A) where the best morphology is achieved via the so-called bulk heterojunction (BHJ): an interpenetrating phase-separated D-A network. Historically, research has been focused on polymer donors and guidelines about morphology and film processing have been established. However recent studies have shown that small-molecule (SM) donors can rival their polymer counterparts in performance. The advantages of SM are a defined molecular weight, the ease of purification and a good batch-to-batch reproducibility. Using this class of material the existing guidelines have to be adjusted and refined. In this dissertation, using new SM synthesized in our laboratory, solution-processed organic solar cells are fabricated in which the morphology of the active layer is controlled by thermal annealing, the use of additive or solvent vapor annealing. In-depth analyses of the morphology are correlated to charge generation, recombination and extraction inferred from device physics. In the first part of the dissertation, using a small amount of 1,8-Diiodooctane additive that acts as a plasticizer, it is found that the D-A domains do not necessarily need to be pure and that mixed domains can also result in

  5. Dynamic spatial organization of the occipito-temporal word form area for second language processing.

    Science.gov (United States)

    Gao, Yue; Sun, Yafeng; Lu, Chunming; Ding, Guosheng; Guo, Taomei; Malins, Jeffrey G; Booth, James R; Peng, Danling; Liu, Li

    2017-08-01

    Despite the left occipito-temporal region having shown consistent activation in visual word form processing across numerous studies in different languages, the mechanisms by which word forms of second languages are processed in this region remain unclear. To examine this more closely, 16 Chinese-English and 14 English-Chinese late bilinguals were recruited to perform lexical decision tasks to visually presented words in both their native and second languages (L1 and L2) during functional magnetic resonance imaging scanning. Here we demonstrate that visual word form processing for L1 versus L2 engaged different spatial areas of the left occipito-temporal region. Namely, the spatial organization of the visual word form processing in the left occipito-temporal region is more medial and posterior for L2 than L1 processing in Chinese-English bilinguals, whereas activation is more lateral and anterior for L2 in English-Chinese bilinguals. In addition, for Chinese-English bilinguals, more lateral recruitment of the occipito-temporal region was correlated with higher L2 proficiency, suggesting higher L2 proficiency is associated with greater involvement of L1-preferred mechanisms. For English-Chinese bilinguals, higher L2 proficiency was correlated with more lateral and anterior activation of the occipito-temporal region, suggesting higher L2 proficiency is associated with greater involvement of L2-preferred mechanisms. Taken together, our results indicate that L1 and L2 recruit spatially different areas of the occipito-temporal region in visual word processing when the two scripts belong to different writing systems, and that the spatial organization of this region for L2 visual word processing is dynamically modulated by L2 proficiency. Specifically, proficiency in L2 in Chinese-English is associated with assimilation to the native language mechanisms, whereas L2 in English-Chinese is associated with accommodation to second language mechanisms. Copyright © 2017

  6. Hydrothermal processing of Hanford tank waste. Organic destruction technology development task annual report -- FY 1993

    International Nuclear Information System (INIS)

    Orth, R.J.; Schmidt, A.J.; Zacher, A.H.

    1993-09-01

    Low-temperature hydrothermal processing (HTP) is a thermal-chemical autogenous processing method that can be used to destroy organics and ferrocyanide in Hanford tank waste at temperatures from 250 C to 400 C. With HTP, organics react with oxidants, such as nitrite and nitrate, already present in the waste. Ferrocyanides and free cyanide will hydrolyze at similar temperatures and may also react with nitrates or other oxidants in the waste. No air or oxygen or additional chemicals need to be added to the autogenous HTP system. However, enhanced kinetics may be realized by air addition, and, if desired, chemical reductants can be added to the system to facilitate complete nitrate/nitrate destruction. Tank waste can be processed in a plug-flow, tubular reactor, or a continuous-stirred tank reactor system designed to accommodate the temperature, pressure, gas generation, and heat release associated with decomposition of the reactive species. The work described in this annual report was conducted in FY 1993 for the Organic Destruction Technology Development Task of Hanford's Tank Waste Remediation System (TWRS). This task is part of an overall program to develop organic destruction technologies originally funded by TWRS to meet tank safety and waste form disposal criteria and condition the feed for further pretreatment. During FY 1993 the project completed seven experimental test plans, a 30-hr pilot-scale continuous run, over 200 hr of continuous bench-scale HTP testing, and 20 batch HTP tests; two contracts were established with commercial vendors, and a commercial laboratory reactor was procured and installed in a glovebox for HTP testing with actual Hanford tank waste

  7. Organics.

    Science.gov (United States)

    Chian, Edward S. K.; DeWalle, Foppe B.

    1978-01-01

    Presents water analysis literature for 1978. This review is concerned with organics, and it covers: (1) detergents and surfactants; (2) aliphatic and aromatic hydrocarbons; (3) pesticides and chlorinated hydrocarbons; and (4) naturally occurring organics. A list of 208 references is also presented. (HM)

  8. Organizers.

    Science.gov (United States)

    Callison, Daniel

    2000-01-01

    Focuses on "organizers," tools or techniques that provide identification and classification along with possible relationships or connections among ideas, concepts, and issues. Discusses David Ausubel's research and ideas concerning advance organizers; the implications of Ausubel's theory to curriculum and teaching; "webbing," a…

  9. [Investigation of team processes that enhance team performance in business organization].

    Science.gov (United States)

    Nawata, Kengo; Yamaguchi, Hiroyuki; Hatano, Toru; Aoshima, Mika

    2015-02-01

    Many researchers have suggested team processes that enhance team performance. However, past team process models were based on crew team, whose all team members perform an indivisible temporary task. These models may be inapplicable business teams, whose individual members perform middle- and long-term tasks assigned to individual members. This study modified the teamwork model of Dickinson and McIntyre (1997) and aimed to demonstrate a whole team process that enhances the performance of business teams. We surveyed five companies (member N = 1,400, team N = 161) and investigated team-level-processes. Results showed that there were two sides of team processes: "communication" and "collaboration to achieve a goal." Team processes in which communication enhanced collaboration improved team performance with regard to all aspects of the quantitative objective index (e.g., current income and number of sales), supervisor rating, and self-rating measurements. On the basis of these results, we discuss the entire process by which teamwork enhances team performance in business organizations.

  10. Storage effects on anthocyanins, phenolics and antioxidant activity of thermally processed conventional and organic blueberries.

    Science.gov (United States)

    Syamaladevi, Roopesh M; Andrews, Preston K; Davies, Neal M; Walters, Thomas; Sablani, Shyam S

    2012-03-15

    Consumer demand for products rich in phytochemicals is increasing as a result of greater awareness of their potential health benefits. However, processed products are stored for long-term and the phytochemicals are susceptible to degradation during storage. The objective of this study was to assess the storage effects on phytochemicals in thermally processed blueberries. Thermally processed canned berries and juice/puree were analysed for phytochemicals during their long-term storage. The phytochemical retention of thermally processed blueberries during storage was not influenced by production system (conventional versus organic). During 13 months of storage, total anthocyanins, total phenolics and total antioxidant activity in canned blueberry solids decreased by up to 86, 69 and 52% respectively. In canned blueberry syrup, total anthocyanins and total antioxidant activity decreased by up to 68 and 15% respectively, while total phenolic content increased by up to 117%. Similar trends in phytochemical content were observed in juice/puree stored for 4 months. The extent of changes in phytochemicals of thermally processed blueberries during storage was significantly influenced by blanching. Long-term storage of thermally processed blueberries had varying degrees of influence on degradation of total anthocyanins, total phenolics and total antioxidant activity. Blanching before thermal processing helped to preserve the phytochemicals during storage of blueberries. Copyright © 2011 Society of Chemical Industry.

  11. Studies on Manfred Eigen's model for the self-organization of information processing.

    Science.gov (United States)

    Ebeling, W; Feistel, R

    2018-05-01

    In 1971, Manfred Eigen extended the principles of Darwinian evolution to chemical processes, from catalytic networks to the emergence of information processing at the molecular level, leading to the emergence of life. In this paper, we investigate some very general characteristics of this scenario, such as the valuation process of phenotypic traits in a high-dimensional fitness landscape, the effect of spatial compartmentation on the valuation, and the self-organized transition from structural to symbolic genetic information of replicating chain molecules. In the first part, we perform an analysis of typical dynamical properties of continuous dynamical models of evolutionary processes. In particular, we study the mapping of genotype to continuous phenotype spaces following the ideas of Wright and Conrad. We investigate typical features of a Schrödinger-like dynamics, the consequences of the high dimensionality, the leading role of saddle points, and Conrad's extra-dimensional bypass. In the last part, we discuss in brief the valuation of compartment models and the self-organized emergence of molecular symbols at the beginning of life.

  12. Study of the degradation of organic molecules complexing radionuclides by using Advanced Oxidation Processes

    International Nuclear Information System (INIS)

    Rekab, K.

    2014-01-01

    This research thesis reports the study of the application of two AOPs (Advanced Oxidation Processes) to degrade and mineralise organic molecules which are complexing radio-elements, and thus to allow their concentrations by trapping on mineral matrices. EDTA (ethylene diamine tetraacetic acid) is chosen as reference organic complexing agent for preliminary tests performed with inactive cobalt 59 before addressing actual nuclear effluents with active cobalt 60. The author first presents the industrial context (existing nuclear wastes, notably liquid effluents and their processing) and proposes an overview of the state of the art on adsorption and precipitation of cobalt (natural and radioactive isotope). Then, the author presents the characteristics of the various studied oxides, the photochemical reactor used to perform tests, experimental techniques and operational modes. Results are then presented regarding various issues: adsorption of EDTA and the Co-EDTA complex, and cobalt precipitation; determination of the lamp photon flow by chemical actinometry and by using the Keitz method; efficiency of different processes (UV, UV/TiO 2 , UV/H 2 O 2 ) to degrade EDTA and to degrade the Co-EDTA complex; processing of a nuclear effluent coming from La Hague pools with determination of decontamination factors

  13. Characterization of natural organic matter treated by iron oxide nanoparticle incorporated ceramic membrane-ozonation process.

    Science.gov (United States)

    Park, Hosik; Kim, Yohan; An, Byungryul; Choi, Heechul

    2012-11-15

    In this study, changes in the physical and structural properties of natural organic matter (NOM) were observed during hybrid ceramic membrane processes that combined ozonation with ultrafiltration ceramic membrane (CM) or with a reactive ceramic membrane (RM), namely, an iron oxide nanoparticles (IONs) incorporated-CM. NOM from feed water and NOM from permeate treated with hybrid ceramic membrane processes were analyzed by employing several NOM characterization techniques. Specific ultraviolet absorbance (SUVA), high-performance size exclusion chromatography (HPSEC) and fractionation analyses showed that the hybrid ceramic membrane process effectively removed and transformed relatively high contents of aromatic, high molecular weight and hydrophobic NOM fractions. Fourier transform infrared spectroscopy (FTIR) and 3-dimensional excitation-emission matrix (EEM) fluorescence spectroscopy revealed that this process caused a significant decrease of the aromaticity of humic-like structures and an increase in electron withdrawing groups. The highest removal efficiency (46%) of hydroxyl radical probe compound (i.e., para-Chlorobenzoic acid (pCBA)) in RM-ozonation process compared with that in CM without ozonation process (8%) revealed the hydroxyl radical formation by the surface-catalyzed reaction between ozone and IONs on the surface of RM. In addition, experimental results on flux decline showed that fouling of RM-ozonation process (15%) was reduced compared with that of CM without ozonation process (30%). These results indicated that the RM-ozonation process enhanced the destruction of NOM and reduced the fouling by generating hydroxyl radicals from the catalytic ozonation in the RM-ozonation process. Copyright © 2012 Elsevier Ltd. All rights reserved.

  14. Solution-Processing of Organic Solar Cells: From In Situ Investigation to Scalable Manufacturing

    KAUST Repository

    Abdelsamie, Maged

    2016-12-05

    Photovoltaics provide a feasible route to fulfilling the substantial increase in demand for energy worldwide. Solution processable organic photovoltaics (OPVs) have attracted attention in the last decade because of the promise of low-cost manufacturing of sufficiently efficient devices at high throughput on large-area rigid or flexible substrates with potentially low energy and carbon footprints. In OPVs, the photoactive layer is made of a bulk heterojunction (BHJ) layer and is typically composed of a blend of an electron-donating (D) and an electron-accepting (A) materials which phase separate at the nanoscale and form a heterojunction at the D-A interface that plays a crucial role in the generation of charges. Despite the tremendous progress that has been made in increasing the efficiency of organic photovoltaics over the last few years, with power conversion efficiency increasing from 8% to 13% over the duration of this PhD dissertation, there have been numerous debates on the mechanisms of formation of the crucial BHJ layer and few clues about how to successfully transfer these lessons to scalable processes. This stems in large part from a lack of understanding of how BHJ layers form from solution. This lack of understanding makes it challenging to design BHJs and to control their formation in laboratory-based processes, such as spin-coating, let alone their successful transfer to scalable processes required for the manufacturing of organic solar cells. Consequently, the OPV community has in recent years sought out to better understand the key characteristics of state of the art lab-based organic solar cells and made efforts to shed light on how the BHJ forms in laboratory-based processes as well as in scalable processes. We take the view that understanding the formation of the solution-processed bulk heterojunction (BHJ) photoactive layer, where crucial photovoltaic processes take place, is the one of the most crucial steps to developing strategies towards the

  15. Figure-ground organization and object recognition processes: an interactive account.

    Science.gov (United States)

    Vecera, S P; O'Reilly, R C

    1998-04-01

    Traditional bottom-up models of visual processing assume that figure-ground organization precedes object recognition. This assumption seems logically necessary: How can object recognition occur before a region is labeled as figure? However, some behavioral studies find that familiar regions are more likely to be labeled figure than less familiar regions, a problematic finding for bottom-up models. An interactive account is proposed in which figure-ground processes receive top-down input from object representations in a hierarchical system. A graded, interactive computational model is presented that accounts for behavioral results in which familiarity effects are found. The interactive model offers an alternative conception of visual processing to bottom-up models.

  16. Process for preparing organoclays for aqueous and polar-organic systems

    Science.gov (United States)

    Chaiko, David J.

    2001-01-01

    A process for preparing organoclays as thixotropic agents to control the rheology of water-based paints and other aqueous and polar-organic systems. The process relates to treating low-grade clay ores to achieve highly purified organoclays and/or to incorporate surface modifying agents onto the clay by adsorption and/or to produce highly dispersed organoclays without excessive grinding or high shear dispersion. The process involves the treatment of impure, or run-of-mine, clay using an aqueous biphasic extraction system to produce a highly dispersed clay, free of mineral impurities and with modified surface properties brought about by adsorption of the water-soluble polymers used in generating the aqueous biphasic extraction system. This invention purifies the clay to greater than 95%.

  17. Strategy, Corporate Culture, Structure and Operational Processes as the Context for the Innovativeness of an Organization

    Directory of Open Access Journals (Sweden)

    Szczepańska-Woszczyna Katarzyna

    2018-03-01

    Full Text Available The paper refers to relationships between the innovativeness of an organization and its selected determinants such as strategy, corporate culture, structure and operational processes. Research was conducted among 200 managers at the top, middle and operational levels of management (200 companies operating in Poland implementing innovations - innovative companies. Conditions leading to innovations are described as the combination of processes, which result from the internal and external dynamics of a given entity. The analysis assumed that the assessment of company innovativeness would be based on an assessment of whether the company is a leader in the industry in terms of new products (the higher the rating, the more innovative the company is considered to be. The relationship between the dimensions of the company's functioning and the degree of its innovativeness was rated on the basis of two measures: the Spearman's rank correlation coefficient and the chi-square coefficient. It was assumed that the most innovative companies have structures similar to organic ones, with a weak influence of the elements of mechanistic structures. This assumption was proven in relation to features of organizations considered important for innovativeness.

  18. Low temperature hydrothermal processing of organic contaminants in Hanford tank waste

    International Nuclear Information System (INIS)

    Jones, E.O.; Pederson, L.R.; Freeman, H.D.; Schmidt, A.J.; Babad, H.

    1993-02-01

    Batch and continuous flow reactor tests at Pacific Northwest Laboratory (PNL) have shown that organics similar to those present in the single-shell and double-shell underground storage tanks at Hanford can be decomposed in the liquid phase at relatively mild temperatures of 150 degree C to 350 degree C in an aqueous process known as hydrothermal processing (HTP). The organics will react with the abundant oxidants such s nitrite already present in the Hanford tank waste to form hydrogen, carbon dioxide, methane, and ammonia. No air or oxygen needs to be added to the system. Ferrocyanides and free cyanide will hydrolyze at similar temperatures to produce formate and ammonia and may also react with nitrates or other oxides. During testing, the organic carbon was transformed first to oxalate at∼310 degree C and completely oxidized to carbonate at ∼350 degree C accompanied by hydroxide consumption. Solids were formed at higher temperatures, causing a small-diameter outlet tube to plug. The propensity for plugging was reduced by diluting the feed with concentrated hydroxide

  19. Process for the restoration of solids contaminated with hydrocarbons and heavy organic compounds

    International Nuclear Information System (INIS)

    Bala, G.A.; Thomas, C.P.; Jackson, J.D.; McMillin, R.A.

    1994-01-01

    Processes have been developed for the restoration of environments contaminated with hydrocarbons and heavy organics. The intended product is a field deployable materials handling system and phase separation process ranging in size from 1 yd 3 /hr to 50 yd 3 /hr for commercial application to environmental problems associated with the exploration, production, refining and transport of petroleum, petroleum products and organic chemicals. Effluents from contaminated sites will be clean solids (classified by size if appropriate), and the concentrated contaminant. The technology is based on biochemical solvation, liquid/liquid and liquid/solid extractions, materials classification, mechanical and hydraulic scrubbing, and phase separation of organic and aqueous phases. Fluid use is minimized through utilization of closed-loop (recycle) systems. Contaminants that are removed from the solid materials may be destroyed, disposed of using existing technologies, or used on-site for cogeneration of /power for plant operations. Additionally, if the contaminant is a valued product, the material may be recovered for application or sale. Clean solid material is not sterilized and may be returned to normal agricultural, commercial, residential or recreational use in most instances

  20. Critical assessment of anaerobic processes for continuous biohydrogen production from organic wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Show, Kuan-Yeow [Faculty of Engineering and Green Technology, University Tunku Abdul Rahman, Jalan University, Bandar Barat, 31900 Kampar, Perak (Malaysia); Zhang, Zhen-Peng [Beijing Enterprises Water Group Limited, BLK 25, No. 3 Minzhuang Road, Beijing 100195 (China); Tay, Joo-Hwa [School of Civil and Environmental Engineering, Nanyang Technological University, Nanyang Avenue (Singapore); Liang, David Tee [Institute of Environmental Science and Engineering, Nanyang Technological University (Singapore); Lee, Duu-Jong [Department of Chemical Engineering, National Taiwan University, Taipei (China); Ren, Nanqi; Wang, Aijie [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090 (China)

    2010-12-15

    Production of biohydrogen using dark fermentation has received much attention owing to the fact that hydrogen can be generated from renewable organics including waste materials. The key to successful application of anaerobic fermentation is to uncouple the liquid retention time and the biomass retention time in the reactor system. Various reactor designs based on biomass retention within the reactor system have been developed. This paper presents our research work on bioreactor designs and operation for biohydrogen production. Comparisons between immobilized-cell systems and suspended-cell systems based on biomass growth in the forms of granule, biofilm and flocs were made. Reactor configurations including column- and tank-based reactors were also assessed. Experimental results indicated that formation of granules or biofilms substantially enhanced biomass retention which was found to be proportional to the hydrogen production rate. Rapid hydrogen-producing culture growth and high organic loading rate might limit the application of biofilm biohydrogen production, since excessive growth of fermentative biomass would result in washout of support carrier. It follows that column-based granular sludge process is a preferred choice of process for continuous biohydrogen production from organic wastewater, indicating maximum hydrogen yield of 1.7 mol-H{sub 2}/mol-glucose and hydrogen production rate of 6.8 L-H{sub 2}/L-reactor h. (author)

  1. [Pharmaceutical Assistance in the Family Healthcare Program: points of affinity and discord in the organization process].

    Science.gov (United States)

    Silva Oliveira, Tatiana de Alencar; Maria, Tatiane de Oliveira Silva; Alves do Nascimento, Angela Maria; do Nascimento, Angela Alves

    2011-09-01

    The scope of this study was to discuss the organization of the pharmaceutical assistance service in the family healthcare program. Qualitative research from a critical/analytical perspective was conducted in family healthcare units in a municipality of the state of Bahia, Brazil. Data was collected on the basis of systematic observation, semi-structured interviews and documents analysis from a dialectic standpoint. The organization of Pharmaceutical Assistance consisted of selection, planning, acquisition, storage and dispensing activities. The process was studied in the implementation phase, which was occurring in a centralized and uncoordinated fashion, without the proposed team work. An excess of activity was observed among the healthcare workers and there was an absence of a continued education policy for the workers. For the transformation of this situation and to ensure the organization of pharmaceutical assistance with quality and in an integrated manner, a reworking of the manner of thinking and action of the players concerned (managers, health workers and users), who participate directly in the organization, is necessary. Furthermore, mechanical, bureaucratic and impersonal work practices need to be abandoned.

  2. Solution processable inverted structure ZnO-organic hybrid heterojuction white LEDs

    Science.gov (United States)

    Bano, N.; Hussain, I.; Soomro, M. Y.; EL-Naggar, A. M.; Albassam, A. A.

    2018-05-01

    Improving luminance efficiency and colour purity are the most important challenges for zinc oxide (ZnO)-organic hybrid heterojunction light emitting diodes (LEDs), affecting their large area applications. If ZnO-organic hybrid heterojunction white LEDs are fabricated by a hydrothermal method, it is difficult to obtain pure and stable blue emission from PFO due to the presence of an undesirable green emission. In this paper, we present an inverted-structure ZnO-organic hybrid heterojunction LED to avoid green emission from PFO, which mainly originates during device processing. With this configuration, each ZnO nanorod (NR) forms a discrete p-n junction; therefore, large-area white LEDs can be designed without compromising the junction area. The configuration used for this novel structure is glass/ZnO NRs/PFO/PEDOT:PSS/L-ITO, which enables the development of efficient, large-area and low-cost hybrid heterojunction LEDs. Inverted-structure ZnO-organic hybrid heterojunction white LEDs offer several improvements in terms of brightness, size, colour, external quantum efficiency and a wider applicability as compared to normal architecture LEDs.

  3. Decomposition of organic pollutants in industrial Effluent induced by advanced oxidation process with Electron beam irradiation

    International Nuclear Information System (INIS)

    Duarte, C.L.; Sampa, M.H.O.; Rela, P.R.; Oikawa, H.; Silveira, C.G.

    2001-01-01

    Advanced Oxidation Process (AOP) by electron beam irradiation induce the decomposition of pollutants in industrial effluent. Experiments were conducted using a Radiation Dynamics Electron Beam Accelerator with 1.5 MeV energy and 37 Kew power. Experiments were conducted using samples from a Governmental Wastewater Treatment Plant (WTP) that receives about 20% of industrial wastewater, with the objective of use the electrons beam technology to destroy the refractory organic pollutants. Samples from WTP main Industrial Receiver Unit influent (IRU), Coarse Bar Screens effluent (CBS), Medium Bar Screens effluent (MBS), Primary Sedimentation effluent (PS) and Final Effluent (FE), were collected and irradiated in the electron beam accelerator in a batch system. The delivered doses were 5.0kGy, 10.0kGy and 20.0kGy. The electron beam irradiation showed be efficient on destroying the organic compounds delivered in these effluents mainly chloroform, dichloroethane, methyl isobutyl ketone, benzene, toluene, xylene, phenol. The necessary dose to remove 90% of the most organic compounds from industry effluent was 20 kGy. The removal of organic compounds from this complex mixture were described by the destruction G value (Gd) that were obtained for those compounds in different initial concentration and compared with literature

  4. Effect of influent aeration on removal of organic matter from coffee processing wastewater in constructed wetlands.

    Science.gov (United States)

    Rossmann, Maike; Matos, Antonio Teixeira; Abreu, Edgar Carneiro; Silva, Fabyano Fonseca; Borges, Alisson Carraro

    2013-10-15

    The aim of the present study was to evaluate the influence of aeration and vegetation on the removal of organic matter in coffee processing wastewater (CPW) treated in 4 constructed wetlands (CWs), characterized as follows: (i) ryegrass (Lolium multiflorum) cultivated system operating with an aerated influent; (ii) non-cultivated system operating with an aerated influent, (iii) ryegrass cultivated system operating with a non-aerated influent; and (iv) non-cultivated system operating with a non-aerated influent. The lowest average chemical oxygen demand (COD), biochemical oxygen demand (BOD) and total suspended solids (TSS) removal efficiencies of 87, 84 and 73%, respectively, were obtained in the ryegrass cultivated system operating with a non-aerated influent. However, ryegrass cultivation did not influence the removal efficiency of organic matter. Artificial aeration of the CPW, prior to its injection in the CW, did not improve the removal efficiencies of organic matter. On other hand it did contribute to increase the instantaneous rate at which the maximum COD removal efficiency was reached. Although aeration did not result in greater organic matter removal efficiencies, it is important to consider the benefits of aeration on the removal of the other compounds. Copyright © 2013 Elsevier Ltd. All rights reserved.

  5. The Managerial Reduction in the Management Technologies Transposition Process to Public Organizations

    Directory of Open Access Journals (Sweden)

    Sandro Trescastro Bergue

    2010-04-01

    Full Text Available This essay discusses the phenomenon of the implementation of technologies designed in the management business, with emphasis on relations with public organizations. It proposes a reflection on the concept of sociological reduction by Guerreiro Ramos, recovering its roots in Husserl and Heidegger and their relationship with the concepts of creative adaptation and the translation of managerial issues. Contextualized in the paradigm of new public management and the list of values and assumptions on which this movement is based, the analysis of the reproduction of practices known in private organizations by public ones seeking their legitimacy has revealed the formality and ceremonial aspect of this contemporary phenomenon. The importance of bringing knowledge from the organizational field that subsidizes management as well as the coherence of these cultural objects in terms of concepts and assumptions of organization are highlighted here. The process of transpositions, contrasting with reproducible traits of Brazilian managerial culture that are historically constructed but consistent with the notion of sociological reduction, requires a critical, conscious and engaged attitude on the part of members of the organization not only regarding the relevance of the imported content but also giving new meaning to the concepts underlying the management technologies.

  6. Organic solar cells with graded absorber layers processed from nanoparticle dispersions.

    Science.gov (United States)

    Gärtner, Stefan; Reich, Stefan; Bruns, Michael; Czolk, Jens; Colsmann, Alexander

    2016-03-28

    The fabrication of organic solar cells with advanced multi-layer architectures from solution is often limited by the choice of solvents since most organic semiconductors dissolve in the same aromatic agents. In this work, we investigate multi-pass deposition of organic semiconductors from eco-friendly ethanol dispersion. Once applied, the nanoparticles are insoluble in the deposition agent, allowing for the application of further nanoparticulate layers and hence for building poly(3-hexylthiophene-2,5-diyl):indene-C60 bisadduct absorber layers with vertically graded polymer and conversely graded fullerene concentration. Upon thermal annealing, we observe some degrees of polymer/fullerene interdiffusion by means of X-ray photoelectron spectroscopy and Kelvin probe force microscopy. Replacing the common bulk-heterojunction by such a graded photo-active layer yields an enhanced fill factor of the solar cell due to an improved charge carrier extraction, and consequently an overall power conversion efficiency beyond 4%. Wet processing of such advanced device architectures paves the way for a versatile, eco-friendly and industrially feasible future fabrication of organic solar cells with advanced multi-layer architectures.

  7. METHODS FOR ORGANIZATION OF WORKING PROCESS FOR GAS-DIESEL ENGINE

    Directory of Open Access Journals (Sweden)

    G. A. Vershina

    2017-01-01

    Full Text Available Over the past few decades reduction in pollutant emissions has become one of the main directions for further deve- lopment of engine technology. Solution of such problems has led to implementation of catalytic post-treatment systems, new technologies of fuel injection, technology for regulated phases of gas distribution, regulated turbocharger system and, lately, even system for variable compression ratio of engine. Usage of gaseous fuel, in particular gas-diesel process, may be one of the means to reduce air pollution caused by toxic substances and meet growing environmental standards and regulations. In this regard, an analysis of methods for organization of working process for a gas-diesel engine has been conducted in the paper. The paper describes parameters that influence on the nature of gas diesel process, it contains graphics of specific total heat consumption according to ignition portion of diesel fuel and dependence of gas-diesel indices on advance angle for igni-tion portion injection of the diesel fuel. A modern fuel system of gas-diesel engine ГД-243 has been demonstrated in the pa- per. The gas-diesel engine has better environmental characteristics than engines running on diesel fuel or gasoline. According to the European Natural & bio Gas Vehicle Association a significant reduction in emissions is reached at a 50%-substitution level of diesel fuel by gas fuel (methane and in such a case there is a tendency towards even significant emission decrease. In order to ensure widespread application of gaseous fuel as fuel for gas-diesel process it is necessary to develop a new wor- king process, to improve fuel equipment, to enhance injection strategy and fuel supply control. A method for organization of working process for multi-fuel engine has been proposed on the basis of the performed analysis. An application has been submitted for a patent.

  8. The study of features of the structural organization of the au-tomated information processing system of the collective type

    Science.gov (United States)

    Nikolaev, V. N.; Titov, D. V.; Syryamkin, V. I.

    2018-05-01

    The comparative assessment of the level of channel capacity of different variants of the structural organization of the automated information processing systems is made. The information processing time assessment model depending on the type of standard elements and their structural organization is developed.

  9. Flexible organic tandem solar modules with 6% efficiency: combining roll-to-roll compatible processing with high geometric fill factors

    DEFF Research Database (Denmark)

    Spyropoulos, G. D.; Kubis, P.; Li, Na

    2014-01-01

    Organic solar cell technology bears the potential for high photovoltaic performance combined with truly low-cost, high-volume processing. Here we demonstrate organic tandem solar modules on flexible substrates fabricated by fully roll-to-roll compatible processing at temperatures...

  10. A Conceptual Schema of the Programming Process in the Complex Adult Education Organization with Special Emphasis on Its Sociological Aspects.

    Science.gov (United States)

    Boone, Edgar J.; And Others

    Objectives of this paper were to define the concept of programing, to discuss programing in a complex adult education organization, and to point out aspects of programing of a sociological nature. Programing is a decision-making process. In a complex adult education organization, the process can be divided into eight phases: formulating the…

  11. X-ray imager using solution processed organic transistor arrays and bulk heterojunction photodiodes on thin, flexible plastic substrate

    NARCIS (Netherlands)

    Gelinck, G.H.; Kumar, A.; Moet, D.; Steen, J.L. van der; Shafique, U.; Malinowski, P.E.; Myny, K.; Rand, B.P.; Simon, M.; Rütten, W.; Douglas, A.; Jorritsma, J.; Heremans, P.L.; Andriessen, H.A.J.M.

    2013-01-01

    We describe the fabrication and characterization of large-area active-matrix X-ray/photodetector array of high quality using organic photodiodes and organic transistors. All layers with the exception of the electrodes are solution processed. Because it is processed on a very thin plastic substrate

  12. Modeling of Electrochemical Process for the Treatment of Wastewater Containing Organic Pollutants

    Science.gov (United States)

    Rodrigo, Manuel A.; Cañizares, Pablo; Lobato, Justo; Sáez, Cristina

    Electrocoagulation and electrooxidation are promising electrochemical technologies that can be used to remove organic pollutants contained in wastewaters. To make these technologies competitive with the conventional technologies that are in use today, a better understanding of the processes involved must be achieved. In this context, the development of mathematical models that are consistent with the processes occurring in a physical system is a relevant advance, because such models can help to understand what is happening in the treatment process. In turn, a more detailed knowledge of the physical system can be obtained, and tools for a proper design of the processes, or for the analysis of operating problems, are attained. The modeling of these technologies can be carried out using single-variable or multivariable models. Likewise, the position dependence of the model species can be described with different approaches. In this work, a review of the basics of the modeling of these processes and a description of several representative models for electrochemical oxidation and coagulation are carried out. Regarding electrooxidation, two models are described: one which summarizes the pollution of a wastewater in only one model species and that considers a macroscopic approach to formulate the mass balances and other that considers more detailed profile of concentration to describe the time course of pollutants and intermediates through a mixed maximum gradient/macroscopic approach. On the topic of electrochemical coagulation, two different approaches are also described in this work: one that considers the hydrodynamic conditions as the main factor responsible for the electrochemical coagulation processes and the other that considers the chemical interaction of the reagents and the pollutants as the more significant processes in the description of the electrochemical coagulation of organic compounds. In addition, in this work it is also described a multivariable model

  13. Determination of inorganic and organic priority pollutants in biosolids from meat processing industry

    International Nuclear Information System (INIS)

    Sena, Rennio F. de; Tambosi, Jose L.; Floriani, Silvia L.; Virmond, Elaine; Schroeder, Horst Fr.; Moreira, Regina F.P.M.; Jose, Humberto J.

    2009-01-01

    The biosolids (BS) generated in the wastewater treatment process of a meat processing plant were monitored and the priority pollutant content was characterized. The trace metal and organic pollutant content - polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/PCDF) - were determined quantitatively and compared to guideline limits established by the US EPA and EU. PCBs were not detected in the solid samples, while trace metals, PAHs and PCDD/PCDF were detected in concentrations below the limits established by international standards. Toxic equivalent factors were evaluated for the biosolids, and the results proved that these wastes can be safely deposited on land or used in combustion/incineration plants. Since no previous data were found for meat processing waste, comparisons were made using municipal sewage sludge data reported in the literature. Since, this report monitored part of the priority pollutants established by the US EPA for meat and poultry processing wastewater and sludge, the results verified that low pollution loads are generated by the meat processing plant located in the southern part of Brazil. However, the BS generated in the treatment processes are in accordance with the limits established for waste disposal and even for soil fertilizer.

  14. Model of the expansion process for R245fa in an Organic Rankine Cycle (ORC)

    International Nuclear Information System (INIS)

    Luján, J.M.; Serrano, J.R.; Dolz, V.; Sánchez, J.

    2012-01-01

    An Organic Rankine Cycle (ORC) is considered as one of the most environmental-friendly ways to convert different kinds of low temperature energies, i.e. solar, geothermal, biomass and thermal energy of exhaust gases into electrical energy. Two important facts about the ORC must be considered: An organic fluid is selected as the working fluid and a high expansion ratio is usually presented in the machinery due to thermodynamic and efficiency factors. In the past, the pre-design of turbomachinery has been based on the usage of ideal fluid laws, but the real gas effects have a significant influence in the ORC working condition, due to its proximity to the saturation vapor line. In this article, the Equations of State (EoS) (Ideal gas, Redlich-Kwong-Soave and Peng–Robinson) have been evaluated in a typical ORC expansion in order to observe the inaccuracies of the ideal gas model with different thermodynamic variables. Finally an isothermal process followed by an isochoric process is proposed to reproduce the thermodynamic process of the organic fluid expansion by means of simpler equations. In the last point of this paper, several examples of this expansion process have been calculated, in order to analyze the proposed methodologies. It has been concluded that in typical expansion process of ORC (2.5 MPa-0.1 MPa and 1.6MPa-0.1 MPa), the PR and RKS equations show deviations between 6% and 8% in specific energy. These deviations are very low compared with the ideal gas equation whose deviations are above 100%. - Highlights: ► Evaluate the ideal gas behaviour of R245fa in typical working conditions of an Organic Rankine Cycle (ORC). ► Compare the ideal behaviour with other simple equations of state for real gas. ► Decide which equation of state has the highest precision in typical working conditions of an ORC. ► Derive the most important thermodynamic variables in each equation of state and decide the most accurate equation. ► Evaluate the speci c output

  15. USAGE OF SOCIAL SERVICES IN THE PROCESS OF ORGANIZATION OF COMMUNICATION FOR FOREIGN LANGUAGE TEACHERS

    Directory of Open Access Journals (Sweden)

    Myloslava M. Chernii

    2013-10-01

    Full Text Available Today especially urgent problem is communication and the development of communication skills of future teachers as well as communicative culture is the main structural component of his professionalism. Schools and classes, both conventional and virtual, must have teachers, armed with technology resources and skills, and able to effectively teach the subject using information and communication technologies. It all comes down to the fact that the modern teacher has to be aware of the latest technologies that can help him to organize trainings and communication. Therefore, a special role is given to the training of future teachers and vector of application of social services in the organization of communication in the learning process.

  16. Patterning solution-processed organic single-crystal transistors with high device performance

    Directory of Open Access Journals (Sweden)

    Yun Li

    2011-06-01

    Full Text Available We report on the patterning of organic single-crystal transistors with high device performance fabricated via a solution process under ambient conditions. The semiconductor was patterned on substrates via surface selective deposition. Subsequently, solvent-vapor annealing was performed to reorganize the semiconductor into single crystals. The transistors exhibited field-effect mobility (μFET of up to 3.5 cm2/V s. Good reliability under bias-stress conditions indicates low density of intrinsic defects in crystals and low density of traps at the active interfaces. Furthermore, the Y function method clearly suggests that the variation of μFET of organic crystal transistors was caused by contact resistance. Further improvement of the device with higher μFET with smaller variation can be expected when lower and more uniform contact resistance is achieved.

  17. Evaluation of organic and inorganic compounds levels of red wines processed from Pinot Noir grapes

    Directory of Open Access Journals (Sweden)

    Heli Sirén

    2015-03-01

    The wine products showed different profiles of carbohydrates, organic acids, phenolic compounds, and minerals. Especially, saccharose (max. 0.21 g/L, rhamnose (max. 0.45 g/L, fructose (max. 1.9 g/L, and phosphate (max 1.4 g/L quantities were extremely high in some wines. The results also showed that yeast fermentation in winemaking agitated high production of lactic (max 5.7 g/L and tartaric (max 1.7 g/L acids. The red wines processed by cold maceration and natural fermentation gave similar profiles. Only one of the Pinot Noir wines entirely differentiated from the others with comparison of carbohydrates and organic acids.

  18. Solution-Processed Organic and Halide Perovskite Transistors on Hydrophobic Surfaces.

    Science.gov (United States)

    Ward, Jeremy W; Smith, Hannah L; Zeidell, Andrew; Diemer, Peter J; Baker, Stephen R; Lee, Hyunsu; Payne, Marcia M; Anthony, John E; Guthold, Martin; Jurchescu, Oana D

    2017-05-31

    Solution-processable electronic devices are highly desirable due to their low cost and compatibility with flexible substrates. However, they are often challenging to fabricate due to the hydrophobic nature of the surfaces of the constituent layers. Here, we use a protein solution to modify the surface properties and to improve the wettability of the fluoropolymer dielectric Cytop. The engineered hydrophilic surface is successfully incorporated in bottom-gate solution-deposited organic field-effect transistors (OFETs) and hybrid organic-inorganic trihalide perovskite field-effect transistors (HTP-FETs) fabricated on flexible substrates. Our analysis of the density of trapping states at the semiconductor-dielectric interface suggests that the increase in the trap density as a result of the chemical treatment is minimal. As a result, the devices exhibit good charge carrier mobilities, near-zero threshold voltages, and low electrical hysteresis.

  19. Effect of Processing Parameters on Performance of Spray-Deposited Organic Thin-Film Transistors

    Directory of Open Access Journals (Sweden)

    Jack W. Owen

    2011-01-01

    Full Text Available The performance of organic thin-film transistors (OTFTs is often strongly dependent on the fabrication procedure. In this study, we fabricate OTFTs of soluble small-molecule organic semiconductors by spray-deposition and explore the effect of processing parameters on film morphology and device mobility. In particular, we report on the effect of the nature of solvent, the pressure of the carrier gas used in deposition, and the spraying distance. We investigate the surface morphology using scanning force microscopy and show that the molecules pack along the π-stacking direction, which is the preferred charge transport direction. Our results demonstrate that we can tune the field-effect mobility of spray-deposited devices two orders of magnitude, from 10−3 cm2/Vs to 10−1 cm2/Vs, by controlling fabrication parameters.

  20. Effects of Organic Matter and Clay Content in Soil on Pesticide Adsorption Processes

    Directory of Open Access Journals (Sweden)

    Rada Đurović

    2009-01-01

    Full Text Available The effect of organic matter and clay content on the adsorption of atrazine, acetochlor, clomazone, pendimethalin and oxyfluorfen in soil samples was studied. In order to determine whether and to what degree different soil properties affect the process of determinationof selected pesticides, three soils with different clay and organic matter contents were used. An optimized liquid-solid extraction procedure followed by SPME measurement was applied to analyse the selected pesticides in soil samples. Detection and quantificationwere done by gas chromatography-mass spectrometry (GC/MS. Relative standard deviation (RSD values for multiple analyses of soil samples fortified at 30 μg/kg of each pesticide were below 19%. Limits of detection (LODs for all compounds studied were less than 2 μg/kg. The results indicate that soils with different physico-chemical properties have different effects on the adsorption of most pesticides, especially at higher concentration levels.

  1. Self-Organized Criticality in Astrophysics The Statistics of Nonlinear Processes in the Universe

    CERN Document Server

    Aschwanden, Markus

    2011-01-01

    The concept of ‘self-organized criticality’ (SOC) has been applied to a variety of problems, ranging from population growth and traffic jams to earthquakes, landslides and forest fires. The technique is now being applied to a wide range of phenomena in astrophysics, such as planetary magnetospheres, solar flares, cataclysmic variable stars, accretion disks, black holes and gamma-ray bursts, and also to phenomena in galactic physics and cosmology. Self-organized Criticality in Astrophysics introduces the concept of SOC and shows that, due to its universality and ubiquity, it is a law of nature. The theoretical framework and specific physical models are described, together with a range of applications in various aspects of astrophyics. The mathematical techniques, including the statistics of random processes, time series analysis, time scale and waiting time distributions, are presented and the results are applied to specific observations of astrophysical phenomena.

  2. Flexible Electronics: Integration Processes for Organic and Inorganic Semiconductor-Based Thin-Film Transistors

    Directory of Open Access Journals (Sweden)

    Fábio F. Vidor

    2015-07-01

    Full Text Available Flexible and transparent electronics have been studied intensively during the last few decades. The technique establishes the possibility of fabricating innovative products, from flexible displays to radio-frequency identification tags. Typically, large-area polymeric substrates such as polypropylene (PP or polyethylene terephthalate (PET are used, which produces new requirements for the integration processes. A key element for flexible and transparent electronics is the thin-film transistor (TFT, as it is responsible for the driving current in memory cells, digital circuits or organic light-emitting devices (OLEDs. In this paper, we discuss some fundamental concepts of TFT technology. Additionally, we present a comparison between the use of the semiconducting organic small-molecule pentacene and inorganic nanoparticle semiconductors in order to integrate TFTs suitable for flexible electronics. Moreover, a technique for integration with a submicron resolution suitable for glass and foil substrates is presented.

  3. Types of organic materials present in CEGB waste streams and possible encapsulation processes for organic ion-exchange materials

    International Nuclear Information System (INIS)

    Haighton, A.P.

    1988-01-01

    The organic composition of low and intermediate-level radioactive wastes is discussed. Work underway in the development of immobilising binders for organic ion exchange resins found in radioactive wastes and in the encapsulation of these ion exchangers is presented. (U.K.)

  4. Low-Temperature Solution-Processed Gate Dielectrics for High-Performance Organic Thin Film Transistors

    Directory of Open Access Journals (Sweden)

    Jaekyun Kim

    2015-10-01

    Full Text Available A low-temperature solution-processed high-k gate dielectric layer for use in a high-performance solution-processed semiconducting polymer organic thin-film transistor (OTFT was demonstrated. Photochemical activation of sol-gel-derived AlOx films under 150 °C permitted the formation of a dense film with low leakage and relatively high dielectric-permittivity characteristics, which are almost comparable to the results yielded by the conventionally used vacuum deposition and high temperature annealing method. Octadecylphosphonic acid (ODPA self-assembled monolayer (SAM treatment of the AlOx was employed in order to realize high-performance (>0.4 cm2/Vs saturation mobility and low-operation-voltage (<5 V diketopyrrolopyrrole (DPP-based OTFTs on an ultra-thin polyimide film (3-μm thick. Thus, low-temperature photochemically-annealed solution-processed AlOx film with SAM layer is an attractive candidate as a dielectric-layer for use in high-performance organic TFTs operated at low voltages.

  5. Using Coagulation Process in Optimizing Natural Organic Matter Removal from Low Turbidity Waters

    Directory of Open Access Journals (Sweden)

    Alireza Mesdaghinia

    2006-03-01

    Full Text Available Optimization of coagulation process  for efficient removal of Natural Organic Matters (NOM has gained a lot of focus over the last years to meet the requirements of enhanced coagulation. NOM comprises both particulate and soluble components which the latter usually comprises the main portion. Removal of soluble NOM from low turbidity waters by coagulation is not a successful process unless enough attention is paid to stages of formation and development of both micro and macro-flocs. This study, which presents experimental results from pilot scale research studies aimed at optimizing coagulation process applied to synthetic raw waters supplemented by adding commercial humic acid with low turbidity levels, explains how pH and turbidity can be controlled to maximize soluble NOM removal. The removal of NOM at various coagulant doses and coagulation pHs has been assessed through raw and treated (coagulated-settled water measurements of total organic carbon (TOC. For low turbidity waters, essential floc nucleation sites can be provided by creating synthetic turbidities, for example by adding clay. Adjusting the initial pH at 5.5 or adding clay before coagulant addition allows the formation of micro-flocs as well as formation of the insoluble flocs at low coagulant doses.

  6. Solution processable organic polymers and small molecules for bulk-heterojunction solar cells: A review

    International Nuclear Information System (INIS)

    Sharma, G. D.

    2011-01-01

    Solution processed bulk heterojunction (BHJ) organic solar cells (OSCs) have gained wide interest in past few years and are established as one of the leading next generation photovoltaic technologies for low cost power production. Power conversion efficiencies up to 6% and 6.5% have been reported in the literature for single layer and tandem solar cells, respectively using conjugated polymers. A recent record efficiency about 8.13% with active area of 1.13 cm 2 has been reported. However Solution processable small molecules have been widely applied for photovoltaic (PV) devices in recent years because they show strong absorption properties, and they can be easily purified and deposited onto flexible substrates at low cost. Introducing different donor and acceptor groups to construct donor--acceptor (D--A) structure small molecules has proved to be an efficient way to improve the properties of organic solar cells (OSCs). The power conversion efficiency about 4.4 % has been reported for OSCs based on the small molecules. This review deals with the recent progress of solution processable D--A structure small molecules and discusses the key factors affecting the properties of OSCs based on D--A structure small molecules: sunlight absorption, charge transport and the energy level of the molecules.

  7. Effect of natural and synthetic organics on the processing of ceramics

    Science.gov (United States)

    Schulz, Brett M.

    Dry pressing has been shown to be an efficient and cost effective method of manufacturing ceramic ware. Dry pressed parts are typically manufactured with a low moisture content which has the further advantage of eliminating the drying step that is necessary for plastic formed ware, i.e., jiggered or ram pressed. Problems associated with the use of dry pressing in an industrial setting involve the high loss rate during the bisque firing process and the poor surface finish of the green (unfired) ware. It was the goal of this research to improve the surface finish of dry pressed ware to a level that is satisfactory for decorating of the bisque fired ware. The adsorption of organic additives, specifically dispersants, on the surface of particles is an important aspect of ceramic processing. The interactions between organic additives, specifically sodium poly[acrylic acid] and poly[vinyl alcohol], have been demonstrated to result in phase separation into distinct domains during the spray-drying process. This phase separation leads to a poly[vinyl alcohol]-rich film on the surface of the granulate which will increase the P1 value, the pressure at the onset of granule deformation, of the granulate. This negative interaction between the organics increases the surface roughness of the dry pressed ware. The roughness of the industrially prepared ware was determined using an optical interferometer to set a baseline for improvements in the surface finish of the dry pressed ware. Blending of dried granulate was determined to significantly improve the surface finish of the ware. Alternative binders to replace a plasticized poly[vinyl alcohol] were observed to show improvements in the surface finish of the ware dry pressed in a semi-isostatic die. In summary the most important aspect to improving the surface finish of dry pressed ware, i.e. facilitating compaction, is the selection of the organic additives. Additives which are observed to have a negative interaction, i.e. to

  8. Organic Micropollutants Removal from Water by Oxidation and Other Processes:QSAR Models, Decision Support System and Hybrids of Processes

    KAUST Repository

    Sudhakaran, Sairam

    2013-08-01

    The presence of organic micropollutants (OMPs) in water is of great environmental concern. OMPs such as endocrine disruptors and certain pharmaceuticals have shown alarming effects on aquatic life. OMPs are included in the priority list of contaminants in several government directorate frameworks. The low levels of OMPs concentration (ng/L to μg/L) force the use of sophisticated analytical instruments. Although, the techniques to detect OMPs are progressing, the focus of current research is only on limited, important OMPs due to the high amount of time, cost and effort involved in analyzing them. Alternatively, quantitative structure activity relationship (QSAR) models help to screen processes and propose appropriate options without considerable experimental effort. QSAR models are well-established in regulatory bodies as a method to screen toxic chemicals. The goal of the present thesis was to develop QSAR models for OMPs removal by oxidation. Apart from the QSAR models, a decision support system (DSS) based on multi-criteria analysis (MCA) involving socio-economic-technical and sustainability aspects was developed. Also, hybrids of different water treatment processes were studied to propose a sustainable water treatment train for OMPs removal. In order to build the QSAR models, the ozone/hydroxyl radical rate constants or percent removals of the OMPs were compiled. Several software packages were used to 5 compute the chemical properties of OMPs and perform statistical analyses. For DSS, MCA was used since it allows the comparison of qualitative (non-monetary, non-metric) and quantitative criteria (e.g., costs). Quadrant plots were developed to study the hybrid of natural and advanced water treatment processes. The QSAR models satisfied both chemical and statistical criteria. The DSS resulted in natural treatment and ozonation as the preferred processes for OMPs removal. The QSAR models can be used as a screening tool for OMPs removal by oxidation. Moreover, the

  9. Potential donor families' experiences of organ and tissue donation-related communication, processes and outcome.

    Science.gov (United States)

    Marck, C H; Neate, S L; Skinner, M; Dwyer, B; Hickey, B B; Radford, S T; Weiland, T J; Jelinek, G A

    2016-01-01

    We aimed to describe the experiences of families of potential organ and tissue donors eligible for donation after circulatory death or brain death. Forty-nine family members of potential donors from four Melbourne hospitals were interviewed to assess their experiences of communication, processes and the outcomes of donation. Interviews were recorded, transcribed verbatim and analysed thematically. Families expressed a range of perspectives on themes of communication, hospital processes and care, the processes of consent and donation and reflected on decisions and outcomes. They expressed satisfaction overall with communication when receiving bad news, discussing death and donation. Honest and frank communication and being kept up-to-date and prepared for potential outcomes were important aspects for families, especially those of post circulatory death donors. Participants reported high levels of trust in healthcare professionals and satisfaction with the level of care received. Many donor families indicated the process was lengthy and stressful, but not significantly enough to adversely affect their satisfaction with the outcome. Both the decision itself and knowing others' lives had been saved provided them with consolation. No consenting families, and only some non-consenting families, regretted their decisions. Many expressed they would benefit from a follow-up opportunity to ask questions and clarify possible misunderstandings. Overall, while experiences varied, Australian families valued frank communication, trusted health professionals, were satisfied with the care their family member received and with donation processes, despite some apparent difficulties. Family satisfaction, infrequently assessed, is an important outcome and these findings may assist education for Australian organ donation professionals.

  10. Energy efficacy used to score organic refuse pretreatment processes for hydrogen anaerobic production.

    Science.gov (United States)

    Ruggeri, Bernardo; Luongo Malave, Andrea C; Bernardi, Milena; Fino, Debora

    2013-11-01

    The production of hydrogen through Anaerobic Digestion (AD) has been investigated to verify the efficacy of several pretreatment processes. Three types of waste with different carbon structures have been tested to obtain an extensive representation of the behavior of the materials present in Organic Waste (OW). The following types of waste were selected: Sweet Product Residue (SPR), i.e., confectionary residue removed from the market after the expiration date, Organic Waste Market (OWM) refuse from a local fruit and vegetable market, and Coffee Seed Skin (CSS) waste from a coffee production plant. Several pretreatment processes have been applied, including physical, chemical, thermal, and ultrasonic processes and a combination of these processes. Two methods have been used for the SPR to remove the packaging, manual (SPR) and mechanical (SPRex). A pilot plant that is able to extrude the refuse to 200atm was utilized. Two parameters have been used to score the different pretreatment processes: efficiency (ξ), which takes into account the amount of energy produced in the form of hydrogen compared with the available energy embedded in the refuse, and efficacy (η), which compares the efficiency obtained using the pretreated refuse with that obtained using the untreated refuse. The best result obtained for the SPR was the basic pretreatment, with η=6.4, whereas the thermal basic pretreatment gave the highest value, η=17.0 for SPRex. The best result for the OWM was obtained through a combination of basic/thermal pretreatments with η=9.9; lastly, the CSS residue with ultrasonic pretreatment produced the highest quantity of hydrogen, η=5.2. Copyright © 2013 Elsevier Ltd. All rights reserved.

  11. Solution-processed organic thermoelectric materials exhibiting doping-concentration-dependent polarity.

    Science.gov (United States)

    Hwang, Sunbin; Potscavage, William J; Yang, Yu Seok; Park, In Seob; Matsushima, Toshinori; Adachi, Chihaya

    2016-10-26

    Recent progress in conducting polymer-based organic thermoelectric generators (OTEGs) has resulted in high performance due to high Seebeck coefficient, high electrical conductivity (σ), and low thermal conductivity obtained by chemically controlling the materials's redox levels. In addition to improving the properties of individual OTEGs to obtain high performance, the development of solution processes for the fabrication of OTEG modules is necessary to realize large thermoelectric voltage and low-cost mass production. However, the scarcity of good candidates for soluble organic n-type materials limits the use of π-leg module structures consisting of complementary elements of p- and n-type materials because of unbalanced transport coefficients that lead to power losses. In particular, the extremely low σ of n-type materials compared with that of p-type materials is a serious challenge. In this study, poly(pyridinium phenylene) (P(PymPh)) was tested as an n-type semiconductor in solution-processed OTEGs, and the carrier density was controlled by a solution-based chemical doping process using the dopant sodium naphthalenide, a well-known reductant. The electronic structures and doping mechanism of P(PymPh) were explored based on the changes in UV-Vis-IR absorption, ultraviolet photoelectron, and X-ray photoelectron spectra. By controlling the dopant concentration, we demonstrate a maximum n-type power factor of 0.81 μW m -1 K -2 with high σ, and at higher doping concentrations, a switch from n-type to p-type TE operation. This is one of the first cases of a switch in polarity just by increasing the concentration of the reductant and may open a new route for simplified fabrication of complementary organic layers.

  12. Study and understanding of n/γ discrimination processes in organic plastic scintillators

    International Nuclear Information System (INIS)

    Hamel, Matthieu; Blanc, Pauline; Rocha, Licinio; Normand, Stephane; Pansu, Robert

    2013-01-01

    For 50 years, it was assumed that unlike liquid scintillators or organic crystals, plastic scintillators were not able to discriminate fast neutrons from gamma. In this work, we will demonstrate that triplet-triplet annihilations (which are responsible of n/γ discrimination) can occur even in plastic scintillators, following certain conditions. Thus, the presentation will deal with the chemical preparation, the characterization and the comparison of n/γ pulse shape discrimination of various plastic scintillators. To this aim, scale-up of the process allowed us to prepare a O 100 mm x*110 mm thick. (authors)

  13. In-situ observation of atomic self-organization processes in Xe nanocrystals embedded in Al

    International Nuclear Information System (INIS)

    Mitsuishi, K.; Song, M.; Furuya, K.; Birtcher, R. C.; Allen, C. W.; Donnelly, S. E.

    1998-01-01

    Self-organization processes in Xe nanocrystals embedded in Al are observed with in-situ high-resolution electron microscopy. Under electron irradiation, stacking fault type defects are produced in Xe nanocrystals. The defects recover in a layer by layer manner. Detailed analysis of the video reveals that the displacement of Xe atoms in the stacking fault was rather small for the Xe atoms at boundary between Xe and Al, suggesting the possibility of the stacking fault in Xe precipitate originating inside of precipitate, not at the Al/Xe interface

  14. Insights into the redox components of dissolved organic matters during stabilization process.

    Science.gov (United States)

    Yuan, Ying; Xi, Bei-Dou; He, Xiao-Song; Ma, Yan; Zhang, Hui; Li, Dan; Zhao, Xin-Yu

    2018-05-01

    The changes of dissolved organic matter (DOM) components during stabilization process play significant effects on its redox properties but are little reported. Composting is a stabilization process of DOM, during which both the components and electron transfer capacities (ETCs) of DOM change. The redox components within compost-derived DOM during the stabilization process are investigated in this study. The results show that compost-derived DOM contained protein-like, fulvic-like, and humic-like components. The protein-like component decreases during composting, whereas the fulvic- and humic-like components increase during the process. The electron-donating capacity (EDC), electron-accepting capacity (EAC), and ETC of compost-derived DOM all increase during composting but their correlations with the components presented significant difference. The humic-like components were the main functional component responsible for both EDC and ETC, whereas the protein- and fluvic-like components show negative effects with the EAC, EDC, and ETC, suggesting that the components within DOM have specific redox properties during the stabilization process. These findings are very meaningful for better understanding the geochemical behaviors of DOM in the environment.

  15. Anaerobic digestion of organic waste in RDF process - an initial investigation

    International Nuclear Information System (INIS)

    Khaironie Mohd Takip; Muhd Noor Muhd Yunus; Mohamad Puad Abu

    2004-01-01

    Disposing of municipal solid waste (MSW) into a landfill is a method of the past and creates the negative environmental impact. Growing awareness of this negative impact induced the development of Refuse Derived Fuel (RDF) from MSW RDF is not simply converting waste into energy but also enable waste to be recycled into heat and power. However, during the production of RDF, there are some spillages or rejects consist of organic fraction that still can be recovered. One of the options to treat these wastes is by biological treatment, the anaerobic digestion (AD). AD process could occur either naturally or in a controlled environment such as a biogas plant. The process produces a flammable gas known as biogas that can be used for processing heating, power generation, and in internal combustion engines. In general, the process provides not only pollution prevention but can also convert a disposal problem into a new profit centre. This paper will highlight the use of anaerobic technology to treat rejects derived from the RDF production process. (Author)

  16. Solution-processed white organic light-emitting devices based on small-molecule materials

    International Nuclear Information System (INIS)

    Wang Dongdong; Wu Zhaoxin; Zhang Xinwen; Wang Dawei; Hou Xun

    2010-01-01

    We investigated solution-processed films of 4,4'-bis(2,2-diphenylvinyl)-1,1'-bibenyl (DPVBi) and its blends with N,N'-bis(3-methylphenyl)-(1,1'-biphenyl)-4,4'-diamine (TPD) by atomic force microscopy (AFM). The AFM result shows that the solution-processed films are pin-free and their morphology is smooth enough to be used in OLEDs. We have developed a solution-processed white organic light-emitting device (WOLEDs) based on small-molecules, in which the light-emitting layer (EML) was formed by spin-coating the solution of small-molecules on top of the solution-processed hole-transporting layer. This WOLEDs, in which the EML consists of co-host (DPVBi and TPD), the blue dopant (4,4'-bis[2-(4-(N,N-diphenylamino)phenyl)vinyl]biphenyl) and the yellow dye (5,6,11,12-tetraphenylnaphtacene), has a current efficiency of 6.0 cd/A at a practical luminance of 1000 cd/m 2 , a maximum luminance of 22500 cd/m 2 , and its color coordinates are quite stable. Our research shows a possible approach to achieve efficient and low-cost small-molecule-based WOLEDs, which avoids the complexities of the co-evaporation process of multiple dopants and host materials in vacuum depositions.

  17. Fully solution-processed organic solar cells on metal foil substrates

    KAUST Repository

    Gaynor, Whitney

    2009-08-19

    We demonstrate fully solution-processed organic photovoltaic cells on metal foil substrates with power conversion efficiencies similar to those obtained in devices on transparent substrates. The cells are based on the regioregular poly- (3-hexylthiophene) and C61 butyric acid methyl ester bulk heterojunction system. The bottom electrode is a silver film whose workfunction is lowered by Cs2CO3 using spin-coating to serve as a cathode. The transparent top anode consists of a conductive polymer in combination with a solution-processed silver nanowire mesh that is laminated onto the devices. Each layer of the device, including the transparent electrode, is fabricated from solution, giving rise to the possibility of completely printed solar cells on low-cost substrates.

  18. From data processing to mental organs: an interdisciplinary path to cognitive neuroscience.

    Science.gov (United States)

    Patharkar, Manoj

    2011-01-01

    Human brain is a highly evolved coordinating mechanism in the species Homo sapiens. It is only in the last 100 years that extensive knowledge of the intricate structure and complex functioning of the human brain has been acquired, though a lot is yet to be known. However, from the beginning of civilisation, people have been conscious of a 'mind' which has been considered the origin of all scientific and cultural development. Philosophers have discussed at length the various attributes of consciousness. At the same time, most of the philosophical or scientific frameworks have directly or indirectly implied mind-body duality. It is now imperative that we develop an integrated approach to understand the interconnection between mind and consciousness on one hand and brain on the other. This paper begins with the proposition that the structure of the brain is analogous, at least to certain extent, to that of the computer system. Of course, it is much more sophisticated and complex. The second proposition is that the Chomskyean concept of 'mental organs' is a good working hypothesis that tries to characterise this complexity in terms of an innate cognitive framework. By following this dual approach, brain as a data processing system and brain as a superstructure of intricately linked mental organs, we can move toward a better understanding of 'mind' within the framework of empirical science. The one 'mental organ' studied extensively in Chomskyean terms is 'language faculty' which is unique in its relation to brain, mind and consciousness.

  19. Improving organic tandem solar cells based on water-processed nanoparticles by quantitative 3D nanoimaging.

    Science.gov (United States)

    Pedersen, E B L; Angmo, D; Dam, H F; Thydén, K T S; Andersen, T R; Skjønsfjell, E T B; Krebs, F C; Holler, M; Diaz, A; Guizar-Sicairos, M; Breiby, D W; Andreasen, J W

    2015-08-28

    Organic solar cells have great potential for upscaling due to roll-to-roll processing and a low energy payback time, making them an attractive sustainable energy source for the future. Active layers coated with water-dispersible Landfester particles enable greater control of the layer formation and easier access to the printing industry, which has reduced the use of organic solvents since the 1980s. Through ptychographic X-ray computed tomography (PXCT), we image quantitatively a roll-to-roll coated photovoltaic tandem stack consisting of one bulk heterojunction active layer and one Landfester particle active layer. We extract the layered morphology with structural and density information including the porosity present in the various layers and the silver electrode with high resolution in 3D. The Landfester particle layer is found to have an undesired morphology with negatively correlated top- and bottom interfaces, wide thickness distribution and only partial surface coverage causing electric short circuits through the layer. By top coating a polymer material onto the Landfester nanoparticles we eliminate the structural defects of the layer such as porosity and roughness, and achieve the increased performance larger than 1 V expected for a tandem cell. This study highlights that quantitative imaging of weakly scattering stacked layers of organic materials has become feasible by PXCT, and that this information cannot be obtained by other methods. In the present study, this technique specifically reveals the need to improve the coatability and layer formation of Landfester nanoparticles, thus allowing improved solar cells to be produced.

  20. Electrokinetic-enhanced bioremediation of organic contaminants: a review of processes and environmental applications.

    Science.gov (United States)

    Gill, R T; Harbottle, M J; Smith, J W N; Thornton, S F

    2014-07-01

    There is current interest in finding sustainable remediation technologies for the removal of contaminants from soil and groundwater. This review focuses on the combination of electrokinetics, the use of an electric potential to move organic and inorganic compounds, or charged particles/organisms in the subsurface independent of hydraulic conductivity; and bioremediation, the destruction of organic contaminants or attenuation of inorganic compounds by the activity of microorganisms in situ or ex situ. The objective of the review is to examine the state of knowledge on electrokinetic bioremediation and critically evaluate factors which affect the up-scaling of laboratory and bench-scale research to field-scale application. It discusses the mechanisms of electrokinetic bioremediation in the subsurface environment at different micro and macroscales, the influence of environmental processes on electrokinetic phenomena and the design options available for application to the field scale. The review also presents results from a modelling exercise to illustrate the effectiveness of electrokinetics on the supply electron acceptors to a plume scale scenario where these are limiting. Current research needs include analysis of electrokinetic bioremediation in more representative environmental settings, such as those in physically heterogeneous systems in order to gain a greater understanding of the controlling mechanisms on both electrokinetics and bioremediation in those scenarios. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

  1. Value Assessment Frameworks for HTA Agencies: The Organization of Evidence-Informed Deliberative Processes.

    Science.gov (United States)

    Baltussen, Rob; Jansen, Maarten Paul Maria; Bijlmakers, Leon; Grutters, Janneke; Kluytmans, Anouck; Reuzel, Rob P; Tummers, Marcia; der Wilt, Gert Jan van

    2017-02-01

    Priority setting in health care has been long recognized as an intrinsically complex and value-laden process. Yet, health technology assessment agencies (HTAs) presently employ value assessment frameworks that are ill fitted to capture the range and diversity of stakeholder values and thereby risk compromising the legitimacy of their recommendations. We propose "evidence-informed deliberative processes" as an alternative framework with the aim to enhance this legitimacy. This framework integrates two increasingly popular and complementary frameworks for priority setting: multicriteria decision analysis and accountability for reasonableness. Evidence-informed deliberative processes are, on one hand, based on early, continued stakeholder deliberation to learn about the importance of relevant social values. On the other hand, they are based on rational decision-making through evidence-informed evaluation of the identified values. The framework has important implications for how HTA agencies should ideally organize their processes. First, HTA agencies should take the responsibility of organizing stakeholder involvement. Second, agencies are advised to integrate their assessment and appraisal phases, allowing for the timely collection of evidence on values that are considered relevant. Third, HTA agencies should subject their decision-making criteria to public scrutiny. Fourth, agencies are advised to use a checklist of potentially relevant criteria and to provide argumentation for how each criterion affected the recommendation. Fifth, HTA agencies must publish their argumentation and install options for appeal. The framework should not be considered a blueprint for HTA agencies but rather an aspirational goal-agencies can take incremental steps toward achieving this goal. Copyright © 2017 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

  2. Characteristics and fate of natural organic matter during UV oxidation processes.

    Science.gov (United States)

    Ahn, Yongtae; Lee, Doorae; Kwon, Minhwan; Choi, Il-Hwan; Nam, Seong-Nam; Kang, Joon-Wun

    2017-10-01

    Advanced oxidation processes (AOPs) are widely used in water treatments. During oxidation processes, natural organic matter (NOM) is modified and broken down into smaller compounds that affect the characteristics of the oxidized NOM by AOPs. In this study, NOM was characterized and monitored in the UV/hydrogen peroxide (H 2 O 2 ) and UV/persulfate (PS) processes using a liquid chromatography-organic carbon detector (LC-OCD) technique, and a combination of excitation-emission matrices (EEM) and parallel factor analysis (PARAFAC). The percentages of mineralization of NOM in the UV/H 2 O 2 and UV/PS processes were 20.5 and 83.3%, respectively, with a 10 mM oxidant dose and a contact time of 174 s (UV dose: approximately 30,000 mJ). Low-pressure, Hg UV lamp (254 nm) was applied in this experiment. The steady-state concentration of SO 4 - was 38-fold higher than that of OH at an oxidant dose of 10 mM. With para-chlorobenzoic acid (pCBA) as a radical probe compound, we experimentally determined the rate constants of Suwannee River NOM (SRNOM) with OH (k OH/NOM  = 3.3 × 10 8  M -1 s -1 ) and SO 4 - (k SO4-/NOM  = 4.55 × 10 6  M -1 s -1 ). The hydroxyl radical and sulfate radical showed different mineralization pathways of NOM, which have been verified by the use of LC-OCD and EEM/PARAFAC. Consequently, higher steady-state concentrations of SO 4 - , and different reaction preferences of OH and SO 4 - with the NOM constituent had an effect on the mineralization efficiency. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. The Identification and Modeling of Business Processes of the Quality Management System in an Educational Organization: Theory and Practice

    Directory of Open Access Journals (Sweden)

    Stankevych Iryna V.

    2017-03-01

    Full Text Available The aim of the article is to ensure effectiveness of implementation of management objectives of an educational organization by identifying business processes of the quality management system of the educational organization and justifying the choice of language and diagrams of their modeling. The author emphasizes that the approach to identifying business processes of the quality management system of an educational organization should be based not on the types but on the results of the organization’s activity in higher education. It is determined that an effective approach to identifying business processes of the quality management system of an educational organization should be based on the life cycle of the educational service (quality loop, the requirements of the ISO 9001: 2015 standard for building the processes of the quality management system and the standardized list of business processes International Benchmarking Clearinghouse. For further implementation of the quality management system, the author developed a contextual diagram of the system, which is decomposed into processes of level “0” and level “1”. The paper discusses the advantages and disadvantages of various modeling languages applicable to business process virtualization, in particular the unified UML modeling language, which uses a number of diagrams to virtualize business processes of complex organizations. The practical recommendations developed for the identification and modeling of business processes in the quality management system will facilitate an effective implementation of such systems in activities of educational organizations, which will further ensure satisfaction of customer requirements and implementation of management objectives.

  4. Reconstructing Space- and Energy-Dependent Exciton Generation in Solution-Processed Inverted Organic Solar Cells.

    Science.gov (United States)

    Wang, Yuheng; Zhang, Yajie; Lu, Guanghao; Feng, Xiaoshan; Xiao, Tong; Xie, Jing; Liu, Xiaoyan; Ji, Jiahui; Wei, Zhixiang; Bu, Laju

    2018-04-25

    Photon absorption-induced exciton generation plays an important role in determining the photovoltaic properties of donor/acceptor organic solar cells with an inverted architecture. However, the reconstruction of light harvesting and thus exciton generation at different locations within organic inverted device are still not well resolved. Here, we investigate the film depth-dependent light absorption spectra in a small molecule donor/acceptor film. Including depth-dependent spectra into an optical transfer matrix method allows us to reconstruct both film depth- and energy-dependent exciton generation profiles, using which short-circuit current and external quantum efficiency of the inverted device are simulated and compared with the experimental measurements. The film depth-dependent spectroscopy, from which we are able to simultaneously reconstruct light harvesting profile, depth-dependent composition distribution, and vertical energy level variations, provides insights into photovoltaic process. In combination with appropriate material processing methods and device architecture, the method proposed in this work will help optimizing film depth-dependent optical/electronic properties for high-performance solar cells.

  5. Application of the Marcus theory to description of the kinetics of reduction processes of organic cations

    International Nuclear Information System (INIS)

    Bogillo, V.I.; Lobanov, V.V.; Gragerov, I.P.

    1987-01-01

    The calculation of the rate constants for the processes in the reduction of diazonium, tropylium, verdazylium, and pyrylium cations by various organic electron donors, using the equations of the Marcus theory with allowance for the reorganization energy of only the outer coordination sphere, leads to values which are one to seven orders of magnitude higher than the experimental values. By quantum-chemical calculations it was shown that the reduction of diazonium and tropylium cations to the corresponding radicals is accompanied by a substantial change in the structure of the reagents. This leads to high values for the reorganization energy of the inner coordination sphere of the cations, which must be taken into account during calculation of the rate constants. The differences in the rate constants of the processes of direct electron transfer from the electron donors to the organic cations and the recombination of these reagents depend on the dissociation energy of the bond of the cation with the donor leading to the electron transfer products

  6. Treatment of persistent organic pollutants in wastewater using hydrodynamic cavitation in synergy with advanced oxidation process.

    Science.gov (United States)

    Badmus, Kassim Olasunkanmi; Tijani, Jimoh Oladejo; Massima, Emile; Petrik, Leslie

    2018-03-01

    Persistent organic pollutants (POPs) are very tenacious wastewater contaminants. The consequences of their existence have been acknowledged for negatively affecting the ecosystem with specific impact upon endocrine disruption and hormonal diseases in humans. Their recalcitrance and circumvention of nearly all the known wastewater treatment procedures are also well documented. The reported successes of POPs treatment using various advanced technologies are not without setbacks such as low degradation efficiency, generation of toxic intermediates, massive sludge production, and high energy expenditure and operational cost. However, advanced oxidation processes (AOPs) have recently recorded successes in the treatment of POPs in wastewater. AOPs are technologies which involve the generation of OH radicals for the purpose of oxidising recalcitrant organic contaminants to their inert end products. This review provides information on the existence of POPs and their effects on humans. Besides, the merits and demerits of various advanced treatment technologies as well as the synergistic efficiency of combined AOPs in the treatment of wastewater containing POPs was reported. A concise review of recently published studies on successful treatment of POPs in wastewater using hydrodynamic cavitation technology in combination with other advanced oxidation processes is presented with the highlight of direction for future research focus.

  7. Fuzzy sets on step of planning of experiment for organization and management of construction processes

    Directory of Open Access Journals (Sweden)

    Lapidus Azariy

    2016-01-01

    Full Text Available In this article, problems of mathematical modeling and experiment planning of the organization and management of construction. The authors designated the basic restrictions and the difficulties in this field. Concluded that the planning of research experiment is possible in the information sphere with using of heuristic, graphical, mathematical models, as well as neural networks and genetic algorithms. The authors note the need for use of expert information in the case of the formalization of quality parameters. The article presented an overview of the translation methods of qualitative information into mathematical language. Comparison of methods the qualimetry of USSR scientists, the analytic hierarchy process and fuzzy set theory were performed. The benefits of the latter for interpretation of qualitative parameters were identified. The authors have given many examples of application fuzzy sets for formalization of organizational factors of construction processes. Finally, there conclusion was made about progressiveness and effectiveness of fuzzy set theory to describe the qualitative parameters of organization and management of construction.

  8. Self-Aligned Metal Electrodes in Fully Roll-to-Roll Processed Organic Transistors

    Directory of Open Access Journals (Sweden)

    Marja Vilkman

    2016-01-01

    Full Text Available We demonstrate the production of organic bottom gate transistors with self-aligned electrodes, using only continuous roll-to-roll (R2R techniques. The self-alignment allows accurate <5 µm layer-to-layer registration, which is usually a challenge in high-speed R2R environments as the standard registration methods are limited to the millimeter range—or, at best, to tens of µm if online cameras and automatic web control are utilized. The improved registration enables minimizing the overlap between the source/drain electrodes and the gate electrode, which is essential for minimizing the parasitic capacitance. The complete process is a combination of several techniques, including evaporation, reverse gravure, flexography, lift-off, UV exposure and development methods—all transferred to a continuous R2R pilot line. Altogether, approximately 80 meters of devices consisting of thousands of transistors were manufactured in a roll-to-roll fashion. Finally, a cost analysis is presented in order to ascertain the main costs and to predict whether the process would be feasible for the industrial production of organic transistors.

  9. Photo-physics of third-order nonlinear optical processes in organic dyes

    International Nuclear Information System (INIS)

    Delysse, Stephane

    1997-01-01

    We study some aspects of the nonlinear picosecond photo-physics in organic dyes using Kerr ellipsometry. The aim is to establish link between the photo-physics and nonlinear optics in these compounds. First, we study coherent processes directly linked to the third-order susceptibility. Thus, we measure two-photon absorption spectra of large internal charge transfer dyes. We take into account all coupling between three electronic states which can interfere to explain the particular response of some stilbene dyes. On the second hand, we expose a more photophysical approach to determine the S 1 → S n transition energies and moments using the measurement of excited state absorption cross sections. These results allow the prediction of the susceptibilities relevant to alternative nonlinear optical methods. Nevertheless, the stationary approach hides the complex relaxation processes which can take place in organic dyes. As an illustration, we study the formation and disappearance of a TICT (Twisted intramolecular charge transfer) in a pyrylium salt in solvents of increasing viscosity. (author) [fr

  10. Scalable organic solvent free supercritical fluid spray drying process for producing dry protein formulations.

    Science.gov (United States)

    Nuchuchua, O; Every, H A; Hofland, G W; Jiskoot, W

    2014-11-01

    In this study, we evaluated the influence of supercritical carbon dioxide (scCO2) spray drying conditions, in the absence of organic solvent, on the ability to produce dry protein/trehalose formulations at 1:10 and 1:4 (w/w) ratios. When using a 4L drying vessel, we found that decreasing the solution flow rate and solution volume, or increasing the scCO2 flow rate resulted in a significant reduction in the residual water content in dried products (Karl Fischer titration). The best conditions were then used to evaluate the ability to scale the scCO2 spray drying process from 4L to 10L chamber. The ratio of scCO2 and solution flow rate was kept constant. The products on both scales exhibited similar residual moisture contents, particle morphologies (SEM), and glass transition temperatures (DSC). After reconstitution, the lysozyme activity (enzymatic assay) and structure (circular dichroism, HP-SEC) were fully preserved, but the sub-visible particle content was slightly increased (flow imaging microscopy, nanoparticle tracking analysis). Furthermore, the drying condition was applicable to other proteins resulting in products of similar quality as the lysozyme formulations. In conclusion, we established scCO2 spray drying processing conditions for protein formulations without an organic solvent that holds promise for the industrial production of dry protein formulations. Copyright © 2014 Elsevier B.V. All rights reserved.

  11. Environmental processes leading to the presence of organically bound plutonium in plant tissues consumed by animals

    International Nuclear Information System (INIS)

    Wildung, R.E.; Garland, T.R.; Cataldo, D.A.

    1979-01-01

    Using a proposed model for Pu behaviour to integrate current knowledge, information is presented on the chemical/biochemical processes governing the form of Pu in soils and plants and the relationship of these phenomena to gut absorption in animals. Regardless of the source term, Pu behaviour in the soil will be governed by the chemistry of Pu(IV), which predominates over Pu(VI) due to reductive reactions in the soil and at the plant root surface. The soil behaviour of Pu(IV) is governed by (1) hydrolysis, which results in insolubilization and sorption on solid phases, and (2) complexation with inorganic and organic ligands, which stabilize Pu(IV) against hydrolysis and increase solubility. These competing processes likely represent the rate-limiting step in the ingestion pathway because plants do not effectively discriminate against the soluble Pu(IV) ion. Following dissociation of soil Pu(IV) complexes at the outer root surface, Pu is transported across the plant root membrane as the Pu(IV) ion and translocated as Pu(IV) complexes with plant organic ligands. Redistribution of Pu occurs as the plant grows, with initial increases in stem tissues followed by accumulation in roots as the plant matures. The Pu concentration decreases up the plant and seeds contain the lowest Pu concentrations. The gastro-intestinal absorption of Pu requires the presence of soluble Pu forms and hydrolysis/complexation reactions in the gut likely govern solubility. The acidity of the gut is not sufficient to retard hydrolysis of Pu(IV). Therefore, the gastro-intestinal absorption of Pu organically bound in plant tissues is increased relative to Pu administered in hydrolysable solutions. (author)

  12. Processes Affecting Agricultural Drainwater Quality and Organic Carbon Loads in California's Sacramento–San Joaquin Delta

    Directory of Open Access Journals (Sweden)

    Steven J. Deverel

    2007-05-01

    Full Text Available From 2000 to 2003 we quantified drain flow, drain-and ground-water chemistry and hydrogeologic conditions on Twitchell Island in the Sacramento-San Joaquin Delta. The primary objective was to quantify processes affecting organic carbon concentrations and loads in agricultural drainage water. We collected physical and chemical data in southern and northern areas: TN and TS, respectively. Corn grew in both areas during the spring and summer. The peat soils in the TN area are more decomposed than those in the TS area. Results elucidate processes affecting drain flow and concentrations under varying hydrologic conditions. During May through November, groundwater flows from the permanently saturated zone to drainage ditches, and the resulting average drainage-water quality and dissolved organic carbon (DOC concentration was similar to the groundwater; the median DOC loads in the TN and TS study areas ranged from 9 to 27 g C/ha-day. The major ion chemistry and stable isotope data confirmed that groundwater was the primary source of drainflow. In contrast, during December through April the drainwater is supplied from the shallow, variably saturated soil-zone. The DOC concentrations, major-ion chemistry, and stable isotope data indicate that the shallow-zone water is partially evaporated and oxidized. Higher flows and DOC concentrations during these months result in higher median DOC loads, which ranged from 84 to 280 g C/ha-day. During December through April, increasing groundwater levels in the shallow peat layers and mobilization of organic carbon result in high drain flow and increased trihalomethane precursor concentrations and loads. On a per mass DOC basis, drain water collected during high flow periods is less likely to form THMs than during low flow periods. However, the high flows and subsequent high concentrations contribute to substantially higher trihalomethane precursor and DOC loads.

  13. Single Vs Mixed Organic Cation for Low Temperature Processed Perovskite Solar Cells

    International Nuclear Information System (INIS)

    Mahmud, Md Arafat; Elumalai, Naveen Kumar; Upama, Mushfika Baishakhi; Wang, Dian; Wright, Matthew; Chan, Kah Howe; Xu, Cheng; Haque, Faiazul; Uddin, Ashraf

    2016-01-01

    Highlights: • Low temperature processed ZnO based single & mixed organic cation perovskite device. • 37% higher PCE in mixed cation perovskite solar cells (PSCs) than single cation ones. • Mixed cation PSCs exhibit significantly reduced photocurrent hysteresis. • Mixed cation PSCs demonstrate three fold higher device stability than single cation PSCs. • Electronic properties are analyzed using Electrochemical Impedance Spectroscopy. - Abstract: The present work reports a comparative study between single and mixed organic cation based MAPbI 3 and MA 0.6 FA 0.4 PbI 3 perovskite devices fabricated in conjunction with low temperature processed (<150 °C) ZnO electron transport layers. MA 0.6 FA 0.4 PbI 3 perovskite devices demonstrate 37% higher power conversion efficiency compared to MAPbI 3 perovskite devices developed on the ZnO ETL. In addition, MA 0.6 FA 0.4 PbI 3 devices exhibit very low photocurrent hysteresis and they are three-fold more stable than conventional MAPbI 3 PSCs (perovskite solar cells). An in-depth analysis on the charge transport properties in both fresh and aged devices has been carried out using electrochemical impedance spectroscopy analysis to comprehend the enhanced device stability of the mixed perovskite devices developed on the ZnO ETL. The study also investigates into the interfacial charge transfer characteristics associated with the ZnO/mixed organic cation perovskite interface and concomitant influence on the inherent electronic properties.

  14. Halogenation processes of secondary organic aerosol and implications on halogen release mechanisms

    Directory of Open Access Journals (Sweden)

    J. Ofner

    2012-07-01

    Full Text Available Reactive halogen species (RHS, such as X·, X2 and HOX containing X = chlorine and/or bromine, are released by various sources like photo-activated sea-salt aerosol or from salt pans, and salt lakes. Despite many studies of RHS reactions, the potential of RHS reacting with secondary organic aerosol (SOA and organic aerosol derived from biomass-burning (BBOA has been neglected. Such reactions can constitute sources of gaseous organohalogen compounds or halogenated organic matter in the tropospheric boundary layer and can influence physicochemical properties of atmospheric aerosols.

    Model SOA from α-pinene, catechol, and guaiacol was used to study heterogeneous interactions with RHS. Particles were exposed to molecular chlorine and bromine in an aerosol smog-chamber in the presence of UV/VIS irradiation and to RHS, released from simulated natural halogen sources like salt pans. Subsequently, the aerosol was characterized in detail using a variety of physicochemical and spectroscopic methods. Fundamental features were correlated with heterogeneous halogenation, which results in new functional groups (FTIR spectroscopy, changes UV/VIS absorption, chemical composition (ultrahigh resolution mass spectroscopy (ICR-FT/MS, or aerosol size distribution. However, the halogen release mechanisms were also found to be affected by the presence of organic aerosol. Those interaction processes, changing chemical and physical properties of the aerosol are likely to influence e.g. the ability of the aerosol to act as cloud condensation nuclei, its potential to adsorb other gases with low-volatility, or its contribution to radiative forcing and ultimately the Earth's radiation balance.

  15. Reduction of COD in wastewater from an organized tannery industrial region by Electro-Fenton process

    International Nuclear Information System (INIS)

    Kurt, Ugur; Apaydin, Omer; Gonullu, M. Talha

    2007-01-01

    Advanced oxidation processes (AOPs) have led the way in the treatment of aqueous waste and are rapidly becoming the chosen technology for many applications. In this paper, COD reduction potential of leather tanning industry wastewaters by Electro-Fenton (EF) oxidation, as one of the AOPs, was experimentally evaluated. The wastewater sample was taken from an outlet of an equalization basin in a common treatment plant of an organized tannery industrial region in Istanbul, Turkey. Treatment of the wastewater was carried out by an electrochemical batch reactor equipped with two iron electrodes, which were connected parallel to each other. The oxidation process was studied for optimization of H 2 O 2 and the electricity consumptions were observed at different contact times under different pH conditions (3.0, 5.0 and 7.2). In each case, electricity consumption for decreased COD mass was estimated. In this process, COD was reduced by 60-70% within 10 min. By taking into consideration the local sewerage discharge limit, applicability of EF process for the tannery wastewaters was evaluated

  16. Reduction of COD in wastewater from an organized tannery industrial region by Electro-Fenton process

    Energy Technology Data Exchange (ETDEWEB)

    Kurt, Ugur [Yildiz Technical University, Environmental Engineering Department, 34349 Istanbul (Turkey)]. E-mail: ukurt@yildiz.edu.tr; Apaydin, Omer [Yildiz Technical University, Environmental Engineering Department, 34349 Istanbul (Turkey)]. E-mail: apaydin@yildiz.edu.tr; Gonullu, M. Talha [Yildiz Technical University, Environmental Engineering Department, 34349 Istanbul (Turkey)]. E-mail: gonul@yildiz.edu.tr

    2007-05-08

    Advanced oxidation processes (AOPs) have led the way in the treatment of aqueous waste and are rapidly becoming the chosen technology for many applications. In this paper, COD reduction potential of leather tanning industry wastewaters by Electro-Fenton (EF) oxidation, as one of the AOPs, was experimentally evaluated. The wastewater sample was taken from an outlet of an equalization basin in a common treatment plant of an organized tannery industrial region in Istanbul, Turkey. Treatment of the wastewater was carried out by an electrochemical batch reactor equipped with two iron electrodes, which were connected parallel to each other. The oxidation process was studied for optimization of H{sub 2}O{sub 2} and the electricity consumptions were observed at different contact times under different pH conditions (3.0, 5.0 and 7.2). In each case, electricity consumption for decreased COD mass was estimated. In this process, COD was reduced by 60-70% within 10 min. By taking into consideration the local sewerage discharge limit, applicability of EF process for the tannery wastewaters was evaluated.

  17. All-Solution-Processed Metal-Oxide-Free Flexible Organic Solar Cells with Over 10% Efficiency.

    Science.gov (United States)

    Song, Wei; Fan, Xi; Xu, Bingang; Yan, Feng; Cui, Huiqin; Wei, Qiang; Peng, Ruixiang; Hong, Ling; Huang, Jiaming; Ge, Ziyi

    2018-05-16

    All-solution-processing at low temperatures is important and desirable for making printed photovoltaic devices and also offers the possibility of a safe and cost-effective fabrication environment for the devices. Herein, an all-solution-processed flexible organic solar cell (OSC) using poly(3,4-ethylenedioxythiophene):poly-(styrenesulfonate) electrodes is reported. The all-solution-processed flexible devices yield the highest power conversion efficiency of 10.12% with high fill factor of over 70%, which is the highest value for metal-oxide-free flexible OSCs reported so far. The enhanced performance is attributed to the newly developed gentle acid treatment at room temperature that enables a high-performance PEDOT:PSS/plastic underlying substrate with a matched work function (≈4.91 eV), and the interface engineering that endows the devices with better interface contacts and improved hole mobility. Furthermore, the flexible devices exhibit an excellent mechanical flexibility, as indicated by a high retention (≈94%) of the initial efficiency after 1000 bending cycles. This work provides a simple route to fabricate high-performance all-solution-processed flexible OSCs, which is important for the development of printing, blading, and roll-to-roll technologies. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Controlled synthesis of organic single-crystalline nanowires via the synergy approach of the bottom-up/top-down processes.

    Science.gov (United States)

    Zhuo, Ming-Peng; Zhang, Ye-Xin; Li, Zhi-Zhou; Shi, Ying-Li; Wang, Xue-Dong; Liao, Liang-Sheng

    2018-03-15

    The controlled fabrication of organic single-crystalline nanowires (OSCNWs) with a uniform diameter in the nanoscale via the bottom-up approach, which is just based on weak intermolecular interaction, is a great challenge. Herein, we utilize the synergy approach of the bottom-up and the top-down processes to fabricate OSCNWs with diameters of 120 ± 10 nm through stepwise evolution processes. Specifically, the evolution processes vary from the self-assembled organic micro-rods with a quadrangular pyramid-like end-structure bounded with {111}s and {11-1}s crystal planes to the "top-down" synthesized organic micro-rods with the flat cross-sectional {002}s plane, to the organic micro-tubes with a wall thickness of ∼115 nm, and finally to the organic nanowires. Notably, the anisotropic etching process caused by the protic solvent molecules (such as ethanol) is crucial for the evolution of the morphology throughout the whole top-down process. Therefore, our demonstration opens a new avenue for the controlled-fabrication of organic nanowires, and also contributes to the development of nanowire-based organic optoelectronics such as organic nanowire lasers.

  19. Simple solution-processed CuOX as anode buffer layer for efficient organic solar cells

    International Nuclear Information System (INIS)

    Shen, Wenfei; Yang, Chunpeng; Bao, Xichang; Sun, Liang; Wang, Ning; Tang, Jianguo; Chen, Weichao; Yang, Renqiang

    2015-01-01

    Graphical abstract: - Highlights: • Simple solution-processed CuO X hole transport layer for efficient organic solar cell. • Good photovoltaic performances as hole transport layer in OSCs with P3HT and PBDTTT-C as donor materials. • The device with CuO X as hole transport layer shows great improved stability compared with that of device with PEDOT:PSS as hole transport layer. - Abstract: A simple, solution-processed ultrathin CuO X anode buffer layer was fabricated for high performance organic solar cells (OSCs). XPS measurement demonstrated that the CuO X was the composite of CuO and Cu 2 O. The CuO X modified ITO glass exhibit a better surface contact with the active layer. The photovoltaic performance of the devices with CuO X layer was optimized by varying the thickness of CuO X films through changing solution concentration. With P3HT:PC 61 BM as the active layer, we demonstrated an enhanced PCE of 4.14% with CuO X anode buffer layer, compared with that of PEDOT:PSS layer. The CuO X layer also exhibits efficient photovoltaic performance in devices with PBDTTT-C:PC 71 BM as the active layer. The long-term stability of CuO X device is better than that of PEDOT:PSS device. The results indicate that the easy solution-processed CuO X film can act as an efficient anode buffer layer for high-efficiency OSCs

  20. Co-regulation of redox processes in freshwater wetlands as a function of organic matter availability?

    International Nuclear Information System (INIS)

    Alewell, C.; Paul, S.; Lischeid, G.; Storck, F.R.

    2008-01-01

    Wetlands have important filter functions in landscapes but are considered to be the biggest unknowns regarding their element dynamics under global climate change. Information on sink and source function of sulphur, nitrogen, organic matter and acidity in wetlands is crucial for freshwater regeneration. Recent results indicate that redox processes are not completely controlled by the sequential reduction chain (that is electron acceptor availability) but that electron donor availability may be an important regulator. Our hypothesis was that only sites which are limited in their electron donor availability (low concentrations of dissolved organic carbon (DOC)) follow the concept of the sequential reduction chain. We compared the results of two freshwater wetland systems: 1) three forested fens within a boreal spruce catchment in a low mountain range in southern Germany (high DOC regime) and 2) three floodplain soils within a groundwater enrichment area in the Rhein valley in northwest Switzerland (low DOC regime). Micro scale investigations (a few cm 3 ) with dialyse chambers as well as soil solution and groundwater concentrations at the forested fens (high DOC regime) indicated simultaneous consumption of nitrate and sulphate with release of iron, manganese and methane (CH 4 ) as well as an enrichment in stable sulphur isotopes indicating a co-existence of processes attributed to different redox gradients. Soil and aquifer gas measurements down to 4.6 m at the groundwater enrichment site (low DOC regime and carbon limitation) showed extreme high rates of metabolism with carbon dioxide (CO 2 ) , dinitrous oxide (N 2 O) and CH 4 concentrations reaching fifty, thirty and three times atmospheric concentrations, respectively. Simultaneously, groundwater oxygen (O 2 ) saturation was between 50 and 95%. We concluded that independent of DOC regime the sequential reduction chain was not a suitable concept in our systems. Instead of electron acceptor or donor availability

  1. Source and Processes of Dissolved Organic Matter in a Bangladesh Groundwater

    Science.gov (United States)

    McKnight, D. M.; Simone, B. E.; Mladenov, N.; Zheng, Y.; Legg, T. M.; Nemergut, D.

    2010-12-01

    Arsenic contamination of groundwater is a global health crisis, especially in Bangladesh where an estimated 40 million people are at risk. The release of geogenic arsenic bound to sediments into groundwater is thought to be influenced by dissolved organic matter (DOM) through several biogeochemical processes. Abiotically, DOM can promote the release of sediment bound As through the formation of DOM-As complexes and competitive interactions between As and DOM for sorption sites on the sediment. Additionally, the labile portion of groundwater DOM can serve as an electron donor to support microbial growth and the more recalcitrant humic DOM may serve as an electron shuttle, facilitating the eventual reduction of ferric iron present as iron oxides in sediments and consequently the mobilization of sorbed As and organic material. The goal of this study is to understand the source of DOM in representative Bangladesh groundwaters and the DOM sorption processes that occur at depth. We report chemical characteristics of representative DOM from a surface water, a shallow low-As groundwater, mid-depth high-As groundwater from the Araihazar region of Bangladesh. The humic DOM from groundwater displayed a more terrestrial chemical signature, indicative of being derived from plant and soil precursor materials, while the surface water humic DOM had a more microbial signature, suggesting an anthropogenic influence. In terms of biogeochemical processes occurring in the groundwater system, there is evidence from a diverse set of chemical characteristics, ranging from 13C-NMR spectroscopy to the analysis of lignin phenols, for preferential sorption onto iron oxides influencing the chemistry and reactivity of humic DOM in high As groundwater in Bangladesh. Taken together, these results provide chemical evidence for anthropogenic influence and the importance of sorption reactions at depth controlling the water quality of high As groundwater in Bangladesh.

  2. Photochemical processing of organic aerosol at nearby continental sites: contrast between urban plumes and regional aerosol

    Science.gov (United States)

    Slowik, J. G.; Brook, J.; Chang, R. Y.-W.; Evans, G. J.; Hayden, K.; Jeong, C.-H.; Li, S.-M.; Liggio, J.; Liu, P. S. K.; McGuire, M.; Mihele, C.; Sjostedt, S.; Vlasenko, A.; Abbatt, J. P. D.

    2011-03-01

    As part of the BAQS-Met 2007 field campaign, Aerodyne time-of-flight aerosol mass spectrometers (ToF-AMS) were deployed at two sites in southwestern Ontario from 17 June to 11 July 2007. One instrument was located at Harrow, ON, a rural, agriculture-dominated area approximately 40 km southeast of the Detroit/Windsor/Windsor urban area and 5 km north of Lake Erie. The second instrument was located at Bear Creek, ON, a rural site approximately 70 km northeast of the Harrow site and 50 km east of Detroit/Windsor. Positive matrix factorization analysis of the combined organic mass spectral dataset yields factors related to secondary organic aerosol (SOA), direct emissions, and a factor tentatively attributed to the reactive uptake of isoprene and/or condensation of its early generation reaction products. This is the first application of PMF to simultaneous AMS measurements at different sites, an approach which allows for self-consistent, direct comparison of the datasets. Case studies are utilized to investigate processing of SOA from (1) fresh emissions from Detroit/Windsor and (2) regional aerosol during periods of inter-site flow. A strong correlation is observed between SOA/excess CO and photochemical age as represented by the NOx/NOy ratio for Detroit/Windsor outflow. Although this correlation is not evident for more aged air, measurements at the two sites during inter-site transport nevertheless show evidence of continued atmospheric processing by SOA production. However, the rate of SOA production decreases with airmass age from an initial value of ~10.1 μg m-3 ppmvCO-1 h-1 for the first ~10 h of plume processing to near-zero in an aged airmass (i.e. after several days). The initial SOA production rate is comparable to the observed rate in Mexico City over similar timescales.

  3. Effect of soil organic matter on antimony bioavailability after the remediation process

    International Nuclear Information System (INIS)

    Nakamaru, Yasuo Mitsui; Martín Peinado, Francisco José

    2017-01-01

    We evaluated the long-term (18 year) and short-term (4 weeks) changes of Sb in contaminated soil with SOM increase under remediation process. In the Aznalcóllar mine accident (1998) contaminated area, the remediation measurement implemented the Guadiamar Green Corridor, where residual pollution is still detected. Soils of the re-vegetated area (O2) with high pH and high SOM content, moderately re-vegetated area (O1) and unvegetated area (C) were sampled. Soil pH, CEC, SOM amount and soil Sb forms were evaluated. Soil Sb was measured as total, soluble, exchangeable, EDTA extractable, acid oxalate extractable, and pyro-phosphate extractable fractions. Further, the short-term effect of artificial organic matter addition was also evaluated with incubation study by adding compost to the sampled soil from C, O1 and O2 areas. After 4 weeks of incubation, soil chemical properties and Sb forms were evaluated. In re-vegetated area (O2), soil total Sb was two times lower than in unvegetated area (C); however, soluble, exchangeable, and EDTA extractable Sb were 2–8 times higher. The mobile/bioavailable Sb increase was also observed after 4 weeks of incubation with the addition of compost. Soluble, exchangeable, and EDTA extractable Sb was increased 2–4 times by compost addition. By the linear regression analysis, the significantly related factors for soluble, exchangeable, and EDTA extractable Sb values were pH, CEC, and SOM, respectively. Soluble Sb increase was mainly related to pH rise. Exchangeable Sb should be bound by SOM-metal complex and increased with CEC. EDTA extractable fraction should be increased with increase of SOM as SOM-Fe associated Sb complex. From these results, it was shown that increase of SOM under natural conditions or application of organic amendment under remediation process should increase availability of Sb to plants. - Highlights: • The effect of SOM on Sb availability was evaluated after the remediation process. • Increase in SOM raised

  4. [Characteristics of volatile organic compounds (VOCs) emission from electronic products processing and manufacturing factory].

    Science.gov (United States)

    Cui, Ru; Ma, Yong-Liang

    2013-12-01

    Based on the EPA method T0-11 and 14/15 for measurement of toxic organics in air samples, fast VOCs detector, Summa canister and DNPH absorbent were used to determine the VOCs concentrations and the compositions in the ambient air of the workshops for different processes as well as the emission concentration in the exhaust gas. In all processes that involved VOCs release, concentrations of total VOCs in the workshops were 0.1-0.5 mg x m(-3), 1.5-2.5 mg x m(-3) and 20-200 mg x m(-3) for casting, cutting and painting respectively. Main compositions of VOCs in those workshops were alkanes, eneynes, aromatics, ketones, esters and ethers, totally over 20 different species. The main compositions in painting workshop were aromatics and ketones, among which the concentration of benzene was 0.02-0.34 mg x m(-3), toluene was 0.24-3.35 mg x m(-3), ethyl benzene was 0.04-1.33 mg x m(-3), p-xylene was 0.13-0.96 mg x m(-3), m-xylene was 0.02-1.18 mg x m(-3), acetone was 0.29-15.77 mg x m(-3), 2-butanone was 0.06-22.88 mg x m(-3), cyclohexene was 0.02-25.79 mg x m(-3), and methyl isobutyl ketone was 0-21.29 mg x m(-3). The VOCs emission from painting process was about 14 t x a(-1) for one single manufacturing line, and 840 t x a(-1) for the whole factory. According to the work flows and product processes, the solvent used during painting process was the main source of VOCs emission, and the exhaust gas was the main emission point.

  5. Multi-solution processes of small molecule for flexible white organic light-emitting diodes

    Energy Technology Data Exchange (ETDEWEB)

    Tsai, Yu-Sheng, E-mail: ystsai@nfu.edu.tw [Institute of Electro-optical and Materials Science, National Formosa University, Yunlin 63201, Taiwan, ROC (China); Chittawanij, Apisit; Hong, Lin-Ann; Guo, Siou-Wei [Institute of Electro-optical and Materials Science, National Formosa University, Yunlin 63201, Taiwan, ROC (China); Wang, Ching-Chiun [Department of Solid State Lighting Technology, Mechanical and Systems Research Laboratories, Industrial Technology Research Institute, Hsinchu 31040, Taiwan, ROC (China); Juang, Fuh-Shyang [Institute of Electro-optical and Materials Science, National Formosa University, Yunlin 63201, Taiwan, ROC (China); Lai, Shih-Hsiang [Department of Solid State Lighting Technology, Mechanical and Systems Research Laboratories, Industrial Technology Research Institute, Hsinchu 31040, Taiwan, ROC (China); Lin, Yang-Ching [Institute of Electro-optical and Materials Science, National Formosa University, Yunlin 63201, Taiwan, ROC (China)

    2016-04-01

    Most small molecule organic light emitting diode (SM-OLED) device structures are made in one layer using solution-based processing because the solution is usually a high dissolvent material that easily attacks the layer below it. We demonstrate a simple and reliable stamping technique for fabricating multi-solution process flexible white SM-OLEDs. The structure is anode/spin-hole injection layer/spin-emitting layer/stamping-electron transport layer/cathode. Poly(di-methyl silane) (PDMS) stamp is used for transferring electron transport layer. An intermediate ultraviolet-ozone surface treatment is introduced to temporarily modify the PDMS stamp surface. Then, the solution-based electron transport layer film can therefore be uniformly formed on top of the PDMS surface. After that the electron transport layer film on the PDMS stamp is transfer-printed onto the emitting layer with suitable heating and pressing. A solution-based processing is successfully established to efficiently fabricate flexible white SM-OLEDs. The SM-OLEDs were obtained at the current density of 20 mA/cm{sup 2}, luminance of 1062 cd/m{sup 2}, current efficiency of 5.57 cd/A, and Commission internationale de l'éclairage coordinate of (0.32, 0.35). - Highlights: • All solution-processed small molecule materials (emitting layer, electron transport layer). • Poly(di-methylsilane) (PDMS) stamp is subsequently used for stamping transfer. • The flexible white SM-OLEDs are based on solution-processes with a low-cost method.

  6. [Spectral Analysis of Dissolved Organic Matter of Tannery Wastewater in the Treatment Process].

    Science.gov (United States)

    Fan, Chun-hui; Zhang, Ying-chao; Du, Bo; Song, Juan; Huai, Cui-qian; Wang, Jia-hong

    2015-06-01

    Tannery industry is one of the major traditional industries and important wastewater sources in China. The existing research mainly focus on the quality of inlet and outlet water, rather than the purification and transformation behavior of dissolved organic matter (DOM) in the treatment process of tannery wastewater. The UV spectra and fluorescence spectroscopy were used to detect the spectral characteristics of water samples in the treatment process, and it is analyzed that the formation process and the linear relationships between total fluorescence intensity and parameters. The results showed: the UV absorbance of DOM in wastewater increased firstly and then decreased with longer wavelength, and the wave peaks were found around the wavelength of 230 nr. The values of A253 /A203 and SUVA254 increased firstly and then decreased, indicating the complex reaction process related to free substituent and aromatic rings. The fluorescence peaks appeared at the regions of λ(ex/em) = 320-350/440- 460 and λ(ex/em) = 270-300/390-420, referred as visible humic-like and visible fulvic-like fluorescence, respectively. With the treatment process of tannery wastewater, the following fluorescence phenomenon were monitored, such as the blue-shift of humic-like fluorescence peak in the hydrolytic acidification tank, the appearance of tryptophan fluorescence peak in the second biochemical pond (λ(ex/em) = 290/340), the weak fluorescence peak in the fourth biochemical pond (λ(ex/em) = 350/520) and the stabilized fluorescence characteristics in the secondary sedimentation tank and water outlet. The achievements are helpful to investigate the degradation and formation behavior of water components, and significant for the fluorescence variation analysis in the treatment system. The removal rate of total fluorescence intensity of tannery wastewater fit better the removal rate of TOC with coefficient of r 0.835 5. The UV spectra and 3D-EEMs are effective to reveal the purification

  7. Multi-solution processes of small molecule for flexible white organic light-emitting diodes

    International Nuclear Information System (INIS)

    Tsai, Yu-Sheng; Chittawanij, Apisit; Hong, Lin-Ann; Guo, Siou-Wei; Wang, Ching-Chiun; Juang, Fuh-Shyang; Lai, Shih-Hsiang; Lin, Yang-Ching

    2016-01-01

    Most small molecule organic light emitting diode (SM-OLED) device structures are made in one layer using solution-based processing because the solution is usually a high dissolvent material that easily attacks the layer below it. We demonstrate a simple and reliable stamping technique for fabricating multi-solution process flexible white SM-OLEDs. The structure is anode/spin-hole injection layer/spin-emitting layer/stamping-electron transport layer/cathode. Poly(di-methyl silane) (PDMS) stamp is used for transferring electron transport layer. An intermediate ultraviolet-ozone surface treatment is introduced to temporarily modify the PDMS stamp surface. Then, the solution-based electron transport layer film can therefore be uniformly formed on top of the PDMS surface. After that the electron transport layer film on the PDMS stamp is transfer-printed onto the emitting layer with suitable heating and pressing. A solution-based processing is successfully established to efficiently fabricate flexible white SM-OLEDs. The SM-OLEDs were obtained at the current density of 20 mA/cm"2, luminance of 1062 cd/m"2, current efficiency of 5.57 cd/A, and Commission internationale de l'éclairage coordinate of (0.32, 0.35). - Highlights: • All solution-processed small molecule materials (emitting layer, electron transport layer). • Poly(di-methylsilane) (PDMS) stamp is subsequently used for stamping transfer. • The flexible white SM-OLEDs are based on solution-processes with a low-cost method.

  8. Surface interactions between nanoscale iron and organic material: Potential uses in water treatment process units

    Science.gov (United States)

    Storms, Max

    Membrane systems are among the primary emergent technologies in water treatment process units due to their ease of use, small physical footprint, and high physical rejection. Membrane fouling, the phenomena by which membranes become clogged or generally soiled, is an inhibitor to optimal efficiency in membrane systems. Novel, composite, and modified surface materials must be investigated to determine their efficacy in improving fouling behavior. Ceramic membranes derived from iron oxide nanoparticles called ferroxanes were coated with a superhydrophillic, zwitterionic polymer called poly (sulfobetaine methacrylate) (polySBMA) to form a composite ceramic-polymeric membrane. Membrane samples with and without polySBMA coating were subjected to fouling with a bovine serum albumin solution and fouling was observed by measuring permeate flux at 10 mL intervals. Loss of polySBMA was measured using total organic carbon analysis, and membrane samples were characterized using x-ray diffraction, scanning electron microscopy, and optical profilometry. The coated membrane samples decreased initial fouling rate by 27% and secondary fouling rate by 24%. Similarly, they displayed a 30% decrease in irreversible fouling during the initial fouling stage, and a 27% decrease in irreversible fouling in the secondary fouling stage; however, retention of polySBMA sufficient for improved performance was not conclusive. The addition of chemical disinfectants into drinking water treatment processes results in the formation of compounds called disinfection by-products (DBPs). The formation of DBPs occurs when common chemical disinfectants (i.e. chlorine) react with organic material. The harmful effects of DBP exposure require that they be monitored and controlled for public safety. This work investigated the ability of nanostructured hematite derived from ferroxane nanoparticles to remove organic precursors to DBPs in the form of humic acid via adsorption processes. The results show that p

  9. DEMONSTRATION OF THE STRATEGY FORMATION PROCESS: A CASE STUDY IN A INNOVATIVE ORGANIZATION

    Directory of Open Access Journals (Sweden)

    Daniel Teodoro Gomes

    2012-05-01

    Full Text Available This paper presents a study of strategy formation process with the following starting question: "How the strategy is shaped in an innovative company and how the factors manifesting in the process?". The research builds on a case study of a company considered innovative leader in its industry and a pioneer in providing various services in the area of mobile phone in Brazil. Data collection was through interviews semi-structured with directors and managers involved in strategy formation, supplemented by documents and direct observation. Data analysis is based on the techniques of discourse analysis, from the persuasion strategies suggested by Linhares and Faria (1993. The company's strategy studied can be defined as an entrepreneurial vision, focused on growth supported by a process of diversification of product lines from a new direction composed of three elements: (i componentization; (ii segmentation by products chain and; (iii external to finance leverage in order to resumption of innovative projects. It was concluded that the company's strategy focused on these three factors, supported by a deliberate vision of the future, conditions its historical trajectory type standard cultural, its core values, which acts as a motivator and guide for members of the organization decisions and actions.

  10. How "mere" is the mere ownership effect in memory? Evidence for semantic organization processes.

    Science.gov (United States)

    Englert, Julia; Wentura, Dirk

    2016-11-01

    Memory is better for items arbitrarily assigned to the self than for items assigned to another person (mere ownership effect, MOE). In a series of six experiments, we investigated the role of semantic processes for the MOE. Following successful replication, we investigated whether the MOE was contingent upon semantic processing: For meaningless stimuli, there was no MOE. Testing for a potential role of semantic elaboration using meaningful stimuli in an encoding task without verbal labels, we found evidence of spontaneous semantic processing irrespective of self- or other-assignment. When semantic organization was manipulated, the MOE vanished if a semantic classification task was added to the self/other assignment but persisted for a perceptual classification task. Furthermore, we found greater clustering of self-assigned than of other-assigned items in free recall. Taken together, these results suggest that the MOE could be based on the organizational principle of a "me" versus "not-me" categorization. Copyright © 2016 Elsevier Inc. All rights reserved.

  11. Efficient green phosphorescent tandem organic light emitting diodes with solution processable mixed hosts charge generating layer

    Energy Technology Data Exchange (ETDEWEB)

    Talik, N.A.; Yeoh, K.H.; Ng, C.Y.B [Low Dimensional Research Center, Department of Physics, University Malaya, 50603 Kuala Lumpur (Malaysia); ItraMAS Corporation. Sdn. Bhd., 542A-B Mukim 1, Lorong Perusahaan Baru 2, Kawasan Perindustrian, Perai 13600, Penang (Malaysia); Yap, B.K. [Center of Microelectronic and Nanotechnology Engineering (CeMNE), College of Engineering, Universiti Tenaga Nasional, Jln. Uniten-Ikram, 4300 Kajang, Selangor (Malaysia); Woon, K.L., E-mail: ph7klw76@um.edu.my [Low Dimensional Research Center, Department of Physics, University Malaya, 50603 Kuala Lumpur (Malaysia)

    2014-10-15

    A novel solution processable charge generating layer (CGL) that consists of 1,4,5,8,9,11-hexaazatriphenylene hexacarbonitrile (HATCN{sub 6})/Poly(N-vinylcarbazole) (PVK): 1,1-bis-(4-bis(4-tolyl)-aminophenyl) cyclohexene (TAPC) for a tandem green phosphorescent organic light emitting diode (PHOLED) is demonstrated. The use of orthogonal solvent to dissolve HATCN{sub 6} and PVK:TAPC is the key to overcome the interface erosion problem for the solution processed CGL. The current efficiency of the 2 wt% TAPC mixed with PVK is the highest at 24.2 cd/A, which is more than three-folds higher than that of the single device at 1000 cd/m{sup 2}. - Highlights: • A solution processable tandem OLED is built using a novel charge generating layer. • HATCN{sub 6} and PVK:TAPC are shown to be effective charge generating layers. • The turn on voltages for tandem devices are almost similar to single unit. • 2 wt% TAPC blended with PVK exhibits three-folds increase in efficiency.

  12. Application of the Theory of Self-Organized Criticality to the Investigation of Historical Processes

    Directory of Open Access Journals (Sweden)

    Dmitry S. Zhukov

    2016-12-01

    Full Text Available The article demonstrates heuristic possibilities of the theory of self-organized criticality (SOC in the investigation of historical processes. Key SOC concepts and ideas are explained. Specifically, tools that can be used for identifying pink noise, an attribute of a critical state, are described. The results of spectral analyses of historical demographic data (i.e., birth and death rates in Russian settlements in the 19th and 20th centuries and historical market data (i.e., grain prices in regions of Russia in the 18th, 19th, and early 20th centuries are presented. It was found that noise color in the data series differed substantially across different periods. Based on these observations, the assumption that a change in noise color can serve as an indicator of changes in historical processes was made. In some cases, this indicator can enable one to establish the time, speed, and direction of state changes in historical processes. Pink noise was discovered in the examined birth and death rate dynamics, as well as in the dynamics of prices across periods. The described methods have the potential to be used beyond the limits of the presently considered historical subjects, including in investigations of different types of social transformation.

  13. Asymmetric neighborhood functions accelerate ordering process of self-organizing maps

    International Nuclear Information System (INIS)

    Ota, Kaiichiro; Aoki, Takaaki; Kurata, Koji; Aoyagi, Toshio

    2011-01-01

    A self-organizing map (SOM) algorithm can generate a topographic map from a high-dimensional stimulus space to a low-dimensional array of units. Because a topographic map preserves neighborhood relationships between the stimuli, the SOM can be applied to certain types of information processing such as data visualization. During the learning process, however, topological defects frequently emerge in the map. The presence of defects tends to drastically slow down the formation of a globally ordered topographic map. To remove such topological defects, it has been reported that an asymmetric neighborhood function is effective, but only in the simple case of mapping one-dimensional stimuli to a chain of units. In this paper, we demonstrate that even when high-dimensional stimuli are used, the asymmetric neighborhood function is effective for both artificial and real-world data. Our results suggest that applying the asymmetric neighborhood function to the SOM algorithm improves the reliability of the algorithm. In addition, it enables processing of complicated, high-dimensional data by using this algorithm.

  14. Tips pentacene crystal alignment for improving performance of solution processed organic thin film transistors

    Science.gov (United States)

    He, Zhengran

    A newly-developed p-type organic semiconductor 6,13-bis (triisopropylsilylethynyl) pentacene (TIPS pentacene) demonstrates various advantages such as high mobility, air stability and solution processibility, but at the same time its application is restricted by major issues, such as crystal misorientation and performance variation of organic thin-film transistors (OTFTs). This dissertation demonstrates several different approaches to address these issues. As a result, both crystal orientation and areal coverage can be effectively improved, leading to an enhancement of average mobility and performance consistency of OTFTs. Chapter 1 presents an introduction and background of this dissertation. Chapter 2 explores the usage of inorganic silica nanoparticles to manipulate the morphology of TIPS pentacene thin films and the performance of solution-processed organic OTFTs. The resultant drop-cast films yield improved morphological uniformity at ~10% SiO2 loading, which also leads to a 3-fold increase in average mobility and nearly 4-times reduction in the ratio of standard deviation of mobility (μStdev) to average mobility (μAvg). The experimental results suggest that the SiO2 nanoparticles mostly aggregate at TIPS pentacene grain boundaries, and that 10% nanoparticle concentration effectively reduces the undesirable crystal misorientation without considerably compromising TIPS pentacene crystallinity. Chapter 3 discusses the utilization of air flow to effectively reduce the TIPS pentacene crystal anisotropy and enhance performance consistency in OTFTs. Under air-flow navigation (AFN), TIPS pentacene forms thin films with improved crystal orientation and increased areal coverage, which subsequently lead to a four-fold increase of average hole mobility and one order of magnitude enhancement in performance consistency. Chapter 4 investigates the critical roles of lateral and vertical phase separation in the performance of the next-generation organic and hybrid electronic

  15. National Study of Word Processing Installations in Selected Business Organizations. A Report on the National Word Processing Research Study of Delta Pi Epsilon.

    Science.gov (United States)

    Scriven, Jolene D.; And Others

    A study was conducted (1) to determine current practices in word processing installations in selected organizations throughout the United States, and (2) to ascertain anticipated future developments in word processing as well as to provide recommendations for educational institutions that prepare workers for business offices. Seven interview…

  16. The Role of Interstate Policy Organizations in State Higher Education Policy Processes: Perceptions of Policymakers and Policy Shapers

    Science.gov (United States)

    Michelau, Demaree K.

    2010-01-01

    Political science offers rich explanations for how different types of organizations that are focused on public policy decisions (e.g., boundary organizations, interest groups, policy networks (or communities), and think tanks) influence public policy processes (Cash, Clark, Alcock, Dickson, Eckley, Guston, Jager, and Mitchell 2003; Guston 2001;…

  17. The Relationship between Environmental Turbulence, Management Support, Organizational Collaboration, Information Technology Solution Realization, and Process Performance, in Healthcare Provider Organizations

    Science.gov (United States)

    Muglia, Victor O.

    2010-01-01

    The Problem: The purpose of this study was to investigate relationships between environmental turbulence, management support, organizational collaboration, information technology solution realization, and process performance in healthcare provider organizations. Method: A descriptive/correlational study of Hospital medical services process…

  18. Electronic Processes at Organic−Organic Interfaces: Insight from Modeling and Implications for Opto-electronic Devices †

    KAUST Repository

    Beljonne, David; Cornil, Jérôme; Muccioli, Luca; Zannoni, Claudio; Brédas, Jean-Luc; Castet, Frédéric

    2011-01-01

    We report on the recent progress achieved in modeling the electronic processes that take place at interfaces between π-conjugated materials in organic opto-electronic devices. First, we provide a critical overview of the current computational

  19. [Dynamics of unprotected soil organic carbon with the restoration process of Pinus massoniana plantation in red soil erosion area].

    Science.gov (United States)

    Lü, Mao-Kui; Xie, Jin-Sheng; Zhou, Yan-Xiang; Zeng, Hong-Da; Jiang, Jun; Chen, Xi-Xiang; Xu, Chao; Chen, Tan; Fu, Lin-Chi

    2014-01-01

    By the method of spatiotemporal substitution and taking the bare land and secondary forest as the control, we measured light fraction and particulate organic carbon in the topsoil under the Pinus massoniana woodlands of different ages with similar management histories in a red soil erosion area, to determine their dynamics and evaluate the conversion processes from unprotected to protected organic carbon. The results showed that the content and storage of soil organic carbon increased significantly along with ages in the process of vegetation restoration (P organic carbon content and distribution proportion to the total soil organic carbon increased significantly (P organic carbon mostly accumulated in the form of unprotected soil organic carbon during the initial restoration period, and reached a stable level after long-term vegetation restoration. Positive correlations were found between restoration years and the rate constant for C transferring from the unprotected to the protected soil pool (k) in 0-10 cm and 10-20 cm soil layers, which demonstrated that the unprotected soil organic carbon gradually transferred to the protected soil organic carbon in the process of vegetation restoration.

  20. A Comparison of the Request Process and Outcomes in Adult and Pediatric Organ Donation

    Science.gov (United States)

    Siminoff, Laura A.; Molisani, Anthony J.

    2015-01-01

    BACKGROUND AND OBJECTIVES: Although existing studies suggest that factors affecting families’ decisions regarding pediatric organ donation mirror those for adult patients, health professionals working in this area maintain that pediatric and adult decision-makers differ in significant ways. This study compared the request process, experiences, and authorization decisions between family decision-makers (FDMs) of adult and pediatric donors and nondonors. METHODS: Perceptions of the donation request were collected via telephone interviews with 1601 FDMs approached by staff from 9 US organ procurement organizations (OPOs). Authorization regarding donation (ie, authorized/refused) was obtained from FDM reports and verified by using OPO records. Tests of association were used to estimate differences between FDMs of adult and pediatric patients. A logistic regression analysis was conducted to identify variables predicting FDM authorization. RESULTS: FDMs of children were significantly more likely to authorize donation than were FDMs of adults (89.7% vs 83.2%; χ2 = 6.2, P = .01). Differences were found between pediatric and adult families’ initial feelings toward donation, donation-related topics discussed, communication behaviors and techniques used, perceptions of the request, and receipt and preference of grief information. The likelihood of FDM authorization increased with the number of topics discussed and communication skills employed during requests. Authorization was not predicted by patient age (ie, adult versus pediatric). CONCLUSIONS: FDMs of children are willing to donate and experience no more psychological distress from the request for donation than do FDMs of adults. Communication emerged as a critical factor of family authorization, reinforcing its importance in requests for donation. PMID:26034251

  1. Persistent organic pollutants (POPs) in the conventional activated sludge treatment process: fate and mass balance

    International Nuclear Information System (INIS)

    Katsoyiannis, Athanasios; Samara, Constantini

    2005-01-01

    The fate and the mass balance of persistent organic pollutants (POPs) during the conventional activated sludge treatment process were investigated in the wastewater treatment plant of the city of Thessaloniki, northern Greece. The POPs of interest were 7 polychlorinated biphenyls and 19 organochlorine pesticides. Target compounds were determined at six different points across the treatment system: the influent, the effluent of the primary sedimentation tank, the effluent of the secondary sedimentation tank, the primary sludge, the activated sludge from the recirculation stream, and the digested/dewatered sludge. The distribution of POPs between the dissolved and the adsorbed phases of wastewater and sludge was investigated. A good linear relationship between the distribution coefficients, K d , and the octanol-water partition coefficients, K ow , of the solutes was observed only in raw wastewater, suggesting that other factors affect the phase distribution of organic compounds in treated wastewater. For all POPs, a significant increase in partitioning with a decreasing solids concentration was observed, revealing an effect from non-settling microparticles remaining in the 'dissolved' phase during the separation procedure. A good linear relationship was also revealed between logK d and the dissolved organic carbon (DOC) content of wastewater, suggesting that DOC favors the advective transport of POPs in the dissolved phase. Almost all POPs showed good mass balance agreements at both the primary and the secondary treatment. The losses observed for some species could be attributed to biodegradation/biotransformation rather than volatilization. The relative distribution between the treated effluent and the waste sludge streams varied largely among different compounds, with p-p'-DDE being highly accumulated in the waste sludge (98%) but almost 60% of α-HCH remaining in the treated effluent

  2. [Spectral characteristics of dissolved organic matter released during the metabolic process of small medusa].

    Science.gov (United States)

    Guo, Dong-Hui; Yi, Yue-Yuan; Zhao, Lei; Guo, Wei-Dong

    2012-06-01

    The metabolic processes of jellyfish can produce dissolved organic matter (DOM) which will influence the functioning of the aquatic ecosystems, yet the optical properties of DOM released by jellyfish are unknown. Here we report the absorption and fluorescence properties of DOM released by a medusa species Black fordia virginica during a 24 h incubation experiment. Compared with the control group, an obvious increase in the concentrations of dissolved organic carbon (DOC), absorption coefficient (a280) and total dissolved nitrogen (TDN) was observed in incubation group. This clearly demonstrated the release of DOM, chromophoric DOM (CDOM) and dissolved nutrients by B. virginica which feed on enough of Artemia sp. before the experiment. The increase in spectral slope ratio (SR) and decrease in humification index (HIX) indicated that the released DOM was less-humified and had relatively lower molecular weight. Parallel factor analysis (PARAFAC) decomposed the fluorescence matrices of DOM into three humic-like components (C1-C3) and one protein-like component (C4). The Fmax of two components (C2: 400 nm showed little changes. Thus, we suggested a zooplankton index (ZIX) to trace and characterize the DOM excreted by metabolic activity of zooplankton, which is calculated as the ratio of the sum of Fmax of all fluorescence components with the emission wavelength 400 nm.

  3. Heterogeneous nucleation promotes carrier transport in solution-processed organic field-effect transistors

    KAUST Repository

    Li, Ruipeng

    2012-09-04

    A new way to investigate and control the growth of solution-cast thin films is presented. The combination of in situ quartz crystal microbalance measurements with dissipation capabilities (QCM-D) and in situ grazing-incidence wide-angle X-ray scattering (GIWAXS) in an environmental chamber provides unique quantitative insights into the time-evolution of the concentration of the solution, the onset of nucleation, and the mode of growth of the organic semiconductor under varied drying conditions. It is demonstrated that careful control over the kinetics of solution drying enhances carrier transport significantly by promoting phase transformation predominantly via heterogeneous nucleation and sustained surface growth of a highly lamellar structure at the solid-liquid interface at the expense of homogeneous nucleation. A new way to investigate and control the growth of drop-cast thin films is presented. The solution-processing of small-molecule thin films of TIPS-pentacene is investigated using time-resolved techniques to reveal the mechanisms of nucleation and growth leading to solid film formation. By tuning the drying speed of the solution, the balance between surface and bulk growth modes is altered, thereby controlling the lamellar formation and tuning the carrier mobility in organic field-effect transistors Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Evaluation of respiratory parameters in minimally processed lettuce grown under organic or conventional system

    Directory of Open Access Journals (Sweden)

    Júlio César Mello

    2010-12-01

    Full Text Available The increased preference for minimally processed vegetables has been attributed to the health benefits associated with fresh produce and the demand for ready-to-eat salads. In this paper, lettuce (Lactuca sativa L. was evaluated for the effects of different cropping systems on the respiratory properties. Lettuce was packaged in low density polyethylene bags and stored in a refrigerator at 4 ºC. The concentration of carbon dioxide and oxygen inside the package was monitored during the storage at zero, three, six, eight, ten and twelve days by gas chromatography. Dry matter variation was measured gravimetrically up to day fourteen of storage. Values of respiratory rate for conventional lettuce increased from day 1 to 3 and remained low, while respiratory rate of the organic lettuce increased three-fold up to day 8, stabilizing at a high level. Variation in dry matter during storage also resulted from differences between the two cultivation systems. The highest content of dry matter was achieved by organic lettuce.

  5. Ambipolar Small-Molecule:Polymer Blend Semiconductors for Solution-Processable Organic Field-Effect Transistors.

    Science.gov (United States)

    Kang, Minji; Hwang, Hansu; Park, Won-Tae; Khim, Dongyoon; Yeo, Jun-Seok; Kim, Yunseul; Kim, Yeon-Ju; Noh, Yong-Young; Kim, Dong-Yu

    2017-01-25

    We report on the fabrication of an organic thin-film semiconductor formed using a blend solution of soluble ambipolar small molecules and an insulating polymer binder that exhibits vertical phase separation and uniform film formation. The semiconductor thin films are produced in a single step from a mixture containing a small molecular semiconductor, namely, quinoidal biselenophene (QBS), and a binder polymer, namely, poly(2-vinylnaphthalene) (PVN). Organic field-effect transistors (OFETs) based on QBS/PVN blend semiconductor are then assembled using top-gate/bottom-contact device configuration, which achieve almost four times higher mobility than the neat QBS semiconductor. Depth profile via secondary ion mass spectrometry and atomic force microscopy images indicate that the QBS domains in the films made from the blend are evenly distributed with a smooth morphology at the bottom of the PVN layer. Bias stress test and variable-temperature measurements on QBS-based OFETs reveal that the QBS/PVN blend semiconductor remarkably reduces the number of trap sites at the gate dielectric/semiconductor interface and the activation energy in the transistor channel. This work provides a one-step solution processing technique, which makes use of soluble ambipolar small molecules to form a thin-film semiconductor for application in high-performance OFETs.

  6. The effect of mixing ratio variation of sludge and organic solid waste on biodrying process

    Science.gov (United States)

    Nasution, A. C.; Kristanto, G. A.

    2018-01-01

    In this study, organic waste was co-biodried with sludge cake to determine which mixing ratio gave the best result. The organic waste was consisted of dried leaves and green leaves, while the sludge cake was obtained from a waste water treatment plant in Bekasi. The experiment was performed on 3 lab-scale reactors with same specifications. After 21 days of experiment, it was found that the reactor with the lowest mixing fraction of sludge (5:1) has the best temperature profile and highest moisture content depletion compared with others. Initial moisture content and initial volatile solid content of this reactor’s feedstock was 52.25% and 82.4% respectively. The airflow rate was 10 lpm. After biodrying was done, the final moisture content of the feedstock from Reactor C was 22.0% and the final volatile solid content was 75.9%.The final calorific value after biodrying process was 3179,28kcal/kg.

  7. Multiscale grooved titanium processed with femtosecond laser influences mesenchymal stem cell morphology, adhesion, and matrix organization.

    Science.gov (United States)

    Dumas, Virginie; Rattner, Aline; Vico, Laurence; Audouard, Eric; Dumas, Jean Claude; Naisson, Pierre; Bertrand, Philippe

    2012-11-01

    The femtosecond laser processing enabled the structuring of six types of surfaces on titanium-6aluminium-4vanadium (Ti-6Al-4V) plates. The obtained hierarchical features consisted of a combination of microgrooves and oriented nanostructures. By adjusting beam properties such as laser polarization, the width of the microgrooves (20 or 60 μm) and the orientation of the nanostructures (parallel or perpendicular to the microgrooves) can be precisely controlled. Mesenchymal stem cells (MSCs) grown on these structured surfaces produced cytoplasmic extensions with focal contacts, while on the smooth titanium, the cells were found to be well spread and without any focal contact 12 h postseeding. The 600-nm wide nanostructures on their own were sufficient to orient the MSCs. For the multiscale structured areas, when the orientation of the nanostructures was orthogonal in relation to the microgrooves, there was an important decrease in or even a loss of cell alignment signifying that cells were sensitive to the directional nanostructures in the microgrooves. At 7 days, cell proliferation was not affected but the direction of nanostructures controlled the matrix organization. The ultrafast laser, as a new method for producing micro-nanohybrid surfaces, is a promising approach to promote desired tissue organization for tissue engineering. Copyright © 2012 Wiley Periodicals, Inc.

  8. Knowledge-Centric Technical Support Organization (TSO) Using Process Oriented Knowledge Management Approach

    International Nuclear Information System (INIS)

    Mohamad Safuan Sulaiman; Siti Nurbahyah Hamdan; Mohd Dzul Aiman Aslan

    2014-01-01

    In the United States of America, Process Oriented Knowledge Management (POKM) Model has been successfully implemented in most of Nuclear Power Plants. This approach has been introduced in Nuclear Knowledge Management program by the IAEA since 2011. Malaysia has involved in the IAEA Coordinated Research Project (CRP) focusing the approach started in 2011. The main objective for Malaysian participation of this project is to support readiness in terms of nuclear technical knowledge by Technical Support Organization (TSO) for Nuclear Power Program. This project has focused on several nuclear technical areas which consist of Public Information (PI), Radiological Impact Assessment (RIA), Nuclear Reactor Technology (NRT), Plant and Prototype Development (PDC) and nuclear knowledge management. This paper articulates the detail POKM approach and project experience in implementing the approach at organizational level. (author)

  9. Desulfurization of organic sulfur from lignite by an electron transfer process

    Energy Technology Data Exchange (ETDEWEB)

    Demirbas, A. [Selcuk University, Konya (Turkey). Dept. for Chemical Engineering

    2006-10-15

    This study is an attempt to desulfurize organic sulfur from lignite samples with ferrocyanide ion as the electron transferring agent. Effect of temperature, particle size and concentration of ferrocyanide ion on desulfurization from the lignite samples has been investigated. The desulfurization process has been found to be continuous and gradually increases with increase of temperature from 298 to 368 K. The particle size has no significant impact on sulfur removal from the lignite samples. Particle size has no profound impact on the amount of sulfur removal. The desulfurization reaction has been found to be dependent on the concentration of potassium ferrocyanide. Gradual increase in the concentration of potassium ferrocyanide raised the magnitude of desulfurization, but at a higher concentration, the variation is not significant.

  10. Tracking transformation processes of organic micropollutants in aquatic environments using multi-element isotope fractionation analysis

    International Nuclear Information System (INIS)

    Hofstetter, Thomas B.; Bolotin, Jakov; Skarpeli-Liati, Marita; Wijker, Reto; Kurt, Zohre; Nishino, Shirley F.; Spain, Jim C.

    2011-01-01

    The quantitative description of enzymatic or abiotic transformations of man-made organic micropollutants in rivers, lakes, and groundwaters is one of the major challenges associated with the risk assessment of water resource contamination. Compound-specific isotope analysis enables one to identify (bio)degradation pathways based on changes in the contaminants' stable isotope ratios even if multiple reactive and non-reactive processes cause concentrations to decrease. Here, we investigated how the magnitude and variability of isotope fractionation in some priority pollutants is determined by the kinetics and mechanisms of important enzymatic and abiotic redox reactions. For nitroaromatic compounds and substituted anilines, we illustrate that competing transformation pathways can be assessed via trends of N and C isotope signatures.

  11. Processing of Polypropylene-Organic Montmorillonite Nanocomposite by Equal Channel Multiangular Extrusion

    Directory of Open Access Journals (Sweden)

    V. A. Beloshenko

    2016-01-01

    Full Text Available By the example of polypropylene-organic montmorillonite composite (PP-OMMT, the abilities of the method of equal channel multiangular extrusion have been studied with respect to the modification of the structure and the properties of polymeric nanocomposites. With using X-ray structure analysis, TEM, DSC, and dilatometry, it has been demonstrated that this kind of processing provides an additional intercalation of the polymer into OMMT tactoids with the succeeding exfoliation and facilitates an increase in the aspect ratio, the degree of platelet orientation, the crystalline lamellar thickness, and a decrease in the dispersion of the crystallite thickness, as well as the formation of biaxial orientation of the OMMT and PP crystals. The observed structure rearrangements determine enhanced microhardness, ductility, and the heat distortion temperature of the PP-OMMT composite.

  12. Thermally induced processes in mixtures of aluminum with organic acids after plastic deformations under high pressure

    Science.gov (United States)

    Zhorin, V. A.; Kiselev, M. R.; Roldugin, V. I.

    2017-11-01

    DSC is used to measure the thermal effects of processes in mixtures of solid organic dibasic acids with powdered aluminum, subjected to plastic deformation under pressures in the range of 0.5-4.0 GPa using an anvil-type high-pressure setup. Analysis of thermograms obtained for the samples after plastic deformation suggests a correlation between the exothermal peaks observed around the temperatures of degradation of the acids and the thermally induced chemical reactions between products of acid degradation and freshly formed surfaces of aluminum particles. The release of heat in the mixtures begins at 30-40°C. The thermal effects in the mixtures of different acids change according to the order of acid reactivity in solutions. The extreme baric dependences of enthalpies of thermal effects are associated with the rearrangement of the electron subsystem of aluminum upon plastic deformation at high pressures.

  13. Y-12 Development Organization technical progress report: Part 3 -- Metal processing, period ending March 1, 1994

    International Nuclear Information System (INIS)

    Northcutt, W.G. Jr.

    1994-01-01

    As part of the effort to downsize its uranium processing facilities, the Y-12 Plant has supported an investigation to identify extraction solvents that would both work efficiently in centrifugal contactors and be disposed of easily. Various organic ethers, hydroxy ethers, ether ketones, acids, amides, and diketones were studied for their ability to extract uranyl nitrate from aqueous solutions. Although many of these solvents were obtained commercially, others had to be synthesized in-house. The authors found a large range of extraction coefficients for these solvents. Because of steric hindrance or some other factor, certain ethers performed poorly. On the other hand, various mono- and diethers of tetrahydrofurfuryl alcohol exhibited excellent extraction and stripping coefficients for uranyl nitrate, justifying purchase of a pilot plant batch of one of this family of solvents. Likewise, the authors determined the extraction coefficient for one of the two amides synthesized in-house to be quite high

  14. A process-based emission model of volatile organic compounds from silage sources on farms

    DEFF Research Database (Denmark)

    Bonifacio, H. F.; Rotz, C. A.; Hafner, S. D.

    2017-01-01

    Silage on dairy farms can emit large amounts of volatile organic compounds (VOCs), a precursor in the formation of tropospheric ozone. Because of the challenges associated with direct measurements, process-based modeling is another approach for estimating emissions of air pollutants from sources...... was evaluated using ethanol and methanol emissions measured from conventional silage piles (CSP), silage bags (SB), total mixed rations (TMR), and loose corn silage (LCS) at a commercial dairy farm in central California. With transport coefficients for ethanol refined using experimental data from our previous......% if feeds were delivered as four feedings per day rather than as one. Reducing the exposed face of storage can also be useful. Simulated use of silage bags resulted in 90% and 18% reductions in emissions from the storage face and whole farm, respectively....

  15. Improving organic tandem solar cells based on water-processed nanoparticles by quantitative 3D nanoimaging

    DEFF Research Database (Denmark)

    Pedersen, Emil Bøje Lind; Angmo, Dechan; Dam, Henrik Friis

    2015-01-01

    particle active layer. We extract the layered morphology with structural and density information including the porosity present in the various layers and the silver electrode with high resolution in 3D. The Landfester particle layer is found to have an undesired morphology with negatively correlated top......Organic solar cells have great potential for upscaling due to roll-to-roll processing and a low energy payback time, making them an attractive sustainable energy source for the future. Active layers coated with water-dispersible Landfester particles enable greater control of the layer formation...... specifically reveals the need to improve the coatability and layer formation of Landfester nanoparticles, thus allowing improved solar cells to be produced....

  16. OLED Fundamentals: Materials, Devices, and Processing of Organic Light-Emitting Diodes

    Energy Technology Data Exchange (ETDEWEB)

    Blochwitz-Nimoth, Jan; Bhandari, Abhinav; Boesch, Damien; Fincher, Curtis R.; Gaspar, Daniel J.; Gotthold, David W.; Greiner, Mark T.; Kido, Junji; Kondakov, Denis; Korotkov, Roman; Krylova, Valentina A.; Loeser, Falk; Lu, Min-Hao; Lu, Zheng-Hong; Lussem, Bjorn; Moro, Lorenza; Padmaperuma, Asanga B.; Polikarpov, Evgueni; Rostovtsev, Vsevolod V.; Sasabe, Hisahiro; Silverman, Gary; Thompson, Mark E.; Tietze, Max; Tyan, Yuan-Sheng; Weaver, Michael; Xin , Xu; Zeng, Xianghui

    2015-05-26

    -efficiency OLED demonstrated in 1987. Thus, we expect to see exciting advances in the science, technology and commercialization in the coming years. We hope that this book helps to advance the field in some small way. Contributors to this monograph are experts from top academic institutions, industry and national laboratories who provide comprehensive and up-to-date coverage of the rapidly evolving field of OLEDs. Furthermore, this monograph collects in one place, for the first time, key topics across the field of OLEDs, from fundamental chemistry and physics, to practical materials science and engineering topics, to aspects of design and manufacturing. The monograph synthesizes and puts into context information scattered throughout the literature for easy review in one book. The scope of the monograph reflects the necessity to focus on new technological challenges brought about by the transition to manufacturing. In the Section 1, all materials of construction of the OLED device are covered, from substrate to encapsulation. In Section 2, for the first time, additional challenges in devices and processing are addressed. This book is geared towards a broad audience, including materials scientists, device physicists, synthetic chemists and electrical engineers. Furthermore, this book makes a great introduction to scientists in industry and academia, as well as graduate students interested in applied aspects of photophysics and electrochemistry in organic thin films. This book is a comprehensive source for OLED R&D professionals from all backgrounds and institutions.

  17. #RecruitmentSocialMedia : How Swedish organizations can utilize the beneficial outcomes of using social media in the recruitment process

    OpenAIRE

    Chan, Eddie; Kjellberg, Annie

    2017-01-01

    Due to changes in the labour market, organizations need to adjust and change their attitude towards the recruitment process. The traditional way of recruiting will eventually disappear and the use of social media will play an important part in recruiting. The recruitment process is a set of actions created by the organization and consists of: Recruitment Objectives, Strategy Development, Recruitment Activities, Intervening Job Applicant Variables and Recruitment Results. The use of social med...

  18. Effect of soil organic matter on antimony bioavailability after the remediation process.

    Science.gov (United States)

    Nakamaru, Yasuo Mitsui; Martín Peinado, Francisco José

    2017-09-01

    We evaluated the long-term (18 year) and short-term (4 weeks) changes of Sb in contaminated soil with SOM increase under remediation process. In the Aznalcóllar mine accident (1998) contaminated area, the remediation measurement implemented the Guadiamar Green Corridor, where residual pollution is still detected. Soils of the re-vegetated area (O2) with high pH and high SOM content, moderately re-vegetated area (O1) and unvegetated area (C) were sampled. Soil pH, CEC, SOM amount and soil Sb forms were evaluated. Soil Sb was measured as total, soluble, exchangeable, EDTA extractable, acid oxalate extractable, and pyro-phosphate extractable fractions. Further, the short-term effect of artificial organic matter addition was also evaluated with incubation study by adding compost to the sampled soil from C, O1 and O2 areas. After 4 weeks of incubation, soil chemical properties and Sb forms were evaluated. In re-vegetated area (O2), soil total Sb was two times lower than in unvegetated area (C); however, soluble, exchangeable, and EDTA extractable Sb were 2-8 times higher. The mobile/bioavailable Sb increase was also observed after 4 weeks of incubation with the addition of compost. Soluble, exchangeable, and EDTA extractable Sb was increased 2-4 times by compost addition. By the linear regression analysis, the significantly related factors for soluble, exchangeable, and EDTA extractable Sb values were pH, CEC, and SOM, respectively. Soluble Sb increase was mainly related to pH rise. Exchangeable Sb should be bound by SOM-metal complex and increased with CEC. EDTA extractable fraction should be increased with increase of SOM as SOM-Fe associated Sb complex. From these results, it was shown that increase of SOM under natural conditions or application of organic amendment under remediation process should increase availability of Sb to plants. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. The effect of microbial activity and adsorption processes on groundwater dissolved organic carbon character and concentration

    Science.gov (United States)

    Meredith, K.; McDonough, L.; Oudone, P.; Rutlidge, H.; O'Carroll, D. M.; Andersen, M. S.; Baker, A.

    2017-12-01

    Balancing the terrestrial global carbon budget has proven to be a significant challenge. Whilst the movement of carbon in the atmosphere, rivers and oceans has been extensively studied, the potential for groundwater to act as a carbon source or sink through both microbial activity and sorption to and from mineral surfaces, is poorly understood. To investigate the biodegradable component of groundwater dissolved organic carbon (DOC), groundwater samples were collected from multiple coastal and inland sites. Water quality parameters such as pH, electrical conductivity, temperature, dissolved oxygen were measured in the field. Samples were analysed and characterised for their biodegradable DOC content using spectrofluorometric and Liquid Chromatography-Organic Carbon Detection (LC-OCD) techniques at set intervals within a 28 day period. Further to this, we performed laboratory sorption experiments on our groundwater samples using different minerals to examine the effect of adsorption processes on DOC character and concentration. Calcium carbonate, quartz and iron coated quartz were heated to 400ºC to remove potential carbon contamination, and then added at various known masses (0 mg to 10 g) to 50 mL of groundwater. Samples were then rotated for two hours, filtered at 0.2 μm and analysed by LC-OCD. This research forms part of an ongoing project which will assist in identifying the factors affecting the mobilisation, transport and removal of DOC in uncontaminated groundwater. By quantifying the relative importance of these processes, we can then determine whether the groundwater is a carbon source or sink. Importantly, this information will help guide policy and identify the need to include groundwater resources as part of the carbon economy.

  20. Biochemistry Oxidation Process for Treatment the Simulation of Organic Liquid Radioactive Waste

    International Nuclear Information System (INIS)

    Gunandjar; Zainus Salimin; Sugeng Purnomo; Ratiko

    2010-01-01

    The nuclear industry activities generate the organic liquid wastes such as detergent waste from laundry, solvent waste of 30% TBP (tri-n-butyl phosphate) in kerosene from purification or recovery of uranium from rejection of nuclear fuel element fabrication, and solvent waste containing D 2 EHPA (di-2-ethyl hexyl phosphoric acid) and TOPO (trioctyl phospine oxide) in kerosene from phosphoric acid purification. The wastes are included in category of the hazard and poison materials which also radioactive, so that the wastes have to be treated to detoxification of the hazard and poison materials and decontamination of the radionuclides. The research of biochemistry oxidation process for treatment the simulation of organic liquid radioactive waste from laundry using mixture of aerobe bacteria of bacillus sp, pseudomonas sp, arthrobacter sp, and aeromonas sp have been carried out. The waste containing detergent 1,496 g/Litre, activity 10 -1 Ci/m 3 , with COD (Chemical Oxygen Demand) 128, BOD (Biological Oxygen Demand) 68 and TSS (Total Suspended Solid) 1000 ppm, it is treated by biochemistry oxidation with addition of bacteria which be fed nutrition of nitrogen and phosphor, and aeration. The result show that the bacteria can decompose the detergent to become carbon dioxyde and water so that can fulfill the quality standard of water group-B with content of BOD and COD are 6 and 10 ppm respectively, the time of decomposition is needed 106 hours to be fulfill the quality standard of water. The longer of process time will give bigger the total solid content in sludge, because the biomass generated from the colony of bacteria which life and dead to so much. (author)

  1. The role of exciton ionization processes in bulk heterojunction organic photovoltaic cells

    Science.gov (United States)

    Zou, Yunlong; Holmes, Russell

    2015-03-01

    Dissociating photogenerated excitons into their constituent charges is essential for efficient photoconversion in organic semiconductors. Organic photovoltaics cells (OPV) widely adopt a heterojunction architecture where dissociation is facilitated by charge transfer at a donor-acceptor (D-A) interface. Interestingly, recent work on MoOx/C60 Schottky OPVs has demonstrated that excitons in C60 may also undergo bulk-ionization to generate photocurrent, driven by the built-in field at the MoOx/C60 interface. Here, we show that bulk-ionization processes also contribute to the photocurrent in bulk heterojunction (BHJ) OPVs with fullerene-rich compositions. The short-circuit current density (JSC) in a MoOx/C60 Schottky OPVs shows almost no dependence on temperature down to 80 K. This characteristic of bulk-ionization allows the use of temperature-dependent measurements of JSC to distinguish dissociation by bulk-ionization from charge transfer at a D-A interface. For BHJ OPVs constructed using the D-A pairing of boron subphthalocyanine chloride (SubPc)-C60, bulk-ionization is found to contribute >10% of the total photocurrent and >30% of the photocurrent from C60. We further find that fullerene-rich SubPc-C60 BHJ OPVs show a larger open-circuit voltage (VOC) than evenly mixed BHJs due to the presence of bulk-ionization. This talk will examine the dependence of JSC and VOC on the relative fraction of dissociation by charge transfer and bulk-ionization processes.

  2. Studies of solution-processed organic light-emitting diodes and their materials

    Energy Technology Data Exchange (ETDEWEB)

    Hellerich, Emily [Iowa State Univ., Ames, IA (United States)

    2013-01-01

    A hitherto unexplored approach is presented in which a small molecule is used as a host to polymer guests in solution-processed OLEDs. We find that the small molecule host results in much more efficient devices than the often-used alternative polymer host when used for the guests presented. It is likely that nano- and microstructural differences between the hosts contribute to the improvements, which highlights some interesting characteristics that can help to better understand the nature of these mixtures. A number of the guests used in this study were newly synthesized benzobisoxazole-based copolymers. New organic copolymers are presented that are based on the chemical structure of benzobisoxazoles, which have been shown in the past to have good electron transporting properties. The novel concept in this publication pertains to a change in the direction of polymerization, also known as the conjugation pathway, which we show increases the emission efficiency. This work highlights a unique and useful property of organic semiconducting materials in that they can be synthesized to create the desired characteristics. Earlier work is described that kick-started in our research group the use of small molecules in solution-processed OLEDs. Originally these devices were to be used in magnetoresistance studies, but the project took a different path when the devices were more efficient than expected. The efficient use of small molecules in solution-processed OLEDs is highlighted, which at the time was not often the case. Also, the important observation of the effect of solvent choice on the resultant film is emphasized, with discussion of the likely cause of these effects. Microcavity OLEDs are introduced in which the transparent anode ITO is replaced with semi-transparent thin silver, which creates an optical cavity within the devices. The goal was to expand a previous work that created an on-chip spectrometer covering wavelengths 493 to 639 nm. In this case, a spin

  3. Solvent extraction of organic acids from stillage for its re-use in ethanol production process.

    Science.gov (United States)

    Castro, G A; Caicedo, L A; Alméciga-Díaz, C J; Sanchez, O F

    2010-06-01

    Stillage re-use in the fermentation stage in ethanol production is a technique used for the reduction of water and fermentation nutrients consumption. However, the inhibitory effect on yeast growth of the by-products and feed components that remains in stillage increases with re-use and reduces the number of possible recycles. Several methods such as ultrafiltration, electrodialysis and advanced oxidation processes have been used in stillage treatment prior its re-use in the fermentation stage. Nevertheless, few studies evaluating the effect of solvent extraction as a stillage treatment option have been performed. In this work, the inhibitory effect of serial stillage recycling over ethanol and biomass production was determined, using acetic acid as a monitoring compound during the fermentation and solvent extraction process. Raw palm oil methyl ester showed the highest acetic acid extraction from the aqueous phase, presenting a distribution coefficient of 3.10 for a 1:1 aqueous phase mixture:solvent ratio. Re-using stillage without treatment allowed up to three recycles with an ethanol production of 53.7 +/- 2.0 g L(-1), which was reduced 25% in the fifth recycle. Alternatively, treated stillage allowed up to five recycles with an ethanol final concentration of 54.7 +/- 1.3 g L(- 1). These results show that reduction of acetic acid concentration by an extraction process with raw palm oil methyl ester before re-using stillage improves the number of recycles without a major effect on ethanol production. The proposed process generates a palm oil methyl ester that contains organic acids, among other by-products, that could be used for product recovery and as an alternative fuel.

  4. Evaluation of factors controlling global secondary organic aerosol production from cloud processes

    Directory of Open Access Journals (Sweden)

    C. He

    2013-02-01

    Full Text Available Secondary organic aerosols (SOA exert a significant influence on ambient air quality and regional climate. Recent field, laboratorial and modeling studies have confirmed that in-cloud processes contribute to a large fraction of SOA production with large space-time heterogeneity. This study evaluates the key factors that govern the production of cloud-process SOA (SOAcld on a global scale based on the GFDL coupled chemistry-climate model AM3 in which full cloud chemistry is employed. The association between SOAcld production rate and six factors (i.e., liquid water content (LWC, total carbon chemical loss rate (TCloss, temperature, VOC/NOx, OH, and O3 is examined. We find that LWC alone determines the spatial pattern of SOAcld production, particularly over the tropical, subtropical and temperate forest regions, and is strongly correlated with SOAcld production. TCloss ranks the second and mainly represents the seasonal variability of vegetation growth. Other individual factors are essentially uncorrelated spatiotemporally to SOAcld production. We find that the rate of SOAcld production is simultaneously determined by both LWC and TCloss, but responds linearly to LWC and nonlinearly (or concavely to TCloss. A parameterization based on LWC and TCloss can capture well the spatial and temporal variability of the process-based SOAcld formation (R2 = 0.5 and can be easily applied to global three dimensional models to represent the SOA production from cloud processes.

  5. A highly energy-efficient flow-through electro-Fenton process for organic pollutants degradation

    International Nuclear Information System (INIS)

    Ma, Liang; Zhou, Minghua; Ren, Gengbo; Yang, Weilu; Liang, Liang

    2016-01-01

    Highlights: • A highly energy-efficient flow-through electro-Fenton reactor was designed. • It had high H 2 O 2 yield and low energy consumption for organic pollutants degradation. • The effect of operational parameters was optimized and possible process mechanism was studied. • The novel system performed wide practicability and potential for organic pollutants degradation. - Abstract: A highly energy-efficient flow-through Electro-Fenton (E-Fenton) reactor for oxidation of methylene blue (MB) from aqueous solution was designed using a perforated DSA as anode and the graphite felt modified by carbon black and polytetrafluoroethylene (PTFE) as cathode for the in situ generation of H 2 O 2 . The modified cathode had a high H 2 O 2 production with low energy consumption, which was characterized by scanning electron microscopy (SEM), nitrogen adsorption-desorption study and contact angle. The flow-through E-Fenton system was compared to the flow-by and regular one, and confirmed to be best on MB removal and TOC degradation. The operational parameters such as current density, pH, Fe 2+ concentration and flow rate were optimized. The MB and TOC removal efficiency of the effluents could keep above 90% and 50%, respectively, and the energy consumption was 23.0 kWh/kgTOC at the current density of 50 mA, pH 3, 0.3 mM Fe 2+ , and the flow rate of 7 mL/min. ·OH was proved to be the main oxidizing species in this system. After 5 times operation, the system, especially cathode, still showed good stability. Five more organic pollutants including orange II (OG), tartrazine, acetylsalicylic acid (ASA), tetracycline (TC) and 2,4-dichlorophen (2,4-DCP) were investigated and the electric energy consumption (EEC) was compared with literatures. All results demonstrated that this flow-through E-Fenton system was energy-efficient and potential for degradation of organic pollutants.

  6. Soft plasma processing of organic nanowires: a route for the fabrication of 1D organic heterostructures and the template synthesis of inorganic 1D nanostructures.

    Science.gov (United States)

    Alcaire, Maria; Sanchez-Valencia, Juan R; Aparicio, Francisco J; Saghi, Zineb; Gonzalez-Gonzalez, Juan C; Barranco, Angel; Zian, Youssef Oulad; Gonzalez-Elipe, Agustin R; Midgley, Paul; Espinos, Juan P; Groening, Pierangelo; Borras, Ana

    2011-11-01

    Hierarchical (branched) and hybrid metal-NPs/organic supported NWs are fabricated through controlled plasma processing of metalloporphyrin, metallophthalocyanine and perylene nanowires. The procedure is also applied for the development of a general template route for the synthesis of supported metal and metal oxide nanowires.

  7. [Morphogenetic processes and seasonal changes in the anatomic and histological organization of the Barents Sea sponge Halichondria panicea (Pallas)].

    Science.gov (United States)

    Ivanova, L V

    1978-10-01

    As a result of histological investigations of seasonal dynamics in the anatomical-tissue organization of the litoral sponge Halichondria panicea (Pallas), morphogenetical processes during different periods of its life cycle are described in detail. Correlations between different phases of sexual reproduction and conditions of anatomical and tissue organization in the maternal organism are stated. It is noted that tissue reduction of the definitive sponge Halichondria panicea during autumn--winter season is a natural phenomenon, regularly repeating in the life of the litoral sponge investigated, as a result of the maternal organism's "exhaustion" in the period of sexual embryogenesis.

  8. Electron-molecule chemistry and charging processes on organic ices and Titan's icy aerosol surrogates

    Science.gov (United States)

    Pirim, C.; Gann, R. D.; McLain, J. L.; Orlando, T. M.

    2015-09-01

    Electron-induced polymerization processes and charging events that can occur within Titan's atmosphere or on its surface were simulated using electron irradiation and dissociative electron attachment (DEA) studies of nitrogen-containing organic condensates. The DEA studies probe the desorption of H- from hydrogen cyanide (HCN), acetonitrile (CH3CN), and aminoacetonitrile (NH2CH2CN) ices, as well as from synthesized tholin materials condensed or deposited onto a graphite substrate maintained at low temperature (90-130 K). The peak cross sections for H- desorption during low-energy (3-15 eV) electron irradiation were measured and range from 3 × 10-21 to 2 × 10-18 cm2. Chemical and structural transformations of HCN ice upon 2 keV electron irradiation were investigated using X-ray photoelectron and Fourier-transform infrared spectroscopy techniques. The electron-beam processed materials displayed optical properties very similar to tholins produced by conventional discharge methods. Electron and negative ion trapping lead to 1011 charges cm-2 on a flat surface which, assuming a radius of 0.05 μm for Titan aerosols, is ∼628 charges/radius (in μm). The facile charge trapping indicates that electron interactions with nitriles and complex tholin-like molecules could affect the conductivity of Titan's atmosphere due to the formation of large negative ion complexes. These negatively charged complexes can also precipitate onto Titan's surface and possibly contribute to surface reactions and the formation of dunes.

  9. Design and process integration of organic Rankine cycle utilizing biomass for power generation

    Science.gov (United States)

    Ependi, S.; Nur, T. B.

    2018-02-01

    Indonesia has high potential biomass energy sources from palm oil mill industry activities. The growing interest on Organic Rankine Cycle (ORC) application to produce electricity by utilizing biomass energy sources are increasingly due to its successfully used for generating electricity from rejected waste heat to the environment in industrial processes. In this study, the potential of the palm oil empty fruit bunch, and wood chip have been used as fuel for biomass to generate electricity based ORC with combustion processes. The heat from combustion burner was transfer by thermal oil heater to evaporate ORC working fluid in the evaporator unit. The Syltherm-XLT thermal oil was used as the heat carrier from combustion burner, while R245fa was used as the working fluid for ORC unit. Appropriate designs integration from biomass combustion unit to ORC unit have been analyzed and proposed to generate expander shaft-work. Moreover, the effect of recuperator on the total system efficiency has also been investigated. It was observed that the fuel consumption was increased when the ORC unit equipped recuperator operated until certain pressure and decreased when operated at high pressure.

  10. Persistent organic pollutants in Mediterranean seawater and processes affecting their accumulation in plankton.

    Science.gov (United States)

    Berrojalbiz, Naiara; Dachs, Jordi; Del Vento, Sabino; Ojeda, María José; Valle, María Carmen; Castro-Jiménez, Javier; Mariani, Giulio; Wollgast, Jan; Hanke, Georg

    2011-05-15

    The Mediterranean and Black Seas are unique marine environments subject to important anthropogenic pressures due to riverine and atmospheric inputs of organic pollutants. Here, we report the results obtained during two east-west sampling cruises in June 2006 and May 2007 from Barcelona to Istanbul and Alexandria, respectively, where water and plankton samples were collected simultaneously. Both matrixes were analyzed for hexaclorochyclohexanes (HCHs), hexachlorobenzene (HCB), and 41 polychlorinated biphenyl (PCB) congeners. The comparison of the measured HCB and HCHs concentrations with previously reported dissolved phase concentrations suggests a temporal decline in their concentrations since the 1990s. On the contrary, PCB seawater concentrations did not exhibit such a decline, but show a significant spatial variability in dissolved concentrations with lower levels in the open Western and South Eastern Mediterranean, and higher concentrations in the Black, Marmara, and Aegean Seas and Sicilian Strait. PCB and OCPs (organochlorine pesticides) concentrations in plankton were higher at lower plankton biomass, but the intensity of this trend depended on the compound hydrophobicity (K(OW)). For the more persistent PCBs and HCB, the observed dependence of POP concentrations in plankton versus biomass can be explained by interactions between air-water exchange, particle settling, and/or bioaccumulation processes, whereas degradation processes occurring in the photic zone drive the trends shown by the more labile HCHs. The results presented here provide clear evidence of the important physical and biogeochemical controls on POP occurrence in the marine environment.

  11. Spatial Organization and Dynamics of Transcription Elongation and Pre-mRNA Processing in Live Cells

    Directory of Open Access Journals (Sweden)

    Miguel Sánchez-Álvarez

    2011-01-01

    Full Text Available During the last 30 years, systematic biochemical and functional studies have significantly expanded our knowledge of the transcriptional molecular components and the pre-mRNA processing machinery of the cell. However, our current understanding of how these functions take place spatiotemporally within the highly compartmentalized eukaryotic nucleus remains limited. Moreover, it is increasingly clear that “the whole is more than the sum of its parts” and that an understanding of the dynamic coregulation of genes is essential for fully characterizing complex biological phenomena and underlying diseases. Recent technological advances in light microscopy in addition to novel cell and molecular biology approaches have led to the development of new tools, which are being used to address these questions and may contribute to achieving an integrated and global understanding of how the genome works at a cellular level. Here, we review major hallmarks and novel insights in RNA polymerase II activity and pre-mRNA processing in the context of nuclear organization, as well as new concepts and challenges arising from our ability to gather extensive dynamic information at the single-cell resolution.

  12. Knowledge exchange processes in organizations and policy arenas: a narrative systematic review of the literature.

    Science.gov (United States)

    Contandriopoulos, Damien; Lemire, Marc; Denis, Jean-Louis; Tremblay, Emile

    2010-12-01

    This article presents the main results from a large-scale analytical systematic review on knowledge exchange interventions at the organizational and policymaking levels. The review integrated two broad traditions, one roughly focused on the use of social science research results and the other focused on policymaking and lobbying processes. Data collection was done using systematic snowball sampling. First, we used prospective snowballing to identify all documents citing any of a set of thirty-three seminal papers. This process identified 4,102 documents, 102 of which were retained for in-depth analysis. The bibliographies of these 102 documents were merged and used to identify retrospectively all articles cited five times or more and all books cited seven times or more. All together, 205 documents were analyzed. To develop an integrated model, the data were synthesized using an analytical approach. This article developed integrated conceptualizations of the forms of collective knowledge exchange systems, the nature of the knowledge exchanged, and the definition of collective-level use. This literature synthesis is organized around three dimensions of context: level of polarization (politics), cost-sharing equilibrium (economics), and institutionalized structures of communication (social structuring). The model developed here suggests that research is unlikely to provide context-independent evidence for the intrinsic efficacy of knowledge exchange strategies. To design a knowledge exchange intervention to maximize knowledge use, a detailed analysis of the context could use the kind of framework developed here. © 2010 Milbank Memorial Fund. Published by Wiley Periodicals Inc.

  13. Study on electroluminescence processes in dye-doped organic light-emitting diodes

    Energy Technology Data Exchange (ETDEWEB)

    Li Weizhi [State Key Laboratory of Electronic Thin Films and Integrated devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)], E-mail: leewz@uestc.edu.cn; Jiang Yadong; Wang Tao [State Key Laboratory of Electronic Thin Films and Integrated devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)

    2008-07-15

    Electroluminescence (EL) mechanism of dye-doped organic light-emitting diodes (OLEDs) was investigated by using three familiar fluorescent dyes, i.e., 5,12-Dihydro-5,12-dimethylquino [2,3-b]acridine-7,14-dione (DMQA), 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7-tetramethyljulolidyl-9-enyl) -4H-pyran(DCJTB), and 5,6,11,12-tetraphenylnaphthacene (Rubrene). EL spectra of the doped devices with structure of indium tin oxide (ITO)/N,N'-bis-(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'- diamine (NPB) (40 nm)/tris-(8-hydroxyquinolate)-aluminum (Alq{sub 3}) (x nm, x=0-40 nm)/dye: Alq{sub 3} (weight ratio{approx}1%, 2 nm)/Alq{sub 3} (48-x nm)/MgAg indicated that direct carrier trapping (DCT) process dominated light emission of devices. As a result, investigation of carrier-recombination site via doping, which is conventionally applied in OLEDs, is questionable since the doping site and the dopant itself may significantly influence the carrier-recombination process in the doped devices.

  14. Combined solar organic Rankine cycle with reverse osmosis desalination process: Energy, exergy, and cost evaluations

    Energy Technology Data Exchange (ETDEWEB)

    Nafey, A.S.; Sharaf, M.A. [Department of Engineering Science, Faculty of Petroleum and Mining Engineering, Suez Canal University, Suez (Egypt)

    2010-11-15

    Organic Rankine cycles (ORC) have unique properties that are well suited to solar power generation. In this work design and performance calculations are performed using MatLab/SimuLink computational environment. The cycle consists of thermal solar collectors (Flat Plate Solar Collector (FPC), or Parabolic Trough Collector (PTC), or Compound Parabolic Concentrator (CPC)) for heat input, expansion turbine for work output, condenser unit for heat rejection, pump unit, and Reverse Osmosis (RO) unit. Reverse osmosis unit specifications used in this work is based on Sharm El-Shiekh RO desalination plant. Different working fluids such as: butane, isobutane, propane, R134a, R152a, R245ca, and R245fa are examined for FPC. R113, R123, hexane, and pentane are investigated for CPC. Dodecane, nonane, octane, and toluene are allocated for PTC. The proposed process units are modeled and show a good validity with literatures. Exergy and cost analysis are performed for saturation and superheated operating conditions. Exergy efficiency, total exergy destruction, thermal efficiency, and specific capital cost are evaluated for direct vapor generation (DVG) process. Toluene and Water achieved minimum results for total solar collector area, specific total cost and the rate of exergy destruction. (author)

  15. High purity heavy water production: need for total organic carbon determination in process water streams

    International Nuclear Information System (INIS)

    Ayushi; Kumar, Sangita D.; Reddy, A.V.R.; Vithal, G.K.

    2009-01-01

    In recent times, demand for high purity heavy water (99.98% pure) in industries and laboratories has grown by manifold. Its application started in nuclear industry with the design of CANDU reactor, which uses natural uranium as fuel. In this reactor the purest grade of heavy water is used as the moderator and the primary coolant. Diverse industrial applications like fibre optics, medicine, semiconductors etc. use high purity heavy water extensively to achieve better performance of the specific material. In all these applications there is a stringent requirement that the total organic carbon content (TOC) of high purity heavy water should be very low. This is because the presence of TOC can lead to adverse interactions in different applications. To minimize the TOC content in the final product there is a need to monitor and control the TOC content at each and every stage of heavy water production. Hence a simple, rapid and accurate method was developed for the determination of TOC content in process water samples. The paper summarizes the results obtained for the TOC content in the water samples collected from process streams of heavy water production plant. (author)

  16. [Emission characteristics and safety evaluation of volatile organic compounds in manufacturing processes of automotive coatings].

    Science.gov (United States)

    Zeng, Pei-Yuan; Li, Jian-Jun; Liao, Dong-Qi; Tu, Xiang; Xu, Mei-Ying; Sun, Guo-Ping

    2013-12-01

    Emission characteristics of volatile organic compounds (VOCs) were investigated in an automotive coating manufacturing enterprise. Air samples were taken from eight different manufacturing areas in three workshops, and the species of VOCs and their concentrations were measured by gas chromatography-mass spectrometry (GC-MS). Safety evaluation was also conducted by comparing the concentration of VOCs with the permissible concentration-short term exposure limit (PC-STEL) regulated by the Ministry of Health. The results showed that fifteen VOCs were detected in the indoor air of the automotive coatings workshop, including benzene, toluene, ethylbenzene, xylene, ethyl acetate, butyl acetate, methyl isobutyl ketone, propylene glycol monomethyl ether acetate, trimethylbenzene and ethylene glycol monobutyl ether, Their concentrations widely ranged from 0.51 to 593.14 mg x m(-3). The concentrations of TVOCs were significantly different among different manufacturing processes. Even in the same manufacturing process, the concentrations of each component measured at different times were also greatly different. The predominant VOCs of indoor air in the workshop were identified to be ethylbenzene and butyl acetate. The concentrations of most VOCs exceeded the occupational exposure limits, so the corresponding control measures should be taken to protect the health of the workers.

  17. Mechanisms of self-organized criticality in social processes of knowledge creation

    Science.gov (United States)

    Tadić, Bosiljka; Dankulov, Marija Mitrović; Melnik, Roderick

    2017-09-01

    In online social dynamics, a robust scale invariance appears as a key feature of collaborative efforts that lead to new social value. The underlying empirical data thus offers a unique opportunity to study the origin of self-organized criticality (SOC) in social systems. In contrast to physical systems in the laboratory, various human attributes of the actors play an essential role in the process along with the contents (cognitive, emotional) of the communicated artifacts. As a prototypical example, we consider the social endeavor of knowledge creation via Questions and Answers (Q&A). Using a large empirical data set from one of such Q&A sites and theoretical modeling, we reveal fundamental characteristics of SOC by investigating the temporal correlations at all scales and the role of cognitive contents to the avalanches of the knowledge-creation process. Our analysis shows that the universal social dynamics with power-law inhomogeneities of the actions and delay times provides the primary mechanism for self-tuning towards the critical state; it leads to the long-range correlations and the event clustering in response to the external driving by the arrival of new users. In addition, the involved cognitive contents (systematically annotated in the data and observed in the model) exert important constraints that identify unique classes of the knowledge-creation avalanches. Specifically, besides determining a fine structure of the developing knowledge networks, they affect the values of scaling exponents and the geometry of large avalanches and shape the multifractal spectrum. Furthermore, we find that the level of the activity of the communities that share the knowledge correlates with the fluctuations of the innovation rate, implying that the increase of innovation may serve as the active principle of self-organization. To identify relevant parameters and unravel the role of the network evolution underlying the process in the social system under consideration, we

  18. Mechanisms of self-organized criticality in social processes of knowledge creation.

    Science.gov (United States)

    Tadić, Bosiljka; Dankulov, Marija Mitrović; Melnik, Roderick

    2017-09-01

    In online social dynamics, a robust scale invariance appears as a key feature of collaborative efforts that lead to new social value. The underlying empirical data thus offers a unique opportunity to study the origin of self-organized criticality (SOC) in social systems. In contrast to physical systems in the laboratory, various human attributes of the actors play an essential role in the process along with the contents (cognitive, emotional) of the communicated artifacts. As a prototypical example, we consider the social endeavor of knowledge creation via Questions and Answers (Q&A). Using a large empirical data set from one of such Q&A sites and theoretical modeling, we reveal fundamental characteristics of SOC by investigating the temporal correlations at all scales and the role of cognitive contents to the avalanches of the knowledge-creation process. Our analysis shows that the universal social dynamics with power-law inhomogeneities of the actions and delay times provides the primary mechanism for self-tuning towards the critical state; it leads to the long-range correlations and the event clustering in response to the external driving by the arrival of new users. In addition, the involved cognitive contents (systematically annotated in the data and observed in the model) exert important constraints that identify unique classes of the knowledge-creation avalanches. Specifically, besides determining a fine structure of the developing knowledge networks, they affect the values of scaling exponents and the geometry of large avalanches and shape the multifractal spectrum. Furthermore, we find that the level of the activity of the communities that share the knowledge correlates with the fluctuations of the innovation rate, implying that the increase of innovation may serve as the active principle of self-organization. To identify relevant parameters and unravel the role of the network evolution underlying the process in the social system under consideration, we

  19. Photochemical processing of organic aerosol at nearby continental sites: contrast between urban plumes and regional aerosol

    Directory of Open Access Journals (Sweden)

    J. G. Slowik

    2011-03-01

    Full Text Available As part of the BAQS-Met 2007 field campaign, Aerodyne time-of-flight aerosol mass spectrometers (ToF-AMS were deployed at two sites in southwestern Ontario from 17 June to 11 July 2007. One instrument was located at Harrow, ON, a rural, agriculture-dominated area approximately 40 km southeast of the Detroit/Windsor/Windsor urban area and 5 km north of Lake Erie. The second instrument was located at Bear Creek, ON, a rural site approximately 70 km northeast of the Harrow site and 50 km east of Detroit/Windsor. Positive matrix factorization analysis of the combined organic mass spectral dataset yields factors related to secondary organic aerosol (SOA, direct emissions, and a factor tentatively attributed to the reactive uptake of isoprene and/or condensation of its early generation reaction products. This is the first application of PMF to simultaneous AMS measurements at different sites, an approach which allows for self-consistent, direct comparison of the datasets. Case studies are utilized to investigate processing of SOA from (1 fresh emissions from Detroit/Windsor and (2 regional aerosol during periods of inter-site flow. A strong correlation is observed between SOA/excess CO and photochemical age as represented by the NOx/NOy ratio for Detroit/Windsor outflow. Although this correlation is not evident for more aged air, measurements at the two sites during inter-site transport nevertheless show evidence of continued atmospheric processing by SOA production. However, the rate of SOA production decreases with airmass age from an initial value of ~10.1 μg m−3 ppmvCO−1 h−1 for the first ~10 h of plume processing to near-zero in an aged airmass (i.e. after several days. The initial SOA production rate is comparable to the observed rate in Mexico City over similar timescales.

  20. Electronic Processes at Organic−Organic Interfaces: Insight from Modeling and Implications for Opto-electronic Devices †

    KAUST Repository

    Beljonne, David

    2011-02-08

    We report on the recent progress achieved in modeling the electronic processes that take place at interfaces between π-conjugated materials in organic opto-electronic devices. First, we provide a critical overview of the current computational techniques used to assess the morphology of organic: organic heterojunctions; we highlight the compromises that are necessary to handle large systems and multiple time scales while preserving the atomistic details required for subsequent computations of the electronic and optical properties. We then review some recent theoretical advances in describing the ground-state electronic structure at heterojunctions between donor and acceptor materials and highlight the role played by charge-transfer and long-range polarization effects. Finally, we discuss the modeling of the excited-state electronic structure at organic:organic interfaces, which is a key aspect in the understanding of the dynamics of photoinduced electron-transfer processes. © 2010 American Chemical Society.

  1. The distribution of some rare metals in the process of separation of organic matter from Estonian dictyonema argillite

    International Nuclear Information System (INIS)

    Palvadre, R.; Ahelik, V.

    1993-01-01

    The distribution of rare metals Mo, U and V in the process of separation of organic matter from Maardu and Toolse argillite s is discussed. The beneficiation process of argillite consists of the hydro cycling treatment, in the course of which organic matter is separated as a light fraction, followed by direct flotation of organic matter and pyrite concentrates. Determinations of Mo and U were made by X-ray fluorescence, V by titration and pyrite by titration of iron. It can be concluded that rare metals Mo, U and V were concentrating in organic matter, their recovery in pyrite and quartz was negligible, depending on the degree of pyrite separation. The recovery of rare metals, especially that of V in the mineral phase, was more considerable in the processing of Maardu argillite, whose content of clay minerals was higher than that of Toolse argillite. 4 tabs., 6 refs

  2. Organic priority substances and microbial processes in river sediments subject to contrasting hydrological conditions.

    Science.gov (United States)

    Zoppini, Annamaria; Ademollo, Nicoletta; Amalfitano, Stefano; Casella, Patrizia; Patrolecco, Luisa; Polesello, Stefano

    2014-06-15

    Flood and drought events of higher intensity and frequency are expected to increase in arid and semi-arid regions, in which temporary rivers represent both a water resource and an aquatic ecosystem to be preserved. In this study, we explored the variation of two classes of hazardous substances (Polycyclic Aromatic Hydrocarbons and Nonylphenols) and the functioning of the microbial community in river sediments subject to hydrological fluctuations (Candelaro river basin, Italy). Overall, the concentration of pollutants (∑PAHs range 8-275ngg(-1); ∑NPs range 299-4858ngg(-1)) suggests a moderate degree of contamination. The conditions in which the sediments were tested, flow (high/low) and no flow (wet/dry/arid), were associated to significant differences in the chemical and microbial properties. The total organic carbon contribution decreased together with the stream flow reduction, while the contribution of C-PAHs and C-NPs tended to increase. NPs were relatively more concentrated in sediments under high flow, while the more hydrophobic PAHs accumulated under low and no flow conditions. Passing from high to no flow conditions, a gradual reduction of microbial processes was observed, to reach the lowest specific bacterial carbon production rates (0.06fmolCh(-1)cell(-1)), extracellular enzyme activities, and the highest doubling time (40h) in arid sediments. In conclusion, different scenarios for the mobilization of pollutants and microbial processes can be identified under contrasting hydrological conditions: (i) the mobilization of pollutants under high flow and a relatively higher probability for biodegradation; (ii) the accumulation of pollutants during low flow and lower probability for biodegradation; (iii) the drastic reduction of pollutant concentrations under dry and arid conditions, probably independently from the microbial activity (abiotic processes). Our findings let us infer that a multiple approach has to be considered for an appropriate water

  3. No knowledge without processes : process mining as a tool to find out what people and organizations really do

    NARCIS (Netherlands)

    van der Aalst, W.M.P.; Fred, A.; Filipe, J.; Dietz, J.L.G.; Aveiro, D.; Liu, K.

    2014-01-01

    Recently, process mining emerged as a new scientific discipline on the interface between process models and event data. Whereas conventional Business Process Management (BPM) approaches are mostly model-driven with little consideration for event data, the increasing availability of high-quality data

  4. Nitrogen and organic carbon cycling processes in tidal marshes and shallow estuarine habitats

    Science.gov (United States)

    Bergamaschi, B. A.; Downing, B. D.; Pellerin, B. A.; Kraus, T. E. C.; Fleck, J.; Fujii, R.

    2016-02-01

    Tidal wetlands and shallow water habitats can be sites of high aquatic productivity, and they have the potential of exchanging this newly produced organic carbon with adjacent deeper habitats. Indeed, export of organic carbon from wetlands and shallow water habitats to pelagic food webs is one of the primary ecosystem functions targeted in tidal wetland restorations. Alternatively, wetlands and shallow water habitats can function as retention areas for nutrients due to the nutrient demand of emergent macrophytes and denitrification in anoxic zones. They can also remove phytoplankton and non-algal particles from the aquatic food webs because the shallower waters can result in higher rates of benthic grazing and higher settling due to lower water velocities. We conducted studies in wetland and channel sites in the San Francisco estuary (USA) to investigate the dynamics of nutrients and carbon production at a variety of temporal scales. We collected continuous time series of nutrients, oxygen, chlorophyll and pH in conjunction with continuous acoustic measurement of water velocity and discharge to provide mass controls and used simple biogeochemical models to assess rates. We found a high degree of temporal variability in individual systems, corresponding to, for example, changes in nutrient supply, water level, light level, wind, wind direction, and other physical factors. There was also large variability among the different systems, probably due to differences in flows and geomorphic features. We compare the aquatic productivity of theses environments and speculate as to the formative elements of each. Our findings demonstrate the complex interaction between physical, chemical, and biological factors that determine the type of production and degree of export from tidal wetlands and shallow water habitats, suggesting that a clearer picture of these processes is important for guiding future large scale restoration efforts.

  5. Correlations of Sensory Processing and Visual Organization Ability with Participation in School-Aged Children with Down Syndrome

    Science.gov (United States)

    Wuang, Yee-Pay; Su, Chwen-Yng

    2011-01-01

    Previous work has highlighted delays and differences in cognitive, language, and sensorimotor functions in children diagnosed with Down syndrome (DS). However, sensory processing and visual organization abilities have not been well-examined in DS to date. This study aimed to investigate the developmental profile of sensory processing and visual…

  6. Noninvasive in-process thickness measurement of an organic layer on steel using x-ray scattering

    International Nuclear Information System (INIS)

    Moskowitz, J.

    1992-01-01

    The motivation for this work was the need for a non-contacting composition-independent in-process technique for rapidly measuring the mass per unit area (open-quotes surface densityclose quotes) of a continuous slab of organic material prepared on a stainless steel base. It was essential that the technique be adaptable to eventual implementation for on-line process control

  7. The Socialization Process of Street Children in the Youth Gangs and Groups of Organized Crime in Local Community. Preliminary Report

    Directory of Open Access Journals (Sweden)

    Małgorzata Michel

    2013-12-01

    Full Text Available This article includes the research report on the socialization process of children in the street, youth gangs, and organized criminal groups in local communities. The author has analysed the signs and communication codes located on walls in local communities. This is very important to the socialization process of the youth street gangs.

  8. The Impact of the Learning Organization Environment on the Organizational Learning Process in the Korean Business Context

    Science.gov (United States)

    Song, Ji Hoon; Jeung, Chang-Wook; Cho, Sei Hyoung

    2011-01-01

    Purpose: The primary purposes of the current paper are to: provide theoretically clear concepts of the learning organization (LO) and organizational learning (OL) process; and empirically test the relationships among research constructs--environmental aspects of the LO and three types of OL processes at the levels of individual, group/team, and…

  9. Removal of Refractory Organics from Biologically Treated Landfill Leachate by Microwave Discharge Electrodeless Lamp Assisted Fenton Process

    Directory of Open Access Journals (Sweden)

    Jiuyi Li

    2015-01-01

    Full Text Available Biologically treated leachate usually contains considerable amount of refractory organics and trace concentrations of xenobiotic pollutants. Removal of refractory organics from biologically treated landfill leachate by a novel microwave discharge electrodeless lamp (MDEL assisted Fenton process was investigated in the present study in comparison to conventional Fenton and ultraviolet Fenton processes. Conventional Fenton and ultraviolet Fenton processes could substantially remove up to 70% of the refractory organics in a membrane bioreactor treated leachate. MDEL assisted Fenton process achieved excellent removal performance of the refractory components, and the effluent chemical oxygen demand concentration was lower than 100 mg L−1. Most organic matters were transformed into smaller compounds with molecular weights less than 1000 Da. Ten different polycyclic aromatic hydrocarbons were detected in the biologically treated leachate, most of which were effectively removed by MDEL-Fenton treatment. MDEL-Fenton process provides powerful capability in degradation of refractory and xenobiotic organic pollutants in landfill leachate and could be adopted as a single-stage polishing process for biologically treated landfill leachate to meet the stringent discharge limit.

  10. Organic molecules based on dithienyl-2,1,3-benzothiadiazole as new donor materials for solution-processed organic photovoltaic cells

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Zhonglian; Fan, Benhu; Ouyang, Jianyong [Department of Materials Science and Engineering, National University of Singapore, Singapore 117574 (Singapore); Xue, Feng [Department of Chemistry, National University of Singapore, Singapore 117573 (Singapore); Adachi, Chihaya [Center for Future Chemistry, Kyushu University, 744 Motooka, Nishi, Fukuoka 819-0395 (Japan)

    2010-12-15

    Polymers based on dithienyl-2,1,3-benzothiadiazole (TBT) have received strong attention as the donor materials of polymer photovoltaic cells (PVs), since they can have a low band gap. But soluble small organic molecules based on TBT have been rarely studied. This paper reports the synthesis of two small organic molecules based on TBT and their application as the donor materials of solution-processed bulk heterojunction organic photovoltaic cells (OPVs). These compounds were soluble in common organic solvents, such as chloroform, chlorobenzene and tetrahydrofuran. They have band gaps comparable to poly(3-hexylthiophene) (P3HT) and lower HOMO and LUMO (HOMO: highest occupied molecular orbital, LUMO: lowest unoccupied molecular orbital) levels than P3HT. These molecules and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) were used as the donors and acceptor to fabricate bulk heterojunction OPVs through solution processing. After optimization of the experimental conditions, power conversion efficiency (PCE) of 0.66% was achieved on the solution-processed OPVs under AM 1.5G, 100 mW cm{sup -2} illumination. (author)

  11. Synthesis, Processing, and Characterization of Inorganic-Organic Hybrid Cross-Linked Silica, Organic Polyimide, and Inorganic Aluminosilicate Aerogels

    Science.gov (United States)

    Nguyen, Baochau N.; Guo, Haiquan N.; McCorkle, Linda S.

    2014-01-01

    As aerospace applications become ever more demanding, novel insulation materials with lower thermal conductivity, lighter weight and higher use temperature are required to fit the aerospace application needs. Having nanopores and high porosity, aerogels are superior thermal insulators, among other things. The use of silica aerogels in general is quite restricted due to their inherent fragility, hygroscopic nature, and poor mechanical properties, especially in extereme aerospace environments. Our research goal is to develop aerogels with better mechanical and environmental stability for a variety of aeronautic and space applications including space suit insulation for planetary surface missions, insulation for inflatable structures for habitats, inflatable aerodynamic decelerators for entry, descent and landing (EDL) operations, and cryotank insulation for advance space propulsion systems. Different type of aerogels including organic-inorganic polymer reinforced (hybrid) silica-based aerogels, polyimide aerogels and inorganic aluminosilicate aerogels have been developed and examined.

  12. A double stage dry-wet-fermentation process for a fast and safe digestion of different kinds of organic material

    International Nuclear Information System (INIS)

    Busch, G.; Sieber, M.; Buschmann, J.; Burkhardat, M.

    2009-01-01

    The fermentation of organic material is a four-step-process. It is admissible to merge the first two steps (hydrolysis and acidification) to hydrolysis in general and the last two steps (aceto genesis and methano genesis) to methano genesis. The Brandenburg University of Technology in Cottbus has devised a double stage dry-wet-fermentation process for fast and safe anaerobic degradation. Using these processes, it is possible to decompose different kinds of organic material like renewable material (e. g. maize silage), waste (e. g. household-waste) and industrial material (e. g. glycerine). (Author)

  13. Treatment of toxic and hazardous organic wastes by wet oxidation process with oxygenated water at low temperature

    International Nuclear Information System (INIS)

    Piccinno, T.; Salluzzo, A.; Nardi, L.; Gili, M.; Luce, A.; Troiani, F.; Cornacchia, G.

    1989-11-01

    The wet oxidation process using air or molecular oxygen is a well-known process from long time. It is suitable to oxidize several types of waste refractory to the usual biological, thermal and chemical treatments. The drastic operating conditions (high pressures and temperatures) prevented its industrial development. In the last years a new interest was assigned to the process for the treatment of nuclear wastes (organic resins and exhaust organic wastes); the treatment is carried out at widely reduced operating conditions (atmospheric pressure and boiling temperature) by means of metallic catalysts and hydrogen peroxide. With some limits, the wet oxidation with hydrogen peroxide at low temperature can be applied to conventional waste waters containing toxic organic compounds. In the present report are summarized the activities developed at ENEA Fuel Cycle Department by the task force 'Deox' constituted by laboratory and plant specialists in order to verify the application of the wet oxidation process to the treatment of the toxic wastes. (author)

  14. Simple process of hybrid white quantum dot/organic light-emitting diodes by using quantum dot plate and fluorescence

    Science.gov (United States)

    Lee, Ho Won; Lee, Ki-Heon; Lee, Jae Woo; Kim, Jong-Hoon; Yang, Heesun; Kim, Young Kwan

    2015-02-01

    In this work, the simple process of hybrid quantum dot (QD)/organic light-emitting diode (OLED) was proposed to apply a white illumination light by using QD plate and organic fluorescence. Conventional blue fluorescent OLEDs were firstly fabricated and then QD plates of various concentrations, which can be controlled of UV-vis absorption and photoluminescence spectrum, were attached under glass substrate of completed blue devices. The suggested process indicates that we could fabricate the white device through very simple process without any deposition of orange or red organic emitters. Therefore, this work would be demonstrated that the potential simple process for white applications can be applied and also can be extended to additional research on light applications.

  15. Organization and post-transcriptional processing of focal adhesion kinase gene

    Directory of Open Access Journals (Sweden)

    Enslen Hervé

    2006-08-01

    Full Text Available Abstract Background Focal adhesion kinase (FAK is a non-receptor tyrosine kinase critical for processes ranging from embryo development to cancer progression. Although isoforms with specific molecular and functional properties have been characterized in rodents and chicken, the organization of FAK gene throughout phylogeny and its potential to generate multiple isoforms are not well understood. Here, we study the phylogeny of FAK, the organization of its gene, and its post-transcriptional processing in rodents and human. Results A single orthologue of FAK and the related PYK2 was found in non-vertebrate species. Gene duplication probably occurred in deuterostomes after the echinoderma embranchment, leading to the evolution of PYK2 with distinct properties. The amino acid sequence of FAK and PYK2 is conserved in their functional domains but not in their linker regions, with the absence of autophosphorylation site in C. elegans. Comparison of mouse and human FAK genes revealed the existence of multiple combinations of conserved and non-conserved 5'-untranslated exons in FAK transcripts suggesting a complex regulation of their expression. Four alternatively spliced coding exons (13, 14, 16, and 31, previously described in rodents, are highly conserved in vertebrates. Cis-regulatory elements known to regulate alternative splicing were found in conserved alternative exons of FAK or in the flanking introns. In contrast, other reported human variant exons were restricted to Homo sapiens, and, in some cases, other primates. Several of these non-conserved exons may correspond to transposable elements. The inclusion of conserved alternative exons was examined by RT-PCR in mouse and human brain during development. Inclusion of exons 14 and 16 peaked at the end of embryonic life, whereas inclusion of exon 13 increased steadily until adulthood. Study of various tissues showed that inclusion of these exons also occurred, independently from each other, in a

  16. Fish otolith biomineralization process: first investigations about organic matrix and growth of Triglidae (Scorpaeniformes otoliths

    Directory of Open Access Journals (Sweden)

    Stefano Montanini

    2015-11-01

    Full Text Available Otolith formation involves rhythmic variations in the deposition and size of organic matrix framework and carbonate crystals, resulting in the formation of macroscopic translucent and opaque rings and microscopic zonations (growth increments (Morales Nin, 2000. As in most biominerals, the otolith matrix forms only 2-3 % of its weight, but it is admitted that it has a considerable importance in the otolith crystallization processes of nucleation, growth, orientation and growth control. The goal of this study is to characterize the matrix protein composition in the otoliths of Triglidae (Scorpaeniformes as a first step to understand molecular mechanisms of otolith formation according to biology and ecology of the species. In particular 500 sagittal otoliths from six gurnard species were analysed: Chelidonichthys cuculus, C. lucerna, Eutrigla gurnardus, Lepidotrigla cavillone, L. dieuzeidei and Trigloporus lastoviza. Protein contents were estimated by Bradford method and the urea 8 M extracts were loaded into a polyacrylamide gel, separated by SDS page and detected by Silver staining (Sigma followed the protocol of Borelli et al. (2001 with some modifications regarding protein precipitation that was enhanced by using TCA, trichloroacetic acid, 100% w/v. The urea soluble fractions revealed a unique large band around 50-55 kDa. Another common clear band was visible at the top of the separating gel (proteins >300/350 kDa unable to enter into the pores of polyacrylamide gels (12%. The complexity of the protein mixtures was investigated by 2-D electrophoresis (Gel TGX 4-20%; proteins were separated on the basis of both isoelectric point (pI and molecular size. A common protein pattern of 50-75 kDa were found in all gurnards showing a similar composition of organic matter even if the 2-D maps of otolith samples showed specie-specific variation in acid protein fractions in all the pairwise comparison. This result confirmed that the amino acid composition

  17. Thermal and mechanical stabilization process of the organic fraction of the municipal solid waste

    Energy Technology Data Exchange (ETDEWEB)

    Giudicianni, Paola, E-mail: giudicianni@irc.cnr.it [DIC-MAPI – Università degli Studi di Napoli Federico II (Italy); Bozza, Pio, E-mail: pi.bozza@studenti.unina.it [DIC-MAPI – Università degli Studi di Napoli Federico II (Italy); Sorrentino, Giancarlo, E-mail: g.sorrentino@unina.it [DIC-MAPI – Università degli Studi di Napoli Federico II (Italy); Ragucci, Raffaele, E-mail: ragucci@irc.cnr.it [Istituto di Ricerche sulla Combustione – C.N.R. Napoli (Italy)

    2015-10-15

    Graphical abstract: Display Omitted - Highlights: • A domestic scale prototype for the pre-treatment of OFMSW has been tested. • Two grinding techniques are compared and thermopress is used for the drying stage. • Increasing temperature up to 170 °C reduces energy consumption of the drying stage. • In the range 5–10 bar a reduction of 97% of the initial volume is obtained. • In most cases energy recovery from the dried waste matches energy consumption. - Abstract: In the present study a thermo-mechanical treatment for the disposal of the Organic Fraction of Municipal Solid Waste (OFMSW) at apartment or condominium scale is proposed. The process presents several advantages allowing to perform a significant volume and moisture reduction of the produced waste at domestic scale thus producing a material with an increased storability and improved characteristics (e.g. calorific value) that make it available for further alternative uses. The assessment of the applicability of the proposed waste pretreatment in a new scheme of waste management system requires several research steps involving different competences and application scales. In this context, a preliminary study is needed targeting to the evaluation and minimization of the energy consumption associated to the process. To this aim, in the present paper, two configurations of a domestic appliance prototype have been presented and the effect of some operating variables has been investigated in order to select the proper configuration and the best set of operating conditions capable to minimize the duration and the energy consumption of the process. The performances of the prototype have been also tested on three model mixtures representing a possible daily domestic waste and compared with an existing commercially available appliance. The results obtained show that a daily application of the process is feasible given the short treatment time required and the energy consumption comparable to the one of

  18. Direct and mediated impacts of product and process characteristics on consumers’ choice of organic vs. conventional chicken

    DEFF Research Database (Denmark)

    Marian, Livia; Thøgersen, John

    2012-01-01

    There is a lack of research into why consumers value process characteristics. In this study, we test the hypothesis that the impact of process characteristics such as organic and free-range on consumers’ choices of food products is at least partly mediated through expected eating quality or taste...... are important for consumers, not only in and off themselves, but partly because consumers make inferences about eating quality from knowledge about such process characteristics....

  19. Enhanced WWTP effluent organic matter removal in hybrid ozonation-coagulation (HOC) process catalyzed by Al-based coagulant

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Xin [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an, Shaanxi Province, 710055 (China); Jin, Pengkang, E-mail: pkjin@hotmail.com [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an, Shaanxi Province, 710055 (China); Hou, Rui [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an, Shaanxi Province, 710055 (China); Yang, Lei [Department of Materials Science and Engineering, Monash University, Clayton, VIC, 3800 (Australia); Wang, Xiaochang C., E-mail: xcwang@xauat.edu.cn [School of Environmental and Municipal Engineering, Xi’an University of Architecture and Technology, Xi’an, Shaanxi Province, 710055 (China)

    2017-04-05

    Highlights: • A novel HOC process was firstly put forward to apply in wastewater reclamation. • Interactions between ozone and Al-based coagulants was found in the HOC process. • Ozonation can be catalyzed and enhanced by Al-based coagulants in the HOC process. • HOC process showed better organics removal than pre-ozonation-coagulation process. - Abstract: A novel hybrid ozonation-coagulation (HOC) process was developed for application in wastewater reclamation. In this process, ozonation and coagulation occurred simultaneously within a single unit. Compared with the conventional pre-ozonation-coagulation process, the HOC process exhibited much better performance in removing dissolved organic matters. In particular, the maximal organic matters removal efficiency was obtained at the ozone dosage of 1 mgO{sub 3}/mg DOC at each pH value (pH 5, 7 and 9). In order to interpret the mechanism of the HOC process, ozone decomposition was monitored. The results indicated that ozone decomposed much faster in the HOC process. Moreover, by using the reagent of O{sub 3}-resistant hydroxyl radical (·OH) probe compound, para-chlorobenzoic acid (pCBA), and electron paramagnetic resonance (EPR) analysis, it was observed that the HOC process generated higher content of ·OH compared with pre-ozonation process. This indicates that the ·OH oxidation reaction as the key step can be catalyzed and enhanced by Al-based coagulants and their hydrolyzed products in this developed process. Thus, based on the catalytic effects of Al-based coagulants on ozonation, the HOC process provides a promising alternative to the conventional technology for wastewater reclamation in terms of higher efficiency.

  20. Highly efficient red phosphorescent organic light-emitting diodes based on solution processed emissive layer

    International Nuclear Information System (INIS)

    Liu, Baiquan; Xu, Miao; Tao, Hong; Ying, Lei; Zou, Jianhua; Wu, Hongbin; Peng, Junbiao

    2013-01-01

    Highly efficient red phosphorescent organic polymer light-emitting diodes (PhOLEDs) were fabricated based on a solution-processed small-molecule host 4,4′-bis(N-carbazolyl)-1,1′-biphenyl (CBP) by doping an iridium complex, tris(1-(2,6-dimethylphenoxy)-4-(4-chlorophenyl)phthalazine)iridium (III) (Ir(MPCPPZ) 3 ). A hole blocking layer 1,3,5-tri(1-phenyl-1H-benzo[d]imidazol-2-yl)phenyl (TPBI) with a function of electron transport was thermally deposited onto the top of CBP layer. The diode with the structure of ITO/PEDOT:PSS (50 nm)/CBP:Ir(MPCPPZ) 3 (55 nm)/TPBI (30 nm)/Ba (4 nm)/Al (120 nm) showed an external quantum efficiency (QE ext ) of 19.3% and luminous efficiency (LE) of 18.3 cd/A at a current density of 0.16 mA/cm 2 , and Commission International de I'Eclairage (CIE) coordinates of (0.607, 0.375). It was suggested that the diodes using TPBI layer exhibited nearly 100% internal quantum efficiency and one order magnitude enhanced LE or QE ext efficiencies. -- Highlights: • Efficient red PhOLEDs based on a solution-processed small-molecule host were fabricated. • By altering volume ratio of chloroform/chlorobenzene solvent, we got best film quality of CBP. • EQE of the diode was 19.3%, indicating nearly 100% internal quantum yield was achieved