Treatment of Radioactive Contaminated Soil and Concrete Wastes Using the Regulatory Clearance

Energy Technology Data Exchange (ETDEWEB)

Kang, Il Sik; Ryu, W. S.; Kim, T. K.; Shon, J. S.; Ahn, S. J.; Lee, Y. H.; Bae, S. M.; Hong, D. S.; Ji, Y. Y.; Lee, B. C

2008-11-15

In the radioactive waste storage facilities at the Korea Atomic Energy Research Institute (KAERI) in Daejoen, there are thousands drums of radioactive contaminated soil and concrete wastes. The soil and concrete wastes were generated in 1988 during the decommissioning process of the research reactor and the attached radioactive waste treatment facility which were located in Seoul. The wastes were transported to Daejeon and have been stored since then. At the generation time, the radioactive contamination of the wastes was very low, and the radionuclides in the wastes was Co-60 and Cs-137. As the wastes have been stored for more than 20 years, the radioactivity concentration of the wastes has been decayed to become very extremely low. The wastes are needed to be treated because they take up large spaces at the storage facility. Also by treating the wastes, final disposal cost can be saved. So, the regulatory clearance was considered as a treatment method for the soil and concrete wastes with extremely low radioactivity concentration.

Development of floor smear sampler (floor radioactive contamination measuring instrument) for nuclear facilities

International Nuclear Information System (INIS)

Miyagawa, Minoru; Ito, Haruo; Nozawa, Katsuro; Shinohara, Yotaro; Hashimoto, Hiroshi.

1980-01-01

The control of the floor contamination with radioactive substances in nuclear facilities is strictly carried out by smear method, in which the contaminants on floor surfaces are wiped off with filter papers or cloths, and the contamination density on the floor surfaces is measured through their intensity of radioactivity. This wiping work is laborious since it is carried out in leaning-over posture when many samples must be taken in wide floor area. Therefore, to achieve labor saving in this work, an automatic sampler was developed. In the floor smear sampler developed, samples are taken on long band type wiping cloths only by handle operation, and the sample numbers are printed. When many samples are taken in wide floor area, this is especially effective, and the labor saving by 1/3 to 1/2 can be achieved. At present, this sampler is put in practical use in Hamaoka Nuclear Power Station. At the time of trial manufacture, the method of wiping, the mechanisms of wiping, cloth feeding and running, the contact pressure and the number of times of wiping affecting wiping efficiency and the required torque of a motor were examined. The developed sampler is that of constant contact pressure, vibration wiping type, and the rate of sampling is 10 sec per one sample. 100 samples can be taken on one roll of wiping cloth. The results of performance test are reported. (Kako, I.)

Radioactive standards and calibration methods for contamination monitoring instruments

Energy Technology Data Exchange (ETDEWEB)

Yoshida, Makoto [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-06-01

Contamination monitoring in the facilities for handling unsealed radioactive materials is one of the most important procedures for radiation protection as well as radiation dose monitoring. For implementation of the proper contamination monitoring, radiation measuring instruments should not only be suitable to the purpose of monitoring, but also be well calibrated for the objective qualities of measurement. In the calibration of contamination monitoring instruments, quality reference activities need to be used. They are supplied in different such as extended sources, radioactive solutions or radioactive gases. These reference activities must be traceable to the national standards or equivalent standards. On the other hand, the appropriate calibration methods must be applied for each type of contamination monitoring instruments. In this paper, the concepts of calibration for contamination monitoring instruments, reference sources, determination methods of reference quantities and practical calibration methods of contamination monitoring instruments, including the procedures carried out in Japan Atomic Energy Research Institute and some relevant experimental data. (G.K.)

Incineration facilities for treatment of radioactive wastes: a review

Energy Technology Data Exchange (ETDEWEB)

Perkins, B.L.

1976-02-01

A description is given of incinerator installations in the US and in foreign countries. Included are descriptions of inactive incinerators, incinerator facilities currently in operation, and incinerator installations under construction. Special features of each installation and operational problems of each facility are emphasized. Problems in the incineration of radioactive waste are discussed in relation to the composition of the waste and the amount and type of radioactive contaminant.

Incineration facilities for treatment of radioactive wastes: a review

International Nuclear Information System (INIS)

Perkins, B.L.

1976-02-01

A description is given of incinerator installations in the US and in foreign countries. Included are descriptions of inactive incinerators, incinerator facilities currently in operation, and incinerator installations under construction. Special features of each installation and operational problems of each facility are emphasized. Problems in the incineration of radioactive waste are discussed in relation to the composition of the waste and the amount and type of radioactive contaminant

Technologies for remediating radioactively contaminated land

International Nuclear Information System (INIS)

Pearl, M.

2000-01-01

This paper gives an overview of technologies that can be used for the remediation of radioactively contaminated ground. There are a wide variety of techniques available -most have established track records for contaminated ground, though in general many are only just being adapted to use for radioactively contaminated ground. 1) Remediation techniques for radioactively contaminated ground involve either removal of the contamination and transfer to a controlled/contained facility such as the national LLW repository at Drigg, or 2) immobilization, solidification and stabilization of the contamination where the physical nature of the soil is changed, or an 'agent' is added to the soil, to reduce the migration of the contaminants, or 3) isolation and containment of the contaminated ground to reduce contaminant migration and control potential detrimental effects to human health. Where contamination has to be removed, ex situ and in situ techniques are available which minimize the waste requiring disposal to an LLW repository. These techniques include: 1) detector-based segregation 2) soil washing by particle separations 3) oil washing with chemical leaching agents 4) electro remediation 5) phyto remediation. Although many technologies are potentially applicable, their application to the remediation of a specific contaminated site is dependent on a number of factors and related to detailed site characterization studies, results from development trials and BPEO (best practicable environmental option) studies. Those factors considered of particular importance are: 1) the clean-up target 2) technical feasibility relative to the particular site, soil and contaminant characteristics, and time frame 3) site infrastructure arrangements and needs, the working life of the site and the duration of institutional care 4) long-term monitoring arrangements for slow remedial techniques or for immobilization and containment techniques 5) validation of the remediation 6) health and

Radiation safety for incineration of radioactive waste contaminated by cesium

International Nuclear Information System (INIS)

Veryuzhs'kij, Yu.V.; Gryin'ko, O.M.; Tokarevs'kij, V.V.

2016-01-01

Problems in the treatment of radioactive waste contaminated by cesium nuclides are considered in the paper. Chornobyl experience in the management of contaminated soil and contaminated forests is analyzed in relation to the accident at Fukushima-1. The minimization of release of cesium aerosols into atmosphere is very important. Radiation influence of inhaling atmosphere aerosols polluted by cesium has damage effect for humans. The research focuses on the treatment of forests contaminated by big volumes of cesium. One of the most important technologies is a pyro-gasification incineration with chemical reactions of cesium paying attention to gas purification problems. Requirements for process, physical and chemical properties of treatment of radioactive waste based on the dry pyro-gasification incineration facilities are considered in the paper together with the discussion of details related to incineration facilities. General similarities and discrepancies in the environmental pollution caused by the accidents at Chornobyl NPP and Fukushima-1 NPP in Japan are analyzed

Non-radioactive stand-in for radioactive contamination. I. Non-radioactive tests

International Nuclear Information System (INIS)

Rohe, M.J.; Rankin, W.N.; Postles, R.L.

1985-01-01

Candidate non-radioactive materials for use as a stand-in for radioactive contamination during application of a high-pressure, hot water decontamination were identified and evaluated. A stand-in for radioactive contamination is needed to evaluate the decontaminability of replacement canyon cranes at the manufacturers location where actual radioactive contamination cannot be used. This evaluation was conducted using high-pressure, hot-water at 420 psi, 190 0 F, and 20 gal/min through a 1/8-in.-diam nozzle, the decontamination technique preferred by SRP Separations Department for this application. A non-radioactive stand-in for radioactive contamination was desired that would be removed by direct blast stream contact but would remain intact on surfaces where direct contact does not occur. This memorandum describes identification of candidate non-radioactive stand-in materials and evaluation of these materials in screening tests and tests with high-pressure, hot-water blasting. The following non-radioactive materials were tested: carpenter's line chalk; typing correction fluid; dye penetrant developer; latex paint with attapulyite added; unaltered latex paint; gold enamel; layout fluid; and black enamel. Results show that blue layout fluid and gold enamel have similar adherence that is within the range expected for actual radioactive contamination. White latex paint has less adherence than expected for actual radioactive contamination. The film was removed at a rate of 2 . Black enamel has more adherence than expected from actual radioactive contamination. In these tests ASTM No. 2B surfaces were harder to clean than either ASTM No. 1 or electropolished surfaces which had similar cleaning properties. A 90 0 blast angle was more effective than a 45 0 blast angle. In these tests there was no discernible effect of blast distance between 1 and 3 ft

Estimation of contaminant transport in groundwater beneath radioactive waste disposal facilities

International Nuclear Information System (INIS)

Wang, J.C.; Tauxe, J.D.; Lee, D.W.

1995-01-01

Performance assessments are required for low-level radioactive waste disposal facilities to demonstrate compliance with the performance objectives contained in either 10 CFR 61, open-quotes Licensing Requirements for Land Disposal of Radioactive Waste,close quotes or U.S. Department of Energy Order 5820.2A, open-quotes Radioactive Waste Management.close quotes The purpose of a performance assessment is to provide detailed, site-specific analyses of all credible pathways by which radionuclides could escape from the disposal facility into the environment. Among these, the groundwater pathway analysis usually involves complex numerical simulations. This paper demonstrates that the use of simpler analytical models avoids the complexity and opacity of the numerical simulations while capturing the essential physical behavior of a site

Decontamination and decommissioning of the Argonne National Laboratory East Area radioactively contaminated surplus facilities: Final report

International Nuclear Information System (INIS)

Kline, W.H.; Fassnacht, G.F.; Moe, H.J.

1987-07-01

ANL has decontaminated and decommissioned (D and D) seven radiologically contaminated surplus facilities at its Illinois site: a ''Hot'' Machine Shop (Building 17) and support facilities; Fan House No. 1 (Building 37), Fan House No. 2 (Building 38), the Pangborn Dust Collector (Building 41), and the Industrial Waste Treatment Plant (Building 34) for exhaust air from machining of radioactive materials. Also included were a Nuclear Materials Storage Vault (Building 16F) and a Nuclear Research Laboratory (Building 22). The D and D work involved dismantling of all process equipment and associated plumbing, ductwork, drain lines, etc. After radiation surveys, floor and wall coverings, suspended ceilings, room partitions, pipe, conduit and electrical gear were taken down as necessary. In addition, underground sewers were excavated. The grounds around each facility were also thoroughly surveyed. Contaminated materials and soil were packaged and shipped to a low-level waste burial site, while nonactive debris was buried in the ANL landfill. Clean, reusable items were saved, and clean metal scrap was sold for salvage. After the decommissioning work, each building was torn down and the site relandscaped. The project was completed in 1985, ahead of schedule, with substantial savings

Design of good manufacturing facility for sterile radioactive pharmaceuticals

International Nuclear Information System (INIS)

Shin, B.C.; Choung, W.M.; Park, S.H.; Lee, K.I.; Park, J.H.; Park, K.B.

2002-01-01

Based on the GMP codes for radiopharmaceuticals in U.K. and some advanced countries, suitable guidelines for the production facility have been established and followed them up. The facility designs were fairly modified to maintain cleanliness criteria for installation in the existing radioisotope production facilities which are installed only in radiation safety points of view. Detailed design brief was drawn up by the Hyundai Engineering staffs, on the basis of initial planning and conceptual design was carried out by authors. Hot cells were installed in preparation room for radioactive handling. As hot cells under negative air pressure are not properly airtight, the surrounding environment was designed to keep less than class 10,000. Hot cells were designed to maintain less than class 1 0,000 and partially less than class 1 00 for production of sterile products. Final products will be autoclaved for sterilization after filling. To avoid contamination by microorganisms and particles of surrounding area, air curtain with vertical laminar flow will be installed between anteroom and corridor. In a pharmaceutical environment, the main consideration is the protection of the product. Thus, work station is held above ambient pressure. However, when handling radioactive materials, air pressure for work station should be lower than in surrounding areas to protect the operators and the remainder of the facility from airborne radioactive contamination. As Radiopharmaceuticals are radioactive materials for medical use, changing room could be held higher pressure than any other zones. It is expected that the facility will be effectively used for both routine preparation and research for sterile radiopharmaceuticals. (Author)

Control of the surface radioactive contamination in the field of biological research

International Nuclear Information System (INIS)

Calvo, S.; Encina, A. de la; Gaspar, J.; Macias, M. T.; Sanchez, A.; Usera, F.

2012-01-01

The manipulation of unsealed sources in biomedical research involves significant risk of radioactive contamination. the aim of this study has been to analyze the radioactive contamination occurring in the field of biomedical research, assessing its magnitude, identifying the equipment that can be contaminated with higher probability and monitoring the evolution of the contaminations production taking into account the radioisotopes and the activities uses, and the radiation protection control applied. The data used for this study correspond to a very lengthy period of time and it have been collected in the radioactive facility, of the Centro Nacional de Biotecnologia (CSIC), a very large biological research centre that can be used perfectly as a reference for this area. The results obtained show a gradual and significant decrease in the incidence of the radioactive contamination. This is due to the optimization of radiation protection standards applied and the implementation or a systematic operational radiation protection program. (Author) 13 refs.

Radioactive contamination in imported foods

International Nuclear Information System (INIS)

Kan, Kimiko; Maki, Toshio; Nagayama, Toshihiro; Hashimoto, Hideki; Kawai, Yuka; Kobayashi, Maki; Shioda, Hiroko; Nishima, Taichiro

1990-01-01

On April 26, 1986, explosion occurred in Chernobyl nuclear power station in USSR, and radioactivity contamination was brought about in almost all countries in the world. In European countries, crops were contaminated directly with radioactive fallout to high concentration. Also in Japan, after one week the radioactivity higher than usual was detected in environment, and also in vegetables, milk, tea leaves and others. Thereafter, in order to cope with the import of contaminated foods, inspection and watch system was strengthened by deciding the interim limit of radioactive concentration. However the cases of exceeding the interim limit were often reported. In order to remove the harmful foods due to radioactive contamination and to meet the fear of consumers, the authors measured the radioactive concentration in foods distributed in Tokyo and investigated the actual state of contamination. The samples were 920 imported foods. The experimental method, the preparation of samples, the method of analysis and the results are reported. The samples in which the radioactive concentration exceeding 50 Bq/kg was detected were 25 cases. The food having the high frequency of detection was flavors. (K.I.)

On-site radioactive soil contamination at the Andreeva Bay shore technical base, Northwest Russia.

Science.gov (United States)

Reistad, O; Dowdall, M; Selnaes, Ø G; Standring, W J F; Hustveit, S; Steenhuisen, F; Sørlie, A

2008-07-01

The radioactive waste (RAW) storage site at Andreeva Bay in the Russian Northwest has experienced radioactive contamination both as a result of activities carried out at the site and due to incidents that have occurred there in the past such as accidental releases of radioactive materials. The site is an interesting case study for decommissioning due to the extremely large amounts of radioactivity present at the site and the conditions under which it is stored; very little has been previously published in the scientific literature about this site. This paper complements the paper describing dose rates at Andreeva Bay which is published in this issue of Journal of Environmental Radioactivity by the same authors. This study presents new data related to the activity concentrations of (137)Cs and (90)Sr in surface soils and measurements of alpha- and beta-particle fluxes taken at different areas around the site. Limited data on 60Co is also presented. The results of the study indicate that the main areas of site contamination are associated with the former spent nuclear fuel storage facility at Building 5, due to accidental discharges which began in 1982. Substantial contamination is also observed at the solid radioactive waste storage facilities, probably due to the ingress of water into these facilities. More than 240 samples were measured: maximum contamination levels were 1 x 10(6)Bq/kg (137)Cs (mean value 4.1 x 10(5)Bq/kg) and 4 x 10(6)Bq/kg (90)Sr (mean value 1.2 x1 0(5)Bq/kg). Localised patches of alpha and beta contamination were also observed throughout the site.

Low-level radioactive mixed waste land disposal facility -- Permanent disposal

International Nuclear Information System (INIS)

Erpenbeck, E.G.; Jasen, W.G.

1993-03-01

Radioactive mixed waste (RMW) disposal at US Department of Energy (DOE) facilities is subject to the Resource Conservation and Recovery Act of 1976 (RCRA) and the Hazardous and Solid Waste Amendments of 1984 (HSWA). Westinghouse Hanford Company, in Richland, Washington, has completed the design of a radioactive mixed waste land disposal facility, which is based on the best available technology compliant with RCRA. When completed, this facility will provide permanent disposal of solid RMW, after treatment, in accordance with the Land Disposal Restrictions. The facility includes a double clay and geosynthetic liner with a leachate collection system to minimize potential leakage of radioactive or hazardous constituents from the landfill. The two clay liners will be capable of achieving a permeability of less than 1 x 10 -7 cm/s. The two clay liners, along with the two high density polyethylene (HDPE) liners and the leachate collection and removal system, provide a more than conservative, physical containment of any potential radioactive and/or hazardous contamination

Investigation to radioactive contamination of pool water in IMEF

International Nuclear Information System (INIS)

Song, Ung Sup; Jung, Yang Hong; Lee, J. H.; Lee, H. K.

2003-06-01

The pool (3x6x10) in irradiated materials examination facility is usually used for the purpose of taking the specimen out of cask loaded into the pool, and carrying in/out the specimen to/ from the hot cell. Always, it must be cared for the water into the pool to be fine condition because all operation are worked with the naked eye during taking an irradiated materials out of the cask and plunging them in the bucket-elevator. In the aspects of the radioactive remained substances in the water must be controlled so that the amount of substances to be lower than the standard amount prescribed by RCA Korea Activity in a part of radioactive contamination control. In consequence, an expertness of status and a practical use of skill make possible the prevention of radioactive material's diffusion or the radioactive contamination of pool water and safety work

Electrolyze radioactive contamination away

International Nuclear Information System (INIS)

Wedman, D.E.; Martinez, H.E.; Nelson, T.O.

1996-01-01

The Los Alamos National Laboratory Plutonium Facility is using electrolysis to clean the surfaces of hazardous materials. In the past, contaminated metals were cleaned with concentrated acids. Although these treatments make the surfaces safer, they produce other radioactive and toxic wastes in turn. Anodic current passes through a piece of stainless steel submersed in a sodium nitrate solution, and steel dissolves at the surfaces. Surface contamination strips away along with the surface layers. The authors are using this electrolysis approach to remove plutonium and americium from stainless steel and uranium. Unlike acid washing processes, electrolytic decontamination can be accomplished quickly. Little waste is generated regardless of how much material has to be removed from the surface. Material removal is proportional to the applied current, which gives the operator control over the rate and extent of decontamination

Training manual for process operation and management of radioactive waste treatment facility

Energy Technology Data Exchange (ETDEWEB)

Shon, J. S.; Kim, K. J.; Ahn, S. J. [and others

2004-12-01

Radioactive Waste Treatment Facility (RWTF) has been operating for safe and effective treatment of radioactive wastes generated in the Korea Atomic Energy Research Institute (KAERI). In RWTF, there are evaporation, bituminization and solar evaporation processes for liquid waste, solid waste treatment process and laundry process. As other radioactive waste treatment facilities in foreign countries, the emergency situation such as fire and overflow of liquid waste can be taken place during the operation and result in the spread of contamination of radioactivity. So, easy and definite operating procedure is necessary for the safe operation of the facility. This manual can be available as easy and concise training materials for new employees and workers dispatched from service agency. Especially, in case of emergency urgently occurred during operation, everyone working in the facility can quickly stop the facility following this procedure.

Training manual for process operation and management of radioactive waste treatment facility

International Nuclear Information System (INIS)

Shon, J. S.; Kim, K. J.; Ahn, S. J.

2004-12-01

Radioactive Waste Treatment Facility (RWTF) has been operating for safe and effective treatment of radioactive wastes generated in the Korea Atomic Energy Research Institute (KAERI). In RWTF, there are evaporation, bituminization and solar evaporation processes for liquid waste, solid waste treatment process and laundry process. As other radioactive waste treatment facilities in foreign countries, the emergency situation such as fire and overflow of liquid waste can be taken place during the operation and result in the spread of contamination of radioactivity. So, easy and definite operating procedure is necessary for the safe operation of the facility. This manual can be available as easy and concise training materials for new employees and workers dispatched from service agency. Especially, in case of emergency urgently occurred during operation, everyone working in the facility can quickly stop the facility following this procedure

Test and evaluation of radioactively contaminated transducers and transmitters

International Nuclear Information System (INIS)

Strahm, R.C.

1983-01-01

People in the nuclear industries face some unique problems when handling, testing, or examining transducers and transmitters that have been radioactively contaminated. Although many people and organizations, including EG and G Idaho, have performed such work for many years, there are no set, structured approaches or procedures. This paper discusses a disciplined laboratory approach to contaminated transducer testing and evaluation, utilizing equipment and facilities developed specifically for this type of work

49 CFR 175.705 - Radioactive contamination.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Radioactive contamination. 175.705 Section 175.705... Regulations Applicable According to Classification of Material § 175.705 Radioactive contamination. (a) A... (radioactive) materials that may have been released from their packagings. (b) When contamination is present or...

Survey of radioactive contamination of foodstuffs

International Nuclear Information System (INIS)

Lee, W. R.; Lee, C. W.; Choi, G. S.; Cho, Y. H.; Kang, M. J.; Cheong, K. H.; Kim, H. R.; Kwak, J. Y.

2005-11-01

The purpose of this study is to survey and assess radioactive contamination of foodstuffs in order to reduce the probability of intake of contaminated foodstuffs. Based on survey and assessment, final goal is to improve the public health by radiation protection. Sampled foodstuffs items are collected from the markets : one group are imported foodstuffs and the other group are domestic foodstuffs producted around nuclear facilities. After pretreatments such as drying, ashing, and homogenization, all samples were analyzed by gamma spectrometer system. The 137 Cs radionuclide was only measured among the regulation radionuclides ( 137 Cs, 134 Cs, 131 I) of food code. All radionuclides of the domestic foodstuffs collected around nuclear facilities were below Minimum Detectable Activity (MDA). But the activity concentrations of Inonotus obliquus (Chaga mushooms) from Russia ranged up to 171.27 (average value : 36.65) Bq/kg-fresh. In the case of blueberry jam, the radioactivity of 137 Cs is higher than expected value. Other samples are below MDA except some spices. Based on the previous and present results, it should be strengthen to survey for Inontus obliquus (Chaga mushooms), of which the radioactivity shows the range from MDA up to 800.01 Bq/kg-fresh. It should assess the public radiation exposure via food chain because it has the excess provability of the maximum permitted level of food code, which is regulation of KFDA. The development method based on international standard would be used at radioactive analysis as well as education of practical workers and it could be applied as the basis data for amending the analysis method of food code. Our country only surveys gamma emitting radionuclides till now but international organization or foreign countries for example EU survey alpha and beta emitting radionuclides as well as gamma emitting radionuclides. So our country should also research necessity of survey for alpha and beta emitting radionuclides

Radioactive contamination incidents involving protective clothing

International Nuclear Information System (INIS)

Reichelt, R.A.; Clay, M.E.; Eichorst, A.J.

1998-01-01

The study focuses on incidents at Department of Energy facilities involving the migration of radioactive contaminants through protective clothing. The authors analyzed 68 occurrence reports for the following factors: (1) type of work, (2) working conditions, (3) type of anti-contamination material; (4) area of body or clothing contaminated; and (5) nature of spread of contamination. A majority of reports identified strenuous work activities such as maintenance, construction, or decontamination and decommissioning projects. The reports also indicated adverse working conditions that included hot and humid or cramped work environments. The type of anti-contamination clothing most often identified was cotton or water-resistant disposable clothing. Most of the reports also indicated contaminants migrating through perspiration-soaked areas, typically in the knees and forearms. On the basis of their survey, the authors recommend the use of improved engineering controls and resilient, breathable, waterproof protective clothing for work in hot, humid, or damp areas where the possibility of prolonged contact with contamination cannot be easily avoided or controlled. 1 ref., 6 figs., 1 tab

Radioactive contamination in monitors received for calibration

International Nuclear Information System (INIS)

Dias, Paulo S.; Santos, Gilvan C. dos; Brunelo, Maria Antonieta G.; Paula, Tiago C. de; Pires, Marina A.; Borges, Jose C.

2013-01-01

The Calibration Laboratory - LABCAL, from the Research Center for Metrology and Testing - METROBRAS, MRA Comercio de Instrumentos Eletronicos Ltda., began activities in October 2008 and, in August 2009, decided to establish a procedure for monitoring tests, external and internal, of all packages received from customers, containing instruments for calibration. The aim was to investigate possible contamination radioactive on these instruments. On July 2011, this procedure was extended to packagings of personal thermoluminescent dosemeters - TLD, received by the newly created Laboratory Laboratorio de Dosimetria Pessoal - LDP . In the monitoring procedure were used monitors with external probe, type pancake, MRA brand, models GP - 500 and MIR 7028. During the 37 months in which this investigation was conducted, were detected 42 cases of radioactive contamination, with the following characteristics: 1) just one case was personal dosimeter, TLD type; 2) just one case was not from a packing from nuclear medicine service - was from a mining company; 3) contamination occurred on packs and instruments, located and/or widespread; 4) contamination values ranged from slightly above the level of background radiation to about a thousand fold. Although METROBRAS has facilities for decontamination, in most cases, especially those of higher contamination, the procedure followed was to store the contaminated material in a room used for storage of radioactive sources. Periodically, each package and/or instrument was monitored, being released when the radiation level matched the background radiation. Every contamination detected, the client and/or owner of the instrument was informed. The Brazilian National Energy Commission - CNEN, was informed, during your public consultation for reviewing the standard for nuclear medicine services, held in mid-2012, having received from METROBRAS the statistical data available at the time. The high frequency of contamination detected and the high

Levels of surface contamination with radioactive materials at workplaces of nuclear research centre at Rez

International Nuclear Information System (INIS)

Hoelgye, Z.; Nemcova, I.; Kasikova, M.; Popper, J.; Chysky, J.

1983-01-01

A hygiene supervision unit at workplaces of the nuclear Research Institute in Rez monitored on a long-term basis surface contamination with radioactive substances. Surface contamination was found at workplaces with open sources. Of the 4343 monitored places action levels were only exceeded in 13 cases. The obtained data were used for typifying workplaces with the highest level of surface contamination, to determine in certain instances the mechanism of the escape of radioactive substances from insulating facilities and to determine the rate of the spread of the radioactive substance into adjacent non-active workplaces. (author)

Risk assessment methodology for evaluating releases of radioactively contaminated materials

International Nuclear Information System (INIS)

Chen, S.Y.

1993-01-01

Extensive decontamination and decommissioning (D ampersand D) activities are expected to be required in the near future in association with license termination of nuclear power facilities and cleanup efforts at the U.S. Department of Energy's (DOE's) weapons production facilities. In advance of these D ampersand D activities, it is becoming increasingly urgent that standards be established for the release of materials with residual radioactive contamination. The only standards for unrestricted release that currently exist address surface contamination. The methods used to justify those standards were developed some 20 yr ago and may not satisfy today's criteria. Furthermore, the basis of setting standards has moved away from the traditional open-quotes instrumentation-basedclose quotes concept toward a open-quotes risk-basedclose quotes approach. Therefore, as new release standards are developed, it will be necessary that risk assessment methodology consistent with modern concepts be incorporated into the process. This paper discusses recent developments in risk methodology and issues and concerns regarding the future development of standards for the release of radioactively contaminated materials

Radioactive contamination incidents involving protective clothing

Energy Technology Data Exchange (ETDEWEB)

Reichelt, R.; Clay, M.; Eichorst, J.

1996-10-01

The study focuses on incidents at Department of Energy (DOE) facilities involving the migration of radioactive contaminants through protective clothing. The authors analyzed 68 occurrence reports for the following factors: (1) type of work; (2) working conditions; (3) type of anti-contamination (anti-C) material; (4) area of body or clothing contaminated; and (5) nature of spread of contamination. A majority of reports identified strenuous work activities such as maintenance, construction, or decontamination and decommissioning (D&D) projects. The reports also indicated adverse working conditions that included hot and humid or cramped work environments. The type of anti-C clothing most often identified was cotton or water-resistant, disposable clothing. Most of the reports also indicated contaminants migrating through perspiration-soaked areas, typically in the knees and forearms. On the basis of their survey, the authors recommend the use of improved engineering controls and resilient, breathable, waterproof protective clothing for work in hot, humid, or damp areas where the possibility of prolonged contact with contamination cannot be easily avoided or controlled.

Radioactive contamination incidents involving protective clothing

International Nuclear Information System (INIS)

Reichelt, R.; Clay, M.; Eichorst, J.

1996-10-01

The study focuses on incidents at Department of Energy (DOE) facilities involving the migration of radioactive contaminants through protective clothing. The authors analyzed 68 occurrence reports for the following factors: (1) type of work; (2) working conditions; (3) type of anti-contamination (anti-C) material; (4) area of body or clothing contaminated; and (5) nature of spread of contamination. A majority of reports identified strenuous work activities such as maintenance, construction, or decontamination and decommissioning (D ampersand D) projects. The reports also indicated adverse working conditions that included hot and humid or cramped work environments. The type of anti-C clothing most often identified was cotton or water-resistant, disposable clothing. Most of the reports also indicated contaminants migrating through perspiration-soaked areas, typically in the knees and forearms. On the basis of their survey, the authors recommend the use of improved engineering controls and resilient, breathable, waterproof protective clothing for work in hot, humid, or damp areas where the possibility of prolonged contact with contamination cannot be easily avoided or controlled

The development of the American National Standard 'control of radioactive surface contamination on materials equipment and facilities to be released for uncontrolled use'

International Nuclear Information System (INIS)

Shapiro, J.

1980-01-01

A new standard submitted by the Health Physics Society Standards Committee to the American National Standards Institute concerning radioactive surface contamination of materials and equipment is discussed. The chronological events in the development of this standard are given. The standard provides criteria for the release for uncontrolled use of materials, equipment and facilities contaminated or potentially contaminated with radioactivity. Permissible contamination limits are specified for: 1) long lived alpha emitters except natural uranium and thorium, 2) more hazardous beta-gamma emitters, 3) less hazardous beta-gamma emitters and 4) natural uranium and thorium. A contamination reference level of 1000 dpm/100 cm 2 for 90 Sr was set as the basis for assigning limits to radionuclides presenting an ingestion hazard and other radionuclides were grouped based on the values of their maximum permissible concentration (MPC) in water relative to 90 Sr. The contamination limit for 239 Pu was chosen as the basis for assigning limits based on MPC in air to radionuclides presenting an inhalation hazard; a value of 100 dpm/100 cm 2 was adopted in the standard. An upper limit of 5000 dpm/100 cm 2 for surface contamination was selected for the standard. (UK)

Dismantlement and Radioactive Waste Management of DPRK Nuclear Facilities

Energy Technology Data Exchange (ETDEWEB)

Jooho, W.; Baldwin, G. T.

2005-04-01

One critical aspect of any denuclearization of the Democratic People’s Republic of Korea (DPRK) involves dismantlement of its nuclear facilities and management of their associated radioactive wastes. The decommissioning problem for its two principal operational plutonium facilities at Yongbyun, the 5MWe nuclear reactor and the Radiochemical Laboratory reprocessing facility, alone present a formidable challenge. Dismantling those facilities will create radioactive waste in addition to existing inventories of spent fuel and reprocessing wastes. Negotiations with the DPRK, such as the Six Party Talks, need to appreciate the enormous scale of the radioactive waste management problem resulting from dismantlement. The two operating plutonium facilities, along with their legacy wastes, will result in anywhere from 50 to 100 metric tons of uranium spent fuel, as much as 500,000 liters of liquid high-level waste, as well as miscellaneous high-level waste sources from the Radiochemical Laboratory. A substantial quantity of intermediate-level waste will result from disposing 600 metric tons of graphite from the reactor, an undetermined quantity of chemical decladding liquid waste from reprocessing, and hundreds of tons of contaminated concrete and metal from facility dismantlement. Various facilities for dismantlement, decontamination, waste treatment and packaging, and storage will be needed. The shipment of spent fuel and liquid high level waste out of the DPRK is also likely to be required. Nuclear facility dismantlement and radioactive waste management in the DPRK are all the more difficult because of nuclear nonproliferation constraints, including the call by the United States for “complete, verifiable and irreversible dismantlement,” or “CVID.” It is desirable to accomplish dismantlement quickly, but many aspects of the radioactive waste management cannot be achieved without careful assessment, planning and preparation, sustained commitment, and long

Dismantlement and Radioactive Waste Management of DPRK Nuclear Facilities

International Nuclear Information System (INIS)

Jooho, W.; Baldwin, G.T.

2005-01-01

One critical aspect of any denuclearization of the Democratic People's Republic of Korea (DPRK) involves dismantlement of its nuclear facilities and management of their associated radioactive wastes. The decommissioning problem for its two principal operational plutonium facilities at Yongbyun, the 5MWe nuclear reactor and the Radiochemical Laboratory reprocessing facility, alone present a formidable challenge. Dismantling those facilities will create radioactive waste in addition to existing inventories of spent fuel and reprocessing wastes. Negotiations with the DPRK, such as the Six Party Talks, need to appreciate the enormous scale of the radioactive waste management problem resulting from dismantlement. The two operating plutonium facilities, along with their legacy wastes, will result in anywhere from 50 to 100 metric tons of uranium spent fuel, as much as 500,000 liters of liquid high-level waste, as well as miscellaneous high-level waste sources from the Radiochemical Laboratory. A substantial quantity of intermediate-level waste will result from disposing 600 metric tons of graphite from the reactor, an undetermined quantity of chemical decladding liquid waste from reprocessing, and hundreds of tons of contaminated concrete and metal from facility dismantlement. Various facilities for dismantlement, decontamination, waste treatment and packaging, and storage will be needed. The shipment of spent fuel and liquid high level waste out of the DPRK is also likely to be required. Nuclear facility dismantlement and radioactive waste management in the DPRK are all the more difficult because of nuclear nonproliferation constraints, including the call by the United States for 'complete, verifiable and irreversible dismantlement,' or 'CVID.' It is desirable to accomplish dismantlement quickly, but many aspects of the radioactive waste management cannot be achieved without careful assessment, planning and preparation, sustained commitment, and long completion times

Effect of pre-entry instruction as an additional part of radiation training beginner's course on reduction of radioactive contamination in two independent unsealed radioisotope facilities

International Nuclear Information System (INIS)

Matsuda, Naoki; Yoshida, Masahiro; Takao, Hideaki; Kaneko, Mamoru; Okumura, Yutaka; Shimasaki, Tatsuya; Kojima, Akihiro; Shiraishi, Yoshioki; Horiuchi, Seikoh

2005-01-01

The education for radiation workers is essential for the safety of radiation facility that stands on radiation protection practice by each worker. Japanese laws concerning radiation safety requires each radiation worker attending the 6 hours beginner's training course before entering the control area. However, in unsealed radioisotope facilities, radioactive contaminations in the control area may still take place because practical procedures for radiation safety vary depending on the type of experiments and the characteristics of radioisotopes. Therefore, an additional and practical training for each radiation worker is needed. In an attempt to give the workers an additional training of this kind, the pre-entry instruction was performed independently in Center for Frontier Life Sciences, Nagasaki University and in Institute of Resource Development and Analysis Kumamoto University. In this study, the efficacy of the instruction in each facility was assessed quantitatively on the basis of the incidence of contamination in the control area. The instruction covered laboratory rules, radioisotope ordering information, description of sign-up sheets, radioactive waste management, use of survey meters, and lab tour with an appropriate modification to meet with a specificity of each experiment. The instruction was given to beginners and to refreshers who have not handled radioisotopes for a long period, in a face-to-face manner for 1 hour before they start working radioisotopes. To examine the education effect on the reduction of contamination in a typical and frequently used laboratory, the contamination in molecular biology room of Nagasaki University was surveyed directly by a GM survey meter on a daily basis. In Kumamoto University, contamination on the surface of the entire floor in the control area was surveyed monthly by the smear method to know the education effect on general reduction of contamination. The results revealed that the number of contamination decreased

Facilities for the treatment of radioactively contaminated water in nuclear power plants

International Nuclear Information System (INIS)

1978-01-01

The regulation is to be applied to design, construction and operation of facilities for the treatment of contaminated water in stationary nuclear power plants with LWR and HTR. The facilities are to be designed, constructed and operated in such manner that (a) imcontrolled discharge of contaminated water is avoided (Paragraph 46 section 1, no. 1 Radiation Protection Regulation) (b) the activity discharged with water is as low as possible ( paragraph 46, section 2, no. 2 Radiation Protection Regulation) (c)contaminated water will not get into the ground, unless this is permitted by a license (paragraph 46 section 6 Radiation Protection Regulation) (d) the radiation exposure resulting from direct radiation, contamination and inhalation of the personnel working with the facility is as low as possible and, at the most, corresponds to the values fixed in the regulation (paragraph 28 section 1 Radiation Protection Regulation) or the values given in the discharge permit. The regulation is not to be applied to installations for reactor coolant or fuel pit clean-up. (orig./HP) [de

Survey of radioactive contamination of foodstuffs

Energy Technology Data Exchange (ETDEWEB)

Lee, W. R.; Lee, C. W.; Choi, G. S.; Cho, Y. H.; Kang, M. J.; Cheong, K. H.; Kim, H. R.; Kwak, J. Y

2005-11-15

The purpose of this study is to survey and assess radioactive contamination of foodstuffs in order to reduce the probability of intake of contaminated foodstuffs. Based on survey and assessment, final goal is to improve the public health by radiation protection. Sampled foodstuffs items are collected from the markets : one group are imported foodstuffs and the other group are domestic foodstuffs producted around nuclear facilities. After pretreatments such as drying, ashing, and homogenization, all samples were analyzed by gamma spectrometer system. The {sup 137}Cs radionuclide was only measured among the regulation radionuclides ({sup 137}Cs, {sup 134}Cs, {sup 131}I) of food code. All radionuclides of the domestic foodstuffs collected around nuclear facilities were below Minimum Detectable Activity (MDA). But the activity concentrations of Inonotus obliquus (Chaga mushooms) from Russia ranged up to 171.27 (average value : 36.65) Bq/kg-fresh. In the case of blueberry jam, the radioactivity of {sup 137}Cs is higher than expected value. Other samples are below MDA except some spices. Based on the previous and present results, it should be strengthen to survey for Inontus obliquus (Chaga mushooms), of which the radioactivity shows the range from MDA up to 800.01 Bq/kg-fresh. It should assess the public radiation exposure via food chain because it has the excess provability of the maximum permitted level of food code, which is regulation of KFDA. The development method based on international standard would be used at radioactive analysis as well as education of practical workers and it could be applied as the basis data for amending the analysis method of food code. Our country only surveys gamma emitting radionuclides till now but international organization or foreign countries for example EU survey alpha and beta emitting radionuclides as well as gamma emitting radionuclides. So our country should also research necessity of survey for alpha and beta emitting

Decontaminating method for radioactive contaminant

International Nuclear Information System (INIS)

Suzuki, Ken-ichi.

1994-01-01

After decontamination of radioactive contaminates with d-limonene, a radioactive material separating agent not compatible with liquid wastes caused by decontamination is added to the liquid wastes. Then after stirring, they are stood still to be separated into two phases, and the radioactive materials in the liquid waste phase caused by decontamination are transferred to the phase of the radioactive material separating agent. With such procedures, they can satisfactorily be separated into two phases of d-limonene and the radioactive material separating agent. Further, d-limonene remaining after the separation can be used again as a decontaminating agent for radioactive contaminates. Therefore, the amount of d-limonene to be used can be reduced, to lower the cost for cleaning, thereby enabling to reduce the amount of radioactive wastes formed. (T.M.)

Radioactive contamination in imported foods (II)

International Nuclear Information System (INIS)

Kan, Kimiko; Maki, Toshio; Hashimoto, Hideki; Kawai, Yuka; Nagayama, Toshihiro; Kobayashi, Maki; Shioda, Hiroko; Nishima, Taichiro

1991-01-01

Five years have elapsed since the Chernobyl accident, but the effect of radioactivity contamination to foods has continued. Also in Japan, the imported foods which were ordered by the Ministry of Health and Welfare to be sent back due to radioactivity contamination do not cease. In fiscal year 1990, three cases occurred: tea from Albania, mushrooms from Yugoslavia and spices from france. If those are not checked at quarantines, it is feared that such foods are distributed in Japan. Among the foods which were ordered to be sent back in the past, there were those from Brazil and Hong Kong where the effect of the Chernobyl accident is little, and the foods contaminated with radioactivity spread worldwide through import and export. Therefore, attention must be paid to the foods from the countries where radioactivity contamination is little. Also it is feared that Japanese foods may be contaminated by being cultivated with imported feed, soil and fertilizer, for which there is no regulation. In this report, the radioactivity contamination of imported foods in fiscal year 1990 is described, and the experimental method and the results are reported. (K.I.)

Contained scanning electron microscope facility for examining radioactive materials

International Nuclear Information System (INIS)

Hsu, C.W.

1986-03-01

At the Savannah River Laboratory (SRL) radioactive solids are characterized with a scanning electron microscope (SEM) contained in a glove box. The system includes a research-grade Cambridge S-250 SEM, a Tracor Northern TN-5500 x-ray and image analyzer, and a Microspec wavelength-dispersive x-ray analyzer. The containment facility has a glove box train for mounting and coating samples, and for housing the SEM column, x-ray detectors, and vacuum pumps. The control consoles of the instruments are located outside the glove boxes. This facility has been actively used since October 1983 for high alpha-activity materials such as plutonium metal and plutonium oxide powders. Radioactive defense waste glasses and contaminated equipment have also been examined. During this period the facility had no safety-related incidents, and personnel radiation exposures were maintained at less than 100 mrems

Radioactive food and environment contamination

International Nuclear Information System (INIS)

Yousif, A.M.

2001-01-01

The Food and Environment Control Centre of Abu Dhabi Municipality with the help of IAEA has established facilities for regular monitoring of food and environmental samples for radioactive contamination. The Centre is now capable of measuring gamma, beta as well as alpha activity in different types of samples. The main activities in the area of food monitoring are as follows: General monitoring of food gamma radionuclides in foodstuffs by high resolution gamma spectrometry; Determination of specific gamma radionuclides in foodstuffs by high resolution gamma spectrometry; Radiochemical determination of Sr-90 using liquid scintillation analyzer or by gas flow proportional counter; Measurement of gross alpha activity in drinking water

Techniques of radioactive soil processing at rehabilitation of contamination territories - 59199

International Nuclear Information System (INIS)

Volkov, Victor; Chesnokov, Alexander; Danilovich, Alexey; Zverkov, Yury; Koltyshev, Sergey; Semenov, Sergey; Shisha, Anatoly

2012-01-01

Rehabilitation of nuclear- and radiation objects assumes dealing with and removal of considerable volumes of a radioactive soil. A similar situation was faced at the remediation of such sufficiently large objects, as old radioactive waste storages at the territory of 'Kurchatov Institute' and elimination of consequences of radiation accident at Podolsk plant of nonferrous metals. At rough estimates the volumes of a radioactive soil at territory of 'Kurchatov institute' were 15-20 thousand m 3 , volumes of a removed soil at carrying out of urgent measures in territory of Kirovo-Chepetsk chemical plant exceeded 20-25 thousand m 3 , volumes of a low active waste at the territory of Podolsk plant may reach 20 thousand m 3 . Such considerable volumes demand creation of technologies of their processing, an effective measuring technique of levels of their contamination and ways of considerable (in times) decrease of their volumes at the expense of decontamination or separation. Works have been aimed at the decision of these problems at carrying out of rehabilitation of territory 'Kurchatov institute'. During works technologies of radiation and water-gravitational separation of a radioactive soil have been offered and are realized in practice. A facility of water -gravitational separation of the soil was created and used within 5 years. It allowed decreasing of volumes of the low active waste in 5-6 times. In further the facility was supplied by a facility of radiation separation of the soil that has raised its efficiency. On turn there is a start-up question in experimental operation of facility of radiation separation of low active slag for Podolsk plant of nonferrous metals. The decision of these problems will allow to gain experience of creation of through technology of the processing of a radioactive soil and decrease in its volumes for using it as a design decisions for rehabilitation of other large scale radioactive-contaminated territories and industrial objects

Analysis of Radioactivity Contamination Level of Kartini Reactor Efluen Gas to the Environment

International Nuclear Information System (INIS)

Suratman; Purwanto; Aminjoyo, S

1996-01-01

The analysis of radioactivity contamination level of Kartini reactor efluen gas to the environment has been done from 13-10-'95 until 8-2-'96. The aim of this research is to determine the radioactivity contamination level on the environment resulted from the release of Kartini reactor efluen gas and other facilities at Yogyakarta Nuclear Research Centre through stack. The analysis methods is the student t-test, the first count factor test and the gamma spectrometry. The gas sampling were carried out in the stack reactor, reactor room, environment and in other room for comparison. Efluen gas was sucked through a filter by a high volume vacuum pump. The filter was counted for beta, gamma and alpha activities. The radioactivity contamination level of the efluen gas passing through the stack to the environment was measured between 0.57 - 1.34 Bq/m3, which was equal to the airborne radioactivity in environment between 0.69 - 1.12 Bq/m3. This radioactivity comes from radon daughter, decay products result from the natural uranium and thorium series of the materials of the building

Studies on the radioactive contamination due to nuclear detonations II. Preliminary findings on the radioactive fallout due to nuclear detonations

Energy Technology Data Exchange (ETDEWEB)

Nishiwaki, Yasushi [Nuclear Reactor Laboratory, Tokyo Institute of Technology, Tokyo (Japan); Nuclear Reactor Laboratoroy, Kinki University, Fuse City, Osaka Precture (Japan)

1961-11-25

Since we have detected a considerable amount of artificial radioactivity in the rain in spring 1954, it has become one of the most important items, from the health physics point of view, to continue measurements of radioactivity in the rain and in the atmosphere. To watch out the radioactive contamination of our environment due to repeated nuclear weapons testings in other countries was also considered to be important from the nuclear engineering point of view, in the sense that the permissible allowances of the radioactivity for the peaceful uses of atomic energy might be lowered if the degree of radioactive contamination due to nuclear testings should continue to increase gradually and indefinitely. If the permissible level were lowered, the cost for radiation protection may be expected to increase at the peaceful uses of atomic energy and should the radioactive contamination increase seriously in the future, it was anticipated that we may have to face a very difficult situation in designing the atomic energy facilities for peaceful purposes in our country. From these points of views, we have been continuing measurements of the radioactivity in the rain in Osaka, Japan since the spring of 1954. Some of the preliminary findings are introduced in this paper.

Studies on the radioactive contamination due to nuclear detonations II. Preliminary findings on the radioactive fallout due to nuclear detonations

International Nuclear Information System (INIS)

Nishiwaki, Yasushi

1961-01-01

Since we have detected a considerable amount of artificial radioactivity in the rain in spring 1954, it has become one of the most important items, from the health physics point of view, to continue measurements of radioactivity in the rain and in the atmosphere. To watch out the radioactive contamination of our environment due to repeated nuclear weapons testings in other countries was also considered to be important from the nuclear engineering point of view, in the sense that the permissible allowances of the radioactivity for the peaceful uses of atomic energy might be lowered if the degree of radioactive contamination due to nuclear testings should continue to increase gradually and indefinitely. If the permissible level were lowered, the cost for radiation protection may be expected to increase at the peaceful uses of atomic energy and should the radioactive contamination increase seriously in the future, it was anticipated that we may have to face a very difficult situation in designing the atomic energy facilities for peaceful purposes in our country. From these points of views, we have been continuing measurements of the radioactivity in the rain in Osaka, Japan since the spring of 1954. Some of the preliminary findings are introduced in this paper

Multiple methods for assessing the dose to skin exposed to radioactive contamination

International Nuclear Information System (INIS)

Dubeau, J.; Heinmiller, B.E.; Corrigan, M.

2017-01-01

There is the possibility for a worker at a nuclear installation, such as a nuclear power reactor, a fuel production facility or a medical facility, to come in contact with radioactive contaminants. When such an event occurs, the first order of business is to care for the worker by promptly initiating a decontamination process. Usually, the radiation protection personnel performs a G-M pancake probe measurement of the contamination in situ and collects part or all of the radioactive contamination for further laboratory analysis. The health physicist on duty must then perform, using the available information, a skin dose assessment that will go into the worker's permanent dose record. The contamination situations are often complex and the dose assessment can be laborious. This article compares five dose assessment methods that involve analysis, new technologies and new software. The five methods are applied to 13 actual contamination incidents consisting of direct skin contact, contamination on clothing and contamination on clothing in the presence of an air gap between the clothing and the skin. This work shows that, for the cases studied, the methods provided dose estimates that were usually within 12% (1σ) of each other, for those cases where absolute activity information for every radionuclide was available. One method, which relies simply on a G-M pancake probe measurement, appeared to be particularly useful in situations where a contamination sample could not be recovered for laboratory analysis. (authors)

Radioactive surface contamination monitors

International Nuclear Information System (INIS)

Aoyama, Kei; Minagoshi, Atsushi; Hasegawa, Toru

1994-01-01

To reduce radiation exposure and prevent contamination from spreading, each nuclear power plant has established a radiation controlled area. People and articles out of the controlled area are checked for the surface contamination of radioactive materials with surface contamination monitors. Fuji Electric has repeatedly improved these monitors on the basis of user's needs. This paper outlines typical of a surface contamination monitor, a personal surface contamination monitor, an article surface contamination monitor and a laundry monitor, and the whole-body counter of an internal contamination monitor. (author)

Internal radioactive contamination treatment

International Nuclear Information System (INIS)

Tobajas, L. M.

1998-01-01

In a radiological emergency, the internal radioactive contamination becomes a therapeutic urgency and must be established as fast as possible. Just when a radioactive contamination accident occurs, it is difficult to know exactly the amount of radioactive materials absorbed and to estimate the dose received.. The decision to be taken after the incorporation of the radioactive material depends on the method and on the Radiological Protection Department collaboration. Any treatment achieving a reduction of the doses received or expected will be useful. The International Radiological Protection Commission doesn't recommend the use of the dose limit, to decide about the intervention necessity. However the LIA can be used as the reference point to establish the necessity and reach of the treatment. The object of the present work, is to introduce the general principles to carry out the internal people decontamination, under the last international recommendations. (Author) 4 refs

Method for electrolytic decontamination of radioactive contaminated metals

International Nuclear Information System (INIS)

Tanaka, Akio; Horita, Masami; Onuma, Tsutomu; Kato, Koji

1991-01-01

The invention relates to an electrolytic decontamination method for radioactive contaminated metals. The contaminated sections are eluted by electrolysis after the surface of a piece of equipment used with radioactive substances has been immersed in an electrolyte. Metal contaminated by radioactive substances acts as the anode

Questionnaire survey report on measurement of radioactivity in working environment of radioisotopes facility

International Nuclear Information System (INIS)

Kawano, Takao; Nomura, Kiyoshi

2008-01-01

To look over the current measurement of radioactivity concentration in working environment of many radioisotopes facilities, a questionnaire survey was carried out under the auspices of the Planning Committee of the Japan Society of Radiation Safety Management. 64 responses were obtained in 128 radiation facilities, which the questionnaires were sent to. The main results were obtained by aggregate analysis of the answers for questionnaires as the followings. Major nuclides subject to measurement were 3 H, 14 C, 32 P and 125 I Sampling of radioisotopes in air was mainly performed using collectors like dust samplers and HC-collectors. Liquid scintillation counters and gamma counters were used to measure β and γ radioactivity contained in airborne particles or gas samples. Contamination by radioactivity was not detected in 55% facilities surveyed, but in 40% facilities at the same level as or at lower levels than a hundredth part of the regulated concentration limit of each nuclide. Almost all facilities is found to consider that the measurement of radioactivity concentration in working environments is not always necessary. (author)

Radioactive facilities classification criteria

International Nuclear Information System (INIS)

Briso C, H.A.; Riesle W, J.

1992-01-01

Appropriate classification of radioactive facilities into groups of comparable risk constitutes one of the problems faced by most Regulatory Bodies. Regarding the radiological risk, the main facts to be considered are the radioactive inventory and the processes to which these radionuclides are subjected. Normally, operations are ruled by strict safety procedures. Thus, the total activity of the radionuclides existing in a given facility is the varying feature that defines its risk. In order to rely on a quantitative criterion and, considering that the Annual Limits of Intake are widely accepted references, an index based on these limits, to support decisions related to radioactive facilities, is proposed. (author)

Issues facing the management of radioactively contaminated lead within the DOE system

International Nuclear Information System (INIS)

Gilmore, M.C.; Kent, S.H.

1993-01-01

The purpose of this paper is to discuss and evaluate the issues that managing and operating contractors in the US DOE system should consider that are associated with management of radioactively contaminated elemental lead. There are many instances where DOE contaminated lead fall within Resource Conservation and Recovery Act (RCRA) regulation. In light of the Federal Facilities Compliance Act (FFCA), it is becoming increasingly important for additional regulatory options to be explored in order to facilitate proper treatment, storage and disposal of RCRA regulated lead. Various DOE facilities have initiated processes to reuse or recycle contaminated lead. Technologies such as melt-refining, surface blasting, and electromigration are being explored. One or more of these technologies may be the key to reducing contaminated lead inventories in the DOE system. Many DOE facilities are finding that these efforts need to have stringent regulatory evaluation since some alternatives have proven to be environmentally desirable but not economically feasible

Radiological assessment and management of radioactive spill in a liquid waste treatment facility - Case study

International Nuclear Information System (INIS)

Amer, H.A.; Shawky, S.; Ibrahiem, N.

2002-01-01

The radiological assessment and management of radioactive spill from liquid waste treatment facility is presented. The incident contaminated the area surrounding the treatment facility with various radionuclides, which were dispersed into the soil. A method based on the European basic safety standards was used to contain the risks associated with the contaminated site. The introduced case study proceeded up to the stage of simplified risk study, since the site is small and it was relatively easy to remove and store the contaminated soil. According to the obtained results, the removal of the upper 30-cm would be considered as appropriate remedying action to resume background level. One of the most important basic concepts of radiation protection in nuclear facilities is the continuity of monitoring radiological release to the environment. It is known that from nuclear facilities only very small amounts of radioactivity are discharged with the liquid effluents and the exhaust air into the environment. Recent studies screening the natural and artificial radionuclide in soil samples from the investigated area revealed normal background concentrations with no anomalies

10 CFR 39.69 - Radioactive contamination control.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Radioactive contamination control. 39.69 Section 39.69... Radiation Safety Requirements § 39.69 Radioactive contamination control. (a) If the licensee detects evidence that a sealed source has ruptured or licensed materials have caused contamination, the licensee...

Development of Radioactive Substance Contamination Diffusion Preventive Equipment for a Hot cell

International Nuclear Information System (INIS)

Choo, Yong Sun; Kim, Do Sik; Baik, Seung Je; Yoo, Byung Ok; Kim, Ki Ha; Lee, Eun Pyo; Ahn, Sang Bok; Ryu, Woo Seok

2009-01-01

The hot cell of irradiated materials examination facility (IMEF), which has been operating since 1996, is generally contaminated by the radioactive nuclides of irradiated nuclear fuels and structural steels like Cs-137, Co-60, Co-134 and Ru-106. Especially Cs-137 is a main contaminated radioactive isotope which is easily moved here and there due to air flow in the hot cell, water-soluble, extremely toxic, and has a half-life of 30.23 years. To repair or fix the abnormal function of test apparatus installed in the hot cell, the maintenance door, so called a rear door and located at an intervention area, is opened to enter the hot cell inside. In a moment of opening the maintenance door, dirty air diffusion from the hot cell to an intervention area could be occurred in spite of increasing the rpm of exhaust fan to maintain much low under pressure, but an adjacent area to a maintenance door, i.e. intervention area, is very severely contaminated due to the unpredictable air flow. In this paper, the development of the radioactive substance contamination diffusion preventive equipment for a hot cell is studied to prevent dirty and toxic gaseous radioactive nuclides diffusion from a hot cell and installed at an intervention area of IMEF

The Calculation of Self-Disposal Date by Analyzing the Radioactive Contamination of Air Filters Disused in Radioisotope Production Facility

International Nuclear Information System (INIS)

Kim, Sung Ho; Lee, Bu Hyung; Kwon, Soo Il

2016-01-01

The aim of the study is to decrease the diffusion of air contamination which occurred in radiation work places handle radioisotope under the permissible level. Accordingly, we replaced used air filter with a new one at the appropriate time , and computed disposal dates for disposing used air filters by calculate radioactive contamination. Air filter contaminated by radioactivity is possible to be self-disposed on condition that all detected nuclides is below permissible level according to Nuclear Safety and Security Commission (NSSC) notification No. 2014-003. Radioisotope, produced by 30, 50 MeV cyclotron and carried from other institutions, is used to treat patients, diagnose diseases, and research technology in Korea Institute of Radiological and Medical Sciences (KIRAMS). With unsealed sources generate radioactive contamination in air, it is important to use fume hood or hot cell. The accurate date needs to be calculated by the equation for calculation of self disposal date. If disposal date is in 1000 days, disposal for external institution is required. With increasing the number of medical institute which was related to use the radioisotopes, the importance of radioactive safety management was increased. As disposing radioactive waste, in particular, is the procedure of inspecting for releasing radioactive waste to outside, appropriate action and continuous research are required at a radioactive safety management.

Safety assessment for radioactive waste disposal facility

International Nuclear Information System (INIS)

Thanaletchumy Karuppiah; Mohd Abdul Wahab Yusof; Nik Marzuki Nik Ibrahim; Nurul Wahida Ahmad Khairuddin

2008-08-01

Safety assessments are used to evaluate the performance of a radioactive waste disposal facility and its impact on human health and the environment. This paper presents the overall information and methodology to carry out the safety assessment for a long term performance of a disposal system. A case study was also conducted to gain hands-on experience in the development and justification of scenarios, the formulation and implementation of models and the analysis of results. AMBER code using compartmental modeling approach was used to represent the migration and fate of contaminants in this training. This safety assessment is purely illustrative and it serves as a starting point for each development stage of a disposal facility. This assessment ultimately becomes more detail and specific as the facility evolves. (Author)

Effectiveness of interim remedial actions at a radioactive waste facility

International Nuclear Information System (INIS)

Devgun, J.S.; Beskid, N.J.; Peterson, J.M.; Seay, W.M.; McNamee, E.

1989-01-01

Over the past eight years, several interim remedial actions have been taken at the Niagara Falls Storage Site (NFSS), primarily to reduce radon and gamma radiation exposures and to consolidate radioactive waste into a waste containment facility. Interim remedial actions have included capping of vents, sealing of pipes, relocation of the perimeter fence (to limit radon risk), transfer and consolidation of waste, upgrading of storage buildings, construction of a clay cutoff wall (to limit the potential groundwater transport of contaminants), treatment and release of contaminated water, interim use of a synthetic liner, and emplacement of an interim clay cap. An interim waste containment facility was completed in 1986. 6 refs., 3 figs

Radioactive Waste Management and Nuclear Facility Decommissioning Progress in Iraq - 13216

Energy Technology Data Exchange (ETDEWEB)

Al-Musawi, Fouad; Shamsaldin, Emad S.; Jasim, Hadi [Ministry of Science and Technology (MoST), Al-Jadraya, P.O. Box 0765, Baghdad (Iraq); Cochran, John R. [Sandia National Laboratories1, New Mexico, Albuquerque New Mexico 87185 (United States)

2013-07-01

Iraqi Decommissioning Directorate (IDD) is responsible for decommissioning activities. The IDD and the RWTMD work together on decommissioning projects. The IDD has developed plans and has completed decommissioning of the GeoPilot Facility in Baghdad and the Active Metallurgical Testing Laboratory (LAMA) in Al-Tuwaitha. Given this experience, the IDD has initiated work on more dangerous facilities. Plans are being developed to characterize, decontaminate and decommission the Tamuz II Research Reactor. The Tammuz Reactor was destroyed by an Israeli air-strike in 1981 and the Tammuz II Reactor was destroyed during the First Gulf War in 1991. In addition to being responsible for managing the decommissioning wastes, the RWTMD is responsible for more than 950 disused sealed radioactive sources, contaminated debris from the first Gulf War and (approximately 900 tons) of naturally-occurring radioactive materials wastes from oil production in Iraq. The RWTMD has trained staff, rehabilitated the Building 39 Radioactive Waste Storage building, rehabilitated portions of the French-built Radioactive Waste Treatment Station, organized and secured thousands of drums of radioactive waste organized and secured the stores of disused sealed radioactive sources. Currently, the IDD and the RWTMD are finalizing plans for the decommissioning of the Tammuz II Research Reactor. (authors)

Radioactive Waste Management and Nuclear Facility Decommissioning Progress in Iraq - 13216

International Nuclear Information System (INIS)

Al-Musawi, Fouad; Shamsaldin, Emad S.; Jasim, Hadi; Cochran, John R.

2013-01-01

Directorate (IDD) is responsible for decommissioning activities. The IDD and the RWTMD work together on decommissioning projects. The IDD has developed plans and has completed decommissioning of the GeoPilot Facility in Baghdad and the Active Metallurgical Testing Laboratory (LAMA) in Al-Tuwaitha. Given this experience, the IDD has initiated work on more dangerous facilities. Plans are being developed to characterize, decontaminate and decommission the Tamuz II Research Reactor. The Tammuz Reactor was destroyed by an Israeli air-strike in 1981 and the Tammuz II Reactor was destroyed during the First Gulf War in 1991. In addition to being responsible for managing the decommissioning wastes, the RWTMD is responsible for more than 950 disused sealed radioactive sources, contaminated debris from the first Gulf War and (approximately 900 tons) of naturally-occurring radioactive materials wastes from oil production in Iraq. The RWTMD has trained staff, rehabilitated the Building 39 Radioactive Waste Storage building, rehabilitated portions of the French-built Radioactive Waste Treatment Station, organized and secured thousands of drums of radioactive waste organized and secured the stores of disused sealed radioactive sources. Currently, the IDD and the RWTMD are finalizing plans for the decommissioning of the Tammuz II Research Reactor. (authors)

Development of melting facilities and techniques for decontamination and recycling of radioactively contaminated material

International Nuclear Information System (INIS)

Steinwarz, W.

1998-01-01

One decade after the accident at unit 4 of the Chernobyl nuclear power station a melting plant for radioactively contaminated metallic materials, the so-called SURF facility is being planned and licensed for erection in the direct neighbourhood of the NPP area. Main goal is the recycling of the material, largely decontaminated by the melting process, by means of manufacturing of casks and containers for waste disposal and of shielding equipment. The melting plant will be placed as part of the Ukrainian waste handling centre (CPPRO). The technology is based on the long-term experience gained at Siempelkamp's CARLA plant in Krefeld. In 1995-1997 the licensing conditions were defined, the licensing documents prepared and the formal procedure initiated. For completion of the recycling technique and to broaden the application fields for the re-usable material a granules production method has been developed and formally qualified. The essential is the substitution of the hematite portion in concrete structures providing an alternative sink for recycling material. (author)

Protection of atmospheric air against radioactive gas and aerosol contaminants

International Nuclear Information System (INIS)

Zykova, A.S.

1984-01-01

Measures for contamination protection of atmospheric air subdivided into active and passive ones, are considered. The active measures envisage: development and application of waste-free flowsheets, use of flowsheets which restrict formation of gaseous-aerosol discharges; application of highly efficient treatment facilities torage. Dispersion of radioactive substances, released with discharges to the atmosphere, using high stacks; development of the corresponding site-selection solutions and arrangement of sanitary protective zones belong to passive measures. Measures for protection of atmospheric air also include waste and air contamination monitoring. The measures described are considered as applied to NPPs

Radioactive contamination of the Guatemalan marine environment

International Nuclear Information System (INIS)

Perez-Sabino, J.F.; Oliva de Sandoval, B.E.; Orozco-Chilel, R.M.; Aguilar-Sandoval, E.

1999-01-01

As part of the IAEA TC project GUA/2/005 'Radioactivity and Contamination of the Marine Environment in Guatemala', concentrations of artificial and natural radionuclides have been determined in marine water and sediments, giving important information to establish the base line of the natural radioactivity and the radioactive contamination in this area that not have been studying

Radioactive waste and contamination in the former Soviet Union

International Nuclear Information System (INIS)

Suokko, K.; Reicher, D.

1993-01-01

Decades of disregard for the hazards of radioactive waste have created contamination problems throughout the former Soviet Union rivaled only by the Chernobyl disaster. Although many civilian activities have contributed to radioactive waste problems, the nuclear weapons program has been by far the greatest culprit. For decades, three major weapons production facilities located east of the Ural Mountains operated in complete secrecy and outside of environmental controls. Referred to until recently only by their postal abbreviations, the cities of Chelyabinsk-65, Tomsk-7, and Krasnoyarsk-26 were open only to people who worked in them. The mismanagement of waste at these sites has led to catastrophic accidents and serious releases of radioactive materials. Lack of public disclosure, meanwhile, has often prevented proper medical treatment and caused delays in cleanup and containment. 5 refs

Radioactive contamination of recycled metals

International Nuclear Information System (INIS)

Lubenau, J.O.; Cool, D.A.; Yusko, J.G.

1996-01-01

Radioactive sources commingled with metal scrap have become a major problem for the metals recycling industry worldwide. Worldwide there have been 38 confirmed reports of radioactive sources accidentally smelted with recycled metal. In some instances, contaminated metal products were subsequently distributed. The metal mills, their products and byproducts from the metal making process such as slags, crosses and dusts from furnaces can become contaminated. In the U.S., imported ferrous metal products such as reinforcement bars, pipe flanges, table legs and fencing components have been found contaminated with taco. U.S. steel mills have unintentionally smelted radioactive sources on 16 occasions. The resulting cost for decontamination waste disposal and temporary closure of the steel mill is typically USD 10,000,000 and has been as much as USD 23,000,000. Other metal recycling industries that have been affected by this problem include aluminum, copper, zinc, gold, lead and vanadium. (author)

Phytoremediation options for radioactively contaminated sites evaluated

International Nuclear Information System (INIS)

Vandenhove, Hildegarde

2013-01-01

Highlights: ► We present an overview of the most important site and environmental radioactive contamination problems encountered. ► The potential role of different phytomanagement options is discussed and illustrated with examples. ► The phytomanagement options considered are: soil phytoextraction, rhizofiltration, wetlands and alternative land use. - Abstract: The application of nuclear energy and the use of radionuclides for industrial, medical and research purposes have caused significant contamination of certain sites and their environment, which could result in health problems for several centuries if nothing is undertaken to remedy these situations. Except for the immediate environment of the facility, where decontamination activities may be feasible and affordable, the contamination often extents over a vast area and decontamination would be costly and could result in vast amounts of waste. Therefore, more realistic yet efficient remediation options should be searched for of which phytomanagement is among the potential options. A number of phytomanagement approaches will be discussed

Radioactive contamination of the Guatemalan marine environment

Energy Technology Data Exchange (ETDEWEB)

Perez-Sabino, J F; Oliva de Sandoval, B E; Orozco-Chilel, R M; Aguilar-Sandoval, E [Universidad de San Carlos de Guatemala, Facultad de Ciencias Quimicas y Farmacia, Unidad de Analisis Instrumental, Guatemala C.A. (Guatemala)

1999-07-01

As part of the IAEA TC project GUA/2/005 `Radioactivity and Contamination of the Marine Environment in Guatemala`, concentrations of artificial and natural radionuclides have been determined in marine water and sediments, giving important information to establish the base line of the natural radioactivity and the radioactive contamination in this area that not have been studying 4 refs, 1 fig., 4 tabs

Criteria for the designation of radioactively contaminated land

International Nuclear Information System (INIS)

Titley, J.; Mobbs, S.; Burgess, P.; Hitchins, G.; Sinclair, P.

1999-01-01

This report examines the criteria for the designation of radioactively contaminated land. It should be read in conjunction with reference to another output from the project i.e. Environment Agency report, Technical Support Material for the Regulation of Radioactively Contaminated Land 1999. This report deals with the intervention on radioactively contaminated sites i.e. where no change of land use is anticipated and where the land has become contaminated as a result of previous land use and not current practices. (author)

Contamination control training for biomedical facilities

International Nuclear Information System (INIS)

Trinoskey, P.A.

1994-10-01

In 1991, a contamination control course was developed for the Biology and Biotechnology Research Program (BBRP) at the Lawrence Livermore National Laboratory (LLNL). This course was based on the developer's experience in Radiation Safety at the University of Utah and University of Kansas Medical Center. This course has been well received at LLNL because it addresses issues that are important to individuals handling small quantities of radioactive materials. This group of users is often overlooked. They are typically very well educated and are expected to ''know'' what they should do. Many of these individuals are not initially comfortable working with radioactive materials. They appreciate the opportunity to be introduced to contamination control techniques and to discuss issues they may have. In addition, the authors benefit by experience that researchers bring from other facilities. The training course will address the specific radiological training requirements for chemists, biologists, and medical researchers who are using small amounts of dispersible radionuclides in tabletop experiments, and will not be exposed to other radiation sources. The training will include: the potential hazards of typical radionuclides, contamination control procedures, and guidance for developing and including site-specific information. The training course will eliminate the need for Radiological Worker II training for bio-medical researchers. The target audience for this training course is bio-medical researchers

Study of surface potential contamination in radioisotope and radiopharmaceutical production facilities and alternative solutions

International Nuclear Information System (INIS)

Suhaedi Muhammad; Rimin Sumantri; Farida Tusafariah; Djarwanti Rahayu Pipin Soedjarwo

2013-01-01

Radioisotope and radiopharmaceutical production facilities that exist in their operations around the world in the form of radiological impacts of radiation exposure, contamination of surface and air contamination. Given the number of existing open source in radioisotope and radiopharmaceutical production facility, then the possibility of surface contamination in the work area is quite high. For that to protect the safety and health of both workers, the public and the environment, then the licensee must conduct an inventory of some of the potential that could result in contamination of surfaces in radioisotope and radiopharmaceutical production facilities. Several potential to cause surface contamination in radioisotope and radiopharmaceutical production facilities consist of loss of resources, the VAC system disorders, impaired production facilities, limited resources and lack of work discipline and radioactive waste handling activities. From the study of some potential, there are several alternative solutions that can be implemented by the licensee to address the contamination of the surface so as not to cause adverse radiological impacts for both radiation workers, the public or the environment. (author)

Investigation of radioactive contamination at non-radioactive drains of the Tsuruga Nuclear Power Station

International Nuclear Information System (INIS)

Koide, Hiroaki; Imanaka, Tetsuji; Ebisawa, Toru; Kawano, Shinji; Kobayashi, Keiji.

1982-05-01

In April, 1981, it was disclosed that a drainage area at the Tsuruga Nuclear Power Station was so much contaminated with radioactivites. Although Ministry of International Trade and Industry (MITI) officially provided an explanation of a process that resulted in the contamination, many problems remain unsolved on account of insufficient and limited investigations. The authors collected mud samples from contaminated manholes and examined radioactivities in them through the measurement of #betta#- and #betta#-spectra. Chemical separation of the samples was carried out in order to obtain precise concentration of radioactive cesium. Results are as follows: i) the concentration of radioactivities does not show monotonous decrease along the stream line but an anomalous peak at downstream manholes, ii) at the manhole specified No. 6 located rather downstream, 137 Cs concentration is significantly high and the composition of radioactive nuclides is quite different from that in the other manholes, and iii) additional radioactive contamination was observed in other manholes of non-radioactive drains which would not be influenced by the accident explained by MITI. Our present work has provided much more data than by MITI and made it clear that the overall data cnnot be consistent with the simple MITI explanation; a single radioactive release accident caused the disclosed contamination. It is concluded that non-radioactive water drains at the Tsuruga Nuclear Power Station had been under continual contamination. (author)

Contamination of foods by radioactive rains

Energy Technology Data Exchange (ETDEWEB)

Obo, F; Wakamatsu, C; Nakae, Y; Higasayama, S

1955-01-01

The radioactivities of various vegetable foods contaminated by radioactive rains in May, 1954, in the Kagoshima Area were detected. Tea showed especially high radioactivities which could be extracted with hot water. Radioactive Nb, Zr, Hf, Ce, Y, Pr, and La were detected in the hot water extractions of tea by ion-exchange chromatography. The partial contribution of /sup 40/K in these radioactive vegetables was critically examined.

Volume reduction technology of radioactive waste and clearance practice of contaminated material

International Nuclear Information System (INIS)

Gao Chao

2016-01-01

• One of principles of RW management is minimization and reduction: - Advance process and facilities should be reasonably applied to reduce the waste generation (''Law of the People's Republic of China on Prevention and Control of Radioactive Pollution'', 2003); - Operator of RW storage facilities should dispose or clear up solid waste timely (''Regulations on the safety of RW management'', 2011); • Reduction principle: - Control of generation; - Use of volume reduction technique; - Clearance of slightly contaminated material

Experiments to determine the migration potential for water and contaminants in shallow land burial facilities design, emplacement, and preliminary results

International Nuclear Information System (INIS)

DePoorter, G.L.; Abeele, W.V.; Burton, B.W.

1982-01-01

Leaching and transport of radionuclides by water has been a primary mode of radioactive contamination from low-level radioactive waste disposal facilities. Similarly, the infiltration of water into nonradioactive hazardous waste disposal facilities has resulted in the movement of contaminants out of these disposal facilities. Although there have been many laboratory studies on water movement and contaminant transport, there is a need for more large scale field experiments. Large scale field experiments are necessary to (1) measure hydraulic conductivities on a scale typical of actual shallow land burial facilities and hazardous waste disposal facilities, (2) allow comparisons to be made between full scale and laboratory measurements, (3) verify the applicability of calculational methods for determining unsaturated hydraulic conductivities from water retention curves, and (4) for model validation. Experiments that will provide the information to do this are described in this paper

Protection of environmental contamination by radioactive materials and remediation of environment

International Nuclear Information System (INIS)

2003-05-01

This report consisted of the environmental contamination of radioactive and non-radioactive materials. 38 important accident examples of environmental contamination of radioactive materials in the world from 1944 to 2001 are stated. Heavily polluted areas by accidents are explained, for example, Chernobyl, atomic reactor accidents, development of nuclear weapon in USA and USSR, radioactive waste in the sea. The environmental contamination ability caused by using radioactive materials, medical use, operating reactor, disposal, transferring, crashing of airplane and artificial satellite, release are reported. It contains measurements and monitor technologies, remediation technologies of environmental contamination and separation and transmutation of radioactive materials. On the environmental contamination by non-radioactive materials, transformation of the soil contamination in Japan and its control technologies are explained. Protection and countermeasure of environmental contamination of radioactive and non-radioactive materials in Japan and the international organs are presented. There are summary and proposal in the seventh chapter. (S.Y.)

Classification of solid wastes as non-radioactive wastes

International Nuclear Information System (INIS)

Suzuki, Masahiro; Tomioka, Hideo; Kamike, Kozo; Komatu, Junji

1995-01-01

The radioactive wastes generally include nuclear fuels, materials contaminated with radioactive contaminants or neutron activation to be discarded. The solid wastes arising from the radiation control area in nuclear facilities are used to treat and stored as radioactive solid wastes at the operation of nuclear facilities in Japan. However, these wastes include many non-radioactive wastes. Especially, a large amount of wastes is expected to generate at the decommissioning of nuclear facilities in the near future. It is important to classify these wastes into non-radioactive and radioactive wastes. The exemption or recycling criteria of radioactive solid wastes is under discussion and not decided yet in Japan. Under these circumstances, the Nuclear Safety Committee recently decided the concept on the category of non-radioactive waste for the wastes arising from decommissioning of nuclear facilities. The concept is based on the separation and removal of the radioactively contaminated parts from radioactive solid wastes. The residual parts of these solid wastes will be treated as non-radioactive waste if no significant difference in radioactivity between the similar natural materials and materials removed the radioactive contaminants. The paper describes the procedures of classification of solid wastes as non-radioactive wastes. (author)

Verification of radioactive contamination surveys for practical use in biological research centres

International Nuclear Information System (INIS)

Macias, M.T.; Requejo, C.; Ruiz, M.; Pina, R.

2006-01-01

) and last but not least, the Minimum Detectable Activity (Bq cm-2) was determined for the different surveys with the above mentioned sealed sources. Finally, a data comparison was made between the calibration factors of the same monitors, supplied by different official institutions (C.I.E.M.A.T., A.U.R.P.O.). Results show no significant differences. Although, on the other hand, the Minimum Detectable Activity data obtained are below the established contamination levels in our facilities. The data in this study allows us to quantify radioactive contamination by directly applying the necessary corrections extracted from the obtained results with the tested contamination portable surveys. The actual purpose is to avoid over/underestimation of radioactive contamination that may potentially increase the personnel contamination risk. Keywords: contamination surveys, calibration, radioactive contamination, check source. (authors)

Automated methodology for estimating waste streams generated from decommissioning contaminated facilities

International Nuclear Information System (INIS)

Toth, J.J.; King, D.A.; Humphreys, K.K.; Haffner, D.R.

1994-01-01

As part of the DOE Programmatic Environmental Impact Statement (PEIS), a viable way to determine aggregate waste volumes, cost, and direct labor hours for decommissioning and decontaminating facilities is required. In this paper, a methodology is provided for determining waste streams, cost and direct labor hours from remediation of contaminated facilities. The method is developed utilizing U.S. facility remediation data and information from several decommissioning programs, including reactor decommissioning projects. The method provides for rapid, consistent analysis for many facility types. Three remediation scenarios are considered for facility D ampersand D: unrestricted land use, semi-restricted land use, and restricted land use. Unrestricted land use involves removing radioactive components, decontaminating the building surfaces, and demolishing the remaining structure. Semi-restricted land use involves removing transuranic contamination and immobilizing the contamination on-site. Restricted land use involves removing the transuranic contamination and leaving the building standing. In both semi-restricted and restricted land use scenarios, verification of containment with environmental monitoring is required. To use the methodology, facilities are placed in a building category depending upon the level of contamination, construction design, and function of the building. Unit volume and unit area waste generation factors are used to calculate waste volumes and estimate the amount of waste generated in each of the following classifications: low-level, transuranic, and hazardous waste. Unit factors for cost and labor hours are also applied to the result to estimate D ampersand D cost and labor hours

Measurement of residual radioactive surface contamination by 2-D laser heated TLD

International Nuclear Information System (INIS)

Jones, S.C.

1997-06-01

The feasibility of applying and adapting a two-dimensional laser heated thermoluminescence dosimetry system to the problem of surveying for radioactive surface contamination was studied. The system consists of a CO 2 laser-based reader and monolithic arrays of thin dosimeter elements. The arrays consist of 10,201 thermoluminescent phosphor elements of 40 micron thickness, covering a 900 cm 2 area. Array substrates are 125 micron thick polyimide sheets, enabling them to easily conform to regular surface shapes, especially for survey of surfaces that are inaccessible for standard survey instruments. The passive, integrating radiation detectors are sensitive to alpha and beta radiation at contamination levels below release guideline limits. Required contact times with potentially contaminated surfaces are under one hour to achieve detection of transuranic alpha emission at 100 dpm/100 cm 2 . Positional information obtained from array evaluation is useful for locating contamination zones. Unique capabilities of this system for survey of sites, facilities and material include measurement inside pipes and other geometrical configurations that prevent standard surveys, and below-surface measurement of alpha and beta emitters in contaminated soils. These applications imply a reduction of material that must be classified as radioactive waste by virtue of its possibility of contamination, and cost savings in soil sampling at contaminated sites

Radioactive contamination in the Arctic - Present situation and future challenges

International Nuclear Information System (INIS)

Strand, P.

2002-01-01

There is currently a focus on radioactivity and the Arctic region. The reason for this is the high number of nuclear sources in parts of the Arctic and the vulnerability of Arctic systems to radioactive contamination. The Arctic environment is also perceived as a wilderness and the need for the protection of this wilderness against contamination is great. In 1991, the International Arctic Environmental Protection Strategy (IAEPS) was launched and the Arctic Monitoring and Assessment Programme (AMAP) established. AMAP is undertaking an assessment of the radioactive contamination of the Arctic and its radiological consequences. This paper summarises some of current knowledge about sources of radioactive contamination, vulnerability, exposure of man, and potential sources for radioactive contamination within Arctic and some views on the future needs for work concerning radioactivity in Arctic. (author)

Issues in recycling and disposal of radioactively contaminated materials

International Nuclear Information System (INIS)

Kluk, A.F.; Hocking, E.K.; Roberts, R.; Phillips, J.W.

1993-01-01

The Department of Energy's present stock of potentially re-usable and minimally radioactively contaminated materials will increase significantly as the Department's remediation activities expand. As part of its effort to minimize wastes, the Department is pursuing several approaches to recover valuable materials such as nickel, copper, and steel, and reduce the high disposal costs associated with contaminated materials. Key approaches are recycling radioactively contaminated materials or disposing of them as non-radioactive waste. These approaches are impeded by a combination of potentially conflicting Federal regulations, State actions, and Departmental policies. Actions to promote or implement these approaches at the Federal, State, or Departmental level involve issues which must be addressed and resolved. The paramount issue is the legal status of radioactively contaminated materials and the roles of the Federal and State governments in regulating those materials. Public involvement is crucial in the debate surrounding the fate of radioactively contaminated materials

Radiological Risk Assessment and Survey of Radioactive Contamination for Foodstuffs

International Nuclear Information System (INIS)

Lee, W.R.; Lee, C.W.; Choi, K.S.

2007-11-01

After the Chernobyl nuclear accident in 1986, a radiological dose assessment and a survey of a radioactive contamination for foodstuffs have been investigated by many countries such as EU, Japan, USA. In the case of Japan which is similar to our country for the imported regions of foodstuffs, there were some instances of the excess for regulation on the maximum permitted levels of radioactive contamination among some imported foodstuffs. Concerns about the radioactive contamination of foodstuffs are increased because of the recently special situation (Nuclear test of North Korea). The purpose of this study is a radiological dose assessment and a survey of a radioactive contamination for foodstuffs in order to reduce the probability of intake of contaminated foodstuffs. Analytical results of the collected samples are below MDA. In this project, the model of radiological dose assessment via the food chain was also developed and radiological dose assessment was conducted based on surveys results of a radioactive contamination for foodstuffs in the Korean open markets since 2002. The results of radiological dose assessment are far below international reference level. It shows that public radiation exposure via food chain is well controlled within the international guide level. However, the radioactive contamination research of imported foodstuffs should be continuous considering the special situation(nuclear test of North Korea). These results are used to manage the radioactive contamination of the imported foodstuffs and also amend the regulation on the maximum permitted levels of radioactive contamination of foodstuffs

Incineration facility for radioactively contaminated polychlorinated biphenyls and other wastes

International Nuclear Information System (INIS)

1982-06-01

The statement assesses the environmental impacts associated with the construction of an incineration facility and related support facilities for the disposal of hazardous organic waste materials (including PCBs) which are contaminated with trace quantities of low-assay enriched uranium. The proposed action includes the incineration facility at Oak Ridge, Tennessee and storage, packaging, and shipping facilities at the Gaseous Diffusion Plants in Paducah, KY, and Portsmouth, OH; hazardous organic wastes from these plants and from the Y-12 Plant and Oak Ridge National Laboratories would be shipped to the proposed incineration facility. Impacts assessed include the effects of the project on air and water quality, on socioeconomic conditions, on public and occupational health and safety, and on ecology. Additionally, the statement presents an assessment of the potential impacts from accidents at the incineration facility or during transportation of the waste materials to the facility. The major impact identified was the potential for short-term occupational exposure to high concentrations of PCBs in smoke during the worst credible accident; mitigation of this impact will be addressed during the final design of the proposed facility. Alternatives which were assessed include no action, chemical destruction processes, and alternative transportation routes; all would have greater adverse impact or would increase the risk of an accident with the potential for adverse impact. The alternatives of commercial disposal, alternative sites, multiple incinerators, and alternative modes were eliminated from detailed analysis either because they are not feasible or because preliminary analysis showed that they would have clearly more adverse impact upon the environment than the proposed action

EP toxicity testing of lead to resolve disposition of radioactively contaminated lead

International Nuclear Information System (INIS)

Larsen, M.M.; Boehmer, A.M.

1986-03-01

The Department of Energy (DOE), in its efforts to comply with the requirements of the Resource Conservation and Recovery Act (RCRA) of 1976, is concerned with hazardous waste which is also radioactively contaminated. There are no existing facilities to treat or dispose of these wastes. One such waste is lead, which is extensively used in the nuclear industry as shielding. This paper reports the results of leach testing of lead (both solid lead samples and lead shot) to resolve questions as to whether or not radioactively contaminated waste lead must be treated as a hazardous waste. The results of these tests showed that: some samples passed the leach test. Results of development efforts performed to date to recycle lead and those planned for the future are included in this report

Method of melting decontamination of radioactive contaminated metals

International Nuclear Information System (INIS)

Uda, Tatsuhiko; Miura, Noboru; Tsuchiya, Hiroyuki.

1984-01-01

Purpose: To improve the transfer efficiency of radioactive materials into slags. Method: Contaminated metals are melt with adding slagging agent in order to transfer the radioactive materials into the slag, where the slagging agent holds less free energy than that of metal oxides contaminated with radioactive materials in order to promote the transfer of the contaminated materials into the slag layer. This effect can also be attained on metals or alloys other than iron contaminated with radioactive materials. In the case of alloy, the slagging agent is to containing such metal oxide that free energy is less than that of the oxide of metal being the main ingredient element of the alloy. The decontamination effect can further be improved by containing halogenide such as calcium fluoride together with the metal oxide into the slagging agent. (Ikeda, J.)

Environmental radioactive contamination and its control for nuclear power plants

International Nuclear Information System (INIS)

Shi Zhongqi; Qu Jingyuan; Cui Yongli

1998-01-01

The environmental radioactive releases and exposure to human being due to operation of nuclear power plants in the world and in China, environmental contamination and consequences caused by severe nuclear power plant accidents in the history, control of the radioactive contamination in China, and some nuclear laws on the radioactive contamination control established by international organizations and USA etc. are described according to literature investigation and research. Some problems and comments in radioactive contamination control for nuclear power plants in China are presented. Therefore, perfecting laws and regulations and enhancing surveillances on the contamination control are recommended

Methods for removing radioactive isotopes from contaminated streams

International Nuclear Information System (INIS)

Hoy, D.R.; Hickey, T.N.; Spulgis, I.S.; Parish, H.C.

1979-01-01

Methods for removing radioactive isotopes from contaminated gas streams for use in atmospheric containment and cleanup systems in nuclear power plants are provided. The methods provide for removal of radioactive isotopes from a first portion of the contaminated stream, separated from the remaining portion of the stream, so that adsorbent used to purify the first portion of the contaminated stream by adsorption of the radioactive isotopes therefrom can be tested to determine the adsorbing efficacy of the generally larger portion of adsorbent used to purify the remaining portion of the stream

Packaging and transportation of radioactively contaminated lead

International Nuclear Information System (INIS)

Gleason, Eugene; Holden, Gerard

2007-01-01

Under the management of the Nuclear Decommissioning Authority (NDA) the government of the United Kingdom has launched an ambitious program to remediate the nation's nuclear waste legacy. Over a twenty-five year period NDA plans to decommission several first generation nuclear power plants and other radioactive facilities. The use innovative, safe 'fit for purpose' technologies will be a major part of this complex program. This paper will present a case study of a recently completed project undertaken in support of the nuclear decommissioning activities at the Sellafield site in the United Kingdom. The focus is on an innovative application of new packaging technology developed for the safe transportation of radioactively contaminated lead objects. Several companies collaborated on the project and contributed to its safe and successful conclusion. These companies include British Nuclear Group, Gravatom Engineering, W. F. Bowker Transport, Atlantic Container Lines, MHF Logistical Solutions and Energy Solutions. New containers and a new innovative inter-modal packaging system to transport the radioactive lead were developed and demonstrated during the project. The project also demonstrated the potential contribution of international nuclear recycling activities as a safe, economic and feasible technical option for nuclear decommissioning in the United Kingdom. (authors)

Digital Autoradiography as a novel complementary technique for the investigation of radioactive contamination in nuclear facilities under dismantlement

International Nuclear Information System (INIS)

Haudebourg, Raphael; Fichet, Pascal; Goutelard, Florence

2015-01-01

The detection (location and quantification) of nuclear facilities to be dismantled possible contamination with low-range particles emitters ( 3 H, other low-energy β emitters, a emitters) remains a tedious and expensive task. Indeed, usual remote counters show a too low sensitivity to these non-penetrating radiations, while conventional wipe tests are irrelevant for fixed radioactivity evaluation. The only method to accurately measure activity levels consists in sampling and running advanced laboratory analyses (spectroscopy, liquid scintillation counting, pyrolysis...). Such measurements generally induce sample preparation, waste production (destructive analyses, solvents), nuclear material transportation, long durations, and significant labor mobilization. Therefore, the search for the limitation of their number and cost easily conflicts with the necessity to perform a dense screening for sampling (to maximize the representativeness of the samples), in installations of thousands of square meters (floors, wells, ceilings), plus furniture, pipes, and other wastes. To overcome this contradiction, Digital Autoradiography (D. A.) was re-routed from bio molecular research to radiological mapping of nuclear installations under dismantling and to waste and sample analysis. After in-situ exposure to the possibly-contaminated areas to investigate, commercial reusable radiosensitive phosphor screens (of a few 100 cm 2 ) were scanned in the proper laboratory device and sharp quantitative images of the radioactivity could be obtained. The implementation of geostatistical tools in the data processing software enabled the exhaustive characterization of concrete floors at a rate of 2 weeks / 100 m 2 , at lowest costs. Various samples such as drilled cores, or tank and wood pieces, were also successfully evaluated with this method, for decisive results. Thanks to the accurate location of potential contamination spots, this approach ensures relevant and representative sampling

Safety against radioactive contamination

International Nuclear Information System (INIS)

Anon.

1983-01-01

The ALWIT anticontamination suit is briefly described, consisting of lasting antistatic ''NDMEX III''. It was specially developed for the fire brigade who are exposed to a particular kind of contamination while carrying out radiation measurements during fire fighting, rescue and clearing up work. The ALWIT suit reliably prevents radioactive contamination of the surface of the body while wearing a breathing apparatus, independent of the ambient air. Tightly fitting cuffs on the neck, arms and legs together with zippers placed behind prevent contamination even with extreme movement. (P.F.K.)

Measures to be taken in cases of radioactive contamination of the skin

International Nuclear Information System (INIS)

Anon.

1991-01-01

This recommendation refers to those technical, medical and scientific facilities in which unsealed radioactive substances are handled. These facilities include, among other things: nuclear power plants, facilities of the fuel cycle, scientific and industrial laboratories, doctors' practices, hospitals and medical laboratories. Any unnecessary contamination of individuals shall be avoided. If contamination does occur, the resulting radiation exposure shall be kept as low as possible, even below the dose limits of the Radiological Protection Ordinance, taking into consideration the state of the art and also taking into account all circumstances pertaining to each individual case. Preventive measures to avoid or limit contamination represent the most effective form of protection. Preventive measures therefore include regular checks on the condition of the skin and constant personal skin care. Specific decontamination instructions must be provided for each individual plant and also, where applicable, for each individual workplace. Contaminated items of clothing must be removed before decontamination is commenced. Low levels of contamination can usually be eleminated in one step by washing with water. There is no need to carry out further decontamination steps where the decontamination effect is less than 10% and the remaining surface-related activity is less than 10 Bq/cm 2 (averaged over 100 cm 2 where the contamination is largely distributed over the entire area). (orig.) [de

Dose and risk assessment of norm Contaminated waste released from trench disposal facility

International Nuclear Information System (INIS)

Abdel Geleel, M.; Ramadan, A.B.; Tawfik, A.A.

2005-01-01

Oil and gas extraction and processing operations accumulate naturally occurring radioactive material (NORM) at concentrations above normal in by-product waste streams. The petroleum industry adopted methods for managing of NORM that are more restrictive than past practices and are likely to provide greater isolation of the radioactivity. Trench was used as a disposal facility for NORM contaminated wastes at one site of the petroleum industry in Egypt. The aim of this work is to calculate the risk and dose assessment received from trench disposal facility directly and after closure (1000 year). RESRAD computer code was used. The results indicated that the total effective dose (TED) received after direct closure of trench disposal facility was 7.7E-4 mSv/y while after 1000 years, it will he 3.4E-4. The health cancer risk after direct closure was 3.3E-8 while after 1000 years post closure it was 6E-8. Results of this assessment will help examine policy issues concerning different options and regulation of NORM contaminated waste generated by petroleum industry

Naturally occurring radioactive materials (NORM) in the oil and gas processing and production facilities

International Nuclear Information System (INIS)

Najera F, J.

1994-01-01

NORM contamination is produced by concentration in petroleum facilities of naturally occurring radioactive materials. The presence of NORM in petroleum reservoirs and in the oil and gas industry has been widely recognized. It's not a critical technical problem if you proceed timely to solve it. NORM is a great but controllable hazard to the human health and the environment, and represents a severe waste management problem. We suggest to the latino american oil companies to conduct studies to detect NORM contamination in their facilities an use to them to plan the appropriate actions to control the situation. (author). 15 refs

Disposal facility for radioactive wastes

International Nuclear Information System (INIS)

Utsunomiya, Toru.

1985-01-01

Purpose: To remove heat generated from radioactive wastes thereby prevent the working circumstances from being worsened in a disposal-facility for radioactive wastes. Constitution: The disposal-facility comprises a plurality of holes dug out into the ground inside a tunnel excavated for the storage of radioactive wastes. After placing radioactive wastes into the shafts, re-filling materials are directly filled with a purpose of reducing the dosage. Further, a plurality of heat pipes are inserted into the holes and embedded within the re-filling materials so as to gather heat from the radioactive wastes. The heat pipes are connected to a heat exchanger disposed within the tunnel. As a result, heating of the solidified radioactive wastes itself or the containing vessel to high temperature can be avoided, as well as thermal degradation of the re-filling materials and the worsening in the working circumstance within the tunnel can be overcome. (Moriyama, K.)

Radioactive contamination in Arctic - present situation and future challenges

International Nuclear Information System (INIS)

Strand, Per

2002-01-01

There is currently a focus on radioactivity and the Arctic region. The reason for this is probably the high number of nuclear sources in parts of the Arctic and the vulnerability of Arctic systems to radioactive contamination. The Arctic environment is also perceived as a wilderness and the need for the protection of this wilderness against contamination is great. In the last decade information has also been released concerning the nuclear situation which has caused concern in many countries. Due to such concerns, the International Arctic Environmental Protection Strategy (IAEPS) was launched in 1991 and the Arctic Monitoring and Assessment Programme (AMAP) was established. AMAP is undertaking an assessment of the radioactive contamination of the Arctic and its radiological consequences. In 1996 IAEPS became part of the Arctic Council. AMAP presented one main report in 1997 and another in 1998. There are also several other national, bilateral and international programmes in existence which deal with this issue. This paper summarises some of current knowledge about sources of radioactive contamination, vulnerability, exposure of man, and potential sources for radioactive contamination within Arctic and some views on the future needs for work concerning radioactivity in Arctic. (au)

An autoradiographical method using an imaging plate for the analyses of plutonium contamination in a plutonium handling facility

International Nuclear Information System (INIS)

Takasaki, Koji; Sagawa, Naoki; Kurosawa, Shigeyuki; Mizuniwa, Harumi

2011-01-01

An autoradiographical method using an imaging plate (IP) was developed to analyze plutonium contamination in a plutonium handling facility. The IPs were exposed to ten specimens having a single plutonium particle. Photostimulated luminescence (PSL) images of the specimens were taken using a laser scanning machine. One relatively large spot induced by α-radioactivity from plutonium was observed in each PSL image. The plutonium-induced spots were discriminated by a threshold derived from background and the size of the spot. A good relationship between the PSL intensities of the spots and α-radioactivities measured using a radiation counter was obtained by least-square fitting, taking the fading effect into consideration. This method was applied to workplace monitoring in an actual uranium-plutonium mixed oxide (MOX) fuel fabrication facility. Plutonium contaminations were analyzed in ten other specimens having more than two plutonium spots. The α-radioactivities of plutonium contamination were derived from the PSL images and their relative errors were evaluated from exposure time. (author)

Measurement of radioactivity in contaminated crops

Energy Technology Data Exchange (ETDEWEB)

Yamada, Y; Hasegawa, M; Kihara, T

1956-01-01

A method called the Direct Method was developed to correct for natural /sup 40/K radiation in plant samples. The K content of the ashed sample is determined by flamephotometry. The radioactivity in a 100 mg sample is measured and the natural radioactivity from /sup 40/K determined by calculation subtracted. Tea samples tested gave evidence of contamination by radioactive fallout.

Process for reducing radioactive contamination in phosphogypsum

International Nuclear Information System (INIS)

Palmer, J.W.; Gaynor, J.C.

1983-01-01

In a process for reducing radioactive contamination of phosphogypsum, anhydrite crystals are obtained through dehydration of the phosphogypsum in strong sulfuric acid: a portion of the anhydrite crystals is converted to subtantially radiation free gypsum by crystallizing out on radiation free gypsum seed crystals. These coarse radiation free gypsum crystals are then separated from the small anhydrite crystal relics containing substantially all of the radioactive contamination

Phytoremediation of water bodies contaminated with radioactive heavy metal

International Nuclear Information System (INIS)

Yan Zhen; Yuan Shichao; Ling Hui; Xie Shuibo

2012-01-01

The sources of the radioactive heavy metal in the water bodies were analyzed. The factors that affect phyto remediation of water contaminated with radioactive heavy metal were discussed. The plant species, mechanism and major technology of phyto remediation of water contaminated with radioactive heavy metal were particularly introduced. The prospective study was remarked. (authors)

Characteristics of radioactive contamination of vegetables derived from the Fukushima nuclear accident

International Nuclear Information System (INIS)

Shiba, Kazuhiro; Kitamura, Yoji; Kozaka, Takashi; Uno, Izumi; Shimizu, Kikuo; Hirota, Masahiro; Higaki, Shogo; Masumoto, Kazuyoshi

2012-01-01

We examined the characteristics of the radioactive contamination and the physical removal of radioactivity from contaminated cabbage and spinach. In a distribution imaging study, there were two types of contamination, spot type and spread type, of cabbage and spinach. The relative radioactivity (PSL) of the face of the leaf was much higher than that of the back of a leaf of cabbage. The ratio of relative radioactivity (PSL) between spot contamination and spread contamination in a leaf of spinach was 9.4% and 90.6%, respectively. More than 80% of radioactivity attaches to the surface of leaves of spinach. There was no significant difference of radioactivity removal between hand-washing and rinsing with running water. The degree of removal of radioactivity from contaminated spinach depended on the length of time between contamination and rinsing. When contaminated spinach was rinsed within 1 week after contamination, the removal ratio of 131 I and 137 Cs was high, with 50% and 70%, respectively. When rinsing contaminated spinaches more than 2 weeks after contamination, the removal ratio of 131 I and 137 Cs was low, approximately 34% and 69%, respectively. (author)

Planning for environmental restoration of radioactively contaminated sites in central and eastern Europe. V.1: Identification and characterization of contaminated sites. Proceedings of a workshop held within the technical co-operation project

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The radioactive contaminant materials resulting from diverse activities in relation to the nuclear fuel cycle, defense related operations, and various industries in addition to medical and research facilities represent perhaps the most severe and immense pollution left from a past era. The political changes in central and eastern Europe (CEE) not only brought some disclosure of the radioactively contaminated sites, but also resulted in a political condition in which this region became receptive to co-operation from a range of outside countries. The subject of the first workshop held in Budapest, 4-8 October 1993, was the identification and characterization of radioactively contaminated sites in the region. Refs, figs and tabs.

Planning for environmental restoration of radioactively contaminated sites in central and eastern Europe. V.1: Identification and characterization of contaminated sites. Proceedings of a workshop held within the technical co-operation project

International Nuclear Information System (INIS)

1996-02-01

The radioactive contaminant materials resulting from diverse activities in relation to the nuclear fuel cycle, defense related operations, and various industries in addition to medical and research facilities represent perhaps the most severe and immense pollution left from a past era. The political changes in central and eastern Europe (CEE) not only brought some disclosure of the radioactively contaminated sites, but also resulted in a political condition in which this region became receptive to co-operation from a range of outside countries. The subject of the first workshop held in Budapest, 4-8 October 1993, was the identification and characterization of radioactively contaminated sites in the region. Refs, figs and tabs

Process for reducing radioactive contamination in waste product gypsum

International Nuclear Information System (INIS)

Lange, P.H. Jr.

1979-01-01

A process is described for reducing the radioactive contamination in waste product gypsum in which waste product gypsum is reacted with a dilute sulfuric acid containing barium sulfate to form an acid slurry at an elevated temperature, the slurry is preferably cooled, the acid component is separated from the solid, and the resulting solid is separated into a fine fraction and a coarse fraction. The fine fraction predominates in barium sulfate and radioactive contamination. The coarse fraction predominates in a purified gypsum product of reduced radioactive contamination

Establishing community trust at radioactively contaminated sites

International Nuclear Information System (INIS)

Simpson, E.

1999-01-01

Establishing community trust is an essential element in the successful remediation of a radioactively contaminated site. The US Environmental Protection Agency (EPA), Region 2 has been involved in the clean up of numerous radioactively contaminated Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), Resource Conservation Recovery Act (RCRA), and Formerly Utilized Site Remedial Action Program (FUSRAP) sites in New Jersey and New York. Each site presented a unique challenge which centered around establishing and, often, re-establishing the trust of the surrounding community. Thanks to the United States government's history regarding the use of radioactive materials, people question whether governmental regulators could possibly have the public's best interests in mind when it comes to addressing radioactively contaminated sites. It has been our experience that EPA can use its position as guardian of the environment to help establish public confidence in remedial actions. The EPA can even use its position to lend credibility to remedial activities in situations where it is not directly responsible for the clean-up. Some ways that we have found to instill community confidence are: establishing radioanalytical cross-check programs using EPA's National Air and Radiation Environmental Laboratory to provide analytical quality assurance; and establishing an environmental radiation monitoring program for the contaminated site and surrounding community. (author)

[Assessment of cyto- and genotoxicity of natural waters in the vicinity of radioactive waste storage facility using Allium-test].

Science.gov (United States)

Udalova, A A; Geras'kin, S A; Dikarev, V G; Dikareva, N S

2014-01-01

Efficacy of bioassays of "aberrant cells frequency" and "proliferative activity" in root meristem of Allium cepa L. is studied in the present work for a cyto- and genotoxicity assessment of natural waters contaminated with 90Sr and heavy metals in the vicinity of the radioactive waste storage facility in Obninsk, Kaluga region. The Allium-test is shown to be applicable for the diagnostics of environmental media at their combined pollution with chemical and radioactive substances. The analysis of aberration spectrum shows an important role of chemical toxicants in the mutagenic potential of waters collected in the vicinity of the radioactive waste storage facility. Biological effects are not always possible to explain from the knowledge on water contamination levels, which shows limitations of physical-chemical monitoring in providing the adequate risk assessment for human and biota from multicomponent environmental impacts.

Radioactive material inventory control at a waste characterization facility

International Nuclear Information System (INIS)

Yong, L.K.; Chapman, J.A.; Schultz, F.J.

1996-01-01

Due to the recent introduction of more stringent Department of Energy (DOE) regulations and requirements pertaining to nuclear and criticality safety, the control of radioactive material inventory has emerged as an important facet of operations at DOE nuclear facilities. In order to comply with nuclear safety regulations and nuclear criticality requirements, radioactive material inventories at each nuclear facility have to be maintained below limits specified for the facility in its safety authorization basis documentation. Exceeding these radioactive material limits constitutes a breach of the facility's nuclear and criticality safety envelope and could potentially result in an accident, cause a shut-down of the facility, and bring about imminent regulatory repercussions. The practice of maintaining control of radioactive material, especially sealed and unsealed sources, is commonplace and widely implemented; however, the requirement to track the entire radioactivity inventory at each nuclear facility for the purpose of ensuring nuclear safety is a new development. To meet the new requirements, the Applied Radiation Measurements Department at Oak Ridge National Laboratory (ORNL) has developed an information system, called the open-quotes Radioactive Material Inventory Systemclose quotes (RMIS), to track the radioactive material inventory at an ORNL facility, the Waste Examination and Assay Facility (WEAF). The operations at WEAF, which revolve around the nondestructive assay and nondestructive examination of waste and related research and development activities, results in an ever-changing radioactive material inventory. Waste packages and radioactive sources are constantly being brought in or taken out of the facility; hence, use of the RMIS is necessary to ensure that the radioactive material inventory limits are not exceeded

The Barents Sea, distribution and fate of radioactive contaminants

International Nuclear Information System (INIS)

Foeyn, L.; Heldal, H.E.; Svaeren, I.

1999-01-01

Possible contamination in the marine food webs of the Barents Sea may be a problem for a rational harvest of the area. Radioactive contamination has in this context a special public impact as even traces of radioactivity seems to be considered by the public to be a real danger. It is therefor of special importance, from a regulatory and fisheries point of view, to accumulate knowledge of the behaviour of radioactive elements in the marine ecosystems of the Barents Sea in order to place this contamination in proper and realistic proportions

Legislative and Regulatory Control for the Safety of Radioactively Contaminated Scrap Metals Generated from Mining and Mineral Processing Facilities in South Africa

Energy Technology Data Exchange (ETDEWEB)

Mohajane, E. P.; Shale, K., E-mail: PEMohajane@nnr.co.za [National Nuclear Regulator, Centurion, Gauteng (South Africa)

2011-07-15

In South Africa, enhanced levels of naturally occurring radioactive materials (NORM) are associated with many mining and industrial processes. Significant amounts of waste materials are involved which can result in radiation exposure of the workers and the public particularly through the diversion of materials into the public domain. The following operations have been regulated in South Africa for the past twenty years: operating metallurgical plants utilizing NORM, underground mining operations, scrap recyclers and smelters, and rehabilitation and remediation activities involving the above sites. The radioactively contaminated scrap metal generated from the above mentioned facilities is available for recycling in amounts of thousands of tons. The South African government has, to a certain extent, responded to the above-mentioned challenges by introducing regulatory controls to the affected industries. The existing regulatory controls have, however, not provided absolute answers to all issues associated with the management of scrap. (author)

Contamination of fodder and radioactivity in turkeys

International Nuclear Information System (INIS)

Kossakowski, S.; Olszewska, K.

1985-01-01

Radioactivity was determined in mixed fodder (IB, IC, IE) and in turkeys which were given that feeding stuff. In animals (25 males and 25 females) fed with the above mixed fodder for 16-24 weeks radioactivity was assessed in internal organs and in their tissues. It was found that radioactivity ranged from 322.2 Bq/kg to 190.6 Bq/kg. In males the highest contamination was found in the spleen (average 0.108 Bq/g), in skeletal muscles (0.082 Bq/g), and in the liver (0.080 Bq/g), and the lowest in the skin (0.046 Bq per 1 g). The findings indicate that radioactivity of carcasses and internal organs in turkeys fed with contamined fodder was much lower than that in fodder. 6 refs., 1 tab. (author)

Radioactive contamination mapping system detailed design report

International Nuclear Information System (INIS)

Bauer, R.G.; O'Callaghan, P.B.

1996-08-01

The Hanford Site's 100 Area production reactors released radioactively and chemically contaminated liquids into the soil column. The primary source of the contaminated liquids was reactor coolant and various waste waters released from planned liquid discharges, as well as pipelines, pipe junctions, and retention basins leaking into the disposal sites. Site remediation involves excavating the contaminated soils using conventional earthmoving techniques and equipment, treating as appropriate, transporting the soils, and disposing the soils at ERDF. To support remediation excavation, disposal, and documentation requirements, an automated radiological monitoring system was deemed necessary. The RCMS (Radioactive Contamination Mapping System) was designed to fulfill this need. This Detailed Design Report provides design information for the RCMS in accordance with Bechtel Hanford, Inc. Engineering Design Project Instructions

Experimental study of radioactive aerosols emission during the thermal degradation of organic materials in nuclear facilities

International Nuclear Information System (INIS)

Fernandez, Yvette

1993-01-01

Radioactive products may be released during a fire in nuclear fuel cycles facilities. These products must be confined to avoid a contamination spread in the environment. It is therefore necessary to be able to predict the amount and the physico-chemical forms of radioactive material that may be airborne. The aim of this study is to determine experimentally the release of contamination aerosols in a typical fire scenario involving plutonium oxide in a glove box. Firstly, this phenomenon has been studied in a small scale test chamber where samples of polymethylmethacrylate (Plexiglas) contaminated by cerium oxide (used as a substitute for plutonium oxide) were submitted to thermal degradation (pyrolysis and combustion). The release of radioactive material is determined by the quantity of contaminant emitted, the kinetics of the release and the particle size distribution of aerosols. Secondly, the development of an experimental procedure allowed to realize large scale fires in more realistic conditions. The experimental tools developed in the course of this study allow to consider application to other scenarios. (author) [fr

Technologies for remediation of radioactively contaminated sites

International Nuclear Information System (INIS)

1999-06-01

This report presents particulars on environmental restoration technologies (control and treatment) which can be applied to land based, radioactively contaminated sites. The media considered include soils, groundwater, surface water, sediments, air, and terrestrial and aquatic vegetation. The technologies addressed in this report can be categorized as follows: self-attenuation (natural restoration); in-situ treatment; removal of contamination; ex-situ treatment; and transportation and final disposal. The report provides also background information about and a general approach to remediation of radioactively contaminated sites as well as some guidance for the selection of a preferred remediation technology. Examples of remediation experience in Australia and Canada are given it annexes

Technologies for remediation of radioactively contaminated sites

Energy Technology Data Exchange (ETDEWEB)

1999-06-01

This report presents particulars on environmental restoration technologies (control and treatment) which can be applied to land based, radioactively contaminated sites. The media considered include soils, groundwater, surface water, sediments, air, and terrestrial and aquatic vegetation. The technologies addressed in this report can be categorized as follows: self-attenuation (natural restoration); in-situ treatment; removal of contamination; ex-situ treatment; and transportation and final disposal. The report provides also background information about and a general approach to remediation of radioactively contaminated sites as well as some guidance for the selection of a preferred remediation technology. Examples of remediation experience in Australia and Canada are given it annexes Refs, figs, tabs

Radioactive Waste Management and Environmental Contamination Issues at the Chernobyl Site

International Nuclear Information System (INIS)

Napier, Bruce A.; Schmieman, Eric A.; Voitsekhovitch, Oleg V.

2007-01-01

The destruction of the Unit 4 reactor at the Chernobyl Nuclear Power Plant resulted in the generation of radioactive contamination and radioactive waste at the site and in the surrounding area (referred to as the Exclusion Zone). In the course of remediation activities, large volumes of radioactive waste were generated and placed in temporary near surface waste-storage and disposal facilities. Trench and landfill type facilities were created from 1986 to 1987 in the Chernobyl Exclusion Zone at distances 0.5 to 15 km from the NPP site. This large number of facilities was established without proper design documentation, engineered barriers, or hydrogeological investigations and they do not meet contemporary waste-safety requirements. Immediately following the accident, a Shelter was constructed over the destroyed reactor; in addition to uncertainties in stability at the time of its construction, structural elements of the Shelter have degraded as a result of corrosion. The main potential hazard of the Shelter is a possible collapse of its top structures and release of radioactive dust into the environment. A New Safe Confinement (NSC) with a 100-years service life is planned to be built as a cover over the existing Shelter as a longer-term solution. The construction of the NSC will enable the dismantlement of the current Shelter, removal of highly radioactive, fuel-containing materials from Unit 4, and eventual decommissioning of the damaged reactor. More radioactive waste will be generated during NSC construction, possible Shelter dismantling, removal of fuel containing materials, and decommissioning of Unit 4. The future development of the Exclusion Zone depends on the future strategy for converting Unit 4 into an ecologically safe system, i.e., the development of the NSC, the dismantlement of the current Shelter, removal of fuel containing material, and eventual decommissioning of the accident site. To date, a broadly accepted strategy for radioactive waste

Radioactive waste management and environmental contamination issues at the Chernobyl site.

Science.gov (United States)

Napier, B A; Schmieman, E A; Voitsekovitch, O

2007-11-01

The destruction of the Unit 4 reactor at the Chernobyl Nuclear Power Plant resulted in the generation of radioactive contamination and radioactive waste at the site and in the surrounding area (referred to as the Exclusion Zone). In the course of remediation activities, large volumes of radioactive waste were generated and placed in temporary near-surface waste storage and disposal facilities. Trench and landfill type facilities were created from 1986-1987 in the Chernobyl Exclusion Zone at distances 0.5-15 km from the nuclear power plant site. This large number of facilities was established without proper design documentation, engineered barriers, or hydrogeological investigations and they do not meet contemporary waste-safety requirements. Immediately following the accident, a Shelter was constructed over the destroyed reactor; in addition to uncertainties in stability at the time of its construction, structural elements of the Shelter have degraded as a result of corrosion. The main potential hazard of the Shelter is a possible collapse of its top structures and release of radioactive dust into the environment. A New Safe Confinement (NSC) with a 100 y service life is planned to be built as a cover over the existing Shelter as a longer-term solution. The construction of the NSC will enable the dismantlement of the current Shelter, removal of highly radioactive, fuel-containing materials from Unit 4, and eventual decommissioning of the damaged reactor. More radioactive waste will be generated during NSC construction, possible Shelter dismantling, removal of fuel-containing materials, and decommissioning of Unit 4. The future development of the Exclusion Zone depends on the future strategy for converting Unit 4 into an ecologically safe system, i.e., the development of the NSC, the dismantlement of the current Shelter, removal of fuel-containing material, and eventual decommissioning of the accident site. To date, a broadly accepted strategy for radioactive waste

Efficient handling of high-level radioactive cell waste in a vitrification facility analytical laboratory

International Nuclear Information System (INIS)

Roberts, D.W.; Collins, K.J.

1998-01-01

The Savannah River Site''s (SRS) Defense Waste Processing Facility (DWPF) near Aiken, South Carolina, is the world''s largest and the United State''s first high level waste vitrification facility. For the past 1.5 years, DWPF has been vitrifying high level radioactive liquid waste left over from the Cold War. The vitrification process involves the stabilization of high level radioactive liquid waste into borosilicate glass. The glass is contained in stainless steel canisters. DWPF has filled more than 200 canisters 3.05 meters (10 feet) long and 0.61 meters (2 foot) diameter. Since operations began at DWPF in March of 1996, high level radioactive solid waste continues to be generated due to operating the facility''s analytical laboratory. The waste is referred to as cell waste and is routinely removed from the analytical laboratories. Through facility design, engineering controls, and administrative controls, DWPF has established efficient methods of handling the high level waste generated in its laboratory facility. These methods have resulted in the prevention of undue radiation exposure, wasted man-hours, expenses due to waste disposal, and the spread of contamination. This level of efficiency was not reached overnight, but it involved the collaboration of Radiological Control Operations and Laboratory personnel working together to devise methods that best benefited the facility. This paper discusses the methods that have been incorporated at DWPF for the handling of cell waste. The objective of this paper is to provide insight to good radiological and safety practices that were incorporated to handle high level radioactive waste in a laboratory setting

Assessment of potential risk of environmental radioactive contamination in northern Europe from terrestrial nuclear units in north-west Russia

International Nuclear Information System (INIS)

Lisovsky, I.; Baklanov, A.; Jacovlev, V.; Prutskov, V.; Bergman, R.

1999-05-01

This Technical Report, being part of the INTAS project 96-1802, constitutes a comprehensive presentation - covering basic results from separate contributions as specified below - of work performed during the first period (February 1998- February 1999). The aim of the INTAS project 96-1802: 'Assessment of potential risk of environmental radioactive contamination in northern Europe from terrestrial nuclear units in north-west Russia' is to assess the potential risk of environmental radioactive contamination from nuclear units in north-west Russia and resulting impacts on population and terrestrial ecosystems in the north. The work focuses mainly on airborne radioactive contamination, but some case studies also deal with accidental leakage from terrestrial nuclear sites to soil and coastal waters. The present material comprises in more detail the contributions from participants no.4 and no.5 based on the four internal reports referred to below: (1) Assessment of potential risk of environmental radioactive contamination in Northern Europe from terrestrial nuclear units in north-west Russia: 'Determination of the list of typical sources of danger emergency radioactive releases in an environment in connection with military activity in the North of Russia.' Technical report no.1 of the team no.5. St.-Petersburg State Technical University, St.-Petersburg. July 1998. 43 p.; (2) Assessment of potential risk of environmental radioactive contamination in Northern Europe from terrestrial nuclear units in North-west Russia: 'Analysis and description of source-term characteristics for accident linked with airborne radioactive releases from Kola Nuclear Power Plant. Establishing a network facility at INEP for communication among the INTAS Project participants.' Technical report no.1 of the team no.4. Kola Science Centre, Apatity. August 1998. 56 p.; (3) Assessment of potential risk of environmental radioactive contamination in Northern Europe from terrestrial nuclear units in

Assessment of potential risk of environmental radioactive contamination in northern Europe from terrestrial nuclear units in north-west Russia

Energy Technology Data Exchange (ETDEWEB)

Lisovsky, I. [St. Petersburg State Technical Univ. (Russian Federation); Baklanov, A. [Inst. of the Northern Ecology Problems (INEP) (Russian Federation); Jacovlev, V. [St. Petersburg State Technical Univ. (Russian Federation); Prutskov, V. [Ministry of Defence (Russian Federation). First Central Research Inst. of Naval Shipbuilding; Tarasov, I. [Ministry of Defence (Russian Federation). 23 State Marine Project Inst.; Blecher, A. [State Unitary Enterprise (Russian Federation). Research Inst. of Industrial and Marine Medicine; Zvonariev, B.; Kuchin, N.; Rubanov, S.; Sergeiev, I. [State Scientific Centre (Russian Federation). Central Research Inst. of A. Krylov; Morozov, S.; Koshkin, V.; Fedorenko, Yu.; Rigina, O. [Inst. of the Northern Ecology Problems (INEP) (Russian Federation); Bergman, R. [ed.] [Defence Research Establishment, Umeaa (Sweden). Div. of NBC Defence

1999-05-01

This Technical Report, being part of the INTAS project 96-1802, constitutes a comprehensive presentation - covering basic results from separate contributions as specified below - of work performed during the first period (February 1998- February 1999). The aim of the INTAS project 96-1802: `Assessment of potential risk of environmental radioactive contamination in northern Europe from terrestrial nuclear units in north-west Russia` is to assess the potential risk of environmental radioactive contamination from nuclear units in north-west Russia and resulting impacts on population and terrestrial ecosystems in the north. The work focuses mainly on airborne radioactive contamination, but some case studies also deal with accidental leakage from terrestrial nuclear sites to soil and coastal waters. The present material comprises in more detail the contributions from participants no.4 and no.5 based on the four internal reports referred to below: (1) Assessment of potential risk of environmental radioactive contamination in Northern Europe from terrestrial nuclear units in north-west Russia: `Determination of the list of typical sources of danger emergency radioactive releases in an environment in connection with military activity in the North of Russia.` Technical report no.1 of the team no.5. St.-Petersburg State Technical University, St.-Petersburg. July 1998. 43 p.; (2) Assessment of potential risk of environmental radioactive contamination in Northern Europe from terrestrial nuclear units in North-west Russia: `Analysis and description of source-term characteristics for accident linked with airborne radioactive releases from Kola Nuclear Power Plant. Establishing a network facility at INEP for communication among the INTAS Project participants.` Technical report no.1 of the team no.4. Kola Science Centre, Apatity. August 1998. 56 p.; (3) Assessment of potential risk of environmental radioactive contamination in Northern Europe from terrestrial nuclear units in

Released radioactivity reducing facility

International Nuclear Information System (INIS)

Tanaka, Takeaki.

1992-01-01

Upon occurrence of a reactor accident, penetration portions of a reactor container, as a main leakage source from a reactor container, are surrounded by a plurality of gas-tight chambers, the outside of which is surrounded by highly gas-tightly buildings. Branched pipelines of an emergency gas processing system are introduced to each of the gas-tight chambers and they are joined and in communication with an emergency gas processing device. With such a constitution, radioactive materials are prevented from leaking directly from the buildings. Further, pipeline openings of the emergency gas processing facility are disposed in the plurality highly gas-tight penetration chambers. If the radioactive materials are leaked from the reactor to elevate the pressure in the penetration chambers, the radioactive materials are introduced to a filter device in the emergency gas processing facility by way of the branched pipelines, filtered and then released to the atmosphere. Accordingly, the reliability and safety of the system can be improved. (T.M.)

Management of commercial high-level and transuranium-contaminated radioactive wastes. Environmental statement

International Nuclear Information System (INIS)

1974-09-01

This Draft Environmental Statement is issued to assess the environmental impact of the AEC's program to manage commercial high-level and transuranium-contaminated radioactive wastes. These are the types of commercial radioactive wastes for which AEC custody is required by present or anticipated regulations. The program consists of three basic parts: development of a Retrievable Surface Storage Facility (RSSF) for commercial high-level waste, using existing technology; evaluating geological formations and sites for the development of a Geological Disposal Pilot Plant (GDPP) which would lead to permanent disposal; and providing retrievable storage for the transuranium-contaminated waste pending availability of permanent disposal. Consideration has been given to all environmental aspects of the program, using waste generation projections through the year 2000. Radiological and other impacts of implementing the program are expected to be minimal, but will be discussed in further environmental statements which will support budget actions for specific repositories. The alternatives discussed in this Draft Environmental Statement are presented. (U.S.)

Engineering study for a melting, casting, rolling and fabrication facility for recycled contaminated stainless steel

International Nuclear Information System (INIS)

1994-01-01

This Preliminary Report is prepared to study the facilities required for recycling contaminated stainless steel scrap into plate which will be fabricated into boxes suitable for the storage of contaminated wastes and rubble. The study is based upon the underlying premise that the most cost effective way to produce stainless steel is to use the same processes employed by companies now in production of high quality stainless steel. Therefore, the method selected for this study for the production of stainless steel plate from scrap is conventional process using an Electric Arc Furnace for meltdown to hot metal, a Continuous Caster for production of cast slabs, and a Reversing Hot Mill for rolling the slabs into plate. The fabrication of boxes from the plate utilizes standard Shears, Punch Presses and welding equipment with Robotic Manipulators. This Study presumes that all process fumes, building dusts and vapors will be cycled through a baghouse and a nuclear grade HEPA filter facility prior to discharge. Also, all process waste water will be evaporated into the hot flue gas stream from the furnace utilizing a quench tank; so there will be no liquid discharges from the facility and all vapors will be processed through a HEPA filter. Even though HEPA filters are used today in controlling radioactive contamination from nuclear facilities there is a sparsity of data concerning radioactivity levels and composition of waste that may be collected from contaminated scrap steel processing. This report suggests some solutions to these problems but it is recommended that additional study must be given to these environmental problems

Assessment of sites concerning radioactive contamination during preparation of a Contamination Site Register

International Nuclear Information System (INIS)

Gellermann, Rainer; Flesch, Klaus

2014-01-01

Experience gained since 1990 in the new, but also old German Federal States has shown that there are radioactive contaminated sites beside the legacies of uranium mining in Germany which caused exposures exceeding the radiation protection limits for members of the public. The reason for this situation is that radioactivity has been excluded in the compilation of the register for potentially hazardous sites that are prepared routinely in the context of soil protection assessments. Moreover, the information contained in these registers is not yet evaluated regarding aspects of radioactivity. In many cases, the information existing at the soil protection authorities needs only to be additionally filtered in order to identify potentially hazardous sites for radioactive contamination. For that reason, the working group ''Natural radioactivity'' (AKNAT) of the German-Swiss Radiation Protection Association developed a specific catalogue of business branches that provides indications for radioactive legacies.

Status of Activities on Rehabilitation Of Radioactively Contaminated Facilities and the Site of Russian Research Center ''Kurchatov Institute''

International Nuclear Information System (INIS)

Volkov, V. G.; Ponomarev-Stepnoi, N. N.; Melkov, E. S; Ryazantsev, E. P.; Dikarev, V. S.; Gorodetsky, G. G.; Zverkov, Yu. A.; Kuznetsov, V. V.; Kuznetsova, T. I.

2003-01-01

This paper describes the program, the status, and the course of activities on rehabilitation of radioactively contaminated facilities and the territory of temporary radioactive waste (radwaste) disposal at the Russian Research Center ''Kurchatov Institute'' (RRC KI) in Moscow as performed in 2001-2002. The accumulation of significant amounts of radwaste at RRC KI territory is shown to be the inevitable result of Institute's activity performed in the days of former USSR nuclear weapons project and multiple initial nuclear power projects (performed from 1950's to early 1970's). A characterization of RRC KI temporary radwaste disposal site is given. Described is the system of radiation control and monitoring as implemented on this site. A potential hazard of adverse impacts on the environment and population of the nearby housing area is noted, which is due to possible spread of the radioactive plume by subsoil waters. A description of the concept and project of the RRC KI temporary radwaste disposal site is presented. Specific nature of the activities planned and performed stems from the nearness of housing area. This paper describes main stages of the planned activities for rehabilitation, their expected terms and sources of funding, as well as current status of the project advancement. Outlined are the problems faced in the performance and planning of works. The latter include: diagnostics of the concrete-grouted repositories, dust-suppression technologies, packaging of the fragmented ILW and HLW, soil clean-up, radioactive plume spread prevention, broad radiation monitoring of the work zone and environment in the performance of rehabilitation works. Noted is the intention of RRC KI to establish cooperation with foreign, first of all, the U.S. partners for the solution of problems mentioned above

Comparison of public exposures from different sources of radioactive contamination in recent years in Slovenia

International Nuclear Information System (INIS)

Vokal, B.; Krizman, M.

2003-01-01

In spite of that Slovenia is a small country it contains a considerable variety of radioactive sources, which cause radioactive contamination of the environment. These sources mostly belong to nuclear fuel cycle, as the Krsko Nuclear Power Plant, the Zirovski vrh Uranium Mine (in the decommissioning), the TRIGA Research Reactor and Central low and intermediate level radioactive waste storage. Some other technological enhanced natural radiation sources, for example, the Sostanj Thermal Power Plant have also an impact to the environment. The comparison of the public exposure due to various sources of radioactive releases to the exposure of a members of the public in Slovenia shows that the critical group in the vicinity of the Zirovski Vrh uranium mine is the most exposed one in Slovenia. The global contamination due to the Chernobyl accident and the past nuclear tests was estimated to be around 10 μSv in Slovenia while the estimated annual dose for all other radioactive facilities are in the order of magnitude of one μSv. In this review the releases from the hospitals are not reported but some studies showed that it is not negligible. (authors)

Radioactive waste management from nuclear facilities

International Nuclear Information System (INIS)

2005-06-01

This report has been published as a NSA (Nuclear Systems Association, Japan) commentary series, No. 13, and documents the present status on management of radioactive wastes produced from nuclear facilities in Japan and other countries as well. Risks for radiation accidents coming from radioactive waste disposal and storage together with risks for reactor accidents from nuclear power plants are now causing public anxiety. This commentary concerns among all high-level radioactive waste management from nuclear fuel cycle facilities, with including radioactive wastes from research institutes or hospitals. Also included is wastes produced from reactor decommissioning. For low-level radioactive wastes, the wastes is reduced in volume, solidified, and removed to the sites of storage depending on their radioactivities. For high-level radioactive wastes, some ten thousand years must be necessary before the radioactivity decays to the natural level and protection against seismic or volcanic activities, and terrorist attacks is unavoidable for final disposals. This inevitably results in underground disposal at least 300 m below the ground. Various proposals for the disposal and management for this and their evaluation techniques are described in the present document. (S. Ohno)

Characterizing, for packaging and transport, large objects contaminated by radioactive material having a limited A2 value

International Nuclear Information System (INIS)

Pope, R.B.; Shappert, L.B.; Michelhaugh, R.D.; Cash, J.M.; Best, R.E.

1998-02-01

The International Atomic Energy Agency (IAEA) Regulations for the safe packaging and transportation of radioactive materials follow a graded approach to the requirements for both packaging and controls during transport. The concept is that, the lower the risk posed to the people and the environment by the contents, (1) the less demanding are the packaging requirements and (2) the smaller in number are the controls imposed on the transport of the material. There are likely to be a great number of situations arising in coming years when large objects, contaminated with radioactive material having unlimited A 2 values will result from various decommissioning and decontamination (D and D) activities and will then require shipment from the D and D site to a disposal site. Such situations may arise relatively frequently during the cleanup of operations involving mining, milling, feedstock, and uranium enrichment processing facilities. Because these objects are contaminated with materials having an unlimited A 2 value they present a low radiological risk to worker and public safety and to the environment during transport. However, when these radioactive materials reside on the surfaces of equipment and other large objects, where the equipment and objects themselves are not radioactive, the radioactive materials appear as surface contamination and, if the contaminated object is categorized as a surface contaminated object, it would need to be packaged for shipment according to the requirements of the Regulations for SCO. Despite this categorization, alternatives may be available which will allow these contaminants, when considered by themselves for packaging and transport, to be categorized as either (1) a limited quantity of radioactive material to be shipped in an excepted package or (2) low specific activity (LSA) materials to be shipped in an IP-1 package or possibly even shipped unpackaged. These options are discussed in this paper

Development of the Holifield Radioactive Ion Beam Facility

International Nuclear Information System (INIS)

Tatum, B.A.

1997-01-01

The Holifield Radioactive Ion Beam Facility (HRIBF) construction project has been completed and the first radioactive ion beam has been successfully accelerated. The project, which began in 1992, has involved numerous facility modifications. The Oak Ridge Isochronous Cyclotron has been converted from an energy booster for heavy ion beams to a light ion accelerator with internal ion source. A target-ion source and mass analysis system have been commissioned as key components of the facility's radioactive ion beam injector to the 25MV tandem electrostatic accelerator. Beam transport lines have been completed, and new diagnostics for very low intensity beams have been developed. Work continues on a unified control system. Development of research quality radioactive beams for the nuclear structure and nuclear astrophysics communities continues. This paper details facility development to date

Radioactive contamination of the Yenisei River

International Nuclear Information System (INIS)

Vakulovsky, S.M.; Kryshev, I.I.; Nikitin, A.I.; Savitsky, Y.V.; Malyshev, S.V.; Tertyshnik, E.G.

1995-01-01

Based on observational data in the period 1971-1993, radioactive contamination of the Yenisei River ecosystem was analysed within 2000 km of the site of discharges from the Krasnoyarsk Mining and Chemical Industrial Complex. Data on the content of 24 Na, 32 P, 46 Sc, 51 Cr, 54 Mn, 56 Mn, 58 Co, 60 Co, 59 Fe, 65 Zn, 90 Sr, 95 Zr, 95 Nb, 103 Ru, 106 Ru, 134 Cs, 137 Cs, 140 Ba, 141 Ce, 144 Ce and 239 Np in the river ecosystem components were generalised. Radioactive contamination of water in the near zone of discharges (within 15 km) was shown to be determine mainly by the short-lived nuclides, such as 24 Na, 32 P, 56 Mn and 239 Np, as well as 51 Cr. Outside the near zone the water contamination level decreased appreciably. According to observational data of 1973, the total contamination inventory of the river bottom in the near zone was as great as 5800 kBq m -2 . More than half was accounted for by two radionuclides: 51 Cr and 65 Zn. At a distance of 1930 km from the site of discharges a technogenic activity of bottom sediments amounted to 5 kBq m -2 and was accounted for by 137 Cs and 65 Zn. The main radionuclide accumulated in fish was 32 P. Exposure doses to aquatic organisms and population were assessed in the near and far zones of the Krasnoyarsk radioactive contamination trace. Within 250 km of the site of discharges the exposure dose to the population from a consumption of 1 kg of fish was shown to amount to an average of 10 μSv. (author)

Radioactive contamination in metal recycling industry - an environmental issue

International Nuclear Information System (INIS)

Agarwal, S.P.

2012-01-01

Metal recycling has become an important industrial activity worldwide; it is seen as being socially and environmentally beneficial because it conserves natural ore resources and saves energy. However, there have been several accidents over the past decades involving orphan radioactive sources or other radioactive material that were inadvertently collected as metal scrap that was destined for recycling. The consequences of these accidents have been serious with regard to the protection of people and the environment from the harmful effects of ionizing radiation as well as from an economic point of view. India produces and exports steel products to various countries. In the recent years there were rejection and return of steel products as they were found to be contaminated with trace quantities of radioactive materials. During investigation of incidents of radioactive contamination in steel products exported from India, it was observed that steel products are contaminated with low level radioactivity. Though radioactivity level in steel products is found to be too low to pose any significant hazards to the handling personnel or to the users or the public at large, its presence is undesirable and need to be probed as to how it has entered in the steel products. Atomic Energy Regulatory Board (AERB) has investigated the incidents of such nature in the recent past and it is gathered that the steel products are made out of steel produced in a foundry where metal scrap containing radioactive material has been used. In this talk, incidents of radioactive contamination, its roots cause, and its radiological impact on person, property and environment, lessons learnt, remedial measures and international concerns will be discussed

The radioactive contamination level in Croatia by means of radioactive rainwaters, caused by the accident in NPP 'Lenin'

International Nuclear Information System (INIS)

Barishicj, D.; Koshuticj, K.; Kvastek, K.; Lulicj, S.; Tuta, J.; Vertachnik, A.; Vrhovac, A.

1987-01-01

In this paper, the radioactive contamination level in Croatia by means of radioactive rainwaters, caused by the accident in NPP 'Lenin', has been described. The results represent the sum of measured and evaluated data, the map of the radioactive contamination in Croatia caused by radioactive rainwaters between April, 28 to May, 20 1986 has been constructed. (author) 3 tabs.; 5 figs

Development of a state radioactive materials storage facility

International Nuclear Information System (INIS)

Schmidt, P.S.

1995-01-01

The paper outlines the site selection and facility development processes of the state of Wisconsin for a radioactive materials facility. The facility was developed for the temporary storage of wastes from abandoned sites. Due to negative public reaction, the military site selected for the facility was removed from consideration. The primary lesson learned during the 3-year campaign was that any project involving radioactive materials is a potential political issue

Method of melt-decontaminating alumium contaminated with radioactivity

International Nuclear Information System (INIS)

Uda, Tatsuhiko; Iba, Hajime; Miura, Noboru; Kawasaki, Katsuo.

1986-01-01

Purpose: To enable optimum deontamination for radioactive-contaminated aluminum by further improving the decontaminating effect of the slag agent added to radioactive contaminated materials. Method: The slag agent is mainly composed of chloride type slags having a high reactivity for mainly incorporating uranium compounds and easily reacting near the melting point of aluminum and incorporated with fluorides for weakening the deliquescent characteristic to the chloride materials. Further, those slag agents are selected which can be treated at a low temperature in order to prevent the uranium compounds once incorporated into the slags from re-melting into the molten aluminum. Typically, a slag agent comprising 14 LiF, 76 KCl - 10 BaCl 2 is preferred. The basicity of the slag agent ranges from 0.5 to 2 and the melting point is 700 deg C. The melting decontaminating efficiency for the radioactive-contaminated aluminum can thus be improved. (Horiuchi, T.)

Quantitative analysis of education effect by the number of contamination in an unsealed radioisotope facility

International Nuclear Information System (INIS)

Matsuda, Naoki; Yoshida, Masahiro; Takao, Hideaki; Kaneko, Mamoru; Yamaguchi, Yukiko; Okumura, Yutaka

2002-01-01

The educational program for radiation workers is essential for the safety of radiation facility that stands on radiation protection practice by each worker. However, there appears no distinct criterion for quantitative evaluation of the education effect on radiation safety. The effectiveness of education was assessed by the number and the frequency (number of contamination/number of users) of contamination, a major incident involving radioactive materials, based on the long-term contamination surveillance data from 1996 to 2001 in Nagasaki University Radioisotope Center. Facility staffs monitored contamination in the facility every day. In 1996 and 1997, the yearly total number and the frequency of contamination found in a molecular biology room, a most frequently-used laboratory, were 150 and 1.21, respectively. The improvement of education program, including introduction of technical procedures to avoid contamination in molecular biological experiments, pre-entry instruction for fresh workers to demonstrate radiation safety practices on site, and spreading the new concept 'contamination happens by all means' through the radiation workers, markedly reduced both the number and the frequency of contamination to 33 and 0.48, respectively. This reduction seemed to be attributable for two different reasons; improvement of skills to avoid contamination, and thorough execution of monitoring and decontamination. These results suggested that contamination was a possible criterion for evaluating effectiveness of education program for radiation workers. (author)

Treatment and conditioning of historical radioactive waste

International Nuclear Information System (INIS)

Dogaru, Ghe.; Dragolici, F.; Ionascu, L.; Rotarescu, Ghe.

2009-01-01

The paper describes the management of historical radioactive waste from the storage facility of Radioactive Waste Treatment Plant. The historical waste stored into storage facility of IFIN-HH consists of spent sealed radioactive sources, empty contaminated containers, wooden radioactive waste, low specific activity radioactive waste, contaminated waste as well as radioactive waste from operation of WWR-S research reactor. After decommissioning of temporary storage facility about 5000 packages with radioactive waste were produced and transferred to the disposal facility. A large amount of packages have been transferred and disposed of to repository but at the end of 2000 there were still about 800 packages containing cement conditioned radioactive waste in an advanced state of degradation declared by authorities as 'historical waste'. During the management of historical waste campaign there were identified: radium spent radioactive sources, containers containing other spent sealed radioactive sources, packages containing low specific activity waste consist of thorium scrap allow, 30 larger packages (316 L), packages with activity lower than activity limit for disposal, packages with activity higher than activity limit for disposal. At the end of 2008, the whole amount of historical waste which met the waste acceptance criteria has been conditioned and transferred to disposal facility. (authors)

Treatment of heterogeneous mixed wastes: Enzyme degradation of cellulosic materials contaminated with hazardous organics and toxic and radioactive metals

International Nuclear Information System (INIS)

Vanderberg, L.A.; Foreman, T.M.; Attrep, M. Jr.; Brainard, J.R.; Sauer, N.

1999-01-01

The redirection and downsizing of the US Department of Energy's nuclear weapons complex requires that many facilities be decontaminated and decommissioned (D and D). At Los Alamos National Laboratory, much of the low-level radioactive, mixed, and hazardous/chemical waste volume handled by waste management operations was produced by D and D and environmental restoration activities. A combination of technologies--air stripping and biodegradation of volatile organics, enzymatic digestion of cellulosics, and metal ion extraction--was effective in treating a radiologically contaminated heterogeneous paint-stripping waste. Treatment of VOCs using a modified bioreactor avoided radioactive contamination of byproduct biomass and inhibition of biodegradation by toxic metal ions in the waste. Cellulase digestion of bulk cellulose minimized the final solid waste volume by 80%. Moreover, the residue passed TCLP for RCRA metals. Hazardous metals and radioactivity in byproduct sugar solutions were removed using polymer filtration, which employs a combination of water-soluble chelating polymers and ultrafiltration to separate and concentrate metal contaminants. Polymer filtration was used to concentrate RCRA metals and radioactivity into <5% of the original wastewater volume. Permeate solutions had no detectable radioactivity and were below RCRA-allowable discharge limits for Pb and Cr

Structure and dimensions of radioactive contamination caused by use of nuclear weapons

International Nuclear Information System (INIS)

Ilijas, B.

1996-01-01

Radioactive contamination is one of unavoidable consequences of nuclear burst. Its structure and dimensions are depended of many factors connected with type of weapon, with meteorological conditions and location of burst and characteristics of area involved. Contamination manifests in two ways - as induced radioactivity in the nearness of the center of explosion and as radioactive fallout. Induced radioactivity originates from interaction of neutrons from primary beam with elements naturally presents in environment, which results in creating radionuclides and area of radioactive contamination. Radioactive fallout consists of material formed or collected in the explosion that falls on earth in form of small particles. This contaminant contains α, β and γ sources with structure dependent of explosive energy and location of burst. Some radionuclides, often present in fallout, are very dangerous as internal sources ( 90 Sr, 131 I, 137 Cs, 239 Pu). Dimension of contaminated area varies widely, but if one has Knowledge of enough parameters, it is possible to predict its shape, as well as dose rate on some distance from zero point. Preciseness of this work is essentially affected by credibility of data involved and by kind of selected model. Using of well-chosen model enables on-time evaluation of risk from radioactive contamination and planning adequate protection. (author)

Low-waste technology of prevention, decontamination and localization of radioactive contamination

International Nuclear Information System (INIS)

Kizhnerov, L. V.; Konstantinov, Ye. A.; Prokopenko, V. A.; Sorokin, N. M.

1997-01-01

The report presents the results of research in developing a low-waste technology of prevention, decontamination and localization of radioactive contamination founded on the of easily removed protective polymeric coating based on water and alcohol latexes and dispersion of polymers with special activating additives. The developed technology provides for the reduction of weakly fixed radioactive contamination of non-painted and painted surfaces to admissible levels (as a rule), it securely prevents and localizes contamination and does not generate secondary liquid radioactive wastes

Control System Radioactive Contamination in Food Samples in Poland

International Nuclear Information System (INIS)

Grabowski, D.; Kurowski, W.; Muszynski, W.; Rubel, B.; Smagala, G.; Swietochowska, J.

2001-01-01

Full text: The analyses of the level of radioactive contamination in food samples are carried out by the Service for Measurements of Radioactive Contamination (SMRC) in Poland. The Service was brought into existence in 1961. The Service comprises of a network of measurement stations and the Centre of Radioactive Contamination Measurements (CRCM). The duty of the Centre is being executed by the Central Laboratory for Radiological Protection (CLRP). The uniform methods of sampling are used in measurement stations. All important foodstuff: milk, meat, vegetables, fruit, cereals are controlled in the Service stations. The radiochemical and spectrometric methods are used to determine the activity of radioactive isotopes. The standard equipment of the measurement station is the measurement system type SAPOS-90 and multichannel analyser with scintillation or germanium detector. The structure of the Service, kinds of samples tested by each station, program of sampling in normal and during accident situation are presented in this paper. (author)

The ISOLDE Facility: Radioactive beams at CERN

CERN Multimedia

CERN. Geneva

2007-01-01

The Isope Separation On-Line (ISOL) technique evolved from chemical techniques used to separate radioactive isotopes off-line from irradiated "targets". The ISOL targets of today, used at e.g. ISOLDE, can be of many different types and in different phases but the isotopes are always delivered at very low energies making the technique ideal for study of ground state properties and collections for other applications such as solid state physics and medical physics. The possibility of accelerating these low energy beams for nuclear structure studies, and in the long term future for neutrino physics, is now being explored at first generation radioactive beam facilities. The upgrade towards HIE-ISOLDE aim to consolidate ISOLDE's position as a world leading radioactive nuclear beam facility and it will be a pre-cursor to a future all European ISOL facility, EURISOL, with order of magnitudes higher radioactive beam intensities and energies. Prerequisite knowledge and references: None

Annual Report of Radioactive Waste Facilities Operation in 2015

Institute of Scientific and Technical Information of China (English)

DU; Hong-ming; GAO; Zhi-gang; DIAO; Lei; SHEN; Zheng; LI; Wen-ge

2015-01-01

301of the Department of Radiochemistry,is in charge of the management of radioactive waste and the safety of the relative facilities to meet the request of the scientific research production.There are 16radioactive waste facilities,including9facilities which are closed and monitored

Radioactivity measurement of radioactive contaminated soil by using a fiber-optic radiation sensor

Science.gov (United States)

Joo, Hanyoung; Kim, Rinah; Moon, Joo Hyun

2016-06-01

A fiber-optic radiation sensor (FORS) was developed to measure the gamma radiation from radioactive contaminated soil. The FORS was fabricated using an inorganic scintillator (Lu,Y)2SiO5:Ce (LYSO:Ce), a mixture of epoxy resin and hardener, aluminum foil, and a plastic optical fiber. Before its real application, the FORS was tested to determine if it performed adequately. The test result showed that the measurements by the FORS adequately followed the theoretically estimated values. Then, the FORS was applied to measure the gamma radiation from radioactive contaminated soil. For comparison, a commercial radiation detector was also applied to measure the same soil samples. The measurement data were analyzed by using a statistical parameter, the critical level to determine if net radioactivity statistically different from background was present in the soil sample. The analysis showed that the soil sample had radioactivity distinguishable from background.

Bonding of radioactive contamination. IV. Effect of surface finish

International Nuclear Information System (INIS)

Rankin, W.N.

1983-01-01

The mechanisms by which radioactive contamination would be bonded to a DWPF canister are being investigated. Previous investigations in this series have examined the effects of temperature, oxidation before contamination, and atmosphere composition control on the bonding of contamination. This memorandum describes the results of tests to determine the effect of special surface finishes on the bonding of contamination to waste glass canisters. Surface pretreatments which produce smoother canister surfaces actually cause radioactive contamination to be more tightly bonded to the metal surface than on an untreated surface. Based on the results of these tests it is recommended that the canister surface finish be specified as having a bright cold rolled mill finish equivalent to ASTM No. 2B. 7 references, 3 figures, 3 tables

Hanford's Radioactive Mixed Waste Disposal Facility

International Nuclear Information System (INIS)

McKenney, D.E.

1995-01-01

The Radioactive Mixed Waste Disposal Facility, is located in the Hanford Site Low-Level Burial Grounds and is designated as Trench 31 in the 218-W-5 Burial Ground. Trench 31 is a Resource Conservation and Recovery Act compliant landfill and will receive wastes generated from both remediation and waste management activities. On December 30, 1994, Westinghouse Hanford Company declared readiness to operate Trench 31, which is the Hanford Site's (and the Department of Energy complex's) first facility for disposal of low-level radioactive mixed wastes

Certification Plan, Radioactive Mixed Waste Hazardous Waste Handling Facility

International Nuclear Information System (INIS)

Albert, R.

1992-01-01

The purpose of this plan is to describe the organization and methodology for the certification of radioactive mixed waste (RMW) handled in the Hazardous Waste Handling Facility at Lawrence Berkeley Laboratory (LBL). RMW is low-level radioactive waste (LLW) or transuranic (TRU) waste that is co-contaminated with dangerous waste as defined in the Westinghouse Hanford Company (WHC) Solid Waste Acceptance Criteria (WAC) and the Washington State Dangerous Waste Regulations, 173-303-040 (18). This waste is to be transferred to the Hanford Site Central Waste Complex and Burial Grounds in Hanford, Washington. This plan incorporates the applicable elements of waste reduction, which include both up-front minimization and end-product treatment to reduce the volume and toxicity of the waste; segregation of the waste as it applies to certification; an executive summary of the Waste Management Quality Assurance Implementing Management Plan (QAIMP) for the HWHF (Section 4); and a list of the current and planned implementing procedures used in waste certification

Environmental radioactive contamination

International Nuclear Information System (INIS)

Saucedo, Edgardo

2000-01-01

The environmental radioactive contamination with the scientific and technological advances can produce big benefits or damages to the human beings or the environment. The approval of national or international laws in the population's education so that it can face the topic critically and the scientific formation of human resources and ethically for application of the ionizing radiations, they are the best road to take advantage to the maximum of benefits of these radiations, reducing to the minimum the risks on the man and the environment

Ecological Role of Soils upon Radioactive Contamination

Science.gov (United States)

Tsvetnov, Evgeny; Shcheglov, Alexei; Tsvenova, Olga

2016-04-01

The ecological role of soils upon radioactive contamination is clearly manifested in the system of notions about ecosystems services, i.e., benefits gained by humans from ecosystems and their components, including soils (Millennium Ecosystem Assessment, 2005). For the soils, these services are considered on the basis of soil functions in the biosphere that belong to the protective ecosystem functions within the group of soil functions known under the names of "Buffer and protective biogeocenotic shield" (at the level of particular biogeocenoses) and "Protective shield of the biosphere" (at the global biospheric level) (according to Dobrovol'skii & Nikitin, 2005). With respect to radionuclides, this group includes (1) the depositing function, i.e., the accumulation and long-term sequestration of radioactive substances by the soil after atmospheric fallout; (2) the geochemical function, i.e., the regulation of horizontal and vertical fluxes of radionuclides in the system of geochemically conjugated landscapes and in the soil-groundwater and soil-plant systems; and (3) the dose-forming function that is manifested by the shielding capacity of the soil with respect to the external ionizing radiation (lowering of the dose from external radiation) and by the regulation of the migration of radionuclides in the trophic chain (lowering of the dose from internal radiation). The depositing and geochemical functions of the soils are interrelated, which is seen from quantitative estimates of the dynamics of the fluxes of radionuclides in the considered systems (soil-plant, soil-groundwater, etc.). The downward migration of radionuclides into the lower soil layers proceeds very slowly: for decades, more than 90% of the pool of radionuclides is stored in the topmost 10 cm of the soil profile. In the first 3-5 years after the fallout, the downward migration of radionuclides with infiltrating water flows decreases from several percent to decimals and hundredths of percent from the

Control of the surface radioactive contamination in the field of biological research; Control de la contaminacion radiactiva superficial en el ambito de la investigacion biologica

Energy Technology Data Exchange (ETDEWEB)

Calvo, S.; Encina, A. de la; Gaspar, J.; Macias, M. T.; Sanchez, A.; Usera, F.

2012-11-01

The manipulation of unsealed sources in biomedical research involves significant risk of radioactive contamination. the aim of this study has been to analyze the radioactive contamination occurring in the field of biomedical research, assessing its magnitude, identifying the equipment that can be contaminated with higher probability and monitoring the evolution of the contaminations production taking into account the radioisotopes and the activities uses, and the radiation protection control applied. The data used for this study correspond to a very lengthy period of time and it have been collected in the radioactive facility, of the Centro Nacional de Biotecnologia (CSIC), a very large biological research centre that can be used perfectly as a reference for this area. The results obtained show a gradual and significant decrease in the incidence of the radioactive contamination. This is due to the optimization of radiation protection standards applied and the implementation or a systematic operational radiation protection program. (Author) 13 refs.

Micro-PIXE evaluation of radioactive cesium transfer in contaminated soil samples

International Nuclear Information System (INIS)

Fujishiro, F.; Ishii, K.; Matsuyama, S.; Arai, H.; Ishizaki, A.; Osada, N.; Sugai, H.; Kusano, K.; Nozawa, Y.; Yamauchi, S.; Karahashi, M.; Oshikawa, S.; Kikuchi, K.; Koshio, S.; Watanabe, K.; Suzuki, Y.

2014-01-01

Highlights: • There are radioactively contaminated soils having a radioactive cesium transfer of 0.01. • Micro-PIXE analysis has revealed an existence of phosphorus in a contaminated soil. • Radioactive cesium captured by phosphorus compound would be due to radioactive transfer. -- Abstract: Micro-PIXE analysis has been performed on two soil samples with high cesium activity concentrations. These soil samples were contaminated by fallout from the accident at Fukushima Daiichi Nuclear Power Plant. One exhibits a radioactive cesium transfer of ∼0.01, and the other shows a radioactive cesium transfer of less than 0.001, even though both samples have high cesium activity concentrations exceeding 10,000 Bq/kg. X-ray spectra and elemental images of the soil samples revealed the presence of chlorine, which can react with cesium to produce an inorganic soluble compound, and phosphorus-containing cesium-capturable organic compounds

Fifth international conference on radioactive waste management and environmental remediation -- ICEM '95: Proceedings. Volume 2: Management of low-level waste and remediation of contaminated sites and facilities

International Nuclear Information System (INIS)

Slate, S.; Baker, R.; Benda, G.

1995-01-01

The objective of this conference is the broad international exchange of information on technologies, operations, management approaches, economics, and public policies in the critical areas of radioactive waste management and environmental remediation. The ICEM '95 technical program includes four parallel program tracks: Low/intermediate-level waste management; High-level waste, spent fuel, nuclear material management; Environmental remediation and facility D and D; and Major institutional issues in environmental management. Volume 2 contains approximately 200 papers divided into the following topical sections: Characterization of low and intermediate level waste; Treatment of low and intermediate level waste; LLW disposal and near-surface contaminant migration; Characterization and remediation of contaminated sites; and Decontamination and decommissioning technologies and experience. Papers have been processed separately for inclusion on the data base

Field test of radioactive high efficiency filter and filter exchange techniques of fuel cycle examination facility

International Nuclear Information System (INIS)

Hwang, Yong Hwa; Lee, Hyung Kwon; Chun, Young Bum; Park, Dae Gyu; Ahn, Sang Bok; Chu, Yong Sun; Kim, Eun Ka.

1997-12-01

The development of high efficiency filter was started to protect human beings from the contamination of radioactive particles, toxic gases and bacillus, and its gradual performance increment led to the fabrication of Ultra Low Penetration Air Filter (ULPA) today. The application field of ULPA has been spread not only to the air conditioning of nuclear power facilities, semiconductor industries, life science, optics, medical care and general facilities but also to the core of ultra-precision facilities. Periodic performance test on the filters is essential to extend its life-time through effective maintenance. Especially, the bank test on HEPA filter of nuclear facilities handling radioactive materials is required for environmental safety. Nowadays, the bank test technology has been reached to the utilization of a minimized portable detecting instruments and the evaluation techniques can provide high confidence in the area of particle distribution and leakage test efficiency. (author). 16 refs., 13 tabs., 14 figs

Technology developments for the identification, mapping, characterisation and segregation of radioactive contamination

International Nuclear Information System (INIS)

Smith, R.; Beddow, H.; Adsley, T.; Pearman, I.; Sweeney, A.; Smith, W.; Blythe, M.; Davies, M.

2015-01-01

The history of activities in the UK dealing with radioactive materials has led to many sites being contaminated by various radioactive isotopes. These come from a number of industries and educational activities such as nuclear power development, luminising works, research facilities and the oil and gas industry. These isotopes include radium, lead, polonium, thorium, uranium and trans-uranic elements. To remediate these sites it is essential that the isotopes are identified and quantified to enable the appropriate strategy to be developed and the most cost-efficient decontamination or sorting processes to be implemented. Nuvia has developed and implemented a suite of technologies to map the location of and to recover and process radioactive materials during remedial operations. These have been developed over a number of years to meet the requirements for both an effective remediation operation and to comply with the relevant regulatory requirements. This paper will describe these developments and give examples of their deployment in a diverse range of situations.(authors)

Radioactive contamination of sewage sludge

International Nuclear Information System (INIS)

Soeder, C.J.; Zanders, E.; Raphael, T.

1986-01-01

Because of the radioactivity released through the explosion of the nuclear reactor near Chernobyl radionuclides have been accumulated to a significant extent in sewage sludge in the Federal Republic of Germany. This is demonstrated for samples from four activated sludge plants according to a recent recommendation of the German Commission for Radiation Protection, there is until now no reason to deviate from the common practices of sludge disposal or incineration. The degree of radioactive contamination of plant materials produced on farm lands on which sewage sludge is being spread cannot be estimated with sufficient certainty yet. Additional information is required. (orig.) [de

Radioactive contamination of workers. General recommendation and procedures

International Nuclear Information System (INIS)

Mastro, N.L. del; Santos, O.R. dos; Silva, E.N.D.; Santos, A.J. dos.

1987-09-01

The present publication has an objective to provide data and information to be used by workers who handle with or eventually could enter in touch with radioactives substances. The authors have made a compilation of subjects got from the literature on several aspects about radiocontamination, physical and chemical characteristics of radioisotopes, main sources of radioactive contamination, biological basis and treatement of internal and external decontamination. Special attention was paid to iodine and actinides contamination, particularly to uranium and plutonium. The conclusion are presented as general recommendation and synoptic tables. (Author) [pt

Early-stage bioassay for monitoring radioactive contamination in living livestock.

Science.gov (United States)

Yamaguchi, Toshiro; Sawano, Kaita; Kishimoto, Miori; Furuhama, Kazuhisa; Yamada, Kazutaka

2012-12-01

Soil samples from the ground surface and feces and blood from a mixed-breed male pig were collected on April 10, 2011 at a farm within 20 km of the Fukushima Daiichi nuclear power plant. The radioactivity of each sample was measured using a Ge semiconductor detector. Despite the fact that the pig had been fed non-contaminated imported feed, (131)I, (134)Cs and (137)Cs were detected in the feces, and (134)Cs and (137)Cs were detected in the blood clots. Because it is considerably difficult to measure radioactive contamination in the edible muscle of living livestock, bioassays are an option for the screening of radioactive contamination in living livestock to ensure food safety.

Radioactive contamination in monitors received for calibration; Contaminacao em monitores de radiacao recebidos para calibracao

Energy Technology Data Exchange (ETDEWEB)

Dias, Paulo S.; Santos, Gilvan C. dos; Brunelo, Maria Antonieta G.; Paula, Tiago C. de; Pires, Marina A.; Borges, Jose C. [MRA Comercio de Instrumentos Eletronicos Ltda., Jardinopolis, SP (Brazil). Centro de Ensaios e Pesquisas em Metrologia (METROBRAS)

2013-10-01

The Calibration Laboratory - LABCAL, from the Research Center for Metrology and Testing - METROBRAS, MRA Comercio de Instrumentos Eletronicos Ltda., began activities in October 2008 and, in August 2009, decided to establish a procedure for monitoring tests, external and internal, of all packages received from customers, containing instruments for calibration. The aim was to investigate possible contamination radioactive on these instruments. On July 2011, this procedure was extended to packagings of personal thermoluminescent dosemeters - TLD, received by the newly created Laboratory Laboratorio de Dosimetria Pessoal - LDP . In the monitoring procedure were used monitors with external probe, type pancake, MRA brand, models GP - 500 and MIR 7028. During the 37 months in which this investigation was conducted, were detected 42 cases of radioactive contamination, with the following characteristics: 1) just one case was personal dosimeter, TLD type; 2) just one case was not from a packing from nuclear medicine service - was from a mining company; 3) contamination occurred on packs and instruments, located and/or widespread; 4) contamination values ranged from slightly above the level of background radiation to about a thousand fold. Although METROBRAS has facilities for decontamination, in most cases, especially those of higher contamination, the procedure followed was to store the contaminated material in a room used for storage of radioactive sources. Periodically, each package and/or instrument was monitored, being released when the radiation level matched the background radiation. Every contamination detected, the client and/or owner of the instrument was informed. The Brazilian National Energy Commission - CNEN, was informed, during your public consultation for reviewing the standard for nuclear medicine services, held in mid-2012, having received from METROBRAS the statistical data available at the time. The high frequency of contamination detected and the high

Environmental review of options for managing radioactively contaminated carbon steel

International Nuclear Information System (INIS)

1996-10-01

The U.S. Department of Energy (DOE) is proposing to develop a strategy for the management of radioactively contaminated carbon steel (RCCS). Currently, most of this material either is placed in special containers and disposed of by shallow land burial in facilities designed for low-level radioactive waste (LLW) or is stored indefinitely pending sufficient funding to support alternative disposition. The growing amount of RCCS with which DOE will have to deal in the foreseeable future, coupled with the continued need to protect the human and natural environment, has led the Department to evaluate other approaches for managing this material. This environmental review (ER) describes the options that could be used for RCCS management and examines the potential environmental consequences of implementing each. Because much of the analysis underlying this document is available from previous studies, wherever possible the ER relies on incorporating the conclusions of those studies as summaries or by reference

Radioactive contamination of copper produced using nuclear explosives

Energy Technology Data Exchange (ETDEWEB)

Crouse, D J; Arnold, W D; Hurst, F J

1970-05-15

Laboratory tests simulating the processing of copper ore after fracturing with nuclear explosives indicate that only very small fractions of the radioactive fission products will be dissolved on leaching with dilute sulfuric acid. Tritium (as tritiated water) will be by far the dominant radionuclide in the circulating leach liquor, assuming use of a fusion device. Only 106Ru appears of significant importance with respect to contamination of the cement copper. It is rejected effectively in electrolytic purification and, therefore, the final copper product should be very low in radiocontamination and not hazardous to the customer. The activity level may be high enough, however, to make the copper unsuitable for some specific uses. If necessary, solvent extraction can be used as an alternative to the cementation process to reduce the radioactivity of the copper products. The tritium in the circulating liquor and the 106Ru in the cement copper are potential hazards at the plant site and must be given consideration in designing and operating the facility. However since the activity levels will be low, the protection necessary to ensure safety of the operating personnel should be neither difficult nor costly to provide. (author)

Radioactive contamination of food and the intake by man

International Nuclear Information System (INIS)

Frissel, M.J.; Blaauboer, R.O.; Koester, H.W.; Leenhouts, H.P.; Stoutjesdijk, J.F.; Vaas, L.H.

1989-01-01

This paper describes the different pathways by which food is contaminated after a release of radionuclides into the environment. Equations to calculate the contamination level, as well as the most important parameters used in these equations, are included. Thereupon is explained how the radiation dose can be calculated from the intake of radioactivity. The principles which are used to derive criteria for the amounts of radioactivity which are allowed in food are described. (author)

Defense Waste Processing Facility radioactive operations -- Part 2, Glass making

International Nuclear Information System (INIS)

Carter, J.T.; Rueter, K.J.; Ray, J.W.; Hodoh, O.

1996-01-01

The Savannah River Site's Defense Waste Processing Facility (DWPF) near Aiken, SC is the nation's first and world's largest vitrification facility. Following a ten year construction period and nearly 3 year non-radioactive test program, the DWPF began radioactive operations in March, 1996. The results of the first 8 months of radioactive operations are presented. Topics include facility production from waste preparation batching to canister filling

Current state of the technology measures of accident from contamination by the radioactive substance. 2. Overall management of radioactive material contaminated waste in the off-site

International Nuclear Information System (INIS)

Endo, Kazuto

2015-01-01

This paper focuses on the disposal standards of the Act on Special Measures Concerning the Handling of Environmental Pollution by Radioactive Materials by the NPS Accident Associated with the Tohoku District - off the Pacific Ocean Earthquake that Occurred on March 11, 2011, which was promulgated on August 30, 2011 as a framework for the management of radioactively contaminated waste and removed soil. It stipulated that the byproducts of water/sewage treatment, major ash, and fly ash up to the radiation of 8,000 Bq/kg can be reclaimed in land. However, fly ash has a limit in landfill conditions, due to very high leaching rate of radioactive cesium. Later, incineration ash with between 8,000 Bq/kg and 100,000 Bq/kg became possible to be buried at disposal sites corresponding to leachate-controlled type. The specified waste with 100,000 Bq/kg or above is reclaimed in land with specified method at a site provided with outer peripheral partition facilities and cut off from the public water and groundwater. In Fukushima Prefecture, the specified waste with 100,000 Bq/kg or above is to be stored in provisional storage facilities, and later sent to final disposal sites outside the prefecture after the volume has been reduced. The decontaminated waste composed of vegetation is covered totally with a breathable waterproof sheet, and stored at a provisional yard. According to the characteristics of each provisional storage yard, there are needs for patrol and management. (A.O.)

An overview of sites contaminated by radioactivity

International Nuclear Information System (INIS)

Eisenbud, M.

1991-01-01

This paper discusses contamination of land and water by radioactive material which is a subject that has been receiving widespread media attention, and has become the cause of much public anxiety. The contaminated sites can be divided broadly into three groups: Those that are quite old, relatively small in size, and the legacy of non-nuclear industrial activities involved with natural radioactivity, mostly in the early part of the century; the chain of uranium extraction plants used during and shortly after World War II, and the plants and laboratories that comprise the Department of Energy (DOE) research and weapons production complex today. It is the latter group that is the focus of greatest public attention at the present time

Distinguishing method for contamination/radio-activation of radioactive wastes

International Nuclear Information System (INIS)

Fukazawa, Takuji; Kato, Keiichiro; Koda, Satoshi.

1994-01-01

The present invention concerns a method of distinguishing the contamination/radio-activation of radioactive wastes used in processing wastes generated upon dismantling of exhausted nuclear reactors. Especially, contaminated/radio-activation is distinguished for wastes having openings such as pipes and valves, by utilizing scattering of γ-rays or γ-ray to β-ray ratio. That is, ratio of scattered γ-rays and direct γ-rays or ratio of β-rays and γ-rays from radioactive wastes are measured and compared by a radiation detector, to distinguish whether the radioactive wastes contaminated materials or radio-activated materials. For example, when an object to be measured having an opening is contaminated at the inner side, the radiation detector facing to the opening mainly detects high direct γ-rays emitted from the object to be measured while a radiation detector not facing the opening mainly detects high scattered γ-rays relatively. On the other hand, when the object is a radio-activated material, any of the detectors detect scattered γ-rays, so that they can be distinguished by these ratios. (I.S.)

Development of RadRob15, A Robot for Detecting Radioactive Contamination in Nuclear Medicine Departments

Directory of Open Access Journals (Sweden)

Shafe A.

2016-09-01

Full Text Available Accidental or intentional release of radioactive materials into the living or working environment may cause radioactive contamination. In nuclear medicine departments, radioactive contamination is usually due to radionuclides which emit high energy gamma photons and particles. These radionuclides have a broad range of energies and penetration capabilities. Rapid detection of radioactive contamination is very important for efficient removing of the contamination without spreading the radionuclides. A quick scan of the contaminated area helps health physicists locate the contaminated area and assess the level of activity. Studies performed in IR Iran shows that in some nuclear medicine departments, areas with relatively high levels of activity can be found. The highest contamination level was detected in corridors which are usually used by patients. To monitor radioactive contamination in nuclear medicine departments, RadRob15, a contamination detecting robot was developed in the Ionizing and Non-ionizing Radiation Protection Research Center (INIRPRC. The motor vehicle scanner and the gas radiation detector are the main components of this robot. The detection limit of this robot has enabled it to detect low levels of radioactive contamination. Our preliminary tests show that RadRob15 can be easily used in nuclear medicine departments as a device for quick surveys which identifies the presence or absence of radioactive contamination.

Some problems of risk assessment in cases of environmental radioactive and chemical contamination in regions of the Ural radioactive trail

International Nuclear Information System (INIS)

Kryshev, I.I.; Isaeva, L.N.; Sazykina, T.G.

1995-01-01

A methodology of risk assessment if being developed to permit the analysis of possible consequences of radioactive and chemical environment contamination on the territory of the Urals radioactive trail. The assessment of hazards from radioactive contamination of the Techa river (Muslyumovo) has been carried out. A comparison of radioactive and chemical risks for the population of Kasli has been made

Bonding of radioactive contamination. III. Auger electron spectroscopic investigation

International Nuclear Information System (INIS)

Rankin, W.N.; Whitkop, P.G.

1983-01-01

The mechanisms by which radioactive contamination would be bonded to a DWPF canister surface are being investigated. Tests with low pressure water and air-injected water decontamination of radioactive specimens showed that bonding of contamination increases rapidly with postoxidation temperature. Even with the least severe temperature conditions expected on the waste glass canister, bonding is so great that decontamination cannot be affected by water-only techniques. A preoxidation film increased rather than decreased bonding. This memorandum describes detailed surface analyses of coupons simulating DWPF canister surfaces. Based on this examination we conclude: contamination will be dispersed throughout the oxide film on DWPF canisters. Contamination is concentrated at the surface, decreasing farther into the oxide film; some samples contain sludge contamination at the steel/oxide interface. This was not the case for semi-volatile (Cs 2 O) contamination; in samples with contamination at the steel/oxide interface, at least 80% of the contamination is usually in the oxide layer; no difference in contamination dispersion between preoxidized and non-preoxidized samples was found; and postoxidation atmosphere had no effect on the contamination dispersion within the oxide layer. 6 references, 9 figures

Standard Guide for Post-Deactivation Surveillance and Maintenance of Radiologically Contaminated Facilities

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This guide outlines a method for developing a Surveillance and Maintenance (S&M) plan for inactive nuclear facilities. It describes the steps and activities necessary to prevent loss or release of radioactive or hazardous materials, and to minimize physical risks between the deactivation phase and the start of facility decontamination and decommissioning (D&D). 1.2 The primary concerns for S&M are related to (1) animal intrusion, (2) structural integrity degradation, (3) water in-leakage, (4) contamination migration, (5) unauthorized personnel entry, and (6) theft/intrusion. This document is intended to serve as a guide only, and is not intended to modify existing regulations.

Assessment of risks and costs associated with transportation of US Department of Energy radioactively contaminated carbon steel

International Nuclear Information System (INIS)

Chen, S.-Y.; Arnish, J.J.; Nieves, L.A.; Folga, S.M.

1996-09-01

This report provides a preliminary assessment of potential human health risks and develops unit risks and costs for transporting radioactively contaminated carbon steel (RCCS) scrap between U.S. Department of Energy (DOE) sites. The RCCS would be generated from DOE activities (current or future) and from decontamination and decommissioning of DOE facilities. The estimates of transportation system risk reflect preliminary information regarding the quantities of RCCS at some sites and the spectrum of activity in RCCS at various types of DOE facilities

Contamination and decontamination of vehicles driven in radioactive areas

International Nuclear Information System (INIS)

Ulvsand, T.; Nygren, U.

1999-03-01

There is reason to ask whether it is beneficial to decontaminate vehicles, in view of the great effort applied. If the level of contamination is low before the decontamination process, then the cost is not motivated, even if the decontamination is shown to be effective in relative terms. The report describes two trials at the National NBC Defence School in Umeaa and one trial at the French test site in Bourges. The aim is to investigate how vehicles are contaminated and at which ground deposition levels troublesome levels of contamination will arise. In the trials, a non-radioactive agent substituting real radioactivity was used. The trials in Sweden so far have used the oversnow vehicle BV 206, during both winter and summer conditions. The vehicles were driven a specific distance along a road on which a known amount of the test substance had been dispersed. Samples were taken on pre-determined areas on one side of the vehicles to measure the amount of test substance. Later, the vehicles continued along a 'clean' road where additional samples were taken, but on the other side of the vehicles. The largest amount of test substance was collected on the tracks and on the back of the vehicle. The tracks and mud-flaps were effectively decontaminated when the vehicles were driven along a clean road, while most of the contamination remained on the backside. The purpose of the trials in France was to compare the results from our non-radioactive and their radioactive method, based on the radioactive La-140. Due to ground conditions, the level of contamination on the vehicles was much less than in the trials in Umeaa, but the effect decontamination could be measured after all

Assessment of radioactive contaminations of the ground in Hanover-List with scales and methods of the German Federal Ordinance on Soil Protection and Contaminated Sites (BBodSchV). Pt. 1. Derivation of test thresholds

International Nuclear Information System (INIS)

Gellermann, Rainer; Guenther, Petra; Evers, Burkhard

2010-01-01

Background, aim, and scope: In the district List of Hanover (Lower Saxony) radioactive contaminations of the ground were detected at a site of a former chemical plant. Due to the lack of an ordinance regarding intervention regulations in the case of radioactive contaminations in Germany this situation had to be assessed on the basis of scales and methods of the German regulations concerning soil protection and contaminated sites. In particular it was necessary to develop methods and levels for the assessment of radioactive contaminations. Materials and methods: Because radioactivity can be considered as a carcinogenic substance the methodical approaches of the BBodSchV for this group of substances were used in order to derive test thresholds for radioactive contaminations at children's play areas, residential areas as well as parks and recreation facilities. Results: For the assessment of radioactive soil contaminations with naturally occurring radionuclides at children's play areas and residential areas the ingestion of soil is the decisive pathway of exposure. For children's play areas a threshold level of 0.2 Bq/g for the sum U-238,max + Th-232,max was obtained. At areas with only impacts of ambient radiation from the contaminated ground test thresholds of 0.5 μSv/h are recommended. A special pathway is the migration of radon from the contaminated soil into basement floors of buildings. Taking into account the natural background levels of radon a concentration of 260 Bq/m 3 is suggested as a test threshold in the framework of soil protection benchmarks. Discussion and conclusions will be described in Part 2 of the paper.

Radioactive waste disposal implications of extending Part IIA of the Environmental Protection Act to cover radioactively contaminated land.

Science.gov (United States)

Nancarrow, D J; White, M M

2004-03-01

A short study has been carried out of the potential radioactive waste disposal issues associated with the proposed extension of Part IIA of the Environmental Protection Act 1990 to include radioactively contaminated land, where there is no other suitable existing legislation. It was found that there is likely to be an availability problem with respect to disposal at landfills of the radioactive wastes arising from remediation. This is expected to be principally wastes of high volume and low activity (categorised as low level waste (LLW) and very low level waste (VLLW)). The availability problem results from a lack of applications by landfill operators for authorisation to accept LLW wastes for disposal. This is apparently due to perceived adverse publicity associated with the consultation process for authorisation coupled with uncertainty over future liabilities. Disposal of waste as VLLW is limited both by questions over volumes that may be acceptable and, more fundamentally, by the likely alpha activity of wastes (originating from radium and thorium operations). Authorised on-site disposal has had little attention in policy and guidance in recent years, but may have a part to play, especially if considered commercially attractive. Disposal at BNFL's near surface disposal facility for LLW at Drigg is limited to wastes for which there are no practical alternative disposal options (and preference has been given to operational type wastes). Therefore, wastes from the radioactively contaminated land (RCL) regime are not obviously attractive for disposal to Drigg. Illustrative calculations have been performed based on possible volumes and activities of RCL arisings (and assuming Drigg's future volumetric disposal capacity is 950,000 m3). These suggest that wastes arising from implementing the RCL regime, if all disposed to Drigg, would not represent a significant fraction of the volumetric capacity of Drigg, but could have a significant impact on the radiological

Radioactive waste disposal implications of extending Part IIA of the Environmental Protection Act to cover radioactively contaminated land

International Nuclear Information System (INIS)

Nancarrow, D J; White, M M

2004-01-01

A short study has been carried out of the potential radioactive waste disposal issues associated with the proposed extension of Part IIA of the Environmental Protection Act 1990 to include radioactively contaminated land, where there is no other suitable existing legislation. It was found that there is likely to be an availability problem with respect to disposal at landfills of the radioactive wastes arising from remediation. This is expected to be principally wastes of high volume and low activity (categorised as low level waste (LLW) and very low level waste (VLLW)). The availability problem results from a lack of applications by landfill operators for authorisation to accept LLW wastes for disposal. This is apparently due to perceived adverse publicity associated with the consultation process for authorisation coupled with uncertainty over future liabilities. Disposal of waste as VLLW is limited both by questions over volumes that may be acceptable and, more fundamentally, by the likely alpha activity of wastes (originating from radium and thorium operations). Authorised on-site disposal has had little attention in policy and guidance in recent years, but may have a part to play, especially if considered commercially attractive. Disposal at BNFL's near surface disposal facility for LLW at Drigg is limited to wastes for which there are no practical alternative disposal options (and preference has been given to operational type wastes). Therefore, wastes from the radioactively contaminated land (RCL) regime are not obviously attractive for disposal to Drigg. Illustrative calculations have been performed based on possible volumes and activities of RCL arisings (and assuming Drigg's future volumetric disposal capacity is 950 000 m 3 ). These suggest that wastes arising from implementing the RCL regime, if all disposed to Drigg, would not represent a significant fraction of the volumetric capacity of Drigg, but could have a significant impact on the radiological

Radioactive contamination of oil produced from nuclear-broken shale

International Nuclear Information System (INIS)

Arnold, W.D.; Crouse, D.J.

1970-01-01

The results of small-scale exposure and retorting tests indicate that oil recovered from shale that has been broken with nuclear explosives will be contaminated with tritium. When oil shale was heated in sealed flasks with tritiated water vapor or with tritiated hydrogen, both the shale and the oil subsequently retorted from the shale contained tritium. There was much less contamination of the shale or oil, however, when the shale was exposed to tritiated methane and ethane. Contamination of shale and oil with tritium, as the result, of exposure to tritiated water, increased as the exposure temperature, exposure pressure, and the tritium concentration in the water were increased. This contamination also increased as the exposure time was increased up to 25 days, but not significantly thereafter. More than 90% of the tritium was removed from contaminated shale by treating the shale with moist air at elevated temperatures. Only small amounts of the tritium were removed from crude oil by contacting it with solid drying agents or with water. When tritium-contaminated shale oil was distilled, the tritium contents of the recovered fractions were found to be approximately equal. After being heated with a sample of underground test-shot debris, liquid shale oil became contaminated with radioactive fission products. Most of the radioactivity of the oil was due to finely dispersed solids rather than to dissolved radionuclides. Filtration of the oil removed a major fraction of the radioactive material. When the contaminated oil was distilled, more than 99% of the radionuclides remained in the pot residue. (author)

Radioactive contamination of oil produced from nuclear-broken shale

Energy Technology Data Exchange (ETDEWEB)

Arnold, W D; Crouse, D J

1970-05-15

The results of small-scale exposure and retorting tests indicate that oil recovered from shale that has been broken with nuclear explosives will be contaminated with tritium. When oil shale was heated in sealed flasks with tritiated water vapor or with tritiated hydrogen, both the shale and the oil subsequently retorted from the shale contained tritium. There was much less contamination of the shale or oil, however, when the shale was exposed to tritiated methane and ethane. Contamination of shale and oil with tritium, as the result, of exposure to tritiated water, increased as the exposure temperature, exposure pressure, and the tritium concentration in the water were increased. This contamination also increased as the exposure time was increased up to 25 days, but not significantly thereafter. More than 90% of the tritium was removed from contaminated shale by treating the shale with moist air at elevated temperatures. Only small amounts of the tritium were removed from crude oil by contacting it with solid drying agents or with water. When tritium-contaminated shale oil was distilled, the tritium contents of the recovered fractions were found to be approximately equal. After being heated with a sample of underground test-shot debris, liquid shale oil became contaminated with radioactive fission products. Most of the radioactivity of the oil was due to finely dispersed solids rather than to dissolved radionuclides. Filtration of the oil removed a major fraction of the radioactive material. When the contaminated oil was distilled, more than 99% of the radionuclides remained in the pot residue. (author)

Influence of radioactive contaminants on absorbed dose estimates for radiopharmaceuticals

International Nuclear Information System (INIS)

Watson, E.E.; Stabin, M.G.

1986-01-01

Several popular radiopharmaceutical products contain low levels of radioactive contaminants. These contaminants increase the radiation absorbed dose to the patient without any increased benefit and, in some cases, with a decrease in image quality. The importance of a contaminant to the radiation dosimetry picture is a function of 1) the contaminant level, 2) the physical half-life of the contaminant, 3) the organ uptake and the biological half-time of the contaminant in the various body systems, and 4) the decay mode, energy, etc. of the contaminant. The general influence of these parameters is discussed in this paper; families of curves are included that reflect the changing importance of contaminant dosimetry with respect to the primary radionuclide as a function of these variables. Several specific examples are also given of currently used radiopharmaceutical products which can contain radioactive contaminants (I-123, In-111, Tl-201, Ir-191m, Rb-82, Au-195m). 7 references, 8 figures, 4 tables

Method of electrolytic decontamination of contaminated metal materials for radioactivity

International Nuclear Information System (INIS)

Harada, Yoshio; Ishibashi, Masaru; Matsumoto, Hiroyo.

1985-01-01

Purpose: To electrolytically eliminate radioactive materials from metal materials contaminated with radioactive materials, as well as efficiently remove metal ions leached out in an electrolyte. Method: In the case of anodic dissolution of metal materials contaminated with radioactivity in an electrolyte to eliminate radioactive contaminating materials on the surface of the metal materials, a portion of an electrolytic cell is defined with partition membranes capable of permeating metal ions therethrough. A cathode connected to a different power source is disposed to the inside of the partition membranes and fine particle of metals are suspended and floated in the electrolyte. By supplying an electric current between an insoluble anode disposed outside of the partition membranes and the cathode, metal ions permeating from the outside of the partition membranes are deposited on the fine metal particles. Accordingly, since metal ions in the electrolyte are removed, the electrolyte can always be kept clean. (Yoshihara, H.)

Contamination due to radioactive materials

International Nuclear Information System (INIS)

Woodhead, D.S.

1984-01-01

The peaceful exploitation of radioactivity and the expansion of the nuclear power programme ensure that the disposal of radioactive wastes will cause contamination of the marine environment in the foreseeable future. The exposure of marine organisms to radioactivity from wastes has been studied in depth and related to exposure to natural background radiation. Concentrations of natural radionuclides and those from marine waste disposal have been measured at various stations in the oceans and seas around the world. The fate of radionuclides at four representative sites has been studied and the concentrations of radionuclides in oysters, porphyra, plaice in the Windscale discharge area have been measured. The extent of human exposure, particularly with reference to seafood consumption in local fishing communities, has been assessed. Effects of radiation on developing fish embryos and eggs and genetic radiation effects in aquatic organisms has been studied. The above studies reveal that the controls applied to the discharge of radioactive wastes to limit hazards to humans also provide adequate protection for populations of marine organisms. (U.K.)

Waste processing system for product contaminated with radioactivity

International Nuclear Information System (INIS)

Sotoyama, Koichi; Takaya, Jun-ichi; Takahashi, Suehiro.

1987-01-01

Purpose: To enable to processing contaminated products while separating them into metals at high contamination level and non-metals at low contamination level. Constitution: Pulverized radioactive wastes conveyed on a conveyor belt are uniformly irradiated by a ring-illumination device and then they are picked-up by a television camera or the like. The picked-up signals are sent to an image processing device, applied with appropriate binarization and metal objects are separated by utilizing the light absorbing property of non-metal and light reflection property of metals. The graviational center for the metal object is calculated from the binarized image, the positional information is provided to a robot controller and the metal object is transferred to another position by a robot. Since only the metal object at high radioactive contamination level can be taken out separately, it is no more necessary to process the entire wastes as the high level decontamination products, to thereby provide an economical advantage. (Sekiya, K.)

Substantiation of the permissible radioactive contamination of working clothes

International Nuclear Information System (INIS)

Shcherbakov, V.L.; Korostin, A.S.

1977-01-01

A permissible level of working clothes contamination was determined on the base of the main migration routes of radioactive contaminants: permeation directly through the clothes into subclothes space on skin surface, emission into the air with amount of contaminants subsequently got by the organism of a working person through inhalation as well as transfer in the process of contacting of contaminated working clothes and surfaces of premises equipment, working person hands with amount of contaminants posteriorly got by the organism by alimentary or inhalation ways. Using the experimental and literature data available the permissible levels of working clothes contamination for the mentioned migration routes of radioactive materials have been calculated. According to the data obtained the permissible levels of working clothes contamination must not exceed 4 alpha-part/(cm 2 xmin) for contamination with high-tonic isotopes, 20 alpha-part./(cm 2 xmin) with other alpha-detine isotopes, 1000 beta-part./(cm 2 xmin) with beta-active ones. The permissible level of contamination of additional materials of the individual protection in the case of their contamination with high-tonic alpha-actine isotopes must not exceed 50 alpha-part./(cm 2 xmin), 200 alpha-part./(cm 2 xmin) for contamination th other alpha-active isotopes and 400 beta-part./(cm 2 xmin) with beta-active isotopes

Transuranic-contaminated solid waste Treatment Development Facility. Final safety analysis report

International Nuclear Information System (INIS)

Warner, C.L.

1979-07-01

The Final Safety Analysis Report (FSAR) for the Transuranic-Contaminated Solid-Waste Treatment Facility has been prepared in compliance with the Department of Energy (DOE) Manual Chapter 0531, Safety of Nonreactor Nuclear Facilities. The Treatment Development Facility (TDF) at the Los Alamos Scientific Laboratory is a research and development facility dedicated to the study of radioactive-waste-management processes. This analysis addresses site assessment, facility design and construction, and the design and operating characteristics of the first study process, controlled air incineration and aqueous scrub off-gas treatment with respect to both normal and accident conditions. The credible accidents having potentially serious consequences relative to the operation of the facility and the first process have been analyzed and the consequences of each postulated credible accident are presented. Descriptions of the control systems, engineered safeguards, and administrative and operational features designed to prevent or mitigate the consequences of such accidents are presented. The essential features of the operating and emergency procedures, environmental protection and monitoring programs, as well as the health and safety, quality assurance, and employee training programs are described

Transuranic-contaminated solid waste Treatment Development Facility. Final safety analysis report

Energy Technology Data Exchange (ETDEWEB)

Warner, C.L. (comp.)

1979-07-01

The Final Safety Analysis Report (FSAR) for the Transuranic-Contaminated Solid-Waste Treatment Facility has been prepared in compliance with the Department of Energy (DOE) Manual Chapter 0531, Safety of Nonreactor Nuclear Facilities. The Treatment Development Facility (TDF) at the Los Alamos Scientific Laboratory is a research and development facility dedicated to the study of radioactive-waste-management processes. This analysis addresses site assessment, facility design and construction, and the design and operating characteristics of the first study process, controlled air incineration and aqueous scrub off-gas treatment with respect to both normal and accident conditions. The credible accidents having potentially serious consequences relative to the operation of the facility and the first process have been analyzed and the consequences of each postulated credible accident are presented. Descriptions of the control systems, engineered safeguards, and administrative and operational features designed to prevent or mitigate the consequences of such accidents are presented. The essential features of the operating and emergency procedures, environmental protection and monitoring programs, as well as the health and safety, quality assurance, and employee training programs are described.

Some bioindicators of radioactive contamination

International Nuclear Information System (INIS)

Cosma, C.; Cozmuta, I.; Micu, C.

1996-01-01

The lessons that could be learned from the Chernobyl accident were numerous and encompassed all areas. One of those lead to the discovery of new monitoring methods which also supply to cost-effective solutions to control contaminant radioactive discharges in the environment. Through the measurements performed, we discovered that some samples, because of their radioactive content restrained also for long periods of time, can be used as bioindicators. Hen eggs between May 1-30 1986 were analysed (identification of radionuclides with a Ge(Li) detector and measuring of total gamma activity with NaI(T1)). Various aspects pursued revealed that eggs are precious witness of vegetable food contamination with fission products, especially Ba-140 and I-131, behaving as radionuclide separators (Ba-140 in egg shell -301 Bq/egg and I-131 in the content - 182 Bq/egg). Some of the most important pharmaceutical plants from Transylvania measured during 1986-1994 period presents high cesium radioactivity. The perennial plants (as Lichen Islandicus) for the same period accumulated a greater activity that the annual ones. Especially the lichen, because of the their slow decreasing activity are suitable as biological detectors also in retrospective measurements. Measuring the activity of some pollen samples was rediscovered. The pollen grains, during their transport in air by the bees, are acting like a filter for radionuclides so that we could use they to monitor the deliverance of these substances in air. (author)

Remediation of radioactively contaminated facilities and the site of Russian Research Center Kurchatov Institute

International Nuclear Information System (INIS)

Velikhov, E.P.; Ponomarev-Stepnoj, N.N.; Volkov, V.G.

2007-01-01

One discusses the efforts to rehabilitate the radiation hazard installations and to remediate the contaminated territory of the Kurchatov Institute RSC undertaken in 2006-2007 in terms of the Remediation Project. The old radwaste storage facilities constructed at the site when the Institute was involved in activities to elaborate both war and civil nuclear technologies were the basic objects of the rehabilitation efforts. Paper describes the structure of the storage facilities covering the volume and the characteristics of the stored radwaste. Paper discusses the storage facility site layout parameters taken into consideration in the course of the remediation efforts. Paper describes the procedures, the sequence of the remediation efforts and the peculiar features of the planning and engineering approaches. Paper dwells upon the results of the rehabilitation and the remediation efforts [ru

Radioactive ion beam facilities at INFN LNS

International Nuclear Information System (INIS)

Rifuggiato, D; Calabretta, L; Celona, L; Chines, F; Cosentino, L; Cuttone, G; Finocchiaro, P; Pappalardo, A; Re, M; Rovelli, A

2011-01-01

Radioactive ion beams are produced at INFN- Laboratori Nazionali del Sud (LNS) by means of the two operating accelerators, the Tandem and the Superconducting Cyclotron (CS), originally designed to accelerate stable beams. Both the ISOL (Isotope Separation On Line) and the IFF (In-Flight Fragmentation) methods are exploited to produce RIBs in two different ways at different energies: in the first case, the Cyclotron is the primary accelerator and the Tandem accelerates the secondary beams, while in the second case radioactive fragments are produced by the Cyclotron beam in a thin target with energies comparable to the primary beam energy. The ISOL facility is named EXCYT (Exotics at the Cyclotron and Tandem) and was commissioned in 2006, when the first radioactive beam ( 8 Li) has been produced. The IFF installation is named FRIBs (in Flight Radioactive Ion Beams), and it has started to produce radioactive beams in 2001, placing a thin target in the extraction beam line of the Cyclotron. The development of both facilities to produce and accelerate radioactive ion beams at LNS, is briefly described, with some details on the future prospects that are presently under consideration or realization.

Microfiltration of radioactive contaminants

Energy Technology Data Exchange (ETDEWEB)

Buckley, L P; Slade, J A; Vijayan, S; Wong, C F

1993-04-01

Cross-flow microfiltration processing of radioactive liquids has been in use at Chalk River Laboratories for about four years. The separation process removes suspended particles from radioactive waste solutions. The clean liquid can then be treated with conventional reverse osmosis membranes to achieve volume reduction factors approaching 100. Microfiltration removes particles below the rating of 0.2 microns, in part from particle agglomeration. Operating experience relating to a 15 USGPM unit is presented. Coupling microfiltration technology with chemical treatment enhances the removal of soluble species. Research and development experience with the removal of soluble contaminants found in ground water and waste water will be discussed. The technology has advantages over other membrane technologies, namely lower energy costs, a lesser degree of fouling, and a higher recovery of processed solution. Future applications of the technology are addressed. (author). 10 refs., 3 tabs., 4 figs.

Microfiltration of radioactive contaminants

International Nuclear Information System (INIS)

Buckley, L.P.; Slade, J.A.; Vijayan, S.; Wong, C.F.

1993-04-01

Cross-flow microfiltration processing of radioactive liquids has been in use at Chalk River Laboratories for about four years. The separation process removes suspended particles from radioactive waste solutions. The clean liquid can then be treated with conventional reverse osmosis membranes to achieve volume reduction factors approaching 100. Microfiltration removes particles below the rating of 0.2 microns, in part from particle agglomeration. Operating experience relating to a 15 USGPM unit is presented. Coupling microfiltration technology with chemical treatment enhances the removal of soluble species. Research and development experience with the removal of soluble contaminants found in ground water and waste water will be discussed. The technology has advantages over other membrane technologies, namely lower energy costs, a lesser degree of fouling, and a higher recovery of processed solution. Future applications of the technology are addressed. (author). 10 refs., 3 tabs., 4 figs

Argonne-West facility requirements for a radioactive waste treatment demonstration

International Nuclear Information System (INIS)

Dwight, C.C.; Felicione, F.S.; Black, D.B.; Kelso, R.B.; McClellan, G.C.

1995-01-01

At Argonne National Laboratory-West (ANL-W), near Idaho Falls, Idaho, facilities that were originally constructed to support the development of liquid-metal reactor technology are being used and/or modified to meet the environmental and waste management research needs of DOE. One example is the use of an Argonne-West facility to conduct a radioactive waste treatment demonstration through a cooperative project with Science Applications International Corporation (SAIC) and Lockheed Idaho Technologies Company. The Plasma Hearth Process (PBP) project will utilize commercially-adapted plasma arc technology to demonstrate treatment of actual mixed waste. The demonstration on radioactive waste will be conducted at Argonne's Transient Reactor Test Facility (TREAT). Utilization of an existing facility for a new and different application presents a unique set of issues in meeting applicable federal state, and local requirements as well as the additional constraints imposed by DOE Orders and ANL-W site requirements. This paper briefly describes the PHP radioactive demonstrations relevant to the interfaces with the TREAT facility. Safety, environmental design, and operational considerations pertinent to the PHP radioactive demonstration are specifically addressed herein. The personnel equipment, and facility interfaces associated with a radioactive waste treatment demonstration are an important aspect of the demonstration effort. Areas requiring significant effort in preparation for the PBP Project being conducted at the TREAT facility include confinement design, waste handling features, and sampling and analysis considerations. Information about the facility in which a radioactive demonstration will be conducted, specifically Argonne's TREAT facility in the case of PHP, may be of interest to other organizations involved in developing and demonstrating technologies for mixed waste treatment

Accelerator complex for a radioactive ion beam facility at ATLAS

International Nuclear Information System (INIS)

Nolen, J.A.

1995-01-01

Since the superconducting heavy ion linac ATLAS is an ideal post-accelerator for radioactive beams, plans are being developed for expansion of the facility with the addition of a driver accelerator, a production target/ion source combination, and a low q/m pre-accelerator for radioactive ions. A working group including staff from the ANL Physics Division and current ATLAS users are preparing a radioactive beam facility proposal. The present paper reviews the specifications of the accelerators required for the facility

An investigation of awareness on the Fukushima nuclear accident and Radioactive contamination

Energy Technology Data Exchange (ETDEWEB)

Ha, Jeong Chul; Song, Young Ju [Dept. of Consumer Safety, Korea Consumer Agency, Eumseong (Korea, Republic of)

2016-05-15

The objective of this study was to investigate Korean people's awareness about impact of the Fukushima nuclear power plant accident in Japan and radioactive contamination caused by it. The respondents of the survey were 600 adults who resided in the Seoul metropolitan area. The survey results show that the majority of respondents were concerned about impact of radiation leakage that might have an effect on our environment. They were worried about radioactive contamination of foodstuffs, particularly fishery products and preferred to acquire information through TV(49.8%) or the Internet(31.3%). Meanwhile, respondents mentioned that the information on the Fukushima nuclear accident and radioactive contamination had not been sufficient and they didn't know well about the follow-up measures of the government on the accident. Most respondents answered that information on radioactive contamination levels and safety of foods and environment was most needed. The results of this study could be useful to enhance awareness on radioactivity and improve risk communication on nuclear power plant accidents.

Design and development of food radioactivity contamination monitoring system

International Nuclear Information System (INIS)

Narayan, Pradeep; Vaijapurkar, S.G.; Bohra, Dinesh

2014-01-01

Radioactivity has been part and parcel of living being since the existence of the earth. It is available everywhere in our environment and being responsible for evolution of life on earth at some extent. However, the radioactivity in excess of the natural radioactive can have harmful effects on living being. The radiation exposure can be of external or internal origin or of both. The main route of internal radiation exposure is through the contaminated food chains. The concentration of natural radioactivity in food varies in range of 40-600 Bq/kg. 40 K being the single major radionuclide of food with typical radioactivity; 50 Bq/kg in milk, 420 Bq/kg in milk powder, 165 Bq/kg in potatoes, and 125 Bq/kg in beef is also the main contributor of natural radiation doses to human being. Measurement of radioactivity in food items and drinks is thus very important in controlling the internal exposure to human being especially in case of nuclear disaster. Though, the methods and techniques for food radioactivity measurement already existing, the need of portable instrument is warranted to measure the radioactivity in food items in raw form. Measurement of radioactivity may help in quick and mass screening of food items in case of nuclear emergencies. Any enhanced level of radioactivity in food items especially in case of nuclear emergency need to be evaluated for controlling its spread and restriction of consumption by the public. This way, it may help in managing internal radioactivity contamination to human being

Chernobyl three years later: radiobiologic evaluation of a radioactive contamination

International Nuclear Information System (INIS)

Behar, A.; Cohen-Boulakia, F.; Othmani, S.

1990-01-01

On April 26, 1986, after partial fusion and confining loss by explosion of a nuclear reactor, 5 x 10(7) Ci of radionuclides escaped from Chernobyl. Three years later, maps show contamination by radioactive isotopes (formed during that period) of 21,000 km2 of Soviet soil, mainly in Byelorussia and part of the Ukraine. Decontamination measures have not been effective to date and 135,000 persons are being followed medically, taking into account the radioactive doses they received. An initial excess of morbidity from solid tumors has been noted much sooner than in the case of Hiroshima and Nagasaki, but its significance is in dispute. Three years later, only the extent of the ecologic disaster caused by the radioactive contamination can be confirmed. It is too early to draw conclusions about radiation-induced carcinogenesis for the contaminated population

Allowable residual-contamination levels for decommissioning facilities in the 100 areas of the Hanford Site

International Nuclear Information System (INIS)

Kennedy, W.E. Jr.; Napier, B.A.

1983-07-01

This report contains the results of a study sponsored by UNC Nuclear Industries to determine Allowable Residual Contamination Levels (ARCL) for five generic categories of facilities in the 100 Areas of the Hanford Site. The purpose of this study is to provide ARCL data useful to UNC engineers in conducting safety and cost comparisons for decommissioning alternatives. The ARCL results are based on a scenario/exposure-pathway analysis and compliance with an annual dose limit for three specific modes of future use of the land and facilities. These modes of use are restricted, controlled, and unrestricted. The information on ARCL values for restricted and controlled use provided by this report is intended to permit a full consideration of decommissioning alternatives. ARCL results are presented both for surface contamination remaining in facilities (in dpm/100 cm 2 ), and for unconfined surface and confined subsurface soil conditions (in pCi/g). Two confined soil conditions are considered: contamination at depths between 1 and 4 m, and contamination at depths greater than or equal to 5 m. A set of worksheets are presented in an appendix for modifying the ARCL values to accommodate changes in the radionuclide mixture or concentrations, to consider the impacts of radioactive decay, and to predict instrument responses. Finally, a comparison is made between the unrestricted release ARCL values for the 100 Area facilities and existing decommissioning and land disposal regulations. For surface contamination, the comparison shows good agreement. For soil contamination, the comparison shows good agreement if reasonable modification factors are applied to account for the differences in modeling soil contamination and licensed low-level waste

Remediation and decommissioning of radioactive waste facilities in Estonia

International Nuclear Information System (INIS)

Putnik, H.; Realo, E.

2001-01-01

decommissioning and waste handling, e.g. creation of a waste treatment and conditioning facility, construction of an on-site interim storage for conditioned radioactive waste; Conditioning of solid operational waste in the dry storage and liquid waste tanks; Dismantling of contaminated installations; Declassification and demolition of useless facilities; Development of detailed decommissioning plans for the reactor systems. In the following short information is presented on the radioactive waste management and decommissioning projects carried out by ALARA Ltd at Paldiski after taking custody of the site. Project on conditioning of operational solid waste During the site operations solid radioactive waste was disposed in an on-site storage facility, SWS, which consisted of a concrete structure, divided into 10 cells. The former site operator has used three of these cells for storage of radioactive waste. Waste had been dumped into the facility without any conditioning or packaging and without any recorded inventory. The estimated waste volume in the SWS was about 100 m 3 including eight heat exchangers and 20 control rods from the repair and maintenance campaign of the reactor no I. The project started in 1996 with a radiological characterisation of the waste and continued with waste retrieval and conditioning. Depending on the radiological conditions, both remotely operated technique and manual retrieval was practiced. In summer 2000 the project was completed with demolition of the building after a full decontamination and declassification of the facility. During the project total 0.04 manSv was received by 16 persons, the maximum dose burden for a single person being 7.6 mSv. A more detailed description of this project was summarised in papers to international conferences WM'98 and ICEM'99. Project on conditioning of waste in liquid waste storage tanks Liquid radioactive waste was stored in the tanks of the Liquid Waste Treatment Facility (LWTF) and in the Liquid Waste Storage

The conceptual design of waste repository for radioactive waste from medical, industrial and research facilities containing comparatively high radioactivity

International Nuclear Information System (INIS)

Yamamoto, Masayuki; Hashimoto, Naro

2002-02-01

Advisory Committee on Nuclear Fuel Cycle Backend Policy reported the basic approach to the RI and Institute etc. wastes on March 2002. According to it, radioactive waste form medical, industrial and research facilities should be classified by their radioactivity properties and physical and chemical properties, and should be disposed in the appropriate types of repository with that classification. For the radioactive waste containing comparatively high radioactivity generated from reactors, NSC has established the Concentration limit for disposal. NSC is now discussing about the limit for the radioactive waste from medical, industrial and research facilities containing comparatively high radioactivity. Japan Nuclear Cycle Development Institute (JNC) preliminary studied about the repository for radioactive waste from medical, industrial and research facilities and discussed about the problems for design on H12. This study was started to consider those problems, and to develop the conceptual design of the repository for radioactive waste from medical, industrial and research facilities. Safety assessment for that repository is also performed. The result of this study showed that radioactive waste from medical, industrial and research facilities of high activity should be disposed in the repository that has higher performance of barrier system comparing with the vault type near surface facility. If the conditions of the natural barrier and the engineering barrier are clearer, optimization of the design will be possible. (author)

Characterization of radioactive contamination inside pipes with the Pipe Explorer trademark system

International Nuclear Information System (INIS)

Lowry, W.

1994-01-01

The objective for the development of the Pipe Explorer trademark radiological characterization system is to achieve a cost effective, low risk means of characterizing gamma radioactivity on the inside surface of pipes. The unique feature of this inspection system is the use of a pneumatically inflated impermeable membrane which transports the detector into the pipe as it inverts. The membrane's internal air pressure tows the detector and tether through the pipe. This mechanism isolates the detector and its cabling from the contaminated surface, yet allows measurement of radioactive emissions which can readily penetrate the thin plastic membrane material (such as gamma and high energy beta emissions). In Phase 1, an initial survey of DOE facilities was conducted to determine the physical and radiological characteristics of piping systems. The inverting membrane deployment system was designed and extensively tested in the laboratory. A range of membrane materials was tested to evaluate their ruggedness and deployment characteristics. Two different sizes of gamma scintillation detectors were procured and tested with calibrated sources. Radiation transport modeling evaluated the measurement system's sensitivity to detector position relative to the contaminated surface, the distribution of the contamination, background gamma levels, and gamma source energy levels. In the culmination of Phase 1, a field demonstration was conducted at the Idaho National Engineering Laboratory's Idaho Chemical Processing Plant. The project is currently in transition from Phase 1 to Phase 2, where more extensive demonstrations will occur at several sites. Results to date are discussed

Radioactive contamination, what actions for the polluted sites; Contamination radioactive, quelles actions pour les sites pollues

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

The nuclear safety authority and the direction of prevention of pollutions and risks have organised the first edition of the national colloquium: radioactive contamination: what actions for polluted sites. Four axes can be taken to follow this colloquium: prevention, outstanding tools to evaluate risks and rehabilitation, a better responsibility of operators and memory keeping. (N.C.)

Contamination and decontamination of vehicles when driven in radioactive areas

International Nuclear Information System (INIS)

Ulvsand, T.; Nygren, U.

1999-10-01

There is reason to ask whether it is beneficial to decontaminate vehicles, in view of the great effort applied. If the level of contamination is low before the decontamination process, then the cost is not motivated, even if the decontamination is shown to be effective in relative terms. The report describes two trials at the National NBC Defence School in Umeaa and one trial at the French test site in Bourges. The aim is to investigate how vehicles are contaminated and at which ground deposition levels troublesome levels of contamination will arise. In the trials, a non-radioactive agent substituting real radioactivity was used. The trials in Sweden so far have used the oversnow vehicle BV 206, during both winter and summer conditions. The vehicles were driven a specific distance along a road on which a known amount of the test substance had been dispersed. Samples were taken on pre-determined areas on one side of the vehicles to measure the amount of test substance. Later, the vehicles continued along a 'clean' road where additional samples were taken, but on the other side of the vehicles. The largest amount of test substance was collected on the tracks and on the back of the vehicle. The tracks and mud-flaps were effectively decontaminated when the vehicles were driven along a clean road, while most of the contamination remained on the backside. The purpose of the trials in France was to compare the results from our non-radioactive and their radioactive method, based on the radioactive La-140. Due to ground conditions, the level of contamination on the vehicles was much less than in the trials in Umeaa, but the effect decontamination could be measured after all

105-C Facility characterization plan

International Nuclear Information System (INIS)

Miller, R.L.

1997-01-01

This facility characterization plan is a site-specific document that describes how quantification and qualification of the radiological sources and the radioactive contamination in the 105-C Building will be accomplished. Characterization of hazardous materials will be addressed in a separate plan. This plan was developed from review of video tapes, photographs, and records. The purpose of this characterization plan is to provide an efficient and cost-effective method for determining the distribution of radioactive contamination at the 105-C Facility

Determination of external doses due to the melting of radioactively contaminated steel from nuclear facility in studsvik plant

International Nuclear Information System (INIS)

Brun-Yaba, Ch.; Menon, Sh.; Bjerler, J.; Wirendal, B.

2002-01-01

Radioactively contaminated material arises in many industries, both nuclear and non-nuclear. This material may be re-used, recycled or disposed of in a landfill. This project deals with low-level contaminated scrap recycling in a melting plant. The purpose is to register the radiation dose uptake by workers in the melting plant for practical scenarios and to compare these values to the results of computer calculation code for the same scenarios. In a recent past, dose evaluation studies have been done with codes but, often, the predictions are not exactly compared with the industrial practices measurements

Proposed sale of radioactively contaminated nickel ingots located at the Paducah Gaseous Diffusion Plant, Paducah, Kentucky

International Nuclear Information System (INIS)

1995-10-01

The U.S. Department of Energy (DOE) proposes to sell 8,500 radioactively contaminated nickel ingots (9.350 short tons), currently in open storage at the Paducah Gaseous Diffusion Plant (PGDP), to Scientific Ecology Group, Inc. (SEG) for decontamination and resale on the international market. SEG would take ownership of the ingots when they are loaded for transport by truck to its facility in Oak Ridge, Tennessee. SEG would receive approximately 200 short tons per month over approximately 48 months (an average of 180 ingots per month). The nickel decontamination process specified in SEG's technical proposal is considered the best available technology and has been demonstrated in prototype at SEG. The resultant metal for resale would have contamination levels between 0.3 and 20 becquerel per gram (Bq/g). The health hazards associated with release of the decontaminated nickel are minimal. The activity concentration of the end product would be further reduced when the nickel is combined with other metals to make stainless steel. Low-level radioactive waste from the SEG decontamination process, estimated to be approximately 382 m 3 (12,730 ft), would be shipped to a licensed commercial or DOE disposal facility. If the waste were packaged in 0.23 m 3 -(7.5 ft 3 -) capacity drums, approximately 1,500 to 1,900 drums would be transported over the 48-month contract period. Impacts from the construction of decontamination facilities and the selected site are minimal

Treatment techniques for the removal of radioactive contaminants from drinking water

International Nuclear Information System (INIS)

Logsdon, Gary S.

1978-01-01

Maximum contaminant levels have been set for radioactive contaminants, as required by the Safe Drinking Water Act (PL 93-523). Treatment techniques are available for removing radium and beta-gamma emitters. Presently-used methods of removing radium-226 are precipitative lime softening (80-90% removal) ion exchange softening (95% removal) and reverse osmosis (95% removal). The 5 p Ci/l limit for radium can be met with conventional technology for raw waters in the 5-100 p Ci/l concentration range. Treatment for removal of beta or gamma emitters must be based upon chemical rather than radioactive characteristics of the contaminant. Reverse osmosis can remove a broad spectrum of ions and molecules from water, so it is the process most likely to be used. The maximum contaminant level for beta and gamma radioactivity is an annual dose equivalent to the total body or any organ not to exceed 4 m rem/year. The fate of radionuclides after removal from drinking water should be considered. Presently radium is disposed with other process wastes at softening plants removing radium. Confinement and disposal as a radioactive waste would be very expensive. (author)

Evaluation of the costs and benefits of recycling radioactively contaminated scrap metal

International Nuclear Information System (INIS)

Durman, E.C.; Tsirigotis, P.; MacKinney, J.A.

1995-01-01

The U.S. Environmental Protection Agency (EPA) is evaluating the economic and technical issues associated with the potential recycling of radioactive scrap metals (RSM). These metals, usually only slightly contaminated, originate primarily from the decommissioning and decontamination (D and D) of federal facilities, licensees of the Nuclear Regulatory Commission, and certain unlicensed industries. EPA conducted a study entitled Analysis of the Potential Recycling of Department of Energy Radioactive Scrap Metal, September 6, 1994, for the U.S. Department of Energy (DOE) to provide information and tools to DOE for assessing DOE's problem with RSM from the D and D of their sites. EPA is now initiating an evaluation of RSM recycling to support a recycling regulation. Although the study prepared for DOE will provide a useful start for the regulatory analysis, additional information must be gathered to analyze the impacts of a recycling regulation that will apply to all potential generators of RSM. This paper summarizes cost-benefit issues related to an RSM recycling regulatory analysis, including: the quantity of potentially recyclable contaminated metals; costs of disposal at federal and private waste repositories; all potential environmental, health, and safety, and market impacts; and the potential for adverse effects on radio-sensitive industries. (author)

Radioactive waste management in a fuel reprocessing facility in fiscal 1982

International Nuclear Information System (INIS)

1984-01-01

In the fuel reprocessing facility of the Power Reactor and Nuclear Fuel Development Corporation, radioactive gaseous and liquid waste are released not exceeding the respective permissible levels. Radioactive concentrated solutions are stored at the site. Radioactive solid waste are stored appropriately at the site. In fiscal 1982, the released quantities of radioactive gaseous and liquid waste were both below the permissible levels. The results of radioactive waste management in the fuel reprocessing facility in fiscal 1982 are given in the tables: the released quantities of radioactive gaseous and liquid waste, the produced quantities of radioactive solid waste, and the stored quantities of radioactive concentrated solutions and of radioactive solid waste as of the end of fiscal 1982. (Mori, K.)

Protecting Lake Ontario - Treating Wastewater from the Remediated Low-Level Radioactive Waste Management Facility - 13227

International Nuclear Information System (INIS)

Freihammer, Till; Chaput, Barb; Vandergaast, Gary; Arey, Jimi

2013-01-01

The Port Granby Project is part of the larger Port Hope Area Initiative, a community-based program for the development and implementation of a safe, local, long-term management solution for historic low level radioactive waste (LLRW) and marginally contaminated soils (MCS). The Port Granby Project involves the relocation and remediation of up to 0.45 million cubic metres of such waste from the current Port Granby Waste Management Facility located in the Municipality of Clarington, Ontario, adjacent to the shoreline of Lake Ontario. The waste material will be transferred to a new suitably engineered Long-Term Waste Management Facility (LTWMF) to be located inland approximately 700 m from the existing site. The development of the LTWMF will include construction and commissioning of a new Wastewater Treatment Plant (WWTP) designed to treat wastewater consisting of contaminated surface run off and leachate generated during the site remediation process at the Port Granby Waste Management Facility as well as long-term leachate generated at the new LTWMF. Numerous factors will influence the variable wastewater flow rates and influent loads to the new WWTP during remediation. The treatment processes will be comprised of equalization to minimize impacts from hydraulic peaks, fine screening, membrane bioreactor technology, and reverse osmosis. The residuals treatment will comprise of lime precipitation, thickening, dewatering, evaporation and drying. The distribution of the concentration of uranium and radium - 226 over the various process streams in the WWTP was estimated. This information was used to assess potential worker exposure to radioactivity in the various process areas. A mass balance approach was used to assess the distribution of uranium and radium - 226, by applying individual contaminant removal rates for each process element of the WTP, based on pilot scale results and experience-based assumptions. The mass balance calculations were repeated for various flow

Protecting Lake Ontario - Treating Wastewater from the Remediated Low-Level Radioactive Waste Management Facility - 13227

Energy Technology Data Exchange (ETDEWEB)

Freihammer, Till; Chaput, Barb [AECOM, 99 Commerce Drive, Winnipeg, Manitoba, R3P 0Y7 (Canada); Vandergaast, Gary [Atomic Energy of Canada Limited, Port Hope, Ontario (Canada); Arey, Jimi [Public Works and Government Services Canada, Ontario (Canada)

2013-07-01

The Port Granby Project is part of the larger Port Hope Area Initiative, a community-based program for the development and implementation of a safe, local, long-term management solution for historic low level radioactive waste (LLRW) and marginally contaminated soils (MCS). The Port Granby Project involves the relocation and remediation of up to 0.45 million cubic metres of such waste from the current Port Granby Waste Management Facility located in the Municipality of Clarington, Ontario, adjacent to the shoreline of Lake Ontario. The waste material will be transferred to a new suitably engineered Long-Term Waste Management Facility (LTWMF) to be located inland approximately 700 m from the existing site. The development of the LTWMF will include construction and commissioning of a new Wastewater Treatment Plant (WWTP) designed to treat wastewater consisting of contaminated surface run off and leachate generated during the site remediation process at the Port Granby Waste Management Facility as well as long-term leachate generated at the new LTWMF. Numerous factors will influence the variable wastewater flow rates and influent loads to the new WWTP during remediation. The treatment processes will be comprised of equalization to minimize impacts from hydraulic peaks, fine screening, membrane bioreactor technology, and reverse osmosis. The residuals treatment will comprise of lime precipitation, thickening, dewatering, evaporation and drying. The distribution of the concentration of uranium and radium - 226 over the various process streams in the WWTP was estimated. This information was used to assess potential worker exposure to radioactivity in the various process areas. A mass balance approach was used to assess the distribution of uranium and radium - 226, by applying individual contaminant removal rates for each process element of the WTP, based on pilot scale results and experience-based assumptions. The mass balance calculations were repeated for various flow

Defense Waste Processing Facility -- Radioactive operations -- Part 3 -- Remote operations

International Nuclear Information System (INIS)

Barnes, W.M.; Kerley, W.D.; Hughes, P.D.

1997-01-01

The Savannah River Site's Defense Waste Processing Facility (DWPF) near Aiken, South Carolina is the nation's first and world's largest vitrification facility. Following a ten year construction period and nearly three years of non-radioactive testing, the DWPF began radioactive operations in March 1996. Radioactive glass is poured from the joule heated melter into the stainless steel canisters. The canisters are then temporarily sealed, decontaminated, resistance welded for final closure, and transported to an interim storage facility. All of these operations are conducted remotely with equipment specially designed for these processes. This paper reviews canister processing during the first nine months of radioactive operations at DWPF. The fundamental design consideration for DWPF remote canister processing and handling equipment are discussed as well as interim canister storage

Development of plastic scintillator based food radioactivity contamination monitoring system

International Nuclear Information System (INIS)

Parihar, A.; Sahani, R.M.; Mahala, V.K.; Vaijapurkar, S.G.

2016-01-01

Radioactivity is naturally present in soil, water and food stuffs. Food can be contaminated after discharge of radioactivity into the environment from industries that concentrate natural radionuclide and from civil or military nuclear operations. The contamination can be in three ways; by direct deposition, through the food chain and induced radioactivity due to exposure of high neutron flux. The health effects on human depend on the type of radionuclide and the length of time people are exposed to it. The studies of fission product behaviour in the food chain have revealed radionuclide Strontium-90, Caesium 137 and Iodine-131 are of major concern. Plastic scintillator is already developed indigenously at Defence Laboratory, Jodhpur. Efforts has been made to develop a portable field instrument using plastic scintillator for assessment of beta ( 90 Sr) and gamma ( 137 Cs and 131 I) radioactivity in food

DOE`s radioactively - contaminated metal recycling: The policy and its implementation

Energy Technology Data Exchange (ETDEWEB)

Warren, S.; Rizkalla, E.

1997-02-01

In 1994, the Department of Energy`s Office of Environmental Restoration initiated development of a recycling policy to minimize the amount of radioactively-contaminated metal being disposed of as waste. During the following two years, stakeholders (including DOE and contractor personnel, regulators, members of the public, and representatives of labor and industry) were invited to identify key issues of concern, and to provide input on the final policy. As a result of this process, a demonstration policy for recycling radioactively-contaminated carbon steel resulting from decommissioning activities within the Environmental Management program was signed on September 20, 1996. It specifically recognizes that the Office of Environmental Management has a tremendous opportunity to minimize the disposal of metals as waste by the use of disposal containers fabricated from contaminated steel. The policy further recognizes the program`s demand for disposal containers, and it`s role as the major generator of radioactively-contaminated steel.

ISOL science at the Holifield Radioactive Ion Beam Facility

Energy Technology Data Exchange (ETDEWEB)

Beene, James R [ORNL; Bardayan, Daniel W [ORNL; Galindo-Uribarri, Alfredo {nmn} [ORNL; Gross, Carl J [ORNL; Jones, K. L. [University of Tennessee, Knoxville (UTK); Liang, J Felix [ORNL; Nazarewicz, Witold [ORNL; Stracener, Daniel W [ORNL; Tatum, B Alan [ORNL; Varner Jr, Robert L [ORNL

2011-01-01

The Holi eld Radioactive Ion Beam Facility, located in Oak Ridge, Tennessee, is operated as a National User Facility for the U.S. Department of Energy, producing high quality ISOL beams of short-lived, radioactive nuclei for studies of exotic nuclei, astrophysics research, and various societal applications. The primary driver, the Oak Ridge Isochronous Cyclotron, produces rare isotopes by bombarding highly refractory targets with light ions. The radioactive isotopes are ionized, formed into a beam, mass selected, injected into the 25-MV Tandem, accelerated, and used in experiments. This article reviews HRIBF and its science.

Radioactive Mapping Contaminant of Alpha on The Air in Space of Repair of Hot Cell and Medium Radioactivity Laboratory in Radio metallurgy Installation

International Nuclear Information System (INIS)

Yusuf-Nampira; Endang-Sukesi; S-Wahyuningsih; R-Budi-Santoso

2007-01-01

Hot cell and space of acid laboratory medium activity in Radio metallurgy Installation are used for the examination preparation of fuel nuclear post irradiation. The sample examined is dangerous radioactive material representing which can disseminate passing air stream. The dangerous material spreading can be pursued by arranging air stream from laboratory space to examination space. To know the performance the air stream arrangement is hence conducted by radioactive mapping contaminant of alpha in laboratory / space of activity place, for example, medium activity laboratory and repair space. This mapping radioactivity contaminant is executed with the measurement level of the radioactivity from sample air taken at various height with the distance of 1 m, various distance and from potential source as contaminant spreading access. The mapping result indicate that a little spreading of radioactive material happened from acid cupboard locker to laboratory activity up to distance of 3 m from acid cupboard locker and spreading of radioactive contaminant from goods access door of the hot cell 104 to repair space reach the distance of 2 m from goods door access. Level of the radioactive contamination in the space was far under maximum limitation allowed (20 Bq / m 3 ). (author)

Method of decontaminating radioactive-contaminated instruments

Energy Technology Data Exchange (ETDEWEB)

Urata, M; Fujii, M; Kitaguchi, H

1982-03-29

Purpose: To enable safety processing of liquid wastes by recovering radioactive metal ions remaining in the electrolytes after the decontamination procedure thereby decreasing the radioactivity. Method: In a decontamination tank containing electrolytes consisting of diluted hydrochloric acid and diluted sulfuric acid, are provided a radioactive contaminated instrument connected to an anode and a collector electrode made of stainless steel connected to a cathode respectively. Upon applying electrical current, the portion of the mother material to be decontaminated is polished electrolytically into metal ions and they are deposited as metal on the collection electrode. After completion of the decontamination, an ultrasonic wave generator is operated to strip and remove the oxide films. Thereafter, the anode is replaced with the carbon electrode and electrical current is supplied continuously, whereby the remaining metal ions are deposited and recovered as the metal on the collection electrode.

Predicting the radioactive contamination of the surroundings near a nuclear power plant

Energy Technology Data Exchange (ETDEWEB)

Khristova, M; Paskalev, Z

1975-01-01

Predicting the radioactive contamination requires determining the concentration of radioactive material emitted from the stack of a nuclear power plant into the air and deposited on the earth's surface. The main factors determining the degree of contamination are the distance from the stack, the wind velocity and air turbulence. Formulas are presented for predicting the amount of radioactivity as a function of the initial concentration of activity, the distance from the stack and the meteorological condition. Formulas are given for the maximum deposition of radioactive aerosols at a distance R from the stack under wet and dry condtions. 2 refs. (SJR)

Environmental remediation. Strategies and techniques for cleaning radioactively contaminated sites

International Nuclear Information System (INIS)

Falck, W. Eberhard

2001-01-01

Actions for a cleaner and safety environment have risen on social and political agendas in recent years. They include efforts to remediate contaminated sites posing a radiological risk to humans and the surrounding environment. Radiological risks can result from a variety of nuclear and non-nuclear activities. They include: nuclear or radiological accidents; nuclear weapons production and testing; poor radioactive waste management and disposal practices; industrial manufacturing involving radioactive materials; conventional mining and milling of ores and other production processes, e.g. oil and gas production, resulting in enhanced concentrations of naturally occurring radioactive materials (NORMs). The IAEA has developed a comprehensive programme directed at the remediation of radioactively contaminated sites. The programme collates and distributes knowledge about contaminated sites; appropriate methods for their characterization; assessment of their potential environmental and radiological impact; and applicable methods for their clean-up, following internationally recommended safety criteria. The overall resources, and which are technologically less advanced, to focus their efforts and chose appropriate strategies for the abatement or removal of exposure to radiation. An important aspect is the intention to 'close the loop' in the nuclear fuel cycle in the interests of sustainable energy development including nuclear power

Disposal facilities for radioactive waste - legislative requirements for siting

International Nuclear Information System (INIS)

Markova-Mihaylova, Radosveta

2015-01-01

The specifics of radioactive waste, namely the content of radionuclides require the implementation of measures to protect human health and the environment against the hazards arising from ionizing radiation, including disposal of waste in appropriate facilities. The legislative requirements for siting of such facilities, and classification of radioactive waste, as well as the disposal methods, are presented in this publication

Rapid Evaluation of Radioactive Contamination in Rare Earth Mine Mining

Science.gov (United States)

Wang, N.

2017-12-01

In order to estimate the current levels of environmental radioactivity in Bayan Obo rare earth mine and to study the rapid evaluation methods of radioactivity contamination in the rare earth mine, the surveys of the in-situ gamma-ray spectrometry and gamma dose rate measurement were carried out around the mining area and living area. The in-situ gamma-ray spectrometer was composed of a scintillation detector of NaI(Tl) (Φ75mm×75mm) and a multichannel analyzer. Our survey results in Bayan Obo Mine display: (1) Thorium-232 is the radioactive contamination source of this region, and uranium-238 and potassium - 40 is at the background level. (2) The average content of thorium-232 in the slag of the tailings dam in Bayan Obo is as high as 276 mg/kg, which is 37 times as the global average value of thorium content. (3) We found that the thorium-232 content in the soil in the living area near the mining is higher than that in the local soil in Guyang County. The average thorium-232 concentrations in the mining areas of the Bayan Obo Mine and the living areas of the Bayan Obo Town were 18.7±7.5 and 26.2±9.1 mg/kg, respectively. (4) It was observed that thorium-232 was abnormal distributed in the contaminated area near the tailings dam. Our preliminary research results show that the in-situ gamma-ray spectrometry is an effective approach of fast evaluating rare earths radioactive pollution, not only can the scene to determine the types of radioactive contamination source, but also to measure the radioactivity concentration of thorium and uranium in soil. The environmental radioactive evaluation of rare earth ore and tailings dam in open-pit mining is also needed. The research was supported by National Natural Science Foundation of China (No. 41674111).

Inductively coupled plasma mass spectrometer installation modifications in a radioactive contaminated laboratory for the analysis of DOE radioactive waste streams

International Nuclear Information System (INIS)

Giaquinto, J.M.; Keller, J.M.; Meeks, A.M.

1998-01-01

The operation and maintenance of a complex analytical instrument such as an inductively coupled plasma mass spectrometer in a radioactive contaminated environment presents unique problems and challenges that have to be considered in the purchasing and installation process. Considerations such as vendor experience, typical radiation levels, sample matrices encountered during sample analysis, instrument accessibility for maintenance, and upkeep must be incorporated into the decision process. The Radioactive Materials Analytical Laboratory (RMAL) at Oak Ridge National Laboratory (ORNL) recently purchased and installed an inductively coupled plasma mass spectrometer for the analysis of Department of Energy (DOE) radioactive waste streams. This presentation will outline the purchasing decision, installation of the instrument, and how the modifications needed to operate in a radioactive contaminated laboratory do not significantly impact the daily operation and maintenance requirements of the instrument. Also, a contamination survey of the system will be presented which demonstrates the contamination levels in the instrument from the sample introduction system to the detector. (author)

Inductively coupled plasma mass spectrometer installation modifications in a radioactive contaminated laboratory for the analysis of DOE radioactive waste streams

International Nuclear Information System (INIS)

Giaquinto, J.M.; Keller, J.M.; Meeks, A.M.

1997-04-01

The operation and maintenance of a complex analytical instrument such as an inductively coupled plasma mass spectrometer in a radioactive contaminated environment presents unique problems and challenges that have to be considered in the purchasing and installation process. Considerations such as vendor experience, typical radiation levels, sample matrices encountered during sample analysis, instrument accessibility for maintenance, and upkeep must be incorporated into the decision process. The Radioactive Materials Analytical Laboratory (RMAL) at Oak Ridge National Laboratory (ORNL) recently purchased and installed an inductively coupled plasma mass spectrometer for the analysis of Department of Energy (DOE) radioactive waste streams. This presentation will outline the purchasing decision, installation of the instrument, and how the modifications needed to operate in a radioactive contaminated laboratory do not significantly impact the daily operation and maintenance requirements of the instrument. Also, a contamination survey of the system will be presented which demonstrates the contamination levels in the instrument from the sample introduction system to the detector

Characterization and remediation of highly radioactive contaminated soil at Hanford

International Nuclear Information System (INIS)

Buckmaster, M.A.; Erickson, J.K.

1993-09-01

The Hanford Site, Richland, Washington, contains over 1,500 identified waste sites and numerous groundwater plumes that will be characterized and remediated over the next 30 years. As a result of the Hanford Federal Facility Agreement and Consent Order, the US Department of Energy (DOE) has initiated a remedial investigation/feasibility study (RI/FS) at the 200-BP-1 operable unit. The 200-BP-1 RI/FS is the first Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) investigation on the Hanford Site that involves highly radioactive and chemically contaminated soils. The initial phase of site characterization was designed to assess the nature and extent of contamination associated with the source waste sites within the 200-BP-1 operable unit. Characterization activities consisted of drilling and sampling, chemical and physical analysis of samples, and development of a conceptual vadose zone model. These data were then used. to develop remedial alternatives during the FS evaluation. The preferred alternative resulting from the RI/FS process for the 200-BP-1 operable unit is to construct a surface isolation barrier. The multi-layered earthen barrier will be designed to prevent migration of contaminants resulting from water infiltration, biointrusion, and wind and water erosion

Evaluation of indigenously developed plastic scintillator sheet detector for surface radioactive contamination monitoring application

International Nuclear Information System (INIS)

Sahani, R.M.; Chaudhary, H.S.; Mahala, V.K.; Senwar, K.R.; Meena, J.P.

2018-01-01

Radioactive contamination may be caused by release of radioactivity in the environment due to accident at nuclear plant/reactor or spillage of loose radioactive materials in a laboratory. The protection of workers from potentially hazardous radiations emitted by the contaminants is a matter of prime concern. The detection of such radiations requires a monitoring system capable of measuring the level of radioactivity at the contaminated site. Plastic scintillators are widely used for large area radiation monitoring due to the ease of preparation in different shape and sizes. These detectors are sensitive to beta and gamma radiation therefore can be used for monitoring of beta and gamma contamination. In this paper, performance results of indigenously developed plastic scintillator sheet of area 800 cm 2 are reported

Evaluation of ultrafiltration membranes for treating low-level radioactive contaminated liquid waste

International Nuclear Information System (INIS)

Koenst, J.W.; Roberts, R.C.

1978-01-01

A series of experiments were performed on Waste Disposal Facility (WD) influent using Romicon hollow fiber ultrafiltration modules with molecular weight cutoffs ranging from 2000 to 80,000. The rejection of conductivity was low in most cases. The rejection of radioactivity ranged from 90 to 98%, depending on the membrane type and on the feed concentration. Typical product activity ranged from 7 to 100 dis/min/ml of alpha radiation. Experiments were also performed on alpha-contaminated laundry wastewater. Results ranged from 98 to >99.8%, depending on the membrane type. This yielded a product concentration of less than 0.1 dis/min/ml of alpha radiation. Tests on PP-Building decontamination water yielded rejections of 85 to 88% alpha radiation depending on the membrane type. These experiments show that the ability to remove radioactivity by membrane is a function of the contents of the waste stream because the radioactivity in the wastewater is in various forms: ionic, polymeric, colloidal, and absorbed onto suspended solids. Although removal of suspended or colloidal material is very high, removal of ionic material is not as effective. Alpha-contaminated laundry wastewater proved to be the easiest to decontaminate, whereas the low-level PP-Building decontamination water proved to be the most difficult to decontaminate. Decontamination of the WD influent, a combined waste stream, varied considerably from day to day because of its constantly changing makeup. The WD influent was also treated with various substances, such as polyelectrolytes, complexing agents, and coagulants, to determine if these additives would aid in the removal of radioactive material from the various wastewaters by complexing the ionic species. At the present time, none of the additives evaluated has had much effect; but experiments are continuing

Dismantling an alpha-contaminated facility

International Nuclear Information System (INIS)

Caldwell, R.D.; Harper, R.M.

1975-01-01

The difficult task of removing large pieces of highly contaminated equipment from an obsolete plutonium-239 facility was completed in a seven-month operation that included structural alteration of the process building. Detailed job planning, job execution and contamination control were major factors in accomplishing the task

Prospects for high-power radioactive beam facilities worldwide

CERN Document Server

Nolen, Jerry A

2003-01-01

Advances in accelerators, targets, ion sources, and experimental instrumentation are making possible ever more powerful facilities for basic and applied research with short-lived radioactive isotopes. There are several current generation facilities, based on a variety of technologies, operating worldwide. These include, for example, those based on the in-flight method such as the recently upgraded National Superconducting Cyclotron Laboratory at Michigan State University, the facility at RIKEN in Japan, GANIL in Caen, France, and GSI in Darmstadt, Germany. Present facilities based on the Isotope-Separator On-Line method include, for example, the ISOLDE laboratory at CERN, HRIBF at Oak Ridge, and the new high-power facility ISAC at TRIUMF in Vancouver. Next-generation facilities include the Radioactive-Ion Factory upgrade of RIKEN to higher energy and intensity and the upgrade of ISAC to a higher energy secondary beam; both of these projects are in progress. A new project, LINAG, to upgrade the capabilities at...

Sources contributing to radioactive contamination of the Techa river and areas surrounding the Mayak production association, Urals, Russia

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

A Russian-Norwegian expert group has performed joint investigations of possible impacts of the Mayak plant on the contamination of the Arctic Ocean. This plant that was the first in the former Soviet Union to produce nuclear weapons material, had five special nuclear reactors for production of plutonium and a facility for separation of the plutonium as weapons material. A system of dams along the upper part of Techa River was constructed in order to retain most of the radioactivity, creating several artificial water reservoirs along the old river bed. The paper describes the results of the investigations of the working group. it is concluded that sediment samples from reservoir No. 10 and 11, and from the floodplain along the upper Techa River, have the highest radioactivities (more than 2 MBq/kg d.w. of cesium-137). Flooding of the surrounding swamp and rupture in the reservoirs may cause substantial releases to the river system and thus contaminate the Arctic waters. Also transport of radioactivity by underground water from the reservoirs may contaminate the river system. The future work of the group will be focussed on risk assessment of potential accident scenarios, and possible long-term consequences for man and the environment. 21 refs.

Sources contributing to radioactive contamination of the Techa river and areas surrounding the Mayak production association, Urals, Russia

International Nuclear Information System (INIS)

1997-01-01

A Russian-Norwegian expert group has performed joint investigations of possible impacts of the Mayak plant on the contamination of the Arctic Ocean. This plant that was the first in the former Soviet Union to produce nuclear weapons material, had five special nuclear reactors for production of plutonium and a facility for separation of the plutonium as weapons material. A system of dams along the upper part of Techa River was constructed in order to retain most of the radioactivity, creating several artificial water reservoirs along the old river bed. The paper describes the results of the investigations of the working group. it is concluded that sediment samples from reservoir No. 10 and 11, and from the floodplain along the upper Techa River, have the highest radioactivities (more than 2 MBq/kg d.w. of cesium-137). Flooding of the surrounding swamp and rupture in the reservoirs may cause substantial releases to the river system and thus contaminate the Arctic waters. Also transport of radioactivity by underground water from the reservoirs may contaminate the river system. The future work of the group will be focussed on risk assessment of potential accident scenarios, and possible long-term consequences for man and the environment. 21 refs

Status of the Japan's regulatory policy on radioactive waste management. Cleanup and recycling issues

International Nuclear Information System (INIS)

Takeuchi, Daiji

1995-01-01

Wastes from nuclear facilities are very diversified concerning that have different levels of radioactivity and include different kinds of radioactive materials. Besides some of those waste is not assumed as radioactive waste. The basic policy of the radioactive waste management is taking that diversity into full account for appropriate separate management of different types of radioactive waste and treatment and disposal of each type in a rational manner, including recycling. From the point, the disposal methods are considered or under consideration to that waste, (1) from nuclear reactor facility, (2) from nuclear fuel cycle facility--HLW, waste contaminated TRU nuclides, or contaminated uranium, (3) from RI utilization or research institute, and (4) from decommissioning of nuclear facility. Now in Japan, regulation framework for some kind of LLW from reactor facility, including waste from decommissioning of reactor is established. (J.P.N.)

Radioactive contamination of natural and artificial materials

International Nuclear Information System (INIS)

Kovalchuk, E.L.; Pomansky, A.A.; Smolnikov, A.A.; Temmoev, A.H.

1980-01-01

The gamma radiation of different materials was measured in an underground low-background chamber with extraordinary background characteristics. The excellent background conditions of the measurements enabled investigators to see the alpha-particle peaks of the internal radioactive contamination of NaI(Tl) detectors, which were especially made for these measurements. The sensitivity limit of the installation was determined by the internal contamination of the NaI(Tl) detectors alone. Any radiation background, except for three substances, tungsten, copper, and brass, could be registered

Decommissioning Strategies Selection for Facilities Using Radioactive Material

International Nuclear Information System (INIS)

Husen Zamroni; Jaka Rachmadetin

2008-01-01

The facilities using radioactive material that have been stopped operation will require some form of the decommissioning for public and environment safety. The approaches are identified by three decommissioning strategies: immediate dismantling, deferred dismantling and entombment. If a facility undergoes immediate dismantling, most radio nuclides will have no such sufficient time to decay and therefore this strategy may not provide reduction in the worker exposure. A facility that undergoes deferred dismantling may advantage from the radioactive decay of residual radio nuclides during the long term storage period and entombment could be a viable option for other nuclear facilities containing only short lived or limited concentrations of long lived radionuclides. Mostly, only two types of the decommissioning used to be done in the world, immediate and deferred dismantling. (author)

The supposed radioactive contamination of the Puelche aquifer

International Nuclear Information System (INIS)

Martini, Leopoldo E.

2005-01-01

The paper attempts to clarify the supposed radioactive contamination of the Puelche Aquifer in the Ezeiza Atomic Center Area, Ezeiza, province of Buenos Aires (Argentina). Reports are listed that show categorically that no anthropogenic uranium contamination is present. As far as the nitrates contamination is concerned, it is not generated by the Ezeiza Atomic Center, because the Center is downward from the contaminated zone. It is possible that the contamination is produced by houses in the area without suitable sewage. In the present case the best contribution to the environmental right, besides the adaptation and the systematization of the different legal instruments, is to found the analysis of the facts on the scientific and technical knowledge. (author) [es

Holifield Radioactive Ion Beam Facility Development and Status

CERN Document Server

Tatum, Alan

2005-01-01

The Holifield Radioactive Ion Beam Facility (HRIBF) is a national user facility dedicated to nuclear structure, reactions, and nuclear astrophysics research with radioactive ion beams (RIBs) using the isotope separator on-line (ISOL) technique. An integrated strategic plan for physics, experimental systems, and RIB production facilities have been developed and implementation of the plan is under way. Specific research objectives are defined for studying the nature of nucleonic matter, the origin of elements, solar physics, and synthesis of heavy elements. Experimental systems upgrade plans include new detector arrays and beam lines, and expansion and upgrade of existing devices. A multifaceted facility expansion plan includes a $4.75M High Power Target Laboratory (HPTL), presently under construction, to provide a facility for testing new target materials, target geometries, ion sources, and beam preparation techniques. Additional planned upgrades include a second RIB production system (IRIS2), an external axi...

Method of melting and decontaminating radioactive contaminated aluminum material

International Nuclear Information System (INIS)

Uda, Tatsuhiko; Miura, Noboru; Kawasaki, Katsuo; Iba, Hajime.

1986-01-01

Purpose: To improve the decontaminating efficiency upon melting decontamination of radioactive-contaminated aluminum materials. Method: This invention concerns an improvement for the method of melting decontamination by adding slug agent composed of organic compound to contaminated aluminum material and extracting the radioactive materials into the slug thereby decontaminating the aluminum material. Specifically metals effective for reducing the active amount of aluminum are added such that the content is greater than a predetermined value in the heat melting process. The metal comprises Mg, Cu or a mixture thereof and the content is more than 4 % including those previously contained in the aluminum material. (Ikeda, J.)

Method of decontaminating radioactive-contaminated instruments

International Nuclear Information System (INIS)

Urata, Megumu; Fujii, Masaaki; Kitaguchi, Hiroshi.

1982-01-01

Purpose: To enable safety processing of liquid wastes by recovering radioactive metal ions remaining in the electrolytes after the decontamination procedure thereby decreasing the radioactivity. Method: In a decontamination tank containing electrolytes consisting of diluted hydrochloric acid and diluted sulfuric acid, are provided a radioactive contaminated instrument connected to an anode and a collector electrode made of stainless steel connected to a cathode respectively. Upon applying electrical current, the portion of the mother material to be decontaminated is polished electrolytically into metal ions and they are deposited as metal on the collection electrode. After completion of the decontamination, an ultrasonic wave generator is operated to strip and remove the oxide films. Thereafter, the anode is replaced with the carbon electrode and electrical current is supplied continuously, whereby the remaining metal ions are deposited and recovered as the metal on the collection electrode. (Yoshino, Y.)

Radioactive contamination of the biosphere and consequences for food supply

International Nuclear Information System (INIS)

Wiechen, A.

1989-01-01

The paper deals with all aspects of radioactive contamination of the biosphere and corresponding consequences for food supply. In particular, releases of radioactivity by nuclear weapon tests in the early 60's and nuclear accidents in recent years are discussed. Contamination of food in the Federal Republic of Germany by these events and corresponding ingestion dose are demonstrated using examples. Furthermore diffusion of radionuclides and their transfer through the food chains to man are described. Suitable methods of decontamination at different production steps and their viability are discussed. (orig.) [de

Low-level radioactive waste disposal facility closure

International Nuclear Information System (INIS)

White, G.J.; Ferns, T.W.; Otis, M.D.; Marts, S.T.; DeHaan, M.S.; Schwaller, R.G.; White, G.J.

1990-11-01

Part I of this report describes and evaluates potential impacts associated with changes in environmental conditions on a low-level radioactive waste disposal site over a long period of time. Ecological processes are discussed and baselines are established consistent with their potential for causing a significant impact to low-level radioactive waste facility. A variety of factors that might disrupt or act on long-term predictions are evaluated including biological, chemical, and physical phenomena of both natural and anthropogenic origin. These factors are then applied to six existing, yet very different, low-level radioactive waste sites. A summary and recommendations for future site characterization and monitoring activities is given for application to potential and existing sites. Part II of this report contains guidance on the design and implementation of a performance monitoring program for low-level radioactive waste disposal facilities. A monitoring programs is described that will assess whether engineered barriers surrounding the waste are effectively isolating the waste and will continue to isolate the waste by remaining structurally stable. Monitoring techniques and instruments are discussed relative to their ability to measure (a) parameters directly related to water movement though engineered barriers, (b) parameters directly related to the structural stability of engineered barriers, and (c) parameters that characterize external or internal conditions that may cause physical changes leading to enhanced water movement or compromises in stability. Data interpretation leading to decisions concerning facility closure is discussed. 120 refs., 12 figs., 17 tabs

Low-level radioactive waste disposal facility closure

Energy Technology Data Exchange (ETDEWEB)

White, G.J.; Ferns, T.W.; Otis, M.D.; Marts, S.T.; DeHaan, M.S.; Schwaller, R.G.; White, G.J. (EG and G Idaho, Inc., Idaho Falls, ID (USA))

1990-11-01

Part I of this report describes and evaluates potential impacts associated with changes in environmental conditions on a low-level radioactive waste disposal site over a long period of time. Ecological processes are discussed and baselines are established consistent with their potential for causing a significant impact to low-level radioactive waste facility. A variety of factors that might disrupt or act on long-term predictions are evaluated including biological, chemical, and physical phenomena of both natural and anthropogenic origin. These factors are then applied to six existing, yet very different, low-level radioactive waste sites. A summary and recommendations for future site characterization and monitoring activities is given for application to potential and existing sites. Part II of this report contains guidance on the design and implementation of a performance monitoring program for low-level radioactive waste disposal facilities. A monitoring programs is described that will assess whether engineered barriers surrounding the waste are effectively isolating the waste and will continue to isolate the waste by remaining structurally stable. Monitoring techniques and instruments are discussed relative to their ability to measure (a) parameters directly related to water movement though engineered barriers, (b) parameters directly related to the structural stability of engineered barriers, and (c) parameters that characterize external or internal conditions that may cause physical changes leading to enhanced water movement or compromises in stability. Data interpretation leading to decisions concerning facility closure is discussed. 120 refs., 12 figs., 17 tabs.

Mesoscale modelling of radioactive contamination formation in Ukraine caused by the Chernobyl accident

International Nuclear Information System (INIS)

Talerko, Nikolai

2005-01-01

This work is devoted to the reconstruction of time-dependent radioactive contamination fields in the territory of Ukraine in the initial period of the Chernobyl accident using the model of atmospheric transport LEDI (Lagrangian-Eulerian DIffusion model). The modelling results were compared with available 137 Cs air and ground contamination measurement data. The 137 Cs atmospheric transport over the territory of Ukraine was simulated during the first 12 days after the accident (from 26 April to 7 May 1986) using real aerological information and rain measurement network data. The detailed scenario of the release from the accidental unit of the Chernobyl nuclear plant has been built (including time-dependent radioactivity release intensity and time-varied height of the release). The calculations have enabled to explain the main features of spatial and temporal variations of radioactive contamination fields over the territory of Ukraine on the regional scale, including the formation of the major large-scale spots of radioactive contamination caused by dry and wet deposition

Remediation of sites with dispersed radioactive contamination

International Nuclear Information System (INIS)

2004-01-01

To respond to the needs of Member States, the IAEA launched an environmental remediation project to deal with the problems of radioactive contamination worldwide. The IAEA environmental remediation project includes an IAEA Coordinated Research Project, as well as the participation of IAEA experts in concrete remediation projects when requested by individual Member States. The IAEA has prepared several documents dedicated to particular technical or conceptual areas, including documents on the characterization of contaminated sites, technical and non-technical factors relevant to the selection of a preferred remediation strategy and technique, overview of applicable techniques for environmental remediation,, options for the cleanup of contaminated groundwater and planning and management issues. In addition, a number of other IAEA publications dealing with related aspects have been compiled under different IAEA projects; these include TECDOCs on the remediation of uranium mill tailings, the decontamination of buildings and roads and the characterization of decommissioned sites. Detailed procedures for the planning and implementation of remedial measures have been developed over the past decade or so. A critical element is the characterization of the contamination and of the various environmental compartments in which it is found, in order to be able to evaluate the applicability of remediation techniques. The chemical or mineralogical form of the contaminant will critically influence the efficiency of the remediation technique chosen. Careful delineation of the contamination will ensure that only those areas or volumes of material that are actually contaminated are treated. This, in turn, reduces the amount of any secondary waste generated. The application of a remediation technique requires holistic studies examining the technical feasibility of the proposed measures, including analyses of their impact. Consequently, input from various scientific and engineering

Annual Report of Radioactive Waste Facilities Operation in 2013

Institute of Scientific and Technical Information of China (English)

DU; Hong-ming; GAO; Zhi-gang; LIU; Fu-guo

2013-01-01

301,a section of Department of Radiochemistry,which manages 15 facilities and undertakes the administrative tasks of radioactive waste,is the important guarantee of scientific research production and safety in CIAE.1 The safe operation of the radioactive waste management facilities In 2013,in order to ensure the operation safety,we formulated the inspection regulations,which included regular operation inspection,week safety inspection from the leaders of the section and

Prediction of radionuclide inventory for the low-and intermediated-level radioactive waste disposal facility the radioactive waste classification

International Nuclear Information System (INIS)

Jung, Kang Il; Jeong, Noh Gyeom; Moon, Young Pyo; Jeong, Mi Seon; Park, Jin Beak

2016-01-01

To meet nuclear regulatory requirements, more than 95% individual radionuclides in the low- and intermediate-level radioactive waste inventory have to be identified. In this study, the radionuclide inventory has been estimated by taking the long-term radioactive waste generation, the development plan of disposal facility, and the new radioactive waste classification into account. The state of radioactive waste cumulated from 2014 was analyzed for various radioactive sources and future prospects for predicting the long-term radioactive waste generation. The predicted radionuclide inventory results are expected to contribute to secure the development of waste disposal facility and to deploy the safety case for its long-term safety assessment

Radioactive contamination in the environs of the Hanford Works for the period October, November, December 1949

Energy Technology Data Exchange (ETDEWEB)

Paas, H.J.; Singlevich, W.

1950-03-02

This report summarizes the measurements made for radioactive contamination in the environs of the Hanford Works. The principal sources of the radioactivity originating as a result of operations at Hanford which affect the environment in this area are the two waste stacks in the separations area and the cooling water from the four pile areas. Measurements are also made on samples taken from the Hanford waste systems which are primarily confined within the project proper. Although monthly summaries of these data are reported in Health Instrument Divisions Environs reports, a somewhat more detailed discussion of these data is covered in the quarterly report. In this manner, a better evaluation of possible trends can be detected as a result of the increased number of measurements made available by combining the data for a three month period. The following areas are discussed: meteorology, radioactive contamination of vegetation, airborne contamination and air radiation levels, radioactive contamination in Hanford wastes, radioactive contamination in the Columbia and Yakima rivers; beta activity in rain and snow, and radioactive contamination in drinking water and test wells.

Remediation Of Radioactive Contaminated Soil in Oil Fields

International Nuclear Information System (INIS)

Taha, A.A.; Hassib, G.M.; Ibrahim, Z.A.

2011-01-01

Radioactive contamination by naturally occurring radioactive materials (NORM) in evaporation pond has been evaluated. At several onshore oil field locations, the produced water is discharged to form artificial lagoons or ponds. Subsequently, the released waters drain to the ground leaving radioactive deposits associated with the soil that eventually require remedial action in accordance with radiation protection principles. The present study aims to investigate the remediation of contaminated soil in some oil fields and in this concern, two scenarios were proposed. The first scenario is studying the feasibility of using soil washing technique (a physical-chemical separation process) for removing radium-226 from the contaminated soil samples collected from an evaporating pond. The size/activity distribution analyses were carried out. The data obtained showed that almost 68 % of the investigated soil was coarse sand (≥ 300 μm), 28 % was medium and fine sand (≤300 μm and (≥75 μm) and only small fraction of 4 % was silt and clay (≤75 μm). A series of mild acids such as HCl and mild NaCl/HCl (chloride washing) were used for washing the investigated soil fractions. The obtained data showed that the coarse fraction ≥ 300 μm can be re mediated below a regulatory level of 1Bq/g. and the radium from this coarse fraction could be easily removed by screening and chloride washing. For the remediation of (≤ 300 μm and (≥ 75 μm soil fractions, a series of mild chloride washing experiments also showed that the chloride base (NaCl/HCl) was found to be potentially useful. However, there was a difficulty in achieving a low radium value in the fine (≥ 75 μm size fractions using chloride washing. The second scenario is to get rid of all contaminated soil and store it in a concrete basin through the program of radiological protection of personnel and environment. Preliminary gamma survey of contaminated soil showed that the significant area of the investigated

Radioactive contamination level of vehicles resulted from transporting fine rare-earth minerals by rail

International Nuclear Information System (INIS)

Han Kaichun; Yu Boyong; Gao Shengwei

1997-01-01

This paper presents monitoring results of radioactive contamination level of steel open wagon surface resulted from transporting fine rare-earth minerals. Under promising transport conditions (the packaging consists of two layers of plastic bags and two layers of plastic net sacks, each package contains 50 kg of minerals, each vehicle carries 60 t), the surface radioactivity (total α and total β) of 16 vehicles on two lines from Baotou to Wujiachuan (924 km) and from Baotou to Sankeshu (2236 km) was measured before loading, after unloading and washing, using α and β surface contamination detector. The results showed that the radioactive contamination level of the vehicle surface after unloading appeared significantly different. The contamination level of vehicle bases was higher than that of both sides, long distance vehicles was higher than that of short distance vehicles. The radioactive contamination level of vehicles surface after washing was below the standard limits, these vehicles can be used for ordinary goods transport

Radiation exposure to skin following radioactive contamination

International Nuclear Information System (INIS)

Baumann, H.; Beyermann, M.; Kraus, W.

1989-01-01

In the case of skin contamination intensive decontamination measures should not be carried out until the potential radiation exposure to the basal cell layer of the epidermis was assessed. Dose equivalent rates from alpha-, beta- or photon-emitting contaminants were calculated with reference to the surface activity for different skin regions as a function of radiation energy on the condition that the skin was healthy and uninjured and the penetration of contaminants through the epidermis negligible. The results have been presented in the form of figures and tables. In the assessment of potential skin doses, both radioactive decay and practical experience as to the decrease in the level of surface contamination by natural desquamation of the stratum corneum were taken into account. 9 figs., 5 tabs., 46 refs. (author)

The role of bioindicators in assessing radioactive contamination

International Nuclear Information System (INIS)

Marovicj, G.

1990-01-01

The paper is a survey of investigations into radioactive contamination of selected plant and animal species (bioindicators) which have the capacitr for multiple accumulation of fission products. Literature data on the contamination of bioindicators are compared with special reference to the accumulation of 131 I, 137 Cs and 90 Sr as a result of atmospheric nuclear experiments and the nuclear accident at Chernobyl. (author) 52 refs.; 3 figs [sh

Latest movements associated with radioactive contamination and disaster waste management (2)

International Nuclear Information System (INIS)

Omura, Tomomi

2012-01-01

As for the radioactive contamination countermeasures and disaster waste countermeasures taken for the accidents of the Great East Japan Earthquake and the Fukushima Daiichi Nuclear Station of Tokyo Electric Power Company, this paper introduces in the digest version the following movements from mid-April to May 15, 2012. (1) Radioactive substance countermeasures such as decontamination. (a) Decontamination operations under direct control of the Ministry of the Environment, (b) Establishment of compensation benchmarks by the Ministry of the Environment for the garden plants and land use in Special Decontamination Area, (c) Publication of technical guidelines by the Ministry of Agriculture, Forestry and Fisheries, on the removal and diffusion suppression of radioactive substances in forests, (d) Announcement of research center development / promotion idea by the government in the policy making for Fukushima reconstruction, (e) Request of the government for the interim storage facility site in the opinion exchange meetings in Futaba district towns and villages in Fukushima Prefecture, (f) Announcement of radioactive substance forecast map in Fukushima City for the first time by the government, and (g) Action plan development at the Health Anxiety Countermeasure Coordination Council for nuclear victims. (2) Disaster waste countermeasures. (a) Introduction of challenges in each of Miyagi Prefecture and Iwate Prefecture on the acceleration of the secondary temporary storage field development for disaster waste treatment, and (b) Introduction of progress in new interim incinerator construction plan for disaster waste treatment in Fukushima Prefecture. (O.A.)

International measures needed to protect metal recycling facilities from radioactive materials

International Nuclear Information System (INIS)

Mattia, M.; Wiener, R.

1999-01-01

In almost every major city and region of every country, there is a recycling facility that is designed to process or consume scrap metal. These same countries will probably have widespread applications of radioactive materials and radiation generating equipment. This material and equipment will have metal as a primary component of its housing or instrumentation. It is this metal that will cause these sources of radioactivity, when lost, stolen or mishandled, to be taken to a metal recycling facility to be sold for the value of the metal. This is the problem that has faced scrap recycling facilities for many years. The recycling industry has spent millions of dollars for installation of radiation monitors and training in identification of radioactive material. It has expended millions more for the disposal of radioactive material that has mistakenly entered these facilities. Action must be taken to prevent this material from entering the conventional recycling process. There are more than 2,300 known incidents of radioactive material found in recycled metal scrap. Worldwide, more than 50 smeltings of radioactive sources have been confirmed. Seven fatal accidents involving uncontrolled radioactive material have also been documented. Hazardous exposures to radioactive material have plagued not just the workers at metal recycling facilities. The families of these workers, including their children, have been exposed to potentially harmful levels of radioactivity. The threat from this material does not stop there. Radioactive material that is not caught at recycling facilities can be melted and the radioactivity has been found in construction materials used to build homes, as well as shovels, fencing material, and furniture offered for sale to the general public. The time has come for the international community to address the issue of the uncontrolled sources of radioactive material. The following are the key points that must be addressed. (i) Identification of sources

Processing method for contaminated water containing radioactive waste

International Nuclear Information System (INIS)

Tahara, Toshiaki; Fukagawa, Ken-ichiro.

1994-01-01

For absorbing contaminated water containing radioactive substances, a sheet is prepared by covering water absorbing pulps carrying an organic water absorbent having an excellent water absorbability is semi-solidified upon absorption water with a water permeable cloth, such as a non-woven fabric having a shape stability. As the organic water absorbent, a hydrophilic polymer which retains adsorbed water as it is used. In particular, a starch-grafted copolymer having an excellent water absorbability also for reactor water containing boric acid is preferred. The organic water absorbent can be carried on the water absorbing pulps by scattering a granular organic water absorbent to the entire surface of the water absorbing cotton pulp extended thinly to carry it uniformly and putting them between thin absorbing paper sheets. If contaminated water containing radioactive materials are wiped off by using such a sheet, the entire sheet is semi-solidified along with the absorption with no leaching of the contaminated water, thereby enabling to move the wastes to a furnace for applying combustion treatment. (T.M.)

NSC confirms principles for safety review on Radioactive Waste Burial Facilities

International Nuclear Information System (INIS)

Anon.

1988-01-01

The Nuclear Safety Commission authorized the scope of Principles for Safety Examination on Radioactive Waste Burial Facilities as suitable, the draft report for which was established by the Special Committee on Safety Standards of Radioactive Waste (Chairman Prof. Masao Sago, Science University of Tokyo) and reported on March 10 to the NSC. The principles include the theory that the facility must be controlled step by step, corresponding to the amount of radioactivity over 300 to 400 years after the burial of low-level solid radioactive waste with site conditions safe even in the event of occurrence of a natural disaster. The principles will be used for administrative safety examination against the application of the business on low-level radioactive waste burial facility which Japan Nuclear Fuel Industries, Inc. is planning to install at Rokkashomura, Aomori Prefecture. (author)

A Study on the Method to Discriminate Between the Internal and External Radioactive Contamination Using Whole Body Counter

International Nuclear Information System (INIS)

Kong, T. Y.; Kim, H. G.; Yang, H. Y.; Kang, D. W.; Lim, S. N.; Kim, H. J.; Jin, H. H.; Lee, S. G.; Park, S. C.

2006-01-01

Whole Body Counter (WBC) is used to identify and measure the radioactivity in the body of human beings in a nuclear power plants (NPPs). In domestic NPPs, it is prescribed that all workers should take a whole body counting after radiation works if the possibilities of radioactive contamination exist or the radioactivity is detected by a portal monitoring. It is, however, found that the external skin contamination is occasionally estimated as the internal radioactive contamination. In this case, the worker assumed to be detected is recommended to take showers for the decontamination of skin and take a whole body counting again. Although the detected radioactivity is reduced remarkably after several decontaminations, confirmed as the external skin contamination, it is determined finally as an internal exposure if the radioactivity is still detected in the body of worker. The amount of detected radioactivity can be much higher than that of the expected for this mistaken contamination since the radioisotopes attached to skin come to be close to the detectors of WBC. Finally, this makes the misjudgment of the external skin contamination as well as the excessively conservative estimation of radioactive contamination. In this study, several experiments were carried out to discriminate between the internal and external radioactive contamination using the humanoid phantom and WBC. Preliminary experimental results indicated that the use of front and backside counts could be applied to the discrimination of the external skin contamination and the difference of detected radioactivities between front and backside counts was less than about factor 2 for the internal contamination

Development of the Discrimination Programs between the Internal and External Radioactive Contamination of Workers Using a Whole Body Counter

International Nuclear Information System (INIS)

Kong, T. Y.; Kim, H. G.; Lim, S. N.; Kim, H. J.; Jin, H. H.; Lee, S. G.; Park, S. C.

2006-01-01

A whole body counter (WBC) is used to identify and measure the radioactivity in the body of human beings in a nuclear power plant (NPP). In domestic NPPs, several whole body counters are in operation to monitor the internal radioactive contamination of workers. All workers take a whole body counting after radiation works if there is high possibility of radioactive contamination or the radioactivity is detected by portal monitoring. It is, however, found that the external contamination is occasionally estimated as the internal radioactive contamination. In this case, the worker is recommended to take showers for the decontamination of skin and take a whole body counting again. Although the detected radioactivity is reduced remarkably after several decontaminations, confirmed as the external contamination, it is determined finally as an internal contamination if the radioactivity is still detected in the body of worker. The amount of detected radioactivity can be much higher than that of the expected for this mistaken contamination since the radioisotopes attached to skin come to be close to the detectors of WBC. Finally, this makes not only the misjudgment of the external contamination as the internal contamination, but also the excessively conservative estimation of radioactive contamination. In this study, several experiments were carried out to set up the discrimination program between the internal and external radioactive contamination using the humanoid phantom and a whole body counter. After the analysis of experimental results, we found that the use of front and backside counts could be applied to the discrimination of the external contamination and the ratio of detected radioactivities between front and backside counts was more than about factor 2 for the external contamination

Dry decontamination technology development for high radioactive contaminant application - Development of residual radiation assessment methodology for high radioactive facility decontamination

Energy Technology Data Exchange (ETDEWEB)

Lee, G. J.; Hong, D. S.; Jeong, H. Y. [Korea Advanced Institute of Science and Technology, Taejon (Korea)

2000-04-01

Humidity around the concrete structure can make the moisture distribution within the concrete. Moisture content of the structure will change due to the diffusion process with time. Radioactive material on the surface of concrete will eventually diffuse into the porous concrete and contaminates the internal region of the concrete. In this study, we have assumed two different diffusion processes depending on the different moisture content. One is for slow diffusion process near the surface and the other is for fast diffusion process in deep region. We have developed the mathematical diffusion model for the two different diffusion regions and the corresponding analytic solutions for the two regions are obtained. 19 refs., 15 figs., 9 tabs. (Author)

Residual radioactive contamination from decommissioning: Technical basis for translating contamination levels to annual dose

International Nuclear Information System (INIS)

Kennedy, W.E. Jr.; Peloquin, R.A.

1990-01-01

This document describes the generic modeling of the total effective dose equivalent (TEDE) to an individual in a population from a unit concentration of residual radioactive contamination. Radioactive contamination inside buildings and soil contamination are considered. Unit concentration TEDE factors by radionuclide, exposure pathway, and exposure scenario are calculated. Reference radiation exposure scenarios are used to derive unit concentration TEDE factors for about 200 individual radionuclides and parent-daughter mixtures. For buildings, these unit concentration factors list the annual TEDE for volume and surface contamination situations. For soil, annual TEDE factors are presented for unit concentrations of radionuclides in soil during residential use of contaminated land and the TEDE per unit total inventory for potential use of drinking water from a ground-water source. Because of the generic treatment of potentially complex ground-water systems, the annual TEDE factors for drinking water for a given inventory may only indicate when additional site data or modeling sophistication are warranted. Descriptions are provided of the models, exposure pathways, exposure scenarios, parameter values, and assumptions used. An analysis of the potential annual TEDE resulting from reference mixtures of residual radionuclides is provided to demonstrate application of the TEDE factors. 62 refs., 5 figs., 66 tabs

Vadose zone characterization of highly radioactive contaminated soil at the Hanford Site

International Nuclear Information System (INIS)

Buckmaster, M.A.

1993-05-01

The Hanford Site in south-central Washington State contains over 1500 identified waste sites and numerous groundwater plumes that will be characterized and remediated over the next 30 years. As a result of the Hanford Federal Facility Agreement and Consent Order, the US Department of Energy has initiated a remedial investigation/feasibility study at the 200-BP-1 operable unit. The 200-BP-1 remedial investigation is the first Comprehensive Environmental Response, Compensation, and Liability Act of 1980 investigation on the Hanford Site that involves drilling into highly radioactive and chemically contaminated soils. The initial phase of site characterization was designed to assess the nature and extent of contamination associated with the source waste site within the 200-BP-1 operable unit. Characterization activities consisted of drilling and sampling the waste site, chemical and physical analysis of samples, and development of a conceptual vadose zone model. Predicted modeling concentrations compared favorably to analytical data collected during the initial characterization activities

Radioactive contamination of aquatic media and organisms

International Nuclear Information System (INIS)

Fontaine, Y.

1960-01-01

After a brief account of the radioactive wastes produced by peaceful or military uses of Atomic Industry, the author first describes a series of observations carried out 'in the field' on the extent of contamination in aquatic organisms with respect to that of the medium. The experimental studies are then analysed, with reference both to the radioisotope metabolism and to the factors and types of contamination of aquatic organisms by wastes from atomic industry. A precise experimental project is presented at the end of the paper, including almost 300 references. (author) [fr

Environmental impact assessment for a radioactive waste facility: A case study

International Nuclear Information System (INIS)

Devgun, J.S.

1990-01-01

A 77-ha site, known as the Niagara Falls Storage Site and located in northwestern New York State, holds about 190, 000 m 3 of soils, wastes, and residues contaminated with radium and uranium. The facility is owned by the US Department of Energy. The storage of residues resulting from the processing of uranium ores started in 1944, and by 1950 residues from a number of plants were received at the site. The residues, with a volume of about 18,000 m 3 , account for the bulk of the radioactivity, which is primarily due to Ra-226; because of the extraction of uranium from the ore, the amount of uranium remaining in the residues is quite small. An analysis of the environmental impact assessment and environmental compliance actions taken to date at this site and their effectiveness are discussed. This case study provides an illustrative example of the complexity of technical and nontechnical issues for a large radiative waste facility. 11 refs., 7 figs., 2 tabs

Issues related to the licensing of final disposal facilities for radioactive waste

International Nuclear Information System (INIS)

Medici, M.A.; Alvarez, D.E.; Lee Gonzales, H.; Piumetti, E.H.; Palacios, E.

2010-01-01

The licensing process of a final disposal facility for radioactive waste involves the design, construction, pre-operation, operation, closure and post closure stages. While design and pre-operational stages are, to a reasonable extent, similar to other kind of nuclear or radioactive facilities, construction, operation, closure and post-closure of a radioactive waste disposal facility have unique meanings. As consequence of that, the licensing process should incorporate these particularities. Considering the long timeframes involved at each stage of a waste disposal facility, it is convenient that the development of the project being implemented in and step by step process, be flexible enough as to adapt to new requirements that would arise as a consequence of technology improvements or due to variations in the socio-economical and political conditions. In Argentina, the regulatory Standard AR 0.1.1 establishes the general guideline for the 'Licensing of Class I facilities (relevant facilities)'. Nevertheless, for radioactive waste final disposal facilities a new specific guidance should be developed in addition to the Basic Standard mentioned. This paper describes the particularities of final disposal facilities indicating that a specific licensing system for this type of facilities should be foreseen. (authors) [es

Soil magnetic susceptibility as indicator of radioactive contamination

International Nuclear Information System (INIS)

Curda, S.

2006-01-01

Measurement of magnetic susceptibility is a method, which is used in many areas of research. The locality Ak-Tjuz is typical example of old ecological load. One of the negative effects represents radioactive contamination. This situation is caused by environmental disaster in 1964. For useful reparation it is really necessary to determinate the surface range of contamination. And measurement of the magnetic susceptibility could be the suitable method for that kind of monitoring. (author)

Radioactive contamination of sewage sludge. Preliminary data

Energy Technology Data Exchange (ETDEWEB)

Soeder, C J; Zanders, E; Raphael, T

1986-01-01

Because of the radioactivity released through the explosion of the nuclear reactor near Chernobyl radionuclides have been accumulated to a significant extent in sewage sludge in the Federal Republic of Germany. This is demonstrated for samples from four activated sludge plants according to a recent recommendation of the German Commission for Radiation Protection, there is until now no reason to deviate from the common practices of sludge disposal or incineration. The degree of radioactive contamination of plant materials produced on farm lands on which sewage sludge is being spread cannot be estimated with sufficient certainty yet. Additional information is required.

Development of a Commonwealth Radioactive Waste Management Facility in Australia

International Nuclear Information System (INIS)

Hesterman, R.

2006-01-01

Full text: The Australian Government has commenced a process to build a Commonwealth Radioactive Waste Management Facility in the Northern Territory for management of radioactive wastes produced by Australian Government agencies. The Government is committed to safely managing its relatively small volume of low level radioactive waste (approximately 3800 cubic metres) and even smaller volume of intermediate level waste (around 400 cubic metres) that have been generated since the early 1950s from the research, medical and industrial use of radioactive materials. Australia has no high level radioactive waste as it does not have any nuclear power reactors. Australian states and territories are responsible for the safe and secure management of low level and intermediate level waste generated within their jurisdictions. They have jointly generated approximately 200 cubic metres of low level radioactive waste and under 100 cubic metres of intermediate level for the same period. In July 2004, the Prime Minister announced that the Australian Government would examine the suitability of Commonwealth land holdings, both onshore and offshore, for establishing the Facility. An initial assessment of offshore territories by the Department of Education, Science and Training (DEST) did not find any sufficiently suitable sites for hosting the Facility. This was due to the low elevation of most territories, inadequate infrastructure and incompatibility with existing land uses. In July 2005, Dr Nelson, then the Minister for Education, Science and Training, announced that three Department of Defence properties in the Northern Territory would be investigated for siting the Facility. The three properties are Fishers Ridge, about 43 kilometres southeast of Katherine; Harts Range, 100 kilometres directly northeast of Alice Springs; and Mt Everard, about 27 kilometres directly northwest of Alice Springs. In addition, the Commonwealth Radioactive Waste Management Act 2005, enacted in December

Process for affixing radioactive contamination on contaminated materials or wastes. Its application

International Nuclear Information System (INIS)

Aubouin, Guy; Aude, Georges; Tassigny, Christian de.

1982-01-01

The invention concerns a process for affixing radioactive contamination on materials or waste matter in order to ensure that the materials are transferred in complete safety or to package them when their activity is low. Under this process at least one coat of a resin polymerizable at ambient temperature, for example an epoxy resin, a polyester resin, a vinyl resin or a mixture of thermohardening resin and thermoplastic resin, is sprayed on to the contaminated material part by means of an electrostatic gun [fr

Management of Radioactive Wastes

International Nuclear Information System (INIS)

Tchokosa, P.

2010-01-01

Management of Radioactive Wastes is to protect workers and the public from the radiological risk associated with radioactive waste for the present and future. It application of the principles to the management of waste generated in a radioisotope uses in the industry. Any material that contains or is contaminated with radionuclides at concentrations or radioactivity levels greater than ‘exempt quantities’ established by the competent regulatory authorities and for which no further use is foreseen or intended. Origin of the Radioactive Waste includes Uranium and Thorium mining and milling, nuclear fuel cycle operations, Operation of Nuclear power station, Decontamination and decommissioning of nuclear facilities and Institutional uses of isotopes. There are types of radioactive waste: Low-level Waste (LLW) and High-level Waste. The Management Options for Radioactive Waste Depends on Form, Activity, Concentration and half-lives of the radioactive waste, Storage and disposal methods will vary according to the following; the radionuclides present, and their concentration, and radio toxicity. The contamination results basically from: Contact between radioactive materials and any surface especially during handling. And it may occur in the solid, liquid or gas state. Decontamination is any process that will either reduce or completely remove the amount of radionuclides from a contaminated surface

Safe operation of existing radioactive waste management facilities at Dalat Nuclear Research Institute

International Nuclear Information System (INIS)

Pham Van Lam; Ong Van Ngoc; Nguyen Thi Nang

2000-01-01

The Dalat Nuclear Research Reactor was reconstructed from the former TRIGA MARK-II in 1982 and put into operation in March 1984. The combined technology for radioactive waste management was newly designed and put into operation in 1984. The system for radioactive waste management at the Dalat Nuclear Research Institute (DNRI) consists of radioactive liquid waste treatment station and disposal facilities. The treatment methods used for radioactive liquid waste are coagulation and precipitation, mechanical filtering and ion- exchange. Near-surface disposal of radioactive wastes is practiced at DNRI In the disposal facilities eight concrete pits are constructed for solidification and disposal of low level radioactive waste. Many types of waste generated in DNRI and in some Nuclear Medicine Departments in the South of Vietnam are stored in the disposal facilities. The solidification of sludge has been done by cementation. Hydraulic compactor has done volume reduction of compatible waste. This paper presents fifteen-years of safe operation of radioactive waste management facilities at DNRI. (author)

Outline of the radioactive waste management strategy at the national radioactive waste disposal facility 'Ekores'

International Nuclear Information System (INIS)

Rozdyalovskaya, L.F.; Tukhto, A.A.; Ivanov, V.B.

2000-01-01

The national Belarus radioactive waste disposal facility 'Ekores' was started in 1964 and was designed for radioactive waste coming from nuclear applications in industry, medicine and research. It is located in the neighbourhood of Minsk (2 Mil. people) and it is the only one in this country. In 1997 the Government initiated the project for the facility reconstruction. The main reconstruction goal is to upgrade radiological safety of the site by creating adequate safety conditions for managing radioactive waste at the Ekores disposal facility. This covers modernising technologies for new coming wastes and also that the wastes currently disposed in the pits are retrieved, sorted and treated in the same way as new coming wastes. The reconstruction project developed by Belarus specialists was reviewed by the IAEA experts. The main provisions of the revised project strategy are given in this paper. The paper's intention is to outline the technical measures which may be taken at standard 'old type Soviet Radon' disposal facility so as to ensure the radiological safety of the site. (author)

Current Measures on Radioactive Contamination in Japan: A Policy Situation Analysis.

Science.gov (United States)

Gilmour, Stuart; Miyagawa, Shoji; Kasuga, Fumiko; Shibuya, Kenji

2016-01-01

The Great East Japan Earthquake on 11th March 2011 and the subsequent Fukushima Dai-ichi nuclear power plant disaster caused radioactive contamination in the surrounding environment. In the immediate aftermath of the accident the Government of Japan placed strict measures on radio-contamination of food, and enhanced radio-contamination monitoring activities. Japan is a pilot country in the WHO Foodborne Disease Burden Epidemiology Reference Group (FERG), and through this initiative has an opportunity to report on policy affecting chemicals and toxins in the food distribution network. Nuclear accidents are extremely rare, and a policy situation analysis of the Japanese government's response to the Fukushima Dai-ichi nuclear accident is a responsibility of Japanese scientists. This study aims to assess Japan government policies to reduce radio-contamination risk and to identify strategies to strengthen food policies to ensure the best possible response to possible future radiation accidents. We conducted a hand search of all publicly available policy documents issued by the Cabinet Office, the Food Safety Commission, the Ministry of Health, Labor and Welfare (MHLW), the Ministry of Agriculture, Forestry and Fishery (MAFF) and prefectural governments concerning food safety standards and changes to radiation and contamination standards since March 11th, 2011. We extracted information on food shipment and sales restrictions, allowable radio-contamination limits, monitoring activities and monitoring results. The standard for allowable radioactive cesium (Cs-134 and Cs-137) of 100 Bq/Kg in general food, 50 Bq/Kg in infant formula and all milk products, and 10 Bq/Kg in drinking water was enforced from April 2012 under the Food Sanitation Law, although a provisional standard on radio-contamination had been applied since the nuclear accident. Restrictions on the commercial sale and distribution of specific meat, vegetable and fish products were released for areas at risk of

Decommissioning of a Radioactive Facility Used for Biomolecule Labeling and Biological Effects

International Nuclear Information System (INIS)

Yagüe, L.; Navarro, N.; Álvarez, A.; Quiñones, J.

2015-01-01

This paper presents the measurement methodology designed for the final status survey of an old radioactive facility, used as radiolabeling lab. Its declassification as radioactive facility required the radiological characterization of all walls, structures and materials at the facility in order to reuse its outbuilding for conventional use. To demonstrate compliance with the declassification criteria, the design of the final status survey was performed applying MARSSIM(1) (Multi-Agency Radiation Survey and Site Investigation Manual) methodology and using different measurement techniques depending on the radioactive isotopes in the inventory of the facility, their half-lives and emission characteristics.

Illustrative assessment of human health issues arising from the potential release of chemotoxic substances from a generic geological disposal facility for radioactive waste.

Science.gov (United States)

Wilson, James C; Thorne, Michael C; Towler, George; Norris, Simon

2011-12-01

Many countries have a programme for developing an underground geological disposal facility for radioactive waste. A case study is provided herein on the illustrative assessment of human health issues arising from the potential release of chemotoxic and radioactive substances from a generic geological disposal facility (GDF) for radioactive waste. The illustrative assessment uses a source-pathway-receptor methodology and considers a number of human exposure pathways. Estimated exposures are compared with authoritative toxicological assessment criteria. The possibility of additive and synergistic effects resulting from exposures to mixtures of chemical contaminants or a combination of radiotoxic and chemotoxic substances is considered. The case study provides an illustration of how to assess human health issues arising from chemotoxic species released from a GDF for radioactive waste and highlights potential difficulties associated with a lack of data being available with which to assess synergistic effects. It also highlights how such difficulties can be addressed.

Illustrative assessment of human health issues arising from the potential release of chemotoxic substances from a generic geological disposal facility for radioactive waste

International Nuclear Information System (INIS)

Wilson, James C; Towler, George; Thorne, Michael C; Norris, Simon

2011-01-01

Many countries have a programme for developing an underground geological disposal facility for radioactive waste. A case study is provided herein on the illustrative assessment of human health issues arising from the potential release of chemotoxic and radioactive substances from a generic geological disposal facility (GDF) for radioactive waste. The illustrative assessment uses a source–pathway–receptor methodology and considers a number of human exposure pathways. Estimated exposures are compared with authoritative toxicological assessment criteria. The possibility of additive and synergistic effects resulting from exposures to mixtures of chemical contaminants or a combination of radiotoxic and chemotoxic substances is considered. The case study provides an illustration of how to assess human health issues arising from chemotoxic species released from a GDF for radioactive waste and highlights potential difficulties associated with a lack of data being available with which to assess synergistic effects. It also highlights how such difficulties can be addressed.

Auxiliary analyses in support of performance assessment of a hypothetical low-level waste facility: Two-phase flow and contaminant transport in unsaturated soils with application to low-level radioactive waste disposal. Volume 2

International Nuclear Information System (INIS)

Binning, P.; Celia, M.A.; Johnson, J.C.

1995-05-01

A numerical model of multiphase air-water flow and contaminant transport in the unsaturated zone is presented. The multiphase flow equations are solved using the two-pressure, mixed form of the equations with a modified Picard linearization of the equations and a finite element spatial approximation. A volatile contaminant is assumed to be transported in either phase, or in both phases simultaneously. The contaminant partitions between phases with an equilibrium distribution given by Henry's Law or via kinetic mass transfer. The transport equations are solved using a Galerkin finite element method with reduced integration to lump the resultant matrices. The numerical model is applied to published experimental studies to examine the behavior of the air phase and associated contaminant movement under water infiltration. The model is also used to evaluate a hypothetical design for a low-level radioactive waste disposal facility. The model has been developed in both one and two dimensions; documentation and computer codes are available for the one-dimensional flow and transport model

Defense waste processing facility radioactive operations. Part 1 - operating experience

International Nuclear Information System (INIS)

Little, D.B.; Gee, J.T.; Barnes, W.M.

1997-01-01

The Savannah River Site's Defense Waste Processing Facility (DWPF) near Aiken, SC is the nation's first and the world's largest vitrification facility. Following a ten year construction program and a 3 year non-radioactive test program, DWPF began radioactive operations in March 1996. This paper presents the results of the first 9 months of radioactive operations. Topics include: operations of the remote processing equipment reliability, and decontamination facilities for the remote processing equipment. Key equipment discussed includes process pumps, telerobotic manipulators, infrared camera, Holledge trademark level gauges and in-cell (remote) cranes. Information is presented regarding equipment at the conclusion of the DWPF test program it also discussed, with special emphasis on agitator blades and cooling/heating coil wear. 3 refs., 4 figs

Treatment of Gravel Contaminated with Naturally Occurring Radioactive Element

International Nuclear Information System (INIS)

Sohsah, M. A.; Kamal, S. M.; Mamoon, A.

2004-01-01

Environmental protection primarily means controlling the releases of radioactive and non-radioactive wastes to the environment and involves treatment, storage, cleanup and disposal of these wastes. The present study concerns the cleanup of gravel that has been contaminated with 2 26 R a. Aqueous solutions of different compositions including water and various concentrations of calcium chloride and barium chloride were used to leach the contaminated gravel. The leaching experiments were carried out in glass column. In some leaching experiments, samples of sandy soil were placed below the gravel to test the sorption of the leached 2 26 R a by the soil. The relative efficiencies of the leachant and the extent of sorption of the leached radionuclide were determined both by the liquid scintillation counting and by the thermoluminescent chips. The TLD chips record the dose before and after decontamination of the gravel and before and after contamination of the soil samples when used. The results obtained indicated that acidified barium chloride was relatively the most effective leachant of 2 26 R a contamination. It reduced the dose from the contaminated gravel to almost half. The soil sample used adsorbs the leached radionuclides efficiently, increasing the soil naturally low dose to about six folds

Understanding Contamination; Twenty Years of Simulating Radiological Contamination

Energy Technology Data Exchange (ETDEWEB)

Emily Snyder; John Drake; Ryan James

2012-02-01

A wide variety of simulated contamination methods have been developed by researchers to reproducibly test radiological decontamination methods. Some twenty years ago a method of non-radioactive contamination simulation was proposed at the Idaho National Laboratory (INL) that mimicked the character of radioactive cesium and zirconium contamination on stainless steel. It involved baking the contamination into the surface of the stainless steel in order to 'fix' it into a tenacious, tightly bound oxide layer. This type of contamination was particularly applicable to nuclear processing facilities (and nuclear reactors) where oxide growth and exchange of radioactive materials within the oxide layer became the predominant model for material/contaminant interaction. Additional simulation methods and their empirically derived basis (from a nuclear fuel reprocessing facility) are discussed. In the last ten years the INL, working with the Defense Advanced Research Projects Agency (DARPA) and the National Homeland Security Research Center (NHSRC), has continued to develop contamination simulation methodologies. The most notable of these newer methodologies was developed to compare the efficacy of different decontamination technologies against radiological dispersal device (RDD, 'dirty bomb') type of contamination. There are many different scenarios for how RDD contamination may be spread, but the most commonly used one at the INL involves the dispersal of an aqueous solution containing radioactive Cs-137. This method was chosen during the DARPA projects and has continued through the NHSRC series of decontamination trials and also gives a tenacious 'fixed' contamination. Much has been learned about the interaction of cesium contamination with building materials, particularly concrete, throughout these tests. The effects of porosity, cation-exchange capacity of the material and the amount of dirt and debris on the surface are very important factors

Resource book: Decommissioning of contaminated facilities at Hanford

International Nuclear Information System (INIS)

1991-09-01

In 1942 Hanford was commissioned as a site for the production of weapons-grade plutonium. The years since have seen the construction and operation of several generations of plutonium-producing reactors, plants for the chemical processing of irradiated fuel elements, plutonium and uranium processing and fabrication plants, and other facilities. There has also been a diversification of the Hanford site with the building of new laboratories, a fission product encapsulation plant, improved high-level waste management facilities, the Fast Flux test facility, commercial power reactors and commercial solid waste disposal facilities. Obsolescence and changing requirements will result in the deactivation or retirement of buildings, waste storage tanks, waste burial grounds and liquid waste disposal sites which have become contaminated with varying levels of radionuclides. This manual was established as a written repository of information pertinent to decommissioning planning and operations at Hanford. The Resource Book contains, in several volumes, descriptive information of the Hanford Site and general discussions of several classes of contaminated facilities found at Hanford. Supplementing these discussions are appendices containing data sheets on individual contaminated facilities and sites at Hanford. Twelve appendices are provided, corresponding to the twelve classes into which the contaminated facilities at Hanford have been organized. Within each appendix are individual data sheets containing administrative, geographical, physical, radiological, functional and decommissioning information on each facility within the class. 68 refs., 54 figs., 18 tabs

Resource book: Decommissioning of contaminated facilities at Hanford

International Nuclear Information System (INIS)

1991-09-01

In 1942 Hanford was commissioned as a site for the production of weapons-grade plutonium. The years since have seen the construction and operation of several generations of plutonium-producing reactors, plants for the chemical processing of irradiated fuel elements, plutonium and uranium processing and fabrication plants, and other facilities. There has also been a diversification of the Hanford site with the building of new laboratories, a fission product encapsulation plant, improved high-level waste management facilities, the Fast Flux test facility, commercial power reactors and commercial solid waste disposal facilities. Obsolescence and changing requirements will result in the deactivation or retirement of buildings, waste storage tanks, waste burial grounds and liquid waste disposal sites which have become contaminated with varying levels of radionuclides. This manual was established as a written repository of information pertinent to decommissioning planning and operations at Hanford. The Resource Book contains, in several volumes, descriptive information of the Hanford Site and general discussions of several classes of contaminated facilities found at Hanford. Supplementing these discussions are appendices containing data sheets on individual contaminated facilities and sites at Hanford. Twelve appendices are provided, corresponding to the twelve classes into which the contaminated facilities at Hanford have been organized. Within each appendix are individual data sheets containing administrative, geographical, physical, radiological, functional and decommissioning information on each facility within the class. 49 refs., 44 figs., 14 tabs

A prospect of the administration against problems of environmental contamination caused by radioactive nuclides

International Nuclear Information System (INIS)

Osako, Masahiro

2012-01-01

At first, focusing on the problem of radioactive contaminated wastes caused by Fukushima Daiichi Nuclear Accident, the Author described an outline of the waste management policy based on the law on special measures against the environmental contamination by radioactive nuclides. Next, the Author discussed a prospect of the environmental administration against the radioactive contamination problem. The most important mission of the environmental administration for the future must be to establish a social basis for the sustainable development, in other words the building-up of a newly social value added, through the measures against this unprecedented disaster. (author)

Radioactive wastes. Safety of storage facilities

International Nuclear Information System (INIS)

Devillers, Ch.

2001-01-01

A radioactive waste storage facility is designed in a way that ensures the isolation of wastes with respect to the biosphere. This function comprises the damping of the gamma and neutron radiations from the wastes, and the confinement of the radionuclides content of the wastes. The safety approach is based on two time scales: the safety of the insulation system during the main phase of radioactive decay, and the assessment of the radiological risks following this phase. The safety of a surface storage facility is based on a three-barrier concept (container, storage structures, site). The confidence in the safety of the facility is based on the quality assurance of the barriers and on their surveillance and maintenance. The safety of a deep repository will be based on the site quality, on the design and construction of structures and on the quality of the safety demonstration. This article deals with the safety approach and principles of storage facilities: 1 - recall of the different types of storage facilities; 2 - different phases of the life of a storage facility and regulatory steps; 3 - safety and radiation protection goals (time scales, radiation protection goals); 4 - safety approach and principles of storage facilities: safety of the isolation system (confinement system, safety analysis, scenarios, radiological consequences, safety principles), assessment of the radiation risks after the main phase of decay; 5 - safety of surface storage facilities: safety analysis of the confinement system of the Aube plant (barriers, scenarios, modeling, efficiency), evaluation of radiological risks after the main phase of decay; experience feedback of the Manche plant; variants of surface storage facilities in France and abroad (very low activity wastes, mine wastes, short living wastes with low and average activity); 6 - safety of deep geological disposal facilities: legal framework of the French research; international context; safety analysis of the confinement system

Control of radioactive contamination of food in the country Somogy

International Nuclear Information System (INIS)

Varga, E.; Viragh, I.

1980-01-01

The radioactive contamination of spinach, sorrel, lettuce, animal bones, milk and fish was determined in the period 1961-1978. Peak values were measured in 1963 and 1976. The contamination of plants reached higher levels, however, it did not exceed 25 pCi per g dry weight. (L.E.)

Improvements of present radioactive beam facilities and new projects

International Nuclear Information System (INIS)

Mueller, A.C.

1995-01-01

A short overview is given over scheduled improvements of present radioactive beam facilities and of new projects. In order to put these into a coherent context the paper starts with a general section about the making of radioactive beams. (author)

Radioactive ion beam facilities in Europe

International Nuclear Information System (INIS)

Blumenfeld, Y.

2008-01-01

The past two decades have seen extraordinarily rapid development of radioactive beam physics throughout the world and in particular in Europe. The important scientific advances have stemmed from a large number of facilities. Previously existing stable beam machines have been adapted to produce rare isotope beams and dedicated facilities have come on-line. This talk gives an overview of the present European installations highlighting their complementary nature. The European roadmap calls for the construction of two next generation facilities: FAIR making use of projectile fragmentation and EURISOL based on the ISOL technique. The future FAIR facility will be described and the path towards EURISOL presented in the light of the construction of 'intermediate' generation facilities SPIRAL2, HIE ISOLDE and SPES and results from the ongoing EURISOL Design Study.

Calculation of Radioactivity Concentration on Cover Depth of Contaminated Zone for Self-Disposal

Energy Technology Data Exchange (ETDEWEB)

Koo, Daeseo; Sung, Hyun-Hee; Kim, Gye-Nam; Kim, Seung-Soo; Kim, Ilgook; Han, Gyu Seong; Choi, Jong-Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

We have a lot of uranium contaminated soil and concrete wastes owing to dismantlement of uranium conversion facility. There are several radioactive material disposal methods such as regulation exemption, decontamination and long term storage. It is necessary for us to perform permanent disposal of these wastes. To acquire radiation dose under self-disposal from them, the study on decontamination of some uranium contaminated soil and concrete wastes was performed using electrokinectic-electrodialytic. In this study, we evaluated radiation dose on the cover depth of contaminated zone from the wastes under radiation dose limit using RESRAD Version 6.5. At first, the calculation of the radiation dose on the wastes of contaminated zone are carried out. The second, the cover depth of contaminated zone are analyzed. The application to self-disposal of contaminated zone are also analyzed. To acquire radiation dose under self-disposal from uranium contaminated soil and concrete wastes, we decontaminated some uranium contaminated soil and concrete wastes using electrokinectic-electrodialytic. To perform self-disposal of the quantity (30,000kg) of contaminated zone, the calculating conditions for radiation dose on the cover depth of contaminated zone are as follows. The area of contaminated zone is 10m{sup 2}. The thickness of contaminated zone is 2 m. The cover depth of contaminated zone are analyzed. The application to self-disposal of contaminated zone are also analyzed. Therefore, as the cover depth increases, the uranium concentration has an increasing trend. It realize that the cover depth of contaminated zone is adequate < 2m at the quantity(30,000kg) of contaminated zone. As the cover depth increases, the uranium concentration has a decreasing trend. As the cover depth increases, the radiation dose(residents) has also a decreasing trend.

Materials and Fuels Complex Facilities Radioactive Waste Management Basis and DOE Manual 435.1-1 Compliance Tables

Energy Technology Data Exchange (ETDEWEB)

Lisa Harvego; Brion Bennett

2011-09-01

Department of Energy Order 435.1, 'Radioactive Waste Management,' along with its associated manual and guidance, requires development and maintenance of a radioactive waste management basis for each radioactive waste management facility, operation, and activity. This document presents a radioactive waste management basis for Idaho National Laboratory's Materials and Fuels Complex facilities that manage radioactive waste. The radioactive waste management basis for a facility comprises existing laboratory-wide and facility-specific documents. Department of Energy Manual 435.1-1, 'Radioactive Waste Management Manual,' facility compliance tables also are presented for the facilities. The tables serve as a tool for developing the radioactive waste management basis.

Materials and Fuels Complex Facilities Radioactive Waste Management Basis and DOE Manual 435.1-1 Compliance Tables

International Nuclear Information System (INIS)

Harvego, Lisa; Bennett, Brion

2011-01-01

Department of Energy Order 435.1, 'Radioactive Waste Management,' along with its associated manual and guidance, requires development and maintenance of a radioactive waste management basis for each radioactive waste management facility, operation, and activity. This document presents a radioactive waste management basis for Idaho National Laboratory's Materials and Fuels Complex facilities that manage radioactive waste. The radioactive waste management basis for a facility comprises existing laboratory-wide and facility-specific documents. Department of Energy Manual 435.1-1, 'Radioactive Waste Management Manual,' facility compliance tables also are presented for the facilities. The tables serve as a tool for developing the radioactive waste management basis.

Radioactive contamination of aquatic media and organisms; La contamination radioactive des milieux et des organismes aquatiques

Energy Technology Data Exchange (ETDEWEB)

Fontaine, Y [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1960-07-01

After a brief account of the radioactive wastes produced by peaceful or military uses of Atomic Industry, the author first describes a series of observations carried out 'in the field' on the extent of contamination in aquatic organisms with respect to that of the medium. The experimental studies are then analysed, with reference both to the radioisotope metabolism and to the factors and types of contamination of aquatic organisms by wastes from atomic industry. A precise experimental project is presented at the end of the paper, including almost 300 references. (author) [French] Apres une courte etude des dechets radioactifs produits par les utilisations pacifiques ou militaires de l'Industrie Atomique, l'auteur fait etat d'abord des observations effectuees 'sur le terrain' concernant l'extension de la contamination des organismes aquatiques en rapport avec celle du milieu. L'auteur analyse ensuite les etudes experimentales se rapportant aussi bien au metabolisme des radioisotopes qu'aux facteurs et aux modalites de la contamination des organismes aquatiques par les dechets de l'industrie atomique. Un projet de travail experimental precis est presente a la fin de cette revue qui comporte pres de 300 references bibliographiques. (auteur)

Cleanup procedures at the Nevada Test Site and at other radioactively contaminated sites including representative costs of cleanup and treatment of contaminated areas

International Nuclear Information System (INIS)

Talmage, S.S.; Chilton, B.D.

1987-09-01

This review summarizes available information on cleanup procedures at the Nevada Test Site and at other radioactively contaminated sites. Radionuclide distribution and inventory, size of the contaminated areas, equipment, and cleanup procedures and results are included. Information about the cost of cleanup and treatment for contaminated land is presented. Selected measures that could be useful in estimating the costs of cleaning up radioactively contaminated areas are described. 76 refs., 16 tabs

Measures against radioactive contamination due to Fukushima First Nuclear Power Plant accidents. Part 3. Removing and decontamination of contaminated soil

International Nuclear Information System (INIS)

Ishii, K.; Terakawa, A.; Matsuyama, S.

2012-01-01

We studied the structure of radioactive cesium distribution in soil and found the exponential dependence. This behavior could be explained theoretically. We developed a useful method to decontaminate the soil contaminated with radioactive cesium atoms. We applied our method to the contaminated school yards of elementary schools of Marumori town and decontaminated total area of about 7000 m"2. (author)

Characterization of radioactively contaminated sites for remediation purposes

International Nuclear Information System (INIS)

1998-05-01

Characterization of the contaminated site is essential before embarking on a programme for its remediation and ultimate restoration. Reliable and suitable data must be obtained regarding the distribution and physical, chemical and nuclear properties of all radioactive contaminants. Characterization data is necessary for assessing the associated radiation risks and is used in support of the required engineering design and project planning for the environmental restoration. In addition, continuing characterization can provide information regarding efficiency of the cleanup methods and influence possible redirection of work efforts. Similarly, at the end of the remediation phase, characterization and ongoing monitoring can be used to demonstrate completion and success of the cleanup process. The suggested methodology represents a contribution attempting to solve the issue of preremediation characterization in a general manner. However, a number of difficulties might make this methodology unsuitable for general application across the diverse social, environmental and political systems in the IAEA Member States. This TECDOC covers the methodologies used to characterize radioactively contaminated sites for the purpose of remediating the potential sources of radiation exposure and assessing the hazards to human health and the environment

Socioeconomic issues and analyses for radioactive waste disposal facilities

International Nuclear Information System (INIS)

Ulland, L.

1988-01-01

Radioactive Waste facility siting and development can raise major social and economic issues in the host area. Initial site screening and analyses have been conducted for both potential high-level and low-level radioactive waste facilities; more detailed characterization and analyses are being planned. Results of these assessments are key to developing community plans that identify and implement measures to mitigate adverse socioeconomic impacts. Preliminary impact analyses conducted at high-level sites in Texas and Nevada, and site screening activities for low-level facilities in Illinois and California have identified a number of common socioeconomic issues and characteristics as well as issues and characteristics that differ between the sites and the type of facilities. Based on these comparisons, implications for selection of an appropriate methodology for impact assessment and elements of impact mitigation are identified

Occupational and Public Exposure During Normal Operation of Radioactive Waste Disposal Facilities

Directory of Open Access Journals (Sweden)

M. V. Vedernikova

2017-01-01

Full Text Available This paper focuses on occupational and public exposure during operation of disposal facilities receiving liquid and solid radioactive waste of various classes and provides a comparative analysis of the relevant doses: actual and calculated at the design stage. Occupational and public exposure study presented in this paper covers normal operations of a radioactive waste disposal facility receiving waste. Results: Analysis of individual and collective occupational doses was performed based on data collected during operation of near-surface disposal facilities for short-lived intermediate-, lowand very low-level waste in France, as well as nearsurface disposal facilities for long-lived waste in Russia. Further analysis of occupational and public doses calculated at the design stage was completed covering a near-surface disposal facility in Belgium and deep disposal facilities in the United Kingdom and the Nizhne-Kansk rock massive (Russia. The results show that engineering and technical solutions enable almost complete elimination of internal occupational exposure, whereas external exposure doses would fall within the range of values typical for a basic nuclear facility. Conclusion: radioactive waste disposal facilities being developed, constructed and operated meet the safety requirements effective in the Russian Federation and consistent with relevant international recommendations. It has been found that individual occupational exposure doses commensurate with those received by personnel of similar facilities abroad. Furthermore, according to the forecasts, mean individual doses for personnel during radioactive waste disposal would be an order of magnitude lower than the dose limit of 20 mSv/year. As for the public exposure, during normal operation, potential impact is virtually impossible by delaminating boundaries of a nuclear facility sanitary protection zone inside which the disposal facility is located and can be solely attributed to the use

Characterization of naturally occurring radioactive materials and Cobald-60 contaminated ferrous scraps from steel industries

International Nuclear Information System (INIS)

Chao, H.E.; Chiu, H.S.; Hunga, J.Y.; His, H.W.; Chen, Y.B.

2002-01-01

Since the occurrence of radioactively contaminated rebar incident in 1992, steel industries in Taiwan were encouraged by Atomic Energy Council (AEC) to install portal monitor to detect the abnormal radiation in shipments of metal scrap feed. From 1994 through 1999, there were 53 discoveries of radioactivity in ferrous scraps by steel companies. These include 15 orphan radioactive sources, 16 cobalt-60 contaminated rebars, 20 Naturally Occurring Radioactive Material (NORM) contaminated scraps, and two unknowns. Most NORM-contaminated scraps were from abroad. The NORM and cobalt-60 contaminated scraps were taken from the steel mills and analyzed in laboratory. The analytical results of scales and sludge sampled from NORM-contaminated scraps combining with the circumstantial evidences indicate that five possible industrial processes may be involved. They are oil production and treatment, heavy mineral sand benefication and rare earth processing, copper mining and processing, recovery of ammonium chloride by lime adsorption in Ammonium-soda process, and tailing of uranium enrichment process. The cobalt-60 activity and trace elements concentrations of contaminated rebars confirm that all of them were produced domestically in the period from Oct. 1982 to Jan. 1983, when the cobalt-60 sources were lost and entered the electric arc furnace to produce the contaminated rebars. (author)

Sources to environmental radioactive contamination from nuclear activities in the former USSR

International Nuclear Information System (INIS)

Polikarpov, G.G.; Aarkrog, A.

1993-01-01

There is three major sites of radioactive environmental contamination in the former USSR: the Cheliabinsk region in the Urals, Chernobyl NPP in Ukraine and Novaya Zemlya in the Arctic Ocean. The first mentioned is the most important with regard to local (potential) contamination, the last one dominates the global contamination. A number of sites and sources are less well known with regard to environmental contamination. This is thus the case for the plutonium production factories at Tomsk and Dodonovo. More information on nuclear reactors in lost or dumped submarines is also needed. From a global point of view reliable assessment of the radioactive run-off from land and deposits of nuclear waste in the Arctic Ocean are in particular pertinent

Biological cycles of radioactive contaminants

International Nuclear Information System (INIS)

Michon, M.-G.

1959-01-01

Artificial radio-elements (synthesized for scientific or industrial purposes)having been released, may be absorbed by plants or animals, and may eventually involve a catenation of organisms as some feed on the others. All organisms living in a polluted river become more radioactive than the water, which was to be expected, in as much as organisms are hypertonic in respect to sweet water. Conversely, soil brings into play physico-chemical phenomena (absorption) such that plants can get only a small portion of contaminating radio-elements, land animal feeding on such plants are relatively less exposed to contamination, and carnivorous animals feeding on herbivorous are still less exposed. Man, notably is fairly well protected, whereas lower organisms, notably unicellular organisms may suffer (mutations..). Reprint of a paper published in 'Revue de Pathologie Generale et de Physiologie Clinique', n. 707, April 1959, p. 505-514 [fr

Radioactive contamination from Chernobyl accident over Alexandria city

International Nuclear Information System (INIS)

Ammar, E.A.; El-Khatib, A.M.; Wahba, A.G.; Elraey, M.

1987-01-01

The concentration of radioactive contamination in air resulting from the Chernobyl accident has been followed up. A sudden and sharp increase was detected seven days after the start of the accident. This increase amounted to about 650 times the normal air-borne activity. (author)

Predisposal Management of Radioactive Waste from Nuclear Fuel Cycle Facilities. Specific Safety Guide

International Nuclear Information System (INIS)

2016-01-01

This Safety Guide provides guidance on the predisposal management of all types of radioactive waste (including spent nuclear fuel declared as waste and high level waste) generated at nuclear fuel cycle facilities. These waste management facilities may be located within larger facilities or may be separate, dedicated waste management facilities (including centralized waste management facilities). The Safety Guide covers all stages in the lifetime of these facilities, including their siting, design, construction, commissioning, operation, and shutdown and decommissioning. It covers all steps carried out in the management of radioactive waste following its generation up to (but not including) disposal, including its processing (pretreatment, treatment and conditioning). Radioactive waste generated both during normal operation and in accident conditions is considered

Development of portable and automatic smear sampler for measuring surface contamination

Energy Technology Data Exchange (ETDEWEB)

Lee, Bong Jae; Chang, S. Y.; Kim, B. H.; Kim, J. S.; Lee, H. S.; Kim, C. K.; Swol, C. W

2000-12-01

In measuring radioactive contamination in radiation controlled area of nuclear facility, the technical criteria to evaluate surface contamination level and to sample by indirect method was established in this paper. Radioactive materials always present on surface within operating nuclear facilities. Because of the presence of interfering radiation field, health physicists take smear samples to monitoring surface contamination according to routine monitoring program. But there are some problems like great errors and difference of personnel. Then, to solve them, The portable and automatic smear sampling apparatus was designed and fabricated.

Development of portable and automatic smear sampler for measuring surface contamination

International Nuclear Information System (INIS)

Lee, Bong Jae; Chang, S. Y.; Kim, B. H.; Kim, J. S.; Lee, H. S.; Kim, C. K.; Swol, C. W.

2000-12-01

In measuring radioactive contamination in radiation controlled area of nuclear facility, the technical criteria to evaluate surface contamination level and to sample by indirect method was established in this paper. Radioactive materials always present on surface within operating nuclear facilities. Because of the presence of interfering radiation field, health physicists take smear samples to monitoring surface contamination according to routine monitoring program. But there are some problems like great errors and difference of personnel. Then, to solve them, The portable and automatic smear sampling apparatus was designed and fabricated

Facilities for the examination of radioactive bodies

International Nuclear Information System (INIS)

Ginniff, M.E.; Richardson, E.K.

1981-01-01

A facility for the examination of radioactive bodies comprises carriages, each transporting one or more radioactive bodies, e.g. nuclear fuel elements, which travel along a shielded passage to bring the bodies to examination stations spaced along the passage. The passage comprises a circular section tube surrounded by a thick cylinder of shielding material e.g. lead. The transverse sectional dimensions of the passage are not much larger than the corresponding dimensions of the carriages in order to maintain the radioactive region as small as possible. Equipment for the examination of the radioactive bodies is located outside the shielded passage, and may be for metallurgical examination, e.g. by ultrasonics, radiography or other non-destructive testing means, or for mensuration to identify changes in shape, dimensions or weight. (author)

Technical evaluation of proposed Ukrainian Central Radioactive Waste Processing Facility

International Nuclear Information System (INIS)

Gates, R.; Glukhov, A.; Markowski, F.

1996-06-01

This technical report is a comprehensive evaluation of the proposal by the Ukrainian State Committee on Nuclear Power Utilization to create a central facility for radioactive waste (not spent fuel) processing. The central facility is intended to process liquid and solid radioactive wastes generated from all of the Ukrainian nuclear power plants and the waste generated as a result of Chernobyl 1, 2 and 3 decommissioning efforts. In addition, this report provides general information on the quantity and total activity of radioactive waste in the 30-km Zone and the Sarcophagus from the Chernobyl accident. Processing options are described that may ultimately be used in the long-term disposal of selected 30-km Zone and Sarcophagus wastes. A detailed report on the issues concerning the construction of a Ukrainian Central Radioactive Waste Processing Facility (CRWPF) from the Ukrainian Scientific Research and Design institute for Industrial Technology was obtained and incorporated into this report. This report outlines various processing options, their associated costs and construction schedules, which can be applied to solving the operating and decommissioning radioactive waste management problems in Ukraine. The costs and schedules are best estimates based upon the most current US industry practice and vendor information. This report focuses primarily on the handling and processing of what is defined in the US as low-level radioactive wastes

Classification and Reevaluation on Radionuclide and Activity of Contaminated Soil(I)

Energy Technology Data Exchange (ETDEWEB)

Kang, Il Sik; Shon, J. S.; Kim, K. J.; Kim, T. K.; Hong, D. S.; Lee, B. C.; Cho, H. S.; Je, W. G

2006-03-15

Radioactive wastes generated during the decommissioning process and contaminated soils were transported and have been stored at the waste storage facility. The radioactivity in the wastes has been decayed a lot. The radionuclide and the activity concentration of stored soil wastes were reevaluated. And using the reevaluation results, the soil wastes were classified as either a regulatory clearance wastes or a radioactive waste. The storage space can be secured by storing regulatory clearance wastes in the extra storage facility and self disposing them. Also, the objective is to protect the environment from contamination by observing the related nuclear regulation and managing the radioactive wastes. Through the reevaluation of radioactivity and classification of contaminated soils, the unnecessary decontamination of uncontaminated soil was prevented. It allowed us to save the cost for decontamination and disposal, also we could secure the pretreatment process techniques such as how to sample and analyze the nuclide.

Analysis of contamination conditions of the Joyo Waste Treatment Facility

International Nuclear Information System (INIS)

Yoshizawa, S.; Ishijima, N.; Tanimoto, K.

1999-08-01

Decontamination methods have been studied for decommissioning of Joyo Waste Treatment Facility whose operation has been stopped in 1994. In this study, we analyzed samples of its system piping, whose dose rate was relatively low, to determine conditions of contamination. We also study appropriate decontamination methods for them. Results are as follows. 1. The inner surfaces of piping were covered with a very thin clad that was less than 1 micrometer in thickness and had many vacancies, looked like particle detachment, which were about 20 micrometers in depth. Something like corrosion product was observed near the surface and it was 440 micrometers in depth. 2. Radioactive contamination was considered to settle on a lower part of the piping and to be buried in the clad. A kind of dominant contamination nuclide was 60 Co. 3. Hot nitric acid process will be suitable for system decontamination to reduce dose rate before dismantling. But its feasibility tests are indispensable using samples of main system components that have high dose rate. Rubber lining tanks requires another methods because of its difficulty of decontamination. 4. Analyses and decontamination tests using main system are required to decide through decontamination methods according to the clearance level. (author)

Analysis of local acceptance of a radioactive waste disposal facility.

Science.gov (United States)

Chung, Ji Bum; Kim, Hong-Kew; Rho, Sam Kew

2008-08-01

Like many other countries in the world, Korea has struggled to site a facility for radioactive waste for almost 30 years because of the strong opposition from local residents. Finally, in 2005, Gyeongju was established as the first Korean site for a radioactive waste facility. The objectives of this research are to verify Gyeongju citizens' average level of risk perception of a radioactive waste disposal facility as compared to other risks, and to explore the best model for predicting respondents' acceptance level using variables related to cost-benefit, risk perception, and political process. For this purpose, a survey is conducted among Gyeongju residents, the results of which are as follows. First, the local residents' risk perception of an accident in a radioactive waste disposal facility is ranked seventh among a total of 13 risks, which implies that nuclear-related risk is not perceived very highly by Gyeongju residents; however, its characteristics are still somewhat negative. Second, the comparative regression analyses show that the cost-benefit and political process models are more suitable for explaining the respondents' level of acceptance than the risk perception model. This may be the result of the current economic depression in Gyeongju, residents' familiarity with the nuclear industry, or cultural characteristics of risk tolerance.

Radioactive Liquid Waste Treatment Facility: Environmental Information Document

Energy Technology Data Exchange (ETDEWEB)

Haagenstad, H.T.; Gonzales, G.; Suazo, I.L. [Los Alamos National Lab., NM (United States)

1993-11-01

At Los Alamos National Laboratory (LANL), the treatment of radioactive liquid waste is an integral function of the LANL mission: to assure U.S. military deterrence capability through nuclear weapons technology. As part of this mission, LANL conducts nuclear materials research and development (R&D) activities. These activities generate radioactive liquid waste that must be handled in a manner to ensure protection of workers, the public, and the environment. Radioactive liquid waste currently generated at LANL is treated at the Radioactive Liquid Waste Treatment Facility (RLWTF), located at Technical Area (TA)-50. The RLWTF is 30 years old and nearing the end of its useful design life. The facility was designed at a time when environmental requirements, as well as more effective treatment technologies, were not inherent in engineering design criteria. The evolution of engineering design criteria has resulted in the older technology becoming less effective in treating radioactive liquid wastestreams in accordance with current National Pollutant Discharge Elimination System (NPDES) and Department of Energy (DOE) regulatory requirements. Therefore, to support ongoing R&D programs pertinent to its mission, LANL is in need of capabilities to efficiently treat radioactive liquid waste onsite or to transport the waste off site for treatment and/or disposal. The purpose of the EID is to provide the technical baseline information for subsequent preparation of an Environmental Impact Statement (EIS) for the RLWTF. This EID addresses the proposed action and alternatives for meeting the purpose and need for agency action.

Radioactive Liquid Waste Treatment Facility: Environmental Information Document

International Nuclear Information System (INIS)

Haagenstad, H.T.; Gonzales, G.; Suazo, I.L.

1993-11-01

At Los Alamos National Laboratory (LANL), the treatment of radioactive liquid waste is an integral function of the LANL mission: to assure U.S. military deterrence capability through nuclear weapons technology. As part of this mission, LANL conducts nuclear materials research and development (R ampersand D) activities. These activities generate radioactive liquid waste that must be handled in a manner to ensure protection of workers, the public, and the environment. Radioactive liquid waste currently generated at LANL is treated at the Radioactive Liquid Waste Treatment Facility (RLWTF), located at Technical Area (TA)-50. The RLWTF is 30 years old and nearing the end of its useful design life. The facility was designed at a time when environmental requirements, as well as more effective treatment technologies, were not inherent in engineering design criteria. The evolution of engineering design criteria has resulted in the older technology becoming less effective in treating radioactive liquid wastestreams in accordance with current National Pollutant Discharge Elimination System (NPDES) and Department of Energy (DOE) regulatory requirements. Therefore, to support ongoing R ampersand D programs pertinent to its mission, LANL is in need of capabilities to efficiently treat radioactive liquid waste onsite or to transport the waste off site for treatment and/or disposal. The purpose of the EID is to provide the technical baseline information for subsequent preparation of an Environmental Impact Statement (EIS) for the RLWTF. This EID addresses the proposed action and alternatives for meeting the purpose and need for agency action

303-K Radioactive Mixed-Waste Storage Facility closure plan

International Nuclear Information System (INIS)

1991-11-01

The Hanford Site, located northwest of Richland, Washington, houses reactors chemical-separation systems, and related facilities used for the production o special nuclear materials. The 300 Area of the Hanford Site contains reactor fuel manufacturing facilities and several research and development laboratories. The 303-K Radioactive Mixed-Waste Storage Facility (303-K Facility) has been used since 1943 to store various radioactive,and dangerous process materials and wastes generated by the fuel manufacturing processes in the 300 Area. The mixed wastes are stored in US Department of Transportation (DOT)-specification containers (DOT 1988). The north end of the building was used for storage of containers of liquid waste and the outside storage areas were used for containers of solid waste. Because only the north end of the building was used, this plan does not include the southern end of the building. This closure plan presents a description of the facility, the history of materials and wastes managed, and a description of the procedures that will be followed to chose the 303-K Facility as a greater than 90-day storage facility. The strategy for closure of the 303-K Facility is presented in Chapter 6.0

Overview of linac applications at future radioactive beam facilities

International Nuclear Information System (INIS)

Nolen, J.A.

1996-01-01

There is considerable interest worldwide in the research which could be done at a next generation, advanced radioactive beam facility. To generate high quality, intense beams of accelerated radionuclides via the open-quotes isotope separator on-lineclose quotes (ISOL) method requires two major accelerator components: a high power (100 kW) driver device to produce radionuclides in a production target/ion source complex, and a secondary beam accelerator to produce beams of radioactive ions up to energies on the order of 10 MeV per nucleon over a broad mass range. In reviewing the technological challenges of such a facility, several types of modem linear accelerators appear well suited. This paper reviews the properties of the linacs currently under construction and those proposed for future facilities for use either as the driver device or the radioactive beam post-accelerator. Other choices of accelerators, such as cyclotrons, for either the driver or secondary beam devices of a radioactive beam complex will also be compared. Issues to be addressed for the production accelerator include the choice of ion beam types to be used for cost-effective production of radionuclides. For the post-accelerator the choice of ion source technology is critical and dictates the charge-to-mass requirements at the injection stage

Decommissioning strategies for facilities using radioactive material

International Nuclear Information System (INIS)

2007-01-01

The planning for the decommissioning of facilities that have used radioactive material is similar in many respects to other typical engineering projects. However, decommissioning differs because it involves equipment and materials that are radioactive and therefore have to be handled and controlled appropriately. The project management principles are the same. As with all engineering projects, the desired end state of the project must be known before the work begins and there are a number of strategies that can be used to reach this end state. The selection of the appropriate strategy to be used to decommission a facility can vary depending on a number of factors. No two facilities are exactly the same and their locations and conditions can result in different strategies being considered acceptable. The factors that are considered cover a wide range of topics from purely technical issues to social and economic issues. Each factor alone may not have a substantial impact on which strategy to select, but their combination could lead to the selection of the preferred or best strategy for a particular facility. This Safety Report identifies the factors that are normally considered when deciding on the most appropriate strategy to select for a particular facility. It describes the impact that each factor can have on the strategy selection and also how the factors in combination can be used to select an optimum strategy

Current Measures on Radioactive Contamination in Japan: A Policy Situation Analysis.

Directory of Open Access Journals (Sweden)

Stuart Gilmour

Full Text Available The Great East Japan Earthquake on 11th March 2011 and the subsequent Fukushima Dai-ichi nuclear power plant disaster caused radioactive contamination in the surrounding environment. In the immediate aftermath of the accident the Government of Japan placed strict measures on radio-contamination of food, and enhanced radio-contamination monitoring activities. Japan is a pilot country in the WHO Foodborne Disease Burden Epidemiology Reference Group (FERG, and through this initiative has an opportunity to report on policy affecting chemicals and toxins in the food distribution network. Nuclear accidents are extremely rare, and a policy situation analysis of the Japanese government's response to the Fukushima Dai-ichi nuclear accident is a responsibility of Japanese scientists. This study aims to assess Japan government policies to reduce radio-contamination risk and to identify strategies to strengthen food policies to ensure the best possible response to possible future radiation accidents.We conducted a hand search of all publicly available policy documents issued by the Cabinet Office, the Food Safety Commission, the Ministry of Health, Labor and Welfare (MHLW, the Ministry of Agriculture, Forestry and Fishery (MAFF and prefectural governments concerning food safety standards and changes to radiation and contamination standards since March 11th, 2011. We extracted information on food shipment and sales restrictions, allowable radio-contamination limits, monitoring activities and monitoring results. The standard for allowable radioactive cesium (Cs-134 and Cs-137 of 100 Bq/Kg in general food, 50 Bq/Kg in infant formula and all milk products, and 10 Bq/Kg in drinking water was enforced from April 2012 under the Food Sanitation Law, although a provisional standard on radio-contamination had been applied since the nuclear accident. Restrictions on the commercial sale and distribution of specific meat, vegetable and fish products were released for

Protection against radioactive contamination of food and agricultural products

International Nuclear Information System (INIS)

Szabo, A.; Kovacs, Z.

1977-01-01

Due to contaminating effects from nuclear explosions and nuclear power plants, the systematic investigation of environmental radioactive contamination is absolutely necessary. In order to reduce the artificial radiation dose to which the human body is exposed, isotope content of foods and agricultural products should be known. The authors evaluate the decontamination possibilities of food produced from vegetable and animal products, starting from the contamination of some products. For vegetable product decontamination the use of suitable fertilizers, thorough scrubbing in excess water and, for cereals, milling is proposed. As the most effective preventive measure of radiation contamination of food products of animal origin, appropriate packing is proposed. The storage and preservation problems are emphasized for short half-life radiation contamination. (P.J.)

Radioactive contamination of aquatic media and organisms; La contamination radioactive des milieux et des organismes aquatiques

Energy Technology Data Exchange (ETDEWEB)

Fontaine, Y. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1960-07-01

After a brief account of the radioactive wastes produced by peaceful or military uses of Atomic Industry, the author first describes a series of observations carried out 'in the field' on the extent of contamination in aquatic organisms with respect to that of the medium. The experimental studies are then analysed, with reference both to the radioisotope metabolism and to the factors and types of contamination of aquatic organisms by wastes from atomic industry. A precise experimental project is presented at the end of the paper, including almost 300 references. (author) [French] Apres une courte etude des dechets radioactifs produits par les utilisations pacifiques ou militaires de l'Industrie Atomique, l'auteur fait etat d'abord des observations effectuees 'sur le terrain' concernant l'extension de la contamination des organismes aquatiques en rapport avec celle du milieu. L'auteur analyse ensuite les etudes experimentales se rapportant aussi bien au metabolisme des radioisotopes qu'aux facteurs et aux modalites de la contamination des organismes aquatiques par les dechets de l'industrie atomique. Un projet de travail experimental precis est presente a la fin de cette revue qui comporte pres de 300 references bibliographiques. (auteur)

Design and operation of off-gas cleaning and ventilation systems in facilities handling low and intermediate level radioactive material

International Nuclear Information System (INIS)

1988-01-01

The number of developing countries constructing new nuclear facilities is increasing. These facilities include the production and processing of radioisotopes, as well as all types of laboratories and installations, which handle radioactive material and deal with the treatment of radioactive wastes. Ventilation and air cleaning systems are a vital part of the general design of any nuclear facility. The combination of a well designed ventilation system with thorough cleaning of exhaust air is the main method of preventing radioactive contamination of the air in working areas and in the surrounding atmosphere. This report provides the latest information on the design and operation of off-gas cleaning and ventilation systems for designers and regulatory authorities in the control and operation of such systems in nuclear establishments. The report presents the findings of an Advisory Group Meeting held in Vienna from 1 to 5 December 1986 and attended by 12 experts from 11 Member States. Following this meeting, a revised report was prepared by the International Atomic Energy Agency Secretariat and three consultants, M.J. Kabat (Canada), W. Stotz (Federal Republic of Germany) and W.A. Fairhurst (United Kingdom). The final draft was commented upon and approved by the participants of the meeting. 69 refs, 37 figs, 12 tabs

Materials and Security Consolidation Complex Facilities Radioactive Waste Management Basis and DOE Manual 435.1-1 Compliance Tables

International Nuclear Information System (INIS)

2011-01-01

Department of Energy Order 435.1, 'Radioactive Waste Management,' along with its associated manual and guidance, requires development and maintenance of a radioactive waste management basis for each radioactive waste management facility, operation, and activity. This document presents a radioactive waste management basis for Idaho National Laboratory's Materials and Security Consolidation Center facilities that manage radioactive waste. The radioactive waste management basis for a facility comprises existing laboratory-wide and facility-specific documents. Department of Energy Manual 435.1-1, 'Radioactive Waste Management Manual,' facility compliance tables also are presented for the facilities. The tables serve as a tool for developing the radioactive waste management basis.

A model for evaluating the radioactive contamination in the urban environment

International Nuclear Information System (INIS)

Hwang, Won Tae; Kim, Eun Han; Jeong, Hyo Joon; Suh, Kyung Suk; Han, Moon Hee

2005-01-01

A model for evaluating radioactive contamination in the urban environment, named METRO-K, was developed as a basic step for accident consequence analysis in case of an accidental release. The three kind of radionuclides ( 137 Cs, 106 Ru, 131 I) and the different chemical forms of iodine (particulate, organic and elemental forms) are considered in the model. The radioactive concentrations are evaluated for the five types of surface (roof, paved road, wall, lawn/soil, tree) as a function of time. Using the model, the contaminative impacts of the surfaces were intensively investigated with respect to with and without precipitation during the measurement periods of radionuclides in air. In addition, a practical application study was conducted using 137 Cs concentration in air and precipitation measured in an European country at the Chernobyl accident. As a result, precipitation was an influential factor in surface contamination. The degree of contamination was strongly dependent on the types of radionuclide and surface. Precipitation was more influential in contamination of 137 Cs than that of 131 I (elemental form)

Imaging plant leaves to determine changes in radioactive contamination status in Fukushima, Japan.

Science.gov (United States)

Nakajima, Hiroo; Fujiwara, Mamoru; Tanihata, Isao; Saito, Tadashi; Matsuda, Norihiro; Todo, Takeshi

2014-05-01

The chemical composition of plant leaves often reflects environmental contamination. The authors analyzed images of plant leaves to investigate the regional radioactivity ecology resulting from the 2011 accident at the Fukushima No. 1 nuclear power plant, Japan. The present study is not an evaluation of the macro radiation dose per weight, which has been performed previously, but rather an image analysis of the radioactive dose per leaf, allowing the capture of various gradual changes in radioactive contamination as a function of elapsed time. In addition, the leaf analysis method has potential applications in the decontamination of food plants or other materials.

Residual radioactive contamination at Maralinga and Emu, 1985

International Nuclear Information System (INIS)

Lokan, K.H.

1985-04-01

An account is provided of residual contamination at Maralinga and Emu, in South Australia, where the United Kingdom Atomic Weapons Research Establishment conducted nuclear weapons development trials between 1953 and 1963. Detailed information is presented about contamination levels at sites on the range where radioactive materials were dispersed. Some of these were associated with trials involving natural uranium or short-lived isotopes which are no longer present. There are four sites where plutonium-239 was dispersed in substantial quantities from minor trials and information is presented about its distribution. Much of this material has been diluted by mixing with local soil, but there is a significant quantity of material present in the form of contaminated fragments, particularly at Taranaki. A considerable quantity of uranium-235 is also present at Taranaki. An assessment is made of the radiological significance of the dispersed plutonium and it is concluded that the material represents a potential long term hazard while it remains in its present form. Residual radioactivity associated with all but one of the seven major trial sites involving nuclear explosions continues to decay in a predictable way and will in the worst case, fall below levels considered safe for continuous occupancy within about fifty years. One site, Tadje, contains significant concentrations of plutonium over a small area and onsidered to be an additional plutonium-contaminated locality. Measurements of beryllium concentrations in soil are presented

Near-surface facilities for disposal radioactive waste from non-nuclear application

International Nuclear Information System (INIS)

Barinov, A.

2000-01-01

The design features of the near-surface facilities of 'Radon', an estimation of the possible emergency situations, and the scenarios of their progress are given. The possible safety enhancing during operation of near-surface facilities, so called 'Historical facilities', and newly developed ones are described. The Moscow SIA 'Radon' experience in use of mobile module plants for liquid radioactive waste purification and principal technological scheme of the plant are presented. Upgrading of the technological scheme for treatment and conditioning of radioactive waste for new-developed facilities is shown. The main activities related to management of spent ionizing sources are mentioned

A Novel Method for Remote Depth Estimation of Buried Radioactive Contamination.

Science.gov (United States)

Ukaegbu, Ikechukwu Kevin; Gamage, Kelum A A

2018-02-08

Existing remote radioactive contamination depth estimation methods for buried radioactive wastes are either limited to less than 2 cm or are based on empirical models that require foreknowledge of the maximum penetrable depth of the contamination. These severely limits their usefulness in some real life subsurface contamination scenarios. Therefore, this work presents a novel remote depth estimation method that is based on an approximate three-dimensional linear attenuation model that exploits the benefits of using multiple measurements obtained from the surface of the material in which the contamination is buried using a radiation detector. Simulation results showed that the proposed method is able to detect the depth of caesium-137 and cobalt-60 contamination buried up to 40 cm in both sand and concrete. Furthermore, results from experiments show that the method is able to detect the depth of caesium-137 contamination buried up to 12 cm in sand. The lower maximum depth recorded in the experiment is due to limitations in the detector and the low activity of the caesium-137 source used. Nevertheless, both results demonstrate the superior capability of the proposed method compared to existing methods.

Steps for safety. Radioactive waste management facilities and Y2K

International Nuclear Information System (INIS)

Warnecke, E.

1999-01-01

As part of the IAEA activities concerned with Year 2000 (Y2K) problem special attention is paid to operation of radioactive waste management facilities although, fortunately, in the management of radioactive materials the response of a process or activity to a failure would be slow in many instance, providing more time to resolve the issue before any radiological consequences occur. To facilitate greater cooperation, the IAEA organized an international workshop on the exchange of information concerning safety measure to address the Y2K issues on radioactive waste management and nuclear fuel cycle facilities

An assessment of radioactivity level in 51Cr-contaminated dry solid waste generated from a research facility for verification of clearance levels

International Nuclear Information System (INIS)

Nagamatsu, Tomohiro; Yamaoka, Kiyonori; Hanafusa, Tadashi; Ono, Toshiro

2010-01-01

Radioactive waste generated from research laboratories and other facilities is regulated by the Law Concerning Prevention from Radiation Hazards due to Radioisotopes etc. (Prevention Law). However, the Prevention Law does not provide the level of clearance or the procedures to follow for compliance monitoring. To assess radioactivity amounts for making decisions about clearance levels, the radioactivity levels in dry solid semi-combustible wastes generated from biomedical research, such as 51 Cr-release assays, were measured and evaluated. Radioactivity of semi-combustible waste was 1.42-6.32% of the initial level. In comparison, records for the past 8 years in the Shikata Laboratory, Department of Radiation Research, Okayama University Advanced Science Research Center, indicated 7% to 90% of the initial radioactivity remained in the waste and was differed widely among researchers. This study determined an accurate radioactivity level in dry solid waste, which could lead to savings in disposal costs. (author)

Influence of radioactive contamination to agricultural products by rainfall during a nuclear accident

International Nuclear Information System (INIS)

Hwang, W. T.; Han, M. H.; Choi, Y. H.; Lee, H. S.; Lee, C. W.

2001-01-01

For the consideration of the effects on radioactive contamination of agricultural products by rainfall during a nuclear accident, the wet interception coefficients for the plants were derived, and the previous dynamic food chain model was also modified. From the results, radioactive contamination of agricultural products was greatly decreased by rainfall, and it decreased dramatically according to increase of rainfall amount. It means that the predictive contamination in agricultural products using the previous dynamic food chain model, in which dry interception to the plants is only considered, can be overestimated. Influence of rainfall on the contamination of agricultural products was the most sensitive for 131 I, and the least sensitive for 90 Sr

Transfer of radioactive contamination from milk to commercial dairy products

International Nuclear Information System (INIS)

Wilson, L.G.; Sutton, P.M.

1988-01-01

The fate of radioactive contamination resulting from fallout from the Chernobyl accident was studied during milk processing. A range of commercial dairy products was produced on a pilot-laboratory scale and the radiocaesium contents were measured by high-resolution gamma spectrometry. The results show that the radiocaesium partitioned with the water phase and therefore butter, cream and cheese had relatively low levels of radioactivity. Ion exchange demineralization was effective in removing radiocaesium from whey. Ultrafiltration of whey resulted in a reduction of radioactivity relative to retentate solids. (author)

Use of ion exchange and early treatment of radioactive contamination in the digestive tract; Utilisation des echangeurs d'ions et traitement precoce de la contamination radioactive par voie digestive

Energy Technology Data Exchange (ETDEWEB)

Michon, G; Guilloux, M J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

The efficiency of cation exchange resins for the treatment of digestive contamination with strontium has been studied on rats. The results obtained show that the most efficient resins are those of sulfonic type when administered in the ammonium form. The treatment is still efficient when applied 45 minutes after the ingestion of strontium. In the most favourable cases, the radioactivity of the skeleton was lower by a factor 6 in the treated animals than in controls. This easily applicable, rather safe and non specific treatment deserves to be retained for use. (author) [French] Une etude de l'efficacite des resines echangeuses de cations dans le traitement d'une contamination digestive par le strontium a ete entreprise chez le rat. Les resultats montrent que parmi les resines, les plus efficaces sont celles de type sulfonique, administrees sous forme ammonium. Le traitement est encore efficace 45 minutes apres l'ingestion du strontium. Dans les meilleurs cas, le squelette des rats traites etait six fois moins radioactif que celui des temoins. Ce traitement d'emploi facile, peu dangereux, non specifique, merite d'etre retenu. (auteur)

Development of Decontamination Technology for Separating Radioactive Constituents from Contaminated Concrete Waste

International Nuclear Information System (INIS)

Min, B. Y.; Kim, G. N.; Lee, G. W.; Choi, W. K.; Jung, U. S.

2010-01-01

The large amount of contaminated concrete produced during decommissioning procedures and available decontamination. In Korea, more than more than 60 tons of concrete wastes contaminated with uranium compounds have been generated from UCP (Uranium Conversion Plant) by dismantling. A recycling or a volume reduction of the concrete wastes through the application of appropriate treatment technologies have merits from the view point of an increase in a resource recycling as well as a decrease in the amount of wastes to be disposed of resulting in a reduction of a disposal cost and an enhancement of the disposal safety. For unconditional release of building and reduction of radioactive concrete waste, mechanical methods and thermal stress methods have been selected. In the advanced countries, such as France, Japan, Germany, Sweden, and Belgium, techniques for reduction and reuse of the decommissioning concrete wastes have applied to minimize the total radioactive concrete waste volume by thermal and mechanical processes. It was found that volume reduction of contaminated concrete can be achieved by separation of the fine cement stone and coarse gravel. Typically, the contaminated layer is only 1∼10mm thick because cementitious materials are porous media, the penetration of radionuclides may occur up to several centimenters from the surface of a material. Most of the dismantled concrete wastes are slightly contaminated rather than activated. This decontamination can be accomplished during the course of a separation of the concrete wastes contaminated with radioactive materials through a thermal treatment step of the radionuclide (e.g. cesium and strontium), transportation of the radionuclide to fine aggregates through a mechanical treatment step. Concrete is a structural material which generally consists of a binder (cement), water, and aggregate. The interaction between highly charged calcium silicate hydrate (C-S-H) particles in the presence of divalent calcium

Responses of the soil decomposer community to the radioactive contamination

International Nuclear Information System (INIS)

Svetlana, Maksimova

2004-01-01

The knowledge about biodiversity and about reasons and laws of dynamics of decomposer invertebrates has exclusively important (rather applied, or theoretical) significance for soil science. Earthworms and millipedes are probably the most important members of the soil biota and major contributors to total zoo-mass. Their activities are such that they are extremely important in maintaining soil fertility in a variety of ways. They play an important part in the redistribution of radionuclides accumulated in the natural biogeocenoses and accumulation of radionuclides in their bodies depends on their concentration in the habitat. Since radionuclides can limit biological activity, studies to estimate the tolerance of decomposer community to potentially toxic radiators are needed. The effect of radioactive contamination on the soil invertebrates and decomposition processes in the different biogeocenoses we intensively studied during 17 years after Chernobyl accident. The soil invertebrates were collected according to generally accepted method by M. Ghilyarov. Soil samples were 0,25 m 2 and animals were extracted from samples by hand sorting. Usually decomposition was affected by the presence of decomposer fauna. Considerable differences were found in the species number. The species composition of sites differed clearly. The study showed that the fauna was poorer under increasing levels of radioactive contamination. The higher radionuclide content was found to result in suppression of decomposer community. The results showed a vertical migration of earthworms to deeper soil layers with increasing of radioactive contamination. With the absence of decomposer fauna due to migration to the deeper layer and mortality, the layer of litter increased. The results show that the earthworms were of small size. Cocoon production decreased. Radioactive contamination altered the process of reproduction and age structure of decomposer fauna. The invertebrates collected from the

Responses of the soil decomposer community to the radioactive contamination

Energy Technology Data Exchange (ETDEWEB)

Svetlana, Maksimova [Institute of Zoology of National Academy of Sciences of Belarus, Minsk (Belarus)

2004-07-01

The knowledge about biodiversity and about reasons and laws of dynamics of decomposer invertebrates has exclusively important (rather applied, or theoretical) significance for soil science. Earthworms and millipedes are probably the most important members of the soil biota and major contributors to total zoo-mass. Their activities are such that they are extremely important in maintaining soil fertility in a variety of ways. They play an important part in the redistribution of radionuclides accumulated in the natural biogeocenoses and accumulation of radionuclides in their bodies depends on their concentration in the habitat. Since radionuclides can limit biological activity, studies to estimate the tolerance of decomposer community to potentially toxic radiators are needed. The effect of radioactive contamination on the soil invertebrates and decomposition processes in the different biogeocenoses we intensively studied during 17 years after Chernobyl accident. The soil invertebrates were collected according to generally accepted method by M. Ghilyarov. Soil samples were 0,25 m{sup 2} and animals were extracted from samples by hand sorting. Usually decomposition was affected by the presence of decomposer fauna. Considerable differences were found in the species number. The species composition of sites differed clearly. The study showed that the fauna was poorer under increasing levels of radioactive contamination. The higher radionuclide content was found to result in suppression of decomposer community. The results showed a vertical migration of earthworms to deeper soil layers with increasing of radioactive contamination. With the absence of decomposer fauna due to migration to the deeper layer and mortality, the layer of litter increased. The results show that the earthworms were of small size. Cocoon production decreased. Radioactive contamination altered the process of reproduction and age structure of decomposer fauna. The invertebrates collected from the

Experimental study of contamination by inhalation of radioactive iodine aerosols. Biological balance

International Nuclear Information System (INIS)

Marble, G.

1968-01-01

Several articles have been published concerning research into contamination produced by inhalation of radioactive iodine aerosols in monkeys. Results dealing with the biological balance of this contamination are presented and discussed in this report. (author) [fr

Standards and guidelines pertinent to the development of decommissioning criteria for sites contaminated with radioactive material

International Nuclear Information System (INIS)

Dickson, H.W.

1978-08-01

A review of existing health and safety standards and guidelines has been undertaken to assist in the development of criteria for the decontamination and decommissioning of property contaminated with radioactive material. During the early years of development of the nuclear program in the United States, a number of sites were used which became contaminated with radioactive material. Many of these sites are no longer useful for nuclear activities, and the U.S. DOE desires to develop criteria for the management of these sites for future uses. Radiation protection standards promulgated by ICRP, NCRP, and ANSI have been considered. Government regulations, from the Code of Federal Regulations and the legal codes of various states, as well as regulatory guidelines with specific application to decommissioning of nuclear facilities also have been reviewed. In addition, recommendations of other scientific organizations such as the National Academy of Sciences/National Research Council Advisory Committee on the Biological Effects of Ionizing Radiations and the United Nations Scientific Committee on the Effects of Atomic Radiation were considered. Finally, a few specific recommendations and discussions from current literature were included. 28 references

The Norwegian Radiation Protection Authority leads international cooperation on radioactive contamination in the Arctic

International Nuclear Information System (INIS)

1995-01-01

In cooperation with Russia, Norway is responsible for the part of Arctic Monitoring and Assessment Programme (AMAP) concerning radioactivity. An assessment of the consequences of radioactive contamination for the environment in northern areas will be an important part of AMAP's report to the Ministers of the Environment in the eight participating countries in 1996. The report will contain an overview of the sources of the contamination and the level of radioactivity in the environment, in addition to an evaluation of the consequences for humans and the environment

Disposal sheet for preventing scattering of radioactive contaminated material

International Nuclear Information System (INIS)

Miyasaka, Shun-ichi; Kurioka, Hitoshi; Nakamura, Kenjiro.

1990-01-01

Upon disposal of vinyl sheets at the final stage of dismantling operation for nuclear buildings, etc., radioactive contaminated materials caused by cutting concretes, etc. remain on the sheets. In view of the above, members capable of restoring original shape due to the temperature difference are attached to the sheet main body so that the sheet main body may be folded into a bag-like shape. Since the members as described above are bent upon temperature elevation in the sheets, the sheet main body is pulled by the members and then spontaneously folded into a bag-like shape. As a result, the radioactive contaminated materials remaining on the sheets are wrapped into the sheet main body free from touch to operator's hands or without scattering to the surrounding. This can prevent operator's external and internal exposure. (T.M.)

The action and problem of the decontamination work of the radioactive contamination soil starting in earnest

International Nuclear Information System (INIS)

Omura, Tomomi

2011-01-01

At the stage of just eight months after the time when a large amount of radioactivity was discharged by the accident of the Fukushima Daiichi Nuclear Station of Tokyo Electric Power Company associated with the Great East Japan Earthquake, countermeasures for pollution due to radioactive substances have become the biggest challenge. The government made a cabinet decision on basic policy based on 'The Act on Special Measures concerning the Handling of Environmental Pollution by Radioactive Materials Discharged by the Nuclear Power Station Accident Associated with the Tohoku District - Off the Pacific Ocean Earthquake that Occurred on March 11, 2011 (The Act on Special Measures concerning the Handling of Radioactive Pollution).' By this, fiscal measures, regulatory measures, and role-sharing required for promoting the treatment of radioactivity-contaminated disaster waste and the decontamination measures of soil were clarified. At the same time as the enactment of the bill, 'Basic Policy for Emergency Response on Decontamination Work' and 'Guidelines for Municipal Decontamination Work' were issued, which helped a step toward full-scale decontamination activities with the backup of budgetary measures. This paper explains the following efforts of the government in implementing these actions. Installation of temporary storage sites for decontaminated soil, implementation of interim storage facilities, development of final disposal sites, and budgetary support. (O.A.)

[Decorporation agents for internal radioactive contamination].

Science.gov (United States)

Ohmachi, Yasushi

2015-01-01

When radionuclides are accidentally ingested or inhaled, blood circulation or tissue/organ deposition of the radionuclides causes systemic or local radiation effects. In such cases, decorporation therapy is used to reduce the health risks due to their intake. Decorporation therapy includes reduction and/or inhibition of absorption from the gastrointestinal tract, isotopic dilution, and the use of diuretics, adsorbents, and chelating agents. For example, penicillamine is recommended as a chelating agent for copper contamination, and diethylene triamine pentaacetic acid is approved for the treatment of internal contamination with plutonium. During chelation therapy, the removal effect of the drugs should be monitored using a whole-body counter and/or bioassay. Some authorities, such as the National Council on Radiation Protection and Measurements and International Atomic Energy Agency, have reported recommended decorporation agents for each radionuclide. However, few drugs are approved by the US Food and Drug Administration, and many are off-label-use agents. Because many decontamination agents are drugs that have been available for a long time and have limited efficacy, the development of new, higher-efficacy drugs has been carried out mainly in the USA and France. In this article, in addition to an outline of decorporation agents for internal radioactive contamination, an outline of our research on decorporation agents for actinide (uranium and plutonium) contamination and for radio-cesium contamination is also presented.

USING STATISTICAL PROCESS CONTROL TO MONITOR RADIOACTIVE WASTE CHARACTERIZATION AT A RADIOACTIVE FACILITY

International Nuclear Information System (INIS)

WESTCOTT, J.L.

2006-01-01

Two facilities for storing spent nuclear fuel underwater at the Hanford site in southeastern Washington State being removed from service, decommissioned, and prepared for eventual demolition. The fuel-storage facilities consist of two separate basins called K East (KE) and K West (KW) that are large subsurface concrete pools filled with water, with a containment structure over each. The basins presently contain sludge, debris, and equipment that have accumulated over the years. The spent fuel has been removed from the basins. The process for removing the remaining sludge, equipment, and structure has been initiated for the basins. Ongoing removal operations generate solid waste that is being treated as required, and then disposed. The waste, equipment and building structures must be characterized to properly manage, ship, treat (if necessary), and dispose as radioactive waste. As the work progresses, it is expected that radiological conditions in each basin may change as radioactive materials are being moved within and between the basins. It is imperative that these changing conditions be monitored so that radioactive characterization of waste is adjusted as necessary

USING STATISTICAL PROCESS CONTROL TO MONITOR RADIOACTIVE WASTE CHARACTERIZATION AT A RADIOACTIVE FACILITY

International Nuclear Information System (INIS)

WESTCOTT, J.L.; JOCHEN; PREVETTE

2007-01-01

Two facilities for storing spent nuclear fuel underwater at the Hanford site in southeastern Washington State are being removed from service, decommissioned, and prepared for eventual demolition. The fuel-storage facilities consist of two separate basins called K East (KE) and K West (KW) that are large subsurface concrete pools filled with water, with a containment structure over each. The basins presently contain sludge, debris, and equipment that have accumulated over the years. The spent fuel has been removed from the basins. The process for removing the remaining sludge, equipment, and structure has been initiated for the basins. Ongoing removal operations generate solid waste that is being treated as required, and then disposed. The waste, equipment and building structures must be characterized to properly manage, ship, treat (if necessary), and dispose as radioactive waste. As the work progresses, it is expected that radiological conditions in each basin may change as radioactive materials are being moved within and between the basins. It is imperative that these changing conditions be monitored so that radioactive characterization of waste is adjusted as necessary

Fluctuating asymmetry of shape in rodents from radioactively contaminated environments at Chernobyl

International Nuclear Information System (INIS)

Smith, M.H.; Novak, J.M.; Oleksyk, T.K.; Purdue, J.R.; Gashchak, S.

2002-01-01

In this study we addressed the question of whether levels of fluctuating symmetry (FA) were elevated in the radioactively contaminated populations compared to reference populations of an abundant rodent living in both environments: the yellow - necked mouse (Apodemus flavicollis). We used six populations of these animals from both inside the radioactively contaminated area close to the failed Chornobyl reactor in Ukraine and in reference areas with no apparent contamination by radionuclides. Twenty-four landmarks on the ventral surface of the rodent's skulls were used to calculate the amounts of FA of shape using Procrustes methods. A higher level of FA was documented for the populations in closest proximity to the failed Chornobyl Nuclear Plant. This index was significantly higher in populations from the most contaminated locations in the Chornobyl Exclusion Zone than in the reference areas. On the other hand, populations from the less contaminated areas inside the Chornobyl Exclusion Zone did not express FA values different from those in the reference populations

The reality of radioactive contamination in construction of Taiwan and the treatment concerned

International Nuclear Information System (INIS)

Huang Chin-Wang

2005-01-01

It has been more than 50 years since Taiwan started the research on the peace application of radioactivity. During the first 20-30 years, it was found that the radioactive contaminated waste steel from atomic power plants was recycled together with general waste steel and was used to make other products including reinforcing bars. It was because the radiation resources ware not carefully controlled and managed. Since 1982, the radioactive contaminated reinforcing bars and buildings were gradually found, as the radiation dose rates were 5 μSv/h and 0.5 μSv/h, respectively. The radioactive nuclide was all Co-60. By August 2003, 1,626 households, 7,824 people's houses were founded to be radioactive contaminated. Furthermore, radiation dose rates higher than 5 μSv/h were measured from 264 of those householders. The government has started to ameliorate this situation and 94.7% of the cases have become normal. The cancer death rate of these people is found to be 0.49% (89 patients in 7,824 people, 39 was dead), and it is 4 times higher than that for general people. In order to solute this pollution problem, the government has made the law to check the radioactivity of all reinforcing bars and to control and manage those radiation resources more carefully. Additionally, there are tax exemption, subsidy, and expropriation with compensation for the polluted buildings. (author)

Radioactive releases from a thorium-contaminated site in Wayne, New Jersey

International Nuclear Information System (INIS)

Wang, J.; Yang, J.; Merry-Libby, P.

1985-01-01

Various residues and wastes from the production of thorium and rare earths from monazite ore are buried on a hillside in Wayne, New Jersey. In addition, contaminated materials (primarily soils) from nearby vicinity properties are being consolidated onto the Wayne site. The US Department of Energy plans to stabilize all the contaminated materials on an interim basis (20 years) until funding is available to remove them to another location. In order to evaluate the effectiveness of interim stabilization measures, pre-remedial action radioactive releases are compared to estimated releases under a reference stabilization option (one meter of soil cover). Two potential pathways are examined: (1) airborne radioactive gases (thoron and radon) and particulates, and (2) seepage into the near-surface groundwater. The relative reduction of releases into the air and groundwater for the reference stabilization option is analyzed using mathematical models for radioactive gas fluxes and atmospheric dispersion as well as groundwater transport and dispersion. The consequent health implications for nearby individuals and the general population are also estimated. Health effects due to radioactive releases are estimated to be insignificant

Radioactive sources and contaminated materials in scrap: monitoring, detection and remedial actions

International Nuclear Information System (INIS)

Gallini, R.; Berna, V.; Bonora, A.; Santini, M.

1999-01-01

The scrap recycling in steel and other metal mills represents one of the most relevant activities in the Province of Brescia (Lombardy, Italy). In our Province more than 20 million tonnes of metal scrap are recycled every year by a melting process. Since 1990, many accidents which took place were caused by the unwanted melting of radioactive sources, that were probably hidden in metal scrap. In 1993, the Italian Government stated directives to monitor metal scrap imported from non-EC countries because of the suspicion of the illegal traffic of radioactive materials. In 1996, a law imposed the control of all metal scrap, regardless of their origins. Since 1993, our staff have controlled thousands of railway wagons and trucks. Approximately a hundred steel mills and foundries of aluminium, cooper, brass, etc. have also been controlled and many samples have been collected (flue dust, slag, finished products). During these controls, contaminated areas have been brought to light in two warehouses (Cs 137), in 6 companies (Cs 137 and Am 241), in two landfills of industrial waste (Cs 137) and in a quarry (Cs 137). Up to now the contaminated areas have been cleaned, except for the last one. About 150 radioactive sources on contaminated materials have been found in metal scrap. We found radioactive sources of Co 60, Ra 226, Ir 192, Kr 85, Am 241, while the contamination of metals was mainly due to Ra 226. The situation described above justifies an accurate control of the amount of scrap to reduce the risk of contamination of the workers in the working areas, in the environment and in the general public. (author)

The changes in the ecology and physiology of soil invertebrates under influences of radioactive contamination

International Nuclear Information System (INIS)

Maksimova, S.

2006-01-01

The soil biota is important in building and maintaining soil structure and fertility. Invertebrates are ideal as potential bio indicators of the environmental impact of radioactive contamination: they are widely distributed, often abundant and generally thought of as having low dispersive capacity. They can use as test organisms to detect the side-effects of radioactive contamination. The long-term analysis of ecological and physiological after-effects and biodiversity changes had been studied in the zone of radioactive contamination. Material was collected in the Gomel Region (Belarus), 30 km away from the CNPP in 1986-2004 applying usual pedobiological techniques (soil samples and Barber's pitfall traps) at reference points subjected to radioactive contamination. Soil samples were collected at 0 to 25 cm depth. Samples were taken in locations, which had received considerable radionuclide contaminations. These sites differed in contamination by the composition of fall-out, the forms of radionuclide content in soils, their intake into trophic chains and accumulation in animal and plant organisms. The impacts have been investigated at the: 1) organism and population levels , in terms of individual life histories (birth rate, growth, mortality) or species selection; 2) at the community level: to species diversity and to effects on trophic structure. The invertebrates were determined to species or genera, including juvenile stages. Radioactive contamination caused a distinct decrease in species number; the dominance structure of the community changed. The saprophagous are especially sensitive to environmental disturbances. An initial sharp reduction of animal biodiversity and simplification of the community structure of soil fauna were observed, followed by a long-term process of returning to the initial parameters. Changes in hemolymph, necroses of epithelium and cell structure in connective tissue were registered. The most drastic after-effects were manifested in

Radiological risk assessment of a radioactively contaminated site

International Nuclear Information System (INIS)

Devgun, J.S.

1990-01-01

A limited-scope preliminary assessment of radiological risk has been conducted at a radioactively contaminated site under current site use conditions and based on the available preliminary radiological characterization data for the site. The assessment provides useful input to the remedial action planning for the site. 8 refs., 1 fig., 2 tabs

A Review of Removable Surface Contamination on Radioactive Materials Transportation Containers

Energy Technology Data Exchange (ETDEWEB)

Kennedy, Jr, W. E.; Watson, E. C.; Murphy, D. W.; Harrer, B. J.; Harty, R.; Aldrich, J. M.

1981-05-01

This report contains the results of a study sponsored by the U.S. Nuclear Regulatory Commission (NRC) of removable surface contamination on radioactive materials transportation containers. The purpose of the study is to provide information to the NRC during their review of existing regulations. Data was obtained from both industry and literature on three major topics: 1) radiation doses, 2) economic costs, and 3) contamination frequencies. Containers for four categories of radioactive materials are considered including radiopharmaceuticals, industrial sources, nuclear fuel cycle materials, and low-level radioactive waste. Assumptions made in this study use current information to obtain realistic yet conservative estimates of radiation dose and economic costs. Collective and individual radiation doses are presented for each container category on a per container basis. Total doses, to workers and the public, are also presented for spent fuel cask and low-level waste drum decontamination. Estimates of the additional economic costs incurred by lowering current limits by factors of 10 and 100 are presented. Current contamination levels for each category of container are estimated from the data collected. The information contained in this report is designed to be useful to the NRC in preparing their recommendations for new regulations.

Contaminated Land Remediation on decommissioned nuclear facilities: an optimized approach

International Nuclear Information System (INIS)

Sauer, Emilie

2016-01-01

The site of the Monts d'Arree located in Brennilis in the area of Brittany in France is a former 70 MWe heavy water reactor. EDF is now in charge of its decommissioning. The effluent treatment facility (STE) is currently being dismantled. As the future use of the site will exclude any nuclear activity, EDF is taking site release into consideration. Therefore a land management strategy for the land and soil is needed. An optimized approach is being proposed for the STE, to the French Regulator. In France, there is no specific regulation related to contaminated land (either radiologically contaminated or chemically contaminated). The French Nuclear Safety Authority's doctrine for radioactively contaminated land is a reference approach which involves complete clean-up, removing any trace of artificial radioactivity in the ground. If technical difficulties are encountered or the quantity of radioactive waste produced is too voluminous, an optimised clean-up can be implemented. EDF has been engaged since 2008 in drawing up a common guideline with other French nuclear operators (CEA and AREVA). The operators' guideline proposed the first steps to define how to optimise nuclear waste and to carry out a cost-benefits analysis. This is in accordance with the IAEA's prescriptions. Historically, various incidents involving effluent drum spills caused radiological contamination in the building platform and the underlying soil. While conducting the decontamination works in 2004/2005, it was impossible to remove all contamination (that went deeper than expected). A large characterization campaign was carried out in order to map the contamination. For the site investigation, 34 boreholes were drilled from 2 to 5 m under the building platform and 98 samples were analyzed to search for gamma, beta and alpha emitters. With the results, the contamination was mapped using a geostatistical approach developed by Geovariances TM . Main results were: - Soils are

Measurement of gamma radioactivity in steel

International Nuclear Information System (INIS)

Wachtendonk, H.J. von; Flock, J.; Grientschnig, D.; Kircher, T.; Kroos, J.; Mertens, S.; Mueller, J.; Puchmayr, J.; Schlothmann, B.J.; Schmitz, H.U.; Troebs, V.; Unger, H.

1999-01-01

The steel industry is being confronted increasingly with radioactive scrap from dismantled nuclear facilities. The clearance and release regulations that exist around the world differ very greatly and are difficult to implement. A 'radioactivity measurement' working group has therefore been set up at VDEh to clarify how radioactive measurements can be integrated into the day-to-day production routine. Operating results obtained at Thyssen Krupp Stahl AG with a gamma-ray spectrometer indicate a possibility for the simple detection of radioactive contamination. (orig.) [de

Aquatic ecosystems within the Chernobyl NPP exclusion zone: radioactive contamination, doses and effects

International Nuclear Information System (INIS)

Gudkov, D.I.; Kuzmenko, M.I.; Krot, Y.G.; Kipnis, L.S.; Mardarevich, M.G.; Ponomaryov, A.V.; Derevets, V.V.; Nazarov, A.B.

2003-01-01

For past 17 years after accident the character of radioactive contamination of water objects within the Chernobyl NPP exclusion zone has undergone essential changes. First of all it connected with realisation on a wide area of deactivation works, and also with transformation of radioactive substances in water-soil systems. Besides, during 1991-95 the complex of hydraulic engineering structures as protection dams, interfering washing away of radioactive substances from soils of the left-bank catchment basin and changed a hydrological regime of these territories during a high water, was constructed. The levels of radionuclide contamination of water objects within the Chernobyl NPP exclusion zone was rather stabilised. Due to high water change rate the river bottom sediments have undergone decontamination processes (especially during floods and periods of high water) and over the years have ceased to play the essential role as a secondary source of water contamination. On the other hand, the closed reservoirs have considerably higher levels of radioactive contamination caused by limited water change and by relatively high concentration of radionuclides deposited in the bottom sediments. Therefore, for the majority of standing reservoirs the level of radionuclide content is determined mainly by the rates of mobile radionuclide forms exchange between bottom sediment and water, as well as by the external washout from the catchment basin. In this paper will be considered: (1) the latest data on radionuclide content (Sr-90, Cs-137, Pu-238, Pu-239+240 and Am-241) and dynamics in water, seston, bottom sediments and hydrobionts of different trophic levels and ecological groups; (2) the peculiarities of formation of vegetative communities from lakes within embankment territory of Pripyat River flood-lands and its impact on radionuclide redistribution in aquatic ecosystems; (3) the major hydrochemical factors, which determine the behaviour of radionuclides in the aquatic

Radioactive contamination of honey and other bee-keeping products

International Nuclear Information System (INIS)

Frantsevich, L.I.; Komissar, A.D.; Levchenko, I.A.

1990-01-01

Great amount of dust is collected in propolis under emergency atmospheric fallouts. Specific coefficient of the product migration amounts to several m 2 per 1 kg. Propolis is a good biological indicator of radioactive fallouts. The propolis collection is inadmissible after radioactive fallouts. Cocoon residuals obtained during bees-wax separation contain many radionuclides and should be disposed in special places. Nuclides are absent in bees-wax. Nuclides accumulated absent in a bee organism migrate into honey and queen milk, the honey is contaminated mainly via biogenic path

Site selection process for radioactive waste repository (radioactive facility) in Cuba as a fundamental safety criteria

International Nuclear Information System (INIS)

Vital, Jose Luis Peralta; Castillo, Reinaldo Gil; Chales Suarez, Gustavo; Rodriguez Reyes, Aymee

1999-01-01

The paper show the process of search carried out for the selection of the safest site in the National territory, in order to sitting the Facility (Repository) that will disposal the low and intermediate level radioactive wastes, as well as the possible Storage Facility for nuclear spent Fuel (radioactive wastes of high activity). We summarize the obtained Methodology and the Criterions of exclusion adopted for the development of the Process of site selection, as well as the current condition of the researches that will permit the obtaining of the nominative objectives. (author)

Experience base for Radioactive Waste Thermal Processing Systems: A preliminary survey

International Nuclear Information System (INIS)

Mayberry, J.; Geimer, R.; Gillins, R.; Steverson, E.M.; Dalton, D.; Anderson, G.L.

1992-04-01

In the process of considering thermal technologies for potential treatment of the Idaho National Engineering Laboratory mixed transuranic contaminated wastes, a preliminary survey of the experience base available from Radioactive Waste Thermal Processing Systems is reported. A list of known commercial radioactive waste facilities in the United States and some international thermal treatment facilities are provided. Survey focus is upon the US Department of Energy thermal treatment facilities. A brief facility description and a preliminary summary of facility status, and problems experienced is provided for a selected subset of the DOE facilities

Protection against radioactive contamination of foods and agricultural products

International Nuclear Information System (INIS)

Szabo, A.; Kovacs, Z.

1977-01-01

Methods suitable for diminishing radioactive contamination of foods and agricultural products and reducing at the same time the irradiation hazards for the human organism are dealt with. The possibilities for the decontamination of foods vegetal and of animal origin are discussed separately. (author)

EPA's technical methodology for the development of cleanup regulations for radioactively-contaminated soils and buildings

International Nuclear Information System (INIS)

Hull, H.B.; Doehnert, M.; Wolbarst, A.; Mauro, J.J.; Ralston, L.

1995-01-01

The total number of sites contaminated with radionuclides in the United States is in the thousands. These sites range in size from corners of laboratories to sprawling nuclear weapons facilities covering many square miles of land. The U.S. Environmental Protection Agency (EPA) is proposing regulations for the protection of the public from radionuclide contamination at sites that are to be cleaned up and released for public use. The rule will apply to site under the control of Federal agencies, and to sites licensed by the Nuclear Regulatory Commission (NRC) or NRC Agreement States. In support of this rulemaking, EPA is conducting a comprehensive technical analysis which will provide information on the volumes of soil requiring remediation at various possible dose and risk levels. The analysis will also provide information at different cleanup levels on the number of potential adverse health effects among people living or working on or near a site following the cleanup of its radioactive contamination. This paper summarizes the overall approach for the technical analysis. (author)

Radioactive clearance discharge of effluent from nuclear and radiation facilities

International Nuclear Information System (INIS)

Liu Xinhua; Xu Chunyan

2013-01-01

On the basis of the basic concepts of radiation safety management system exemption, exclusion and clearance, we expound that the general industrial gaseous and liquid effluent discharges are exempted or excluded, gaseous and liquid effluent discharged from nuclear and radiation facilities are clearance, and non-radioactive. The main purpose of this paper is to clarify the concepts, reach a consensus that the gaseous and liquid effluent discharged from nuclear and radiation facilities are non-radioactive and have no hazard to human health and natural environment. (authors)

The consequences of radioactive contamination of forest ecosystems due to Chernobyl accident

International Nuclear Information System (INIS)

Tikhomirov, F.A.; Shcheglova, A.I.

1997-01-01

The effect of forests on the radionuclide primary distribution in different components of the contaminated ecosystems is considered by the example of Chernobyl accident. A basic mathematical model is developed describing 137 Cs biogeochemical cycling under conditions of quasi-steady state radionuclide redistribution in the ecosystem. Forest ecosystems are proved to diminish radionuclide migration in the environment, and forest should be regarded as an important sanitary factor. The contribution of contaminated forests and forest products to the total irradiation dose to local population is estimated. Special countermeasures are elaborated in order to diminish unfavorable consequences of forest radioactive contamination. A long-term dynamics of radioactive situation in the forest ecosystems in forecasted and further studies on the subject are drafted

PROCESS OF DECONTAMINATING MATERIAL CONTAMINATED WITH RADIOACTIVITY

Science.gov (United States)

Overholt, D.C.; Peterson, M.D.; Acken, M.F.

1958-09-16

A process is described for decontaminating metallic objects, such as stainless steel equipment, which consists in contacting such objects with nltric acid in a concentration of 35 to 60% to remove the major portion of the contamination; and thereafter contacting the partially decontaminated object with a second solution containing up to 20% of alkali metal hydroxide and up to 20% sodium tartrate to remove the remaining radioactive contaminats.

Analysis of a Radioactive Release in a Nuclear Waste Disposal Facility

Energy Technology Data Exchange (ETDEWEB)

Poppiti, James [Dept. of Energy, Washington, DC (United States); Nelson, Roger [Dept. of Energy, Carlsbad, NM (United States); MacMillan, Walter J. [Nuclear Waste Partners, Carlsbad, NM (United States); Cunningham, Scott

2017-07-01

The Waste Isolation Pilot Plant (WIPP) is a 655-meter deep mine near Carlsbad, New Mexico, used to dispose the nation’s defense transuranic waste. Limited airborne radioactivity was released from a container of radioactive waste in WIPP on 14 February, 2014. As designed, a mine ventilation filtration system prevented the large scale release of contamination from the underground. However, isolation dampers leaked, which allowed the release of low levels of contaminants after the event until they were sealed. None of the exposed individuals received any recordable dose. While surface contamination was limited, contamination in the ventilation system and portions of the underground was substantial. High efficiency particulate air (HEPA) filters in the operating ventilation system ensure continued containment during recovery and resumption of disposal operations. However, ventilation flow is restricted since the incident, with all exhaust air directed through the filters. Decontamination and natural fixation by the hygroscopic nature of the salt host rock has reduced the likelihood of further contamination spread. Contamination control and ventilation system operability are crucial for resumption of operations. This article provides an operational assessment and evaluation of these two key areas.

Analysis of a Radioactive Release in a Nuclear Waste Disposal Facility

International Nuclear Information System (INIS)

Poppiti, James; Nelson, Roger; MacMillan, Walter J.; Cunningham, Scott

2017-01-01

The Waste Isolation Pilot Plant (WIPP) is a 655-meter deep mine near Carlsbad, New Mexico, used to dispose the nation's defense transuranic waste. Limited airborne radioactivity was released from a container of radioactive waste in WIPP on 14 February, 2014. As designed, a mine ventilation filtration system prevented the large scale release of contamination from the underground. However, isolation dampers leaked, which allowed the release of low levels of contaminants after the event until they were sealed. None of the exposed individuals received any recordable dose. While surface contamination was limited, contamination in the ventilation system and portions of the underground was substantial. High efficiency particulate air (HEPA) filters in the operating ventilation system ensure continued containment during recovery and resumption of disposal operations. However, ventilation flow is restricted since the incident, with all exhaust air directed through the filters. Decontamination and natural fixation by the hygroscopic nature of the salt host rock has reduced the likelihood of further contamination spread. Contamination control and ventilation system operability are crucial for resumption of operations. This article provides an operational assessment and evaluation of these two key areas.

Measures to detect and control radioactive contaminated metallurgical scrap at border checkpoints in Poland

International Nuclear Information System (INIS)

Smagala, G.

1999-01-01

The issue of radioactive contaminated metallurgical scrap has never received a high priority in Poland and in the international community. Since the dissolution of the former Soviet Union a higher attention has been given to the problem. Poland which is located between the West and East Europe has the obligation to develop and implement an effective prevention and detection system. The reasons to increase national control and detection system at the border checkpoints in Poland are to avoid the following risks: post Chernobyl contamination transports of commodities; transport of contaminated metal scrap; transfer of radioactive waste for their disposal or utilization; high risk of becoming a transit country of illicit trafficking of nuclear materials and radioactive sources. In order to avoid the above-mentioned risks, Poland initiated in 1990, a deployment of the portable radiation devices at the border checkpoints and, as of 1998, the number of installed instruments exceeded a hundred. This paper presents Poland's activities to detect contaminated scrap at its border checkpoints. (author)

ENVIRONMENTALLY SOUND DISPOSAL OF RADIOACTIVE MATERIALS AT A RCRA HAZARDOUS WASTE DISPOSAL FACILITY

International Nuclear Information System (INIS)

Romano, Stephen; Welling, Steven; Bell, Simon

2003-01-01

The use of hazardous waste disposal facilities permitted under the Resource Conservation and Recovery Act (''RCRA'') to dispose of low concentration and exempt radioactive materials is a cost-effective option for government and industry waste generators. The hazardous and PCB waste disposal facility operated by US Ecology Idaho, Inc. near Grand View, Idaho provides environmentally sound disposal services to both government and private industry waste generators. The Idaho facility is a major recipient of U.S. Army Corps of Engineers FUSRAP program waste and received permit approval to receive an expanded range of radioactive materials in 2001. The site has disposed of more than 300,000 tons of radioactive materials from the federal government during the past five years. This paper presents the capabilities of the Grand View, Idaho hazardous waste facility to accept radioactive materials, site-specific acceptance criteria and performance assessment, radiological safety and environmental monitoring program information

77 FR 20077 - Request for a License To Export Radioactive Waste

Science.gov (United States)

2012-04-03

... NUCLEAR REGULATORY COMMISSION Request for a License To Export Radioactive Waste Pursuant to 10 CFR..., 2012, radioactive waste tons of or disposal by a February 16, 2012, XW019, in the form of ash radioactive waste licensed facility 11005986. and non-conforming as contaminated in Mexico. material. ash and...

The social and special effects of siting a low-level radioactive waste disposal facility in rural Texas

International Nuclear Information System (INIS)

Murdock, S.H.; Hamm, R.R.

1987-01-01

As part of its assessment of the impacts of a low-level radioactive waste disposal facility in Hudspeth County, the Texas Low-Level Radioactive Waste Disposal Authority (TLLRWDA) sponsored an independent study of the social and special impacts of the facility. These impacts include ''standard'' social impacts (such as impacts on social structures and attitudes, values and perceptions and ''special'' social impacts (such as fear, anxiety, concerns related to equity, the health of future generations, etc.). This paper reports the results of this study. Personal interviews with 71 community leaders and 96 randomly selected county residents were conducted during the summer of 1986. The results suggest that the major concern relates to the contamination of ground water, but that suspicion about the equity of the siting process and about the safe management of wastes is extensive, even among the most knowledgeable respondents. Mitigation concerns center on health and safety issues for residents and on potential forms of mitigation for governmental jurisdictions for leaders. Responses were similar for leaders and residents and for persons in different parts of the county

Reduction of radioactive waste by improvement of conditioning facilities

Energy Technology Data Exchange (ETDEWEB)

Radde, E.

2014-07-01

The NES (Nuclear Engineering Seibersdorf) is the only radioactive waste conditions and storage facility in Austria. It manages waste originating from research, industry and medicine. Its main goal is, not only to treat and store waste safety, but also to optimize processes to further reduce the waste volume. To achieve this goal, the New Handling Facility was built. In this paper we will show how the waste volume can be easily reduced by optimizing the conditioning and waste stream process. The NES owns a water treatment plant for cleaning of active waste water, an incineration plant that is used to burn radioactive waste. (Author)

Radioactive waste problems in Russia

International Nuclear Information System (INIS)

Bridges, O.; Bridges, J.W.

1995-01-01

The collapse of the former Soviet Union, with the consequent shift to a market driven economy and demilitarisation, has had a profound effect on the nuclear and associated industries. The introduction of tighter legislation to control the disposal of radioactive wastes has been delayed and the power and willingness of the various government bodies responsible for its regulation is in doubt. Previously secret information is becoming more accessible and it is apparent that substantial areas of Russian land and surface waters are contaminated with radioactive material. The main sources of radioactive pollution in Russia are similar to those in many western countries. The existing atomic power stations already face problems in the storage and safe disposal of their wastes. These arise because of limited on site capacity for storage and the paucity of waste processing facilities. Many Russian military nuclear facilities also have had a sequence of problems with their radioactive wastes. Attempts to ameliorate the impacts of discharges to important water sources have had variable success. Some of the procedures used have been technically unsound. The Russian navy has traditionally dealt with virtually all of its radioactive wastes by disposal to sea. Many areas of the Barents, Kola and the Sea of Japan are heavily contaminated. To deal with radioactive wastes 34 large and 257 small disposal sites are available. However, the controls at these sites are often inadequate and illegal dumps of radioactive waste abound. Substantial funding will be required to introduce the necessary technologies to achieve acceptable standards for the storage and disposal of radioactive wastes in Russia. (author)

Deployment of Radioactive Waste Disposal Facility with the Introduction of Nuclear Power Plants in Kenya

Energy Technology Data Exchange (ETDEWEB)

Shadrack, Antoony; Kim, Changlak [KEPCO International Nuclear Graduate School, Uljin (Korea, Republic of)

2013-07-01

The nuclear power program will inevitably generate radioactive wastes including low-and intermediate radioactive waste and spent fuel. These wastes are hazardous to human health and the environment and therefore, a reliable radioactive waste disposal facility becomes a necessity. This paper describes Kenya's basic plans for the disposal of radioactive wastes expected from the nuclear program. This plan is important as an initial implementation of a national Low to intermediate level wastes storage facility in Kenya. In Kenya, radioactive waste is generated from the use of radioactive materials in medicine, industry, education and research and development. Future radioactive waste is expected to arise from nuclear reactors, oil exploration, radioisotope and fuel production, and research reactors as shown in table 1. The best strategy is to store the LILW and spent fuel temporarily within reactor sites pending construction of a centralized interim storage facility or final disposal facility. The best philosophy is to introduce both repository and nuclear power programs concurrently. Research and development on volume reduction technology and conceptual design of disposal facility of LILW should be pursued. Safe management of radioactive waste is a national responsibility for sustainable generation of nuclear power. The republic of Kenya is set to become the second African nuclear power generation country after South Africa.

Radioactive contamination, what actions for the polluted sites

International Nuclear Information System (INIS)

2004-01-01

The nuclear safety authority and the direction of prevention of pollutions and risks have organised the first edition of the national colloquium: radioactive contamination: what actions for polluted sites. Four axes can be taken to follow this colloquium: prevention, outstanding tools to evaluate risks and rehabilitation, a better responsibility of operators and memory keeping. (N.C.)

Assessment of sites concerning radioactive contamination during preparation of a Contamination Site Register; Bewertung der radiologischen Altlastenrelevanz von gewerblichen und industriellen Standorten

Energy Technology Data Exchange (ETDEWEB)

Gellermann, Rainer [Nuclear Control and Consulting GmbH, Braunschweig (Germany); Flesch, Klaus [Saechsisches Landesamt fuer Umwelt, Landwirtschaft und Geologie (LfULG), Dresden (Germany)

2014-07-01

Experience gained since 1990 in the new, but also old German Federal States has shown that there are radioactive contaminated sites beside the legacies of uranium mining in Germany which caused exposures exceeding the radiation protection limits for members of the public. The reason for this situation is that radioactivity has been excluded in the compilation of the register for potentially hazardous sites that are prepared routinely in the context of soil protection assessments. Moreover, the information contained in these registers is not yet evaluated regarding aspects of radioactivity. In many cases, the information existing at the soil protection authorities needs only to be additionally filtered in order to identify potentially hazardous sites for radioactive contamination. For that reason, the working group ''Natural radioactivity'' (AKNAT) of the German-Swiss Radiation Protection Association developed a specific catalogue of business branches that provides indications for radioactive legacies.

The improvement of Pilot-scale Electrokinetic for Radioactive Soil Decontamination

International Nuclear Information System (INIS)

Park, Hye Min; Kim, Gye Nam; Kim, Wan Suk; Moon, Jai Kwon

2012-01-01

Most nuclear facility sites have been contaminated by leakage of radioactive waste-solution due to corrosion of the waste-solution tanks and connection pipes by their long-term operation, set up around underground nuclear facilities. Therefore it was needed that the method to remediate a large volume of radioactive soil should be developed. Until now the soil washing method has studied to remediate soil contaminated with uranium, cobalt, cesium, and so on. But it has a lower removal efficiency of nuclide from soils and generated a large volume of waste-solution. And its application to the soil composed of fine particle is impossible. So, the electrokinetic method has been studied as a new technology for soil remediation recently. In this study, the original electrokinetic equipment of 50L suitable to soil contamination characteristics of Korean nuclear facility sites was manufactured for the remediation of soil contaminated with uranium. During experiment with the original electrokinetic equipment, many metal oxides were generated and were stuck on the cathod plate. Several methods to reduce the generation quantity of metal oxides in the electrokinetic equipment and to take off metal oxides from the cathod plate were improved. The soil with uranium was remediated with the improved electrokinetic equipment. The required time to remediate a radioactive soil to under a clearance concentration level was yielded through demonstration experiment with the improved electrokinetic equipment for its different radioactivity concentration

The improvement of Pilot-scale Electrokinetic for Radioactive Soil Decontamination

Energy Technology Data Exchange (ETDEWEB)

Park, Hye Min; Kim, Gye Nam; Kim, Wan Suk; Moon, Jai Kwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2012-05-15

Most nuclear facility sites have been contaminated by leakage of radioactive waste-solution due to corrosion of the waste-solution tanks and connection pipes by their long-term operation, set up around underground nuclear facilities. Therefore it was needed that the method to remediate a large volume of radioactive soil should be developed. Until now the soil washing method has studied to remediate soil contaminated with uranium, cobalt, cesium, and so on. But it has a lower removal efficiency of nuclide from soils and generated a large volume of waste-solution. And its application to the soil composed of fine particle is impossible. So, the electrokinetic method has been studied as a new technology for soil remediation recently. In this study, the original electrokinetic equipment of 50L suitable to soil contamination characteristics of Korean nuclear facility sites was manufactured for the remediation of soil contaminated with uranium. During experiment with the original electrokinetic equipment, many metal oxides were generated and were stuck on the cathod plate. Several methods to reduce the generation quantity of metal oxides in the electrokinetic equipment and to take off metal oxides from the cathod plate were improved. The soil with uranium was remediated with the improved electrokinetic equipment. The required time to remediate a radioactive soil to under a clearance concentration level was yielded through demonstration experiment with the improved electrokinetic equipment for its different radioactivity concentration

Software application for a total management of a radioactive facility

International Nuclear Information System (INIS)

Mirpuri, E.; Escudero, R.; Macias, M.T.; Perez, J.; Sanchez, A.; Usera, F.

2008-01-01

The use of radiological material and/or equipment that generate ionizing radiation is widely extended in biological research. In every laboratory there are a large variety of methods, operations, techniques, equipment, radioisotopes and users related to the work with ionizing radiation. In order to control the radioactive material, users and the whole facility a large number of documents, databases and information is necessary to be created by the manager of the Radioactivity Facility. This kind of information is characterized by a constant and persistent manipulation and includes information of great importance such as the general management of the radioactive material and waste management, exposed workers vigilance, controlled areas access, laboratory and equipment reservations, radiological inspections, etc. These activities are often complicated by the fact that the main manager of the radioactive facility is also in charge of bio-safety and working prevention issues so the documents to generate and manipulate and the procedures to develop are multiplied. A procedure to access and manage all these files is highly recommended in order to optimize the general management of the facility, avoiding loss of information, automating all the activities and allowing data necessary for control easily accessible. In this work we present a software application for a total management of the facility. This software has been developed by the collaboration of six of the most important research centers from Spain in coordination with the company 'Appize soluciones'. This is a flexible and versatile application that adapts to any specific need of every research center, providing the appropriate reports and checklist that speed up to general management and increase the ease of writing the official documents, including the Operations Book. (author)

Vitrification of radioactive contaminated soil by means of microwave energy

Science.gov (United States)

Yuan, Xun; Qing, Qi; Zhang, Shuai; Lu, Xirui

2017-03-01

Simulated radioactive contaminated soil was successfully vitrified by microwave sintering technology and the solidified body were systematically studied by Raman, XRD and SEM-EDX. The Raman results show that the solidified body transformed to amorphous structure better at higher temperature (1200 °C). The XRD results show that the metamictization has been significantly enhanced by the prolonged holding time at 1200 °C by microwave sintering, while by conventional sintering technology other crystal diffraction peaks, besides of silica at 2θ = 27.830°, still exist after being treated at 1200 °C for much longer time. The SEM-EDX discloses the micro-morphology of the sample and the uniform distribution of Nd element. All the results show that microwave technology performs vitrification better than the conventional sintering method in solidifying radioactive contaminated soil.

Dating of oilfield contamination by Natural Occurring Radioactive Materials (NORM) using isotopic ratios

International Nuclear Information System (INIS)

Al-Masri, M. S.; Othman, I.; Aba, A.

2008-05-01

In the present work, the possibility of using radium isotope ratios (226, 224, 228) for dating of NORM contaminated sites in the oilfields due to uncontrolled disposal of produced water into the environmental NORM contaminated soil sample were collected from different locations in Syrian Oilfields and radioactivity analysed. In addition, production water samples were collected and analysed to determine the isotopes ratios of the naturally occurring radioactive materials. The results have shown that the 228 Ra/ 226 Ra can be successfully used to date contaminated soil provided that this ratio is determined in production water. Moreover, the 210 Pb/ 226 Ra activity ratios was used for the first time for dating of contaminated soil where all factors affecting the method application have been evaluated. Furthermore, the obtained results for dating using the three methods were compared with the actual contamination dates provided by the oil companies. (Authors)

Air conditioner for radioactive material handling facility

International Nuclear Information System (INIS)

Tanaka, Takeaki.

1991-01-01

An air conditioner intakes open-air from an open-air intake port to remove sands and sea salt particles by air filters. Then, natural and artificial radioactive particles of less than 1 μm are removed by high performance particulate filters. After controlling the temperature by an air heater or an air cooler, air is sent to each of chambers in a facility under pressure elevation by a blower. In this case, glass fibers are used as the filter material for the high performance particulate filter, which has a performance of more than 99.97% for the particles of 0.3 μm grain size. Since this can sufficiently remove the natural radioactive materials intruded from the outside, a detection limit value in each of the chambers of the facility can be set 10 -13 to 10 -14 μci/cm 3 in respect of radiation control. Accordingly, radiation control can be conducted smoothly and appropriately. (I.N.)

Use of compensation and incentives in siting low-level radioactive waste disposal facilities

International Nuclear Information System (INIS)