10 CFR 36.35 - Source rack protection.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Source rack protection. 36.35 Section 36.35 Energy NUCLEAR... Requirements for Irradiators § 36.35 Source rack protection. If the product to be irradiated moves on a product conveyor system, the source rack and the mechanism that moves the rack must be protected by a barrier or...

Seismic analysis of freestanding fuel racks

International Nuclear Information System (INIS)

Gilmore, C.B.

1982-01-01

This paper presents a nonlinear transient dynamic time-history analysis of freestanding spent fuel storage racks subjected to seismic excitation. This type of storage rack is structurally unrestrained and submerged in water in the spent fuel pool of a nuclear power complex, holds (spent) fuel assemblies which have been removed from the reactor core. Nonlinearities in the fuel rack system include impact between the fuel assembly and surrounding cell due to clearances between them, friction due to sliding between the fuel rack support structure and spent fuel pool floor, and the lift-off of the fuel rack support structure from the spent fuel pool floor. The analysis of the fuel rack system includes impacting due to gap closures, energy losses due to impacting bodies, Coulomb damping between sliding surfaces, and hydrodynamic mass effects. Acceleration time history excitation development is discussed. Modeling considerations, such as the initial status of nonlinear elements, number of mode shapes to include in the analysis, modal damping, and integration time-step size are presented. The response of the fuel rack subjected to two-dimensional seismic excitation is analyzed by the modal superposition method, which has resulted in significant computer cost savings when compared to that of direct integration

40 CFR 63.1105 - Transfer racks.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Transfer racks. 63.1105 Section 63... Technology Standards § 63.1105 Transfer racks. (a) Design requirements. The owner or operator shall equip each transfer rack with one of the control options listed in paragraphs (a)(1) through (4) of this...

21 CFR 882.4215 - Clip rack.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Clip rack. 882.4215 Section 882.4215 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4215 Clip rack. (a) Identification. A clip rack is a...

Seismic analysis of spent nuclear fuel storage racks

International Nuclear Information System (INIS)

Shah, S.J.; Biddle, J.R.; Bennett, S.M.; Schechter, C.B.; Harstead, G.A.; Marquet, F.

1996-01-01

In many nuclear power plants, existing storage racks are being replaced with high-density racks to accommodate the increasing inventory of spent fuel. In the hypothetical design considered here, the high-density arrangement of fuel assemblies, or consolidated fuel canisters, is accomplished through the use of borated stainless steel (BSS) plates acting as neutron absorbers. No structural benefit from the BSS is assumed. This paper describes the methods used to perform seismic analysis of high density spent fuel storage racks. The sensitivity of important parameters such as the effect of variation of coefficients of friction between the rack legs and the pool floor and fuel loading conditions (consolidated and unconsolidated) are also discussed in the paper. Results of this study are presented. The high-density fuel racks are simply supported by the pool floor with no structural connections to adjacent racks or to the pool walls or floor. Therefore, the racks are free standing and may slide and tip. Several time history, nonlinear, seismic analyses are required to account for variations in the coefficient of friction, rack loading configuration, and the type of the seismic event. This paper presents several of the mathematical models usually used. Friction cannot be precisely predicted, so a range of friction coefficients is assumed. The range assumed for the analysis is 0.2 to 0.8. A detailed model representing a single rack is used to evaluate the 3-D loading effects. This model is a controlling case for the stress analysis. A 2-D multi-rack model representing a row of racks between the spent fuel pool walls is used to evaluate the change in gaps between racks. The racks are normally analyzed for the fuel loading conditions of consolidated, full, empty, and half-loaded with fuel assemblies

EXPRESS Rack Technology for Space Station

Science.gov (United States)

Davis, Ted B.; Adams, J. Brian; Fisher, Edward M., Jr.; Prickett, Guy B.; Smith, Timothy G.

1999-01-01

The EXPRESS rack provides accommodations for standard Mid-deck Locker and ISIS drawer payloads on the International Space Station. A design overview of the basic EXPRESS rack and two derivatives, the Human Research Facility and the Habitat Holding Rack, is given in Part I. In Part II, the design of the Solid State Power Control Module (SSPCM) is reviewed. The SSPCM is a programmable and remotely controllable power switching and voltage conversion unit which distributes and protects up to 3kW of 12OVDC and 28VDC power to payloads and rack subsystem components. Part III details the development and testing of a new data storage device, the BRP EXPRESS Memory Unit (BEMU). The BEMU is a conduction-cooled device which operates on 28VDC and is based on Boeing-modified 9GB commercial disk-drive technology. In Part IV results of a preliminary design effort for a rack Passive Damping System (PDS) are reported. The PDS is intended to isolate ISPR-based experiment racks from on-orbit vibration. System performance predictions based on component developmental testing indicate that such a system can provide effective isolation at frequencies of 1 Hz and above.

High density fuel storage rack

International Nuclear Information System (INIS)

Zezza, L.J.

1980-01-01

High storage density for spent nuclear fuel assemblies in a pool achieved by positioning fuel storage cells of high thermal neutron absorption materials in an upright configuration in a rack. The rack holds the cells at required pitch. Each cell carries an internal fuel assembly support, and most cells are vertically movable in the rack so that they rest on the pool bottom. Pool water circulation through the cells and around the fuel assemblies is permitted by circulation openings at the top and bottom of the cells above and below the fuel assemblies

Reusable Rack Interface Controller Common Software for Various Science Research Racks on the International Space Station

Science.gov (United States)

Lu, George C.

2003-01-01

The purpose of the EXPRESS (Expedite the PRocessing of Experiments to Space Station) rack project is to provide a set of predefined interfaces for scientific payloads which allow rapid integration into a payload rack on International Space Station (ISS). VxWorks' was selected as the operating system for the rack and payload resource controller, primarily based on the proliferation of VME (Versa Module Eurocard) products. These products provide needed flexibility for future hardware upgrades to meet everchanging science research rack configuration requirements. On the International Space Station, there are multiple science research rack configurations, including: 1) Human Research Facility (HRF); 2) EXPRESS ARIS (Active Rack Isolation System); 3) WORF (Window Observational Research Facility); and 4) HHR (Habitat Holding Rack). The RIC (Rack Interface Controller) connects payloads to the ISS bus architecture for data transfer between the payload and ground control. The RIC is a general purpose embedded computer which supports multiple communication protocols, including fiber optic communication buses, Ethernet buses, EIA-422, Mil-Std-1553 buses, SMPTE (Society Motion Picture Television Engineers)-170M video, and audio interfaces to payloads and the ISS. As a cost saving and software reliability strategy, the Boeing Payload Software Organization developed reusable common software where appropriate. These reusable modules included a set of low-level driver software interfaces to 1553B. RS232, RS422, Ethernet buses, HRDL (High Rate Data Link), video switch functionality, telemetry processing, and executive software hosted on the FUC computer. These drivers formed the basis for software development of the HRF, EXPRESS, EXPRESS ARIS, WORF, and HHR RIC executable modules. The reusable RIC common software has provided extensive benefits, including: 1) Significant reduction in development flow time; 2) Minimal rework and maintenance; 3) Improved reliability; and 4) Overall

Working safely with electronics racks

CERN Document Server

Simon Baird, HSE Unit Head

2016-01-01

Think of CERN and you’ll probably think of particle accelerators and detectors. These are the tools of the trade in particle physics, but behind them are the racks of electronics that include power supplies, control systems and data acquisition networks.   Inside an electronics rack: danger could be lurking if the rack is not powered off. In routine operation, these are no more harmful than the home entertainment system in your living room. But unscrew the cover and it’s a different matter. Even after following appropriate training, and with formal authorisation from your group leader or equivalent to carry out electrical work or any work in the vicinity of electrical hazards, and even with extensive experience of carrying out such operations, it’s important to incorporate safe working practices into your routine. At CERN, before the racks of electronics reach their operational configurations for the accelerators and detectors, they play a vital role in test set-ups ...

Seismic behavior of steel storage pallet racking systems

CERN Document Server

Castiglioni, Carlo Andrea

2016-01-01

This book presents the main outcomes of the first European research project on the seismic behavior of adjustable steel storage pallet racking systems. In particular, it describes a comprehensive and unique set of full-scale tests designed to assess such behavior. The tests performed include cyclic tests of full-scale rack components, namely beam-to-upright connections and column base connections; static and dynamic tests to assess the friction factor between pallets and rack beams; full-scale pushover and pseudodynamic tests of storage racks in down-aisle and cross-aisle directions; and full-scale dynamic tests on two-bay, three-level rack models. The implications of the findings of this extensive testing regime on the seismic behavior of racking systems are discussed in detail, highlighting e.g. the confirmation that under severe dynamic conditions “sliding” is the main factor influencing rack response. This work was conceived during the development of the SEISRACKS project. Its outcomes will contribute...

ACRR fuel storage racks criticality safety analysis

International Nuclear Information System (INIS)

Bodette, D.E.; Naegeli, R.E.

1997-10-01

This document presents the criticality safety analysis for a new fuel storage rack to support modification of the Annular Core Research Reactor for production of molybdenum-99 at Sandia National Laboratories, Technical Area V facilities. Criticality calculations with the MCNP code investigated various contingencies for the criticality control parameters. Important contingencies included mix of fuel element types stored, water density due to air bubbles or water level for the over-moderated racks, interaction with existing fuel storage racks and fuel storage holsters in the fuel storage pool, neutron absorption of planned rack design and materials, and criticality changes due to manufacturing tolerances or damage. Some limitations or restrictions on use of the new fuel storage rack for storage operations were developed through the criticality analysis and are required to meet the double contingency requirements of criticality safety. As shown in the analysis, this system will remain subcritical under all credible upset conditions. Administrative controls are necessary for loading, moving, and handling the storage rack as well as for control of operations around it. 21 refs., 16 figs., 4 tabs

Modular nuclear fuel assembly rack

International Nuclear Information System (INIS)

Davis, C.J.

1982-01-01

A modular nuclear fuel assembly rack constructed of an array of identical cells, each cell constructed of a plurality of identical flanged plates. The unique assembly of the plates into a rigid rack provides a cellular compartment for nuclear fuel assemblies and a cavity between the cells for accepting neutron absorbing materials thus allowing a closely spaced array. The modular rack size can be easily adapted to conform with available storage space. U-shaped flanges at the edges of the plates are nested together at the intersection of four cells in the array. A bar is placed at the intersection to lock the cells together

Fuel consumption impacts of auto roof racks

International Nuclear Information System (INIS)

Chen, Yuche; Meier, Alan

2016-01-01

The after-market roof rack is one of the most common components attached to a vehicle for carrying over-sized items, such as bicycles and skis. It is important to understand these racks’ fuel consumption impacts on both individual vehicles and the national fleet because they are widely used. We estimate the national fuel consumption impacts of roof racks using a bottom-up approach. Our model incorporates real-world data and vehicle stock information to enable assessing fuel consumption impacts for several categories of vehicles, rack configurations, and usage conditions. In addition, the model draws on two new data-gathering techniques, on-line forums and crowd-sourcing. The results show that nationwide, roof racks are responsible for 0.8‰ of light duty vehicle fuel consumption in 2015, corresponding to 100 million gallons of gasoline per year. Sensitivity analyses show that results are most sensitive to the fraction of vehicles with installed roof racks but carrying no equipment. The aerodynamic efficiency of typical roof racks can be greatly improved and reduce individual vehicle fuel consumption; however, government policies to minimize extensive driving with empty racks—if successful—could save more fuel nationally. - Highlights: •First estimate of national energy impacts of auto roof racks—about 1‰. •A bottom-up approach reveals details of the fuel consumption penalty caused by racks. •Two novel data collection techniques, on-line forums and crowd-sourcing, improve estimate. •Technical and behavioral policies could significantly cut fuel penalties from roof racks.

Solution structure of the human signaling protein RACK1

Directory of Open Access Journals (Sweden)

Papa Priscila F

2010-06-01

Full Text Available Abstract Background The adaptor protein RACK1 (receptor of activated kinase 1 was originally identified as an anchoring protein for protein kinase C. RACK1 is a 36 kDa protein, and is composed of seven WD repeats which mediate its protein-protein interactions. RACK1 is ubiquitously expressed and has been implicated in diverse cellular processes involving: protein translation regulation, neuropathological processes, cellular stress, and tissue development. Results In this study we performed a biophysical analysis of human RACK1 with the aim of obtaining low resolution structural information. Small angle X-ray scattering (SAXS experiments demonstrated that human RACK1 is globular and monomeric in solution and its low resolution structure is strikingly similar to that of an homology model previously calculated by us and to the crystallographic structure of RACK1 isoform A from Arabidopsis thaliana. Both sedimentation velocity and sedimentation equilibrium analytical ultracentrifugation techniques showed that RACK1 is predominantly a monomer of around 37 kDa in solution, but also presents small amounts of oligomeric species. Moreover, hydrodynamic data suggested that RACK1 has a slightly asymmetric shape. The interaction of RACK1 and Ki-1/57 was tested by sedimentation equilibrium. The results suggested that the association between RACK1 and Ki-1/57(122-413 follows a stoichiometry of 1:1. The binding constant (KB observed for RACK1-Ki-1/57(122-413 interaction was of around (1.5 ± 0.2 × 106 M-1 and resulted in a dissociation constant (KD of (0.7 ± 0.1 × 10-6 M. Moreover, the fluorescence data also suggests that the interaction may occur in a cooperative fashion. Conclusion Our SAXS and analytical ultracentrifugation experiments indicated that RACK1 is predominantly a monomer in solution. RACK1 and Ki-1/57(122-413 interact strongly under the tested conditions.

RackSaver neutron absorbing device development and testing

International Nuclear Information System (INIS)

Lambert, R.; O'Leary, P.; Roberts, P.

1996-01-01

Siemens Power Corporation (SPC), in cooperation with the Electric Power Research Institute (EPRI), has developed the RackSaver neutron absorbing insert. The RackSaver insert can be installed onto spent nuclear fuel assemblies to replace deteriorating Boraflex neutron absorbing material installed in some spent-fuel storage racks. This paper describes results of a development and in-pool demonstration program performed to support potential utilization of the RackSaver neutron absorbing insert by affected utilities. The program objective was to advance the RackSaver concept into a field-demonstrated product. This objective was accomplished through three phases: design, licensing and criticality evaluations, and demonstration testing

Compact fuel storage rack for fuel pools

International Nuclear Information System (INIS)

Parras, F.; Louvat, J.P.

1986-01-01

ETS LEMER and FRAMATOME propose a new compact storage rack. This rack permits a considerable increase of the storage capacity of cooling pools. A short description of the structure and the components is presented, to propose racks that are: . Inalterable, . Compact, . Insensitive to earthquakes. Installation in pools already in operation is simplified by their light structure and the bearing device [fr

From racks to pointed Hopf algebras

OpenAIRE

Andruskiewitsch, Nicolás; Graña, Matı́as

2003-01-01

A fundamental step in the classification of finite-dimensional complex pointed Hopf algebras is the determination of all finite-dimensional Nichols algebras of braided vector spaces arising from groups. The most important class of braided vector spaces arising from groups is the class of braided vector spaces (CX, c^q), where C is the field of complex numbers, X is a rack and q is a 2-cocycle on X with values in C^*. Racks and cohomology of racks appeared also in the work of topologists. This...

Spent fuel storage rack for atomic power plant

International Nuclear Information System (INIS)

Kodama, Tatemitsu.

1981-01-01

Purpose: To flexibly cope with the changes in the size and shape of spent fuel storage containers by placing a number of independently-constructed rack cells in a rack frame in such a manner that the guide support members of the storage rack, mounted on each rack cell may be replaced. Constitution: Independently-constructed rack cells are inserted from above into a rack frame rigidly installed on the bottom of a water pool. Each cell is produced by welding, has a handling head mounted at the top, and guide support members made of three replaceable guide tubes are mounted with bolts. If the size and the shape of the containers are altered, this configuration can easily cope with the new container shape by merely having the guide tubes replaced, without adversely affecting other cells and without necessitating draining of the water in the pool. (Yoshino, Y.)

RACK1, A Multifaceted Scaffolding Protein: Structure and Function

LENUS (Irish Health Repository)

Adams, David R

2011-10-06

Abstract The Receptor for Activated C Kinase 1 (RACK1) is a member of the tryptophan-aspartate repeat (WD-repeat) family of proteins and shares significant homology to the β subunit of G-proteins (Gβ). RACK1 adopts a seven-bladed β-propeller structure which facilitates protein binding. RACK1 has a significant role to play in shuttling proteins around the cell, anchoring proteins at particular locations and in stabilising protein activity. It interacts with the ribosomal machinery, with several cell surface receptors and with proteins in the nucleus. As a result, RACK1 is a key mediator of various pathways and contributes to numerous aspects of cellular function. Here, we discuss RACK1 gene and structure and its role in specific signaling pathways, and address how posttranslational modifications facilitate subcellular location and translocation of RACK1. This review condenses several recent studies suggesting a role for RACK1 in physiological processes such as development, cell migration, central nervous system (CN) function and circadian rhythm as well as reviewing the role of RACK1 in disease.

Server rack for improved data center management

Science.gov (United States)

Bermudez Rodriguez, Sergio A.; Hamann, Hendrik F.; Wehle, Hans-Dieter

2018-01-09

Methods and systems for data center management include collecting sensor data from one or more sensors in a rack; determining a location and identifying information for each asset in the rack using a set of asset tags associated with respective assets; communicating the sensor and asset location to a communication module; receiving an instruction from the communication module; and executing the received instruction to change a property of the rack.

Framatome offers new high density Cadminox racks

International Nuclear Information System (INIS)

Anon.

1985-01-01

Framatome have developed a new material called Cadminox for use in high density spent fuel storage racks. It is claimed that Cadminox will remain stable stable in pond storage when racks submerged in boronated water are irradiated by the spent fuel they contain. A brief description of the storage module is given, including the aseismic bearing device which minimises loads on pond walls, racks and fuel assemblies. (UK)

40 CFR 63.650 - Gasoline loading rack provisions.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Gasoline loading rack provisions. 63... loading rack provisions. (a) Except as provided in paragraphs (b) through (c) of this section, each owner or operator of a Group 1 gasoline loading rack classified under Standard Industrial Classification...

Rack assembly for mounting solar modules

Science.gov (United States)

Plaisted, Joshua Reed; West, Brian

2010-12-28

A rack assembly is provided for mounting solar modules over an underlying body. The rack assembly may include a plurality of rail structures that are arrangeable over the underlying body to form an overall perimeter for the rack assembly. One or more retention structures may be provided with the plurality of rail structures, where each retention structure is configured to support one or more solar modules at a given height above the underlying body. At least some of the plurality of rail structures are adapted to enable individual rail structures o be sealed over the underlying body so as to constrain air flow underneath the solar modules. Additionally, at least one of (i) one or more of the rail structures, or (ii) the one or more retention structures are adjustable so as to adapt the rack assembly to accommodate solar modules of varying forms or dimensions.

Anne-Ly Võlli: Iga inimene ja asutus vajab omamoodi lähenemist / Anne-Ly Võlli ; intervjueerinud Jaanika Kressa

Index Scriptorium Estoniae

Võlli, Anne-Ly, 1976-

2009-01-01

MTÜ Jõgevamaa Omavalitsuste Aktiviseerimiskeskus kinnitas avaliku konkursi tulemusel juhatuse liikmeks Anne-Ly Võlli, kelle ülesandeks on keskuse tegevuse juhtimine ja koostöö arendamine partneromavalitsuste ja teiste koostööpartnerite vahel

Refurbishment of the Oregon State University rotating rack

International Nuclear Information System (INIS)

Higginbotham, J.F.

1991-01-01

TRIGA reactors have experienced operational difficulties with the rotating racks used for sample irradiation. The most common problem occurs when the rack seizes, and the corrective action taken is replacement of the rack assembly. This paper describes the symptoms leading to rack failure and a refurbishment procedure to correct the problem without replacing the rack at the Oregon State University TRIGA Reactor (OSTR) Facility. This procedure was accomplished with extraordinary results from an operational and a radiation protection standpoint. The refurbishment has extended the useful life of this reactor facility with minimal financial impact. Given the declining number of university-based research reactors, it is in the nation's best interest to maintain the currently operating research reactor facilities, and the described procedure can aid in achieving that goal

RACK(1) to the future - a historical perspective

LENUS (Irish Health Repository)

Ron, Dorit

2013-08-01

This perspective summarises the first and long overdue RACK1 meeting held at the University of Limerick, Ireland, May 2013, in which RACK1’s role in the immune system, the heart and the brain were discussed and its contribution to disease states such as cancer, cardiac hypertrophy and addiction were described. RACK1 is a scaffolding protein and a member of the WD repeat family of proteins. These proteins have a unique architectural assembly that facilitates protein anchoring and the stabilisation of protein activity. A large body of evidence is accumulating which is helping to define the versatile role of RACK1 in assembling and dismantling complex signaling pathways from the cell membrane to the nucleus in health and disease. In this commentary, we first provide a historical perspective on RACK1. We also address many of the pertinent and topical questions about this protein such as its role in transcription, epigenetics and translation, its cytoskeletal contribution and the merits of targeting RACK1 in disease.

RACK1-mediated translation control promotes liver fibrogenesis

Energy Technology Data Exchange (ETDEWEB)

Liu, Min; Peng, Peike; Wang, Jiajun [Department of Biochemistry and Molecular Biology, School of Basic Medical Sciences, Fudan University, Shanghai 200032 (China); Wang, Lan; Duan, Fangfang [Institute of Biomedical Science, Fudan University, Shanghai 200032 (China); Jia, Dongwei, E-mail: jiadongwei@fudan.edu.cn [Department of Biochemistry and Molecular Biology, School of Basic Medical Sciences, Fudan University, Shanghai 200032 (China); Ruan, Yuanyuan, E-mail: yuanyuanruan@fudan.edu.cn [Department of Biochemistry and Molecular Biology, School of Basic Medical Sciences, Fudan University, Shanghai 200032 (China); Gu, Jianxin [Department of Biochemistry and Molecular Biology, School of Basic Medical Sciences, Fudan University, Shanghai 200032 (China); Institute of Biomedical Science, Fudan University, Shanghai 200032 (China)

2015-07-31

Activation of quiescent hepatic stellate cells (HSCs) is the central event of liver fibrosis. The translational machinery is an optimized molecular network that affects cellular homoeostasis and diseases, whereas the role of protein translation in HSCs activation and liver fibrosis is little defined. Our previous report suggests that up-regulation of receptor for activated C-kinase 1(RACK1) in HSCs is critical for liver fibrogenesis. In this study, we found that RACK1 promoted macrophage conditioned medium (MCM)-induced assembly of eIF4F and phosphorylation of eIF4E in primary HSCs. RACK1 enhanced the translation and expression of pro-fibrogenic factors collagen 1α1, snail and cyclin E1 induced by MCM. Administration of PP242 or knock-down of eIF4E suppressed RACK1-stimulated collagen 1α1 production, proliferation and migration in primary HSCs. In addition, depletion of eIF4E attenuated thioacetamide (TAA)-induced liver fibrosis in vivo. Our data suggest that RACK1-mediated stimulation of cap-dependent translation plays crucial roles in HSCs activation and liver fibrogenesis, and targeting translation initiation could be a promising strategy for the treatment of liver fibrosis. - Highlights: • RACK1 induces the assembly of eIF4F and phosphorylation of eIF4E in primary HSCs. • RACK1 stimulates the translation of collagen 1α1, snail and cyclin E1 in HSCs. • RACK1 promotes HSCs activation via cap-mediated translation. • Depletion of eIF4E suppresses liver fibrogenesis in vivo.

RACK1-mediated translation control promotes liver fibrogenesis

International Nuclear Information System (INIS)

Liu, Min; Peng, Peike; Wang, Jiajun; Wang, Lan; Duan, Fangfang; Jia, Dongwei; Ruan, Yuanyuan; Gu, Jianxin

2015-01-01

Activation of quiescent hepatic stellate cells (HSCs) is the central event of liver fibrosis. The translational machinery is an optimized molecular network that affects cellular homoeostasis and diseases, whereas the role of protein translation in HSCs activation and liver fibrosis is little defined. Our previous report suggests that up-regulation of receptor for activated C-kinase 1(RACK1) in HSCs is critical for liver fibrogenesis. In this study, we found that RACK1 promoted macrophage conditioned medium (MCM)-induced assembly of eIF4F and phosphorylation of eIF4E in primary HSCs. RACK1 enhanced the translation and expression of pro-fibrogenic factors collagen 1α1, snail and cyclin E1 induced by MCM. Administration of PP242 or knock-down of eIF4E suppressed RACK1-stimulated collagen 1α1 production, proliferation and migration in primary HSCs. In addition, depletion of eIF4E attenuated thioacetamide (TAA)-induced liver fibrosis in vivo. Our data suggest that RACK1-mediated stimulation of cap-dependent translation plays crucial roles in HSCs activation and liver fibrogenesis, and targeting translation initiation could be a promising strategy for the treatment of liver fibrosis. - Highlights: • RACK1 induces the assembly of eIF4F and phosphorylation of eIF4E in primary HSCs. • RACK1 stimulates the translation of collagen 1α1, snail and cyclin E1 in HSCs. • RACK1 promotes HSCs activation via cap-mediated translation. • Depletion of eIF4E suppresses liver fibrogenesis in vivo

Microgravity Disturbance Predictions in the Combustion Integrated Rack

Science.gov (United States)

Just, M.; Grodsinsky, Carlos M.

2002-01-01

This paper will focus on the approach used to characterize microgravity disturbances in the Combustion Integrated Rack (CIR), currently scheduled for launch to the International Space Station (ISS) in 2005. Microgravity experiments contained within the CIR are extremely sensitive to vibratory and transient disturbances originating on-board and off-board the rack. Therefore, several techniques are implemented to isolate the critical science locations from external vibration. A combined testing and analysis approach is utilized to predict the resulting microgravity levels at the critical science location. The major topics to be addressed are: 1) CIR Vibration Isolation Approaches, 2) Disturbance Sources and Characterization, 3) Microgravity Predictive Modeling, 4) Science Microgravity Requirements, 6) Microgravity Control, and 7) On-Orbit Disturbance Measurement. The CIR is using the Passive Rack Isolation System (PaRIS) to isolate the rack from offboard rack disturbances. By utilizing this system, CIR is connected to the U.S. Lab module structure by either 13 or 14 umbilical lines and 8 spring / damper isolators. Some on-board CIR disturbers are locally isolated by grommets or wire ropes. CIR's environmental and science on board support equipment such as air circulation fans, pumps, water flow, air flow, solenoid valves, and computer hard drives cause disturbances within the rack. These disturbers along with the rack structure must be characterized to predict whether the on-orbit vibration levels during experimentation exceed the specified science microgravity vibration level requirements. Both vibratory and transient disturbance conditions are addressed. Disturbance levels/analytical inputs are obtained for each individual disturber in a "free floating" condition in the Glenn Research Center (GRC) Microgravity Emissions Lab (MEL). Flight spare hardware is tested on an Orbital Replacement Unit (ORU) basis. Based on test and analysis, maximum disturbance level

Seismic and structural analysis of high density/consolidated spent fuel storage racks

International Nuclear Information System (INIS)

Shah, S.J.; Biddle, J.R.; Bennett, S.M.; Schechter, C.B.; Harstead, G.A.; Kopecky, B.

1995-01-01

In many nuclear power plants, existing storage racks are being replaced with high-density racks to accommodate the increasing inventory of spent fuel. In the hypothetical design considered here, the high-density arrangement of fuel assemblies, or consolidated fuel canisters, is accomplished through the use of borated stainless steel (BSS) plates acting as neutron absorbers. The high-density fuel racks are simply supported by the pool floor with no structural connections to adjacent racks or to the pool walls or floor. Therefore, the racks are free standing and may slide and tip. Several time history, nonlinear, seismic analyses are required to account for variations in the coefficient of friction, rack loading configuration, ad the type of the seismic event. This paper presents several of the mathematical models usually used. The models include features to allow sliding and tipping of the racks and to represent the hydrodynamic coupling which can occur between fuel assemblies and rack cells, between adjacent racks, and between the racks and the reinforced concrete walls. A detailed model representing a single rack is used to evaluate the 3-D loading effects. This model is a controlling case for the stress analysis. A 2-D multi-rack model representing a row of racks between the spent fuel pool walls is used to evaluate the change in gaps between racks. The racks are analyzed for the fuel loading conditions of consolidated, full, empty, and half-loaded with fuel assemblies

Seismic analysis of rack structures for fuel cycle facilities

International Nuclear Information System (INIS)

Mochio, Takashi; Morooka, Akihiko; Ito, Takashi.

1987-01-01

A concept of remote maintenance using in large remote cell and rack system structure, which is now under development at high active liquid waste vitrification facility of PNC and West Germany reprocessing plant WA-350, has been adopted to reduce the radiation exposure and increase the operating efficiency. The operation of a highly efficient remote maintenance system sometimes requires the rack structures to be fairly flexible, because of the large number of loose connections and/or gapped supports and the low number of rack frames. This means that there is a possibility of severe damage occurring due to large amplitude responses during a strong earthquake. Therefore, it is very important to estimate the earthquake-resistance capacity of rack structures, including process equipment, to earthquake excitation. This paper presents an outline of a new computer code ''FRACK'' to analyze the nonlinear seismic response of a rack structure developed as a first stage in the rack system seismic research program. (author)

Storage rack for fuel cell receiving shrouds

International Nuclear Information System (INIS)

Mollon, L.

1978-01-01

Disclosed is a rack for receiving a multiplicity of vertical tubular shrouds or tubes for storing spent nuclear fuel cells. The rack comprises a plurality of horizontally reticulated frames interconnected by tension rods and spacing tubes surrounding the rods

Manufacturing and Construction of Spent Fuel Storage Rack for Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Lee, Sangjin; Jung, Kwangsub; Oh, Jinho; Lee, Jongmin [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The spent fuel storage rack consists of spent fuel storage racks and support frame. The spent fuel storage racks are installed in the support frame. A spent fuel storage rack consists of frame weldment and storage cell pipe assembly. Storage cell pipe assembly is mounted on the base plate of the frame weldment. The spent fuel storage rack is designed to withstand seismic load and other loads during earthquake. The structural integrity of the spent fuel storage rack is evaluated in accordance with ASME Section III, Subsection NF. Computer Code used for this analysis is ANSYS version 14.0.0. Dead load and seismic load is considered in load condition and hydrodynamic mass is included in the analysis. Design, manufacturing, and construction of the spent fuel storage rack are introduced. The spent fuel storage rack is for storage of spent fuel assemblies. The spent fuel storage rack should be designed, manufactured, and installed with consideration of predicted number of spent fuel assemblies, structural integrity, resistivity to corrosion and radiation, cleaning, and workability.

O-GlcNAcylation of RACK1 promotes hepatocellular carcinogenesis.

Science.gov (United States)

Duan, Fangfang; Wu, Hao; Jia, Dongwei; Wu, Weicheng; Ren, Shifang; Wang, Lan; Song, Shushu; Guo, Xinying; Liu, Fenglin; Ruan, Yuanyuan; Gu, Jianxin

2018-06-01

Aberrant oncogenic mRNA translation and protein O-linked β-N-acetylglucosaminylation (O-GlcNAcylation) are general features during tumorigenesis. Nevertheless, whether and how these two pathways are interlinked remain unknown. Our previous study indicated that ribosomal receptor for activated C-kinase 1 (RACK1) promoted chemoresistance and growth in hepatocellular carcinoma (HCC). The aim of this study is to examine the role of RACK1 O-GlcNAcylation in oncogene translation and HCC carcinogenesis. The site(s) of RACK1 for O-GlcNAcylation was mapped by mass spectrometry analysis. HCC cell lines were employed to examine the effects of RACK1 O-GlcNAcylation on the translation of oncogenic factors and behaviors of tumor cells in vitro. Transgenic knock-in mice were used to detect the role of RACK1 O-GlcNAcylation in modulating HCC tumorigenesis in vivo. The correlation of RACK1 O-GlcNAcylation with tumor progression and relapse were analyzed in clinical HCC samples. We found that ribosomal RACK1 was highly modified by O-GlcNAc at Ser122. O-GlcNAcylation of RACK1 enhanced its protein stability, ribosome binding and interaction with PKCβII (PRKCB), leading to increased eukaryotic translation initiation factor 4E phosphorylation and translation of potent oncogenes in HCC cells. Genetic ablation of RACK1 O-GlcNAcylation at Ser122 dramatically suppressed tumorigenesis, angiogenesis, and metastasis in vitro and in diethylnitrosamine (DEN)-induced HCC mouse model. Increased RACK1 O-GlcNAcylation was also observed in HCC patient samples and correlated with tumor development and recurrence after chemotherapy. These findings demonstrate that RACK1 acts as key mediator linking O-GlcNAc metabolism to cap-dependent translation during HCC tumorigenesis. Targeting RACK1 O-GlcNAcylation provides promising options for HCC treatment. O-GlcNAcylation of ribosomal receptor for activated C-kinase 1 at the amino acid serine122 promotes its stability, ribosome localization and interaction

30 CFR 57.7050 - Tool and drill steel racks.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tool and drill steel racks. 57.7050 Section 57... Rotary Jet Piercing Drilling-Surface and Underground § 57.7050 Tool and drill steel racks. Receptacles or racks shall be provided for drill steel and tools stored or carried on drills. ...

Materials Science Research Rack-1 Fire Suppressant Distribution Test Report

Science.gov (United States)

Wieland, P. O.

2002-01-01

Fire suppressant distribution testing was performed on the Materials Science Research Rack-1 (MSRR-1), a furnace facility payload that will be installed in the U.S. Lab module of the International Space Station. Unlike racks that were tested previously, the MSRR-1 uses the Active Rack Isolation System (ARIS) to reduce vibration on experiments, so the effects of ARIS on fire suppressant distribution were unknown. Two tests were performed to map the distribution of CO2 fire suppressant throughout a mockup of the MSRR-1 designed to have the same component volumes and flowpath restrictions as the flight rack. For the first test, the average maximum CO2 concentration for the rack was 60 percent, achieved within 45 s of discharge initiation, meeting the requirement to reach 50 percent throughout the rack within 1 min. For the second test, one of the experiment mockups was removed to provide a worst-case configuration, and the average maximum CO2 concentration for the rack was 58 percent. Comparing the results of this testing with results from previous testing leads to several general conclusions that can be used to evaluate future racks. The MSRR-1 will meet the requirements for fire suppressant distribution. Primary factors that affect the ability to meet the CO2 distribution requirements are the free air volume in the rack and the total area and distribution of openings in the rack shell. The length of the suppressant flowpath and degree of tortuousness has little correlation with CO2 concentration. The total area of holes in the rack shell could be significantly increased. The free air volume could be significantly increased. To ensure the highest maximum CO2 concentration, the PFE nozzle should be inserted to the stop on the nozzle.

Knot invariants derived from quandles and racks

OpenAIRE

Kamada, Seiichi

2002-01-01

The homology and cohomology of quandles and racks are used in knot theory: given a finite quandle and a cocycle, we can construct a knot invariant. This is a quick introductory survey to the invariants of knots derived from quandles and racks.

An embedded acceleration measurement capability for EXPRESS Rack Payloads

International Nuclear Information System (INIS)

Foster, William M. II; Sutliff, Thomas J.

2000-01-01

The International Space Station provides a microgravity environment allowing long duration studies to be made on phenomena masked by the presence of earth's gravitational effects. Studies are also enabled in areas requiring a substantial decrease in steady-state and vibratory acceleration environments. In anticipation microgravity science experiments being targeted for EXPRESS (EXpedite the PRocessing of Experiments to Space Station) Racks, a capability has been provided to simplify and conduct a consistent measurement of the microgravity environment for payloads. The Space Acceleration Measurement System-II (SAMS-II) project has collaborated with the EXPRESS Rack Project to embed an electronics unit within the four EXPRESS Racks equipped with Active Rack Isolation Systems (ARIS). Each SAMS-II unit provides a standardized means for payload acceleration measurements to be acquired. Access to this capability is via front panel connections similar to those of power, data and water cooling provided for EXPRESS payloads. Furthermore, an International Subrack Interface Standard (ISIS) drawer configuration has been developed to provide measurement capability to the non-ARIS equipped EXPRESS Racks, as well as to other ISIS-configured racks, for non-isolated experimental measurement needs. This paper describes the SAMS-II acceleration measurement capabilities provided to ISS users and, in particular, to the EXPRESS Rack community

30 CFR 56.7050 - Tool and drill steel racks.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Tool and drill steel racks. 56.7050 Section 56.7050 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Jet Piercing Drilling § 56.7050 Tool and drill steel racks. Receptacles or racks shall be provided for...

AP Alternatives Modular Solar Racking

OpenAIRE

ECT Team, Purdue

2015-01-01

Solar panels have been used to generate and supply electricity in various applications such as residential and commercial buildings. Therefore, a need for a quicker approach to installation as well as the need to reduce workmanship to speed up the process is needed. Solar racks are developed through the use of automated equipment to “preassemble the racking hardware, pre-install the solar modules, and drive helical anchors into the ground rapidly”. So instead of installing one panel at a time...

Fabrication of the Spent Fuel Elements Rack on the ISFSF

International Nuclear Information System (INIS)

Slamet Wiranto; Sigit Purwanto; Safrul, H.

2004-01-01

The Interim Storage For Spent Fuel elements (ISFSF) was designed to be able to store the 33 spent fuel element racks with capacity of 1386 of normal spent fuel elements and 2 racks for 36 of defected ones. Until now, only 9 out of 33 racks of normal spent fuel elements and lout of 2 racks of defected fuel elements are available. Five of them have suffered from corrosion so that they are not fulfilled the requirements of the spent fuel elements storage anymore. Meanwhile, the spent fuel storage racks in the reactor are almost full. It means, the transfer of the spent fuel from reactor spent fuel storage to the ISFSF pool are compulsory needed. Therefore, it is necessary to provide the new ISFSF spent fuel storage rack with better material and fabrication method than the old one. In this design all materials consist of SS 316 L that are welded with the Argon TIG-welding. Right now there has been one new spent fuel storage rack fabricated with capacity of 42 normal spent fuel elements. (author)

Conducting Research on the International Space Station using the EXPRESS Rack Facilities

Science.gov (United States)

Thompson, Sean W.; Lake, Robert E.

2016-01-01

Eight "Expedite the Processing of Experiments to Space Station" (EXPRESS) Rack facilities are located within the International Space Station (ISS) laboratories to provide standard resources and interfaces for the simultaneous and independent operation of multiple experiments within each rack. Each EXPRESS Rack provides eight Middeck Locker Equivalent locations and two drawer locations for powered experiment equipment, also referred to as sub-rack payloads. Payload developers may provide their own structure to occupy the equivalent volume of one, two, or four lockers as a single unit. Resources provided for each location include power (28 Vdc, 0-500 W), command and data handling (Ethernet, RS-422, 5 Vdc discrete, +/- 5 Vdc analog), video (NTSC/RS 170A), and air cooling (0-200 W). Each rack also provides water cooling for two locations (500W ea.), one vacuum exhaust interface, and one gaseous nitrogen interface. Standard interfacing cables and hoses are provided on-orbit. One laptop computer is provided with each rack to control the rack and to accommodate payload application software. Four of the racks are equipped with the Active Rack Isolation System to reduce vibration between the ISS and the rack. EXPRESS Racks are operated by the Payload Operations Integration Center at Marshall Space Flight Center and the sub-rack experiments are operated remotely by the investigating organization. Payload Integration Managers serve as a focal to assist organizations developing payloads for an EXPRESS Rack. NASA provides EXPRESS Rack simulator software for payload developers to checkout payload command and data handling at the development site before integrating the payload with the EXPRESS Functional Checkout Unit for an end-to-end test before flight. EXPRESS Racks began supporting investigations onboard ISS on April 24, 2001 and will continue through the life of the ISS.

Experimental motion behavior of submerged fuel racks

International Nuclear Information System (INIS)

Ellingson, F.J.; Wachter, W.; Moscardini, R.L.

1989-01-01

The design of submerged nuclear storage racks for light water reactor nuclear fuel has undergone a change from fixed position to a free-standing arrangement. Seismic analysis of the motion of the free-standing racks requires three-dimensional computer modeling that uses past studies of hydrodynamic mass and hydraulic coupling for rigid flat plates. This paper describes the results of experiments that show a reduced value for hydrodynamic mass and coupling forces when flexible elements are involved. To support this work, experiments were run with two full-scale welded box sections submerged in a water tank. The preliminary results indicate reduction in hydrodynamic mass due to box wall flexibility, a lack of impacting of box wall to box wall over the entire frequency range, and large hydrodynamic coupling forces under all test conditions. It is hypothesized that the coupling forces are sufficiently strong to prevent rotational motion of one rack when surrounded by adjacent racks

Thermal Analysis Evaluation of Spent Fuel Storage Rack for Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Lee, Sangjin; Oh, Jinho; Kwak, Jinsung; Lee, Jongmin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

Spent fuel storage rack is to store spent fuel assemblies. The spent fuel storage rack is submerged in the designated pool for cooling. Due to the condition change of the pool water, the effect of thermal load on spent fuel storage rack must be analyzed and evaluated. In this paper, thermal stress analysis is performed and evaluated on a spent fuel storage rack. For thermal stress evaluation of the spent fuel storage rack, load combinations and allowable criteria in ASME Sec. III NB-3220 are applied. In cases of A-1 and B-1, the same temperature applied on the whole model, thermal stress doesn't occur because there is no constraint about the thermal expansion. The support frame is located on the pool bottom in free standing type and the racks are located in the support frame with enough space. Thermal expansion was considered and reflected in the design of spent fuel storage rack in advance. Thermal stress analysis is performed and evaluated on a spent fuel storage rack with consideration of pool water temperature variation. The thermal analysis including a linear heat transfer and the thermal stress analysis is performed for the racks and support frame and resulted stresses are within allowable criteria.

Decreased Blastocyst Production in Mice Exposed to Increased Rack Noise

Science.gov (United States)

Zamora, Bernadette M; Jiang, Meisheng; Wang, Ying; Chai, Minghua; Lawson, P Timothy; Lawson, Gregory W

2009-01-01

This study was conducted to investigate the possible effect of rack type on the blastocyst yield of mouse embryo donors. The first phase of the study consisted of housing some mice (group A) in a ventilated rack and others (group B) in a static rack in the same room for 3 d, followed by euthanasia for blastocyst collection and corticosterone assay. Parametric tests were used to compare groups. The number of blastocysts per donor was lower in group A (5.0 ± 1.4 blastocysts) than group B (13.1 ± 3.7 blastocysts). Mean noise was higher in the ventilated rack (80.4 dBC) than in the static rack (69.2 dBC). Serum corticosterone concentrations did not differ between groups. For the second phase of the study, a third group of mice (group C) was housed in a static rack without a ventilated rack in the same room. The noise level for group C was even lower (45.18 ± 2.91 dBC), and the blastocyst count per donor (16.4 ± 2.4) was higher than that of group B. The mean noise levels of empty ventilated and static racks differed significantly between groups for 10 different sound frequencies. Plotting mean blastocyst production against mean rack noise revealed a negative linear relationship with good strength of correlation. These results support the earlier observation that decreased blastocyst count occurs following housing of bred C57BL/6 donor mice in ventilated cages. PMID:19807968

High density aseismic spent fuel storage racks

International Nuclear Information System (INIS)

Louvat, J.P.

1985-05-01

After the reasons of the development of high density aseismic spent fuel racks by FRAMATOME and LEMER, a description is presented, as also the codes, standards and regulations used to design this FRAMATOME storage rack. Tests have been carried out concerning criticality, irradiation of Cadminox, corrosion of the cell, and the seismic behaviour

Innovative Ballasted Flat Roof Solar PV Racking System

Energy Technology Data Exchange (ETDEWEB)

Peek, Richard T. [Cascade Engineering, Grand Rapids, MI (United States)

2014-12-15

The objective of this project was to reduce the cost of racking for PV solar on flat commercial rooftops. Cost reductions would come from both labor savings and material savings related to the installation process. The rack would need to accommodate the majority of modules available on the market. Cascade Engineering has a long history of converting traditional metal type applications over to plastic. Injection molding of plastics have numerous advantages including selection of resin for the application, placing the material exactly where it is needed, designing in features that will speed up the installation process, and weight reduction of the array. A plastic rack would need to meet the requirements of UL2703, Mounting systems, mounting devices, clamping/retention devices, and ground lugs for use with flat-plate photovoltaic modules and panels. Comparing original data to the end of project racking design, racking material costs were reduced 50% and labor costs reduced 64%. The racking product accommodates all 60 and 72 cell panels on the market, meets UL2703 requirements, contributes only 1.3 pounds per square foot of weight to the array, requires little ballast to secure the array, automatically grounds the module when the module is secured, stacks/nests well for shipping/fewer lifts to the roof, provides integrated wire routing, allows water to drain on the roof, and accommodates various seismic roof connections. Project goals were achieved as noted in the original funding application.

Nonlinear dynamics of a rack-pinion-rack device powered by the Casimir force.

Science.gov (United States)

Miri, MirFaez; Nekouie, Vahid; Golestanian, Ramin

2010-01-01

Using the lateral Casimir force-a manifestation of the quantum fluctuations of the electromagnetic field between objects with corrugated surfaces-as the main force transduction mechanism, a nanomechanical device with rich dynamical behaviors is proposed. The device is made of two parallel racks that are moving in the same direction and a pinion in the middle that couples with both racks via the noncontact lateral Casimir force. The built-in frustration in the device causes it to be very sensitive and react dramatically to minute changes in the geometrical parameters and initial conditions of the system. The noncontact nature of the proposed device could help with the ubiquitous wear problem in nanoscale mechanical systems.

iAnn

DEFF Research Database (Denmark)

Jimenez, Rafael C; Albar, Juan P; Bhak, Jong

2013-01-01

We present iAnn, an open source community-driven platform for dissemination of life science events, such as courses, conferences and workshops. iAnn allows automatic visualisation and integration of customised event reports. A central repository lies at the core of the platform: curators add...... submitted events, and these are subsequently accessed via web services. Thus, once an iAnn widget is incorporated into a website, it permanently shows timely relevant information as if it were native to the remote site. At the same time, announcements submitted to the repository are automatically...

Furniture Rack Corrosion Coupon Surveillance - 2012 Update

International Nuclear Information System (INIS)

Mickalonis, J. I.; Murphy, T. R.; Berry, C. J.

2012-01-01

Under the L Basin corrosion surveillance program furniture rack coupons immersed for 14 years (FY2009 coupons) and 16 years (FY2011 coupons) were analyzed and the results trended with coupons exposed for shorter times. In addition, a section harvested from an actual furniture rack that was immersed for 14 years was analyzed for pitting in the weld and heat-affected-zone (HAZ) regions. The L Basin operations maintained very good water quality over the entire immersion period for these samples. These results for FY2009 and FY2011 coupons showed that the average pit depths for the 6061 and 6063 base metal are 1 and 2 mils, respectively, while those for the weld and HAZ are 3 and 4 mils, respectively. The results for the weld and HAZ regions are similar to coupons removed during the period of FY2003 to FY2007. These similarities indicate that the pit development occurred quickly followed by slow kinetics of increase in pit depth. For the actual furniture rack sample average pits of 5 and 2 mils were measured for the HAZ and weld, respectively. These results demonstrate that pitting corrosion of the aluminum furniture racks used to support the spent fuel occurs in waters of good quality. The corrosion kinetics or pit depth growth rate is much less that 1 mil/year, and would not impact long-term use of this material system for fuel storage racks in L Basin if good water quality is maintained

Laboratory glassware rack for seismic safety

Science.gov (United States)

Cohen, M. M. (Inventor)

1985-01-01

A rack for laboratory bottles and jars for chemicals and medicines has been designed to provide the maximum strength and security to the glassware in the event of a significant earthquake. The rack preferably is rectangular and may be made of a variety of chemically resistant materials including polypropylene, polycarbonate, and stainless steel. It comprises a first plurality of parallel vertical walls, and a second plurality of parallel vertical walls, perpendicular to the first. These intersecting vertical walls comprise a self-supporting structure without a bottom which sits on four legs. The top surface of the rack is formed by the top edges of all the vertical walls, which are not parallel but are skewed in three dimensions. These top edges form a grid matrix having a number of intersections of the vertical walls which define a number of rectangular compartments having varying widths and lengths and varying heights.

Benchmarking criticality analysis of TRIGA fuel storage racks.

Science.gov (United States)

Robinson, Matthew Loren; DeBey, Timothy M; Higginbotham, Jack F

2017-01-01

A criticality analysis was benchmarked to sub-criticality measurements of the hexagonal fuel storage racks at the United States Geological Survey TRIGA MARK I reactor in Denver. These racks, which hold up to 19 fuel elements each, are arranged at 0.61m (2 feet) spacings around the outer edge of the reactor. A 3-dimensional model was created of the racks using MCNP5, and the model was verified experimentally by comparison to measured subcritical multiplication data collected in an approach to critical loading of two of the racks. The validated model was then used to show that in the extreme condition where the entire circumference of the pool was lined with racks loaded with used fuel the storage array is subcritical with a k value of about 0.71; well below the regulatory limit of 0.8. A model was also constructed of the rectangular 2×10 fuel storage array used in many other TRIGA reactors to validate the technique against the original TRIGA licensing sub-critical analysis performed in 1966. The fuel used in this study was standard 20% enriched (LEU) aluminum or stainless steel clad TRIGA fuel. Copyright © 2016. Published by Elsevier Ltd.

The optimization of spent fuel assembly storage racks in nuclear power plants

International Nuclear Information System (INIS)

Wang Yan

2005-01-01

This paper gives an evaluation of the spent fuel assembly storage racks in the nuclear power plants at home and abroad, focusing on the characteristics of the high density storage racks and the aseismatic design. It mainly discusses structures and characteristics of the spent fuel assembly storage racks in the Qinshan nuclear power phase II project. Concluding the crucial technical difficulties of the high density spent fuel assembly storage racks: the neutron-absorbing materials, the structural aseismatic design technology and the security analysis technology, this paper firstly generalizes several important neutron-absorbing materials, then introduces the evolution of the aseismatic design of the spent fuel assembly storage racks . In the last part, it describes the advanced aseismatic analysis technology in the Qinshan nuclear power phase II project. Through calculation and analysis for such storage racks, the author concludes several main factors that could have an influence on the aseismatic performance and thus gives the key points and methods for designing the optimal racks and provides some references for the design of advanced spent fuel assembly storage racks in the future. (authors)

Rack Distribution Effects on MPLM Center of Mass

Science.gov (United States)

Tester, John T.

2005-01-01

This research was in support of exploring the need for more flexible "center of gravity (CG) specifications than those currently established by NASA for the Multi-Purpose Logistics Module (MPLM). The MPLM is the cargo carrier for International Space Station (ISS) missions. The MPLM provides locations for 16 standard racks, as shown in Figure 1; not all positions need to be filled in any given flight. The MPLM coordinate system (X(sub M), Y(sub M), Z(sub M)) is illustrated as well. For this project, the primary missions of interest were those which supply the ISS and remove excess materials on the return flights. These flights use a predominate number of "Resupply Stowage Racks" (RSR) and "Resupply Stowage Platforms" (RSP). In these two types of racks, various smaller items are stowed. Hence, these racks will exhibit a considerable range of mass values as well as a range as to where their individual CG are located.

Nonlinear dynamic response of whole pool multiple spent fuel racks subject to three-dimensional excitations

International Nuclear Information System (INIS)

Zhao, Y.; Wilson, P.R.; Stevenson, J.D.

1995-01-01

The seismic evaluation of submerged free standing spent fuel storage racks is more complicated than most other nuclear structural systems. When subjected to three dimensional (3-D) floor seismic excitations the dynamic responses of racks in a pool are hydro dynamically coupled with each other, with the fuel assemblies water in gaps. The motion behavior of the racks is significantly different from that observed using a 3D single rack mode. Few seismic analyses using 3-D whole pool multiple rack models are available in the literature. I this paper an analysis was performed for twelve racks using potential theory for the fluid-structure interaction, and using a 3-D whole pool multi-rack finite element model developed herein. The analysis includes the potential nonlinear dynamic behavior of the impact of fuel-rack, rack-rack and rack-pool wall, the tilting or uplift and the frictional sliding of rack supports, and the impact of the rack supports to the pool floor. (author). 12 refs., 7 figs., 1 tab

A water-cooling solution for PC-racks of the LHC experiments

CERN Document Server

Vannerem, P

2004-01-01

With ever increasing power consumption and heat dissipation of todays CPUs, cooling of rack-mounted PCs is an issue for the future online farms of the LHC experiments. In order to investigate the viability of a water-cooling solution, a prototype PC-farm rack has been equipped with a commercially available retrofitted heat exchanger. The project has been carried out as a collaboration of the four LHC experiments and the PH-ESS group . This note reports on the results of a series of cooling and power measurements of the prototype rack with configurations of 30 to 48 PCs. The cooling performance of the rack-cooler is found to be adequate; it extracts the heat dissipated by the CPUs efficiently into the cooling water. Hence, the closed PC rack transfers almost no heat into the room. The measurements and the failure tests show that the rack-cooler concept is a viable solution for the future PC farms of the LHC experiments.

A Study on Rack Thickness Effect for Spent Fuel Pool Storage

International Nuclear Information System (INIS)

Kim, Mi Jin; Lee, Hee-Jae; Sohn, Dong-Seong

2015-01-01

For the effective storage of used fuel, the development of high performance neutron absorbing materials is needed. One of the major concern for the used fuel storage is the assurance to keep subcriticality of the storage rack and the high performance neutron absorbing material is the vital part to assure this requirement. According to NRC guide line, the k-effective of the spent fuel storage racks must not exceed 0.95. To ensure its safety, subcriticality analysis is required. Subcriticality analysis of the used storage in spent fuel pool have been performed by different authors. Criticality calculations for light water reactor spent fuel storage rack were carried out by Jae et al. They used AMPX-KENO IV code and considered the effect of rack pitch and rack thickness for consolidated fuel. The criticality analysis has performed at Gd 0.2 and 1 wt% according to thickness change. As thickness increases, the volume of the spent fuel pool rack increases. Therefore, absorbing material also increases according to thickness

A Study on Rack Thickness Effect for Spent Fuel Pool Storage

Energy Technology Data Exchange (ETDEWEB)

Kim, Mi Jin; Lee, Hee-Jae; Sohn, Dong-Seong [Ulsan National Institute of Science and Technology, Ulsan (Korea, Republic of)

2015-05-15

For the effective storage of used fuel, the development of high performance neutron absorbing materials is needed. One of the major concern for the used fuel storage is the assurance to keep subcriticality of the storage rack and the high performance neutron absorbing material is the vital part to assure this requirement. According to NRC guide line, the k-effective of the spent fuel storage racks must not exceed 0.95. To ensure its safety, subcriticality analysis is required. Subcriticality analysis of the used storage in spent fuel pool have been performed by different authors. Criticality calculations for light water reactor spent fuel storage rack were carried out by Jae et al. They used AMPX-KENO IV code and considered the effect of rack pitch and rack thickness for consolidated fuel. The criticality analysis has performed at Gd 0.2 and 1 wt% according to thickness change. As thickness increases, the volume of the spent fuel pool rack increases. Therefore, absorbing material also increases according to thickness.

Behavior of high-density spent-fuel storage racks

International Nuclear Information System (INIS)

Bailey, W.J.

1986-08-01

Included in this report is a summary of information on neutron-absorbing materials such as B 4 C in an aluminum matrix or organic binder material, stainless steel-boron and aluminum-boron alloys, and stainless steetl-clad cadmium that are used in high-density spent fuel storage racks. A list of the types of neutron-absorbing materials being used in spent fuel storage racks at domestic commercial plants is provided. Recent cases at several domestic plants where swelling of rack side plates (where the B 4 C in an aluminum matrix and B 4 C in an organic binder material were located) occurred are reviewed

Laboratory racks are installed in the MPLM Leonardo

Science.gov (United States)

2000-01-01

In the Space Station Processing Facility, another laboratory rack is placed on the arm of the Rack Insertion Unit to lift it to the workstand height of the Multi-Purpose Logistics Module Leonardo (not seen). The MPLM will transport laboratory racks filled with equipment, experiments and supplies to and from the International Space Station aboard the Space Shuttle. Leonardo will be launched for the first time March 1, 2001, on Shuttle mission STS-102. On that flight, Leonardo will be filled with equipment and supplies to outfit the U.S. laboratory module, being carried to the ISS on the Jan. 19, 2001, launch of STS-98.

Effects of poison panel shrinkage and gaps on fuel storage rack reactivity

International Nuclear Information System (INIS)

Boyd, W.A.; Mueller, D.E.

1988-01-01

Fixed poison panels are used in spent fuel rack designs to increase enrichment limits and reduce cell spacing; therefore, assurances that the maximum rack reactivity will meet the design limit (0.95) throughout the lifetime of the racks depend on the continued effectiveness of the poison with time. Industry data have shown that poison panels will shrink under irradiated conditions. From recent data, however, poison panels have been found to have gaps spanning their width after relatively short operating periods. This paper presents results of studies showing the fuel rack reactivity changes associated with poison panel shrinkage and formation of gaps. The discovery of gaps in the fuel rack poison panels at an operating plant raises concerns regarding the effectiveness of the poison over the lifetime of the fuel racks. Studies performed to evaluate the effect of the poison panel shrinkage on reactivity show that reactivity changes from zero to several percent are possible depending on the initial panel size. Results of recent studies show that some gaps can be accommodated in the fuel rack poison panels at the fuel midplane without causing the fuel rack K eff limit to be exceeded. With worst-case assumptions concerning gap size and the number of panels affected, other actions will likely be required to show that the rack K eff design limit will not be exceeded

Fuel storage rack

International Nuclear Information System (INIS)

Mollon, L.

1977-01-01

Disclosed is a storage rack for spent nuclear fuel elements comprising a multiplicity of elongated hollow containers of uniform cross-section, preferably square,some of said containers having laterally extending continuous flanges extending between adjacent containers and defining continuous elongated chambers therebetween for the reception of neutron absorbing panels. 18 claims, 7 figures

Nuclear reactor spent fuel storage rack

International Nuclear Information System (INIS)

Machado, O.J.; Flynn, W.M.; Flanders, H.E. Jr.; Booker, L.W.

1989-01-01

A fuel rack is described for use in storing nuclear fuel assemblies in a nuclear fuel storage pool having a floor on which an upwardly projecting stud is mounted; the fuel rack comprising: a base structure at the lower end of the fuel rack including base-plate means having flow openings therein, the base-plate means supporting a first network of interlaced beams which form a multiplicity of polygonal openings; a second network of interlaced beams forming polygonal openings positioned in spaced vertical alignment with corresponding polygonal openings in the first network of beams; a plurality of cells, each cell having sides bounded by inner and outer surfaces and being of a size and configuration designed to hold therein a fuel assembly, each cell positioned in a corresponding pair of the aligned polygonal openings, each cell being open at both ends with a guiding funnel at the upper end, and the cells being positioned over the flow openings in the base-plate to permit flow of coolant through the cells; spaced, outwardly directed, projections on the outer surfaces of the sides of the cells near the tops and bottoms of the sides thereof, each cell being sized to be received within a corresponding of the pair of aligned polygonal openings in which the cells are respectively positioned; and means fixedly securing the projections to the beams in the first and second networks of beams thereby to provide a substantially rigid fuel rack of modular design

Anne-Ly Reimaa : "Suhtlemisel on oluline avatus" / Anne-Ly Reimaa ; interv. Tiia Linnard

Index Scriptorium Estoniae

Reimaa, Anne-Ly

2005-01-01

Ilmunud ka: Severnoje Poberezhje : Subbota 3. september lk. 5. Intervjueeritav oma tööst Brüsselis, kus esindab Eesti linnade liitu ja Eesti maaomavalitsuste liitu. Arvamust avaldavad Anne Jundas ja Kaia Kaldvee. Lisa: CV

Chin Shan analyses show advantages of whole pool multi-rack approach

International Nuclear Information System (INIS)

Singh, K.P.; Soler, A.I.

1991-01-01

Nuclear fuel storage racks are essentially thin-walled, cellular structures of prismatic cross-section. Although the details of design vary from one supplier to another, certain key physical attributes are common to all designs. For example, all racks feature square cells of sufficient opening size and height to enable insertion and withdrawal of the fuel assembly. The array of cells is positioned in a vertical orientation and is supported off the pool slab surface by four or more support legs. The spent fuel pool is filled with the individual fuel racks. The plenum created by the support legs is essential for proper cooling of the fuel assemblies stored in the rack, which relies on natural convective cooling to extract the heat emitted by the spent fuel. However, it has the insalutary effect of making it kinematically less stable. Regulatory authorities require careful and comprehensive analysis of the response of the racks under the seismic motions postulated for the pool slab. Results from whole pool multi-rack (WPMR) analyses at the Chin Shan and Oyster Creek nuclear plants point up the potential inadequacies of single rack 3D analyses, and show just how important it is to carry out WPMR simulations, despite their abstruseness and high cost. (author)

Nonlinear analyses of spent-fuel racks for consolidated fuel loading

International Nuclear Information System (INIS)

Kabir, A.F.; Godha, P.C.; Malik, L.E.; Bolourchi, S.

1987-01-01

Storage racks for spent-fuel assemblies in nuclear power plants are designed to withstand various combinations of loads generated by gravity, seismic, thermal, and accidental fuel drops. Due to the need for storing increased amounts of spent fuel in the existing fuel pools, many nuclear power utilities are evaluating existing fuel racks to safely carry the additional loads. The current study presents the seismic analyses of existing fuel racks of Northeast Utility Company's Millstone Unit Number 1 (BWR Mark I) nuclear plant to accommodate a 2:1 fuel consolidation. This objective requires rigorous nonlinear analyses to establish the full available capacities of the racks and thereby avoid expensive modifications or minimize any needed upgrades

THE FEMINISM AND FEMININITY OF ANN VERONICA IN H. G. WELLS' ANN VERONICA

Directory of Open Access Journals (Sweden)

Liem Satya Limanta

2002-01-01

Full Text Available H.G. Well's Ann Veronica structurally seems to be divided into two parts; the first deals with Ann Veronica's struggle to get equality with men and freedom in most aspects of life, such as in politics, economics, education, and sexuality; the second describes much the other side of her individuality which she cannot deny, namely her femininity, such as her crave for love, marriage, maternity, and beauty. H.G. Wells describes vividly the two elements in Ann Veronica, feminism and femininity. As a feminist, Ann Veronica rebelled against her authoritative Victorian father, who regarded women only as men's property to be protected from the harsh world outside. On the other side, Ann could not deny her being a woman after she fell in love with Capes. Her femininity from the second half of the novel then is explored. Although the novel ends with the depiction of the domestic life of Ann Veronica, it does not mean that the feminism is gone altogether. The key point is that the family life Ann chooses as a `submissive' wife and good mother is her choice. It is very different if it is forced on her to do. Thus, this novel depicts both sides of Ann Veronica, her feminism and her femininity.

'Swab racks are an old fashioned idea'.

Science.gov (United States)

Mumford, M

1991-12-01

Mary Mumford, theatre sister at the Princes of Wales Hospital, Bridgend, was asked to speak in a short debate at an NATN branch meeting, supporting the motion that 'swab racks are an old fashioned idea'. Although she did not like swab racks she had not attempted thus far to do anything about them. In the event, she actually lost the debate--not in principle but because she could offer no effective alternative method of checking swabs. Having been given the incentive, a trial is now being conducted in her hospital similar to that described by Paul Wicker. This is the case presented by Mary Mumford supporting the following motion ... 'that swab racks are an old fashioned idea, which cause more potential problems due to exposure of blood than is proven to be safe in today's theatre environment'.

Criticality safety analysis of the NPP Krsko storage racks

International Nuclear Information System (INIS)

Kromar, M.; Kurincic, B.

2002-01-01

NPP Krsko is going to increase the capacity of the spent fuel storage pool by replacement of the existing racks with high-density racks. This will be the second reracking campaign since 1983 when storage was increased from 180 to 828 storage locations. The pool capacity will increase from 828 to 1694 with partial reracking by the spring 2003. The installed capacity will be sufficient for the current design plant lifetime. Complete reracking of the spent fuel pool will additionally increase capacity to 2321 storage locations. The design, rack manufacturing and installation has been awarded to the Framatome ANP GmbH. Burnup credit methodology, which was approved by the Slovenian Nuclear Safety Administration in previous licensing of existing racks, will be again implemented in the licensing process with the recent methodology improvements. Specific steps of the criticality safety analysis and representative results are presented in the paper.(author)

Accident Analysis of High Density Storage Rack for Fresh Fuel Assemblies

International Nuclear Information System (INIS)

Jang, K. J.; Lee, M. J.; Jin, H. U.; Park, J. H.; Shin, S. Y.

2009-01-01

Recently KONES and KNF have developed the so called suspension-type High Density Storage Rack (HDSR) for fresh fuel assemblies. The USNRC OT position paper specifies that the design of the rack must ensure the functional integrity of the fuel racks under all credible fuel assembly drop events. In this context the functional integrity means the criticality safety. That is to say, the drop events must not bring any danger to the criticality safety of HDSR. This paper shows the results of the analysis carried out to demonstrate the regulatory compliance of the proposed racks under postulated accidental drop events

Evolution of design concepts for remotely maintainable equipment racks

International Nuclear Information System (INIS)

Peishel, F.L.; Mouring, R.W.; Schrock, S.L.

1986-01-01

Equipment racks have been used to support process equipment in radioactive facilities for many years. Improvements in the design of these racks have evolved relatively slowly primarily as a result of limitations in the capabilities of maintenance equipment; that is, tasks could only be approached from above using bridge cranes with viewing primarily through periscopes. In recent years, however, technological advances have been made by the Consolidated Fuel Reprocessing Program (CFRP) at Oak Ridge National Laboratory (ORNL) in bridge-mounted servomanipulators with onboard auxiliary hoists and television viewing systems. These advances permit full cell coverage by the manipulator arms which, in turn, allow maintenance tasks to be approached horizontally as well as from above. Maintainable equipment items can be stacked vertically on a rack because total overhead access is less important and maintenance tasks that would not have been attempted in the past can now be performed. These advances permit greater flexibility in the design and cell layout of the racks and lead to concepts that could significantly increase the availability of a facility. The evolution of rack design and a description of the alternative concepts based on present maintenance systems capabilities are presented in this paper. 13 refs., 11 figs

Improved method to demonstrate the structural integrity of high density fuel storage racks

International Nuclear Information System (INIS)

Hinderks, M.; Ungoreit, H.; Kremer, G.

2001-01-01

Reracking of existing fuel pools to the maximum extent is desirable from an economical point of view. This goal can be achieved by minimizing the gaps between the spent fuel storage racks. Since the rack design is aimed at enabling consolidated fuel rod storage, additional requirements arise with respect to the design and the structural analysis. The loads resulting from seismic events are decisive for the structural analysis and require a specially detailed and in-depth analysis for high seismic loads. The verification of structural integrity and functionality is performed in two phases. In the first phase the motional behavior of single racks, rows of racks and, where required, of all racks in the pool is simulated by excitation with displacement time histories under consideration of the fluid-structure interaction (FSI). The displacements from these simulations are evaluated, while the loads are utilized as input data for the structural analysis of the racks and the pool floor. The structural analyses for the racks comprise substantially stress analyses for base material and welds as well as stability analyses for the support channels and the rack outside walls. The analyses are performed in accordance with the specified codes and standards

Manufacturing and Construction of Fresh Fuel Storage Rack for a Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Oh, Jinho; Lee, Sangjin; Lee, Jongmin; Ryu, Jeong-Soo [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The objective of this study is to provide the manufacturing and construction information regarding the Fresh Fuel Storage Rack (FFSR). The main function of a FFSR is to store and protect the 2 core new fuel assemblies for the operation of the research reactor. The fresh fuel assemblies are stored in a rack made of stainless steel and the storage rack is installed in the fresh fuel storage room. The fresh fuel facility provides fresh fuel assemblies with dry storage space. General design requirements of the fresh fuel storage facilities are given in the ANSI-57.3. Design, manufacturing, and construction of the fresh fuel storage rack are introduced. The analysis is performed to confirm the structural intensity of the fresh fuel storage rack under the seismic loads. The fresh fuel storage rack designed for storage of fresh fuel assemblies should be manufactured and installed with consideration of predicted number of fresh fuel assemblies, structural integrity, resistivity to corrosion and radiation, cleaning, and workability.

Manufacturing and Construction of Fresh Fuel Storage Rack for a Research Reactor

International Nuclear Information System (INIS)

Oh, Jinho; Lee, Sangjin; Lee, Jongmin; Ryu, Jeong-Soo

2016-01-01

The objective of this study is to provide the manufacturing and construction information regarding the Fresh Fuel Storage Rack (FFSR). The main function of a FFSR is to store and protect the 2 core new fuel assemblies for the operation of the research reactor. The fresh fuel assemblies are stored in a rack made of stainless steel and the storage rack is installed in the fresh fuel storage room. The fresh fuel facility provides fresh fuel assemblies with dry storage space. General design requirements of the fresh fuel storage facilities are given in the ANSI-57.3. Design, manufacturing, and construction of the fresh fuel storage rack are introduced. The analysis is performed to confirm the structural intensity of the fresh fuel storage rack under the seismic loads. The fresh fuel storage rack designed for storage of fresh fuel assemblies should be manufactured and installed with consideration of predicted number of fresh fuel assemblies, structural integrity, resistivity to corrosion and radiation, cleaning, and workability

Three-dimensional seismic analysis for spent fuel storage rack

International Nuclear Information System (INIS)

Lee, Gyu Mahn; Kim, Kang Soo; Park, Keun Bae; Park, Jong Kyun

1998-01-01

Time history analysis is usually performed to characterize the nonlinear seismic behavior of a spent fuel storage rack (SFSR). In the past, the seismic analyses of the SFSR were performed with two-dimensional planar models, which could not account for torsional response and simultaneous multi-directional seismic input. In this study, three-dimensional seismic analysis methodology is developed for the single SFSR using the ANSY code. The 3-D model can be used to determine the nonlinear behavior of the rack, i.e., sliding, uplifting, and impact evaluation between the fuel assembly and rack, and rack and the pool wall. This paper also reviews the 3-D modeling of the SFSR and the adequacy of the ANSYS for the seismic analysis. As a result of the adequacy study, the method of ANSYS transient analysis with acceleration time history is suitable for the seismic analysis of highly nonlinear structure such as an SFSR but it isn't appropriate to use displacement time history of seismic input. (author)

Flow field mapping in data rack model

Directory of Open Access Journals (Sweden)

Matěcha J.

2013-04-01

Full Text Available The main objective of this study was to map the flow field inside the data rack model, fitted with three 1U server models. The server model is based on the common four-processor 1U server. The main dimensions of the data rack model geometry are taken fully from the real geometry. Only the model was simplified with respect to the greatest possibility in the experimental measurements. The flow field mapping was carried out both experimentally and numerically. PIV (Particle Image Velocimetry method was used for the experimental flow field mapping, when the flow field has been mapped for defined regions within the 2D/3D data rack model. Ansys CFX and OpenFOAM software were used for the numerical solution. Boundary conditions for numerical model were based on data obtained from experimental measurement of velocity profile at the output of the server mockup. This velocity profile was used as the input boundary condition in the calculation. In order to achieve greater consistency of the numerical model with experimental data, the numerical model was modified with regard to the results of experimental measurements. Results from the experimental and numerical measurements were compared and the areas of disparateness were identified. In further steps the obtained proven numerical model will be utilized for the real geometry of data racks and data.

Casimir rack and pinion as a miniaturized kinetic energy harvester

Science.gov (United States)

Miri, MirFaez; Etesami, Zahra

2016-08-01

We study a nanoscale machine composed of a rack and a pinion with no contact, but intermeshed via the lateral Casimir force. We adopt a simple model for the random velocity of the rack subject to external random forces, namely, a dichotomous noise with zero mean value. We show that the pinion, even when it experiences random thermal torque, can do work against a load. The device thus converts the kinetic energy of the random motions of the rack into useful work.

40 CFR 63.2475 - What requirements must I meet for transfer racks?

Science.gov (United States)

2010-07-01

... transfer racks? 63.2475 Section 63.2475 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... must I meet for transfer racks? (a) You must comply with each emission limit and work practice standard in table 5 to this subpart that applies to your transfer racks, and you must meet each applicable...

Refurbishment of the rotating rack of the OSU TRIGA MKII reactor

International Nuclear Information System (INIS)

Higginbotham, J.F.; Dodd, B.; Pratt, D.S.; Anderson, T.V.

1992-01-01

Many TRIGA reactors have experienced operational difficulties with the rotating racks used for sample irradiation. Generally the rack gradually becomes more difficult to rotate until it finally seizes. The recommended action at that point is replacement of the entire facility at a significant cost. The purpose of this paper is to describe the symptoms leading to rack failure and to present the results of a refurbishment procedure that does not involve the use of solvents which create mixed chemical and radioactive hazardous waste. The primary reason for rack failure is the buildup of sludge produced through irradiation of lubrication oil. The refurbishment procedure involves using a commercially available degreasing solution which can be pumped into and out of the rack with the objective of removing this sludge. The solution used is sold under the trade name 'Simple Green'. No radioactive material was detected on smear or air samples taken of the work area during the reifurbishment activities and the rack rotates freely in both direction even after eighteen months of operation. The only disadvantage to performing this procedure has been the need to maintain a very aggressive contamination control program when unloading samples from the rack. A very fine particulate material attaches to the outside of tubes used to encapsulate samples. This material can produce contamination levels of 10,000 dpm/100 cm 2 in the worst cases but will typically produce local hot spots on the order of 1000 dpm. (author)

Inspection and Analysis of Aluminum Storage Racks in Spent Fuel Storage Basins

International Nuclear Information System (INIS)

Howell, J.P.; Nelson, D.Z.

1998-07-01

Aluminum-clad spent nuclear fuel is stored in water filled basins at the Savannah River Site awaiting processing or other disposition. After more than 35 years of service underwater, the aluminum storage racks that position the fuel bundles in the basin were replaced. During the removal of the racks from the basin, a failure occurred in one of the racks and the Savannah River Technology Center was asked to investigate. This paper presents results of the failure analysis and provides a discussion of the effects of corrosion on the structural integrity of the storage racks

Rack Aware Data Placement for Network Consumption in Erasure-Coded Clustered Storage Systems

Directory of Open Access Journals (Sweden)

Bilin Shao

2018-06-01

Full Text Available The amount of encoded data replication in an erasure-coded clustered storage system has a great impact on the bandwidth consumption and network latency, mostly during data reconstruction. Aimed at the reasons that lead to the excess data transmission between racks, a rack aware data block placement method is proposed. In order to ensure rack-level fault tolerance and reduce the frequency and amount of the cross-rack data transmission during data reconstruction, the method deploys partial data block concentration to store the data blocks of a file in fewer racks. Theoretical analysis and simulation results show that our proposed strategy greatly reduces the frequency and data volume of the cross-rack transmission during data reconstruction. At the same time, it has better performance than the typical random distribution method in terms of network usage and data reconstruction efficiency.

Arbitrary vehicle steering characteristics with changing ratio rack and pinion transmission

Directory of Open Access Journals (Sweden)

András G Bendefy

2015-12-01

Full Text Available In order to achieve arbitrary steering characteristics at vehicles, a steering mechanism was developed, in which changing ratio rack and pinion connections have been applied. In contrary to a regular steering mechanism where only a single rack is used, two racks were applied in order to make arbitrary characteristics possible. The turning wheel’s required motion functions had to be defined first, thereafter could we determine the changing ratio rack and pinion geometry which produces this motion. First, a simplified two-dimensional mockup was created in order to study the difficulties and possibilities of a real construction. Later, a fully functional assembly was designed and manufactured to make further experiments possible.

Arabidopsis scaffold protein RACK1A modulates rare sugar D-allose regulated gibberellin signaling.

Science.gov (United States)

Fennell, Herman; Olawin, Abdulquadri; Mizanur, Rahman M; Izumori, Ken; Chen, Jin-Gui; Ullah, Hemayet

2012-11-01

As energy sources and structural components, sugars are the central regulators of plant growth and development. In addition to the abundant natural sugars in plants, more than 50 different kinds of rare sugars exist in nature, several of which show distinct roles in plant growth and development. Recently, one of the rare sugars, D-allose, an epimer of D-glucose at C3, is found to suppress plant hormone gibberellin (GA) signaling in rice. Scaffold protein RACK1A in the model plant Arabidopsis is implicated in the GA pathway as rack1a knockout mutants show insensitivity to GA in GA-induced seed germination. Using genetic knockout lines and a reporter gene, the functional role of RACK1A in the D-allose pathway was investigated. It was found that the rack1a knockout seeds showed hypersensitivity to D-allose-induced inhibition of seed germination, implicating a role for RACK1A in the D-allose mediated suppression of seed germination. On the other hand, a functional RACK1A in the background of the double knockout mutations in the other two RACK1 isoforms, rack1b/rack1c, showed significant resistance to the D-allose induced inhibition of seed germination. The collective results implicate the RACK1A in the D-allose mediated seed germination inhibition pathway. Elucidation of the rare sugar signaling mechanism will help to advance understanding of this less studied but important cellular signaling pathway.

Development of a cosmic rack for characterization of RPCs

International Nuclear Information System (INIS)

Sehgal, S.T.; Pant, L.M.

2011-01-01

A newly designed cosmic rack has been commissioned this year in the RPC Lab., in NPD-BARC. The rack consists of nine shelves each providing a clear area of 160 cm x 225 cm. Each of the shelf is separated by a distance of 30 cm, providing sufficient distance for fast electronics to respond and also providing an easy access for loading and removing the RPCs. The total height of the cosmic rack is 2.8 metres. A typical fully integrated RPCs covers an approximate area of 2 m 2 and weighs about 60-70 kg. The rack has been basically designed, keeping in mind the varied requirements as regards to the RPCs based current and futuristic programmes which are listed as follows: 1. Testing of large area trapezoidal bakelite gas-gaps and RPCs for the CMS experiment, keeping in mind the production rate of five RPCs per month. 2. The proposed muon tomography programme with 1m x 1m glass RPCs and 3. Characterization of glass RPCs (1m x 2m) for the INO experiment in near future

Rack for storage of nuclear fuel elements

International Nuclear Information System (INIS)

Bosshart, E.

1987-01-01

The rack contains a cluster of parallel, approximately vertical, neutron absorbing square section tubes which are attached to a bottom plate and mutually supported along their edges using welded joining pieces. These welded pieces touch each other laterally in at least one middle plane where the rack is joined. The pieces are additionally secured laterally by screws. Thereby a safe and simple mutual support of the tubes is achieved. It is possible to dismount the tubes by releasing the screws without the necessity to move the tubes in a horizontal direction. 4 figs

CM-2 Environmental/Modal Testing of SPACEHAB Racks

Science.gov (United States)

McNelis, Mark E.; Goodnight, Thomas W.

2001-01-01

Combined environmental/modal vibration testing has been implemented at the NASA Glenn Research Center's Structural Dynamics Laboratory. The benefits of combined vibration testing are that it facilitates test article modal characterization and vibration qualification testing. The Combustion Module-2 (CM-2) is a space experiment that will launch on shuttle mission STS-107 in the SPACEHAB Research Double Module. The CM-2 flight hardware is integrated into a SPACEHAB single and double rack. CM-2 rack-level combined vibration testing was recently completed on a shaker table to characterize the structure's modal response and verify the random vibration response. Control accelerometers and limit force gauges, located between the fixture and rack interface, were used to verify the input excitation. Results of the testing were used to verify the loads and environments for flight on the shuttles.

Dynamic response of piping system on rack structure with gaps and frictions

International Nuclear Information System (INIS)

Kobayashi, Hiroe; Yoshida, Misutoyo; Ochi, Yoshio

1989-01-01

In the seismic design of a piping system on a rack structure, the interaction between the piping system and the rack structure must be evaluated under the condition that the rack structure is not stiff and heavy enough compared with the piping system. Moreover, there are local nonlinearities due to the gap and friction between the piping system and the rack structure. This paper presents the influence of the interaction and the local nonlinearities upon the seismic response by numerical study and a vibration test using a shaking table. In the numerical study, the piping system and the rack structure were represented by the three degrees of freedom mass-spring model taking a vibration mode of the piping system into account. The nonlinearities due to gap and friction were defined as a function of motion and treated as the pseudo force vector (additional applied force) in an equation of motion. From the results of the numerical study and the vibration test, it was clarified that seismic response of both the rack structure and the piping system is reduced by gap and friction. Moreover, the piping system and rack structure can be represented by the three degrees of freedom mass spring model. And the local nonlinearities can be treated by the pseudo force in an equation of motion. (orig.)

Development of seismic design method for free standing rack and applicability to Japanese nuclear power plant

International Nuclear Information System (INIS)

Takaki, Yu; Taniguchi, Katsuhiko; Kishimoto, Junichi; Iwasaki, Akihisa; Nekomoto, Yoshitsugu; Kuga, Tohru; Kameyama, Masashi

2017-01-01

Free standing racks which are not anchored to the pool floor nor walls have never been adopted in Japan. Under an earthquake, behaviors of free standing racks are nonlinear and involve a complex combination of motions (sliding, rocking, and twisting) and impacts between a fuel assembly and the fuel cell walls and between a pit floor and rack pedestals. To predict a seismic response of free standing racks, the seismic analysis requires careful considerations of these complex phenomena (sliding, rocking, and twisting), fluid coupling effects and frictional effects. We carried out seismic experiments on the full-scale rack model in both water and dry conditions and obtained the fundamental data about behavior of free standing racks (sliding, and rocking motions). We have developed the nonlinear dynamic analysis method to predict seismic response of free standing racks utilizing the full-scale test result and verified the analysis evaluation method of free standing rack by comparison between analysis results and experimental data. Furthermore, we applied the seismic design method to the free standing rack in the Japanese nuclear plant (Mihama nuclear power station Unit 3), and verified that the free standing rack was applicable to Japanese nuclear plant. (author)

Effects of suspension of air-conditioning on airtight-type racks.

Science.gov (United States)

Kanzaki, M; Fujieda, M; Furukawa, T

2001-10-01

Although isolation racks are superior to open-type racks in terms of securing breeding conditions for laboratory animals, the contingency-proofing capability of the former has yet to be determined. Therefore, from the view of risk management, we studied the environmental change in isolation racks by forcibly suspending ventilation and air-conditioning and confirming the maximal time length for complete recovery to the original condition after restarting their operations. The isolation racks were placed in a room that was equipped with an independent air-conditioning system. When the inside condition of the racks reached 22-24 degrees C and 59-64% of relative humidity, the air-conditioning and ventilation were forcibly suspended and the subsequent temperature, relative humidity, ammonium and CO2 concentrations in the racks were measured over time. We found that after suspending the air-conditioning and ventilation, it took 40-60 min for temperature, and about 10 min for relative humidity to exceed the maximum values (temperature and relative humidity) referred to in the Showa 58 Nenban Guideline Jikken Doubutsu Shisetsu no Kenchiku oyobi Setsubi (Guidelines of buildings and facilities for experimental animals in Japan; Year 1983 edition). After 17 hr 25 min of the suspension of air-conditioning and ventilation, two rats were found dead. Then, the air-conditioning and ventilation were restarted. It took about 2 hr for temperature, and 50 min for relative humidity to regain the guideline values. The ammonium concentration stayed within the guideline value with a maximum concentration of 2 ppm in the experimental period, whereas the CO2 concentration was found to exceed 9% at the time of animal death.

78 FR 63166 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Countervailing...

Science.gov (United States)

2013-10-23

... Shelving and Racks From the People's Republic of China: Countervailing Duty Administrative Review; 2011... order on certain kitchen appliance shelving and racks (kitchen racks) from the People's Republic of.... Scope of the Order This order covers shelving and racks for refrigerators, freezers, combined...

Influence of Rack Slope and Approaching Conditions in Bottom Intake Systems

Directory of Open Access Journals (Sweden)

Luis G. Castillo

2017-01-01

Full Text Available The study analyzes the flow over bottom racks made of longitudinal T-shaped bars. A clear water flow is considered in a laboratory flume. Free surface profiles, wetted rack lengths, and discharge coefficients are measured, changing parameters such as longitudinal slope, void ratio, and approaching flow. The present work complements existing experimental studies, considering the influence of the approaching flow conditions. The velocity field measured with Particle Image Velocimetry (PIV technique and the pressure field with Pitot tubes are quantified. Numerical simulations (CFD are used to complement laboratory data. The energy head along the rack is calculated and compared with the hypothesis of horizontal energy level with minimum energy at the beginning of the rack. A discharge coefficient adjustment that considers the slope, the void ratio, and the position along the rack is proposed and presented with the results of other works. Theoretical proposals to calculate the pressure field along the flow are compared with measurements in the laboratory. The relation between the static pressure head in the space of bars and the discharge coefficient is used as an alternative method to define the discharge.

The NRC activities concerning Boraflex use in spent-fuel storage racks

International Nuclear Information System (INIS)

Kopp, L.I.

1996-01-01

The U.S. Nuclear Regulatory Commission (NRC) has issued several generic communications to the nuclear industry identifying two issues with respect to using Boraflex in spent-fuel storage racks. The first issue related to gamma-radiation-induced shrinkage of Boraflex and the potential to develop tears or gaps in the material. This phenomenon is typically accounted for in criticality analyses of spent-fuel storage racks. The second issue concerned long-term Boraflex performance throughout the intended service life of the racks as a result of both gamma irradiation and exposure to the wet pool environment

Seismic testing of the base-isolated PWR spent-fuel storage rack

International Nuclear Information System (INIS)

Fujita, Katsuhisa; Tanaka, Mamoru; Nakamura, Masaaki; Tsujikura, Yonezo.

1990-01-01

The present paper aims to verify the seismic safety of the base-isolated spent-fuel storage rack. A series of seismic tests has been conducted using a three-dimensional shaking table. A sliding-type base-isolation system was employed for the prototype rack considering environmental conditions in an actual plant. A non linear seismic response analysis was also performed, and it is verified that the prototype of a base-isolated spent-fuel storage rack has a sufficient seismic safety margin for design seismic conditions from the viewpoint of seismic response. (author)

Engineering analyses of ITER divertor diagnostic rack design

Energy Technology Data Exchange (ETDEWEB)

Modestov, Victor S., E-mail: modestov@compmechlab.com [St Petersburg State Polytechnical University, 195251 St Petersburg, 29 Polytechnicheskaya (Russian Federation); Nemov, Alexander S.; Borovkov, Aleksey I.; Buslakov, Igor V.; Lukin, Aleksey V. [St Petersburg State Polytechnical University, 195251 St Petersburg, 29 Polytechnicheskaya (Russian Federation); Kochergin, Mikhail M.; Mukhin, Eugene E.; Litvinov, Andrey E.; Koval, Alexandr N. [Ioffe Physico-Technical Institute, 194021 St Petersburg, 26 Polytechnicheskaya (Russian Federation); Andrew, Philip [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France)

2013-10-15

Highlights: • The approach developed early has been used for the assessment of new design of DTS racks and neutron shield units. • Results of most critical EM and seismic analyses indicate that introduced changes significantly improved the system behaviour under these loads. • However further research is required to finalize the design and check it upon meeting all structural, thermal, seismic, EM and fatigue requirements. -- Abstract: The divertor port racks used as a support structure of the divertor Thomson scattering equipment has been carefully analyzed to be consistent with electromagnetic and seismic loads. It follows from the foregoing simulations that namely these analyses demonstrate critical challenges associated with the structure design. Based on the results of the reference structure [2] a modified design of the diagnostic racks is proposed and updated simulation results are given. The results signify a significant improvement over the previous reference layout and the design will be continued towards finalization.

Seismic response of free standing fuel rack construction to 3-D floor motion

International Nuclear Information System (INIS)

Soler, A.I.; Singh, K.

1983-01-01

Seismic analysis of free standing submerged racks is complicated by the presence of water and structural non-linearities such as fuel assembly cell impact and floor interface friction. A direct time integration technique has been proposed to analyze this class of structures. Application of the time integration technique on a fourteen degree of freedom lumped mass model of the rack reveals some heretofore unpublished quirks in the structure's behavior. The method of analysis is utilized to compare the seismic response of some representative rack designs. Results show wide differences in the structural response, depending on the fabrication details of racks

77 FR 61396 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Countervailing...

Science.gov (United States)

2012-10-09

... Shelving and Racks From the People's Republic of China: Countervailing Duty Administrative Review; 2010... order on certain kitchen appliance shelving and racks (``kitchen racks'') from the People's Republic of...-1785, respectively. Scope of the Order The scope of the order consists of shelving and racks for...

76 FR 62364 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

Science.gov (United States)

2011-10-07

... Shelving and Racks From the People's Republic of China: Preliminary Results of the Countervailing Duty... countervailable duty order on certain kitchen appliance shelving and racks (``Kitchen Racks'') from the People's...: Background On July 27, 2009, the Department published a CVD order on Kitchen Racks from the PRC. See Certain...

Replacement of the rotary specimen rack in the U.S. Geological Survey TRIGA Reactor (GSTR)

International Nuclear Information System (INIS)

Rusling, D.H.; Helfer, P.G.; Perryman, R.E.; Smith, W.L.

1986-01-01

A new rotary specimen rack was installed in the GSTR on November 13, 1985. The new rack has been modified to allow the pneumatic unloading of samples. Instructions for the removal and installation of the rotary specimen rack were provided by GA Technologies. The first step was to prepare the core for removal of the control rods, T/C fuel elements, and the central thimble. The rack was weighted prior to removal to ensure that it could not float to the surface. The old rack was stored at the side of the tank. Radiation measurements were made with an underwater ion chamber. (author)

Design Features and Capabilities of the First Materials Science Research Rack

Science.gov (United States)

Pettigrew, P. J.; Lehoczky, S. L.; Cobb, S. D.; Holloway, T.; Kitchens, L.

2003-01-01

The First Materials Science Research Rack (MSRR-1) aboard the International Space Station (ISS) will offer many unique capabilities and design features to facilitate a wide range of materials science investigations. The initial configuration of MSRR-1 will accommodate two independent Experiment Modules (EMS) and provide the capability for simultaneous on-orbit processing. The facility will provide the common subsystems and interfaces required for the operation of experiment hardware and accommodate telescience capabilities. MSRR1 will utilize an International Standard Payload Rack (ISPR) equipped with an Active Rack Isolation System (ARIS) for vibration isolation of the facility.

Analysis of ICPP fuel storage rack inner tie and corner tie substructures

Energy Technology Data Exchange (ETDEWEB)

Nitzel, M.E.; Rahl, R.G.

1996-01-01

Finite element models were developed and analyses performed for the tie plate, inner tie block assembly, and corner tie block assembly of a 25 port fuel rack assembly designed for installation in Pool 1 of Building 666 at the Idaho Chemical Processing Plant. These models were specifically developed to investigate the adequacy of certain welds joining components of the fuel storage rack assembly. The work scope for the task was limited to an investigation of the stress levels in the subject subassemblies when subjected to seismic loads. Structural acceptance criteria used for the elastic calculations performed were as found in the overall rack design report as issued by the rack`s designer, Holtec International. Structural acceptance criteria used for the plastic calculations performed as part of this effort were as defined in Subsection NF and Appendix F of the ASME Boiler & Pressure Vessel Code. The results of the analyses will also apply to the 30 port fuel storage rack design that is also scheduled for installation in Pool 1 of ICPP 666. The results obtained from the analyses performed for this task indicate that the welds joining the inner tie block and corner tie block to the surrounding rack structure meet the acceptance criteria. Further, the structural members (plates and blocks) were also found to be within the allowable stress limits established by the acceptance criteria. The separate analysis performed on the inner tie plate confirmed the structural adequacy for both the inner tie plate, corner tie plate, and tie block bolts. The analysis results verified that the inner tie and corner tie block should be capable of transferring the expected seismic load without structural failure.

77 FR 21744 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Final Results...

Science.gov (United States)

2012-04-11

... Shelving and Racks From the People's Republic of China: Final Results of the Countervailing Duty... countervailable duty order on certain kitchen appliance shelving and racks (``Kitchen Racks'') from the People's... Kitchen Appliance Shelving and Racks from the People's Republic of China: Preliminary Results of...

Head losses in small hydropower plant trash racks (SHP

Directory of Open Access Journals (Sweden)

N. Walczak

2016-12-01

Full Text Available Small hydropower plants (SHP are technical facilities that are part of alternative energy sources [Paish 2002]. They are primarily characterised by low unit power (in Poland below 5 MW and are often constructed on existing barrages. Electrical current produced by these plants is used to meet local demand. Considering the exploitation of SHPs, it is important to ensure a stable flow through turbines. Aggidis et al. [2010] analysed SHP equipment costs depending on the turbine set. The turbines are protected against damage with trash racks applied for capturing water-borne detritus, such as plant debris carried by water. However, trash racks as solid equipment of SHPs cause head losses, and as a consequence reduce the efficiency of the system. These losses result not only from the spacing of bars, their shape and the technical condition of the inlet chamber, but also from plant debris, its nature, and the quantity of accumulated material that effectively limits the flow. The plant debris captured on trash racks is characterised by diversity in terms of species composition related to the vegetation period and the area where hydraulic facilities are located. Therefore, it is important to maintain trash racks clean by regular removal of the accumulated material. In this context, modernised and newly built power plants are fitted with mechanical cleaners. In older facilities, manual intervention for regular cleaning is required. The present study analyses how the bar shape and the orientation angle of trash racks as well as the accumulated plant debris affect head losses. The results were obtained from laboratory tests. The research examined the impact the inclination angle of trash racks (30°, 60° and 80° has on head loss values for three different shapes of bars (cylindrical, angled and flat rectangular and various weight portions of plant debris (0.25, 0.375 and 0.5 kg. The summarised losses were determined by measuring the difference in water

White House Communications Agency (WHCA) Presidential Voice Communications Rack Mount System Mechanical Drawing Package

Science.gov (United States)

2015-12-01

Rack Mount System Mechanical Drawing Package by Steven P Callaway Approved for public release; distribution unlimited...Laboratory White House Communications Agency (WHCA) Presidential Voice Communications Rack Mount System Mechanical Drawing Package by Steven P...Note 3. DATES COVERED (From - To) 04/2013 4. TITLE AND SUBTITLE White House Communications Agency (WHCA) Presidential Voice Communications Rack

A new electronic circuit for NIM rack power supply

International Nuclear Information System (INIS)

Toledo, Fabio de; Domienikan, Claudio; Zahn, Guilherme S.

2013-01-01

A new and useful electronic circuit designed to substitute the old power supply of IPEN model PM 1212 Nuclear Instrument Modules (NIM) racks is presented. Originally, these NIM racks were projected by IPEN workshop at 1974 to be used in nuclear research laboratories. The PM1212 provided mounting space and power sources for up to 12 standard nuclear electronic modules and power supply regulated DC voltages of ±24V (2A), ±12V (4A) and unregulated AC 117V (0.5A). Currently, several of these NIM racks are not in use because the electronic components of the original design have become obsolete and are no longer manufactured. The new electronic circuit provides the same original voltages adjusted in the single circuit and, additionally, ±6V. The new power supply was designed and constructed at IPEN-CNEN/SP by employing modern national components and expertise. (author)

A new electronic circuit for NIM rack power supply

Energy Technology Data Exchange (ETDEWEB)

Toledo, Fabio de; Domienikan, Claudio; Zahn, Guilherme S., E-mail: fatoledo@ipen.br, E-mail: clanikan@ipen.br, E-mail: gzahn@ipen.br [Intituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN/SP), Sao Paulo, SP (Brazil)

2013-07-01

A new and useful electronic circuit designed to substitute the old power supply of IPEN model PM 1212 Nuclear Instrument Modules (NIM) racks is presented. Originally, these NIM racks were projected by IPEN workshop at 1974 to be used in nuclear research laboratories. The PM1212 provided mounting space and power sources for up to 12 standard nuclear electronic modules and power supply regulated DC voltages of ±24V (2A), ±12V (4A) and unregulated AC 117V (0.5A). Currently, several of these NIM racks are not in use because the electronic components of the original design have become obsolete and are no longer manufactured. The new electronic circuit provides the same original voltages adjusted in the single circuit and, additionally, ±6V. The new power supply was designed and constructed at IPEN-CNEN/SP by employing modern national components and expertise. (author)

Anne Fine

Directory of Open Access Journals (Sweden)

Philip Gaydon

2015-04-01

Full Text Available An interview with Anne Fine with an introduction and aside on the role of children’s literature in our lives and development, and our adult perceptions of the suitability of childhood reading material. Since graduating from Warwick in 1968 with a BA in Politics and History, Anne Fine has written over fifty books for children and eight for adults, won the Carnegie Medal twice (for Goggle-Eyes in 1989 and Flour Babies in 1992, been a highly commended runner-up three times (for Bill’s New Frock in 1989, The Tulip Touch in 1996, and Up on Cloud Nine in 2002, been shortlisted for the Hans Christian Andersen Award (the highest recognition available to a writer or illustrator of children’s books, 1998, undertaken the positon of Children’s Laureate (2001-2003, and been awarded an OBE for her services to literature (2003. Warwick presented Fine with an Honorary Doctorate in 2005. Philip Gaydon’s interview with Anne Fine was recorded as part of the ‘Voices of the University’ oral history project, co-ordinated by Warwick’s Institute of Advanced Study.

A Study on Criticality Safety Parameters of New Fuel Storage Rack Design

International Nuclear Information System (INIS)

Ahn, Joon Gi; Kim, Hyeong Heon

2012-01-01

The dry new fuel storage rack shall maintain the subcritical condition (i.e., k-eff < 0.95) when fully flooded with water and the k-eff will not exceed 0.98 even assuming that the optimum moderation causes the highest reactivity. Thus, the design parameters of the new fuel rack are determined optimally by considering both the full density water flooding condition and the optimum moderation condition. The behavior of the keff as the variation of design parameter of the new fuel rack was investigated as the function of the moderating water density

A Study on Criticality Safety Parameters of New Fuel Storage Rack Design

Energy Technology Data Exchange (ETDEWEB)

Ahn, Joon Gi; Kim, Hyeong Heon [KEPCO E and C, Daejeon (Korea, Republic of)

2012-05-15

The dry new fuel storage rack shall maintain the subcritical condition (i.e., k-eff < 0.95) when fully flooded with water and the k-eff will not exceed 0.98 even assuming that the optimum moderation causes the highest reactivity. Thus, the design parameters of the new fuel rack are determined optimally by considering both the full density water flooding condition and the optimum moderation condition. The behavior of the keff as the variation of design parameter of the new fuel rack was investigated as the function of the moderating water density

Melting of fuel element racks and their recycling as granulate

International Nuclear Information System (INIS)

Quade, U.; Kluth, T.; Kreh, R.

1998-01-01

In order to increase the storage capacity for spent fuel elements in the Spanish NPPs of Almaraz and Asco, the existing racks were replaced by compact one in 1991/1993. The 28 racks from Almaraz NPP were cut on site, packed in 200-I-drums and taken to intermediate storage. For the remaining 28 racks of Asco NPP, ENRESA preferred the melting alternative. To demonstrate the recycling path melting in Germany, a test campaign with six racks was performed in 1997. As a result of this test melt, the limits for Carla melting plant were modified to 200 Bq/g total, α, β, γ 100 Bq/g nuclear fuels, max. 3g/100 kg 2,000 Bq/g total Fe55, H 3 , C-14 and Ni63. After the test melt campaign, the German authorities licensed the import and treatment of the remaining 22 racks on the condition that the waste resulting from the melting process as well as the granules produced were taken back to Spain. The shipment from Asco via France to Germany has been carried out in F 20-ft-IPII containers in accordance with ADR. Size reduction to chargeable dimensions was carried out by a plasma burner and hydraulic shears. For melting, a 3.2 Mg medium frequency induction furnace, operated in a separate housing, was used. For granules production outside this housing, the liquid iron was cast into a 5Mg ladle and then, through a water jet, into the granulating basin. The total mass of 287,659 Kg of 28 fuel elements racks and components of the storage basin yielded 297,914 kg of iron granulate. Secondary waste from melting amounted to 9,920 kg, corresponding to 3.45% of the input mass. The granulating process produced 6,589 kg, corresponding to 2.28% of the total mass to be melted. Radiological analysis of samples taken from the melt and different waste components confirmed the main nuclides Co60, Cs134 and Cs137. Fe55 was highly overestimated by the preliminary analysis. (Author) 2 refs

Ann Tenno salapaigad / Margit Tõnson

Index Scriptorium Estoniae

Tõnson, Margit, 1978-

2011-01-01

Fotograaf Ann Tenno aiandushuvist, pildistamisest maailma erinevates paikades. Uutest suundadest (fototöötlus, fractal art, soojuskaameraga pildistamine) tema loomingus. Katkendeid Ann Tenno 2010. aastal ilmunud proosaraamatust "Üle unepiiri"

26 CFR 48.4081-2 - Taxable fuel; tax on removal at a terminal rack.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 16 2010-04-01 2010-04-01 true Taxable fuel; tax on removal at a terminal rack..., Tread Rubber, and Taxable Fuel Taxable Fuel § 48.4081-2 Taxable fuel; tax on removal at a terminal rack... rack are subject to tax and the position holder with respect to the fuel is liable for the tax. (b...

40 CFR Table 2 to Subpart Bbbbbb... - Applicability Criteria, Emission Limits, and Management Practices for Loading Racks

Science.gov (United States)

2010-07-01

... Limits, and Management Practices for Loading Racks 2 Table 2 to Subpart BBBBBB of Part 63 Protection of... Criteria, Emission Limits, and Management Practices for Loading Racks If you own or operate Then you must 1. A gasoline loading rack(s) at a bulk gasoline terminal with a gasoline throughput of 250,000 gallons...

Surveillance of a Ventilated Rack System for Corynebacterium bovis by Sampling Exhaust-Air Manifolds.

Science.gov (United States)

Manuel, Christopher A; Pugazhenthi, Umarani; Leszczynski, Jori K

2016-01-01

Corynebacterium bovis causes an opportunistic infection of nude (Foxn1, nu/nu) mice, leading to nude mouse hyperkeratotic dermatitis (scaly skin disease). Enzootic in many nude mouse colonies, C. bovis spreads rapidly to naive nude mice, despite modern husbandry practices, and is very difficult to eradicate. To facilitate rapid detection in support of eradication efforts, we investigated a surveillance method based on quantitative real-time PCR (qPCR) evaluation of swabs collected from the horizontal exhaust manifold (HEM) of an IVC rack system. We first evaluated the efficacy of rack sanitation methods for removing C. bovis DNA from the HEM of racks housing endemic colonies of infected nude mice. Pressurized water used to flush the racks' air exhaust system followed by a standard rack-washer cycle was ineffective in eliminating C. bovis DNA. Only after autoclaving did all sanitized racks test negative for C. bovis DNA. We then measured the effects of stage of infection (early or established), cage density, and cage location on the rack on time-to-detection at the HEM. Stage of infection significantly affected time-to-detection, independent of cage location. Early infections required 7.3 ± 1.2 d whereas established infections required 1 ± 0 d for detection of C. bovis at the HEM. Cage density influenced the quantity of C. bovis DNA detected but not time-to-detection. The location of the cage on the rack affected the time-to-detection only during early C. bovis infections. We suggest that qPCR swabs of HEM are useful during the routine surveillance of nude mouse colonies for C. bovis infection.

Depletion of WRN protein causes RACK1 to activate several protein kinase C isoforms

DEFF Research Database (Denmark)

Massip, L; Garand, C; Labbé, A

2010-01-01

show that a knock down of the WRN protein in normal human fibroblasts induces phosphorylation and activation of several protein kinase C (PKC) enzymes. Using a tandem affinity purification strategy, we found that WRN physically and functionally interacts with receptor for activated C-kinase 1 (RACK1......), a highly conserved anchoring protein involved in various biological processes, such as cell growth and proliferation. RACK1 binds strongly to the RQC domain of WRN and weakly to its acidic repeat region. Purified RACK1 has no impact on the helicase activity of WRN, but selectively inhibits WRN exonuclease...... activity in vitro. Interestingly, knocking down RACK1 increased the cellular frequency of DNA breaks. Depletion of the WRN protein in return caused a fraction of nuclear RACK1 to translocate out of the nucleus to bind and activate PKCdelta and PKCbetaII in the membrane fraction of cells. In contrast...

Combined Cycle Engine Large-Scale Inlet for Mode Transition Experiments: System Identification Rack Hardware Design

Science.gov (United States)

Thomas, Randy; Stueber, Thomas J.

2013-01-01

The System Identification (SysID) Rack is a real-time hardware-in-the-loop data acquisition (DAQ) and control instrument rack that was designed and built to support inlet testing in the NASA Glenn Research Center 10- by 10-Foot Supersonic Wind Tunnel. This instrument rack is used to support experiments on the Combined-Cycle Engine Large-Scale Inlet for Mode Transition Experiment (CCE? LIMX). The CCE?LIMX is a testbed for an integrated dual flow-path inlet configuration with the two flow paths in an over-and-under arrangement such that the high-speed flow path is located below the lowspeed flow path. The CCE?LIMX includes multiple actuators that are designed to redirect airflow from one flow path to the other; this action is referred to as "inlet mode transition." Multiple phases of experiments have been planned to support research that investigates inlet mode transition: inlet characterization (Phase-1) and system identification (Phase-2). The SysID Rack hardware design met the following requirements to support Phase-1 and Phase-2 experiments: safely and effectively move multiple actuators individually or synchronously; sample and save effector control and position sensor feedback signals; automate control of actuator positioning based on a mode transition schedule; sample and save pressure sensor signals; and perform DAQ and control processes operating at 2.5 KHz. This document describes the hardware components used to build the SysID Rack including their function, specifications, and system interface. Furthermore, provided in this document are a SysID Rack effectors signal list (signal flow); system identification experiment setup; illustrations indicating a typical SysID Rack experiment; and a SysID Rack performance overview for Phase-1 and Phase-2 experiments. The SysID Rack described in this document was a useful tool to meet the project objectives.

ISS Payload Racks Automated Flow Control Calibration Method

Science.gov (United States)

Simmonds, Boris G.

2003-01-01

Payload Racks utilize MTL and/or LTL station water for cooling of payloads and avionics. Flow control range from valves of fully closed, to up to 300 Ibmhr. Instrument accuracies are as high as f 7.5 Ibm/hr for flow sensors and f 3 Ibm/hr for valve controller, for a total system accuracy of f 10.5 Ibm/hr. Improved methodology was developed, tested and proven that reduces accuracy of the commanded flows to less than f 1 Ibmhr. Uethodology could be packed in a "calibration kit" for on- orbit flow sensor checkout and recalibration, extending the rack operations before return to earth. -

78 FR 54450 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

Science.gov (United States)

2013-09-04

... Shelving and Racks From the People's Republic of China: Preliminary Results of Antidumping Duty... the antidumping duty order on certain kitchen appliance shelving and racks from the People's Republic...\\ is certain kitchen appliance shelving and racks. The subject merchandise is currently classifiable...

The fabrication of plastic cages for suspension in mass air flow racks.

Science.gov (United States)

Nielsen, F H; Bailey, B

1979-08-01

A cage for suspension in mass air flow racks was constructed of plastic and used to house rats. Little or no difficulty was encountered with the mass air flow rack-suspended cage system during the 4 years it was used for the study of trace elements.

The ISS Fluids Integrated Rack (FIR): a Summary of Capabilities

Science.gov (United States)

Gati, F.; Hill, M. E.

2002-01-01

The Fluids Integrated Rack (FIR) is a modular, multi-user scientific research facility that will fly in the U.S. laboratory module, Destiny, of the International Space Station (ISS). The FIR will be one of the two racks that will make up the Fluids and Combustion Facility (FCF) - the other being the Combustion Integrated Rack (CIR). The ISS will provide the FCF with the necessary resources, such as power and cooling. While the ISS crew will be available for experiment operations, their time will be limited. The FCF is, therefore, being designed for autonomous operations and remote control operations. Control of the FCF will be primarily through the Telescience Support Center (TSC) at the Glenn Research Center. The FCF is being designed to accommodate a wide range of combustion and fluids physics experiments within the ISS resources and constraints. The primary mission of the FIR, however, is to accommodate experiments from four major fluids physics disciplines: Complex Fluids; Multiphase Flow and Heat Transfer; Interfacial Phenomena; and Dynamics and Stability. The design of the FIR is flexible enough to accommodate experiments from other science disciplines such as Biotechnology. The FIR flexibility is a result of the large volume dedicated for experimental hardware, easily re-configurable diagnostics that allow for unique experiment configurations, and it's customizable software. The FIR will utilize six major subsystems to accommodate this broad scope of fluids physics experiments. The major subsystems are: structural, environmental, electrical, gaseous, command and data management, and imagers and illumination. Within the rack, the FIR's structural subsystem provides an optics bench type mechanical interface for the precise mounting of experimental hardware; including optical components. The back of the bench is populated with FIR avionics packages and light sources. The interior of the rack is isolated from the cabin through two rack doors that are hinged near

77 FR 72324 - Certain Kitchen Appliance Shelving and Racks from the People's Republic of China: Countervailing...

Science.gov (United States)

2012-12-05

... Shelving and Racks from the People's Republic of China: Countervailing Duty Administrative Review, 2010... countervailing duty order on certain kitchen appliance shelving and racks from the People's Republic of China. See Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Countervailing...

Kale BoRACK1 is involved in the plant response to salt stress and Peronospora brassicae Gaumann.

Science.gov (United States)

Li, Da-Hong; Shen, Fu-Jia; Li, Hong-Yan; Li, Wei

2017-06-01

The receptor for activated C kinase 1 (RACK1) belongs to a protein subfamily containing a tryptophan-aspartic acid-domain (WD) repeat structure. Compelling evidence indicates that RACK1 can interact with many signal molecules and affect different signal transduction pathways. In this study, a kale (Brassica oleracea var. acephala f.tricolor) RACK1 gene (BoRACK1) was cloned by RT-PCR. The amino acid sequence of BoRACK1 had seven WD repeats in which there were typical GH (glycine-histidine) and WD dipeptides. Comparison with AtRACK1 from Arabidopsis revealed 87.1% identity at the amino acid level. Expression pattern analysis by RT-PCR showed that BoRACK1 was expressed in all analyzed tissues of kale and that its transcription in leaves was down-regulated by salt, abscisic acid, and H 2 O 2 at a high concentration. Overexpression of BoRACK1 in kale led to a reduction in symptoms caused by Peronospora brassicae Gaumann on kale leaves. The expression levels of the pathogenesis-related protein genes, PR-1 and PRB-1, increased 2.5-4-fold in transgenic kale, and reactive oxygen species production was more active than in the wild-type. They also exhibited increased tolerance to salt stress in seed germination. H 2 O 2 may also be involved in the regulation of BoRACK1 during seed germination under salt stress. Quantitative real-time PCR analyses showed that the transcript levels of BoRbohs genes were significantly higher in overexpression of BoRACK1 transgenic lines. Yeast two-hybrid assays showed that BoRACK1 could interact with WNK8, eIF6, RAR1, and SGT1. This study and previous work lead us to believe that BoRACK1 may form a complex with regulators of plant salt and disease resistance to coordinate kale reactions to pathogens. Copyright © 2017 Elsevier GmbH. All rights reserved.

Annely Peebo kutsus presidendi kontserdile / Maria Ulfsak

Index Scriptorium Estoniae

Ulfsak, Maria, 1981-

2003-01-01

Laulja Anneli Peebo kohtus president Arnold Rüütliga, et anda üle kutse Andrea Bocelli ja Annely Peebo ühiskontserdile. Vt. samas: Andrea Bocelli ja Annely Peebo kontsert Tallinna lauluväljakul 23. augustil; Andrea Bocelli

77 FR 61385 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Antidumping...

Science.gov (United States)

2012-10-09

... Shelving and Racks From the People's Republic of China: Antidumping Duty Administrative Review, 2010-2011... administrative review of the antidumping duty order on certain kitchen appliance shelving and racks from the... INFORMATION: Scope of the Order The scope of this order consists of shelving and racks for refrigerators...

77 FR 12811 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Partial...

Science.gov (United States)

2012-03-02

... Shelving and Racks From the People's Republic of China: Partial Rescission of Antidumping Duty... review of the antidumping duty order on certain kitchen appliance shelving and racks from the People's... Appliance Shelving and Racks from the People's Republic of China, dated January 10, 2012; and Letter to the...

76 FR 62765 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

Science.gov (United States)

2011-10-11

... Shelving and Racks From the People's Republic of China: Preliminary Results of the First Administrative... review of the antidumping duty order on certain kitchen appliance shelving and racks from the People's... administrative review of certain kitchen appliance shelving and racks from the PRC for the period March 5, 2009...

26 CFR 48.4081-3 - Taxable fuel; taxable events other than removal at the terminal rack.

Science.gov (United States)

2010-04-01

... at the terminal rack. 48.4081-3 Section 48.4081-3 Internal Revenue INTERNAL REVENUE SERVICE...; taxable events other than removal at the terminal rack. (a) Overview. Although tax is imposed when taxable fuel is removed from the terminal at the rack, tax also is imposed in certain other situations...

16 CFR Figure 3 to Part 1610 - Specimen Holder Supported in Specimen Rack

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Specimen Holder Supported in Specimen Rack 3 Figure 3 to Part 1610 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT... Holder Supported in Specimen Rack ER25MR08.002 ...

IFBA credit in the Shearon Harris fuel racks with Vantage 5 fuel

International Nuclear Information System (INIS)

Boyd, W.A.; Schmidt, R.F.; Erwin, R.D.

1989-01-01

At the Shearon Harris nuclear plant, fuel management strategies are being considered which will result in feed fuel enrichments approaching 5.0 w/o U-235. These types of enrichments require a new criticality analysis to raise the existing fuel rack enrichment limit. It is receiving Westinghouse Vantage 5 fuel with integral fuel burnable absorber (IFBA) rods providing the depletable neutron absorber. An analysis was performed on the fuel racks which demonstrates that fuel enriched up to 5.0 w/o U-235 can be stored by taking credit for the IFBA rods present in the high enriched fuel assemblies. This is done by calculating the maximum Vantage 5 fuel assembly reactivity that can be placed in the fuel racks and meet the criticality K-eff limit. A methodology is also developed which conservatively calculates the minimum number of IFBA rods needed per assembly to meet the fuel rack storage limits. This eliminates the need for core designers to determine assembly K-inf terms for every different enrichment/IFBA combination

Tests and calculations on a scale one spent fuel storage rack

International Nuclear Information System (INIS)

Moudrik, R.; Queval, J.C.; Gantenbein, F.; Trollat, C.

1995-01-01

This paper deals with the behaviour of racks of PWR reactor (pressurized water reactor) set in a pool, in case of an earthquake. Several parameters are taken into account: fluid, loading, gaps,... The paper presents some tests that can be implemented on the racks, in order to valid them before use. Moreover, a program and the results are presented, as well as calculation. (TEC). 2 refs., 9 figs

Criticality and Its Uncertainty Analysis of Spent Fuel Storage Rack for Research Reactor

International Nuclear Information System (INIS)

Han, Tae Young; Park, Chang Je; Lee, Byung Chul

2011-01-01

For evaluating the criticality safety of spent fuel storage rack in an open pool type research reactor, a permissible upper limit of criticality should be determined. It can be estimated from the criticality upper limit presented by the regulatory guide and an uncertainty of criticality calculation. In this paper, criticalities for spent fuel storage rack are carried out at various conditions. The calculation uncertainty of MCNP system is evaluated from the calculation results for the benchmark experiments. Then, the upper limit of criticality is determined from the uncertainties and the calculated criticality of the spent fuel storage rack is evaluated

MSRR Rack Materials Science Research Rack

Science.gov (United States)

Reagan, Shawn

2017-01-01

The Materials Science Research Rack (MSRR) is a research facility developed under a cooperative research agreement between NASA and the European Space Agency (ESA) for materials science investigations on the International Space Station (ISS). The MSRR is managed at the Marshall Space Flight Center (MSFC) in Huntsville, AL. The MSRR facility subsystems were manufactured by Teledyne Brown Engineering (TBE) and integrated with the ESA/EADS-Astrium developed Materials Science Laboratory (MSL) at the MSFC Space Station Integration and Test Facility (SSITF) as part of the Systems Development Operations Support (SDOS) contract. MSRR was launched on STS-128 in August 2009, and is currently installed in the U. S. Destiny Laboratory Module on the ISS. Materials science is an integral part of developing new, safer, stronger, more durable materials for use throughout everyday life. The goal of studying materials processing in space is to develop a better understanding of the chemical and physical mechanisms involved, and how they differ in the microgravity environment of space. To that end, the MSRR accommodates advanced investigations in the microgravity environment of the ISS for basic materials science research in areas such as solidification of metals and alloys. MSRR allows for the study of a variety of materials including metals, ceramics, semiconductor crystals, and glasses. Materials science research benefits from the microgravity environment of space, where the researcher can better isolate chemical and thermal properties of materials from the effects of gravity. With this knowledge, reliable predictions can be made about the conditions required on Earth to achieve improved materials. MSRR is a highly automated facility with a modular design capable of supporting multiple types of investigations. Currently the NASA-provided Rack Support Subsystem provides services (power, thermal control, vacuum access, and command and data handling) to the ESA developed Materials

78 FR 21594 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Final Results...

Science.gov (United States)

2013-04-11

... Shelving and Racks From the People's Republic of China: Final Results of Countervailing Duty Administrative... countervailing duty (``CVD'') order on certain kitchen appliance shelving and racks from the People's Republic of...\\ See Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Countervailing...

78 FR 78815 - Certain Kitchen Appliance Shelving and Racks from the People's Republic of China: Rescission of...

Science.gov (United States)

2013-12-27

... Shelving and Racks from the People's Republic of China: Rescission of Antidumping Duty Administrative... administrative review of the antidumping duty order on certain kitchen appliance shelving and racks from the... on certain kitchen appliance shelving and racks from the PRC.\\1\\ On September 30, 2013, the...

77 FR 21734 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Final Results...

Science.gov (United States)

2012-04-11

... Shelving and Racks From the People's Republic of China: Final Results and Partial Rescission of First... duty order on certain kitchen appliance shelving and racks from the People's Republic of China (``PRC... Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary Results of...

Dioxin modulates expression of receptor for activated C kinase (RACK-1) in developing neurons

Energy Technology Data Exchange (ETDEWEB)

Yang, J.H.; Kim, S.Y.; Lee, H.G.; Kim, M.Y.; Lee, J.H.; Chae, W.G. [Catholic Univ. of Daegu, Dept. of Pharmacology/Toxicology, Daegu (Korea)

2004-09-15

TCDD is sensitive to the central nerve system of the developing brain. The TCDD-induced neurodevelopmental deficits include the cognitive disability and motor dysfunction. While TCDD may lead to neurodevelopmental and neurobehavioral deficit, it is not known which molecular substances are intracellular targets for TCDD. Since TCDD accumulates in brain and the brain contains the Ah receptor, it is possible that TCDD may act at the target site such as cerebellum, which is responsible for cognitive abilities and motor function. A recent in vitro studies using cerebellar granule cells demonstrated a translocation of PKC-{alpha} and {epsilon} following the TCDD or PCB exposure. One of the most pivotal second messenger molecules involved in neuronal function and development is protein kinase C (PKC). PKC signaling pathways have been implicated as an important factor in learning and memory processes. PKC signaling events are optimized by the adaptor proteins, which organize PKCs near their selective substrates and away from others. RACK-1(receptor for activated C-kinase) is one of adaptor proteins that anchor the activated PKC at the site of translocation 6. RACKs bind PKC only in the presence of PKC activators. RACKs are 30- and 36-kDa proteins located in cytoskeletal compartment and play a key role in PKC activation and in membrane amchoring. Since different PKC isoforms translocate to distinct subcellular sites on activation, it is suggested that isoform-specific RACK may be present. Activation of certain PKC isoforms (PKC-a and {beta}II) is preferentially associated with RACK-1. While TCDD modulates PKC signaling pathway, role of RACK-1 on TCDD-mediated signaling pathway is not known. To identify the intracellular target for TCDD and understand a mechanism of signaling pathway in the developing brain, the present study attempted to analyze effects of RACK-1 in the cerebellar granule cells following TCDD exposure.

77 FR 82 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Extension of...

Science.gov (United States)

2012-01-03

... Shelving and Racks From the People's Republic of China: Extension of Time Limit for the Final Results of... administrative review of the countervailing duty order on certain kitchen appliance shelving and racks from the... Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary Results of the...

78 FR 5414 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China; 2010-2011...

Science.gov (United States)

2013-01-25

... Shelving and Racks From the People's Republic of China; 2010-2011; Final Results of Antidumping Duty... of the antidumping duty order on certain kitchen appliance shelving and racks from the People's... September 1, 2010, through August 31, 2011. \\1\\ See Certain Kitchen Appliance Shelving and Racks From the...

77 FR 22559 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Extension of...

Science.gov (United States)

2012-04-16

... Shelving and Racks From the People's Republic of China: Extension of Time Limit for the Preliminary Results... administrative review of the antidumping duty order on certain kitchen appliance shelving and racks from the... Appliance Shelving and Racks from the People's Republic of China: Selection of an Additional Mandatory...

76 FR 20950 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Extension of...

Science.gov (United States)

2011-04-14

... Shelving and Racks From the People's Republic of China: Extension of Time Limits for the Preliminary... appliance shelving and racks from the People's Republic of China (``PRC'') for the period March 5, 2009... Racks from the People's Republic of China,'' dated January 20, 2011. The Department sent its antidumping...

Definition of a RACK1 Interaction Network in Drosophila melanogaster Using SWATH-MS.

Science.gov (United States)

Kuhn, Lauriane; Majzoub, Karim; Einhorn, Evelyne; Chicher, Johana; Pompon, Julien; Imler, Jean-Luc; Hammann, Philippe; Meignin, Carine

2017-07-05

Receptor for Activated protein C kinase 1 (RACK1) is a scaffold protein that has been found in association with several signaling complexes, and with the 40S subunit of the ribosome. Using the model organism Drosophila melanogaster , we recently showed that RACK1 is required at the ribosome for internal ribosome entry site (IRES)-mediated translation of viruses. Here, we report a proteomic characterization of the interactome of RACK1 in Drosophila S2 cells. We carried out Label-Free quantitation using both Data-Dependent and Data-Independent Acquisition (DDA and DIA, respectively) and observed a significant advantage for the Sequential Window Acquisition of all THeoretical fragment-ion spectra (SWATH) method, both in terms of identification of interactants and quantification of low abundance proteins. These data represent the first SWATH spectral library available for Drosophila and will be a useful resource for the community. A total of 52 interacting proteins were identified, including several molecules involved in translation such as structural components of the ribosome, factors regulating translation initiation or elongation, and RNA binding proteins. Among these 52 proteins, 15 were identified as partners by the SWATH strategy only. Interestingly, these 15 proteins are significantly enriched for the functions translation and nucleic acid binding. This enrichment reflects the engagement of RACK1 at the ribosome and highlights the added value of SWATH analysis. A functional screen did not reveal any protein sharing the interesting properties of RACK1, which is required for IRES-dependent translation and not essential for cell viability. Intriguingly however, 10 of the RACK1 partners identified restrict replication of Cricket paralysis virus (CrPV), an IRES-containing virus. Copyright © 2017 Kuhn et al.

40 CFR Table 5 to Subpart Ffff of... - Emission Limits and Work Practice Standards for Transfer Racks

Science.gov (United States)

2010-07-01

... Standards for Transfer Racks 5 Table 5 to Subpart FFFF of Part 63 Protection of Environment ENVIRONMENTAL... Limits and Work Practice Standards for Transfer Racks As required in § 63.2475, you must meet each emission limit and work practice standard in the following table that applies to your transfer racks: For...

Implications of natural occlusion of ventilated racks on ammonia and sanitation practices.

Science.gov (United States)

Creamer, Michelle A; Petty, Joann; Martin, Tara; Bergdall, Valerie; Hickman-Davis, Judy M

2014-03-01

Examination of ventilated rat racks prior to semiannual sanitation revealed silicone nozzles and ventilation ports that were partially or completely occluded with granular debris. We subsequently sought to document performance standards for rack sanitation and investigate the effect of ventilation port occlusion on rack function and animal husbandry practices. We hypothesized that individually ventilated cages with occluded airflow would require more frequent cage changes, comparable to those for static cages (that is, every 3 to 4 d). Sprague-Dawley rats were housed under one of 4 conditions: no airflow occlusion, occluded air-supply inlet, occluded air-exhaust outlet, and occlusion of both inlet and outlet. Cages were changed when daily ammonia concentration exceeded 20 ppm or after 14 d had elapsed. Most cages with unoccluded or partial airflow occlusion remained below the 20 ppm limit until day 12 or 13. Cages with occlusion of both inlet and outlet exceeded 20 ppm ammonia by as early as day 5. Airflow was significantly lower in cages with occlusion of both inlet and outlet airflow. Weekly inspection revealed that occlusion of ventilation ports was detectable by 3 mo after semiannual sanitation. This study demonstrates that silicone nozzles should be removed prior to rack sanitation to improve the effectiveness of cleaning ventilation ports and nozzles. While the rack is in use, silicone nozzles and ventilation ports should be inspected regularly to identify occlusion that is likely to diminish environmental quality in the cage. Intracage ammonia levels are significantly higher when both inlet and outlet airflow are occluded.

76 FR 27990 - Certain Kitchen Shelving and Racks From the People's Republic of China: Extension of Time Limit...

Science.gov (United States)

2011-05-13

... Racks From the People's Republic of China: Extension of Time Limit for Preliminary Results of... countervailing duty order on certain kitchen appliance shelving and racks from the People's Republic of China... the Countervailing Duty Administrative Review of Certain Kitchen Appliance Shelving and Racks from the...

Super capacitor modeling with artificial neural network (ANN)

Energy Technology Data Exchange (ETDEWEB)

Marie-Francoise, J.N.; Gualous, H.; Berthon, A. [Universite de Franche-Comte, Lab. en Electronique, Electrotechnique et Systemes (L2ES), UTBM, INRETS (LRE T31) 90 - Belfort (France)

2004-07-01

This paper presents super-capacitors modeling using Artificial Neural Network (ANN). The principle consists on a black box nonlinear multiple inputs single output (MISO) model. The system inputs are temperature and current, the output is the super-capacitor voltage. The learning and the validation of the ANN model from experimental charge and discharge of super-capacitor establish the relationship between inputs and output. The learning and the validation of the ANN model use experimental results of 2700 F, 3700 F and a super-capacitor pack. Once the network is trained, the ANN model can predict the super-capacitor behaviour with temperature variations. The update parameters of the ANN model are performed thanks to Levenberg-Marquardt method in order to minimize the error between the output of the system and the predicted output. The obtained results with the ANN model of super-capacitor and experimental ones are in good agreement. (authors)

TCR triggering induces the formation of Lck-RACK1-actinin-1 multiprotein network affecting Lck redistribution

Directory of Open Access Journals (Sweden)

Ondrej Ballek

2016-10-01

Full Text Available The initiation of T-cell signaling is critically dependent on the function of the member of Src family tyrosine kinases (SFKs, Lck. Upon TCR triggering, Lck kinase activity induces the nucleation of signal-transducing hubs that regulate the formation of complex signaling network and cytoskeletal rearrangement. In addition, the delivery of Lck function requires rapid and targeted membrane redistribution, but the mechanism underpinning this process is largely unknown. To gain insight into this process, we considered previously described proteins that could assist in this process via their capacity to interact with kinases and regulate their intracellular translocations. An adaptor protein, Receptor for Activated C Kinase 1 (RACK1, was chosen as a viable option and its capacity to bind Lck and aid the process of activation-induced redistribution of Lck was assessed. Our microscopic observation showed that T-cell activation induces a rapid, concomitant and transient co-redistribution of Lck and RACK1 into the forming immunological synapse. Consistent with this observation, the formation of transient RACK1-Lck complexes were detectable in primary CD4+ T-cells with their maximum levels peaking 10 seconds after TCR-CD4 co-aggregation. Moreover, RACK1 preferentially binds to a pool of kinase active pY394Lck which co-purifies with high molecular weight cellular fractions. The formation of RACK1-Lck complexes depends on functional SH2 and SH3 domains of Lck and includes several other signaling and cytoskeletal elements that transiently bind the complex. Notably, the F-actin-crosslinking protein, α-actinin-1, binds to RACK1 only in the presence of kinase active Lck suggesting that the formation of RACK1-pY394Lck-α-actinin-1 complex serves as a signal module coupling actin cytoskeleton bundling with productive TCR/CD4 triggering. In addition, the treatment of CD4+ T-cells with nocodazole, which disrupts the microtubular network, also blocked the formation

Test Rack Development for Extended Operation of Advanced Stirling Convertors at NASA Glenn Research Center

Science.gov (United States)

Dugala, Gina M.

2010-01-01

The U.S. Department of Energy, Lockheed Martin Space Systems Company, Sunpower Inc., and NASA Glenn Research Center (GRC) have been developing an Advanced Stirling Radioisotope Generator (ASRG) for use as a power system on space science missions. This generator will make use of free-piston Stirling convertors to achieve higher conversion efficiency than with currently available alternatives. One part of NASA GRC's support of ASRG development includes extended operation testing of Advanced Stirling Convertors (ASCs) developed by Sunpower Inc. and GRC. The ASC consists of a free-piston Stirling engine integrated with a linear alternator. NASA GRC has been building test facilities to support extended operation of the ASCs for several years. Operation of the convertors in the test facility provides convertor performance data over an extended period of time. One part of the test facility is the test rack, which provides a means for data collection, convertor control, and safe operation. Over the years, the test rack requirements have changed. The initial ASC test rack utilized an alternating-current (AC) bus for convertor control; the ASRG Engineering Unit (EU) test rack can operate with AC bus control or with an ASC Control Unit (ACU). A new test rack is being developed to support extended operation of the ASC-E2s with higher standards of documentation, component selection, and assembly practices. This paper discusses the differences among the ASC, ASRG EU, and ASC-E2 test racks.

Anne-Mette Langes plan for ADHD kongressen

DEFF Research Database (Denmark)

Lange, Anne-Mette

2017-01-01

http://medicinsktidsskrift.dk/behandlinger/psykiatri/699-anne-mette-langes-plan-for-adhd-kongressen.html......http://medicinsktidsskrift.dk/behandlinger/psykiatri/699-anne-mette-langes-plan-for-adhd-kongressen.html...

2011 : Qu'elle année !

CERN Multimedia

Staff Association

2012-01-01

« Quelle année ! Et quelle fin d’année ! La star de l’année a été le LHC, avec ses expériences, qui une fois de plus ont été sous les feux de la rampe. Mais on doit aussi citer toute une troupe d’acteurs importants, dans des domaines aussi différents que l’antimatière et l’expérience CLOUD. » Voilà ce que le Directeur général nous a écrit le 20 décembre dans son message avec ses vœux de fin d’année. Sans oublier, bien sûr, les fameux neutrinos hyperrapides vers Gran Sasso qui ont mis le CERN sur le devant de la scène mondiale. Ces succès qui font la fierté et la force de l’Organisation ont été rendus possibles «&...

Seismic evaluation of BWR spent fuel storage racks using actual damping by vibration test in water

International Nuclear Information System (INIS)

Yamasaki, Hiroto; Iwakura, Shigeyoshi; Imaoka, Tetsuo; Okumura, Kazue; Orita, Syuichi; Namita, Yoshio

2010-01-01

Damping value for BWR spent fuel storage racks has been used 1 percent damping, which is applied to welded steel structures in air as defined JEAG4601. However, it is considered that the actual damping is higher than that of the above mentioned, because of its underwater installation. This report shows the actual damping value of the Check Arrayed Rack by vibration test in water and Evaluation by the analysis of rack using actual damping. (author)

40 CFR Table 3 to Subpart Eeee of... - Operating Limits-High Throughput Transfer Racks

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits-High Throughput Transfer Racks 3 Table 3 to Subpart EEEE of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION... Throughput Transfer Racks As stated in § 63.2346(e), you must comply with the operating limits for existing...

Remote inspection of the IFSF spent fuel storage rack

International Nuclear Information System (INIS)

Uldrich, E.D.

1996-01-01

The Irradiated Fuel Storage Facility (IFSF) is a dry storage facility for spent nuclear fuels located at the Idaho Chemical Processing Plant; it was constructed in the 1970's specifically for the Fort Saint Vrain spent reactor fuels. Currently, it is being used for various spent fuels. It was not known if IFSF would met current DOE seismic criteria, so re-analysis was started, with the rack being analyzed first. The rack was inspected to determine the as-built condition. LazrLyne and VideoRuler were used in lieu of using a tape measure with the camera. It was concluded that when a visual inspection shows widely varying weld sizes, the engineer has to use all resources available to determine the most probable specified weld sizes

First Materials Science Research Facility Rack Capabilities and Design Features

Science.gov (United States)

Cobb, S.; Higgins, D.; Kitchens, L.; Curreri, Peter (Technical Monitor)

2002-01-01

The first Materials Science Research Rack (MSRR-1) is the primary facility for U.S. sponsored materials science research on the International Space Station. MSRR-1 is contained in an International Standard Payload Rack (ISPR) equipped with the Active Rack Isolation System (ARIS) for the best possible microgravity environment. MSRR-1 will accommodate dual Experiment Modules and provide simultaneous on-orbit processing operations capability. The first Experiment Module for the MSRR-1, the Materials Science Laboratory (MSL), is an international cooperative activity between NASA's Marshall Space Flight Center (MSFC) and the European Space Agency's (ESA) European Space Research and Technology Center (ESTEC). The MSL Experiment Module will accommodate several on-orbit exchangeable experiment-specific Module Inserts which provide distinct thermal processing capabilities. Module Inserts currently planned for the MSL are a Quench Module Insert, Low Gradient Furnace, and a Solidification with Quench Furnace. The second Experiment Module for the MSRR-1 configuration is a commercial device supplied by MSFC's Space Products Development (SPD) Group. Transparent furnace assemblies include capabilities for vapor transport processes and annealing of glass fiber preforms. This Experiment Module is replaceable on-orbit. This paper will describe facility capabilities, schedule to flight and research opportunities.

Feature Selection and ANN Solar Power Prediction

Directory of Open Access Journals (Sweden)

Daniel O’Leary

2017-01-01

Full Text Available A novel method of solar power forecasting for individuals and small businesses is developed in this paper based on machine learning, image processing, and acoustic classification techniques. Increases in the production of solar power at the consumer level require automated forecasting systems to minimize loss, cost, and environmental impact for homes and businesses that produce and consume power (prosumers. These new participants in the energy market, prosumers, require new artificial neural network (ANN performance tuning techniques to create accurate ANN forecasts. Input masking, an ANN tuning technique developed for acoustic signal classification and image edge detection, is applied to prosumer solar data to improve prosumer forecast accuracy over traditional macrogrid ANN performance tuning techniques. ANN inputs tailor time-of-day masking based on error clustering in the time domain. Results show an improvement in prediction to target correlation, the R2 value, lowering inaccuracy of sample predictions by 14.4%, with corresponding drops in mean average error of 5.37% and root mean squared error of 6.83%.

The scaffold protein RACK1 is a target of endocrine disrupting chemicals (EDCs) with important implication in immunity

Energy Technology Data Exchange (ETDEWEB)

Buoso, Erica; Galasso, Marilisa; Ronfani, Melania [Dipartimento di Scienze del Farmaco, Università degli Studi di Pavia, Viale Taramelli 12/14, 27100 Pavia (Italy); Papale, Angela; Galbiati, Valentina [Laboratory of Toxicology, Dipartimento di Scienze Farmacologiche e Biomolecolari, Università degli Studi di Milano, Via Balzaretti 9, 20133 Milano (Italy); Eberini, Ivano [Laboratorio di Biochimica e Biofisica Computazionale, Dipartimento di Scienze Farmacologiche e Biomolecolari, Università degli Studi di Milano, Milan (Italy); Marinovich, Marina [Laboratory of Toxicology, Dipartimento di Scienze Farmacologiche e Biomolecolari, Università degli Studi di Milano, Via Balzaretti 9, 20133 Milano (Italy); Racchi, Marco [Dipartimento di Scienze del Farmaco, Università degli Studi di Pavia, Viale Taramelli 12/14, 27100 Pavia (Italy); Corsini, Emanuela, E-mail: emanuela.corsini@unimi.it [Laboratory of Toxicology, Dipartimento di Scienze Farmacologiche e Biomolecolari, Università degli Studi di Milano, Via Balzaretti 9, 20133 Milano (Italy)

2017-06-15

We recently demonstrated the existence of a complex hormonal balance between steroid hormones in the control of RACK1 (Receptor for Activated C Kinase 1) expression and immune activation, suggesting that this scaffold protein may also be targeted by endocrine disrupting chemicals (EDCs). As a proof of concept, we investigated the effect of the doping agent nandrolone, an androgen receptor (AR) agonist, and of p,p′DDT (dichlorodiphenyltrichloroethane) and its main metabolite p,p′DDE (dichlorodiphenyldichloroethylene), a weak and strong AR antagonist, respectively, on RACK1 expression and innate immune response. In analogy to endogenous androgens, nandrolone induced a dose-related increase in RACK1 transcriptional activity and protein expression, resulting in increased LPS-induced IL-8 and TNF-α production and proliferation in THP-1 cells. Conversely, p,p′DDT and p,p′DDE significantly decrease RACK1 expression, LPS-induced cytokine production and CD86 expression; with p,p′DDE exerting a stronger repressor effect than p,p′DDT, consistent with its stronger AR antagonistic effect. These results indicate that RACK1 could be a relevant target of EDCs, responding in opposite ways to agonist or antagonist of AR, representing a bridge between the endocrine system and the innate immune system. - Highlights: • RACK1 expression can be induced by AR agonists with a consequent enhancement of the response to LPS. • RACK1 can be negatively modulated by the AR antagonists DDT and its main metabolite p,p′DDE. • RACK1 can be a relevant target of EDCs, representing a bridge between the endocrine system and the immune system.

Biogas engine performance estimation using ANN

Directory of Open Access Journals (Sweden)

Yusuf Kurtgoz

2017-12-01

Full Text Available Artificial neural network (ANN method was used to estimate the thermal efficiency (TE, brake specific fuel consumption (BSFC and volumetric efficiency (VE values of a biogas engine with spark ignition at different methane (CH4 ratios and engine load values. For this purpose, the biogas used in the biogas engine was produced by the anaerobic fermentation method from bovine manure and different CH4 contents (51%, 57%, 87% were obtained by purification of CO2 and H2S. The data used in the ANN models were obtained experimentally from a 4-stroke four-cylinder, spark ignition engine, at constant speed for different load and CH4 ratios. Using some of the obtained experimental data, ANN models were developed, and the rest was used to test the developed models. In the ANN models, the CH4 ratio of the fuel, engine load, inlet air temperature (Tin, air fuel ratio and the maximum cylinder pressure are chosen as the input parameters. TE, BSFC and VE are used as the output parameters. Root mean square error (RMSE, mean absolute percentage error (MAPE and correlation coefficient (R performance indicators are used to compare measured and predicted values. It has been shown that ANN models give good results in spark ignition biogas engines with high correlation and low error rates for TE, BSFC and VE values.

Carbon Dioxide Dispersion in the Combustion Integrated Rack Simulated Numerically

Science.gov (United States)

Wu, Ming-Shin; Ruff, Gary A.

2004-01-01

When discharged into an International Space Station (ISS) payload rack, a carbon dioxide (CO2) portable fire extinguisher (PFE) must extinguish a fire by decreasing the oxygen in the rack by 50 percent within 60 sec. The length of time needed for this oxygen reduction throughout the rack and the length of time that the CO2 concentration remains high enough to prevent the fire from reigniting is important when determining the effectiveness of the response and postfire procedures. Furthermore, in the absence of gravity, the local flow velocity can make the difference between a fire that spreads rapidly and one that self-extinguishes after ignition. A numerical simulation of the discharge of CO2 from PFE into the Combustion Integrated Rack (CIR) in microgravity was performed to obtain the local velocity and CO2 concentration. The complicated flow field around the PFE nozzle exits was modeled by sources of equivalent mass and momentum flux at a location downstream of the nozzle. The time for the concentration of CO2 to reach a level that would extinguish a fire anywhere in the rack was determined using the Fire Dynamics Simulator (FDS), a computational fluid dynamics code developed by the National Institute of Standards and Technology specifically to evaluate the development of a fire and smoke transport. The simulation shows that CO2, as well as any smoke and combustion gases produced by a fire, would be discharged into the ISS cabin through the resource utility panel at the bottom of the rack. These simulations will be validated by comparing the results with velocity and CO2 concentration measurements obtained during the fire suppression system verification tests conducted on the CIR in March 2003. Once these numerical simulations are validated, portions of the ISS labs and living areas will be modeled to determine the local flow conditions before, during, and after a fire event. These simulations can yield specific information about how long it takes for smoke and

Obituary: Anne Barbara Underhill, 1920-2003

Science.gov (United States)

Roman, Nancy Grace

2003-12-01

Anne was born in Vancouver, British Columbia on 12 June 1920. Her parents were Frederic Clare Underhill, a civil engineer and Irene Anna (née Creery) Underhill. She had a twin brother and three younger brothers. As a young girl she was active in Girl Guides and graduated from high school winning the Lieutenant Governor's medal as one of the top students in the Province. She also excelled in high school sports. Her mother died when Anne was 18 and, while undertaking her university studies, Anne assisted in raising her younger brothers. Her twin brother was killed in Italy during World War II (1944), a loss that Anne felt deeply. Possibly because of fighting to get ahead in astronomy, a field overwhelming male when she started, she frequently appeared combative. At the University of British Columbia, Anne obtained a BA (honors) in Chemistry (1942), followed by a MA in 1944. After working for the NRC in Montreal for a year, she studied at the University of Toronto prior to entering the University of Chicago in 1946 to obtain her PhD. Her thesis was the first model computed for a multi-layered stellar atmosphere (1948). During this time she worked with Otto Struve, developing a lifetime interest in hot stars and the analysis of their high dispersion spectra. She received two fellowships from the University Women of Canada. She received a U.S. National Research Fellowship to work at the Copenhagen Observatory, and upon its completion, she returned to British Columbia to work at the Dominion Astrophysical Observatory as a research scientist from 1949--1962. During this period she spent a year at Harvard University as a visiting professor and at Princeton where she used their advanced computer to write the first code for modeling stellar atmospheres. Anne was invited to the University of Utrecht (Netherlands) as a full professor in 1962. She was an excellent teacher, well liked by the students in her classes, and by the many individuals that she guided throughout her

Evaluation of food storage racks available on the Polish market in the hygienic context

Science.gov (United States)

Grzesińska, Wiesława; Tomaszewska, Marzena; Bilska, Beata; Trafiałek, Joanna; Dziadek, Michał

Providing safe food products to the consumer depends on the material and technology used and adherence to hygienic practices, throughout the production process. The degree of microbial contamination of a surface is an important indicator of equipment cleanliness and effectiveness of cleaning and disinfection. Used material, construction solutions and quality of the applied devices also have an effect on hygienic status. The objective of the present study was to evaluate the influence of the design and construction material of selected food storage racks, available on the Polish market, on their hygienic status. The study was based on determination of the capability of microbial growth on the surface of the racks and the effectiveness of their cleaning. Microbiological cleanliness on the surface of the racks was monitored by the contact plates which are able to estimate the total number of icroorganisms. Examination of effectiveness of cleaning was conducted by the use of ATP bioluminescence method. This experiment has proven a significant influence of adopted construction solutions on the hygienic status of the examined racks. Presence of antibacterial layer and a choice of the appropriate construction material characterized by a low surface roughness impedes the microbial growth and increases the effectiveness of cleaning. Design solutions have significant impact on the hygienic status of shelves. Selection of a suitable material for the construction of racks can greatly reduce the possibility of the development of microorganism, despite the low efficiency of the cleaning. The application of antimicrobial coatings inhibits microbial growth.

Anneli Randla kaitses doktorikraadi Cambridge'is / Anneli Randla ; interv. Reet Varblane

Index Scriptorium Estoniae

Randla, Anneli, 1970-

1999-01-01

5. mail kaitses Cambridge'is esimese eesti kunstiteadlasena doktorikraadi Anneli Randla. Töö teema: kerjusmungaordukloostrite arhitektuur Põhja-Euroopas. Juhendaja dr. Deborah Howard. Doktorikraadile esitatavatest nõudmistest, doktoritöö kaitsmisest, magistrikraadi kaitsnu õppimisvõimalustest Cambridge's.

Rack for nuclear fuel elements

International Nuclear Information System (INIS)

Rubinstein, H.J.; Gordon, C.B.; Robison, A.; Clark, P.M.

1977-01-01

Disclosed is a rack for storing spent nuclear fuel elements in which a plurality of aligned rows of upright enclosures of generally square cross-sectional areas contain vertically disposed spent fuel elements. Each fuel element is supported at the lower end thereof by a respective support that rests on the floor of the spent fuel pool for a nuclear power plant. An open rack frame is employed as an upright support for the enclosures containing the spent fuel elements. Legs at the lower corners of the frame rest on the floor of the pool to support the frame. In one exemplary embodiment, the support for the fuel element is in the form of a base on which a fuel element rests and the base is supported by legs. In another exemplary embodiment, each fuel element is supported on the pool floor by a self-adjusting support in the form of a base on which a fuel element rests and the base rests on a ball or swivel joint for self-alignment. The lower four corners of the frame are supported by legs adjustable in height for leveling the frame. Each adjustable frame leg is in the form of a base resting on the pool floor and the base supports a threaded post. The threaded post adjustably engages a threaded column on which rests the lower end of the frame. 16 claims, 14 figures

Three-dimensional microelectromechanical tilting platform operated by gear-driven racks

Science.gov (United States)

Klody, Kelly A.; Habbit, Jr., Robert D.

2005-11-01

A microelectromechanical (MEM) tiltable-platform apparatus is disclosed which utilizes a light-reflective platform (i.e. a micromirror) which is supported above a substrate by flexures which can be bent upwards to tilt the platform in any direction over an angle of generally .+-.10 degrees using a gear-driven rack attached to each flexure. Each rack is driven by a rotary microengine (i.e. a micromotor); and an optional thermal actuator can be used in combination with each microengine for initially an initial uplifting of the platform away from the substrate. The MEM apparatus has applications for optical switching (e.g. between a pair of optical fibers) or for optical beam scanning.

ISS Material Science Research Rack HWIL Interface Simulation

Science.gov (United States)

Williams, Philip J.; Ballard, Gary H.; Crumbley, Robert T. (Technical Monitor)

2002-01-01

In this paper, the first Material Science Research Rack (MSRR-1) hardware-in-the-loop (HWIL) interface simulation is described. Dynamic Concepts developed this HWIL simulation system with funding and management provided by the Flight Software group (ED14) of NASA-MSFC's Avionics Department. The HWIL system has been used both as a flight software development environment and as a software qualification tool. To fulfill these roles, the HWIL simulator accurately models the system dynamics of many MSRR-1 subsystems and emulates most of the internal interface signals. The modeled subsystems include the Experiment Modules, the Thermal Environment Control System, the Vacuum Access System, the Solid State Power Controller Module, and the Active Rack Isolation Systems. The emulated signals reside on three separate MIL-STD-1553B digital communication buses, the ISS Medium Rate Data Link, and several analog controller and sensor signals. To enhance the range of testing, it was necessary to simulate several off-nominal conditions that may occur in the interfacing subsystems.

Re-racking the spent fuel pit in nuclear power plant Krsko

International Nuclear Information System (INIS)

Volaric, B.; Krajnc, B.

2003-01-01

Krsko NPP was designed to temporary store a limited number of spent fuel assemblies (SFA). They were planned to be either removed for reprocessing or permanently stored. By the design the plant would run out of capacity for temporary storing of SFAs in 2003. This means that the plant could not operate further without additional changes since valid regulations require the Spent Fuel Pit (SFP) free storage capacity for the whole emergency core unloading (ECU). The purpose of the SFP Reracking Project is to assure a safe storage of all SFAs in the existing SFP during the plant lifetime. Design solutions and related analysis did not only consider the quantity of spent fuel for the plant lifetime, i.e. up to the year 2023, but also a possibility of the SFP extension for eventually extended plant lifetime of 20 years. According to the project, racks were designed to provide up to 1694 cells for storage of FAs in Phase I which is sufficient for normal NPP operation up to its lifetime, i.e. the year 2023. The extension of temporary storage capacity of SFAs in the SFP was made by a combination of existing and new high-density racks. Three modules from the existing 12 were eliminated. Thus leaving 621 cells. There are nine new racks added with up to 1073 supercompacted cells installed in the empty part of the pool. The spacing between new cells is smaller than the one between existing cells because of special plates, made of borated stainless steel. The design of the racks fulfils all the applicable requirements to ensure sub-criticality of all stored SFAs, enriched up to 5 % U 235 with peak pellet burnup above 40 GWD/MTU. Besides static and dynamic seismic loading of both, the racks and the fuel handling building, sufficient cooling of FAs is provided as well as accident conditions precluded. Greater cooling capacity is achieved by installing the third heat exchanger, connected in parallel to existing two exchangers. The design and manufacturing of the new heat exchanger

Ann tuleb Rakverest Võrru

Index Scriptorium Estoniae

2009-01-01

Võru kultuurimajas Kannel etendub 17. aprillil Rakvere teatri noortelavastus "Kuidas elad? ...Ann?!" Aidi Valliku jutustuse põhjal. Lavastaja Sven Heiberg. Mängivad ka Viljandi Kultuuriakadeemia teatritudengid

Source rack reload of the Tunisian gamma irradiation facility using Monte Carlo method

International Nuclear Information System (INIS)

Gharbi, Foued; Kadri, Omrane

2005-01-01

This work presents a Monte Carlo study of the cylindrical source rack geometry of the tunisian gamma irradiation facility, using Ge ant code of CERN. The study investigates the question of the reload of the source rack. studied configurations consist on housing four new pencils, two in the upper and two in the lower cylinder of the source rack. global dose rate uniformity inside a ''dummy's' product for the case of routine and non routine irradiation and as function of the product bulk density was calculated for eight hypothetical configurations. the same calculation was also performed for both of the original and the ideal, but not practical configuration. It was shown that hypothetical cases produced dose uniformity variations, according to product density, that were statistically no different than the original and the ideal configurations and that reload procedure can not improve the irradiation quality inside the tunisian facility

Influence of Rack Design and Disease Prevalence on Detection of Rodent Pathogens in Exhaust Debris Samples from Individually Ventilated Caging Systems.

Science.gov (United States)

Bauer, Beth A; Besch-Williford, Cynthia; Livingston, Robert S; Crim, Marcus J; Riley, Lela K; Myles, Matthew H

2016-11-01

Sampling of bedding debris within the exhaust systems of ventilated racks may be a mechanism for detecting murine pathogens in colony animals. This study examined the effectiveness of detecting pathogens by PCR analysis of exhaust debris samples collected from ventilated racks of 2 different rack designs, one with unfiltered air flow from within the cage to the air-exhaust pathway, and the other had a filter between the cage and the air-exhaust pathway. For 12 wk, racks were populated with either 1 or 5 cages of mice (3 mice per cage) infected with one of the following pathogens: mouse norovirus (MNV), mouse parvovirus (MPV), mouse hepatitis virus (MHV), Helicobacter spp., Pasteurella pneumotropica, pinworms, Entamoeba muris, Tritrichomonas muris, and fur mites. Pathogen shedding by infected mice was monitored throughout the study. In the filter-containing rack, PCR testing of exhaust plenums yielded negative results for all pathogens at all time points of the study. In the rack with open air flow, pathogens detected by PCR analysis of exhaust debris included MHV, Helicobacter spp., P. pneumotropica, pinworms, enteric protozoa, and fur mites; these pathogens were detected in racks housing either 1 or 5 cages of infected mice. Neither MPV nor MNV was detected in exhaust debris, even though prolonged viral shedding was confirmed. These results demonstrate that testing rack exhaust debris from racks with unfiltered air flow detected MHV, enteric bacteria and parasites, and fur mites. However, this method failed to reliably detect MNV or MPV infection of colony animals.

Anne Veski : "Ju siis ei ole minu rahvusvaheline kuulsus meie presidendi kõrvu jõudnud" / Anne Veski ; interv. Tiia Linnard

Index Scriptorium Estoniae

Veski, Anne, 1956-

2008-01-01

Laulja Anne Veski arutlusi kontserttegevusest Venemaal ja elust Eestis. Muuhulgas on juttu ka sellest, et Anne Veskit pole kunagi kutsutud presidendi iseseisvuspäeva vastuvõtule. Ilmunud ka: Severnoje Poberezhje 20. märts 2008, lk. 6

An Evaluation of Criticality Margin by an Application of Parallelogram Lattice Arrangement in the Nuclear Fuel Storage Rack

International Nuclear Information System (INIS)

Kim, Song Hyun; Kim, Hong Chul; Shin, Chang Ho; Kim, Jong Kyung; Kim, Kyo Youn

2010-01-01

The criticality evaluation in the nuclear fuel storage rack is essentially required for the prevention of the criticality accident. The square lattice structure of the storage rack is commonly used because it has a simple structure for the storage of the numerous fuel assemblies as well as the good mechanical strength. For the design of the fuel storage rack, the boron plate is commonly used for the criticality reduction. In this study, an arrangement method with the parallelogram lattice structure is proposed for the reduction of the boron concentration or the rack pitch. The criticality margins by the application of the parallelogram lattice were evaluated with MCNP5 code. From the result, the reduction of the boron concentrated in the borated-Al plate was evaluated

Review of the technical basis and verification of current analysis methods used to predict seismic response of spent fuel storage racks

International Nuclear Information System (INIS)

DeGrassi, G.

1992-10-01

This report presents the results of a literature review on spent fuel rack seismic analysis methods and modeling procedures. The analysis of the current generation of free standing high density spent fuel racks requires careful consideration of complex phenomena such as rigid body sliding and tilting motions; impacts between adjacent racks, between fuel assemblies and racks, and between racks and pool walls and floor; fluid coupling and frictional effects. The complexity of the potential seismic response of these systems raises questions regarding the levels of uncertainty and ranges of validity of the analytical results. BNL has undertaken a program to investigate and assess the strengths and weaknesses of current fuel rack seismic analysis methods. The first phase of this program involved a review of technical literature to identify the extent of experimental and analytical verification of the analysis methods and assumptions. Numerous papers describing analysis methods for free standing fuel racks were reviewed. However, the extent of experimental verification of these methods was found to be limited. Based on the information obtained from the literature review, the report provides an assessment of the significance of the issues of concern and makes recommendations for additional studies

Characterization of receptor of activated C kinase 1 (RACK1) and functional analysis during larval metamorphosis of the oyster Crassostrea angulata.

Science.gov (United States)

Yang, Bingye; Pu, Fei; Qin, Ji; You, Weiwei; Ke, Caihuan

2014-03-10

During a large-scale screen of the larval transcriptome library of the Portuguese oyster, Crassostrea angulata, the oyster gene RACK, which encodes a receptor of activated protein kinase C protein was isolated and characterized. The cDNA is 1,148 bp long and has a predicted open reading frame encoding 317 aa. The predicted protein shows high sequence identity to many RACK proteins of different organisms including molluscs, fish, amphibians and mammals, suggesting that it is conserved during evolution. The structural analysis of the Ca-RACK1 genomic sequence implies that the Ca-RACK1 gene has seven exons and six introns, extending approximately 6.5 kb in length. It is expressed ubiquitously in many oyster tissues as detected by RT-PCR analysis. The Ca-RACK1 mRNA expression pattern was markedly increased at larval metamorphosis; and was further increased along with Ca-RACK1 protein synthesis during epinephrine-induced metamorphosis. These results indicate that the Ca-RACK1 plays an important role in tissue differentiation and/or in cell growth during larval metamorphosis in the oyster, C. angulata. Copyright © 2013 Elsevier B.V. All rights reserved.

Recalculation with SEACAB of the activation by spent fuel neutrons and residual dose originated in the racks replaced at Cofrentes NPP

Directory of Open Access Journals (Sweden)

Ortego Pedro

2017-01-01

Full Text Available In order to increase the storage capacity of the East Spent Fuel Pool at the Cofrentes NPP, located in Valencia province, Spain, the existing storage stainless steel racks were replaced by a new design of compact borated stainless steel racks allowing a 65% increase in fuel storing capacity. Calculation of the activation of the used racks was successfully performed with the use of MCNP4B code. Additionally the dose rate at contact with a row of racks in standing position and behind a wall of shielding material has been calculated using MCNP4B code as well. These results allowed a preliminary definition of the burnker required for the storage of racks. Recently the activity in the racks has been recalculated with SEACAB system which combines the mesh tally of MCNP codes with the activation code ACAB, applying the rigorous two-step method (R2S developed at home, benchmarked with FNG irradiation experiments and usually applied in fusion calculations for ITER project.

Recalculation with SEACAB of the activation by spent fuel neutrons and residual dose originated in the racks replaced at Cofrentes NPP

Science.gov (United States)

Ortego, Pedro; Rodriguez, Alain; Töre, Candan; Compadre, José Luis de Diego; Quesada, Baltasar Rodriguez; Moreno, Raul Orive

2017-09-01

In order to increase the storage capacity of the East Spent Fuel Pool at the Cofrentes NPP, located in Valencia province, Spain, the existing storage stainless steel racks were replaced by a new design of compact borated stainless steel racks allowing a 65% increase in fuel storing capacity. Calculation of the activation of the used racks was successfully performed with the use of MCNP4B code. Additionally the dose rate at contact with a row of racks in standing position and behind a wall of shielding material has been calculated using MCNP4B code as well. These results allowed a preliminary definition of the burnker required for the storage of racks. Recently the activity in the racks has been recalculated with SEACAB system which combines the mesh tally of MCNP codes with the activation code ACAB, applying the rigorous two-step method (R2S) developed at home, benchmarked with FNG irradiation experiments and usually applied in fusion calculations for ITER project.

Mary Anne Chambers | IDRC - International Development Research ...

International Development Research Centre (IDRC) Digital Library (Canada)

A former Member of Provincial Parliament, Mary Anne served as Minister of Training, Colleges and Universities, and Minister of Children and Youth Services in the Government of Ontario. She is also a former senior vice-president of Scotiabank. A graduate of the University of Toronto, Mary Anne has received honorary ...

Experimental and Numerical Study of Bottom Rack Occlusion by Flow with Gravel-Sized Sediment. Application to Ephemeral Streams in Semi-Arid Regions

Directory of Open Access Journals (Sweden)

Luis G. Castillo

2016-04-01

Full Text Available Rainfall runoff collection in ephemeral streams is an objective in semi-arid zones. Rack intake systems are proposed to collect these flash floods with intensive sediment transport. The design parameters address the problem of clogging the spacing between bars. Experiments for two different void ratio racks are shown. Flows, longitudinal slopes in the rack, and water with three gravel-sized sediments were tested. Results such as effective void ratio due to the gravel deposition over the rack, the evolution of the flow rejected during each test, and the quantification of materials collected and deposited, are presented. The optimal longitudinal rack slope seems to be close to 30%. The effective void ratio is related to several hydraulic parameters calculated at the beginning of the rack. Some adjustments were proposed to predict the effective void ratio.

Retrieval-travel-time model for free-fall-flow-rack automated storage and retrieval system

Science.gov (United States)

Metahri, Dhiyaeddine; Hachemi, Khalid

2018-03-01

Automated storage and retrieval systems (AS/RSs) are material handling systems that are frequently used in manufacturing and distribution centers. The modelling of the retrieval-travel time of an AS/RS (expected product delivery time) is practically important, because it allows us to evaluate and improve the system throughput. The free-fall-flow-rack AS/RS has emerged as a new technology for drug distribution. This system is a new variation of flow-rack AS/RS that uses an operator or a single machine for storage operations, and uses a combination between the free-fall movement and a transport conveyor for retrieval operations. The main contribution of this paper is to develop an analytical model of the expected retrieval-travel time for the free-fall flow-rack under a dedicated storage assignment policy. The proposed model, which is based on a continuous approach, is compared for accuracy, via simulation, with discrete model. The obtained results show that the maximum deviation between the continuous model and the simulation is less than 5%, which shows the accuracy of our model to estimate the retrieval time. The analytical model is useful to optimise the dimensions of the rack, assess the system throughput, and evaluate different storage policies.

Retort Racks for Polymeric Trays in 1400 Style Spray Retorts

National Research Council Canada - National Science Library

Bruins, Henderikus B

2003-01-01

The objective of this project was to design a retort rack that would maximize the retort capacity of a 1400 style spray retort and to select a material that would withstand the harsh retort spray environment...

Nuclear import of transcription factor BR-C is mediated by its interaction with RACK1.

Science.gov (United States)

Cheng, Daojun; Qian, Wenliang; Wang, Yonghu; Meng, Meng; Wei, Ling; Li, Zhiqing; Kang, Lixia; Peng, Jian; Xia, Qingyou

2014-01-01

The transcription factor Broad Complex (BR-C) is an early ecdysone response gene in insects and contains two types of domains: two zinc finger domains for the activation of gene transcription and a Bric-a-brac/Tramtrack/Broad complex (BTB) domain for protein-protein interaction. Although the mechanism of zinc finger-mediated gene transcription is well studied, the partners interacting with the BTB domain of BR-C has not been elucidated until now. Here, we performed a yeast two-hybrid screen using the BTB domain of silkworm BR-C as bait and identified the receptor for activated C-kinase 1 (RACK1), a scaffolding/anchoring protein, as the novel partner capable of interacting with BR-C. The interaction between BR-C and RACK1 was further confirmed by far-western blotting and pull-down assays. Importantly, the disruption of this interaction, via RNAi against the endogenous RACK1 gene or deletion of the BTB domain, abolished the nuclear import of BR-C in BmN4 cells. In addition, RNAi against the endogenous PKC gene as well as phosphorylation-deficient mutation of the predicted PKC phosphorylation sites at either Ser373 or Thr406 in BR-C phenocopied RACK1 RNAi and altered the nuclear localization of BR-C. However, when BTB domain was deleted, phosphorylation mimics of either Ser373 or Thr406 had no effect on the nuclear import of BR-C. Moreover, mutating the PKC phosphorylation sites at Ser373 and Thr406 or deleting the BTB domain significantly decreased the transcriptional activation of a BR-C target gene. Given that RACK1 is necessary for recruiting PKC to close and phosphorylate target proteins, we suggest that the PKC-mediated phosphorylation and nuclear import of BR-C is determined by its interaction with RACK1. This novel finding will be helpful for further deciphering the mechanism underlying the role of BR-C proteins during insect development.

Nuclear import of transcription factor BR-C is mediated by its interaction with RACK1.

Directory of Open Access Journals (Sweden)

Daojun Cheng

Full Text Available The transcription factor Broad Complex (BR-C is an early ecdysone response gene in insects and contains two types of domains: two zinc finger domains for the activation of gene transcription and a Bric-a-brac/Tramtrack/Broad complex (BTB domain for protein-protein interaction. Although the mechanism of zinc finger-mediated gene transcription is well studied, the partners interacting with the BTB domain of BR-C has not been elucidated until now. Here, we performed a yeast two-hybrid screen using the BTB domain of silkworm BR-C as bait and identified the receptor for activated C-kinase 1 (RACK1, a scaffolding/anchoring protein, as the novel partner capable of interacting with BR-C. The interaction between BR-C and RACK1 was further confirmed by far-western blotting and pull-down assays. Importantly, the disruption of this interaction, via RNAi against the endogenous RACK1 gene or deletion of the BTB domain, abolished the nuclear import of BR-C in BmN4 cells. In addition, RNAi against the endogenous PKC gene as well as phosphorylation-deficient mutation of the predicted PKC phosphorylation sites at either Ser373 or Thr406 in BR-C phenocopied RACK1 RNAi and altered the nuclear localization of BR-C. However, when BTB domain was deleted, phosphorylation mimics of either Ser373 or Thr406 had no effect on the nuclear import of BR-C. Moreover, mutating the PKC phosphorylation sites at Ser373 and Thr406 or deleting the BTB domain significantly decreased the transcriptional activation of a BR-C target gene. Given that RACK1 is necessary for recruiting PKC to close and phosphorylate target proteins, we suggest that the PKC-mediated phosphorylation and nuclear import of BR-C is determined by its interaction with RACK1. This novel finding will be helpful for further deciphering the mechanism underlying the role of BR-C proteins during insect development.

An ANN application for water quality forecasting.

Science.gov (United States)

Palani, Sundarambal; Liong, Shie-Yui; Tkalich, Pavel

2008-09-01

Rapid urban and coastal developments often witness deterioration of regional seawater quality. As part of the management process, it is important to assess the baseline characteristics of the marine environment so that sustainable development can be pursued. In this study, artificial neural networks (ANNs) were used to predict and forecast quantitative characteristics of water bodies. The true power and advantage of this method lie in its ability to (1) represent both linear and non-linear relationships and (2) learn these relationships directly from the data being modeled. The study focuses on Singapore coastal waters. The ANN model is built for quick assessment and forecasting of selected water quality variables at any location in the domain of interest. Respective variables measured at other locations serve as the input parameters. The variables of interest are salinity, temperature, dissolved oxygen, and chlorophyll-alpha. A time lag up to 2Delta(t) appeared to suffice to yield good simulation results. To validate the performance of the trained ANN, it was applied to an unseen data set from a station in the region. The results show the ANN's great potential to simulate water quality variables. Simulation accuracy, measured in the Nash-Sutcliffe coefficient of efficiency (R(2)), ranged from 0.8 to 0.9 for the training and overfitting test data. Thus, a trained ANN model may potentially provide simulated values for desired locations at which measured data are unavailable yet required for water quality models.

First Materials Science Research Rack Capabilities and Design Features

Science.gov (United States)

Schaefer, D.; King, R.; Cobb, S.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

The first Materials Science Research Rack (MSRR-1) will accommodate dual Experiment Modules (EM's) and provide simultaneous on-orbit processing operations capability. The first international Materials Science Experiment Module for the MSRR-1 is an international cooperative research activity between NASA's Marshall Space Flight Center (MSFC) and the European Space Agency's (ESA) European Space Research and Technology Center. (ESTEC). This International Standard Payload Rack (ISPR) will contain the Materials Science Laboratory (MSL) developed by ESA as an Experiment Module. The MSL Experiment Module will accommodate several on-orbit exchangeable experiment-specific Module Inserts. Module Inserts currently planned are a Quench Module Insert, Low Gradient Furnace, Solidification with Quench Furnace, and Diffusion Module Insert. The second Experiment Module for the MSRR-1 configuration is a commercial device supplied by MSFC's Space Products Department (SPD). It includes capabilities for vapor transport processes and liquid metal sintering. This Experiment Module will be replaced on-orbit with other NASA Materials Science EMs.

OsRACK1 Is Involved in Abscisic Acid- and H2O2-Mediated Signaling to Regulate Seed Germination in Rice (Oryza sativa, L.)

Science.gov (United States)

Zhang, Dongping; Chen, Li; Li, Dahong; Lv, Bing; Chen, Yun; Chen, Jingui; XuejiaoYan; Liang, Jiansheng

2014-01-01

The receptor for activated C kinase 1 (RACK1) is one member of the most important WD repeat–containing family of proteins found in all eukaryotes and is involved in multiple signaling pathways. However, compared with the progress in the area of mammalian RACK1, our understanding of the functions and molecular mechanisms of RACK1 in the regulation of plant growth and development is still in its infancy. In the present study, we investigated the roles of rice RACK1A gene (OsRACK1A) in controlling seed germination and its molecular mechanisms by generating a series of transgenic rice lines, of which OsRACK1A was either over-expressed or under-expressed. Our results showed that OsRACK1A positively regulated seed germination and negatively regulated the responses of seed germination to both exogenous ABA and H2O2. Inhibition of ABA biosynthesis had no enhancing effect on germination, whereas inhibition of ABA catabolism significantly suppressed germination. ABA inhibition on seed germination was almost fully recovered by exogenous H2O2 treatment. Quantitative analyses showed that endogenous ABA levels were significantly higher and H2O2 levels significantly lower in OsRACK1A-down regulated transgenic lines as compared with those in wildtype or OsRACK1A-up regulated lines. Quantitative real-time PCR analyses showed that the transcript levels of OsRbohs and amylase genes, RAmy1A and RAmy3D, were significantly lower in OsRACK1A-down regulated transgenic lines. It is concluded that OsRACK1A positively regulates seed germination by controlling endogenous levels of ABA and H2O2 and their interaction. PMID:24865690

Final Technical Report, Wind Generator Project (Ann Arbor)

Energy Technology Data Exchange (ETDEWEB)

Geisler, Nathan [City of Ann Arbor, MI (United States)

2017-03-20

A Final Technical Report (57 pages) describing educational exhibits and devices focused on wind energy, and related outreach activities and programs. Project partnership includes the City of Ann Arbor, MI and the Ann Arbor Hands-on Museum, along with additional sub-recipients, and U.S. Department of Energy/Office of Energy Efficiency and Renewable Energy (EERE). Report relays key milestones and sub-tasks as well as numerous graphics and images of five (5) transportable wind energy demonstration devices and five (5) wind energy exhibits designed and constructed between 2014 and 2016 for transport and use by the Ann Arbor Hands-on Museum.

77 FR 27029 - Certain Kitchen Shelving and Racks From the People's Republic of China: Extension of Time Limit...

Science.gov (United States)

2012-05-08

... DEPARTMENT OF COMMERCE International Trade Administration [C-570-942] Certain Kitchen Shelving and Racks From the People's Republic of China: Extension of Time Limit for Preliminary Results of... certain kitchen appliance shelving and racks from the People's Republic of China, covering the review...

Rollin' in Style!: Students Design Bike Mounted Skateboard Racks

Science.gov (United States)

Massey, Rick

2008-01-01

Recognizing the increasing popularity of skateboarding, the author has found a project that teaches design and manufacturing concepts--and, of equal importance, really gets his students motivated. He challenges them to design and build a skateboard rack that mounts easily on a bicycle. The project benefits students by teaching creativity, the…

Thermal analyses for the rack design with spent fuel pool during the loss of cooling accident

Energy Technology Data Exchange (ETDEWEB)

Yeh, C-L.; Chen, Y-S.; Chen, B-Y., E-mail: clinyeh@iner.gov.tw, E-mail: yschen@iner.gov.tw, E-mail: onepicemine@iner.gov.tw [Inst. of Nuclear Energy Research, Taoyuan County, Taiwan (China); Tseng, Y-S., E-mail: ystseng@mx.nthu.edu.tw [National Tsing Hua Univ., Engineering and System Science, Hsinchu, Taiwan (China); Wei, W-C., E-mail: hn150456@iner.gov.tw [Inst. of Nuclear Energy Research, Taoyuan County, Taiwan (China)

2014-07-01

Alternative fuel arrangements separating the latest fuels discharge from the reactor core are proposed, such as the 1x4 configuration in which the hot assembly is surrounded by 4 assemblies with much lower decay heat. For the rack design in the BWR spent fuel pool design, the lateral flow is eliminated by solid walls. In this study, cooling enhancement of splitting fuel rack is investigated using Computational Fluid Dynamics (CFD). The fuels in the pool are modeled by porous medium. Separating the fuel rack by a distance of 10 cm can lower the peak cladding temperature and the natural convection between the fuels and then earns more response time for the site people to implement necessary mitigation actions. (author)

Lessons Learned "Establishing an Electrically Safe Work Condition" Specifically related to Racking Electrical Breakers

Energy Technology Data Exchange (ETDEWEB)

Martinez, Tommy Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Romero, Philbert Roland [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Garcia, Samuel Anthony [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-11-09

During low voltage electrical equipment maintenance, a bad breaker was identified. The breaker was racked out from the substation cubicle without following the hazardous energy control process identified in the Integrated Work Document (IWD). The IWD required the substation to be in an electrically safe work condition prior to racking the breaker. Per NFPA 70E requirements, electrical equipment shall be put into an electrically safe work condition before an employee performs work on or interacts with equipment in a manner that increases the likelihood of creating an arc flash. Racking in or out a breaker on an energized bus may increase the likelihood of creating an arc flash dependent on equipment conditions. A thorough risk assessment must be performed prior to performing such a task. The risk assessment determines the risk control measures to be put in place prior to performing the work. Electrical Safety Officers (ESO) can assist in performing risk assessments and incorporating risk control measures.

40 CFR Table 9 to Subpart Eeee of... - Continuous Compliance With Operating Limits-High Throughput Transfer Racks

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Continuous Compliance With Operating Limits-High Throughput Transfer Racks 9 Table 9 to Subpart EEEE of Part 63 Protection of Environment...—Continuous Compliance With Operating Limits—High Throughput Transfer Racks As stated in §§ 63.2378(a) and (b...

FSI-based Overflow Assessment of the Seismically-Isolated SFP with Fuel Racks

Energy Technology Data Exchange (ETDEWEB)

Chung, Gil Y.; Park, Hyun T.; Chang, Soo-Hyuk [Korea Maintenance Co., Seoul (Korea, Republic of); Lee, Sang-Hoon [KEPCO E-C, Yongin (Korea, Republic of)

2014-10-15

To date, effectiveness of the seismic isolation systems for reducing seismic force effectively has been well demonstrated. In this context, practical application of the technology in nuclear engineering fields has become an important issue more and more. This is because fluid motion can be rather amplified due to the increased relative displacement between the base and superstructures by a long-period shift. Therefore, overflow assessment and prediction of the seismically-isolated SFP have to be conducted in design phase. For performing sloshing-induced overflow of the seismically-isolated SFP, a fluid-structure interaction(FSI) approach making a two-way coupling process between structural and fluid solvers is herein employed. In this study, fuel racks inside the SFP are included in FSI modeling to investigate effect of fuel-cell assemblies on SFP overflow. Accordingly, three different assembly sets of fuel cells are assumed to be inserted in fuel racks. In addition, floor acceleration time-histories produced from three different amplitudes of peak ground acceleration (PGA) are applied to the SFP base to investigate load effect on liquid overflow. An approach for the liquid overflow assessment of the seismically-isolated nuclear SFP with fuel storage racks based on FSI analysis was addressed. From the results of the identified cases, the following conclusions are drawn: (i) FSI technique can be effectively used to assess the seismically-isolated SFP overflow, (ii) In a conservative way, the isolated SFP without fuel racks can be used to assess its sloshing-induced overflow under earthquake since effect of fuel-cell assemblies on the SFP overflow is not significant, (iii) for given same conditions (e.g., constant design free surface, same fuel-cell assembly) except seismic loading, the higher PGA is, the more liquid overflow increases.

Anne Frank relaunched in the world of comics and graphic novels

NARCIS (Netherlands)

Ribbens, Kees

2017-01-01

Recently the Basel-based Anne Frank Fonds proudly presented the Graphic Diary of Anne Frank. The impression is created as if this is the first ever comic book version of Anne Frank’s narrative. This article shows that there were various predecessors.

To the question about the layout of the racks in the warehouse

Directory of Open Access Journals (Sweden)

Ilesaliev D.I.

2017-03-01

Full Text Available Warehouses, which are located at points of transshipment of cargo from one type of transport on the other, play a sig-nificant role in the transformation of cargo to further the most effective transportation of goods. The location of racks and longitudinal passages are important in the work of transhipment warehouse. Typically, racks and longitudinal pas-sages are perpendicular to each other, the article proposes a radical change with the "euclidean advantage". This is an-other way of designing warehouses for efficiency overload packaged cargo in the supply chain. Purpose is to reduce the mileage for one cycle of the loader from loading and unloading areas to storage areas.

Storage racks for spent nuclear fuels

International Nuclear Information System (INIS)

Matsumoto, Takashi; Ukaji, Hideo; Okino, Yoshiyuki; Ishihara, Jo; Ikuta, Isao.

1983-01-01

Purpose: To facilitate the mounting of neutron absorbers made of amorphous alloys to fuel racks. Constitution: Neutron absorbers are mounted to a cylindrical member of a square cross section for containing to retain spent fuels only on paired opposing sides by means of machine screws or the likes. Then, such cylindrical members are disposed so that their sides attached with the neutron absorbers are not in adjacent with each other. In this way, mounting of the neutron absorbers over the entire surface of the cylindrical members is no more necessary thereby enabling to simplify the mounting work. (Ikeda, J.)

RACK1 forms a complex with FGFR1 and PKM2, and stimulates the growth and migration of squamous lung cancer cells.

Science.gov (United States)

Zhou, Chengzhi; Chen, Tao; Xie, Zhanhong; Qin, Yinyin; Ou, Yangming; Zhang, Jiexia; Li, Shiyue; Chen, Rongchang; Zhong, Nanshan

2017-11-01

Phosphorylation of Pyruvate Kinase M2 (PKM2) on Tyr105 by fibroblast growth factor receptor 1 (FGFR1) has been shown to promote its nuclear localization as well as cell growth in lung cancer. Better understanding the regulation of this process would benefit the clinical treatment for lung cancer. Here, it has been found that the adaptor protein receptor for activated PKC kinase (RACK1) formed a complex with FGFR1 and PKM2, and activated the FGFR1/PKM2 signaling. Knocking down the expression of RACK1 impaired the phosphorylation on Tyr105 of PKM2 and inhibited the growth and migration of lung cancer cells, while over-expression of RACK1 in lung cancer cells led to the resistance to Erdafitinib. Moreover, knocking down the expression of RACK1 impaired the tumorigenesis of lung cancer driven by LKB loss and mutated Ras (KrasG12D). Taken together, our study demonstrated the pivotal roles of RACK1 in FGFR1/PKM2 signaling, suggesting FGFR1/RACK1/PKM2 might be a therapeutic target for lung cancer treatment. © 2017 Wiley Periodicals, Inc.

Stability Analysis Of 3-d Conventional Pallet Rack Structures With Semi-rigid Connections

Directory of Open Access Journals (Sweden)

Kamal M. Bajoria

2009-12-01

Full Text Available This paper describe the three dimensional finite element modeling and buckling analysis of conventional pallet racking system with semi rigid connection. In this study three dimensional models of conventional pallet racking system were prepared using the finiteelement program ANSYS and finite element analysis carried out on conventional pallet racks with the 18 types of column sections developed along with semi-rigid connections. A parametric study was carried out to compare the effective length approach and the finiteelement method for accuracy and appropriateness for cold-formed steel frame design. Numerous frame elastic buckling analyses were carried out to evaluate the alignment chart and the AISI torsional-flexural buckling provisions. The parameters that influence the valueof Kx for column flexural buckling were examined in this study. The alignment chart and the AISI torsional-flexural buckling provisions, used to obtain the effective lengths and elastic buckling load of members were also evaluated. Results showed that the elastic buckling load obtained from the AISI torsional-flexural buckling provisions is generally conservative compared to the results obtained from performing frame elastic buckling analysis. Results also showed that, the effective length approach is more conservative than the finite element approach.

Shaping of Rack Cutter Original Profile for Fine-module Ratchet Teeth Cutting

Science.gov (United States)

Sharkov, O. V.; Koryagin, S. I.; Velikanov, N. L.

2018-05-01

The design models and the process of shaping the cutting edges of the rack cutter for cutting fine-module ratchet teeth are considered in the article. The use of fine-module ratchet teeth can reduce the noise and impact loads during operation of the freewheel mechanisms. Mathematical dependencies for calculating the coordinates determining the geometric position of the points of the front and back edges of the cutting profile of the rack cutter, the workpiece angle of rotation during cutting the ratchet teeth were obtained. When applying the developed method, the initial data are: the radii of the workpiece circumferences passing through the dedendum of the external and internal cut teeth; gradient angles of the front and back edges of the rail.

Habitat use by Red Knots (Calidris canutus rufa): Experiments with oyster racks and reefs on the beach and intertidal of Delaware Bay, New Jersey

Science.gov (United States)

Burger, Joanna; Niles, Lawrence J.

2017-07-01

Sea level rise and increasing human activities have decreased intertidal habitat in many places in the world. The expansion of aquaculture in intertidal areas may impact birds and other organisms using these habitats, leading to questions of sustainability of both aquaculture and functioning estuarine ecosystems. Understanding the effect of oyster culture on shorebird activity, particularly on Red Knots (Calidris canutus rufa), a species on the U.S. Threatened List, is important for adaptive management and the expansion of oyster culture. In May 2013 we experimentally compared Red Knot and shorebird use of a beach section with racks and a control, and in 2016 we compared the use of sections with artificial reefs, oyster racks, and control on Delaware Bay, New Jersey (USA). The data included only times when no workers or other people were present. Censuses, conducted every 30 min throughout the day (279 censuses in 2013, 231 censuses in 2016), included the number of Red Knots and other shorebirds in each treatment section. In 2013, the total number of shorebirds was significantly higher in the rack section than in the control section, except for Red Knots and Ruddy Turnstones (Arenaria interpres) that occurred in higher numbers in the control than in the rack section. In 2016 Red Knot numbers were also significantly lower in the rack section. In 2013, the mean number of Red Knots/census was 13 for racks vs 59 for the control (P racks and over 68 for other treatments (P racks while both foraging and roosting, suggesting that caution should be used before placing oyster racks in areas used for foraging by Red Knots.

RACK1 downregulates levels of the pro-apoptotic protein Fem1b in apoptosis-resistant colon cancer cells.

Science.gov (United States)

Subauste, M Cecilia; Ventura-Holman, Tereza; Du, Liqin; Subauste, Jose S; Chan, Shing-Leng; Yu, Victor C; Maher, Joseph F

2009-12-01

Evasion of apoptosis plays an important role in colon cancer progression. Following loss of the Apc tumor suppressor gene in mice, the gene encoding Fem1b is upregulated early in neoplastic intestinal epithelium. Fem1b is a pro-apoptotic protein that interacts with Fas, TNFR1 and Apaf-1, and increased expression of Fem1b induces apoptosis of cancer cells. Fem1b is a homolog of FEM-1, a protein in Caenorhabditis elegans that is negatively regulated by ubiquitination and proteasomal degradation. To study Fem1b regulation in colon cancer progression, we used apoptotis-sensitive SW480 cells, derived from a primary colon cancer, and their isogenic, apoptosis-resistant counterparts SW620 cells, derived from a subsequent metastatic lesion in the same patient. Treatment with proteasome inhibitor increased Fem1b protein levels in SW620 cells, but not in SW480 cells. In SW620 cells we found that endogenous Fem1b co-immunoprecipitates in complexes with RACK1, a protein known to mediate ubiquitination and proteasomal degradation of other pro-apoptotic proteins and to be upregulated in colon cancer. Full-length Fem1b, or the N-terminal region of Fem1b, associated with RACK1 when co-expressed in HEK293T cells, and RACK1 stimulated ubiquitination of Fem1b. RACK1 overexpression in SW620 cells led to downregulation of Fem1b protein levels. Conversely, downregulation of RACK1 led to upregulation of Fem1b protein levels, associated with induction of apoptosis, and this apoptosis was inhibited by blocking Fem1b protein upregulation. In conclusion, RACK1 downregulates levels of the pro-apoptotic protein Fem1b in metastatic, apoptosis-resistant colon cancer cells, which may promote apoptosis-resistance during progression of colon cancer.

Can an off-the-rack orthotic stiletto alter pressure and comfort scores in the forefoot, arch and heel?

DEFF Research Database (Denmark)

Penny, Jeannette Østergaard; Speedtsberg, Merete Brink; Kallemose, Thomas

2018-01-01

MTH2+3 pressure (p rack orthotic stilettos can notably reduce...... plantar pressures and improve forefoot and heel comfort during everyday use. Practitioner Summary: Off-the-rack orthotic stilettos with built-in metatarsal pad, arch support and heel caps can lower the pressure under the heel and forefoot in comparison with a standard stiletto and can improve comfort...

Preparation and planning for the replacement of the Oregon State University TRIGA reactor rotary specimen rack assembly

International Nuclear Information System (INIS)

Anderson, T.V.; Dodd, B.; Johnson, A.G.; Carpenter, W.T.

1984-01-01

Recently there have been a number of indications that the rotating rack may be approaching the end of its useful life. In order to benefit from the experience of other reactors who have removed and replaced their rotating racks, General Atomic (GA) was contacted and previous TRIGA Conference proceedings were scanned. It was determined that a number of facilities, had experienced difficulties with their lazy susans and eventually had to replace them. However, most of the written descriptions of this project were not sufficiently detailed to be of great use. The purpose of this paper is to identify some of the more important questions related to the replacement of our rotating rack assembly and OSU's currently proposed solutions, with a view towards soliciting ideas from other members of the TRIGA reactor community

[Anne Arold. Kontrastive Analyse...] / Paul Alvre

Index Scriptorium Estoniae

Alvre, Paul, 1921-2008

2001-01-01

Arvustus: Arold, Anne. Kontrastive analyse der Wortbildungsmuster im Deutschen und im Estnischen (am Beispiel der Aussehensadjektive). Tartu, 2000. (Dissertationes philologiae germanicae Universitatis Tartuensis)

Lessons Learned from the Crew Health Care System (CHeCS) Rack 1 Environmental Control and Life Support (ECLS) Design

Science.gov (United States)

Williams, David E.

2006-01-01

This paper will provide an overview of the International Space Station (ISS) Environmental Control and Life Support (ECLS) design of the Crew Health Care System (CHeCS) Rack 1 and it will document some of the lessons that have been learned to date for the ECLS equipment in this rack.

Performance evaluation of METAMIC neutron absorber in spent fuel storage rack

Directory of Open Access Journals (Sweden)

Kiyoung Kim

2018-06-01

Full Text Available High-density spent fuel (SF storage racks have been installed to increase SF pool capacity. In these SF racks, neutron absorber materials were placed between fuel assemblies allowing the storage of fuel assemblies in close proximity to one another. The purpose of the neutron absorber materials is to preclude neutronic coupling between adjacent fuel assemblies and to maintain the fuel in a subcritical storage condition. METAMIC neutron absorber has been used in high-density storage racks. But, neutron absorber materials can be subject to severe conditions including long-term exposure to gamma radiation and neutron radiation. Recently, some of them have experienced degradation, such as white spots on the surface. Under these conditions, the material must continue to serve its intended function of absorbing neutrons. For the first time in Korea, this article uses a neutron attenuation test to examine the performance of METAMIC surveillance coupons. Also, scanning electron microscope analysis was carried out to verify the white spots that were detected on the surface of METAMIC. In the neutron attenuation test, there was no significant sign of boron loss in most of the METAMIC coupons, but the coupon with white spots had relatively less B-10 content than the others. In the scanning electron microscope analysis, corrosion material was detected in all METAMIC coupons. Especially, it was confirmed that the coupon with white spots contains much more corrosion material than the others. Keywords: Blister, Criticality, METAMIC, Neutron Absorber, Neutron Attenuation Test, Scanning Electron Microscope

HOTLink rack monitor

International Nuclear Information System (INIS)

Al R Franck et al.

2001-01-01

A remote data acquisition chassis, called a HOTLink Rack Monitor, HRM, has been developed for use in the Fermilab control system. This chassis provides for 64 analog input channels, 8 analog output channels, and 8 bytes of digital I/O. The interface to the host VMEbus crate is by way of a 320 MHz HOTLink serial connection to a PMC mezzanine module. With no processor intervention, all data sources in the remote chassis are read at 100 sec intervals, time stamped, and stored in a 2 MB circular buffer on the PMC module. In operation, the memory always contains the most recent 16 k samples of 10 kHz data from all 64 analog input channels. An expansion module that resides in the HRM chassis records snapshot data for 8 analog channels, each channel consisting of up to 16 k readings, digitized at rates up to 10 MHz. Snapshot data is also returned and stored in buffers on the PMC module. Because the HRM presents a memory-mapped interface to the host, it is independent of the operating system and may be used in any system that supports PMC mezzanine modules

Optimising training data for ANNs with Genetic Algorithms

OpenAIRE

Kamp , R. G.; Savenije , H. H. G.

2006-01-01

International audience; Artificial Neural Networks (ANNs) have proved to be good modelling tools in hydrology for rainfall-runoff modelling and hydraulic flow modelling. Representative datasets are necessary for the training phase in which the ANN learns the model's input-output relations. Good and representative training data is not always available. In this publication Genetic Algorithms (GA) are used to optimise training datasets. The approach is tested with an existing hydraulic model in ...

Optimising training data for ANNs with Genetic Algorithms

OpenAIRE

R. G. Kamp; R. G. Kamp; H. H. G. Savenije

2006-01-01

Artificial Neural Networks (ANNs) have proved to be good modelling tools in hydrology for rainfall-runoff modelling and hydraulic flow modelling. Representative datasets are necessary for the training phase in which the ANN learns the model's input-output relations. Good and representative training data is not always available. In this publication Genetic Algorithms (GA) are used to optimise training datasets. The approach is tested with an existing hydraulic model in The Netherlands. An...

Method and apparatus for storing nuclear fuel assemblies in maximum density racks

International Nuclear Information System (INIS)

Wachter, W.J.; Robbins, T.R.

1979-01-01

A maximum density storage rack is provided for long term or semipermanent storage of spent nuclear fuel assemblies. The rack consists of storage cells arranged in a regular array, such as a checkerboard, and intended to be immersed in water. Initially, cap members are placed on alternate cells in such a manner that at least 50% of the cells are left open, some of the caps being removable. Spent fuel assemblies are then placed in the open cells until all of them are filled. The level of reactivity of each of the stored fuel assemblies is then determined by accurate calculation or by measurement, and the removable caps are removed and rearranged so that other cells are opened, permitting the storage of additional fuel assemblies in a pattern based on the actual reactivity such that criticality is prevented

Experimental study on hydraulic characteristic around trash rack of a pumping station

Science.gov (United States)

Zhou, MinZhe; Li, TongChun; Lin, XiangYang; Liu, XiaoQing; Ding, Yuan; Liu, GuangYuan

2017-11-01

This paper focuses on flow pattern around trash rack of intake of a pumping station project. This pumping station undertake the task of supplying up to 3,500,000 m3 water per day for a megacity. Considering the large flow rate, high lift, multi-pipe supply and long-time operation in this water conveyance pumping station, we built a physical model test to measure the flow velocity and observe the flow pattern to verify the reasonability of preliminary design. In this test, we set 3 layers of current meters around each trash rack of intake in reservoir to collect the flow velocity. Furthermore, we design 2 operating conditions of 9 pumps to observe the change of flow pattern. Finally, we found the velocity data were in a normal range under 2 different operating conditions of the 9 pump units.

Storage rack for nuclear fuel assemblies

International Nuclear Information System (INIS)

Wachter, W.J.

1988-01-01

A storage rack for nuclear fuel assemblies is described comprising storage tubes, each having a polygon cross-section. The tubes being nested with cell walls of one tube aligned with and confronting cell walls of other tubes. Each cell wall having an array of embossed buttons so arranged that buttons of one cell wall engage buttons of a confronting cell wall, and the engage buttons are welded together to secure the tubes. At least one layer of neutron-poison material comprises a flexible, resilient pad interprosed between the aligned cell walls; whereby a major portion of the total outer surface area of each confronting cell wall is engaged with the layer of neutron-poison material

Assessment of ANN and SVM models for estimating normal direct irradiation (H_b)

International Nuclear Information System (INIS)

Santos, Cícero Manoel dos; Escobedo, João Francisco; Teramoto, Érico Tadao; Modenese Gorla da Silva, Silvia Helena

2016-01-01

Highlights: • The performance of SVM and ANN in estimating Normal Direct Irradiation (H_b) was evaluated. • 12 models using different input variables are developed (hourly and daily partitions). • The most relevant input variables for DNI are kt, H_s_c and insolation ratio (r′ = n/N). • Support Vector Machine (SVM) provides accurate estimates and outperforms the Artificial Neural Network (ANN). - Abstract: This study evaluates the estimation of hourly and daily normal direct irradiation (H_b) using machine learning techniques (ML): Artificial Neural Network (ANN) and Support Vector Machine (SVM). Time series of different meteorological variables measured over thirteen years in Botucatu were used for training and validating ANN and SVM. Seven different sets of input variables were tested and evaluated, which were chosen based on statistical models reported in the literature. Relative Mean Bias Error (rMBE), Relative Root Mean Square Error (rRMSE), determination coefficient (R"2) and “d” Willmott index were used to evaluate ANN and SVM models. When compared to statistical models which use the same set of input variables (R"2 between 0.22 and 0.78), ANN and SVM show higher values of R"2 (hourly models between 0.52 and 0.88; daily models between 0.42 and 0.91). Considering the input variables, atmospheric transmissivity of global radiation (kt), integrated solar constant (H_s_c) and insolation ratio (n/N, n is sunshine duration and N is photoperiod) were the most relevant in ANN and SVM models. The rMBE and rRMSE values in the two time partitions of SVM models are lower than those obtained with ANN. Hourly ANN and SVM models have higher rRMSE values than daily models. Optimal performance with hourly models was obtained with ANN4"h (rMBE = 12.24%, rRMSE = 23.99% and “d” = 0.96) and SVM4"h (rMBE = 1.75%, rRMSE = 20.10% and “d” = 0.96). Optimal performance with daily models was obtained with ANN2"d (rMBE = −3.09%, rRMSE = 18.95% and “d” = 0

Design, Fabrication, and Testing of a Composite Rack Prototype in Support of the Deep Space Habitat Program

Science.gov (United States)

Smith, Russ; Hagen, Richard

2015-01-01

In support of the Deep Space Habitat project a number of composite rack prototypes were developed, designed, fabricated and tested to various extents ( with the International Standard Payload Rack configuration, or crew quarters, as a baseline). This paper focuses specifically on a composite rack prototype with a direct tie in to Space Station hardware. The outlined prototype is an all composite construction, excluding metallic fasteners, washers, and their associated inserts. The rack utilizes braided carbon composite tubing for the frame with the sidewalls, backwall and flooring sections utilizing aircraft grade composite honeycomb sandwich panels. Novel additively manufactured thermoplastic joints and tube inserts were also developed in support of this effort. Joint and tube insert screening tests were conducted at a preliminary level. The screening tests allowed for modification, and enhancement, of the fabrication and design approaches, which will be outlined. The initial joint tests did not include mechanical fasteners. Adhesives were utilized at the joint to composite tube interfaces, along with mechanical fasteners during final fabrication (thus creating a stronger joint than the adhesive only variant). In general the prototype was focused on a potential in-space assembly approach, or kit-of-parts construction concept, which would not necessarily require the inclusion of an adhesive in the joint regions. However, given the tie in to legacy Station hardware (and potential flight loads with imbedded hardware mass loadings), the rack was built as stiff and strong as possible. Preliminary torque down tests were also conducted to determine the feasibility of mounting the composite honeycomb panels to the composite tubing sections via the additively manufactured tube inserts. Additional fastener torque down tests were also conducted with inserts (helicoils) imbedded within the joints. Lessons learned are also included and discussed.

RegnANN: Reverse Engineering Gene Networks using Artificial Neural Networks.

Directory of Open Access Journals (Sweden)

Marco Grimaldi

Full Text Available RegnANN is a novel method for reverse engineering gene networks based on an ensemble of multilayer perceptrons. The algorithm builds a regressor for each gene in the network, estimating its neighborhood independently. The overall network is obtained by joining all the neighborhoods. RegnANN makes no assumptions about the nature of the relationships between the variables, potentially capturing high-order and non linear dependencies between expression patterns. The evaluation focuses on synthetic data mimicking plausible submodules of larger networks and on biological data consisting of submodules of Escherichia coli. We consider Barabasi and Erdös-Rényi topologies together with two methods for data generation. We verify the effect of factors such as network size and amount of data to the accuracy of the inference algorithm. The accuracy scores obtained with RegnANN is methodically compared with the performance of three reference algorithms: ARACNE, CLR and KELLER. Our evaluation indicates that RegnANN compares favorably with the inference methods tested. The robustness of RegnANN, its ability to discover second order correlations and the agreement between results obtained with this new methods on both synthetic and biological data are promising and they stimulate its application to a wider range of problems.

Playing tag with ANN: boosted top identification with pattern recognition

International Nuclear Information System (INIS)

Almeida, Leandro G.; Backović, Mihailo; Cliche, Mathieu; Lee, Seung J.; Perelstein, Maxim

2015-01-01

Many searches for physics beyond the Standard Model at the Large Hadron Collider (LHC) rely on top tagging algorithms, which discriminate between boosted hadronic top quarks and the much more common jets initiated by light quarks and gluons. We note that the hadronic calorimeter (HCAL) effectively takes a “digital image" of each jet, with pixel intensities given by energy deposits in individual HCAL cells. Viewed in this way, top tagging becomes a canonical pattern recognition problem. With this motivation, we present a novel top tagging algorithm based on an Artificial Neural Network (ANN), one of the most popular approaches to pattern recognition. The ANN is trained on a large sample of boosted tops and light quark/gluon jets, and is then applied to independent test samples. The ANN tagger demonstrated excellent performance in a Monte Carlo study: for example, for jets with p T in the 1100–1200 GeV range, 60% top-tag efficiency can be achieved with a 4% mis-tag rate. We discuss the physical features of the jets identified by the ANN tagger as the most important for classification, as well as correlations between the ANN tagger and some of the familiar top-tagging observables and algorithms.

Playing tag with ANN: boosted top identification with pattern recognition

Energy Technology Data Exchange (ETDEWEB)

Almeida, Leandro G. [Institut de Biologie de l’École Normale Supérieure (IBENS), Inserm 1024- CNRS 8197,46 rue d’Ulm, 75005 Paris (France); Backović, Mihailo [Center for Cosmology, Particle Physics and Phenomenology - CP3,Universite Catholique de Louvain,Louvain-la-neuve (Belgium); Cliche, Mathieu [Laboratory for Elementary Particle Physics, Cornell University,Ithaca, NY 14853 (United States); Lee, Seung J. [Department of Physics, Korea Advanced Institute of Science and Technology,335 Gwahak-ro, Yuseong-gu, Daejeon 305-701 (Korea, Republic of); School of Physics, Korea Institute for Advanced Study,Seoul 130-722 (Korea, Republic of); Perelstein, Maxim [Laboratory for Elementary Particle Physics, Cornell University,Ithaca, NY 14853 (United States)

2015-07-17

Many searches for physics beyond the Standard Model at the Large Hadron Collider (LHC) rely on top tagging algorithms, which discriminate between boosted hadronic top quarks and the much more common jets initiated by light quarks and gluons. We note that the hadronic calorimeter (HCAL) effectively takes a “digital image' of each jet, with pixel intensities given by energy deposits in individual HCAL cells. Viewed in this way, top tagging becomes a canonical pattern recognition problem. With this motivation, we present a novel top tagging algorithm based on an Artificial Neural Network (ANN), one of the most popular approaches to pattern recognition. The ANN is trained on a large sample of boosted tops and light quark/gluon jets, and is then applied to independent test samples. The ANN tagger demonstrated excellent performance in a Monte Carlo study: for example, for jets with p{sub T} in the 1100–1200 GeV range, 60% top-tag efficiency can be achieved with a 4% mis-tag rate. We discuss the physical features of the jets identified by the ANN tagger as the most important for classification, as well as correlations between the ANN tagger and some of the familiar top-tagging observables and algorithms.

40 CFR 63.11088 - What requirements must I meet for gasoline loading racks if my facility is a bulk gasoline...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 14 2010-07-01 2010-07-01 false What requirements must I meet for gasoline loading racks if my facility is a bulk gasoline terminal, pipeline breakout station, or pipeline... § 63.11088 What requirements must I meet for gasoline loading racks if my facility is a bulk gasoline...

Hybrid LSA-ANN Based Home Energy Management Scheduling Controller for Residential Demand Response Strategy

Directory of Open Access Journals (Sweden)

Maytham S. Ahmed

2016-09-01

Full Text Available Demand response (DR program can shift peak time load to off-peak time, thereby reducing greenhouse gas emissions and allowing energy conservation. In this study, the home energy management scheduling controller of the residential DR strategy is proposed using the hybrid lightning search algorithm (LSA-based artificial neural network (ANN to predict the optimal ON/OFF status for home appliances. Consequently, the scheduled operation of several appliances is improved in terms of cost savings. In the proposed approach, a set of the most common residential appliances are modeled, and their activation is controlled by the hybrid LSA-ANN based home energy management scheduling controller. Four appliances, namely, air conditioner, water heater, refrigerator, and washing machine (WM, are developed by Matlab/Simulink according to customer preferences and priority of appliances. The ANN controller has to be tuned properly using suitable learning rate value and number of nodes in the hidden layers to schedule the appliances optimally. Given that finding proper ANN tuning parameters is difficult, the LSA optimization is hybridized with ANN to improve the ANN performances by selecting the optimum values of neurons in each hidden layer and learning rate. Therefore, the ON/OFF estimation accuracy by ANN can be improved. Results of the hybrid LSA-ANN are compared with those of hybrid particle swarm optimization (PSO based ANN to validate the developed algorithm. Results show that the hybrid LSA-ANN outperforms the hybrid PSO based ANN. The proposed scheduling algorithm can significantly reduce the peak-hour energy consumption during the DR event by up to 9.7138% considering four appliances per 7-h period.

Water-Cooled Data Center Packs More Power Per Rack | Poster

Science.gov (United States)

By Frank Blanchard and Ken Michaels, Staff Writers Behind each tall, black computer rack in the data center at the Advanced Technology Research Facility (ATRF) is something both strangely familiar and oddly out of place: It looks like a radiator. The back door of each cabinet is gridded with the coils of the Liebert cooling system, which circulates chilled water to remove heat

Ado Vabbe preemia Anne Parmastole

Index Scriptorium Estoniae

2003-01-01

Tartu Kunstimajas Tartu kunsti aastalõpunäitus. Kujundaja Mari Nõmmela. Anne Parmastole A. Vabbe, Silja Salmistule E-Kunstisalongi, Lii Jürgensonile EDA, Jüri Marranile Wilde kohviku, Sami Makkonenile AS Vunder ja Tartu Õlletehase A. Le Coq ning Eda Lõhmusele AS Merko Tartu preemia

Nuclear fuel rack lateral support and preload device

International Nuclear Information System (INIS)

Knight, C.B.

1979-01-01

A lateral support device for a nuclear fuel rack is described. It is vertically positioned within a walled enclosure which provides a preload to maintain effective support. The device includes a scissors-jack which is mounted so that the drive screw is vertical. Upon rotation of the drive screw the jack expands horizontally, seating a load pad against a vertical wall. The load pad is affixed to the jack by an arm having a stack of spring washers which compress between the pad and the jack, thereby applying a selected preload

AN INTERNET RACK MONITOR-CONTROLLER FOR APS LINAC RF ELECTRONICS UPGRADE

Energy Technology Data Exchange (ETDEWEB)

Ma, Hengjie; Smith, Terry; Nassiri, Alireza; Sun, Yine; Doolittle, Lawrence; Ratti, Alex

2016-06-01

To support the research and development in APS LINAC area, the existing LINAC rf control performance needs to be much improved, and thus an upgrade of the legacy LINAC rf electronics becomes necessary. The proposed upgrade plan centers on the concept of using a modern, network-attached, rackmount digital electronics platform –Internet Rack Monitor-Controller (or IRMC) to achieve the goal of modernizing the rf electronics at a lower cost. The system model of the envisioned IRMC is basically a 3-tier stack with a high-performance DSP in the mid-layer to perform the core tasks of real-time rf data processing and controls. The Digital Front-End (DFE) attachment layer at bottom bridges the applicationspecific rf front-ends to the DSP. A network communication gateway, together with an embedded event receiver (EVR) in the top layer merges the Internet Rack MonitorController node into the networks of the accelerator controls infrastructure. Although the concept is very much in trend with today’s Internet-of-Things (IoT), this implementation has actually been used in the accelerators for over two decades.

Anne Veesaar astus Valgas üles uudses rollis / Jaan Rapp

Index Scriptorium Estoniae

Rapp, Jaan

2010-01-01

2010. aasta iga kuu viimasel reedel esitab näitlejanna Anne Veesaar Raadio Ruudus katkendeid Valgamaa kirjanike loomingust. 14. jaanuaril kohtumisel lugejatega rääkis Valgas sündinud näitlejanna oma elulooraamatust "Anne Veesaar : elus, see on kõige tähtsam", mille on kirja pannud Helen Eelrand, ja oma praegustest tegemistest

Kõnelused Tartus / Anne Untera

Index Scriptorium Estoniae

Untera, Anne, 1951-

2007-01-01

8.-10. V Tartus toimunud eesti, läti ja saksa kunstiteadlaste ühisseminarist. Alexander Knorre rääkis Karl August Senffi, Ilona Audere Friedrich Ludwig von Maydelli, Mai Levin Karl Alexander von Winkleri, Kristiana Abele Johann Walter-Kurau (1869-1932), Anne Untera Konstantin ja Sally von Kügelgeni, Epp Preem Julie Hagen-Schwartzi, Friedrich Gross Eduard von Gebhardti ja Katharina Hadding Ida Kerkoviuse (1879-1970) loomingust

Solar radiation modelling using ANNs for different climates in China

International Nuclear Information System (INIS)

Lam, Joseph C.; Wan, Kevin K.W.; Yang, Liu

2008-01-01

Artificial neural networks (ANNs) were used to develop prediction models for daily global solar radiation using measured sunshine duration for 40 cities covering nine major thermal climatic zones and sub-zones in China. Coefficients of determination (R 2 ) for all the 40 cities and nine climatic zones/sub-zones are 0.82 or higher, indicating reasonably strong correlation between daily solar radiation and the corresponding sunshine hours. Mean bias error (MBE) varies from -3.3 MJ/m 2 in Ruoqiang (cold climates) to 2.19 MJ/m 2 in Anyang (cold climates). Root mean square error (RMSE) ranges from 1.4 MJ/m 2 in Altay (severe cold climates) to 4.01 MJ/m 2 in Ruoqiang. The three principal statistics (i.e., R 2 , MBE and RMSE) of the climatic zone/sub-zone ANN models are very close to the corresponding zone/sub-zone averages of the individual city ANN models, suggesting that climatic zone ANN models could be used to estimate global solar radiation for locations within the respective zones/sub-zones where only measured sunshine duration data are available. (author)

Graphical explanation in an expert system for Space Station Freedom rack integration

Science.gov (United States)

Craig, F. G.; Cutts, D. E.; Fennel, T. R.; Purves, B.

1990-01-01

The rationale and methodology used to incorporate graphics into explanations provided by an expert system for Space Station Freedom rack integration is examined. The rack integration task is typical of a class of constraint satisfaction problems for large programs where expertise from several areas is required. Graphically oriented approaches are used to explain the conclusions made by the system, the knowledge base content, and even at more abstract levels the control strategies employed by the system. The implemented architecture combines hypermedia and inference engine capabilities. The advantages of this architecture include: closer integration of user interface, explanation system, and knowledge base; the ability to embed links to deeper knowledge underlying the compiled knowledge used in the knowledge base; and allowing for more direct control of explanation depth and duration by the user. The graphical techniques employed range from simple statis presentation of schematics to dynamic creation of a series of pictures presented motion picture style. User models control the type, amount, and order of information presented.

Study and project of the new rack with boron for storage of fuel elements burned in the IEA-R1 research reactor

International Nuclear Information System (INIS)

Rodrigues, Antonio Carlos Iglesias; Madi Filho, Tufic; Silva, Davilson Gomes da

2017-01-01

The IEA-R1 research reactor works 40h weekly with 4.5 Mw power. The storage rack for spent fuel elements has less than half of its initial capacity. Under these conditions (current conditions of reactor operation 32h weekly will have 3 spend fuel by year, then, approximately 3 utilization rate Positions/year). Thus, we will have only about six years of capacity for storage. Whereas the desired service life of the IEA-R1 is at least another 20 years, it will be necessary to increase the storage capacity of spent fuel. Hence, it is necessary to double the wet storage capacity (storage in the IEA-R1 reactor's pool). After reviewing the literature about materials available for use in the construction of the new storage rack with absorber of neutrons, the BoralcanTM (manufactured by 3TMhis) was chosen due to its properties. This work presents studies: (a) for the construction of new storages racks with double of the current capacity using the same place of current storages racks and (b) criticality analysis using the MCNP-5 code. Two American Nuclear Data Library were used: ENDF / B-VI and ENDF / B-VII, and the results obtained for each data bases were compared. These analyzes confirm the possibility of doubling the storage capacity of fuel elements burned in the same place occupied by the current storage rack attending to the IEA-R1 reactor needs and attending the safety requirements according to the National Nuclear Energy Commission - CNEN and the International Atomic Energy Agency (IAEA). To calculate the k eff were considered new fuel elements (maximum possible reactivity) used in full charge of the storage rack. With the results obtained in the simulation we can conclude that doubling the amount of racks for spent fuel elements are complied with safety limits established in the IAEA standards and CNEN of criticality (keff < 0.95). (author)

Study and project of the new rack with boron for storage of fuel elements burned in the IEA-R1 research reactor

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, Antonio Carlos Iglesias; Madi Filho, Tufic; Silva, Davilson Gomes da, E-mail: acirodri@ipen.br, E-mail: tmfilho@usp.br, E-mail: dgsilva@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

2017-07-01

The IEA-R1 research reactor works 40h weekly with 4.5 Mw power. The storage rack for spent fuel elements has less than half of its initial capacity. Under these conditions (current conditions of reactor operation 32h weekly will have 3 spend fuel by year, then, approximately 3 utilization rate Positions/year). Thus, we will have only about six years of capacity for storage. Whereas the desired service life of the IEA-R1 is at least another 20 years, it will be necessary to increase the storage capacity of spent fuel. Hence, it is necessary to double the wet storage capacity (storage in the IEA-R1 reactor's pool). After reviewing the literature about materials available for use in the construction of the new storage rack with absorber of neutrons, the BoralcanTM (manufactured by 3TMhis) was chosen due to its properties. This work presents studies: (a) for the construction of new storages racks with double of the current capacity using the same place of current storages racks and (b) criticality analysis using the MCNP-5 code. Two American Nuclear Data Library were used: ENDF / B-VI and ENDF / B-VII, and the results obtained for each data bases were compared. These analyzes confirm the possibility of doubling the storage capacity of fuel elements burned in the same place occupied by the current storage rack attending to the IEA-R1 reactor needs and attending the safety requirements according to the National Nuclear Energy Commission - CNEN and the International Atomic Energy Agency (IAEA). To calculate the k{sub eff} were considered new fuel elements (maximum possible reactivity) used in full charge of the storage rack. With the results obtained in the simulation we can conclude that doubling the amount of racks for spent fuel elements are complied with safety limits established in the IAEA standards and CNEN of criticality (keff < 0.95). (author)

Lactobacillus casei triggers a TLR mediated RACK-1 dependent p38 MAPK pathway in Caenorhabditis elegans to resist Klebsiella pneumoniae infection.

Science.gov (United States)

Kamaladevi, Arumugam; Balamurugan, Krishnaswamy

2016-07-13

In the present study, the effect of Lactic Acid Bacteria (LAB) was investigated at the molecular level using the model organism Caenorhabditis elegans against Klebsiella pneumoniae. Out of the 13 LAB screened, Lactobacillus casei displayed excellent protective efficacy by prolonging the survival of K. pneumoniae-infected nematodes. Pretreatment with L. casei significantly decreased bacterial colonization and rescued K. pneumoniae-infected C. elegans from various physiological impairments. The concomitant upregulation of key immune genes that regulate the TLR, RACK-1 as well as the p38 MAPK pathway rather than the IIS and ERK pathway suggested that the plausible immunomodulatory mechanism of L. casei could be by triggering the TLR, RACK-1 and p38 MAPK pathway. Furthermore, the hyper-susceptibility of L. casei treated loss-of-function mutants of the tol-1, RACK-1 and p38 MAPK pathway (sek-1 and pmk-1) to K. pneumoniae infection and gene expression analysis suggested that L. casei triggered a TLR mediated RACK-1 dependent p38 MAPK pathway to increase host resistance and protect nematodes against K. pneumoniae infection.

Improvement of rotary specimen rack design

International Nuclear Information System (INIS)

Batch, J.M.; Gietzen, A.J.

1978-01-01

A redesign and verification test program has been completed on a new Rotary Specimen Rack ('Lazy Susan') design for the TRIGA Mark III. The purpose of the redesign was to solve a rotation problem which occurred at power levels of about 1 MW and above. The previous redesign effort on the Mark II-type lazy susan was made in 1967 when the bearing was changed to use stellite balls, spring-type separators and stainless-steel bearing races. An extensive test program at that time showed that the design gave excellent service under all anticipated operating conditions. Fifteen of these units have been installed in the past ten years and have been essentially trouble-free. Although the bearing design for the Mark III was very similar, the component layout was such that irradiation-induced heating with associated thermal expansion resulted in decreased bearing clearance and an increase in the required driving torque. The solution involved redesign and re-arrangement of the rack drive mechanism. A series of stringent operational proof tests were made under high temperature and temperature differential conditions which proved successful operation of the new design. The severe conditions under which these tests were performed uncovered further difficulties with the bearing and led to a re-evaluation of the bearing design. A new design was developed in which the spring separators were replaced by similar sized, cylindrical graphite spacers. The entire series of operational and life tests were repeated and the performance was outstanding. Acceptable wear characteristics of the spacers were verified and the bearing was noticeably smoother and quieter than with previous designs. A Mark III lazy susan of this new design was installed in a TRIGA about one year ago and operated at power levels up to 2 MW with excellent performance. The Mark II design has now been changed to incorporate the new drive and bearing design proven for the Mark III. (author)

Metal-driven and covalent synthesis of supramolecular grids from racks: a convergent approach to heterometallic and heteroleptic nanostructures.

Science.gov (United States)

Schmittel, Michael; Kalsani, Venkateshwarlu; Bats, Jan W

2005-06-13

Supramolecular nanogrids were prepared from dynamic supramolecular racks through the coupling of terminal alkynes using either a covalent (with CuCl/O(2)) or a coordinative (with [trans-(PEt(3))(2)PtCl(2)]) approach. Because of the rapid equilibration of the racks (as tested by exchange reactions), oligomeric adducts potentially formed in the coupling process will selectively furnish the nanogrids through an entropically driven self-repair mechanism. To ascertain the structural assignment, the nanogrids were also synthesized by an independent strategy.

Design of a new wet storage rack for spent fuels from IEA-R1 reactor

International Nuclear Information System (INIS)

Rodrigues, Antonio C.I.; Madi Filho, Tufic; Siqueira, Paulo T.D.; Ricci Filho, Walter

2015-01-01

The IEA-R1 research reactor operates in a regimen of 64h weekly, at the power of 4.5 MW. In these conditions, the racks of the spent fuel elements have less than half of its initial capacity. Thus, maintaining these operating conditions, the storage will have capacity for about six years. Since the estimated useful life of the IEA-R1 is about another 20 years, it will be necessary to increase the storage capacity of spent fuel. Dr. Henrik Grahn, expert of the International Atomic Energy Agency on wet storage, visiting the IEA-R1 Reactor (September/2012) made some recommendations: among them, the design and installation of racks made with borated stainless steel and internally coated with an aluminum film, so that corrosion of the fuel elements would not occur. After an extensive literature review of material options given for this type of application we got to Boral® manufactured by 3M due to numerous advantages. This paper presents studies on the analysis of criticality using the computer code MCNP 5, demonstrating the possibility of doubling the storage capacity of current racks to attend the demand of the IEA-R1 reactor while attending the safety requirements the International Atomic Energy Agency. (author)

Design of a new wet storage rack for spent fuels from IEA-R1 reactor

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, Antonio C.I.; Madi Filho, Tufic; Siqueira, Paulo T.D.; Ricci Filho, Walter, E-mail: acirodri@ipen.br, E-mail: tmfilho@ipen.br, E-mail: ptsiquei@ipen.br, E-mail: wricci@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2015-07-01

The IEA-R1 research reactor operates in a regimen of 64h weekly, at the power of 4.5 MW. In these conditions, the racks of the spent fuel elements have less than half of its initial capacity. Thus, maintaining these operating conditions, the storage will have capacity for about six years. Since the estimated useful life of the IEA-R1 is about another 20 years, it will be necessary to increase the storage capacity of spent fuel. Dr. Henrik Grahn, expert of the International Atomic Energy Agency on wet storage, visiting the IEA-R1 Reactor (September/2012) made some recommendations: among them, the design and installation of racks made with borated stainless steel and internally coated with an aluminum film, so that corrosion of the fuel elements would not occur. After an extensive literature review of material options given for this type of application we got to Boral® manufactured by 3M due to numerous advantages. This paper presents studies on the analysis of criticality using the computer code MCNP 5, demonstrating the possibility of doubling the storage capacity of current racks to attend the demand of the IEA-R1 reactor while attending the safety requirements the International Atomic Energy Agency. (author)

LFC based adaptive PID controller using ANN and ANFIS techniques

Directory of Open Access Journals (Sweden)

Mohamed I. Mosaad

2014-12-01

Full Text Available This paper presents an adaptive PID Load Frequency Control (LFC for power systems using Neuro-Fuzzy Inference Systems (ANFIS and Artificial Neural Networks (ANN oriented by Genetic Algorithm (GA. PID controller parameters are tuned off-line by using GA to minimize integral error square over a wide-range of load variations. The values of PID controller parameters obtained from GA are used to train both ANFIS and ANN. Therefore, the two proposed techniques could, online, tune the PID controller parameters for optimal response at any other load point within the operating range. Testing of the developed techniques shows that the adaptive PID-LFC could preserve optimal performance over the whole loading range. Results signify superiority of ANFIS over ANN in terms of performance measures.

Plasmonic rack-and-pinion gear with chiral metasurface

Science.gov (United States)

Gorodetski, Yuri; Karabchevsky, Alina

2016-04-01

The effect of circularly polarized beaming excited by traveling surface plasmons, via chiral metasurface is experimentally studied. Here we show that the propagation direction of the plasmonic wave, evanescently excited on the thin gold film affects the handedness of the scattered beam polarization. Nanostructured metasurface leads to excitation of localized plasmonic modes whose relative spatial orientation induces overall spin-orbit interaction. This effect is analogical to the rack-and-pinion gear: the rotational motion into the linear motion converter. From the practical point of view, the observed effect can be utilized in integrated optical circuits for communication systems, cyber security and sensing.

Flow forecast by SWAT model and ANN in Pracana basin, Portugal

NARCIS (Netherlands)

Demirel, M.C.; Venancio, Anabela; Kahya, Ercan

2009-01-01

This study provides a unique opportunity to analyze the issue of flow forecast based on the soil and water assessment tool (SWAT) and artificial neural network (ANN) models. In last two decades, the ANNs have been extensively applied to various water resources system problems. In this study, the

C-188 Co-60 sources installation and source rack loading optimization processes in a gamma irradiation facility

Energy Technology Data Exchange (ETDEWEB)

Santos, Paulo de S.; Vasquez, Pablo A.S., E-mail: psantos@ipen.br, E-mail: pavsalva@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2017-11-01

Since 2004, the Multipurpose Gamma Facility at the Nuclear and Energy Research Institute has been providing services on radiation processing for disinfection and sterilization of health care and disposable medical products as well to support research studies on modification of physical, chemical and biological properties of several materials. Recently, there was an increment in irradiation of the Cultural Heritages. This facility uses C-188 double-encapsulated radioactive Cobalt-60 sources known as pencils from manufactures outside of country. The activity of the cobalt sources decays into a stable nickel isotope with a half-life around 5.27 years, which means a loss of 12.3% annually. Then, additional pencils of Cobalt-60 are added periodically to the source rack to maintain the required capacity or installed activity of the facility. The manufacturer makes shipping of the radioactive sources inside a high density container type B(U) , by sea. This one involves many administrative, transport and radiation safety procedures. Once in the facility, the container is opened inside a deep pool water to remove the pencils. The required source geometry of the facility is obtained by loading these source pencils into predetermined diagram or positions in source modules and distributing these modules over the source rack of the facility. The dose variation can be reduced placing the higher activity source pencils near the periphery of the source rack. In this work are presented the procedures for perform the boiling leaching tests applied to the container, the Cobalt-60 sources installation, the loading processes and the source rack loading optimization. (author)

Nuclear criticality safety: general. 6. Application of Fixed Neutron Absorbers in the New Hanford PFP Horizontal Rack Design

International Nuclear Information System (INIS)

Lan, J.S.; Miller, E.M.; Toffer, H.; Mo, B.S.

2001-01-01

The Hanford Plutonium Finishing Plant (PFP) is currently in a waste cleanup and plutonium stabilization mode. Plutonium-bearing materials are processed through thermal treatment, creating forms of oxides suitable for long-term storage. Stabilized materials at PFP are stored in a variety of cans such as the bag-less transfer cans (BTCs), which are ultimately contained in the U.S. Department of Energy (DOE) 3013 can; both cans are larger than previously used plutonium storage containers and hold more plutonium. To compensate for the increased plutonium loadings, added engineered safety features were considered in the storage facilities. The vaults in PFP, subdivided into concrete-walled cubicles, will contain both new and older cans. The DOE 3013 and BTC cans may be loaded with up to 4.4 kg of plutonium as a compound (mostly oxide). New racks that store cans horizontally are being constructed to hold both new and older containers. The loading objective is to accommodate 70 kg of plutonium per cubicle. Two design analysis approaches for the new racks were considered. The first approach incorporated neutron absorption provided by the structural materials of the rack and the cans in determining a safe configuration. A rack loading arrangement was determined as shown in Fig. 1 and specified in Table I. This approach provides compliance with criticality control requirements; however, added administrative controls were needed to accommodate a sufficient number of cans in specific locations to achieve 70 kg of plutonium per cubicle. The 4.4-kg plutonium container can be placed only in predetermined locations. The second approach evaluated the addition of a fixed neutron absorber plate along the back wall of the cubicle (Fig. 1). The location of the special plate facilitates installation of the racks and provides additional criticality safety margin beyond the first approach. Its presence permits loading of racks with up to 4.4-kg plutonium cans in any storage locations

Parametric Evaluation of Racking Performance of Platform Timber Framed Walls

OpenAIRE

Dhonju, R..; D’Amico, B..; Kermani, A..; Porteous, J..; Zhang, B..

2017-01-01

This paper provides a quantitative assessment of the racking performance of partially anchored timber framed walls, based on experimental tests. A total of 17 timber framed wall specimens, constructed from a combination of materials under different load configurations, were tested. The experimental study was designed toexamine the influence of a range of geometrical parameters, such as fastener size and spacings, wall length, arrangement of studs and horizontal members, as well as the effect ...

Identification of drought in Dhalai river watershed using MCDM and ANN models

Science.gov (United States)

Aher, Sainath; Shinde, Sambhaji; Guha, Shantamoy; Majumder, Mrinmoy

2017-03-01

An innovative approach for drought identification is developed using Multi-Criteria Decision Making (MCDM) and Artificial Neural Network (ANN) models from surveyed drought parameter data around the Dhalai river watershed in Tripura hinterlands, India. Total eight drought parameters, i.e., precipitation, soil moisture, evapotranspiration, vegetation canopy, cropping pattern, temperature, cultivated land, and groundwater level were obtained from expert, literature and cultivator survey. Then, the Analytic Hierarchy Process (AHP) and Analytic Network Process (ANP) were used for weighting of parameters and Drought Index Identification (DII). Field data of weighted parameters in the meso scale Dhalai River watershed were collected and used to train the ANN model. The developed ANN model was used in the same watershed for identification of drought. Results indicate that the Limited-Memory Quasi-Newton algorithm was better than the commonly used training method. Results obtained from the ANN model shows the drought index developed from the study area ranges from 0.32 to 0.72. Overall analysis revealed that, with appropriate training, the ANN model can be used in the areas where the model is calibrated, or other areas where the range of input parameters is similar to the calibrated region for drought identification.

GreenChill Store Certification Protocol for Sub-Cooling Contained on Racks Separate from Refrigeration Equipment

Science.gov (United States)

Document describes the protocol used to determine the total load and refrigerant charge of stores that have placed all sub-cooling on a rack separate from all other commercial refrigeration equipment.

A Fragment of the Past: The System of Hotel Front Office Racks

Directory of Open Access Journals (Sweden)

Peter Szende

2017-06-01

Full Text Available Before computers and electronic systems, the heart of a hotel's front desk was a metal file system which consisted of pockets for the slips to be inserted into, called the room rack. Take a step back in time to see how these efficient systems were developed and adapted by different hotel properties.

Random Access Frames (RAF): Alternative to Rack and Standoff for Deep Space Habitat Outfitting

Science.gov (United States)

Howe, A. Scott; Polit-Casillas, Raul

2014-01-01

A modular Random Access Frame (RAF) system is proposed as an alternative to the International Standard Payload Rack (ISPR) for internal module layout and outfitting in a Deep Space Habitat (DSH). The ISPR approach was designed to allow for efficient interchangeability of payload and experiments for the International Space Station (ISS) when frequent resupply missions were available (particularly the now-retired Space Shuttle). Though the standard interface approach to the ISPR system allowed integration of subsystems and hardware from a variety of sources and manufacturers, the heavy rack and standoff approach may not be appropriate when resupply or swap-out capabilities are not available, such as on deep space, long-duration missions. The lightweight RAF concept can allow a more dense packing of stowage and equipment, and may be easily broken down for repurposing or reuse. Several example layouts and workstations are presented.

Spent fuel storage rack for BWR fuel assemblies

International Nuclear Information System (INIS)

Machado, O.; Henry, C.W.; Congleton, R.L.; Flynn, W.M.

1990-01-01

This patent describes for the use in storing nuclear fuel assemblies in a storage pool containing a coolant and having a pool floor, a fuel rack module. It comprises: a base plate to be disposed generally horizontally on the floor and having a horizontal surface area sufficient to support a fuel assemblies; uniformly spaced openings in the base plate, disposed in rows and columns throughout the surface area; fabricated cells of rectangular cross section extending over alternate openings along each row of the openings, the fabricated cells of each row being uniformly staggered by one opening with respect to the cells of its just adjacent rows so that the fabricated cells form a checkerboard like array; each of the fabricated cells having elongated walls mounted generally vertically on the base plate; each of the corners formed by the walls of each fabricated cell, which corners are internal of the periphery of the array, being disposed as closely adjacent as practicable to and face-to-face with a corner of an adjacent fabricated cell and joined by weld means so that substantially no space exists between adjacent cells. The cells being welded to their bottom ends to the base plate so that a strong compact modular structure is produced; neutron-absorbing means on the external surface of the fabricated cell walls except on the coextensive sections of the outer wall around the periphery of the array; and leveling pads are mounted under the base plate near the periphery thereof and adjustably engage the pool floor and intermediate leveling pads are mounted under cells within the fuel-rack module, the intermediate pads being uniformly disposed

Mathematical Modelling of Involute Spur Gears Manufactured by Rack Cutter

Directory of Open Access Journals (Sweden)

Tufan Gürkan YILMAZ

2016-05-01

Full Text Available In this study, mathematical modelling of asymmetric involute spur gears was situated in by Litvin approach. In this context, firstly, mathematical expressions of rack cutter which manufacture asymmetric involute spur gear, then mathematical expression of asymmetric involute spur gear were obtained by using differential geometry, coordinate transformation and gear theory. Mathematical expressions were modelled in MATLAB and output files including points of involute spur gear’s teeth were designed automatically thanks to macros.

Ann Arbor Session I: Breaking Ground.

Science.gov (United States)

Music Educators Journal, 1979

1979-01-01

Summarizes the first session of the National Symposium on the Applications of Psychology to the Teaching and Learning of Music held at Ann Arbor from October 30 to November 2, 1978. Sessions concerned auditory perception, motor learning, child development, memory and information processing, and affect and motivation. (SJL)

Morphometrics and structure of complete baleen racks in gray whales (Eschrichtius robustus) from the Eastern North Pacific Ocean.

Science.gov (United States)

Young, Samantha; DeméRé, Thomas A; Ekdale, Eric G; Berta, Annalisa; Zellmer, Nicholas

2015-04-01

Mysticetes have evolved a novel filter feeding apparatus-baleen-an epidermal keratinous tissue composed of keratin that grows as a serial arrangement of transverse cornified laminae from the right and left sides of the palate. The structure and function of baleen varies among extant mysticete clades and this variation likely can be viewed as adaptations related to different filter feeding strategies. In one of the first morphometric studies of the full baleen apparatus, we describe the morphology of complete baleen racks in neonate, yearling and adult gray whales (Eschrichtius robustus), and note morphometric variations between age groups as well as within individual racks. Morphometric data and detailed descriptions were collected from the full baleen apparatus of three frozen specimens of E. robustus using previously derived ecologically significant and broad scale measurements of baleen. Additionally, characters of the baleen apparatus were described based on visible patterns of baleen laminae and plates on the dorsal root of the rack. Results indicate that the longest, widest, and thickest plates and laminae are found toward the posterior half of the rack, resulting in the greatest surface area for filtration of prey occurring in this region. Ontogenetic changes were also documented that reveal a progressive increase in the filter surface area of the developing baleen apparatus as baleen laminae and main plates grow in length and width. Also noted was a progressive posterior shift in the position of greatest filtration area. Histological examination of the epithelial base (Zwischensubstanz) and laminae showed basic epidermal layers, as well as gapping between layers and vacuoles. © 2015 Wiley Periodicals, Inc.

ANN based optimization of a solar assisted hybrid cooling system in Turkey

Energy Technology Data Exchange (ETDEWEB)

Ozgur, Arif; Yetik, Ozge; Arslan, Oguz [Mechanical Eng. Dept., Engineering Faculty, Dumlupinar University (Turkey)], email: maozgur@dpu.edu.tr, email: ozgeyetik@dpu.edu.tr, email: oarslan@dpu.edu.tr

2011-07-01

This study achieved optimization of a solar assisted hybrid cooling system with refrigerants such as R717, R141b, R134a and R123 using an artificial neural network (ANN) model based on average total solar radiation, ambient temperature, generator temperature, condenser temperature, intercooler temperature and fluid types. ANN is a new tool; it works rapidly and can thus be a solution for design and optimization of complex power cycles. A unique flexible ANN algorithm was introduced to evaluate the solar ejector cooling systems because of the nonlinearity of neural networks. The conclusion was that the best COPs value obtained with the ANN is 1.35 and COPc is 3.03 when the average total solar radiation, ambient temperature, generator temperature, condenser temperature, intercooler temperature and algorithm are respectively 674.72 W/m2, 17.9, 80, 15 and 13 degree celsius and LM with 14 neurons in single hidden layer, for R717.

A Hybrid FEM-ANN Approach for Slope Instability Prediction

Science.gov (United States)

Verma, A. K.; Singh, T. N.; Chauhan, Nikhil Kumar; Sarkar, K.

2016-09-01

Assessment of slope stability is one of the most critical aspects for the life of a slope. In any slope vulnerability appraisal, Factor Of Safety (FOS) is the widely accepted index to understand, how close or far a slope from the failure. In this work, an attempt has been made to simulate a road cut slope in a landslide prone area in Rudrapryag, Uttarakhand, India which lies near Himalayan geodynamic mountain belt. A combination of Finite Element Method (FEM) and Artificial Neural Network (ANN) has been adopted to predict FOS of the slope. In ANN, a three layer, feed- forward back-propagation neural network with one input layer and one hidden layer with three neurons and one output layer has been considered and trained using datasets generated from numerical analysis of the slope and validated with new set of field slope data. Mean absolute percentage error estimated as 1.04 with coefficient of correlation between the FOS of FEM and ANN as 0.973, which indicates that the system is very vigorous and fast to predict FOS for any slope.

Comparison of Conventional and ANN Models for River Flow Forecasting

Science.gov (United States)

Jain, A.; Ganti, R.

2011-12-01

Hydrological models are useful in many water resources applications such as flood control, irrigation and drainage, hydro power generation, water supply, erosion and sediment control, etc. Estimates of runoff are needed in many water resources planning, design development, operation and maintenance activities. River flow is generally estimated using time series or rainfall-runoff models. Recently, soft artificial intelligence tools such as Artificial Neural Networks (ANNs) have become popular for research purposes but have not been extensively adopted in operational hydrological forecasts. There is a strong need to develop ANN models based on real catchment data and compare them with the conventional models. In this paper, a comparative study has been carried out for river flow forecasting using the conventional and ANN models. Among the conventional models, multiple linear, and non linear regression, and time series models of auto regressive (AR) type have been developed. Feed forward neural network model structure trained using the back propagation algorithm, a gradient search method, was adopted. The daily river flow data derived from Godavari Basin @ Polavaram, Andhra Pradesh, India have been employed to develop all the models included here. Two inputs, flows at two past time steps, (Q(t-1) and Q(t-2)) were selected using partial auto correlation analysis for forecasting flow at time t, Q(t). A wide range of error statistics have been used to evaluate the performance of all the models developed in this study. It has been found that the regression and AR models performed comparably, and the ANN model performed the best amongst all the models investigated in this study. It is concluded that ANN model should be adopted in real catchments for hydrological modeling and forecasting.

Field Trial on a Rack-mounted DC Power Supply System with 80-Ah Lithium-ion Batteries

Science.gov (United States)

Matsushima, Toshio

Using an industrial lithium-ion battery that has higher energy density than conventional valve-regulated lead-acid batteries, a rack-mounted DC-power-supply system was assembled and tested at a base transceiver station (BTS) offering actual services. A nominal output voltage and maximum output current of the system is 53.5V and 20A, respectively. An 80-Ah lithium-ion battery composed of 13 cells connected in series was applied in the system and maintained in a floating charge method. The DC-power-supply system was installed in a 19-inch power rack in the telecommunications equipment box at BTS. The characteristics of the 80Ah lithium-ion battery, specifications of the DC-power-supply system and field-test results were shown in this paper.

Conceptual design of reactor TRIGA PUSPATI (RTP) spent fuel storage rack

International Nuclear Information System (INIS)

Tonny Lanyau; Mohd Fazli Zakaria; Zaredah Hashim; Ahmad Nabil Ab Rahim; Mohammad Suhaimi Kassim

2010-01-01

PUSPATI TRIGA Reactor (RTP) is a pool type research reactor with 1MW thermal power. It has been safely operated since 28 June 1982. During 28 years of safe operation, there are several systems and components of the RTP that have been maintained, repaired, upgraded and replaced in order to maintain its function and safety conditions. RTP has been proposed to be upgraded so that optimum operation of RTP could be achieved as well as fulfill the future needs. Thus, competencies and technical capabilities were needed to design and develop the reactor system. In the meantime, there is system or component need to be maintained such as fuel elements. Since early operation, most of the fuel elements still can be used and none of the fuel elements was replaced or sent for reprocessing and final disposal. Towards the power upgrading, preparation of spent fuel storage is needed for temporary storing of the fuels discharged from the reactor core. The spent fuel storage rack will be located in the spent fuel pool to accommodate the spent fuels before it is send to reprocessing or final disposal. This paper proposes the conceptual design of the spent fuel storage rack. The output of this paper focused on the physical and engineering design of the spent fuel storage. (author)

Annäherung Approaching

Directory of Open Access Journals (Sweden)

Carola Hilmes

2007-03-01

Full Text Available Das von Stefan Moses zusammengestellte „Bilderbuch“ zeigt Fotos von Ilse Aichinger. Sie selbst kommt durch eine Reihe von Geschichten und Gedichten zu Wort. In diesen intimen Dialog werden auch die Leser/-innen einbezogen. Das ermöglicht Annäherung.This “Picture Book”, compiled by Stefan Moses, displays photographs of Ilse Aichinger. She is also given voice through a series of stories and poems. The reader is also drawn into this intimate dialogue, thus making it possible for image, text, and reader to converge.

ANN-based wavelet analysis for predicting electrical signal from photovoltaic power supply system

Energy Technology Data Exchange (ETDEWEB)

Mellit, A. [Medea Univ., Medea (Algeria). Inst. of Science Engineering, Dept. of Electronics

2007-07-01

This study was conducted to predict different electrical signals from a photovoltaic power supply system (PVPS) using an artificial neural networks (ANN) with wavelet analysis. It involved the creation of a database of electrical signals (PV-generator current, voltage, battery current voltage, regulator current and voltage) obtained from an experimental PVPS system installed in the south of Algeria. The potential applications were for sizing and analyzing the performance of PVPS systems; control of maximum power point tracker (MPPT) in order to deliver the maximum energy from the PV-array; prediction of the optimal configuration (PV-array and battery sizing) of PVPS systems; expert configuration of PV-systems; faults diagnosis; supervision; and, control and monitoring. First, based on the wavelet analysis each electrical signal was mapped in several time frequency domains. The PV-system was then divided into 3-subsystems corresponding to ANN-PV generator model, ANN-battery model, and ANN-regulator model. An example of day-by-day prediction for each electrical signal was presented. The results of the proposed approach were in good agreement with experimental results. In addition, the accuracy of the proposed approach was more satisfactory when only ANN was used. It was concluded that this methodology offers the possibility of developing a new expert configuration of PVPS by implementing the soft computing ANN-wavelet program with a digital signal processing (DSP) circuit. 26 refs., 1 tab., 5 figs.

Visual NNet: An Educational ANN's Simulation Environment Reusing Matlab Neural Networks Toolbox

Science.gov (United States)

Garcia-Roselló, Emilio; González-Dacosta, Jacinto; Lado, Maria J.; Méndez, Arturo J.; Garcia Pérez-Schofield, Baltasar; Ferrer, Fátima

2011-01-01

Artificial Neural Networks (ANN's) are nowadays a common subject in different curricula of graduate and postgraduate studies. Due to the complex algorithms involved and the dynamic nature of ANN's, simulation software has been commonly used to teach this subject. This software has usually been developed specifically for learning purposes, because…

Ehe seep Eesti moodi / Anneli Aasmäe

Index Scriptorium Estoniae

Aasmäe, Anneli, 1973-

2008-01-01

Produtsent Kristian Taska Kalev Spordis näidatav Venezuela seebiseriaali Eesti oludele mugandatud variant "Kalevi naised" : lavastaja Ingomar Vihman : osades Andrus Vaarik, Anne Reemann, Piret Kalda, Ken Saan jt.

Fixing Trailer Hitch for Roof Rack of Cargos

Directory of Open Access Journals (Sweden)

Darina Matisková

2017-02-01

Full Text Available This article presents a new technical solution of fixing trailer hitch which serves as a connection between single track vehicle and cargo, mainly light trailer. They are manufactured from steel girder and nets which are constructed by point welding. They are designed to indicate the necessary solidity and the required load bearing capacity of the cargo. The application of roof racks is universal and these products are in great demand in the field of game management. There are a lot of trailer hitches which the manufacturers tailor to customers´ demands. The stated technical solution is subject of published industrial utility model at the Industrial property office of the Slovak republic.

Simulation model of ANN based maximum power point tracking controller for solar PV system

Energy Technology Data Exchange (ETDEWEB)

Rai, Anil K.; Singh, Bhupal [Department of Electrical and Electronics Engineering, Ajay Kumar Garg Engineering College, Ghaziabad 201009 (India); Kaushika, N.D.; Agarwal, Niti [School of Research and Development, Bharati Vidyapeeth College of Engineering, A-4 Paschim Vihar, New Delhi 110063 (India)

2011-02-15

In this paper the simulation model of an artificial neural network (ANN) based maximum power point tracking controller has been developed. The controller consists of an ANN tracker and the optimal control unit. The ANN tracker estimates the voltages and currents corresponding to a maximum power delivered by solar PV (photovoltaic) array for variable cell temperature and solar radiation. The cell temperature is considered as a function of ambient air temperature, wind speed and solar radiation. The tracker is trained employing a set of 124 patterns using the back propagation algorithm. The mean square error of tracker output and target values is set to be of the order of 10{sup -5} and the successful convergent of learning process takes 1281 epochs. The accuracy of the ANN tracker has been validated by employing different test data sets. The control unit uses the estimates of the ANN tracker to adjust the duty cycle of the chopper to optimum value needed for maximum power transfer to the specified load. (author)

Optimization of Nd: YAG Laser Marking of Alumina Ceramic Using RSM And ANN

International Nuclear Information System (INIS)

Peter, Josephine; Doloi, B.; Bhattacharyya, B.

2011-01-01

The present research papers deals with the artificial neural network (ANN) and the response surface methodology (RSM) based mathematical modeling and also an optimization analysis on marking characteristics on alumina ceramic. The experiments have been planned and carried out based on Design of Experiment (DOE). It also analyses the influence of the major laser marking process parameters and the optimal combination of laser marking process parametric setting has been obtained. The output of the RSM optimal data is validated through experimentation and ANN predictive model. A good agreement is observed between the results based on ANN predictive model and actual experimental observations.

Combat Ration Network for Technology Implementation. Retort Racks for Polymeric Trays in 1400 Style Spray Retorts

National Research Council Canada - National Science Library

Bruins, Henderikus B; Coburn, John F

2003-01-01

The objective of this project was to design a retort rack that would maximize the retort capacity of a 1400 style spray retort and to select a material that would withstand the harsh retort spray environment...

Klaas ja mõis / Maie-Ann Raun

Index Scriptorium Estoniae

Raun, Maie-Ann, 1938-

2007-01-01

Klaasikunstinäitus "Ringkäik" Albu mõisas, kuraatorid Virve Kiil, Kati Kerstna, Kairi Orgusaar. Eksponeeritakse Tiina Sarapu, Mare Saare, Eeva Käsperi, Kai Kiudsoo-Värvi, Pilvi Ojamaa, Merle Bukoveci, Kalli Seina, Viivi-Ann Keerdo, Liisi Junolaineni, Kristiina Uslari, Ivo Lille töid

Prediction of Splitting Tensile Strength of Concrete Containing Zeolite and Diatomite by ANN

Directory of Open Access Journals (Sweden)

E. Gülbandılar

2017-01-01

Full Text Available This study was designed to investigate with two different artificial neural network (ANN prediction model for the behavior of concrete containing zeolite and diatomite. For purpose of constructing this model, 7 different mixes with 63 specimens of the 28, 56 and 90 days splitting tensile strength experimental results of concrete containing zeolite, diatomite, both zeolite and diatomite used in training and testing for ANN systems was gathered from the tests. The data used in the ANN models are arranged in a format of seven input parameters that cover the age of samples, Portland cement, zeolite, diatomite, aggregate, water and hyper plasticizer and an output parameter which is splitting tensile strength of concrete. In the model, the training and testing results have shown that two different ANN systems have strong potential as a feasible tool for predicting 28, 56 and 90 days the splitting tensile strength of concrete containing zeolite and diatomite.

Application of ANN-SCE model on the evaluation of automatic generation control performance

Energy Technology Data Exchange (ETDEWEB)

Chang-Chien, L.R.; Lo, C.S.; Lee, K.S. [National Cheng Kung Univ., Tainan, Taiwan (China)

2005-07-01

An accurate evaluation of load frequency control (LFC) performance is needed to balance minute-to-minute electricity generation and demand. In this study, an artificial neural network-based system control error (ANN-SCE) model was used to assess the performance of automatic generation controls (AGC). The model was used to identify system dynamics for control references in supplementing AGC logic. The artificial neural network control error model was used to track a single area's LFC dynamics in Taiwan. The model was used to gauge the impacts of regulation control. Results of the training, evaluating, and projecting processes showed that the ANN-SCE model could be algebraically decomposed into components corresponding to different impact factors. The SCE information obtained from testing of various AGC gains provided data for the creation of a new control approach. The ANN-SCE model was used in conjunction with load forecasting and scheduled generation data to create an ANN-SCE identifier. The model successfully simulated SCE dynamics. 13 refs., 10 figs.

Groundwater Pollution Source Identification using Linked ANN-Optimization Model

Science.gov (United States)

Ayaz, Md; Srivastava, Rajesh; Jain, Ashu

2014-05-01

Groundwater is the principal source of drinking water in several parts of the world. Contamination of groundwater has become a serious health and environmental problem today. Human activities including industrial and agricultural activities are generally responsible for this contamination. Identification of groundwater pollution source is a major step in groundwater pollution remediation. Complete knowledge of pollution source in terms of its source characteristics is essential to adopt an effective remediation strategy. Groundwater pollution source is said to be identified completely when the source characteristics - location, strength and release period - are known. Identification of unknown groundwater pollution source is an ill-posed inverse problem. It becomes more difficult for real field conditions, when the lag time between the first reading at observation well and the time at which the source becomes active is not known. We developed a linked ANN-Optimization model for complete identification of an unknown groundwater pollution source. The model comprises two parts- an optimization model and an ANN model. Decision variables of linked ANN-Optimization model contain source location and release period of pollution source. An objective function is formulated using the spatial and temporal data of observed and simulated concentrations, and then minimized to identify the pollution source parameters. In the formulation of the objective function, we require the lag time which is not known. An ANN model with one hidden layer is trained using Levenberg-Marquardt algorithm to find the lag time. Different combinations of source locations and release periods are used as inputs and lag time is obtained as the output. Performance of the proposed model is evaluated for two and three dimensional case with error-free and erroneous data. Erroneous data was generated by adding uniformly distributed random error (error level 0-10%) to the analytically computed concentration

Prediction of Film Cooling Effectiveness on a Gas Turbine Blade Leading Edge Using ANN and CFD

Science.gov (United States)

Dávalos, J. O.; García, J. C.; Urquiza, G.; Huicochea, A.; De Santiago, O.

2018-05-01

In this work, the area-averaged film cooling effectiveness (AAFCE) on a gas turbine blade leading edge was predicted by employing an artificial neural network (ANN) using as input variables: hole diameter, injection angle, blowing ratio, hole and columns pitch. The database used to train the network was built using computational fluid dynamics (CFD) based on a two level full factorial design of experiments. The CFD numerical model was validated with an experimental rig, where a first stage blade of a gas turbine was represented by a cylindrical specimen. The ANN architecture was composed of three layers with four neurons in hidden layer and Levenberg-Marquardt was selected as ANN optimization algorithm. The AAFCE was successfully predicted by the ANN with a regression coefficient R2<0.99 and a root mean square error RMSE=0.0038. The ANN weight coefficients were used to estimate the relative importance of the input parameters. Blowing ratio was the most influential parameter with relative importance of 40.36 % followed by hole diameter. Additionally, by using the ANN model, the relationship between input parameters was analyzed.

Quick and reliable estimation of power distribution in a PHWR by ANN

International Nuclear Information System (INIS)

Dubey, B.P.; Jagannathan, V.; Kataria, S.K.

1998-01-01

Knowledge of the distribution of power in all the channels of a Pressurised Heavy Water Reactor (PHWR) as a result of a perturbation caused by one or more of the regulating devices is very important from the operation and maintenance point of view of the reactor. Theoretical design codes available for this purpose take several minutes to calculate the channel power distribution on modern PCs. Artificial Neural networks (ANNs) have been employed in predicting channel power distribution of Indian PHWRs for any given configuration of regulating devices of the reactor. ANNs produce the result much faster and with good accuracy. This paper describes the methodology of ANN, its reliability, the validation range, and scope for its possible on-line use in the actual reactor

Correlation between fuel rack sticking and unintentional re-starting of EDG

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Cheol; Chung, Woo geun; Kang, Seung Hee; Kim, Myeong hoon [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

The Emergency Diesel Generator (EDG) was being tested after overhaul maintenance. While the EDG was running at the rated speed (450 rpm), an operator pressed the manual stop button. But the EDG failed to stop and unintentionally started again. After the unintentional re-start, the EDG maintained running speed of 340 rpm. In the category of a governing system, this paper analyzes the cause of unintentional restart of the EDG that unintentionally re-started and maintained a speed at 340 rpm. The results of the analysis were then verified by a test run. Finally, we identified a correlation between fuel rack sticking and unintentional re-starting of the EDG. An analysis was conducted to confirm the cause of an EDG which was unintentionally restarting and running at 340rpm (rated speed is 450 rpm). Through a test run, it was confirmed that the results of the analysis are correct. The cause of the EDG unintentionally restarting was that it still rotated at 55 rpm over the minimum starting speed at the moment when the shutdown cylinder stopped blocking the fuel, because of a stuck fuel rack at the R7 cylinder. At the same time, the fuel that had been supplied into the cylinders (combustion chamber) by the governing system exploded and the EDG restarted unintentionally.

The Royal Summer Palace, Ferdinand I and Anne

Czech Academy of Sciences Publication Activity Database

Dobalová, Sylva

2015-01-01

Roč. 7, č. 2 (2015), s. 162-175 ISSN 1804-1132 Institutional support: RVO:68378033 Keywords : Anne of Jagiello * Prague Castle * Ferdinand I of Habsburg * olive tree * dynasticism Subject RIV: AL - Art, Architecture, Cultural Heritage

Thermal neutron flux measurements in the rotary specimen rack of the IPR-R1 TRIGA reactor

Energy Technology Data Exchange (ETDEWEB)

Souza, Rose Mary G. do Prado; Rodrigues, Rogério R.; Souza, Luiz Claudio A., E-mail: souzarm@cdtn.br, E-mail: rrr@cdtn.br, E-mail: lcas@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-07-01

The thermal neutron flux in the rotary specimen rack of the IPR-R1 TRIGA reactor at the Nuclear Technology Development Center (CDTN), Belo Horizonte, Brazil, has been measured by the neutron activation method, using bare and cadmium covered gold foils. Those foils were irradiated in the rotary specimen rack with the reactor at 100 kW. The reactor core configuration has 63 fuel elements, composed of 59 original aluminum-clad elements and 4 stainless steel-clad fuel elements. The gamma activities of the foils were measured using Ge spectrometer. The perturbations of the thermal neutron flux caused by the introduction of an absorbing foil into the medium were considered in order to obtain accurate determination of the flux. The thermal neutron flux obtained was 7.4 x 10{sup 11} n.cm{sup -2}.s{sup -1}. (author)

Comparison of ANN and RKS approaches to model SCC strength

Science.gov (United States)

Prakash, Aravind J.; Sathyan, Dhanya; Anand, K. B.; Aravind, N. R.

2018-02-01

Self compacting concrete (SCC) is a high performance concrete that has high flowability and can be used in heavily reinforced concrete members with minimal compaction segregation and bleeding. The mix proportioning of SCC is highly complex and large number of trials are required to get the mix with the desired properties resulting in the wastage of materials and time. The research on SCC has been highly empirical and no theoretical relationships have been developed between the mixture proportioning and engineering properties of SCC. In this work effectiveness of artificial neural network (ANN) and random kitchen sink algorithm(RKS) with regularized least square algorithm(RLS) in predicting the split tensile strength of the SCC is analysed. Random kitchen sink algorithm is used for mapping data to higher dimension and classification of this data is done using Regularized least square algorithm. The training and testing data for the algorithm was obtained experimentally using standard test procedures and materials available. Total of 40 trials were done which were used as the training and testing data. Trials were performed by varying the amount of fine aggregate, coarse aggregate, dosage and type of super plasticizer and water. Prediction accuracy of the ANN and RKS model is checked by comparing the RMSE value of both ANN and RKS. Analysis shows that eventhough the RKS model is good for large data set, its prediction accuracy is as good as conventional prediction method like ANN so the split tensile strength model developed by RKS can be used in industries for the proportioning of SCC with tailor made property.

Ilmus artiklikogumik "Eesti teadlased paguluses" / Anne Valmas

Index Scriptorium Estoniae

Valmas, Anne, 1941-2017

2009-01-01

TLÜ AR väliseesti kirjanduse keskuse ja TTÜ Raamatukogu koostöös 24.03.2009 toimunud konverentsist "Eesti teadlased paguluses", mis tutvustas väliseesti teadlaste osa maailmateaduses. Ettekannete põhjal valminud artiklikogumikust "Eesti teadlased paguluses", koostajad Vahur Mägi ja Anne Valmas. Tallinn : Tallinna Ülikooli Kirjastus, 2009

Perbandingan Metode ANN-PSO Dan ANN-GA Dalam Pemodelan Komposisi Pakan Kambing Peranakan Etawa (PE Untuk Optimasi Kandungan Gizi

Directory of Open Access Journals (Sweden)

Canny Amerilyse Caesar

2016-09-01

Abstract Milk is one of the animal protein sources which it contains all of the substances needed by human body. The main milk producer cattle in Indonesia is dairy cow, however its milk production has not fulfilled the society needs. The alternative is the goat, the Etawa crossbreed (PE. The high quality of milk nutrients content is greatly influenced by some factors one of them, is the food factor. The PE goat livestock division of the UPT Cattle Breeding and the Cattle Food Greenery in Singosari-Malang still faces the problem, it is the low ability in giving the food composition for PE goat. This flaw affects the quality of the produced milk. It needs the artificial science of the milk nutrients contain in order to determine the food composition to produce premium milk with the optimum nutrients contain. The writer uses the method of the Artificial Neural Network (ANN and the Particle Swarm Optimization (PSO to make the modeling of goat food in optimizing the content of goat milk nutrients. In the analysis of the examination that is done with the case of 36 kg goat weight, also the food type used is the 70 % Odot grass and 30% Raja grass can increase the nutrients contain of the protein milk for 0.707% and decrease the fat nutrients contain for 0.879%. If uses the method of Artificial Neural Network (ANN and Genethic Algorithm (GA can increase the nutriens contain of the protein for 0.0852% and decrease the fat nutients contain for 2.3254%.   Key Words : Goat Milk, Optimization, Artificial Neural Network (ANN, Particle Swarm Optimization (PSO, Genetic Algorithm (GA, the food nutrients contain.

Eesti NATO ukselävel / Mari-Ann Kelam

Index Scriptorium Estoniae

Kelam, Mari-Ann, 1946-

2002-01-01

Seda, et NATO liitumisläbirääkimistele kutsutavate seas on ka Eesti, saab veel tänagi pidada üheks meie iseseisva riikluse suursaavutuseks, kui mitte imeks, kirjutab Riigikogu liige Mari-Ann Kelam. Autor: Isamaaliit. Parlamendisaadik

A Sensitive ANN Based Differential Relay for Transformer Protection with Security against CT Saturation and Tap Changer Operation

OpenAIRE

KHORASHADI-ZADEH, Hassan; LI, Zuyi

2014-01-01

This paper presents an artificial neural network (ANN) based scheme for fault identification in power transformer protection. The proposed scheme is featured by the application of ANN to identifying system patterns, the unique choice of harmonics of positive sequence differential currents as ANN inputs, the effective handling of current transformer (CT) saturation with an ANN based approach, and the consideration of tap changer position for correcting secondary CT current. Performanc...

Igal mõisal on oma lugu / Mari-Ann Remmel

Index Scriptorium Estoniae

Remmel, Mari-Ann

2008-01-01

Kirjastuselt "Tänapäev" ilmus raamat "Mõisalegendid. Harjumaa", koostaja Mari-Ann Remmel, kujundaja Angelika Schneider. Kogumik sisaldab ka ajaloolist ning genealoogilist teavet mõisahoonete ning -omanike kohta

KSC technician installs rows of experiment racks in IML-1 spacelab module

Science.gov (United States)

1991-01-01

Kennedy Space Center (KSC) technician installs rows of experiment racks in the International Microgravity Laboratory 1 (IML-1) in the KSC Operations and Checkout (O and C) Bldg. The IML-1 is scheduled to fly on STS-42 in early 1992, and will turn the shuttle into a laboratory dedicated to investigating the effects of microgravity on materials and life processes. View provided by KSC with alternate number KSC-91P-169.

A page is turned with the departure of Anne-Sylvie Catherin

CERN Multimedia

Staff Association

2016-01-01

The Staff Association wants to thank Anne Sylvie Catherin for her achievements during her career at CERN, and in particular during her mandate of head of the Human Resources Department. Anne-Sylvie Catherin arrived at CERN as a lawyer specialized in labor law of International Organizations, and she brought along her knowledge, as well as an unparalleled energy and professionalism. The Staff Association has particularly appreciated her collaborative approach during discussions in the concertation process. This attitude has clearly contributed to the implementation of significant change in the management of human resources, while preserving social peace. We expect that the person who will succeed Anne-Sylvie Catherin will have the same constructive attitude, in respect of the concertation process, as well as a continuity in the definition and implementation of HR processes. Finally, we hope that the new head of HR will be able to develop a long-term vision for the Organization and its staff, measuring to the vi...

Process Control Strategies for Dual-Phase Steel Manufacturing Using ANN and ANFIS

Science.gov (United States)

Vafaeenezhad, H.; Ghanei, S.; Seyedein, S. H.; Beygi, H.; Mazinani, M.

2014-11-01

In this research, a comprehensive soft computational approach is presented for the analysis of the influencing parameters on manufacturing of dual-phase steels. A set of experimental data have been gathered to obtain the initial database used for the training and testing of both artificial neural networks (ANN) and adaptive neuro-fuzzy inference system (ANFIS). The parameters used in the strategy were intercritical annealing temperature, carbon content, and holding time which gives off martensite percentage as an output. A fraction of the data set was chosen to train both ANN and ANFIS, and the rest was put into practice to authenticate the act of the trained networks while seeing unseen data. To compare the obtained results, coefficient of determination and root mean squared error indexes were chosen. Using artificial intelligence methods, it is not necessary to consider and establish a preliminary mathematical model and formulate its affecting parameters on its definition. In conclusion, the martensite percentages corresponding to the manufacturing parameters can be determined prior to a production using these controlling algorithms. Although the results acquired from both ANN and ANFIS are very encouraging, the proposed ANFIS has enhanced performance over the ANN and takes better effect on cost-reduction profit.

Method of assembling spent nuclear fuel storage rack

International Nuclear Information System (INIS)

Igarashi, Ryokichi; Hasegawa, Hidenobu.

1982-01-01

Purpose: To improve the safety of a spent fuel storage rack by stably installing the spent fuel in a pool without using supporting beams. Constitution: A restricted unit is composed of a plurality of spuare cylinders. A plurality of such restricted units are aligned in a direction perpendicularly to the arraying direction of the cylinders in the respective restricted units, are coupled with long connecting plates, and are fixed by welding on a common small base, thereby forming a restricted body. According to such assembling method, a plurality of restricted bodies are connected in a direction that the respective restricted bodies are readily overturned, and are secured to the common base. Accordingly, the restricted bodies can be stably installed in a pool without using supporting beams as the conventional one. (Sekiya, K.)

Anne-Marie Sargueil: ilu on kasulik / intervjueerinud Emilie Toomela

Index Scriptorium Estoniae

Sargueil, Anne-Marie

2015-01-01

Prantsuse Disainiinstituudi juht Anne-Marie Sargueil rääkis prantsuse ja skandinaavia disainist, prantslaste disainieelistustest, uutest suundadest disaini valdkonnas, Eesti Tarbekunsti- ja Disainimuuseumis avatud näitusest "20 prantsuse disainiikooni"

Application of ANN and fuzzy logic algorithms for streamflow ...

Indian Academy of Sciences (India)

1Department of Soil and Water Engineering, College of Technology and Engineering, Maharana Pratap. University of ... It was found that, ANN model performance improved with increasing .... algorithm uses supervised learning that provides.

Ackermann's steering principle behind the optimization of six-bar steering linkages having a rectilinear translating rack and having an infinite to the third number of function-cognates

NARCIS (Netherlands)

Dijksman, E.A.

2000-01-01

Many times a pinion-wheel meshing with a rectilinear moving rack steers the front-wheels of a car having a fixed axis in the rear. The rack then normally translates in its own direction parallel to the fixed line which connects the two fusées. Also the wheelarms, being rigidly attached to the

Novel Formulation of Adaptive MPC as EKF Using ANN Model: Multiproduct Semibatch Polymerization Reactor Case Study.

Science.gov (United States)

Kamesh, Reddi; Rani, Kalipatnapu Yamuna

2017-12-01

In this paper, a novel formulation for nonlinear model predictive control (MPC) has been proposed incorporating the extended Kalman filter (EKF) control concept using a purely data-driven artificial neural network (ANN) model based on measurements for supervisory control. The proposed scheme consists of two modules focusing on online parameter estimation based on past measurements and control estimation over control horizon based on minimizing the deviation of model output predictions from set points along the prediction horizon. An industrial case study for temperature control of a multiproduct semibatch polymerization reactor posed as a challenge problem has been considered as a test bed to apply the proposed ANN-EKFMPC strategy at supervisory level as a cascade control configuration along with proportional integral controller [ANN-EKFMPC with PI (ANN-EKFMPC-PI)]. The proposed approach is formulated incorporating all aspects of MPC including move suppression factor for control effort minimization and constraint-handling capability including terminal constraints. The nominal stability analysis and offset-free tracking capabilities of the proposed controller are proved. Its performance is evaluated by comparison with a standard MPC-based cascade control approach using the same adaptive ANN model. The ANN-EKFMPC-PI control configuration has shown better controller performance in terms of temperature tracking, smoother input profiles, as well as constraint-handling ability compared with the ANN-MPC with PI approach for two products in summer and winter. The proposed scheme is found to be versatile although it is based on a purely data-driven model with online parameter estimation.

Kui vana on kunstnik? / Anneli Porri

Index Scriptorium Estoniae

Porri, Anneli, 1980-

2003-01-01

Rahvusvahelise kunstihariduse konverentsi "InSea on Sea" raames Kunstiakadeemia galeriis Karin Laansoo kureeritud Tallinna Kunstikooli õpilaste tööde näitus "MÄRKmed", Draakoni galeriis Mari Sobolevi kureeritud Viljandi Maagümnaasiumi kunstistuudio näitus "Sisseastumiseksam maailma", rahvusraamatukogus Anneli Porri kureeritud näitus "Kokkuvõte" EKA tänavuste lõpetajate töödest ja näitus "Leitud tagahoovist", Kullo galeriis rahvusvaheline näitus "Dialoog erinevuste vahel"

Video Monitoring and Analysis System for Vivarium Cage Racks | NCI Technology Transfer Center | TTC

Science.gov (United States)

This invention pertains to a system for continuous observation of rodents in home-cage environments with the specific aim to facilitate the quantification of activity levels and behavioral patterns for mice housed in a commercial ventilated cage rack.  The National Cancer Institute’s Radiation Biology Branch seeks partners interested in collaborative research to co-develop a video monitoring system for laboratory animals.

Nanofabricated racks of aligned and anchored DNA substrates for single-molecule imaging.

Science.gov (United States)

Gorman, Jason; Fazio, Teresa; Wang, Feng; Wind, Shalom; Greene, Eric C

2010-01-19

Single-molecule studies of biological macromolecules can benefit from new experimental platforms that facilitate experimental design and data acquisition. Here we develop new strategies to construct curtains of DNA in which the molecules are aligned with respect to one another and maintained in an extended configuration by anchoring both ends of the DNA to the surface of a microfluidic sample chamber that is otherwise coated with an inert lipid bilayer. This "double-tethered" DNA substrate configuration is established through the use of nanofabricated rack patterns comprised of two distinct functional elements: linear barriers to lipid diffusion that align DNA molecules anchored by one end to the bilayer and antibody-coated pentagons that provide immobile anchor points for the opposite ends of the DNA. These devices enable the alignment and anchoring of thousands of individual DNA molecules, which can then be visualized using total internal reflection fluorescence microscopy under conditions that do not require continuous application of buffer flow to stretch the DNA. This unique strategy offers the potential for studying protein-DNA interactions on large DNA substrates without compromising measurements through application of hydrodynamic force. We provide a proof-of-principle demonstration that double-tethered DNA curtains made with nanofabricated rack patterns can be used in a one-dimensional diffusion assay that monitors the motion of quantum dot-tagged proteins along DNA.

Modeling of an Aged Porous Silicon Humidity Sensor Using ANN Technique

Directory of Open Access Journals (Sweden)

Tarikul ISLAM

2006-10-01

Full Text Available Porous silicon (PS sensor based on capacitive technique used for measuring relative humidity has the advantages of low cost, ease of fabrication with controlled structure and CMOS compatibility. But the response of the sensor is nonlinear function of humidity and suffers from errors due to aging and stability. One adaptive linear (ADALINE ANN model has been developed to model the behavior of the sensor with a view to estimate these errors and compensate them. The response of the sensor is represented by third order polynomial basis function whose coefficients are determined by the ANN technique. The drift in sensor output due to aging of PS layer is also modeled by adapting the weights of the polynomial function. ANN based modeling is found to be more suitable than conventional physical modeling of PS humidity sensor in changing environment and drift due to aging. It helps online estimation of nonlinearity as well as monitoring of the fault of the PS humidity sensor using the coefficients of the model.

An upgrade practice of a double-rack source 60Co source irradiator

International Nuclear Information System (INIS)

Dong Hui; Peng Wei; Liu Zhaomin

2009-01-01

An upgrade practice of a double-rack irradiator with the design capacity of 2.96 x10 16 Bq (800 kCi) was reported. The detailed contents and characteristics of this upgrade, a comparison on the facility performance before and after the upgrade, and the cost-benefit analysis were carried out. After upgrade, the facility performance increased over 50%, and brought much directly economical benefit and indirectly economical benefit. The upgrade was successful, and set up a demonstrational sample. (authors)

Impact Analysis for Fuel Assemblies in Spent Fuel Storage Rack

International Nuclear Information System (INIS)

Oh, Jinho

2013-01-01

The design and structural integrity evaluation of a spent fuel storage rack (SFSR) utilized for storing and protecting the spent fuel assemblies generated during the operation of a reactor are very important in terms of nuclear safety and waste management. The objective of this study is to show the validity of the SFSR design as well as fuel assembly through a structural integrity evaluation based on a numerical analysis. In particular, a dynamic time history analysis considering the gaps between the fuel assemblies and the walls of the storage cell pipes in the SFSR was performed to check the structural integrity of the fuel assembly and storage cell pipe

Impact Analysis for Fuel Assemblies in Spent Fuel Storage Rack

Energy Technology Data Exchange (ETDEWEB)

Oh, Jinho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-07-01

The design and structural integrity evaluation of a spent fuel storage rack (SFSR) utilized for storing and protecting the spent fuel assemblies generated during the operation of a reactor are very important in terms of nuclear safety and waste management. The objective of this study is to show the validity of the SFSR design as well as fuel assembly through a structural integrity evaluation based on a numerical analysis. In particular, a dynamic time history analysis considering the gaps between the fuel assemblies and the walls of the storage cell pipes in the SFSR was performed to check the structural integrity of the fuel assembly and storage cell pipe.

Artificial Neural Networks (ANNs for flood forecasting at Dongola Station in the River Nile, Sudan

Directory of Open Access Journals (Sweden)

Sulafa Hag Elsafi

2014-09-01

Full Text Available Heavy seasonal rains cause the River Nile in Sudan to overflow and flood the surroundings areas. The floods destroy houses, crops, roads, and basic infrastructure, resulting in the displacement of people. This study aimed to forecast the River Nile flow at Dongola Station in Sudan using an Artificial Neural Network (ANN as a modeling tool and validated the accuracy of the model against actual flow. The ANN model was formulated to simulate flows at a certain location in the river reach, based on flow at upstream locations. Different procedures were applied to predict flooding by the ANN. Readings from stations along the Blue Nile, White Nile, Main Nile, and River Atbara between 1965 and 2003 were used to predict the likelihood of flooding at Dongola Station. The analysis indicated that the ANN provides a reliable means of detecting the flood hazard in the River Nile.

Steni muinasjutuvõistluse võitjad selgunud / Ants Roos, Ann Roos

Index Scriptorium Estoniae

Roos, Ants

2008-01-01

Steni XVI muinasjutuvõistluse žüriisse kuulusid: Ann Roos, Ants Roos, Leelo Tungal, Krista Kumberg, Leida Olszak, Ülle Väljataga. Tulemused: I koht Siim Niinelaid, II koht Julius Air Kull, III koht Mihkel Rammu. Žürii eriauhinnad: Anna Kristin Peterson, Elis Ruus, Rain Hallikas, Mariliis Peterson, Marjaliisa Palu, Karl Kirsimäe, Margaret Pulk. Ergutusauhinnad: Karmel Klaus, Martti Kaljuste, Kristina Korell, Mirjam Võsaste, Mihkel Põder, Iirys Kalde, Miriam Jamul, Mari-Ann Mägi, Ketlin Saar, Liisbeth Kirss. Muud eriauhinnad said: Allan Läll, Berle Mees, Anett Kuuse, Karl Erik Kübarsepp, Grete Tamm, Siim Niinelaid, Kaisa Marie Sipelgas, Ellen Anett Põldmaa, Evelin Laul, Karl Laas, Karl Stamm, Kerli Retter

Luksuslik ruum kõigile : vestlus arhitekt Anne Lacatoniga = Luxury space for everyone : interview with Anne Lacaton / intervjueerinud Katrin Paadam

Index Scriptorium Estoniae

Lacaton, Anne, 1955-

2013-01-01

Prantsuse arhitekt Anne Lacaton oma büroo (Lacaton & Vassal, Frédéric Druot, 2011) linnaehituslikult uuendusliku projekti järgi ümber ehitatud 1960. aastate korterelamust Tour du Bois-le-Prêtre Pariisis, sotsiaalelamute ehitusest Prantsusmaal, 1960.-1970. aastatel ehitatud elamute taaskasutusega seotud probleemidest, rekonstrueerimise kasulikkusest võrreldes elamu lammutamise ja uuesti ehitamisega, linnas elavatele inimestele paremate elamistingimuste loomisest, linnaplaneerimisest

Using ANN and EPR models to predict carbon monoxide concentrations in urban area of Tabriz

Directory of Open Access Journals (Sweden)

Mohammad Shakerkhatibi

2015-09-01

Full Text Available Background: Forecasting of air pollutants has become a popular topic of environmental research today. For this purpose, the artificial neural network (AAN technique is widely used as a reliable method for forecasting air pollutants in urban areas. On the other hand, the evolutionary polynomial regression (EPR model has recently been used as a forecasting tool in some environmental issues. In this research, we compared the ability of these models to forecast carbon monoxide (CO concentrations in the urban area of Tabriz city. Methods: The dataset of CO concentrations measured at the fixed stations operated by the East Azerbaijan Environmental Office along with meteorological data obtained from the East Azerbaijan Meteorological Bureau from March 2007 to March 2013, were used as input for the ANN and EPR models. Results: Based on the results, the performance of ANN is more reliable in comparison with EPR. Using the ANN model, the correlation coefficient values at all monitoring stations were calculated above 0.85. Conversely, the R2 values for these stations were obtained <0.41 using the EPR model. Conclusion: The EPR model could not overcome the nonlinearities of input data. However, the ANN model displayed more accurate results compared to the EPR. Hence, the ANN models are robust tools for predicting air pollutant concentrations.

Predicting the Deflections of Micromachined Electrostatic Actuators Using Artificial Neural Network (ANN

Directory of Open Access Journals (Sweden)

Hing Wah LEE

2009-03-01

Full Text Available In this study, a general purpose Artificial Neural Network (ANN model based on the feed-forward back-propagation (FFBP algorithm has been used to predict the deflections of a micromachined structures actuated electrostatically under different loadings and geometrical parameters. A limited range of simulation results obtained via CoventorWare™ numerical software will be used initially to train the neural network via back-propagation algorithm. The micromachined structures considered in the analyses are diaphragm, fixed-fixed beams and cantilevers. ANN simulation results are compared with results obtained via CoventorWare™ simulations and existing analytical work for validation purpose. The proposed ANN model accurately predicts the deflections of the micromachined structures with great reduction of simulation efforts, establishing the method superiority. This method can be extended for applications in other sensors particularly for modeling sensors applying electrostatic actuation which are difficult in nature due to the inherent non-linearity of the electro-mechanical coupling response.

Ants Orasest ja Anne Lange monograafiast / Jüri Talvet

Index Scriptorium Estoniae

Talvet, Jüri, 1945-

2005-01-01

Arvustus: Oras, Ants. Luulekool. I, Apoloogia / koostajad Hando Runnel ja Jaak Rähesoo. Tartu : Ilmamaa, 2003 ; Oras, Ants. Luulekool II, Meistriklass. Tartu : Ilmamaa, 2004 ; Lange, Anne. Ants Oras : [kirjandusteadlane, -kriitik ja tõlkija (1900-1982)]. Tartu : Ilmamaa, 2004

Hiina tervendus / kommenteerivad Anne, Julia, Weihong Song, Fagang Ren

Index Scriptorium Estoniae

2013-01-01

Tallinnas Tulika 19 asuvast Bai Lan Hiina massaažisalongist, kus ravitakse kuputeraapia, gua sha kraapimisplaatide, moksa, nõelravi ja punktmassaaži abil. Tui na massaaži ja hiina loodusteraapia protseduure kommenteerivad spetsialistid ning patsiendid Anne ja Julia

Vene ja prantsuse kunsti imetlemisest Londonis / Ann Alari

Index Scriptorium Estoniae

Alari, Ann

2008-01-01

Näitus "Venemaalt pärit prantsuse ja vene shedöövrid" kuningliku kunstiakadeemia saalides Londonis. Vaatluse all oli ajavahemik 1870 kuni 1925. Tööd olid pärit Moskvas elanud tekstiilitöösturitest suurärimeeste Sergei Shtshukini ja Ivan Morozovi kogudest, mis 1917. a. natsionaliseeriti. Kuraator Ann Dumas

ANN-PSO Integrated Optimization Methodology for Intelligent Control of MMC Machining

Science.gov (United States)

Chandrasekaran, Muthumari; Tamang, Santosh

2017-08-01

Metal Matrix Composites (MMC) show improved properties in comparison with non-reinforced alloys and have found increased application in automotive and aerospace industries. The selection of optimum machining parameters to produce components of desired surface roughness is of great concern considering the quality and economy of manufacturing process. In this study, a surface roughness prediction model for turning Al-SiCp MMC is developed using Artificial Neural Network (ANN). Three turning parameters viz., spindle speed ( N), feed rate ( f) and depth of cut ( d) were considered as input neurons and surface roughness was an output neuron. ANN architecture having 3 -5 -1 is found to be optimum and the model predicts with an average percentage error of 7.72 %. Particle Swarm Optimization (PSO) technique is used for optimizing parameters to minimize machining time. The innovative aspect of this work is the development of an integrated ANN-PSO optimization method for intelligent control of MMC machining process applicable to manufacturing industries. The robustness of the method shows its superiority for obtaining optimum cutting parameters satisfying desired surface roughness. The method has better convergent capability with minimum number of iterations.

Prediction of scour below submerged pipeline crossing a river using ANN.

Science.gov (United States)

Azamathulla, H M; Zakaria, Nor Azazi

2011-01-01

The process involved in the local scour below pipelines is so complex that it makes it difficult to establish a general empirical model to provide accurate estimation for scour. This paper describes the use of artificial neural networks (ANN) to estimate the pipeline scour depth. The data sets of laboratory measurements were collected from published works and used to train the network or evolve the program. The developed networks were validated by using the observations that were not involved in training. The performance of ANN was found to be more effective when compared with the results of regression equations in predicting the scour depth around pipelines.

A modeling of dynamic storage assignment for order picking in beverage warehousing with Drive-in Rack system

Science.gov (United States)

Hadi, M. Z.; Djatna, T.; Sugiarto

2018-04-01

This paper develops a dynamic storage assignment model to solve storage assignment problem (SAP) for beverages order picking in a drive-in rack warehousing system to determine the appropriate storage location and space for each beverage products dynamically so that the performance of the system can be improved. This study constructs a graph model to represent drive-in rack storage position then combine association rules mining, class-based storage policies and an arrangement rule algorithm to determine an appropriate storage location and arrangement of the product according to dynamic orders from customers. The performance of the proposed model is measured as rule adjacency accuracy, travel distance (for picking process) and probability a product become expiry using Last Come First Serve (LCFS) queue approach. Finally, the proposed model is implemented through computer simulation and compare the performance for different storage assignment methods as well. The result indicates that the proposed model outperforms other storage assignment methods.

Artificial neural network (ANN) approach for modeling Zn(II) adsorption in batch process

Energy Technology Data Exchange (ETDEWEB)

Yildiz, Sayiter [Engineering Faculty, Cumhuriyet University, Sivas (Turkmenistan)

2017-09-15

Artificial neural networks (ANN) were applied to predict adsorption efficiency of peanut shells for the removal of Zn(II) ions from aqueous solutions. Effects of initial pH, Zn(II) concentrations, temperature, contact duration and adsorbent dosage were determined in batch experiments. The sorption capacities of the sorbents were predicted with the aid of equilibrium and kinetic models. The Zn(II) ions adsorption onto peanut shell was better defined by the pseudo-second-order kinetic model, for both initial pH, and temperature. The highest R{sup 2} value in isotherm studies was obtained from Freundlich isotherm for the inlet concentration and from Temkin isotherm for the sorbent amount. The high R{sup 2} values prove that modeling the adsorption process with ANN is a satisfactory approach. The experimental results and the predicted results by the model with the ANN were found to be highly compatible with each other.

Artificial neural network (ANN) approach for modeling Zn(II) adsorption in batch process

International Nuclear Information System (INIS)

Yildiz, Sayiter

2017-01-01

Artificial neural networks (ANN) were applied to predict adsorption efficiency of peanut shells for the removal of Zn(II) ions from aqueous solutions. Effects of initial pH, Zn(II) concentrations, temperature, contact duration and adsorbent dosage were determined in batch experiments. The sorption capacities of the sorbents were predicted with the aid of equilibrium and kinetic models. The Zn(II) ions adsorption onto peanut shell was better defined by the pseudo-second-order kinetic model, for both initial pH, and temperature. The highest R"2 value in isotherm studies was obtained from Freundlich isotherm for the inlet concentration and from Temkin isotherm for the sorbent amount. The high R"2 values prove that modeling the adsorption process with ANN is a satisfactory approach. The experimental results and the predicted results by the model with the ANN were found to be highly compatible with each other.

Intelligent MRTD testing for thermal imaging system using ANN

Science.gov (United States)

Sun, Junyue; Ma, Dongmei

2006-01-01

The Minimum Resolvable Temperature Difference (MRTD) is the most widely accepted figure for describing the performance of a thermal imaging system. Many models have been proposed to predict it. The MRTD testing is a psychophysical task, for which biases are unavoidable. It requires laboratory conditions such as normal air condition and a constant temperature. It also needs expensive measuring equipments and takes a considerable period of time. Especially when measuring imagers of the same type, the test is time consuming. So an automated and intelligent measurement method should be discussed. This paper adopts the concept of automated MRTD testing using boundary contour system and fuzzy ARTMAP, but uses different methods. It describes an Automated MRTD Testing procedure basing on Back-Propagation Network. Firstly, we use frame grabber to capture the 4-bar target image data. Then according to image gray scale, we segment the image to get 4-bar place and extract feature vector representing the image characteristic and human detection ability. These feature sets, along with known target visibility, are used to train the ANN (Artificial Neural Networks). Actually it is a nonlinear classification (of input dimensions) of the image series using ANN. Our task is to justify if image is resolvable or uncertainty. Then the trained ANN will emulate observer performance in determining MRTD. This method can reduce the uncertainties between observers and long time dependent factors by standardization. This paper will introduce the feature extraction algorithm, demonstrate the feasibility of the whole process and give the accuracy of MRTD measurement.

Q&A: Grace Anne Koppel, Living Well with COPD

Science.gov (United States)

... their own lives back is the most rewarding thing we have ever done. Read More "The Challenge of COPD" Articles Q&A: Grace Anne Koppel, Living Well with COPD / What is COPD? / What Causes COPD? / Getting Tested / Am I at Risk? / COPD Quiz Fall ...

2017-2018 Travel Expense Reports for Mary Anne Chambers ...

International Development Research Centre (IDRC) Digital Library (Canada)

Chantal Taylor

Ottawa. Airfare: $368.41. Other. Transportation: $69.95. Accommodation: $542.79. Meals and. Incidentals: $164.42. Other: $0.00. Total: $1,145.57. Comments: From residence in Thornhill, Ontario. 2017-2018 Travel Expense Reports for Mary. Anne Chambers, Governor, Chairperson of the. Human Resources Committee.

2017-2018 Travel Expense Reports for Mary Anne Chambers ...

International Development Research Centre (IDRC) Digital Library (Canada)

Chantal Taylor

Ottawa. Airfare: $563.72. Other. Transportation: $74.26. Accommodation: $0.00. Meals and. Incidentals: $46.17. Other: $30.00. Total: $714.15. Comments: From residence in Thornhill, Ontario. 2017-2018 Travel Expense Reports for Mary. Anne Chambers, Governor, Chairperson of the. Human Resources Committee.

Professor Anne Khademian named National Academy of Public Administration Fellow

OpenAIRE

Chadwick, Heather Riley

2009-01-01

Anne Khademian, professor with Virginia Tech's Center for Public Administration and Policy, School of Public and International Affairs, at the Alexandria, Va., campus has been elected a National Academy of Public Administration (NAPA) Fellow.

Theory Study and Application of the BP-ANN Method for Power Grid Short-Term Load Forecasting

Institute of Scientific and Technical Information of China (English)

Xia Hua; Gang Zhang; Jiawei Yang; Zhengyuan Li

2015-01-01

Aiming at the low accuracy problem of power system short⁃term load forecasting by traditional methods, a back⁃propagation artifi⁃cial neural network (BP⁃ANN) based method for short⁃term load forecasting is presented in this paper. The forecast points are re⁃lated to prophase adjacent data as well as the periodical long⁃term historical load data. Then the short⁃term load forecasting model of Shanxi Power Grid (China) based on BP⁃ANN method and correlation analysis is established. The simulation model matches well with practical power system load, indicating the BP⁃ANN method is simple and with higher precision and practicality.

La légitimation du rock en URSS dans les années 1970-1980

OpenAIRE

Zaytseva, Anna

2017-01-01

RésuméL'article analyse le chemin parcouru par le rock en URSS puis en Russie, de l'état d'une (sous)culture occidentalisée anglophone, ayant trouvé refuge dans les discothèques des années 1960-1970, jusqu'au canon du russkij rok actuel, devenu presque synonyme de poésie chantée, via sa légitimation progressive dans les années 1980. Celle-ci a été amorcée à la fin des années 1970 avec l’arrivée en force d'une nouvelle génération artistique au sein de l'underground rock (« nouvelle vague » de ...

Evaluation of AMPX-KENO benchmark calculations for high-density spent fuel storage racks

International Nuclear Information System (INIS)

Turner, S.E.; Gurley, M.K.

1981-01-01

The AMPX-KENO computer code package is commonly used to evaluate criticality in high-density spent fuel storage rack designs. Consequently, it is important to know the reliability that can be placed on such calculations and whether or not the results are conservative. This paper evaluates a series of AMPX-KENO calculations which have been made on selected critical experiments. The results are compared with similar analyses reported in the literature by the Oak Ridge National Laboratory and BandW. 8 refs

Vegetarian Eco-feminist Consciousness in Carol Ann Duffy’s Poetry

Directory of Open Access Journals (Sweden)

Jie Zhou

2015-07-01

Full Text Available This paper discusses vegetarian eco-feminist consciousness in Carol Ann Duffy’s poetry by close analysis of two poems, namely “The Dolphins” and “A Healthy Diet” from her poem collection Standing Female Nude. The former is a dramatic monologue of a dolphin, which is exploited by people, and the latter is a dramatic monologue of an omnipotent observer in a restaurant. Both poems criticized the species-ism, and together, they showed the poet’s vegetarian eco-feminist consciousness. A close reading of the two poems from the eco-feminist perspective helps the reader understand why Carol Ann Duffy is honored as the first woman poet laureate in British history, and better understand vegetarian eco-feminism and its influence in British society. Keywords: eco-feminism; consciousness, species-ism, vegetarian, animal, diet

The Rack-Gear Tool Generation Modelling. Non-Analytical Method Developed in CATIA, Using the Relative Generating Trajectories Method

Science.gov (United States)

Teodor, V. G.; Baroiu, N.; Susac, F.; Oancea, N.

2016-11-01

The modelling of a curl of surfaces associated with a pair of rolling centrodes, when it is known the profile of the rack-gear's teeth profile, by direct measuring, as a coordinate matrix, has as goal the determining of the generating quality for an imposed kinematics of the relative motion of tool regarding the blank. In this way, it is possible to determine the generating geometrical error, as a base of the total error. The generation modelling allows highlighting the potential errors of the generating tool, in order to correct its profile, previously to use the tool in machining process. A method developed in CATIA is proposed, based on a new method, namely the method of “relative generating trajectories”. They are presented the analytical foundation, as so as some application for knows models of rack-gear type tools used on Maag teething machines.

Data-Driven Modeling of Complex Systems by means of a Dynamical ANN

Science.gov (United States)

Seleznev, A.; Mukhin, D.; Gavrilov, A.; Loskutov, E.; Feigin, A.

2017-12-01

The data-driven methods for modeling and prognosis of complex dynamical systems become more and more popular in various fields due to growth of high-resolution data. We distinguish the two basic steps in such an approach: (i) determining the phase subspace of the system, or embedding, from available time series and (ii) constructing an evolution operator acting in this reduced subspace. In this work we suggest a novel approach combining these two steps by means of construction of an artificial neural network (ANN) with special topology. The proposed ANN-based model, on the one hand, projects the data onto a low-dimensional manifold, and, on the other hand, models a dynamical system on this manifold. Actually, this is a recurrent multilayer ANN which has internal dynamics and capable of generating time series. Very important point of the proposed methodology is the optimization of the model allowing us to avoid overfitting: we use Bayesian criterion to optimize the ANN structure and estimate both the degree of evolution operator nonlinearity and the complexity of nonlinear manifold which the data are projected on. The proposed modeling technique will be applied to the analysis of high-dimensional dynamical systems: Lorenz'96 model of atmospheric turbulence, producing high-dimensional space-time chaos, and quasi-geostrophic three-layer model of the Earth's atmosphere with the natural orography, describing the dynamics of synoptical vortexes as well as mesoscale blocking systems. The possibility of application of the proposed methodology to analyze real measured data is also discussed. The study was supported by the Russian Science Foundation (grant #16-12-10198).

2016-2017 Travel Expense Reports for Mary Anne Chambers ...

International Development Research Centre (IDRC) Digital Library (Canada)

Beata Bialic

Date(s):. 2016-07-06. Destination(s):. Ottawa. Airfare: $482.11. Other. Transportation: $64.30. Accommodation: $0.00. Meals and. Incidentals: $25.28. Other: $0.00. Total: $571.69. Comments: 2016-2017 Travel Expense Reports for Mary. Anne Chambers, Governor, Chairperson of the. Human Resources Committee.

Mapping brain circuits of reward and motivation: in the footsteps of Ann Kelley.

Science.gov (United States)

Richard, Jocelyn M; Castro, Daniel C; Difeliceantonio, Alexandra G; Robinson, Mike J F; Berridge, Kent C

2013-11-01

Ann Kelley was a scientific pioneer in reward neuroscience. Her many notable discoveries included demonstrations of accumbens/striatal circuitry roles in eating behavior and in food reward, explorations of limbic interactions with hypothalamic regulatory circuits, and additional interactions of motivation circuits with learning functions. Ann Kelley's accomplishments inspired other researchers to follow in her footsteps, including our own laboratory group. Here we describe results from several lines of our research that sprang in part from earlier findings by Kelley and colleagues. We describe hedonic hotspots for generating intense pleasure 'liking', separate identities of 'wanting' versus 'liking' systems, a novel role for dorsal neostriatum in generating motivation to eat, a limbic keyboard mechanism in nucleus accumbens for generating intense desire versus intense dread, and dynamic limbic transformations of learned memories into motivation. We describe how origins for each of these themes can be traced to fundamental contributions by Ann Kelley. Copyright © 2013 Elsevier Ltd. All rights reserved.

Storage rack for holding spent fuel elements from nuclear power plants

International Nuclear Information System (INIS)

Krieger, F.

1978-01-01

In the fuel rack containing a great number of compartments with square cross-sections, the structural elements required by the system are statically designed in such a way, that optimal utilization of space as well as shielding of the compartments with respect to each other is guaranteed. In order to achieve this the compartments may be formed by profiled sheets having got trapezoidal edges taken off. Two sheets, each running parallel with respect to each other, form a double shell. The compartments are formed by another double shell, also consisting of two sheets and lying mirror-inverted with respect to the first shell touching this one. (DG) [de

Anne Sütü ve Mikrobiyota Gelişimi

OpenAIRE

GÜNEY, Rabiye; ÇINAR, Nursan

2017-01-01

Sağlıklı mikrobiyotanın etkisine yönelik yapılan çalışmalarda, çocukların gelecekteki sağlığı için mikrobiyota gelişiminin büyük önem taşıdığı vurgulanmaktadır. Astım, şeker hastalığı, obezite gibi birçok hastalığın zarar görmüş ya da gelişmemiş bağırsak mikrobiyotası ile yakın ilişkisi bulunmaktadır. Anne sütü, sağlıklı bir bağırsak mikrobiyotasının gelişmesi için bebeğe aktarılan çok sayıda non-patojen bakteriyi içinde barındırmaktadır. Bununla birlikte, anne sütündeki mikroorganizmaların n...

Prediction of Tourism Demand in Iran by Using Artificial Neural Network (ANN and Supporting Vector Machine (SVR

Directory of Open Access Journals (Sweden)

Seyedehelham Sadatiseyedmahalleh

2016-02-01

Full Text Available This research examines and proves this effectiveness connected with artificial neural networks (ANNs as an alternative approach to the use of Support Vector Machine (SVR in the tourism research. This method can be used for the tourism industry to define the turism’s demands in Iran. The outcome reveals the use of ANNs in tourism research might result in better quotations when it comes to prediction bias and accuracy. Even more applications of ANNs in the context of tourism demand evaluation is needed to establish and validate the effects.

2016-2017 Travel Expense Reports for Margaret Ann Biggs ...

International Development Research Centre (IDRC) Digital Library (Canada)

Beata Bialic

Purpose: Internal IDRC meetings. Date(s):. 2016-07-04 to 2016-07-06. Destination(s):. Ottawa. Airfare: $0.00. Other. Transportation: $39.00. Accommodation: $0.00. Meals and. Incidentals: $25.43. Other: $0.00. Total: $64.43. Comments: 2016-2017 Travel Expense Reports for. Margaret Ann Biggs, Chairperson.

2016-2017 Travel Expense Reports for Mary Anne Chambers ...

International Development Research Centre (IDRC) Digital Library (Canada)

chantal taylor

Purpose: Board meetings. Date(s):. 2017-03-19 to 2017-03-22. Destination(s):. Ottawa. Airfare: $121.05. Other. Transportation: $51.92. Accommodation: $926.48. Meals and. Incidentals: $190.40. Other: $0.00. Total: $1,289.85. Comments: 2016-2017 Travel Expense Reports for Mary. Anne Chambers, Governor ...

ANN-Benchmarks: A Benchmarking Tool for Approximate Nearest Neighbor Algorithms

DEFF Research Database (Denmark)

Aumüller, Martin; Bernhardsson, Erik; Faithfull, Alexander

2017-01-01

This paper describes ANN-Benchmarks, a tool for evaluating the performance of in-memory approximate nearest neighbor algorithms. It provides a standard interface for measuring the performance and quality achieved by nearest neighbor algorithms on different standard data sets. It supports several...... visualise these as images, Open image in new window plots, and websites with interactive plots. ANN-Benchmarks aims to provide a constantly updated overview of the current state of the art of k-NN algorithms. In the short term, this overview allows users to choose the correct k-NN algorithm and parameters...... for their similarity search task; in the longer term, algorithm designers will be able to use this overview to test and refine automatic parameter tuning. The paper gives an overview of the system, evaluates the results of the benchmark, and points out directions for future work. Interestingly, very different...

A relay rack for a control and protection system for nuclear reactors

International Nuclear Information System (INIS)

Miyata, Yasuyuki; Oda, Noriaki; Akiyama, Toyoshi

1975-01-01

It is obvious that all the equipment in the various systems that constitute a nuclear power plant must exhibit the highest levels of reliability, but the reactor control and protection system is of vital importance, and thus it requires a particularly thorough approach, incorporating redundancy, independence and separation. The paper describes the functions, construction and specifications of the relay rack - one of the most important items of equipment for reactor control and protection in a generating facility using a pressurized-water reactor - and it gives details of the extent to which these three requirements are satisfied. (author)

A Fault Diagnosis Model Based on LCD-SVD-ANN-MIV and VPMCD for Rotating Machinery

Directory of Open Access Journals (Sweden)

Songrong Luo

2016-01-01

Full Text Available The fault diagnosis process is essentially a class discrimination problem. However, traditional class discrimination methods such as SVM and ANN fail to capitalize the interactions among the feature variables. Variable predictive model-based class discrimination (VPMCD can adequately use the interactions. But the feature extraction and selection will greatly affect the accuracy and stability of VPMCD classifier. Aiming at the nonstationary characteristics of vibration signal from rotating machinery with local fault, singular value decomposition (SVD technique based local characteristic-scale decomposition (LCD was developed to extract the feature variables. Subsequently, combining artificial neural net (ANN and mean impact value (MIV, ANN-MIV as a kind of feature selection approach was proposed to select more suitable feature variables as input vector of VPMCD classifier. In the end of this paper, a novel fault diagnosis model based on LCD-SVD-ANN-MIV and VPMCD is proposed and proved by an experimental application for roller bearing fault diagnosis. The results show that the proposed method is effective and noise tolerant. And the comparative results demonstrate that the proposed method is superior to the other methods in diagnosis speed, diagnosis success rate, and diagnosis stability.

Application of ANN and fuzzy logic algorithms for streamflow ...

Indian Academy of Sciences (India)

The present study focusses on development of models using ANN and fuzzy logic (FL) algorithm for predicting the streamflow for catchment of Savitri River Basin. The input vector to these models were daily rainfall, mean daily evaporation, mean daily temperature and lag streamflow used. In the present study, 20 years ...

2016-2017 Travel Expense Reports for Mary Anne Chambers ...

International Development Research Centre (IDRC) Digital Library (Canada)

Beata Bialic

Purpose: Board meetings. Date(s):. 2016-11-20 to 2016-11-23. Destination(s):. Ottawa. Airfare: $445.14. Other. Transportation: $29.05. Accommodation: $786.80. Meals and. Incidentals: $76.79. Other: $0.00. Total: $1,337.78. Comments: 2016-2017 Travel Expense Reports for Mary. Anne Chambers, Governor, Chairperson ...

2016-2017 Travel Expense Reports for Mary Anne Chambers ...

International Development Research Centre (IDRC) Digital Library (Canada)

Beata Bialic

Date(s):. 2016-08-14 to 2016-08-23. Destination(s):. Peru/Colombia. Airfare: $3,484.87. Other. Transportation: $0.00. Accommodation: $1,942.21. Meals and. Incidentals: $395.27. Other: $75.50. Total: $5,897.85. Comments: 2016-2017 Travel Expense Reports for Mary. Anne Chambers, Governor, Chairperson of the.

Aspekte van die outeursfunksie in Antjie Krog se Lady Anne (1989)

OpenAIRE

M. Crous

2002-01-01

Aspects of the author function in Antjie Krog’s Lady Anne (1989) The purpose of this essay is to investigate the Foucauldian notion of the so-called “author function” in Antjie Krog’s seventh volume of poetry, viz. Lady Anne (1989). It is an attempt to show how the notion of the death of the author (Barthes) links up with this theorisation of Foucault. Furthermore, it is also an attempt to indicate the characteristic features of the so-called “author function” in the late eighties in Afr...

Mart ja Mari-Ann Susi taotlevad omanikena Concordia pankrotti / Andri Maimets

Index Scriptorium Estoniae

Maimets, Andri, 1979-

2003-01-01

Concordia Ülikooli rektor Mart Susi esitas kohtule avalduse, milles taotleb ülikooli pidanud Concordia Varahalduse OÜ pankroti väljakuulutamist. Vt. samas: Mari-Ann Susi õigustas ülikooli raha kasutamist

Standard specification for boron-Based neutron absorbing material systems for use in nuclear spent fuel storage racks

CERN Document Server

American Society for Testing and Materials. Philadelphia

2011-01-01

1.1 This specification defines criteria for boron-based neutron absorbing material systems used in racks in a pool environment for storage of nuclear light water reactor (LWR) spent-fuel assemblies or disassembled components to maintain sub-criticality in the storage rack system. 1.2 Boron-based neutron absorbing material systems normally consist of metallic boron or a chemical compound containing boron (for example, boron carbide, B4C) supported by a matrix of aluminum, steel, or other materials. 1.3 In a boron-based absorber, neutron absorption occurs primarily by the boron-10 isotope that is present in natural boron to the extent of 18.3 ± 0.2 % by weight (depending upon the geological origin of the boron). Boron, enriched in boron-10 could also be used. 1.4 The materials systems described herein shall be functional – that is always be capable to maintain a B10 areal density such that subcriticality Keff <0.95 or Keff <0.98 or Keff < 1.0 depending on the design specification for the service...

Materials Science Research Rack Onboard the International Space Station

Science.gov (United States)

Reagan, Shawn; Frazier, Natalie; Lehman, John

2016-01-01

The Materials Science Research Rack (MSRR) is a research facility developed under a cooperative research agreement between NASA and ESA for materials science investigations on the International Space Station (ISS). MSRR was launched on STS-128 in August 2009 and currently resides in the U.S. Destiny Laboratory Module. Since that time, MSRR has logged more than 1400 hours of operating time. The MSRR accommodates advanced investigations in the microgravity environment on the ISS for basic materials science research in areas such as solidification of metals and alloys. The purpose is to advance the scientific understanding of materials processing as affected by microgravity and to gain insight into the physical behavior of materials processing. MSRR allows for the study of a variety of materials, including metals, ceramics, semiconductor crystals, and glasses. Materials science research benefits from the microgravity environment of space, where the researcher can better isolate chemical and thermal properties of materials from the effects of gravity. With this knowledge, reliable predictions can be made about the conditions required on Earth to achieve improved materials. MSRR is a highly automated facility with a modular design capable of supporting multiple types of investigations. The NASA-provided Rack Support Subsystem provides services (power, thermal control, vacuum access, and command and data handling) to the ESA-developed Materials Science Laboratory (MSL) that accommodates interchangeable Furnace Inserts (FI). Two ESA-developed FIs are presently available on the ISS: the Low Gradient Furnace (LGF) and the Solidification and Quenching Furnace (SQF). Sample Cartridge Assemblies (SCAs), each containing one or more material samples, are installed in the FI by the crew and can be processed at temperatures up to 1400?C. ESA continues to develop samples with 14 planned for launch and processing in the near future. Additionally NASA has begun developing SCAs to

Benthic Habitat Mapping - Dry Tortugas RoxAnn Acoustic Sensor Data Points

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — During April 2001 RoxAnn single-beam acoustic surveys were conducted at the North Unit of the Tortugas Ecological Reserve, Florida. Thirteen transects associated...

Development and Application of ANN Model for Worker Assignment into Virtual Cells of Large Sized Configurations

International Nuclear Information System (INIS)

Murali, R. V.; Fathi, Khalid; Puri, A. B.

2010-01-01

This paper presents an extended version of study already undertaken on development of an artificial neural networks (ANNs) model for assigning workforce into virtual cells under virtual cellular manufacturing systems (VCMS) environments. Previously, the same authors have introduced this concept and applied it to virtual cells of two-cell configuration and the results demonstrated that ANNs could be a worth applying tool for carrying out workforce assignments. In this attempt, three-cell configurations problems are considered for worker assignment task. Virtual cells are formed under dual resource constraint (DRC) context in which the number of available workers is less than the total number of machines available. Since worker assignment tasks are quite non-linear and highly dynamic in nature under varying inputs and conditions and, in parallel, ANNs have the ability to model complex relationships between inputs and outputs and find similar patterns effectively, an attempt was earlier made to employ ANNs into the above task. In this paper, the multilayered perceptron with feed forward (MLP-FF) neural network model has been reused for worker assignment tasks of three-cell configurations under DRC context and its performance at different time periods has been analyzed. The previously proposed worker assignment model has been reconfigured and cell formation solutions available for three-cell configuration in the literature are used in combination to generate datasets for training ANNs framework. Finally, results of the study have been presented and discussed.

ANNE TONER. Ellipsis in English Literature: Signs of Omission

DEFF Research Database (Denmark)

Lupton, Tina Jane

2016-01-01

As a freshman, I once met a PhD Student writing about the use of the comma in Jane Austen. For years the thesis topic kept me entertained as an example of how narrowly focused literary study could become. Reading Anne Toner's Ellipsis in English Literature commits me to a recantation of that joke...

NASA/First Materials Science Research Rack (MSRR-1) Module Inserts Development for the International Space Station

Science.gov (United States)

Crouch, Myscha; Carswell, Bill; Farmer, Jeff; Rose, Fred; Tidwell, Paul

1999-01-01

The Material Science Research Rack 1 (MSRR-1) of the Material Science Research Facility (MSRF) contains an Experiment Module (EM) being developed collaboratively by NASA and the European Space Agency (ESA). This NASA/ESA EM will accommodate several different removable and replaceable Module Inserts (MIs) which are installed on orbit. Two of the NASA MIs being developed for specific material science investigations are described herein.

Estimation of Costs and Durations of Construction of Urban Roads Using ANN and SVM

Directory of Open Access Journals (Sweden)

Igor Peško

2017-01-01

Full Text Available Offer preparation has always been a specific part of a building process which has significant impact on company business. Due to the fact that income greatly depends on offer’s precision and the balance between planned costs, both direct and overheads, and wished profit, it is necessary to prepare a precise offer within required time and available resources which are always insufficient. The paper presents a research of precision that can be achieved while using artificial intelligence for estimation of cost and duration in construction projects. Both artificial neural networks (ANNs and support vector machines (SVM are analysed and compared. The best SVM has shown higher precision, when estimating costs, with mean absolute percentage error (MAPE of 7.06% compared to the most precise ANNs which has achieved precision of 25.38%. Estimation of works duration has proved to be more difficult. The best MAPEs were 22.77% and 26.26% for SVM and ANN, respectively.

Smart Rack Monitor for the Linac control system

International Nuclear Information System (INIS)

Shtirbu, S.; Goodwin, R.W.; McCrory, E.S.; Shea, M.F.

1991-01-01

The Smart Rack Monitor (SRM) is a low-cost, one board, data-acquisition module for the upgraded Linac control system at Fermilab. The SRM is based on the Motorola MC68332 microcontroller in the Business Card Computer (BCC) configuration. It is connected to the Linac local control station (to be referred to as Local Station) by an Arcnet LAN, and can be located close to the controlled hardware. Each Local Station is connected to several SRMs. The SRM has 64 A-D channels, sixteen D-A channels, and eight bytes of digital I/O on the mother board. Software Components Group's pSOS is the SRM's kernel. The SRM's software is cross-developed on VAX/VMS in C. The SRM does not have an attached console and is fully controlled by the Local Station. It performs data acquisition and settings, as directed by the Local Station. Its existence is transparent to the rest of the control system. The SRM supports code updates downloading from the VAX, through the Local Station

Why philosophy and history matter : A conversation with Ann Taves

NARCIS (Netherlands)

von Stuckrad, C.K.M.

2010-01-01

The article picks up some ideas that Ann Taves presents in her book Religious Experience Reconsidered, and looks at possible conversations that are not fleshed out in detail in Taves' book. In particular, it is argued that the disciplinary confrontation with philosophy and with historiography is of

Arabidopsis scaffold protein RACK1A modulates rare sugar D-allose regulated gibberellin signaling

OpenAIRE

Fennell, Herman; Olawin, Abdulquadri; Mizanur, Rahman M.; Izumori, Ken; Chen, Jin-Gui; Ullah, Hemayet

2012-01-01

As energy sources and structural components, sugars are the central regulators of plant growth and development. In addition to the abundant natural sugars in plants, more than 50 different kinds of rare sugars exist in nature, several of which show distinct roles in plant growth and development. Recently, one of the rare sugars, D-allose, an epimer of D-glucose at C3, is found to suppress plant hormone gibberellin (GA) signaling in rice. Scaffold protein RACK1A in the model plant Arabidopsis ...

Artificial neural network (ANN)-based prediction of depth filter loading capacity for filter sizing.

Science.gov (United States)

Agarwal, Harshit; Rathore, Anurag S; Hadpe, Sandeep Ramesh; Alva, Solomon J

2016-11-01

This article presents an application of artificial neural network (ANN) modelling towards prediction of depth filter loading capacity for clarification of a monoclonal antibody (mAb) product during commercial manufacturing. The effect of operating parameters on filter loading capacity was evaluated based on the analysis of change in the differential pressure (DP) as a function of time. The proposed ANN model uses inlet stream properties (feed turbidity, feed cell count, feed cell viability), flux, and time to predict the corresponding DP. The ANN contained a single output layer with ten neurons in hidden layer and employed a sigmoidal activation function. This network was trained with 174 training points, 37 validation points, and 37 test points. Further, a pressure cut-off of 1.1 bar was used for sizing the filter area required under each operating condition. The modelling results showed that there was excellent agreement between the predicted and experimental data with a regression coefficient (R 2 ) of 0.98. The developed ANN model was used for performing variable depth filter sizing for different clarification lots. Monte-Carlo simulation was performed to estimate the cost savings by using different filter areas for different clarification lots rather than using the same filter area. A 10% saving in cost of goods was obtained for this operation. © 2016 American Institute of Chemical Engineers Biotechnol. Prog., 32:1436-1443, 2016. © 2016 American Institute of Chemical Engineers.

A computation ANN model for quantifying the global solar radiation: A case study of Al-Aqabah-Jordan

International Nuclear Information System (INIS)

Abolgasem, I M; Alghoul, M A; Ruslan, M H; Chan, H Y; Khrit, N G; Sopian, K

2015-01-01

In this paper, a computation model is developed to predict the global solar radiation (GSR) in Aqaba city based on the data recorded with association of Artificial Neural Networks (ANN). The data used in this work are global solar radiation (GSR), sunshine duration, maximum and minimum air temperature and relative humidity. These data are available from Jordanian meteorological station over a period of two years. The quality of GSR forecasting is compared by using different Learning Algorithms. The decision of changing the ANN architecture is essentially based on the predicted results to obtain the best ANN model for monthly and seasonal GSR. Different configurations patterns were tested using available observed data. It was found that the model using mainly sunshine duration and air temperature as inputs gives accurate results. The ANN model efficiency and the mean square error values show that the prediction model is accurate. It is found that the effect of the three learning algorithms on the accuracy of the prediction model at the training and testing stages for each time scale is mostly within the same accuracy range. (paper)

Measurement and ANN prediction of pH-dependent solubility of nitrogen-heterocyclic compounds.

Science.gov (United States)

Sun, Feifei; Yu, Qingni; Zhu, Jingke; Lei, Lecheng; Li, Zhongjian; Zhang, Xingwang

2015-09-01

Based on the solubility of 25 nitrogen-heterocyclic compounds (NHCs) measured by saturation shake-flask method, artificial neural network (ANN) was employed to the study of the quantitative relationship between the structure and pH-dependent solubility of NHCs. With genetic algorithm-multivariate linear regression (GA-MLR) approach, five out of the 1497 molecular descriptors computed by Dragon software were selected to describe the molecular structures of NHCs. Using the five selected molecular descriptors as well as pH and the partial charge on the nitrogen atom of NHCs (QN) as inputs of ANN, a quantitative structure-property relationship (QSPR) model without using Henderson-Hasselbalch (HH) equation was successfully developed to predict the aqueous solubility of NHCs in different pH water solutions. The prediction model performed well on the 25 model NHCs with an absolute average relative deviation (AARD) of 5.9%, while HH approach gave an AARD of 36.9% for the same model NHCs. It was found that QN played a very important role in the description of NHCs and, with QN, ANN became a potential tool for the prediction of pH-dependent solubility of NHCs. Copyright © 2015 Elsevier Ltd. All rights reserved.

Estimating SPT-N Value Based on Soil Resistivity using Hybrid ANN-PSO Algorithm

Science.gov (United States)

Nur Asmawisham Alel, Mohd; Ruben Anak Upom, Mark; Asnida Abdullah, Rini; Hazreek Zainal Abidin, Mohd

2018-04-01

Standard Penetration Resistance (N value) is used in many empirical geotechnical engineering formulas. Meanwhile, soil resistivity is a measure of soil’s resistance to electrical flow. For a particular site, usually, only a limited N value data are available. In contrast, resistivity data can be obtained extensively. Moreover, previous studies showed evidence of a correlation between N value and resistivity value. Yet, no existing method is able to interpret resistivity data for estimation of N value. Thus, the aim is to develop a method for estimating N-value using resistivity data. This study proposes a hybrid Artificial Neural Network-Particle Swarm Optimization (ANN-PSO) method to estimate N value using resistivity data. Five different ANN-PSO models based on five boreholes were developed and analyzed. The performance metrics used were the coefficient of determination, R2 and mean absolute error, MAE. Analysis of result found that this method can estimate N value (R2 best=0.85 and MAEbest=0.54) given that the constraint, Δ {\\bar{l}}ref, is satisfied. The results suggest that ANN-PSO method can be used to estimate N value with good accuracy.

SU-E-T-206: Improving Radiotherapy Toxicity Based On Artificial Neural Network (ANN) for Head and Neck Cancer Patients

Energy Technology Data Exchange (ETDEWEB)

Cho, Daniel D; Wernicke, A Gabriella; Nori, Dattatreyudu; Chao, KSC; Parashar, Bhupesh; Chang, Jenghwa [Weill Cornell Medical College, NY, NY (United States)

2014-06-01

Purpose/Objective(s): The aim of this study is to build the estimator of toxicity using artificial neural network (ANN) for head and neck cancer patients Materials/Methods: An ANN can combine variables into a predictive model during training and considered all possible correlations of variables. We constructed an ANN based on the data from 73 patients with advanced H and N cancer treated with external beam radiotherapy and/or chemotherapy at our institution. For the toxicity estimator we defined input data including age, sex, site, stage, pathology, status of chemo, technique of external beam radiation therapy (EBRT), length of treatment, dose of EBRT, status of post operation, length of follow-up, the status of local recurrences and distant metastasis. These data were digitized based on the significance and fed to the ANN as input nodes. We used 20 hidden nodes (for the 13 input nodes) to take care of the correlations of input nodes. For training ANN, we divided data into three subsets such as training set, validation set and test set. Finally, we built the estimator for the toxicity from ANN output. Results: We used 13 input variables including the status of local recurrences and distant metastasis and 20 hidden nodes for correlations. 59 patients for training set, 7 patients for validation set and 7 patients for test set and fed the inputs to Matlab neural network fitting tool. We trained the data within 15% of errors of outcome. In the end we have the toxicity estimation with 74% of accuracy. Conclusion: We proved in principle that ANN can be a very useful tool for predicting the RT outcomes for high risk H and N patients. Currently we are improving the results using cross validation.

SU-E-T-206: Improving Radiotherapy Toxicity Based On Artificial Neural Network (ANN) for Head and Neck Cancer Patients

International Nuclear Information System (INIS)

Cho, Daniel D; Wernicke, A Gabriella; Nori, Dattatreyudu; Chao, KSC; Parashar, Bhupesh; Chang, Jenghwa

2014-01-01

Purpose/Objective(s): The aim of this study is to build the estimator of toxicity using artificial neural network (ANN) for head and neck cancer patients Materials/Methods: An ANN can combine variables into a predictive model during training and considered all possible correlations of variables. We constructed an ANN based on the data from 73 patients with advanced H and N cancer treated with external beam radiotherapy and/or chemotherapy at our institution. For the toxicity estimator we defined input data including age, sex, site, stage, pathology, status of chemo, technique of external beam radiation therapy (EBRT), length of treatment, dose of EBRT, status of post operation, length of follow-up, the status of local recurrences and distant metastasis. These data were digitized based on the significance and fed to the ANN as input nodes. We used 20 hidden nodes (for the 13 input nodes) to take care of the correlations of input nodes. For training ANN, we divided data into three subsets such as training set, validation set and test set. Finally, we built the estimator for the toxicity from ANN output. Results: We used 13 input variables including the status of local recurrences and distant metastasis and 20 hidden nodes for correlations. 59 patients for training set, 7 patients for validation set and 7 patients for test set and fed the inputs to Matlab neural network fitting tool. We trained the data within 15% of errors of outcome. In the end we have the toxicity estimation with 74% of accuracy. Conclusion: We proved in principle that ANN can be a very useful tool for predicting the RT outcomes for high risk H and N patients. Currently we are improving the results using cross validation

Assessment of spatial distribution of soil heavy metals using ANN-GA, MSLR and satellite imagery.

Science.gov (United States)

Naderi, Arman; Delavar, Mohammad Amir; Kaboudin, Babak; Askari, Mohammad Sadegh

2017-05-01

This study aims to assess and compare heavy metal distribution models developed using stepwise multiple linear regression (MSLR) and neural network-genetic algorithm model (ANN-GA) based on satellite imagery. The source identification of heavy metals was also explored using local Moran index. Soil samples (n = 300) were collected based on a grid and pH, organic matter, clay, iron oxide contents cadmium (Cd), lead (Pb) and zinc (Zn) concentrations were determined for each sample. Visible/near-infrared reflectance (VNIR) within the electromagnetic ranges of satellite imagery was applied to estimate heavy metal concentrations in the soil using MSLR and ANN-GA models. The models were evaluated and ANN-GA model demonstrated higher accuracy, and the autocorrelation results showed higher significant clusters of heavy metals around the industrial zone. The higher concentration of Cd, Pb and Zn was noted under industrial lands and irrigation farming in comparison to barren and dryland farming. Accumulation of industrial wastes in roads and streams was identified as main sources of pollution, and the concentration of soil heavy metals was reduced by increasing the distance from these sources. In comparison to MLSR, ANN-GA provided a more accurate indirect assessment of heavy metal concentrations in highly polluted soils. The clustering analysis provided reliable information about the spatial distribution of soil heavy metals and their sources.

Wind speed forecasting in three different regions of Mexico, using a hybrid ARIMA-ANN model

Energy Technology Data Exchange (ETDEWEB)

Cadenas, Erasmo [Facultad de Ingenieria Mecanica, Universidad Michoacana de San Nicolas de Hidalgo, Santiago Tapia No. 403, Centro (Mexico); Rivera, Wilfrido [Centro de Ivestigacion en Energia, Universidad Nacional Autonoma de Mexico, Apartado Postal 34, Temixco 62580, Morelos (Mexico)

2010-12-15

In this paper the wind speed forecasting in the Isla de Cedros in Baja California, in the Cerro de la Virgen in Zacatecas and in Holbox in Quintana Roo is presented. The time series utilized are average hourly wind speed data obtained directly from the measurements realized in the different sites during about one month. In order to do wind speed forecasting Hybrid models consisting of Autoregressive Integrated Moving Average (ARIMA) models and Artificial Neural Network (ANN) models were developed. The ARIMA models were first used to do the wind speed forecasting of the time series and then with the obtained errors ANN were built taking into account the nonlinear tendencies that the ARIMA technique could not identify, reducing with this the final errors. Once the Hybrid models were developed 48 data out of sample for each one of the sites were used to do the wind speed forecasting and the results were compared with the ARIMA and the ANN models working separately. Statistical error measures such as the mean error (ME), the mean square error (MSE) and the mean absolute error (MAE) were calculated to compare the three methods. The results showed that the Hybrid models predict the wind velocities with a higher accuracy than the ARIMA and ANN models in the three examined sites. (author)

Enamik Mõtteloo Sihtkapitali rahast kasvab USA aktsiates / Mart Trummal ; interv. Anne Oja

Index Scriptorium Estoniae

Trummal, Mart

2006-01-01

Intervjuu Eesti Mõtteloo Sihtkapitali juhi Mart Trummaliga. Tabel: Mõtteloo Sihtkapitali vara on USA-s noteeritud indeksifondides; Investeeringud Eesti aktsiatesse. Diagramm: Finantsinvesteeringute maht. Vt. samas: Anne Oja. Dividendisaajate esirinnas. Kommenteerib Annika Matson

Artificial Neural Network (ANN) Model to Predict Depression among Geriatric Population at a Slum in Kolkata, India.

Science.gov (United States)

Sau, Arkaprabha; Bhakta, Ishita

2017-05-01

Depression is one of the most important causes of mortality and morbidity among the geriatric population. Although, the aging brain is more vulnerable to depression, it cannot be considered as physiological and an inevitable part of ageing. Various sociodemographic and morbidity factors are responsible for the depression among them. Using Artificial Neural Network (ANN) model depression can be predicted from various sociodemographic variables and co morbid conditions even at community level by the grass root level health care workers. To predict depression among geriatric population from sociodemographic and morbidity attributes using ANN. An observational descriptive study with cross-sectional design was carried out at a slum under the service area of Bagbazar Urban Health and Training Centre (UHTC) in Kolkata. Among 126 elderlies under Bagbazar UHTC, 105 were interviewed using predesigned and pretested schedule. Depression status was assessed using 30 item Geriatric Depression Scale. WEKA 3.8.0 was used to develop the ANN model and test its performance. Prevalence of depression among the study population was 45.7%. Various sociodemographic variables like age, gender, literacy, living spouse, working status, personal income, family type, substance abuse and co morbid conditions like visual problem, mobility problem, hearing problem and sleeping problem were taken into consideration to develop the model. Prediction accuracy of this ANN model was 97.2%. Depression among geriatric population can be predicted accurately using ANN model from sociodemographic and morbidity attributes.

Redesign of the spent fuel storage racks at the Trojan Nuclear Plant

International Nuclear Information System (INIS)

Stump, K.

1987-01-01

The spent fuel pool (SFP) at the Trojan Nuclear Plant located near Prescott, Oregon, was originally designed to hold 1.33 cores worth of spent fuel assemblies. Due to the delay in the site selection and preparation process for the spent fuel repository, the SFP storage capacity was increased in 1978 from 260 assemblies to 651 assemblies and in 1983 was increased again from 651 to 1408 assemblies to allow Trojan to continue operations through the year 2003 with a full core reserve in the SFP. Now it appears unlikely that a high level waste repository will be in operation before 2010. This indicates that a further capacity increase in the SFP is required to allow commercial operation until 2010, at which time the repository should be open to receive spent fuel. To accomplish this, an increase of seven times the original SFP capacity of 260 assemblies is needed. This paper presents a spent fuel assembly rack design that enables the required capacity increase in the SFP to be met. By the use of a boron carbide - silicon polymer inside a titanium/vanadium honeycomb as a neutron absorber between the fuel assemblies and by increasing the metal to water ratio of the spent fuel pool to harden the neutron energy spectrum the capacity of the SFP is increased to 1880 assemblies for an increase of 7.23 times the original spent fuel pool capacity. The multiplication factor for the pool with every fuel assembly slot filled in the new rack system is 0.62; well below the NRC regulatory limit of keff < 0.95. The capacity increase with allow the commercial operation of the Trojan Nuclear Plant through 2010 with a full core reserve in the spent fuel pool

Modelling and automatic reactive power control of isolated wind-diesel hybrid power systems using ANN

International Nuclear Information System (INIS)

Bansal, R.C.

2008-01-01

This paper presents an artificial neural network (ANN) based approach to tune the parameters of the static var compensator (SVC) reactive power controller over a wide range of typical load model parameters. The gains of PI (proportional integral) based SVC are optimised for typical values of the load voltage characteristics (n q ) by conventional techniques. Using the generated data, the method of multi-layer feed forward ANN with error back propagation training is employed to tune the parameters of the SVC. An ANN tuned SVC controller has been applied to control the reactive power of a variable slip/speed isolated wind-diesel hybrid power system. It is observed that the maximum deviations of all parameters are more for larger values of n q . It has been shown that initially synchronous generator supplies the reactive power required by the induction generator and/or load, and the latter reactive power is purely supplied by the SVC

Modelling and automatic reactive power control of isolated wind-diesel hybrid power systems using ANN

Energy Technology Data Exchange (ETDEWEB)

Bansal, R.C. [Electrical and Electronics Engineering Division, School of Engineering and Physics, The University of the South Pacific, Suva (Fiji)

2008-02-15

This paper presents an artificial neural network (ANN) based approach to tune the parameters of the static var compensator (SVC) reactive power controller over a wide range of typical load model parameters. The gains of PI (proportional integral) based SVC are optimised for typical values of the load voltage characteristics (n{sub q}) by conventional techniques. Using the generated data, the method of multi-layer feed forward ANN with error back propagation training is employed to tune the parameters of the SVC. An ANN tuned SVC controller has been applied to control the reactive power of a variable slip/speed isolated wind-diesel hybrid power system. It is observed that the maximum deviations of all parameters are more for larger values of n{sub q}. It has been shown that initially synchronous generator supplies the reactive power required by the induction generator and/or load, and the latter reactive power is purely supplied by the SVC. (author)

Application of ann-based decision making pattern recognition to fishing operations

Energy Technology Data Exchange (ETDEWEB)

Akhlaghinia, M.; Torabi, F.; Wilton, R.R. [University of Regina, Saskatchewan (Canada). Faculty of Engineering. Dept. of Petroleum Engineering], e-mail: Farshid.Torabi@uregina.ca

2010-10-15

Decision making is a crucial part of fishing operations. Proper decisions should be made to prevent wasted time and associated costs on unsuccessful operations. This paper presents a novel model to help drilling managers decide when to commence and when to quit a fishing operation. A decision making model based on Artificial Neural Network (ANN) has been developed that utilizes Pattern Recognition based on 181 fishing incidents from one of the most fish-prone fields of the southwest of Iran. All parameters chosen to train the ANN-Based Pattern Recognition Tool are assumed to play a role in the success of the fishing operation and are therefore used to decide whether a fishing operation should be performed or not. If the tool deems the operation suitable for consideration, a cost analysis of the fishing operation can then be performed to justify its overall cost. (author)

Sexuality and gender in contemporary women's Gothic fiction - Angela Carter's and Anne Rice's Vampires: Angela Carter's and Anne Rice's Vampires

OpenAIRE

Fernanda Sousa Carvalho

2009-01-01

xxx In this thesis, I provide an analysis of Angela Carter's and Anne Rice's works based on their depiction of vampires. My corpus is composed by Carter's short stories 'The Loves of Lady Purple' and 'The Lady of the House of Love' and by Rice's novels The Vampire Lestat and The Queen of the Damned. My analysis of this corpus is based on four approaches: a comparison between Carter's and Rice's works, supported by their common use of vampire characters; an investigation of how this use con...

Thesis defence: Anneli Baran Possibilities for studying semantics in phraseology / Outi Lauhakangas

Index Scriptorium Estoniae

Lauhakangas, Outi

2011-01-01

15. märtsil 2011 kaitses Anneli Baran Tartu Ülikooli kultuuriteaduste ja kunstide instituudis doktoriväitekirja Fraseologismide semantika uurimisvõimalused, juhendaja Arvo Krikmann (Eesti Kirjandusmuuseum), oponent dr Outi Lauhakangas (Soome Kirjanduse Selts)

Prediction of Ryznar Stability Index for Treated Water of WTPs Located on Al-Karakh Side of Baghdad City using Artificial Neural Network (ANN Technique

Directory of Open Access Journals (Sweden)

Awatif Soaded Alsaqqar

2016-06-01

Full Text Available In this research an Artificial Neural Network (ANN technique was applied for the prediction of Ryznar Index (RI of the flowing water from WTPs in Al-Karakh side (left side in Baghdad city for year 2013. Three models (ANN1, ANN2 and ANN3 have been developed and tested using data from Baghdad Mayoralty (Amanat Baghdad including drinking water quality for the period 2004 to 2013. The results indicate that it is quite possible to use an artificial neural networks in predicting the stability index (RI with a good degree of accuracy. Where ANN 2 model could be used to predict RI for the effluents from Al-Karakh, Al-Qadisiya and Al-Karama WTPs as the highest correlation coefficient were obtained 92.4, 82.9 and 79.1% respectively. For Al-Dora WTP, ANN 3 model could be used as R was 92.8%.

Identification of Constitutive Parameters Using Inverse Strategy Coupled to an ANN Model

International Nuclear Information System (INIS)

Aguir, H.; Chamekh, A.; BelHadjSalah, H.; Hambli, R.

2007-01-01

This paper deals with the identification of material parameters using an inverse strategy. In the classical methods, the inverse technique is generally coupled with a finite element code which leads to a long computing time. In this work an inverse strategy coupled with an ANN procedure is proposed. This method has the advantage of being faster than the classical one. To validate this approach an experimental plane tensile and bulge tests are used in order to identify material behavior. The ANN model is trained from finite element simulations of the two tests. In order to reduce the gap between the experimental responses and the numerical ones, the proposed method is coupled with an optimization procedure to identify material parameters for the AISI304. The identified material parameters are the hardening curve and the anisotropic coefficients

Les premières années de The Himalayan Journal (1929-1940

Directory of Open Access Journals (Sweden)

Michel Raspaud

2001-05-01

Full Text Available IntroductionLa création de The Himalayan Club, sur le territoire de l’Empire des Indes à la fin de l’année 1927, s’accompagne presque aussitôt de la publication de The Himalayan Journal, en février 1929, soit mois de dix-huit mois après la création officielle de l’institution. L’objet du présent texte concerne donc la vie de The Himalayan Club lors de ses premières années d’existence, depuis la date de sa création jusqu’au début de la seconde guerre mondiale. Cependant, l’intérêt se focaliser...

Practitioner Profile: An Interview with Anne Brennan Malec, Ph.D.

Directory of Open Access Journals (Sweden)

Anne Brennan Malec

2015-12-01

Full Text Available Dr. Anne Brennan Malec is the founder and managing partner of Symmetry Counseling, a counseling, coaching, and psychotherapy group practice located in downtown Chicago. She has been the driving force behind Symmetry Counseling’s success – what started in 2011 with six offices and five counselors now houses over 25 clinicians.

Thermal Evaluation of Storage Rack with an Advanced Neutron Absorber during Normal Operation

Energy Technology Data Exchange (ETDEWEB)

Lee, Hee-Jae; Kim, Mi-Jin; Sohn, Dong-Seong [UNIST, Ulsan (Korea, Republic of)

2016-10-15

The storage capacity of the domestic wet storage site is expected to reach saturation from Hanbit in 2024 to Sin-wolseong in 2038 and accordingly management alternatives are urgently taken. Since installation of the dense rack is considered in the short term, it is necessary to urgently develop an advanced neutron absorber which can be applied to a spent nuclear fuel storage facility. Neutron absorber is the material for controlling the reactivity. A material which has excellent thermal neutron absorption ability, high strength and corrosion resistance must be selected as the neutron absorber. Existing neutron absorbers are made of boron which has a good thermal absorption ability such as BORAL and METAMIC. However, possible problems have been reported in using the boron-based neutron absorber for wet storage facility. Gadolinium is known to have higher neutron absorption cross-section than that of boron. And the strength of duplex stainless steel is about 1.5 times higher than stainless steel 304 which has been frequently used as a structural material. Therefore, duplex stainless steel which contains gadolinium is in consideration as an advanced neutron absorber. Temperature distribution is shown in figure 4. In pool bottom region near the inlet shows a relatively low tendency and heat generated from the fuel assemblies is transmitted to the pool upper region by the vertical flow. Also, temperature gradient appear in rack structures for the axial direction and temperature is uniformly distributed in the pool upper region. Table 1 presents the calculated results. The maximum temperature is 306.63K and does not exceed the 333.15K (60℃). The maximum temperature of the neutron absorber is 306.48K.

Doktoritööd : [2007, Anne Lange jt.

Index Scriptorium Estoniae

2007-01-01

20. veebr. kaitseb Anne Lange doktoritööd "The poetics of translation of Ants Oras". 19. jaan. kaitses Tuuli Oder doktoritööd "The model of contemporary professional foreign language teacher". 16. jaan. kaitses Tiit Maran doktoritööd "Conservation biology of the European mink, Mustela lutreola (Linnaeus 1761): decline and causes of extinction". 12. jaan. kaitses Maris Saagpakk doktoritööd "Deutschbaltische Autobiographien als Dokumente des Zeit- und Selbstempfindens: vom Ende des 19. Jh. bis zur Umsiedlung 1939"

ANN based Performance Evaluation of BDI for Condition Monitoring of Induction Motor Bearings

Science.gov (United States)

Patel, Raj Kumar; Giri, V. K.

2017-06-01

One of the critical parts in rotating machines is bearings and most of the failure arises from the defective bearings. Bearing failure leads to failure of a machine and the unpredicted productivity loss in the performance. Therefore, bearing fault detection and prognosis is an integral part of the preventive maintenance procedures. In this paper vibration signal for four conditions of a deep groove ball bearing; normal (N), inner race defect (IRD), ball defect (BD) and outer race defect (ORD) were acquired from a customized bearing test rig, under four different conditions and three different fault sizes. Two approaches have been opted for statistical feature extraction from the vibration signal. In the first approach, raw signal is used for statistical feature extraction and in the second approach statistical features extracted are based on bearing damage index (BDI). The proposed BDI technique uses wavelet packet node energy coefficients analysis method. Both the features are used as inputs to an ANN classifier to evaluate its performance. A comparison of ANN performance is made based on raw vibration data and data chosen by using BDI. The ANN performance has been found to be fairly higher when BDI based signals were used as inputs to the classifier.

Spatial Rack Drives Pitch Configurations: Essence and Content

Science.gov (United States)

Abadjieva, Emilia; Abadjiev, Valentin; Naganawa, Akihiro

2018-03-01

The practical realization of all types of mechanical motions converters is preceded by solving the task of their kinematic synthesis. In this way, the determination of the optimal values of the constant geometrical parameters of the chosen structure of the created mechanical system is achieved. The searched result is a guarantee of the preliminary defined kinematic characteristics of the synthesized transmission and in the first place, to guarantee the law of motions transformation. The kinematic synthesis of mechanical transmissions is based on adequate mathematical modelling of the process of motions transformation and on the object, realizing this transformation. Basic primitives of the mathematical models for synthesis upon a pitch contact point are geometric and kinematic pitch configurations. Their dimensions and mutual position in space are the input parameters for the processes of design and elaboration of the synthesized mechanical device. The study presented here is a brief review of the theory of pitch configurations. It is an independent scientific branch of the spatial gearing theory (theory of hyperboloid gears). On this basis, the essence and content of the corresponding primitives, applicable to the synthesis of spatial rack drives, are defined.

Effectiveness of ANN for seismic behaviour prediction considering geometric configuration effect in concrete gravity dams

Directory of Open Access Journals (Sweden)

Mohd. Saqib

2016-09-01

Full Text Available In this study, an Artificial Neural Networks (ANN model is built and verified for quick estimation of the structural parameter obtained for a concrete gravity dam section due to seismic excitation. The database of numerous inputs and outputs obtained through Abaqus which are further converted into dimensionless forms in the statistical software (MATLAB to build the ANN model. The developed model can be used for accurate estimation of this parameter. The results showed an excellent capability of the model to predict the outputs with high accuracy and reduced computational time.

WEPP and ANN models for simulating soil loss and runoff in a semi-arid Mediterranean region.

Science.gov (United States)

Albaradeyia, Issa; Hani, Azzedine; Shahrour, Isam

2011-09-01

This paper presents the use of both the Water Erosion Prediction Project (WEPP) and the artificial neural network (ANN) for the prediction of runoff and soil loss in the central highland mountainous of the Palestinian territories. Analyses show that the soil erosion is highly dependent on both the rainfall depth and the rainfall event duration rather than on the rainfall intensity as mostly mentioned in the literature. The results obtained from the WEPP model for the soil loss and runoff disagree with the field data. The WEPP underestimates both the runoff and soil loss. Analyses conducted with the ANN agree well with the observation. In addition, the global network models developed using the data of all the land use type show a relatively unbiased estimation for both runoff and soil loss. The study showed that the ANN model could be used as a management tool for predicting runoff and soil loss.

An ANN-based approach to predict blast-induced ground vibration of Gol-E-Gohar iron ore mine, Iran

Directory of Open Access Journals (Sweden)

Mahdi Saadat

2014-02-01

Full Text Available Blast-induced ground vibration is one of the inevitable outcomes of blasting in mining projects and may cause substantial damage to rock mass as well as nearby structures and human beings. In this paper, an attempt has been made to present an application of artificial neural network (ANN to predict the blast-induced ground vibration of the Gol-E-Gohar (GEG iron mine, Iran. A four-layer feed-forward back propagation multi-layer perceptron (MLP was used and trained with Levenberg–Marquardt algorithm. To construct ANN models, the maximum charge per delay, distance from blasting face to monitoring point, stemming and hole depth were taken as inputs, whereas peak particle velocity (PPV was considered as an output parameter. A database consisting of 69 data sets recorded at strategic and vulnerable locations of GEG iron mine was used to train and test the generalization capability of ANN models. Coefficient of determination (R2 and mean square error (MSE were chosen as the indicators of the performance of the networks. A network with architecture 4-11-5-1 and R2 of 0.957 and MSE of 0.000722 was found to be optimum. To demonstrate the supremacy of ANN approach, the same 69 data sets were used for the prediction of PPV with four common empirical models as well as multiple linear regression (MLR analysis. The results revealed that the proposed ANN approach performs better than empirical and MLR models.

Symbolism--The Main Artistic Style of Katherine Anne Porter's Short Stories

Science.gov (United States)

Wang, Ru

2010-01-01

The paper takes Katherine Anne Porter's two short stories: "Flowering Judas", "The Grave" as objects of study. It will try to analyze Porter's writing style through her imaginary conception, vivid psychological description and multiple symbolisms so that we can understand her studies and her attitudes to female psychological…

Kriminalinė pasaka: žanrų suliejimas istorijos atpirkimui Jayne Anne Phillips romane „Quiet Dell“

OpenAIRE

Milvidaitė, Salomėja

2016-01-01

Fairy Tale True Crime: Genre Bending for the Redemption of History in Jayne Anne Phillips' “Quiet Dell” Jayne Anne Phillips’ novel Quiet Dell (2013) depicts a true story concerning the infamous murders in the eponymous hamlet near Phillips’ hometown in West Virginia. The true crime story, however, is given a twist when the first ghostly appearance takes place. The purpose of the present BA paper is to analyse how, by employing various fantastic elements, the genres of true crime and fairy tal...

"I am the vampire for these times": Representations of Postmodernity in Anne Rice's The Vampire Chronicles

OpenAIRE

RINNE, ANTTI

2013-01-01

Anne Ricen The Vampire Chronicles -kirjasarjaa voidaan pitää vampyyrinarratiivien uutena aaltona 1970-luvulta lähtien. Ricen romaaneissa vampyyrit itse nousivat pääosaan kirjojen päähenkilöinä, ja romaanit tietyssä määrin irtautuivat vanhemman vampyyrikirjallisuuden kaavoista. Tutkimukseni aiheena ovat Anne Ricen romaanisarjan kolme ensimmäistä teosta, Interview with the Vampire (1976), The Vampire Lestat (1985) ja The Queen of the Damned (1988). Tutkielmani keskittyy siihen, kuinka kyseiset ...

Application of back-propagation artificial neural network (ANN) to predict crystallite size and band gap energy of ZnO quantum dots

Science.gov (United States)

Pelicano, Christian Mark; Rapadas, Nick; Cagatan, Gerard; Magdaluyo, Eduardo

2017-12-01

Herein, the crystallite size and band gap energy of zinc oxide (ZnO) quantum dots were predicted using artificial neural network (ANN). Three input factors including reagent ratio, growth time, and growth temperature were examined with respect to crystallite size and band gap energy as response factors. The generated results from neural network model were then compared with the experimental results. Experimental crystallite size and band gap energy of ZnO quantum dots were measured from TEM images and absorbance spectra, respectively. The Levenberg-Marquardt (LM) algorithm was used as the learning algorithm for the ANN model. The performance of the ANN model was then assessed through mean square error (MSE) and regression values. Based on the results, the ANN modelling results are in good agreement with the experimental data.

Method of making a rack for the storage of spent nuclear fuel

International Nuclear Information System (INIS)

Machado, O.J.; Moore, J.T.; Cooney, B.F.

1990-01-01

This paper discusses a method of making a rack for storing nuclear fuel. It comprises bending each of the sheets into a sheet structure of configuration of angular transverse cross section, positioning each sheet structure with its longitudinal edges abutting the longitudinal edges of another of the sheet structures, metallurgically joining the abutting edges of the pair of sheet structures whose edges are abutting to form bodies of transverse rectangular cross section, mounting the bodies on a baseplate adjacent to each other with each longitudinal corner of each body face-to-face with a longitudinal corner of each adjacent body, metallurgically joining directly each corner of the each body to each facing corner of each adjacent body, and metallurgically joining each the body to the baseplate

Applying a supervised ANN (artificial neural network) approach to the prognostication of driven wheel energy efficiency indices

International Nuclear Information System (INIS)

Taghavifar, Hamid; Mardani, Aref

2014-01-01

This paper examines the prediction of energy efficiency indices of driven wheels (i.e. traction coefficient and tractive power efficiency) as affected by wheel load, slippage and forward velocity at three different levels with three replicates to form a total of 162 data points. The pertinent experiments were carried out in the soil bin testing facility. A feed-forward ANN (artificial neural network) with standard BP (back propagation) algorithm was practiced to construct a supervised representation to predict the energy efficiency indices of driven wheels. It was deduced, in view of the statistical performance criteria (i.e. MSE (mean squared error) and R 2 ), that a supervised ANN with 3-8-10-2 topology and Levenberg–Marquardt training algorithm represented the optimal model. Modeling implementations indicated that ANN is a powerful technique to prognosticate the stochastic energy efficiency indices as affected by soil-wheel interactions with MSE of 0.001194 and R 2 of 0.987 and 0.9772 for traction coefficient and tractive power efficiency. It was found that traction coefficient and tractive power efficiency increase with increased slippage. A similar trend is valid for the influence of wheel load on the objective parameters. Wherein increase of velocity led to an increment of tractive power efficiency, velocity had no significant effect on traction coefficient. - Highlights: • Energy efficiency indexes were assessed as affected by tire parameters. • ANN was applied for prognostication of the objective parameters. • A 3-8-10-2 ANN with MSE of 0.001194 and R 2 of 0.987 and 0.9772 was designated as optimal model. • Optimal values of learning rate and momentum were found 0.9 and 0.5, respectively

Jo Ann Baumgartner and Sam Earnshaw: Organizers and Farmers

OpenAIRE

Rabkin, Sarah

2010-01-01

Jo Ann Baumgartner directs the Wild Farm Alliance, based in Watsonville, California. WFA’s mission, as described on the organization’s website, is “to promote agriculture that helps to protect and restore wild Nature.” Through research, publications, presentations, events, policy work, and consulting, the organization works to “connect food systems with ecosystems.” Sam Earnshaw is Central Coast regional coordinator of the Community Alliance with Family Farmers. Working with CAFF’s f...

Exploring QSARs of the interaction of flavonoids with GABA (A) receptor using MLR, ANN and SVM techniques.

Science.gov (United States)

Deeb, Omar; Shaik, Basheerulla; Agrawal, Vijay K

2014-10-01

Quantitative Structure-Activity Relationship (QSAR) models for binding affinity constants (log Ki) of 78 flavonoid ligands towards the benzodiazepine site of GABA (A) receptor complex were calculated using the machine learning methods: artificial neural network (ANN) and support vector machine (SVM) techniques. The models obtained were compared with those obtained using multiple linear regression (MLR) analysis. The descriptor selection and model building were performed with 10-fold cross-validation using the training data set. The SVM and MLR coefficient of determination values are 0.944 and 0.879, respectively, for the training set and are higher than those of ANN models. Though the SVM model shows improvement of training set fitting, the ANN model was superior to SVM and MLR in predicting the test set. Randomization test is employed to check the suitability of the models.

Mart ja Mari-Ann Susi taotlevad omanikena Concordia pankrotti / Andri Maimets

Index Scriptorium Estoniae

Maimets, Andri

2003-01-01

Concordia Ülikooli rektori kohast loobunud Mart Susi ning prorektori ametikohalt lahkunud Mari-Ann Susi taotlevad neile kuuluvat ülikooli pidanud miljonivõlgades firma pankrotti. Hiljuti loodi õppejõududest, tudengitest js töötajatest mittetulundusühing Concordia Akadeemiline Ühisus (CAU), selle nõukogu esimees on Hagi Šein

On-line dynamic monitoring automotive exhausts: using BP-ANN for distinguishing multi-components

Science.gov (United States)

Zhao, Yudi; Wei, Ruyi; Liu, Xuebin

2017-10-01

Remote sensing-Fourier Transform infrared spectroscopy (RS-FTIR) is one of the most important technologies in atmospheric pollutant monitoring. It is very appropriate for on-line dynamic remote sensing monitoring of air pollutants, especially for the automotive exhausts. However, their absorption spectra are often seriously overlapped in the atmospheric infrared window bands, i.e. MWIR (3 5μm). Artificial Neural Network (ANN) is an algorithm based on the theory of the biological neural network, which simplifies the partial differential equation with complex construction. For its preferable performance in nonlinear mapping and fitting, in this paper we utilize Back Propagation-Artificial Neural Network (BP-ANN) to quantitatively analyze the concentrations of four typical industrial automotive exhausts, including CO, NO, NO2 and SO2. We extracted the original data of these automotive exhausts from the HITRAN database, most of which virtually overlapped, and established a mixed multi-component simulation environment. Based on Beer-Lambert Law, concentrations can be retrieved from the absorbance of spectra. Parameters including learning rate, momentum factor, the number of hidden nodes and iterations were obtained when the BP network was trained with 80 groups of input data. By improving these parameters, the network can be optimized to produce necessarily higher precision for the retrieved concentrations. This BP-ANN method proves to be an effective and promising algorithm on dealing with multi-components analysis of automotive exhausts.

Numerical weather prediction (NWP) and hybrid ARMA/ANN model to predict global radiation

International Nuclear Information System (INIS)

Voyant, Cyril; Muselli, Marc; Paoli, Christophe; Nivet, Marie-Laure

2012-01-01

We propose in this paper an original technique to predict global radiation using a hybrid ARMA/ANN model and data issued from a numerical weather prediction model (NWP). We particularly look at the multi-layer perceptron (MLP). After optimizing our architecture with NWP and endogenous data previously made stationary and using an innovative pre-input layer selection method, we combined it to an ARMA model from a rule based on the analysis of hourly data series. This model has been used to forecast the hourly global radiation for five places in Mediterranean area. Our technique outperforms classical models for all the places. The nRMSE for our hybrid model MLP/ARMA is 14.9% compared to 26.2% for the naïve persistence predictor. Note that in the standalone ANN case the nRMSE is 18.4%. Finally, in order to discuss the reliability of the forecaster outputs, a complementary study concerning the confidence interval of each prediction is proposed. -- Highlights: ► Time series forecasting with hybrid method based on the use of ALADIN numerical weather model, ANN and ARMA. ► Innovative pre-input layer selection method. ► Combination of optimized MLP and ARMA model obtained from a rule based on the analysis of hourly data series. ► Stationarity process (method and control) for the global radiation time series.

The role of the RACK1 ortholog Cpc2p in modulating pheromone-induced cell cycle arrest in fission yeast.

Directory of Open Access Journals (Sweden)

Magdalena Mos

Full Text Available The detection and amplification of extracellular signals requires the involvement of multiple protein components. In mammalian cells the receptor of activated C kinase (RACK1 is an important scaffolding protein for signal transduction networks. Further, it also performs a critical function in regulating the cell cycle by modulating the G1/S transition. Many eukaryotic cells express RACK1 orthologs, with one example being Cpc2p in the fission yeast Schizosaccharomyces pombe. In contrast to RACK1, Cpc2p has been described to positively regulate, at the ribosomal level, cells entry into M phase. In addition, Cpc2p controls the stress response pathways through an interaction with Msa2p, and sexual development by modulating Ran1p/Pat1p. Here we describe investigations into the role, which Cpc2p performs in controlling the G protein-mediated mating response pathway. Despite structural similarity to Gβ-like subunits, Cpc2p appears not to function at the G protein level. However, upon pheromone stimulation, cells overexpressing Cpc2p display substantial cell morphology defects, disorientation of septum formation and a significantly protracted G1 arrest. Cpc2p has the potential to function at multiple positions within the pheromone response pathway. We provide a mechanistic interpretation of this novel data by linking Cpc2p function, during the mating response, with its previous described interactions with Ran1p/Pat1p. We suggest that overexpressing Cpc2p prolongs the stimulated state of pheromone-induced cells by increasing ste11 gene expression. These data indicate that Cpc2p regulates the pheromone-induced cell cycle arrest in fission yeast by delaying cells entry into S phase.

Modelling the spectral irradiance distribution in sunny inland locations using an ANN-based methodology

International Nuclear Information System (INIS)

Torres-Ramírez, M.; Elizondo, D.; García-Domingo, B.; Nofuentes, G.; Talavera, D.L.

2015-01-01

This work is aimed at verifying that in sunny inland locations artificial intelligence techniques may provide an estimation of the spectral irradiance with adequate accuracy for photovoltaic applications. An ANN (artificial neural network) based method was developed, trained and tested to model the spectral distributions between wavelengths ranging from 350 to 1050 nm. Only commonly available input data such as geographical information regarding location, specific date and time together with horizontal global irradiance and ambient temperature are required. Historical information from a 24-month experimental campaign carried out in Jaén (Spain) provided the necessary data to train and test the ANN tool. A Kohonen self-organized map was used as innovative technique to classify the whole input dataset and build a small and representative training dataset. The shape of the spectral irradiance distribution, the in-plane global irradiance (G T ) and irradiation (H T ) and the APE (average photon energy) values obtained through the ANN method were statistically compared to the experimental ones. In terms of shape distribution fitting, the mean relative deformation error stays below 4.81%. The root mean square percentage error is around 6.89% and 0.45% when estimating G T and APE, respectively. Regarding H T , errors lie below 3.18% in all cases. - Highlights: • ANN-based model to estimate the spectral irradiance distribution in sunny inland locations. • MRDE value stay below 4.81% in spectral irradiance distribution shape fitting. • RMSPE is about 6.89% for the in-plane global irradiance and 0.45% for the average photon energy. • Errors stay below 3.18% for all the months of the year in incident irradiation terms. • Improvement of assessment of the impact of the solar spectrum in the performance of a PV module

Development of ANN-based models to predict the static response and dynamic response of a heat exchanger in a real MVAC system

International Nuclear Information System (INIS)

Hu Qinhua; So, Albert T P; Tse, W L; Ren, Qingchang

2005-01-01

This paper presents a systematic approach to develop artificial neural network (ANN) models to predict the performance of a heat exchanger operating in real mechanical ventilation and air-conditioning (MVAC) system. Two approaches were attempted and presented. Every detailed components of the MVAC system have been considered and we attempt to model each of them by one ANN. This study used the neural network technique to obtain a static and a dynamic model for a heat exchanger mounted in an air handler unit (AHU), which is the key component of the MVAC system. It has been verified that almost all of the predicted values of the ANN model were within 95% - 105% of the measured values, with a consistent mean relative error (MRE) smaller than 2.5%. The paper details our experiences in using ANNs, especially those with back-propagation (BP) structures. Also, the weights and biases of our trained-up ANN models are listed out, which serve as good reference for readers to deal with their own situations

Alice-Anne Martin (1926 - 2016)

CERN Multimedia

2016-01-01

Alice-Anne Martin, known as “Schu” from her maiden name Schubert, passed away on 8 January 2016.   (Image: Gérard Bertin) Hired the year CERN was founded, 1954, when the construction of the Laboratory had not even begun, Schu first worked at the Villa de Cointrin (a historic building now within the grounds of Geneva airport) as a secretary. In this role, she typed the convention between CERN and the Swiss Confederation, prepared by Stéphanie Tixier, as well as some of the "Yellow Reports" that have marked key points in the Laboratory’s history. For example, using a special typewriter with two keyboards – Latin and Greek – she typed the Yellow Report on the KAM theorem by Rolf Hagedorn. Schu also worked with Felix Bloch, the first Director-General of CERN, and later became the secretary of Herbert Coblenz, the first CERN librarian. She was head of the team that edited the proceedings of the ...

The Sally-Anne Test: An Interactional Analysis of a Dyadic Assessment

Science.gov (United States)

Korkiakangas, Terhi; Dindar, Katja; Laitila, Aarno; Kärnä, Eija

2016-01-01

Background: The Sally-Anne test has been extensively used to examine children's theory of mind understanding. Many task-related factors have been suggested to impact children's performance on this test. Yet little is known about the interactional aspects of such dyadic assessment situations that might contribute to the ways in which children…

2006 Maryland Department of Natural Resources Lidar: Caroline, Kent and Queen Anne Counties

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Maryland Department of Natural Resources requested the collection of LIDAR data over Kent, Queen Anne and Caroline Counties, MD. In response, EarthData acquired the...

Predicting PM10 concentration in Seoul metropolitan subway stations using artificial neural network (ANN).

Science.gov (United States)

Park, Sechan; Kim, Minjeong; Kim, Minhae; Namgung, Hyeong-Gyu; Kim, Ki-Tae; Cho, Kyung Hwa; Kwon, Soon-Bark

2018-01-05

The indoor air quality of subway systems can significantly affect the health of passengers since these systems are widely used for short-distance transit in metropolitan urban areas in many countries. The particles generated by abrasion during subway operations and the vehicle-emitted pollutants flowing in from the street in particular affect the air quality in underground subway stations. Thus the continuous monitoring of particulate matter (PM) in underground station is important to evaluate the exposure level of PM to passengers. However, it is difficult to obtain indoor PM data because the measurement systems are expensive and difficult to install and operate for significant periods of time in spaces crowded with people. In this study, we predicted the indoor PM concentration using the information of outdoor PM, the number of subway trains running, and information on ventilation operation by the artificial neural network (ANN) model. As well, we investigated the relationship between ANN's performance and the depth of underground subway station. ANN model showed a high correlation between the predicted and actual measured values and it was able to predict 67∼80% of PM at 6 subway station. In addition, we found that platform shape and depth influenced the model performance. Copyright © 2017 Elsevier B.V. All rights reserved.

78 FR 65380 - Notice of Inventory Completion: University of Michigan, Ann Arbor, MI

Science.gov (United States)

2013-10-31

... the University of Michigan, Ann Arbor, MI. The human remains were removed from Alpena, Isabella, Grand... removed from the Devil River Mound site (20AL1) in Alpena County, MI. A resident of Ossineke, MI...

Prediction of temperature and HAZ in thermal-based processes with Gaussian heat source by a hybrid GA-ANN model

Science.gov (United States)

Fazli Shahri, Hamid Reza; Mahdavinejad, Ramezanali

2018-02-01

Thermal-based processes with Gaussian heat source often produce excessive temperature which can impose thermally-affected layers in specimens. Therefore, the temperature distribution and Heat Affected Zone (HAZ) of materials are two critical factors which are influenced by different process parameters. Measurement of the HAZ thickness and temperature distribution within the processes are not only difficult but also expensive. This research aims at finding a valuable knowledge on these factors by prediction of the process through a novel combinatory model. In this study, an integrated Artificial Neural Network (ANN) and genetic algorithm (GA) was used to predict the HAZ and temperature distribution of the specimens. To end this, a series of full factorial design of experiments were conducted by applying a Gaussian heat flux on Ti-6Al-4 V at first, then the temperature of the specimen was measured by Infrared thermography. The HAZ width of each sample was investigated through measuring the microhardness. Secondly, the experimental data was used to create a GA-ANN model. The efficiency of GA in design and optimization of the architecture of ANN was investigated. The GA was used to determine the optimal number of neurons in hidden layer, learning rate and momentum coefficient of both output and hidden layers of ANN. Finally, the reliability of models was assessed according to the experimental results and statistical indicators. The results demonstrated that the combinatory model predicted the HAZ and temperature more effective than a trial-and-error ANN model.

A call for water-efficient technologies (an interview with dr. Anne Elings)

NARCIS (Netherlands)

Elings, A.

2012-01-01

During the recent International Flower Trade Expo in Nairobi, Wageningen UR Greenhouse Horticulture project leader and greenhouse horticulture specialist Anne Elings pointed out that Kenya is not a water scarce country but management of the same is wanting. HortiNews had a chat with him.

Comparing SVM and ANN based Machine Learning Methods for Species Identification of Food Contaminating Beetles.

Science.gov (United States)

Bisgin, Halil; Bera, Tanmay; Ding, Hongjian; Semey, Howard G; Wu, Leihong; Liu, Zhichao; Barnes, Amy E; Langley, Darryl A; Pava-Ripoll, Monica; Vyas, Himansu J; Tong, Weida; Xu, Joshua

2018-04-25

Insect pests, such as pantry beetles, are often associated with food contaminations and public health risks. Machine learning has the potential to provide a more accurate and efficient solution in detecting their presence in food products, which is currently done manually. In our previous research, we demonstrated such feasibility where Artificial Neural Network (ANN) based pattern recognition techniques could be implemented for species identification in the context of food safety. In this study, we present a Support Vector Machine (SVM) model which improved the average accuracy up to 85%. Contrary to this, the ANN method yielded ~80% accuracy after extensive parameter optimization. Both methods showed excellent genus level identification, but SVM showed slightly better accuracy  for most species. Highly accurate species level identification remains a challenge, especially in distinguishing between species from the same genus which may require improvements in both imaging and machine learning techniques. In summary, our work does illustrate a new SVM based technique and provides a good comparison with the ANN model in our context. We believe such insights will pave better way forward for the application of machine learning towards species identification and food safety.

Dispersion compensation of fiber optic communication system with direct detection using artificial neural networks (ANNs)

Science.gov (United States)

Maghrabi, Mahmoud M. T.; Kumar, Shiva; Bakr, Mohamed H.

2018-02-01

This work introduces a powerful digital nonlinear feed-forward equalizer (NFFE), exploiting multilayer artificial neural network (ANN). It mitigates impairments of optical communication systems arising due to the nonlinearity introduced by direct photo-detection. In a direct detection system, the detection process is nonlinear due to the fact that the photo-current is proportional to the absolute square of the electric field intensity. The proposed equalizer provides the most efficient computational cost with high equalization performance. Its performance is comparable to the benchmark compensation performance achieved by maximum-likelihood sequence estimator. The equalizer trains an ANN to act as a nonlinear filter whose impulse response removes the intersymbol interference (ISI) distortions of the optical channel. Owing to the proposed extensive training of the equalizer, it achieves the ultimate performance limit of any feed-forward equalizer (FFE). The performance and efficiency of the equalizer is investigated by applying it to various practical short-reach fiber optic communication system scenarios. These scenarios are extracted from practical metro/media access networks and data center applications. The obtained results show that the ANN-NFFE compensates for the received BER degradation and significantly increases the tolerance to the chromatic dispersion distortion.

A comparative study of ANN and neuro-fuzzy for the prediction of ...

Indian Academy of Sciences (India)

Istanbul Technical University, Faculty of Civil Engineering, Hydraulics and Water. Resources Division, Maslak 34469, Istanbul, Turkey. Singh et al (2005) examined the potential of the ANN and neuro-fuzzy systems application for the prediction of dynamic constant of rockmass. However, the model proposed by them has ...

ANN Surface Roughness Optimization of AZ61 Magnesium Alloy Finish Turning: Minimum Machining Times at Prime Machining Costs

Directory of Open Access Journals (Sweden)

Adel Taha Abbas

2018-05-01

Full Text Available Magnesium alloys are widely used in aerospace vehicles and modern cars, due to their rapid machinability at high cutting speeds. A novel Edgeworth–Pareto optimization of an artificial neural network (ANN is presented in this paper for surface roughness (Ra prediction of one component in computer numerical control (CNC turning over minimal machining time (Tm and at prime machining costs (C. An ANN is built in the Matlab programming environment, based on a 4-12-3 multi-layer perceptron (MLP, to predict Ra, Tm, and C, in relation to cutting speed, vc, depth of cut, ap, and feed per revolution, fr. For the first time, a profile of an AZ61 alloy workpiece after finish turning is constructed using an ANN for the range of experimental values vc, ap, and fr. The global minimum length of a three-dimensional estimation vector was defined with the following coordinates: Ra = 0.087 μm, Tm = 0.358 min/cm3, C = $8.2973. Likewise, the corresponding finish-turning parameters were also estimated: cutting speed vc = 250 m/min, cutting depth ap = 1.0 mm, and feed per revolution fr = 0.08 mm/rev. The ANN model achieved a reliable prediction accuracy of ±1.35% for surface roughness.

Development of a new software tool, based on ANN technology, in neutron spectrometry and dosimetry research

International Nuclear Information System (INIS)

Ortiz R, J.M.; Martinez B, M.R.; Vega C, H.R.

2007-01-01

Artificial Intelligence is a branch of study which enhances the capability of computers by giving them human-like intelligence. The brain architecture has been extensively studied and attempts have been made to emulate it as in the Artificial Neural Network technology. A large variety of neural network architectures have been developed and they have gained wide-spread popularity over the last few decades. Their application is considered as a substitute for many classical techniques that have been used for many years, as in the case of neutron spectrometry and dosimetry research areas. In previous works, a new approach called Robust Design of Artificial Neural network was applied to build an ANN topology capable to solve the neutron spectrometry and dosimetry problems within the Mat lab programming environment. In this work, the knowledge stored at Mat lab ANN's synaptic weights was extracted in order to develop for first time a customized software application based on ANN technology, which is proposed to be used in the neutron spectrometry and simultaneous dosimetry fields. (Author)

Development of a new software tool, based on ANN technology, in neutron spectrometry and dosimetry research

Energy Technology Data Exchange (ETDEWEB)

Ortiz R, J.M.; Martinez B, M.R.; Vega C, H.R. [Universidad Autonoma de Zacatecas, Av. Ramon Lopez Velarde 801, A.P. 336, 98000 Zacatecas (Mexico)

2007-07-01

Artificial Intelligence is a branch of study which enhances the capability of computers by giving them human-like intelligence. The brain architecture has been extensively studied and attempts have been made to emulate it as in the Artificial Neural Network technology. A large variety of neural network architectures have been developed and they have gained wide-spread popularity over the last few decades. Their application is considered as a substitute for many classical techniques that have been used for many years, as in the case of neutron spectrometry and dosimetry research areas. In previous works, a new approach called Robust Design of Artificial Neural network was applied to build an ANN topology capable to solve the neutron spectrometry and dosimetry problems within the Mat lab programming environment. In this work, the knowledge stored at Mat lab ANN's synaptic weights was extracted in order to develop for first time a customized software application based on ANN technology, which is proposed to be used in the neutron spectrometry and simultaneous dosimetry fields. (Author)

Comparative study of landslides susceptibility mapping methods: Multi-Criteria Decision Making (MCDM) and Artificial Neural Network (ANN)

Science.gov (United States)

Salleh, S. A.; Rahman, A. S. A. Abd; Othman, A. N.; Mohd, W. M. N. Wan

2018-02-01

As different approach produces different results, it is crucial to determine the methods that are accurate in order to perform analysis towards the event. This research aim is to compare the Rank Reciprocal (MCDM) and Artificial Neural Network (ANN) analysis techniques in determining susceptible zones of landslide hazard. The study is based on data obtained from various sources such as local authority; Dewan Bandaraya Kuala Lumpur (DBKL), Jabatan Kerja Raya (JKR) and other agencies. The data were analysed and processed using Arc GIS. The results were compared by quantifying the risk ranking and area differential. It was also compared with the zonation map classified by DBKL. The results suggested that ANN method gives better accuracy compared to MCDM with 18.18% higher accuracy assessment of the MCDM approach. This indicated that ANN provides more reliable results and it is probably due to its ability to learn from the environment thus portraying realistic and accurate result.

Les crises soudanaises des années 80

OpenAIRE

Ahmed, Medani M.; al-Shazali, Salah al-Din; al-Shazali, Salah al-Din; al-Shazali, Salah al-Din; al-Shazali, Salah al-Din; Al-Tom, Abdulahi Osman; Babiker, Mustafa; Babiker, Mustafa; Blin, Louis; Conte, Édouard; Elmekki, Abdelgalil M.; Gore, Paul W.; Hamid, Mohammed Beshir; Ireton, François; Jacquemond, Richard

2008-01-01

Ce dossier est constitué, dans sa quasi-totalité, de contributions de chercheurs et universitaires soudanais proposant une analyse de certains des problèmes cruciaux que leur pays a connus depuis le début des années 80. Les articles qui le composent correspondent aux communications qui devaient initialement être présentées lors d’un colloque portant sur le même thème, prévu à Paris pour décembre 1991 et qui n'a pu avoir lieu du fait de l’impossibilité où se trouvaient certains de ses particip...

Ann modeling of kerf transfer in Co2 laser cutting and optimization of cutting parameters using monte carlo method

Directory of Open Access Journals (Sweden)

Miloš Madić

2015-01-01

Full Text Available In this paper, an attempt has been made to develop a mathematical model in order to study the relationship between laser cutting parameters such as laser power, cutting speed, assist gas pressure and focus position, and kerf taper angle obtained in CO2 laser cutting of AISI 304 stainless steel. To this aim, a single hidden layer artificial neural network (ANN trained with gradient descent with momentum algorithm was used. To obtain an experimental database for the ANN training, laser cutting experiment was planned as per Taguchi’s L27 orthogonal array with three levels for each of the cutting parameters. Statistically assessed as adequate, ANN model was then used to investigate the effect of the laser cutting parameters on the kerf taper angle by generating 2D and 3D plots. It was observed that the kerf taper angle was highly sensitive to the selected laser cutting parameters, as well as their interactions. In addition to modeling, by applying the Monte Carlo method on the developed kerf taper angle ANN model, the near optimal laser cutting parameter settings, which minimize kerf taper angle, were determined.

A vitamini ve anne çocuk sağlığı Derleme

OpenAIRE

Günlemez, Ayla; Atasay, Begüm; Arsan, Saadet

2014-01-01

A vitamini normal görmede hücre farklılaşmasında çoğalmasında ve epitelial bütünlüğün sağlanmasında kritik rol oynar Gelişmekte olan ülkelerde A vitamini eksikliği önemli ve önlenebilir halk sağlığı sorunlarından biridir Bu makalede dünyada ve Türkiye’de A vitamini eksikliği ve anne çocuk sağlığı üzerine etkileri tartışılmaktadır Anahtar Kelimeler: A vitamini anne sağlığı çocuk sağlığıSummaryVitamin A has a critical role in normal vision cell differantiation proliferation and maintanence of e...

Prediction by Artificial Neural Networks (ANN of the diffusivity, mass, moisture, volume and solids on osmotically dehydrated yacon (Smallantus sonchifolius

Directory of Open Access Journals (Sweden)

Julio Rojas Naccha

2012-09-01

Full Text Available The predictive ability of Artificial Neural Network (ANN on the effect of the concentration (30, 40, 50 y 60 % w/w and temperature (30, 40 y 50°C of fructooligosaccharides solution, in the mass, moisture, volume and solids of osmodehydrated yacon cubes, and in the coefficients of the water means effective diffusivity with and without shrinkage was evaluated. The Feedforward type ANN with the Backpropagation training algorithms and the Levenberg-Marquardt weight adjustment was applied, using the following topology: 10-5 goal error, 0.01 learning rate, 0.5 moment coefficient, 2 input neurons, 6 output neurons, one hidden layer with 18 neurons, 15 training stages and logsig-pureline transfer functions. The overall average error achieved by the ANN was 3.44% and correlation coefficients were bigger than 0.9. No significant differences were found between the experimental values and the predicted values achieved by the ANN and with the predicted values achieved by a statistical model of second-order polynomial regression (p > 0.95.

Artificial Neural Network (ANN) design for Hg-Se interactions and their effect on reduction of Hg uptake by radish plant

International Nuclear Information System (INIS)

Kumar Rohit Raj; Abhishek Kardam; Shalini Srivastava; Jyoti Kumar Arora

2010-01-01

The tendency of selenium to interact with heavy metals in presence of naturally occurring species has been exploited for the development of green bioremediation of toxic metals from soil using Artificial Neural Network (ANN) modeling. The cross validation of the data for the reduction in uptake of Hg(II) ions in the plant R. sativus grown in soil and sand culture in presence of selenium has been used for ANN modeling. ANN model based on the combination of back propagation and principal component analysis was able to predict the reduction in Hg uptake with a sigmoid axon transfer function. The data of fifty laboratory experimental sets were used for structuring single layer ANN model. Series of experiments resulted into the performance evaluation based on considering 20% data for testing and 20% data for cross validation at 1,500 Epoch with 0.70 momentums The Levenberg-Marquardt algorithm (LMA) was found as the best of BP algorithms with a minimum mean squared error at the eighth place of the decimal for training (MSE) and cross validation. (author)

Ann Modeling for Grey Particles Produced from Interactions of Different Projectiles with Emulsion Nuclei at 4.5 AGEV/C

International Nuclear Information System (INIS)

El-Bakry, M.N.Y.; Basha, A.M.; Rashed, N.; Mahmoud, M.A.; Radi, A.

2008-01-01

Artificial Neural Network (ANN) is one of the important tools in high energy physics. In this paper, we are using ANN for modeling the multiplicity distributions of grey particles produced from interactions of P, 3 He, 4 He, 6 Li, 12 C, 24 Mg, and 32 S with emulsion nuclei, light nuclei (CNO), and heavy nuclei (Ag Br). The equations of these distributions were obtained

Rimbaud’s influence on Jayne Anne Phillips: from Sweethearts to Shelter

Directory of Open Access Journals (Sweden)

Stéphanie Durrans

2012-06-01

Full Text Available Arthur Rimbaud emerges from Jayne Anne Phillips���s essays as a continual source of fascination. This paper explores the patterns of convergence that unite these two writers one century apart while aiming to provide a deeper and more meaningful appreciation of Phillips’ accomplishments in Shelter. It focuses on Rimbaud’s and Phillips’ conception of language and their emphasis on "visionary writing", before investigating the significance of such patterns on Shelter and exploring the stylistic affinities linking their respective works. In the end, linguistic deconstruction and regeneration appears as one of the ways in which both writers seek to express the hidden traumas of a society in the grips of violence.A en juger par les quelques essais de Jayne Anne Phillips dans lesquels il est mentionné, Arthur Rimbaud semble avoir exercé une véritable fascination sur la jeune nouvelliste et romancière américaine au moins jusque dans les années 1990. Cet article explore la filiation littéraire entre deux auteurs mus par un même souci de renouveler la langue par l’élaboration d’une « écriture visionnaire », à rebours des cadres normatifs et de toute pensée logique. A ce titre, le roman Shelter (1994 apparaît comme l’hommage le plus appuyé rendu par Phillips au poète français, notamment par le double processus de déconstruction et de régénération linguistique qui permet à son auteur d’exprimer les traumatismes individuels et collectifs d’une société hantée par la violence.

BP-ANN for fitting the temperature-germination model and its application in predicting sowing time and region for Bermudagrass.

Directory of Open Access Journals (Sweden)

Erxu Pi

Full Text Available Temperature is one of the most significant environmental factors that affects germination of grass seeds. Reliable prediction of the optimal temperature for seed germination is crucial for determining the suitable regions and favorable sowing timing for turf grass cultivation. In this study, a back-propagation-artificial-neural-network-aided dual quintic equation (BP-ANN-QE model was developed to improve the prediction of the optimal temperature for seed germination. This BP-ANN-QE model was used to determine optimal sowing times and suitable regions for three Cynodon dactylon cultivars (C. dactylon, 'Savannah' and 'Princess VII'. Prediction of the optimal temperature for these seeds was based on comprehensive germination tests using 36 day/night (high/low temperature regimes (both ranging from 5/5 to 40/40°C with 5°C increments. Seed germination data from these temperature regimes were used to construct temperature-germination correlation models for estimating germination percentage with confidence intervals. Our tests revealed that the optimal high/low temperature regimes required for all the three bermudagrass cultivars are 30/5, 30/10, 35/5, 35/10, 35/15, 35/20, 40/15 and 40/20°C; constant temperatures ranging from 5 to 40°C inhibited the germination of all three cultivars. While comparing different simulating methods, including DQEM, Bisquare ANN-QE, and BP-ANN-QE in establishing temperature based germination percentage rules, we found that the R(2 values of germination prediction function could be significantly improved from about 0.6940-0.8177 (DQEM approach to 0.9439-0.9813 (BP-ANN-QE. These results indicated that our BP-ANN-QE model has better performance than the rests of the compared models. Furthermore, data of the national temperature grids generated from monthly-average temperature for 25 years were fit into these functions and we were able to map the germination percentage of these C. dactylon cultivars in the national scale

Damage level prediction of non-reshaped berm breakwater using ANN, SVM and ANFIS models

Digital Repository Service at National Institute of Oceanography (India)

Mandal, S.; SubbaRao; Harish, N.; Lokesha

Marine Structures Laboratory, Department of Applied Mechanics and Hydraulics, NITK, Surathkal, India. Soft computing techniques like Artificial Neural Network (ANN), Support Vector Machine (SVM) and Adaptive Neuro Fuzzy Inference system (ANFIS) models...

Prediction of Frequency for Simulation of Asphalt Mix Fatigue Tests Using MARS and ANN

Directory of Open Access Journals (Sweden)

Ali Reza Ghanizadeh

2014-01-01

Full Text Available Fatigue life of asphalt mixes in laboratory tests is commonly determined by applying a sinusoidal or haversine waveform with specific frequency. The pavement structure and loading conditions affect the shape and the frequency of tensile response pulses at the bottom of asphalt layer. This paper introduces two methods for predicting the loading frequency in laboratory asphalt fatigue tests for better simulation of field conditions. Five thousand (5000 four-layered pavement sections were analyzed and stress and strain response pulses in both longitudinal and transverse directions was determined. After fitting the haversine function to the response pulses by the concept of equal-energy pulse, the effective length of the response pulses were determined. Two methods including Multivariate Adaptive Regression Splines (MARS and Artificial Neural Network (ANN methods were then employed to predict the effective length (i.e., frequency of tensile stress and strain pulses in longitudinal and transverse directions based on haversine waveform. It is indicated that, under controlled stress and strain modes, both methods (MARS and ANN are capable of predicting the frequency of loading in HMA fatigue tests with very good accuracy. The accuracy of ANN method is, however, more than MARS method. It is furthermore shown that the results of the present study can be generalized to sinusoidal waveform by a simple equation.

Transient stability enhancement of wind farms connected to a multi-machine power system by using an adaptive ANN-controlled SMES

International Nuclear Information System (INIS)

Muyeen, S.M.; Hasanien, Hany M.; Al-Durra, Ahmed

2014-01-01

Highlights: • We present an ANN-controlled SMES in this paper. • The objective is to enhance transient stability of WF connected to power system. • The control strategy depends on a PWM VSC and DC–DC converter. • The effectiveness of proposed controller is compared with PI controller. • The validity of the proposed system is verified by simulation results. - Abstract: This paper presents a novel adaptive artificial neural network (ANN)-controlled superconducting magnetic energy storage (SMES) system to enhance the transient stability of wind farms connected to a multi-machine power system during network disturbances. The control strategy of SMES depends mainly on a sinusoidal pulse width modulation (PWM) voltage source converter (VSC) and an adaptive ANN-controlled DC–DC converter using insulated gate bipolar transistors (IGBTs). The effectiveness of the proposed adaptive ANN-controlled SMES is then compared with that of proportional-integral (PI)-controlled SMES optimized by response surface methodology and genetic algorithm (RSM–GA) considering both of symmetrical and unsymmetrical faults. For realistic responses, real wind speed data and two-mass drive train model of wind turbine generator system is considered in the analyses. The validity of the proposed system is verified by the simulation results which are performed using the laboratory standard dynamic power system simulator PSCAD/EMTDC. Notably, the proposed adaptive ANN-controlled SMES enhances the transient stability of wind farms connected to a multi-machine power system

Ann O'Mara, PhD, RN, MPH | Division of Cancer Prevention

Science.gov (United States)

Dr. Ann O'Mara is Head of Palliative Research in the NCI Division of Cancer Prevention. She manages a portfolio of symptom management and palliative and end-of-life care research projects. The majority of these projects focus on the more common morbidities associated with cancer and its treatment, e.g., pain, chemotherapy induced neuropathy, fatigue, sleep disturbances, and

Rapport de frais de 2017-2018 pour Mary Anne Chambers | CRDI ...

International Development Research Centre (IDRC) Digital Library (Canada)

Rapport de frais de 2017-2018 pour Mary Anne Chambers. Total des frais de déplacement : CAD$17,362.55. Réunion du Conseil des gouverneurs. 19 novembre 2017 au 24 novembre 2017. CAD$2,185.41. Réunions au CRDI 1 novembre 2017 CAD$714.15. Constatation de l'impact de la recherche en Afrique de l'Est.

Anne Applebaum: Kas NATO lõpp on lähedal? / Indrek Veiserik

Index Scriptorium Estoniae

Veiserik, Indrek

2009-01-01

USA ajakirjaniku Anne Applebaumi kriitikast NATO kui organisatsiooni toimimise ja Afganistani missiooni suhtes. Kesknädala arvates võiks president Toomas Hendrik Ilves, kes on annetanud A. Applebaumile Maarjamaa Risti III klassi teenetemärgi, kuulata tema välispoliitilisi seisukohti. Viidatakse ka Kanada kindrali Rick Hillieri kriitikale NATO kohta

Inverse problems using ANN in long range atmospheric dispersion with signature analysis picked scattered numerical sensors from CFD

International Nuclear Information System (INIS)

Sharma, Pavan K.; Gera, B.; Ghosh, A.K.; Kushwaha, H.S.

2010-01-01

Scalar dispersion in the atmosphere is an important area wherein different approaches are followed in development of good analytical model. The analyses based on Computational Fluid Dynamics (CFD) codes offer an opportunity of model development based on first principles of physics and hence such models have an edge over the existing models. Both forward and backward calculation methods are being developed for atmospheric dispersion around NPPs at BARC Forward modeling methods, which describe the atmospheric transport from sources to receptors, use forward-running transport and dispersion models or computational fluid dynamics models which are run many times, and the resulting dispersion field is compared to observations from multiple sensors. Backward or inverse modeling methods use only one model run in the reverse direction from the receptors to estimate the upwind sources. Inverse modeling methods include adjoint and tangent linear models, Kalman filters, and variational data assimilation, and neural network. The present paper is aimed at developing a new approach where the identified specific signatures at receptor points form the basis for source estimation or inversions. This approach is expected to reduce the large transient data sets to reduced and meaningful data sets. In fact this reduces the inherently transient data set into a time independent mean data set. Forward computation were carried out with CFD code for various case to generate a large set of data to train the ANN. Specific signature analysis was carried out to find the parameters of interest for ANN training like peak concentration, time to reach peak concentration and time to fall, the ANN was trained with data and source strength and location were predicted from ANN. Inverse problem was performed using ANN approach in long range atmospheric dispersion. An illustration of application of CFD code for atmospheric dispersion studies for a hypothetical case is also included in the paper. (author)

Optimization of thermal conductivity lightweight brick type AAC (Autoclaved Aerated Concrete) effect of Si & Ca composition by using Artificial Neural Network (ANN)

Science.gov (United States)

Zulkifli; Wiryawan, G. P.

2018-03-01

Lightweight brick is the most important component of building construction, therefore it is necessary to have lightweight thermal, mechanical and aqustic thermal properties that meet the standard, in this paper which is discussed is the domain of light brick thermal conductivity properties. The advantage of lightweight brick has a low density (500-650 kg/m3), more economical, can reduce the load 30-40% compared to conventional brick (clay brick). In this research, Artificial Neural Network (ANN) is used to predict the thermal conductivity of lightweight brick type Autoclaved Aerated Concrete (AAC). Based on the training and evaluation that have been done on 10 model of ANN with number of hidden node 1 to 10, obtained that ANN with 3 hidden node have the best performance. It is known from the mean value of MSE (Mean Square Error) validation for three training times of 0.003269. This ANN was further used to predict the thermal conductivity of four light brick samples. The predicted results for each of the AAC1, AAC2, AAC3 and AAC4 light brick samples were 0.243 W/m.K, respectively; 0.29 W/m.K; 0.32 W/m.K; and 0.32 W/m.K. Furthermore, ANN is used to determine the effect of silicon composition (Si), Calcium (Ca), to light brick thermal conductivity. ANN simulation results show that the thermal conductivity increases with increasing Si composition. Si content is allowed maximum of 26.57%, while the Ca content in the range 20.32% - 30.35%.

Heteroleptic metallosupramolecular racks, rectangles, and trigonal prisms: stoichiometry-controlled reversible interconversion.

Science.gov (United States)

Neogi, Subhadip; Lorenz, Yvonne; Engeser, Marianne; Samanta, Debabrata; Schmittel, Michael

2013-06-17

A simple approach toward preparation of heteroleptic two-dimensional (2D) rectangles and three-dimensional (3D) triangular prisms is described utilizing the HETPYP (HETeroleptic PYridyl and Phenanthroline metal complexes) concept. By mixing metal-loaded linear bisphenanthrolines of varying lengths with diverse (multi)pyridine (py) ligands in a proper ratio, six different self-assembled architectures arise cleanly and spontaneously in the absence of any template. They are characterized by (1)H and DOSY NMR, ESI-FT-ICR mass spectrometry as well as by Job plots and UV-vis titrations. Density functional theory (DFT) computations provide information about each structure. A stoichiometry-controlled supramolecule-to-supramolecule interconversion based on the relative amounts of metal bisphenanthroline and bipyridine forces the rectangular assembly to reorganize to a rack architecture and back to the rectangle, as clearly supported by variable temperature and DOSY NMR as well as dynamic light scattering data. The highly dynamic nature of the assemblies represents a promising starting point for constitutional dynamic materials.

Safety Assessment of Multi Purpose Small Payload Rack(MSPR)

Science.gov (United States)

Mizutani, Yoshinobu; Takada, Satomi; Murata, Kosei; Ozawa, Daisaku; Kobayashi, Ryoji; Nakamura, Yasuhiro

2010-09-01

We are reporting summary of preliminary safety assessment for Multi Purpose Small Payload Rack(MSPR), which is one of the micro gravity experiment facilities that are being developed for the 2nd phase JEM utilization(JEM: Japanese Experiment Module) that will be launched on H-II Transfer Vehicle(HTV) 2nd flight in 2011. MSPR is used for multi-purpose micro-g experiment providing experimental spaces and work stations. MSPR has three experimental spaces; first, there is a space called Work Volume(WV) with capacity volume of approximately 350 litters, in which multiple resources including electricity, communication, and moving image functions can be used. Within this space, installation of devices can be done by simple, prompt attachment by Velcro and pins with high degree of flexibility. Second, there is Small Experiment Area(SEA), with capacity volume of approximately 70 litters, in which electricity, communication, and moving image functions can also be used in the same way as WV. These spaces protect experiment devices and specimens from contingent loads by the crewmembers. Third, there is Work Bench with area of 0.5 square meters, on which can be used for maintenance, inspection and data operations of installed devices, etc. This bench can be stored in the rack during contingency. Chamber for Combustion Experiment(CCE) that is planned to be installed in WV is a pressure-resistant experimental container that can be used to seal hazardous materials from combustion experiments. This CCE has double sealing design in chamber itself, which resist gas leakage under normal the temperature and pressure. Electricity, communication, moving image function can be used in the same way as WV. JAXA Phase 2 Safety Review Panel(SRP) has been held in April, 2010. For safety analysis of MSPR, hazards were identified based on Fault Tree Analysis methodology and then these hazards were classified into either eight ISS standard-type hazards or eight unique-type hazards that requires

Exploration of artificial neural network [ANN] to predict the electrochemical characteristics of lithium-ion cells

Energy Technology Data Exchange (ETDEWEB)

Parthiban, Thirumalai; Ravi, R.; Kalaiselvi, N. [Central Electrochemical Research Institute (CECRI), Karaikudi 630006 (India)

2007-12-31

CoO anode, as an alternate to the carbonaceous anodes of lithium-ion cells has been prepared and investigated for electrochemical charge-discharge characteristics for about 50 cycles. Artificial neural networks (ANNs), which are useful in estimating battery performance, has been deployed for the first time to forecast and to verify the charge-discharge behavior of lithium-ion cells containing CoO anode for a total of 50 cycles. In this novel approach, ANN that has one input layer with one neuron corresponding to one input variable, viz., cycles [charge-discharge cycles] and a hidden layer consisting of three neurons to produce their outputs to the output layer through a sigmoid function has been selected for the present investigation. The output layer consists of two neurons, representing the charge and discharge capacity, whose activation function is also the sigmoid transfer function. In this ever first attempt to exploit ANN as an effective theoretical tool to understand the charge-discharge characteristics of lithium-ion cells, an excellent agreement between the calculated and observed capacity values was found with CoO anodes with the best fit values corresponding to an error factor of <1%, which is the highlight of the present study. (author)

A Woman Voice in an Epic: Tracing Gendered Motifs in Anne Vabarna's Peko

Directory of Open Access Journals (Sweden)

Andreas Kalkun

2008-12-01

Full Text Available In the article the gendered motifs found in Anne Vabarna’s Seto epic Peko are analysed. Besides the narrative telling of the life of the male hero, the motives regarding eating, refusing to eat or offering food, and the aspect of the female body or its control deserve to be noticed. These scenes do not communicate the main plot, they are often related to minor characters of the epic and slow down the narrative, but at the same time they clearly carry artistic purpose and meaning. I consider these motifs, present in the liminal parts of the epic, to be the dominant symbols of the epic where the author’s feminine world is being exposed. Observing these motifs of Peko in the context of Seto religious worldview, the life of Anne Vabarna and the social position of Seto women, the symbols become eloquent and informative.

La presa di parola di Anne Hutchinson. Insubordinazione e conflitto nella giovane America puritana

Directory of Open Access Journals (Sweden)

Itala Vivan

2016-04-01

Full Text Available Anne Hutchinson lasciò l’Inghilterra nel 1634 per emigrare nel Massachusetts puritano, dove nel 1637 e 1638 fu processata, condannata, scomunicata ed espulsa come donna insubordinata, deviante e pericolosa. Il suo ruolo intellettuale e politico nell’alba incandescente della prima America viene qui analizzato e discusso ascoltando da presso il racconto che promana dalla voce della stessa Anne Hutchinson attraverso i verbali dei due processi, trascritti dai contemporanei con la fedeltà letterale che era tipica del puritanesimo americano. La drammatica controversia che ebbe al centro la presa di parola di questa donna segnò la prima grande crisi della neonata società coloniale – la cosiddetta crisi antinomiana -- e ne determinò gli sviluppi futuri, indirizzandoli verso un sistema di potere politico su basi teocratiche.

ANN Surface Roughness Optimization of AZ61 Magnesium Alloy Finish Turning: Minimum Machining Times at Prime Machining Costs.

Science.gov (United States)

Abbas, Adel Taha; Pimenov, Danil Yurievich; Erdakov, Ivan Nikolaevich; Taha, Mohamed Adel; Soliman, Mahmoud Sayed; El Rayes, Magdy Mostafa

2018-05-16

Magnesium alloys are widely used in aerospace vehicles and modern cars, due to their rapid machinability at high cutting speeds. A novel Edgeworth⁻Pareto optimization of an artificial neural network (ANN) is presented in this paper for surface roughness ( Ra ) prediction of one component in computer numerical control (CNC) turning over minimal machining time ( T m ) and at prime machining costs ( C ). An ANN is built in the Matlab programming environment, based on a 4-12-3 multi-layer perceptron (MLP), to predict Ra , T m , and C , in relation to cutting speed, v c , depth of cut, a p , and feed per revolution, f r . For the first time, a profile of an AZ61 alloy workpiece after finish turning is constructed using an ANN for the range of experimental values v c , a p , and f r . The global minimum length of a three-dimensional estimation vector was defined with the following coordinates: Ra = 0.087 μm, T m = 0.358 min/cm³, C = $8.2973. Likewise, the corresponding finish-turning parameters were also estimated: cutting speed v c = 250 m/min, cutting depth a p = 1.0 mm, and feed per revolution f r = 0.08 mm/rev. The ANN model achieved a reliable prediction accuracy of ±1.35% for surface roughness.

DeAnnIso: a tool for online detection and annotation of isomiRs from small RNA sequencing data.

Science.gov (United States)

Zhang, Yuanwei; Zang, Qiguang; Zhang, Huan; Ban, Rongjun; Yang, Yifan; Iqbal, Furhan; Li, Ao; Shi, Qinghua

2016-07-08

Small RNA (sRNA) Sequencing technology has revealed that microRNAs (miRNAs) are capable of exhibiting frequent variations from their canonical sequences, generating multiple variants: the isoforms of miRNAs (isomiRs). However, integrated tool to precisely detect and systematically annotate isomiRs from sRNA sequencing data is still in great demand. Here, we present an online tool, DeAnnIso (Detection and Annotation of IsomiRs from sRNA sequencing data). DeAnnIso can detect all the isomiRs in an uploaded sample, and can extract the differentially expressing isomiRs from paired or multiple samples. Once the isomiRs detection is accomplished, detailed annotation information, including isomiRs expression, isomiRs classification, SNPs in miRNAs and tissue specific isomiR expression are provided to users. Furthermore, DeAnnIso provides a comprehensive module of target analysis and enrichment analysis for the selected isomiRs. Taken together, DeAnnIso is convenient for users to screen for isomiRs of their interest and useful for further functional studies. The server is implemented in PHP + Perl + R and available to all users for free at: http://mcg.ustc.edu.cn/bsc/deanniso/ and http://mcg2.ustc.edu.cn/bsc/deanniso/. © The Author(s) 2016. Published by Oxford University Press on behalf of Nucleic Acids Research.

Staphylococcus xylosus PCR-validated Decontamination of Murine Individually Ventilated Cage Racks and Air Handling Units by Using 'Active-Closed' Exposure to Vaporized Hydrogen Peroxide.

Science.gov (United States)

Ragland, Natalie H; Miedel, Emily L; Gomez, Jose M; Engelman, Robert W

2017-11-01

Vaporized hydrogen peroxide (VHP) is used to decontaminate clinical, biocontainment, and research animal rooms and equipment. To assist with its implementation in a murine facility, we developed a safe and effective method of VHP sterilization of IVC racks and air handling units (AHU). Safety of VHP decontamination was assessed by ensuring VHP levels dissipated to less than 1 ppm in the room prior to personnel reentry and inside the primary enclosure prior to the return of mice; this condition occurred at least 18 h after the VHP cycle. Efficacy of VHP sterilization was assessed by using chemical indicators, biologic indicators, and PCR testing for Staphylococcus xylosus, a commensal organism of murine skin and an opportunistic pathogen, which was present in 160 of 172 (93%) of specimens from occupied IVC racks and the interior surfaces of in-use AHU. Neither mechanized washing nor hand-sanitizing eradicated S. xylosus from equipment airway interiors, with 17% to 24% of specimens remaining PCR-positive for S. xylosus. 'Static-open' VHP exposure of sanitized equipment did not ensure its sterilization. In contrast, 'active-closed' VHP exposure, in which IVC racks were assembled, sealed, and connected to AHU set to the VHP cycle, increased the proportion of chemical indicators that detected sterilizing levels of VHP inside the assembled equipment, and significantly decreased PCR-detectable S. xylosus inside the equipment. Supplementing bulk steam sterilization of the primary enclosure with VHP sterilization of the secondary housing equipment during room change-outs may help to mitigate opportunistic agents that jeopardize studies involving immunodeficient strains.

ANN-based calibration model of FTIR used in transformer online monitoring

Science.gov (United States)

Li, Honglei; Liu, Xian-yong; Zhou, Fangjie; Tan, Kexiong

2005-02-01

Recently, chromatography column and gas sensor have been used in online monitoring device of dissolved gases in transformer oil. But some disadvantages still exist in these devices: consumption of carrier gas, requirement of calibration, etc. Since FTIR has high accuracy, consume no carrier gas and require no calibration, the researcher studied the application of FTIR in such monitoring device. Experiments of "Flow gas method" were designed, and spectrum of mixture composed of different gases was collected with A BOMEM MB104 FTIR Spectrometer. A key question in the application of FTIR is that: the absorbance spectrum of 3 fault key gases, including C2H4, CH4 and C2H6, are overlapped seriously at 2700~3400cm-1. Because Absorbance Law is no longer appropriate, a nonlinear calibration model based on BP ANN was setup to in the quantitative analysis. The height absorbance of C2H4, CH4 and C2H6 were adopted as quantitative feature, and all the data were normalized before training the ANN. Computing results show that the calibration model can effectively eliminate the cross disturbance to measurement.

ANN-GA based optimization of a high ash coal-fired supercritical power plant

International Nuclear Information System (INIS)

Suresh, M.V.J.J.; Reddy, K.S.; Kolar, Ajit Kumar

2011-01-01

Highlights: → Neuro-genetic power plant optimization is found to be an efficient methodology. → Advantage of neuro-genetic algorithm is the possibility of on-line optimization. → Exergy loss in combustor indicates the effect of coal composition on efficiency. -- Abstract: The efficiency of coal-fired power plant depends on various operating parameters such as main steam/reheat steam pressures and temperatures, turbine extraction pressures, and excess air ratio for a given fuel. However, simultaneous optimization of all these operating parameters to achieve the maximum plant efficiency is a challenging task. This study deals with the coupled ANN and GA based (neuro-genetic) optimization of a high ash coal-fired supercritical power plant in Indian climatic condition to determine the maximum possible plant efficiency. The power plant simulation data obtained from a flow-sheet program, 'Cycle-Tempo' is used to train the artificial neural network (ANN) to predict the energy input through fuel (coal). The optimum set of various operating parameters that result in the minimum energy input to the power plant is then determined by coupling the trained ANN model as a fitness function with the genetic algorithm (GA). A unit size of 800 MWe currently under development in India is considered to carry out the thermodynamic analysis based on energy and exergy. Apart from optimizing the design parameters, the developed model can also be used for on-line optimization when quick response is required. Furthermore, the effect of various coals on the thermodynamic performance of the optimized power plant is also determined.

Energy Performance Testing of Asetek's RackCDU System at NREL's High Performance Computing Data Center

Energy Technology Data Exchange (ETDEWEB)

Sickinger, D.; Van Geet, O.; Ravenscroft, C.

2014-11-01

In this study, we report on the first tests of Asetek's RackCDU direct-to-chip liquid cooling system for servers at NREL's ESIF data center. The system was simple to install on the existing servers and integrated directly into the data center's existing hydronics system. The focus of this study was to explore the total cooling energy savings and potential for waste-heat recovery of this warm-water liquid cooling system. RackCDU captured up to 64% of server heat into the liquid stream at an outlet temperature of 89 degrees F, and 48% at outlet temperatures approaching 100 degrees F. This system was designed to capture heat from the CPUs only, indicating a potential for increased heat capture if memory cooling was included. Reduced temperatures inside the servers caused all fans to reduce power to the lowest possible BIOS setting, indicating further energy savings potential if additional fan control is included. Preliminary studies manually reducing fan speed (and even removing fans) validated this potential savings but could not be optimized for these working servers. The Asetek direct-to-chip liquid cooling system has been in operation with users for 16 months with no necessary maintenance and no leaks.

Anmeldelse: Anne Gjelsvik & Rikke Schubart : Women of ice and fire: Gender, Game of Thrones, and multiple media engagements, New York/London: Bloomsbury, 2016

DEFF Research Database (Denmark)

Konzack, Lars

2017-01-01

Anmeldelse af bogen Women of Ice and F ire: Gender, Game of Thrones redigeret af Anne Gjelsvik & Rikke Schubart.......Anmeldelse af bogen Women of Ice and F ire: Gender, Game of Thrones redigeret af Anne Gjelsvik & Rikke Schubart....

Implementation of ANN on CCHP system to predict trigeneration performance with consideration of various operative factors

International Nuclear Information System (INIS)

Anvari, Simin; Taghavifar, Hadi; Saray, Rahim Khoshbakhti; Khalilarya, Shahram; Jafarmadar, Samad

2015-01-01

Highlights: • ANN modeling tool was implemented on the CCHP system. • The best ANN topology was detected 10–8–9 with Levenberg–Marquadt algorithm. • The system is more sensitive of CC outlet temperature and turbine isentropic efficiency. • The lowest RMSE = 3.13e−5 and the best R 2 = 0.999 is related to lambda and second law efficiency terms, respectively. - Abstract: A detailed investigation was aimed based on numerical thermodynamic survey and artificial neural network (ANN) modeling of the trigeneration system. The results are presented in two pivotal frameworks namely the sensitivity analysis and ANN prediction capability of proposed modeling. The underlying operative parameters were chosen as input parameters from different cycles and components, while the exergy efficiency, exergy loss, coefficient of performance, heating load exergy, lambda, gas turbine power, exergy destruction, actual outlet air compressor temperature, and heat recovery gas steam generator (HRSG) outlet temperature were taken as objective output parameters for the modeling purpose. Up to now, no significant step was taken to investigate the compound power plant with thermodynamic analyses and network predictability hybrid in such a detailed oriented approach. It follows that multilayer perceptron neural network with back propagation algorithm deployed with 10–8–9 configuration results in the modeling reliability ranged within R 2 = 0.995–0.999. When dataset treated with trainlm learning algorithm and diversified neurons, the mean square error (MSE) is obtained equal to 0.2175. This denotes a powerful modeling achievement in both scientific and industrial scale to save considerable computational cost on combined cooling, heating, and power system in accomplishment of boosting the energy efficiency and system maintenance

Application of Artificial Neural Networks (ANNs for Weight Predictions of Blue Crabs (Callinectes sapidus RATHBUN, 1896 Using Predictor Variables

Directory of Open Access Journals (Sweden)

C. TURELI BILEN

2011-10-01

Full Text Available An evaluation of the performance of artificial networks (ANNs to estimate the weights of blue crab (Callinectes sapidus catches in Yumurtalık Cove (Iskenderun Bay that uses measured predictor variables is presented, including carapace width (CW, sex (male, female and female with eggs, and sampling month. Blue crabs (n=410 were collected each month between 15 September 1996 and 15 May 1998. Sex, CW, and sampling month were used and specified in the input layer of the network. The weights of the blue crabs were utilized in the output layer of the network. A multi-layer perception architecture model was used and was calibrated with the Levenberg Marguardt (LM algorithm. Finally, the values were determined by the ANN model using the actual data. The mean square error (MSE was measured as 3.3, and the best results had a correlation coefficient (R of 0.93. We compared the predictive capacity of the general linear model (GLM versus the Artificial Neural Network model (ANN for the estimation of the weights of blue crabs from independent field data. The results indicated the higher performance capacity of the ANN to predict weights compared to the GLM (R=0.97 vs. R=0.95, raw variable when evaluated against independent field data.

Development of LC-MS determination method and back-propagation ANN pharmacokinetic model of corynoxeine in rat.

Science.gov (United States)

Ma, Jianshe; Cai, Jinzhang; Lin, Guanyang; Chen, Huilin; Wang, Xianqin; Wang, Xianchuan; Hu, Lufeng

2014-05-15

Corynoxeine(CX), isolated from the extract of Uncaria rhynchophylla, is a useful and prospective compound in the prevention and treatment for vascular diseases. A simple and selective liquid chromatography mass spectrometry (LC-MS) method was developed to determine the concentration of CX in rat plasma. The chromatographic separation was achieved on a Zorbax SB-C18 (2.1 mm × 150 mm, 5 μm) column with acetonitrile-0.1% formic acid in water as mobile phase. Selective ion monitoring (SIM) mode was used for quantification using target ions m/z 383 for CX and m/z 237 for the carbamazepine (IS). After the LC-MS method was validated, it was applied to a back-propagation artificial neural network (BP-ANN) pharmacokinetic model study of CX in rats. The results showed that after intravenous administration of CX, it was mainly distributed in blood and eliminated quickly, t1/2 was less than 1h. The predicted concentrations generated by BP-ANN model had a high correlation coefficient (R>0.99) with experimental values. The developed BP-ANN pharmacokinetic model can be used to predict the concentration of CX in rats. Copyright © 2014 Elsevier B.V. All rights reserved.

Simulation of CO2 Solubility in Polystyrene-b-Polybutadieneb-Polystyrene (SEBS) by artificial intelligence network (ANN) method

Science.gov (United States)

Sharudin, R. W.; AbdulBari Ali, S.; Zulkarnain, M.; Shukri, M. A.

2018-05-01

This study reports on the integration of Artificial Neural Network (ANNs) with experimental data in predicting the solubility of carbon dioxide (CO2) blowing agent in SEBS by generating highest possible value for Regression coefficient (R2). Basically, foaming of thermoplastic elastomer with CO2 is highly affected by the CO2 solubility. The ability of ANN in predicting interpolated data of CO2 solubility was investigated by comparing training results via different method of network training. Regards to the final prediction result for CO2 solubility by ANN, the prediction trend (output generate) was corroborated with the experimental results. The obtained result of different method of training showed the trend of output generated by Gradient Descent with Momentum & Adaptive LR (traingdx) required longer training time and required more accurate input to produce better output with final Regression Value of 0.88. However, it goes vice versa with Levenberg-Marquardt (trainlm) technique as it produced better output in quick detention time with final Regression Value of 0.91.

Facteurs prédictifs de succès des étudiants en première année de ...

African Journals Online (AJOL)

Introduction: Plusieurs facteurs dont les notes obtenues au BAC peuvent influencer les performances académiques des étudiants en première année de médecine. L'objectif de cette étude était d'évaluer la relation entre les résultats des étudiants au BAC et le succès en première année de médecine. Méthodes: Nous ...

[The embroidery work of the lady at Saint-Anne Hospital].

Science.gov (United States)

Thillaud, Pierre L; Postel, Jacques

2014-01-01

In July 1974, a 72 old woman had been a patient for forty years in Sainte-Anne Hospital, Ward C. As she had again a violent brawl with her neighbour patient, she revealed being a tremendous artist. She had been confined on account of dementia paralytica in the Mecca of malariotherapy, and passionately devoted herself to embroidery. Her fancy work was rather a matter for Jean Dubuffet's art through its perfect expression and deserved being known.

ECONOMIC EVALUATION OF MAINTAINING THE CAPACITY OF TRASH RACKS IN HYDRAULIC ENGINEERING STRUCTURES

Directory of Open Access Journals (Sweden)

Natalia Walczak

2017-05-01

Full Text Available Considering the limited capabilities of obtaining energy in a traditional way from coal combustion and the requirements of the European Union, other alternative energy sources should be sought. They have been being increasingly used by business entities and individual investors and are designed to provide financial profits, which will be ensured only with correct operation of the energy system. One of examples of alternative energy sources application is the construction of small hydropower plants, where the efficiency of all elements included is of great importance. The article analyses financial losses incurred by owners of power plants when the energy system lacks 100% capacity of the inlet channel. Material that accumulates on SHP trash racks might be analysed in two ways: biologically (these are screenings – as in wastewater treatment plants and hydraulically.

"Boob teab" / Kalju Komissarov ja Rait Avestik ; kommenteerinud ja toimetanud Anneli Saro

Index Scriptorium Estoniae

Komissarov, Kalju, 1946-2017

2010-01-01

Teatriseminar sarjast "Eesti algupärandid Eesti teatris" toimus Tartu Kirjanduse Maja krüptis 28. märtsil 2005, seminari juhtis Anneli Saro. Urmas Lennuki näidendi kolmest lavastusest: Tallinna Linnateatris (esietendus 28. veebruaril 2004, lavastas Jaanus Rohumaa), Rakvere Teatris (esietendus 10. septembril 2004, lavastas Kalju Komissarov) ja Vikerraadios (esietendus 4. septembril 2004, lavastas Tamur Tohver)

78 FR 65382 - Notice of Inventory Completion: University of Michigan, Ann Arbor, MI

Science.gov (United States)

2013-10-31

....S.C. 3003, of the completion of an inventory of human remains under the control of the University of....R50000] Notice of Inventory Completion: University of Michigan, Ann Arbor, MI AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The University of Michigan has completed an inventory of human...

78 FR 65369 - Notice of Inventory Completion: University of Michigan, Ann Arbor, MI

Science.gov (United States)

2013-10-31

....S.C. 3003, of the completion of an inventory of human remains under the control of the University of....R50000] Notice of Inventory Completion: University of Michigan, Ann Arbor, MI AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The University of Michigan has completed an inventory of human...

78 FR 65366 - Notice of Inventory Completion: University of Michigan, Ann Arbor, MI

Science.gov (United States)

2013-10-31

....S.C. 3003, of the completion of an inventory of human remains under the control of the University of....R50000] Notice of Inventory Completion: University of Michigan, Ann Arbor, MI AGENCY: National Park Service, Interior. ACTION: Notice. SUMMARY: The University of Michigan has completed an inventory of human...

Staphylococcus xylosus PCR-validated Decontamination of Murine Individually Ventilated Cage Racks and Air Handling Units by Using ‘Active–Closed’ Exposure to Vaporized Hydrogen Peroxide

Science.gov (United States)

Ragland, Natalie H; Miedel, Emily L; Gomez, Jose M; Engelman, Robert W

2017-01-01

Vaporized hydrogen peroxide (VHP) is used to decontaminate clinical, biocontainment, and research animal rooms and equipment. To assist with its implementation in a murine facility, we developed a safe and effective method of VHP sterilization of IVC racks and air handling units (AHU). Safety of VHP decontamination was assessed by ensuring VHP levels dissipated to less than 1 ppm in the room prior to personnel reentry and inside the primary enclosure prior to the return of mice; this condition occurred at least 18 h after the VHP cycle. Efficacy of VHP sterilization was assessed by using chemical indicators, biologic indicators, and PCR testing for Staphylococcus xylosus, a commensal organism of murine skin and an opportunistic pathogen, which was present in 160 of 172 (93%) of specimens from occupied IVC racks and the interior surfaces of in-use AHU. Neither mechanized washing nor hand-sanitizing eradicated S. xylosus from equipment airway interiors, with 17% to 24% of specimens remaining PCR-positive for S. xylosus. ‘Static–open’ VHP exposure of sanitized equipment did not ensure its sterilization. In contrast, ‘active–closed’ VHP exposure, in which IVC racks were assembled, sealed, and connected to AHU set to the VHP cycle, increased the proportion of chemical indicators that detected sterilizing levels of VHP inside the assembled equipment, and significantly decreased PCR-detectable S. xylosus inside the equipment. Supplementing bulk steam sterilization of the primary enclosure with VHP sterilization of the secondary housing equipment during room change-outs may help to mitigate opportunistic agents that jeopardize studies involving immunodeficient strains. PMID:29256369

Performance evaluation of an irreversible Miller cycle comparing FTT (finite-time thermodynamics) analysis and ANN (artificial neural network) prediction

International Nuclear Information System (INIS)

Mousapour, Ashkan; Hajipour, Alireza; Rashidi, Mohammad Mehdi; Freidoonimehr, Navid

2016-01-01

In this paper, the first and second-laws efficiencies are applied to performance analysis of an irreversible Miller cycle. In the irreversible cycle, the linear relation between the specific heat of the working fluid and its temperature, the internal irreversibility described using the compression and expansion efficiencies, the friction loss computed according to the mean velocity of the piston and the heat-transfer loss are considered. The effects of various design parameters, such as the minimum and maximum temperatures of the working fluid and the compression ratio on the power output and the first and second-laws efficiencies of the cycle are discussed. In the following, a procedure named ANN is used for predicting the thermal efficiency values versus the compression ratio, and the minimum and maximum temperatures of the Miller cycle. Nowadays, Miller cycle is widely used in the automotive industry and the obtained results of this study will provide some significant theoretical grounds for the design optimization of the Miller cycle. - Highlights: • The performance of an irreversible Miller cycle is investigated using FFT. • The effects of design parameters on the performance of the cycle are investigated. • ANN is applied to predict the thermal efficiency and the power output values. • There is an excellent correlation between FTT and ANN data. • ANN can be applied to predict data where FTT analysis has not been performed.

Statistical optimization of the phytoremediation of arsenic by Ludwigia octovalvis- in a pilot reed bed using response surface methodology (RSM) versus an artificial neural network (ANN).

Science.gov (United States)

Titah, Harmin Sulistiyaning; Halmi, Mohd Izuan Effendi Bin; Abdullah, Siti Rozaimah Sheikh; Hasan, Hassimi Abu; Idris, Mushrifah; Anuar, Nurina

2018-06-07

In this study, the removal of arsenic (As) by plant, Ludwigia octovalvis, in a pilot reed bed was optimized. A Box-Behnken design was employed including a comparative analysis of both Response Surface Methodology (RSM) and an Artificial Neural Network (ANN) for the prediction of maximum arsenic removal. The predicted optimum condition using the desirability function of both models was 39 mg kg -1 for the arsenic concentration in soil, an elapsed time of 42 days (the sampling day) and an aeration rate of 0.22 L/min, with the predicted values of arsenic removal by RSM and ANN being 72.6% and 71.4%, respectively. The validation of the predicted optimum point showed an actual arsenic removal of 70.6%. This was achieved with the deviation between the validation value and the predicted values being within 3.49% (RSM) and 1.87% (ANN). The performance evaluation of the RSM and ANN models showed that ANN performs better than RSM with a higher R 2 (0.97) close to 1.0 and very small Average Absolute Deviation (AAD) (0.02) and Root Mean Square Error (RMSE) (0.004) values close to zero. Both models were appropriate for the optimization of arsenic removal with ANN demonstrating significantly higher predictive and fitting ability than RSM.

Evaluation of Effectiveness of Wavelet Based Denoising Schemes Using ANN and SVM for Bearing Condition Classification

Directory of Open Access Journals (Sweden)

Vijay G. S.

2012-01-01

Full Text Available The wavelet based denoising has proven its ability to denoise the bearing vibration signals by improving the signal-to-noise ratio (SNR and reducing the root-mean-square error (RMSE. In this paper seven wavelet based denoising schemes have been evaluated based on the performance of the Artificial Neural Network (ANN and the Support Vector Machine (SVM, for the bearing condition classification. The work consists of two parts, the first part in which a synthetic signal simulating the defective bearing vibration signal with Gaussian noise was subjected to these denoising schemes. The best scheme based on the SNR and the RMSE was identified. In the second part, the vibration signals collected from a customized Rolling Element Bearing (REB test rig for four bearing conditions were subjected to these denoising schemes. Several time and frequency domain features were extracted from the denoised signals, out of which a few sensitive features were selected using the Fisher’s Criterion (FC. Extracted features were used to train and test the ANN and the SVM. The best denoising scheme identified, based on the classification performances of the ANN and the SVM, was found to be the same as the one obtained using the synthetic signal.

IDI diesel engine performance and exhaust emission analysis using biodiesel with an artificial neural network (ANN

Directory of Open Access Journals (Sweden)

K. Prasada Rao

2017-09-01

Full Text Available Biodiesel is receiving increasing attention each passing day because of its fuel properties and compatibility. This study investigates the performance and emission characteristics of single cylinder four stroke indirect diesel injection (IDI engine fueled with Rice Bran Methyl Ester (RBME with Isopropanol additive. The investigation is done through a combination of experimental data analysis and artificial neural network (ANN modeling. The study used IDI engine experimental data to evaluate nine engine performance and emission parameters including Exhaust Gas Temperature (E.G.T, Brake Specific Fuel Consumption (BSFC, Brake Thermal Efficiency (B.The and various emissions like Hydrocarbons (HC, Carbon monoxide (CO, Carbon dioxide (CO2, Oxygen (O2, Nitrogen oxides (NOX and smoke. For the ANN modeling standard back propagation algorithm was found to be the optimum choice for training the model. A multi-layer perception (MLP network was used for non-linear mapping between the input and output parameters. It was found that ANN was able to predict the engine performance and exhaust emissions with a correlation coefficient of 0.995, 0.980, 0.999, 0.985, 0.999, 0.999, 0.980, 0.999, and 0.999 for E.G.T, BSFC, B.The, HC, O2, CO2, CO, NOX, smoke respectively.

Strategic planning for minimizing CO2 emissions using LP model based on forecasted energy demand by PSO Algorithm and ANN

Energy Technology Data Exchange (ETDEWEB)

Yousefi, M.; Omid, M.; Rafiee, Sh. [Department of Agricultural Machinery Engineering, University of Tehran, Karaj (Iran, Islamic Republic of); Ghaderi, S. F. [Department of Industrial Engineering, University of Tehran, Tehran (Iran, Islamic Republic of)

2013-07-01

Iran's primary energy consumption (PEC) was modeled as a linear function of five socioeconomic and meteorological explanatory variables using particle swarm optimization (PSO) and artificial neural networks (ANNs) techniques. Results revealed that ANN outperforms PSO model to predict test data. However, PSO technique is simple and provided us with a closed form expression to forecast PEC. Energy demand was forecasted by PSO and ANN using represented scenario. Finally, adapting about 10% renewable energy revealed that based on the developed linear programming (LP) model under minimum CO2 emissions, Iran will emit about 2520 million metric tons CO2 in 2025. The LP model indicated that maximum possible development of hydropower, geothermal and wind energy resources will satisfy the aim of minimization of CO2 emissions. Therefore, the main strategic policy in order to reduce CO2 emissions would be exploitation of these resources.

Dynamically stable associative learning: a neurobiologically based ANN and its applications

Science.gov (United States)

Vogl, Thomas P.; Blackwell, Kim L.; Barbour, Garth; Alkon, Daniel L.

1992-07-01

Most currently popular artificial neural networks (ANN) are based on conceptions of neuronal properties that date back to the 1940s and 50s, i.e., to the ideas of McCullough, Pitts, and Hebb. Dystal is an ANN based on current knowledge of neurobiology at the cellular and subcellular level. Networks based on these neurobiological insights exhibit the following advantageous properties: (1) A theoretical storage capacity of bN non-orthogonal memories, where N is the number of output neurons sharing common inputs and b is the number of distinguishable (gray shade) levels. (2) The ability to learn, store, and recall associations among noisy, arbitrary patterns. (3) A local synaptic learning rule (learning depends neither on the output of the post-synaptic neuron nor on a global error term), some of whose consequences are: (4) Feed-forward, lateral, and feed-back connections (as well as time-sensitive connections) are possible without alteration of the learning algorithm; (5) Storage allocation (patch creation) proceeds dynamically as associations are learned (self- organizing); (6) The number of training set presentations required for learning is small (different expressions and/or corrupted by noise, and on reading hand-written digits (98% accuracy) and hand-printed Japanese Kanji (90% accuracy) is demonstrated.

Friendly Letters on the Correspondence of Helen Keller, Anne Sullivan, and Alexander Graham Bell.

Science.gov (United States)

Blatt, Burton

1985-01-01

Excerpts from the letters between Alexander Graham Bell and Anne Sullivan and Helen Keller are given to illustrate the educational and personal growth of Helen Keller as well as the educational philosophy of Bell regarding the education of the deaf blind. (DB)

'In the developed world, people talk and shop'- a review by Anne ...

African Journals Online (AJOL)

'In the developed world, people talk and shop'- a review by Anne Derges. A. Salleh. http://dx.doi.org/10.4314/safere.v3i1.23966 · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions of Use · Contact AJOL ...

Prophecy, patriarchy, and violence in the early modern household: the revelations of Anne Wentworth.

Science.gov (United States)

Johnston, Warren

2009-10-01

In 1676 the apostate Baptist prophet Anne Wentworth (1629/30-1693?) published "A True Account of Anne Wentworths Being Cruelly, Unjustly, and Unchristianly Dealt with by Some of Those People called Anabaptists," the first in a series of pamphlets that would continue to the end of the decade. Orignially a member of a London Baptist church, Wentworth left the congregation and eventually her own home after her husband used physical force to stop her writing and prophesying. Yet Wentworth persisted in her "revelations." These prophecies increasingly focused on her response to those who were trying to stop her efforts, especially within her own household. This article examines Wentworth's writings as an effort by an early modern woman, using arguments of spiritual agency, to assert ideas about proper gender roles and household responsibilities to denounce her husband and rebut those who criticized and attempted to suppress her.

Rapid Identification of Asteraceae Plants with Improved RBF-ANN Classification Models Based on MOS Sensor E-Nose

Directory of Open Access Journals (Sweden)

Hui-Qin Zou

2014-01-01

Full Text Available Plants from Asteraceae family are widely used as herbal medicines and food ingredients, especially in Asian area. Therefore, authentication and quality control of these different Asteraceae plants are important for ensuring consumers’ safety and efficacy. In recent decades, electronic nose (E-nose has been studied as an alternative approach. In this paper, we aim to develop a novel discriminative model by improving radial basis function artificial neural network (RBF-ANN classification model. Feature selection algorithms, including principal component analysis (PCA and BestFirst + CfsSubsetEval (BC, were applied in the improvement of RBF-ANN models. Results illustrate that in the improved RBF-ANN models with lower dimension data classification accuracies (100% remained the same as in the original model with higher-dimension data. It is the first time to introduce feature selection methods to get valuable information on how to attribute more relevant MOS sensors; namely, in this case, S1, S3, S4, S6, and S7 show better capability to distinguish these Asteraceae plants. This paper also gives insights to further research in this area, for instance, sensor array optimization and performance improvement of classification model.

Comparison of the accuracy of SST estimates by artificial neural networks (ANN) and other quantitative methods using radiolarian data from the Antarctic and Pacific Oceans

Digital Repository Service at National Institute of Oceanography (India)

Gupta, S.M.; Malmgren, B.A.

) regression, the maximum likelihood (ML) method, and artificial neural networks (ANNs), based on radiolarian faunal abundance data from surface sediments from the Antarctic and Pacific Oceans. Recent studies have suggested that ANNs may represent one...

Evaluation Of The Advanced Operating System Of The Ann Arbor Transportation Authority : AATA Web Survey

Science.gov (United States)

1999-01-01

During 1997, visitors to the Ann Arbor (Michigan) Transportation Authority's worldwide web site were invited to complete an electronic questionnaire about their experience with the site. Eighty surveys were collected, representing a non-scientific se...

Tallinna Ülikool / Leif Kalev, Anneli Leinpere, Tiit Land, Alessandro Centonze, Hannes Palang, Liis Kelberg

Index Scriptorium Estoniae

2008-01-01

Ülikooli ja seal õpetatavaid erialasid tutvustavad dotsent Leif Kalev, kunstimagistrant Anneli Leinpere, professor Tiit Land, välisüliõpilane Milanost Alessandro Centonze, vanemteadur Hannes Palang ning kirjaliku tõlke magistrant Liis Kelberg

A Comparison of SWAT and ANN Models for Daily Runoff Simulation in Different Climatic Zones of Peninsular Spain

Directory of Open Access Journals (Sweden)

Patricia Jimeno-Sáez

2018-02-01

Full Text Available Streamflow data are of prime importance to water-resources planning and management, and the accuracy of their estimation is very important for decision making. The Soil and Water Assessment Tool (SWAT and Artificial Neural Network (ANN models have been evaluated and compared to find a method to improve streamflow estimation. For a more complete evaluation, the accuracy and ability of these streamflow estimation models was also established separately based on their performance during different periods of flows using regional flow duration curves (FDCs. Specifically, the FDCs were divided into five sectors: very low, low, medium, high and very high flow. This segmentation of flow allows analysis of the model performance for every important discharge event precisely. In this study, the models were applied in two catchments in Peninsular Spain with contrasting climatic conditions: Atlantic and Mediterranean climates. The results indicate that SWAT and ANNs were generally good tools in daily streamflow modelling. However, SWAT was found to be more successful in relation to better simulation of lower flows, while ANNs were superior at estimating higher flows in all cases.

A simulation-optimization heuristic for configuring a selective pallet rack system Heurístico de simulación-optimización para la configuración de un sistema de estantería selectiva simple

Directory of Open Access Journals (Sweden)

Mario C Vélez Gallego

2012-04-01

Full Text Available A discrete event simulation-optimization heuristic is presented for configuring a selective pallet rack system. To the rack system under study pallets arrive dynamically over time to be stored for a given period of time. The storage duration, arrival time and pallet height are assumed to be continuous random variables with known density functions. In such a system, if there is no available slot in the rack to store an arriving pallet, it is placed on the floor. The proposed heuristic aims at minimizing the number of racking banks needed so that the long term proportion of pallets that are placed in a rack slot reaches a minimum pre-specified value. The computational experiments conducted suggest that the proposed heuristic effectively solves the problem under study.En este artículo se presenta un heurístico de simulación-optimización para la configuración de un sistema de almacenamiento en estantería selectiva simple. Al sistema de almacenamiento objeto del estudio llegan pallets dinámicamente en el tiempo para ser almacenados por un periodo de tiempo. Se asume que la duración del almacenamiento, el instante de llegada y la altura de los pallets son variables aleatorias continuas con funciones de densidad conocidas. En este sistema, si al momento de llegada de un pallet no hay disponible una posición en la estantería en la que éste se pueda almacenar, el pallet se almacena en el suelo. El heurístico propuesto busca minimizar en el número de módulos de estantería necesarios de tal manera que en el largo plazo la proporción de pallets ubicados en la estantería alcance un valor mínimo preestablecido. Los experimentos computacionales llevados a cabo sugieren que el heurístico propuesto es efectivo para resolver el problema en estudio.

Estimation of Optimum Dilution in the GMAW Process Using Integrated ANN-GA

Directory of Open Access Journals (Sweden)

P. Sreeraj

2013-01-01

Full Text Available To improve the corrosion resistant properties of carbon steel, usually cladding process is used. It is a process of depositing a thick layer of corrosion resistant material over carbon steel plate. Most of the engineering applications require high strength and corrosion resistant materials for long-term reliability and performance. By cladding these properties can be achieved with minimum cost. The main problem faced on cladding is the selection of optimum combinations of process parameters for achieving quality clad and hence good clad bead geometry. This paper highlights an experimental study to optimize various input process parameters (welding current, welding speed, gun angle, and contact tip to work distance and pinch to get optimum dilution in stainless steel cladding of low carbon structural steel plates using gas metal arc welding (GMAW. Experiments were conducted based on central composite rotatable design with full replication technique, and mathematical models were developed using multiple regression method. The developed models have been checked for adequacy and significance. In this study, artificial neural network (ANN and genetic algorithm (GA techniques were integrated and labeled as integrated ANN-GA to estimate optimal process parameters in GMAW to get optimum dilution.

Strategic planning for minimizing CO2 emissions using LP model based on forecasted energy demand by PSO Algorithm and ANN

Energy Technology Data Exchange (ETDEWEB)

Yousefi, M.; Omid, M.; Rafiee, Sh. [Department of Agricultural Machinery Engineering, University of Tehran, Karaj (Iran, Islamic Republic of); Ghaderi, S.F. [Department of Industrial Engineering, University of Tehran, Tehran (Iran, Islamic Republic of)

2013-07-01

Iran's primary energy consumption (PEC) was modeled as a linear function of five socioeconomic and meteorological explanatory variables using particle swarm optimization (PSO) and artificial neural networks (ANNs) techniques. Results revealed that ANN outperforms PSO model to predict test data. However, PSO technique is simple and provided us with a closed form expression to forecast PEC. Energy demand was forecasted by PSO and ANN using represented scenario. Finally, adapting about 10% renewable energy revealed that based on the developed linear programming (LP) model under minimum CO2 emissions, Iran will emit about 2520 million metric tons CO2 in 2025. The LP model indicated that maximum possible development of hydropower, geothermal and wind energy resources will satisfy the aim of minimization of CO2 emissions. Therefore, the main strategic policy in order to reduce CO2 emissions would be exploitation of these resources.

Using AnnAGNPS to Predict the Effects of Tile Drainage Control on Nutrient and Sediment Loads for a River Basin.

Science.gov (United States)

Que, Z; Seidou, O; Droste, R L; Wilkes, G; Sunohara, M; Topp, E; Lapen, D R

2015-03-01

Controlled tile drainage (CTD) can reduce pollutant loading. The Annualized Agricultural Nonpoint Source model (AnnAGNPS version 5.2) was used to examine changes in growing season discharge, sediment, nitrogen, and phosphorus loads due to CTD for a ∼3900-km agriculturally dominated river basin in Ontario, Canada. Two tile drain depth scenarios were examined in detail to mimic tile drainage control for flat cropland: 600 mm depth (CTD) and 200 mm (CTD) depth below surface. Summed for five growing seasons (CTD), direct runoff, total N, and dissolved N were reduced by 6.6, 3.5, and 13.7%, respectively. However, five seasons of summed total P, dissolved P, and total suspended solid loads increased as a result of CTD by 0.96, 1.6, and 0.23%. The AnnAGNPS results were compared with mass fluxes observed from paired experimental watersheds (250, 470 ha) in the river basin. The "test" experimental watershed was dominated by CTD and the "reference" watershed by free drainage. Notwithstanding environmental/land use differences between the watersheds and basin, comparisons of seasonal observed and predicted discharge reductions were comparable in 100% of respective cases. Nutrient load comparisons were more consistent for dissolved, relative to particulate water quality endpoints. For one season under corn crop production, AnnAGNPS predicted a 55% decrease (CTD) in dissolved N from the basin. AnnAGNPS v. 5.2 treats P transport from a surface pool perspective, which is appropriate for many systems. However, for assessment of tile drainage management practices for relatively flat tile-dominated systems, AnnAGNPS may benefit from consideration of P and particulate transport in the subsurface. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Exact estimation of biodiesel cetane number (CN) from its fatty acid methyl esters (FAMEs) profile using partial least square (PLS) adapted by artificial neural network (ANN)

International Nuclear Information System (INIS)

Hosseinpour, Soleiman; Aghbashlo, Mortaza; Tabatabaei, Meisam; Khalife, Esmail

2016-01-01

Highlights: • Estimating the biodiesel CN from its FAMEs profile using ANN-based PLS approach. • Comparing the capability of ANN-adapted PLS approach with the standard PLS model. • Exact prediction of biodiesel CN from it FAMEs profile using ANN-based PLS method. • Developing an easy-to-use software using ANN-PLS model for computing the biodiesel CN. - Abstract: Cetane number (CN) is among the most important properties of biodiesel because it quantifies combustion speed or in better words, ignition quality. Experimental measurement of biodiesel CN is rather laborious and expensive. However, the high proportionality of biodiesel fatty acid methyl esters (FAMEs) profile with its CN is very appealing to develop straightforward and inexpensive computerized tools for biodiesel CN estimation. Unfortunately, correlating the chemical structure of biodiesel to its CN using conventional statistical and mathematical approaches is very difficult. To solve this issue, partial least square (PLS) adapted by artificial neural network (ANN) was introduced and examined herein as an innovative approach for the exact estimation of biodiesel CN from its FAMEs profile. In the proposed approach, ANN paradigm was used for modeling the inner relation between the input and the output PLS score vectors. In addition, the capability of the developed method in predicting the biodiesel CN was compared with the basal PLS method. The accuracy of the developed approaches for computing the biodiesel CN was assessed using three statistical criteria, i.e., coefficient of determination (R"2), mean-squared error (MSE), and percentage error (PE). The ANN-adapted PLS method predicted the biodiesel CN with an R"2 value higher than 0.99 demonstrating the fidelity of the developed model over the classical PLS method with a markedly lower R"2 value of about 0.85. In order to facilitate the use of the proposed model, an easy-to-use computer program was also developed on the basis of ANN-adapted PLS

Development of an ANN optimized mucoadhesive buccal tablet containing flurbiprofen and lidocaine for dental pain.

Science.gov (United States)

Hussain, Amjad; Syed, Muhammad Ali; Abbas, Nasir; Hanif, Sana; Arshad, Muhammad Sohail; Bukhari, Nadeem Irfan; Hussain, Khalid; Akhlaq, Muhammad; Ahmad, Zeeshan

2016-06-01

A novel mucoadhesive buccal tablet containing flurbiprofen (FLB) and lidocaine HCl (LID) was prepared to relieve dental pain. Tablet formulations (F1-F9) were prepared using variable quantities of mucoadhesive agents, hydroxypropyl methyl cellulose (HPMC) and sodium alginate (SA). The formulations were evaluated for their physicochemical properties, mucoadhesive strength and mucoadhesion time, swellability index and in vitro release of active agents. Release of both drugs depended on the relative ratio of HPMC:SA. However, mucoadhesive strength and mucoadhesion time were better in formulations, containing higher proportions of HPMC compared to SA. An artificial neural network (ANN) approach was applied to optimise formulations based on known effective parameters (i.e., mucoadhesive strength, mucoadhesion time and drug release), which proved valuable. This study indicates that an effective buccal tablet formulation of flurbiprofen and lidocaine can be prepared via an optimized ANN approach.

EEG-Based Computer Aided Diagnosis of Autism Spectrum Disorder Using Wavelet, Entropy, and ANN

Directory of Open Access Journals (Sweden)

Ridha Djemal

2017-01-01

Full Text Available Autism spectrum disorder (ASD is a type of neurodevelopmental disorder with core impairments in the social relationships, communication, imagination, or flexibility of thought and restricted repertoire of activity and interest. In this work, a new computer aided diagnosis (CAD of autism ‎based on electroencephalography (EEG signal analysis is investigated. The proposed method is based on discrete wavelet transform (DWT, entropy (En, and artificial neural network (ANN. DWT is used to decompose EEG signals into approximation and details coefficients to obtain EEG subbands. The feature vector is constructed by computing Shannon entropy values from each EEG subband. ANN classifies the corresponding EEG signal into normal or autistic based on the extracted features. The experimental results show the effectiveness of the proposed method for assisting autism diagnosis. A receiver operating characteristic (ROC curve metric is used to quantify the performance of the proposed method. The proposed method obtained promising results tested using real dataset provided by King Abdulaziz Hospital, Jeddah, Saudi Arabia.

[Reinhold Reith. Torsten Meyer (Hrsg.) Luxus und Konsum : eine historische Annäherung] / Raimo Pullat

Index Scriptorium Estoniae

Pullat, Raimo, 1935-

2009-01-01

Arvustus: Reith, Reinhold. Torsten Meyer (Hrsg.) Luxus und Konsum : eine historische Annäherung. Cottbuser Studien zur Geschichte von Technik, Arbeit und Umwelt. hrsg. von Günter Bayerl. Bd. 21. 2003. Collegium Johann Beckmann'i kolmanda teaduskonverentsi ettekannete kogumikust

Neuropathological findings processed by artificial neural networks (ANNs) can perfectly distinguish Alzheimer's patients from controls in the Nun Study.

Science.gov (United States)

Grossi, Enzo; Buscema, Massimo P; Snowdon, David; Antuono, Piero

2007-06-21

Many reports have described that there are fewer differences in AD brain neuropathologic lesions between AD patients and control subjects aged 80 years and older, as compared with the considerable differences between younger persons with AD and controls. In fact some investigators have suggested that since neurofibrillary tangles (NFT) can be identified in the brains of non-demented elderly subjects they should be considered as a consequence of the aging process. At present, there are no universally accepted neuropathological criteria which can mathematically differentiate AD from healthy brain in the oldest old. The aim of this study is to discover the hidden and non-linear associations among AD pathognomonic brain lesions and the clinical diagnosis of AD in participants in the Nun Study through Artificial Neural Networks (ANNs) analysis The analyses were based on 26 clinically- and pathologically-confirmed AD cases and 36 controls who had normal cognitive function. The inputs used for the analyses were just NFT and neuritic plaques counts in neocortex and hippocampus, for which, despite substantial differences in mean lesions counts between AD cases and controls, there was a substantial overlap in the range of lesion counts. By taking into account the above four neuropathological features, the overall predictive capability of ANNs in sorting out AD cases from normal controls reached 100%. The corresponding accuracy obtained with Linear Discriminant Analysis was 92.30%. These results were consistently obtained in ten independent experiments. The same experiments were carried out with ANNs on a subgroup of 13 non severe AD patients and on the same 36 controls. The results obtained in terms of prediction accuracy with ANNs were exactly the same. Input relevance analysis confirmed the relative dominance of NFT in neocortex in discriminating between AD patients and controls and indicated the lesser importance played by NP in the hippocampus. The results of this study

'Transatlantic Print Culture, 1880-1940: Emerging Media, Emerging Modernisms', edited by Ann Ardis and Patrick Collier

Directory of Open Access Journals (Sweden)

Janet Floyd

2009-11-01

Full Text Available A review of 'Transatlantic Print Culture, 1880-1940: Emerging Media, Emerging Modernisms', edited by Ann Ardis and Patrick Collier (London: Palgrave Macmillan, 2008. Hardback, 259 pages, £50, ISBN 9780554269.

Symmetry breaking in spreading RAT2 fibroblasts requires the MAPK/ERK pathway scaffold RACK1 that integrates FAK, p190A-RhoGAP and ERK2 signaling

Czech Academy of Sciences Publication Activity Database

Klímová, Zuzana; Bráborec, Vojtěch; Maninová, Miloslava; Čáslavský, Josef; Weber, M. J.; Vomastek, Tomáš

2016-01-01

Roč. 1863, č. 9 (2016), s. 2189-2200 ISSN 0167-4889 R&D Projects: GA ČR GA13-06405S Institutional support: RVO:61388971 Keywords : RACK1 * ERK * FAK Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 4.521, year: 2016

History of psychosurgery at Sainte-Anne Hospital, Paris, France, through translational interactions between psychiatrists and neurosurgeons.

Science.gov (United States)

Zanello, Marc; Pallud, Johan; Baup, Nicolas; Peeters, Sophie; Turak, Baris; Krebs, Marie Odile; Oppenheim, Catherine; Gaillard, Raphael; Devaux, Bertrand

2017-09-01

Sainte-Anne Hospital is the largest psychiatric hospital in Paris. Its long and fascinating history began in the 18th century. In 1952, it was at Sainte-Anne Hospital that Jean Delay and Pierre Deniker used the first neuroleptic, chlorpromazine, to cure psychiatric patients, putting an end to the expansion of psychosurgery. The Department of Neuro-psychosurgery was created in 1941. The works of successive heads of the Neurosurgery Department at Sainte-Anne Hospital summarized the history of psychosurgery in France. Pierre Puech defined psychosurgery as the necessary cooperation between neurosurgeons and psychiatrists to treat the conditions causing psychiatric symptoms, from brain tumors to mental health disorders. He reported the results of his series of 369 cases and underlined the necessity for proper follow-up and postoperative re-education, illustrating the relative caution of French neurosurgeons concerning psychosurgery. Marcel David and his assistants tried to follow their patients closely postoperatively; this resulted in numerous publications with significant follow-up and conclusions. As early as 1955, David reported intellectual degradation 2 years after prefrontal leucotomies. Jean Talairach, a psychiatrist who eventually trained as a neurosurgeon, was the first to describe anterior capsulotomy in 1949. He operated in several hospitals outside of Paris, including the Sarthe Psychiatric Hospital and the Public Institution of Mental Health in the Lille region. He developed stereotactic surgery, notably stereo-electroencephalography, for epilepsy surgery but also to treat psychiatric patients using stereotactic lesioning with radiofrequency ablation or radioactive seeds of yttrium-90. The evolution of functional neurosurgery has been marked by the development of deep brain stimulation, in particular for obsessive-compulsive disorder, replacing the former lesional stereotactic procedures. The history of Sainte-Anne Hospital's Neurosurgery Department sheds

Interrater reliability of the Saint-Anne Dargassies Scale in assessing the neurological patterns of healthy preterm newborns

Directory of Open Access Journals (Sweden)

Carla Ismirna Santos Alves

Full Text Available Abstract Objectives: to assess the interrater reliability of the Saint-Anne Dargassies Scale in assessing neurological patterns of healthy preterm newborns. Methods: twenty preterm newborns met the inclusion criteria for participation in this prospective study. The neurologic examination was performed using the Saint-Anne Dargassies Scale, showing normal serial cranial ultrasound examination. In order to test the reliability, the study was structured as follows: group I (rater 1/physiotherapist; rater 2/neonatologist; group II (rater 3/physiotherapist; rater 4/child neurologist and the gold standard (expert and professor in pediatric neurology. Results: high interrater agreement was observed between groups I - II compared with the gold standard in assessing postural pattern (p<0.01. Regarding the assessment ofprimitive reflexes, greater agreement was observed in the evaluation of palmar grasp reflex and Moro reflex (p< 0.01 for group I compared with the gold standard. An analysis of tone demonstrated heterogeneous agreement, without compromising the reliability of the scale. The probability of equality between measurements of head circumference in the two groups, compared with the gold standard, was observed. Conclusions: the Saint-Anne Dargassies Scale demonstrated high reliability and homogeneity with significant power of reproducibility and may be capable to identify preterm newborns suspected of having neurological deficits.

A study of using smartphone to detect and identify construction workers' near-miss falls based on ANN

Science.gov (United States)

Zhang, Mingyuan; Cao, Tianzhuo; Zhao, Xuefeng

2018-03-01

As an effective fall accident preventive method, insight into near-miss falls provides an efficient solution to find out the causes of fall accidents, classify the type of near-miss falls and control the potential hazards. In this context, the paper proposes a method to detect and identify near-miss falls that occur when a worker walks in a workplace based on artificial neural network (ANN). The energy variation generated by workers who meet with near-miss falls is measured by sensors embedded in smart phone. Two experiments were designed to train the algorithm to identify various types of near-miss falls and test the recognition accuracy, respectively. At last, a test was conducted by workers wearing smart phones as they walked around a simulated construction workplace. The motion data was collected, processed and inputted to the trained ANN to detect and identify near-miss falls. Thresholds were obtained to measure the relationship between near-miss falls and fall accidents in a quantitate way. This approach, which integrates smart phone and ANN, will help detect near-miss fall events, identify hazardous elements and vulnerable workers, providing opportunities to eliminate dangerous conditions in a construction site or to alert possible victims that need to change their behavior before the occurrence of a fall accident.

Modeling Multi-Event Non-Point Source Pollution in a Data-Scarce Catchment Using ANN and Entropy Analysis

Directory of Open Access Journals (Sweden)

Lei Chen

2017-06-01

Full Text Available Event-based runoff–pollutant relationships have been the key for water quality management, but the scarcity of measured data results in poor model performance, especially for multiple rainfall events. In this study, a new framework was proposed for event-based non-point source (NPS prediction and evaluation. The artificial neural network (ANN was used to extend the runoff–pollutant relationship from complete data events to other data-scarce events. The interpolation method was then used to solve the problem of tail deviation in the simulated pollutographs. In addition, the entropy method was utilized to train the ANN for comprehensive evaluations. A case study was performed in the Three Gorges Reservoir Region, China. Results showed that the ANN performed well in the NPS simulation, especially for light rainfall events, and the phosphorus predictions were always more accurate than the nitrogen predictions under scarce data conditions. In addition, peak pollutant data scarcity had a significant impact on the model performance. Furthermore, these traditional indicators would lead to certain information loss during the model evaluation, but the entropy weighting method could provide a more accurate model evaluation. These results would be valuable for monitoring schemes and the quantitation of event-based NPS pollution, especially in data-poor catchments.

Review: Jennifer Browdy de Hernandez, Pauline Dongala, Omotayo Jolaosho and Anne Serafin (eds., African Women Writing Resistance: An Anthology of Contemporary Voices (2010 Buchbesprechung: Jennifer Browdy de Hernandez, Pauline Dongala, Omotayo Jolaosho und Anne Serafin (Hrsg., African Women Writing Resistance: An Anthology of Contemporary Voices (2010

Directory of Open Access Journals (Sweden)

Anja Oed

2011-01-01

Full Text Available Review of the edited volume: Jennifer Browdy de Hernandez, Pauline Dongala, Omotayo Jolaosho and Anne Serafin (eds., African Women Writing Resistance: An Anthology of Contemporary Voices, Oxford: Pambazuka Press, 2010, ISBN 978-0-299-23664-9, 376 pp.Besprechung des Sammelbandes: Jennifer Browdy de Hernandez, Pauline Dongala, Omotayo Jolaosho und Anne Serafin (Hrsg., African Women Writing Resistance: An Anthology of Contemporary Voices, Oxford: Pambazuka Press, 2010, ISBN 978-0-299-23664-9, 376 Seiten

Uudised : Indi-sahinad. Anne Erm ja Eero Raun on heliloojad. Imelaste lemmik on heavy metal

Index Scriptorium Estoniae

2007-01-01

Ameerika laulja Kimya Dawson 7. juulil Kilingi-Nõmmel minifestivalil "Schilling". Pianist Martti Raide esitab festivali Eesti muusika päevad 2007 suurkontserdil 16. aprillil Eero Rauna klaveripala "Tritonata", üllatusheliloojaks on ka "Jazzkaare" produtsent Anne Erm. Inglismaal Noorte Talentide Rahvuslikus Akadeemias tehtud uuringust

SA Virumaa Muuseumid Viru-Nigula pastopraadimuuseum / Fredi-Armand Tomps, Leila Pärtelpoeg, Annes Hermann

Index Scriptorium Estoniae

Tomps, Fredi-Armand, 1928

2008-01-01

12 ill.; fotod: Sven Arbet, Arvi Kriis; pastoraadimajas on renoveeritud esimesed ruumid, s.h. saal (arhitekt Fredi Tomps, sisearhitekt Leila Pärtelpoeg); sohva koopia on valminud 1990-ndate algul L. Pärtelpoja jooniste järgi Tartu kunstikooli mööbliosakonna õpilaste diplomitööna Annes Hermanni juhendamisel

The Nation behind the Diary: Anne Frank and the Holocaust of the Dutch Jews

Science.gov (United States)

Foray, Jennifer L.

2011-01-01

Since its first appearance in 1947, "The Diary of Anne Frank" has been translated into sixty-five different languages, including Welsh, Esperanto, and Faroese. Millions and perhaps even billions of readers, scattered throughout the globe and now spanning multiple generations, are familiar with the life and work of this young Jewish…

SCORHE: a novel and practical approach to video monitoring of laboratory mice housed in vivarium cage racks.

Science.gov (United States)

Salem, Ghadi H; Dennis, John U; Krynitsky, Jonathan; Garmendia-Cedillos, Marcial; Swaroop, Kanchan; Malley, James D; Pajevic, Sinisa; Abuhatzira, Liron; Bustin, Michael; Gillet, Jean-Pierre; Gottesman, Michael M; Mitchell, James B; Pohida, Thomas J

2015-03-01

The System for Continuous Observation of Rodents in Home-cage Environment (SCORHE) was developed to demonstrate the viability of compact and scalable designs for quantifying activity levels and behavior patterns for mice housed within a commercial ventilated cage rack. The SCORHE in-rack design provides day- and night-time monitoring with the consistency and convenience of the home-cage environment. The dual-video camera custom hardware design makes efficient use of space, does not require home-cage modification, and is animal-facility user-friendly. Given the system's low cost and suitability for use in existing vivariums without modification to the animal husbandry procedures or housing setup, SCORHE opens up the potential for the wider use of automated video monitoring in animal facilities. SCORHE's potential uses include day-to-day health monitoring, as well as advanced behavioral screening and ethology experiments, ranging from the assessment of the short- and long-term effects of experimental cancer treatments to the evaluation of mouse models. When used for phenotyping and animal model studies, SCORHE aims to eliminate the concerns often associated with many mouse-monitoring methods, such as circadian rhythm disruption, acclimation periods, lack of night-time measurements, and short monitoring periods. Custom software integrates two video streams to extract several mouse activity and behavior measures. Studies comparing the activity levels of ABCB5 knockout and HMGN1 overexpresser mice with their respective C57BL parental strains demonstrate SCORHE's efficacy in characterizing the activity profiles for singly- and doubly-housed mice. Another study was conducted to demonstrate the ability of SCORHE to detect a change in activity resulting from administering a sedative.

Development of an ANN optimized mucoadhesive buccal tablet containing flurbiprofen and lidocaine for dental pain

Directory of Open Access Journals (Sweden)

Hussain Amjad

2016-06-01

Full Text Available A novel mucoadhesive buccal tablet containing flurbiprofen (FLB and lidocaine HCl (LID was prepared to relieve dental pain. Tablet formulations (F1-F9 were prepared using variable quantities of mucoadhesive agents, hydroxypropyl methyl cellulose (HPMC and sodium alginate (SA. The formulations were evaluated for their physicochemical properties, mucoadhesive strength and mucoadhesion time, swellability index and in vitro release of active agents. Release of both drugs depended on the relative ratio of HPMC:SA. However, mucoadhesive strength and mucoadhesion time were better in formulations, containing higher proportions of HPMC compared to SA. An artificial neural network (ANN approach was applied to optimise formulations based on known effective parameters (i.e., mucoadhesive strength, mucoadhesion time and drug release, which proved valuable. This study indicates that an effective buccal tablet formulation of flurbiprofen and lidocaine can be prepared via an optimized ANN approach.

Proposal for the award of a contract for the supply of connection boxes for electrical racks for the LHC magnets

CERN Document Server

2004-01-01

This document concerns the award of a contract for the supply of 1670 connection boxes for two different types of electrical racks for the LHC magnets. The Finance Committee is invited to agree to the negotiation of an ex-works contract with CRAWFORD, HANSFORD & KIMBER (GB), for the supply of 1670 connection boxes for a total amount of 473 774 pounds sterling (1 080 442 Swiss francs), not subject to revision. The rate of exchange used is that stipulated in the tender.

Prediction of IRI in short and long terms for flexible pavements: ANN and GMDH methods

NARCIS (Netherlands)

Ziari, H.; Sobhani, J.; Ayoubinejad, J.; Hartmann, Timo

2015-01-01

Prediction of pavement condition is one of the most important issues in pavement management systems. In this paper, capabilities of artificial neural networks (ANNs) and group method of data handling (GMDH) methods in predicting flexible pavement conditions were analysed in three levels: in 1 year,

Tunnustati parimaid üliõpilasteadlasi / Elsa Suuster, Marit Alas, Annely Aleksejev ; küsitlenud Vilma Rauniste

Index Scriptorium Estoniae

Putku, Elsa, 1984-

2009-01-01

Vestlus üliõpilaste teadustööde riikliku konkursi kolme laureaadiga, kelle uurimistöö oli tehtud Saare maakonnas. Nendeks on Elsa Suuster ja Annely Aleksejev Eesti Maaülikoolist ning Marit Alas Tallinna Ülikoolist

CUDA-accelerated genetic feedforward-ANN training for data mining

International Nuclear Information System (INIS)

Patulea, Catalin; Peace, Robert; Green, James

2010-01-01

We present an implementation of genetic algorithm (GA) training of feedforward artificial neural networks (ANNs) targeting commodity graphics cards (GPUs). By carefully mapping the problem onto the unique GPU architecture, we achieve order-of-magnitude speedup over a conventional CPU implementation. Furthermore, we show that the speedup is consistent across a wide range of data set sizes, making this implementation ideal for large data sets. This performance boost enables the genetic algorithm to search a larger subset of the solution space, which results in more accurate pattern classification. Finally, we demonstrate this method in the context of the 2009 UC San Diego Data Mining Contest, achieving a world-class lift on a data set of 94682 e-commerce transactions.

2011 : Année internationale de la chimie

OpenAIRE

2011-01-01

Lors de la 63e assemblée générale des Nations Unies, 2011 a été proclamée année internationale de la chimie. En France, les acteurs de la chimie sont mobilisés pour promouvoir quatre objectifs : mettre l’accent sur l’importance de la chimie pour un développement durable dans tous les aspects de la vie sur la planète ; accroître chez les jeunes l’intérêt pour la chimie ; susciter l’enthousiasme pour une chimie tournée vers l’avenir ; célébrer les travaux de Marie Curie et la contribution des f...

CUDA-accelerated genetic feedforward-ANN training for data mining

Energy Technology Data Exchange (ETDEWEB)

Patulea, Catalin; Peace, Robert; Green, James, E-mail: cpatulea@sce.carleton.ca, E-mail: rpeace@sce.carleton.ca, E-mail: jrgreen@sce.carleton.ca [School of Systems and Computer Engineering, Carleton University, Ottawa, K1S 5B6 (Canada)

2010-11-01

We present an implementation of genetic algorithm (GA) training of feedforward artificial neural networks (ANNs) targeting commodity graphics cards (GPUs). By carefully mapping the problem onto the unique GPU architecture, we achieve order-of-magnitude speedup over a conventional CPU implementation. Furthermore, we show that the speedup is consistent across a wide range of data set sizes, making this implementation ideal for large data sets. This performance boost enables the genetic algorithm to search a larger subset of the solution space, which results in more accurate pattern classification. Finally, we demonstrate this method in the context of the 2009 UC San Diego Data Mining Contest, achieving a world-class lift on a data set of 94682 e-commerce transactions.

FPGA implementation of adaptive ANN controller for speed regulation of permanent magnet stepper motor drives

Energy Technology Data Exchange (ETDEWEB)

Hasanien, Hany M., E-mail: Hanyhasanien@ieee.or [Dept. of Elec. Power and Machines, Faculty of Eng., Ain Shams Univ., Cairo (Egypt)

2011-02-15

This paper presents a novel adaptive artificial neural network (ANN) controller, which applies on permanent magnet stepper motor (PMSM) for regulating its speed. The dynamic response of the PMSM with the proposed controller is studied during the starting process under the full load torque and under load disturbance. The effectiveness of the proposed adaptive ANN controller is then compared with that of the conventional PI controller. The proposed methodology solves the problem of nonlinearities and load changes of PMSM drives. The proposed controller ensures fast and accurate dynamic response with an excellent steady state performance. Matlab/Simulink tool is used for this dynamic simulation study. The main contribution of this work is the implementation of the proposed controller on field programmable gate array (FPGA) hardware to drive the stepper motor. The driver is built on FPGA Spartan-3E Starter from Xilinx. Experimental results are presented to demonstrate the validity and effectiveness of the proposed control scheme.

ANN based controller for three phase four leg shunt active filter for power quality improvement

Directory of Open Access Journals (Sweden)

J. Jayachandran

2016-03-01

Full Text Available In this paper, an artificial neural network (ANN based one cycle control (OCC strategy is proposed for the DSTATCOM shunted across the load in three phase four wire distribution system. The proposed control strategy mitigates harmonic/reactive currents, ensures balanced and sinusoidal source current from the supply mains that are nearly in phase with the supply voltage and compensates neutral current under varying source and load conditions. The proposed control strategy is superior over conventional methods as it eliminates, the sensors needed for sensing load current and coupling inductor current, in addition to the multipliers and the calculation of reference currents. ANN controllers are implemented to maintain voltage across the capacitor and as a compensator to compensate neutral current. The DSTATCOM performance is validated for all possible conditions of source and load by simulation using MATLAB software and simulation results prove the efficacy of the proposed control over conventional control strategy.

FPGA implementation of adaptive ANN controller for speed regulation of permanent magnet stepper motor drives

International Nuclear Information System (INIS)

Hasanien, Hany M.

2011-01-01

This paper presents a novel adaptive artificial neural network (ANN) controller, which applies on permanent magnet stepper motor (PMSM) for regulating its speed. The dynamic response of the PMSM with the proposed controller is studied during the starting process under the full load torque and under load disturbance. The effectiveness of the proposed adaptive ANN controller is then compared with that of the conventional PI controller. The proposed methodology solves the problem of nonlinearities and load changes of PMSM drives. The proposed controller ensures fast and accurate dynamic response with an excellent steady state performance. Matlab/Simulink tool is used for this dynamic simulation study. The main contribution of this work is the implementation of the proposed controller on field programmable gate array (FPGA) hardware to drive the stepper motor. The driver is built on FPGA Spartan-3E Starter from Xilinx. Experimental results are presented to demonstrate the validity and effectiveness of the proposed control scheme.

Development of wavelet-ANN models to predict water quality parameters in Hilo Bay, Pacific Ocean.

Science.gov (United States)

Alizadeh, Mohamad Javad; Kavianpour, Mohamad Reza

2015-09-15

The main objective of this study is to apply artificial neural network (ANN) and wavelet-neural network (WNN) models for predicting a variety of ocean water quality parameters. In this regard, several water quality parameters in Hilo Bay, Pacific Ocean, are taken under consideration. Different combinations of water quality parameters are applied as input variables to predict daily values of salinity, temperature and DO as well as hourly values of DO. The results demonstrate that the WNN models are superior to the ANN models. Also, the hourly models developed for DO prediction outperform the daily models of DO. For the daily models, the most accurate model has R equal to 0.96, while for the hourly model it reaches up to 0.98. Overall, the results show the ability of the model to monitor the ocean parameters, in condition with missing data, or when regular measurement and monitoring are impossible. Copyright © 2015 Elsevier Ltd. All rights reserved.

Facteurs prédictifs de succès des étudiants en première année de médecine à l'université de Parakou

Science.gov (United States)

Adoukonou, Thierry; Tognon-Tchegnonsi, Francis; Mensah, Emile; Allodé, Alexandre; Adovoekpe, Jean-Marie; Gandaho, Prosper; Akpona, Simon

2016-01-01

Introduction Plusieurs facteurs dont les notes obtenues au BAC peuvent influencer les performances académiques des étudiants en première année de médecine. L'objectif de cette étude était d’évaluer la relation entre les résultats des étudiants au BAC et le succès en première année de médecine. Méthodes Nous avons réalisé une étude analytique ayant inclus l'ensemble des étudiants régulièrement inscrits en première année à la Faculté de Médecine de l'université de Parakou durant l'année académique 2010-2011. Les données concernant les notes par discipline et mention obtenue au BAC ont été collectées. Une analyse multivariée utilisant la régression logistique et la régression linéaire multiple a permis d’établir les meilleurs prédicteurs du succès et de la moyenne de l’étudiant en fin d'année. Le logiciel SPSS version 17.0 a été utilisé pour l'analyse des données et un p 15/20 était associée au succès (OR: 2,8 [1,32- 6,00]). Pour la moyenne générale obtenue en fin d'année seule une mention bien obtenue au BAC était associée (coefficient de l'erreur standard: 0,130 Bêta =0,370 et p=0,00001). Conclusion Les meilleurs prédicateurs du succès en première année étaient une bonne moyenne en sciences physiques au BAC et une mention bien. La prise en compte de ces éléments dans le recrutement des étudiants en première année pourrait améliorer les résultats académiques. PMID:27313819

Neuropathological findings processed by artificial neural networks (ANNs can perfectly distinguish Alzheimer's patients from controls in the Nun Study

Directory of Open Access Journals (Sweden)

Snowdon David

2007-06-01

Full Text Available Abstract Background Many reports have described that there are fewer differences in AD brain neuropathologic lesions between AD patients and control subjects aged 80 years and older, as compared with the considerable differences between younger persons with AD and controls. In fact some investigators have suggested that since neurofibrillary tangles (NFT can be identified in the brains of non-demented elderly subjects they should be considered as a consequence of the aging process. At present, there are no universally accepted neuropathological criteria which can mathematically differentiate AD from healthy brain in the oldest old. The aim of this study is to discover the hidden and non-linear associations among AD pathognomonic brain lesions and the clinical diagnosis of AD in participants in the Nun Study through Artificial Neural Networks (ANNs analysis Methods The analyses were based on 26 clinically- and pathologically-confirmed AD cases and 36 controls who had normal cognitive function. The inputs used for the analyses were just NFT and neuritic plaques counts in neocortex and hippocampus, for which, despite substantial differences in mean lesions counts between AD cases and controls, there was a substantial overlap in the range of lesion counts. Results By taking into account the above four neuropathological features, the overall predictive capability of ANNs in sorting out AD cases from normal controls reached 100%. The corresponding accuracy obtained with Linear Discriminant Analysis was 92.30%. These results were consistently obtained in ten independent experiments. The same experiments were carried out with ANNs on a subgroup of 13 non severe AD patients and on the same 36 controls. The results obtained in terms of prediction accuracy with ANNs were exactly the same. Input relevance analysis confirmed the relative dominance of NFT in neocortex in discriminating between AD patients and controls and indicated the lesser importance

[Sciatica. From stretch rack to microdiscectomy].

Science.gov (United States)

Gruber, P; Böni, T

2015-12-01

In ancient times as well as in the Middle Ages treatment options for discogenic nerve compression syndrome were limited and usually not very specific because of low anatomical and pathophysiological knowledge. The stretch rack (scamnum Hippocratis) was particularly prominent but was widely used as a therapeutic device for very different spinal disorders. Since the beginning of the nineteenth century anatomical knowledge increased and the advances in the fields of asepsis, anesthesia and surgery resulted in an increase in surgical interventions on the spine. In 1908 the first successful lumbar discectomy was initiated and performed by the German neurologist Heinrich O. Oppenheim (1858-1919) and the surgeon Fedor Krause (1857-1937); however, neither recognized the true pathological condition of discogenic nerve compression syndrome. With the landmark report in the New England Journal of Medicine in 1934, the two American surgeons William Jason Mixter (1880-1958) and Joseph Seaton Barr (1901-1963) finally clarified the pathomechanism of lumbar disc herniation and furthermore, propagated discectomy as the standard therapy. Since then interventions on intervertebral discs rapidly increased and the treatment options for lumbar disc surgery quickly evolved. The surgical procedures changed over time and were continuously being refined. In the late 1960s the surgical microscope was introduced for spinal surgery by the work of the famous neurosurgeon Mahmut Gazi Yasargil and his colleague Wolfhard Caspar and so-called microdiscectomy was introduced. Besides open discectomy other interventional techniques were developed to overcome the side effects of surgical procedures. In 1964 the American orthopedic surgeon Lyman Smith (1912-1991) introduced chemonucleolysis, a minimally invasive technique consisting only of a cannula and the proteolytic enzyme chymopapain, which is injected into the disc compartment to dissolve the displaced disc material. In 1975 the Japanese orthopedic

Kuis saada läbi Siirita? / Mari-Ann Kelam, Erika Salumäe, Sirje Endre

Index Scriptorium Estoniae

Kelam, Mari-Ann, 1946-

2001-01-01

Riigikogu uude juhatusse ei kuulu ühtegi naist : Keskerakond valis Siiri Oviiri asemele Riigikogu aseesimehe kohale Peeter Kreitzbergi. Naiste osalemisvõimalust poliitikas kommenteerivad Riigikogu naisliikmed Mari-Ann Kelam, Erika Salumäe, Sirje Endre, Jaana Padrik, Viive Rosenberg, Mai Treial, Ivi Eenmaa, Liis Klaar, Liia Hänni, Laine Tarvis

75 FR 23745 - Jo-Ann Stores, Inc., Provisional Acceptance of a Settlement Agreement and Order

Science.gov (United States)

2010-05-04

... Acceptance of a Settlement Agreement and Order AGENCY: Consumer Product Safety Commission. ACTION: Notice... under the laws of the State of Ohio, with its principal offices located in Hudson, Ohio. At all times relevant hereto, Jo-Ann imported, offered for sale and sold various children's products. Staff Allegations...