Effects of a potential drop of a shipping cask, a waste container, and a bare fuel assembly during waste-handling operations

International Nuclear Information System (INIS)

Wu, C.L.; Lee, J.; Lu, D.L.; Jardine, L.J.

1991-12-01

This study investigates the effects of potential drops of a typical shipping cask, waste container, and bare fuel assembly during waste-handling operations at the prospective Yucca Mountain Repository. The waste-handling process (one stage, no consolidation configuration) is examined to estimate the maximum loads imposed on typical casks and containers as they are handled by various pieces of equipment during waste-handling operations. Maximum potential drop heights for casks and containers are also evaluated for different operations. A nonlinear finite-element model is employed to represent a hybrid spent fuel container subject to drop heights of up to 30 ft onto a reinforced concrete floor. The impact stress, strain, and deformation are calculated, and compared to the failure criteria to estimate the limiting (maximum permissible) drop height for the waste container. A typical Westinghouse 17 x 17 PWR fuel assembly is analyzed by a simplified model to estimate the energy absorption by various parts of the fuel assembly during a 30 ft drop, and to determine the amount of kinetic energy in a fuel pin at impact. A nonlinear finite-element analysis of an individual fuel pin is also performed to estimate the amount of fuel pellet fracture due to impact. This work was completed on May 1990

Non-fuel assembly components: 10 CFR 61.55 classification for waste disposal

International Nuclear Information System (INIS)

Migliore, R.J.; Reid, B.D.; Fadeff, S.K.; Pauley, K.A.; Jenquin, U.P.

1994-09-01

This document reports the results of laboratory radionuclide measurements on a representative group of non-fuel assembly (NFA) components for the purposes of waste classification. This document also provides a methodology to estimate the radionuclide inventory of NFA components, including those located outside the fueled region of a nuclear reactor. These radionuclide estimates can then be used to determine the waste classification of NFA components for which there are no physical measurements. Previously, few radionuclide inventory measurements had been performed on NFA components. For this project, recommended scaling factors were selected for the ORIGEN2 computer code that result in conservative estimates of radionuclide concentrations in NFA components. These scaling factors were based upon experimental data obtained from the following NFA components: (1) a pressurized water reactor (PWR) burnable poison rod assembly, (2) a PVM rod cluster control assembly, and (3) a boiling water reactor cruciform control rod blade. As a whole, these components were found to be within Class C limits. Laboratory radionuclide measurements for these components are provided in detail

Multi-recycling of transuranic elements in a PWR assembly with reduced fuel rod diameter

International Nuclear Information System (INIS)

Chambers, Alex; Ragusa, Jean C.

2014-01-01

Highlights: • Study of multiple recycling passes of transuranic elements: (a) without exceeding 5 wt.% on U-235 enrichment; (b) using PWR fuel assemblies compatible with current reactor core internals. • Isotopic concentrations tend towards an equilibrium after 15 recycle passes, suggesting that thermal recycling may be continued beyond that point. • Radiotoxicity comparisons for once-through UOX, once-recycle MOX-Pu, and multiple recycle passes of MOX-PuNpAm and MOX-PuNpAmCm are presented. - Abstract: This paper examines the multi-recycling of transuranic (TRU) elements (Pu-Np-Am-Cm) in standard Pressurized Water Reactor (PWR) assemblies. The original feed of TRU comes from legacy spent UOX fuel. For all subsequent recycling passes, TRU elements from the previous generation are employed, supplemented by TRU from legacy UOX fuel, as needed. The design criteria include: 235 U enrichment requirements to remain below 5 w/o, TRU loading limits to avoid return to criticality under voided conditions, and assembly power peaking factors. In order to carry out multiple recycling passes within the design envelope, additional neutron moderation is required and achieved by reducing the fuel pellet diameter by about 13%, thus keeping the assembly design compatible with current PWR core internals. TRU transmutation rates and long-term ingestion radiotoxicity results are presented for 15 recycling passes and compared to standard UOX and MOX once-through cycles. The results also show that TRU fuel isotopics and radiotoxicity tend towards an equilibrium, enabling further additional recycling passes

RCC-C: Design and construction rules for fuel assemblies of PWR nuclear power plants

International Nuclear Information System (INIS)

2015-01-01

The RCC-C code contains all the requirements for the design, fabrication and inspection of nuclear fuel assemblies and the different types of core components (rod cluster control assemblies, burnable poison rod assemblies, primary and secondary source assemblies and thimble plug assemblies). The design, fabrication and inspection rules defined in RCC-C leverage the results of the research and development work pioneered in France, Europe and worldwide, and which have been successfully used by industry to design and build nuclear fuel assemblies and incorporate the resulting feedback. The code's scope covers: fuel system design, especially for assemblies, the fuel rod and associated core components, the characteristics to be checked for products and parts, fabrication methods and associated inspection methods. The RCC-C code is used by the operator of the PWR nuclear power plants in France as a reference when sourcing fuel from the world's top two suppliers in the PWR market, given that the French operator is the world's largest buyer of PWR fuel. Fuel for EPR projects is manufactured according to the provisions of the RCC-C code. The code is available in French and English. The 2005 edition has been translated into Chinese. Contents of the 2015 edition of the RCC-C code: Chapter 1 - General provisions: 1.1 Purpose of the RCC-C, 1.2 Definitions, 1.3 Applicable standards, 1.4 Equipment subject to the RCC-C, 1.5 Management system, 1.6 Processing of non-conformances; Chapter 2 - Description of the equipment subject to the RCC-C: 2.1 Fuel assembly, 2.2 Core components; Chapter 3 - Design: Safety functions, operating functions and environment of fuel assemblies and core components, design and safety principles; Chapter 4 - Manufacturing: 4.1 Materials and part characteristics, 4.2 Assembly requirements, 4.3 Manufacturing and inspection processes, 4.4 Inspection methods, 4.5 Certification of NDT inspectors, 4.6 Characteristics to be inspected for the

Optimization of PWR fuel assembly radial enrichment and burnable poison location based on adaptive simulated annealing

International Nuclear Information System (INIS)

Rogers, Timothy; Ragusa, Jean; Schultz, Stephen; St Clair, Robert

2009-01-01

The focus of this paper is to present a concurrent optimization scheme for the radial pin enrichment and burnable poison location in PWR fuel assemblies. The methodology is based on the Adaptive Simulated Annealing (ASA) technique, coupled with a neutron lattice physics code to update the cost function values. In this work, the variations in the pin U-235 enrichment are variables to be optimized radially, i.e., pin by pin. We consider the optimization of two categories of fuel assemblies, with and without Gadolinium burnable poison pins. When burnable poisons are present, both the radial distribution of enrichment and the poison locations are variables in the optimization process. Results for 15 x 15 PWR fuel assembly designs are provided.

Gamma and Neutron Radiolysis in the 21-PWR Waste Package

Energy Technology Data Exchange (ETDEWEB)

J.S. Tang

2001-05-03

The objective of this calculation is to compute gamma and neutron dose rates in order to determine the maximum radiolytic production of nitric acid and other chemical species inside the 21-PWR (pressurized-water reactor) waste package (WP). The scope of this calculation is limited to the time period between 5,000 and 100,000 years after emplacement. The information provided by the sketches attached to this calculation is that of the potential design for the type of WP considered in this calculation. The results of this calculation will be used to evaluate nitric acid corrosion of fuel cladding from radiolysis in the 21-PWR WP. This calculation was performed in accordance with the Technical Work Plan for: Waste Package Design Description for LA (Civilian Radioactive Waste Management System (CRWMS) Management and Operating Contractor (M&O) 2000a). AP-3.124, Calculations, is used to perform the calculation and develop the document. This calculation is associated with the total system performance assessment (TSPA) of which the spent fuel cladding integrity is to be evaluated.

Gamma and Neutron Radiolysis in the 21-PWR Waste Package

International Nuclear Information System (INIS)

J.S. Tang

2001-01-01

The objective of this calculation is to compute gamma and neutron dose rates in order to determine the maximum radiolytic production of nitric acid and other chemical species inside the 21-PWR (pressurized-water reactor) waste package (WP). The scope of this calculation is limited to the time period between 5,000 and 100,000 years after emplacement. The information provided by the sketches attached to this calculation is that of the potential design for the type of WP considered in this calculation. The results of this calculation will be used to evaluate nitric acid corrosion of fuel cladding from radiolysis in the 21-PWR WP. This calculation was performed in accordance with the Technical Work Plan for: Waste Package Design Description for LA (Civilian Radioactive Waste Management System (CRWMS) Management and Operating Contractor (M and O) 2000a). AP-3.124, Calculations, is used to perform the calculation and develop the document. This calculation is associated with the total system performance assessment (TSPA) of which the spent fuel cladding integrity is to be evaluated

Radionuclide compositions of spent fuel and high level waste for the uranium and plutonium fuelled PWR

International Nuclear Information System (INIS)

Fairclough, M.P.; Tymons, B.J.

1985-06-01

The activities of a selection of radionuclides are presented for three types of reactor fuel of interest in radioactive waste management. The fuel types are for a uranium 'burning' PWR, a plutonium 'burning' PWR using plutonium recycled from spent uranium fuel and a plutonium 'burning' PWR using plutonium which has undergone multiple recycle. (author)

Multi-recycling of transuranic elements in a PWR assembly with reduced fuel rod diameter

Energy Technology Data Exchange (ETDEWEB)

Chambers, Alex, E-mail: acchamb@gmail.com; Ragusa, Jean C., E-mail: jean.ragusa@tamu.edu

2014-04-01

Highlights: • Study of multiple recycling passes of transuranic elements: (a) without exceeding 5 wt.% on U-235 enrichment; (b) using PWR fuel assemblies compatible with current reactor core internals. • Isotopic concentrations tend towards an equilibrium after 15 recycle passes, suggesting that thermal recycling may be continued beyond that point. • Radiotoxicity comparisons for once-through UOX, once-recycle MOX-Pu, and multiple recycle passes of MOX-PuNpAm and MOX-PuNpAmCm are presented. - Abstract: This paper examines the multi-recycling of transuranic (TRU) elements (Pu-Np-Am-Cm) in standard Pressurized Water Reactor (PWR) assemblies. The original feed of TRU comes from legacy spent UOX fuel. For all subsequent recycling passes, TRU elements from the previous generation are employed, supplemented by TRU from legacy UOX fuel, as needed. The design criteria include: {sup 235}U enrichment requirements to remain below 5 w/o, TRU loading limits to avoid return to criticality under voided conditions, and assembly power peaking factors. In order to carry out multiple recycling passes within the design envelope, additional neutron moderation is required and achieved by reducing the fuel pellet diameter by about 13%, thus keeping the assembly design compatible with current PWR core internals. TRU transmutation rates and long-term ingestion radiotoxicity results are presented for 15 recycling passes and compared to standard UOX and MOX once-through cycles. The results also show that TRU fuel isotopics and radiotoxicity tend towards an equilibrium, enabling further additional recycling passes.

Seismic behaviour of PWR fuel assemblies model and its validation

International Nuclear Information System (INIS)

Queval, J.C.; Gantenbein, F.; Brochard, D.; Benjedidia, A.

1991-01-01

The validity of the models simulating the seismic behaviour of PWR cores can only be exactly demonstrated by seismic testing on groups of fuel assemblies. Shake table seismic tests of rows of assembly mock-ups, conducted by the CEA in conjunction with FRAMATOME, are presented in reference /1/. This paper addresses the initial comparisons between model and test results for a row of five assemblies in air. Two models are used: a model with a single beam per assembly, used regularly in accident analyses, and described in reference /2/, and a more refined 2-beam per assembly model, geared mainly towards interpretation of test results. The 2-beam model is discussed first, together with parametric studies used to characterize it, and the study of the assembly row for a period limited to 2 seconds and for different excitation levels. For the 1-beam model assembly used in applications, the row is studied over the total test time, i.e twenty seconds, which covers the average duration of the core seismic behaviour studies, and for a peak exciting acceleration value at 0.4 g, which corresponds to the SSE level of the reference spectrum

Study on new-type fuel-related assembly handling tools for PWR NPP

International Nuclear Information System (INIS)

Fan Xiumei

2013-01-01

This article describes the design and study on a set of new-type fuel-related assembly snatching tools used for PWR NPP. The purpose is mainly to enhance the tool safety, reliability and convenientness by improvement of the mechanism and structure of the tool for snatching preciseness and avoiding from falling and abrasion of fuel-related assemblies for any condition. The new-type fuel-related assembly handling tools are compared with similar equipment in worldwide in terms of function, main technical characteristic, and safety and protection, some of them are better than the similar equipment in that they have reliable loading and unloading and conveying capabilities. (author)

Liquid radioactive waste processing improvement of PWR nuclear power plants

International Nuclear Information System (INIS)

Nery, Renata Wolter dos Reis; Martinez, Aquilino Senra; Monteiro, Jose Luiz Fontes

2005-01-01

The study evaluate an inorganic ion exchange to process the low level liquid radwaste of PWR nuclear plants, so that the level of the radioactivity in the effluents and the solid waste produced during the treatment of these liquid radwaste can be reduced. The work compares two types of ion exchange materials, a strong acid cation exchange resin, that is the material typically used to remove radionuclides from PWR nuclear plants wastes, and a mordenite zeolite. These exchange material were used to remove cesium from a synthetic effluent containing only this ion and another effluent containing cesium and cobalt. The breakthrough curves of the zeolite and resin using a fix bed reactor were compared. The results demonstrated that the zeolite is more efficient than the resin in removing cesium from a solution containing cesium and cobalt. The results also showed that a bed combining zeolite and resin can process more volume of an effluent containing cesium and cobalt than a bed resin alone. (author)

The verification of PWR-fuel code for PWR in-core fuel management

International Nuclear Information System (INIS)

Surian Pinem; Tagor M Sembiring; Tukiran

2015-01-01

In-core fuel management for PWR is not easy because of the number of fuel assemblies in the core as much as 192 assemblies so many possibilities for placement of the fuel in the core. Configuration of fuel assemblies in the core must be precise and accurate so that the reactor operates safely and economically. It is necessary for verification of PWR-FUEL code that will be used in-core fuel management for PWR. PWR-FUEL code based on neutron transport theory and solved with the approach of multi-dimensional nodal diffusion method many groups and diffusion finite difference method (FDM). The goal is to check whether the program works fine, especially for the design and in-core fuel management for PWR. Verification is done with equilibrium core search model at three conditions that boron free, 1000 ppm boron concentration and critical boron concentration. The result of the average burn up fuel assemblies distribution and power distribution at BOC and EOC showed a consistent trend where the fuel with high power at BOC will produce a high burn up in the EOC. On the core without boron is obtained a high multiplication factor because absence of boron in the core and the effect of fission products on the core around 3.8 %. Reactivity effect at 1000 ppm boron solution of BOC and EOC is 6.44 % and 1.703 % respectively. Distribution neutron flux and power density using NODAL and FDM methods have the same result. The results show that the verification PWR-FUEL code work properly, especially for core design and in-core fuel management for PWR. (author)

An immersed body method for coupled neutron transport and thermal hydraulic simulations of PWR assemblies

International Nuclear Information System (INIS)

Jewer, S.; Buchan, A.G.; Pain, C.C.; Cacuci, D.G.

2014-01-01

Highlights: • A new method of coupled radiation transport, heat and momentum exchanges on fluids, and heat transfer simulations. • Simulation of the thermal hydraulics and radiative properties within whole PWR assemblies. • An immersed body method for modelling complex solid domains on practical computational meshes. - Abstract: A recently developed immersed body method is adapted and used to model a typical pressurised water reactor (PWR) fuel assembly. The approach is implemented with the numerical framework of the finite element, transient criticality code, FETCH which is composed of the neutron transport code, EVENT, and the CFD code, FLUIDITY. Within this framework the neutron transport equation, Navier–Stokes equations and a fluid energy conservation equation are solved in a coupled manner on a coincident structured or unstructured mesh. The immersed body method has been used to model the solid fuel pins. The key feature of this method is that the fluid/neutronic domain and the solid domain are represented by overlapping and non-conforming meshes. The main difficulty of this approach, for which a solution is proposed in this work, is the conservative mapping of the energy and momentum exchange between the fluid/neutronic mesh and the solid fuel pin mesh. Three numerical examples are presented which include a validation of the fuel pin submodel against an analytical solution; an uncoupled (no neutron transport solution) PWR fuel assembly model with a specified power distribution which was validated against the COBRA-EN subchannel analysis code; and finally a coupled model of a PWR fuel assembly with reflective neutron boundary conditions. Coupling between the fluid and neutron transport solutions is through the nuclear cross sections dependence on Doppler fuel temperature, coolant density and temperature, which was taken into account by using pre-calculated cross-section lookup tables generated using WIMS9a. The method was found to show good agreement

Modification of the ANC Nodal Code for analysis of PWR assembly bow

International Nuclear Information System (INIS)

Franceschini, Fausto; Fetterman, Robert J.; Little, David C.

2008-01-01

Refueling operations at certain PWR cores have revealed fuel assemblies with assembly bow that was higher than expected. As the fuel assemblies bow, the gaps between assemblies change from the uniform nominal configuration. This causes a change in the water volume which affects neutron moderation and thereby power distribution, fuel depletion history, rod internal pressure, etc., with non-trivial impacts on the safety analysis. Westinghouse has developed a new methodology for incorporation of assembly bow in its reload safety analysis package. As part of the new process, the standard Westinghouse reactor physics tool for core analysis, the Advanced Nodal Code ANC, has been modified. The modified ANC, ANCGAP, enables explicit treatment of three-dimensional gap distributions in its neutronic calculations; its accuracy is similar to that of the standard ANC, as demonstrated through an extensive benchmark campaign conducted over a variety of fuel compositions and challenging gap configurations. These features make ANCGAP a crucial tool in the Westinghouse assembly bow package. (authors)

Modification of the ANC Nodal Code for analysis of PWR assembly bow

Energy Technology Data Exchange (ETDEWEB)

Franceschini, Fausto; Fetterman, Robert J.; Little, David C. [Westinghouse Electric Company LLC, Pittsburgh PA (United States)

2008-07-01

Refueling operations at certain PWR cores have revealed fuel assemblies with assembly bow that was higher than expected. As the fuel assemblies bow, the gaps between assemblies change from the uniform nominal configuration. This causes a change in the water volume which affects neutron moderation and thereby power distribution, fuel depletion history, rod internal pressure, etc., with non-trivial impacts on the safety analysis. Westinghouse has developed a new methodology for incorporation of assembly bow in its reload safety analysis package. As part of the new process, the standard Westinghouse reactor physics tool for core analysis, the Advanced Nodal Code ANC, has been modified. The modified ANC, ANCGAP, enables explicit treatment of three-dimensional gap distributions in its neutronic calculations; its accuracy is similar to that of the standard ANC, as demonstrated through an extensive benchmark campaign conducted over a variety of fuel compositions and challenging gap configurations. These features make ANCGAP a crucial tool in the Westinghouse assembly bow package. (authors)

A Hold-down Margin Assessment using Statistical Method for the PWR Fuel Assembly

International Nuclear Information System (INIS)

Jeon, S. Y.; Park, N. K.; Lee, K. S.; Kim, H. K.

2007-01-01

The hold-down springs provide an acceptable hold down force against hydraulic uplift force absorbing the length change of the fuel assembly relative to the space between the upper and lower core plates in PWR. These length changes are mainly due to the thermal expansion, irradiation growth and creep down of the fuel assemblies. There are two kinds of hold-down springs depending on the different design concept of the reactor internals of the PWR in Korea, one is a leaf-type hold down spring for Westinghouse type plants and the other is a coil-type hold-down spring for OPR1000 (Optimized Power Reactor 1000). There are four sets of hold-down springs in each fuel assembly for leaf type hold-down spring and each set of the hold-down springs consists of multiple tapered leaves to form a cantilever leaf spring set. The length, width and thickness of the spring leaves are selected to provide the desired spring constant, deflection range, and hold down force. There are four coil springs in each fuel assembly for coil-type hold-down spring. In this study, the hold-down forces and margins were calculated for the leaf-type and coil-type hold-down springs considering geometrical data of the fuel assembly and its components, length changes of the fuel assembly due to thermal expansion, irradiation growth, creep, and irradiation relaxation. The hold-down spring forces were calculated deterministically and statistically to investigate the benefit of the statistical calculation method in view of hold-down margin. The Monte-Carlo simulation method was used for the statistical hold down force calculation

Assessment of management alternatives for LWR wastes. Volume 4. Description of a Belgian scenario for PWR waste

International Nuclear Information System (INIS)

Crustin, J.; Glibert, R.

1993-01-01

This report deals with the description of a management route for PWR waste relying to a certain extent on Belgian practices in this particular area. This description, which aims at providing input data for subsequent cost evaluation, includes all management steps which are usually implemented for solid, liquid and gaseous wastes from their production up to the interim storage of the final waste products. This study is part of an overall theoretical exercise aimed at evaluating a selection of management routes for LWR waste based on economical and radiological criteria

Assessment of management alternatives for LWR wastes. Volume 2. Description of a French scenario for PWR waste

International Nuclear Information System (INIS)

Saulieu, E. de; Chary, C.

1993-01-01

This report deals with the description of a management route for PWR waste relying to a certain extent on French practices in this particular area. This description, which aims at providing input data for subsequent cost evaluation, includes all management steps which are usually implemented for solid, liquid and gaseous wastes from their production up to the interim storage of the final waste products. This study is part of an overall theoretical exercise aimed at evaluating a selection of management routes for LWR waste based on economical and radiological criteria

Fuel assembly for pressure loss variable PWR type reactor

International Nuclear Information System (INIS)

Yoshikuni, Masaaki.

1993-01-01

In a PWR type reactor, a pressure loss control plate is attached detachably to a securing screw holes on the lower surface of a lower nozzle to reduce a water channel cross section and increase a pressure loss. If a fuel assembly attached with the pressure loss control plate is disposed at a periphery of the reactor core where the power is low and heat removal causes no significant problem, a flowrate at the periphery of the reactor core is reduced. Since this flowrate is utilized for removal of heat from fuel assemblies of high powder at the center of the reactor core where a pressure loss control plate is not attached, a thermal limit margin of the whole reactor core is increased. Thus, a limit of power peaking can be moderated, to obtain a fuel loading pattern improved with neutron economy. (N.H.)

Radiological characterization of spent control rod assemblies

International Nuclear Information System (INIS)

Lepel, E.A.; Robertson, D.E.; Thomas, C.W.; Pratt, S.L.; Haggard, D.L.

1995-10-01

This document represents the final report of an ongoing study to provide radiological characterizations, classifications, and assessments in support of the decommissioning of nuclear power stations. This report describes the results of non-destructive and laboratory radionuclide measurements, as well as waste classification assessments, of BWR and PWR spent control rod assemblies. The radionuclide inventories of these spent control rods were determined by three separate methodologies, including (1) direct assay techniques, (2) calculational techniques, and (3) by sampling and laboratory radiochemical analyses. For the BWR control rod blade (CRB) and PWR burnable poison rod assembly (BPRA), 60 Co and 63 Ni, present in the stainless steel cladding, were the most abundant neutron activation products. The most abundant radionuclide in the PWR rod cluster control assembly (RCCA) was 108m Ag (130 yr halflife) produced in the Ag-In-Cd alloy used as the neutron poison. This radionuclide will be the dominant contributor to the gamma dose rate for many hundreds of years. The results of the direct assay methods agree very well (±10%) with the sampling/radiochemical measurements. The results of the calculational methods agreed fairly well with the empirical measurements for the BPRA, but often varied by a factor of 5 to 10 for the CRB and the RCCA assemblies. If concentration averaging and encapsulation, as allowed by 10CFR61.55, is performed, then each of the entire control assemblies would be classified as Class C low-level radioactive waste

Thermal Response of the 21-PWR Waste Package to a Fire Accident

International Nuclear Information System (INIS)

F.P. Faucher; H. Marr; M.J. Anderson

2000-01-01

The objective of this calculation is to evaluate the thermal response of the 21-PWR WP (pressurized water reactor waste package) to the regulatory fire event. The scope of this calculation is limited to the two-dimensional waste package temperature calculations to support the waste package design. The information provided by the sketches attached to this calculation (Attachment IV) is that of the potential design of the type of waste package considered in this calculation. The procedure AP-3.12Q.Calculations (Reference 1), and the Development Plan (Reference 24) are used to develop this calculation

Low-density moderation in the storage of PWR fuel assemblies

International Nuclear Information System (INIS)

Alcorn, F.M.

1987-01-01

The nuclear criticality safety of PWR fuel storage arrays requires that the potential of low-density moderation within the array be considered. The calculated criticality effect of low-density moderation in a typical PWR fuel assembly array is described in this paper. Calculated reactivity due to low-density moderation can vary significantly between physics codes that have been validated for well moderated systems. The availability of appropriate benchmark experiments for low-density moderation is quite limited; attempts to validate against the one set of suitable experiments at low density have been disappointing. Calculations indicate that a typical array may be unacceptable should the array be subjected to interstitial moderation equivalent to 5 % of full density water. Array parameters (such as spacing and size) will dramatically affect the calculated maximum K-eff at low-density moderation. Administrative and engineered control may be necessary to assure maintenance of safety at low-density moderation. Potential sources for low-density moderation are discussed; in general, accidentally achieving degrees of low-density moderation which might lead to a compromise of safety are not credible. (author)

Lateral hydraulic forces calculation on PWR fuel assemblies with computational fluid dynamics codes

International Nuclear Information System (INIS)

Corpa Masa, R.; Jimenez Varas, G.; Moreno Garcia, B.

2016-01-01

To be able to simulate the behavior of nuclear fuel under operating conditions, it is required to include all the representative loads, including the lateral hydraulic forces which were not included traditionally because of the difficulty of calculating them in a reliable way. Thanks to the advance in CFD codes, now it is possible to assess them. This study calculates the local lateral hydraulic forces, caused by the contraction and expansion of the flow due to the bow of the surrounding fuel assemblies, on of fuel assembly under typical operating conditions from a three loop Westinghouse PWR reactor. (Author)

Liquid radioactive waste processing improvement of PWR nuclear power plants; Melhorias no processamento de rejeitos liquidos radioativos de usinas nucleares PWR

Energy Technology Data Exchange (ETDEWEB)

Nery, Renata Wolter dos Reis; Martinez, Aquilino Senra; Monteiro, Jose Luiz Fontes [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia. Programa de Engenharia Nuclear]. E-mail: wolter@eletronuclear.gov.br; monteiro@peq.coppe.ufrj.br; aquilinosenra@lmp.ufrj.br

2005-07-01

The study evaluate an inorganic ion exchange to process the low level liquid radwaste of PWR nuclear plants, so that the level of the radioactivity in the effluents and the solid waste produced during the treatment of these liquid radwaste can be reduced. The work compares two types of ion exchange materials, a strong acid cation exchange resin, that is the material typically used to remove radionuclides from PWR nuclear plants wastes, and a mordenite zeolite. These exchange material were used to remove cesium from a synthetic effluent containing only this ion and another effluent containing cesium and cobalt. The breakthrough curves of the zeolite and resin using a fix bed reactor were compared. The results demonstrated that the zeolite is more efficient than the resin in removing cesium from a solution containing cesium and cobalt. The results also showed that a bed combining zeolite and resin can process more volume of an effluent containing cesium and cobalt than a bed resin alone. (author)

Advanced PWR Core Design with Siemens High-Plutonium-Content MOX Fuel Assemblies

International Nuclear Information System (INIS)

Dieter Porsch; Gerhard Schlosser; Hans-Dieter Berger

2000-01-01

The Siemens experience with plutonium recycling dates back to the late 1960s. Over the years, extensive research and development programs were performed for the qualification of mixed-oxide (MOX) technology and design methods. Today's typical reload enrichments for uranium and MOX fuel assemblies and modern core designs have become more demanding with respect to accuracy and reliability of design codes. This paper presents the status of plutonium recycling in operating high-burnup pressurized water reactor (PWR) cores. Based on actual examples, it describes the validation status of the design methods and stresses current and future needs for fuel assembly and core design including those related to the disposition of weapons-grade plutonium

Neutron Collar Evolution and Fresh PWR Assembly Measurements with a New Fast Neutron Passive Collar

Energy Technology Data Exchange (ETDEWEB)

Menlove, Howard Olsen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Geist, William H. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Root, Margaret A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rael, Carlos D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Belian, Anthony P. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-11-02

The passive neutron collar approach removes the effect of poison rods when using a 1mm Gd liner. This project sets out to solve the following challenges: BWR fuel assemblies have less mass and less neutron multiplication than PWR; and effective removal of cosmic ray spallation neutron bursts needed via QC tests.

Development of an advanced 16x165 Westinghouse type PWR fuel assembly for Slovenia

International Nuclear Information System (INIS)

Boone, M. L.; King, S. J.; Pulver, E. F.; Jeon, K.-L.; Esteves, R.; Kurincic, B.

2004-01-01

Industrias Nucleares do Brasil (INB), KEPCO Nuclear Fuel Company, Ltd. (KNFC), and Westinghouse Electric Company (Westinghouse) have jointly designed an advanced 16x16 Westinghouse type PWR fuel assembly. This advanced 16x16 Westinghouse type PWR fuel assembly, which will be implemented in both Kori Unit 2 (in Korea) and Angra Unit 1 (in Brazil) in January and March 2005, respectively, is an integral part of the utilities fuel management strategy. This same fuel design has also been developed for future use in Krsko Unit 1 (in Slovenia). In this paper we will describe the front-end nuclear fuel management activities utilized by the joint development team and describe how these activities played an integral part in defining the direction of the advanced 16x16 Westinghouse type PWR fuel assembly design. Additionally, this paper will describe how this design demonstrates improved margins under high duty plant operating conditions. The major reason for initiating this joint development program was to update the current 16x16 fuel assembly, which is also called 16STD. The current 16STD fuel assembly contains a non-optimized fuel rod diameter for the fuel rod pitch (i.e. 9.5 mm OD fuel rods at a 0.485 inch pitch), non-neutronic efficient components (i.e. Inconel Mid grids), no Intermediate Flow Mixer (IFM) grids, and other mechanical features. The advanced 16x16 fuel assembly is being designed for peak rod average burnups of up to 75 MWd/kgU and will use an optimized fuel rod diameter (i.e. 9.14 mm OD ZIRLO TM fuel rods), neutronic efficient components (i.e. ZIRLO TM Mid grids), ZIRLO TM Intermediate Flow Mixer (IFM) grids to improve Departure from Nucleate Boiling (DNB) margin, and many other mechanical features that improve design margins. Nuclear design activities in the areas of fuel cycle cost and fuel management were performed in parallel to the fuel assembly design efforts. As the change in reactivity due to the change in the fuel rod diameter influences directly

Thermohydraulic analysis of BWR and PWR spent fuel assemblies contained within square canisters

International Nuclear Information System (INIS)

Wiles, L.E.; McCann, R.A.

1981-09-01

This report presents the results of several thermohydraulic simulations of spent fuel assembly/canister configurations performed in support of a program investigating the feasibility of storing spent nuclear fuel assemblies in canisters that would be stored in an air environment. Eleven thermohydraulic simulations were performed. Five simulations were performed using a single BWR fuel assembly/canister design. The various cases were defined by changing the canister spacing and the heat generation rate of the fuel assembly. For each simulation a steady-state thermohydraulic solution was achieved for the region inside the canister. Similarly, six simulations were performed for a single PWR fuel assembly/canister design. The square fuel rod arrays were contained in square canisters which would permit closer packing of the canisters in a storage facility. However, closer packing of the canisters would result in higher fuel temperatures which would possibly have an adverse impact on fuel integrity. Thus, the most important aspect of the analysis was to define the peak fuel assembly temperatures for each case. These results are presented along with various temperature profiles, heat flux distributions, and air velocity profiles within the canister. 48 figures, 4 tables

Mixed PWR core loadings with inert matrix Pu-fuel assemblies

International Nuclear Information System (INIS)

Stanculescu, A.; Kasemeyer, U.; Paratte, J.-M.; Chawla, R.

1999-01-01

The most efficient way to enhance plutonium consumption in light water reactors is to eliminate the production of plutonium all together. This requirement leads to fuel concepts in which the uranium is replaced by an inert matrix. At PSI, studies have focused on employing ZrO 2 as inert matrix. Adding a burnable poison to such a fuel proves to be necessary. As a result of scoping studies, Er 2 O 3 was identified as the most suitable burnable poison material. The results of whole-core three-dimensional neutronics analyses indicated, for a present-day 1000 MW e pressurised water reactor, the feasibility of an asymptotic equilibrium four-batch cycle fuelled solely with the proposed PuO 2 -Er 2 O 3 -ZrO 2 inert matrix fuel (IMF). The present paper presents the results of more recent investigations related to 'real-life' situations, which call for transition configurations in which mixed IMF and UO 2 assembly loadings must be considered. To determine the influence of the introduction of IMF assemblies on the characteristics of a UO 2 -fuelled core, three-dimensional full-core calculations have been performed for a present-day 1000 MW e PWR containing up to 12 optimised IMF assemblies. (author)

HEXBU-3D, a three-dimensional PWR-simulator program for hexagonal fuel assemblies

International Nuclear Information System (INIS)

Karvinen, E.

1981-06-01

HEXBU-3D is a three-dimensional nodal simulator program for PWR reactors. It is designed for a reactor core that consists of hexagonal fuel assemblies and of big follower-type control assemblies. The program solves two-group diffusion equations in homogenized fuel assembly geometry by a sophisticated nodal method. The treatment of feedback effects from xenon-poisoning, fuel temperature, moderator temperature and density and soluble boron concentration are included in the program. The nodal equations are solved by a fast two-level iteration technique and the eigenvalue can be either the effective multiplication factor or the boron concentration of the moderator. Burnup calculations are performed by tabulated sets of burnup-dependent cross sections evaluated by a cell burnup program. HEXBY-3D has been originally programmed in FORTRAN V for the UNIVAC 1108 computer, but there is also another version which is operable on the CDC CYBER 170 computer. (author)

Incineration of PWR actinide waste to launch a low waste thorium-based energy production with ADSs

International Nuclear Information System (INIS)

Flocard, H.; David, S.; Naulin, F.; Schapira, J.P.

2001-01-01

We investigate a scenario for a smooth transition from an energy production based on PWR to one relying on the Thorium cycle. The reactors used during the transition are solid-fuel fast-neutron Accelerator Driven Systems whose initial fuel incorporates the Transuranium waste produced by the PWRs. Our work relies on a realistic computation of the neutronics of these systems. The benefits of implementing this scenario (compared to exploiting PWRs) in terms of the reduction of the total radiotoxicity (interim storage, final waste, and in core material) is evaluated along and after the transition period as well as the impact on a future repository. (author)

MELCOR Modeling of Air-Cooled PWR Spent Fuel Assemblies in Water empty Fuel Pools

Energy Technology Data Exchange (ETDEWEB)

Herranz, L. E.; Lopez, C.

2013-07-01

The OECD Spent Fuel Project (SFP) investigated fuel degradation in case of a complete Loss-Of- Coolant-Accident in a PWR spent fuel pool. Analyses of the SFP PWR ignition tests have been conducted with the 1.86.YT.3084.SFP MELCOR version developed by SNL. The main emphasis has been placed on assessing the MELCOR predictive capability to get reasonable estimates of time-to-ignition and fire front propagation under two configurations: hot neighbor (i.e., adiabatic scenario) and cold neighbor (i.e., heat transfer to adjacent fuel assemblies). A detailed description of hypotheses and approximations adopted in the MELCOR model are provided in the paper. MELCOR results accuracy was notably different between both scenarios. The reasons are highlighted in the paper and based on the results understanding a set of remarks concerning scenarios modeling is given.

A digital control and monitoring system for PWR waste-disposal systems

International Nuclear Information System (INIS)

Ueda, Toshiharu; Fuchigami, Kazuyuki; Shimozato, Masao; Takazawa, Kazuo

1982-01-01

Mitsubishi Electric has developed a digital control and monitoring system for PWR waste-disposal systems. This novel system has improved operability due to its automated operations and control, and integrated supervisory functions. The system includes other features to improve operability: sequence control by a control computer, direct-digital process control, integrated supervision of operation states by a supervisory computer and a high-speed dataway, and CRT interfacing between the computer and dataway. (author)

Waste package performance allocation system study report

International Nuclear Information System (INIS)

Memory, R.D.

1994-01-01

The Waste Package Performance Allocation system study was performed in order to provide a technical basis for the selection of the waste package period of substantially complete containment and its resultant contribution to the overall total system performance. This study began with a reference case based on the current Mined Geologic Disposal System (MGDS) baseline design and added a number of alternative designs. The waste package designs were selected from the designs being considered in detail during Advanced Conceptual Design (ACD). The waste packages considered were multi-barrier packages with a 0.95 cm Alloy 825 inner barrier and a 10, 20, or 45 cm thick carbon steel outer barrier. The waste package capacities varied from 6 to 12 to 21 Pressurized Water Reactor (PWR) fuel assemblies. The vertical borehole and in-drift emplacement modes were also considered, as were thermal loadings of 25, 57, and 114 kW/acre. The repository cost analysis indicated that the 21 PWR in-drift emplacement mode option with the 10 cm and 20 cm outer barrier thicknesses are the least expensive and that the 12 PWR in-drift case has approximately the same cost as the 6 PWR vertical borehole. It was also found that the cost increase from the 10 cm outer barrier waste package to the 20 cm waste package was less per centimeter than the increase from the 20 cm outer barrier waste package to the 45 cm outer barrier waste package. However, the repository cost was nearly linear with the outer barrier thickness for the 21 PWR in-drift case. Finally, corrosion rate estimates are provided and the relationship of repository cost versus waste package lifetime is discussed as is cumulative radionuclide release from the waste package and to the accessible environment for time periods of 10,000 years and 100,000 years

Comparison of problems and experience of core operation with distorted fuel element assemblies in VVER-1000 and PWR reactors

International Nuclear Information System (INIS)

Afanas'ev, A.

1999-01-01

The main reactors leading to distortion of fuel element assemblies during reactor operation were studied. A series of actions which compensate this effect was proposed. Criteria of operation limitation in VVER-1000 and PWR reactors are described

PWR-to-PWR fuel cycle model using dry process

International Nuclear Information System (INIS)

Iqbal, M.; Jeong, Chang Joon; Rho, Gyu Hong

2002-03-01

PWR-to-PWR fuel cycle model has been developed to recycle the spent fuel using the dry fabrication process. Two types of fuels were considered; first fuel was based on low initial enrichment with low discharge burnup and second one was based on more initial enrichment with high discharge burnup in PWR. For recycling calculations, the HELIOS code was used, in which all of the available fission products were considered. The decay of 10 years was applied for reuse of the spent fuel. Sensitivity analysis for the fresh feed material enrichment has also been carried out. If enrichment of the mixing material is increased the saving of uranium reserves would be decreased. The uranium saving of low burned fuel increased from 4.2% to 7.4% in fifth recycling step for 5 wt% to 19.00wt% mixing material enrichment. While for high burned fuel, there was no uranium saving, which implies that higher uranium enrichment required than 5 wt%. For mixing of 15 wt% enriched fuel, the required mixing is about 21.0% and 37.0% of total fuel volume for low and high burned fuel, respectively. With multiple recycling, reductions in waste for low and high burned fuel became 80% and 60%, for first recycling, respectively. In this way, waste can be reduced more and the cost of the waste disposal reduction can provide the economic balance

Development of computational methods to describe the mechanical behavior of PWR fuel assemblies

Energy Technology Data Exchange (ETDEWEB)

Wanninger, Andreas; Seidl, Marcus; Macian-Juan, Rafael [Technische Univ. Muenchen, Garching (Germany). Dept. of Nuclear Engineering

2016-10-15

To investigate the static mechanical response of PWR fuel assemblies (FAs) in the reactor core, a structural FA model is being developed using the FEM code ANSYS Mechanical. To assess the capabilities of the model, lateral deflection tests are performed for a reference FA. For this purpose we distinguish between two environments, in-laboratory and in-reactor for different burn-ups. The results are in qualitative agreement with experimental tests and show the stiffness decrease of the FAs during irradiation in the reactor core.

Vertical Drop Of 21-PWR Waste Package On Unyielding Surface

International Nuclear Information System (INIS)

S. Mastilovic; A. Scheider; S.M. Bennett

2001-01-01

The objective of this calculation is to determine the structural response of a 21-PWR (pressurized-water reactor) Waste Package (WP) subjected to the 2-m vertical drop on an unyielding surface at three different temperatures. The scope of this calculation is limited to reporting the calculation results in terms of stress intensities in two different WP components. The information provided by the sketches (Attachment I) is that of the potential design of the type of WP considered in this calculation, and all obtained results are valid for that design only

Thermal-hydraulic analysis of PWR small assembly for irradiation test of CARR

International Nuclear Information System (INIS)

Yin Hao; Zou Yao; Liu Xingmin

2015-01-01

The thermal-hydraulic behaviors of the PWR 4 × 4 small assembly tested in the high temperature and high pressure loop of China Advanced Research Reactor were analyzed. The CFD method was used to carry out 3D simulation of the model, thus detailed thermal-hydraulic parameters were obtained. Firstly, the simplified model was simulated to give the 3D temperature and velocity distributions and analyze the heat transfer process. Then the whole scale small assembly model was simulated and the simulation results were compared with those of simplified rod bundle model. Its flow behavior was studied and flow mixing characteristics of the grids were analyzed, and the mixing factor of the grid was calculated and can be used for further thermal-hydraulic study. It is shown that the highest temperature of the fuel rod meets the design limit and the mixing effect of the grid is obvious. (authors)

Pre design processing of waste of ex-resin without materials matrix from nuclear power plant type PWR 1000 MW

International Nuclear Information System (INIS)

Cerdas Tarigan

2010-01-01

Have been done pre design processing of waste ex-resin without capacities matrix materials from nuclear power plant type PWR 1000 MW During the time radioactive waste of ex-resin processed to use process of immobilization use matrix materials like mixture cement and epoxy resin and then conditioning. This process is not effective and efficient because end result volume of end product bigger than volume early operation system and maintenance of its installation more difficult. To overcome this created a design of technology processing of waste of ex- resin without matrix materials through process of strainer, drying and conditioning represent technological innovation newly processing of radioactive waste of ex-resin. Besides this process more effective and efficient, volume of end product waste much more small from volume early and operation system and maintenance of its easier installation. Pre design is expected to be used as a basis to make conceptual of pre design installation of strainer, drying and conditioning for the processing of waste of ex-resin from nuclear power plant type PWR 1000 MW. (author)

VANTAGE 5 PWR fuel assembly demonstration program at Virgil C. Summer nuclear station

International Nuclear Information System (INIS)

Warner, D.C.; Orr, W.L.

1985-01-01

VANTAGE 5 is an improved PWR fuel product designed and manufactured by Westinghouse Electric Corporation. The VANTAGE 5 fuel design features integral fuel burnable absorbers, intermediate flow mixer grids, axial blankets, high burnup capability, and a reconstitutable top nozzle. A demonstration program for this fuel design commenced in late 1984 in cycle 2 of the Virgil C. Summer Nuclear Station. Objectives for VANTAGE 5 fuel are reduced fuel cycle costs, better core operating margins, and increased design and operating flexibility. Inspections of the VANTAGE 5 demonstration assemblies are planned at each refueling outage

AREVA's fuel assemblies addressing high performance requirements of the worldwide PWR fleet

International Nuclear Information System (INIS)

Anniel, Marc; Bordy, Michel-Aristide

2009-01-01

Taking advantage of its presence in the fuel activities since the start of commercial nuclear worldwide operation, AREVA is continuing to support the customers with the priority on reliability, to: >participate in plant operational performance for the in core fuel reliability, the Zero Tolerance for Failure ZTF as a continuous improvement target and the minimisation of manufacturing/quality troubles, >guarantee the supply chain a proven product stability and continuous availability, >support performance improvements with proven design and technology for fuel management updating and cycle cost optimization, >support licensing assessments for fuel assembly and reloads, data/methodologies/services, >meet regulatory challenges regarding new phenomena, addressing emergent performance issues and emerging industry challenges for changing operating regimes. This capacity is based on supplies by AREVA accumulating very large experience both in manufacturing and in plant operation, which is demonstrated by: >manufacturing location in 4 countries including 9 fuel factories in USA, Germany, Belgium and France. Up to now about 120,000 fuel assemblies and 8,000 RCCA have been released to PWR nuclear countries, from AREVA European factories, >irradiation performed or in progress in about half of PWR world wide nuclear plants. Our optimum performances cover rod burn ups of to 82GWD/tU and fuel assemblies successfully operated under various world wide fuel management types. AREVA's experience, which is the largest in the world, has the extensive support of the well known fuel components such as the M5'TM'cladding, the MONOBLOC'TM'guide tube, the HTP'TM' and HMP'TM' structure components and the comprehensive services brought in engineering, irradiation and post irradiation fields. All of AREVA's fuel knowledge is devoted to extend the definition of fuel reliability to cover the whole scope of fuel vendor support. Our Top Reliability and Quality provide customers with continuous

A analysis of cementation technology for liquid radioactive-waste in PWR NPPs

International Nuclear Information System (INIS)

Chen Liang; Chen Li; Li Junhua

2009-01-01

Cementation is one of the most popular solidification technology for the low-and-intermediate level liquid radioactive waste. It has been applied in all of domestic PWR NPPs. The process characteristics and operation of the cementations in the different NPPs are introduced,and the advantage and disadvantage of the cementation are analyzed in this paper. A drum and a cask are compared as a package of the solidified waste, the drum can decrease over 50% final volume of the waste, furthermore the cost for manufacture and transportation for this drum is more cheaper than the cask, but an additional shielding may be necessary for the waste with higher level radioactivity that is packed in drum. More waste can be contained if an appropriate in-drum mixer is used while secondary waste will be unavoidable if the out-drum mixing is adopted. A carriage can make it easier to decontaminate on the surface of equipment and on the floor, furthermore the carriage is more economical than a roller conveyor in manufacture and maintenance. The cementation recipe for the waste should be optimized and additive material should be as less as possible to increase the containing rate of the waste. (authors)

SAS2H Generated Isotopic Concentrations For B and W 15X15 PWR Assembly

International Nuclear Information System (INIS)

J.W. Davis

1996-01-01

This analysis is prepared by the Mined Geologic Disposal System (MGDS) Waste Package Development Department (WPDD) to provide pressurized water reactor (PWR) isotopic composition data as a function of time for use in criticality analyses. The objectives of this evaluation are to generate burnup and decay dependant isotopic inventories and to provide these inventories in a form which can easily be utilized in subsequent criticality calculations

Essays of leaching in cemented products containing simulated waste from evaporator concentrated of PWR reactor

International Nuclear Information System (INIS)

Haucz, Maria Judite A.; Calabria, Jaqueline A. Almeida; Tello, Cledola Cassia O.; Candido, Francisco Donizete; Seles, Sandro Rogerio Novaes

2011-01-01

This paper evaluated the results from leaching resistance essays of cemented products, prepared from three distinct formulations, containing simulated waste of concentrated from the PWR reactor evaporator. The leaching rate is a parameter of qualification of solidified products containing radioactive waste and is determined in accordance with regulation ISO 6961. This procedure evaluates the capacity of transfer organic and inorganic substances presents in the waste through dissolution in the extractor medium. For the case of radioactive waste it is reached the more retention of contaminants in the cemented product, i.e.the lesser value of lixiviation rate. Therefore, this work evaluated among the proposed formulation that one which attend the criterion established in the regulation CNEN-NN-6.09

Dynamic structural analysis for assemblies of fuel elements in the core of a PWR

International Nuclear Information System (INIS)

Silva Macedo, L.V. da.

1991-01-01

It is presented a procedure for the dynamic structural analysis of a PWR core. Impacts between fuel assemblies may occur because of the existence of gaps between them. Thus, the problem is non-linear and an spectral analysis is avoided. It is necessary a time-history response analysis. The Modal Superposition Method with the Duhamel integral was used in order to solve the problem. It is presented an algorithm of solution and also results obtained with the STYCA computer program, developed in the basis of what was proposed here. (author)

Physics of plutonium and americium recycling in PWR using advanced fuel concepts

International Nuclear Information System (INIS)

Hourcade, E.

2004-01-01

PWR waste inventory management is considered in many countries including Frances as one of the main current issues. Pu and Am are the 2 main contents both in term of volume and long term radio-toxicity. Waiting for the Generation IV systems implementation (2035-2050), one of the mid-term solutions for their transmutation involves the use of advanced fuels in Pressurized Water Reactors (PWR). These have to require as little modification as possible of the core internals, the cooling system and fuel cycle facilities (fabrication and reprocessing). The first part of this paper deals with some neutronic characteristics of Pu and/or Am recycling. In a second part, 2 technical solutions MOX-HMR and APA-DUPLEX-84 are presented and the third part is devoted to the study of a few global strategies. The main neutronic parameters to be considered for Pu and Am recycling in PWR are void coefficient, Doppler coefficient, fraction of delayed neutrons and power distribution (especially for heterogeneous configurations). The modification of the moderation ratio, the opportunity to use inert matrices (targets), the optimisation of Uranium, Plutonium and Americium contents are the key parameters to play with. One of the solutions (APA-DUPLEX-84) presented here is a heterogeneous assembly with regular moderation ratio composed with both target fuel rods (Pu and Am embedded in an inert matrix) and standard UO 2 fuel rods. An EPR (European Pressurised Reactor) type reactor, loaded only with assemblies containing 84 peripheral targets, can reach an Americium consumption rate of (4.4; 23 kg/TWh) depending on the assembly concept. For Pu and Am inventories stabilisation, the theoretical fraction of reactors loaded with Pu + Am or Pu assemblies is about 60%. For Americium inventory stabilisation, the fraction decreases down to 16%, but Pu is produced at a rate of 18.5 Kg/TWh (-25% compared to one through UOX cycle)

Analysis of experimental measurements of PWR fresh and spent fuel assemblies using Self-Interrogation Neutron Resonance Densitometry

Energy Technology Data Exchange (ETDEWEB)

LaFleur, Adrienne M., E-mail: alafleur@lanl.gov; Menlove, Howard O., E-mail: hmenlove@lanl.gov

2015-05-01

Self-Interrogation Neutron Resonance Densitometry (SINRD) is a new NDA technique that was developed at Los Alamos National Laboratory (LANL) to improve existing nuclear safeguards measurements for LWR fuel assemblies. The SINRD detector consists of four fission chambers (FCs) wrapped with different absorber filters to isolate different parts of the neutron energy spectrum and one ion chamber (IC) to measure the gross gamma rate. As a result, two different techniques can be utilized using the same SINRD detector unit and hardware. These techniques are the Passive Neutron Multiplication Counter (PNMC) method and the SINRD method. The focus of the work described in this paper is the analysis of experimental measurements of fresh and spent PWR fuel assemblies that were performed at LANL and the Korea Atomic Energy Research Institute (KAERI), respectively, using the SINRD detector. The purpose of these experiments was to assess the following capabilities of the SINRD detector: 1) reproducibility of measurements to quantify systematic errors, 2) sensitivity to water gap between detector and fuel assembly, 3) sensitivity and penetrability to the removal of fuel rods from the assembly, and 4) use of PNMC/SINRD ratios to quantify neutron multiplication and/or fissile content. The results from these simulations and measurements provide valuable experimental data that directly supports safeguards research and development (R&D) efforts on the viability of passive neutron NDA techniques and detector designs for partial defect verification of spent fuel assemblies. - Highlights: • Experimental measurements of PWR fresh and spent FAs were performed with SINRD. • Good agreement of MCNPX and measured results confirmed accuracy of SINRD model. • For fresh fuel, SINRD and PNMC ratios were not sensitive to water gaps of ≤5-mm. • Practical use of SINRD would be in Fork detector to reduce systematic uncertainties.

Nupec thermal hydraulic test to evaluate post-DNB characteristics for PWR fuel assemblies (1. general test plan and results)

International Nuclear Information System (INIS)

Norio, Kono; Kenji, Murai; Kaichiro, Misima; Takayuki, Suemura; Yoshiei, Akiyama; Keiichi, Hori

2001-01-01

In the present thermal hydraulic design of Pressurized Water Reactor (PWR), a departure from nucleate boiling (DNB) under anticipated transient conditions is not allowed. However, it is recognized that the DNB dose not cause a fuel rod failure immediately, and a suitable reactor trip can prevent the core from severe damages. If the fuel rod temperature under the post-DNB conditions can be accurately evaluated, the potentially existing margin in the present design method will be quantitatively assessed. To establish the heat transfer evaluation method on post-DNB event for PWR thermal hydraulic design, Nuclear Power Engineering Corporation (NUPEC) started a program, NUPEC Thermal Hydraulic Test to Evaluate Post-DNB Characteristics for PWR Fuel Assemblies (NUPEC-TH-P), in 1995 (hereinafter the year means fiscal year) under the sponsorship of Ministry of Economy, Trade and industry (METI). This program is now under going until 2001. This paper is to show the overall plan and the status of NUPEC-TH-P. (authors)

Basic information about development and construction of a PWR

International Nuclear Information System (INIS)

Meyer, P.J.

1977-01-01

1.0) Plant layout of a PWR; 2.0) principle design of a PWR and the reactor coolant system; 3.0) reactor auxiliary and ancillary systems; 3.1) volume control system; 3.2) boric acid control and chemical feeding system; 3.3) coolant purification and degassing system; 3.4) coolant storage and treatment system; 3.5) nuclear component cooling system; 3.6) liquid waste processing system; 3.7) gaseous waste processing system; 4.0) residual heat removal system; 5.0) emergency feedwater system; 6.0) containment design; 7.0) fuel handling, storage and transport system in a PWR. (orig.) [de

Gadolinia experience and design for PWR fuel cycles

International Nuclear Information System (INIS)

Stephenson, L. C.

2000-01-01

The purpose of this paper is to describe Siemens Power Corporation's (SPC) current experience with the burnable absorber gadolinia in PWR fuel assemblies, including optimized features of SPC's PWR gadolinia designs, and comparisons with other burnable absorbers. Siemens is the world leader in PWR gadolinia experience. More than 5,900 Siemens PWR gadolinia-bearing fuel assemblies have been irradiated. The use of gadolinia-bearing fuel provides significant flexibility in fuel cycle designs, allows for low radial leakage fuel management and extended operating cycles, and reduces BOC (beginning-of-cycle) soluble boron concentrations. The optimized use of an integral burnable neutron absorber is a design feature which provides improved economic performance for PWR fuel assemblies. This paper includes a comparison between three different types of integral burnable absorbers: gadolinia, Zirconium diboride and erbia. Fuel cycle design studies performed by Siemens have shown that the enrichment requirements for 18-24 month fuel cycles utilizing gadolinia or zirconium diboride integral fuel burnable absorbers can be approximately the same. Although a typical gadolinia residual penalty for a cycle design of this length is as low as 0.02-0.03 wt% U-235, the design flexibility of gadolinia allows for very aggressive low-leakage core loading plans which reduces the enrichment requirements for gadolinia-bearing fuel. SPC has optimized its use of gadolinia in PWR fuel cycles. Typically, low (2-4) weight percent Gd 2 O 3 is used for beginning to middle of cycle reactivity hold down as well as soluble boron concentration holddown at BOC. Higher concentrations of Gd 2 O 3 , such as 6 and 8 wt%, are used to control power peaking in assemblies later in the cycle. SPC has developed core strategies that maximize the use of lower gadolinia concentrations which significantly reduces the gadolinia residual reactivity penalty. This optimization includes minimizing the number of rods with

Lateral hydraulic forces calculation on PWR fuel assemblies with computational fluid dynamics codes; Calculo de fuerzas laterales hidraulicas en elementos combustibles tipo PWR con codigos de dinamica de fluidos coputacional

Energy Technology Data Exchange (ETDEWEB)

Corpa Masa, R.; Jimenez Varas, G.; Moreno Garcia, B.

2016-08-01

To be able to simulate the behavior of nuclear fuel under operating conditions, it is required to include all the representative loads, including the lateral hydraulic forces which were not included traditionally because of the difficulty of calculating them in a reliable way. Thanks to the advance in CFD codes, now it is possible to assess them. This study calculates the local lateral hydraulic forces, caused by the contraction and expansion of the flow due to the bow of the surrounding fuel assemblies, on of fuel assembly under typical operating conditions from a three loop Westinghouse PWR reactor. (Author)

Refitting of the 'Celimene' hot cell for following up the fuel assembly of 900 MWe PWR power reactors

International Nuclear Information System (INIS)

Lhermenier, Andre; Van Craeynest, J.-C.

1980-05-01

The 'Celimene' cell adjoining the EL3 reactor provides for the acceptance, handling and the examination of irradiated fuel assemblies from power reactors (length approximately 4m, weight approximately 700 kg). Within the framework of the PWR fuel behavior follow-up or reprocessing, it is possible to extract an assembly representative of the normal fuel cycle, carry out non destructive tests on this assembly, extract pencils from it and re-insert this assembly, after refitting the head, into the normal fuel cycle for handling in a reprocessing plant or storage pond. Given suitable refitting techniques, the re-irradiation of the assembly can be considered after examination. Significant changes have been made to the buildings and the hoist facilities for handling very heavy flasks. It was necessary to rearrange the handling, machining and in-cell storage facilities. The development of an inspection rig will make it possible, some time in 1980, to carry out non destructive tests of assemblies, optical and metrological examination of assemblies prior to dismantling or of the structure after dismantling [fr

SAS2H Generated Isotopic Concentrations For B&W 15X15 PWR Assembly (SCPB:N/A)

Energy Technology Data Exchange (ETDEWEB)

J.W. Davis

1996-08-29

This analysis is prepared by the Mined Geologic Disposal System (MGDS) Waste Package Development Department (WPDD) to provide pressurized water reactor (PWR) isotopic composition data as a function of time for use in criticality analyses. The objectives of this evaluation are to generate burnup and decay dependant isotopic inventories and to provide these inventories in a form which can easily be utilized in subsequent criticality calculations.

Preliminary conceptual design of a geological disposal system for high-level wastes from the pyroprocessing of PWR spent fuels

Energy Technology Data Exchange (ETDEWEB)

Choi, Heui-Joo, E-mail: hjchoi@kaeri.re.kr [Korea Atomic Energy Research Institute, 1045 Daeduk-Daero, Yuseong, Daejon 305-353 (Korea, Republic of); Lee, Minsoo; Lee, Jong Youl [Korea Atomic Energy Research Institute, 1045 Daeduk-Daero, Yuseong, Daejon 305-353 (Korea, Republic of)

2011-08-15

Highlights: > A geological disposal system consists of disposal overpacks, a buffer, and a deposition hole or a disposal tunnel for high-level wastes from a pyroprocessing of PWR spent fuels is proposed. The amount and characteristics of high-level wastes are analyzed based on the material balance of pyroprocessing. > Four kinds of deposition methods, two horizontal and two vertical, are proposed. Thermal design is carried out with ABAQUS program. The spacing between the disposal modules is determined for the peak temperature in buffer not to exceed 100 deg. C. > The effect of the double-layered buffer is compared with the traditional single-layered buffer in terms of disposal density. Also, the effect of cooling time (aging) is illustrated. > All the thermal calculations are represented by comparing the disposal area of PWR spent fuels with the same cooling time. - Abstract: The inventories of spent fuels are linearly dependent on the production of electricity generated by nuclear energy. Pyroprocessing of PWR spent fuels is one of promising technologies which can reduce the volume of spent fuels remarkably. The properties of high-level wastes from the pyroprocessing are totally different from those of spent fuels. A geological disposal system is proposed for the high-level wastes from pyroprocessing of spent fuels. The amount and characteristics of high-level wastes are analyzed based on the material balance of pyroprocessing. Around 665 kg of monazite ceramic wastes are expected from the pyroprocessing of 10 MtU of PWR spent fuels. Decay heat from monazite ceramic wastes is calculated using the ORIGEN-ARP program. Disposal modules consisting of storage cans, overpacks, and a deposition hole or a disposal tunnel are proposed. Four kinds of deposition methods are proposed. Thermal design is carried out with ABAQUS program and geological data obtained from the KAERI Underground Research Tunnel. Through the thermal analysis, the spacing between the disposal modules

Cementation of Radioactive Waste from a PWR with Calcium Sulfoaluminate Cement

International Nuclear Information System (INIS)

Li, J.

2013-01-01

Spent radioactive ion-exchange resin (SIER) and evaporation concentrates are radioactive wastes that are produced at by pressurized water reactor (PWR) nuclear power stations. Borate, which is used as a retardent for cement, is also present as a moderator in a PWR, therefore, borate will be present in both ion-exchange resins and evaporation concentrates. In this study the use of Calcium sulfoaluminate cements (SAC) as encapsulation medium for these waste streams was investigated. The study involved the manufacturing of different cement test samples with different amounts of SAC cement, waste resins (50% water content) and admixtures. In order to reduce hydration heat during 200 L solidification experiments, different admixtures were investigated. Initial results based on compressive strength tests and hydration temperature studies, indicated that zeolite was the best admixture for the current waste form. Experiments indicated that the addition of resin material into the current cement matrix reduces the hydration heat during curing Experimental results indicated that a combination of SAC (35 wt. %), zeolite (7 wt. %) mix with 42 wt. % resins (50% water content) and 16 wt. % of water forms a optimum cured monolith with low hydration heat. The microstructures of hydrated OPC, SAC and SAC with zeolite addition were studied using a Scanning Electron Microscopy (SEM). SEM results indicated that the SAC matrices consist of a needle type structure that changed gradually into a flake type structure with the addition of zeolite. Additionally, the presence of zeolite material inside the SAC matrix reduced the leaching rates of radionuclides significantly. In a final 200 L grouting test, measured results indicated a hydration temperature below 90oC withno thermal cracks after solidified. The influence of radiation on the compressive strength and possible gas generation (due to radiolysis) on cement waste forms containing different concentrations ion exchange resin was

Development of built-in debris-filter bottom nozzle for PWR fuel assemblies

International Nuclear Information System (INIS)

Juntaro Shimizu; Kazuki Monaka; Masaji Mori; Kazuo Ikeda

2005-01-01

Mitsubishi Heavy Industries, Ltd. (MHI) has worked to improve the capability of anti debris bottom nozzle for a PWR fuel assembly. The Current debris filter bottom nozzle (DFBN) having 4mm diameter flow holes can capture the larger size of debris than the flow hole inner diameter. MHI has completed the development of the built-in debris filter bottom nozzle, which is the new idea of the debris-filter for high burnup (55GWd/t assembly average burnup). Built-in debris filter bottom nozzle consists of the blades and nozzle body. The blades made from inconel strip are embedded and welded on the grooved top surface of the bottom nozzle adapter plate. A flow hole is divided by the blade and the trap size of the debris is reduced. Because the blades block the coolant flow, it was anticipated to increase the pressure loss of the nozzle, however, adjusting the relation between blade and taper shape of the flow hole, the pressure loss has been successfully maintained the satisfactory level. Grooves are cut on the nozzle plate; nevertheless, the additional skirts on the four sides of the nozzle compensate the structural strength. (authors)

HORIZONTAL LIFTING OF 5 DHLW/DOE LONG, 12-PWR LONG AND 24-BWR WASTE PACKAGES

International Nuclear Information System (INIS)

V. de la Brosse

2001-01-01

The objective of this calculation was to determine the structural response of a 12-Pressurized Water Reactor (PWR) Long, a 24-Boiling Water Reactor (BWR) and a 5-Defense High Level Waste/Department of Energy (DHLW/DOE)--Long spent nuclear fuel waste packages lifted in a horizontal position. The scope of this calculation was limited to reporting the calculation results in terms of maximum stress intensities in the trunnion collar sleeves. In addition, the maximum stress intensities in the inner and outer shells of the waste packages were presented for illustrative purposes. The information provided by the sketches (Attachments I, II and III) is that of the potential design of the types of waste packages considered in this calculation, and all obtained results are valid for these designs only. This calculation is associated with the waste package design and was performed by the Waste Package Design Section in accordance with the ''Technical work plan for: Waste Package Design Description for LA'' (Ref. 7). AP-3.12Q, Calculations (Ref. 13), was used to perform the calculation and develop the document

Criticality calculations of a generic fuel container for fuel assemblies PWR, by means of the code MCNP

International Nuclear Information System (INIS)

Vargas E, S.; Esquivel E, J.; Ramirez S, J. R.

2013-10-01

The purpose of the concept of burned consideration (Burn-up credit) is determining the capacity of the calculation codes, as well as of the nuclear data associates to predict the isotopic composition and the corresponding neutrons effective multiplication factor in a generic container of spent fuel during some time of relevant storage. The present work has as objective determining this capacity of the calculation code MCNP in the prediction of the neutrons effective multiplication factor for a fuel assemblies arrangement type PWR inside a container of generic storage. The calculations are divided in two parts, the first, in the decay calculations with specified nuclide concentrations by the reference for a pressure water reactor (PWR) with enriched fuel to 4.5% and a discharge burned of 50 GW d/Mtu. The second, in criticality calculations with isotopic compositions dependent of the time for actinides and important fission products, taking 30 time steps, for two actinide groups and fission products. (Author)

Open and closed fuel cycle of HWR and PWR. How large is the high-level radioactive wastes repository; Ciclos de combustible abierto y cerrado con HWR y PWR. ?Cuanto mas grande es el repositorio de residuos radiactivos de alta actividad?

Energy Technology Data Exchange (ETDEWEB)

Bevilacqua, Arturo M. [Comision Nacional de Energia Atomica, San Carlos de Bariloche (Argentina). Centro Atomico Bariloche

1996-07-01

A conceptual analysis was carried out on the size of a high-level wastes (HLW) repository for the waste arising from once-through and closed fuel cycles with (HLW) and PWR. The mass, the activity and thermal loading was calculated with the ORIGEN2.1 computer code for the spent fuel and for the high-level liquid wastes. It was considered a minimum burnup of 7.000 MW.d/t U and 33.000 MW.d/t U for HWR and PWR respectively, cooling times of 20 and 55 years, reprocessing recovery ratios of 99% and 99.7% and a total electricity production of 81.6 GW(e).a. It was concluded that the cooling time is the most important repository size reproduction parameter for the closed cycles. On the other hand, the spent fuel mass for the once-through cycles does not depend on the cooling time what prevents repository size reduction once a cooling time of 55 years is reached. The repository size reduction in the case of HWR is larger than in the case of PWR, owing to the larger fuel mass required to produce the specific electricity amount. (author)

A Feasibility Study on Core Cooling of Reduced-Moderation PWR for the Large Break LOCA

International Nuclear Information System (INIS)

Hiroyuki Yoshida; Akira Ohnuki; Hajime Akimoto

2002-01-01

A design study of a reduced-moderation water reactor (RMWR) with tight lattice core is being carried out at the Japan Atomic Energy Research Institute (JAERI) as one candidate for future reactors. The concept is developed to achieve a conversion ratio greater than unity using the tight lattice core (volume ratio of moderator to fuel is around 0.5 and the gap spacing between the fuel rods is remarkably narrower than in a reactor currently operated). Under such tight configuration, the core thermal margin becomes smaller and should be evaluated in a normal operation and also during the reflood phase in a large break loss-of-coolant accident (LBLOCA) for PWR type reactors. In this study, we have performed a feasibility evaluation on core cooling of reduced moderation PWR for the LBLOCA (200% break). The evaluation was performed for the primary system after the break by the REFLA/TRAC code. The core thermal output of the reduced moderation PWR is 2900 MWt, the gap between adjacent fuel rods is 1 mm, and heavy water is used as the moderator and coolant. The present design adopts seed fuel assemblies (MOX fuel) and several blanket fuel assemblies. In the blanket fuel assemblies, power density is lower than that of the seed fuel assemblies. Then, we set a channel box to each fuel assembly in order to adjust the flow rate in each assembly, because the possibility that the coolant boils in the seed fuel assemblies is very high. The pressure vessel diameter is bigger in comparison with a current PWR and core height is smaller than the current one. The current 4-loop PWR system is used, and, however, to fit into the bigger pressure vessel volume (about 1.5 times), we set up the capacity of the accumulator (1.5 times of the current PWR). Although the maximum clad temperature reached at about 1200 K in the position of 0.6 m from the lower core support plate, it is sufficiently lower than the design criteria of the current PWR (1500 K). The core cooling of the reduced moderation

Fuel assembly loads during a hypothetical blowdown event in a PWR

International Nuclear Information System (INIS)

Stabel, J.; Bosanyi, B.; Kim, J.D.

1991-01-01

As a consequence of a hypothetical sudden break of the main coolant pipe of a PWR, RPV-internals and fuel assemblies (FA's) are undergoing horizontal and vertical motions. FA's may impact against each other, against core shroud or against lower core support. The corresponding impact loads must be absorbed by the FA spacer grids and guide thimbles. In this paper FA-loads are calculated with and without consideration of Fluid-Structure-Interaction (FSI) effects for assumed different break sizes of the main coolant pipe. The analysis has been performed for a hypothetical cold leg break of a typical SIEMENS-4 loop plant. For this purpose the codes DAPSY/DAISY (GRS, Germany) were coupled with the structural code KWUSTOSS (SIEMENS). It is shown that the FA loads obtained in calculations with consideration of FSI effects are by a factor of 2-4 lower than those obtained in the corresponding calculations without consideration of FSI. (author)

Assessment of options for the treatment of Sizewell PWR liquid effluent

International Nuclear Information System (INIS)

Hornby, J.; Allam, J.; Knibbs, R.H.

1992-01-01

This report describes the origins of PWR liquid waste streams, their composition and rates of arising. Data has been collected from operational PWRs and estimates obtained for Sizewell B PWR liquid waste streams. Current liquid waste treatment practices are reviewed and assessments made of established and novel treatment techniques which could be applicable to Sizewell B. A short list of treatment options is given and recommendations are made relating to established treatment technologies suitable for Sizewell B and also to development work on more novel treatments which could lead to a reduction in waste disposal volumes. (author)

Device Assembly Facility (DAF) Glovebox Radioactive Waste Characterization

International Nuclear Information System (INIS)

Dominick, J L

2001-01-01

The Device Assembly Facility (DAF) at the Nevada Test Site (NTS) provides programmatic support to the Joint Actinide Shock Physics Experimental Research (JASPER) Facility in the form of target assembly. The target assembly activities are performed in a glovebox at DAF and include Special Nuclear Material (SNM). Currently, only activities with transuranic SNM are anticipated. Preliminary discussions with facility personnel indicate that primarily two distributions of SNM will be used: Weapons Grade Plutonium (WG-Pu), and Pu-238 enhanced WG-Pu. Nominal radionuclide distributions for the two material types are included in attachment 1. Wastes generated inside glove boxes is expected to be Transuranic (TRU) Waste which will eventually be disposed of at the Waste Isolation Pilot Plant (WIPP). Wastes generated in the Radioactive Material Area (RMA), outside of the glove box is presumed to be low level waste (LLW) which is destined for disposal at the NTS. The process knowledge quantification methods identified herein may be applied to waste generated anywhere within or around the DAF and possibly JASPER as long as the fundamental waste stream boundaries are adhered to as outlined below. The method is suitable for quantification of waste which can be directly surveyed with the Blue Alpha meter or swiped. An additional quantification methodology which requires the use of a high resolution gamma spectroscopy unit is also included and relies on the predetermined radionuclide distribution and utilizes scaling to measured nuclides for quantification

Study of chemical additives in the cementation of radioactive waste of PWR reactors

International Nuclear Information System (INIS)

Vieira, Vanessa Mota; Tello, Cledola Cassia Oliveira de

2012-01-01

In this research it has been studied the effects of chemical admixtures in the cementation process of radioactive wastes. These additives are used to improve the properties of waste cementation process, both of the paste and of the solidified product. However there are a large variety of these materials that are frequently changed or taken out of the market. Then it is essential to know the commercially available materials and their effects. The tests were carried out with a solution simulating the evaporator concentrate waste coming from PWR nuclear reactors. It was cemented using two formulations, A and B, incorporating higher or lower amount of waste, respectively. It was added chemical admixtures from two manufacturers (S and H), which were: accelerators, set retarders and superplasticizers. The experiments were organized by a factorial design 23. The measured parameters were: the viscosity, the setting time, the paste and product density and the compressive strength. The parameter evaluated in this study was the compressive strength at age of 28 days, is considered essential security issues relating to the handling, transport and storage of cemented waste product. The results showed that the addition of accelerators improved the compressive strength of the cemented products. (author)

Essays of leaching in cemented products containing simulated waste from evaporator concentrated of PWR reactor; Ensaios de lixiviacao em produtos cimentados contendo rejeito simulado de concentrado do evaporador de reator PWR

Energy Technology Data Exchange (ETDEWEB)

Haucz, Maria Judite A.; Calabria, Jaqueline A. Almeida; Tello, Cledola Cassia O.; Candido, Francisco Donizete; Seles, Sandro Rogerio Novaes, E-mail: hauczmj@cdtn.b, E-mail: jaalmeida@cdtn.b, E-mail: tellocc@cdtn.b, E-mail: fdc@cdtn.b, E-mail: seless@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2011-10-26

This paper evaluated the results from leaching resistance essays of cemented products, prepared from three distinct formulations, containing simulated waste of concentrated from the PWR reactor evaporator. The leaching rate is a parameter of qualification of solidified products containing radioactive waste and is determined in accordance with regulation ISO 6961. This procedure evaluates the capacity of transfer organic and inorganic substances presents in the waste through dissolution in the extractor medium. For the case of radioactive waste it is reached the more retention of contaminants in the cemented product, i.e.the lesser value of lixiviation rate. Therefore, this work evaluated among the proposed formulation that one which attend the criterion established in the regulation CNEN-NN-6.09

Impact forces on a core shroud of an excited PWR fuel assembly

Energy Technology Data Exchange (ETDEWEB)

Collard, B.; Vallory, J. [CEA Cadarache, 13 - Saint Paul lez Durance (France)

2001-07-01

Seismic excitation of PWR internals may induce large motions of the fuel assemblies (FA). This could result in impact between assemblies or between assemblies and core shroud. Forces generated during these shocks are often the basis for the maximum design loads of the spacer grids and fuel rods. An experimental program has been conducted at the French Nuclear Reactor Directorate (CEA) to measure the impact forces of a reduced scale FA on the test section under different environmental conditions. Within the framework of the tests presented, the effect of the FA environment (air, stagnant water, water under flow) on the maximum impact forces measured at grid levels and on the energy dissipated during the shock is examined. A 'fluid cushioning' effect (dissipative) between the grids and the wall is sought. Experimental results show that the axial flow has a great influence on the impact forces. The greater the axial flow velocity is, the lower the impact forces are. The tests of impact of an assembly on a wall were analyzed compared to the tests carried out without impact. This analysis related on the measured forces of impact and the variation of the measured/computed total energy of the system. The whole of these tests in air and water shows that the 'fluid cushioning' effect required exists but is not significant. Thus the presence of water does not decrease the forces of impact, and does not amplify the quantity of energy dissipated during the shock. The fact that the 'fluid cushioning' effect is weak compared to more analytical tests probably comes from our 'not perfect' or 'realistic' conditions of tests which involve an angle between the grid and the wall at the shock moment.

Impact forces on a core shroud of an excited PWR fuel assembly

International Nuclear Information System (INIS)

Collard, B.; Vallory, J.

2001-01-01

Seismic excitation of PWR internals may induce large motions of the fuel assemblies (FA). This could result in impact between assemblies or between assemblies and core shroud. Forces generated during these shocks are often the basis for the maximum design loads of the spacer grids and fuel rods. An experimental program has been conducted at the French Nuclear Reactor Directorate (CEA) to measure the impact forces of a reduced scale FA on the test section under different environmental conditions. Within the framework of the tests presented, the effect of the FA environment (air, stagnant water, water under flow) on the maximum impact forces measured at grid levels and on the energy dissipated during the shock is examined. A 'fluid cushioning' effect (dissipative) between the grids and the wall is sought. Experimental results show that the axial flow has a great influence on the impact forces. The greater the axial flow velocity is, the lower the impact forces are. The tests of impact of an assembly on a wall were analyzed compared to the tests carried out without impact. This analysis related on the measured forces of impact and the variation of the measured/computed total energy of the system. The whole of these tests in air and water shows that the 'fluid cushioning' effect required exists but is not significant. Thus the presence of water does not decrease the forces of impact, and does not amplify the quantity of energy dissipated during the shock. The fact that the 'fluid cushioning' effect is weak compared to more analytical tests probably comes from our 'not perfect' or 'realistic' conditions of tests which involve an angle between the grid and the wall at the shock moment

Nuclear-data uncertainty propagations in burnup calculation for the PWR assembly

International Nuclear Information System (INIS)

Wan, Chenghui; Cao, Liangzhi; Wu, Hongchun; Shen, Wei

2017-01-01

Highlights: • The DRAGON 5.0 and NECP-CACTI have been implemented in UNICORN. • The effects of different neutronics methods on S&U results were quantified. • Uncertainty analysis has been applied to burnup calculation of PWR assembly. • The uncertainties of eigenvalue and few-group constants have been quantified. - Abstract: In this paper, our home-developed lattice code NECP-CACTI has been implemented into our UNICORN code to perform sensitivity and uncertainty analysis for the lattice calculations. The verified multigroup cross-section perturbation model and methods of the sensitivity and uncertainty analysis are established and applied to different lattice codes in UNICORN. As DRAGON5.0 and NECP-CACTI are available for the lattice calculations in UNICORN now, the effects of different neutronics methods (including methods for the neutron-transport and resonance self-shielding calculations) on the results of sensitivity and uncertainty analysis were studied in this paper. Based on NECP-CACTI, uncertainty analysis using the statistical sampling method has been performed to the burnup calculation for the fresh-fueled TMI-1 assembly, propagating the nuclear-data uncertainties to k_∞ and two-group constants of the lattice calculation with depletions. As results shown, for different neutronics methods, it can be observed that different methods of the neutron-transport calculation introduce no differences to the results of sensitivity and uncertainty analysis, while different methods of the resonance self-shielding calculation would impact the results. With depletions of the TMI-1 assembly, for k_∞, the relative uncertainty varies between 0.45% and 0.60%; for two-group constants, the largest variation is between 0.35% and 2.56% for vΣ_f_,_2. Moreover, the most significant contributors to the uncertainty of k_∞ and two-group constants varied with depletions are determined.

Pressure loss tests for DR-BEP of fullsize 17 x 17 PWR fuel assembly

International Nuclear Information System (INIS)

Chung, Moon Ki; Chun, Se Young; Chang, Seok Kyu; Won, Soon Youn; Cho, Young Rho; Kim, Bok Deuk; Min, Kyoung Ho

1993-01-01

This report describes the conditions, procedure and results in the pressure loss tests carried out for a double grid type debris resistance bottom end piece (DR-BEP) designed by KAERI. In this test, the pressure loss coefficients of the full size 17 x 17 PWR simulated fuel assembly with DR-BET and with standard-BEP were measured respectively, and the pressure loss coefficients of DR-BEP were compared with the coefficients of STD-BET. The test conditions fall within the ranges of loop pressure from 5.2 to 45 bar, loop temperature from 27 to 221 deg C and Reynolds number in fuel bundle from 2.17 x 10 4 to 3.85 x 10 5 . (Author) 5 refs., 18 figs., 5 tabs

High mechanical performance of Areva upgraded fuel assemblies for PWR in USA

International Nuclear Information System (INIS)

Gottuso, Dennis; Canat, Jean-Noel; Mollard, Pierre

2007-01-01

The merger of the product portfolios of the former Siemens and Framatome fuel businesses gave rise to a new family of PWR products which combine the best features of the different technologies to enhance the main performance of each of the existing products. In this way, the technology of each of the three main fuel assembly types usually delivered by AREVA NP, namely Mark-BW TM , HTP TM and AFA 3G TM has been enriched by one or several components from the others which contributes to improve their robustness and to enhance their performance. The combined experience of AREVA's products shows that the ROBUST FUELGUARD TM , the HMP TM end grid, the MONOBLOC TM guide tube, a welded structure, M5 R material for every zirconium component and an upper QUICK-DISCONNECT TM are key features for boosting fuel assembly robustness. The ROBUST FUELGUARD benefits from a broad experience demonstrating its high efficiency in stopping debris. In addition, its mechanical strength has been enhanced and the proven blade design homogenizes the downstream flow distribution to strongly reduce excitation of fuel rods. The resistance to rod-to-grid fretting resistance of AREVA's new products is completed by the use of a lower HMP grid with 8 lines of contact to insure low wear. The Monobloc guide tube with a diameter maximized to strengthen the fuel assembly stiffness, excludes through its uniform outer geometry any local condition which could weaken guide tube straightness. The application of a welded cage to all fuel assemblies of the new family of products in combination with stiffer guide tubes and optimized hold-down assures each fuel assembly enhanced resistance to distortion. The combination of these features has been widely demonstrated as an effective method to reduce the risk of incomplete RCCA insertion and significantly reduce assembly distortion. Thanks to its enhanced performance, M5 alloy insures that all fuel assemblies in the family maintain their performance in all

Development of unfolding method to obtain pin-wise source strength distribution from PWR spent fuel assembly measurement

International Nuclear Information System (INIS)

Sitompul, Yos Panagaman; Shin, Hee-Sung; Park, Se-Hwan; Oh, Jong Myeong; Seo, Hee; Kim, Ho Dong

2013-01-01

An unfolding method has been developed to obtain a pin-wise source strength distribution of a 14 × 14 pressurized water reactor (PWR) spent fuel assembly. Sixteen measured gamma dose rates at 16 control rod guide tubes of an assembly are unfolded to 179 pin-wise source strengths of the assembly. The method calculates and optimizes five coefficients of the quadratic fitting function for X-Y source strength distribution, iteratively. The pin-wise source strengths are obtained at the sixth iteration, with a maximum difference between two sequential iterations of about 0.2%. The relative distribution of pin-wise source strength from the unfolding is checked using a comparison with the design code (Westinghouse APA code). The result shows that the relative distribution from the unfolding and design code is consistent within a 5% difference. The absolute value of the pin-wise source strength is also checked by reproducing the dose rates at the measurement points. The result shows that the pin-wise source strengths from the unfolding reproduce the dose rates within a 2% difference. (author)

Source Term Characteristics Analysis for Structural Components in PWR spent fuel assembly

Energy Technology Data Exchange (ETDEWEB)

Kook, Dong Hak; Choi, Heui Joo; Cho, Dong Keun [KAERI, Daejeon (Korea, Republic of)

2010-12-15

Source terms of metal waste comprising a spent fuel assembly are relatively important when the spent fuel is pyroprocessed, because cesium, strontium, and transuranics are not a concern any more in the aspect of source term of permanent disposal. In this study, characteristics of radiation source terms for each structural component in spent fuel assembly was analyzed by using ORIGEN-S with a assumption that 10 metric tons of uranium is pyroprocessed. At first, mass and volume for each structural component of the fuel assembly were calculated in detail. Activation cross section library was generated by using KENO-VI/ORIGEN-S module for top-end piece and bottom-end piece, because those are located at outer core under different neutron spectrum compared to that of inner core. As a result, values of radioactivity, decay heat, and hazard index were reveled to be 1.32x1015 Bequerels, 238 Watts, 4.32x109 m3 water, respectively, at 10 years after discharge. Those values correspond to 0.6 %, 1.1 %, 0.1 %, respectively, compared to that of spent fuel. Inconel 718 grid plate was shown to be the most important component in the all aspects of radioactivity, decay heat, and hazard index although the mass occupies only 1 % of the total. It was also shown that if the Inconel 718 grid plate is managed separately, the radioactivity and hazard index of metal waste could be decreased to 25{approx}50 % and 35{approx}40 %, respectively. As a whole, decay heat of metal waste was shown to be negligible in the aspect of disposal system design, while the radioactivity and hazard index are important

PWR fuel assembly

International Nuclear Information System (INIS)

Yamada, Yuji.

1995-01-01

A lower end plug is secured to a lower end of a thimble tube. A bolt-like thimble screw is screw-coupled and fastened to a female screw disposed to the end plug by way of a bushing screw-coupled to a lower nozzle. Then, the thimble screw and the lower nozzle are welded to secure the thimble tube and the lower nozzle. The lower portion of the bushing extends near the lower surface of the lower nozzle. The extended portion is provided with a recess to which a bolt head of the thimble screw is tightly inserted and a seating-face portion against which a seating-face of the bolt head abuts. Then, the extended portion of the bushing and the lower nozzle are spot-welded on the side of the lower surface of the nozzle, to prevent rotation of the bushing. This can easily prevent the rotation of the bushing after adjustment, to simplify the assembling of the fuel assembly. (I.N.)

Reactivity Impact of Difference of Nuclear Data Library for PWR Fuel Assembly Calculation by Using AEGIS Code

International Nuclear Information System (INIS)

Ohoka, Yasunori; Tatsumi, Masahiro; Sugimura, Naoki; Tabuchi, Masato

2011-01-01

In 2010, the latest version of the Japanese Evaluated Nuclear Data Library (JENDL-4.0) has been released by JAEA. JENDL-4.0 is major update from JENDL- 3.3, and confirmed to give good accuracy by integral test for fission reactor systems such as fast neutron system and thermal neutron system. In this study, we evaluated the reactivity impact due to difference between ENDF/B-VII.0 and JENDL-4.0 for PWR fuel assembly burnup calculation using AEGIS code which has been developed by Nuclear Engineering, Ltd. in cooperation with Nuclear Fuel Industries, Ltd. and Nagoya University

The study on radioactivity reduction of spent PWR cladding hull

International Nuclear Information System (INIS)

Jung, I. H.; Kim, J. H.; Park, C. J.; Jung, Y. H.; Song, K. C.; Lee, J. W.; Park, J. J.; Yang, M. S.

2003-01-01

Hull arising from the spent PWR fuel elements is classified as a high-level radioactive waste. This report describes the radio-chemical characteristics of the hull-from PWR spent fuel of 32,000MWd/tU burn-up and 15 years cooling, discharged from Gori Unit I cycled 4-7-by examination and literature survey. On the basis of the results, a method of degradation to middle and low-level radioactive waste was proposed by dry process such as laser or plasma technique with removing the nuclides deposited on the surface of the hull

Development of an innovative PWR for low cost fuel recycle and waste reduction

International Nuclear Information System (INIS)

Kanagawa, Takashi; Onoue, Masaaki

2001-01-01

In order to bear long-term and stable energy supply, it is important for nuclear power generation to realize establishment of energy security controlling dependence on natural resources and reduction of long-life radioactive wastes such as minor actinide elements (MA) and so on. For this, establishment of fast breeder reproducible on its fuel and of fuel recycling is essential and construction of the fuel recycling capable of repeatedly recycling of plutonium (Pu) and MA with low cost is required. Here were proposed a fuel recycling system combining recycling type PWR with advanced recycling system under development for Na cooling fast breeder reactor as a candidate filling such conditions, to show its characteristics and effects after its introduction. By this system, some facilities to realize flexible and low cost fuel recycling, to reduce longer-life radioactive wastes due to recycling burning of Pu and MA, and to realize an electric power supplying system independent on natural resources due to fuel breeding feature, were shown. (G.K.)

Estimation of mean time to failure of a near surface radioactive waste repository for PWR power stations

International Nuclear Information System (INIS)

Aguiar, Lais A. de; Frutuoso e Melo, P.F.; Alvim, Antonio C.M.

2007-01-01

This work aims at estimating the mean time to failure (MTTF) of each barrier of a near surface radioactive waste repository. It is assumed that surface water infiltrates through the barriers, reaching the matrix where radionuclides are contained, releasing them to the environment. Radioactive wastes considered in this work are low and medium level wastes (produced during operation of a PWR nuclear power station) fixed on cement. The repository consists of 6 saturated porous media barriers (top cover, upper layer, packages, basis, repository walls and geosphere). It has been verified that the mean time to failure (MTTF) of each barrier increases for radionuclides having higher retardation factor (Fr) and also that the MTTF for concrete is larger for Nickel , while for the geosphere, Plutonium gives the largest MTTF. (author)

Analysis of PWR assembly bow

International Nuclear Information System (INIS)

Fetterman, Robert J.; Franceschini, Fausto

2008-01-01

Excessive out of core assembly bow has been observed during refueling outages of certain PWRs. Assembly bow can take on a rather complex S-shape, and in other cases C-shape bow is prevalent. Concerns have been raised regarding the impact of the observed assembly bow on the in-core power distribution and the safety analyses supporting the plant operations. In response to these concerns, Westinghouse has developed a comprehensive analysis process for determining the effects of assembly bow on core power distributions and plant operating margins. This methodology has been applied to a particular reactor as part of an overall safety reanalysis completed in support of plant modifications. This paper provides a brief description of the methods used and a summary of the pertinent results. (authors)

Analysis of PWR assembly bow

Energy Technology Data Exchange (ETDEWEB)

Fetterman, Robert J.; Franceschini, Fausto [Westinghouse Electric Company LLC, Pittsburgh, PA (United States)

2008-07-01

Excessive out of core assembly bow has been observed during refueling outages of certain PWRs. Assembly bow can take on a rather complex S-shape, and in other cases C-shape bow is prevalent. Concerns have been raised regarding the impact of the observed assembly bow on the in-core power distribution and the safety analyses supporting the plant operations. In response to these concerns, Westinghouse has developed a comprehensive analysis process for determining the effects of assembly bow on core power distributions and plant operating margins. This methodology has been applied to a particular reactor as part of an overall safety reanalysis completed in support of plant modifications. This paper provides a brief description of the methods used and a summary of the pertinent results. (authors)

Advanced high conversion PWR: preliminary analysis

International Nuclear Information System (INIS)

Golfier, H.; Bellanger, V.; Bergeron, A.; Dolci, F.; Gastaldi, B.; Koberl, O.; Mignot, G.; Thevenot, C.

2007-01-01

In this paper, physical aspects of a HCPWR (High Conversion Light Water Reactor), which is an innovative PWR fuelled with mixed oxide and having a higher conversion ratio due to a lower moderation ratio. Moderation ratios lower than unity are considered which has led to low moderation PWR fuel assembly designs. The objectives of this parametric study are to define a feasibility area with regard to the following neutronic aspects: moderation ratio, Pu loading, reactor spectrum, irradiation time, and neutronic coefficients. Important thermohydraulic parameters are the pressure drop, the critical heat flux, the maximum temperature in the fuel rod and the pumping power. The thermohydraulic analysis shows that a range of moderation ratios from 0.8 to 1.2 is technically possible. A compromise between improved fuel utilization and research and development effort has been found for the moderation ration of about 1. The parametric study shows that there are 2 ranges of interest for the moderation ratio: -) moderation ratio between 0.8 and 1.2 with reduced fissile heights (> 3 m), hexagonal arrangement fuel assembly and square arrangement fuel assembly are possible; and -) moderation between 0.6 and 0.7 with a modification of the reactor operating conditions (reduction of the primary flow and of the thermal power), the fuel rods could be arranged inside a hexagonal fuel rod assembly. (A.C.)

The application of neural networks for optimization of the configuration of fuel assemblies in PWR reactors

International Nuclear Information System (INIS)

Sadighi, M.; Setayeshi, S.; Salehi, A.A.

2002-01-01

This paper presents a new method to solve the problem of finding the best configuration of fuel assemblies in a PWR (Pressurized Water Reactor) core. Finding an optimum solution requires a huge amount of calculations in classical methods. It has been shown that the application of continuous Hop field neural network accompanied by the Simulated Annealing method to this problem not only reduces the volume of the calculations, but also guarantees finding the best solution. In this study flattening of neutron flux inside the reactor core of Brusher NPP is considered as an objective function. The result shows the optimum core configuration which is in agreement with the pattern proposed by the designer

Design of a PWR for long cycle and direct recycling of spent fuel

Energy Technology Data Exchange (ETDEWEB)

Mohamed, Nader M.A., E-mail: mnader73@yahoo.com

2015-12-15

Highlights: • Single-batch loading PWR with a new fuel assembly for 36 calendar months cycle was designed. • The new fuel assembly is constructed from a number of CANDU fuel bundles. • This design enables to recycle the spent fuel directly in CANDU reactors for high burnup. • Around 56 MWd/kgU burnup is achieved from fuel that has average enrichment of 4.8 w/o U-235 using this strategy. • Safety parameters such as the power distribution and CANDU coolant void reactivity were considered. - Abstract: In a previous work, a new design was proposed for the Pressurized Water Reactor (PWR) fuel assembly for direct use of the PWR spent fuel without processing. The proposed assembly has four zircaloy-4 tubes contains a number of 61-element CANDU fuel bundles (8 bundles per tube) stacked end to end. The space between the tubes contains 44 lower enriched UO{sub 2} fuel rods and 12 guide tubes. In this paper, this assembly is used to build a single batch loading 36-month PWR and the spent CANDU bundles are recycled in the on power refueling CANDU reactors. The Advanced PWR (APWR) is considered as a reference design. The average enrichment in the core is 4.76%w U-235. IFBA and Gd{sub 2}O{sub 3} as burnable poisons are used for controlling the excess reactivity and to flatten the power distribution. The calculations using MCNPX showed that the PWR will discharge the fuel with average burnup of 31.8 MWd/kgU after 1000 effective full power days. Assuming a 95 days plant outage, 36 calendar months can be achieved with a capacity factor of 91.3%. Good power distribution in the core is obtained during the cycle and the required critical boron concentration is less than 1750 ppm. Recycling of the discharged CANDU fuel bundles that represents 85% of the fuel in the assembly, in CANDU-6 or in 700 MWe Advanced CANDU Reactor (ACR-700), an additional burnup of about 31 or 26 MWd/kgU burnup can be achieved, respectively. Averaging the fuel burnup on the all fuel in the PWR

PWR fuel performance and future trend in Japan

International Nuclear Information System (INIS)

Kondo, Y.

1987-01-01

Since the first PWR power plant Mihama Unit 1 initiated its commercial operation in 1970, Japanese utilities and manufacturers have expended much of their resources and efforts to improve PWR technology. The results are already seen in significantly improved performance of 16 PWR plants now in operation. Mitsubishi Heavy Industries Ltd. (MHI) has been supplying them with nuclear fuel assemblies, which are over 5700. As the reliability of the current design fuel has been achieved, the direction of R and D on nuclear fuel has changed to make nuclear power more competitive to the other power generation methods. The most important R and D targets are the burnup extension, Gd contained fuel, Pu utilizatoin and the load follow capacility. (author)

PWR internals segmentation and packaging experience in the U.S

International Nuclear Information System (INIS)

Kreitman, P.J.

2008-01-01

Seven commercial nuclear power plants of the Pressurized Water Reactor (PWR) design have been permanently shut down in the US to date. Six of these plants have been decommissioned using dismantling methods. The remaining plant, Indian Point 1, located in Buchanan, NY, has been placed in Safe Storage. Of the six dismantled plants, five underwent extensive segmentation, separation, and packaging of their internal components to allow removal and disposal of the reactor vessel assembly. Only the Trojan Plant in Portland, Oregon, was able to ship the reactor vessel assembly with its internals intact to the final disposal site near Richland, Washington. An important part of the planning for the upcoming decommissioning of similar plants in Europe such as Chooz A in France and Zorita in Spain will be to study the lessons learned from the US efforts and apply the best practices to future projects. This paper will chronicle the evolution of the reactor internals segmentation and packaging process to date, including the planning, methodology, equipment, waste management, and packaging strategy. (author)

Feasibility study on thermal-hydraulic design of reduced-moderation PWR-type core

International Nuclear Information System (INIS)

Yoshida, Hiroyuki; Ohnuki, Akira; Akimoto, Hajime

2000-03-01

At JAERI, a conceptual study on reduced-moderation water reactor (RMWR) has been performed as one of the advanced reactor system which is designed so as to realize the conversion ratio more than unity. In this reactor concept, the gap spacing between the fuel rods is remarkably narrower than in a reactor currently operated. Therefore, an evaluation of the core thermal margin becomes very important in the design of the RMWR. In this study, we have performed a feasibility evaluation on thermal-hydraulic design of RM-PWR type core (core thermal output: 2900 MWt, Rod gaps: 1 mm). In RM-PWR core, seed and blanket regions are exist. In the blanket region, power density is lower than that of the seed region. Then, evaluation was performed under setting a channel box to each fuel assembly in order to adjust the flow rate in each assembly, because it is possible that the coolant boils in the seed region. In the feasibility evaluations, subchannel code COBRA-IV-I was used in combination with KfK DNB (departure nucleate boiling) correlation. When coolant mass flow rate to the blanket fuel assembly is reduced by 40%, and that to the seed fuel assembly is increased, coolant boiling is not occurred in the assembly region calculation. Provided that the channel boxes to the blanket fuel assembly are set up and coolant mass flow rate to the blanket fuel assembly is reduced by 40%, it is confirmed by the whole core calculation that the boiling of the coolant is not occurred and the RM-PWR core is feasible. (author)

A classification scheme for LWR fuel assemblies

Energy Technology Data Exchange (ETDEWEB)

Moore, R.S.; Williamson, D.A.; Notz, K.J.

1988-11-01

With over 100 light water nuclear reactors operating nationwide, representing designs by four primary vendors, and with reload fuel manufactured by these vendors and additional suppliers, a wide variety of fuel assembly types are in existence. At Oak Ridge National Laboratory, both the Systems Integration Program and the Characteristics Data Base project required a classification scheme for these fuels. This scheme can be applied to other areas and is expected to be of value to many Office of Civilian Radioactive Waste Management programs. To develop the classification scheme, extensive information on the fuel assemblies that have been and are being manufactured by the various nuclear fuel vendors was compiled, reviewed, and evaluated. It was determined that it is possible to characterize assemblies in a systematic manner, using a combination of physical factors. A two-stage scheme was developed consisting of 79 assembly types, which are grouped into 22 assembly classes. The assembly classes are determined by the general design of the reactor cores in which the assemblies are, or were, used. The general BWR and PWR classes are divided differently but both are based on reactor core configuration. 2 refs., 15 tabs.

A classification scheme for LWR fuel assemblies

International Nuclear Information System (INIS)

Moore, R.S.; Williamson, D.A.; Notz, K.J.

1988-11-01

With over 100 light water nuclear reactors operating nationwide, representing designs by four primary vendors, and with reload fuel manufactured by these vendors and additional suppliers, a wide variety of fuel assembly types are in existence. At Oak Ridge National Laboratory, both the Systems Integration Program and the Characteristics Data Base project required a classification scheme for these fuels. This scheme can be applied to other areas and is expected to be of value to many Office of Civilian Radioactive Waste Management programs. To develop the classification scheme, extensive information on the fuel assemblies that have been and are being manufactured by the various nuclear fuel vendors was compiled, reviewed, and evaluated. It was determined that it is possible to characterize assemblies in a systematic manner, using a combination of physical factors. A two-stage scheme was developed consisting of 79 assembly types, which are grouped into 22 assembly classes. The assembly classes are determined by the general design of the reactor cores in which the assemblies are, or were, used. The general BWR and PWR classes are divided differently but both are based on reactor core configuration. 2 refs., 15 tabs

Proposal for a advanced PWR core with adequate characteristics for passive safety concept

International Nuclear Information System (INIS)

Perrotta, Jose Augusto

1999-01-01

This work presents a discussion upon the suitable from an advanced PWR core, classified by the EPRI as 'Passive PWR' (advanced reactor with passive safety concept to power plants with less than 600 MW electrical power). The discussion upon the type of core is based on nuclear fuel engineering concepts. Discussion is made on type of fuel materials, structural materials, geometric shapes and manufacturing process that are suitable to produce fuel assemblies which give good performance for this type of reactors. The analysis is guided by the EPRI requirements for Advanced Light Water Reactor (ALWR). By means of comparison, the analysis were done to Angra 1 (old type of 600 MWe PWR class), and the design of the Westinghouse Advanced PWR-AP600. It was verified as a conclusion of this work that the modern PWR fuels are suitable for advanced PWR's Nevertheless, this work presents a technical alternative to this kind of fuel, still using UO 2 as fuel, but changing its cylindrical form of pellets and pin type fuel element to plane shape pallets and plate type fuel element. This is not a novelty fuel, since it was used in the 50's at Shippingport Reactor and as an advanced version by CEA of France in the 70's. In this work it is proposed a new mechanical assembly design for this fuel, which can give adequate safety and operational performance to the core of a 'Passive PWR'. (author)

An analytical model for the prediction of fluid-elastic forces in a rod bundle subjected to axial flow: theory, experimental validation and application to PWR fuel assemblies

International Nuclear Information System (INIS)

Beaud, F.

1997-01-01

A model predicting the fluid-elastic forces in a bundle of circular cylinders subjected to axial flow is presented in this paper. Whereas previously published models were limited to circular flow channel, the present one allows to take a rectangular flow external boundary into account. For that purpose, an original approach is derived from the standard method of images. This model will eventually be used to predict the fluid-structure coupling between the flow of primary coolant and a fuel assemblies in PWR nuclear reactors. It is indeed of major importance since the flow is shown to induce quite high damping and could therefore mitigate the incidence of an external load like a seismic excitation on the dynamics of the assemblies. The proposed model is validated on two cases from the literature but still needs further comparisons with the experiments being currently carried out on the EDF set-up. The flow has been shown to induce an approximate 12% damping on a PWR fuel assembly, at nominal reactor conditions. The possible grid effect on the fluid-structure coupling has been neglected so far but will soon be investigated at EDF. (author)

Development of a reference spent fuel library of 17x17 PWR fuel assemblies

International Nuclear Information System (INIS)

Rossa, Riccardo; Borella, Alessandro; Van der Meer, Klaas

2013-01-01

One of the most common ways to investigate new Non-Destructive Assays (NDA) for the spent fuel assemblies are Monte Carlo simulations. In order to build realistic models the user must define in an accurate way the material compositions and the source terms in the system. This information can be obtained using burnup codes such as ORIGEN-ARP and ALEPH2.2, developed at SCK-CEN. These software applications allow the user to select the irradiation history of the fuel assembly and to calculate the corresponding isotopic composition and neutron/gamma emissions as a function of time. In the framework of the development of an innovative NDA for spent fuel verifications, SCK•CEN built an extensive fuel library for 17x17 PWR assemblies, using both ORIGEN-ARP and ALEPH2.2. The parameters considered in the calculations were initial enrichment, discharge burnup, and cooling time. The combination of these variables allows to obtain more than 1500 test cases. Considering the broad range of the parameters, the fuel library can be used for other purposes apart from spent fuel verifications, for instance for the direct disposal in geological repositories. In addition to the isotopic composition of the spent fuel, the neutron and photon emissions were also calculated and compared between the two codes. The comparison of the isotopic composition showed a good agreement between the codes for most of the relevant isotopes in the spent fuel. However, specific isotopes as well as neutron and gamma spectra still need to be investigated in detail.

Evaluation of the presence of a burnable absorber in an assembly 3x3 type PWR

International Nuclear Information System (INIS)

Martinez F, M. A.; Del Valle G, E.; Alonso V, G.

2008-01-01

In the present work the effect is evaluated that causes the presence of a burnable absorber in an adjustment of rods of 3x3 of a fuel assembly type PWR using CASMO-4 code, when comparing the infinite multiplication factor and some average cross sections by means of codes MCNP-4A, CASMO-3 and HELIOS. For this evaluation two cases are evaluated: first consists of an adjustment of rods of 3x3 full completely of fuel and the second consists of a central rod full with a burnable absorber type wet annular burnable absorber (WABA) and the remaining full fuel rods. In both cases the enrichment of the fissile isotopes is varied, for two types of fuel, MOX degree armament and UO 2 . (Author)

Criticality calculations of a generic fuel container for fuel assemblies PWR, by means of the code MCNP; Calculos de criticidad de un contenedor de combustible generico para ensambles combustibles PWR, mediante el codigo MCNP

Energy Technology Data Exchange (ETDEWEB)

Vargas E, S.; Esquivel E, J.; Ramirez S, J. R., E-mail: samuel.vargas@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

2013-10-15

The purpose of the concept of burned consideration (Burn-up credit) is determining the capacity of the calculation codes, as well as of the nuclear data associates to predict the isotopic composition and the corresponding neutrons effective multiplication factor in a generic container of spent fuel during some time of relevant storage. The present work has as objective determining this capacity of the calculation code MCNP in the prediction of the neutrons effective multiplication factor for a fuel assemblies arrangement type PWR inside a container of generic storage. The calculations are divided in two parts, the first, in the decay calculations with specified nuclide concentrations by the reference for a pressure water reactor (PWR) with enriched fuel to 4.5% and a discharge burned of 50 GW d/Mtu. The second, in criticality calculations with isotopic compositions dependent of the time for actinides and important fission products, taking 30 time steps, for two actinide groups and fission products. (Author)

Design of Evaporator for Liquid Radioactive Waste Treatment-NPP 1000 MW, PWR

International Nuclear Information System (INIS)

Mulyono Daryoko

2007-01-01

The evaporator for liquid radioactive waste treatment of 1000 MW NPP-PWR has been designed. The basic calculate of this design was capacity 7000 l/hr, which 5 mg/l solid content. The system used was superheated steam 3.4 atmosphere, 281°F. The data required from design of evaporator are evaporator part (heat exchanger): diameter of shell is 33 inch (82.50 cm), nominal diameter tube is 1.5 inch (3.75 cm), number of tube is 215, tube arrangement triangular pitch is 1 inch pitch, height 600 cm; Mist separator: diameter is 200 inch (500 cm), height 600 inch (1500 cm); Condenser: diameter of shell is 33 inch (82.50 cm), nominal diameter tube is 1.5 inch (3.75 cm), number of tube is 215, tube arrangement triangular pitch is 1 inch pitch, height 600 cm. (author)

In-plant test and evaluation of the neutron collar for verification of PWR fuel assemblies at Resende, Brazil

International Nuclear Information System (INIS)

Menlove, H.O.; Marzo, M.A.S.; de Almeida, S.G.; de Almeida, M.C.; Moitta, L.P.M.; Conti, L.F.; de Paiva, J.R.T.

1985-11-01

The neutron-coincidence collar has been evaluated for the measurement of pressurized-water reactor (PWR) fuel assemblies at the Fabrica de Elementos Combustiveis plant in Resende, Brazil. This evaluation was part of the cooperative-bilateral-safeguards technical-exchange program between the United States and Brazil. The neutron collar measures the 235 U content per unit length of full fuel assemblies using neutron interrogation and coincidence counting. The 238 U content is measured in the passive mode without the AmLi neutron-interrogation source. The extended evaluation took place over a period of 6 months with both scanning and single-zone measurements. The results of the tests gave a coincidence-response standard deviation of 0.7% (sigma = 1.49% for mass) for the active case and 2.5% for the passive case in 1000-s measurement times. The length measurement in the scanning mode was accurate to 0.77%. The accuracies of different calibration methods were evaluated and compared

Status and future perspectives of PWR and comparing views on WWER fuel technology

International Nuclear Information System (INIS)

Weidinger, H.

2003-01-01

The main purpose of this paper is to give an overview on status and future perspectives of the Western PWR fuel technology. For easer understanding and correlating, some comparing views to the WWER fuel technology are provided. This overview of the PWR fuel technology of course can not go into the details of the today used designs of fuel, fuel rods and fuel assemblies. However, it tries to describe the today achieved capability of PWR fuel technology with regard to reliability, efficiency and safety

Reference concepts for the final disposal of LWR spent fuel and other high activity wastes in Spain

International Nuclear Information System (INIS)

Huertas, F.; Ulibarri, A.

1993-01-01

Studies over the last three years have been recently concluded with the selection of a reference repository concept for the final disposal of spent fuel and other high activity wastes in deep geological formations. Two non-site specific preliminary designs, at a conceptual level, have been developed; one considers granite as the host rock and the other rock salt formations. The Spanish General Radioactive Waste Program also considers clay as a potential host rock for HLW deep disposal; conceptualization for a deep repository in clay is in the initial phase of development. The salt repository concept contemplates the disposal of the HLW in self-shielding casks emplaced in the drifts of an underground facility, excavated at a depth of 850 m in a bedded salt formation. The Custos Type I(7) cask admits up to seven intact PWR fuel assemblies or 21 of BWR type. The final repository facilities are planned to accept a total of 20,000 fuel assemblies (PWR and BWR) and 50 vitrified waste canisters over a period of 25 years. The total space needed for the surface facilities amounts to 322,000 m 2 , including the rock salt dump. The space required for the underground facilities amounts to 1.2 km 2 , approximately. The granite repository concept contemplates the disposal of the HLW in carbon steel canisters, embedded in a 0.75 m thick buffer of swelling smectite clay, in the drifts of an underground facility, excavated at a depth of 55 m in granite. Each canister can host 3 PWR or 9 BWR fuel assemblies. For this concept the total number of canisters needed amounts to 4,860. The space required for the surface and underground facilities is similar to that of the salt concept. The technical principles and criteria used for the design are discussed, and a description of the repository concept is presented

AREVA modeling and predictive capacities to support PWR fuel assembly upgrading

International Nuclear Information System (INIS)

Canat, J. N.; Mollard, P.; Gentet, G.; Uyeda, G.

2008-01-01

optimization. It explains how they have supported AREVA in performing a wide ranging review of the various components resulting from the technologies acquired after the merging of FRAMATOME with Siemens Nuclear activities (now resulting in AREVA NP): AFA 3G TM , HTP TM and Mark B TM . Today, AREVA offers to each reactor worldwide the best suited fuel assembly, fully assessed and featuring upgraded components issued from well proven technologies, such as AGORA fuel assemblies or other very advanced versions of fuel assemblies. In all areas of fuel design, computational codes, methods and modeling have improved. The paper details the main progress achieved in a variety of fields. Special attention will be paid to improvements performed in the thermal hydraulics area where the Computational Fluid Dynamics STAR CD tool has been used in several Fuel Assembly design and development applications. This progress was made possible by recently available computer hardware, allowing cost effective and easy access of parallel computing in cluster arrays. Specific applications such as the optimization of the vane shape of PWR grids for higher DNB performance, the evaluation of pressure loss coefficients for complex components such as the anti debris bottom nozzle, computation of the flow velocity distribution and consequent fuel rod vibration regime will be detailed. As for fuel rod design, 3 D modeling of the PCI phenomenon provides a basis for improvements of industrial 1 D predictive tools with a better level of accuracy in discriminating hardware solutions. The developments of the next product generations are reaping the benefits of all these improvements, paying off in optimized designs and upgraded performance and robustness levels, for the final benefit of the utilities, especially with the prospect of fuel supply to the forthcoming Generation III reactors

SACHET, Dynamic Fission Products Inventory in PWR Multiple Compartment System

International Nuclear Information System (INIS)

Kodaira, Hideki

1990-01-01

1 - Description of program or function: SACHET evaluates the dynamic fission product inventories in the multiple compartment system of pressurized water reactor (PWR) plants. 2 - Method of solution: SACHET utilizes a matrix of fission product core inventory which is previously calculated by the ORIGEN code. 3 - Restrictions on the complexity of the problem: Liquid wastes such as chemical waste and detergent waste are not included

Minor actinide transmutation on PWR burnable poison rods

International Nuclear Information System (INIS)

Hu, Wenchao; Liu, Bin; Ouyang, Xiaoping; Tu, Jing; Liu, Fang; Huang, Liming; Fu, Juan; Meng, Haiyan

2015-01-01

Highlights: • Key issues associated with MA transmutation are the appropriate loading pattern. • Commercial PWRs are the only choice to transmute MAs in large scale currently. • Considerable amount of MA can be loaded to PWR without disturbing k eff markedly. • Loading MA to PWR burnable poison rods for transmutation is an optimal loading pattern. - Abstract: Minor actinides are the primary contributors to long term radiotoxicity in spent fuel. The majority of commercial reactors in operation in the world are PWRs, so to study the minor actinide transmutation characteristics in the PWRs and ultimately realize the successful minor actinide transmutation in PWRs are crucial problem in the area of the nuclear waste disposal. The key issues associated with the minor actinide transmutation are the appropriate loading patterns when introducing minor actinides to the PWR core. We study two different minor actinide transmutation materials loading patterns on the PWR burnable poison rods, one is to coat a thin layer of minor actinide in the water gap between the zircaloy cladding and the stainless steel which is filled with water, another one is that minor actinides substitute for burnable poison directly within burnable poison rods. Simulation calculation indicates that the two loading patterns can load approximately equivalent to 5–6 PWR annual minor actinide yields without disturbing the PWR k eff markedly. The PWR k eff can return criticality again by slightly reducing the boric acid concentration in the coolant of PWR or removing some burnable poison rods without coating the minor actinide transmutation materials from PWR core. In other words, loading minor actinide transmutation material to PWR does not consume extra neutron, minor actinide just consumes the neutrons which absorbed by the removed control poisons. Both minor actinide loading patterns are technically feasible; most importantly do not need to modify the configuration of the PWR core and

Analysis of dynamic behavior of a PWR utilizing the computer program SARDAN 2

International Nuclear Information System (INIS)

Pessanha, J.A.O.

1982-07-01

In the design of a PWR nuclear plant it is necessary to verify if the design limits are respected, even under abnormal operation condition. An evolution of SARDAN code, developed to simulate transients in PWR, are presented. The new aspects incorporeted in SARDAN 2 are: the fuel ROD analysis in finite-diference, an open channel model for the critic subchannel analysis and the introduction of a simplified model for the automatic control system. The program has been tested in accident condition II, in special, uncontrolled ROD cluster assembly bank withoraw, dropped full-length assembly group, uncontrolled Boron dilution, and the results obtained were considered satisfactory. (Author) [pt

Validation of gadolinium burnout using PWR benchmark specification

Energy Technology Data Exchange (ETDEWEB)

Oettingen, Mikołaj, E-mail: moettin@agh.edu.pl; Cetnar, Jerzy, E-mail: cetnar@mail.ftj.agh.edu.pl

2014-07-01

Graphical abstract: - Highlights: • We present methodology for validation of gadolinium burnout in PWR. • We model 17 × 17 PWR fuel assembly using MCB code. • We demonstrate C/E ratios of measured and calculated concentrations of Gd isotopes. • The C/E for Gd154, Gd156, Gd157, Gd158 and Gd160 shows good agreement of ±10%. • The C/E for Gd152 and Gd155 shows poor agreement below ±10%. - Abstract: The paper presents comparative analysis of measured and calculated concentrations of gadolinium isotopes in spent nuclear fuel from the Japanese Ohi-2 PWR. The irradiation of the 17 × 17 fuel assembly containing pure uranium and gadolinia bearing fuel pins was numerically reconstructed using the Monte Carlo Continuous Energy Burnup Code – MCB. The reference concentrations of gadolinium isotopes were measured in early 1990s at Japan Atomic Energy Research Institute. It seems that the measured concentrations were never used for validation of gadolinium burnout. In our study we fill this gap and assess quality of both: applied numerical methodology and experimental data. Additionally we show time evolutions of infinite neutron multiplication factor K{sub inf}, FIMA burnup, U235 and Gd155–Gd158. Gadolinium-based materials are commonly used in thermal reactors as burnable absorbers due to large neutron absorption cross-section of Gd155 and Gd157.

Techniques and devices developed by the CEA for hot cell and in-situ examinations of PWR components and PWR fuel assembliess after irradiation

International Nuclear Information System (INIS)

Van Craeynest, J.C.; Leseur, A.; Lhermenier, A.; Cytermann, R.

1981-11-01

Within the framework of the electro-nuclear development of the PWR system, the CEA has provided itself with facilities for developing techniques for analyzing assemblies, pins and fuels. These are examinations and tests on irradiated heads and assemblies with the aid of the Fuel Examination Module (FEM), of machining of assemblies and examinations in the Celimene hot laboratory or detailed examinations and analyses on fuel elements using eddy currents, the electronic microprobe and the Fisher ''permeascope'' which enables the outline of the oxide coat present on the cladding to be followed [fr

Comparison of PWR-IMF and FR fuel cycles

International Nuclear Information System (INIS)

Darilek, Petr; Zajac, Radoslav; Breza, Juraj; Necas, Vladimir

2007-01-01

The paper gives a comparison of PWR (Russia origin VVER-440) cycle with improved micro-heterogeneous inert matrix fuel assemblies and FR cycle. Micro-heterogeneous combined assembly contains transmutation pins with Pu and MAs from burned uranium reprocessing and standard uranium pins. Cycle analyses were performed by HELIOS spectral code and SCALE code system. Comparison is based on fuel cycle indicators, used in the project RED-IMPACT - part of EU FP6. Advantages of both closed cycles are pointed out. (authors)

Study on Reactor Physics Characteristic of the PWR Core Using UO2

International Nuclear Information System (INIS)

Tukiran Surbakti

2009-01-01

Study on reactor physics characteristic of the PWR core using UO 2 fuel it is necessary to be done to know the characteristic of geometry, condition and configuration of pin cell in the fuel assembly Because the geometry, configuration and condition of the pin cell in fuel core determine the loading strategy of in-core fuel management Calculation of k e ff is a part of the neutronic core parameter calculation to know the reactor physics characteristic. Generally, core calculation is done using computer code starts from modelling one unit fuel lattice cell, fuel assembly, reflector, irradiation facility and until core reactor. In this research, the modelling of pin cell and fuel assembly of the PWR 17 ×17 is done homogeneously. Calculation of the k-eff is done with variation of the fuel volume fraction, fuel pin diameter, fuel enrichment. The calculation is using by NITAWL and CENTRM, and then the results will be compared to KENOVI code. The result showed that the value of k e ff for pin cell and fuel assembly PWR 17 ×17 is not different significantly with homogenous and heterogenous models. The results for fuel volume fraction of 0.5; rod pitch 1.26 cm and fuel pin diameter of 9.6 mm is critical with burn up of 35,0 GWd/t. The modeling and calculation method accurately is needed to calculation the core physic parameter, but sometimes, it is needed along time to calculate one model. (author)

Dry Ice Blast Decontamination to in-service equipment in Japanese PWR plant

International Nuclear Information System (INIS)

2016-01-01

MHI had developed several mechanical decontamination methods. Mechanical decontamination is beneficial when it is applied to equipment whose surface is narrow. Especially in terms of secondary waste reduction, MHI started the study of application of Dry Ice Blast Decontamination to actual PWR plant. This paper provides an introduction to Dry Ice Blast Decontamination principle, its system and actual application result to PWR plant. (J.P.N.)

Effects of Burnable Absorbers on PWR Spent Nuclear Fuel

International Nuclear Information System (INIS)

O'Leary, P.M.; Pitts, M.L.

2000-01-01

Burnup credit is an ongoing issue in designing and licensing transportation and storage casks for spent nuclear fuel (SNF). To address this issue, in July 1999, the U.S. Nuclear Regulatory Commission (NRC), Spent Fuel Project Office, issued Interim Staff Guidance-8 (ISG-8), Revision 1 allowing limited burnup credit for pressurized water reactor (PWR) spent nuclear fuel (SNF) to be used in transport and storage casks. However, one of the key limitations for a licensing basis analysis as stipulated in ISG-8, Revision 1 is that ''burnup credit is restricted to intact fuel assemblies that have not used burnable absorbers''. Because many PWR fuel designs have incorporated burnable-absorber rods for more than twenty years, this restriction places an unnecessary burden on the commercial nuclear power industry. This paper summarizes the effects of in-reactor irradiation on the isotopic inventory of PWR fuels containing different types of integral burnable absorbers (BAs). The work presented is illustrative and intended to represent typical magnitudes of the reactivity effects from depleting PWR fuel with different types of burnable absorbers

Preliminary neutronics calculation of fusion-fission hybrid reactor breeding spent fuel assembly

International Nuclear Information System (INIS)

Ma Xubo; Chen Yixue; Gao Bin

2013-01-01

The possibility of using the fusion-fission hybrid reactor breeding spent fuel in PWR was preliminarily studied in this paper. According to the fusion-fission hybrid reactor breeding spent fuel characteristics, PWR assembly including fusion-fission hybrid reactor breeding spent fuel was designed. The parameters such as fuel temperature coefficient, moderator temperature coefficient and their variation were investigated. Results show that the neutron properties of uranium-based assembly and hybrid reactor breeding spent fuel assembly are similar. The design of this paper has a smaller uniformity coefficient of power at the same fissile isotope mass percentage. The results will provide technical support for the future fusion-fission hybrid reactor and PWR combined with cycle system. (authors)

Status of developing advanced PWR in Japan

International Nuclear Information System (INIS)

Iida, Yotaro

1982-01-01

During past eleven years since the first PWR power plant, Mihama Unit 1 of Kansai Electric Power Co., started the commercial operation in 1970, Mitsubishi Heavy Industries has endeavored to improve PWR technologies on the basis of the advice from electric power companies and the technical information to overcome difficulties in PWR power plants. Now, the main objective is to improve the overall plant performance, and the rate of operation of Japanese PWR power plants has significantly risen. The improvement of the reliability, the shortening of regular inspection period and the reduction of radioactive waste handling were attempted. In view of the satisfactory operational experience of Westinghouse type PWRs, the basic reactor concept has not been changed so far. Mitsubishi and Westinghouse reached basic agreement in August, 1981, to develop a spectral shift type large capacity reactor as the advanced PWRs for Japan. This type of PWRs hab higher degree of freedom for extended fuel cycle operation and enhances the advantage of entire fuel cycle economy, particularly the significant reduction of uranium use. The improved neutron economy is attainable by reducing neutron loss, and the core design with low power density and the economical use of plutonium are advantageous for the fuel cycle economy. (Kako, I.)

Design study on PWR-type reduced-moderation light water core. Investigation of core adopting seed-blanket fuel assemblies

Energy Technology Data Exchange (ETDEWEB)

Shimada, Shoichiro; Kugo, Teruhiko; Okubo, Tsutomu; Iwamura, Takamichi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2003-03-01

As a part of the design study on PWR-type Reduced-Moderation Water Reactors (RMWRs), a light water cooled core with the seed-blanket type fuel assemblies has been investigated. An assembly with seed of 13 layers and blanket of 5 layers was selected by optimization calculations. The core was composed with the 163 assemblies. The following results were obtained by burn-up calculations with the MVP-BURN code; The cycle length is 15 months by 3-batch refueling. The discharge burn-up including the inner blanket is about 25 GWd/t. The conversion ratio is about 1.0. The void reactivity coefficient is about-26.1 pcm/%void at BOC and -21.7pcm%void at EOC. About 10% of MA makes conversion ratio decrease about 0.05 to obtain the same burn-up. The void reactivity coefficient increased significantly and it is necessary to reduce it. FP amount corresponding to about 2 % of total plutonium weight makes reactivity decrease about 0.5 %{delta}k/k and void reactivity coefficient increase, however these changes are within the design margins. Capability of multi-recycling of plutonium was confirmed, using discharged plutonium for 4 cycles, if fissile plutonium of 15.5wt% is used. The conversion ratio increases by about 0.026 with recycling. However, void reactivity coefficient increases and some effort to obtain negative void reactivity coefficient is necessary. (author)

Radionuclide release from PWR spent fuel specimens with induced cladding defects

International Nuclear Information System (INIS)

Wilson, C.N.; Oversby, V.M.

1984-03-01

Radionuclide releases from pressurized water reactor (PWR) spent fuel rod specimens containing various artificially induced cladding defects were compared by leach testing. The study was conducted in support of the Nevada Nuclear Waste Storage Investigations (NNWSI) Waste Package Task to evaluate the effectiveness of failed cladding as a barrier to radionuclide release. Test description and results are presented

Scope and procedures of fuel management for PWR nuclear power plant

International Nuclear Information System (INIS)

Yao Zenghua

1997-01-01

The fuel management scope of PWR nuclear power plant includes nuclear fuel purchase and spent fuel disposal, ex-core fuel management, in-core fuel management, core management and fuel assembly behavior follow up. A suit of complete and efficient fuel management procedures have to be created to ensure the quality and efficiency of fuel management work. The hierarchy of fuel management procedure is divided into four levels: main procedure, administration procedure, implement procedure and technic procedure. A brief introduction to the fuel management scope and procedures of PWR nuclear power plant are given

Use of standard spectra for the short life radionuclides and ratios for long life radionuclides in the wastes of EDF PWR type reactors

International Nuclear Information System (INIS)

Lantes, B.; Bienvenu, Ph.

2001-01-01

This paper presents the type of declaration of radioactivity in the wastes of PWR type reactors park. Particularly, it insists on the justification of use of spectra for the declaration of short live radionuclides. It tackles the important developments of methods and measures of radiochemical analysis made by the Cea in order to determine the ratios to declare the long life radioisotopes. (N.C.)

Full scale tests on remote handled FFTF fuel assembly waste handling and packaging

International Nuclear Information System (INIS)

Allen, C.R.; Cash, R.J.; Dawson, S.A.; Strode, J.N.

1986-01-01

Handling and packaging of remote handled, high activity solid waste fuel assembly hardware components from spent FFTF reactor fuel assemblies have been evaluated using full scale components. The demonstration was performed using FFTF fuel assembly components and simulated components which were handled remotely using electromechanical manipulators, shielding walls, master slave manipulators, specially designed grapples, and remote TV viewing. The testing and evaluation included handling, packaging for current and conceptual shipping containers, and the effects of volume reduction on packing efficiency and shielding requirements. Effects of waste segregation into transuranic (TRU) and non-transuranic fractions also are discussed

Reverse depletion method for PWR core reload design

International Nuclear Information System (INIS)

Downar, T.J.; Kim, Y.J.

1985-01-01

Low-leakage fuel management is currently practiced in over half of all pressurized water reactor (PWR) cores. Prospects for even greater use of in-board fresh fuel loading are good as utilities seek to reduce core vessel fluence, mitigate pressurized thermal shock concerns, and extend vessel lifetime. Consequently, large numbers of burnable poison (BP) pins are being used to control the power peaking at the in-board fresh fuel positions. This has presented an additional complexity to the core reload design problem. In addition to determining the best location of each assembly in the core, the designer must concurrently determine the distribution of BP pins in the fresh fuel. A procedure was developed that utilizes the well-known Haling depletion to achieve an end-of-cycle (EOC) core state where the assembly pattern is configured in the absence of all control poison. This effectively separates the assembly assignment and BP distribution problems. Once an acceptable pattern at EOC is configured, the burnable and soluble poison required to control the power and core excess reactivity are solved for as unknown variables while depleting the cycle in reverse from the EOC exposure distribution to the beginning of cycle. The methods developed were implemented in an approved light water reactor licensing code to ensure the validity of the results obtained and provide for the maximum utility to PWR core reload design

Radionuclide release from PWR spent fuel specimens with induced cladding defects

International Nuclear Information System (INIS)

Wilson, C.N.; Oversby, V.M.

1984-03-01

Radionuclide releases from pressurized water reactor (PWR) spent fuel rod specimens containing various artificially induced cladding defects were compared by leach testing. The study was conducted in support of the Nevada Nuclear Waste Storage Investigations (NNWSI) Waste Package Task to evaluate the effectiveness of failed cladding as a barrier to radionuclide release. Test description and results are presented. 6 references, 4 figures

New methodology for the analysis of the quality controls of ENUSA on PWR components; Nueva metodologia para el analisis de los controles de calidad de ENUSA sobre los componentes PWR

Energy Technology Data Exchange (ETDEWEB)

Munoz, A.; Navas, I. de; Prieto, M.

2012-07-01

For the manufacture of PWR fuel assemblies, ENUSA receives the components of Westinghouse, who ensures its quality. However, ENUSA carried out on these components various quality controls that increase reliability and give added value.

Advancing PWR fuel to meet customer needs

Energy Technology Data Exchange (ETDEWEB)

Kramer, F W

1987-03-01

Since the introduction of the Optimized Fuel Assembly (OFA) for PWRs in the late 1970s, Westinghouse has continued to work with the utility customers to identify the greatest needs for further advance in fuel performance and reliability. The major customer requirements include longer fuel cycle at lower costs, increased fuel discharge burn-up, enhanced operating flexibility, all accompanied by even greater reliability. In response to these needs, Westinghouse developed Vantage 5 PWR fuel. To optimize reactor operations, Vantage 5 fuel features distinct advantages: integral fuel burnable absorbers, axial and radial blankets, intermediate flow mixers, a removable top nozzle, and assembly modifications to accommodate increased discharge burn-up.

LES analysis of the flow in a simplified PWR assembly with mixing grid

International Nuclear Information System (INIS)

Bieder, Ulrich; Fauchet, Gauthier; Falk, Francois

2014-01-01

The flow in fuel assemblies of Pressurized Water Reactors (PWR) with mixing grids has been analysed with Computational Fluid Dynamics (CFD) by numerous authors. The comparisons between calculation and experiment are mostly focused on the flow in the near wake of the mixing grid, i.e. on the flow in the first 5 to 10 hydraulic diameters (dh) downstream of the grid. In the study presented here, the comparison between the measurements in the AGATE facility (5 * 5 tube bundle) and Trio-U calculations is done for the whole distance between two successive mixing grids that is up to about 50 d h downstream of the grid. The AGATE experiments have originally not been designed for CFD validation but to characterize different types of mixing grids. Nevertheless, the quality of the experimental data allows the quantitative comparison between measurement and calculation. The conclusions of the comparison are summarized below: Linear turbulent viscosity models seem to work rather well as long as the cross flow velocity in the rod gaps is advection controlled, that is directly downstream of the mixing grid, Further downstream, when the cross flow velocity is reduced and anisotropic turbulence becomes a more and more important mixing phenomena, linear viscosity models can fail, The mixing grid affects the cross flow velocity up to the successive grid. The flow in fuel assemblies is never similar to that in undisturbed rod bundles. The test section of the AGATE facility has been discretized on 300 million control volumes by using a staggered grid approach on tetrahedral meshes. 20 days of CPU on 4600 cores of the High Performance Computer (HPC) cluster CURIE of the Centre de Calcul, Recherche et Technologie (CCRT) were necessary to converge the statistics of the turbulent fluctuations, completely converge the mean velocity and incompletely converge the RMS of the turbulent fluctuations. (authors)

Destruction of plutonium using non-uranium fuels in pressurized water reactor peripheral assemblies

International Nuclear Information System (INIS)

Chodak, P. III

1996-05-01

This thesis examines and confirms the feasibility of using non-uranium fuel in a pressurized water reactor (PWR) radial blanket to eliminate plutonium of both weapons and civilian origin. In the equilibrium cycle, the periphery of the PWR is loaded with alternating fresh and once burned non-uranium fuel assemblies, with the interior of the core comprised of conventional three batch UO 2 assemblies. Plutonium throughput is such that there is no net plutonium production: production in the interior is offset by destruction in the periphery. Using this approach a 50 MT WGPu inventory could be eliminated in approximately 400 reactor years of operation. Assuming all other existing constraints were removed, the 72 operating US PWRs could disposition 50 MT of WGPu in 5.6 years. Use of a low fissile loading plutonium-erbium inert-oxide-matrix composition in the peripheral assemblies essentially destroys 100% of the 239 Pu and ≥90% total Pu over two 18 month fuel cycles. Core radial power peaking, reactivity vs EFPD profiles and core average reactivity coefficients were found to be comparable to standard PWR values. Hence, minimal impact on reload licensing is anticipated. Examination of potential candidate fuel matrices based on the existing experience base and thermo-physical properties resulted in the recommendation of three inert fuel matrix compositions for further study: zirconia, alumina and TRISO particle fuels. Objective metrics for quantifying the inherent proliferation resistance of plutonium host waste and fuel forms are proposed and were applied to compare the proposed spent WGPu non-uranium fuel to spent WGPu MOX fuels and WGPu borosilicate glass logs. The elimination disposition option spent non-uranium fuel product was found to present significantly greater barriers to proliferation than other plutonium disposal products

Destruction of plutonium using non-uranium fuels in pressurized water reactor peripheral assemblies

Energy Technology Data Exchange (ETDEWEB)

Chodak, III, Paul [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

1996-05-01

This thesis examines and confirms the feasibility of using non-uranium fuel in a pressurized water reactor (PWR) radial blanket to eliminate plutonium of both weapons and civilian origin. In the equilibrium cycle, the periphery of the PWR is loaded with alternating fresh and once burned non-uranium fuel assemblies, with the interior of the core comprised of conventional three batch UO₂ assemblies. Plutonium throughput is such that there is no net plutonium production: production in the interior is offset by destruction in the periphery. Using this approach a 50 MT WGPu inventory could be eliminated in approximately 400 reactor years of operation. Assuming all other existing constraints were removed, the 72 operating US PWRs could disposition 50 MT of WGPu in 5.6 years. Use of a low fissile loading plutonium-erbium inert-oxide-matrix composition in the peripheral assemblies essentially destroys 100% of the ²³⁹Pu and ≥90% {sub total}Pu over two 18 month fuel cycles. Core radial power peaking, reactivity vs EFPD profiles and core average reactivity coefficients were found to be comparable to standard PWR values. Hence, minimal impact on reload licensing is anticipated. Examination of potential candidate fuel matrices based on the existing experience base and thermo-physical properties resulted in the recommendation of three inert fuel matrix compositions for further study: zirconia, alumina and TRISO particle fuels. Objective metrics for quantifying the inherent proliferation resistance of plutonium host waste and fuel forms are proposed and were applied to compare the proposed spent WGPu non-uranium fuel to spent WGPu MOX fuels and WGPu borosilicate glass logs. The elimination disposition option spent non-uranium fuel product was found to present significantly greater barriers to proliferation than other plutonium disposal products.

Management routes for materials arising from the decommissioning of a PWR reactor

International Nuclear Information System (INIS)

Klein, M.; Demeulemeester, Y.; Moers, S.; Ponnet, M.

2001-01-01

The management of wastes from decommissioning is described for the on-going dismantling of the BR3 PWR small reactor. The incentive is put on the radionuclides characterization, the description of the various waste streams, the conditioning techniques for low radioactive waste (LAW) to high radioactive waste (RAW), the alternative evacuation routes (recycling in the nuclear, free release by decontamination) and the minimization of secondary wastes during dismantling. Finally, some considerations are given on the overall dismantling cost and on the relative costs of the various evacuation routes. (author)

FAMREC, PWR Lateral Mechanical Fuel Rod Assembly Response

International Nuclear Information System (INIS)

Guenzler, R.C.

1995-01-01

1 - Description of program or function: The Fuel Assembly Mechanical Response Code (FAMREC) calculates the lateral mechanical response of a row of fuel assemblies while allowing for two types of nonlinearities. The first type is a geometric nonlinearity in the form of gaps between individual assemblies and between peripheral assemblies and a boundary wall. Impacting is monitored across the gaps. The second nonlinearity is the permanent deformation of the fuel assembly spacer grid to compressive loading. 2 - Method of solution: The response is calculated in the modal plane. The coupled differential equations are solved in closed form using Laplace transformations. The discrete displacements and velocities are then calculated and the gaps in the system monitored at each axial elevation for impacting. These impact forces are then applied statistically at a given time-step, and equilibrium is found using a Gaussian elimination technique. Three impact force calculation methods are available: 1- a linear impact force and crushing load audit calculation, 2- a more detailed linear impact force and crushing load calculation, and 3- a non-linear grid calculation which allows for plastic deformation of the fuel assembly spacer grids. 3 - Restrictions on the complexity of the problem: Maxima of: 3601 time-steps and forces; 80 modes; 30 applied forces; 15 fuel assemblies; and 5 impact grids per assembly

Sodium fast reactor: an asset for a PWR UOX/MOX fleet - 5327

International Nuclear Information System (INIS)

Tiphine, M.; Coquelet-Pascal, C.; Girieud, R.; Eschbach, R.; Chabert, C.; Grosman, R.

2015-01-01

Due to its low fissile content, Pu from spent MOX fuels is sometimes regarded as not recyclable in LWR. Based on the existing French nuclear infrastructure (La Hague reprocessing plant and MELOX MOX manufacturing plant), AREVA and CEA have evaluated the conditions of Pu multi recycling in a 100% LWR fleet. As France is currently supporting a Fast Reactor prototype project, scenario studies have also been conducted to evaluate the contribution of a 600 MWe SFR in the LWR fleet. These scenario studies consider a nuclear fleet composed of 8 PWR 900 MWe, with or without the contribution of a SFR, and aim at evaluating the following points: -) the feasibility of Pu multi-recycling in PWR; -) the impact on the spent fuels storage; -) the reduction of the stored separated Pu; -) the impact on waste management and final disposal. The studies have been conducted with the COSI6 code, developed by CEA Nuclear Energy Direction since 1985, that simulates the evolution over time of a nuclear power plants fleet and of its associated fuel cycle facilities and provides material flux and isotopic compositions at each point of the scenario. To multi-recycle Pu into LWR MOX and to ensure flexibility, different reprocessing strategies were evaluated by adjusting the reprocessing order, the choice of used fuel assemblies according to their burn-up and the UOX/MOX proportions. The improvement of the Pu fissile quality and the kinetic of Pu multi-recycling in SFR depending on the initial Pu quality were also evaluated and led to a reintroduction of Pu in PWR MOX after a single irradiation in SFR, still in dilution with Pu from UOX to maintain a sufficient fissile quality. (authors)

Feasibility of using gadolinium as a burnable poison in PWR cores. Final report

International Nuclear Information System (INIS)

Rothleder, B.M.

1981-02-01

As an alternative to the use of lumped burnable absorbers in PWR cores, distributed burnable absorbers are being considered for generic application. These burnable absorbers take the form of Gd 2 O 3 mixed with UO 2 in selected fuel rods (as is currently done in BWR cores). The work discussed herein concerns a three-dimensional feasibility study of the use of such distributed burnable absorbers in PWR cores. This study of distributed burnable absorbers was performed for the first cycle of a typical current design PWR using the following steps: analysis of a generic reference core design; determination of gadolinium assembly designs; determination of a generic gadolinium core design; evaluation of feasibility by examining selected parameters; and redesign of the generic gadolinium core, using axial zoning

T Plant removal of PWR Chiller Subsystem

International Nuclear Information System (INIS)

Dana, C.M.

1994-01-01

The PWR Pool Chiller System is not longer required for support of the Shippingport Blanket Fuel Assemblies Storage. The Engineering Work Plan will provide the overall coordination of the documentation and physical changes to deactivate the unneeded subsystem. The physical removal of all energy sources for the Chiller equipment will be covered under a one time work plan. The documentation changes will be covered using approved Engineering Change Notices and Procedure Change Authorizations as needed

Expert system for assisting the repair operations on the control racks of the control rods assembly in a 900 MW PWR type reactor

International Nuclear Information System (INIS)

Monnier, B.; Doutre, J.L.; Franco, A.

1990-01-01

The expert system presented was developed for assisting the repair operations on the control equipment of the control rod assembly in a PWR type reactor. The expert system allows the representation of expert knowledge and diagnostic reasoning. The objective of the expert system is to achieve the most precise diagnostic and localizing of the breakdown elements, by processing the data acquired during breakdown. The development steps, the structure and the applications of the expert system are summarized. The expert system operates in an IBM PC equipped with a AMAIA 8 Mo card. A time schedule of 18 months is predicted [fr

NUPEC proves reliability of LWR fuel assemblies

International Nuclear Information System (INIS)

Anon.

1987-01-01

It is very important in assuring the safety of nuclear reactors to confirm the reliability of fuel assemblies. The test program of the Nuclear Power Engineering Center on the reliability of fuel assemblies has verified the high performance and reliability of Japanese LWR fuels, and confirmed the propriety of their design and fabrication. This claim is based on the data obtained from the fuel assemblies irradiated in commercial reactors. The NUPEC program includes irradiation test which has been conducted for 11 years since fiscal 1976, and the maximum thermal loading test using the out of pile test facilities simulating a real reactor which has been continued since fiscal 1978. The irradiation test on BWR fuel assemblies in No.3 reactor in Fukushima No.1 Nuclear Power Station, Tokyo Electric Power Co., Inc., and on PWR fuel assemblies in No.3 reactor in Mihama Power Station, Kansai Electric Power Co., Inc., and the maximum thermal loading test on BWR and PWR fuel assemblies are reported. The series of postirradiation examination of the fuel assemblies used for commercial reactors was conducted for the first time in Japan, and the highly systematic data on 27 items were obtained. (Kako, I.)

Application of digital control in Japanese PWR Plants

International Nuclear Information System (INIS)

Taguchi, S.; Kondo, Y.; Teranishi, S.; Matsumiya, M.; Takashima, M.; Nagai, T.

1986-01-01

More reliable and flexible control system to improve the plant availability and operability is constantly demanded. In order to answer the demands, digital control systems are being applied to Japanese PWR plants. Microprocessor-based digital control systems are widely used in other industries and show good performance. The digital control system has been already applied to the chemical and volume control system and the radioactive waste disposal system in the operating plants. These systems have been working as expected and demonstrating good performances. The digital control system for the reactor control system, which is the main control system of the PWR plants, is being developed. The design of the system has been already finished and the verification/validation process is now in progress

VVANTAGE 6 - an advanced fuel assembly design for VVER reactors

International Nuclear Information System (INIS)

Doshi, P.K.; DeMario, E.E.; Knott, R.P.

1993-01-01

Over the last 25 years, Westinghouse fuel assemblies for pressurized water reactors (PWR's) have undergone significant changes to the current VANTAGE 5. VANTAGE 5 PWR fuel includes features such as removable top nozzles, debris filter bottom nozzles, low-pressure-drop zircaloy grids, zircaloy intermediate flow mixing grids, optimized fuel rods, in-fuel burnable absorbers, and increased burnup capability to region average values of 48000 MWD/MTU. These features have now been adopted to the VVER reactors. Westinghouse has completed conceptual designs for an advanced fuel assembly and other core components for VVER-1000 reactors known as VANTAGE 6. This report describes the VVANTAGE 6 fuel assembly design

CECP, Decommissioning Costs for PWR and BWR

International Nuclear Information System (INIS)

Bierschbach, M.C.

1997-01-01

1 - Description of program or function: The Cost Estimating Computer Program CECP, designed for use on an IBM personal computer or equivalent, was developed for estimating the cost of decommissioning boiling water reactor (BWR) and light-water reactor (PWR) power stations to the point of license termination. 2 - Method of solution: Cost estimates include component, piping, and equipment removal costs; packaging costs; decontamination costs; transportation costs; burial volume and costs; and manpower staffing costs. Using equipment and consumables costs and inventory data supplied by the user, CECP calculates unit cost factors and then combines these factors with transportation and burial cost algorithms to produce a complete report of decommissioning costs. In addition to costs, CECP also calculates person-hours, crew-hours, and exposure person-hours associated with decommissioning. 3 - Restrictions on the complexity of the problem: The program is designed for a specific waste charge structure. The waste cost data structure cannot handle intermediate waste handlers or changes in the charge rate structures. The decommissioning of a reactor can be divided into 5 periods. 200 different items for special equipment costs are possible. The maximum amount for each special equipment item is 99,999,999$. You can support data for 10 buildings, 100 components each; ESTS1071/01: There are 65 components for 28 systems available to specify the contaminated systems costs (BWR). ESTS1071/02: There are 75 components for 25 systems available to specify the contaminated systems costs (PWR)

Generation of SCALE 6 Input Data File for Cross Section Library of PWR Spent Fuel

International Nuclear Information System (INIS)

Jeong, Chang Joon; Cho, Dong Keun

2010-11-01

In order to obtain the cross section libraries of the Korean Pressurized water reactor (PWR) spent fuel (SF), SCALE 6 code input files have been generated. The PWR fuel data were obtained from the nuclear design report (NDR) of the current operating PWRs. The input file were prepared for 16 fuel types such as 4 types of Westinghouse 14x14, 3 types of OPR-1000 16x16, 4 types of Westinghouse 16x16, and 6 types of Westinghouse 17x17. For each fuel type, 5 kinds of fuel enrichments have been considered such as 1.5, 2.0 ,3.0, 4.0 and 5.0 wt%. In the SCALE 6 calculation, a ENDF-V 44 group was used. The 25 burnup step until 72000 MWD/T was used. A 1/4 symmetry model was used for 16x16 and 17x17 fuel assembly, and 1/2 symmetry model was used for 14x14 fuel assembly The generated cross section libraries will be used for the source-term analysis of the PWR SF

Benchmarking Computational Fluid Dynamics for Application to PWR Fuel

International Nuclear Information System (INIS)

Smith, L.D. III; Conner, M.E.; Liu, B.; Dzodzo, B.; Paramonov, D.V.; Beasley, D.E.; Langford, H.M.; Holloway, M.V.

2002-01-01

The present study demonstrates a process used to develop confidence in Computational Fluid Dynamics (CFD) as a tool to investigate flow and temperature distributions in a PWR fuel bundle. The velocity and temperature fields produced by a mixing spacer grid of a PWR fuel assembly are quite complex. Before using CFD to evaluate these flow fields, a rigorous benchmarking effort should be performed to ensure that reasonable results are obtained. Westinghouse has developed a method to quantitatively benchmark CFD tools against data at conditions representative of the PWR. Several measurements in a 5 x 5 rod bundle were performed. Lateral flow-field testing employed visualization techniques and Particle Image Velocimetry (PIV). Heat transfer testing involved measurements of the single-phase heat transfer coefficient downstream of the spacer grid. These test results were used to compare with CFD predictions. Among the parameters optimized in the CFD models based on this comparison with data include computational mesh, turbulence model, and boundary conditions. As an outcome of this effort, a methodology was developed for CFD modeling that provides confidence in the numerical results. (authors)

Modeling for speciation of radionuclides in waste packages with high-level radioactive wastes

International Nuclear Information System (INIS)

Weyand, Torben; Bracke, Guido; Seher, Holger

2016-10-01

Based on a literature search on radioactive waste inventories adequate thermodynamic data for model inventories were derived for geochemical model calculations using PHREEQC in order to determine the solid phase composition of high-level radioactive wastes in different containers. The calculations were performed for different model inventories (PWR-MOX, PWR-UO2, BWR-MOX, BMR-UO2) assuming intact containers under reduction conditions. The effect of a defect in the container on the solid phase composition was considered in variation calculations assuming air contact induced oxidation.

Pressurized Water Reactors (PWR) and Boiling Water Reactors (BWR) are compared

International Nuclear Information System (INIS)

Greneche, D.

2014-01-01

This article compares the 2 types of light water reactors that are used to produce electricity: the Pressurized Water Reactor (PWR) and the Boiling Water Reactor (BWR). Historically the BWR concept was developed after the PWR concept. Today 80% of light water reactors operating in the world are of PWR-type. This comparison is comprehensive and detailed. First the main technical features are reviewed and compared: reactor architecture, core and fuel design, reactivity control, reactor vessel, cooling systems and reactor containment. Secondly, various aspects concerning reactor operations like reactor control, fuel management, maintenance, inspections, radiation protection, waste generation and reactor reliability are presented and compared for both reactors. As for the issue of safety, it is highlighted that the accidental situations are too different for the 2 reactors to be compared. The main features of reactor safety are explained for both reactors

Coolant degassing device for PWR type reactors

International Nuclear Information System (INIS)

Kita, Kaoru; Takezawa, Kazuaki; Minemoto, Masaki.

1982-01-01

Purpose: To efficiently decrease the rare gas concentration in primary coolants, as well as shorten the degassing time required for the periodical inspection in the waste gas processing system of a PWR type reactor. Constitution: Usual degassing method by supplying hydrogen or nitrogen to a volume control tank is replaced with a method of utilizing a degassing tower (method of flowing down processing liquid into the filled tower from above while uprising streams from the bottom of the tower thereby degassing the gases dissolved in the liquid into the steams). The degassing tower is combined with a hydrogen separator or hydrogen recombiner to constitute a waste gas processing system. (Ikeda, J.)

The application of modern nodal methods to PWR reactor physics analysis

International Nuclear Information System (INIS)

Knight, M.P.

1988-06-01

The objective of this research is to develop efficient computational procedures for PWR reactor calculations, based on modern nodal methods. The analytic nodal method, which is characterised by the use of exact exponential expansions in transverse-integrated equations, is implemented within an existing finite-difference code. This shows considerable accuracy and efficiency on standard benchmark problems, very much in line with existing experience with nodal methods., Assembly powers can be calculated to within 2.0% with just one mesh per assembly. (author)

Radioactive waste management of experimental DUPIC fuel fabrication process

International Nuclear Information System (INIS)

Lee, H. H.; Park, J. J.; Shin, J. M.; Yang, M. S.; Hong, K. P.

2001-01-01

The concept of DUPIC(Direct Use of Spent PWR Fuel in CANDU Reactors) is a dry processing technology to manufacture CANDU compatible DUPIC fuel from spent PWR fuel material. Real spent PWR fuel was used in IMEF M6 hot cell to carry out DUPIC experiment. Afterwards, about 200 kg-U of spent PWR fuel is supposed to be used till 2006. This study has been conducted in some hot cells of PIEF and M6 cell of IMEF. There are various forms of nuclear material such as rod cut, powder, green pellet, sintered pellet, fabrication debris, fuel rod, fuel bundle, sample, and process waste produced from various manufacturing experiment of DUPIC fuel. After completing test, the above nuclear wastes and test equipment etc. will be classified as radioactive waste, transferred to storage facility and managed rigorously according to domestic and international laws until the final management policy is determined. It is desirable to review management options in advance for radioactive waste generated from manufacturing experiment of DUPIC nuclear fuel as well as residual nuclear material and dismantled equipment. This paper includes basic plan for DUPIC radwaste, arising source and estimated amount of radioactive waste, waste classification and packing, transport cask, transport procedures

Evolutionary developments of advanced PWR nuclear fuels and cladding materials

International Nuclear Information System (INIS)

Kim, Kyu-Tae

2013-01-01

Highlights: • PWR fuel and cladding materials development processes are provided. • Evolution of PWR advanced fuel in U.S.A. and in Korea is described. • Cutting-edge design features against grid-to-rod fretting and debris are explained. • High performance data of advanced grids, debris filters and claddings are given. -- Abstract: The evolutionary developments of advanced PWR fuels and cladding materials are explained with outstanding design features of nuclear fuel assembly components and zirconium-base cladding materials. The advanced PWR fuel and cladding materials development processes are also provided along with verification tests, which can be used as guidelines for newcomers planning to develop an advanced fuel for the first time. The up-to-date advanced fuels with the advanced cladding materials may provide a high level of economic utilization and reliable performance even under current and upcoming aggressive operating conditions. To be specific, nuclear fuel vendors may achieve high fuel burnup capability of between 45,000 and 65,000 MWD/MTU batch average, overpower thermal margin of as much as 15% and longer cycle length up to 24 months on the one hand and fuel failure rates of around 10 −6 on the other hand. However, there is still a need for better understanding of grid-to-rod fretting wear mechanisms leading to major PWR fuel defects in the world and subsequently a driving force for developing innovative spacer grid designs with zero fretting wear-induced fuel failure

Experimental studies of resistance fretting-wear of fuel rods for VVER-1000 and TVS-KVADRAT fuel assemblies

International Nuclear Information System (INIS)

Makarov, V.; Afanasiev, A.; Egorov, Yu.; Matvienko, I.

2015-01-01

The paper covers the results of the studies performed to justify the wear resistance of fuel rods in contact with the spacer grids of TVS VVER-1000 fuel assembly and TVS-KVADRAT square fuel assembly of Russian design for PWR-900 reactor. The presented results of three testing stages comprise: Testing of mockup fuel rods of VVER TVS fuel assembly for fretting wear under the conditions of the water chemistry of VVER reactor; Testing models of different design embodiments of the fuel rods for VVER TVS fuel assembly for fretting wear in still cold water; Testing mockup fuel rods of TVS-KVADRAT square fuel assembly for PWR reactor for frettingwear under the conditions of PWR water chemistry. The effect of structural and operational factors was determined (amplitudes, fuel rod vibration frequencies, values of cladding-to-spacer grid cell gap for the depth of fuel rod cladding wear etc.), an assessment was made of the threshold values of fuel rod vibration parameters, which, if not exceeded, provide the absence of the fuel rod cladding fretting wear in the fuel rod-to spacer grid contact area. Key words: fretting wear, fuel rod, spacer grid, VVER, PWR (author)

Performance Specification Shippinpark Pressurized Water Reactor Fuel Drying and Canister Inerting System for PWR Core 2 Blanket Fuel Assemblies Stored within Shippingport Spent Fuel Canisters

International Nuclear Information System (INIS)

JOHNSON, D.M.

2000-01-01

This specification establishes the performance requirements and basic design requirements imposed on the fuel drying and canister inerting system for Shippingport Pressurized Water Reactor (PWR) Core 2 blanket fuel assemblies (BFAs) stored within Shippingport spent fuel (SSFCs) canisters (fuel drying and canister inerting system). This fuel drying and canister inerting system is a component of the U.S. Department of Energy, Richland Operations Office (RL) Spent Nuclear Fuels Project at the Hanford Site. The fuel drying and canister inerting system provides for removing water and establishing an inert environment for Shippingport PWR Core 2 BFAs stored within SSFCs. A policy established by the U.S. Department of Energy (DOE) states that new SNF facilities (this is interpreted to include structures, systems and components) shall achieve nuclear safety equivalence to comparable U.S. Nuclear Regulatory Commission (NRC)-licensed facilities. This will be accomplished in part by applying appropriate NRC requirements for comparable NRC-licensed facilities to the fuel drying and canister inerting system, in addition to applicable DOE regulations and orders

Surrogate fuel assembly multi-axis shaker tests to simulate normal conditions of rail and truck transport

Energy Technology Data Exchange (ETDEWEB)

McConnell, Paul E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Koenig, Greg John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Uncapher, William Leonard [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Grey, Carissa [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Engelhardt, Charles [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Saltzstein, Sylvia J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sorenson, Ken B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-05-01

This report describes the third set of tests (the “DCLa shaker tests”) of an instrumented surrogate PWR fuel assembly. The purpose of this set of tests was to measure strains and accelerations on Zircaloy-4 fuel rods when the PWR assembly was subjected to rail and truck loadings simulating normal conditions of transport when affixed to a multi-axis shaker. This is the first set of tests of the assembly simulating rail normal conditions of transport.

Industrial assessment of nonbackfittable PWR design modifications. Final report

International Nuclear Information System (INIS)

Matzie, R.A.; Daleas, R.S.; Miller, D.D.

1980-11-01

As part of the US Department of Energy's Advanced Reactor Design Study, various nonbackfittable PWR design modifications were evaluated to determine their potential for improved uranium utilization and commercial viability. Combustion Engineering, Inc. contributed to this effort through participation in the Battelle Pacific Northwest Laboratory industrial assessment of such design modifications. Seven modifications, including the use of higher primary system temperatures and pressures, rapid-frequent refueling, end-of-cycle stretchout, core periphery modifications, radial blankets, low power density cores, and small PWR assemblies, were evaluated with respect to uranium utilization, economics, technical and operational complexity, and several other subjective considerations. Rapid-frequent refueling was judged to have the highest potential although it would probably not be economical for the majority of reactors with the design assumptions used in this assessment

Actinides transmutation - a comparison of results for PWR benchmark

International Nuclear Information System (INIS)

Claro, Luiz H.

2009-01-01

The physical aspects involved in the Partitioning and Transmutation (P and T) of minor actinides (MA) and fission products (FP) generated by reactors PWR are of great interest in the nuclear industry. Besides these the reduction in the storage of radioactive wastes are related with the acceptability of the nuclear electric power. From the several concepts for partitioning and transmutation suggested in literature, one of them involves PWR reactors to burn the fuel containing plutonium and minor actinides reprocessed of UO 2 used in previous stages. In this work are presented the results of the calculations of a benchmark in P and T carried with WIMSD5B program using its new cross sections library generated from the ENDF-B-VII and the comparison with the results published in literature by other calculations. For comparison, was used the benchmark transmutation concept based in a typical PWR cell and the analyzed results were the k∞ and the atomic density of the isotopes Np-239, Pu-241, Pu-242 and Am-242m, as function of burnup considering discharge of 50 GWd/tHM. (author)

A study on the direct use of spent PWR fuel in CANDU -A study on the radioactive waste management for DUPIC fuel cycle-

International Nuclear Information System (INIS)

Park, Hyun Soo; Jun, Kwan Sik; Nah, Jung Won; Park, Jang Jin; Kim, Jong Hoh; Cho, Yung Hyun; Baek, Seung Woo; Shin, Jin Myung; Yang, Seung Yung

1994-07-01

The immobilization materials for radioactive wastes resulting from the DUPIC fuel manufacturing process were selected and their characteristics were evaluated. To predict the trapping behavior of the Ruthenium, a semi-volatile nuclide, its volatility was measured and thermogravimetric analysis were performed with simulated fuel. New Ruthenium trapping material was developed which is deposited on ceramic honey-comb monolith of cordierite. The base glass was manufactured with fly ash added to the borosilicate glass. The composition of the scrap waste was calculated based on the PWR spent fuel which has initial 235 U content of 3.5%, burnup of 35,000 MWD/MTU and cooling time of 10 years. Simulated waste glass was manufactured, and its chemical durability was evaluated by soxhlet leach test. Radioactivity of non-oxidized cladding material were measured. The preliminary design criteria were prepared for off-gas treatment system in IMEF. 31 figs, 42 tabs, 51 refs. (Author)

Tritium contaminated waste management at the tritium systems test assembly

International Nuclear Information System (INIS)

Jalbert, R.A.; Carlson, R.V.

1987-01-01

The Tritium Systems Test Assembly (TSTA) at Los Alamos continues to move toward full operation of an integrated, full-sized, computer-controlled fusion fuel processing loop. Concurrent nonloop experiments further the development of advanced tritium technologies and handling methods. Since tritium operations began in June 1984, tritium contaminated wastes have been produced at TSTA that are roughly typical in kind and amount of those to be produced by tritium fueling operations at fusion reactors. Methods of managing these wastes are described, including information on some methods of decontamination so that equipment can be reused. Data are given on the kinds and amounts of wastes and the general level of contamination. Also included are data on environmental emissions and doses to personnel that have resulted from TSTA operations. Particular problems in waste managements are discussed

Development of Cost Estimation Methodology of Decommissioning for PWR

International Nuclear Information System (INIS)

Lee, Sang Il; Yoo, Yeon Jae; Lim, Yong Kyu; Chang, Hyeon Sik; Song, Geun Ho

2013-01-01

The permanent closure of nuclear power plant should be conducted with the strict laws and the profound planning including the cost and schedule estimation because the plant is very contaminated with the radioactivity. In Korea, there are two types of the nuclear power plant. One is the pressurized light water reactor (PWR) and the other is the pressurized heavy water reactor (PHWR) called as CANDU reactor. Also, the 50% of the operating nuclear power plant in Korea is the PWRs which were originally designed by CE (Combustion Engineering). There have been experiences about the decommissioning of Westinghouse type PWR, but are few experiences on that of CE type PWR. Therefore, the purpose of this paper is to develop the cost estimation methodology and evaluate technical level of decommissioning for the application to CE type PWR based on the system engineering technology. The aim of present study is to develop the cost estimation methodology of decommissioning for application to PWR. Through the study, the following conclusions are obtained: · Based on the system engineering, the decommissioning work can be classified as Set, Subset, Task, Subtask and Work cost units. · The Set and Task structure are grouped as 29 Sets and 15 Task s, respectively. · The final result shows the cost and project schedule for the project control and risk management. · The present results are preliminary and should be refined and improved based on the modeling and cost data reflecting available technology and current costs like labor and waste data

Surrogate fuel assembly multi-axis shaker tests to simulate normal conditions of rail and truck transport

Energy Technology Data Exchange (ETDEWEB)

McConnell, Paul E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Koenig, Greg John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Uncapher, William Leonard [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Grey, Carissa [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Engelhardt, Charles [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Saltzstein, Sylvia J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sorenson, Ken B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-05-12

This report describes the third set of tests (the “DCL^a shaker tests”) of an instrumented surrogate PWR fuel assembly. The purpose of this set of tests was to measure strains and accelerations on Zircaloy-4 fuel rods when the PWR assembly was subjected to rail and truck loadings simulating normal conditions of transport when affixed to a multi-axis shaker. This is the first set of tests of the assembly simulating rail normal conditions of transport.

ROX PWR

International Nuclear Information System (INIS)

Akie, H.; Yamashita, T.; Shirasu, N.; Takano, H.; Anoda, Y.; Kimura, H.

1999-01-01

For an efficient burnup of excess plutonium from nuclear reactors spent fuels and dismantled warheads, plutonium rock-like oxide(ROX) fuel has been investigated. The ROX fuel is expected to provide high Pu transmutation capability, irradiation stability and chemical and geological stability. While, a zirconia-based ROX(Zr-ROX)-fueled PWR core has some problems of Doppler reactivity coefficient and power peaking factor. For the improvement of these characteristics, two approaches were considered: the additives such as UO 2 , ThO 2 and Er 2 O 3 , and a heterogeneous core with Zr-ROX and UO 2 assemblies. As a result, the additives UO 2 + Er 2 O 3 are found to sufficiently improve the reactivity coefficients and accident behavior, and to flatten power distribution. On the other hand, in the 1/3Zr-ROX + 2/3UO 2 heterogeneous core, further reduction of power peaking seems necessary. (author)

Nuclear criticality safety analysis for the traveller PWR fuel shipping package

Energy Technology Data Exchange (ETDEWEB)

Vescovi, P.J.; Kent, N.A.; Casado, C.A. [Westinghouse Electric Co., LLC, Columbia, SC (United States)]|[ENUSA Industrias Avanzadas SA, Madrid (Spain)

2004-07-01

The Traveller PWR fresh fuel shipping package represents a radical departure from conventional PWR fuel package designs. Two immediately noticeable features of the Traveller are that it carries a single fuel assembly instead of two as do other package designs, and that it has built-in moderator, which forms part of the flux-trap system. The criticality safety case shows that the Traveller satisfies both U.S. and IAEA licensing requirements, and demonstrates that the package remains acceptably subcritical under normal conditions and hypothetical accident conditions of transport. This paper looks at the modeling techniques that were used to analyze the several accident scenarios that were considered, including: Lattice pitch expansion; Lattice pitch expansion along the fuel assembly length; Preferential flooding (selective flooding of different cavities); Differential flooding (varying water levels inside different cavities); Partial flooding (varying water density); Axial rod displacement; o Sensitivity studies of variable foam densities and boron content in packaging; Analysis for carrying loose rods in a rodbox; The criticality safety case for the Traveller proved to be a successful cooperative effort between ENUSA and Westinghouse.

Nuclear criticality safety analysis for the traveller PWR fuel shipping package

International Nuclear Information System (INIS)

Vescovi, P.J.; Kent, N.A.; Casado, C.A.

2004-01-01

The Traveller PWR fresh fuel shipping package represents a radical departure from conventional PWR fuel package designs. Two immediately noticeable features of the Traveller are that it carries a single fuel assembly instead of two as do other package designs, and that it has built-in moderator, which forms part of the flux-trap system. The criticality safety case shows that the Traveller satisfies both U.S. and IAEA licensing requirements, and demonstrates that the package remains acceptably subcritical under normal conditions and hypothetical accident conditions of transport. This paper looks at the modeling techniques that were used to analyze the several accident scenarios that were considered, including: Lattice pitch expansion; Lattice pitch expansion along the fuel assembly length; Preferential flooding (selective flooding of different cavities); Differential flooding (varying water levels inside different cavities); Partial flooding (varying water density); Axial rod displacement; o Sensitivity studies of variable foam densities and boron content in packaging; Analysis for carrying loose rods in a rodbox; The criticality safety case for the Traveller proved to be a successful cooperative effort between ENUSA and Westinghouse

Acceptance of failed SNF [spent nuclear fuel] assemblies by the Federal Waste Management System

International Nuclear Information System (INIS)

1990-03-01

This report is one of a series of eight prepared by E. R. Johnson Associates, Inc. (JAI) under ORNL's contract with DOE's OCRWM Systems Integration Program and in support of the Annual Capacity Report (ACR) Issue Resolution Process. The report topics relate specifically to the list of high priority technical waste acceptance issues developed jointly by DOE and a utility-working group. JAI performed various analyses and studies on each topic to serve as starting points for further discussion and analysis leading eventually to finalizing the process by which DOE will accept spent fuel and waste into its waste management system. The eight reports are concerned with the conditions under which spent fuel and high level waste will be accepted in the following categories: failed fuel; consolidated fuel and associated structural parts; non-fuel-assembly hardware; fuel in metal storage casks; fuel in multi-element sealed canisters; inspection and testing requirements for wastes; canister criteria; spent fuel selection for delivery; and defense and commercial high-level waste packages. This document discusses acceptance of failed spent fuel assemblies by the Federal Waste Management System. 18 refs., 7 figs., 25 tabs

3-D full core calculations for the long-term behaviour of PWR's

International Nuclear Information System (INIS)

Winter, H.J.; Koebke, K.; Wagner, M.R.

1987-01-01

Presently, the most realistic simulation of a PWR core is by means of three-dimensional (3-D) full core calculations. Only by such 3-D representations can the large scope of axial effects be treated in an accurate and direct way, without the need to perform various auxiliary calculations. Although the computationally efficient burnup-corrected nodal expansion method (NEM-BC) is used, the computing effort for 3-D reactor calculations becomes rather high, e.g. a storage of about 320000 words is required to describe a 1300 MWe PWR. NEM-BC was introduced (1979) into KWU's package of PWR design codes because of its high accuracy and the great reduction of computing time and storage requirements in comparison to other methods. The application of NEM-BC to 3-dimensional PWR design is strongly correlated with the progress achieved in the solution of the homogenization and dehomogenization problem. By means of suitable methods (equivalence theory) the transport-theoretical information of the pinwise power and burnup distribution for the heterogeneous fuel assemblies is transferred in a consistent manner to the full core reactor solution. The new methods and the corresponding code system are explained in some detail. (orig.)

Parameters calculation of fuel assembly with complex geometry

International Nuclear Information System (INIS)

Wu Hongchun; Ju Haitao; Yao Dong

2006-01-01

The code DRAGON was developed for CANDU reactor by Ecole Polytechnique de Montreal of Canada. In order to validate the DRAGON code's applicability for complex geometry fuel assembly calculation, the rod shape fuel assembly of PWR benchmark problem and the plate shape fuel assembly of MTR benchmark problem were analyzed by DRAGON code. Some other shape fuel assemblies were also discussed simply. Calculation results show that the DRAGON code can be used to calculate variform fuel assembly and the precision is high. (authors)

Lean manufacturing implementation in reducing waste for electronic assembly line

Directory of Open Access Journals (Sweden)

Zakaria Nurul Husna

2017-01-01

Full Text Available Lean manufacturing is the most convenient way to eliminate unnecessary waste and can provide what customers demand. This paper presents possibilities and sustainability of application of lean manufacturing method by using a virtual simulation of the workers performance in a line production of small and medium industry. Actual case study and Witness simulation were used in this study to find the waste that exists in the production and identified the performance of workers in the production line. Lean manufacturing concept has identified and rectified problems related to low productivity in the assembly line. The case study is involved a line production for electronic part assembly. The result of this preliminary study should illustrate the relationship of worker’s performance by lean manufacturing method as well as the productivity improvements which help to reduce cost for manufacturer. Lean manufacturing method has been used during the study to reduce the cost when waste is eliminated by reducing the workstation without reducing the performance of the production. The performance of the production is increased when allocating the labor in a needed working area. Lastly, the study also proves that the new layout has improved the process to be used for future production process.

A method to determine the dampening system of control rod drop mechanism for PWR reactors

International Nuclear Information System (INIS)

Trindade, C.E.; Mattos, J.R.L. de; Perrotta, J.A.

1988-08-01

A method to determine the Control Assembly damping drop system (dashpot/guide tube) was developed. It's presented a theoretical model, an experimental device and the procedures to determine this system, which is used in PWR reactors. (author) [pt

PWR auxiliary systems, safety and emergency systems, accident analysis, operation

International Nuclear Information System (INIS)

Meyer, P.J.

1976-01-01

The author presents a description of PWR auxiliary systems like volume control, boric acid control, coolant purification, -degassing, -storage and -treatment system and waste processing systems. Residual heat removal systems, emergency systems and containment designs are discussed. As an accident analysis the author gives a survey over malfunctions and disturbances in the field of reactor operations. (TK) [de

Solution of a benchmark set problems for BWR and PWR reactors with UO2 and MOX fuels using CASMO-4

International Nuclear Information System (INIS)

Martinez F, M.A.; Valle G, E. del; Alonso V, G.

2007-01-01

In this work some of the results for a group of benchmark problems of light water reactors that allow to study the physics of the fuels of these reactors are presented. These benchmark problems were proposed by Akio Yamamoto and collaborators in 2002 and they include two fuel types; uranium dioxide (UO 2 ) and mixed oxides (MOX). The range of problems that its cover embraces three different configurations: unitary cell for a fuel bar, fuel assemble of PWR and fuel assemble of BWR what allows to carry out an understanding analysis of the problems related with the fuel performance of new generation in light water reactors with high burnt. Also these benchmark problems help to understand the fuel administration in core of a BWR like of a PWR. The calculations were carried out with CMS (of their initials in English Core Management Software), particularly with CASMO-4 that is a code designed to carry out analysis of fuels burnt of fuel bars cells as well as fuel assemblies as much for PWR as for BWR and that it is part in turn of the CMS code. (Author)

Contribution to the experimental qualification of PWR fuel storage calculations

International Nuclear Information System (INIS)

Marsault, Philippe.

1980-12-01

Experiments were carried out on assemblies representative of those used in PWR reactors in a configuration made critical with a driver zone. In this way, certain parameters were able to be measured using current classical techniques. As the multiplication factor for a group of assemblies cannot be determined directly, substitutions were made with an equivalent homogeneous lattice in which Laplacian measurements could be made. The k(infinite) factor was obtained by introducing a migration area which can only be obtained from calculations. Experimental storage studies realized during the CRISTO 1 campaign utilize: 1) a lattice with 4 14x14 pin assemblies immersed in ordinary water; 2) a lattice with 4 14x14 pin assemblies and 3) a regular lattice. The CRISTO experiment enabled criticality calculations to be qualified with these lattices for storage under accidental conditions [fr

Evaluation of PWR and BWR assembly benchmark calculations. Status report of EPRI computational benchmark results, performed in the framework of the Netherlands` PINK programme (Joint project of ECN, IRI, KEMA and GKN)

Energy Technology Data Exchange (ETDEWEB)

Gruppelaar, H. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Klippel, H.T. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Kloosterman, J.L. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Hoogenboom, J.E. [Technische Univ. Delft (Netherlands). Interfacultair Reactor Instituut; Leege, P.F.A. de [Technische Univ. Delft (Netherlands). Interfacultair Reactor Instituut; Verhagen, F.C.M. [Keuring van Electrotechnische Materialen NV, Arnhem (Netherlands); Bruggink, J.C. [Gemeenschappelijke Kernenergiecentrale Nederland N.V., Dodewaard (Netherlands)

1993-11-01

Benchmark results of the Dutch PINK working group on calculational benchmarks on single pin cell and multipin assemblies as defined by EPRI are presented and evaluated. First a short update of methods used by the various institutes involved is given as well as an update of the status with respect to previous performed pin-cell calculations. Problems detected in previous pin-cell calculations are inspected more closely. Detailed discussion of results of multipin assembly calculations is given. The assembly consists of 9 pins in a multicell square lattice in which the central pin is filled differently, i.e. a Gd pin for the BWR assembly and a control rod/guide tube for the PWR assembly. The results for pin cells showed a rather good overall agreement between the four participants although BWR pins with high void fraction turned out to be difficult to calculate. With respect to burnup calculations good overall agreement for the reactivity swing was obtained, provided that a fine time grid is used. (orig.)

Evaluation of PWR and BWR assembly benchmark calculations. Status report of EPRI computational benchmark results, performed in the framework of the Netherlands' PINK programme (Joint project of ECN, IRI, KEMA and GKN)

International Nuclear Information System (INIS)

Gruppelaar, H.; Klippel, H.T.; Kloosterman, J.L.; Hoogenboom, J.E.; Bruggink, J.C.

1993-11-01

Benchmark results of the Dutch PINK working group on calculational benchmarks on single pin cell and multipin assemblies as defined by EPRI are presented and evaluated. First a short update of methods used by the various institutes involved is given as well as an update of the status with respect to previous performed pin-cell calculations. Problems detected in previous pin-cell calculations are inspected more closely. Detailed discussion of results of multipin assembly calculations is given. The assembly consists of 9 pins in a multicell square lattice in which the central pin is filled differently, i.e. a Gd pin for the BWR assembly and a control rod/guide tube for the PWR assembly. The results for pin cells showed a rather good overall agreement between the four participants although BWR pins with high void fraction turned out to be difficult to calculate. With respect to burnup calculations good overall agreement for the reactivity swing was obtained, provided that a fine time grid is used. (orig.)

Resource Prospects of Municipal Solid Wastes Generatedin the Ga East Municipal Assembly of Ghana

OpenAIRE

Benedicta Abiti; Susanne Hartard; Heike B. Bradl; Davar Pishva; John Kojo Ahiakpa

2017-01-01

Background. Municipal solid wastes management has recently become an important public health concern. Municipal solid wastes are a major source of raw materials that could be used for resource recovery for diverse applications. Objectives. The present study aimed to determine the composition of municipal solid waste and recoverable resources from the waste of the Ga East Municipal Assembly (GEMA) in the Greater Accra region of Ghana. Methods. An exploratory approach was used to collect ...

A study on the direct use of spent PWR fuel in CANDU -A study on the radioactive waste management for DUPIC fuel cycle-

Energy Technology Data Exchange (ETDEWEB)

Park, Hyun Soo; Jun, Kwan Sik; Nah, Jung Won; Park, Jang Jin; Kim, Jong Hoh; Cho, Yung Hyun; Baek, Seung Woo; Shin, Jin Myung; Yang, Seung Yung [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1994-07-01

The immobilization materials for radioactive wastes resulting from the DUPIC fuel manufacturing process were selected and their characteristics were evaluated. To predict the trapping behavior of the Ruthenium, a semi-volatile nuclide, its volatility was measured and thermogravimetric analysis were performed with simulated fuel. New Ruthenium trapping material was developed which is deposited on ceramic honey-comb monolith of cordierite. The base glass was manufactured with fly ash added to the borosilicate glass. The composition of the scrap waste was calculated based on the PWR spent fuel which has initial {sup 235}U content of 3.5%, burnup of 35,000 MWD/MTU and cooling time of 10 years. Simulated waste glass was manufactured, and its chemical durability was evaluated by soxhlet leach test. Radioactivity of non-oxidized cladding material were measured. The preliminary design criteria were prepared for off-gas treatment system in IMEF. 31 figs, 42 tabs, 51 refs. (Author).

Study on characteristics of spent PWR cladding hull for categorizing into Non-TRU waste

International Nuclear Information System (INIS)

Jung, In Ha; Kim, Jong Ho; Park, Jang Jin; Shin, Jin Myeong; Lee, Ho Hee; Yang, Myung Seung

2005-01-01

AFCI and GEN-IV programs aim for decreasing the high level radioactive wastes to be disposed. They also try to get valuable materials to recycle as resources such as uranium and plutonium. On the other hand, cladding hull expected to be one-thirds in volume of spent fuel assembly has not studied so much in the point view of recycling to reuse. Since traditional process of reprocessing was wet process, cladding hull generating through the reprocessing process was unavoidably contaminated with TRU by acid solvent during the process. Therefore, cladding hull has been classified into TRU wastes or high level wastes. According to the strategy for TRU high level radioactive wastes of USA as well as Korea, it regulates in two respects. One is activity and the other is heat generation. In respect of activity, TRU waste contains more than 100 nCi/kg of alpha emits with longer half life than 20 years and higher than 92 in atomic number. Also, wastes are categorized into TRU waste when it generates higher than 2kW/m3, in the respect of heat generation. Our results as well as literatures, almost all of TRU nuclides in the cladding hull are responsible for remained uranium and plutonium owing to pellet-cladding interaction. In addition, recoiled fission products on the surface of the cladding hull serve as heat generator. Up to now, decontamination of the cladding hull generating from the reprocessing of wet process is regarded as valueless and un-economic works owing to the amount of second waste produced

ROX PWR

Energy Technology Data Exchange (ETDEWEB)

Akie, H.; Yamashita, T.; Shirasu, N.; Takano, H.; Anoda, Y.; Kimura, H. [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1999-12-01

For an efficient burnup of excess plutonium from nuclear reactors spent fuels and dismantled warheads, plutonium rock-like oxide(ROX) fuel has been investigated. The ROX fuel is expected to provide high Pu transmutation capability, irradiation stability and chemical and geological stability. While, a zirconia-based ROX(Zr-ROX)-fueled PWR core has some problems of Doppler reactivity coefficient and power peaking factor. For the improvement of these characteristics, two approaches were considered: the additives such as UO{sub 2}, ThO{sub 2} and Er{sub 2}O{sub 3}, and a heterogeneous core with Zr-ROX and UO{sub 2} assemblies. As a result, the additives UO{sub 2}+ Er{sub 2}O{sub 3} are found to sufficiently improve the reactivity coefficients and accident behavior, and to flatten power distribution. On the other hand, in the 1/3Zr-ROX + 2/3UO{sub 2} heterogeneous core, further reduction of power peaking seems necessary. (author)

Nondestructive examination of Oconee 1 fuel assemblies after three cycles of irradiation

International Nuclear Information System (INIS)

Pyecha, T.D.; Davis, H.H.; Mayer, J.T.; Guthrie, B.A. III; Larson, J.G.

1979-09-01

The Babcock and Wilcox Company (B and W) in conjunction with Duke Power Company is participating in a Department of Energy sponsored research and development program to qualify current design pressurized water reactor (PWR) fuel assemblies for extended burnup (>40,000 MWd/mtU). The information obtained from this program will provide a basis for future design improvements in PWR fuel assemblies culminating in an extended burnup assembly having a nominal operating limit of approximately 50,000 MWd/mtU. An extension of the current assembly design to higher burnups will result in the following benefits: (1) lower uranium ore requirements, (2) greater fuel cycle efficiency, (3) reduction in spent fuel storage requirements, and (4) increased flexibility in tailoring fuel batch sizes to better accommodate the varying energy requirements of the utilities

ROSA-IV Large Scale Test Facility (LSTF) system description for second simulated fuel assembly

International Nuclear Information System (INIS)

1990-10-01

The ROSA-IV Program's Large Scale Test Facility (LSTF) is a test facility for integral simulation of thermal-hydraulic response of a pressurized water reactor (PWR) during small break loss-of-coolant accidents (LOCAs) and transients. In this facility, the PWR core nuclear fuel rods are simulated using electric heater rods. The simulated fuel assembly which was installed during the facility construction was replaced with a new one in 1988. The first test with this second simulated fuel assembly was conducted in December 1988. This report describes the facility configuration and characteristics as of this date (December 1988) including the new simulated fuel assembly design and the facility changes which were made during the testing with the first assembly as well as during the renewal of the simulated fuel assembly. (author)

Analysis of reactivity worths of highly-burnt PWR fuel samples measured in LWR-PROTEUS Phase II

Energy Technology Data Exchange (ETDEWEB)

Grimm, Peter; Murphy, Michael F.; Jatuff, Fabian; Seiler, Rudolf [Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland)

2008-07-01

The reactivity loss of PWR fuel with burnup has been determined experimentally by inserting fresh and highly-burnt fuel samples in a PWR test lattice in the framework of the LWR-PROTEUS Phase II programme. Seven UO{sub 2} samples irradiated in a Swiss PWR plant with burnups ranging from approx40 to approx120 MWd/kg and four MOX samples with burnups up to approx70 MWd/kg were oscillated in a test region constituted of actual PWR UO{sub 2} fuel rods in the centre of the PROTEUS zero-power experimental facility. The measurements were analyzed using the CASMO-4E fuel assembly code and a cross section library based on the ENDF/B-VI evaluation. The results show close proximity between calculated and measured reactivity effects and no trend for a deterioration of the quality of the prediction at high burnup. The analysis thus demonstrates the high accuracy of the calculation of the reactivity of highly-burnt fuel. (authors)

The comparison of available data on PWR assembly thermal behavior with analytical predictions. Topical report (final)

International Nuclear Information System (INIS)

Liu, J.; Todreas, N.

1979-02-01

The comparison of available data with analytical predictions has been illustrated in this report. Since few data on the cross flow are available, a study of parameters in the transverse momentum equation was performed to assess the sensitivity of results to their assumed values. It is confirmed that effects of these parameters on the overall results are not significant under PWR operating conditions. Data on subchannel properties of quality and mass flux were also assessed. From the data comparisons, it is evident that COBRA can successfully predict the PWR normal operating conditions but cannot predict the trend under bulk quality conditions

PWR: 10 years after and perspectives

International Nuclear Information System (INIS)

1990-01-01

These proceedings of the SFEN days on PWR (Ten years after and perspectives) comprise 13 conferences bearing on: - From the occurential approach to the state approach - Evolution of calculating tools - Human factors and safety - Reactor safety in the PWR 2000 - The PWR and the electrical power grid load follow - Fuel aspect of PWR management - PWR chemistry evolution - Balance of radiation protection - PWR modifications balance and influence on reactor operation - Design and maintenance of reactor components: 4 conferences [fr

Comprehensive exergetic and economic comparison of PWR and hybrid fossil fuel-PWR power plants

International Nuclear Information System (INIS)

Sayyaadi, Hoseyn; Sabzaligol, Tooraj

2010-01-01

A typical 1000 MW Pressurized Water Reactor (PWR) nuclear power plant and two similar hybrid 1000 MW PWR plants operate with natural gas and coal fired fossil fuel superheater-economizers (Hybrid PWR-Fossil fuel plants) are compared exergetically and economically. Comparison is performed based on energetic and economic features of three systems. In order to compare system at their optimum operating point, three workable base case systems including the conventional PWR, and gas and coal fired hybrid PWR-Fossil fuel power plants considered and optimized in exergetic and exergoeconomic optimization scenarios, separately. The thermodynamic modeling of three systems is performed based on energy and exergy analyses, while an economic model is developed according to the exergoeconomic analysis and Total Revenue Requirement (TRR) method. The objective functions based on exergetic and exergoeconomic analyses are developed. The exergetic and exergoeconomic optimizations are performed using the Genetic Algorithm (GA). Energetic and economic features of exergetic and exergoeconomic optimized conventional PWR and gas and coal fired Hybrid PWR-Fossil fuel power plants are compared and discussed comprehensively.

Measured performance of four PWR liquid radioactive waste treatment systems

International Nuclear Information System (INIS)

McIsaac, C.V.; Mandler, J.W.; Stalker, A.C.

1980-01-01

This paper presents results of a study of the liquid radwaste treatment and boron recovery systems of four operating PWR power plants. The performance of a given system was determined from measurements of radionuclide inventories in samples drawn from demineralizers, evaporators, filters, and gaseous cleanup systems. The plants at which measurements were made are Fort Calhoun, Zion 1 and 2, Turkey Point 3 and 4, and Rancho Seco

Preliminary analysis of a large 1600 MWe PWR core loaded with 30% MOX fuel

International Nuclear Information System (INIS)

Polidoro, Franco; Corsetti, Edoardo; Vimercati, Giuliano

2011-01-01

The paper presents a full-core 3-D analysis of the performances of a large 1600 MWe PWR core, loaded with 30% MOX fuel, in accordance with the European Utility Requirements (EUR). These requirements state that the European next generation power plants have to be designed capable to use MOX (UO 2 - PuO 2 ) fuel assemblies up to 50% of the core, together with UO 2 fuel assemblies. The use of MOX assemblies has a significant impact on key physic parameters and on safety. A lot of studies have been carried out in the past to explore the feasibility of plutonium recycling strategies by loading LWR reactors with MOX fuel. Many of these works were based on lattice codes, in order to perform detailed analyses of the neutronic characteristics of MOX assemblies. With the aim to take into account their interaction with surrounding UO 2 fuel elements, and the global effects on the core at operational conditions, an integrated approach making use of a 3-D core simulation is required. In this light, the present study adopts the state-of-art numerical models CASMO-5 and SIMULATE-3 to analyze the behavior of the core fueled with 30% MOX and to compare it with that of a large PWR reference core, fueled with UO 2 . (author)

Modal testing and identification of a PWR fuel assembly

International Nuclear Information System (INIS)

Pisapia, S.; Collard, B.; Mori, V.; Bellizzi, S.

2003-01-01

This study aims at characterizing the vibratory behavior of a full-scale fuel assembly using an experimental approach. The effect of the assembly environment (air, stagnant water, and water under flow) is studied. The analysis of the test series shows that the vibratory behavior of full-scale fuel assembly is strongly nonlinear. An identification phase, based on temporal mean square criterion, allows us to obtain a nonlinear model representative of the first vibration mode of a fuel assembly. The selected class of models including damping and stiffness nonlinear terms is efficient in air, in stagnant water, and in water under flow. In all environments, the stiffness decreases with the displacement level and the damping increases with the velocity level. In the presence of water, the damping goes up and increases again with flowrate. (author)

Fuel assemblies for PWR type reactors: fuel rods, fuel plates. CEA work presentation

International Nuclear Information System (INIS)

Delafosse, Jacques.

1976-01-01

French work on PWR type reactors is reported: basic knowledge on Zr and its alloys and on uranium oxide; experience gained on other programs (fast neutron and heavy water reactors); zircaloy-2 or zircaloy-4 clad UO 2 fuel rods; fuel plates consisting of zircaloy-2 clad UO 2 squares of thickness varying between 2 and 4mm [fr

PIE of test assembly of Qinshan nuclear power plant

International Nuclear Information System (INIS)

Ran, M.; Yan, J.; Wang, S.

2000-01-01

The small dimensional test fuel assembly (3x3-2) for the Qinshan Nuclear Power Plant was irradiated up to 25.7 Gwd/tU in the in-pile loop (15.5 Mpa,320 C) in Heavy Water Research Reactor (HWRR), CIAE, at simulative condition to Qinshan PWR normal and short time overpower operation for verifying the design, technology, and material properties of the fuel assembly. Comprehensive post-irradiation examination (PIE) including dimension measurement, gamma scanning, eddy current test, X ray, radiography, measurement of fission gas release, and quantitative metallography etc. were performed. PIE results show that the diameter of the fuel rods changed, ridges appeared on the cladding, pellets swelled, and the rate of fission gas release was higher than what we expected. The results would be an important basis for further improvement of design, technology and material properties for Qinshan PWR assembly. (author)

Heterogeneous assembly for plutonium multi recycling in PWRs: the Corail concept

International Nuclear Information System (INIS)

Youinou, G.; Zaetta, A.; Vasile, A.; Delpech, M.; Rohart, M.; Guillet, J.L.

2001-01-01

The CORAIL assembly is a standard 17 x 17 PWR fuel assembly containing 180 UO 2 rods and 84 MOX rods located at the periphery to limit the hot-channel factor. After many recycling, the plutonium content stabilizes around 8% and the U 235 enrichment around 4.8% (for a 3 u 15000 MWd/t fuel cycle length). An all-CORAIL park would have a zero plutonium mass balance, and compared with an all-UO 2 park the gain in terms of Separating Work Units and natural uranium would be between 15% and 20%. Detailed calculations of a 1300 MWe PWR loaded with such assemblies show that its control would not require the use of enriched boron. Burnable poison is necessary to limit the hot-channel factor. (author)

Control in fabrication of PWR and BWR type reactor fuel elements

International Nuclear Information System (INIS)

Gorskij, V.V.

1981-01-01

Both destructive and non-destructive testing methods now in use in fabrication of BWR and PWR type reactor fuel elements at foreign plants are reviewed. Technological procedures applied in fabrication of fuel elements and fuel assemblies are described. Major attention is paid to radiographic, ultrasonic, metallographic, visual and autoclavic testings. A correspondence of the methods applied to the ASTM standards is discussed. The most part of the countries are concluded the apply similar testing methods enabling one to reliably evaluate the quality of primary materials and fabricated fuel elements and thus meeting the demands to contemporary PWR and BWR type reactor fuel elements. Practically all fuel element and pipe fabrication plants in Western Europe, Asia and America use the ASTM standards as the basis for the quality contr [ru

Control rod ejection accident analysis for a PWR with thorium fuel loading

Energy Technology Data Exchange (ETDEWEB)

Da Cruz, D.F. [Nuclear Research and Consultancy Group NRG, Westerduinweg 3, P.O. Box 25, 1755 ZG Petten (Netherlands)

2010-07-01

This paper presents the results of 3-D transient analysis of a pressurized water reactor (PWR) core loaded with 100% Th-Pu MOX fuel assemblies. The aim of this study is to evaluate the safety impact of applying a full loading of this innovative fuel in PWRs of the current generation. A reactivity insertion accident scenario has been simulated using the reactor core analysis code PANTHER, used in conjunction with the lattice code WIMS. A single control rod assembly, with the highest reactivity worth, has been considered to be ejected from the core within 100 milliseconds, which may occur due to failure of the casing of the control rod driver mechanism. Analysis at both hot full power and hot zero power reactor states have been taken into account. The results were compared with those obtained for a representative PWR fuelled with UO{sub 2} fuel assemblies. In general the results obtained for both cores were comparable, with some differences associated mainly to the harder neutron spectrum observed for the Th-Pu MOX core, and to some specific core design features. The study has been performed as part of the LWR-DEPUTY project of the EURATOM 6. Framework Programme, where several aspects of novel fuels are being investigated for deep burning of plutonium in existing nuclear power plants. (authors)

Radioactive waste processing

International Nuclear Information System (INIS)

Dejonghe, P.

1978-01-01

This article gives an outline of the present situation, from a Belgian standpoint, in the field of the radioactive wastes processing. It estimates the annual quantity of various radioactive waste produced per 1000 MW(e) PWR installed from the ore mining till reprocessing of irradiated fuels. The methods of treatment concentration, fixation, final storable forms for liquid and solid waste of low activity and for high level activity waste. The storage of radioactive waste and the plutonium-bearing waste treatement are also considered. The estimated quantity of wastes produced for 5450 MW(e) in Belgium and their destination are presented. (A.F.)

A comparison study on radioactive waste management effectiveness in various nuclear fuel cycles

International Nuclear Information System (INIS)

Ko, Won Il; Kim, Ho Dong

2001-07-01

This study examines whether the DUPIC (Direct Use of Spent PWR Fuel In CANDU) fuel cycle make radioactive waste management more effective, by comparing it with other fuel cycles such as the PWR (Pressurized Water Reactor) once-through cycle, the HWR (Pressurized Heavy Water Reactor) once-through cycle and the thermal recycling option to use an existing PWR with MOX (Mixed Oxide) fuel. This study first focuses on the radioactive waste volume generated in all fuel cycle steps, which could be one of the measures of effectiveness of the waste management. Then the total radioactive waste disposition cost is estimated based on two units measuring; m3/GWe-yr and US$/GWe-yr. We find from the radioactive waste volume estimation that the DUPIC fuel cycle could have lower volumes for milling tailings, low level waste and spent fuel than those of other fuel cycle options. From the results of the disposition cost analysis, we find that the DUPIC waste disposition cost is the lowest among fuel cycle options. If the total waste disposition cost is used as a proxy for quantifying the easiness or difficulty in managing wastes, then the DUPIC option actually make waste management easier

Minimization of PWR reactor control rods wear

International Nuclear Information System (INIS)

Ponzoni Filho, Pedro; Moura Angelkorte, Gunther de

1995-01-01

The Rod Cluster Control Assemblies (RCCA's) of Pressurized Water Reactors (PWR's) have experienced a continuously wall cladding wear when Reactor Coolant Pumps (RCP's) are running. Fretting wear is a result of vibrational contact between RCCA rodlets and the guide cards which provide lateral support for the rodlets when RCCA's are withdrawn from the core. A procedure is developed to minimize the rodlets wear, by the shuffling and axial reposition of RCCA's every operating cycle. These shuffling and repositions are based on measurement of the rodlet cladding thickness of all RCCA's. (author). 3 refs, 2 figs, 2 tabs

Bituminization of simulated PWR type reactor wastes, boric evaporator bottons and ion exchange resins, carried out in CNEN/SP using commercial bitumen available in the Brazilian market

International Nuclear Information System (INIS)

Grosche Filho, C.E.; Chandra, U.

1986-01-01

The first results of the study of bituminization of simulated PWR wastes, boric evaporator bottons and spent ion-exclange resins (OH - , H + ) and incinerated ash-wates are presented and discussed. The study consisted of characterization of the commercial bitumen, locally available and bitumen wastes products of varying whight compositions. The characterization was carried out using standard analysis methods of ABNT and ASTM, and included measurement of, penetration, softening point and flash point. In addition, the bitumen samples were analized for their resin and asphaltene contents. For leaching studies, wastes products of bitumen and resin loaded with 134 Cs were utilized. The method used was according to the ISO norms. The simulation of the industrial process was carried out using an extruder-evaporator typically used in the plastic industries offered by Industria de Maquinas Miotto Ltda., Sao Bernardo do Campo - SP. (Author) [pt

Maturity of the PWR

International Nuclear Information System (INIS)

Bacher, P.; Rapin, M.; Aboudarham, L.; Bitsch, D.

1983-03-01

Figures illustrating the predominant position of the PWR system are presented. The question is whether on the basis of these figures the PWR can be considered to have reached maturity. The following analysis, based on the French program experience, is an attempt to pinpoint those areas in which industrial maturity of the PWR has been attained, and in which areas a certain evolution can still be expected to take place

The PWR cores management

International Nuclear Information System (INIS)

Barral, J.C.; Rippert, D.; Johner, J.

2000-01-01

During the meeting of the 25 january 2000, organized by the SFEN, scientists and plant operators in the domain of the PWR debated on the PWR cores management. The five first papers propose general and economic information on the PWR and also the fast neutron reactors chains in the electric power market: statistics on the electric power industry, nuclear plant unit management, the ITER project and the future of the thermonuclear fusion, the treasurer's and chairman's reports. A second part offers more technical papers concerning the PWR cores management: performance and optimization, in service load planning, the cores management in the other countries, impacts on the research and development programs. (A.L.B.)

Interpretation of out of line control rod experiments for 1300 MWE PWR

Energy Technology Data Exchange (ETDEWEB)

Leroy, J.L.; Garcia-Fernandez, L.

1988-01-01

The present note summarizes the studies we performed recently in order to search a 2D reconstruction procedure for the 1300 MWE PWR power shape, starting from data coming out from thermocouples placed on several fuel assemblies. In classical PWR design, only a few assemblies are equipped with measurement devices, so that it is necessary to interpolate among measure points in order to obtain a complete coverage of the core. A mathematical approach based on the splitting of the power into a reference steady state nominal shape and some ''influence'' and harmonic functions was chosen. The reference steady state power shape, which corresponds to the full power operating mode, is obtained via direct mobile chamber measurements. The perturbations due to the control rod movements are accounted for by specific ''influence'' functions: moreover, harmonics are used to reconstruct the minor effects due to xenon tilts, rod out of line positions and all actual mechanical and thermohydraulic inhomogeneities. The weighting coefficients of the functions are evaluated by a least square method, starting from the distribution of the deviations among the measurements and the reference values.

Construction and utilization of linear empirical core models for PWR in-core fuel management

International Nuclear Information System (INIS)

Okafor, K.C.

1988-01-01

An empirical core-model construction procedure for pressurized water reactor (PWR) in-core fuel management is developed that allows determining the optimal BOC k ∞ profiles in PWRs as a single linear-programming problem and thus facilitates the overall optimization process for in-core fuel management due to algorithmic simplification and reduction in computation time. The optimal profile is defined as one that maximizes cycle burnup. The model construction scheme treats the fuel-assembly power fractions, burnup, and leakage as state variables and BOC zone enrichments as control variables. The core model consists of linear correlations between the state and control variables that describe fuel-assembly behavior in time and space. These correlations are obtained through time-dependent two-dimensional core simulations. The core model incorporates the effects of composition changes in all the enrichment control zones on a given fuel assembly and is valid at all times during the cycle for a given range of control variables. No assumption is made on the geometry of the control zones. A scatter-composition distribution, as well as annular, can be considered for model construction. The application of the methodology to a typical PWR core indicates good agreement between the model and exact simulation results

APA: U free Pu pin in a heterogeneous assembly to improve Pu loading in a PWR - neutronic, thermo-hydraulic and manufacturing studies

International Nuclear Information System (INIS)

Porta, J.; Puill, A.; Bauer, M.; Matheron, P.

1999-01-01

After having presented the specific context of France with respect to the fuel cycle and reprocessing, the problem of plutonium fuel utilization is posed. If one of the solutions, a pressurized water reactor (PWR) with an increased moderation ratio seems possible, it entails making excessive changes to the reactor, the control systems, and the general architecture of the steam supply system. Another solution consists in modifying the fuel itself so as to eliminate conversion on 238 U by using plutonium (Pu) in a neutronically inert matrix. However, the disadvantage of this type of fuel is that it has very low Doppler and draining coefficients and a very small delayed neutron fraction. To enable using these fuels, a heterogeneous assembly has to be defined, in which standard UO 2 rods provide the physical properties required to ensure acceptable safety coefficients. (author)

CFD simulation of a four-loop PWR at asymmetric operation conditions

Energy Technology Data Exchange (ETDEWEB)

Cheng, Jian-Ping; Yan, Li-Ming; Li, Feng-Chen, E-mail: lifch@hit.edu.cn

2016-04-15

Highlights: • A CFD numerical simulation procedure was established for simulating RPV of VVER-1000. • The established CFD approach was validated by comparing with available data. • Thermal hydraulic characteristics under asymmetric operation condition were investigated. • Apparent influences of the shutdown loop on its neighboring loops were obtained. - Abstract: The pressurized water reactor (PWR) with multiple loops may have abnormal working conditions with coolant pumps out of running in some loops. In this paper, a computational fluid dynamics (CFD) numerical study of the four-loop VVER-1000 PWR pressure vessel model was presented. Numerical simulations of the thermohydrodynamic characteristics in the pressure vessel were carried out at different inlet conditions with four and three loops running, respectively. At normal stead-state condition (four-loop running), different parameters were obtained for the full fluid domain, including pressure losses across different parts, pressure, velocity and temperature distributions in the reactor pressure vessel (RPV) and mass flow distribution of the coolant at the inlet of reactor core. The obtained results for pressure losses matched with the experimental reference values of the VVER-1000 PWR at Tianwan nuclear power plant (NPP). For most fuel assemblies (FAs), the inlet flow rates presented a symmetrical distribution about the center under full-loop operation conditions, which accorded with the practical distribution. These results indicate that it is now possible to study the dynamic transition process between different asymmetric operation conditions in a multi-loop PWR using the established CFD method.

Recent development for improving of PWR flexibility to load follow and frequency control operation

International Nuclear Information System (INIS)

Dubourg, M.

1983-08-01

In order to adjust the PWR electricity generation to the consumption network, new operating conditions were established. Those new conditions generate additional mechanical and thermal sollicitations due to the frequent motion of control rod banks, consisting of mechanical fatigue cycling and wear at the level of control rode drive mechanisms, control rods and guide tubes, wear and thermal fatigue cycling at the level of fuel assemblies. This paper presents the various aspects of this program including identification of the most critical areas of components, basic research in laboratories for resolving wear problems in PWR environment, improvement of local hydraulics for reducing loads, and endurance testing of full scale components on testing facilities

Reducing the radiotoxicity of PWR cladding hulls by cold-crucible melting

Energy Technology Data Exchange (ETDEWEB)

Berthier, P.; Boen, R.; Piccinato, R.; Ladirat, C.

1994-12-31

PWR cladding wastes from spent fuel reprocessing plants are highly radiotoxic due to the presence of long-lived alpha-emitting nuclides and certain beta-gamma emitters. Various options are now under consideration for disposal of such wastes. The ``Commissariat a l`Energie Atomique`` is now developing a melting process at Marcoule that promises to diminish their radiotoxicity. Work has focused on two complementary research areas: obtaining a high quality metallic containment matrix and achieving maximum decontamination by concentrating the plutonium and minor actinides together with cesium and strontium in the slag. Vitrification represents a short-term solution for the slag; from a longer-term perspective, this waste form is ideally suited for the SPIN programme. This is an indispensable step toward the possible implementation of an advanced waste management strategy involving actinide separation and transmutation to reduce the long-term nuclear waste disposal hazard. (author). 1 ref., 2 figs., 8 tabs.

NODAL3 Sensitivity Analysis for NEACRP 3D LWR Core Transient Benchmark (PWR

Directory of Open Access Journals (Sweden)

Surian Pinem

2016-01-01

Full Text Available This paper reports the results of sensitivity analysis of the multidimension, multigroup neutron diffusion NODAL3 code for the NEACRP 3D LWR core transient benchmarks (PWR. The code input parameters covered in the sensitivity analysis are the radial and axial node sizes (the number of radial node per fuel assembly and the number of axial layers, heat conduction node size in the fuel pellet and cladding, and the maximum time step. The output parameters considered in this analysis followed the above-mentioned core transient benchmarks, that is, power peak, time of power peak, power, averaged Doppler temperature, maximum fuel centerline temperature, and coolant outlet temperature at the end of simulation (5 s. The sensitivity analysis results showed that the radial node size and maximum time step give a significant effect on the transient parameters, especially the time of power peak, for the HZP and HFP conditions. The number of ring divisions for fuel pellet and cladding gives negligible effect on the transient solutions. For productive work of the PWR transient analysis, based on the present sensitivity analysis results, we recommend NODAL3 users to use 2×2 radial nodes per assembly, 1×18 axial layers per assembly, the maximum time step of 10 ms, and 9 and 1 ring divisions for fuel pellet and cladding, respectively.

The physical and chemical degradation of PWR fuel rods in severe accident conditions

International Nuclear Information System (INIS)

Parsons, P.D.; Mowat, J.A.S.; Dewhurst, D.W.F.; Hughes, T.E.

1983-01-01

An experimental study of the interaction between Zircaloy-4 cladding and UO 2 in PWR fuel rods heated to high temperatures with a negligible differential pressure across the cladding wall is described. The fuel rods were of dimensions appropriate to the 17x17 PWR fuel sub-assembly and were heated in a non-oxidising environment (vacuum) up to approx. 1850 deg. C either isothermally or through heating ramps. Observations were made concerning the extent and nature of the reaction zone between Zircaloy-4 and UO 2 over the temperature range 1500-1850 deg. C for times ranging from 1 min to 125 min. The location, morphology and the chemical composition of the phases formed are described along with the kinetics of their formation. (author)

A practical approach to burn-up credit use in package design approval for PWR uranium oxide spent fuel assemblies

International Nuclear Information System (INIS)

Kroger, H.; Reiche, I.

2009-01-01

TN International has applied for a license for the TN 24 E transport and storage cask with the German competent authority using a new Burn-up Credit (BUC) approach for PWR uranium oxide fuel assemblies based on actinides and six selected fission products. In order to enable the use of BUC for fission products, various experimental data have to be provided for the two important aspects of the criticality calculation. Firstly, post-irradiation examination (PIE) experiments for the verification of the calculated fission product concentrations have to be provided for each selected fission product. These data are then used to validate the depletion calculations. Secondly, experimental data for the criticality calculations in the form of critical benchmark experiments have to be provided. The submitted data will be investigated for their applicability to the TN 24 E transport and storage cask. Since the application is limited to six fission products only, the conservatism of the BUC approach can be further justified, as the reduction in reactivity from the remaining fission products (about 190) is not taken credit for. (authors)

The computer program ELCOM in the planning and structural analysis of PWR fuel elements: an example

International Nuclear Information System (INIS)

Silva Macedo, L.V. da

1990-01-01

Is's presented some results obtained with the ELCOM computer code, such as deflections, moments and natural frequencies, used in the design and structural analysis of PWR fuels assemblies. It's studied the behavior of these results varying the number of spacer grids, the rigidity of the joint between the fuel pin and the spacer grid, and the fuel assembly's boundary condition, considered in the analysis, in it's mounting into the core (if clamped-clamped, clamped-hinged or hinged-hinged). (author)

Development and application of integrated digital I and C system in Japanese PWR plants

International Nuclear Information System (INIS)

Tominaga, M.

1995-01-01

The Integrated Digital Instrumentation and Control (I and C) System has been developed and applied to non-safety grade I and C systems in the latest 5 Japanese PWR plants in 1990's. Based on the experience in these plants, the Integrated Digital I and C System will be planned to apply also to safety grade I and C systems in Advanced PWR (APWR) as the overall application of digital technology. The basic design task has been just started for APWR which is to be in commercial operation in early 2000's and under the development about various issues of safety grade digital I and C systems. On the other hand, in conventional Japanese PWR plants, digital I and C systems have been applied step by step since 1980's. For example, digital I and C systems for radio-active waste processing system have been adopted to 13 units, and dedicated digital I and C systems for Local loop control system to 8 units. The trend and status of development and application of the digital I and C systems, especially the Integrated Digital I and C System in Japanese PWR plants are presented. (5 refs., 4 figs.)

Waste Package Lifting Calculation

International Nuclear Information System (INIS)

H. Marr

2000-01-01

The objective of this calculation is to evaluate the structural response of the waste package during the horizontal and vertical lifting operations in order to support the waste package lifting feature design. The scope of this calculation includes the evaluation of the 21 PWR UCF (pressurized water reactor uncanistered fuel) waste package, naval waste package, 5 DHLW/DOE SNF (defense high-level waste/Department of Energy spent nuclear fuel)--short waste package, and 44 BWR (boiling water reactor) UCF waste package. Procedure AP-3.12Q, Revision 0, ICN 0, calculations, is used to develop and document this calculation

Waste Package and Material Testing for the Proposed Yucca Mountain High Level Waste Repository

International Nuclear Information System (INIS)

Doering, Thomas; Pasupathi, V.

2002-01-01

Over the repository lifetime, the waste package containment barriers will perform various functions that will change with time. During the operational period, the barriers will function as vessels for handling, emplacement, and waste retrieval (if necessary). During the years following repository closure, the containment barriers will be relied upon to provide substantially complete containment, through 10,000 years and beyond. Following the substantially complete containment phase, the barriers and the waste package internal structures help minimize release of radionuclides by aqueous- and gaseous-phase transport. These requirements have lead to a defense-in-depth design philosophy. A multi-barrier design will result in a lower breach rate distributed over a longer period of time, thereby ensuring the regulatory requirements are met. The design of the Engineered Barrier System (EBS) has evolved. The initial waste package design was a thin walled package, 3/8 inch of stainless steel 304, that had very limited capacity, (3 PWR and 4 BWR assemblies) and performance characteristics, 300 to 1,000 years. This design required over 35,000 waste packages compared to today's design of just over 10,000 waste packages. The waste package designs are now based on a defense-in-depth/multi-barrier philosophy and have a capacity similar to the standard storage and rail transported spent nuclear fuel casks. Concurrent with the development of the design of the waste packages, a comprehensive waste package materials testing program has been undertaken to support the selection of containment barrier materials and to develop predictive models for the long-term behavior of these materials under expected repository conditions. The testing program includes both long-term and short-term tests and the results from these tests combination with the data published in the open literature are being used to develop models for predicting performance of the waste packages

Organic diagenesis in commercial nuclear wastes

International Nuclear Information System (INIS)

Toste, A.P.; Lechner-Fish, T.J.

1988-01-01

The nuclear industry currently faces numerous challenges. Large volumes of already existing wastes must be permanently disposed using environmentally acceptable technologies. Numerous criteria must be addressed before wastes can be permanently disposed. Waste characterization is certainly one of the key criteria for proper waste management. some wastes are complex melting pots of inorganics, radiochemicals, and, occasionally, organics. It is clear, for example, that organics have been used extensively in nuclear operations, such as waste reprocessing, and continue to be used widely as solvents, decontamination agents, etc. The authors have analyzed the organic content of many kinds of nuclear wastes, ranging from commercial to defense wastes. In this paper, the finale analyses are described of three commercial wastes: one waste from a pressurized water reactor (PWR) and two wastes from a boiling water reactor (BWR). The PWR waste is a boric acid concentrate waste. The two BWR wastes, BWR wastes Nos. 1 and 2, are evaporator concentrates of liquid wastes produced during the regeneration of ion-exchange resins used to purify reactor process water. In preliminary analyses, which were reported previously, a few know organics and myriad unknowns were detected. Recent reexamination of mass-spectral data, coupled with reanalysis of the wastes, has resulted in the firm identification of the unknowns. Most of the compounds, over thirty distinct organics, are derived from the degradation, or diagenesis, of source-term organics, revealing, for the first time, that organic diagenesis in commercial wastes is both vigorous and varied

Acceptance of non-fuel assembly hardware by the Federal Waste Management System

International Nuclear Information System (INIS)

1990-03-01

This report is one of a series of eight prepared by E. R. Johnson Associates, Inc. (JAI) under ORNL's contract with DOE's OCRWM Systems Integration Program and in support of the Annual Capacity Report (ACR) Issue Resolution Process. The report topics relate specifically to the list of high-priority technical waste acceptance issues developed jointly by DOE and a utility-working group. JAI performed various analyses and studies on each topic to serve as starting points for further discussion and analysis leading eventually to finalizing the process by which DOE will accept spent fuel and waste into its waste management system. The eight reports are concerned with the conditions under which spent fuel and high-level waste will be accepted in the following categories: failed fuel; consolidated fuel and associated structural parts; non-fuel-assembly hardware; fuel in metal storage casks; fuel in multi-element sealed canisters; inspection and testing requirements for wastes; canister criteria; spent fuel selection for delivery; and defense and commercial high-level waste packages. 14 refs., 12 figs., 43 tabs

PWR thermocouple mechanical sealing structure

International Nuclear Information System (INIS)

Shen Qiuping; He Youguang

1991-08-01

The PWR in-core temperature detection device, which is one of measures to insure reactor safety operation, is to monitor and diagnose reactor thermal power output and in-core power distribution. The temperature detection device system uses thermocouples as measuring elements with stainless steel protecting sleeves. The thermocouple has a limited service time and should be replaced after its service time has reached. A new sealing device for the thermocouples of reactor in-core temperature detection system has been developed to facilitate replacement. The structure is complete tight under high temperature and pressure without any leakage and seepage, and easy to be assembled or disassembled in radioactive environment. The device is designed to make it possible to replace the thermocouple one by one if necessary. This is a new, simple and practical structure

Economic optimization of PWR cores with ROSA

International Nuclear Information System (INIS)

Verhagen, F.C.M.; Wakker, P.H.

2005-01-01

The core-loading pattern is decisive for fuel cycle economics, fuel safety parameters and economic planning for future cycles. ROSA, NRG's loading pattern optimization code system for PWRs, has proven for over a decade to be a valuable tool to reactor operators for improving their fuel management economics. ROSA uses simulated annealing as loading pattern optimization technique, in combination with an extremely fast 3-D neutronics code for loading pattern calculations. The code is continuously extended with new optimization parameters and rules. This paper outlines recent developments of the ROSA code system and discusses results of PWR specific applications of ROSA. Core designs with a large variety of challenging constraints have been realized with ROSA. As a typical example, for the 193 assembly, Vantage 5H/RFA-2 fueled TVA's Watts Bar unit 1, a cycle 4 core with 76 feed assemblies was designed. This was followed by a high-energy cycle 5 with only 77 feed assemblies and approximately 535 days of natural cycle length. Subsequently, an economical core using 72 bundles was designed for cycle 6. This resulted in considerable savings in the cost of feed assemblies for reloads. The typical accuracy of ROSA compared to results of license codes in within ±0.02 for normalized assembly powers, ±0.03 for maximum enthalpy rise hot channel factor (F ΔH ), and ±3 days for natural cycle length. (author)

PWR core follow calculations using the ELCOS code system

International Nuclear Information System (INIS)

Grimm, P.; Paratte, J.M.

1990-01-01

The ELCOS code system developed at PSI is used to simulate a cycle of a PWR in which one fifth of the assemblies are MOX fuel. The reactor and the calculational methods are briefly described. The calculated critical boron concentrations and power distributions are compared with the measurements at the plant. Although the critical boron concentration is somewhat overpredicted and the computed power distributions are slightly flatter than the measured ones the results of the calculations agree generally well with the measured data. (author) 1 tab., 8 figs., 6 refs

Experimentation, modelling and simulation of water droplets impact on ballooned sheath of PWR core fuel assemblies in a LOCA situation

International Nuclear Information System (INIS)

Lelong, Franck

2010-01-01

In a pressurized water reactor (PWR), during a Loss Of Coolant Accident (LOCA), liquid water evaporates and the fuel assemblies are not cooled anymore; as a consequence, the temperature rises to such an extent that some parts of the fuel assemblies can be deformed resulting in 'ballooned regions'. When reflooding occurs, the cooling of these partially blocked parts of the fuel assemblies will depend on the coolant flow that is a mixture of overheated vapour and under-saturated droplets. The aim of this thesis is to study the heat transfer between droplets and hot walls of the fuel rods. In this purpose, an experimental device has been designed in accordance with droplets and wall features (droplet velocity and diameter, wall temperature) representative of LOCA conditions. The cooling of a hot Nickel disk, previously heated by induction, is cooled down by a stream of monodispersed droplet. The rear face temperature profiles are measured by infrared thermography. Then, the estimation of wall heat flux is performed by an inverse conduction technique from these infrared images. The effect of droplet dynamical properties (diameter, velocity) on the heat flux is studied. These experimental data allow us to validate an analytical model of heat exchange between droplet and hot slab. This model is based on combined dynamical and thermal considerations. On the one hand, the droplet dynamics is considered through a spring analogy in order to evaluate the evolution of droplet features such as the spreading diameter when the droplet is squeezed over the hot surface. On the other hand, thermal parameters, such as the thickness of the vapour cushion beneath the droplet, are determined from an energy balance. In the short term, this model will be integrated in a CFD code (named NEPTUNE-CFD) to simulate the cooling of a reactor core during a LOCA, taking into account the droplet/wall heat exchange. (author)

Composition and Distribution of Tramp Uranium Contamination on BWR and PWR Fuel Rods

International Nuclear Information System (INIS)

Schienbein, Marcel; Zeh, Peter; Hurtado, Antonio; Rosskamp, Matthias; Mailand, Irene; Bolz, Michael

2012-09-01

In a joint research project of VGB and AREVA NP GmbH the behaviour of alpha nuclides in nuclear power plants with light water reactors has been investigated. Understanding the source and the behaviour of alpha nuclides is of big importance for planning radiation protection measures for outages and upcoming dismantling projects. Previous publications have shown the correlation between plant specific alpha contamination of the core and the so called 'tramp fuel' or 'tramp uranium' level which is linked to the defect history of fuel assemblies and accordingly the amount of previously washed out fuel from defective fuel rods. The methodology of tramp fuel estimation is based on fission product concentrations in reactor coolant but also needs a good knowledge of tramp fuel composition and in-core distribution on the outer surface of fuel rods itself. Sampling campaigns of CRUD deposits of irradiated fuel assemblies in different NPPs were performed. CRUD analyses including nuclide specific alpha analysis have shown systematic differences between BWR and PWR plants. Those data combined with literature results of fuel pellet investigations led to model improvements showing that a main part of fission products is caused by fission of Pu-239 an activation product of U-238. CRUD investigations also gave a better picture of the in-core composition and distribution of the tramp uranium contamination. It was shown that the tramp uranium distribution in PWR plants is time dependent. Even new fuel assemblies will be notably contaminated after only one cycle of operation. For PWR applies the following logic: the higher the local power the higher the contamination. With increasing burnup the local rod power usually decreases leading to decreasing tramp uranium contamination on the fuel rod surface. This is not applicable for tramp uranium contamination in BWR. CRUD contamination (including the tramp fuel deposits) is much more fixed and is constantly increasing

Modeling for speciation of radionuclides in waste packages with high-level radioactive wastes; Modellierung zur Speziation von Radionukliden in Abfallgebinden mit hoch radioaktiven Abfaellen

Energy Technology Data Exchange (ETDEWEB)

Weyand, Torben; Bracke, Guido; Seher, Holger

2016-10-15

Based on a literature search on radioactive waste inventories adequate thermodynamic data for model inventories were derived for geochemical model calculations using PHREEQC in order to determine the solid phase composition of high-level radioactive wastes in different containers. The calculations were performed for different model inventories (PWR-MOX, PWR-UO2, BWR-MOX, BMR-UO2) assuming intact containers under reduction conditions. The effect of a defect in the container on the solid phase composition was considered in variation calculations assuming air contact induced oxidation.

The new lattice code Paragon and its qualification for PWR core applications

International Nuclear Information System (INIS)

Ouisloumen, M.; Huria, H.C.; Mayhue, L.T.; Smith, R.M.; Kichty, M.J.; Matsumoto, H.; Tahara, Y.

2003-01-01

Paragon is a new two-dimensional transport code based on collision probability with interface current method and written entirely in Fortran 90/95. The qualification of Paragon has been completed and the results are very good. This qualification included a number of critical experiments. Comparisons to the Monte Carlo code MCNP for a wide variety of PWR assembly lattice types were also performed. In addition, Paragon-based core simulator models have been compared against PWR plant startup and operational data for a large number of plants. Some results of these calculations and also comparisons against models developed with a licensed Westinghouse lattice code, Phoenix-P, are presented. The qualification described in this paper provided the basis for the qualification of Paragon both as a validated transport code and as the nuclear data source for core simulator codes

PWR fuel inspection and repair technology development in the Republic of Korea

International Nuclear Information System (INIS)

Park, J.Y.

1998-01-01

As of September 1997, 10 PWRs and 2 PHWRs generate 10,320MW electricity in Korea. And another 8 PWRs and 2 PHWRs will be constructed by 2006. These will need about 400 MTU of PWR fuels and 400 MTU of PHWR fuels. To improve average burnup, thermal power, fuel usability and plant safety, better poolside fuel service technologies are strongly recommended as well as the fuel design and fabrication technology improvements. During the last twenty years of nuclear power plant operation in Korea, more than 4,000 fuel assemblies has been used. At the site, continuous coolant activity measurement, pool-side visual inspection and ultrasonic tests have been performed. Some of the fuels are damaged or failed for various reasons. Some of the defected fuels were examined in hot cell to investigate the cause of failure. Even though 30 PWR fuel assemblies were repaired by foreign engineers, fuel inspection and repair technologies are not established yet. Various kind of design for the fuel make the inspection, repair and reconstitution equipment more complex. As a result, recently, a plant to obtain overall technology for poolside fuel inspection, failed fuel repair and reconstitution through R and D activities are set forth. (author)

Preliminary study on direct recycling of spent PWR fuel in PWR system

International Nuclear Information System (INIS)

Waris, Abdul; Nuha; Novitriana; Kurniadi, Rizal; Su'ud, Zaki

2012-01-01

Preliminary study on direct recycling of PWR spent fuel to support SUPEL (Straight Utilization of sPEnt LWR fuel in LWR system) scenario has been conducted. Several spent PWR fuel compositions in loaded PWR fuel has been evaluated to obtain the criticality of reactor. The reactor can achieve it criticality for U-235 enrichment in the loaded fresh fuel is at least 4.0 a% with the minimum fraction of the spent fuel in the core is 15.0 %. The neutron spectra become harder with the escalating of U-235 enrichment in the loaded fresh fuel as well as the amount of the spent fuel in the core.

Siemens advance PWR fuel assemblies (HTP) and cladding

International Nuclear Information System (INIS)

Stout, R. B.; Woods, K. N.

1997-01-01

This paper describes the key features of the Siemens HTP (High Thermal Performance) fuel design, the current in-reactor performance of this advanced fuel assembly design, and the advanced cladding types available

Equipment for nondestructive testing of the PWR and BWR spept fUel elements and assemblies in the NPP storage pools

International Nuclear Information System (INIS)

Gorskij, V.V.

1983-01-01

Design features are considered of units for nondestructive testing of spent fUel elements and fuel assemblies (FA) in the storage pools of NPP with the PWR and BWR reactors. Units for remote viewing control of fuel element cans and FA, for direct measurements of their geometrical dimensions, for FA leak-testing, fuel element can nondestructive testing and gamma scanning, for measuring gaseous fission product pressure and fuel element free volume are described along with units for complex checking of fuel element and FA parameters. The units for nondestructive testing of spent fuel elements and EA are shown to differ both in their designs and a number of checked parameters of fuel elements and FA. The remote viewing and those for measuring the basic FA parameters are most generally employed. Units for complex testing of multiple fuel element parameters, designed in the last few years, are intended for operation with FA disassembled partially or fully and are characteristic of a high degree of computer measuring automation both for the process control and data processing

Implementation in free software of the PWR type university nucleo electric simulator (SU-PWR); Implementacion en software libre del simulador universitario de nucleoelectrica tipo PWR (SU-PWR)

Energy Technology Data Exchange (ETDEWEB)

Valle H, J.; Hidago H, F.; Morales S, J.B. [UNAM, Laboratorio de Analisis de Ingenieria de Reactores Nucleares DEPFI, Campus Morelos, en IMTA Jiutepec, Morelos (Mexico)]. e-mail: julfi_jg@yahoo.com.mx

2007-07-01

Presently work is shown like was carried out the implementation of the University Simulator of Nucleo-electric type PWR (SU-PWR). The implementation of the simulator was carried out in a free software simulation platform, as it is Scilab, what offers big advantages that go from the free use and without cost of the product, until the codes modification so much of the system like of the program with the purpose of to improve it or to adapt it to future routines and/or more advanced graphic interfaces. The SU-PWR shows the general behavior of a PWR nuclear plant (Pressurized Water Reactor) describing the dynamics of the plant from the generation process of thermal energy in the nuclear fuel, going by the process of energy transport toward the coolant of the primary circuit the one which in turn transfers this energy to the vapor generators of the secondary circuit where the vapor is expanded by means of turbines that in turn move the electric generator producing in this way the electricity. The pressurizer that is indispensable for the process is also modeled. Each one of these stages were implemented in scicos that is the Scilab tool specialized in the simulation. The simulation was carried out by means of modules that contain the differential equation that mathematically models each stage or equipment of the PWR plant. The result is a series of modules that based on certain entrances and characteristic of the system they generate exits that in turn are the entrance to other module. Because the SU-PWR is an experimental project in early phase, it is even work and modifications to carry out, for what the models that are presented in this work can vary a little the being integrated to the whole system to simulate, but however they already show clearly the operation and the conformation of the plant. (Author)

Thermo-mechanical analysis of PWR bolts susceptible to IASCC

International Nuclear Information System (INIS)

Matteoli, C.; Hannink, M.H.C.; Blom, F.J.; Marck, S.C. van der; Charpin-Jacobs, F.

2015-01-01

Irradiation Assisted Stress Corrosion Cracking (IASCC) is considered a primary ageing issue for the Reactor Pressure Vessel (RPV) internals of Pressurized Water Reactors (PWR). In particular, this complex phenomenon which develops in an environment featuring thermal and mechanical stresses, interaction with corrosive compounds and irradiation, is affecting the bolts connecting the baffles and the formers in the Nuclear Power Plants' RPVs. The baffle-former assembly is the structure that borders the fuel assemblies region, contributing to keep them in position and separating in the radial direction, the core region from the downcomer region. An evaluation of the stresses and temperatures reached in the baffle-former bolts during normal operation was performed by means of a coupled thermo-mechanical study which uses reactor physics calculations to obtain the fluence in the reactor core and as a consequence the heat deposition in the RPV internals. The heat deposition data are coupled with a finite element model of the bolts and the RPV internals in order to perform a complete analysis taking in account thermal, mechanical and radiation loadings. The study is first carried out focusing on a section of the RPV internals, showing a single row of baffle-former bolts. Then the work is extended to the full core height. The model set up in this work, includes an in-depth study of the behavior of the core internals, in particular baffle-former bolts. The model has the capability of understanding the mechanical and thermal behavior of essential internal components in a PWR. (authors)

Special points of view about development and construction of a PWR

International Nuclear Information System (INIS)

Meyer, P.J.

1977-01-01

1.0) The reactor core and its components, 1.1) design of the fuel assemblies, 1.2) incore instrumentation, 2.0) reactor pressure vessel with internals, 3.0) components of the reactor coolant loops, 3.1) steam generator, 3.2) pressurizer, 3.3) pressurizer relief tank, 3.4) reactor coolant pumps, 4.0) instrumentation and control of a PWR, 4.1) ex-core measuring system, 4.2) reactor protection system, 4.3) control systems, 4.4) radiation monitoring. (orig.) [de

Next generation PWR

International Nuclear Information System (INIS)

Tanaka, Toshihiko; Fukuda, Toshihiko; Usui, Shuji

2001-01-01

Development of LWR for power generation in Japan has been intended to upgrade its reliability, safety, operability, maintenance and economy as well as to increase its capacity in order, since nuclear power generation for commercial use was begun on 1970, to steadily increase its generation power. And, in Japan, ABWR (advanced BWR) of the most promising LWR in the world, was already used actually and APWR (advanced PWR) with the largest output in the world is also at a step of its actual use. And, development of the APWR in Japan was begun on 1980s, and is at a step of plan on construction of its first machine at early of this century. However, by large change of social affairs, economy of nuclear power generation is extremely required, to be positioned at an APWR improved development reactor promoted by collaboration of five PWR generation companies and the Mitsubishi Electric Co., Ltd. Therefore, on its development, investigation on effect of change in social affairs on nuclear power stations was at first carried out, to establish a design requirement for the next generation PWR. Here were described on outline, reactor core design, safety concept, and safety evaluation of APWR+ and development of an innovative PWR. (G.K.)

Glass melter assembly for the Hanford Waste Vitrification Plant

International Nuclear Information System (INIS)

Chen, A.E.; Russell, A.; Shah, K.R.; Kalia, J.

1993-01-01

The Hanford Waste Vitrification Plant (HWVP) is designed to solidify high level radioactive waste by converting it into stable borosilicate after mixing with glass frit and water. The heart of this conversion process takes place in the glass melter. The life span of the existing melter is limited by the possible premature failure of the heater assembly, which is not remotely replaceable, in the riser and pour spout. A goal of HWVP Project is to design remotely replaceable riser and pour spout heaters so that the useful life of the melter can be prolonged. The riser pour spout area is accessible only by the canyon crane and impact wrench. It is also congested with supporting frame members, service piping, electrode terminals, canister positioning arm and other various melter components. The visibility is low and the accessibility is limited. The problem is further compounded by the extreme high temperature in the riser core and the electrical conductive nature of the molten glass that flows through it

The plutonium product: design of the rod and of the assembly

International Nuclear Information System (INIS)

Francillon, G.

1985-10-01

On the base of physical and experimental data the aim to be reached is to design a mixed oxide-fuel rod and a mixed oxide-fuel assembly which will be introduced in a PWR type reactor while ensuring the operation and safety of the unit required presently. This paper presents successively the MOX fuel rod and the MOX fuel assembly [fr

A Preliminary Design Study of Ultra-Long-Life SFR Cores having Heterogeneous Fuel Assemblies

Energy Technology Data Exchange (ETDEWEB)

Jung, GeonHee; You, WuSeung; Hong, Ser Gi [Kyung Hee University, Yongin (Korea, Republic of)

2016-10-15

The PWR and CANDU reactors have provided electricity for several decades in our country but they have produced lots of spent fuels and so the safe and efficient disposal of these spent fuels is one of the main issues in nuclear industry. This type ultra-long-life cores are quite efficient in terms of the amount of spent fuel generation per electricity production and they can be used as an interim storage for PWR or CANDU spent fuel over several tens of years if they use the PWR or CANDU spent fuel as the initial fuel. Typically, the previous works have considered radially homogeneous fuel assemblies in which only blanket or driver fuel rods are employed and they considered axially or radially heterogeneous core configurations with the radially homogeneous fuel assemblies. These core configurations result in the propagation of the power distribution which can lead to the significant temperature changes for each fuel assembly over the time. In this work, the radially heterogeneous fuel assemblies are employed in new ultra-long-life SFR (Sodium-cooled Fast Reactor) cores to minimize the propagation of power distribution by allowing the power propagation in the fuel assemblies. In this work, new small ultra-long life SFR cores were designed with heterogeneous fuel assemblies having both blanket and driver fuel rods to minimize the propagation of power distribution over the core by allowing power propagation from driver rods to blanket rods in fuel assemblies. In particular, high fidelity depletion calculation coupled with heterogeneous Monte Carlo neutron transport calculation was performed to assess the neutronic feasibility of the ultralong life cores. The results of the analysis showed that the candidate core has the cycle length of 77 EFPYs, a small burnup reactivity swing of 1590 pcm and acceptably small SVRs both at BOC and EOC.

Simulation model of dynamical behaviour of reactor fuel assemblies

International Nuclear Information System (INIS)

Planchard, J.

1994-01-01

This report briefly describes the homogenized dynamical equations of a tube bundle placed in a perfect irrotational fluid, on case of small displacements. This approach can be used to study the mechanical behaviour of fuel assemblies of PWR reactor submitted to earthquake or depressurization blow-down. The numerical calculations require to define the added mass matrix of the fuel assemblies, for which the principle of computation is presented. (author). 14 refs., 4 figs

PWR secondary water chemistry guidelines

International Nuclear Information System (INIS)

Bell, M.J.; Blomgren, J.C.; Fackelmann, J.M.

1982-10-01

Steam generators in pressurized water reactor (PWR) nuclear power plants have experienced tubing degradation by a variety of corrosion-related mechanisms which depend directly on secondary water chemistry. As a result of this experience, the Steam Generator Owners Group and EPRI have sponsored a major program to provide solutions to PWR steam generator problems. This report, PWR Secondary Water Chemistry Guidelines, in addition to presenting justification for water chemistry control parameters, discusses available analytical methods, data management and surveillance, and the management philosophy required to successfully implement the guidelines

AGR v PWR

International Nuclear Information System (INIS)

Green, D.

1986-01-01

When the Central Electricity Generating Board (CEGB) invited tenders and placed a contract for the Advanced Gas Cooled Reactor (AGR) at Dungeness B in 1965 -preferring it to the Pressurised Water Reactor (PWR) -the AGR was lamentably ill developed. The effects of the decision were widely felt, for it took the British nuclear industry off the light water reactor highway of world reactor business and up and idiosyncratic private highway of its own, excluding it altogether from any material export business in the two decades which followed. Yet although the UK may have made wrong decisions in rejecting the PWR in 1965, that does not mean that it can necessarily now either correct them, or redeem their consequence, by reversing the choice in 1985. In the 20 years since 1965 the whole world economic and energy picture has been transformed and the national picture with it. Picking up the PWR now could prove as big a disaster as rejecting it may have been in 1965. (author)

Fuel assembly for a nuclear reactor

Energy Technology Data Exchange (ETDEWEB)

Ferrari, H M; Miller, D L; Tong, L S

1973-09-06

The subject of the patent is a spacer design applicable, primarily, to LWR, and especially, though not specifically PWR, fuel assemblies. The spacer consists of an egg-box type of assembly formed of interlocking pressed plates giving a square lattice whose openings accommodate fuel pins or regulating rods. The pressed plates are formed to provide pressed-out spring-like flanges which hold the fuel pins in position and guide the regulating rods. Additional pressed-out flanges ensure the correct configuration of the spacer structure. The spacer is designed to present as little resistance as possible to coolant flow.

PWR and BWR light water reactor systems in the USA and their fuel cycle

International Nuclear Information System (INIS)

Crawford, W.D.

1977-01-01

Light water reactor operating experience in the USA can be considered to date from the choice of the pressurized water reactor (PWR) for use in the naval reactor program and the subsequent construction and operation of the nuclear power plant at Shippingport, Pennsylvania in 1957. The development of the boiling water reactor (BWR) in 1954 and its selection for the plant at Dresden, Illinois in 1959 established this concept as the other major reactor type in the US nuclear power program. The subsequent growth profile is presented, leading to 31 PWR's and 23 BWR's currently in operation as well as to plants in the planning and construction phase. A significant operating record has been accumulated concerning the availability of each of these reactor types as determined by: (1) outage for refueling, (2) component reliability, (3) maintenance requirements, and (4) retrofitting required by government regulation. In addition, the use and performance of BWR's and PWR's in meeting system load requirements is discussed. The growing concern regarding possible terrorist activities and other potential threats has resulted in systems and procedures designed to assure effective safeguards at nuclear power installations. Safeguards measures currently in place are described. Environmental effects of operating plants are subject to both radiological and non-radiological monitoring to verify that results are within the limits established in the licensing process. The operating results achieved and the types of modifications that have been required of operating plants by the Nuclear Regulatory Commission are reviewed. The PWR and BWR Fuel Cycle is examined in terms of: (1) fuel burnup experience and prospects for improvement, (2) the status and outlook for natural uranium resources, (3) enrichment capacity, (4) reprocessing and recycle, and the interrelationships among the latter three factors. High level waste management currently involving on-site storage of spent fuel is discussed

The waste management implications of decommissioning

International Nuclear Information System (INIS)

Passant, F.H.

1988-01-01

Decommissioning policy can only be framed in the light of radioactive waste management policy. What can be done with the waste materials, how and when, will determine the overall decommissioning plans and costs. In this paper the waste management options and their costs are reviewed for the decommissioning of the Central Electricity Generating Boards civil nuclear power stations. The paper concentrates on the decommissioning of Magnox stations, although comparative information on waste volumes and costs are given for the AGR programme and a typical PWR. (author)

Radioprotection and safety for a dry storage module for bare PWR fuel elements

International Nuclear Information System (INIS)

Tzontlimatzin, E.

1983-01-01

A module for dry storage of spent fuel from PWR, after a previous cooling time of 2 years, is examined. Biological protection is obtained by 185 cm of concrete. The safety study shows the impossibility of a fast increase in temperature in case of cooling system failure because in this case the module will be cooled by natural convection or thermosiphon. A project for a storage installation consisting of 5 modules for 1500 irradiated fuel assemblies is described [fr

Determination of uncertainties of PWR spent fuel radionuclide inventory based on real operational history data

Energy Technology Data Exchange (ETDEWEB)

Fast, Ivan; Bosbach, Dirk [Institute of Energy- and Climate Research, Nuclear Waste Management and Reactor Safety Research, IEK-6, Forschungszentrum, Julich GmbH, (Germany); Aksyutina, Yuliya; Tietze-Jaensch, Holger [German Product Control Office for Radioactive Waste (PKS), Institute of Energy- and Climate Research, Nuclear Waste Management and Reactor Safety Research, IEK-6, Forschungszentrum Julich GmbH, (Germany)

2015-07-01

A requisite for the official approval of the safe final disposal of SNF is a comprehensive specification and declaration of the nuclear inventory in SNF by the waste supplier. In the verification process both the values of the radionuclide (RN) activities and their uncertainties are required. Burn-up (BU) calculations based on typical and generic reactor operational parameters do not encompass any possible uncertainties observed in real reactor operations. At the same time, the details of the irradiation history are often not well known, which complicates the assessment of declared RN inventories. Here, we have compiled a set of burnup calculations accounting for the operational history of 339 published or anonymized real PWR fuel assemblies (FA). These histories were used as a basis for a 'SRP analysis', to provide information about the range of the values of the associated secondary reactor parameters (SRP's). Hence, we can calculate the realistic variation or spectrum of RN inventories. SCALE 6.1 has been employed for the burn-up calculations. The results have been validated using experimental data from the online database - SFCOMPO-1 and -2. (authors)

Determination of uncertainties of PWR spent fuel radionuclide inventory based on real operational history data

International Nuclear Information System (INIS)

Fast, Ivan; Bosbach, Dirk; Aksyutina, Yuliya; Tietze-Jaensch, Holger

2015-01-01

A requisite for the official approval of the safe final disposal of SNF is a comprehensive specification and declaration of the nuclear inventory in SNF by the waste supplier. In the verification process both the values of the radionuclide (RN) activities and their uncertainties are required. Burn-up (BU) calculations based on typical and generic reactor operational parameters do not encompass any possible uncertainties observed in real reactor operations. At the same time, the details of the irradiation history are often not well known, which complicates the assessment of declared RN inventories. Here, we have compiled a set of burnup calculations accounting for the operational history of 339 published or anonymized real PWR fuel assemblies (FA). These histories were used as a basis for a 'SRP analysis', to provide information about the range of the values of the associated secondary reactor parameters (SRP's). Hence, we can calculate the realistic variation or spectrum of RN inventories. SCALE 6.1 has been employed for the burn-up calculations. The results have been validated using experimental data from the online database - SFCOMPO-1 and -2. (authors)

The coupling of the Star-Cd software to a whole-core neutron transport code Decart for PWR applications

International Nuclear Information System (INIS)

Thomas, J.W.; Lee, H.C.; Downar, T.J.; Sofu, T.; Weber, D.P.; Joo, H.G.; Cho, J.Y.

2003-01-01

As part of a U.S.- Korea collaborative U.S. Department of Energy INERI project, a comprehensive high-fidelity reactor-core modeling capability is being developed for detailed analysis of existing and advanced PWR reactor designs. An essential element of the project has been the development of an interface between the computational fluid dynamics (CFD) module, STAR-CD, and the neutronics module, DeCART. Since the computational mesh for CFD and neutronics calculations are generally different, the capability to average and decompose data on these different meshes has been an important part of code coupling activities. An averaging process has been developed to extract neutronics zone temperatures in the fuel and coolant and to generate appropriate multi group cross sections and densities. Similar procedures have also been established to map the power distribution from the neutronics zones to the mesh structure used in the CFD module. Since MPI is used as the parallel model in STAR-CD and conflicts arise during initiation of a second level of MPI, the interface developed here is based on using TCP/IP protocol sockets to establish communication between the CFD and neutronics modules. Preliminary coupled calculations have been performed for PWR fuel assembly size problems and converged solutions have been achieved for a series of steady-state problems ranging from a single pin to a 1/8 model of a 17 x 17 PWR fuel assembly. (authors)

Survey of the power ramp performance testing of KWU'S PWR UO 2, fuel

Science.gov (United States)

Ga¨rtner, M.; Fischer, G.

1987-06-01

To determine the power ramp performance of KWU's PWR UO 2 fuel, 134 fuel rodlets with burnups of up to 46 GWd/ t (U) and several fuel assemblies with 19 to 30 GWd/t (U) burnup were ramped in power in the research reactors HFR Petten/The Netherlands and R2 Studsvik/Sweden and in the power plants KWO and KWB-A/Germany, respectively. The power ramp tests demonstrate decreasing resistance of the PWR fuel rods to PCI (pellet-to-clad interaction) up to fuel burnups of 35 GWd/t (U) and a reversal effect at higher burnups. The fuel rods can be operated free of defects at fast power transients to linear heat generation rates of up to 400 W/cm, at least.Power levels of up to 490 W/cm can be reached without defects by reducing the ramp rate. After reshuffling according to an out-in scheme, 1-cycle fuel assemblies may return to rod powers of up to 480 W/cm with a power increase rate of up to 10 W/(cm min) without fuel rod damage. Set points basing on these test results and incorporated into the power distribution control and power density limitation system of KWU's advanced power plants guarantee safe plant operation under normal and load follow operating conditions.

Fuel assemblies for use in nuclear reactors

International Nuclear Information System (INIS)

Mochida, Takaaki.

1987-01-01

Purpose: To increase the plutonium utilization amount and improve the uranium-saving effect in the fuel assemblies of PWR type reactor using mixed uranium-plutonium oxides. Constitution: MOX fuel rods comprising mixed plutonium-uranium oxides are disposed to the outer circumference of a fuel assembly and uranium fuel rods only composed of uranium oxides are disposed to the central portion thereof. In such a fuel assembly, since the uranium fuel rods are present at the periphery of the control rod, the control rod worth is the same as that of the uranium fuel assembly in the prior art. Further, since about 25 % of the entire fuel rods is composed of the MOX fuel rods, the plutonium utilization amount is increased. Further, since the MOX fuel rods at low enrichment degree are present at the outer circumferential portion, mismatching at the boundary to the adjacent MOX fuel assembly is reduced and the problem of local power peaking increase in the MOX fuel assembly is neither present. (Kamimura, M.)

Assembly-level analysis of heterogeneous Th–Pu PWR fuel

International Nuclear Information System (INIS)

Zainuddin, Nurjuanis Zara; Parks, Geoffrey T.; Shwageraus, Eugene

2017-01-01

Highlights: • We directly compare homogeneous and heterogeneous Th–Pu fuel. • Examine whether there is an increase in Pu incineration in the latter. • Homogeneous fuel was able to achieve much higher Pu incineration. • In the heterogeneous case, U-233 breeding is faster (larger power fraction), thus decreasing incineration of Pu. - Abstract: This study compares homogeneous and heterogeneous thorium–plutonium (Th–Pu) fuel assemblies (with high Pu content – 20 wt%), and examines whether there is an increase in Pu incineration in the latter. A seed-blanket configuration based on the Radkowsky thorium reactor concept is used for the heterogeneous assembly. This separates the thorium blanket from the uranium seed, or in this case a plutonium seed. The seed supplies neutrons to the subcritical thorium blanket which encourages the in situ breeding and burning of "2"3"3U, allowing the fuel to stay critical for longer, extending burnup of the fuel. While past work on Th–Pu seed-blanket units shows superior Pu incineration compared to conventional U–Pu mixed oxide fuel, there is no literature to date that directly compares the performance of homogeneous and heterogeneous Th–Pu assembly configurations. Use of exactly the same fuel loading for both configurations allows the effects of spatial separation to be fully understood. It was found that the homogeneous fuel with and without burnable poisons was able to achieve much higher Pu incinerations than the heterogeneous fuel configurations, while still attaining a reasonably high discharge burnup. This is because in the heterogeneous cases, "2"3"3U breeding is faster, thereby contributing to a much larger fraction of total power produced by the assembly. In contrast, "2"3"3U build-up is slower in the homogeneous case and therefore Pu burning is greater. This "2"3"3U begins to contribute a significant fraction of power produced only towards the end of life, thus extending criticality, allowing more Pu to

A preliminary evaluation of the ability of from-reactor casks to geometrically accommodate commercial LWR spent nuclear fuel

International Nuclear Information System (INIS)

Andress, D.; McLeod, N.B.; Rahimi, M.; Joy, D.S.; Peterson, R.W.

1991-01-01

The DOE has sponsored a number of cask design efforts to define several transportation casks to accommodate the various assemblies expected to be accepted by the Federal Waste Management System. At this time, three preliminary cask designs have been selected for the final design - the GA-4 and GA-9 truck casks and the BR-100 rail cask. The GA-4 cask is designed for PWR fuel only; the GA-9 cask is a longer cask with less shielding designed for BWR fuel only; and the BR-100 cask is designed to accommodate both PWR and BWR fuels. In total, this assessment indicates that the current Initiative I cask designs can be expected to dimensionally accommodate 100% of the PWR fuel assemblies (other than the extra-long South Texas Fuel) with control elements removed, and >90% of the assemblies having the control elements as an integral part of the fuel assembly. For BWR assemblies, >99% of the assemblies can be accommodated with fuel channels removed. Because of the button and spring interference, the basket openings in these casks will not accommodate assemblies in the BWR/2,3 and BWR/4-6 fuel classes with the fuel channels in place

Management of radioactive waste nuclear power plants

International Nuclear Information System (INIS)

Dlouhy, Z.; Marek, J.

1976-01-01

The authors give a survey of the sources, types and amounts of radioactive waste in LWR nuclear power stations (1,300 MWe). The amount of solid waste produced by a Novovorenezh-type PWR reactor (2 x 400 resp. 1 x 1,000 MWe) is given in a table. Treatment, solidification and final storage of radioactive waste are shortly discussed with special reference to the problems of final storage in the CSR. (HR) [de

Radioactive waste. Policy and perspective

Energy Technology Data Exchange (ETDEWEB)

Roberts, L E.J. [UKAEA, Harwell. Atomic Energy Research Establishment

1979-01-01

The subject is covered in sections as follows: general introduction (volume of waste arising from 1 GW/(e) energy per year); characteristics of highly active waste (output of some important fission products from an AGR, decay of activity with time for PWR and CFR wastes, toxic potential versus time for magnox and fast reactor wastes, toxic potential of unreprocessed magnox fuel); general principles of waste disposal (incorporation of waste into solid matrices, glass containers); design of stores and repositories (heat dissipation, siting and design, packing materials, size of repositories); the geologic barrier (location of repositories, safety analysis of repositories); the option of ocean disposal; status of work and present programme (vitrification, repository siting and design); conclusions.

Predisposal of Radioactive Waste from NPP 1000 MWe

International Nuclear Information System (INIS)

Suryantoro

2007-01-01

Predisposal of radioactive waste from NPP 1000 MW which was planned to be operated in 2016 has been conducted. In this study NPP applying PWR type was assumed. This assessment comprises all aspects of radioactive waste coming from NPP. One through cycle was chosen consequently no reprocessing step will be conducted. The assessment shows that technologically all radioactive waste treatment process rising from NPP operation has similarities to the existing radioactive waste process conducted by RWI which has lower scale of waste amount. (author)

Flexibility of ADS for minor actinides transmutation in different two-stage PWR-ADS fuel cycle scenarios

International Nuclear Information System (INIS)

Zhou, Shengcheng; Wu, Hongchun; Zheng, Youqi

2018-01-01

Highlights: •ADS reloading scheme is optimized to raise discharge burnup and lower reactivity loss. •ADS is flexible to be combined with various pyro-chemical reprocessing technologies. •ADS is flexible to transmute MAs from different spent PWR fuels. -- Abstract: A two-stage Pressurized Water Reactor (PWR)-Accelerator Driven System (ADS) fuel cycle is proposed as an option to transmute minor actinides (MAs) recovered from the spent PWR fuels in the ADS system. At the second stage, the spent fuels discharged from ADS are reprocessed by the pyro-chemical process and the recovered actinides are mixed with the top-up MAs recovered from the spent PWR fuels to fabricate the new fuels used in ADS. In order to lower the amount of nuclear wastes sent to the geological repository, an optimized scattered reloading scheme for ADS is proposed to maximize the discharge burnup and lower the burnup reactivity loss. Then the flexibility of ADS for MA transmutation is evaluated in this research. Three aspects are discussed, including: different cooling time of spent ADS fuels before reprocessing, different reprocessing loss of spent ADS fuels, and different top-up MAs recovered from different kinds of spent PWR fuels. The ADS system is flexible to be combined with various pyro-chemical reprocessing technologies with specific spent fuels cooling time and unique reprocessing loss. The reduction magnitudes of the long-term decay heat and radiotoxicity of MAs by transmutation depend on the reprocessing loss. The ADS system is flexible to transmute MAs recovered from different kinds of spent PWR fuels, regardless of UOX or MOX fuels. The reduction magnitudes of the long-term decay heat and radiotoxicity of different MAs by transmutation stay on the same order.

Neutron transport study based on assembly modular ray tracing MOC method

International Nuclear Information System (INIS)

Tian Chao; Zheng Youqi; Li Yunzhao; Li Shuo; Chai Xiaoming

2015-01-01

It is difficulty for the MOC method based on Cell Modular Ray Tracing to deal with the irregular geometry such as the water gap between the PWR lattices. Hence, the neutron transport code NECP-Medlar based on Assembly Modular Ray Tracing is developed. CMFD method is used to accelerate the transport calculation. The numerical results of the 2D C5G7 benchmark and typical PWR lattice prove that NECP-Medlar has an excellent performance in terms of accuracy and efficiency. Besides, NECP-Medlar can describe clearly the flux distribution of the lattice with water gap. (authors)

PWR secondary water chemistry guidelines: Revision 3

International Nuclear Information System (INIS)

Lurie, S.; Bucci, G.; Johnson, L.; King, M.; Lamanna, L.; Morgan, E.; Bates, J.; Burns, R.; Eaker, R.; Ward, G.; Linnenbom, V.; Millet, P.; Paine, J.P.; Wood, C.J.; Gatten, T.; Meatheany, D.; Seager, J.; Thompson, R.; Brobst, G.; Connor, W.; Lewis, G.; Shirmer, R.; Gillen, J.; Kerns, M.; Jones, V.; Lappegaard, S.; Sawochka, S.; Smith, F.; Spires, D.; Pagan, S.; Gardner, J.; Polidoroff, T.; Lambert, S.; Dahl, B.; Hundley, F.; Miller, B.; Andersson, P.; Briden, D.; Fellers, B.; Harvey, S.; Polchow, J.; Rootham, M.; Fredrichs, T.; Flint, W.

1993-05-01

An effective, state-of-the art secondary water chemistry control program is essential to maximize the availability and operating life of major PWR components. Furthermore, the costs related to maintaining secondary water chemistry will likely be less than the repair or replacement of steam generators or large turbine rotors, with resulting outages taken into account. The revised PWR secondary water chemistry guidelines in this report represent the latest field and laboratory data on steam generator corrosion phenomena. This document supersedes Interim PWR Secondary Water Chemistry Recommendations for IGA/SCC Control (EPRI report TR-101230) as well as PWR Secondary Water Chemistry Guidelines--Revision 2 (NP-6239)

A comprehensive in-pile test of PWR fuel bundle

Energy Technology Data Exchange (ETDEWEB)

Kang Rixin; Zhang Shucheng; Chen Dianshan (Academia Sinica, Beijing (China). Inst. of Atomic Energy)

1991-02-01

An in-pile test of PWR fuel bundle has been conducted in HWRR at IAE of China. This paper describes the structure of the test bundle (3x3-2), fabrication process and quality control of the fuel rod, irradiation conditions and the main Post Irradiation Examination (PIE) results. The test fuel bundle was irradiated under the PWR operation and water chemistry conditions with an average linear power of 381 W/cm and reached an average burnup of 25010 MWd/tU of the fuel bundle. After the test, destructive and non-destructive examination of the fuel rods was conducted at hot laboratories. The fission gas release was 10.4-23%. The ridge height of cladding was 3 to 8 {mu}m. The hydrogen content of the cladding was 80 to 140 ppm. The fuel stack height was increased by 2.9 to 3.3 mm. The relative irradiation growth was about 0.11 to 0.17% of the fuel rod length. During the irradiation test, no fuel rod failure or other abnormal phenomena had been found by the on-line fuel failure monitoring system of the test loop and water sampling analysis. The structure of the test fuel assembly was left undamaged without twist and detectable deformation. (orig.).

The determination of critical nuclides in PWR waste streams

International Nuclear Information System (INIS)

Centner, B.

1993-01-01

A current method for the determination of critical nuclides in the waste streams produced by a nuclear power reactor consists in applying correlation factors or scaling factors between those critical nuclides and so called key radionuclides, which can be easily measured and are representatives for the occurrence of activation products (Co-60) and fission products (Cs-137) in the waste streams. BELGATOM (BA) has developed a code (low level waste Activity Assessment-LLWAA code). The use of the code can clarify the analytical technique lower detection level that has to be achieved for each critical nuclide, in order to accurately measure it's activity in the different types of waste. (1 tab., 1 fig.)

Computer simulation of variform fuel assemblies using Dragon code

International Nuclear Information System (INIS)

Ju Haitao; Wu Hongchun; Yao Dong

2005-01-01

The DRAGON is a cell code that developed for the CANDU reactor by the Ecole Polytechnique de Montreal of CANADA. Although, the DRAGON is mainly used to simulate the CANDU super-cell fuel assembly, it has an ability to simulate other geometries of the fuel assembly. However, only NEACRP benchmark problem of the BWR lattice cell was analyzed until now except for the CANDU reactor. We also need to develop the code to simulate the variform fuel assemblies, especially, for design of the advanced reactor. We validated that the cell code DRAGON is useful for simulating various kinds of the fuel assembly by analyzing the rod-shape fuel assembly of the PWR and the MTR plate-shape fuel assembly. Some other kinds of geometry of geometry were computed. Computational results show that the DRAGON is able to analyze variform fuel assembly problems and the precision is high. (authors)

Analysis of the performance of fuel cells PWR with a single enrichment and radial distribution of enrichments

International Nuclear Information System (INIS)

Vargas, S.; Gonzalez, J. A.; Alonso, G.; Del Valle, E.; Xolocostli M, J. V.

2008-01-01

One of the main challenges in the design of fuel assemblies is the efficient use of uranium achieving burnt homogeneous of the fuel rods as well as the burnt maximum possible of the same ones to the unload. In the case of the assemblies type PWR has been decided actually for fuel assemblies with a single radial enrichment. The present work has like effect to show the because of this decision, reason why a comparison of the neutronic performance of two fuel cells takes place with the same enrichment average but one of them with radial distribution of enrichment and the other with a single enrichment equal to the average. The results shown in the present study of the behavior of the neutron flow as well as the power distribution through of assembly sustain the because of a single radial enrichment. (Author)

Implementation in free software of the PWR type university nucleo electric simulator (SU-PWR)

International Nuclear Information System (INIS)

Valle H, J.; Hidago H, F.; Morales S, J.B.

2007-01-01

Presently work is shown like was carried out the implementation of the University Simulator of Nucleo-electric type PWR (SU-PWR). The implementation of the simulator was carried out in a free software simulation platform, as it is Scilab, what offers big advantages that go from the free use and without cost of the product, until the codes modification so much of the system like of the program with the purpose of to improve it or to adapt it to future routines and/or more advanced graphic interfaces. The SU-PWR shows the general behavior of a PWR nuclear plant (Pressurized Water Reactor) describing the dynamics of the plant from the generation process of thermal energy in the nuclear fuel, going by the process of energy transport toward the coolant of the primary circuit the one which in turn transfers this energy to the vapor generators of the secondary circuit where the vapor is expanded by means of turbines that in turn move the electric generator producing in this way the electricity. The pressurizer that is indispensable for the process is also modeled. Each one of these stages were implemented in scicos that is the Scilab tool specialized in the simulation. The simulation was carried out by means of modules that contain the differential equation that mathematically models each stage or equipment of the PWR plant. The result is a series of modules that based on certain entrances and characteristic of the system they generate exits that in turn are the entrance to other module. Because the SU-PWR is an experimental project in early phase, it is even work and modifications to carry out, for what the models that are presented in this work can vary a little the being integrated to the whole system to simulate, but however they already show clearly the operation and the conformation of the plant. (Author)

Management of wastes from dismantled nuclear power plants

International Nuclear Information System (INIS)

1979-01-01

The problems associated with the management of radioactive wastes encountered in the dismantling of a 1200MWe PWR reactor are considered. It is possible to extend all the conclusions reached in these studies to BWR's or other reactors of the same type using light water as a coolant and moderator. The studies performed established the specific characteristics of these wastes: a gamma activity due essentially to 60 Co (after some fifty years this radioisotope will have decayed sufficiently to enable it to be stored without shielding); the presence of 63 Ni and 59 Ni (these long half-life beta emitting radioisotopes need to be stored over a long or even indefinite period of time); contaminated components (60% of the overall wastes), the reselling of these components involving costly decontamination processes. Extensive studies have been conducted on the management and handling of these wastes: packaging, transport, processing, storage and a great many techniques have been developed. However, further developments in concentration methods (fusion, crushing, cryogenics etc) and the selection of storage sites for this type of waste are necessary. Depending on the solutions chosen, the global cost of the wastes coming from a 1200 MW PWR reactor can vary between 10 and 20 million BFR

Fuel rod D07/B15 from Ringhals 2 PWR: Source material for corrosion/leach tests in groundwater. Fuel rod/pellet characterization program. Pt. 1

International Nuclear Information System (INIS)

Forsyth, R.

1987-03-01

A joint SKB/STUDSVIK experimental program to determine the corrosion rates and to establish the corrosion mechanisms of spent UO 2 fuel in groundwater under both oxidizing and reducing conditions is in progress in the Hot Cell Laboratory of Studsvik Energiteknik AB. High burnup fuel of both BWR and PWR type are studied. Characterization of the spent fuel at both rod and pellet level is an important part of the experimental program. Experiments on PWR fuel have been concentrated so far on specimens from one rod, manufacturer's number 03688, which had occupied position B15 in assembly D07. This assembly had been irradiated for 5 cycles in the Ringhals 2 reactor between 1977 and 1983. The calculated assembly burnup was 41.3 MWd/kg U. The present report is a collection of separate reports describing those items in the characterization program which have been performed so far. No overall summary of the experimental results is given here, and the report should be viewed as a collection of reference data. (orig.)

STYCA, a computer program in the dynamic structural analysis of a PWR core

International Nuclear Information System (INIS)

Silva Macedo, L.V. da; Breyne Salvagni, R. de

1992-01-01

A procedure for the dynamic structural analysis of a PWR core is presented, impacts between fuel assemblies may occur because of the existence of gaps between them. Thus, the problem is non-linear and an spectral analysis is avoided. A time-history response analysis is necessary. The Modal Superposition Method with the Duhamel integral was used in order to solve the problem. An algorithm of solution and also results obtained with the STYCA computer program, developed on the basis of what was proposed here, are presented. (author)

Reactor control system. PWR

International Nuclear Information System (INIS)

2009-01-01

At present, 23 units of PWR type reactors have been operated in Japan since the start of Mihama Unit 1 operation in 1970 and various improvements have been made to upgrade operability of power stations as well as reliability and safety of power plants. As the share of nuclear power increases, further improvements of operating performance such as load following capability will be requested for power stations with more reliable and safer operation. This article outlined the reactor control system of PWR type reactors and described the control performance of power plants realized with those systems. The PWR control system is characterized that the turbine power is automatic or manually controlled with request of the electric power system and then the nuclear power is followingly controlled with the change of core reactivity. The system mainly consists of reactor automatic control system (control rod control system), pressurizer pressure control system, pressurizer water level control system, steam generator water level control system and turbine bypass control system. (T. Tanaka)

PWR control rod ejection analysis with the numerical nuclear reactor

International Nuclear Information System (INIS)

Hursin, M.; Kochunas, B.; Downar, T. J.

2008-01-01

During the past several years, a comprehensive high fidelity reactor LWR core modeling capability has been developed and is referred to as the Numerical Nuclear Reactor (NNR). The NNR achieves high fidelity by integrating whole core neutron transport solution and ultra fine mesh computational fluid dynamics/heat transfer solution. The work described in this paper is a preliminary demonstration of the ability of NNR to provide a detailed intra pin power distribution during a control rod ejection accident. The motivation of the work is to quantify the impact on the fuel performance calculation of a more physically accurate representation of the power distribution within the fuel rod during the transient. The paper addresses first, the validation of the transient capability of the neutronic module of the NNR code system, DeCART. For this purpose, a 'mini core' problem consisting of a 3x3 array of typical PWR fuel assemblies is considered. The initial state of the 'mini core' is hot zero power with a control rod partially inserted into the central assembly which is fresh fuel and is adjacent to once and twice burned fuel representative of a realistic PWR arrangement. The thermal hydraulic feedbacks are provided by a simplified fluids and heat conduction solver consistent for both PARCS and DeCART. The control rod is ejected from the central assembly and the transient calculation is performed with DeCART and compared with the results of the U.S. NRC core simulation code PARCS. Because the pin power reconstruction in PARCS is based on steady state intra assembly pin power distributions which do not account for thermal feedback during the transient and which do not take into account neutron leakage from neighboring assemblies during the transient, there are some small differences in the PARCS and DeCART pin power prediction. Intra pin power density information obtained with DeCART represents new information not available with previous generation of methods. The paper then

Metallurgical and mechanical parameters controlling alloy 718 stress corrosion cracking resistance in PWR primary water

International Nuclear Information System (INIS)

Deleume, J.

2007-11-01

Improving the performance and reliability of the fuel assemblies of the pressurized water reactors requires having a perfect knowledge of the operating margins of both the components and the materials. The choice of alloy 718 as reference material for this study is justified by the industrial will to identify the first order parameters controlling the excellent resistance of this alloy to Stress Corrosion Cracking (SCC). For this purpose, a specific slow strain rate (SSR) crack initiation test using tensile specimen with a V-shaped hump in the middle of the gauge length was developed and modeled. The selectivity of such SSR tests in simulated PWR primary water at 350 C was clearly established by characterizing the SCC resistance of nine alloy 718 thin strip heats. Regardless of their origin and in spite of a similar thermo-mechanical history, they did not exhibit the same susceptibility to SCC crack initiation. All the characterized alloy 718 heats develop oxide scale of similar nature for various exposure times to PWR primary medium in the temperature range [320 C - 360 C]. δ phase precipitation has no impact on alloy 718 SCC initiation behavior when exposed to PWR primary water, contrary to interstitial contents and the triggering of plastic instabilities (PLC phenomenon). (author)

Calculation of source term in spent PWR fuel assemblies for dry storage and shipping cask design

International Nuclear Information System (INIS)

Fernandez, J. L.; Lopez, J.

1986-01-01

Using the ORIGEN-2 Coda, the decay heat and neutron and photon sources for an irradiated PWR fuel element have been calculated. Also, parametric studies on the behaviour of the magnitudes with the burn-up, linear heat power and irradiation and cooling times were performed. Finally, a comparison between our results and other design calculations shows a good agreement and confirms the validity of the used method. (Author) 6 refs

Verification of FA2D Prediction Capability Using Fuel Assembly Benchmark

International Nuclear Information System (INIS)

Jecmenica, R.; Pevec, D.; Grgic, D.; Konjarek, D.

2008-01-01

FA2D is 2D transport collision probability code developed at Faculty of Electrical Engineering and Computing, University Zagreb. It is used for calculation of cross section data at fuel assembly level. Main objective of its development was capability to generate cross section data to be used for fuel management and safety analyses of PWR reactors. Till now formal verification of code predictions capability is not performed at fuel assembly level, but results of fuel management calculations obtained using FA2D generated cross sections for NPP Krsko and IRIS reactor are compared against Westinghouse calculations. Cross section data were used within NRC's PARCS code and satisfactory preliminary results were obtained. This paper presents results of calculations performed for Nuclear Fuel Industries, Ltd., benchmark using FA2D, and SCALE5 TRITON calculation sequence (based on discrete ordinates code NEWT). Nuclear Fuel Industries, Ltd., Japan, released LWR Next Generation Fuels Benchmark with the aim to verify prediction capability in nuclear design for extended burnup regions. We performed calculations for two different Benchmark problem geometries - UO 2 pin cell and UO 2 PWR fuel assembly. The results obtained with two mentioned 2D spectral codes are presented for burnup dependency of infinite multiplication factor, isotopic concentration of important materials and for local peaking factor vs. burnup (in case of fuel assembly calculation).(author)

PWR-GALE, Radioactive Gaseous Release and Liquid Release from PWR

International Nuclear Information System (INIS)

Chandrasekaran, T.; Lee, J.Y.; Willis, C.A.

1988-01-01

1 - Description of program or function: The PWR-GALE (Boiling Water Reactor Gaseous and Liquid Effluents) Code is a computerized mathematical model for calculating the release of radioactive material in gaseous and liquid effluents from pressurized water reactors (PWRs). The calculations are based on data generated from operating reactors, field tests, laboratory tests, and plant-specific design considerations incorporated to reduce the quantity of radioactive materials that may be released to the environment. 2 - Method of solution: GALE calculates expected releases based on 1) standardized coolant activities derived from ANS Standards 18.1 Working Group recommendations, 2) release and transport mechanisms that result in the appearance of radioactive material in liquid and gaseous waste streams, 3) plant-specific design features used to reduce the quantities of radioactive materials ultimately released to the environs, and 4) information received on the operation of nuclear power plants. 3 - Restrictions on the complexity of the problem: The liquid release portion of GALE uses subroutines taken from the ORIGEN (CCC-217) to calculate radionuclide buildup and decay during collection, processing, and storage of liquid radwaste. Memory requirements for this part of the program are determined by the large nuclear data base accessed by these subroutines

ZZ PWR-AXBUPRO-GKN, Measured Axial Burnup Profiles, NPP Neckarewstheim

International Nuclear Information System (INIS)

Neuber, Jens-Christian; Lamprecht, Thomas

1999-01-01

Description or function: PWR-AXBUPRO-GKN12 contains Axial Burnup Shapes released by Siemens AG Power Generation Group. It contains data sets relative to following NPP and initial enrichment: - NPP Neckarwestheim 1, Fuel assemblies with an initial enrichment of 3.5 wt.-% 235-U; - NPP Neckarwestheim 2, Fuel assemblies with an initial enrichment of 3.5 wt.-% 235-U; - NPP Neckarwestheim 2, Fuel assemblies with an initial enrichment of 3.8 wt.-% 235-U; - NPP Neckarwestheim 2, Fuel assemblies with an initial enrichment of 4.0 wt.-% 235-U. In each of these files the axial shapes are listed one after the other. Each shape is characterised by: - the number of the cycle; - the number of the fuel assembly. - axial burnup shape characteristics: - height (in centimeter) of the nodes with respect to the active length of the fuel assemblies normalized to the cold, unirradiated state. - the nodal burnup (in MWd/kg U). - fuel assembly design data as well as core geometry and operating data pertinent to depletion calculations: NPP Neckarwestheim 1 (GKN1) - (square pitch lattice 15X15 - thermal Power 2497 MW)thermal Power 2497 MW); More than 700 EOC axial shapes from cycle 18 up. From cycle 18 to cycle 20 a change from an Out-In-Loading to an In-Out-Loading has taken place. Fuel assemblies up to number 1093 have spacer grids made of Inconel, whereas all the fuel assemblies from number 1094 up have spacer grids made of Zircaloy. Discharge burnups range from: 9.7 to 52.8 MWd/kg. NPP Neckarwestheim 2 (GKN2) - (square pitch lattice 18X18 - thermal Power 3850 MW) more than 500 EOC axial shapes from cycle 5 up: - More than 170 shapes for an initial fuel enrichment of 3.5 wt.-% 235-U, discharge burnup ranges from 16.3 to 44.4 MWd/kg; - more than 170 shapes for an initial fuel enrichment of 3.8 wt.-% 235-U, discharge burnup ranges from 14.0 to 52.8 MWd/kg; - more than 180 shapes for an initial fuel enrichment of 4.0 wt.-% 235-U. discharge burnup ranges from 15.5 to 48.9 MWd/kg. PWR AXBUPRO

A universal PWR spectral history correction

International Nuclear Information System (INIS)

Hutt, P.K.; Nunn, D.L.

1989-01-01

The accuracy of a form of universal correction for the difference between depletion conditions assumed in PWR assembly lattice calculations and those experienced in a reactor burn-up is investigated. The correction is based on lattice calculations in which only one such depletion history difference, depletion at two different water densities, is explicitly represented by lattice calculations. The assumption is made that other historical effects bear the same relationship to an appropriate time-average of the two-group neutron flux spectrum. The correction is shown to be accurate for the most important historical effects, depletion with burnable absorbers inserted, control rods inserted or at a different soluble boron level, in addition to density itself. The correction is less accurate for representing depletion at a different fuel or coolant temperature but even in these cases gives an improvement over no correction. In addition it is argued that these historic temperature effects are likely to be of minor importance. (author)

Probabilistic analysis on the failure of reactivity control for the PWR

Science.gov (United States)

Sony Tjahyani, D. T.; Deswandri; Sunaryo, G. R.

2018-02-01

The fundamental safety function of the power reactor is to control reactivity, to remove heat from the reactor, and to confine radioactive material. The safety analysis is used to ensure that each parameter is fulfilled during the design and is done by deterministic and probabilistic method. The analysis of reactivity control is important to be done because it will affect the other of fundamental safety functions. The purpose of this research is to determine the failure probability of the reactivity control and its failure contribution on a PWR design. The analysis is carried out by determining intermediate events, which cause the failure of reactivity control. Furthermore, the basic event is determined by deductive method using the fault tree analysis. The AP1000 is used as the object of research. The probability data of component failure or human error, which is used in the analysis, is collected from IAEA, Westinghouse, NRC and other published documents. The results show that there are six intermediate events, which can cause the failure of the reactivity control. These intermediate events are uncontrolled rod bank withdrawal at low power or full power, malfunction of boron dilution, misalignment of control rod withdrawal, malfunction of improper position of fuel assembly and ejection of control rod. The failure probability of reactivity control is 1.49E-03 per year. The causes of failures which are affected by human factor are boron dilution, misalignment of control rod withdrawal and malfunction of improper position for fuel assembly. Based on the assessment, it is concluded that the failure probability of reactivity control on the PWR is still within the IAEA criteria.

Activity transport models for PWR primary circuits; PWR-ydinvoimalaitoksen primaeaeripiirin aktiivisuuskulkeutumismallit

Energy Technology Data Exchange (ETDEWEB)

Tanner, V; Rosenberg, R [VTT Chemical Technology, Otaniemi (Finland)

1995-03-01

The corrosion products activated in the primary circuit form a major source of occupational radiation dose in the PWR reactors. Transport of corrosion activity is a complex process including chemistry, reactor physics, thermodynamics and hydrodynamics. All the mechanisms involved are not known and there is no comprehensive theory for the process, so experimental test loops and plant data are very important in research efforts. Several activity transport modelling attempts have been made to improve the water chemistry control and to minimise corrosion in PWR`s. In this research report some of these models are reviewed with special emphasis on models designed for Soviet VVER type reactors. (51 refs., 16 figs., 4 tabs.).

Impact of thermal constraints on the optimal design of high-level waste repositories in geologic media

Energy Technology Data Exchange (ETDEWEB)

Malbrain, C; Lester, R K [Massachusetts Inst. of Tech., Cambridge (USA). Dept. of Nuclear Engineering

1982-12-01

An approximate, semi-analytical heat conduction model for predicting the time-dependent temperature distribution in the region of a high-level waste repository has been developed. The model provides the basis for a systematic, inexpensive examination of the impact of several independent thermal design constraints on key repository design parameters and for determining the optimal set of design parameters which satisfy these constraints. Illustrative calculations have been carried out for conceptual repository designs for spent pressurized water reactor (PWR) fuel and reprocessed PWR high-level waste in salt and granite media.

Development of DGR System Concept for Radioactive Waste from Pyro-processing of CANDU SNFs

International Nuclear Information System (INIS)

Kim, In Young; Choi, Heui Joo; Lee, Jong Youl; Lee, Minsoo; Kim, Hyeon A

2016-01-01

In this study, DGR concept for radioactive waste from pyro-processing of CANDU SNFs is developed. Identical material balance for PWR (MB 2.6.0) and mass ratio of radioactive nuclides to binding material for LiCl-KCl waste is applied to determine specification of waste form, packing/disposal canister. Optimum thermal dimensioning is estimated to be 40 m for disposal tunnel and 8 m for disposal hole pitch through ABAQUS thermal analyses. To reduce volume and toxicity of PWR SNFs, the P and T technology using pyro-processing and SFR is under development in KAERI. CANDU SNFs are not considered as a subject of P and T because of its low fissile content caused by use of natural uranium as a fuel material. However, contention that not only PWR SNFs but also CANDU SNFs must be re-used is raised constantly. To evaluate impact of application of P and T on CANDU SNFs in the perspective of disposal, DGR system concept for radioactive waste from pyroprocessing of CANDU SNFs based on material balance version 2.6.0 is developed in this study. The disposal area is expected to be about 20,800 m 2 for disposal of 842,000 CANDU fuel bundles.

Development of DGR System Concept for Radioactive Waste from Pyro-processing of CANDU SNFs

Energy Technology Data Exchange (ETDEWEB)

Kim, In Young; Choi, Heui Joo; Lee, Jong Youl; Lee, Minsoo; Kim, Hyeon A [KAERI, Daejeon (Korea, Republic of)

2016-05-15

In this study, DGR concept for radioactive waste from pyro-processing of CANDU SNFs is developed. Identical material balance for PWR (MB 2.6.0) and mass ratio of radioactive nuclides to binding material for LiCl-KCl waste is applied to determine specification of waste form, packing/disposal canister. Optimum thermal dimensioning is estimated to be 40 m for disposal tunnel and 8 m for disposal hole pitch through ABAQUS thermal analyses. To reduce volume and toxicity of PWR SNFs, the P and T technology using pyro-processing and SFR is under development in KAERI. CANDU SNFs are not considered as a subject of P and T because of its low fissile content caused by use of natural uranium as a fuel material. However, contention that not only PWR SNFs but also CANDU SNFs must be re-used is raised constantly. To evaluate impact of application of P and T on CANDU SNFs in the perspective of disposal, DGR system concept for radioactive waste from pyroprocessing of CANDU SNFs based on material balance version 2.6.0 is developed in this study. The disposal area is expected to be about 20,800 m{sup 2} for disposal of 842,000 CANDU fuel bundles.

Thermal-hydraulic study of integrated steam generator in PWR

International Nuclear Information System (INIS)

Osakabe, Masahiro

1989-01-01

One of the safety aspects of innovative reactor concepts is the integration of steam generators (SGs) into the reactor vessel in the case of the pressurized water reactor (PWR). All of the reactor system components including the pressurizer are within the reactor vessel in the SG integrated PWR. The simple heat transfer code was developed for the parametric study of the integrated SG. The code was compared to the once-through 19-tube SG experiment and the good agreement between the experimental results and the code predictions was obtained. The assessed code was used for the parametric study of the integrated once-through 16 m-straight-tube SG installed in the annular downcomer. The proposed integrated SG as a first attempt has approximately the same tube size and pitch as the present PWR and the SG primary and secondary sides in the present PWR is inverted in the integrated PWR. Based on the study, the reactor vessel size of the SG integrated PWR was calculated. (author)

Secondary water chemistry control practices and results of the Japanese PWR plants

International Nuclear Information System (INIS)

Maeda, Akihiro; Shoda, Yasuhiko; Ishihara, Nobuo; Murata, Kazutoyo; Fujiwara, Hiroyuki; Hayakawa, Hitoshi; Matsuda, Tadashi

2012-09-01

In Japan, since the start of the operation of the first PWR plant, Mihama Unit-1 in 1970, 24 PWR plants have been built by 2010, and all of them are in operation. Due to the plant-specific needs of management, and by flexibly incorporating the state-of-the-art insights into the design, the system configurations of the plants vary so many as 15 types. Meanwhile, the geographical feature of Japan makes all the Japanese PWR plants to have condensers cooled by sea water, and all the plants have a common system with a full-flow Condensate Polisher System (CPS). To prevent corrosion, continued improvements of the secondary water chemistry management has been performed like other countries, and one of the major features of the Japanese PWR plants is an enhanced provision for the condenser leakage. The water quality of SG (Steam Generator) has been significantly improved by the provision for the sea water leakage, in combination with other improvements in water chemistry management. Also in Japan, almost all of the treatments of the spent polisher resin and the wastewater are performed within the power plant sites. To facilitate the treatment of the waste water and the regeneration of the spent resins, either ammonia or ETA (Ethanol Amine) is selected as the pH adjustment agent for the secondary system water. Also at the ammonia treatment, high pH accomplishes the inhibition of the piping wall thinning and the lower iron transportation into SGs. In addition, the iron transported into the SG is removed by the chemical conditioning treatment called ASCA (Advanced Scale Conditioning Agent). This provides the effective recovery of the SG heat-transfer performance, and the improved SG support plate BEC (Broached Egg Crate) hole blockage rates. Basically in Japan, the secondary water chemistry management has been improved based on a single basic specification, for the variety of the plant configurations, with the plant-specific investigations and analyses. This paper summarizes

Analysis of accidental loss of pool coolant due to leakage in a PWR SFP

International Nuclear Information System (INIS)

Wu, Xiaoli; Li, Wei; Zhang, Yapei; Tian, Wenxi; Su, Guanghui; Qiu, Suizheng

2015-01-01

Highlights: • Accidental loss of pool coolant due to leakage in a PWR SFP was studied using MAAP5. • The effect of emergency ventilation on the accident progression was investigated. • The effect of emergency injection on the accident progression was discussed. - Abstract: A large loss of pool coolant/water accident may be caused by extreme accidents such as the pool wall or bottom floor punctures due to a large aircraft strike. The safety of SFP under this circumstance is very important. Large amounts of radioactive materials would be easily released into the environment if a severe accident happened in the SFP, because the spent fuel pool (SFP) in a PWR nuclear power station (NPS) is often located in the fuel handing building outside the reactor containment. To gain insight into the loss of pool coolant accident progression for a pressurized water reactor (PWR) SFP, a computational model was established by using the Modular Accident Analysis Program (MAAP5). Important factors such as Zr oxidation by air, air natural circulation and thermal radiation were considered for partial and complete drainage accidents without mitigation measures. The calculation indicated that even if the residual water level was in the active fuel region, there was a chance to effectively remove the decay heat through axial heat conduction (if the pool cooling system failed) or steam cooling (if the pool cooling system was working). For sensitivity study, the effects of emergency ventilation and water injection on the accident progression were analyzed. The analysis showed that for the current configuration of high-density storage racks, it was difficult to cool the spent fuels by air natural circulation. Enlarging the space between the adjacent assemblies was a way of increasing air natural circulation flow rate and maintaining the coolability of SFP. Water injection to the bottom of the SFP helped to recover water inventory, quenching the high temperature assemblies to prevent

PWR fuel of high enrichment with erbia and enriched gadolinia

International Nuclear Information System (INIS)

Bejmer, Klaes-Håkan; Malm, Christian

2011-01-01

Today standard PWR fuel is licensed for operation up to 65-70 MWd/kgU, which in most cases corresponds to an enrichment of more than 5 w/o "2"3"5U. Due to criticality safety reason of storage and transportation, only fuel up to 5 w/o "2"3"5U enrichment is so far used. New fuel storage installations and transportation casks are necessary investments before the reactivity level of the fresh fuel can be significantly increased. These investments and corresponding licensing work takes time, and in the meantime a solution that requires burnable poisons in all pellets of the fresh high-enriched fuel might be used. By using very small amounts of burnable absorber in every pellet the initial reactivity can be reduced to today's levels. This study presents core calculations with fuel assemblies enriched to almost 6 w/o "2"3"5U mixed with a small amount of erbia. Some of the assemblies also contain gadolinia. The results are compared to a reference case containing assemblies with 4.95 w/o "2"3"5U without erbia, utilizing only gadolinia as burnable poison. The comparison shows that the number of fresh fuel assemblies can be reduced by 21% (which increases the batch burnup by 24%) by utilizing the erbia fuel concept. However, increased cost of uranium due to higher enrichment is not fully compensated for by the cost gain due to the reduction of the number assemblies. Hence, the fuel cycle cost becomes slightly higher for the high enrichment erbia case than for the reference case. (author)

Evaluation of burnup credit for accommodating PWR spent nuclear fuel in high-capacity cask designs

International Nuclear Information System (INIS)

Wagner, John C.

2003-01-01

This paper presents an evaluation of the amount of burnup credit needed for high-density casks to transport the current U.S. inventory of commercial spent nuclear fuel (SNF) assemblies. A prototypic 32-assembly cask and the current regulatory guidance were used as bases for this evaluation. By comparing actual pressurized-water-reactor (PWR) discharge data (i.e., fuel burnup and initial enrichment specifications for fuel assemblies discharged from U.S. PWRs) with actinide-only-based loading curves, this evaluation finds that additional negative reactivity (through either increased credit for fuel burnup or cask design/utilization modifications) is necessary to accommodate the majority of SNF assemblies in high-capacity storage and transportation casks. The impact of varying selected calculational assumptions is also investigated, and considerable improvement in effectiveness is shown with the inclusion of the principal fission products (FPs) and minor actinides and the use of a bounding best-estimate approach for isotopic validation. Given sufficient data for validation, the most significant component that would improve accuracy, and subsequently enhance the utilization of burnup credit, is the inclusion of FPs. (author)

PWR loading pattern optimization using Harmony Search algorithm

International Nuclear Information System (INIS)

Poursalehi, N.; Zolfaghari, A.; Minuchehr, A.

2013-01-01

Highlights: ► Numerical results reveal that the HS method is reliable. ► The great advantage of HS is significant gain in computational cost. ► On the average, the final band width of search fitness values is narrow. ► Our experiments show that the search approaches the optimal value fast. - Abstract: In this paper a core reloading technique using Harmony Search, HS, is presented in the context of finding an optimal configuration of fuel assemblies, FA, in pressurized water reactors. To implement and evaluate the proposed technique a Harmony Search along Nodal Expansion Code for 2-D geometry, HSNEC2D, is developed to obtain nearly optimal arrangement of fuel assemblies in PWR cores. This code consists of two sections including Harmony Search algorithm and Nodal Expansion modules using fourth degree flux expansion which solves two dimensional-multi group diffusion equations with one node per fuel assembly. Two optimization test problems are investigated to demonstrate the HS algorithm capability in converging to near optimal loading pattern in the fuel management field and other subjects. Results, convergence rate and reliability of the method are quite promising and show the HS algorithm performs very well and is comparable to other competitive algorithms such as Genetic Algorithm and Particle Swarm Intelligence. Furthermore, implementation of nodal expansion technique along HS causes considerable reduction of computational time to process and analysis optimization in the core fuel management problems

The Technology Trend of Japanese Patent for the Nuclear Fuel Assembly Inspection

International Nuclear Information System (INIS)

Cho, Jai Wan; Choi, Young Soo; Lee, Nam Ho; Jeong, Kyung Min; Suh, Yong Chil; Kim, Chang Hoi; Shin, Jung Cheol

2008-06-01

Japanese technology patents for the nuclear fuel assembly inspection unit, from the year 1993 to the year 2006, were investigated. The fuel rods which contain fissile material are grouped together in a closely-spaced array within the fuel assembly. Various kinds of reactor including the PWR reactor are being operated in Japan. There are many kinds of nuclear fuel assemblies in Japan, and the shape and the size of these nuclear fuel assemblies are various also. As the structure of these various fuel assemblies is a regular square as the same as the Korean one, the inspection method described in Japanese technology patent can be applied to the inspection of the nuclear fuel assembly of the Korea. This report focuses on advances in VIT(visual inspection test) of nuclear fuel assembly using the state-of-the-art CCD camera system

The Technology Trend of Japanese Patent for the Nuclear Fuel Assembly Inspection

Energy Technology Data Exchange (ETDEWEB)

Cho, Jai Wan; Choi, Young Soo; Lee, Nam Ho; Jeong, Kyung Min; Suh, Yong Chil; Kim, Chang Hoi; Shin, Jung Cheol

2008-06-15

Japanese technology patents for the nuclear fuel assembly inspection unit, from the year 1993 to the year 2006, were investigated. The fuel rods which contain fissile material are grouped together in a closely-spaced array within the fuel assembly. Various kinds of reactor including the PWR reactor are being operated in Japan. There are many kinds of nuclear fuel assemblies in Japan, and the shape and the size of these nuclear fuel assemblies are various also. As the structure of these various fuel assemblies is a regular square as the same as the Korean one, the inspection method described in Japanese technology patent can be applied to the inspection of the nuclear fuel assembly of the Korea. This report focuses on advances in VIT(visual inspection test) of nuclear fuel assembly using the state-of-the-art CCD camera system.

Observed TRU data from nuclear utility waste streams

International Nuclear Information System (INIS)

Wessman, R.A.; Floyd, J.G.; Leventhal, L.

1990-01-01

TMA/Norcal has performed 10CFR61 analysis of radioactive waste streams from BWR's and PWR's since 1983. Many standard and non-routine sample types have been received for analysis from nuclear power plants nation-wide. In addition to the 10CFR61 Tables I and II analyses, we also have analyzed for many of the supplementary isotopes. As part of this program TRU analyses are required. As a result, have accumulated a significant amount of data for plutonium, americium, and curium in radioactive waste for many different sample matrices from many different waste streams. This paper will present our analytical program for 10CFR61 TRU. The laboratory methodology including chemical and radiometric procedures is discussed. The sensitivity of our measurements and ability to meet the lower limits of detection is also discussed. Secondly, a review of TRU data is presented. Scaling factors and their ranges from selected PWR stations are included. We discuss some features of, and limits to, interpretation of these data. 8 refs., 3 tabs

Establishment of China Nuclear Fuel Assembly Database

International Nuclear Information System (INIS)

Chen Peng; Jin Yongli; Zhang Yingchao; Lu Huaquan; Chen Jianxin

2009-01-01

China Nuclear Fuel Assembly Database (CNFAD) is developed based on Oracle system. It contains the information of fuel assemblies in the stages of its design, fabrication and post irradiation (PIE). The structure of Browser Sever is adopted in the development of the software, which supports the HTTP protocol. It uses Java interface to transfer the codes from server to clients and make the sources of server and clients be utilized reasonably and sufficiently, so it can perform complicated tasks. Data in various stages of the fuel assemblies in Pressure Water Reactor (PWR), such as the design,fabrication, operation, and post irradiation examination, can be stored in this database. Data can be shared by multi users and communicated within long distances. By using CNFAD, the problem of decentralization of fuel data in China nuclear power plants will be solved. (authors)

Strength analysis of refueling machine for large PWR in nuclear power plant

International Nuclear Information System (INIS)

Jia Xiaofeng; Zhou Guofeng; Bi Xiangjun; Ji Shunying

2010-01-01

The refueling machine of PWR plays important roles in nuclear power plant operation,and the dynamic analysis and strength assessment should be carried out to check its safety. In this paper, the finite element model (FEM) was established with the software ANSYS 12 for the refueling machine structure of large 1 000 MW PWR. The dynamic computations were performed under three work conditions, i.e. normal (cart starting and braking), abnormal (OBE) and accident(SSE) conditions, respectively. The structure responses (internal force and stress) of refueling machine under earthquake response spectrum in three directions were combined with the method of square root of square sum (SRSS). Moreover, the static response under gravity was also considered to construct the most critical conditions. With the simulated results, the strength of main structure, bold and weld joint,and the stability of landing leg for additional crane were assessed based on the RCCM code. At last, the local stress analysis of finger-form hook, which function is to take fuel assemblies, was also analyzed, while its strength was also assessed. The results show that the strengths of the refueling machine under various working conditions can meet the safety requirements. (authors)

Experimental study of the tritium inventory in the BR3 and extrapolation to a P.W.R. of 900 MWe

International Nuclear Information System (INIS)

Charlier, A.; Gubel, P.; Vandenberg, C.; Haas, D.

1982-01-01

The aim of this report is to evaluate the tritium production and diffusion in uranium and plutonium fuel in the primary circuit of a PWR and to improve the knowledge about the production difference between the two kinds of isotopes. The first part of the work is relative to the experimental PWR BR3, cycle 4A, during which a constant control of the tritium activity has been performed in the primary circuit. These experimental evaluation was compared with the the theoretical estimation of the tritium production during the cycle 4A. From these observations and calculations, a tritium release fraction was deduced and estimated to be 0.81% of the total tritium produced in the fuel. The second part of the work is devoted to post-irradiation examinations on a few uranium and plutonium rods irradiated in the BR3 reactor. The tritium content was measured in the cladding, in the fuel and in the gas plenum for various samples of fuel rods. These results show the relationship between the release rate from the fuel matrix, the linear power and the burnup. The last part of the work is the estimate of the tritium production in a PWR of 900 MWe in operating conditions. The tritium production was calculated for an uranium fuelled core and for a core containing 30% of all plutonium fuel assemblies in a generic power plant of 900 MWe. From this study, it results that the loading with 30% plutonium assemblies at equilibrium increases the tritium balance in the moderator water of less than 5%

PWR secondary water chemistry study

International Nuclear Information System (INIS)

Pearl, W.L.; Sawochka, S.G.

1977-02-01

Several types of corrosion damage are currently chronic problems in PWR recirculating steam generators. One probable cause of damage is a local high concentration of an aggressive chemical even though only trace levels are present in feedwater. A wide variety of trace chemicals can find their way into feedwater, depending on the sources of condenser cooling water and the specific feedwater treatment. In February 1975, Nuclear Water and Waste Technology Corporation (NWT), was contracted to characterize secondary system water chemistry at five operating PWRs. Plants were selected to allow effects of cooling water chemistry and operating history on steam generator corrosion to be evaluated. Calvert Cliffs 1, Prairie Island 1 and 2, Surry 2, and Turkey Point 4 were monitored during the program. Results to date in the following areas are summarized: (1) plant chemistry variations during normal operation, transients, and shutdowns; (2) effects of condenser leakage on steam generator chemistry; (3) corrosion product transport during all phases of operation; (4) analytical prediction of chemistry in local areas from bulk water chemistry measurements; and (5) correlation of corrosion damage to chemistry variation

Rail-Cask Tests: Normal-Conditionsof- Transport Tests of Surrogate PWR Fuel Assemblies in an ENSA ENUN 32P Cask.

Energy Technology Data Exchange (ETDEWEB)

McConnell, Paul E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ross, Steven [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Grey, Carissa Ann [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Uncapher, William Leonard [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Arviso, Michael [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Garmendia, Rafael [Equipos Nucleares Sociedad Anonima, Madrid (Spain); Fernandez Perez, Ismael [Equipos Nucleares Sociedad Anonima, Madrid (Spain); Palacio, Alejandro [Equipos Nucleares Sociedad Anonima, Madrid (Spain); Calleja, Guillermo [Equipos Nucleares Sociedad Anonima, Madrid (Spain); Garrido, David [COORDINADORA, Madrid (Spain); Rodriguez Casas, Ana [COORDINADORA, Madrid (Spain); Gonzalez Garcia, Luis [COORDINADORA, Madrid (Spain); Chilton, Lyman Wes [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ammerman, Douglas J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Walz, Jacob [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gershon, Sabina [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Saltzstein, Sylvia J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sorenson, Ken [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Klymyshyn, Nicholas [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hanson, Brady [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pena, Ruben [Transportation Technology Center, Inc., Pueblo, CO (United States); Walker, Russell [Transportation Technology Center, Inc., Pueblo, CO (United States)

2018-01-01

This report describes tests conducted using a full-size rail cask, the ENSA ENUN 32P, involving handling of the cask and transport of the cask via truck, ships, and rail. The purpose of the tests was to measure strains and accelerations on surrogate pressurized water reactor fuel rods when the fuel assemblies were subjected to Normal Conditions of Transport within the rail cask. In addition, accelerations were measured on the transport platform, the cask cradle, the cask, and the basket within the cask holding the assemblies. These tests were an international collaboration that included Equipos Nucleares S.A., Sandia National Laboratories, Pacific Northwest National Laboratory, Coordinadora Internacional de Cargas S.A., the Transportation Technology Center, Inc., the Korea Radioactive Waste Agency, and the Korea Atomic Energy Research Institute. All test results in this report are PRELIMINARY – complete analyses of test data will be completed and reported in FY18. However, preliminarily: The strains were exceedingly low on the surrogate fuel rods during the rail-cask tests for all the transport and handling modes. The test results provide a compelling technical basis for the safe transport of spent fuel.

Comparative study of the contribution of various PWR spacer grid components to hydrodynamic and wall pressure characteristics

Energy Technology Data Exchange (ETDEWEB)

Bhattacharjee, Saptarshi, E-mail: saptarshi.bhattacharjee@outlook.com [Alternative Energies and Atomic Energy Commission (CEA) – Cadarache, DEN/DTN/STCP/LHC, 13108 Saint Paul lez Durance Cedex (France); Laboratoire de Mécanique, Modélisation et Procédés Propres (M2P2), UMR7340 CNRS, Aix-Marseille Université, Centrale Marseille, 13451 Marseille Cedex (France); Ricciardi, Guillaume [Alternative Energies and Atomic Energy Commission (CEA) – Cadarache, DEN/DTN/STCP/LHC, 13108 Saint Paul lez Durance Cedex (France); Viazzo, Stéphane [Laboratoire de Mécanique, Modélisation et Procédés Propres (M2P2), UMR7340 CNRS, Aix-Marseille Université, Centrale Marseille, 13451 Marseille Cedex (France)

2017-06-15

Highlights: • Complex geometry inside a PWR fuel assembly is simulated using simplified 3D models. • Structured meshes are generated as far as possible. • Fluctuating hydrodynamic and wall pressure field are analyzed using LES. • Comparative studies between square spacer grid, circular spacer grid and mixing vanes are presented. • Simulations are compared with experimental data. - Abstract: Flow-induced vibrations in a pressurized water reactor (PWR) core can cause fretting wear in fuel rods. These vibrations can compromise safety of a nuclear reactor. So, it is necessary to know the random fluctuating forces acting on the rods which cause these vibrations. In this paper, simplified 3D models like square spacer grid, circular spacer grid and symmetric mixing vanes have been used inside an annular pipe. Hydrodynamic and wall pressure characteristics are evaluated using large eddy simulations (LES). Structured meshes are generated as far as possible. Simulations are compared with an experiment. Results show that the grid and vanes have a combined effect: grid accelerates the flow whereas the vanes contribute to the swirl structures. Spectral analysis of the simulations illustrate vortex shedding phenomenon in the wake of spacer grids. This initial study opens up interesting perspectives towards improving the modeling strategy and understanding the complex phenomenon inside a PWR core.

Comparative study of the contribution of various PWR spacer grid components to hydrodynamic and wall pressure characteristics

International Nuclear Information System (INIS)

Bhattacharjee, Saptarshi; Ricciardi, Guillaume; Viazzo, Stéphane

2017-01-01

Highlights: • Complex geometry inside a PWR fuel assembly is simulated using simplified 3D models. • Structured meshes are generated as far as possible. • Fluctuating hydrodynamic and wall pressure field are analyzed using LES. • Comparative studies between square spacer grid, circular spacer grid and mixing vanes are presented. • Simulations are compared with experimental data. - Abstract: Flow-induced vibrations in a pressurized water reactor (PWR) core can cause fretting wear in fuel rods. These vibrations can compromise safety of a nuclear reactor. So, it is necessary to know the random fluctuating forces acting on the rods which cause these vibrations. In this paper, simplified 3D models like square spacer grid, circular spacer grid and symmetric mixing vanes have been used inside an annular pipe. Hydrodynamic and wall pressure characteristics are evaluated using large eddy simulations (LES). Structured meshes are generated as far as possible. Simulations are compared with an experiment. Results show that the grid and vanes have a combined effect: grid accelerates the flow whereas the vanes contribute to the swirl structures. Spectral analysis of the simulations illustrate vortex shedding phenomenon in the wake of spacer grids. This initial study opens up interesting perspectives towards improving the modeling strategy and understanding the complex phenomenon inside a PWR core.

A Study on Structural Strength of Irradiated Spacer Grid for PWR Fuel

Energy Technology Data Exchange (ETDEWEB)

Jin, Y. G.; Baek, S. J.; Kim, D. S.; Yoo, B. O.; Ahn, S. B.; Chun, Y. B. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, J. I.; Kim, Y. H.; Lee, J. J. [KEPCO NF, Daejeon (Korea, Republic of)

2014-10-15

A fuel assembly consists of an array of fuel rods, spacer grids, guide thimbles, instrumentation tubes, and top and bottom nozzles. In PWR (Pressurized light Water Reactor) fuel assemblies, the spacer grids support the fuel rods by the friction forces between the fuel rods and springs/dimples. Under irradiation, the spacer grids supporting the fuel rods absorb vibration impacts due to the reactor coolant flow, and also bear static and dynamic loads during operation inside the nuclear reactor and transportation for spent fuel storage. Thus, it is important to understand the characteristics of deformation behavior and the change in structural strength of an irradiated spacer grid.. In the present study, the static compression test of a spacer grid was conducted to investigate the structural strength of the irradiated spacer grid in a hot cell at IMEF (Irradiated Materials Examination Facility) of KAERI. To evaluate the structural strength of an irradiated spacer grid, hot cell tests were carried out at IMEF of KAERI. The fuel assembly was dismantled and the irradiated spacer grid was obtained for the compression test. The apparatus for measuring the compression strength of the irradiated spacer grid was developed and installed successfully in the hot cell.

Development of a thermal-hydraulic code for reflood analysis in a PWR experimental loop

International Nuclear Information System (INIS)

Alves, Sabrina P.; Mesquita, Amir Z.; Rezende, Hugo C.; Palma, Daniel A.P.

2017-01-01

A process of fundamental importance in the event of Loss of Coolant Accident (LOCA) in Pressurized Water nuclear Reactors (PWR) is the reflood of the core or rewetting of nuclear fuels. The Nuclear Technology Development Center (CDTN) has been developing since the 70’s programs to allow Brazil to become independent in the field of reactor safety analysis. To that end, in the 80’s was designed, assembled and commissioned one Rewetting Test Facility (ITR in Portuguese). This facility aims to investigate the phenomena involved in the thermal hydraulic reflood phase of a Loss of Coolant Accident in a PWR nuclear reactor. This work aim is the analysis of physical and mathematical models governing the rewetting phenomenon, and the development a thermo-hydraulic simulation code of a representative experimental circuit of the PWR reactors core cooling channels. It was possible to elaborate and develop a code called REWET. The results obtained with REWET were compared with the experimental results of the ITR, and with the results of the Hydroflut code, that was the old program previously used. An analysis was made of the evolution of the wall temperature of the test section as well as the evolution of the front for two typical tests using the two codes calculation, and experimental results. The result simulated by REWET code for the rewetting time also came closer to the experimental results more than those calculated by Hydroflut code. (author)

Development of a thermal-hydraulic code for reflood analysis in a PWR experimental loop

Energy Technology Data Exchange (ETDEWEB)

Alves, Sabrina P.; Mesquita, Amir Z.; Rezende, Hugo C., E-mail: sabrinapral@gmail.com, E-mail: amir@cdtn.brm, E-mail: hcr@cdtn.br, E-mail: hcr@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Palma, Daniel A.P., E-mail: dapalma@cnen.gov.br [Comissão Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil)

2017-07-01

A process of fundamental importance in the event of Loss of Coolant Accident (LOCA) in Pressurized Water nuclear Reactors (PWR) is the reflood of the core or rewetting of nuclear fuels. The Nuclear Technology Development Center (CDTN) has been developing since the 70’s programs to allow Brazil to become independent in the field of reactor safety analysis. To that end, in the 80’s was designed, assembled and commissioned one Rewetting Test Facility (ITR in Portuguese). This facility aims to investigate the phenomena involved in the thermal hydraulic reflood phase of a Loss of Coolant Accident in a PWR nuclear reactor. This work aim is the analysis of physical and mathematical models governing the rewetting phenomenon, and the development a thermo-hydraulic simulation code of a representative experimental circuit of the PWR reactors core cooling channels. It was possible to elaborate and develop a code called REWET. The results obtained with REWET were compared with the experimental results of the ITR, and with the results of the Hydroflut code, that was the old program previously used. An analysis was made of the evolution of the wall temperature of the test section as well as the evolution of the front for two typical tests using the two codes calculation, and experimental results. The result simulated by REWET code for the rewetting time also came closer to the experimental results more than those calculated by Hydroflut code. (author)

Optimization of the decontamination in EDF PWR power plants

International Nuclear Information System (INIS)

Gosset, P.; Dupin, M.; Buisine, D.; Buet, J.F.; Brunel, V.

2002-01-01

The optimisation of decontamination in EDF PWR power plants is the result of a permanent collaborative work between the plant operators, the subcontractors, central services of nuclear power division of EDF. This collaborative work enables the saving of all the feedback experience. The main operations carried out on nuclear sites like mechanical decontamination of valves, use of the ''EMMAC'' process on big components (replacement of steam generator, hydraulic parts of the reactor coolant pumps), use of foam on pools walls and divers in highly contaminated pools have been discussed. This paper shows that the choice of decontamination processes is very dependant on the components, on the dose rate reduction to be aimed and on the possibility to treat the waste on site. (authors)

Molten metal technologies advance waste processing systems for liquid radioactive waste treatment for PWRs and BWRs

International Nuclear Information System (INIS)

Strand, Gary; Vance, Jene N.

1997-01-01

Molten Metal Technologies (MMT) has recently acquired a proprietary filtration process for specific use in radioactive liquid waste processing systems. The filtration system has been incorporated in to a PWR liquid radwaste system which is currently being designed for the ComEd Byron Nuclear Station. It has also been adopted as the prefiltration step up from of the two RO systems which were part of the VECTRA acquisition and which are currently installed in the ComEd Dresden and Lacily Nuclear Stations. The filtration process has been successfully pilot-tested at both Byron and Dresden and is currently being tested at LaSalle. The important features of the filtration process are the high removal efficiencies for particulates, including colloidal particles, and the low solid waste volume generation per gallon filtered which translates into very small annual solid waste volumes. This filtration process system has been coupled with the use of selective ion exchange media in the PWR processing system to reduce the solid waste volumes generated compared to the current processing methods and to reduce the curie quantities discharged to the environs. In the BWR processing system, this filtration method allows the coupling of an RO system to provide for recycling greater than 95% of the liquid radwaste back to the plant for reuse while significantly reducing the solid waste volumes and operating costs. This paper discusses the process system configurations for the MMT Advanced Waste Processing Systems for both PWRs and BWRs. In addition, the pilot test data and full-scale performance projections for the filtration system are discussed which demonstrate the important features of the filtration process

Conceptual study of advanced PWR core design

International Nuclear Information System (INIS)

Kim, Young Jin; Chang, Moon Hee; Kim, Keung Ku; Joo, Hyung Kuk; Kim, Young Il; Noh, Jae Man; Hwang, Dae Hyun; Kim, Taek Kyum; Yoo, Yon Jong.

1997-09-01

The purpose of this project is for developing and verifying the core design concepts with enhanced safety and economy, and associated methodologies for core analyses. From the study of the sate-of-art of foreign advanced reactor cores, we developed core concepts such as soluble boron free, high convertible and enhanced safety core loaded semi-tight lattice hexagonal fuel assemblies. To analyze this hexagonal core, we have developed and verified some neutronic and T/H analysis methodologies. HELIOS code was adopted as the assembly code and HEXFEM code was developed for hexagonal core analysis. Based on experimental data in hexagonal lattices and the COBRA-IV-I code, we developed a thermal-hydraulic analysis code for hexagonal lattices. Using the core analysis code systems developed in this project, we designed a 600 MWe core and studied the feasibility of the core concepts. Two additional scopes were performed in this project : study on the operational strategies of soluble boron free core and conceptual design of large scale passive core. By using the axial BP zoning concept and suitable design of control rods, this project showed that it was possible to design a soluble boron free core in 600 MWe PWR. The results of large scale core design showed that passive concepts and daily load follow operation could be practiced. (author). 15 refs., 52 tabs., 101 figs

Conceptual study of advanced PWR core design

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Jin; Chang, Moon Hee; Kim, Keung Ku; Joo, Hyung Kuk; Kim, Young Il; Noh, Jae Man; Hwang, Dae Hyun; Kim, Taek Kyum; Yoo, Yon Jong

1997-09-01

The purpose of this project is for developing and verifying the core design concepts with enhanced safety and economy, and associated methodologies for core analyses. From the study of the sate-of-art of foreign advanced reactor cores, we developed core concepts such as soluble boron free, high convertible and enhanced safety core loaded semi-tight lattice hexagonal fuel assemblies. To analyze this hexagonal core, we have developed and verified some neutronic and T/H analysis methodologies. HELIOS code was adopted as the assembly code and HEXFEM code was developed for hexagonal core analysis. Based on experimental data in hexagonal lattices and the COBRA-IV-I code, we developed a thermal-hydraulic analysis code for hexagonal lattices. Using the core analysis code systems developed in this project, we designed a 600 MWe core and studied the feasibility of the core concepts. Two additional scopes were performed in this project : study on the operational strategies of soluble boron free core and conceptual design of large scale passive core. By using the axial BP zoning concept and suitable design of control rods, this project showed that it was possible to design a soluble boron free core in 600 MWe PWR. The results of large scale core design showed that passive concepts and daily load follow operation could be practiced. (author). 15 refs., 52 tabs., 101 figs.

Technical Support to an Operating PWR vis-a-vis Safety Analysis

International Nuclear Information System (INIS)

Gul, Subhan; Khan, M.; Chughtai, M. Kamran

2011-01-01

Currently a PWR of 300 MWe capacity CHASNUPP-I is in operation since the year 2000. Technical support being provided includes in-core fuel management and corresponding safety analysis for the reshuffled core for the next cycle. Currently calculation and analysis were performed for Cycle 6 to achieve the safe and economical loading pattern. The technique used is designated as out in mode (modified). In this technique, most of the fresh fuel assemblies are not directly located at the periphery of the core, but near the boundary. This technique has the advantage that without using burnable absorber we can design a low leakage core with extended cycle and maximum batch averaged burnup. (author)

Description and performance characteristics for the neutron Coincidence Collar for the verification of reactor fuel assemblies

International Nuclear Information System (INIS)

Menlove, H.O.

1981-08-01

An active neutron interrogation method has been developed for the measurement of 235 U content in fresh fuel assemblies. The neutron Coincidence Collar uses neutron interrogation with an AmLi neutron source and coincidence counting the induced fission reaction neutrons from the 235 U. This manual describes the system components, operation, and performance characteristics. Applications of the Coincidence Collar to PWR and BWR types of reactor fuel assemblies are described

Burn-up Credit Criticality Safety Benchmark-Phase II-E. Impact of Isotopic Inventory Changes due to Control Rod Insertions on Reactivity and the End Effect in PWR UO2 Fuel Assemblies

International Nuclear Information System (INIS)

Neuber, Jens Christian; Tippl, Wolfgang; Hemptinne, Gwendoline de; Maes, Philippe; Ranta-aho, Anssu; Peneliau, Yannick; Jutier, Ludyvine; Tardy, Marcel; Reiche, Ingo; Kroeger, Helge; Nakata, Tetsuo; Armishaw, Malcom; Miller, Thomas M.

2015-01-01

The report describes the final results of the Phase II-E Burn-up Credit Criticality Benchmark conducted by the Expert Group on Burn-up Credit Criticality Safety. The objective of Phase II of the Burn-up Credit Criticality Safety programme is to study the impact of axial burn-up profiles of PWR UO 2 spent fuel assemblies on the reactivity of PWR UO 2 spent fuel assembly configurations. The objective of the Phase II-E benchmark was to study the impact of changes on the spent nuclear fuel isotopic composition due to control rod insertion during depletion on the reactivity and the end effect of spent fuel assemblies with realistic axial burn-up profiles for different control rod insertion depths ranging from 0 cm (no insertion) to full insertion (i.e. to the case that the fuel assemblies were exposed to control rod insertion over their full active length). For this purpose two axial burn-up profiles have been extracted from an AREVA-NP-GmbH-owned 17x17-(24+1) PWR UO 2 spent fuel assembly burn-up profile database. One profile has an average burn-up of 30 MWd/kg U, the other profile is related to an average burn-up of 50 MWd/kg U. Two profiles with different average burn-up values were selected because the shape of the burn-up profile is affected by the average burn-up and the end effect depends on the average burn-up of the fuel. The Phase II-E benchmark exercise complements the Phase II-C and Phase II-D benchmark exercises. In Phase II-D different irradiation histories were analysed using different control rod insertion histories during depletion as well as irradiation histories without control rod insertion. But in all the histories analysed a uniform distribution of the burn-up and hence a uniform distribution of the isotopic composition were assumed; and in all the histories including any usage of control rods full insertion of the control rods was assumed. In Phase II-C the impact of the asymmetry of axial burn-up profiles on the reactivity and the end effect of

Seismic qualification of PWR plant auxiliary feedwater systems

International Nuclear Information System (INIS)

Lu, S.C.; Tsai, N.C.

1983-08-01

The NRC Standard Review Plan specifies that the auxiliary feedwater (AFW) system of a pressurized water reactor (PWR) is a safeguard system that functions in the event of a Safe Shutdown Earthquake (SSE) to remove the decay heat via the steam generator. Only recently licensed PWR plants have an AFW system designed to the current Standard Review Plan specifications. The NRC devised the Multiplant Action Plan C-14 in order to make a survey of the seismic capability of the AFW systems of operating PWR plants. The purpose of this survey is to enable the NRC to make decisions regarding the need of requiring the licensees to upgrade the AFW systems to an SSE level of seismic capability. To implement the first phase of the C-14 plan, the NRC issued a Generic Letter (GL) 81-14 to all operating PWR licensees requesting information on the seismic capability of their AFW systems. This report summarizes Lawrence Livermore National Laboratory's efforts to assist the NRC in evaluating the status of seismic qualification of the AFW systems in 40 PWR plants, by reviewing the licensees' responses to GL 81-14

In-pile data analysis of the comparative WWER/PWR test IFA-503.1. Final report.

Energy Technology Data Exchange (ETDEWEB)

Volkov, B.; Devold, H.; Ryazantzev, E.; Yakovlev, V.

1999-04-15

The comparative WWER/PWR test in IFA-503.1 was commenced in July 1995 and successfully finished at the end of November 1998. The main objective of the test was generation of representative and comparative data of standard WWER-440 fuel fabricated at the 'MSZ' Electrostal (Russia) and PWR type fuel manufactured at IFE Kjeller (Norway). The test assembly comprised two clusters, each with 3 WWER rods and 3 PWR type rods. Eight rods with two types of fuel were instrumented with expansion thermometers, four rods were equipped with both fuel stack elongation detectors and pressure transducers. All sensors worked satisfactorily during the test. The average burnups achieved in the lower and upper clusters were around 25 and 20 MWd/kgUO{sub 2}, respectively. Some difference in densification of the two types of fuel was revealed during the first irradiation period. However, the fuel temperatures and commencement of fuel stack swelling were similar despite this fact. At the end of the test the rig was moved to a higher flux position in the HBWR core with the aim of promoting FGR and to compare the behaviour of the two types of fuel under higher power. Pressure measurements indicated a comparable low FGR (around 1 percent) in both types of rods. The centreline temperatures measured in the PWR rods were very close to the Halden FGR threshold whilst the WWER fuel temperatures were slightly lower. Despite the differences found in the behaviour of the two types of fuel during the test, the analysis of the in-pile data showed that these differences would not affect the fuel efficiency, at least, up to the burnup achieved in the test. It is supposed that these differences can be related to the fuel microstructure, in particular to the fuel grain and pore sizes (author) (ml)

In-pile data analysis of the comparative WWER/PWR test IFA-503.1. Final report

Energy Technology Data Exchange (ETDEWEB)

Volkov, B.; Devold, H.; Ryazantzev, E.; Yakovlev, V

1999-04-15

The comparative WWER/PWR test in IFA-503.1 was commenced in July 1995 and successfully finished at the end of November 1998. The main objective of the test was generation of representative and comparative data of standard WWER-440 fuel fabricated at the 'MSZ' Electrostal (Russia) and PWR type fuel manufactured at IFE Kjeller (Norway). The test assembly comprised two clusters, each with 3 WWER rods and 3 PWR type rods. Eight rods with two types of fuel were instrumented with expansion thermometers, four rods were equipped with both fuel stack elongation detectors and pressure transducers. All sensors worked satisfactorily during the test. The average burnups achieved in the lower and upper clusters were around 25 and 20 MWd/kgUO{sub 2}, respectively. Some difference in densification of the two types of fuel was revealed during the first irradiation period. However, the fuel temperatures and commencement of fuel stack swelling were similar despite this fact. At the end of the test the rig was moved to a higher flux position in the HBWR core with the aim of promoting FGR and to compare the behaviour of the two types of fuel under higher power. Pressure measurements indicated a comparable low FGR (around 1 percent) in both types of rods. The centreline temperatures measured in the PWR rods were very close to the Halden FGR threshold whilst the WWER fuel temperatures were slightly lower. Despite the differences found in the behaviour of the two types of fuel during the test, the analysis of the in-pile data showed that these differences would not affect the fuel efficiency, at least, up to the burnup achieved in the test. It is supposed that these differences can be related to the fuel microstructure, in particular to the fuel grain and pore sizes (author) (ml)

Characteristics of borosilicate waste glass form for high-level radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Kim, Seung Soo; Chun, Kwan Sik; Choi, Jong Won; Kang, Chul Hyung

2001-03-01

Basic data, required for the design and the performance assessment of a repository of HLW, suchas the chemical composition and the characteristics of the borosilicate waste glass have been identified according to the burn-ups of spent PWR fuels. The diemnsion of waste canister is 430mm in diameter and 1135mm in length, and the canister should hold less than 2kwatts of heat from their decay of radionuclides contained in the HLW. Based on the reprocessing of 5 years-cooled spent fuel, one canister could hold about 11.5wt.% and 10.8wt.% of oxidized HLW corresponding to their burn-ups of 45,000MWD/MTU and 55,000MWD/MTU, respectively. These waste forms have been recommanded as the reference waste forms of HLW. The characteristics of these wastes as a function of decay time been evaluated. However, after a specific waste form and a specific site for the disposal would be selected, the characteristics of the waste should be reevaluated under the consideration of solidification period, loaded waste, storage condition and duration, site circumstances for the repository system and its performance assessment.

Characterization of Factors affecting IASCC of PWR Core Internals

Energy Technology Data Exchange (ETDEWEB)

Kim, Sung Woo; Hwang, Seong Sik; Kim, Won Sam [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2008-09-15

A lot works have been performed on IASCC in BWR. Recent efforts have been devoted to investigate IASCC in PWR, but the mechanism in PWR is not fully understood yet as compared with that in BWR due to a lack of data from laboratories and fields. Therefore it is strongly needed to review and analyse recent researches of IASCC in both BWR and PWR for establishing a proactive management technology for IASCC of core internals in Korean PWRs. This work is aimed to review mainly recent technical reports on IASCC of stainless steels for core internals in PWR. For comparison, the works on IASCC in BWR were also reviewed and briefly introduced in this report.

Application of curium measurements for safeguarding at reprocessing plants. Study 1: High-level liquid waste and Study 2: Spent fuel assemblies and leached hulls

International Nuclear Information System (INIS)

Rinard, P.M.; Menlove, H.O.

1996-03-01

In large-scale reprocessing plants for spent fuel assemblies, the quantity of plutonium in the waste streams each year is large enough to be important for nuclear safeguards. The wastes are drums of leached hulls and cylinders of vitrified high-level liquid waste. The plutonium amounts in these wastes cannot be measured directly by a nondestructive assay (NDA) technique because the gamma rays emitted by plutonium are obscured by gamma rays from fission products, and the neutrons from spontaneous fissions are obscured by those from curium. The most practical NDA signal from the waste is the neutron emission from curium. A diversion of waste for its plutonium would also take a detectable amount of curium, so if the amount of curium in a waste stream is reduced, it can be inferred that there is also a reduced amount of plutonium. This report studies the feasibility of tracking the curium through a reprocessing plant with neutron measurements at key locations: spent fuel assemblies prior to shearing, the accountability tank after dissolution, drums of leached hulls after dissolution, and canisters of vitrified high-level waste after separation. Existing pertinent measurement techniques are reviewed, improvements are suggested, and new measurements are proposed. The authors integrate these curium measurements into a safeguards system

Radionuclide compositions of spent fuel and high level waste from commercial nuclear reactors

International Nuclear Information System (INIS)

Goodill, D.R.; Tymons, B.J.

1984-10-01

This report provides information on radionuclide compositions of spent fuel and high level waste produced during reprocessing. The reactor types considered are Magnox, AGR, PWR and CFR. The activities of the radionuclides are calculated using the FISPIN code. The results are presented in a form suitable for radioactive waste management calculations. (author)

Characterization of low and medium level radioactive waste forms

International Nuclear Information System (INIS)

Sambell, R.A.J.

1983-01-01

The work reported was carried out during the first year of the Commission of the European Community's programme on the characterization of low and medium level waste forms. Ten reference waste forms plus others of special national interest have been identified covering PWR, BWR, GCR and reprocessing wastes. The immobilising media include the three main matrices: cement, polymers and bitumen, and a glass. Characterization is viewed as one input to quality assurance of the waste form and covers: waste-matrix compatibility, radiation effects, leaching, microbiological attack, shrinkage and swelling, ageing processes and thermal effects. The aim is a balanced programme of comparative data, predictive modelling and an undserstanding of basic mechanisms

PWR and WWER fuel performance. A comparison of major characteristics

International Nuclear Information System (INIS)

Weidinger, H.

2006-01-01

PWR and WWER fuel technologies have the same basic performance targets: most effective use of the energy stored in the fuel and highest possible reliability. Both fuel technologies use basically the same strategies to reach these targets: 1) Optimized reload strategies; 2) Maximal use of structural material with low neutron cross sections; 3) Decrease the fuel failure frequency towards a 'zero failure' performance by understanding and eliminating the root causes of those defects. The key driving force of the technology of both, PWR and WWER fuel is high burn-up. Presently a range of 45 - 50 MWD/kgU have been reached commercially for PWR and WWER fuel. The main technical limitations to reach high burn-up are typically different for PWR and WWER fuel: for PWR fuel it is the corrosion and hydrogen uptake of the Zr-based materials; for WWER fuel it is the mechanical and dimensional stability of the FA (and the whole core). Corrosion and hydrogen uptake of Zr-materials is a 'non-problem' for WWER fuel. Other performance criteria that are important for high burn-up are the creep and growth behaviour of the Zr materials and the fission gas release in the fuel rod. There exists a good and broad data base to model and design both fuel types. FA and fuel rod vibration appears to be a generic problem for both fuel types but with more evidence for PWR fuel performance reliability. Grid-to-rod fretting is still a major issue in the fuel failure statistics of PWR fuel. Fuel rod cladding defects by debris fretting is no longer a key problem for PWR fuel, while it still appears to be a significant root cause for WWER fuel failures. 'Zero defect' fuel performance is achievable with a high probability, as statistics for US PWR and WWER-1000 fuel has shown

Aqueous Corrosion Rates for Waste Package Materials

Energy Technology Data Exchange (ETDEWEB)

S. Arthur

2004-10-08

The purpose of this analysis, as directed by ''Technical Work Plan for: Regulatory Integration Modeling and Analysis of the Waste Form and Waste Package'' (BSC 2004 [DIRS 171583]), is to compile applicable corrosion data from the literature (journal articles, engineering documents, materials handbooks, or standards, and national laboratory reports), evaluate the quality of these data, and use these to perform statistical analyses and distributions for aqueous corrosion rates of waste package materials. The purpose of this report is not to describe the performance of engineered barriers for the TSPA-LA. Instead, the analysis provides simple statistics on aqueous corrosion rates of steels and alloys. These rates are limited by various aqueous parameters such as temperature (up to 100 C), water type (i.e., fresh versus saline), and pH. Corrosion data of materials at pH extremes (below 4 and above 9) are not included in this analysis, as materials commonly display different corrosion behaviors under these conditions. The exception is highly corrosion-resistant materials (Inconel Alloys) for which rate data from corrosion tests at a pH of approximately 3 were included. The waste package materials investigated are those from the long and short 5-DHLW waste packages, 2-MCO/2-DHLW waste package, and the 21-PWR commercial waste package. This analysis also contains rate data for some of the materials present inside the fuel canisters for the following fuel types: U-Mo (Fermi U-10%Mo), MOX (FFTF), Thorium Carbide and Th/U Carbide (Fort Saint Vrain [FSVR]), Th/U Oxide (Shippingport LWBR), U-metal (N Reactor), Intact U-Oxide (Shippingport PWR, Commercial), aluminum-based, and U-Zr-H (TRIGA). Analysis of corrosion rates for Alloy 22, spent nuclear fuel, defense high level waste (DHLW) glass, and Titanium Grade 7 can be found in other analysis or model reports.

Aqueous Corrosion Rates for Waste Package Materials

International Nuclear Information System (INIS)

Arthur, S.

2004-01-01

The purpose of this analysis, as directed by ''Technical Work Plan for: Regulatory Integration Modeling and Analysis of the Waste Form and Waste Package'' (BSC 2004 [DIRS 171583]), is to compile applicable corrosion data from the literature (journal articles, engineering documents, materials handbooks, or standards, and national laboratory reports), evaluate the quality of these data, and use these to perform statistical analyses and distributions for aqueous corrosion rates of waste package materials. The purpose of this report is not to describe the performance of engineered barriers for the TSPA-LA. Instead, the analysis provides simple statistics on aqueous corrosion rates of steels and alloys. These rates are limited by various aqueous parameters such as temperature (up to 100 C), water type (i.e., fresh versus saline), and pH. Corrosion data of materials at pH extremes (below 4 and above 9) are not included in this analysis, as materials commonly display different corrosion behaviors under these conditions. The exception is highly corrosion-resistant materials (Inconel Alloys) for which rate data from corrosion tests at a pH of approximately 3 were included. The waste package materials investigated are those from the long and short 5-DHLW waste packages, 2-MCO/2-DHLW waste package, and the 21-PWR commercial waste package. This analysis also contains rate data for some of the materials present inside the fuel canisters for the following fuel types: U-Mo (Fermi U-10%Mo), MOX (FFTF), Thorium Carbide and Th/U Carbide (Fort Saint Vrain [FSVR]), Th/U Oxide (Shippingport LWBR), U-metal (N Reactor), Intact U-Oxide (Shippingport PWR, Commercial), aluminum-based, and U-Zr-H (TRIGA). Analysis of corrosion rates for Alloy 22, spent nuclear fuel, defense high level waste (DHLW) glass, and Titanium Grade 7 can be found in other analysis or model reports

The role of cladding material for performance of LWR control assemblies

International Nuclear Information System (INIS)

Dewes, P.; Roppelt, A.

2000-01-01

The lifetime of control assemblies in LWRs can be limited presently by mechanical failure of the absorber cladding. The major cause of failure is mechanical interaction of the absorber with the cladding due to irradiation induced dimensional changes such as absorber swelling and cladding creep, resulting in cracking of the clad. Such failures occurred in both BWRs and PWRs. Experience and in-reactor tests revealed that cracking can be avoided principally by two ways: First, if strain rates and hence, stresses in the cladding are kept low (well below the yield strength), significant strains can be tolerated. This is the case for the cladding of PWR control assemblies with slowly swelling Ag-In-Cd absorber. Recent examinations of highly exposed PWR control assemblies confirmed the design correlation up to the presently used strain limit. Second, in such cases where strongly swelling absorber material like boron carbide is still preferred, materials which are resistant against irradiation assisted stress corrosion cracking (IASCC) can be used. The influence of material composition and condition on IASCC was studied in-reactor using tubular samples of various stainless steels and Ni-base alloys stressed by swelling mandrels. In several programme steps high purity materials with special features had been identified as resistant to IASCC. Another process of cladding damage which may occur in PWRs is wear caused by friction of the control rods in the surrounding guide structure. For replacement control assemblies this problem is solved by coating of the cladding. There exists meanwhile excellent experience of up to 18 operation cycles with coated claddings. (author)

Spent fuel disassembly hardware and other non-fuel bearing components: characterization, disposal cost estimates, and proposed repository acceptance requirements

Energy Technology Data Exchange (ETDEWEB)

Luksic, A.T.; McKee, R.W.; Daling, P.M.; Konzek, G.J.; Ludwick, J.D.; Purcell, W.L.

1986-10-01

There are two categories of waste considered in this report. The first is the spent fuel disassembly (SFD) hardware. This consists of the hardware remaining after the fuel pins have been removed from the fuel assembly. This includes end fittings, spacer grids, water rods (BWR) or guide tubes (PWR) as appropriate, and assorted springs, fasteners, etc. The second category is other non-fuel-bearing (NFB) components the DOE has agreed to accept for disposal, such as control rods, fuel channels, etc., under Appendix E of the standard utiltiy contract (10 CFR 961). It is estimated that there will be approximately 150 kg of SFD and NFB waste per average metric ton of uranium (MTU) of spent uranium. PWR fuel accounts for approximately two-thirds of the average spent-fuel mass but only 50 kg of the SFD and NFB waste, with most of that being spent fuel disassembly hardware. BWR fuel accounts for one-third of the average spent-fuel mass and the remaining 100 kg of the waste. The relatively large contribution of waste hardware in BWR fuel, will be non-fuel-bearing components, primarily consisting of the fuel channels. Chapters are devoted to a description of spent fuel disassembly hardware and non-fuel assembly components, characterization of activated components, disposal considerations (regulatory requirements, economic analysis, and projected annual waste quantities), and proposed acceptance requirements for spent fuel disassembly hardware and other non-fuel assembly components at a geologic repository. The economic analysis indicates that there is a large incentive for volume reduction.

Sizewell 'B' PWR reference design

International Nuclear Information System (INIS)

1982-04-01

The reference design for a PWR power station to be constructed as Sizewell 'B' is presented in 3 volumes containing 14 chapters and in a volume of drawings. The report describes the proposed design and provides the basis upon which the safety case and the Pre-Construction Safety Report have been prepared. The station is based on a 3425MWt Westinghouse PWR providing steam to two turbine generators each of 600 MW. The layout and many of the systems are based on the SNUPPS design for Callaway which has been chosen as the US reference plant for the project. (U.K.)

Balance and behavior of gaseous radionuclides released during initial PWR fuel reprocessing operations

International Nuclear Information System (INIS)

Leudet, A.; Miquel, P.; Goumondy, P.J.; Charrier, G.

1982-08-01

Five fuel pins, taken from a PWR fuel assembly with 32000 MWD/t burn-up were chopped and dissolved in leak-proof equipment designed for accurate determination of the composition and quantity of gaseous elements released in these operations. Analytical methods were specially developped to determine directly the noble gases, tritium and gaseous carbon compounds in the gas phase. Volatile iodine was kept as close as possible to the source by cold traps, then transferred to a caustic solution for quantitative analysis. The quantities and activities of gaseous fission products thus determined were compared with predicted values obtained through computation. Very good agreement was generally observed

Balance and behavior of gaseous radionuclides released during initial PWR fuel reprocessing operations

International Nuclear Information System (INIS)

Leudet, A.; Miquel, P.; Goumondy, P.J.; Charrier, G.

1983-01-01

Five fuel pins, taken from a PWR fuel assembly with 32,000 MwD/t burn-up were chopped and dissolved in leak-proof equipment designed for accurate determination of the composition and quantity of gaseous elements released in these operations. Analytical methods were specially developed to determine directly the noble gases, tritium and gaseous carbon compounds in the gas phase. Volatile iodine was kept as close as possible to the source by cold traps, then transferred to a caustic solution for quantitative analysis. The quantities and activities of gaseous fission products thus determined were compared with predicted values obtained through computation. Very good agreement was generally observed

Program of monitoring PWR fuel in Spain; Programa de Vigilancia de Combustible pwr en Espana

Energy Technology Data Exchange (ETDEWEB)

Martinez Murillo, J. C.; Quecedo, M.; Munoz-Roja, C.

2015-07-01

In the year 2000 the PWR utilities: Centrales Nucleares Almaraz-Trillo (CNAT) and Asociacion Nuclear Asco-Vandellos (ANAV), and ENUSA Industrias Avanzadas developed and executed a coordinated strategy named PIC (standing for Coordinated Research Program), for achieving the highest level of fuel reliability. The paper will present the scope and results of this program along the years and will summarize the way the changes are managed to ensure fuel integrity. The excellent performance of the ENUSA manufactured fuel in the PWR Spanish NPPs is the best indicator that the expectations on this program are being met. (Author)

Study on virtual simulation technology for operation and control of PWR

International Nuclear Information System (INIS)

Fang Baoguo; Zhang Dafa; Lin Yajun

2006-01-01

The way to build graphical models of PWR with MultiGen Creator is discussed, and the three-dimensional model used in the virtual simulation is built. The mathematical simulation model for PWR based on the platform of MFC and Vega is built through the analysis of the mathematical simulation of PWR. The way to perform the virtual effect is introduced associating with the Pressurizer. And, all above parts are connected in one with VC++ to perform the whole virtual simulation of PWR. (authors)

Expert System analysis of non-fuel assembly hardware and spent fuel disassembly hardware: Its generation and recommended disposal

International Nuclear Information System (INIS)

Williamson, D.A.

1991-01-01

Almost all of the effort being expended on radioactive waste disposal in the United States is being focused on the disposal of spent Nuclear Fuel, with little consideration for other areas that will have to be disposed of in the same facilities. one area of radioactive waste that has not been addressed adequately because it is considered a secondary part of the waste issue is the disposal of the various Non-Fuel Bearing Components of the reactor core. These hardware components fall somewhat arbitrarily into two categories: Non-Fuel Assembly (NFA) hardware and Spent Fuel Disassembly (SFD) hardware. This work provides a detailed examination of the generation and disposal of NFA hardware and SFD hardware by the nuclear utilities of the United States as it relates to the Civilian Radioactive Waste Management Program. All available sources of data on NFA and SFD hardware are analyzed with particular emphasis given to the Characteristics Data Base developed by Oak Ridge National Laboratory and the characterization work performed by Pacific Northwest Laboratories and Rochester Gas ampersand Electric. An Expert System developed as a portion of this work is used to assist in the prediction of quantities of NFA hardware and SFD hardware that will be generated by the United States' utilities. Finally, the hardware waste management practices of the United Kingdom, France, Germany, Sweden, and Japan are studied for possible application to the disposal of domestic hardware wastes. As a result of this work, a general classification scheme for NFA and SFD hardware was developed. Only NFA and SFD hardware constructed of zircaloy and experiencing a burnup of less than 70,000 MWD/MTIHM and PWR control rods constructed of stainless steel are considered Low-Level Waste. All other hardware is classified as Greater-ThanClass-C waste

Determination of burnup, cooling time and initial enrichment of PWR spent fuel by use of gamma-ray activity ratios

International Nuclear Information System (INIS)

Min, D.K.; Park, H.J.; Park, K.J.; Ro, S.G.; Park, H.S.

1999-01-01

The Korea Atomic Energy Institute has been developing the algorithms for sequential determination of cooling time, initial enrichment and burnup of the PWR spent fuel assembly by use of gamma ratio measurements, i.e. 134 Cs/ 137 Cs, 154 Eu/ 137 Cs and 106 Ru 137 Cs/( 134 Cs) 2 . Calculations were performed by applying the ORIGEN-S code. This method has advantages over combination techniques of neutron and gamma measurement, because of its simplicity and insensitivity to the measurement geometry. For verifying the algorithms an experiment for determining the cooling time, initial enrichment and burnup of the two PWR spent fuel rods was conducted by use of high-resolution gamma detector (HPGe) system only. This paper describes the method used and interim results of the experiment. This method can be applied for spent fuel characterization, burnup credit and safeguards of the spent fuel management facility

Scaling studies - PWR

International Nuclear Information System (INIS)

Sonneck, G.

1983-05-01

A RELAP 4/MOD 6 study was made based on the blowdown phase of the intermediate break experiment LOFT L5-1. The method was to set up a base model and to vary parametrically some areas where it is known or suspected that LOFT differs from a commercial PWR. The aim was not to simulate LOFT or a PWR exactly but to understand the influence of the following parameters on the thermohydraulic behaviour of the system and the clad temperature: stored heat in the downcomer (LOFT has rather large filler blocks in this part of the pressure vessel); bypass between downcomer and upper plenum; and core length. The results show that LOFT is prototypical for all calculated blowdowns. As the clad temperatures decrease with decreasing stored energy in the downcomer, increased bypass and increased core length, LOFT results seem to be realistic as long as realistic bypass sizes are considered; they are conservative in the two other areas. (author)

Water chemistry in PWR

International Nuclear Information System (INIS)

Abe, Kenji

1987-01-01

This article outlines major features and basic concept of the secondary system of PWR's and water properties control measures adopted in recent PWR plants. The secondary system of a PWR consists of a condenser cooling pipe (aluminum-brass, titanium, or stainless steel), low-pressure make-up water heating pipe (aluminum-brass or stainless steel), high-ressure make-up water heating pipe (cupro-nickel or stainless steel), steam generator heat-transfer pipe (Inconel 600 or 690), and bleed/drain pipe (carbon steel, low alloy steel or stainless steel). Other major pipes and equipment are made of carbon steel or stainless steel. Major troubles likely to be caused by water in the secondary system include reduction in wall thickness of the heat-transfer pipe, stress corrosion cracking in the heat-transfer pipe, and denting. All of these are caused by local corrosion due to concentration of purities contained in water. For controlling the water properties in the secondary system, it is necessary to prevent impurities from entering the system, to remove impurities and corrosion products from the system, and to prevent corrosion of apparatus making up the system. Measures widely adopted for controlling the formation of IGA include the addition of boric acid for decreasing the concentration of free alkali and high hydrazine operation for providing a highly reducing atmospere. (Nogami, K.)

Duo_2-Steel cermet manufacturing technology for PWR Spent Nuclear Fuel (SNF) casks

International Nuclear Information System (INIS)

Siti Alimah; Budiarto

2005-01-01

Assessment of DUO_2-Steel cermet manufacturing technology for PWR SNF casks has been done. DUO_2-Steel cermet consisting of DUO_2 particulates and other particulates, embedded in a steel matrix. Cermet SNF casks have the potential for superior performance compared with casks constructed of other materials. The addition of DUO_2 ceramic particulates can increase SNF cask capacity, improve of repository performance and disposal of excess depleted uranium as potential waste. Two sets of cermet manufacturing technologies are casting and powder metallurgy. Three casting methods are infusion casting, traditional casting and centrifugal casting. While for powder metallurgy methods there are traditional method and new method. DUO_2-Steel cermet have traditionally been produced by powder metallurgy methods. The production of a cask, however, presents special requirements: the manufacture of an annular object with weights up to 100 tons, and methods are being not to manufacture a cermet of this size and geometry. A new powder metallurgy method, is a method for manufacturing cermet for PWR SNF cask. This powder metallurgy techniques have potentials low costs and provides greater freedom In the design of the cermet cask by allowing variable cermet properties. (author)

Recent development for improving the PWR flexibility to load follow and frequency control operation

International Nuclear Information System (INIS)

Dubourg, M.

1983-01-01

The increasing production of nuclear electricity generated by PWR in the French network will modify the operating conditions of these plants for adjusting the electricity generation to the consumption. For assessing the adequacy of main components, FRAMATOME, in conjunction with Electricite de France and the Commissariat a l'Energie Atomique has undertaken a large R and D effort and initiated significant design changes for sustaining the new operating modes including. Daily load follow and frequency remote dispatch operation (+- 5% random fluctuation load around a present value). These new operating conditions generate additional mechanical and thermal sollicitations due to the frequent motion of control rod banks, consisting of: a) Mechanical fatigue cycling and wear at the level of control rod drive mechanisms (CRDM), control rods and guides tubes. b) Wear and thermal fatigue cycling at the level of fuel assemblies. This paper will present the various aspects of this program including: Identification of the most critical areas of components; Basic research in laboratories for resolving wear problems in PWR environment; Improvement of local hydraulics for reducing loads; Endurance testing of full scale components on testing facilities. (orig./GL)

ABB advanced BWR and PWR fuel

International Nuclear Information System (INIS)

Junkrans, S.; Helmersson, S.; Andersson, S.

1999-01-01

Fuel designed and fabricated by ABB is now operating in 40 PWRs and BWRs in Europe, the United States and Korea. An excellent fuel reliability track record has been established. High burnups are proven for both BWR and PWR. Thermal margin improving features and advanced burnable absorber concepts enable the utilities to adopt demanding duty cycles to meet new economic objectives. In particular we note the excellent reliability record of ABB PWR fuel equipped with Guardian TM debris filter, proven to meet the -6 rod-cycles fuel failure goal, and the out-standing operating record of the SVEA 10x10 BWR fuel, where ABB is the only vendor to date with multi batch experience to high burnup. ABB is dedicated to maintain high fuel reliability as well as continually improve and develop a broad line of BWR and PWR products. ABB's development and fuel follow-up activities are performed in close co-operation with its customers. (orig.)

Cementation of wastes with boric acid

International Nuclear Information System (INIS)

Tello, Cledola C.O.; Haucz, Maria Judite A.; Alves, Lilian J.L.; Oliveira, Arno H.

2000-01-01

In nuclear power plants (PWR) are generated wastes, such as concentrate, which comes from the evaporation of liquid radioactive wastes, and spent resins. Both have boron in their composition. The cementation process is one of the options to solidify these wastes, but the boron has a negative effect on the setting of the cement mixture. In this paper are presented the experiments that are being carried out in order to overcome this problem and also to improve the efficiency of the process. Simulated wastes were cemented using additives (clays, admixtures etc.). In the process and product is being evaluated the effect of the amount, type and addition order of the materials. The mixtures were selected in accordance with their workability and incorporated waste. The solidified products are monolithic without free water with a good mechanical resistance. (author)

Waste management in light-water reactors

International Nuclear Information System (INIS)

Meininger, S.

1982-01-01

The most important objectives of concentrate and solid waste treatment are reduction of the waste to the smallest volume, radioactive exposure of the personnel of the power plants and outside for operation, handling and transportation, protection against migration of the concentrated radioactive substances after final disposal and observance of shipping requirements, national laws and ministerial waste storage regulations. A variety of technologies is available for the realization of these objectives. Important parameters for the selection and design of concentrate and solid waste treatment processes are waste type, quantity, activity, means for immobilization and the achievable reduction factors. The most important technologies for the treatment of liquid concentrates, combustible and non-combustible solid waste are available for example: In-Drum-Drying, Borate-Solidification (PWR), Drum Drier, Residue Filter Drying, Bituminization, Solidification with cement, Incineration, Shredding, Compacting etc. and of course combinations of the various mentioned procedures which result in the best possible waste disposal for the entire power plant. (orig./RW)

Parallel GPU implementation of PWR reactor burnup

International Nuclear Information System (INIS)

Heimlich, A.; Silva, F.C.; Martinez, A.S.

2016-01-01

Highlights: • Three GPU algorithms used to evaluate the burn-up in a PWR reactor. • Exhibit speed improvement exceeding 200 times over the sequential. • The C++ container is expansible to accept new nuclides chains. - Abstract: This paper surveys three methods, implemented for multi-core CPU and graphic processor unit (GPU), to evaluate the fuel burn-up in a pressurized light water nuclear reactor (PWR) using the solutions of a large system of coupled ordinary differential equations. The reactor physics simulation of a PWR reactor spends a long execution time with burnup calculations, so performance improvement using GPU can imply in better core design and thus extended fuel life cycle. The results of this study exhibit speed improvement exceeding 200 times over the sequential solver, within 1% accuracy.

CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 8 AND 9 CRYSTAL RIVER UNIT 3

International Nuclear Information System (INIS)

Wilson, Michael L.

2001-01-01

The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 8 and 9 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies

Characteristics of several equilibrium fuel cycles of PWR

International Nuclear Information System (INIS)

Waris, Abdul; Sekimoto, Hiroshi

2001-01-01

This paper evaluated the influence of neutron spectrum on characteristics of several equilibrium fuel cycles of pressurized water reactor (PWR). In this study, five kinds of fuel cycles were investigated. Required uranium enrichment, required natural uranium amount, and toxicity of heavy metals (HMs) in spent fuel were presented for comparison. The results showed that the enrichment and the required amount of natural uranium decrease significantly with increasing number of confined heavy nuclides when uranium is discharged from the reactor. On the other hand, when uranium is totally confined, the enrichment becomes extremely high. The confinement of plutonium and minor actinides (MA) seems effective in reducing radio-toxicity of discharged wastes. By confining all heavy nuclides except uranium those three characteristics could be reduced considerably. For this fuel cycle the toxicity of HMs in spent fuel become nearly equal to or less than that of loaded uranium. (author)

Decontamination and disposal of radioactive wastes from nuclear facilities

International Nuclear Information System (INIS)

Dlouhy, Z.

1978-01-01

A survey and characteristics are given of the main sources of wastes from the operation of nuclear installations. The amounts are compared of liquid and gaseous wastes from PWR and BWR reactors. The main trends of radioactive waste processing in the world are described. In Czechoslovakia, two methods of waste fixation have been developed: vacuum cementation and bituminization. The demands are summed up on radioactive waste storage sites and it is stated that there are a number of suitable localities, namely abolished granite quarries with a very deep ground water level and a low-permeable overburden and exhausted quarries of kaolinitic clays, which meet all criteria and secure the safe disposal of wastes from Czechoslovak nuclear power plants up to the year 2020. (Z.M.)

Parametric studies of the effect of MOx environment and control rods for PWR-UOx burnup credit implementation

International Nuclear Information System (INIS)

Barreau, Anne; Roque, Benedicte; Marimbeau, Pierre; Venard, Christophe; Bioux, Philippe; Toubon, Herve

2003-01-01

The increase of PWR-UOX fuel initial enrichment and the extensive needs for spent fuel storage or cask capacities reinforce the interest in taking burnup credit into account in criticality calculations. However, this utilization of credit for fuel burnup requires the definition of a methodology that ensures the conservatism of calculations. In order to guarantee the conservatism of the spent fuel inventory calculation, a depletion calculation scheme for burnup credit is under development. This paper presents the studies on the main parameters which have an effect on nuclides concentration: the presence of control rods during depletion and the fuel assembly environment, particularly the presence of MOx fuels around the UO 2 assembly. Reactivity effects which are relevant to these parameters are then presented, and physics phenomena are identified. (author)

Naval Waste Package Design Report

International Nuclear Information System (INIS)

M.M. Lewis

2004-01-01

A design methodology for the waste packages and ancillary components, viz., the emplacement pallets and drip shields, has been developed to provide designs that satisfy the safety and operational requirements of the Yucca Mountain Project. This methodology is described in the ''Waste Package Design Methodology Report'' Mecham 2004 [DIRS 166168]. To demonstrate the practicability of this design methodology, four waste package design configurations have been selected to illustrate the application of the methodology. These four design configurations are the 21-pressurized water reactor (PWR) Absorber Plate waste package, the 44-boiling water reactor (BWR) waste package, the 5-defense high-level waste (DHLW)/United States (U.S.) Department of Energy (DOE) spent nuclear fuel (SNF) Co-disposal Short waste package, and the Naval Canistered SNF Long waste package. Also included in this demonstration is the emplacement pallet and continuous drip shield. The purpose of this report is to document how that design methodology has been applied to the waste package design configurations intended to accommodate naval canistered SNF. This demonstrates that the design methodology can be applied successfully to this waste package design configuration and support the License Application for construction of the repository

Flow induced vibrations in gas tube assembly of centrifuge

International Nuclear Information System (INIS)

Alam, M.; Atta, M.A.; Mirza, J.A.; Khan, A.Q.

1986-01-01

A centrifuge essentially consists of a rotor rotating at very high speed. Gas tube assembly, located at the center of the rotor, is used to introduce feed gas into the rotor and remove product and waste streams from it. The gas tube assembly is thus a static component, the product and waste scoops of which are lying in the high pressure region of a fluid rotating at very high speed. This can cause flow induced vibrations in the gas tube assembly. Such vibrations affect not only the mechanical stability of the gas tube assembly but may also reduce the separative power of the centrifuge. In a cascade, if some of the centrifuges have gas tube vibration, then cascade performance will be affected. A theoretical analysis of the effect of waste tube vibrations on product and waste flow rates and pressures in the centrifuge is presented. A simple stage consisting of two centrifuges, in which one has tube vibration, is considered for this purpose. The results are compared with experiment. It is shown that waste tube vibration generates oscillations in waste and product flow rates that are observable outside the centrifuge. (author)

ABB PWR fuel design for high burnup

International Nuclear Information System (INIS)

Nilsson, S.; Jourdain, P.; Limback, M.; Garde, A.M.

1998-01-01

Corrosion, hydriding and irradiation induced growth of a based materials are important factors for the high burnup performance of PWR fuel. ABB has developed a number of Zr based alloys to meet the need for fuel that enables operation to elevated burnups. The materials include composition and processing optimised Zircaloy 4 (OPTIN TM ) and Zircaloy 2 (Zircaloy 2P), as well as advanced Zr based alloys with chemical compositions outside the composition specified for Zircaloy. The advanced alloys are either used as Duplex or as single component claddings. The Duplex claddings have an inner component of Zircaloy and an outer layer of Zr with small additions of alloying elements. ABB has furthermore improved the dimensional stability of the fuel assembly by developing stiffer and more bow resistant guide tubes while debris related fuel failures have been eliminated from ABB fuel by introducing the Guardian TM grid. Intermediate flow mixers that improve the thermal hydraulic performance and the dimensional stability of the fuel has also been developed within ABB. (author)

Mechanical characteristic evaluation of the mid grid spring in PWR fuel assembly

International Nuclear Information System (INIS)

Eum, K. B.; Lee, S. H.; Jeon, S. Y.; Kweon, Y. B.; Jeon, K. R.

2001-01-01

The spring load-deflection characteristic tests were performed for Westinghouse type 17x17 and 14x14 fuel assembly mid grids to evaluate the mechanical characteristics of the springs. Six kinds of prototype mid grids manufactured by KNFC were tested and two kinds of test methods were used: block test and in-grid test. The test results showed that all tested mid grid springs satisfied the criteria required at the beginning of fuel assembly life. In addition, the variation of spring characteristics resulting from the difference in the mechanical properties of spring material and spring shapes was investigated. And the validity of the test methods was discussed

The effects of gamma radiation on polymer matrix waste forms

International Nuclear Information System (INIS)

Johnson, D.I.; Burnay, S.G.; Phillips, D.C.

1986-06-01

A study has been made of the volume and weight changes, mechanical properties, and radiolytic gas production of polymer matrix waste forms during γ irradiation in open containers. The work has been commissioned by the Department of the Environment as part of its radioactive waste management research programme. The materials included polyester, vinyl ester, epoxide and polystyrene resins containing ion exchangers; and polyester and epoxide resins containing a PWR evaporator concentrate. (author)

Highlights of the French program on PWR fuel

Energy Technology Data Exchange (ETDEWEB)

Pages, J P [CEA Centre d` Etudes de Cadarache, 13 - Saint-Paul-lez-Durance (France). Direction des Reacteurs Nucleaires

1997-12-01

The presentation reviews the French programme on PWR fuel including the overall results of the year 1996 for nuclear operation; fuel management and economy; French nuclear electricity generation sites; production of nuclear generated electricity; energy availability of the 900 and 1,300 Mw PWR units; average radioactive liquid releases excluding tritium per unit; plutonium recycling experience.

Pushing back the boundaries of PWR fuel performance

International Nuclear Information System (INIS)

Sofer, G.A.; Skogen, F.B.; Brown, C.A.; Fresk, Y.U.

1985-01-01

In today's fiercely competitive PWR reload market utilities are benefiting from a variety of design innovations which are helping to cut fuel cycle costs and to improve fuel performance. An advanced PWR fuel design from Exxon, for example, currently under evaluation at the Ginna plant in the United States, offers higher burn-up and greater power cycling. (author)

Study of anticipated transient without scram for PWR

International Nuclear Information System (INIS)

Pu Jilong.

1985-01-01

Anticipated Transient Without Scram (ATWS) of PWR, the one of the 'Unresolved Safety Issue' with NRC, has been investigated for many years. The latest analysis done by the author considers the PWR's inherent stability and long-term performence under the condition of ATWS combined with SBLOCA and studies the sensitivity of several assumptions, which shows positive results

CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 4 AND 5 OF CRYSTAL RIVER UNIT 3

International Nuclear Information System (INIS)

Wright, Kenneth D.

1997-01-01

The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 4 and 5 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies

Estimate of the Sources of Plutonium-Containing Wastes Generated from MOX Fuel Production in Russia

International Nuclear Information System (INIS)

Kudinov, K.G.; Tretyakov, A.A.; Sorokin, Y.P.; Bondin, V.V.; Manakova, L.F.; Jardine, L.J.

2001-01-01

In Russia, mixed oxide (MOX) fuel is produced in a pilot facility ''Paket'' at ''MAYAK'' Production Association. The Mining-Chemical Combine (MCC) has developed plans to design and build a dedicated industrial-scale plant to produce MOX fuel and fuel assemblies (FA) for VVER-1000 water reactors and the BN-600 fast-breeder reactor, which is pending an official Russian Federation (RF) site-selection decision. The design output of the plant is based on production capacity of 2.75 tons of weapons plutonium per year to produce the resulting fuel assemblies: 1.25 tons for the BN-600 reactor FAs and the remaining 1.5 tons for VVER-1000 FAs. It is likely the quantity of BN-600 FAs will be reduced in actual practice. The process of nuclear disarmament frees a significant amount of weapons plutonium for other uses, which, if unutilized, represents a constant general threat. In France, Great Britain, Belgium, Russia, and Japan, reactor-grade plutonium is used in MOX-fuel production. Making MOX-fuel for CANDU (Canada) and pressurized water reactors (PWR) (Europe) is under consideration Russia. If this latter production is added, as many as 5 tons of Pu per year might be processed into new FAs in Russia. Many years of work and experience are represented in the estimates of MOX fuel production wastes derived in this report. Prior engineering studies and sludge treatment investigations and comparisons have determined how best to treat Pu sludges and MOX fuel wastes. Based upon analyses of the production processes established by these efforts, we can estimate that there will be approximately 1200 kg of residual wastes subject to immobilization per MT of plutonium processed, of which approximately 6 to 7 kg is Pu in the residuals per MT of Pu processed. The wastes are various and complicated in composition. Because organic wastes constitute both the major portion of total waste and of the Pu to be immobilized, the recommended treatment of MOX-fuel production waste is incineration

Radial power distribution shaping within a PWR fuel assembly utilizing asymmetrically loaded gadolinia-bearing fuel pins

International Nuclear Information System (INIS)

Stone, I.Z.

1992-01-01

As in-core fuel management designs evolve to meet the demands of increasing energy output, more innovative methods are developed to maintain power peaking within acceptable thermal margin limits. In-core fuel management staff must utilize various loading pattern strategies such as cross-core movement of fuel assemblies, multibatch enrichment schemes, and burnable absorbers as the primary means of controlling the radial power distribution. The utilization of fresh asymmetrically loaded gadolinia-bearing assemblies as a fuel management tool provides an additional means of controlling the radial power distribution. At Siemens Nuclear Power Corporation (SNP), fresh fuel assemblies fabricated with asymmetrically loaded gadolinia-bearing fuel rods have been used successfully for several cycles of reactor operation. Asymmetric assemblies are neutronically modeled using the same tools and models that SNP uses to model symmetrically loaded gadolinia-bearing fuel assemblies. The CASMO-2E code is used to produce the homogenized macroscopic assembly cross sections for the nodal core simulator. Optimum fuel pin locations within the asymmetrical assembly are determined using the pin-by-pin PDQ7 assembly core model for each new assembly design. The optimum pin location is determined by the rod loading that minimizes the peak-to-average pin power

Method and Result of Experiment for Support of Technical Solutions in the Field of Perfection of a Nuclear Fuel Cycle for Future PWR Reactors

International Nuclear Information System (INIS)

Ostrovskiy, V.; Kudryavtsev, E.; Tutnov, I.

2011-01-01

The paper presents the basics of approach of planning and carrying out of experiments to validate safety PWR reactors of the future when accepting technical solutions concerning using of improved fuel rods in fuel assembly. Basic principles and criteria used for the validation of technical solutions and developments in improving of nuclear fuel cycle of PWR reactors of the future are presented from the point of safety of future operation of modified fuel rods. We explore the questions of safety operation of PWR reactors with fuel assemblies, containing fuel rods with different length of fuel. The paper discusses the ways of solving of important tasks of critical facility experiments conducting for verification of new technical solutions in the sphere of PWR nuclear fuel cycle improvement on the base of international standards ISO 2000:9000 and functional safety recommendations of IEC (International Electromechanical Commission). New Federal laws of Russian Federation define the main principle for demands to NPP and any supplier of nuclear techniques. The principle is 'quantity indicators of risk should not exceed comprehensible social size of the established indicators of safety for any moment of operation of NPP'. On the other hand the second principle should be applied to extraction of the greatest benefit from operation of the equipment, systems or the NPP as whole: 'The long operation and full commercial use of resource and service properties of the equipment, systems and the NPP as a whole'. Realization of this principle assumes development and introduction of new technical solutions for a validation of guarantees of safety of the future operation of NPP or it separate components. Solving the practical problems of a validation of safety use of fuel rods with the increased length of a fuel column in fuel assembly in nuclear reactors of the future, we should choose new strategies and programs of verification experiments on the base of the analysis of guarantees

Completion of the fabrication and assembly of the internal parts and pressure vessel of the LABGENE reactor

International Nuclear Information System (INIS)

Guimaraes, Leonam dos Santos

2005-01-01

The Navy's Technological Center in Sao Paulo (CTMSP) has successfully concluded in 2005 the final assembly of the internals of the Laboratory of Energy Generation's Reactor (LABGENE). This structure together with the fuel elements and the control rods drives mechanisms are part of a PWR type Nuclear Reactor. (author)

The development of radioactive waste treatment technology (III)

International Nuclear Information System (INIS)

Kim, Joon Hyung; Jung, Ki Jung; Lee, Kune Woo; Park, Hun Hwee

1991-03-01

Most PWR stations have experienced leakages of boric acid and oil into liquid radwaste systems. Typically, these wastes have been concentrated by an evaporator system. Based on operating plant experiences, boric acid and oil are the majority of the solid loading for disposal and tend to decrease the efficiency significantly. The objective of these studies is to develop pretreatment techniques for the recovery of boric acid and for the removal of oil from such wastes for improving the evaporator performance. To these objectives, lab. scale reverse osmosis (RO) membrane and filtration/coalescence processes are introduced, which can separate boric acid and oil into waste streams. (Author)

Validation of PWR core seismic models with shaking table tests on interacting scale 1 fuel assemblies

International Nuclear Information System (INIS)

Viallet, E.; Bolsee, G.; Ladouceur, B.; Goubin, T.; Rigaudeau, J.

2003-01-01

The fuel assembly mechanical strength must be justified with respect to the lateral loads under accident conditions, in particular seismic loads. This justification is performed by means of time-history analyses with dynamic models of an assembly row in the core, allowing for assembly deformations, impacts at grid locations and reactor coolant effects. Due to necessary simplifications, the models include 'equivalent' parameters adjusted with respect to dynamic characterisation tests of the fuel assemblies. Complementing such tests on isolated assemblies by an overall model validation with shaking table tests on interacting assemblies is obviously desirable. Seismic tests have been performed by French CEA (Commissariat a l'Energie Atomique) on a row of six full scale fuel assemblies, including two types of 17 x 17 12ft design. The row models are built according to the usual procedure, with preliminary characterisation tests performed on a single assembly. The test-calculation comparisons are made for two test configurations : in air and in water. The relatively large number of accelerograms (15, used for each configuration) is also favourable to significant comparisons. The results are presented for the impact forces at row ends, displacements at mid assembly, and also 'statistical' parameters. Despite a non-negligible scattering in the results obtained with different accelerograms, the calculations prove realistic, and the modelling process is validated with a good confidence level. This satisfactory validation allows to evaluate precisely the margins in the seismic design methodology of the fuel assemblies, and thus to confirm the safety of the plants in case of seismic event. (author)

Tabulation of Fundamental Assembly Heat and Radiation Source Files

International Nuclear Information System (INIS)

T. deBues; J.C. Ryman

2006-01-01

The purpose of this calculation is to tabulate a set of computer files for use as input to the WPLOAD thermal loading software. These files contain details regarding heat and radiation from pressurized water reactor (PWR) assemblies and boiling water reactor (BWR) assemblies. The scope of this calculation is limited to rearranging and reducing the existing file information into a more streamlined set of tables for use as input to WPLOAD. The electronic source term files used as input to this calculation were generated from the output files of the SAS2H/ORIGIN-S sequence of the SCALE Version 4.3 modular code system, as documented in References 2.1.1 and 2.1.2, and are included in Attachment II

Process and device for fabricating nuclear fuel assembly grids

International Nuclear Information System (INIS)

Thiebaut, B.; Duthoo, D.; Germanaz, J.J.; Angilbert, B.

1991-01-01

The method for fabricating PWR fuel assembly grids consists to place the grid of which the constituent parts are held firmly in place within a frame into a sealed chamber full of inert gas. This chamber can rotate about an axis. The welding on one face at a time is carried out with a laser beam orthogonal to the axis orientation of the device. The laser source is outside of the chamber and the beam penetrates via a transparent view port

Determination of radionuclide migration parameters through immobilised radioactive waste; Odredjivanje migracionih parametara radionuklida kroz imobilisani radioaktivni otpad

Energy Technology Data Exchange (ETDEWEB)

Plecas, I; Drljaca, J; Peric, A; Kostadinovic, A [Institut za Nuklearne Nauke Boris Kidric, Belgrade (Yugoslavia)

1988-07-01

In this paper are presented results obtained from leakage rate determination of specific radionuclides (Co-60, Cs-137, Mn-54, Sr-85) in PWR NPP waste. Measurements were carried out using original IBK-Vinca method. This method permits simulation of radionuclide leakage through multiple safety barriers in engineered tranches system for radioactive waste disposal. These results will be used for future Yugoslav radioactive waste storing center. (author)

CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 1, 2, AND 3 OF CRYSTAL RIVER UNIT 3

International Nuclear Information System (INIS)

Wright, Kenneth D.

1997-01-01

The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 1, 2, and 3 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies

Use of the APOLLO2 transport code for PWR assembly studies

International Nuclear Information System (INIS)

Belhaffaf, D.; Coste, M.; Lenain, R.; Mathonniere, G.; Sanchez, R.; Stankovski, Z.; Zmijarevic, I.

1992-01-01

This paper presents some validation and application aspects of the APOLLO2, user oriented, modular code for multigroup transport assembly calculation which is developed at the French Commissariat a l'Energies Atomique. The main points approached in this paper are: the two dimensional collision probability convergence, critical leakage calculation schemes, self-shielding spatial discretization, and the equivalence procedure

CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 4 AND 5 OF CRYSTAL RIVER UNIT 3

Energy Technology Data Exchange (ETDEWEB)

Kenneth D. Wright

1997-07-30

The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 4 and 5 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies.

Sizewell: proposed site for Britain's first PWR power station

International Nuclear Information System (INIS)

1980-10-01

The pamphlet covers the following points, very briefly: nuclear power - a success story; the Government's nuclear programme; why Sizewell; the PWR (with diagram); the PWR at Sizewell (with aerial view) (location; size; cooling water; road access; fuel transport; construction; employment; environment; screening; the next steps (licensing procedures, etc.); safety; further information). (U.K.)

VALIDATION OF FULL CORE GEOMETRY MODEL OF THE NODAL3 CODE IN THE PWR TRANSIENT BENCHMARK PROBLEMS

Directory of Open Access Journals (Sweden)

Tagor Malem Sembiring

2015-10-01

Full Text Available ABSTRACT VALIDATION OF FULL CORE GEOMETRY MODEL OF THE NODAL3 CODE IN THE PWR TRANSIENT BENCHMARK PROBLEMS. The coupled neutronic and thermal-hydraulic (T/H code, NODAL3 code, has been validated in some PWR static benchmark and the NEACRP PWR transient benchmark cases. However, the NODAL3 code have not yet validated in the transient benchmark cases of a control rod assembly (CR ejection at peripheral core using a full core geometry model, the C1 and C2 cases.  By this research work, the accuracy of the NODAL3 code for one CR ejection or the unsymmetrical group of CRs ejection case can be validated. The calculations by the NODAL3 code have been carried out by the adiabatic method (AM and the improved quasistatic method (IQS. All calculated transient parameters by the NODAL3 code were compared with the reference results by the PANTHER code. The maximum relative difference of 16% occurs in the calculated time of power maximum parameter by using the IQS method, while the relative difference of the AM method is 4% for C2 case.  All calculation results by the NODAL3 code shows there is no systematic difference, it means the neutronic and T/H modules are adopted in the code are considered correct. Therefore, all calculation results by using the NODAL3 code are very good agreement with the reference results. Keywords: nodal method, coupled neutronic and thermal-hydraulic code, PWR, transient case, control rod ejection.   ABSTRAK VALIDASI MODEL GEOMETRI TERAS PENUH PAKET PROGRAM NODAL3 DALAM PROBLEM BENCHMARK GAYUT WAKTU PWR. Paket program kopel neutronik dan termohidraulika (T/H, NODAL3, telah divalidasi dengan beberapa kasus benchmark statis PWR dan kasus benchmark gayut waktu PWR NEACRP.  Akan tetapi, paket program NODAL3 belum divalidasi dalam kasus benchmark gayut waktu akibat penarikan sebuah perangkat batang kendali (CR di tepi teras menggunakan model geometri teras penuh, yaitu kasus C1 dan C2. Dengan penelitian ini, akurasi paket program

CRC DEPLETION CALCULATIONS FOR THE RODDED ASSEMBLIES IN BATCHES 1, 2, 3, AND 1X OF CRYSTAL RIVER UNIT 3

Energy Technology Data Exchange (ETDEWEB)

Kenneth D. Wright

1997-09-03

The purpose of this design analysis is to document the SAS2H depletion calculations of certain rodded fuel assemblies from batches 1, 2, 3, and 1X of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A rodded assembly is one that contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) for some period of time during its irradiation history. The objective of this analysis is to provide SAS2H calculated isotopic compositions of depleted fuel and depleted burnable poison for each fuel assembly to be used in subsequent CRC reactivity calculations containing the fuel assemblies.

CRC DEPLETION CALCULATIONS FOR THE RODDED ASSEMBLIES IN BATCHES 1, 2, 3, AND 1X OF CRYSTAL RIVER UNIT 3

International Nuclear Information System (INIS)

Wright, Kenneth D.

1997-01-01

The purpose of this design analysis is to document the SAS2H depletion calculations of certain rodded fuel assemblies from batches 1, 2, 3, and 1X of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A rodded assembly is one that contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) for some period of time during its irradiation history. The objective of this analysis is to provide SAS2H calculated isotopic compositions of depleted fuel and depleted burnable poison for each fuel assembly to be used in subsequent CRC reactivity calculations containing the fuel assemblies

An economic analysis code used for PWR fuel cycle

International Nuclear Information System (INIS)

Liu Dingqin

1989-01-01

An economic analysis code used for PWR fuel cycle is developed. This economic code includes 12 subroutines representing vavious processes for entire PWR fuel cycle, and indicates the influence of the fuel cost on the cost of the electricity generation and the influence of individual process on the sensitivity of the fuel cycle cost

Waste generation comparison: Coal-fired versus nuclear power plants

International Nuclear Information System (INIS)

LaGuardia, T.S.

1998-01-01

Low-level radioactive waste generation and disposal attract a great deal of attention whenever the nuclear industry is scrutinized by concerned parties, be it the media, the public, or political interests. It is therefore important to the nuclear industry that this issue be put into perspective relative to other current forms of energy production. Most of the country's fossil-fueled power comes from coal-fired plants, with oil and gas as other fuel sources. Most of the generated waste also comes from coal plants. This paper, therefore, compares waste quantities generated by a typical (1150-MW(electric)) pressurized water reactor (PWR) to that of a comparably sized coal-fired power plant

Processing of nuclear power plant waste streams containing boric acid

International Nuclear Information System (INIS)

1996-10-01

Boric acid is used in PWR type reactor's primary coolant circuit to control the neutron flux. However, boric acid complicates the control of water chemistry of primary coolant and the liquid radioactive waste produced from NPP. The purpose of this report is to provide member states with up-to-date information and guidelines for the treatment and conditioning of boric acid containing wastes. It contains chapters on: (a) characteristics of waste streams; (b) options for management of boric acid containing waste; (c) treatment/decontamination of boric acid containing waste; (d) concentration and immobilization of boric acid containing waste; (e) recovery and re-use of boric acid; (f) selected industrial processes in various countries; and (g) the influence of economic factors on process selection. 72 refs, 23 figs, 5 tabs

Irradiation behavior of German PWR RPV steels under operating conditions

Energy Technology Data Exchange (ETDEWEB)

May, J.; Hein, H. [AREVA NP Gmbh (Germany); Ganswind, J. [VGB PowerTech e.V. (Germany); Widera, M. [RWE Power AG (Germany)

2011-07-01

In 2007, the last standard surveillance capsule of the original RPV (Reactor Pressure Vessel) surveillance programs of the 11 currently operating German PWR has been evaluated. With it the standard irradiation surveillance programs of these plants was completed. In the present paper, irradiation data of these surveillance programs will be presented and a final assessment of the irradiation behavior of the German PWR RPV steels with respect to current standards KTA 3203 and Reg. Guide 1.99 Rev. 2 will be given. Data from two units which are currently under decommissioning will also be included, so that data from all 13 German PWR manufactured by the former Siemens/KWU company (now AREVA NP GmbH) are shown. It will be shown that all surveillance data within the approved area of chemical composition verify the limit curve RT(limit) of the KTA 3203, which is the relevant safety standard for these plants. An analysis of the data shows, that the prediction formulas of Reg. Guide 1.99 Rev. 2 Pos. 1 or from the TTS model tend to overestimate the irradiation behavior of the German PWR RPV steels. Possible reasons for this behavior are discussed. Additionally, the data will be compared to data from the research project CARISMA to demonstrate that these data are representative for the irradiation behavior of the German PWR RPV steels. Since the data of these research projects cover a larger neutron fluence range than the original surveillance data, they offer a future outlook into the irradiation behavior of the German PWR RPV steels under long term conditions. In general, as a consequence of the relatively large and beneficial water gap between core and RPV, especially in all Siemens/KWU 4-loop PWR, the EOL neutron fluence and therefore the irradiation induced changes in mechanical properties of the German PWR RPV materials are rather low. Moreover the irradiation data indicate that the optimized RPV materials specifications that have been applied in particular for the

Revised uranium--plutonium cycle PWR and BWR models for the ORIGEN computer code

International Nuclear Information System (INIS)

Croff, A.G.; Bjerke, M.A.; Morrison, G.W.; Petrie, L.M.

1978-09-01

Reactor physics calculations and literature searches have been conducted, leading to the creation of revised enriched-uranium and enriched-uranium/mixed-oxide-fueled PWR and BWR reactor models for the ORIGEN computer code. These ORIGEN reactor models are based on cross sections that have been taken directly from the reactor physics codes and eliminate the need to make adjustments in uncorrected cross sections in order to obtain correct depletion results. Revised values of the ORIGEN flux parameters THERM, RES, and FAST were calculated along with new parameters related to the activation of fuel-assembly structural materials not located in the active fuel zone. Recommended fuel and structural material masses and compositions are presented. A summary of the new ORIGEN reactor models is given

A Calculation of the radioactivity induced in PWR cluster control rods with the origin and casmo codes

International Nuclear Information System (INIS)

Ekberg, K.

1980-03-01

The radioactivity induced in PWR cluster control rods during reactor operation has been calculated using the computer programme ORIGEN. Neutron fluxes and spectrum conditions as well as the strongly shielded cross sections for the absorber materials Ag, In and Cd have been obtained by running the cell and assembly code CASMO for a couple of typical cases. The results show that Ag-110m, Fe-55 and Co-60 give the largest activity contributions in the interval 1-10 years after the end of irradiation, and Ni-63 and Cd-113m in a longer time perspective. (author)

Criticality coefficient calculation for a small PWR using Monte Carlo Transport Code

Energy Technology Data Exchange (ETDEWEB)

Trombetta, Debora M.; Su, Jian, E-mail: dtrombetta@nuclear.ufrj.br, E-mail: sujian@nuclear.ufrj.br [Coordenacao dos Programas de Pos-Graduacao em Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil); Chirayath, Sunil S., E-mail: sunilsc@tamu.edu [Department of Nuclear Engineering and Nuclear Security Science and Policy Institute, Texas A and M University, TX (United States)

2015-07-01

Computational models of reactors are increasingly used to predict nuclear reactor physics parameters responsible for reactivity changes which could lead to accidents and losses. In this work, preliminary results for criticality coefficient calculation using the Monte Carlo transport code MCNPX were presented for a small PWR. The computational modeling developed consists of the core with fuel elements, radial reflectors, and control rods inside a pressure vessel. Three different geometries were simulated, a single fuel pin, a fuel assembly and the core, with the aim to compare the criticality coefficients among themselves.The criticality coefficients calculated were: Doppler Temperature Coefficient, Coolant Temperature Coefficient, Coolant Void Coefficient, Power Coefficient, and Control Rod Worth. The coefficient values calculated by the MCNP code were compared with literature results, showing good agreement with reference data, which validate the computational model developed and allow it to be used to perform more complex studies. Criticality Coefficient values for the three simulations done had little discrepancy for almost all coefficients investigated, the only exception was the Power Coefficient. Preliminary results presented show that simple modelling as a fuel assembly can describe changes at almost all the criticality coefficients, avoiding the need of a complex core simulation. (author)

PWR plant construction in Japan

International Nuclear Information System (INIS)

Tamura, Toshifumi

2002-01-01

The construction methods based on the experiences on the Nuclear Island, which is a critical path in the total construction schedule, have been studied and reconsidered in order to construct by more reliable and economical method. So various improved construction method are being applied and the duration of construction is being reduced continuously. So various improved construction method are being applied and the duration of construction is being reduced continuously. In this paper, the history of construction of twenty-three (23) PWR Plant, the actual construction methods and schedule of Ohi-3/4, to which the many improved methods were applied during their construction, are introduced mainly with the improved points for previously constructed plants. And also the situation of construction method for the next PWR Plant is simply explained

Full vessel CFD analysis on thermal-hydraulic characteristics of CPR1000 PWR

International Nuclear Information System (INIS)

Chao Yanmeng; Yang Lixin; Zhang Mingqian

2014-01-01

To obtain flow distributions and thermal-hydraulic properties in a full vessel PWR under limited computation ability and time, a full vessel simulation model of CPR1000 was built based on two simplification methods. One simplified the inner geometry of the control rod guide tubes using equivalent flow area. Another substituted the core by a porous domain to maintain the pressure drop and temperature rise. After the computation, global and localized flow distributions, hydraulic loads of some main assemblies were obtained, as well as other thermal-hydraulic properties. The results indicate the flow distribution in the full vessel is asymmetrical. Therefore it is essential to use the full vessel model to simulate. The calculated thermal-hydraulic characteristics agree well with the operation statistics, providing the reference data for the reactor safety operation. (authors)

Basic study on characteristics of some important equilibrium fuel cycles of PWR

International Nuclear Information System (INIS)

Waris, A.; Sekimoto, H.

2001-01-01

Equilibrium fuel cycle characteristics of a light water reactor (LWR) with enriched uranium supply were evaluated. In this study, five kinds of fuel cycles of 3000 MWt pressurized water reactor (PWR) were investigated, and a method to determine the uranium enrichment in order to achieve their criticality was presented. The results show that the enrichment decreases considerably with increasing number of confined heavy nuclides when U is discharged from the reactor. The required natural uranium was also evaluated for two different enrichment processes. The amount of required natural uranium also decreases as well. On the other hand, when U is totally confined, the enrichment becomes unacceptably high. Furthermore, Pu and minor actinides (MA) confining seem effective to incinerate the discharged radio-toxic wastes

Improved emergency elevated air release for simplified PWR

International Nuclear Information System (INIS)

Naitoh, T.; Bruce, R.A.; Hirota, K.; Tajiri, Y.

1992-01-01

In developing the application of the simplified PWR in Japan, one of the most important areas is to limit post-accident site boundary whole body dose. In addressing this, the concept of Emergency Passive Air Filtration System (EPAFS) and it's feasibility is developed. The efficiency of charcoal filtering and the atmospheric diffusion effect of an elevated air release are important for dose reduction. The performance of these functions was evaluated by confirmatory testing. The test results confirmed a 99 percent efficiency of charcoal filter and an atmospheric diffusion effect higher than that of a conventional plant. The Emergency Passive Air Filtration System (EPAFS) and the atmospheric diffusion effect of elevated air release contribute to making the calculated post-accident site boundary whole body dose of simplified PWR as low as that of the conventional Japanese PWR plant. (author)

Experience in industrial operation of the plant for immobilizing radioactive wastes in thermosetting resins at the Ardennes Nuclear Power Station

International Nuclear Information System (INIS)

Haller, P.; Romestain, P.; Bruant, J.P.

1983-01-01

The French Atomic Energy Commission (CEA) has developed, at the Grenoble Centre for Nuclear Studies, a procedure for immobilizing low- and intermediate-level wastes in thermosetting resins of the polyester or epoxy types. To demonstrate feasibility on an industrial scale, a pilot plant has been set up at the effluent treatment station of the Ardennes Franco-Belgium Nuclear Power Station (SENA), which is a 305 MW(e) PWR type. Assembly work began in January 1979. After a period devoted to final adjustments and operation with inactive products, conditioning of active products began in January 1981. In the paper, the methods of conditioning the three types of waste (evaporation concentrates, ion exchange resins and filter cartridges) are described, experience of the start-up and operation of the plant is reported and the principal results of coating characterization tests are given. The results of tests on active and inactive products show that the characteristics of the materials obtained on an industrial scale match those of laboratory products and confirm their high quality with regard to mechanical behaviour, fire resistance, homogeneity and low-leachability. Industrial experience and economic comparisons show that the process of immobilizing waste from nuclear power stations in thermosetting resins offers an extremely interesting alternative to classical methods of conditioning. (author)

The simulation research for the dynamic performance of integrated PWR

International Nuclear Information System (INIS)

Yuan Jiandong; Xia Guoqing; Fu Mingyu

2005-01-01

The mathematical model of the reactor core of integrated PWR has been studied and simplified properly. With the lumped parameter method, authors have established the mathematical model of the reactor core, including the neutron dynamic equation, the feedback reactivities model and the thermo-hydraulic model of the reactor. Based on the above equations and models, the incremental transfer functions of the reactor core model have been built. By simulation experimentation, authors have compared the dynamic characteristics of the integrated PWR with the traditional dispersed PWR. The simulation results show that the mathematical models and equations are correct. (authors)

Estimate of the Sources of Plutonium-Containing Wastes Generated from MOX Fuel Production in Russia

International Nuclear Information System (INIS)

Kudinov, K. G.; Tretyakov, A. A.; Sorokin, Yu. P.; Bondin, V. V.; Manakova, L. F.; Jardine, L. J.

2002-01-01

In Russia, mixed oxide (MOX) fuel is produced in a pilot facility ''Paket'' at ''MAYAK'' Production Association. The Mining-Chemical Combine (MCC) has developed plans to design and build a dedicated industrial-scale plant to produce MOX fuel and fuel assemblies (FA) for VVER-1000 water reactors and the BN-600 fast-breeder reactor, which is pending an official Russian Federation (RF) site-selection decision. The design output of the plant is based on a production capacity of 2.75 tons of weapons plutonium per year to produce the resulting fuel assemblies: 1.25 tons for the BN-600 reactor FAs and the remaining 1.5 tons for VVER-1000 FAs. It is likely the quantity of BN-600 FAs will be reduced in actual practice. The process of nuclear disarmament frees a significant amount of weapons plutonium for other uses, which, if unutilized, represents a constant general threat. In France, Great Britain, Belgium, Russia, and Japan, reactor-grade plutonium is used in MOX-fuel production. Making MOX-fuel for CANDU (Canada) and pressurized water reactors (PWR) (Europe) is under consideration in Russia. If this latter production is added, as many as 5 tons of Pu per year might be processed into new FAs in Russia. Many years of work and experience are represented in the estimates of MOX fuel production wastes derived in this report. Prior engineering studies and sludge treatment investigations and comparisons have determined how best to treat Pu sludges and MOX fuel wastes. Based upon analyses of the production processes established by these efforts, we can estimate that there will be approximately 1200 kg of residual wastes subject to immobilization per MT of plutonium processed, of which approximately 6 to 7 kg is Pu in the residuals per MT of Pu processed. The wastes are various and complicated in composition. Because organic wastes constitute both the major portion of total waste and of the Pu to be immobilized, the recommended treatment of MOX-fuel production waste is

Estimate of the Sources of Plutonium-Containing Wastes Generated from MOX Fuel Production in Russia

Energy Technology Data Exchange (ETDEWEB)

Kudinov, K. G.; Tretyakov, A. A.; Sorokin, Yu. P.; Bondin, V. V.; Manakova, L. F.; Jardine, L. J.

2002-02-26

In Russia, mixed oxide (MOX) fuel is produced in a pilot facility ''Paket'' at ''MAYAK'' Production Association. The Mining-Chemical Combine (MCC) has developed plans to design and build a dedicated industrial-scale plant to produce MOX fuel and fuel assemblies (FA) for VVER-1000 water reactors and the BN-600 fast-breeder reactor, which is pending an official Russian Federation (RF) site-selection decision. The design output of the plant is based on a production capacity of 2.75 tons of weapons plutonium per year to produce the resulting fuel assemblies: 1.25 tons for the BN-600 reactor FAs and the remaining 1.5 tons for VVER-1000 FAs. It is likely the quantity of BN-600 FAs will be reduced in actual practice. The process of nuclear disarmament frees a significant amount of weapons plutonium for other uses, which, if unutilized, represents a constant general threat. In France, Great Britain, Belgium, Russia, and Japan, reactor-grade plutonium is used in MOX-fuel production. Making MOX-fuel for CANDU (Canada) and pressurized water reactors (PWR) (Europe) is under consideration in Russia. If this latter production is added, as many as 5 tons of Pu per year might be processed into new FAs in Russia. Many years of work and experience are represented in the estimates of MOX fuel production wastes derived in this report. Prior engineering studies and sludge treatment investigations and comparisons have determined how best to treat Pu sludges and MOX fuel wastes. Based upon analyses of the production processes established by these efforts, we can estimate that there will be approximately 1200 kg of residual wastes subject to immobilization per MT of plutonium processed, of which approximately 6 to 7 kg is Pu in the residuals per MT of Pu processed. The wastes are various and complicated in composition. Because organic wastes constitute both the major portion of total waste and of the Pu to be immobilized, the recommended treatment

PWR core design calculations

International Nuclear Information System (INIS)

Trkov, A.; Ravnik, M.; Zeleznik, N.

1992-01-01

Functional description of the programme package Cord-2 for PWR core design calculations is presented. Programme package is briefly described. Use of the package and calculational procedures for typical core design problems are treated. Comparison of main results with experimental values is presented as part of the verification process. (author) [sl

Disposal of high level and intermediate level radioactive wastes

International Nuclear Information System (INIS)

Flowers, R.H.

1991-01-01

The waste products from the nuclear industry are relatively small in volume. Apart from a few minor gaseous and liquid waste streams, containing readily dispersible elements of low radiotoxicity, all these products are processed into stable solid packages for disposal in underground repositories. Because the volumes are small, and because radioactive wastes are latecomers on the industrial scene, a whole new industry with a world-wide technological infrastructure has grown up alongside the nuclear power industry to carry out the waste processing and disposal to very high standards. Some of the technical approaches used, and the Regulatory controls which have been developed, will undoubtedly find application in the future to the management of non-radioactive toxic wastes. The repository site outlined would contain even high-level radioactive wastes and spent fuels being contained without significant radiation dose rates to the public. Water pathway dose rates are likely to be lowest for vitrified high-level wastes with spent PWR fuel and intermediate level wastes being somewhat higher. (author)

Road-map design for thorium-uranium breeding recycle in PWR - 031

International Nuclear Information System (INIS)

Shengyi, Si

2010-01-01

The paper was focused on designing a road-map to finally approach sustainable Thorium-Uranium ( 232 Th- 233 U) Breeding Recycle in current PWR, without any other change to the fuel lattice and the core internals, but substituting the UOX pellet with Thorium-based pellet. At first, the paper presented some insights to the inherence of Thorium-Uranium fuel conversion or breeding in PWR based on the neutronics theory and revealed the prerequisites for Thorium-Uranium fuel in PWR to achieve sustainable Breeding Recycle; And then, various Thorium-based fuels were designed and examined, and the calculation results further validated the above theoretical deductions; Based on the above theoretical analysis and calculation results, a road-map for sustainable Thorium-Uranium breeding recycle in PWR was outlined finally. (authors)

Influence of boron reduction strategies on PWR accident management flexibility

International Nuclear Information System (INIS)

Papukchiev, Angel Aleksandrov; Liu, Yubo; Schaefer, Anselm

2007-01-01

In conventional pressurized water reactor (PWR) designs, soluble boron is used for reactivity control over core fuel cycle. Design changes to reduce boron concentration in the reactor coolant are of general interest regarding three aspects - improved reactivity feedback properties, lower impact of boron dilution scenarios on PWR safety and eventually more flexible accident management procedures. In order to assess the potential advantages through the introduction of boron reduction strategies in current PWRs, two low boron core configurations based on fuel with increased utilization of gadolinium and erbium burnable absorbers have been developed. The new PWR designs permit to reduce the natural boron concentration in reactor coolant at begin of cycle to 518 ppm and 805 ppm. For the assessment of the potential safety advantages of these cores a hypothetical beyond design basis accident has been simulated with the system code ATHLET. The analyses showed improved inherent safety and increased accident management flexibility of the low boron cores in comparison with the standard PWR. (author)

The VEGA Assembly Spectrum Code

International Nuclear Information System (INIS)

Milosevic, M.

1997-01-01

The VEGA is assembly spectrum code, developed as a design tool for producing a few-group averaged cross section data for a wide range of reactor types including both thermal and fast reactors. It belongs to a class of codes, which may be characterized by the separate stages for micro group, spectrum and macro group assembly calculations. The theoretical foundation for the development of the VEGA code was integral transport theory in the first-flight collision probability formulation. Two versions of VEGA are now in use, VEGA-1 established on standard equivalence theory and VEGA-2 based on new subgroup method applicable for any geometry for which a flux solution is possible. This paper describes a features which are unique to the VEGA codes with concentration on the basic principles and algorithms used in the proposed subgroup method. Presented validation of this method, comprise the results for a homogenous uranium-plutonium mixture and a PWR cell containing a recycled uranium-plutonium oxide. Example application for a realistic fuel dissolver benchmark problem , which was extensive analyzed in the international calculations, is also included. (author)

Preliminary performance analysis of exponential experimental system for the determination of neutron effective multiplication factor of PWR spent fuel

International Nuclear Information System (INIS)

Shin, Heesung; Lee, Sang-Yun; Ro, Seung-Gy; Seo, Gi-Seok; Kim, Ho-Dong

2002-01-01

An exponential experiment system which is composed of neutron detector, signal analysis system and neutron source, 10 mCi Cf-252 has been installed in the storage pool of PIEF at KAERI in order to experimentally determining neutron effective multiplication factors of PWR spent fuel assemblies. Preliminary functional characteristic tests of the experimental system are performed for C15, J14 and J44 assemblies loaded in the pool. As a result of preliminary tests, the average neutron counts obtained for 3 minutes in the plateau of the C15, J14 and J44 assemblies are about 1900, 3800 and 3200, respectively. A dip of the neutron flux density distribution is noticed in the spacer grid position. Neutron counts at those positions appear to be reduced to about 70 % in comparison to the fuel position. The measured axial neutron distribution shapes are compared with the result for the P14 assembly and Cs-137 gamma scanning data performed in KAERI. It is revealed that the spacer grid position measured is consistent with the design specifications within a 2.3 % error. The exponential decay constants for the C15 assembly were determined to be 0.152 and 0.165 for detector and source scanning, respectively. (author)

Nondestructive examination requirements for PWR vessel internals

International Nuclear Information System (INIS)

Spanner, J.

2015-01-01

This paper describes the requirements for the nondestructive examination of pressurized water reactor (PWR) vessel internals in accordance with the requirements of the EPRI Material Reliability Program (MRP) inspection standard for PWR internals (MRP-228) and the American Society of Mechanical Engineers Section XI In-service Inspection. The MRP vessel internals examinations have been performed at nuclear plants in the USA since 2009. The objective of the inspection standard is to provide the requirements for the nondestructive examination (NDE) methods implemented to support the inspection and evaluation of the internals. The inspection standard contains requirements specific to the inspection methodologies involved as well as requirements for qualification of the NDE procedures, equipment and personnel used to perform the vessel internals inspections. The qualification requirements for the NDE systems will be summarized. Six PWR plants in the USA have completed inspections of their internals using the Inspection and Evaluation Guideline (MRP-227) and the Inspection Standard (MRP-228). Examination results show few instances of service-induced degradation flaws, as expected. The few instances of degradation have mostly occurred in bolting

The actual practice of air cleaning in Belgian nuclear facilities

Energy Technology Data Exchange (ETDEWEB)

Goossens, W.R. [PEGO, Mol (Belgium)

1995-02-01

With 60% of its power generation from nuclear stations Belgium has 7 nuclear power stations in operation with a total capacity of 5.4 MWe. Enriched uranium is imported and converted to fuel assemblies. The actinides of reprocessed fuel are recycled as MOX fuel. A main waste conditioning operation has been performed in the PAMELA vitrifier. The actual practice of nuclear air cleaning in the Belgian PWR station DOEL-4 and in the PAMELA -vitrification plant for high level liquid waste is reviewed.

Parameterized representation of macroscopic cross section for PWR reactor

International Nuclear Information System (INIS)

Fiel, João Cláudio Batista; Carvalho da Silva, Fernando; Senra Martinez, Aquilino; Leal, Luiz C.

2015-01-01

Highlights: • This work describes a parameterized representation of the homogenized macroscopic cross section for PWR reactor. • Parameterization enables a quick determination of problem-dependent cross-sections to be used in few group calculations. • This work allows generating group cross-section data to perform PWR core calculations without computer code calculations. - Abstract: The purpose of this work is to describe, by means of Chebyshev polynomials, a parameterized representation of the homogenized macroscopic cross section for PWR fuel element as a function of soluble boron concentration, moderator temperature, fuel temperature, moderator density and 235 92 U enrichment. The cross-section data analyzed are fission, scattering, total, transport, absorption and capture. The parameterization enables a quick and easy determination of problem-dependent cross-sections to be used in few group calculations. The methodology presented in this paper will allow generation of group cross-section data from stored polynomials to perform PWR core calculations without the need to generate them based on computer code calculations using standard steps. The results obtained by the proposed methodology when compared with results from the SCALE code calculations show very good agreement

Consequences of mis-loading and the power distribution in bowed fuel assemblies

International Nuclear Information System (INIS)

Andersson, Magnus

2002-04-01

The thesis is divided in two parts. The first part will investigate consequences of a mis-loaded fuel assembly in Ringhals 3, which is a pressurised water reactor (PWR). The aim of this work is to show that there are no or very small benefits from making an additional flux map at 30 % power in order to detect anomalies. Out of the 17 simulations, there exists only one type of mis-loading, which leads to problems. The case, which leads to problems, is when a Gd fitted assembly changes place with a non Gd. This leads to a too high power peaking factor and increased quadrant power tilt. The gain of a flux map at 30% power is small

Consequences of mis-loading and the power distribution in bowed fuel assemblies

Energy Technology Data Exchange (ETDEWEB)

Andersson, Magnus

2002-04-01

The thesis is divided in two parts. The first part will investigate consequences of a mis-loaded fuel assembly in Ringhals 3, which is a pressurised water reactor (PWR). The aim of this work is to show that there are no or very small benefits from making an additional flux map at 30 % power in order to detect anomalies. Out of the 17 simulations, there exists only one type of mis-loading, which leads to problems. The case, which leads to problems, is when a Gd fitted assembly changes place with a non Gd. This leads to a too high power peaking factor and increased quadrant power tilt. The gain of a flux map at 30% power is small.

Underground disposal of UK heat-generating wastes: repository design considerations

International Nuclear Information System (INIS)

Steadman, J.A.

1993-12-01

The report discusses the likely differences in design between a deep repository for disposal of UK heat-generating radioactive wastes and that of the planned Nirex ILW/LLW repository at Sellafield, based on a review of international published information. The main differences arise from the greater heat and radiation outputs of the waste, and in the case of intact PWR spent fuel elements, the greater length and weight of the disposal packages. Published cost estimates for other OECD countries for disposal of heat-generating wastes are considerably lower than that for the UK, partly because in most cases they are for co-disposal with a larger quantity of ILW. (author)

Characterization of low and medium-level radioactive waste forms. Joint annual progress report 1982

International Nuclear Information System (INIS)

Vejmelka, P.; Sambell, R.A.J.

1984-01-01

The work reported was carried out during the second year of the Commission of the European Communities programme on the characterization of low and medium-level waste forms. Ten reference waste forms plus others of special national interest have been identified covering PWR, BWR, GCR and reprocessing wastes. The immobilizing media include the three main matrices: cement, polymers and bitumen, and a glass. Characterization is viewed as one input to quality assurance of the waste form and covers: waste-matrix compatibility, radiation effects, leaching, microbiological attack, shrinkage and swelling, ageing processes and thermal effects. The aim is a balanced programme of comparative data, predictive modelling and an understanding of basic mechanisms

The research on burnup characteristic of doping burnable poison in PWR

International Nuclear Information System (INIS)

Qiang Shenglong; Qin Dong; Chai Xiaoming; Yao Dong

2014-01-01

In PWR core design, burnable poisons are usually used for reactive compensation and power flatten. The choice of burnable poisons and how to match burnup would be the key-points for a long-life core design. We study the burnup character of doping burnable poisons (such as natural element, manual nuclide and soluble boron) in the PWR by the core burnup code MOI based on Monte Carlo method. The results show that Hf, Er and Eu doping burnable poison would be applicable for the nuclear design research on the long-life PWR core. (authors)

Neutron multiplication and shielding problems in PWR spent-fuel shipping casks

International Nuclear Information System (INIS)

Devillers, C.

1976-01-01

In order to evaluate the degree of accuracy of computational methods used for the shield design of spent-fuel shipping casks, comparisons were made between biological dose rate calculations and measurements at the surface of a cask carrying three PWR fuel assemblies (the fuel being successively wet and dry). The experimental methods used provide ksub(eff) with an accuracy of 0.024. Neutron multiplication coefficients provided by the APOLLO and DOT-3 codes are located within the uncertainty range of the experimentally derived values. The APOLLO plus DOT codes for neutron source calculations and ANISN plus DOT codes for neutron transmission calculations provide neutron dose rate predictions in agreement with measurements to within 10%. The PEPIN 76 code used for deriving fission product γ-rays and the point kernel code MERCURE 4 treating the γ-ray transmission give γ dose rate predictions that generally differ from measurements by less than 25%

Bituminization process of radioactive liquid wastes by domestic bitumen

International Nuclear Information System (INIS)

Sang, H.L.

1977-11-01

A study has been carried out of the incorporation of intermediate level wastes in bitumen. Two kinds of wastes: a) an evaporator concentrate from a PWR (containing boric acid), b) second cycle wastes from the Purex process (containing sodium salts), were satisfactorily incorporated into a mixture of straight and blown domestic bitumen, to yield a product containing 50wt% solids. The products were stable to radiation exposure of 5'8x10 8 rads. Leach rates were measured in both distilled and sea water over periods up to 200 days at 5 0 C and 25 0 C and at both 1 atm and 8 atm pressure. Results confirmed that long term storage of the products would be satisfactory

Seismic analysis with FEM for fuel transfer system of PWR nuclear power plant

International Nuclear Information System (INIS)

Jia Xiaofeng; Liu Pengliang; Bi Xiangjun; Ji Shunying

2012-01-01

In the PWR nuclear power plant, the function of the fuel transfer system (FTS) is to transfer the fuel assembly between the reactor building and the fuel building. The seismic analysis of the transfer system structure should be carried out to ensure the safety under OBE and SSE. Therefore, the ANASYS 12.0 software is adopted to construct the finite element analysis model for the fuel transfer system in a million kilowatt nuclear power plant. For the various configurations of FTS in the operating process, the stresses of the main structures, such as the transfer tube, fuel assembly container, fuel conveyor car, lifting frame in the reactor building, lifting frame in the fuel building, support and guide structure of conveyor car and the lifting frame in both buildings, are computed. The stresses are combined with the method of square root of square sum (SRSS) and assessed under various seismic conditions based on RCCM code, the results of the assessment satisfy the code. The results show that the stresses of the fuel transfer system structure meet the strength requirement, meanwhile, it can withstand the earthquake well. (authors)

Cylindrization of a PWR core for neutronic calculations

International Nuclear Information System (INIS)

Santos, Rubens Souza dos

2005-01-01

In this work we propose a core cylindrization, starting from a PWR core configuration, through the use of an algorithm that becomes the process automated in the program, independent of the discretization. This approach overcomes the problem stemmed from the use of the neutron transport theory on the core boundary, in addition with the singularities associated with the presence of corners on the outer fuel element core of, existents in the light water reactors (LWR). The algorithm was implemented in a computational program used to identification of the control rod drop accident in a typical PWR core. The results showed that the algorithm presented consistent results comparing with an production code, for a problem with uniform properties. In our conclusions, we suggest, for future works, for analyzing the effect on mesh sizes for the Cylindrical geometry, and to compare the transport theory calculations versus diffusion theory, for the boundary conditions with corners, for typical PWR cores. (author)

Buildup of radioxenon isotopes in MOX-assemblies

Energy Technology Data Exchange (ETDEWEB)

Gniffke, Thomas; Kirchner, Gerald [Carl Friedrich von Weizsaecker-Centre for Science and Peace Research, Hamburg (Germany)

2015-07-01

Radioxenon is the main tracer for detection of nuclear tests conducted underground under the verification regime of the Comprehensive Nuclear Test Ban Treaty (CTBT). Since radioxenon is emitted by civilian sources too, like commercial nuclear reactors, source discrimination is still an important issue. Inventory calculations are necessary to predict which xenon isotopic ratios are built up in a reactor and how they differ from those generated by a nuclear explosion. The screening line actually used by the CTBT Organization for source discrimination is based on calculations for uranium fuel of various enrichments used in pressurized water reactors (PWRs). The usage of different fuel, especially mixed U/Pu oxide (MOX) assemblies with reprocessed plutonium, may alter the radioxenon signature of civilian reactors. In this talk, calculations of the radioxenon buildup in a MOX-assembly used in a commercial PWR are presented. Implications for the CTBT verification regimes are discussed and open questions are addressed.

Safety aspects of the using Gd as burnable poison in PWR's

International Nuclear Information System (INIS)

Vandenberg, C.; Bonet, H.; Charlier, A.

1978-01-01

The experience of BELGONUCLEAIRE in using Gd in LWR's has indicated the safety related advantages of this burnable poison. The successfully operation of the BR3 PWR power plant with 5% of Gd rods is presented and extrapolated to large PWR's. (authro)

Calculation of source term in spent PWR fuel assemblies for dry storage and shipping cask design; Calculo de los terminos fuente de combustibles irradiados PWR para el diseno de contenedores de almacenamiento y transporte

Energy Technology Data Exchange (ETDEWEB)

Fernandez, J L; Lopez, J

1986-07-01

Using the ORIGEN-2 Coda, the decay heat and neutron and photon sources for an irradiated PWR fuel element have been calculated. Also, parametric studies on the behaviour of the magnitudes with the burn-up, linear heat power and irradiation and cooling times were performed. Finally, a comparison between our results and other design calculations shows a good agreement and confirms the validity of the used method. (Author) 6 refs.

PACTEL and PWR PACTEL Test Facilities for Versatile LWR Applications

Directory of Open Access Journals (Sweden)

Virpi Kouhia

2012-01-01

Full Text Available This paper describes construction and experimental research activities with two test facilities, PACTEL and PWR PACTEL. The PACTEL facility, comprising of reactor pressure vessel parts, three loops with horizontal steam generators, a pressurizer, and emergency core cooling systems, was designed to model the thermal-hydraulic behaviour of VVER-440-type reactors. The facility has been utilized in miscellaneous applications and experiments, for example, in the OECD International Standard Problem ISP-33. PACTEL has been upgraded and modified on a case-by-case basis. The latest facility configuration, the PWR PACTEL facility, was constructed for research activities associated with the EPR-type reactor. A significant design basis is to utilize certain parts of PACTEL, and at the same time, to focus on a proper construction of two new loops and vertical steam generators with an extensive instrumentation. The PWR PACTEL benchmark exercise was launched in 2010 with a small break loss-of-coolant accident test as the chosen transient. Both facilities, PACTEL and PWR PACTEL, are maintained fully operational side by side.

PACTEL and PWR PACTEL Test Facilities for Versatile LWR Applications

International Nuclear Information System (INIS)

Virpi Kouhia, V.; Purhonen, H.; Riikonen, V.; Puustinen, M.; Kyrki-Rajamaki, R.; Vihavainen, J.

2012-01-01

This paper describes construction and experimental research activities with two test facilities, PACTEL and PWR PACTEL. The PACTEL facility, comprising of reactor pressure vessel parts, three loops with horizontal steam generators, a pressurizer, and emergency core cooling systems, was designed to model the thermal-hydraulic behaviour of VVER-440-type reactors. The facility has been utilized in miscellaneous applications and experiments, for example, in the OECD International Standard Problem ISP-33. PACTEL has been upgraded and modified on a case-by-case basis. The latest facility configuration, the PWR PACTEL facility, was constructed for research activities associated with the EPR-type reactor. A significant design basis is to utilize certain parts of PACTEL, and at the same time, to focus on a proper construction of two new loops and vertical steam generators with an extensive instrumentation. The PWR PACTEL benchmark exercise was launched in 2010 with a small break loss-of-coolant accident test as the chosen transient. Both facilities, PACTEL and PWR PACTEL, are maintained fully operational side by side.

Design of the Flow Plates for a Dual Cooled Fuel Assembly

International Nuclear Information System (INIS)

Kim, Jae Yong; Yoon, Kyung Ho; Lee, Young Ho; Lee, Kang Hee; Kim, Hyung Kyu

2009-01-01

In a dual cooled fuel assembly, the array and position of fuels are changed from those of a conventional PWR fuel assembly to achieve a power uprating. The flow plate provides flow holes to direct the heated coolant into/out of the fuel assembly and structural intensity to insure that the fuel rod is axially restrained within the spacer grids. So, flow plates of top/bottom end pieces (TEP/BEP) have to be modified into proper shape. Because the flow holes' area of a flow plate affects pressure drop, the flow holes' area must be larger than/equal to that of conventional flow plates. And design criterion of the TEP/BEP says that the flow plate should withstand a 22.241 kN axial load during handling lest a calculated stress intensity should exceed the Condition I allowable stress. In this paper, newly designed flow plates of a TEP/BEP are suggested and stress analysis is conducted to evaluate strength robustness of the flow plates for the dual cooled fuel assembly

Modeling on a PWR power conversion system with system program

International Nuclear Information System (INIS)

Gao Rui; Yang Yanhua; Lin Meng

2007-01-01

Based on the power conversion system of nuclear and conventional islands of Daya Bay Power Station, this paper models the thermal-hydraulic systems of primary and secondary loops for PWR by using the PWR best-estimate program-RELAP5. To simulate the full-scope power conversion system, not only the traditional basic system models of nuclear island, but also the major system models of conventional island are all considered and modeled. A comparison between the calculated results and the actual data of reactor demonstrates a fine match for Daya Bay Nuclear Power Station, and manifests the feasibility in simulating full-scope power conversion system of PWR by RELAP5 at the same time. (authors)

Moving the largest capacity PWR dual-purpose cask in the world from Goesgen NPP to the Zwilag interim storage site

International Nuclear Information System (INIS)

Delannay, M.; Dudragne, S.

2002-01-01

The Swiss Goesgen nuclear power plant (NPP) has decided to use two different methods for the disposal of its spent fuel. (1) To reprocess some of its spent fuel in dedicated facilities. Some of the vitrified waste from the reprocessing will be shipped back to Switzerland using the new COGEMA Logistics, TN81 cask. (2) To ship the other part of its spent fuel to the central interim storage facility of Zwilag (Switzerland) using a COGEMA Logistics dual-purpose TN24G cask. The TN24G is the heaviest and largest dual-purpose cask manufactured so far by COGEMA Logistics in Europe. It is intended for the transport and storage of 37 pressurised water-reactor (PWR) spent fuel assemblies. Four casks were delivered by COGEMA Logistics to Goesgen NPP. Three transports of loaded TN24G casks between Goesgen and Zwilag were successfully performed at the beginning of 2002 with the new COGEMA Logistics Q76 wagon specifically designed to transport heavy casks. This article describes the procedure of operations and shipments for the first TN24G casks up to storage at Zwilag. The fourth transport of loaded TN24G was due to happen in October 2002. The TN24G cask, as part of the TN24 casks family, proved to be a very efficient solution for the KKG spent fuel management. (author)

On site PWR fuel inspection measurements for operational and design verification

International Nuclear Information System (INIS)

1996-01-01

The on-site inspection of irradiated Pressurized Water Reactor (PWR) fuel and Non-Fuel Bearing Components (NFBC) is typically limited to visual inspections during refuelings using underwater TV cameras and is intended primarily to confirm whether the components will continue in operation. These inspections do not normally provide data for design verification nor information to benefit future fuel designs. Japanese PWR utilities and Nuclear Fuel Industries Ltd. designed, built, and performed demonstration tests of on-site inspection equipment that confirms operational readiness of PWR fuel and NFBC and also gathers data for design verification of these components. 4 figs, 3 tabs

Behaviour of fission products in PWR primary coolant and defected fuel rods evaluation

International Nuclear Information System (INIS)

Bourgeois, P.; Stora, J.P.

1979-01-01

The activity surveillance of the PWR primary coolant by γ spectometry gives some informations on fuel failures. The activity of different nuclides e.g. Xenons, Kryptons, Iodines, can be correlated with the number of the defected fuel rods. Therefore the precharacterization with eventually a prelocalization of the related fuel assemblies direct the sipping-test and allows a saving of time during refueling. A model is proposed to calculate the number of the defected rods from the activity measurements of the primary coolant. A semi-empirical model of the release of the fission products has been built from the activity measurements of the primary coolant in a 900 MWe PWR. This model allows to calculate the number of the defected rods and also a typical parameter of the mean damage. Fission product release is described by three stages: release from uranium dioxide, transport across the gas gap and behaviour in the primary coolant. The model of release from the oxide considers a diffusion process in the grains with trapping. The release then occurs either directly to free surfaces or with a delay due to a transit into closed porosity of the oxide. The amount released is the same for iodine and rare gas. With the gas gap transit is associated a transport time and a probability of trapping for the iodines. In the primary coolant the purification and the radioactive decay are considered. (orig.)

Waste management: products and services

International Nuclear Information System (INIS)

Anon.

1992-01-01

A number of products and services related to radioactive waste management are described. These include: a portable cement solidification system for waste immobilization; spent fuel storage racks; storage and transport flasks; an on-site low-level waste storage facility; supercompactors; a mobile waste retrieval and encapsulation plant; underwater crushers; fuel assembly disposal; gaseous waste management; environmental restoration and waste management services; a waste treatment consultancy. (UK)

Pressurizer and steam-generator behavior under PWR transient conditions

International Nuclear Information System (INIS)

Wahba, A.B.; Berta, V.T.; Pointner, W.

1983-01-01

Experiments have been conducted in the Loss-of-Fluid Test (LOFT) pressurized water reactor (PWR), at the Idaho National Engineering Laboratory, in which transient phenomena arising from accident events with and without reactor scram were studied. The main purpose of the LOFT facility is to provide data for the development of computer codes for PWR transient analyses. Significant thermal-hydraulic differences have been observed between the measured and calculated results for those transients in which the pressurizer and steam generator strongly influence the dominant transient phenomena. Pressurizer and steam generator phenomena that occurred during four specific PWR transients in the LOFT facility are discussed. Two transients were accompanied by pressurizer inflow and a reduction of the heat transfer in the steam generator to a very small value. The other two transients were accompanied by pressurizer outflow while the steam generator behavior was controlled

The integrated PWR

International Nuclear Information System (INIS)

Gautier, G.M.

2002-01-01

This document presents the integrated reactors concepts by a presentation of four reactors: PIUS, SIR, IRIS and CAREM. The core conception, the operating, the safety, the economical aspects and the possible users are detailed. From the performance of the classical integrated PWR, the necessity of new innovative fuels utilization, the research of a simplified design to make easier the safety and the KWh cost decrease, a new integrated reactor is presented: SCAR 600. (A.L.B.)

Advanced ion exchange resins for PWR condensate polishing

International Nuclear Information System (INIS)

Hoffman, B.; Tsuzuki, S.

2002-01-01

The severe chemical and mechanical requirements of a pressurized water reactor (PWR) condensate polishing plant (CPP) present a major challenge to the design of ion exchange resins. This paper describes the development and initial operating experience of improved cation and anion exchange resins that were specifically designed to meet PWR CPP needs. Although this paper focuses specifically on the ion exchange resins and their role in plant performance, it is also recognized and acknowledged that excellent mechanical design and operation of the CPP system are equally essential to obtaining good results. (authors)

Two optimal control methods for PWR core control

International Nuclear Information System (INIS)

Karppinen, J.; Blomsnes, B.; Versluis, R.M.

1976-01-01

The Multistage Mathematical Programming (MMP) and State Variable Feedback (SVF) methods for PWR core control are presented in this paper. The MMP method is primarily intended for optimization of the core behaviour with respect to xenon induced power distribution effects in load cycle operation. The SVF method is most suited for xenon oscillation damping in situations where the core load is unpredictable or expected to stay constant. Results from simulation studies in which the two methods have been applied for control of simple PWR core models are presented. (orig./RW) [de

Transient performance of flow in PWR reactor circuits

International Nuclear Information System (INIS)

Hirdes, V.R.T.R.; Carajilescov, P.

1988-12-01

Generally, PWR's are designed with several primary loops, each one provided with a pump to circulate the coolant through the core. If one or more of these pumps fail, there would be a decrease in reactor flow rate which cause coolant phase change in the core and components overheating. The present work establishes a simulation model for pump failure in PWR's and the SARDAN-FLOW computes code was developed, considering any combination of such failures. Based on the data of Angra I, several accident and operational transient conditions were simulated. (author) [pt

Redesigning assembly stations using ergonomic methods as a lean tool.

Science.gov (United States)

Eswaramoorthi, M; John, Mervyn; Rajagopal, C Arjun; Prasad, P S S; Mohanram, P V

2010-01-01

With the current state of the global economy, demand for various products plummeting. To sustain in the market, companies have to reduce cost and improve quality. Today, companies have started implementing new philosophies like TQM, TPM, six sigma and lean manufacturing techniques to remain competitive in the market. Lean manufacturing is an emerging philosophy which continuously strives to reduce waste. The main objective of analyzing the assembly line with a lean perspective is to identify the areas related to human interface with other systems that could lead to the generation of waste. Improper workplace design leads to unreasonable mental or physical burden and results in waste generation like slow work (delay and inventory), and defects, which is named as muri waste. An attempt has been made in this paper to locate muri waste and create a "Lean assembly line". The proposed method, based on the use of Rapid Upper Limb Assessment (RULA) with CATIA V5 platform, has allowed the measurement of a large set of operator posture parameters and assessment of ergonomic stresses. Based on the results, the process stations in the assembly line were redesigned to prevent the generation of waste.

Babcock and Wilcox advanced PWR development

International Nuclear Information System (INIS)

Kulynych, G.E.; Lemon, J.E.

1986-01-01

The Babcock and Wilcox 600 MWe PWR design is discussed. Main features of the new B-600 design are improvements in reactor system configuration, glandless coolant pumps, safety features, core design and steam generators

Overweight truck shipments to nuclear waste repositories: legal, political, administrative and operational considerations

International Nuclear Information System (INIS)

1986-03-01

This report, prepared for the Chicago Operations Office and the Office of Civilian Radioactive Waste Management (OCRWM) of the US Department of Energy (DOE), identifies and analyzes legal, political, administrative, and operational issues that could affect an OCRWM decision to develop an overweight truck cask fleet for the commercial nuclear waste repository program. It also provides information required by DOE on vehicle size-and-weight administration and regulation, pertinent to nuclear waste shipments. Current legal-weight truck casks have a payload of one pressurized-water reactor spent fuel element or two boiling-water reactor spent fuel elements (1 PWR/2 BWR). For the requirements of the 1960s and 1970s, casks were designed with massive shielding to accommodate 6-month-old spent fuel; the gross vehicle weight was limited to 73,280 pounds. Spent fuel to be moved in the 1990s will have aged five years or more. Gross vehicle weight limitation for the Interstate highway system has been increased to 80,000 pounds. These changes allow the design of 25-ton legal-weight truck casks with payloads of 2 PWR/5 BWR. These changes may also allow the development of a 40-ton overweight truck cask with a payload of 4 PWR/10 BWR. Such overweight casks will result in significantly fewer highway shipments compared with legal-weight casks, with potential reductions in transport-related repository risks and costs. These advantages must be weighed against a number of institutional issues surrounding such overweight shipments before a substantial commitment is made to develop an overweight truck cask fleet. This report discusses these issues in detail and provides recommended actions to DOE

RSK-guidelines for PWR reactors

International Nuclear Information System (INIS)

1979-01-01

The RSK guidelines for PWA reactors of April 24, 1974, have been revised and amended in this edition. The RSK presents a summary of safety requirements to be observed in the design, construction, and operation of PWR reactors in the form of guidelines. From January 1979 onwards these guidelines will be the basis of siting and safety considerations for new PWR reactors, and newly built nuclear power plants will have to form these guidelines. They are not binding for existing nuclear power plants under construction or in operation. It will be a matter of individual discussion whether or not the guidelines will be applied in these plants. The main purpose of the guidelines is to facilitate discussion among RSK members and to give early information on necessary safety requirements. If the guidelines are observed by producers and operators, the RSK will make statements on individual projects at short notice. (orig./HP) [de

Fuel management optimization for a PWR

International Nuclear Information System (INIS)

Dumas, M.; Robeau, D.

1981-04-01

This study is aimed to optimize the refueling pattern of a PWR. Two methods are developed, they are based on a linearized form of the optimization problem. The first method determines a feasible solution in two steps; in the first one the original problem is replaced by a relaxed one which is solved by the Method of Approximation Programming. The second step is based on the Branch and Bound method to find the feasible solution closest to the solution obtained in the first step. The second method starts from a given refueling pattern and tries to improve this pattern by the calculation of the effects of 2 by 2, 3 by 3 and 4 by 4 permutations on the objective function. Numerical results are given for a typical PWR refueling using the two methods

Dilute chemical decontamination resins and the mixed waste issue

International Nuclear Information System (INIS)

Denault, R.P.; Hallman, J.T.

1988-01-01

The decontamination of reactor primary systems, sub-systems and components is an important method used to reduce the occupational radiation exposure of nuclear plant personnel. The waste produced by the application of this technology is mainly solid in the form of ion exchange resins. As a result of a recent agreement between the Environmental Protection Agency (EPA) and the Nuclear Regulatory Commission (NRC), all radioactive waste must meet EPA burial criteria. The chemicals used in a decontamination and certain metals dissolved during the process, primarily chromium, could render the waste hazardous as well as radioactive or more commonly called a mixed waste. This paper defines mixed waste as described in the EPA directive 9432.00-2, and examine the criteria by which waste is categorized as hazardous. The decontamination waste resin generated by two processes, the CAN-DEREM and the LOMI process, is described in detail. Waste data obtained from decontaminations performed by LN Technologies Corporation including chemical, metal and radionuclide loadings on resins from both PWR and BWR applications are presented

Decruding of PWR Fuel with the ICEDEC{sup TM} technique

Energy Technology Data Exchange (ETDEWEB)

Ivars, Roland; Fredriksson, Eva; Rosengren, Anders; Hallgren, Peter [Westinghouse Atom AB, Uppsala (Sweden)

2002-04-15

The novel fuel decontamination system ICEDEC{sup TM} utilizes a mixture of ice particles and water circulating through the assembly for scraping off loose crud from the fuel surfaces. Initially, ICEDEC{sup TM} was developed for BWRs. By means of fuel decontamination the origin of the personnel radiation exposure, i. e. the loose fuel crud, can be decreased. The technique can be used for radiation level reduction, eliminating the AOA (Axial Offset anomaly) problem or general decruding purposes. Decontamination tests of burned out and two-year-old fuel in the BWR Ringhals 1 in Sweden verified that ICEDEC{sup TM} maintained the mechanical integrity of the fuel and fulfilled the very important criteria; only the loose crud was removed and the oxide layer was not affected. Activity measurements prior to and after the decontamination, showed that more than 50% of the loose crud was removed from the fuel surfaces. For PWR the condition of maintained boron level in the pool water is a prerequisite. This can be achieved by utilizing a closed loop system with a water reservoir. From the reservoir water is used for the production of the ice particles. After removal of the loose crud from the fuel the crud/ice/water slurry is separated in a specially designed filter unit. The melted ice and residual water is then transported back to the water reservoir. Other methods could be to add boron equivalent to the excess water from the melted ice or use reverse osmosis to separate the boron and water in the pool. Including an application study followed by preliminary and detailed designs and manufacture and testing a PWR ICEDEC{sup TM} system can be licensed after two years.

Burning Plutonium and minimizing the radioactive waste in existing PWR

International Nuclear Information System (INIS)

Mittag, S.; Kliem, S.

2009-01-01

Long-lived radioactive actinides are produced in light water reactors (LWR) using conventional fuel. 'Innovative' fuel matrices may reduce the breeding of these nuclides. However, inherent LWR safety features have to be preserved, which restricts the possibilities for new fuel-carrying matrices. Respective fuel-assembly and LWR-core safety studies indicate practicable new fuel options for the near future. (authors)

Burning plutonium and minimizing the radioactive waste in existing PWR

International Nuclear Information System (INIS)

Mittag, S.; Kliem, S.

2009-01-01

Long-lived radioactive actinides are produced in light water reactor (LWR) using conventional fuel. 'Innovative' fuel matrices may reduce the breeding of these nuclides. However, inherent LWR safety features have to be preserved, which restricts the possibilities for new fuel-carrying matrices. Respective fuel-assembly and LWR-core safety studies indicate practicable new fuel options for the near future. (Authors)

EPRI PWR primary water chemistry guidelines revision

International Nuclear Information System (INIS)

McElrath, Joel; Fruzzetti, Keith

2014-01-01

EPRI periodically updates the PWR Primary Water Chemistry Guidelines as new information becomes available and as required by NEI 97-06 (Steam Generator Program Guidelines) and NEI 03-08 (Guideline for the Management of Materials Issues). The last revision of the PWR water chemistry guidelines identified an optimum primary water chemistry program based on then-current understanding of research and field information. This new revision provides further details with regard to primary water stress corrosion cracking (PWSCC), fuel integrity, and shutdown dose rates. A committee of industry experts, including utility specialists, nuclear steam supply system (NSSS) and fuel vendor representatives, Institute of Nuclear Power Operations (INPO) representatives, consultants, and EPRI staff collaborated in reviewing the available data on primary water chemistry, reactor water coolant system materials issues, fuel integrity and performance issues, and radiation dose rate issues. From the data, the committee updated the water chemistry guidelines that all PWR nuclear plants should adopt. The committee revised guidance with regard to optimization to reflect industry experience gained since the publication of Revision 6. Among the changes, the technical information regarding the impact of zinc injection on PWSCC initiation and dose rate reduction has been updated to reflect the current level of knowledge within the industry. Similarly, industry experience with elevated lithium concentrations with regard to fuel performance and radiation dose rates has been updated to reflect data collected to date. Recognizing that each nuclear plant owner has a unique set of design, operating, and corporate concerns, the guidelines committee has retained a method for plant-specific optimization. Revision 7 of the Pressurized Water Reactor Primary Water Chemistry Guidelines provides guidance for PWR primary systems of all manufacture and design. The guidelines continue to emphasize plant

A comparison of fuzzy logic-PID control strategies for PWR pressurizer control

International Nuclear Information System (INIS)

Kavaklioglu, K.; Ikonomopoulos, A.

1993-01-01

This paper describes the results obtained from a comparison performed between classical proportional-integral-derivative (PID) and fuzzy logic (FL) controlling the pressure in a pressurized water reactor (PWR). The two methodologies have been tested under various transient scenarios, and their performances are evaluated with respect to robustness and on-time response to external stimuli. One of the main concerns in the safe operation of PWR is the pressure control in the primary side of the system. In order to maintain the pressure in a PWR at the desired level, the pressurizer component equipped with sprayers, heaters, and safety relief valves is used. The control strategy in a Westinghouse PWR is implemented with a PID controller that initiates either the electric heaters or the sprayers, depending on the direction of the coolant pressure deviation from the setpoint

Embedding of radioactive wastes by thermosetting resins

International Nuclear Information System (INIS)

Baer, A.; Traxler, A.; Limongi, A.; Thiery, D.

The process for embedding radioactive wastes in thermosetting resins perfected and applied at the Grenoble Nuclear Research Center and its application to the treatment of radioactive wastes from Light-Water Nuclear Power Plants (PWR and BWR) are presented. The various types of wastes are enumerated and their activities and quantities are estimated: evaporator concentrates, ion exchange resins, filtration sludges, filters, various solid wastes, etc. The authors review the orientations of the research performed and indicate, for each type of waste considered, the cycle of treatment operations from rendering the radioelements insoluble to drying the concentrates to final embedding. The operational safety of the process and the safety of transport and storage of the embedded wastes are investigated. The essential technical features concerning the safety of the installation and of the final product obtained are presented. In particular, results are presented from tests of resistance to fire, irradiation, leaching, etc., these being characteristics which represent safety criteria. The economic aspects of the process are considered by presenting the influences of the reduction of volume and weight of wastes to be stored, simplicity of installations and cost of primary materials

Conceptual design of simplified PWR

International Nuclear Information System (INIS)

Tabata, Hiroaki

1996-01-01

The limited availability for location of nuclear power plant in Japan makes plants with higher power ratings more desirable. Having no intention of constructing medium-sized plants as a next generation standard plant, Japanese utilities are interested in applying passive technologies to large ones. So, Japanese utilities have studied large passive plants based on AP600 and SBWR as alternative future LWRs. In a joint effort to develop a new generation nuclear power plant which is more friendly to operator and maintenance personnel and is economically competitive with alternative sources of power generation, JAPC and Japanese Utilities started the study to modify AP600 and SBWR, in order to accommodate the Japanese requirements. During a six year program up to 1994, basic concepts for 1000 MWe class Simplified PWR (SPWR) and Simplified BWR (SBWR) were developed, though there still remain several areas to be improved. These studies have now stepped into the phase of reducing construction cost and searching for maximum power rating that can be attained by reasonably practical technology. These results also suggest that it is hopeful to develop a large 3-loop passive plant (∼1200 MWe). Since Korea mainly deals with PWR, this paper summarizes SPWR study. The SPWR is jointly studied by JAPC, Japanese PWR Utilities, EdF, WH and Mitsubishi Heavy Industry. Using the AP-600 reference design as a basis, we enlarged the plant size to 3-loops and added engineering features to conform with Japanese practice and Utilities' preference. The SPWR program definitively confirmed the feasibility of a passive plant with an NSSS rating about 1000 MWe and 3 loops. (J.P.N.)

Development of bitumization plant of radioactive waste

International Nuclear Information System (INIS)

Lee, S.H.; Chun, K.S.; Song, H.Y.; Park, S.H.; Park, W.J.; Ryoo, R.; Cho, W.J.; Wee, K.S.; Lee, J.D.

1981-01-01

This study is to develop the bitumization techniques of radioactive waste concentrates from nuclear power plants (PWR), Cold-run and hot-run bitumization pilot plant were designed and constructed, and testing was carried out. The results show that the range of pH 7 to 8, in which a soluble product could form, is suitable for feeding in the waste and for its incorporation into asphalt, domestic blown asphalt is suitable up to an exposure of 10 8 rad. The estimated viscosity of the asphalt/waste product is about 14 poises at 175 0 C and the asphalt/wastes products in simulated sea-water for three weeks showed no evidence of swelling. The leaching rate from the spent resin/asphalt products in distilled water less than 1/1000 of that from the cement-products. It is considered that the resin content which is suitable for the incorporation of spent resin into asphalt is less than 50 wt%

RCC-M - Design and Conception Rules for Mechanical Components of PWR Nuclear Islands

International Nuclear Information System (INIS)

2007-01-01

The design and construction rules applicable to mechanical components of PWR Nuclear Islands (RCC-M) are a part of the collection of design and construction rules for nuclear power plants. It covers the rules applicable to the design and manufacture of pressure boundaries of mechanical equipment of pressurized water reactors (PWR). The pressure components subject to the RCC-M are specified in A 4000. They include the reactor fluid systems (primary, secondary and auxiliary systems) and other components which are not subject to pressure: vessel internals, supports for pressure components subject to the RCC-M, nuclear island storage tanks. When a pressure equipment is subject to the RCC-M, all its elements subject to pressure are also, in accordance with the provisions of A 4000, and these elements are the same class as the component. In this case all the provisions of the RCC-M are applicable: design, procurement, manufacture, inspection and pressure testing. Elements which are not subject to pressure and which are subject to the RCC-M may be covered within the Code by limited specific provisions (procurement of materials for example). The other rules applicable to this equipment must be in contractual form. The assemblies comprising pressure equipment assembled by a manufacturer to constitute an integrated and functional whole, shall be subject to the rules indicated in this Code. Main objectives of Code Requirements are to ensure the integrity and mechanical stability over the equipment design life. Function ability and operability of equipment are not directly addressed in the Code. The RCC-M contributes to ensuring compliance with regulatory requirements. These requirements depend on the applicable regulatory context. The RCC-M is representative of the state of the art as concerns the design and manufacture of PWR components, ensuring an overall safety level tested through experience. The RCC-M consists of five sections, which provide rules for the design and

Assessment of subcriticality during PWR-type reactor refueling; Evaluation de la sous-criticite lors des operations de chargement d'un reacteur nucleaire REP

Energy Technology Data Exchange (ETDEWEB)

Verdier, A

2005-04-15

During the core loading period of a PWR, any fuel assembly misplacements may significantly reduce the existing criticality margin. The Dampierre 4-18 event showed the present monitoring based on the variations of the outside-core detector counting rate cannot detect such misplacements. In order to circumvent that, a more detailed analysis of the available signal was done. We particularly focused on the neutronic noise analysis methods such as MSM (modified source multiplication), MSA (amplified source multiplication), Rossi-{alpha} and Feynman-{alpha} methods. The experimental part of our work was dedicated to the application of those methods to a research reactor. Finally, our results showed that those methods cannot be used with the present PWR instrumentation. Various detector positions were then studied using Monte Carlo calculations capable of following the neutron origin. Our results showed that the present technology does not allow us to use any solution based on neutron detection for monitoring core loading. (author)

Safeguards on MOX assemblies at LWRs

International Nuclear Information System (INIS)

Arenas Carrasco, J.; Koulikov, I.; Heinonen, O.J.; Arlt, R.; Grigoleit, K.; Clarke, R.; Swinhoe, M.

2000-01-01

Operating within the framework of the New Partnership Approach (NPA) for unirradiated MOX fuel assemblies in LWRs, the IAEA and EURATOM have gained experience in safeguarding 13 LWRs licensed to operate with MOX assemblies. In order to fulfil SIR requirements, verification methods and techniques capable of measuring MOX assemblies under water have been and are still being developed. These encompass both qualitative tests for the detection of plutonium (gross attribute tests) and quantitative tests for the measurement of the amount of plutonium (partial defect tests) and are based on gamma and neutron detection techniques. There are nine PWR and two BWR where the reactor and the spent fuel pond can be covered by the same surveillance device. These are Type I reactors where the reactor and the pond are located in the same hall. In these types of facilities relying on surveillance during the MOX refuelling is especially difficult at the BWRs due to the depth of the core pond. There are two PWR type facilities where the reactor and the spent fuel pond are located in different halls and cannot be covered by the same surveillance device (Type II). An open core camera has not been installed during refuelling and therefore indirect surveillance is currently used to survey MOX loading. Improvements are therefore required and are under consideration. After receipt at the facility, there are a few facilities which must keep the received fresh MOX fuel in wet storage, not only for a short period prior to refuelling, but for more than a year, until the next refuelling campaign. In these cases timely inspections for direct use fresh nuclear material require considerable inspection effort. Additionally, where human surveillance of core loading and finally core closure are necessary there is also a large demand for manpower. Either an agreement should be reached with the operators to delay the MOX loading until the end of the fuelling campaign, or alternative approaches should be

Waste minimization successes at McGuire Nuclear Station

International Nuclear Information System (INIS)

Correll, J.C.; Johnson, G.T.

1995-01-01

McGuire Nuclear Station is a two unit, 1125 MWe PWR located 25 miles north of Charlotte, North Carolina. It is a Westinghouse Ice Condenser plant that is owned and operated by Duke Power Company. At Duke Power, open-quotes Culture Changeclose quotes is a common term that we have used to describe the incredible transformation that we are making to become a cost conscious, customer driven, highly competitive business. Nowhere has this change been more evident then in the way we process and disposed of our solid radioactive waste. With top-down management support, we have used team-based, formalized, problem solving methods and have implemented many successful waste minimization programs. Through these programs, we have dramatically increased employees close-quote awareness of the importance of waste minimization. As a result, we have been able to reduce both our burial volumes and our waste processing and disposal costs

Fuel-assembly vibration-induced neutron noise in PWRs

International Nuclear Information System (INIS)

Sweeney, F.J.; Renier, J.P.

1983-01-01

Space-dependent reactor kinetics calculations were performed to interpret observed increases in the amplitude of pressurized water reactor (PWR), ex-core neutron detector noise with increasing fuel burnup and correspondingly decreasing soluble boron concentration. These noise amplitude increases have occurred at both low frequencies (< 1.0 Hz) and in the 2.0- to 4.0-Hz frequency range. The noise amplitude increases in the 2.0- to 4.0-Hz frequency range have usually been accompanied by a decrease in the fundamental mode fuel assembly resonant frequency from 3.5 to 2.5 Hz over a fuel cycle, which has also been attributed to grid spacer spring relaxation

Generation of consistent nuclear properties of DUPIC fuel by DRAGON with ENDF/B-VI nuclear data library

International Nuclear Information System (INIS)

Shen, W.; Rozon, D.

1998-01-01

DRAGON code with 89-groups ENDF/B-VI cross section library was used in this paper to generate consistent nuclear properties of DUPIC fuel. The reference feed material used for the DUPIC fuel cycle is a 17x17 French standard 900 MWe PWR spent fuel assembly with 3.2 w/o initial enrichment and 32500 MWD/7 discharge burnup. The PWR fuel assembly was modeled by JPMT/SYBILT transport method in DRAGON to generate nuclide fields of spent PWR fuel. The resultant nuclide fields constitute the initial fuel composition files for reference DUPIC fuel which can be accessed by DRAGON for CANDU 2D cluster geometry depletion calculation and 3D supercell calculation. Because of uneven spatial power distribution in PWR assemblies and full core, unexpected transition cycle, and various fuel management strategy, the spent PWR fuel composition is expected to be different from one assembly to the next. This heterogeneity was characterized also by modeling various spent PWR fuel assembly types in the paper. (author)

Validation of full core geometry model of the NODAL3 code in the PWR transient Benchmark problems

International Nuclear Information System (INIS)

T-M Sembiring; S-Pinem; P-H Liem

2015-01-01

The coupled neutronic and thermal-hydraulic (T/H) code, NODAL3 code, has been validated in some PWR static benchmark and the NEACRP PWR transient benchmark cases. However, the NODAL3 code have not yet validated in the transient benchmark cases of a control rod assembly (CR) ejection at peripheral core using a full core geometry model, the C1 and C2 cases. By this research work, the accuracy of the NODAL3 code for one CR ejection or the unsymmetrical group of CRs ejection case can be validated. The calculations by the NODAL3 code have been carried out by the adiabatic method (AM) and the improved quasistatic method (IQS). All calculated transient parameters by the NODAL3 code were compared with the reference results by the PANTHER code. The maximum relative difference of 16 % occurs in the calculated time of power maximum parameter by using the IQS method, while the relative difference of the AM method is 4 % for C2 case. All calculation results by the NODAL3 code shows there is no systematic difference, it means the neutronic and T/H modules are adopted in the code are considered correct. Therefore, all calculation results by using the NODAL3 code are very good agreement with the reference results. (author)

The latest full-scale PWR simulator in Japan

International Nuclear Information System (INIS)

Nishimuru, Y.; Tagi, H.; Nakabayashi, T.

2004-01-01

The latest MHI Full-scale Simulator has an excellent system configuration, in both flexibility and extendability, and has highly sophisticated performance in PWR simulation by the adoption of CANAC-II and PRETTY codes. It also has an instructive character to display the plant's internal status, such as RCS condition, through animation. Further, the simulation has been verified to meet a functional examination at model plant, and with a scale model test result in a two-phase flow event, after evaluation for its accuracy. Thus, the Simulator can be devoted to a sophisticated and broad training course on PWR operation. (author)

PHEDRE model for the simulation of PWR reactors

International Nuclear Information System (INIS)

Bernard, Patrice; Dupraz, Remy; Vasile, Alfredo.

1979-11-01

This note presents the model of PHEDRE, simulator of a PWR, set on the hybrid computers of CISI, at the Nuclear Research Center of Cadarache. The model mainly concerns the primary part and the steam production of the PWR constructed in France. It includes an axial modelization of the core, the pressurizer, two loops of steam production and the inlet of the turbine, and the regulations concerning these components. The note presents the equations of the model, the structures of the codes concerning the initialization and the dynamic resolution, and describes the control panel of PHEDRE [fr

Model for transient simulation in a PWR steam circuit

International Nuclear Information System (INIS)

Mello, L.A. de.

1982-11-01

A computer code (SURF) was developed and used to simulate pressure losses along the tubes of the main steam circuit of a PWR nuclear power plant, and the steam flow through relief and safety valves when pressure reactors its thresholds values. A thermodynamic model of turbines (high and low pressure), and its associated components are simulated too. The SURF computer code was coupled to the GEVAP computer code, complementing the simulation of a PWR nuclear power plant main steam circuit. (Author) [pt

GO evaluation of a PWR spray system. Final report

International Nuclear Information System (INIS)

Long, W.T.

1975-08-01

GO is a reliability analysis methodology developed over the years from 1960 to the present by Kaman Sciences Corporation, Colorado Springs, Colorado. In this report the GO methodology is presented and its application demonstrated by performing a reliability analysis of a conceptual PWR Containment Spray System. Certain numerical results obtained are compared with those of a prior fault tree analysis of the same system as documented in the 11 January 1973 draft report, A Fault Tree Evaluation of a PWR Spray System

Radionuclide release from PWR fuels in a reference tuff repository groundwater

International Nuclear Information System (INIS)

Wilson, C.N.; Oversby, V.M.

1985-03-01

The Nevada Nuclear Waste Storage Investigations Project (NNWSI) is studying the suitability of the welded devitrified Topopah Spring tuff at Yucca Mountain, Nye County, Nevada, for potential use as a high-level nuclear waste repository. In support of the Waste Package task of NNWSI, tests have been conducted under ambient air environment to measure radionuclide release from two pressurized water reactor (PWR) spent fuels in water obtained from the J-13 well near the Yucca Mountain site. Four specimen types, representing a range of fuel physical conditions that may exist in a failed waste canister containing a limited amount of water were tested. The specimen types were: fuel rod sections split open to expose bare fuel particles; rod sections with water-tight end fittings with a 2.5-cm long by 150-μm wide slit through the cladding; rod sections with water-tight end fittings and two 200-μm-diameter holes through the cladding; and undefected rod segments with water-tight end fittings. Radionuclide release results from the first 223-day test runs on H.B. Robinson spent fuel specimens in J-13 water are reported and compared to results from a previous test series in which similar Turkey Point reactor spent fuel specimens were tested on deionized water. Selected initial results are also given for Turkey Point fuel specimens tested on J-13 water. Results suggest that the actinides Pu, Am, Cm and Np are released congruently with U as the UO 2 spent fuel matrix dissolves. Fractional release of 137 Cs and 99 Tc was greater than that measured for the actinides. Generally, lower radionuclide releases were measured for the H.B. Robinson fuel in J-13 water than for Turkey Point Fuel in deionized water. 8 references, 7 figures, 9 tables

A preliminary evaluation of the ability of from-reactor casks to geometrically accommodate commercial LWR spent nuclear fuel

International Nuclear Information System (INIS)

Andress, D.; Joy, D.S.; McLeod, N.B.; Peterson, R.W.; Rahimi, M.

1991-01-01

The Department of Energy has sponsored a number of cask design efforts to define several transportation casks to accommodate the various assemblies expected to be accepted by the Federal Waste Management System. At this time, three preliminary cask designs have been selected for the final design--the GA-4 and GA-9 truck casks and the BR-100 rail cask. In total, this assessment indicates that the current Initiative I cask designs can be expected to dimensionally accommodate 100% of the PWR fuel assemblies (other than the extra-long South Texas Fuel) with control elements removed, and >90% of the assemblies having the control elements as an integral part of the fuel assembly. For BWR assemblies, >99% of the assemblies can be accommodated with fuel channels removed. This paper summarizes preliminary results of one part of that evaluation related to the ability of the From-Reactor Initiative I casks to accommodate the physical and radiological characteristics of the Spent Nuclear Fuel projected to be accepted into the Federal Waste Management System. 3 refs., 5 tabs

In-Core Fuel Managements for PWRs: Investigation on solution for optimal utilization of PWR fuel through the use of fuel assemblies with differently enriched {sup 235}U fuel pins

Energy Technology Data Exchange (ETDEWEB)

Caprioli, Sara

2004-04-01

A possibility for more efficient use of the nuclear fuel in a pressurized water reactor is investigated. The alternative proposed here consists of the implementation of PWR fuel assemblies with differently enriched {sup 235}U fuel pins. This possibility is examined in comparison with the standard assembly design. The comparison is performed both in terms of single assembly performance and in the terms of nuclear reactor core performance and fuel utility. For the evaluation of the actual performance of the new assembly types, 5 operated fuel core sequences of R3 (Ringhals' third unit), for the period 1999 - 2004 (cycles 17 - 21) were examined. For every cycle, the standard fresh fuel assemblies have been identified and taken as reference cases for the study of the new type of assemblies with differently enriched uranium rods. In every cycle, assemblies with and without burnable absorber are freshly loaded into the core. The axial enrichment distribution is kept uniform, allowing for a radial (planar) enrichment level distribution only. At an assembly level, it has been observed that the implementation of the alternative enrichment configuration can lead to lower and flatter internal peaking factor distribution with respect to the uniformly enriched reference assemblies. This can be achieved by limiting the enrichment levels distribution to a rather narrow range. The highest enrichment level chosen has the greatest impact on the power distribution of the assemblies. As it increases, the enrichment level drives the internal peaking factor to greater values than in the reference assemblies. Generally, the highest enrichment level that would allow an improvement in the power performance of the assembly lies between 3.95 w/o and 4.17 w/o. The highest possible enrichment level depends on the average enrichment of the overall assembly, which is kept constant to the average enrichment of the reference assemblies. The improvements that can be obtained at this level are

Economic analysis of a volume reduction/polyethylene solidification system for low-level radioactive wastes

International Nuclear Information System (INIS)

Kalb, P.D.; Colombo, P.

1985-01-01

A study was conducted at Brookhaven National Laboratory to determine the economic feasibility of a fluidized bed volume reduction/polyethylene solidification system for low-level radioactive wastes. These results are compared with the ''null'' alternative of no volume reduction and solidification of aqueous waste streams in hydraulic cement. The economic analysis employed a levelized revenue requirement (LRR) technique conducted over a ten year period. An interactive computer program was written to conduct the LRR calculations. Both of the treatment/solidification options were considered for a number of scenarios including type of plant (BWR or PWR) and transportation distance to the disposal site. If current trends in the escalation rates of cost components continue, the volume reduction/polyethylene solidification option will be cost effective for both BWRs and PWRs. Data indicate that a minimum net annual savings of $0.8 million per year (for a PWR shipping its waste 750 miles) and a maximum net annual savings of $9 million per year (for a BWR shipping its waste 2500 miles) can be achieved. A sensitivity analysis was performed for the burial cost escalation rate, which indicated that variation of this factor will impact the total levelized revenue requirement. The burial cost escalation rate which yields a break-even condition was determined for each scenario considered. 11 refs., 8 figs., 39 tabs

Assessment of PWR Steam Generator modelling in RELAP5/MOD2

International Nuclear Information System (INIS)

Putney, J.M.; Preece, R.J.

1993-06-01

An assessment of Steam Generator (SG) modelling in the PWR thermal-hydraulic code RELAP5/MOD2 is presented. The assessment is based on a review of code assessment calculations performed in the UK and elsewhere, detailed calculations against a series of commissioning tests carried out on the Wolf Creek PWR and analytical investigations of the phenomena involved in normal and abnormal SG operation. A number of modelling deficiencies are identified and their implications for PWR safety analysis are discussed -- including methods for compensating for the deficiencies through changes to the input deck. Consideration is also given as to whether the deficiencies will still be present in the successor code RELAP5/MOD3

Calculational modeling of fuel assemblies of WWER-1000 type with the use of burnable absorber Gadolinum; comparative analysis

International Nuclear Information System (INIS)

Yeremenko, M.L.; Kovbasenko, Yu.P.; Loetsch, T.

2001-01-01

In connection with the beginning of the use of fuel assemblies with burnable absorbers by integration of Gadolinum into the nuclear fuel at Ukrainian NPP the task of testing the code systems and the pertinent neutron cross section libraries for the new fuel arose. Taking into account the long term experience of German experts with calculations and evaluation of nuclear fuel containing Gadolinum it was decided to carry out a series of test calculations for fuel assembly lattices of PWR, WWER-440 and WWER-1000 types using the NESSEL/PYTHIA and CASMO/SIMULATE code systems (Authors)

SCFR Fuel Cycles and Their Impact on the Performance of High-Level Waste Disposal

Energy Technology Data Exchange (ETDEWEB)

Kawasaki, Daisuke; Nogi, Naoyuki; Saito, Takumi [Department of Nuclear Engineering and Management, Graduate School of Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo, 113-8656 (Japan); Nagasaki, Shinya [Nuclear Professional School, Graduate School of Engineering, The University of Tokyo, 2-22 Shirakata Shirane, Tokai, Ibaraki, 319-1188 (Japan)

2009-06-15

The concept of supercritical-pressure light water cooled fast reactor (SCFR) is developed and studied at the University of Tokyo. The impact of disposal of the waste generated in a fuel cycle with SCFR is also investigated in the project. It is of great interest how a fuel cycle with SCFR compares to the other fuel cycles from the back-end view point. With its various neutron spectrum, SCFR may be used to transmute both actinides and fission products. The objective of the present study is to evaluate and compare multiple fuel cycle designs in order to investigate the effects of SCFR and its transmutation capability upon the back-end risks. Three designs of fuel cycle are considered for evaluation in the present study. First, a simple fuel cycle with PWR and recycling is considered. The spent fuel from the PWR is reprocessed to recover uranium and plutonium, and the rest of the radioactive nuclides are vitrified and disposed of in a geologic repository. In the second design, the recovered uranium and plutonium in the reprocessing of PWR spent fuel is fabricated into a MOX fuel and irradiated in SCFR. The spent fuel from the SCFR is reprocessed to recover uranium and plutonium. In the third design, actinide elements are also separated from the PWR spent fuel and is loaded as the blanket fuel in SCFR core together with the MOX fuel fabricated from the recovered uranium and plutonium. In the same way as in the second design, the spent fuel from the SCFR is reprocessed to recover uranium and plutonium. In the second and the third designs, there are two streams of highly radioactive waste; one from the reprocessing (separation process) of the PWR spent fuel, and the other from the reprocessing of the SCFR spent fuel. Numerical codes Origen2.1 and SWAT is used for fuel irradiation calculation. The performance of the high-level radioactive waste repository is evaluated for each design of fuel cycle. It is assumed that the repository is located in a water-saturated geologic

VALIDATION OF SIMBAT-PWR USING STANDARD CODE OF COBRA-EN ON REACTOR TRANSIENT CONDITION

Directory of Open Access Journals (Sweden)

Muhammad Darwis Isnaini

2016-03-01

Full Text Available The validation of Pressurized Water Reactor typed Nuclear Power Plant simulator developed by BATAN (SIMBAT-PWR using standard code of COBRA-EN on reactor transient condition has been done. The development of SIMBAT-PWR has accomplished several neutronics and thermal-hydraulic calculation modules. Therefore, the validation of the simulator is needed, especially in transient reactor operation condition. The research purpose is for characterizing the thermal-hydraulic parameters of PWR1000 core, which be able to be applied or as a comparison in developing the SIMBAT-PWR. The validation involves the calculation of the thermal-hydraulic parameters using COBRA-EN code. Furthermore, the calculation schemes are based on COBRA-EN with fixed material properties and dynamic properties that calculated by MATPRO subroutine (COBRA-EN+MATPRO for reactor condition of startup, power rise and power fluctuation from nominal to over power. The comparison of the temperature distribution at nominal 100% power shows that the fuel centerline temperature calculated by SIMBAT-PWR has 8.76% higher result than COBRA-EN result and 7.70% lower result than COBRA-EN+MATPRO. In general, SIMBAT-PWR calculation results on fuel temperature distribution are mostly between COBRA-EN and COBRA-EN+MATPRO results. The deviations of the fuel centerline, fuel surface, inner and outer cladding as well as coolant bulk temperature in the SIMBAT-PWR and the COBRA-EN calculation, are due to the value difference of the gap heat transfer coefficient and the cladding thermal conductivity.

FFTF radioactive solid waste handling and transport

International Nuclear Information System (INIS)

Thomson, J.D.

1982-01-01

The equipment necessary for the disposal of radioactive solid waste from the Fast Flux Test Facility (FFTF) is scheduled to be available for operation in late 1982. The plan for disposal of radioactive waste from FFTF will utilize special waste containers, a reusable Solid Waste Cask (SWC) and a Disposable Solid Waste Cask (DSWC). The SWC will be used to transport the waste from the Reactor Containment Building to a concrete and steel DSWC. The DSWC will then be transported to a burial site on the Hanford Reservation near Richland, Washington. Radioactive solid waste generated during the operation of the FFTF consists of activated test assembly hardware, reflectors, in-core shim assemblies and control rods. This radioactive waste must be cleaned (sodium removed) prior to disposal. This paper provides a description of the solid waste disposal process, and the casks and equipment used for handling and transport

Plutonium recycling in PWR

International Nuclear Information System (INIS)

Youinou, G.; Girieud, R.; Guigon, B.

2000-01-01

Two concepts of 100% MOX PWR cores are presented. They are designed such as to minimize the consequences of the introduction of Pu on the core control. The first one has a high moderation ratio and the second one utilizes an enriched uranium support. The important design parameters as well as their capabilities to multi recycle Pu are discussed. We conclude with the potential interest of the two concepts. (author)

Partial Defect Verification of Spent Fuel Assemblies by PDET: Principle and Field Testing in Interim Spent Fuel Storage Facility (CLAB) in Sweden

Energy Technology Data Exchange (ETDEWEB)

Ham, Y.S.; Kerr, P.; Sitaraman, S.; Swan, R. [Global Security Directorate, Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States); Rossa, R. [SCK-CEN, Mol (Belgium); Liljenfeldt, H. [SKB in Oskarshamn (Sweden)

2015-07-01

The need for the development of a credible method and instrument for partial defect verification of spent fuel has been emphasized over a few decades in the safeguards communities as the diverted spent fuel pins can be the source of nuclear terrorism or devices. The need is increasingly more important and even urgent as many countries have started to transfer spent fuel to so called 'difficult-to-access' areas such as dry storage casks, reprocessing or geological repositories. Partial defect verification is required by IAEA before spent fuel is placed into 'difficult-to-access' areas. Earlier, Lawrence Livermore National Laboratory (LLNL) has reported the successful development of a new, credible partial defect verification method for pressurized water reactor (PWR) spent fuel assemblies without use of operator data, and further reported the validation experiments using commercial spent fuel assemblies with some missing fuel pins. The method was found to be robust as the method is relatively invariant to the characteristic variations of spent fuel assemblies such as initial fuel enrichment, cooling time, and burn-up. Since then, the PDET system has been designed and prototyped for 17x17 PWR spent fuel assemblies, complete with data acquisition software and acquisition electronics. In this paper, a summary description of the PDET development followed by results of the first successful field testing using the integrated PDET system and actual spent fuel assemblies performed in a commercial spent fuel storage site, known as Central Interim Spent fuel Storage Facility (CLAB) in Sweden will be presented. In addition to partial defect detection initial studies have determined that the tool can be used to verify the operator declared average burnup of the assembly as well as intra-assembly burnup levels. (authors)

Supplemental description of ROSA-IV/LSTF with No.1 simulated fuel-rod assembly

International Nuclear Information System (INIS)

1989-09-01

Forty-two integral simulation tests of PWR small break LOCA (loss-of-coolant accident) and transient were conducted at the ROSA-IV Large-Scale Test Facility (LSTF) with the No.1 simulated fuel-rod assembly between March 1985 and August 1988. Described in the report are supplemental information on modifications of the system hardware and measuring systems, results of system characteristics tests including the initial fluid mass inventory and heat loss distribution for the primary system, and thermal properties for the heater rod materials. These are necessary to establish the correct boundary conditions of each LSTF experiment with the No.1 core assembly in addition to the system data given in the system description report (JAERI-M 84-237). (author)

A Multi-Physics PWR Model for the Load Following

OpenAIRE

Muniglia , Mathieu; Do , Jean-Michel; Jean-Charles , Le Pallec; Grard , Hubert; Verel , Sébastien; David , S.

2016-01-01

International audience; In this paper, a new model of a Pressurized Water Reactor (PWR) is described. This model includes the description of the core as well as a simplified secondary loop: the goal is to reproduce a load-following type transient, where the output power of the plant is controlled by the electric grid. Consequently, the control systems are also modeled, as the control rods or the soluble boron. The reference power plant is a 1300MW electrical PWR, managed with the french G mode.

The PWR spectral code GELS. Pt. 1

International Nuclear Information System (INIS)

Penndorf, K.; Schult, F.; Schulz, G.

1976-01-01

The code procedures group constant libraries for the static PWR design of whatever fuel cycle - Uranium, Thorium, or Plutonium. The whole reach of temperatures is covered and the treatment of strong lumped absorbers as control or burnable poison pins is included. The main features are: 1) Good accuracy in spite of not fitting the material data to critical experiments; 2) speed and relatively low computer equipment; 3) restriction to PWR's only. In case of demands for higher accuracy there is a further restriction concerning the library data of the epithermal resonance absorbers: They are strictly valid only for several special lattice geometrics. Three samples are given each representing a typical application of the code. Two of them likewise are demonstrations of recalculated experiments. (orig.) [de

Optimization of reload core design for PWR

International Nuclear Information System (INIS)

Shen Wei; Xie Zhongsheng; Yin Banghua

1995-01-01

A direct efficient optimization technique has been effected for automatically optimizing the reload of PWR. The objective functions include: maximization of end-of-cycle (EOC) reactivity and maximization of average discharge burnup. The fuel loading optimization and burnable poison (BP) optimization are separated into two stages by using Haling principle. In the first stage, the optimum fuel reloading pattern without BP is determined by the linear programming method using enrichments as control variable, while in the second stage the optimum BP allocation is determined by the flexible tolerance method using the number of BP rods as control variable. A practical and efficient PWR reloading optimization program based on above theory has been encoded and successfully applied to Qinshan Nuclear Power Plant (QNP) cycle 2 reloading design

Fuel assembly design for APR1400 with low CBC

Energy Technology Data Exchange (ETDEWEB)

Hah, Chang Joo, E-mail: changhah@kings.ac.kr [Department of NPP Engineering, KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

2015-04-29

APR 1400 is a PWR (Pressurized Water Reactor) with rated power of 3983 MWth and 241 assemblies. Recently, demand for extremely longer cycle up to 24 months is increasing with challenge of higher critical boron concentration (CBC). In this paper, assembly design method of selecting Gd-rods is introduced to reduce CBC. The purpose of the method is to lower the critical boron concentration of the preliminary core loading pattern (PLP), and consequently to achieve more negative or less positive moderator temperature coefficient (MTC). In this method, both the ratio of the number of low-Gd rod to the number of high-Gd rod (r) and assembly average Gd wt% (w) are the decision variables. The target function is the amount of soluble boron concentration reduction, which can be converted to Δk{sub TARGET}. A set of new designed fuel assembly satisfies an objective function, min [f=∑{sub i}(Δk{sub FA}−Δk{sub i})], and enables a final loading pattern to reach a target CBC. The constraints required to determine a set of Δk are physically realizable pair, (r,w), and the sum of Δk of new designed assemblies as close to Δk{sub TARGET} as possible. New Gd-bearing assemblies selected based on valid pairs of (r,w) are replaced with existing assemblies in a PLP. This design methodology is applied to Shin-Kori Unit 3 Cycle 1 used as a reference model. CASMO-3/MASTER code is used for depletion calculation. CASMO-3/MASTER calculations with new designed assemblies produce lower CBC than the expected CBC, proving that the proposed method works successful.

Surveillance of vibrations in PWR

International Nuclear Information System (INIS)

Espefaelt, R.; Lorenzen, J.; Aakerhielm, F.

1980-07-01

The core of a PWR - including fuel elements, internal structure, control rods and core support structure inside the pressure vessel - is subjected to forces which can cause vibrations. One sensitive means to detect and analyse such vibrations is by means of the noise from incore and excore neutron detector signals. In this project noise recordings have been made on two occasions in the Ringhals 2 plant and the obtained data been analysed using the Studsvik Noise Analysis Program System (SNAPS). The results have been intepreted and a detailed description of the vibrational status of the core and pressure vessel internals has been produced. On the basis of the obtained results it is proposed that neutron signal noise analysis should be performed at each PWR plant in the beginning, middle and end of each fuel cycle and an analysis be made using the methods developed in the project. It would also provide a contribution to a higher degree of preparedness for diagnostic tasks in case of unexpected and abnormal events. (author)

In-Core Fuel Managements for PWRs: Investigation on solution for optimal utilization of PWR fuel through the use of fuel assemblies with differently enriched 235U fuel pins

International Nuclear Information System (INIS)

Caprioli, Sara

2004-04-01

A possibility for more efficient use of the nuclear fuel in a pressurized water reactor is investigated. The alternative proposed here consists of the implementation of PWR fuel assemblies with differently enriched 235 U fuel pins. This possibility is examined in comparison with the standard assembly design. The comparison is performed both in terms of single assembly performance and in the terms of nuclear reactor core performance and fuel utility. For the evaluation of the actual performance of the new assembly types, 5 operated fuel core sequences of R3 (Ringhals' third unit), for the period 1999 - 2004 (cycles 17 - 21) were examined. For every cycle, the standard fresh fuel assemblies have been identified and taken as reference cases for the study of the new type of assemblies with differently enriched uranium rods. In every cycle, assemblies with and without burnable absorber are freshly loaded into the core. The axial enrichment distribution is kept uniform, allowing for a radial (planar) enrichment level distribution only. At an assembly level, it has been observed that the implementation of the alternative enrichment configuration can lead to lower and flatter internal peaking factor distribution with respect to the uniformly enriched reference assemblies. This can be achieved by limiting the enrichment levels distribution to a rather narrow range. The highest enrichment level chosen has the greatest impact on the power distribution of the assemblies. As it increases, the enrichment level drives the internal peaking factor to greater values than in the reference assemblies. Generally, the highest enrichment level that would allow an improvement in the power performance of the assembly lies between 3.95 w/o and 4.17 w/o. The highest possible enrichment level depends on the average enrichment of the overall assembly, which is kept constant to the average enrichment of the reference assemblies. The improvements that can be obtained at this level are rather

ROSA-V large scale test facility (LSTF) system description for the third and fourth simulated fuel assemblies

Energy Technology Data Exchange (ETDEWEB)

Suzuki, Mitsuhiro; Nakamura, Hideo; Ohtsu, Iwao [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment] [and others

2003-03-01

The Large Scale Test Facility (LSTF) is a full-height and 1/48 volumetrically scaled test facility of the Japan Atomic Energy Research Institute (JAERI) for system integral experiments simulating the thermal-hydraulic responses at full-pressure conditions of a 1100 MWe-class pressurized water reactor (PWR) during small break loss-of-coolant accidents (SBLOCAs) and other transients. The LSTF can also simulate well a next-generation type PWR such as the AP600 reactor. In the fifth phase of the Rig-of-Safety Assessment (ROSA-V) Program, eighty nine experiments have been conducted at the LSTF with the third simulated fuel assembly until June 2001, and five experiments have been conducted with the newly-installed fourth simulated fuel assembly until December 2002. In the ROSA-V program, various system integral experiments have been conducted to certify effectiveness of both accident management (AM) measures in beyond design basis accidents (BDBAs) and improved safety systems in the next-generation reactors. In addition, various separate-effect tests have been conducted to verify and develop computer codes and analytical models to predict non-homogeneous and multi-dimensional phenomena such as heat transfer across the steam generator U-tubes under the presence of non-condensable gases in both current and next-generation reactors. This report presents detailed information of the LSTF system with the third and fourth simulated fuel assemblies for the aid of experiment planning and analyses of experiment results. (author)

Development of Out-pile Test Technology for Fuel Assembly Performance Verification

Energy Technology Data Exchange (ETDEWEB)

Chun, Tae Hyun; In, W. K.; Oh, D. S. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)] (and others)

2007-03-15

Out-pile tests with full scale fuel assembly are to verify the design and to evaluate the performance of the final products. HTL for the hydraulic tests and FAMeCT for mechanical/structural tests were constructed in this project. The maximum operating conditions of HTL are 30 bar, 320 .deg. C, and 500 m3/hr. This facility can perform the pressure drop test, fuel assembly uplift test, and flow induced vibration test. FAMeCT can perform the bending and vibration tests. The verification of the developed facilities were carried out by comparing the reference data of the fuel assembly which was obtained at the Westinghouse Co. The compared data showed a good coincidence within uncertainties. FRETONUS was developed for high temperature and high pressure fretting wear simulator and performance test. A performance test was conducted for 500 hours to check the integrity, endurance, data acquisition capability of the simulator. The technology of turbulent flow analysis and finite element analysis by computation was developed. From the establishments of out-pile test facilities for full scale fuel assembly, the domestic infrastructure for PWR fuel development has been greatly upgraded.

New long-cycle small modular PWR cores using particle type burnable poisons for low boron operation

Energy Technology Data Exchange (ETDEWEB)

Yoo, Hoseong; Hwang, Dae Hee [Department of Nuclear Engineering, Kyung Hee University, Deogyeong-daero, GiHeung-gu, Yongin, Gyeonggi-do 446-701 (Korea, Republic of); Hong, Ser Gi, E-mail: sergihong@khu.ac.kr [Department of Nuclear Engineering, Kyung Hee University, Deogyeong-daero, GiHeung-gu, Yongin, Gyeonggi-do 446-701 (Korea, Republic of); Shin, Ho Choel [Core and Fuel Analysis Group, Korea Hydro & Nuclear Power Central Research Institute (KHNP-CRI), Daejon 305-343 (Korea, Republic of)

2017-04-01

Highlights: • New advanced burnable poison rods (BPR) are suggested for low boron operation in PWR. • The new SMR cores have long cycle length of ∼4.5 EFPYs with low boron concentration. • The SMR core satisfies all the design targets and constraints. - Abstract: In this paper, new small long-cycle PWR (Pressurized Water Reactor) cores for low boron concentration operation are designed by employing advanced burnable poison rods (BPRs) in which the BISO (Bi-Isotropic) particles of burnable poison are distributed in a SiC matrix. The BPRs are designed by adjusting the kernel diameter, the kernel material and the packing fraction to effectively reduce the excess reactivity in order to reduce the boron concentration in the coolant and achieve a flat change in excess reactivity over a long operational cycle. In addition, axial zoning of the BPRs was suggested to improve the core performances, and it was shown that the suggested axial zoning of BPRs considerably extends the cycle length compared to a core with no BPR axial zoning. The results of the core physics analyses showed that the cores using BPRs with a B{sub 4}C kernel have long cycle lengths of ∼4.5 EFPYs (Effective Full Power Years), small maximum CBCs (Critical Boron Concentration) lower than 370 ppm, low power peaking factors, and large shutdown margins of control element assemblies.

A Critical Review of Practice of Equating the Reactivity of Spent Fuel to Fresh Fuel in Burnup Credit Criticality Safety Analyses for PWR Spent Fuel Pool Storage

International Nuclear Information System (INIS)

Wagner, J.C.; Parks, C.V.

2000-01-01

This research examines the practice of equating the reactivity of spent fuel to that of fresh fuel for the purpose of performing burnup credit criticality safety analyses for PWR spent fuel pool (SFP) storage conditions. The investigation consists of comparing k inf estimates based on reactivity equivalent fresh fuel enrichment (REFFE) to k inf estimates using the actual spent fuel isotopics. Analyses of selected storage configurations common in PWR SFPs show that this practice yields nonconservative results (on the order of a few tenths of a percent) in configurations in which the spent fuel is adjacent to higher-reactivity assemblies (e.g., fresh or lower-burned assemblies) and yields conservative results in configurations in which spent fuel is adjacent to lower-reactivity assemblies (e.g., higher-burned fuel or empty cells). When the REFFE is determined based on unborated water moderation, analyses for storage conditions with soluble boron present reveal significant nonconservative results associated with the use of the REFFE. This observation is considered to be important, especially considering the recent allowance of credit for soluble boron up to 5% in reactivity. Finally, it is shown that the practice of equating the reactivity of spent fuel to fresh fuel is acceptable, provided the conditions for which the REFFE was determined remain unchanged. Determination of the REFFE for a reference configuration and subsequent use of the REFFE for different configurations violates the basis used for the determination of the REFFE and, thus, may lead to inaccurate, and possibly, nonconservative estimates of reactivity. A significant concentration (approx. 2000 ppm) of soluble boron is typically (but not necessarily required to be) present in PWR SFPs, of which only a portion (le 500 ppm) may be credited in safety analyses. Thus, a large subcritical margin currently exists that more than accounts for errors or uncertainties associated with the use of the REFFE

Commercial radioactive waste management system feasibility with the universal canister concept. Volume 1

International Nuclear Information System (INIS)

Morissette, R.P.; Schneringer, P.E.; Lane, R.K.; Moore, R.L.; Young, K.A.

1986-01-01

A Program Research and Development Announcement (PRDA) was initiated by DOE to solicit from industry new and novel ideas for improvements in the nuclear waste management system. GA Technologies Inc. was contracted to study a system utilizing a universal canister which could be loaded at the reactor and used throughout the waste management system. The proposed canister was developed with the objective of meeting the mission requirements with maximum flexibility and at minimum cost. Canister criteria were selected from a thorough analysis of the spent fuel inventory, and canister concepts were evaluated along with the shipping and storage casks to determine the maximum payload. Engineering analyses were performed on various cask/canister combinations. One important criterion was the interchangeability of the canisters between truck and rail cask systems. A canister was selected which could hold three PWR intact fuel elements or up to eight consolidated PWR fuel elements. One canister could be shipped in an overweight truck cask or six in a rail cask. Economic analysis showed a cost savings of the reference system under consideration at that time

Study of the distribution of hydrogen in a PWR containment with CFD codes; Estudio de la distribucion de hidrogeno en una contencion PWR con codigos CFD

Energy Technology Data Exchange (ETDEWEB)

Jimenez, G.; Matias, R.; Fernandez, K.; Justo, D.; Bocanegra, R.; Mena, L.; Queral, C.

2015-07-01

During a severe accident in a PWR, the hydrogen generated may be distributed in the containment atmosphere and reach the combustion conditions that can cause the containment failure. In this research project, a preliminary study has been done about the capacities of ANSYS Fluent 15.0 and GOTHIC 8.0 to tri dimensional distribution of the hydrogen in a PWR containment during a severe accident. (Author)

Multi-Pack Disposal Concepts for Spent Fuel (Revision 1)

International Nuclear Information System (INIS)

Hardin, Ernest; Matteo, Edward N.; Hadgu, Teklu

2016-01-01