Study of the phenomenon of cathodic pulverisation at low energy; Etude du phenomene de la pulverisation cathodique a basse energie

Energy Technology Data Exchange (ETDEWEB)

Druaux, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1957-07-01

Every time positive ions bombard the cathode of a discharge tube, a continuous destruction of the cathode and a corresponding deposit on the surrounding walls are observed. This phenomenon is known as 'cathodic pulverisation'. It has been known for about a century, but the difficulties of observation and the numerous secondary phenomena which accompany it have for a long time held up the correct explanation of its physical mechanism. At the present time, it can be said that no theory can yet claim to make it completely intelligible. However, cathodic pulverisation can be considered as a particular case of the phenomenon of collisions between atomic particles; in this instance it is a question of the impact of positive ions accelerated by U volts (I{sub U}{sup +}) on the atoms of a solid or liquid target X. (author) [French] Chaque fois que des ions positifs bombardent la cathode d'un tube a decharge, on observe une destruction continue de celle-ci et un depot correspondant sur les parois environnantes. Ce phenomene est appele 'pulverisation cathodique'. Il est connu depuis un siecle environ, mais les difficultes d'observation et les nombreux phenomenes secondaires qui l'accompagnent ont retarde pendant longtemps l'explication correcte de son mecanisme physique. A l'heure actuelle, on peut dire qu'aucune theorie ne peut encore pretendre a son intelligibilite complete. Cependant, on peut considerer la pulverisation cathodique comme un cas particulier du phenomene de chocs entre particules atomiques; en l'occurrence, il s'agit de l'impact d'ions positifs acceleres par U volts (I{sub U}{sup +}) sur les atomes d'une cible X solide ou liquide. (auteur)

Quantification of fusion in ashes from solid fuel combustion

DEFF Research Database (Denmark)

Hansen, Lone Aslaug; Frandsen, Flemming; Dam-Johansen, Kim

1999-01-01

The fusion of ashes produced during solid fuel combustion greatly affects the tendency of these ashes to cause operational problems in utility boilers. In this paper, a new and quantitative laboratory method for assessing the fusion of ashes based on simultaneous thermal analysis, STA, is described...

Utilization of pulverized fuel ash in Malta

International Nuclear Information System (INIS)

Camilleri, Josette; Sammut, Michael; Montesin, Franco E.

2006-01-01

In Malta all of the waste produced is mixed and deposited at various sites around the island. None of these sites were purpose built, and all of the waste is above groundwater level. The landfills are not engineered and do not contain any measures to collect leachate and gases emanating from the disposal sites. Another waste, which is disposed of in landfills, is pulverized fuel ash (PFA), which is a by-product of coal combustion by the power station. This has been disposed of in landfill, because its use has been precluded due to the radioactivity of the ashes. The aim of this study was to analyze the chemical composition of the pulverized fuel ash and to attempt to utilize it as a cement replacement in normal concrete mixes in the construction industry. The levels of radiation emitted from the ashes were measured by gamma spectrometry. The results of this study revealed that although at early ages cement replacement by PFA resulted in a reduction in compressive strength (P = 0), when compared to the reference concrete at later ages the strengths measured on concrete cores were comparable to the reference concrete (P > 0.05). The utilization of PFA up to 20% cement replacement in concrete did not raise the radioactivity of the concrete. In conclusion, utilization of PFA in the construction industry would be a better way of disposing of the ashes rather than controlling the leachate and any radioactivity emitted by the landfilled ashes

Modern power station practice mechanical boilers, fuel-, and ash-handling plant

CERN Document Server

Sherry, A; Cruddace, AE

2014-01-01

Modern Power Station Practice, Second Edition, Volume 2: Mechanical (Boilers, Fuel-, and Ash-Handling Plant) focuses on the design, manufacture and operation of boiler units and fuel-and ash-handling plants.This book is organized into five main topics-furnace and combustion equipment, steam and water circuits, ancillary plant and fittings, dust extraction and draught plant, and fuel-and ash-handling plant.In these topics, this text specifically discusses the influence of nature of coal on choice of firing equipment; oil-burner arrangements, ignition and control; disposition of the heating surf

Effects of ashes in solid fuels on fuel particle charging during combustion in an air stream

Energy Technology Data Exchange (ETDEWEB)

Zakharov, A.G.; Fialkov, B.S.; Mel' nichuk, A.Yu.; Khvan, L.A.

1982-09-01

Black coal from the Karaganda basin is mixed with sodium chloride and graphite. Coal characteristics are given in a table (density, ashes, content of silica, aluminium oxides, iron oxides, calcium oxides, potassium oxides and magnesium oxides). Effects of ash fluctuations on electric potential of fuel particles during combustion are analyzed. Analyses show that with increasing ash content electric potential of fuel particles decreases and reaches the minimum when ash content ranges from 70 to 80 %. Particles with electric potential are generated during chemical processes between carbon and oxygen when coal is burned in an air stream. (5 refs.) (In Russian)

Mathematical modelling of flue gas tempered flames produced from pulverised coal fired with oxygen

Energy Technology Data Exchange (ETDEWEB)

Breussin, A.; Weber, R.; Kamp, W.L. van de

1997-10-01

The combustion of pulverised coal in conventional utility boilers contributes significantly to global CO{sub 2} emissions. Because atmospheric air is used as the combustion medium, the exhaust gases of conventional pulverised coal fired utility boilers contain approximately 15 % CO{sub 2}. This relatively low concentration makes separating and recovering CO{sub 2} a very energy-intensive process. This process can be simplified if N{sub 2} is eliminated from the comburent before combustion by firing the pulverised coal with pure oxygen. However, this concept will result in very high flames temperatures. Flue gas recirculation can be used to moderate the flame temperature, whilst generating a flue gas with a CO{sub 2} concentration of 95 %. In this presentation, both experimental and modelling work will be described. The former deals with identifying the issues related to the combustion of pulverised coal in simulated turbine exhaust gas, particularly with respect to stability, burnout and pollutant emissions. The second part of this presentation describes mathematical modelling of type 2 as well as type 1 swirling pulverised coal flames. Future work will concentrate on high CO{sub 2} levels environments. (orig.)

The relationship of post-fire white ash cover to surface fuel consumption

Science.gov (United States)

Andrew T. Hudak; Roger D. Ottmar; Robert E. Vihnanek; Nolan W. Brewer; Alistair M. S. Smith; Penelope Morgan

2013-01-01

White ash results from the complete combustion of surface fuels, making it a logically simple retrospective indicator of surface fuel consumption. However, the strength of this relationship has been neither tested nor adequately demonstrated with field measurements. We measured surface fuel loads and cover fractions of white ash and four other surface materials (green...

Environmental issues: New techniques for managing and using wood fuel ash

Energy Technology Data Exchange (ETDEWEB)

Fehrs, J.E.; Donovan, C.T. [C.T. Donovan Associates, Inc., Burlington, VT (United States)

1993-12-31

Continued research and development of environmentally-acceptable and cost-effective end uses for wood ash is having a significant affect on the ability to use wood and wood waste for fuel. This is particularly true for ash resulting from treated wood combustion. Concerns about the contents of ash from wood containing paint, stain, preservatives, or other chemicals is one of the largest regulatory barriers to its use as fuel. The purpose of this paper is to: (1) Identify the physical and chemical characteristics of ashes produced from the combustion of untreated and treated wood; (2) Explain the types of {open_quotes}clean, untreated{close_quotes} and {open_quotes}treated{close_quotes} wood that are likely to produce ash that can beneficially used; (3) Describe existing and potential products and end uses for untreated and treated wood ash.

Application of Fly Ash from Solid Fuel Combustion in Concrete

DEFF Research Database (Denmark)

Pedersen, Kim Hougaard

2008-01-01

with implementation of low-NOx combustion technologies. The present thesis concerns three areas of importance within this field: 1) testing of fly ash adsorption behavior; 2) the influence of fuel type and combustion conditions on the ash adsorption behaviour including full-scale experiments at the power plant...... has a low sensitivity toward small variations in AEA adsorption between different fly ashes and it requires further work before a finished procedure is accomplished. Finally, it was shown that changes in temperature affect both test methods. Pulverized fuel has been combusted in an entrained flow...... formation. It was found that the AEA adsorption of the fly ash was reduced up to five times compared to reference operation, when the plant was operated with minimum furnace air staging, three levels of burners instead of four and without recycled flue gas. The lower AEA requirements of the fly ash...

Study over problems related to fuel and ash handling systems; Probleminventering braensle- och askhantering

Energy Technology Data Exchange (ETDEWEB)

Njurell, Rolf; Wikman, Karin [AaF-Energi och Miljoe AB, Stockhom (Sweden)

2003-10-01

There have been a lot of problems related to fuel and ash handling systems since the combustion of different types of biofuels started in the 70s. Many measures have been taken to solve some of the problems, but others have become part of the daily work. The purpose of this study has been to do a compilation of the fuel and ash handling problems that exist at different types of heat and power plants. The study over problems related to fuel and ash handling systems has been carried out through a questionnaire via the Internet. Directors at about 150 energy production plants were contacted by phone or e-mail in the beginning of the project and asked to participate in the study. 72 of these plants accepted to fill in the questionnaire. After several reminders by e-mails and phone calls there were in the end 32 plants that completed the form. Together they reported about 25 problems related to fuel handling and 27 problems related to ash handling. In general each of the plants reported one problem of each kind. Even if the material from the questionnaire is not enough to make statistical analysis a few conclusions can be made about the most common problems, the cause of the problems and where they appear. Fuel handling problems that occur at several plants are stoppage in the conveying equipment, bridging in the boiler silo or the tipping bunker and problems with the sieve for separation. The distribution of the fuel handling problems is almost equal for all equipment parts (receiving, separation, transport etc.). For the ash handling systems problems with transport of dry bottom ash dominate, followed by and the moistening of fly ash and transport of wet bottom ash. Most of the problems related to fuel handling are caused by the fuel quality. For example several plants have reported that bark is a fuel that is hard to handle. Nevertheless the quality for a specific fuel is not always bad when it is delivered to the plant but the fuel quality might change during

Characterisation of ashes produced by co-combustion of recovered fuels and peat

Energy Technology Data Exchange (ETDEWEB)

Frankenhaeuser, M. [Borealis Polymers Oy, Porvoo (Finland)

1997-10-01

The current project focuses on eventual changes in ash characteristics during co-combustion of refuse derived fuel with coal, peat, wood or bark, which could lead to slagging, fouling and corrosion in the boiler. Ashes were produced at fluidised bed (FB) combustion conditions in the 15 kW reactor at VTT Energy, Jyvaeskylae, the fly ash captured by the cyclone was further analysed by XRF at Outokumpu Geotechnical Laboratory, Outokumpu. The sintering behaviour of these ashes was investigated using a test procedure developed at the Combustion Chemistry Research Group at Aabo Akademi University. The current extended programme includes a Danish refuse-derived fuel (RDF), co-combusted with bark/coal (5 tests) and wood/coal (2 tests), a RF from Jyvaskyla (2 tests with peat/coal) and de-inking sludges co- combusted at full-scale with wood waste or paper mill sludge (4 ashes provided by IVO Power). Ash pellets were thermally treated in nitrogen in order to avoid residual carbon combustion. The results obtained show no sintering tendencies below 600 deg C, significant changes in sintering are seen with pellets treated at 1000 deg C. Ash from 100 % RDF combustion does not sinter, 25 % RDF co-combustion with wood and peat, respectively, gives an insignificant effect. The most severe sintering occurs during co-combustion of RDF with bark. Contrary to the earlier hypothesis a 25 % coal addition seems to have a negative effect on all fuel blends. Analysis of the sintering results versus ash chemical composition shows, that (again), in general, an increased level of alkali chlorides and sulphates gives increased sintering. Finally, some results on sintering tendency measurements on ashes from full-scale CFB co-combustion of deinking sludge with wood waste and paper mill sludge are given. This shows that these ashes show very little, if any, sintering tendency, which can be explained from ash chemistry

Ash related behaviour in staged and non-staged combustion of biomass fuels and fuel mixtures

International Nuclear Information System (INIS)

Becidan, Michaël; Todorovic, Dusan; Skreiberg, Øyvind; Khalil, Roger A.; Backman, Rainer; Goile, Franziska; Skreiberg, Alexandra; Jovovic, Aleksandar; Sørum, Lars

2012-01-01

The fate of selected elements (with focus on the important players in corrosion i.e. Na, K, Pb, Zn, Cl and S) are investigated for three biomasses (wood, demolition wood and coffee waste) and six mixtures of these as pellets both with and without air staging in a laboratory reactor. In order to get a complete overview of the combustion products, both online and offline analytical methods are used. Information is collected about: flue gas composition, particle (fly ash) size distribution and composition, bottom ash composition and melting properties. The main findings are: (1) complex interactions are taking place between the mixed fuels during combustion; (2) the mode of occurrence of an element as well as the overall structure of the fuel are important for speciation; (3) the pelletisation process, by bringing chemical elements into intimate contact, may affect partitioning and speciation; (4) staging and mixing might simultaneously have positive and negative effects on operation; (5) staging affects the governing mechanisms of fly ash (aerosols) formation. -- Highlights: ► Complex interactions are taking place between the mixed fuels during combustion. ► The mode of occurrence of an element as well as the overall structure of the fuel are important for speciation. ► The pelletisation process, by bringing chemical elements into intimate contact, may affect partitioning and speciation. ► Staging and mixing might simultaneously have positive and negative effects on operation. ► Staging affects the governing mechanisms of fly ash (aerosols) formation.

Sustainable construction: Composite use of tyres and ash in concrete

Energy Technology Data Exchange (ETDEWEB)

Snelson, D.G.; Kinuthia, J.M.; Davies, P.A.; Chang, S.R. [University of Glamorgan, Pontypridd (United Kingdom). Faculty of Advanced Technology

2009-01-15

An investigation was carried out to establish the physical, mechanical and chemical characteristics of a non-standard (unprocessed) pulverised fuel ash (PFA) and waste tyres from a former landfill site at the Power Station Hill near Church Village, South Wales, United Kingdom. Investigations are on-going to establish the suitability of the fly ash and/or tyres in road construction (embankment and pavement) and also in concrete to be used in the construction of the proposed highway. This paper reports on concrete-based construction where concrete blends (using various levels of PFA as partial replacement for Portland cement (PC), and shredded waste tyres (chips 15-20 mm) as aggregate replacement) were subjected to unconfined compressive strength tests to establish performance, hence, optimising mix designs. Strength development up to 180 days for the concrete made with PC-PFA blends as binders (PC-PFA concrete), with and without aggregate replacement with tyre chips, is reported. The binary PC-PFA concrete does not have good early strength but tends to improve at longer curing periods. The low early strength observed means that PC-PFA concrete cannot be used for structures, hence, only as low to medium strength applications such as blinding, low-strength foundations, crash barriers, noise reduction barriers, cycle paths, footpaths and material for pipe bedding.

Mineralogical investigations into ash deposits of selected brown coals; Mineralogische Untersuchungen an Ascheansaetzen ausgewaehlter Braunkohlen

Energy Technology Data Exchange (ETDEWEB)

Szilagyi, J.; Ullrich, B. [Technische Univ. Dresden, Inst. fuer Geotechnik (Germany)

2003-07-01

Within the framework of the research project financed by the Arbeitsgemeinschaft industrieller Forschungsvereinigungen (AIF) ''Experimental investigations into the formation of ash deposits from stack gases during the combustion of pulverised lignite'' and supervised by the chair of power station technology (Institute of Energy Technology) of the Dresden Technical University, the mineral composition of ash deposits of six different coals were investigated: two coal blends (different countries worldwide), two lignites from east from the River Elbe (types WM and JAe), one from west of the River Elbe and one Rhenish lignite. (orig.)

Identifying fly ash at a distance from fossil fuel power stations

International Nuclear Information System (INIS)

Flanders, P.J.

1999-01-01

A method has been developed to identify fly ash originating at fossil fuel power stations, even at a distance where the ash level is lower by a factor of 1000 from that close to a source. Until now such detection has been difficult and uncertain. The technique combines collection of particles, measurement of magnetization and coercive field, and microscopy. The analysis depends on the fact that ash from iron sulfide in fossil fuels is in the form of spherical magnetite. These particles have a relatively high coercive field H c , near 135 Oe, compared with airborne particulates from soil erosion which have an H c of ∼35 Oe. The coercive field of any sample therefore gives an indication for the percentage of fly ash relative to the total amount of magnetic material that is airborne. The concentration of ash from a large, isolated coal burning power station is found to fall off with the distance from the source, approximately as D -1 . As D increases there is a drop in H c , associated with the reduced amount of fly ash relative to the airborne particulates from soil erosion

Combustion Behaviour of Pulverised Wood - Numerical and Experimental Studies. Part 1 Numerical Study

Energy Technology Data Exchange (ETDEWEB)

Elfasakhany, A.; Xue-Song Bai [Lund Inst. of Tech. (Sweden). Dept. of Heat and Power Engineering

2002-12-01

This report describes a theoretical/numerical investigation of the particle motion and the particle drying, pyrolysis, oxidation of volatile and char in a pulverised biofuel (wood) flame. This work, along with the experimental measurement of a pulverised wood flame in a vertical furnace at TPS, is supported by the Swedish Energy Agency, STEM. The fundamental combustion process of a pulverised wood flame with determined size distribution and anisotropy character is studied. Comprehensive submodels are studied and some models not available in the literature are developed. The submodels are integrated to a CFD code, previously developed at LTH. The numerical code is used to simulate the experimental flame carried out at TPS (as sub-task 2 within the project). The sub-models describe the drying, devolatilization, char formation of wood particles, and the oxidation reaction of char and the gas phase volatile. At the present stage, the attention is focused on the understanding and modelling of non-spherical particle dynamics and the drying, pyrolysis, and oxidation of volatile and char. Validation of the sub-models against the experimental data is presented and discussed in this study. The influence of different factors on the pulverised wood flame in the TPS vertical furnace is investigated. This includes shape of the particles, the effect of volatile release, as well as the orientation of the particles on the motion of the particles. The effect of particle size on the flame structure (distribution of species and temperature along the axis of the furnace) is also studied. The numerical simulation is in close agreement with the TPS experimental data in the concentrations of species O{sub 2}, CO{sub 2} as well as temperature. Some discrepancy between the model simulations and measurements is observed, which suggests that further improvement in our understanding and modeling the pulverised wood flame is needed.

High ash fuels for diesel engines II; Korkean tuhkapitoisuuden omaavan polttoaineen kaeyttoe dieselvoimaloissa II

Energy Technology Data Exchange (ETDEWEB)

Norrmen, E.; Vestergren, R.; Svahn, P. [Wartsila Diesel International Ltd, Vaasa (Finland)

1996-12-01

Heavy fuel oils containing a large amount of ash, that is used in some geographically restricted areas, can cause problems with deposit formation and hot corrosion, leading to burned exhaust gas valves in some diesel engines. The Liekki 2 programs Use of high ash fuel in diesel power plants I and II have been initiated to clarify the mechanisms of deposit formation, and start and propagation of hot corrosion. The aim is to get enough knowledge to enable the development of the Waertsilae diesel engines to be able to handle heavy fuel with a very high ash content. The chemistry, sintering, melting, and corrosiveness of deposits from different part of the diesel engine and on different exhaust valve materials, as well as the chemistry in different depths of the deposit have been investigated. Theories for the mechanisms mentioned above have been developed. Additives changing the sintering/melting point and physical properties of the formed deposits have been screened. Exhaust gas particle measurements have been performed when running on high ash fuel, both without deposit modifying fuel additive and with. The results have been used to verify the ABC (Aerosol Behaviour in Combustion) model, and the particle chemistry and morphology has been examined. Several tests, also high load endurance tests have been run in diesel engines with high ash fuels. (author)

Use of high ash fuel in diesel power plants II; Korkean tuhkapitoisuuden omaavan polttoaineen kaeyttoe dieselvoimaloissa II

Energy Technology Data Exchange (ETDEWEB)

Vestergren, R; Normen, E; Hellen, G [Wartsila Diesel International Ltd Oy, Vaasa (Finland); and others

1997-10-01

Heavy fuel oils containing a large amount of ash are used in some geographically restricted areas. The ash components can cause problems with deposit formation and hot corrosion, leading to burned exhaust gas valves in some diesel engines. The LIEKKI 2 programs Use of high ash fuel in diesel power plants, Part I and II, have been initiated to clarify the mechanisms of deposit formation, and start and propagation of hot corrosion. The aim is to get enough knowledge to enable the development of the Waertsilae diesel engines to be able to handle heavy fuels with a very high ash content. The chemistry during combustion has been studied. The chemical and physical properties of the particles in the exhaust gas, of the deposits, and of exhaust valves have been investigated. Exhaust gas particle measurements have been performed when running on high ash fuel, both with and without deposit modifying fuel additive. Theories for the mechanisms mentioned above have been developed. On the practical side two long time field tests are going on, one with an ash/deposit modifying fuel additive (vanadium chemistry alteration), one with fuel water washing (sodium removal). Seven different reports have been written. (orig.)

The heterogeneous nature of mineral matter, fly-ash and deposits

Energy Technology Data Exchange (ETDEWEB)

Creelman, R.A.; Pohl, J.H.; Devir, G.P.; Su, S. [R.A. Creelman and Associates, Epping, NSW (Australia)

2000-07-01

This paper reports on a series of slagging studies investigating the heterogeneous nature of mineral matter, fly ash and deposits, and how this heterogeneity affects deposition. The data come from low temperature ashing (LTA) of pulverised coal, fly ash from boilers, and deposits from pilot-scale furnaces and boilers. The paper presents optical and scanning electron (SEM) micrographs, electron microprobe analysis (EMPA) and energy dispersive x-ray analysis (EDXRA) of mineral matter, individual fly ash particles, and localised regions of deposits. During combustion, the included mineral matter is transformed into fly ash, melts and partially adheres to the char surface, and may form agglomerated masses. Excluded mineral matter has little chance of encountering another ash particle and agglomerating in the gas phase, but can react with other particles in the wall deposits. Certain fly ash particles adhere to the wall where they can combine with other fly ash particles. Analyses of molten regions of deposits have shown, so far, four mineral phase fields to be responsible for forming difficult deposits with melting points below deposit surface temperatures of 1200 to 1350{sup o}C. These mineral fields include iron cordierite, albite and its silica undersaturated equivalent nepheline, anorthite, and compounds with ratios of Ca to P of 2.3-2.5.

Characterization of ashes from a 100 kWth pilot-scale circulating fluidized bed with oxy-fuel combustion

Energy Technology Data Exchange (ETDEWEB)

Wu, Y.H.; Wang, C.B.; Tan, Y.W.; Jia, L.F.; Anthony, E.J. [Natural Resources Canada, Ottawa, ON (Canada)

2011-09-15

Oxy-fuel combustion experiments have been carried out on an oxygen-fired 100 kW(th) mini-circulating fluidized bed combustion (CFBC) facility. Coal and petroleum coke were used as fuel together with different limestones (and fixed Ca:S molar ratios) premixed with the fuel, for in situ SO{sub 2} capture. The bed ash (BA) and fly ash (FA) samples produced from this unit were collected and characterized to obtain physical and chemical properties of the ash samples. The characterization methods used included X-ray fluorescence (XRF), X-ray diffraction (XRD), char carbon and free lime analysis, thermogravimetric analysis (TGA), and surface analysis. The main purpose of this work is to characterize the CFBC ashes from oxy-fuel firing to obtain a better understanding of the combustion process, and to identify any significant differences from the ash generated by a conventional air-fired CFBC. The primary difference in the sulfur capture mechanism between atmospheric air-fired and oxy-fuel FBC, at typical FBC temperatures (similar to 850{sup o}C), is that, in the air-fired case the limestone sorbents calcine, whereas the partial pressure of CO{sub 2} in oxy-fuel FBC is high enough to prevent calcination, and hence the sulfation process should mimic that seen in pressurized FBC (PFBC). Here, the char carbon content in the fly ash was much higher than that in the bed ash, and was also high by comparison with ash obtained from conventional commercial air-firing CFBC units. In addition, measurements of the free lime content in the bed and fly ash showed that the unreacted Ca sorbent was present primarily as CaCO{sub 3}, indicating that sulfur capture in the oxy-fuel combustor occurred via direct sulfation.

Bio fuel ash in a road construction: impact on soil solution chemistry.

Science.gov (United States)

Thurdin, R T; van Hees, P A W; Bylund, D; Lundström, U S

2006-01-01

Limited natural resources and landfill space, as well as increasing amounts of ash produced from incineration of bio fuel and municipal solid waste, have created a demand for useful applications of ash, of which road construction is one application. Along national road 90, situated about 20 km west of Sollefteå in the middle of Sweden, an experiment road was constructed with a 40 cm bio fuel ash layer. The environmental impact of the ash layer was evaluated from soil solutions obtained by centrifugation of soil samples taken on four occasions during 2001-2003. Soil samples were taken in the ash layer, below the ash layer at two depths in the road and in the ditch. In the soil solutions, pH, conductivity, dissolved organic carbon (DOC) and the total concentration of cations (metals) and anions were determined. Two years after the application of the ash layers in the test road, the concentrations in the ash layer of K, SO4, Zn, and Hg had increased significantly while the concentration of Se, Mo and Cd had decreased significantly. Below the ash layer in the road an initial increase of pH was observed and the concentrations of K, SO4, Se, Mo and Cd increased significantly, while the concentrations of Cu and Hg decreased significantly in the road and also in the ditch. Cd was the element showing a potential risk of contamination of the groundwater. The concentrations of Ca in the ash layer indicated an ongoing hardening, which is important for the leaching rate and the strength of the road construction.

REAL TIME PULVERISED COAL FLOW SOFT SENSOR FOR THERMAL POWER PLANTS USING EVOLUTIONARY COMPUTATION TECHNIQUES

Directory of Open Access Journals (Sweden)

B. Raja Singh

2015-01-01

Full Text Available Pulverised coal preparation system (Coal mills is the heart of coal-fired power plants. The complex nature of a milling process, together with the complex interactions between coal quality and mill conditions, would lead to immense difficulties for obtaining an effective mathematical model of the milling process. In this paper, vertical spindle coal mills (bowl mill that are widely used in coal-fired power plants, is considered for the model development and its pulverised fuel flow rate is computed using the model. For the steady state coal mill model development, plant measurements such as air-flow rate, differential pressure across mill etc., are considered as inputs/outputs. The mathematical model is derived from analysis of energy, heat and mass balances. An Evolutionary computation technique is adopted to identify the unknown model parameters using on-line plant data. Validation results indicate that this model is accurate enough to represent the whole process of steady state coal mill dynamics. This coal mill model is being implemented on-line in a 210 MW thermal power plant and the results obtained are compared with plant data. The model is found accurate and robust that will work better in power plants for system monitoring. Therefore, the model can be used for online monitoring, fault detection, and control to improve the efficiency of combustion.

Binary Effect of Fly Ash and Palm Oil Fuel Ash on Heat of Hydration Aerated Concrete

Science.gov (United States)

Mehmannavaz, Taha; Ismail, Mohammad; Radin Sumadi, Salihuddin; Rafique Bhutta, Muhammad Aamer; Samadi, Mostafa

2014-01-01

The binary effect of pulverized fuel ash (PFA) and palm oil fuel ash (POFA) on heat of hydration of aerated concrete was studied. Three aerated concrete mixes were prepared, namely, concrete containing 100% ordinary Portland cement (control sample or Type I), binary concrete made from 50% POFA (Type II), and ternary concrete containing 30% POFA and 20% PFA (Type III). It is found that the temperature increases due to heat of hydration through all the concrete specimens especially in the control sample. However, the total temperature rises caused by the heat of hydration through both of the new binary and ternary concrete were significantly lower than the control sample. The obtained results reveal that the replacement of Portland cement with binary and ternary materials is beneficial, particularly for mass concrete where thermal cracking due to extreme heat rise is of great concern. PMID:24696646

Influence of the Chernobyl accident on radioactivity of fuel peat and peat ash in Finland

International Nuclear Information System (INIS)

Mustonen, R.; Salonen, S.; Itkonen, A.

1988-04-01

The accident at the Chernobyl nuclear power plant in April 1986 caused very uneven deposition of radionuclides in Finland. The deposited radionuclides were measured in relative high concentrations in fuel peat and especially in peat ash. The radionuclide concentrations were measured at six peat-fired power plants in different parts of Finland throughout the heating season 1986-87. Also evaporation of different radionuclides in peat combustion and their condensation on fly ash particles were studied at four power plants. The 137 Cs-concentrations in compiled peat samples varied between 30 and 3600 Bq kg -1 dry weight and in ash samples between 600 and 68000 Bq kg -1 . Differences in radionuclide concentrations between the power plants were great and also the radionuclide composition in fuel peat varied regionally. The 137 Cs-concentrations of the fly ash after the ash precipitators varied between 12000 and 120000 Bq kg -1 and fly ash emissions varied from 17 to 1100 mg m -3 , depending on the power plant and the load of the boiler. High radioactivity concentrations in precipitator ash caused some restrictions to the utilization of peat ash for various purposes

Characterization of a Treated Palm Oil Fuel Ash | Hassan | Science ...

African Journals Online (AJOL)

Palm oil fuel ash (POFA) has been known to possess a pozzolanic property. ... for 1.5 hours in a ball mill to reduce the particle size and to improve reactivity. ... that POFA is a good candidate for various applications by ceramic industries.

Preliminary measurement of the drag force on a porous cylinder with fluid evolution under conditions relevant to pulverised-fuel combustion

Energy Technology Data Exchange (ETDEWEB)

Dijan Supramono; Graham J. Nathan; Peter J. Ashman; Peter J. Mullinger [University of Adelaide, Adelaide, SA (Australia). Cooperative Research Centre for Clean Power from Lignite, Schools of Chemical Engineering and Mechanical Engineering

2003-07-01

The trajectories of the particles in pulverised coal combustion systems determine their residence times and reaction environments, and hence coal burnout and flame length. The trajectories, in turn, depend upon the drag coefficient of the particle. The effect of the evolution of fluid from the surface of the particle on this coefficient has never been measured before, particularly at the low particle Reynolds numbers that apply during coal combustion. Therefore mathematical models must rely on assumed sphere drag coefficients, which do not account for the effect of fluid evolving from the surface. A technique of using a porous cylinder mounted on a pendulum, instead of a sphere, through which fluid can be forced to evolve, simulating fluid evolution in coal devolatilisation and char burning, is used. The pendulum is capable of measuring drag forces of the order of 10-5 to 10-6 Newton, at Reynolds numbers similar to that experienced by coal particles. This paper presents preliminary measurements of drag force at relevant conditions. The working fluid is water in the first instance, although it will be extended to diluted glycerine in the future. The cross flow is provided by a water tunnel and the ejected fluid is induced by a separate pump. Both the Reynolds number and the ratio of evolution velocity to free-stream velocity are chosen to span conditions relevant to pulverised coal combustion. 16 refs., 5 figs., 2 tabs.

Distribution and leaching characteristics of trace elements in ashes as a function of different waste fuels and incineration technologies.

Science.gov (United States)

Saqib, Naeem; Bäckström, Mattias

2015-10-01

Impact of waste fuels (virgin/waste wood, mixed biofuel (peat, bark, wood chips) industrial, household, mixed waste fuel) and incineration technologies on partitioning and leaching behavior of trace elements has been investigated. Study included 4 grate fired and 9 fluidized boilers. Results showed that mixed waste incineration mostly caused increased transfer of trace elements to fly ash; particularly Pb/Zn. Waste wood incineration showed higher transfer of Cr, As and Zn to fly ash as compared to virgin wood. The possible reasons could be high input of trace element in waste fuel/change in volatilization behavior due to addition of certain waste fractions. The concentration of Cd and Zn increased in fly ash with incineration temperature. Total concentration in ashes decreased in order of Zn>Cu>Pb>Cr>Sb>As>Mo. The concentration levels of trace elements were mostly higher in fluidized boilers fly ashes as compared to grate boilers (especially for biofuel incineration). It might be attributed to high combustion efficiency due to pre-treatment of waste in fluidized boilers. Leaching results indicated that water soluble forms of elements in ashes were low with few exceptions. Concentration levels in ash and ash matrix properties (association of elements on ash particles) are crucial parameters affecting leaching. Leached amounts of Pb, Zn and Cr in >50% of fly ashes exceeded regulatory limit for disposal. 87% of chlorine in fly ashes washed out with water at the liquid to solid ratio 10 indicating excessive presence of alkali metal chlorides/alkaline earths. Copyright © 2015. Published by Elsevier B.V.

Influence of start-ups with fuel-oil on the operation of electrostatic precipitators in pulverised coal boilers

Energy Technology Data Exchange (ETDEWEB)

Navarrete, B.; Vilches, L.F.; Canadas, L.; Salvador, L. [University of Seville, Seville (Spain)

2004-04-01

This article describes the results of a series of tests carried out in a pilot fly ash electrostatic precipitation facility operating with real gases from a 550 MWe pulverized coal-fired power station. The main goal of these tests was to determine the effects of boiler start-ups on the performance of the electrostatic preciptator. The tests were carried out during start-ups of the power station boiler. All tests were carried out with the same fuel. An evaluation was made of the effects of the use of fuel-oil as auxillary fuel in start-ups and shut-downs of the boiler, and different electrostatic precipitators operation procedures were tested during start-ups and shut-downs. The results of the experiments made it possible to assess the relative importance of different variables on the possible deterioration of the efficiency of the precipitators. Also evaluated were operational modes that have demonstrated an improvement in the performance of the precipitators after the transient stage of these operations. As a result of this study, a number of important operational recommendations are made on boiler start-up and shut-down procedures.

Synthesis and characterization of palm oil fuel ash (POFA) and metakaolin based geopolymer for possible application in nanocoating

Science.gov (United States)

Khan, Ihsan Ullah; Bhat, A. H.; Masset, Patrick J.; Khan, Farman Ullah; Rehman, Wajid Ur

2016-11-01

The main aim of this study was to synthesize and characterize highly amorphous geopolymer from palm oil fuel ash (POFA) and metakaolin, to be used as nanocoating. Geopolymers are man-made aluminosilicate materials that are amorphous analogues of zeolites. The geopolymers were made by condensing a mixture of raw materials metakaolin and palm oil fuel ash (POFA) with alkaline activator at a fixed ratio at room temperature. The kaolin type clay was calcined at 700 °C for 4hrs to transform it into amorphous metakaolin which is more reactive precursor for geopolymer formation. The characteristics of metakaolin and geopolymers (metakaolin and palm oil fuel ash based geopolymers) were analyzed by using x-ray fluorescence (XRF), Fourier transform infra-red spectrometry (FTIR), Thermogravimetric analysis (TG/DTA) and scanning electron microscopy with energy dispersive x-ray analysis (SEM-EDX). FTIR revealed the presence of Al-O and Si-O stretching vibrations of amorphous alumino-silicate structure for metakaolin, palm oil fuel ash and geopolymers. SEM-EDX images showed the presence of reaction product complementary to NASH (N = Na2O, A = Al2O3, S = SiO2, H = H2O) solid. The resulting geopolymers that were synthesized with NaOH/Na2SiO3 solution cured at 60 °C for 3 days. The results demonstrated the suitability of metakaolin and palm oil fuel ash (POFA) for synthesis of geopolymer at room temperatures.

Applications of Nano palm oil fuel ash and Nano fly ash in concrete

Science.gov (United States)

Hamada, Hussein M.; Jokhio, Gul Ahmed; Mat Yahaya, Fadzil; Humada, Ali M.

2018-04-01

This paper discusses the applications of Nano waste materials including palm oil fuel ash and fly ash in the concrete production. The implementation of nanotechnology has been instrumental in the development of significant interest among the stakeholders to improve the mechanical and chemical properties of materials involved in the production of concrete. Although many researchers have shown the potential of nanomaterials to increase strength and durability of concrete and improve its physical and chemical properties, there is still a knowledge gap regarding the preparation of Nano waste materials from agricultural waste to use as cement replacement instead of non-renewable materials. Therefore, it should be focused on to study Nano- waste materials to benefit from these characteristics during preparation of concrete mixtures. Therefore, this paper highlights the potential of waste materials in the Nano size to partially replace cement in concrete and achieve the same or better result than the traditional concrete. This paper recommends to conduct further experimental works to improve the concrete material properties by investigating the properties of waste materials in Nano size.

Effect of some pulverised plant materials on the developmental stages of fish beetle, Dermestes maculatus Degeer in smoked catfish (Clarias gariepinus) during storage.

Science.gov (United States)

Fasakin, E A; Aberejo, B A

2002-11-01

The effectiveness of pulverised plant materials; Tithonium diversifolia, Afromomum melegueta, Nicotiana tabacum, Monodora myristica and Piper guineense as ovicidal, larvicidal and adult deterents of fish beetle (Dermestes maculatus) in smoked catfish (Clarias gariepinus) during storage were evaluated. Leaves of T. diversifolia, N. tabacum and seeds of A. melegueta, M. myristica and P. guineese were dried and pulverised into powder. Adults and larvae of third generation (F3) of D. maculatus were introduced into Kilner jars containing disinfested fish samples. Pulverised plant materials were applied to the surface of the fish samples at 10% (w/w) and monitored for 40 days, while egg hatchability of the insects was monitored for seven days. The result showed that all the plant materials had varying degree of insecticidal activities. Pulverised powder of P. guineense and A. melegueta were the most effective and significantly (P 0.05) affected by the plant materials. The percentage weight loss in fish treated with P. guineense and A. melegueta were minimal compared with the untreated fish sample. The result of this study showed that pulverised plant materials obtained from P. guineense and A. melegueta could be used to deter egg hatchability and adult emergence of D. maculatus in smoked catfish during storage. This could also reduce percentage losses due to insect infestation on smoked fish during storage.

Influence of carbonation under oxy-fuel combustion flue gas on the leachability of heavy metals in MSWI fly ash.

Science.gov (United States)

Ni, Peng; Xiong, Zhuo; Tian, Chong; Li, Hailong; Zhao, Yongchun; Zhang, Junying; Zheng, Chuguang

2017-09-01

Due to the high cost of pure CO 2 , carbonation of MSWI fly ash has not been fully developed. It is essential to select a kind of reaction gas with rich CO 2 instead of pure CO 2 . The CO 2 uptake and leaching toxicity of heavy metals in three typical types of municipal solid waste incinerator (MSWI) fly ash were investigated with simulated oxy-fuel combustion flue gas under different reaction temperatures, which was compared with both pure CO 2 and simulated air combustion flue gas. The CO 2 uptake under simulated oxy-fuel combustion flue gas were similar to that of pure CO 2 . The leaching concentration of heavy metals in all MSWI fly ash samples, especially in ash from Changzhou, China (CZ), decreased after carbonation. Specifically, the leached Pb concentration of the CZ MSWI fly ash decreased 92% under oxy-fuel combustion flue gas, 95% under pure CO 2 atmosphere and 84% under the air combustion flue gas. After carbonation, the leaching concentration of Pb was below the Chinese legal limit. The leaching concentration of Zn from CZ sample decreased 69% under oxy-fuel combustion flue gas, which of Cu, As, Cr and Hg decreased 25%, 33%, 11% and 21%, respectively. In the other two samples of Xuzhou, China (XZ) and Wuhan, China (WH), the leaching characteristics of heavy metals were similar to the CZ sample. The speciation of heavy metals was largely changed from the exchangeable to carbonated fraction because of the carbonation reaction under simulated oxy-fuel combustion flue gas. After carbonation reaction, most of heavy metals bound in carbonates became more stable and leached less. Therefore, oxy-fuel combustion flue gas could be a low-cost source for carbonation of MSWI fly ash. Copyright © 2017 Elsevier Ltd. All rights reserved.

Ash Properties of Alternative Biomass

DEFF Research Database (Denmark)

Capablo, Joaquin; Jensen, Peter Arendt; Pedersen, Kim Hougaard

2009-01-01

analysis into three main groups depending upon their ash content of silica, alkali metal, and calcium and magnesium. To further detail the biomass classification, the relative molar ratio of Cl, S, and P to alkali were included. The study has led to knowledge on biomass fuel ash composition influence...... on ash transformation, ash deposit flux, and deposit chlorine content when biomass fuels are applied for suspension combustion....

Status of advanced ultra-supercritical pulverised coal technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-12-01

In pulverised coal combustion (PCC) power plant, increasing the maximum temperature of the steam cycle increases the electrical efficiency, which in turn lowers both coal consumption and flue gas emissions. However, the maximum steam temperature is limited by materials that can operate at these conditions for practical service lifetimes without failure. The EU, USA, Japan, India and China all have material research programmes aiming for the next generation of increased steam temperatures and efficiency, known as advanced ultra-supercritical (AUSC) or 700°C technology. This report reviews developments and status of these major material research programmes.

Thermal and Ash Characterization of Indonesian Bamboo and Its Potential for Solid Fuel and Waste Valorization

Directory of Open Access Journals (Sweden)

Aprilina Purbasari

2016-08-01

Full Text Available Bamboo has been widely used in Indonesia for construction, handicrafts, furniture and other uses. However, the use of bamboo as a biomass for renewable energy source has not been extensively explored. This paper describes the thermal and ash characterization of three bamboo species found in Indonesia, i.e. Gigantochloa apus, Gigantochloa levis and Gigantochloa atroviolacea. Characterization of bamboo properties as a solid fuel includes proximate and ultimate analyses, calorific value measurement and thermogravimetric analysis. Ash characterization includes oxide composition analysis and phase analysis by X-Ray diffraction. The selected bamboo species have calorific value comparable with wood with low nitrogen and sulphur contents, indicating that they can be used as renewable energy sources. Bamboo ash contains high silicon so that bamboo ash has potential to be used further as building materials or engineering purposes. Ash composition analysis also indicates high alkali that can cause ash sintering and slag formation in combustion process. This implies that the combustion of bamboo requires the use of additives to reduce the risk of ash sintering and slag formation. Article History: Received May 15, 2016; Received in revised form July 2nd, 2016; Accepted July 14th, 2016; Available online How to Cite This Article: Purbasari, A., Samadhi, T.W. & Bindar, Y. (2016 Thermal and Ash Characterization of Indonesian Bamboo and its Potential for Solid Fuel and Waste Valorization. Int. Journal of Renewable Energy Development, 5(2, 95-100. http://dx.doi.org/10.14710/ijred.5.2.96-100 

Physicochemical characterizations of nano-palm oil fuel ash

Energy Technology Data Exchange (ETDEWEB)

Rajak, Mohd Azrul Abdul, E-mail: azrulrajak88@gmail.com [Department of Chemistry, Faculty of Science, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru (Malaysia); Preparatory Centre of Science and Technology, Universiti Malaysia Sabah, Jalan UMS, 88400, Kota Kinabalu, Sabah (Malaysia); Majid, Zaiton Abdul, E-mail: zaiton@kimia.fs.utm.my [Department of Chemistry, Faculty of Science, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru (Malaysia); Ismail, Mohammad [Department of Structure and Material, Faculty of Civil Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru (Malaysia)

2015-07-22

Palm Oil Fuel Ash (POFA) is known as a good supplementary cementing material due to its siliceous-rich content. The application of nanotechnology in the pozzolanic materials could invent new functions in the efficiency of physical and chemical properties of materials. Thus, the present study aims to generate nano-sized POFA and characterize the physicochemical properties of nano-palm oil fuel ash (nPOFA). The nPOFA was prepared by mechanically grinding micro POFA using a high intensity ball milling for 6 hours. The physicochemical properties of nPOFA were characterized via X-Ray Fluoresence (XRF), Scanning Emission microscopy- Energy Dispersive X-Ray (SEM-EDX), Transmission Electron Microscope (TEM) and X-Ray Diffraction (XRD). The particle size of nPOFA acquired from TEM analysis was in the range of 20 nm to 90 nm, while the average crystallite size calculated from XRD diffractogram was 61.5 nm. The resulting nPOFA has a BET surface area of 145.35 m{sup 2}/g, which is more than 85% increment in surface area compared to micro-sized POFA. The morphology and elemental studies showed the presence of spherical as well as irregularly shaped and fine nPOFA particles contains with high silicon content. The presence of α-quartz as the major phase of the nPOFA was identified through XRD analysis. The study concludes that nPOFA has the potential as a supplementary cementing material due to the high silica content, high surface area and the unique behaviors of nano-structured particles.

Physicochemical characterizations of nano-palm oil fuel ash

Science.gov (United States)

Rajak, Mohd Azrul Abdul; Majid, Zaiton Abdul; Ismail, Mohammad

2015-07-01

Palm Oil Fuel Ash (POFA) is known as a good supplementary cementing material due to its siliceous-rich content. The application of nanotechnology in the pozzolanic materials could invent new functions in the efficiency of physical and chemical properties of materials. Thus, the present study aims to generate nano-sized POFA and characterize the physicochemical properties of nano-palm oil fuel ash (nPOFA). The nPOFA was prepared by mechanically grinding micro POFA using a high intensity ball milling for 6 hours. The physicochemical properties of nPOFA were characterized via X-Ray Fluoresence (XRF), Scanning Emission microscopy- Energy Dispersive X-Ray (SEM-EDX), Transmission Electron Microscope (TEM) and X-Ray Diffraction (XRD). The particle size of nPOFA acquired from TEM analysis was in the range of 20 nm to 90 nm, while the average crystallite size calculated from XRD diffractogram was 61.5 nm. The resulting nPOFA has a BET surface area of 145.35 m2/g, which is more than 85% increment in surface area compared to micro-sized POFA. The morphology and elemental studies showed the presence of spherical as well as irregularly shaped and fine nPOFA particles contains with high silicon content. The presence of α-quartz as the major phase of the nPOFA was identified through XRD analysis. The study concludes that nPOFA has the potential as a supplementary cementing material due to the high silica content, high surface area and the unique behaviors of nano-structured particles.

The potential for using slags activated with near neutral salts as immobilisation matrices for nuclear wastes containing reactive metals

Science.gov (United States)

Bai, Y.; Collier, N. C.; Milestone, N. B.; Yang, C. H.

2011-06-01

The UK currently uses composite blends of Portland cement and other inorganic cementitious material such as blastfurnace slag and pulverised fuel ash to encapsulate or immobilise intermediate and low level radioactive wastes. Typically levels up 9:1 blast furnace slag:Portland cement or 4:1 pulverised fuel ash:Portland cement are used. Whilst these systems offer many advantages, their high pH causes corrosion of various metallic intermediate level radioactive wastes. To address this issue, lower pH/weakly alkaline cementitious systems have to be explored. While the blast furnace slag:Portland cement system is referred to as a composite cement system, the underlying reaction is actually an indirect activation of the slag hydration by the calcium hydroxide generated by the cement hydration, and by the alkali ions and gypsum present in the cement. However, the slag also can be activated directly with activators, creating a system known as alkali-activated slag. Whilst these activators used are usually strongly alkaline, weakly alkaline and near neutral salts can also be used. In this paper, the potential for using weakly alkaline and near neutral salts to activate slag in this manner is reviewed and discussed, with particular emphasis placed on the immobilisation of reactive metallic nuclear wastes.

The mechanical and physical properties of concrete containing polystyrene beads as aggregate and palm oil fuel ash as cement replacement material

Science.gov (United States)

Adnan, Suraya Hani; Abadalla, Musab Alfatih Salim; Jamellodin, Zalipah

2017-10-01

One of the disadvantages of normal concrete is the high self-weight of the concrete. Density of the normal concrete is in the range of 2200 kg/m3 to 2600 kg/ m3. This heavy self-weight make it as an uneconomical structural material. Advantages of expended polystyrene beads in lightweight concrete is its low in density which can reduce the dead load (self-weight) Improper disposal of the large quantity of palm oil fuel ash which has been produced may contribute to environmental problem in future. In this study, an alternative of using palm oil fuel ash as a cement replacement material is to improve the properties of lightweight concrete. The tests conducted in this study were slump test, compression strength, splitting tensile and water absorption test. These samples were cured under water curing condition for 7, 28 and 56 days before testing. Eight types of mixtures were cast based on percentage (25%, 50%) of polystyrene beads replacement for control samples and (25%, 50%) of polystyrene beads by different ratio 10%, 15%, and 20% replacement of palm oil fuel ash, respectively. Samples with 25% polystyrene beads and 10% palm oil fuel ash obtained the highest compressive strength which is 16.8 MPa, and the splitting tensile strength is 1.57 MPa. The water absorption for samples 25%, 50% polystyrene and 20% palm oil fuel ash is 3.89% and 4.67%, respectively which is lower compared to control samples.

Ash behavior during hydrothermal treatment for solid fuel applications. Part 1: Overview of different feedstock

International Nuclear Information System (INIS)

Mäkelä, Mikko; Fullana, Andrés; Yoshikawa, Kunio

2016-01-01

Highlights: • Ash behavior of 29 different feedstock interpreted using multivariate data analysis. • Two different groups identified based on char ash content and ash yield. • Solubility of individual elements evaluated based on a smaller data set. • Ash from industrial sludge contained anthropogenic metals with low solubility. - Abstract: Differences in ash behavior during hydrothermal treatment were identified based on multivariate data analysis of literature information on 29 different feedstock. In addition, the solubility of individual elements was evaluated based on a smaller data set. As a result two different groups were distinguished based on char ash content and ash yield. Virgin terrestrial and aquatic biomass, such as different types of wood and algae, in addition to herbaceous and agricultural biomass, bark, brewer’s spent grain, compost and faecal waste showed lower char ash content than municipal solid wastes, anaerobic digestion residues and municipal and industrial sludge. Lower char ash content also correlated with lower ash yield indicating differences in chemical composition and ash solubility. Further evaluation of available data showed that ash in industrial sludge mainly contained anthropogenic Al, Fe and P or Ca and Si with low solubility during hydrothermal treatment. Char from corn stover, miscanthus, switch grass, rice hulls, olive, artichoke and orange wastes and empty fruit bunch had generally higher contents of K, Mg, S and Si than industrial sludge although differences existed within the group. In the future information on ash behavior should be used for enhancing the fuel properties of char based on feedstock type and hydrothermal treatment conditions.

Combustion behaviour and deposition characteristics of Cynara Cardunculus/Greek lignite co-firing under various thermal shares in a thermal pilot-scale facility

Energy Technology Data Exchange (ETDEWEB)

Fuller, Aaron; Maier, Joerg; Scheffknecht, Guenter [Stuttgart Univ. (Germany). Inst. of Combustion and Power Plant Technology; Pawlak-Kruczek, Halina [Wroclaw Univ. of Technology (Poland). Inst. of Heat Engineering and Fluid Mechanics; Karampinis, Emmanouil; Grammelis, Panagiotis; Kakaras, Emmanuel [Centre for Research and Technology Hellas, Ptolemais (Greece). Chemical Process and Energy Resources Inst.; National Technical Univ. of Athens (Greece). Lab. of Steam Boilers and Thermal Plants

2013-06-01

The combustion of herbaceous biomass in industrial boilers, either as co-firing fuel or in dedicated combustion units, possess significant operating challenges due to increased risks for corrosion and slagging/fouling. The present work aims at investigating the combustion behaviour of Cynara Cardunculus (cardoon) in a range of thermal shares (0 to 100 %) with a Greek lignite. Combustion tests were performed in a 0.5 MW thermal input pulverised fuel pilot-scale test facility. Deposits were characterised in terms of morphological and ash fusion behaviour, and slagging/fouling tendencies were determined. (orig.)

Modelling methods for co-fired pulverised fuel furnaces

Energy Technology Data Exchange (ETDEWEB)

L. Ma; M. Gharebaghi; R. Porter; M. Pourkashanian; J.M. Jones; A. Williams [University of Leeds, Leeds (United Kingdom). Energy and Resources Research Institute

2009-12-15

Co-firing of biomass and coal can be beneficial in reducing the carbon footprint of energy production. Accurate modelling of co-fired furnaces is essential to discover potential problems that may occur during biomass firing and to mitigate potential negative effects of biomass fuels, including lower efficiency due to lower burnout and NOx formation issues. Existing coal combustion models should be modified to increase reliability of predictions for biomass, including factors such as increased drag due to non-spherical particle sizes and accounting for organic compounds and the effects they have on NOx emission. Detailed biomass co-firing models have been developed and tested for a range of biomass fuels and show promising results. 32 refs., 4 figs., 3 tabs.

The Influence of Particle Size, Fluidization Velocity, and Fuel Type on Ash-Induced Agglomeration in Biomass Combustion

Energy Technology Data Exchange (ETDEWEB)

Gatternig, Bernhard, E-mail: bernhard.gatternig@cbi.uni-erlangen.de; Karl, Jürgen [Chair of Energy Process Engineering, Friedrich-Alexander University Erlangen-Nürnberg, Nuremberg (Germany)

2014-11-19

Agglomeration of the bed material is one of the main obstacles for biomass utilization in fluidized bed combustors. Especially, high-potential fuels such as fast growing energy crops or biogeneous residues are affected because of their high content of alkaline metals. Despite ongoing research efforts, the knowledge base on what fuels are affected is still limited. This paper describes the design and installation of two lab-scale reactors for the experimental determination of agglomeration temperatures. The reactor concept and measurement method were developed under consideration of experiences from existing test rigs published in literature. Preliminary tests confirmed a reproducibility of ±5°C for both new reactors. The results of an extended measurement campaign (156 test runs of 25 fuel species at a wide range of the operational parameters “bed particle size,” “gas velocity,” and “bed ash accumulation”), based on “design of experiment” (DoE) criteria, showed high-agglomeration tendencies for residues (e.g., dried distillery grains, corn cobs) while woody energy crops (e.g., willow, alder) exhibited very stable combustion behavior. The operating parameters influenced the agglomeration behavior to a lesser degree than different ash compositions of fuel species tested. An interpolation within the DoE factor space allowed for a subsequent comparison of our results with experiments reported in literature. Good agreement was reached for fuels of comparable ash composition considering the interpolation errors of ±32°C on average.

Concentrations of inorganic elements in biomass fuels and recovery in the different ash fractions

NARCIS (Netherlands)

Obernberger, I.; Biedermann, F.; Widmann, W.; Riedl, R.

1997-01-01

Inorganic elements and compounds in biomass fuels influence the combustion process and the composition of the ashes produced. Consequently, knowledge about the material fluxes of inorganic elements and compounds during biomass combustion for different kinds of biofuels and their influencing

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature.

Science.gov (United States)

Saqib, Naeem; Bäckström, Mattias

2014-12-01

Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine content have significant effects on partitioning characteristics by increasing the formation and vaporization of highly volatile metal chlorides. Zinc and cadmium concentrations in fly ash increase with the incineration temperature. Copyright © 2014 Elsevier Ltd. All rights reserved.

Compressive strength and microstructural analysis of fly ash/palm oil fuel ash based geopolymer mortar

International Nuclear Information System (INIS)

Ranjbar, Navid; Mehrali, Mehdi; Behnia, Arash; Alengaram, U. Johnson; Jumaat, Mohd Zamin

2014-01-01

Highlights: • Results show POFA is adaptable as replacement in FA based geopolymer mortar. • The increase in POFA/FA ratio delay of the compressive development of geopolymer. • The density of POFA based geoploymer is lower than FA based geopolymer mortar. - Abstract: This paper presents the effects and adaptability of palm oil fuel ash (POFA) as a replacement material in fly ash (FA) based geopolymer mortar from the aspect of microstructural and compressive strength. The geopolymers developed were synthesized with a combination of sodium hydroxide and sodium silicate as activator and POFA and FA as high silica–alumina resources. The development of compressive strength of POFA/FA based geopolymers was investigated using X-ray florescence (XRF), X-ray diffraction (XRD), Fourier transform infrared (FTIR), and field emission scanning electron microscopy (FESEM). It was observed that the particle shapes and surface area of POFA and FA as well as chemical composition affects the density and compressive strength of the mortars. The increment in the percentages of POFA increased the silica/alumina (SiO 2 /Al 2 O 3 ) ratio and that resulted in reduction of the early compressive strength of the geopolymer and delayed the geopolymerization process

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition, chlorine content and temperature

Energy Technology Data Exchange (ETDEWEB)

Saqib, Naeem, E-mail: naeem.saqib@oru.se; Bäckström, Mattias, E-mail: mattias.backstrom@oru.se

2014-12-15

Highlights: • Different solids waste incineration is discussed in grate fired and fluidized bed boilers. • We explained waste composition, temperature and chlorine effects on metal partitioning. • Excessive chlorine content can change oxide to chloride equilibrium partitioning the trace elements in fly ash. • Volatility increases with temperature due to increase in vapor pressure of metals and compounds. • In Fluidized bed boiler, most metals find themselves in fly ash, especially for wood incineration. - Abstract: Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature. Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine

Ash chemistry and sintering, verification of the mechanisms

Energy Technology Data Exchange (ETDEWEB)

Hupa, M.; Skrifvars, B.J. [Aabo Akademi, Turku (Finland)

1996-12-01

In this project four sintering mechanisms have been studied, i.e., partial melting with a viscous liquid, partial melting with a non-viscous liquid, chemical reaction sintering and solid state sintering. The work has aimed at improving the understanding of ash sintering mechanisms and quantifying their role in combustion and gasification. The work has been oriented in particular on the understanding of biomass ash behavior. The work has not directly focused on any specific technical application. However, results can also be applied on other fuels such as brown coal, petroleum coke, black liquor and different types of wastes (PDF, RDF, MSW). In one part of study the melting behavior was calculated for ten biomass ashes and compared with lab measurements of sintering tendencies. The comparison showed that the T{sub 15} temperatures, i.e. those temperatures at which the ashes contained 15 % molten phase, correlated fairly well with the temperature at which the sintering measurements detected sintering. This suggests that partial melting can be predicted fairly accurate for some ashes already with the today existing thermodynamic calculation routines. In some cases, however the melting calculations did not correlate with the detected sintering temperatures. In a second part detailed measurements on ash behavior was conducted both in a semi full scale CFB and a lab scale FBC. Ashes and deposits were collected and analyzed in several different ways. These analyses show that the ash chemistry shifts radically when the fuel is shifted. Fuels with silicate based ashes behaved totally different than those with an oxide or salt based ash. The chemistry was also affected by fuel blending. The ultimate goal has been to be able to predict the ash thermal behavior during biomass thermal conversion, using the fuel and ash elemental analyses and a few operational key parameters as the only input data. This goal has not yet today been achieved. (author)

Review of palm oil fuel ash and ceramic waste in the production of concrete

Science.gov (United States)

Natasya Mazenan, Puteri; Sheikh Khalid, Faisal; Shahidan, Shahiron; Shamsuddin, Shamrul-mar

2017-11-01

High demand for cement in the concrete production has been increased which become the problems in the industry. Thus, this problem will increase the production cost of construction material and the demand for affordable houses. Moreover, the production of Portland cement leads to the release of a significant amount of CO2 and other gases leading to the effect on global warming. The need for a sustainable and green construction building material is required in the construction industry. Hence, this paper presents utilization of palm oil fuel ash and ceramic waste as partial cement replacement in the production of concrete. Using both of this waste in the concrete production would benefit in many ways. It is able to save cost and energy other than protecting the environment. In short, 20% usage of palm oil fuel ash and 30% replacement of ceramic waste as cement replacement show the acceptable and satisfactory strength of concrete.

The Swedish Ash Programme 2002-2008. Biomass, wastes, peat - any solid fuel but coal

Energy Technology Data Exchange (ETDEWEB)

Bjurstroem, Henrik; Herbert, Roger

2009-07-15

In Sweden, producers of combustion residues have since 2002 implemented a collaborative applied RandD programme aimed at the utilisation of combustion residues (ash). The fuels are biomass, wastes, peat - any solid fuel but coal. In this report, the main lines of the programme are described: Covers for landfills and mine tailings; Civil works, e.g. road-buildings, where both geotechnical and environmental questions have been addressed; Cement and concrete applications; Compensating soils for removing biomass and the mineral nutrients in the biomass. The emphasis of the Programme is on environmental questions, even if technical questions have been treated. The time perspective in this context is much longer than the 3-5 years that are usual in an applied RandD programme, i.e. decades after ash has been placed on a site, e.g. in a road, or spread to forest soil. New test fields have been created in the programme and old test fields have been evaluated in order to gather available information

Fly Ash Formation during Suspension-Firing of Biomass. Effects of Residence Time and Fuel-Type

DEFF Research Database (Denmark)

Damø, Anne Juul; Jensen, Peter Arendt; Jappe Frandsen, Flemming

2017-01-01

particles were subjected to various analyses, including char burnout level, particle size distribution, elemental composition, and particle morphology and composition. Furthermore, the transient release, i.e. the vaporization of the flame-volatile inorganic elements K, Cl and S, from the burning fuel...... particles to the gas phase, has been quantified by using two different calculation methods. The ash formation mechanisms were found to be quite similar for straw and wood. The degree of conversion (char burn-out level) was generally good at residence times ≥ 1s. The size distribution of the residual fly ash...

Combustion of Biosolids in a Bubbling Fluidized Bed, Part 1: Main Ash-Forming Elements and Ash Distribution with a Focus on Phosphorus.

Science.gov (United States)

Skoglund, Nils; Grimm, Alejandro; Ohman, Marcus; Boström, Dan

2014-02-20

This is the first in a series of three papers describing combustion of biosolids in a 5-kW bubbling fluidized bed, the ash chemistry, and possible application of the ash produced as a fertilizing agent. This part of the study aims to clarify whether the distribution of main ash forming elements from biosolids can be changed by modifying the fuel matrix, the crystalline compounds of which can be identified in the raw materials and what role the total composition may play for which compounds are formed during combustion. The biosolids were subjected to low-temperature ashing to investigate which crystalline compounds that were present in the raw materials. Combustion experiments of two different types of biosolids were conducted in a 5-kW benchscale bubbling fluidized bed at two different bed temperatures and with two different additives. The additives were chosen to investigate whether the addition of alkali (K 2 CO 3 ) and alkaline-earth metal (CaCO 3 ) would affect the speciation of phosphorus, so the molar ratios targeted in modified fuels were P:K = 1:1 and P:K:Ca = 1:1:1, respectively. After combustion the ash fractions were collected, the ash distribution was determined and the ash fractions were analyzed with regards to elemental composition (ICP-AES and SEM-EDS) and part of the bed ash was also analyzed qualitatively using XRD. There was no evidence of zeolites in the unmodified fuels, based on low-temperature ashing. During combustion, the biosolid pellets formed large bed ash particles, ash pellets, which contained most of the total ash content (54%-95% (w/w)). This ash fraction contained most of the phosphorus found in the ash and the only phosphate that was identified was a whitlockite, Ca 9 (K,Mg,Fe)(PO 4 ) 7 , for all fuels and fuel mixtures. With the addition of potassium, cristobalite (SiO 2 ) could no longer be identified via X-ray diffraction (XRD) in the bed ash particles and leucite (KAlSi 2 O 6 ) was formed. Most of the alkaline-earth metals

Ash behavior during hydrothermal treatment for solid fuel applications. Part 2: Effects of treatment conditions on industrial waste biomass

International Nuclear Information System (INIS)

Mäkelä, Mikko; Yoshikawa, Kunio

2016-01-01

Highlights: • Effect of treatment conditions on composition and solubility of ash. • Ash dissolution and yield governed by liquid pH and calcium carbonate solubility. • Dissolution of calcium carbonate decreases ash fusion temperature during combustion. • Decreasing the ash content of sludge can weaken ash properties for combustion. - Abstract: This second half of our work on ash behavior concentrates on the effects of hydrothermal treatment conditions on paper sludge. Ash composition and solubility were determined based on treatment temperature, reactor solid load and liquid pH using experimental design and univariate regression methods. In addition, ash properties for combustion were evaluated based on recent developments on ash classification. Based on the results, all experimental variables had a statistically significant effect on ash yields. Only reactor solid load was statistically insignificant for char ash content, which increased based on increasing treatment temperature due to the decomposition of organic components. Ash dissolution and ash yield were governed by liquid pH and the generation of acids mainly due to the solubility of calcium carbonate identified as the main mineral species of paper sludge. Dissolution of calcium carbonate however decreased ash fusion temperatures more likely causing problems during char incineration. This indicated that decreasing the ash content of sludge during hydrothermal treatment can actually weaken ash properties for solid fuel applications.

Exposure to fuel-oil ash and welding emissions during the overhaul of an oil-fired boiler.

Science.gov (United States)

Liu, Youcheng; Woodin, Mark A; Smith, Thomas J; Herrick, Robert F; Williams, Paige L; Hauser, Russ; Christiani, David C

2005-09-01

The health effects of exposure to vanadium in fuel-oil ash are not well described at levels ranging from 10 to 500 microg/m(3). As part of a larger occupational epidemiologic study that assessed these effects during the overhaul of a large oil-fired boiler, this study was designed to quantify boilermakers' exposures to fuel-oil ash particles, metals, and welding gases, and to identify determinants of these exposures. Personal exposure measurements were conducted on 18 boilermakers and 11 utility workers (referents) before and during a 3-week overhaul. Ash particles < 10 microm in diameter (PM(10), mg/m(3)) were sampled over full work shifts using a one-stage personal size selective sampler containing a polytetrafluoroethylene filter. Filters were digested using the Parr bomb method and analyzed for the metals vanadium (V), nickel (Ni), iron (Fe), chromium (Cr), cadmium (Cd), lead (Pb), manganese (Mn), and arsenic (As) by inductively coupled plasma mass spectrometry. Nitrogen dioxide (NO(2)) was measured with an Ogawa passive badge-type sampler and ozone (O(3)) with a personal active pump sampler.Time-weighted average (TWA) exposures were significantly higher (p < 0.05) for boilermakers than for utility workers for PM(10) (geometric mean: 0.47 vs. 0.13 mg/m(3)), V (8.9 vs. 1.4 microg/m(3)), Ni (7.4 vs. 1.8 microg/m(3)) and Fe (56.2 vs. 11.2 microg/m(3)). Exposures were affected by overhaul time periods, tasks, and work locations. No significant increases were found for O(3) or NO(2) for boilermakers or utility workers regardless of overhaul period or task group. Fuel-oil ash was a major contributor to boilermakers' exposure to PM(10) and metals. Vanadium concentrations sometimes exceeded the 2003 American Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value.

Radioisotope conveyor ash meter

International Nuclear Information System (INIS)

Savelov, V.D.

1994-01-01

Radioisotope conveyor ash meter realizes persistent measuring of ashiness of coal and products of its enrichment on the belt conveyor without contact. The principle of ash meter acting is based on functional dependence of the gamma radiation flows backscattering intensity of radioisotope sources from the ash volume content in the controlled fuel. Facility consists from the ashiness transducer and the processing and control device

Pyrochemical head-end treatment for fast reactor fuel elements

International Nuclear Information System (INIS)

Avogadro, A.

1978-01-01

The paper presents the R and D work performed at Ispra and Mol during the period 1965-1975 in order to find a way to overcome technical and economical difficulties arising when the conventional reprocessing is applied to fast reactor fuel elements. The work had been directed towards 3 specific topics: a) liquid-metal decladding of spent stainless steel - clad fuels (solinox process). b) oxidative pulverisation by fused salts and extraction of volatile fission products (satex process). c) Pyrochemical separation of plutonium from the bulk of the fuel

Effect of Additives and Fuel Blending on Emissions and Ash-Related Problems from Small-Scale Combustion of Reed Canary Grass

Directory of Open Access Journals (Sweden)

Sébastien Fournel

2015-07-01

Full Text Available Agricultural producers are interested in using biomass available on farms to substitute fossil fuels for heat production. However, energy crops like reed canary grass contain high nitrogen (N, sulfur (S, potassium (K and other ash-forming elements which lead to increased emissions of gases and particulate matter (PM and ash-related operational problems (e.g., melting during combustion. To address these problematic behaviors, reed canary grass was blended with wood (50 wt% and fuel additives (3 wt% such as aluminum silicates (sewage sludge, calcium (limestone and sulfur (lignosulfonate based additives. When burned in a top-feed pellet boiler (29 kW, the four blends resulted in a 17%–29% decrease of PM concentrations compared to pure reed canary grass probably because of a reduction of K release to flue gas. Nitrogen oxides (NOx and sulfur dioxide (SO2 emissions varied according to fuel N and S contents. This explains the lower NOx and SO2 levels obtained with wood based products and the higher SO2 generation with the grass/lignosulfonate blend. The proportion of clinkers found in combustion ash was greatly lessened (27%–98% with the use of additives, except for lignosulfonate. The positive effects of some additives may allow agricultural fuels to become viable alternatives.

Experimental Assessment of the Mass of Ash Residue During the Burning of Droplets of a Composite Liquid Fuel

Science.gov (United States)

Glushkov, D. O.; Zakharevich, A. V.; Strizhak, P. A.; Syrodoi, S. V.

2018-05-01

An experimental study has been made of the regularities of burning of single droplets of typical compositions of a composite liquid fuel during the heating by an air flow with a varied temperature (600-900 K). As the basic components of the compositions of the composite liquid fuel, use was made of the: waste of processing (filter cakes) of bituminous coals of ranks K, C, and T, waste motor, turbine, and transformer oils, process mixture of mazut and oil, heavy crude, and plasticizer. The weight fraction of a liquid combustible component (petroleum) product) ranged within 0-15%. Consideration has been given to droplets of a composite liquid fuel with dimensions (radius) of 0.5 to 2 mm. Conditions of low-temperature initiation of combustion to ensure a minimum possible mass of solid incombustible residue have been determined. Petroleum products have been singled out whose addition to the composition of the composite liquid fuel tends to increase the ash mass (compared to the corresponding composition without a liquid combustible component). Approximation dependences have been obtained which permit predicting the influence of the concentration of the liquid petroleum product as part of the composite liquid fuel on the ash-residue mass.

Pyrometric fuel particle measurements in pressurised reactors

Energy Technology Data Exchange (ETDEWEB)

Hernberg, R; Joutsenoja, T [Tampere Univ. of Technology (Finland)

1997-10-01

A fibre-optic two-colour pyrometric technique for fuel particle temperature and size measurement is modified and applied to three pressurised reactors of different type in Finland, Germany and France. A modification of the pyrometric method for simultaneous in situ measurement of the temperature and size of individual pulverised coal particles at the pressurised entrained flow reactor of VTT Energy in Jyvaeskylae was developed and several series of measurements were made in order to study the effects of oxygen concentration (3-30 vol%) and pressure (0.2-1.0 MPa) on the particle temperature. The fuels used in the experiments were Westerholt, Polish and Goettelborn hvb coals, Gardanne lignite and Niederberg anthracite. The initial nominal fuel particle size varied in the experiments from 70 to 250 ,{mu}m and the gas temperature was typically 1173 K. For the anthracite also the effects of gas temperature (1073-1423K) and CO{sub 2} concentration (6-80 vol%) were studied. In Orleans a fibreoptic pyrometric device was installed to a pressurised thermogravimetric reactor of CNRS and the two-colour temperatures of fuel samples were measured. The fuel in the experiments was pulverised Goettelborn char. The reliability of optical temperature measurement in this particular application was analysed. In Essen a fibre-optic pyrometric technique that is capable to measure bed and fuel particle temperatures was applied to an atmospheric fluidised bed reactor of DMT. The effects of oxygen concentration (3-8 vol%) and bed temperature (1123-1193 K) on the fuel particle temperature were studied. The fuels in these were Westerholt coal and char and EBV-coal. Some results of these measurements are presented. The project belonged to EU`s Joule 2 extension research programme (contract JOU2-CT93-0331). (orig.)

Uranium content of coal ashes from Southern Brazil coal fueled power stations, by the fission track registration technique

International Nuclear Information System (INIS)

Morales, R.K.

1981-01-01

The feasibility of the application of the fission track registration technique for the determination of uranium in coal ashes was shown. The wet method was employed using as detector the Makrofol KG=10 μm, manufactured by Bayer. The coal ashes were originated from coal-fueled power stations localized in Southern Brazil. The results obtained ranged from 10 to 27 mg U/kg. Since the total error variation was from 18,4% to 23,8%, the method used was considered excellent. The determination of the uranium content in coal ashes is of considerable interest in environmental control in power stations, in their vicinity and wherever these ashes are used or stored. The technique used is the work proved to be very appropriate for the purpose aimed at. (Author) [pt

Ash deposition and high temperature corrosion at combustion of aggressive fuels

Energy Technology Data Exchange (ETDEWEB)

Hede Larsen, O [I/S Fynsvaerket, Faelleskemikerne, Odense (Denmark); Henriksen, N [Elsamprojekt A/S, Faelleskemikerne, Fredericia (Denmark)

1996-12-01

In order to reduce CO{sub 2} emission, ELSAM is investigating the possibilities of using biomass - mainly straw - for combustion in high efficiency power plants. As straw has very high contents of chlorine and potassium, a fuel with high corrosion and ash deposition propensities has been introduced. ELSAM has investigated 3 ultra supercritical boiler concepts for combustion of straw alone or together with coal: (1) PF boilers with a relatively low share of straw, (2) CFB boilers with low to high share of straw and (3) vibrating grate boilers with 100% straw. These investigations has mainly been full-scale tests with straw fed into existing boilers. Corrosion tests have been performed in these boilers using temperature regulated probes and in-plant test tubes in existing superheaters. The corrosion has been determined by detailed measurements of wall thickness reduction and light optical microscopic measurements of the material degradation due to high temperature corrosion. Corrosion mechanisms have been evaluated using SEM/EDX together with thermodynamical considerations based on measurements of the chemical environment in the flue gas. Ash deposition is problematic in CFB boilers and in straw fired boilers, especially in years with high potassium and chlorine content of the straw. This ash deposition also is related to condensation of KCl and can probably only be handled by improved cleaning devices. (EG)

Radionuclide concentration in fuels and ash products from biofuel heating plants

International Nuclear Information System (INIS)

Erlandsson, B.; Hedvall, R.; Mattsson, S.

1995-01-01

The activity concentration of the radionuclides K-40, Ac-228, Pa-234, Mn-54, Co-60, Zr-95, Ru-106, Ag-110m, Sb-125, Cs-134, Cs-137 and Ce-144 have been investigated in peat wood chips and ash products from 13 Swedish district heating plants during the winter seasons of 1986/1987, 1988/89, 1989/90 and 1990/91. There is a significant decrease in the activity concentration of Cs-137 in the fuel which is especially pronounced between the first two seasons, 86/87 and 88/89 after the Chernobyl accident. In spite of the varying deposition of Cs-137 over the country it has been possible to give a relation between the activity concentration in the peat and wood chips as a function of the deposition. The Swedish biofuel heating plants of which 35-40 are burning peat and 70-75 chips have been divided in three groups according to the activity concentration in the ash products. The mean Cs-137 concentration in ash and the total activity 'produced' per year in Sweden have been calculated. The maximum concentration in air at ground level and the corresponding effective dose rate of inhaled Cs-137 as a function of the emission rates of flue gases from stacks with varying heights and during different weather conditions has been calculated. 16 refs, 18 tabs, 4 figs

Exergo-Ecological Assessment Of Auxiliary Fuel Injection Into Blast-Furnace

Directory of Open Access Journals (Sweden)

Stanek W.

2015-06-01

Full Text Available Metallurgy represents complex technological chain supplied with different kinds of primary resources. Iron metallurgy based on blast-furnace process, dominates in world steel production. Metallurgical coke is the basic fuel in this case. Its production is connected with several environmental disadvantageous impacts. One of them is the extended production chain from primary energy to final energy. The reduction of coke consumption in the process can be achieved e.g. by injection of auxiliary fuels or increasing the thermal parameters in the process. In present injection of pulverised coal dominates while recirculation of top-gas seems to be future technology. However, the latter one requires the CO2 removal that additionally extended the production chain. The evaluation of resources management in complex energy-technological systems required application of advanced method based on thermodynamics. In the paper the system exergo-ecological assessment of pulverised coal injection into blast-furnace and top-gas recirculation has been applied. As a comparative criterion the thermo-ecological cost has been proposed.

Shedding of ash deposits

DEFF Research Database (Denmark)

Zbogar, Ana; Frandsen, Flemming; Jensen, Peter Arendt

2009-01-01

Ash deposits formed during fuel thermal conversion and located on furnace walls and on convective pass tubes, may seriously inhibit the transfer of heat to the working fluid and hence reduce the overall process efficiency. Combustion of biomass causes formation of large quantities of troublesome...... ash deposits which contain significant concentrations of alkali, and earth-alkali metals. The specific composition of biomass deposits give different characteristics as compared to coal ash deposits, i.e. different physical significance of the deposition mechanisms, lower melting temperatures, etc....... Low melting temperatures make straw ashes especially troublesome, since their stickiness is higher at lower temperatures, compared to coal ashes. Increased stickiness will eventually lead to a higher collection efficiency of incoming ash particles, meaning that the deposit may grow even faster...

Production of mineral ash-wool

International Nuclear Information System (INIS)

Micevic, Z.; Djekic, S.

1996-01-01

The project entitled 'Production of Mineral Ash-Wool' presents a new technology of possible use of the fly ash, generated as a waste product from the fossil fueled power plants, as a basic raw material for manufacturing of different products from a new mineral ash-wool. The wide area of mineral ash-wool application (civil engineering, industry, power generation, etc.) and the advantages of this new technology (important raw material obtained free of charge, substitution of expensive silicate stone, use of electric energy for melting instead for coke, vicinity of factory location close to the fossil fueled power plant, lower product price, reduction of environmental pollution, etc.) have resulted in the performance of the bench scale tests. Positive results have been obtained, as a good initial base for the realization of this project. The named study as an detailed analysis has been carried out for the assessment of: supply and sales market, analysis of possible and selection of an optimal location of the factory in the frame of fossil fueled power plant 'Kosovo', selection of the production capacity and alternative preliminary technical designs of the factory for the mineral ash-wool production. For the studied alternatives, specifications and capital investments evaluations for equipment and works (mechanical, civil engineering and electromechanical part) have been made as well as assessments of production costs. Based on the performed economical and financial analyses, as well as the sensitivity analyses one could be concluded that the investments in the factory for the mineral ash-wool production is highly economically acceptable. (author). 1 fig., 1 tab., 3 refs

Radioactivity concentration and heavy metal content in fuel oil and oil-ashes in Venezuela

International Nuclear Information System (INIS)

Barros, H.; Sajo-Bohus, L.; Abril, J.M.; Greaves, E.D.

2004-01-01

During the last years an intensive national program was developed to determine the environmental radioactivity levels in Venezuela. Gamma dose and the radon concentrations indoors, in drinking water, in caves and in artificial cavities including the effect of radon transported to the surface with the earth gas have been studied. To continue this project the oil and other natural energy resource should be considered. It is expected that the environmental radiation level is modified in regions where the oil industrial activity is more aggressive such as in the Zulia State and the Faja Petrolifera del Orinoco, (Central Region). In these regions Venezuela is producing 1.750 thousand barrels of oil from the near-to-the- surface or deep oil drilling. Petroleum constitutes an important source of energy and as the majority of natural source contains radionuclides and their disintegration products, being U, Ra, Pb, Bi, Po and K the most often encountered. The combustion of petroleum concentrate in the ashes those radioelements, and later enter the environment by different ways producing adverse effects on the quality of man life. The concentration of radioelements varies greatly between oil fields, then we still requiring local survey studies in this area. Moreover due to the recent national interest in recycling processes, it becomes important to take precaution in the selection of materials that may contain by-products of industrial origin, including oil. In fact the oil ashes, oil slurry and other mining by-products are thought to be employable in the building industry. The concentration of radioactivity in the ash from thermoelectric power plants that use petroleum as a primary energy source was determined. The analysis include the two major thermoelectric power plants in Venezuela, Ricardo Zuluaga on the northern sea side of Caracas and Planta Centro on the littoral of Carabobo State. The study cover different samples: fuel oil No 6, ashes, heavy and medium petroleum

Durability Properties of Palm Oil Fuel Ash Self Compacting Concrete

Directory of Open Access Journals (Sweden)

T. Ofuyatan

2015-02-01

Full Text Available Self Compacting Concrete (SCC is a new innovation in technology that can flow readily into place under its own self weight and fill corner areas of reinforcement structures without the need to vibrate and without segregation of its constitute. The problem of durability of concrete structures due to inadequate compaction by skilled workers has become a source of concern globally. The shortage of skilled manpower, noise and vibration of equipment on construction sites has led to the development of self compacting concrete. This paper presents an experimental study on the durability properties of Self Compacting Concrete with partial placement of Palm Oil Fuel Ash (POFA. Twelve POFA self-compacting concretes of various strength grades were designed at varying percentages of 0, 5, 10, 15, 20, 25 and 30%. The concrete with no placement of ash served as control. Conplast SP432MS was used as superplasticiser in the mix. The experiments are carried out by adopting a water-powder ratio of 0.36. Workability of the fresh concrete is determined by using tests such as: slump flow, T50, V-funnel and L-Box tests. The durability of concrete is tested by acid resistance, sulphate attack and saturated water absorption at the age of 14, 28, 56 and 90 days.

Massive use of pulverized fuel ash in concrete for the construction of a U.K. power station

International Nuclear Information System (INIS)

Davies, D.R.; Kitchener, J.N.

1996-01-01

This paper describes the incorporation and benefits of pulverized fuel ash (PFA) in nearly 620,000 m 2 of concrete used in the construction of the UK's first commercial pressurized light water nuclear reactor power station, Sizewell B, Suffolk. Overall nearly 100,000 t of PFA, 1,300 t of sintered fly ash lightweight aggregate, and nearly 137,000 t of Ordinary Portland Cement (OPC) were used in the works. Generally in the construction of the main power station buildings, structural concrete with a characteristic strength of 45 N/mm 2 was placed and included fly ash as 40% of the cementitious component. Also, concrete with fly ash as 50% of the cementitious component was placed as mass fill. The program of research is reported, including sulfate resistance, heat of hydration,elastic properties, alkali-silica reaction, and long-term strength test results. Test and field results are presented and discussed. Strict quality assurance procedures were enforced and statistical summaries are offered to give an insight into the quality of control exercised. Test work and long-term results are also outlined

Conversion of coal-fired bottom ash to fuel and construction materials.

Science.gov (United States)

Koca, Huseyin; Aksoy, Derya Oz; Ucar, Reyhan; Koca, Sabiha

2017-07-01

In this study, solid wastes taken from Seyitomer coal-fired power plant bottom ashes were subjected to experimental research to obtain a carbon-rich fraction. The possible recycling opportunities of remaining inorganic fraction in the cement and concrete industry was also investigated. Flotation technique was used to separate unburned carbon from inorganic bottom ashes. Collector type, collector, dispersant and frother amounts, and pulp density are the most important variables in the flotation technique. A number of flotation collectors were tested in the experiments including new era flotation reactives. Optimum collector, dispersant and frother dosages as well as optimum pulp density were also determined. After experimental work, an inorganic fraction was obtained, which included 5.41% unburned carbon with 81.56% weight yield. These properties meets the industrial specifications for the cement and concrete industry. The carbon content of the concentrate fraction, obtained in the same experiment, was enhanced to 49.82%. This fraction accounts for 18.44% of the total amount and can be mixed to the power plant fuel. Therefore total amount of the solid waste can possibly be recycled according to experimental results.

STRATEGIES AND TECHNOLOGY FOR MANAGING HIGH-CARBON ASH

Energy Technology Data Exchange (ETDEWEB)

Robert Hurt; Eric Suuberg; John Veranth; Xu Chen; Indrek Kulaots

2004-02-13

The overall objective of the present project was to identify and assess strategies and solutions for the management of industry problems related to carbon in ash. Specific issues addressed included: (1) the effect of parent fuel selection on ash properties and adsorptivity, including a first ever examination of the air entrainment behavior of ashes from alternative (non-coal) fuels; (2) the effect of various low-NOx firing modes on ash properties and adsorptivity based on pilot-plant studies; and (3) the kinetics and mechanism of ash ozonation. This laboratory data has provided scientific and engineering support and underpinning for parallel process development activities. The development work on the ash ozonation process has now transitioned into a scale-up and commercialization project involving a multi-industry team and scheduled to begin in 2004. This report describes and documents the laboratory and pilot-scale work in the above three areas done at Brown University and the University of Utah during this three-year project.

Combustion of pulverized fuel under oxycoal conditions at low oxygen concentrations

Energy Technology Data Exchange (ETDEWEB)

Toporov D.; Foerster M.; Kneer R. [RWTH Aachen University, Aachen (Germany). Institute of Heat and Mass Transfer

2007-07-01

Oxycoal combustion followed by post-combustion CO{sub 2} sequestration has gained justified interest as an option for significant and relatively quick reduction of emissions from fossil fuel power generation, while taking advantage of the existing power plant infrastructure. Burning pulverised coal in a mixture of CO{sub 2}/O{sub 2} instead of air, however, will lead to modified distributions of temperature, species, and radiation fluxes inside the combustion chamber causing a retroaction on the homogeneous and heterogeneous reactions. Utilizing a burner design, which was optimised for coal combustion in air, for oxycoal combustion will lead to flame instability and poor burnout. Stabilisation of the combustion process can be obtained by: i) an increased oxygen concentration (more than 21% vol.) in the oxidiser mixture, thus achieving similar reaction rates and temperature levels to a pulverised fuel-air flame without significant changes to the flame aerodynamics. ii) modifications to the burner aerodynamics, as presented here. The results in this study are obtained in the frame of OXYCOAL-AC, the research project, having the aim to burn a pulverised coal in a CO{sub 2}/O{sub 2}-atmosphere with oxygen, produced from high-temperature ceramic membrane thus leading to higher efficiency of the whole oxycoal process. Numerical and experimental investigations of a stable oxycoal flame, obtained with {le} 21% oxygen concentration in the burning mixture at the RWTH test facility are reported. Two different burner designs are considered, conclusions concerning the achievement of a stable oxycoal flame at O{sub 2} volume concentrations equal and less to the one of oxygen in air are derived. 8 refs., 7 figs., 1 tab.

Three-dimensional simulation of flow and combustion for pulverised coal injection

Energy Technology Data Exchange (ETDEWEB)

Guo, B.Y.; Zulli, P.; Rogers, H.; Mathieson, J.G.; Yu, A.B. [BlueScope Steel Research, Port Kembla, NSW (Australia)

2005-07-01

A three-dimensional numerical model of pulverised coal injection has been developed for simulating coal flow and combustion in the tuyere and raceway of a blast furnace. The model has been used to simulate previously reported combustion tests, which feature an inclined co-axial lance with an annular cooling gas. The predicted coal burnout agrees well with that measured for three coals with volatile contents and particle size ranging between 20.2-36.4% and particle sizes 1-200 {mu}m. Many important phenomena including flow asymmetry, recirculating flow and particle dispersion in the combustion chamber have been predicted. The current model can reproduce the experimental observations including the effects on burnout of coal flowrate and the introduction of methane for lance cooling.

Associative properties of 137Cs in biofuel ashes

International Nuclear Information System (INIS)

Ravila, A.; Holm, E.

1999-01-01

The present study aims to reveal how radiocesium is associated to the ash particles derived from biofuel combustion. A sequential extraction procedure was carried out for the characterisation of radiocesium speciation in ash generated by different fuels and burner types. The ash types considered were fly ash and bottom ash collected from Swedish district heating plants using bark wood or peat as fuel. A fraction of the radiocesium in biofuel ash can easily become solubilised and mobilised by water and also, a significant fraction of the radionuclides can be bound to the ash particles in cation-exchangeable forms. Therefore, at using the ash derived from biofuels to recycle mineral nutrients for forestry or short rotation coppicing, radiocesium solubilised and leached from the ash by rains has a potential to rather quickly enter the rooting zone of forest vegetation or energy crops. On the other hand, radiocesium strongly bound to the ash will migrate slowly into the soil column with the successive accumulation of litter and in the process act to maintain the external dose rate at an elevated level for a long time. The results of the sequential extraction procedure and activity determination of the different extracted fractions implies that the bioavailable fraction of radiocesium in ash from bark, wood or peat is in the range between 20-85% of the total ash contents. Peat ash collected from a powder burner strongly retained a large fraction (70-90%) of its radiocesium content while the peat ash from a continuos fluidized bed type burner retained nearly 100% of the radiocesium in the bottom ash and only about 15% in the fly ash

Fly ash: Chemical-physical and mineralogical characterization

International Nuclear Information System (INIS)

Paoletti, L.; Diociaiuti, M.; Ziemacki, G.; Viviano, G.; Gianfagna, A.

1992-01-01

Fly ash from fossil fuel power plants, municipal waste incinerators and refuse fueled boilers is now being utilized as road construction material. With the aim of facilitating health risk assessments of this practice by providing a sound basis for thorough toxicological examinations, this paper reports on a study in which the crystalline and amorphous constituents of fly ash, according to type of combustion plant and fuel, were identified and analyzed by the use of various analytical techniques which included: scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and absorption, X-ray, and energy loss spectroscopy

Characterisation of solid recovered fuels for direct co-firing in large-scale PF power plants

Energy Technology Data Exchange (ETDEWEB)

Dunnu, Gregory

2013-04-01

Solid Recovered Fuels are solid fuels prepared from high calorific fractions of non-hazardous waste materials intended to be co-fired in coal power plants and industrial furnaces (CEN/TC 343). They are composed of a variety of materials of which some, although recyclable in theory, may be in a form that makes their recycling an unsound option. The SRF with a typical size range of 3 mm through 25 mm are to be directly co-fired in an existing pulverised coal power plant. In comparison to pulverised coal, the particle size distribution of the SRF is of several magnitudes higher, resulting in a different burnout behaviour. Size reduction of the SRF to a fraction similar to coal is not economically feasible. The aim here is, therefore, the direct co-firing of the solid recovered fuels in the boilers without any further size reduction. This approach, however, bears the risk of incomplete combustion if the injection points of the solid recovered fuels are not optimally selected. Accordingly, the prediction of the burner levels, at which the solid recovered fuels should be injected and whether or not a complete combustion will be achieved under full load condition, is the primary objective of this dissertation. In this research work, laboratory experiments have been conducted to forecast the success of co-firing the SRF in a commercial pulverised coal power plant. It involves the analyses of the fuel and its intermediate chars generated at conditions comparable to boiler conditions to determine some characteristic parameters, namely the burnout time, the aerodynamic lift velocity, the drag coefficient and the apparent densities. The data gathered from the laboratory experiments are transferred to boiler conditions to determine the particle trajectories and the maximum distance likely to travel before they are completely converted in the boiler. Different scenarios are examined and based on the results the best boiler injection points are predicted. Furthermore, an on

Ash formation, deposition, corrosion, and erosion in conventional boilers

Energy Technology Data Exchange (ETDEWEB)

Benson, S.A.; Jones, M.L. [Univ. of North Dakota, Grand Forks, ND (United States)

1995-12-01

The inorganic components (ash-forming species) associated with coals significantly affect boiler design, efficiency of operation, and lifetimes of boiler parts. During combustion in conventional pulverized fuel boilers, the inorganic components are transformed into inorganic gases, liquids, and solids. This partitioning depends upon the association of the inorganic components in the coal and combustion conditions. The inorganic components are associated as mineral grains and as organically associated elements, and these associations of inorganic components in the fuel directly influence their fate upon combustion. Combustion conditions, such as temperature and atmosphere, influence the volatility and the interaction of inorganic components during combustion and gas cooling, which influences the state and size composition distribution of the particulate and condensed ash species. The intermediate species are transported with the bulk gas flow through the combustion systems, during which time the gases and entrained ash are cooled. Deposition, corrosion, and erosion occur when the ash intermediate species are transported to the heat-transfer surface, react with the surface, accumulate, sinter, and develop strength. Research over the past decade has significantly advanced understanding of ash formation, deposition, corrosion, and erosion mechanisms. Many of the advances in understanding and predicting ash-related issues can be attributed to advanced analytical methods to determine the inorganic composition of fuels and the resulting ash materials. These new analytical techniques have been the key to elucidation of the mechanisms of ash formation and deposition. This information has been used to develop algorithms and computer models to predict the effects of ash on combustion system performance.

Electrodialytic removal of Cd from biomass combustion fly ash suspensions

DEFF Research Database (Denmark)

Kirkelund, Gunvor M.; Ottosen, Lisbeth M.; Damoe, Anne J.

2013-01-01

was investigated with the aim of enabling reuse of the ashes. The ashes originated from combustion of straw (two ashes), wood chips, and co-firing of wood pellets and fuel oil, respectively. A series of laboratory scale electrodialytic remediation experiments were conducted with each ash. The initial Cd...

A scanning electron microscopy study of ash, char, deposits and fuels from straw combustion and co-combustion of coal and straw

Energy Technology Data Exchange (ETDEWEB)

Sund Soerensen, H.

1998-07-01

The SEM-study of samples from straw combustion and co-combustion of straw and coal have yielded a reference selection of representative images that will be useful for future comparison. The sample material encompassed potential fuels (wheat straw and grain), bottom ash, fly ash and deposits from straw combustion as well as fuels (coal and wheat straw), chars, bottom ash, fly ash and deposits from straw + coal co-combustion. Additionally, a variety of laboratory ashes were studied. SEM and CCSEM analysis of the samples have given a broad view of the inorganic components of straw and of the distribution of elements between individual ash particles and deposits. The CCSEM technique does, however, not detect dispersed inorganic elements in biomass, so to get a more complete visualization of the distribution of inorganic elements additional analyses must be performed, for example progressive leaching. In contrast, the CCSEM technique is efficient in characterizing the distribution of elements in ash particles and between ash fractions and deposits. The data for bottom ashes and fly ashes have indicated that binding of potassium to silicates occurs to a significant extent. The silicates can either be in the form of alumino-silicates or quartz (in co-combustion) or be present as straw-derived amorphous silica (in straw combustion). This process is important for two reasons. One is that potasium lowers the melting point of silica in the fly ash, potentially leading to troublesome deposits by particle impaction and sticking to heat transfer surfaces. The other is that the reaction between potassium and silica in the bottom ash binds part of the potassium meaning that it is not available for reaction with chlorine or sulphur to form KCl or K{sub 2}SO{sub 4}. Both phases are potentially troublesome because they can condense of surfaces to form a sticky layer onto which fly ash particles can adhere and by inducing corrosion beneath the deposit. It appears that in the studied

Granulated wood ash to forest soil - Ecological effects

International Nuclear Information System (INIS)

Rosen, K.; Eriksson, H.; Clarholm, M.; Lundkvist, H.; Rudebeck, A.

1993-01-01

This report describes research concerning ecological effects of wood ash recycling to forest soils. The main part of the minerals in the wood fuels are retained in the ashes after combustion. By returning the ashes back to the cleared forest areas, the mineral losses can be reduced. Adding ashes and limestone is a method to vitalize acidified forest soils and restore the production capacity. 48 refs, 26 figs, 8 tabs

Characterisation of supplementary fuels for co-combustion with pulverised coal

NARCIS (Netherlands)

Heikkinen, J.M.

2005-01-01

The current and future energy policy aims at increasing the share of renewable energy in worlds energy supply. One possibility to enhance energy production by renewable sources within a short term is co-combustion. This means co-firing biomass and waste with fossil fuels at existing power plants

Water permeabilities of pulverized fuel ash; Bifuntan sekitanbai no tosui tokusei

Energy Technology Data Exchange (ETDEWEB)

Ichikawa, T [Center for Coal Utilization, Japan, Tokyo (Japan); Nagataki, S [Niigata University, Niigata (Japan); Hosoda, N [Kumagai Gumi Co. Ltd., Tokyo (Japan); Utsuki, T [The Coal Mining Research Center, Japan, Tokyo (Japan); Kubo, H [Obayashi Corp., Tokyo (Japan)

1996-09-01

It is intended to establish a technology to utilize coal ash in bulk to deal with its increasing production. In order to expand its use into earth engineering materials, two kinds of combustion ashes produced from dust coal burning power plants were used for studies using different kinds of tests. The tests were carried out on strength properties, water permeability, and characteristics of dissolving trace amounts of chemical constituents, with regard to addition effects of cement into compacted and slurry-state dust coal burned ashes. The derived findings may be summarized as follows: as the strength properties, the strength for both of the compacted and slurry-state ashes increases as the cement addition ratio is increased; growth of the strength due to the cement addition ratio and material age varies depending on the kinds of dust coal burned ash; comparison of strengths of the compacted and the slurry-state ashes indicates the strength of the latter ash is about one-third to quarter of that of the former ash; water permeability of the ashes decreases both in the compacted and slurry- state ashes as the cement addition ratio is increased; and the cement addition ratio gives greater impact to the water permeability than the density of the ashes. 28 figs., 5 tabs.

Approaches to control the quality of cementitious PFA grouts for nuclear waste encapsulation

Energy Technology Data Exchange (ETDEWEB)

Rice, G.; Miles, N.; Farris, S. [University of Nottingham, Nottingham (United Kingdom). Nottingham Mining & Minerals Centre

2007-05-15

Pulverised Fuel Ash (PFA) is combined with Ordinary Portland Cement (OPC) powder and water to form cementitious grouts for use in various aspects of nuclear waste encapsulation. Whilst specific PFA supplies in the United Kingdom currently deliver adequate grout performance it is also clear that some alternative supplies result in inferior performance, leading to concern over the long term availability of suitable raw material. This paper presents the results of an investigation into the characteristics of PFA that affect critical aspects of grout performance and identifies strategies that could be used to ensure high quality PFA supplies in the future.

Wildland fire ash: Production, composition and eco-hydro-geomorphic effects

Science.gov (United States)

Bodi, Merche B.; Martin, Deborah; Balfour, Victoria N.; Santin, Cristina; Doerr, Stefan H.; Pereira, Paulo; Cerda, Artemi; Mataix-Solera, Jorge

2014-01-01

Fire transforms fuels (i.e. biomass, necromass, soil organic matter) into materials with different chemical and physical properties. One of these materials is ash, which is the particulate residue remaining or deposited on the ground that consists of mineral materials and charred organic components. The quantity and characteristics of ash produced during a wildland fire depend mainly on (1) the total burned fuel (i.e. fuel load), (2) fuel type and (3) its combustion completeness. For a given fuel load and type, a higher combustion completeness will reduce the ash organic carbon content, increasing the relative mineral content, and hence reducing total mass of ash produced. The homogeneity and thickness of the ash layer can vary substantially in space and time and reported average thicknesses range from close to 0 to 50 mm. Ash is a highly mobile material that, after its deposition, may be incorporated into the soil profile, redistributed or removed from a burned site within days or weeks by wind and water erosion to surface depressions, footslopes, streams, lakes, reservoirs and, potentially, into marine deposits.Research on the composition, properties and effects of ash on the burned ecosystem has been conducted on material collected in the field after wildland and prescribed fires as well as on material produced in the laboratory. At low combustion completeness (typically T  450 °C), most organic carbon is volatized and the remaining mineral ash has elevated pH when in solution. It is composed mainly of calcium, magnesium, sodium, potassium, silicon and phosphorous in the form of inorganic carbonates, whereas at T > 580 °C the most common forms are oxides. Ash produced under lower combustion completeness is usually darker, coarser, and less dense and has a higher saturated hydraulic conductivity than ash with higher combustion completeness, although physical reactions with CO2 and when moistened produce further changes in ash characteristics.As a new

Quality characteristics of Greek fly ashes and potential uses

Energy Technology Data Exchange (ETDEWEB)

Skodras, G.; Grammelis, P.; Kakaras, E. [Institute for Solid Fuels Technology and Applications, Ptolemais (Greece); Karangelos, D.; Anagnostakis, M.; Hinis, E. [Nuclear Engineering Section, Mechanical Engineering Department, National Technical University of Athens, Athens (Greece)

2007-01-15

The main characteristics of fly ash from Greek coal-fired boilers are presented in this paper in relation to its exploitation potential. Both fuel and fly ash samples were collected and analyzed according to the ASTM Standards. Apart from the typical analyses (proximate, ultimate, ash analysis and calorific value), an ICP-AES spectrometer was used for the analysis of heavy metals in the ash. Experimental measurements in order to determine the radioactivity content of raw fuel and the fly ash were carried out as well. A representative fly ash sample from Ptolemais power plant was evaluated and tested as filler in Self-Compacting Concrete (SCC). Ashes from the Greek brown coal are classified in type C, most of the fly ash being produced in Ptolemais of Northern Greece, while the rest in Megalopolis. Ptolemais fly ash is rich in calcium compounds, while Megalopolis fly ash contains more pyrite. Increased heavy metal concentrations are observed in the fly ash samples of Greek coal. Greek fly ash appears to have not only pozzolanic but also hydraulic behaviour. Furthermore, Greek fly ash, depending on its origin, may have relatively high natural radioactivity content, reaching in the case of Megalopolis fly ash 1 kBq kg{sup -1} of {sup 226}Ra. The laboratory results showed that fly ashes can be a competitive substitute to conventional limestone filler material in SCC. Fly ash is mostly used in Greece in cement industry replacing cement clinker and aiming to the production of special types of Portland cements. However, a more aggressive utilisation strategy should be developed, since low quantities of the total produced fly ash are currently further utilised. (author)

Reduced ash-related operational problems by co-combustion peat and agricultural fuels; Minskade askrelaterade driftsproblem genom inblandning av torv i aakerbraenslen

Energy Technology Data Exchange (ETDEWEB)

Oehman, Marcus; Bostroem, Dan; Skoglund, Nils; Grimm, Alejandro; Boman, Christoffer; Kofod-Hansen, Marie

2010-06-15

The objectives of the project were: To determine the admixing levels for different peat classes to various energy crops (straw, Salix and Reed canary grass) that are required to reach positive effects regarding slagging, deposit formation/(high temperature corrosion) and bed agglomeration; and, To demonstrate the possibilities to reduce the occurrence of ash related operational problems in combustion of energy crops upon admixing peat. Operational experiences and research of effects of co-firing peat and energy crops are scarce. Some previous tests in bench scale indicated though, on a strong reduction of the agglomeration tendency and lowering of the agglomeration temperature for straw and Salix at a peat admixing level corresponding to 15 - 20 weight% (on DS basis). A reduction in the amount of emitted fine particles was also observed in these experiments. However, care must be taken in the choice of peat. Some Carex dominated peats with high Si contents may cause problems with slagging. Another conclusion from the mentioned bench scale tests was that peats with relative high Ca/Si ratios should be selected to minimize the risk of slagging and bed agglomeration. Thermochemical modelling was performed to determine the effects of peat admixture, on slagging-, deposit formation- (corrosion)- and bed agglomeration tendencies during combustion of straw, willow and reed canary grass with high and low ash content. These results and previously conducted bench scale experiments were used as a basis for determining combinations of fuel and peat admixtures for the demonstration experiments. The calculations were performed with admixing levels of 0-, 5-, 15, 25-, and 40 weight% (on DS basis) of four peat samples to the investigated four crop fuels. The used peat samples were typical carex-containing Swedish peat with differences in e.g. silicon-, calcium- and sulfur contents. A number of the model calculations were qualitatively validated against previously conducted

Faecal-wood biomass co-combustion and ash composition analysis.

Science.gov (United States)

Somorin, Tosin Onabanjo; Kolios, Athanasios J; Parker, Alison; McAdam, Ewan; Williams, Leon; Tyrrel, Sean

2017-09-01

Fuel blending is a widely used approach in biomass combustion, particularly for feedstocks with low calorific value and high moisture content. In on-site sanitation technologies, fuel blending is proposed as a pre-treatment requirement to reduce moisture levels and improve the physiochemical properties of raw faeces prior to drying. This study investigates the co-combustion performance of wood dust: raw human faeces blends at varying air-to-fuel ratios in a bench-scale combustor test rig. It concludes with ash composition analyses and discusses their potential application and related problems. The study shows that a 50:50 wood dust (WD): raw human faeces (FC) can reduce moisture levels in raw human faeces by ∼40% prior to drying. The minimum acceptable blend for treating moist faeces without prior drying at a combustion air flow rate of 14-18 L/min is 30:70 WD: FC. For self-sustained ignition and flame propagation, the minimum combustion temperature required for conversion of the fuel to ash is ∼400 °C. The most abundant elements in faecal ash are potassium and calcium, while elements such as nickel, aluminium and iron are in trace quantities. This suggests the potential use of faecal ash as a soil conditioner, but increases the tendency for fly ash formation and sintering problems.

Reed as a gasification fuel: a comparison with woody fuels

Directory of Open Access Journals (Sweden)

S. Link

2013-10-01

Full Text Available Reed and coniferous wood can be used for energy production via thermochemical conversion, for instance by gasification. The rate-determining step of the gasification process is the reaction between the char and the gaseous environment in the gasifier, whose rate depends on variables such as pressure, temperature, particle size, mineral matter content, porosity, etc. It is known that reactivity can be improved by increasing the temperature, but on the other hand the temperature achieved in the reactor is limited due to the ash fusion characteristics. Usually, the availability of reed as a fuel is locally modest and, therefore, it must be blended with other fuels such as wood. Blending of fuels brings together several problems relating to ash behaviour, i.e. ash fusion issues. Because there is no correlation between the ash fusion characteristics of biomass blends and their individual components, it is essential to carry out prior laboratory-scale ash fusion tests on the blends. This study compares the reactivity of reed and coniferous wood, and the ash fusion characteristics of blends of reed and coniferous wood ashes. When compared with Douglas fir and reed chars, pine pellets have the highest reactivity. Reed char exhibits the lowest reactivity and, therefore, it is advantageous to gasify reed alone at higher gasification temperatures because the ash fusion temperatures of reed are higher than those of woody fuels. The ash produced by reed and wood blends can melt at lower temperatures than ash from both reed and wood gasified separately. Due to this circumstance the gasification temperature should be chosen carefully when gasification of blends is carried out.

Reactivity and burnout of wood fuels

DEFF Research Database (Denmark)

Dall'Ora, Michelangelo

This thesis deals with the combustion of wood in pulverised fuel power plants. In this type of boiler, the slowest step in the wood conversion process is char combustion, which is one of the factors that not only determine the degree of fuel burnout, but also affect the heat release profile...... of different aspects relevant to wood combustion, including wood structure and composition, wood pyrolysis, wood char properties and wood char oxidation. The full scale campaign, which is the subject of Chapter 3, included sampling of wood fuel before and after milling and sampling of gas and particles...... at the top of the combustion chamber. The collected samples and data are used to obtain an evaluation of the mills in operation at the power plant, the particle size distribution of the wood fuel, as well as the char conversion attained in the furnace. In Chapter 4 an experimental investigation...

Radioactivity of wood ash

International Nuclear Information System (INIS)

Rantavaara, A.; Moring, M.

2000-01-01

STUK (Finnish Radiation and Nuclear Safety Authority) has investigated natural and artificial radioactivity in wood ash and radiation exposure from radionuclides in ash since 1996. The aim was to consider both handling of ash and different ways of using ash. In all 87 ash samples were collected from 22 plants using entirely or partially wood for their energy production in 1996-1997. The sites studied represented mostly chemical forest industry, sawmills or district heat production. Most plants used fluidised bed combustion technique. Samples of both fly ash and bottom ash were studied. The activity concentrations of radionuclides in samples of, e.g., dried fly ash from fuel containing more than 80% wood were determined. The means ranged from 2000 to less than 50 Bq kg -1 , in decreasing order: 137 Cs, 40 K, 90 Sr, 210 Pb, 226 Ra, 232 Th, 134 Cs, 235 U. In bott radionuclide contents decreased in the same order as in fly ash, but were smaller, and 210 Pb was hardly detectable. The NH 4 Ac extractable fractions of activities for isotopes of alkaline elements (K, Cs) in bottom ash were lower than in fly ash, whereas solubility of heavier isotopes was low. Safety requirements defined by STUK in ST-guide 12.2 for handling of peat ash were fulfilled at each of the sites. Use of ash for land-filling and construction of streets was minimal during the sampling period. Increasing this type of ash use had often needed further investigations, as description of the use of additional materials that attenuate radiation. Fertilisation of forests with wood ash adds slightly to the external irradiation in forests, but will mostly decrease doses received through use of timber, berries, mushrooms and game meat. (orig.)

Speciation, behaviour, and fate of mercury under oxy-fuel combustion conditions

International Nuclear Information System (INIS)

Córdoba, Patricia; Maroto-Valer, M.; Delgado, Miguel Angel; Diego, Ruth; Font, Oriol; Querol, Xavier

2016-01-01

The work presented here reports the first study in which the speciation, behaviour and fate of mercury (Hg) have been evaluated under oxy-fuel combustion at the largest oxy-Pulverised Coal Combustion (oxy-PCC) demonstration plant to date during routine operating conditions and partial exhaust flue gas re-circulation to the boiler. The effect of the CO 2 -rich flue gas re-circulation on Hg has also been evaluated. Results reveal that oxy-PCC operational conditions play a significant role on Hg partitioning and fate because of the continuous CO 2 -rich flue gas re-circulations to the boiler. Mercury escapes from the cyclone in a gaseous form as Hg 2+ (68%) and it is the prevalent form in the CO 2 -rich exhaust flue gas (99%) with lower proportions of Hg 0 (1.3%). The overall retention rate for gaseous Hg is around 12%; Hg 0 is more prone to be retained (95%) while Hg 2+ shows a negative efficiency capture for the whole installation. The negative Hg 2+ capture efficiencies are due to the continuous CO 2 -rich exhaust flue gas recirculation to the boiler with enhanced Hg contents. Calculations revealed that 44 mg of Hg were re-circulated to the boiler as a result of 2183 re-circulations of CO 2 -rich flue gas. Especial attention must be paid to the role of the CO 2 -rich exhaust flue gas re-circulation to the boiler on the Hg enrichment in Fly Ashes (FAs). - Highlights: • The fate of gaseous Hg has been evaluated under oxy-fuel combustion. • The Hg oxidation process is enhanced in CO 2 -rich flue gas recirculation. • Hg 2+ is the prevalent gas species in the CO 2 -rich exhaust flue gas. • Hg 2+ (g) shows a negative efficiency capture for the whole installation. • Especial attention must be paid to the Hg enrichment in Fly Ashes.

Speciation, behaviour, and fate of mercury under oxy-fuel combustion conditions

Energy Technology Data Exchange (ETDEWEB)

Córdoba, Patricia, E-mail: pc247@hw.ac.uk [Centre for Innovation on Carbon Capture and Storage (CICCS), Institute of Mechanical, Process and Energy Engineering (IMPEE), Heriot-Watt University, EH14 4AS (United Kingdom); Maroto-Valer, M. [Centre for Innovation on Carbon Capture and Storage (CICCS), Institute of Mechanical, Process and Energy Engineering (IMPEE), Heriot-Watt University, EH14 4AS (United Kingdom); Delgado, Miguel Angel; Diego, Ruth [Fundacion Ciudad de la Energia (CIUDEN), Avenida Segunda, No 2 (Compostilla), 24004 Ponferrada, León (Spain); Font, Oriol; Querol, Xavier [Institute of Environmental Assessment and Water Research (IDÆA-CSIC), Jordi Girona 18-26, E-08034 Barcelona (Spain)

2016-02-15

The work presented here reports the first study in which the speciation, behaviour and fate of mercury (Hg) have been evaluated under oxy-fuel combustion at the largest oxy-Pulverised Coal Combustion (oxy-PCC) demonstration plant to date during routine operating conditions and partial exhaust flue gas re-circulation to the boiler. The effect of the CO{sub 2}-rich flue gas re-circulation on Hg has also been evaluated. Results reveal that oxy-PCC operational conditions play a significant role on Hg partitioning and fate because of the continuous CO{sub 2}-rich flue gas re-circulations to the boiler. Mercury escapes from the cyclone in a gaseous form as Hg{sup 2+} (68%) and it is the prevalent form in the CO{sub 2}-rich exhaust flue gas (99%) with lower proportions of Hg{sup 0} (1.3%). The overall retention rate for gaseous Hg is around 12%; Hg{sup 0} is more prone to be retained (95%) while Hg{sup 2+} shows a negative efficiency capture for the whole installation. The negative Hg{sup 2+} capture efficiencies are due to the continuous CO{sub 2}-rich exhaust flue gas recirculation to the boiler with enhanced Hg contents. Calculations revealed that 44 mg of Hg were re-circulated to the boiler as a result of 2183 re-circulations of CO{sub 2}-rich flue gas. Especial attention must be paid to the role of the CO{sub 2}-rich exhaust flue gas re-circulation to the boiler on the Hg enrichment in Fly Ashes (FAs). - Highlights: • The fate of gaseous Hg has been evaluated under oxy-fuel combustion. • The Hg oxidation process is enhanced in CO{sub 2}-rich flue gas recirculation. • Hg{sup 2+} is the prevalent gas species in the CO{sub 2}-rich exhaust flue gas. • Hg{sup 2+}{sub (g)} shows a negative efficiency capture for the whole installation. • Especial attention must be paid to the Hg enrichment in Fly Ashes.

Coal combustion ashes: A radioactive Waste?

International Nuclear Information System (INIS)

Michetti, F.P.; Tocci, M.

1992-01-01

The radioactive substances naturally hold in fossil fuels, such as Uranium and Thorium, after the combustion, are subjected to an increase of concentration in the residual combustion products as flying ashes or as firebox ashes. A significant percentage of the waste should be classified as radioactive waste, while the political strategies seems to be setted to declassify it as non-radioactive waste. (Author)

Design of a hydraulic ash transport system

Energy Technology Data Exchange (ETDEWEB)

Mirgorodskii, V.G.; Mova, M.E.; Korenev, V.E.; Grechikhin, Yu.A. (Donetskii Politekhnicheskii Institut (USSR))

1990-04-01

Discusses general design of a hydraulic ash removal system to be employed at the reconstructed six 225 MW blocks of the Mironov State Regional Power Plant in the USSR. The blocks burn low-grade solid fuel with an ash content of up to 40.5%. Large quantities of ash have to be moved from the plant (total ash production 60 t/h, using 570 t/h of water for cooling and moistening). An optimum hydraulic ash transportation system would include a two-section airlift pumping system, shown in a diagram. Technological advantages of using this airlift system are enumerated, including short pipes, reduction in required water quantity and the possibility of siting hydraulic pumps at zero level.

Corrosion behavior of Fe-Si metallic coatings added with NiCrAlY in an environment of fuel oil ashes at 700 C

Energy Technology Data Exchange (ETDEWEB)

Salinas-Bravo, V.M.; Porcayo-Calderon, J.; Romero-Castanon, T. [Instituto de Investigaciones Electricas, Gerencia de Procesos Termicos., Av. Reforma 113, C.P. 62490 Col. Palmira. Temixco. Morelos (Mexico); Dominguez-Patino, G.; Gonzalez-Rodriguez, J.G. [U.A.E.M. Centro de Investigaciones en Ingenieria y Ciencias Aplicadas., Av. Universidad 1001, C.P. 62210, Col. Chamilpa. Cuernavaca, Morelos (Mexico)

2005-07-01

Electrochemical potentiodynamic polarization curves and immersion tests for 300 h at 700 C in a furnace have been used to evaluate the corrosion resistance of Fe-Si metallic coatings added with up to 50 wt.% of NiCrAIY. The corrosive environment was fuel oil ashes from a steam generator. The composition of fuel oil ashes includes high content of vanadium, sodium and sulfur. The results obtained show that only the addition of 20 wt.% NiCrAlY to the Fe-Si coating improves its corrosion resistance. The behavior of all tested coatings is explained by the results obtained from the analysis of every coating using electron microscopy and energy dispersive X-ray analysis. (Abstract Copyright [2005], Wiley Periodicals, Inc.)

Diamond drilling for nuclear waste QC

International Nuclear Information System (INIS)

Jennings, Martin.

1990-01-01

Specialised diamond core drilling equipment could soon have a role to play in the safe disposal of intermediate level radioactive waste (ILW). Equipment to core and extract samples for quality checking from cement-filled steel waste drums by techniques compatible with eventual remote-handling operations in a 'hot-cell' is being developed. All coring tests carried out to date have been on simulant waste: 200 litre drums containing mixtures of Ordinary Portland Cement, Ground Granulated Blast Furnace Slag and Pulverised Fuel Ash. No radioactive materials have yet been used for the coring trials. The coring equipment and the diamond coring bits are described. (author)

Life cycle perspective on recycling of ashes; Livscykelperspektiv paa aatervinning av askor

Energy Technology Data Exchange (ETDEWEB)

Olsson, Susanna

2007-07-01

The purpose of this project was to, from a life cycle perspective, discuss the consequences of recycling or disposing combustion ashes. The aim was to regard regional as well as global environmental impacts and point at potential conflicts between different environmental objectives, in order to produce basic information for decision-making on criteria and regulations for ash handling.Three different ashes were studied: bottom ash from waste incineration, fly ash from combustion of peat and from forest fuels. For all ashes three different scenarios were studied, two where the ash is recycled, and one where it is disposed. Focus was put on the difference between the three scenarios during 100 years. The use of bottom ash from waste incineration for roads saved crushed rock and energy, but produced more leaching of metals than the disposal alternative. Using this ash in drainage strata saves sand but causes higher metal leaching too. The same conclusions can be drawn for fly ash from peat, here leaching of Arsenic is the main factor. Using the peat ash as road contraction material saves more resources than the use for drainage blankets. For forest fuel ash, both the use as road construction material and recycling to the forest saves resources and energy. Recycling to the forest saves most energy but also the resources of Zinc, Phosphorous and Dolomite. Leaching of metals is most important for the forest recycling, and the nature of this resource recycling can be argued. The results are most sensitive concerning transports and leaching, but also for maintenance of the constructions where the ash is used. For the forest fuel ash, the suppositions about the necessity of compensation for nutrients removed with the fuel, have important effects for the result. Generally it can be said, for all three cases, that the estimates of leaching of metals are very uncertain, and that there is a need to develop the existing models for long term leaching. The three cases demonstrated

Effect of palm oil fuel ash on compressive strength of palm oil boiler stone lightweight aggregate concrete

Science.gov (United States)

Muthusamy, K.; Zamri, N. A.; Kusbiantoro, A.; Lim, N. H. A. S.; Ariffin, M. A. Mohd

2018-04-01

Both palm oil fuel ash (POFA) and palm oil boiler stone (POBS) are by-products which has been continuously generated by local palm oil mill in large amount. Both by products is usually disposed as profitless waste and considered as nuisance to environment. The present research investigates the workability and compressive strength performance of lightweight aggregate concrete (LWAC) made of palm oil boiler stone (POBS) known as palm oil boiler stone lightweight aggregate concrete (POBS LWAC) containing various content of palm oil fuel ash. The control specimen that is POBS LWAC of grade 60 were produced using 100% OPC. Then, another 4 mixes were prepared by varying the POFA percentage from 10%, 20%, 30% and 40% by weight of cement. Fresh mixes were subjected to slump test to determine its workability before casted in form of cubes. Then, all specimens were subjected to water curing up to 28 days and then tested for its compressive strength. It was found out that utilizing of optimum amount of POFA in POBS LWAC would improve the workability and compressive strength of the concrete. However, inclusion of POFA more than optimum amount is not recommended as it will increase the water demand leading to lower workability and strength reduction.

Adsorption of mercury from aqueous solutions using palm oil fuel ash as an adsorbent - batch studies

Science.gov (United States)

Imla Syafiqah, M. S.; Yussof, H. W.

2018-03-01

Palm oil fuel ash (POFA) is one of the most abundantly produced waste materials. POFA is widely used by the oil palm industry which was collected as ash from the burning of empty fruit bunches fiber (EFB) and palm oil kernel shells (POKS) in the boiler as fuel to generate electricity. Mercury adsorption was conducted in a batch process to study the effects of contact time, initial Hg(II) ion concentration, and temperature. In this study, POFA was prepared and used for the removal of mercury(II) ion from the aqueous phase. The effects of various parameters such as contact time (0- 360 min), temperature (15 – 45 °C) and initial Hg(II) ion concentration (1 – 5 mg/L) for the removal of Hg(II) ion were studied in a batch process. The surface characterization was examined by scanning electron microscopy (SEM) and particle size distribution analysis. From this study, it was found that the highest Hg(II) ion removal was 99.60 % at pH 7, contact time of 4 h, initial Hg(II) ion concentration of 1 mg/L, adsorbent dosage 0.25 g and agitation speed of 100 rpm. The results implied that POFA has the potential as a low-cost and environmental friendly adsorbent for the removal of mercury from aqueous solution.

Ash transformation in suspension fired boilers co-firing coal and straw

DEFF Research Database (Denmark)

Zheng, Yuanjing; Jensen, Peter Arendt; Jensen, Anker Degn

The properties of the ash from co-firing of coal and straw have a large influence on boiler operation, flue gas cleaning equipment and appropriate utilization of the fly ash. A study on the fuel composition and local conditions influence on fly ash properties has been done by making entrained flo...

Microwave based oxidation process for recycling the off-specification (U,Pu)O{sub 2} fuel pellets

Energy Technology Data Exchange (ETDEWEB)

Singh, G., E-mail: gitendars@barctara.gov.in [Advanced Fuel Fabrication Facility (AFFF), Bhabha Atomic Research Centre, Tarapur, 401 502 (India); Khot, P.M. [Advanced Fuel Fabrication Facility (AFFF), Bhabha Atomic Research Centre, Tarapur, 401 502 (India); Kumar, Pradeep [Integrated Fuel Fabrication Facility (IFFF), Bhabha Atomic Research Centre, Mumbai, 400 085 (India); Bhatt, R.B.; Behere, P.G.; Afzal, Mohd [Advanced Fuel Fabrication Facility (AFFF), Bhabha Atomic Research Centre, Tarapur, 401 502 (India)

2017-02-15

This paper reports development of a process named MicroWave Direct Oxidation (MWDO) for recycling the off-specification (U,Pu)O{sub 2} mixed oxide (MOX) fuel pellets generated during fabrication of typical fast reactor fuels. MWDO is a two-stage, single-cycle process based on oxidative pulverisation of pellets using 2450 MHz microwave. The powder sinterability was evaluated by bulk density and BET specific surface area. The oxidised powders were analyzed for phases using XRD and stoichiometry by thermogravimetry. The sinterability was significantly enhanced by carrying out oxidation in higher oxygen partial pressure and by subjecting MOX to multiple micronisation-oxidation cycles. After three cycles, the recycled powder from (U,28%Pu)O{sub 2} resulted surface area >3 m{sup 2}/g and 100% re-used for MOX fabrication. The flow sheet was developed for maximum utilization of recycled powder describable by a parameter called Scrap Recycling Ratio (SRR). The process demonstrates smaller processing cycle, better powder properties and higher oxidative pulverisation over conventional method. - Highlights: • A process for recycling the off-specification (U,Pu)O{sub 2} sintered fuel pellets of fast reactors was demonstrated. • The method is a two-stage, single cycle process based on oxidative pulverization of MOX pellets using 2450 MHz microwave. • The process demonstrated utilization of recycled powder with SRR of 1.

Medium strength self-compacting concrete containing fly ash: Modelling using factorial experimental plans

Energy Technology Data Exchange (ETDEWEB)

Mohammed Sonebi [University of Paisley, Paisley (United Kingdom). Advanced Concrete and Masonry Centre

2004-07-01

This investigation aims to develop medium strength self-compacting concrete (MS-SCC). The cost of materials will be decreased by reducing the cement content and by using pulverised fuel ash (PFA) with a minimum amount of superplasticizer (SP). A factorial design was carried out to mathematically model the influence of five key parameters on filling and passing abilities, segregation and compressive strength, which are important for the successful development of medium strength self-compacting concrete incorporating PFA. The parameters considered in the study were the contents of cement and PFA, water-to-powder (cement+PFA) ratio (W/P) and dosage of SP. The responses of the derived statistical models are slump flow, fluidity loss, Orimet time, V-funnel time, L-box, JRing combined to the Orimet, JRing combined to cone, rheological parameters, segregation and compressive strength at 7, 28 and 90 days. Twenty-one mixes were prepared to derive the statistical models, and five were used for the verification and the accuracy of the developed models. The models are valid for mixes made with 0.38 to 0.72 W/P, 60 to 216 kg/m{sup 3} of cement content, 183 to 317 kg/m{sup 3} of PFA and 0% to 1% of SP, by mass of powder. The influences of W/P, cement and PFA contents, and the dosage of SP were characterised and analysed using polynomial regression, which can identify the primary factors and their interactions on the measured properties. The results show tha MS-SCC can be achieved with a 28-day compressive strength of 30 to 35 MPa by using up to 210 kg/m{sup 3} of PFA.

Synthesis of zeolite from rice husk ash waste of brick industries as hydrophobic adsorbent for fuel grade ethanol purification

Science.gov (United States)

Purnomo, A.; Alhanif, M.; Khotimah, C.; Zuhra, UA; Putri, BR; Kumoro, AC

2017-11-01

A lot of researchers have devoted on ethanol utilization as renewable energy to substitute petroleum based gasoline. When ethanol is being used as a new fuel candidate, it should have at least of 99.5% purity. Usually produced via sugar fermentation process, further purification of ethanol from other components in fermentation broth to obtain its fuel grade is a crucial step. The purpose of this research is to produce synthetic zeolite as hydrophobic adsorbent from rice husk ash for ethanol-water separation and to investigate the influence of weight, adsorption time and initial ethanol concentration on zeolite adsorption capacity. This research consisted of rice husk silica extraction, preparation of hydrophobic zeolite adsorbent, physical characterization using SEM, EDX and adsorption test for an ethanol-water solution. Zeolite with highest adsorption capacity was obtained with 15: 1 alumina silica composition. The best adsorption condition was achieved when 4-gram hydrophobic zeolite applied for adsorption of 100 mL of 10% (v/v) ethanol-water solution for 120 minutes, which resulted in ethanol with 98.93% (v/v) purity. The hydrophobic zeolite from rice husk ash is a potential candidate as an efficient adsorbent to purify raw ethanol into fuel grade ethanol. Implementation of this new adsorbent for ethanol production in commercial scale may reduce the energy consumption of that usually used for the distillation processes.

Characteristic fly-ash particles from oil-shale combustion found in lake sediments

International Nuclear Information System (INIS)

Alliksaar, T.; Hoerstedt, P.; Renberg, I.

1998-01-01

Fly-ash particles accumulate in sediments and can be used to assess spatial distribution and temporal trends of atmospheric deposition of pollutants derived from high temperature combustion of fossil fuels. Previous work has concerned fly-ash derived from oil and coal. Oil-shale is the main fossil fuel used in Estonia and a major source of atmospheric pollution in the Baltic states. To assess if oil-shale power plants produce specific fly-ash particles scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX) were used to compare fly-ash particles from oil-shale combustion with particles from oil and coal combustion. Two types were analysed, large black (10-30μm) and small glassy (< 5 μm) spheroidal particles. Although article morphology to some extent is indicative of the fuel burnt, morphological characters are not sufficient to differentiate between particles of different origin. However, the results indicate that with EDX analysis the fly-ash from oil-shale can be distinguished form oil and coal derived particles in environmental samples. Concentrations of large black and small glassy spheroidal fly-ash particles in a sediment core from an Estonian lake showed similar trends to oil-shale combustion statistics from Estonian power plants. 27 refs., 6 figs., 2 tabs

Ash quality and environmental quality assurance system in co-combustion - Co-combustion of forest industry waste

International Nuclear Information System (INIS)

Laine-Ylijoki, J.; Wahlstroem, M.

2000-01-01

The environmental acceptability and possible utilization of co-combustion ashes will have a significant influence on the wider use of co-combustion in the future. At present the correlation between currently used fuels, their mixture ratios, and quality variations in ashes are not known, which complicates the assessment of possible utilization and environmental acceptability of co-combustion ashes. The composition of ashes has also been found to vary significantly. Effective utilization requires that process variations to alter ash composition and quality variations are known in advance. The aim of the research was to characterize the fly ash from co- combustion of peat, wood and biological paper mill sludge produced under different fuel loadings, especially with and without sludge addition, ant to identify critical parameters influencing on the ash composition. The variations in the leaching properties of ashes collected daily were followed up. The environmental acceptability of the ashes produced under different fuel loadings, especially their suitability for use in road constructions, were evaluated. The project included also the preparation of laboratory reference material from ash material. Guidelines were developed for sampling, sample preparation and analysis, and leaching tests. Furthermore, a quality control system, including sampling strategies, sample analysis and leaching testing, was established

Development of an ash particle deposition model considering build-up and removal mechanisms

Energy Technology Data Exchange (ETDEWEB)

Strandstroem, Kjell; Mueller, Christian; Hupa, Mikko [Aabo Akademi Process Chemistry Centre, Biskopsgatan 8, FI-20500 Aabo (Finland)

2007-12-15

Slagging and fouling on heat exchanger surfaces in power boilers fired with fossil fuels and fuel mixtures has a significant influence on boiler efficiency and availability. Mathematical modelling is since long considered a suitable method to assist boiler operators to determine optimized operating conditions for an existing furnace. The ultimate goal in ash deposition prediction is hereby the determination of the total amount of material deposited and hence the determination of the total reduction in efficiency. Depending on the fuels fired the total deposited mass is a combination of ash particle deposition and ash particle erosion due to non-sticky particles. The novel ash particle deposition model presented in this work considers deposition of sticky ash particles, cleansing of deposit by non-sticky sand particles and sticking of sand due to contact with sticky ash. The steady-state modelling results for the total amount of ash deposited on the deposition probe of an entrained flow reactor presented in this work agree well with the experimental data. Only at very high fractions of sand added as non-sticky material, a significant influence of the sand on the overall mass deposited was found. Since the model considers sticking of non-sticking sand due to contact with sticky ash, the fraction of sand deposited on the probe was especially studied. Using a correction factor to consider the influence of operating time on the steady-state simulations led to good agreement between simulations and experimental data. (author)

Development of an ash particle deposition model considering build-up and removal mechanisms

Energy Technology Data Exchange (ETDEWEB)

Kjell Strandstroem; Christian Muellera; Mikko Hupa [Abo Akademi Process Chemistry Centre, Abo (Finland)

2007-12-15

Slagging and fouling on heat exchanger surfaces in power boilers fired with fossil fuels and fuel mixtures has a significant influence on boiler efficiency and availability. Mathematical modelling has long been considered a suitable method to assist boiler operators to determine optimized operating conditions for an existing furnace. The ultimate goal in ash deposition prediction is hereby the determination of the total amount of material deposited and hence the determination of the total reduction in efficiency. Depending on the fuels fired the total deposited mass is a combination of ash particle deposition and ash particle erosion due to non-sticky particles. The novel ash particle deposition model presented in this work considers deposition of sticky ash particles, cleansing of deposit by non-sticky sand particles and sticking of sand due to contact with sticky ash. The steady-state modelling results for the total amount of ash deposited on the deposition probe of an entrained flow reactor presented in this work agree well with the experimental data. Only at very high fractions of sand added as non-sticky material, a significant influence of the sand on the overall mass deposited was found. Since the model considers sticking of non-sticking sand due to contact with sticky ash, the fraction of sand deposited on the probe was especially studied. Using a correction factor to consider the influence of operating time on the steady-state simulations led to good agreement between simulations and experimental data. 12 refs., 10 figs.

PAHs in leachates from thermal power plant wastes and ash-based construction materials.

Science.gov (United States)

Irha, Natalya; Reinik, Janek; Jefimova, Jekaterina; Koroljova, Arina; Raado, Lembi-Merike; Hain, Tiina; Uibu, Mai; Kuusik, Rein

2015-08-01

The focus of the current study is to characterise the leaching behaviour of polycyclic aromatic hydrocarbons (PAHs) from oil shale ashes (OSAs) of pulverised firing (PF) and circulating fluidised-bed (CFB) boilers from Estonian Thermal Power Plant (Estonia) as well as from mortars and concrete based on OSAs. The target substances were 16 PAHs from the EPA priority pollutant list. OSA samples and OSA-based mortars were tested for leaching, according to European standard EN 12457-2 (2002). European standard CEN/TC 15862(2012) for monolithic matter was used for OSA-based concrete. Water extracts were analysed by GC-MS for the concentration of PAHs. Naphthalene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene and pyrene were detected. Still, the release of PAHs was below the threshold limit value for inert waste. The amount of the finest fraction (particle size materials did not lead to the immobilisation of soluble PAHs. Release of PAHs from the monolith samples did not exceed 0.5 μg/m(2). In terms of leaching of PAHs, OSA is safe to be used for construction purposes.

Ash transformation during co-firing coal and straw

DEFF Research Database (Denmark)

Zheng, Yuanjing; Jensen, Peter Arendt; Jensen, Anker Degn

2007-01-01

Co-firing straw with coal in pulverized fuel boilers can cause problems related to fly ash utilization, deposit formation, corrosion and SCR catalyst deactivation due to the high contents of Cl and K in the ash. To investigate the interaction between coal and straw ash and the effect of coal...... quality on fly ash and deposit properties, straw was co-fired with three kinds of coal in an entrained flow reactor. The compositions of the produced ashes were compared to the available literature data to find suitable scaling parameters that can be used to predict the composition of ash from straw...... and coal co-firing. Reasonable agreement in fly ash compositions regarding total K and fraction of water soluble K was obtained between co-firing in an entrained flow reactor and full-scale plants. Capture of potassium and subsequent release of HCl can be achieved by sulphation with SO2 and more...

A collaborative project on the effects of coal quality on NO{sub x} emissions and carbon burnout in pulverised coal-fired utility boilers

Energy Technology Data Exchange (ETDEWEB)

Tilley, H.A.; O`Connor, M.; Stephenson, P.L.; Whitehouse, M.; Richards, D.G.; Hesselmann, G.; MacPhail, J.; Lockwood, F.C.; Williamson, J.; Williams, A.; Pourkashanian, M. [ETSU, Harwell (United Kingdom)

1998-12-01

This paper describes a UK Department of Trade and Industry-supported collaborative project entitled `The Effects of Coal Quality on Emission of Oxides of Nitrogen (NO{sub x}) and Carbon Burnout in Pulverised Coal-fired Utility Boilers`. The project involved extensive collaboration between the UK power generators, boiler and burner manufacturers and research groups in both industry and academia, together with several of the world`s leading computational fluid dynamics (CFD) `software houses`. The prime objectives of the project were to assess the relationship between NO{sub x} emissions and carbon burnout and to develop and validate predictive tools for assessing coals. Experimental work was carried out on various laboratory-scale apparatus and on single burner test facilities ranging from 160 kW{sub th} to 40 MW{sub th} in size and measurements were obtained from full-scale 500 MW{sub e} utility boiler trials. This data and basic coal data were then used to develop mathematical models to predict full-scale boiler performance with respect to NO{sub x} emissions and carbon-in-ash. Results showed good correlations for NO{sub x} and carbon burnout when comparing data from full-scale and large-scale rig trials. Laboratory-scale tests were found to be useful but the influence of burner aerodynamics was more difficult to quantify. Modelling showed that predicted NO{sub x} emissions were encouragingly close to measured emissions but predicting carbon burnout was less successful. 24 refs., 4 figs., 6 tabs.

Reuse of Partially Sulphated CFBC Ash as an SO2 Sorbent

Energy Technology Data Exchange (ETDEWEB)

Wu, Yinghai; Jia, Lufei; Anthony, E.J. [CanmetENERGY, 1 Haanel Drive, Ottawa, Ontario, K1A1M1 (Canada); Nobili, M.; Telesca, A. [Department of Environmental Engineering and Physics, University of Basilicata, Viale dell' Ateneo, Lucano 10, 85100 Potenza (Italy); Montagnaro, F. [Department of Chemistry, University of Naples ' Federico II' , Monte Sant' Angelo, 80126 Naples (Italy)

2010-06-15

Ashes produced from fluidized bed combustors (FBC) burning high-sulphur fuels often contain 20-30 % unreacted CaO because of the limestone added to remove SO2 in situ. This paper presents the results from experiments into reactivating partially sulphated FBC ash (both bed ash and fly ash) with liquid water, steam and sodium carbonate. The water- or steam-hydrated ashes were subsequently re-sulphated in a thermogravimetric analyzer (TGA) with simulated flue gas. The TGA results show that, while liquid water and steam successfully hydrate and reactivate the unreacted CaO in the bed ash, the treated ashes sulphated to widely different extents. Attempts to reactivate fly ash with hydration failed, although fly ash by itself is extremely reactive. A pilot-scale mini-circulating FBC (CFBC) was also used to evaluate the results of reactivation on the bed ash by hydrating with liquid water and admixtures of inorganic salt (Na2CO3) in the form of either powder or solution. When the treated ash was re-injected into the combustor with the fuel, the effect on SO2 removal efficiency was negligible if Na2CO3 was added as powder. Doping with aqueous solution resulted in enhanced SO2 removal; however, the extent was lower than the level achieved if only water hydration was employed. Increasing the amount of water (from 10% to 30%) to reactivate the ash did not improve the sulphur capture capacity in the mini-CFBC. Overall, this study suggests that the most practical way for re-use of the partially sulphated bed ash as a sulphur sorbent is reactivation by water. A proposal for utilization of the fly ash in an economically reasonable way is also discussed.

Ash fusion temperatures and their association with the transformations of coal ash particles to slag

Energy Technology Data Exchange (ETDEWEB)

Gupta, S.K.; Wall, T.F.; Gupta, R.P. [Cooperative Research Centre for Black Coal Utilisation, Newcastle, NSW (Australia); Creelman, R.A. [Creelman (R.A.) and Associates, Sydney, NSW (Australia)

1997-04-01

Ash deposition on furnace walls in PF (pulverized fuel) furnaces is called slagging when it occurs in the high temperature areas of furnaces directly exposed to flame radiation and fouling in other regions such as tubes in the convection section of the boiler. There are well documented shortcomings of certain approaches relating to their uncertainties as predictive tools for plant performance such as poor repeatability and re-producibility of ash fusion measurements. The nature of physical and chemical changes occurring during melting of coal ash has been investigated in the current study to provide an alternative procedure to the ash fusion test. Shrinkage measurements are frequently used in metallurgy and ceramic science to study the physical properties of materials at high temperatures. The output of this experiment provides three to four `peaks` (maximum rate of shrinkage with temperature) of different intensity and at different temperatures which are related to melting characteristics of the sample. It was concluded that shrinkage extents exceeding 50 percent indicated that the effect of the ash particle size is of secondary importance compared to ash chemistry in determining shrinkage levels, with fine particles giving rapid shrinkage events 10 degrees C lower in temperature. (author). 7 figs., refs.

Potential for thermochemical conversion of biomass residues from the integrated sugar-ethanol process - Fate of ash and ash-forming elements.

Science.gov (United States)

Dirbeba, Meheretu Jaleta; Brink, Anders; DeMartini, Nikolai; Zevenhoven, Maria; Hupa, Mikko

2017-06-01

In this work, potential for thermochemical conversion of biomass residues from an integrated sugar-ethanol process and the fate of ash and ash-forming elements in the process are presented. Ash, ash-forming elements, and energy flows in the process were determined using mass balances and analyses of eight different biomass samples for ash contents, elemental compositions, and heating values. The results show that the ash content increases from the sugarcane to the final residue, vinasse. The cane straw, which is left in the field, contains one-third of the energy and 25% of the K and Cl while the vinasse contains 2% of the energy and 40% of the K and Cl in the cane. K and Cl in biomass fuels cause corrosion and fouling problems in boilers and gasifiers. Over 85% of these elements in the straw are water soluble indicating that water leaching would improve it for utilization in thermochemical conversion. Copyright © 2017 Elsevier Ltd. All rights reserved.

Probe Measurements of Ash Deposit Formation Rate and Shedding in a Biomass Suspension-Fired boiler

DEFF Research Database (Denmark)

Shafique Bashir, Muhammad; Jensen, Peter Arendt; Frandsen, Flemming

The aim of this study was to investigate ash deposit formation rate, heat uptake reduction and deposit removal by using advanced online ash deposition and sootblowing probes in a 350 MWth suspension-fired boiler, utilizing wood and straw pellets as fuel. The influence of fuel type (straw share...

Gas generation in incinerator ash; Gasbildning i aska

Energy Technology Data Exchange (ETDEWEB)

Arm, Maria; Lindeberg, Johanna; Rodin, Aasa; Oehrstroem, Anna; Backman, Rainer; Oehman, Marcus; Bostroem, Dan

2006-02-15

In recent years, explosions have occurred in certain phases of ash handling in Sweden. Investigations have revealed that hydrogen may have been present in all cases. The hydrogen is believed to be generated by chemical reactions of aluminium and other metals within the ash in the presence of water. The purpose with this study is to increase the knowledge of gas generation of incinerator ash. Thereby, guides for appropriate ash management can be introduced and the risk for further explosions prevented. The study has comprised analyses of the ash properties, such as chemical and physical composition and the pH, of ash from 14 incineration plants (mostly waste incineration plants). Different fractions of ash materials representing different parts of the process in each plant have been analysed. Furthermore, the fuel and the technical differences between the plants have been analysed. A tool for measuring the gas generation in the laboratory has been developed and the gas generation of the different ash materials at natural and increased pH was measured. Gas analyses and thermodynamic calculations have also been performed. The results showed that: bottom ash from fluidised bed boilers generated small amounts of gas at increased pH, much smaller amounts than the idle pass, cyclone and filter ash did, bottom ash from grate fired boilers generated more gas at increased pH than their cyclone ash and filter ash, with exception of the Linkoeping plant, all bio waste incineration plants generated ash with low gas generation potential, all fly ash materials with a gas generation potential of more than 10 l/kg originated from municipal waste incineration plants, filter ash that had been stored in oxygen rich environment generated significant less gas than fresh filter ash of the same origin, hardly any other gases were generated apart from hydrogen (very small amounts of acetone, furane, benzene and most likely methane were detected in some of the ash materials), there were no

Regular Recycling of Wood Ash to Prevent Waste Production (RecAsh). Technical Final Report

Energy Technology Data Exchange (ETDEWEB)

Andersson, Lars E-mail: lars.t.andersson@skogsstyreslen.se

2007-03-15

At present, the extraction of harvest residues is predicted to increase in Sweden and Finland. As an effect of the intensified harvesting, the export of nutrients and acid buffering substances from the growth site is also increased. Wood ash could be used to compensate forest soils for such losses. Most wood fuel ash is today often deposited in landfills. If the wood ash is recycled, wood energy is produced without any significant waste production. Ash recycling would therefore contribute to decreasing the production of waste, and to maintaining the chemical quality of forest waters and biological productivity of forest soils in the long term. The project has developed, analysed and demonstrated two regular ash-recycling systems. It has also distributed knowledge gathered about motives for ash recycling as well as technical and administrative solutions through a range of media (handbooks, workshops, field demonstrations, reports, web page and information videos). Hopefully, the project will contribute to decreasing waste problems related to bio-energy production in the EU at large. The project has been organised as a separate structure at the beneficiary and divided in four geographically defined subprojects, one in Finland and three in Sweden (Central Sweden, Northern Sweden, and South-western Sweden). The work in each subproject has been lead by a subproject leader. Each subproject has organised a regional reference group. A project steering committee has been established consisting of senior officials from all concerned partners. The project had nine main tasks with the following main expected deliverables and output: 1. Development of two complete full-scale ash-recycling systems; 2. Production of handbooks of the ash recycling system; 3. Ash classification study to support national actions for recommendations; 4. Organise regional demonstrations of various technical options for ash treatment and spreading; 5. Organise national seminars and demonstrations of

BRICKS WITH TOTAL REPLACEMENT OF CLAY BY FLY ASH MIXED WITH DIFFERENT MATERIALS

OpenAIRE

J.N Akhtar; J.Alam; M.N Akhtar

2011-01-01

Fly ash is a powdery substance obtained from the dust collectors in the Thermal power plants that use coal as fuel. From the cement point of view the mineralogy of Fly ash is important as it contains 80% - 90% of glass. The impurities in coal-mostly clays, shale’s, limestone & dolomite; they cannot be burned so they turn up as ash. The Fly ash of class C category was used as a raw material to total replacement of clay for making Fly ash bricks. In present study the effect of Fly ash with high...

Radioactivity of wood ash; Puun tuhkan radioaktiivisuus

Energy Technology Data Exchange (ETDEWEB)

Rantavaara, A.; Moring, M

2000-01-01

STUK (Finnish Radiation and Nuclear Safety Authority) has investigated natural and artificial radioactivity in wood ash and radiation exposure from radionuclides in ash since 1996. The aim was to consider both handling of ash and different ways of using ash. In all 87 ash samples were collected from 22 plants using entirely or partially wood for their energy production in 1996-1997. The sites studied represented mostly chemical forest industry, sawmills or district heat production. Most plants used fluidised bed combustion technique. Samples of both fly ash and bottom ash were studied. The activity concentrations of radionuclides in samples of, e.g., dried fly ash from fuel containing more than 80% wood were determined. The means ranged from 2000 to less than 50 Bq kg{sup -1}, in decreasing order: {sup 137}Cs, {sup 40}K, {sup 90}Sr, {sup 210}Pb,{sup 226}Ra, {sup 232}Th, {sup 134}Cs, {sup 235}U. In bott radionuclide contents decreased in the same order as in fly ash, but were smaller, and {sup 210}Pb was hardly detectable. The NH{sub 4}Ac extractable fractions of activities for isotopes of alkaline elements (K, Cs) in bottom ash were lower than in fly ash, whereas solubility of heavier isotopes was low. Safety requirements defined by STUK in ST-guide 12.2 for handling of peat ash were fulfilled at each of the sites. Use of ash for land-filling and construction of streets was minimal during the sampling period. Increasing this type of ash use had often needed further investigations, as description of the use of additional materials that attenuate radiation. Fertilisation of forests with wood ash adds slightly to the external irradiation in forests, but will mostly decrease doses received through use of timber, berries, mushrooms and game meat. (orig.)

Quantification of Ash Deposit Build-up and Removal in a Straw and Wood Suspension-Fired Boiler

DEFF Research Database (Denmark)

Shafique Bashir, Muhammad; Jensen, Peter Arendt; Frandsen, Flemming

2011-01-01

The aim of this study was to investigate ash deposit formation rate, heat uptake reduction and deposit removal by using advanced online ash deposition and sootblowing probes in a 350 MWth suspension­fired boiler, utilizing wood and straw pellets as fuel. The influence of fuel type (straw share...

Evaluation of different pulverisation methods for RNA extraction in squash fruit: lyophilisation, cryogenic mill and mortar grinding.

Science.gov (United States)

Román, Belén; González-Verdejo, Clara I; Peña, Francisco; Nadal, Salvador; Gómez, Pedro

2012-01-01

Quality and integrity of RNA are critical for transcription studies in plant molecular biology. In squash fruit and other high water content crops, the grinding of tissue with mortar and pestle in liquid nitrogen fails to produce a homogeneous and fine powered sample desirable to ensure a good penetration of the extraction reagent. To develop an improved pulverisation method to facilitate the homogenisation process of squash fruit tissue prior to RNA extraction without reducing quality and yield of the extracted RNA. Three methods of pulverisation, each followed by the same extraction protocol, were compared. The first approach consisted of the lyophilisation of the sample in order to remove the excess of water before grinding, the second one used a cryogenic mill and the control one a mortar grinding of frozen tissue. The quality of the isolated RNA was tested by carrying out a quantitative real time downstream amplification. In the three situations considered, mean values for A(260) /A(280) indicated minimal interference by proteins and RNA quality indicator (RQI) values were considered appropriate for quantitative real-time polymerase chain reaction (qRT-PCR) amplification. Successful qRT-PCR amplifications were obtained with cDNA isolated with the three protocols. Both apparatus can improve and facilitate the grinding step in the RNA extraction process in zucchini, resulting in isolated RNA of high quality and integrity as revealed by qRT-PCR downstream application. This is apparently the first time that a cryogenic mill has been used to prepare fruit samples for RNA extraction, thereby improving the sampling strategy because the fine powder obtained represents a homogeneous mix of the organ tissue. Copyright © 2012 John Wiley & Sons, Ltd.

Rheology of fly ashes from coal and biomass co-combustion

DEFF Research Database (Denmark)

Arvelakis, Stelios; Frandsen, Flemming

2010-01-01

The presence of large amounts of alkali metals, chlorine and sulphur in most biomass fuels - compared to coal - can create serious ash-related problems such as deposition, agglomeration and/or corrosion. This paper discusses the viscosity characteristics of fly ash from the co-combustion of various...... coal/biomass blends in a pilot scale pf-boiler. The produced data provide information on the melting of the ash and its flow characteristics, as a function of temperature, which may be used to modify the temperature profile of the boiler in order to avoid slagging. Straw co-firing lowers the ash...... viscosity leading to higher stickiness of the ash particles. Wood co-firing has only minor effects, due to the composition of wood ash and the low percentage of wood in the coal/biomass blend....

Autothermal gasification of low-grade fuels in fluidized bed

Energy Technology Data Exchange (ETDEWEB)

A.A. Belyaev [Scientific Center for Comprehensive Processing of Solid Combustible Minerals (IGI), Moscow (Russian Federation). Institute of Combustible Minerals Federal State Unitary Enterprise

2009-01-15

Autothermal gasification of high-ash flotation wastes of Grade Zh Kuzbass coal and low-ash fuel in a suspended-spouted (fluidized) bed at atmospheric pressure is investigated, and a comparison is presented of experimental results that indicate that the ash content of fuels has only slight influence on the generator gas heating value.

Utilization of ash fractions from alternative biofuels used in power plants

Energy Technology Data Exchange (ETDEWEB)

Nikolaisen, L.; Hinge, J.; Christensen, I. (Danish Technological Inst., Aarhus (Denmark)); Dahl, J. (Force Technology, Broendby (Denmark)); Arendt Jensen, P. (DTU-CHEC, Kgs. Lyngby (Denmark)); Soendergaard Birkmose, T. (Dansk Landbrugsraadgivning, Landscentret, Aarhus (Denmark)); Sander, B. (DONG Energy, Fredericia (Denmark)); Kristensen, O. (Kommunekemi A/S, Nyborg (Denmark))

2008-07-15

It is expected, that demand for the traditional biomass resources wood and straw will increase over the next years. In other projects a number of agro industrial waste products has been tested and characterized as fuels for power plants. The annual production in Denmark of these fuels is estimated at roughly 400.000 tons of Dry Matter per year, so the potential is substantial. The agro industrial biomass products include: Grain screening waste, pea shells, soy waste, cocoa waste, sugar beet waste, sunflower waste, shea waste, coffee waste, olive waste, rice shell waste, potato waste, pectin waste, carrageen waste, tobacco waste, rape seed waste and mash from breweries. In the PSO project 5075, 5 different types of fuel pellets was produced, which were rendered suitable for combustion in power plants. In this project, ash is produced from the above mentioned 5 mixtures together with another 2 mixtures produced especially for this project. From the 5 mixtures from PSO 5075, ash is produced at Danish Technological Institute's slag analyzer. These ash products are rendered comparable to ash from grate fired boilers at power plants. The ash/slag from the combustion in the slag analyzer was then grinded - thus resulting in a total of 5 ash products. At DTU CHEC's Entrained Flow Reactor, ash products from the 5+2 mixtures were produced. These ash products are rendered comparable to ash produced form suspension fired boilers at power plants. For each of the 7 mixtures, bottom-, cyclone and filter ash was taken out separately resulting in a total of 21 ash samples. The produced ashes have been evaluated for their properties as directly applied fertilizer. Furthermore, scenarios have been set up to assess the feasibility in producing artificial fertilizer from the ash products, based on known processes. In the main components the content of Na, S, Cl and K is significantly higher in filter ashes, whereas the content of Mg, Al, Si and Ca is significantly lower. The

Deposit Probe Measurements in Danish Grate and Pulverized Fuel Biomass Power Boilers

DEFF Research Database (Denmark)

Hansen, Stine Broholm; Jensen, Peter Arendt; Jappe Frandsen, Flemming

2012-01-01

. Corresponding samples of fuels, ash deposits and fly ash have provided information on the transformation of inorganics in the boiler. Generally, grate fired boilers provide a fly ash containing high contents of K, Cl and S compared to the fuel ash, while suspension fired boilers fly ash has a composition nearly...... similar to the fuel ash. Inner most biomass deposits are always salt-rich, while thicker deposit layers also contain some Si and Ca. Deposit probe formation rate measurements have been performed in different ways on several boilers. Grate and suspension fired boilers seems to cause similar deposit...... formation rates. Suspension fired boilers generate more fly ash, while grate boilers form a fly ash with a higher fraction of melt formation (and thereby a higher sticking probability) at similar temperatures. For suspension fired units it is observed that wood with a lower ash content than straw gives rise...

Beneficial use of CFB ash in pavement construction applications

Energy Technology Data Exchange (ETDEWEB)

N. Mike Jackson; Scott Schultz; Paul Sander; Lindsay Schopp [Jackson Research Engineers, Inc., Ponte Vedra Beach, FL (United States)

2009-07-15

The disposal of ash produced from the combustion of solid fuels has been a major subject of research and product development for many years. An innovative application has recently been employed by JEA to recycle both the bottom ash and fly ash from two new circulating fluidized bed (CFB) boilers as a stabilizer for local sandy soils and pavement base course material. The results of laboratory testing and field applications in the north Florida market area illustrate how this by-product is adding value in pavement and roadway construction applications. 14 refs., 2 figs., 10 tabs.

Ash behavior and de-fluidization in low temperature circulating fluidized bed biomass gasifier

DEFF Research Database (Denmark)

Narayan, Vikas

ensures that high-alkali biomass fuels can be used without risks of bed de-fluidization. This thesis aims to understand the behavior of alkali metals and ash in the LTCFB system. The thesis work involved measurements made on bed material and product gas dust samples on a 100kW LTCFB gasifier placed......Biomass is increasingly used as a fuel for power generation. Herbaceous fuels however, contain high amounts of alkali metals which get volatilized at high temperatures and forms salts with low melting points and thus condense on pipelines, reactor surfaces and may cause de-fluidization. A Low......-Temperature Circulating Fluidized Bed System (LTCFB) gasifier allows pyrolysis and gasification of biomass to occur at low temperatures thereby improving the retention of alkali and other ash species within the system and minimizing the amount of ash species in the product gas. In addition, the low reactor temperature...

The behavior of ash species in suspension fired biomass boilers

DEFF Research Database (Denmark)

Jensen, Peter Arendt

While fluid bed and grate fired boilers initially was the choice of boilers used for power production from both wood and herbaceous biomass, in recent years suspension fired boilers have been increasingly used for biomass based power production. In Denmark several large pulverized fuel boilers have...... been converted from coal to biomass combustion in the last 15 years. This have included co-firing of coal and straw, up to 100% firing of wood or straw andthe use of coal ash as an additive to remedy problems with wood firing. In parallel to the commercialization of the pulverized biomass firing...... technology a long range of research studies have been conducted, to improve our understanding of the influence and behavior of biomass ash species in suspension fired boilers. The fuel ash plays a key role with respect tooptimal boiler operation and influences phenomena’s as boiler chamber deposit formation...

Possibilities and evaluation of straw pretreatment

DEFF Research Database (Denmark)

Knudsen, Niels Ole; Jensen, Peter Arendt; Sander, Bo

1998-01-01

Biomass utilisation by cofiring of straw in a pulverised coal fire boiler is economically attractive compared to dedicated straw fired plants. However, the high content of potassium and chloride impedes utilisation of the fly ash, deactivates the de NOx catalysts in the flue gas cleaning system...

Influence of palm oil fuel ash on fresh and mechanical properties of ...

Indian Academy of Sciences (India)

percentage of cement, with several supplementary cementitious materials (SCM) such as silica fume, ground granulated blast-furnace slag, fly ash and rice husk ash ..... Safiuddin M, West J and Soudki K 2011b Flowing ability of the mortars ...

Environmentally friendly use of non-coal ashes in Sweden.

Science.gov (United States)

Ribbing, C

2007-01-01

The Swedish Thermal Engineering Research Institute (Värmeforsk) initiated an applied research program "Environmentally friendly use of non-coal ashes", in 2002. The program aims at increasing knowledge on the by-products of energy production and their application. The goal of formulating technical and environmental guidelines and assessments is a major point of the program, which is supported by about forty authorities and private organisations. The programme has been divided into four areas: recycling of ashes to forests, geotechnical applications, use in landfilling, and environmental aspects and chemistry. Among all results obtained, the following progress is shown: *Evidence for the positive effects of spreading ashes on forest growth. *A proposal for environmental guidelines on the utilisation of ashes in construction. *A handbook for using non-coal fly ashes in unpaved roads. *Technical and environmental assessments of MSWI bottom ashes in road construction. *Development of the use of ashes with municipal wastewater sludge as a cover for landfills and mine tailings. *Use of ashes from bio-fuels in concrete and replacement of cement in stoop mining. *A method to classify those by-products from combustion that have mirror entries in the EWC as a hazardous or non-hazardous compound. The Ash Programme has also made it possible to increase knowledge on ashes as valuable materials, on quality assurance and on markets for recovered materials.

Evaluation of wood residues from Crete as alternative fuels

Energy Technology Data Exchange (ETDEWEB)

Vamvuka, D. [Department of Mineral Resources Engineering, Technical University of Crete (Greece); Bandelis, G. [Professional School of Chania, EPAS Chania (Greece)

2010-07-01

Olive and citrus prunings, the main agricultural residues of Crete, are considered to be of premium importance for local energy production, substituting a large part of conventional fuels. The thermal behaviour of these fuels during combustion was studied by thermogravimetry, at non-isothermal heating conditions. Fly ashes were collected from tests in a lab-scale fluidized bed facility. The effect of the inorganic constituents of the fuels on slagging/fouling and agglomeration propensities, as well as environmental pollution was examined. Kinetic models were developed and reaction rates were determined. The agroresidues studied were characterized as good quality fuels, having high volatile and low ash and sulphur contents. Their ash was rich in Ca, Si, K and P minerals. However, fly ashes were poorer in alkali compounds, implying lower deposition and corrosion problems in boilers. The environmental impact of heavy metals is negligible. The thermochemical reactivity of the two fuels in air was very similar. A power low model fitted the experimental results accurately.

Utilization of stabilized municipal waste combustion ash residues as construction material

International Nuclear Information System (INIS)

Shieh, C.S.

1992-01-01

Stabilized municipal waste combustion (MWC) ash residues were investigated for their potential as construction material that can be beneficially used in terrestrial and marine environments. End-use products, such as patio stones, brick pavers, solid blocks, and reef units, were fabricated and tested for their engineering and chemical characteristics. engineering feasibility and environmental acceptability of using stabilized ash residues as construction material are discussed in this paper. Ash samples were collected from two mass-burn facilities and one refuse derived fuel (RDF) facility in Florida

Characterization of ashes from biofuels

Energy Technology Data Exchange (ETDEWEB)

Frandsen, F.J.; Hansen, L.A. [Technical Univ. of Denmark. Dept. of Chemical Engineering (Denmark); Soerensen, H.S. [Geological Survey of Denmark and Greenland (Denmark); Hjuler, K. [dk-TEKNIK. Energy and Environment (Denmark)

1998-02-01

One motivation for initiating the present project was that the international standard method of estimating the deposit propensity of solid fuels, of which a number of variants exist (e.g. ISO, ASTM, SD, DIN), has shown to be unsuitable for biomass ashes. This goal was addressed by the development of two new methods for the detection of ash fusibility behaviour based on Simultaneous Thermal Analysis (STA) and High Temperature Light Microscopy (HTLM), respectively. The methods were developed specifically for ashes from biofuels, but are suitable for coal ashes as well. They have been tested using simple salt mixtures, geological standards and samples from straw CHP and coal-straw PF combustion plants. All samples were run in a nitrogen atmosphere at a heating rate of 10 deg. C/min. In comparison with the standard method, the new methods are objective and have superior repeatability and sensitivity. Furthermore, the two methods enable the melting behavior to be characterized by a continuous measurement of melt fraction versus temperature. Due to this two-dimensional resolution of the results, the STA and HTLM methods provide more information than the standard method. The study of bottom ash and fly ash as well as deposit samples from straw test firings at the Haslev and Slagelse Combined Heat and Power plants resulted in a better understanding of mineral behaviour during straw grate firing. In these tests a number of straws were fired which had been carefully selected for having different qualities with respect to sort and potassium and chlorine contents. By studying bottom ashes from Slagelse it was found that the melting behaviour correlated with the deposition rate on a probe situated at the outlet part of the combustion zone. (EG)

Effect of unground oil palm ash as mixing ingredient towards properties of concrete

Science.gov (United States)

Sulaiman, M. A.; Muthusamy, K.; Mat Aris, S.; Rasid, M. H. Mohd; Paramasivam, R.; Othman, R.

2018-04-01

Malaysia being one of the world largest palm oil producers generates palm oil fuel ash (POFA), a by-product in increasing quantity. This material which usually disposed as solid waste causes pollution to the environment. Success in converting this waste material into benefitting product would reduce amount of waste disposed and contributes towards cleaner environment. This research explores the potential of unground oil palm ash being used as partial sand replacement in normal concrete production. Experimental work has been conducted to determine the workability, compressive strength and flexural strength of concrete when unground oil palm ash is added as partial sand replacement. A total of five mixes containing various percentage of oil palm ash, which are 0%, 5%, 10%, 15% and 20% have been prepared. All specimens were water cured until the testing date. The slump test, compressive strength test and flexural strength test was conducted. The findings show that mix produced using 10% of palm oil fuel ash exhibit higher compressive strength and flexural strength as compared to control specimen. Utilization of unground oil palm ash as partial sand replacement would be able to reduce dependency of construction industry on natural sand supply and also as one of the solution to reuse palm oil industry waste.

Comparison of coal/solid recovered fuel (SRF) with coal/refuse derived fuel (RDF) in a fluidised bed reactor

International Nuclear Information System (INIS)

Wagland, S.T.; Kilgallon, P.; Coveney, R.; Garg, A.; Smith, R.; Longhurst, P.J.; Pollard, S.J.T.; Simms, N.

2011-01-01

An experimental study was undertaken to compare the differences between municipal solid waste (MSW) derived solid recovered fuel (SRF) (complying with CEN standards) and refuse derived fuel (RDF). Both fuels were co-combusted with coal in a 50 kW fluidised bed combustor and the metal emissions were compared. Synthetic SRF was prepared in the laboratory by grinding major constituents of MSW such as paper, plastic, textile and wood. RDF was obtained from a local mechanical treatment plant. Heavy metal emissions in flue gas and ash samples from the (coal + 10% SRF) fuel mixture were found to be within the acceptable range and were generally lower than that obtained for coal + 10% RDF fuel mixture. The relative distribution of heavy metals in ash components and the flue gas stream shows the presence of a large fraction (up to 98%) of most of the metals in the ash (except Hg and As). Thermo-gravimetric (TG) analysis of SRF constituents was performed to understand the behaviour of fuel mixtures in the absence and presence of air. The results obtained from the experimental study will enhance the confidence of fuel users towards using MSW-derived SRF as an alternative fuel.

A Comprehensive Review on the Properties of Coal Bottom Ash in Concrete as Sound Absorption Material

OpenAIRE

Ramzi Hannan Nurul Izzati Raihan; Shahidan Shahiron; Ali Noorwirdawati; Maarof Mohamad Zulkhairi

2017-01-01

The government is currently implementing policies to increase the usage of coal as fuel for electricity generation. At the same time, the dependency on gas will be reduced. In addition, coal power plants in Malaysia produce large amounts of industrial waste such as bottom ash which is collected in impoundment ponds (ash pond). However, millions of tons of coal ash (bottom ash) waste are collected in ponds near power plant stations. Since bottom ash has been classified as hazardous material th...

ERA-Net Evaluation of technology status for small-scale combustion of pellets from new ash rich biomasses - combustion tests in residential burners

Energy Technology Data Exchange (ETDEWEB)

Roennbaeck, Marie; Johansson, Mathias; Frida Claesson

2008-07-01

In this project, pellets with higher ash content compared to the wood pellets used today on the Swedish market were tested in three domestic-scale burners. The tests were carried out based on EN 303-5. In the flue gas, combustion parameters as carbon monoxide, carbon dioxide, oxygen and hydro carbons were measured, and also more fuel specific parameters such as nitrogen oxides, sulphur dioxide, hydrogen chloride, total dust and particle mass- and number concentration. The dust (fly ash) and bottom ash were characterized chemically. The implications of high ash content on combustion performance are discussed in the report. Altogether five pellets with 8 mm diameter were tested: oilseed straw pellet, reed canary grass pellet (RCG), barley straw pellet, bark pellet and wood pellet. All fuels were dry ranging from 6.5-12 % moisture. The ash content varied from 0.3 weight-% dm in wood to 7.9 % in RCG. Barley straw has a noticeable low ash melting temperature, < 980 deg C, and could not be combusted in any of the burners. The nitrogen content varied nine times and sulphur more than 10 times. The chlorine content was very low in wood and bark and more than 20 times higher in oilseed and barley. The composition of inorganic species in the fuel ash was dominated by calcium, potassium and silica in wood, bark and oilseed pellet, while RCG and barley straw were dominated by silica. The three burners used were commercial and known to fulfil high quality requirements. Burner A is a pellet burner where fuel is supplied on top of the grate with no mechanical mean for moving bottom ash on the grate during combustion. Bottom ash is blown away, and any slag remaining on the grate is removed with a scrape before ignition. Burner B is an upward burning pellet burner where fuel and ash is pushed upwards and the glow bed is exposed to the surrounding combustion department. Burner C is a forward burning grain burner that pushes fuel and ash forwards, inside a cylinder. From the

Ash and heavy metals in fluidized bed-combustion; Tuhka ja raskasmetallit puuperaeisen jaetteen kerrosleijupoltossa

Energy Technology Data Exchange (ETDEWEB)

Kaessi, T.; Aittoniemi, P. [IVO International, Vantaa (Finland)

1996-12-01

Combustion ashes and submicron fly ash particles were characterized in two industrial boilers (bubbling vs. circulating fluidized bed) burning paper mill deinking sludge and bark or wood as support fuel. Bulk samples from fly ash, circulating ash and bottom ash were analyzed. Fine particles in fly ash were monitored and sampled for microscopic studies. The mass size distribution of fly ash was measured and the chemical composition according to particle size was analyzed. The results showed that ash consists of large and friable clusters formed by sintering of small mineral particles originating from paper fillers. Very few ash particles were fused and they were found only among the smallest particles. No agglomerates of fused particles were found. If the residence time in furnace is long enough sintering may proceed further and ash structure grows more dense. No indication of ash vaporization was detected. These results were similar for bubbling and circulating fluidized bed boilers. (author)

Partial oxidation of methane to methanol over catalyst ZSM-5 from coal fly ash and rice husk ash

Directory of Open Access Journals (Sweden)

Mirda Yanti Fusia

2017-01-01

Full Text Available Methane is one of the greenhouse gases that can be converted into liquid fuels such as methanol to retain most of the energy of methane and produce a cleaner environment. The conversion of methane to methanol using ZMS-5 represents a breakthrough in the utilization of methane. However, material sources for zeolite synthesis as catalyst usually are pro-analysis grade materials, which are expensive. Therefore, in this research, coal fly ash and rice husk ash were used as raw materials for mesoporous ZSM-5 zeolite synthesis. First, coal fly ash and rice husk were subjected to pre-treatment to extract silicate (SiO44− and aluminate (AlO45− and impurities separation. The ZSM-5 zeolite was synthesized through hydrothermal treatment using two types of templates. After ZSM-5 was synthesized, it was modified with Cobalt through impregnation method. The catalytic activity of both ZSM-5 and Co/ZSM-5 zeolites as heterogeneous catalysts in partial oxidation of methane were preliminary tested and compared with that commercial one. The result showed that the zeolite catalyst ZSM-5 from fly ash coal and rice husk ash has the potential to be used as catalysts in the partial oxidation of methane to methanol.

Synthesis of cracked Calophyllum inophyllum oil using fly ash catalyst for diesel engine application

KAUST Repository

Muthukumaran, N.

2015-04-16

In this study, production of hydrocarbon fuel from Calophyllum inophyllum oil has been characterized for diesel engine application, by appraising essential fuel processing parameters. As opposed to traditional trans-esterification process, the reported oil was cracked using a catalyst, as the latter improves the fuel properties better than the former. In a bid to make the production process economically viable, a waste and cheap catalyst, RFA (raw fly ash), has been capitalized for the cracking process as against the conventional zeolite catalyst. The fuel production process, which is performed in a fixed bed catalytic reactor, was done methodologically after comprehensively studying the characteristics of fly ash catalyst. Significantly, fly ash characterization was realized using SEM and EDS, which demarcated the surface and internal structures of fly ash particles before and after cracking. After the production of hydrocarbon fuel from C. inophyllum oil, the performed compositional analysis in GC-MS revealed the presence of esters, parfins and olefins. Followed by the characterization of catalytically cracked C. inophyllum oil, suitable blends of it with diesel were tested in a single cylinder diesel engine. From the engine experimental results, BTE (brake thermal efficiency) of the engine for B25 (25% cracked C. inophyllum oil and 75% diesel) was observed to be closer to diesel, while it decreased for higher blends. On the other hand, emissions such as HC (hydrocarbon), CO (carbon monoxide) and smoke were found to be comparable for B25 with diesel. © 2015 Elsevier Ltd. All rights reserved.

Ash properties of some dominant Greek forest species

International Nuclear Information System (INIS)

Liodakis, S.; Katsigiannis, G.; Kakali, G.

2005-01-01

The elemental and chemical wood ash compositions of six dominant Greek fuels was investigated using a variety of techniques, including thermal gravimetric analysis (TG), differential thermal analysis (DTA), atomic absorption spectroscopy (AAS) and X-ray diffraction (XRD). In addition, the alkalinity of wood ash was determined by titration. The ash was prepared by combustion at low (600 deg. C), middle (800 deg. C) and high temperatures (1000 deg. C). The ash composition is very important because thousands of hectares of wildlands are burned annually in Greece. The resulting deposits affect soil properties (i.e., pH) and provide a source of inorganic constituents (i.e., Ca, K, Na, Mg, etc.), while the most soluble compounds (i.e., sodium and potassium hydroxides and carbonates) do not persist through the wet season. The samples selected were: Pinus halepensis (Aleppo pine), Pinus brutia (Calabrian pine), Olea europaea (Olive), Cupressus sempervirens (Italian cypress), Pistacia lentiscus (Mastic tree), Quercus coccifera (Holly oak)

Ash properties of some dominant Greek forest species

Energy Technology Data Exchange (ETDEWEB)

Liodakis, S. [Laboratory of Inorganic and Analytical Chemistry, Department of Chemical Engineering, National Technical University of Athens (NTUA), 9 Iroon Polytechniou Street, Athens 157 73 (Greece)]. E-mail: liodakis@central.ntua.gr; Katsigiannis, G. [Laboratory of Inorganic and Analytical Chemistry, Department of Chemical Engineering, National Technical University of Athens (NTUA), 9 Iroon Polytechniou Street, Athens 157 73 (Greece); Kakali, G. [Laboratory of Inorganic and Analytical Chemistry, Department of Chemical Engineering, National Technical University of Athens (NTUA), 9 Iroon Polytechniou Street, Athens 157 73 (Greece)

2005-10-15

The elemental and chemical wood ash compositions of six dominant Greek fuels was investigated using a variety of techniques, including thermal gravimetric analysis (TG), differential thermal analysis (DTA), atomic absorption spectroscopy (AAS) and X-ray diffraction (XRD). In addition, the alkalinity of wood ash was determined by titration. The ash was prepared by combustion at low (600 deg. C), middle (800 deg. C) and high temperatures (1000 deg. C). The ash composition is very important because thousands of hectares of wildlands are burned annually in Greece. The resulting deposits affect soil properties (i.e., pH) and provide a source of inorganic constituents (i.e., Ca, K, Na, Mg, etc.), while the most soluble compounds (i.e., sodium and potassium hydroxides and carbonates) do not persist through the wet season. The samples selected were: Pinus halepensis (Aleppo pine), Pinus brutia (Calabrian pine), Olea europaea (Olive), Cupressus sempervirens (Italian cypress), Pistacia lentiscus (Mastic tree), Quercus coccifera (Holly oak)

Speciation, behaviour, and fate of mercury under oxy-fuel combustion conditions.

Science.gov (United States)

Córdoba, Patricia; Maroto-Valer, M; Delgado, Miguel Angel; Diego, Ruth; Font, Oriol; Querol, Xavier

2016-02-01

The work presented here reports the first study in which the speciation, behaviour and fate of mercury (Hg) have been evaluated under oxy-fuel combustion at the largest oxy-Pulverised Coal Combustion (oxy-PCC) demonstration plant to date during routine operating conditions and partial exhaust flue gas re-circulation to the boiler. The effect of the CO2-rich flue gas re-circulation on Hg has also been evaluated. Results reveal that oxy-PCC operational conditions play a significant role on Hg partitioning and fate because of the continuous CO2-rich flue gas re-circulations to the boiler. Mercury escapes from the cyclone in a gaseous form as Hg(2+) (68%) and it is the prevalent form in the CO2-rich exhaust flue gas (99%) with lower proportions of Hg(0) (1.3%). The overall retention rate for gaseous Hg is around 12%; Hg(0) is more prone to be retained (95%) while Hg(2+) shows a negative efficiency capture for the whole installation. The negative Hg(2+) capture efficiencies are due to the continuous CO2-rich exhaust flue gas recirculation to the boiler with enhanced Hg contents. Calculations revealed that 44mg of Hg were re-circulated to the boiler as a result of 2183 re-circulations of CO2-rich flue gas. Especial attention must be paid to the role of the CO2-rich exhaust flue gas re-circulation to the boiler on the Hg enrichment in Fly Ashes (FAs). Copyright © 2015 Elsevier Inc. All rights reserved.

Bottom ash from fluidising bed boilers as filler material in district heating pipe culverts. Chemical and geotechnical characterisation; Pannsand som kringfyllnadsmaterial foer fjaerrvaermeroergravar. Kemisk och geoteknisk karaktaerisering av fluidbaeddsand

Energy Technology Data Exchange (ETDEWEB)

Pettersson, Roger; Rogbeck, Jan; Suer, Pascal

2004-01-01

Bottom ashes from fluid bed boilers have been characterised, both geotechnically and chemically, in order to investigate the possibility to use them as filler material in district heating pipe culverts. Bottom ashes from both biofuel boilers and waste boilers are represented in this project. The companies which ashes have been characterised are Sundsvall Energi AB, Sydkraft OestVaerme AB, Sydkraft MaelarVaerme AB, Eskilstuna Miljoe och Energi, Stora Enso Fors, Soederenergi and Fortum Vaerme. A total of ten ashes have been analysed where three ashes originates from Sundsvall Energi AB, two from Sydkraft OestVaerme AB and one from the each of the remaining companies. The chemical analyses have been performed both on fresh ashes and on ashes aged for three months. The geotechnical analyses performed are grain size distribution, packing abilities and permeability. Chemical analyses performed are total content, available content, leaching tests (leaching both by shaking method and column procedure) and organic analyses (PAH, EOX, TOC, dioxin and fenol). The geotechnical analyses show that the ashes fulfils the demands that are put on the filler material used in district heating pipe culverts. When using the ashes in applications, light compaction should be performed due to the risk of crushing the material which may cause an increased amount of fine material. The leachability of fine material is larger than for coarse material. The ashes are relatively insensitive to precipitation. Bio fuel based bottom ashes have a lower content of environmental affecting substances than waste fuel based ashes. This is also shown in the leaching analyses. The leaching water from fresh ashes contains a higher concentration of leachable components than aged ashes. When aged the pH in the ashes decreases due to carbon uptake and hydration and this makes metals as Pb, Cu, Cr and Zn less mobile. On the other hand, an increase in leachability of Sb, Mo and SO{sub 4} is shown when the ashes

Possibilities of utilizing power plant fly ashes

Directory of Open Access Journals (Sweden)

Mezencevová Andrea

2003-09-01

Full Text Available The burning of fossil fuels in industrial power stations plays a significant role in the production of thermal and electrical energy. Modern thermal power plants are producing large amounts of solid waste, mainly fly ashes. The disposal of power plant waste is a large environmental problem at the present time. In this paper, possibilities of utilization of power plant fly ashes in industry, especially in civil engineering, are presented. The fly ash is a heterogeneous material with various physical, chemical and mineralogical properties, depending on the mineralogical composition of burned coal and on the used combustion technology. The utilization of fly ashes is determined of their properties. The fineness, specific surface area, particle shape, density, hardness, freeze-thaw resistance, etc. are decisive. The building trade is a branch of industry, which employs fly ash in large quantities for several decades.The best utilization of fluid fly ashes is mainly in the production of cement and concrete, due to the excellent pozzolanic and cementitious properties of this waste. In the concrete processing, the fly ash is utilized as a replacement of the fine aggregate (fine filler or a partial replacement for cement (active admixture. In addition to economic and ecological benefits, the use of fly ash in concrete improves its workability and durability, increases compressive and flexural strength, reduces segregation, bleeding, shrinkage, heat evolution and permeability and enhances sulfate resistance of concrete.The aim of current research is to search for new technologies for the fly ash utilization. The very interesting are biotechnological methods to recovery useful components of fly ashes and unconventional methods of modification of fly ash properties such as hydrothermal zeolitization and mechanochemical modification of its properties. Mechanochemistry deals with physico - chemical transformations and chemical reactions of solids induced by

Fundamental study of ash formation and deposition: Effect of reducing stoichiometry

Energy Technology Data Exchange (ETDEWEB)

Helble, J.J.; Bool, L.E.; Kang, S.G. [and others

1995-11-01

This project is designed to examine the effects of combustion stoichiometry on the fundamental aspects of ash formation and ash deposit initiation. Emphasis is being placed on reducing stoichiometries associated with low-NOx combustion, although a range of oxidant/fuel ratios are being considered. Previous work has demonstrated that ash formation depends strongly upon coal mineralogy, including mineral type, size, amount, and the presence of organically associated inorganic species. Combustion temperature and the oxidation state of iron also play a significant role. As these latter items will vary with changes in stoichiometry, research to determine the net effect on deposition is required.

Preliminary Evaluation of Potassium Extraction from Bamboo Ash

Directory of Open Access Journals (Sweden)

Samadhi Tjokorde W.

2018-01-01

Full Text Available Bamboo is a potentially economical fuel crop that has not been utilized at a substantial extent for energy generation in Indonesia. As a thermal conversion waste, bamboo ash is particularly interesting due to its high potassium content. This paper discusses the determination of several key parameters of a simple batchwise extraction process to recover potassium in the form of weak solution from bamboo ash. To produce the ash, black bamboo (Gigantochloa atroviolaceae is charred in a fixed bed combustor. The bamboo char is ground and ashed at 500 °C in an electric furnace. The ash yield is 3.3 %-mass relative to as-received ash, with an ash K2O content of 12.9 %-mass. The ash is ground until passing 100-mesh standard sieve, and extracted by deionized water on a 2-stage laboratory-scale batchwise extractor battery. Process variables include extractror battery configuration (counter-current and co-current, temperature (nominal setting at 45-80 °C, and contact period of 1-6 hours. The concentration of extracted K2O increases asymptotically with temperature and contact time. Counter-current extraction yields more than twice the extract K2O concentration compared to cross-current extraction. The optimum conditions for the counter-current extraction is identified as a temperature of 78 °C and contact time of 4 hours, resulting in a 0.70 %-mass K2O solution concentration. Spot sampling of commercial liquid fertilizer products in Indonesia indicates an equivalent K2O content of 0.08-13.6 %-mass, suggesting the potential of the bamboo ash extract as an intermediate for fertilizer product.

Recent standardisation work in Sweden related to measurement of biomass fuel quality

Energy Technology Data Exchange (ETDEWEB)

Maansson, Margret [Swedish National Testing and Research Inst., Boraas (Sweden)

1998-06-01

Work on Swedish standards for peat and biofuels started close to fifteen years ago. The same technical committee that has the responsibility for peat and solid biofuels is also handling the standardisation work on solid mineral fuels. Its counterpart within the ISO is TC 27 Solid mineral fuels. A number of the Swedish analysis standards are structured such that they define methods for all of the solid fuels in the same standard, with specific requirements for the type of fuel if necessary. By now, twenty Swedish biomass standards have been prepared and adopted, half of them already revised at least once. There are dedicated biofuel standards for terminology, sampling and sample preparation and for determination of parameters such as moisture, ash, size distribution, bulk density and mechanical strength. Solid fuels standards that include biomass and peat in their range of application exist for the determination of volatile matter, sulfur chlorine and calorific value. Solid fuel ash methods have been specifically developed for the determination of unburned material and sulfur content. At the present time, standard methods are being defined for the determination of total amounts of heavy metals in ash, and also methods for measuring the availability (leaching properties) of certain elements in ash, in particular ash from combustion of biomass. Ash methods are of interest because of the focus on the possibilities of returning biomass-origin ash to forest soil as a fertilizer and also to prevent depletion of trace elements caused by the increase in the utilisation of the forest growth

Incineration ash conditioning processes

International Nuclear Information System (INIS)

Jouan, A.; Ouvrier, N.; Teulon, F.

1990-01-01

Incinerable wastes consist of the following standard composition corresponding to projected wastes from a future mixed oxide fuel fabrication plant with an annual throughput of 1700 kg (i.e. 5.7 m 3 ) of ashes produced by the incineration facility: . 50% polyvinyl chloride (glove box sleeves), . 5% polyethylene (bags), . 35% rubber (equal amounts of latex and neoprene), . 10% cellulose (equal amounts of cotton and cleansing tissues). The work focused mainly on compaction by high-temperature isostatic pressing, is described in some detail with the results obtained. An engineering study was also carried out to compare this technology with two other ash containment processes: direct-induction (cold crucible) melting and cement-resin matrix embedding. Induction melting is considerably less costly than isostatic pressing; the operating costs are about 1.5 times higher than for cement-resin embedding, but the volume reduction is nearly 3 times greater

Diffusion under water-saturated conditions in PFA/OPC-based structural concrete

International Nuclear Information System (INIS)

Harris, A.W.; Nickerson, A.K.

1990-05-01

A substantial proportion of the volume of the UK radioactive waste repository is likely to be composed of materials based on hydraulic cements. This includes the structural components, which are likely to be manufactured from concrete. The mass transport characteristics of dissolved species for a typical structural concrete, based on a mixture of pulverised fuel ash and ordinary Portland cement, have been measured in a water-saturated condition. Both the water permeability and the diffusion parameters (for caesium, strontium and iodide ion and tritiated water diffusion) are low compared to values obtained for other structural concretes. The intrinsic diffusion coefficients for iodide and caesium ions are in the range 2-5x10 -14 m 2 s -1 . There is no evidence of significant sorption of any of the diffusants studied. (author)

Analysis of radioactivity in coal, cinders, fly ash and discharges from the stack

International Nuclear Information System (INIS)

Meide, A.

1985-01-01

Gamma measurements of coal samples originating from several supplying countries proved that the South African coal has about double U-238 and Ra-226 concentration and about treble Th-232 concentration compared to coal from the other countries. Gamma measurements of coal, cinders and fly ash samples from five coal-fueled plants indicate somewhat higher concentrations of Th-232 in cinders and U-238 and Th-232 in fly ashes than those described in literature. The ratio Po-210/Pb-210 was about 2 for fly ash particulates <35μ. A positive correlation between ash percentage and radioactivity of coal might be assumed. (EG)

Behavior of Alkali Metals and Ash in a Low-Temperature Circulating Fluidized Bed (LTCFB) Gasifier

DEFF Research Database (Denmark)

Narayan, Vikas; Jensen, Peter Arendt; Henriksen, Ulrik Birk

2016-01-01

W and a 6 MW LTCFBgasifier. Of the total fuel ash entering the system, the largest fraction (40−50%) was retained in the secondary cyclone bottoms,while a lower amount (8−10%) was released as dust in the exit gas. Most of the alkali and alkaline earth metals were retained inthe solid ash, along with Si...... by the particle size and the cut size ofthe primary and secondary cyclones. A model accounting for the ash collection by the plant cyclones was shown to predict theproduct gas ash particle release reasonably well....

Physico-chemical characteristics of eight different biomass fuels and comparison of combustion and emission results in a small scale multi-fuel boiler

International Nuclear Information System (INIS)

Forbes, E.G.A.; Easson, D.L.; Lyons, G.A.; McRoberts, W.C.

2014-01-01

Highlights: • Physical parameters of the eight biomass fuels examined were all different. • Significant differences were found in Proximate, Ultimate and TGA results. • Energy outputs were not proportionate to dry matter energy content. • Highest flue ash production from fuels with highest fines content. • Flue gas emissions varied significantly, NOx levels correlated with fuel N content. - Abstract: This study describes the results from the investigation of 7 different biomass fuel types produced on a farm, and a commercial grade wood pellet, for their physical, chemical, thermo-gravimetric and combustion properties. Three types of short rotation coppice (SRC) willow, two species of conifers, forest residues (brash), commercially produced wood-pellets and a chop harvested energy grass crop Miscanthus giganteus spp., (elephant grass) were investigated. Significant differences (p < 0.05) were found in most of the raw fuel parameters examined using particle distribution, Thermogravimetric, Ultimate and Proximate analysis. Combustion tests in a 120 kW multi-fuel boiler revealed differences, some significant, in the maximum output, energy conversion efficiency, gaseous emission profiles and ash residues produced from the fuels. It was concluded that some of the combustion results could be directly correlated with the inherent properties of the different fuels. Ash production and gaseous emissions were the aspects of performance that were clearly and significantly different though effects on energy outputs were more varied and less consistent. The standard wood pellet fuel returned the best overall performance and miscanthus produced the largest amount of total ash and clinker after combustion in the boiler

Main characteristics of the radioactive enrichment in ashes produced in coal-fired power stations

International Nuclear Information System (INIS)

Baeza, Antonio; Corbacho, Jose A.; Cancio, David; Robles, Beatriz; Mora, Juan C.

2008-01-01

Under contract with the Spain's 'Nuclear Safety Council', a study is being conducted of the nation's largest nominal output coal-fired power stations. Its purpose is to assess the radiological impact on workers and local populations due to this source of NORM activity. One of the aspects of particular interest is the study of the radioactive enrichment in the combustion wastes relative to the different coals used as fuel (usually local bituminous coal or lignite, or imported coal). These wastes consist of fly ash (mostly fine particles collected in electrostatic precipitators), and bottom ash (larger in size, and collected wet or dry in hoppers below the boilers). In general terms, the enrichment factors measured were between 2 and 18 for the radionuclides 40 K, 226 Ra, 232 Th, and 210 Po. The magnitude of this enrichment factor depended mainly on the ash content of each coal, and hence on the type of coal used as fuel and the specific operation cycle in the different power stations. For the radionuclides 40 K, 226 Ra, and 232 Th, the enrichment was relatively similar in value in the fly and bottom ashes produced by the different types of coal used in the power stations studied. For 210 Po, however, as was expected, the enrichment was much greater in the fly ash than in the bottom ash for each coal analyzed. (author)

Ash reduction system using electrically heated particulate matter filter

Science.gov (United States)

Gonze, Eugene V [Pinckney, MI; Paratore, Jr., Michael J; He, Yongsheng [Sterling Heights, MI

2011-08-16

A control system for reducing ash comprises a temperature estimator module that estimates a temperature of an electrically heated particulate matter (PM) filter. A temperature and position estimator module estimates a position and temperature of an oxidation wave within the electrically heated PM filter. An ash reduction control module adjusts at least one of exhaust flow, fuel and oxygen levels in the electrically heated PM filter to adjust a position of the oxidation wave within the electrically heated PM filter based on the oxidation wave temperature and position.

Stochastic Modelling of the Hydraulic Anisotropy of Ash Impoundment Sediment

Science.gov (United States)

Slávik, Ivan

2017-12-01

In the case reported here the impoundments of a 400 MW coal heated power plant with an annual production of about 1.5 million tons of fuel ash are of the cross-valley type, operated by the simple and cheap „upstream method”. The aim of the research was to determine overall and local values of the permeability in horizontal as well as in vertical direction and the anisotropy of the thin-layered sedimented ash. The coal ashes are hydraulically transported through pipelines in form of a slurry and periodically floated on the beach of the impoundment. The ashes are deposited in the form of a thin-layered sediment, with random alternation of layers with a coarser or finer granularity. The ash impoundment sediment is anthropogenic sediment with horizontally laminated texture. Therefore, the sediment is anisotropic from the viewpoint of water seepage. The knowledge of the permeability and the seepage anisotropy of the sediment is a basic requirement for the design of an appropriate dewatering system. The seepage anisotropy of the ash sediment has been checked by means of stochastic modelling, based on the correlation between the effective grain diameter and the coefficient of permeability of the ash: the effective grain diameter and the thickness of individual layers have been proposed to be random events.

Development of Self-Consolidating High Strength Concrete Incorporating Treated Palm Oil Fuel Ash

Directory of Open Access Journals (Sweden)

Belal Alsubari

2015-04-01

Full Text Available Palm oil fuel ash (POFA has previously been used as a partial cement replacement in concrete. However, limited research has been undertaken to utilize POFA in high volume in concrete. This paper presents a study on the treatment and utilization of POFA in high volume of up to 50% by weight of cement in self-consolidating high strength concrete (SCHSC. POFA was treated via heat treatment to reduce the content of unburned carbon. Ordinary Portland cement was substituted with 0%, 10%, 20%, 30%, and 50% treated POFA in SCHSC. Tests have been conducted on the fresh properties, such as filling ability, passing ability and segregation resistance, as well as compressive strength, drying shrinkage and acid attack resistance to check the effect of high volume treated POFA on SCHSC. The results revealed that compared to the control concrete mix, the fresh properties, compressive strength, drying shrinkage, and resistance against acid attack have been significantly improved. Conclusively, treated POFA can be used in high volume as a cement replacement to produce SCHSC with an improvement in its properties.

Development of Self-Consolidating High Strength Concrete Incorporating Treated Palm Oil Fuel Ash

Science.gov (United States)

Alsubari, Belal; Shafigh, Payam; Jumaat, Mohd Zamin

2015-01-01

Palm oil fuel ash (POFA) has previously been used as a partial cement replacement in concrete. However, limited research has been undertaken to utilize POFA in high volume in concrete. This paper presents a study on the treatment and utilization of POFA in high volume of up to 50% by weight of cement in self-consolidating high strength concrete (SCHSC). POFA was treated via heat treatment to reduce the content of unburned carbon. Ordinary Portland cement was substituted with 0%, 10%, 20%, 30%, and 50% treated POFA in SCHSC. Tests have been conducted on the fresh properties, such as filling ability, passing ability and segregation resistance, as well as compressive strength, drying shrinkage and acid attack resistance to check the effect of high volume treated POFA on SCHSC. The results revealed that compared to the control concrete mix, the fresh properties, compressive strength, drying shrinkage, and resistance against acid attack have been significantly improved. Conclusively, treated POFA can be used in high volume as a cement replacement to produce SCHSC with an improvement in its properties.

Cocombustion of peat and biofuels - ash-related system advantages; Samfoerbraenning av torv och biobraenslen - askrelaterade systemfoerdelar

Energy Technology Data Exchange (ETDEWEB)

Oehman, Marcus [Umeaa Univ. (Sweden). Energy Technology and Thermal Process Chemistry; Burvall, Jan [Swedish Univ. of Agricultural Sciences, Umeaa (Sweden). Unit for Biomass Technology and Chemistry

2006-12-30

In heat and power plants peat fuels are, for combustion technical reasons, often co-combusted in fuel blends together with wood fuels. The aim of the present work has therefore been to investigate the possible interacting effects that cocombustion of peat and biofuels has on the whole bioenergy system with focus on the ash properties. Ash related problems in heat and power plants, especially in fluidised bed combustion (FB), can be minimised by co-combustion of peat and wood fuels. The fuel flexibility is one of the reasons why FB is the most common technology when new boilers are built for heat and power production. When biofuels are burned in FB-boilers total defluidisation has been relatively frequently reported. Co-combustion of peat and biofuels minimise the risk for total defluidisation, which result in an unscheduled plant shut down. For FB-boilers, problems related to the ash properties in the fuel or fuel blends are often observed. Today, co-combustion of peat and biofuels are used in practise for approximately 50 % of all FB-boilers in Sweden. For these plants, the low risk for total defluidisation (translated to economical figures) could be evaluated to 20-30 million SEK or 100 GWh annually. That is because no additional costs will occur for more expensive energy sources such as oil, gas, and electricity. Co-combustion still has a potential to introduce for the rest of the fluidised bed plants in Sweden, which will give approximately the same economical figures as given above. Corrosion problems, which result in unacceptable short lifetime of the super heater tube surfaces, have been reported from approximately 50 % of the biofuel supplied power plants in Sweden. These problems are more frequent in the middle and southern parts of Sweden. The reasons for these problems may be related to that higher use of forests residues and recovered-wood materials containing higher contents of chlorine and alkali. The experience from the owners of the power plants and

Volcanic ash impacts on critical infrastructure

Science.gov (United States)

Wilson, Thomas M.; Stewart, Carol; Sword-Daniels, Victoria; Leonard, Graham S.; Johnston, David M.; Cole, Jim W.; Wardman, Johnny; Wilson, Grant; Barnard, Scott T.

2012-01-01

Volcanic eruptions can produce a wide range of hazards. Although phenomena such as pyroclastic flows and surges, sector collapses, lahars and ballistic blocks are the most destructive and dangerous, volcanic ash is by far the most widely distributed eruption product. Although ash falls rarely endanger human life directly, threats to public health and disruption to critical infrastructure services, aviation and primary production can lead to significant societal impacts. Even relatively small eruptions can cause widespread disruption, damage and economic loss. Volcanic eruptions are, in general, infrequent and somewhat exotic occurrences, and consequently in many parts of the world, the management of critical infrastructure during volcanic crises can be improved with greater knowledge of the likely impacts. This article presents an overview of volcanic ash impacts on critical infrastructure, other than aviation and fuel supply, illustrated by findings from impact assessment reconnaissance trips carried out to a wide range of locations worldwide by our international research group and local collaborators. ‘Critical infrastructure’ includes those assets, frequently taken for granted, which are essential for the functioning of a society and economy. Electricity networks are very vulnerable to disruption from volcanic ash falls. This is particularly the case when fine ash is erupted because it has a greater tendency to adhere to line and substation insulators, where it can cause flashover (unintended electrical discharge) which can in turn cause widespread and disruptive outages. Weather conditions are a major determinant of flashover risk. Dry ash is not conductive, and heavy rain will wash ash from insulators, but light rain/mist will mobilise readily-soluble salts on the surface of the ash grains and lower the ash layer’s resistivity. Wet ash is also heavier than dry ash, increasing the risk of line breakage or tower/pole collapse. Particular issues for water

The certification of the surface density (kg/m sub 2 ) of BCR CRM 038 ('fly ash from pulverised coal') comprised in methyl cellulose films simulating dust charged filters. BCR 128

Energy Technology Data Exchange (ETDEWEB)

Griepink, B; Marchandise, H; Colinet, E; Dams, R

1988-01-01

BCR CRM 38 ('Fly Ash') has been embedded in a stable methylcellulose foil of about 10{mu}m thickness. This has been done by making a slurry of fly ash and methylcellulose in water and spiking it with {sup 42}K as a radioactive tracer. The slurry was spread over glass plates and allowed to dry. 'Filters' of uniform size were punched out of the foil. The surface density (e.g. {mu}g/cm{sup 2}) of the fly ash was calculated for each individual 'filter' by comparing the {sup 42}K-activity of the filter with that of the initial suspension. The uncertainties in the so obtained surface density of random and of systematic origin have been estimated. The total relative uncertainty in the surface density of every element certified in BCR 38 is 4-6%. Studies of stability and homogeneity have revealed that this material is well suited for the verification of the results of non-destructive analytical techniques for dust components.

Co-sintering of treated APC-residues with bottom ash

DEFF Research Database (Denmark)

Jensen, Dorthe Lærke; Bergfeldt, Britta; Vehlow, Jürgen

2001-01-01

the influence of co-sintering of Ferrox products with bottom ashes on the quality of the residues and the effects on the combustion process. Only few elements showed higher concentrations in the bottom ashes of these co-combustion tests compared to reference tests. No significant effect on the leaching......Air pollution control residues stabilised by means of the Ferrox process can be sager disposed of due to lower contents of soluble salts and lesssoluble heavy metals stabilised in iron oxides. Co-combustion tests in the Karlsruhe test incinerator TAMARA were carried out in order to investigate...... behaviour of the bottom ashes could be found. During the co-combustion process an increase in SO2 concentrations in the raw gas and slightly lower temperatures in the fuel bed could be observed....

An SEM/EDX study of bed agglomerates formed during fluidized bed combustion of three biomass fuels

International Nuclear Information System (INIS)

Scala, Fabrizio; Chirone, Riccardo

2008-01-01

The agglomeration behaviour of three biomass fuels (exhausted and virgin olive husk and pine seed shells) during fluidized bed combustion in a lab-scale reactor was studied by means of SEM/EDX analysis of bed agglomerate samples. The effect of the fuel ash composition, bed temperature and sand particle size on agglomeration was investigated. The study was focused on the main fuel ash components and on their interaction with the bed sand particles. Agglomeration was favoured by high temperature, small sand size, a high fraction of K and Na and a low fraction of Ca and Mg in the fuel ash. An initial fuel ash composition close to the low-melting point eutectic composition appears to enhance agglomeration. The agglomerates examined by SEM showed a hollow structure, with an internal region enriched in K and Na where extensive melting is evident and an external one where sand particles are only attached by a limited number of fused necks. Non-molten or partially molten ash structures deposited on the sand surface and enriched in Ca and Mg were also observed. These results support an ash deposition-melting mechanism: the ash released by burning char particles inside the agglomerates is quantitatively deposited on the sand surface and then gradually embedded in the melt. The low-melting point compounds in the ash migrate towards the sand surface enriching the outermost layer, while the ash structure is progressively depleted of these compounds

Flame image monitoring and analysis in combustion management

Energy Technology Data Exchange (ETDEWEB)

Popovic, D [CEZ, a.s. Elektrarna Detmarovice, Detmarovice (Czech Republic); Huttunen, A J; Nihtinen, J J [Imatran Voima Oy, IVO Technology Centre, Vantaa (Finland)

1998-12-31

When NO{sub x} emissions are reduced with new low-NO{sub x} burners and infurnace modifications in old pulverised fuel boilers, many changes in the firing conditions may occur. Depending on coal quality and the original furnace design, low-NO{sub x} burners, overtire air, low-excess-air firing and other primary modifications in various combinations may cause flame instability, increased slagging, increased minimum load and other difficulties in controlling the burning process. To find and solve these problems quicker, a new type of burner management system for pulverised fuel and oil-fired boilers was developed by Imatran Voima Oy. The DIMAC combustion management system monitors and analyses individually each burner or burner level. There are special software for wall and corner fired boilers. The DIMAC system is comprised of two functional subsystems: flame monitoring and flame analysis. The DIMAC enables the power plant operators to minimise NO{sub x} emissions and optimise the burning efficiency with varying coal qualities and boiler loads at the same time so that slagging, unburnt carbon in fly ash and flame stability stay in acceptable limits. It also guarantees that burners operate in good safety conditions in each burner level. The DIMAC system monitors perpendicularly each individual burner and evaluates flame parameters. Real-time flame monitoring and analysis allows the operator to directly see the effect of changing fuel distribution on flame pattern and flame stability. Based on data from the DIMAC references the system can improve boiler efficiency by 0.2 - 0.5 per cent unit as a result of more efficient control of the burning process. At the same time, the NO{sub x} formation can be reduced by 10 - 20 % 2 refs.

Flame image monitoring and analysis in combustion management

Energy Technology Data Exchange (ETDEWEB)

Popovic, D. [CEZ, a.s. Elektrarna Detmarovice, Detmarovice (Czech Republic); Huttunen, A.J.; Nihtinen, J.J. [Imatran Voima Oy, IVO Technology Centre, Vantaa (Finland)

1997-12-31

When NO{sub x} emissions are reduced with new low-NO{sub x} burners and infurnace modifications in old pulverised fuel boilers, many changes in the firing conditions may occur. Depending on coal quality and the original furnace design, low-NO{sub x} burners, overtire air, low-excess-air firing and other primary modifications in various combinations may cause flame instability, increased slagging, increased minimum load and other difficulties in controlling the burning process. To find and solve these problems quicker, a new type of burner management system for pulverised fuel and oil-fired boilers was developed by Imatran Voima Oy. The DIMAC combustion management system monitors and analyses individually each burner or burner level. There are special software for wall and corner fired boilers. The DIMAC system is comprised of two functional subsystems: flame monitoring and flame analysis. The DIMAC enables the power plant operators to minimise NO{sub x} emissions and optimise the burning efficiency with varying coal qualities and boiler loads at the same time so that slagging, unburnt carbon in fly ash and flame stability stay in acceptable limits. It also guarantees that burners operate in good safety conditions in each burner level. The DIMAC system monitors perpendicularly each individual burner and evaluates flame parameters. Real-time flame monitoring and analysis allows the operator to directly see the effect of changing fuel distribution on flame pattern and flame stability. Based on data from the DIMAC references the system can improve boiler efficiency by 0.2 - 0.5 per cent unit as a result of more efficient control of the burning process. At the same time, the NO{sub x} formation can be reduced by 10 - 20 % 2 refs.

Use of ashes from straw and grass on agricultural land. Conditions and recommendations; Spridning av aska fraan straabraenslen paa aakermark. Foerutsaettningar och rekommendationer

Energy Technology Data Exchange (ETDEWEB)

Hadders, G.; Floden, S.

1997-12-31

The composition of ashes from straw fuel varies depending on the plant species, any fertilisation during the growing season, and weather conditions during the year in question, etc. The composition of ashes will also vary depending on what type of boiler the fuel has been combusted in. In this report the discussion has been restricted to so-called `grate boilers` with a capacity of <5 MW. In such boilers one can distinguish between the so-called `bottom ashes` from the boiler grate and the `fly-ashes` which are extracted from exhaust gases. Today there are no regulations prescribing how ashes from straw and energy crops shall be handled. However, there is a policy on biofuel ash recycling which was developed by the Swedish Environmental Protection Agency. In their policy the Environmental Protection Agency states that `whatever is removed may be returned`. Through the use of ashes from straw fuels as plant nutrients, the nutrients removed at harvest are returned. At the same time new supplies of minerals from external sources, and thereby following input of undesirable substances such as for instance cadmium, are avoided. The alternative i.e., dumping the ashes in landfills, results in unnecessary costs. In an explanatory note accompanying the agency document, it is stated that the ashes should preferably be returned to the crop and soil from which they had originated. If the ashes are to be spread on other land, the agency proposes that the restrictions imposed on sludge applications be applied here as well. In our opinion, it would be unreasonable for limitations on the use of ashes from agricultural crops as plant nutrients to be more strict than those concerning the use of fertilizers. Since chemical fertilizers can be used on any type of crop, there is no logical reason why the same should not also apply to ashes from straw fuels. Thus we recommend that the application of such ashes to non-energy crops be allowed. If there is reason to suspect high contents of

Composition, diagenetic transformation and alkalinity potential of oil shale ash sediments

International Nuclear Information System (INIS)

Motlep, Riho; Sild, Terje; Puura, Erik; Kirsimaee, Kalle

2010-01-01

Oil shale is a primary fuel in the Estonian energy sector. After combustion 45-48% of the oil shale is left over as ash, producing about 5-7 Mt of ash, which is deposited on ash plateaus annually almost without any reuse. This study focuses on oil shale ash plateau sediment mineralogy, its hydration and diagenetic transformations, a study that has not been addressed. Oil shale ash wastes are considered as the biggest pollution sources in Estonia and thus determining the composition and properties of oil shale ash sediment are important to assess its environmental implications and also its possible reusability. A study of fresh ash and drillcore samples from ash plateau sediment was conducted by X-ray diffractometry and scanning electron microscopy. The oil shale is highly calcareous, and the ash that remains after combustion is derived from the decomposition of carbonate minerals. It is rich in lime and anhydrite that are unstable phases under hydrous conditions. These processes and the diagenetic alteration of other phases determine the composition of the plateau sediment. Dominant phases in the ash are hydration and associated transformation products: calcite, ettringite, portlandite and hydrocalumite. The prevailing mineral phases (portlandite, ettringite) cause highly alkaline leachates, pH 12-13. Neutralization of these leachates under natural conditions, by rainwater leaching/neutralization and slow transformation (e.g. carbonation) of the aforementioned unstable phases into more stable forms, takes, at best, hundreds or even hundreds of thousands of years.

Composition, diagenetic transformation and alkalinity potential of oil shale ash sediments

Energy Technology Data Exchange (ETDEWEB)

Motlep, Riho, E-mail: riho.motlep@ut.ee [Department of Geology, University of Tartu, Ravila 14A, 50411 Tartu (Estonia); Sild, Terje, E-mail: terje.sild@maaamet.ee [Estonian Land Board, Mustamaee tee 51, 10621 Tallinn (Estonia); Puura, Erik, E-mail: erik.puura@ut.ee [Institute of Technology, University of Tartu, Nooruse 1, 50411 Tartu (Estonia); Kirsimaee, Kalle, E-mail: kalle.kirsimae@ut.ee [Department of Geology, University of Tartu, Ravila 14A, 50411 Tartu (Estonia)

2010-12-15

Oil shale is a primary fuel in the Estonian energy sector. After combustion 45-48% of the oil shale is left over as ash, producing about 5-7 Mt of ash, which is deposited on ash plateaus annually almost without any reuse. This study focuses on oil shale ash plateau sediment mineralogy, its hydration and diagenetic transformations, a study that has not been addressed. Oil shale ash wastes are considered as the biggest pollution sources in Estonia and thus determining the composition and properties of oil shale ash sediment are important to assess its environmental implications and also its possible reusability. A study of fresh ash and drillcore samples from ash plateau sediment was conducted by X-ray diffractometry and scanning electron microscopy. The oil shale is highly calcareous, and the ash that remains after combustion is derived from the decomposition of carbonate minerals. It is rich in lime and anhydrite that are unstable phases under hydrous conditions. These processes and the diagenetic alteration of other phases determine the composition of the plateau sediment. Dominant phases in the ash are hydration and associated transformation products: calcite, ettringite, portlandite and hydrocalumite. The prevailing mineral phases (portlandite, ettringite) cause highly alkaline leachates, pH 12-13. Neutralization of these leachates under natural conditions, by rainwater leaching/neutralization and slow transformation (e.g. carbonation) of the aforementioned unstable phases into more stable forms, takes, at best, hundreds or even hundreds of thousands of years.

Electrodialytic remediation of fly ash from co-combustion of wood and straw

DEFF Research Database (Denmark)

Chen, Wan; Jensen, Pernille Erland; Ottosen, Lisbeth M.

2015-01-01

The heavy metal content in fly ash from biomass combustion, such as straw, wood and sludge, often needs reducing before the ash can be used as fertilizer for agricultural land or as a component in the production of construction materials. In this study, fly ash from a boiler fueled with wood chips...... and straw was treated either by electrodialytic remediation (EDR) directly or by a combination of EDR and pre-wash with distilled water to investigate the possibilities of reducing the heavy metal content and reusing nutrients as fertilizer and bulk material in construction materials. Different experimental....../pre-wash-EDR treated ash mainly contained quartz, and the X-ray diffraction (XRD) peaks of K salts had disappeared. This shows that the potassium fertilizer potential was lost in the treated ashes, but the quartz mineral is beneficial in construction materials, such as ceramics. The K fertilizer could be recovered...

The Effect of Variation of Molarity of Alkali Activator and Fine Aggregate Content on the Compressive Strength of the Fly Ash: Palm Oil Fuel Ash Based Geopolymer Mortar

Directory of Open Access Journals (Sweden)

Iftekhair Ibnul Bashar

2014-01-01

Full Text Available The effect of molarity of alkali activator, manufactured sand (M-sand, and quarry dust (QD on the compressive strength of palm oil fuel ash (POFA and fly ash (FA based geopolymer mortar was investigated and reported. The variable investigated includes the quantities of replacement levels of M-sand, QD, and conventional mining sand (N-sand in two concentrated alkaline solutions; the contents of alkaline solution, water, POFA/FA ratio, and curing condition remained constant. The results show that an average of 76% of the 28-day compressive strength was found at the age of 3 days. The rate of strength development from 3 to 7 days was found between 12 and 16% and it was found much less beyond this period. The addition of 100% M-sand and QD shows insignificant strength reduction compared to mixtures with 100% N-sand. The particle angularity and texture of fine aggregates played a significant role in the strength development due to the filling and packing ability. The rough texture and surface of QD enables stronger bond between the paste and the fine aggregate. The concentration of alkaline solution increased the reaction rate and thus enhanced the development of early age strength. The use of M-sand and QD in the development of geopolymer concrete is recommended as the strength variation between these waste materials and conventional sand is not high.

Advanced characterisation of municipal solid waste ashes

Energy Technology Data Exchange (ETDEWEB)

Skytte Pedersen, Randi

2002-12-15

This report deals with characterisation of Municipal Solid Waste (MSW) ashes from the Danish power plant Maebjergvaerket, Holstebro. MSW has been used as a fuel since the mid 1960's and since then, the MSW incineration plants have experienced operational problems due to deposit formation and corrosion. Inorganic elements tightly or loosely bound in the waste are the main cause of these problems. The tightly bound elements will mainly stay on the grate during combustion, whereas the loosely bound elements are volatilised and recondensed elsewhere in the furnace. Many of the heavy metals form volatile chlorides during the incineration, and the fly ash fraction thus show enrichment in these elements. Presence of chlorides and heavy metals in deposits may cause severe corrosion due to formation of low-melting eutectics. Chlorine gas in the flue gas is also of major concern with respect to corrosion, due to formation of volatile chlorides when chlorine comes in contact with the tube material. Four different ash fractions (bottom ash, super heater ash, economiser ash and fly ash) taken from Maebjergvaerket have been analysed with respect to particle sizes, structures, shapes and composition. The applied methods were scanning electron microscopy (SEM), energy dispersive X-ray analyses (EDX) and mapping, which were used in order to determine sizes, chemical composition and structure of the particles. X-ray powder diffraction (XRD) was used to provide information about crystallography and mineral phases. Chemical analysis was also performed along with a particle size distribution for the fine-grained fractions (economiser and fly ash). The amount of silicates consisting of Ca, Al and Si, were found to decrease through the furnace, whereas the amount of alkali (Na, K) chlorides and heavy metals (Pb, Zn) increased. The bonding in the waste before incineration is the direct cause of this, since silicates are tightly bound and chlorides are loosely bound. There was a

System for manufacturing ash products and energy from refuse waste

Energy Technology Data Exchange (ETDEWEB)

Sutin, G.L.; Mahoney, P.F.

1996-01-04

The present invention provides a system of manufacturing energy and ash products from solid waste. The system includes apparatus for receiving solid waste for processing, apparatus for shredding the received solid waste, apparatus for removing ferrous material from the shredded solid waste to create processed refuse fuel (PRF) and apparatus for efficiently combusting the PRF. A conveyor transfers the PRF to the combusting apparatus such that the density of the PRF is always controlled for continuous non-problematic flow. Apparatus for recovering residual combustion particulate from the combustion residual gases and for recovering solid ash residue provides the system with the ability to generate steam and electrical energy, and to recover for reuse and recycling valuable materials from the solid ash residue. (author) figs.

Evaluation of rice husk ash as filler in tread compounds

International Nuclear Information System (INIS)

Fernandes, M. R. S.; Furtado, C. R. G.; Sousa, A. M. F. de

2014-01-01

Rice which is one of the largest agriculture crops produces around 22% of rice rusk during its milling process. This material is mainly used as fuel for energy generation, which results in an ash, which disposal represents an environmental issue. The rice husk ash (RHA) contains over than 70% of silica in an amorphous form and a lot of applications is being developed for it all over the world. The use of silica as a filler in the tire industry is growing since it contributes significantly to the reduction of fuel consumption of the automobiles, allowing at the same time better traction (safety). This paper presents an evaluation of the use of RHA as filler in rubber tread compounds prepared in lab scale and compares its performance with compounds prepared with commercial silica and carbon black, the fillers normally used in tire industry. Mechanical and rheological properties are evaluated, with emphasis for tan delta as an indicator of tread performance related with rolling resistance (fuel consumption) and wet grip/traction (safety)

Evaluation of rice husk ash as filler in tread compounds

Energy Technology Data Exchange (ETDEWEB)

Fernandes, M. R. S., E-mail: monica.fernandes@lanxess.com [Lanxess Elastômeros do Brasil S.A., Brasil and Instituto de Química, Universidade do Estado do Rio de Janeiro (UERJ) (Brazil); Furtado, C. R. G., E-mail: russi@globo.com, E-mail: ana.furtado.sousa@gmail.com; Sousa, A. M. F. de, E-mail: russi@globo.com, E-mail: ana.furtado.sousa@gmail.com [Instituto de Química, Universidade do Estado do Rio de Janeiro (UERJ) (Brazil)

2014-05-15

Rice which is one of the largest agriculture crops produces around 22% of rice rusk during its milling process. This material is mainly used as fuel for energy generation, which results in an ash, which disposal represents an environmental issue. The rice husk ash (RHA) contains over than 70% of silica in an amorphous form and a lot of applications is being developed for it all over the world. The use of silica as a filler in the tire industry is growing since it contributes significantly to the reduction of fuel consumption of the automobiles, allowing at the same time better traction (safety). This paper presents an evaluation of the use of RHA as filler in rubber tread compounds prepared in lab scale and compares its performance with compounds prepared with commercial silica and carbon black, the fillers normally used in tire industry. Mechanical and rheological properties are evaluated, with emphasis for tan delta as an indicator of tread performance related with rolling resistance (fuel consumption) and wet grip/traction (safety)

Modelling of landfill gas adsorption with bottom ash for utilization of renewable energy

Energy Technology Data Exchange (ETDEWEB)

Miao, Chen

2011-10-06

Energy crisis, environment pollution and climate change are the serious challenges to people worldwide. In the 21st century, human being is trend to research new technology of renewable energy, so as to slow down global warming and develop society in an environmentally sustainable method. Landfill gas, produced by biodegradable municipal solid waste in landfill, is a renewable energy source. In this work, landfill gas utilization for energy generation is introduced. Landfill gas is able to produce hydrogen by steam reforming reactions. There is a steam reformer equipment in the fuel cells system. A sewage plant of Cologne in Germany has run the Phosphoric Acid Fuel Cells power station with biogas for more than 50,000 hours successfully. Landfill gas thus may be used as fuel for electricity generation via fuel cells system. For the purpose of explaining the possibility of landfill gas utilization via fuel cells, the thermodynamics of landfill gas steam reforming are discussed by simulations. In practice, the methane-riched gas can be obtained by landfill gas purification and upgrading. This work investigate a new method for upgrading-landfill gas adsorption with bottom ash experimentally. Bottom ash is a by-product of municipal solid waste incineration, some of its physical and chemical properties are analysed in this work. The landfill gas adsorption experimental data show bottom ash can be used as a potential adsorbent for landfill gas adsorption to remove CO{sub 2}. In addition, the alkalinity of bottom ash eluate can be reduced in these adsorption processes. Therefore, the interactions between landfill gas and bottom ash can be explained by series reactions accordingly. Furthermore, a conceptual model involving landfill gas adsorption with bottom ash is developed. In this thesis, the parameters of landfill gas adsorption equilibrium equations can be obtained by fitting experimental data. On the other hand, these functions can be deduced with theoretical approach

Energy properties of solid fossil fuels and solid biofuels

International Nuclear Information System (INIS)

Holubcik, Michal; Jandacka, Jozef; Kolkova, Zuzana

2016-01-01

The paper deals about the problematic of energy properties of solid biofuels in comparison with solid fossil fuels. Biofuels are alternative to fossil fuels and their properties are very similar. During the experiments were done in detail experiments to obtain various properties of spruce wood pellets and wheat straw pellets like biofuels in comparison with brown coal and black coal like fossil fuels. There were tested moisture content, volatile content, fixed carbon content, ash content, elementary analysis (C, H, N, S content) and ash fusion temperatures. The results show that biofuels have some advantages and also disadvantages in comparison with solid fossil fuels.

Energy properties of solid fossil fuels and solid biofuels

Energy Technology Data Exchange (ETDEWEB)

Holubcik, Michal, E-mail: michal.holubcik@fstroj.uniza.sk; Jandacka, Jozef, E-mail: jozef.jandacka@fstroj.uniza.sk [University of Žilina, Faculty of Mechanical Engineering, Department of Power Engineering, Univerzitná 8215/1, 010 26 Žilina (Slovakia); Kolkova, Zuzana, E-mail: zuzana.kolkova@rc.uniza.sk [Research centre, University of Žilina, Univerzitna 8215/1, 010 26 Žilina (Slovakia)

2016-06-30

The paper deals about the problematic of energy properties of solid biofuels in comparison with solid fossil fuels. Biofuels are alternative to fossil fuels and their properties are very similar. During the experiments were done in detail experiments to obtain various properties of spruce wood pellets and wheat straw pellets like biofuels in comparison with brown coal and black coal like fossil fuels. There were tested moisture content, volatile content, fixed carbon content, ash content, elementary analysis (C, H, N, S content) and ash fusion temperatures. The results show that biofuels have some advantages and also disadvantages in comparison with solid fossil fuels.

Large-scale ash recycling in Central Sweden; Storskalig askhantering i mellansverige

Energy Technology Data Exchange (ETDEWEB)

Hansson, Mats [Stora Skog (Sweden)

1998-08-01

When logging residues (tops, branches) are withdrawn from the forest, most of the nutrient content of the trees is also lost. Some of the nutrient content of the soil is restored by weathering, but not all. When biomass is burnt as fuel most of the nutrients will be found in the ash. By recycling wood ash, in similar amounts as was withdrawn with the biomass, it is possible to compensate for the nutrient losses. This project was initiated to study how a rational recycling of wood ash could be performed under conditions valid for Stora, a large forest company in the middle of Sweden. A second aim was to give guiding principles for Stora`s own ash recycling while awaiting instructions from the authorities. In the project both theoretical studies and practical field studies were carried out. Studied areas are production of a stabilised ash product and different systems for transport and spreading of the ash product. The costs and results of spreading have also been monitored. The project showed that spreading of the ash can normally only take place when there is no snow. If production or transport is carried out during another time of the year, the ash has to be stored, either at the industry, in an intermediate storage, or in the forest. One important conclusion from the test period was that the result of the spreading depends heavily on the quality of the ash. Some of the ashes hardened in the spreading equipment, causing a complete stop of the spreading. It also caused problems if the ash was too wet. Plate-spreaders led to unequal quality of spreading, where some areas got more ash and some got less. Granulated ash was most easy to spread. Recommended system for spreading ash is: granulated ash transported unpacked in separate transports with lorries with exchangeable platforms. A large fores tractor spreads the ash in clearings, in the summer. The project has shown that large-scale ash recycling is possible to realize 22 figs, 5 tabs, 13 appendices

The Utilization of Bottom Ash Coal for Briquette Products by Adding Teak Leaves Charcoal, Coconut Shell Charcoal, and Rice Husk Charcoal

Directory of Open Access Journals (Sweden)

Syafrudin Syafrudin

2015-01-01

Full Text Available The limitations of the availability of energy sources especially fuel oil has become a serious threat for the society. The use of coal for energy source as the replacement of fuel oil, in one hand, is very profitable, but on the other hand, will cause problem which is the coal ash residue. This coal ash is a by-product of coal combustion. This coal ash contains bottom ash. Through this observation, the bottom ash can be processed to be charcoal if added by teak leaves, coconut shell, and rice husk. Also, this observation needs to add binder materials for further processing in order to form briquette. It can be used as alternative fuel, the utilization of bottom ash and biomass will give positive impact to the environment. This observation was conducted by using compositions such as bottom ash, teak leaves, coconut shell, and rice husk. The treatment was using comparison 100%:0% ; 80%:20% ; 60%:40% ; 50%:50% ; 40%:60% ; 20%:80% ; 0%:100%. The result that the best briquette was on the composition of 20% bottom ash : 80% coconut shell. The characteristic values from that composition were moisture content of 3.45%, ash content of 17,32%, calorific value of 7.945,72 Cal/gr, compressive strength of 2,18 kg/cm2, level of CO of 105 mg/m3, and heavy metals Cu of 29,83 µg/g and  Zn 32,99 µg/g. The characteristic value from each briquette composition treatment showed that the increasing usage proportion of biomass as added material for briquette was able to increase its moisture content and calorific value. Besides, it is also able to decrease its ash content and compressive strength

Effect of fuel type and deposition surface temperature on the growth and structure of ash deposit collected during co-firing of coal with sewage-sludge, saw-dust and refuse derived fuel

Energy Technology Data Exchange (ETDEWEB)

Kupka, Tomasz; Zajac, Krzysztof; Weber, Roman [Clausthal Univ. of Technology, Clausthal-Zellerfeld (Germany). Inst. of Energy Process Engineering and Fuel Technology

2008-07-01

Blends of a South African bituminous ''Middleburg'' coal and three alternative fuels (a municipal sewage-sludge, a saw-dust and a refuse derived fuel) have been fired in the slagging reactor to examine the effect of the added fuel on slagging propensity of the mixtures. Two kinds of deposition probes have been used, un-cooled ceramic probes and air-cooled steal probes. Distinct differences in physical and chemical structures of the deposits collected using the un-cooled ceramic probes and air-cooled metal probes have been observed. Glassy, easily molten deposits collected on un-cooled ceramic deposition probes were characteristic for co-firing of municipal sewage-sludge with coal. Porous, sintered (not molten) but easily removable deposits of the same fuel blend have been collected on the air-cooled metal deposition probes. Loose, easy removable deposits have been sampled on air-cooled metal deposition probe during co-firing of coal/saw-dust blends. The mass of the deposit sampled at lower surface temperatures (550-700 C) was always larger than the mass sampled at higher temperatures (1100-1300 C) since the higher temperature ash agglomerated and sintered much faster than the low temperature deposit. (orig.)

Stabilization of ash from combustion of MSW in a fluidised bed boiler

Energy Technology Data Exchange (ETDEWEB)

Steenari, Britt-Marie; Wilewska, Magda [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Environmental Inorganic Chemistry

2004-06-01

Due to restrictions against the land filling of combustible waste and directives from authorities that favour energy recovery from the waste, combustion of household waste is becoming more common. Even though combustion of MSW reduces the volume of waste to be handled by approximately 90%, it produces ash residues containing most of the metals present in the original fuel and a number of other species carried through the boiler or formed during combustion. The residues can be divided into three categories: 1. Stable, inert ash that can be utilised in, for example, construction applications 2. Ash that is stable enough to be land filled as nonhazardous waste 3. Ash that contains large amounts of soluble components and potentially toxic metal species. The regulations considering leaching of ash components set limits for the release of soluble salts and toxic metals. Some fly ashes show low leachability for metals but gives a salt release that is too close to the limit for total dissolved solids. Since fly ash from FBC boilers represent the largest volume of ash from these boilers there is a need for a simple and cheap treatment method that reduces the amount of soluble salts, i.e. NaCl, KCl etc, in the ash. After stabilisation, the ash is supposed to go into a more stable category. The aim of this project has been to investigate the applicability of a method to wash such an ash with water. The work included laboratory studies of the ash properties, the water washing process, filtration properties of the ash slurry and also tests of the method in pilot scale at a full scale boiler. This work has been concentrated towards the investigation of cyclone ash from a bubbling fluidised bed boiler in Lidkoeping fired with 100% household waste. Elemental composition of ash samples before and after washing/filtration was determined by AAS or ICP after a suitable dissolution of the sample. The mineralogy of ash samples was analysed using X-ray powder diffractometry. This method

A database for the program 'Environmentally correct utilization of ashes'; Databas inom delprogrammet 'Miljoeriktig anvaendning av askor'

Energy Technology Data Exchange (ETDEWEB)

Bjurstroem, Henrik; Rydstrand, Camilla; Berg, Magnus; Wikman, Karin [AaF-Energi and Miljoe AB, Stockholm (Sweden)

2004-01-01

In the program 'Environmentally correct utilization of ashes' that is active 2002-2005 at the Swedish Thermal Research Institute (Vaermeforsk), R and D studies of the properties of ashes or combustion residues are being carried out and will be carried out. It may be difficult to obtain an overview of these data if these are dispersed in a large number of reports. These data are valuable as they may be used as references on the properties of ashes (these do vary widely, and knowledge of the range within which they vary as well of as the cause to effect chain is far from exhaustive). They also form a basis for continued work in this area. Furthermore, one of the aims of the R and D program is to define criteria for the use of ashes in various situations. Such criteria are generally formulated using quantitative requirements on technical as well as environmental properties. A flexible database has been created in Access in order to store these data on ashes as an easy-to-access reference. The goal was satisfaction of both a user of ashes and a producer of ashes. The information that can be stored stretches from the fuel, the design of the combustion plant to properties specific to a given utilization such as shear module or permeability. Attention has especially been paid to the facts that fuels are often mixed and that ashes are often mixed with other ashes or with other materials. In this first stage, data have been stored in the database for 22 ash samples that have been studied in eight R and D projects.

Guide to Radiation Safety regulations and guidelines (SSMFS 2012:3) on the management of contaminated ash

International Nuclear Information System (INIS)

Moere, Hans

2012-06-01

Energy producers burning peat or wood fuel can obtain ash that is contaminated with cesium-137 from Tjernobyl accident or naturally occurring uranium, thorium and potassium, from some peat bogs. Regulations (SSMFS 2012:3) have been developed which regulates how the contaminated ash should be handled. The regulations affect all who handle contaminated ash in incinerators, landfills, public works, ash recycling, transportation or recycling of ash in other ways. Radiation Safety regulations and guidelines (SSMFS 2012:3) on the management of contaminated ash will apply from 1 September 2012. At that time Regulations (SSMFS 2008:16) on the management of ash that is contaminated with cesium-137, ceases to apply. The contents have been incorporated into the new regulations. This report provides explanations and guidance to the Regulations in order to facilitate the practical application. This guidance is not legally binding

Re-burning of ash in grate boilers; Omfoerbraenning av askor i rosterpannor

Energy Technology Data Exchange (ETDEWEB)

Bergqvist, Kristina; Myringer, Aase; Nordgren, Daniel; Rydberg, Stina [Vattenfall Utveckling AB, Aelvkarleby (Sweden)

2005-03-01

High contents of unburnt carbon in ashes that are dumped or recycled, is questionable from both an economical and an environmental point of view. The content of unburnt carbon in bottom and fly ash from grate boilers varies greatly between different plants but can sometimes exceed 50 %. Re-burning of ash that is separated before a final dust separation, is a relatively cheep and simple method for reducing the content of unburnt carbon in ash, which both reduces the fuel cost and the deposit cost, i.e. the cost of landfilling or recycling. As from 2005 it is prohibited to deposit ash with a too high content of unburnt organic material; the content is limited to 18 weight % of unburnt carbon. The study was carried out in two phases. The aim of the first phase was to map the different techniques used for re-burning ash that are used in grate boilers today. The mapping was done through telephone interviews and comprises technical descriptions of the systems, gathering of operational know-how, installations costs and the effect of the systems on the amount of ash generated at the plants and the content of unburnt carbon in the ash. In order to accomplish a deeper technical and economical evaluation of ash re-burning systems, the second phase involved field studies at two plants. In addition screening tests were done to investigate the connection between the content of unburnt carbon and particle size. The potential of reducing the amount of circulated inorganic material by sieving the ash before bringing it back to the furnace could thereby be determined. 13 plants that utilize re-burning of ash were identified, of which two plants re-burn the bottom ash that floats up to the surface in the wet ash removal system. The remaining 11 plants re-burn fly ash. At three plants the fly ash is first separated in a mesh sieve or similar equipment and only the coarser fly ash is re-burnt. As the amount of bottom ash that surfaces in the wet ash-removal is relatively small

The development of a code of practice for the environmental sound use of PFA as a fill

Energy Technology Data Exchange (ETDEWEB)

Coombs, R.; Sear, L.K.A. [National Power, Selby (United Kingdom). Quality Ash Association

2000-07-01

Although pulverised fuel ash (PFA) has been successfully used in a range of applications for many years there has always been need to give consideration to its environmental impact. The increasing awareness of environmental issues has had an impact on sales, with the need to assess its use on a site by site basis, the time taken to get approval for the use of PFA can exceed the time scales imposed by site operations. There has therefore been a need for an alternative approach to the problem. This paper details the approach at present being developed. This is a three-stage one with an initial assessment of the process, a review of existing data and what further data are required and finally a code of practice that recommends a rational approach to the use of PFA as a fill. 6 refs., 3 tabs.

Flowsheet finalisation for immobilisation of SGHWR wastes

International Nuclear Information System (INIS)

Lee, D.J.

1984-09-01

This report summarises research and development work carried out during the year ended March 1983 on the programme for cementing the Winfrith Reactor (SGHWR) sludge. Further results from the characterisation programme are reported, together with data from the cementation programme. Formulations based on Ordinary Portland Cement (OPC), ground granulated blast furnace slag (BFS) and Pulverised Fuel Ash (PFA) have been tested. The results show that a blend of 90% BFS/10% OPC by weight, gives the best properties. Chemical pretreatment as a method for producing a stable waste form is discussed. A dewatering pretreatment to provide a sludge suitable for direct cementation is also outlined. A flowsheet for cementing the SGHWR sludge is proposed based on these laboratory and pilot scale studies. The major components required for the active plant are identified and provisional plant layouts are given. (author)

Protecting black ash from the emerald ash borer

Science.gov (United States)

Les Benedict

2010-01-01

Black ash (Fraxinus nigra) is an important resource for Tribes in the Northeast and Great Lakes regions of the North American continent. Ash in North America is being threatened with widespread destruction as a result of the introduction of emerald ash borer beetle (Agrilus planipennis) in 2002. Measures are being taken to slow the spread of emerald ash borer beetle....

A new device for the efficient pulverisation and extraction of myocardial biopsies for high energy phosphate analysis.

Science.gov (United States)

Speir, E H; Sullivan, J; Patterson, R E

1985-07-01

We developed a new device for processing frozen myocardial biopsies. Frozen samples of 20 to 50 mg were dropped into a 25 ml stainless steel centrifuge tube held in a custom-made aluminium container precooled in liquid nitrogen. A stainless steel pestle attached to a stainless steel disk was driven by a modified heavy-duty staple gun to pulverise the tissue rapidly at low temperatures. The tissue powder was extracted with 0.3N PCA at 0 degree C in the centrifuge tube which was then transferred to a Sorvall super-speed centrifuge. Values for adenosine triphosphate (ATP) were 5.6 +/- 0.7 mumol . g-1 wet weight (mean +/- SD). Creatine phosphate (CP) yield was 12.2 +/- 3 mumol . g-1 wet weight. The % recovery of an added internal standard for ATP was 86 +/- 18% and for CP 90 +/- 16% with the new method.

The effect of low-NOx combustion on residual carbon in fly ash and its adsorption capacity for air entrainment admixtures in concrete

DEFF Research Database (Denmark)

Pedersen, Kim Hougaard; Jensen, Anker Degn; Dam-Johansen, Kim

2010-01-01

been combusted in an entrained flow reactor to test the impact of changes in operating conditions and fuel type on the AEA adsorption of ash and NOx formation. Increased oxidizing conditions, obtained by improved fuel-air mixing or higher excess air, decreased the AEA requirements of the produced ash......Fly ash from pulverized coal combustion contains residual carbon that can adsorb the air-entraining admixtures (AEAs) added to control the air entrainment in concrete. This is a problem that has increased by the implementation of low-NOx combustion technologies. In this work, pulverized fuel has...... by up to a factor of 25. This was due to a lower carbon content in the ash and a lower specific AEA adsorptivity of the carbon. The latter was suggested to be caused by changes in the adsorption properties of the unburned char and a decreased formation of soot, which was found to have a large AEA...

Using locally available fly ash for modifying concrete properties

International Nuclear Information System (INIS)

Rizwan, S.A.; Toor, S.R.; Ahmad, H.

2005-01-01

This paper suggests the possible use of fly ash, a bye-product produced in our thermal power plants operating on coal as fuel for improvement of concrete quality. In the present investigation, locally available finely divided fly ash has been used for modification Presently, it is being used extensively in concrete in modem countries and is considered as waste material in general. Behavior of fly ash modified concrete in comparison to normal concrete having same mix proportions, aggregates, net water-cement ratio and similar curing conditions has been studied in short terms up to the age of 56 days during which the specimens were subjected to normal water curing method. Tests were carried out for compressive strength at 3, 7, 14,28 and 56 days, 24 hours % age water absorption at the age of 56 days and durability (resistance of concrete against N/2 solutions of both nitric acid and hydrochloric acid for one month) of concrete were also carried out at the age of 56 days. It was seen that the compressive strength of concrete modified with the available type of fly ash was less than the normal concrete. But so. far as the durability and % age water absorption are concerned, fly ash plays an important role here. 24 hours % age water absorption decreases with increase in fly ash content an admixture and as a cement replacement in concrete. But so far as durability is concerned, 20% replacement of fly ash with cement appears to be more effective than it is with 40%. The purpose of investigation was to introduce the use of fly ash in concretes to the Engineers and Architects in Pakistan. (author)

Fuel Pellets Production from Biodiesel Waste

Directory of Open Access Journals (Sweden)

Kawalin Chaiyaomporn

2010-01-01

Full Text Available This research palm fiber and palm shell were used as raw materials to produce pelletised fuel, and waste glycerol were used as adhesive to reduce biodiesel production waste. The aim of this research is to find optimum ratio of raw material (ratio of palm fiber and palm shell, raw material size distribution, adhesive temperature, and ratio of ingredients (ratio of raw material, waste glycerol, and water. The optimum ratio of pelletized fuel made only by palm fiber was 50:10:40; palm fiber, water, and waste glycerol respectively. In the best practice condition; particle size was smaller than 2 mm, adhesive glycerol was heated. From the explained optimum ratio and ingredient, pelletizing ratio was 62.6%, specific density was 982.2 kg/m3, heating value was 22.5 MJ/kg, moisture content was 5.9194%, volatile matter was 88.2573%, fix carbon content was 1.5894%, and ash content was 4.2339% which was higher than the standard. Mixing palm shell into palm fiber raw material reduced ash content of the pellets. The optimum raw material ratio, which minimizes ash content, was 80 to 20 palm fiber and palm shell respectively. Adding palm shell reduced ash content to be 2.5247% which was higher than pelletized fuel standard but followed cubed fuel standard. At this raw material ratio, pelletizing ratio was 70.5%, specific density was 774.8 kg/m3, heating value was 19.71 MJ/kg, moisture content was 9.8137%, volatile matter was 86.2259%, fix carbon content was 1.4356%, and compressive force was 4.83 N. Pelletized fuel cost at optimum condition was 1.14 baht/kg.

THE COMPRESSIVE AND FLEXURAL STRENGTHS OF SELF-COMPACTING CONCRETE USING RAW RICE HUSK ASH

Directory of Open Access Journals (Sweden)

MD NOR ATAN

2011-12-01

Full Text Available This study investigates the compressive and flexural strengths of self-compacting concrete incorporating raw rice husk ash, individually and in combination with other types of mineral additives, as partial cement replacement. The additives paired with raw rice husk ash were fine limestone powder, pulverized fuel ash and silica fumes. The mix design was based on the rational method where solid constituents were fixed while water and superplasticizer contents were adjusted to produce optimum viscosity and flowability. All mixes were designed to achieve SF1 class slump-flow with conformity criteria ≥ 520 mm and ≤ 700 mm. Test results show that 15% replacement of cement using raw rice husk ash produced grade 40 concrete. It was also revealed that 30% and 45% cement replacements using raw rice husk ash combined with limestone powder and raw rice husk ash combined with limestone powder and silica fume respectively, produced comparable compressive strength to normal concrete and improved flexural strengths.

Engineering Behavior and Characteristics of Wood Ash and Sugarcane Bagasse Ash

Directory of Open Access Journals (Sweden)

Francisco Grau

2015-10-01

Full Text Available Biomasses are organic materials that are derived from any living or recently-living structure. Plenty of biomasses are produced nationwide. Biomasses are mostly combusted and usually discarded or disposed of without treatment as biomass ashes, which include wood and sugarcane bagasse ashes. Thus, recycling or treatment of biomass ashes leads to utilizing the natural materials as an economical and environmental alternative. This study is intended to provide an environmental solution for uncontrolled disposal of biomass ashes by way of recycling the biomass ash and replacing the soils in geotechnical engineering projects. Therefore, in this study, characteristic tests of wood and sugarcane bagasse ashes that are considered the most common biomass ashes are conducted. The test of chemical compositions of biomass ashes is conducted using energy dispersive X-ray spectroscopy (EDS, and Scanning Electron Microscope (SEM, and heavy metal analysis is also conducted. Engineering behaviors including hydraulic conductivity, constrained modulus and shear modulus are examined. Also, coal fly ash Class C is used in this study for comparison with biomass ashes, and Ottawa 20/30 sands containing biomass ashes are examined to identify the soil replacement effect of biomass ashes. The results show that the particle sizes of biomass ashes are halfway between coal fly ash Class C and Ottawa 20/30 sand, and biomass ashes consist of a heterogeneous mixture of different particle sizes and shapes. Also, all heavy metal concentrations were found to be below the US Environmental Protection Agency (EPA maximum limit. Hydraulic conductivity values of Ottawa 20/30 sand decrease significantly when replacing them with only 1%–2% of biomass ashes. While both the constrained modulus and shear modulus of biomass ashes are lower than Ottawa 20/30 sand, those of mixtures containing up to 10% biomass ashes are little affected by replacing the soils with biomass ashes.

A Comprehensive Review on the Properties of Coal Bottom Ash in Concrete as Sound Absorption Material

Directory of Open Access Journals (Sweden)

Ramzi Hannan Nurul Izzati Raihan

2017-01-01

Full Text Available The government is currently implementing policies to increase the usage of coal as fuel for electricity generation. At the same time, the dependency on gas will be reduced. In addition, coal power plants in Malaysia produce large amounts of industrial waste such as bottom ash which is collected in impoundment ponds (ash pond. However, millions of tons of coal ash (bottom ash waste are collected in ponds near power plant stations. Since bottom ash has been classified as hazardous material that threatens the health and safety of human life, an innovative and sustainable solution has been introduced to reuse or recycle industrial waste such as coal bottom ash in concrete mixtures to create a greener and more sustainable world. Bottom ash has the potential to be used as concrete material to replace fine aggregates, coarse aggregates or both. Hence, this paper provides an overview of previous research which used bottom ash as fine aggregate replacement in conventional concrete. The workability, compressive strength, flexural strength, and sound absorption of bottom ash in concrete are reviewed.

Fuel characterization requirements for cofiring biomass in coal-fired boilers

International Nuclear Information System (INIS)

Prinzing, D.E.; Tillman, D.A.; Harding, N.S.

1993-01-01

The cofiring of biofuels with coal in existing boilers, or the cofiring of biofuels in combined cycle combustion turbine (CCCT) systems presents significant potential benefits to utilities, including reductions in SO 2 and NO x emissions as a function of reducing the mass flow of sulfur and nitrogen to the boiler, reducing CO 2 emissions from the combustion of fossil fuels; potentially reducing fuel costs both by the availability of wood residues and by the fact that biofuels are exempt from the proposed BTU tax; and providing support to industrial customers from the forest products industry. At the same time, cofiring requires careful attention to the characterization of the wood and coal, both singly and in combination. This paper reviews characterization requirements associated with cofiring biofuels and fossil fuels in boilers and CCCT installations with particular attention not only to such concerns as sulfur, nitrogen, moisture, and Btu content, but also to such issues as total ash content, base/acid ratio of the wood ash and the coal ash, alkali metal content in the wood ash and wood fuel (including converted fuels such as low Btu gas or pyrolytic oil), slagging and fouling indices, ash fusion temperature, and trace metal contents in the wood and coal. The importance of each parameter is reviewed, along with potential consequences of a failure to adequately characterize these parameters. The consequences of these parameters are reviewed with attention to firing biofuels with coal in pulverized coal (PC) and cyclone boilers, and firing biofuels with natural gas in CCCT installations

Ash partitioning during the oxy-fuel combustion of lignite and its dependence on the recirculation of flue gas impurities (H{sub 2}O, HCl and SO{sub 2})

Energy Technology Data Exchange (ETDEWEB)

Facun Jiao; Juan Chen; Lian Zhang; Yajuan Wei; Yoshihiko Ninomiya; Sankar Bhattacharya; Hong Yao [Monash University, Clayton, Vic. (Australia). Department of Chemical Engineering

2011-06-15

Oxy-fuel combustion of a brown coal (i.e. lignite) has been carried out at 1000{sup o}C to experimentally examine the vaporisation of organically bound metals and the agglomeration of ash particles as a function of the concentration of gaseous impurities including H{sub 2}O, HCl and SO{sub 2} in about 27% O{sub 2} balanced with CO{sub 2}. The properties of bulk ash and individual metals were investigated intensively. Particularly, attention was paid to Na which is notorious for fouling and to organically bound Al which has been less studied. The results indicate that, the organically bound metals, although possessing a very low content in the raw coal, are vital for the agglomeration of ash particles, which are also highly sensitive to the loading of gas impurities in flue gas. HCl recirculation is the most crucial factor promoting the vaporisation of metals via chlorination. Apart from alkali metals, the organically bound Al and Ti were also vaporised noticeably. Recirculation of SO{sub 2} promoted the sulfation of Na to condense into liquid droplet which increased fine ash yield. Co-existence of bulk HCl and SO{sub 2} played a synergetic role in the sulfation of Na via an initial chlorination of the char-bound Na. In contrast, co-existence of steam with HCl and SO{sub 2} favored the formation of Na alumino-silicates, which are favorable for ash agglomeration. 34 refs., 15 figs., 3 tabs.

Investigation of the particle size distribution and particle density characteristics of Douglas fir hogged fuel fly ash collected under known combustion conditions. Technical Progress Report No. 2

Energy Technology Data Exchange (ETDEWEB)

Lang, A.J.; Junge, D.C.

1978-12-01

The increased interest in wood as a fuel source, coupled with the increasing demand to control the emission generated by wood combustion, has created a need for information characterizing the emissions that occur for given combustion conditions. This investigation characterizes the carbon char and inorganic fly ash size and density distribution for each of thirty-eight Douglas fir bark samples collected under known conditions of combustion.

Microwave-assisted synthesis of geopolymers from fluidised bed gasifier bottom ash

CSIR Research Space (South Africa)

Oboirien, BO

2013-09-01

Full Text Available Fluidised bed gasification (FBG) is a clean coal technology suitable for power and fuel generation from low grade coals. However, the resulting bottom ash presents some disposal challenges to the power plants and the environment. The production...

Ash characteristics and plant nutrients in some aquatic biomasses

Science.gov (United States)

Masto, Reginald; Pandit, Ankita; George, Joshy; Mukhopadhyay, Sangeeta; Selvi, Vetrivel; Ram, Lal

2016-04-01

Aquatic biomasses are explored as potential fuel source for direct combustion because of their faster growth and no land requirement. The energy density and the ash characteristics of the aquatic biomasses are to be evaluated for their suitability for energy extraction. In the study, four aquatic plant samples namely Eichornia crassipes, Hydrilla verticilleta, Lemna minor, Spirogyra spp were collected from a pond in Digwadih Campus of Central Institute of Mining and Fuel Research, Dhanbad. The biomasses were air dried, powdered and ashed at different temperatures. Volatile C was relatively lower in Spirogyra and Hydrilla (53 %) than Eichornia (62.6 %) or Lemna (59.7 %), whereas fixed C was higher for Eichornia and Lemna (about 10 %) and lower for Hydrilla (1 %). Ultimate analysis showed that the carbon content was in the order Eichornia > Lemna > Spirogyra > Hydrilla. The IR spectra of each raw biomass is compared to their respective ashes obtained at different temperatures (500-900°C). With increase in ashing temperature from 500-900°C there is gradual breakdown of the cellulosic structure hence, peaks around 2900-2800cm-1 caused by aliphatic C-H vibration tends to disappear slowly in ash. More number of peaks appears at lower wavenumbers in ashes of all the biomass samples indicating towards increased percentage of inorganic ion species. Considerable enrichment of SiO2 is validated with prominent peaks at 1100-900 cm-1 in all the ashes. Lemna and Spirogyra has a similar ash composition (Si > Al > Ca > K), whereas, Ca was higher in Hydrilla (Si > Ca > K > Al). Eichornia (Si > K > Ca > Al) has higher K and Ca than Al. SiO2 and Al2O3 were higher in Spirogyra, while SiO2 and CaO in Eichornia and Hydrilla. K first increased from 500-700/800⁰C, and then decreased from 800-900⁰C. Cl is lost slowly in ash from 500-700/800⁰C and then by a drastic reduction from 800-900⁰C. S is enhanced in ash at all temperatures although the change is quite small. Most of the Cl

Assessing the environmental impact of ashes used in a landfill cover construction.

Science.gov (United States)

Travar, I; Lidelöw, S; Andreas, L; Tham, G; Lagerkvist, A

2009-04-01

Large amounts of construction materials will be needed in Europe in anticipation for capping landfills that will be closed due to the tightening up of landfill legislation. This study was conducted to assess the potential environmental impacts of using refuse derived fuel (RDF) and municipal solid waste incineration (MSWI) ashes as substitutes for natural materials in landfill cover designs. The leaching of substances from a full-scale landfill cover test area built with different fly and bottom ashes was evaluated based on laboratory tests and field monitoring. The water that drained off above the liner (drainage) and the water that percolated through the liner into the landfill (leachate) were contaminated with Cl(-), nitrogen and several trace elements (e.g., As, Cu, Mo, Ni and Se). The drainage from layers containing ash will probably require pre-treatment before discharge. The leachate quality from the ash cover is expected to have a minor influence on overall landfill leachate quality because the amounts generated from the ash covers were low, environmental view point, the placement of ashes in layers above the liner is more critical than within the liner.

Development of metabarcoding for tracking changes of soil fauna community under stress by application of ash

DEFF Research Database (Denmark)

Qin, J; de Groot, G.A.; Hansen, L. H.

Ash is a waste product from combustion of bio-fuel in power plants. Application of ash on soil ensures nutrient recycling, but detrimental ecotoxicological consequences may arise since ash is a complex mixture that may contain compounds affecting soil invertebrates and their food and habitat...... and species. DNA metabarcoding, which couples the principle of DNA barcoding with next generation sequencing technology, has the potential to simplify community diversity monitoring. However, sampling and DNA extraction methods for the purpose of soil microarthropod metabarcoding have not been yet fully...

Ash Utilisation 2012. Ashes in a Sustainable Society. Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-11-01

Conference themes: Risk assessment, Fly ash- Road construction, Recycling and Greenhouse gases, Storage of ashes, Fertilizer, Metal Mining, Support and Barriers, Construction Material, Civil Engineering, and MSWI bottom ash.

Ash and heavy metals in fluidized-bed combustion of wood wastes; Tuhka ja raskasmetallit puuperaeisen jaetteen kerrosleijupoltossa

Energy Technology Data Exchange (ETDEWEB)

Kaessi, T; Aittoniemi, P [IVO Power Engineering, Vantaa (Finland); Kauppinen, E; Latva-Somppi, J; Kurkela, J [VTT Chemical Technology, Espoo (Finland); Partanen, J [IVO Technology Centre, Vantaa (Finland)

1997-10-01

Ash formation and deposition mechanisms during co-combustion of pulp mill sludge and bark in industrial bubbling fluidized bed (BFB) combustor have been studied. Similar fuels were used in a bench-scale BFB for co-combustion of sludge and bark pellets and comparative studies with separate combustion of these fuels. Results indicated that in industrial scale unit significant fraction of ash had vaporization. About 14 mass-% of the total fly ash was found in the particle size below 0.2 {mu}m. The vaporized species consisted of potassium (K), sulfur (S), chlorine (Cl) and also of minor quantities of sodium (Na). In the benchscale similar vaporization fractions during co-combustion were measured, about 11 mass-%. During the combustion of bark this ratio, about 20 mass-%, was higher than during sludge combustion. The vaporized ash fraction was in the case of dried sludge combustion about 7 mass-%, but with wet sludge the vaporization rate was remarkably lower, about 1-2 mass-%. An increase in the bed temperature increased also ash vaporization. Test run period without combustion at elevated temperatures produced very low quantities of vaporized ash. The vaporized species in bench-scale test during bark pellet combustion were K, S and Cl, for sludge combustion also Na was clearly detected. No condensation of the vaporized species in bed area or furnace walls was observed. Bed defluidization was studied in the bench-scale unit. During bark pellet combustion the bed-agglomeration proceeded via small ash particle, below 2 {mu}m, coating on sand particle surface and consequent bonding between the ash layers. In the case of sludge combustion the accumulation of large ash particles and sintering of these porous agglomerates was observed to cause bed coarsening and defluidization. (orig.)

Sugarcane boiler ash as an amendment for soilless growing media

Science.gov (United States)

In 2016, research was conducted to investigate the use of sugarcane bagasse ash (SBA) as an amendment to soilless planting media for the production of vegetable seedlings. Typically, the eleven Louisiana sugarcane mills use a portion of the sugarcane bagasse for fuel, producing over 60,000 tons of S...

Characterisation and prediction of deposits in biomass co-combustion

NARCIS (Netherlands)

Tortosa Masiá, A.A.

2010-01-01

This PhD thesis deals with the theoretical, experimental and modeling work which was performed to study deposition during biomass and waste co-combustion in pulverised coal facilities. Fossil fuels dominate the current energy scenario. Increasing concerns about fossil fuels availability and about

Suitability of untreated wood ash for recycling; Qualitaet und Verwertungsmoeglichkeiten von Holzaschen aus naturbelassenen Hoelzern

Energy Technology Data Exchange (ETDEWEB)

Stahl, E. [Fraunhofer-Inst. fuer Umwelt-, Sicherheits- und Energietechnik, UMSICHT, Oberhausen (Germany); Doetsch, P. [RWTH Aachen (Germany). Lehr- und Forschungsgebiet Abfallwirtschaft

2008-10-15

Background, aim and scope: The increasing use of wood for generating heat and electricity requires that more and more fuels be obtained directly or indirectly from the forest. Sound, sustainable recycling management calls for the return of any generated wood ash back to the forest to make use of the nutrients it contains. Similarly, recycling this ash in other locations such as agricultural land or private gardens can serve equally well as fertilizer. At the same time, it is critical that no accumulated pollutants be introduced into the nutrient loop. Wood ash that is heavily laden with such pollutants must not be considered for recycling. As part of this research project, commissioned by the Ministry for the Environment and Conservation, Agriculture and Consumer Protection of the State of North Rhine-Westphalia in Germany (MUNLV), ash samples of 209 woodfired appliances generating between 10 and 4000 kW of heat performance were taken from throughout the federal state of North Rhine-Westphalia. Untreated wood, either forested or scrap, was used as the sole fuel for these appliances. Materials and methods: All course ash and fly ash samples were analyzed to determine their composition of main nutrients, heavy metals, and the elements Fe, Cl, Si, Al and Na. The purpose of this analysis was to evaluate the suitability of this wood ash for reintroduction to forest soils or as fertilizer in other types of soil. Results: The majority of the wood ash samples in this study contained sufficiently high amounts of nutrients to match the requirement for stand-alone fertilizers (PK-fertilizer, potash fertilizer). However, the heavy metal content was highly variable, with a mean content high enough to prohibit them from being classified per se as PK- or potash fertilizer for agricultural land. Due to the high quantities of cadmium, application of this ash to garden soils would likewise be ill-advised. Discussion: On forest soils German law permits application of a mixture of

Experimental Analysis of Fly Ash & Coir Fiber Mix Cement Concrete for Rigid Pavement

OpenAIRE

Er. Amit Kumar Ahirwar; Prof. Rajesh Joshi

2015-01-01

In India Thermal power plants which use pounded coal as a fuel, generates million tones of fly ash every year as a waste. Conservative clearance of this material which gets easily air-borne and constitutes a serious health hazards to the community, is an expensive operation. A part from this compacted fly ash can be used in embankments, road sub-bases and also for structural fills. The major drawbacks of such materials are their limited load carrying capacity and poor settlement c...

Biomass ash utilization

Energy Technology Data Exchange (ETDEWEB)

Bristol, D.R.; Noel, D.J.; O`Brien, B. [HYDRA-CO Operations, Inc., Syracuse, NY (United States); Parker, B. [US Energy Corp., Fort Fairfield, ME (United States)

1993-12-31

This paper demonstrates that with careful analysis of ash from multiple biomass and waste wood fired power plants that most of the ash can serve a useful purpose. Some applications require higher levels of consistency than others. Examples of ash spreading for agricultural purposes as a lime supplement for soil enhancement in Maine and North Carolina, as well as a roadbase material in Maine are discussed. Use of ash as a horticultural additive is explored, as well as in composting as a filtering media and as cover material for landfills. The ash utilization is evaluated in a framework of environmental responsibility, regulations, handling and cost. Depending on the chemical and physical properties of the biomass derived fly ash and bottom ash, it can be used in one or more applications. Developing a program that utilizes ash produced in biomass facilities is environmentally and socially sound and can be financially attractive.

Environmental implications of fossil-fuelled power stations

International Nuclear Information System (INIS)

Robson, A.

1979-01-01

The public health and environmental implications of electricity generation by fossil-fuelled power stations are discussed with respect to pollutant emission and the disposal of waste products. The following conclusions were deduced. The policy of using tall chimney stacks has ensured that acceptable concentrations of potential pollutants are observed in the vicinity of power stations. Large scale carbon dioxide emission may represent a problem in the future due to its effect on the climate. The effects of sulphur dioxide and the oxides of nitrogen need to be kept under review but it is likely that sources other than power stations will be of greater importance in this context. Pulverised fuel ash is a safe and useful by product of power production. Finally the radiation dose to man caused by the release of naturally occurring radioisotopes is negligible compared to the natural background levels. (UK)

Investigation of rye straw ash sintering characteristics and the effect of additives

International Nuclear Information System (INIS)

Wang, Liang; Skreiberg, Øyvind; Becidan, Michael; Li, Hailong

2016-01-01

Highlights: • Rye straw ash has a high sintering tendency at elevated temperatures. • Addition of additive increases melting temperature of the rye straw ash. • Kaolin addition leads to formation of silicates binding K in the ash. • Calcite and Ca-sludge promotes formation of silicates and phosphates in the ash. • Calcite addition restrains attaching and accumulation of rye straw ash melts. - Abstract: The understanding of ash sintering during combustion of agricultural residues is far from complete, because of the high heterogeneity of the content and composition of ash forming matters and the complex transformation of them. In order to make agricultural residues competitive fuels on the energy market, further research efforts are needed to investigate agricultural residues’ ash sintering behavior and propose relevant anti-sintering measures. The aim of this work was to investigate the ash characteristics of rye straw and effects of additives. Three additives were studied regarding their abilities to prevent and abate rye straw ash sintering. Standard ash fusion characterization and laboratory-scale sintering tests were performed on ashes from mixtures of rye straw and additives produced at 550 °C. Ash residues from sintering tests at higher temperatures were analyzed using a combination of X-ray diffraction (XRD) and scanning electron microscopy–energy dispersive X-ray spectrometry (SEM–EDX). High sintering and melting tendency of the rye straw ash at elevated temperatures was observed. Severe sintering of the rye straw ash was attributed to the formation and fusion of low temperature K–silicates and K–phosphates with high K/Ca ratios. Among the three additives, calcite served the best one to mitigate sintering of the rye straw ash. Ca from the calcite promoted formation of high temperature silicates and calcium rich K–phosphates. In addition, calcite may hinder aggregating of ash melts and further formation of large ash slag. Therefore

Ash and burn control through fishbones

Energy Technology Data Exchange (ETDEWEB)

Varadarajan, V.; Miley, G.H.

1989-01-01

The thermal alphas will accumulate in the center of the ignited thermonuclear plasma in the long pulse experiments. This accumulation increases the Z{sub eff} leading to increased synchrotron losses and decreases the effective fuel density which reduces the power output. Also the ignited plasma is burn-unstable and its temperature is expected to increase above the design point until a stable equilibrium is reached at a higher temperature. This higher operating temperature is not expected to be beneficial. Thus we are faced with the dual problem of ash accumulation and thermonuclear burn instability in the steadily burning tokamak plasma. So some means of controlling them is desirable. Several control schemes for both problems have been proposed. But it is felt that we need alternatives with more desirable characteristics. In this paper, we explore the use of fishbones' as possible scheme that will achieve the dual purpose of ash and burn control. 3 refs.

On the non-linear nature of the variation, with intensity, of high energy cathode sputtering, and the variation of the latter with temperature (1960); Sur le caractere non lineaire en fonction de l'intensite de la pulverisation cathodique a haute energie et sa variation en fonction de la temperature (1960)

Energy Technology Data Exchange (ETDEWEB)

Cassignol, C; Ranc, G [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1960-07-01

A new cathode sputtering theory at high energy is presented which has been elaborated in taking in account the non-linearity of this phenomenon with the density of the impinging ions. This theory allows to predict the influence of target temperature on the rate of cathode sputtering. This influence is experimentally demonstrated. (author) [French] On presente, au sujet de la pulverisation cathodique a haute energie, une theorie qui tient compte de la non-linearite de la variation de ce phenomene avec la densite des ions incidents. Cette theorie permet de predire l'influence de la temperature de la cible sur la vitesse de pulverisation cathodique. On demontre l'existence de cette influence par une methode experimentale. (auteur)

Material Analysis of Bottom Ash from Waste-to-Energy Plants.

Czech Academy of Sciences Publication Activity Database

Šyc, Michal; Krausová, Aneta; Kameníková, Petra; Šomplák, R.; Pavlas, M.; Zach, Boleslav; Pohořelý, Michael; Svoboda, Karel; Punčochář, Miroslav

2018-01-01

Roč. 73, MAR 2018 (2018), s. 360-366 ISSN 0956-053X R&D Projects: GA TA ČR TE02000236 Institutional support: RVO:67985858 Keywords : bottom ash * urban mining * metals recovery Subject RIV: JE - Non-nuclear Energetics, Energy Consumption ; Use OBOR OECD: Energy and fuels Impact factor: 4.030, year: 2016

Ash chemistry and behavior in advanced co-combustion

Energy Technology Data Exchange (ETDEWEB)

Hupa, M; Skrifvars, B J [Aabo Akademi, Turku (Finland). Combustion Chemistry Research Group

1997-10-01

The purpose of this LIEKKI 2 project is to report results achieved within the EU/JOULE/OPTEB project to the Finnish combustion research community through the LIEKKI program. The purpose of the EU/JOULE/OPTEB project is to find prediction methods for evaluating ash behavior, such as slagging, fouling and corrosion propensity, in full scale combustion systems through chemical or mineralogical analyses, intelligent laboratory tests and chemistry calculations. The project focuses on coals, coal mixtures and coal biomass mixtures fired in advanced combustion systems, such as fluidized bed boilers, pulverized fuel boilers with critical steam values etc. The project will make use of (1) advanced multi-component combustion equilibrium calculations, (2) ash sintering tendency laboratory tests and (3) chemical evaluations of slagging, fouling and corrosion measurements in full scale units. (orig.)

Modeling of reactive chemical transport of leachates from a utility fly-ash disposal site

International Nuclear Information System (INIS)

Apps, J.A.; Zhu, M.; Kitanidis, P.K.; Freyberg, D.L.; Ronan, A.D.; Itakagi, S.

1991-04-01

Fly ash from fossil-fuel power plants is commonly slurried and pumped to disposal sites. The utility industry is interested in finding out whether any hazardous constituents might leach from the accumulated fly ash and contaminate ground and surface waters. To evaluate the significance of this problem, a representative site was selected for modeling. FASTCHEM, a computer code developed for the Electric Power Research Institute, was utilized for the simulation of the transport and fate of the fly-ash leachate. The chemical evolution of the leachate was modeled as it migrated along streamtubes defined by the flow model. The modeling predicts that most of the leachate seeps through the dam confining the ash pond. With the exception of ferrous, manganous, sulfate and small amounts of nickel ions, all other dissolved constituents are predicted to discharge at environmentally acceptable concentrations

Development of novel ash hybrids to introgress resistance to emerald ash borer into north American ash species

Science.gov (United States)

Jennifer L. Koch; David W. Carey; Mary E. Mason

2008-01-01

Currently, there is no evidence that any of the native North American ash species have any resistance to the emerald ash borer (EAB). This means that the entire ash resource of the eastern United States and Canada is at risk of loss due to EAB. In contrast, outbreaks of EAB in Asian ash species are rare and appear to be isolated responses to stress (Bauer et al. 2005,...

Silica from Ash

Indian Academy of Sciences (India)

management, polymer composites and chemical process design. Figure 1 Difference in color of the ash ... The selection of ash is important as the quality of ash determines the total amount as well as quality of silica recoverable Ash which has undergone maximum extent of combustion is highly desirable as it contains ...

A database for the program 'Environmentally correct utilization of ashes'; Databas inom delprogrammet 'Miljoeriktig anvaendning av askor'

Energy Technology Data Exchange (ETDEWEB)

Bjurstroem, Henrik; Rydstrand, Camilla; Berg, Magnus; Wikman, Karin [AaF-Energi and Miljoe AB, Stockholm (Sweden)

2004-01-01

In the program 'Environmentally correct utilization of ashes' that is active 2002-2005 at the Swedish Thermal Research Institute (Vaermeforsk), R and D studies of the properties of ashes or combustion residues are being carried out and will be carried out. It may be difficult to obtain an overview of these data if these are dispersed in a large number of reports. These data are valuable as they may be used as references on the properties of ashes (these do vary widely, and knowledge of the range within which they vary as well of as the cause to effect chain is far from exhaustive). They also form a basis for continued work in this area. Furthermore, one of the aims of the R and D program is to define criteria for the use of ashes in various situations. Such criteria are generally formulated using quantitative requirements on technical as well as environmental properties. A flexible database has been created in Access in order to store these data on ashes as an easy-to-access reference. The goal was satisfaction of both a user of ashes and a producer of ashes. The information that can be stored stretches from the fuel, the design of the combustion plant to properties specific to a given utilization such as shear module or permeability. Attention has especially been paid to the facts that fuels are often mixed and that ashes are often mixed with other ashes or with other materials. In this first stage, data have been stored in the database for 22 ash samples that have been studied in eight R and D projects.

Sulphation of oil shale ash under atmospheric and pressurized combustion conditions

International Nuclear Information System (INIS)

Kuelaots, I.; Yrjas, P.; Hupa, M.; Ots, A.

1995-01-01

One of the main problems in conventional combustion boilers firing pulverized oil shale is the corrosion and fouling of heating surfaces, which is caused by sulphur compounds. Another major problem, from the environmental point of view, are the high SO 2 emissions. Consequently, the amount of sulphur in flue gases must be reduced. One alternative to lower the SO 2 , concentration is the use of new technologies, such as pressurized fluidized bed combustion (PFBC). In FBC processes, the sulphur components are usually removed by the addition of limestone (CaCO 3 ) or dolomite (CaCO 3 x MgCO 3 ) into the bed. The calcium in these absorbents react with SO 2 , producing solid CaSO 4 . However, when burning oil shale, there would be no need to add limestone or dolomite into the bed, due to the initially high limestone content in the fuel (molar ratio Ca/S =10). The capture of sulphur by oil shale ashes has been studied using a pressurized thermogravimetric apparatus (PTGA). The chosen experimental conditions were typical for atmospheric and pressurized fluidized bed combustion. Four different materials were tested - one cyclone ash from an Estonian oil shale boiler, two size fractions of Estonian oil shale and, one fraction of Israeli oil shale. The cyclone ash was found to be the poorest sulphur absorbent. In general, the results from the sulphur capture experiments under both atmospheric and pressurized fluidized bed conditions showed that the oil shale can capture not only its own sulphur but also significant amounts of additional sulphur from another fuel if the fuels are mixed together. (author)

Oxy-fuel combustion of solid fuels

DEFF Research Database (Denmark)

Toftegaard, Maja Bøg; Brix, Jacob; Jensen, Peter Arendt

2010-01-01

Oxy-fuel combustion is suggested as one of the possible, promising technologies for capturing CO2 from power plants. The concept of oxy-fuel combustion is removal of nitrogen from the oxidizer to carry out the combustion process in oxygen and, in most concepts, recycled flue gas to lower the flame...... provide additional options for improvement of process economics are however likewise investigated. Of particular interest is the change of the combustion process induced by the exchange of carbon dioxide and water vapor for nitrogen as diluent. This paper reviews the published knowledge on the oxy......-fuel process and focuses particularly on the combustion fundamentals, i.e. flame temperatures and heat transfer, ignition and burnout, emissions, and fly ash characteristics. Knowledge is currently available regarding both an entire oxy-fuel power plant and the combustion fundamentals. However, several...

A case study of the long-term retention of 137Cs after inhalation of high temperature reactor fuel element ash.

Science.gov (United States)

Froning, M; Kozielewski, T; Schläger, M; Hill, P

2004-01-01

In 1987, a worker was internally contaminated with 137Cs as a result of an accident during the handling of high temperature reactor fuel element ash. In the long-term follow-up monitoring an unusual retention behaviour was found. The observed time dependence of caesium retention does not agree with the standard models of ICRP Publication 30. The present case can be better explained by assuming an intake of a mixture of type F and type S compounds. However, experimental data can be best described by a four-exponential retention function with two long-lived components, which was used as an ad hoc model for dose calculation. The resulting dose is compared with doses calculated on the basis of ICRP Publication 66.

Temporal evolution of wildfire ash and its implications for water pollution

Science.gov (United States)

Santin, Cristina; Doerr, Stefan H.; Otero, Xose L.; Chafer, Chris J.

2015-04-01

Ash, the burnt residue generated from combustion of vegetation, litter and surface soil, covers the ground after every wildfire. The effects of wildfire ash on the post-fire landscape are many and very diverse. It is a source of nutrients and can, therefore, help the recovery of vegetation after fire. Furthermore, in its initial state, the ash layer on the ground can protect the bare soil from rain splash erosion and can act as an adsorbent layer, preventing or delaying post-fire water erosion by runoff. However, when the adsorbent capability of the ash layer is exceeded, this highly erodible material can be transported into the hydrological network and be a major contributor to water contamination. Most previous studies on post-fire erosion and water contamination have focused on soil erosion and associated sediment transfer and overlooked the ash component or, when considered, ash has been included as an unidentified part of the eroded sediment. One of the reasons for overlooking this key post-fire component is the difficulty of ash sampling before it is lost by wind or water erosion or altered by aging on-site. Here we compare the water contamination potential of ash obtained from two fires in the dry eucalyptus forest environment of the Sydney tablelands, Australia: i) 'aged ash' produced during the severe Balmoral wildfire and sampled two months after the event (Jan. 2014) and ii) 'fresh ash' sampled immediately after a high-intensity experimental fire in the same region (Sept. 2014). At the time of sampling, neither of the ash types had been affected by water erosion, however, the aged ash had been subjected to rainfall events and, potentially, to wind erosion during the two months of exposure. Vegetation type, fuel loads and fire severity, determined using remote sensing and on-site observations, were comparable between both areas sampled. Ash physicochemical properties differed, with 'fresh ash' having higher pH and EC values and higher concentration of

Performance of diesel particulate filter catalysts in the presence of biodiesel ash species

DEFF Research Database (Denmark)

Hansen, Brian Brun; Jensen, Anker Degn; Jensen, Peter Arendt

2013-01-01

The utilization of bio-fuels, such as biodiesel, is expected to contribute significantly towards the planned 10% of renewable energy within the EU transport sector by 2020. Increased biodiesel blend percentages may change engine exit flue gas ash composition and affect the long-term performance...... of cleaning technologies, such as oxidation catalysts and diesel particulate filters. In this work the performance of a commercial catalyst has been studied for conversion of diesel particulate matter (SRM 2975) at 10% O2, in the presence of salts simulating ash species derived from engine oil and biodiesel...... the temperature at which the oxidation rate peaked from 662 ± 1 °C to 526 ± 19 °C. The introduction of biodiesel ash species such as Na2CO3, K2CO3 or K3PO4 decreased the peak conversion temperature further (422 ± 12; 404 ± 4 and 423 ± 7 °C), with a limited dependence on ash concentration. A deterioration...

Properties of palm oil fuel ash cement sand brick containing pulverized cockle shell as partial sand replacement

Science.gov (United States)

Mat Aris, S.; Muthusamy, K.; Uzer, A.; Ahmad, S. Wan

2018-04-01

Environmental pollution caused by the disposal of solid wastes generated from both palm oil industry and cockle shell trade has motivated researches to explore the potential of these wastes. Integrating these wastes in production of construction material is one of the ways to reduce amount of waste thrown at dumping area. Thus, the present investigation investigates the performance of palm oil fuel ash (POFA) cement sand brick containing pulverized cockle shell as partial fine aggregate replacement. All mixes used contain 20% of POFA as partial cement replacement. Total of six mixes were prepared by adding a range of pulverized cockle shell that is 0%, 10%, 20%, 30%, 40% and 50% as partial sand replacement. The mixes were prepared in form of brick. All the water cured samples were tested for compressive strength and flexural strength until 28 days. Findings show that brick produced using 20% pulverized cockle shell exhibit the highest compressive strength and flexural strength also the lowest water absorption value.

Effect of secondary fuels and combustor temperature on mercury speciation in pulverized fuel co-combustion: part 1

Energy Technology Data Exchange (ETDEWEB)

Shishir P. Sable; Wiebren de Jong; Ruud Meij; Hartmut Spliethoff [Delft University Technology, Delft (Netherlands). Section Energy Technology, Department of Process and Energy

2007-08-15

The present work mainly involves bench scale studies to investigate partitioning of mercury in pulverized fuel co-combustion at 1000 and 1300{sup o}C. High volatile bituminous coal is used as a reference case and chicken manure, olive residue, and B quality (demolition) wood are used as secondary fuels with 10 and 20% thermal shares. The combustion experiments are carried out in an entrained flow reactor with a fuel input of 7-8 kWth. Elemental and total gaseous mercury concentrations in the flue gas of the reactor are measured on-line, and ash is analyzed for particulate mercury along with other elemental and surface properties. Animal waste like chicken manure behaves very differently from plant waste. The higher chlorine contents of chicken manure cause higher ionic mercury concentrations whereas even with high unburnt carbon, particulate mercury reduces with increase in the chicken manure share. This might be a problem due to coarse fuel particles, low surface area, and iron contents. B-wood and olive residue cofiring reduces the emission of total gaseous mercury and increases particulate mercury capture due to unburnt carbon formed, fine particles, and iron contents of the ash. Calcium in chicken manure does not show any effect on particulate or gaseous mercury. It is probably due to a higher calcium sulfation rate in the presence of high sulfur and chlorine contents. However, in plant waste cofiring, calcium may have reacted with chlorine to reduce ionic mercury to its elemental form. According to thermodynamic predictions, almost 50% of the total ash is melted to form slag at 1300{sup o}C in cofiring because of high calcium, iron, and potassium and hence mercury and other remaining metals are concentrated in small amounts of ash and show an increase at higher temperatures. No slag formation was predicted at 1000{sup o}C. 24 refs., 8 figs., 4 tabs.

Wildfire Ash: Chemical Composition, Ash-Soil Interactions and Environmental Impacts

Science.gov (United States)

Brook, Anna; Hamzi, Seham; Wittenberg, Lea

2015-04-01

produced ash has significant and not always constructive pedological, ecological, hydrological and geomorphological effects and impacts (Shakesby, 2011). Abundant scientific information is assembled either from control fires by collecting samples before and after wildfire event, or conducting laboratory experiments exanimating data under truly isolated conditions (Lugassi et al., 2013). However, an integration and synthesis of the knowledge about ash including deeper understanding of inter-correlation between chemical, physical and morphological compounds in open post-burn environment and its possible interactions in soil formation or impact on soil composition are highly needed. The main aim of the presented study was to advance the science of soil-fire relationship by recognizing the remains ash as a new soil-forming factor, on par with the traditionally recognized factors: parent material, topography, time, climate, organisms, and recently recognized human activity as the sixth factor. This research was conducted to develop new methods to assess impacts and quantify the contributions/influences of post-fire products, mainly ash, on soil composition and soil properties in post-burned environment. We conducted several controlled experiments using 40 soil samples (typical Mediterranean Rendzina soil, pH 6.84, a grayish-brown, humus- and free calcium carbonate- rich, intra-zonal). The samples include bare soils and different types and loads of forest litter, were exposed to different temperatures (200° C, 400° C and 600° C) in a muffle furnace for 2 hours (Pereira et al. 2011) as fire temperature plays a key role in determining ash properties. The ash produced at a low temperatures (50% carbon and retains many of the structural characteristics of the parent material. At higher temperatures, the residue ash is greyish, consisted of very fine particles that preserve almost none of the original structural characteristics of the fuel (Woods and Balfour, 2008) creating

Effect of Selected Alternative Fuels and Raw Materials on the Cement Clinker Quality

Directory of Open Access Journals (Sweden)

Strigáč Július

2015-11-01

Full Text Available The article deals with the study of the effects of alternative fuels and raw materials on the cement clinker quality. The clinker quality was expressed by the content of two principal minerals alite C3S and belite C2S. The additions of alternative fuels ashes and raw materials, in principle, always increased the belite content and conversely reduced the amount of alite. The alternative fuels with high ash content were used such as the meat-bone meal, sewage sludge from sewage treatment plants and paper sludge and the used alternative raw materials were metallurgical slags - granulated blastfurnace slag, air cooled blastfurnace slag and demetallized steel slag, fluidized bed combustion fly ash and waste glass. Meat-bone meal, sewage sludge from sewage treatment plants and paper sludge were evaluated as moderately suitable alternative fuels which can be added in the amounts of 2.8 wt. % addition of meat-bone meals ash, 3.64 wt. % addition of sewage sludge ash and 3.8 wt. % addition of paper sludge ash to the cement raw mixture. Demetallised steel slag is suitable for production of special sulphate resistant cement clinker for CEM I –SR cement with addition up to 5 wt. %. Granulated blastfurnace slag is a suitable alternative raw material with addition 4 wt. %. Air cooled blastfurnace slag is a suitable alternative raw material with addition 4.2 wt. %. Waste glass is not very appropriate alternative raw material with addition only 1.16 wt. %. Fluidized bed combustion fly ash appears not to be equally appropriate alternative raw material for cement clinker burning with less potential utilization in the cement industry and with addition 3.41 wt. %, which forms undesired anhydrite CaSO4 in the cement clinker.

Cementing Efficiency of Low Calcium Fly Ash in Fly Ash Concretes

OpenAIRE

T. D. Gunneswara Rao; Mudimby Andal

2014-01-01

Research on the utilization of fly ash will no longer refer the fly ash as a waste material of thermal power plants. Use of fly ash in concrete making, makes the concrete economical as well as durable. The fly ash is being added to the concrete in three ways namely, as partial replacement to cement, as partial replacement to fine aggregates and as admixture. Addition of fly ash to the concrete in any one of the form mentioned above, makes the concrete more workable and durable than the conven...

Thermal co-treatment of combustible hazardous waste and waste incineration fly ash in a rotary kiln.

Science.gov (United States)

Huber, Florian; Blasenbauer, Dominik; Mallow, Ole; Lederer, Jakob; Winter, Franz; Fellner, Johann

2016-12-01

As current disposal practices for municipal solid waste incineration (MSWI) fly ash are either associated with significant costs or negative environmental impacts, an alternative treatment was investigated in a field scale experiment. Thereto, two rotary kilns were fed with hazardous waste, and moistened MSWI fly ash (water content of 23%) was added to the fuel of one kiln with a ratio of 169kg/Mg hazardous waste for 54h and 300kg/Mg hazardous waste for 48h while the other kiln was used as a reference. It was shown that the vast majority (>90%) of the inserted MSWI fly ash was transferred to the bottom ash of the rotary kiln. This bottom ash complied with the legal limits for non-hazardous waste landfills, thereby demonstrating the potential of the investigated method to transfer hazardous waste (MSWI fly ash) into non-hazardous waste (bottom ash). The results of a simple mixing test (MSWI fly ash and rotary kiln bottom ash have been mixed accordingly without thermal treatment) revealed that the observed transformation of hazardous MSWI fly ash into non-hazardous bottom ash during thermal co-treatment cannot be referred to dilution, as the mixture did not comply with legal limits for non-hazardous waste landfills. For the newly generated fly ash of the kiln, an increase in the concentration of Cd, K and Pb by 54%, 57% and 22%, respectively, was observed. In general, the operation of the rotary kiln was not impaired by the MSWI fly ash addition. Copyright © 2016 Elsevier Ltd. All rights reserved.

Emerald ash borer biocontrol in ash saplings: the potential for early stage recovery of North American ash

Science.gov (United States)

In many parts of North America, ash stands have been reduced by the emerald ash borer (Agrilus planipennis) invasion to a few surviving mature trees and young basal sprouts, saplings, and seedlings. Without a seed bank, ash tree recovery will require survival and maturation of these younger cohorts...

Technology for the Recovery of Fuel and Adsorbent Carbons from Coal Burning Utility Ash Ponds and Landfills

Energy Technology Data Exchange (ETDEWEB)

J.G. Groppo; T.L. Robl

2005-09-30

marketable lightweight aggregate and recover a high-grade fuel product. Spiral concentration provided acceptable grade lightweight aggregate with yields of only 10 to 20%. Incorporating a sieve bend into the process to recover coarse, porous ash particles from the outside race of the spirals increased aggregate yield to as high as 75%, however, the carbon content of the aggregate also increased. An opening size of 28 mesh on the sieve bend appeared to be sufficient. Lightweight concrete blocks (28 to 32 lbs) were produced from bottom ash and results show that acceptable strength could be attained with a cement/concrete ratio as low as 1/4. A mobile Proof-of-Concept (POC) field unit was designed and fabricated to meet the processing objectives of the project. The POC plant consisted of two trailer-mounted modules and was completely self sufficient with respect to power and water requirements. The POC unit was hauled to Coleman Station and operated at a feed rate of 2 tph. Results showed that the spirals operated similarly to previous pilot-scale operations and a 500 lb composite sample of coarse carbon was collected with a grade of 51.7% C or 7279 Btu/lb. Flotation results compared favorably with release analysis and 500 lbs of composite froth product was collected with a grade of 35% C or 4925 Btu/lb. The froth product was dewatered to 39% moisture with vacuum filtration. Pan pelletization and briquetting were evaluated as a means of minimizing handling concerns. Rotary pan pelletization produced uniform pellets with a compressive strength of 4 lbf without the use of any binder. Briquettes were produced by blending the coarse and fine carbon products at a ratio of 1:10, which is the proportion that the two products would be produced in a commercial operation. Using 3% lime as a binder produced the most desirable briquettes with respect to strength, attrition and drop testing. Additionally, the POC carbon products compared favorably with commercial activated carbon when used

Hydrothermal treatment of grape marc for solid fuel applications

International Nuclear Information System (INIS)

Mäkelä, Mikko; Kwong, Chi Wai; Broström, Markus; Yoshikawa, Kunio

2017-01-01

Highlights: • The effects of treatment temperature and liquid pH on char and liquid properties. • Liquid pH had a statistically significant effect only on liquid carbon yield. • Higher treatment temperature increased char volatiles that can enhance ignitability. • Char showed promising fuel properties if elevated ash phosphorus can be tolerated. - Abstract: The treatment and disposal of grape marc, a residue from grape processing, represents a significant economic and environmental challenge for the winemaking industry. Hydrothermal treatment of grape marc could be an efficient way for producing solid fuels on-site at the wineries. In this work the effects of treatment temperature and liquid pH on grape marc char and liquid properties were determined based on laboratory experiments and the combustion characteristics of char were assessed through thermogravimetric analysis and fuel ash classification. The results showed that hydrothermal treatment increased the energy and carbon contents and decreased the ash content of grape marc. The effect of liquid pH was statistically significant (p < 0.05) only for the determined carbon yield of liquid samples. The energy yield from grape marc was maximized at lower treatment temperatures, which also decreased the content of less thermally stable compounds in the attained char. Higher treatment temperatures decreased grape marc solid, carbon and energy yields and led to an increase in thermally labile compounds compared to lower temperatures likely due to the condensation of liquid compounds or volatiles trapped in the pores of char particles. The alkali metal contents of char ash were reduced coupled with an increase in respective phosphorus. Overall the results support the use of hydrothermally treated grape marc in solid fuel applications, if elevated levels of ash phosphorus can be tolerated.

Prediction of biomass ash fusion behaviour by the use of detailed characterization methods coupled with thermodynamic analysis.

OpenAIRE

Rizvi, T.; Pourkashanian, M.; Jones, J.; Darvell, L.; Xing, P.; Nimmo, W.

2014-01-01

Ash deposition such as slagging and fouling on boiler tube surfaces is an inevitable, though undesirable consequence of burning solid fuels in boilers. The role of fuel characteristics, in affecting the form and severity of the problem, is significant. In recent years, biomass fuels have gained increasing popularity as an environmentally friendly source of energy in power plants all over the world. This study is based on characterising the fusion behaviour of four biomass fuels (pine wood, pe...

Reuse of partially sulphated CFBC ash as an SO{sub 2} sorbent

Energy Technology Data Exchange (ETDEWEB)

Wu, Y.; Jia, L.; Anthony, E.J. [Natural Resources Canada, Ottawa, ON (Canada). CANMET Energy; Nobili, M.; Telesca, A. [Basilicata Univ., Potenza (Italy). Dept. of Environmental Engineering and Physics; Montagnaro, F. [Naples Univ., Naples (Italy). Dept. of Chemistry

2010-06-15

Ash produced from circulating fluidized bed combustion (CFBC) boilers typically contains large amounts of unreacted calcium oxide (CaO) when limestone is added into the combustor for in situ removal of sulphur dioxide (SO{sub 2}). This paper reported on a study that evaluated the reactivation of partially sulphated ash obtained from an industrial circulating fluidized bed combustion (CFBC) boiler by hydration with liquid water and steam. A pilot-scale mini-CFBC was used to evaluate the results of reactivation on the bed ash by hydrating with liquid water and admixtures of sodium carbonate (Na{sub 2}CO{sub 3}) in solution or as powder. Re-sulphation tests on the hydrated samples were performed in a Cahn 1000 thermogravimetric analyzer (TGA) at 850 degrees C for 90 minutes in a simulated flue gas environment with sulphur dioxide (SO{sub 2}) concentration at 5000 ppm. Re-sulphation was carried out on unhydrated ash at the same conditions used in the baseline test. The TGA results showed that although liquid water and steam successfully hydrate and reactivate the unreacted CaO in the bed ash, the treated ashes sulphated to widely different extents. Attempts to reactivate fly ash with hydration failed, but the fly ash by itself was extremely reactive. When the treated ash was re-injected into the combustor with the fuel, the effect on SO{sub 2} removal efficiency was negligible if Na{sub 2}CO{sub 3} was added as powder. Doping with aqueous solution improved SO{sub 2} removal, but to a lesser extent than if only water hydration was used. Increasing the amount of water to reactivate the ash did not improve the sulphur capture capacity in the mini-CFBC. It was concluded that reactivation by water is the most practical way to reuse the partially sulphated bed ash as a sulphur sorbent. 21 refs., 7 tabs., 3 figs.

Overview of hydraulic ash and slag transport in the Power Plantt 'Oslomej': Macedonia

Directory of Open Access Journals (Sweden)

Cvetanoski Radomir K.

2017-01-01

Full Text Available AD ELEM Skopje Subsidiary REK 'Oslomej' s. Oslomej is a part of the energy system with an installed power of 125 MW and the net average annual production of 500 GWh of electricity. The basic fuel is coal with an average of 7600 KJ/kg. Coal from the mine is provided Oslomej - west and old mine (Oslomej-east wherein 2009. excavated 1.156.709 t. The main aim of the project is solving environmental problems in Power Plant Oslomej and its surrounding area that creates the existing system of transport and disposal of ash and slag (transport of moist ash by conveyor belt at an open landfill, so the main task of this Project is introducing new technologies of transport and disposal of ash and slag in the form of hydro mixtures.

Micro Fine Sized Palm Oil Fuel Ash Produced Using a Wind Tunnel Production System

Directory of Open Access Journals (Sweden)

R. Ahmadi

2016-01-01

Full Text Available Micro fine sized palm oil fuel ash (POFA is a new supplementary cementitious material that can increase the strength, durability, and workability of concrete. However, production of this material incurs high cost and is not practical for the construction industry. This paper investigates a simple methodology of producing micro fine sized POFA by means of a laboratory scale wind tunnel system. The raw POFA obtained from an oil palm factory is first calcined to remove carbon residue and then grinded in Los Angeles abrasion machine. The grinded POFA is then blown in the fabricated wind tunnel system for separation into different ranges of particle sizes. The physical, morphological, and chemical properties of the micro fine sized POFA were then investigated using Laser Particle Size Analyser (PSA, nitrogen sorption, and Scanning Electron Microscopy with Energy Dispersive X-Ray (SEM-EDX. A total of 32.1% micro fine sized POFA were collected from each sample blown, with the size range of 1–10 micrometers. The devised laboratory scale of wind tunnel production system is successful in producing micro fine sized POFA and, with modifications, this system is envisaged applicable to be used to commercialize micro fine sized POFA production for the construction industry.

Formation of chlorinated organic compounds in fluidized bed combustion of recycled fuels

International Nuclear Information System (INIS)

Vesterinen, R.; Kallio, M.; Kirjalainen, T.; Kolsi, A.; Merta, M.

1997-01-01

Four tests of co-combustion of recycled fuels (REP) with peat and coal in the 15 kW fluidized bed reactor were performed. The recycled fuel was so-called dry fraction in four vessels sampling at Keltinmaeki. In three tests a part of peat energy was replaced with coal. The mixtures were prepared so that in all mixtures 25 % of energy was recycled fuel and 75 % was either peat or the mixture of peat and coal. The concentrations of polyaromatic hydrocarbons (PAH), polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) and chlorophenols decreased with increasing part of coal due to the increasing sulphur/chlorine ratio. Principal Component Analysis (PCA) and Partial Least Square regression analysis (PLS) showed that the chlorine, copper and sulphur contents of the fuel effected most on the concentrations of chlorophenols, chlorobenzenes, PCBs and PCDDs/PCDFs. Other variables influencing on a model were the lead concentration and the sulphur/chlorine ratio in fuel and the hydrogen chloride concentration of the flue gas. The concentrations of chlorophenols and chlorobenzenes were also significant for PCDD/PCDF concentrations in flue gas. The sulphur, chlorine, copper and chromium contents in fly ash and the temperature of the reactor influenced on the chlorophenol, chlorobenzene, PCB and PCDD/PCDF concentrations in fly ash. The chlorophenol and chlorobenzene contents in fly ash, the sulphur/chlorine ratio and the lead content in fuel, the sulphur dioxide, hydrogen chloride and carbon monoxide concentrations in flue gas had also influence on PCDD/PCDF concentrations in fly ash

Operational and environmental hazards of the quality degradation of fuels for power plants

Energy Technology Data Exchange (ETDEWEB)

Szabo, I.

1987-01-01

Higher sulphur and other minerals content in coal increases hazardous emission and, simultaneously, the caloric efficiency of the fuel decreases. The basic production control aspect of coal mines should be to produce coal with lesser ash content and higher calorific value rather than the higher quantity output of mines. For testing purposes, continuous ash content and calorific value monitors and displays should be installed at the power plants before fuel combustion.

Ash particle erosion on steam boiler convective section

Energy Technology Data Exchange (ETDEWEB)

Meuronen, V

1998-12-31

In this study, equations for the calculation of erosion wear caused by ash particles on convective heat exchanger tubes of steam boilers are presented. A new, three-dimensional test arrangement was used in the testing of the erosion wear of convective heat exchanger tubes of steam boilers. When using the sleeve-method, three different tube materials and three tube constructions could be tested. New results were obtained from the analyses. The main mechanisms of erosion wear phenomena and erosion wear as a function of collision conditions and material properties have been studied. Properties of fossil fuels have also been presented. When burning solid fuels, such as pulverized coal and peat in steam boilers, most of the ash is entrained by the flue gas in the furnace. In bubbling and circulating fluidized bed boilers, particle concentration in the flue gas is high because of bed material entrained in the flue gas. Hard particles, such as sharp edged quartz crystals, cause erosion wear when colliding on convective heat exchanger tubes and on the rear wall of the steam boiler. The most important ways to reduce erosion wear in steam boilers is to keep the velocity of the flue gas moderate and prevent channelling of the ash flow in a certain part of the cross section of the flue gas channel, especially near the back wall. One can do this by constructing the boiler with the following components. Screen plates can be used to make the velocity and ash flow distributions more even at the cross-section of the channel. Shield plates and plate type constructions in superheaters can also be used. Erosion testing was conducted with three types of tube constructions: a one tube row, an in- line tube bank with six tube rows, and a staggered tube bark with six tube rows. Three flow velocities and two particle concentrations were used in the tests, which were carried out at room temperature. Three particle materials were used: quartz, coal ash and peat ash particles. Mass loss

Combustion characterization of beneficiated coal-based fuels

Energy Technology Data Exchange (ETDEWEB)

Chow, O.K.; Levasseur, A.A.

1995-11-01

The Pittsburgh Energy Technology Center (PETC) of the U.S. Department of Energy is sponsoring the development of advanced coal-cleaning technologies aimed at expanding the use of the nation`s vast coal reserves in an environmentally and economically acceptable manner. Because of the lack of practical experience with deeply beneficiated coal-based fuels, PETC has contracted Combustion Engineering, Inc. to perform a multi-year project on `Combustion Characterization of Beneficiated Coal-Based Fuels.` The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of Beneficiated Coal-Based Fuels (BCs) influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs.

Ten residual biomass fuels for circulating fluidized-bed gasification

Energy Technology Data Exchange (ETDEWEB)

Drift, A. van der; Doorn, J. van [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Vermeulen, J.W. [NV Afvalzorg, Haarlem (Netherlands)

2001-07-01

In co-operation with a Dutch company (NV Afvalzorg) and the Dutch agency for energy and environment (Novem), ECN has successfully tested 10 different biomass residues in its 500 kW{sub th} circulating fluidized-bed gasification facility. Among the fuels used as demolition wood (both puree and mixed with sewage sludge and paper sludge), verge grass, railroad ties, cacao shells and different woody fuels. Railroad ties turn out to contain very little (heavy) metals. Initially, fuel feeding problems often impeded smooth operation. Contrary to feeding systems, the circulating fluidized-bed gasification process itself seems very flexible concerning the conversion of different kinds of biomass fuels. The fuel moisture content is one of the most important fuel characteristics. More moisture means that more air is needed to maintain the process temperature resulting in better carbon conversion and lower tar emission but also lower product gas heating value and lower cold gas efficiency. So, for a good comparison of the gasification behaviour of different fuels, the moisture content should be similar. However, the moisture content should be defined on an ash-free basis rather than on total mass (the usual way). Some of the ashes produced and retained in the second cyclone were analysed both for elemental composition and leaching behaviour. It turned out that the leaching rate of Mo and Br, elements only present in small concentrations, are preventing the ash to be considered as inert material according to the Dutch legislation for dumping on landfill sites. (Author)

Utilization of coal ash/coal combustion products for mine reclamation

International Nuclear Information System (INIS)

Dolence, R.C.; Giovannitti, E.

1997-01-01

Society's demand for an inexpensive fuel, combined with ignorance of the long term impacts, has left numerous scars on the Pennsylvania landscape. There are over 250,000 acres of abandoned surface mines with dangerous highwalls and water filled pits. About 2,400 miles of streams do not meet water quality standards because of drainage from abandoned mines. There are uncounted households without an adequate water supply due to past mining practices. Mine fires and mine subsidence plague many Pennsylvania communities. The estimated cost to reclaim these past scars is over $15 billion. The beneficial use of coal ash in Pennsylvania for mine reclamation and mine drainage pollution abatement projects increased during the past ten years. The increase is primarily due to procedural and regulatory changes by the Department of Environmental Protection (DEP). Prior to 1986, DEP required a mining permit and a separate waste disposal permit for the use of coal ash in backfilling and reclaiming a surface mine site. In order to eliminate the dual permitting requirements and promote mine reclamation, procedural changes now allow a single permit which authorize both mining and the use of coal ash in reclaiming active and abandoned pits. The actual ash placement, however, must be conducted in accordance with the technical specifications in the solid waste regulations

Hydrolytic stability of heavy metal compounds in fly ash of a heat power plant

International Nuclear Information System (INIS)

Suslova, E.P.; Pertsikov, I.Z.

1991-01-01

Ash and slag from solid fuels are utilized widely in building materials and road surfaces, and in agriculture for soil acidulation. For all these uses it is important to know the amount and form of heavy metal compounds contained in ash and their likely behavior when ash and slag wastes are utilized. Studying the behavior of heavy metals in ash residues at contact with water media is important also because, for most trace elements, the authors lack experimental data that would enable us to predict their behavior after prolonged storage and industrial utilization. The present paper describes a study of lixiviation (at various pH in static conditions) of heavy metals form fly ash obtained by burning Azeisk coal. Homogenized ash selected from electric filter sections 1-4 was used, which has the following composition (%): SiO 2 59.8; Al 2 O 3 ; Fe 23 O 3 7.1; CaO 4.1; MgO 1.3; other 2.8. In a neutral medium, Ni, Cu, Zn, Pb, and Mn lixiviation was slight, amounting to 0.01-0.4%. During coal combustion, these elements apparently form compounds that are slightly soluble in water, although it is also possible that ash retains high adsorptivity for heavy metals. As a result, in these conditions the reverse process of sorption of heavy metals from the solution by fly ash is also possible, which would reduce the heavy metal concentration in the solution

A comparative study of the pore structures and surfaces of hardened cement pastes of potential use in radioactive waste repositories

International Nuclear Information System (INIS)

Rowan, S.M.; Donaldson, L.; White, S.

1988-02-01

Measurements of water vapour adsorption at 20 0 C and mercury intrusion have been used to compare the surfaces and pore structures of hardened cement pastes made from ordinary portland cement (OPC) and the additives blast furnace slag (BFS) and pulverised fuel ash (PFA). The results suggest that each additive, after taking part in the hydration reaction with OPC, produces a paste whose gel pore structure is similar to that derived from OPC alone. The BET adsorption surface area of the cement pastes, in the form of half inch diameter coupons was ca. 55 m 2 g -1 and was not influenced by the presence of the additives. However the pastes containing the additives have a larger and better interconnected meso and macropore structure than OPC which may account for larger diffusion coefficients reported elsewhere for caesium ions passing through concrete containing BFS in comparison with a concrete containing OPC alone. (author)

Fly ash carbon passivation

Science.gov (United States)

La Count, Robert B; Baltrus, John P; Kern, Douglas G

2013-05-14

A thermal method to passivate the carbon and/or other components in fly ash significantly decreases adsorption. The passivated carbon remains in the fly ash. Heating the fly ash to about 500 and 800 degrees C. under inert gas conditions sharply decreases the amount of surfactant adsorbed by the fly ash recovered after thermal treatment despite the fact that the carbon content remains in the fly ash. Using oxygen and inert gas mixtures, the present invention shows that a thermal treatment to about 500 degrees C. also sharply decreases the surfactant adsorption of the recovered fly ash even though most of the carbon remains intact. Also, thermal treatment to about 800 degrees C. under these same oxidative conditions shows a sharp decrease in surfactant adsorption of the recovered fly ash due to the fact that the carbon has been removed. This experiment simulates the various "carbon burnout" methods and is not a claim in this method. The present invention provides a thermal method of deactivating high carbon fly ash toward adsorption of AEAs while retaining the fly ash carbon. The fly ash can be used, for example, as a partial Portland cement replacement in air-entrained concrete, in conductive and other concretes, and for other applications.

Ashes to ashes: Large Fraxinus germplasm collections and their fates

Science.gov (United States)

Kim C. Steiner; Paul. Lupo

2010-01-01

As the emerald ash borer (EAB) threatens the survival of our ash species, measures should be taken to preserve their genetic variability in the event that we discover a way to restore populations destroyed by the beetle. As it happens, large germplasm collections exist for our most important and widely distributed eastern species of the genus, white ash (...

Fusion characterization of biomass ash

Energy Technology Data Exchange (ETDEWEB)

Ma, Teng [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Sino-Danish Center for Education and Research, Beijing, 100190 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Fan, Chuigang; Hao, Lifang [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Li, Songgeng, E-mail: sgli@ipe.ac.cn [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Song, Wenli [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Lin, Weigang [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Department of Chemical and Biochemical Engineering, Technical University of Denmark, 2800 Kgs. Lyngby (Denmark)

2016-08-20

Highlights: • A novel method is proposed to analyze fusion characteristics of biomass ash. • T{sub m} can represent the severe melting temperature of biomass ash. • Compared with AFT, TMA is the better choice to analyze the fusion characteristics of biomass ash. - Abstract: The ash fusion characteristics are important parameters for thermochemical utilization of biomass. In this research, a method for measuring the fusion characteristics of biomass ash by Thermo-mechanical Analyzer, TMA, is described. The typical TMA shrinking ratio curve can be divided into two stages, which are closely related to ash melting behaviors. Several characteristics temperatures based on the TMA curves are used to assess the ash fusion characteristics. A new characteristics temperature, T{sub m}, is proposed to represent the severe melting temperature of biomass ash. The fusion characteristics of six types of biomass ash have been measured by TMA. Compared with standard ash fusibility temperatures (AFT) test, TMA is more suitable for measuring the fusion characteristics of biomass ash. The glassy molten areas of the ash samples are sticky and mainly consist of K-Ca-silicates.

Innovative approach to ash radioactivitiy and health impacts of lignite power plants

Energy Technology Data Exchange (ETDEWEB)

Bosevski, T.; Pop-Jordanova, N. [Macedonian Academy of Sciences and Arts, Skopje (Macedonia)

1998-12-31

In Macedonia nearly 90% of the present electricity production utilizes domestic low-calorie lignite, and this is likely to continue for the next few decades. Local and global environmental impacts of fossil fuel utilization are considered. Some innovative extensions to standard methodologies of environmental risk assessment and management are considered. They involve ash radioactivity and psychosomatic health impacts from lignite power plants. Two extensions are proposed: one comprising complete radioactive chains when determining committed effective dose from lignite ash; the other by including the psychosomatic diseases, such as peptic ulcer and arterial hypertension, due to chronic stress induced by power plants during normal operation. 7 refs., 2 figs., 3 tabs.

Ash chemistry and sintering, verification of the mechanisms

Energy Technology Data Exchange (ETDEWEB)

Hupa, M; Skrifvars, B J; Backman, R; Lauren, T; Uusikartano, T; Malm, H; Stenstroem, P; Vesterkvist, M [Aabo Akademi, Turku (Finland). Combustion Chemistry Research Group

1997-10-01

In this project four sintering mechanisms have been studied, i.e., partial melting with a viscous liquid, partial melting with a non-viscous liquid, chemical reaction sintering and solid state sintering. The work has aimed at improving the understanding of ash sintering mechanisms and quantifying their role in combustion and gasification. The work has been oriented in particular on the understanding of biomass ash behavior. The work has not directly focused on any specific technical application. However, results can also be applied on other fuels such as brown coal, petroleum coke, black liquor and different types of wastes (PDF, RDF, MSW). During 1996 the work has focused on identifying bed agglomeration mechanisms and analysing bed agglomerates in both full scale and lab scale FB reactors, as well as comparing how well the compression strength based sintering test can predict bed agglomeration in an FB furnace. (orig.)

Trace elements in coal ash

Science.gov (United States)

Deonarine, Amrika; Kolker, Allan; Doughten, Michael W.

2015-01-01

Coal ash is a residual waste product primarily produced by coal combustion for electric power generation. Coal ash includes fly ash, bottom ash, and flue-gas desulfurization products (at powerplants equipped with flue-gas desulfurization systems). Fly ash, the most common form of coal ash, is used in a range of products, especially construction materials. A new Environmental Protection Agency ruling upholds designation of coal ash as a non-hazardous waste under Subtitle D of the Resource Conservation and Recovery Act, allowing for the continued beneficial use of coal ash and also designating procedures and requirements for its storage.

Fly ash stabilisation of gravel roads; Flygaska som foerstaerkningslager i grusvaeg

Energy Technology Data Exchange (ETDEWEB)

Macsik, Josef

2006-01-15

Majority of the existing gravel roads have low bearing capacity during spring and autumn, due to thaw and/or rain. Low bearing capacity leads often to bad road conditions. This situation results in higher costs for the lumber industry and the public. Management of gravel roads all the year around would traditionally require excavation of frost susceptible soils and replacement with natural materials. Fly ash (from bio fuels) has good technical properties as bearing layer in road constructions. Fly ash stabilised gravel roads have better function and longer life span with less maintenance than traditional gravel roads. The aim of this project is to show how fly ash stabilisation of gravel roads can increase bearing capacity and what its environmental impact is. The overall aim is to make it easier for entrepreneurs and consulting companies to use fly ash during gravel road renovation and/or constructing new gravel roads. This report targets fly ash producers and road constructors as well as environmental agencies. Two different pilot tests were investigated in this study, Norberg with fly ash from Stora Enso Fors AB, and Boerje (Uppsala) with fly ash from Vattenfall Uppsala AB. Both road sections with related reference section were investigated during a two year period. Only fly ash was used in the bearing layer at Norberg and fly ash gravel was used at Boerje. Bearing capacity was investigated twice, for both locations, November 2003 one month after the road renovation and during thawing, April 2004. Water samples from lysimeters, ground water and surface water were only collected and analysed from Norberg. Experience from the fly ash stabilised road sections show that curing and traffic load can with time compensate for less compaction. The same is noticed at Boerje, although deflection measurements show that there are small differences. Stabilisation of gravel roads increases the roads bearing capacity. Two years after stabilisation 90 timber loads were

Influence of a modification of the petcoke/coal ratio on the leachability of fly ash and slag produced from a large PCC power plant

Energy Technology Data Exchange (ETDEWEB)

Maria Izquierdo; Oriol Font; Natalia Moreno (and others) [CSIC, Barcelona (Spain). Institute of Earth Sciences ' Jaume Almera'

2007-08-01

Co-firing of coal with inexpensive secondary fuels such as petroleum coke is expected to increase in the near future in the EU given that it may provide certain economic and environmental benefits with respect to coal combustion. However, changes in the feed fuel composition of power plants may modify the bulk content and the speciation of a number of elements in fly ash and slag. Consequently, leachability of these byproducts also can be modified. This study is focused on identifying the changes in the environmental quality of co-fired fly ash and slag induced by a modification of the petcoke/coal ratio. Petcoke was found to increase the leachable content of V and Mo and to enhance the mobility of S and As. However, with the exception of these elements, the addition of this secondary fuel did not drastically modify the bulk composition or the overall leachability of the resulting fly ash and slag. 30 refs., 3 figs., 2 tabs.

Mercury release from fly ashes and hydrated fly ash cement pastes

Science.gov (United States)

Du, Wen; Zhang, Chao-yang; Kong, Xiang-ming; Zhuo, Yu-qun; Zhu, Zhen-wu

2018-04-01

The large-scale usage of fly ash in cement and concrete introduces mercury (Hg) into concrete structures and a risk of secondary emission of Hg from the structures during long-term service was evaluated. Three fly ashes were collected from coal-fired power plants and three blend cements were prepared by mixing Ordinary Portland cement (OPC) with the same amount of fly ash. The releasing behaviors of Hg0 from the fly ash and the powdered hydrated cement pastes (HCP) were measured by a self-developed Hg measurement system, where an air-blowing part and Hg collection part were involved. The Hg release of fly ashes at room temperature varied from 25.84 to 39.69 ng/g fly ash during 90-days period of air-blowing experiment. In contrast, the Hg release of the HCPs were in a range of 8.51-18.48 ng/g HCP. It is found that the Hg release ratios of HCPs were almost the same as those of the pure fly ashes, suggesting that the hydration products of the HCP have little immobilization effect on Hg0. Increasing temperature and moisture content markedly promote the Hg release.

Fuel related risks; Braenslerisker

Energy Technology Data Exchange (ETDEWEB)

Englund, Jessica; Sernhed, Kerstin; Nystroem, Olle; Graveus, Frank (Grontmij AB, (Sweden))

2012-02-15

The project, within which this work report was prepared, aimed to complement the Vaermeforsk publication 'Handbook of fuels' on fuel related risks and measures to reduce the risks. The fuels examined in this project where the fuels included in the first version of the handbook from 2005 plus four additional fuels that will be included in the second and next edition of the handbook. Following fuels were included: woodfuels (sawdust, wood chips, powder, briquettes), slash, recycled wood, salix, bark, hardwood, stumps, straw, reed canary grass, hemp, cereal, cereal waste, olive waste, cocoa beans, citrus waste, shea, sludge, forest industrial sludge, manure, Paper Wood Plastic, tyre, leather waste, cardboard rejects, meat and bone meal, liquid animal and vegetable wastes, tall oil pitch, peat, residues from food industry, biomal (including slaughterhouse waste) and lignin. The report includes two main chapters; a general risk chapter and a chapter of fuel specific risks. The first one deals with the general concept of risk, it highlights laws and rules relevant for risk management and it discuss general risks that are related to the different steps of fuel handling, i.e. unloading, storing, processing the fuel, transportation within the facility, combustion and handling of ashes. The information that was used to produce this chapter was gathered through a literature review, site visits, and the project group's experience from risk management. The other main chapter deals with fuel-specific risks and the measures to reduce the risks for the steps of unloading, storing, processing the fuel, internal transportation, combustion and handling of the ashes. Risks and measures were considered for all the biofuels included in the second version in the handbook of fuels. Information about the risks and risk management was gathered through interviews with people working with different kinds of fuels in electricity and heat plants in Sweden. The information from

Fly ash aggregates. Vliegaskunstgrind

Energy Technology Data Exchange (ETDEWEB)

1983-03-01

A study has been carried out into artificial aggregates made from fly ash, 'fly ash aggregates'. Attention has been drawn to the production of fly ash aggregates in the Netherlands as a way to obviate the need of disposal of fly ash. Typical process steps for the manufacturing of fly ash aggregates are the agglomeration and the bonding of fly ash particles. Agglomeration techniques are subdivided into agitation and compaction, bonding methods into sintering, hydrothermal and 'cold' bonding. In sintering no bonding agent is used. The fly ash particles are more or less welded together. Sintering in general is performed at a temperature higher than 900 deg C. In hydrothermal processes lime reacts with fly ash to a crystalline hydrate at temperatures between 100 and 250 deg C at saturated steam pressure. As a lime source not only lime as such, but also portland cement can be used. Cold bonding processes rely on reaction of fly ash with lime or cement at temperatures between 0 and 100 deg C. The pozzolanic properties of fly ash are used. Where cement is applied, this bonding agent itself contributes also to the strength development of the artificial aggregate. Besides the use of lime and cement, several processes are known which make use of lime containing wastes such as spray dry absorption desulfurization residues or fluid bed coal combustion residues. (In Dutch)

Hydration of fly ash cement and microstructure of fly ash cement pastes

Energy Technology Data Exchange (ETDEWEB)

Shiyuan, H.

1981-01-01

The strength development and hydration of fly ash cement and the influence of addition of gypsum on those were studied at normal and elevated temperatures. It was found that an addition of a proper amount of gypsum to fly ash cement could accelerate the pozzolanic reaction between CH and fly ash, and as a result, increase the strength of fly ash cement pastes after 28 days.

Glass-ceramic from mixtures of bottom ash and fly ash.

Science.gov (United States)

Vu, Dinh Hieu; Wang, Kuen-Sheng; Chen, Jung-Hsing; Nam, Bui Xuan; Bac, Bui Hoang

2012-12-01

Along with the gradually increasing yield of the residues, appropriate management and treatment of the residues have become an urgent environmental protection problem. This work investigated the preparation of a glass-ceramic from a mixture of bottom ash and fly ash by petrurgic method. The nucleation and crystallization kinetics of the new glass-ceramic can be obtained by melting the mixture of 80% bottom ash and 20% fly ash at 950 °C, which was then cooled in the furnace for 1h. Major minerals forming in the glass-ceramics mainly are gehlenite (Ca(2)Al(2)SiO(7)) & akermanite (Ca(2)MgSiO(7)) and wollastonite (CaSiO(3)). In addition, regarding chemical/mechanical properties, the chemical resistance showing durability, and the leaching concentration of heavy metals confirmed the possibility of engineering and construction applications of the most superior glass-ceramic product. Finally, petrurgic method of a mixture of bottom ash and fly ash at 950 °C represents a simple, inexpensive, and energy saving method compared with the conventional heat treatment. Copyright © 2012 Elsevier Ltd. All rights reserved.

Reduced ash related operational problems (slagging, bed agglomeration, corrosion and fouling) by co-combustion biomass with peat; Minskade askrelaterade driftsproblem (belaeggning, slaggning, hoegtemperatur-korrosion, baeddagglomerering) genom inblandning av torv i biobraenslen

Energy Technology Data Exchange (ETDEWEB)

Oehman, Marcus; Boman, Christoffer; Erhardsson, Thomas; Gilbe, Ram; Pommer, Linda; Bostroem, Dan; Nordin, Anders; Samuelsson, Robert; Burvall, Jan

2006-12-15

Combustion studies were performed in both a fluidized bed (5 kW) and in an under-feed pellets burner (20 kW) to elucidate the responsible mechanisms for the positive effects on ash related operational problems (i.e. slagging, fouling, corrosion and bed agglomeration) during co-combustion of several problematic biomass with peat. Three typical carex-containing Swedish peat samples with differences in e.g. silicon-, calcium- and sulfur contents were co-fired with logging residues, willow and straw in proportions corresponding to 15-40 weight %d.s. Mixing of corresponding 20 wt-% of peat significantly reduced the bed agglomeration tendencies for all fuels. The fuel specific agglomeration temperature were increased by 150-170 deg C when adding peat to the straw fuel and approximately 70-100 deg C when adding peat to the logging residue- and the willow fuel. The increased level of calcium in the inner bed particle layer caused by the added reactive calcium from the peat and/or removing alkali in the gas phase to a less reactive particular form via sorption and/or reaction with reactive peat ash (containing calcium, silica etc.) during which larger particles (>1{mu}m) are formed where collected potassium is present in a less reactive form, is considered to be the dominated reason for the increased agglomeration temperatures during combustion of logging residues and willow. During straw combustion, the ash forming matter were found as individual ash sticky particles in the bed. The iron, sulphur and calcium content of these individual ash particles were significantly increased when adding peat to the fuel mix thereby decreasing the stickiness of these particles i.e. reducing the agglomeration tendencies. Adding peat to the relatively silicon-poor fuels (willow and logging residues) resulted in higher slagging tendencies, especially when the relative silicon rich peat fuel (Brunnskoelen) was used. However, when co-combusting peat with the relatively silicon and potassium

Fusion characterization of biomass ash

DEFF Research Database (Denmark)

Ma, Teng; Fan, Chuigang; Hao, Lifang

2016-01-01

The ash fusion characteristics are important parameters for thermochemical utilization of biomass. In this research, a method for measuring the fusion characteristics of biomass ash by Thermo-mechanical Analyzer, TMA, is described. The typical TMA shrinking ratio curve can be divided into two...... stages, which are closely related to ash melting behaviors. Several characteristics temperatures based on the TMA curves are used to assess the ash fusion characteristics. A new characteristics temperature, Tm, is proposed to represent the severe melting temperature of biomass ash. The fusion...... characteristics of six types of biomass ash have been measured by TMA. Compared with standard ash fusibility temperatures (AFT) test, TMA is more suitable for measuring the fusion characteristics of biomass ash. The glassy molten areas of the ash samples are sticky and mainly consist of K-Ca-silicates....

Arsenic, chromium and mercury removal using mussel shell ash or a sludge/ashes waste mixture.

Science.gov (United States)

Seco-Reigosa, Natalia; Peña-Rodríguez, Susana; Nóvoa-Muñoz, Juan Carlos; Arias-Estévez, Manuel; Fernández-Sanjurjo, María J; Alvarez-Rodríguez, Esperanza; Núñez-Delgado, Avelino

2013-04-01

Different batches of valued mussel shell and waste mussel shell ash are characterised. Shell ash has pH > 12 and high electrical conductivities (between 16.01 and 27.27 dS m(-1)), while calcined shell shows pH values up to 10.7 and electrical conductivities between 1.19 and 3.55 dS m(-1). X-ray fluorescence, nitric acid digestion and water extractions show higher concentrations in shell ash for most parameters. Calcite is the dominant crystalline compound in this ash (95.6%), followed by aragonite. Adsorption/desorption trials were performed for mussel shell ash and for a waste mixture including shell ash, sewage sludge and wood ash, showing the following percentage adsorptions: Hg(II) >94%, As(V) >96% and Cr(VI) between 11 and 30% for shell ash; Hg(II) >98%, As(V) >88% and Cr(VI) between 30 and 88% for the waste mixture. Hg and As desorption was ash and the waste mixture, while Cr desorption was between 92 and 45% for shell ash, and between 19 and 0% for the mixture. In view of that, mussel shell ash and the mixture including shell ash, sewage sludge and wood ash could be useful for Hg(II) and As(V) removal.

A study on the radioactive waste management for DUPIC fuel cycle

Energy Technology Data Exchange (ETDEWEB)

Chun, Kwan Sik; Park, H. S.; Park, J. J.; Kim, J. H.; Cho, Y. H.; Shin, J. M.; Kim, Y. K.; Kim, J. S.; Kim, J. G.; Park, S. D.; Suh, M. Y.; Sohn, S. C.; Song, B. C.; Lee, C. H.; Jeon, Y. S.; Jo, K. S.; Jee, K. Y.; Jee, C. S.; Han, S. H.

1997-09-01

Part 1: The characteristics if the radioactive wastes coming from the DUPIC fuel manufacturing process were analyzed and evaluated. The gross {alpha}-activity and {alpha}-, {gamma}-spectrum of irradiated zircaloy specimens form KORI unit 1 were analyzed. In order to develop the trapping media of radioactive ruthenium oxides, trapping behavior of volatilized ruthenium oxides on various metal oxides or carbonates was analyzed. Fly ash was selected as a trapping materials for gaseous cesium. And reaction characteristics of CsNO{sub 3} and CsI with fly ash have been investigated. Also, trapping material were performed to test fly ash filter for removal of gaseous cesium under the air and hydrogen atmosphere. The applicability of fly ash to the vitrification of the spent filter was analyzed in the aspects of predictability, leachability. Good quality of Borosilicate glass was formed using Cesium spent filter. Offgas treatment system of DUPIC fuel manufacturing facility was designed and constructed in order to trap of gaseous radioactive waste from 100 batch of OREOXA furnace (the capacity : 500 g/batch). Part II: To develop chemical analysis techniques necessary for understanding chemical properties of the highly radioactive materials related to the development of DUPIC fuel cycle technology, the following basic studies were performed : dissolution of SIMFUEL (simulated fuel), determination of uranium by potentiometry and UV/Vis absorption spectrophotometry, separation of PWR spent fuel, group separation of fission products from uranium, individual separation for analysis of actinides, determination of free acid in a artificial dissolved solution of PWR spent fuel, group separation of fission products form uranium, individual separation of Sm from a mixed rare earth elements and measurement of its isotopes by TI-mass spectrometry, and characteristics of detectors in inductively coupled plasma atomic emission spectrometer (ICP-AES) suitable for analysis of trace fission

A study on the radioactive waste management for DUPIC fuel cycle

International Nuclear Information System (INIS)

Chun, Kwan Sik; Park, H. S.; Park, J. J.; Kim, J. H.; Cho, Y. H.; Shin, J. M.; Kim, Y. K.; Kim, J. S.; Kim, J. G.; Park, S. D.; Suh, M. Y.; Sohn, S. C.; Song, B. C.; Lee, C. H.; Jeon, Y. S.; Jo, K. S.; Jee, K. Y.; Jee, C. S.; Han, S. H.

1997-09-01

Part 1: The characteristics if the radioactive wastes coming from the DUPIC fuel manufacturing process were analyzed and evaluated. The gross α-activity and α-, γ-spectrum of irradiated zircaloy specimens form KORI unit 1 were analyzed. In order to develop the trapping media of radioactive ruthenium oxides, trapping behavior of volatilized ruthenium oxides on various metal oxides or carbonates was analyzed. Fly ash was selected as a trapping materials for gaseous cesium. And reaction characteristics of CsNO 3 and CsI with fly ash have been investigated. Also, trapping material were performed to test fly ash filter for removal of gaseous cesium under the air and hydrogen atmosphere. The applicability of fly ash to the vitrification of the spent filter was analyzed in the aspects of predictability, leachability. Good quality of Borosilicate glass was formed using Cesium spent filter. Offgas treatment system of DUPIC fuel manufacturing facility was designed and constructed in order to trap of gaseous radioactive waste from 100 batch of OREOXA furnace (the capacity : 500 g/batch). Part II: To develop chemical analysis techniques necessary for understanding chemical properties of the highly radioactive materials related to the development of DUPIC fuel cycle technology, the following basic studies were performed : dissolution of SIMFUEL (simulated fuel), determination of uranium by potentiometry and UV/Vis absorption spectrophotometry, separation of PWR spent fuel, group separation of fission products from uranium, individual separation for analysis of actinides, determination of free acid in a artificial dissolved solution of PWR spent fuel, group separation of fission products form uranium, individual separation of Sm from a mixed rare earth elements and measurement of its isotopes by TI-mass spectrometry, and characteristics of detectors in inductively coupled plasma atomic emission spectrometer (ICP-AES) suitable for analysis of trace fission products. (author

Exploring the molecular and biochemical basis of ash resistance to emerald ash borer

Science.gov (United States)

Justin G.A. Whitehill; Daniel A. Herms; Pierluigi. Bonello

2010-01-01

Larvae of the emerald ash borer (EAB) (Agrilus planipennis) feed on phloem of ash (Fraxinus spp.) trees. It is hypothesized that the resistance of Asian species of ash (e.g., Manchurian ash, F. mandshurica) to EAB is due to endogenous defenses present in phloem tissues in the form of defensive proteins and/or...

Properties and Leachability of Self-Compacting Concrete Incorporated with Fly Ash and Bottom Ash

Science.gov (United States)

Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Jamaluddin, Norwati; Bakri Abdullah, Mohd Mustafa Al

2016-06-01

The process of combustion in coal-fired power plant generates ashes, namely fly ash and bottom ash. Besides, coal ash produced from coal combustion contains heavy metals within their compositions. These metals are toxic to the environment as well as to human health. Fortunately, treatment methods are available for these ashes, and the use of fly ash and bottom ash in the concrete mix is one of the few. Therefore, an experimental program was carried out to study the properties and determine the leachability of selfcompacting concrete incorporated with fly ash and bottom ash. For experimental study, self-compacting concrete was produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a replacement for sand with the ratios of 10%, 20%, and 30% respectively. The fresh properties tests conducted were slump flow, t500, sieve segregation and J-ring. Meanwhile for the hardened properties, density, compressive strength and water absorption test were performed. The samples were then crushed to be extracted using Toxicity Characteristic Leaching Procedure and heavy metals content within the samples were identified accordingly using Atomic Absorption Spectrometry. The results demonstrated that both fresh and hardened properties were qualified to categorize as self-compacting concrete. Improvements in compressive strength were observed, and densities for all the samples were identified as a normal weight concrete with ranges between 2000 kg/m3 to 2600 kg/m3. Other than that, it was found that incorporation up to 30% of the ashes was safe as the leached heavy metals concentration did not exceed the regulatory levels, except for arsenic. In conclusion, this study will serve as a reference which suggests that fly ash and bottom ash are widely applicable in concrete technology, and its incorporation in self-compacting concrete constitutes a potential means of adding value to appropriate mix and design.

Ash-forming elements in four Scandinavian wood species part 3: Combustion of five spruce samples

Energy Technology Data Exchange (ETDEWEB)

Werkelin, Johan; Lindberg, Daniel; Skrifvars, Bengt-Johan; Hupa, Mikko [Aabo Akademi Process Chemistry Centre, Piispankatu 8, FI-20500 Turku (Finland); Bostroem, Dan [Energy Technology and Thermal Process Chemistry, Umeaa University, SE-901 87 Umeaa (Sweden)

2011-01-15

Forest residue is the remaining fraction after the outtake of timber, which comprises the tree tops and branches. It may as fuel cause damage to the combustion device through ash slagging and fouling. The objective of this work was to model the ash composition from well-specified samples of a spruce tree: wood, bark, twigs, needles, and shoots. Their ash at 1000 C was modelled using global chemical equilibrium calculations, and laboratory-made ash of the five samples was analyzed by XRD and SEM-EDXA. According to the results, the risk of slagging arises from the spruce foliage: molten alkali silicates from spruce needles and probably molten alkali phosphates from spruce shoots may cause problems in the furnace. Fouling caused by condensing alkali vapours can be produced by all five samples. The amount of alkali vapours in the flue gas was in the same order of magnitude for all five samples, in spite of large differences in their original alkali contents. (author)

TECHNOLOGY AND EFFICIENCY OF PEAT ASH USAGE IN CEMENT CONCRETE

Directory of Open Access Journals (Sweden)

G. D. Liakhevich

2015-01-01

Full Text Available One of the main ways to improve physical and mechanical properties of cement concrete is an introduction of ash obtained due to burning of fossil fuels into concrete mix. The concrete mixes with ash are characterized by high cohesion, less water gain and disintegration. At the same time the concrete has high strength, density, water resistance, resistance to sulfate corrosion. The aim of this paper is to explore the possibility to use peat ash and slag of peat enterprises of the Republic of Belarus in the concrete for improvement of its physical and mechanical properties and characteristics of peat ash, slag, micro-silica, cement, superplasticizing agent. Compositions and technology for preparation of concrete mixes have been developed and concrete samples have been have been fabricated and tested in the paper. It has been shown that the concrete containing ash, slag obtained due to burning of peat in the industrial installations of the Usiazhsky and Lidsky Peat Briquette Plants and also MK-85-grade micro-silica NSPKSAUsF-1-grade superplasticizing agent have concrete tensile strength within 78–134 MPa under axial compression and 53 MPa – for the control composition. This index is 1.5–2.5 times more than for the sample containing no additives.The usage of peat ash, slag together with MK-85-grade micro-silica and NSPKSAUsF-1-grade superplasticizing agent for fabrication of concrete and reinforced bridge and tunnel structures will provide the following advantages: reduction of cross-sectional area of structures while maintaining their bearing capacity due to higher value of tensile strength in case of axial compression; higher density, waterand gas tightness due to low water cement ratio; high resistance to aggressive environment due to lower content of capillary pores that ensures bridge structure longevity; achievement of environmental and social impacts.

Effect of ash components on the ignition and burnout of high ash coals

Energy Technology Data Exchange (ETDEWEB)

Feng, B.; Yan, R.; Zheng, C.G. [Huazhong University of Science and Technology, Wuhan (China). National Laboratory of Coal Combustion

1998-11-01

The effect of the ash components on the ignition and burnout of four Chinese high ash coals were studied by thermogravimetric analysis. To investigate the influence of the ash components, comparative experiments were carried out with original, deashed and impregnated coals. Eleven types of ash components, such as SiO{sub 2}, CaCO{sub 3}, MgO, Na{sub 2}CO{sub 3}, K{sub 2}CO{sub 3}, Al{sub 2}O{sub 3}, TiO{sub 2}, Fe{sub 2}O{sub 3}, FeS{sub 2}, NH{sub 4}Fe(SO{sub 4}){sub 2}{center_dot}12H{sub 2}O and FeSO{sub 4},(NH{sub 4}){center_dot}6H{sub 2}O were used in the present study. It was found that most of the ash components have negative effects. The strong influence of some ash components suggests that the combustion characteristics of high ash coal may be determined by the ash composition. 5 refs., 2 figs., 2 tabs.

Methodical studies of groundwater pollution caused by fly ash deposits from coal-fired power plants

International Nuclear Information System (INIS)

Spuziak-Salzenberg, D.

1990-01-01

The risk potential of fly ash deposits from fossil-fuel power plants was investigated through laboratory elution experiments (single elution, multiple elution, column leaching). The groundwater risk potential in the case of indiscriminate, unsealed dumping is high because of an increased water hardness and due to sulfate, molybdenum, selenium, boron, chromium, barium, strontium and arsenic contamination. Higher barium and strontium concentrations are typical of fly ash deposits. Barium and strontium thus serve as target elements for identification of sites of long-standing pollution. The risks of arsenic leaching are discussed in detail. (orig./LU) [de

Pengaruh Kombinasi Fly Ash dan Bottom Ash sebagai Bahan Substitusi pada Campuran Beton terhadap Sifat Mekanis

OpenAIRE

Yahya, Tengku Tantoni; Kurniawandy, Alex; Djauhari, Zulfikar

2017-01-01

Fly ash and bottom ash were waste that generated from the power plant burning coal process. Fly ash and bottom ash has the potential to be developed as a basic ingredient in concrete composites. This research aimed to obtain the properties of fresh concrete and hard concrete of the combined effect of fly ash and bottom ash as a substitute ingredient in composite concrete. This research has examined the influence of a combination of waste fly ash and bottom ash to the compressive strength of a...

Utilisation aspects of ashes and green liquor dregs from an integrated semichemical pulp and board mill

Energy Technology Data Exchange (ETDEWEB)

Manskinen, K.

2013-09-01

This thesis investigated the properties of bottom and fly ashes originating from a bubbling fluidised bed boiler (120 MW) using two different fuel mixtures (i.e. Fuel mixture A: coal, wood and peat; and B: wood and peat) and of the green liquor dregs originating from the associated semichemical pulp and board mill in relation to the potential utilisation of these residues from various aspects. The total concentrations of As, Cd, Cr, Cu, Ni, Pb, Zn and Hg in the bottom ashes were lower than the maximum allowable concentrations for these elements in forest fertilisers. The total Ca concentrations in bottom ashes A (2.4%; d.w.) and B (3.4%; d.w.) were lower than the legal requirement of 6.0% (d.w.) for ash used as a forest fertiliser. The total Ca concentrations in fly ashes A (6.4%; d.w.) and B (11.0%; d.w.) were higher than the minimum limit value of 6.0% (d.w.), but the concentration of As in fly ashes A (46.9 mg/kg d.w.) and B (41.3 mg/kg; d.w.) exceeded the maximum limit value of 40 mg/kg (d.w.). Only bottom ash B could be used as a forest fertiliser, provided some additional Ca is used. The bottom ashes both fulfilled the Finnish regulations on waste recovery in earth construction. Due to the elevated total concentration of PAH (23 mg/kg; d.w.) and extractable concentrations of Mo (3.9 mg/kg; d.w.) and Se (0.2 mg/kg; d.w.) in fly ash A, this residue cannot be used in covered structures. Due to the elevated concentration of PAH (90 mg/kg; d.w.) in fly ash B, this residue cannot be used in covered and paved structures. However, the utilisation of these residues as an earth construction agent is still possible, but an environmental permit would be required. According to the sequential extraction studies, extractable concentrations of most of the elements in the fly ash A were higher than those in the bottom ash A. The extractability of various elements, both in the bottom and fly ashes A, varied widely. Most of the elements did not occur as readily soluble and

Speciation of Zinc in ash investigated by X-ray absorption spectroscopy; Zinks foerekomstformer i aska studerade med en roentgenabsorptionsspektrometrisk metod

Energy Technology Data Exchange (ETDEWEB)

Steenari, Britt-Marie; Noren, Katarina

2008-06-15

Direct identification of trace metal compounds in solid materials is difficult to achieve due to the detection limits of available analytical methods. Although zinc is the most abundant trace metal in combustion residues, the number of publications dealing with its direct speciation is small. Struis and co-workers have published an investigation where they used Extended X-ray Absorption Fine Structure spectroscopy (EXAFS) measurements to identify zinc compounds in municipal solid waste incineration fly ash. The EXAFS technique has been used more often for speciation of Zn in contaminated soil. EXAFS data for farm soil samples showed that zinc was most commonly sequestered in layer silicates, but soil particles containing zinc sulphide, zinc chromite and zinc phosphate were also found. Generally, published results show that zinc after being mobilised in a soil, has a clear tendency to be sequestered in silicates, as sulphides or, if there is phosphate available, as phosphate. The aim of the work presented in this work was to use the EXAFS method to show how zinc in chemically bound in ash from woody fuels and from municipal solid waste (MSW). The results can be used for evaluations of the possible toxicity of ash and in predictions of the leaching of zinc from ash. The investigation comprised dry ashes from two fluidised bed combustors fired with forestry litter, bark and other wood fuels, moistened and aged wood ashes and dry ashes from three MSW incinerators: one fluidised bed combustor and two stoker fired combustors. The spectroscopic measurements were carried out at the beam line I811 in the Swedish national synchrotron facility Maxlab at Lund University. The results showed that the lowest concentration of Zn in ash for which it is possible to get any information about the nearest neighbour atoms around zinc is about 500 mg Zn per kg dry ash. If the concentration is higher than 1000 mg/ kg it is possible to obtain information, not only about the nearest

Effect of different sizes of palm oil fuel ash (POFA) towards physical properties of modified bitumen

Science.gov (United States)

Raja Zulkefli, R. N. A.; Yaacob, H.; Putra Jaya, R.; Warid, M. N. M.; Hassan, N.; Hainin, M. R.; Idham, M. K.

2018-04-01

In the past decades, numerous numbers of studies have been carried out to find ways enhancing properties of bitumen. Other than using polymer, agricultural waste such as palm oil fuel ash (POFA) is one of the waste products that can be used to modify bitumen. In this study, the physical and rheological properties of POFA modified bitumen were examined based on different grinding hour and different percentage of POFA. The bitumen were mixed with different percentages of POFA (0, 5 and 7%) which passed through 0.075 mm sieve and grinded at different period (1 and 4 hour). The samples were then tested and compared to conventional bitumen. From TEM results, POFA grinded at 1 hour have sizes between 3-7 µm while POFA grinded for 4 hours have finer sizes between 500 nm to 3 µm. The results showed that fineness of POFA affect properties of bitumen significantly. Decreasing in penetration value and decreasing in softening temperature indicates that the modified bitumen becomes harder than conventional bitumen. Modified bitumen gives best results when added with 7% POFA sizes of 500 nm to 3 µm compared to 3 to 7 µm.

Melting and Sintering of Ashes

DEFF Research Database (Denmark)

Hansen, Lone Aslaug

1997-01-01

-1300°C, and a trend of higher fusion temperatures with increasing contents of Al-silicates and quartz was found.c) Fly ashes, bottom ashes and deposits from coal/straw co-firing were all found to consist mainly of metal-alumina and alumina-silicates. These ashes all melt in the temperature range 1000......The thesis contains an experimental study of the fusion and sintering of ashes collected during straw and coal/straw co-firing.A laboratory technique for quantitative determination of ash fusion has been developed based on Simultaneous Thermal Analysis (STA). By means of this method the fraction......, the biggest deviations being found for salt rich (i.e. straw derived) ashes.A simple model assuming proportionality between fly ash fusion and deposit formation was found to be capable of ranking deposition rates for the different straw derived fly ashes, whereas for the fly ashes from coal/straw co-firing...

Investigation on Leaching Behaviour of Fly Ash and Bottom Ash Replacement in Self-Compacting Concrete

Science.gov (United States)

Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Bakri Abdullah, Mohd Mustafa Al

2016-06-01

Fly ash and bottom ash are some of the waste generated by coal-fired power plants, which contains large quantities of toxic and heavy metals. In recent years, many researchers have been interested in studying on the properties of self-compacting concrete incorporated with fly ash and bottom ash but there was very limited research from the combination of fly ash and bottom ash towards the environmental needs. Therefore, this research was focused on investigating the leachability of heavy metals of SCC incorporated with fly ash and bottom ash by using Toxicity Characteristic Leaching Procedure, Synthetic Precipitation Leaching Procedure and Static Leaching Test. The samples obtained from the coal-fired power plant located at Peninsula, Malaysia. In this study, the potential heavy metals leached out from SCC that is produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a substitute for sand with the ratios from 10% to 30% respectively were designated and cast. There are eight heavy metals of concern such as As, Cr, Pb, Zn, Cu, Ni, Mn and Fe. The results indicated that most of the heavy metals leached below the permissible limits from the United States Environmental Protection Agency and World Health Organization limit for drinking water. As a conclusion, the minimum leaching of the heavy metals from the incorporation of fly ash and bottom ash in self-compacting concrete was found in 20% of fly ash and 20% of bottom ash replacement. The results also indicate that this incorporation could minimize the potential of environmental problems.

Characterization of red ceramic pastes incorporated with sugarcane bagasse ash wastes

International Nuclear Information System (INIS)

Faria, K.C.P.; Gurgel, R.F.; Holanda, J.N.F.

2010-01-01

The alcohol industry is one sector that stands out most in the Brazilian agribusiness. Currently there is an increasing demand for sugar and ethanol for use as fuel. The processes of manufacturing these products generate large amounts of waste, the sugarcane bagasse ash waste one of the most abundant. For its chemical and mineralogical characteristics, this waste has aroused the interest of its reuse in the field of red ceramic. This study analyzes the characteristics of a red ceramic paste incorporated with up to 20 wt.% of waste. The following characteristics were performed: chemical composition, X-ray diffraction, particle size, morphology, and Atterberg limits. The results show that the incorporation of sugarcane bagasse ash waste influences the physical-chemical and mineralogical characteristics of red ceramic paste. (author)

Forest industry wood fuel supply

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

The potential for wood fired energy production in the UK is significant. Large scale developments are currently underway which could utilise over 100,000 green tonnes of forest residues. The fuel supply chain is likely to be complicated and there are perceived risks in its organisation and security. This report sets out to address some of these perceived risks and suggest suitable measures to reduce it. Six areas of the fuel supply chain have been studied, namely; Extraction, Comminution, Transport, Assessment and payment of wood fuel; Environmental impact; Nutrient recycling (ash disposal). (author)

Processed bottom ash for replacing fine aggregate in making high-volume fly ash concrete

Directory of Open Access Journals (Sweden)

Antoni

2017-01-01

Full Text Available Bottom ash is a coal plant by-product that is abundant and underutilized. There is the potential use of bottom ash as a fine aggregate replacement in concrete mixtures; however, the problems of water absorption and uniformity of quality of the material need to be overcome first. In this study, bottom ash was treated by sieve separation and pounding to smaller particle size for use as a sand substitute. The physical and chemical characteristics of bottom ash were tested after treatment including water absorption, sieve analysis, and fineness modulus. Highvolume fly ash (HVFA mortar specimens were made and the compressive strength and flowability test using bottom ash after treatment are compared with that of the sand specimen. Low water to cementitious ratio was used to ensure higher strength from the cementitious paste and superplasticizer demand was determined for each treatment. The result showed that bottom ash can be used as fine aggregate replacement material. Sieve separation of the bottom ash could produce 75% of the compressive strength compared with the control sand specimen, whereas pounded bottom ash could have up to 96% of the compressive strength of the control specimen. A 28-day compressive strength of 45 MPa was achievable with 100% replacement of fine aggregate with bottom ash.

Impact of co-combustion of petroleum coke and coal on fly ash quality: Case study of a Western Kentucky power plant

International Nuclear Information System (INIS)

Hower, James C.; Thomas, Gerald A.; Mardon, Sarah M.; Trimble, Alan S.

2005-01-01

Petroleum coke has been used as a supplement or replacement for coal in pulverized-fuel combustion. At a 444-MW western Kentucky power station, the combustion of nearly 60% petroleum coke with moderate- to high-sulfur Illinois Basin coal produces fly ash with nearly 50% uncombusted petroleum coke and large amounts of V and Ni when compared to fly ash from strictly pulverized coal burns. Partitioning of the V and Ni, known from other studies to be concentrated in petroleum coke, was noted. However, the distribution of V and Ni does not directly correspond to the amount of uncombusted petroleum coke in the fly ash. Vanadium and Ni are preferentially associated with the finer, higher surface area fly ash fractions captured at lower flue gas temperatures. The presence of uncombusted petroleum coke in the fly ash doubles the amount of ash to be disposed, makes the fly ash unmarketable because of the high C content, and would lead to higher than typical (compared to other fly ashes in the region) concentrations of V and Ni in the fly ash even if the petroleum coke C could be beneficiated from the fly ash. Further studies of co-combustion ashes are necessary in order to understand their behavior in disposal

Ultrasonic coal-wash for de-ashing and de-sulfurization. Experimental investigation and mechanistic modeling

Energy Technology Data Exchange (ETDEWEB)

Ambedkar, B. [Indian Institute of Technology Madras, Chennai (India). Dept. of Chemical Engineering

2012-07-01

This study focuses on the physical aspects of ultrasonic de-ashing and de-sulfurization, such as cavitation, streaming and their combined effects. Ambedkar Balraj proposes an ultrasound-assisted coal particle breakage mechanism and explores aqueous and solvent-based ultrasonic techniques for de-ashing and de-sulfurization. Ambedkar designs a Taguchi L-27 fractional-factorial matrix to assess the individual effects of key process variables. In this volume he also describes process optimization and scale-up strategies. The author provides a mechanism-based model for ultrasonic reagent-based coal de-sulfurization, proposes a flow diagram for ultrasonic methods of high-throughput coal-wash and discusses the benefits of ultrasonic coal-wash. Coal will continue to be a major fuel source for the foreseeable future and this study helps improve its use by minimising ash and sulfur impurities.

Electrodialytic remediation of fly ash from co-combustion of wood and straw

International Nuclear Information System (INIS)

Chen, Wan; Jensen, Pernille E.; Ottosen, Lisbeth M.; Kirkelund, Gunvor M.

2015-01-01

The heavy metal content in fly ash from biomass combustion, such as straw, wood and sludge, often needs reducing before the ash can be used as fertilizer for agricultural land or as a component in the production of construction materials. In this study, fly ash from a boiler fueled with wood chips and straw was treated either by electrodialytic remediation (EDR) directly or by a combination of EDR and pre-wash with distilled water to investigate the possibilities of reducing the heavy metal content and reusing nutrients as fertilizer and bulk material in construction materials. Different experimental set-ups were tested for EDR treatment primarily of Cd and Pb as well as of Cu and Zn. Elemental contents such as K, P and Ni were compared in ash samples before and after treatment. The results showed that pre-washing caused an increase in total concentrations of most heavy metals because the highly soluble fraction, mainly KCl and K 2 SO 4 , was removed. After EDR treatment, the Cd concentration was reduced to below 2 mg kg −1 in all ash samples with high and stable average removal of above 95%, no matter how high the initial concentration was. The amount of Pb removed varied from 12% to 67%. Even though Pb was extracted from the ash samples, its concentrations in the treated ash samples were elevated due to the ash dissolution, except in the case of pre-washed ash treated in a two-compartment EDR cell, where the mass of Pb removed was the highest with a final concentration of about 100 mg kg −1 . The two-compartment EDR cell probably performed better due to a fast acidification process. In addition, this process was less energy-consuming. However, the fast acidification did in turn affect the leaching property of the treated ash, such as As and Ni, exceeding the limiting concentrations. The EDR/pre-wash-EDR treated ash mainly contained quartz, and the X-ray diffraction (XRD) peaks of K salts had disappeared. This shows that the potassium fertilizer potential was

Feasibility of backfilling mines using cement kiln dust, fly ash, and cement blends

OpenAIRE

Beltagui, Hoda; Sonebi, Mohammed; Maguire, K.; Taylor, Susan

2018-01-01

Cement kiln dust (CKD) is an industrial by-product of the cement manufacturing process, the composition of which can vary widely. Recent years of using alternative fuels have resulted in higher chloride and alkali contents within CKDs; as such, this limits the applications in which CKDs can be utilised. Using a CKD containing a high free lime content of 29.5%, it is shown that this CKD is capable of activating pulverized fuel ash (PFA) due to its high alkalinity, which can be utilised in low ...

Perspective usage estimation of Volga region combustible shale as a power generating fuel alternative

Science.gov (United States)

Korolev, E.; Barieva, E.; Eskin, A.

2018-05-01

A comprehensive study of combustible shale, common within Tatarstan and Ulyanovsk region, is carried out. The rocks physicochemical parameters are found to meet the power generating fuels requirements. The predictive estimate of ash products properties of combustible shale burning is held. Minding furnace process technology it is necessary to know mineral and organic components behavior when combustible shale is burnt. Since the first will determine slagging properties of energy raw materials, the second – its calorific value. In consideration of this the main research methods were X-ray, thermal and X-ray fluorescence analyses. Summing up the obtained results, we can draw to the following conclusions: 1. The combustible shale in Tatarstan and the Ulyanovsk region has predominantly low calorific value (Qb d = 5-9 MJ/kg). In order to enhance its efficiency and to reduce cost it is possible to conduct rocks burning together with some other organic or organic mineral power generating fuels. 2. High ash content (Ad = 60-80%) that causes a high external ballast content in shale implies the appropriateness of using this fuel resource next to its exploitation site. The acceptable distance to a consumer will reduce unproductive transportation charges for large ash and moisture masses. 3. The performed fuel ash components characteristics, as well as the yield and volatiles composition allow us to specify the basic parameters for boiler units, designed for the Volga combustible shale burning. 4. The noncombustible residual components composition shows that shale ash can be used in manufacture of materials of construction.

Increase in efficiency and reduction of generation cost at hard coal-fired power plants. Post-combustion of combustion residues from co-firing of RDF and biomass during dry ash removal

Energy Technology Data Exchange (ETDEWEB)

Baur, Guenter [Magaldi Power GmbH, Esslingen (Germany); Spindeldreher, Olaf [RWE Generation SE, Werne (Germany); RWE Generation SE, Essen (Germany)

2013-09-01

Secondary as well as substitute fuels are being used in hard coal-fired power plants to improve efficiency and to enlarge fuel flexibility. However, grinding and firing systems of the existing coal-fired plants are not designed for those co-fuels. Any deterioration of the combustion performance would reduce the power output and increase ash disposal costs by increased content of combustion residues. The application of air-cooled ash removal, with simultaneous and controlled post-combustion of unburned residues on the conveyor belt, enlarges the furnace and maintains combustion efficiency even with different fuel qualities. Plant efficiency can also be increased through heat recovery. (orig.)

Ash formation and deposition in coal and biomass fired combustion systems: Progress and challenges in the field of ash particle sticking and rebound behavior

DEFF Research Database (Denmark)

Kleinhans, Ulrich; Wieland, Christoph; Frandsen, Flemming J.

2018-01-01

. The impaction of solid, molten or partially molten particles on surfaces is dependent on the particle and surface characteristics. For instance, a particulate deposit might capture incoming particles or be removed due to erosion, while a molten layer will collect all impacting particles, no matter...... if they are sticky or not. The main properties affecting the particle stickiness are the viscosity and surface tension for silicate-rich ashes. On the contrary, the stickiness of salt-rich ashes – typical for herbaceous biomass and wood- or waste-based fuels – is often described using the liquid melt fraction......, their required parameters are discussed and typical particle and surface properties found in combustion systems, are summarized. Eight different sticking criteria are implemented in a computational fluid dynamics code and computations are compared against measurements from an entrained flow reactor. Uniform...

Hot-Gas Filter Ash Characterization Project

Energy Technology Data Exchange (ETDEWEB)

Swanson, M.L.; Hurley, J.P.; Dockter, B.A.; O`Keefe, C.A.

1997-07-01

Large-scale hot-gas filter testing over the past 10 years has revealed numerous cases of cake buildup on filter elements that has been difficult, if not impossible, to remove. At times, the cake can blind or bridge between candle filters, leading to filter failure. Physical factors, including particle-size distribution, particle shape, the aerodynamics of deposition, and system temperature, contribute to the difficulty in removing the cake, but chemical factors such as surface composition and gas-solid reactions also play roles in helping to bond the ash to the filters or to itself. This project is designed to perform the research necessary to determine the fuel-, sorbent-, and operations-related conditions that lead to blinding or bridging of hot-gas particle filters. The objectives of the project are threefold: (1) Determine the mechanisms by which a difficult-to-clean ash is formed and how it bridges hot-gas filters (2) Develop a method to determine the rate of bridging based on analyses of the feed coal and sorbent, filter properties, and system operating conditions and (3) Suggest and test ways to prevent filter bridging.

Ash fusion temperatures and the transformations of coal ash particles to slag

Energy Technology Data Exchange (ETDEWEB)

Gupta, S.K.; Wall, T.F.; Creelman, R.A.; Gupta, R.P. [University of Newcastle, Newcastle, NSW (Australia). CRC for Black Coal Utilisation

1998-07-01

A mechanistic study is detailed in which coal ash is heated with its shrinkage measured continuously up to a temperature of 1600{degree}C. The temperature corresponding to the rapid rate of shrinkage correspond to the formation of eutectics identified on phase diagrams. Samples were therefore heated to these temperatures, cooled rapidly and examined using a scanning electron microscope (SEM) to identify the associated chemical and physical changes. The progressive changes in the range of chemical composition (from SEM), the extent of undissolved ash particles and porosity were then quantified and related to homogenisation, viscosity and ash fusion mechanisms. Alternate ash fusion temperatures based on different levels of shrinkage have also been suggested to characterise the ash deposition tendency of the coals. 13 refs., 9 figs.

Interspecific proteomic comparisons reveal ash phloem genes potentially involved in constitutive resistance to the emerald ash borer.

Science.gov (United States)

Whitehill, Justin G A; Popova-Butler, Alexandra; Green-Church, Kari B; Koch, Jennifer L; Herms, Daniel A; Bonello, Pierluigi

2011-01-01

The emerald ash borer (Agrilus planipennis) is an invasive wood-boring beetle that has killed millions of ash trees since its accidental introduction to North America. All North American ash species (Fraxinus spp.) that emerald ash borer has encountered so far are susceptible, while an Asian species, Manchurian ash (F. mandshurica), which shares an evolutionary history with emerald ash borer, is resistant. Phylogenetic evidence places North American black ash (F. nigra) and Manchurian ash in the same clade and section, yet black ash is highly susceptible to the emerald ash borer. This contrast provides an opportunity to compare the genetic traits of the two species and identify those with a potential role in defense/resistance. We used Difference Gel Electrophoresis (DIGE) to compare the phloem proteomes of resistant Manchurian to susceptible black, green, and white ash. Differentially expressed proteins associated with the resistant Manchurian ash when compared to the susceptible ash species were identified using nano-LC-MS/MS and putative identities assigned. Proteomic differences were strongly associated with the phylogenetic relationships among the four species. Proteins identified in Manchurian ash potentially associated with its resistance to emerald ash borer include a PR-10 protein, an aspartic protease, a phenylcoumaran benzylic ether reductase (PCBER), and a thylakoid-bound ascorbate peroxidase. Discovery of resistance-related proteins in Asian species will inform approaches in which resistance genes can be introgressed into North American ash species. The generation of resistant North American ash genotypes can be used in forest ecosystem restoration and urban plantings following the wake of the emerald ash borer invasion.

The comparative analysis of heat transfer efficiency in the conditions of formation of ash deposits in the boiler furnaces, with taking into account the crystallization of slag during combustion of coal and water-coal fuel

Science.gov (United States)

Salomatov, V. V.; Kuznetsov, G. V.; Syrodoy, S. V.

2017-11-01

The results of the numerical simulation of heat transfer from the combustion products of coal and coal-water fuels (CWF) to the internal environment. The mathematical simulation has been carried out on the sample of the pipe surfaces of the combustion chamber of the boiler unit. The change in the characteristics of heat transfer (change of thermochemical characteristics) in the conditions of formation of the ash deposits have been taken into account. According to the results of the numerical simulation, the comparative analysis of the efficiency of heat transfer has been carried out from the furnace environment to the inside pipe coolant (water, air, or water vapor) from the combustion of coal and coal-water fuels. It has been established that, in the initial period of the boiler unit operation during coal fuel combustion the efficiency of heat transfer from the combustion products of the internal environment is higher than when using CWF. The efficiency of heat transfer in CWF combustion conditions is more at large times (τ≥1.5 hours) of the boiler unit. A significant decrease in heat flux from the combustion products to the inside pipe coolant in the case of coal combustion compared to CWF has been found. It has been proved that this is due primarily to the fact that massive and strong ash deposits are formed during coal combustion.

Environmental impact assessment of wood ash utilization in forest road construction and maintenance--A field study.

Science.gov (United States)

Oburger, Eva; Jäger, Anna; Pasch, Alexander; Dellantonio, Alex; Stampfer, Karl; Wenzel, Walter W

2016-02-15

The ever increasing use of wood material as fuel for green energy production requires innovative, environmentally safe strategies for recycling of the remaining wood ash. Utilizing wood ash in forest road construction and maintenance to improve mechanical stability has been suggested as a feasible recycling option. To investigate the environmental impact of wood ash application in forest road maintenance, a two-year field experiment was conducted at two Austrian forest sites (Kobernausserwald (KO) (soil pH 5.5) and Weyregg (WE) (pH 7.7)) differing in their soil chemical properties. Two different ashes, one produced by grate incineration (GA) and the other by fluidized bed incineration in a mixture with 15 vol% burnt lime (FBA), were incorporated in repeated road sections at a 15:85% (V/V) ash-to-soil rate. Leaching waters from the road body were collected and analyzed for 32 environmentally relevant parameters over two years. Upon termination of the experiment, sub-road soil samples were collected and analyzed for ash-related changes in soil chemistry. Even though a larger number of parameters was affected by the ash application at the alkaline site (WE), we observed the most pronounced initial increases of pH as well as Al, As, Fe, Mn, Ni, Co, Cu, Mo, and NO2(−) concentrations in leachates beneath GA-treated road bodies at Kobernausserwald due to the lower soil buffer capacity at this site. Despite the observed effects our results indicate that, when specific requirements are met (i.e. appropriate ash quality, sufficient soil buffer capacity below the road body, and single time-point ash incorporation within several decades), wood ash application in forest road construction is generally environmentally acceptable.

EOSLT Consortium Biomass Co-firing. WP 4. Biomass co-firing in oxy-fuel combustion. Part 1. Lab- Scale Experiments

Energy Technology Data Exchange (ETDEWEB)

Fryda, L.E. [ECN Biomass, Coal and Environmental Research, Petten (Netherlands)

2011-07-15

In the frame of WP4 of the EOS LT Co-firing program, the ash formation and deposition of selected coal/biomass blends under oxyfuel and air conditions were studied experimentally in the ECN lab scale coal combustor (LCS). The fuels used were Russian coal, South African coal and Greek Lignite, either combusted separately or in blends with cocoa and olive residue. The first trial period included tests with the Russian and South African coals and their blends with cocoa, the second trial period included Lignite with olive residue tests and a final period firing only Lignite and Russian coal, mainly to check and verify the observed results. During the testing, also enriched air combustion was applied, in order to establish conclusions whether a systematic trend on ash formation and deposition exists, ranging from conventional air, to enriched air (improving post combustion applications) until oxyfuel conditions. A horizontal deposition probe equipped with thermocouples and heat transfer sensors for on line data acquisition, and a cascade impactor (staged filter) to obtain size distributed ash samples including the submicron range at the reactor exit were used. The deposition ratio and the deposition propensity measured for the various experimental conditions were higher in all oxyfuel cases. No significant variations in the ash formation mechanisms and the ash composition were established. Finally the data obtained from the tests performed under air and oxy-fuel conditions were utilised for chemical equilibrium calculations in order to facilitate the interpretation of the measured data; the results indicate that temperature dependence and fuels/blends ash composition are the major factors affecting gaseous compound and ash composition rather than the combustion environment, which seems to affect neither the ash and fine ash (submicron) formation, nor the ash composition. The ash deposition mechanisms were studied in more detail in Part II of this report.

The Effect of an Ultrasound Radiation on the Synthesis of 4A Zeolite from Fly Ash

Science.gov (United States)

Susanto, H.; Imani, N. A. C.; Aslamiyah, N. R.; Istirokhatun, T.; Robbani, M. H.

2018-05-01

The use of coal as a fuel source generates a lot of solid waste fly ash. Thus, efforts to reduce or utilize the amount of fly ash are urgently needed. This paper presents zeolite synthesis from fly ash. The fly ash was activated by using NaOH solution prior to fusing process with a weight ratio of 1:2 and mixing with distilled water at a weight ratio of 1:5. Thereafter, the addition of alumina with a concentration of 0.71 %, 1.42 %, 2.12 %, and 2.8 % w/v was performed. The effects of heating and ultrasound radiation on the characteristic of zeolite products were investigated. The results showed that the addition of alumina 2.8 % w/v resulted in the Si/Al ratio of zeolite 4A is ∼1. SEM images demonstrated that the presence of ultrasound wave resulted in crystals structure morphology as also supported by XRD characterization. The average crystal size for the ultrasonic treatment was 42.46 nm.

Major and trace elements in coal bottom ash at different oxy coal combustion conditions

CSIR Research Space (South Africa)

Oboirien, BO

2014-09-01

Full Text Available This paper presents a detailed study on the effect of temperature on the concentration of 27 major and trace elements in bottom ash generated from oxy fuel-combustion. The major elements are Na, Mg, Al, K, Ca and Fe and the minor and trace elements...

The use of fly-ash particles for dating lake sediments

Energy Technology Data Exchange (ETDEWEB)

Rose, N L [Environmental Change Research Centre, University College London, London (United Kingdom)

1998-08-01

Fly-ash particles comprise two particle types, spheroidal carbonaceous particles (SCP) and inorganic ash spheres (IAS). In lake sediments, these particles form an unambiguous record of atmospheric deposition of industrial pollutants. The main temporal trends of these sediment records have been found to be remarkably consistent over wide geographical areas and these features can be used to ascribe dates to cores undated by other means. SCP are the main particle type used in this way as they are easier to extract and enumerate. IAS are morphologically similar to some natural particles (volcanic, meteoritic) and therefore show a natural background concentration at all pre-industrial sediment depths. Apart from this background temporal trends are similar to SCP and IAS could be used for dating in the same way. Gaining an indication of fuel-type change, either from IAS:SCP ratio or chemical characterization of SCP enables additional dates to be added to sediment cores through comparison with documentary evidence. In the future, as {sup 210}Pb becomes progressively unable to date the post-industrial sediment record, dating using fly-ash techniques may become increasingly important. (orig.) 17 refs.

The use of fly-ash particles for dating lake sediments

International Nuclear Information System (INIS)

Rose, N.L.

1998-01-01

Fly-ash particles comprise two particle types, spheroidal carbonaceous particles (SCP) and inorganic ash spheres (IAS). In lake sediments, these particles form an unambiguous record of atmospheric deposition of industrial pollutants. The main temporal trends of these sediment records have been found to be remarkably consistent over wide geographical areas and these features can be used to ascribe dates to cores undated by other means. SCP are the main particle type used in this way as they are easier to extract and enumerate. IAS are morphologically similar to some natural particles (volcanic, meteoritic) and therefore show a natural background concentration at all pre-industrial sediment depths. Apart from this background temporal trends are similar to SCP and IAS could be used for dating in the same way. Gaining an indication of fuel-type change, either from IAS:SCP ratio or chemical characterization of SCP enables additional dates to be added to sediment cores through comparison with documentary evidence. In the future, as 210 Pb becomes progressively unable to date the post-industrial sediment record, dating using fly-ash techniques may become increasingly important. (orig.)

Particle size distribution of fly ash from co-incineration of bituminous coal with municipal solid waste

Directory of Open Access Journals (Sweden)

Cieślik Ewelina

2018-01-01

Full Text Available One of the source of air pollutants is emission from local coal-fired boiler-houses and domestic heating boilers. The consequence of incineration of municipal waste is the introduction of additional pollutants into the atmosphere, including fly ash. The aim of this work was to evaluate the particle size distribution of fly ash emitted by coal combustion and co-incineration of coal with municipal waste in a domestic 18 kW central heating boiler equipped with an automatic fuel feeder. Mixtures of bituminous coal with different types of solid waste (5, 10 and 15% of mass fraction were used. Solid waste types consisted of: printed, colored PE caps, fragmented cable trunking, fragmented car gaskets and shredded tires from trucks. During the incineration of a given mixture of municipal waste with bituminous coal, the velocity of exhaust gas was specified, the concentration and mass flow of fly ash were determined together with the physico-chemical parameters of the exhaust gas, the samples of emitted fly ash were taken as the test material. Particle size analysis of fly ash was performed using laser particle sizer Fritch Analysette 22. The PM10 share from all fly ashes from incineration of mixtures was about 100%. Differences were noted between PM2.5 and PM1.

Particle size distribution of fly ash from co-incineration of bituminous coal with municipal solid waste

Science.gov (United States)

Cieślik, Ewelina; Konieczny, Tomasz; Bobik, Bartłomiej

2018-01-01

One of the source of air pollutants is emission from local coal-fired boiler-houses and domestic heating boilers. The consequence of incineration of municipal waste is the introduction of additional pollutants into the atmosphere, including fly ash. The aim of this work was to evaluate the particle size distribution of fly ash emitted by coal combustion and co-incineration of coal with municipal waste in a domestic 18 kW central heating boiler equipped with an automatic fuel feeder. Mixtures of bituminous coal with different types of solid waste (5, 10 and 15% of mass fraction) were used. Solid waste types consisted of: printed, colored PE caps, fragmented cable trunking, fragmented car gaskets and shredded tires from trucks. During the incineration of a given mixture of municipal waste with bituminous coal, the velocity of exhaust gas was specified, the concentration and mass flow of fly ash were determined together with the physico-chemical parameters of the exhaust gas, the samples of emitted fly ash were taken as the test material. Particle size analysis of fly ash was performed using laser particle sizer Fritch Analysette 22. The PM10 share from all fly ashes from incineration of mixtures was about 100%. Differences were noted between PM2.5 and PM1.

Survey for tolerance to emerald ash borer within North American ash species

Science.gov (United States)

Jennifer L. Koch; Mary E. Mason; David W. Carey; Kathleen Knight; Therese Poland; Daniel A. Herms

2010-01-01

Since the discovery of the emerald ash borer (EAB) near Detroit, MI, in 2002, more than 40 million ash trees have been killed and another 7.5 billion are at risk in the United States. When the EAB outbreak was initially discovered, our native ash species appeared to have no resistance to the pest.

Cast-concrete products made with FBC ash and wet-collected coal-ash

Energy Technology Data Exchange (ETDEWEB)

Naik, T.R.; Kraus, R.N.; Chun, Y.M.; Botha, F.D. [University of Wisconsin, Milwaukee, WI (United States)

2005-12-01

Cast-concrete hollow blocks, solid blocks, and paving stones were produced at a manufacturing plant by replacing up to 45% (by mass) of portland cement with fluidized bed combustion (FBC) coal ash and up to 9% of natural aggregates with wet-collected, low-lime, coarse coal-ash (WA). Cast-concrete product specimens of all three types exceeded the compressive strength requirements of ASTM from early ages, with the exception of one paving-stone mixture, which fell short of the requirement by less than 10%. The cast-concrete products made by replacing up to 40% of cement with FBC ash were equivalent in strength (89-113% of control) to the products without ash. The abrasion resistance of paving stones was equivalent for up to 34% FBC ash content. Partial replacement of aggregates with WA decreased strength of the products. The resistance of hollow blocks and paving stones to freezing and thawing decreased appreciably with increasing ash contents. The cast-concrete products could be used indoors in regions where freezing and thawing is a concern, and outdoors in a moderate climate.

Fuel pellets from lodge pole pine first thinnings

Energy Technology Data Exchange (ETDEWEB)

Hoegqvist, Olof; Larsson, Sylvia H.; Samuelsson, Robert; Lestander, Torbjoern A. [Swedish Univ. of Agricultural Sciences, Unit of Biomass Technology and Chemistry, Umeaa (Sweden)], e-mail: sylvia.larsson@slu.se

2012-11-01

Stemwood and whole trees of lodgepole pine (Pinus contorta Dougl. var. latifolia L.) were evaluated as raw materials for fuel pellets in a pilot scale pelletizing study. Pellet and pelletizing properties were measured and modeled in an experimental design where raw material moisture content (%), die channel length (mm), and storage time (days) were varied. Additionally, ash contents (%), extractive contents (%), and ash melting temperatures (deg C) were analyzed. For both assortments, raw material moisture content was positively correlated to pellet bulk density and durability (range 9-13%, wet base). Both assortments had ash contents below 0.7%, and thus, fulfilled the demands for class A1 pellets.

Can ash clog soil pores?

Science.gov (United States)

Stoof, Cathelijne; Stoof, Cathelijne; Gevaert, Anouk; Gevaert, Anouk; Baver, Christine; Baver, Christine; Hassanpour, Bahareh; Hassanpour, Bahareh; Morales, Veronica; Morales, Veronica; Zhang, Wei; Zhang, Wei; Martin, Deborah; Martin, Deborah; Steenhuis, Tammo; Steenhuis, Tammo

2015-04-01

Wildfire can greatly increase a landscape's vulnerability to flooding and erosion events, and ash is thought to play a large role in controlling runoff and erosion processes after wildfire. Although ash can store rainfall and thereby reduce runoff and erosion for a limited period after wildfires, it has also been hypothesized to clog soil pores and reduce infiltration. Several researchers have attributed the commonly observed increase in runoff and erosion after fire to the potential pore-clogging effect of ash. Evidence is however incomplete, as to date, research has solely focused on identifying the presence of ash in the soil, with the actual flow processes associated with the infiltration and pore-clogging of ash remaining a major unknown. In several laboratory experiments, we tested the hypothesis that ash causes pore clogging to the point that infiltration is hampered and ponding occurs. We first visualized and quantified pore-scale infiltration of water and ash in sand of a range of textures and at various infiltration rates, using a digital bright field microscope capturing both photo and video. While these visualization experiments confirm field and lab observation of ash washing into soil pores, we did not observe any clogging of pores, and have not been able to create conditions for which this does occur. Additional electrochemical analysis and measurement of saturated hydraulic conductivity indicate that pore clogging by ash is not plausible. Electrochemical analysis showed that ash and sand are both negatively charged, showing that attachment of ash to sand and any resulting clogging is unlikely. Ash also had quite high saturated conductivity, and systems where ash was mixed in or lying on top of sand had similarly high hydraulic conductivity. Based on these various experiments, we cannot confirm the hypothesis that pore clogging by ash contributes to the frequently observed increase in post-fire runoff, at least for the medium to coarse sands

Ferrospheres from fly ashes of Chelyabinsk coals: chemical composition, morphology and formation conditions

Energy Technology Data Exchange (ETDEWEB)

Sokol, E.V.; Kalugin, V.M.; Nigmatulina, E.N.; Volkova, N.I.; Frenkel, A.E.; Maksimova, N.V. [Geophysics and Mineralogy Sb RAS, Novosibirsk (Russian Federation). United Institute of Geology

2002-05-01

Ferrospheres originating during the pulverised fuel firing of brown coals from the Chelyabinsk basin (South Urals, Russia) have been examined for determination of their chemical and phase compositions, morphology and formation conditions. Most of the ferrospheres are close to ideal spheres with dendritic or skeletal structure. The appearance of microsphere inner anatomy is determined by morphology of ferrispinel aggregates, which compose more than 85 vol% of these globules. The analysed ferrispinels are complex solid solutions based on FeFe{sub 2}O{sub 4} with impurities of MgFe{sub 2}O{sub 4}, MnFe{sub 2}O{sub 4} and nCaO x mFe{sub 2}O{sub 3}. The glasses coexisted with ferrispinel crystallites are basic-ultrabasic in composition. Ferrospheres are the quenching products of high-ferrous melts originated from melting of iron-bearing carbonate admixtures in coals. The mass crystallisation of ferrispinels in ferrospheres was a result of iron changes from Fe{sup 2+} to Fe{sup 3+} and following ferritisation of high-ferrous melts during molten drops cooling. The residual melt is quenched to form a low-silicon, high-calcium, high-ferrous glass. the skeletal and dendritic forms of ferrispinel are due to their crystallisation under drastic supercooling conditions. 22 refs., 6 figs., 2 tabs.

Long term effects of ash fertilization of reed canary grass; Laangtidseffekter av askgoedsling vid roerflensodling

Energy Technology Data Exchange (ETDEWEB)

Palmborg, Cecilia; Lindvall, Eva

2011-03-15

Reed canary grass (RCG) is a bio-energy crop with large potential. It is a 1.5 . 2.5 m tall grass that is harvested in spring when it is grown as a fuel. At spring harvest it yields 3 . 10 ton field dried material per ha and year. One disadvantage when reed canary grass is used as a fuel is the high ash content, 5-10 %. This means that large quantities of ash have to be deposited which is expensive, about 1000 SEK/ton. However, since reed canary grass ash contains reasonable amounts of plant nutrients like phosphorous (P), potassium (K) and magnesium (Mg) it could be recycled as fertilizer in agriculture. The ash can be used without any pretreatment since, in agriculture, plant availability is desirable. The aim of this project, was to evaluate a field experiment, where ash was used as a fertilizer in reed canary grass. The experiment was established at the SLU research station in Umea, Sweden in the spring 2002. Three different fertilizer treatments were applied: Treatment A was fertilized with an ash produced by combustion of RCG together with municipal wastes (paper, plastic, leather), treatment B, an ash from combustion of RCG, and for treatment C commercial fertilizers were used. In total, 100 kg ha-1 of nitrogen (N), 15 kg ha-1 of phosphorous (P) and 80 kg ha-1 of potassium (K), were applied each year in all treatments. The amount of ash in treatment A and B was calculated from the chemical analysis of the ashes to be equal to the required amount of P, while K and N were supplied also by commercial fertilizers. [Table 1. Composition of the ashes] Literature study: There is a lack of knowledge about fertilization with reed canary grass ash, since few experiments have been conducted. The composition of reed canary grass is dependent of harvest date and the soil substrate. The amount of ash and the amount of harmful substances such as potassium and chloride generally decreases over winter, giving an increased fuel quality from spring harvest compared to autumn

Ash study for biogas purification

International Nuclear Information System (INIS)

Juarez V, R. I.

2016-01-01

This work evaluates the ashes generated from the wood and coal combustion process of the thermoelectric plant in Petacalco, Guerrero (Mexico) in order to determine its viability as a filter in the biogas purification process. The ash is constituted by particles of morphology and different chemical properties, so it required a characterization of the same by different analytical techniques: as was scanning electron microscopy and X-ray diffraction, in order to observe the microstructure and determine the elemental chemical composition of the particles. Prior to the analysis, a set of sieves was selected to classify as a function of particle size. Four different types of ashes were evaluated: one generated by the wood combustion (wood ash) and three more of the Petacalco thermoelectric generated by the coal combustion (wet fly ash, dry fly ash and dry bottom ash). (Author)

Lunar ash flows - Isothermal approximation.

Science.gov (United States)

Pai, S. I.; Hsieh, T.; O'Keefe, J. A.

1972-01-01

Suggestion of the ash flow mechanism as one of the major processes required to account for some features of lunar soil. First the observational background and the gardening hypothesis are reviewed, and the shortcomings of the gardening hypothesis are shown. Then a general description of the lunar ash flow is given, and a simple mathematical model of the isothermal lunar ash flow is worked out with numerical examples to show the differences between the lunar and the terrestrial ash flow. The important parameters of the ash flow process are isolated and analyzed. It appears that the lunar surface layer in the maria is not a residual mantle rock (regolith) but a series of ash flows due, at least in part, to great meteorite impacts. The possibility of a volcanic contribution is not excluded. Some further analytic research on lunar ash flows is recommended.

Electrodialytic removal of heavy metals from different fly ashes. Influence of heavy metal speciation in the ashes

DEFF Research Database (Denmark)

Pedersen, Anne Juul; Ottosen, Lisbeth M.; Villumsen, Arne

2003-01-01

Electrodialytic Remediation has recently been suggested as a potential method for removal of heavy metals from fly ashes. In this work electrodialytic remediation of three different fly ashes, i.e. two municipal solid waste incinerator (MSWI) fly ashes and one wood combustion fly ash was studied...... in lab scale, and the results were discussed in relation to the expected heavy metal speciation in the ashes. In initial leaching experiments the pH-dependent desorption characteristics of the heavy metals Cd, Pb, Zn and Cu were analogous in the two MSWI ashes, and thus it was expected......-moval efficiencies were observed, especially for Pb and Zn. Cd, the sole heavy metal of environmental concern in the wood ash, was found more tightly bonded in this ash than in the two MSWI ashes. It was suggested that complex Cd-silicates are likely phases in the wood ash whereas more soluble, condensed phases...

Fly ash classification efficiency of electrostatic precipitators in fluidized bed combustion of peat, wood, and forest residues.

Science.gov (United States)

Ohenoja, Katja; Körkkö, Mika; Wigren, Valter; Österbacka, Jan; Illikainen, Mirja

2018-01-15

The increasing use of biomasses in the production of electricity and heat results in an increased amount of burning residue, fly ash which disposal is becoming more and more restricted and expensive. Therefore, there is a great interest in utilizing fly ashes instead of just disposing of it. This study aimed to establish whether the utilization of fly ash from the fluidized bed combustion of peat, wood, and forest residues can be improved by electrostatic precipitator separation of sulfate, chloride, and some detrimental metals. Classification selectivity calculations of electrostatic precipitators for three different fuel mixtures from two different power plants were performed by using Nelson's and Karnis's selectivity indices. Results showed that all fly ashes behaved similarly in the electrostatic separation process SiO 2 resulted in coarse fractions with Nelson's selectivity of 0.2 or more, while sulfate, chloride, and the studied detrimental metals (arsenic, cadmium, and lead) enriched into fine fractions with varying selectivity from 0.2 to 0.65. Overall, the results of this study suggest that it is possible to improve the utilization potential of fly ashes from fluidized bed combustion in concrete, fertilizer, and earth construction applications by using electrostatic precipitators for the fractionating of fly ashes in addition to their initial function of collecting fly ash particles from flue gases. The separation of the finer fractions (ESP 2 and 3) from ESP 1 field fly ash is recommended. Copyright © 2017 Elsevier Ltd. All rights reserved.

Combustion experiments in a small furnace using natural biogenic solid fuels. Emissions and ash quality. Final report; Verbrennungsversuche mit naturbelassenen biogenen Festbrennstoffen in einer Kleinfeuerungsanlage. Emissionen und Aschequalitaet. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Launhardt, T.; Hartmann, H.; Link, H.; Schmid, V.

2000-09-01

Emissions and ash qualities of the fuels were compared in order to assess their pollutant emissions CO, dust, C{sub n}H{sub m}, NO{sub x}, particle size distribution of airborne dust, organic and inorganic chlorinated pollutants (including PCDD/F), PAH and heavy metals. Quality characteristics of the fuels and ashes were investigated as well (nutrient and pollutant concentrations including heavy metals, chlorine, PCDD/F, PAH). The focus was on agricultural biomass, which was compared with chopped pinewood. [German] Ziel des Messvorhabens ist eine umfassende Analyse der Emissionen und der Aschenqualitaet beim Einsatz verschiedener biogener Festbrennstoffe in einer Kleinfeuerungsanlage (50 kW{sub th}). Dadurch soll eine vergleichende Bewertung der unterschiedlichen Brennstoffarten und Aufbereitungsformen (Pellet, Haeckselgut) moeglich werden und eine generelle Aussage ueber das Niveau des Schadstoffausstosses inklusive hochtoxischer organischer Komponenten abgeleitet werden. Ergaenzend dazu soll eine Quantifizierung moeglicher Einfluesse durch den Wassergehalt im Brennstoff und die Heizlast der Feuerungsanlage vorgenommen werden. Zielgroessen der Untersuchung sind der Wirkungsgrad der Feuerungsanlage, die Standard-Emissionsgroessen CO, Staub, C{sub n}H{sub m} und NO{sub x}, die Partikelgroessenverteilung des Flugstaubes, organisch und anorganisch chlorierte Schadstoffe (u.a. PCDD/F), PAK und Schwermetalle. Zusaetzlich werden eine Reihe von Qualitaetsmerkmalen im Brennstoff und in den Aschen betrachtet (Naehr- und Schadstoffgehalte, einschliesslich Schwermetalle, Chlor, PCDD/F, PAK). Im Vordergrund stehen die Biomassebrennstoffe, die speziell in der Landwirtschaft erzeugt werden. Sie werden mit dem Referenzbrennstoff Fichtenhackgut verglichen. (orig.)

Soil and fertilizer amendments and edge effects on the floral succession of pulverized fuel ash

Energy Technology Data Exchange (ETDEWEB)

Shaw, P. [Roehampton University, London (United Kingdom). Whitelands College

2009-01-15

Plots of fresh pulverized fuel ash (PFA, an industrial waste) were inoculated with soils from existing PFA sites and fertilizers in a factorial design, then left unmanaged for 12 years during which time the floral development and soil chemistry were monitored annually. For the first 3 years, the site supported a sparse mix of chenopods (including the scarce Chenopodium glaucum) and halophytes. As salinity declined, ruderals, legumes, and grasses plus the fire-site moss Funaria hygrometrica colonized, followed by Festuca arundinacea grassland (NVC community MG12) and Hippophae rhamnoides scrub. Dactylorhiza incarnata (orchidacea) appeared after 7 years, but only in plots that had received soil from existing orchid colonies. Four years later, a larger second generation of Dactylorhiza appeared, but only in the central zone of the site where vegetation was thinnest. By year 12, the site was dominated by coarse grasses and scrub, with early successional species persisting only in the sparsely vegetated center, where nitrate levels were lowest. This edge effect is interpreted as centripetal encroachment, a process of potentially wider concern for the conservation of low-fertility habitat patches. Overall, seed bank inoculation seems to have introduced few but desirable species (D. incarnata, Pyrola rotundifolia, some halophytes, and annuals), whereas initial application of organic fertilizer had long-lasting ({ge} 10 years) effects on cover and soil composition.

Differential behaviour of combustion and gasification fly ash from Puertollano Power Plants (Spain) for the synthesis of zeolites and silica extraction

International Nuclear Information System (INIS)

Font, O.; Moreno, N.; Diez, S.; Querol, X.; Lopez-Soler, A.; Coca, P.; Garcia Pena, F.

2009-01-01

Coal gasification (IGCC) and pulverised coal combustion (PCC) fly ashes (FAs), obtained from two power plants fed with the carboniferous bituminous coal from Puertollano (Spain), were characterised and used as raw materials for zeolite synthesis by direct conversion (DC) and by alkaline fusion (Fu), and SiO 2 extraction (Si-Ex) at laboratory scale. The Puertollano FAs are characterised by a high SiO 2 content (59%) with respect to EU coal FAs. High zeolite synthesis yields were obtained from both FAs by using conventional alkaline activation. However, the Si extraction yields were very different. The results of the zeolite synthesis from the Si-bearing extracts from both FAs demonstrated that high purity zeolites with high cation exchange capacity (CEC, between 4.3 and 5.3 meq/g) can be produced. The solid residue arising from Si-Ex is also a relatively high NaP1 zeolite product (CEC 2.4-2.7 meq/g) equivalent to the DC products. The zeolitic materials synthesised from both FAs by Fu showed an intermediate (between the high purity zeolites and the DC products) zeolite content with CEC values from 3.4 to 3.7 meq/g. Low leachable metal contents were obtained from high purity A and X zeolites and zeolite material synthesised by Fu for PCC FA.

Palm Oil Fuel Ash (POFA and Eggshell Powder (ESP as Partial Replacement for Cement in Concrete

Directory of Open Access Journals (Sweden)

Mohamad Mazizah Ezdiani

2018-01-01

Full Text Available This study is an attempt to partially replace Ordinary Portland cement (OPC in concrete with palm oil fuel ash (POFA and eggshell powder (ESP. The mix proportions of POFA and ESP were varied at 10% of cement replacement and compared with OPC concrete as control specimen. The fineness of POFA is characterized by passing through 300 μm sieve and ESP by passing through 75 μm sieve. Compressive strength testing was conducted on concrete specimens to determine the optimum mix proportion of POFA and ESP. Generally the compressive strength of OPC concrete is higher compared to POFA-ESP concrete. Based on the results of POFA-ESP concrete overall, it shows that the optimum mix proportion of concrete is 6%POFA:4% ESP achieved compressive strength of 38.60 N/mm2 at 28 days. The compressive strength of OPC concrete for the same period was 42.37 N/mm2. Higher water demand in concrete is needed due to low fineness of POFA that contributing to low compressive strength of POFA-ESP concrete. However, the compressive strength and workability of the POFA-ESP concrete were within the ranges typically encountered in regular concrete mixtures indicating the viability of this replacement procedure for structural and non-structural applications.

Palm Oil Fuel Ash (POFA) and Eggshell Powder (ESP) as Partial Replacement for Cement in Concrete

Science.gov (United States)

Ezdiani Mohamad, Mazizah; Mahmood, Ali A.; Min, Alicia Yik Yee; Nur Nadhira A., R.

2018-03-01

This study is an attempt to partially replace Ordinary Portland cement (OPC) in concrete with palm oil fuel ash (POFA) and eggshell powder (ESP). The mix proportions of POFA and ESP were varied at 10% of cement replacement and compared with OPC concrete as control specimen. The fineness of POFA is characterized by passing through 300 μm sieve and ESP by passing through 75 μm sieve. Compressive strength testing was conducted on concrete specimens to determine the optimum mix proportion of POFA and ESP. Generally the compressive strength of OPC concrete is higher compared to POFA-ESP concrete. Based on the results of POFA-ESP concrete overall, it shows that the optimum mix proportion of concrete is 6%POFA:4% ESP achieved compressive strength of 38.60 N/mm2 at 28 days. The compressive strength of OPC concrete for the same period was 42.37 N/mm2. Higher water demand in concrete is needed due to low fineness of POFA that contributing to low compressive strength of POFA-ESP concrete. However, the compressive strength and workability of the POFA-ESP concrete were within the ranges typically encountered in regular concrete mixtures indicating the viability of this replacement procedure for structural and non-structural applications.

First international ash marketing and technology conference

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

A total of 42 papers were presented in sessions with the following headings: production and disposal of ash - an international review; environmental, health, safety, and legal aspects of ash handling; marketing of ash; development of new uses for ash; cementitious use of ash; ash in manufactured products; and geotechnical uses of ash.

Determining ash content in flotation wastes by means of the MPOF optical ash meter. [Poland

Energy Technology Data Exchange (ETDEWEB)

Sikora, T; Sliwa, J

1982-03-01

The paper evaluates an experimental unit of the MPOF optical ash meter, developed by the EMAG Research and Production Center for Electrical Engineering and Mining Automation. The MPOF, which is being tested at the coal preparation plant of the 30 lecia PRL mine, is the first system for continuous determination of ash content in flotation tailings developed in Poland. A block scheme of the system is given. It consists of a measuring head and electronic system which processes data supplied by the measuring head and calculates ash content. System operation is based on the principle of determining ash content in a mixture of coal and mineral wastes by measuring mixture reflectivity. Determining ash content in the mixture is possible as reflectivity coefficients for coal and ash are constant. Performance of the MPOF optical ash meter is evaluated; the results are shown in a table and a scheme. Measurement accuracy is satisfactory.

Exploring evaluation to influence the quality of pulverized coal fly ash. Co-firing of biomass in a pulverized coal plant or mixing of biomass ashes with pulverized coal fly ash; Verkennende evaluatie kwaliteitsbeinvloeding poederkoolvliegas. Bijstoken van biomassa in een poederkoolcentrale of bijmenging van biomassa-assen met poederkoolvliegas

Energy Technology Data Exchange (ETDEWEB)

Van der Sloot, H.A.; Cnubben, P.A.J.P [ECN Schoon Fossiel, Petten (Netherlands)

2000-08-01

(refuse derived fuels), will most likely lead to increased leaching. This will be more prominent for oxyanions than for metals. In the evaluation of the application of coal fly ash in cement production or in partial cement replacement, it is important to assess the materials behaviour in recycling stages in unbound form besides its leaching behaviour of the intact product in its service life. This aspect has not been addressed before. If a material performs poorly from an environmental point of view in its recycling stages, one should be more critical in allowing (too) high levels of co-firing or too high mixing ratios of biomass. In general, the oxyanions will be more critical than most metals. The variability in several types of biomass is rather high. This holds limitations for plant operation and availability. Premixing of biomass during size reduction leads to more consistent input and thus to more constant ash quality. Co-firing may lead to increased Cr-VI levels in the fly ash due to oxidation of Cr, which is more prominently present in flue gas upon biomass co-firing than in case of regular coal firing. Elevated Cr-VI levels are more leachable. The following recommendations have been made: measurement of leaching behaviour of coal fly ash from co-firing of different biomass streams with a special emphasis on Cr-VI leachability; measurement of flue gas quality relative to pure coal combustion during co-firing of contaminated biomass streams; verification of durability of cement-based products containing coal fly ash with ash from biomass; evaluation of the leaching behaviour of recycling products from the primary uses of biomass ash or fly ash. 35 refs.

The use of tetragnathid spiders as bioindicators of metal exposure at a coal ash spill site.

Science.gov (United States)

Otter, Ryan R; Hayden, Mary; Mathews, Teresa; Fortner, Allison; Bailey, Frank C

2013-09-01

On 22 December 2008, a dike containing coal fly ash from the Tennessee Valley Authority Kingston Fossil Fuel Plant (TN, USA) failed, resulting in the largest coal ash spill in US history. The present study was designed to determine sediment metal concentrations at multiple site locations and to determine whether site-specific bioaccumulation of metals existed in tetragnathid spiders. Selenium and nickel were the only 2 metals to exceed the US Environmental Protection Agency sediment screening levels. Selenium concentrations in spiders were significantly higher at ash-affected sites than in those from reference sites. The ratio of methylmercury to total mercury in spiders was found to be similar to that in other organisms (65-75%), which highlights the potential use of tetragnathid spiders as an indicator species for tracing contaminant transfer between the aquatic and terrestrial ecosystems. Copyright © 2013 SETAC.

Co-combustion of sewage sludge and energy-rich waste fuels or forest fuels; Sameldning av roetslam och energirika avfallsbraenslen eller skogsbraenslen

Energy Technology Data Exchange (ETDEWEB)

Linder, Kristina [TPS Termiska Processer AB, Nykoeping (Sweden)

2003-10-01

In this report literature on incineration of sewage sludge is summarises. In Sweden there is a yearly production of about 0,24 million-ton dry sewage sludge of which 50% is deposited. Recent changes in legislation will restrict and later prohibit the dumping of sewage sludge. Alternative methods for handling the material have not yet been found. In other parts of Europe the problem has been solved by incineration. Sludge incineration can be performed in several ways depending of the pretreatment. The sludge can be raw or digested, dewatered or dried. The sludge can be burnt as single fuel or in mixtures with other fuels. Focus in this work has been on co-combustion with biofuel or waste, as it will make use of existing plants. Digested sludge is also of major interest as 70% of the Swedish sludge is digested. The report describes the situation both in Sweden and in the rest of Europe. Sludge has a varying quality depending on origin and treatment, which affects the combustion properties. Ash and moisture contents differ from other fuels. The heating value of sewage sludge is approximately 20 MJ/kg per dry combustible matter and the amount of organic is around 70%. Compared to forest residue and demolition wood, sludge contains high levels of nitrogen and sulphur, which will cause emissions. The nitrogen level is about 10 times higher and the sulphur level 25 to 50 times higher. Sulphur, in combination with alkali metals, can cause deposit problems in boilers. However, sludge contains low levels of alkali. In the experimental investigation leaching of digested sludge showed low values on water conductivity which indicates a low concentration of sintering ash species in the sludge. A comparison of the aerodynamic properties of dried digested sludge and wood chips from energy coppice showed that sludge has a lower fraction of fines. This indicates that the sewage sludge is not likely to be carried over in the furnace but rather to stay in the fuel and ash bed on the

Biotic and abiotic factors affect green ash volatile production and emerald ash borer adult feeding preference.

Science.gov (United States)

Chen, Yigen; Poland, Therese M

2009-12-01

The emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), is an exotic woodborer first detected in 2002 in Michigan and Ontario and is threatening the ash resource in North America. We examined the effects of light exposure and girdling on green ash (Fraxinus pennsylvanica Marsh) volatile production, and effects of light exposure, girdling, and leaf age on emerald ash borer adult feeding preferences and phototaxis. Green ash seedlings grown under higher light exposure had lower amounts of three individual volatile compounds, (Z)-3-hexenol, (E)-beta-ocimene, and (Z,E)-alpha-farnesene, as well as the total amount of six detected volatile compounds. Girdling did not affect the levels of these volatiles. Emerald ash borer females preferred mature leaves, leaves from girdled trees, and leaves grown in the sun over young leaves, leaves from nongirdled trees, and leaves grown in the shade, respectively. These emerald ash borer preferences were most likely because of physical, nutritional, or biochemical changes in leaves in response to the different treatments. Emerald ash borer females and males showed positive phototaxis in laboratory arenas, a response consistent with emerald ash borer preference for host trees growing in sunlight.

10 Risk to Ash from Emerald Ash Borer: Can Biological Control Prevent the Loss of Ash Stands

Science.gov (United States)

Ash trees were once relatively free of serious, major diseases and insect pests in North America until the arrival of EAB, which was first detected in North America in Michigan in 2002. As of February 2014, EAB had been detected in 22 U.S. states and two Canadian provinces, killing millions of ash ...

Processed bottom ash for replacing fine aggregate in making high-volume fly ash concrete

OpenAIRE

Antoni; Sulistio Aldi Vincent; Wahjudi Samuel; Hardjito Djwantoro; Hardjito Djwantoro

2017-01-01

Bottom ash is a coal plant by-product that is abundant and underutilized. There is the potential use of bottom ash as a fine aggregate replacement in concrete mixtures; however, the problems of water absorption and uniformity of quality of the material need to be overcome first. In this study, bottom ash was treated by sieve separation and pounding to smaller particle size for use as a sand substitute. The physical and chemical characteristics of bottom ash were tested after treatment includi...

The influence of design and fuel parameters on the particle emissions from wood pellets combustion. Final report

Energy Technology Data Exchange (ETDEWEB)

Wiinikka, Henrik; Gebart, Rikard [Energy Technology Centre, Piteaa (Sweden)

2005-02-01

Combustion of solid biomass under fixed bed conditions is a common technique to generate heat and power in both small and large scale grate furnaces (domestic boilers, stoves, district heating plants). Unfortunately, combustion of biomass will generate particle emissions containing both large fly ash particles and fine particles that consist of fly ash and soot. The large fly ash particles have been produced from fusion of non-volatile ash-forming species in burning char particle. The inorganic fine particles have been produced from nucleation of volatilised ash elements (K, Na, S, Cl and Zn). If the combustion is incomplete, soot particles are also produced from secondary reaction of tar. The particles in the fine fraction grows by coagulation and coalescence to a particle diameter around 0.1 pm. Since the smallest particles are very hard to collect in ordinary cleaning devices they contribute to the ambient air pollution. Furthermore, fine airborne particles have been correlated to adverse effects on the human health. It is therefore essential to minimize particle formation from the combustion process and thereby reduce the emissions of particulates to the ambient air. The aim with this project is to study particle emissions from small scale combustion of wood pellets and to investigate the impact of different operating, construction and fuel parameters on the amount and characteristic of the combustion generated particles. To address these issues, experiments were carried out in a 10 kW updraft fired wood pellets reactor that has been custom designed for systematic investigations of particle emissions. In the flue gas stack, particle emissions were sampled on a filter. The particle mass and number size distributions were analysed by a low pressure cascade impactor and a SMPS (Scanning Electron Mobility Particle Sizer). The results showed that the temperature and the flow pattern in the combustion zone affect the particle emissions. Increasing combustion

Characterization of metals released from coal fly ash during dredging at the Kingston ash recovery project.

Science.gov (United States)

Bednar, A J; Averett, D E; Seiter, J M; Lafferty, B; Jones, W T; Hayes, C A; Chappell, M A; Clarke, J U; Steevens, J A

2013-09-01

A storage-pond dike failure occurred on December 22, 2008 at the Tennessee Valley Authority Kingston Fossil Plant resulting in the release of over 4million cubic meters (5million cubic yards) of fly ash. Approximately half of the released ash was deposited in the main channel of the Emory River, Tennessee, USA. Remediation efforts of the Emory River focused on hydraulic dredging, as well as mechanical excavation in targeted areas. However, agitation of the submerged fly ash during hydraulic dredging introduces river water into the fly ash material, which could promote dissolution and desorption of metals from the solid fly ash material. Furthermore, aeration of the dredge slurry could alter the redox state of metals in the fly ash material and thereby change their sorption, mobility, and toxicity properties. The research presented here focuses on the concentrations and speciation of metals during the fly ash recovery from the Emory River. Our results indicate that arsenite [As(III)] released from the fly ash material during dredging was slowly oxidized to arsenate [As(V)] in the slurry recovery system with subsequent removal through precipitation or sorption reactions with suspended fly ash material. Concentrations of other dissolved metals, including iron and manganese, also generally decreased in the ash recovery system prior to water discharge back to the river. Published by Elsevier Ltd.

Prospects for ash pond reclamation

Energy Technology Data Exchange (ETDEWEB)

Shyyam, A.K.; Shukla, K.S.; Agrawal, D. (National Thermal Power Corporation Ltd., New Delhi (India))

1993-01-01

A typical modern coal fired station in India burns 0.7 t/MWh of coal and consequently generates ash at 0.245 t/MWh. The physical nature of ash, low available concentrations of certain plant nutrients and the presence of phytotoxic trace elements render fly ash marginally adequate for plant growth. As fly ash itself was thought to be an inappropriate growth medium for plants, regulators decided that a soil cover is mandatory. There is ample data to suggest that the attributes of fly ash detrimental to plant growth can be ameliorated, allowing the establishment of vegetation directly on fly ash surfaces. The natural revegetation of fly ash disposal sites has been reported in the world. The natural vegetation pioneered by Cynodon at different stages of ecological succession and comprising of species such as [ital Calotropis gigantea], [ital Lippia nodiflora], [ital Ipomea, cornea], [ital Xanthium parviflorum] has been noted at one of the NTPC projects, in Badarpur Thermal Power Station. Since natural reclamation is a time-consuming process, experimental trials of growing some species over the temporary ash lagoon directly (without soil cover) were carried out at Ramagundam Super Thermal Power Project (RSTPP) of NTPC, in South India to achieve faster results than the natural process. 6 refs., 8 figs.

Characterization of Fly and Bottom Ashes Mixtures Treated using Sodium Lauryl Sulphate and Polyvinyl Alcohol

Science.gov (United States)

Robert, C. G.; Ayob, A.; Zaki, M. F. Muhammad; Razali, M. E.; Lew, E. V.; Hong, P. Y.

2018-03-01

Malaysia promotes coal as an option for solid fuel in electric power generation. Demanding of electricity needs, therefore, has led to increase the coal consumption and thus producing more coal waste products. The disposal of coal waste ashes has been a main concern to power generation station due to the need of disposal sites and operational costs. This study investigates the composition of fly ash (FA) and bottom ash (BA) mixtures with difference component percentage treated with sodium lauryl sulphate (SLS) and polyvinyl alcohol (PVA) at 1.5 and 2.5 wt% solutions and examined in terms of specific gravity, pH, maximum dry density properties, and its surface morphology. Although the chemical composition of the SLS and PVA treated fly and bottom ashes studied in this current work is not altered extensively, significant changes could be observed in its physicochemical properties. Chemically treated fly and bottom ashes mixtures with SLS and PVA at 1.5 wt% solution exhibited specific gravity of 1.97 to 2.92 and high pH values within range of 9.28 to 10.52. The mixture of BA:FA=0:1 ratio depicting high maximum dry density of 1.35 to 1.56 g/cm3 in both SLS and PVA solutions at 1.5 and 2.5 wt%. Scanning electron microscopy image shows distinct surface morphologies of SLS-treated fly and bottom ashes mixture that the particles are packed closely, strongly bonded similar to popcorn shape due to the effect of active silanol groups acted on coal ashes surface with the presence of Al-O/Si-O/other oxides. These findings suggest that higher level of chemical interaction between the fly and bottom ashes particles, significantly enhances pozzolanic reactions such as shear strength, plasticity, cementing properties, and thus other engineering properties.

Characterization of Fly and Bottom Ashes Mixtures Treated using Sodium Lauryl Sulphate and Polyvinyl Alcohol

Directory of Open Access Journals (Sweden)

Robert C.G.

2018-01-01

Full Text Available Malaysia promotes coal as an option for solid fuel in electric power generation. Demanding of electricity needs, therefore, has led to increase the coal consumption and thus producing more coal waste products. The disposal of coal waste ashes has been a main concern to power generation station due to the need of disposal sites and operational costs. This study investigates the composition of fly ash (FA and bottom ash (BA mixtures with difference component percentage treated with sodium lauryl sulphate (SLS and polyvinyl alcohol (PVA at 1.5 and 2.5 wt% solutions and examined in terms of specific gravity, pH, maximum dry density properties, and its surface morphology. Although the chemical composition of the SLS and PVA treated fly and bottom ashes studied in this current work is not altered extensively, significant changes could be observed in its physicochemical properties. Chemically treated fly and bottom ashes mixtures with SLS and PVA at 1.5 wt% solution exhibited specific gravity of 1.97 to 2.92 and high pH values within range of 9.28 to 10.52. The mixture of BA:FA=0:1 ratio depicting high maximum dry density of 1.35 to 1.56 g/cm3 in both SLS and PVA solutions at 1.5 and 2.5 wt%. Scanning electron microscopy image shows distinct surface morphologies of SLS-treated fly and bottom ashes mixture that the particles are packed closely, strongly bonded similar to popcorn shape due to the effect of active silanol groups acted on coal ashes surface with the presence of Al-O/Si-O/other oxides. These findings suggest that higher level of chemical interaction between the fly and bottom ashes particles, significantly enhances pozzolanic reactions such as shear strength, plasticity, cementing properties, and thus other engineering properties.

Bioleaching of trace metals from coal ash using local isolate from coal ash ponds

Directory of Open Access Journals (Sweden)

Pangayao Denvert

2018-01-01

Full Text Available Bioleaching of chromium, copper, manganese and zinc from coal ash were investigated using isolates from coal ash ponds particularly Psuedomonas spp. Six (6 different coal ash ponds were examined however, after initial screening Psuedomonas spp. were only present in three (3 coal ash ponds. Among the three coal ash ponds, results showed that eight (8 putative Pseudomonas spp. isolates were present that were identified using the Polymerase Chain Reaction (PCR. Using the eight putative Pseudomonas spp. for bioleaching at optimum conditions and 15 days, the pH value ranges from 8.26 to 8.84 which was basic in nature. Moreover, the maximum metal leached were 8.04% Cr, 12.05% Cu, 4.34% Mn and 10.63% Zn.

Formation of chlorinated organic compounds in fluidized bed combustion of recycled fuels; Kloorattujen orgaanisten yhdisteiden muodostuminen kierraetyspolttoaineiden leijukerrospoltossa

Energy Technology Data Exchange (ETDEWEB)

Vesterinen, R.; Kallio, M.; Kirjalainen, T.; Kolsi, A.; Merta, M. [VTT Energy, Jyvaeskylae (Finland)

1997-10-01

Four tests of co-combustion of recycled fuels (REP) with peat and coal in the 15 kW fluidized bed reactor were performed. The recycled fuel was so-called dry fraction in four vessels sampling at Keltinmaeki. In three tests a part of peat energy was replaced with coal. The mixtures were prepared so that in all mixtures 25 % of energy was recycled fuel and 75 % was either peat or the mixture of peat and coal. The concentrations of polyaromatic hydrocarbons (PAH), polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) and chlorophenols decreased with increasing part of coal due to the increasing sulphur/chlorine ratio. Principal Component Analysis (PCA) and Partial Least Square regression analysis (PLS) showed that the chlorine, copper and sulphur contents of the fuel effected most on the concentrations of chlorophenols, chlorobenzenes, PCBs and PCDDs/PCDFs. Other variables influencing on a model were the lead concentration and the sulphur/chlorine ratio in fuel and the hydrogen chloride concentration of the flue gas. The concentrations of chlorophenols and chlorobenzenes were also significant for PCDD/PCDF concentrations in flue gas. The sulphur, chlorine, copper and chromium contents in fly ash and the temperature of the reactor influenced on the chlorophenol, chlorobenzene, PCB and PCDD/PCDF concentrations in fly ash. The chlorophenol and chlorobenzene contents in fly ash, the sulphur/chlorine ratio and the lead content in fuel, the sulphur dioxide, hydrogen chloride and carbon monoxide concentrations in flue gas had also influence on PCDD/PCDF concentrations in fly ash

Solid fuels - A round robin test of solid residual products from heating plants. Fasta braenslen - cirkelanalys av fasta restprodukter fraan foerbraenningsanlaeggningar

Energy Technology Data Exchange (ETDEWEB)

Burwall, J; Samuelsson, R [Sveriges Lanbruksuniversitet, Enheten foer Biomassa, Energi- och Fibergroedor, Umeaa (Sweden)

1992-03-01

A round robin test, where six ashes (three coal ashes and three bioashes) were analyzed with respect to 'fuelspecific' parameters, major and minor elements and trace elements, has been carried out. Thirteen laboratories from Sweden, Finland, Denmark and Norway participated and the purpose of the investigation was to compare and evaluate common methods of analysis for ashes. The standard deviation of the used methods was compared to the precision calculated from the reported reproducability in corresponding standard methods for fuels. The results show that, without taking the significant outliers into account, the precision of the analysis of moisture content, hydrogen, nitrogen, sulfur and the predominant part of major and minor elements was of the order of the corresponding analysis for fuels. The analysis of carbon and calorific value showed a variation somewhat higher than that for fuel analysis, while the results for volatile matter and the tracer elements were considerably less precise. The result for the amount of unburned matter showed significant groupings, not only between the ashes but also between the laboratories. The groupings were explained mainly by the different experimental parameters used during the ashing step. (au) (5 refs., 10 figs., 38 tabs.).

Solid fuels - A round robin test of solid residual products from heating plants; Fasta braenslen - cirkelanalys av fasta restprodukter fraan foerbraenningsanlaeggningar

Energy Technology Data Exchange (ETDEWEB)

Burwall, J; Samuelsson, R [Sveriges Lanbruksuniversitet, Enheten foer Biomassa, Energi- och Fibergroedor, Umeaa (Sweden)

1992-03-01

A round robin test, where six ashes (three coal ashes and three bioashes) were analyzed with respect to `fuelspecific` parameters, major and minor elements and trace elements, has been carried out. Thirteen laboratories from Sweden, Finland, Denmark and Norway participated and the purpose of the investigation was to compare and evaluate common methods of analysis for ashes. The standard deviation of the used methods was compared to the precision calculated from the reported reproducability in corresponding standard methods for fuels. The results show that, without taking the significant outliers into account, the precision of the analysis of moisture content, hydrogen, nitrogen, sulfur and the predominant part of major and minor elements was of the order of the corresponding analysis for fuels. The analysis of carbon and calorific value showed a variation somewhat higher than that for fuel analysis, while the results for volatile matter and the tracer elements were considerably less precise. The result for the amount of unburned matter showed significant groupings, not only between the ashes but also between the laboratories. The groupings were explained mainly by the different experimental parameters used during the ashing step. (au) (5 refs., 10 figs., 38 tabs.).

Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash

Directory of Open Access Journals (Sweden)

Martin Ernesto Kalaw

2016-07-01

Full Text Available Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC, which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1 their technical properties are comparable if not better; (2 they can be produced from industrial wastes; and (3 within reasonable constraints, their production requires less energy and emits significantly less CO2. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA and coal bottom ash (CBA, and rice hull ash (RHA. The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF for elemental and X-ray diffraction (XRD for mineralogical composition. The raw materials’ thermal stability and loss on ignition (LOI were determined using thermogravimetric analysis (TGA and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR

Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash.

Science.gov (United States)

Kalaw, Martin Ernesto; Culaba, Alvin; Hinode, Hirofumi; Kurniawan, Winarto; Gallardo, Susan; Promentilla, Michael Angelo

2016-07-15

Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC), which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1) their technical properties are comparable if not better; (2) they can be produced from industrial wastes; and (3) within reasonable constraints, their production requires less energy and emits significantly less CO₂. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC) use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA) and coal bottom ash (CBA), and rice hull ash (RHA). The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF) for elemental and X-ray diffraction (XRD) for mineralogical composition. The raw materials' thermal stability and loss on ignition (LOI) were determined using thermogravimetric analysis (TGA) and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP) analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR), scanning

Effects of the addition of oil shale ash and coal ash on physic-chemical properties of CPJ45 cement

Directory of Open Access Journals (Sweden)

Nabih K.

2014-04-01

Full Text Available We focused our research on recycling industrial wastes, fly ash (F.A, bottom ash (B.A and oil shale ash (S.A in cement production. The study concerns physico-chemical characterization of these products and the influence of their addition on the mechanical proprieties of the CPJ45 cement. XRF allowed us to rank the three additives used according to their contents on major oxides. Coal ashes belong to the class F, and thus possess poozzolanic properties and oil shale ash belongs to the class C and possesses hydraulic and poozolanic properties. The crystalline phases constituting each ash were analysed by XRD. We observe in bottom ash the presence of quartz and mullite. The same crystals are found in fly ash with hematite and magnetite. Oil shale ash is composed of quartz, anhydrite, gehlenite, wollastonite and periclase. The microstructures of fly ash and bottom ash were studied using SEM. The bottom ash was composed respectively of fine particles that are generally irregularly shaped, their dimensions are between 5 and 28μm and of big particles(300 μm. The EDX analysis coupled with an electronic microscope provided some information about the major elements that constitute our samples. The dehydrations of anhydrous and three days hydrated cement were examined by DSC. For hydrated cements we noticed endothermic peaks related to the dehydration of CSH, CH and decomposition of carbonates. The study of the mechanical properties of CPJ45 cement by adding different proportions of fly ash, bottom ash and oil shale ash helped clarifying the percentage of ash that leaded to improve the 28 days mechanical strength. The results show that the cements studied have their maximum mechanical resistance with the addition at 7% of fly ash or 10% of oil shale ash.

Fly ash dynamics in soil-water systems

International Nuclear Information System (INIS)

Sharma, S.; Fulekar, M.H.; Jayalakshmi, C.P.

1989-01-01

Studies regarding the effluents and coal ashes (or fly ash) resulting from coal burning are numerous, but their disposal and interactions with the soil and water systems and their detailed environmental impact assessment with concrete status reports on a global scale are scanty. Fly ash dynamics in soil and water systems are reviewed. After detailing the physical composition of fly ash, physicochemical changes in soil properties due to fly ash amendment are summarized. Areas covered include texture and bulk density, moisture retention, change in chemical equilibria, and effects of fly ash on soil microorganisms. Plant growth in amended soils is discussed, as well as plant uptake and accumulation of trace elements. In order to analyze the effect of fly ash on the physicochemical properties of water, several factors must be considered, including surface morphology of fly ash, pH of the ash sluice water, pH adjustments, leachability and solubility, and suspended ash and settling. The dynamics of fly ash in water systems is important due to pollution of groundwater resources from toxic components such as trace metals. Other factors summarized are bioaccumulation and biomagnification, human health effects of contaminants, and the impact of radionuclides in fly ash. Future research needs should focus on reduction of the environmental impact of fly ash and increasing utilization of fly ash as a soil amendment. 110 refs., 2 figs., 10 tabs

Techno-economic analysis of PC versus CFB combustion technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-10-01

In the last ten years circulating fluidised bed combustion (CFBC) has emerged as a viable alternative to pulverised coal combustion (PCC) for utility-scale coal power generation, with widespread deployment of 300 MW boilers and the successful demonstration of supercritical units of up to 600 MW. Although CFBC offers a greater degree of fuel flexibility and does not usually require downstream flue gas cleaning, high capital costs and high auxiliary power use have hindered the adoption of CFBC for utility power generation. Recent advances in CFBC unit capacity and steam conditions have led to higher efficiencies and economies of scale, with the result that a CFBC plant may now be more economically favourable than a PCC plant depending on a range of factors such as available fuels and regional emissions limits. This report reviews the state-of-the-art for both technologies and provides a comparison of their relative performances and economic costs. Standard operational parameters such as efficiency, availability, and flexibility are assessed, in addition to relative suitability for biomass cofiring and oxyfuel combustion as strategies for carbon mitigation. A review of recent cost evaluations of the two technologies is accompanied by a breakdown of individual plant expenses including flue gas scrubbing equipment and ash recycle value.

Fly ash quality and utilization

Energy Technology Data Exchange (ETDEWEB)

Barta, L.E.; Lachner, L.; Wenzel, G.B. [Inst. for Energy, Budapest (Hungary); Beer, M.J. [Massachusetts Inst. of Technology, Cambridge, MA (United States)

1995-12-01

The quality of fly ash is of considerable importance to fly ash utilizers. The fly ash puzzolanic activity is one of the most important properties that determines the role of fly ash as a binding agent in the cementing process. The puzzolanic activity, however is a function of fly ash particle size and chemical composition. These parameters are closely related to the process of fly ash formation in pulverized coal fired furnaces. In turn, it is essential to understand the transformation of mineral matter during coal combustion. Due to the particle-to-particle variation of coal properties and the random coalescence of mineral particles, the properties of fly ash particles e.g. size, SiO{sub 2} content, viscosity can change considerably from particle to particle. These variations can be described by the use of the probability theory. Since the mean values of these randomly changing parameters are not sufficient to describe the behavior of individual fly ash particles during the formation of concrete, therefore it is necessary to investigate the distribution of these variables. Examples of these variations were examined by the Computer Controlled Scanning Electron Microscopy (CCSEM) for particle size and chemical composition for Texas lignite and Eagel Butte mineral matter and fly ash. The effect of combustion on the variations of these properties for both the fly ash and mineral matter were studied by using a laminar flow reactor. It is shown in our paper, that there are significant variations (about 40-50% around the mean values) of the above-listed properties for both coal samples. By comparing the particle size and chemical composition distributions of the mineral matter and fly ash, it was possible to conclude that for the Texas lignite mineral matter, the combustion did not effect significantly the distribution of these properties, however, for the Eagel Butte coal the combustion had a major impact on these mineral matter parameters.

Ash cloud aviation advisories

Energy Technology Data Exchange (ETDEWEB)

Sullivan, T.J.; Ellis, J.S. [Lawrence Livermore National Lab., CA (United States); Schalk, W.W.; Nasstrom, J.S. [EG and G, Inc., Pleasanton, CA (United States)

1992-06-25

During the recent (12--22 June 1991) Mount Pinatubo volcano eruptions, the US Air Force Global Weather Central (AFGWC) requested assistance of the US Department of Energy`s Atmospheric Release Advisory Capability (ARAC) in creating volcanic ash cloud aviation advisories for the region of the Philippine Islands. Through application of its three-dimensional material transport and diffusion models using AFGWC meteorological analysis and forecast wind fields ARAC developed extensive analysis and 12-hourly forecast ash cloud position advisories extending to 48 hours for a period of five days. The advisories consisted of ``relative`` ash cloud concentrations in ten layers (surface-5,000 feet, 5,000--10,000 feet and every 10,000 feet to 90,000 feet). The ash was represented as a log-normal size distribution of 10--200 {mu}m diameter solid particles. Size-dependent ``ashfall`` was simulated over time as the eruption clouds dispersed. Except for an internal experimental attempt to model one of the Mount Redoubt, Alaska, eruptions (12/89), ARAC had no prior experience in modeling volcanic eruption ash hazards. For the cataclysmic eruption of 15--16 June, the complex three-dimensional atmospheric structure of the region produced dramatically divergent ash cloud patterns. The large eruptions (> 7--10 km) produced ash plume clouds with strong westward transport over the South China Sea, Southeast Asia, India and beyond. The low-level eruptions (< 7 km) and quasi-steady-state venting produced a plume which generally dispersed to the north and east throughout the support period. Modeling the sequence of eruptions presented a unique challenge. Although the initial approach proved viable, further refinement is necessary and possible. A distinct need exists to quantify eruptions consistently such that ``relative`` ash concentrations relate to specific aviation hazard categories.

Identifying glass compositions in fly ash

Directory of Open Access Journals (Sweden)

Katherine eAughenbaugh

2016-01-01

Full Text Available In this study, four Class F fly ashes were studied with a scanning electron microscope; the glassy phases were identified and their compositions quantified using point compositional analysis with k-means clustering and multispectral image analysis. The results showed that while the bulk oxide contents of the fly ashes were different, the four fly ashes had somewhat similar glassy phase compositions. Aluminosilicate glasses (AS, calcium aluminosilicate glasses (CAS, a mixed glass, and, in one case, a high iron glass were identified in the fly ashes. Quartz and iron crystalline phases were identified in each fly ash as well. The compositions of the three main glasses identified, AS, CAS, and mixed glass, were relatively similar in each ash. The amounts of each glass were varied by fly ash, with the highest calcium fly ash containing the most of calcium-containing glass. Some of the glasses were identified as intermixed in individual particles, particularly the calcium-containing glasses. Finally, the smallest particles in the fly ashes, with the most surface area available to react in alkaline solution, such as when mixed with portland cement or in alkali-activated fly ash, were not different in composition than the large particles, with each of the glasses represented. The method used in the study may be applied to a fly ash of interest for use as a cementing material in order to understand its potential for reactivity.

Small-scale bio fuelled heat and power - requirements for standardized technical and fuel solutions from a systems perspective; Smaaskalig biobraenslebaserad kraftvaerme - foerutsaettningar foer standardiserade loesningar med avseende paa teknik och braenslen i ett systemperspektiv

Energy Technology Data Exchange (ETDEWEB)

Nystroem, Olle; Johansson, Kent; Steinwall, Pontus [Sycon Energikonsult AB, Malmoe (Sweden)

2001-01-01

Different techniques for small-scale heat and power generation have been investigated. The included cycles are steam turbine, diesel engine, Otto engine, Stirling engine, gas turbine and organic Rankine cycle (ORC). For steam turbines, Stirling engine, and indirectly fired gas turbines, the combustion can be placed in a relatively conventional furnace, which gives a fairly free choice of fuel. In other cycles like the traditional gas turbine cycle, diesel engine and Otto engine, the fuel should be in the gas or liquid phase. Experiments are in progress to use wood pf (pulverised fuel) as fuel. The technique for plants based on steam turbine, diesel engine, Otto engine, conventional gas turbine and ORC based on different forms of bio fuel exist already today. For Stirling engine, gas turbine with HAT cycle (Humid Air Turbine) and indirectly fired gas turbine further development is needed before the technique will be commercially available using bio fuel. An interesting process coupling is a gas engine combined with a gasifier. This coupling can be a competitive choice to the other processes if the problems with gas cleaning can be solved.

Characterisation of ashes produced by co-combustion of recovered fuels and peat

Energy Technology Data Exchange (ETDEWEB)

Frankenhaeuser, M.; Zevenhoven, R. [Borealis Polymers Oy, Porvoo (Finland); Skrifvars, B.J. [Aabo Akademi, Turku (Finland); Orjala, M. [VTT Energy, Espoo (Finland); Peltola, K. [Foster Wheeler Energy (Finland)

1996-12-01

Source separation of combustible materials from household or municipal solid waste yields a raw material for the production of Packaging Derived Fuel (PDF). This fuel can substitute the traditional fuels in heat and power generation and is also called recycled fuel. Co-combustion of these types of fuels with coal has been studied in several LIEKKI-projects and the results have been both technically and environmentally favourable. (author)

The Role of Biocontrol of Emerald Ash Borer in Protecting Ash Regeneration after Invasion

Science.gov (United States)

Emerald ash borer (EAB) is an invasive Asian beetle that is destroying ash in forests over much of eastern North America because of the high susceptibility of our native ash and a lack of effective natural enemies. To increase mortality of EAB larvae and eggs, the USDA (FS, ARS and APHIS) is carryin...

Reactivity and burnout of wood fuels

Energy Technology Data Exchange (ETDEWEB)

Dall' Ora, M.

2011-07-01

This thesis deals with the combustion of wood in pulverised fuel power plants. In this type of boiler, the slowest step in the wood conversion process is char combustion, which is one of the factors that not only determine the degree of fuel burnout, but also affect the heat release profile in the boiler and thereby the overall operation and efficiency of the plant. Chapter 1 consists of an introduction to thermal conversion of biomass fuels as well as a description of a Danish power plant where a measuring campaign was carried out as part of this project. Chapter 2 is a brief literature review of different aspects relevant to wood combustion, including wood structure and composition, wood pyrolysis, wood char properties and wood char oxidation. The full scale campaign, which is the subject of Chapter 3, included sampling of wood fuel before and after milling and sampling of gas and particles at the top of the combustion chamber. The collected samples and data are used to obtain an evaluation of the mills in operation at the power plant, the particle size distribution of the wood fuel, as well as the char conversion attained in the furnace. In Chapter 4 an experimental investigation on the relation between pyrolysis of wood in boiler-like conditions and wood char properties is presented. Chars from pine and beech wood were produced by fast pyrolysis in an entrained flow reactor and by slow pyrolysis in a thermogravimetric analyser. The influence of pyrolysis temperature, heating rate and particle size on char yield and morphology was investigated. The applied pyrolysis temperature varied in the range 673-1673 K for slow pyrolysis and 1073-1573 K for fast pyrolysis. The chars were oxidised in a thermogravimetric analyser and the mass loss data were used to determine char oxidation reactivity. Char yield from fast pyrolysis (104-105 K/s) was as low as 1-6% on a dry ash free basis, whereas it was about 15-17% for slow pyrolysis (10-20 K/min); char yield decreased as

Heat of hydration measurements on cemented radioactive wastes. Part 1: cement-water pastes

International Nuclear Information System (INIS)

Lee, D.J.

1983-12-01

This report describes the hydration of cement pastes in terms of chemical and kinetic models. A calorimetric technique was used to measure the heat of hydration to develop these models. The effects of temperature, water/cement ratio and cement replacements, ground granulated blast furnace slag (BFS) and pulverised fuel ash (PFA) on the hydration of ordinary Portland cement (OPC) is reported. The incorporation of BFS or PFA has a marked effect on the hydration reaction. The effect of temperature is also important but changing the water/cement ratio has little effect. Results from cement pastes containing only water and cement yield total heats of reaction of 400, 200 and 100 kJ/kg for OPC, BFS and PFA respectively. Using the results from the models which have been developed, the effect of major salts present in radioactive waste streams can be assessed. Values of the total heat of reaction, the time to complete 50 percent reaction, and the energy of activation, can be compared for different waste systems. (U.K.)

The anaerobic corrosion of carbon steel in concrete

International Nuclear Information System (INIS)

Naish, C.C.; Balkwill, P.H.; O'Brien, T.M.; Taylor, K.J.; Marsh, G.P.

1990-11-01

The report describes the work of a two year programme investigating the anaerobic corrosion of carbon steel embedded in a range of candidate repository cements and concretes at laboratory ambient temperatures. The factors investigated in the study were the rate of the anaerobic corrosion reaction, the effect of hydrogen overpressure on the reaction rate and the form of the corrosion product. Both electrochemical and sample weight loss corrosion rate measurements were used. The cements and concretes used were prepared both with and without small additions of chloride (2% by weight of mix water). The results indicate that the corrosion rate is low, <1 μm/year, the effect of hydrogen overpressure is not significant over the range of pressures investigated, 1-100 atmospheres, and that the corrosion product is dependent on the cement used to cast the samples. Magnetite was identified in the case of blast furnace slag replacement cements but for pulverised fuel ash and ordinary Portland cements no corrosion product was evident either from X-ray diffraction or laser Raman measurements. (Author)

Fuel Handbook[Wood and other renewable fuels

Energy Technology Data Exchange (ETDEWEB)

Stroemberg, Birgitta [TPS Termiska Processer AB, Nykoeping (SE)] (ed.)

2006-03-15

This handbook on renewable fuels is intended for power and heat producers in Sweden. This fuel handbook provides, from a plant owner's perspective, a method to evaluate different fuels on the market. The fuel handbook concerns renewable fuels (but does not include household waste) that are available on the Swedish market today or fuels that have potential to be available within the next ten years. The handbook covers 26 different fuels. Analysis data, special properties, operating experiences and literature references are outlined for each fuel. [Special properties, operating experiences and literature references are not included in this English version] The handbook also contains: A proposed methodology for introduction of new fuels. A recommendation of analyses and tests to perform in order to reduce the risk of problems is presented. [The recommendation of analyses and tests is not included in the English version] A summary of relevant laws and taxes for energy production, with references to relevant documentation. [Only laws and taxes regarding EU are included] Theory and background to evaluate a fuel with respect to combustion, ash and corrosion properties and methods that can be used for such evaluations. Summary of standards, databases and handbooks on biomass fuels and other solid fuels, and links to web sites where further information about the fuels can be found. The appendices includes: A methodology for trial firing of fuels. Calculations procedures for, amongst others, heating value, flue gas composition, key number and free fall velocity [Free fall velocity is not included in the English version]. In addition, conversion routines between different units for a number of different applications are provided. Fuel analyses are presented in the appendix. (The report is a translation of parts of the report VARMEFORSK--911 published in 2005)

Study of a large rapid ashing apparatus and a rapid dry ashing method for biological samples and its application

International Nuclear Information System (INIS)

Jin Meisun; Wang Benli; Liu Wencang

1988-04-01

A large rapid-dry-ashing apparatus and a rapid ashing method for biological samples are described. The apparatus consists of specially made ashing furnace, gas supply system and temperature-programming control cabinet. The following adventages have been showed by ashing experiment with the above apparatus: (1) high speed of ashing and saving of electric energy; (2) The apparatus can ash a large amount of samples at a time; (3) The ashed sample is pure white (or spotless), loose and easily soluble with few content of residual char; (4) The fresh sample can also be ashed directly. The apparatus is suitable for ashing a large amount of the environmental samples containing low level radioactivity trace elements and the medical, food and agricultural research samples

Proceedings: pellet fuels conference

Energy Technology Data Exchange (ETDEWEB)

1995-12-31

The conference brought together professionals from the process- engineered-fuels (PEF), utility, paper, plastics, and boiler industries. Although the last two decades have produced technical breakthroughs, efforts to advance PEF must now focus on increasing commercial breakthroughs. Successful commercialization will depend on increasing supplier, consumer, and regulator confidence and support by demonstrating the performance and value of PEF products. Speakers provided updates on how PEF technology is evolving with respect to technical, economic, and regulatory challenges. Actions critical toward full commercialization of PEF were then considered. Discussion groups addressed materials sourcing, fuel processing and transportation, combustion, and ash handling.

Transcriptomic signatures of ash (Fraxinus spp. phloem.

Directory of Open Access Journals (Sweden)

Xiaodong Bai

2011-01-01

Full Text Available Ash (Fraxinus spp. is a dominant tree species throughout urban and forested landscapes of North America (NA. The rapid invasion of NA by emerald ash borer (Agrilus planipennis, a wood-boring beetle endemic to Eastern Asia, has resulted in the death of millions of ash trees and threatens billions more. Larvae feed primarily on phloem tissue, which girdles and kills the tree. While NA ash species including black (F. nigra, green (F. pennsylvannica and white (F. americana are highly susceptible, the Asian species Manchurian ash (F. mandshurica is resistant to A. planipennis perhaps due to their co-evolutionary history. Little is known about the molecular genetics of ash. Hence, we undertook a functional genomics approach to identify the repertoire of genes expressed in ash phloem.Using 454 pyrosequencing we obtained 58,673 high quality ash sequences from pooled phloem samples of green, white, black, blue and Manchurian ash. Intriguingly, 45% of the deduced proteins were not significantly similar to any sequences in the GenBank non-redundant database. KEGG analysis of the ash sequences revealed a high occurrence of defense related genes. Expression analysis of early regulators potentially involved in plant defense (i.e. transcription factors, calcium dependent protein kinases and a lipoxygenase 3 revealed higher mRNA levels in resistant ash compared to susceptible ash species. Lastly, we predicted a total of 1,272 single nucleotide polymorphisms and 980 microsatellite loci, among which seven microsatellite loci showed polymorphism between different ash species.The current transcriptomic data provide an invaluable resource for understanding the genetic make-up of ash phloem, the target tissue of A. planipennis. These data along with future functional studies could lead to the identification/characterization of defense genes involved in resistance of ash to A. planipennis, and in future ash breeding programs for marker development.

Spectral analysis of white ash response to emerald ash borer infestations

Science.gov (United States)

Calandra, Laura

The emerald ash borer (EAB) (Agrilus planipennis Fairmaire) is an invasive insect that has killed over 50 million ash trees in the US. The goal of this research was to establish a method to identify ash trees infested with EAB using remote sensing techniques at the leaf-level and tree crown level. First, a field-based study at the leaf-level used the range of spectral bands from the WorldView-2 sensor to determine if there was a significant difference between EAB-infested white ash (Fraxinus americana) and healthy leaves. Binary logistic regression models were developed using individual and combinations of wavelengths; the most successful model included 545 and 950 nm bands. The second half of this research employed imagery to identify healthy and EAB-infested trees, comparing pixel- and object-based methods by applying an unsupervised classification approach and a tree crown delineation algorithm, respectively. The pixel-based models attained the highest overall accuracies.

Thermal treatment of ashes[Fly Ash from Municipal Waste Incineration]; Termisk rening av askor

Energy Technology Data Exchange (ETDEWEB)

Wikman, Karin; Berg, Magnus; Bjurstroem, Henrik [AaF-Energi och Miljoe AB, Stockholm (Sweden); Nordin, Anders [Umeaa Univ. (Sweden). Dept. of Applied Physics and Electronics

2003-04-01

In this project descriptions of different processes for thermal treatment of ashes have been compiled. A technical and economic evaluation of the processes has been done to identify possibilities and problems. The focus in the project lays on treatment of fly ash from municipal waste incineration but the processes can also be used to treat other ashes. When the ash is heated in the thermal treatment reactor, with or without additives, the material is sintered or vitrified and at the same time volatile substances (Zn, Pb, Cd, Hg etc.) are separated. In general the separation is more effective in processes with reducing conditions compared to oxidizing conditions. Oxidizing processes have both worse separation capacity and require more energy. The oxidizing processes are mainly used to stabilize the ash through vitrification and they are in some cases developed for management of municipal sewage sludge and bottom ash. However, these processes are often not as complex as for example an electric arc melting furnace with reducing conditions. The research today aim to develop more effective electrical melting systems with reducing conditions such as plasma melting furnaces, electric resistance melting furnaces and low frequency induction furnaces. A central question in the evaluation of different thermal treatment processes for ash is how the residues from the treatment can be used. It is not certain that the vitrified material is stable enough to get a high economic value, but it can probably be used as construction material. How the remaining metals in the ash are bound is very important in a long-time perspective. Further studies with leaching tests are necessary to clarify this issue. The heavy metal concentrate from the processes contains impurities, such as chlorine, which makes it unprofitable to obtain the metals. Instead the heavy metal concentrate has to be land filled. However, the amount of material for land filling will be much smaller if only the heavy

Release to the Gas Phase of Inorganic Elements during Wood Combustion. Part 2: Influence of Fuel Composition

DEFF Research Database (Denmark)

van Lith, Simone Cornelia; Jensen, Peter Arendt; Frandsen, Flemming

2008-01-01

temperatures in the range of 500–1150 °C in a laboratory-scale tube reactor and by performing mass balance calculations based on the weight measurements and chemical analyses of the wood fuels and the residual ash samples. Four wood fuels with different ash contents and inorganic compositions were investigated...... of the alkali metals K and Na was, however, strongly dependent on both the temperature and the fuel composition under the investigated conditions. The release of the heavy metals Zn and Pb started around 500 °C and increased sharply to more than 85% at 850 °C in the case of spruce, beech, and bark...

Application of Coal Ash to Postmine Land for Prevention of Soil Erosion in Coal Mine in Indonesia: Utilization of Fly Ash and Bottom Ash

Directory of Open Access Journals (Sweden)

Shinji Matsumoto

2016-01-01

Full Text Available The increase in the number of coal-fired power plants with the increase in coal production and its consumption has caused the problem of the treatment of a large amount of coal ash in Indonesia. In the past studies, coal ash was applied to postmine land with the aim of improving soil conditions for plant growth; however, heavy rain in the tropical climate may cause soil erosion with the change in soil conditions. This study presents the effects of application of coal ash to postmine land on soil erosion by performing the artificial rainfall test as well as physical testing. The results indicate that the risk of soil erosion can be reduced significantly by applying the coal ash which consists of more than 85% of sand to topsoil in the postmine land at the mixing ratio of over 30%. Additionally, they reveal that not only fine fractions but also microporous structures in coal ash enhance water retention capacity by retaining water in the structure, leading to the prevention of soil erosion. Thus, the risk of soil erosion can be reduced by applying coal ash to topsoil in consideration of soil composition and microporous structure of coal ash.

The potential of utilizing wood ash and peat ash on organic soils in Sweden; Arealer foer skogsgoedsling med traeaska och torvaska paa organogena jordar i Sverige

Energy Technology Data Exchange (ETDEWEB)

Haanell, Bjoern [Swedish Univ. of Agricultural Sciences, Umeaa (Sweden). Dept. of Silviculture

2004-01-01

Nutrients removed from the forest when branches and treetops are harvested as fuel can be returned to the site by recycling the remaining wood ash after combustion. This compensation measure is presently not carried out to any appreciable extent, partly because there is no economic incentive for the landowner. In sites where this measure has been applied, only on mineral soils (e.g. moraine) until now, greater margins for sustainable maintenance of the long-term site productivity can be expected. The ash contains all elements required for tree growth except for nitrogen (N). Therefore the ash amendment does not result in increased stand growth on these soils because the most important element for a growth response (N) is missing. In contrast, on organic soils N is often abundant whereas the amounts of other mineral nutrients are small. Thus, the elements lacking in the soils of peatland forests are available in the ash. This is especially true for phosphorus (P) and potassium (K). This means that peatland forests provide an opportunity for ash amendment in order to increase forest production. Old fertilization trials using wood ash show that the growth increase can be very large. The aim of this study was to (i) calculate the area of peat covered land that with respect to stand growth responses could be regarded as most suitable for bio-ash (wood ash and peat ash) fertilization, and (ii) assess the amount of bio-ash needed for fertilizing this area. Peat ash, although not as much studied, also has potential to be used to provide nutrients for increasing peatland forest growth. Most of the area calculations were based on data from the National Forest Inventory (NFI) 1997-2001. Sites were selected with guidance from existing knowledge about ash fertilization effects on tree growth and with the aid of registrations made in NFI regarding peat depth, site productivity, drainage, condition of drains, dominating field vegetation, and degree of stand development

Measurement of natural activity in peat ashes

International Nuclear Information System (INIS)

Suomela, J.

1985-01-01

High proportions of radioactive materials in peat ashes may involve radiation hazards during handling and deposition of these waste materials. Measurements have been performed to determine the content of radioactive materials in ashes from peat burning. The activities in fly ash and ''solid'' ash in seven peat-fired power plants in Sweden are presented. The methods of analysing and measuring peat ashes for activity from different radionuclides are described. The activity levels in ash samples are given

Management methods ash from combustion of biomass. Review of productions and associated methods. Extended abstract

International Nuclear Information System (INIS)

Boulday, D.; Marcovecchio, F.

2016-02-01

The study deals with the management of biomass ashes from industrial and collective facilities (wood log excluded) and provides a state of the art, in France and in Europe, flows, methods of recovery and post-treatment, physico-chemical characteristics and programs for new opportunities. Currently, flows of biomass ash are estimated at 110 kt-330 kt in France and 1 500 kt - 4 500 kt in Europe and should amount respectively 330 kt-1000 kt and 3100 kt-8000 kt in 2020. The physical and chemical composition of biomass ash is influenced by many factors: fuel, pretreatment, post-treatment, additives, fly and bottom ash, power installation, type of combustion equipment, extraction mode...However, these ashes have characteristics which are commonly accepted: liming / neutralizing power, fertilizer, pozzolanic behavior generally almost zero. In France and Europe, a distinction is made between fly and bottom ashes, usually less polluted. However, this separation does not always make sense according to the valuation mode, the type of equipment (including fluidized bed or grid) or mixtures of ash made in the plant (e.g. mix of bottom and coarse ash). Currently, the main outlet is ash landfill, followed by agricultural and forestry recycling. The other identified opportunities concern a few countries and marginal flows: brick-works, road engineering... The development of biomass energy, coupled with a reduction in landfill options, has given rise to many research and demonstration programs in recent years, particularly in France, with some promising solutions. Many limiting factors, which can be different according to opportunities, have been identified. More or less advanced solutions aimed at reducing the harmful effects of these factors (slaking lime, sorting, grinding...).However to date, the most robust and massive solution for ash recycling material remains undoubtedly the agricultural recycling. According to the study, it's necessary to consolidate the agricultural

Classification of pulverized coal ash

International Nuclear Information System (INIS)

Van der Sloot, H.A.; Van der Hoek, E.E.; De Groot, G.J.; Comans, R.N.J.

1992-09-01

The leachability of fifty different pulverized coal ashes from utilities in the Netherlands, Federal Republic of Germany and Belgium has been studied. Five different ashes were analyzed according to the complete standard leaching test and the results were published earlier. The examination of a wide variety of ashes under a wide range of pH and Liquid to Solid ratio (LS) conditions creates the possibility of identifying systematic trends in fly ash leaching behaviour and to identify the mechanisms controlling release. 16 figs., 2 tabs., 3 app., 25 refs

An improved ashing procedure for biologic sample

Energy Technology Data Exchange (ETDEWEB)

Zongmei, Wu [Zhejiang Province Enviromental Radiation Monitoring Centre (China)

1992-07-01

The classical ashing procedure in muffle was modified for biologic samples. In the modified procedure the door of muffle was open in the duration of ashing process, the ashing was accelerated and the ashing product quality was comparable to that the classical procedure. The modified procedure is suitable for ashing biologic samples in large batches.

An improved ashing procedure for biologic sample

International Nuclear Information System (INIS)

Wu Zongmei

1992-01-01

The classical ashing procedure in muffle was modified for biologic samples. In the modified procedure the door of muffle was open in the duration of ashing process, the ashing was accelerated and the ashing product quality was comparable to that the classical procedure. The modified procedure is suitable for ashing biologic samples in large batches

Treatment of fly ash for use in concrete

Science.gov (United States)

Boxley, Chett [Park City, UT

2012-05-15

A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with a quantity of spray dryer ash (SDA) and water to initiate a geopolymerization reaction and form a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 40%, and in some cases less than 20%, of the foam index of the untreated fly ash. An optional alkaline activator may be mixed with the fly ash and SDA to facilitate the geopolymerization reaction. The alkaline activator may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

Engineering properties of fly ash concrete

International Nuclear Information System (INIS)

Hilmi Mahmud

1999-01-01

This paper presents some of the engineering properties of Malaysian fly ash concrete. Workability, compressive, flexural, tensile splitting, drying shrinkage, elastic modulus and non destructive tests were performed on fly ash and control OPC concrete specimens. Data show that concrete containing 25% fly ash replacement of cement exhibit superior or similar engineering properties to that normal concrete without fly ash. These encouraging results demonstrated the technical merits of incorporating fly ash in concrete and should pave the way for wide scale use of this versatile material in the Malaysian construction industry. (author)

Treatment of fly ash for use in concrete

Science.gov (United States)

Boxley, Chett; Akash, Akash; Zhao, Qiang

2013-01-08

A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with an activator solution sufficient to initiate a geopolymerization reaction and for a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 35% of the foam index of the untreated fly ash, and in some cases less than 10% of the foam index of the untreated fly ash. The activator solution may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

Gasification of high ash, high ash fusion temperature bituminous coals

Science.gov (United States)

Liu, Guohai; Vimalchand, Pannalal; Peng, WanWang

2015-11-13

This invention relates to gasification of high ash bituminous coals that have high ash fusion temperatures. The ash content can be in 15 to 45 weight percent range and ash fusion temperatures can be in 1150.degree. C. to 1500.degree. C. range as well as in excess of 1500.degree. C. In a preferred embodiment, such coals are dealt with a two stage gasification process--a relatively low temperature primary gasification step in a circulating fluidized bed transport gasifier followed by a high temperature partial oxidation step of residual char carbon and small quantities of tar. The system to process such coals further includes an internally circulating fluidized bed to effectively cool the high temperature syngas with the aid of an inert media and without the syngas contacting the heat transfer surfaces. A cyclone downstream of the syngas cooler, operating at relatively low temperatures, effectively reduces loading to a dust filtration unit. Nearly dust- and tar-free syngas for chemicals production or power generation and with over 90%, and preferably over about 98%, overall carbon conversion can be achieved with the preferred process, apparatus and methods outlined in this invention.

The future of volcanic ash-aircraft interactions from technical and policy perspectives

Science.gov (United States)

Casadevall, T. J.; Guffanti, M.

2010-12-01

Since the advent of jet-powered flight in the 1960s, the threat of volcanic ash to aviation operations has become widely recognized and the mitigation of this threat has received concerted international attention. At the same time the susceptibility to operational disruption has grown. Technical improvements to airframes, engines, and avionic systems have been made in response to the need for improved fuel efficiency and the demand for increased capacity for passenger and freight traffic. Operational demands have resulted in the growth of extended overseas flight operations (ETOPS), increased flight frequency on air traffic routes, and closer spacing of aircraft on heavily traveled routes. The net result has been great advances in flight efficiency, but also increased susceptibility to flight disruption, especially in heavily traveled regions such as North Atlantic-Europe, North America, and the North Pacific. Advances in ash avoidance procedures, pilot and air manager training, and in detection of ash-related damage and maintenance of aircraft and engines have been spurred by noteworthy eruptions such as Galunggung, Indonesia, 1982; Redoubt, Alaska, 1989-1990; and Pinatubo, Philippines, 1991. Comparable advances have been made in the detection and tracking of volcanic ash clouds using satellite-based remote sensing and numerical trajectory forecast models. Following the April 2010 eruption of Eyjafjallajökull volcano, Iceland, the global aviation community again focused attention on the issue of safe air operations in airspace affected by volcanic ash. The enormous global disruption to air traffic in the weeks after the Eyjafjallajökull eruption has placed added emphasis for the global air traffic management system as well as on the equipment manufacturers to reevaluate air operations in ash-affected airspace. Under the leadership of the International Civil Aviation Organization and the World Meteorological Organization, efforts are being made to address this

Preparation Of Pure Carbon From Heavy Oil Fly Ash

International Nuclear Information System (INIS)

ABU ZAID, A.H.M.

2010-01-01

The Egyptian production of heavy oil is approximately 12 million tons of heavy oil per year and approximately 5.3 million tons of this amount is used as fuel in the electric power stations. Based on the fact that the ash content of Egyptian heavy oil is approximately 0.2 %, about 10600 tons of fly ash is produced per/year which causes a lot of environmental problems such as dusting, release of the acidic liquids and heavy metals such as vanadium, nickel, zinc and unburned carbon. Treatment of fly ash by leaching of vanadium and zinc was carried out under different conditions to achieve the best leaching efficiency of both vanadium and zinc by sodium hydroxide. The leaching efficiency obtained was 91% for vanadium and 98% for zinc. This study was concerned with the precipitation of zinc at pH 7.5 as zinc hydroxide and the precipitation of vanadium as ammonium metavanadate at pH 8.5. Leaching of nickel, iron and other elements from the residue was carried out by 2M HCl under different conditions. The achieved leaching efficiency of nickel was 95% where as that of iron was 92%. Precipitation efficiency of both nickel and iron were 99.9%. The residue, which contains mainly unburned carbon, have been washed two times with water and dried at 200 o C then ground to < 300μm. According to the achieved analysis of the obtained carbon, it can be characterized as pure carbon

Determining the ash content of coal flotation tailings using an MPOF optical ash meter

Energy Technology Data Exchange (ETDEWEB)

Sikora, T; Sliwa, J

1982-01-01

The block layout, a description of the design and principles of operation of an automatic optical, continuous action MPOF type ash meter are presented. The difference in the optical properties of coal and rock is used in the ash meter. The identification of the ash content is conducted on the basis of the spectral characteristics of reflection of a finely dispersed aqueous coal and rock suspension.

Determination of coal ash content by the combined x-ray fluorescence and scattering spectrum

Science.gov (United States)

Mikhailov, I. F.; Baturin, A. A.; Mikhailov, A. I.; Borisova, S. S.; Fomina, L. P.

2018-02-01

An alternative method is proposed for the determination of the inorganic constituent mass fraction (ash) in solid fuel by the ratio of Compton and Rayleigh X-ray scattering peaks IC/IR subject to the iron fluorescence intensity. An original X-ray optical scheme with a Ti/Mo (or Sc/Cu) double-layer secondary radiator allows registration of the combined fluorescence-and-scattering spectrum at the specified scattering angle. An algorithm for linear calibration of the Compton-to-Rayleigh IC/IR ratio is proposed which uses standard samples with two certified characteristics: mass fractions of ash (Ad) and iron oxide (WFe2O3). Ash mass fractions have been determined for coals of different deposits in the wide range of Ad from 9.4% to 52.7% mass and WFe2O3 from 0.3% to 4.95% mass. Due to the high penetrability of the probing radiation with energy E > 17 keV, the sample preparation procedure is rather simplified in comparison with the traditional method of Ad determination by the sum of fluorescence intensities of all constituent elements.

Mapping of Trace Elements in Coal and Ash Research Based on a Bibliometric Analysis Method Spanning 1971–2017

Directory of Open Access Journals (Sweden)

Liu Yang

2018-02-01

Full Text Available Coal is the most important fossil energy used in China. The environmental impact of trace elements released in coal combustion has become one of the hottest issues in recent years. Based on a software named CiteSpace, and social network analysis (SNA, a bibliometric analysis of research into trace elements in coal and ash field during 1971–2017 is presented with the information of authors, countries, institutions, journals, hot issues and research trends in the present study. The study results indicate that: (1 Shifeng Dai, Robert B Finkelman, Guijian Liu and James C Hower have a large number of publications with great influence. (2 China (29.8% and USA (22.2% have high productivity in total publications. China and the USA correlate closely in the cooperative web system. (3 China University of Mining and Technology and Chinese Academy of Sciences take the leading position in the quantity of publications among all research institutions. (4 Energy and fuels, engineering and environmental science are three disciplines with the most studies in this field. (5 International Journal of Coal Geology, Fuel, Energy and Fuels and Fuel Processing Technology are the top four journals with the most publications in this field. (6 The enrichment origin and modes of occurrence of trace elements are the mainstream research related to trace elements in coal and ash. The environmental problems caused by coal combustion have promoted the development of trace elements in coal research, and human health is getting more and more popular in recent years. The study findings provide a better understanding of features of trace elements in coal and ash research, which could be taken as a reference for future studies in this field.

The Outlook for Low-Grade Fuels in Tomsk Region: Research Experience at Tomsk Polytechnic University

Directory of Open Access Journals (Sweden)

Khaustov Sergei A.

2016-01-01

Full Text Available The urgency of the discussed issue is caused by the need to substitute in the regional fuel-energy balances imported energy resources with local low-grade fuels. The main aim of the study is to estimate thermal properties of local fuels in Tomsk region and evaluate its energy use viability. The methods used in the study were based standard GOST 52911-2008, 11022-95 and 6382-2001, by means of a bomb calorimeter ABK-1 and Vario micro cube analyzer. The mineral ash of researched fuels was studied agreeing with GOST 10538-87. The results state the fact that discussed low-grade fuels of Tomsk region in the unprepared form are not able to replace imported coal in regional energy balance, because of the high moisture and ash content values. A promosing direction of a low-temperature fue processing is a catalytic converter, which allows receiving hydrogen-enriched syngas from the initial solid raw.

Environmental Life Cycle Assessment of Coal-Biomass to Liquid Jet Fuel Compared to Petroleum-Derived JP-8 Jet Fuel

Science.gov (United States)

2010-03-01

is a Metal Deactivator Additive (MDA) to prevent fuel oxidation with trace metals such as copper or zinc that may be in the jet fuel (MIL- HDBK-510-1...react in the FT synthesis process). The gasifier is of the slagging type and a direct contact water quench spray system is used to cool the syngas...exiting the gasifier. The quench also removes particulate matter and contaminants not removed in the slag . However, because the ash from biomass is

Physics of fusion-fuel cycles

International Nuclear Information System (INIS)

McNally, J.R. Jr.

1981-01-01

The evaluation of nuclear fusion fuels for a magnetic fusion economy must take into account the various technological impacts of the various fusion fuel cycles as well as the relative reactivity and the required β's and temperatures necessary for economic steady-state burns. This paper will review some of the physics of the various fusion fuel cycles (D-T, catalyzed D-D, D- 3 He, D- 6 Li, and the exotic fuels: 3 He 3 He and the proton-based fuels such as P- 6 Li, P- 9 Be, and P- 11 B) including such items as: (1) tritium inventory, burnup, and recycle, (2) neutrons, (3) condensable fuels and ashes, (4) direct electrical recovery prospects, (5) fissile breeding, etc. The advantages as well as the disadvantages of the different fusion fuel cycles will be discussed. The optimum fuel cycle from an overall standpoint of viability and potential technological considerations appears to be catalyzed D-D, which could also support smaller relatively clean, lean-D, rich- 3 He satellite reactors as well as fission reactors

Electrodialytic removal of heavy metals from fly ashes

DEFF Research Database (Denmark)

Pedersen, Anne Juul

2002-01-01

The aim of the Ph.D. work was to develop the electrodialytic remediation method for removal of heavy metals from fly ashes. The work was focused on two types of fly ashes: fly ashes from wood combustion and fly ashes from municipal solid waste incineration.......The aim of the Ph.D. work was to develop the electrodialytic remediation method for removal of heavy metals from fly ashes. The work was focused on two types of fly ashes: fly ashes from wood combustion and fly ashes from municipal solid waste incineration....

Utilization options for fly ash, bottom ash, and slag in Eastern Europe

Energy Technology Data Exchange (ETDEWEB)

Manz, O.E.

1995-12-01

Since 1967, at least six ash utilization symposiums have been held in the United States, with papers presented by several European authors on the utilization of coal by-products in Eastern Europe. There is currently over 80,000 megawatts of installed coal-fired capacity available in that region. Unfortunately, of the 117,778,000 tonnes of fly ash, bottom ash, and slag produced in Eastern Europe in 1989, only 13% was utilized. This paper outlines the research and levels and kinds of coal by-product utilization taking place in Eastern Europe since the late 1960s.

Ash fusion temperatures and the transformations of coal ash particles to slag

Energy Technology Data Exchange (ETDEWEB)

Gupta, S.; Wall, T.F.; Creelman, R.A.; Gupta, R. [Univ. of Newcastle, Callaghan (Australia)

1996-12-31

A mechanistic study is detailed in which coal ash is heated with its shrinkage measured continuously up to a temperature of 1600{degrees}C. The temperatures corresponding to the rapid rate of shrinkage are shown to correspond to the formation of eutectics identified on phase diagrams. Samples were therefore heated to these temperatures, cooled rapidly and examined with an SEM to identify the associated chemical and physical changes. The progressive changes in the range of chemical analysis (from SEM), the extent of undissolved ash particles and porosity were then quantified and related to homogenization, viscosity and ash fusion mechanisms.

Ash fusion temperatures and the transformations of coal ash particles to slag

Energy Technology Data Exchange (ETDEWEB)

Wall, T.F.; Creelman, R.A.; Gupta, R.; Gupta, S. [Univ. of Newcastle (Australia)

1996-10-01

A mechanistic study is detailed in which coal ash is heated with the shrinkage and electrical resistance measured continuously up to a temperature of 1600{degrees}C. The temperatures corresponding to rapid rates of shrinkage are shown to correspond to the formation of eutectics identified on phase diagrams. Samples where therefore heated to these temperatures, cooled rapidly and examined with an SEM to identify the associated chemical and physical changes. The progressive changes in the range of chemical analysis (from SEM), the extent of undissolved ash particles and porosity are then quantified and related to the shrinkage events and standard ash fusion temperatures.

Effects of forest fuels extraction (whole tree harvesting) and ash recycling, experience and results from Swedish research

International Nuclear Information System (INIS)

Westling, Olle; Egnell, Gustaf; Dahlberg, Anders

2005-01-01

This review of Swedish research and environmental assessment studies during more than a decade is based on an ongoing synthesis of long term experiments with whole tree harvesting and wood ash recycling and other relevant research. The review is focused on effects of whole tree harvesting and compensatory fertilisation (wood ash) on forest production, biodiversity and soil and surface water. The studied extraction of biofuels (logging residues) from forest is primarily a complement to the conventional harvest of pulpwood and timber. General conclusions are that a large part of the theoretical potential of extraction of logging residues, in the form of branches and tops, can be utilised on condition that the losses of nutrients and acid neutralising capacity are compensated for through nutrient addition. To protect valuable fauna and flora, biotopes where conventional forestry is presently not applied should, with some exceptions, not be utilised for extraction of biofuels. The usage of wood ashes and other fertilisers will not increase the net accumulation of heavy metals and toxic organic elements in the forest ecosystems, on condition that the concentrations are low in the fertilisers

Application of spherical fly-ash particles to study spatial deposition of atmospheric pollutants in northen-eastern Estonia

International Nuclear Information System (INIS)

Alliksaar, T.

2000-01-01

Spherical fly-ash particles, emitted to the atmosphere in the high-temperature combustion process of fossil fuels, were found in considerable amounts in analysed snow samples of north-eastern Estonia. Spatial deposition of particles in snow cover is compared with the results of surface sediment samples of lakes. The results from snow characterise well the distribution of pollution sources and the distance from the main power plants in north eastern Estonia. Variations in particle deposition of closely situated snow samples were found to be negligible. Fly-ash particle influxes in snow samples correlate well with modelled maximum concentration fields of flyash in the near-surface air layer. (author)

Effect of Heterogeneity in Coal Ash Chemical Composition on the Onset of Conditions Favorable for Agglomeration in Fluid Beds

Directory of Open Access Journals (Sweden)

Aditi B. Khadilkar

2015-11-01

Full Text Available Ash agglomeration issues that arise due to the sticking of slag-wetted, colliding particles have been creating operational difficulties and monetary losses for the fluidized bed combustion (FBC industry. Difficulties have been experienced in the detection of slag-liquid at the low operating temperatures in fluidized bed combustors (FBCs and predicting the agglomeration behavior of fuel. This study aims to study the effect of heterogeneity in ash composition on the detection of slag-liquid in FBCs. It quantifies the slag-liquid amounts at the particle-level, under oxidizing environments, by dividing the bulk fuel into density classes. FactSage™ thermodynamic simulations of each of the particle classes, along with experimental validation of the trends with thermo-mechanical analysis (TMA and high temperature X-ray diffraction (HT-XRD were performed. The results obtained can be used to estimate the stickiness of particles in the development of ash agglomeration models based on particle collisions. The study of these particle classes shows that particle classes with specific minerals can form low temperature eutectics and lead to onset of slag-liquid formation at temperatures below those predicted by bulk analysis alone. Comparison of the differences in slag-liquid formation tendencies under reducing and oxidizing environments is also presented.

Long term effects on wet stored calcium rich fly ash with bearing on ground improvement work; Laangtidspaaverkan av kalkrika flygaskor vid vaatlagring foer anvaendning inom markstabilisering

Energy Technology Data Exchange (ETDEWEB)

Lagerlund, Johan; Jansing, Christiane

2012-02-15

Generation of electricity and heat by means of thermal power demands a product that can be ignited. This combustible material is usually coal, oil, gas, biomass and waste. If using solid fuels as coal, biomass and waste a by product known as ash is formed in the process; FA, (FA) and bottom ash. Roughly 600 Mt ashes are annually produced throughout the world and 70 weight % of these ashes are FA, 25 weight % bottom ashes and 5 weight % slag. 41 weight % of all ashes are annually reused in some form. Given the environmental impact of combustion i.e. CO{sub 2} emissions, a widened use of biomass fuels and co-combustion is expected in the near future. This will however create new problems when reusing ashes and FA in particular. The reuse of FA within the concrete industry stand for a total of about 25 % but the reuse of non-coal derived FA in the concrete industry is prohibited. Non-coal derived FA usually has higher amounts of calcium oxide, which acts expansively in concrete. Less than 20 % of biomass or co-combustion FA are reused today in Europe. A new standard, the EN 450, is however under construction. This standard will deal with the reuse of noncoal derived FA within the cement and concrete industry. In Sweden, coal is very seldom used as a fuel. More common is the use of biomass, peat and waste. It means that the FA are all non-coal derived and thus derived from reuse within the cement and concrete industry. Beside their non-coal origin, the main part of the FA is produced during November- March. This means that it might be hard to find available FA all year around, making the reuse of FA less attractive. Hence, FA must be stored prior to use. Little research have been made on the storage of calcium rich FA from biomass and co-combustion. Storing FA in a cheap way requires an addition of water to prevent from dusting when stockpiled outdoors. Addition of water in calcium rich FA will however cause an hardening of the material, thus causing detrimental

Characterization of Korean solid recovered fuels (SRFs): an analysis and comparison of SRFs.

Science.gov (United States)

Choi, Yeon-Seok; Han, Soyoung; Choi, Hang-Seok; Kim, Seock-Joon

2012-04-01

To date, Korea has used four species of solid recovered fuels (SRFs) which have been certified by the Environmental Ministry of Korea: refuse-derived fuel (RDF), refused plastic fuel (RPF), tyre-derived fuel (TDF), and wood chip fuel (WCF). These fuels have been used in many industrial boilers. In this study, seven regulatory properties associated with each of the four species: particle size, moisture and ash content, lower heating value (LHV), total chlorine, sulfur, and heavy metals content (Pb, As, Cd, Hg, Cr) were analysed. These properties are the main regulation criteria for the usage and transfer of SRFs in Korea. Different properties of each SRF were identified on the basis of data collected over the last 3 years in Korea, and the manufacturing process problem associated with the production of SRFs were considered. It was found that the high moisture content of SRFs (especially WCF) could directly lead to the low LHV of SRFs and that the poor screening and sorting of raw materials could cause defective SRF products with high ash or chlorine contents. The information obtained from this study could contribute to the manufacturing of SRF with good quality.

Hazards Associated With Recent Popocatepetl Ash Emissions

Science.gov (United States)

Nieto, A.; Martin, A.; Espinasa-Pereña, R.; Ferres, D.

2013-05-01

Popocatepetl has been producing ash from small eruptions since 1994. Until 2012 about 650 small ash emissions have been recorded at the monitoring system of Popocatépetl Volcano. Ash consists mainly of glassy lithic clasts from the recent crater domes, plagioclase and pyroxene crystals, and in major eruptions, olivine and/or hornblende. Dome forming eruptions produced a fine white ash which covers the coarser ash. This fine ash consists of plagioclase, glass and cristobalite particles mostly under15 microns. During the recent crisis at Popocatépetl, April and May2012 ash fell on villages to the east and west of the volcano, reaching Mexico City (more than 20 million people) and Puebla (2 million people). In 14 cases the plumes had heights over 2 km, the largest on May 2 and 11 (3 and 4 km in height, respectively). Heavier ash fall occurred on April 13, 14, 20, and 23 and May 2, 3, 5, 11, 14, 23, 24 and 25. A database for ash fall was constructed from April 13 with field observations, reports emitted by the Centro Nacional de Comunicaciones (CENACOM), ash fall advisories received at CENAPRED and alerts from the Servicios a la Navegación en el Espacio Aéreo Mexicano (SENEAM). This aim of this database is to calculate areas affected by the ash and estimate the ash fall volume emitted by Popocatépetl in each of these events. Heavy ash fall from the May 8 to May 11 combined with reduced visibility due to fog forced to closure of the Puebla airport during various periods of time, for up to 13 hours. Domestic and international flights were cancelled. Ash eruptions have caused respiratory conditions in the state of Puebla, to the east of the volcano, since 1994 (Rojas et al, 2001), but because of the changing wind conditions in the summer mainly, some of these ash plumes go westward to towns in the State of Mexico and even Mexico City. Preliminary analyses of these eruptions indicate that some ash emissions produced increased respiratory noninfectious problems

Utilization coke dust as fuel in the cement industry

International Nuclear Information System (INIS)

Nawaz, S.

2006-01-01

Utilization of coke dust available from coal carbonization plants, as a fuel in the cement industry has been undertaken and discussed in this research paper. The parameters studied include physical and chemical evaluation of the coke dust and its economic feasibility/ suitability as fuel for the cement plants. Detailed studies have been carried out on the above referred parameters. In addition a comparative study has been done to access its suitability in comparison to other fuels especially imported coal. It has been found that the coke dust contained about 66% fixed carbon, 29% ash, 4% volatile matter, 1% moisture and 0.48% sulphur. It gross calorific value was found to be 5292 Kcal/kg. The detailed analysis of coke dust ash was also performed to determine as to how its constituents will compare with the cement constituents. Keeping in view the experimental results/ data generated on the coke dust, it has been concluded that it can be quite a good substitute for imported coal. In doing so a substantial financial saving can be achieved which ranges 40-45%. (author)

Trace elements in co-combustion of solid recovered fuel and coal

DEFF Research Database (Denmark)

Wu, Hao; Glarborg, Peter; Jappe Frandsen, Flemming

2013-01-01

Trace element partitioning in co-combustion of a bituminous coal and a solid recovered fuel (SRF) was studied in an entrained flow reactor. The experiments were carried out at conditions similar to pulverized coal combustion, with SRF shares of 7.9 wt.% (wet basis), 14.8 wt.% and 25.0 wt.......%. In addition, the effect of additives such as NaCl, PVC, ammonium sulphate, and kaolinite on trace element partitioning was investigated. The trace elements studied were As, Cd, Cr, Pb, Sb and Zn, since these elements were significantly enriched in SRF as compared to coal. During the experiments, bottom ash...... was collected in a chamber, large fly ash particles were collected by a cyclone with a cut-off diameter of ~2.5 μm, and the remaining fly ash particles were gathered in a filter. It was found that when coal was co-fired with SRF, the As, Cd, Pb, Sb and Zn content in filter ash/cyclone ash increased almost...

Analysis list: ash2 [Chip-atlas[Archive

Lifescience Database Archive (English)

Full Text Available ash2 Larvae + dm3 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/target/ash2.1.tsv ...http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/target/ash2.5.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/target/ash2....10.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/colo/ash2.Larvae.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/colo/Larvae.gml ...

Attraction of the emerald ash borer to ash trees stressed by girdling, herbicide treatment, or wounding

Science.gov (United States)

Deborah McCullough; Therese Poland; David. Cappaert

2009-01-01

New infestations of emerald ash borer, Agrilus planipennis Fairmaire, an invasive pest native to Asia, are difficult to detect until densities build and symptoms appear on affected ash (Fraxinus spp). We compared the attraction of A. planipennis to ash trees stressed by girdling (bark and phloem removed...

Ash in fire affected ecosystems

Science.gov (United States)

Pereira, Paulo; Jordan, Antonio; Cerda, Artemi; Martin, Deborah

2015-04-01

Ash in fire affected ecosystems Ash lefts an important footprint in the ecosystems and has a key role in the immediate period after the fire (Bodi et al., 2014; Pereira et al., 2015). It is an important source of nutrients for plant recover (Pereira et al., 2014a), protects soil from erosion and controls soil hydrological process as runoff, infiltration and water repellency (Cerda and Doerr, 2008; Bodi et al., 2012, Pereira et al., 2014b). Despite the recognition of ash impact and contribution to ecosystems recuperation, it is assumed that we still have little knowledge about the implications of ash in fire affected areas. Regarding this situation we wanted to improve our knowledge in this field and understand the state of the research about fire ash around world. The special issue about "The role of ash in fire affected ecosystems" currently in publication in CATENA born from the necessity of joint efforts, identify research gaps, and discuss future cooperation in this interdisciplinary field. This is the first special issue about fire ash in the international literature. In total it will be published 10 papers focused in different aspects of the impacts of ash in fire affected ecosystems from several parts of the world: • Fire reconstruction using charcoal particles (Burjachs and Espositio, in press) • Ash slurries impact on rheological properties of Runoff (Burns and Gabet, in press) • Methods to analyse ash conductivity and sorbtivity in the laboratory and in the field (Balfour et al., in press) • Termogravimetric and hydrological properties of ash (Dlapa et al. in press) • Effects of ash cover in water infiltration (Leon et al., in press) • Impact of ash in volcanic soils (Dorta Almenar et al., in press; Escuday et al., in press) • Ash PAH and Chemical extracts (Silva et al., in press) • Microbiology (Barreiro et al., in press; Lombao et al., in press) We believe that this special issue will contribute importantly to the better understanding of

Determination of heating value of industrial waste for the formulation of alternative fuels

Directory of Open Access Journals (Sweden)

Bouabid G.

2013-09-01

Full Text Available The use of alternative fuels has become increasingly widespread. They are basically designed based on industrial waste so that they can substitute fossil fuels which start to become scarce. Alternative fuels must meet some criteria, namely an important calorific content, minimum humidity and ash content. When it comes to combustion, the most interesting parameter is the calorific value which represents the thermal energy released during combustion. The experiments that were conducted showed that the calorific value is influenced by other parameters namely moisture and ash content. It was therefore necessary to study the behavior of the heating value in terms of these two parameters in order to establish a relationship that is used to describe the behavior. This is expected to allow a simulation of the calorific value of a mixture of various industrial waste.

Viscosity of ashes from energy production and municipal solid waste handling: A comparative study between two different experimental setups

DEFF Research Database (Denmark)

Arvelakis, Stelios; Frandsen, Flemming; Folkedahl, B.

2008-01-01

This paper discusses the viscosity characteristics of ash fractions produced from the co-combustion of coal and biomass in a pilot-scale pulverized fuel (PF) boiler and from the incineration of municipal solid waste (MSW) in a Danish incinerator that were determined using the high...

Mercury and toxic metals in ash from combustion and incineration processes; Mercurio y metales toxicos en cenizas provenientes de procesos de combustion e incineracion

Energy Technology Data Exchange (ETDEWEB)

Mugica, V.; Amador, M.A.; Torres, M.; Figueroa, J. de J. [Universidad Autonomo-Metropolitana-Azcapotzalco, Reynosa (Mexico)

2003-07-01

In Mexico, most of the ashes from combustion and incineration process were not appropriately disposed, they are either left on industrial yards and cliffs or thrown away in open spaces and then carried by the wind to places where they can harm population, affect aquatic environment or soils. For prevention and control, the knowledge on the concentration of trace elements in waste ashes is necessary. In this study, several oxidation methods for digestion of ashes followed by inductively coupled plasma emission spectrometry were evaluated. Hg, Cd, Cr, Cu, Ni, Pb and V were determined in ashes from coal and fuel oil combustion, as well as in ashes from the incineration of municipal, water treatment sludge, and medical wastes. Results showed important concentrations of different trace elements in the ashes. This suggests that adequate disposal of these wastes should be mandatory. On the other hand, concentration of trace elements in the leachates indicated that these wastes are not toxic and they could be disposed in sanitary landfill. 23 refs.

CO-FIRING COAL: FEEDLOT AND LITTER BIOMASS (CFB AND CLB) FUELS IN PULVERIZED FUEL AND FIXED BED BURNERS

Energy Technology Data Exchange (ETDEWEB)

Kalyan Annamalai; John Sweeten; Saqib Mukhtar; Ben Thein; Gengsheng Wei; Soyuz Priyadarsan; Senthil Arumugam; Kevin Heflin

2003-08-28

Intensive animal feeding operations create large amounts of animal waste that must be safely disposed of in order to avoid environmental degradation. Cattle feedlots and chicken houses are two examples. In feedlots, cattle are confined to small pens and fed a high calorie grain-diet diet in preparation for slaughter. In chicken houses, thousands of chickens are kept in close proximity. In both of these operations, millions of tons of manure are produced every year. The manure could be used as a fuel by mixing it with coal in a 90:10 blend and firing it in an existing coal suspension fired combustion systems. This technique is known as co-firing, and the high temperatures produced by the coal will allow the biomass to be completely combusted. Reburn is a process where a small percentage of fuel called reburn fuel is injected above the NO{sub x} producing, conventional coal fired burners in order to reduce NO{sub x}. The manure could also be used as reburn fuel for reducing NO{sub x} in coal fired plants. An alternate approach of using animal waste is to adopt the gasification process using a fixed bed gasifier and then use the gases for firing in gas turbine combustors. In this report, the cattle manure is referred to as feedlot biomass (FB) and chicken manure as litter biomass (LB). The report generates data on FB and LB fuel characteristics. Co-firing, reburn, and gasification tests of coal, FB, LB, coal: FB blends, and coal: LB blends and modeling on cofiring, reburn systems and economics of use of FB and LB have also been conducted. The biomass fuels are higher in ash, lower in heat content, higher in moisture, and higher in nitrogen and sulfur (which can cause air pollution) compared to coal. Small-scale cofiring experiments revealed that the biomass blends can be successfully fired, and NO{sub x} emissions will be similar to or lower than pollutant emissions when firing coal. Further experiments showed that biomass is twice or more effective than coal when

Formation and utilization of fly ash

Energy Technology Data Exchange (ETDEWEB)

Vargyai, J

1974-01-01

General problems of slag and fly ash formation and utilization are discussed. The ever-increasing energy demand, and the comeback of coal as an energy carrier in power plants call for efficient solutions to the problem of slag and fly ash. Slag and fly ash are used for concrete in which they partly replace cement. Other possible uses are the amelioration of acid soils, fireclay manufacture, road construction, and tiles. It is possible to recover metals, such as vanadium, iron, aluminum, and radioactive materials from certain types of fly ash and slag. The utilization of fly ash is essential also with respect to the abatement of entrainment from dumps.