Calculation of tritium release from reactor's stack

International Nuclear Information System (INIS)

Akhadi, M.

1996-01-01

Method for calculation of tritium release from nuclear to environment has been discussed. Part of gas effluent contain tritium in form of HTO vapor released from reactor's stack was sampled using silica-gel. The silica-gel was put in the water to withdraw HTO vapor absorbed by silica-gel. Tritium concentration in the water was measured by liquid scintillation counter of Aloka LSC-703. Tritium concentration in the gas effluent and total release of tritium from reactor's stack during certain interval time were calculated using simple mathematic formula. This method has examined for calculation of tritium release from JRR-3M's stack of JAERI, Japan. From the calculation it was obtained the value of tritium release as much as 4.63 x 10 11 Bq during one month. (author)

Transient fission-product release during reactor shutdown and startup

International Nuclear Information System (INIS)

Hunt, C.E.L.; Lewis, B.J.; Dickson, L.W.

1997-12-01

Sweep-gas experiments performed at AECL's Chalk River Laboratories from 1979 to 1985 have been further analysed to determine the fraction of the gaseous fission-product inventory that is released on reactor shutdown and startup. Empirical equations were derived and applied to calculate the stable xenon release from companion fuel elements and from a well-documented experimental fuel bundle irradiated in the NRU reactor. The calculated gas release could be matched to the measured values within about a factor of two for an experimental irradiation with a burnup of 217 MWh/kgU. There was also limited information on the fraction of the radioactive iodine that was exposed, but not released, on reactor shutdown. An empirical equation is proposed for calculating this fraction. (author)

OECD Halden reactor project

International Nuclear Information System (INIS)

1979-01-01

This is the nineteenth annual Report on the OECD Halden Reactor Project, describing activities at the Project during 1978, the last year of the 1976-1978 Halden Agreement. Work continued in two main fields: test fuel irradiation and fuel research, and computer-based process supervision and control. Project research on water reactor fuel focusses on various aspects of fuel behavior under normal, and off-normal transient conditions. In 1978, participating organisations continued to submit test fuel for irradiation in the Halden boiling heavy-water reactor, in instrumented test assemblies designed and manufactured by the Project. Work included analysis of the impact of fuel design and reactor operating conditions on fuel cladding behavior. Fuel performance modelling included characterization of thermal and mechanical behavior at high burn-up, of fuel failure modes, and improvement of data qualification procedures to reduce and quantify error bands on in-reactor measurements. Instrument development yielded new or improved designs for measuring rod temperature, internal pressure, axial neutron flux shape determination, and for detecting cladding defects. Work on computer-based methods of reactor supervision and control included continued development of a system for predictive core surveillance, and of special mathematical methods for core power distribution control

Action Memorandum for the Engineering Test Reactor under the Idaho Cleanup Project

Energy Technology Data Exchange (ETDEWEB)

A. B. Culp

2007-01-26

This Action Memorandum documents the selected alternative for decommissioning of the Engineering Test Reactor at the Idaho National Laboratory under the Idaho Cleanup Project. Since the missions of the Engineering Test Reactor Complex have been completed, an engineering evaluation/cost analysis that evaluated alternatives to accomplish the decommissioning of the Engineering Test Reactor Complex was prepared adn released for public comment. The scope of this Action Memorandum is to encompass the final end state of the Complex and disposal of the Engineering Test Reactor vessol. The selected removal action includes removing and disposing of the vessel at the Idaho CERCLA Disposal Facility and demolishing the reactor building to ground surface.

Transient fission product release during reactor shutdown and startup

International Nuclear Information System (INIS)

Hunt, C.E.L.; Lewis, B.J.

1995-01-01

Sweep gas experiments performed at CRL from 1979 to 1985 have been analysed to determine the fraction of the fission product gas inventory that is released on reactor shutdown and startup. Empirical equations were derived and applied to calculate the xenon release from companion fuel elements and from a well documented experimental fuel bundle irradiated in the NRU reactor. The measured gas release could be matched to within about a factor of two for an experimental irradiation with a burnup of 217 MWh/kgU. (author)

Radionuclide release from research reactor spent fuel

Energy Technology Data Exchange (ETDEWEB)

Curtius, H., E-mail: h.curtius@fz-juelich.de [Forschungszentrum Juelich, Institut fuer Energieforschung, IEF-6 Sicherheitsforschung und Reaktortechnik, Geb. 05.3, D-52425 Juelich (Germany); Kaiser, G.; Mueller, E.; Bosbach, D. [Forschungszentrum Juelich, Institut fuer Energieforschung, IEF-6 Sicherheitsforschung und Reaktortechnik, Geb. 05.3, D-52425 Juelich (Germany)

2011-09-01

Numerous investigations with respect to LWR fuel under non oxidizing repository relevant conditions were performed. The results obtained indicate slow corrosion rates for the UO{sub 2} fuel matrix. Special fuel-types (mostly dispersed fuels, high enriched in {sup 235}U, cladded with aluminium) are used in German research reactors, whereas in German nuclear power plants, UO{sub 2}-fuel (LWR fuel, enrichment in {sup 235}U up to 5%, zircaloy as cladding) is used. Irradiated research reactor fuels contribute less than 1% to the total waste volume. In Germany, the state is responsible for fuel operation and for fuel back-end options. The institute for energy research (IEF-6) at the Research Center Juelich performs investigation with irradiated research reactor spent fuels under repository relevant conditions. In the study, the corrosion of research reactor spent fuel has been investigated in MgCl{sub 2}-rich salt brine and the radionuclide release fractions have been determined. Leaching experiments in brine with two different research reactor fuel-types were performed in a hot cell facility in order to determine the corrosion behaviour and the radionuclide release fractions. The corrosion of two dispersed research reactor fuel-types (UAl{sub x}-Al and U{sub 3}Si{sub 2}-Al) was studied in 400 mL MgCl{sub 2}-rich salt brine in the presence of Fe{sup 2+} under static and initially anoxic conditions. Within these experimental parameters, both fuel types corroded in the experimental time period of 3.5 years completely, and secondary alteration phases were formed. After complete corrosion of the used research reactor fuel samples, the inventories of Cs and Sr were quantitatively detected in solution. Solution concentrations of Am and Eu were lower than the solubility of Am(OH){sub 3}(s) and Eu(OH){sub 3}(s) solid phases respectively, and may be controlled by sorption processes. Pu concentrations may be controlled by Pu(IV) polymer species, but the presence of Pu(V) and Pu

Action Memorandum for Decommissioning the Engineering Test Reactor Complex under the Idaho Cleanup Project

International Nuclear Information System (INIS)

A. B. Culp

2007-01-01

This Action Memorandum documents the selected alternative for decommissioning of the Engineering Test Reactor at the Idaho National Laboratory under the Idaho Cleanup Project. Since the missions of the Engineering Test Reactor Complex have been completed, an engineering evaluation/cost analysis that evaluated alternatives to accomplish the decommissioning of the Engineering Test Reactor Complex was prepared and released for public comment. The scope of this Action Memorandum is to encompass the final end state of the Complex and disposal of the Engineering Test Reactor vessel. The selected removal action includes removing and disposing of the vessel at the Idaho CERCLA Disposal Facility and demolishing the reactor building to ground surface

Tritium release from lithium silicate and lithium aluminate, in-reactor and out-of-reactor

International Nuclear Information System (INIS)

Johnson, A.B. Jr.

1976-09-01

Studies were conducted to determine the generation and evolution of tritium and helium in lithium aluminate (LiAlO 2 ) and lithium silicate (Li 2 SiO 3 ) by the reaction: Li 6 + n → 4 He + T. Targets were irradiated 4.4 days in the K-West Reactor snout facility. (Silicate GVR* approximately 2.0 cc/cc; aluminate GVR approximately 1.4 cc/cc.) Gas release in-reactor was determined by post-irradiation drilling experiments on aluminum ampoules containing silicate and aluminate targets. In-reactor tritium release (at approximately 100 0 C) was found to decrease linearly with increasing target density. Tritium released in-reactor was primarily in the noncondensible form (HT and T 2 ), while in laboratory extractions (300-1300 0 C), the tritium appeared primarily in the condensible form (HTO and T 2 O). Concentrations of HT (and presumably HTO) were relatively high, indicating moisture pickup in canning operations or by inleakage of moisture after the capsule was welded. Impurities in extracted gases included H 2 O, CO 2 , CO, O 2 , H 2 , NO, SO 2 , SiF 4 and traces of hydrocarbons

Scenarios for potential radionuclide release from marine reactors dumped in the Kara Sea

International Nuclear Information System (INIS)

Lynn, N.; Mount, M.; Gussgard, K.

1995-01-01

The largest inventory of radioactive materials dumped in the Kara Sea by the former Soviet Union comes from the spent nuclear fuel (SNF) of seven marine reactors, the current (1994) inventory of which makes a total of approximately 4.7x10 15 Bq. In progressing its work for the International Arctic Seas Assessment Project, under the auspices of the International Atomic Energy Agency, the Source Term Working Group has analysed the Source Term and subsequently developed a number of model scenarios for the potential release patterns of radionuclides into the Kara Sea from the SNF and activated components dumped within the marine reactors.These models are based on the present and future conditions of the barrier materials and their configuration within the dumped objects. They account for progressive corrosion of the outer and inner steel barriers, breakdown of the organic fillers, and degradation and leaching from the SNFs. Annual release rates are predicted to four thousand years into the future. 5 refs., 1 fig., 1 tab

Application of Emergency Action Levels from Potential Release at Research Reactor HANARO

International Nuclear Information System (INIS)

Kim, Jongsoo; Lee, Goan Yub; Lee, Hae Choi; Kim, Bong Suk

2014-01-01

Execution of the protective action promptly is possible that Emergency Action Levels (EALs) must be established for a radiological release from nuclear facility. The EALs for electric power reactor are already developed and applied to recognize an emergency situation rapidly. Recently the IAEA published the safety report including the EALs for research reactor. This paper describes the EALs to apply for a potential release pathway at the research reactor HANARO. The results of table 1 and 2 will be higher than actual because the weather condition in real situation is difference. However, the EALs applying the potential stack release, ground release and site can be useful for research reactor HANARO making the emergency declaration. The EALs at the site boundary of the table 3 can be applied to protect the off-site public

Reactor vessel decommissioning project. Final report

International Nuclear Information System (INIS)

Schoonen, D.H.

1984-09-01

This report describes a reactor vessel decommissioning project; it documents and explains the project objectives, scope, performance results, and sodium removal process. The project was successfully completed in FY-1983, within budget and without significant problems or adverse impact on the environment. Waste generated by the operation included the reactor vessel, drained sodium, and liquid, solid, and gaseous wastes which were significantly less than project estimates. Personnel radiation exposures were minimized, such that the project total was one-half the predicted exposure level. Except for the sodium removed, the material remaining in the reactor vessel is essentially the same as when the vessel arrived for processing

Research reactor job analysis - A project description

International Nuclear Information System (INIS)

Yoder, John; Bessler, Nancy J.

1988-01-01

Addressing the need of the improved training in nuclear industry, nuclear utilities established training program guidelines based on Performance-Based Training (PBT) concepts. The comparison of commercial nuclear power facilities with research and test reactors owned by the U.S. Department of Energy (DOE), made in an independent review of personnel selection, training, and qualification requirements for DOE-owned reactors pointed out that the complexity of the most critical tasks in research reactors is less than that in power reactors. The U.S. Department of Energy (DOE) started a project by commissioning Oak Ridge Associated Universities (ORAU) to conduct a job analysis survey of representative research reactor facilities. The output of the project consists of two publications: Volume 1 - Research Reactor Job Analysis: Overview, which contains an Introduction, Project Description, Project Methodology,, and. An Overview of Performance-Based Training (PBT); and Volume 2 - Research Reactor Job Analysis: Implementation, which contains Guidelines for Application of Preliminary Task Lists and Preliminary Task Lists for Reactor Operators and Supervisory Reactor Operators

Fission product release from SLOWPOKE-2 reactors

Energy Technology Data Exchange (ETDEWEB)

Harnden-Gillis, A M.C. [Queen` s Univ., Kingston, ON (Canada). Dept. of Physics

1994-12-31

Increasing radiation fields at several SLOWPOKE-2 reactors fuelled with highly enriched uranium aluminum alloy fuel have begun to interfere with the daily operation of these reactors. To investigate this phenomenon, samples of reactor container water and gas from the headspace were obtained at four SLOWPOKE-2 reactor facilities and examined by gamma ray spectroscopy methods. These radiation fields are due to the circulation of fission products within the reactor container vessel. The most likely source of the fission product release is an area of uranium-bearing material exposed to the coolant at the end weld line which originated at the time of fuel fabrication. The results of this study are compared with observations from an underwater visual examination of one core and the metallographic examination of archived fuel elements. 19 refs., 4 tabs., 8 figs.

Tritium release from lithium silicate and lithium aluminate, in-reactor and out-of-reactor

Energy Technology Data Exchange (ETDEWEB)

Johnson, A.B. Jr.

1976-09-01

Studies were conducted to determine the generation and evolution of tritium and helium in lithium aluminate (LiAlO/sub 2/) and lithium silicate (Li/sub 2/SiO/sub 3/) by the reaction: Li/sup 6/ + n ..-->.. /sup 4/He + T. Targets were irradiated 4.4 days in the K-West Reactor snout facility. (Silicate GVR* approximately 2.0 cc/cc; aluminate GVR approximately 1.4 cc/cc.) Gas release in-reactor was determined by post-irradiation drilling experiments on aluminum ampoules containing silicate and aluminate targets. In-reactor tritium release (at approximately 100/sup 0/C) was found to decrease linearly with increasing target density. Tritium released in-reactor was primarily in the noncondensible form (HT and T/sub 2/), while in laboratory extractions (300-1300/sup 0/C), the tritium appeared primarily in the condensible form (HTO and T/sub 2/O). Concentrations of HT (and presumably HTO) were relatively high, indicating moisture pickup in canning operations or by inleakage of moisture after the capsule was welded. Impurities in extracted gases included H/sub 2/O, CO/sub 2/, CO, O/sub 2/, H/sub 2/, NO, SO/sub 2/, SiF/sub 4/ and traces of hydrocarbons.

Decommissioning of the ASTRA research reactor - planning, executing and summarizing the project

International Nuclear Information System (INIS)

Meyer, F.

2010-01-01

The decommissioning of the ASTRA research reactor at the Austrian Research Centres Seibersdorf was described within three technical papers already released in Nuclear Technology and Radiation Protection throughout the years 2003, 2006, and 2008. Following a suggestion from IAEA the project was investigated well after the files were closed regarding rather administrative than technical matters starting with the project mission, explaining the project structure and identifying the key factors and the key performance indicators. The continuous documentary and reporting system as implemented to fulfil the informational needs of stakeholders, management, and project staff alike is described. Finally the project is summarized in relationship to the performance indicators. (author)

Hydrogeological and Groundwater Flow Model for C, K, L, and P Reactor Areas, Savannah River Site, Aiken, South Carolina

International Nuclear Information System (INIS)

Flach, G.P.

1999-01-01

A regional groundwater flow model encompassing approximately 100 mi 2 surrounding the C, K. L. and P reactor areas has been developed. The Reactor flow model is designed to meet the planning objectives outlined in the General Groundwater Strategy for Reactor Area Projects by providing a common framework for analyzing groundwater flow, contaminant migration and remedial alternatives within the Reactor Projects team of the Environmental Restoration Department

Role of fission gas release in reactor licensing

International Nuclear Information System (INIS)

1975-11-01

The release of fission gases from oxide pellets to the fuel rod internal voidage (gap) is reviewed with regard to the required safety analysis in reactor licensing. Significant analyzed effects are described, prominent gas release models are reviewed, and various methods used in the licensing process are summarized. The report thus serves as a guide to a large body of literature including company reports and government documents. A discussion of the state of the art of gas release analysis is presented

Hydrogeological and Groundwater Flow Model for C, K, L, and P Reactor Areas, Savannah River Site, Aiken, South Carolina

Energy Technology Data Exchange (ETDEWEB)

Flach, G.P.

1999-02-24

A regional groundwater flow model encompassing approximately 100 mi{sup 2} surrounding the C, K. L. and P reactor areas has been developed. The Reactor flow model is designed to meet the planning objectives outlined in the General Groundwater Strategy for Reactor Area Projects by providing a common framework for analyzing groundwater flow, contaminant migration and remedial alternatives within the Reactor Projects team of the Environmental Restoration Department.

Summary of estimated doses and risks resulting from routine radionuclide releases from fast breeder reactor fuel cycle facilities

International Nuclear Information System (INIS)

Miller, C.W.; Meyer, H.R.

1985-01-01

A project is underway at Oak Ridge National Laboratory to assess the human health and environment effects associated with operation of Liquid Metal Fast Breeder Reactor fuel cycle. In this first phase of the work, emphasis was focused on routine radionuclide releases from reactor and reprocessing facilities. For this study, sites for fifty 1-GW(e) capacity reactors and three reprocessing plants were selected to develop scenarios representative of US power requirements. For both the reactor and reprocessing facility siting schemes selected, relatively small impacts were calculated for locality-specific populations residing within 100 km. Also, the results of these analyses are being used in the identification of research priorities. 13 refs., 2 figs., 3 tabs

The Maple reactor project

International Nuclear Information System (INIS)

Malkoske, G.R.; Labrie, J.-P.

2003-01-01

MDS Nordion supplies the majority of the world's reactor-produced medical isotopes. These isotopes are currently produced in the NRU reactor at AECL's Chalk River Laboratories (CRL). Medical isotopes and related technology are relied upon around the world to prevent, diagnose and treat disease. The NRU reactor, which has played a key role in supplying medical isotopes to date, has been in operation for over 40 years. Replacing this aging reactor has been a priority for MDS Nordion to assure the global nuclear medicine community that Canada will continue to be a dependable supplier of medical isotopes. MDS Nordion contracted AECL to construct two MAPLE reactors dedicated to the production of medical isotopes. The MDS Nordion Medical Isotope Reactor (MMIR) project started in September 1996. This paper describes the MAPLE reactors that AECL has built at its CRL site, and will operate for MDS Nordion. (author)

Experiment calculated ascertainment of factors affecting the energy release in IGR reactor core

International Nuclear Information System (INIS)

Kurpesheva, A.M.; Zhotabayev, Zh.R.

2006-01-01

Full text: At present energy supply resources problem is important. Nuclear reactors can, of course, solve this problem, but at the same time there is another issue, concerning safety exploitation of nuclear reactors. That is why, for the last seven years, such experiments as 'Investigation of the processes, conducting severe accidents with core melting' are being carried out at our IGR (impulse graphite reactor) reactor. Leaving out other difficulties of such experiments, it is necessary to notice, that such experiments require more accurate IGR core energy release calculations. The final aim of the present research is verification and correction of the existing method or creation of new method of IGR core energy release calculation. IGR reactor is unique and there is no the same reactor in the world. Therefore, application of the other research reactor methods here is quite useful. This work is based on evaluation of factors affecting core energy release (physical weight of experimental device, different configuration of reactor core, i.e. location of absorbers, initial temperature of core, etc), as well as interference of absorbers group. As it is known, energy release is a value of integral reactor power. During experiments with rays, Reactor power depends on currents of ion production chambers (IPC), located round the core. It is worth to notice that each ion production chamber (IPC) in the same start-up has its own ratio coefficient between IPC current and reactor present power. This task is complicated due to 'IPC current - reactor power' ratio coefficients, that change continuously, probably, because of new loading of experimental facility and different position of control rods. That is why, in order to try about reactor power, before every start-up, we have to re-determine the 'IPC current - reactor power' ratio coefficients for each ion production chamber (IPC). Therefore, the present work will investigate the behavior of ratio coefficient within the

Status of the RA research reactor decommissioning project

International Nuclear Information System (INIS)

Ljubenov, V.; Nikolic, D.; Pesic, M.; Milosevic, M.; Kostic, Lj.; Steljic, M.; Sotic, O.; Antic, D. . E-mail address of corresponding author: vladan@vin.bg.ac.yu; Ljubenov, V.)

2005-01-01

The 6.5 MW heavy water RA research reactor at the VINCA Institute of Nuclear Sciences operated from 1959 to 1984. After 18 years of extended shutdown in 2002 it was decided that the reactor shutdown should be final. Preliminary decommissioning activities have been initiated by the end of 2002 under the Technical Co-operation Programme of the International Atomic Energy Agency. The objective of the project is to implement safe, timely and cost-effective decommissioning of the RA reactor up to unrestricted use of the site. Decommissioning project is closely related to two other projects: Safe Removal of the RA Reactor Spent Nuclear Fuel and Radioactive Waste Management in VINCA Institute. The main phases of the project include preparation of the detailed decommissioning plan, radiological characterization of the reactor site, dismantling and removal of the reactor components and structures, decontamination, final radiological site survey and the documentation of all the activities in order to obtain the approval for unrestricted use of the facility site. In this paper a review of the activities related to the preparation and realization of the RA reactor decommissioning project is given. Status of the project's organizational and technical aspects as for July 2004 are presented and plans for the forthcoming phases of the project realization are outlined. (author)

Parametric study of the Ignalina reactor building capability as barrier against accidental releases of radioactivity

International Nuclear Information System (INIS)

Blomquist, R.; Johansson, Kjell; Nilsson, Lars.

1993-01-01

The results of a parametric study are offered to the Ignalina plant management staff and to the Lithuanian and Swedish nuclear inspectorates as a basis for a decision whether there is mutual interest in a project for the purpose of strengthening the Ignalina reactor buildings inherent capabilities to provide a barrier against accidental releases of radioactivity. Practical measures to consider are: * establish natural convection of warm air from the steam drums to the tall stack of 150 m height. * reduce the resulting draught of air through the reactor hall floor between the fuel channel shield blocks into the steam drum compartments. * apply filtration to the stack air flow. 18 refs

Decontamination and decommissioning project status of the TRIGA mark-2±3 research reactors

International Nuclear Information System (INIS)

Jung, K. J.; Baek, S. T.; Jung, W. S.; Park, S. K.; Jung, K. H.

1999-01-01

TRIGA Mark-II, the first research reactor in Korea, has operated since 1962, and the second one, TRIGA Mark-III since 1972. Both of them had their operation phased out in 1995 due to their lives and operation of the new research reactor, HANARO at the Korea Atomic Energy Research Institute (KAERI) in Taejeon. Decontamination and decommissioning (D and D) project of the TRIGA Mark-II and Mark-III was started in January 1997 and will be completed in December 2002. In the first year of the project, work was performed in preparation of the decommissioning plan, start of the environmental impact assessment and setup licensing procedure and documentation for the project with cooperation of Korea Institute of Nuclear Safety (KINS). In 1998, Hyundai Engineering Company (HEC) is the main contractor to do design and licensing documentation for the D and D of both reactors. British Nuclear Fuels plc (BNFL) is technical assisting partner of HEC. The decommissioning plan document was submitted to the Ministry of Science and Technology (MOST) for the decommissioning license in December 1998, and it expecting to be issued a license at the end of September 1999. The goal of this project is to release the reactor site and buildings as an unrestricted area. This paper summarizes current status and future plan for the D and D project

Project management plan for the 105-C Reactor interim safe storage project. Revision 1

International Nuclear Information System (INIS)

Miller, R.L.

1997-01-01

In 1942, the Hanford Site was commissioned by the US Government to produce plutonium. Between 1942 and 1955, eight water-cooled, graphite-moderated reactors were constructed along the Columbia River at the Hanford Site to support the production of plutonium. The reactors were deactivated from 1964 to 1971 and declared surplus. The Surplus Production Reactor Decommissioning Project (BHI 1994b) will decommission these reactors and has selected the 105-C Reactor to be used as a demonstration project for interim safe storage at the present location and final disposition of the entire reactor core in the 200 West Area. This project will result in lower costs, accelerated schedules, reduced worker exposure, and provide direct benefit to the US Department of Energy for decommissioning projects complex wide. This project sets forth plans, organizational responsibilities, control systems, and procedures to manage the execution of the Project Management Plan for the 105-C Reactor Interim Safe Storage Project (Project Management Plan) activities to meet programmatic requirements within authorized funding and approved schedules. The Project Management Plan is organized following the guidelines provided by US Department of Energy Order 4700.1, Project Management System and the Richland Environmental Restoration Project Plan (DOE-RL 1992b)

Reports on BMBF-sponsored research projects in the field of reactor safety. Reporting period 1 July - 31 December 1995

International Nuclear Information System (INIS)

1996-01-01

The Gesellschaft fuer Anlagen- und Reaktorsicherheit informs of the status of LWR tasks and projects on the safety of advanced reactors. Each progress report represents a compilation of individual reports about objectives, the work performed, the results, and the next steps of the works. The individual reports of quality assurance, safety of reactor component, emergency core cooling, lors of coolant, meltdown, fission product release, risk and reliability, are classified according to projects to the reactor safety research program. Another table uses the same classification system as applied in the nuclear safety index of the CEC. (DG)

Individual dose due to radioactivity accidental release from fusion reactor

Energy Technology Data Exchange (ETDEWEB)

Nie, Baojie [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); University of Science and Technology of China, Hefei, Anhui, 230027 (China); Ni, Muyi, E-mail: muyi.ni@fds.org.cn [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); Wei, Shiping [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); University of Science and Technology of China, Hefei, Anhui, 230027 (China)

2017-04-05

Highlights: • Conservative early dose of different unit fusion radioactivity release were assessed. • Data of accident level in INES for fusion reactor were proposed. • Method of environmental restoration time after fusion accident was proposed. • The maximum possible accident level for ITER like fusion reactor is 6. • We need 34–52 years to live after the fusion hypothetical accident. - Abstract: As an important index shaping the design of fusion safety system, evaluation of public radiation consequences have risen as a hot topic on the way to develop fusion energy. In this work, the comprehensive public early dose was evaluated due to unit gram tritium (HT/HTO), activated dust, activated corrosion products (ACPs) and activated gases accidental release from ITER like fusion reactor. Meanwhile, considering that we cannot completely eliminate the occurrence likelihood of multi-failure of vacuum vessel and tokamak building, we conservatively evaluated the public radiation consequences and environment restoration after the worst hypothetical accident preliminarily. The comparison results show early dose of different unit radioactivity release under different conditions. After further performing the radiation consequences, we find it possible that the hypothetical accident for ITER like fusion reactor would result in a level 6 accident according to INES, not appear level 7 like Chernobyl or Fukushima accidents. And from the point of environment restoration, we need at least 69 years for case 1 (1 kg HTO and 1000 kg dust release) and 34–52 years for case 2 (1 kg HTO and 10kg–100 kg dust release) to wait the contaminated zone drop below the general public safety limit (1mSv per year) before it is suitable for human habitation.

Fission product release from TRIGA-LEU reactor fuels

International Nuclear Information System (INIS)

Baldwin, N.L.; Foushee, F.C.; Greenwood, J.S.

1980-01-01

Due to present international concerns over nuclear proliferation, TRIGA reactor fuels will utilize only low-enriched uranium (LEU) (enrichment <20%). This requires increased total uranium loading per unit volume of fuel in order to maintain the appropriate fissile loading. Tests were conducted to determine the fractional release of gaseous and metallic fission products from typical uranium-zirconium hydride TRIGA fuels containing up to 45 wt-% uranium. These tests, performed in late 1977 and early 1978, were similar to those conducted earlier on TRIGA fuels with 8.5 wt-% U. Fission gas release measurements were made on prototypic specimens from room temperature to 1100 deg. C in the TRIGA King Furnace Facility. The fuel specimens were irradiated in the TRIGA reactor at a low power level. The fractional releases of the gaseous nuclides of krypton and xenon were measured under steady-state operating conditions. Clean helium was used to sweep the fission gases released during irradiation from the furnace into a standard gas collection trap for gamma counting. The results of these tests on TRIGA-LEU fuel agree well with data from the similar, earlier tests on TRIGA fuel. The correlation used to calculate the release of fission products from 8.5 wt-% U TRIGA fuel applies equally well for U contents up to 45 wt-%. (author)

Alternatives to L startup: new production reactor

International Nuclear Information System (INIS)

Hostetler, D.E.

1983-01-01

An alternative to renewed operation of L Reactor for increased production of nuclear materials would be the construction and operation of a New Production Reactor (NPR). This report describes a conceptual design for a low temperature heavy water reactor with no electricity generation (LTHWR-NE) to be built as a new production reactor at the Savannah River Plant (SRP). The reactor design is based on the proven SRP reactor design with enhancements and state-of-the-art equipment. Aluminum cladding temperatures would be the same as with current operations. The power and productivity of the new reactor would be greater than L Reactor by about 30%. However, the estimated time from authorization to startup is 10 years. Thus an NPR could not contribute to material production until late 1993 at the earliest

Generation IV reactors: international projects

International Nuclear Information System (INIS)

Carre, F.; Fiorini, G.L.; Kupitz, J.; Depisch, F.; Hittner, D.

2003-01-01

Generation IV international forum (GIF) was initiated in 2000 by DOE (American department of energy) in order to promote nuclear energy in a long term view (2030). GIF has selected 6 concepts of reactors: 1) VHTR (very high temperature reactor system, 2) GHR (gas-cooled fast reactor system), 3) SFR (sodium-cooled fast reactor system, 4) SCWR (super-critical water-cooled reactor system), 5) LFR (lead-cooled fast reactor system), and 6) MFR (molten-salt reactor system). All these 6 reactor systems have been selected on criteria based on: - a better contribution to sustainable development (through their aptitude to produce hydrogen or other clean fuels, or to have a high energy conversion ratio...) - economic profitability, - safety and reliability, and - proliferation resistance. The 6 concepts of reactors are examined in the first article, the second article presents an overview of the results of the international project on innovative nuclear reactors and fuel cycles (INPRO) within IAEA. The project finished its first phase, called phase-IA. It has produced an outlook into the future role of nuclear energy and defined the need for innovation. The third article is dedicated to 2 international cooperations: MICANET and HTR-TN. The purpose of MICANET is to propose to the European Commission a research and development strategy in order to develop the assets of nuclear energy for the future. Future reactors are expected to be more multiple-purposes, more adaptable, safer than today, all these developments require funded and coordinated research programs. The aim of HTR-TN cooperation is to promote high temperature reactor systems, to develop them in a long term perspective and to define their limits in terms of burn-up and operating temperature. (A.C.)

An experimental investigation of fission product release in SLOWPOKE-2 reactors - Data report

International Nuclear Information System (INIS)

Harnden, A.M.C.

1995-09-01

The results of an investigation into the release of fission products from SLOWPOKE-2 reactors fuelled with a highly-enriched uranium alloy core are detailed in Volume 1. This data report (Volume 2) contains plots of the activity concentrations of the fission products observed in the reactor container at the University of Toronto, Ecole Polytechnique and the Kanata Isotope Production Facility. Release rates from the reactor container water to the gas headspace are also included. (author)

Media and Australia's replacement reactor project

International Nuclear Information System (INIS)

Keenan, Pamela

2001-01-01

In September 1997, the Commonwealth Government of Australia announced a proposal to build a replacement nuclear research reactor at Lucas Heights in Sydney. Extensive public consultation, parliamentary debate and independent reports were prepared to ensure that the new facility would meet strict international requirements, national safety and environmental standards, and performance specifications servicing the needs of Australia - for decades to come. On 6 June 2000, Argentine company INVAP SE was announced as the preferred tenderer. In July 2000 contracts were signed between INVAP and the Australian Nuclear Science and Technology Organisation for the construction the replacement reactor, due to be completed in 2005. In order to retain a strong local presence, INVAP undertook a joint venture with two of Australia's foremost heavy construction businesses. Briefly the new research reactor will be a replacement for the ageing Australian Reactor (HIFAR). Nuclear science and technology, in Australia, is no stranger to media controversy and misinformation. Understandably the announcement of a preferred tenderer followed by the signing of contracts, attracted significant national and international media attention. However in the minds of the media, the issue is far from resolved and is now a constant 'news story' in the Australian media. Baseless media stories have made claims that the project will cost double the original estimates; question the credibility of the contractors; and raise issues of international security. The project is currently linked with Australia's requirements for long term nuclear waste management and there has been an attempt to bring national Indigenous People's issues into play. Some of these issues have been profiled in the press internationally. So, just to set the record straight and give you an appropriate impression of what's 'really happening' I would like to highlight a few issues, how ANSTO dealt with these, and what was finally reported

Specialists' meeting on fission product release and transport in gas-cooled reactors. Summary report

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-07-01

The purpose of the Meeting on Fission Product Release and Transport in Gas-Cooled Reactors was to compare and discuss experimental and theoretical results of fission product behaviour in gas-cooled reactors under normal and accidental conditions and to give direction for future development. The technical part of the meeting covered operational experience and laboratory research, activity release, and behaviour of released activity.

Specialists' meeting on fission product release and transport in gas-cooled reactors. Summary report

International Nuclear Information System (INIS)

1985-01-01

The purpose of the Meeting on Fission Product Release and Transport in Gas-Cooled Reactors was to compare and discuss experimental and theoretical results of fission product behaviour in gas-cooled reactors under normal and accidental conditions and to give direction for future development. The technical part of the meeting covered operational experience and laboratory research, activity release, and behaviour of released activity

Reactor-specific spent fuel discharge projections, 1987-2020

International Nuclear Information System (INIS)

Walling, R.C.; Heeb, C.M.; Purcell, W.L.

1988-03-01

The creation of five reactor-specific spent fuel data bases that contain information on the projected amounts of spent fuel to be discharged from U.S. commercial nuclear reactors through the year 2020 is described. The data bases contain detailed spent fuel information from existing, planned, and projected pressurized water reactors (PWR) and boiling water eactors (BWR), and one existing high temperature gas reactor (HTGR). The projections are based on individual reactor information supplied by the U.S. reactor owners. The basic information is adjusted to conform to Energy Information Administration (EIA) forecasts for nuclear installed capacity, generation, and spent fuel discharged. The EIA cases considered are: No New Orders (assumes increasing burnup), No New Orders with No Increased Burnup, Upper Reference (assumes increasing burnup), Upper Reference with No Increased Burnup, and Lower Reference (assumes increasing burnup). Detailed, by-reactor tables are provided for annual discharged amounts of spent fuel, for storage requirements assuming maximum at-reactor storage, and for storage requirements assuming maximum at-reactor storage plus intra-utility transshipment of spent fuel. 8 refs., 8 figs., 10 tabs

ADVANTAGES, DISADVANTAGES, AND LESSONS LEARNED FROM MULTI-REACTOR DECOMMISSIONING PROJECTS

International Nuclear Information System (INIS)

Morton, M.R.; Nielson, R.R.; Trevino, R.A.

2003-01-01

This paper discusses the Reactor Interim Safe Storage (ISS) Project within the decommissioning projects at the Hanford Site and reviews the lessons learned from performing four large reactor decommissioning projects sequentially. The advantages and disadvantages of this multi-reactor decommissioning project are highlighted

Prometheus Project Reactor Module Final Report, For Naval Reactors Information

International Nuclear Information System (INIS)

MJ Wollman; MJ Zika

2006-01-01

The Naval Reactors Prime Contractor Team (NRPCT) led the development of a power plant for a civilian nuclear electric propulsion (NEP) system concept as part of the Prometheus Project. This report provides a summary of the facts, technical insights, and programmatic perspectives gained from this two-year program. The Prometheus Project experience has been extensively documented to better position the US for future space reactor development. Major Technological and engineering challenges exist to develop a system that provides useful electric power from a nuclear fission heat source operating in deep space. General issues include meeting mission requirements in a system that has a mass low enough to launch from earth while assuring public safety and remaining safely shutdown during credible launch accidents. These challenges may be overcome in the future if there is a space mission with a compelling need for nuclear power to drive development. Past experience and notional mission requirements indicate that any useful space reactor system will be unlike past space reactors and existing terrestrial reactors

OECD Halden reactor project

International Nuclear Information System (INIS)

1978-01-01

This report summarizes the activities of the OECD Halden Reactor Project for the year 1976. The main items reported on are: a) the process supervision and control which have focused on core monitoring and control, and operator-process communication; b) the fuel performance and safety behavior which have provided data and analytical descriptions of the thermal, mechanical and chemical behavior of fuel under various operating conditions; c) the reactor operations and d) the administration and finance

New Production Reactor project-management plan

International Nuclear Information System (INIS)

McCrosson, F.J.; Hibbard, L.; Buckner, M.R.

1982-01-01

This document provides a project management plan for the first phase of a project to design and build a new production reactor (NPR) at SRP. The design of the NPR is based upon proven SRP heavy water reactor design, with several enhancements such as full containment, moderator detritiation, improved cooling, and modernized control rooms and instrumentation. The first phase of the NPR project includes environmental and safety analyses, preparation of the technical data summary and basic data, site studies, engineering studies, and conceptual design. The project management plan was developed by a 14-member task force comprised of representatives from the Technical Division, the Manufacturing Division, the Departmental Engineer's Office, and the Engineering Department

Reactor-specific spent fuel discharge projections: 1985 to 2020

International Nuclear Information System (INIS)

Heeb, C.M.; Libby, R.A.; Walling, R.C.; Purcell, W.L.

1986-09-01

The creation of four spent-fuel data bases that contain information on the projected amounts of spent fuel to be discharged from US commercial nuclear reactors through the year 2020 is described. The data bases contain detailed spent-fuel information from existing, planned, and projected pressurized water reactors (PWR) and boiling water reactors (BWR). The projections are based on individual reactor information supplied by the US reactor owners. The basic information is adjusted to conform to Energy Information Agency (EIA) forecasts for nuclear installed capacity, generation, and spent fuel discharged. The EIA cases considered are: (1) No New Orders with Extended Burnup, (2) No New Orders with Constant Burnup, (3) Middle Case with Extended Burnup, and (4) Middle Case with Constant Burnup. Detailed, by-reactor tables are provided for annual discharged amounts of spent fuel, for storage requirements assuming maximum-at-reactor storage, and for storage requirements assuming maximum-at-reactor plus intra-utility transshipment of spent fuel

Release from control of inactive material from decommissioning the ASTRA research reactor

International Nuclear Information System (INIS)

Brandl, A.; Hrnecek, E.; Steger, F.; Kurz, H.; Meyer, F.; Karacson, P.

2003-01-01

The Austrian Research Centers Seibersdorf have been operating a 10 MW ASTRA research reactor from 1960 until 1999. After that date, a submission of the intention to decommission the reactor has been provided to the Competent Authorities. After completion of an Environmental Impact Study by the Competent Authorities and modification of the Permissions for Site Use, the reactor finally entered the decommissioning phase in 2003. Inactive materials from the decommissioning site are expected to be released from control. The procedure for such a release from control agreed upon between the Competent Authorities and ARC Seibersdorf involves a four-step measurement, verification, and certification process detailed in this paper. By September 2003, this four-step procedure has been completed for 16500 kg of steel re-enforced concrete and for 5500 kg of other materials; the release from control of 3000 kg of paraffin and 10000 kg of graphite from the thermal column are planned for the near future. (author)

Radiological release analysis for the EFR project

International Nuclear Information System (INIS)

Carluec, B.; Dechelette, S.; Balard, F.

1996-01-01

Tile safety approach of the European Fast Reactor project (EFR) requires to deal with certain hypothetical CDA and therefore to enhance the containment structure in order to mitigate the consequences. The analyses are performed in order to design a containment taking advantages of die inherent characteristics of the liquid metal fast reactor. Adequate computer codes describing the sequences which follow the core disruptive accident, are used. One of the main tool is the computer code CONTAIN-LMR. The goal of these analyses is to identify the most sensitive phenomena such as the overpressure due to sodium fire, to assess the involvement of some design parameters such as the leaktightness of the structures, the arrangement of the ventilation system- the effects of the implementation of filters or a retention chamber. The results of the calculations allow to propose a robust containment for EFR, and to verify that the radiological releases in the environment can be limited. The paper presents the safety approach of EFR adopted with regard to the accidents leading to a radiological source term, and the main design options retained for the containment of EFR. Then, the methods used to describe the phenomena and some representative calculations, will be presented. The main useful information and knowledge which derive from these studies for the designers conclude the paper. (author)

Reactor-specific spent fuel discharge projections: 1986 to 2020

International Nuclear Information System (INIS)

Heeb, C.M.; Walling, R.C.; Purcell, W.L.

1987-03-01

The creation of five reactor-specific spent fuel data bases that contain information on the projected amounts of spent fuel to be discharged from US commercial nuclear reactors through the year 2020 is described. The data bases contain detailed spent-fuel information from existing, planned, and projected pressurized water reactors (PWR) and boiling water reactors (BWR). The projections are based on individual reactor information supplied by the US reactor owners. The basic information is adjusted to conform to Energy Information Agency (EIA) forecasts for nuclear installed capacity, generation, and spent fuel discharged. The EIA cases considered are: (1) No new orders with extended burnup, (2) No new orders with constant burnup, (3) Upper reference (which assumes extended burnup), (4) Upper reference with constant burnup, and (5) Lower reference (which assumes extended burnup). Detailed, by-reactor tables are provided for annual discharged amounts of spent fuel, for storage requirements assuming maximum-at-reactor storage, and for storage requirements assuming maximum-at-reactor plus intra-utility transshipment of spent fuel. 6 refs., 8 figs., 8 tabs

ASAMPSA2 best-practices guidelines for L2 PSA development and applications. Volume 3 - Extension to Gen IV reactors

International Nuclear Information System (INIS)

Bassi, C.; Bonneville, H.; Brinkman, H.; Burgazzi, L.; Polidoro, F.; Vincon, L.; Jouve, S.

2010-01-01

The main objective assigned to the Work Package 4 (WP4) of the 'ASAMPSA2' project (EC 7. FPRD) consist in the verification of the potential compliance of L2PSA guidelines based on PWR/BWR reactors (which are specific tasks of WP2 and WP3) with Generation IV representative concepts. Therefore, in order to exhibit potential discrepancies between LWRs and new reactor types, the following work was based on the up-to-date designs of: - The European Fast Reactor (EFR) which will be considered as prototypical of a pool-type Sodium-cooled Fast Reactor (SFR); - The ELSY design for the Lead-cooled Fast Reactor (LFR) technology; - The ANTARES project which could be representative of a Very-High Temperature Reactor (VHTR); - The CEA 2400 MWth Gas-cooled Fast Reactor (GFR). (authors)

Light water reactor safety research project

International Nuclear Information System (INIS)

Markoczy, G.; Aksan, S.N.; Behringer, K.; Prodan, M.; Stierli, F.; Ullrich, G.

1980-07-01

The research and development activities for the safety of Light Water Power Reactors carried out 1979 at the Swiss Federal Institute for Reactor Research are described. Considerations concerning the necessity, objectives and size of the Safety Research Project are presented, followed by a detailed discussion of the activities in the five tasks of the program, covering fracture mechanics and nondestructive testing, thermal-hydraulics, reactor noise analysis and pressure vessel steel surveillance. (Auth.)

Australia's replacement research reactor project

International Nuclear Information System (INIS)

Harris, K.J.

1999-01-01

the technical and contractual requirements of the project. A project manager with extensive experience in major defence projects has been contracted and a team of technical and contracts specialists has now completed documentation which has been issued as a Request for Tender to four pre-qualified reactor vendors. The four vendors were selected as a result of a worldwide invitation in mid 1998 for expressions of interest. The tender process is a 'two envelope' system whereby the tenderers are required to submit in one envelope the technical and contractual details of their bid whilst submitting the pricing details in the other envelope. Tenders close on 3 January 2000. A contract is expected to be agreed by mid 2000 with commissioning completed during 2005

Release of low-contaminated reactor wastes for unrestricted use

International Nuclear Information System (INIS)

Carleson, G.

1982-01-01

A generic methodology has been used to evaluate the dose contributions to an individual and to the population of five categories of low-contaminated reactor wastes produced according to the Swedish program and released for unrestricted handling and use. A reference quantity with a surface dose rate below a predetermined level is followed along the whole commercial pathway from the reactor station to the final product consumer and/or a municipal waste station. Dose contributions are calculated for each step in a normal pathway under maximally unfavourable conditions. (Auth.)

Regional groundwater flow model for C, K. L. and P reactor areas, Savannah River Site, Aiken, SC

Energy Technology Data Exchange (ETDEWEB)

Flach, G.P.

2000-02-11

A regional groundwater flow model encompassing approximately 100 mi2 surrounding the C, K, L, and P reactor areas has been developed. The reactor flow model is designed to meet the planning objectives outlined in the General Groundwater Strategy for Reactor Area Projects by providing a common framework for analyzing groundwater flow, contaminant migration and remedial alternatives within the Reactor Projects team of the Environmental Restoration Department. The model provides a quantitative understanding of groundwater flow on a regional scale within the near surface aquifers and deeper semi-confined to confined aquifers. The model incorporates historical and current field characterization data up through Spring 1999. Model preprocessing is automated so that future updates and modifications can be performed quickly and efficiently. The CKLP regional reactor model can be used to guide characterization, perform scoping analyses of contaminant transport, and serve as a common base for subsequent finer-scale transport and remedial/feasibility models for each reactor area.

Regional groundwater flow model for C, K. L. and P reactor areas, Savannah River Site, Aiken, SC

International Nuclear Information System (INIS)

Flach, G.P.

2000-01-01

A regional groundwater flow model encompassing approximately 100 mi2 surrounding the C, K, L, and P reactor areas has been developed. The reactor flow model is designed to meet the planning objectives outlined in the General Groundwater Strategy for Reactor Area Projects by providing a common framework for analyzing groundwater flow, contaminant migration and remedial alternatives within the Reactor Projects team of the Environmental Restoration Department. The model provides a quantitative understanding of groundwater flow on a regional scale within the near surface aquifers and deeper semi-confined to confined aquifers. The model incorporates historical and current field characterization data up through Spring 1999. Model preprocessing is automated so that future updates and modifications can be performed quickly and efficiently. The CKLP regional reactor model can be used to guide characterization, perform scoping analyses of contaminant transport, and serve as a common base for subsequent finer-scale transport and remedial/feasibility models for each reactor area

Data for FUMEX: Results from fuel behavior studies at the OECD Halden Reactor Project for model validation and development

International Nuclear Information System (INIS)

Wiesenack, W.

1997-01-01

Investigations of phenomena associated with extended or high burn-up are an important part of the fuel and materials testing programme carried out at the OECD Halden Reactor Project. The in-core studies comprise long term fuel rod behavior as well as the response to power ramps. Performance is assessed through measurements of fuel centre temperature, rod pressure, elongation of cladding and fuel stack, and cladding diameter changes obtained during full power reactor operation. Data from fuel behavior studies at the OECD Halden Reactor Project, provided for the IAEA co-ordinated research programme FUMEX, are used to elucidate short and long-term developments of fuel behavior. The examples comprise: fuel conductivity degradation manifested as a gradual temperature increase with burn-up; the influence of a combination of small gap/high fission gas release on fuel centre temperature (situation at high burn-up); fission gas release during normal operation and power ramps, and the possibility of a burn-up enhancement; PCMI reflected by cladding elongation, also for the case of a nominally open gap, and the change of interaction onset with burn-up. (author). 10 refs, 9 figs, 1 tab

Data for FUMEX: Results from fuel behavior studies at the OECD Halden Reactor Project for model validation and development

Energy Technology Data Exchange (ETDEWEB)

Wiesenack, W [Institutt for Energiteknikk, Halden (Norway). OECD Halden Reaktor Projekt

1997-08-01

Investigations of phenomena associated with extended or high burn-up are an important part of the fuel and materials testing programme carried out at the OECD Halden Reactor Project. The in-core studies comprise long term fuel rod behavior as well as the response to power ramps. Performance is assessed through measurements of fuel centre temperature, rod pressure, elongation of cladding and fuel stack, and cladding diameter changes obtained during full power reactor operation. Data from fuel behavior studies at the OECD Halden Reactor Project, provided for the IAEA co-ordinated research programme FUMEX, are used to elucidate short and long-term developments of fuel behavior. The examples comprise: fuel conductivity degradation manifested as a gradual temperature increase with burn-up; the influence of a combination of small gap/high fission gas release on fuel centre temperature (situation at high burn-up); fission gas release during normal operation and power ramps, and the possibility of a burn-up enhancement; PCMI reflected by cladding elongation, also for the case of a nominally open gap, and the change of interaction onset with burn-up. (author). 10 refs, 9 figs, 1 tab.

Research of heat releasing element of an active zone of gaseous nuclear reactor with pumped through nuclear fuel - uranium hexafluoride (UF6)

International Nuclear Information System (INIS)

Batyrbekov, G.; Batyrbekov, E.; Belyakova, E.; Kunakov, S.; Koltyshev, S.

1996-01-01

The purpose of the offered project is learning physics and substantiation of possibility of creation gaseous nuclear reactor with pumped through nuclear fuel-hexafluoride of uranium (Uf6).Main problems of this work are'. Determination of physic-chemical, spectral and optical properties of non-equilibrium nuclear - excited plasma of hexafluoride of uranium and its mixtures with other gases. Research of gas dynamics of laminar, non-mixing two-layer current of gases of hexafluoride of uranium and helium at availability and absence of internal energy release in hexafluoride of uranium with the purpose to determinate a possibility of isolation of hexafluoride of uranium from walls by inert helium. Creation and research of gaseous heat releasing element with pumped through fuel Uf6 in an active zone of research nuclear WWR-K reactor. Objects of a research: Non-equilibrium nuclear - excited plasma of hexafluoride of uranium and its mixtures with other gases. With use of specially created ampoules will come true in-reactor probe and spectral diagnostics of plasma. Calculations of kinetics with the account of main elementary processes proceeding in it, will be carried out. Two-layer non-mixed streams of hexafluoride of uranium and helium at availability and absence of internal energy release. Conditions of obtaining and characteristics of such streams will be investigated. Gaseous heat releasing element with pumped through fuel - Uf6 in an active zone of nuclear WWR-K reactor

A sustainability analysis of the Brazilian multipurpose reactor project

International Nuclear Information System (INIS)

Obadia, I.J.; Perrotta, J.A.

2010-01-01

The project of a new research reactor in Brazil for radioisotope production, support of the nuclear energy program and scientific research has received a positive sign of the government and is starting to be developed by the Brazilian Commission of Nuclear Energy. International Atomic Energy Agency points out that the implementation of a new research reactor is a major undertaking for a country, requiring an analysis to identify to which extent the conditions of the national nuclear program are proper and adequate to lead to a sustainable research reactor life cycle. This paper introduces the Brazilian Multipurpose Reactor Project (RMB) and describes the sustainability analysis performed, which has shown that the national nuclear infrastructure presents a very favourable condition to the implementation of the RMB project as well as to provide a sustainable life cycle for this new research reactor. (author)

Derived release limits for airborne effluents at TRIGA - INR Reactor

International Nuclear Information System (INIS)

Toma, A.; Dulama, C.; Hirica, O.; Mihai, S.; Oprea, I.

2008-01-01

Beginning from fulfilling the purposes of dose limitation system recommended by ICRP, and now accepted in radiation protection, this paper presents an environmental transfer model to calculate derived release limits for airborne and gaseous radioactive effluents at TRIGA-INR, 14 MW Steady State Reactor, in function on INR-Pitesti site. The methodology consists in determination of the principal exposure pathways for different groups of population and dose calculations for each radionuclide. The characterization of radionuclides transfer to environment was made using the compartmental model. The parameter transfer concept was used to describe the distribution of radionuclides between the different compartments. Atmospheric dispersion was very carefully treated, because it is the primary mechanism of the transfer of radionuclides in the environment and it determines all exposure pathways. Calculation of the atmospheric dispersion was made using ORION-II computer code based on the Gaussian plume model which takes account of site's specific climate and relief conditions. Default values recommended by literature were used to calculate some of the parameters when specific site values were not available. After identification of all transfer parameters which characterize the most important exposure pathways, the release rate corresponding to the individual dose rate limit was calculated. This maximum release rate is the derived release limit for each radionuclide and source. In the paper, the derived release limits are calculated for noble gases, radioiodine and other airborne particulate radionuclides, which can be released on the TRIGA-INR reactor stack, and are important to radiation protection. (authors)

The Jules Horowitz Reactor project, a driver for revival of the research reactor community

International Nuclear Information System (INIS)

Pere, P.; Cavailler, C.; Pascal, C.

2010-01-01

The first concrete of the nuclear island for the Jules Horowitz Reactor (JHR) was poured at the end of July 2009 and construction is ongoing. The JHR is the largest new platform for irradiation experiments supporting Generation II and III reactors, Generation IV technologies, and radioisotope production. This facility, composed of a unique grouping of workshops, hot cells and hot laboratories together with a first-rate MTR research reactor, will ensure that the process, from preparations for irradiation experiments through post-irradiation non-destructive examination, is completed expediently, efficiently and, of course, safely. In addition to the performance requirements to be met in terms of neutron fluxes on the samples (5x10 14 n.cm -2 /sec -1 E>1 MeV in core and 3,6x10 14 n.cm -2 /sec -1 E<0.625 eV in the reflector) and the JHR's considerable irradiation capabilities (more than 20 experiments and one-tenth of irradiation area for simultaneous radioisotope production), the JHR is the first MTR to be built since the end of the 1960s, making this an especially challenging project. The presentation will provide an overview of the reactor, hot cells and laboratories and an outline of the key milestones in the project schedule, including initial criticality in early 2014 and radioisotope production in 2015. This will be followed by a description of the project organization set up by the CEA as owner and future operator and AREVA TA as prime contractor and supplier of critical systems, and a discussion of project challenges, especially those dealing with the following items:accommodation of a broad experimental domain; involvement by international partners making in-kind contributions to the project; ? development of components critical to safety and performance; the revival of engineering of research reactors and experimental devices involving France's historical players in the field of research reactors, and; tools to carry out the project, including computer codes

The international thermonuclear reactor project

International Nuclear Information System (INIS)

James, T.R.

1993-01-01

The International Thermonuclear Experimental Reactor Project is a 6-year collaborative effort involving the U.S., Europe, Japan, and the Russian Federation to produce a detailed engineering design for the next-step fusion device

Halden reactor project

International Nuclear Information System (INIS)

1980-01-01

The research programme at the Halden Project is focused on the following three areas: 1. In-core behavior of reactor fuel, particularly reliability and safety aspects, which is studied through irradiation of test fuel elements. 2. Prediction, surveillance and control of fuel and core performance for which models of fuel and core behavior are developed. 3. Applications of process computers to power plant control, for which prototype software systems and hardware arrangements are developed

Windscale advanced gas-cooled reactor (WAGR) decommissioning project overview

International Nuclear Information System (INIS)

Pattinson, A.

2003-01-01

The current BNFL reactor decommissioning projects are presented. The projects concern power reactor sites at Berkely, Trawsfynydd, Hunterstone, Bradwell, Hinkley Point; UKAEA Windscale Pile 1; Research reactors within UK Scottish Universities at East Kilbride and ICI (both complete); WAGR. The BNFL environmental role include contract management; effective dismantling strategy development; implementation and operation; sentencing, encapsulation and transportation of waste. In addition for the own sites it includes strategy development; baseline decommissioning planning; site management and regulator interface. The project objectives for the Windscale Advanced Gas-Cooled Reactor (WAGR) are 1) Safe and efficient decommissioning; 2) Building of good relationships with customer; 3) Completion of reactor decommissioning in 2005. The completed WAGR decommissioning campaigns are: Operational Waste; Hot Box; Loop Tubes; Neutron Shield; Graphite Core and Restrain System; Thermal Shield. The current campaign is Lower Structures and the remaining are: Pressure vessel and Insulation; Thermal Columns and Outer Vault Membrane. An overview of each campaign is presented

Light Water Reactor Sustainability Constellation Pilot Project FY11 Summary Report

International Nuclear Information System (INIS)

Johansen, R.

2011-01-01

Summary report for Fiscal Year 2011 activities associated with the Constellation Pilot Project. The project is a joint effor between Constellation Nuclear Energy Group (CENG), EPRI, and the DOE Light Water Reactor Sustainability Program. The project utilizes two CENG reactor stations: R.E. Ginna and Nine Point Unit 1. Included in the report are activities associate with reactor internals and concrete containments.

Regulatory Technology Development Plan - Sodium Fast Reactor. Mechanistic Source Term - Metal Fuel Radionuclide Release

International Nuclear Information System (INIS)

Grabaskas, David; Bucknor, Matthew; Jerden, James

2016-01-01

The development of an accurate and defensible mechanistic source term will be vital for the future licensing efforts of metal fuel, pool-type sodium fast reactors. To assist in the creation of a comprehensive mechanistic source term, the current effort sought to estimate the release fraction of radionuclides from metal fuel pins to the primary sodium coolant during fuel pin failures at a variety of temperature conditions. These release estimates were based on the findings of an extensive literature search, which reviewed past experimentation and reactor fuel damage accidents. Data sources for each radionuclide of interest were reviewed to establish release fractions, along with possible release dependencies, and the corresponding uncertainty levels. Although the current knowledge base is substantial, and radionuclide release fractions were established for the elements deemed important for the determination of offsite consequences following a reactor accident, gaps were found pertaining to several radionuclides. First, there is uncertainty regarding the transport behavior of several radionuclides (iodine, barium, strontium, tellurium, and europium) during metal fuel irradiation to high burnup levels. The migration of these radionuclides within the fuel matrix and bond sodium region can greatly affect their release during pin failure incidents. Post-irradiation examination of existing high burnup metal fuel can likely resolve this knowledge gap. Second, data regarding the radionuclide release from molten high burnup metal fuel in sodium is sparse, which makes the assessment of radionuclide release from fuel melting accidents at high fuel burnup levels difficult. This gap could be addressed through fuel melting experimentation with samples from the existing high burnup metal fuel inventory.

Regulatory Technology Development Plan - Sodium Fast Reactor. Mechanistic Source Term - Metal Fuel Radionuclide Release

Energy Technology Data Exchange (ETDEWEB)

Grabaskas, David [Argonne National Lab. (ANL), Argonne, IL (United States); Bucknor, Matthew [Argonne National Lab. (ANL), Argonne, IL (United States); Jerden, James [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-02-01

The development of an accurate and defensible mechanistic source term will be vital for the future licensing efforts of metal fuel, pool-type sodium fast reactors. To assist in the creation of a comprehensive mechanistic source term, the current effort sought to estimate the release fraction of radionuclides from metal fuel pins to the primary sodium coolant during fuel pin failures at a variety of temperature conditions. These release estimates were based on the findings of an extensive literature search, which reviewed past experimentation and reactor fuel damage accidents. Data sources for each radionuclide of interest were reviewed to establish release fractions, along with possible release dependencies, and the corresponding uncertainty levels. Although the current knowledge base is substantial, and radionuclide release fractions were established for the elements deemed important for the determination of offsite consequences following a reactor accident, gaps were found pertaining to several radionuclides. First, there is uncertainty regarding the transport behavior of several radionuclides (iodine, barium, strontium, tellurium, and europium) during metal fuel irradiation to high burnup levels. The migration of these radionuclides within the fuel matrix and bond sodium region can greatly affect their release during pin failure incidents. Post-irradiation examination of existing high burnup metal fuel can likely resolve this knowledge gap. Second, data regarding the radionuclide release from molten high burnup metal fuel in sodium is sparse, which makes the assessment of radionuclide release from fuel melting accidents at high fuel burnup levels difficult. This gap could be addressed through fuel melting experimentation with samples from the existing high burnup metal fuel inventory.

Frequency limitations on reactor release derived from radiological criteria

International Nuclear Information System (INIS)

Clarke, R.H.

1976-05-01

Acceptable frequencies are suggested with which a number of defined individual and collective dose criteria are met. This has enabled a relationship to be proposed between the frequency and any event leading to release of radioactive material and the dose commitment to the hypothetical individual at the site boundary. The philosphy developed is generally applicable, but in this instance it has been demonstrated for an SGHW Reactor located at Sizewell. The results are derived on the basis of an acceptable level of risk of fatality to the most exposed individual and the application of the methodology to other reactor types and sites is demonstrated. (author)

The Jules Horowitz reactor project, a driver for revival of the research reactor community

Energy Technology Data Exchange (ETDEWEB)

Pere, P.; Cavailler, C.; Pascal, C. [AREVA TA, CEA Cadarache - Etablissement d' AREVA TA - Chantier RJH - MOE - BV2 - BP no. 9 - 13115 Saint Paul lez Durance (France); CS 50497 - 1100, rue JR Gauthier de la Lauziere, 13593 Aix en Provence cedex 3 (France)

2010-07-01

The first concrete of the nuclear island for the Jules Horowitz Reactor (JHR) was poured at the end of July 2009 and construction is ongoing. The JHR is the largest new platform for irradiation experiments supporting Generation II and III reactors, Generation IV technologies, and radioisotope production. This facility, composed of a unique grouping of workshops, hot cells and hot laboratories together with a first -rate MTR research reactor, will ensure that the process, from preparations for irradiation experiments through post-irradiation non-destructive examination, is completed expediently, efficiently and, of course, safely. In addition to the performance requirements to be met in terms of neutron fluxes on the samples (5x10{sup 14} n.cm{sup -2}/sec{sup -1} E> 1 MeV in core and 3,6x10{sup 14} n.cm{sup -2}/sec{sup -1} E<0.625 eV in the reflector) and the JHR's considerable irradiation capabilities (more than 20 experiments and one-tenth of irradiation area for simultaneous radioisotope production), the JHR is the first MTR to be built since the end of the 1960's, making this an especially challenging project. The presentation will provide an overview of the reactor, hot cells and laboratories and an outline of the key milestones in the project schedule, including initial criticality in early 2014 and radioisotope production in 2015. This will be followed by a description of the project organization set up by the CEA as owner and future operator and AREVA TA as prime contractor and supplier of critical systems, and a discussion of project challenges, especially those dealing with the following items: - accommodation of a broad experimental domain, - involvement by international partners making in-kind contributions to the project, - development of components critical to safety and performance, - the revival of engineering of research reactors and experimental devices involving France's historical players in the field of research reactors, and

Evaluation of the Steel Creek ecosystem in relation to the proposed restart of L reactor

International Nuclear Information System (INIS)

Smith, M.H.; Sharitz, R.R.; Gladden, J.B.

1981-10-01

Information is presented on the following subjects: habitat and vegetation, the avifauna, semi-aquatic and terrestrial vertebrates, and aquatic communities of Steel Creek, species of special concern, and radiocesium in Steel Creek. Two main goals of the study were the compilation of a current inventory of the flora and fauna of the Steel Creek ecosystem and an assessment of the probable impacts of radionuclides, primarily 137 Cs, that were released into Steel Creek during earlier reactor operations. Although a thorough evaluation of the impacts of the L reactor restart is impossible at this time, it is concluded that the effects on the Steel Creek ecosystem will be substantial if no mitigative measures are taken

Dynamic evaluation of environmental impact due to tritium accidental release from the fusion reactor

International Nuclear Information System (INIS)

Nie, Baojie; Ni, Muyi; Jiang, Jieqiong; Wu, Yican

2015-01-01

As one of the key safety issues of fusion reactors, tritium environmental impact of fusion accidents has attracted great attention. In this work, the dynamic tritium concentrations in the air and human body were evaluated on the time scale based on accidental release scenarios under the extreme environmental conditions. The radiation dose through various exposure pathways was assessed to find out the potential relationships among them. Based on this work, the limits of HT and HTO release amount for arbitrary accidents were proposed for the fusion reactor according to dose limit of ITER. The dynamic results aim to give practical guidance for establishment of fusion emergency standard and design of fusion tritium system. - Highlights: • Dynamic tritium concentration in the air and human body evaluated on the time scale. • Different intake forms and relevant radiation dose assessed to find out the potential relationships. • HT and HTO release amount limits for arbitrary accidents proposed for the fusion reactor according to dose limit

An initial assessment of the Chernobyl-4 reactor accident release source

International Nuclear Information System (INIS)

Macdonald, H.F.; ApSimon, H.M.; Wilson, J.J.N.

1986-07-01

The long-range atmospheric dispersion model MESOS has been used to provide a preliminary evaluation of the effects over Western Europe of radioactivity released during the accident which occurred at the Chernobyl-4 reactor in the USSR in April 1986. The results of this analysis have been compared with observations during the first week or so following the accident of airborne contamination levels at a range of locations across Europe in order to obtain an estimate of accident release source. The work presented here was performed during the 6-8 weeks following the accident and the results obtained will be subject to refinement as more detailed data become available. However, at this early stage they indicate a release source for the Chernobyl accident, expressed as a fraction of the estimated reactor core inventory, of approx. 15-20% of the iodine and caesium isotopes, approx. 1% of the ruthenium and lesser amounts of the other fission products and actinides, together with an implied major fraction of the krypton and xenon noble gases. (author)

Halden Reactor Project Workshop: Understanding Advanced Instrumentation and Controls Issues

International Nuclear Information System (INIS)

Beltracchi, L.

1991-01-01

A Halden Reactor Project Workshop on 'Understanding Advanced Instrumentation and Controls Issues' was held in Halden, Norway, during June 17-18, 1991. The objectives of the workshop were to (1) identify and prioritize the types of technical information that the Halden Project can produce to facilitate the development of man-machine interface guidelines and (2) to identify methods to effectively integrate and disseminate this information to signatory organizations. As a member of the Halden Reactor Project, the Nuclear Regulatory Commission (NRC) requested the workshop. This request resulted from the NRC's need for human factors guidelines for the evaluation of advanced instrumentation and controls. The Halden Reactor Project is a cooperative agreement among several countries belonging to the Organization for Economic Cooperation and Development (OECD). The US began its association with the Halden Project in 1958 through the Atomic Energy Commission. The project's activities are centered at the Halden heavy-water reactor and its associated man-machine laboratory in Halden, Norway. The research program conducted at Halden consists of studies on fuel performance and computer-based man-machine interfaces

LOFC fission product release and circulating activity calculations for gas-cooled reactors

International Nuclear Information System (INIS)

Apperson, C.E. Jr.; Carruthers, L.M.; Lee, C.E.

1977-01-01

The inventories of fission products in a gas-cooled reactor under accident and normal steady state conditions are time and temperature dependent. To obtain a reasonable estimate of these inventories it is necessary to consider fuel failure, a temperature dependent variable, and radioactive decay, a time dependent variable. Using arbitrary radioactive decay chains and published fuel failure models for the High Temperature Gas-Cooled Reactor (HTGR), methods have been developed to evaluate the release of fission products during the Loss of Forced Circulation (LOFC) accident and the circulating and plateout fission product inventories during steady state non-accident operation. The LARC-2 model presented here neglects the time delays in the release from the HTGR due to diffusion of fission products from particles in the fuel rod through the graphite matrix. It also neglects the adsorption and evaporation process of metallics at the fuel rod-graphite and graphite-coolant hole interfaces. Any time delay due to the finite time of transport of fission products by convection through the coolant to the outside of the prestressed concrete reactor vessel (PCRV) is also neglected. This model assumes that all fission products released from fuel particles are immediately deposited outside the PCRV with no time delay

MANHATTAN PROJECT B REACTOR HANFORD WASHINGTON [HANFORD'S HISTORIC B REACTOR (12-PAGE BOOKLET)

Energy Technology Data Exchange (ETDEWEB)

GERBER MS

2009-04-28

The Hanford Site began as part of the United States Manhattan Project to research, test and build atomic weapons during World War II. The original 670-square mile Hanford Site, then known as the Hanford Engineer Works, was the last of three top-secret sites constructed in order to produce enriched uranium and plutonium for the world's first nuclear weapons. B Reactor, located about 45 miles northwest of Richland, Washington, is the world's first full-scale nuclear reactor. Not only was B Reactor a first-of-a-kind engineering structure, it was built and fully functional in just 11 months. Eventually, the shoreline of the Columbia River in southeastern Washington State held nine nuclear reactors at the height of Hanford's nuclear defense production during the Cold War era. The B Reactor was shut down in 1968. During the 1980's, the U.S. Department of Energy began removing B Reactor's support facilities. The reactor building, the river pumphouse and the reactor stack are the only facilities that remain. Today, the U.S. Department of Energy (DOE) Richland Operations Office offers escorted public access to B Reactor along a designated tour route. The National Park Service (NPS) is studying preservation and interpretation options for sites associated with the Manhattan Project. A draft is expected in summer 2009. A final report will recommend whether the B Reactor, along with other Manhattan Project facilities, should be preserved, and if so, what roles the DOE, the NPS and community partners will play in preservation and public education. In August 2008, the DOE announced plans to open B Reactor for additional public tours. Potential hazards still exist within the building. However, the approved tour route is safe for visitors and workers. DOE may open additional areas once it can assure public safety by mitigating hazards.

The 'Reacteur Jules Horowitz': a new experimental reactor project

International Nuclear Information System (INIS)

Frachet, S.; Ballagny, A.

1999-01-01

The Jules Horowitz Reactor (RJH) is a new research reactor project dedicated to materials and nuclear fuel testing, the location of which is foreseen at the CEA-CADARACHE site, and the start-up in 2006. The launching of this project originated from a double finding: The development of nuclear power plants aimed at satisfying the energy needs of the next century, cannot be envisaged without experimental reactors which are unrivaled for the validation of new concepts of nuclear fuels, materials, and components as well as for their qualification under irradiation. The existing experimental reactors are 30 to 40 years old and it is advisable to examine henceforth the necessity for and the nature of a new reactor to take over and replace, at the beginning of next century, the reactors shut-down in the mean time or at the very end of their lives. Within this framework, the CEA has undertaken, in the last years, a study on the mid and long term irradiation needs, to determine the main features and performances of this new reactor. The concept of the reactor will have to fulfill the thermal neutron irradiation requirements as well as the fast neutron experimental needs, with a great potential versatility for any new irradiation programs. The reactor project selected among several different concepts, is finally a light water pool concept, with 100 MW thermal power. It could reach neutronic fluxes twice those of present French reactors, and allows for many irradiations in and around the core, under high neutron fluxes. The reactor will satisfy the highest level of safety in full accordance with international safety recommendations and the French safety approach for this kind of nuclear facility, thus giving an added safety margin keeping in mind the versatility of research reactors. The feasibility studies have been focused on the following most important items: neutronic and thermalhydraulic studies on alternative core designs, with or without added pressurization

The environmental impact of radioactive releases from accidents in nuclear power reactors

International Nuclear Information System (INIS)

Beattie, J.R.; Griffiths, R.F.; Kaiser, G.D.; Kinchin, G.H.

1978-01-01

A survey of accidental releases of radioactivity from thermal and fast reactors is presented. Following a general discussion on the hazards involved, the nature of the environmental impact of radioactive releases is examined. This includes a brief review of the natural radiation background, the effect on human health of various levels of radiation and radioactivity, permissible and reference levels, and the type of hazards from both passing clouds of airbourne radioactive material and from ground deposited material. The problem of atmospheric dispersion and methods of calculations of radioactive materials in the atmosphere are examined in order for the consequences of accidental release to be analysed. National accidents and their environmental consequences are then examined. Finally there is a review of the risks to which man is always exposed because of his environment. Common and collective risks are also considered. Conclusions are reached as to the acceptibility or otherwise of the environmental impact of reactor accidents. (U.K.)

Probabilistic evaluation of main coolant pipe break indirectly induced by earthquakes Savannah River Project L and P Reactors

International Nuclear Information System (INIS)

Short, S.A.; Wesley, D.A.; Awadalla, N.G.; Kennedy, R.P.

1989-01-01

A probabilistic evaluation of seismically-induced indirect pipe break for the Savannah River Project (SRP) L- and P-Reactor main coolant (process water) piping has been conducted. Seismically-induced indirect pipe break can result primarily from: (1) failure of the anchorage of one or more of the components to which the pipe is anchored; or (2) failure of the pipe due to collapse of the structure. the potential for both types of seismically-induced indirect failures was identified during a seismic walkdown of the main coolant piping. This work involved: (1) identifying components or structures whose failure could result in pipe failure; (2) developing seismic capacities or fragilities of these components; (3) combining component fragilities to develop plant damage state fragilities; and (4) convolving the plant seismic fragilities with a probabilistic seismic hazard estimate for the site in order to obtain estimates of seismic risk in terms of annual probability of seismic-induced indirect pipe break

Technical modifications and management innovations in exporting nuclear reactor projects

International Nuclear Information System (INIS)

Mao Xiaoming; Qin Xijiu; Ding Hu; Xue Zhaoqun; Wen Shengjun

2009-01-01

As a main channel for the foreign economic cooperation of China nuclear industry, China Zhongyuan Engineering Corporation (CZEC) has been constantly engaged in technical modifications and management innovations in its exporting nuclear reactor projects. In the implementation of heavy water research reactor contract in Algeria, CZEC had established a complete and adequate design standards system in compliance with the international standards, and made significant modifications to the reference reactor in the aspects of reactor power and reactor safety, solved quite some technical issues which-affected the reactor technical performance. The modifications and improvements enabled the technical parameters, safety features, reactor multipurpose application to attain to the advanced level in the world. In the 300 MWe PWR NPPs in Pakistan, safety features had been updated in line with upgrading regulatory requisites. The design philosophy and technology application demonstrated CZEC' s creation and innovation on basis of constant safety enhancement of nuclear power projects. Efforts had also been made by CZEC' s creation and innovation on basis of constant safety enhancement of nuclear power projects. Efforts had also been made by CZEC in promoting China made equipment items and components exportation. (authors)

Radiation shielding provided by residential houses in Japan in reactor accidents accompanied with atmospheric release

International Nuclear Information System (INIS)

Yamaguchi, Yasuhiro; Minami, Kentaro

1991-01-01

The present report describes the radiation shielding effect of houses in Japan against the radioactive cloud resulting from a major reactor accident accompanied with atmospheric release. The shielding factor of houses, the ratio of indoor exposure rate to outdoor one, has been studied for the semi-infinite and finite clouds which contain γ-emitting radionuclides released from a reactor facility. The shielding factor of houses against γ-rays from the radioactive cloud decreases gradually with release delay time and keeps a minimum during the period from 50 to 1000 hours after reactor shutdown while 133 Xe predominates in the cloud. Radioiodines mixed in the cloud raise slightly the shielding factor, and the factor depends little on the shape of the cloud. A set of shielding factors for the use of emergency planning was consequently proposed as 0.4 for simple ferroconcrete residential house and 0.9 for other ordinary ones. (author)

An experimental investigation of fission product release in SLOWPOKE-2 reactors

International Nuclear Information System (INIS)

Harnden, A.M.C.

1995-09-01

Increasing radiation fields due to a release of fission products in the reactor container of several SLOWPOKE-2 reactors fuelled with a highly-enriched uranium (HEU) alloy core have been observed. It is believed that these increases are associated with the fuel fabrication where a small amount of uranium-bearing material is exposed to the coolant at the end-welds of the fuel element. To investigate this phenomenon samples of reactor water and gas from the headspace above the water have been obtained and examined by gamma spectrometry methods for reactors of various burnups at the University of Toronto, Ecole Polytechnique and Kanata Isotope Production Facility. An underwater visual examination of the fuel core at Ecole Polytechnique has also provided information on the condition of the core. This report (Volume 1) summarizes the equipment, analysis techniques and results of tests conducted at the various reactor sites. The data report is published as Volume 2. (author). 30 refs., 9 tabs., 20 figs

Experience with effluent release from the Omaha V. A. Hospital TRIGA reactor

Energy Technology Data Exchange (ETDEWEB)

Blotcky, A J [Veterans Administration Hospital (United States)

1974-07-01

The effluent release from experiments is controlled by limiting the size of each sample irradiated so that if it was accidentally completely volatized into the closed room, the radioactive concentration would not exceed the permitted limits. The possible releases of Ar-41 and N-16 from the reactor are also considered. The experimentally determined levels of radiation around the Omaha facility are shown. From the data and calculations it was concluded that the levels of effluent release from the Omaha TRIGA are very small.

Experience with effluent release from the Omaha V. A. Hospital TRIGA reactor

International Nuclear Information System (INIS)

Blotcky, A.J.

1974-01-01

The effluent release from experiments is controlled by limiting the size of each sample irradiated so that if it was accidentally completely volatized into the closed room, the radioactive concentration would not exceed the permitted limits. The possible releases of Ar-41 and N-16 from the reactor are also considered. The experimentally determined levels of radiation around the Omaha facility are shown. From the data and calculations it was concluded that the levels of effluent release from the Omaha TRIGA are very small

Reactor operation safety information document

Energy Technology Data Exchange (ETDEWEB)

1990-01-01

The report contains a reactor facility description which includes K, P, and L reactor sites, structures, operating systems, engineered safety systems, support systems, and process and effluent monitoring systems; an accident analysis section which includes cooling system anomalies, radioactive materials releases, and anticipated transients without scram; a summary of onsite doses from design basis accidents; severe accident analysis (reactor core disruption); a description of operating contractor organization and emergency planning; and a summary of reactor safety evolution. (MB)

Advanced Reactor Technology/Energy Conversion Project FY17 Accomplishments.

Energy Technology Data Exchange (ETDEWEB)

Rochau, Gary E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2018-02-01

The purpose of the ART Energy Conversion (EC) Project is to provide solutions to convert the heat from an advanced reactor to useful products that support commercial application of the reactor designs.

Radioactive release from VVER-1000 reactors after a terror attack

International Nuclear Information System (INIS)

Sdouz, G.

2005-01-01

Full text: One of the terror scenarios for nuclear power plants is a severe damage of the reactor containment caused by a plane crash or a missile. Due to the loss of electric power the cooling of the core is not maintained leading to a core melt accident. Normally in the course of severe accidents an intact containment has the ability to retain a large part of the radioactive inventory. The goal of this work is the investigation of the behavior of the radioactive release from a VVER-1000-type reactor during a severe accident with a large containment leak from the beginning of the accident. The results are compared with the release in a severe accident via a very small leakage due to the untightness of the containment. This work supplements a series of studies investigating the behavior of a VVER-1000-type reactor during severe accidents under different accident management strategies. The focus in this study is on the 'station blackout'-sequence (or TMLB' in the WASH-1400 nomenclature). The calculations were performed using the Source Term Code Package (STCP), hydrogen explosions are not considered. Up to the melt-through of the cavity bottom the thermal-hydraulics phenomena are almost identical to the TMLB'-case with an intact containment from the beginning. The phenomena occur slightly delayed due to the large containment leak. When the core-concrete-interaction begins the resulting gases leave the containment through the large leak and do not cause a pressure increase. The containment pressure remains at ambient pressure. Due to the different behavior and to the different release times of the nuclides the deviations to the scenario with an intact containment show a great variety. From this comparison it can be shown that the intact containment retains the nuclides up to a factor of 6000. (author)

The Brazilian Multipurpose Reactor (RMB) Project

Energy Technology Data Exchange (ETDEWEB)

Perrotta, Jose Augusto [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro, RJ (Brazil)

2012-07-01

Full text: The Plan of Action on Science, Technology and Innovation (PACT 2007-2010) of the Ministry of Science Technology and Innovation (MCTI), aligned to the governmental strategies for the Brazilian Nuclear Program, established as a goal the study and definition of the Brazilian Multipurpose Reactor (RMB). The RMB research reactor is designed to perform three main functions: radioisotope production for medicine, industry, agriculture and environmental applications; fuel and material irradiation testing in support to the Brazilian nuclear energy program; and to provide neutron beams for scientific and applied research. The main project facilities are: nuclear pool type reactor with a flux level compatible to the multipurpose uses; hot cells laboratory for Mo-99 and I-131 processing; hot cells laboratory for radioisotope processing; hot cells laboratory for irradiated material post irradiation analysis; neutron beams laboratory building with scientific equipment and instrumentation for researching; radiochemistry laboratory; radioactive waste treatment facility; support laboratories for operation and researching; and buildings for researchers and operators. This speech presents the RMB project status, giving some technical and management details on its development and its future perspectives for new jobs in research activities for the Brazilian technical and scientific community. (author)

The Brazilian Multipurpose Reactor (RMB) Project

International Nuclear Information System (INIS)

Perrotta, Jose Augusto

2012-01-01

Full text: The Plan of Action on Science, Technology and Innovation (PACT 2007-2010) of the Ministry of Science Technology and Innovation (MCTI), aligned to the governmental strategies for the Brazilian Nuclear Program, established as a goal the study and definition of the Brazilian Multipurpose Reactor (RMB). The RMB research reactor is designed to perform three main functions: radioisotope production for medicine, industry, agriculture and environmental applications; fuel and material irradiation testing in support to the Brazilian nuclear energy program; and to provide neutron beams for scientific and applied research. The main project facilities are: nuclear pool type reactor with a flux level compatible to the multipurpose uses; hot cells laboratory for Mo-99 and I-131 processing; hot cells laboratory for radioisotope processing; hot cells laboratory for irradiated material post irradiation analysis; neutron beams laboratory building with scientific equipment and instrumentation for researching; radiochemistry laboratory; radioactive waste treatment facility; support laboratories for operation and researching; and buildings for researchers and operators. This speech presents the RMB project status, giving some technical and management details on its development and its future perspectives for new jobs in research activities for the Brazilian technical and scientific community. (author)

Current status and perspective of advanced loop type fast reactor in fast reactor cycle technology development project

International Nuclear Information System (INIS)

Niwa, Hajime; Aoto, Kazumi; Morishita, Masaki

2007-01-01

After selecting the combination of the sodium-cooled fast reactor (SFR) with oxide fuel, the advanced aqueous reprocessing and the simplified pelletizing fuel fabrication as the most promising concept of FR cycle system, 'Feasibility Study on Commercialized Fast Reactor Cycle Systems' was finalized in 2006. Instead, a new project, Fast Reactor Cycle Technology Development Project (FaCT Project) was launched in Japan focusing on development of the selected concepts. This paper describes the current status and perspective of the advanced loop type SFR system in the FaCT Project, especially on the design requirements, current design as well as the related innovative technologies together with the development road-map. Some considerations on advantages of the advanced loop type design are also described. (authors)

Assessment of radiological releases to the environment from a fusion reactor power plant

International Nuclear Information System (INIS)

Shank, K.E.; Oakes, T.W.; Easterly, C.E.

1978-05-01

This report summarizes the expected tritium and activation-product inventories and presents an assessment of the potential radiological releases from a fusion reactor power plant, hypothetically located at the Oak Ridge National Laboratory. Routine tritium releases and the resulting dose assessment are discussed. Uncertainties associated with the conversion of tritium gas to tritium oxide and the global tritium cycling are evaluated. The difficulties of estimating releases of activated materials and the subsequent dose commitment are reviewed

Status of Kijang Resarch Reactor Project

Energy Technology Data Exchange (ETDEWEB)

Kim, Jee. Y; Kwon, T. H.; Kim, Jun. Y.; Oh, G. B. [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The High-flux Advanced Neutron Application Reactor (HANARO) is a multi-purpose reactor in Korea Atomic Energy Research Institute (KAERI) and is being utilized for neutron scattering experiments, material and fuel tests for nuclear power plants, radio-isotope (RI) productions, silicon doping, neutron activation analysis, and neutron radiography. In medical applications, the majority of RIs produced using HANARO are I-131 and Ir-192. Other RIs such as Mo-99 are coming from imports. The self-sufficiency of RI demand becomes an important issue for the public health service in Korea. In this regard the Kijang Research Reactor (KJRR) project was officially launched on the first of April 2012 in need to provide the self-sufficiency of RI demand including Mo-99, increase the neutron transportation doping (NTD) capacity and develop technologies related to the research reactor. When CP is granted, the first excavation is planned to start at the end of this year. In next year, pouring the first concrete and energizing 154kV will follow. In 2018, it is planned to complete utility building construction and reactor building construction.

20. Annual report. OECD Halden reactor project. 1979

International Nuclear Information System (INIS)

1981-01-01

This is the Twentieth Annual Report on the OECD Halden Reactor Project, describing activities during 1979, the first year of the 1979-1981 Halden Agreement. Research work at the project is focussed on three areas: 1) In-core behaviour of reactor fuel, particularly reliability and safety aspects, which is studied through irradiation of test fuel elements. 2) Prediction, surveillance and control of fuel and core performance, for which models of fuel and core behaviour are developed. 3) Applications of process computers to power plant control, for which prototype software systems and hardware arrangements are developed

Reactor-specific spent fuel discharge projections, 1984 to 2020

International Nuclear Information System (INIS)

Heeb, C.M.; Libby, R.A.; Holter, G.M.

1985-04-01

The original spent fuel utility data base (SFDB) has been adjusted to produce agreement with the EIA nuclear energy generation forecast. The procedure developed allows the detail of the utility data base to remain intact, while the overall nuclear generation is changed to match any uniform nuclear generation forecast. This procedure adjusts the weight of the reactor discharges as reported on the SFDB and makes a minimal (less than 10%) change in the original discharge exposures in order to preserve discharges of an integral number of fuel assemblies. The procedure used in developing the reactor-specific spent fuel discharge projections, as well as the resulting data bases themselves, are described in detail in this report. Discussions of the procedure cover the following topics: a description of the data base; data base adjustment procedures; addition of generic power reactors; and accuracy of the data base adjustments. Reactor-specific discharge and storage requirements are presented. Annual and cumulative discharge projections are provided. Annual and cumulative requirements for additional storage are shown for the maximum at-reactor (AR) storage assumption, and for the maximum AR with transshipment assumption. These compare directly to the storage requirements from the utility-supplied data, as reported in the Spent Fuel Storage Requirements Report. The results presented in this report include: the disaggregated spent fuel discharge projections; and disaggregated projections of requirements for additional spent fuel storage capacity prior to 1998. Descriptions of the methodology and the results are included in this report. Details supporting the discussions in the main body of the report, including descriptions of the capacity and fuel discharge projections, are included. 3 refs., 6 figs., 12 tabs

Influence of the rate of conversion of HT and HTO on projected radiation doses from release of molecular tritium

International Nuclear Information System (INIS)

Jacobs, D.G.; Easterly, C.E.; Phillips, J.E.

1979-01-01

Releases of tritium in the past have been largely in the form of tritiated water, and the projected radiation doses could be estimated by assuming tritium behaviour to parallel that of water. There is increasing interest in potential releases of tritium in the form of HT because of significant recent advances in fusion reactor research. Several recent studies have shown that bacteria containing the enzyme hydrogenase can catalyse the conversion of HT to HTO at rates several orders of magnitude faster than the rates measured in atmospheric systems. Rates of conversion in the soil have been combined with estimates of rates of permeation of HT into the soil and with global and local models depicting tritium transport and cycling. The results suggest that for the expected conversion rates, the impact on projected radiation doses should be relatively minor. (author)

Biological Phosphorus Release and Uptake Under Alternating Anaerobic and Anoxic Conditions In a Fixed-Film Reactor

DEFF Research Database (Denmark)

Kerrn-Jespersen, Jens Peter; Henze, Mogens; Strube, Rune

1994-01-01

Biological phosphorus removal was investigated in a fixed-film reactor with alternating anaerobic and anoxic conditions. The tests showed that biological phosphorus removal can be obtained in a fixed-film reactor with nitrate as oxidising agent. In the anaerobic period, 0.52 mg of PO4-P...... was released per mg of acetate taken up on an average. In the anoxic period, 2.0 mg of PO4-P was taken up per mg of NO3-N reduced on an average. The relationship between potassium released and phosphate released in the anaerobic phase was determined to be 0.37 mg K/mg P, while the relationship between...

Release of radioactive fission products from BN-600 reactor untight fuel elements

International Nuclear Information System (INIS)

Osipov, S.L.; Tsikunov, A.G.; Lisitsin, E.C.

1996-01-01

The experimental data on the release of radioactive fission products from BN-600 reactor untight fuel elements are given in the report. Various groups of radionuclides: inert gases Xe, Kr, volatile Cs, J, non-volatile Nb, and La are considered. The results of calculation-experimental study of transfer and distribution of radionuclides in the reactor primary circuit, gas system and sodium coolant are considered. It is shown that some complex radioactivity transfer processes can be described by simple mathematical models. (author)

Effect of electromagnetic radiation on the release of tritium from a fusion reactor

International Nuclear Information System (INIS)

Causey, R.A.

1982-01-01

Electromagnetic radiation may play an important role in determining the amount of tritium that passes through the first wall of a fusion reactor. Photons enhance the outgassing of hydrogen from metal surfaces and therefore lower the surface concentration. The diffusion coefficient for hydrogen in metals is also increased by photon interactions. The importance of these processes on the tritium release depends on the actual conditions that will exist in the fusion reactor. Because electromagnetic radiation stimulates the release of tritium from traps, it could also affect the tritium inventory in the first wall. The effects of electromagnetic radiation on hydrogen in metals have been reviewed. Because electrons are produced by high energy photons, the effect of electrons on hydrogen has also been included

The brief introduction to decommissioning of nuclear reactor projects

International Nuclear Information System (INIS)

Zhao Shixin

1991-01-01

The basic concept and procedure of the decommissioning of nuclear reactor project and the three stages of decommissioning defined by IAEA are introduced. The main work of decommissioning of nuclear reactor are as following: (1) the documentary and technological preparation; (2) the site preparation of decommissioning project; (3) the dismantling of equipment piping system and components; (4) the decontamination of the piping system before and after decomminssioning; (5) the storage and disposal of the operational and decommissioning waste

The brief introduction to decommissioning of nuclear reactor projects

Energy Technology Data Exchange (ETDEWEB)

Shixin, Zhao [Beijing Inst. of Nuclear Engineering (China)

1991-08-01

The basic concept and procedure of the decommissioning of nuclear reactor project and the three stages of decommissioning defined by IAEA are introduced. The main work of decommissioning of nuclear reactor are as following: (1) the documentary and technological preparation; (2) the site preparation of decommissioning project; (3) the dismantling of equipment piping system and components; (4) the decontamination of the piping system before and after decomminssioning; (5) the storage and disposal of the operational and decommissioning waste.

Reactors Project Delivery: The Value of Experiance

International Nuclear Information System (INIS)

Stosic, V. Zoran

2014-01-01

State of Affairs: Energy Potential and Density versus Environmental Load of different Energy Sources, Development of Fuel into Energy/Electricity Generation, Production Costs of Electricity, Contributions of Nuclear Energy to Security of Energy Supply, Recent Nuclear Development, Public Support growing again. Projects Status: Reactors under Construction, Different Projects Industrial Schemes, Projects Overview. The Value of Experience: Licensing, Standardization on Early Engineering Activities, Supply Chain and Manufacturing of Heavy Components, Installation, Procurement. (author)

Process for the transport of heat energy released by a nuclear reactor

International Nuclear Information System (INIS)

Nuernberg, H.W.; Wolff, G.

1978-01-01

The heat produced in a nuclear reactor is converted into latent chemical binding energy. The heat can be released again below 400 0 C by recombination after transport by decomposition of ethane or propane into ethylene or propylene and hydrogen. (TK) [de

Programmes and projects for high-temperature reactor development

International Nuclear Information System (INIS)

Bogusch, Edgar; Hittner, Dominique

2009-01-01

An increasing attention has to be recognised worldwide on the development of High-Temperature Reactors (HTR) which has started in Germany and other countries in the 1970ies. While pebble bed reactors with spherical fuel elements have been developed and constructed in Germany, countries such as France, the US and Russia investigated HTR concepts with prismatic block-type fuel elements. The concept of a modular HTR formerly developed by Areva NP was an essential basis for the HTR-10 in China. A pebble bed HTR for electricity production is developed in South Africa. The construction is planned after the completion of the licensing procedure. Also the US is planning an HTR under the NGNP (Next Generation Nuclear Plant) Project. Due to the high temperature level of the helium coolant, the HTR can be used not only for electricity production but also for supply of process heat. Including its inherent safety features the HTR is an attractive candidate for heat supply to various types of plants e.g. for hydrogen production or coal liquefactions. The conceptual design of an HTR with prismatic fuel elements for the cogeneration of electricity and process heat has been developed by Areva NP. On the European scale the HTR development is promoted by the RAPHAEL (ReActor for Process heat, Hydrogen And ELectricity generation) project. RAPHAEL is an Integrated Project of the Euratom 6th Framework Programme for the development of technologies towards a Very High-Temperature Reactor (VHTR) for the production of electricity and heat. It is financed jointly by the European Commission and the partners of the HTR Technology Network (HTR-TN) and coordinated by Areva NP. The RAPHAEL project not only promotes HTR development but also the cooperation with other European projects such as the material programme EXTREMAT. Furthermore HTR technology is investigated in the frame of Generation IV International Forum (GIF). The development of a VHTR with helium temperatures above 900 C for the

Seismic isolation of lead-cooled reactors: The European project SILER

International Nuclear Information System (INIS)

Forni, Massimo; Poggianti, Alessandro; Scipinotti, Riccardo; Dusi, Alberto; Manzoni, Elena

2014-01-01

SILER (Seismic-Initiated event risk mitigation in LEad-cooled Reactors) is a Collaborative Project, partially funded by the European Commission in the 7th Framework Programme, aimed at studying the risk associated to seismic-initiated events in Generation IV Heavy Liquid Metal reactors, and developing adequate protection measures. The project started in October 2011, and will run for a duration of three years. The attention of SILER is focused on the evaluation of the effects of earthquakes, with particular regards to beyond-design seismic events, and to the identification of mitigation strategies, acting both on structures and components design. Special efforts are devoted to the development of seismic isolation devices and related interface components. Two reference designs, at the state of development available at the beginning of the project and coming from the 6th Programme, have been considered: ELSY (European Lead Fast Reactor) for the Lead Fast Reactors (LFR), and MYRRHA (Multi-purpose hYbrid Research Reactor for High-tech Applications) for the Accelerator-Driven Systems (ADS). This paper describes the main activities and results obtained so far, paying particular attention to the development of seismic isolators, and the interface components which must be installed between the isolated reactor building and the non-isolated parts of the plant, such as the pipe expansion joints and the joint-cover of the seismic gap.

OECD Halden reactor project

International Nuclear Information System (INIS)

1977-01-01

The activities of the OECD Halden Reactor Project for the year 1975 are summarized. The period under review is the last year of the three year joint programme which commenced on 1st January, 1973. The main items reported upon are: process supervision and control, test fuel irradiation and fuel research, reactor operations, and administration and finance. The process supervision and control work has been concentrated in two fields: methods development for core surveillance and control, and systems development for operator-process communication. As for fuel test, investigations of the densification phenomenon have continued through irradiations to a maximum of about 16000MWd/tUO 2 . Axial and radial deformations of fuel rods are studied, with the effect of power transients upon the dimensional stability of fuel rods, and fuel-cladding heat transfer and fuel temperature. Thermal models for steady state and transient heat transfer in fuel rods have been developed and the work on thermomechanical models of claddings shows considerable promise

Techniques to limit gaseous releases in case of reactor accident. Choice criteria - present solutions

International Nuclear Information System (INIS)

Billard, Francois; Lavie, Jean-Marie

1964-10-01

Within the frame of the study of radiological risks associated with a reactor accident in order to define the required responses, this study comprises, on the one hand, an analysis of the different accident types in order to select typical accidents, and on the other hand, a site-based analysis to define the maximum admissible radioactivity release for a given site. The determination of minimum required coefficient of risk reduction results from a compromise between the choice of reactor configuration type and the efficiency of purification devices, while taking into account minimum characteristics of the enclosure mechanical strength, local release conditions, and nature of gaseous effluents to be processed. After a review of available containment techniques, the author applies this analysis method to the different French reactor types. He gives a brief description of adopted solutions for the most typical French reactors in terms of characteristics of venting and filtration devices. As data quality is a crucial requirement, the author outlines the need for further studies regarding fission product emission and transfer, the purification of gaseous effluents and their diffusion in the atmosphere [fr

Thorium-based Molten Salt Reactor (TMSR) project in China

International Nuclear Information System (INIS)

Dai, Zhimin; Liu, Wei

2013-01-01

Making great efforts in development of nuclear energy is one of the long-term-plan in China's energy strategies. The advantages of Thorium-based nuclear energy are: rich resource in nature, less nuclear waste, low toxicity, nuclear non-proliferation and so on. Furthermore, China is a country with abundant thorium, thus it is necessary to develop the Thorium-based Molten Salt Reactor (TMSR) in China. Shanghai Institute of Applied Physics, Chinese Academy of Sciences (SINAP) had designed and constructed the first China's light-water reactor and developed a zero-power thorium-based molten salt reactor successfully in the early 1970s. The applied research project 'thorium molten salt reactor nuclear power system' by SINAP together with several other institutes had been accepted and granted by China government in 2011. The whole project has been divided into three stages: Firstly, built a 2 MW-zero-power high temperature solid molten salt reactor in 2015 and a 2 MW-zero-power high temperature liquid molten salt reactor in 2017. Secondly, in 2020 built a 10 MW high temperature liquid molten salt reactor. Thirdly, on the base of previous work, a 100 MW high temperature molten salt reactor should be achieving in 2030. After more than one years of efforts, a high quality scientific research team has been formed, which is able to design the molten salt reactor, the molten salt loop and related key equipment, the systems of molten salt preparation, purification and the radioactive gas removal. In the past one year, the initial physical design of high temperature molten salt reactor has been completed; the nuclear chemistry and radiation chemical laboratory has been built, a high temperature salt (HTS) loop and radioactive gas removal experiment device system have been successfully developed and constructed. Further, the preliminary study on reactor used carbon-carbon composite material has been investigated. (author)

The collaborative project on European sodium fast reactor (CP ESFR project)

International Nuclear Information System (INIS)

Fiorini, Gian-Luigi

2010-01-01

The paper summarizes the key characteristics of the four years large Collaborative Project on European Sodium Fast Reactor (CP ESFR - 2009-2012); the CP ESFR follows the 6th FP project named 'Roadmap for a European Innovative SOdium cooled FAst Reactor - EISOFAR' further identifying, organizing and implementing a significant part of the needed R and D effort. The paper also gives insights concerning the so called 'working horses' cores and systems which are provided by CEA and AREVA and that will be used as a basis to test the performances and assess the pertinence of innovative solutions. The CP ESFR merges the contribution of 25 European partners (EU + CH); it will be performed under the aegis of the 7th Euratom FP under the Area - Advanced Nuclear Systems with a refund from the European Commission. It will be a key component of the European Sustainable Nuclear Energy Technology Platform (SNE TP) and its Strategic Research Agenda (SRA). The inputs for the project are the key research goals for fourth generation of European sodium cooled fast reactors which can be summarized as follows: an improved safety with in particular the achievement of a robust architecture vis-a-vis of abnormal situations and the robustness of the safety demonstrations; the guarantee of a financial risk similar to that of the other means of energy production; a flexible and robust management of nuclear materials and especially waste reduction through Minor Actinides burning

Local Fission Gas Release and Swelling in Water Reactor Fuel during Slow Power Transients

DEFF Research Database (Denmark)

Mogensen, Mogens Bjerg; Walker, C.T.; Ray, I.L.F.

1985-01-01

Gas release and fuel swelling caused by a power increase in a water reactor fuel (burn-up 2.7–4.5% FIMA) is described. At a bump terminal level of about 400 W/cm (local value) gas release was 25–40%. The formation of gas bubbles on grain boundaries and their degree of interlinkage are the two...... factors that determine the level of fission gas release during a power bump. Release begins when gas bubbles on grain boundaries start o interlink. This occurred at r/r0 ~ 0.75. Release tunnels were fully developed at r/r0 ~ 0.55 with the result that gas release was 60–70% at this position....

Notes on a homogeneous reactor project; Idees sur un projet de reacteur homogene

Energy Technology Data Exchange (ETDEWEB)

Benveniste, J; Bernot, J; Eidelman, D; Grenon, M; Portes, L; Raspaud, G; Tachon, J; Vendryes, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Berthod, L; Cohen de Lara, G; Delachanal, M; Fontanet, P; Halbronn, G [Societe Grenobloise d' Etudes et d' Applications Hydrauliques, 38 (France)

1958-07-01

An attempt has been made to develop certain ideas concerning homogeneous reactors. The project under consideration is based on the simultaneous use of a suspension of uranium dispersed in heavy or light water and of boiling in the reactor for heat extraction. However, the studies of suspensions and of boiling are relatively independent and can also be developed for reactors of different types using one or the other. Our aim is a minimum investment in fissile material; for this we propose to extract the steam directly from the core and to make use of a cyclone to accelerate this extraction; a cyclone-type circulation creating a field of increasing tangential velocities of the fluid towards the axis causes the droplets of vapour to accelerate towards the axial vortex in which they are collected; the steam output is then evacuated to the external heat utilisation system, for example an exchanger of the condenser-boiler type. The input speed of water into the reactor being one of the important parameters in the running of the pile, a spiral supply input chamber is used, allowing this speed to be regulated in amount and direction. (author)Fren. [French] Nous nous sommes attaches a developper certaines idees relatives aux piles homogenes. Le projet que nous etudions est base sur l'emploi simultane d'une suspension contenant de l'uranium disperse dans l'eau legere ou lourde et de l'ebullition dans le reacteur pour l'extraction de chaleur. Neanmoins, les etudes de suspensions et d'ebullition sont relativement independantes et peuvent egalement etre developpees pour des reacteurs de type different utilisant l'une ou l'autre. Le but que nous cherchons a atteindre est un investissement minimum en matiere fissile; pour cela, nous proposons d'extraire directement la vapeur dans le coeur et de recourir a un dispositif cyclone pour accelerer cette extraction; une circulation type cyclone creant un champ de vitesses tangentielles du fluide croissantes veraxe a pour effet d

Simplified method for measuring the response time of scram release electromagnet in a nuclear reactor

Energy Technology Data Exchange (ETDEWEB)

Patri, Sudheer, E-mail: patri@igcar.gov.in; Mohana, M.; Kameswari, K.; Kumar, S. Suresh; Narmadha, S.; Vijayshree, R.; Meikandamurthy, C.; Venkatesan, A.; Palanisami, K.; Murthy, D. Thirugnana; Babu, B.; Prakash, V.; Rajan, K.K.

2015-04-15

Highlights: • An alternative method for estimating the electromagnet clutch release time. • A systematic approach to develop a computer based measuring system. • Prototype tests on the measurement system. • Accuracy of the method is ±6% and repeatability error is within 2%. - Abstract: The delay time in electromagnet clutch release during a reactor trip (scram action) is an important safety parameter, having a bearing on the plant safety during various design basis events. Generally, it is measured using current decay characteristics of electromagnet coil and its energising circuit. A simplified method of measuring the same in a Sodium cooled fast reactors (SFR) is proposed in this paper. The method utilises the position data of control rod to estimate the delay time in electromagnet clutch release. A computer based real time measurement system for measuring the electromagnet clutch delay time is developed and qualified for retrofitting in prototype fast breeder reactor. Various stages involved in the development of the system are principle demonstration, experimental verification of hardware capabilities and prototype system testing. Tests on prototype system have demonstrated the satisfactory performance of the system with intended accuracy and repeatability.

An Overview of the International Reactor Physics Experiment Evaluation Project

International Nuclear Information System (INIS)

Briggs, J. Blair; Gulliford, Jim

2014-01-01

Interest in high-quality integral benchmark data is increasing as efforts to quantify and reduce calculational uncertainties associated with advanced modeling and simulation accelerate to meet the demands of next generation reactor and advanced fuel cycle concepts. Two Organization for Economic Cooperation and Development (OECD) Nuclear Energy Agency (NEA) activities, the International Criticality Safety Benchmark Evaluation Project (ICSBEP), initiated in 1992, and the International Reactor Physics Experiment Evaluation Project (IRPhEP), initiated in 2003, have been identifying existing integral experiment data, evaluating those data, and providing integral benchmark specifications for methods and data validation for nearly two decades. Data provided by those two projects will be of use to the international reactor physics, criticality safety, and nuclear data communities for future decades. An overview of the IRPhEP and a brief update of the ICSBEP are provided in this paper.

Inertial Fusion Energy reactor design studies: Prometheus-L, Prometheus-H

International Nuclear Information System (INIS)

Waganer, L.M.; Driemeyer, D.E.; Lee, V.D.

1992-03-01

This report contains a review of design studies for inertial confinement reactors. The first of three volumes briefly discusses the following: Introduction; Key objectives, requirements, and assumptions; Systems modeling and trade studies; Prometheus-L reactor plant design overview; Prometheus-H reactor plant design overview; Key technical issues and R ampersand D requirements; Comparison of IFE designs; and study conclusions

Decommissioning of TRIGA Mark II type reactor

Energy Technology Data Exchange (ETDEWEB)

Hwang, Dooseong; Jeong, Gyeonghwan; Moon, Jeikwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2012-10-15

The first research reactor in Korea, KRR 1, is a TRIGA Mark II type with open pool and fixed core. Its power was 100 kWth at its construction and it was upgraded to 250 kWth. Its construction was started in 1957. The first criticality was reached in 1962 and it had been operated for 36,000 hours. The second reactor, KRR 2, is a TRIGA Mark III type with open pool and movable core. These reactors were shut down in 1995, and the decision was made to decommission both reactors. The aim of the decommissioning activities is to decommission the KRR 2 reactor and decontaminate the residual building structures and site, and to release them as unrestricted areas. The KRR 1 reactor was decided to be preserve as a historical monument. A project was launched for the decommissioning of these reactors in 1997, and approved by the regulatory body in 2000. A total budget for the project was 20.0 million US dollars. It was anticipated that this project would be completed and the site turned over to KEPCO by 2010. However, it was discovered that the pool water of the KRR 1 reactor was leaked into the environment in 2009. As a result, preservation of the KRR 1 reactor as a monument had to be reviewed, and it was decided to fully decommission the KRR 1 reactor. Dismantling of the KRR 1 reactor takes place from 2011 to 2014 with a budget of 3.25 million US dollars. The scope of the work includes licensing of the decommissioning plan change, removal of pool internals including the reactor core, removal of the thermal and thermalizing columns, removal of beam port tubes and the aluminum liner in the reactor tank, removal of the radioactive concrete (the entire concrete structure will not be demolished), sorting the radioactive waste (concrete and soil) and conditioning the radioactive waste for final disposal, and final statuses of the survey and free release of the site and building, and turning over the site to KEPCO. In this paper, the current status of the TRIGA Mark-II type reactor

Role of Halden Reactor Project for world-wide nuclear energy development

Energy Technology Data Exchange (ETDEWEB)

McGrath, M.A.; Volkov, B.

2011-07-01

The great interest for utilization of nuclear materials to produce energy in the middle of last century needed special investigations using first class research facilities. Common problems in the area of nuclear fuel development motivated the establishment of joint research efforts. The OECD Halden Reactor Project (HRP) is a good example of such a cooperative research effort, which has been performing for more than 50 years. During that time, the Halden Reactor evolved from a prototype heavy water reactor envisaged as a power source for different applications to a research reactor that is able to simulate in-core conditions of modern commercial power reactors. The adaptability of the Halden Reactor enables the HRP to be an important international test facility for nuclear fuels and materials development. The long-term international cooperation is based on the flexible HRP organizational structure which also provides the continued success. [1,2] This paper gives a brief history of the Halden Reactor Project and its contribution to world-wide nuclear energy development. Recent expansion of the Project to the East and Asian countries may also assist and stimulate the development of a nuclear industry within these countries. The achievements of the HRP rely on the versatility of the research carried out in the reactor with reliable testing techniques and in-pile instrumentation. Diversification of scientific activity in the areas of development of alternative energy resources and man-machine technology also provide the HRP with a stable position as one of the leaders in the world scientific community. All of these aspects are described in this paper together with current experimental works, including the investigation of ULBA (Kazakhstan) production fuel in comparison with other world fuel suppliers, as well as other future and prospective plans of the Project.(Author)

Role of Halden Reactor Project for world-wide nuclear energy development

International Nuclear Information System (INIS)

McGrath, M.A.; Volkov, B.

2011-01-01

The great interest for utilization of nuclear materials to produce energy in the middle of last century needed special investigations using first class research facilities. Common problems in the area of nuclear fuel development motivated the establishment of joint research efforts. The OECD Halden Reactor Project (HRP) is a good example of such a cooperative research effort, which has been performing for more than 50 years. During that time, the Halden Reactor evolved from a prototype heavy water reactor envisaged as a power source for different applications to a research reactor that is able to simulate in-core conditions of modern commercial power reactors. The adaptability of the Halden Reactor enables the HRP to be an important international test facility for nuclear fuels and materials development. The long-term international cooperation is based on the flexible HRP organizational structure which also provides the continued success. [1,2] This paper gives a brief history of the Halden Reactor Project and its contribution to world-wide nuclear energy development. Recent expansion of the Project to the East and Asian countries may also assist and stimulate the development of a nuclear industry within these countries. The achievements of the HRP rely on the versatility of the research carried out in the reactor with reliable testing techniques and in-pile instrumentation. Diversification of scientific activity in the areas of development of alternative energy resources and man-machine technology also provide the HRP with a stable position as one of the leaders in the world scientific community. All of these aspects are described in this paper together with current experimental works, including the investigation of ULBA (Kazakhstan) production fuel in comparison with other world fuel suppliers, as well as other future and prospective plans of the Project.(Author)

Characteristics of D(-3)He fueled FRC reactor: ARTEMIS-L

Science.gov (United States)

Momota, H.; Motojima, O.; Okamoto, M.; Sudo, S.; Tomita, Y.; Yamaguchi, S.; Iiyoshi, A.; Onozuka, M.; Ohnishi, M.; Uenosono, C.

1993-11-01

The characteristics of D(-3)He fueled commercial fusion reactor ARTEMIS-L are discussed. By using favorable characteristics of a field-reversed configuration, the fusion plasma of ARTEMIS-L becomes compact and its veta-value is extremely high. Consequently, it is possible to construct an economical fusion power plant based on this concept. The life of the structural materials is found during the full reactor life (30 years) and the safety of the reactor is intrinsic to D(-3)He fuels. The amount of disposed materials is rather small and the level of the intruder dose is so low that the plant appears to be acceptable in regards to the environment.

Dynamic evaluation of environmental impact due to tritium accidental release from the fusion reactor.

Science.gov (United States)

Nie, Baojie; Ni, Muyi; Jiang, Jieqiong; Wu, Yican

2015-10-01

As one of the key safety issues of fusion reactors, tritium environmental impact of fusion accidents has attracted great attention. In this work, the dynamic tritium concentrations in the air and human body were evaluated on the time scale based on accidental release scenarios under the extreme environmental conditions. The radiation dose through various exposure pathways was assessed to find out the potential relationships among them. Based on this work, the limits of HT and HTO release amount for arbitrary accidents were proposed for the fusion reactor according to dose limit of ITER. The dynamic results aim to give practical guidance for establishment of fusion emergency standard and design of fusion tritium system. Copyright © 2015 Elsevier Ltd. All rights reserved.

Fessenheim simulator for OECD Halden Reactor Project

International Nuclear Information System (INIS)

Oudot, G.; Bonnissent, B.

1998-01-01

A full scope NPP simulator is presently under manufacture by THOMSON TRAINING and SIMULATION (TTandS) in Cergy (France) for the OECD HALDEN REACTOR PROJECT. The reference plant of this simulator is the Fessenheim CP0 PWR power plant operated by the French utility EDF, for which TTandS has delivered a full scope training simulator in mid 1997. The simulator for HALDEN Reactor Project is based on a software duplication of the Fessenheim simulator delivered to EDF, ported on the most recent computers and O.S. available. This paper outlines the main features of this new simulator generation which reaps benefit of the advanced technologies of the SIPA design simulator introduced inside a full scope simulator. This kind of simulator is in fact the synthesis between training and design simulators and offers therefore added technical capabilities well suited to HALDEN needs. (author)

The calculating methods of the release of airborne radionuclides to environment during the normal operation of a module high temperature gas-cooled reactor

International Nuclear Information System (INIS)

Liu Yuanzhong

1993-01-01

The calculations of the release of radionuclides to environment are the basis of environmental impact assessment during the normal operation of a module high temperature gas-cooled reactor of the Institute of Nuclear Energy Technology, Tsinghua University, China. According to the features of the reactor it is pointed out that only five sources of the airborne radioactive materials released to environment are important. They are: (1) the activation of the air in the reactor cavity; (2) the escape from the primary coolant systems; (3) the release of radioactively contaminated helium from storage tanks; (4) the release of radioactively contaminated helium from the gas evacuation system of fuel load and unload system; (5) the leakage of the vapour from water-steam loop. In accordance with five release sources the calculating methods of radionuclides released to environment are worked out respectively and the respective calculating formulas are derived for the normal operation of the reactor

Overview of the OECD Halden reactor project

International Nuclear Information System (INIS)

Vitanza, C.

2000-01-01

The OECD Halden Reactor Project is an international network dedicated to enhancing the safety and reliability of nuclear power plants. The project operates under the auspices of the OECD Nuclear Energy Agency and aims at addressing and resolving issues relevant to safety as they emerge in the nuclear community. This paper gives a concise presentation of the project's goals and of its technical infrastructure. The paper also contains a brief overview of results from the ongoing programme and of the main issues contemplated for the next three-year programme period (2000-2002). (author)

Environmental Release Prevention and Control Plan

International Nuclear Information System (INIS)

Mamatey, A.; Arnett, M.

1997-01-01

During the history of SRS, continual improvements in facilities, process, and operations, and changes in the site''s mission have reduced the amount of radioactive liquid releases. In the early years of SRS (1958 to 1965), the amount of tritium discharged to the Savannah River averaged approximately 61,000 curies a year. During the mid-1980''s (1983 to 1988), liquid releases of tritium averaged 27,000 curies a year. By 1996, liquid releases of tritium are projected to be just 3000 curies for the year. This large projected decrease is the result of the planned shut-down of all reactors and the anticipated significant decline in the amount of tritium migrating from the site seepage basins and the Solid Waste Disposal Facility

Study of applying the Atmospheric Release Advisory Capability to nuclear power plants

International Nuclear Information System (INIS)

Orphan, R.C.

1978-06-01

Each utility licensee for a nuclear power reactor is required to minimize the adverse effects from an accidental radionuclide release into the atmosphere. In the past the ability to forecast quantitatively the extent of the hazard from such a release has been limited. Now powerful atmospheric modeling techniques are available to assist nuclear reactor site officials with greatly improved assessments. Lawrence Livermore Laboratory (LLL) has developed a prototype system called the Atmospheric Release Advisory Capability (ARAC) which is designed to integrate the modeling with advanced sensors, data handling techniques, and weather data in order to provide timely, usable advisories to the site officials. The purpose of this project is to examine the ways and means of adapting ARAC for application to many nuclear power reactors widely dispersed across the nation. The project will emphasize the management aspects, including government-industry relationships, technology transfer, organizational structure, staffing, implementing procedures, and costs. Benefits and costs for several alternative systems will be compared. The results will be reviewed and evaluated by the management and staff of the ARAC project at LLL and also by selected staff members of the sponsoring government agency

The PALLAS research and isotope reactor project status

International Nuclear Information System (INIS)

Van Der Schaaf, B.; De Jong, P.

2010-01-01

In the European Union the first generation research reactors is nearing their end of life condition. Several committees recommend a comprehensive set of reactors in the EU, amongst them the replacement for the HFR research and isotope reactor in Petten: PALLAS. The business case for PALLAS supports a future for a research and isotope reactor in Petten as a perfect fit for the future EU set of test reactors. The tender for PALLAS started in 2007, following the EU rules for tendering complex objects with the competitive dialogue. This procedure involved an extensive consultation phase between individual tendering companies and NRG, resulting in definitive specifications in summer 2008. The evaluation of offers, including conceptual designs, took place in summer 2009. At present NRG is still active in the acquisition of the funding for the project. The licensing path has been started in autumn 2009 with a initiation note on the environmental impact assessment, EIA. The public hearings held in the lead to the advice from the national EIA committee for the approach of the assessment. The PALLAS project team in Petten will guide the design and build processes. It is also responsible for the licensing of the building and operation of PALLAS. The team also manages the design and construction for the infrastructure, such as cooling devices, including remnant heat utilization, and utility provisions. A particular responsibility for the team is the design and construction of experimental and isotope capsules, based on launch customer requirements. (author)

D-3He fueled FRC reactor 'ARTEMIS-L'

International Nuclear Information System (INIS)

Momota, Hiromu; Tomita, Yukihiro; Ishida, Akio; Kohzaki, Yasuji; Nakao, Yasuyuki; Nishikawa, Masabumi; Ohi, Shoichi; Ohnishi, Masami.

1992-09-01

A neutron-lean D- 3 He fueled field reversed configuration (FRC) fusion reactor is studied on the bases of former high-efficiency ARTEMIS design. Certain improvements such as effective axial contracting plasma heating and cusp-type direct energy converters as well as an empirical scale of the energy confinement are introduced. The resultant total neutron load onto the first wall of the plasma chamber is as low as 0.1 MW/m 2 , which enable the life of the first wall or the structural materials to be longer than the whole life of the reactor. The attractive characteristics of the neutron-lean reactor follow in the ARTEMIS design: it is socially acceptable in views of radioactivity and fuel resources, and the cost of electricity appears to be cheap compared with that from a light water reactor. Critical physics and engineering issues for performing the ARTEMIS-L reactor are clarified. (author)

Consequences of tritium release to water pathways from postulated accidents in a DOE production reactor

International Nuclear Information System (INIS)

O'Kula, K.R.; Olson, R.L.; Hamby, D.M.

1991-01-01

A full-scale PRA of a DOE production reactor has been completed that considers full release of tritium as part of the severe accident source term. Two classes of postulated reactor accidents, a loss-of-moderator pumping accident and a loss-of-coolant accident, are used to bound the expected dose consequence from liquid pathway release. Population doses from the radiological release associated with the two accidents are compared for aqueous discharge and atmospheric release modes. The expectation values of the distribution of possible values for the societal effective dose equivalent to the general public, given a tritium release to the atmosphere, is 2.8 person-Sv/PBq (9.9 x 10 -3 person-rem/Ci). The general public drinking water dose to downstream water consumers is 6.5 x 10 -2 person-Sv/Pbq (2.4 x 10 -4 person-rem/Ci) for aqueous releases to the surface streams eventually reaching the Savannah River. Negligible doses are calculated for freshwater fish and saltwater invertebrate consumption, irrigation, and recreational use of the river, given that an aqueous release is assumed to occur. Relative to the balance of fission products released in a hypothetical severe accident, the tritium-related dose is small. This study suggests that application of regional models (1610 km radius) will indicate larger dose consequences from short-term tritium release to the atmosphere than from comparable tritium source terms to water pathways. However, the water pathways assessment is clearly site-specific, and the overall aqueous dose will be dependent on downstream receptor populations and uses of the river

OECD Halden Reactor Project

International Nuclear Information System (INIS)

1983-01-01

The OECD Halden Reactor Project is both the oldest and the only one still in operation of the three major joint undertakings established at the inception of the OECD Nuclear Energy Agency. This publication has been printed in connection with its twenty-fifth anniversary as an international project. After presentation of the history and organization of the project, a thorough description of the past and present activities in the field of fuel performance and process control and surveillance is given. The projects's fuel testing programme is now focuessed on an investigation to define safety margins under normal operations as well as under various kinds of accident situations. Fuel research is also concerned with the characterisation of long term effects with regard to efficiency, operational safety and mapping of reliability and durability in the case of accidents with loss of coolant. In the field of process control and surveillance, research work is directly linked to the use of computers and colour graphics as tools in the control room. A fullscale simulator-based model and experimental control room has been constructed. The first experiments to be carried out in this laboratory will investigate the advantage of analysing alarms before they are presented to the operator. (RF)

Investigation of activity release during light water reactor core meltdown

International Nuclear Information System (INIS)

Albrecht, H.; Matschoss, V.; Wild, H.

1978-01-01

A test facility was developed for the determination of activity release and of aerosol characteristics under realistic light water reactor core melting conditions. It is composed of a high-frequency induction furnace, a ThO 2 crucible system, and a collection apparatus consisting of membrane and particulate filters. Thirty-gram samples of a representative core material mixture (corium) were melted under air, argon, or steam at 0.8 to 2.2 bar. In air at 2700 0 C, for example, the relative release was 0.4 to 0.7% for iron, chromium, and cobalt and 4 to 11% for tin, antimony, and manganese. Higher release values of 20 to 40% at lower temperatures (2150 0 C, air) were found for selenium, cadmium, tellurium, and cesium. The size distribution of the aerosol particles was trimodal with maxima at diameters of 0.17, 0.30, and 0.73 μm. The result of a qualitative x-ray microanalysis was that the main elements of the melt were contained in each aerosol particle. Further investigations will include larger melt masses and the additional influence of concrete on the release and aerosol behavior

Environmental impact assessment of Ar-41 released by the normal operation of TRIGA-Mark 2 research reactor

International Nuclear Information System (INIS)

Qassoud, D.; Soufi, I.; Ziagos, J.; Demir, Z

2007-01-01

Full text: In accordance with the international regulation of nuclear safety and radiological protection of the environment applicable to the basic nuclear installations, category in which the Triga-Mark 2 research reactor is considered, an assesment of the impact in to the environment of the Ar-41 radioelement is accomplished. This radioelement is released by the normal operation of this reactor. The assessment is based on the characteristics of a Moroccan site (where the reactor is installed). It is carried out using CEA Gaussian models and mathematical models developed in LLNL. Considering the assumptions of impact assessments of the radioactivity in the atmosphere, the most important exposure is relatively corresponding to 1 Km from the reactor. This exposure is approximately 0,07% of the lawful limit. Beyond this locality, the exposure becomes lower than 0,02% of this limit. Beyond 5 Km, it becomes lower than ten nono-Sivert. In the basis of the site radiological baseline, the environmental impact of Ar-41 released in normal operation of the reactor is negligible in the studied case. [fr

Safety Research Experiment Facility Project. Conceptual design report. Volume IV. Reactor containment

International Nuclear Information System (INIS)

1975-12-01

The principal purpose of the SAREF Reactor Containment Building (RCB) is to prevent the uncontrolled release of radioactive materials to the atmosphere as a result of accidental occurrences inside the containment. The RCB houses numerous reactor systems and components including the Prestressed Concrete Reactor Vessel (PCRV). The design of the RCB is of reinforced concrete (steel-lined). The containment building is embedded nearly 100 feet in lava rock. It has therefore been necessary to independently formulate an appropriate and conservative design approach

Regulatory Framework for Controlling the Research Reactor Decommissioning Project

International Nuclear Information System (INIS)

Melani, Ai; Chang, Soon Heung

2009-01-01

Decommissioning is one of important stages in construction and operation of research reactors. Currently, there are three research reactors operating in Indonesia. These reactors are operated by the National Nuclear Energy Agency (BATAN). The age of the three research reactors varies from 22 to 45 years since the reactors reached their first criticality. Regulatory control of the three reactors is conducted by the Nuclear Energy Regulatory Agency (BAPETEN). Controlling the reactors is carried out based on the Act No. 10/1997 on Nuclear Energy, Government Regulations and BAPETEN Chairman Decrees concerning the nuclear safety, security and safeguards. Nevertheless, BAPETEN still lack of the regulation, especially for controlling the decommissioning project. Therefore, in the near future BAPETEN has to prepare the regulations for decommissioning, particularly to anticipate the decommissioning of the oldest research reactors, which probably will be done in the next ten years. In this papers author give a list of regulations should be prepared by BAPETEN for the decommissioning stage of research reactor in Indonesia based on the international regulatory practice

Fission product release during MCCI. CEC nuclear safety program: MCCI project

Energy Technology Data Exchange (ETDEWEB)

Cenerino, G [CEA Centre d` Etudes Nucleaires de Fontenay-aux-Roses, 92 (France). Inst. de Protection et de Surete Nucleaire; Cordfunke, E H.P. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Hunterlaar, M E [Netherlands Energy Research Foundation (ECN), Petten (Netherlands)

1995-01-01

The assessment of the consequences of severe accidents in nuclear reactors involving molten core-concrete interactions (MCCls) requires estimates of the quantities and physicochemical forms of the radioactive species released from the melt into the cavity atmosphere. Such estimates in turn require a detailed knowledge of the complex chemical interactions which would occur between the fission products, fuel and the components of the core structural materials and the concrete. In recent years, effort has been put into the thermodynamic characterization of these processes. The results of such studies are important for predicting several aspects of MCCls, including: 1. The release of species by vaporization; 2. the extent of concrete penetration: a. The melt solidus and liquidus temperatures, which in turn affect the heat transfer processes and hence tile predictions of the melt temperature and the onset of solidification, b. the amounts of the solid and liquid phases and the respective compositions, which determines the viscosity of the melt, and c. the composition of the crust formed following the addition of water to quench the interaction. d. the distribution of fission products among metallic and oxidic phases. This SOAR is devoted to thermochemical calculations in the context of MCCI where most fission products and the metallic components of the melt are transferred into an oxidic form sooner or later. Calculations on fission product release from a molten pool without MCCI are underway in the source term project of the CEC-RCA. The following conditions have to be taken into account in order to be able to perform reliable thermodynamic calculations. (orig./HP).

Fission product release during MCCI. CEC nuclear safety program: MCCI project

International Nuclear Information System (INIS)

Cenerino, G.; Hunterlaar, M.E.

1995-01-01

The assessment of the consequences of severe accidents in nuclear reactors involving molten core-concrete interactions (MCCls) requires estimates of the quantities and physicochemical forms of the radioactive species released from the melt into the cavity atmosphere. Such estimates in turn require a detailed knowledge of the complex chemical interactions which would occur between the fission products, fuel and the components of the core structural materials and the concrete. In recent years, effort has been put into the thermodynamic characterization of these processes. The results of such studies are important for predicting several aspects of MCCls, including: 1. The release of species by vaporization; 2. the extent of concrete penetration: a. The melt solidus and liquidus temperatures, which in turn affect the heat transfer processes and hence tile predictions of the melt temperature and the onset of solidification, b. the amounts of the solid and liquid phases and the respective compositions, which determines the viscosity of the melt, and c. the composition of the crust formed following the addition of water to quench the interaction. d. the distribution of fission products among metallic and oxidic phases. This SOAR is devoted to thermochemical calculations in the context of MCCI where most fission products and the metallic components of the melt are transferred into an oxidic form sooner or later. Calculations on fission product release from a molten pool without MCCI are underway in the source term project of the CEC-RCA. The following conditions have to be taken into account in order to be able to perform reliable thermodynamic calculations. (orig./HP)

Data sheets of fission product release experiments for light water reactor fuel, (2)

International Nuclear Information System (INIS)

Ishiwatari, Nasumi; Nagai, Hitoshi; Takeda, Tsuneo; Yamamoto, Katsumune; Nakazaki, Chozaburo.

1979-07-01

This is the second data sheets of fission products (FP) release experiments for light water reactor fuel. Results of five FP release experiments from the third to the seventh are presented: results of pre-examinations of UO 2 pellets, photographs of parts of fuel rod assemblies for irradiation and the assemblies, operational conditions of JMTR and OWL-1, variations of radioiodine-131 level in the main loop coolant during experimental periods, and representative results of post-irradiation examinations of respective fuel rods. (author)

Technical committee meeting on evaluation of radioactive materials release and sodium fires in fast reactors

International Nuclear Information System (INIS)

1996-01-01

The objectives of the Technical Committee Meeting was to review the activities of research on radioactive materials release and sodium fires in fast reactors in each of the participating countries. It covered: out-of-pile experiments and analysis codes on source term; in-pile experiments on source term; core disruptive accidents; sodium leak experience in liquid metal fast reactors; evaluation of sodium fire; and aerosol behaviour

Technical committee meeting on evaluation of radioactive materials release and sodium fires in fast reactors

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

The objectives of the Technical Committee Meeting was to review the activities of research on radioactive materials release and sodium fires in fast reactors in each of the participating countries. It covered: out-of-pile experiments and analysis codes on source term; in-pile experiments on source term; core disruptive accidents; sodium leak experience in liquid metal fast reactors; evaluation of sodium fire; and aerosol behaviour.

Evaluation of nuclear facility decommissioning projects. Project summary report, Elk River Reactor

International Nuclear Information System (INIS)

Miller, R.L.; Adams, J.A.

1982-12-01

This report summarizes information concerning the decommissioning of the Elk River Reactor. Decommissioning data from available documents were input into a computerized data-handling system in a manner that permits specific information to be readily retrieved. The information is in a form that assists the Nuclear Regulatory Commission in its assessment of decommissioning alternatives and ALARA methods for future decommissionings projects. Samples of computer reports are included in the report. Decommissioning of other reactors, including NRC reference decommissioning studies, will be described in similar reports

QUEST2: Release 1: Project plan deliverable set

International Nuclear Information System (INIS)

Braaten, F.D.

1995-01-01

This Project Management Plan combines the project management deliverables from the P+ methodology which are applicable to Release 1 of the QUEST2 work. This consolidation reflects discussions with WHC QA regarding an appropriate method for ensuring that P+ deliverables fulfill the intent of WHC-CM-3-10 and QR-19

European lead fast reactor (ELSY and LEADER projects)

International Nuclear Information System (INIS)

Alemberti, Alessandro; Carlsson, Johan; Malambu, Edouard; Orden, Alfredo; Cinotti, Luciano; Struwe, Dankward; Agostini, Pietro; Monti, Stefano

2010-01-01

The conceptual design of the European Lead Fast Reactor is being developed starting from September 2006, in the frame of the ELSY project. The ELSY reference design is a 600 MWe pool-type reactor cooled by pure lead. The ELSY project demonstrates the possibility of designing a competitive and safe fast critical reactor using simple engineered technical features, whilst fully complying with the Generation IV goal of sustainability and minor actinide (MA) burning capability. Sustainability was a leading criterion for option selection for core design, focusing on the demonstration of the potential to be self sustaining in plutonium and to burn its own generated MAs. To this end, different core configurations have been studied. Economics was a leading criterion for primary system design and plant layout. The use of a compact and simple primary circuit with the additional objective that all internal components be removable, are among the reactor features intended to assure competitive electric energy generation and long-term investment protection. Low capital cost and construction time are pursued through simplicity and compactness of the reactor building (reduced footprint and height). The reduced plant footprint is one of the benefits coming from the elimination of the Intermediate Cooling System, the low reactor building height is the result of the design approach which foresees the adoption of short-height components and two innovative DHR systems. Among the critical issues, the impact of the large mass of lead has been carefully analyzed; it has been demonstrated that the high density of lead can be mitigated by compact solutions and adoption of seismic isolators. Safety has been one of the major focuses all over the ELSY development. In addition to the inherent safety advantages of lead coolant (high boiling point and no exothermic reactions with air or water) a high safety grade of the overall system has been reached. In fact the overall primary system has been

Overview of the OECD-Halden reactor project

International Nuclear Information System (INIS)

Vitanza, Carlo

2001-01-01

The OECD Halden Reactor Project is an international network dedicated to enhanced safety and reliability of nuclear power plants. The Project operates under the auspices of the OECD Nuclear Energy Agency and aims at addressing and resolving issues relevant to safety as they emerge in the nuclear community. This paper gives a concise presentation of the Project goals and of its technical infrastructure. The paper contains also a brief overview of results from the programme carried out in the time period 1997-1999 and of the main issues contemplated for the 3-year programme period 2000-2002

Ex-vessel coolability and energetics of steam explosions in nordic light water reactors - EXCOOLSE project report 2004

International Nuclear Information System (INIS)

Park, H.S.; Nayak, A.K.; Hansson, R.C.; Sehgal, B.R.

2005-10-01

Beyond-the-design-basis accidents, i.e. severe accidents, involve melting of the nuclear reactor core and release of radioactivity. Intensive research has been performed for years to evaluate the consequence of the postulated severe accidents. Severe accidents posed, to the reactor researchers, a most interesting and most difficult set of phenomena to understand, and to predict the consequences, for the various scenarios that could be contemplated. The complexity of the interactions, occurring at such high temperatures (∼ 2500 deg. C), between different materials, which are changing phases and undergoing chemical reactions, is simply indescribable with the accuracy that one may desire. Thus, it is a wise approach to pursue research on SA phenomena until the remaining uncertainty in the predicted consequence, or the residual risk, can be tolerated. In the PRE-DELI-MELT project at NKS, several critical issues on the core melt loadings in the BWR and PWR reactor containments were identified. Many of Nordic nuclear power plants, particularly in boiling water reactors, adopted the Severe Accident Management Strategy (SAMS) which employed the deep subcooled water pool in lower dry-well. The success of this SAMS largely depends on the issues of steam explosions and formation of debris bed and its coolability. From the suggestions of the PRE-DELI-MELT project, a series of research plan was proposed to investigate the remaining issues specifically on the ex-vessel coolability of corium during severe accidents; (a) ex-vessel coolability of the melt or particulate debris, and (b) energetics and debris characteristics of fuel-coolant interactions endangering the integrity of the reactor containments. (au)

Ex-vessel coolability and energetics of steam explosions in nordic light water reactors - EXCOOLSE project report 2004

Energy Technology Data Exchange (ETDEWEB)

Park, H.S.; Nayak, A.K.; Hansson, R.C.; Sehgal, B.R. [Royal Inst. of Technology, Div. of Nuclear Power Safety (Sweden)

2005-10-01

Beyond-the-design-basis accidents, i.e. severe accidents, involve melting of the nuclear reactor core and release of radioactivity. Intensive research has been performed for years to evaluate the consequence of the postulated severe accidents. Severe accidents posed, to the reactor researchers, a most interesting and most difficult set of phenomena to understand, and to predict the consequences, for the various scenarios that could be contemplated. The complexity of the interactions, occurring at such high temperatures ({approx} 2500 deg. C), between different materials, which are changing phases and undergoing chemical reactions, is simply indescribable with the accuracy that one may desire. Thus, it is a wise approach to pursue research on SA phenomena until the remaining uncertainty in the predicted consequence, or the residual risk, can be tolerated. In the PRE-DELI-MELT project at NKS, several critical issues on the core melt loadings in the BWR and PWR reactor containments were identified. Many of Nordic nuclear power plants, particularly in boiling water reactors, adopted the Severe Accident Management Strategy (SAMS) which employed the deep subcooled water pool in lower dry-well. The success of this SAMS largely depends on the issues of steam explosions and formation of debris bed and its coolability. From the suggestions of the PRE-DELI-MELT project, a series of research plan was proposed to investigate the remaining issues specifically on the ex-vessel coolability of corium during severe accidents; (a) ex-vessel coolability of the melt or particulate debris, and (b) energetics and debris characteristics of fuel-coolant interactions endangering the integrity of the reactor containments. (au)

Calculation of releases of radioactive materials in gaseous and liquid effluents from boiling water reactors (BWR-GALE Code)

International Nuclear Information System (INIS)

Bangart, R.L.; Bell, L.G.; Boegli, J.S.; Burke, W.C.; Lee, J.Y.; Minns, J.L.; Stoddart, P.G.; Weller, R.A.; Collins, J.T.

1978-12-01

The calculational procedures described in the report reflect current NRC staff practice. The methods described will be used in the evaluation of applications for construction permits and operating licenses docketed after January 1, 1979, until this NUREG is revised as a result of additional staff review. The BWR-GALE (Boiling Water Reactor Gaseous and Liquid Effluents) Code is a computerized mathematical model for calculating the release of radioactive material in gaseous and liquid effluents from boiling water reactors (BWRs). The calculations are based on data generated from operating reactors, field tests, laboratory tests, and plant-specific design considerations incorporated to reduce the quantity of radioactive materials that may be released to the environment

Selected power reactor projects in Canada and the United States of America

Energy Technology Data Exchange (ETDEWEB)

NONE

1964-11-01

As part of its activities in connection with the development of nuclear power, the IAEA has undertaken a continuing study of the technology and economics of power reactors, with particular reference to the needs of the developing countries. Information on the progress made in eight power reactor projects, namely those of Bonus, Pathfinder, Elk River, Piqua, Hallam, Experimental Gas-Cooled Reactor (EGCR), High-Temperature Gas-Cooled Reactor (HTGCR) and Nuclear Power Demonstration (NPD), is presented in this report. Developments during the past year are shown, emphasis being placed on operating experience in the case of those reactors which have become critical. The Agency is grateful to the Governments of Canada and the USA, who have extended the necessary facilities for covering he different power reactor projects in their respective countries. The cooperation received from the reactor manufacturers, builders and operators is also gratefully acknowledged. It is hoped that this report will be of interest to reactor technologists and operators and those interested in the application of nuclear power.

Selected power reactor projects in Canada and the United States of America

International Nuclear Information System (INIS)

1964-01-01

As part of its activities in connection with the development of nuclear power, the IAEA has undertaken a continuing study of the technology and economics of power reactors, with particular reference to the needs of the developing countries. Information on the progress made in eight power reactor projects, namely those of Bonus, Pathfinder, Elk River, Piqua, Hallam, Experimental Gas-Cooled Reactor (EGCR), High-Temperature Gas-Cooled Reactor (HTGCR) and Nuclear Power Demonstration (NPD), is presented in this report. Developments during the past year are shown, emphasis being placed on operating experience in the case of those reactors which have become critical. The Agency is grateful to the Governments of Canada and the USA, who have extended the necessary facilities for covering he different power reactor projects in their respective countries. The cooperation received from the reactor manufacturers, builders and operators is also gratefully acknowledged. It is hoped that this report will be of interest to reactor technologists and operators and those interested in the application of nuclear power

EC-funded project (HTR-L) for the definition of a European safety approach for HTR's

International Nuclear Information System (INIS)

Ehster, S.; Dominguez, M.T.; Coe, I.; Brinkmann, G.; Lensa, W. von; Mheen, W. van der; Alessandroni, C.; Pirson, J.

2002-01-01

The inherent safety features of the HTRs make events leading to severe core damage highly unlikely and constitute the main differentiating aspects compared to LWRs. While a known and stable regulatory environment has long been established for Light Water Reactors, a different approach is necessary for the licensing of HTR based power plants. Among the R and D projects funded by the European Commission for HTR reactors, the HTR-L project is dedicated to the definition of a common and coherent European safety approach and the identification of the main licensing issues for the licensing framework of the Modular HTRs. Other specific objectives of this project are : To develop a methodology to classify the accidental conditions; To define the preliminary requirements for the confinement of radioactive products and to assess the need for a 'conventional' containment structure; To establish a SSC (2) classification and to define the rules for equipment qualification; To identify the key issues that need to be addressed in the licensing process of the HTRs; To organize a workshop with the concerned Safety Authorities at the end of the project. This paper will explain the project objectives and its final expected outcomes. (author)

Characteristics of D-3He fueled frc reactor: ARTEMIS-L

International Nuclear Information System (INIS)

Momota, H.; Motojima, O.; Okamoto, M.; Sudo, S.; Tomita, Y.; Yamaguchi, S.; Iiyoshi, A.; Onozuka, M.; Ohnishi, M.; Uenosono, C.

1993-11-01

The paper introduces briefly the scenario and discuss the attractive characteristics of D-3He fueled commercial fusion reactor ARTEMIS-L. By using favorable characteristics of a field-reversed configuration, the fusion plasma of ARTEMIS-L is compact and its beta-value is extremely high. One find consequently a possibility of constructing an economical fusion power power plant on this prospect. The life of the structural materials is sound during the full reactor life (30 years) and the safety of the reactor is intrinsic to D-3He fuels. The amount of disposed materials is rather small and the level of these intruder dose is so low that the plant appears to be acceptable in view of the environment. (author)

The SCAR project - accidental thermal-hydraulics: from the simulation to the simulators

International Nuclear Information System (INIS)

Farvacque, M.; Faydide, B.; Parent, M.; Iffenecker, F.; Pentori, B.; Dumas, J.M.

2000-01-01

The integration of the CATHARE code in the reactor simulators was completed in the beginning of the years 1990 with the design of the simulators SIPA1 and SIPA2. The SCAR project (Simulator CAthare Release), presented in this paper, is the following of this application. The objective is the adaptation of a reference CATHARE code version to the simulators environment, in order to realize the convergence between the safety analysis tool and the simulator. (A.L.B.)

IRPhE-DRAGON-DPR, OECD High Temperature Reactor Dragon Project, Primary Documents

International Nuclear Information System (INIS)

2004-01-01

Description: The DRAGON Reactor Experiment (DRE): The first demonstration High temperature gas reactor (HTGR) was built in the 1960's. Thirteen OECD countries began a project in 1959 to build an experimental reactor known as Dragon at Winfrith in the UK. The reactor - which operated successfully between 1966 and 1975 - had a thermal output of 20 MW and achieved a gas outlet temperature of 750 deg. C. The High Temperature Reactor concept, if it justified its expectations, was seen as having its place as an advanced thermal reactor between the current thermal reactor types such as the PWR, BWR, and AGR and the sodium cooled fast breeder reactor. It was expected that the HTR would offer better thermal efficiency, better uranium utilisation, either with low enriched uranium fuel or high enriched uranium thorium fuel, better inherent safety and lower unit power costs. In the event all these potential advantages were demonstrated to be in principle achievable. This view is still shared today. In fact Very High Temperature Reactors is one of the concepts retained for Generation IV. Projects on constructing Modular Pebble Bed Reactors are under way. Here all available Dragon Project Reports (DPR) - approximately 1000 - are collected in electronic form. An index points to the reports (PDF format); each table in the report is accessible in EXCEL format with the aim of facilitating access to the data. These reports describe the design, experiments and modelling carried out over a period of 17 years. 2 - Related or auxiliary information: IRPHE-HTR-ARCH-01, Archive of HTR Primary Documents NEA-1728/01. 3 - Software requirements: Acrobat Reader, Microsoft Word, HTML Browser required

Fission product release assessment for end fitting failure in Candu reactor loaded with CANFLEX-NU fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Oh, Dirk Joo; Jeong, Chang Joon; Lee, Kang Moon; Suk, Ho Chun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1998-12-31

Fission product release (FPR) assessment for End Fitting Failure (EFF) in CANDU reactor loaded with CANFLEX-natural uranium (NU) fuel bundles has been performed. The predicted results are compared with those for the reactor loaded with standard 37-element bundles. The total channel I-131 release at the end of transient for EFF accident is calculated to be 380.8 TBq and 602.9 TBq for the CANFLEX bundle and standard bundle channel cases, respectively. They are 4.9% and 7.9% of total inventory, respectively. The lower total releases of the CANFLEX bundle O6 channel are attributed to the lower initial fuel temperatures caused by the lower linear element power of the CANFLEX bundle compared with the standard bundle. 4 refs., 1 fig., 4 tabs. (Author)

Fission product release assessment for end fitting failure in Candu reactor loaded with CANFLEX-NU fuel bundles

Energy Technology Data Exchange (ETDEWEB)

Oh, Dirk Joo; Jeong, Chang Joon; Lee, Kang Moon; Suk, Ho Chun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1997-12-31

Fission product release (FPR) assessment for End Fitting Failure (EFF) in CANDU reactor loaded with CANFLEX-natural uranium (NU) fuel bundles has been performed. The predicted results are compared with those for the reactor loaded with standard 37-element bundles. The total channel I-131 release at the end of transient for EFF accident is calculated to be 380.8 TBq and 602.9 TBq for the CANFLEX bundle and standard bundle channel cases, respectively. They are 4.9% and 7.9% of total inventory, respectively. The lower total releases of the CANFLEX bundle O6 channel are attributed to the lower initial fuel temperatures caused by the lower linear element power of the CANFLEX bundle compared with the standard bundle. 4 refs., 1 fig., 4 tabs. (Author)

Secret high-temperature reactor concept for inertial fusion

International Nuclear Information System (INIS)

Monsler, M.J.; Meier, W.R.

1983-01-01

The goal of our SCEPTRE project was to create an advanced second-generation inertial fusion reactor that offers the potential for either of the following: (1) generating electricity at 50% efficiency, (2) providing high temperature heat (850 0 C) for hydrogen production, or (3) producing fissile fuel for light-water reactors. We have found that these applications are conceptually feasible with a reactor that is intrinsically free of the hazards of catastrophic fire or tritium release

Uncertainty estimates for predictions of the impact of breeder-reactor radionuclide releases

International Nuclear Information System (INIS)

Miller, C.W.; Little, C.A.

1982-01-01

This paper summarizes estimates, compiled in a larger report, of the uncertainty associated with models and parameters used to assess the impact on man radionuclide releases to the environment by breeder reactor facilities. These estimates indicate that, for many sites, generic models and representative parameter values may reasonably be used to calculate doses from annual average radionuclide releases when these calculated doses are on the order of one-tenth or less of a relevant dose limit. For short-term, accidental releases, the uncertainty in the dose calculations may be much larger than an order of magnitude. As a result, it may be necessary to incorporate site-specific information into the dose calculation under such circumstances. However, even using site-specific information, inherent natural variability within human receptors, and the uncertainties in the dose conversion factor will likely result in an overall uncertainty of greater than an order of magnitude for predictions of dose following short-term releases

Reactor Materials Program probability of indirectly--induced failure of L and P reactor process water piping

International Nuclear Information System (INIS)

Daugherty, W.L.

1988-01-01

The design basis accident for the Savannah River Production Reactors is the abrupt double-ended guillotine break (DEGB) of a large process water pipe. This accident is not considered credible in light of the low applied stresses and the inherent ductility of the piping material. The Reactor Materials Program was initiated to provide the technical basis for an alternate credible design basis accident. One aspect of this work is to determine the probability of the DEGB; to show that in addition to being incredible, it is also highly improbable. The probability of a DEGB is broken into two parts: failure by direct means, and indirectly-induced failure. Failure of the piping by direct means can only be postulated to occur if an undetected crack grows to the point of instability, causing a large pipe break. While this accident is not as severe as a DEGB, it provides a conservative upper bound on the probability of a direct DEGB of the piping. The second part of this evaluation calculates the probability of piping failure by indirect causes. Indirect failure of the piping can be triggered by an earthquake which causes other reactor components or the reactor building to fall on the piping or pull it from its supports. Since indirectly-induced failure of the piping will not always produce consequences as severe as a DEGB, this gives a conservative estimate of the probability of an indirectly- induced DEGB. This second part, indirectly-induced pipe failure, is the subject of this report. Failure by seismic loads in the piping itself will be covered in a separate report on failure by direct causes. This report provides a detailed evaluation of L reactor. A walkdown of P reactor and an analysis of the P reactor building provide the basis for extending the L reactor results to P reactor

Calculation of burnup and power dependence on fission gas released from PWR type reactor fuel element

International Nuclear Information System (INIS)

Edy-Sulistyono

1996-01-01

Burn up dependence of fission gas released and variation power analysis have been conducted using FEMXI-IV computer code program for Pressure Water Reactor Fuel During steady-state condition. The analysis result shows that the fission gas release is sensitive to the fuel temperature, the increasing of burn up and power in the fuel element under irradiation experiment

V L Ginzburg and the Atomic Project

Science.gov (United States)

Ritus, V. I.

2017-04-01

This paper is an expanded version of the author's talk presented at a session of the Physical Sciences Division of the Russian Academy of Sciences celebrating the 100th anniversary of V L Ginzburg's birth. Tamm's Special group was organized in June 1948 with the task to clarify the feasibility of constructing a hydrogen bomb. Having verified and confirmed the calculated results by Ya B Zel'dovich's group, the Tamm group proposed an original hydrogen bomb design, which, following A D Sakharov's idea, consisted of an atomic bomb surrounded spherically by nested uranium and heavy water layers: the heavy water, on V L Ginzburg's suggestion, was replaced by higher-calorie solid lithium-6 deuteride. The ionization implosion of deuterium by uranium, both heated by the atomic bomb's explosion, greatly accelerates nuclear reactions in deuterium and uranium and increases the total energy release. Upon their approval by the KB-11 top researchers, the Atomic project leadership, and the government, the proposals were implemented in the RDS-6s bomb, which was successfully tested on 12 August 1953. Lithium-6 deuteride turned out to be a convenient multipurpose nuclear fuel. The paper highlights the recognition by the leaders of the country and of the Atomic project that fundamental science plays a crucial role in promoting scientists' ideas and proposals.

Research projects at the TRIGA-reactor Vienna

International Nuclear Information System (INIS)

Boeck, H.; Buchberger, T.; Buchtela, K.; Hammer, J.; Miksovsky, A.; Veider, A.; Weber, H.W.; Zugarek, G.

1986-01-01

In 1985 the thermalizing column was modified to a beam tube with a conical collimator for neutron radiography. A highly sophisticated sample and cassette changer will be constructed in the next months. The central channel of the thermal column is also used for neutron radiography especially for small objects. The four beam tubes of the TRIGA-reactor are intensively used for neutron spectroscopy, small angle scattering, neutron interferometry and investigations of magnetic structures with polarized neutrons. The neutron activation installation in the piecing beam tube is permanently used for various sample analysis using a ultrafast pneumatic transfer system. In addition to these experiments directly related to the TRIGA-reactor other research projects are carried out, some of them under an IAEA research contract which are mostly focused towards nuclear safeguards such as the magnetic scanning of power reactor fuel assemblies or the laser surveillance system of spent fuel pools. (author)

INTEGRAL BENCHMARKS AVAILABLE THROUGH THE INTERNATIONAL REACTOR PHYSICS EXPERIMENT EVALUATION PROJECT AND THE INTERNATIONAL CRITICALITY SAFETY BENCHMARK EVALUATION PROJECT

Energy Technology Data Exchange (ETDEWEB)

J. Blair Briggs; Lori Scott; Enrico Sartori; Yolanda Rugama

2008-09-01

Interest in high-quality integral benchmark data is increasing as efforts to quantify and reduce calculational uncertainties accelerate to meet the demands of next generation reactor and advanced fuel cycle concepts. The International Reactor Physics Experiment Evaluation Project (IRPhEP) and the International Criticality Safety Benchmark Evaluation Project (ICSBEP) continue to expand their efforts and broaden their scope to identify, evaluate, and provide integral benchmark data for method and data validation. Benchmark model specifications provided by these two projects are used heavily by the international reactor physics, nuclear data, and criticality safety communities. Thus far, 14 countries have contributed to the IRPhEP, and 20 have contributed to the ICSBEP. The status of the IRPhEP and ICSBEP is discussed in this paper, and the future of the two projects is outlined and discussed. Selected benchmarks that have been added to the IRPhEP and ICSBEP handbooks since PHYSOR’06 are highlighted, and the future of the two projects is discussed.

INTEGRAL BENCHMARKS AVAILABLE THROUGH THE INTERNATIONAL REACTOR PHYSICS EXPERIMENT EVALUATION PROJECT AND THE INTERNATIONAL CRITICALITY SAFETY BENCHMARK EVALUATION PROJECT

International Nuclear Information System (INIS)

J. Blair Briggs; Lori Scott; Enrico Sartori; Yolanda Rugama

2008-01-01

Interest in high-quality integral benchmark data is increasing as efforts to quantify and reduce calculational uncertainties accelerate to meet the demands of next generation reactor and advanced fuel cycle concepts. The International Reactor Physics Experiment Evaluation Project (IRPhEP) and the International Criticality Safety Benchmark Evaluation Project (ICSBEP) continue to expand their efforts and broaden their scope to identify, evaluate, and provide integral benchmark data for method and data validation. Benchmark model specifications provided by these two projects are used heavily by the international reactor physics, nuclear data, and criticality safety communities. Thus far, 14 countries have contributed to the IRPhEP, and 20 have contributed to the ICSBEP. The status of the IRPhEP and ICSBEP is discussed in this paper, and the future of the two projects is outlined and discussed. Selected benchmarks that have been added to the IRPhEP and ICSBEP handbooks since PHYSOR-06 are highlighted, and the future of the two projects is discussed

International project on innovative nuclear reactors and fuel cycles

International Nuclear Information System (INIS)

Cherepnin, Yu.S.; Bezzubtsev, V.S.; Gabaraev, B.A.

2002-01-01

Positive changes are currently taking place in nuclear power in the world. Power generation at Nuclear Power Plants (NPPs) is increasing and new units construction and completion rates are growing in some of leading countries. Considerable efforts are made for improving the safety of operating NPPs, effective use of nuclear fuel and solving the spent nuclear fuel and radioactive waste problems. Simultaneously, work are undertaken to develop new reactor technologies to reduce the fundamental drawbacks of conventional nuclear power, namely: insufficient safety, spent fuel and waste handling problems, nuclear material proliferation risk and poor economic competitiveness as compared to fossil-fuel energy sources. One the most important events in this field is an international project implemented by three agencies (OECD-IEA, OECD-NEA, IAEA) for comparative evaluation of new projects, development of Generation IV reactors underway in the US in cooperation with a number of Western countries and, finally, the initiative by Russian President V.V. Putin for consolidation the efforts of interested countries under auspices of IAEA to solve the problem of energy support for sustainable development of humankind, radical solution of non-proliferation problems and environmental sanitation of the Planet of Earth. The 44-th General Conference of IAEA in September 2000 supported the Initiative of Russian President and called all interested countries to unite efforts under the Agency's auspices in the International Project on Innovative Nuclear Reactors and Fuel Cycles to consider and select the most acceptable nuclear technologies of the 21-st century with regard for the drawbacks of today's nuclear power. Main objectivities of INPRO: Promotion of the availability of nuclear power for sustainable satisfaction of the energy needs in 21-st century; Consolidation of efforts by all interested INPRO participating countries (both owners and users of technologies) for joint development of

Behaviour of heavy water in nuclear reactors of the CEA; Comportement de l'eau lourde dans les piles du C.E.A

Energy Technology Data Exchange (ETDEWEB)

Chenouard, J; Dirian, G; Roth, E [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

In the two heavy water reactors of the CEA: Zoe and P-2, we do: A) the supervision of the isotopic composition of the heavy water; B) the supervision of gases released by the decomposition of the heavy water under radiation, and to their recombination; C) periodic analyses of impurities. (M.B.) [French] Dans les deux piles a eau lourde du Commissariat a l'Energie Atomique: Zoe et P 2, nous effectuons: A) la surveillance de la composition isotopique de l'eau lourde; B) la surveillance des gaz degages par la decomposition de l'eau lourde sous radiation, et a leur recombinaison; C) des analyses periodiques d'impuretes. (M.B.)

ORNL experiments to characterize fuel release from the reactor primary containment in severe LMFBR accidents

International Nuclear Information System (INIS)

Wright, A.L.; Kress, T.S.; Smith, A.M.

1980-01-01

This paper presents results from aerosol source term experiments performed in the ORNL Aerosol Release and Transport (ART) Program sponsored by the US NRC. The tests described were performed to provide information on fuel release from an LMFBR primary containment as a result of a hypothetical core-disruptive accident (HCDA). The release path investigated in these tests assumes that a fuel/sodium bubble is formed after disassembly that transports fuel and fission products through the sodium coolant and cover gas to be relased into the reactor secondary containment. Due to the excellent heat transfer characteristics of the sodium, there is potential for large attenuation of the maximum release

Project accent: graphite irradiated creep in a materials test reactor

International Nuclear Information System (INIS)

Brooking, M.

2014-01-01

Atkins manages a pioneering programme of irradiation experiments for EDF Energy. One of these projects is Project ACCENT, designed to obtain evidence of a beneficial physical property of the graphite, which may extend the life of the Advanced Gas-cooled Reactors (AGRs). The project team combines the in-house experience of EDF Energy with two supplier organisations (providing the material test reactors and testing facilities) and supporting consultancies (Atkins and an independent technical expert). This paper describes: - Brief summary of the Project; - Discussion of the challenges faced by the Project; and - Conclusion elaborating on the aims of the Project. These challenging experiments use bespoke technology and both un-irradiated (virgin) and irradiated AGR graphite. The results will help to better understand graphite irradiation-induced creep (or stress modified dimensional change) properties and therefore more accurately determine lifetime and safe operating envelopes of the AGRs. The first round of irradiation has been completed, with a second round about to commence. This is a key step to realising the full lifetime ambition for AGRs, demonstrating the relaxation of stresses within the graphite bricks. (authors)

Radionuclide distribution in TMI-2 reactor building basement liquids and solids

International Nuclear Information System (INIS)

Horan, J.T.; McIsaac, C.V.; Keefer, D.G.

1984-01-01

As a result of the TMI-2 accident, approximately 2.46 x 10 6 L of contaminated water were released to the Reactor Building basement. The principal fission product release pathway from the damaged core was through the reactor coolant system (RCS) to the pressurizer, through the pressure-operated relief valve (PORV) on the pressurizer to the Reactor Coolant Drain Tank (RCDT), and then through the RCDT rupture disk to the Reactor Building basement. Since August 1979, a number of efforts have been made to determine the location, quantity, and composition of fission products released to the Reactor Building basement. These efforts have included sampling of the basement water and solids, the basement sump pump recirculation line, the RCDT, and visual surveys using a closed circuit television (CCTV) system. The analysis of basement samples has provided data on the physical and radioisotopic characteristics of the liquids and solids. This paper describes the sample collection techniques and discusses radiochemical analyses results

Halden Reactor Project activities, achievements and international collaboration

International Nuclear Information System (INIS)

Wiesenack, W.

2003-01-01

This paper concentrates on the Halden Project research programme related to fuel testing. An overview of ongoing tests on WWER fuel performance is also included. The ongoing and planned experiments containing WWER-related fuels and materials - Irradiation of Standard and Modified WWER Fuel (IFA-503) and Corrosion Testing of Different Cladding Alloys (IFA-638) - are presented. The future experiments involving WWER fuel and cladding types foreseen in of the Halden Reactor Project programme are given

Decontamination and dismantlement of the JANUS Reactor at Argonne National Laboratory-East. Project final report

International Nuclear Information System (INIS)

Fellhauer, C.R.; Clark, F.R.

1997-10-01

The decontamination and dismantlement of the JANUS Reactor at Argonne National Laboratory-East (ANL-E) was completed in October 1997. Descriptions and evaluations of the activities performed and analyses of the results obtained during the JANUS D and D Project are provided in this Final Report. The following information is included: objective of the JANUS D and D Project; history of the JANUS Reactor facility; description of the ANL-E site and the JANUS Reactor facility; overview of the D and D activities performed; description of the project planning and engineering; description of the D and D operations; summary of the final status of the JANUS Reactor facility based upon the final survey results; description of the health and safety aspects of the project, including personnel exposure and OSHA reporting; summary of the waste minimization techniques utilized and total waste generated by the project; and summary of the final cost and schedule for the JANUS D and D Project

A model for the release, dispersion and environmental impact of a postulated reactor accident from a submerged commercial nuclear power plant

Science.gov (United States)

Bertch, Timothy Creston

1998-12-01

Nuclear power plants are inherently suitable for submerged applications and could provide power to the shore power grid or support future underwater applications. The technology exists today and the construction of a submerged commercial nuclear power plant may become desirable. A submerged reactor is safer to humans because the infinite supply of water for heat removal, particulate retention in the water column, sedimentation to the ocean floor and inherent shielding of the aquatic environment would significantly mitigate the effects of a reactor accident. A better understanding of reactor operation in this new environment is required to quantify the radioecological impact and to determine the suitability of this concept. The impact of release to the environment from a severe reactor accident is a new aspect of the field of marine radioecology. Current efforts have been centered on radioecological impacts of nuclear waste disposal, nuclear weapons testing fallout and shore nuclear plant discharges. This dissertation examines the environmental impact of a severe reactor accident in a submerged commercial nuclear power plant, modeling a postulated site on the Atlantic continental shelf adjacent to the United States. This effort models the effects of geography, decay, particle transport/dispersion, bioaccumulation and elimination with associated dose commitment. The use of a source term equivalent to the release from Chernobyl allows comparison between the impacts of that accident and the postulated submerged commercial reactor plant accident. All input parameters are evaluated using sensitivity analysis. The effect of the release on marine biota is determined. Study of the pathways to humans from gaseous radionuclides, consumption of contaminated marine biota and direct exposure as contaminated water reaches the shoreline is conducted. The model developed by this effort predicts a significant mitigation of the radioecological impact of the reactor accident release

Project based learning for reactor engineering education

International Nuclear Information System (INIS)

Narabayashi, Tadashi; Tsuji, Masashi; Shimazu, Yoichiro

2009-01-01

Trial in education of nuclear engineering in Hokkaido University has proved to be quite attractive for students. It is an education system called Project Based Learning (PBL), which is not based on education by lecture only but based mostly on practice of students in the classroom. The system was adopted four years ago. In the actual class, we separated the student into several groups of the size about 6 students. In the beginning of each class room time, a brief explanations of the related theory or technical bases. Then the students discuss in their own group how to precede their design calculations and do the required calculation and evaluation. The target reactor type of each group was selected by the group members for themselves at the beginning of the semester as the first step of the project. The reactor types range from a small in house type to that for a nuclear ship. At the end of the semester, each group presents the final design. The presentation experience gives students a kind of fresh sensation. Nowadays the evaluation results of the subject by the students rank in the highest in the faculty of engineering. Based on the considerations above, we designed the framework of our PBL for reactor engineering. In this paper, we will present some lessons learned in this PBL education system from the educational points of view. The PBL education program is supported by IAE/METI in Japan for Nuclear Engineering Education. (author)

ARCHER Project: Progress on Material and component activities for the Advanced High Temperature Reactor

International Nuclear Information System (INIS)

Buckthorpe, D.E.

2014-01-01

The ARCHER (Advanced High-Temperature Reactors for Cogeneration of Heat and Electricity R&D) integrated project is a four year project which was started in 2011 as part of the European Commission 7th Framework Programme (FP7) to perform High Temperature Reactor technology R&D in support of reactor demonstration. The project consortium encompasses conventional and Nuclear Industry, Utilities, Technical Support Organizations, Research & Development Organizations and Academia. The activities involved contribute to the Generation IV (GIF) International Forum and collaborate with related projects in the US, China, Japan, and the Republic of Korea in cooperation with IAEA and ISTC. This paper addresses the progress of the work on ARCHER materials and component activities since the start of the project and underlines some of the main conclusions reached. (author)

Operational readiness reviews for restart of L reactor

International Nuclear Information System (INIS)

Finley, R.H.

1984-01-01

The L Reactor at the Savannah River Plant is being restarted after being in a standby status since 1968. Operational Readiness Reviews (ORRs) were conducted by DOE-SR and contractor personnel concurrent with the restart activity. This paper summarizes the ORR activity

Characteristics of D-{sup 3}He fueled frc reactor: ARTEMIS-L

Energy Technology Data Exchange (ETDEWEB)

Momota, H.; Motojima, O.; Okamoto, M.; Sudo, S.; Tomita, Y.; Yamaguchi, S.; Iiyoshi, A.; Onozuka, M.; Ohnishi, M.; Uenosono, C.

1993-11-01

The paper introduces briefly the scenario and discuss the attractive characteristics of D-3He fueled commercial fusion reactor ARTEMIS-L. By using favorable characteristics of a field-reversed configuration, the fusion plasma of ARTEMIS-L is compact and its beta-value is extremely high. One find consequently a possibility of constructing an economical fusion power power plant on this prospect. The life of the structural materials is sound during the full reactor life (30 years) and the safety of the reactor is intrinsic to D-3He fuels. The amount of disposed materials is rather small and the level of these intruder dose is so low that the plant appears to be acceptable in view of the environment. (author).

Production and release of {sup 14}C from a swimming pool reactor

Energy Technology Data Exchange (ETDEWEB)

Krishnamoorthy, T M [Bhabha Atomic Research Centre, Mumbai (India). Environmental Assessment Div.; Sadarangani, S H [Bhabha Atomic Research Centre, Mumbai (India). Radiation Safety Systems Div.; Doshi, G R [Bhabha Atomic Research Centre, Bombay (India). Health Physics Div.

1994-04-01

The annual production rate of {sup 14}C in the Apsara swimming pool reactor works out to be about 2.94 mCi. The concentration distribution of {sup 14}C in different compartments viz. pool water, reactor hall air and ion-exchange resin ranged from 200 to 440 pCi/l, 0.09 to 0.38 pCi/l, an average concentration of 8.16 pCi/g respectively. The mean residence time of {sup 14}C in pool water is evaluated to be about 7 days taking into account various sinks. The study revealed atmospheric exchange at the air-water interface as the dominant process responsible for the loss of {sup 14}C from the pool water. (author). 7 refs., 2 figs., 4 tabs.

105-B Reactor museum feasibility assessment (Phase 2) project

International Nuclear Information System (INIS)

Heckel, R. P.

2000-01-01

This 105-B Reactor Museum feasibility assessment project report documents project activities that have been performed, including a review and assessment of previously existing information, a walk-through of the facility, an assessment of potential hazards, and selection of mitigative measures deemed to be appropriate to allow unescorted access by members of the public to a specified primary tour route

Halden reactor project

International Nuclear Information System (INIS)

1981-01-01

Accomplishments realized during 1981 are summarized in this report. Reactor safety considerations continue to be the prime motivation for the Halden fuel programme. A major part of the experimental efforts deal with effects of loss-of-coolant accidents (LOCA) on fuel thermal and dimensional response. Fuel defect mechanisms and probabilities, both during safety related accident sequences and in response to operational transients, are also extensively studied. The programme encompasses current fuel designs as well as design modifications expected to improve performance. The Halden Project is expanding its work on process computer applications with emphasis on operator-process communication and operator guidance systems. This includes human factors experiments, control room layout and design, alarm handling systems and core surveillance. The principal tool being developed for performing realistic experiments in this field is the new control room with a full scope training simulator model of a nuclear power plant

Activities of research-reactor-technology project in FNCA from FY2005 to FY2007. Sharing neutronics calculation technique for core management and utilization of research reactors

International Nuclear Information System (INIS)

2010-07-01

RRT project (Research-Reactor-Technology Project) was carried out with the theme of 'sharing neutronics calculation technique for core management and utilization of research reactors' in the framework of FNCA (Forum for Nuclear Cooperation in Asia) from FY2005 to FY2007. The objective of the project was to improve and equalize the level of neutronics calculation technique for the reactor core management among participating countries to assure the safe and stable operation of research reactors and the promotion of the effective utilization. Neutronics calculation codes, namely SRAC code system and MVP code, were adopted as common codes. Participating countries succeeded in applying the common codes to analyzing the core of each domestic research reactor. Some participating countries succeeded in applying the common codes to analyzing for utilization of own research reactors. Activities of RRT project have improved and equalized the level of neutronics calculation technique among participating countries. (author)

Application of the dose limitation system to the control of carbon-14 releases from heavy-water-moderated reactors

International Nuclear Information System (INIS)

Beninson, D.; Gonzalez, A.J.

1982-01-01

Heavy-water-moderated reactors produce substantially more carbon-14 than light-water reactors. Applying the principles of the systems of dose limitation, the paper presents the rationale used for establishing the release limit for effluents containing this nuclide and for the decisions made regarding the effluent treatment in the third nuclear power station in Argentina. Production of carbon-14 in PHWR and the release routes are analysed in the light of the different effluent treatment possibilities. An optimization assessment is presented, taking into account effluent treatment and waste management costs, and the collective effective dose commitment due to the releases. The contribution of present carbon-14 releases to future individual doses is also analysed in the light of an upper bound for the contribution, representing a fraction of the individual dose limits. The paper presents the resulting requirements for the effluent treatment regarding carbon-14 and the corresponding regulatory aspects used in Argentina. (author)

Review of Halden Reactor Project high burnup fuel data that can be used in safety analyses

International Nuclear Information System (INIS)

Wiesenack, W.

1996-01-01

The fuels and materials testing programmes carried out at the OECD Halden Reactor Project are aimed at providing data in support of a mechanistic understanding of phenomena, especially as related to high burnup fuel. The investigations are focused on identifying long term property changes, and irradiation techniques and instrumentation have been developed over the years which enable to assess fuel behaviour and properties in-pile. The fuel-cladding gap has an influence on both thermal and mechanical behaviour. Improved gap conductance due to gap closure at high exposure is observed even in the case of a strong contamination with released fission gas. On the other hand, pellet-cladding mechanical interaction, which is measured with cladding elongation detectors and diameter gauges, is re-established after a phase with less interaction and is increasing. These developments are exemplified with data showing changes of fuel temperature, hydraulic diameter and cladding elongation with burnup. Fuel swelling and cladding primary and secondary creep have been successfully measured in-pile. They provide data for, e.g., the possible cladding lift-off to be accounted for at high burnup. Fuel conductivity degradation is observed as a gradual temperature increase with burnup. This affects stored heat, fission gas release and temperature dependent fuel behaviour in general. The Halden Project's data base on fission gas release shows that the phenomenon is associated with an accumulation of gas atoms at the grain boundaries to a critical concentration before appreciable release occurs. This is accompanied by an increase of the surface-to-volume ratio measured in-pile in gas flow experiments. A typical observation at high burnup is also that a burst release of fission gas may occur during a power decrease. Gas flow and pressure equilibration experiments have shown that axial communication is severely restricted at high burnup

Fission product release from defected nuclear reactor fuel elements

International Nuclear Information System (INIS)

Lewis, B.J.

1983-01-01

The release of gaseous (krypton and xenon) and iodine radioactive fission products from defective fuel elements is described with a semi-empirical model. The model assumes precursor-corrected 'Booth diffusional release' in the UO 2 and subsequent holdup in the fuel-to-sheath gap. Transport in the gap is separately modelled with a phenomenological rate constant (assuming release from the gap is a first order rate process), and a diffusivity constant (assuming transport in the gap is dominated by a diffusional process). Measured release data from possessing various states of defection are use in this analysis. One element (irradiated in an earlier experiment by MacDonald) was defected with a small drilled hole. A second element was machined with 23 slits while a third element (fabricated with a porous end plug) displayed through-wall sheath hydriding. Comparison of measured release data with calculated values from the model yields estimates of empirical diffusion coefficients for the radioactive species in the UO 2 (1.56 x 10 -10 to 7.30 x 10 -9 s -1 ), as well as escape rate constants (7.85 x 10 -7 to 3.44 x 10 -5 s -1 ) and diffusion coefficients (3.39 x 10 -5 to 4.88 x 10 -2 cm 2 /s) for these in the fuel-to-sheath gap. Analyses also enable identification of the various rate-controlling processes operative in each element. For the noble gas and iodine species, the rate-determining process in the multi-slit element is 'Booth diffusion'; however, for the hydrided element an additional delay results from diffusional transport in the fuel-to-heath gap. Furthermore, the iodine species exhibit an additional holdup in the drilled element because of significant trapping on the fuel and/or sheath surfaces. Using experimental release data and applying the theoretical results of this work, a systematic procedure is proposed to characterize fuel failures in commercial power reactors (i.e., the number of fuel failures and average leak size)

Performance of MOX fuel: An overview of the experimental programme of the OECD Halden Reactor Project and review of selected results

International Nuclear Information System (INIS)

Wiesenack, W.; McGrath, M.

2000-01-01

The OECD Halden Reactor Project has defined an extensive experimental programme related to MOX fuels which is being executed with the objective to provide a performance data base similar to that available for UO 2 . In addition to utilising fresh MOX fuel and re-instrumented segments from LWR irradiations to high burnup, the concept of inert matrix fuel is being addressed. The irradiation in the Halden reactor is performed in rigs allowing steady state, power ramping and cyclic operation. In-pile data are obtained from instrumentation such as fuel centreline thermocouples, pressure transducers, fuel and cladding elongation detectors, and movable gauges for measuring the diametral deformation. Various phenomena can be assessed in this way, e.g. thermal performance, swelling and densification, PCMI and fission gas release. The paper describes the objectives of various experiments and provides examples of temperature, pressure and cladding elongation measurements performed on MOX fuel. Salient results are related to the threshold for the onset of significant fission gas release and the relaxation behaviour in a power ramp-PCMI situation. (author)

G 2 reactor project; Projet de pile a double fin: G 2

Energy Technology Data Exchange (ETDEWEB)

Ailleret, [Electricite de France (EDF), Dir. General des Etudes de Recherches, 75 - Paris (France); Taranger, P; Yvon, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

The CEA actually constructs the G-2 reactor core working with natural uranium, which will use graphite as moderator, and gas under pressure as cooling fluid. This report presents the specificity of the new reactor: - the different elements of the reactor core, - the control and the security of the reactor, - the renewal of the fuel, - the biologic surrounding wall, - and the cooling circuit. (M.B.) [French] le Commissariat a l'Energie Atomique construit actuellement la pile G-2 a Uranium naturel, qui utilisera le graphite comme moderateur, et le gaz sous pression comme fluide de refroidissement. Ce rapport presente les specificite du nouveau reacteur: - les differents elements de la pile, - le controle et la securite du reacteur, - le renouvellement du combustible, - l'enceinte biologique, - et le circuit de refroidissement. (M.B.)

Safety against releases in severe accidents. Annual report 1996. Project plan 1997

International Nuclear Information System (INIS)

1997-01-01

The work scope of the RAK-2 project is divided into three sub-projects: RAK-2.1 Severe Accident Phenomenology; RAK-2.2 Computerised Accident Management; RAK-2.3 Reactors In Nordic Surroundings. The work in subproject 1 progresses roughly according to budget and time schedule. Some adjustments in the technical work scope were made during 1996. Main tasks of RAK-2.1 in 1996: Complete recriticality studies for Nordic BWRs; Investigate phenomena related to late phase melt progression; Issue and NKS Final Technical Report on KTH experiments. Main tasks of RAK-2.2 in 1996: CAMS would be further developed with signal validation, tracking simulation, state identification and PSA and risk monitoring applications; Carry out a feasibility study for development of a PWR version of CAMS in collaboration with EdF, France; Use CAMS in the Halden Man-Machine laboratory to perform human factor studies. Main tasks of RAK-2.3 in 1996: Collect and report data from the British reactor types AGR, MAGNOX and PWR; Make a report on accidents in nuclear ships; Put the collected data together in a common data base covering neighbour reactors treated in SIK-3 and RAK-2.3; Update the data in the former SIK-3 report if needed. The work in project 2 progresses according to plans. The data collection of British reactors with in sub-project 3 has been delayed significantly due to difficulty of obtaining information from some of the British utilities, but the problems are expected to be solved by the end of 1997. (EG)

Umatilla Satellite and Release Sites Project : Final Siting Report.

Energy Technology Data Exchange (ETDEWEB)

Montgomery, James M.

1992-04-01

This report presents the results of site analysis for the Umatilla Satellite and Release Sites Project. The purpose of this project is to provide engineering services for the siting and conceptual design of satellite and release facilities for the Umatilla Basin hatchery program. The Umatilla Basin hatchery program consists of artificial production facilities for salmon and steelhead to enhance production in the Umatilla River as defined in the Umatilla master plan approved in 1989 by the Northwest Power Planning Council. Facilities identified in the master plan include adult salmon broodstock holding and spawning facilities, facilities for recovery, acclimation, and/or extended rearing of salmon juveniles, and development of river sites for release of hatchery salmon and steelhead. The historic and current distribution of fall chinook, summer chinook, and coho salmon and steelhead trout was summarized for the Umatilla River basin. Current and future production and release objectives were reviewed. Twenty seven sites were evaluated for the potential and development of facilities. Engineering and environmental attributes of the sites were evaluated and compared to facility requirements for water and space. Site screening was conducted to identify the sites with the most potential for facility development. Alternative sites were selected for conceptual design of each facility type. A proposed program for adult holding facilities, final rearing/acclimation, and direct release facilities was developed.

Kazakhstan participation in International Experimental Reactor ITER Construction project. Work status and prospects

International Nuclear Information System (INIS)

Tazhibayeva, I.L.; Tukhvatullin, Sh.T.; Shestakov, V.P.; Kuznetsov, B.A.

2002-01-01

Kazakhstan takes part in ITER project in partnership with Russian Federation since the year of 1994. At present the technical stage of the project is completed and ITER Council should take a decision on the site for international reactor. Four countries such as Canada, Japan, Spain and France have offered their territories for being used as site for launching ITER construction. ITER partners started preparing new international agreement that will cover activities on construction, operation and decommissioning of ITER. It will also include the list of research and experimental work that is conducted in support of ITER project. Kazakhstan has already made an important contribution into technical stage realization of ITER project due to scientific and technical researches conducted by National Nuclear Center, by Institute of Experimental and Theoretical Physics and by JSC 'Ulba Metallurgical plant' ('UMP'). Research activity carried out for the support of ITER project is performed in accordance with the following main trends: Tritium safety (permeability and retentin of hydrogen isotopes during in-pile irradiation in various structural materials, co-deposed layers and protective coatings); Verification of computer codes (LOCA type) loss of coolant accidents modeling in ITER reactor; Investigation of liquid metal blanket of thermonuclear reactor (tritium production in lithium containing eutectics Li17Pb83 and ceramics Li 2 TiO 3 , study of tritium permeability). At present the working group of ITER project participants started introducing proposals for cost distribution and for placing the orders on reactor construction. Further Kazakhstan participation in ITER project may be in manufacturing high-tech parts and assemblies from commercial grades of beryllium. They will be used for armouring the reactor first wall, for its thermal protection and for protection of superconductor's components for magnetic systems that are at JSC U MP'. Scientific and technical support of

Simulation of pulsed accidental energy release in a reactor core

International Nuclear Information System (INIS)

Ryshanskii, V.A.; Ivanov, A.G.; Uskov, A.A.

1995-01-01

At the present time the strength of the load-bearing members of VVER and fast reactors during a hypothetical accident is ordinarily investigated in model experiments [1]. A power burst during an accident is simulated by a nonnuclear exothermal reaction in water, which simulates the coolant and fills the model. The problem is to make the correct choice of the simulator of the accidental energy burst as an effective (i.e., sufficiently high working capacity) source of dangerous loads, corresponding to the conditions of an accident. What factors and parameters determine the energy release? The answers to these questions are contradictory

Influence of corium oxidation on fission product release from molten pool

International Nuclear Information System (INIS)

Bechta, S.V.; Krushinov, E.V.; Vitol, S.A.

2009-01-01

Release of low-volatile fission products and core materials from molten oxidic corium was investigated in the EVAN project under the auspices of ISTC. The experiments carried out in cold crucible with induction heating and RASPLAV test facility are described. The results are discussed in terms of reactor application; in particular, pool configuration, melt oxidation kinetics, critical influence of melt surface temperature and oxidation index on the fission product release rate and aerosol particle composition. The relevance of measured high release of Sr from the molten pool for the reactor application is highlighted. Comparisons of the experimental data with those from the COLIMA CA-U3 test and the VERCORS tests, as well as with predictions from IVTANTHERMO and GEMINI/NUCLEA are set. (author)

Decontamination and decommissioning of the Experimental Boiling Water Reactor (EBWR): Project final report, Argonne National Laboratory

International Nuclear Information System (INIS)

Fellhauer, C.R.; Boing, L.E.; Aldana, J.

1997-03-01

The Final Report for the Decontamination and Decommissioning (D ampersand D) of the Argonne National Laboratory - East (ANL-E) Experimental Boiling Water Reactor (EBWR) facility contains the descriptions and evaluations of the activities and the results of the EBWR D ampersand D project. It provides the following information: (1) An overall description of the ANL-E site and EBWR facility. (2) The history of the EBWR facility. (3) A description of the D ampersand D activities conducted during the EBWR project. (4) A summary of the final status of the facility, including the final and confirmation surveys. (5) A summary of the final cost, schedule, and personnel exposure associated with the project, including a summary of the total waste generated. This project report covers the entire EBWR D ampersand D project, from the initiation of Phase I activities to final project closeout. After the confirmation survey, the EBWR facility was released as a open-quotes Radiologically Controlled Area,close quotes noting residual elevated activity remains in inaccessible areas. However, exposure levels in accessible areas are at background levels. Personnel working in accessible areas do not need Radiation Work Permits, radiation monitors, or other radiological controls. Planned use for the containment structure is as an interim transuranic waste storage facility (after conversion)

Furfural production from biomass pretreatment hydrolysate using vapor-releasing reactor system.

Science.gov (United States)

Liu, Lu; Chang, Hou-Min; Jameel, Hasan; Park, Sunkyu

2018-03-01

Biomass hydrolysate from autohydrolysis pretreatment was used for furfural production considering it is in rich of xylose, xylo-oligomers, and other decomposition products from hemicellulose structure. By using the vapor-releasing reactor system, furfural was protected from degradation by separating it from the reaction media. The maximum furfural yield of 73% was achieved at 200 °C for biomass hydrolysate without the use of the catalyst. This is because the presence of organic acids such as acetic acid in hydrolysate functioned as a catalyst. According to the results in this study, biomass hydrolysate with a vapor-releasing system proves to be efficient for furfural production. The biorefinery process which allows the separation of xylose-rich autohydrolysate from other parts from biomass feedstock also improves the overall application of the biomass. Copyright © 2018 Elsevier Ltd. All rights reserved.

Atmospheric dilution factors for radioactive releases from Inshas research reactor, Egypt

International Nuclear Information System (INIS)

Abdel Aal, M.M.; Aly, A.I.M.; Tawfik, F.S.

1994-01-01

In the frame of assessing the suitability of Inshas site for constructing a new research reactor 20 MW, the meteorological condition are analyzed to determine the most affected population sectors. The atmospheric stability classes are estimated by a developed computer program in which the meteorological data for one year are used as input data. The results indicate that stability class F (moderately stable) is predominant one. The dilution factor is calculated using the computer code XOQDOQ for meteorological evaluation of routine effluent releases at nuclear power stations, which implements regulatory Guide 1.111 for both normal and desert conditions and for ground and elevated releases. The concentration isopleths are plotted and the most affected sector is the southern one with higher values for desert condition than the corresponding normal condition at same distance from the source. 4 fig., 3 tab

Comparison of some gamma detectors and environmental measurement of small Ar41 releases from a Triga reactor

International Nuclear Information System (INIS)

Baers, B.; Kautto, A.M.T.

1977-11-01

GM-detectors, liquid- and NaI(Tl)-scintillation detectors and semiconductor detectors were compared in order to measure small airborne Ar 41 activity concentrations. A 12,5 cm x 12,5 cm NaI(Tl)-scintillation detector was used to semiempirically estimate the radiation exposure arising from airborne Ar 41 release passing 5 meters (estimated) above the detector at a distance of 130 meters from a 250 kW Triga-reactor under downwind conditions. The height of the release point was 19 m. The exposure was found to be 0.45 μR/h at an Ar 41 release rate of 18 mCi/h (670 MBq/h) under downwind conditions and at a wind speed of 3 m/s. The mean annual exposure from 1300 hours reactor operation is of the order of 40...100 μR/y (+100%,-50%) at this test point and at a release rate of 2.5...6μCi/s. The maximum exposure at the ground level is at a distance of about 200 meters (approximately 10 x height of chimney) and it is of the order of 100 μR/y. At close distances from the point of release a line source model can be used for the approximate estimation of the exposure. (author)

Tripeptide amide L-pyroglutamyl-histidyl-L-prolineamide (L-PHP-thyrotropin-releasing hormone, TRH) promotes insulin-producing cell proliferation.

Science.gov (United States)

Luo, LuGuang; Luo, John Z Q; Jackson, Ivor

2013-02-01

A very small tripeptide amide L-pyroglutamyl-L-histidyl-L-prolineamide (L-PHP, Thyrotropin-Releasing Hormone, TRH), was first identified in the brain hypothalamus area. Further studies found that L-PHP was expressed in pancreas. The biological role of pancreatic L-PHP is still not clear. Growing evidence indicates that L-PHP expression in the pancreas may play a pivotal role for pancreatic development in the early prenatal period. However, the role of L-PHP in adult pancreas still needs to be explored. L-PHP activation of pancreatic β cell Ca2+ flow and stimulation of β-cell insulin synthesis and release suggest that L-PHP involved in glucose metabolism may directly act on the β cell separate from any effects via the central nervous system (CNS). Knockout L-PHP animal models have shown that loss of L-PHP expression causes hyperglycemia, which cannot be reversed by administration of thyroid hormone, suggesting that the absence of L-PHP itself is the cause. L-PHP receptor type-1 has been identified in pancreas which provides a possibility for L-PHP autocrine and paracrine regulation in pancreatic function. During pancreatic damage in adult pancreas, L-PHP may protect beta cell from apoptosis and initiate its regeneration through signal pathways of growth hormone in β cells. L-PHP has recently been discovered to affect a broad array of gene expression in the pancreas including growth factor genes. Signal pathways linked between L-PHP and EGF receptor phosphorylation suggest that L-PHP may be an important factor for adult β-cell regeneration, which could involve adult stem cell differentiation. These effects suggest that L-PHP may benefit pancreatic β cells and diabetic therapy in clinic.

Management of the decommissioning of the Thetis reactor

Energy Technology Data Exchange (ETDEWEB)

Ooms, Luc; Maris, Patrick; Noynaert, Luc [SCK-CEN, Mol (Belgium)

2013-07-01

decommissioning job. We gained the decommissioning license in May 2012. We also prepared the software tool allowing managing the decommissioning project by updating the inventory and recording the progress, the characterization measurements and the material and waste production. This software allows also to trace all the material streams and to report to the Authorities. This software is a simplified release of the ones developed by SCK-CEN in the framework of other decommissioning projects like BR3 and Belgonucleaire. The dismantling of the reactor i.e. reactor pool, circuits and rabbit system, will be performed in 2013. In 2014, it is planned to map all the surfaces of the infrastructure to highlight residual contamination of floor, walls and ceiling. The contaminated surfaces will be decontaminated and controlled. The objective is to reach the free release of the reactor building and laboratories by the end of 2014. (authors)

MARSAME Radiological Release Report for Archaeological Artifacts Excavated from Area L

Energy Technology Data Exchange (ETDEWEB)

Ruedig, Elizabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Whicker, Jeffrey Jay [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Gillis, Jessica Mcdonnel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-06-03

In 1991 Los Alamos National Laboratory’s (LANL’s) cultural resources team excavated archaeological site LA 4618 located at Technical Area 54, within Material Disposal Area L (MDA L). MDA L received non-radioactive chemical waste from the early 1960s until 1985. Further development of the MDA required excavation of several cultural sites under National Historic Preservation Act requirements; artifacts from these sites have been subsequently stored at LANL. The LANL cultural resources group would now like to release these artifacts to the Museum of Indian Arts and Culture in Santa Fe for curation. The history of disposal at Area L suggests that the artifact pool is unlikely to be chemically contaminated and LANL staff washed each artifact at least once following excavation. Thus, it is unlikely that the artifacts present a chemical hazard. LANL’s Environmental Stewardship group (EPC-ES) has evaluated the radiological survey results for the Area L artifact pool and found that the items described in this report meet the criteria for unrestricted radiological release under Department of Energy (DOE) Order 458.1 Radiation Protection of the Public and the Environment and are candidates for release without restriction from LANL control. This conclusion is based on the known history of MDA L and on radiation survey data.

The neutron utilization and promotion program of TRR-II research reactor project in Taiwan

International Nuclear Information System (INIS)

Gone, J.K.; Huang, Y.H.

2001-01-01

The objective of the Taiwan research reactor system improvement and utilization promotion project is to reconstruct the old Taiwan research reactor (TRR), which was operated by the Institute of Nuclear Energy Research (INER) between 1973 and 1988, into a multi-purpose medium flux research reactor (TRR-II). The project started in 1998, and the new reactor is scheduled to have its first critical in June of 2006. The estimated maximum unperturbed thermal neutron flux (E 14 n/cm 2 sec, and it is about one order of magnitude higher than other operating research reactors in Taiwan. The new reactor will equip with secondary neutron sources to provide neutrons with different energies, which will be an essential tool for advanced material researches in Taiwan. One of the major tasks of TRR-II project is to promote domestic utilization of neutrons generated at TRR-II. The traditional uses of neutrons in fuel/material research, trace element analysis, and isotope production has been carried out at INER for many years. On the other hand, it is obvious that promotions of neutron spectrometric technique will be a major challenge for the project team. The limited neutron flux from operating research reactors had discouraged domestic users in developing neutron spectrometric technique for many years, and only few researchers in Taiwan are experienced in using spectrometers. It is important for the project team to encourage domestic researchers to use neutron spectrometers provided by TRR-II as a tool for their future researches in various fields. This paper describes the current status of TRR-II neutron utilization and promotion program. The current status and future plans for important issues such as staff recruiting, personnel training, international collaboration, and promotion strategy will be described. (orig.)

Super safe small reactor RAPID-L conceptual design and R and D. JAERI's nuclear research promotion program, H11-002 (Contract research)

International Nuclear Information System (INIS)

Kambe, Mitsuru; Tsunoda, Hirokazu; Mishima, Kaichiro; Kawasaki, Akira; Iwamura, Takamichi

2003-03-01

The 200 kWe uranium nitride fueled lithium cooled fast reactor 'RAPID-L' combined with thermoelectric power conversion system that can be operated unmanned without refueling for up to ten years has been demonstrated. The RAPID refueling concept enables quick and simplified refueling, and achieves plant design lifetime over 20 years. A significant advantage of the RAPID-L design, which does not require the use of control rods - is the introduction of the innovative reactivity control systems: lithium expansion module (LEM), lithium injection module (LIM) and lithium release module (LRM). LEM is the most promising candidate for improving inherent reactivity feedback. LEMs could realize burnup compensation. LIMs assure sufficient negative reactivity feedback in unprotected transients. LRMs enable an automated reactor startup by detecting the hot standby temperature of the primary coolant. All these systems use 6 Li as liquid poison and are actuated by highly reliable physical properties (volume expansion of 6 Li for LEM, and freeze seal melting for LIM and LRM). (author)

Review of uncertainty estimates associated with models for assessing the impact of breeder reactor radioactivity releases

International Nuclear Information System (INIS)

Miller, C.; Little, C.A.

1982-08-01

The purpose is to summarize estimates based on currently available data of the uncertainty associated with radiological assessment models. The models being examined herein are those recommended previously for use in breeder reactor assessments. Uncertainty estimates are presented for models of atmospheric and hydrologic transport, terrestrial and aquatic food-chain bioaccumulation, and internal and external dosimetry. Both long-term and short-term release conditions are discussed. The uncertainty estimates presented in this report indicate that, for many sites, generic models and representative parameter values may be used to calculate doses from annual average radionuclide releases when these calculated doses are on the order of one-tenth or less of a relevant dose limit. For short-term, accidental releases, especially those from breeder reactors located in sites dominated by complex terrain and/or coastal meteorology, the uncertainty in the dose calculations may be much larger than an order of magnitude. As a result, it may be necessary to incorporate site-specific information into the dose calculation under these circumstances to reduce this uncertainty. However, even using site-specific information, natural variability and the uncertainties in the dose conversion factor will likely result in an overall uncertainty of greater than an order of magnitude for predictions of dose or concentration in environmental media following shortterm releases

Project margins of advanced reactor design WWER-500

International Nuclear Information System (INIS)

Rogov, M.F.; Birukov, G.I.; Ershov, V.G.; Volkov, B.E.

1994-01-01

Project criteria for design of advanced WWER-500 reactor within design conditions are compared to the requirements of the Russian regulatory guides. Normal operation limits, safe operation limits for main anticipated operational occurrences and design limits accepted for design basis accidents are considered as in preliminary safety report. It is shown that the basic design criteria in the design of WWER-500 for the anticipated operational occurrences and for design basis accidents are more severe than required in the following regulatory guides General Safety Regulations for Nuclear Power Plants and Nuclear Safety Rules for Reactors of Nuclear Power Plants. This provides certain margins from safety point of view

Water vapor as a perspective coolant for fast reactors

International Nuclear Information System (INIS)

Kalafati, D.D.; Petrov, S.I.

1978-01-01

Based on analysis of foreign projects of nuclear power plants with steam-cooled fast reactors, it is shown that low breeding ratio and large doubling time were caused by using nickel alloys, high vapor pressure and small volume heat release. The possibility is shown of obtaining doubling time in the necessary limits of T 2 =10-12 years when the above reasons for steam-cooled reactors are eliminated. Favourable combination of thermophysical and thermodynamic properties of water vapor makes it perspective coolant for power fast reactors

Measurement of Ar41 release from a TRIGA reactor

International Nuclear Information System (INIS)

Baers, B.; Kautto, A.M.T.

1978-01-01

The properties of four types of gamma sensitive (Ar-41 1.29 MeV) detectors were investigated: 10 GM tubes, 1 liquid scintillation detector, NaI(Tl)-detector and Ge(Li)-detector. The ratio of the integrated net counts per statistical uncertainty was used as a figure of merit. A uniform Ar-41 activity concentration of 14.8 Bq/m 3 was simulated with a Co-60 point source of 9.6 MBq and a measuring time of 10 min. Due to temperature instabilities the normal release was not clearly detected. Therefore the detector response was obtained for pulse releases. By weighting the experimental exposure estimate with the yearly wind distributions (velocity and direction), the yearly exposure arising from 1300 hours operation of the 250 kW TRIGA reactor was estimated to 40...100 μR/y (+100% -50%) at the test point (at the height of 13 meters) for an Ar-41 release of 440...1000 GBq/y (12...28 Ci/y). By applying a line source approximation the exposure at the ground level and close distances was estimated. The maximum average exposure at a distance of about 200 meters (10 times the height of the chimney) was estimated to be about 100 μR/y. (10 times the height of the chimney) was estimated to be about 100 yR/y. Thus the radiation dose to the public is much lower than generally applied limits

A review of fast reactor progress in Japan

Energy Technology Data Exchange (ETDEWEB)

Tomabechi, K [Power Reactor and Nuclear Fuel Development Corporation, Tokyo (Japan)

1978-07-01

The fast reactor development project in Japan is continuing at a slightly increased scale of effort in budget. The total budget for LMFBR development for fiscal year 1978 was 24 billion yen. In August 1977 major industries engaged in LMFBR have set up an office where design work can be jointly conducted. Highlights and topics of the fast reactor development activities cover description of JOYO reactor, its first criticality experiment, and the prototype fast breeder MONJU. Research and development programmes dealt with fission products release and its possible interaction with the soodium coolant, inspection of reactor components, experiments simulating sodium leakage, development of steam generator.

Lessons learned in process control at the Halden Reactor Project

International Nuclear Information System (INIS)

Kennedy, W.G.

1989-12-01

This report provides a list of those findings particularly relevant to regulatory authorities that can be derived from the research and development activities in computerized process control conducted at the Halden Reactor Project. The report was prepared by a staff member of the US Nuclear Regulatory Commission working at Halden. It identifies those results that may be of use to regulatory organizations in three main areas: as support for new requirements, as part of regulatory evaluations of the acceptability of new methods and techniques, and in exploratory research and development of new approaches to improve operator performance. More than 200 findings arranged in nine major categories are presented. The findings were culled from Halden Reactor Project documents, which are listed in the report

RAPID-L: an operator-free reactor for the Moon

International Nuclear Information System (INIS)

Kambe, M.; Tsunoda, Kh.; Misima, K.; Ivamura, T.

2005-01-01

An outlook of using the RAPID-L nuclear energy facility with a fast reactor under conditions of self-contained operation on the Moon is considered in the context of approval of the new space development program in the USA [ru

Using the model release ARTM associated with resources for simulation geoprocessing radiological environmental impact of atmospheric emissions from a research reactor

International Nuclear Information System (INIS)

Alves, Simone Fonseca

2013-01-01

The knowledge of the dispersion of radionuclides emissions into the atmosphere arising from a nuclear reactor, in normal operation, is an important step in the process of the nuclear and environmental assessment study. These processes require an assessment study of the radiological environmental impact. However, to estimate this impact a simulation of the transport mechanisms and deposition of pollutants released into the atmosphere is required. The present study aimed at the application of the dispersion model ARTM (Atmospheric Radionuclide Transport Model), together with the powerful tools of the GIS (Geographic Information System) for the environmental impact assessment of a radiological nuclear reactor under typically routine and conditions. Therefore some important information from the national project for a research reactor known as Brazilian Multipurpose Reactor (RMB) was considered. The information of the atmospheric emissions of the reactor, needed for the simulation of this project, was based on data of the Open Pool Australian Light Water (OPAL).Other important data that had to be collected and analyzed were the source term, the topography, the meteorology and the environmental data. The radionuclides analyzed as pollutants were 41 Ar; 140 Ba; 51 Cr; 137 Cs; 131 I; 133 I; 85m Kr; 87 Kr; 88 Kr; 140 La; 133 Xe; 135 Xe; 3 H; 90 Sr. The model was run for two chronological scenarios according to their meteorological data for the years 2009 and 2010, respectively. The adoption of GIS techniques was relevant in planning, data preprocessing and in the post-processing of results as well. After pre-processing, the input data were processed by the ARTM dispersion model. Maps, charts, and tables were then produced and evaluated. According to the simulated and evaluated scenarios it could be concluded that exposure pathways that mostly contributed to the dose for individual public were 41 Ar, for immersion in the plume, and 133 I, for inhalation. Nevertheless, even

Estimation of large early release frequency for Advanced Heavy Water Reactor

International Nuclear Information System (INIS)

Santhosh, T.V.; Thangamani, I.; Shrivastava, A.; Vinod, Gopika; Verma, Vishnu; Vijayan, P.K.

2015-01-01

Level 2 probabilistic safety assessment (PSA) examines severe accidents through a combination of probabilistic and deterministic approaches, in order to determine the release of radionuclides from containment, including the physical processes that are involved in the loss of structural integrity of the reactor core. The probabilistic part focuses on the reliability evaluation of containment systems and the deterministic part focuses on the analysis of the physical processes of an accident (timing and magnitude of radioactivity release), and the response of the containment. The important tasks involved are: (i) grouping and categorization of accident sequences into plant damage states (PDSs) (ii) development of a containment event trees (CETs) (iii) development of CET top event definitions and quantification of failure probabilities, and (iv) assigning the release categories and estimation of large early release frequency (LERF). LERF is defined as the frequency of those accidents leading to rapid, unmitigated release of airborne fission products from the containment to the environment occurring before the effective implementation of offsite emergency response and protective actions such that there is the potential for early health effects. Such accidents generally include unscrubbed releases associated with early containment failure shortly after vessel breach, containment bypass events, and loss of containment isolation. Preliminary assessment of LERF, based on release categorization from qualitative expert judgement, has been carried out and the estimated LERF is found to be 1e-13/yr. The dominant contributors are: (a) LB LOCA with the failure of prompt shutdown coupled with containment isolation failure, (b) containment bypass event from main steam line break outside containment coupled with failure of main steam isolation valves, and (c) LB LOCA with complete failure of emergency core cooling system (ECCS) and loss of moderator cooling

Balance and behavior of gaseous radionuclides released during initial fast reactor fuel reprocessing operations

International Nuclear Information System (INIS)

Leudet, A.; Goumondy, J.P.; Charrier, G.

1985-10-01

Five pins from the fast reactor Phenix are cut and dissolved in a specially designed cell for the accurate determination of gas released during the operation. Amount and activity of gaseous radionuclides: Kr, Xe, Kr-85, I, I-129, H-3 and C-14 are determined in the fuel pins and also their distribution between shearing and dissolution [fr

Job task and functional analysis of the Division of Reactor Projects, office of Nuclear Reactor Regulation. Final report

Energy Technology Data Exchange (ETDEWEB)

Morzinski, J.A.; Gilmore, W.; Hahn, H.A.

1998-07-10

A job task and functional analysis was recently completed for the positions that make up the regional Divisions of Reactor Projects. Among the conclusions of that analysis was a recommendation to clarify roles and responsibilities among site, regional, and headquarters personnel. As that analysis did not cover headquarters personnel, a similar analysis was undertaken of three headquarters positions within the Division of Reactor Projects: Licensing Assistants, Project Managers, and Project Directors. The goals of this analysis were to systematically evaluate the tasks performed by these headquarters personnel to determine job training requirements, to account for variations due to division/regional assignment or differences in several experience categories, and to determine how, and by which positions, certain functions are best performed. The results of this analysis include recommendations for training and for job design. Data to support this analysis was collected by a survey instrument and through several sets of focus group meetings with representatives from each position.

Description of the blowdown test facility COG program on in-reactor fission product release, transport, and deposition under severe accident conditions

International Nuclear Information System (INIS)

Fehrenbach, P.J.; Wood, J.C.

1987-06-01

Loss-of-coolant accidents with additional impairment of emergency cooling would probably result in high fuel temperatures leading to severe fuel damage (SFD) and significant fission product activity would then be transported along the PHTS to the break where a fraction of it would be released and transport under such conditions, there are many interacting and sometimes competing phenomena to consider. Laboratory simulations are being used to provide data on these individual phenomena, such as UO 2 oxidation and Zr-UO 2 interaction, from which mathematical models can be constructed. These are then combined into computer codes to include the interaction effects and assess the overall releases. In addition, in-reactor tests are the only source of data on release and transport of short-lived fission product nuclides, which are important in the consequence analysis of CANDU reactor accidents. Post-test decontamination of an in-reactor test facility also provides a unique opportunity to demonstrate techniques and obtain decontamination data relevant to post-accident rehabilitation of CANDU power reactors. Specialized facilities are required for in-reactor testing because of the extensive release of radioactive fission products and the high temperatures involved (up to 2500 degrees Celsius). To meet this need for the Canadian program, the Blowdown Test Facility (BTF) has been built in the NRU reactor at Chalk River. Between completion of construction in mid-1987 and the first Zircaloy-sheathed fuel test in fiscal year 1987/88, several commissioning tests are being performed. Similarly, extensive development work has been completed to permit application of instrumentation to irradiated fuel elements, and in support of post-test fuel assembly examination. A program of decontamination studies has also been developed to generate information relevant to post-accident decontamination of power reactors. The BTF shared cost test program funded by the COG High Temperature

International Reactor Physics Experiment Evaluation (IRPhE) Project. IRPhE Handbook - 2017 edition

International Nuclear Information System (INIS)

2017-01-01

The International Reactor Physics Evaluation (IRPhE) Project was initiated as a pilot in 1999 by the Nuclear Energy Agency (NEA) Nuclear Science Committee (NSC). The project was endorsed as an official activity of the NSC in June 2003. While the NEA co-ordinates and administers the IRPhE Project at the international level, each participating country is responsible for the administration, technical direction and priorities of the project within their respective countries. The information and data included in this handbook are available to NEA member countries, to all contributing countries and to others on a case-by-case basis. The IRPhE Project is patterned after the International Criticality Safety Benchmark Evaluation Project (ICSBEP). It closely co-ordinates with the ICSBEP to avoid duplication of efforts and publication of conflicting information. Some benchmark data are applicable to both nuclear criticality safety and reactor physics technology. Some have already been evaluated and published by the ICSBEP, but have been extended to include other types of measurements in addition to the critical configuration. Through this effort, the IRPhE Project will be able to 1) consolidate and preserve the existing worldwide information base; 2) retrieve lost data; 3) identify areas where more data are needed; 4) draw upon the resources of the international reactor physics community to help fill knowledge gaps; 5) identify discrepancies between calculations and experiments due to deficiencies in reported experimental data, cross-section data, cross-section processing codes and neutronics codes; 6) eliminate a large amount of redundant research and processing of reactor physics experiment data, and 7) improve future experimental planning, execution and reporting. This handbook contains reactor physics benchmark specifications that have been derived from experiments performed at nuclear facilities around the world. The benchmark specifications are intended for use by

Simulation of LOFT anticipated-transient experiments L6-1, L6-2, and L6-3 using TRAC-PF1/MOD1

International Nuclear Information System (INIS)

Sahota, M.S.

1984-01-01

Anticipated-transient experiments L6-1, L6-2, and L6-3, performed at the Loss-of-fluid Test (LOFT) facility, are analyzed using the latest released version of the Transient Reactor Analysis Code (TRAC-PF1/MOD1). The results are used to assess TRAC-PF1/MOD1 trip and control capabilities, and predictions of thermal-hydraulic phenomena during slow transients. Test L6-1 simulated a loss-of-stream load in a large pressurized-water reactor (PWR), and was initiated by closing the main steam-flow control valve (MSFCV) at its maximum rate, which reduced the heat removal from the secondary-coolant system and increased the primary-coolant system pressure that initiated a reactor scram. Test L6-2 simulated a loss-of-primary coolant flow in a large PWR, and was initiated by tripping the power to the primary-coolant pumps (PCPs) allowing the pumps to coast down. The reduced primary-coolant flow caused a reactor scram. Test L6-3 simulated an excessive-load increase incident in a large PWR, and was initiated by opening the MSFCV at its maximum rate, which increased the heat removal from the secondary-coolant system and decreased the primary-coolant system pressure that initiated a reactor scram. The TRAC calculations accurately predict most test events. The test data and the calculated results for most parameters of interest also agree well

Predicted radionuclide release from reactor-related unenclosed solid objects dumped in the Sea of Japan and the Pacific Ocean, east coast of Kamchatka

International Nuclear Information System (INIS)

Mount, M.E.; Lynn, N.M.; Warden, J.M.

1996-06-01

Between 1978 and 1991 reactor-related solid radioactive waste was dumped by the former Soviet Union as unenclosed objects in the Pacific Ocean, east coast of Kamchatka, and the Sea of Japan. This paper presented estimates for the current (1994) inventory of activation and corrosion products contained in the reactor-related unenclosed solid objects. In addition, simple models derived for prediction of radionuclide release from marine reactors dumped in the Kara Sea are applied to certain of the dumped objects to provide estimates of radionuclide release to the Pacific Ocean, east coast of Kamchatka, and Sea of Japan environments. For the Pacific Ocean, east coast of Kamchatka, total release rates start below 0.01 GBq yr -1 and over 1,000 years, fall to 100 Bq yr -1 . In the Sea of Japan, the total release rate starts just above 1 GBq yr - 1 , dropping off to a level less than 0.1 GBq yr -1 , extending past the year 4,000

Results of aerosol code comparisons with releases from ACE MCCI tests

International Nuclear Information System (INIS)

Fink, J.K.; Corradini, M.; Hidaka, A.; Hontanon, E.; Mignanelli, M.A.; Schroedl, E.; Strizhov, V.

1992-01-01

Results of aerosol release calculations by six groups from six countries are compared with the releases from ACE MCCI Test L6. The codes used for these calculations included: SOLGASMIX-PV, SOLGASMIX Reactor 1986, CORCON.UW, VANESA 1.01, and CORCON mod2.04/VANESA 1.01. Calculations were performed with the standard VANESA 1.01 code and with modifications to the VANESA code such as the inclusion of various zirconium-silica chemical reactions. Comparisons of results from these calculations were made with Test L6 release fractions for U, Zr, Si, the fission-product elements Te, Ba, Sr, Ce, La, Mo and control materials Ag, In, and Ru. Reasonable agreement was obtained between calculations and Test L6 results for the volatile elements Ag, In and Te. Calculated releases of the low volatility fission products ranged from within an order of magnitude to five orders of magnitude of Test L6 values. Releases were over and underestimated by calculations. Poorest agreements were obtained for Mo and Si

An analysis of ingestion doses from a range of postulated Magnox reactor releases

International Nuclear Information System (INIS)

Nair, S.

1986-01-01

An analysis was carried out of ingestion doses from a range of postulated Magnox reactor releases to the atmosphere. Doses to the adult, ten year old child and one year old child were calculated, which showed the one year old child to receive the highest dose. Detailed studies were made of the significance of the ingestion dose to the one year old child in relation to other exposure routes. The ingestion dose was analysed for its contributing critical organs, foods and nuclides. Approximate calculations were also made of the dependence of the ingestion dose on the time of year when the release occurs. The ingestion pathway was found to dominate if the release occurs towards the end of the growing season but to be less significant relative to other exposure pathways at all other times. The calculations enabled a set of release-specific emergency action guidance levels of critical nuclide concentrations in the critical foods to be produced, which comply with NRPB's ingestion Emergency Reference Level guidelines. (author)

NORA project offers unique reactor research and advanced training opportunities

International Nuclear Information System (INIS)

1961-01-01

An international program for reactor research and advanced training for a period of three years has been established in connection with the Norwegian critical assembly NORA. The aim of the project is to determine, through integral experiments, the basic reactor physics data for lattices moderated with light-water, heavy-water or mixtures of heavy and light water, with fuels of different sizes and spacing, three different enrichments and compositions. The objectives, programme, and facilities are described in details

Estimation of release of tritium from measurements of air concentrations in reactor building of PHWR

International Nuclear Information System (INIS)

Purohit, R.G.; Sarkar, P.K.

2010-01-01

In this paper an attempt has been made to estimate the releases from measured air concentrations of tritium at various locations in Reactor Building (RB). Design data of Kaiga Generating Station and sample measurements of tritium concentrations at various locations in RB and discharges for a period of fortnight were used. A comparison has also been made with actual measurements. It has been observed that there is good matching in estimated and actual measurements of tritium release on some days while on some days there is high difference

Transport and release of fission products during nuclear reactor accident

International Nuclear Information System (INIS)

Lee, K.W.; Kuhlman, M.R.; Gieseke, J.A.

1984-01-01

This study represents the identification and formulation of a systematic, mechanistic approach to estimating source terms and the implementation of this approach through calculations of fission products release to the environment for a large PWR reactor under a selected set of accident conditions. The development and improvement of calculational procedures is an evolutionary process and in the long term must be verified through experimental studies. It is anticipated that as additional information is obtained the accuracy of predictions can be improved and uncertainties reduced. Transport and deposition of radionuclides were found to be quite dependent on the accident sequences and the corresponding thremal hydraulic conditions. Reduced temperatures led to increased deposition of vapor species, and reduced flow rates to increased aerosol deposition. It is to be recognized that the estimates of release fractions are subject to uncertainties in the data and computer models employed in the calculations and are expected to have been influenced by assumptions regarding plant geometry, thermal hydraulics, deposition mechanisms, and sequence events. The effects of these assumptions will be investigated as this study continues. (Author)

Effects of control technology on the projected krypton-85 environmental inventory

International Nuclear Information System (INIS)

Oscarson, E.E.

1973-01-01

Growth projections for the USA nuclear power industry may be used to make projections of future radioactive material inventories available for potential release to the environment. Since krypton-85 is produced in reactors, the potential routes of release to the environment are at the reactors or the fuel reprocessing plants. The present generation of reactors and fuel reprocessing plants do not use any systems to limit the release of krypton-85 into the biosphere. Clean-up systems are currently being designed and could be introduced when necessary. The cumulative inventory of krypton-85 in the environment is dependent upon the time of introduction of these clean-up systems and their efficiencies, in addition to the total quantity produced. Annual and cumulative inventories of krypton-85 are projected to increase dramatically over the next 50 years. If controls are assumed to be initiated at various years, a series of graphs of different cumulative environmental inventories and the associated doses and health effects are drawn. Varying the year of introduction and the efficiency of these systems allows one to speculate as to the optimum time for control implementation

Spanish collaboration in the OECD Halden Reactor Project research on Gadolinia Fuel

International Nuclear Information System (INIS)

Horvath, M.; Munoz-Reja, C.; Tverberg, T.; Jenssen, H. K.

2010-01-01

Safe and reliable operation of nuclear power plants benefit from research and development advances and related technical solutions. One research platform is the OECD Halden Reactor Project (HRP). HRP is a joint undertaking of national organisations in 18 countries sponsoring a jointly financed programme under the auspices of the OECD - Nuclear Energy Agency (NEA). As a member state, Spain is participating HRP research programs with ENUSA as a partner in the fuel research programs. Improving the NPP operations, fuel cycles were designed to increase fuel burnup. Higher fuel burnup reduces the number of spent fuel assemblies and thus the costs of new fuel as well as the costs of back-end management. Higher burnup is reached either by prolonging the reactor cycles or by increasing the number of reactor cycles for the fuel in the core. Both ways entail additional requirements concerning fuel enrichment and burnable absorbers as additives and adjustments on the cladding material properties, such as mechanical treatment and chemical composition of the alloys. For these demands and needs ENUSA promotes the research on high burnup effects, gadolinium doped fuels and cladding material behaviour under irradiation. Various experiments, called IFA, are developed and performed also by providing materials. ENUSA collaborates with HRP on various experiments investigating the fuel densification and swelling, fission gas release, pressure limits on UO 2 and (U,Gd)O 2 fuels (IFA-504, -515, -636, -681); the cladding creep, lift-off, corrosion and hydrides on different tubing materials (IFA-567, -610, -638); instrumentation of the experiments, especially on pre-irradiated materials (IFA-533). These experiments are combined with model calculations to improve predictions for higher burnups and to maintain safety margins (IFA-515, -636, -681). Besides these unique in-pile experiments PIEs are performed as well on fuel and structural materials to complete the scope of these studies (IFA

The preparation and the sustained release of titanium dioxide hollow particles encapsulating L-ascorbic acid

Science.gov (United States)

Tominaga, Yoko; Kadota, Kazunori; Shimosaka, Atsuko; Yoshida, Mikio; Oshima, Kotaro; Shirakawa, Yoshiyuki

2018-05-01

The preparation of the titanium dioxide hollow particles encapsulating L-ascorbic acid via sol-gel process using inkjet nozzle has been performed, and the sustained release and the effect protecting against degradation of L-ascorbic acid in the particles were investigated. The morphology of titanium dioxide particles was evaluated by scanning electron microscopy (SEM) and energy dispersive X-ray spectrometry (EDS). The sustained release and the effect protecting against degradation of L-ascorbic acid were estimated by dialysis bag method in phosphate buffer saline (PBS) (pH = 7.4) as release media. The prepared titanium dioxide particles exhibited spherical porous structures. The particle size distribution of the titanium dioxide particles was uniform. The hollow titanium dioxide particles encapsulating L-ascorbic acid showed the sustained release. It was also found that the degradation of L-ascorbic acid could be inhibited by encapsulating L-ascorbic acid in the titanium dioxide hollow particles.

Analysis and evaluation of the ASTEC model basis on fission product and aerosol release phenomena from melts. 3. Technical report

International Nuclear Information System (INIS)

Agethen, K.; Koch, M.K.

2016-04-01

The present report is the 3 rd Technical Report within the research project ''ASMO'' founded by the German Federal Ministry for Economic Affairs and Energy (BMWi 1501433) and projected at the Chair of Energy Systems and Energy Economics (LEE) within the workgroup Reactor Simulation and Safety at the Ruhr-Universitaet Bochum (RUB). The focus in this report is set on the release of fission products and the contribution to the source term, which is formed in the late phase after failure of the reactor pressure vessel during MCCI. By comparing the RUB simulation results including the fission product release rates with further simulations of GRS and VEIKI it can be indicated that the simulations have a high sensitivity in respect to the melting point temperature. It can be noted that the release rates are underestimated for most fission product species with the current model. Especially semi-volatile fission products and the lanthanum release is underestimated by several orders of magnitude. Based on the ACE experiment L2, advanced considerations are presented concerning the melt temperature, the gas temperature, the segregation and a varied melt configuration. Furthermore, the influence of the gas velocity is investigated. This variation of the gas velocity causes an underestimation of the release rates compared to the RUB base calculation. A model extension to oxidic species for lanthanum and ruthenium shows a significant improvement of the simulation results. In addition, the MEDICIS module has been enhanced to document the currently existing species, are displayed in a *.ist-file. This expansion shows inconsistencies between the melt composition and the fission product composition. Based on these results, there are still some difficulties regarding the release of fission products in the MEDICIS module and the interaction with the material data base (MOB) which needs further investigation.

LABCORE post release 1.0 development system project management plan

International Nuclear Information System (INIS)

Rich, H.S.

1994-01-01

The LABCORE post release 1.0 development system project management plan (SPMP) is the primary planning document governing the development of specific enhancements to the LABCORE project. The mission of the Westinghouse Hanford Company (WHC) laboratories is changing from supporting the 200 Area chemical processing plants for process control, waste management, and effluent monitoring to supporting environmental restoration and regulatory compliance commitments. The LABCORE program was implemented as the key element for meeting the commitments by upgrading the laboratories through the implementation of an Automated Data Processing improvement program in January 1994. Scope for LABCORE release 1.0 consisted of hardware and software implementation required to support a minimum number of analyses (Single-Shell Tank [SST] analysis at 222S Laboratory and Performance Evaluation samples at the Waste Sampling Characterization Facility laboratory) using manual entry of data, and to support routine laboratory functions, common to all laboratories. LABCORE post release 1.0 enhancements will expand the functionality presented to the laboratory. Post release 1.0 enhancements will also address the integration of a database for Analytical Services Program Integration, budgeting, and scheduling offices into LABCORE

The European Fast Breeder Reactor project (EFR). Should Germany withdraw from the project?

International Nuclear Information System (INIS)

1993-01-01

The Fed. Min. of Research and Technology has discontinued its financial aid to industry for the development of fast breeder reactor technology at the end of 1991, and a termination of the EFR project is in sight. There is, however, no need for the German government to withdraw from the EFR agreement concluded in 1984. (orig.) [de

Fission gas release from UO2 pellet fuel at high burn-up

International Nuclear Information System (INIS)

Vitanza, C.; Kolstad, E.; Graziani, U.

1979-01-01

Analysis of in-reactor measurements of fuel center temperature and rod internal pressure at the OECD Halden Reactor Project has led to the development of an empirical fission gas release model, which is described. The model originally derived from data obtained in the low and intermediate burn-up range, appears to give good predictions for rods irradiated to high exposures as well. PIE puncturing data from seven fuel rods, operated at relatively constant powers and peak center temperatures between 1900 and 2000 0 C up to approx. 40,000 MWd/t UO 2 , did not exhibit any burn-up enhancement on the fission gas release rate

International project GT-MHR - New generation of nuclear reactors

International Nuclear Information System (INIS)

Vasyaev, A.; Kodochigov, N.; Kuzavkov, N.; Kuznetsov, L.

2001-01-01

Gas turbine-modular helium reactor (GT-MHR) is the reactor of new generation, which satisfies the requirements of the progressing large-scale nuclear power engineering. The activities in GT-MHR Project started in 1995. In 1997 the Conceptual Design was developed under four-side Agreement (MINATOM, General Atomics, FRAMATOME, Fuji Electric); it has passed through the internal and international reviews, has been approved and recommended for further development as one of new trends in creation of new generation plants. Starting from 1999, the activities in the development of the Preliminary Design of the plant were deployed under the Agreement between the Government of the United States of America and the Government of the Russian Federation on Scientific and Technical Cooperation in the Management of Plutonium That Has Been Withdrawn From Nuclear Military Programs dated July 24, 1998. The activities are established under the Contract between MINATOM and OKBM Russia, and under the General Agreement between Department of Energy (DOE), USA and OKBM. The GT-MHR Project is included into 'Development Strategy of Russian Nuclear Power in the first Half of the XXI-st Century' providing for 'the participation in an international project on the development and construction of GT-MHR nuclear power plant till year 2010 and 'operation of GT-MHR prototype unit and creation of fuel fabrication facility (within framework of International Project) till year 2030'. (author)

An analysis of ingestion doses from a range of postulated Magnox reactor releases

International Nuclear Information System (INIS)

Nair, S.

1985-06-01

An analysis has been carried out of ingestion doses from a range of postulated Magnox reactor releases to atmosphere. Calculations were made of the dose to the adult, ten year old child and one year old child, which showed the one year old child to receive the highest dose. Detailed studies were made of the significance of the ingestion dose to the one year old child in relation to other exposure routes. The ingestion dose was also analysed in terms of the contributing critical organs, foods and nuclides. Approximate calculations were also made of the dependence of the ingestion dose on the time of year when the release occurs. The results of the analysis were used to derive a set of release-specific Emergency Action Guidance Levels (EAGLs) of critical nuclide concentrations in the critical foods, which comply with NRPB's ingestion ERL recommendations. The EAGLs were supplemented with a corresponding set of EAGLs for grass, for use in situations where crop samples were not readily available. (author)

Calcium modified edible Canna (Canna edulis L) starch for controlled released matrix

Science.gov (United States)

Putri, A. P.; Ridwan, M.; Darmawan, T. A.; Darusman, F.; Gadri, A.

2017-07-01

Canna edulis L starch was modified with calcium chloride in order to form controlled released matrix. Present study aim to analyze modified starch characteristic. Four different formulation of ondansetron granules was used to provide dissolution profile of controlled released, two formula consisted of 15% and 30% modified starch, one formula utilized matrix reference standards and the last granules was negative control. Methocel-hydroxypropyl methyl cellulose was used as controlled released matrix reference standards in the third formula. Calcium starch was synthesized in the presence of sodium hydroxide to form gelatinized mass and calcium chloride as the cross linking agent. Physicochemical and dissolution properties of modified starch for controlled released application were investigated. Modified starch has higher swelling index, water solubility and compressibility index. Three of four different formulation of granules provide dissolution profile of controlled released. The profiles indicate granules which employed calcium Canna edulis L starch as matrix are able to resemble controlled drug released profile of matrix reference, however their bigger detain ability lead to lower bioavailability.

Filtered atmospheric venting of light water reactor containments

International Nuclear Information System (INIS)

Hedgran, A.; Ahlstroem, P.E.; Nilsson, L.; Persson, Aa.

1982-11-01

The aim of filtered venting is to improve the function of the reactor containment in connection with very severe accidents. By equipping the containment with a safety valve for pressure relief and allowing the released gases to pass through an effective filter, it should be possible to achieve a considerable protective effect. The work has involved detailed studies of the core meltdown sequence, how the molten core material runs out of the reactor vessel, what effect it has on concrete and other structures and how final cooling of the molten core material takes place. On the basis of previous Swedish studies, the project has chosen to study a filter concept that consists of a gravel bed of large volume. This filter plant shall not only retain the radioactive particles that escape from the containment through the vent line, but shall also condense the accompanying steam. After the government decided in 1981 that Barsebaeck was to be equipped with filtered venting and issued specifications regarding its performance, the project aimed at obtaining results that could be used to design and verify a plant for filtered venting at the Barsebaeck nuclear power station. As far as the other Swedish nuclear power plants at Oskarshamn, Ringhals and Forsmark are concerned, the results are only applicable to a limited extent. Additional studies are required for these nuclear power plants before the value of filtered venting can be assessed. Based on the results of experiments and analyses, the project has made a safety analysis with Barsebaeck as a reference plant in order to study how the introduction of filtered venting affects the safety level at a station. In summary, the venting function appears to entail a not insignificant reduction of risks for boiling water reactors of the Barsebaeck type. For a number of types of such very severe core accident cases, the filter design studied ensures a substantial reduction of the releases. However it has not been possible within the

A long term radiological risk model for plutonium-fueled and fission reactor space nuclear system

International Nuclear Information System (INIS)

Bartram, B.W.; Dougherty, D.K.

1987-01-01

This report describes the optimization of the RISK III mathematical model, which provides risk assessment for the use of a plutonium-fueled, fission reactor in space systems. The report discusses possible scenarios leading to radiation releases on the ground; distinctions are made for an intact reactor and a dispersed reactor. Also included are projected dose equivalents for various accident situations. 54 refs., 31 figs., 11 tabs

Status report on the Experimental Boiling Water Reactor (EBWR) Decontamination and Decommissioning (D ampersand D) Project

International Nuclear Information System (INIS)

Sears, L.; Garlock, G.; Mencarelli, R.; Fellhauer, C.

1994-01-01

ALARON Corporation is under contract, to Argonne National Laboratory - East (ANL-E), to complete the decontamination and decommissioning of the Experimental Boiling Water Reactor (EBWR). The project, begun, in 1986 by ANL-E personnel, is projected to be completed by the end of 1994. The final phase of work was awarded to ALARON in December 1993 with the scope of work including the disassembly and removal of all remaining reactor internals, the reactor vessel, the lead bio-shield, the core liner, and the activated portion of the concrete bio-shield. This paper discusses the work undertaken beginning in January 1994 and continuing through July 1994. During this period the required pre-mobilization documentation was prepared and approved, mobilization was completed, and the reactor internals, reactor vessel, lead bio-shield and core liner were removed. The paper will compare the planned schedule to the actual schedule, discuss problems encountered, review volume reduction techniques and health and safety issues including radiological aspects of the project

Progress and status of the international project on innovative nuclear reactors and fuel cycles (INPRO) - 5182

International Nuclear Information System (INIS)

Ponomarev, A.; Fesenko, G.; Grigoriev, F.G.; Korinny, A.; Phillips, J.R.; Rho, K.

2015-01-01

The IAEA's International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO) was established in 2000 through IAEA General Conference resolution. INPRO cooperates with Member States to ensure that sustainable nuclear energy is available to help meet the energy needs of the 21. century. INPRO membership has grown to 41 members and 16 observers. The paper presents the current prospectus of the INPRO programme and details the most recent achievements in the following 7 projects: 1) the GAINS project (Global Architecture of Innovative Nuclear Energy Systems with thermal and fast reactors and a closed nuclear fuel cycle); 2) the SYNERGIES project applies and amends the analytical framework developed in GAINS project to examine more specifically the various forms of regional collaboration among nuclear energy suppliers and users; 3) the KIND project (Key Indicators for Innovative Nuclear Energy Systems) has the objective of developing guidance on the evaluation on innovative nuclear technologies; 4) the ROADMAPS project addresses several possible stages toward nuclear energy sustainability; 5) the RISC project aims at demonstrating that the evolution of safety requirements and technical innovations provide continual progress towards the avoidance of evacuation measures outside NPP sites in case of severe accidents; 6) the FANES project has the objective of carrying out feasibility analyses of advanced and innovative fuels for different reactor systems; and 7) the WIRAF project aims at identifying problematic waste from innovative reactor designs and corresponding nuclear fuel cycles

The action of the project coordinator with respect to reactor safety

International Nuclear Information System (INIS)

Leclercq, Jacques

1981-01-01

Before describing the various actions of the project coordinator (EDF) entrusted with the building of nuclear power stations, with respect to reactor safety in France, the definition of reactor safety and the various participants are mentioned first. These participants are: the Government Departments and the Experts involved (the Department of Nuclear Safety of the 'Institut de Protection et de Surete Nucleaire' forming the first technical support) and the applicant, namely the EDF. The reactor safety actions of the project coordinator are defined as from the following components: 1 - The targets laid down with respect to safety, the final objective being the protection of workers and the public against the potential dangers of the installations, principally against radiation. 2 - The safety methodology at the design stage of the power station: 'barrier' method, defence method in depth at three levels, lines of assurance method, and probabilistic method. 3 - Safety actions at the construction stage within the context of an assurance of quality programe. 4 - Safety at the trials, commissioning and operating stage, with the backing of the 'Groupe Operationnel de Demarrage (G.O.D.)' and the 'Commission d'Essais sur Site (C.E.S.)'. An initial balance sheet of the reactor safety actions for the PWR units built by the EDF is presented [fr

On Brazil's participation in the International Project on Innovative Nuclear Reactors and Fuels Cycles (INPRO)

International Nuclear Information System (INIS)

Goncalves Filho, Orlando Joao Agostinho

2007-01-01

In response to a resolution of its 44th General Conference (GC(44)/RES/21) held in September 2000, the International Atomic Energy Agency launched in May 2001 the International Project on Innovative Nuclear Reactors and Fuels Cycles (INPRO) with the objective of supporting the safe, sustainable, economic and proliferation-resistant use of nuclear technology to meet the global energy needs of the 21st century. Brazil joined the project from its beginnings and in 2005 submitted a proposal for the screening assessment using INPRO methodology of two small-size light-water reactors as potential components of an innovative nuclear reactor system (INS) completed with a conventional open nuclear fuel cycle. The INS reactor components currently being assessed are the International Reactor Innovative and Secure (IRIS) that is being developed by an international consortium made of 21 organizations from 10 countries (Brazil included) led by the Westinghouse Company, and the Fixed Bed Nuclear Reactor (FBNR) that is being developed at the Federal University of Rio Grande do Sul. This paper gives an overview of Brazil's participation in INPRO, highlighting the objective, scope and intermediate results of the assessment study being performed, and the possibilities for participation in one or two collaborative research projects under INPRO Phase 2 Action Plan for 2008-2009. (author)

Recuperation of the energy released in the G-1, an air-cooled graphite reactor core; Recuperation de l'energie degagee dans G 1 pile a graphite refroidie a l'air

Energy Technology Data Exchange (ETDEWEB)

Chambadal, P [Electricite de France (EDF), 75 - Paris (France); Pascal, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

The CEA (in his five-year setting plan) has objective among others, the realization of the two first french reactors moderated with graphite. The construction of the G-1 reactor in Marcoule, first french plutonic core, is achieved so that it will diverge in the beginning of 1956 and reach its full power in the beginning of the second semester of the same year. In this report we will detail the specificities of the reactor and in particular its cooling and energy recuperation system. The G-1 reactor being essentially intended to allow the french technicians to study the behavior of an energy installation supply taking its heat in a nuclear source as early as possible. (M.B.) [French] Le Commissariat a l'Energie Atomique (dans le cadre du plan quinquennal) a entre autres objectifs, la realisation des deux premiers reacteurs francais moderes au graphite. La construction du reacteur G-1 a Marcoule, premiere pile plutonigene francaise, est realise afin qu'il puisse diverger au debut de 1956 et atteindre sa pleine puissance au debut du second semestre de la meme annee. Dans ce rapport nous detaillerons les specificites du reacteur et en particulier son systeme de refroidissement et de recuperation d'energie. Le reacteur G-1 etant essentielement destine a permettre aux techniciens francais d'etudier le plus tot possible le comportement d'une installation productrice d'energie empruntant sa chaleur a une source nucleaire. (M.B.)

Bcl-2 and Bcl-xL overexpression inhibits cytochrome c release, activation of multiple caspases, and virus release following coxsackievirus B3 infection

International Nuclear Information System (INIS)

Carthy, Christopher M.; Yanagawa, Bobby; Luo Honglin; Granville, David J.; Yang, Decheng; Cheung, Paul; Cheung, Caroline; Esfandiarei, Mitra; Rudin, Charles M.; Thompson, Craig B.; Hunt, David W.C.; McManus, Bruce M.

2003-01-01

Coxsackievirus B3, a cytopathic virus in the family Picornaviridae, induces degenerative changes in host cell morphology. Here we demonstrate cytochrome c release and caspases-2, -3, -6, -7, -8, and -9 processing. Enforced Bcl-2 and Bcl-xL expression markedly reduced release of cytochrome c, presentation of the mitochondrial epitope 7A6, and depressed caspase activation following infection. In comparison, cell death using TRAIL ligand caused caspase-8 processing prior to cytochrome c release and executioner caspases and cell death was only partially rescued by Bcl-2 and Bcl-xL overexpression. Disruption of the mitochondrial inner membrane potential following CVB3 infection was not inhibited by zVAD.fmk treatment. Bcl-2 or Bcl-xL overexpression or zVAD.fmk treatment delayed the loss of host cell viability and decreased progeny virus release following infection. Our data suggest that mitochondrial release of cytochrome c may be an important early event in caspase activation in CVB3 infection, and, as such, may contribute to the loss of host-cell viability and progeny virus release

Achievements of European projects on membrane reactor for hydrogen production

NARCIS (Netherlands)

di Marcoberardino, G.; Binotti, M.; Manzolini, G.; Viviente, J.L.; Arratibel Plazaola, A.; Roses, L.; Gallucci, F.

2017-01-01

Membrane reactors for hydrogen production can increase both the hydrogen production efficiency at small scale and the electric efficiency in micro-cogeneration systems when coupled with Polymeric Electrolyte Membrane fuel cells. This paper discusses the achievements of three European projects

Tasks related to increase of RA reactor exploitation and experimental potential, 03. Crane for handling the vertical experimental channels of the RA reactor - design project

International Nuclear Information System (INIS)

Pavicevic, M.

1963-07-01

Within the work related to improvement of experimental potential of the RA reactor, this document describes the design project of the new crane for handling the vertical experimental channels of the RA reactor, engineering drawings of the crane main elements, mechanical part, design project of the electrical part of the crane and cost estimation

The International Science and Technology Center (ISTC) and ISTC projects related to research reactors. Information review

International Nuclear Information System (INIS)

Tocheniy, L.; Rudneva, V.Ya.

1998-01-01

1. ISTC - history, activities, outlook: The ISTC is an intergovernmental organization established by agreement between the Russian Federation, the European Union, Japan, and the United States. Since 1994, Finland, Sweden, Norway, Georgia, Armenia, Belarus, Kazakhstan and the Kyrgyz Republic have acceded to the Agreement and Statute. At present, the Republic of Korea is finishing the process of accession to the ISTC. All work of the ISTC is aimed at the goals defined in the ISTC Agreement: - To give CIS weapons scientists, particularly those who possess knowledge and skills related to weapons of mass destruction and their delivery systems, the opportunities to redirect their talents to peaceful activities; - To contribute to solving national and international technical problems; - To support the transition to market-based economies; - To support basic and applied research; - To help integrate CIS weapons scientists into the international scientific community. The projects may be funded both through governmental funds of the Funding Parties specified for the ISTC, and by organizations, nominated as Funding Partners of the ISTC. According to the ISTC Statute, approved by the appropriate national organizations, funds used within ISTC projects are exempt from CIS taxes. As of March 1998, more than 1500 proposals had been submitted to the Center, of which 541 were approved for funding, for a total value of approximately US dollars 165 million. The number of scientists and engineers participating in the projects is more than 17,000. 2. Projects Related to Research Reactors: There are about 20 funded and as yet non-funded projects related to various problems of research reactors. Many of them address safety issues. Information review of the results and plans of both ongoing projects and as yet non-funded proposals related to research reactors will be presented with the aim assisting international researchers to establish partnerships or collaboration with ISTC projects

The decommissioning of a research reactor in the USA: A case study from planning to site release

International Nuclear Information System (INIS)

Boing, L.E.

1997-01-01

Argonne National Laboratory (ANL) has completed the D ampersand D of the Experimental Boiling Water Reactor (EBWR). The project consisted of the decontamination and/or packaging as radioactive waste the reactor vessel and internals, contaminated piping systems, miscellaneous tanks, pumps, and associated equipment. The dismantling process involved the removal and size reduction of equipment and associated plumbing, ductwork, drain lines, etc. Size reduction of reactor vessel internals was performed in the fuel pool. All radioactive and mixed waste was packaged and manifested. A thorough survey of the facility was performed after the removal of contaminated and activated material. Non-radioactive waste was disposed of in the ANL landfill or recycled as appropriate. The EBWR D ampersand D project was divided into four phases. Phases I and II were completed by ANL personnel, while Phases III and IV were done by a contractor under ANL management. The final survey was performed by the contractor, while the verification survey was performed by ANL. The project lasted 118 months. Phase I was initiated in April 1986 and the final report was issued February 1996. The duration of the project was driven by the availability of funding for decommissioning. Total exposure to project personnel was 208.7 person-mSv (20.87 person-rem), with no personnel exceeding the EBWR project dose limit of 15 mSv (1.5 rem)

Effluent releases at the TRIGA reactor facility

Energy Technology Data Exchange (ETDEWEB)

Whittemore, W L [General Atomic Co., San Diego, CA (United States)

1974-07-01

The principal effluent from the operating TRIGA reactors in our facility is argon-41. As monitored by a recording gas and particulate stack monitor, the values shown in the table, the Mark III operating 24 hours per day for very long periods produced the largest amount of radioactive argon. The quantity of 23.7 Ci A-41 when diluted by the normal reactor room ventilation system corresponded to 1.45 x 10{sup -6} {mu}Ci/cc. As diluted in the roof stack stream and the reactor building wake, the concentration immediately outside the reactor building was 25% MPC for an unrestricted area. The continued dilution of this effluent resulted in a concentration of a few percent MPC at the site boundary (unrestricted area) 350 meters from the reactor. (author)

Removal of Cr(VI) from wastewaters at semi-industrial electrochemical reactors with rotating ring electrodes

International Nuclear Information System (INIS)

Rodriguez R, Miriam G.; Mendoza, Victor; Puebla, Hector; Martinez D, Sergio A.

2009-01-01

In Mexico, most of the electroplating and textile industries are small facilities and release relatively large amounts of hexavalent chromium (Cr(VI)) in surface waters. In this work, the results obtained during the operation of a batch reactor with a capacity of 170 L, and three electrochemical flow reactors-in-series system with a total capacity of 510 L (both using iron rotating ring electrodes to remove Cr(VI) from wastewaters) are presented. The reactors were scaled up from a laboratory reactor to a semi-industrial level, based on the similarity (dynamical, geometrical and electrochemical). An empirical Cr(VI) removal model was validated in batch and continuous reactors at different operating conditions. Cr(VI) concentration of the industrial wastewaters was reduced from about 500 mg/L to values lower than 0.5 mg/L. A very important parameter that affects the process is the pH, which affects the solubility of the Fe(III). Finally, the electrochemical treated wastewater can be reused

Removal of Cr(VI) from wastewaters at semi-industrial electrochemical reactors with rotating ring electrodes

Energy Technology Data Exchange (ETDEWEB)

Rodriguez R, Miriam G. [Depto. Energia, Universidad Autonoma Metropolitana-Azcapotzalco, Av. San Pablo 180, Azcapotzalco, CP 07740, Mexico D.F. (Mexico); Mendoza, Victor [Depto. Electronica, Universidad Autonoma Metropolitana-Azcapotzalco, Av. San Pablo 180, Azcapotzalco, CP 07740, Mexico D.F. (Mexico); Puebla, Hector [Depto. Energia, Universidad Autonoma Metropolitana-Azcapotzalco, Av. San Pablo 180, Azcapotzalco, CP 07740, Mexico D.F. (Mexico); Martinez D, Sergio A. [Depto. Energia, Universidad Autonoma Metropolitana-Azcapotzalco, Av. San Pablo 180, Azcapotzalco, CP 07740, Mexico D.F. (Mexico)], E-mail: samd@correo.azc.uam.mx

2009-04-30

In Mexico, most of the electroplating and textile industries are small facilities and release relatively large amounts of hexavalent chromium (Cr(VI)) in surface waters. In this work, the results obtained during the operation of a batch reactor with a capacity of 170 L, and three electrochemical flow reactors-in-series system with a total capacity of 510 L (both using iron rotating ring electrodes to remove Cr(VI) from wastewaters) are presented. The reactors were scaled up from a laboratory reactor to a semi-industrial level, based on the similarity (dynamical, geometrical and electrochemical). An empirical Cr(VI) removal model was validated in batch and continuous reactors at different operating conditions. Cr(VI) concentration of the industrial wastewaters was reduced from about 500 mg/L to values lower than 0.5 mg/L. A very important parameter that affects the process is the pH, which affects the solubility of the Fe(III). Finally, the electrochemical treated wastewater can be reused.

PWR-GALE, Radioactive Gaseous Release and Liquid Release from PWR

International Nuclear Information System (INIS)

Chandrasekaran, T.; Lee, J.Y.; Willis, C.A.

1988-01-01

1 - Description of program or function: The PWR-GALE (Boiling Water Reactor Gaseous and Liquid Effluents) Code is a computerized mathematical model for calculating the release of radioactive material in gaseous and liquid effluents from pressurized water reactors (PWRs). The calculations are based on data generated from operating reactors, field tests, laboratory tests, and plant-specific design considerations incorporated to reduce the quantity of radioactive materials that may be released to the environment. 2 - Method of solution: GALE calculates expected releases based on 1) standardized coolant activities derived from ANS Standards 18.1 Working Group recommendations, 2) release and transport mechanisms that result in the appearance of radioactive material in liquid and gaseous waste streams, 3) plant-specific design features used to reduce the quantities of radioactive materials ultimately released to the environs, and 4) information received on the operation of nuclear power plants. 3 - Restrictions on the complexity of the problem: The liquid release portion of GALE uses subroutines taken from the ORIGEN (CCC-217) to calculate radionuclide buildup and decay during collection, processing, and storage of liquid radwaste. Memory requirements for this part of the program are determined by the large nuclear data base accessed by these subroutines

Latest feedback from a major reactor vessel dismantling project

International Nuclear Information System (INIS)

Boucau, J.; Segerud, P.; Sanchez, M.; Garcia, R.

2015-01-01

Westinghouse performed two large segmentation projects in 2010-2013 and then 2013-2015 at the Jose Cabrera nuclear power plant in Spain. The power plant is located in Almonacid de Zorita, 43 miles east of Madrid, Spain and was in operation between 1968 and 2006. This paper will describe the sequential steps required to prepare, segment, separate, and package the individual component segments using under water mechanical techniques. The paper will also include experiences and lessons learned that Westinghouse has collected from the activities performed during the reactor vessel and vessel internals segmentation projects. (authors)

FIPRED Project - Experiments and calculations

International Nuclear Information System (INIS)

Ohai, D.; Dumitrescu, I.; Doca, C.; Meleg, T.; Benga, D.

2009-01-01

Full text: The FIPRED (Fission Products Release from Debris Bed) Project was developed by INR in the framework of EC FP6 SARNET (2004-2008) and will be continued in EC FP6 SARNET2 (2009-2013). The project objective is the evaluation of fission product release from debris bed resulted after reactor severe accident by natural UO 2 sintered pellets self disintegration by oxidation. A large experimental program was performed covering the main parameters influencing granulometric distribution of powders (fragments) resulted from UO 2 sintered pellets self disintegration by air oxidation. The paper presents experimental results obtained and material equation obtained by mathematical calculations. (authors)

Nuclear data evaluation and group constant generation for reactor analysis

Energy Technology Data Exchange (ETDEWEB)

Kim, Jung Do; Lee, Jong Tae; Min, Byung Joo; Gil, Choong Sup [Korea Atomic Energy Research Inst., Daeduk (Korea, Republic of)

1991-01-01

In nuclear or shielding design analysis for reactors or other facilities, nuclear data are one of the primary importances. Research project for nuclear data evaluation and their effective applications has been continuously performed. The objectives of this project are (1) to compile the latest evaluated nuclear data files, (2) to establish their processing code systems, and (3) to evaluate the multi- group constant library using the newly compiled data files and the code systems. As the results of this project, ENDF/B-VI Supplementary File including important nuclides, JENDL-3.1 and JEF-1 were compiled, and ENDF-6 international computer file format for evaluated nuclear data and its processing system NJOY89.31 were tested with ENDF/B-VI data. In order to test an applicability of the newly released data to thermal reactor problems, a number of benchmark calculations were performed, and the results were analyzed. Since preliminary benchmark testing of thermal reactor problems have been made the newly compiled data are expected to be positively used to develop advanced reactors. (Author).

Nuclear data evaluation and group constant generation for reactor analysis

International Nuclear Information System (INIS)

Kim, Jung Do; Lee, Jong Tae; Min, Byung Joo; Gil, Choong Sup

1991-01-01

In nuclear or shielding design analysis for reactors or other facilities, nuclear data are one of the primary importances. Research project for nuclear data evaluation and their effective applications has been continuously performed. The objectives of this project are (1) to compile the latest evaluated nuclear data files, (2) to establish their processing code systems, and (3) to evaluate the multi- group constant library using the newly compiled data files and the code systems. As the results of this project, ENDF/B-VI Supplementary File including important nuclides, JENDL-3.1 and JEF-1 were compiled, and ENDF-6 international computer file format for evaluated nuclear data and its processing system NJOY89.31 were tested with ENDF/B-VI data. In order to test an applicability of the newly released data to thermal reactor problems, a number of benchmark calculations were performed, and the results were analyzed. Since preliminary benchmark testing of thermal reactor problems have been made the newly compiled data are expected to be positively used to develop advanced reactors. (Author)

Hanford Site 100-N Area In Situ Bioremediation of UPR-100-N-17, Deep Petroleum Unplanned Release - 13245

International Nuclear Information System (INIS)

Saueressig, Daniel G.

2013-01-01

In 1965 and 1966, approximately 303 m 3 of Number 2 diesel fuel leaked from a pipeline used to support reactor operations at the Hanford Site's N Reactor. N Reactor was Hanford's longest operating reactor and served as the world's first dual purpose reactor for military and power production needs. The Interim Action Record of Decision for the 100-N Area identified in situ bioremediation as the preferred alternative to remediate the deep vadose zone contaminated by this release. A pilot project supplied oxygen into the vadose zone to stimulate microbial activity in the soil. The project monitored respiration rates as an indicator of active biodegradation. Based on pilot study results, a full-scale system is being constructed and installed to remediate the vadose zone contamination. (authors)

Research reactor decommissioning experience - concrete removal and disposal -

International Nuclear Information System (INIS)

Manning, Mark R.; Gardner, Frederick W.

1990-01-01

Removal and disposal of neutron activated concrete from biological shields is the most significant operational task associated with research reactor decommissioning. During the period of 1985 thru 1989 Chem-Nuclear Systems, Inc. was the prime contractor for complete dismantlement and decommissioning of the Northrop TRIGA Mark F, the Virginia Tech Argonaut, and the Michigan State University TRIGA Mark I Reactor Facilities. This paper discusses operational requirements, methods employed, and results of the concrete removal, packaging, transport and disposal operations for these (3) research reactor decommissioning projects. Methods employed for each are compared. Disposal of concrete above and below regulatory release limits for unrestricted use are discussed. This study concludes that activated reactor biological shield concrete can be safely removed and buried under current regulations

Radionuclide releases to the Columbia River from Hanford Operations, 1944--1971

International Nuclear Information System (INIS)

Heeb, C.M.; Bates, D.J.

1994-05-01

The purpose of the Hanford Environmental Dose Reconstruction (HEDR) Project is to estimate the radiation dose that individuals could have received as a result of radionuclide emissions since 1944 from the Hanford Site. One source of radionuclide releases to the Columbia River was from production reactor operations. This report provides a quantitative estimate of the amount of radioactivity released each month (1944--1971) to the Columbia River from eleven radionuclides as well as from gross beta activity

Sandia Pulse Reactor-IV Project

International Nuclear Information System (INIS)

Reuscher, J.A.

1983-01-01

Sandia National Laboratories has developed, designed and operated fast burst reactors for over 20 years. These reactors have been used for a variety of radiation effects programs. During this period, programs have required larger irradiation volumes primarily to expose complex electronic systems to postulated threat environments. As experiment volumes increased, a new reactor was built so that these components could be tested. The Sandia Pulse Reactor-IV is a logical evolution of the two decades of fast burst reactor development at Sandia

Advanced neutron source project

International Nuclear Information System (INIS)

Gorynina, L.V.; Proskuryakov, S.F.; Tishchenko, V.A.; Uzhanova, V.V.

1991-01-01

The project of the ANS improved neutron source intended for fundamental researches in nuclear physics and materials testing is considered. New superhigh-flux heavy-water 350 MW reactor is used for the source creation. The standard fuel is uranium silicide (U 3 Si 2 ). Reactor core volume equals 67.4 l and average power density is 4.9 MW/l. Neutron flux density is 10 16 neutron/(cm 2 xs). The facility construction begin is planned for 1996. The first experiments should be accomplished in 2000

Influence of corium oxidation on fission product release from molten pool

Energy Technology Data Exchange (ETDEWEB)

Bechta, S.V., E-mail: bechta@sbor.spb.s [Alexandrov Scientific-Research Institute of Technology (NITI), Sosnovy Bor (Russian Federation); Krushinov, E.V.; Vitol, S.A.; Khabensky, V.B.; Kotova, S.Yu.; Sulatsky, A.A. [Alexandrov Scientific-Research Institute of Technology (NITI), Sosnovy Bor (Russian Federation); Gusarov, V.V.; Almyashev, V.I. [Grebenschikov Institute of Silicate Chemistry of the Russian Academy of Sciences (ISC RAS), St. Petersburg (Russian Federation); Ducros, G.; Journeau, C. [CEA, DEN, Cadarache, F-13108 St. Paul lez Durance (France); Bottomley, D. [Joint Research Centre Institut fuer Transurane (ITU), Karlsruhe (Germany); Clement, B. [Institut de Radioprotection et Surete Nucleaire (IRSN), St. Paul lez Durance (France); Herranz, L. [CIEMAT, Madrid (Spain); Guentay, S. [PSI, Wuerenlingen (Switzerland); Trambauer, K. [GRS, Muenchen (Germany); Auvinen, A. [VTT, Espoo (Finland); Bezlepkin, V.V. [SPbAEP, St. Petersburg (Russian Federation)

2010-05-15

Qualitative and quantitative determination of the release of low-volatile fission products and core materials from molten oxidic corium was investigated in the EVAN project under the auspices of ISTC. The experiments carried out in a cold crucible with induction heating and RASPLAV test facility are described. The results are discussed in terms of reactor application; in particular, pool configuration, melt oxidation kinetics, critical influence of melt surface temperature and oxidation index on the fission product release rate, aerosol particle composition and size distribution. The relevance of measured high release of Sr from the molten pool for the reactor application is highlighted. Comparisons of the experimental data with those from the COLIMA CA-U3 test and the VERCORS tests, as well as with predictions from IVTANTHERMO and GEMINI/NUCLEA codes are made. Recommendations for further investigations are proposed following the major observations and discussions.

European supercritical water cooled reactor (HPLWR Phase 2 project)

International Nuclear Information System (INIS)

Schulenberg, Thomas; Starflinger, Joerg; Marsault, Philippe; Bittermann, Dietmar; Maraczy, Czaba; Laurien, Eckart; Lycklama, Jan Aiso; Anglart, Henryk; Andreani, Michele; Ruzickova, Mariana; Heikinheimo, Liisa

2010-01-01

The High Performance Light Water Reactor (HPLWR), how the European Supercritical Water Cooled Reactor is called, is a pressure vessel type reactor operated with supercritical water at 25 MPa feedwater pressure and 500 deg C maximum core outlet temperature. It is designed and analyzed by a European consortium of 13 partners from 8 Euratom member states in the second phase of the HPLWR project. Most emphasis has been laid on a core with a thermal neutron spectrum, consisting of small, housed fuel assemblies with 40 fuel pins each and a central water box to improve the neutron moderation despite the low coolant density. Peak cladding temperatures of the fuel rods have been minimized by heating up the coolant in three steps with intermediate coolant mixing. The innovative core design with upward and downward flow through its assemblies has been studied with neutronic, thermal-hydraulic and stress analyses and has been reviewed carefully in a mid-term assessment. The containment design with its safety and residual heat removal systems is based on the latest boiling water reactor concept, but with different passive high pressure coolant injection systems to cause a forced convection through the core. The design concept of the steam cycle is indicating the envisaged efficiency increase to around 44%. Moreover, it provides the constraints to design the components of the balance of the plant. The project is accompanied by numerical studies of heat transfer of supercritical water in fuel assemblies and by material tests of candidate cladding alloys, performed by the consortium and supported by additional tests of the Joint Research Centre of the European Commission. An overview of results achieved up to now, given in this paper, is illustrating the latest scientific and technological advances. (author)

Determination of Source Term for an Annual Stack Release of Gas Reactor G.A. Siwabessy

International Nuclear Information System (INIS)

Sudiyati; Syahrir; Unggul Hartoyo; Nugraha Luhur

2008-01-01

Releases of radionuclide from the reactor are noble gases, halogenides and particulates. The measurements were carried out directly on the air monitoring system of the stack. The results of these measurements are compared with the annual Source-Term data from the Safety Analyses report (SAR) of RSG-GAS. The measurement results are smaller than the data reported in SAR document. (author)

The French-German common safety approach for future reactors

International Nuclear Information System (INIS)

Birkhofer, A.; Chevet, P.F.

1995-01-01

A common safety approach has been defined for future electronuclear plants in the framework of the French-German European Pressurised water Reactor (EPR) project. Improvements in the domain of containment are required in future reactors conception to prevent any risk of core fusion under high and low pressure. Another objective is to reduce significantly the radioactive releases due to other accidents in order to reduce spatial and temporal environmental and human protection procedures. Protection against external aggressions (plane fall, explosions, earthquakes,..), prevention of pipe rupture in the primary circuits, limitation of hydrogen production in the case of water-zirconium complete reaction, cooling of the reactor in the case of core fusion, and radiologic consequences of accidents are the main points discussed by the French-German safety authorities to define the common safety standards of the EPR project. (J.S.)

Decontamination and decommissioning of the Argonne Thermal Source Reactor at Argonne National Laboratory - East project final report

International Nuclear Information System (INIS)

Fellhauer, C.; Garlock, G.; Mathiesen, J.

1998-01-01

The ATSR D and D Project was directed toward the following goals: (1) Removal of radioactive and hazardous materials associated with the ATSR Reactor facility; (2) Decontamination of the ATSR Reactor facility to unrestricted use levels; and (3)Documentation of all project activities affecting quality (i.e., waste packaging, instrument calibration, audit results, and personnel exposure). These goals had been set in order to eliminate the radiological and hazardous safety concerns inherent in the ATSR Reactor facility and to allow, upon completion of the project, unescorted and unmonitored access to the area. The reactor aluminum, reactor lead, graphite piles in room E-111, and the contaminated concrete in room E-102 were the primary areas of concern. NES, Incorporated (Danbury, CT) characterized the ATSR Reactor facility from January to March 1998. The characterization identified a total of thirteen radionuclides, with a total activity of 64.84 mCi (2.4 GBq). The primary radionuclides of concern were Co 60 , Eu 152 , Cs 137 , and U 238 . No additional radionuclides were identified during the D and D of the facility. The highest dose rates observed during the project were associated with the reactor tank and shield tank. Contact radiation levels of 30 mrem/hr (0.3 mSv/hr) were measured on reactor internals during dismantlement of the reactor. A level of 3 mrem/hr (0.03 mSv/hr) was observed in a small area (hot spot) in room E-102. DOE Order 5480.2A establishes the maximum whole body exposure for occupational workers at 5 rem/yr (50 mSv/yr); the administrative limit at ANL-E is 1 rem/yr (10 mSv/yr)

Systemic model for the aid for operating of the reactor Siloe; Modelisation systeme pour l`aide a l`exploitation du reacteur de recherche Siloe

Energy Technology Data Exchange (ETDEWEB)

Royer, J.C.; Moulin, V.; Monge, F. [CEA Centre d`Etudes de Grenoble, 38 (France). Direction des Reacteurs Nucleaires; Baradel, C. [ITMI APTOR, 38 - Meylan (France)

1995-12-31

The Service of the Reactor Siloe (CEA/DRN/DRE/SRS), fully aware of the abilities and knowledge of his teams in the field of research reactor operating, has undertaken a project of knowledge engineering in this domain. The following aims have been defined: knowledge capitalization for the installation in order to insure its perenniality and valorization, elaboration of a project for the aid of the reactor operators. This article deals with the different actions by the SRS to reach the aims: realization of a technical model for the operation of the Siloe reactor, development of a knowledge-based system for the aid for operating. These actions based on a knowledge engineering methodology, SAGACE, and using industrial tools will lead to an amelioration of the security and the operating of the Siloe reactor. (authors). 13 refs., 7 figs.

Reduction of releases of radioactive effluents from light-water-power-reactors in Japan

International Nuclear Information System (INIS)

Yoshida, Y.; Itakura, T.; Kanai, T.

1977-01-01

Japan Atomic Energy Commission established the dose objectives to the population around the light-water-reactors in May, 1975, based on the ''ALAP'' concept. These values are respectively, 5 mrems per year for total body and 15 mrems per year for thyroid of an individual in the critical group in the environs, due to both gaseous and liquid effluents from LWRs in one site. The present paper describes the implications of the dose objective values, control measures which have been adopted to reduce releases of radioactive materials and related technical developments in Japan. The main control measures for reduction of radioactive gaseous effluents are an installation of a charcoal gas holdup system for decay of noble gases and a supply of clean steam for the gland seal of a turbine in BWR, and a storage tank system allowing decay of noble gases in PWR. For liquid effluents are taken measures to re-use them as the primary coolant. Consequently, the amounts of radioactivity released to the environment from any LWR during normal operation have been maintained under the level to meet the above dose objective values. For research reactors, reduction of release of effluents has also been carried out in a similar way to LWRs. In order to establish the techniques applicable for further reduction, studies are being made on the control measures to reduce leakage of radioiodine, an apparatus for removal of krypton, the treatment of laundry waste and measures to remove the crud in the primary coolant. Presentation is also made on the energy-integrated gas monitor for gaseous effluent and systems of measuring γ dose from radioactive cloud descriminating from natural background, which have been developed for effective monitoring thus reduced environmental dose

Quality assurance in technology development for The Clinch River Breeder Reactor Plant Project

International Nuclear Information System (INIS)

Anderson, J.W.

1980-01-01

The Clinch River Breeder Reactor Plant Project is the nation's first large-scale demonstration of the Liquid Metal Fast Breeder Reactor (LMFBR) concept. The Project has established an overall program of plans and actions to assure that the plant will perform as required. The program has been established and is being implemented in accordance with Department of Energy Standard RDT F 2-2. It is being applied to all parts of the plant, including the development of technology supporting its design and licensing activity. A discussion of the program as it is applied to development is presented

IAEA fast reactor knowledge preservation initiative. Project focus: KNK-II reactor, Karlsruhe, Germany

International Nuclear Information System (INIS)

2004-08-01

This Working Material (including the attached CD-ROM) documents progress made in the IAEA's initiative to preserve knowledge in the fast reactor domain. The brochure describes briefly the context of the initiative and gives an introduction to the contents of the CD-ROM. In 2003/2004 a first focus of activity was concentrated on the preservation of knowledge related to the KNK-II experimental fast reactor in Karlsruhe, Germany. The urgency of this project was given by the impending physical destruction of the installation, including the office buildings. Important KNK-II documentation was brought to safety and preserved just in time. The CD-ROM contains the full texts of 264 technical and scientific documents describing research, development and operating experience gained with the KNK-II installation over a period of time from 1965 to 2002, extending through initial investigations, 17 years of rich operating experience, and final shutdown and decommissioning. The index to the documents on the CD-ROM is printed at the end of this booklet in chronological order and is accessible on the CD by subject index and chronological index. The CD-ROM contains in its root directory also the document 'fr c lassification.pdf' which describes the classification system used for the present collection of documents on the fast reactor KNK-II

Project plan for the decontamination and decommissioning of the Argonne National Laboratory Experimental Boiling Water Reactor

International Nuclear Information System (INIS)

Boing, L.E.

1989-12-01

In 1956, the Experimental Boiling Water Reactor (EBWR) Facility was first operated at Argonne National Laboratory (ANL) as a test reactor to demonstrate the feasibility of operating an integrated power plant using a direct cycle boiling water reactor as a heat source. In 1967, ANL permanently shut down the EBWR and placed it in dry lay-up. This project plan presents the schedule and organization for the decontamination and decommissioning of the EBWR Facility which will allow it to be reused by other ANL scientific research programs. The project total estimated cost is $14.3M and is projected to generate 22,000 cubic feet of low-level radioactive waste which will be disposed of at an approved DOE burial ground. 18 figs., 3 tabs

Project plan for the decontamination and decommissioning of the Argonne National Laboratory Experimental Boiling Water Reactor

Energy Technology Data Exchange (ETDEWEB)

Boing, L.E.

1989-12-01

In 1956, the Experimental Boiling Water Reactor (EBWR) Facility was first operated at Argonne National Laboratory (ANL) as a test reactor to demonstrate the feasibility of operating an integrated power plant using a direct cycle boiling water reactor as a heat source. In 1967, ANL permanently shut down the EBWR and placed it in dry lay-up. This project plan presents the schedule and organization for the decontamination and decommissioning of the EBWR Facility which will allow it to be reused by other ANL scientific research programs. The project total estimated cost is $14.3M and is projected to generate 22,000 cubic feet of low-level radioactive waste which will be disposed of at an approved DOE burial ground. 18 figs., 3 tabs.

Review of processes for the release of DOE real and non-real property for reuse and recycle

International Nuclear Information System (INIS)

Ranek, N.L.; Kamboj, S.; Hensley, J.; Chen, S.Y.; Blunt, D.

1997-11-01

This report summarizes the underlying historical and regulatory framework supporting the concept of authorizing release for restricted or unrestricted reuse or recycle of real and non-real U.S. Department of Energy (DOE) properties containing residual radioactive material. Basic radiation protection principles as recommended by the International Commission on Radiological Protection are reviewed, and international initiatives to investigate radiological clearance criteria are reported. Applicable requirements of the U.S. Nuclear Regulatory Commission, the Environmental Protection Agency, DOE, and the State of Washington are discussed. Several processes that have been developed for establishing cleanup and release criteria for real and non-real DOE property containing residual radioactive material are presented. Examples of DOE real property for which radiological cleanup criteria were established to support unrestricted release are provided. Properties discussed include Formerly Utilized Sites Remedial Action Project sites, Uranium Mill Tailings Remedial Action Project sites, the Shippingport decommissioning project, the south-middle and south-east vaults in the 317 area at Argonne National Laboratory, the Heavy Water Components Test Reactor at DOE's Savannah River Site, the Experimental Boiling Water Reactor at Argonne National Laboratory, and the Weldon Spring site. Some examples of non-real property for which DOE sites have established criteria to support unrestricted release are also furnished. 10 figs., 4 tabs

Hanford Site 100-N Area In Situ Bioremediation of UPR-100-N-17, Deep Petroleum Unplanned Release - 13245

Energy Technology Data Exchange (ETDEWEB)

Saueressig, Daniel G. [Washington Closure Hanford, 2620 Fermi, Richland, Washington, 99354 (United States)

2013-07-01

In 1965 and 1966, approximately 303 m{sup 3} of Number 2 diesel fuel leaked from a pipeline used to support reactor operations at the Hanford Site's N Reactor. N Reactor was Hanford's longest operating reactor and served as the world's first dual purpose reactor for military and power production needs. The Interim Action Record of Decision for the 100-N Area identified in situ bioremediation as the preferred alternative to remediate the deep vadose zone contaminated by this release. A pilot project supplied oxygen into the vadose zone to stimulate microbial activity in the soil. The project monitored respiration rates as an indicator of active biodegradation. Based on pilot study results, a full-scale system is being constructed and installed to remediate the vadose zone contamination. (authors)

Mitigation of release of volatile iodine species during severe reactor accidents - a novel reliable process of safety technology

International Nuclear Information System (INIS)

Guentay, S.; Bruchertseifer, H.

2010-01-01

In severe accidents, a significant risk for public health may be generated as a result of release of the gaseous iodine species into the environment through the containment leaks or containment venting filter systems with low retention efficiency. The elemental iodine and volatile organic iodides are the main gaseous iodine species in the containment. Potential release of large quantities of gaseous elemental iodine from the reactor coolant system or its radiolytic generation in the containment sump constitute the key source of gaseous elemental iodine in containment atmosphere. Iodine paint reactions as well as the reaction of iodine with organic residuals in sump water are the main mechanisms for the generation of high volatile organic iodides in the containment. Although very much desired, significant research activities conducted in 70's unfortunately did not create any technically feasible solution to mitigate iodine release into the environment under prevailing conditions. Development of a process leading to a fast, comprehensive and reliable retention of volatile iodine species in aqueous solution with an aim to implement for the severe accident management applications has been subject of a research project in the recent years at Paul Scherrer Institut. The process developed utilizes simultaneous use of two customary technical chemical additives in an aqueous solution. The results of the experimental program have demonstrated a fast and reliable destruction of high volatile organic iodine species and fast reduction of elemental iodine into iodide ions in aqueous solutions and an efficient mitigation of the re-formation of gaseous iodine from iodide ions. Investigations covered a broad range of anticipated severe accident conditions in the containment. The project additionally focused on possible application of the process to existing containment venting filter systems, specifically as a passive add-on for back-fitting. This paper describes the process

The activities of the committee 'Kernreaktorregelung' (nuclear reactor control) in the past few years and future projects

International Nuclear Information System (INIS)

Knecht, O.

1976-01-01

Results achieved so far and future projects are portrayed in detail: 1) VDI/VDE 3527-Graphical symbols for nuclear reactor control; 2) VDI/VDE 3528-Special terms and definitons for nuclear reactor control; 3) 8 data sheets on reactor control; 4) VDI/VDE 3530-Characterisation of reactor control rod drives. (orig./HP) [de

Super safe small reactor RAPID-L conceptual design and R and D. JAERI's nuclear research promotion program, H11-002 (Contract research)

Energy Technology Data Exchange (ETDEWEB)

Kambe, Mitsuru [Central Research Inst. of Electric Power Industry, Tokyo (Japan); Tsunoda, Hirokazu [Mitsubishi Research Inst., Inc., Tokyo (Japan); Mishima, Kaichiro [Kyoto Univ., Kyoto (Japan); Kawasaki, Akira [Tohoku Univ., School of Engineering, Sendai, Miyagi (Japan); Iwamura, Takamichi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2003-03-01

The 200 kWe uranium nitride fueled lithium cooled fast reactor 'RAPID-L' combined with thermoelectric power conversion system that can be operated unmanned without refueling for up to ten years has been demonstrated. The RAPID refueling concept enables quick and simplified refueling, and achieves plant design lifetime over 20 years. A significant advantage of the RAPID-L design, which does not require the use of control rods - is the introduction of the innovative reactivity control systems: lithium expansion module (LEM), lithium injection module (LIM) and lithium release module (LRM). LEM is the most promising candidate for improving inherent reactivity feedback. LEMs could realize burnup compensation. LIMs assure sufficient negative reactivity feedback in unprotected transients. LRMs enable an automated reactor startup by detecting the hot standby temperature of the primary coolant. All these systems use {sup 6}Li as liquid poison and are actuated by highly reliable physical properties (volume expansion of {sup 6}Li for LEM, and freeze seal melting for LIM and LRM). (author)

International Reactor Physics Experiment Evaluation (IRPhE) Project. IRPhE Handbook - 2015 edition

International Nuclear Information System (INIS)

Bess, John D.; Gullifor, Jim

2015-03-01

The purpose of the International Reactor Physics Experiment Evaluation (IRPhE) Project is to provide an extensively peer-reviewed set of reactor physics-related integral data that can be used by reactor designers and safety analysts to validate the analytical tools used to design next-generation reactors and establish the safety basis for operation of these reactors. This work of the IRPhE Project is formally documented in the 'International Handbook of Evaluated Reactor Physics Benchmark Experiments', a single source of verified and extensively peer-reviewed reactor physics benchmark measurements data. The evaluation process entails the following steps: Identify a comprehensive set of reactor physics experimental measurements data, Evaluate the data and quantify overall uncertainties through various types of sensitivity analysis to the extent possible, verify the data by reviewing original and subsequently revised documentation, and by talking with the experimenters or individuals who are familiar with the experimental facility, Compile the data into a standardized format, Perform calculations of each experiment with standard reactor physics codes where it would add information, Formally document the work into a single source of verified and peer reviewed reactor physics benchmark measurements data. The International Handbook of Evaluated Reactor Physics Benchmark Experiments contains reactor physics benchmark specifications that have been derived from experiments that were performed at nuclear facilities around the world. The benchmark specifications are intended for use by reactor designers, safety analysts and nuclear data evaluators to validate calculation techniques and data. Example calculations are presented; these do not constitute a validation or endorsement of the codes or cross-section data. The 2015 edition of the International Handbook of Evaluated Reactor Physics Benchmark Experiments contains data from 143 experimental series that were

Application of the Defense-in-Depth Concept in the Projects of New-Generation NPPs Equipped with VVER Reactors

Energy Technology Data Exchange (ETDEWEB)

Shvyryaev, Yu. V.; Morozov, V. B.; Kuchumov, A.Yu., E-mail: morozov@aep.ru [JSC Atomenergoproekt, Moscow (Russian Federation)

2014-10-15

The projects of new-generation NPPs equipped with VVER reactors are developed as projects the safety level of which is superior to that of NPPs that are currently in operation. The main design solutions adopted for implementing the defence-in-depth (DiD) concept in the projects of new-generation NPPs equipped with VVER reactors are briefly characterized in the paper. (author)

Substitution of the old console with a fully computerized one. Major maintenance and enhancements of the ventilation and air conditioning system of the reactor building. Research activities at the TRIGA L.E.N.A. plant in Pavia, Italy

International Nuclear Information System (INIS)

Orvini, E.; Piazzoli, A.; Borio, A.

2008-01-01

pulse power monitor, the new ICS will improve the capability for the pulsing operational mode of the reactor. The new ACFS is also operated under a computer control. The technical specifications of the new system are basically the same of the old one, but for a double air filtering in suction and emission from the reactor building, instead of a simple filtering of the external air. The design philosophy of the new system assures a fairly good filtering of the external air inlet (>95%) and a very good filtering of the air released in the atmosphere, thanks to absolute filters with an efficiency higher that 99.95%. This new solution goes definitively in the direction of increasing the safety level of the reactor for what concerns the potential consequences on the population due to an accidental release of radioactive products in the atmosphere. Both the upgrading activities required to undergo the evaluation of the Italian National Regulatory Commission for the reactor licence modification. The following data are supplied in 8 tables, as follows: - Operation Data (July 1998 - June 2000); - Number of Irradiation and of Irradiated Samples in Reactor Facilities; - Users of the L.E.N.A. Reactor Irradiation Facilities; - Activities at the L.E.N.A. Reactor; - Utilization Data by different Users; - Utilization Data for different Activities; - Survey of Fuel Elements elongation (1965 - 2000); - Fuel Elements of L.E.N.A. TRIGA Reactor

Functional hierarchy of two L domains in porcine endogenous retrovirus (PERV) that influence release and infectivity

International Nuclear Information System (INIS)

Marcucci, Katherine T.; Martina, Yuri; Harrison, Frank; Wilson, Carolyn A.; Salomon, Daniel R.

2008-01-01

The porcine endogenous retrovirus (PERV) Gag protein contains two late (L) domain motifs, PPPY and P(F/S)AP. Using viral release assays we demonstrate that PPPY is the dominant L domain involved in PERV release. PFAP represents a novel retroviral L domain variant and is defined by abnormal viral assembly phenotypes visualized by electron microscopy and attenuation of early PERV release as measured by viral genomes. PSAP is functionally dominant over PFAP in early PERV release. PSAP virions are 3.5-fold more infectious in vitro by TCID 50 and in vivo results in more RNA positive tissues and higher levels of proviral DNA using our human PERV-A receptor (HuPAR-2) transgenic mouse model [Martina, Y., Marcucci, K.T., Cherqui, S., Szabo, A., Drysdale, T., Srinivisan, U., Wilson, C.A., Patience, C., Salomon, D.R., 2006. Mice transgenic for a human porcine endogenous retrovirus receptor are susceptible to productive viral infection. J. Virol. 80 (7), 3135-3146]. The functional hierarchies displayed by PERV L domains, demonstrates that L domain selection in viral evolution exists to promote efficient viral assembly, release and infectivity in the virus-host context

Advanced nuclear reactor public opinion project

Energy Technology Data Exchange (ETDEWEB)

Benson, B.

1991-07-25

This Interim Report summarizes the findings of our first twenty in-depth interviews in the Advanced Nuclear Reactor Public Opinion Project. We interviewed 6 industry trade association officials, 3 industry attorneys, 6 environmentalists/nuclear critics, 3 state officials, and 3 independent analysts. In addition, we have had numerous shorter discussions with various individuals concerned about nuclear power. The report is organized into the four categories proposed at our April, 1991, Advisory Group meeting: safety, cost-benefit analysis, science education, and communications. Within each category, some change of focus from that of the Advisory Group has been required, to reflect the findings of our interviews. This report limits itself to describing our findings. An accompanying memo draws some tentative conclusions.

Advanced nuclear reactor public opinion project

International Nuclear Information System (INIS)

Benson, B.

1991-01-01

This Interim Report summarizes the findings of our first twenty in-depth interviews in the Advanced Nuclear Reactor Public Opinion Project. We interviewed 6 industry trade association officials, 3 industry attorneys, 6 environmentalists/nuclear critics, 3 state officials, and 3 independent analysts. In addition, we have had numerous shorter discussions with various individuals concerned about nuclear power. The report is organized into the four categories proposed at our April, 1991, Advisory Group meeting: safety, cost-benefit analysis, science education, and communications. Within each category, some change of focus from that of the Advisory Group has been required, to reflect the findings of our interviews. This report limits itself to describing our findings. An accompanying memo draws some tentative conclusions

Challenges Related to the Use of Liquid Metal and Molten Salt Coolants in Advanced Reactors. Report of the collaborative project COOL of the International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO)

International Nuclear Information System (INIS)

2013-05-01

The International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO) was launched in 2000, based on a resolution by the IAEA General Conference (GC(44)/RES/21). INPRO aims at helping to ensure that nuclear energy is available in the twenty-first century in a sustainable manner, and seeks to bring together all interested Member States, both technology holders and technology users, to jointly consider actions to achieve desired innovations. INPRO is taking care of the specific needs of developing countries. One of the aims of INPRO is to develop options for enhanced sustainability through promotion of technical and institutional innovations in nuclear energy technology through collaborative projects among IAEA Member States. Collaboration among INPRO members is fostered on selected innovative nuclear technologies to bridge technology gaps. Collaborative projects have been selected so that they complement other national and international R and D activities. The INPRO Collaborative Project COOL on Investigation of Technological Challenges Related to the Removal of Heat by Liquid Metal and Molten Salt Coolants from Reactor Cores Operating at High Temperatures investigated the technological challenges of cooling reactor cores that operate at high temperatures in advanced fast reactors, high temperature reactors and accelerator driven systems by using liquid metals and molten salts as coolants. The project was initiated in 2008 and was led by India; experts from Brazil, China, Germany, India, Italy and the Republic of Korea participated and provided chapters of this report. The INPRO Collaborative Project COOL addressed the following fields of research regarding liquid metal and molten salt coolants: (i) survey of thermophysical properties; (ii) experimental investigations and computational fluid dynamics studies on thermohydraulics, specifically pressure drop and heat transfer under different operating conditions; (iii) monitoring and control of coolant

I and C safety research at the OECD Halden reactor project

International Nuclear Information System (INIS)

Gran, B.A.

2007-01-01

The overall objective of the Halden Reactor Project research on software systems dependability is to contribute to the successful introduction of digital I and C systems into NPPs. When celebrating the 50 years of the Halden Project in 2008, about 100 written reports have been delivered within this research. This research covers a number of topics covering safety, reliability, validation and verification, quality assurance, risk assessment, requirement engineering, error propagation, qualitative and quantitative assessment. In the paper some activities are described, pinpointing the importance of good joint projects with organisations in the member countries

Radioactive releases into the environment under accidental conditions

International Nuclear Information System (INIS)

Beninson, D.

1976-01-01

Although accidents involving the release of radioactive materials and the unplanned exposure of people can occur at any stage of the nuclear fuel cycle, most attention has been focused on reactor accidents. Although no power reactor accidents involving exposure of the public have yet occured, it should be recognized that the probability of such accidental releases cannot be reduced to zero. Since the inventory of radioactive materials in power reactors is very large, it is usual to postulate, for safety assessments, that a release of fission products takes place in spite of all protective measures. This postulated release is of importance for reactor siting and for preparing emergency plans. (HP) [de

Reactor Physics

International Nuclear Information System (INIS)

Ait Abderrahim, A.

2002-01-01

SCK-CEN's Reactor Physics and MYRRHA Department offers expertise in various areas of reactor physics, in particular in neutron and gamma calculations, reactor dosimetry, reactor operation and control, reactor code benchmarking and reactor safety calculations. This expertise is applied in the Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 materials testing reactor dosimetry, and the preparation and interpretation of irradiation experiments by means of neutron and gamma calculations. The activities of the Fuzzy Logic and Intelligent Technologies in Nuclear Science programme cover several domains outside the department. Progress and achievements in these topical areas in 2001 are summarised

Reactor Physics

Energy Technology Data Exchange (ETDEWEB)

Ait Abderrahim, A

2001-04-01

The Reactor Physics and MYRRHA Department of SCK-CEN offers expertise in various areas of reactor physics, in particular in neutronics calculations, reactor dosimetry, reactor operation, reactor safety and control and non-destructive analysis of reactor fuel. This expertise is applied in the Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 reactor dosimetry, and the preparation and interpretation of irradiation experiments by means of neutron and gamma calculations. The activities of the Fuzzy Logic and Intelligent Technologies in Nuclear Science programme cover several domains outside the department. Progress and achievements in these topical areas in 2000 are summarised.

Reactor Physics

International Nuclear Information System (INIS)

Ait Abderrahim, A.

2001-01-01

The Reactor Physics and MYRRHA Department of SCK-CEN offers expertise in various areas of reactor physics, in particular in neutronics calculations, reactor dosimetry, reactor operation, reactor safety and control and non-destructive analysis of reactor fuel. This expertise is applied in the Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 reactor dosimetry, and the preparation and interpretation of irradiation experiments by means of neutron and gamma calculations. The activities of the Fuzzy Logic and Intelligent Technologies in Nuclear Science programme cover several domains outside the department. Progress and achievements in these topical areas in 2000 are summarised

Analysis of the TREAT loss-of-flow tests L6 and L7 using SAS3D

International Nuclear Information System (INIS)

Morris, E.E.; Simms, R.; Gruber, E.E.

1985-01-01

The TREAT loss-of-flow tests L6 and L7 have been analyzed using the SAS3D accident analysis code. The impetus for the analysis was the need for experimentally supported fuel motion modeling in whole core accident studies performed in support of licensing of the Clinch River Breeder Reactor Project. The input prescription chosen for the SAS3D/SLUMPY fuel motion model gave reasonable agreement with the test results. Tests L6 and L7, each conducted with a cluster of three fuel pins, were planned to simulate key events in the loss-of-flow accident scenario for the Clinch River homogeneous reactor

An estimation of exposure from gaseous and volatile radioactive effluents released from EWA reactor between 1971 and 1975

International Nuclear Information System (INIS)

Filipiak, B.; Nowicki, K.

1979-01-01

The paper gives an estimation of radiation doses for individuals due to gaseous radioactive effluents released from EWA reactor between 1971 and 1975. The doses were estimated for three organs, three groups of people: adults, teenagers and children and for three of the most important exposure paths: the external radiation from a passing cloud, inhalation and from milk ingestion. The results of calculations indicate that the radiation doses received by individuals living in the vicinity of EWA reactor were much below the limit doses or those due to the background radiation. (author)

A fission-fusion hybrid reactor in steady-state L-mode tokamak configuration with natural uranium

International Nuclear Information System (INIS)

Reed, Mark; Parker, Ronald R.; Forget, Benoit

2012-01-01

This work develops a conceptual design for a fusion-fission hybrid reactor operating in steady-state L-mode tokamak configuration with a subcritical natural or depleted uranium pebble bed blanket. A liquid lithium-lead alloy breeds enough tritium to replenish that consumed by the D-T fusion reaction. The fission blanket augments the fusion power such that the fusion core itself need not have a high power gain, thus allowing for fully non-inductive (steady-state) low confinement mode (L-mode) operation at relatively small physical dimensions. A neutron transport Monte Carlo code models the natural uranium fission blanket. Maximizing the fission power gain while breeding sufficient tritium allows for the selection of an optimal set of blanket parameters, which yields a maximum prudent fission power gain of approximately 7. A 0-D tokamak model suffices to analyze approximate tokamak operating conditions. This fission blanket would allow the fusion component of a hybrid reactor with the same dimensions as ITER to operate in steady-state L-mode very comfortably with a fusion power gain of 6.7 and a thermal fusion power of 2.1 GW. Taking this further can determine the approximate minimum scale for a steady-state L-mode tokamak hybrid reactor, which is a major radius of 5.2 m and an aspect ratio of 2.8. This minimum scale device operates barely within the steady-state L-mode realm with a thermal fusion power of 1.7 GW. Basic thermal hydraulic analysis demonstrates that pressurized helium could cool the pebble bed fission blanket with a flow rate below 10 m/s. The Brayton cycle thermal efficiency is 41%. This reactor, dubbed the Steady-state L-mode non-Enriched Uranium Tokamak Hybrid (SLEUTH), with its very fast neutron spectrum, could be superior to pure fission reactors in terms of breeding fissile fuel and transmuting deleterious fission products. It would likely function best as a prolific plutonium breeder, and the plutonium it produces could actually be more

Internal structure of reactor building for Madras Atomic Power Project

International Nuclear Information System (INIS)

Pandit, D.P.

1975-01-01

The structural configuration and analysis of structural elements of the internal structure of reactor building for the Madras Atomic Power Project has been presented. Two methods of analysis of the internal structure, viz. Equivalent Plane Frame and Finite Element Method, are explained and compared with the use of bending moments obtained. (author)

Design of project management system for 10 MW high temperature gas-cooled test reactor

International Nuclear Information System (INIS)

Zhu Yan; Xu Yuanhui

1998-01-01

A framework of project management information system (MIS) for 10 MW high temperature gas-cooled test reactor is introduced. Based on it, the design of nuclear project management information system and project monitoring system (PMS) are given. Additionally, a new method of developing MIS and Decision Support System (DSS) has been tried

High Temperature Gas-cooled Reactor Projected Markets and Scoping Economics

Energy Technology Data Exchange (ETDEWEB)

Larry Demick

2010-08-01

The NGNP Project has the objective of developing the high temperature gas-cooled reactor (HTGR) technology to supply high temperature process heat to industrial processes as a substitute for burning of fossil fuels, such as natural gas. Applications of the HTGR technology that have been evaluated by the NGNP Project for supply of process heat include supply of electricity, steam and high-temperature gas to a wide range of industrial processes, and production of hydrogen and oxygen for use in petrochemical, refining, coal to liquid fuels, chemical, and fertilizer plants.

Neutron thermalization in reactor lattice cells: An NPY-project report

International Nuclear Information System (INIS)

Stamm'ler, R.J.J.; Takac, S.M.; Weiss, Z.J.

1966-01-01

The NPY-Project is a joint research programme in reactor physics between Norway, Poland, Yugoslavia and the International Atomic Energy Agency. One of the tasks of the project was to make a theoretical and experimental investigation of the phenomena of neutron thermalization in lattice cells, and this work is covered by the present monograph. The different lattices of the zero-power assemblies in the NPY countries offered ample opportunity for the theoreticians and experimentalists to test and compare their methods, and the exchange of experiences was stimulating and valuable. 85 refs, 26 figs, 19 tabs

Reactor Physics

Energy Technology Data Exchange (ETDEWEB)

Ait Abderrahim, A

2002-04-01

SCK-CEN's Reactor Physics and MYRRHA Department offers expertise in various areas of reactor physics, in particular in neutron and gamma calculations, reactor dosimetry, reactor operation and control, reactor code benchmarking and reactor safety calculations. This expertise is applied in the Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 materials testing reactor dosimetry, and the preparation and interpretation of irradiation experiments by means of neutron and gamma calculations. The activities of the Fuzzy Logic and Intelligent Technologies in Nuclear Science programme cover several domains outside the department. Progress and achievements in these topical areas in 2001 are summarised.

PARIS project: Radiolytic oxidation of molecular iodine in containment during a nuclear reactor severe accident

Energy Technology Data Exchange (ETDEWEB)

Bosland, L. [Institut de Radioprotection et de Surete Nucleaire, DPAM, SEMIC, LETR - CEN Cadarache, BP 3, 13115 Saint Paul Lez Durance (France)], E-mail: loic.bosland@irsn.fr; Funke, F. [AREVA NP GmbH, Technical Center, P.O. Box 1109, D-91001 Erlangen (Germany); Girault, N. [Institut de Radioprotection et de Surete Nucleaire, DPAM, SEMIC, LETR - CEN Cadarache, BP 3, 13115 Saint Paul Lez Durance (France); Langrock, G. [AREVA NP GmbH, Technical Center, P.O. Box 1109, D-91001 Erlangen (Germany)

2008-12-15

In case of a hypothetical severe accident in a nuclear LWR (light water reactor), the high radiation fields reached in the reactor containment building due to the release of fission products from the reactor core could induce air radiolysis. The air radiolysis products could, in turn, oxidise gaseous molecular iodine into aerosol-borne iodine-oxygen-nitrogen compounds. Thereby, this reaction involves a change of iodine speciation and a decrease of iodine volatility in the reactor containment atmosphere. Kinetic data were produced within the PARIS project on the air radiolysis products formation and destruction, and on their reaction with molecular iodine, with the objective of developing and validating existing kinetic models. The current paper includes the non-iodine tests of the PARIS project whose objective was to determine the rates of formation and destruction of air radiolysis products in the presence of both structural containment surfaces (decontamination coating ('paint') and stainless steel), aerosol particles such as silver rich particles (issued from the control rods) in boundary conditions representative for LWR or PHEBUS facility containments. It is found that the air radiolysis products concentration increases with dose and tend to approach saturation levels at doses higher than about 1 kGy. This behaviour is more evident in oxygen/steam atmospheres, producing ozone, than in air/30% (v/v) steam atmospheres, the latter favouring the model-predicted on-going production of nitrogen dioxide even at very high doses. No significant effect of temperature, dose rate and hydrogen addition (4%, v/v) was observed. Furthermore, the inserted surfaces do not exhibit significant effects on the air radiolysis concentrations. However, these 'non-noticeable influence' could be due to a masking of small effects by the appreciable scattering of the experimental air radiolysis product concentrations. The PARIS results are then analysed using two

PARIS project: Radiolytic oxidation of molecular iodine in containment during a nuclear reactor severe accident

International Nuclear Information System (INIS)

Bosland, L.; Funke, F.; Girault, N.; Langrock, G.

2008-01-01

In case of a hypothetical severe accident in a nuclear LWR (light water reactor), the high radiation fields reached in the reactor containment building due to the release of fission products from the reactor core could induce air radiolysis. The air radiolysis products could, in turn, oxidise gaseous molecular iodine into aerosol-borne iodine-oxygen-nitrogen compounds. Thereby, this reaction involves a change of iodine speciation and a decrease of iodine volatility in the reactor containment atmosphere. Kinetic data were produced within the PARIS project on the air radiolysis products formation and destruction, and on their reaction with molecular iodine, with the objective of developing and validating existing kinetic models. The current paper includes the non-iodine tests of the PARIS project whose objective was to determine the rates of formation and destruction of air radiolysis products in the presence of both structural containment surfaces (decontamination coating ('paint') and stainless steel), aerosol particles such as silver rich particles (issued from the control rods) in boundary conditions representative for LWR or PHEBUS facility containments. It is found that the air radiolysis products concentration increases with dose and tend to approach saturation levels at doses higher than about 1 kGy. This behaviour is more evident in oxygen/steam atmospheres, producing ozone, than in air/30% (v/v) steam atmospheres, the latter favouring the model-predicted on-going production of nitrogen dioxide even at very high doses. No significant effect of temperature, dose rate and hydrogen addition (4%, v/v) was observed. Furthermore, the inserted surfaces do not exhibit significant effects on the air radiolysis concentrations. However, these 'non-noticeable influence' could be due to a masking of small effects by the appreciable scattering of the experimental air radiolysis product concentrations. The PARIS results are then analysed using two different kinetic models

The Ongkharak Nuclear Research Center (ONRC) research reactor project: a status review

International Nuclear Information System (INIS)

Rusch, R.; Jacobi, A. Jr.; Yamkate, P.

2001-01-01

The new Ongkharak Nuclear Research Center in the vicinity of Bangkok, Thailand is planned to replace the more than 30 years old facilities located in the Chatuchak district, Bangkok. An international team led by general atomics (GA) is designing and constructing the new research complex. It comprises a 10 MW TRIGA type reactor, an isotope production and a centralized waste processing and storage facility. Electrowatt-Ekono Ltd. was hired by the Thai Government Agency, the Office of Atomic Energy for Peace (OAEP), as a consultant to the project. As the project is now approaching the end of its 4 th year, it now stands at a decisive turning point. Basic design is nearly completed and detailed design is well advanced. The turnkey part of the contract including the reactor island, the isotope and waste facilities are still awaiting the issuance of the Construction Permit. Significant progress has been made on the other part of the project, which includes all the supporting infrastructure facilities. The Preliminary Safety Analysis Report (PSAR), prepared by GA, has been reviewed by various parties, including by nuclear safety experts from the IAEA, which has provided continuous support to the OAEP. Experts from the Argonne National Laboratory have been involved in the reviews as well. The PSAR is now under consideration at the Nuclear Facility Safety Sub-Committee (NFSS) of the Thai Atomic Energy for Peace Commission for issuing the Construction Permit of the ONRC Research Reactor. The following paper gives an overview of the project and its present status, outlining the features of the planned facilities and the issues the project is presently struggling with. Major lessons of the past 4 years are highlighted and an outlook into the future is attempted. (orig.)

Assessing and Projecting Greenhouse Gas Release due to Abrupt Permafrost Degradation

Science.gov (United States)

Saito, K.; Ohno, H.; Yokohata, T.; Iwahana, G.; Machiya, H.

2017-12-01

Permafrost is a large reservoir of frozen soil organic carbon (SOC; about half of all the terrestrial storage). Therefore, its degradation (i.e., thawing) under global warming may lead to a substantial amount of additional greenhouse gas (GHG) release. However, understanding of the processes, geographical distribution of such hazards, and implementation of the relevant processes in the advanced climate models are insufficient yet so that variations in permafrost remains one of the large source of uncertainty in climatic and biogeochemical assessment and projections. Thermokarst, induced by melting of ground ice in ice-rich permafrost, leads to dynamic surface subsidence up to 60 m, which further affects local and regional societies and eco-systems in the Arctic. It can also accelerate a large-scale warming process through a positive feedback between released GHGs (especially methane), atmospheric warming and permafrost degradation. This three-year research project (2-1605, Environment Research and Technology Development Fund of the Ministry of the Environment, Japan) aims to assess and project the impacts of GHG release through dynamic permafrost degradation through in-situ and remote (e.g., satellite and airborn) observations, lab analysis of sampled ice and soil cores, and numerical modeling, by demonstrating the vulnerability distribution and relative impacts between large-scale degradation and such dynamic degradation. Our preliminary laboratory analysis of ice and soil cores sampled in 2016 at the Alaskan and Siberian sites largely underlain by ice-rich permafrost, shows that, although gas volumes trapped in unit mass are more or less homogenous among sites both for ice and soil cores, large variations are found in the methane concentration in the trapped gases, ranging from a few ppm (similar to that of the atmosphere) to hundreds of thousands ppm We will also present our numerical approach to evaluate relative impacts of GHGs released through dynamic

Investigation of noble metal deposition behaviour in boiling water reactors. The NORA project

International Nuclear Information System (INIS)

Ritter, Stefan; Karastoyanov, Vasil; Abolhassani-Dadras, Sousan; Guenther-Leopold, Ines; Kivel, Niko

2010-01-01

NobleChem trademark is a technology developed by General Electric to reduce stress corrosion cracking (SCC) in reactor internals and recirculation pipes of boiling water reactors (BWRs) while preventing the negative side effects of classic hydrogen water chemistry. Noble metals (Pt, Rh) acting as electrocatalysts for the recombination of O 2 and H 2 O 2 with H 2 to H 2 O and thus reducing the corrosion potential more efficiently are injected into the feedwater during reactor shutdown (classic method) or on-line during power operation. They are claimed to deposit as very fine metallic particles on all water-wetted surfaces, including the most critical regions inside existing cracks, and to stay electrocatalytic over long periods of time. The effectiveness of this technology in plants still remains to be demonstrated. Based on highly credible laboratory experiments down to the sub-μg . kg -1 Pt concentration range, SCC mitigation may be expected, provided that a stoichiometric excess of H 2 and a sufficient surface coverage with very fine Pt particles exist simultaneously at the critical locations [1]. Very little is known about the deposition and (re-)distribution behaviour of the Pt in the reactor. For the validation of this technique the research project NORA (noble metal deposition behaviour in BWRs) has been started at the Paul Scherrer Institute (PSI) with two main objectives: (i) to gain phenomenological insights and a better basic understanding of the Pt distribution and deposition behaviour in BWRs; (ii) to develop and qualify a non-destructive technique to characterise the size and distribution of the Pt particles and the local concentration of Pt on reactor components. This paper presents the objectives of the project, the planned work and a brief description of the status of the project. (orig.)

Homogenous reactor, elaborations, not released up to end

International Nuclear Information System (INIS)

Takibayev, Zh.S.

2002-01-01

Nowadays the nuclear power uses mainly water moderated reactors, where water or heavy water works as neutron inhibitor or coolant, and fuel solid state is situated in reactor core discretely as fuel element packed in fuel assembly. Such fuel composition in solid state reactors leads to rise in price of reactor itself and, of course, many other inconveniences. Firstly, burning out depth is limited; secondary, agents absorbed neutrons are accumulated in fission products, i. e. it leads to poisoning slag derive and thirdly, there are too many outside agents in reactor core in the form of fuel elements and different constructional materials. It worsens neutron balance of reactor. There are many other inconveniences. Specialists understand this problem. They are looking for escaping of difficulty proposing to begin a wide-ranging design, for example, of a new generation of homogeneous reactor especially with salt liquid, liquid metal fuel. But this problem nowadays can not be nearly decided. It is clear enough that within at least 50-100 years the existing monopoly will not change its attitude to use of new elaboration, for example, reactor with salt liquid fuel unless a sharp necessity of opening up not only 1-2 % of uranium in the case of reactors on thermal neutrons or nearby 10-20 % for fast reactors as nowadays but effective use of all potential of nuclear fission energy contained in natural uranium and thorium resources will be realized. In the report the scheme of nuclear reactor with liquid metal or salt liquid is shown. Such approach can be in future one of possible variants of problem solution in effective opening up of all uranium-plutonium energy resource of our planet. The scheme shows only possible allocations of the container and the pipeline. Their proportioning is one of main problems of future elaborations. A mutual allocation of the container and pipelines was carried out in such way, that demand to the last ones where less than to the container

Effect of biogas sparging on the performance of bio-hydrogen reactor over a long-term operation

Science.gov (United States)

Nualsri, Chatchawin; Kongjan, Prawit; Imai, Tsuyoshi

2017-01-01

This study aimed to enhance hydrogen production from sugarcane syrup by biogas sparging. Two-stage continuous stirred tank reactor (CSTR) and upflow anaerobic sludge blanket (UASB) reactor were used to produce hydrogen and methane, respectively. Biogas produced from the UASB was used to sparge into the CSTR. Results indicated that sparging with biogas increased the hydrogen production rate (HPR) by 35% (from 17.1 to 23.1 L/L.d) resulted from a reduction in the hydrogen partial pressure. A fluctuation of HPR was observed during a long term monitoring because CO2 in the sparging gas and carbon source in the feedstock were consumed by Enterobacter sp. to produce succinic acid without hydrogen production. Mixed gas released from the CSTR after the sparging can be considered as bio-hythane (H2+CH4). In addition, a continuous sparging biogas into CSTR release a partial pressure in the headspace of the methane reactor. In consequent, the methane production rate is increased. PMID:28207755

Environmentally-assisted cracking in austenitic light water reactor structural materials. Final report of the KORA-I project

Energy Technology Data Exchange (ETDEWEB)

Seifert, H.-P.; Ritter, S

2009-03-15

The following document is the final report of the KORA-I project, which was performed at the Paul Scherrer Institute (PSI) between 2006 and 2008 and was funded by the Swiss Nuclear Safety Inspectorate (ENSI). The three sub-projects of KORA-I covered the experimental characterisation of the effect of the reactor coolant environment on fatigue initiation and crack growth in austenitic stainless steels under boiling and pressurised water reactor conditions, the experimental evaluation of the potential and limits of the electrochemical noise measurement technique for the early detection of stress corrosion cracking initiation in austenitic stainless steels under boiling water reactor/normal water chemistry conditions, as well as the characterisation of the stress corrosion crack growth behaviour in the fusion line region of an Alloy 182-low-alloy reactor pressure vessel steel dissimilar metal weld. The main scientific results and major conclusions of the three sub-projects are discussed in three independent parts of this report. (author)

Environmentally-assisted cracking in austenitic light water reactor structural materials. Final report of the KORA-I project

International Nuclear Information System (INIS)

Seifert, H.-P.; Ritter, S.

2009-03-01

The following document is the final report of the KORA-I project, which was performed at the Paul Scherrer Institute (PSI) between 2006 and 2008 and was funded by the Swiss Nuclear Safety Inspectorate (ENSI). The three sub-projects of KORA-I covered the experimental characterisation of the effect of the reactor coolant environment on fatigue initiation and crack growth in austenitic stainless steels under boiling and pressurised water reactor conditions, the experimental evaluation of the potential and limits of the electrochemical noise measurement technique for the early detection of stress corrosion cracking initiation in austenitic stainless steels under boiling water reactor/normal water chemistry conditions, as well as the characterisation of the stress corrosion crack growth behaviour in the fusion line region of an Alloy 182-low-alloy reactor pressure vessel steel dissimilar metal weld. The main scientific results and major conclusions of the three sub-projects are discussed in three independent parts of this report. (author)

Modelling the release behaviour of cesium during severe fuel degradation

International Nuclear Information System (INIS)

Lewis, B.J.; Andre, B.; Morel, B.

1995-01-01

An analytical model has been applied to describe the diffusional release of fission product cesium from Zircaloy-clad fuel under high-temperature reactor accident conditions. The present treatment accounts for the influence of the atmosphere (i.e., changing oxygen potential) on the state of fuel oxidation and the release kinetics. The effects of fuel dissolution on the volatile release behaviour (under reducing conditions) is considered in terms of earlier crucible experiments and a simple model based on bubble coalescence and transport in metal pools. The model has been used to interpret the cesium release kinetics observed in steam and hydrogen experiments at the Vertical Irradiation (VI) Facility in the Oak Ridge National Laboratory and at the HEVA/VERCORS Facility in the Commissariat a l'Energie Atomique. (author)

Development of the reactor antineutrino detection technology within the iDream project

Science.gov (United States)

Gromov, M.; Kuznetsov, D.; Murchenko, A.; Novikova, G.; Obinyakov, B.; Oralbaev, A.; Plakitina, K.; Skorokhvatov, M.; Sukhotin, S.; Chepurnov, A.; Etenko, A.

2017-12-01

The iDREAM (industrial Detector for reactor antineutrino monitoring) project is aimed at remote monitoring of the operating modes of the atomic reactor on nuclear power plant to ensure a technical support of IAEA non-proliferation safeguards. The detector is a scintillator spectrometer. The sensitive volume (target) is filled with a liquid organic scintillator based on linear alkylbenzene where reactor antineutrinos will be detected via inverse beta-decay reaction. We present first results of laboratory tests after physical launch. The detector was deployed at sea level without background shielding. The number of calibrations with radioactive sources was conducted. All data were obtained by means of a slow control system which was put into operation.

Plutonium and minor actinides management in thermal high - temperature reactors - the EU FP6 project puma

International Nuclear Information System (INIS)

Kuijper, J. C.

2007-01-01

The High Temperature gas-cooled Reactor (HTR) can fulfil a very useful niche for the purposes of Pu and Minor Actinide (MA) incineration due to its unique and unsurpassed safety features, as well as to the attractive incentives offered by the nature of the coated particle (CP) fuel. No European reactor of this type is currently available, but there has been, and still is, considerable interest internationally. Decisions to construct such a reactor in China and in South Africa have already been made or are about to be made. Apart from the unique and unsurpassed safety features offered by this reactor type, the nature of the CP fuel offers a number of attractive characteristics. In particular, it can withstand burn-ups far beyond that in either LWR or FR systems. Demonstrations as high as 75% FIMA have been achieved. The coated particle itself offers significantly improved proliferation resistance, and finally with a correct choice of the kernel composition, it can be a very effective support for direct geological disposal of the fuel. The overall objective of the PUMA project, a Specific Targeted Research Project (STREP) within the European Union 6th Framework (EU FP6), is to investigate the possibilities for the utilisation and transmutation of plutonium and especially minor actinides in contemporary and future (high temperature) gas-cooled reactor designs, which are promising tools for improving the sustainability of the nuclear fuel cycle. This contributes to the reduction of Pu and MA stockpiles, and also to the development of safe and sustainable reactors for CO 2 -free energy generation. A number of important issues concerning the use of Pu and MA in gas-cooled reactors have already been dealt with in other projects, or are being treated in ongoing projects, e.g. as part of EU FP6. However, further steps are required to demonstrate the potential of HTRs as Pu/MA transmuters based on realistic/feasible designs of CP Pu/MA fuel and the PUMA focuses on necessary

Pressure loadings of Soviet-designed VVER [Water-Cooled, Water-Moderated Energy Reactor] reactor release mitigation structures from large-break LOCAs

International Nuclear Information System (INIS)

Sienicki, J.J.; Horak, W.C.

1989-01-01

Analyses have been carried out of the pressurization of the accident release mitigation structures of Soviet-designed VVER (Water-Cooled, Water-Moderated Energy Reactor) pressurized water reactors following large-break loss-of-coolant accidents. Specific VVER systems for which calculations were performed are the VVER-440 model V230, VVER-440 model V213, and VVER-1000 model V320. Descriptions of the designs of these and other VVER models are contained in the report DOE/NE-0084. The principal objective of the current analyses is to calculate the time dependent pressure loadings inside the accident localization or containment structures immediately following the double-ended guillotine rupture of a primary coolant pipe. In addition, the pressures are compared with the results of calculations of the response of the structures to overpressure. Primary coolant system thermal hydraulic conditions and the fluid conditions at the break location were calculated with the RETRAN-02 Mod2 computer code (Agee, 1984). Pressures and temperatures inside the building accident release mitigation structures were obtained from the PACER (Pressurization Accompanying Coolant Escape from Ruptures) multicompartment containment analysis code developed at Argonne National Laboratory. The analyses were carried out using best estimate models and conditions rather than conservative, bounding-type assumptions. In particular, condensation upon structure and equipment was calculated using correlations based upon analyses of the HDR, Marviken, and Battelle Frankfurt containment loading experiments. The intercompartment flow rates incorporate an effective discharge coefficient and liquid droplet carryover fraction given by expressions of Schwan determined from analyses of the Battelle Frankfurt and Marviken tests. 5 refs., 4 figs

Estimation of the environmental or radiological impact in the event of accidental release of radionuclides in a DCLL fusion reactor; Estimacion del impacto radiologico ambiental en caso de liberacion accidental de radionucleidos en un reactor de fusion DCLL

Energy Technology Data Exchange (ETDEWEB)

Palermo, I.; Gomez Ros, J. M.; Sanz, J.; Mota, F.

2013-07-01

Tritium production and activation in the LiPb products can pose a radiological risk in the event of accidental release in a fusion reactor. Within the research programme Consolider TECNO{sub F}US (CSD2008-079) fusion technology has developed a design for a reactor with regenerative wrap with dual refrigeration (DCLL). The purpose of this communication is to present estimates of the radiological impact derived from an accidental release of radionuclides from the circuit of LiPb provinients. (Author)

Severe accident assessment. Results of the reactor safety research project VAHTI

International Nuclear Information System (INIS)

Sairanen, R.

1997-10-01

The report provides a summary of the publicly funded nuclear reactor safety research project Severe Accident Management (VAHTI). The project has been conducted at the Technical Research Centre of Finland (VTT) during the years 1994-96. The main objective was to assist the severe accident management programmes of the Finnish nuclear power plants. The project was divided into five work packages: (1) thermal hydraulic validation of the APROS code, (2) core melt progression within a BWR pressure vessel, (3) failure mode of the BWR pressure vessel, (4) Aerosol behaviour experiments, and (5) development of a computerized severe accident training tool

Monitoring nuclear reactors with anti-neutrino detectors: the ANGRA project

Energy Technology Data Exchange (ETDEWEB)

Chimenti, Pietro; Leigui, Marcelo Augusto [UFABC - Universidade Federal do ABC. Rua Santa Adelia, 166. Bairro Bangu. Santo Andre - SP (Brazil); Anjos, Joao; Azzi, Gabriel; Rafael, Gama; Ademarlaudo, Barbosa; Lima, Herman; VAZ, Mario; Villar, Arthur [Centro Brasileiro de Pesquisas Fisicas - CBPF, Rua Dr. Xavier Sigaud, 150, Urca, Rio de Janeiro, RJ - 22290-180 (Brazil); Gonzales, Luis Fernando; Bezerra, Thiago; Kemp, Ernesto [Unicamp, State University of Campinas, Cidade Universitaria ' Zeferino Vaz' , Barao Geraldo - Campinas, Sao Paulo (Brazil); Nunokawa, Hiroshi [Department of Physics, Pontifical Catholic University - PUC, Rua Marques de Sao Vicente, 225, 22451-900 Gavea - Rio de Janeiro - RJ (Brazil); Guedes, Germano; Faria, Paulo Cesar [Universidade Estadual de Feira de Santana - UEFS, Avenida Transnordestina, Novo Horizonte (Brazil); Pepe, Iuri [Universidade Federal da Bahia - UFBA (Brazil)

2010-07-01

We describe the status of the ANGRA Project, aimed at developing an anti-neutrino detector for monitoring nuclear reactors. Indeed the detection of anti-neutrinos provides a unique handle for non-invasive measurements of the nuclear fuel. This kind of measurements are of deep interest for developing new safeguards tools which may help in nuclear non-proliferation programs. The ANGRA experiment, placed at about 30 m from the core of the 4 GW Brazilian nuclear power reactor ANGRA II, is based on a water Cherenkov detector with about one ton target mass. A few thousand antineutrino interactions per day are expected. The latest results from simulations and the status of the construction are presented. (authors)

Hydrogen Release From 800-MeV Proton-Irradiated Tungsten

International Nuclear Information System (INIS)

Oliver, Brian M.; Venhaus, Thomas J.; Causey, Rion A.; Garner, Francis A.; Maloy, Stuart A.

2002-01-01

Tungsten irradiated in spallation neutron sources such as those proposed for the Accelerator Production of Tritium (APT) project, or in proposed fusion reactors, will contain large quantities of generated helium and hydrogen gas. In the APT, spallation neutrons would be generated by the interaction of high energy (∼1 GeV) protons with solid tungsten rods or cylinders. In fusion reactors, tungsten used in a tokamak diverter will contain hydrogen, as well as deuterium and tritium diffusing in from the plasma-facing surface. The release kinetics of these gases during various off-normal scenarios involving loss of coolant and afterheat-induced rises in temperature is of particular interest for both applications. To determine the release kinetics of hydrogen from tungsten, tungsten rods irradiated with 800 MeV protons in the Los Alamos Neutron Science Center (LANCE) to high exposures as part of the APT project have been examined. Hydrogen evolution from the tungsten was measured using a dedicated mass spectrometer system by subjecting the specimens to an essentially linear temperature ramp from ∼323 K to ∼1473 K. Release profiles are compared with predictions obtained using the Tritium Migration Analysis Program (TMAP4). Input parameters for the modeling, consisting of diffusivity, recombination rate coefficient, and trapping, are discussed. The measurements show that for high proton doses, the majority of the hydrogen is released gradually, starting at about 900 K and reaching a maximum at about 1400 K, where it drops fairly rapidly. Comparisons with TMAP show reasonable agreement at high proton dose using a trap value of 1.4 eV and a trap density of 3%. There is also a small release fraction occurring at ∼600 K which predominates at lower proton doses, and which is relatively independent of dose. This lower-temperature release is predicted by TMAP if no traps are assumed, suggesting that this release may represent an adsorbed surface component

Releasing method of connection of control rod and its drive mechanism in a reactor

International Nuclear Information System (INIS)

Ishida, Kazuo; Futatsugi, Masao.

1976-01-01

Object: To disengage a control rod from a control rod drive device in a boiling water reactor with a minimal failure of the device, when connection there between cannot be released in a normal manner. Structure: First, a part of a piston tube in the control rod drive device is withdrawn externally of a control rod housing and cut. Next, a discharge tool, which is designed to be connected with the cut piston tube, is connected to the remainder of the piston tube within the housing and the aforesaid piston tube is pushed into the index tube. The index tube is then cut by the discharge tool. Thus, the control rod drive device and the control rod may be separated. Thereafter, the control rod may be removed from the top of the reactor container whereas the control rod drive device removed from the bottom thereof. (Ikeda, J.)

Introduction [International Reactor Dosimetry File 2002 (IRDF-2002)

International Nuclear Information System (INIS)

Paviotti-Corcuera, R.; Zolnay, E.M.

2006-01-01

The most recently tested version of the International Reactor Dosimetry File, IRDF-90 Version 2 (IRDF-90.2), was released in 1993. Most of the evaluations used in this file were prepared in the mid-1980s, and in the meantime a large amount of new experimental data has become available, along with two new national reactor dosimetry libraries (the Russian Reactor Dosimetry File (RRDF-98) and the Japanese Evaluated Nuclear Data Library (JENDL/D-99)). The cross-sections and related uncertainties for several reactions in these libraries may be of better quality than the data in the older IRDF-90 file. These developments have resulted in different cross-section values being applied to the evaluation of experimental data, creating difficulties in comparing the results of reactor dosimetry calculations from the same types of nuclear facility. Therefore, there has been a strong demand from the reactor dosimetry community for an updated and standardized version of the IRDF. The IAEA has in the past supported similar efforts to improve the quality of data for reactor dosimetry applications. A major objective of the present data development project was to prepare and distribute a standardized, updated and tested reactor dosimetry cross-section library accompanied by uncertainty information (IRDF-2002) for use in service life assessments of nuclear power reactors. In order to achieve this objective, two technical meetings were organized. Both meetings were held at the IAEA in Vienna. The first meeting took place from 27 to 29 August 2002, the second from 1 to 3 October 2003. Recommendations were made concerning the following topics and the preparation of the library: reactions to be included, requirements for new evaluations or revisions, nuclear decay data, radiation damage data, testing of the data in benchmark fields and inclusion of computer codes. The participants emphasized that good quality nuclear data for reactor dosimetry are essential to improve assessments of the

Description of the quality system and the organisation of activities at the Halden Reactor Project

International Nuclear Information System (INIS)

Tiseth, Ann Katrine

1996-04-01

The Halden Reactor Project is a joint undertaking of national organisations in 19 countries sponsoring a jointly financed programme under the auspices of the OECD - Nuclear Energy Agency. The quality assurance routines in force at the Halden Reactor Project are based on long term experience and are devised to ensure product quality and meeting of programme goals, customers expectations and authority requirements. Quality is an overall connotation related to all activities carried out at the Project and concerns all individuals performing such activities. It is also related to subcontractors and suppliers of parts and components. The results of the work depend very strongly on the quality level of each component, regardless how small it is. The activities at the Halden Reactor Project are organised in eight technical divisions, one advisory group and one administrative group. This report describes the quality system, the organisation of the activities in the divisions and the technical and administrative infrastructures. The quality system is built according to the international standards ISO 9001 and ISO 9000-3. Iso 9000-3 is ISO 9001 applied to software development, supply and maintenance. (author)

Growth and Expansion of the International Criticality Safety Benchmark Evaluation Project and the Newly Organized International Reactor Physics Experiment Evaluation Project

International Nuclear Information System (INIS)

J. Blair Briggs; Lori Scott; Yolanda Rugama; Enrico Satori

2007-01-01

Since ICNC 2003, the International Criticality Safety Benchmark Evaluation Project (ICSBEP) has continued to expand its efforts and broaden its scope. Criticality-alarm/shielding type benchmarks and fundamental physics measurements that are relevant to criticality safety applications are not only included in the scope of the project, but benchmark data are also included in the latest version of the handbook. A considerable number of improvements have been made to the searchable database, DICE and the criticality-alarm/shielding benchmarks and fundamental physics measurements have been included in the database. There were 12 countries participating on the ICSBEP in 2003. That number has increased to 18 with recent contributions of data and/or resources from Brazil, Czech Republic, Poland, India, Canada, and China. South Africa, Germany, Argentina, and Australia have been invited to participate. Since ICNC 2003, the contents of the ''International Handbook of Evaluated Criticality Safety Benchmark Experiments'' have increased from 350 evaluations (28,000 pages) containing benchmark specifications for 3070 critical or subcritical configurations to 442 evaluations (over 38,000 pages) containing benchmark specifications for 3957 critical or subcritical configurations, 23 criticality-alarm-placement/shielding configurations with multiple dose points for each, and 20 configurations that have been categorized as fundamental physics measurements that are relevant to criticality safety applications in the 2006 Edition of the ICSBEP Handbook. Approximately 30 new evaluations and 250 additional configurations are expected to be added to the 2007 Edition of the Handbook. Since ICNC 2003, a reactor physics counterpart to the ICSBEP, The International Reactor Physics Experiment Evaluation Project (IRPhEP) was initiated. Beginning in 1999, the IRPhEP was conducted as a pilot activity by the by the Organization of Economic Cooperation and Development (OECD) Nuclear Energy Agency

Evaluation of PAHs in groundwater and surface waters at Multipurpose Reactor Installation Area

International Nuclear Information System (INIS)

Pereira, Karoline P.; Martins, Elâine A.J.; Cotrim, Marycel E.B.; Pires, Maria A.F.

2017-01-01

Brazil has four research reactors in operation, all old and low power. The IEA-R1 reactor of IPEN/CNEN-SP has only limited radioisotope production capacity, materials irradiation, and neutron beam utilization. This reactor has been operating for fifty-nine years and has prospects of operation for a maximum period of ten years. It is necessary to implement a new reactor, which will support nuclear activities, and the national strategic objectives related to technological development in the areas of energy and defense; scientific and technological development; training of human resources and the growing production of radioisotopes for medical application. The Brazilian Multipurpose Reactor (RMB) will be a nuclear reactor for research and will be built in the state of São Paulo, in the municipality of Iperó. Its construction may involve the release of effluents into the environment. With monitoring before, during and after construction, it will be possible to verify if the construction itself will harm the environment. Several organics compounds are released daily in water bodies collaborating for environmental imbalance. Many of them have carcinogenic and mutagenic properties, receiving more attention by the scientific community. Most of the organic compounds are not included in environmental legislation and many of them present high toxicity, especially those classified as endocrine disrupters, as some Polycyclic Aromatic Hydrocarbons (PAHs). Only seven of the thirteen PAHs studied in this project are contemplated in Brazilian legislation, and just one is contained in international legislation. The PAHs studied in this work present, considered hazardous chemical compounds due to their toxicity, persistence in the environment, their bioaccumulative potential and their tendency to biomagnify. For the determination of the PAHs, the samples were concentrated by solid phase extraction (SPE) followed by quantification by High Performance Liquid Chromatography (HPLC). It

Evaluation of PAHs in groundwater and surface waters at Multipurpose Reactor Installation Area

Energy Technology Data Exchange (ETDEWEB)

Pereira, Karoline P.; Martins, Elâine A.J.; Cotrim, Marycel E.B.; Pires, Maria A.F., E-mail: karolinedepaulapereira@usp.br, E-mail: elaine@ipen.br, E-mail: mecotrim@ipen.br, E-mail: mapires@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

2017-07-01

Brazil has four research reactors in operation, all old and low power. The IEA-R1 reactor of IPEN/CNEN-SP has only limited radioisotope production capacity, materials irradiation, and neutron beam utilization. This reactor has been operating for fifty-nine years and has prospects of operation for a maximum period of ten years. It is necessary to implement a new reactor, which will support nuclear activities, and the national strategic objectives related to technological development in the areas of energy and defense; scientific and technological development; training of human resources and the growing production of radioisotopes for medical application. The Brazilian Multipurpose Reactor (RMB) will be a nuclear reactor for research and will be built in the state of São Paulo, in the municipality of Iperó. Its construction may involve the release of effluents into the environment. With monitoring before, during and after construction, it will be possible to verify if the construction itself will harm the environment. Several organics compounds are released daily in water bodies collaborating for environmental imbalance. Many of them have carcinogenic and mutagenic properties, receiving more attention by the scientific community. Most of the organic compounds are not included in environmental legislation and many of them present high toxicity, especially those classified as endocrine disrupters, as some Polycyclic Aromatic Hydrocarbons (PAHs). Only seven of the thirteen PAHs studied in this project are contemplated in Brazilian legislation, and just one is contained in international legislation. The PAHs studied in this work present, considered hazardous chemical compounds due to their toxicity, persistence in the environment, their bioaccumulative potential and their tendency to biomagnify. For the determination of the PAHs, the samples were concentrated by solid phase extraction (SPE) followed by quantification by High Performance Liquid Chromatography (HPLC). It

IAEA Assistance in the development of new research reactor projects

Energy Technology Data Exchange (ETDEWEB)

Borio di Tigliole, Andrea; Bradley, Ed; Zhukova, Anastasia; Adelfang, Pablo [International Atomic Energy Agency, Research Reactor Section, Vienna (Austria); Shokr, Amgad [International Atomic Energy Agency, Research Reactor Safety Section, Vienna (Austria); Ridikas, Danas [International Atomic Energy Agency, Physics Section, Vienna (Austria)

2015-08-15

A research reactor (RR) project is a major undertaking that requires careful preparation, planning, implementation and investment in time, money, and human resources. In recent years, the interest of IAEA Member States in developing RR programmes has grown significantly, and currently, several Member States are in different stages of new RR projects. The majority of these countries are building their first RR as a key national facility for the development of their nuclear science and technology programmes, including nuclear power. In order to support Member States in such efforts, the IAEA in 2012 published the Nuclear Energy Series Report No. NP-T-5.1 on Specific Considerations and Milestones for a Research Reactor Project. To provide further support, the IAEA also published a document to assist Member States in the preparation of the bid invitation specification for the purchase of a RR. The IAEA will also continue to provide assistance for human resources development of the Member States establishing their first RR, and to facilitate sharing experience and knowledge among Member States through its programmatic activities including expert mission services, technical meetings, training courses and workshops addressing relevant technical and safety topics. This paper presents the IAEA assistance and services provided to the Member States considering new RRs, with particular emphasis on those establishing their first RR, including elaboration on the services mentioned above.

Spanish contribution in the design of the Alfred Reactor inside the ESNII+ Project

Energy Technology Data Exchange (ETDEWEB)

Romojaro, P.; García-Herranz, N.; Álvarez-Velarde, F.; López, D.

2015-07-01

Significant efforts are being devoted in order to boost R&D on advanced nuclear reactors due to their sustainability and improved safety characteristics. The main drawbacks for the industrial deployment of a Lead-cooled Fast Reactor (LFR) are the lack of operational experience and the technological uncertainties. In order to measure the robustness of the design and improve the safety characteristics of the ALFRED reactor -the demonstration reactor of the European LFR technology- a detailed analysis is envisaged within the EU FP7 ESNII+ project (project to support the European Sustainable Industrial Initiative) (ESNII+, 2013). One key research goal for ALFRED is the demonstration of favourable transient behaviour under accident conditions. Such behaviour depends primarily on the reactivity coefficients of the core. For evaluation of those coefficients, computational tools capable of providing results with a high level of accuracy are available. But the results will be affected by different sources of uncertainty, such as uncertainties on the engineering design, on the nuclear data, model uncertainties, etc. The objective of this work is to perform a sensitivity/uncertainty analysis of ALFRED reactor to assess the impact on the core reactivity of the uncertainties in nuclear data as well as the uncertainties in geometrical tolerances. This will allow having an exhaustive picture of their influence on the core performance, identifying key parameters and proposing specific R&D actions to achieve an improved safety level. (Author)

The design, safety and project development status of the modular high temperature gas-cooled reactor in the United States

International Nuclear Information System (INIS)

Mears, L.D.; Dean, R.A.

1987-01-01

The cooperative government and industry Modular High Temperature Gas-Cooled Reactor (MHTGR) Program in the United States has advanced a 350 MW(t) plant design through the conceptual development stage. The system incorporates an annular core of prismatic fuel elements within a steel pressure vessel connected, in a side-by-side arrangement, by a concentric duct to a second steel vessel containing a steam generator and helium coolant circulator. The reference plant design consists of four reactor modules installed in separate below-grade silos, providing steam to two conventional turbine generators. The nominal net plant output is 540 MW(e). The small reactor system takes unique advantage of the high temperature capability of the refractory coated fuel and the large thermal inertia of the graphite moderator to provide a design capable of withstanding a complete loss of active core cooling without causing excessive core heatup and significant release of fission products from the fuel. Present program activities are concentrated on interactions with the Nuclear Regulatory Commission aimed at obtaining a Licensability Statement. A project initiative to build a prototype plant which would demonstrate the MHTGR-unique licensing process, plant performance, costs and schedule plus establish an industrial infrastructure to proceed with follow-on commercial MHTGR plants by the turn of the century, is being undertaken by the utility/vendor participants (author)

An overview of the fuels and materials testing programme at the OECD Halden Reactor Project

Energy Technology Data Exchange (ETDEWEB)

Wiesenack, W [Institutt for Energiteknikk, Halden (Norway). OECD Halden Reaktor Projekt

1997-08-01

The fuels and materials testing programme of the OECD Halden Reactor Project is aimed at investigations of fuel and cladding properties at high burnup, water chemistry effects and in-core materials ageing problems. For the execution of this programme, different types of irradiation rigs and experimental facilities providing typical power reactors conditions are available. Data are obtained from in-core sensors developed at the Halden Project; these are shortly described. An overview of the current test programme and the scope of the following years are briefly presented. (author). 5 refs, 3 figs.

The IAEA's international project on innovative nuclear reactors and fuel cycles (INPRO)

International Nuclear Information System (INIS)

Kuptiz, Juergen; )

2002-01-01

This paper presents the IAEA International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO). It defines its rationale, key objectives and specifies the organizational structure. The IAEA General Conference (2000) has invited all interested Member states to combine their efforts under the aegis of the Agency in considering the issues of the nuclear fuel cycle, in particular by examining innovative and proliferation-resistant nuclear technology and invited Member states to consider to contribute to a task force on innovative nuclear reactors and fuel cycle

Surface radiological free release program for the Battelle Columbus Laboratory Decommissioning Project

International Nuclear Information System (INIS)

Horton, C.N.

1995-01-01

This paper was prepared for the Second Residual Radioactivity and Recycling Criteria Workshop and discusses decommissioning and decontamination activities at the Battelle Columbus Laboratories Decommissioning Project (BCLDP). The BCLDP is a joint effort between the Department of Energy (DOE) and Battelle Columbus Operations to decontaminate fifteen Battelle-owned buildings contaminated with DOE radioactive materials. The privately owned buildings located across the street from The Ohio State University campus became contaminated with natural uranium and thorium during nuclear research activities. BCLDP waste management is supported by an extensive radiological free-release program. Miscellaneous materials and building surfaces have been free-released from the BCLDP. The free-release program has substantially reduced radioactive waste volumes and supported waste minimization. Free release for unrestricted use has challenged regulators and NRC licensees since the development of early surface-release criteria. This paper discusses the surface radiological free-release program incorporated by the BCLDP and the historical development of the surface radiological free-release criteria. Concerns regarding radiological free-release criteria are also presented. (author)

Tritium recapture behavior at a nuclear power reactor due to airborne releases.

Science.gov (United States)

Harris, Jason T; Miller, David W; Foster, Doug W

2008-08-01

This paper describes the initiatives taken by Cook Nuclear Plant to study the on-site behavior of recaptured tritium released in its airborne effluents. Recapture is the process where a released radioactive effluent, in this case tritium, is brought back on-site through some mechanism. Precipitation, shifts in wind direction, or anthropogenic structures that restrict or alter effluent movement can all lead to recapture. The investigation was started after tritium was detected in the north storm drain outfall. Recent inadvertent tritium releases by several other nuclear power plants, many of which entered the groundwater, have led to increased surveillance and scrutiny by regulatory authorities and the general public. To determine the source of tritium in the outfall, an on-site surface water, well water, rainwater and air-conditioning condensate monitoring program was begun. Washout coefficients were also determined to compare with results reported by other nuclear power plants. Program monitoring revealed detectable tritium concentrations in several precipitation sample locations downwind of the two monitored containment building release vents. Tritium was found in higher concentrations in air-conditioning condensate, with a mean value of 528 Bq L(-1) (14,300 pCi L(-1)). The condensate, and to a lesser extent rainwater, were contributing to the tritium found in the north storm drain outfall. Maximum concentration values for each sample type were used to estimate the most conservative dose. A maximum dose of 1.1 x 10(-10) mSv (1.1 x 10(-8) mrem) total body was calculated to determine the health impact of the tritium detected.

Measurement and characterization of fission products released from LWR fuel

International Nuclear Information System (INIS)

Osborne, M.F.; Collins, J.L.; Lorenz, R.A.; Norwood, K.S.; Strain, R.V.

1984-01-01

Samples of commercial LWR fuel have been heated under simulated accident conditions to determine the extent and the chemical forms of fission product release. This project was sponsored by the USNRC under a broad program of reactor safety studies. Of the five tests discussed, the fractional releases of Kr, I, and Cs varied from approx. 2% at 1400 0 C to >50% at 2000 0 C; much smaller fractions of Ru, Ag, Sb, and Te were measured in some tests. The major chemical forms in the effluent appeared to include CsI, CsOH, Sb, Te, and Ag

A Mechanistic Source Term Calculation for a Metal Fuel Sodium Fast Reactor

Energy Technology Data Exchange (ETDEWEB)

Grabaskas, David; Bucknor, Matthew; Jerden, James

2017-06-26

A mechanistic source term (MST) calculation attempts to realistically assess the transport and release of radionuclides from a reactor system to the environment during a specific accident sequence. The U.S. Nuclear Regulatory Commission (NRC) has repeatedly stated its expectation that advanced reactor vendors will utilize an MST during the U.S. reactor licensing process. As part of a project to examine possible impediments to sodium fast reactor (SFR) licensing in the U.S., an analysis was conducted regarding the current capabilities to perform an MST for a metal fuel SFR. The purpose of the project was to identify and prioritize any gaps in current computational tools, and the associated database, for the accurate assessment of an MST. The results of the study demonstrate that an SFR MST is possible with current tools and data, but several gaps exist that may lead to possibly unacceptable levels of uncertainty, depending on the goals of the MST analysis.

Application of CFD Codes in Nuclear Reactor Safety Analysis

Directory of Open Access Journals (Sweden)

T. Höhne

2010-01-01

Full Text Available Computational Fluid Dynamics (CFD is increasingly being used in nuclear reactor safety (NRS analyses as a tool that enables safety relevant phenomena occurring in the reactor coolant system to be described in more detail. Numerical investigations on single phase coolant mixing in Pressurised Water Reactors (PWR have been performed at the FZD for almost a decade. The work is aimed at describing the mixing phenomena relevant for both safety analysis, particularly in steam line break and boron dilution scenarios, and mixing phenomena of interest for economical operation and the structural integrity. For the experimental investigation of horizontal two phase flows, different non pressurized channels and the TOPFLOW Hot Leg model in a pressure chamber was build and simulated with ANSYS CFX. In a common project between the University of Applied Sciences Zittau/Görlitz and FZD the behaviour of insulation material released by a LOCA released into the containment and might compromise the long term emergency cooling systems is investigated. Moreover, the actual capability of CFD is shown to contribute to fuel rod bundle design with a good CHF performance.

Audit of United States portion of the International Thermonuclear Experimental Reactor project

International Nuclear Information System (INIS)

1993-01-01

Worldwide efforts in fusion energy research are designed to develop fusion power as a safe, environmentally sound, and economically competitive source of energy. The International Thermonuclear Experimental Reactor (ITER) project is a worldwide effort to demonstrate the scientific and technological feasibility of fusion power. The European Community, Japan, the Russian Federation, and the United States are collaborating on ITER, with each of the four parties expected to equally share costs and benefits. Shared costs for the current engineering design phase of the project are estimated at $1 billion in 1989 dollars, excluding certain management and support costs to be absorbed by each partner, with an early estimate of $6 billion, also in 1989 dollars, for construction of the reactor. Engineering design formally began in July 1992, and this phase is in its formative stages. The US had already spent about $100 million since 1987 on ITER conceptual design activities and other preparatory activities in advance of the engineering design phase. Because of its cost significance, the importance of ITER to the US fusion energy program, and the project's unique aspects which may provide a framework for future international endeavors, we initiated an audit of the ITER project. The purpose of the audit was to evaluate management controls over the US portion of the ITER project. Our objectives was to determine whether key front-end controls were in place to ensure that the project could be managed in an efficient and effective manner

The International Science and Technology Center (ISTC) and ISTC projects related to research reactors: information review

Energy Technology Data Exchange (ETDEWEB)

Tocheniy, L. V.; Rudneva, V. Ya. [ISTC, Moscow (Russian Federation)

1998-07-01

The ISTC is an intergovernmental organization established by agreement between the Russian Federation, the European Union, Japan, and the United States. Since 1994, Finland, Sweden, Norway, Georgia, Belarus, Kazakhstan and the Kyrgyz Republic have acceded to the Agreement and Statute. At present, the Republic of Korea is finishing the process of accession to the ISTC. All work of the ISTC is aimed at the goals defined in the ISTC Agreement: To give CIS weapons scientists, particularly those who possess knowledge and skills related to weapons of mass destruction and their delivery systems, the opportunities to redirect their talents to peaceful activities; To contribute to solving national and international technical problems; To support the transition to market-based economics; To support basic and applied research; To help integrate CIS weapons scientists into the international scientific community. The projects may be funded both through governmental funds of the Funding partners of the ISTC. According to the ISTC Statute, approved by the appropriate national organizations, funds used within ISTC projects are exempt from CIS taxes. As of March 1998, more than 1500 proposals had been submitted to the Center, of which 551 were approved for funding, for a total value of approximately US$166 million. The number of scientists and engineers participating in the projects is more than 18000. There are about 20 funded and as yet nonfunded projects related to various problems of research reactors. Many of them address safety issues. Information review of the results and plans of both ongoing projects and as yet nonfunded proposals related to research reactors will be presented with the aim assisting international researchers to establish partnerships or collaboration with ISTC projects. The following groups of ISTC projects will be represented: 1. complex computer simulator s for research reactors; 2. reactor facility decommissioning; 3. neutron sources for medicine; 4

Decommissioning techniques for research reactors. Final report of a co-ordinated research project 1997-2001

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

in this technical publication. Operating experience in real-scale applications, lessons learned, key results in laboratory scale or pilot scale research, and validation of mathematical models, are among the most significant achievements of the CRP and have been highlighted. The objective of this CRP was to promote the exchange of information on the practical experience gained by Member States in decommissioning or operation, maintenance, and refurbishment activities which would be eventually related to the decommissioning of research reactors. Special emphasis was given to the development/adaptation of methods and approaches for optimization of the decommissioning process. The scope of the project included several technical areas of decommissioning rather than focusing on a single aspect of it. It was felt that this format would generate more awareness of the integrated approach to decommissioning. In particular, the scope included the following: design, construction and operational features to assist in final decommissioning; planning for decommissioning, including technical solution assessment; decommissioning strategies and their technological implications; radiological and physical characterization; dismantling technology; decontamination technology; remotely operated equipment; means to reduce occupational exposures; waste generation and management, including clearance of solid materials; restricted and unrestricted site release, including final surveys; costs and financial provisions; safe enclosure of shutdown reactors, including long-term integrity of buildings and systems; decommissioning experience; and ageing management and refurbishment experience.

Decommissioning techniques for research reactors. Final report of a co-ordinated research project 1997-2001

International Nuclear Information System (INIS)

2002-02-01

in this technical publication. Operating experience in real-scale applications, lessons learned, key results in laboratory scale or pilot scale research, and validation of mathematical models, are among the most significant achievements of the CRP and have been highlighted. The objective of this CRP was to promote the exchange of information on the practical experience gained by Member States in decommissioning or operation, maintenance, and refurbishment activities which would be eventually related to the decommissioning of research reactors. Special emphasis was given to the development/adaptation of methods and approaches for optimization of the decommissioning process. The scope of the project included several technical areas of decommissioning rather than focusing on a single aspect of it. It was felt that this format would generate more awareness of the integrated approach to decommissioning. In particular, the scope included the following: design, construction and operational features to assist in final decommissioning; planning for decommissioning, including technical solution assessment; decommissioning strategies and their technological implications; radiological and physical characterization; dismantling technology; decontamination technology; remotely operated equipment; means to reduce occupational exposures; waste generation and management, including clearance of solid materials; restricted and unrestricted site release, including final surveys; costs and financial provisions; safe enclosure of shutdown reactors, including long-term integrity of buildings and systems; decommissioning experience; and ageing management and refurbishment experience

Molt salts reactors capacity for wastes incineration and energy production

International Nuclear Information System (INIS)

David, S.; Nuttin, A.

2005-01-01

The molten salt reactors present many advantages in the framework of the IV generation systems development for the energy production and/or the wastes incineration. After a recall of the main studies realized on the molten salt reactors, this document presents the new concepts and the identified research axis: the MSRE project and experience, the incinerators concepts, the thorium cycle. (A.L.B.)

105-C Reactor interim safe storage project technology integration plan

International Nuclear Information System (INIS)

Pulsford, S.K.

1997-01-01

The 105-C Reactor Interim Safe Storage Project Technology Integration Plan involves the decontamination, dismantlement, and interim safe storage of a surplus production reactor. A major goal is to identify and demonstrate new and innovative D and D technologies that will reduce costs, shorten schedules, enhance safety, and have the potential for general use across the RL complex. Innovative technologies are to be demonstrated in the following areas: Characterization; Decontamination; Waste Disposition; Dismantlement, Segmentation, and Demolition; Facility Stabilization; and Health and Safety. The evaluation and ranking of innovative technologies has been completed. Demonstrations will be selected from the ranked technologies according to priority. The contractor team members will review and evaluate the demonstration performances and make final recommendations to DOE

Final Report: Safety of Plasma Components and Aerosol Transport During Hard Disruptions and Accidental Energy Release in Fusion Reactor

Energy Technology Data Exchange (ETDEWEB)

Bourham, Mohamed A.; Gilligan, John G.

1999-08-14

Safety considerations in large future fusion reactors like ITER are important before licensing the reactor. Several scenarios are considered hazardous, which include safety of plasma-facing components during hard disruptions, high heat fluxes and thermal stresses during normal operation, accidental energy release, and aerosol formation and transport. Disruption events, in large tokamaks like ITER, are expected to produce local heat fluxes on plasma-facing components, which may exceed 100 GW/m{sup 2} over a period of about 0.1 ms. As a result, the surface temperature dramatically increases, which results in surface melting and vaporization, and produces thermal stresses and surface erosion. Plasma-facing components safety issues extends to cover a wide range of possible scenarios, including disruption severity and the impact of plasma-facing components on disruption parameters, accidental energy release and short/long term LOCA's, and formation of airborne particles by convective current transport during a LOVA (water/air ingress disruption) accident scenario. Study, and evaluation of, disruption-induced aerosol generation and mobilization is essential to characterize database on particulate formation and distribution for large future fusion tokamak reactor like ITER. In order to provide database relevant to ITER, the SIRENS electrothermal plasma facility at NCSU has been modified to closely simulate heat fluxes expected in ITER.

Technical Report Series on Global Modeling and Data Assimilation. Volume 40; Soil Moisture Active Passive (SMAP) Project Assessment Report for the Beta-Release L4_SM Data Product

Science.gov (United States)

Koster, Randal D.; Reichle, Rolf H.; De Lannoy, Gabrielle J. M.; Liu, Qing; Colliander, Andreas; Conaty, Austin; Jackson, Thomas; Kimball, John

2015-01-01

During the post-launch SMAP calibration and validation (Cal/Val) phase there are two objectives for each science data product team: 1) calibrate, verify, and improve the performance of the science algorithm, and 2) validate the accuracy of the science data product as specified in the science requirements and according to the Cal/Val schedule. This report provides an assessment of the SMAP Level 4 Surface and Root Zone Soil Moisture Passive (L4_SM) product specifically for the product's public beta release scheduled for 30 October 2015. The primary objective of the beta release is to allow users to familiarize themselves with the data product before the validated product becomes available. The beta release also allows users to conduct their own assessment of the data and to provide feedback to the L4_SM science data product team. The assessment of the L4_SM data product includes comparisons of SMAP L4_SM soil moisture estimates with in situ soil moisture observations from core validation sites and sparse networks. The assessment further includes a global evaluation of the internal diagnostics from the ensemble-based data assimilation system that is used to generate the L4_SM product. This evaluation focuses on the statistics of the observation-minus-forecast (O-F) residuals and the analysis increments. Together, the core validation site comparisons and the statistics of the assimilation diagnostics are considered primary validation methodologies for the L4_SM product. Comparisons against in situ measurements from regional-scale sparse networks are considered a secondary validation methodology because such in situ measurements are subject to upscaling errors from the point-scale to the grid cell scale of the data product. Based on the limited set of core validation sites, the assessment presented here meets the criteria established by the Committee on Earth Observing Satellites for Stage 1 validation and supports the beta release of the data. The validation against

ETDR, The European Union's Experimental Gas-Cooled Fast Reactor Project

International Nuclear Information System (INIS)

Poette, Christian; Brun-Magaud, Valerie; Morin, Franck; Dor, Isabelle; Pignatel, Jean-Francois; Bertrand, Frederic; Stainsby, Richard; Pelloni, Sandro; Every, Denis; Da Cruz, Dirceu

2008-01-01

In the Gas-Cooled Fast Reactor (GFR) development plan, the Experimental Technology Demonstration Reactor (ETDR) is the first necessary step towards the electricity generating prototype GFR. It is a low power (∼50 MWth) Helium cooled fast reactor. The pre-conceptual design of the ETDR is shared between European partners through the GCFR Specifically Targeted Research Project (STREP) within the European Commission's 6. R and D Framework Program. After recalling the place of ETDR in the GFR development plan, the main reactor objectives, the role of the European partners in the different design and safety tasks, the paper will give an overview of the current design with recent progresses in various areas like: - Sub-assembly technology for the starting core (pin bundle with MOX fuel and stainless steel cladding). - The design of experimental advanced ceramic GFR fuel sub-assemblies included in several locations of the starting core. - Starting Core reactivity management studies model including experimental GFR sub-assemblies. - Neutron and radiation shielding calculations using a specific MCNP model. The model allows evaluation of the neutron doses for the vessel and internals and radiation doses for maintenance operations. - System design and safety considerations, with a reactor architecture largely influenced by the Decay Heat Removal strategy (DHR) for de-pressurized accidents. The design of the reactor raises a number of issues in terms of fuel, neutronics, thermal-hydraulics codes qualification as well as critical components (blowers, IHX, thermal barriers) qualification. An overview of the R and D development on codes and technology qualification program is presented. Finally, the status of international collaborations and their perspectives for the ETDR are mentioned. (authors)

A summary of lessons learned activities conducted at the OECD Halden Reactor Project

International Nuclear Information System (INIS)

Hallbert, B.P.

1997-01-01

A series of lessons learned studies have been conducted at the OECD Halden Reactor Project. The purpose of these lessons learned reports are to summarize knowledge and experience gained across a number of research project. This paper presents a summary of main issues addressed in four of these lessons learned projects. These are concerned with software development and quality assurance, software reliability, methods for test and evaluation of developed systems, and the evaluation of system design features

Reactor Physics Programme

Energy Technology Data Exchange (ETDEWEB)

De Raedt, C

2000-07-01

The Reactor Physics and Department of SCK-CEN offers expertise in various areas of reactor physics, in particular in neutronics calculations, reactor dosimetry, reactor operation, reactor safety and control and non-destructive analysis on reactor fuel. This expertise is applied within the Reactor Physics and MYRRHA Research Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 reactor dosimetry, and the preparation and interpretation of irradiation experiments. Progress and achievements in 1999 in the following areas are reported on: (1) investigations on the use of military plutonium in commercial power reactors; (2) neutron and gamma calculations performed for BR-2 and for other reactors; (3) the updating of neutron and gamma cross-section libraries; (4) the implementation of reactor codes; (6) the management of the UNIX workstations; and (6) fuel cycle studies.

Reactor Physics Programme

International Nuclear Information System (INIS)

De Raedt, C.

2000-01-01

The Reactor Physics and Department of SCK-CEN offers expertise in various areas of reactor physics, in particular in neutronics calculations, reactor dosimetry, reactor operation, reactor safety and control and non-destructive analysis on reactor fuel. This expertise is applied within the Reactor Physics and MYRRHA Research Department's own research projects in the VENUS critical facility, in the BR1 reactor and in the MYRRHA project (this project aims at designing a prototype Accelerator Driven System). Available expertise is also used in programmes external to the Department such as the reactor pressure steel vessel programme, the BR2 reactor dosimetry, and the preparation and interpretation of irradiation experiments. Progress and achievements in 1999 in the following areas are reported on: (1) investigations on the use of military plutonium in commercial power reactors; (2) neutron and gamma calculations performed for BR-2 and for other reactors; (3) the updating of neutron and gamma cross-section libraries; (4) the implementation of reactor codes; (6) the management of the UNIX workstations; and (6) fuel cycle studies

Growth and Expansion of the International Criticality Safety Benchmark Evaluation Project and the Newly Organized International Reactor Physics Experiment Evaluation Project

Energy Technology Data Exchange (ETDEWEB)

J. Blair Briggs; Lori Scott; Yolanda Rugama; Enrico Satori

2007-05-01

Since ICNC 2003, the International Criticality Safety Benchmark Evaluation Project (ICSBEP) has continued to expand its efforts and broaden its scope. Criticality-alarm / shielding type benchmarks and fundamental physics measurements that are relevant to criticality safety applications are not only included in the scope of the project, but benchmark data are also included in the latest version of the handbook. A considerable number of improvements have been made to the searchable database, DICE and the criticality-alarm / shielding benchmarks and fundamental physics measurements have been included in the database. There were 12 countries participating on the ICSBEP in 2003. That number has increased to 18 with recent contributions of data and/or resources from Brazil, Czech Republic, Poland, India, Canada, and China. South Africa, Germany, Argentina, and Australia have been invited to participate. Since ICNC 2003, the contents of the “International Handbook of Evaluated Criticality Safety Benchmark Experiments” have increased from 350 evaluations (28,000 pages) containing benchmark specifications for 3070 critical or subcritical configurations to 442 evaluations (over 38,000 pages) containing benchmark specifications for 3957 critical or subcritical configurations, 23 criticality-alarm-placement / shielding configurations with multiple dose points for each, and 20 configurations that have been categorized as fundamental physics measurements that are relevant to criticality safety applications in the 2006 Edition of the ICSBEP Handbook. Approximately 30 new evaluations and 250 additional configurations are expected to be added to the 2007 Edition of the Handbook. Since ICNC 2003, a reactor physics counterpart to the ICSBEP, The International Reactor Physics Experiment Evaluation Project (IRPhEP) was initiated. Beginning in 1999, the IRPhEP was conducted as a pilot activity by the by the Organization of Economic Cooperation and Development (OECD) Nuclear Energy

Project WAGR: The UK demonstration project for power reactor decommissioning - removing the core and looking to completion

International Nuclear Information System (INIS)

Benest, T. G.

2003-01-01

delivered the required performance. In such cases, simple tooling and manual intervention have been adopted to maintain the project ahead of programme and below the dose budget. For campaigns where manual intervention was precluded by high dose rates, the contractor has undertaken a risk assessment of each task and elected to develop a number of different tools to cover the most likely risks. Although this strategy incurs costs for tools that may never be utilised, these costs are dwarfed by the project costs of potential delays. Excellent progress has been maintained throughout the remote dismantling with the reliability of the equipment and the experience of the workforce being major contributors to the success. Management arrangements have also contributed to the current excellent programme position. The close working relationship between UKAEA and their prime contractor, and management of the interfaces with the regulators, has enabled problems to be identified early and then dealt with quickly and effectively. The current phase of operations is now planned for completion in early 2005 over 18 months ahead of programme. Currently the WAGR project has operated for over 6 years without a lost time accident to either UKAEA staff or any of the contractor's operatives. In the last 12 months, the maximum radiation dose to an individual was <1.0 mSv. To date, 270 tonnes of graphite and 206 tonnes of steel have been encapsulated. 38 boxes of low level waste have been sent, or are awaiting transport, to BNFL's Drigg site for disposal, and a further 102 boxes of ILW are now stored on-site pending the availability of a national facility. Thus far the UKAEA WAGR project is well ahead of programme, achieving all its objectives and demonstrating to a world-wide audience that a power reactor can be decommissioned safely and efficiently shortly after shutdown

Investigation of the noble metal deposition behaviour in boiling water reactors - the NORA project

International Nuclear Information System (INIS)

Ritter, S.; Karastoyanov, V.; Abolhassani-Dadras, S.; Guenther-Leopold, I.; Kivel, N.

2010-01-01

NobleChem™ is a technology developed by General Electric to reduce stress corrosion cracking (SCC) in reactor internals and recirculation pipes of boiling water reactors (BWRs) while preventing the negative side effects of classical hydrogen water chemistry. Noble metals (Pt, Rh) acting as electrocatalysts for the recombination of O 2 and H 2 O 2 with H 2 to H 2 O and thus reducing the corrosion potential more efficiently are injected into the feed water during reactor shut-down (classical method) or on-line during power operation. They are claimed to deposit as very fine metallic particles on all water-wetted surfaces including the most critical regions inside existing cracks and to stay electrocatalytic over long periods of time. The effectiveness of this technology in plants remains still to be demonstrated. Based on highly credible laboratory experiments down to the sub-ppb Pt concentration range, SCC mitigation may be expected, provided that a stoichiometric excess of H 2 and a sufficient surface coverage with very fine Pt particles exist simultaneously at the critical locations. Very little is known about the deposition and (re-)distribution behaviour of the Pt in the reactor. For the validation of this technique the research project NORA (noble metal deposition behaviour in BWRs) has been started at PSI with two main objectives: (i) to gain phenomenological insights and a better basic understanding of the Pt distribution and deposition behaviour in BWRs; (ii) to develop and qualify a non-destructive technique to characterise the size and distribution of the Pt particles and its local concentration on reactor components. This paper presents the objectives of the project, the planned work and a brief description of the status of the project. (author)

Releases of radioactive substances from Swedish nuclear power plants (RAKU)

Energy Technology Data Exchange (ETDEWEB)

Ingemansson, T.; Bergstroem, C. [ALARA Engineering AB, Skultuna (Sweden)

1997-04-01

Releases of radioactivity to air and water from Swedish nuclear power plants have been studied and compared with those from foreign reactors. Averaged over the years from commissioning of the reactors to the last year data are available, the release of radioactive noble gas from the Swedish BWRs has been about the same as from comparable foreign reactors. The oldest Swedish BWRs, Oskarshamn 1 and 2 (O1 and O2) and Ringhals 1 (R1), have simple off-gas systems with only one delay volume. All BWRs in US, Germany, Japan and Switzerland are equipped with more sophisticated off-gas systems. It can be expected that O1, O2 and R1 therefore will have the highest release of noble gas activity at an international comparison if they do not modernize their off-gas system. BWRs in US, Germany and Japan are today equipped with recombiners and with one exception also charcoal columns. Japanese BWRs report zero releases to air. Releases of radioactivity to water after commissioning was about the same for most of the studied reactors. Some of the newest German plants have had low annual releases already at commissioning. Improvements of the treatment systems at old German, Swiss and US reactors have significantly lowered the releases. For most of the Swedish plants the annual releases to water have remained at the initial level. Forsmark 3 has succeeded in decreasing the release of radionuclides to water by a factor of almost one hundred compared to other Swedish reactors. Also O3 has managed to decrease the liquid effluents. Japanese plants have zero release of radioactivity excluding tritium to water. The release of tritium is about the same for all reactors of the same type in the world. 35 refs, 31 figs, 24 tabs.

Pressurized water reactors: the EPR project

International Nuclear Information System (INIS)

Py, J.P.; Yvon, M.

2007-01-01

EPR (originally 'European pressurized water reactor', and now 'evolutionary power reactor') is a model of reactor initially jointly developed by French and German engineers which fulfills the particular safety specifications of both countries but also the European utility requirements jointly elaborated by the main European power companies under the initiative of Electricite de France (EdF). Today, two EPR-based reactors are under development: one is under construction in Finland and the other, Flamanville 3 (France), received its creation permit decree on April 10, 2007. This article presents, first, the main objectives of the EPR, and then, describes the Flamanville 3 reactor: reactor type and general conditions, core and conditions of operation, primary and secondary circuits with their components, main auxiliary and recovery systems, man-machine interface and instrumentation and control system, confinement and serious accidents, arrangement of buildings. (J.S.)

Relative Release-to-Birth Indicators for Investigating TRISO Fuel Fission Gas Release Models

International Nuclear Information System (INIS)

Harp, Jason M.; Hawari, Ayman I.

2008-01-01

TRISO microsphere fuel is the fundamental fuel unit for Very High Temperature Reactors (VHTR). A single TRISO particle consists of an inner kernel of uranium dioxide or uranium oxycarbide surrounded by layers of pyrolytic carbon and silicon carbide. If the silicon carbide layer fails, fission products, especially the noble fission gases Kr and Xe, will begin to escape the failed particle. The release of fission gas is usually quantified by measuring the ratio of the released activity (R) to the original birth activity (B), which is designated as the R/B ratio. In this work, relative Release-to-Birth indicators (I) are proposed as a technique for interpreting the results of TRISO irradiation experiments. By implementing a relative metric, it is possible to reduce the sensitivity of the indicators to instrumental uncertainties and variations in experimental conditions. As an example, relative R/B indicators are applied to the interpretation of representative data from the Advanced Gas Reactor-1 TRISO fuel experiment that is currently taking place at the Advanced Test Reactor of Idaho National Laboratory. It is shown that the comparison of measured to predicted relative R/B indicators (I) gives insight into the physics of release and helps validate release models. Different trends displayed by the indicators are related to the mechanisms of fission gas release such as diffusion and recoil. The current analysis shows evidence for separate diffusion coefficients for Kr and Xe and supports the need to account for recoil release. (authors)

Recommendations concerning models and parameters best suited to breeder reactor environmental radiological assessments

International Nuclear Information System (INIS)

Miller, C.W.; Baes, C.F. III; Dunning, D.E. Jr.

1980-05-01

Recommendations are presented concerning the models and parameters best suited for assessing the impact of radionuclide releases to the environment by breeder reactor facilities. These recommendations are based on the model and parameter evaluations performed during this project to date. Seven different areas are covered in separate sections

The CAREM reactor and present currents in reactor design

International Nuclear Information System (INIS)

Ordonez, J.P.

1990-01-01

INVAP has been working on the CAREM project since 1983. It concerns a very low power reactor for electrical energy generation. The design of the reactor and the basic criteria used were described in 1984. Since then, a series of designs have been presented for reactors which are similar to CAREM regarding the solutions presented to reduce the chance of major nuclear accidents. These designs have been grouped under different names: Advanced Reactors, Second Generation Reactors, Inherently Safe Reactors, or even, Revolutionary Reactors. Every reactor fabrication firm has, at least, one project which can be placed in this category. Presently, there are two main currents of Reactor Design; Evolutionary and Revolutionary. The present work discusses characteristics of these two types of reactors, some revolutionary designs and common criteria to both types. After, these criteria are compared with CAREM reactor design. (Author) [es

Jules Horowitz reactor - presentation of the project and progress report

International Nuclear Information System (INIS)

Ballagny, A.; Frachet, S.; Rommens, M.; Guigon, B.; Minguet, J.L.; Dupuy, J.P.; Leydier, C.

2001-01-01

The RJH project was launched by CEA some years ago, with the objective to replace, after 2010, the material testing reactors of the previous generation. The objectives are also: to realise a significant step in term of performances, to ensure a high flexibility of the design, in order to host in the future new experiments, which are not completely defined at the project stage, to reach a high level of safety, according to the best current practice. After a summary of the main experimental objectives of the facility, the present paper deals with a detailed technical presentation of the project, resulting from preliminary design studies. The following topics are covered successively: the main functionalities, the resulting design options and technical solutions, the layout of the nuclear facility. (orig.)

GROWTH OF THE INTERNATIONAL CRITICALITY SAFETY AND REACTOR PHYSICS EXPERIMENT EVALUATION PROJECTS

Energy Technology Data Exchange (ETDEWEB)

J. Blair Briggs; John D. Bess; Jim Gulliford

2011-09-01

Since the International Conference on Nuclear Criticality Safety (ICNC) 2007, the International Criticality Safety Benchmark Evaluation Project (ICSBEP) and the International Reactor Physics Experiment Evaluation Project (IRPhEP) have continued to expand their efforts and broaden their scope. Eighteen countries participated on the ICSBEP in 2007. Now, there are 20, with recent contributions from Sweden and Argentina. The IRPhEP has also expanded from eight contributing countries in 2007 to 16 in 2011. Since ICNC 2007, the contents of the 'International Handbook of Evaluated Criticality Safety Benchmark Experiments1' have increased from 442 evaluations (38000 pages), containing benchmark specifications for 3955 critical or subcritical configurations to 516 evaluations (nearly 55000 pages), containing benchmark specifications for 4405 critical or subcritical configurations in the 2010 Edition of the ICSBEP Handbook. The contents of the Handbook have also increased from 21 to 24 criticality-alarm-placement/shielding configurations with multiple dose points for each, and from 20 to 200 configurations categorized as fundamental physics measurements relevant to criticality safety applications. Approximately 25 new evaluations and 150 additional configurations are expected to be added to the 2011 edition of the Handbook. Since ICNC 2007, the contents of the 'International Handbook of Evaluated Reactor Physics Benchmark Experiments2' have increased from 16 different experimental series that were performed at 12 different reactor facilities to 53 experimental series that were performed at 30 different reactor facilities in the 2011 edition of the Handbook. Considerable effort has also been made to improve the functionality of the searchable database, DICE (Database for the International Criticality Benchmark Evaluation Project) and verify the accuracy of the data contained therein. DICE will be discussed in separate papers at ICNC 2011. The status of the

The aqueous homogeneous suspension reactor project

International Nuclear Information System (INIS)

1975-01-01

The power of the KSTR reactor has been increased up to 200 kW in the fourth quarter of 1974. A description is given of the behaviour of the reactor at increased power level, safety aspects concerned with this new level, the operation of the reactor, instrumental behavior and mechanical behavior. Irradiation investigation of two types of fuels are reported and results are presented. Progress made on the conceptual design of a 250 MWe suspension reactor is described

User's guide to GASPAR code (a computer program for calculating radiation exposure to man from routine air releases of nuclear reactor effluents). Technical report

International Nuclear Information System (INIS)

Eckerman, K.F.; Congel, F.J.; Roecklein, A.K.; Pasciak, W.J.

1980-06-01

The document is a user's guide for the GASPAR code, a computer program written for the evaluation of radiological impacts due to the release of radioactive material to the atmosphere during normal operation of light water reactors. The GASPAR code implements the radiological impact models of NRC Regulatory Guide 1.109, Revision 1, for atmospheric releases. The code is currently used by NRC in reactor licensing evaluations to estimate (1) the collective or population dose to the population within a 50-mile radius of a facility, (2) the total collective dose to the U.S. population, and (3) the maximum individual doses at selected locations in the vicinity of the plant

NKS/RAK-2. Protection against radioactive release in reactor accidents

International Nuclear Information System (INIS)

Lindholm, I.

1995-01-01

The work scope of RAK-2 project is divided into three subprojects: 1. Severe accident phenomenology. 2. Computerized accident management. 3. Reactors in Nordic surroundings. All three subprojects are ongoing. The project work on three subareas is in general progressing according to the time schedule and budget. The construction of melt jet breakup test facility at Kungliga Tekniska Hoegskolan (KTH) has been delayed due to complexity of the test arrangement and due to meeting the necessary safety requirements connected to tests mixing water and high temperature melts. Because of the delay in melt jet break up tests a slight redirection of the KTH work for NKS was taken. The present KTH work concentrates on theoretical studies of melt pool behavior in the lower head and on theoretical/experimental studies on core melt discharge from the pressure vessel failure. It is expected that single drop melt-water interaction experiments to study the thermal fragmentation phenomenon will begin in very early 1996. The recriticality studies are well underway, but the work is proposed to continue in 1996 to get more analyses carried out. (au)

Vietnam Project For Production Of Radioactive Beam Based On ISOL Technique With The Dalat Reactor

International Nuclear Information System (INIS)

Le Hong Khiem; Phan Viet Cuong; Fadi Ibrahim

2011-01-01

The presence in Vietnam of Dalat nuclear reactor dedicated to fundamental studies is a unique opportunity to produce Radioactive Ion (RI) Beams with the fission of a 235 U induced by the thermal neutrons produced by the reactor. We propose to produce RI beams at the Dalat nuclear reactor using ISOL (Isotope Separation On-Line) technique. This project should be a unique opportunity for Vietnamese nuclear physics community to use its own facilities to produce RI beams for studying nuclear physics at an international level. (author)

Uncertainties in modeling of consequences of tritium release from fusion reactors. Plasma Fusion Center No. PFC/TR-79-5

International Nuclear Information System (INIS)

Piet, S.J.; Kazimi, M.S.

1979-07-01

The bases for various models concerned with all phases of estimating doses from routine tritium releases from fusion reactors have been examined. The implications of uncertainties in parameters and assumptions for the uncertainty of the calculated doses and resulting maximum permissible releases are presented. Global dispersion models are most affected by the assumptions made concerning movement, such as the role of the ocean as a sink. Dose models were generally found to agree within a factor of two, with the largest variation due to agricultural data. Plant tritium flow studies are the least developed and require substantial improvement in the data base. Based on two possible arbitrary global standards, the maximum allowable releases were found to range from 1.6 to 20,000 Ci/day. The local criteria imply releases between 5 and 20 Ci/day

The radiological consequences of notional accidental releases of radioactivity from fast breeder reactors: the influence of the meteorological conditions

International Nuclear Information System (INIS)

Hemming, C.R.; Hallam, J.; Kelly, G.N.

1980-04-01

The radiological consequences of a wide range of notional accidental releases from a 1300 MW(e) LMFBR (liquid Metal-cooled Fast Breeder Reactor) were assessed in a previous study by the National Radiological Protection Board. In the present study the sensitivity of the predicted consequences to the meteorological conditions was investigated. The influence of the wind direction, and hence the distribution of the exposed population, and of atmospheric stability at the time of the release are considered separately. Conclusions are reached on the precision required in specifying atmospheric stability conditions to estimate reliably the distribution of possible consequences following a given release of activity. The probability distributions of consequences for selected releases from two locations are evaluated taking account of the frequency distribution of wind direction and atmospheric stability at each location. The variation is large and demonstrates the importance of taking account of the whole range of meteorological conditions when assessing the risk presented by an accidental release of activity. (author)

Fast nuclear reactors. Associated international projects. State of the art and assessment of the concepts

International Nuclear Information System (INIS)

Azpitarte, O.; Ramilo, L.

2013-01-01

The recognition of the strategic importance of nuclear energy as a source of sustainable energy may be perceived in the continuous development, in many countries, of the technology of fast nuclear reactors with an associated closed fuel cycle, assuming that these Generation IV innovative systems will be required in the future. These reactors fulfill international requirements for safety and reliability, economic competitiveness, sustainability and proliferation resistance. They have the potential of using more efficiently the natural resources of Uranium and of reducing the volume and radiotoxicity of the nuclear waste by partitioning and transmutation of Minor Actinides. The national and international programs being carried out today are concentrated in the following concepts: Sodium Fast Reactor (SFR), Lead Fast Reactor (LFR), Gas Fast Reactor (GFR), Super Critical Water Reactor (SCWR) and Molten Salt Reactor (MSR). This article presents a short review of the technology of the mentioned concepts and details the current state of the main national and international related projects. (author)

Design Project on Controlled-Release Drug Delivery Devices: Implementation, Management, and Learning Experiences

Science.gov (United States)

Xu, Qingxing; Liang, Youyun; Tong, Yen Wah; Wang, Chi-Hwa

2010-01-01

A design project that focuses on the subject of controlled-release drug delivery devices is presented for use in an undergraduate course on mass transfer. The purpose of the project is to introduce students to the various technologies used in the fabrication of drug delivery systems and provide a practical design exercise for understanding the…

Final project report: TA-35 Los Alamos Power Reactor Experiment No. II (LAPRE II) decommissioning project

International Nuclear Information System (INIS)

Montoya, G.M.

1993-02-01

This final report addresses the decommissioning of the LAPRE II Reactor, safety enclosure, fuel reservoir tanks, emergency fuel recovery system, primary pump pit, secondary loop, associated piping, and the post-remediation activities. Post-remedial action measurements are also included. The cost of the project including, Phase I assessment and Phase II remediation was approximately $496K. The decommissioning operation produced 533 M 3 of mixed waste

EPR: The reactor generation for the 21st century. SFEN-KTG congress 'The EPR Project'', Strasbourg, 13-14 Nov. 1994

International Nuclear Information System (INIS)

Anon.

1995-01-01

The foundation of the subsidiary in 1989, Nuclear Power International (NPI), brought together as partners the two formerly competing companies Siemens/KWU and Framatome who now are planning the novel reactor type within the framework of the joint EPR project. The project goal is to develop a novel French-German PWR reactor type for power generation, named European Pressurized Water Reactor (EPR). The article summarizes the main results of papers and discussions of the congress. (orig./UA) [de

Electronuclear reactors - EDF - Orientations of generic studies to be performed for the safety re-examination of 1300 MWe reactors associated to their third decennial inspection

International Nuclear Information System (INIS)

2011-01-01

This report expresses the ASN's opinion on the framework and objectives of the EDF program concerning the generic studies of the safety re-examination of the 1300 MWe reactors associated with their third decennial inspection. This comprises lessons from the Fukushima accident, the improvement of the 'internal explosion' referential by using a probabilistic study, the application of the seismic margin assessment approach as soon as possible, checking the absence of any 'cliff effect' for cooling functions, a deepened re-examination of hurricane frequencies in France. Other request by the ASN concern the verification of the pertinence of release authorizations, taking the TSN law into account, taking the AP1300 project into account, the expansion of the complementary domain, the project of reactor lifetime extension. Some technical requests are discussed in appendix

Nuclear reactor for release of nuclear energy, without a chain reaction using the simultaneous implosion of three, or more, atomic nuclei

International Nuclear Information System (INIS)

Pedrick, A.P.

1976-01-01

A modified form of what is known as a 'streaking nuclear reactor' is described. In this type of reactor it is proposed to obtain release of nuclear energy from atomic nuclei by stripping such nuclei of their electron clouds or shells, to form a high temperature plasma, and breaking nucleons off the surface of the nuclei. In the apparatus described it is proposed to break up nuclei by causing three or more nuclei to collide with each other at very high velocity. Streams of nuclei, stripped of their electron clouds are directed into a reactor vessel to a focal point or implosion center along three or more ducts, equi-angularly spaced around the implosion center in the same plane, the arrangement being such as to permit mutual simultaneous collision of three or more of the nuclei. The importance of achieving a release of nuclear energy in this manner is that it may be able to use any chemical element that can be converted to a plasma, but it is most likely to be successful with elements of high atomic number, such as Pb or Bi. (U.K.)

Decommissioning of the research nuclear reactor WWR-S Magurele - Bucharest. General presentation of the project

International Nuclear Information System (INIS)

Dragulescu, Emilian; Dragusin, Mitica; Popa, Victor; Boicu, Alin; Tuca, Carmen; Iorga, Ioan; Vrabie, Ionut; Mustata, Carmen

2003-01-01

A decommissioning project was worked out concerning the nuclear facility research reactor WWR-S Magurele-Bucharest to remove the radioactive and hazardous materials and so to exclude any risk for human health and environment. The project involves the four phases named assessment, development, operations and closeout. There are two major parts to the assesment phase: preliminary characterisation and the review and decision-making process. Characterisation is needed to develop project baseline data, which should include sufficient chemical, physical, and radiological characterisation to meet planning needs. Based on the conclusions of these studies, possible decommissioning alternative will be analyzed and: the best alternative chosen, final goal identified, risk assessments are evaluated. Also, taken into account are: regulations supporting assessment, land use considerations, financial concerns, disposal availability, public involvement, technology developments. After a decommissioning alternative was chosen, detailed engineering will begin following appropriate regulatory guidance. The plan will include characterisation information, namely: review of decommissioning alternatives; justification for the selected alternative; provision for regulatory compliance; predictions of personnel exposure, radioactive waste volume, and cost. Other activities are: scheduling, preparation for decommissioning operations; coordination, documentation, characterization report, feasibility studies, Decommissioning Plan, project daily report, radiological survey, airborne sampling records, termination survey of the site. The operations imply: identification and sequencing the operations on contaminated materials, storing on site the wastes, awaiting processing or disposal, and packaging of materials for transport to processing or disposal facilities.The key operations are: worker protection, health and safety program, review of planing work, work area assessment, work area controls

An overview of the U.S. Department of Energy Experimental Boiling Water Reactor Decontamination and Decommissioning Project

International Nuclear Information System (INIS)

Murphie, W.E.; Mckernan, M.L.

1991-01-01

This paper provides an overview of the U.S. Department of Energy's (DOE) Experimental Boiling Water Reactor (EBWR) Decontamination and Decommissioning (D and D) Project. Physical decommissioning work started in 1986 and is scheduled for completion in 1994. The project total estimated cost is 14.3 million (1990, U.S.) dollars. The reactor pressure vessel will be removed by segmentation. Another notable project feature is that D and D operations were planned for and carried out with a small work force comprised of four to six D and D laborers, one or two health physics technicians, an engineer, and a project manager. When the D and D work is completed the facility will be recycled for other productive uses. (author)

Final Report: Safety of Plasma-Facing Components and Aerosol Transport During Hard Disruptions and Accidental Energy Release in Fusion Reactor

International Nuclear Information System (INIS)

Bourham, Mohamed A.; Gilligan, John G.

1999-01-01

Safety considerations in large future fusion reactors like ITER are important before licensing the reactor. Several scenarios are considered hazardous, which include safety of plasma-facing components during hard disruptions, high heat fluxes and thermal stresses during normal operation, accidental energy release, and aerosol formation and transport. Disruption events, in large tokamaks like ITER, are expected to produce local heat fluxes on plasma-facing components, which may exceed 100 GW/m 2 over a period of about 0.1 ms. As a result, the surface temperature dramatically increases, which results in surface melting and vaporization, and produces thermal stresses and surface erosion. Plasma-facing components safety issues extends to cover a wide range of possible scenarios, including disruption severity and the impact of plasma-facing components on disruption parameters, accidental energy release and short/long term LOCA's, and formation of airborne particles by convective current transport during a LOVA (water/air ingress disruption) accident scenario. Study, and evaluation of, disruption-induced aerosol generation and mobilization is essential to characterize database on particulate formation and distribution for large future fusion tokamak reactor like ITER. In order to provide database relevant to ITER, the SIRENS electrothermal plasma facility at NCSU has been modified to closely simulate heat fluxes expected in ITER

Analysis of radiological accident emissions of a lead-cooled experimental reactor. LEADER Project; Analisis radiologico de las emisiones en caso de accidente de un reactor experimental refrigerado por plomo. Proyecto LEADER

Energy Technology Data Exchange (ETDEWEB)

Gomez Salcedo, F.; Cortes Martin, A.

2013-07-01

The LEADER project develops a conceptual level industrial size reactor cooled lead and a demonstration plant of this technology. The project objectives are to define the characteristics and design to installation scale reactor using available technologies and short-term components and assess safety aspects conducting a preliminary analysis of the impact of the facility.

IFPE/RISOE-II, Fuel Performance Data from Transient Fission Gas Release

International Nuclear Information System (INIS)

Turnbull, J.A.

1995-01-01

Description: The RISO National Laboratory in Denmark have carried out three irradiation programs of slow ramp and hold tests, so called 'bump tests' to investigate fission gas release and fuel microstructural changes. The second project took place between 1982 and 1986 and was called 'The RISO Transient Fission Gas Project'. The fuel used in the project was from: IFA-161 irradiated in the Halden BWR (27 to 42 MWd/kgUO 2 ) and GE BWR fuel irradiated in the Millstone 1 reactor 14 to 29 MWd/kgUO 2 . Using the re-fabrication technique, it was possible to back fill the test segment with a choice of gas and gas pressure and to measure the time dependence of fission gas release by continuous monitoring of the plenum pressure. The short length of the test segment was an advantage because, depending on where along the original rod the section was taken, burnup could be chosen variable, and during the test the fuel experienced a single power

Measurements at the RA Reactor related to the VISA-2 project - Part 1, Start-up of the RA reactor and measurement of new RA reactor core parameters

International Nuclear Information System (INIS)

Markovic, H.

1962-07-01

The objective of the measurements was determining the neutron flux in the RA reactor core. Since the number of fuel channels is increased from 56 to 68 within the VISA-2 project, it was necessary to attain criticality of the RA reactor and measure the neutron flux properties. The 'program of RA reactor start-up' has been prepared separately and it is included in this report. Measurements were divided in two phases. First phase was measuring of the neutron flux after the criticality was achieved but at zero power. During phase two measurements were repeated at several power levels, at equilibrium xenon poisoning. This report includes experimental data of flux distributions and absolute values of the thermal and fast neutron flux in the RA reactor experimental channels and values of cadmium ratio for determining the neutron epithermal flux. Data related to calibration of regulatory rods for cold un poisoned core are included [sr

The reprocessing of fast reactor fuels - the TOR project

International Nuclear Information System (INIS)

Calame-Longjean, A.; Le Bouhellec, J.; Schwob, Y.

1982-01-01

A description is given of development work on the proposed new French facility for the reprocessing of fast reactor fuel. This is the TOR facility (Traitement des Oxydes Rapides). Block diagrams give details of the TOR project as a whole and of the main line and R and D line of the TOR 1 facility which is a new works devoted to the head of the process. Modifications to existing plant which will form the TOR 2 and TOR 3 facilities are also described. (U.K.)

Project in fiscal 1988 for research and development of basic technologies in next generation industries. Achievement report on research and development of bio-reactors; 1988 nendo bio reactor no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-03-01

Research and development has been performed on bio-reactors to substitute the oxidizing reaction process, and on reduction reacting bio-reactors to fix the coenzyme regeneration system. This paper summarizes the achievements in fiscal 1988. In the research of a bio-reactor using bacteria that produce muconic acid from benzoic acid, stable productivity of 60 g/L/day or more was obtained. In the research of a multi-phase based bio-reactor composed of air, oil, water and biomass, discussions were given on the phase inverting film permeation type reactor. In the research of a bio-reactor to produce acetic acid from carbon dioxide and hydrogen, productivity of 149 g/L/day as maximum was achieved by enhancing the production speed by means of pressurization. In the research of a bio-reactor to produce hydroquinone from phenol, up-keeping the duration for 100 hours or longer has become possible at the hydroquinone production speed of 3 g/L/h. In the research of a reduction-based bio-reactor incorporating the regeneration system of coenzyme NAD(P)H, discussions were given on optimizing the continuous enzymatic reaction in the production of sorbitol. (NEDO)

Thermophysical properties database of materials for light water reactors and heavy water reactors. Final report of a coordinated research project 1999-2005

International Nuclear Information System (INIS)

2006-06-01

The IAEA Coordinated Research Project (CRP) on the Establishment of a Thermo-physical Properties Database for Light Water Reactors (LWRs) and Heavy Water Reactors (HWRs) started in 1999. It was included in the IAEA's Nuclear Power Programme following endorsement in 1997 by the IAEA's Technical Working Groups on Advanced Technologies for LWRs and HWRs (the TWG-LWR and the TWG-HWR). Furthermore, the TWG on Fuel Performance and Technology (TWG-FPT) also expressed its support. This CRP was conducted as a joint task within the IAEA's project on technology development for LWRs and HWRs in its nuclear power programme. Improving the technology for nuclear reactors through better computer codes and more accurate materials property data can contribute to improved economics of future plants by helping to remove the need for large design margins, which are currently used to account for limitations of data and methods. Accurate representations of thermo-physical properties under relevant temperature and neutron fluence conditions are necessary for evaluating reactor performance under normal operation and accident conditions. The objective of this CRP was to collect and systematize a thermo-physical properties database for light and heavy water reactor materials under normal operating, transient and accident conditions and to foster the exchange of non-proprietary information on thermo-physical properties of LWR and HWR materials. An internationally available, peer reviewed database of properties at normal and severe accident conditions has been established on the Internet. This report is intended to serve as a useful source of information on thermo-physical properties data for water cooled reactor analyses. The properties data have been initially stored in the THERSYST data system at the University of Stuttgart, Germany, which was subsequently developed into an internationally available Internet database named THERPRO at Hanyang University, Republic of Korea

The aqueous homogeneous suspension reactor project

International Nuclear Information System (INIS)

1976-01-01

During 1975, reactor power has been increased to the design power of 1000 KW, whereas power fluctuations show a decrease with increased mean power. Operation experience with the reactor and associated instrumentation during 1975 is described. The results of the experiments done for fuel irradiations and investigations in the KSTR fuel, mainly to determine the amount of erosion products on the fuel, are described. Concerning the safety of operation of the KSTR reactor, several actions had to be taken mainly to replace or repair components or instrumentation of the reactor. Radiological safety and radioactivity discharges during 1975 are reported

Reduction of fuel enrichment for research reactors built-up in accordance with Russian (Soviet) projects

International Nuclear Information System (INIS)

Aleksandrov, A.B.; Enin, A.A.; Tkachyov, A.A.

2001-01-01

In accordance with the Russian program of reduced enrichment for research and test reactors (RERTR) built-up in accordance with Russian (Soviet) projects, AO 'NCCP' performs works on FA fabrication with reduced enrichment fuel. The main trends and results of performed works on research reactors FEs and FAs based on UO 2 and U-9%Mo fuel with U 235 19.7% enrichment are described. (author)

Release of WIMS10: a versatile reactor physics code for thermal and fast systems - 15467

International Nuclear Information System (INIS)

Lindley, B.A.; Newton, T.D.; Hosking, J.G.; Smith, P.N.; Powney, D.J.; Tollit, B.; Smith, P.J.

2015-01-01

the WIMS code provides a versatile software package for neutronic calculations, which can be applied to all thermal reactor types including mixed moderator systems. It can provide lattice cell and supercell calculations using a range of flux solutions methods to produce the neutronic libraries for use in PANTHER or other whole core analysis codes. With the release of WIMS10, the range of problems which WIMS can solve has been greatly extended. A WIMS/PANTHER calculation route has been developed and validated for part MOX-fuelled PWRs, with calculations showing excellent agreement with 2D core deterministic and Monte Carlo transport solutions. A flexible geometry 3D method of characteristics transport solver, CACTUS3D has been added to the code. CACTUS3D has been benchmarked for a 3D BWR assembly model, and was in good agreement with a direct 172-group solution in the Monte Carlo code MONK. Fast reactor calculations using the ECCO deterministic calculation route have been validated using experimental data from the ZEBRA reactor. Power deposition can be treated through following neutrons and/or photons to their point of interaction. The improved methodology is shown to give more accurate calculation of heat deposition and improve agreement between calculated and measured detector responses for part MOX-fuelled cores. (authors)

Best-practices guidelines for L2PSA development and applications. Volume 2 - Best practices for the Gen II PWR, Gen II BWR L2PSAs. Extension to Gen III reactors

International Nuclear Information System (INIS)

Raimond, E.; Durin, T.; Rahni, N.; Meignen, R.; Cranga, M.; Pichereau, F.; Bentaib, A.; Guigueno, Y.; Loeffler, H.; Mildenberger, O.; Lajtha, G.; Santamaria, C.S.; Dienstbier, J.; Rydl, A.; Holmberg, J.E.; Lindholm, I.; Maennistoe, I.; Pauli, E.M.; Dirksen, G.; Grindon, L.; Peers, K.; Hulqvist, G.; Parozzi, F.; Polidoro, F.; Cazzoli, E.; Vitazkova, J.; Burgazzi, L.; Oury, L.; Ngatchou, C.; Siltanen, S.; Niemela, I.; Routamo, T.; Helstroem, P.; Bassi, C.; Brinkman, H.; Seidel, A.; Schubert, B.; Wohlstein, R.; Guentay, S.; Vincon, L.

2010-01-01

The objective of this coordinated action was to develop best practice guidelines for the performance of Level 2 PSA methodologies with a view of harmonisation at EU level and to allow meaningful and practical uncertainty evaluations in a Level 2 PSA. Specific relationships with community in charge of nuclear reactor safety (utilities, safety authorities, vendors, and research or services companies) have been established in order to define the current needs in terms of guidelines for level 2 PSA development and applications. An international workshop was organised in Hamburg, with the support of VATTENFALL, in November 2008. The level 2 PSA experts from the ASAMPSA2 project partners have proposed some guidelines for the development and application of L2PSA based on their experience and on information available from international cooperation (EC Severe Accident network of Excellence - SARNET, IAEA standards, OECD-NEA publications and workshop) or open literature. The number of technical issues addressed in the guideline is very large and all are not covered with the same relevancy in the first version of the guideline. This version is submitted for external review in November 2010 by severe accident experts and PSA, especially, from SARNET and OECD-NEA members. The feedback of the external review will be dis cussed during an international open works hop planned in March 2011 and all outcomes will be taken into consideration in the final version of this guideline (June 2011). The guideline includes 3 volumes: - Volume 1 - General considerations on L2PSA. - Volume 2 - Technical recommendations for Gen II and III reactors. - Volume 3 - Specific considerations for future reactor (Gen IV). The recommendations formulated in the guideline should not be considered as 'mandatory' but should help the L2PSA developers to achieve high quality studies with limited time and resources. It may also help the L2PSA reviewers by positioning one specific study in comparison with some

Benchmarking of nuclear reactors selected in the frame of GIF project

International Nuclear Information System (INIS)

Azpitarte, O; Villanueva, A; Ramos, R; Ramilo, L; Alvarez, M; Yorio, D; Herrero, V

2012-01-01

In this article a comparative assessment of the six reactor concepts selected in the frame of the Generation IV International Forum (GIF) project is presented. The assessment was carried out in the areas of Viability of the concept, Design and nuclear safety, Economics, Sustainability, Proliferation resistance, Nuclear fuel, Reprocessing, Materials and Balance of Plant, by means of qualification of chosen performance indicators (author)

Multi scale analysis of thermal-hydraulics of nuclear reactors - the neptune project

International Nuclear Information System (INIS)

Bestion, D.

2004-01-01

Full text of publication follows:The NEPTUNE project aims at building a new two-phase thermalhydraulic platform for nuclear reactor simulation. It is jointly developed by CEA-DEN and EDF-DRD and also supported by IRSN and FRAMATOME-ANP. NEPTUNE is a new generation multi-scale platform. The system scale models the whole reactor circuit with 0D, 1D and 3D modules and is generally applied with a coarse meshing including about a thousand meshes. The component scale models components like the reactor Core or Steam Generators with a finer nodalization and is generally applied with 10 4 to 10 5 meshes. Since these components contain rod bundles or tube bundles the physical modelling uses a homogenization technique with a porosity. For some specific applications it was found necessary to add a two-phase CFD tool able to zoom on a portion of the circuit where small scale phenomena are of importance for design purpose or safety issues. Here the basic equations are still averaged like in RANS approach for single phase, but the space resolution is finer than in component codes and typical application may require 10 5 to 10 7 meshes. These three scales have to be coupled in order to simulate many reactor transients where both local effects and system effects play a role. In addition, two-phase Direct Numerical Simulation Tools with Interface Tracking Techniques can be used for even smaller scale investigations for a better understanding of basic physical processes and for developing closure relations for averaged models. The main challenges of this project are here presented and some first results are presented. (authors)

MIT pebble bed reactor project

Energy Technology Data Exchange (ETDEWEB)

Kadak, Andrew C. [Massachusetts Institute of Technology, Cambridge (United States)

2007-03-15

The conceptual design of the MIT modular pebble bed reactor is described. This reactor plant is a 250 Mwth, 120 Mwe indirect cycle plant that is designed to be deployed in the near term using demonstrated helium system components. The primary system is a conventional pebble bed reactor with a dynamic central column with an outlet temperature of 900 C providing helium to an intermediate helium to helium heat exchanger (IHX). The outlet of the IHX is input to a three shaft horizontal Brayton Cycle power conversion system. The design constraint used in sizing the plant is based on a factory modularity principle which allows the plant to be assembled 'Lego' style instead of constructed piece by piece. This principle employs space frames which contain the power conversion system that permits the Lego-like modules to be shipped by truck or train to sites. This paper also describes the research that has been conducted at MIT since 1998 on fuel modeling, silver leakage from coated fuel particles, dynamic simulation, MCNP reactor physics modeling and air ingress analysis.

MIT pebble bed reactor project

International Nuclear Information System (INIS)

Kadak, Andrew C.

2007-01-01

The conceptual design of the MIT modular pebble bed reactor is described. This reactor plant is a 250 Mwth, 120 Mwe indirect cycle plant that is designed to be deployed in the near term using demonstrated helium system components. The primary system is a conventional pebble bed reactor with a dynamic central column with an outlet temperature of 900 C providing helium to an intermediate helium to helium heat exchanger (IHX). The outlet of the IHX is input to a three shaft horizontal Brayton Cycle power conversion system. The design constraint used in sizing the plant is based on a factory modularity principle which allows the plant to be assembled 'Lego' style instead of constructed piece by piece. This principle employs space frames which contain the power conversion system that permits the Lego-like modules to be shipped by truck or train to sites. This paper also describes the research that has been conducted at MIT since 1998 on fuel modeling, silver leakage from coated fuel particles, dynamic simulation, MCNP reactor physics modeling and air ingress analysis

International project on innovative nuclear reactors and fuel cycles

International Nuclear Information System (INIS)

Mourogov, V. M.; Juhn, P. E.

2003-01-01

In response to two IAEA General Conference Resolutions in September 2000, the IAEA has launched the International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO) in May 2001. As of February 2003, 12 IAEA Member States and the European Commission have become members of INPRO. In total, 19 cost-free experts have been nominated by these Member States and the European Commission to work for the INPRO project at the IAEA. Four meetings of the INPRO Steering Committee (SC), which is the decision and review body of INPRO, were held, two in 2001 and another two in 2002. The objective of INPRO, which is composed of two phases (Phase 1 and Phase 2), is to support safe, economic and proliferation resistant use of nuclear technology, in a sustainable manner, to meet the global energy needs in the next 50 years and beyond. During Phase 1, work is also subdivided in two sub phases: The currently on-going Phase 1A is focussing on the selection of criteria and development of methodologies and guidelines for the comparison of different reactor and fuel cycle concepts and approaches, taking into account the compilation and review of such concepts and approaches, and determination of user requirements in the areas of economics; environment; safety; proliferation-resistance; and cross cutting issues. The preliminary results of Phase 1A with respect to user requirements are summarized in the paper

Specific energy released in power reactors

International Nuclear Information System (INIS)

Zaritskaya, T.S.; Kiselev, G.V.; Rudik, A.P.; Tsenter, Eh.M.

1986-01-01

Technique of determination are described and analysis of specific energy for different methods of critically maintance of RBMK and WWER-440 reactors are conducted. Characteristics of the optimal mode of critically maintanance are determined

Assessment of Westinghouse Hanford Company methods for estimating radionuclide release from ground disposal of waste water at the N Reactor sites

International Nuclear Information System (INIS)

1988-09-01

This report summarizes the results of an independent assessment by Golder Associates, Inc. of the methods used by Westinghouse Hanford Company (Westinghouse Hanford) and its predecessors to estimate the annual offsite release of radionuclides from ground disposal of cooling and other process waters from the N Reactor at the Hanford Site. This assessment was performed by evaluating the present and past disposal practices and radionuclide migration data within the context of the hydrology, geology, and physical layout of the N Reactor disposal site. The conclusions and recommendations are based upon the available data and simple analytical calculations. Recommendations are provided for conducting more refined analyses and for continued field data collection in support of estimating annual offsite releases. Recommendations are also provided for simple operational and structural measures that should reduce the quantities of radionuclides leaving the site. 5 refs., 9 figs., 1 tab

Fission-product release during accidents

International Nuclear Information System (INIS)

Hunt, C.E.L.; Cox, D.S.

1991-09-01

One of the aims when managing a reactor accident is to minimize the release of radioactive fission products. Release is dependent not only on the temperature, but also on the partial pressure of oxygen. Strongly oxidizing atmospheres, such as those that occurred during the Chernobyl accident, released semi-volatile elements like ruthenium, which has volatile oxides. At low temperatures, UO 2 oxidization to U 3 O 8 can result in extensive breakup of the fuel, resulting in the release of non-volatile fission products as aerosols. Under less oxidizing conditions, when hydrogen accumulates from the zirconium-water reaction, the resulting low oxygen partial pressure can significantly reduce these reactions. At TMI-2, only the noble gases and volatile fission products were released in significant quantities. A knowledge of the effect of atmosphere as well as temperature on the release of fission products from damaged reactor cores is therefore a useful, if not necessary, component of information required for accident management

Problems related with the power regulation of reactors by physico-chemical methods, and the behaviour of water and heavy water in nuclear reactors; Comportement de l'eau et de l'eau lourde dans les reacteurs nucleaires et problemes de la regulation de puissance par voie physico-chimique

Energy Technology Data Exchange (ETDEWEB)

Dolle, L; Conan, D; Dirian, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-07-01

Experience of the CEA heavy water reactors and a systematic study of the radiolytic decomposition of water in the core of swimming-pool reactors are described. Setting up of reactivity control by physico-chemical methods. Reactivity control by homogeneous poisoning of the reactor A comparison of the evolution of xenon poisoning with the residual anti reactivity of the poison in solution during its nuclear consumption establishes the programme which must govern the variation in its concentration if the exact compensation is to be produced The behaviour of the poison towards the reactor materials under the particular operational conditions must be taken into account. Radiolytic decomposition of water in the reactors in the presence of soluble poisons: A study of the effect of certain chemically inert salts, present in small concentrations in the water, on its radiolytic decomposition rate, has led to some new results which are discussed. The choice of a soluble poison is justified on the basis of the above results. Reactivity control by the use of a gaseous absorbent The use of a gas control rod circuit for compensation purposes, in place of solid control rods is described. The use of soluble poisons in the moderator to compensate the xenon effect, and of a gaseous absorbent in a circuit known as a gas control rod form original aspects of the reactivity control in the reactor EL 4. (authors) [French] L'observation du comportement de l'eau et de l'eau lourde dans les reacteurs en exploitation, contribue au fonctionnement sur de ceux-ci et oriente certaines etudes relatives aux techniques de controle de la reactivite par mise en oeuvre de poisons solubles. L'utilisation de poisons nucleaires dissous dans l'eau du reacteur entraine une pollution chimique de celle-ci. Les conditions d'emploi permettant d'eviter les effets indesirables de cette pollution sont etudiees. Les problemes analytiques - bien qu'importants - ne sont pas abordes dans le cadre de la communication

Technology Transfer Programme In Reactor Digital Instrumentation And Control System (REDICS) Project: Knowledge, Experiences And Future Expectations

International Nuclear Information System (INIS)

Nurfarhana Ayuni Joha; Mohamad Puad Abu; Izhar Abu Hussin; Ridzuan Abdul Mutalib; Zareen Khan Abdul Jalil Khan; Mohd Khairulezwan Abdul Manan; Mohd Sabri Minhat; Mohd Idris Taib

2013-01-01

The PUSPATI TRIGA MARK II research reactor in Malaysia was commissioned in 1982. After 31 years of operation, Nuclear Malaysia is taking an approach for a better research and development in nuclear radiations as well as the technical services that provided. Reactor TRIGA PUSPATI (RTP) is currently upgrading its control console from analogue to digital system. The Reactor Digital Instrumentation and Control System (ReDICS) project is done on cooperation with Korea Atomic Energy Research Institute (KAERI), Korea including the technical part from the design stage until commissioning as well as the Technology Transfer Program (TTP). TTP in this ReDICS project is a part of Human Resource and System Development Program. It was carried out from the design stage until the commissioning of the system. It covers all subjects related to the design on the digital system and the requirements for the operation of RTP. The objective of this paper is to share the knowledge and experiences gained through this ReDICS project. This paper will also discuss the future expectations from this ReDICS project for Nuclear Malaysia and its personnel, as well as to the country. (author)

GRSIS program to predict fission gas release and swelling behavior of metallic fast reactor fuel

International Nuclear Information System (INIS)

Lee, Chan Bock; Lee, Byung Ho; Nam, Cheol; Sohn, Dong Seong

1999-03-01

A mechanistic model of fission gas release and swelling for the U-(Pu)-Zr metallic fuel in the fast reactor, GRSIS (Gas Release and Swelling in ISotropic fuel matrix) was developed. Fission gas bubbles are assumed to nucleate isotropically from the gas atoms in the metallic fuel matrix since they can nucleate at both the grain boundaries and the phase boundaries which are randomly distributed inside the grain. Bubbles can grow to larger size by gas diffusion and coalition with other bubbles so that they are classified as three classes depending upon their sizes. When bubble swelling reaches the threshold value, bubbles become interconnected each other to make the open channel to the external free space, that is, the open bubbles and then fission gases inside the interconnected open bubbles are released instantaneously. During the irradiation, fission gases are released through the open bubbles. GRSIS model can take into account the fuel gap closure by fuel bubble swelling. When the fuel gap is closed by fuel swelling, the contact pressure between fuel and cladding in relation to the bubble swelling and temperature is calculated. GRSIS model was validated by comparison with the irradiation test results of U-(Pu)-Zr fuels in ANL as well as the parametric studies of the key variable in the model. (author). 13 refs., 1 tab., 22 figs

GRSIS program to predict fission gas release and swelling behavior of metallic fast reactor fuel

Energy Technology Data Exchange (ETDEWEB)

Lee, Chan Bock; Lee, Byung Ho; Nam, Cheol; Sohn, Dong Seong

1999-03-01

A mechanistic model of fission gas release and swelling for the U-(Pu)-Zr metallic fuel in the fast reactor, GRSIS (Gas Release and Swelling in ISotropic fuel matrix) was developed. Fission gas bubbles are assumed to nucleate isotropically from the gas atoms in the metallic fuel matrix since they can nucleate at both the grain boundaries and the phase boundaries which are randomly distributed inside the grain. Bubbles can grow to larger size by gas diffusion and coalition with other bubbles so that they are classified as three classes depending upon their sizes. When bubble swelling reaches the threshold value, bubbles become interconnected each other to make the open channel to the external free space, that is, the open bubbles and then fission gases inside the interconnected open bubbles are released instantaneously. During the irradiation, fission gases are released through the open bubbles. GRSIS model can take into account the fuel gap closure by fuel bubble swelling. When the fuel gap is closed by fuel swelling, the contact pressure between fuel and cladding in relation to the bubble swelling and temperature is calculated. GRSIS model was validated by comparison with the irradiation test results of U-(Pu)-Zr fuels in ANL as well as the parametric studies of the key variable in the model. (author). 13 refs., 1 tab., 22 figs.

Assessment of models for steam release from concrete and implications for modeling corium behavior in reactor cavities

International Nuclear Information System (INIS)

Washington, K.E.; Carroll, D.E.

1988-01-01

Models for concrete outgassing have been developed and incorporated into a developmental version of the CONTAIN code for the assessment of corium behavior in reactor cavities. The resultant code, referred to as CONTAIN/OR in order to distinguish it from the released version of CONTAIN, has the capability to model transient heat conduction and concrete outgassing in core-concrete interaction problems. This study focused on validation and assessment of the outgassing model through comparisons with other concrete response codes. In general, the model is not mechanistic; however, there are certain important processes and feedback effects that are treated rigorously. The CONTAIN outgassing model was compared against two mechanistic concrete response codes (USINT and SLAM). Gas release and temperature profile predictions for several concrete thicknesses and heating rates were performed with acceptable agreement seen in each case. The model was also applied to predict corium behavior in a reactor cavity for a hypothetical severe accident scenario. In this calculation, gases evolving from the concrete during nonablating periods fueled exothermic Zr chemical reactions in the corium. Higher corium temperatures and more concrete ablation were observed when compared with that seen when concrete outgassing was neglected. Even though this result depends somewhat upon the makeup of the corium sources and the concrete type in the cavity, it does show that concrete outgassing can be important in the modeling of corium behavior in reactor cavities. In particular, the need to expand the traditional role of CORCON from steady-state ablation to the consideration of more transient events is clearly evident as a result of this work. 5 refs., 11 figs., 1 tab

Radiological release criteria at the Fernald Environmental Management Project theory and practice

International Nuclear Information System (INIS)

Lehrter, R.W.

1995-01-01

As environmental restoration activities progress at the DOE's Fernald site, and across the country, large volumes of radioactive scrap metal (RSM) are being generated. Despite the existence of ''free-release'' guidelines from DOE. The strategy of onsite decontamination and release of RSM for unrestricted use has been generally overlooked in recent years. A pilot project was completed at Fernald in which 120 tons of RSM were decontaminated onsite and released for unrestricted use. This paper compares that strategy to more traditional DOE RSM management practices. Many options exist for managing RSM. DOE orders dictate that contractors demonstrate flexibility in utilizing a combination of techniques to optimize the benefits of waste management activates. The FERMCO Recycling Department led an effort to provide their customer with an economical alternative to the traditional approach of burying contaminated metal as LLW, based on established DOE free-release guidelines

A real-time stack radioactivity monitoring system and dose projection program

Energy Technology Data Exchange (ETDEWEB)

Hull, A.P.; Michael, P.A. [Brookhaven National Laboratory, Upton, NY (United States); Bernstein, H.J. [Bernstein & Sons, Bellport, NY (United States)

1995-02-01

At Brookhaven National Laboratory, a commercial Low- and High-Range Air Effluent Monitor has become operational at the 60 Mw (t) High Flux Beam Reactor. Its output data is combined with that from ground-level and elevated meteorological sensors to provide a real-time projection of the down-wind dose rates from noble gases and radioiodines released from the HFBR`s 100 m stack. The output of the monitor, and the meteorological sensors and the dose projections can be viewed at emergency response terminals located in the Reactor Control Room, its Technical Support Center and at the laboratory`s separately located Meteorological Station and Monitoring and Assessment Center.

Assessment of fission product release from the reactor containment building during severe core damage accidents in a PWR

International Nuclear Information System (INIS)

Fermandjian, J.; Evrard, J.M.; Generino, G.

1984-07-01

Fission product releases from the RCB associated with hypothetical core-melt accidents ABβ, S 2 CDβ and TLBβ in a PWR-900 MWe have been performed using French computer codes (in particular, the JERICHO Code for containment response analysis and AEROSOLS/B1 for aerosol behavior in the containment) related to thermalhydraulics and fission product behavior in the primary system and in the reactor containment building

Metallic fission product releases from HTR-spherical fuel elements

International Nuclear Information System (INIS)

Helmbold, M.; Amian, W.; Stoever, D.; Hecker, R.

1978-01-01

Fission product releases from fuel determines to a large extent the feasibility of a special reactor concept. Basic data describing the diffusion behaviour from coated particle fuel are presented concerning isotopes Cs 137 , Sr 90 and Agsup(110m). Taking into account these data for typical 3000MWth plants release calculations are performed. Sensitive release parameters could be defined and the results show low release figures for all the considered reactor concepts. (author)

Nuclide release from the near-field of a L/ILW repository

International Nuclear Information System (INIS)

Karlsson, L.G.; Hoeglund, L.O.; Pers, K.

1986-12-01

For Project Gewaehr 1985, the release of nuclides from a repository for low- and intermediate-level radioactive waste is calculated. The calculations are made for a reference design repository located in the marl host rock at the Oberbauen Stock reference site. The results are limited to the release of the nuclides from the waste through the engineered barriers into the surrounding host rock and will, therefore, constitute a source term for the far-field and biosphere calculations. The most probable nuclide transport mechanism is diffusion and releases are thus influenced by the nuclide diffusivities in the barriers, nuclide sorption and nuclide solubility limits. Degradation of the engineered concrete barriers is taken into account. The effects of convective flow through the barriers are described elsewhere. A near-field release model is presented. It consists of a set of computer programs suited to handel different repository designs, solubility limitations and the different waste categories. The release calculations were made for a base case in which best estimates of the parameters were used. Sensitivity to the choice of the most important parameters was tested by parameter variations. The numerical models used were checked by comparative calculations with different codes and similar data. The results of the base calculations show that near-field barriers will cause both a delay of the release to the far-field and a reduced rate of release. The sorbed nuclides, comprising the actinides and some activation and fission products, will be delayed by 10'000 years and have a maximum release rate of less than 10 -3 Ci/a each. The non-sorbed nuclides are delayed by only about 100 years and the maximum release rate is less than 10 -2 Ci per year and nuclide. The parameter variations and the design model tests gave only limited deviations from the base case results. (author)

Organization of the ITER [International Thermonuclear Experimental Reactor] Project - Sharing of information and procurements

International Nuclear Information System (INIS)

Shannon, T.E.

1990-01-01

The International Thermonuclear Experimental Reactor (ITER) project is expected to fully confirm the scientific feasibility and to address the technological feasibility of fusion power. Consequently, the machine must be designed for controlled ignition and extended burn of deuterium-tritium plasma. It must also demonstrate and perform integrated testing of components required to utilize fusion power for practical purposes. Cooperation among four countries/organizations (United States, Soviet Union, Japan, and EURATOM) to build a single experimental reactor will reduce the cost for each country and provide an international pool of scientific and engineering resources. This paper describes ITER organization for conceptual design activity, schedule for conceptual design activities, ITER operating parameters, conceptual project schedule and cost, future plans, basic principles and problems related to task sharing, and basic principles in handling of intellectual property

OECD high temperature reactor project Dragon

International Nuclear Information System (INIS)

1975-01-01

Information is presented concerning the Dragon reactor support studies and fuel irradiation programs, HTGR and fuel graphite studies, primary circuit materials, reactor safety evaluation, and administration

Direct energy conversion in fission reactors: A U.S. NERI project

International Nuclear Information System (INIS)

Slutz, Stephen A.; Seidel, David B.; Polansky, Gary F.; Rochau, Gary E.; Lipinski, Ronald J.; Besenbruch, G.; Brown, L.C.; Parish, T.A.; Anghaie, S.; Beller, D.E.

2000-01-01

In principle, the energy released by a fission can be converted directly into electricity by using the charged fission fragments. The first theoretical treatment of direct energy conversion (DEC) appeared in the literature in 1957. Experiments were conducted over the next ten years, which identified a number of problem areas. Research declined by the late 1960's due to technical challenges that limited performance. Under the Nuclear Energy Research Initiative the authors are determining if these technical challenges can be overcome with todays technology. The authors present the basic principles of DEC reactors, review previous research, discuss problem areas in detail, and identify technological developments of the last 30 years that can overcome these obstacles. As an example, the fission electric cell must be insulated to avoid electrons crossing the cell. This insulation could be provided by a magnetic field as attempted in the early experiments. However, from work on magnetically insulated ion diodes they know how to significantly improve the field geometry. Finally, a prognosis for future development of DEC reactors will be presented

Reactor building pressure proof test (PPT) and leak rate test (LRT) of Qinshan phase III (CANDU) project

International Nuclear Information System (INIS)

Gu Jun; Shi Jinqi; Fan Fuping

2004-12-01

As the first reactor building (R/B) without stainless steel liner in china, TQNPC studied the containment characteristics, such as strong concrete absorb/release air effect, poor containment penetration. etc. And carefully prepared test scheme and emergency response, creatively introduced the instrument air self-supply system in reactor building, developed the special measurement and analysis system for PPT and LRT, organized work under high-pressure on large-scale in the test. Finally got the containment leak rate result and the test-cost-time value is the best in all same type tests. (authors)

Combined development of international nuclear fusion test reactors

International Nuclear Information System (INIS)

Anon.

1987-01-01

Ambassadors of the four most important partners (Common Market, Japan, USA and USSR) in the IAEA sponsored INTOR project, met on the 15 and 16 March 1987 in Vienna under the auspices of the IAEA. A press release was issued acknowledging the considerable technical progress made in magnetic nuclear fusion research. Future design concepts, assistance in research and development work and other activities towards the provision of an international experimental thermonuclear reactor were discussed. (G.T.H.)

A brief overview of the European Fusion File (EFF) project

International Nuclear Information System (INIS)

Kellett, M.A.

2002-01-01

The European Fusion File (EFF) Project is a collaborative project with work funded by the European Fusion Development Agreement (EFDA). The emphasis is on the pooling of resources and removal of duplication of effort, leading to the efficient development of two types of nuclear data libraries for use in fusion reactor design and operation work. The two branches consist of, on the one hand, a transport file for modelling and design capabilities and, secondly, an activation file for the calculation and simulation of dose rates and energy release during operation of a future reactor. The OECD Nuclear Energy Agency's Data Bank acts as the central repository for the files and all information discussed during twice yearly meetings, which it holds, offering its services at no charge to the Project. (author)

Predicted radionuclide release from marine reactors dumped in the Kara Sea. Report of the source term working group of the international arctic seas assessment project (IASAP)

International Nuclear Information System (INIS)

1997-04-01

The present report summarizes the work carried out by the Source Term Working Group of IASAP during 1994-1996. The report is based on the studies concerning the initial and current radionuclide inventories, operational history and construction of the reactors carried out by Y. Sivintsev of the Russian Research Center ''Kurchatov Institute'', Moscow and E. Yefimov of the Institute of Physics and Power Engineering, Obninsk, Russian Federation. The working group convened five times and evaluated the results of the studies and developed models for prediction of potential releases to the environment. The calculations were carried out at the Royal Naval College, Greenwich, UK, by N. Lynn, J. Warden and S. Timms and at the Lawrence Livermore National Laboratory, California, USA, by M. Mount. 31 refs, 36 figs, 18 tabs

Small power reactor projects in the United States of America and Canada. Information gathered as a result of invitations from Member States

International Nuclear Information System (INIS)

1962-01-01

As part of its activities in connection with the development of nuclear power, and in response to the resolutions adopted by the General Conference, the Agency has been undertaking a continuing study of the technology and economics of small and medium sized power reactors, particularly with reference to the needs of the less-developed countries. This report summarizes the information gathered on the small power reactor projects in the United States of America and Canada, as a result of the opportunity afforded by these Member States to the Agency. It may be recalled that, at the third regular session of the General Conference, the United States Government offered to provide the Agency with relevant technical and economic data on several small power reactor projects of its Atomic Energy Commission. The Agency accepted the offer and since June 1960 it has sent one or two staff members at approximately six-monthly intervals to follow the development of nine power reactor projects in the United States which represent six different reactor systems. Last year, the Agency issued a report summarizing the information obtained through their visits and study of available published literature. The present document, which should be read in conjunction with that document, brings the information up to date and provides additional information on certain phases of the projects already discussed in the last report. Three more power reactor projects are also dealt with, namely the experimental gas-cooled reactor (EGCR), the high temperature gas-cooled reactor (HTGR) and the Hallam nuclear power facility (HNPF). Early in 1962, the Canadian Government expressed its willingness to make available to the Agency relevant information on the NPD and CANDU projects. The coverage of the NPD reactor is based upon the published information supplied by AECL of Canada and the visit by one of the staff members to the NPD site. The Agency wishes to acknowledge with thanks the co-operation extended

Can gamma irradiation during radiotherapy influence the metal release process for biomedical CoCrMo and 316L alloys?

Science.gov (United States)

Wei, Zheng; Edin, Jonathan; Karlsson, Anna Emelie; Petrovic, Katarina; Soroka, Inna L; Odnevall Wallinder, Inger; Hedberg, Yolanda

2018-02-09

The extent of metal release from implant materials that are irradiated during radiotherapy may be influenced by irradiation-formed radicals. The influence of gamma irradiation, with a total dose of relevance for radiotherapy (e.g., for cancer treatments) on the extent of metal release from biomedical stainless steel AISI 316L and a cobalt-chromium alloy (CoCrMo) was investigated in physiological relevant solutions (phosphate buffered saline with and without 10 g/L bovine serum albumin) at pH 7.3. Directly after irradiation, the released amounts of metals were significantly higher for irradiated CoCrMo as compared to nonirradiated CoCrMo, resulting in an increased surface passivation (enhanced passive conditions) that hindered further release. A similar effect was observed for 316L showing lower nickel release after 1 h of initially irradiated samples as compared to nonirradiated samples. However, the effect of irradiation (total dose of 16.5 Gy) on metal release and surface oxide composition and thickness was generally small. Most metals were released initially (within seconds) upon immersion from CoCrMo but not from 316L. Albumin induced an increased amount of released metals from AISI 316L but not from CoCrMo. Albumin was not found to aggregate to any greater extent either upon gamma irradiation or in the presence of trace metal ions, as determined using different light scattering techniques. Further studies should elucidate the effect of repeated friction and fractionated low irradiation doses on the short- and long term metal release process of biomedical materials. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2018. © 2018 The Authors Journal of Biomedical Materials Research Part B: Applied Biomaterials Published by Wiley Periodicals, Inc.

Shippingport Station Decommissioning Project: Contaminated concrete removal: Topical report

International Nuclear Information System (INIS)

1989-01-01

This Topical Report is a synopsis of the removal of contaminated concrete from the Shippingport Station Decommissioning Project (SSDP). The information is provided as a part of the Technology Transfer Program to document the decontamination activities in support of site release in the decommissioning of a nuclear power reactor. 4 refs., 8 figs., 2 tabs

Shippingport Station Decommissioning Project (SSDP). A progress report

International Nuclear Information System (INIS)

Mullee, G.R.; Usher, J.M.

1986-01-01

The Shippingport Atomic Power Station was shutdown in October, 1982 by the Plant Operator, Duquesne Light Company, for decommissioning by the US Department of Energy. The planning for decommissioning was completed in September, 1983. In September, 1984 operational responsibility for the station was transferred to the DOE's Decommissioning Operations Contractor - the General Electric Company (assisted by an integrated subcontractor, MK Ferguson Company). Significant accomplishments to date include the completion of all prerequisites for decommissioning, the removal of asbestos from plant systems, loading of irradiated reactor components into the reactor vessel for shipment, the commencement of electrical deactivations and the commencement of piping/component removal. Decontamination and waste processing are progressing in support of the project schedule. The reactor vessel will be shipped as one piece on a barge for burial at Hanford, Washington. The final release of the site is scheduled for April, 1990. A technology transfer program is being utilized to disseminate information about the project

Fission product release mechanisms and groupings

International Nuclear Information System (INIS)

Iglesia, F.C.; Brito, A.C.; Liu, Y.

1995-01-01

During CANDU postulated accidents the reactor fuel is estimated to be exposed to a variety of conditions. These conditions are dynamic and, during the course of an accident, the fuel may experience a wide range of temperatures and conditions from highly oxidizing to mildly reducing environments. The exposure of the reactor fuel to these environments and temperatures may affect its stoichiometry and release performance. In this paper a review of the important fission product release mechanisms is presented, the results of three out-of-pile experimental programs are summarized, and fission product release groups, for both oxidizing and reducing conditions are proposed. (author)

Evaluation of activation detectors for the SPHINX project at the LR-0 experimental reactor

International Nuclear Information System (INIS)

Lahodova, Zdena; Viererbl, Ladislav; Novak, Evzen; Svadlenkova, Marie; Rypar, Vojtech

2008-01-01