CH4 and N2O from mechanically turned windrow and vermicomposting systems following in-vessel pre-treatment

International Nuclear Information System (INIS)

Hobson, A.M.; Frederickson, J.; Dise, N.B.

2005-01-01

Methane (CH 4 ) and nitrous oxide (N 2 O) are included in the six greenhouse gases listed in the Kyoto protocol that require emission reduction. To meet reduced emission targets, governments need to first quantify their contribution to global warming. Composting has been identified as an important source of CH 4 and N 2 O. With increasing divergence of biodegradable waste from landfill into the composting sector, it is important to quantify emissions of CH 4 and N 2 O from all forms of composting and from all stages. This study focuses on the final phase of a two stage composting process and compares the generation and emission of CH 4 and N 2 O associated with two differing composting methods: mechanically turned windrow and vermicomposting. The first stage was in-vessel pre-treatment. Source-segregated household waste was first pre-composted for seven days using an in-vessel system. The second stage of composting involved forming half of the pre-composted material into a windrow and applying half to vermicomposting beds. The duration of this stage was 85 days and CH 4 and N 2 O emissions were monitored throughout for both systems. Waste samples were regularly subjected to respirometry analysis and both processes were found to be equally effective at stabilising the organic matter content. The mechanically turned windrow system was characterised by emissions of CH 4 and to a much lesser extent N 2 O. However, the vermicomposting system emitted significant fluxes of N 2 O and only trace amounts of CH 4 . In-vessel pre-treatment removed considerable amounts of available C and N prior to the second stage of composting. This had the effect of reducing emissions of CH 4 and N 2 O from the second stage compared to emissions from fresh waste found in other studies. The characteristics of each of the two composting processes are discussed in detail. Very different mechanisms for emission of CH 4 and N 2 O are proposed for each system. For the windrow system, development

Evaluation on ecological stability and biodegradation of dyeing wastewater pre-treated by electron beam

International Nuclear Information System (INIS)

Lee, M.J.; Park, C.K.; Yoo, D.H.; Lee, J.K.; Lee, B.J.; Han, B.S.; Kim, J.K.; Kim, Y.R.

2005-01-01

Biological treatment of dye wastewater pre-treated by electron beam has been performed in order to evaluate the biodegradation and ecological stability of effluent. In the process of electron-beam treatment of wastewater there are utilized chemical transformations of pollutants induced by ionizing radiation. Partial decomposition of pollutant takes place as well as transformations of pollutant molecules that result in improving subsequent purification stages like as biological processing. Dyeing wastewater contains many kind of pollutants which are difficult to be decomposed completely by microorganisms. In this study, biodegradation with dyeing wastewater pre-treated by electron beams was observed. On the other hand, consideration on public acceptance in terms of ecological stability of biological effluent pre-treated by electron beams was given in this study. The results of laboratory investigations on biodegradation and ecological stability of effluent showed that biodegradation of dye wastewater pre-treated by electron beam was enhanced compared to unirradiated one. In the initial stage of biological oxidation regardless of different HRT, dye wastewater pre-treated by electron beam could be oxidized easily compare to without treated one. More number of survived daphnia magna could be observed in the biological effluent pre-treated by electron beam. This means that biological effluent pre-treated by electron beam can be said 'it is safe on the ecological system'

Urine pretreatment for waste water processing systems. [for space station

Science.gov (United States)

Winkler, H. E.; Verostko, C. E.; Dehner, G. F.

1983-01-01

Recovery of high quality water from urine is an essential part of life support on a Space Station to avoid costly launch and resupply penalties. Water can be effectively recovered from urine by distillation following pretreatment by a chemical agent to inhibit microorganism contamination and fix volatile ammonia constituents. This paper presents the results of laboratory investigations of several pretreatment chemicals which were tested at several concentration levels in combination with sulfuric acid in urine. The optimum pretreatment formulation was then evaluated with urine in the Hamilton Standard Thermoelectric Integrated Membrane Evaporation Subsystem (TIMES). Over 2600 hours of test time was accumulated. Results of these laboratory and system tests are presented in this paper.

Factors which influence on force of boxers` and footballers` shots on the stage of base pre-treatment

Directory of Open Access Journals (Sweden)

Nikitenko S.A.

2011-02-01

Full Text Available On the stage of base pre-treatment factors which influence on force of shots the hands of boxers and feet of footballers as a criterion of competition activity efficiency are certain. Connections are certain between force of shots by hands and feet. The objective test of the specialized sense determination of boxers` and footballers` shots is offered. It is recommended to develop maximal and explosive force of all parts of sportsman body at implementation preparatory exercises with the further transfer of physical qualities on implementation of the special exercises.

Factors affecting seawater-based pretreatment of lignocellulosic date palm residues

DEFF Research Database (Denmark)

Fang, Chuanji; Thomsen, Mette Hedegaard; Frankaer, Christian Grundahl

2017-01-01

Seawater-based pretreatment of lignocellulosic biomass is an innovative process at research stage. With respect to process optimization, factors affecting seawater-based pretreatment of lignocellulosic date palm residues were studied for the first time in this paper. Pretreatment temperature (180...... °C–210 °C), salinity of seawater (0 ppt–50 ppt), and catalysts (H2SO4, Na2CO3, and NaOH) were investigated. The results showed that pretreatment temperature exerted the largest influence on seawater-based pretreatment in terms of the enzymatic digestibility and fermentability of pretreated solids...

Pretreatment of Eucalyptus in biphasic system for furfural production and accelerated enzymatic hydrolysis.

Science.gov (United States)

Zhang, Xiudong; Bai, Yuanyuan; Cao, Xuefei; Sun, Runcang

2017-08-01

Herein, an efficient biphasic pretreatment process was developed to improve the production of furfural (FF) and glucose from Eucalyptus. The influence of formic acid and NaCl on FF production from xylose in water and various biphasic systems was investigated. Results showed that the addition of formic acid and NaCl significantly promoted the FF yield, and the biphasic system of MIBK (methyl isobutyl ketone)/water exhibited the best performance for FF production. Then the Eucalyptus was pretreated in the MIBK/water system, and a maximum FF yield of 82.0% was achieved at 180°C for 60min. Surface of the pretreated Eucalyptus became relatively rough and loose, and its crystallinity index increased obviously due to the removal of hemicelluloses and lignin. The pretreated Eucalyptus samples showed much higher enzymatic hydrolysis rates (26.2-70.7%) than the raw Eucalyptus (14.5%). Copyright © 2017 Elsevier Ltd. All rights reserved.

Profiles and drivers of antibiotic resistance genes distribution in one-stage and two-stage sludge anaerobic digestion based on microwave-H2O2 pretreatment.

Science.gov (United States)

Zhang, Junya; Liu, Jibao; Wang, Yawei; Yu, Dawei; Sui, Qianwen; Wang, Rui; Chen, Meixue; Tong, Juan; Wei, Yuansong

2017-10-01

Three anaerobic digestion (AD) processes of waste activated sludge (WAS) were established including the control (mono-WAS), one-stage AD and two-stage AD along with microwave-H 2 O 2 pre-treatment (MW-H 2 O 2 ) to investigate the profiles and drivers of antibiotic resistance genes (ARGs) distribution concerning co-selection from heavy metals, intI1 and microbial community through qPCR and high-throughput sequencing method. Results showed that MW-H 2 O 2 could reduce the absolute gene copies of all ARGs while increased the relative abundance of most ARGs. After subsequent AD, both total ARGs quantities and relative abundance were enriched while two-stage AD showed some advantages over ARGs abundance reduction. Besides, AD was more effective on the potential pathogens reduction than MW-H 2 O 2 . AD could reduce the role of intI1 on the spread of ARGs, while mantel test and procrustes analysis indicated that the variation of ARGs abundance was closely associated with the discrepancy of bacterial community. Copyright © 2017 Elsevier Ltd. All rights reserved.

Pretreatment Staging Positron Emission Tomography/Computed Tomography in Patients With Inflammatory Breast Cancer Influences Radiation Treatment Field Designs

International Nuclear Information System (INIS)

Walker, Gary V.; Niikura, Naoki; Yang Wei; Rohren, Eric; Valero, Vicente; Woodward, Wendy A.; Alvarez, Ricardo H.; Lucci, Anthony; Ueno, Naoto T.; Buchholz, Thomas A.

2012-01-01

Purpose: Positron emission tomography/computed tomography (PET/CT) is increasingly being utilized for staging of inflammatory breast cancer (IBC). The purpose of this study was to define how pretreatment PET/CT studies affected postmastectomy radiation treatment (PMRT) planning decisions for IBC. Methods and Materials: We performed a retrospective analysis of 62 patients diagnosed with IBC between 2004 and 2009, who were treated with PMRT in our institution and who had a staging PET/CT within 3 months of diagnosis. Patients received a baseline physical examination, staging mammography, ultrasonographic examination of breast and draining lymphatics, and chest radiography; most patients also had a bone scan (55 patients), liver imaging (52 patients), breast MRI (46 patients), and chest CT (25 patients). We compared how PET/CT findings affected PMRT, assuming that standard PMRT would target the chest wall, level III axilla, supraclavicular fossa, and internal mammary chain (IMC). Any modification of target volumes, field borders, or dose prescriptions was considered a change. Results: PET/CT detected new areas of disease in 27 of the 62 patients (44%). The areas of additional disease included the breast (1 patient), ipsilateral axilla (1 patient), ipsilateral supraclavicular (4 patients), ipsilateral infraclavicular (1 patient), ipsilateral IMC (5 patients), ipsilateral subpectoral (3 patients), mediastinal (8 patients), other distant/contralateral lymph nodes (15 patients), or bone (6 patients). One patient was found to have a non-breast second primary tumor. The findings of the PET/CT led to changes in PMRT in 11 of 62 patients (17.7%). These changes included additional fields in 5 patients, adjustment of fields in 2 patients, and higher doses to the supraclavicular fossa (2 patients) and IMC (5 patients). Conclusions: For patients with newly diagnosed IBC, pretreatment PET/CT provides important information concerning involvement of locoregional lymph nodes

Pretreatment prostate-specific antigen values in patients with prostate cancer: 1989 patterns of care study process survey

International Nuclear Information System (INIS)

Teshima, Teruki; Hanlon, Alexandra M.; Hanks, Gerald E.

1995-01-01

Purpose: A Patterns of Care Study (PCS) national survey was conducted to show the national averages for processes of radiation therapy care for prostate cancer patients in 1989. In the current study we report an analysis of pretreatment prostate-specific antigen (PSA) by stage, grade, and ethnic origin. Methods and Materials: Process data were collected from 672 patients treated in 1989 at 71 separate institutions. Four hundred and twenty-seven (64%) of these patients had a pretreatment PSA value recorded. Three hundred and forty-three of the 427 patients were treated with external beam irradiation alone and were selected for the current analysis. The 1992 AJCC staging system was used. Results: There was a significant increase in pretreatment PSA with increasing stage. The median values of PSA were 8.3 ngm/ml in the T1 group (n = 65), 11.2 ngm/ml in the T2 group (n = 178), and 20.9 ngm/ml in the T3 group (n = 90) (p < 0.001). Ten patients were not staged. There was a significant increase in pretreatment PSA with decreasing differentiation. The median pretreatment PSA was 9.7 ngm/ml in well-differentiated tumors (n = 109), 13.0 ngm/ml in moderately differentiated tumors (n = 163), and 22.0 ngm/ml in poorly differentiated tumors. (n = 61) (p < 0.001). Ten patients had no differentiation recorded. African Americans (24) showed a significant increase in pretreatment PSA compared to Caucasians (304). The respective medians were 23.2 ng/ml and 11.9 ng/ml (p = 0.04). They also show more poorly differentiated tumors (33% vs. 17%) and more T3 tumors (46% vs. 25%). Other minorities, although small in number (n = 9) were similar to African Americans. Conclusion: Pretreatment PSA levels were established for patients treated with external beam irradiation in 1989 in the United States. They increase with stage and decreasing differentiation. African Americans and other minorities show a doubling of median values compared to Caucasians' pretreatment PSA with an increase in stage

TWRS tank waste pretreatment process development hot test siting report

International Nuclear Information System (INIS)

Howden, G.F.; Banning, D.L.; Dodd, D.A.; Smith, D.A.; Stevens, P.F.; Hansen, R.I.; Reynolds, B.A.

1995-02-01

This report is the sixth in a series that have assessed the hot testing requirements for TWRS pretreatment process development and identified the hot testing support requirements. This report, based on the previous work, identifies specific hot test work packages, matches those packages to specific hot cell facilities, and provides recommendations of specific facilities to be employed for the pretreatment hot test work. Also identified are serious limitations in the tank waste sample retrieval and handling infrastructure. Recommendations are provided for staged development of 500 mL, 3 L, 25 L and 4000 L sample recovery systems and specific actions to provide those capabilities

Nonhazardous Urine Pretreatment Method for Future Exploration Systems, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — A nonhazardous urine pretreatment system prototype is proposed that will stabilize urine against biological growth or chemical instabilities without using hazardous...

Mainstream upflow nitritation-anammox system with hybrid anaerobic pretreatment: Long-term performance and microbial community dynamics.

Science.gov (United States)

Li, Xiaojin; Sun, Shan; Yuan, Heyang; Badgley, Brian D; He, Zhen

2017-11-15

Mainstream nitritation-anammox is of strong interest to energy- and resource-efficient domestic wastewater treatment. However, there lack in-depth studies of pretreatment, tests of actual wastewater, and examination of long-term performance. Herein, an upflow nitritation-anammox granular reactor has been investigated to treat primary effluent with a hybrid anaerobic reactor (HAR) as pretreatment for more than 300 days. This system achieved 92% of COD removal, 75% of which was accomplished by the HAR, and had an average final effluent COD concentration of 22 mg L -1 . More than 90% of ammonium was removed in the nitritation-anammox reactor, achieving a nitrogen removal rate of 81.0 g N m -3  d -1 in the last stage. The accumulation of sulfate-reducing bacteria in the HAR evidenced the effect of sulfate on COD removal and subsequent nitrogen removal. Anammox bacteria (predominantly Ca. Jettenia asiatica) accounted for up to 40.2% of total granular communities, but their abundance decreased over time in the suspended communities. The dynamics of major metabolisms and functional genes involved in nitrogen conversion were predicted by PICRUSt based on the taxonomic data, providing more insights into the functions of the microbial communities. These results have demonstrated the effectiveness and importance of anaerobic pretreatment to successful mainstream nitritation-anammox. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bioethanol production: Pretreatment and enzymatic hydrolysis of softwood

Energy Technology Data Exchange (ETDEWEB)

Tengborg, Charlotte

2000-05-01

The enzymatic hydrolysis process can be used to produce bioethanol from softwood, which are the dominating raw material in the Northern hemisphere. This thesis deals with the development of the process focusing on the pretreatment and the enzymatic hydrolysis stages. The influence of pretreatment conditions on sugar yield, and the effect of inhibitors on the ethanol yield, were investigated for spruce and pine. The maximum yields of hemicellulose sugars and glucose were obtained under different pretreatment conditions. This indicates that two-stage pretreatment may be preferable. The added catalysts, H{sub 2}SO{sub 4} and SO{sub 2}, resulted in similar total sugar yields about 40 g/100 g dry raw material. However, the fermentability of SO{sub 2}-impregnated material was better. This pretreatment resulted in the formation of inhibitors to the subsequent process steps, e.g. sugar and lignin degradation products. The glucose yield in the enzymatic hydrolysis stage was affected by various parameters such as enzyme loading, temperature, pH, residence time, substrate concentration, and agitation. To decrease the amount of fresh water used and thereby waste water produced, the sugar-rich prehydrolysate from the pretreatment step was included in the enzymatic hydrolysis of the solid fraction, resulting in a reduction in the cellulose conversion of up to 36%. Different prehydrolysate detoxification methods, such as treatment with Ca(OH){sub 2}, laccase, and fermentation using yeast, were investigated. The latter was shown to be very efficient. The amount of fresh water used can be further reduced by recycling various process streams. This was simulated experimentally in a bench-scale process. A reduction in fresh water demand of 50% was obtained without any further negative effects on either hydrolysis or fermentation.

Anaerobic co-digestion of municipal organic wastes and pre-treatment to enhance biogas production from waste.

Science.gov (United States)

Li, Chenxi; Champagne, Pascale; Anderson, Bruce C

2014-01-01

Co-digestion and pre-treatment have been recognized as effective, low-cost and commercially viable approaches to reduce anaerobic digestion process limitations and improve biogas yields. In our previous batch-scale study, fat, oil, and grease (FOG) was investigated as a suitable potential co-substrate, and thermo-chemical pre-treatment (TCPT) at pH = 10 and 55 °C improved CH4 production from FOG co-digestions. In this project, co-digestions with FOG were studied in bench-scale two-stage thermophilic semi-continuous flow co-digesters with suitable TCPT (pH = 10, 55 °C). Overall, a 25.14 ± 2.14 L/d (70.2 ± 1.4% CH4) biogas production was obtained, which was higher than in the two-stage system without pre-treatment. The results could provide valuable fundamental information to support full-scale investigations of anaerobic co-digestion of municipal organic wastes.

PROJECT W-551 DETERMINATION DATA FOR EARLY LAW INTERIM PRETREATMENT SYSTEM SELECTION

Energy Technology Data Exchange (ETDEWEB)

TEDESCHI AR

2008-08-11

This report provides the detailed assessment forms and data for selection of the solids separation and cesium separation technology for project W-551, Interim Pretreatment System. This project will provide early pretreated low activity waste feed to the Waste Treatment Plant to allow Waste Treatment Plan Low Activity Waste facility operation prior to construction completion of the Pretreatment and High Level Waste facilities. The candidate solids separations technologies are rotary microfiltration and crossflow filtration, and the candidate cesium separation technologies are fractional crystallization, caustic-side solvent extraction, and ion-exchange using spherical resorcinol-formaldehyde resin. This data was used to prepare a cross-cutting technology summary, reported in RPP-RPT-37740.

Stage T1-2 prostate cancer with pretreatment PSA 10 ng/ml or less: radiotherapy or surgery?

International Nuclear Information System (INIS)

Keyser, Douglas; Kupelian, Patrick; Zippe, Craig; Klein, Eric

1996-01-01

Purpose: Presently, patients with pretreatment PSA levels ≤10 ng/ml constitute the majority of cases presenting for definitive treatment. Our aim was to determine whether the type of treatment (radiotherapy versus surgery) affected biochemical failure rates in this group of patients. This study is based on 389 patients treated at a single institution. Material and Methods: The charts of all patients treated with either radiotherapy or prostatectomy alone between 1987 and 1993 were reviewed (n=811). Patients with clinical stage T1 or T2 disease, and a pretreatment PSA level (iPSA) of 10.0 or less were analyzed (n=389). Two hundred forty nine (64%) received radical prostatectomy and 140 (36%) received radiotherapy (median dose 66.6 Gy). Pretreatment patient characteristics including clinical stage, biopsy Gleason score (GS) and iPSA level were not significantly different between the radiation and surgery groups (Table 1). The patients treated with radiation were significantly older (median age 70 years vs. 64 years, p<0.05). A total of 37% of the prostatectomy patients had a positive margin. The median follow-up time was 33 months; 1458 follow-up PSA levels were available for analysis. Biochemical failure was defined as a rise in PSA level of 1.0 ng/ml above the nadir PSA level in radiotherapy cases, or any value above 0.2 ng/ml in the prostatectomy cases. Results: The overall 5 year actuarial biochemical relapse free survival (bRFS) rate was 70%. The 5-year bRFS rates for prostatectomy and radiotherapy were identical (70%) (Fig.1). The significant factors affecting bRFS rates were iPSA level (≤4 vs. 4-10 ng/ml) and Gleason score (≤6 vs. ≥7) (Table 2). The 5-year bRFS rates of patients with iPSA ≤4 vs. iPSA 4-10 ng/ml were 92% vs. 61% respectively, p<0.01. The 5-year clinical relapse free survival was 93%. All clinical failures were preceded by biochemical failure. Patients with positive surgical margins did significantly worse than those with negative

Prognostic Value and Reproducibility of Pretreatment CT Texture Features in Stage III Non-Small Cell Lung Cancer

Energy Technology Data Exchange (ETDEWEB)

Fried, David V. [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Graduate School of Biomedical Sciences, The University of Texas Health Science Center at Houston, Houston, Texas (United States); Tucker, Susan L. [Department of Bioinformatics and Computational Biology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Zhou, Shouhao [Division of Quantitative Sciences, Department of Bioinformatics and Computational Biology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Liao, Zhongxing [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Mawlawi, Osama [Graduate School of Biomedical Sciences, The University of Texas Health Science Center at Houston, Houston, Texas (United States); Ibbott, Geoffrey [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Graduate School of Biomedical Sciences, The University of Texas Health Science Center at Houston, Houston, Texas (United States); Court, Laurence E., E-mail: LECourt@mdanderson.org [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Graduate School of Biomedical Sciences, The University of Texas Health Science Center at Houston, Houston, Texas (United States)

2014-11-15

Purpose: To determine whether pretreatment CT texture features can improve patient risk stratification beyond conventional prognostic factors (CPFs) in stage III non-small cell lung cancer (NSCLC). Methods and Materials: We retrospectively reviewed 91 cases with stage III NSCLC treated with definitive chemoradiation therapy. All patients underwent pretreatment diagnostic contrast enhanced computed tomography (CE-CT) followed by 4-dimensional CT (4D-CT) for treatment simulation. We used the average-CT and expiratory (T50-CT) images from the 4D-CT along with the CE-CT for texture extraction. Histogram, gradient, co-occurrence, gray tone difference, and filtration-based techniques were used for texture feature extraction. Penalized Cox regression implementing cross-validation was used for covariate selection and modeling. Models incorporating texture features from the 33 image types and CPFs were compared to those with models incorporating CPFs alone for overall survival (OS), local-regional control (LRC), and freedom from distant metastases (FFDM). Predictive Kaplan-Meier curves were generated using leave-one-out cross-validation. Patients were stratified based on whether their predicted outcome was above or below the median. Reproducibility of texture features was evaluated using test-retest scans from independent patients and quantified using concordance correlation coefficients (CCC). We compared models incorporating the reproducibility seen on test-retest scans to our original models and determined the classification reproducibility. Results: Models incorporating both texture features and CPFs demonstrated a significant improvement in risk stratification compared to models using CPFs alone for OS (P=.046), LRC (P=.01), and FFDM (P=.005). The average CCCs were 0.89, 0.91, and 0.67 for texture features extracted from the average-CT, T50-CT, and CE-CT, respectively. Incorporating reproducibility within our models yielded 80.4% (±3.7% SD), 78.3% (±4.0% SD), and 78

Prognostic Value and Reproducibility of Pretreatment CT Texture Features in Stage III Non-Small Cell Lung Cancer

International Nuclear Information System (INIS)

Fried, David V.; Tucker, Susan L.; Zhou, Shouhao; Liao, Zhongxing; Mawlawi, Osama; Ibbott, Geoffrey; Court, Laurence E.

2014-01-01

Purpose: To determine whether pretreatment CT texture features can improve patient risk stratification beyond conventional prognostic factors (CPFs) in stage III non-small cell lung cancer (NSCLC). Methods and Materials: We retrospectively reviewed 91 cases with stage III NSCLC treated with definitive chemoradiation therapy. All patients underwent pretreatment diagnostic contrast enhanced computed tomography (CE-CT) followed by 4-dimensional CT (4D-CT) for treatment simulation. We used the average-CT and expiratory (T50-CT) images from the 4D-CT along with the CE-CT for texture extraction. Histogram, gradient, co-occurrence, gray tone difference, and filtration-based techniques were used for texture feature extraction. Penalized Cox regression implementing cross-validation was used for covariate selection and modeling. Models incorporating texture features from the 33 image types and CPFs were compared to those with models incorporating CPFs alone for overall survival (OS), local-regional control (LRC), and freedom from distant metastases (FFDM). Predictive Kaplan-Meier curves were generated using leave-one-out cross-validation. Patients were stratified based on whether their predicted outcome was above or below the median. Reproducibility of texture features was evaluated using test-retest scans from independent patients and quantified using concordance correlation coefficients (CCC). We compared models incorporating the reproducibility seen on test-retest scans to our original models and determined the classification reproducibility. Results: Models incorporating both texture features and CPFs demonstrated a significant improvement in risk stratification compared to models using CPFs alone for OS (P=.046), LRC (P=.01), and FFDM (P=.005). The average CCCs were 0.89, 0.91, and 0.67 for texture features extracted from the average-CT, T50-CT, and CE-CT, respectively. Incorporating reproducibility within our models yielded 80.4% (±3.7% SD), 78.3% (±4.0% SD), and 78

Microalgal biomass pretreatment for bioethanol production: a review

Directory of Open Access Journals (Sweden)

Jesús Velazquez-Lucio

2018-03-01

Full Text Available Biofuels derived from microalgae biomass have received a great deal of attention owing to their high potentials as sustainable alternatives to fossil fuels. Microalgae have a high capacity of CO2 fixation and depending on their growth conditions, they can accumulate different quantities of lipids, proteins, and carbohydrates. Microalgal biomass can, therefore, represent a rich source of fermentable sugars for third generation bioethanol production. The utilization of microalgal carbohydrates for bioethanol production follows three main stages: i pretreatment, ii saccharification, and iii fermentation. One of the most important stages is the pretreatment, which is carried out to increase the accessibility to intracellular sugars, and thus plays an important role in improving the overall efficiency of the bioethanol production process. Diverse types of pretreatments are currently used including chemical, thermal, mechanical, biological, and their combinations, which can promote cell disruption, facilitate extraction, and result in the modification the structure of carbohydrates as well as the production of fermentable sugars. In this review, the different pretreatments used on microalgae biomass for bioethanol production are presented and discussed. Moreover, the methods used for starch and total carbohydrates quantification in microalgae biomass are also briefly presented and compared.

Drivers of microbial community composition in mesophilic and thermophilic temperature-phased anaerobic digestion pre-treatment reactors.

Science.gov (United States)

Pervin, Hasina M; Dennis, Paul G; Lim, Hui J; Tyson, Gene W; Batstone, Damien J; Bond, Philip L

2013-12-01

Temperature-phased anaerobic digestion (TPAD) is an emerging technology that facilitates improved performance and pathogen destruction in anaerobic sewage sludge digestion by optimising conditions for 1) hydrolytic and acidogenic organisms in a first-stage/pre-treatment reactor and then 2) methogenic populations in a second stage reactor. Pre-treatment reactors are typically operated at 55-65 °C and as such select for thermophilic bacterial communities. However, details of key microbial populations in hydrolytic communities and links to functionality are very limited. In this study, experimental thermophilic pre-treatment (TP) and control mesophilic pre-treatment (MP) reactors were operated as first-stages of TPAD systems treating activated sludge for 340 days. The TP system was operated sequentially at 50, 60 and 65 °C, while the MP rector was held at 35 °C for the entire period. The composition of microbial communities associated with the MP and TP pre-treatment reactors was characterised weekly using terminal-restriction fragment length polymorphism (T-RFLP) supported by clone library sequencing of 16S rRNA gene amplicons. The outcomes of this approach were confirmed using 454 pyrosequencing of gene amplicons and fluorescence in-situ hybridisation (FISH). TP associated bacterial communities were dominated by populations affiliated to the Firmicutes, Thermotogae, Proteobacteria and Chloroflexi. In particular there was a progression from Thermotogae to Lutispora and Coprothermobacter and diversity decreased as temperature and hydrolysis performance increased. While change in the composition of TP associated bacterial communities was attributable to temperature, that of MP associated bacterial communities was related to the composition of the incoming feed. This study determined processes driving the dynamics of key microbial populations that are correlated with an enhanced hydrolytic functionality of the TPAD system. Copyright © 2013 Elsevier Ltd. All rights

Methods for pretreating biomass

Science.gov (United States)

Balan, Venkatesh; Dale, Bruce E; Chundawat, Shishir; Sousa, Leonardo

2017-05-09

A method for pretreating biomass is provided, which includes, in a reactor, allowing gaseous ammonia to condense on the biomass and react with water present in the biomass to produce pretreated biomass, wherein reactivity of polysaccharides in the biomass is increased during subsequent biological conversion as compared to the reactivity of polysaccharides in biomass which has not been pretreated. A method for pretreating biomass with a liquid ammonia and recovering the liquid ammonia is also provided. Related systems which include a biochemical or biofuel production facility are also disclosed.

Modelling of Two-Stage Methane Digestion With Pretreatment of Biomass

Science.gov (United States)

Dychko, A.; Remez, N.; Opolinskyi, I.; Kraychuk, S.; Ostapchuk, N.; Yevtieieva, L.

2018-04-01

Systems of anaerobic digestion should be used for processing of organic waste. Managing the process of anaerobic recycling of organic waste requires reliable predicting of biogas production. Development of mathematical model of process of organic waste digestion allows determining the rate of biogas output at the two-stage process of anaerobic digestion considering the first stage. Verification of Konto's model, based on the studied anaerobic processing of organic waste, is implemented. The dependencies of biogas output and its rate from time are set and may be used to predict the process of anaerobic processing of organic waste.

PROJECT W-551 INTERIM PRETREATMENT SYSTEM TECHNOLOGY SELECTION SUMMARY DECISION REPORT AND RECOMMENDATION

International Nuclear Information System (INIS)

CONRAD EA

2008-01-01

This report provides the conclusions of the tank farm interim pretreatment technology decision process. It documents the methodology, data, and results of the selection of cross-flow filtration and ion exchange technologies for implementation in project W-551, Interim Pretreatment System. This selection resulted from the evaluation of specific scope criteria using quantitative and qualitative analyses, group workshops, and technical expert personnel

EFFECT OF AQUEOUS PRETREATMENT ON PYROLYSIS CHARACTERISTICS OF NAPIER GRASS

Directory of Open Access Journals (Sweden)

ISAH YAKUB MOHAMMED

2015-11-01

Full Text Available Effect of non-catalytic aqueous pretretment on pyrolysis characteristics of Napier grass was investigated using thermogravimetric analyser. Increasing pretreatment severity (0.0-2.0 improved pyrolysis process. The residual mass at the end of pyrolysis for the pretreated sample was about 50% less compared to the untreated sample. Kinetics of the process was evaluated using order based model and both pretreated and untreated samples followed first order reaction. The activation energy of the pretreated samples was similar and higher than that of the raw sample which was attributed to faster rate of decomposition due removal of hetromaterials (ash, extractives and some hemicellulose in the pretreatment stage. Finally, this pretreatment method has demonstrated effectiveness for the removal of pyrolysis retardants and will improve the quantity and quality of bio-oil yield.

Increasing Water System Efficiency with Ultrafiltration Pre-treatment in Power Plants

International Nuclear Information System (INIS)

Majamaa, Katariina; Suarez, Javier; Gasia Eduard

2012-09-01

Water demineralization with reverse osmosis (RO) membranes has a long and successful history in water treatment for power plants. As the industry strives for more efficient, reliable and compact water systems, pressurized hollow-fiber ultrafiltration (UF) has become an increasingly appealing pre-treatment technology. Compared to conventional, non- membrane based pretreatments, ultrafiltration offers higher efficiency in the removal of suspended solids, microorganisms and colloidal matter, which are all common causes for operational challenges experienced in the RO systems. In addition, UF is more capable of handling varying feed water qualities and removes the risk of particle carry-over often seen with conventional filtration techniques. Ultrafiltration is a suitable treatment technology for various water types from surface waters to wastewater, and the more fluctuating or challenging the feed water source is, the better the benefits of UF are seen compared to conventional pretreatments. Regardless of the feed water type, ultrafiltration sustains a constant supply of high quality feed water to downstream RO, allowing a more compact and cost efficient RO system design with improved operational reliability. A detailed focus on the design and operational aspects and experiences of two plants is provided. These examples demonstrate both economical UF operation and tangible impact of RO process improvement. Experience from these plants can be leveraged to new projects. (authors)

Comparison and Optimization of Saccharification Conditions of Alkaline Pre-Treated Triticale Straw for Acid and Enzymatic Hydrolysis Followed by Ethanol Fermentation

Directory of Open Access Journals (Sweden)

Rafał Łukajtis

2018-03-01

Full Text Available This paper concerns the comparison of the efficiency of two-stage hydrolysis processes, i.e., alkaline pre-treatment and acid hydrolysis, as well as alkaline pre-treatment followed by enzymatic hydrolysis, carried out in order to obtain reducing sugars from triticale straw. For each of the analyzed systems, the optimization of the processing conditions was carried out with respect to the glucose yield. For the alkaline pre-treatment, an optimal catalyst concentration was selected for constant values of temperature and pre-treatment time. For enzymatic hydrolysis, optimal process time and concentration of the enzyme preparation were determined. For the acidic hydrolysis, performed with 85% phosphoric acid, the optimum temperature and hydrolysis time were determined. In the hydrolysates obtained after the two-stage treatment, the concentration of reducing sugars was determined using HPLC. The obtained hydrolysates were subjected to ethanol fermentation. The concentrations of fermentation inhibitors are given and their effects on the alcoholic fermentation efficiency are discussed.

Fermentation of undetoxified sugarcane bagasse hydrolyzates using a two stage hydrothermal and mechanical refining pretreatment

Science.gov (United States)

Economical and environmentally friendly pretreatment technologies are required for commercial conversion of lignocellulosic feedstocks to fermentable sugars for fermentation to biofuels. In this paper, a novel pretreatment technology was developed for conversion of sugarcane bagasse into ethanol usi...

Caustic-Side Solvent-Extraction Modeling for Hanford Interim Pretreatment System

International Nuclear Information System (INIS)

Moyer, B.A.; Birdwell, J.F.; Delmau, L. H.; McFarlane, J.

2008-01-01

The purpose of this work is to examine the applicability of the Caustic-Side Solvent Extraction (CSSX) process for the removal of cesium from Hanford tank-waste supernatant solutions in support of the Hanford Interim Pretreatment System (IPS). The Hanford waste types are more challenging than those at the Savannah River Site (SRS) in that they contain significantly higher levels of potassium, the chief competing ion in the extraction of cesium. It was confirmed by use of the CSSX model that the higher levels of potassium depress the cesium distribution ratio (DCs), as validated by measurement of DCs values for four of eight specified Hanford waste-simulant compositions. The model predictions were good to an apparent standard error of ±11%. It is concluded from batch distribution experiments, physical-property measurements, equilibrium modeling, flowsheet calculations, and contactor sizing that the CSSX process as currently employed for cesium removal from alkaline salt waste at the SRS is capable of treating similar Hanford tank feeds. For the most challenging waste composition, 41 stages would be required to provide a cesium decontamination factor (DF) of 5000 and a concentration factor (CF) of 5. Commercial contacting equipment with rotor diameters of 10 in. for extraction and 5 in. for stripping should have the capacity to meet throughput requirements, but testing will be required to confirm that the needed efficiency and hydraulic performance are actually obtainable. Markedly improved flowsheet performance was calculated for a new solvent formulation employing the more soluble cesium extractant BEHBCalixC6 used with alternative scrub and strip solutions, respectively 0.1 M NaOH and 10 mM boric acid. The improved system can meet minimum requirements (DF = 5000 and CF = 5) with 17 stages or more ambitious goals (DF = 40,000 and CF = 15) with 19 stages. Potential benefits of further research and development are identified that would lead to reduced costs, greater

Frequent hemodialysis with NxStage system in pediatric patients receiving maintenance hemodialysis.

Science.gov (United States)

Goldstein, Stuart L; Silverstein, Douglas M; Leung, Jocelyn C; Feig, Daniel I; Soletsky, Beth; Knight, Cathy; Warady, Bradley A

2008-01-01

Recent evidence from adult hemodialysis (HD) patient studies reveal improved biochemical control and reported health-related quality of life after transition from conventional thrice weekly to daily home maintenance HD treatment. Published pediatric frequent dialysis experiences demonstrate similar improvement but all used conventional HD machines, which employ a treated municipal water supply, thereby frequently exposing patients to proinflammatory components. We report our pediatric experience with six-times-weekly HD using the NxStage system, which uses sterile dialysis fluid to provide dialysis in the home or center setting. Four patients (weight range 38-61.4 kg) completed the 16-week study. Patients exhibited progressive reductions in casual pretreatment systolic and diastolic blood pressures, discontinuation of antihypertensive medications, and decreased blood pressure load by ambulatory blood pressure monitoring. Mean serum phosphorus improved without change in phosphorus binder medication, and all three patients with a normalized protein catabolic rate 1.1 g/kg per day. Patients reported no adverse effects. Variable changes in proinflammatory cytokine levels were observed. We suggest that frequent HD with the NxStage system be considered for children who would benefit from home-based maintenance dialysis.

Does residual H2O2 result in inhibitory effect on enhanced anaerobic digestion of sludge pretreated by microwave-H2O2 pretreatment process?

Science.gov (United States)

Liu, Jibao; Jia, Ruilai; Wang, Yawei; Wei, Yuansong; Zhang, Junya; Wang, Rui; Cai, Xing

2017-04-01

This study investigated the effects of residual H 2 O 2 on hydrolysis-acidification and methanogenesis stages of anaerobic digestion after microwave-H 2 O 2 (MW-H 2 O 2 ) pretreatment of waste activated sludge (WAS). Results showed that high sludge solubilization at 35-45 % was achieved after pretreatment, while large amounts of residual H 2 O 2 remained and refractory compounds were thus generated with high dosage of H 2 O 2 (0.6 g H 2 O 2 /g total solids (TS), 1.0 g H 2 O 2 /g TS) pretreatment. The residual H 2 O 2 not only inhibited hydrolysis-acidification stage mildly, such as hydrolase activity, but also had acute toxic effect on methanogens, resulting in long lag phase, low methane yield rate, and no increase of cumulative methane production during the 30-day BMP tests. When the low dosage of H 2 O 2 at 0.2 g H 2 O 2 /g TS was used in MW-H 2 O 2 pretreatment, sludge anaerobic digestion was significantly enhanced. The cumulative methane production increased by 29.02 %, but still with a lag phase of 1.0 day. With removing the residual H 2 O 2 by catalase, the initial lag phase of hydrolysis-acidification stage decreased from 1.0 to 0.5 day.

A stage is a stage is a stage: a direct comparison of two scoring systems.

Science.gov (United States)

Dawson, Theo L

2003-09-01

L. Kohlberg (1969) argued that his moral stages captured a developmental sequence specific to the moral domain. To explore that contention, the author compared stage assignments obtained with the Standard Issue Scoring System (A. Colby & L. Kohlberg, 1987a, 1987b) and those obtained with a generalized content-independent stage-scoring system called the Hierarchical Complexity Scoring System (T. L. Dawson, 2002a), on 637 moral judgment interviews (participants' ages ranged from 5 to 86 years). The correlation between stage scores produced with the 2 systems was .88. Although standard issue scoring and hierarchical complexity scoring often awarded different scores up to Kohlberg's Moral Stage 2/3, from his Moral Stage 3 onward, scores awarded with the two systems predominantly agreed. The author explores the implications for developmental research.

Temperature Modelling of the Biomass Pretreatment Process

DEFF Research Database (Denmark)

Prunescu, Remus Mihail; Blanke, Mogens; Jensen, Jakob M.

2012-01-01

In a second generation biorefinery, the biomass pretreatment stage has an important contribution to the efficiency of the downstream processing units involved in biofuel production. Most of the pretreatment process occurs in a large pressurized thermal reactor that presents an irregular temperature...... that captures the environmental temperature differences inside the reactor using distributed parameters. A Kalman filter is then added to account for any missing dynamics and the overall model is embedded into a temperature soft sensor. The operator of the plant will be able to observe the temperature in any...

The Plasmodium PI(4)K inhibitor KDU691 selectively inhibits dihydroartemisinin-pretreated Plasmodium falciparum ring-stage parasites.

Science.gov (United States)

Dembele, L; Ang, X; Chavchich, M; Bonamy, G M C; Selva, J J; Lim, M Yi-Xiu; Bodenreider, C; Yeung, B K S; Nosten, F; Russell, B M; Edstein, M D; Straimer, J; Fidock, D A; Diagana, T T; Bifani, P

2017-05-24

Malaria control and elimination are threatened by the emergence and spread of resistance to artemisinin-based combination therapies (ACTs). Experimental evidence suggests that when an artemisinin (ART)-sensitive (K13 wild-type) Plasmodium falciparum strain is exposed to ART derivatives such as dihydroartemisinin (DHA), a small population of the early ring-stage parasites can survive drug treatment by entering cell cycle arrest or dormancy. After drug removal, these parasites can resume growth. Dormancy has been hypothesized to be an adaptive physiological mechanism that has been linked to recrudescence of parasites after monotherapy with ART and, possibly contributes to ART resistance. Here, we evaluate the in vitro drug sensitivity profile of normally-developing P. falciparum ring stages and DHA-pretreated dormant rings (DP-rings) using a panel of antimalarial drugs, including the Plasmodium phosphatidylinositol-4-OH kinase (PI4K)-specific inhibitor KDU691. We report that while KDU691 shows no activity against rings, it is highly inhibitory against DP-rings; a drug effect opposite to that of ART. Moreover, we provide evidence that KDU691 also kills DP-rings of P. falciparum ART-resistant strains expressing mutant K13.

Two-stage pretreatment of excess sludge for electricity generation in microbial fuel cell.

Science.gov (United States)

Zhang, Yi; Zhao, Yang-Guo; Guo, Liang; Gao, Mengchun

2018-01-12

Thermophiles hydrolysis and acidogens fermentation were sequentially adopted to pretreat excess sludge for microbial fuel cell (MFC) electricity production. The results indicated that MFC fed with the thermophiles-acidogens pretreated sludge (MFC AB), reached a higher removal of ammonia nitrogen than the MFC fed with the heating hydrolysis and acidogens fermentation pretreated sludge (MFC NB). However, compared with the MFC AB, MFC NB presented a better performance for removal of soluble chemical oxygen demand (SCOD) (90.08%) and protein (82.42%). As for the electricity production, MFC NB obtained higher voltage of 0.632 V and maximum power density with 1.05 W/m 3 while MFC AB reached maximum voltage of 0.373 V and maximum power density of 0.58 W/m 3 . Bacterial 16S rRNA-based molecular microbial techniques showed that microbial communities on both MFC anode biofilms was diverse and different. The cooperation of fermentation bacteria and electricigen Shewanella baltica in the MFC NB may have contributed towards the improvement of electricity generation.

Pre-treating dentin with chlorhexadine and CPP-ACP: self-etching and universal adhesive systems.

Science.gov (United States)

Dos Santos, Ricardo Alves; de Lima, Eliane Alves; Montes, Marcos Antônio Japiassu Resende; Braz, Rodivan

2016-12-01

Objective: The aim of the present study was to compare the effect of pre-treating dentin with chlorhexidine, at concentrations of 0.2% and 2%, and remineralizing paste containing CPP-ACP (MI Paste - GC) on the bond strength of adhesive systems. Material and methods: In total, 80 slides of dentin were used. These slides were 2 mm thick and were obtained from bovine incisors. Standard cavities were created using diamond bur number 3131. In the control groups, a Scotchbond Universal Adhesive (SUA) self-etching adhesive system of 3M ESPE and a Clearfil SE Bond (CSE) adhesive system of Kuraray were applied, following the manufacturer's instructions. In the other groups, dentin was pretreated with chlorhexidine (0.2% and 2%) for 1 min and with MI Paste for 3 min. The cavities were restored with Z350 XT resin (3M ESPE). After 24 h of storage, the push-out test was applied at a speed of 0.5 mm/min. Results: The different dentin pretreatment techniques did not affect the intra-adhesive bond strength. There was a difference between treatment with MI Paste and chlorhexidine 0.2% in favor of the SUA, with values of 15.22 and 20.25 Mpa, respectively. Conclusions: The different pretreatment methods did not alter the immediate bond strength to dentin. Differences were only recorded when comparing the adhesives.

Catalyst dispersion and activity under conditions of temperature-staged liquefaction

Energy Technology Data Exchange (ETDEWEB)

Davis, A.; Schobert, H.H.; Mitchell, G.D.; Artok, L.

1993-02-01

This research program involves the investigation of the use of highly dispersed catalyst precursors for the pretreatment of coals by mild hydrogenation. During the course of this effort solvent preswelling of the coal was evaluated as a means of deeply impregnating catalysts into coal, active phases of catalysts under reaction conditions were studied and the impact of these techniques were evaluated during pretreatment and temperature-staged liquefaction. Two coals, a Texas subbituminous and a Utah high volatile A bituminous, were used to examine the effects of solvent swelling pretreatment and catalyst impregnation on conversion behavior at 275[degrees]C, representative of the first, low-temperature stage in a temperature-staged liquefaction reaction. Ferrous sulfate, iron pentacarbonyl, ammonium tetrathiomolybdate, and molybdenum hexacarbonyl were used as catalyst precursors. Without swelling pretreatment, impregnation of both coals increased conversion, mainly through increased yields of preasphaltenes.

Effective enzymatic in situ saccharification of bamboo shoot shell pretreated by dilute alkalic salts sodium hypochlorite/sodium sulfide pretreatment under the autoclave system.

Science.gov (United States)

Chong, Gang-Gang; He, Yu-Cai; Liu, Qiu-Xiang; Kou, Xiao-Qin; Huang, Xiao-Jun; Di, Jun-Hua; Ma, Cui-Luan

2017-10-01

In this study, dilute alkali salts (0.6% NaClO, 0.067% Na 2 S) pretreatment at 10% sulfidity under the autoclave system at 120°C for 40min was used for pretreating bamboo shoot shell (BSS). Furthermore, FT-IR, XRD and SEM were employed to characterize the changes in the cellulose structural characteristics (porosity, morphology, and crystallinity) of the pretreated BSS solid residue. After 72h, the reducing sugars and glucose from the enzymatic in situ hydrolysis of 50g/L pretreated BSS in dilute NaClO/Na 2 S media could be obtained at 31.11 and 20.32g/L, respectively. Finally, the obtained BSS-hydrolysates containing alkalic salt NaClO/Na 2 S resulted in slightly negative effects on the ethanol production. Glucose in BSS-hydrolysates was fermented from 20.0 to 0.17g/L within 48h, and an ethanol yield of 0.41g/g glucose, which represents 80.1% of the theoretical yield, was obtained. This study provided an effective strategy for potential utilization of BSS. Copyright © 2017 Elsevier Ltd. All rights reserved.

Testing of Candidate Polymeric Materials for Compatibility with Pure Alternate Pretreat as Part of the Universal Waste Management System (UWMS)

Science.gov (United States)

Wingard, C. D.

2018-01-01

The Universal Waste Management System (UWMS) is an improved Waste Collection System for astronauts living and working in low Earth orbit spacecraft. Polymeric materials used in water recovery on International Space Station are regularly exposed to phosphoric acid-treated 'pretreated' urine. Polymeric materials used in UWMS are not only exposed to pretreated urine, but also to concentrated phosphoric acid with oxidizer before dilution known as 'pure pretreat.' Samples of five different polymeric materials immersed in pure pretreat for 1 year were tested for liquid compatibility by measuring changes in storage modulus with a dynamic mechanical analyzer.

Pretreatment methods to obtain pumpable high solid loading wood–water slurries for continuous hydrothermal liquefaction systems

DEFF Research Database (Denmark)

Dãrãbana, Iulia-Maria; Rosendahl, Lasse Aistrup; Pedersen, Thomas Helmer

2015-01-01

Feedstock pretreatment is a prerequisite step for continuous processing of lignocellulosic biomass through HTL, in order to facilitate the pumpability of biomass aqueous slurries. Until now, HTL feedstock pumpability could only be achieved at solid mass content below 15%. In this work, two...... pretreatment methods to obtain wood-based slurries with more than 20% solid mass content, for continuous processing in HTL systems, are proposed. The effect of biomass particle size and pretreatment method on the feedstock pumpability is analyzed. The experimental results show that pumpable wood-based slurries...

FMECA about pre-treatment system for purge gas of test blanket module in ITER

International Nuclear Information System (INIS)

Fu Wanfa; Luo Deli; Tang Tao

2012-01-01

The pre-treatment system for purge gas of TBM will be installed in Port Cell for installing TBM in ITER, the function of which includes filtering purge gas, removing HTO, cooling, and adjusting flow rate, etc. The purge gas treated will be conveyed into TES (Tritium Extraction System). The technological process and system components in pre-treatment system were introduced. Tritium releasing risk was regarded as failure criterion; failure mode, effects and criticality analysis (FMECA) were carried out and several weaknesses or failure mode in the system were found. Besides, risk priority number (RPN) and failure mode criticality were calculated. Finally, some design improvement measures and usage compensation measures were given. At last, four important potential failure modes were found out. The analysis will provide the design basis for reducing risk of excessive tritium releasing, which is also a useful assist for safety analysis about other tritium system. (authors)

Pretreatment of wheat straw by nonionic surfactant-assisted dilute acid for enhancing enzymatic hydrolysis and ethanol production.

Science.gov (United States)

Qi, Benkun; Chen, Xiangrong; Wan, Yinhua

2010-07-01

Pretreating wheat straw (WS) with combined use of varied sulfuric acid concentration (0-3%, w/v) and Tween 20 concentration (0-1%) was investigated in an attempt to enhance the hydrolysis and fermentability of pretreated WS. Enzymatic hydrolysis yield of glucan and xylan and ethanol production by simultaneous saccharification and fermentation (SSF) of water-insoluble solids (WIS) were significantly affected by the amount of Tween 20 added during acid pretreatment. Any further addition of Tween 20 in either hydrolysis stage or fermentation stage only led to small increase in glucan conversion and ethanol production. Determination of adsorption of cellulases during hydrolysis showed that Tween 20-assisted acid treated straw solution contained more free cellulases than individual acid treated straw solution, indicating that modification of lignin surface by Tween 20 added during pretreatment likely occurred. In addition, the effects of pretreatment conditions on overall recovery of glucose and xylose after pretreatment and enzymatic hydrolysis were also investigated. Copyright 2010 Elsevier Ltd. All rights reserved.

Study of Crystallinity Index (CrI) of Oil Palm Frond Pretreatment using Aqueous [EMIM][OAc] in a Closed System

Science.gov (United States)

Abu Darim, R.; Azizan, A.; Salihon, J.

2018-05-01

The objective of this preliminary study is to identify the Crystalinity Index (CrI) of Oil Palm Frond (OPF) pretreated with 40% concentration of 1-ethyl-3-methylimidazolium acetate ionic liquid ([EMIM][OAc]) in a closed system. The morphology and structural changes of the pretreated OPF were examined by using Fourier Transform Infrared Spectrometer (FTIR) and X-Ray Diffraction (XRD). The pretreatment process was carried out in triplicates by loading 40% of [EMIM][OAc] concentration with 10 wt% of OPF loading in the Bio-ionic liquid-reactor. The pretreatment process was conducted for 3 hours with working volume of 70 mL and temperature of 110°C. A Bio-ionic liquid reactor was purposely designed for the lignocellulosic pretreatment by using aqueous ionic liquid at high temperature (higher than boiling point of water). The CrI of OPF pretreated with 40% concentration of [EMM][OAc] in a closed system observed was 9% lower from the untreated OPF and the result showed significant difference with 95% confidence level. Further examination of the untreated and pretreated OPF by using XRD showed that the diffraction pattern of the pretreated OPF samples was decreasing compared to the untreated OPF. The characteristic of the FTIR spectra of the pretreated OPF showed the presence of the cellulose I and occurrence of amorphous cellulosic in the samples. The findings from this study are expected to improve knowledge on pretreatment of OPF by using aqueous [EMIM][OAc] as a green economically viable process for future renewable energy.

Engineering and two-stage evolution of a lignocellulosic hydrolysate-tolerant Saccharomyces cerevisiae strain for anaerobic fermentation of xylose from AFEX pretreated corn stover.

Directory of Open Access Journals (Sweden)

Lucas S Parreiras

Full Text Available The inability of the yeast Saccharomyces cerevisiae to ferment xylose effectively under anaerobic conditions is a major barrier to economical production of lignocellulosic biofuels. Although genetic approaches have enabled engineering of S. cerevisiae to convert xylose efficiently into ethanol in defined lab medium, few strains are able to ferment xylose from lignocellulosic hydrolysates in the absence of oxygen. This limited xylose conversion is believed to result from small molecules generated during biomass pretreatment and hydrolysis, which induce cellular stress and impair metabolism. Here, we describe the development of a xylose-fermenting S. cerevisiae strain with tolerance to a range of pretreated and hydrolyzed lignocellulose, including Ammonia Fiber Expansion (AFEX-pretreated corn stover hydrolysate (ACSH. We genetically engineered a hydrolysate-resistant yeast strain with bacterial xylose isomerase and then applied two separate stages of aerobic and anaerobic directed evolution. The emergent S. cerevisiae strain rapidly converted xylose from lab medium and ACSH to ethanol under strict anaerobic conditions. Metabolomic, genetic and biochemical analyses suggested that a missense mutation in GRE3, which was acquired during the anaerobic evolution, contributed toward improved xylose conversion by reducing intracellular production of xylitol, an inhibitor of xylose isomerase. These results validate our combinatorial approach, which utilized phenotypic strain selection, rational engineering and directed evolution for the generation of a robust S. cerevisiae strain with the ability to ferment xylose anaerobically from ACSH.

Electrolytic pretreatment of urine

Science.gov (United States)

1977-01-01

Electrolysis has been under evaluation for several years as a process to pretreat urine for ultimate recovery of potable water in manned spacecraft applications. The conclusions that were drawn from this investigation are the following: (1) A platinum alloy containing 10 percent rhodium has been shown to be an effective, corrosion-resistant anode material for the electrolytic pretreatment of urine. Black platinum has been found to be suitable as a cathode material. (2) The mechanism of the reactions occurring during the electrolysis of urine is two-stage: (a) a total Kjeldahl nitrogen and total organic carbon (TOC) removal in the first stage is the result of electrochemical oxidation of urea to CO2, H2O, and ammonia followed by chloride interaction to produce N2 from ammonia, (b) after the urea has been essentially removed and the chloride ions have no more ammonia to interact with, the chloride ions start to oxidize to higher valence states, thus producing perchlorates. (3) Formation of perchlorates can be suppressed by high/low current operation, elevated temperature, and pH adjustment. (4) UV-radiation showed promise in assisting electrolytic TOC removal in beaker tests, but was not substantiated in limited single cell testing. This may have been due to non-optimum configurations of the single cell test rig and the light source.

Description of waste pretreatment and interfacing systems dynamic simulation model

International Nuclear Information System (INIS)

Garbrick, D.J.; Zimmerman, B.D.

1995-05-01

The Waste Pretreatment and Interfacing Systems Dynamic Simulation Model was created to investigate the required pretreatment facility processing rates for both high level and low level waste so that the vitrification of tank waste can be completed according to the milestones defined in the Tri-Party Agreement (TPA). In order to achieve this objective, the processes upstream and downstream of the pretreatment facilities must also be included. The simulation model starts with retrieval of tank waste and ends with vitrification for both low level and high level wastes. This report describes the results of three simulation cases: one based on suggested average facility processing rates, one with facility rates determined so that approximately 6 new DSTs are required, and one with facility rates determined so that approximately no new DSTs are required. It appears, based on the simulation results, that reasonable facility processing rates can be selected so that no new DSTs are required by the TWRS program. However, this conclusion must be viewed with respect to the modeling assumptions, described in detail in the report. Also included in the report, in an appendix, are results of two sensitivity cases: one with glass plant water recycle steams recycled versus not recycled, and one employing the TPA SST retrieval schedule versus a more uniform SST retrieval schedule. Both recycling and retrieval schedule appear to have a significant impact on overall tank usage

The correlation of PSA nadir and biochemical freedom from cancer after external beam treatment: effects of stage, grade and pretreatment PSA groupings

International Nuclear Information System (INIS)

Pinover, W.H.; Hanlon, A.L.; Lee, W.R.; Hanks, G.E.

1996-01-01

Purpose: This study demonstrates the correlation of various post-irradiation PSA nadirs with long term biochemical freedom from disease (bNED) survival in patients treated mainly with conformal external beam radiation therapy. It also shows the effects of various groupings of pretreatment (prerx) PSA level, stage, and Gleason score on the rate of achieving a favorable PSA nadir. Materials and Methods: Three hundred forty patients with known pretreatment PSA, >2 years followup treated with radiation alone (278 conformal, 62 conventional) are reported. The median followup is 41 months (range 24 to 96 mos.). Patient grouping by pretreatment PSA levels are <10 ng/ml (143 patients), 10-19.9 ng/ml (108 patients), ≥20 ng/ml (89 patients); by palpation stage are T1C,2AB (240 patients) and T2C,3,4 (100 patients); and by differentiation are Gleason 2-4 (108 patients), Gleason 5-7 (221 patients), Gleason 8-10 (11 patients). The PSA nadir response is given for all patients, and for each of the above prerx groupings. The 5 year actuarial bNED survival is determined for all patients by PSA nadir. Biochemical failure is a PSA ≥1.5 ng/ml and rising on two consecutive measures. Multivariate analysis (MVA) is performed to determine factors predictive of favorable PSA nadir response and predictive of bNED survival. Results: The PSA nadir responses and 5 year bNED survival rates are shown in the table for all patients according to PSA nadir. 66% of patients achieved a favorable nadir (<1.0 ng/ml) which was associated with a 75%-87% 5 year bNED rate, while 34% achieved an unfavorable nadir associated with an 18-32% bNED survival rate at 5 years. The figure illustrates the dramatic separation in outcome associated with the nadir response. The table also illustrates the fraction of patients that achieve various nadir levels subdivided by prerx PSA level, palpation stage and Gleason score. A favorable PSA nadir is obtained in 90%, 63%, and 31% of patients with a prerx PSA <10, 10

Tank Waste Remediation System tank waste pretreatment and vitrification process development testing requirements assessment

International Nuclear Information System (INIS)

Howden, G.F.

1994-01-01

A multi-faceted study was initiated in November 1993 to provide assurance that needed testing capabilities, facilities, and support infrastructure (sampling systems, casks, transportation systems, permits, etc.) would be available when needed for process and equipment development to support pretreatment and vitrification facility design and construction schedules. This first major report provides a snapshot of the known testing needs for pretreatment, low-level waste (LLW) and high-level waste (HLW) vitrification, and documents the results of a series of preliminary studies and workshops to define the issues needing resolution by cold or hot testing. Identified in this report are more than 140 Hanford Site tank waste pretreatment and LLW/HLW vitrification technology issues that can only be resolved by testing. The report also broadly characterizes the level of testing needed to resolve each issue. A second report will provide a strategy(ies) for ensuring timely test capability. Later reports will assess the capabilities of existing facilities to support needed testing and will recommend siting of the tests together with needed facility and infrastructure upgrades or additions

Tank Waste Remediation System tank waste pretreatment and vitrification process development testing requirements assessment

Energy Technology Data Exchange (ETDEWEB)

Howden, G.F.

1994-10-24

A multi-faceted study was initiated in November 1993 to provide assurance that needed testing capabilities, facilities, and support infrastructure (sampling systems, casks, transportation systems, permits, etc.) would be available when needed for process and equipment development to support pretreatment and vitrification facility design and construction schedules. This first major report provides a snapshot of the known testing needs for pretreatment, low-level waste (LLW) and high-level waste (HLW) vitrification, and documents the results of a series of preliminary studies and workshops to define the issues needing resolution by cold or hot testing. Identified in this report are more than 140 Hanford Site tank waste pretreatment and LLW/HLW vitrification technology issues that can only be resolved by testing. The report also broadly characterizes the level of testing needed to resolve each issue. A second report will provide a strategy(ies) for ensuring timely test capability. Later reports will assess the capabilities of existing facilities to support needed testing and will recommend siting of the tests together with needed facility and infrastructure upgrades or additions.

Pretreatment Red Blood Cell Total Folate Concentration Is Associated With Response to Pemetrexed in Stage IV Nonsquamous Non-Small-cell Lung Cancer.

Science.gov (United States)

Bagley, Stephen J; Vitale, Steven; Zhang, Suhong; Aggarwal, Charu; Evans, Tracey L; Alley, Evan W; Cohen, Roger B; Langer, Corey J; Blair, Ian A; Vachani, Anil; Whitehead, Alexander S

2017-03-01

Pemetrexed inhibits folate-dependent enzymes involved in pyrimidine and purine synthesis. Previous studies of genetic variation in these enzymes as predictors of pemetrexed efficacy have yielded inconsistent results. We investigated whether red blood cell (RBC) total folate, a phenotypic rather than genotypic, marker of cellular folate status was associated with the response to pemetrexed-based chemotherapy in advanced nonsquamous non-small-cell lung cancer (NSCLC). We conducted a prospective cohort study of patients with stage IV nonsquamous NSCLC receiving first-line chemotherapy containing pemetrexed. The pretreatment RBC total folate level was quantified using liquid chromatography mass spectrometry. We then compared the objective response rate (ORR) between patients with RBC total folate concentrations greater than and less than an optimal cutoff value determined from the receiver operating characteristic curve. A logistic regression model was used to adjust for age, sex, and the use of bevacizumab. The ORR was 62% (32 of 52 patients). Receiver operating characteristic analysis was used to establish that a RBC total folate cutoff value of 364.6 nM optimally discriminated between pemetrexed responders and nonresponders. Patients with RBC total folate  364.5 nM (P = .01). This difference persisted after adjusting for age, sex, and the use of bevacizumab (odds ratio, 0.07; 95% confidence interval, 0.01-0.57; P = .01). A low pretreatment RBC total folate was associated with an inferior response to pemetrexed-based chemotherapy in stage IV nonsquamous NSCLC. Larger, multicenter studies are needed to validate RBC total folate as a predictive marker of pemetrexed response. Copyright © 2016 Elsevier Inc. All rights reserved.

Two-stage alkaline hydrothermal liquefaction of wood to biocrude in a continuous bench-scale system

DEFF Research Database (Denmark)

Sintamarean, Iulia-Maria; Grigoras, Ionela; Jensen, Claus Uhrenholt

2017-01-01

unit. In total, 100 kg of wood paste with 25% dry matter is processed at 400 °C and 30 MPa, demonstrating the usefulness of this two-stage liquefaction strategy. An additional advantage liquefaction of such pretreated wood shows increased biocrude yields with approximately 10% compared to the case...

Operation of staged membrane oxidation reactor systems

Science.gov (United States)

Repasky, John Michael

2012-10-16

A method of operating a multi-stage ion transport membrane oxidation system. The method comprises providing a multi-stage ion transport membrane oxidation system with at least a first membrane oxidation stage and a second membrane oxidation stage, operating the ion transport membrane oxidation system at operating conditions including a characteristic temperature of the first membrane oxidation stage and a characteristic temperature of the second membrane oxidation stage; and controlling the production capacity and/or the product quality by changing the characteristic temperature of the first membrane oxidation stage and/or changing the characteristic temperature of the second membrane oxidation stage.

Prostate-specific antigen for pretreatment prediction and posttreatment evaluation of outcome after definitive irradiation for prostate cancer

Energy Technology Data Exchange (ETDEWEB)

Kuban, Deborah A; El-Mahdi, Anas M; Schellhammer, Paul F

1995-05-15

Purpose: This study was undertaken to assess the predictive value of pretreatment prostate-specific antigen (PSA) and the difference between clinical and PSA disease-free status in patients with long-term follow-up after irradiation for prostatic carcinoma. Comparison of the distribution of prognostic factors between surgical and radiation series was also made. Methods and Materials: From 1975-1989, 652 patients with clinical Stage A2-C prostatic adenocarcinoma were definitively irradiated using external beam therapy. One hundred and fifty patients with banked serum and up to 14 years follow-up have pretreatment PSA levels and 355 patients with up to 17 years follow-up have posttreatment values. Treatment failure was analyzed by tumor stage, grade, and four pretreatment PSA categories. Disease-progression was evaluated by clinical and biochemical (PSA) endpoints. Prognostic factors were compared to two surgical series. Results: A significant difference was seen in clinical and PSA disease-free (PSA {<=} 4.0 ng/ml) status based on tumor grade, stage, and pretreatment PSA category. Although the expected clinical outcome has been well-documented previously, results based on posttreatment PSA levels show 5-year disease-free survivals reduced by 10-16% and 10-year survivals lessened by 15-39% depending upon the particular tumor grade and stage. The earlier stage, lower grade tumors showed the largest difference between clinical and biochemical recurrence rates at the longest interval from treatment. Even more notable were the differences in the clinical and PSA disease-free rates based on the pretreatment PSA level. Comparing the irradiated patients to two surgical series showed that the former had a larger percentage of more advanced stage tumors with more unfavorable PSA levels as compared to prostatectomy patients. Conclusion: With long-term follow-up, the pretreatment PSA level continues to be a powerful predictor of clinical and biochemical outcome in patients

Catalyst dispersion and activity under conditions of temperature-staged liquefaction. Final report

Energy Technology Data Exchange (ETDEWEB)

Davis, A.; Schobert, H.H.; Mitchell, G.D.; Artok, L.

1993-02-01

This research program involves the investigation of the use of highly dispersed catalyst precursors for the pretreatment of coals by mild hydrogenation. During the course of this effort solvent preswelling of the coal was evaluated as a means of deeply impregnating catalysts into coal, active phases of catalysts under reaction conditions were studied and the impact of these techniques were evaluated during pretreatment and temperature-staged liquefaction. Two coals, a Texas subbituminous and a Utah high volatile A bituminous, were used to examine the effects of solvent swelling pretreatment and catalyst impregnation on conversion behavior at 275{degrees}C, representative of the first, low-temperature stage in a temperature-staged liquefaction reaction. Ferrous sulfate, iron pentacarbonyl, ammonium tetrathiomolybdate, and molybdenum hexacarbonyl were used as catalyst precursors. Without swelling pretreatment, impregnation of both coals increased conversion, mainly through increased yields of preasphaltenes.

An evaluation of dilute acid and ammonia fiber explosion pretreatment for cellulosic ethanol production.

Science.gov (United States)

Mathew, Anil Kuruvilla; Parameshwaran, Binod; Sukumaran, Rajeev Kumar; Pandey, Ashok

2016-01-01

The challenge associated with cellulosic ethanol production is maximizing sugar yield at low cost. Current research is being focused to develop a pretreatment method to overcome biomass recalcitrance in an efficient way. This review is focused on two major pretreatments: dilute acid (DA) and ammonia fiber explosion (AFEX) pretreatment of corn stover and how these pretreatment cause morphological and chemical changes to corn stover in order to overcome the biomass recalcitrance. This review highlights the key differences of these two pretreatments based on compositional analysis, cellulose and its crystallinity, morphological changes, structural changes to lignin, enzymatic reactivity and enzyme adsorption onto pretreated solids and finally cellulosic ethanol production from the hydrolysate of DA and AFEX treated corn stover. Each stage of the process, AFEX pretreated corn stover was superior to DA treated corn stover. Copyright © 2015 Elsevier Ltd. All rights reserved.

Development of an integrated pretreatment fractionation process for fermentable sugars and lignin: Application to almond (Prunus dulcis) shell

International Nuclear Information System (INIS)

Gong, Dachun; Holtman, Kevin M.; Franqui-Espiet, Diana; Orts, William J.; Zhao, Ruming

2011-01-01

An environmentally friendly pretreatment process was developed to fractionate cellulose, hemicellulose and lignin from almond (Prunus dulcis) shells, consisting of hot water pretreatment (HWP) coupled with organic solvent (organosolv) pretreatment of water/ethanol (OWEP). This integrated pretreatment process proved more effective on the basis of yield of fermentable sugar and lignin separation compared with HWP alone, dilute acid pretreatment (DAP), ammonia pretreatment (AP), lime pretreatment LP, organosolv water/ethanol pretreatment (OWEP), and organosolv water/acetone pretreatment (OWAP). In the coupled hot water-organosolv process, hemicellulose sugars were recovered in the first residual liquid while varying amounts of cellulose was retained in the residual solid. The lignin fraction was obtained by simply adjusting the pH from the second liquid. The optimal two-stage process consisted of first HWP stage at 195 o C for 30 min, resulting in w glucose = 95.4% glucose recovery yield and w xylose = 92.2% xylose removal. The second organosolv OWEP stage was operated at 195 o C for 20 min, in ethanol in water mixtures of ethanol = 50% and resulted in nearly w glucose = 100% glucose recovery yield, w xylose = 90% xylose and w lignin = 61% lignin removal. After enzymatic hydrolysis, glucose yield was up to w glucose = 95%, compared to 61% yield from untreated almond. Images obtained via scanning electron microscopy (SEM) highlighted the differences in almond structure from the varying pretreatment methods during biomass fractionation. -- Highlights: → Almond shells are an under-utilized agriculture byproduct available in the world. → Almond shells are particularly attractive as bioenergy feedstock. → We have developed a new fractionation process for the almond shell. → The new process combined the HWP with OWEP. → The fractionation process has potential in the utilization of almond shell.

CT and MRI appearances and radiologic staging of pediatric renal cell carcinoma

Energy Technology Data Exchange (ETDEWEB)

Downey, Ryan T. [University of Michigan Health System, Department of Radiology, Ann Arbor, MI (United States); Dillman, Jonathan R.; Ladino-Torres, Maria F.; Strouse, Peter J. [University of Michigan Health System, Section of Pediatric Radiology, C.S. Mott Children' s Hospital, Department of Radiology, Ann Arbor, MI (United States); McHugh, Jonathan B. [University of Michigan Health System, Department of Pathology, Ann Arbor, MI (United States); Ehrlich, Peter F. [University of Michigan Health System, Department of Surgery, Section of Pediatric Surgery, Ann Arbor, MI (United States)

2012-04-15

Renal cell carcinoma (RCC) is an uncommon but noteworthy primary pediatric renal malignancy. There is a paucity of published data regarding the CT/MRI appearances and accuracy of pretreatment radiologic staging of this form of cancer in children. To review the various CT/MRI appearances of pediatric RCC and assess the accuracy of pretreatment radiologic staging using these imaging modalities. Institutional Departments of Pathology and Radiology records were searched from 1995 through 2010 for children (younger than 18 years of age) with RCC. Available pretreatment contrast-enhanced abdominopelvic CT and MRI examinations were reviewed by two radiologists. Pertinent imaging findings were documented by consensus, and correlation was made between radiologic and surgicopathological TNM staging. Pretreatment imaging studies from 10 RCCs in nine children (four girls and five boys; mean age 12.9 years) were reviewed. The mean size of the primary tumor was 6.2 cm (range, 1.5-12.6 cm). Ninety percent of RCCs demonstrated heterogeneous postcontrast enhancement. Fifty percent of masses had associated hemorrhage, while 40% contained internal calcification. Regarding TNM staging, N staging was correct for 10 of 10 tumors, while M staging was correct for 10 of 10 tumors. Imaging correctly staged only 4 of 10 tumors with respect to T stage. Radiologic and surgicopathological overall staging were concordant for 8 of 10 tumors. Pediatric RCCs typically present as large, heterogeneous masses, and they commonly hemorrhage and contain internal calcification. Radiologic and surgicopathological overall TNM staging are frequently concordant, although radiologic T staging is often incorrect. (orig.)

Removal performance of toluene, p-xylene and ethylene using a plasma-pretreated biotrickling system

Energy Technology Data Exchange (ETDEWEB)

Kim, H.J.; Han, B.; Kim, S.J.; Kim, Y.J. [Korea Inst. of Machinery and Materials (Korea, Republic of)

2010-07-01

The use of biological systems for removing volatile organic compounds (VOCs) from gaseous emissions was discussed. The systems rely on microorganism activity and do not produce any secondary pollution. Recently, the integration of biofiltration and UV photooxidation has been performed to remove VOCs in air. The systems using both UV photooxidation and biofiltration removed recalcitrant and VOCs more effectively than a stand-alone process using only biofiltration, because the UV pre-treatment not only removes the gases, but also changes them to easily biodegradable and water soluble byproducts such as acids and aldehydes. The biotrickling filter in this study was exposed to toluene gas only for over one month to cultivate specific microorganisms. The non-thermal plasma was a dielectric barrier discharge (DBD) plasma. The performance for removing toluene, p-xylene, and ethylene by the biotrickling filter, the plasma reactor and the plasma-pretreated bio-trickling system was investigated at a variety of flow rates and inlet concentrations of the test gases. The experimental results showed that the removal efficiencies of the integrated system of non-thermal plasma and biotrickling filter for p-xylene and ethylene were enhanced by 28.0 and 29.7 percent respectively, and increased by only 5.3 percent for toluene, as compared to those of the stand-alone biotrickling filtration. It was concluded that the plasma-pretreated biofiltration system could enhance the performance of the biotrickling filter for removing VOC gases, particularly for reducing low biodegradable pollutants with high loading which are chemically different from the cultivated gases. 12 refs., 7 figs.

Enzyme pretreatment of fats, oil and grease from restaurant waste to prolong septic soil treatment system effectiveness.

Science.gov (United States)

Dong, Younsuk; Safferman, Steven I; Ostahowski, Jeff; Herold, Tom; Panter, Ronald

2017-01-02

When a fast-food restaurant's wastewater containing fats, oil and grease (FOG) is discharged into a collection system, it builds up over time and clogs pipes. Similarly, when such wastewater flows into a septic soil treatment system, it adheres to the surface of inlet pipes, gravel/distribution media and soil, restricting the flow and eventually clogging the septic soil treatment system. In this study, an enzymatic pretreatment system was tested on wastewater from a fast-food restaurant to determine its effectiveness in preventing septic soil treatment system clogging. This system used aeration equipment, baffles and a one-time inoculum that excretes enzymes to reduce the molecular weight and number of double bonds associated with FOG. FOG containing triglycerides having lower molecular weights and fewer double bonds are less sticky. The enzymatic pretreatment system was found to cause these changes as verified by measuring the types of triglycerides (compounds in FOG) using liquid chromatography/mass spectrometry. A unique bench-scale septic soil treatment system (soil trench) was also used. Each contained six soil moisture sensors to enable the determination of moisture saturation trends among the five tested conditions: sanitary wastewater only, a combination of sanitary and kitchen wastewater, enzymatically pretreated sanitary and kitchen wastewater, kitchen wastewater, and enzymatically pretreated kitchen wastewater. For all influent types, a significant amount of FOG and other pollutants were removed, regardless of the initial concentrations. Moisture sensor readings showed differences among the tested conditions, indicating that septic soil treatment system clogging was delayed. Inspection of the influent pipe and gravel at the end of testing verified these differences as did the measurements of volatile solids.

COOLING STAGES OF CRYOGENIC SYSTEMS

OpenAIRE

Троценко, А. В.

2011-01-01

The formalized definition for cooling stage of low temperature system is done. Based on existing information about the known cryogenic unit cycles the possible types of cooling stages are single out. From analyses of these stages their classification by various characteristics is suggested. The results of thermodynamic optimization of final throttle stage of cooling, which are used as working fluids helium, hydrogen and nitrogen, are shown.

Pretreatment red blood cell total folate is associated with response to pemetrexed in stage IV non-squamous non-small-cell lung cancer

Science.gov (United States)

Bagley, Stephen J.; Vitale, Steven; Zhang, Suhong; Aggarwal, Charu; Evans, Tracey L.; Alley, Evan W.; Cohen, Roger B.; Langer, Corey J.; Blair, Ian A.; Vachani, Anil; Whitehead, Alexander S.

2016-01-01

Objectives Pemetrexed inhibits folate-dependent enzymes involved in pyrimidine and purine synthesis. Prior studies of genetic variation in these enzymes as predictors of pemetrexed efficacy have yielded inconsistent results. We investigated whether red blood cell (RBC) total folate, a phenotypic rather than genotypic marker of cellular folate status, was associated with response to pemetrexed-based chemotherapy in advanced non-squamous non-small-cell lung cancer (NSCLC). Materials and methods We conducted a prospective cohort study of patients with stage IV non-squamous NSCLC receiving first-line chemotherapy containing pemetrexed. Pretreatment RBC total folate was quantified using liquid chromatography/mass spectrometry. We then compared objective response rate (ORR) between patients with RBC total folate concentrations above and below an optimal cut-off value determined from the receiver operating characteristic (ROC) curve. A logistic regression model was used to adjust for age, sex, and use of bevacizumab. Results The ORR was 62% (32 of 52 patients). ROC analysis was used to establish that a RBC total folate cutoff value of 364.6 nM optimally discriminated between pemetrexed responders and non-responders. Patients with RBC total folate below 364.5 nM had an ORR of 27%, compared to 71% in patients with RBC total folate above this value (p=0.01). This difference persisted after adjusting for age, sex, and use of bevacizumab (OR 0.07, 95% CI 0.01 - 0.57, p=0.01). Conclusions Low pretreatment RBC total folate is associated with inferior response to pemetrexed-based chemotherapy in stage IV non-squamous NSCLC. Larger, multicenter studies are needed to validate RBC total folate as a predictive marker of pemetrexed response. PMID:27863923

Prognostic value of pretreatment serum carcinoembryonic antigen and squamous cell carcinoma antigen levels for patients with stage I-III non-small cell lung cancer treated with radiation therapy alone

International Nuclear Information System (INIS)

Saito, Yoshihiro; Mitsuhashi, Norio; Hayakawa, Kazushige

1998-01-01

Serum carcinoembryonic antigen (CEA) and serum squamous cell carcinoma antigen (SCC Ag) levels have been reported to be useful as prognostic factors, indicators of clinical response, and predictors for recurrence in patients with lung cancer treated by surgery or chemotherapy. We investigated whether pretreatment serum CEA and SCC Ag levels were useful as independent prognostic factors in patients with stage I to III non-small cell lung cancer who were treated with radiation therapy alone. The serum CEA and SCC Ag levels were measured in 158 and 47 patients, respectively, before radiation therapy. Serum CEA and SCC Ag levels were measured by sandwich radioimmunoassay using the CEA-RIA (radioimmunoassay) kit and the SCC-RIA kit. Serum CEA and SCC Ag levels were above reference values in 19% and 30% of the patients, respectively. The 5-year survival rates were significantly better for patients with a negative SCC Ag result than for those with positive SCC Ag levels (p=0.0001), though no significant difference in survival rates was seen by CEA positivity (p=0.25). SCC Ag positivity (p=0.0006) and stage (p=0.04) were the important prognostic factors, as determined by multivariate analyses. Pretreatment serum SCC Ag level may be useful as an independent prognostic factor in patients with stage I to III non-small cell lung cancer who are treated with radiation therapy alone. (author)

Optimization of the enzyme system for hydrolysis of pretreated lignocellulose substrates; Optimering av enzymsystemet foer hydrolys av foerbehandlade lignocellulosa substrat

Energy Technology Data Exchange (ETDEWEB)

Tjerneld, Folke [Lund univ., (Sweden). Dept. of Biochemistry

2000-06-01

This project aims to clarify the reasons for the slow and incomplete enzymatic hydrolysis of certain lignocellulose substrates, particularly softwood e.g. spruce. Based on this knowledge we will optimize the enzyme system so that the yield of fermentable sugars is increased as well as the rate of hydrolysis. We will also study methods for recycling of the enzymes in the process by adsorption on fresh substrate. Progress in these areas will lead to improved process economy in an ethanol process. We collaborate with Chemical Engineering on hydrolysis of pretreated lignocellulose substrates and with Analytical Chemistry and Applied Microbiology on analysis of potential inhibitors. Within this main research direction the work at Biochemistry during this project period (since 970701) has been focused on the following areas: (1) Studies of the role of substrate properties in the enzymatic hydrolysis to clarify the reasons for the decrease in the rate of hydrolysis; (2) enzyme adsorption on lignin; (3) studies of recently identified low molecular weight endo glucanases which may be used for more effective penetration of small pores in pretreated substrates (this part is financed by the Nordic Energy Research Program). Central results during the period: In order to study the role of substrate properties for hydrolysis we have initiated investigations on steam pretreated substrates with several techniques. Measurements of pore sizes have been done with probe molecules of known molecular weights. Results show that probe molecules with diameters larger than 50 Aangstroem can more easily penetrate pretreated willow compared with spruce, which can be a part of the explanation for the better hydrolysability of hardwood substrates compared with softwood. We have started studies with electron microscopy of pretreated substrates at different degrees of enzymatic hydrolysis. With scanning electron microscopy (SEM) we can see significant differences in substrate structure in

Ethanol production from bamboo using mild alkaline pre-extraction followed by alkaline hydrogen peroxide pretreatment.

Science.gov (United States)

Yuan, Zhaoyang; Wen, Yangbing; Kapu, Nuwan Sella

2018-01-01

A sequential two-stage pretreatment process comprising alkaline pre-extraction and alkaline hydrogen peroxide pretreatment (AHP) was investigated to convert bamboo carbohydrates into bioethanol. The results showed that mild alkaline pre-extraction using 8% (w/w) sodium hydroxide (NaOH) at 100°C for 180min followed by AHP pretreatment with 4% (w/w) hydrogen peroxide (H 2 O 2 ) was sufficient to generate a substrate that could be efficiently digested with low enzyme loadings. Moreover, alkali pre-extraction enabled the use of lower H 2 O 2 charges in AHP treatment. Two-stage pretreatment followed by enzymatic hydrolysis with only 9FPU/g cellulose led to the recovery of 87% of the original sugars in the raw feedstock. The use of the pentose-hexose fermenting Saccharomyces cerevisiae SR8u strain enabled the utilization of 95.7% sugars in the hydrolysate to reach 4.6%w/v ethanol titer. The overall process also enabled the recovery of 62.9% lignin and 93.8% silica at high levels of purity. Copyright © 2017 Elsevier Ltd. All rights reserved.

Cell-wall structural changes in wheat straw pretreated for bioethanol production

Science.gov (United States)

Jan B. Kristensen; G. Thygesen Lisbeth; Claus Felby; Henning Jorgensen; Thomas Elder

2008-01-01

Pretreatment is an essential step in the enzymatic hydrolysis of biomass and subsequent production of bioethanol. Recent results indicate that only a mild pretreatment is necessary in an industrial, economically feasible system. The Integrated Biomass Utilisation System hydrothermal pretreatment process has previously been shown to be effective in preparing wheat straw...

Biomass pretreatment

Science.gov (United States)

Hennessey, Susan Marie; Friend, Julie; Elander, Richard T; Tucker, III, Melvin P

2013-05-21

A method is provided for producing an improved pretreated biomass product for use in saccharification followed by fermentation to produce a target chemical that includes removal of saccharification and or fermentation inhibitors from the pretreated biomass product. Specifically, the pretreated biomass product derived from using the present method has fewer inhibitors of saccharification and/or fermentation without a loss in sugar content.

Impact of microwave pre-treatment on the batch anaerobic digestion of two-phase olive mill solid residue: a kinetic approach

International Nuclear Information System (INIS)

Rincon, B.; Gonzalez de Canales, M.; Martin, A.; Borja, R.

2016-01-01

The effect of a microwave (MW) pre-treatment on two-phase olive mill solid residue (OMSR) or alperujo with a view to enhancing its anaerobic digestibility was studied. The MW pre-treatment was carried out at a power of 800 W and at a targeted temperature of 50 °C using different heating rates and holding times. The following specific energies were applied: 4377 kJ·kg TS−1 (MW1), 4830 kJ·kg TS−1 (MW2), 7170 kJ·kg TS−1 (MW3) and 7660 kJ·kg TS−1 (MW4). The maximum methane yield, 395±1 mL CH4·g VSadded−1, was obtained for MW4. The effect of the pre-treatment on the kinetics of the process was also studied. The methane production curves generated during the batch tests showed a first exponential stage and a second sigmoidal stage for all the cases studied. In the first stage, the kinetic constant for the pre-treatment MW1 was 54.8% higher than that obtained for untreated OMSR. [es

Activation of glassy carbon electrodes by photocatalytic pretreatment

Energy Technology Data Exchange (ETDEWEB)

Dumanli, Onur [Department of Chemistry, Faculty of Science and Art, Ondokuz Mayis University, Kurupelit, 55139 Samsun (Turkey); Onar, A. Nur [Department of Chemistry, Faculty of Science and Art, Ondokuz Mayis University, Kurupelit, 55139 Samsun (Turkey)], E-mail: nonar@omu.edu.tr

2009-11-01

This paper describes a simple and rapid photocatalytic pretreatment procedure that removes contaminants from glassy carbon (GC) surfaces. The effectiveness of TiO{sub 2} mediated photocatalytic pretreatment procedure was compared to commonly used alumina polishing procedure. Cyclic voltammetric and chronocoulometric measurements were carried out to assess the changes in electrode reactivity by using four redox systems. Electrochemical measurements obtained on photocatalytically treated GC electrodes showed a more active surface relative to polished GC. In cyclic voltammograms of epinephrine, Fe(CN){sub 6}{sup 3-/4-} and ferrocene redox systems, higher oxidation and reduction currents were observed. The heterogeneous electron transfer rate constants (k{sup o}) were calculated for Fe(CN){sub 6}{sup 3-/4-} and ferrocene which were greater for photocatalytic pretreatment. Chronocoulometry was performed in order to find the amount of adsorbed methylene blue onto the electrode and was calculated as 0.34 pmol cm{sup -2} for photocatalytically pretreated GC. The proposed photocatalytic GC electrode cleansing and activating pretreatment procedure was more effective than classical alumina polishing.

Staged membrane oxidation reactor system

Science.gov (United States)

Repasky, John Michael; Carolan, Michael Francis; Stein, VanEric Edward; Chen, Christopher Ming-Poh

2012-09-11

Ion transport membrane oxidation system comprising (a) two or more membrane oxidation stages, each stage comprising a reactant zone, an oxidant zone, one or more ion transport membranes separating the reactant zone from the oxidant zone, a reactant gas inlet region, a reactant gas outlet region, an oxidant gas inlet region, and an oxidant gas outlet region; (b) an interstage reactant gas flow path disposed between each pair of membrane oxidation stages and adapted to place the reactant gas outlet region of a first stage of the pair in flow communication with the reactant gas inlet region of a second stage of the pair; and (c) one or more reactant interstage feed gas lines, each line being in flow communication with any interstage reactant gas flow path or with the reactant zone of any membrane oxidation stage receiving interstage reactant gas.

Hazard Analysis for the Pretreatment Engineering Platform (PEP)

Energy Technology Data Exchange (ETDEWEB)

Sullivan, Robin S.; Geeting, John GH; Lawrence, Wesley E.; Young, Jonathan

2008-07-10

The Pretreatment Engineering Platform (PEP) is designed to perform a demonstration on an engineering scale to confirm the Hanford Waste Treatment Plant Pretreatment Facility (PTF) leaching and filtration process equipment design and sludge treatment process. The system will use scaled prototypic equipment to demonstrate sludge water wash, caustic leaching, oxidative leaching, and filtration. Unit operations to be tested include pumping, solids washing, chemical reagent addition and blending, heating, cooling, leaching, filtration, and filter cleaning. In addition, the PEP will evaluate potential design changes to the ultrafiltration process system equipment to potentially enhance leaching and filtration performance as well as overall pretreatment throughput. The skid-mounted system will be installed and operated in the Processing Development Laboratory-West at Pacific Northwest National Laboratory (PNNL) in Richland, Washington.

Two-stage implant systems.

Science.gov (United States)

Fritz, M E

1999-06-01

Since the advent of osseointegration approximately 20 years ago, there has been a great deal of scientific data developed on two-stage integrated implant systems. Although these implants were originally designed primarily for fixed prostheses in the mandibular arch, they have been used in partially dentate patients, in patients needing overdentures, and in single-tooth restorations. In addition, this implant system has been placed in extraction sites, in bone-grafted areas, and in maxillary sinus elevations. Often, the documentation of these procedures has lagged. In addition, most of the reports use survival criteria to describe results, often providing overly optimistic data. It can be said that the literature describes a true adhesion of the epithelium to the implant similar to adhesion to teeth, that two-stage implants appear to have direct contact somewhere between 50% and 70% of the implant surface, that the microbial flora of the two-stage implant system closely resembles that of the natural tooth, and that the microbiology of periodontitis appears to be closely related to peri-implantitis. In evaluations of the data from implant placement in all of the above-noted situations by means of meta-analysis, it appears that there is a strong case that two-stage dental implants are successful, usually showing a confidence interval of over 90%. It also appears that the mandibular implants are more successful than maxillary implants. Studies also show that overdenture therapy is valid, and that single-tooth implants and implants placed in partially dentate mouths have a success rate that is quite good, although not quite as high as in the fully edentulous dentition. It would also appear that the potential causes of failure in the two-stage dental implant systems are peri-implantitis, placement of implants in poor-quality bone, and improper loading of implants. There are now data addressing modifications of the implant surface to alter the percentage of

Effect of pretreatment of molasses and recycling of yeast on ethanol fermentation

Energy Technology Data Exchange (ETDEWEB)

Samaniego, R; Srivastas, R L

1971-01-01

The effect of pretreatment of molasses and recycling yeast for the removal of calcium, potassium, coloring matter, and colloidal substances on the production of ethanol from the fermentation of molasses was studied. Highest yield of ethanol (9.1%) was obtained from molasses pretreated with egg albumin followed by the treatment with ethanol(8.5%) and H/sub 2/SO/sub 4/ (8.1%) as compared to control (7.9%). Pretreatment with Al/sub 2/(SO/sub 4/)/sub 3/ and activated C did not improve yield. Lowest yield was recorded with tartaric acid. The washing of yeast with HCl (pH 3.5) resulted in higher yields of ethanol as compared to control in all stages of recyclings. Pretreatment of yeast with 5% NaCl retarded the fermentation rate and caused low yield of ethanol. A combined effect of H/sub 2/SO/sub 4/ and HCl showed no essential difference in yields of ethanol except in the third recycling.

Pre-treatment of substrates for biogas production - A systems analysis; Foerbehandling av biogassubstrat i systemanalys

Energy Technology Data Exchange (ETDEWEB)

Carlsson, My; Holmstroem, David; Lagerkvist, Anders; Bisaillon, Mattias

2013-09-01

The present expansion of biogas capacity responds to a growing demand for renewable vehicle fuels. Biodegradable wastes are attractive substrates and are also prioritized in national policy. The full potential of the substrates can rarely be used however. This is partly due to impurities, or the availability or degradation speed may be limiting the biogas yield. In both cases there is a need of pre-treatments. This work deals with the system impacts of pre-treatment aiming to remove impurities in food waste and pre-treatments aiming to improve the biogas yield of horse manure and ley. In the latter case steam explosion and extrusion were the treatments studied. Gas yields and the plant and system impacts on energy, climate and economic were studied. The system includes the biogas plant as well as the impact in supplementary systems for heat and power production. The three named substrates were identified to be highly prioritised due to their total potential and the improvements possible in its realisation. Existing information from literature and contacts has form the data basis, with the addition of a few supplementary analyses of substrates. The project has been operated by the authors with participation of a group of facility operators and external reviewers. Four plants have been visited during the study. Operators of digestion plants and all interested in developing the efficiency of biogas plants are the main target group for the study. The rate that the potential yield of food waste can be utilised depends largely on how efficiently contaminants can be separated without loss of substrate. In this case the separation degree has the main impact on the economy, but not a pronounced climate effect. For all types of pre-treatments the water content of substrates is important, a higher water content is detrimental to economy, energy demand and climate impact. For both the energy balance and the climate impact the generation of vehicle fuel has a large impact. An

Multi-Stage System for Automatic Target Recognition

Science.gov (United States)

Chao, Tien-Hsin; Lu, Thomas T.; Ye, David; Edens, Weston; Johnson, Oliver

2010-01-01

A multi-stage automated target recognition (ATR) system has been designed to perform computer vision tasks with adequate proficiency in mimicking human vision. The system is able to detect, identify, and track targets of interest. Potential regions of interest (ROIs) are first identified by the detection stage using an Optimum Trade-off Maximum Average Correlation Height (OT-MACH) filter combined with a wavelet transform. False positives are then eliminated by the verification stage using feature extraction methods in conjunction with neural networks. Feature extraction transforms the ROIs using filtering and binning algorithms to create feature vectors. A feedforward back-propagation neural network (NN) is then trained to classify each feature vector and to remove false positives. The system parameter optimizations process has been developed to adapt to various targets and datasets. The objective was to design an efficient computer vision system that can learn to detect multiple targets in large images with unknown backgrounds. Because the target size is small relative to the image size in this problem, there are many regions of the image that could potentially contain the target. A cursory analysis of every region can be computationally efficient, but may yield too many false positives. On the other hand, a detailed analysis of every region can yield better results, but may be computationally inefficient. The multi-stage ATR system was designed to achieve an optimal balance between accuracy and computational efficiency by incorporating both models. The detection stage first identifies potential ROIs where the target may be present by performing a fast Fourier domain OT-MACH filter-based correlation. Because threshold for this stage is chosen with the goal of detecting all true positives, a number of false positives are also detected as ROIs. The verification stage then transforms the regions of interest into feature space, and eliminates false positives using an

Prediction of distant metastasis in head neck cancer patients: implications for induction chemotherapy and pre-treatment staging?

International Nuclear Information System (INIS)

Studer, G.; Glanzmann, C.; Seifert, B.

2008-01-01

Background and purpose: intensity modulated radiation therapy (IMRT) combined treatment approaches, surgical and radiodiagnostic advances, respectively, lead to improved local-regional control in head neck cancer (HNC). With increasing local-regional control, distant metastases (DM) become more meaningful. In some trials without concomitant chemotherapy, induction chemotherapy (IC) resulted in an absolute reduction of DM by ∝10-15%. In order to define a more efficient selection of patients at risk for DM with respect to IC and M-staging, we analysed our patients treated by contemporary standards. Patients and methods: between 1/2002 to 12/2007, 409 HNC patients were treated with IMRT; 303/409 (74%) underwent definitive, 106 (26%) postoperative IMRT. The mean/median follow-up was 23/20 months (3-72). 70% tolerated 4-7, 9% 1-3 cycles of simultaneous cisplatin. Treatment followed a prospectively designed protocol. In a previous study with 172 HNC IMRT patients, gross tumor volume (GTV) was found the strongest predictor for local-regional control. In the current study, this criterion has been prospectively tested for DM. Numbers needed to treat were calculated for IC. Results: DM developed in 28/399 (7%) patients; 10 presented initially with DM (total 38/409). In 13/28 (46%), DM remained the only manifestation of disease. GTV was the strongest predictor for DM (p 70 cc; only 6 of them (6/73, 8%) developed isolated DM. Conclusion: GTV was the most significant predictor for DM, that could guide selective pre-treatment M-staging. The subgroup with isolated DM in the high risk group, that could benefit from IC, is small. (orig.)

Investigation of the impacts of thermal pretreatment on waste activated sludge and development of a pretreatment model.

Science.gov (United States)

Burger, Gillian; Parker, Wayne

2013-09-15

This study investigated the impacts of high pressure thermal hydrolysis (HPTH) pretreatment on the distribution of chemical oxygen demand (COD) species in waste activated sludge (WAS). In the first phase of the project, WAS from a synthetically-fed biological reactor (BR) was fed to an aerobic digester (AD). In the second phase, WAS from the BR was pretreated by HPTH at 150 °C and 3 bars for 30 min prior to being fed to the AD. A range of physical, biochemical and biological properties were regularly measured in each process stream in both phases. The COD of the BR WAS consisted of storage products (XSTO), active heterotrophs (XH) and endogenous decay products (XE). Pretreatment did not increase the extent to which the BR WAS was aerobically digested and hence it was concluded that the unbiodegradable COD fraction, i.e. XE, was unchanged by pretreatment. However, pretreatment did increase the rate of degradation as it converted 36% of XH to readily biodegradable COD (SB) and the remaining XH to slowly biodegradable COD (XB). Furthermore, XSTO was fully converted to SB by pretreatment. Although pretreatment did not change the VSS concentration in the downstream aerobic digester, it did decrease the ISS concentration by 46 ± 11%. This reduced the total mass of solids produced by the digester by 21 ± 8%. A COD-based HPTH pretreatment model was developed and calibrated. When this model was integrated into BioWin 3.1(®), it was able to accurately simulate both the steady state performance of the overall system employed in this study as well as dynamic respirometry results. Copyright © 2013 Elsevier Ltd. All rights reserved.

A Novel Pretreatment-Free Duplex Chamber Digital PCR Detection System for the Absolute Quantitation of GMO Samples.

Science.gov (United States)

Zhu, Pengyu; Wang, Chenguang; Huang, Kunlun; Luo, Yunbo; Xu, Wentao

2016-03-18

Digital polymerase chain reaction (PCR) has developed rapidly since it was first reported in the 1990s. However, pretreatments are often required during preparation for digital PCR, which can increase operation error. The single-plex amplification of both the target and reference genes may cause uncertainties due to the different reaction volumes and the matrix effect. In the current study, a quantitative detection system based on the pretreatment-free duplex chamber digital PCR was developed. The dynamic range, limit of quantitation (LOQ), sensitivity and specificity were evaluated taking the GA21 event as the experimental object. Moreover, to determine the factors that may influence the stability of the duplex system, we evaluated whether the pretreatments, the primary and secondary structures of the probes and the SNP effect influence the detection. The results showed that the LOQ was 0.5% and the sensitivity was 0.1%. We also found that genome digestion and single nucleotide polymorphism (SNP) sites affect the detection results, whereas the unspecific hybridization within different probes had little side effect. This indicated that the detection system was suited for both chamber-based and droplet-based digital PCR. In conclusion, we have provided a simple and flexible way of achieving absolute quantitation for genetically modified organism (GMO) genome samples using commercial digital PCR detection systems.

A Novel Pretreatment-Free Duplex Chamber Digital PCR Detection System for the Absolute Quantitation of GMO Samples

Directory of Open Access Journals (Sweden)

Pengyu Zhu

2016-03-01

Full Text Available Digital polymerase chain reaction (PCR has developed rapidly since it was first reported in the 1990s. However, pretreatments are often required during preparation for digital PCR, which can increase operation error. The single-plex amplification of both the target and reference genes may cause uncertainties due to the different reaction volumes and the matrix effect. In the current study, a quantitative detection system based on the pretreatment-free duplex chamber digital PCR was developed. The dynamic range, limit of quantitation (LOQ, sensitivity and specificity were evaluated taking the GA21 event as the experimental object. Moreover, to determine the factors that may influence the stability of the duplex system, we evaluated whether the pretreatments, the primary and secondary structures of the probes and the SNP effect influence the detection. The results showed that the LOQ was 0.5% and the sensitivity was 0.1%. We also found that genome digestion and single nucleotide polymorphism (SNP sites affect the detection results, whereas the unspecific hybridization within different probes had little side effect. This indicated that the detection system was suited for both chamber-based and droplet-based digital PCR. In conclusion, we have provided a simple and flexible way of achieving absolute quantitation for genetically modified organism (GMO genome samples using commercial digital PCR detection systems.

20 years of long-term water balance measurements of a landfill cover system with components constructed from pre-treated dredged material

NARCIS (Netherlands)

Berger, K.; Groengroeft, A.; Gebert, J.; Harms, C.; Eschenbach, A.

2017-01-01

The cover system of the mono-landfill Hamburg-Francop for disposal of dredged
material comprises a mineral liner of pre-treated fine-grained dredged material (‘METHAmaterial’) and an overlying drainage layer of pre-treated sandy dredged material (‘METHAsand’). Water balance and effectiveness of

The Use of Clay-Polymer Nanocomposites in Wastewater Pretreatment

Science.gov (United States)

Rytwo, Giora

2012-01-01

Some agricultural effluents are unsuitable for discharge into standard sewage-treatment plants: their pretreatment is necessary to avoid clogging of the filtering devices by colloidal matter. The colloidal stability of the effluents is mainly due to mutual repulsive forces that keep charged particles in suspension. Pretreatment processes are based on two separate stages: (a) neutralization of the charges (“coagulation”) and (b) bridging between several small particles to form larger aggregates that sink, leaving clarified effluent (“flocculation”). The consequent destabilization of the colloidal suspension lowers total suspended solids (TSSs), turbidity, and other environmental quality parameters, making the treatments that follow more efficient. Clay-based materials have been widely used for effluent pretreatment and pollutant removal. This study presents the use of nanocomposites, comprised of an anchoring particle and a polymer, as “coagoflocculants” for the efficient and rapid reduction of TSS and turbidity in wastewater with a high organic load. The use of such particles combines the advantages of coagulant and flocculant by neutralizing the charge of the suspended particles while bridging between them and anchoring them to a denser particle (the clay mineral), enhancing their precipitation. Very rapid and efficient pretreatment is achieved in one single treatment step. PMID:22454607

Environmentally Friendly Pretreatment for Department of Defense Applications

Science.gov (United States)

2012-08-29

Develop an environmentally friendly pretreatment system for multi-material Department of Defense applications ― Free of hexavalent chromium (Cr6...Zn phosphate and chrome wash primer •Two Zirconium pretreatment variations passed the 336 hr and 1000 hr B-117 outlined per MIL-DTL-53022 or MIL

Comparison of two-stage thermophilic (68 degrees C/55 degrees C) anaerobic digestion with one-stage thermophilic (55 degrees C) digestion of cattle manure

DEFF Research Database (Denmark)

Nielsen, H.B.; Mladenovska, Zuzana; Westermann, Peter

2004-01-01

A two-stage 68degreesC/55degreesC anaerobic degradation process for treatment of cattle manure was studied. In batch experiments, an increase of the specific methane yield, ranging from 24% to 56%, was obtained when cattle manure and its fractions (fibers and liquid) were pretreated at 68degrees......, was compared with a conventional single-stage reactor running at 55degreesC with 15-days HRT. When an organic loading of 3 g volatile solids (VS) per liter per day was applied, the two-stage setup had a 6% to 8% higher specific methane yield and a 9% more effective VS-removal than the conventional single......-stage reactor. The 68degreesC reactor generated 7% to 9% of the total amount of methane of the two-stage system and maintained a volatile fatty acids (VFA) concentration of 4.0 to 4.4 g acetate per liter. Population size and activity of aceticlastic methanogens, syntrophic bacteria, and hydrolytic...

Leachate pretreatment for enhancing organic matter conversion in landfill bioreactor

International Nuclear Information System (INIS)

He Pinjing; Qu Xian; Shao Liming; Li Guojian; Lee Duujong

2007-01-01

Direct recycling of leachate from refuse of high food waste content was shown to ineffectively stabilize the refuse. This work aims at evaluating the effects of three pretreatments of leachate on the refuse stabilization efficiency were investigated. Pretreatment of leachate using an anaerobic upflow filtration bioreactor (UFB) or a well-decomposed waste layer could reduce the COD and provide methanogens, both were beneficial to establish early methanogenesis status. Using an aerobic sequential batch reactor (SBR) to pretreat the leachate could reduce its COD to 1000 mg l -1 , but the fully developed methanogenesis phase would be built up in a later stage. The organic matters in the effluent leachate inhibited both the hydrolysis/acidogenesis and the methanogenesis steps in the refuse. With the dilution and acid neutralization effects by the recycled leachate, a favorable methanogenetic environment could be produced from the column's top, which moved downward along, and finally made the breakthrough of the column

The impacts of pretreatment on the fermentability of pretreated lignocellulosic biomass: a comparative evaluation between ammonia fiber expansion and dilute acid pretreatment

Directory of Open Access Journals (Sweden)

Dale Bruce E

2009-12-01

Full Text Available Abstract Background Pretreatment chemistry is of central importance due to its impacts on cellulosic biomass processing and biofuels conversion. Ammonia fiber expansion (AFEX and dilute acid are two promising pretreatments using alkaline and acidic pH that have distinctive differences in pretreatment chemistries. Results Comparative evaluation on these two pretreatments reveal that (i AFEX-pretreated corn stover is significantly more fermentable with respect to cell growth and sugar consumption, (ii both pretreatments can achieve more than 80% of total sugar yield in the enzymatic hydrolysis of washed pretreated solids, and (iii while AFEX completely preserves plant carbohydrates, dilute acid pretreatment at 5% solids loading degrades 13% of xylose to byproducts. Conclusion The selection of pretreatment will determine the biomass-processing configuration, requirements for hydrolysate conditioning (if any and fermentation strategy. Through dilute acid pretreatment, the need for hemicellulase in biomass processing is negligible. AFEX-centered cellulosic technology can alleviate fermentation costs through reducing inoculum size and practically eliminating nutrient costs during bioconversion. However, AFEX requires supplemental xylanases as well as cellulase activity. As for long-term sustainability, AFEX has greater potential to diversify products from a cellulosic biorefinery due to lower levels of inhibitor generation and lignin loss.

Microstructural study of pre-treated and enzymatic hydrolyzed bamboo

Directory of Open Access Journals (Sweden)

Funsho O. KOLAWOLE

2016-07-01

Full Text Available Bamboo was used as biomass feedstock which was pre-treated using dilute acid hydrolysis followed by enzymatic hydrolysis. The bamboo was mechanical ground to particle sizes 212–500µm, followed by pre-treatment with dilute sulfuric acid at a concentration of 0.5 and 1.0 (%v/v at temperatures of 25, 110, 120, 150 and 200°C with time intervals of 2 and 4 hours. Pre-hydrolyzate was later analyzed for reducing sugar using UV-Vis spectrophotometry. Under the above conditions, a maximum glucose yield of 153.1 mg/g was obtained at 200°C and acid concentrations of 1% for 4 hours. Water insoluble solids obtained were subsequently hydrolyzed with Celluclast (Trichoderma reesi and β-glucosidase (Novozyme 188 for 72 hours. Optical Microscope and ESEM images of bamboo samples were obtained at various stages of pre-treatment and enzymatic hydrolysis. Result reveals a breakdown in the ligno-cellulosic structure of the bamboo during exposure to dilute acid and enzymatic hydrolysis.

Prognostic significance of pretreatment plasma fibrinogen level in patients with digestive system tumors: a meta-analysis.

Science.gov (United States)

Ji, Rui; Ren, Qian; Bai, Suyang; Wang, Yuping; Zhou, Yongning

2018-06-01

High pretreatment levels of plasma fibrinogen have been widely reported to be a potential predictor of prognosis in digestive system tumors; however, the conclusions are not consistent. Therefore, we performed a meta-analysis to comprehensively assess the prognostic roles of high pretreatment plasma fibrinogen levels in digestive system tumors. We searched for eligible studies in the PubMed, Embase, and Web of Science electronic databases for publications from the database inception to 1 September 2017. The endpoints of interest included overall survival, disease-free survival, and recurrence-free survival. We investigated the relationship between fibrinogenemia and overall survival in colorectal cancer (10 studies), gastric cancer (6), pancreatic cancer (6), hepatocellular carcinoma (7), and esophageal squamous cell carcinoma (10); the pooled results indicated that fibrinogenemia was significantly related to a worse overall survival (hazard ratio (HR) 1.73; 95% confidence interval (CI) 1.52, 1.97; P digestive system tumors, indicating that it could be a useful prognostic marker in these types of tumors.

Wash water waste pretreatment system

Science.gov (United States)

1977-01-01

Investigations were completed on wash waters based on each candidate personal cleansing agent. Evaluations of coagulants, antifoam agents, and the effect of promising antifoams on the chemical precipitation were included. Based on these evaluations two candidate soaps as well as their companion antifoam agents were selected for further work. Operating parameters included the effect of soap concentration, ferric chloride concentration, duration of mixing, and pore size of depth filters on the degree of soap removal. The effect of pressure on water flow through filter cartridges and on the rate of decline of water flow was also investigated. The culmination of the program was the recommendation of a pretreatment concept based on chemical precipitation followed by pressure filtration.

Wide-bandwidth bilateral control using two-stage actuator system

International Nuclear Information System (INIS)

Kokuryu, Saori; Izutsu, Masaki; Kamamichi, Norihiro; Ishikawa, Jun

2015-01-01

This paper proposes a two-stage actuator system that consists of a coarse actuator driven by a ball screw with an AC motor (the first stage) and a fine actuator driven by a voice coil motor (the second stage). The proposed two-stage actuator system is applied to make a wide-bandwidth bilateral control system without needing expensive high-performance actuators. In the proposed system, the first stage has a wide moving range with a narrow control bandwidth, and the second stage has a narrow moving range with a wide control bandwidth. By consolidating these two inexpensive actuators with different control bandwidths in a complementary manner, a wide bandwidth bilateral control system can be constructed based on a mechanical impedance control. To show the validity of the proposed method, a prototype of the two-stage actuator system has been developed and basic performance was evaluated by experiment. The experimental results showed that a light mechanical impedance with a mass of 10 g and a damping coefficient of 2.5 N/(m/s) that is an important factor to establish good transparency in bilateral control has been successfully achieved and also showed that a better force and position responses between a master and slave is achieved by using the proposed two-stage actuator system compared with a narrow bandwidth case using a single ball screw system. (author)

Ultrasonic pretreatment of woodchips for the conversion of cellulose to glucose for bioethanol production

International Nuclear Information System (INIS)

Tutun Nugraha; Rettyana Ayuputri; Mohammad Ihsan

2010-01-01

In this study, lignocellulosic biomass i.e. the woodchips of Albacia tree (Paraserianthes falcataria) were given different pretreatment methods, i.e. chemical (acid) and physical (ultrasonic). The pretreatment was given in order to convert the cellulose to glucose for the production of bioethanol. 1 % H_2SO_4 was applied for the acid pretreatment. Ultrasound pretreatment was carried out at varied time (10, 20 and 30 minutes) at 600 W, 20 khz before or after the acid pretreatment. Enzymatic attack of the pretreated sample was also applied to enhance the saccharification process of cellulose. The objective of the research was to determine the most effective ultrasonic duration and the best combination of method for enzymatic hydrolysis of the woodchips. The data showed that the highest yield of glucose was achieved at 20 minutes ultrasonic time. It was also found that substantial amount of hydrolysis of cellulose to glucose occur during the ultrasonic stage even without the presence of acid or cellulose enzyme. It is likely that the highly energetic ultrasonic process alone could assist in enhancing rate of hydrolysis of lignocellulosic cellulose into glucose. (author)

Structural changes in lignin during organosolv pretreatment of Liriodendron tulipifera and the effect on enzymatic hydrolysis

International Nuclear Information System (INIS)

Koo, Bon-Wook; Min, Byeong-Cheol; Gwak, Ki-Seob; Lee, Soo-Min; Choi, Joon-Weon; Yeo, Hwanmyeong; Choi, In-Gyu

2012-01-01

Although organosolv pretreatment removed substantial amounts of lignin and xylan, the yield of glucan which is a major sugar source for fermentation to ethanol is more than 90% in most conditions of the organosolv pretreatment. Relative lignin contents of all pretreated biomass were more than 200 g kg −1 , however enzymatic conversions were increased dramatically comparing to untreated biomass. Therefore the correlation between lignin and enzymatic hydrolysis could not be explained just by lignin content, and other changes resulting from lignin removal affected enzymatic hydrolysis. Results on enzymatic conversion and sugar recovery suggested that the critical temperature improving enzymatic hydrolysis significantly was between 120 °C and 130 °C. Microscopic analysis using Field emission scanning electron microscopy (FE-SEM) showed that structural lignin changes happened through organosolv pretreatment. Lignins were isolated from lignin carbohydrate complex (LCC) at the initial stage and then migrated to the surface of biomass. The isolated and migrated lignins were finally redistributed onto surface. These structural changes formed droplets on surface and increased pore volume in pretreated biomass. The increase in pore volume also increased available surface area and enzyme adsorption at initial stage, and thus enzymatic conversion increased significantly through organosolv pretreatment. It was verified that the droplets were mainly composed of lignin and the lignin droplets inhibited enzymatic hydrolysis through adsorption with cellulase. -- Highlights: ► Just lignin contents cannot explain a correlation with enzymatic hydrolysis. ► Several changes resulted from lignin removal must affect enzymatic hydrolysis. ► Droplets are formed by structural changes in lignin during organosolv pretreatment. ► Formation of the lignin droplet increases the pore volume in biomass. ► The increase in pore volume enhances the enzymatic hydrolysis.

Cell-wall structural changes in wheat straw pretreated for bioethanol production

Directory of Open Access Journals (Sweden)

Jørgensen Henning

2008-04-01

Full Text Available Abstract Background Pretreatment is an essential step in the enzymatic hydrolysis of biomass and subsequent production of bioethanol. Recent results indicate that only a mild pretreatment is necessary in an industrial, economically feasible system. The Integrated Biomass Utilisation System hydrothermal pretreatment process has previously been shown to be effective in preparing wheat straw for these processes without the application of additional chemicals. In the current work, the effect of the pretreatment on the straw cell-wall matrix and its components are characterised microscopically (atomic force microscopy and scanning electron microscopy and spectroscopically (attenuated total reflectance Fourier transform infrared spectroscopy in order to understand this increase in digestibility. Results The hydrothermal pretreatment does not degrade the fibrillar structure of cellulose but causes profound lignin re-localisation. Results from the current work indicate that wax has been removed and hemicellulose has been partially removed. Similar changes were found in wheat straw pretreated by steam explosion. Conclusion Results indicate that hydrothermal pretreatment increases the digestibility by increasing the accessibility of the cellulose through a re-localisation of lignin and a partial removal of hemicellulose, rather than by disruption of the cell wall.

Two-Stage Variable Sample-Rate Conversion System

Science.gov (United States)

Tkacenko, Andre

2009-01-01

A two-stage variable sample-rate conversion (SRC) system has been pro posed as part of a digital signal-processing system in a digital com munication radio receiver that utilizes a variety of data rates. The proposed system would be used as an interface between (1) an analog- todigital converter used in the front end of the receiver to sample an intermediatefrequency signal at a fixed input rate and (2) digita lly implemented tracking loops in subsequent stages that operate at v arious sample rates that are generally lower than the input sample r ate. This Two-Stage System would be capable of converting from an input sample rate to a desired lower output sample rate that could be var iable and not necessarily a rational fraction of the input rate.

Effectiveness of seawater reverse osmosis (SWRO) pretreatment systems in removing transparent exopolymer particles (TEP) substances

KAUST Repository

Lee, Shang-Tse

2015-05-01

Transparent exopolymer particles (TEP) have been reported as one of the main factors of membrane fouling in seawater reverse osmosis (SWRO) process. Research has been focused on algal TEP so far, overlooking bacterial TEP. This thesis investigated the effects of coagulation on removal of bacterial TEP/TEP precursors in seawater and subsequent reduction on TEP fouling in ultrafiltration (UF), as a pretreatment of SWRO. Furthermore, the performance of pretreatment (coagulation + UF) has been investigated on a bench-scale SWRO system. TEP/TEP precursors were harvested from a strain of marine bacteria, Pseudoalteromonas atlantica, isolated from the Red Sea. Isolated bacterial organic matter (BOM), containing 1.5 mg xanthan gum eq./L TEP/TEP precursors, were dosed in Red Sea water to mimic a high TEP concentration event. Bacterial TEP/TEP precursors added to seawater were coagulated with ferric chloride and aluminum sulfate at different dosages and pH. Results showed that ferric chloride had a better removal efficiency on TEP/TEP precursors. Afterwards, the non-coagulated/coagulated seawater were tested on a UF system at a constant flux of 130 L/m2h, using two types of commercially available membranes, with pore sizes of 50 kDa and 100 kDa, respectively. The fouling potential of coagulated water was determined by the Modified Fouling Index (MFI-UF). Transmembrane pressure (TMP) was also continuously monitored to investigate the fouling development on UF membranes. TEP concentrations in samples were determined by the alcian blue staining assay. Liquid chromatography-organic carbon detection (LC-OCD) was used to determine the removal of TEP precursors with particular emphasis on biopolymers. Finally, SWRO tests showed that TEP/TEP precursors had a high fouling potential as indicated by MFI-UF, corresponding to the TMP measurements. Coagulation could substantially reduce TEP/TEP precursors fouling in UF when its dosage was equal or higher than 0.2 mg Fe/L. The flux decline

Thymidine phosphorylase and hypoxia-inducible factor 1-α expression in clinical stage II/III rectal cancer: association with response to neoadjuvant chemoradiation therapy and prognosis.

Science.gov (United States)

Lin, Shuhan; Lai, Hao; Qin, Yuzhou; Chen, Jiansi; Lin, Yuan

2015-01-01

The aim of this study was to determine whether pretreatment status of thymidine phosphorylase (TP), and hypoxia-inducible factor alpha (HIF-1α) could predict pathologic response to neoadjuvant chemoradiation therapy with oxaliplatin and capecitabine (XELOXART) and outcomes for clinical stage II/III rectal cancer patients. A total of 180 patients diagnosed with clinical stage II/III rectal cancer received XELOXART. The status of TP, and HIF-1α were determined in pretreatment biopsies by immunohistochemistry (IHC). Tumor response was assessed in resected regimens using the tumor regression grade system and TNM staging system. 5-year disease free survival (DFS) and 5-year overall survival (OS) were evaluated with the Kaplan-Meier method and were compared by the log-rank test. Over expression of TP and low expression of HIF-1α were associated with pathologic response to XELOXART and better outcomes (DFS and OS) in clinical stage II/III rectal cancer patients (P rectal cancer received XELOXART. Additional well-designed, large sample, multicenter, prospective studies are needed to confirm the result of this study.

Prognostic impact of the pretreatment aspartate transaminase/alanine transaminase ratio in patients treated with first-line systemic tyrosine kinase inhibitor therapy for metastatic renal cell carcinoma.

Science.gov (United States)

Kang, Minyong; Yu, Jiwoong; Sung, Hyun Hwan; Jeon, Hwang Gyun; Jeong, Byong Chang; Park, Se Hoon; Jeon, Seong Soo; Lee, Hyun Moo; Choi, Han Yong; Seo, Seong Il

2018-05-13

To examine the prognostic role of the pretreatment aspartate transaminase/alanine transaminase or De Ritis ratio in patients with metastatic renal cell carcinoma receiving first-line systemic tyrosine kinase inhibitor therapy. We retrospectively searched the medical records of 579 patients with metastatic renal cell carcinoma who visited Samsung Medical Center, Seoul, Korea, from January 2001 through August 2016. After excluding 210 patients, we analyzed 360 patients who received first-line tyrosine kinase inhibitor therapy. Cancer-specific survival and overall survival were defined as the primary and secondary end-points, respectively. A multivariate Cox proportional hazards regression model was used to identify independent prognosticators of survival outcomes. The overall population was divided into two groups according to the pretreatment De Ritis ratio as an optimal cut-off value of 1.2, which was determined by a time-dependent receiver operating characteristic curve analysis. Patients with a higher pretreatment De Ritis ratio (≥1.2) had worse cancer-specific survival and overall survival outcomes, compared with those with a lower De Ritis ratio (<1.2). Notably, a higher De Ritis ratio (≥1.2) was found to be an independent predictor of both cancer-specific survival (hazard ratio 1.61, 95% confidence interval 1.13-2.30) and overall survival outcomes (hazard ratio 1.69, 95% confidence interval 1.19-2.39), along with male sex, multiple metastasis (≥2), non-clear cell histology, advanced pT stage (≥3), previous metastasectomy and the Memorial Sloan Kettering Cancer Center risk classification. Our findings show that the pretreatment De Ritis ratio can provide valuable information about the survival outcomes of metastatic renal cell carcinoma patients receiving first-line tyrosine kinase inhibitor therapy. © 2018 The Japanese Urological Association.

Prognostic Significance of Pre-treatment Serum C-Reactive Protein Level in Patients with Adenocarcinoma of the Uterine Cervix.

Science.gov (United States)

Bodner-Adler, Barbara; Kimberger, Oliver; Schneidinger, Cora; Kölbl, Heinz; Bodner, Klaus

2016-09-01

To evaluate pre-treatment serum C-reactive protein (CRP) level as a prognostic parameter in patients with adenocarcinoma of the uterine cervix. Pre-treatment CRP levels were analyzed to determine potential associations with clinicopathological parameters and to assess prognostic value in 46 patients with sole adenocarcinoma of the uterine cervix. The mean (±SD) pre-treatment serum CRP level was 5.82 (7.21) mg/l. Serum CRP concentration significantly correlated positively with age at diagnosis (p=0.001), lymphovascular space invasion (p=0.0026), recurrent disease (p=0.0001) and International Federation of Gynecology and Obstetrics (FIGO) stage (p=0.0002). In multivariate Cox regression models with age, FIGO stage, histological grade and lymph node status, elevated CRP and cancer antigen 125 levels were associated with shortened survival (pcervix. Copyright© 2016 International Institute of Anticancer Research (Dr. John G. Delinassios), All rights reserved.

Staged fluidized-bed combustion and filter system

International Nuclear Information System (INIS)

Mei, J.S.; Halow, J.S.

1994-01-01

A staged fluidized-bed combustion and filter system are described for substantially reducing the quantity of waste through the complete combustion into ash-type solids and gaseous products. The device has two fluidized-bed portions, the first primarily as a combustor/pyrolyzer bed, and the second as a combustor/filter bed. The two portions each have internal baffles to define stages so that material moving therein as fluidized beds travel in an extended route through those stages. Fluidization and movement is achieved by the introduction of gases into each stage through a directional nozzle. Gases produced in the combustor/pyrolyzer bed are permitted to travel into corresponding stages of the combustor/filter bed through screen filters that permit gas flow but inhibit solids flow. Any catalyst used in the combustor/filter bed is recycled. The two beds share a common wall to minimize total volume of the system. A slightly modified embodiment can be used for hot gas desulfurization and sorbent regeneration. Either side-by-side rectangular beds or concentric beds can be used. The system is particularly suited to the processing of radioactive and chemically hazardous waste. 10 figures

An improved technology for decontaminating ruthenium in uranium purification cycle by hydroxylamine pretreatment

International Nuclear Information System (INIS)

Qi Zhanshun; Zhu Zhixuan; Zhang Pilu

1996-01-01

The Influences of hydroxylamine concentration, pretreatment time, acidity and the concentration of stabilizer have been studied, and the best pretreatment condition for the improvement of Ru decontamination in uranium purification cycle by hydroxylamine pretreatment has been obtained. The results show that no satisfactory result can be obtained by solely using hydroxylamine as pretreatment agent unless a small amount of hydrazine is added into the pretreatment system as stabilizer

Staging of intestinal- and diffuse-type gastric cancers with the OLGA and OLGIM staging systems.

Science.gov (United States)

Cho, S-J; Choi, I J; Kook, M-C; Nam, B-H; Kim, C G; Lee, J Y; Ryu, K W; Kim, Y-W

2013-11-01

Operative link on gastritis assessment (OLGA) and Operative link on gastric intestinal metaplasia assessment (OLGIM) staging systems have been proposed for gastric cancer (GC) risk estimation. To validate the OLGA and OLGIM staging systems in a region with high risk of GC. This retrospective study included 474 GC patients and age- and sex-matched health screening control persons in a cancer centre hospital. We classified gastritis patterns according to the OLGA and OLGIM systems using the histological database that a pathologist prospectively evaluated using the updated Sydney system. GC risk according to the OLGA and OLGIM stages was evaluated using logistic regression analysis. More GC patients had OLGA stages III-IV (46.2%) than controls (26.6%, P diffuse-type GCs (30.9%). OLGA stages III and IV were significantly associated with increased risk of GC [odds ratios (ORs), 2.09; P = 0.008 and 2.04; P = 0.014 respectively] in multivariate analysis. The association was more significant for intestinal-type (ORs, 4.76; P = 0.001 and 4.19; P = 0.002 respectively), but not diffuse-type GC. OLGIM stages from I to IV were significantly associated with increased risk of both intestinal-type (ORs, 3.64, 5.15, 7.89 and 13.20 respectively) and diffuse-type GC (ORs, 1.84, 2.59, 5.08 and 6.32 respectively) with a significantly increasing trend. As high OLGA and OLGIM stages are independent risk factors for gastric cancer, the staging systems may be useful for risk assessment in high-risk regions, especially for intestinal-type gastric cancer. © 2013 John Wiley & Sons Ltd.

Microbial Insight into a Pilot-Scale Enhanced Two-Stage High-Solid Anaerobic Digestion System Treating Waste Activated Sludge.

Science.gov (United States)

Wu, Jing; Cao, Zhiping; Hu, Yuying; Wang, Xiaolu; Wang, Guangqi; Zuo, Jiane; Wang, Kaijun; Qian, Yi

2017-11-30

High solid anaerobic digestion (HSAD) is a rapidly developed anaerobic digestion technique for treating municipal sludge, and has been widely used in Europe and Asia. Recently, the enhanced HSAD process with thermal treatment showed its advantages in both methane production and VS reduction. However, the understanding of the microbial community is still poor. This study investigated microbial communities in a pilot enhanced two-stage HSAD system that degraded waste activated sludge at 9% solid content. The system employed process "thermal pre-treatment (TPT) at 70 °C, thermophilic anaerobic digestion (TAD), and mesophilic anaerobic digestion (MAD)". Hydrogenotrophic methanogens Methanothermobacter spp. dominated the system with relative abundance up to about 100% in both TAD and MAD. Syntrophic acetate oxidation (SAO) bacteria were discovered in TAD, and they converted acetate into H₂ and CO₂ to support hydrogenotrophic methanogenesis. The microbial composition and conversion route of this system are derived from the high solid content and protein content in raw sludge, as well as the operational conditions. This study could facilitate the understanding of the enhanced HSAD process, and is of academic and industrial importance.

Optimization of alkaline and dilute acid pretreatment of agave bagasse by response surface methodology

Directory of Open Access Journals (Sweden)

Abimael I. Ávila-Lara

2015-09-01

Full Text Available Utilization of lignocellulosic materials for the production of value-added chemicals or biofuels generally requires a pretreatment process to overcome the recalcitrance of the plant biomass for further enzymatic hydrolysis and fermentation stages. Two of the most employed pretreatment processes are the ones that used dilute acid (DA and alkaline (AL catalyst providing specific effects on the physicochemical structure of the biomass such as high xylan and lignin removal for DA and AL, respectively. Another important effect that need to be studied is the use of a high solids pretreatment (≥15% since offers many advantaged over lower solids loadings, including increased sugar and ethanol concentrations (in combination with a high solids saccharification which will be reflected in lower capital costs, however this data is currently limited. In this study, several variables such as catalyst loading, retention time and solids loading, were studied using Response Surface Methodology (RSM based on a factorial Central Composite Design (CCD of DA and AL pretreatment on agave bagasse using a range of solids from 3 to 30% (w/w to obtain optimal process conditions for each pretreatment. Subsequently enzymatic hydrolysis was performed using Novozymes Cellic CTec2 and HTec2 presented as total reducing sugar (TRS yield. Pretreated biomass

Microwave pretreatment of switchgrass for bioethanol production

Science.gov (United States)

Keshwani, Deepak Radhakrishin

conditions, 82% glucose and 63% xylose yields were achieved for switchgrass, and 87% glucose and 59% xylose yields were achieved for coastal bermudagrass following enzymatic hydrolysis of the pretreated biomass. The optimum enzyme loadings were 15 FPU/g and 20 CBU/g for switchgrass and 10 FPU/g and 20 CBU/g for coastal bermudagrass. Dielectric properties for dilute sodium hydroxide solutions were measured and compared to solid loss, lignin reduction and reducing sugar levels in hydrolyzates. Results indicate that the dielectric loss tangent of alkali solutions is a potential indicator of the severity of microwave-based pretreatments. Modeling of pretreatment processes can be a valuable tool in process simulations of bioethanol production from lignocellulosic biomass. Chapter 4 discusses three different approaches that were used to model delignification and carbohydrate loss during microwave-based pretreatment of switchgrass: statistical linear regression modeling, kinetic modeling using a time-dependent rate coefficient, and a Mamdani-type fuzzy inference system. The dielectric loss tangent of the alkali reagent and pretreatment time were used as predictors in all models. The statistical linear regression model for delignification gave comparable root mean square error (RMSE) values for training and testing data and predictions were approximately within 1% of experimental values. The kinetic model for delignification and xylan loss gave comparable RMSE values for training and testing data sets and predictions were approximately within 2% of experimental values. The kinetic model for cellulose loss was not as effective and predictions were only within 5-7% of experimental values. The time-dependent rate coefficients of the kinetic models calculated from experimental data were consistent with the heterogeneity (or lack thereof) of individual biomass components. The Mamdani-type fuzzy inference system was shown to be an effective means to model pretreatment processes and gave

[Helicobacter pylori gastritis: assessment of OLGA and OLGIM staging systems].

Science.gov (United States)

Ben Slama, Sana; Ben Ghachem, Dorra; Dhaoui, Amen; Jomni, Mohamed Taieb; Dougui, Mohamed Hédi; Bellil, Khadija

2016-01-01

Helicobacter pylori (H pylori) gastritis presents a risk of cancer related to atrophy and intestinal metaplasia. Two recent classifications OLGA (Operative Link on Gastritis Assessment) and OLGIM (Operative Link on Gastritic Intestinal Metaplasia assessment) have been proposed to identify high-risk forms (stages III and IV). The aim of this study is to evaluate the OLGA and OLGIM staging systems in H pylori gastritis. A descriptive study of 100 cases of chronic H pylori gastritis was performed. The revaluation of Sydney System parameters of atrophy and intestinal metaplasia, of gastric antrum and corpus, allowed identifying respectively the stages of OLGA and OLGIM systems. The progressive risk of our H pylori gastritis was 6% according to OLGA staging and 7% according to OLGIM staging. Significant correlation was revealed between age and OLGA staging. High-risk gastritis according to OLGIM staging was significantly associated with moderate to severe atrophy. High-risk forms according to OLGA staging were associated in 80% of the cases to intestinal metaplasia. OLGA and OLGIM systems showed a highly significant positive correlation between them with a mismatch at 5% for H pylori gastritis. The OLGA and OLGIM staging systems in addition to Sydney System, allow selection of high risk forms of chronic gastritis requiring accurate observation.

Effect of ultrasonic pre-treatment of thermomechanical pulp on hydrogen peroxide bleaching

Science.gov (United States)

Loranger, E.; Charles, A.; Daneault, C.

2012-12-01

Ultrasound pre-treatments of softwood TMP had been carried to evaluate its impact on the efficiency of hydrogen peroxide bleaching. The trials were performed after a factorial design of experiment using frequency, power and time as variables. The experiments were conducted in an ultrasonic bath and then bleached with hydrogen peroxide. Measurements such as brightness, L*A*B* color system coordinate, residual hydrogen peroxide and metal content were evaluated on bleached pulp. The results indicate that the effect of ultrasonic treatment on brightness was dependent on the ultrasound frequency used; the brightness increased slightly at 68 kHz and decreased at 40 and 170 kHz. These results were correlated to the ultrasound effect on the generation of transition metals (copper, iron and manganese) which are responsible for catalytic decomposition of hydrogen peroxide. The influence of metal interference was minimized by using a chelating agent such as diethylene triamine pentaacetic acid (DTPA). With the results obtained in this study we have identified a set of option conditions, e.g. 1000 W, 40 kHz, 1.5 % consistency and 0.2% addition of DTPA prior to the bleaching stage (after ultrasonic pre-treatment) who improve brightness by 2.5 %ISO.

A simplified staging system based on the radiological findings in different stages of ochronotic spondyloarthropathy

International Nuclear Information System (INIS)

Jebaraj, Isaac; Chacko, Binita Riya; Chiramel, George Koshy; Matthai, Thomas; Parameswaran, Apurve

2013-01-01

This study describes a group of 26 patients with ochronotic spondyloarthropathy who were on regular treatment and follow-up at a tertiary level hospital and proposes a simplified staging system for ochronotic spondyloarthropathy based on radiographic findings seen in the thoracolumbar spine. This proposed classification makes it easy to identify the stage of the disease and start the appropriate management at an early stage. Four progressive stages are described: an inflammatory stage (stage 1), the stage of early discal calcification (stage 2), the stage of fibrous ankylosis (stage 3), and the stage of bony ankylosis (stage 4). To our knowledge, this is the largest reported series of radiological description of spinal ochronosis, and emphasizes the contribution of the spine radiograph in the diagnosis and staging of the disease

A simplified staging system based on the radiological findings in different stages of ochronotic spondyloarthropathy

Directory of Open Access Journals (Sweden)

Isaac Jebaraj

2013-01-01

Full Text Available This study describes a group of 26 patients with ochronotic spondyloarthropathy who were on regular treatment and follow-up at a tertiary level hospital and proposes a simplified staging system for ochronotic spondyloarthropathy based on radiographic findings seen in the thoracolumbar spine. This proposed classification makes it easy to identify the stage of the disease and start the appropriate management at an early stage. Four progressive stages are described: an inflammatory stage (stage 1, the stage of early discal calcification (stage 2, the stage of fibrous ankylosis (stage 3, and the stage of bony ankylosis (stage 4. To our knowledge, this is the largest reported series of radiological description of spinal ochronosis, and emphasizes the contribution of the spine radiograph in the diagnosis and staging of the disease.

Optimization of Alkaline and Dilute Acid Pretreatment of Agave Bagasse by Response Surface Methodology

Science.gov (United States)

Ávila-Lara, Abimael I.; Camberos-Flores, Jesus N.; Mendoza-Pérez, Jorge A.; Messina-Fernández, Sarah R.; Saldaña-Duran, Claudia E.; Jimenez-Ruiz, Edgar I.; Sánchez-Herrera, Leticia M.; Pérez-Pimienta, Jose A.

2015-01-01

Utilization of lignocellulosic materials for the production of value-added chemicals or biofuels generally requires a pretreatment process to overcome the recalcitrance of the plant biomass for further enzymatic hydrolysis and fermentation stages. Two of the most employed pretreatment processes are the ones that used dilute acid (DA) and alkaline (AL) catalyst providing specific effects on the physicochemical structure of the biomass, such as high xylan and lignin removal for DA and AL, respectively. Another important effect that need to be studied is the use of a high solids pretreatment (≥15%) since offers many advantaged over lower solids loadings, including increased sugar and ethanol concentrations (in combination with a high solids saccharification), which will be reflected in lower capital costs; however, this data is currently limited. In this study, several variables, such as catalyst loading, retention time, and solids loading, were studied using response surface methodology (RSM) based on a factorial central composite design of DA and AL pretreatment on agave bagasse using a range of solids from 3 to 30% (w/w) to obtain optimal process conditions for each pretreatment. Subsequently enzymatic hydrolysis was performed using Novozymes Cellic CTec2 and HTec2 presented as total reducing sugar (TRS) yield. Pretreated biomass was characterized by wet-chemistry techniques and selected samples were analyzed by calorimetric techniques, and scanning electron/confocal fluorescent microscopy. RSM was also used to optimize the pretreatment conditions for maximum TRS yield. The optimum conditions were determined for AL pretreatment: 1.87% NaOH concentration, 50.3 min and 13.1% solids loading, whereas DA pretreatment: 2.1% acid concentration, 33.8 min and 8.5% solids loading. PMID:26442260

SU-F-T-351: Establishing a Workflow for IMRT Pre-Treatment Reviews for NRG-GY006 Clinical Trial

Energy Technology Data Exchange (ETDEWEB)

Giaddui, T [Sidney Kimmel Cancer Center, Thomas Jefferson University, Philadelphia, PA (United States); Li, N; Moore, K; Mell, L [University of California, San Diego, San Diego, CA (United States); Curry, K [MIM Software, Inc., Clevealand, OH (United States); Leath, C [University of Alabama at Birmingham, Birmingham, AL (United States); Kunos, C [Northeastern Ohio University College, Clevealand, OH (United States); Xiao, Y [University of Pennsylvania, Philadelphia, PA (United States)

2016-06-15

Purpose: To establish a workflow for NRG-GY006 IMRT pre-treatment reviews, incorporating advanced radiotherapy technologies being evaluated as part of the clinical trial. Methods: Pre-Treatment reviews are required for every IMRT case as part of NRG-GY006 (a randomized phase II trial of radiation therapy and cisplatin alone or in combination with intravenous triapine in women with newly diagnosed bulky stage I B2, stage II, IIIB, or IVA cancer of the uterine cervix or stage II-IVA vaginal cancer. The pretreatment review process includes structures review and generating an active bone marrow(ABM)- to be used as an avoidance structure during IMRT optimization- and evaluating initial IMRT plan quality using knowledgeengineering based planning (KBP). Institutions will initially submit their simulation CT scan, structures file and PET/CT to IROC QA center for generating ABM. The ABM will be returned to the institution for use in planning. Institutions will then submit an initial IMRT plan for review and will receive information back following implementation of a KBP algorithm, for use in re-optimization, before submitting the final IMRT used for treatment. Results: ABM structure is generated using MIM vista software (Version 6.5, MIM corporation, Inc.). Here, the planning CT and the diagnostic PET/CT are fused and a sub threshold structure is auto segmented above the mean value of the SUV of the bone marrow. The generated ABM were compared with those generated with other software system (e.g. Velocity, Varian) and Dice coefficient (reflects the overlap of structures) ranged between 80 – 90% was achieved. A KBP model was built in Varian Eclipse TPS using the RapidPlan KBP software to perform plan quality assurance. Conclusion: The workflow for IMRT pretreatment reviews has been established. It represents a major improvement of NRG Oncology clinical trial quality assurance and incorporates the latest radiotherapy technologies as part of NCI clinical trials. This project

SU-F-T-351: Establishing a Workflow for IMRT Pre-Treatment Reviews for NRG-GY006 Clinical Trial

International Nuclear Information System (INIS)

Giaddui, T; Li, N; Moore, K; Mell, L; Curry, K; Leath, C; Kunos, C; Xiao, Y

2016-01-01

Purpose: To establish a workflow for NRG-GY006 IMRT pre-treatment reviews, incorporating advanced radiotherapy technologies being evaluated as part of the clinical trial. Methods: Pre-Treatment reviews are required for every IMRT case as part of NRG-GY006 (a randomized phase II trial of radiation therapy and cisplatin alone or in combination with intravenous triapine in women with newly diagnosed bulky stage I B2, stage II, IIIB, or IVA cancer of the uterine cervix or stage II-IVA vaginal cancer. The pretreatment review process includes structures review and generating an active bone marrow(ABM)- to be used as an avoidance structure during IMRT optimization- and evaluating initial IMRT plan quality using knowledgeengineering based planning (KBP). Institutions will initially submit their simulation CT scan, structures file and PET/CT to IROC QA center for generating ABM. The ABM will be returned to the institution for use in planning. Institutions will then submit an initial IMRT plan for review and will receive information back following implementation of a KBP algorithm, for use in re-optimization, before submitting the final IMRT used for treatment. Results: ABM structure is generated using MIM vista software (Version 6.5, MIM corporation, Inc.). Here, the planning CT and the diagnostic PET/CT are fused and a sub threshold structure is auto segmented above the mean value of the SUV of the bone marrow. The generated ABM were compared with those generated with other software system (e.g. Velocity, Varian) and Dice coefficient (reflects the overlap of structures) ranged between 80 – 90% was achieved. A KBP model was built in Varian Eclipse TPS using the RapidPlan KBP software to perform plan quality assurance. Conclusion: The workflow for IMRT pretreatment reviews has been established. It represents a major improvement of NRG Oncology clinical trial quality assurance and incorporates the latest radiotherapy technologies as part of NCI clinical trials. This project

Enhancing organic matter removal in desalination pretreatment systems by application of dissolved air flotation

DEFF Research Database (Denmark)

Shutova, Yulia; Karna, Barun Lal; Hambly, Adam C.

2016-01-01

on the sample, respectively. The optimal normalised coagulant dose (Fe3+ to DOC ratio) was observed to be 0.5-4 at pH5.5 increasing to 4-12 at pH7.5. At pH5.5, the optimum coagulant dose increased with increasing humic character of the feed water. Overall, the OM removal efficiency by DAF observed in this study......Membrane fouling in reverse osmosis (RO) systems caused by organic matter (OM) remains a significant operational issue during desalination. Dissolved air flotation (DAF) has recently received attention as a pre-treatment option for seawater OM removal; however, only a limited number of studies have...... been undertaken. This may be because it is difficult to characterise OM in seawater due to the high salt content and low carbon concentration. In this study, DAF pre-treatment experiments were conducted using a model seawater solution, and real seawater and brackish water samples. DAF performance...

Nonhazardous Urine Pretreatment Method for Future Exploration Systems, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — A novel urine pretreatment that will prevent biological growth or chemical instabilities in urine without using hazardous chemicals is proposed. Untreated urine...

Ultrasonic and Thermal Pretreatments on Anaerobic Digestion of Petrochemical Sludge: Dewaterability and Degradation of PAHs

Science.gov (United States)

Zhou, Jun; Xu, Weizhong; Wong, Jonathan W. C.; Yong, Xiaoyu; Yan, Binghua; Zhang, Xueying; Jia, Honghua

2015-01-01

Effects of different pretreatment methods on sludge dewaterability and polycyclic aromatic hydrocarbons (PAHs) degradation during petrochemical sludge anaerobic digestion were studied. Results showed that the total biogas production volume in the thermal pretreatment system was 4 and 5 times higher than that in the ultrasound pretreatment and in the control system, and the corresponding volatile solid removal efficiencies reached 28%, 15%, and 8%. Phenanthrene, paranaphthalene, fluoranthene, benzofluoranthene, and benzopyrene removal rates reached 43.3%, 55.5%, 30.6%, 42.9%, and 41.7%, respectively, in the thermal pretreatment system, which were much higher than those in the ultrasound pretreatment and in the control system. Moreover, capillary suction time (CST) of sludge increased after pretreatment, and then reduced after 20 days of anaerobic digestion, indicating that sludge dewaterability was greatly improved after anaerobic digestion. The decrease of protein and polysaccharide in the sludge could improve sludge dewaterability during petrochemical sludge anaerobic digestion. This study suggested that thermal pretreatment might be a promising enhancement method for petrochemical sludge solubilization, thus contributing to degradation of the PAHs, biogas production, and improvement of dewaterability during petrochemical sludge anaerobic digestion. PMID:26327510

Sequential pretreatment for cell disintegration of municipal sludge in a neutral Bio-electro-Fenton system.

Science.gov (United States)

Yu, Qilin; Jin, Xiaochen; Zhang, Yaobin

2018-05-15

Sludge cell disruption was generally considered as the rate-limiting step for the anaerobic digestion of waste activated sludge (WAS). Advanced oxidation processes and bio-electro-chemical systems were recently reported to enhance the hydrolysis of WAS and sludge cell disruption, while the cell-breaking processes of these systems remain unclear yet. In this study, an innovative Bio-electro-Fenton system was developed to pretreat the WAS sequentially with cathode Fenton process and anode anaerobic digestion. Significant cell disruption and dissolution intracellular organics were founded after the treatment. X-ray photoelectron spectroscopy (XPS) analysis and fourier transform infrared spectroscopy (FT-IR) spectra indicated that Gram-negative bacteria were more sensitive to free radicals yielded in cathode to induce a chain reaction that destroyed the lipid-contained outer membrane, while Gram-positive bacteria with thick peptidoglycan layer were liable to be biologically decomposed in the anode. Compared with the oxidation of organic matters in the cathode Fenton, the secretion of enzyme increased in the anode which was beneficial to break down the complex matters (peptidoglycans) into simples that were available for anode oxidation by exoelectrogens. The results also showed a possible prospect for the application of this sequential pretreatment in bio-electro-Fenton systems to disrupt sludge cells and enhance the anaerobic digestion. Copyright © 2018 Elsevier Ltd. All rights reserved.

Validation of the CPS + EG Staging System for Disease-Specific Survival in Breast Cancer Patients Treated with Neoadjuvant Chemotherapy.

Science.gov (United States)

Abdelsattar, Jad M; Al-Hilli, Zahraa; Hoskin, Tanya L; Heins, Courtney N; Boughey, Judy C

2016-10-01

CPS + EG staging, which incorporates estrogen receptor (ER) status and tumor grade with pretreatment clinical stage (CS) and post-treatment pathologic stage (PS), has been reported to have better correlation with outcome than classic TNM staging for patients treated with neoadjuvant chemotherapy (NAC). Our goal was to evaluate the performance of CPS + EG staging system in an external cohort treated with NAC. We reviewed patients with stages I-IIIC breast cancer treated with NAC and surgery at our institution between 1988 and 2014. ER status, Nottingham grade, treatment, American Joint Committee on Cancer (AJCC) CS before NAC and PS after NAC, and follow-up data were collected. The discrimination of CPS + EG and pathologic AJCC stage were assessed using area under the curve (AUC) for survival data. A total of 769 patients were analyzed with a median follow-up of 2.6 (range 0.0-19.4) years; 103 patients died of breast cancer. Overall, the 5-year breast cancer cause-specific survival was 81.5 % [95 % confidence interval (CI) 77.6-85.5]. The 5-year, cause-specific survival by CPS + EG score was 93.8 % score 0, 89.9 % score 1, 90.7 % score 2, 84.8 % score 3, 67.7 % score 4, and 43.4 % score 5/6. CPS + EG score was significantly associated with cause-specific survival (p < 0.001) with an AUC of 0.69 (95 % CI 0.62-0.77) at 5 years. This was higher than the AUC of 0.63 (95 % CI 0.56-0.70) for AJCC PS (p = 0.10). This study validates the CPS + EG staging system using Nottingham grade in an external cohort. Addition of tumor biology and treatment response shows promise in improving survival estimates for patients treated with NAC.

Furfural production from biomass pretreatment hydrolysate using vapor-releasing reactor system.

Science.gov (United States)

Liu, Lu; Chang, Hou-Min; Jameel, Hasan; Park, Sunkyu

2018-03-01

Biomass hydrolysate from autohydrolysis pretreatment was used for furfural production considering it is in rich of xylose, xylo-oligomers, and other decomposition products from hemicellulose structure. By using the vapor-releasing reactor system, furfural was protected from degradation by separating it from the reaction media. The maximum furfural yield of 73% was achieved at 200 °C for biomass hydrolysate without the use of the catalyst. This is because the presence of organic acids such as acetic acid in hydrolysate functioned as a catalyst. According to the results in this study, biomass hydrolysate with a vapor-releasing system proves to be efficient for furfural production. The biorefinery process which allows the separation of xylose-rich autohydrolysate from other parts from biomass feedstock also improves the overall application of the biomass. Copyright © 2018 Elsevier Ltd. All rights reserved.

Enhancement of biogas production in anaerobic co-digestion by ultrasonic pretreatment

International Nuclear Information System (INIS)

Zou, Shuzhen; Wang, Xiaojiao; Chen, Yuanlin; Wan, Haiwen; Feng, Yongzhong

2016-01-01

Highlights: • Ultrasonic pretreatment changed physical structure of samples. • Ultrasonic pretreatment improved biogas production via changing environment before and during anaerobic digestion process. • The main factors affecting biogas production differ in different pretreated samples. - Abstract: This paper optimized the anaerobic digestion (AD) pretreatment process and identified the influence of pretreatment on the co-digestion of maize straw (MS) and dairy manure (DM). In the study, ultrasonic was used to pretreat MS and DM prior to digestion, with power intensities of 0, 189.39, 284.09, and 378.79 kJ at 0, 20, 30, and 40 min, respectively. Changes in the surface structures of MS and DM were observed by scanning electron microscopy (SEM), and factor analysis was used to analyze the main factors affecting biogas production in the AD process. The result showed that the structure of DM was distributed and that the structure of MS became more roughness following the ultrasonic pretreatment (UP). The highest total biogas production of co-digestion (240.32 mL/g VS_f_e_d) was obtained when MS was pretreated for 30 min without DM pretreatment (MS_3_0DM_0). This was significantly higher than that of the untreated sample (CK) (141.65 mL/g VS_f_e_d). The cellulose activity (CA), reducing sugar (RS) content, volatile fatty acid (VFA) content and pH in the digester feed, and their maximum and minimum values in the AD process was affected by UP. Factor 1 of MS_3_0DM_0 was determined by RS content, pH and VFA content that they had the most influence on biogas production on days 6, 18, 24 and 30. Factor 2 of it was determined by CA, and it had most influence on days 0, 12, 36 and 42 in the AD process, The result of the factor analysis indicated that the main factors affecting biogas production were affected by UP and they differ according to the different digestion stages. This research concluded that UP improved total biogas production via changing the initial

Degumming Pretreatment with Sodium Hydroxide and Sodium Oxalate in the Process of Whole Cotton Stalk APMP Pulping

Directory of Open Access Journals (Sweden)

Yu-Meng Zhao

2015-03-01

Full Text Available The effect of degumming pretreatment on whole cotton stalk alkaline peroxide mechanical pulp (APMP was researched. Degumming pretreatment was used as the first stage of an APMP pulping process, replacing conventional hot water pretreatment. Two degumming agents of sodium hydroxide (NaOH and sodium oxalate (Na2C2O4 were researched separately. The efficiency of hot water pretreatment, NaOH pretreatment, and Na2C2O4 pretreatment on pectin and metal ions removal was compared. After pretreatment of hot water, NaOH, and Na2C2O4, pectin content was reduced to 4.0%, 2.1%, 1.6%, respectively, compared to original material (4.3%, at removal rates of 7%, 51%, and 64%, respectively. For metal ions, especially transition metal ions, the removal rate was up to 20% after degumming pretreatment. The brightness of the handsheets was 64% ISO, 68% ISO, and 73% ISO, respectively. The dirt count was 2674 mm2•m-2, 533 mm2•m-2, and 132 mm2•m-2, respectively. After Na2C2O4 pretreatment, the tension index and tear index were increased to 40.5 N•m•g-1 and 4.5 mN•m2•g-1, respectively. Through degumming pretreatment, pectin, metal ions, and dirt count were reduced efficiently, and the brightness and physical strength were improved significantly.

Impact of tumor attachment to the pleura measured by a pretreatment CT image on outcome of stage I NSCLC treated with stereotactic body radiotherapy

International Nuclear Information System (INIS)

Yamamoto, Takaya; Kadoya, Noriyuki; Shirata, Yuko; Koto, Masashi; Sato, Kiyokazu; Matsushita, Haruo; Sugawara, Toshiyuki; Umezawa, Rei; Kubozono, Masaki; Ishikawa, Yojiro; Kozumi, Maiko; Takahashi, Noriyoshi; Ito, Kengo; Katagiri, Yu; Takeda, Ken; Jingu, Keiichi

2015-01-01

Pleural invasion status is known to be a predictor of survival after pulmonary resection for non-small cell lung cancer. Our goal was to determine whether the length of tumor attachment to the pleura on a pretreatment CT image has prognostic value as an alternative to pleural invasion status for stage I non-small cell lung cancer treated with stereotactic body radiotherapy (SBRT). A total of 90 tumors in 87 patients (males: 68, females: 19) who received SBRT between March 2005 and September 2011 in our institution were reviewed. The median age of the patients was 78 years (range, 48-90 years). The median tumor diameter was 2.2 cm (range, 0.9-4.2 cm). The prescribed dose was typically 48 Gy in 4 fractions, 60 Gy in 8 fractions or 60 Gy in 15 fractions to the isocenter with 6 MV X-ray using 4 non-coplanar and 3 coplanar static beams. The lengths of attachment were measured using pretreatment CT images at the lung window. Cumulative incidence rates were calculated using Kaplan-Meier curves, and univariate and multivariate analyses for in-field tumor control, locoregional control (LRC), freedom from distant metastasis and freedom from progression (FFP) were performed using a Cox proportional hazards model. Of the 90 tumors, 42 tumors were attached to the pleura (median, 14.7 mm; range, 4.3-36.0 mm), 21 tumors had pleural indentation and 27 tumors had no attachment. The median follow-up period for survivors was 46.1 months. The 3-year in-field control, LRC, FFP and overall survival rates were 91.2%, 75.3%, 63.8% and 68.6%, respectively. SBRT dose and tumor diameter were independently significant predictors of in-field control (p = 0.02 and p = 0.04, respectively). Broad attachment to the pleura, the length being more than 14.7 mm, was a negative independent predictor of LRC and FFP (p = 0.02 and p = 0.01, respectively). Pleural attachment status on a pretreatment CT image might be an important predictor of LRC and FFP

Suppressive versus augmenting effect of the same pretreatment regimen in two murine tumor systems with distinct effector mechanisms

International Nuclear Information System (INIS)

Fujiwara, Hiromi; Hamaoka, Toshiyuki; Kitagawa, Masayasu

1978-01-01

The effect of presensitization with x-irradiated tumor cells on the development of host's immune resistance against the tumor-associated transplantation antigens (TATA) was investigated in two syngeneic tumor systems with distinct effector mechanisms. When X5563 plasmacytoma, to which immune resistance was mediated exclusively by killer T lymphocytes, was intravenously inoculated into syngeneic C3H/He mice with lower number after 7000 R x-irradiation, the mice failed to exhibit any protective immunity against the subsequent challenge with viable tumor cells. Moreover, these mice lost their capability to develop any immune resistance even after an appropriate immunization procedure. The immunodepression induced by such a pretreatment regimen was specific for X5563 tumor. While no suppressor cell activity was detected in the above pretreated mice, serum factor(s) from these mice was virtually responsible for this suppression. When the serum factor mediating this tumor-specific suppression was fractionated on the Sephadex G-200 column, the suppressive activity was found in albumin-corresponding fraction, free of any immunoglobulin component. In contrast, in MM102 mammary tumor system, in which immune resistance is solely mediated by tumor-specific antibody, the pretreatment with x-irradiated MM102 cells augmented the induction of anti-tumor immunity. These results indicate that while tumor antigens given in the form of x-irradiated tumor cells suppress the induction of killer T cell-mediated immunity in one system, the same presensitization regimen of tumor antigens augments the antibody-mediated immunity in another system, thus giving a divergent effect on the distinct effector mechanisms of syngeneic tumor immunity. (author)

Lignocellulosic Biomass Pretreatment Using AFEX

Science.gov (United States)

Balan, Venkatesh; Bals, Bryan; Chundawat, Shishir P. S.; Marshall, Derek; Dale, Bruce E.

Although cellulose is the most abundant organic molecule, its susceptibility to hydrolysis is restricted due to the rigid lignin and hemicellulose protection surrounding the cellulose micro fibrils. Therefore, an effective pretreatment is necessary to liberate the cellulose from the lignin-hemicellulose seal and also reduce cellulosic crystallinity. Some of the available pretreatment techniques include acid hydrolysis, steam explosion, ammonia fiber expansion (AFEX), alkaline wet oxidation, and hot water pretreatment. Besides reducing lignocellulosic recalcitrance, an ideal pretreatment must also minimize formation of degradation products that inhibit subsequent hydrolysis and fermentation. AFEX is an important pretreatment technology that utilizes both physical (high temperature and pressure) and chemical (ammonia) processes to achieve effective pretreatment. Besides increasing the surface accessibility for hydrolysis, AFEX promotes cellulose decrystallization and partial hemicellulose depolymerization and reduces the lignin recalcitrance in the treated biomass. Theoretical glucose yield upon optimal enzymatic hydrolysis on AFEX-treated corn stover is approximately 98%. Furthermore, AFEX offers several unique advantages over other pretreatments, which include near complete recovery of the pretreatment chemical (ammonia), nutrient addition for microbial growth through the remaining ammonia on pretreated biomass, and not requiring a washing step during the process which facilitates high solid loading hydrolysis. This chapter provides a detailed practical procedure to perform AFEX, design the reactor, determine the mass balances, and conduct the process safely.

Cost comparison for REDC pretreatment project

International Nuclear Information System (INIS)

Robinson, S.M.; Homan, F.J.

1997-06-01

This analysis has been prepared to support the planned expenditure to provide the Radiochemical Engineering Development Center (REDC) with the capability to pretreat their liquid low-level waste (LLLW) before discharging it to the Oak Ridge National Laboratory (ORNL) LLLW system. Pretreatment will remove most of the radioactivity, particularly the transuranic isotopes and Cs-137 from the waste to be discharged. This will render the supernates that accumulate in the storage tanks low-activity Class B low-level wastes rather than high-activity Class B or Class C wastes. The sludges will be Class C rather than remote-handled transuranic (RH-TRU) wastes. When REDC wastes are commingled with other ORNL LLLW, the present-worth treatment and transport costs are higher by a factor of 1.3 for the no-pretreatment cases. This result is consistent with data from similar studies conducted at other sites. Based on the information presented in this analysis, the recommendation is to proceed with REDC treatment projects

Negative impact of pretreatment anemia on local control after neoadjuvant chemoradiotherapy and surgery for rectal cancer

Energy Technology Data Exchange (ETDEWEB)

Lee, Hye Bin; Park, Hee Chul; Park, Won [Samsung Medical Center, Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of); and others

2012-09-15

Although anemia is considered to be a contributor to intra-tumoral hypoxia and tumor resistance to ionizing radiation in cancer patients, the impact of pretreatment anemia on local control after neoadjuvant concurrent chemoradiotherapy (NACRT) and surgery for rectal cancer remains unclear. We reviewed the records of 247 patients with locally advanced rectal cancer who were treated with NACRT followed by curative-intent surgery. The patients with anemia before NACRT (36.0%, 89/247) achieved less pathologic complete response (pCR) than those without anemia (p = 0.012). The patients with pretreatment anemia had worse 3-year local control than those without pretreatment anemia (86.0% vs. 95.7%, p = 0.005). Multivariate analysis showed that pretreatment anemia (p = 0.035), pathologic tumor and nodal stage (p = 0.020 and 0.032, respectively) were independently significant factors for local control. Pretreatment anemia had negative impacts on pCR and local control among patients who underwent NACRT and surgery for rectal cancer. Strategies maintaining hemoglobin level within normal range could potentially be used to improve local control in rectal cancer patients.

Negative impact of pretreatment anemia on local control after neoadjuvant chemoradiotherapy and surgery for rectal cancer

International Nuclear Information System (INIS)

Lee, Hye Bin; Park, Hee Chul; Park, Won

2012-01-01

Although anemia is considered to be a contributor to intra-tumoral hypoxia and tumor resistance to ionizing radiation in cancer patients, the impact of pretreatment anemia on local control after neoadjuvant concurrent chemoradiotherapy (NACRT) and surgery for rectal cancer remains unclear. We reviewed the records of 247 patients with locally advanced rectal cancer who were treated with NACRT followed by curative-intent surgery. The patients with anemia before NACRT (36.0%, 89/247) achieved less pathologic complete response (pCR) than those without anemia (p = 0.012). The patients with pretreatment anemia had worse 3-year local control than those without pretreatment anemia (86.0% vs. 95.7%, p = 0.005). Multivariate analysis showed that pretreatment anemia (p = 0.035), pathologic tumor and nodal stage (p = 0.020 and 0.032, respectively) were independently significant factors for local control. Pretreatment anemia had negative impacts on pCR and local control among patients who underwent NACRT and surgery for rectal cancer. Strategies maintaining hemoglobin level within normal range could potentially be used to improve local control in rectal cancer patients.

Mass loss controlled thermal pretreatment system to assess the effects of pretreatment temperature on organic matter solubilization and methane yield from food waste.

Directory of Open Access Journals (Sweden)

Martha Minale Yeshanew

2016-09-01

Full Text Available The effects of thermal pretreatment (TP on the main characteristics of food waste (FW and its biochemical methane potential (BMP and distribution of volatile fatty acids (VFAs under mesophilic condition (35 ⁰C were investigated. The TP experiments were carried out at 80 °C, 100 °C, 120 °C for 2 hour and 140 °C for 1 hour. The designed TP set-up was able to minimize the organic matter loss during the course of the pretreatments. Soluble organic fractions evaluated in terms of chemical oxygen demand (COD and soluble protein increased linearly with pretreatment temperature. In contrast, the carbohydrate solubilization was more enhanced (30 % higher solubilization by the TP at lower temperature (80 °C. A slight increment of soluble phenols was found, particularly for temperatures exceeding 100 °C. Thermally pretreated FW under all conditions exhibited an improved methane yield than the untreated FW, due to the increased organic matter solubilization. The highest cumulative methane yield of 442 (± 8.6 mL/gVSadded, corresponding to a 28.1 % enhancement compared to the untreated FW, was obtained with a TP at 80 °C. No significant variation in the VFAs trends were observed during the BMP tests under all investigated conditions.

Catalytic conversion of corncob and corncob pretreatment hydrolysate to furfural in a biphasic system with addition of sodium chloride.

Science.gov (United States)

Qing, Qing; Guo, Qi; Zhou, Linlin; Wan, Yilun; Xu, Youqing; Ji, Huilong; Gao, Xiaohang; Zhang, Yue

2017-02-01

Catalytic conversion of corncob pretreatment hydrolysate and raw corncob into furfural in a modified biphasic system by SO 4 2- /SnO 2 - MMT solid catalyst has been developed. The influence of the organic solvent type, organic to water phase ratio, sodium chloride concentration, reaction temperature and time on the furfural production were comparatively evaluated. The results showed that furfural yields of 81.7% and 66.1% were achieved at 190°C for 15mins and 190°C for 20mins, respectively, for corncob pretreatment hydrolysate and raw corncob by this solid catalyst. The solid catalyst used in this study exhibited good stability and high efficiency applied in the modified biphasic system in addition to excellent recyclability. The proposed catalytic system displayed high performance for catalytic conversion of lignocellulosic biomass into important platform chemicals and has great potential in industrial application. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pretreatment of the macroalgae Chaetomorpha linum for the production of bioethanol - Comparison of five pretreatment technologies

DEFF Research Database (Denmark)

Schultz-Jensen, Nadja; Thygesen, Anders; Thomsen, Sune Tjalfe

2013-01-01

-assisted pretreatment (PAP) and ball milling (BM), to determine effects of the pretreatment methods on the conversion of C. linum into ethanol by simultaneous saccharification and fermentation (SSF). WO and BM showed the highest ethanol yield of 44. g ethanol/100. g glucan, which was close to the theoretical ethanol......A qualified estimate for pretreatment of the macroalgae Chaetomorpha linum for ethanol production was given, based on the experience of pretreatment of land-based biomass. C. linum was subjected to hydrothermal pretreatment (HTT), wet oxidation (WO), steam explosion (STEX), plasma...... yield of 57. g ethanol/100. g glucan. A 64% higher ethanol yield, based on raw material, was reached after pretreatment with WO and BM compared with unpretreated C. linum, however 50% of the biomass was lost during WO. Results indicated that the right combination of pretreatment and marine macroalgae...

Tank waste pretreatment issues, alternatives and strategies for resolution

International Nuclear Information System (INIS)

Miller, W.C.; Appel, J.; Barton, W.B.; Orme, R.M.; Holton, L.K. Jr.

1993-02-01

The US Department of Energy (DOE) has established the Tank Waste Remediation System (TWRS) to safely manage and dispose of the Hanford Site tank waste. The overall strategy for disposing of tank waste is evolving and initial recommendations on a course of action are expected in March, 1993. Pretreatment of these wastes may be required for one or both of the following reasons: (1) resolution of tank safety issues, and (2) preparation of low level and high level waste fractions for disposal. Pretreatment is faced with several issues that must be addressed by the deployment strategies that are being formulated. These issues are identified. There is also a discussion of several pretreatment deployment strategies and how these strategies address the issues. Finally, the technology alternatives that are being considered for the pretreatment function are briefly discussed

Pretreatment of corn stover for sugar production using dilute hydrochloric acid followed by lime.

Science.gov (United States)

Zu, Shuai; Li, Wen-zhi; Zhang, Mingjian; Li, Zihong; Wang, Ziyu; Jameel, Hasan; Chang, Hou-min

2014-01-01

In this study, a two stage process was evaluated to increase the sugar recovery. Firstly, corn stover was treated with diluted hydrochloric acid to maximize the xylose yield, and then the residue was treated with lime to alter the lignin structure and swell the cellulose surface. The optimal condition was 120 °C and 40 min for diluted hydrochloric acid pretreatment followed by lime pretreatment at 60 °C for 12h with lime loading at 0.1 g/g of substrate. The glucose and xylose yield was 78.0% and 97.0%, respectively, with cellulase dosage at 5 FPU/g of substrate. The total glucose yield increased to 85.9% when the cellulase loading was increased to 10 FPU/g of substrate. This two stage process was effective due to the swelling of the internal surface, an increase in the porosity and a decrease in the degree of polymerization. Copyright © 2013 Elsevier Ltd. All rights reserved.

Attainability and minimum energy of multiple-stage cascade membrane Systems

KAUST Repository

Alshehri, Ali

2015-08-12

Process design and simulation of multi-stage membrane systems have been widely studied in many gas separation systems. However, general guidelines have not been developed yet for the attainability and the minimum energy consumption of a multi-stage membrane system. Such information is important for conceptual process design and thus it is the topic of this work. Using a well-mixed membrane model, it was determined that the attainability curve of multi-stage systems is defined by the pressure ratio and membrane selectivity. Using the constant recycle ratio scheme, the recycle ratio can shift the attainability behavior between single-stage and multi-stage membrane systems. When the recycle ratio is zero, all of the multi-stage membrane processes will decay to a single-stage membrane process. When the recycle ratio approaches infinity, the required selectivity and pressure ratio reach their absolute minimum values, which have a simple relationship with that of a single-stage membrane process, as follows: View the MathML sourceSn=S1, View the MathML sourceγn=γ1, where n is the number of stages. The minimum energy consumption of a multi-stage membrane process is primarily determined by the membrane selectivity and recycle ratio. A low recycle ratio can significantly reduce the required membrane selectivity without substantial energy penalty. The energy envelope curve can provide a guideline from an energy perspective to determine the minimum required membrane selectivity in membrane process designs to compete with conventional separation processes, such as distillation.

Lignocellulose fractionation into furfural and glucose by AlCl3-catalyzed DES/MIBK biphasic pretreatment.

Science.gov (United States)

Wang, Zhi-Kun; Shen, Xiao-Jun; Chen, Jun-Jie; Jiang, Ying-Qiu; Hu, Zhi-Yan; Wang, Xing; Liu, Li

2018-06-01

Herein, an efficient DES/MIBK biphasic pretreatment system for preparation of furfural and fermentable glucose from lignocellulose was developed with AlCl 3 as catalysis. The low-cost and renewable DES (Choline chloride-Oxalic acid) served not only as a Brønsted acid catalyst, but also as a pretreatment solvent in present work, and MIBK as an extracting reagent which can increase the yield of furfural in DES phase. The effects of this biphasic pretreatment on the furfural yield and saccharification of the lignocellulose before and after pretreatment were explored using HPLC, HAPEC, FT-IR, XRD and SEM. Under the best pretreatment condition (at 140 °C for 90 min), furfural could be obtained in 70.3% yield and 80.8% of the pretreated lignocellulose was saccharified, which was 8.4 times higher than that of the raw lignocellulose without pretreatment. In a word, this pretreatment system can be considered as a potential technique for efficient valorization of lignocellulose for production of furfural and fermentable glucose. Copyright © 2018. Published by Elsevier B.V.

Performance of an effectively integrated biomass multi-stage gasification system and a steel industry heat treatment furnace

International Nuclear Information System (INIS)

Gunarathne, Duleeka Sandamali; Mellin, Pelle; Yang, Weihong; Pettersson, Magnus; Ljunggren, Rolf

2016-01-01

Highlights: • Multi-stage biomass gasification is integrated with steel heat treatment furnace. • Fossil fuel derived CO_2 emission is eliminated by replacing natural gas with syngas. • The integrated system uses waste heat from the furnace for biomass gasification. • Up to 13% increment of the gasifier system energy efficiency is observed. • Fuel switching results in 10% lower flue gas loss and improved furnace efficiency. - Abstract: The challenges of replacing fossil fuel with renewable energy in steel industry furnaces include not only reducing CO_2 emissions but also increasing the system energy efficiency. In this work, a multi-stage gasification system is chosen for the integration with a heat treatment furnace in the steel powder industry to recover different rank/temperature waste heat back to the biomass gasification system, resulting higher system energy efficiency. A system model based on Aspen Plus was developed for the proposed integrated system considering all steps, including biomass drying, pyrolysis, gasification and the combustion of syngas in the furnace. Both low temperature (up to 400 °C) and high temperature (up to 700 °C) heat recovery possibilities were analysed in terms of energy efficiency by optimizing the biomass pretreatment temperature. The required process conditions of the furnace can be achieved by using syngas. No major changes to the furnace, combustion technology or flue gas handling system are necessary for this fuel switching. Only a slight revamp of the burner system and a new waste heat recovery system from the flue gases are required. Both the furnace efficiency and gasifier system efficiency are improved by integration with the waste heat recovery. The heat recovery from the hot furnace flue gas for biomass drying and steam superheating is the most promising option from an energy efficiency point of view. This option recovers two thirds of the available waste heat, according to the pinch analysis performed

Association between pretreatment Glasgow prognostic score and gastric cancer survival and clinicopathological features: a meta-analysis

Directory of Open Access Journals (Sweden)

Zhang CX

2016-06-01

Full Text Available Chun-Xiao Zhang,* Shu-Yi Wang,* Shuang-Qian Chen, Shuai-Long Yang, Lu Wan, Bin Xiong Department of Oncology, Zhongnan Hospital of Wuhan University, Hubei Key Laboratory of Tumor Biological Behaviors and Hubei Cancer Clinical Study Center, Wuhan, Hubei, People’s Republic of China *These authors contributed equally to this work Background: Glasgow prognostic score (GPS is widely known as a systemic inflammatory-based marker. The relationship between pretreatment GPS and gastric cancer (GC survival and clinicopathological features remains controversial. The aim of the study was to conduct a meta-analysis of published studies to evaluate the association between pretreatment GPS and survival and clinicopathological features in GC patients. Methods: We searched PubMed, Embase, MEDLINE, and BioMed databases for relevant studies. Combined analyses were used to assess the association between pretreatment GPS and overall survival, disease-free survival, and clinicopathological parameters by Stata Version 12.0. Results: A total of 14 studies were included in this meta-analysis, including 5,579 GC patients. The results indicated that pretreatment high GPS (HGPS predicted poor overall survival (hazard ratio =1.51, 95% CI: 1.37–1.66, P<0.01 and disease-free survival (hazard ratio =1.45, 95% CI: 1.26–1.68, P<0.01 in GC patients. Pretreatment HGPS was also significantly associated with advanced tumor–node–metastasis stage (odds ratio [OR] =3.09, 95% CI: 2.11–4.53, P<0.01, lymph node metastasis (OR =4.60, 95% CI: 3.23–6.56, P<0.01, lymphatic invasion (OR =3.04, 95% CI: 2.00–4.62, P<0.01, and venous invasion (OR =3.56, 95% CI: 1.81–6.99, P<0.01. Conclusion: Our meta-analysis indicated that pretreatment HGPS could be a predicative factor of poor survival outcome and clinicopathological features for GC patients. Keywords: Glasgow prognostic score, gastric cancer, survival, clinicopathological feature

Enzymatic hydrolsis of pretreated rice straw

Energy Technology Data Exchange (ETDEWEB)

Vlasenko, E.Y.; Shoemaker, S.P. [California Inst. of Food and Agricultural Research, Davis, CA (United States); Ding, H. [California Univ., Davis (Canada). Dept. of Food Science and Technology; Labavitch, J.M. [California Univ., Davis, CA (United States). Dept. of Pomology

1997-02-01

California rice straw is being evaluated as a feedstock for production of power and fuel. This paper examines the initial steps in the process: pretreatment of rice straw and enzymatic hydrolysis of the polysaccharides in the pretreated material to soluble sugars. Rice straw was subjected to three distinct pretreatment procedures: acid-catalyzed steam explosion (Swan Biomass Company), acid hydrolysis (U.S. DOE National Renewable Energy Laboratory), and ammonia fiber explosion or AFEX (Texas A and M University). Standard conditions for each pretreatment were used, but none was optimized for rice straw specifically. Six commercial cellulases, products of Genencor International (USA), Novo (Denmark), Iogen (Canada) and Fermtech (Russia) were used for hydrolysis. The Swan- and the acid-pretreatments effectively removed hemicellulose from rice straw, providing high yields of fermentable sugars. The AFEX-pretreatment was distinctly different from other pretreatments in that it did not significantly solubilize hemicellulose. All three pretreatment procedures substantially increased enzymatic digestibility of rice straw. Three commercial Trichoderma-reesei-derived enzyme preparations: Cellulase 100L (Iogen), Spezyme CP (Genencor), and Al (Fermtech), were more active on pretreated rice straw compared than others tested. Conditions for hydrolysis of rice straw using Cellulase 100L were evaluated. The supplementation of this enzyme preparation with cellobiase (Novozyme 188) significantly improved the parameters of hydrolysis for the Swan- and the acid-pretreated materials, but did not affect the hydrolysis of the AFEX-pretreated rice straw. (Author)

High temperature dilute phosphoric acid pretreatment of corn stover for furfural and ethanol production

Science.gov (United States)

Furfural was produced from corn stover by one stage pretreatment process using dilute H3PO4 and solid residues following furfural production were used for ethanol production by Saccharomyces cerevisiae NRRL- Y2034. A series of experiments were conducted at varied temperatures (140-200 oC) and acid ...

Revised National Pressure Ulcer Advisory Panel Pressure Injury Staging System: Revised Pressure Injury Staging System.

Science.gov (United States)

Edsberg, Laura E; Black, Joyce M; Goldberg, Margaret; McNichol, Laurie; Moore, Lynn; Sieggreen, Mary

Our understanding of pressure injury etiology and development has grown in recent years through research, clinical expertise, and global interdisciplinary expert collaboration. Therefore, the National Pressure Ulcer Advisory Panel (NPUAP) has revised the definition and stages of pressure injury. The revision was undertaken to incorporate the current understanding of the etiology of pressure injuries, as well as to clarify the anatomical features present or absent in each stage of injury. An NPUAP-appointed Task Force reviewed the literature and created drafts of definitions, which were then reviewed by stakeholders and the public, including clinicians, educators, and researchers around the world. Using a consensus-building methodology, these revised definitions were the focus of a multidisciplinary consensus conference held in April 2016. As a result of stakeholder and public input, along with the consensus conference, important changes were made and incorporated into the new staging definitions. The revised staging system uses the term injury instead of ulcer and denotes stages using Arabic numerals rather than Roman numerals. The revised definition of a pressure injury now describes the injuries as usually occurring over a bony prominence or under a medical or other device. The revised definition of a Stage 2 pressure injury seeks to clarify the difference between moisture-associated skin damage and injury caused by pressure and/or shear. The term suspected has been removed from the Deep Tissue Pressure Injury diagnostic label. Each definition now describes the extent of tissue loss present and the anatomical features that may or may not be present in the stage of injury. These important revisions reflect the methodical and collaborative approach used to examine the available evidence and incorporate current interdisciplinary clinical expertise into better defining the important phenomenon of pressure injury etiology and development.

Silane pre-treatments on copper and aluminium

International Nuclear Information System (INIS)

Deflorian, F.; Rossi, S.; Fedrizzi, L.

2006-01-01

environmentally friendly protective system, an epoxy-polyester powder coating was deposited on the silane treated metal surfaces. The influence of the pre-treatments on the adhesion of an organic coating was evaluated by adhesion tests in dry and wet conditions and the delamination of the coating, starting from a defect under specific environmental conditions, was measured. Some preliminary results appear very interesting and the deposition conditions were optimised, in particular the thermal curing (200 deg. C) of the silane layer is necessary to have a good coverage in the case of a copper substrate. The good adhesion also in wet conditions of the silane pre-treatments was also proven

Modeling of pretreatment and acidogenic fermentation of the organic fraction of municipal solid wastes

Energy Technology Data Exchange (ETDEWEB)

Beccari, M; Longo, G; Majone, M; Rolle, E; Scarinci, A [Rome ' ' La Sapienza' ' Univ. (Italy). Dept. of Chemistry

1993-01-01

The organic fraction of municipal solid waste represents a potential feedstock to be treated through biorefining. However, the process feasibility strongly depends on the effectiveness of a chemical pretreatment. Consequently, experimentation aimed at choosing the optimal type of reagent (alkali or acids) and optimal operating conditions was carried out. The best results were obtained using NaOH at room temperature. Solubilization data are in good agreement with a kinetics based on two competing reactions. Simulation of the overall process (pretreatment and acidogenic fermentation) taking place in two CFSTR reactors shows that an optimum ratio exists between the hydraulic residence times of the two stages of the process. (author)

Preoperative staging of rectal cancer.

Science.gov (United States)

Smith, Neil; Brown, Gina

2008-01-01

Detailed preoperative staging using high resolution magnetic resonance imaging (MRI) enables the selection of patients that require preoperative therapy for tumour regression. This information can be used to instigate neoadjuvant therapy in those patients with poor prognostic features prior to disturbing the tumour bed and potentially disseminating disease. The design of trials incorporating MR assessment of prognostic factors prior to therapy has been found to be of value in assessing treatment modalities and outcomes that are targeted to these preoperative prognostic subgroups and in providing a quantifiable assessment of the efficacy of particular chemoradiation treatment protocols by comparing pre-treatment MR staging with post therapy histology assessment. At present, we are focused on achieving clear surgical margins of excision (CRM) to avoid local recurrence. We recommend that all patients with rectal cancer should undergo pre-operative MRI staging. Of these, about half will have good prognosis features (T1-T3b, N0, EMVI negative, CRM clear) and may safely undergo primary total mesorectal excision. Of the remainder, those with threatened or involved margins will certainly benefit from pre-operative chemoradiotherapy with the aim of downstaging to permit safe surgical excision. In the future, our ability to recognise features predicting distant failure, such as extramural vascular invasion (EMVI) may be used to stratify patients for neo-adjuvant systemic chemotherapy in an effort to prevent distant relapse. The optimal pre-operative treatment regimes for these patients (radiotherapy alone, systemic chemotherapy alone or combination chemo-radiotherapy) is the subject of current and future trials.

Vaccines for preventing malaria (blood-stage).

Science.gov (United States)

Graves, P; Gelband, H

2006-10-18

A malaria vaccine is needed because of the heavy burden of mortality and morbidity due to this disease. This review describes the results of trials of blood (asexual)-stage vaccines. Several are under development, but only one (MSP/RESA, also known as Combination B) has been tested in randomized controlled trials. To assess the effect of blood-stage malaria vaccines in preventing infection, disease, and death. In March 2006, we searched the Cochrane Infectious Diseases Group Specialized Register, CENTRAL (The Cochrane Library 2006, Issue 1), MEDLINE, EMBASE, LILACS, and the Science Citation Index. We also searched conference proceedings and reference lists of articles, and contacted organizations and researchers in the field. Randomized controlled trials comparing blood-stage vaccines (other than SPf66) against P. falciparum, P. vivax, P. malariae, or P. ovale with placebo, control vaccine, or routine antimalarial control measures in people of any age receiving a challenge malaria infection. Both authors independently assessed trial quality and extracted data. Results for dichotomous data were expressed as relative risks (RR) with 95% confidence intervals (CI). Five trials of MSP/RESA vaccine with 217 participants were included; all five reported on safety, and two on efficacy. No severe or systemic adverse effects were reported at doses of 13 to 15 microg of each antigen (39 to 45 microg total). One small efficacy trial with 17 non-immune participants with blood-stage parasites showed no reduction or delay in parasite growth rates after artificial challenge. In the second efficacy trial in 120 children aged five to nine years in Papua New Guinea, episodes of clinical malaria were not reduced, but MSP/RESA significantly reduced parasite density only in children who had not been pretreated with an antimalarial drug (sulfadoxine-pyrimethamine). Infections with the 3D7 parasite subtype of MSP2 (the variant included in the vaccine) were reduced (RR 0.38, 95% CI 0.26 to

CT volumetry can potentially predict the local stage for gastric cancer after chemotherapy

Science.gov (United States)

Wang, Zhi-Cong; Wang, Chen; Ding, Ying; Ji, Yuan; Zeng, Meng-Su; Rao, Sheng-Xiang

2017-01-01

PURPOSE We aimed to evaluate the value of CT tumor volumetry for predicting T and N stages of gastric cancer after chemotherapy, with pathologic results as the reference standard. METHODS This study retrospectively evaluated 42 patients diagnosed with gastric cancer, who underwent chemotherapy followed by surgery. Pre- and post-treatment CT tumor volumes (VT) were measured in portal venous phase and volume reduction ratios were calculated. Correlations between pre- and post-treatment VT, reduction ratio, and pathologic stages were analyzed. Receiver operator characteristic (ROC) analyses were also performed to assess diagnostic performance for prediction of downstaging to T0–2 stage and N0 stage. RESULTS Pretreatment VT, post-treatment VT, and VT reduction ratio were significantly correlated with T stage (rs=0.329, rs=0.546, rs= −0.422, respectively). Post-treatment VT and VT reduction ratio were significantly correlated with N stage (rs=0.442 and rs= −0.376, respectively). Pretreatment VT, post-treatment VT, and VT reduction ratio were significantly different between T0–2 and T3,4 stage tumors (P = 0.05, P volumetry, particularly post-treatment measurement of VT, is potentially valuable for predicting histopathologic T and N stages after chemotherapy in patients with gastric cancer. PMID:28703101

The relationships between memory systems and sleep stages.

Science.gov (United States)

Rauchs, Géraldine; Desgranges, Béatrice; Foret, Jean; Eustache, Francis

2005-06-01

Sleep function remains elusive despite our rapidly increasing comprehension of the processes generating and maintaining the different sleep stages. Several lines of evidence support the hypothesis that sleep is involved in the off-line reprocessing of recently-acquired memories. In this review, we summarize the main results obtained in the field of sleep and memory consolidation in both animals and humans, and try to connect sleep stages with the different memory systems. To this end, we have collated data obtained using several methodological approaches, including electrophysiological recordings of neuronal ensembles, post-training modifications of sleep architecture, sleep deprivation and functional neuroimaging studies. Broadly speaking, all the various studies emphasize the fact that the four long-term memory systems (procedural memory, perceptual representation system, semantic and episodic memory, according to Tulving's SPI model; Tulving, 1995) benefit either from non-rapid eye movement (NREM) (not just SWS) or rapid eye movement (REM) sleep, or from both sleep stages. Tulving's classification of memory systems appears more pertinent than the declarative/non-declarative dichotomy when it comes to understanding the role of sleep in memory. Indeed, this model allows us to resolve several contradictions, notably the fact that episodic and semantic memory (the two memory systems encompassed in declarative memory) appear to rely on different sleep stages. Likewise, this model provides an explanation for why the acquisition of various types of skills (perceptual-motor, sensory-perceptual and cognitive skills) and priming effects, subserved by different brain structures but all designated by the generic term of implicit or non-declarative memory, may not benefit from the same sleep stages.

Stage III nasopharyngeal angiofibroma: Improving results with endoscopic-assisted midfacial degloving and modification to the Fisch staging system.

Science.gov (United States)

Shah, Saurin R; Keshri, Amit; Patadia, Simple; Sahu, Rabi Narayan; Srivastava, Arun Kumar; Behari, Sanjay

2015-10-01

To study outcomes with endoscopic-assisted midfacial degloving for Fisch stage III nasopharyngeal angiofibroma and propose a new staging system. Retrospective study of patients with Fisch stage III juvenile nasopharyngeal angiofibroma (JNA) including preoperative angiography, intraoperative blood loss and residue/recurrence following surgery. Tertiary care superspecialty referral center. Fifteen consecutive patients with Fisch stage III JNA undergoing operations over a period of 18 months. Preoperative angiography details, intraoperative blood loss, residue/recurrence, complications of surgery. Transarterial embolization with particulate agents followed by endoscopic-assisted midfacial degloving provides excellent outcomes with Fisch stage III JNAs. The modified Fisch staging system proposed would allow better preoperative evaluation and comparison of outcomes with different treatment options for stage III JNAs. Copyright © 2015 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Relationship to reducing sugar production and scanning electron microscope structure to pretreated hemp hurd biomass (Cannabis sativa)

International Nuclear Information System (INIS)

Abraham, Reinu E.; Barrow, Colin J.; Puri, Munish

2013-01-01

Lignocellulosic biomass is a highly rigid and recalcitrant structure which requires pretreatment to loosen chemical bonds to make accessible monomeric sugars for biofuel production. In this study, locally available biomass, that is hemp (Cannabis sativa), a low cost feedstock for ethanol production, has been used for the production of fermentable sugars. Hemp hurd biomass (HHB) was exposed to five different pretreatments which included dilute acid (H 2 SO 4 ), alkaline (NaOH), alkaline peroxide, hot water and one stage dilute acid (H 2 SO 4 ). Different pretreatments resulted in loosening and degradation of HHB structure thus facilitating enzymatic saccharification at optimized parameters (pH–4.8 and 50 °C). The changes in the reactive groups (hydroxyl or acetyl) of the HHB were confirmed by attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Scanning electron microscopy (SEM) was employed to characterize the surface morphology of untreated and treated HHB. Finally, enzymatic saccharification demonstrated maximum yield of total sugars (743 mg g −1 ) that are suitable for biofuel production. -- Highlights: • Hemp hurd biomass (HHB) was used for producing fermentable sugars. • Alkaline pretreatment resulted in loosening and degradation of hemp structure. • Pretreated HHB was characterized using FTIR studies. • SEM studies evaluated the opening of fiber bundles in pretreatment, thereby increasing cellulose access to enzymes. • Enzymatic saccharification of pretreated HHB demonstrated maximum yield of reducing sugars

Pretreatments employed in lignocellulosic materials for bioethanol production: an overview

OpenAIRE

Danay Carrillo-Nieves; Lourdes Zumalacárregui-de Cárdenas; Olga Sánchez-Collazo; Georgina Michelena-Alvarez; Hector Yznaga-Blanco; José Luis Martínez-Hernández; Cristóbal Noé-Aguilar

2014-01-01

Lignocellulosic materials are raw materials with high cellulose content and they constitute the most abun- dant sources of biomass on planet. They are attractive for their low cost and high availability in diverse climates and places for the bioethanol production, however, the main impediment for its use is the appro- priate selection from the technological and economic point of view of the stages of pretreatments and hydrolysis, that allow the breaking down of the lignocellulosic matrix to o...

Optimization of the pretreatment of Prosopis nigra sawdust for the production of fermentable sugars

Directory of Open Access Journals (Sweden)

Eliana P. Dagnino

2013-02-01

Full Text Available The black carob tree (Prosopis nigra is a particularly valued species in Chaco, Argentina on account of its hard wood. Finding a use for the sawdust, the main industrial residue of wood, could be useful within the furniture industry of any country in the tropics seeking to apply the biorefinery concept. For the conversion of wood carbohydrates to bioethanol, a pretreatment stage is necessary. The objective of this work was to find the acid pretreatment conditions that maximize the extraction of xylose with minimum degradation, while maximizing the concentration of glucans in the pretreated solid to obtain better enzymatic accessibility, using black carob tree sawdust as the raw material. The optimization was carried out by use of a central composite design (CCD with two independent variables: the concentration of the sulfuric acid solution and the heating time. Optimal enzymatic hydrolysis occurred at the mean values of the tested acid solution concentration (1.2% and after shorter heating times (10.2 min. The concentration of sugars after the enzymatic hydrolysis of the pretreated solid over a time period of 72 h was three times higher than the untreated solid.

Combined (alkaline+ultrasonic) pretreatment effect on sewage sludge disintegration.

Science.gov (United States)

Kim, Dong-Hoon; Jeong, Emma; Oh, Sae-Eun; Shin, Hang-Sik

2010-05-01

this enhanced performance was closely related to the solubilization increase of the sludge by pretreatment. However, enhanced anaerobic digestion resulted in 20% higher soluble N concentration in the reactor, which would be an additional burden in the subsequent nitrogen removal system.

Clinical significance of a proposed lymphoscintigrpahic functional grade system in patients with extremity lymphedema of stage i

International Nuclear Information System (INIS)

Choi, Joan Young; Hwang, Ji Hye; Kim, Dong Ik; Cho, Young Seok; Lee, Su Jin; Choi, Yong; Choe, Yeam Seong; Lee, Kyung Han; Kim, Byung Tae

2005-01-01

We proposed a new lymphoscintigrpahic functional grade (LGr) system in extremity lymphedema, and investigated the association between the LGr and a long-term response to physical therapy in patients with extremity lymphedema of stage I. The subjects were 20 patients with unilateral extremity lymphedema of stage I, who underwent pre-treatment extremity lymphoscintigraphy using Tc-99m antimony sulfur colloid, and were treated by complex decongestive physical therapy (CDPT). A proposed lymphoscintigrpahic functional grade system consisted of LGr 0 to LGr 4 according to the ilioinguinal nodal uptake, amount of dermal backflow, and uptake pattern of main and collateral lymphatics : LGr 0 = normal, LGr 1 = decreased lymphatic function without dermal backflow, LGr 2 = decreased lymphatic function with dermal backflow, LGr 3 = non - visualization of main lymphatics with dermal backflow, and LGr 4 = no significant lymphatic transport from injection site. LGr 2 was divided into 2A and 2B based on the amount of dermal backflow. A physician who is a lymphedema specialist determined the long-term outcome to CDPT with normalized response (NR), good response (GR) and poor response (PR) based on the change of edema volume reduction, skin status and occurrence of dermatolymphangioadenitis after the clinical follow-up for more than 1 year. Therapeutic responses were NR in 2 patients. GR in 9 patients and PR in 9 patients. Baseline LGrs were 1 in 7 patients, 2A in 4 patients, 2B in 5 patients, 3 in 2 patients, and 4 in 2 patients. There was a significant relationship between therapeutic response and LGr (p=0.003). In other words, 10 of 11 patients (91%) with LGr 1 or 2A showed NR. or GR. On the contrary, 8 of 9 patients (89%) with LGr 2B, 3 or 4 showed PR. Patients with unilateral extremity lymphedema of stage I had different lymphoscintigrpahic functional grades. This grade system may be useful to predict the response to physical therapy in such patients

Clinical significance of a proposed lymphoscintigrpahic functional grade system in patients with extremity lymphedema of stage i

Energy Technology Data Exchange (ETDEWEB)

Choi, Joan Young; Hwang, Ji Hye; Kim, Dong Ik; Cho, Young Seok; Lee, Su Jin; Choi, Yong; Choe, Yeam Seong; Lee, Kyung Han; Kim, Byung Tae [Samsung Medical Center, Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of)

2005-07-01

We proposed a new lymphoscintigrpahic functional grade (LGr) system in extremity lymphedema, and investigated the association between the LGr and a long-term response to physical therapy in patients with extremity lymphedema of stage I. The subjects were 20 patients with unilateral extremity lymphedema of stage I, who underwent pre-treatment extremity lymphoscintigraphy using Tc-99m antimony sulfur colloid, and were treated by complex decongestive physical therapy (CDPT). A proposed lymphoscintigrpahic functional grade system consisted of LGr 0 to LGr 4 according to the ilioinguinal nodal uptake, amount of dermal backflow, and uptake pattern of main and collateral lymphatics : LGr 0 = normal, LGr 1 = decreased lymphatic function without dermal backflow, LGr 2 = decreased lymphatic function with dermal backflow, LGr 3 = non - visualization of main lymphatics with dermal backflow, and LGr 4 = no significant lymphatic transport from injection site. LGr 2 was divided into 2A and 2B based on the amount of dermal backflow. A physician who is a lymphedema specialist determined the long-term outcome to CDPT with normalized response (NR), good response (GR) and poor response (PR) based on the change of edema volume reduction, skin status and occurrence of dermatolymphangioadenitis after the clinical follow-up for more than 1 year. Therapeutic responses were NR in 2 patients. GR in 9 patients and PR in 9 patients. Baseline LGrs were 1 in 7 patients, 2A in 4 patients, 2B in 5 patients, 3 in 2 patients, and 4 in 2 patients. There was a significant relationship between therapeutic response and LGr (p=0.003). In other words, 10 of 11 patients (91%) with LGr 1 or 2A showed NR. or GR. On the contrary, 8 of 9 patients (89%) with LGr 2B, 3 or 4 showed PR. Patients with unilateral extremity lymphedema of stage I had different lymphoscintigrpahic functional grades. This grade system may be useful to predict the response to physical therapy in such patients.

Comparison of manual and automated pretreatment methods for AMS radiocarbon dating of plant fossils

Science.gov (United States)

Bradley, L.A.; Stafford, Thomas W.

1994-01-01

A new automated pretreatment system for the preparation of materials submitted for accelerator mass spectrometry (AMS) analysis is less time-consuming and results in a higher sample yield. The new procedure was tested using two groups of plant fossils: one group was pretreated using the traditional method, and the second, using the automated pretreatment apparatus. The time it took to complete the procedure and the amount of sample material remaining were compared. The automated pretreatment apparatus proved to be more than three times faster and, in most cases, produced a higher yield. A darker discoloration of the KOH solutions was observed indicating that the automated system is more thorough in removing humates from the specimen compared to the manual method. -Authors

Low temperature lignocellulose pretreatment: effects and interactions of pretreatment pH are critical for maximizing enzymatic monosaccharide yields from wheat straw

DEFF Research Database (Denmark)

Pedersen, Mads; Johansen, Katja S.; Meyer, Anne S.

2011-01-01

Background: The recent development of improved enzymes and pentose-using yeast for cellulosic ethanol processes calls for new attention to the lignocellulose pretreatment step. This study assessed the influence of pretreatment pH, temperature, and time, and their interactions on the enzymatic...... alkaline pretreatments. Alkaline pretreatments also solubilized most of the lignin. Conclusions: Pretreatment pH exerted significant effects and factor interactions on the enzymatic glucose and xylose releases. Quite extreme pH values were necessary with mild thermal pretreatment strategies (T...... glucose and xylose yields from mildly pretreated wheat straw in multivariate experimental designs of acid and alkaline pretreatments. Results: The pretreatment pH was the most significant factor affecting both the enzymatic glucose and xylose yields after mild thermal pretreatments at maximum 140 degrees...

Department of Energy pretreatment of high-level and low-level wastes

International Nuclear Information System (INIS)

McGinnis, C.P.; Hunt, R.D.

1995-01-01

The remediation of the 1 x 10 8 gal of highly radioactive waste in the underground storage tanks (USTs) at five US Department of Energy (DOE) sites is one of DOE's greatest challenges. Therefore, the DOE Office of Environmental Management has created the Tank Focus Area (TFA) to manage an integrated technology development program that results in the safe and efficient remediation of UST waste. The TFA has divided its efforts into five areas, which are safety, characterization, retrieval/closure, pretreatment, and immobilization. All DOE pretreatment activities are integrated by the Pretreatment Technical Integration Manager of the TFA. For FY 1996, the 14 pretreatment tasks are divided into 3 systems: supernate separations, sludge treatment, and solid/liquid separation. The plans and recent results of these TFA tasks, which include two 25,000-gal demonstrations and two former TFA tasks on Cs removal, are presented. The pretreatment goals are to minimize the volume of high-level waste and the radioactivity in low-level waste

Determination of methyl methanesulfonate pretreatment effect in Drosophila melanogaster larvaes upon repair mechanisms in somatic cells

International Nuclear Information System (INIS)

Hernandez Paz, M.

1992-01-01

To make evident the existence of SOS repair mecanism in somatic cells, larvaes of drosophila melanogaster with MWH markers for females and FLR markers for males were used. This larvaes received a pretreatment with MMS at concentrations of 0.0007% and 0.0014% during 24 hours and latter a treatment with gamma rays at different dosis. SMART program was used to make stastistical evaluations. Small spots were observed which can have two origins. First could be damage in the last part of third stage in which cells are in last divisions and second could be the damage to larvaes in early stages in shich pretreatment with MMS cause lesions which prevent the reproduction of the cells. Also big spots were observed which presence is due to recombination. It was detected than the bigger the concentration of MMS and radiation dose, the bigger the induced damage. In some groups such observation was impossible may be to technical problems as relative humidity, out of phase in the growth of larvaes giving place that treatment were given in three stages. For this reasons it was impossible to discriminate if drosophila melanogaster is wheter or not capable to induce a repair mechanism (Author)

Influence of alkaline hydrothermal pretreatment on shrub wood Tamarix ramosissima: Characteristics of degraded lignin

International Nuclear Information System (INIS)

Xiao, Ling-Ping; Bai, Yuan-Yuan; Shi, Zheng-Jun; Lu, Qiang; Sun, Run-Cang

2014-01-01

The objective of this work was to evaluate the influence of alkaline hydrothermal (AH) pretreatment on the physicochemical properties of the degraded lignins, attempt to upgrade the potential of lignin for value-added chemicals and fuel production. For this purpose, shrub wood Tamarix ramosissima lignin was fractionated using a two-stage process based on an AH pretreatment followed by an alkaline ethanol post-treatment. The recovered lignin fractions were investigated by comparison with milled wood lignin (MWL) in terms of fractionation yield, carbohydrate composition, gel permeation chromatography, Fourier transform infrared spectroscopy, 13 C and 2D heteronuclear single quantum correlation nuclear magnetic resonance, as well as pyrolysis-gas chromatography/mass spectrometry. The result showed that AH pretreatment led to the degradation of β-O-4 linkages and consequently the increased severity caused a release of more S-units lignin fractions with molecular weights between 1300 and 2500 g/mol in the liquid but higher molecular weights (3000–4400 g/mol) in the residues. Moreover, it was found that the lignin syringyl-to-guaiacyl (S/G) ratios from analytical pyrolysis slightly changed after AH pretreatment (S/G, 1.8–2.3) but higher than those of MWL (S/G, 1.7). Overall, the present study demonstrates that these lignins dissolved during AH pretreatment and those recovered from the solid residues isolated with alkaline ethanol post-treatment could be profitably exploited as feedstock in integrated forest biorefineries, rather than traditional use as low-value energy sources.- Highlights: • Alkaline hydrothermal pretreatment and alkaline ethanol post-treatment were proposed. • The influence of AH pretreatment on the lignin structural changes was characterized. • Aryl-O-ether linkages of lignin were extensively cleaved. • Lignin recovered from solid residue is a potential resource for the production of value-added chemicals

Relationship to reducing sugar production and scanning electron microscope structure to pretreated hemp hurd biomass (Cannabis sativa)

Energy Technology Data Exchange (ETDEWEB)

Abraham, Reinu E.; Barrow, Colin J.; Puri, Munish

2013-11-15

Lignocellulosic biomass is a highly rigid and recalcitrant structure which requires pretreatment to loosen chemical bonds to make accessible monomeric sugars for biofuel production. In this study, locally available biomass, that is hemp (Cannabis sativa), a low cost feedstock for ethanol production, has been used for the production of fermentable sugars. Hemp hurd biomass (HHB) was exposed to five different pretreatments which included dilute acid (H{sub 2}SO{sub 4}), alkaline (NaOH), alkaline peroxide, hot water and one stage dilute acid (H{sub 2}SO{sub 4}). Different pretreatments resulted in loosening and degradation of HHB structure thus facilitating enzymatic saccharification at optimized parameters (pH–4.8 and 50 °C). The changes in the reactive groups (hydroxyl or acetyl) of the HHB were confirmed by attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Scanning electron microscopy (SEM) was employed to characterize the surface morphology of untreated and treated HHB. Finally, enzymatic saccharification demonstrated maximum yield of total sugars (743 mg g{sup −1}) that are suitable for biofuel production. -- Highlights: • Hemp hurd biomass (HHB) was used for producing fermentable sugars. • Alkaline pretreatment resulted in loosening and degradation of hemp structure. • Pretreated HHB was characterized using FTIR studies. • SEM studies evaluated the opening of fiber bundles in pretreatment, thereby increasing cellulose access to enzymes. • Enzymatic saccharification of pretreated HHB demonstrated maximum yield of reducing sugars.

Utility of the CPS+EG staging system in hormone receptor-positive, human epidermal growth factor receptor 2-negative breast cancer treated with neoadjuvant chemotherapy.

Science.gov (United States)

Marmé, Frederik; Lederer, Bianca; Blohmer, Jens-Uwe; Costa, Serban Dan; Denkert, Carsten; Eidtmann, Holger; Gerber, Bernd; Hanusch, Claus; Hilfrich, Jörn; Huober, Jens; Jackisch, Christian; Kümmel, Sherko; Loibl, Sibylle; Paepke, Stefan; Untch, Michael; von Minckwitz, Gunter; Schneeweiss, Andreas

2016-01-01

Pathologic complete response after neoadjuvant chemotherapy (NACT) correlates with overall survival (OS) in primary breast cancer. A recently described staging system based on pre-treatment clinical stage (CS), final pathological stage (PS), estrogen receptor (ER) status and nuclear grade (NG) leads to a refined estimation of prognosis in unselected patients. Its performance in luminal type breast cancers has not been determined. This study investigates the clinical utility of this CPS+EG score when restricted to hormone receptor-positive (HR+)/human epidermal growth factor receptor 2-negative (HER2-) patients and compares the results to a cohort of unselected patients. The CPS+EG score was calculated for 6637 unselected patients and 2454 patients with HR+/HER2- tumours who received anthracycline/taxane-based NACT within 8 prospective German trials. Five-year disease-free survival (DFS) and OS were 75.6% and 84.1% for the unselected cohort and 80.6% and 87.8% for the HR+/HER2- subgroup, respectively. The CPS+EG system distinguished different prognostic groups with 5-year DFS ranging from 0% to 91%. The CPS+EG system leads to an improved categorisation of patients by outcome compared to CS, PS, ER or NG alone. When applying the CPS+EG score to the HR+/HER2- subgroup, a shift to lower scores was observed compared to the overall population, but 5-year DFS and OS for the individual scores were identical to that observed in the overall population. In HR+/HER2- patients, the CPS+EG staging system retains its ability to facilitate a refined stratification of patients according to outcome. It can help to select candidates for post-neoadjuvant clinical trials in luminal breast cancer. Copyright © 2015 Elsevier Ltd. All rights reserved.

Comparison of five systems for staging lymph node metastasis in gastric cancer.

Science.gov (United States)

Yu, W; Choi, G S; Whang, I; Suh, I S

1997-09-01

There are several systems for staging lymph node metastasis in gastric cancer. Their relative merits are not clear. In this retrospective analysis, the nodal status was classified according to the Union Internacional Contra la Cancrum (UICC) and Japanese staging systems, the number and frequency of lymph node metastasis, and the level of involved nodes. Each staging system was scored as good (+1), fair (0) or poor (-1) with respect to prognostic value, theoretical value, convenience, reproducibility and surgical applicability. There were no differences between the five staging systems in predicting survival. The Japanese staging system was most arbitrary owing to the complexity of the system, although it had an advantage in surgical application. The same disadvantage was found in the UICC system and the level system. Determination of the number and frequency of involved nodes was convenient and reproducible, but the number of lymph nodes dissected must be considered when the number of positive nodes is used for staging. The classification of metastasis to the regional lymph nodes as N0 (no nodal metastasis), N1 (metastasis in 1-25 per cent of dissected nodes) and N2 (metastasis in more than 25 per cent of dissected nodes) would be a simple, convenient, reproducible staging system with an ability to predict surgical results.

GREET Pretreatment Module

Energy Technology Data Exchange (ETDEWEB)

Adom, Felix K. [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; Dunn, Jennifer B. [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; Han, Jeongwoo [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division

2014-09-01

A wide range of biofuels and biochemicals can be produced from cellulosic biomass via different pretreatment technologies that yield sugars. Process simulations of dilute acid and ammonia fiber expansion pretreatment processes and subsequent hydrolysis were developed in Aspen Plus for four lignocellulosic feedstocks (corn stover, miscanthus, switchgrass, and poplar). This processing yields sugars that can be subsequently converted to biofuels or biochemical. Material and energy consumption data from Aspen Plus were then compiled in a new Greenhouses Gases, Regulated Emissions, and Energy Use in Transportation (GREET^TM) pretreatment module. The module estimates the cradle-to-gate fossil energy consumption (FEC) and greenhouse gas (GHG) emissions associated with producing fermentable sugars. This report documents the data and methodology used to develop this module and the cradle-to-gate FEC and GHG emissions that result from producing fermentable sugars.

Optical monitoring systems for thermal spray processes: droplets behavior and substrate pre-treatments

Science.gov (United States)

Kawaguchi, Y.; Kobayashi, N.; Yamagata, Y.; Miyazaki, F.; Yamasaki, M.; Tanaka, J.; Muraoka, K.

2017-11-01

Thermal spray is a technique to form molten droplets using either plasma- or combustion-heating, which impinge upon substrates to form coating layers for various purposes, such as anti-corrosion and anti-wear layers. Although it is an established technique having a history of more than a century, operations of spray guns together with preparing suitable substrate surfaces for obtaining good coating layers still rely on experienced technicians. Because of the necessity of meeting more and more stringent requirements for coating quality and cost from customers, there has been a strong need to try to monitor spray processes, so as to obtain the best possible spray coating layers. The basic requirements for such monitoring systems are *reasonably cheap, *easy operation for laypersons, *easy access to targets to be investigated, and *an in-situ capability. The purpose of the present work is to provide suitable optical monitoring systems for (1) droplets behavior and (2) substrate pre-treatments. For the former (1), the first result was already presented at the 17th laser-aided plasma diagnostics meeting (LAPD17) in 2015 in Sapporo, and the results of its subsequent applications into real spray environments are shown in this article in order to validate the previous proposal. Topic (2) is new in the research program, and the proof-of-principle experiment for the proposed method yielded a favorable result. Based on this positive result, an overall strategy is being planned to fulfill the final objective of the optical monitoring of substrate pre-treatments. Details of these two programs (1) and (2) together with the present status are described.

Processes for pretreating lignocellulosic biomass: A review

Energy Technology Data Exchange (ETDEWEB)

McMillan, J.D.

1992-11-01

This paper reviews existing and proposed pretreatment processes for biomass. The focus is on the mechanisms by which the various pretreatments act and the influence of biomass structure and composition on the efficacy of particular pretreatment techniques. This analysis is used to identify pretreatment technologies and issues that warrant further research.

Utilization of microwave and ultrasound pretreatments in the production of bioethanol from corn

Energy Technology Data Exchange (ETDEWEB)

Nikolic, Svetlana; Mojovic, Ljiljana; Rakin, Marica [University of Belgrade, Faculty of Technology and Metallurgy, Belgrade (Serbia); Pejin, Dusanka; Pejin, Jelena [University of Novi Sad, Faculty of Technology, Novi Sad (Serbia)

2011-08-15

Bioethanol production by simultaneous saccharification and fermentation (SSF) of corn meal by Saccharomyces cerevisiae var. ellipsoideus yeast in a batch system with prior ultrasound or microwave treatment was studied. The optimal duration of the pretreatments and the SSF process kinetics were assessed and determined. Also, the effect of ultrasound and microwave pretreatments on ethanol yield and productivity was investigated. An optimal duration of 5 min was determined for both pretreatments. Ultrasonic and microwave pretreatments effectively increased the glucose concentration obtained after liquefaction by 6.82 and 8.48%, respectively, compared to untreated control sample. Also, both pretreatments improved ethanol yield and productivity during the SSF process. Ultrasound and microwave pretreatments increased the maximum ethanol concentration produced in the SSF process by 11.15 and 13.40% (compared to the control sample), respectively. The application of microwave pretreatment resulted in higher glucose release during liquefaction and consequently in higher ethanol concentration, compared to ultrasound pretreatment. A maximum ethanol concentration of 9.91% (w/w) and percentage of theoretical ethanol yield of 92.27% were achieved after 44 h of the SSF process of corn meal with prior microwave treatment. (orig.)

The pretreatment of corn stover with Gloeophyllum trabeum KU-41 for enzymatic hydrolysis

Directory of Open Access Journals (Sweden)

Gao Ziqing

2012-05-01

Full Text Available Abstract Background Pretreatment is an essential step in the enzymatic hydrolysis of biomass for bio-ethanol production. The dominant concern in this step is how to decrease the high cost of pretreatment while achieving a high sugar yield. Fungal pretreatment of biomass was previously reported to be effective, with the advantage of having a low energy requirement and requiring no application of additional chemicals. In this work, Gloeophyllum trabeum KU-41 was chosen for corn stover pretreatment through screening with 40 strains of wood-rot fungi. The objective of the current work is to find out which characteristics of corn stover pretreated with G. trabeum KU-41 determine the pretreatment method to be successful and worthwhile to apply. This will be done by determining the lignin content, structural carbohydrate, cellulose crystallinity, initial adsorption capacity of cellulase and specific surface area of pretreated corn stover. Results The content of xylan in pretreated corn stover was decreased by 43% in comparison to the untreated corn stover. The initial cellulase adsorption capacity and the specific surface area of corn stover pretreated with G. trabeum were increased by 7.0- and 2.5-fold, respectively. Also there was little increase in the cellulose crystallinity of pretreated corn stover. Conclusion G. trabeum has an efficient degradation system, and the results indicated that the conversion of cellulose to glucose increases as the accessibility of cellulose increases due to the partial removal of xylan and the structure breakage of the cell wall. This pretreatment method can be further explored as an alternative to the thermochemical pretreatment method.

The effectiveness of pretreatment physics plan review for detecting errors in radiation therapy

International Nuclear Information System (INIS)

Gopan, Olga; Zeng, Jing; Novak, Avrey; Nyflot, Matthew; Ford, Eric

2016-01-01

Purpose: The pretreatment physics plan review is a standard tool for ensuring treatment quality. Studies have shown that the majority of errors in radiation oncology originate in treatment planning, which underscores the importance of the pretreatment physics plan review. This quality assurance measure is fundamentally important and central to the safety of patients and the quality of care that they receive. However, little is known about its effectiveness. The purpose of this study was to analyze reported incidents to quantify the effectiveness of the pretreatment physics plan review with the goal of improving it. Methods: This study analyzed 522 potentially severe or critical near-miss events within an institutional incident learning system collected over a three-year period. Of these 522 events, 356 originated at a workflow point that was prior to the pretreatment physics plan review. The remaining 166 events originated after the pretreatment physics plan review and were not considered in the study. The applicable 356 events were classified into one of the three categories: (1) events detected by the pretreatment physics plan review, (2) events not detected but “potentially detectable” by the physics review, and (3) events “not detectable” by the physics review. Potentially detectable events were further classified by which specific checks performed during the pretreatment physics plan review detected or could have detected the event. For these events, the associated specific check was also evaluated as to the possibility of automating that check given current data structures. For comparison, a similar analysis was carried out on 81 events from the international SAFRON radiation oncology incident learning system. Results: Of the 356 applicable events from the institutional database, 180/356 (51%) were detected or could have been detected by the pretreatment physics plan review. Of these events, 125 actually passed through the physics review; however

The effectiveness of pretreatment physics plan review for detecting errors in radiation therapy

Energy Technology Data Exchange (ETDEWEB)

Gopan, Olga; Zeng, Jing; Novak, Avrey; Nyflot, Matthew; Ford, Eric, E-mail: eford@uw.edu [Department of Radiation Oncology, University of Washington Medical Center, 1959 NE Pacific Street, Box 356043, Seattle, Washington 98195 (United States)

2016-09-15

Purpose: The pretreatment physics plan review is a standard tool for ensuring treatment quality. Studies have shown that the majority of errors in radiation oncology originate in treatment planning, which underscores the importance of the pretreatment physics plan review. This quality assurance measure is fundamentally important and central to the safety of patients and the quality of care that they receive. However, little is known about its effectiveness. The purpose of this study was to analyze reported incidents to quantify the effectiveness of the pretreatment physics plan review with the goal of improving it. Methods: This study analyzed 522 potentially severe or critical near-miss events within an institutional incident learning system collected over a three-year period. Of these 522 events, 356 originated at a workflow point that was prior to the pretreatment physics plan review. The remaining 166 events originated after the pretreatment physics plan review and were not considered in the study. The applicable 356 events were classified into one of the three categories: (1) events detected by the pretreatment physics plan review, (2) events not detected but “potentially detectable” by the physics review, and (3) events “not detectable” by the physics review. Potentially detectable events were further classified by which specific checks performed during the pretreatment physics plan review detected or could have detected the event. For these events, the associated specific check was also evaluated as to the possibility of automating that check given current data structures. For comparison, a similar analysis was carried out on 81 events from the international SAFRON radiation oncology incident learning system. Results: Of the 356 applicable events from the institutional database, 180/356 (51%) were detected or could have been detected by the pretreatment physics plan review. Of these events, 125 actually passed through the physics review; however

The stages of the international drug control system.

Science.gov (United States)

Carstairs, Catherine

2005-01-01

This paper argues that the history of the international drug control system of the League of Nations/United Nations can be divided into three cumulative stages. The first stage, the supply stage, dates back to early part of the 20th century, and aimed to reduce the supply of drugs through careful monitoring and trade regulations. This has remained the dominant control strategy. In the middle of the century, demand control, in the form of treatment and criminalization of the individual user, began to appear. This was the least successful stage. Finally, in the 1980s, the dangers of the drug traffic assumed an important place on the international agenda and measures to reduce drug-related organized crime were enacted. To date, this has been a process of proliferation of regulatory strategies. Recently, new challenges to the international drug control system have emerged, including well-funded non-governmental organizations critical of the war on drugs, and the adoption of harm reduction measures in national policies around the world.

Intestinal diffuse large B-cell lymphoma: an evaluation of different staging systems.

Science.gov (United States)

Hwang, Hee Sang; Yoon, Dok Hyun; Suh, Cheolwon; Park, Chan-Sik; Huh, Jooryung

2014-01-01

The gastrointestinal tract is the most common primary extranodal site for diffuse large B-cell lymphoma (DLBCL). However, there is no consensus on the most appropriate staging system for intestinal DLBCL. We evaluated the utility of the modified Ann Arbor system, the Lugano system, and the Paris staging system (a modification of the Tumor, Node, Metastases [TNM] staging for epithelial tumors) in 66 cases of resected intestinal DLBCL. The cases were treated with surgery, plus either cyclophosphamide, doxorubicin, vincristine, and prednisolone (CHOP) chemotherapy alone (n=26) or with the addition of rituximab immunotherapy (n=40). Median follow-up time was 40.4 months (range, 2.1-171.6 months). Fifty-six patients (84.8%) achieved complete remission. The overall 5-yr survival rate was 86.4% (57/66). Of the stage categories defined for each staging system, only the T stage of the Paris classification showed prognostic significance for overall survival by univariate analysis. However, none of the stage parameters was significantly correlated with patient survival on multivariate analysis. In conclusion, the results suggest that the T stage of the Paris classification system may be a prognostic indicator in intestinal DLBCL. The results also imply that in surgically resected intestinal DLBCL, the addition of rituximab to the CHOP regimen does not confer significant survival advantage.

Impact of Pretreatment Tumor Growth Rate on Outcome of Early-Stage Lung Cancer Treated With Stereotactic Body Radiation Therapy

Energy Technology Data Exchange (ETDEWEB)

Atallah, Soha; Cho, B.C. John; Allibhai, Zishan; Taremi, Mojgan; Giuliani, Meredith [Radiation Medicine Program, Princess Margaret Cancer Centre, Toronto, Ontario (Canada); Department of Radiation Oncology, University of Toronto, Toronto, Ontario (Canada); Le, Lisa W. [Department of Biostatistics, Princess Margaret Cancer Centre, Toronto, Ontario (Canada); Brade, Anthony; Sun, Alexander; Bezjak, Andrea [Radiation Medicine Program, Princess Margaret Cancer Centre, Toronto, Ontario (Canada); Department of Radiation Oncology, University of Toronto, Toronto, Ontario (Canada); Hope, Andrew J., E-mail: andrew.hope@rmp.uhn.on.ca [Radiation Medicine Program, Princess Margaret Cancer Centre, Toronto, Ontario (Canada); Department of Radiation Oncology, University of Toronto, Toronto, Ontario (Canada)

2014-07-01

Purpose: To determine the influence of pretreatment tumor growth rate on outcomes in patients with early-stage non-small cell lung cancer (NSCLC) treated with stereotactic body radiation therapy (SBRT). Methods and Materials: A review was conducted on 160 patients with T1-T2N0M0 NSCLC treated with SBRT at single institution. The patient's demographic and clinical data, time interval (t) between diagnostic and planning computed tomography (CT), vital status, disease status, and cause of death were extracted from a prospectively kept database. Differences in gross tumor volume between diagnostic CT (GTV1) and planning CT (GTV2) were recorded, and growth rate was calculated by use of specific growth rate (SGR). Kaplan-Meier curves were constructed for overall survival (OS). Differences between groups were compared with a log-rank test. Multivariate analyses were performed by use of the Cox proportional hazard model with SGR and other relevant clinical factors. Cumulative incidence was calculated for local, regional, and distant failures by use of the competing risk approach and was compared with Gray's test. Results: The median time interval between diagnostic and planning CT was 82 days. The patients were divided into 2 groups, and the median SGR was used as a cut-off. The median survival times were 38.6 and 27.7 months for the low and high SGR groups, respectively (P=.03). Eastern Cooperative Oncology Group performance status (P=.01), sex (P=.04), SGR (P=.03), and GTV2 (P=.002) were predictive for OS in multivariable Cox regression analysis and, except sex, were similarly predictive for failure-free survival (FFS). The 3-year cumulative incidences of regional failure were 19.2% and 6.0% for the high and low SGR groups, respectively (P=.047). Conclusion: High SGR was correlated with both poorer OS and FFS in patients with early-stage NSCLC treated with SBRT. If validated, this measurement may be useful in identifying patients most likely to benefit from

Review of pretreatment processes for lignocellulosic ethanol production, and development of an innovative method

International Nuclear Information System (INIS)

Chiaramonti, David; Prussi, Matteo; Ferrero, Simone; Oriani, Luis; Ottonello, Piero; Torre, Paolo; Cherchi, Francesco

2012-01-01

Biomass pretreatment aims at separating and providing easier access to the main biomass components (cellulose, hemicellulose and lignin), eventually removing lignin, preserving the hemicellulose, reducing the cellulose crystallinity and increasing the porosity of the material. Pretreatment is an essential step towards the development and industrialization of efficient 2nd generation lignocellulosic ethanol processes. The present work reviewed the main options available in pretreatment. Autohydrolysis and steam explosion were then selected for further investigation. Experimental work was carried out on batch scale reactors, using Miscanthus as biomass feedstock: the effects on sugar solubilization and degradation products generation have been examined for each of these two pretreatment systems. A new process using only water and steam as reacting media was then developed, experimentally tested, and results compared to those achieved by the autohydrolysis and steam explosion processes. Products obtained with the new pretreatment contained a lower amount of usual fermentation inhibitor compounds compared to that typically obtained in steam explosion. This result was achieved under operating conditions that at the same time allowed a good xylan yield, preventing degradation of hemicelluloses. The new pretreatment process was also able to act as an equalization step, as the solid material from the pretreatment phase had a similar composition even under different operating conditions. As regards the effect of pretreatment on enzymatic hydrolysis, the new process achieved yields similar to steam explosion on glucans: however, this was obtained reducing the formation of degradation products from sugars, mainly from C5 sugars. These results made the proposed pretreatment system suitable for further development and industrialization on pilot and industrial scale.

Prognostic value of pretreatment albumin/globulin ratio in digestive system cancers: A meta-analysis.

Science.gov (United States)

Guo, Hui-Wen; Yuan, Tang-Zhan; Chen, Jia-Xi; Zheng, Yang

2018-01-01

The albumin/globulin ratio (AGR) has been widely reported to be a potential predictor of prognosis in digestive system cancers (DSCs), but convincing conclusions have not been made. Therefore, herein, we performed a meta-analysis of relevant studies regarding this topic to evaluate the prognostic value of AGR in patients with DSCs. Three databases, including PubMed, EMBase, and Web of science, were searched comprehensively for eligible studies through September 8, 2017. The outcomes of interest included overall survival (OS), disease-free survival (DFS), and cancer-specific survival (CSS). In our meta-analysis, pooled analysis of 13 studies with 9269 patients showed that a low AGR was significantly correlated with poor OS (HR = 1.94; 95% CI: 1.57-2.38; P digestive system cancers. A low pretreatment AGR may be a useful predictive prognostic biomarker in human digestive system cancers.

Improved sugar yields from biomass sorghum feedstocks: comparing low-lignin mutants and pretreatment chemistries.

Science.gov (United States)

Godin, Bruno; Nagle, Nick; Sattler, Scott; Agneessens, Richard; Delcarte, Jérôme; Wolfrum, Edward

2016-01-01

For biofuel production processes to be economically efficient, it is essential to maximize the production of monomeric carbohydrates from the structural carbohydrates of feedstocks. One strategy for maximizing carbohydrate production is to identify less recalcitrant feedstock cultivars by performing some type of experimental screening on a large and diverse set of candidate materials, or by identifying genetic modifications (random or directed mutations or transgenic plants) that provide decreased recalcitrance. Economic efficiency can also be increased using additional pretreatment processes such as deacetylation, which uses dilute NaOH to remove the acetyl groups of hemicellulose prior to dilute acid pretreatment. In this work, we used a laboratory-scale screening tool that mimics relevant thermochemical pretreatment conditions to compare the total sugar yield of three near-isogenic brown midrib ( bmr ) mutant lines and the wild-type (WT) sorghum cultivar. We then compared results obtained from the laboratory-scale screening pretreatment assay to a large-scale pretreatment system. After pretreatment and enzymatic hydrolysis, the bmr mutants had higher total sugar yields than the WT sorghum cultivar. Increased pretreatment temperatures increased reactivity for all sorghum samples reducing the differences observed at lower reaction temperatures. Deacetylation prior to dilute acid pretreatment increased the total sugar yield for all four sorghum samples, and reduced the differences in total sugar yields among them, but solubilized a sizable fraction of the non-structural carbohydrates. The general trends of increased total sugar yield in the bmr mutant compared to the WT seen at the laboratory scale were observed at the large-scale system. However, in the larger reactor system, the measured total sugar yields were lower and the difference in total sugar yield between the WT and bmr sorghum was larger. Sorghum bmr mutants, which have a reduced lignin content showed

40 CFR 35.907 - Municipal pretreatment program.

Science.gov (United States)

2010-07-01

... industrial survey as required by § 403.8 of this chapter including identification of system users, the... program; (4) A determination of technical information necessary to support development of an industrial waste ordinance or other means of enforcing pretreatment standards; (5) Design of a monitoring...

End-Stage Renal Disease Prospective Payment System

Data.gov (United States)

U.S. Department of Health & Human Services — This final rule implements a case-mix adjusted bundled prospective payment system (PPS) for Medicare outpatient end-stage renal disease (ESRD) dialysis facilities...

Process performance assessment of advanced anaerobic digestion of sewage sludge including sequential ultrasound-thermal (55 °C) pre-treatment.

Science.gov (United States)

Neumann, Patricio; Barriga, Felipe; Álvarez, Claudia; González, Zenón; Vidal, Gladys

2018-03-15

The aim of this study was to evaluate the performance and digestate quality of advanced anaerobic digestion of sewage sludge including sequential ultrasound-thermal (55 °C) pre-treatment. Both stages of pre-treatment contributed to chemical oxygen demand (COD) solubilization, with an overall factor of 11.4 ± 2.2%. Pre-treatment led to 19.1, 24.0 and 29.9% increased methane yields at 30, 15 and 7.5 days solid retention times (SRT), respectively, without affecting process stability or accumulation of intermediates. Pre-treatment decreased up to 4.2% water recovery from the digestate, but SRT was a more relevant factor controlling dewatering. Advanced digestion showed 2.4-3.1 and 1.5 logarithmic removals of coliforms and coliphages, respectively, and up to a 58% increase in the concentration of inorganics in the digestate solids compared to conventional digestion. The COD balance of the process showed that the observed increase in methane production was proportional to the pre-treatment solubilization efficiency. Copyright © 2018 Elsevier Ltd. All rights reserved.

Analysis of multi-stage open shop processing systems

NARCIS (Netherlands)

Eggermont, C.E.J.; Schrijver, A.; Woeginger, G.J.; Schwentick, T.; Dürr, C.

2011-01-01

We study algorithmic problems in multi-stage open shop processing systems that are centered around reachability and deadlock detection questions. We characterize safe and unsafe system states. We show that it is easy to recognize system states that can be reached from the initial state (where the

Production of l(+)-lactic acid from acid pretreated sugarcane bagasse using Bacillus coagulans DSM2314 in a simultaneous saccharification and fermentation strategy.

Science.gov (United States)

van der Pol, Edwin C; Eggink, Gerrit; Weusthuis, Ruud A

2016-01-01

Sugars derived from lignocellulose-rich sugarcane bagasse can be used as feedstock for production of l(+)-lactic acid, a precursor for renewable bioplastics. In our research, acid-pretreated bagasse was hydrolysed with the enzyme cocktail GC220 and fermented by the moderate thermophilic bacterium Bacillus coagulans DSM2314. Saccharification and fermentation were performed simultaneously (SSF), adding acid-pretreated bagasse either in one batch or in two stages. SSF was performed at low enzyme dosages of 10.5-15.8 FPU/g DW bagasse. The first batch SSF resulted in an average productivity of 0.78 g/l/h, which is not sufficient to compete with lactic acid production processes using high-grade sugars. Addition of 1 g/l furfural to precultures can increase B. coagulans resistance towards by-products present in pretreated lignocellulose. Using furfural-containing precultures, productivity increased to 0.92 g/l/h, with a total lactic acid production of 91.7 g in a 1-l reactor containing 20% W/W DW bagasse. To increase sugar concentrations, bagasse was solubilized with a liquid fraction, obtained directly after acid pretreatment. Solubilizing the bagasse fibres with water increased the average productivity to 1.14 g/l/h, with a total lactic acid production of 84.2 g in a 1-l reactor. Addition of bagasse in two stages reduced viscosity during SSF, resulting in an average productivity in the first 23 h of 2.54 g/l/h, similar to productivities obtained in fermentations using high-grade sugars. Due to fast accumulation of lactic acid, enzyme activity was repressed during two-stage SSF, resulting in a decrease in productivity and a slightly lower total lactic acid production of 75.6 g. In this study, it is shown that an adequate production of lactic acid from lignocellulose was successfully accomplished by a two-stage SSF process, which combines acid-pretreated bagasse, B. coagulans precultivated in the presence of furfural as microorganism, and GC220 as enzyme

The global stability of a delayed predator-prey system with two stage-structure

International Nuclear Information System (INIS)

Wang Fengyan; Pang Guoping

2009-01-01

Based on the classical delayed stage-structured model and Lotka-Volterra predator-prey model, we introduce and study a delayed predator-prey system, where prey and predator have two stages, an immature stage and a mature stage. The time delays are the time lengths between the immature's birth and maturity of prey and predator species. Results on global asymptotic stability of nonnegative equilibria of the delay system are given, which generalize and suggest that good continuity exists between the predator-prey system and its corresponding stage-structured system.

Pretreatment techniques for biofuels and biorefineries

Energy Technology Data Exchange (ETDEWEB)

Fang, Zhen (ed.) [Chinese Academy of Sciences, Kunming, YN (China). Xishuangbanna Tropical Botonical Garden

2013-02-01

The first book focused on pretreatment techniques for biofuels contributed by the world's leading experts. Extensively covers the different types of biomass, various pretreatment approaches and methods that show the subsequent production of biofuels and chemicals. In addition to traditional pretreatment methods, novel techniques are also introduced and discussed. An accessible reference work for students, researchers, academicians and industrialists in biorefineries. This book includes 19 chapters contributed by the world's leading experts on pretreatment methods for biomass. It extensively covers the different types of biomass (e.g. molasses, sugar beet pulp, cheese whey, sugarcane residues, palm waste, vegetable oil, straws, stalks and wood), various pretreatment approaches (e.g. physical, thermal, chemical, physicochemical and biological) and methods that show the subsequent production of biofuels and chemicals such as sugars, ethanol, extracellular polysaccharides, biodiesel, gas and oil. In addition to traditional methods such as steam, hot-water, hydrothermal, diluted-acid, organosolv, ozonolysis, sulfite, milling, fungal and bacterial, microwave, ultrasonic, plasma, torrefaction, pelletization, gasification (including biogas) and liquefaction pretreatments, it also introduces and discusses novel techniques such as nano and solid catalysts, organic electrolyte solutions and ionic liquids. This book offers a review of state-of-the-art research and provides guidance for the future paths of developing pretreatment techniques of biomass for biofuels, especially in the fields of biotechnology, microbiology, chemistry, materials science and engineering. It intends to provide a systematic introduction of pretreatment techniques. It is an accessible reference work for students, researchers, academicians and industrialists in biorefineries.

[Comparison of differentiated thyroid carcinoma staging systems in a Spanish population].

Science.gov (United States)

Andía Melero, Víctor Manuel; Martín de Santa-Olalla Llanes, María; Sambo Salas, Marcel; Percovich Hualpa, Juan Carlos; Motilla de la Cámara, Marta; Collado Yurrita, Luis

2015-04-01

Differentiated thyroid carcinoma staging is increasingly important due to the current trends to a less intensive therapy in low-risk patients. The TNM system is most widely used, but other systems based on follow-up of several patient cohorts have been developed. When these systems have been applied to other populations, results have been discordant. Our study evaluates the suitability of several differentiated thyroid carcinoma staging systems in a Spanish population. 729 patients with differentiated thyroid carcinoma and staging data available were enrolled. Mean follow-up time was 10.8 years. The TNM, EORTC, AMES, Clinical class, MACIS, Ohio, NTCTCS, and Spanish systems were applied to all histological types. The Kaplan-Meier survival curves for each system were analyzed, and compared using the proportion of explained variation (PEV). The demographic and clinical characteristics of our population were similar to those of other Spanish and international cohorts reported. The best systems were NTCTCS, with 74.7% PEV, and TNM (68.3%), followed by the Ohio, MACIS, EORTC, and AMES systems with minimal differences between them, while the least adequate were the Spanish (55.2%) and Clinical class (47.1%) systems. The NTCTCS staging system was found to be better than TNM in our population but, because of its simplicity and greater dissemination, the TNM appears to be recommended for staging of patients with differentiated thyroid carcinoma. Copyright © 2014 SEEN. Published by Elsevier España, S.L.U. All rights reserved.

Oral cavity squamous cell carcinoma: Role of pretreatment imaging and its influence on management

International Nuclear Information System (INIS)

Arya, S.; Rane, P.; Deshmukh, A.

2014-01-01

Squamous cell carcinoma (SCC) is the commonest malignancy in the oral cavity. The oral cavity has several subsites. Knowledge of the patterns of disease spread at each subsite with the impact on treatment and prognosis provides a deeper understanding of the role of imaging. Information from imaging helps accurate staging, assess resectability, and plan multimodality treatment. Mandibular erosion, posterior soft tissue extent, and perineural spread influence treatment and prognosis in gingival, buccal, and retromolar trigone (RMT) cancers. Multidetector computed tomography (MDCT) with multiplanar reformations and bone and soft tissue algorithms provides the highest specificity for bone erosion. Hard palate SCC is optimally imaged with contrast-enhanced magnetic resonance imaging (MRI) to detect perineural spread. In oral tongue and floor of the mouth (FOM) SCC, extrinsic muscle invasion, extension across the midline, extent of posterior and inferior spread, and proximity to the hyoid are issues that impact therapeutic options. Contrast-enhanced MRI is the optimal imaging method for staging the primary due to its superior soft tissue resolution. In oral tongue SCCs with tumour thickness ≤4 mm, elective neck dissection can be avoided. For nodal staging (N-staging), all imaging methods are comparable, but fall short of surgical staging. Sentinel lymph node biopsy has a promising role in N-staging. Positron emission tomography (PET)/integrated PET/CT has no role in evaluating the clinically negative neck. PET/CT has a role in pretreatment evaluation of advanced oral cavity SCC for depicting distant metastases and for mapping nodal extent in the clinically positive neck. Diffusion-weighted MRI, dynamic contrast-enhanced MRI, and CT perfusion have a potential role as baseline pretreatment studies for response assessment to chemoradiation in advanced oral cavity SCC. - Highlights: • Brief outline of treatment principles in oral cavity squamous cell carcinoma (OCSCC

Sequential enzymatic saccharification and fermentation of ionic liquid and organosolv pretreated agave bagasse for ethanol production

Energy Technology Data Exchange (ETDEWEB)

Pérez-Pimienta, Jose A. [Univ. Autonoma de Nayarit, Tepic (Mexico); Vargas-Tah, Alejandra [Univ. Nacional Autonoma de Mexico (UNAM), Cuernavaca (Mexico).; López-Ortega, Karla M. [Univ. Autonoma de Nayarit, Tepic (Mexico); Medina-López, Yessenia N. [Univ. Autonoma de Nayarit, Tepic (Mexico); Mendoza-Pérez, Jorge A. [Inst. Politecnico Nacional (IPN), Mexico City (Mexico); Avila, Sayeny [Joint BioEnergy Inst. (JBEI), Emeryville, CA (United States); Singh, Seema [Joint BioEnergy Inst. (JBEI), Emeryville, CA (United States); Sandia National Lab. (SNL-CA), Livermore, CA (United States); Simmons, Blake A. [Joint BioEnergy Inst. (JBEI), Emeryville, CA (United States); Sandia National Lab. (SNL-CA), Livermore, CA (United States); Loaces, Inés [Univ. Nacional Autonoma de Mexico (UNAM), Cuernavaca (Mexico).; Martinez, Alfredo [Univ. Nacional Autonoma de Mexico (UNAM), Cuernavaca (Mexico).

2016-11-16

Agave bagasse (AGB) has gained recognition as a drought-tolerant biofuel feedstock with high productivity in semiarid regions. A comparative analysis of ionic liquid (IL) and organosolv (OV) pretreatment technologies in AGB was performed using a sequential enzymatic saccharification and fermentation (SESF) strategy with cellulolytic enzymes and the ethanologenic Escherichia coli strain MS04. After pretreatment, 86% of xylan and 45% of lignin were removed from OV-AGB, whereas IL-AGB reduced lignin content by 28% and xylan by 50% when compared to the untreated biomass. High glucan ( > 90%) and xylan ( > 83%) conversion was obtained with both pretreated samples. During the fermentation stage (48 h), 12.1 and 12.7 kg of ethanol were produced per 100 kg of untreated AGB for IL and OV, respectively. These comparative analyses showed the advantages of SESF using IL and OV in a biorefinery configuration where a better understanding of AGB recalcitrance is key for future applications.

Surface pretreatments for medical application of adhesion

Directory of Open Access Journals (Sweden)

Weber Michael

2003-09-01

Full Text Available Abstract Medical implants and prostheses (artificial hips, tendono- and ligament plasties usually are multi-component systems that may be machined from one of three material classes: metals, plastics and ceramics. Typically, the body-sided bonding element is bone. The purpose of this contribution is to describe developments carried out to optimize the techniques , connecting prosthesis to bone, to be joined by an adhesive bone cement at their interface. Although bonding of organic polymers to inorganic or organic surfaces and to bone has a long history, there remains a serious obstacle in realizing long-term high-bonding strengths in the in vivo body environment of ever present high humidity. Therefore, different pretreatments, individually adapted to the actual combination of materials, are needed to assure long term adhesive strength and stability against hydrolysis. This pretreatment for metal alloys may be silica layering; for PE-plastics, a specific plasma activation; and for bone, amphiphilic layering systems such that the hydrophilic properties of bone become better adapted to the hydrophobic properties of the bone cement. Amphiphilic layering systems are related to those developed in dentistry for dentine bonding. Specific pretreatment can significantly increase bond strengths, particularly after long term immersion in water under conditions similar to those in the human body. The bond strength between bone and plastic for example can be increased by a factor approaching 50 (pealing work increasing from 30 N/m to 1500 N/m. This review article summarizes the multi-disciplined subject of adhesion and adhesives, considering the technology involved in the formation and mechanical performance of adhesives joints inside the human body.

Biorefining of wheat straw: accounting for the distribution of mineral elements in pretreated biomass by an extended pretreatment-severity equation.

Science.gov (United States)

Le, Duy Michael; Sørensen, Hanne R; Knudsen, Niels Ole; Schjoerring, Jan K; Meyer, Anne S

2014-01-01

Mineral elements present in lignocellulosic biomass feedstocks may accumulate in biorefinery process streams and cause technological problems, or alternatively can be reaped for value addition. A better understanding of the distribution of minerals in biomass in response to pretreatment factors is therefore important in relation to development of new biorefinery processes. The objective of the present study was to examine the levels of mineral elements in pretreated wheat straw in response to systematic variations in the hydrothermal pretreatment parameters (pH, temperature, and treatment time), and to assess whether it is possible to model mineral levels in the pretreated fiber fraction. Principal component analysis of the wheat straw biomass constituents, including mineral elements, showed that the recovered levels of wheat straw constituents after different hydrothermal pretreatments could be divided into two groups: 1) Phosphorus, magnesium, potassium, manganese, zinc, and calcium correlated with xylose and arabinose (that is, hemicellulose), and levels of these constituents present in the fiber fraction after pretreatment varied depending on the pretreatment-severity; and 2) Silicon, iron, copper, aluminum correlated with lignin and cellulose levels, but the levels of these constituents showed no severity-dependent trends. For the first group, an expanded pretreatment-severity equation, containing a specific factor for each constituent, accounting for variability due to pretreatment pH, was developed. Using this equation, the mineral levels could be predicted with R(2) > 0.75; for some with R(2) up to 0.96. Pretreatment conditions, especially pH, significantly influenced the levels of phosphorus, magnesium, potassium, manganese, zinc, and calcium in the resulting fiber fractions. A new expanded pretreatment-severity equation is proposed to model and predict mineral composition in pretreated wheat straw biomass.

Innovative pretreatment strategies for biogas production.

Science.gov (United States)

Patinvoh, Regina J; Osadolor, Osagie A; Chandolias, Konstantinos; Sárvári Horváth, Ilona; Taherzadeh, Mohammad J

2017-01-01

Biogas or biomethane is traditionally produced via anaerobic digestion, or recently by thermochemical or a combination of thermochemical and biological processes via syngas (CO and H 2 ) fermentation. However, many of the feedstocks have recalcitrant structure and are difficult to digest (e.g., lignocelluloses or keratins), or they have toxic compounds (such as fruit flavors or high ammonia content), or not digestible at all (e.g., plastics). To overcome these challenges, innovative strategies for enhanced and economically favorable biogas production were proposed in this review. The strategies considered are commonly known physical pretreatment, rapid decompression, autohydrolysis, acid- or alkali pretreatments, solvents (e.g. for lignin or cellulose) pretreatments or leaching, supercritical, oxidative or biological pretreatments, as well as combined gasification and fermentation, integrated biogas production and pretreatment, innovative biogas digester design, co-digestion, and bio-augmentation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of EDTA and phosphoric Acid pretreatment on the bonding effectiveness of self-etch adhesives to ground enamel.

Science.gov (United States)

Ibrahim, Ihab M; Elkassas, Dina W; Yousry, Mai M

2010-10-01

This in vitro study determined the effect of enamel pretreatment with phosphoric acid and ethylenediaminetetraacetic acid (EDTA) on the bond strength of strong, intermediary strong, and mild self-etching adhesive systems. Ninety sound human premolars were used. Resin composite cylinders were bonded to flat ground enamel surfaces using three self-etching adhesive systems: strong Adper Prompt L-Pop (pH=0.9-1.0), intermediary strong AdheSE (pH=1.6-1.7), and mild Frog (pH=2). Adhesive systems were applied either according to manufacturer instructions (control) or after pretreatment with either phosphoric acid or EDTA (n=10). After 24 hours, shear bond strength was tested using a universal testing machine at a cross-head speed of 0.5 mm/minute. Ultra-morphological characterization of the surface topography and resin/enamel interfaces as well as representative fractured enamel specimens were examined using scanning electron microscopy (SEM). Neither surface pretreatment statistically increased the mean shear bond strength values of either the strong or the intermediary strong self-etching adhesive systems. However, phosphoric acid pretreatment significantly increased the mean shear bond strength values of the mild self-etching adhesive system. SEM examination of enamel surface topography showed that phosphoric acid pretreatment deepened the same etching pattern of the strong and intermediary strong adhesive systems but converted the irregular etching pattern of the mild self-etching adhesive system to a regular etching pattern. SEM examination of the resin/enamel interface revealed that deepening of the etching pattern was consistent with increase in the length of resin tags. EDTA pretreatment had a negligible effect on ultra-morphological features. Use of phosphoric acid pretreatment can be beneficial with mild self-etching adhesive systems for bonding to enamel.

Proposal for a new staging system for osteoradionecrosis of the mandible

NARCIS (Netherlands)

Karagozoglu, K.H.; Dekker, H.; Rietveld, D.H.F.; de Bree, R.; Schulten, E.A.J.M.; Kantola, S.; Forouzanfar, T.; van der Waal, I.

2014-01-01

The presented staging system seems well reproducible, facilitating the comparison of study groups dealing with the various issues of osteoradionecrosis of the mandible. It is yet to be evaluated whether the presently proposed staging system is useful for management purposes.

Evaluation of hydrogen and methane production from sugarcane bagasse hemicellulose hydrolysates by two-stage anaerobic digestion process.

Science.gov (United States)

Baêta, Bruno Eduardo Lobo; Lima, Diego Roberto Sousa; Filho, José Gabriel Balena; Adarme, Oscar Fernando Herrera; Gurgel, Leandro Vinícius Alves; Aquino, Sérgio Francisco de

2016-10-01

This study aimed at optimizing the net energy recovery from hydrogen and methane production through anaerobic digestion of the hemicellulose hydrolysate (HH) obtained by desirable conditions (DC) of autohydrolysis pretreatment (AH) of sugarcane bagasse (SB). Anaerobic digestion was carried out in a two-stage (acidogenic-methanogenic) batch system where the acidogenic phase worked as a hydrolysis and biodetoxification step. This allowed the utilization of more severe AH pretreatment conditions, i.e. T=178.6°C and t=55min (DC3) and T=182.9°C and t=40.71min (DC4). Such severe conditions resulted in higher extraction of hemicelluloses from SB (DC1=68.07%, DC2=48.99%, DC3=77.40% and DC4=73.90%), which consequently improved the net energy balance of the proposed process. The estimated energy from the combustion of both biogases (H2 and CH4) accumulated during the two-stage anaerobic digestion of HH generated by DC4 condition was capable of producing a net energy of 3.15MJ·kgSB(-1)dry weight. Copyright © 2016 Elsevier Ltd. All rights reserved.

SLS Block 1-B and Exploration Upper Stage Navigation System Design

Science.gov (United States)

Oliver, T. Emerson; Park, Thomas B.; Smith, Austin; Anzalone, Evan; Bernard, Bill; Strickland, Dennis; Geohagan, Kevin; Green, Melissa; Leggett, Jarred

2018-01-01

The SLS Block 1B vehicle is planned to extend NASA's heavy lift capability beyond the initial SLS Block 1 vehicle. The most noticeable change for this vehicle from SLS Block 1 is the swapping of the upper stage from the Interim Cryogenic Propulsion stage (ICPS), a modified Delta IV upper stage, to the more capable Exploration Upper Stage (EUS). As the vehicle evolves to provide greater lift capability and execute more demanding missions so must the SLS Integrated Navigation System to support those missions. The SLS Block 1 vehicle carries two independent navigation systems. The responsibility of the two systems is delineated between ascent and upper stage flight. The Block 1 navigation system is responsible for the phase of flight between the launch pad and insertion into Low-Earth Orbit (LEO). The upper stage system assumes the mission from LEO to payload separation. For the Block 1B vehicle, the two functions are combined into a single system intended to navigate from ground to payload insertion. Both are responsible for self-disposal once payload delivery is achieved. The evolution of the navigation hardware and algorithms from an inertial-only navigation system for Block 1 ascent flight to a tightly coupled GPS-aided inertial navigation system for Block 1-B is described. The Block 1 GN&C system has been designed to meet a LEO insertion target with a specified accuracy. The Block 1-B vehicle navigation system is designed to support the Block 1 LEO target accuracy as well as trans-lunar or trans-planetary injection accuracy. This is measured in terms of payload impact and stage disposal requirements. Additionally, the Block 1-B vehicle is designed to support human exploration and thus is designed to minimize the probability of Loss of Crew (LOC) through high-quality inertial instruments and Fault Detection, Isolation, and Recovery (FDIR) logic. The preliminary Block 1B integrated navigation system design is presented along with the challenges associated with

A Lymph Node Staging System for Gastric Cancer: A Hybrid Type Based on Topographic and Numeric Systems.

Directory of Open Access Journals (Sweden)

Yoon Young Choi

Full Text Available Although changing a lymph node staging system from an anatomically based system to a numerically based system in gastric cancer offers better prognostic performance, several problems can arise: it does not offer information on the anatomical extent of disease and cannot represent the extent of lymph node dissection. The purpose of this study was to discover an alternative lymph node staging system for gastric cancer. Data from 6025 patients who underwent gastrectomy for primary gastric cancer between January 2000 and December 2010 were reviewed. The lymph node groups were reclassified into lesser-curvature, greater-curvature, and extra-perigastric groups. Presence of any metastatic lymph node in one group was considered positive. Lymph node groups were further stratified into four (new N0-new N3 according to the number of positive lymph node groups. Survival outcomes with this new N staging were compared with those of the current TNM system. For validation, two centers in Japan (large center, n = 3443; medium center, n = 560 were invited. Even among the same pN stages, the more advanced new N stage showed worse prognosis, indicating that the anatomical extent of metastatic lymph nodes is important. The prognostic performance of the new staging system was as good as that of the current TNM system for overall advanced gastric cancer as well as lymph node-positive gastric cancer (Harrell C-index was 0.799, 0.726, and 0.703 in current TNM and 0.799, 0.727, and 0.703 in new TNM stage. Validation sets supported these outcomes. The new N staging system demonstrated prognostic performance equal to that of the current TNM system and could thus be used as an alternative.

EVALUATION OF NANOFILTRATION PRETREATMENTS FOR FLUX LOSS CONTROL

Science.gov (United States)

Differing nanofiltration pretreatment approaches for Ohio River water were evaluated withthe intent of producing systems with varying degrees of biological fouling. The membrane feed water was alum-coagulated, settled, and filtered Ohio River water (SF-ORW). Five 1.8" x 12" N...

Shear bond strength of one-step self-etch adhesives to dentin: Evaluation of NaOCl pretreatment.

Science.gov (United States)

Colombo, Marco; Beltrami, Riccardo; Chiesa, Marco; Poggio, Claudio; Scribante, Andrea

2018-02-01

The aim of this study was to evaluate the influence of dentin pretreatment with NaOCl on shear bond strength of four one-step self-etch adhesives with different pH values. Bovine permanent incisors were used. Four one-step self-etch adhesives were tested: Adper™ Easy Bond, Futurabond NR, G-aenial Bond, Clearfil S3 Bond. One two-step self-etch adhesive (Clearfil SE Bond) was used as control. Group 1- no pretreatment; group 2- pretratment with 5,25 % NaOCl; group 3- pretreatment with 37 % H3PO4 etching and 5,25 % NaOCl. A hybrid composite resin was inserted into the dentin surface. The specimens were tested in a universal testing machine. The examiners evaluated the fractured surfaces in optical microscope to determine failure modes, quantified with adhesive remnant index (ARI). Dentin pretreatment variably influenced bond strength values of the different adhesive systems. When no dentin pretreatment was applied, no significant differences were found ( P >.05) among four adhesives tested. No significant differences were recorded when comparing NaOCl pretreatment with H3PO4 + NaOCl pretreatment for all adhesive tested ( P >.05) except Clearfil S3 Bond that showed higher shear bond strength values when H3PO4 was applied. Frequencies of ARI scores were calculated. The influence of dentin pretreatment with NaOCl depends on the composition of each adhesive system used. There was no difference in bond strength values among self-etch adhesives with different pH values. Key words: Dentin, pretreatment, self-etch adhesives.

Permitting plan for project W-236B, initial pretreatment module

International Nuclear Information System (INIS)

Tollefson, K.S.

1995-01-01

The Tank Waste Remediation System pretreatment process mission is to separate high-level and low-level waste fractions. A comprehensive review of environmental regulations has indicated that several environmental reviews, permits, and approvals are required before construction and operation of the facility. This revised document provides a summary of permit application data requirements, alternative strategies for permit completion and approval, as well as the probability of success for each alternative for the Initial Pretreatment Module resulting from recent revisions to the Tri-Party Agreement

Hydrolytic pretreatment of oily wastewater by immobilized lipase.

Science.gov (United States)

Jeganathan, Jeganaesan; Nakhla, George; Bassi, Amarjeet

2007-06-25

The purpose of this study was to evaluate the hydrolysis of wastewater with high oil and grease (O&G) concentration from a pet food industry using immobilized lipase (IL) as a pretreatment step for anaerobic treatment through batch and continuous-flow experiments. The intrinsic Michaelis constant (K(m)) and maximum reaction rate (V(max)) were estimated experimentally and the K(m) value of IL (22.5g O&G/L) was six-folds higher than that of the free lipase (FL) (3.6gO&G/L), whereas V(max) of both FL (31.3mM/gmin) and IL (33.1mM/gmin) were similar. Preliminary batch anaerobic respirometric experiments showed that chemical oxygen demand (COD) and O&G reduction were 49 and 45% without pretreatment and 65 and 64% with IL pretreatment respectively, while the maximum growth rate (micromax) for pretreated wastewater (0.17d(-1)) was 3.4-folds higher than that of raw wastewater (0.05d(-1)) with similar Monod half-saturation constants (K(s) approximately 2.7gCOD/L). The continuous-flow experimental study showed the feasibility of employing the hybrid packed bed reactor (PBR)-upflow anaerobic sludge blanket (UASB) system for the treatment of high-strength oily wastewater, as reflected by its ability to operate at an oil loading rate (LR) of 4.9kgO&G/m(3)d (to the PBR) without any problems for a period of 100days. During pseudo-steady-state conditions, the hybrid UASB produced relatively higher biogas compared to the control UASB, The effluent COD and O&G concentrations of hybrid system were 100mg/L lower than that of the control UASB reactor and no foam production was observed in the hybrid UASB compared to the control UASB reactor.

Hydrolytic pretreatment of oily wastewater by immobilized lipase

International Nuclear Information System (INIS)

Jeganathan, Jeganaesan; Nakhla, George; Bassi, Amarjeet

2007-01-01

The purpose of this study was to evaluate the hydrolysis of wastewater with high oil and grease (O and G) concentration from a pet food industry using immobilized lipase (IL) as a pretreatment step for anaerobic treatment through batch and continuous-flow experiments. The intrinsic Michaelis constant (K m ) and maximum reaction rate (V max ) were estimated experimentally and the K m value of IL (22.5 g O and G/L) was six-folds higher than that of the free lipase (FL) (3.6 g O and G/L), whereas V max of both FL (31.3 mM/g min) and IL (33.1 mM/g min) were similar. Preliminary batch anaerobic respirometric experiments showed that chemical oxygen demand (COD) and O and G reduction were 49 and 45% without pretreatment and 65 and 64% with IL pretreatment respectively, while the maximum growth rate (μ max ) for pretreated wastewater (0.17 d -1 ) was 3.4-folds higher than that of raw wastewater (0.05 d -1 ) with similar Monod half-saturation constants (K s ∼ 2.7 g COD/L). The continuous-flow experimental study showed the feasibility of employing the hybrid packed bed reactor (PBR)-upflow anaerobic sludge blanket (UASB) system for the treatment of high-strength oily wastewater, as reflected by its ability to operate at an oil loading rate (LR) of 4.9 kg O and G/m 3 d (to the PBR) without any problems for a period of 100 days. During pseudo-steady-state conditions, the hybrid UASB produced relatively higher biogas compared to the control UASB, The effluent COD and O and G concentrations of hybrid system were 100 mg/L lower than that of the control UASB reactor and no foam production was observed in the hybrid UASB compared to the control UASB reactor

Reducing biomass recalcitrance via mild sodium carbonate pretreatment.

Science.gov (United States)

Mirmohamadsadeghi, Safoora; Chen, Zhu; Wan, Caixia

2016-06-01

This study examined the effects of mild sodium carbonate (Na2CO3) pretreatment on enzymatic hydrolysis of different feedstocks (i.e., corn stover, Miscanthus, and switchgrass). The results showed that sodium carbonate pretreatment markedly enhanced the sugar yields of the tested biomass feedstocks. The pretreated corn stover, Miscanthus, and switchgrass gave the glucose yields of 95.1%, 62.3%, and 81.3%, respectively, after enzymatic hydrolysis. The above glucose yields of pretreated feedstocks were 2-4 times that of untreated ones. The pretreatment also enhanced the xylose yields, 4 times for corn stover and 20 times for both Miscanthus and switchgrass. Sodium carbonate pretreatment removed 40-59% lignin from the tested feedstocks while preserving most of cellulose (sodium carbonate pretreatment was effective for reducing biomass recalcitrance and subsequently improving the digestibility of lignocellulosic biomass. Copyright © 2016 Elsevier Ltd. All rights reserved.

Self-tuning in master-slave synchronization of high-precision stage systems

NARCIS (Netherlands)

Heertjes, M.F.; Temizer, B.; Schneiders, M.G.E.

2013-01-01

For synchronization of high-precision stage systems, in particular the synchronization between a wafer and a reticle stage system of a wafer scanner, a master–slave controller design is presented. The design consists of a synchronization controller based on FIR filters and a data-driven self-tuning

The characteristic changes of betung bamboo (Dendrocalamus asper pretreated by fungal pretreatment

Directory of Open Access Journals (Sweden)

Widya Fatriasari

2014-05-01

Full Text Available Normal 0 false false false IN X-NONE X-NONE MicrosoftInternetExplorer4 The fungal pretreatment effect on chemical structural and morphological changes of Betung Bamboo was evaluated based on its biomass components after being cultivated by white rot fungi, Trametes versicolor. Betung bamboo powder (15 g was exposed to liquid inoculum of white rot fungi and incubated at 270C for 15, 30 and 45 days. The treated samples were then characterized by FT-IR spectroscopy, X-Ray diffraction and SEM-EDS analyses. Cultivation for 30 days with 5 and 10% loadings retained greater selectivity compared to that of the other treatments. FTIR spectra demonstrated that the fungus affected the decreasing of functional group quantities without changing the functional groups. The decrease in intensity at wave number of 1246 cm-1 (guaiacyl of lignin was greater than that at wave number of 1328 cm-1 (deformation combination of syringyl and xylan after fungal treatment. X-ray analysis showed the pretreated samples had a higher crystallinity than the untreated ones which might be due to the cleavage of amorphous fractions of cellulose. The pretreated samples have more fragile than the untreated ones confirmed by SEM. Crystalline allomorph calculated by XRD analysis showed that fungus pretreatment for 30 days has transformed triclinic structure of cellulose to monoclinic structure.

Comparison of two-stage thermophilic (68 degrees C/55 degrees C) anaerobic digestion with one-stage thermophilic (55 degrees C) digestion of cattle manure.

Science.gov (United States)

Nielsen, H B; Mladenovska, Z; Westermann, P; Ahring, B K

2004-05-05

A two-stage 68 degrees C/55 degrees C anaerobic degradation process for treatment of cattle manure was studied. In batch experiments, an increase of the specific methane yield, ranging from 24% to 56%, was obtained when cattle manure and its fractions (fibers and liquid) were pretreated at 68 degrees C for periods of 36, 108, and 168 h, and subsequently digested at 55 degrees C. In a lab-scale experiment, the performance of a two-stage reactor system, consisting of a digester operating at 68 degrees C with a hydraulic retention time (HRT) of 3 days, connected to a 55 degrees C reactor with 12-day HRT, was compared with a conventional single-stage reactor running at 55 degrees C with 15-days HRT. When an organic loading of 3 g volatile solids (VS) per liter per day was applied, the two-stage setup had a 6% to 8% higher specific methane yield and a 9% more effective VS-removal than the conventional single-stage reactor. The 68 degrees C reactor generated 7% to 9% of the total amount of methane of the two-stage system and maintained a volatile fatty acids (VFA) concentration of 4.0 to 4.4 g acetate per liter. Population size and activity of aceticlastic methanogens, syntrophic bacteria, and hydrolytic/fermentative bacteria were significantly lower in the 68 degrees C reactor than in the 55 degrees C reactors. The density levels of methanogens utilizing H2/CO2 or formate were, however, in the same range for all reactors, although the degradation of these substrates was significantly lower in the 68 degrees C reactor than in the 55 degrees C reactors. Temporal temperature gradient electrophoresis profiles (TTGE) of the 68 degrees C reactor demonstrated a stable bacterial community along with a less divergent community of archaeal species. Copyright 2004 Wiley Periodicals, Inc.

Parachute systems for the atmospheric reentry of launcher upper stages

Directory of Open Access Journals (Sweden)

Bogdan DOBRESCU

2017-03-01

Full Text Available Parachute systems can be used to control the reentry trajectory of launcher upper stages, in order to lower the risks to the population or facilitate the retrieval of the stage. Several types of parachutes deployed at subsonic, supersonic and hypersonic speeds are analyzed, modeled as single and multistage systems. The performance of deceleration parachutes depends on their drag area and deployment conditions, while gliding parachutes are configured to achieve stable flight with a high glide ratio. Gliding parachutes can be autonomously guided to a low risk landing area. Sizing the canopy is shown to be an effective method to reduce parachute sensitivity to wind. The reentry trajectory of a launcher upper stage is simulated for each parachute system configuration and the results are compared to the nominal reentry case.

Comparison of the performance between portal dosimetry and a commercial two-dimensional array system on pretreatment quality assurance for volumetric-modulated arc and intensity-modulated radiation therapy

International Nuclear Information System (INIS)

Kim, Yon-Lae; Chung, Jin-Beom; Kim, Jae-Sung; Lee, Jeong-Woo; Choi, Kyoung-Sik

2014-01-01

The aim of this study was to compare the dosimetric performance and to evaluate the pretreatment quality assurance (QA) of a portal dosimetry and a commercial two-dimensional (2-D) array system. In the characteristics comparison study, the measured values for the dose linearity, dose rate response, reproducibility, and field size dependence for 6-MV photon beams were analyzed for both detector systems. To perform the qualitative evaluations of the 10 IMRT and the 10 VMAT plans, we used the Gamma index for quantifying the agreement between calculations and measurements. The performance estimates for both systems show that overall, minimal differences in the dosimetric characteristics exist between the Electron portal imaging device (EPID) and 2-D array system. In the qualitative analysis for pretreatment quality assurance, the EPID and 2-D array system yield similar passing rate results for the majority of clinical Intensity-modulated radiation therapy (IMRT) and Volumetric-modulated arc therapy (VMAT) cases. These results were satisfactory for IMRT and VMAT fields and were within the acceptable criteria of γ % ≤1, γ avg < 0.5. The EPDI and the 2-D array systems showed comparable dosimetric results. In this study, the results revealed both systems to be suitable for patient-specific QA measurements for IMRT and VMAT. We conclude that, depending on the status of clinic, both systems can be used interchangeably for routine pretreatment QA.

Comparison of the performance between portal dosimetry and a commercial two-dimensional array system on pretreatment quality assurance for volumetric-modulated arc and intensity-modulated radiation therapy

Energy Technology Data Exchange (ETDEWEB)

Kim, Yon-Lae [Choonhae College of Health Sciences, Ulsan (Korea, Republic of); The Catholic University of Korea, Seoul (Korea, Republic of); Chung, Jin-Beom; Kim, Jae-Sung [Seoul National University Bundang Hospital, Seongnam (Korea, Republic of); Lee, Jeong-Woo [Konkuk University Medical Center, Seoul (Korea, Republic of); Choi, Kyoung-Sik [SAM Anyang Hospital, Anyang (Korea, Republic of)

2014-04-15

The aim of this study was to compare the dosimetric performance and to evaluate the pretreatment quality assurance (QA) of a portal dosimetry and a commercial two-dimensional (2-D) array system. In the characteristics comparison study, the measured values for the dose linearity, dose rate response, reproducibility, and field size dependence for 6-MV photon beams were analyzed for both detector systems. To perform the qualitative evaluations of the 10 IMRT and the 10 VMAT plans, we used the Gamma index for quantifying the agreement between calculations and measurements. The performance estimates for both systems show that overall, minimal differences in the dosimetric characteristics exist between the Electron portal imaging device (EPID) and 2-D array system. In the qualitative analysis for pretreatment quality assurance, the EPID and 2-D array system yield similar passing rate results for the majority of clinical Intensity-modulated radiation therapy (IMRT) and Volumetric-modulated arc therapy (VMAT) cases. These results were satisfactory for IMRT and VMAT fields and were within the acceptable criteria of γ{sub %}≤1, γ{sub avg} < 0.5. The EPDI and the 2-D array systems showed comparable dosimetric results. In this study, the results revealed both systems to be suitable for patient-specific QA measurements for IMRT and VMAT. We conclude that, depending on the status of clinic, both systems can be used interchangeably for routine pretreatment QA.

Organic Carbon Reduction in Seawater Reverse Osmosis (SWRO) Plants, Jeddah, Saudi Arabia

KAUST Repository

Alshahri, Abdullah

2015-01-01

intake systems and pre-treatment stages in minimizing the concentrations of algae, bacteria, natural organic matter (NOM) and transparent exopolymer particles (TEP), in the feed water prior to pre-treatment, through the pre-treatment stages

The NxStage System One.

Science.gov (United States)

Clark, William R; Turk, Joseph E

2004-01-01

Given the results of recent randomized controlled trials as well as staffing and budget challenges that today face many institutions across North America, a novel therapeutic approach is likely necessary to enable improvements in clinical outcomes for renal failure patients. The NxStage System One was developed to address these challenges. The system is an innovative, flexible device that delivers hemodialysis, hemofiltration, and/or ultrafiltration therapies to patients with renal failure or fluid overload. The unique characteristics of this system include a highly automated system design with a drop-in cartridge to facilitate training and simple operation; portable size and independence from dedicated infrastructure to minimize practical barriers to where therapy may be administered; use of high-quality premixed treatment fluids to enable capture of the potential clinical benefits of fluid purity without the hassles of local water treatment; and wide operating ranges to allow clinician flexibility in patient therapy prescriptions. In both the chronic and acute care environments, the System One presents clinicians with a new platform for delivering patient therapy improvements within real-world constraints.

Attenuation of methamphetamine-induced nigrostriatal dopaminergic neurotoxicity in mice by lipopolysaccharide pretreatment.

Science.gov (United States)

Lin, Yin Chiu; Kuo, Yu-Min; Liao, Pao-Chi; Cherng, Chianfang G; Su, Su-Wen; Yu, Lung

2007-04-30

Immunological activation has been proposed to play a role in methamphetamine-induced dopaminergic terminal damage. In this study, we examined the roles of lipopolysaccharide, a pro-inflammatory and inflammatory factor, treatment in modulating the methamphetamine-induced nigrostriatal dopamine neurotoxicity. Lipopolysaccharide pretreatment did not affect the basal body temperature or methamphetamine-elicited hyperthermia three days later. Such systemic lipopolysaccharide treatment mitigated methamphetamine-induced striatal dopamine and 3,4-dihydroxyphenylacetic acid depletions in a dose-dependent manner. As the most potent dose (1 mg/kg) of lipopolysaccharide was administered two weeks, one day before or after the methamphetamine dosing regimen, methamphetamine-induced striatal dopamine and 3,4-dihydroxyphenylacetic acid depletions remained unaltered. Moreover, systemic lipopolysaccharide pretreatment (1 mg/kg) attenuated local methamphetamine infusion-produced dopamine and 3,4-dihydroxyphenylacetic acid depletions in the striatum, indicating that the protective effect of lipopolysaccharide is less likely due to interrupted peripheral distribution or metabolism of methamphetamine. We concluded a critical time window for systemic lipopolysaccharide pretreatment in exerting effective protection against methamphetamine-induced nigrostriatal dopamine neurotoxicity.

Wind Solar Hybrid System Rectifier Stage Topology Simulation

OpenAIRE

Anup M. Gakare; Subhash Kamdi

2014-01-01

This paper presents power-control strategies of a grid-connected hybrid generation system with versatile power transfer. The hybrid system allows maximum utilization of freely available renewable sources like wind and photovoltaic energies. This paper presents a new system configuration of the multi input rectifier stage for a hybrid wind and photovoltaic energy system. This configuration allows the two sources to supply the load simultaneously depending on the availability of...

Evaluation of the 8th AJCC staging system for pathologically versus clinically staged pancreatic adenocarcinoma: A time to revisit a dogma?

Science.gov (United States)

Abdel-Rahman, Omar

2018-02-01

The 8th edition of the American Joint Committee on Cancer (AJCC) staging system for pancreatic exocrine adenocarcinoma has been released. The current study seeks to assess the 7th and 8th editions among patients registered within the surveillance, epidemiology and end results (SEER) database. SEER database (2010-2013) has been accessed through SEER*Stat program and AJCC 8th edition stages were reconstructed utilizing the collaborative stage descriptions. Kaplan-Meier analysis of overall survival and pancreatic cancer-specific survival analyses (according to both 7th and 8th editions and according to whether pathological or clinical staging were conducted) has been performed. Multivariate analysis of factors affecting pancreatic cancer-specific survival was also conducted through a Cox proportional hazard model. A total of 18  948 patients with pancreatic adenocarcinoma were identified in the period from 2010-2013. Pancreatic cancer-specific survival among pathologically staged patients and according to the 8th edition showed significant differences for all pair wise comparisons among different stages (P < 0.0001) except for the comparison between stage IA and stage IB (P = 0.307) and the comparison between stage IB and stage IIA (P = 0.116). Moreover, P value for stage IA vs IIA was 0.014; while pancreatic cancer-specific survival according to the 7th edition among pathologically staged patients showed significant differences for all pair wise comparisons among different stages (P < 0.0001) except for the comparison between IA and IB (P = 0.072), the comparison between stage IIA and stage IIB (P = 0.065), the comparison between stage IIA and stage III (P = 0.059) and the comparison between IIB and III (P = 0.595). Among clinically staged patients (i.e. those who did not undergo initial radical surgery), the prognostic performance of both 7th and 8th stages for both overall survival and pancreatic cancer-specific survival was

Hydrodynamic cavitation as a strategy to enhance the efficiency of lignocellulosic biomass pretreatment

DEFF Research Database (Denmark)

Terán Hilares, Ruly; Ramos, Lucas; da Silva, Silvio Silvério

2018-01-01

to accelerate certain chemical reactions. The application of cavitation energy to enhance the efficiency of lignocellulosic biomass pretreatment is an interesting strategy proposed for integration in biorefineries for the production of bio-based products. Moreover, the use of an HC-assisted process...... was demonstrated as an attractive alternative when compared to other conventional pretreatment technologies. This is not only due to high pretreatment efficiency resulting in high enzymatic digestibility of carbohydrate fraction, but also, by its high energy efficiency, simple configuration, and construction...... of systems, besides the possibility of using on the large scale. This paper gives an overview regarding HC technology and its potential for application on the pretreatment of lignocellulosic biomass. The parameters affecting this process and the perspectives for future developments in this area are also...

A Thermoelectric Generation System and Its Power Electronics Stage

DEFF Research Database (Denmark)

Gao, Junling; Sun, Kai; Ni, Longxian

2012-01-01

stage and signal-conditioning circuits of the load, including DC–DC conversion, the maximum power point tracking (MPPT) controller, and other power management controllers. In this paper, a survey of existing power electronics designs for TEG systems is presented first. Second, a flat, wall-like TEG...... system consisting of 32 modules is experimentally optimized, and the improved power parameters are tested. Power-conditioning circuitry based on an interleaved boost DC–DC converter is then developed for the TEG system in terms of the tested power specification. The power electronics design features...... a combined control scheme with an MPPT and a constant output voltage as well as the low-voltage and high-current output characteristics of the TEG system. The experimental results of the TEG system with the power electronics stage and with purely resistive loads are compared. The comparisons verify...

Enzymatic hydrolysis of pretreated soybean straw

International Nuclear Information System (INIS)

Xu Zhong; Wang Qunhui; Jiang Zhaohua; Yang Xuexin; Ji Yongzhen

2007-01-01

In order to produce lactic acid, from agricultural residues such as soybean straw, which is a raw material for biodegradable plastic production, it is necessary to decompose the soybean straw into soluble sugars. Enzymatic hydrolysis is one of the methods in common use, while pretreatment is the effective way to increase the hydrolysis rate. The optimal conditions of pretreatment using ammonia and enzymatic hydrolysis of soybean straw were determined. Compared with the untreated straw, cellulose in straw pretreated by ammonia liquor (10%) soaking for 24 h at room temperature increased 70.27%, whereas hemicellulose and lignin in pretreated straw decreased to 41.45% and 30.16%, respectively. The results of infrared spectra (IR), scanning electron microscope (SEM) and X-ray diffraction (XRD) analysis also showed that the structure and the surface of the straw were changed through pretreatment that is in favor of the following enzymatic hydrolysis. maximum enzymatic hydrolysis rate of 51.22% was achieved at a substrate concentration of 5% (w/v) at 50 deg. C and pH 4.8 using cellulase (50 fpu/g of substrate) for 36 h

Liver-inherent immune system: its role in blood-stage malaria.

Science.gov (United States)

Wunderlich, Frank; Al-Quraishy, Saleh; Dkhil, Mohamed A

2014-01-01

The liver is well known as that organ which is obligately required for the intrahepatocyte development of the pre-erythrocytic stages of the malaria-causative agent Plasmodium. However, largely neglected is the fact that the liver is also a central player of the host defense against the morbidity- and mortality-causing blood stages of the malaria parasites. Indeed, the liver is equipped with a unique immune system that acts locally, however, with systemic impact. Its main "antipodal" functions are to recognize and to generate effective immunoreactivity against pathogens on the one hand, and to generate tolerance to avoid immunoreactivity with "self" and harmless substances as dietary compounds on the other hand. This review provides an introductory survey of the liver-inherent immune system: its pathogen recognition receptors including Toll-like receptors (TLRs) and its major cell constituents with their different facilities to fight and eliminate pathogens. Then, evidence is presented that the liver is also an essential organ to overcome blood-stage malaria. Finally, we discuss effector responses of the liver-inherent immune system directed against blood-stage malaria: activation of TLRs, acute phase response, phagocytic activity, cytokine-mediated pro- and anti-inflammatory responses, generation of "protective" autoimmunity by extrathymic T cells and B-1 cells, and T cell-mediated repair of liver injuries mainly produced by malaria-induced overreactions of the liver-inherent immune system.

Perineural invasion and Gleason 7-10 tumors predict increased failure in prostate cancer patients with pretreatment PSA <10 ng/ml treated with conformal external beam radiation therapy

International Nuclear Information System (INIS)

Anderson, Penny R.; Hanlon, Alexandra L.; Patchefsky, Arthur; Al-Saleem, Tahseen; Hanks, Gerald E.

1998-01-01

Purpose: It has been well established that prostate cancer patients with pretreatment PSA<10 ng/ml enjoy excellent bNED control when treated with definitive external beam radiation therapy. This report identifies predictors of failure for patients with pretreatment PSA <10 ng/ml. These predictors are then used to define favorable and unfavorable prognostic subgroups of patients for which bNED control is compared. Methods and Materials: Between 3/87 and 11/94, 266 patients with T1-T3NXM0 prostate cancer and pretreatment PSA values <10 ng/ml were treated with definitive external beam radiation therapy. Median central axis dose and median follow-up for the entire group was 72 Gy (63-79 Gy) and 48 months (2-120 months). Predictors of bNED control were evaluated univariately using Kaplan-Meier methodology and the log-rank test and multivariately using Cox proportional hazards modeling. Covariates considered were pretreatment PSA, palpation stage, Gleason score, presence of perineual invasion (PNI) and central axis dose. Independent predictors based on multivariate results were then used to stratify the patients into two prognostic groups for which bNED control was compared. bNED failure is defined as PSA ≥ 1.5 ng/ml and rising on two consecutive determinations. Results: Univariate analysis according to pretreatment and treatment factors for bNED control demonstrates a statistically significant improvement in 5-year bNED control for patients with Gleason score 2-6 vs. 7-10, patients without evidence of perineural invasion (PNI) vs. those with PNI, and patients with palpation stage T1/T2AB vs. T2C/T3. Multivariate analysis demonstrates that Gleason score (p = 0.0496), PNI (p = 0.0008) and palpation stage (p = 0.0153) are significant independent predictors of bNED control. Based on these factors, patients are stratified into a more favorable prognosis group (Gleason 2-6, no PNI, and stage T1/T2AB, n = 172) and a less favorable prognosis group (Gleason 7-10 or PNI or T2C

Effectiveness of interim stage filter in the exhaust system of glove boxes

International Nuclear Information System (INIS)

Patre, D.K.; Vangara, H.; Thanamani, S.; Gopalakrishnan, R.K.; Mhatre, Amol M.

2018-01-01

All operations in radiochemical laboratories are carried out in containment systems like Glove boxes and Fume hoods. For controlling air contamination two separate air cleaning systems are incorporated. Laboratory has general ventilation system and glove boxes are provided with a negative pressure system (NPS). Glove box exhaust air is passed through three stage filtration systems: in situ, interim and final before discharging to the atmosphere. In addition to the individual HEPA filters of each glove box, there is an interim HEPA filter bank introduced at the laboratory end. This was introduced to reduce a load on main exhaust filter system. Finally the exhaust air is discharged through the final stage HEPA filter located in the filter house through the Stack. The interim HEPA filter bank provides additional protection for the release of particulate activity and reduces load on the final stage filters. In the present work efforts have been put to validate the interim stage filter, which has been introduced, to limit the environmental release

Coagulation and ultrafiltration in seawater reverse osmosis pretreatment

NARCIS (Netherlands)

Tabatabai, S.A.A.

2014-01-01

Seawater desalination is a globally expanding coastal industry with an installed capacity of over 80 million m3/day. Algal blooms pose a challenge to the operation of seawater reverse osmosis (SWRO) membranes and pre-treatment systems due to high concentrations of algal cells and algal organic

Determining if pretreatment PSA doubling time predicts PSA trajectories after radiation therapy for localized prostate cancer

International Nuclear Information System (INIS)

Soto, Daniel E.; Andridge, Rebecca R.; Pan, Charlie C.; Williams, Scott G.; Taylor, Jeremy M.G.; Sandler, Howard M.

2009-01-01

Introduction: To determine if pretreatment PSA doubling time (PSA-DT) can predict post-radiation therapy (RT) PSA trajectories for localized prostate cancer. Materials and methods: Three hundred and seventy-five prostate cancer patients treated with external beam RT without androgen deprivation therapy (ADT) were identified with an adequate number of PSA values. We utilized a linear mixed model (LMM) analysis to model longitudinal PSA data sets after definitive treatment. Post-treatment PSA trajectories were allowed to depend on the pre-RT PSA-DT, pre-RT PSA (iPSA), Gleason score (GS), and T-stage. Results: Pre-RT PSA-DT had a borderline impact on predicting the rate of PSA rise after nadir (p = 0.08). For a typical low risk patient (T1, GS ≤ 6, iPSA 10), the predicted PSA-DT post-nadir was 21% shorter for pre-RT PSA-DT 24 month (19 month vs. 24 month). Additional significant predictors of post-RT PSA rate of rise included GS (p < 0.0001), iPSA (p < 0.0001), and T-stage (p = 0.02). Conclusions: We observed a trend between rapidly rising pre-RT PSA and the post-RT post-nadir PSA rise. This effect appeared to be independent of iPSA, GS, or T-stage. The results presented suggest that pretreatment PSA-DT may help predict post-RT PSA trajectories

Theoretical study for solar air pretreatment collector/regenerator

Energy Technology Data Exchange (ETDEWEB)

Peng Donggen; Zhang Xiaosong; Yin Yonggao [School of Energy and Environment, Southeast Univ., Nanjing (China)

2008-07-01

A new liquid regeneration equipment - solar air pretreatment collector/regenerator for liquid desiccant cooling system is put forward in this paper, which is preferable to solution regeneration in hot and moist climate in South China. The equipment can achieve liquid regeneration in lower temperature. When the solution and the air are in ''match'' state in collector/ regenerator, a match air to salt mass ratio ASMR* is found by theoretical study in which there is the largest theoretical storage capacity SC{sub max}. After two new concepts of the effective solution proportion (EPS) and the effective storage capacity (ESC) are defined, it is found by theoretical calculation that when ESP drops from 100% to 67%, ESC raises lowly, not drops and liquid outlet concentration C{sub str} {sub sol} increases from 40% to 49% in which its increment totals to 90%. All these data explain fully that air pretreatment liquid regeneration equipment enables to improve the performance of liquid desiccant cooling system. (orig.)

Radiation dose response in patients with favorable localized prostate cancer (Stage T1-T2, biopsy Gleason ≤6, and pretreatment prostate-specific antigen ≤10)

International Nuclear Information System (INIS)

Kupelian, Patrick A.; Buchsbaum, Jeffrey C.; Reddy, Chandana A.; Klein, Eric A.

2001-01-01

Purpose: To study the radiation dose response as determined by biochemical relapse-free survival in patients with favorable localized prostate cancers, i.e., Stage T1-T2, biopsy Gleason score (bGS) ≤6, and pretreatment prostate-specific antigen (iPSA) ≤10 ng/mL. Methods and Materials: A total of 292 patients with favorable localized prostate cancer were treated with radiotherapy alone between 1986 and 1999. The median age was 69 years. Sixteen percent of cases (n=46) were African-American. The distribution by clinical T stage was as follows: T1/T2A, 243 (83%); and T2B/T2C, 49 (17%). The distribution by iPSA was as follows: ≤4 ng/mL, 49 (17%); and >4 ng/mL, 243 (83%). The mean iPSA level was 6.2 (median, 6.4). The distribution by bGS was as follows: ≤5 in 89 cases (30%) and 6 in 203 cases (70%). The median radiation dose was 70.0 Gy (range, 63.0-78.0 Gy). Doses of ≤70.0 Gy were delivered in 175 cases, 70.2-72.0 Gy in 24 cases, 74 Gy in 30 cases, and 78 Gy in 63 cases. For patients receiving 2 =5.7), and radiation dose (p=0.021, χ 2 =5.3) were independent predictors of outcome. Age (p=0.94), race (p=0.89), stage (p=0.45), biopsy GS (p=0.40), and radiation technique (p=0.45) were not. Conclusion: There is a clear radiation dose response in patients with favorable localized prostate cancers (i.e., Stage T1-T2, biopsy Gleason score ≤6, and iPSA ≤10 ng/mL). At least 74 Gy should be delivered to the prostate and periprostatic tissues. With our cohort of patients, longer follow-up will be needed to assess the importance of doses exceeding 74 Gy

The effect of wastewater pretreatment on nanofiltration membrane performance

Directory of Open Access Journals (Sweden)

Ali Hashlamon

2017-03-01

Full Text Available Membrane fouling is considered a serious obstacle for operation and cost efficiency in wastewater treatment using nanofiltration (NF. However, pretreatment is the most practical way to reduce this prior to NF. In this research, two types of wastewaters were pretreated with different methods prior to NF to examine the effect of pretreatment on membrane fouling in terms of turbidity, chemical oxygen demand (COD and permeate flux. Turbidity and COD were measured to assess solid foulants and organic species in the wastewater, respectively. The first sample was secondary treated sewage, which was pretreated using coagulation-flocculation-sedimentation (CFS only. Steady flux was increased from 24 L/m2h for wastewater without pretreatment to 32.1 L/m2h with pretreatment. COD was also eliminated after CFS/NF, and turbidity was reduced to 0.6 NTU. The second sample was diluted biodiesel wastewater, which was pretreated using a combination of powdered-activated carbon (PAC adsorption and CFS (PAC/CFS. Steady flux was increased from 22.3 L/m2h for wastewater without pretreatment to 28.7 L/m2h with pretreatment; biodiesel wastewater quality also improved. Turbidity was reduced from 12 to 0.6 NTU, and COD was reduced from 526 to 4 mg/L after NF with PAC/CFS pretreatment, while COD was reduced from 526 to 95 mg/L using NF without pretreatment.

Non-hypervascular hypointense nodules on Gd-EOB-DTPA-enhanced MRI as a predictor of outcomes for early-stage HCC.

Science.gov (United States)

Toyoda, Hidenori; Kumada, Takashi; Tada, Toshifumi; Sone, Yasuhiro; Maeda, Atsuyuki; Kaneoka, Yuji

2015-01-01

In patients with hepatocellular carcinoma (HCC), gadolinium-ethoxybenzyl-diethylenetriamine pentaacetic acid (Gd-EOB-DTPA)-enhanced magnetic resonance imaging (MRI) often identifies non-hypervascular hypointense hepatic nodules during the hepatobiliary phase, but their prognostic significance is unclear. We conducted a prospective observational study to investigate the impact of non-hypervascular hypointense hepatic nodules detected by Gd-EOB-DTPA-enhanced MRI on the outcome of patients with early-stage HCC. Post-treatment recurrence and survival rates were analyzed in 138 patients with non-recurrent, early-stage HCC [Barcelona Clinic Liver Cancer (BCLC) stage 0 or A] and Child-Pugh A liver function according to the presence of non-hypervascular hypointense nodules on pretreatment Gd-EOB-DTPA-enhanced MRI. Non-hypervascular hypointense hepatic nodules were detected in 51 (37.0%) patients with early-stage HCC on pretreatment Gd-EOB-DTPA-enhanced MRI. Recurrence rates were significantly higher in patients with non-hypervascular hypointense nodules (p DTPA-enhanced MRI was independently associated with an increased recurrence rate, independent of tumor progression or treatment (p = 0.0005). The survival rate was significantly lower in patients with non-hypervascular hypointense nodules on Gd-EOB-DTPA-enhanced MRI (p = 0.0108). In patients with early-stage typical HCC (BCLC 0 or A), the presence of concurrent non-hypervascular hypointense hepatic nodules in the hepatobiliary phase of pretreatment Gd-EOB-DTPA-enhanced MRI is an indicator of higher likelihood of recurrence after treatment and may be a marker for unfavorable outcome.

Direct Succinic Acid Production from Minimally Pretreated Biomass Using Sequential Solid-State and Slurry Fermentation with Mixed Fungal Cultures

Directory of Open Access Journals (Sweden)

Jerico Alcantara

2017-06-01

Full Text Available Conventional bio-based succinic acid production involves anaerobic bacterial fermentation of pure sugars. This study explored a new route for directly producing succinic acid from minimally-pretreated lignocellulosic biomass via a consolidated bioprocessing technology employing a mixed lignocellulolytic and acidogenic fungal co-culture. The process involved a solid-state pre-fermentation stage followed by a two-phase slurry fermentation stage. During the solid-state pre-fermentation stage, Aspergillus niger and Trichoderma reesei were co-cultured in a nitrogen-rich substrate (e.g., soybean hull to induce cellulolytic enzyme activity. The ligninolytic fungus Phanerochaete chrysosporium was grown separately on carbon-rich birch wood chips to induce ligninolytic enzymes, rendering the biomass more susceptible to cellulase attack. The solid-state pre-cultures were then combined in a slurry fermentation culture to achieve simultaneous enzymatic cellulolysis and succinic acid production. This approach generated succinic acid at maximum titers of 32.43 g/L after 72 h of batch slurry fermentation (~10 g/L production, and 61.12 g/L after 36 h of addition of fresh birch wood chips at the onset of the slurry fermentation stage (~26 g/L production. Based on this result, this approach is a promising alternative to current bacterial succinic acid production due to its minimal substrate pretreatment requirements, which could reduce production costs.

Structural properties, crystal quality and growth modes of MOCVD-grown AlN with TMAl pretreatment of sapphire substrate

KAUST Repository

Sun, Haiding; Wu, Feng; Altahtamouni, Talal Mohammed Ahmad; Alfaraj, Nasir; Li, Kun; Detchprohm, Theeradetch; Dupuis, Russell; Li, Xiaohang

2017-01-01

The growth of high quality AlN epitaxial films relies on precise control of the initial growth stages. In this work, we examined the influence of the trimethylaluminum (TMAl) pretreatment of sapphire substrates on the structural properties, crystal quality and growth modes of heteroepitaxial AlN films on (0001) sapphire substrates. Without the pretreatment, the AlN films nucleated on the smooth surface but exhibited mixed crystallographic Al- (N-) polarity, resulting in rough AlN film surfaces. With increasing the pretreatment time from 1 to 5 s, the N-polarity started to be impeded. However, small islands were formed on sapphire surface due to the decompostion of TMAl. As a result, small voids became noticeable at the nucleation layer (NL) because the growth started as quasi three-dimensional (3D) but transformed to 2D mode as the film grew thicker and got coalesced, leading to smoother and Al-polar films. On the other hand, longer pretreatment time of 40 s formed large 3D islands on sapphire, and thus initiated a 3D-growth mode of the AlN film, generating Al-polar AlN nanocolumns with different facets, which resulted into rougher film surfaces. The epitaxial growth modes and their correlation with the AlN film crystal quality under different TMAl pretreatments are also discussed.

Structural properties, crystal quality and growth modes of MOCVD-grown AlN with TMAl pretreatment of sapphire substrate

KAUST Repository

Sun, Haiding

2017-08-08

The growth of high quality AlN epitaxial films relies on precise control of the initial growth stages. In this work, we examined the influence of the trimethylaluminum (TMAl) pretreatment of sapphire substrates on the structural properties, crystal quality and growth modes of heteroepitaxial AlN films on (0001) sapphire substrates. Without the pretreatment, the AlN films nucleated on the smooth surface but exhibited mixed crystallographic Al- (N-) polarity, resulting in rough AlN film surfaces. With increasing the pretreatment time from 1 to 5 s, the N-polarity started to be impeded. However, small islands were formed on sapphire surface due to the decompostion of TMAl. As a result, small voids became noticeable at the nucleation layer (NL) because the growth started as quasi three-dimensional (3D) but transformed to 2D mode as the film grew thicker and got coalesced, leading to smoother and Al-polar films. On the other hand, longer pretreatment time of 40 s formed large 3D islands on sapphire, and thus initiated a 3D-growth mode of the AlN film, generating Al-polar AlN nanocolumns with different facets, which resulted into rougher film surfaces. The epitaxial growth modes and their correlation with the AlN film crystal quality under different TMAl pretreatments are also discussed.

Strategies for enzyme saving during saccharification of pretreated lignocellulo-starch biomass: effect of enzyme dosage and detoxification chemicals

Directory of Open Access Journals (Sweden)

M.G. Mithra

2017-08-01

Full Text Available Two strategies leading to enzyme saving during saccharification of pretreated lignocellulo-starch biomass (LCSB was investigated which included reducing enzyme dosage by varying their levels in enzyme cocktails and enhancing the fermentable sugar yield in enzyme-reduced systems using detoxification chemicals. Time course release of reducing sugars (RS during 24–120 h was significantly higher when an enzyme cocktail containing full dose of cellulase (16 FPU/g cellulose along with half dose each of xylanase (1.5 mg protein/g hemicelluloses and Stargen (12.5 μl/g biomass was used to saccharify conventional dilute sulphuric acid (DSA pretreated biomass compared to a parallel system where only one-fourth the dose of the latter two enzymes was used. The reduction in RS content in the 120 h saccharified mash to the extent of 3–4 g/L compared to the system saccharified with full complement of the three enzymes could be overcome considerably by supplementing the system (half dose of two enzymes with detoxification chemical mix incorporating Tween 20, PEG 4000 and sodium borohydride. Microwave (MW-assisted DSA pretreated biomass on saccharification with enzyme cocktail having full dose of cellulase and half dose of Stargen along with detoxification chemicals gave significantly higher RS yield than DSA pretreated system saccharified using three enzymes. The study showed that xylanase could be eliminated during saccharification of MW-assisted DSA pretreated biomass without affecting RS yield when detoxification chemicals were also supplemented. The Saccharification Efficiency and Overall Conversion Efficiency were also high for the MW-assisted DSA pretreated biomass. Since whole slurry saccharifcation of pretreated biomass is essential to conserve fermentable sugars in LCSB saccharification, detoxification of soluble inhibitors is equally important as channelling out of insoluble lignin remaining in the residue. As one of the major factors contributing

Alternatives generation and analysis for phase I intermediate waste feed staging system design requirements

Energy Technology Data Exchange (ETDEWEB)

Britton, M.D.

1996-10-02

This document provides; a decision analysis summary; problem statement; constraints, requirements, and assumptions; decision criteria; intermediate waste feed staging system options and alternatives generation and screening; intermediate waste feed staging system design concepts; intermediate waste feed staging system alternative evaluation and analysis; and open issues and actions.

A Gas-Spring-Loaded X-Y-Z Stage System for X-ray Microdiffraction Sample Manipulation

International Nuclear Information System (INIS)

Shu Deming; Cai Zhonghou; Lai, Barry

2007-01-01

We have designed and constructed a gas-spring-loaded x-y-z stage system for x-ray microdiffraction sample manipulation at the Advanced Photon Source XOR 2-ID-D station. The stage system includes three DC-motor-driven linear stages and a gas-spring-based heavy preloading structure, which provides antigravity forces to ensure that the stage system keeps high-positioning performance under variable goniometer orientation. Microdiffraction experiments with this new stage system showed significant sample manipulation performance improvement

A Three-Stage Optimal Approach for Power System Economic Dispatch Considering Microgrids

Directory of Open Access Journals (Sweden)

Wei-Tzer Huang

2016-11-01

Full Text Available The inclusion of microgrids (MGs in power systems, especially distribution-substation-level MGs, significantly affects power systems because of the large volumes of import and export power flows. Consequently, power dispatch has become complicated, and finding an optimal solution is difficult. In this study, a three-stage optimal power dispatch model is proposed to solve such dispatch problems. In the proposed model, the entire power system is divided into two parts, namely, the main power grid and MGs. The optimal power dispatch problem is resolved on the basis of multi-area concepts. In stage I, the main power system economic dispatch (ED problem is solved by sensitive factors. In stage II, the optimal power dispatches of the local MGs are addressed via an improved direct search method. In stage III, the incremental linear models for the entire power system can be established on the basis of the solutions of the previous two stages and can be subjected to linear programming to determine the optimal reschedules from the original dispatch solutions. The proposed method is coded using Matlab and tested by utilizing an IEEE 14-bus test system to verify its feasibility and accuracy. Results demonstrated that the proposed approach can be used for the ED of power systems with MGs as virtual power plants.

Determination of suitable microspore stage and callus induction from anthers of kenaf (Hibiscus cannabinus L.).

Science.gov (United States)

Ibrahim, Ahmed Mahmood; Kayat, Fatimah Binti; Hussin, Zeti Ermiena Surya Mat; Susanto, Dwi; Ariffulah, Mohammed

2014-01-01

Kenaf (Hibiscus cannabinus L.) is one of the important species of Hibiscus cultivated for fiber. Availability of homozygous parent lines is prerequisite to the use of the heterosis effect reproducible in hybrid breeding. The production of haploid plants by anther culture followed by chromosome doubling can be achieved in short period compared with inbred lines by conventional method that requires self pollination of parent material. In this research, the effects of the microspore developmental stage, time of flower collection, various pretreatments, different combinations of hormones, and culture condition on anther culture of KB6 variety of Kenaf were studied. Young flower buds with immature anthers at the appropriate stage of microspore development were sterilized and the anthers were carefully dissected from the flower buds and subjected to various pretreatments and different combinations of hormones like NAA, 2,4-D, Kinetin, BAP, and TDZ to induce callus. The best microspore development stage of the flower buds was about 6-8 mm long collected 1-2 weeks after flower initiation. At that stage, the microspores were at the uninucleate stage which was suitable for culture. The best callus induction frequency was 90% in the optimized semisolid MS medium fortified with 3.0 mg/L BAP + 3.0 mg/L NAA.

Determination of Suitable Microspore Stage and Callus Induction from Anthers of Kenaf (Hibiscus cannabinus L.

Directory of Open Access Journals (Sweden)

Ahmed Mahmood Ibrahim

2014-01-01

Full Text Available Kenaf (Hibiscus cannabinus L. is one of the important species of Hibiscus cultivated for fiber. Availability of homozygous parent lines is prerequisite to the use of the heterosis effect reproducible in hybrid breeding. The production of haploid plants by anther culture followed by chromosome doubling can be achieved in short period compared with inbred lines by conventional method that requires self pollination of parent material. In this research, the effects of the microspore developmental stage, time of flower collection, various pretreatments, different combinations of hormones, and culture condition on anther culture of KB6 variety of Kenaf were studied. Young flower buds with immature anthers at the appropriate stage of microspore development were sterilized and the anthers were carefully dissected from the flower buds and subjected to various pretreatments and different combinations of hormones like NAA, 2,4-D, Kinetin, BAP, and TDZ to induce callus. The best microspore development stage of the flower buds was about 6–8 mm long collected 1-2 weeks after flower initiation. At that stage, the microspores were at the uninucleate stage which was suitable for culture. The best callus induction frequency was 90% in the optimized semisolid MS medium fortified with 3.0 mg/L BAP + 3.0 mg/L NAA.

Determination of Suitable Microspore Stage and Callus Induction from Anthers of Kenaf (Hibiscus cannabinus L.)

Science.gov (United States)

Binti Kayat, Fatimah; Ermiena Surya Mat Hussin, Zeti; Susanto, Dwi; Ariffulah, Mohammed

2014-01-01

Kenaf (Hibiscus cannabinus L.) is one of the important species of Hibiscus cultivated for fiber. Availability of homozygous parent lines is prerequisite to the use of the heterosis effect reproducible in hybrid breeding. The production of haploid plants by anther culture followed by chromosome doubling can be achieved in short period compared with inbred lines by conventional method that requires self pollination of parent material. In this research, the effects of the microspore developmental stage, time of flower collection, various pretreatments, different combinations of hormones, and culture condition on anther culture of KB6 variety of Kenaf were studied. Young flower buds with immature anthers at the appropriate stage of microspore development were sterilized and the anthers were carefully dissected from the flower buds and subjected to various pretreatments and different combinations of hormones like NAA, 2,4-D, Kinetin, BAP, and TDZ to induce callus. The best microspore development stage of the flower buds was about 6–8 mm long collected 1-2 weeks after flower initiation. At that stage, the microspores were at the uninucleate stage which was suitable for culture. The best callus induction frequency was 90% in the optimized semisolid MS medium fortified with 3.0 mg/L BAP + 3.0 mg/L NAA. PMID:24757416

Mechanism of melphalan crosslink enhancement by misonidazole pretreatment

International Nuclear Information System (INIS)

Taylor, Y.C.; Sawyer, J.M.; Hsu, B.; Brown, J.M.

1984-01-01

Sensitization of Chinese hamster ovary cells to melphalan (L-PAM) toxicity by prior treatment with misonidazole is associated with increased levels of DNA crosslinks believed to be the critical lesion for bifunctional alkylating agent toxicity. Enhanced L-PAM crosslinking of DNA could occur by a variety of mechanisms in MISO-pretreated cells including: (1) increased transport or binding of L-PAM, (2) decreased repair of L-PAM monoadducts which would allow more time for their conversion to crosslinks, (3) decreased crosslink repair (unhooking of one arm), or (4) chemical modification of the DNA structure, presumably by bound MISO derivatives, such that crosslink formation is facilitated. Previous studies have eliminated mechanisms (1) and (3). Mechanism (4) was investigated by following MISO-pretreatments of whole cells with L-PAM treatments of the isolated DNA from these cells. Treatment of bare DNA with L-PAM modeled very well the crosslinking behavior in whole cells although it was somewhat more efficient. In the presence of double stranded DNA and absence of repair systems during and after the L-PAM exposure, it was determined that MISO-pretreatments did not increase the crosslinking efficiency of L-PAM

Microbial Lipid Production from Enzymatic Hydrolysate of Pecan Nutshell Pretreated by Combined Pretreatment.

Science.gov (United States)

Qin, Lizhen; Qian, Hanyu; He, Yucai

2017-12-01

Biodiesel is a fuel composed of monoalkyl esters of long-chain fatty acids derived from renewable biomass sources. In this study, biomass waste pecan nutshell (PS) was attempted to be converted into microbial oil. For effective utilization of PS, sequential pretreatment with ethylene glycol-H 2 SO 4 -water (78:2:20, wt:wt:wt) at 130 °C for 30 min and aqueous ammonia (25 wt%) at 50 °C for 24 h was used to enhance its enzymatic saccharification. Significant linear correlation was obtained about delignification-saccharification (R 2  = 0.9507). SEM and FTIR results indicated that combination pretreatment could effectively remove lignin and xylan in PS for promoting its enzymatic saccharification. After 72 h, the reducing sugars from the hydrolysis of 50 g/L pretreated PS by combination pretreatment could be obtained at 73.6% yield. Using the recovered PS hydrolysates containing 20 g/L glucose as carbon source, microbial lipids produced from the PS hydrolysates by Rhodococcus opacus ACCC41043. Four fatty acids including palmitic acid (C16:0; 23.1%), palmitoleic acid (C16:1; 22.4%), stearic acid (C18:0; 15.3%), and oleic acid (C18:1; 23.9%) were distributed in total fatty acids. In conclusion, this strategy has potential application in the future.

Reassessing the NTCTCS Staging Systems for Differentiated Thyroid Cancer, Including Age at Diagnosis.

Science.gov (United States)

McLeod, Donald S A; Jonklaas, Jacqueline; Brierley, James D; Ain, Kenneth B; Cooper, David S; Fein, Henry G; Haugen, Bryan R; Ladenson, Paul W; Magner, James; Ross, Douglas S; Skarulis, Monica C; Steward, David L; Xing, Mingzhao; Litofsky, Danielle R; Maxon, Harry R; Sherman, Steven I

2015-10-01

Thyroid cancer is unique for having age as a staging variable. Recently, the commonly used age cut-point of 45 years has been questioned. This study assessed alternate staging systems on the outcome of overall survival, and compared these with current National Thyroid Cancer Treatment Cooperative Study (NTCTCS) staging systems for papillary and follicular thyroid cancer. A total of 4721 patients with differentiated thyroid cancer were assessed. Five potential alternate staging systems were generated at age cut-points in five-year increments from 35 to 70 years, and tested for model discrimination (Harrell's C-statistic) and calibration (R(2)). The best five models for papillary and follicular cancer were further tested with bootstrap resampling and significance testing for discrimination. The best five alternate papillary cancer systems had age cut-points of 45-50 years, with the highest scoring model using 50 years. No significant difference in C-statistic was found between the best alternate and current NTCTCS systems (p = 0.200). The best five alternate follicular cancer systems had age cut-points of 50-55 years, with the highest scoring model using 50 years. All five best alternate staging systems performed better compared with the current system (p = 0.003-0.035). There was no significant difference in discrimination between the best alternate system (cut-point age 50 years) and the best system of cut-point age 45 years (p = 0.197). No alternate papillary cancer systems assessed were significantly better than the current system. New alternate staging systems for follicular cancer appear to be better than the current NTCTCS system, although they require external validation.

Reassessing the NTCTCS Staging Systems for Differentiated Thyroid Cancer, Including Age at Diagnosis

Science.gov (United States)

McLeod, Donald S.A.; Jonklaas, Jacqueline; Brierley, James D.; Ain, Kenneth B.; Cooper, David S.; Fein, Henry G.; Haugen, Bryan R.; Ladenson, Paul W.; Magner, James; Ross, Douglas S.; Skarulis, Monica C.; Steward, David L.; Xing, Mingzhao; Litofsky, Danielle R.; Maxon, Harry R.

2015-01-01

Background: Thyroid cancer is unique for having age as a staging variable. Recently, the commonly used age cut-point of 45 years has been questioned. Objective: This study assessed alternate staging systems on the outcome of overall survival, and compared these with current National Thyroid Cancer Treatment Cooperative Study (NTCTCS) staging systems for papillary and follicular thyroid cancer. Methods: A total of 4721 patients with differentiated thyroid cancer were assessed. Five potential alternate staging systems were generated at age cut-points in five-year increments from 35 to 70 years, and tested for model discrimination (Harrell's C-statistic) and calibration (R2). The best five models for papillary and follicular cancer were further tested with bootstrap resampling and significance testing for discrimination. Results: The best five alternate papillary cancer systems had age cut-points of 45–50 years, with the highest scoring model using 50 years. No significant difference in C-statistic was found between the best alternate and current NTCTCS systems (p = 0.200). The best five alternate follicular cancer systems had age cut-points of 50–55 years, with the highest scoring model using 50 years. All five best alternate staging systems performed better compared with the current system (p = 0.003–0.035). There was no significant difference in discrimination between the best alternate system (cut-point age 50 years) and the best system of cut-point age 45 years (p = 0.197). Conclusions: No alternate papillary cancer systems assessed were significantly better than the current system. New alternate staging systems for follicular cancer appear to be better than the current NTCTCS system, although they require external validation. PMID:26203804

Biomass Deconstruction and Pretreatment | Bioenergy | NREL

Science.gov (United States)

Deconstruction and Pretreatment Biomass Deconstruction and Pretreatment Our mission is to transform -cyclohexane hydrocarbons were produced by noble metal and acid zeoloite catalytic upgrading of biomass-derived by mechanical refining process. The left side shows biomass feedstock (represented by brown spheres

Advances in HTGR Wastewater Treatment System Design

International Nuclear Information System (INIS)

Li Junfeng; Qiu Yu; Wang Jianlong; Jia Fei

2014-01-01

The source terms of radioactive wastewater from HTR-PM were introduced. Concentration process should be used to reduce volume. A radioactive wastewater treatment system was designed by using Disc tubular reverse osmosis (DTRO) membrane system. The pretreatment system was simplify by using a cartridge filter. A three-stage membrane system was built. The operated characters to treat low and intermediate radioactive waste water were studied. A concentration rates of 25-50 is reached. The decontamination factor of the membrane system can reach 30-100. (author)

Environmentally friendly hybrid coatings for corrosion protection: silane based pre-treatments and nanostructured waterborne coatings

OpenAIRE

Fedel, Michele

2009-01-01

This thesis considers a nanotechnology approach based on the production of metals pre-treatments and organic coatings (a complete protection system at all) designed from the nanoscale. The final aim is to develop protection systems with improved corrosion protection properties and a low environmental impact. In particular, multifunctional silane hybrid molecules were used to design sol-gel pre-treatments for metals and to modify the inner structure of UV curable waterborne organic coatings...

Tank Focus Area pretreatment activities

International Nuclear Information System (INIS)

McGinnis, C.P.; Welch, T.D.; Manke, K.L.

1997-01-01

Plans call for the high-level wastes to be retrieved from the tanks and immobilized in a stable waste form suitable for long-term isolation. Chemistry and chemical engineering operations are required to retrieve the wastes, to condition the wastes for subsequent steps, and to reduce the costs of the waste management enterprise. Pretreatment includes those processes between retrieval and immobilization, and includes preparation of suitable feed material for immobilization and separations to partition the waste into streams that yield lower life-cycle costs. Some of the technologies being developed by the Tank Focus Area (TFA) to process these wastes are described. These technologies fall roughly into three areas: (1) solid/liquid separation (SLS), (2) sludge pretreatment, and (3) supernate pretreatment

Waste Separations and Pretreatment Workshop report

International Nuclear Information System (INIS)

Cruse, J.M.; Harrington, R.A.; Quadrel, M.J.

1994-01-01

This document provides the minutes from the Waste Separations and Pretreatment Workshop sponsored by the Underground Storage Tank-Integrated Demonstration in Salt Lake City, Utah, February 3--5, 1993. The Efficient Separations and Processing-Integrated Program and the Hanford Site Tank Waste Remediation System were joint participants. This document provides the detailed minutes, including responses to questions asked, an attendance list, reproductions of the workshop presentations, and a revised chart showing technology development activities

PRETREATING THORIUM FOR ELECTROPLATING

Science.gov (United States)

Beach, J.G.; Schaer, G.R.

1959-07-28

A method is presented for pretreating a thorium surface prior to electroplating the surface. The pretreatment steps of the invention comprise cleaning by vapor blasting the surface, anodically pickling in a 5 to 15% by volume aqueous hydrochloric acid bath with a current of 125 to 250 amp/sq ft for 3 to 5 min at room temperature, chemically pickling the surface in a 5 to 15% by volume of aqueous sulfuric acid for 3 to 5 min at room temperature, and rinsing the surface with water.

Influence of ultrasound pretreatment on wood physiochemical structure.

Science.gov (United States)

He, Zhengbin; Wang, Zhenyu; Zhao, Zijian; Yi, Songlin; Mu, Jun; Wang, Xiaoxu

2017-01-01

As an initial step to increase the use of renewable biomass resources, this study was aimed at investigating the effects of ultrasound pretreatment on structural changes of wood. Samples were pretreated by ultrasound with the power of 300W and frequency of 28kHz in aqueous soda solution, aqueous acetic acid, or distilled water, then pretreated and control samples were characterized via X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). The results shown that ultrasound pretreatment is indeed effective in modifying the physiochemical structure of eucalyptus wood; the pretreatment decreased the quantity of alkali metals (e.g., potassium, calcium and magnesium) in the resulting material. Compared to the control group, the residual char content of samples pretreated in aqueous soda solution increased by 10.08%-20.12% and the reaction temperature decreased from 361°C to 341°C, however, in samples pretreated by ultrasound in acetic solution or distilled water, the residual char content decreased by 12.40%-21.45% and there were no significant differences in reactivity apart from a slightly higher maximum reaction rate. Ultrasound pretreatment increased the samples' crystallinity up to 35.5% and successfully removed cellulose, hemicellulose, and lignin from the samples; the pretreatment also increased the exposure of the sample to the treatment solutions, broke down sample pits, and generated collapses and microchannels on sample pits, and removed attachments in the samples. Copyright © 2016 Elsevier B.V. All rights reserved.

A STUDY OF BRACKISH WATER MEMBRANE WITH ULTRAFILTRATION PRETREATMENT IN INDONESIA´S COASTAL AREA

Directory of Open Access Journals (Sweden)

Elis Hastuti

2012-01-01

Full Text Available Water pollution and sea water intrusion to water sources in coastal areas result lack of provision safe drinking water by the drinking water regional company or coastal community. The existing water treatment plant that operated on brackish surface water or groundwater feed requires improving process. Membrane process could be a choice to treat the quality of brackish water to the level of potable water that designed to lower cost with high stabil flux and longer lifetime. This research focus on application of pilot plant of brackish water treatment using Ultrafiltration (UF membrane-air lift system as pretreatment of Reverse Osmosis (RO membrane-low pressure. Brackish water sources contain high colloidal and suspended solids that can cause fouling load of RO membranes and impair its performance. UF pretreatment operation tested by addition of compressed air into the feed (air lift system, resulted stable flux, reduces membrane fouling and low feed pressure. A flux of RO with UF pretreatment can produce drinking water of 30--61 L/m2·hour. It was observed, the good quality of RO permeate resulted by using a pretreatment of UF--PS (Polysulfone-UF with total dissolved solid rejection about 96--98% and color rejection about 99--100% at 5 or 8 bars of operation pressure. This paper concludes that performance of membrane technology with UF--air lift system pretreatment and RO membrane-low pressure could be accepted as condition of brackish water source in Indonesia coastal areas in producing drinking water.

A study of brackish water membrane with ultrafiltration pretreatment in Indonesia’s coastal area

Directory of Open Access Journals (Sweden)

Elis Hastuti

2012-06-01

Full Text Available Water pollution and sea water intrusion to water sources in coastal areas result lack of provision safe drinking water by the drinking water regional company or coastal community. The existing water treatment plant that operated on brackish surface water or groundwater feed requires improving process. Membrane process could be a choice to treat the quality of brackish water to the level of potable water that designed to lower cost with high stabil flux and longer lifetime. This research focus on application of pilot plant of brackish water treatment using Ultrafiltration (UF membrane-air lift system as pretreatment of Reverse Osmosis (RO membrane-low pressure. Brackish water sources contain high colloidal and suspended solids that can cause fouling load of RO membranes and impair its performance. UF pretreatment operation tested by addition of compressed air into the feed (air lift system, resulted stable flux, reduces membrane fouling and low feed pressure. A flux of RO with UF pretreatment can produce drinking water of 30–61 L/m2∙hour. It was observed, the good quality of RO permeate resulted by using a pretreatment of UF–PS (Polysulfone-UF with total dissolved solid rejection about 96–98% and color rejection about 99–100% at 5 or 8 bars of operation pressure. This paper concludes that performance of membrane technology with UF–air lift system pretreatment and RO membrane-low pressure could be accepted as condition of brackish water source in Indonesia coastal areas in producing drinking water.

Comparative study of nasopharyngeal carcinoma staging system between the chinese 2008 and '92 Fuzhou

International Nuclear Information System (INIS)

Zong Jingfeng; Lin Shaojun; Zhang Yu; Chen Yunbin; Guo Qiaojuan; Pan Jianji

2010-01-01

Objective: To carry out a comparative study between the Chinese 2008 and '92 staging system of nasopharyngeal carcinoma (NPC). Methods: A total of 777 patients presented with untreated non disseminated NPC who had received MRI scan of nasopharynx and neck were studied retrospectively. The clinical materials and information of imaging were collected. All patients were restaged according to the Chinese 2008 and 92 staging system of nasopharyngeal carcinoma. Distribution of T, N stage, survival and prognostic value were compared. 513 patients of the 777 cases were treated with conventional radiotherapy, 264 cases with intensity modulated radiation therapy. Results: The 3-year follow-up rate was 97.6%. The consistency of T stages was 95.0%. T, N and clinical stage distributions in two systems were similar ( Kappa = 0.93, P = 0.000; Kappa = 0.58, P = 0.000; Kappa = 0.74, P = 0.000). Local failure-free survival and disease specific survival were also similar. There was no difference of distant metastasis between N 0 and N 1 (χ 2 = 1.94, P=0. 164), and a marginal difference between N 1 and N 2 (χ 2 =3.83, P=0.051) in the Chinese '92 staging system. However, although there was also no difference of distant metastasis-free survival between N 0 and N 1a (χ 2 =0.07, P =0.797), ) the difference of overall survival among N 1b , N 2 , and N 3 were significant (χ 2 = 4.95, P = 0.026; χ 2 = 6.74, P = 0.009) in the Chinese 2008 staging system. Conventional radiotherapy or intensity modulated radiation therapy was not a prognostic factor for survival (χ 2 = 3.60, P =0.058). It is reasonable for the Chinese 2008 staging system integrated lymph node characteristics such as laterality, level and extra nodal neoplastic spread into the N staging criteria (χ 2 = 6.59, P = 0.010; χ 2 =4.78, P=0. 029; χ 2 =9.32, P=0.002). Conclusions: For the Chinese 2008 staging system, it was reasonable to simplify the previous T stage. The N stage showed a better predictive role of distant

Hydrolysis of alkaline pretreated banana peel

Science.gov (United States)

Fatmawati, A.; Gunawan, K. Y.; Hadiwijaya, F. A.

2017-11-01

Banana peel is one of food wastes that are rich in carbohydrate. This shows its potential as fermentation substrate including bio-ethanol. This paper presented banana peel alkaline pretreatment and enzymatic hydrolysis. The pretreatment was intended to prepare banana peel in order to increase hydrolysis performance. The alkaline pretreatment used 10, 20, and 30% w/v NaOH solution and was done at 60, 70 and 80°C for 1 hour. The hydrolysis reaction was conducted using two commercial cellulose enzymes. The reaction time was varied for 3, 5, and 7 days. The best condition for pretreatment process was one conducted using 30% NaOH solution and at 80°C. This condition resulted in cellulose content of 90.27% and acid insoluble lignin content of 2.88%. Seven-day hydrolysis time had exhibited the highest reducing sugar concentration, which was7.2869 g/L.

Dilute acid pretreatment of rye straw and bermudagrass for ethanol production

Energy Technology Data Exchange (ETDEWEB)

Ye Sun; Jay J Cheng [North Carolina State Univ., Dept. of Biological and Agricultural Engineering, Raleigh, NC (United States)

2005-09-01

Ethanol production from lignocellulosic materials provides an alternative energy production system. Rye and bermudagrass that are used in hog farms for nutrient uptake from swine wastewater have the potential for fuel ethanol production because they have a relative high cellulose and hemicellulose content. Dilute sulfuric acid pretreatment of rye straw and bermudagrass before enzymatic hydrolysis of cellulose was investigated in this study. The biomass at a solid loading rate of 10% was pretreated at 121 deg C with different sulfuric acid concentrations (0.6, 0.9, 1.2 and 1.5%, w/w) and residence times (30, 60, and 90 min). Total reducing sugars, arabinose, galactose, glucose, and xylose in the prehydrolyzate were analyzed. In addition, the solid residues were hydrolyzed by cellulases to investigate the enzymatic digestibility. With the increasing acid concentration and residence time, the amount of arabinose and galactose in the filtrates increased. The glucose concentration in the prehydrolyzate of rye straw was not significantly influenced by the sulfuric acid concentration and residence time, but it increased in the prehydrolyzate of bermudagrass with the increase of pretreatment severity. The xylose concentration in the filtrates increased with the increase of sulfuric acid concentration and residence time. Most of the arabinan, galactan and xylan in the biomass were hydrolyzed during the acid pretreatment. Cellulose remaining in the pretreated feedstock was highly digestible by cellulases from Trichoderma reesei. (Author)

Pretreatment of wheat straw for fermentation to methane

International Nuclear Information System (INIS)

Hashimoto, A.G.

1986-01-01

The effects of pretreating wheat straw with gamma-ray irradiation, ammonium hydroxide, and sodium hydroxide on methane yield, fermentation rate constant, and loss of feedstock constituents were evaluated using laboratory-scale batch fermentors. Results showed that methane yield increased as pretreatment alkali concentration increased, with the highest yield being 37% over untreated straw for the pretreatment consisting of sodium hydroxide dosage of 34 g OH - /kg volatile solids, at 90 0 C for 1 h. Gamma-ray irradiation had no significant effect on methane yield. Alkaline pretreatment temperatures above 100 0 C caused a decrease in methane yield. After more than 100 days of fermentation, all of the hemicellulose and more than 80% of the cellulose were degraded. The loss in cellulose and hemicellulose accounted for 100% of the volatile solids lost. No consistent effect of pretreatments on batch fermentation rates was noted. Semicontinuous fermentations of straw-manure mixtures confirmed the relative effectiveness of sodium- and ammonium-hydroxide pretreatments

Pretreatment with polyamines alleviate the deleterious effects of diuron in maize leaves.

Science.gov (United States)

Durmuş, Nuran; Bekircan, Tuba

2015-03-01

h of diuron treatment. Also, the decrease in CAT activity induced by diuron at 72 h was completely prevented by PUT. It can be concluded that pretreatment of maize leaves with polyamines reduced the damage produced by diuron and the protective effects of polyamines against diuron toxicity were closely associated with antioxidant system.

Ensiling of wheat straw decreases the required temperature in hydrothermal pretreatment

DEFF Research Database (Denmark)

Ambye-Jensen, Morten; Thomsen, Sune Tjalfe; Kádár, Zsófia

2013-01-01

BACKGROUND: Ensiling is a well-known method for preserving green biomasses through anaerobic production of organic acids by lactic acid bacteria. In this study, wheat straw is subjected to ensiling in combination with hydrothermal treatment as a combined pretreatment method, taking advantage...... of the produced organic acids. RESULTS: Ensiling for 4 weeks was accomplished in a vacuum bag system after addition of an inoculum of Lactobacillus buchneri and 7% w/w xylose to wheat straw biomass at 35% final dry matter. Both glucan and xylan were preserved, and the DM loss after ensiling was less than 0...... increased.Subsequent enzymatic hydrolysis of the solid fractions showed that ensiling significantly improved the effect of pretreatment, especially at the lower temperatures of 170 and 180°C.The overall glucose yields after pretreatments of ensiled wheat straw were higher than for non-ensiled wheat straw...

Pretreatment method for radioactive iodine-containing liquid wastes and pretreatment device

International Nuclear Information System (INIS)

Wakaida, Yasuo.

1996-01-01

Heretofore, radioactive iodine-containing liquid wastes have been discharged directly to a storing and decaying storage vessel to conduct a water draining treatment. In the present invention, the radioactive iodine-containing liquid wastes to be discharged are not discharged to the storage vessel directly but injected to a filling tank, as a pretreatment, to distinguish whether proteins are mixed in the liquid wastes or not. When proteins are mixed, miscellaneous materials such as proteins are recovered and removed by a protein processing system. When proteins are not mixed, radioactive iodine is recovered and removed directly by an iodine processing system. With such procedures, water draining treatment in the storing and decaying storage vessel is mitigated, and even when the amount of the radioactive iodine-containing liquid wastes is increased, the existent maintaining and decaying storage vessel can be used as it is. Accordingly, a safe water draining treatment with good efficiency can be conducted relative to radioactive iodine-containing liquid wastes at a reduced cost. (T.M.)

Configuration of management accounting information system for multi-stage manufacturing

Science.gov (United States)

Mkrtychev, S. V.; Ochepovsky, A. V.; Enik, O. A.

2018-05-01

The article presents an approach to configuration of a management accounting information system (MAIS) that provides automated calculations and the registration of normative production losses in multi-stage manufacturing. The use of MAIS with the proposed configuration at the enterprises of textile and woodworking industries made it possible to increase the accuracy of calculations for normative production losses and to organize accounting thereof with the reference to individual stages of the technological process. Thus, high efficiency of multi-stage manufacturing control is achieved.

Pretreatment Engineering Platform Phase 1 Final Test Report

Energy Technology Data Exchange (ETDEWEB)

Kurath, Dean E.; Hanson, Brady D.; Minette, Michael J.; Baldwin, David L.; Rapko, Brian M.; Mahoney, Lenna A.; Schonewill, Philip P.; Daniel, Richard C.; Eslinger, Paul W.; Huckaby, James L.; Billing, Justin M.; Sundar, Parameshwaran S.; Josephson, Gary B.; Toth, James J.; Yokuda, Satoru T.; Baer, Ellen BK; Barnes, Steven M.; Golovich, Elizabeth C.; Rassat, Scot D.; Brown, Christopher F.; Geeting, John GH; Sevigny, Gary J.; Casella, Amanda J.; Bontha, Jagannadha R.; Aaberg, Rosanne L.; Aker, Pamela M.; Guzman-Leong, Consuelo E.; Kimura, Marcia L.; Sundaram, S. K.; Pires, Richard P.; Wells, Beric E.; Bredt, Ofelia P.

2009-12-23

Pacific Northwest National Laboratory (PNNL) was tasked by Bechtel National Inc. (BNI) on the River Protection Project, Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to conduct testing to demonstrate the performance of the WTP Pretreatment Facility (PTF) leaching and ultrafiltration processes at an engineering-scale. In addition to the demonstration, the testing was to address specific technical issues identified in Issue Response Plan for Implementation of External Flowsheet Review Team (EFRT) Recommendations - M12, Undemonstrated Leaching Processes.( ) Testing was conducted in a 1/4.5-scale mock-up of the PTF ultrafiltration system, the Pretreatment Engineering Platform (PEP). Parallel laboratory testing was conducted in various PNNL laboratories to allow direct comparison of process performance at an engineering-scale and a laboratory-scale. This report presents and discusses the results of those tests.

Pretreatment Engineering Platform Phase 1 Final Test Report

International Nuclear Information System (INIS)

Kurath, Dean E.; Hanson, Brady D.; Minette, Michael J.; Baldwin, David L.; Rapko, Brian M.; Mahoney, Lenna A.; Schonewill, Philip P.; Daniel, Richard C.; Eslinger, Paul W.; Huckaby, James L.; Billing, Justin M.; Sundar, Parameshwaran S.; Josephson, Gary B.; Toth, James J.; Yokuda, Satoru T.; Baer, Ellen B.K.; Barnes, Steven M.; Golovich, Elizabeth C.; Rassat, Scot D.; Brown, Christopher F.; Geeting, John G.H.; Sevigny, Gary J.; Casella, Amanda J.; Bontha, Jagannadha R.; Aaberg, Rosanne L.; Aker, Pamela M.; Guzman-Leong, Consuelo E.; Kimura, Marcia L.; Sundaram, S.K.; Pires, Richard P.; Wells, Beric E.; Bredt, Ofelia P.

2009-01-01

Pacific Northwest National Laboratory (PNNL) was tasked by Bechtel National Inc. (BNI) on the River Protection Project, Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to conduct testing to demonstrate the performance of the WTP Pretreatment Facility (PTF) leaching and ultrafiltration processes at an engineering-scale. In addition to the demonstration, the testing was to address specific technical issues identified in Issue Response Plan for Implementation of External Flowsheet Review Team (EFRT) Recommendations - M12, Undemonstrated Leaching Processes. Testing was conducted in a 1/4.5-scale mock-up of the PTF ultrafiltration system, the Pretreatment Engineering Platform (PEP). Parallel laboratory testing was conducted in various PNNL laboratories to allow direct comparison of process performance at an engineering-scale and a laboratory-scale. This report presents and discusses the results of those tests.

Two-stage model of development of heterogeneous uranium-lead systems in zircon

International Nuclear Information System (INIS)

Mel'nikov, N.N.; Zevchenkov, O.A.

1985-01-01

Behaviour of isotope systems of multiphase zircons at their two-stage distortion is considered. The results of calculations testify to the fact that linear correlations on the diagram with concordance can be explained including two-stage discovery of U-Pb systems of cogenetic zircons if zircon is considered physically heterogeneous and losing in its different part different ratios of accumulated radiogenic lead. ''Metamorphism ages'' obtained by these two-stage opening zircons are intermediate, and they not have geochronological significance while ''crystallization ages'' remain rather close to real ones. Two-stage opening zircons in some cases can be diagnosed by discordance of their crystal component

Examination of Spray-Applied Oxsilan 9810/2 Steel Pretreatment on a Mine Resistant Ambush Protected (MRAP) Vehicle

Science.gov (United States)

2013-10-01

Coating (CARC) system. The product demonstrated here is Oxsilan 9810/2, manufactured by Chemetall Inc., which satisfies the hexavalent chrome ...system. The product demonstrated here is Oxsilan 9810/2, manufactured by Chemetall Inc., and satisfies the hexavalent chrome prohibition while...2 Omitting this pretreatment/conversion coating step was justified because hexavalent chromium- based pretreatments, such as DOD-P-15328 (8

[Retrospective analysis of 47 cases with hilar cholangiocarcinoma using T-staging system].

Science.gov (United States)

Peng, Cheng-hong; Zhao, Zhi-ming; Peng, Shu-you; Liu, Ying-bin; Wu, Yü-lian; Fang, He-qing; Jiang, Xian-chuan

2005-01-01

To evaluate the clinical value of T-staging system for hilar cholangiocarcinoma which was adopted in memorial Sloan-Kettering cancer center of New York. The image data of these 47 patients were analyzed retrospectively from December 1997 to December 2002 whose data were according with our demand, and they were staged into three-stage according to the criteria of the T-staging system. The difference of respectability, ratio of tumor-free resection margin and actuarial survival rate were analyzed for different T-staging. And the coincident ratio of three different kinds of imaging methods was also analyzed. Twenty patients had T(1) tumors, twenty three had T(2) tumors and four had T(3) tumors. The resectability of the three stage was 60%, 39% and 0% respectively, and the difference was significant (P = 0.013). The likelihood of achieving tumor-free margin decreased progressively with increasing T stage (P = 0.018). The cumulative 1-year survival rates of T(1), T(2) and T(3) patients were 60%, 39% and 0% respectively, and the cumulative 3-year survival rate was 35%, 9% and 0% respectively, the survival of different stage patients differed markedly (P = 0.0103). The coincident ratio of combined using MRCP and color Doppler-ultrasonography was higher than that of combined using MRCP and B-ultrasonography or combined using CT/SCT and color Doppler-ultrasonography (P = 0.007). The T-staging system has a better value for preoperative assessment, and can be used to judge resectability and survival of hilar cholangiocarcinoma. It will be helpful to use MRCP and color Doppler-Ultrasonography combined to verdict the coverage of the tumor and the T-staging preoperatively.

Urine Pretreatment History and Perspective in NASA Human Spaceflight

Science.gov (United States)

Anderson, Molly; Adam, Niklas; Chambers, Antja; Broyan, James

2015-01-01

Urine pretreatment is a technology that may seem to have small mass impacts in future spaceflight missions, but can have significant impacts on reliability, life, and performance of the rest of the wastewater management and recovery systems. NASA has experience with several different urine pretreatment systems, including those flow on the space shuttle, evaluated for NASA waste collection systems or used in Russian commodes on ISS, or developed by NASA or industry as alternatives. Each has had unique requirements for shelf life, operational life, and the life or conditions of the stored, treated urine. Each was evaluated under different test conditions depending on mission, and depending on testing experience developed over NASA's history. Those that were flown led to further lessons learned about hardware compatibility and control. As NASA looks forward to human spaceflight missions beyond low Earth orbit, these techniques need to be evaluated in new light. Based on published design reference missions, candidate requirements can be derived for future systems. Initial comparisons between these requirements and previous performance or test results can be performed. In many cases these comparisons reveal data gaps. Successful previous performance is not enough to address current needs.

Pretreatment organ function in patients with advanced head and neck cancer: clinical outcome measures and patients' views

Directory of Open Access Journals (Sweden)

Rasch Coen RN

2009-11-01

Full Text Available Abstract Background Aim of this study is to thoroughly assess pretreatment organ function in advanced head and neck cancer through various clinical outcome measures and patients' views. Methods A comprehensive, multidimensional assessment was used, that included quality of life, swallowing, mouth opening, and weight changes. Fifty-five patients with stage III-IV disease were entered in this study prior to organ preserving (chemoradiation treatment. Results All patients showed pretreatment abnormalities or problems, identified by one or more of the outcome measures. Most frequent problems concerned swallowing, pain, and weight loss. Interestingly, clinical outcome measures and patients' perception did no always concur. E.g. videofluoroscopy identified aspiration and laryngeal penetration in 18% of the patients, whereas only 7 patients (13% perceived this as problematic; only 2 out of 7 patients with objective trismus actually perceived trismus. Conclusion The assessment identified several problems already pre-treatment, in this patient population. A thorough assessment of both clinical measures and patients' views appears to be necessary to gain insight in all (perceived pre-existing functional and quality of life problems.

Techno-economic analysis of organosolv pretreatment process from lignocellulosic biomass

DEFF Research Database (Denmark)

Rodrigues Gurgel da Silva, Andrè; Errico, Massimiliano; Rong, Ben-Guang

2018-01-01

data, we propose a feasible process flowsheet for organosolv pretreatment. Simulation of the pretreatment process provided mass and energy balances for a techno-economic analysis, and the values were compared with the most prevalent and mature pretreatment method: diluted acid. Organosolv pretreatment...... required more energy, 578.1 versus 213.8 MW for diluted acid pretreatment, but resulted in a higher ethanol concentration after the biomass fermentation, 11.1% compared to 5.4%. Total annual costs (TACs) calculations showed advantages for diluted acid pretreatment, but future improvements explored...

Chemical Pretreatment Methods for the Production of Cellulosic Ethanol: Technologies and Innovations

Directory of Open Access Journals (Sweden)

Edem Cudjoe Bensah

2013-01-01

Full Text Available Pretreatment of lignocellulose has received considerable research globally due to its influence on the technical, economic and environmental sustainability of cellulosic ethanol production. Some of the most promising pretreatment methods require the application of chemicals such as acids, alkali, salts, oxidants, and solvents. Thus, advances in research have enabled the development and integration of chemical-based pretreatment into proprietary ethanol production technologies in several pilot and demonstration plants globally, with potential to scale-up to commercial levels. This paper reviews known and emerging chemical pretreatment methods, highlighting recent findings and process innovations developed to offset inherent challenges via a range of interventions, notably, the combination of chemical pretreatment with other methods to improve carbohydrate preservation, reduce formation of degradation products, achieve high sugar yields at mild reaction conditions, reduce solvent loads and enzyme dose, reduce waste generation, and improve recovery of biomass components in pure forms. The use of chemicals such as ionic liquids, NMMO, and sulphite are promising once challenges in solvent recovery are overcome. For developing countries, alkali-based methods are relatively easy to deploy in decentralized, low-tech systems owing to advantages such as the requirement of simple reactors and the ease of operation.

Changes of endocrine and ultrasound markers as ovarian aging in modifying the Stages of Reproductive Aging Workshop (STRAW) staging system with subclassification of mid reproductive age stage.

Science.gov (United States)

Ding, Ting; Luo, Aiyue; Jiang, Jingjing; Du, Xiaofang; Yang, Shuhong; Lai, Zhiwen; Shen, Wei; Lu, Yunping; Ma, Ding; Wang, Shixuan

2013-01-01

To demonstrate the changes of ovarian aging markers across the Stages of Reproductive Aging Workshop (STRAW) stages and modify it with subclassification of mid reproductive age stage (MR). Healthy females were classified according to the STRAW system. Serum basal FSH, LH, E2, and anti-Müllerian hormone (AMH) were detected, FSH/LH ratio calculated, and antral follicle counts (AFCs) determined in follicular phase. Progression through the whole STRAW stages under MR stage subdivided is associated with elevations in FSH, LH, FSH/LH ratio and decreases in E2, AMH and AFCs (p age in MR stage. 0.982 ng/ml AMH and 3 antral follicles (low level of MR 25-30 years) were set as cutoffs to distinguish MR stage into early mid reproductive age (EMR) and late mid reproductive age (LMR) stages. The women in EMR stage compared with LMR could retrieve more oocytes in IVF treatment (p stage, demonstrating disparate reproductive aging period with reduced ovarian reserve in young age across the STRAW stages.

Diagnostic accuracy of pre-treatment biopsy for grading cutaneous mast cell tumours in dogs.

Science.gov (United States)

Shaw, T; Kudnig, S T; Firestone, S M

2018-06-01

Mast cell tumours (MCTs) are common tumours of the canine skin, and are estimated to represent up to 20% of all skin tumours in dogs. Tumour grade has a major impact on the incidence of local recurrence and metastatic potential. In addition to helping the clinician with surgical planning, knowledge of the tumour grade also assists in proper prognostication and client education. For pre-treatment biopsies to be useful, there must exist a high level of correlation between the histopathological grade obtained from the pre-treatment biopsy and the actual histopathological grade from the excisional biopsy. The aim of this study was to determine concordance of tumour grade between various biopsy techniques (wedge, punch, needle core) and the "gold standard" excisional biopsy method. We found an overall concordance rate of 96% based on the Patnaik grading system, and an overall concordance rate of 92% based on the Kiupel grading system. The accuracy of the various biopsy techniques (wedge, punch and needle core) when compared with excisional biopsy was 92%, 100% and 100%, respectively, based on the Patnaik grading system, and 90%, 95% and 100%, respectively, based on the Kiupel grading system. Of the cases with discordant results, the pre-treatment biopsies tended to underestimate the grade of the tumour. Based on these results, we conclude that pre-treatment biopsies are sufficiently accurate for differentiating low-grade from high-grade MCTs, regardless of biopsy technique or tumour location. © 2017 John Wiley & Sons Ltd.

Effects of pre-treatment technologies on quantity and quality of source-sorted municipal organic waste for biogas recovery

DEFF Research Database (Denmark)

Hansen, Trine Lund; Jansen, J.l.C.; Davidsson, Å.

2007-01-01

, collection bag material (plastic or paper) and easily degradable organic matter. Furthermore, the particle size of the biomass was related to the pre-treatment technology. The content of plastic in the biomass depended both on the actual collection bag material used in the system and the pre......Source-sorted municipal organic waste collected from different dwelling types in five Danish cities and pre-treated at three different plants was sampled and characterized several times during one year to investigate the origin of any differences in composition of the pre-treated waste introduced...... by city, pre-treatment technology, dwelling type or annual season. The investigated pre-treatment technologies were screw press, disc screen and shredder + magnet. The average quantity of pre-treated organic waste (biomass) produced from the incoming waste varied between the investigated pre...

Comparison of four staging systems of lymph node metastasis in gastric cancer.

Science.gov (United States)

Zhang, Ming; Zhu, Guanyu; Ma, Yan; Xue, Yingwei

2009-11-01

The classification of lymph node metastasis in patients with gastric cancer is still controversial. Our aim was to evaluate the relative merits of four staging systems of lymph node metastasis. In our study, the nodal status was classified according to the 5th edition of the tumor node metastasis (TNM) system, the Japanese Classification of Gastric Carcinoma (JCGC), the ratio of metastatic lymph nodes, and the size of the largest metastatic lymph node. Each staging system was scored as good (+2), fair (+1), or poor (0) with respect to the theoretical value (extent of the anatomical lymphatic tumor spread), convenience (simplicity), surgical applicability (extent of lymph node dissection), and prognostic value (ability to predict survival rate). In the multivariate analysis including the four staging systems and other potential prognostic factors, stepwise Cox regression revealed that the ratio of metastatic lymph nodes was the most independent prognostic factor. The TNM, ratio, and size systems were convenient because they had no consideration for the location of the tumor and lymph node. Although the JCGC system had advantages in theoretical value and surgical application, it was most optional due to the complexity of the system. Although all different staging systems are comparable, the metastatic lymph node ratio system is convenient, reproducible, and has the highest ability to predict survival.

Biologically Pre-Treated Habitation Waste Water as a Sustainable Green Urine Pre-Treat Solution

Science.gov (United States)

Jackson, W. Andrew; Thompson, Bret; Sevanthi, Ritesh; Morse, Audra; Meyer, Caitlin; Callahan, Michael

2017-01-01

The ability to recover water from urine and flush water is a critical process to allow long term sustainable human habitation in space or bases on the moon or mars. Organic N present as urea or similar compounds can hydrolyze producing free ammonia. This reaction results in an increase in the pH converting ammonium to ammonia which is volatile and not removed by distillation. The increase in pH will also cause precipitation reactions to occur. In order to prevent this, urine on ISS is combined with a pretreat solution. While use of a pretreatment solution has been successful, there are numerous draw backs including: storage and use of highly hazardous solutions, limitations on water recovery (less than 85%), and production of brine with pore dewatering characteristics. We evaluated the use of biologically treated habitation wastewaters (ISS and early planetary base) to replace the current pretreat solution. We evaluated both amended and un-amended bioreactor effluent. For the amended effluent, we evaluated "green" pretreat chemicals including citric acid and citric acid amended with benzoic acid. We used a mock urine/air separator modeled after the urine collection assembly on ISS. The urine/air separator was challenged continually for >6 months. Depending on the test point, the separator was challenged daily with donated urine and flushed with amended or un-amended reactor effluent. We monitored the pH of the urine, flush solution and residual pH in the urine/air separator after each urine event. We also evaluated solids production and biological growth. Our results support the use of both un-amended and amended bioreactor effluent to maintain the operability of the urine /air separator. The ability to use bioreactor effluent could decrease consumable cost, reduce hazards associated with current pre-treat chemicals, allow other membrane based desalination processes to be utilized, and improve brine characteristics.

Pretreatment of Oil Palm Frond (OPF) with Ionic Liquid

Science.gov (United States)

Azmi, I. S.; Azizan, A.; Salleh, R. Mohd

2018-05-01

Pretreatment is the key to unlock the recalcitrance of lignocellulose for cellulosic biofuel production. Increasing attention has been drawn to ionic liquids (ILs) for pretreatment of lignocellulosic biomass because this approach was considered as a green engineering method over other conventional methods. In this work, Oil palm frond (OPF) was pretreated by using the ionic liquid 1-ethyl-3-methylimidazolium acetate [EMIM] Ac at the temperature of 99˚C for 3 hours. The characterization of the untreated and pretreated OPF was conducted by using different techniques which are Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The pretreatment of OPF with [EMIM] Ac was demonstrated to be effective evidenced by the significant reduction of Lateral Order Index (LOI) from FTIR, reduction of Crystallinity Index (CI) based on XRD and the significant morphology changes indicated by SEM. The CI value for the pretreated OPF decreased from 0.47 (untreated sample) to 0.28 while the LOI value decreased from 1.10 to 0.24 after pretreatment with [EMIM]Ac and the SEM morphology showed that the pretreated OPF becomes distorted and disordered.

Condition-specific Quality of Life Assessment at Each Stage of Class III Surgical Orthodontic Treatment -A Prospective Study.

Science.gov (United States)

Tachiki, Chie; Nishii, Yasushi; Takaki, Takashi; Sueishi, Kenji

2018-01-01

Surgical orthodontic treatment has been reported to improve oral health-related quality of life (OHRQL). Such treatment comprises three stages: pre-surgical orthodontic treatment; orthognathic surgery; and post-surgical orthodontic treatment. Most studies have focused on change in OHRQL between before and after surgery. However, it is also necessary to evaluate OHRQL at the pre-surgical orthodontic treatment stage, as it may be negatively affected by dental decompensation compared with at pre-treatment. The purpose of this prospective study was to investigate the influence of surgical orthodontic treatment on QOL by assessing change in condition-specific QOL at each stage of treatment in skeletal class III cases. Twenty skeletal class III patients requiring surgical orthodontic treatment were enrolled in the study. Each patient completed the Orthognathic Quality of Life Questionnaire (OQLQ), which was developed for patients with dentofacial deformity. Its items are grouped into 4 domains: "social aspects of dentofacial deformity"; "facial esthetics"; "oral function"; and "awareness of dentofacial esthetics". The questionnaire was completed at the pre-treatment, pre-surgical orthodontic treatment, and post-surgical orthodontic treatment stages. The results revealed a significant worsening in scores between at pre-treatment and pre-surgical orthodontic treatment in the domains of facial esthetics and oral function (ppre-surgical orthodontic and post-surgical orthodontic treatment in all domains except awareness of dentofacial esthetics (ppre-surgical orthodontic treatment stage. Significant correlations were also observed between improvement in upper and lower lip difference, soft tissue pogonion protrusion, and ANB angle and improvement in OQLQ scores at the post-surgical orthodontic treatment stage. These results indicate that morphologic change influences OHRQL in patients undergoing surgical orthodontic treatment not only after surgery, but also during pre

Methods of pretreating comminuted cellulosic material with carbonate-containing solutions

Energy Technology Data Exchange (ETDEWEB)

Francis, Raymond

2012-11-06

Methods of pretreating comminuted cellulosic material with an acidic solution and then a carbonate-containing solution to produce a pretreated cellulosic material are provided. The pretreated material may then be further treated in a pulping process, for example, a soda-anthraquinone pulping process, to produce a cellulose pulp. The pretreatment solutions may be extracted from the pretreated cellulose material and selectively re-used, for example, with acid or alkali addition, for the pretreatment solutions. The resulting cellulose pulp is characterized by having reduced lignin content and increased yield compared to prior art treatment processes.

Bioethanol production from microwave-assisted acid or alkali-pretreated agricultural residues of cassava using separate hydrolysis and fermentation (SHF).

Science.gov (United States)

Pooja, N S; Sajeev, M S; Jeeva, M L; Padmaja, G

2018-01-01

The effect of microwave (MW)-assisted acid or alkali pretreatment (300 W, 7 min) followed by saccharification with a triple enzyme cocktail (Cellic, Optimash BG and Stargen) with or without detoxification mix on ethanol production from three cassava residues (stems, leaves and peels) by Saccharomyces cerevisiae was investigated. Significantly higher fermentable sugar yields (54.58, 47.39 and 64.06 g/L from stems, leaves and peels, respectively) were obtained after 120 h saccharification from MW-assisted alkali-pretreated systems supplemented (D+) with detoxification chemicals (Tween 20 + polyethylene glycol 4000 + sodium borohydride) compared to the non-supplemented (D0) or MW-assisted acid-pretreated systems. The percentage utilization of reducing sugars during fermentation (48 h) was also the highest (91.02, 87.16 and 89.71%, respectively, for stems, leaves and peels) for the MW-assisted alkali-pretreated (D+) systems. HPLC sugar profile indicated that glucose was the predominant monosaccharide in the hydrolysates from this system. Highest ethanol yields ( Y E , g/g), fermentation efficiency (%) and volumetric ethanol productivity (g/L/h) of 0.401, 78.49 and 0.449 (stems), 0.397, 77.71 and 0.341 (leaves) and 0.433, 84.65 and 0.518 (peels) were also obtained for this system. The highest ethanol yields (ml/kg dry biomass) of ca. 263, 200 and 303, respectively, for stems, leaves and peels from the MW-assisted alkali pretreatment (D+) indicated that this was the most effective pretreatment for cassava residues.

Prediction of Pathological Stage in Patients with Prostate Cancer: A Neuro-Fuzzy Model.

Directory of Open Access Journals (Sweden)

Georgina Cosma

Full Text Available The prediction of cancer staging in prostate cancer is a process for estimating the likelihood that the cancer has spread before treatment is given to the patient. Although important for determining the most suitable treatment and optimal management strategy for patients, staging continues to present significant challenges to clinicians. Clinical test results such as the pre-treatment Prostate-Specific Antigen (PSA level, the biopsy most common tumor pattern (Primary Gleason pattern and the second most common tumor pattern (Secondary Gleason pattern in tissue biopsies, and the clinical T stage can be used by clinicians to predict the pathological stage of cancer. However, not every patient will return abnormal results in all tests. This significantly influences the capacity to effectively predict the stage of prostate cancer. Herein we have developed a neuro-fuzzy computational intelligence model for classifying and predicting the likelihood of a patient having Organ-Confined Disease (OCD or Extra-Prostatic Disease (ED using a prostate cancer patient dataset obtained from The Cancer Genome Atlas (TCGA Research Network. The system input consisted of the following variables: Primary and Secondary Gleason biopsy patterns, PSA levels, age at diagnosis, and clinical T stage. The performance of the neuro-fuzzy system was compared to other computational intelligence based approaches, namely the Artificial Neural Network, Fuzzy C-Means, Support Vector Machine, the Naive Bayes classifiers, and also the AJCC pTNM Staging Nomogram which is commonly used by clinicians. A comparison of the optimal Receiver Operating Characteristic (ROC points that were identified using these approaches, revealed that the neuro-fuzzy system, at its optimal point, returns the largest Area Under the ROC Curve (AUC, with a low number of false positives (FPR = 0.274, TPR = 0.789, AUC = 0.812. The proposed approach is also an improvement over the AJCC pTNM Staging Nomogram (FPR

Assessment of skeletal maturation using mandibular second molar maturation stages.

Science.gov (United States)

Goyal, S; Goyal, S; Gugnani, N

2014-01-01

To investigate the relationship between cervical vertebrae maturation and mandibular second molar calcification stages. The study was designed as a retrospective, descriptive and crosssectional research project. Pre-treatment lateral cephalograms and panoramic radiographs of 99 males and 110 females in the age range of 7 to 18 years 7 months were evaluated with Demirjian Index (DI) and cervical vertebrae maturation indicators (CVMI) of Hassel and Farman. A null hypothesis was proposed that there is no relation between CVMI and DI. A highly significant association (Pearson's contingency coefficient 0.713 for males and 0.863 for females) was found between DI and CVMI. In males, the DI stage E corresponded to stage 2 of CVMI (pre-peak of pubertal growth spurt) and DI stages F and G corresponded to stages 3 and 4 of CVMI (peak of pubertal growth spurt). DI stage H was associated with stages 5 and 6 of CVMI (end of pubertal growth spurt). In females, the DI stages C, D corresponded to CVMI stages 1, 2; DI stages E, F with CVMI stages 3, 4; DI stages G, H with CVMI stages 5, 6. Mandibular second molar calcification stages can be used as indicators for assessment of skeletal maturity.

Chemical pretreatment of lignocellulosic agroindustrial waste for methane production.

Science.gov (United States)

Pellera, Frantseska-Maria; Gidarakos, Evangelos

2018-01-01

This study investigates the effect of different chemical pretreatments on the solubilization and the degradability of different solid agroindustrial waste, namely winery waste, cotton gin waste, olive pomace and juice industry waste. Eight different reagents were investigated, i.e. sodium hydroxide (NaOH), sodium bicarbonate (NaHCO 3 ), sodium chloride (NaCl), citric acid (H 3 Cit), acetic acid (AcOH), hydrogen peroxide (H 2 O 2 ), acetone (Me 2 CO) and ethanol (EtOH), under three condition sets resulting in treatments of varying intensity, depending on process duration, reagent dosage and temperature. Results indicated that chemical pretreatment under more severe conditions is more effective on the solubilization of lignocellulosic substrates, such as those of the present study and among the investigated reagents, H 3 Cit, H 2 O 2 and EtOH appeared to be the most effective to this regard. At the same time, although chemical pretreatment in general did not improve the methane potential of the substrates, moderate to high severity conditions were found to generally be the most satisfactory in terms of methane production from pretreated materials. In fact, moderate severity treatments using EtOH for winery waste, H 3 Cit for olive pomace and H 2 O 2 for juice industry waste and a high severity treatment with EtOH for cotton gin waste, resulted in maximum specific methane yield values. Ultimately, the impact of pretreatment parameters on the different substrates seems to be dependent on their characteristics, in combination with the specific mode of action of each reagent. The overall energy balance of such a system could probably be improved by using lower operating powers and higher solid to liquid ratios. Copyright © 2017 Elsevier Ltd. All rights reserved.

Prognostic value of the pretreatment neutrophil-to-lymphocyte ratio in cervical cancer: a meta-analysis and systematic review.

Science.gov (United States)

Wu, Jiayuan; Chen, Manyu; Liang, Caixia; Su, Wenmei

2017-02-21

The prognostic value of pretreatment neutrophil-to-lymphocyte ratio (NLR) in cervical cancer remains controversial. We conducted a meta-analysis based on the data from 13 studies with 3729 patients to evaluate the association between the pretreatment NLR and the clinical outcomes of overall survival and progression-free survival in patients with cervical cancer. The relationship between NLR and clinicopathological parameters was also assessed. Hazard ratio (HR) or odds ratio (OR) with its 95% confidence interval (CI) was used as the effect size estimate. Our analysis indicated that elevated pretreatment NLR was a poor prognostic marker for patients with cervical cancer because it predicted unfavorable overall survival (HR = 1.375, 95% CI: 1.200-1.576) and progression-free survival (HR = 1.646, 95% CI: 1.313-2.065). Increased NLR is also significantly associated with the larger tumor size (OR = 1.780, 95% CI: 1.090-2.908), advanced clinical stage (OR = 2.443, 95% CI: 1.730-3.451), and positive lymph node metastasis (OR = 2.380, 95% CI: 1.775-3.190). By these results, high pretreatment NLR predicted a shorter survival period for patients with cervical cancer, and it could be served as a novel index of prognostic evaluation in patients with cervical cancer.

Prognostic value of pretreatment volume-based quantitative 18F-FDG PET/CT parameters in patients with malignant pleural mesothelioma

International Nuclear Information System (INIS)

Kitajima, Kazuhiro; Doi, Hiroshi; Kuribayashi, Kozo; Hashimoto, Masaki; Tsuchitani, Tatsuya; Tanooka, Masao; Fukushima, Kazuhito; Nakano, Takashi; Hasegawa, Seiki; Hirota, Shozo

2017-01-01

Purpose: To investigate the relationships between pretreatment volume-based quantitative 18 F-fluorodeoxyglucose (FDG) positron emission tomography/computed tomography (PET/CT) parameters and overall survival (OS) in patients with malignant pleural mesothelioma (MPM). Materials and methods: We retrospectively reviewed data from 201 MPM patients, of whom 38 underwent surgical resection, and calculated the maximum standardized uptake value (SUVmax), metabolic tumor volume (MTV), and total lesion glycolysis (TLG), including primary tumors and nodal or distant metastatic lesions, on pretreatment 18 F-FDG PET/CT. Relationships between clinicopathological factors (age, sex, performance status, European Organization for Research and Treatment of Cancer [EORTC] score, histological subtype, TNM stage, and treatment strategy), volume-based quantitative PET/CT parameters, and OS were evaluated using a Cox proportional hazards model and log-rank test. Results: The median follow-up was 15 months (range, 1–96 months; median, 17 months). In a univariate analysis of all patients, older age (p < 0.05), high EORTC score (p < 0.001), non-epithelioid histological subtype (p < 0.001), high T stage (p < 0.001), positive N/M status (p < 0.05, p < 0.001), advanced TNM stage (p < 0.001), non-surgical treatment (p < 0.001), and high SUVmax (p < 0.001), MTV (p < 0.001), or TLG (p < 0.001) were associated with significantly shorter OS. A multivariate analysis confirmed non-epithelioid subtype (hazard ratio [HR]: 1.69, 95% confidence interval [CI]: 1.14–2.48; p < 0.05), non-surgical treatment (HR: 0.58, 95% CI: 0.34–0.95; p < 0.05), and high TLG (HR: 1.97, 95% CI: 1.14–3.44; p < 0.05) as independent negative predictors. Conclusions: Pretreatment volume-based quantitative 18 F-FDG PET/CT parameters, especially TLG, could serve as potential surrogate markers for MPM prognosis.

Stages in the energetics of baroclinic systems

Science.gov (United States)

Orlanski, Isidoro; Sheldon, John P.

1995-10-01

The results from several idealized and case studies are drawn together to form a comprehensive picture of "downstream baroclinic evolution" using local energetics. This new viewpoint offers a complementary alternative to the more conventional descriptions of cyclone development. These additional insights are made possible largely because the local energetics approach permits one to define an energy flux vector which accurately describes the direction of energy dispersion and quantifies the role of neighboring systems in local development. In this view, the development of a system's energetics is divided into three stages. In Stage 1, a pre-existing disturbance well upstream of an incipient trough loses energy via ageostrophic geopotential fluxes directed downstream through the intervening ridge, generating a new energy center there. In Stage 2, this new energy center grows vigorously, at first due to the convergence of these fluxes, and later by baroclinic conversion as well. As the center matures, it begins to export energy via geopotential fluxes to the eastern side of the trough, initiating yet another energy center. In Stage 3, this new energy center continues to grow while that on the western side of the trough decays due to a dwinding supply of energy via fluxes from the older upstream system and also as a consequence of its own export of energy downstream. As the eastern energy center matures, it exports energy further downstream, and the sequence begins anew. The USA "Blizzard of'93" is used as a new case study to test the limits to which this conceptual sequence might apply, as well as to augment the current limited set of case studies. It is shown that, despite the extraordinary magnitude of the event, the evolution of the trough associated with the Blizzard fits the conceptual picture of downstream baroclinic evolution quite well, with geopotential fluxes playing a critical rôle in three respects. First, fluxes from an old, decaying system in the

The effect of pretreatment on the performance of membrane separation processes in the circulation water systems of paper production; Esikaesittelyiden vaikutus kalvoerotusprosessien toimintaan paperinvalmistuksen vesikierroissa - EKT 01

Energy Technology Data Exchange (ETDEWEB)

Nuortila-Jokinen, J.; Nystroem, M. [Lappeenranta Univ. of Technology (Finland). Dept. of Chemical Technology

1998-12-31

The aim of this project is to establish an optimized membrane filtration process for internal water treatment in the pulp and paper industry. In membrane filtration fouling reduces the capacity of a plant, and frequent or ineffective membrane washing reduces the membrane lifetime. These factors affect directly the feasibility of the process. Moreover, the retentates have to be economically destroyed. In this project effective pretreatment systems for membrane filtration processes will be developed. The pretreatments studied will be chemical, biological (thermophilic aerobic or anaerobic processes), oxidative (ozonation or other AOP methods) or enzymatic methods or their combinations. The target is to increase capacity and/or reduce fouling in the membrane process. In addition, the effect of the different pretreatment methods on the washability of the membranes will be studied and an optimized washing routine will be developed. The composition of the forming retentates are also affected by the pretreatment used and additionally the same methods can be used for developing a sensible and economically feasible retentate posttreatment method, which will also be developed in the project. (orig.)

The effect of pretreatment on the performance of membrane separation processes in the circulation water systems of paper production; Esikaesittelyiden vaikutus kalvoerotusprosessien toimintaan paperinvalmistuksen vesikierroissa - EKT 01

Energy Technology Data Exchange (ETDEWEB)

Nuortila-Jokinen, J; Nystroem, M [Lappeenranta Univ. of Technology (Finland). Dept. of Chemical Technology

1999-12-31

The aim of this project is to establish an optimized membrane filtration process for internal water treatment in the pulp and paper industry. In membrane filtration fouling reduces the capacity of a plant, and frequent or ineffective membrane washing reduces the membrane lifetime. These factors affect directly the feasibility of the process. Moreover, the retentates have to be economically destroyed. In this project effective pretreatment systems for membrane filtration processes will be developed. The pretreatments studied will be chemical, biological (thermophilic aerobic or anaerobic processes), oxidative (ozonation or other AOP methods) or enzymatic methods or their combinations. The target is to increase capacity and/or reduce fouling in the membrane process. In addition, the effect of the different pretreatment methods on the washability of the membranes will be studied and an optimized washing routine will be developed. The composition of the forming retentates are also affected by the pretreatment used and additionally the same methods can be used for developing a sensible and economically feasible retentate posttreatment method, which will also be developed in the project. (orig.)

Patterns of pretreatment diagnostic assessment and staging for patients with cervical cancer (1999-2001). Patterns of care study in Japan

International Nuclear Information System (INIS)

Toita, Takafumi; Kodaira, Takeshi; Uno, Takashi; Shinoda, Atsunori; Akino, Yuichi; Teshima, Teruki; Mitsumori, Michihide

2008-01-01

The objective of this study was to evaluate the patterns of pretreatment diagnostic assessment in uterine cervical cancer patients treated with definitive radiotherapy in Japan. The Japanese Patterns of Care Study working group conducted a second extramural audit survey of 68 institutions and collected specific information on 631 patients with cervical cancer. All patients were treated with radiotherapy in 1999-2001. Of these, 324 patients treated without surgery were the subjects of this study. International Federation of Gynecology and Obstetrics-prescribed diagnostic procedures were performed at moderate rates in our study cohort. The performance rates of chest X-ray, intravenous urography, cystoscopy, and proctoscopy were 74, 54, 53, and 33%, respectively. Cross sectional imaging studies were frequently performed. Pelvic CT, abdominal CT, and pelvic MRI were performed in 88, 80, and 76%, respectively. Lymphangiography (1%) and surgical evaluation (1%) were rarely done. Only one patient underwent positron emission tomography (PET) scans in this survey period. This study demonstrated the patterns of pretreatment diagnostic assessment in cervical cancer patients treated with definitive radiotherapy in Japan. (author)

Trus and MRI should not be used to stage patients with prostate cancer: an outcome based analysis

International Nuclear Information System (INIS)

Pinover, W. H.; Hanlon, A. L.; Kaplan, E. J.; Lee, W. R.; Hanks, G. E.

1995-01-01

Purpose/Objective: The AJCC staging of prostate cancer relies upon DRE findings, but suggests using all available information, including prostate imaging studies, prior to definitive treatment of prostate cancer. We have examined whether imaging upstaged patients have a different outcome from those not upstaged after treatment with external beam radiation therapy. Methods and Materials: The records of 348 patients with clinically localized adenocarcinoma of the prostate treated with definitive external beam irradiation alone from (1(86)) - (12(93)) were reviewed. All patients had at least one of the following pretreatment imaging modalities performed - transrectal ultrasound (TRUS), pelvic, endorectal, or Helmholtz MRI. Patients were assigned two clinical stage one based only on palpation criteria and the second allowing for any upstaging by imaging abnormalities. The Kaplan-Meier method was used to estimate bNED survival where a failure is defined as a PSA ≥ 1.5 and rising. Differences in outcome were evaluated by the log-rank test. Results: Overall upstaging by TRUS or MRI to any higher stage occurred in 115 of 312 (37%) palpation T1c-T2c patients. There was no significant difference in bNED survival for those upstaged compared to those not upstaged. Twenty one of 244 (9%) T1c-T2b patients were upstaged to T2c (bilobar disease). No significant difference in bNED survival was noted for those upstaged to bilobar disease compared to those not upstaged (see table). Upstaging to T3 occurred in 32 of 312 (10%) palpation T1c-T2c patients (T3a-5%, T3b-<1%, T3c-5%). No significant difference in bNED survival was noted for those upstaged to T3 compared to those not upstaged (see table). Comparison of palpation T3 patients with imaging upstaged T3 patients demonstrated a significant difference in bNED survival (p=.01 see table). Controlling for pretreatment PSA, this difference remained significant (p=0.01). Conclusions: Using the endpoint of biochemical NED survival

UV/H2O2 process performance improvement by ultrafiltration and physicochemical clarification systems for industrial effluent pretreatment

Directory of Open Access Journals (Sweden)

Ivanildo Hespanhol

2012-12-01

Full Text Available The present study evaluated the removal of TOC from an effluent with high organic load resulted from the treatment of oil-water emulsion by thermal process. Hollow Fiber Ultrafiltration membrane (HF-UF and physicochemical clarification process were used as pretreatment options to assess the influence of feed effluent quality on the UV/H2O2 oxidation process. Results for TOC removals showed HF-UF and physicochemical clarification processes can significantly improve the efficiency of UV/H2O2 oxidation process, when compared with the direct effluent oxidation. Reaction time for obtaining a TOC removal higher than 90% was reduced to approximately half of the time needed when no pretreatment was applied. Considering both pretreatment processes it was not possible to notice any significant difference on the UV/H2O2 oxidation process performance. However, the complexity of physicochemical process due to the use of three different chemicals and sludge production made the HF-UF process the best pretreatment alternative, without increasing the Total Dissolved Solids of the effluent, a very important issue when water reuse is considered.

Pretreating lignocellulosic biomass by the concentrated phosphoric acid plus hydrogen peroxide (PHP) for enzymatic hydrolysis: evaluating the pretreatment flexibility on feedstocks and particle sizes.

Science.gov (United States)

Wang, Qing; Wang, Zhanghong; Shen, Fei; Hu, Jinguang; Sun, Fubao; Lin, Lili; Yang, Gang; Zhang, Yanzong; Deng, Shihuai

2014-08-01

In order to seek a high-efficient pretreatment path for converting lignocellulosic feedstocks to fermentable sugars by enzymatic hydrolysis, the concentrated H₃PO₄ plus H₂O₂ (PHP) was attempted to pretreat different lignocellulosic biomass for evaluating the pretreatment flexibility on feedstocks. Meanwhile, the responses of pretreatment to particle sizes were also evaluated. When the PHP-pretreatment was employed (final H₂O₂ and H₃PO₄ concentration of 1.77% and 80.0%), 71-96% lignin and more than 95% hemicellulose in various feedstocks (agricultural residues, hardwood, softwood, bamboo, and their mixture, and garden wastes mixture) can be removed. Consequently, more than 90% glucose conversion was uniformly achieved indicating PHP greatly improved the pretreatment flexibility to different feedstocks. Moreover, when wheat straw and oak chips were PHP-pretreated with different sizes, the average glucose conversion reached 94.9% and 100% with lower coefficient of variation (7.9% and 0.0%), which implied PHP-pretreatment can significantly weaken the negative effects of feedstock sizes on subsequent conversion. Copyright © 2014 Elsevier Ltd. All rights reserved.

NON-POLLUTING METAL SURFACE FINISHING PRETREATMENT AND PRETREATMENT/CONVERSION COATING

Science.gov (United States)

Picklex, a proprietary formulation, is an alterantive to conventional metal surface pretreatments and is claimed not to produce waste or lower production or lower performance. A laboratory program was designed to evaluate Picklex in common, large scale, polluting surface finishin...

Dilute alkali pretreatment of softwood pine: A biorefinery approach.

Science.gov (United States)

Safari, Ali; Karimi, Keikhosro; Shafiei, Marzieh

2017-06-01

Dilute alkali pretreatment was performed on softwood pine to maximize ethanol and biogas production via a biorefinery approach. Alkali pretreatments were performed with 0-2% w/v NaOH at 100-180°C for 1-5h. The liquid fraction of the pretreated substrates was subjected to anaerobic digestion. The solid fraction of the pretreatment was used for separate enzymatic hydrolysis and fermentation. High ethanol yields of 76.9‒78.0% were achieved by pretreatment with 2% (w/v) NaOH at 180°C. The highest biogas yield of 244mL/g volatile solid (at 25°C, 1bar) was achieved by the pretreatment with 1% (w/v) NaOH at 180°C. The highest gasoline equivalent (sum of ethanol and methane) of 197L per ton of pinewood and the lowest ethanol manufacturing cost of 0.75€/L was obtained after pretreatment with 1% NaOH at 180°C for 5h. The manufacturing cost of ethanol from untreated wood was 4.12€/L. Copyright © 2017 Elsevier Ltd. All rights reserved.

Influence of dispatching rules on average production lead time for multi-stage production systems.

Science.gov (United States)

Hübl, Alexander; Jodlbauer, Herbert; Altendorfer, Klaus

2013-08-01

In this paper the influence of different dispatching rules on the average production lead time is investigated. Two theorems based on covariance between processing time and production lead time are formulated and proved theoretically. Theorem 1 links the average production lead time to the "processing time weighted production lead time" for the multi-stage production systems analytically. The influence of different dispatching rules on average lead time, which is well known from simulation and empirical studies, can be proved theoretically in Theorem 2 for a single stage production system. A simulation study is conducted to gain more insight into the influence of dispatching rules on average production lead time in a multi-stage production system. We find that the "processing time weighted average production lead time" for a multi-stage production system is not invariant of the applied dispatching rule and can be used as a dispatching rule independent indicator for single-stage production systems.

LOX/LH2 propulsion system for launch vehicle upper stage, test results

Science.gov (United States)

Ikeda, T.; Imachi, U.; Yuzawa, Y.; Kondo, Y.; Miyoshi, K.; Higashino, K.

1984-01-01

The test results of small LOX/LH2 engines for two propulsion systems, a pump fed system and a pressure fed system are reported. The pump fed system has the advantages of higher performances and higher mass fraction. The pressure fed system has the advantages of higher reliability and relative simplicity. Adoption of these cryogenic propulsion systems for upper stage of launch vehicle increases the payload capability with low cost. The 1,000 kg thrust class engine was selected for this cryogenic stage. A thrust chamber assembly for the pressure fed propulsion system was tested. It is indicated that it has good performance to meet system requirements.

Microbial pretreatment of cotton stalks by Phanerochaete chrysosporium for bioethanol production

Science.gov (United States)

Shi, Jian

Lignocellulosic biomass has been recognized as a widespread, potentially low cost renewable source of mixed sugars for fermentation to fuel ethanol. Pretreatment, as the first step towards conversion of lignocellulose to ethanol, remains one of the main barriers to technical and commercial success of the processing technology. Existing pretreatment methods have largely been developed on the basis of physiochemical technologies which are considered relatively expensive and usually involve adverse environmental impacts. In this study, an environmentally benign alternative, microbial pretreatment using Phanerochaete chrysosporium, was explored to degrade lignin in cotton stalks and facilitate their conversion into ethanol. Two submerged liquid pretreatment techniques (SmC), shallow stationary and agitated cultivation, at three inorganic salt concentrations (no salts, modified salts without Mn2+, modified salts with Mn2+) were compared by evaluating their pretreatment efficiencies. Shallow stationary cultivation with no salt was superior to other pretreatment conditions and gave 20.7% lignin degradation along with 76.3% solids recovery and 29.0% carbohydrate availability over a 14 day period. The influence of substrate moisture content (65%, 75% and 80% M.C. wet-basis), inorganic salt concentration (no salts, modified salts without Mn2+ , modified salts with Mn2+) and culture time (0-14 days) on pretreatment effectiveness in solid state (SSC) systems was also examined. It was shown that solid state cultivation at 75% M.C. without salts was the most preferable pretreatment resulting in 27.6% lignin degradation, 71.1% solids recovery and 41.6% carbohydrate availability over a period of 14 days. A study on hydrolysis and fermentation of cotton stalks treated microbially using the most promising SmC (shallow stationary, no salts) and SSC (75% moisture content, no salts) methods resulted in no increase in cellulose conversion with direct enzyme application (10.98% and 3

Comparative Effects of Biomass Pre-Treatments for Direct and Indirect Transesterification to Enhance Microalgal Lipid Recovery

International Nuclear Information System (INIS)

Ghasemi Naghdi, Forough; Thomas-Hall, Skye R.; Durairatnam, Reuben; Pratt, Steven; Schenk, Peer M.

2014-01-01

Microalgal lipid recovery for biodiesel production is currently considered suboptimal, but pre-treatment of algal biomass, the use of solvent mixtures and the positioning of transesterification can lead to increased yields. Here, the effect of various reportedly successful pre-treatments and solvent mixtures were directly compared to each other and combined with direct and indirect transesterification methods using the oleaginous microalga Tetraselmis sp. M8. Microwave and thermal pre-treatments were applied and the total lipid and fatty acid methyl ester (FAME) recoveries were investigated. The application of pre-treatments increased FAME recovery through indirect transesterification when a Soxhlet system was used but they had no significant effect for direct transesterification. Gravimetric analyses of total lipids revealed that lipid recovery was highest when utilizing the chloroform-based Bligh and Dyer extraction method; however, FAME yield was the highest when applying a Soxhlet system utilizing a solvent mixture of hexane–ethanol (3:1). Total lipid recovery did not necessarily correlate with the recovery of FAMEs. The highest FAME recovery was achieved from thermal or microwave pre-treated biomass followed by indirect transesterification through Soxhlet extraction. FAME recovery could be more than doubled (increase of up to 171%) under these conditions. We conclude that a simple thermal pre-treatment (80°C for 10 min) in combination with solvent mixture extraction through indirect transesterification may present a cost-effective and scalable option for large-scale lipid extraction from microalgae.

Comparative effects of biomass pre-treatments for direct and indirect transesterification to enhance microalgal lipid recovery

Directory of Open Access Journals (Sweden)

Forough eGhasemi Naghdi

2014-12-01

Full Text Available Microalgal lipid recovery for biodiesel production is currently considered suboptimal, but pre-treatment of algal biomass, the use of solvent mixtures and the positioning of transesterification can lead to increased yields. Here, the effect of various reportedly successful pre-treatments and solvent mixtures were directly compared to each other and combined with direct and indirect transesterification methods using the oleaginous microalga Tetraselmis sp. M8. Microwave and thermal pre-treatments were applied and the total lipid and fatty acid methyl ester (FAME recoveries were investigated. The application of pre-treatments increased FAME recovery through indirect transesterification when a Soxhlet system was used but they had no significant effect for direct transesterification. Gravimetric analyses of total lipids revealed that lipid recovery was highest when utilizing the chloroform-based Bligh and Dyer extraction method; however FAME yield was the highest when applying a Soxhlet system utilizing a solvent mixture of hexane-ethanol (3:1. Total lipid recovery did not necessarily correlate with the recovery of FAMEs. The highest FAME recovery was achieved from thermal or microwave pre-treated biomass followed by indirect transesterification through Soxhlet extraction. FAME recovery could be more than doubled (increase of up to 171% under these conditions. We conclude that a simple thermal pre-treatment (80°C for 10 min in combination with solvent mixture extraction through indirect transesterification may present a cost-effective and scalable option for large-scale lipid extraction from microalgae.

Comparative Effects of Biomass Pre-Treatments for Direct and Indirect Transesterification to Enhance Microalgal Lipid Recovery

Energy Technology Data Exchange (ETDEWEB)

Ghasemi Naghdi, Forough; Thomas-Hall, Skye R.; Durairatnam, Reuben [Algae Biotechnology Laboratory, School of Agriculture and Food Sciences, The University of Queensland, Brisbane, QLD (Australia); Pratt, Steven [School of Chemical Engineering, The University of Queensland, Brisbane, QLD (Australia); Schenk, Peer M., E-mail: p.schenk@uq.edu.au [Algae Biotechnology Laboratory, School of Agriculture and Food Sciences, The University of Queensland, Brisbane, QLD (Australia)

2014-12-04

Microalgal lipid recovery for biodiesel production is currently considered suboptimal, but pre-treatment of algal biomass, the use of solvent mixtures and the positioning of transesterification can lead to increased yields. Here, the effect of various reportedly successful pre-treatments and solvent mixtures were directly compared to each other and combined with direct and indirect transesterification methods using the oleaginous microalga Tetraselmis sp. M8. Microwave and thermal pre-treatments were applied and the total lipid and fatty acid methyl ester (FAME) recoveries were investigated. The application of pre-treatments increased FAME recovery through indirect transesterification when a Soxhlet system was used but they had no significant effect for direct transesterification. Gravimetric analyses of total lipids revealed that lipid recovery was highest when utilizing the chloroform-based Bligh and Dyer extraction method; however, FAME yield was the highest when applying a Soxhlet system utilizing a solvent mixture of hexane–ethanol (3:1). Total lipid recovery did not necessarily correlate with the recovery of FAMEs. The highest FAME recovery was achieved from thermal or microwave pre-treated biomass followed by indirect transesterification through Soxhlet extraction. FAME recovery could be more than doubled (increase of up to 171%) under these conditions. We conclude that a simple thermal pre-treatment (80°C for 10 min) in combination with solvent mixture extraction through indirect transesterification may present a cost-effective and scalable option for large-scale lipid extraction from microalgae.

Pretreatment of Cellulose By Electron Beam Irradiation Method

Science.gov (United States)

Jusri, N. A. A.; Azizan, A.; Ibrahim, N.; Salleh, R. Mohd; Rahman, M. F. Abd

2018-05-01

Pretreatment process of lignocellulosic biomass (LCB) to produce biofuel has been conducted by using various methods including physical, chemical, physicochemical as well as biological. The conversion of bioethanol process typically involves several steps which consist of pretreatment, hydrolysis, fermentation and separation. In this project, microcrystalline cellulose (MCC) was used in replacement of LCB since cellulose has the highest content of LCB for the purpose of investigating the effectiveness of new pretreatment method using radiation technology. Irradiation with different doses (100 kGy to 1000 kGy) was conducted by using electron beam accelerator equipment at Agensi Nuklear Malaysia. Fourier Transform Infrared Spectroscopy (FTIR) and X-Ray Diffraction (XRD) analyses were studied to further understand the effect of the suggested pretreatment step to the content of MCC. Through this method namely IRR-LCB, an ideal and optimal condition for pretreatment prior to the production of biofuel by using LCB may be introduced.

Photocatalytic pretreatment of oily wastewater from the restaurant by a vacuum ultraviolet/TiO2 system

International Nuclear Information System (INIS)

Kang Jianxiong; Lu Lu; Zhan Wei; Li Bo; Li Daosheng; Ren Yongzheng; Liu Dongqi

2011-01-01

The present study aims at investigating the performance of a vacuum ultraviolet (VUV, 185 nm) and TiO 2 oxidation system for the pretreatment of oily wastewater from restaurant. The influence of irradiation time, pH, dissolved oxygen (DO), the dosage of TiO 2 and the initial chemical oxygen demand (COD) concentration on COD removal efficiency was ascertained and optimum process conditions for stable and effective operation were determined. Under the optimum conditions of irradiation 10 min, initial COD 3981 mg/L, TiO 2 150 mg/L, pH 7.0 and flow rate of air 40 L/h, the process of VUV and TiO 2 /VUV achieved removal efficiencies of COD, BOD 5 and oil as 50 ± 3%, 37 ± 2%, 86 ± 3%, and 63 ± 3%, 43 ± 2%, 70 ± 3%, respectively. The biodegradability factor f B of the wastewater was determined as 1.56 which indicated that the VUV/TiO 2 process improved the biodegradability of the oily wastewater significantly. Results clearly indicate that VUV/TiO 2 photolysis tends to destruct parts of COD, BOD 5 , and ammonia, as well as enhances the biodegradability of the oily wastewater simultaneously. Thus, this technique could be used as a pretreatment step for conventional biological treatment of oily wastewater.

Photocatalytic pretreatment of oily wastewater from the restaurant by a vacuum ultraviolet/TiO2 system.

Science.gov (United States)

Kang, Jian-xiong; Lu, Lu; Zhan, Wei; Li, Bo; Li, Dao-sheng; Ren, Yong-zheng; Liu, Dong-qi

2011-02-15

The present study aims at investigating the performance of a vacuum ultraviolet (VUV, 185 nm) and TiO(2) oxidation system for the pretreatment of oily wastewater from restaurant. The influence of irradiation time, pH, dissolved oxygen (DO), the dosage of TiO(2) and the initial chemical oxygen demand (COD) concentration on COD removal efficiency was ascertained and optimum process conditions for stable and effective operation were determined. Under the optimum conditions of irradiation 10 min, initial COD 3981 mg/L, TiO(2) 150 mg/L, pH 7.0 and flow rate of air 40 L/h, the process of VUV and TiO(2)/VUV achieved removal efficiencies of COD, BOD(5) and oil as 50±3%, 37±2%, 86±3%, and 63±3%, 43±2%, 70±3%, respectively. The biodegradability factor f(B) of the wastewater was determined as 1.56 which indicated that the VUV/TiO(2) process improved the biodegradability of the oily wastewater significantly. Results clearly indicate that VUV/TiO(2) photolysis tends to destruct parts of COD, BOD(5), and ammonia, as well as enhances the biodegradability of the oily wastewater simultaneously. Thus, this technique could be used as a pretreatment step for conventional biological treatment of oily wastewater. Copyright © 2010 Elsevier B.V. All rights reserved.

Pretreatment Apparent Diffusion Coefficient of the Primary Lesion Correlates With Local Failure in Head-and-Neck Cancer Treated With Chemoradiotherapy or Radiotherapy

International Nuclear Information System (INIS)

Hatakenaka, Masamitsu; Nakamura, Katsumasa; Yabuuchi, Hidetake; Shioyama, Yoshiyuki; Matsuo, Yoshio; Ohnishi, Kayoko; Sunami, Shunya; Kamitani, Takeshi; Setoguchi, Taro; Yoshiura, Takashi; Nakashima, Torahiko; Nishikawa, Kei; Honda, Hiroshi

2011-01-01

Purpose: This study was performed to evaluate whether the apparent diffusion coefficient (ADC) of a primary lesion correlates with local failure in primary head-and-neck squamous cell carcinoma (HNSCC) treated with chemoradiotherapy or radiotherapy. Methods and Materials: We retrospectively studied 38 patients with primary HNSCC (12 oropharynx, 20 hypopharynx, 4 larynx, 2 oral cavity) treated with chemoradiotherapy or radiotherapy with radiation dose to gross tumor volume equal to or over 60 Gy and who underwent pretreatment magnetic resonance imaging, including diffusion-weighted imaging. Ten patients developed local failure during follow-up periods of 2.0 to 9.3 months, and the remaining 28 showed local control during follow-up periods of 10.5 to 31.7 months. The variables that could affect local failure (age, tumor volume, ADC, T stage, N stage, dose, treatment method, tumor location, and overall treatment time) were analyzed using logistic regression analyses for all 38 patients and for 17 patients with Stage T3 or T4 disease. Results: In univariate logistic analysis for all 38 cases, tumor volume, ADC, T stage, and treatment method showed significant (p < 0.05) associations with local failure. In multivariate analysis, ADC and T stage revealed significance (p < 0.01). In univariate logistic analysis for the 17 patients with Stage T3 or T4 disease, ADC and dose showed significant (p < 0.01) associations with local failure. In multivariate analysis, ADC alone showed significance (p < 0.05). Conclusions: The results suggest that pretreatment ADC, along with T stage, is a potential indicator of local failure in HNSCC treated with chemoradiotherapy or radiotherapy.

Genetic and cytokine changes associated with symptomatic stages of CLL.

Science.gov (United States)

Agarwal, Amit; Cooke, Lawrence; Riley, Christopher; Qi, Wenqing; Mount, David; Mahadevan, Daruka

2014-09-01

The pathogenesis and drug resistance of symptomatic CLL patients involves genetic changes associated with the CLL clone as well as changes within the microenvironment. To further understand these processes, we compared early stage CLL to symptomatic late stage using gene expression and serum cytokine profiling to gain insight of the genetic and microenvironment changes associated with the most severe form of the disease. Patients were classified into low stage (Rai stage 0/I/II) and high stage (Rai stage III/IV). Gene expression profiles were obtained on pretreatment samples using the HG-U133A 2.0 Affymetrix platform. A comparison of low versus high stage CLL revealed a set of 21 genes differentially expressed genes. 15 genes were up regulated in the high stage compared to low stage while 6 genes were down regulated. Analysis of GO molecular function revealed 9 of 21 genes were involved in transcription factor activity. Serum cytokine profiles showed six cytokines to be significantly different in high stage patients. Two chemokines, SDF-1/CXCL12 and uPAR known to be involved in stem cell mobilization and homing were increased in serum of high stage patients. This study has identified therapeutic targets for symptomatic CLL patients. Copyright © 2014 Elsevier Ltd. All rights reserved.

Structural changes of corn stover lignin during acid pretreatment.

Science.gov (United States)

Moxley, Geoffrey; Gaspar, Armindo Ribeiro; Higgins, Don; Xu, Hui

2012-09-01

In this study, raw corn stover was subjected to dilute acid pretreatments over a range of severities under conditions similar to those identified by the National Renewable Energy Laboratory (NREL) in their techno-economic analysis of biochemical conversion of corn stover to ethanol. The pretreated corn stover then underwent enzymatic hydrolysis with yields above 70 % at moderate enzyme loading conditions. The enzyme exhausted lignin residues were characterized by ³¹P NMR spectroscopy and functional moieties quantified and correlated to enzymatic hydrolysis yields. Results from this study indicated that both xylan solubilization and lignin degradation are important for improving the enzyme accessibility and digestibility of dilute acid pretreated corn stover. At lower pretreatment temperatures, there is a good correlation between xylan solubilization and cellulose accessibility. At higher pretreatment temperatures, lignin degradation correlated better with cellulose accessibility, represented by the increase in phenolic groups. During acid pretreatment, the ratio of syringyl/guaiacyl functional groups also gradually changed from less than 1 to greater than 1 with the increase in pretreatment temperature. This implies that more syringyl units are released from lignin depolymerization of aryl ether linkages than guaiacyl units. The condensed phenolic units are also correlated with the increase in pretreatment temperature up to 180 °C, beyond which point condensation reactions may overtake the hydrolysis of aryl ether linkages as the dominant reactions of lignin, thus leading to decreased cellulose accessibility.

Efficient bioconversion of rice straw to ethanol with TiO2/UV pretreatment.

Science.gov (United States)

Kang, Hee-Kyoung; Kim, Doman

2012-01-01

Rice straw is a lignocellulosic biomass that constitutes a renewable organic substance and alternative source of energy; however, its structure confounds the liberation of monosaccharides. Pretreating rice straw using a TiO(2)/UV system facilitated its hydrolysis with Accellerase 1000(™), suggesting that hydroxyl radicals (OH·) from the TiO(2)/UV system could degrade lignin and carbohydrates. TiO(2)/UV pretreatment was an essential step for conversion of hemicellulose to xylose; optimal conditions for this conversion were a TiO(2) concentration of 0.1% (w/v) and an irradiation time of 2 h with a UV-C lamp at 254 nm. After enzymatic hydrolysis, the sugar yields from rice straw pretreated with these parameters were 59.8 ± 0.7% of the theoretical for glucose (339 ± 13 mg/g rice straw) and 50.3 ± 2.8% for xylose (64 ± 3 mg/g rice straw). The fermentation of enzymatic hydrolysates containing 10.5 g glucose/L and 3.2 g xylose/L with Pichia stipitis produced 3.9 g ethanol/L with a corresponding yield of 0.39 g/g rice straw. The maximum possible ethanol conversion rate is 76.47%. TiO(2)/UV pretreatment can be performed at room temperature and atmospheric pressure and demonstrates potential in large-scale production of fermentable sugars.

Prognostic value of pretreatment volume-based quantitative {sup 18}F-FDG PET/CT parameters in patients with malignant pleural mesothelioma

Energy Technology Data Exchange (ETDEWEB)

Kitajima, Kazuhiro, E-mail: kitajima@med.kobe-u.ac.jp [Division of Nuclear Medicine and PET Center, Department of Radiology, Hyogo College of Medicine, Hyogo (Japan); Doi, Hiroshi, E-mail: h-doi@hyo-med.ac.jp [Department of Radiology, Hyogo College of Medicine, Hyogo (Japan); Kuribayashi, Kozo, E-mail: kuririn@hyo-med.ac.jp [Division of Respiratory Medicine, Department of Internal Medicine, Hyogo College of Medicine, Hyogo (Japan); Hashimoto, Masaki, E-mail: kogekogemasaki@gmail.com [Department of Thoracic Surgery, Hyogo College of Medicine, Hyogo (Japan); Tsuchitani, Tatsuya, E-mail: tty-823@hyo-med.ac.jp [Department of Radiological Technology, Hyogo College of Medicine College Hospital, Hyogo (Japan); Tanooka, Masao, E-mail: masao1108@gmail.com [Department of Radiological Technology, Hyogo College of Medicine College Hospital, Hyogo (Japan); Fukushima, Kazuhito, E-mail: fukuchan00106@gmail.com [Division of Nuclear Medicine and PET Center, Department of Radiology, Hyogo College of Medicine, Hyogo (Japan); Nakano, Takashi, E-mail: t-nakano@hyo-med.ac.jp [Division of Respiratory Medicine, Department of Internal Medicine, Hyogo College of Medicine, Hyogo (Japan); Hasegawa, Seiki, E-mail: hasegawa@hyo-med.ac.jp [Department of Thoracic Surgery, Hyogo College of Medicine, Hyogo (Japan); Hirota, Shozo, E-mail: hirota-s@hyo-med.ac.jp [Department of Radiology, Hyogo College of Medicine, Hyogo (Japan)

2017-01-15

Purpose: To investigate the relationships between pretreatment volume-based quantitative {sup 18}F-fluorodeoxyglucose (FDG) positron emission tomography/computed tomography (PET/CT) parameters and overall survival (OS) in patients with malignant pleural mesothelioma (MPM). Materials and methods: We retrospectively reviewed data from 201 MPM patients, of whom 38 underwent surgical resection, and calculated the maximum standardized uptake value (SUVmax), metabolic tumor volume (MTV), and total lesion glycolysis (TLG), including primary tumors and nodal or distant metastatic lesions, on pretreatment {sup 18}F-FDG PET/CT. Relationships between clinicopathological factors (age, sex, performance status, European Organization for Research and Treatment of Cancer [EORTC] score, histological subtype, TNM stage, and treatment strategy), volume-based quantitative PET/CT parameters, and OS were evaluated using a Cox proportional hazards model and log-rank test. Results: The median follow-up was 15 months (range, 1–96 months; median, 17 months). In a univariate analysis of all patients, older age (p < 0.05), high EORTC score (p < 0.001), non-epithelioid histological subtype (p < 0.001), high T stage (p < 0.001), positive N/M status (p < 0.05, p < 0.001), advanced TNM stage (p < 0.001), non-surgical treatment (p < 0.001), and high SUVmax (p < 0.001), MTV (p < 0.001), or TLG (p < 0.001) were associated with significantly shorter OS. A multivariate analysis confirmed non-epithelioid subtype (hazard ratio [HR]: 1.69, 95% confidence interval [CI]: 1.14–2.48; p < 0.05), non-surgical treatment (HR: 0.58, 95% CI: 0.34–0.95; p < 0.05), and high TLG (HR: 1.97, 95% CI: 1.14–3.44; p < 0.05) as independent negative predictors. Conclusions: Pretreatment volume-based quantitative {sup 18}F-FDG PET/CT parameters, especially TLG, could serve as potential surrogate markers for MPM prognosis.

NxStage dialysis system-associated thrombocytopenia: a report of two cases.

Science.gov (United States)

Sekkarie, Mohamed; Waldron, Michelle; Reynolds, Texas

2016-01-01

Thrombocytopenia in hemodialysis patients has recently been reported to be commonly caused by electron-beam sterilization of dialysis filters. We report the occurrence of thrombocytopenia in the first two patients of a newly established home hemodialysis program. The 2 patients switched from conventional hemodialysis using polysulfone electron-beam sterilized dialyzers to a NxStage system, which uses gamma sterilized polyehersulfone dialyzers incorporated into a drop-in cartridge. The thrombocytopenia resolved after return to conventional dialysis in both patients and recurred upon rechallenge in the patient who opted to retry NxStage. This is the first report of thrombocytopenia with the NxStage system according to the authors’ knowledge. Dialysis-associated thrombocytopenia pathophysiology and clinical significance are not well understood and warrant additional investigations.

UHPLC-LTQ-Orbitrap MS combined with spike-in method for plasma metabonomics analysis of acute myocardial ischemia rats and pretreatment effect of Danqi Tongmai tablet.

Science.gov (United States)

Yan, Bingpeng; Deng, Yanping; Hou, Jinjun; Bi, Qirui; Yang, Min; Jiang, Baohong; Liu, Xuan; Wu, Wanying; Guo, Dean

2015-02-01

Undoubtedly, metabonomics can reveal the comprehensive efficacies of traditional Chinese medicine (TCM) formulae and its complex mechanism at the molecular biological level. In this study, an attempt was made to address the pretreatment effect of a TCM formula. In this case, as a critical point, we should first know how to really reflect the various endogenous metabolites in a disease status before a TCM formula is employed in a therapeutic procedure. Here, we explored an approach that combined high resolution LTQ-Orbitrap mass spectrometry with a spike-in method to characterize endogenous metabolites in acute myocardial ischemia (AMI) rats. As a result, 19 potential biomarkers in rat plasma were identified and 10 related disturbed pathways were perturbed in the early stages of AMI development. Subsequently, the metabonomics method was applied to investigate the pretreatment effect of the TCM formula named the Danqi Tongmai tablet (DQTM). The results revealed that the DQTM pretreatment could reduce the AMI injury and partially regulate the perturbed TCA cycle and amino and nucleotide metabolism, which were presumable related to energy metabolism and myocardial cells apoptosis/necrosis. In conclusion, UHPLC-LTQ-Orbitrap MS combined with a spike-in method were successfully applied to the metabonomics analysis of DQTM, which demonstrated that not only a comprehensive metabolic profile in the early stages of AMI development was achieved, but also that the underlying holistic efficacies were assessed and it was helpful to understand the possible mechanism of pretreatment with DQTM.

MR staging accuracy for endometrial cancer based on the new FIGO stage

International Nuclear Information System (INIS)

Shin, Kyung Eun; Park, Byung Kwan; Kim, Chan Kyo; Bae, Duk Soo; Song, Sang Yong; Kim, Bohyun

2011-01-01

Background: Magnetic resonance imaging (MRI) has been frequently used to determine a preoperative treatment plan for gynecologic cancers. However, the MR accuracy for staging an endometrial cancer is not satisfactory based on the old FIGO staging system. Purpose: To evaluate MR accuracy for staging endometrial cancer using the new FIGO staging system. Material and Methods: Between January 2005 and May 2009, 199 women underwent surgery due to endometrial cancer. In each patient, an endometrial cancer was staged using MR findings based on the old FIGO staging system and then repeated according to the new FIGO staging system for comparison. Histopathologic findings were used as a standard of reference. Results: The accuracy of MRI in the staging of endometrial carcinoma stage I, II, III, and IV using the old FIGO staging system were 80% (159/199), 89% (178/199), 90% (179/199), and 99% (198/199), respectively, compared to 87% (174/199), 97% (193/199), 90% (179/199), and 99% (198/199), respectively, when using the new FIGO staging criteria. The overall MR accuracy of the old and new staging systems were 51% (101/199) and 81% (161/199), respectively. Conclusion: MRI has become a more useful tool in the preoperative staging of endometrial cancers using the new FIGO staging system compared to the old one with increased accuracy

The Effect of Ultrasound Pretreatment on Poplar Wood Dimensional Stability

Directory of Open Access Journals (Sweden)

Shu Qiu

2016-08-01

Full Text Available Dimensional stability is a key property of wood that significantly affects its applications. The effect of an ultrasound pretreatment on poplar wood (Populous tomentosa dimensional stability was examined. During the pretreatments, wood samples were immersed in distilled water and treated ultrasonically under three different powers and frequencies. The samples were then analyzed by Fourier transform infrared spectroscopy (FTIR and X-ray diffraction (XRD. The chemical transformation of the cell-wall material was studied and then associated with the change of water absorption and the swelling coefficient. The results showed that the water absorption decreased after the ultrasonic pretreatment. The axial and radial swelling coefficients of the pretreated samples decreased, while the tangential swelling coefficients increased. The volumetric swelling coefficient of pretreated specimens fluctuated near 4.48% (the volumetric swelling coefficient of untreated wood. Ultrasonic pretreatment increased the number of hydrophilic groups, such as the hydroxyl, acetyl, and uronic ester groups. Meanwhile, the pretreatment also increased the degree of crystallinity and reduced the available polar groups. These two factors together caused the change of the moisture absorption and the swelling coefficient of the pretreated wood. These conclusions suggest that the ultrasonic pretreatment is a promising method for further chemical modification of wood.

Pretreatment of macroalgae for volatile fatty acid production.

Science.gov (United States)

Pham, Thi Nhan; Um, Youngsoon; Yoon, Hyon Hee

2013-10-01

In this study, a novel method was proposed for the biological pretreatment of macroalgae (Laminaria japonica, Pachymeniopsis elliptica, and Enteromorpha crinita) for production of volatile fatty acid (VFA) by anaerobic fermentation. The amount of VFA produced from 40 g/L of L. japonica increased from 8.3 g/L (control) to 15.6 g/L when it was biologically pretreated with Vibrio harveyi. The biological treatment of L. japonica with Vibrio spp. was most effective likely due to the alginate lyase activity of Vibrio spp. However, a considerable effect was also observed after biological pretreatment of P. elliptica and E. crinita, which are red and green algae, respectively. Alkaline pretreatment of 40 g/L of L. japonica with 0.5 N NaOH resulted in an increase of VFA production to 12.2 g/L. These results indicate that VFA production from macroalgae can be significantly enhanced using the proposed biological pretreatments. Copyright © 2013 Elsevier Ltd. All rights reserved.

Vibration isolation and dual-stage actuation pointing system for space precision payloads

Science.gov (United States)

Kong, Yongfang; Huang, Hai

2018-02-01

Pointing and stability requirements for future space missions are becoming more and more stringent. This work follows the pointing control method which consists of a traditional spacecraft attitude control system and a payload active pointing loop, further proposing a vibration isolation and dual-stage actuation pointing system for space precision payloads based on a soft Stewart platform. Central to the concept is using the dual-stage actuator instead of the traditional voice coil motor single-stage actuator to improve the payload active pointing capability. Based on a specified payload, the corresponding platform was designed to be installed between the spacecraft bus and the payload. The performance of the proposed system is demonstrated by preliminary closed-loop control investigations in simulations. With the ordinary spacecraft bus, the line-of-sight pointing accuracy can be controlled to below a few milliarcseconds in tip and tilt. Meanwhile, utilizing the voice coil motor with the softening spring in parallel, which is a portion of the dual-stage actuator, the system effectively achieves low-frequency motion transmission and high-frequency vibration isolation along the other four degree-of-freedom directions.

Biodelignification of lignocellulose substrates: An intrinsic and sustainable pretreatment strategy for clean energy production.

Science.gov (United States)

Chandel, Anuj K; Gonçalves, Bruna C M; Strap, Janice L; da Silva, Silvio S

2015-01-01

Lignocellulosic biomass (LB) is a promising sugar feedstock for biofuels and other high-value chemical commodities. The recalcitrance of LB, however, impedes carbohydrate accessibility and its conversion into commercially significant products. Two important factors for the overall economization of biofuel production is LB pretreatment to liberate fermentable sugars followed by conversion into ethanol. Sustainable biofuel production must overcome issues such as minimizing water and energy usage, reducing chemical usage and process intensification. Amongst available pretreatment methods, microorganism-mediated pretreatments are the safest, green, and sustainable. Native biodelignifying agents such as Phanerochaete chrysosporium, Pycnoporous cinnabarinus, Ceriporiopsis subvermispora and Cyathus stercoreus can remove lignin, making the remaining substrates amenable for saccharification. The development of a robust, integrated bioprocessing (IBP) approach for economic ethanol production would incorporate all essential steps including pretreatment, cellulase production, enzyme hydrolysis and fermentation of the released sugars into ethanol. IBP represents an inexpensive, environmentally friendly, low energy and low capital approach for second-generation ethanol production. This paper reviews the advancements in microbial-assisted pretreatment for the delignification of lignocellulosic substrates, system metabolic engineering for biorefineries and highlights the possibilities of process integration for sustainable and economic ethanol production.

Long-term carbimazole pretreatment reduces the efficacy of radioiodine therapy

Directory of Open Access Journals (Sweden)

C Shivaprasad

2015-01-01

Full Text Available Introduction: Data from several studies suggest that pretreatment with antithyroid drugs (ATD before 131 I increases the risk of treatment failure. This effect has been demonstrated more consistently with propylthiouracil than with carbimazole (CMZ or methimazole (MMI. Men with Graves′ disease (GD have a lower rate of remission with 131 I compared to women and the impact of long-term ATD pretreatment on the success of 131 I is unknown. The objective of our study was to compare the efficacy of fixed doses of radioiodine between patients with and without long-term CMZ pretreatment. Materials and Methods: We performed a retrospective study on 335 male patients with GD treated with 131 I from 1998 to 2008. 148 patients had been pretreated with CMZ, and the remaining 187 patients received 131 I without pretreatment. We compared the success rate of a single dose of 131 I, between patients with and without long-term CMZ pretreatment. Results: The success rate of a single dose of 131 I was significantly higher in patients without pretreatment than in patients who were pretreated with CMZ (91.4% vs. 82.3%, P = 0.01. The rate of hypothyroidism in the first 6 months after 131 I therapy was significantly higher in patients without pretreatment (55.1% vs. 44.6%, P = 0.05. There was also a trend for higher cumulative rate of hypothyroidism at last follow-up in nonpretreated patients (78.1% vs. 69.7%. Conclusion: Male patients with Graves′ hyperthyroidism pretreated with CMZ have lower efficacy with 131I therapy compared to nonpretreated patients. CMZ pretreatment given for a prolonged period reduces the efficacy of 131 I therapy.

Pretreatment on Corn Stover with Low Concentration of Formic Acid

DEFF Research Database (Denmark)

Xu, Jian; Thomsen, Mette Hedegaard; Thomsen, Anne Belinda

2009-01-01

the cellulose easily degraded into sugars and further fermented to ethanol. In this work, hydrothermal pretreatment on corn stover at 195 degrees for 15 min with and without lower concentration of formic acid was compared in terms of sugar recoveries and ethanol fermentation. For pretreatment with formic acid...... pretreatment without formic acid. Toxicity tests of liquor parts showed that there were no inhibitions found for both pretreatment conditions. After simultaneous saccharification and fermentation (SSF) of the pretreated corn stover with Baker's yeast, the highest ethanol yield of 76.5% of the theoretical...

Extrusion Pretreatment of Lignocellulosic Biomass: A Review

Directory of Open Access Journals (Sweden)

Jun Zheng

2014-10-01

Full Text Available Bioconversion of lignocellulosic biomass to bioethanol has shown environmental, economic and energetic advantages in comparison to bioethanol produced from sugar or starch. However, the pretreatment process for increasing the enzymatic accessibility and improving the digestibility of cellulose is hindered by many physical-chemical, structural and compositional factors, which make these materials difficult to be used as feedstocks for ethanol production. A wide range of pretreatment methods has been developed to alter or remove structural and compositional impediments to (enzymatic hydrolysis over the last few decades; however, only a few of them can be used at commercial scale due to economic feasibility. This paper will give an overview of extrusion pretreatment for bioethanol production with a special focus on twin-screw extruders. An economic assessment of this pretreatment is also discussed to determine its feasibility for future industrial cellulosic ethanol plant designs.

Information and Analysis System Stages of Family Welfare in District Balong

Directory of Open Access Journals (Sweden)

Eka Arynda Ayu

2017-05-01

Full Text Available Badan Kependudukan dan Keluarga Berencana Nasional (BKKBN is a family that formed due to legal marriage, is able to meet the needs of the spiritual and the material that is decent, devoted to God Almighty, have a relationship that is harmonious and balanced between members and between families with the community and the environment. Every year the government to collect data on the status of a prosperous family stage where the purpose of the data collection is in the framework of development and poverty alleviation programs. Data collection process in the District Balong is still done manually so that the risk of error in determining the status of a family stage could happen. Information and analysis system of status stages of family welfare is designed to make web-based officers in the input data and determine the status of a prosperous family stages based on selected indicators of the sheet R/1/KS. Sample of data from Bulukidul village and sub-district village of Balong Ngraket 2014. Results of the system in the form of data reports the results of process steps and the results can be viewed in graphical form. Comparison chart to show the status of the highest percentage of poor welfare families stages. Instead lowest percentage shows the stages of a prosperous family able or rich. 

Alkaline pretreatment of Mexican pine residues for bioethanol ...

African Journals Online (AJOL)

Alkaline pretreatment of Mexican pine residues for bioethanol production. ... Keywords: Lignocellulosic biomass, alkaline pretreatment, enzymatic hydrolysis, fermentable sugars, fermentation. African Journal of Biotechnology Vol. 12(31), pp.

Hydrodynamic cavitation as a strategy to enhance the efficiency of lignocellulosic biomass pretreatment.

Science.gov (United States)

Terán Hilares, Ruly; Ramos, Lucas; da Silva, Silvio Silvério; Dragone, Giuliano; Mussatto, Solange I; Santos, Júlio César Dos

2018-06-01

Hydrodynamic cavitation (HC) is a process technology with potential for application in different areas including environmental, food processing, and biofuels production. Although HC is an undesirable phenomenon for hydraulic equipment, the net energy released during this process is enough to accelerate certain chemical reactions. The application of cavitation energy to enhance the efficiency of lignocellulosic biomass pretreatment is an interesting strategy proposed for integration in biorefineries for the production of bio-based products. Moreover, the use of an HC-assisted process was demonstrated as an attractive alternative when compared to other conventional pretreatment technologies. This is not only due to high pretreatment efficiency resulting in high enzymatic digestibility of carbohydrate fraction, but also, by its high energy efficiency, simple configuration, and construction of systems, besides the possibility of using on the large scale. This paper gives an overview regarding HC technology and its potential for application on the pretreatment of lignocellulosic biomass. The parameters affecting this process and the perspectives for future developments in this area are also presented and discussed.

A Sequential Combination of Laccase Pretreatment and Enzymatic Hydrolysis for Glucose Production from Furfural Residues

Directory of Open Access Journals (Sweden)

Hailong Yu

2014-06-01

Full Text Available Furfural residues (FRs were pretreated with laccase or a laccase-mediator (1-hydroxybenzotriazole, HBT system to produce fermentable sugar for bioethanol production. Compared to laccase-only pretreatment, laccase-mediator pretreatment dissolved more lignin. Approximately 10.5% of the initially present lignin was removed when FRs were treated with a laccase loading of 100 U/g of dry substrate in 1% (w/w HBT at 48 °C for 24 h in an acetate buffer (pH 4.8. The enzymatic saccharification process was carried out by a combined laccase or laccase-mediator pretreatment without washing of the treated solids. The results showed that active laccase had a negative effect on the rate and yield of enzymatic hydrolysis. Laccase-oxidized HBT seriously reduced glucose yield. However, non-oxidized HBT increased glucose yield when laccase was deactivated at 121 °C for 20 min prior to enzymatic hydrolysis. The highest glucose yield, 80.9%, was obtained from the substrate pretreated with 100 U/g of dry substrate laccase and 1% (w/w HBT at 48 °C for 24 h in an acetate buffer (pH 4.8. Furthermore, the structures of FRs before and after laccase-mediator pretreatment were characterized by scanning electron microscopy (SEM and Fourier Transform Infrared spectroscopy (FT-IR.

Influence of capacity- and time-constrained intermediate storage in two-stage food production systems

DEFF Research Database (Denmark)

Akkerman, Renzo; van Donk, Dirk Pieter; Gaalman, Gerard

2007-01-01

In food processing, two-stage production systems with a batch processor in the first stage and packaging lines in the second stage are common and mostly separated by capacity- and time-constrained intermediate storage. This combination of constraints is common in practice, but the literature hardly...... of systems like this. Contrary to the common sense in operations management, the LPT rule is able to maximize the total production volume per day. Furthermore, we show that adding one tank has considerable effects. Finally, we conclude that the optimal setup frequency for batches in the first stage...... pays any attention to this. In this paper, we show how various capacity and time constraints influence the performance of a specific two-stage system. We study the effects of several basic scheduling and sequencing rules in the presence of these constraints in order to learn the characteristics...

Value of five-stage prognostic system in predicting short-term outcome of patients with liver cirrhosis

Directory of Open Access Journals (Sweden)

TIAN Yan

2015-03-01

Full Text Available ObjectiveTo evaluate the clinical value of five-stage prognostic system in predicting the short-term outcome of patients with liver cirrhosis, and to compare it with the Child-Turcotte-Pugh (CTP and Model of End-Stage Liver Disease (MELD scores. MethodsTwo hundred and one hospitalized patients with liver cirrhosis in the Department of Gastroenterology in the First Affiliated Hospital of Anhui Medical University from January 2011 to January 2014 were enrolled in the study and followed up for at least six months. Patients were classified accorded to the five-stage prognostic system, and the mortality rate in each stage was measured. The receiver operating characteristic (ROC curve and the area under the ROC curve (AUC were used to assess the accuracy of the five-stage prognostic system in predicting the short-term death risk of cirrhotic patients, which was then compared with the CTP and MELD scores. Categorical data were analyzed by chi-square test. Comparison of AUC was made by normal distribution Z test. Spearman′s correlation analysis was used to investigate the correlation of the five-stage prognostic system with the CTP and MELD scores. ResultsThe study used the admission time as the starting point and the death of patients or study termination time as the endpoint. Among the 201 patients, 50 (24.9% died within six months. Based on the five-stage prognostic system, the mortality rates for stages 1 to 5 were 0(0/11, 0（0/18, 4.2%（2/48, 16.3% (7/43, and 50.6%（41/81, respectively. In patients with decompensated cirrhosis (stages 3, 4, and 5, the mortality increased with stage, and the differences in mortality between patients in stages 3 and 4, 3 and 5, and 4 and 5 were all significant (χ2=3.89, 35.33, and 13.96, respectively; P=0.049, 0.000, and 0.049, respectively. The AUC for the five-stage prognostic system, five-stage prognostic system combined with CTP and MELD score, and CTP score were 0820, 0.915, 0.888, and 0

Hydrodynamic cavitation as a novel pretreatment approach for bioethanol production from reed.

Science.gov (United States)

Kim, Ilgook; Lee, Ilgyu; Jeon, Seok Hwan; Hwang, Taewoon; Han, Jong-In

2015-09-01

In this study, hydrodynamic cavitation (HC) was employed as a physical means to improve alkaline pretreatment of reed. The HC-assisted alkaline pretreatment was undertaken to evaluate the influence of NaOH concentration (1-5%), solid-to-liquid ratio (5-15%), and reaction time (20-60 min) on glucose yield. The optimal condition was found to be 3.0% NaOH at solid-to-liquid (S/L) ratio of 11.8% for 41.1 min, which resulted in the maximum glucose yield of 326.5 g/kg biomass. Furthermore, simultaneous saccharification and fermentation (SSF) was conducted to assess the ethanol production. An ethanol concentration of 25.9 g/L and ethanol yield of 90% were achieved using batch SSF. These results clearly demonstrated HC system can be indeed a promising pretreatment tool for lignocellulosic bioethanol production. Copyright © 2015 Elsevier Ltd. All rights reserved.

MRI or CT for pretreatment staging and radiotherapy planning for radiochemotherapy in distal rectal cancer. Radiologists point

International Nuclear Information System (INIS)

Vloka, M.; Kirkova, G.

2013-01-01

Full text: Introduction: In the recent years, the therapeutic approach to rectal cancer changed dramatically. Implementation of a common mesorectal excision and preoperative radiotherapy has become a standard procedure. Noninvasive imaging methods have become basic and leading methods in the process of pre-therapy staging and rectal cancer radiotherapy planning. What you will learn : Following the recommendations of the 2013 ESGAR EURECCA 2012 we will present: a comparative data about the place and role of MRI and CT in the algorithm for low rectal carcinoma staging ; a standard MRI protocol for low rectum carcinoma staging as well as the questions concerning the image interpretation that the radiologist needs to answer. Discussion : Based on the European rules and consensus in the standard protocols implementation of in conducting MRI in rectal cancer, we have the opportunity for preoperative staging of the tumor and hence for proper treatment. The high spatial and tissue resolution of MRI allows carcinoma’s visualization at the depth infiltration of the wall of rectum, distance from mesorectal fascia, involvement of anorectal sphincter, pelvic floor and adjacent bodies, involvement of the venous plexus and the metastatic pararectal lymph nodes presence. Additional performed lung, abdomen and pelvis CT (MDCT) has limited chance for tumor staging, but it serves for distant metastases detection. Conclusion: MRI is the main method for T and N staging and re-staging of low carcinoma of the rectum. MDCT is used for determination of the N stages of the disease

Tank Focus Area Pretreatment Program. FY 1995 Program Management Plan

International Nuclear Information System (INIS)

Morrison, M.I.; McGinnis, C.P.; Wilkenson, W.T.; Hunt, R.D.

1995-02-01

This program management plan (PMP) describes the FY 1995 project plans for the Pretreatment Program of the Tank Focus Area. The Tank Focus Area is one of five areas of environmental concerns originally identified by the Deputy Assistant Secretary for Technology Development (EM-50). Projects in the Tank Focus Area relate to the remediation of liquid waste stored in underground storage tanks at various US Department of Energy sites. The Pretreatment Program is an organizational unit performing work within the Tank Focus Area. The function of the Pretreatment Program is to develop, test, evaluate, and demonstrate new technologies, with emphasis on separations. The 11 Pretreatment Program projects for FY 1995 are (1) Cesium Extraction Testing, (2) Comprehensive Supernate Treatment, (3) Hot Cell Studies, (4) Cesium Removal Demonstration, (5) Out-of-Tank Evaporator Demonstration, (6) Crossflow Filtration, (7) Technical Interchange with CEA, (8) TRUEX Applications, (9) NAC/NAG Process Studies (conducted at Oak Ridge National Laboratory), (10) NAC/NAG Process and Waste Form Studies (conducted at Florida International University), and (11) Program Management. Section 2 of this PMP contains a separate subsection for each FY 1995 project. A brief description of the project, a schedule of major milestones, and a breakdown of costs are provided for each project. The PMP also contains sections that describe the project controls that are in place. Quality assurance, document control, the project management system, and the management organization are described in these sections

Pretreatment data is highly predictive of liver chemistry signals in clinical trials.

Science.gov (United States)

Cai, Zhaohui; Bresell, Anders; Steinberg, Mark H; Silberg, Debra G; Furlong, Stephen T

2012-01-01

The goal of this retrospective analysis was to assess how well predictive models could determine which patients would develop liver chemistry signals during clinical trials based on their pretreatment (baseline) information. Based on data from 24 late-stage clinical trials, classification models were developed to predict liver chemistry outcomes using baseline information, which included demographics, medical history, concomitant medications, and baseline laboratory results. Predictive models using baseline data predicted which patients would develop liver signals during the trials with average validation accuracy around 80%. Baseline levels of individual liver chemistry tests were most important for predicting their own elevations during the trials. High bilirubin levels at baseline were not uncommon and were associated with a high risk of developing biochemical Hy's law cases. Baseline γ-glutamyltransferase (GGT) level appeared to have some predictive value, but did not increase predictability beyond using established liver chemistry tests. It is possible to predict which patients are at a higher risk of developing liver chemistry signals using pretreatment (baseline) data. Derived knowledge from such predictions may allow proactive and targeted risk management, and the type of analysis described here could help determine whether new biomarkers offer improved performance over established ones.

Improving biogas production from microalgae by enzymatic pretreatment.

Science.gov (United States)

Passos, Fabiana; Hom-Diaz, Andrea; Blanquez, Paqui; Vicent, Teresa; Ferrer, Ivet

2016-01-01

In this study, enzymatic pretreatment of microalgal biomass was investigated under different conditions and evaluated using biochemical methane potential (BMP) tests. Cellulase, glucohydrolase and an enzyme mix composed of cellulase, glucohydrolase and xylanase were selected based on the microalgae cell wall composition (cellulose, hemicellulose, pectin and glycoprotein). All of them increased organic matter solubilisation, obtaining high values already after 6h of pretreatment with an enzyme dose of 1% for cellulase and the enzyme mix. BMP tests with pretreated microalgae showed a methane yield increase of 8 and 15% for cellulase and the enzyme mix, respectively. Prospective research should evaluate enzymatic pretreatments in continuous anaerobic reactors so as to estimate the energy balance and economic cost of the process. Copyright © 2015 Elsevier Ltd. All rights reserved.

Testing of alkaline and enzymatic hydrolysis pretreatments for fat particles in slaughterhouse wastewater.

Science.gov (United States)

Masse, L; Kennedy, K J; Chou, S

2001-04-01

Four pretreatments to hydrolyse and/or reduce the size of fat particles in slaughterhouse wastewater (SHW) were tested: sodium hydroxide and three lipases of plant, bacterial and animal (pancreatic) origin. Hydrolysing agents and SHW containing between 2.5 and 3 g/l of fat particles were mixed at room temperature for 4 h. Additions of 5-400 meq NaOH/l did not increase soluble COD (SCOD) in SHW, but the average particle size was reduced to 73% +/- 7% of the initial average particle size (D(in)) at NaOH concentrations ranging from 150 to 300 meq/l. Pretreatment with pancreatic lipase PL-250 reduced the average particle size to a maximum of 60% +/- 3% of D(in). As D(in) was decreased from 359 to 68 microns, the enzyme concentration required to obtain the maximum particle size reduction increased from 200 to 1000 mg/l. A 4-h pretreatment with PL-250 also increased the free long-chain fatty acid (LCFA) concentration to a maximum of 15.5 mg/l, indicating some solubilization of the pork fat particles in SHW. SCOD was not significantly increased by the pretreatment, but SCOD was not found to be a good indicator of enzymatic lipolysis because of enzyme adsorption on the fat particle surface. Pancreatic lipase appeared more efficient with beef fat than pork fat, possibly because beef fat contains less polyunsaturated fatty acids than pork fat. The bacterial lipase LG-1000 was also efficient in reducing average fat particle size, but high doses (> 1000 mg/l) were required to obtain a significant reduction after 4 h of pretreatment. SCOD was not increased by pretreatment with LG-1000. No particle size reduction or changes in SCOD were noted after 4 h of pretreatment with the plant lipase EcoSystem Plus. It was concluded that PL-250 was the best pretreatment to hydrolyse fat particles in SHW. However, its impact on the efficiency of a downstream anaerobic digestion process remains to be tested.

Alkaline/peracetic acid as a pretreatment of lignocellulosic biomass for ethanol fuel production

Science.gov (United States)

Teixeira, Lincoln Cambraia

Peracetic acid is a lignin oxidation pretreatment with low energy input by which biomass can be treated in a silo type system for improving enzymatic digestibility of lignocellulosic materials for ethanol production. Experimentally, ground hybrid poplar wood and sugar cane bagasse are placed in plastic bags and a peracetic acid solution is added to the biomass in different concentrations based on oven-dry biomass. The ratio of solution to biomass is 6:1; after initial mixing of the resulting paste, a seven-day storage period at about 20°C is used in this study. As a complementary method, a series of pre-pretreatments using stoichiometric amounts of sodium hydroxide and ammonium hydroxide based on 4-methyl-glucuronic acid and acetyl content in the biomass is been performed before addition of peracetic acid. The alkaline solutions are added to the biomass in a ratio of 14:1 solution to biomass; the slurry is mixed for 24 hours at ambient temperature. The above procedures give high xylan content substrates. Consequently, xylanase/beta-glucosidase combinations are more effective than cellulase preparations in hydrolyzing these materials. The pretreatment effectiveness is evaluated using standard enzymatic hydrolysis and simultaneous saccharification and cofermentation (SSCF) procedures. Hybrid poplar wood pretreated with 15 and 21% peracetic acid based on oven-dry weight of wood gives glucan conversion yields of 76.5 and 98.3%, respectively. Sugar cane bagasse pretreated with the same loadings gives corresponding yields of 85.9 and 93.1%. Raw wood and raw bagasse give corresponding yields of 6.8 and 28.8%, respectively. The combined 6% NaOH/15% peracetic acid pretreatments increase the glucan conversion yields from 76.5 to 100.0% for hybrid poplar wood and from 85.9 to 97.6% for sugar cane bagasse. Respective ethanol yields of 92.8 and 91.9% are obtained from 6% NaOH/15% peracetic acid pretreated materials using recombinant Zymomonas mobilis CP4/pZB5. Peracetic acid

Optimization of a Two Stage Pulse Tube Refrigerator for the Integrated Current Lead System

Science.gov (United States)

Maekawa, R.; Matsubara, Y.; Okada, A.; Takami, S.; Konno, M.; Tomioka, A.; Imayoshi, T.; Hayashi, H.; Mito, T.

2008-03-01

Implementation of a conventional current lead with a pulse tube refrigerator has been validated to be working as an Integrated Current Lead (ICL) system for the Superconducting Magnetic Energy Storage (SMES). Realization of the system is primarily accounted for the flexibility of a pulse tube refrigerator, which does not posses any mechanical piston and/or displacer. As for an ultimate version of the ICL system, a High Temperature Superconducting (HTS) lead links a superconducting coil with a conventional copper lead. To ensure the minimization of heat loads to the superconducting coil, a pulse tube refrigerator has been upgraded to have a second cooling stage. This arrangement reduces not only the heat loads to the superconducting coil but also the operating cost for a SMES system. A prototype two-stage pulse tube refrigerator, series connected arrangement, was designed and fabricated to satisfy the requirements for the ICL system. Operation of the first stage refrigerator is a four-valve mode, while the second stage utilizes a double inlet configuration to ensure its confined geometry. The paper discusses the optimization of second stage cooling to validate the conceptual design

Survey of Lignin-Structure Changes and Depolymerization during Ionic Liquid Pretreatment

Energy Technology Data Exchange (ETDEWEB)

Dutta, Tanmoy; Isern, Nancy G.; Sun, Jian; Wang, Eileen; Hull, Sarah; Cort, John R.; Simmons, Blake A.; Singh, Seema

2017-09-26

A detailed study of chemical changes in lignin structure during the ionic liquid (IL) pretreatment process is not only pivotal for understanding and overcoming biomass recalcitrance during IL pretreatment, but also is necessary for designing new routes for lignin valorization. Chemical changes in lignin were systematically studied as a function of pretreatment temperature, time and type of IL used. Kraft lignin was used as the lignin source and common pretreatment conditions were employed using three different ILs of varying chemical structure in terms of acidic or basic character. The chemical changes in the lignin structure due to IL pretreatment processes were monitored using 1H-13C HSQC NMR, 31P NMR, elemental analysis, GPC, FT-IR, and the depolymerized products were analyzed using GC-MS. Although pretreatment in acidic IL, triethylammonium hydrogensulfate ([TEA][HSO4]) results in maximum decrease in β-aryl ether bond, maximum dehydration and recondensation pathways were also evident, with the net process showing a minimum decrease in the molecular weight of regenerated lignin. However, 1-ethyl-3-methylimidazolium acetate ([C2C1Im][OAc]) pretreatment yields a smaller decrease in the β-aryl ether content along with minimum evidence of recondensation, resulting in the maximum decrease in the molecular weight. Cholinium lysinate ([Ch][Lys]) pretreatment shows an intermediate result, with moderate depolymerization, dehydration and recondensation observed. The depolymerization products after IL pretreatment are found to be a function of the pretreatment temperature and the specific chemical nature of the IL used. At higher pretreatment temperature, [Ch][Lys] pretreatment yields guaiacol, [TEA][HSO4] yields guaiacylacetone, and [C2C1Im][OAc] yields both guaiacol and guaiacylacetone as major products. These results clearly indicate that the changes in lignin structure as well as the depolymerized product profile depend on the pretreatment conditions and the nature

Multi-stage fuzzy PID power system automatic generation controller in deregulated environments

International Nuclear Information System (INIS)

Shayeghi, H.; Shayanfar, H.A.; Jalili, A.

2006-01-01

In this paper, a multi-stage fuzzy proportional integral derivative (PID) type controller is proposed to solve the automatic generation control (AGC) problem in a deregulated power system that operates under deregulation based on the bilateral policy scheme. In each control area, the effects of the possible contracts are treated as a set of new input signals in a modified traditional dynamical model. The multi-stage controller uses the fuzzy switch to blend a proportional derivative (PD) fuzzy logic controller with an integral fuzzy logic input. The proposed controller operates on fuzzy values passing the consequence of a prior stage on to the next stage as fact. The salient advantage of this strategy is its high insensitivity to large load changes and disturbances in the presence of plant parameter variations and system nonlinearities. This newly developed strategy leads to a flexible controller with simple structure that is easy to implement, and therefore, it can be useful for the real world power systems. The proposed method is tested on a three area power system with different contracted scenarios under various operating conditions. The results of the proposed controller are compared with those of the classical fuzzy PID type controller and classical PID controller through some performance indices to illustrate its robust performance

Biorefining of wheat straw: accounting for the distribution of mineral elements in pretreated biomass by an extended pretreatment – severity equation

DEFF Research Database (Denmark)

Le, Duy Michael; Sørensen, Hanne Risbjerg; Knudsen, Niels Ole

2014-01-01

Background: Mineral elements present in lignocellulosic biomass feedstocks may accumulate in biorefinery process streams and cause technological problems, or alternatively can be reaped for value addition. A better understanding of the distribution of minerals in biomass in response to pretreatment...... factors is therefore important in relation to development of new biorefinery processes. The objective of the present study was to examine the levels of mineral elements in pretreated wheat straw in response to systematic variations in the hydrothermal pretreatment parameters (pH, temperature......) Silicon, iron, copper, aluminum correlated with lignin and cellulose levels, but the levels of these constituents showed no severity-dependent trends. For the first group, an expanded pretreatment-severity equation, containing a specific factor for each constituent, accounting for variability due...

Pretreatment of Reed by Wet Oxidation and Subsequent Utilization of the Pretreated Fibers for Ethanol Production

DEFF Research Database (Denmark)

Szijarto, Nora; Kádár, Zsófia; Varga, Eniko

2009-01-01

lignocelluloses usually do. In the present study, wet oxidation was investigated as the pretreatment method to enhance the enzymatic digestibility of reed cellulose to soluble sugars and thus improve the convertibility of reed to ethanol. The most effective treatment increased the digestibility of reed cellulose...... of cellulose to glucose was 82.4%. Simultaneous saccharification and fermentation of pretreated solids resulted in a final ethanol concentration as high as 8.7 g/L, yielding 73% of the theoretical....

Making lignin accessible for anaerobic digestion by wet-explosion pretreatment

DEFF Research Database (Denmark)

Ahring, Birgitte Kiær; Biswas, Rajib; Ahamed, Aftab

2015-01-01

of lignin during anaerobic digestion processes. The pretreatment of feedlot manure was performed in a 10 L reactor at 170 C for 25 min using 4 bars oxygen and the material was fed to a continuous stirred tank reactor operated at 55 C for anaerobic digestion. Methane yield of untreated and pretreated...... material was 70 ± 27 and 320 ± 36 L/kg-VS/day, respectively, or 4.5 times higher yield as a result of the pretreatment. Aliphatic acids formed during the pretreatment were utilized by microbes. 44.4% lignin in pretreated material was actually converted in the anaerobic digestion process compared to 12...

Computer simulation of a staging system for a theta-pinch reactor (RTPR)

International Nuclear Information System (INIS)

Crnkovich, P.G.

1976-02-01

To reduce excessive energy requirements for the implosion heating system of a theta-pinch reactor, two staging methods, the brute force and bucking field options, were proposed. A Marshall coil and a segmented coil were also considered. Calculations involved in coding these coil designs and staging options into a PL/I subprogram are described. A marked savings in the energy required for the IH system is realized with the bucking option and others

Prognostic factors in Hodgkin's disease stage III with special reference to tumour burden

DEFF Research Database (Denmark)

Specht, L.; Nissen, N.I.

1988-01-01

of lymphographically involved regions), histologic subtype, B-symptoms, number of involved regions, mediastinal involvement, pretreatment ESR, sex, age, laparotomy, and substage were examined in multivariate analysis. With regard to disease-free survival, total tumour burden (intraabdominal and peripheral...... regarding early stage disease to the effect that tumour burden is the single most important prognostic factor in Hodgkin's disease....

Effects of Pretreatment Methods on Electrodes and SOFC Performance

Directory of Open Access Journals (Sweden)

Guo-Bin Jung

2014-06-01

Full Text Available Commercially available tapes (anode, electrolyte and paste (cathode were choosen to prepare anode-supported cells for solid oxide fuel cell applications. For both anode-supported cells or electrolyte-supported cells, the anode needs pretreatment to reduce NiO/YSZ to Ni/YSZ to increase its conductivity as well as its catalytic characteristics. In this study, the effects of different pretreatments (open-circuit, closed-circuit on cathode and anodes as well as SOFC performance are investigated. To investigate the influence of closed-circuit pretreatment on the NiO/YSZ anode alone, a Pt cathode is utilized as reference for comparison with the LSM cathode. The characterization of the electrical resistance, AC impedance, and SOFC performance of the resulting electrodes and/or anode-supported cell were carried out. It’s found that the influence of open-circuit pretreatment on the LSM cathode is limited. However, the influence of closed-circuit pretreatment on both the LSM cathode and NiO/YSZ anode and the resulting SOFC performance is profound. The effect of closed-circuit pretreatment on the NiO/YSZ anode is attributed to its change of electronic/pore structure as well as catalytic characteristics. With closed-circuit pretreatment, the SOFC performance improved greatly from the change of LSM cathode (and Pt reference compared to the Ni/YSZ anode.

Pre-treatment risk stratification of prostate cancer patients: A critical review.

Science.gov (United States)

Rodrigues, George; Warde, Padraig; Pickles, Tom; Crook, Juanita; Brundage, Michael; Souhami, Luis; Lukka, Himu

2012-04-01

The use of accepted prostate cancer risk stratification groups based on prostate-specific antigen, T stage and Gleason score assists in therapeutic treatment decision-making, clinical trial design and outcome reporting. The utility of integrating novel prognostic factors into an updated risk stratification schema is an area of current debate. The purpose of this work is to critically review the available literature on novel pre-treatment prognostic factors and alternative prostate cancer risk stratification schema to assess the feasibility and need for changes to existing risk stratification systems. A systematic literature search was conducted to identify original research publications and review articles on prognostic factors and risk stratification in prostate cancer. Search terms included risk stratification, risk assessment, prostate cancer or neoplasms, and prognostic factors. Abstracted information was assessed to draw conclusions regarding the potential utility of changes to existing risk stratification schema. The critical review identified three specific clinically relevant potential changes to the most commonly used three-group risk stratification system: (1) the creation of a very-low risk category; (2) the splitting of intermediate-risk into a low- and high-intermediate risk groups; and (3) the clarification of the interface between intermediate- and high-risk disease. Novel pathological factors regarding high-grade cancer, subtypes of Gleason score 7 and percentage biopsy cores positive were also identified as potentially important risk-stratification factors. Multiple studies of prognostic factors have been performed to create currently utilized prostate cancer risk stratification systems. We propose potential changes to existing systems.

Pretreatment Dysphagia in Esophageal Cancer Patients May Eliminate the Need for Staging by Endoscopic Ultrasonography.

Science.gov (United States)

Ripley, R Taylor; Sarkaria, Inderpal S; Grosser, Rachel; Sima, Camelia S; Bains, Manjit S; Jones, David R; Adusumilli, Prasad S; Huang, James; Finley, David J; Rusch, Valerie W; Rizk, Nabil P

2016-01-01

Neoadjuvant therapy is commonly administered to patients with localized disease who have T3-4 esophageal disease as staged by endoscopic ultrasound (EUS). Previously, we noted that patients who present with dysphagia have a higher EUS T stage. We hypothesized that the presence of dysphagia is predictive of EUS T3-4 disease and that staging EUS could be forgone for esophageal cancer patients with dysphagia. We performed a prospective, intent-to-treat, single-cohort study in which patients with potentially resectable esophageal cancer completed a standardized four-tier dysphagia score survey. EUS was performed as part of our standard evaluation. To determine whether the presence of dysphagia predicted EUS T3-4 disease, the dysphagia score was compared with EUS T stage. The study enrolled 114 consecutive patients between August 2012 and February 2014: 77% (88 of 114) received neoadjuvant therapy, 18% (20 of 114) did not, and 5% (6 of 114) pursued treatment elsewhere. In total, 70% (80 of 114) underwent esophagectomy; of these, 54% (61 of 114) had dysphagia and 46% (53 of 114) did not. Dysphagia scores were 66% (40 of 61) grade 1, 25% (15 of 61) grade 2, and 10% (6 of 61) grade 3 to 4. Among patients with dysphagia, 89% (54 of 61) had T3-4 disease by EUS; among those without dysphagia, only 53% (28 of 53) had T3-4 disease by EUS (p < 0.001). The presence of dysphagia in patients with esophageal cancer was highly predictive of T3-4 disease by EUS. On the basis of this finding, approximately 50% of patients currently undergoing staging EUS at our institution could potentially forgo EUS before neoadjuvant therapy. Patients without dysphagia, however, should still undergo EUS. Copyright © 2016 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Development and validation of a surgical-pathologic staging and scoring system for cervical cancer.

Science.gov (United States)

Li, Shuang; Li, Xiong; Zhang, Yuan; Zhou, Hang; Tang, Fangxu; Jia, Yao; Hu, Ting; Sun, Haiying; Yang, Ru; Chen, Yile; Cheng, Xiaodong; Lv, Weiguo; Wu, Li; Zhou, Jin; Wang, Shaoshuai; Huang, Kecheng; Wang, Lin; Yao, Yuan; Yang, Qifeng; Yang, Xingsheng; Zhang, Qinghua; Han, Xiaobing; Lin, Zhongqiu; Xing, Hui; Qu, Pengpeng; Cai, Hongbing; Song, Xiaojie; Tian, Xiaoyu; Shen, Jian; Xi, Ling; Li, Kezhen; Deng, Dongrui; Wang, Hui; Wang, Changyu; Wu, Mingfu; Zhu, Tao; Chen, Gang; Gao, Qinglei; Wang, Shixuan; Hu, Junbo; Kong, Beihua; Xie, Xing; Ma, Ding

2016-04-12

Most cervical cancer patients worldwide receive surgical treatments, and yet the current International Federation of Gynecology and Obstetrics (FIGO) staging system do not consider surgical-pathologic data. We propose a more comprehensive and prognostically valuable surgical-pathologic staging and scoring system (SPSs). Records from 4,220 eligible cervical cancer cases (Cohort 1) were screened for surgical-pathologic risk factors. We constructed a surgical-pathologic staging and SPSs, which was subsequently validated in a prospective study of 1,104 cervical cancer patients (Cohort 2). In Cohort 1, seven independent risk factors were associated with patient outcome: lymph node metastasis (LNM), parametrial involvement, histological type, grade, tumor size, stromal invasion, and lymph-vascular space invasion (LVSI). The FIGO staging system was revised and expanded into a surgical-pathologic staging system by including additional criteria of LNM, stromal invasion, and LVSI. LNM was subdivided into three categories based on number and location of metastases. Inclusion of all seven prognostic risk factors improves practical applicability. Patients were stratified into three SPSs risk categories: zero-, low-, and high-score with scores of 0, 1 to 3, and ≥4 (P=1.08E-45; P=6.15E-55). In Cohort 2, 5-year overall survival (OS) and disease-free survival (DFS) outcomes decreased with increased SPSs scores (P=9.04E-15; P=3.23E-16), validating the approach. Surgical-pathologic staging and SPSs show greater homogeneity and discriminatory utility than FIGO staging. Surgical-pathologic staging and SPSs improve characterization of tumor severity and disease invasion, which may more accurately predict outcome and guide postoperative therapy.

Fill Rates of Single-Stage and Multistage Supply Systems

OpenAIRE

Matthew J. Sobel

2004-01-01

A supply system's fill rate is the fraction of demand that is met from on-hand inventory. This paper presents formulas for the fill rate of periodic review supply systems that use base-stock-level policies. The first part of the paper contains fill-rate formulas for a single-stage system and general distributions of demand. When demand is normally distributed, an exact expression uses only the standard normal distribution and density functions, and a good approximation uses only the standard ...

Enhanced thermophilic fermentative hydrogen production from cassava stillage by chemical pretreatments.

Science.gov (United States)

Wang, Wen; Luo, Gang; Xie, Li; Zhou, Qi

2013-01-01

Acid and alkaline pretreatments for enhanced hydrogen production from cassava stillage were investigated in the present study. The result showed that acid pretreatment was suitable for enhancement of soluble carbohydrate while alkaline pretreatment stimulated more soluble total organic carbon production from cassava stillage. Acid pretreatment thereby has higher capacity to promote hydrogen production compared with alkaline pretreatment. Effects of pretreatment temperature, time and acid concentration on hydrogen production were also revealed by response surface methodology. The results showed that the increase of all factors increased the soluble carbohydrate production, whereas hydrogen production was inhibited when the factors exceeded their optimal values. The optimal conditions for hydrogen production were pretreatment temperature 89.5 °C, concentration 1.4% and time 69 min for the highest hydrogen production of 434 mL, 67% higher than raw cassava stillage.

Development and testing of a de novo clinical staging system for podoconiosis (endemic non-filarial elephantiasis).

Science.gov (United States)

Tekola, Fasil; Ayele, Zewdu; Mariam, Dereje Haile; Fuller, Claire; Davey, Gail

2008-10-01

To develop and test a robust clinical staging system for podoconiosis, a geochemical disease in individuals exposed to red clay soil. We adapted the Dreyer system for staging filarial lymphoedema and tested it in four re-iterative field tests conducted in an area of high-podoconiosis prevalence in Southern Ethiopia. The system has five stages according to proximal spread of disease and presence of dermal nodules, ridges and bands. We measured the 1-week repeatability and the inter-observer agreement of the final staging system. The five-stage system is readily understood by community workers with little health training. Kappa for 1-week repeatability was 0.88 (95% CI 0.80-0.96), for agreement between health professionals was 0.71 (95% CI 0.60-0.82), while that between health professionals and community podoconiosis agents without formal health training averaged 0.64 (95% CI 0.52-0.78). This simple staging system with good inter-observer agreement and repeatability can assist in the management and further study of podoconiosis.

Understanding of alkaline pretreatment parameters for corn stover enzymatic saccharification

Directory of Open Access Journals (Sweden)

Chen Ye

2013-01-01

Full Text Available Abstract Background Previous research on alkaline pretreatment has mainly focused on optimization of the process parameters to improve substrate digestibility. To achieve satisfactory sugar yield, extremely high chemical loading and enzyme dosages were typically used. Relatively little attention has been paid to reduction of chemical consumption and process waste management, which has proven to be an indispensable component of the bio-refineries. To indicate alkali strength, both alkali concentration in pretreatment solution (g alkali/g pretreatment liquor or g alkali/L pretreatment liquor and alkali loading based on biomass solids (g alkali/g dry biomass have been widely used. The dual approaches make it difficult to compare the chemical consumption in different process scenarios while evaluating the cost effectiveness of this pretreatment technology. The current work addresses these issues through pretreatment of corn stover at various combinations of pretreatment conditions. Enzymatic hydrolysis with different enzyme blends was subsequently performed to identify the effects of pretreatment parameters on substrate digestibility as well as process operational and capital costs. Results The results showed that sodium hydroxide loading is the most dominant variable for enzymatic digestibility. To reach 70% glucan conversion while avoiding extensive degradation of hemicellulose, approximately 0.08 g NaOH/g corn stover was required. It was also concluded that alkali loading based on total solids (g NaOH/g dry biomass governs the pretreatment efficiency. Supplementing cellulase with accessory enzymes such as α-arabinofuranosidase and β-xylosidase significantly improved the conversion of the hemicellulose by 6–17%. Conclusions The current work presents the impact of alkaline pretreatment parameters on the enzymatic hydrolysis of corn stover as well as the process operational and capital investment costs. The high chemical consumption for alkaline

Pretreatment status report on the identification and evaluation of alternative processes

International Nuclear Information System (INIS)

Sutherland, D.G.; Brothers, A.J.; Beary, M.M.; Nicholson, G.A.

1993-09-01

The purpose of this report is to support the development and demonstration of a pretreatment system that will (1) destroy organic materials and ferrocyanide in tank wastes so that the wastes can be stored safely, (2) separate the high-activity and low-activity fractions, (3) remove radionuclides and remove or destroy hazardous chemicals in LLW as necessary to meet waste form feed requirements, (4) support development and demonstration of vitrification technology by providing representative feeds to the bench-scale glass melter, (5) support full-scale HLW vitrification operations, including near-term operation, by providing feed that meets specifications, and (6) design and develop pretreatment processes that accomplish the above objectives and ensure compliance with environmental regulations. This report is a presentation of candidate technologies for pretreatment of Hanford Site tank waste. Included are descriptions of studies by the Pacific Northwest Laboratory of Battelle Memorial Institute; Science Applications International Corporation, an independent consultant; BNFL, Inc. representing British technologies; Numatec, representing French technologies; and brief accounts of other relevant activities

Impact of pretreatment on colour and texture of watermelon rind

Science.gov (United States)

Athmaselvi, K.; Alagusundaram, K.; Kavitha, C.; Arumuganathan, T.

2012-07-01

The effect of osmotic dehydration pretreatment on water loss, solid gain, colour and textural change was investigated. Watermelon rind 1 x 1 cm size was immersed in sucrose solution of 40, 50 and 60° Brix after pretreatment with microwave and conventional boiling in water for 1, 3, and 5 min, respectively. Water loss and solid gain increased with the time of cooking and sugar concentration. Microwave pretreated samples showed higher water loss and solid gain. Increase in the time of cooking decreased the brightness of all the samples. Microwave pretreated samples showed higher `b' values than conventionally pretreated ones. There was no significant difference (P≤0.05) in texture profile analysis parameters except for hardness. Hardness decreased with increase in time of cooking and sugar concentration. Second order regression model was developed for water loss and solid gain of microwave and conventional pretreated watermelon rind.

Biomass pretreatment affects Ustilago maydis in producing itaconic acid

Directory of Open Access Journals (Sweden)

Klement Tobias

2012-04-01

Full Text Available Abstract Background In the last years, the biotechnological production of platform chemicals for fuel components has become a major focus of interest. Although ligno-cellulosic material is considered as suitable feedstock, the almost inevitable pretreatment of this recalcitrant material may interfere with the subsequent fermentation steps. In this study, the fungus Ustilago maydis was used to produce itaconic acid as platform chemical for the synthesis of potential biofuels such as 3-methyltetrahydrofuran. No studies, however, have investigated how pretreatment of ligno-cellulosic biomass precisely influences the subsequent fermentation by U. maydis. Thus, this current study aims to first characterize U. maydis in shake flasks and then to evaluate the influence of three exemplary pretreatment methods on the cultivation and itaconic acid production of this fungus. Cellulose enzymatically hydrolysed in seawater and salt-assisted organic-acid catalysed cellulose were investigated as substrates. Lastly, hydrolysed hemicellulose from fractionated beech wood was applied as substrate. Results U. maydis was characterized on shake flask level regarding its itaconic acid production on glucose. Nitrogen limitation was shown to be a crucial condition for the production of itaconic acid. For itaconic acid concentrations above 25 g/L, a significant product inhibition was observed. Performing experiments that simulated influences of possible pretreatment methods, U. maydis was only slightly affected by high osmolarities up to 3.5 osmol/L as well as of 0.1 M oxalic acid. The production of itaconic acid was achieved on pretreated cellulose in seawater and on the hydrolysed hemicellulosic fraction of pretreated beech wood. Conclusion The fungus U. maydis is a promising producer of itaconic acid, since it grows as single cells (yeast-like in submerged cultivations and it is extremely robust in high osmotic media and real seawater. Moreover, U. maydis can grow on

A two-stage stochastic programming approach for operating multi-energy systems

DEFF Research Database (Denmark)

Zeng, Qing; Fang, Jiakun; Chen, Zhe

2017-01-01

This paper provides a two-stage stochastic programming approach for joint operating multi-energy systems under uncertainty. Simulation is carried out in a test system to demonstrate the feasibility and efficiency of the proposed approach. The test energy system includes a gas subsystem with a gas...

Removal mechanism of tritium by variously pretreated silica gel

International Nuclear Information System (INIS)

Nakashima, M.; Tachikawa, E.; Saeki, M.; Aratono, Y.

1981-01-01

Removal mechanisms of HTO from variously pretreated and non-pretreated silica gel columns were investigated with pulse-loading with tritiated water vapor. With non-pretreated silica gel, the HTO physisorbed on the upper part of the column comes into contact with surface hydroxyl groups while passing downward the column, so that in each equilibration a part of the tritium is incorporated into hydroxyl groups by H/T isotopic exchange reactions. With the silica gel pretreated at a temperature below 400 0 C, most of tritium in the applied HTO is easily incorporated into surface hydroxyl groups in the upper part of the column either by H/T isotopic exchange reactions or by rehydration of the dehydrated surface (siloxyl linkage). In the pretreatment above 400 0 C, essentially all the tritium is trapped by siloxyl groups of various stabilities. The ease of rehydration of siloxyl groups by applied HTO depends on their stabilities, which, in turn, depend on the pretreatment temperature. As a general trend, treatment at higher temperature promotes annealing of the constrained siloxyl groups and thus the rate of rehydration becomes slower. (author)

Dielectric barrier discharge plasma pretreatment on hydrolysis of microcrystalline cellulose

Science.gov (United States)

Huang, Fangmin; Long, Zhouyang; Liu, Sa; Qin, Zhenglong

2017-04-01

Dielectric barrier discharge (DBD) plasma was used as a pretreatment method for downstream hydrolysis of microcrystalline cellulose (MCC). The degree of polymerization (DP) of MCC decreased after it was pretreated by DBD plasma under a carrier gas of air/argon. The effectiveness of depolymerization was found to be influenced by the crystallinity of MCC when under the pretreatment of DBD plasma. With the addition of tert-butyl alcohol in the treated MCC water suspension solution, depolymerization effectiveness of MCC was inhibited. When MCC was pretreated by DBD plasma for 30 min, the total reducing sugar concentration (TRSC) and liquefaction yield (LY) of pretreated-MCC (PMCC) increased by 82.98% and 34.18% respectively compared with those for raw MCC.

The experimental study of a two-stage photovoltaic thermal system based on solar trough concentration

International Nuclear Information System (INIS)

Tan, Lijun; Ji, Xu; Li, Ming; Leng, Congbin; Luo, Xi; Li, Haili

2014-01-01

Highlights: • A two-stage photovoltaic thermal system based on solar trough concentration. • Maximum cell efficiency of 5.21% with the mirror opening width of 57 cm. • With single cycle, maximum temperatures rise in the heating stage is 12.06 °C. • With 30 min multiple cycles, working medium temperature 62.8 °C, increased 28.7 °C. - Abstract: A two-stage photovoltaic thermal system based on solar trough concentration is proposed, in which the metal cavity heating stage is added on the basis of the PV/T stage, and thermal energy with higher temperature is output while electric energy is output. With the 1.8 m 2 mirror PV/T system, the characteristic parameters of the space solar cell under non-concentrating solar radiation and concentrating solar radiation are respectively tested experimentally, and the solar cell output characteristics at different opening widths of concentrating mirror of the PV/T stage under condensation are also tested experimentally. When the mirror opening width was 57 cm, the solar cell efficiency reached maximum value of 5.21%. The experimental platform of the two-stage photovoltaic thermal system was established, with a 1.8 m 2 mirror PV/T stage and a 15 m 2 mirror heating stage, or a 1.8 m 2 mirror PV/T stage and a 30 m 2 mirror heating stage. The results showed that with single cycle, the long metal cavity heating stage would bring lower thermal efficiency, but temperature rise of the working medium is higher, up to 12.06 °C with only single cycle. With 30 min closed multiple cycles, the temperature of the working medium in the water tank was 62.8 °C, with an increase of 28.7 °C, and thermal energy with higher temperature could be output

Potential of potassium hydroxide pretreatment of switchgrass for fermentable sugar production.

Science.gov (United States)

Sharma, Rajat; Palled, Vijaykumar; Sharma-Shivappa, Ratna R; Osborne, Jason

2013-02-01

Chemical pretreatment of lignocellulosic biomass has been extensively investigated for sugar generation and subsequent fuel production. Alkaline pretreatment has emerged as one of the popular chemical pretreatment methods, but most attempts thus far have utilized NaOH for the pretreatment process. This study aimed at investigating the potential of potassium hydroxide (KOH) as a viable alternative alkaline reagent for lignocellulosic pretreatment based on its different reactivity patterns compared to NaOH. Performer switchgrass was pretreated at KOH concentrations of 0.5-2% for varying treatment times of 6-48 h, 6-24 h, and 0.25-1 h at 21, 50, and 121 °C, respectively. The pretreatments resulted in the highest percent sugar retention of 99.26% at 0.5%, 21 °C, 12 h while delignification up to 55.4% was observed with 2% KOH, 121 °C, 1 h. Six pretreatment conditions were selected for subsequent enzymatic hydrolysis with Cellic CTec2® for sugar generation. The pretreatment condition of 0.5% KOH, 24 h, 21 °C was determined to be the most effective as it utilized the least amount of KOH while generating 582.4 mg sugar/g raw biomass for a corresponding percent carbohydrate conversion of 91.8%.

In vacuo substrate pretreatments for enhancing nanodiamond formation in electron cyclotron resonance plasma

International Nuclear Information System (INIS)

Teii, Kungen; Kouzuma, Yutaka; Uchino, Kiichiro

2006-01-01

Substrate pretreatment conditions at low pressures have been examined for enhancing nanocrystalline diamond formation on silicon in electron cyclotron resonance (ECR) plasma. Three kinds of pretreatments (I) exposure to an ECR H 2 plasma with application of a substrate bias from -100 to +30 V (II) hot-filament heating in H 2 gas, and (III) hot-filament heating in vacuum, were used alone or followed by carburization prior to a two-step process of ion-enhanced nucleation in an ECR plasma and subsequent growth in a hot-filament system. The number density of diamond particles after the final growth step was greatly increased up to the order of 10 7 -10 8 cm -2 when applying pretreatment (I) at the bias of 0 V corresponding to the ion-bombardment energy of around 10 eV. In this treatment, a clean and smooth surface with minimal damage was made by the dominance of anisotropic etching by hydrogen ions over isotropic etching by hydrogen atoms. The number density of diamond particles was still more increased when applying pretreatment (II), but the treated surface was unfavorably contaminated and roughened

Effects of different pretreatment methods on fermentation types and dominant bacteria for hydrogen production

Energy Technology Data Exchange (ETDEWEB)

Ren, Nan-Qi; Guo, Wan-Qian; Liu, Bing-Feng; Wang, Xing-Zu; Ding, Jie; Chen, Zhao-Bo [State Key Laboratory of Urban Water Resource and Environment, Harbin Institute of Technology, Harbin 150090, Heilongjiang (China); Wang, Xiang-Jing; Xiang, Wen-Sheng [Research Center of Life Science and Biotechnology, Northeast Agricultural University, Harbin 150030 (China)

2008-08-15

In order to enrich hydrogen producing bacteria and to establish high-efficient communities of the mixed microbial cultures, inoculum needs to be pretreated before the cultivation. Four pretreatment methods including heat-shock pretreatment, acid pretreatment, alkaline pretreatment and repeated-aeration pretreatment were performed on the seed sludge which was collected from a secondary settling tank of a municipal wastewater treatment plant. In contrast to the control test without any pretreatment, the heat-shock pretreatment, acid pretreatment and repeated-aeration pretreatment completely suppressed the methanogenic activity of the seed sludge, but the alkaline pretreatment did not. Employing different pretreatment methods resulted in the change in fermentation types as butyric-acid type fermentation was achieved by the heat-shock and alkaline pretreatments, mixed-acid type fermentation was achieved by acid pretreatment and the control, and ethanol-type fermentation was observed by repeated-aeration pretreatment. Denaturing gradient gel electrophoresis (DGGE) profiles revealed that pretreatment method substantially affected the species composition of microbial communities. The highest hydrogen yield of 1.96 mol/mol-glucose was observed with the repeated-aeration pretreatment method, while the lowest was obtained as the seed sludge was acidified. It is concluded that the pretreatment methods led to the difference in the initial microbial communities which might be directly responsible for different fermentation types and hydrogen yields. (author)

Performance assessment and transient optimization of air precooling in multi-stage solid desiccant air conditioning systems

International Nuclear Information System (INIS)

Gadalla, Mohamed; Saghafifar, Mohammad

2016-01-01

Highlights: • Studying three two-stage solid desiccant cooling systems using Maisotsenko cooler. • Proposing precooling to improve two-stage desiccant systems’ COP for humid climates. • Performing transient analysis for a two-stage solid desiccant cooler in UAE. • Optimizing daily performance of a two-stage solid desiccant cooler for UAE. - Abstract: Renewable energy is one of the most promising solutions to both energy and global warming crisis. Energy consumption can be minimized considerably by utilizing solar energy in air conditioning systems operation. One of the popular solar air conditioning technologies is desiccant air conditioning. Nonetheless, conventional desiccant air conditioning systems have a relatively low coefficient of performance (COP). In consequence, two-stage desiccant air-conditioning systems are proposed to improve desiccant air conditioning systems’ COP. Moreover, a recently commercialized cooling method named Maisotsenko cooling cycle which is capable of cooling air near to its dew point temperature is considered to be integrated within the proposed multi-stage desiccant cooling systems. In this paper, three new two-stage desiccant air conditioning systems incorporating Maisotsenko cooling cycle are proposed and investigated in details for hot and humid climates such as UAE. Furthermore, air precooling is considered to improve two stage desiccant air conditioning systems’ COP. Moreover, full transient analysis and optimization are carried out in UAE within June–October. The proposed system can minimize the required solar heating during noon time as the ambient air dry bulb temperature rises. Average COP of the system during electricity load peak hours (10:00–14:00) for all five considered and combined months is 1.77. Average rate of heat input required to operate the system and average building cooling load are determined to be 100.3 kW and 46.2 kW, respectively. Therefore, system average COP is computed to be 0.46.

Optimization and evaluation of alkaline potassium permanganate pretreatment of corncob.

Science.gov (United States)

Ma, Lijuan; Cui, Youzhi; Cai, Rui; Liu, Xueqiang; Zhang, Cuiying; Xiao, Dongguang

2015-03-01

Alkaline potassium permanganate solution (APP) was applied to the pretreatment of corncob with a simple and effective optimization of APP concentration, reaction time, temperature and solid to liquid ratio (SLR). The optimized pretreatment conditions were at 2% (w/v) potassium permanganate with SLR of 1:10 treating for 6h at 50°C. This simple one-step treatment resulted in significant 94.56% of the cellulose and 81.47% of the hemicellulose recoveries and 46.79% of the lignin removal of corncob. The reducing sugar in the hydrolysate from APP-pretreated corncob was 8.39g/L after 12h enzymatic hydrolysis, which was 1.44 and 1.29 folds higher than those from raw and acid pretreated corncobs. Physical characteristics, crystallinity and structure of the pretreated corncob were analyzed and assessed by SEM, XRD and FTIR. The APP pretreatment process was novel and enhanced enzymatic hydrolysis of lignocellulose by affecting composition and structural features. Copyright © 2014 Elsevier Ltd. All rights reserved.

Improved pretreatment of lignocellulosic biomass using enzymatically-generated peracetic acid.

Science.gov (United States)

Yin, DeLu Tyler; Jing, Qing; AlDajani, Waleed Wafa; Duncan, Shona; Tschirner, Ulrike; Schilling, Jonathan; Kazlauskas, Romas J

2011-04-01

Release of sugars from lignocellulosic biomass is inefficient because lignin, an aromatic polymer, blocks access of enzymes to the sugar polymers. Pretreatments remove lignin and disrupt its structure, thereby enhancing sugar release. In previous work, enzymatically generated peracetic acid was used to pretreat aspen wood. This pretreatment removed 45% of the lignin and the subsequent saccharification released 97% of the sugars remaining after pretreatment. In this paper, the amount of enzyme needed is reduced tenfold using first, an improved enzyme variant that makes twice as much peracetic acid and second, a two-phase reaction to generate the peracetic acid, which allows enzyme reuse. In addition, the eight pretreatment cycles are reduced to only one by increasing the volume of peracetic acid solution and increasing the temperature to 60 °C and the reaction time to 6h. For the pretreatment step, the weight ratio of peracetic acid to wood determines the amount of lignin removed. Copyright © 2011 Elsevier Ltd. All rights reserved.

Case Study of a Small Scale Reverse Osmosis System for Treatment of Mixed Brackish Water and STP Effluent

Directory of Open Access Journals (Sweden)

I Nyoman Widiasa

2017-04-01

Full Text Available A case study on utilizing reverse osmosis (RO technology to fulfill fresh water needs at a mall and a hotel has been done on Bali Island, Indonesia. A mix of brackish water and sewage treatment plant (STP effluent was used as feed water in the RO system. The system used 36 membrane elements (CSM RE 8040 BLN arranged into two stages: 8 pressure vessels (PVs in the first stage and 4 PVs in the second stage, each loaded with 3 membranes. The objectives of this research were to assess the cleaning effectivity in the plant, to evaluate the cleaning of 1 membrane element using a CIP system, and to assess the use of the membrane for filtration in the pre-treatment system. SEM and FTIR analysis indicated that the foulants on the membrane surface were dominated by organic foulants and inorganic deposits. To clean the discarded membrane the proposed method used NaOH solution (pH 12 and pH 13 and citric acid (pH 2 and pH 3. All membranes displayed a dramatic decline in rejection of about 80%. Based on the rejection tests of SO42-, Cl-, turbidity reduction approached 100%. It can be concluded that an RO membrane that has undergone selectivity decline can be re-used as a filtration membrane in the pre-treatment system.

Size effects on acid bisulfite pretreatment efficiency: multiple product yields in spent liquor and enzymatic digestibility of pretreated solids

Science.gov (United States)

Yalan Liu; Jinwu Wang; Michael P. Wolcott

2017-01-01

Currently, feedstock size effects on chemical pretreatment performance were not clear due to the complexity of the pretreatment process and multiple evaluation standards such as the sugar recovery in spent liquor or enzymatic digestibility. In this study, we evaluated the size effects by various ways: the sugar recovery and coproduct yields in spent liquor, the...

A two-stage stochastic programming model for the optimal design of distributed energy systems

International Nuclear Information System (INIS)

Zhou, Zhe; Zhang, Jianyun; Liu, Pei; Li, Zheng; Georgiadis, Michael C.; Pistikopoulos, Efstratios N.

2013-01-01

Highlights: ► The optimal design of distributed energy systems under uncertainty is studied. ► A stochastic model is developed using genetic algorithm and Monte Carlo method. ► The proposed system possesses inherent robustness under uncertainty. ► The inherent robustness is due to energy storage facilities and grid connection. -- Abstract: A distributed energy system is a multi-input and multi-output energy system with substantial energy, economic and environmental benefits. The optimal design of such a complex system under energy demand and supply uncertainty poses significant challenges in terms of both modelling and corresponding solution strategies. This paper proposes a two-stage stochastic programming model for the optimal design of distributed energy systems. A two-stage decomposition based solution strategy is used to solve the optimization problem with genetic algorithm performing the search on the first stage variables and a Monte Carlo method dealing with uncertainty in the second stage. The model is applied to the planning of a distributed energy system in a hotel. Detailed computational results are presented and compared with those generated by a deterministic model. The impacts of demand and supply uncertainty on the optimal design of distributed energy systems are systematically investigated using proposed modelling framework and solution approach.

Comparison of single-stage and temperature-phased two-stage anaerobic digestion of oily food waste

International Nuclear Information System (INIS)

Wu, Li-Jie; Kobayashi, Takuro; Li, Yu-You; Xu, Kai-Qin

2015-01-01

Highlights: • A single-stage and two two-stage anaerobic systems were synchronously operated. • Similar methane production 0.44 L/g VS_a_d_d_e_d from oily food waste was achieved. • The first stage of the two-stage process became inefficient due to serious pH drop. • Recycle favored the hythan production in the two-stage digestion. • The conversion of unsaturated fatty acids was enhanced by recycle introduction. - Abstract: Anaerobic digestion is an effective technology to recover energy from oily food waste. A single-stage system and temperature-phased two-stage systems with and without recycle for anaerobic digestion of oily food waste were constructed to compare the operation performances. The synchronous operation indicated the similar ability to produce methane in the three systems, with a methane yield of 0.44 L/g VS_a_d_d_e_d. The pH drop to less than 4.0 in the first stage of two-stage system without recycle resulted in poor hydrolysis, and methane or hydrogen was not produced in this stage. Alkalinity supplement from the second stage of two-stage system with recycle improved pH in the first stage to 5.4. Consequently, 35.3% of the particulate COD in the influent was reduced in the first stage of two-stage system with recycle according to a COD mass balance, and hydrogen was produced with a percentage of 31.7%, accordingly. Similar solids and organic matter were removed in the single-stage system and two-stage system without recycle. More lipid degradation and the conversion of long-chain fatty acids were achieved in the single-stage system. Recycling was proved to be effective in promoting the conversion of unsaturated long-chain fatty acids into saturated fatty acids in the two-stage system.

Pretreatment of Biomass by Aqueous Ammonia for Bioethanol Production

Science.gov (United States)

Kim, Tae Hyun; Gupta, Rajesh; Lee, Y. Y.

The methods of pretreatment of lignocellulosic biomass using aqueous ammonia are described. The main effect of ammonia treatment of biomass is delignification without significantly affecting the carbohydrate contents. It is a very effective pretreatment method especially for substrates that have low lignin contents such as agricultural residues and herbaceous feedstock. The ammonia-based pretreatment is well suited for simultaneous saccharification and co-fermentation (SSCF) because the treated biomass retains cellulose as well as hemicellulose. It has been demonstrated that overall ethanol yield above 75% of the theoretical maximum on the basis of total carbohydrate is achievable from corn stover pretreated with aqueous ammonia by way of SSCF. There are two different types of pretreatment methods based on aqueous ammonia: (1) high severity, low contact time process (ammonia recycle percolation; ARP), (2) low severity, high treatment time process (soaking in aqueous ammonia; SAA). Both of these methods are described and discussed for their features and effectiveness.

Flow-through pretreatment of lignocellulosic biomass with inorganic nanoporous membranes

Energy Technology Data Exchange (ETDEWEB)

Bhave, Ramesh R.; Lynd, Lee; Shao, Xiongjun

2018-04-03

A process for the pretreatment of lignocellulosic biomass is provided. The process generally includes flowing water through a pretreatment reactor containing a bed of particulate ligno-cellulosic biomass to produce a pressurized, high-temperature hydrolyzate exit stream, separating solubilized compounds from the hydrolyzate exit stream using an inorganic nanoporous membrane element, fractionating the retentate enriched in solubilized organic components and recycling the permeate to the pretreatment reactor. The pretreatment process provides solubilized organics in concentrated form for the subsequent conversion into biofuels and other chemicals.

Enzymatic protein hydrolysates from high pressure-pretreated isolated pea proteins have better antioxidant properties than similar hydrolysates produced from heat pretreatment.

Science.gov (United States)

Girgih, Abraham T; Chao, Dongfang; Lin, Lin; He, Rong; Jung, Stephanie; Aluko, Rotimi E

2015-12-01

Isolated pea protein (IPP) dispersions (1%, w/v) were pretreated with high pressure (HP) of 200, 400, or 600 MPa for 5 min at 24 °C or high temperature (HT) for 30 min at 100 °C prior to hydrolysis with 1% (w/w) Alcalase. HP pretreatment of IPP at 400 and 600 MPa levels led to significantly (P40%) oxygen radical absorption capacity (ORAC) of hydrolysates. 2,2-Diphenyl-1-picrylhydrazyl, superoxide radical and hydroxyl radical scavenging activities of pea protein hydrolysates were also significantly (PProtein hydrolysates from HT IPP showed no ORAC, superoxide or hydroxyl scavenging activity but had significantly (Pprotein hydrolysates had weaker antioxidant properties than glutathione but overall, the HP pretreatment was superior to HT pretreatment in facilitating enzymatic release of antioxidant peptides from IPP. Copyright © 2015 Elsevier Ltd. All rights reserved.

Wet oxidation pretreatment of rape straw for ethanol production

International Nuclear Information System (INIS)

Arvaniti, Efthalia; Bjerre, Anne Belinda; Schmidt, Jens Ejbye

2012-01-01

Rape straw can be used for production of second generation bioethanol. In this paper we optimized the pretreatment of rape straw for this purpose using Wet oxidation (WO). The effect of reaction temperature, reaction time, and oxygen gas pressure was investigated for maximum ethanol yield via Simultaneous Saccharification and Fermentation (SSF). To reduce the water use and increase the energy efficiency in WO pretreatment features like recycling liquid (filtrate), presoaking of rape straw in water or recycled filtrate before WO, skip washing pretreated solids (filter cake) after WO, or use of whole slurry (Filter cake + filtrate) in SSF were also tested. Except ethanol yields, pretreatment methods were evaluated based on achieved glucose yields, amount of water used, recovery of cellulose, hemicellulose, and lignin. The highest ethanol yield obtained was 67% after fermenting the whole slurry produced by WO at 205 °C for 3 min with 12 bar of oxygen gas pressure and featured with presoaking in water. At these conditions after pre-treatment, cellulose and hemicellulose was recovered quantitatively (100%) together with 86% of the lignin. WO treatments of 2–3 min at 205–210 °C with 12 bar of oxygen gas produced higher ethanol yields and cellulose, hemicelluloses, and lignin recoveries, than 15 min WO treatment at 195 °C. Also, recycling filtrate and use of higher oxygen gas pressure reduced recovery of materials. The use of filtrate could be inhibitory for the yeast, but also reduced lactic acid formation in SSF. -- Highlights: ► Wet Oxidation pretreatment on rape straw for sugar and ethanol production. ► Variables were reaction time, temperature, and oxygen gas pressure. ► Also, other configurations for increase of water and energy efficiency. ► Short Wet oxidation pretreatment (2–3 min) produced highest ethanol yield. ► After these pretreatment conditions recovery of lignin in solids was 86%.

Investigation of Pleurotus ostreatus pretreatment on switchgrass for ethanol production

Science.gov (United States)

Slavens, Shelyn Gehle

Fungal pretreatment using the white-rot fungus Pleurotus ostreatus on switchgrass for ethanol production was studied. In a small-scale storage study, small switchgrass bales were inoculated with fungal spawn and automatically watered to maintain moisture. Sampled at 25, 53, and 81 d, the switchgrass composition was determined and liquid hot water (LHW) pretreatment was conducted. Fungal pretreatment significantly decreased the xylan and lignin content; glucan was not significantly affected by fungal loading. The glucan, xylan, and lignin contents significantly decreased with increased fungal pretreatment time. The effects of the fungal pretreatment were not highly evident after the LHW pretreatment, showing only changes based on sampling time. Although other biological activity within the bales increased cellulose degradation, the fungal pretreatment successfully reduced the switchgrass lignin and hemicellulose contents. In a laboratory-scale nutrient supplementation study, copper, manganese, glucose, or water was added to switchgrass to induce production of ligninolytic enzymes by P. ostreatus. After 40 d, ligninolytic enzyme activities and biomass composition were determined and simultaneous saccharification and fermentation (SSF) was conducted to determine ethanol yield. Laccase activity was similar for all supplements and manganese peroxidase (MnP) activity was significantly less in copper-treated samples than in the other fungal-inoculated samples. The fungal pretreatment reduced glucan, xylan, and lignin content, while increasing extractable sugars content. The lowest lignin contents occurred in the water-fungal treated samples and produced the greatest ethanol yields. The greatest lignin contents occurred in the copper-fungal treated samples and produced the lowest ethanol yields. Manganese-fungal and glucose-fungal treated samples had similar, intermediate lignin contents and produced similar, intermediate ethanol yields. Ethanol yields from switchgrass

Rheological evaluation of pretreated cladding removal waste

International Nuclear Information System (INIS)

McCarthy, D.; Chan, M.K.C.; Lokken, R.O.

1986-01-01

Cladding removal waste (CRW) contains concentrations of transuranic (TRU) elements in the 80 to 350 nCi/g range. This waste will require pretreatment before it can be disposed of as glass or grout at Hanford. The CRW will be pretreated with a rare earth strike and solids removal by centrifugation to segregate the TRU fraction from the non-TRU fraction of the waste. The centrifuge centrate will be neutralized with sodium hydroxide. This neutralized cladding removal waste (NCRW) is expected to be suitable for grouting. The TRU solids removed by centrifugation will be vitrified. The goal of the Rheological Evaluation of Pretreated Cladding Removal Waste Program was to evaluate those rheological and transport properties critical to assuring successful handling of the NCRW and TRU solids streams and to demonstrate transfers in a semi-prototypic pumping environment. This goal was achieved by a combination of laboratory and pilot-scale evaluations. The results obtained during these evaluations were correlated with classical rheological models and scaled-up to predict the performance that is likely to occur in the full-scale system. The Program used simulated NCRW and TRU solid slurries. Rockwell Hanford Operations (Rockwell) provided 150 gallons of simulated CRW and 5 gallons of simulated TRU solid slurry. The simulated CRW was neutralized by Pacific Northwest Laboratory (PNL). The physical and rheological properties of the NCRW and TRU solid slurries were evaluated in the laboratory. The properties displayed by NCRW allowed it to be classified as a pseudoplastic or yield-pseudoplastic non-Newtonian fluid. The TRU solids slurry contained very few solids. This slurry exhibited the properties associated with a pseudoplastic non-Newtonian fluid

Literature Review of Physical and Chemical Pretreatment Processes for Lignocellulosic Biomass

Energy Technology Data Exchange (ETDEWEB)

Harmsen, P.; Bakker, R. [Wageningen University and Research centre WUR, Food and Biobased Research WUR-FBR, Wageningen (Netherlands); Huijgen, W.J.J. [ECN Biomass, Coal and Environment, Petten (Netherlands); Bermudez Lopez, L. [Abengoa Bioenergia Nuevas Tecnologias ABNT (Spain)

2010-09-15

This literature review was performed within the BioSynergy project (2007-2010). BioSynergy is a European Integrated Project supported through the Sixth Framework Programme for Research and Technological Development (038994-SES6). BioSynergy stands for 'BIOmass for the market competitive and environmentally friendly SYNthesis of bio-products together with the production of secondary enERGY carriers through the biorefinery approach'. Within the BioSynergy project the overall goal of the pretreatment routes being developed is to convert raw lignocellulosic biomass into its composing sugars and lignin in a market competitive and environmentally sustainable way. This report reviews lignocellulose pretreatment in general as well as specific pretreatment technologies that are developed within the BioSynergy project including steam explosion (ABNT), mechanical/alkaline fractionation (WUR) and organosolv fractionation (ECN). In addition to these pretreatment technologies, other pretreatment technologies are studied within the BioSynergy project such as acetic/formic acid pretreatment and mild- and strong acid pretreatment.

Mechanism of waste biomass pyrolysis: Effect of physical and chemical pre-treatments

International Nuclear Information System (INIS)

Das, Oisik; Sarmah, Ajit K.

2015-01-01

To impart usability in waste based biomass through thermo-chemical reactions, several physical and chemical pre-treatments were conducted to gain an insight on their mode of action, effect on the chemistry and the change in thermal degradation profiles. Two different waste biomasses (Douglas fir, a softwood and hybrid poplar, a hardwood) were subjected to four different pre-treatments, namely, hot water pre-treatment, torrefaction, acid (sulphuric acid) and salt (ammonium phosphate) doping. Post pre-treatments, the changes in the biomass structure, chemistry, and thermal makeup were studied through electron microscopy, atomic absorption/ultra violet spectroscopy, ion exchange chromatography, and thermogravimetry. The pre-treatments significantly reduced the amounts of inorganic ash, extractives, metals, and hemicellulose from both the biomass samples. Furthermore, hot water and torrefaction pre-treatment caused mechanical disruption in biomass fibres leading to smaller particle sizes. Torrefaction of Douglas fir wood yielded more solid product than hybrid poplar. Finally, the salt pre-treatment increased the activation energies of the biomass samples (especially Douglas fir) to a great extent. Thus, salt pre-treatment was found to bestow thermal stability in the biomass. - Highlights: • Pre-treatments reduce ash, extractives, alkalines and hemicellulose from biomass. • Torrefaction of Douglas fir yields more solid product than hybrid poplar. • Salt pretreatment significantly increases the activation energy of biomass. • Acid and salt pretreatment bestows thermal stability in biomass.

Mechanism of waste biomass pyrolysis: Effect of physical and chemical pre-treatments

Energy Technology Data Exchange (ETDEWEB)

Das, Oisik [Department of Biological Systems Engineering, Washington State University, Pullman 99164-6120, WA (United States); Department of Civil and Environmental Engineering, University of Auckland, Auckland 1142 (New Zealand); Sarmah, Ajit K., E-mail: a.sarmah@auckland.ac.nz [Department of Civil and Environmental Engineering, University of Auckland, Auckland 1142 (New Zealand)

2015-12-15

To impart usability in waste based biomass through thermo-chemical reactions, several physical and chemical pre-treatments were conducted to gain an insight on their mode of action, effect on the chemistry and the change in thermal degradation profiles. Two different waste biomasses (Douglas fir, a softwood and hybrid poplar, a hardwood) were subjected to four different pre-treatments, namely, hot water pre-treatment, torrefaction, acid (sulphuric acid) and salt (ammonium phosphate) doping. Post pre-treatments, the changes in the biomass structure, chemistry, and thermal makeup were studied through electron microscopy, atomic absorption/ultra violet spectroscopy, ion exchange chromatography, and thermogravimetry. The pre-treatments significantly reduced the amounts of inorganic ash, extractives, metals, and hemicellulose from both the biomass samples. Furthermore, hot water and torrefaction pre-treatment caused mechanical disruption in biomass fibres leading to smaller particle sizes. Torrefaction of Douglas fir wood yielded more solid product than hybrid poplar. Finally, the salt pre-treatment increased the activation energies of the biomass samples (especially Douglas fir) to a great extent. Thus, salt pre-treatment was found to bestow thermal stability in the biomass. - Highlights: • Pre-treatments reduce ash, extractives, alkalines and hemicellulose from biomass. • Torrefaction of Douglas fir yields more solid product than hybrid poplar. • Salt pretreatment significantly increases the activation energy of biomass. • Acid and salt pretreatment bestows thermal stability in biomass.

Development and application of a labmade apparatus using open-source “arduino” hardware for the electrochemical pretreatment of boron-doped diamond electrodes

International Nuclear Information System (INIS)

Rosa, Thalles Ramon; Betim, Fernando Silva; Ferreira, Rafael de Queiroz

2017-01-01

Highlights: • BDD electrodes use an electrochemical pretreatment (anodic and/or cathodic) to restore their original characteristics and promote the reproduction of previous voltammograms; • Automatic system can carefully reproduce the electrochemical pretreatment of BDD electrode quickly and efficiently; • Open source platform “Arduino” can be used to developed a labmade apparatus to control a BDD electrode pretreatment system for analytical purposes; • The main advantages of this labmade apparatus are: low supporting electrolyte consumption (20 mL), a total time for each pretreatment of 80 seconds and an average cost of production below US$ 200. - Abstract: Every day, new electroanalytical methodologies are developed to supplant the established spectrometric and chromatographic methods due to their versatility, low cost and ability to perform measurements without sample treatment. Electroanalytical techniques have provided an alternative to quantify substances due to the direct relationship between the analyte concentration and some electrical property of the system. However, this ratio between the concentration and peak current is valid only if the electrochemically active area of the working electrode is constant in each electrochemical test. For years, classic polarography ensured the reproducibility of the mercury electrode surface due to its liquid state at room temperature. However, this metal has a high toxicity, driving the search for new inert materials for their replacement, most notably boron-doped diamond (BDD) electrodes. This electrode material has, among other attractive advantages for electroanalysis, a potential range higher than that of the mercury working electrode under the same conditions. Solid electrodes are, in general, polished to promote the reproducibility of their electrochemical performance. For BDD, the use of an electrochemical pretreatment (anodic and/or cathodic) has been sufficient to restore their original

Pretreatment Characteristics of Waste Oak Wood by Ammonia Percolation

Science.gov (United States)

Kim, Jun-Seok; Kim, Hyunjoon; Lee, Jin-Suk; Lee, Joon-Pyo; Park, Soon-Chul

A log of waste oak wood collected from a Korean mushroom farm has been tested for ammonia percolation pretreatment. The waste log has different physical characteristics from that of virgin oak wood. The density of the waste wood was 30% lower than that of virgin oak wood. However, there is little difference in the chemical compositions between the woods. Due to the difference in physical characteristics, the optimal pretreatment conditions were also quite different. While for waste oak the optimum temperature was determined to be 130°C, for virgin oak wood the optimum pretreatment was only achieved at 170°C. Presoaking for 12 h with ammonia solution before pretreatment was helpful to increase the delignification efficiency.

40 CFR 455.46 - Pretreatment standards for existing sources (PSES).

Science.gov (United States)

2010-07-01

... pretreated at the facility. The Control Authority may waive pretreatment for these two wastewaters only if... Authority at the time of renewing or modifying its individual control mechanism or pretreatment agreement of... Authority an initial certification statement as described in § 455.41(a); (3) The discharger will submit to...

Low-dose radiation pretreatment improves survival of human ceiling culture-derived proliferative adipocytes (ccdPAs) under hypoxia via HIF-1 alpha and MMP-2 induction

International Nuclear Information System (INIS)

Adachi, Naoki; Kubota, Yoshitaka; Kosaka, Kentarou; Akita, Shinsuke; Sasahara, Yoshitarou; Kira, Tomoe; Kuroda, Masayuki; Mitsukawa, Nobuyuki; Bujo, Hideaki; Satoh, Kaneshige

2015-01-01

Poor survival is a major problem of adipocyte transplantation. We previously reported that VEGF and MMPs secreted from transplanted adipocytes are essential for angiogenesis and adipogenesis. Pretreatment with low-dose (5 Gy) radiation (LDR) increased VEGF, MMP-2, and HIF-1 alpha mRNA expression in human ceiling culture-derived proliferative adipocytes (hccdPAs). Gene expression after LDR differed between adipose-derived stem cells (hASCs) and hccdPAs. Pretreatment with LDR improved the survival of hccdPAs under hypoxia, which is inevitable in the early stages after transplantation. Upregulation of VEGF and MMP-2 after LDR in hccdPAs is mediated by HIF-1 alpha expression. Our results suggest that pretreatment with LDR may improve adipocyte graft survival in a clinical setting through upregulation of VEGF and MMP-2 via HIF-1 alpha. - Highlights: • Ceiling culture-derived proliferative adipocytes (ccdPAs) react to radiation. • Low-dose radiation (LDR) pretreatment improves survival of ccdPAs under hypoxia. • Gene expression after LDR differs between ccdPAs and adipose-derived stem cells. • LDR-induced increase in MMP-2 and VEGF is dependent on HIF-1 alpha induction. • LDR pretreatment may improve the adipocyte graft survival rate in clinical settings

Low-dose radiation pretreatment improves survival of human ceiling culture-derived proliferative adipocytes (ccdPAs) under hypoxia via HIF-1 alpha and MMP-2 induction

Energy Technology Data Exchange (ETDEWEB)

Adachi, Naoki [Department of Plastic Surgery, Chiba University, 1-8-1, Inohana, Chuo-ku, Chiba-city, Chiba, #260-8677 (Japan); Kubota, Yoshitaka, E-mail: kubota-cbu@umin.ac.jp [Department of Plastic Surgery, Chiba University, 1-8-1, Inohana, Chuo-ku, Chiba-city, Chiba, #260-8677 (Japan); Kosaka, Kentarou; Akita, Shinsuke; Sasahara, Yoshitarou; Kira, Tomoe [Department of Plastic Surgery, Chiba University, 1-8-1, Inohana, Chuo-ku, Chiba-city, Chiba, #260-8677 (Japan); Kuroda, Masayuki [Center for Advanced Medicine, Chiba University, 1-8-1, Inohana, Chuo-ku, Chiba-city, Chiba, #260-8677 (Japan); Mitsukawa, Nobuyuki [Department of Plastic Surgery, Chiba University, 1-8-1, Inohana, Chuo-ku, Chiba-city, Chiba, #260-8677 (Japan); Bujo, Hideaki [Department of Clinical-Laboratory and Experimental-Research Medicine, Toho University, Sakura Medical Center, 564-1 Shimoshizu, Sakura-shi, Chiba, #285-8741 (Japan); Satoh, Kaneshige [Department of Plastic Surgery, Chiba University, 1-8-1, Inohana, Chuo-ku, Chiba-city, Chiba, #260-8677 (Japan)

2015-08-07

Poor survival is a major problem of adipocyte transplantation. We previously reported that VEGF and MMPs secreted from transplanted adipocytes are essential for angiogenesis and adipogenesis. Pretreatment with low-dose (5 Gy) radiation (LDR) increased VEGF, MMP-2, and HIF-1 alpha mRNA expression in human ceiling culture-derived proliferative adipocytes (hccdPAs). Gene expression after LDR differed between adipose-derived stem cells (hASCs) and hccdPAs. Pretreatment with LDR improved the survival of hccdPAs under hypoxia, which is inevitable in the early stages after transplantation. Upregulation of VEGF and MMP-2 after LDR in hccdPAs is mediated by HIF-1 alpha expression. Our results suggest that pretreatment with LDR may improve adipocyte graft survival in a clinical setting through upregulation of VEGF and MMP-2 via HIF-1 alpha. - Highlights: • Ceiling culture-derived proliferative adipocytes (ccdPAs) react to radiation. • Low-dose radiation (LDR) pretreatment improves survival of ccdPAs under hypoxia. • Gene expression after LDR differs between ccdPAs and adipose-derived stem cells. • LDR-induced increase in MMP-2 and VEGF is dependent on HIF-1 alpha induction. • LDR pretreatment may improve the adipocyte graft survival rate in clinical settings.

Comparison of microwave and conduction-convection heating autohydrolysis pretreatment for bioethanol production.

Science.gov (United States)

Aguilar-Reynosa, Alejandra; Romaní, Aloia; Rodríguez-Jasso, Rosa M; Aguilar, Cristóbal N; Garrote, Gil; Ruiz, Héctor A

2017-11-01

This work describes the application of two forms of heating for autohydrolysis pretreatment on isothermal regimen: conduction-convection heating and microwave heating processing using corn stover as raw material for bioethanol production. Pretreatments were performed using different operational conditions: residence time (10-50 min) and temperature (160-200°C) for both pretreatments. Subsequently, the susceptibility of pretreated solids was studied using low enzyme loads, and high substrate loads. The highest conversion was 95.1% for microwave pretreated solids. Also solids pretreated by microwave heating processing showed better ethanol conversion in simultaneous saccharification and fermentation process (92% corresponding to 33.8g/L). Therefore, microwave heating processing is a promising technology in the pretreatment of lignocellulosic materials. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Enhancement of anaerobic digestion of excess sludge by acid-alkali pretreatment].

Science.gov (United States)

Yuan, Guang-Huan; Zhou, Xing-Qiu; Wu, Jian-Dong

2012-06-01

In order to enhance the efficiency of anaerobic digestion of excess sludge, acid-alkali pretreatment method was studied. Three different pretreatment methods (alkali alone,acid-alkali, alkali-acid) were compared to investigate their impacts on hydrolysis and acidification of activated sludge. In addition, their influences on methane-producing in subsequent anaerobic digestion process were also studied. The results showed that the soluble chemical oxygen demand (SCOD) of alkaline treatment alone was about 16% higher than the combining of acid and alkali treatment, SCOD concentration increased to 5406.1 mg x L(-1) after 8 d pretreatment. After treated by acid (pH 4.0, 4 d) and alkali (pH 10.0, 4 d), the acetic acid production and its content in short-chain fatty acids (SCFAs) were higher than other pretreatment methods. And the acetic acid production (as COD/VSS) could reach 74.4 mg x g(-1), accounting for 60.5% of SCFAs. After acid-alkali pretreatment, the C: N ratio of the sludge mixed liquor was about 25, and the C: P ratio was between 35-40, which was more favorable than C: N and C: P ratio of alkali alone and alkali-acid to subsequent anaerobic digestion. The control experiments showed that, after acid-alkali pretreatment, anaerobic digestion cumulative methane yield (CH4/VSS(in)) reached to 136.1 mL x g(-1) at 15 d, which was about 2.5-, 1.6-, and 1.7-fold of the blank (unpretreated), alkali alone pretreatment and alkali-acid pretreatment, respectively. After acid-alkali pretreatment for 8 d and anaerobic digestion for 15 d, the removal efficiency of VSS was about 60.9%, and the sludge reduction effect was better than other pretreatments. It is obvious that the acid-alkali pretreatment method was more favorable to anaerobic digestion and sludge reduction.

A Two-stage DC-DC Converter for the Fuel Cell-Supercapacitor Hybrid System

DEFF Research Database (Denmark)

Zhang, Zhe; Thomsen, Ole Cornelius; Andersen, Michael A. E.

2009-01-01

A wide input range multi-stage converter is proposed with the fuel cells and supercapacitors as a hybrid system. The front-end two-phase boost converter is used to optimize the output power and to reduce the current ripple of fuel cells. The supercapacitor power module is connected by push...... and designed. A 1kW prototype controlled by TMS320F2808 DSP is built in the lab. Simulation and experimental results confirm the feasibility of the proposed two stage dc-dc converter system.......-pull-forward half bridge (PPFHB) converter with coupled inductors in the second stage to handle the slow transient response of the fuel cells and realize the bidirectional power flow control. Moreover, this cascaded structure simplifies the power management. The control strategy for the whole system is analyzed...

Two-stage energy storage equalization system for lithium-ion battery pack

Science.gov (United States)

Chen, W.; Yang, Z. X.; Dong, G. Q.; Li, Y. B.; He, Q. Y.

2017-11-01

How to raise the efficiency of energy storage and maximize storage capacity is a core problem in current energy storage management. For that, two-stage energy storage equalization system which contains two-stage equalization topology and control strategy based on a symmetric multi-winding transformer and DC-DC (direct current-direct current) converter is proposed with bidirectional active equalization theory, in order to realize the objectives of consistent lithium-ion battery packs voltages and cells voltages inside packs by using a method of the Range. Modeling analysis demonstrates that the voltage dispersion of lithium-ion battery packs and cells inside packs can be kept within 2 percent during charging and discharging. Equalization time was 0.5 ms, which shortened equalization time of 33.3 percent compared with DC-DC converter. Therefore, the proposed two-stage lithium-ion battery equalization system can achieve maximum storage capacity between lithium-ion battery packs and cells inside packs, meanwhile efficiency of energy storage is significantly improved.

Enzymatic conversion of pretreated biomass into fermentable sugars for biorefinery operation

Science.gov (United States)

Gao, Dahai

2011-12-01

formed during pretreatment impede accurate quantification of individual glycosyl hydrolases (GH) binding to pretreated cell walls. A high-throughput Fast Protein Liquid Chromatography (HT-FPLC) based method has been developed to quantify CBH I, CBH II and EG I present in hydrolyzates of untreated, AFEX, and dilute-acid pretreated corn stover. This method can accurately quantify individual enzymes present in complex binary and ternary protein mixtures without interference from plant cell wall derived components. The binding characteristics of CBH I, CBH II and EG I during 48 hours hydrolysis were studied on different cellulose allomorphs: microcrystalline cellulose Avicel (cellulose Ibeta), liquid ammonia treated cellulose (cellulose III), sodium hydroxide treated cellulose (cellulose II) and phosphoric acid swollen amorphous cellulose (AC). The digestibility ranking is AC>cellulose III>cellulose II>cellulose I. However, AC has the highest initial enzyme binding capacity while cellulose III had the lowest. CBH II is less stable during hydrolysis. Time course binding studies were also performed for pretreated biomass. Ammonia Fiber Expansion (AFEX) treated corn stover (CS), dilute acid (ACID) treated CS and ionic liquid (IL) pretreated CS were compared. The results indicate that presence of lignin is responsible for significant unproductive cellulase binding. These results are critical for improving our understanding of enzyme synergism, productive/unproductive enzyme binding and the role of pretreatment on enzyme accessibility to lignocellulosic plant cell walls. The results also assist in engineering novel low unproductive binding enzyme systems and developing economic enzyme recycle options.

Target tracking system based on preliminary and precise two-stage compound cameras

Science.gov (United States)

Shen, Yiyan; Hu, Ruolan; She, Jun; Luo, Yiming; Zhou, Jie

2018-02-01

Early detection of goals and high-precision of target tracking is two important performance indicators which need to be balanced in actual target search tracking system. This paper proposed a target tracking system with preliminary and precise two - stage compound. This system using a large field of view to achieve the target search. After the target was searched and confirmed, switch into a small field of view for two field of view target tracking. In this system, an appropriate filed switching strategy is the key to achieve tracking. At the same time, two groups PID parameters are add into the system to reduce tracking error. This combination way with preliminary and precise two-stage compound can extend the scope of the target and improve the target tracking accuracy and this method has practical value.

Ultrastructural characterization of rice husk submitted to different pretreatments to optimize its fermentation

Energy Technology Data Exchange (ETDEWEB)

Lhoneux, B de; Gerlache, L; Clemente, A; Roda-Santos, M L; Menaia, J A.G.; Fernandes, T H

1988-01-01

Silica distribution in rice husk was examined by scanning electron microscopy. Silica appeared as a solid structure in the outer epidermis and as a dispersed system inside the husk. Pretreatments (steam autoclaving, water autoclaving, alkaline leaching, gamma irradiation, and ultra sound) were applied in order to achieve an improvement in rice husk digestibility. Alkaline leaching removed a significant part of the silica structure, therefore allowing a larger area of exposure of the cell wall polymers to the degrading enzymes. Among the pretreatments, alkaline leaching appeared to be the most useful, while others seemed not to be very successful in attaining the desired effect.

ALA Pretreatment Improves Waterlogging Tolerance of Fig Plants.

Directory of Open Access Journals (Sweden)

Yuyan An

Full Text Available 5-aminolevulinic acid (ALA, a natural and environmentally friendly plant growth regulator, can improve plant tolerance to various environmental stresses. However, whether ALA can improve plant waterlogging tolerance is unknown. Here, we investigated the effects of ALA pretreatment on the waterlogging-induced damage of fig (Ficus carica Linn. plants, which often suffer from waterlogging stress. ALA pretreatment significantly alleviated stress-induced morphological damage, increased leaf relative water content (RWC, and reduced leaf superoxide anion ([Formula: see text] production rate and malonaldehyde (MDA content in fig leaves, indicating ALA mitigates waterlogging stress of fig plants. We further demonstrated that ALA pretreatment largely promoted leaf chlorophyll content, photosynthetic electron transfer ability, and photosynthetic performance index, indicating ALA significantly improves plant photosynthetic efficiency under waterlogging stress. Moreover, ALA pretreatment significantly increased activities of leaf superoxide dismutase (SOD and peroxidase (POD, root vigor, and activities of root alcohol dehydrogenase (ADH, and lactate dehydrogenase (LDH, indicating ALA also significantly improves antioxidant ability and root function of fig plants under waterlogging stress. Taken together, ALA pretreatment improves waterlogging tolerance of fig plants significantly, and the promoted root respiration, leaf photosynthesis, and antioxidant ability may contribute greatly to this improvement. Our data firstly shows that ALA can improve plant waterlogging tolerance.

Coupling effect and control strategies of the maglev dual-stage inertially stabilization system based on frequency-domain analysis.

Science.gov (United States)

Lin, Zhuchong; Liu, Kun; Zhang, Li; Zeng, Delin

2016-09-01

Maglev dual-stage inertially stabilization (MDIS) system is a newly proposed system which combines a conventional two-axis gimbal assembly and a 5-DOF (degree of freedom) magnetic bearing with vernier tilting capacity to perform dual-stage stabilization for the LOS of the suspended optical instrument. Compared with traditional dual-stage system, maglev dual-stage system exhibits different characteristics due to the negative position stiffness of the magnetic forces, which introduces additional coupling in the dual stage control system. In this paper, the coupling effect on the system performance is addressed based on frequency-domain analysis, including disturbance rejection, fine stage saturation and coarse stage structural resonance suppression. The difference between various control strategies is also discussed, including pile-up(PU), stabilize-follow (SF) and stabilize-compensate (SC). A number of principles for the design of a maglev dual stage system are proposed. A general process is also suggested, which leads to a cost-effective design striking a balance between high performance and complexity. At last, a simulation example is presented to illustrate the arguments in the paper. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

New pentose dimers with bicyclic moieties from pretreated biomass

DEFF Research Database (Denmark)

Rasmussen, H.; Sørensen, Henrik Rokkjær; Tanner, David Ackland

2017-01-01

In lignocellulosic biorefinery processes involving enzyme catalysed reactions it is a challenge that enzyme inhibiting compounds are generated and liberated during pretreatment of the biomass. In this study the contribution to cellulase inhibition from xylooligosaccharides and newly discovered...... oligophenolic compounds from pilot scale pretreated wheat straw was assessed at two different pretreatment severities. An increase in severity of the pretreatment led to more oligophenol compounds and in turn the total overall cellulase inhibition increased. When the xylooligosaccharides were enzymatically...... degraded prior to cellulose hydrolysis, a relief in cellulase inhibition was observed, but some inhibition remained, suggesting that other components also played a role in inhibition. We propose that these components include dipentoses with bicyclic moieties and feruloylated tripentoses, because LC...

Impact analysis of different chemical pre-treatments on colour of apple discs during drying process

Directory of Open Access Journals (Sweden)

Jasmina Lukinac

2009-01-01

Full Text Available The main purpose of this study was to compare colour changes of chemically pre-treated dried apple discs. Changes were observed by chromameter in L*a*b* colour model by using Minolta chromameter CR-400 and by image analysis system in RGB colour model. Apple discs variety "Gold Rush" were pre-treated and dried in laboratory tray drier at drying temperature 70 °C and at airflow velocity of 1.5 ms-1. Different chemical pre-treatments were applied on apple discs (dipping in 0.5% ascorbic acid solution; 0.3% L–cysteine solution; 0.1% 4–hexyl resorcinol solution and 1% sodium metabisulphite solution. Mean values of colour parameters, colour changes and correlation coefficients for apple discs were calculated for both colour models. The analysis showed statistically significant influence of pre-treatment method on total colour changes for both chosen colour models of dried apples. Calculated correlation coefficient between colour changes for used models was found to be 0.894. According to colour characteristics the best results were achieved when samples were pre-treated with 0.5% ascorbic acid solution. According to calculated results it was found that image analysis method as well as colorimetric method can be used to observe the colour changes on dried apple discs.

Production system and harvesting stage influence on nitrate content and quality of butterhead lettuce

Directory of Open Access Journals (Sweden)

Siti Fairuz Yosoff

2015-01-01

Full Text Available Leafy vegetables such as lettuce grown under different production systems may accumulate different concentrations of nitrate which may reach to the levels potentially toxic to humans. Moreover, nitrate accumulation varies in various plant parts and physiological age of the plant. Therefore, to determine the effect of production system and harvesting stage on nitrate accumulation and quality of butterhead lettuce, a study was conducted considering two lettuce production systems namely hydroponic and organic, and four different harvesting stages such as 35, 38, 41 and 44 days after transplanting (DAT. The experimental design was complete randomized design (CRD with four replications. Hydroponic and organic systems performed similar in terms of yield, quality and nitrate content of butterhead lettuce. Delaying harvesting can not only increase yield but also can minimize nitrate accumulation and health hazard risk as well. Delay in harvesting stage may result in quality deterioration of lettuce and increased production cost. Thus, a compromise is necessary to consider 41 DAT as the optimum stage to harvest butterhead lettuce with significantly higher reduction of nitrate content in both outer adult leaf blades and young leaves of hydroponic lettuce. Fresh weight, firmness and color of butterhead lettuce at this stage were still acceptable.

Cervical cancer staging, pretreatment planning and surgical treatment in the Nordic countries - survey from the Surgical Subcommittee of the Nordic Society of Gynecological Oncology

DEFF Research Database (Denmark)

Fuglsang, Katrine; Haldorsen, Ingfrid S; Lundqvist, Elisabeth Avall

2018-01-01

INTRODUCTION: Cervical cancer patients in the Nordic countries are increasingly undergoing pretreatment imaging by ultrasound, magnetic resonance imaging (MRI), position emission tomography - computed tomography (PET-CT) or computed tomography, or sentinel lymph node (SLN) procedure. The present ...

Seventh edition (2010) of the AJCC/UICC staging system for gastric adenocarcinoma: is there room for improvement?

Science.gov (United States)

Patel, Manali I; Rhoads, Kim F; Ma, Yifei; Ford, James M; Visser, Brendan C; Kunz, Pamela L; Fisher, George A; Chang, Daniel T; Koong, Albert; Norton, Jeffrey A; Poultsides, George A

2013-05-01

The gastric cancer AJCC/UICC staging system recently underwent significant revisions, but studies on Asian patients have reported a lack of adequate discrimination between various consecutive stages. We sought to validate the new system on a U.S. population database. California Cancer Registry data linked to the Office of Statewide Health Planning and Development discharge abstracts were used to identify patients with gastric adenocarcinoma (esophagogastric junction and gastric cardia tumors excluded) who underwent curative-intent surgical resection in California from 2002 to 2006. AJCC/UICC stage was recalculated based on the latest seventh edition. Overall survival probabilities were calculated using the Kaplan-Meier method. Of 1905 patients analyzed, 54 % were males with a median age of 70 years. Median number of pathologically examined lymph nodes was 12 (range, 1-90); 40 % of patients received adjuvant chemotherapy, and 31 % received adjuvant radiotherapy. The seventh edition AJCC/UICC system did not distinguish outcome adequately between stages IB and IIA (P = 0.40), or IIB and IIIA (P = 0.34). By merging stage II into 1 category and moving T2N1 to stage IB and T2N2, T1N3 to stage IIIA, we propose a new grouping system with improved discriminatory ability In this first study validating the new seventh edition AJCC/UICC staging system for gastric cancer on a U.S. population with a relatively limited number of lymph nodes examined, we found stages IB and IIA, as well as IIB and IIIA to perform similarly. We propose a revised stage grouping for the AJCC/UICC staging system that better discriminates between outcomes.

Proposal for a new staging system for osteoradionecrosis of the mandible

NARCIS (Netherlands)

Karagozoglu, K.H.; Dekker, H.A.; Rietveld, D.; de Bree, R.; Schulten, E.A.J.M.; Kantola, S.; Forouzanfar, T.; van der Waal, I.

2014-01-01

A new staging system for osteoradionecrosis of the mandible has been retrospectively applied to a group of 31 patients. In this system clinicoradiographic signs and symptoms are incorporated in a simplified manner. For imaging purposes the use of plain radiographs such as periapical films and

Embryonic staging using a 3D virtual reality system

NARCIS (Netherlands)

C.M. Verwoerd-Dikkeboom (Christine); A.H.J. Koning (Anton); P.J. van der Spek (Peter); N. Exalto (Niek); R.P.M. Steegers-Theunissen (Régine)

2008-01-01

textabstractBACKGROUND: The aim of this study was to demonstrate that Carnegie Stages could be assigned to embryos visualized with a 3D virtual reality system. METHODS: We analysed 48 3D ultrasound scans of 19 IVF/ICSI pregnancies at 7-10 weeks' gestation. These datasets were visualized as 3D

Enhanced biogas production from penicillin bacterial residue by thermal-alkaline pretreatment

International Nuclear Information System (INIS)

Zhong, Weizhang; Li, Guixia; Gao, Yan; Li, Zaixing; Geng, Xiaoling; Li, Yubing; Yang, Jingliang; Zhou, Chonghui

2015-01-01

In this study, the orthogonal experimental design was used to determine the optimum conditions for the effect of thermal alkaline; pretreatment on the anaerobic digestion of penicillin bacterial residue. The biodegradability of the penicillin; bacterial residue was evaluated by biochemical methane potential tests in laboratory. The optimum values of temperature,; alkali concentration, pretreatment time and moisture content for the thermal-alkaline pretreatment were determined as; 70 °C, 6% (w/v), 30 min, and 85%, respectively. Thermal-alkaline pretreatment could significantly enhance the soluble; chemical oxygen demand solubilization, the suspended solid solubilization and the biodegradability. Biogas production; was enhanced by the thermal-alkaline pretreatment, probably as a result of the breakdown of cell walls and membranes of; micro-organisms, which may facilitate the contact between organic molecules and anaerobic microorganisms.; Keywords: penicillin bacterial residue; anaerobic digestion; biochemical methane potential tests; pretreatment

Two-stage commercial evaluation of engineering systems production projects for high-rise buildings

Science.gov (United States)

Bril, Aleksander; Kalinina, Olga; Levina, Anastasia

2018-03-01

The paper is devoted to the current and debatable problem of methodology of choosing the effective innovative enterprises for venture financing. A two-stage system of commercial innovation evaluation based on the UNIDO methodology is proposed. Engineering systems account for 25 to 40% of the cost of high-rise residential buildings. This proportion increases with the use of new construction technologies. Analysis of the construction market in Russia showed that the production of internal engineering systems elements based on innovative technologies has a growth trend. The production of simple elements is organized in small enterprises on the basis of new technologies. The most attractive for development is the use of venture financing of small innovative business. To improve the efficiency of these operations, the paper proposes a methodology for a two-stage evaluation of small business development projects. A two-stage system of commercial evaluation of innovative projects allows creating an information base for informed and coordinated decision-making on venture financing of enterprises that produce engineering systems elements for the construction business.

Two-stage commercial evaluation of engineering systems production projects for high-rise buildings

Directory of Open Access Journals (Sweden)

Bril Aleksander

2018-01-01

Full Text Available The paper is devoted to the current and debatable problem of methodology of choosing the effective innovative enterprises for venture financing. A two-stage system of commercial innovation evaluation based on the UNIDO methodology is proposed. Engineering systems account for 25 to 40% of the cost of high-rise residential buildings. This proportion increases with the use of new construction technologies. Analysis of the construction market in Russia showed that the production of internal engineering systems elements based on innovative technologies has a growth trend. The production of simple elements is organized in small enterprises on the basis of new technologies. The most attractive for development is the use of venture financing of small innovative business. To improve the efficiency of these operations, the paper proposes a methodology for a two-stage evaluation of small business development projects. A two-stage system of commercial evaluation of innovative projects allows creating an information base for informed and coordinated decision-making on venture financing of enterprises that produce engineering systems elements for the construction business.

Autohydrolysis pretreatment assessment in ethanol production from agave bagasse.

Science.gov (United States)

Rios-González, Leopoldo J; Morales-Martínez, Thelma K; Rodríguez-Flores, María F; Rodríguez-De la Garza, José A; Castillo-Quiroz, David; Castro-Montoya, Agustín J; Martinez, Alfredo

2017-10-01

The aim of the present work was to assess the autohydrolysis pretreatment of Agave tequilana bagasse for ethanol production. The pretreatment was conducted using a one-liter high pressure Parr reactor under different severity factors (SF) at a 1:6w/v ratio (solid:liquid) and 200rpm. The solids obtained under the selected autohydrolysis conditions were subjected to enzymatic hydrolysis with a commercial cellulase cocktail, and the enzymatic hydrolysate was fermented using Saccharomyces cerevisiae. The results obtained from the pretreatment process showed that the glucan content in the pretreated solid was mostly preserved, and an increase in the digestibility was observed for the case with a SF of 4.13 (190°C, 30min). Enzymatic hydrolysis of the pretreated solids showed a yield of 74.3%, with a glucose concentration of 126g/L, resulting in 65.26g/L of ethanol after 10h of fermentation, which represent a 98.4% conversion according to the theoretical ethanol yield value. Copyright © 2017 Elsevier Ltd. All rights reserved.

Optimization of hydrothermal pretreatment of wheat straw for production of bioethanol at low water consumption without addition of chemicals

DEFF Research Database (Denmark)

Østergaard Petersen, Mai; Larsen, Jan; Thomsen, Mette Hedegaard

2009-01-01

straw at pilot scale (up to 100 kg h(-1)) where six different pretreatment conditions have been investigated; all pretreatment conditions have been evaluated with regards to recovery of sugars after pretreatment (both C5 and C6) and convertibility of the cellulosic part of the fibers into ethanol......In the IBUS process (Integrated Biomass Utilization System) lignocellulosic biomass is converted into ethanol at high dry matter content without addition of chemicals and with a strong focus on energy efficiency. This study describes optimization of continuous hydrothermal pretreatment of wheat....... The experiments show that the optimum pretreatment parameters are 195 degrees C for 6-12 min. At these conditions, a total of app. 70% of the hemicellulose is recovered, 93-94% of the cellulose is recovered in the fibers and app. 89% of the cellulose in the fibers can be converted into ethanol by commercial...

Evaluation of surgical staging prior to combined modality therapy for esophageal cancer

International Nuclear Information System (INIS)

Suntharalingam, M.; Vines, E.; Echo, D. van; Greenwald, B.; Krasna, M.

1996-01-01

microscopic celiac node involvement while 2 had mediastinal disease. In total, 10 pts. (40%) had their clinical stage confirmed by surgical findings. Fifteen pts. (60%) had variation between these two staging methods. Among the 28 pts. taken to surgical resection, operative mortality was 15%. Additionally four patients did not undergo surgical resection (2 pts. unresectable, 1 pt. arrested during anesthesia, 1 unsuspected 5 mm metastatic liver lesion). Twenty-four pts. are available for analysis of response. Pathologic CR rate of 46% was observed using strict criteria including gross and microscopic evaluation and immunohistochemical staining. Seventeen percent had only microscopic disease remaining and 37% had a partial response with evidence of gross residual. To date only two pts. have shown evidence of local failure. Nine pts. (45%) have presented back with systemic spread. Ten pts. are alive NED, 3 AWD, 2 DNED, 5 DOD. Patients with positive celiac LN at laparoscopy did significantly worse than pts. whose celiac nodes were negative, with a 24-month actuarial disease free survival (DFS) of 0% vs 58% respectively (p=0.01). Patients surgically staged as T 2 had a significantly better outcome than T 3 patients (DFS 100% vs 43% at 18 months, p=0.04). CONCLUSIONS: In our experience surgical staging has proven to be a more accurate method of defining disease extent as compared to current noninvasive techniques. Pretreatment surgical staging should improve our ability to select patients for this aggressive treatment approach. A preliminary analysis of the information gathered at the time of staging has confirmed the predictive value of the current T stage system. This data also suggests that microscopic celiac lymph node involvement may represent the most significant predictor of a poor outcome

Pretreating wheat straw by the concentrated phosphoric acid plus hydrogen peroxide (PHP): Investigations on pretreatment conditions and structure changes.

Science.gov (United States)

Wang, Qing; Hu, Jinguang; Shen, Fei; Mei, Zili; Yang, Gang; Zhang, Yanzong; Hu, Yaodong; Zhang, Jing; Deng, Shihuai

2016-01-01

Wheat straw was pretreated by PHP (the concentrated H3PO4 plus H2O2) to clarify effects of temperature, time and H3PO4 proportion on hemicellulose removal, delignification, cellulose recovery and enzymatic digestibility. Overall, hemicellulose removal was intensified by PHP comparing to the concentrated H3PO4. Moreover, efficient delignification specially happened in PHP pretreatment. Hemicellulose removal and delignification by PHP positively responded to temperature and time. Increasing H3PO4 proportion in PHP can promote hemicellulose removal, however, decrease the delignification. Maximum hemicellulose removal and delignification were achieved at 100% and 83.7% by PHP. Enzymatic digestibility of PHP-pretreated wheat straw was greatly improved by increasing temperature, time and H3PO4 proportion, and complete hydrolysis can be achieved consequently. As temperature of 30-40°C, time of 2.0 h and H3PO4 proportion of 60% were employed, more than 92% cellulose was retained in the pretreated wheat straw, and 29.1-32.6g glucose can be harvested from 100g wheat straw. Copyright © 2015 Elsevier Ltd. All rights reserved.

Techno-economic comparison of centralized versus decentralized biorefineries for two alkaline pretreatment processes.

Science.gov (United States)

Stoklosa, Ryan J; Del Pilar Orjuela, Andrea; da Costa Sousa, Leonardo; Uppugundla, Nirmal; Williams, Daniel L; Dale, Bruce E; Hodge, David B; Balan, Venkatesh

2017-02-01

In this work, corn stover subjected to ammonia fiber expansion (AFEX™) 1 pretreatment or alkaline pre-extraction followed by hydrogen peroxide post-treatment (AHP pretreatment) were compared for their enzymatic hydrolysis yields over a range of solids loadings, enzymes loadings, and enzyme combinations. Process techno-economic models were compared for cellulosic ethanol production for a biorefinery that handles 2000tons per day of corn stover employing a centralized biorefinery approach with AHP or a de-centralized AFEX pretreatment followed by biomass densification feeding a centralized biorefinery. A techno-economic analysis (TEA) of these scenarios shows that the AFEX process resulted in the highest capital investment but also has the lowest minimum ethanol selling price (MESP) at $2.09/gal, primarily due to good energy integration and an efficient ammonia recovery system. The economics of AHP could be made more competitive if oxidant loadings were reduced and the alkali and sugar losses were also decreased. Copyright © 2016 Elsevier Ltd. All rights reserved.

Au/n-ZnO rectifying contact fabricated with hydrogen peroxide pretreatment