WorldWideScience

Sample records for pressing hiping conditions

  1. Oxide formation and precipitation behaviors on interface of F82H steel joints during HIPing and hot pressing

    International Nuclear Information System (INIS)

    Kishimoto, H.; Ono, T.; Sakasegawa, H.; Tanigawa, H.; Ando, M.; Shibayama, T.; Kohno, Y.; Kohyama, A.

    2013-01-01

    Joining technologies for F82H steels are important issues for the development of fusion energy. The hot isostatic pressing (HIP) method is appropriate for consolidating the first wall of the blanket because of the flexibility of the shape of HIPed products. The HIP method is planned for fabricating a complex-shaped first wall component with built-in cooling channels; thus, accumulation of studies of microstructural and mechanical property changes, especially lower toughness of the HIPed joints, is essential. Present research aims to reveal the microstructural evolution of F82H joints fabricated by the HIP method compared with joints fabricated by hot pressing, focusing on the formation of oxides on the interface. F82H joints were characterized using 1/3-scale Charpy V-notch impact test, transmission electron microscope, scanning electron microscope, and electron probe analysis to survey the microstructural characteristics of the interface

  2. Hot isostatically pressed (HIPed) thick-walled component for a pressurised water reactor (PWR) application

    International Nuclear Information System (INIS)

    Hookham, I.; Burdett, B.; Bridger, K.; Sulley, J.L.

    2009-01-01

    This paper presents the work conducted to justify and provide a quality assured HIPed thick-walled component for a PWR application; the component being designed and manufactured by Rolls-Royce. Rolls-Royce has previously published (ICAPP 08) its overall, staged approach to the introduction of powder HIPed components; starting with thin-walled, leak limited pressure boundaries, and culminating in the use of the powder HIPed process for thick walled components. This paper presents details specific to a thick walled pressure vessel component. Results are presented of non-destructive and destructive examinations of one of a batch of components. Mechanical testing and metallurgical examination results of sample material taken from different sections of the component are presented. A full range of test results is provided covering, as examples: tensile, Charpy impact and sensitization susceptibility. Differences in weldability between the HIPed and the previous forged form are also documented. (author)

  3. Microstructure and tensile properties of selectively laser-melted and of HIPed laser-melted Ti–6Al–4V

    International Nuclear Information System (INIS)

    Qiu, Chunlei; Adkins, Nicholas J.E.; Attallah, Moataz M.

    2013-01-01

    Ti–6Al–4V samples have been prepared by selective laser melting (SLM) with varied processing conditions. Some of the samples were stress-relieved or hot isostatically pressed (HIPed). The microstructures of all samples were characterised using optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) and the tensile properties measured before and after HIPing. It was found that the porosity level generally decreased with increase of laser power and laser scanning speed. Horizontally built samples were found to have a higher level of porosity than vertically built samples. The as-fabricated microstructure was dominated by columnar grains and martensites. HIPing closed the majority of the pores and also fully transformed the martensite into α and β phases. The as-fabricated microstructure exhibits very high tensile strengths but poor ductility with elongation generally smaller than 10%. The horizontally built samples show even lower elongation than vertically built samples. HIPing considerably improved ductility but led to a reduction in strength. With HIPing, the SLMed samples were found to show tensile properties comparable with those thermomechanically processed and annealed samples

  4. Hot Isostatic Press (HIP) vitrification of radwaste concretes

    International Nuclear Information System (INIS)

    Siemer, D.D.; Scheetz, B.; Gougar, M.L.D.

    1995-01-01

    Properly formulated and properly ''canned'' radwaste concretes can be readily hot-isostatically-pressed (HIPed) into materials that exhibit performance equivalent to typical radwaste-type glasses. The HIPing conditions (temperature/pressure) required to turn a concrete waste form into a ''vitrified'' waste form are quite mild and therefore consistent with both safety and high productivity. This paper describes the process and its products with reference to its potential application to Idaho Chemical Processing Plant (ICPP) reprocessing wastes

  5. RELATIONSHIP BETWEEN COMPACTING PRESSURE AND CONDITIONS IN PRESSING CHAMBER DURING BIOMASS PRESSING

    Directory of Open Access Journals (Sweden)

    Peter Križan

    2016-02-01

    Full Text Available In this paper, we will present the impact of the conditions in pressing chambers during the pressing of wooden briquettes. The conditions in pressing chambers can significantly impact the resulting compacting pressure required for the pressing of briquettes. In the introduction, we show which parameters of the pressing chamber during pressing can impact the resulting compacting pressure. The experiment results which are shown in this paper described the detected impact of some important pressing chamber parameters. This experiment aims to detect the pressing chamber length impact and the impact of the way of pressing. By setting the pressing conditions, we will be able to achieve the suitable resulting compacting pressure with respect to the required final briquettes quality.

  6. A critical evaluation of HIPE data.

    LENUS (Irish Health Repository)

    O'Callaghan, A

    2012-01-01

    Resource allocation and planning of future services is dependent on current volumes, making it imperative that procedural data is accurately recorded. We sought to evaluate the effectiveness of the information gathered by the Hospital Inpatient Enquiry (HIPE) system in recording such activity. Five index vascular procedures (open\\/endovascular abdominal aneurysm repair, carotid endarterectomy, lower limb angioplasty\\/bypass) were chosen to reflect activity. The Economic and Social Research Institute (ESRI), and HIPE databases were interrogated to obtain the regional and hospital specific figures for the years 2005, 2006 and 2009, and then compared with the prospective vascular database in St James\\'s hospital. Data for 2006 (the most recent year available) shows significant discrepancies between the HIPE and vascular database figures for St James\\'s hospital. The HIPE and database figures respectively for; open aneurysm 13\\/30 (-50%), endovascular aneurysm 39\\/31 (+25%), carotid 62\\/48 (+29%), angioplasty 242\\/111 (+100%) and bypass 24\\/10 (+100%) These inaccuracies are likely to be magnified on a regional and national level when pooling data.

  7. Characterization of 316L(N)-IG SS joint produced by hot isostatic pressing technique

    International Nuclear Information System (INIS)

    Nakano, J.; Miwa, Y.; Tsukada, T.; Kikuchi, M.; Kita, S.; Nemoto, Y.; Tsuji, H.; Jitsukawa, S.

    2002-01-01

    Type 316L(N) stainless steel of the international thermonuclear experimental reactor grade (316L(N)-IG SS) is being considered for the first wall/blanket module. Hot isostatic pressing (HIP) technique is expected for the fabrication of the module. To evaluate the integrity and susceptibility to stress corrosion cracking (SCC) of HIPed 316L(N)-IG SS, tensile tests in vacuum and slow strain rate tests in high temperature water were performed. Specimen with the HIPed joint had similar tensile properties to specimens of 316L(N)-IG SS, and did not show susceptibility to SCC in oxygenated water at 423 K. Thermally sensitized specimen was low susceptible to SCC even in the creviced condition. It is concluded that the tensile properties of HIPed SS are as high as those of the base alloy and the HIP process caused no deleterious effects

  8. Incineration ashes conditioning by isostatic pressing and melting

    International Nuclear Information System (INIS)

    Jouan, A.; Ouvrier, N.; Teulon, F.

    1990-01-01

    Alpha-bearing solid incineration wastes are conditioned for two principal reasons: to enhance the quality of the finished product for long-term storage, and to reduce the total waste volume. Isostatic pressing parameters were defined using containers 36 mm in diameter; the physicochemical properties of the compacted ashes were determined with 140 mm diameter containers and industrial feasibility was demonstrated with a large (300 mm diameter) container. Two types of ashes were used: ashes fabricated at Marcoule (either in devices developed by the CEA for the MELOX project with a standard MELOX composition, or by direct incineration at COGEMA's UP1 plant) and fly ash from a domestic waste incinerator. A major engineering study was also undertaken to compare the three known ash containment processes: isostatic pressing, melting, and cement-resin matrix embedding. The flowsheet, operational chronology and control principles were detailed for each process, and a typical plant layout was defined to allow comparisons of both investment and operating costs

  9. FeCrAl and Zr alloys joined using hot isostatic pressing for fusion energy applications

    International Nuclear Information System (INIS)

    Park, Dong Jun; Kim, Hyun Gil; Park, Jeong Yong; Jung, Yang Il; Park, Jung Hwan; Koo, Yang Hyun

    2016-01-01

    Highlights: • FeCrAl and Zr alloys were successfully joined by hot isostatic pressing (HIP). • The thickness of diffusion layer increased with an increase in HIP temperature. • Significant inter-diffusion was observed for HIP at 1150 °C. • Maximum joint strength was achieved at HIP temperature of 700 °C. - Abstract: FeCrAl and Zr alloys were joined by a hot isostatic pressing (HIP) method for fusion energy applications. The optimum conditions for the joining process were studied. The HIP temperatures were varied from 700 to 1050 °C. The mechanical properties of the HIPed samples were evaluated by four-point bending and tensile tests. The FeCrAl and Zr alloys HIPed at 700 °C showed higher joint strength than the other samples. The joint strength decreased with an increase in the HIP temperature from 700 to 950 °C and significantly dropped at 1050 °C. Transmission electron microscopy, scanning electron microscopy, and optical microscopy were used to characterize the joints and interface region of the HIPed samples. The joints appeared to be tightly bonded and no intermetallic compounds or gaps were observed at the interface for HIP temperatures up to 950 °C. A diffusion layer formed at the interface and its thickness increased with the HIP temperature. HIP at 1050 °C, on the other hand, resulted in significant inter-diffusion and formation of brittle inter-metallic compounds at the interface.

  10. The influence of pressing conditions on SrFe12O19 nano-particles

    DEFF Research Database (Denmark)

    Mortensen, Anna; Stingaciu, Marian; Christensen, Mogens

    2015-01-01

    work the SrFe12O19 powder was made in an autoclave and was analysed by X-ray diffraction and Rietveld Refinement to determine particle size. The powder was pressed using Spark Plasma Syntering system at different conditions in order to investigate how the pressing conditions influence the magnetic...... properties. It was found, that pressing at 950oC leads to a much better alignment than pellets pressed at room temperature. Furthermore, ball milling seems to decrease the degree of alignment and thereby the magnetic remanence which leads to a lower energy product. The magnetization was characterized using...

  11. Experimental and Simulation Analysis of Hot Isostatic Pressing of Gas Atomized Stainless Steel 316L Powder Compacts

    International Nuclear Information System (INIS)

    Lin, Dongguo; Park, Seong Jin; Ha, Sangyul; Shin, Youngho; Park, Dong Yong; Chung, Sung Taek; Bollina, Ravi; See, Seongkyu

    2016-01-01

    In this work, both experimental and numerical studies were conducted to investigate the densification behavior of stainless steel 316L (STS 316L) powders during hot isostatic pressing (HIP), and to characterize the mechanical properties of HIPed specimens. The HIP experiments were conducted with gas atomized STS 316L powders with spherical particle shapes under controlled pressure and temperature conditions. The mechanical properties of HIPed samples were determined based on a series of tensile tests, and the results were compared to a reference STS 316L sample prepared by the conventional process, i.e., extrusion and annealing process. Corresponding microstructures before and after tensile tests were observed using scanning electron microscopy and their relationships to the mechanical properties were addressed. Furthermore, a finite element simulation based on the power-law creep model was carried out to predict the density distribution and overall shape change of the STS316L powder compact during HIP process, which agreed well with the experimental results.

  12. Experimental and Simulation Analysis of Hot Isostatic Pressing of Gas Atomized Stainless Steel 316L Powder Compacts

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Dongguo; Park, Seong Jin [Pohang University of Science and Technology, Pohang (Korea, Republic of); Ha, Sangyul [Samsung Electro-Mechanics, Suwon (Korea, Republic of); Shin, Youngho [Doosan Heavy Industries and Construction Co., Ltd., Changwon (Korea, Republic of); Park, Dong Yong [Korea Institute of Energy Research, Daejeon (Korea, Republic of); Chung, Sung Taek [CetaTech Inc., Sacheon (Korea, Republic of); Bollina, Ravi [Bahadurpally Jeedimetla, Hyderabad (India); See, Seongkyu [POSCO, Pohang (Korea, Republic of)

    2016-10-15

    In this work, both experimental and numerical studies were conducted to investigate the densification behavior of stainless steel 316L (STS 316L) powders during hot isostatic pressing (HIP), and to characterize the mechanical properties of HIPed specimens. The HIP experiments were conducted with gas atomized STS 316L powders with spherical particle shapes under controlled pressure and temperature conditions. The mechanical properties of HIPed samples were determined based on a series of tensile tests, and the results were compared to a reference STS 316L sample prepared by the conventional process, i.e., extrusion and annealing process. Corresponding microstructures before and after tensile tests were observed using scanning electron microscopy and their relationships to the mechanical properties were addressed. Furthermore, a finite element simulation based on the power-law creep model was carried out to predict the density distribution and overall shape change of the STS316L powder compact during HIP process, which agreed well with the experimental results.

  13. Microscopic characterizations of membrane electrode assemblies prepared under different hot-pressing conditions

    International Nuclear Information System (INIS)

    Liang, Z.X.; Zhao, T.S.; Xu, C.; Xu, J.B.

    2007-01-01

    The durability of the membrane electrode assembly (MEA) for direct methanol fuel cells (DMFCs) is one of the most critical issues to be addressed before widespread commercialization of the DMFC technology. In this work, we investigated the effect of the hot-pressing duration on the performance and durability of the MEA prepared by hot-pressing technique. It was found that the 60-min hot pressing at 135 deg. C under the pressure of 4.0 MPa yielded a significantly improved MEA durability than did the 3-min hot pressing (a typical duration in practice) under the same condition, but no substantial difference was found in the cell performance of the MEAs prepared with the two different hot-pressing durations. The reason why the hot-pressing duration had no significant effect on cell performance is explained based on X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FT-IR) characterizations of the changes in the physiochemical properties of MEAs and their constituent components, including the anode, cathode and Nafion membrane, before and after hot pressing with different durations

  14. Pore annihilation in a single-crystal nickel-base superalloy during hot isostatic pressing: Experiment and modelling

    International Nuclear Information System (INIS)

    Epishin, Alexander; Fedelich, Bernard; Link, Thomas; Feldmann, Titus; Svetlov, Igor L.

    2013-01-01

    Pore annihilation during hot isostatic pressing (HIP) was investigated in the single-crystal nickel-base superalloy CMSX-4 experimentally by interrupted HIP tests at 1288 °C/103 MPa. The kinetics of pore annihilation was determined by density measurement and quantitative metallography. Transmission electron microscopy of a HIPed specimen showed that the pores shrink via dislocation movement on octahedral glide planes. Theoretically pore closure under HIP condition was modelled by the finite element method using crystal plasticity and large strain theories. The modelling gives a similar kinetics of pore annihilation as observed experimentally, however somewhat higher annihilation rate

  15. Influences of hot-isostatic-pressing temperature on microstructure, tensile properties and tensile fracture mode of Inconel 718 powder compact

    International Nuclear Information System (INIS)

    Chang, Litao; Sun, Wenru; Cui, Yuyou; Yang, Rui

    2014-01-01

    Inconel 718 powders have been hot-isostatic-pressed (HIPed) at representative temperatures to investigate the variations in microstructure, tensile properties and tensile fracture mode of the powder compact. Microstructure of the powder compacts were characterized by optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and so on. The results showed that the interdendritic precipitates inherited from the powders were partially retained in the powder compacts when the powders were HIPed at or below 1210 °C but were eliminated when HIPed at and above 1260 °C. The grain size uniformity of the powder compacts first increases and then decreases with increasing HIPing temperature. Prior particle boundaries (PPBs) were observed in the powder compacts HIPed at and below 1260 °C but was eliminated when HIPed at 1275 °C. The PPBs were decorated with carbide particles, the amount of the carbide particles at the PPBs decreases with increasing HIPing temperature. Most of the PPBs were pinned by the carbide particles in the compacts HIPed at 1140 °C. When the HIPing temperature was increased to 1210 °C and 1260 °C, a large number of PPBs de-pinned and moved beyond the pinning carbide particles, leading to grain growth and leaving carbide particles at the site of the original PPBs within the new grains. With increasing HIPing temperature, the 0.2% yield strength of the powder compacts at 650 °C decreases, the tensile elongation increases, and the tensile fracture mode changed from inter-particle dominant fracture to fully dimple ductile fracture

  16. Influences of hot-isostatic-pressing temperature on microstructure, tensile properties and tensile fracture mode of Inconel 718 powder compact

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Litao [Institute of Metal Research, Chinese Academy of Sciences, Shenyang (China); University of Chinese Academy of Sciences, Beijing (China); Sun, Wenru; Cui, Yuyou [Institute of Metal Research, Chinese Academy of Sciences, Shenyang (China); Yang, Rui, E-mail: ryang@imr.ac.cn [Institute of Metal Research, Chinese Academy of Sciences, Shenyang (China)

    2014-04-01

    Inconel 718 powders have been hot-isostatic-pressed (HIPed) at representative temperatures to investigate the variations in microstructure, tensile properties and tensile fracture mode of the powder compact. Microstructure of the powder compacts were characterized by optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and so on. The results showed that the interdendritic precipitates inherited from the powders were partially retained in the powder compacts when the powders were HIPed at or below 1210 °C but were eliminated when HIPed at and above 1260 °C. The grain size uniformity of the powder compacts first increases and then decreases with increasing HIPing temperature. Prior particle boundaries (PPBs) were observed in the powder compacts HIPed at and below 1260 °C but was eliminated when HIPed at 1275 °C. The PPBs were decorated with carbide particles, the amount of the carbide particles at the PPBs decreases with increasing HIPing temperature. Most of the PPBs were pinned by the carbide particles in the compacts HIPed at 1140 °C. When the HIPing temperature was increased to 1210 °C and 1260 °C, a large number of PPBs de-pinned and moved beyond the pinning carbide particles, leading to grain growth and leaving carbide particles at the site of the original PPBs within the new grains. With increasing HIPing temperature, the 0.2% yield strength of the powder compacts at 650 °C decreases, the tensile elongation increases, and the tensile fracture mode changed from inter-particle dominant fracture to fully dimple ductile fracture.

  17. Muscular outputs during dynamic bench press under stable versus unstable conditions.

    Science.gov (United States)

    Koshida, Sentaro; Urabe, Yukio; Miyashita, Koji; Iwai, Kanzunori; Kagimori, Aya

    2008-09-01

    Previous studies have suggested that resistance training exercise under unstable conditions decreases the isometric force output, yet little is known about its influence on muscular outputs during dynamic movement. The objective of this study was to investigate the effect of an unstable condition on power, force, and velocity outputs during the bench press. Twenty male collegiate athletes (mean age, 21.3 +/- 1.5 years; mean height, 167.7 +/- 7.7 cm; mean weight, 75.9 +/- 17.5 kg) participated in this study. Each subject attempted 3 sets of single bench presses with 50% of 1 repetition maximum (1RM) under a stable condition with a flat bench and an unstable condition with a Swiss ball. Acceleration data were obtained with an accelerometer attached to the center of a barbell shaft, and peak outputs of power, force, and velocity were computed. Although significant loss of the peak outputs was found under the unstable condition (p velocity outputs, compared with previous findings. Such small reduction rates of muscular outputs may not compromise the training effect. Prospective studies are necessary to confirm whether the resistance training under an unstable condition permits the improvement of dynamic performance and trunk stability.

  18. Void formation in ODS EUROFER produced by hot isostatic pressing

    International Nuclear Information System (INIS)

    Ortega, Y.; Monge, M.A.; Castro, V. de; Munoz, A.; Leguey, T.; Pareja, R.

    2009-01-01

    Positron annihilation experiments were performed on oxide dispersion strengthened (ODS) and non-ODS EUROFER prepared by mechanical alloying and hot isostatic pressing. The results revealed the presence of small voids in these materials in the as-HIPed conditions. Their evolution under isochronal annealing experiments was investigated. The coincidence Doppler broadening spectra of ODS EUROFER exhibited a characteristic signature attributed to positron annihilation in Ar-decorated voids at the oxide particle/matrix interfaces. The variation of the positron annihilation parameters with the annealing temperature showed three stages: up to 623 K, between 823 and 1323 K, and above 1323 K. In the temperature range 823-1323 K void coarsening had effect. Above 1323 K some voids annealed out, but others, associated to oxide particles and small precipitates, survived to annealing at 1523 K. Transmission electron microscopy observations were also performed to verify the characteristics of the surviving defects after annealing at 1523 K.

  19. Void formation in ODS EUROFER produced by hot isostatic pressing

    Energy Technology Data Exchange (ETDEWEB)

    Ortega, Y. [Departamento de Fisica, Universidad Carlos III de Madrid, 28911 Leganes (Spain)], E-mail: yanicet@fis.ucm.es; Monge, M.A. [Departamento de Fisica, Universidad Carlos III de Madrid, 28911 Leganes (Spain); Castro, V. de [Department of Materials, University of Oxford, Oxford OX1 3PH (United Kingdom); Munoz, A.; Leguey, T.; Pareja, R. [Departamento de Fisica, Universidad Carlos III de Madrid, 28911 Leganes (Spain)

    2009-04-30

    Positron annihilation experiments were performed on oxide dispersion strengthened (ODS) and non-ODS EUROFER prepared by mechanical alloying and hot isostatic pressing. The results revealed the presence of small voids in these materials in the as-HIPed conditions. Their evolution under isochronal annealing experiments was investigated. The coincidence Doppler broadening spectra of ODS EUROFER exhibited a characteristic signature attributed to positron annihilation in Ar-decorated voids at the oxide particle/matrix interfaces. The variation of the positron annihilation parameters with the annealing temperature showed three stages: up to 623 K, between 823 and 1323 K, and above 1323 K. In the temperature range 823-1323 K void coarsening had effect. Above 1323 K some voids annealed out, but others, associated to oxide particles and small precipitates, survived to annealing at 1523 K. Transmission electron microscopy observations were also performed to verify the characteristics of the surviving defects after annealing at 1523 K.

  20. Modelling and computer simulation for the manufacture by powder HIPing of Blanket Shield components for ITER

    International Nuclear Information System (INIS)

    Gillia, O.; Bucci, Ph.; Vidotto, F.; Leibold, J.-M.; Boireau, B.; Boudot, C.; Cottin, A.; Lorenzetto, P.; Jacquinot, F.

    2006-01-01

    In components of blanket modules for ITER, intricate cooling networks are needed in order to evacuate all heat coming from the plasma. Hot Isostatic Pressing (HIPing) technology is a very convenient method to produce near net shape components with complex cooling network through massive stainless steel parts by bonding together tubes inserted in grooves machined in bulk stainless steel. Powder is often included in the process so as to release difficulties arising with gaps closure between tube and solid part or between several solid parts. In the mean time, it releases the machining precision needed on the parts to assemble before HIP. However, inserting powder in the assembly means densification, i.e. volume change of powder during the HIP cycle. This leads to global and local shape changes of HIPed parts. In order to control the deformations, modelling and computer simulation are used. This modelling and computer simulation work has been done in support to the fabrication of a shield prototype for the ITER blanket. Problems such as global bending of the whole part and deformations of tubes in their powder bed are addressed. It is important that the part does not bend too much. It is important as well to have circular tube shape after HIP, firstly in order to avoid their rupture during HIP but also because non destructive ultrasonic examination is needed to check the quality of the densification and bonding between tube and powder or solid parts; the insertions of a probe in the tubes requires a minimal circular tube shape. For simulation purposes, the behaviour of the different materials has to be modelled. Although the modelling of the massive stainless steel behaviour is not neglected, the most critical modelling is about power. For this study, a thorough investigation on the powder behaviour has been performed with some in-situ HIP dilatometry experiments and some interrupted HIP cycles on trial parts. These experiments have allowed the identification of a

  1. On the Mechanical Properties of HIPE Templated Macroporous Poly(dicyclopentadiene) Prepared with Low Surfactant Amounts

    Czech Academy of Sciences Publication Activity Database

    Kovačič, S.; Matsko, N.B.; Jeřábek, Karel; Krajnc, P.; Slugovc, Ch.

    2013-01-01

    Roč. 1, č. 3 (2013), s. 487-490 ISSN 2050-7488 Institutional support: RVO:67985858 Keywords : cellular structure * surfactant * polyHIPE chemistry Subject RIV: CI - Industrial Chemistry, Chemical Engineering

  2. Influence of heat treatment on microstructure and tensile behavior of a hot isostatically pressed nickel-based superalloy

    Energy Technology Data Exchange (ETDEWEB)

    Qiu, Chunlei, E-mail: c.qiu@bham.ac.uk [School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom); Wu, Xinhua; Mei, Junfa [School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom); Andrews, Paul; Voice, Wayne [Rolls-Royce Plc, Derby DE24 8BJ (United Kingdom)

    2013-11-25

    Highlights: •Post-HIP heat treatment led to refined microstructure and improved tensile properties. •Deformation occurred mainly by forming stacking faults in γ′ at RT and elevated temperature. •Net-shape HIPed RR1000 failed in a transgranular fracture mode. -- Abstract: A nickel-based superalloy powder RR1000 has been hot isostatically pressed (HIPed) and heat treated to produce different microstructures. Microstructures were investigated using a scanning electron microscope (SEM). Tensile testing was performed at room temperature and 700 °C and the deformed samples were examined using SEM and transmission electron microscope (TEM). It was found that in the as-HIPed condition the microstructure consisted of coarse and irregular-shaped primary and secondary γ′ together with a low volume fraction of fine γ′ (<50 nm in diameter). Solution treatment below the γ′ solvus followed by air cooling resulted in the formation of finer cuboidal secondary γ′ (350–750 nm) and medium-sized spherical tertiary γ′ (100–200 nm). This led to an improvement of both the 0.2% yield strength and ultimate tensile strength. Ageing of the solution-treated or of the as-HIPed samples at 760 °C resulted in the precipitation of a high population of fine γ′ (around 50 nm) which further increased the strength. Within the resolution limit of the current TEM analysis, deformation at room temperature seemed to occur mainly by dislocations cutting through secondary γ′ and very fine γ′, accompanied by the formation of stacking faults within these precipitates; most of the medium-sized tertiary γ′ precipitates in solution-treated and aged samples were not cut through but were surrounded by dislocations. Deformation at 700 °C happened by dislocations cutting through γ′ precipitates and γ matrix, leading to the formation of extended stacking faults across both γ and γ′. It is suggested that the optimum treatment of the current powder superalloy is to

  3. Influence of heat treatment on microstructure and tensile behavior of a hot isostatically pressed nickel-based superalloy

    International Nuclear Information System (INIS)

    Qiu, Chunlei; Wu, Xinhua; Mei, Junfa; Andrews, Paul; Voice, Wayne

    2013-01-01

    Highlights: •Post-HIP heat treatment led to refined microstructure and improved tensile properties. •Deformation occurred mainly by forming stacking faults in γ′ at RT and elevated temperature. •Net-shape HIPed RR1000 failed in a transgranular fracture mode. -- Abstract: A nickel-based superalloy powder RR1000 has been hot isostatically pressed (HIPed) and heat treated to produce different microstructures. Microstructures were investigated using a scanning electron microscope (SEM). Tensile testing was performed at room temperature and 700 °C and the deformed samples were examined using SEM and transmission electron microscope (TEM). It was found that in the as-HIPed condition the microstructure consisted of coarse and irregular-shaped primary and secondary γ′ together with a low volume fraction of fine γ′ (<50 nm in diameter). Solution treatment below the γ′ solvus followed by air cooling resulted in the formation of finer cuboidal secondary γ′ (350–750 nm) and medium-sized spherical tertiary γ′ (100–200 nm). This led to an improvement of both the 0.2% yield strength and ultimate tensile strength. Ageing of the solution-treated or of the as-HIPed samples at 760 °C resulted in the precipitation of a high population of fine γ′ (around 50 nm) which further increased the strength. Within the resolution limit of the current TEM analysis, deformation at room temperature seemed to occur mainly by dislocations cutting through secondary γ′ and very fine γ′, accompanied by the formation of stacking faults within these precipitates; most of the medium-sized tertiary γ′ precipitates in solution-treated and aged samples were not cut through but were surrounded by dislocations. Deformation at 700 °C happened by dislocations cutting through γ′ precipitates and γ matrix, leading to the formation of extended stacking faults across both γ and γ′. It is suggested that the optimum treatment of the current powder superalloy is to

  4. Air Activated Self-Decontaminating Polydicyclopentadiene PolyHIPE Foams for Rapid Decontamination of Chemical Warfare Agents.

    Science.gov (United States)

    McGann, Christopher L; Daniels, Grant C; Giles, Spencer L; Balow, Robert B; Miranda-Zayas, Jorge L; Lundin, Jeffrey G; Wynne, James H

    2018-06-01

    The threat of chemical warfare agents (CWA) compels research into novel self-decontaminating materials (SDM) for the continued safety of first-responders, civilians, and active service personnel. The capacity to actively detoxify, as opposed to merely sequester, offending agents under typical environmental conditions defines the added value of SDMs in comparison to traditional adsorptive materials. Porous polymers, synthesized via the high internal phase emulsion (HIPE) templating, provide a facile fabrication method for materials with permeable open cellular structures that may serve in air filtration applications. PolyHIPEs comprising polydicyclopentadiene (polyDCPD) networks form stable hydroperoxide species following activation in air under ambient conditions. The hydroperoxide-containing polyDCPD materials react quickly with CWA simulants, Demeton-S and 2-chloroethyl ethyl sulfide, forming oxidation products as confirmed via gas chromatography mass spectrometry. The simplicity of the detoxification chemistry paired with the porous foam form factor presents an exciting opportunity for the development of self-decontaminating filter media. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Does HIPE data capture the complexity of stroke patients in an acute hospital setting?

    LENUS (Irish Health Repository)

    Clarke, B

    2010-01-01

    The Hospital Inpatient Enquiry (HIPE) system is currently used as a principle source of national data on discharges from acute hospitals. The Casemix Programme is used to calculate funding for patient care (HIPE activity and Specialty Costs Returns). Th coding is usually undertaken by clerical personnel. We were concerned that the medical complexity of our stroke patients was not captured by the process. The aims of this study were to compare activity coded by HIPE coding staff and medical staff in consecutive stroke patients discharged from the hospital. One hundred consecutive discharged patients with stroke as primary diagnosis were coded by clerical staff [usual practice] and by medical staff. We compared the coding and any differences. We calculated the financial comparison of subsequent differences in Diagnostic Related Groups (DRGs) and Relative Values (RVs). Clinician coded DRGs resulted in a higher assigned RV in 45 cases. The total RV value for HIPE using clerical coding was 595,268.94 euros and using medical coding was 725,252.16 euros. We conclude that medical input is useful in detailing the complications arising in stroke patients. We suggest that physicians should assist in the HIPE coding process in order to capture clinical complexity, so that funding can be appropriately assigned to manage these complex patients.

  6. Expanded Analysis of Hot Isostatic Pressed Iodine-Loaded Silver-Exchanged Mordenite

    Energy Technology Data Exchange (ETDEWEB)

    Jubin, R. T. [ORNL; Bruffey, S. H. [ORNL; Patton, K. K. [ORNL

    2014-09-30

    Reduced silver-exchanged mordenite (Ag0Z) is being evaluated as a potential material to control the release of radioactive iodine that is released during the reprocessing of used nuclear fuel into the plant off-gas streams. The purpose of this study was to determine if hot pressing could directly convert this iodine loaded sorbent into a waste form suitable for long-term disposition. The minimal pretreatment required for production of pressed pellets makes hot pressing a technically and economically desirable process. Initial scoping studies utilized hot uniaxial pressing (HUPing) to prepare samples of non-iodine-loaded reduced silver exchanged mordenite (Ag0Z). The resulting samples were very fragile due to the low pressure (~ 28 MPa) used. It was recommended that hot isostatic pressing (HIPing), performed at higher temperatures and pressures, be investigated. HIPing was carried out in two phases, with a third and final phase currently underway. Phase I evaluated the effects of pressure and temperature conditions on the manufacture of a pressed sample. The base material was an engineered form of silver zeolite. Six samples of Ag0Z and two samples of I-Ag0Z were pressed. It was found that HIPing produced a pressed pellet of high density. Analysis of each pressed pellet by scanning electron microscopy-energy dispersive spectrophotometry (SEM-EDS) and X-ray diffraction (XRD) demonstrated that under the conditions used for pressing, the majority of the material transforms into an amorphous structure. The only crystalline phase observed in the pressed Ag0Z material was SiO2. For the samples loaded with iodine (I-Ag0Z) iodine was present as AgI clusters at low temperatures, and transformed into AgIO4 at high temperatures. Surface mapping and EDS demonstrate segregation between silver iodide phases and silicon dioxide phases. Based on the results of the Phase I study, an expanded test matrix was developed to examine the effects of multiple source materials, compositional

  7. Influence of Forming Conditions on Springback in V-bending Process Using Servo Press

    Science.gov (United States)

    Abe, Shinya; Takahashi, Susumu

    To improve fuel efficiency, aluminum alloys and high tensile steel sheets are increasingly being applied to automotive body parts. However, it is difficult to obtain accurate dimensions of formed parts. Therefore, technologies for reducing springback for the part formed by press are strongly demanded. It is said that the die holding time at the bottom dead center of a servo press slide can affect springback. To clarify the forming mechanisms of this phenomenon, a V bending test with a servo press was performed. Aluminum alloys sheets are applied as specimens. The location of press slide was measured by linear scales. It was found that the movement of the slide in a slide motion program differs from the actual movement of the slide. It is important to confirm if the slide is located in the position specified in the program. In addition, a springback angle measurement system is proposed that uses laser displacement measurement apparatus. Because it avoids human error, the proposed measurement system is more accurate than the image processing method.

  8. Effect of standard heat treatment on the microstructure and mechanical properties of hot isostatically pressed superalloy inconel 718

    International Nuclear Information System (INIS)

    Rao, G. Appa; Kumar, Mahendra; Srinivas, M.; Sarma, D.S.

    2003-01-01

    Ni-Fe base superalloy, Inconel 718, was processed through powder metallurgy (P/M) hot isostatic pressing (HIP) route. In order to balance the strength and ductility, the HIPed material was given the standard heat treatment, viz. solution treatment at 980 deg. C for 1 h/water quenched (WQ) to room temperature and a two-step ageing treatment consisting of 720 deg. C for 8 h/furnace cooling (FC) at 55 deg. C h -1 to 620 deg. C and holding at 620 deg. C for 8 h before air cooling (AC) to room temperature. Optical microscopy and scanning electron microscopy (SEM) studies on the heat treated alloy have shown a homogeneous microstructure with fine grain size (25 μm) along with the presence of prior particle boundary (PPB) networks. Transmission electron microscopy (TEM) on the heat treated material has revealed the presence of oxides, MC carbides and δ-precipitates at the grain boundaries and a uniform precipitation of fine γ'' and γ' strengthening phases in the matrix. Tensile and stress rupture tests were performed on the heat treated material. While the yield strength (YS) and ultimate tensile strength (UTS) of the HIPed and heat treated alloy at room temperature and 650 deg. C were comparable to those of conventionally processed wrought IN 718, its ductility was lower. The stress rupture life of the HIPed alloy improved marginally due to heat treatment and met the minimum specification requirement of life hours but the rupture ductility was found to be inferior to that of the wrought material. The fractography of the failed samples has revealed the transgranular ductile mode of fracture in the as-solution treated alloy, while intergranular mode of failure with the decohesion of PPBs occurred more predominantly in the aged condition. This change of fracture mode with ageing treatment shows the ductility dependence on the relative strength of the matrix and PPBs. The TEM studies on the deformed alloy have revealed that the brittle oxides and carbides at the prior

  9. Une madone à Fukushima. La condition numérique du portrait de presse

    Directory of Open Access Journals (Sweden)

    Adeline Wrona

    2014-04-01

    Full Text Available Cet article analyse l’incidence des modes de circulation de l’image sur les pratiques de la photographie de presse. L’exemple choisi est celui d’une photographie qui représente une femme au milieu des décombres d’Ishinomaki, image achetée par l’Agence France-Presse (AFP à un quotidien japonais, au lendemain du Tsunami de mars 2011. Reprise en couverture de nombreux journaux occidentaux, recadrée autour de la figure féminine, initialement saisie en plan large, cette photographie devient un portrait, rapidement désigné comme « la madone des décombres ». En décrivant les facteurs techniques, commerciaux et éditoriaux qui structurent le secteur de la photographie de presse, l’article interroge la mondialisation des standards visuels. Il s’agit de comprendre comment des phénomènes de stéréotypie visuelle apparaissent en lien avec le fonctionnement du marché de l’image numérique : l’auteur procède donc à une observation des logiciels utilisés par les journalistes de l’AFP, combinée à une analyse sémiotique des formats, légendes, commentaires sur l’image. Il apparaît que la mondialisation de la photographie de presse, qui repose sur des « syndications » internationales, modifie aussi le statut du photographe d’agence. Alors que les normes journalistiques pour le journalisme agencier préconisent l’effacement de l’auteur, les transformations de la photographie d’Ishinomaki sont le déclenchement d’un feuilleton médiatique, sur les réseaux sociaux comme dans les magazines occidentaux, dont le photographe lui-même devient le héros. L’AFP publie une semaine après le Tsunami une dépêche concernant l’histoire de cette image, dévoilant toutes sortes d’informations qui demeurent ordinairement inconnues du public : prix de vente de la photographie, nom du chef du bureau chargé de la collecte d’informations en Asie, identité du photographe. Tous ces détails sont archivés sur

  10. Conditioning of cladding waste by press compaction and encapsulation in low-melting metal alloys

    International Nuclear Information System (INIS)

    Broothaerts, J.; Casteels, F.; Daniels, A.; De Regge, P.; Huys, D.; Leurs, A.

    1985-01-01

    The wetting of waste components by lead- and zinc-based alloys has been examined. The lead-based metals, either low or high alloyed, did not achieve acceptable wetting of fresh or oxidized zircaloy surfaces in the temperature range of 350 0 C to 550 0 C for exposure times up to 5 hours. The corrosion resistance of candidate embedment alloys on the basis of lead and zinc has been examined in two synthetic interstitial clay-waters, in direct contact with the clay, in a synthetic Asse brine solution and in contact with wet salt deposits. A unit compaction and embedment of active hulls at the scale of 50 to 100 g has been constructed and installed in a shielded cell. The compaction of irradiated hulls necessitates the use of slightly higher pressures to achieve the densification factor reached for inactive zircaloy. Batches of zircaloy and of stainless steel hulls have been compacted and embedded in lead alloys for leaching experiments using the natural water present in the Boom clay geological formation. A 3 meganewton compaction press has been installed in a mock-up shielded facility and its operation and maintenance by remote handling with telemanipulators has been studied

  11. Importance of Electrode Hot-Pressing Conditions for the Catalyst Performance of Proton Exchange Membrane Fuel Cells

    DEFF Research Database (Denmark)

    Andersen, Shuang Ma; Dhiman, Rajnish; Larsen, Mikkel Juul

    2015-01-01

    The catalyst performance in a proton exchange membrane fuel cell (PEMFC) depends on not only the choice of materials, but also on the electrode structure and in particular on the interface between the components. In this work, we demonstrate that the hot-pressing conditions used during electrode...... lamination have a great influence on the catalyst properties of a low-temperature PEMFC, especially on its durability. Lamination pressure, temperature and duration were systematically studied in relation to the electrochemical surface area, platinum dissolution, platinum particle size and electrode surface...

  12. Can common measures of core stability distinguish performance in a shoulder pressing task under stable and unstable conditions?

    Science.gov (United States)

    Keogh, Justin W L; Aickin, Sam E; Oldham, Anthony R H

    2010-02-01

    The primary purpose of this study was to determine whether a range of static core stability (CS) measures could distinguish shoulder press performance in unstable vs. stable conditions. Thirty resistance-trained men gave informed consent to participate in this study. One-repetition maximum strength (from 0.90), moderate (0.85 Core stability training (with or without a SB) may therefore only lead to significant improvements in functional dynamic performance if the postures, mode and velocity of contraction performed in training, are similar to the competitive tasks.

  13. Conditioning of cladding waste for long-term storage by press compaction and encapsulation in lead containment

    International Nuclear Information System (INIS)

    Regge, P. de

    1986-01-01

    The conditioning of compacted cladding waste has been based on the concept of a corrosion-resistant containment. The technique of press compaction in remote operation conditions has been demonstrated. Detailed specifications of the design of the container are discussed in the report. Testing procedures for the different containment parts have been developed and applied. The remote welding techniques of the stainless steel and lead-based parts of the containment have been investigated and reliable procedures are reported. A technique for remote leak-testing of welded containers is described. The report contains a series of pictures documenting the entire conditioning concept, starting from the dissolver basket at the reprocessing stage up to the final disposal container

  14. Novel portable press for synchrotron time-resolved 3-D micro-imagining under extreme conditions

    Energy Technology Data Exchange (ETDEWEB)

    Philippe, J.; Le Godec, Y., E-mail: yann.legodec@impmc.upmc.fr; Bergame, F.; Morand, M. [IMPMC, Université Pierre et Marie Curie, Paris (France); Mezouar, M.; Bauchau, S.; Alvarez-Murga, M. [European Synchrotron Radiation Facility, Grenoble (France); Perrillat, J. P. [Laboratoire de Géologie de Lyon, Université Claude Bernard Lyon1, Lyon (France); Bromiley, G.; Berg, M. [School of GeoSciences, University of Edinburgh, Edinburgh (United Kingdom); King, A.; Guignot, N.; Itié, J. P. [Synchrotron SOLEIL, St Aubin France (France); Atwood, Robert [Diamond Light Source Ltd., Harwell Science and Innovation Campus, Didcot (United Kingdom)

    2016-07-27

    Here we present the instrumental development to extend the synchrotron X-ray microtomography techniques to in situ studies under static compression (HP) or shear stress or the both conditions at high temperatures (HT). To achieve this, a new rotating tomography Paris-Edinburgh cell (rotoPEc) has been developed. This ultra-compact portable device, easily and successfully adapted to various multi-modal synchrotron experimental set-up at ESRF, SOLEIL and DIAMOND is explained in detail.

  15. Degradation rates of phorbol esters in Jatropha curcas L. oil and pressed seeds under different storage conditions.

    Science.gov (United States)

    Phasukarratchai, Naphatsarnan; Damrongsiri, Seelawut; Tongcumpou, Chantra

    2017-03-01

    Phorbol esters (PEs), found in Jatropha curcas crude oil (JCO) and J. curcas pressed seeds (JPS), are known as bioactive compounds in agricultural and pharmaceutical applications. The degradation rates of PEs in JCO and JPS under various conditions is important for the utilisation of PEs. Thus the objective of this study was to determine the PE degradation rates in JCO and JPS under different storage conditions. PE degradation rates were found to be first-order reactions. The slowest degradation rate was at 0.9 × 10 -3 d -1 for both JCO and JPS unexposed to light at 4 °C. Light intensity (1097 lx and 4690 lx, representing diffused sunlight and fluorescent lighting, respectively) and temperature (25 to 35 °C) were the significant degradation factors. Light exposure led to 280% to 380% higher degradation rates in JCO than in JPS due to light penetration through the transparent oil. Dried and sterilised JPS showed an 80% to 90% lower PE degradation rate than untreated JPS under all storage conditions since biodegradation was assembly limited. The PEs were unstable under the studied conditions, especially when exposed to light and room temperature. To protect against PE degradation, a material should be stored in a light-protected container and below 4 °C. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  16. Microstructural and Microhardness Evolution from Homogenization and Hot Isostatic Pressing on Selective Laser Melted Inconel 718: Structure, Texture, and Phases

    Directory of Open Access Journals (Sweden)

    Raiyan Seede

    2018-05-01

    Full Text Available In this work, the microstructure, texture, phases, and microhardness of 45° printed (with respect to the build direction homogenized, and hot isostatically pressed (HIP cylindrical IN718 specimens are investigated. Phase morphology, grain size, microhardness, and crystallographic texture at the bottom of each specimen differ from those of the top due to changes in cooling rate. High cooling rates during the printing process generated a columnar grain structure parallel to the building direction in the as-printed condition with a texture transition from (001 orientation at the bottom of the specimen to (111 orientation towards the specimen top based on EBSD analysis. A mixed columnar and equiaxed grain structure associated with about a 15% reduction in texture is achieved after homogenization treatment. HIP treatment caused significant grain coarsening, and engendered equiaxed grains with an average diameter of 154.8 µm. These treatments promoted the growth of δ-phase (Ni3Nb and MC-type brittle (Ti, NbC carbides at grain boundaries. Laves phase (Fe2Nb was also observed in the as-printed and homogenized specimens. Ostwald ripening of (Ti, NbC carbides caused excessive grain growth at the bottom of the HIPed IN718 specimens, while smaller grains were observed at their top. Microhardness in the as-fabricated specimens was 236.9 HV and increased in the homogenized specimens by 19.3% to 282.6 HV due to more even distribution of secondary precipitates, and the nucleation of smaller grains. A 36.1% reduction in microhardness to 180.5 HV was found in the HIPed condition due to   γ ″ phase dissolution and differences in grain morphology.

  17. High-Surface-Area, Emulsion-Templated Carbon Foams by Activation of polyHIPEs Derived from Pickering Emulsions

    Directory of Open Access Journals (Sweden)

    Robert T. Woodward

    2016-09-01

    Full Text Available Carbon foams displaying hierarchical porosity and excellent surface areas of >1400 m2/g can be produced by the activation of macroporous poly(divinylbenzene. Poly(divinylbenzene was synthesized from the polymerization of the continuous, but minority, phase of a simple high internal phase Pickering emulsion. By the addition of KOH, chemical activation of the materials is induced during carbonization, producing Pickering-emulsion-templated carbon foams, or carboHIPEs, with tailorable macropore diameters and surface areas almost triple that of those previously reported. The retention of the customizable, macroporous open-cell structure of the poly(divinylbenzene precursor and the production of a large degree of microporosity during activation leads to tailorable carboHIPEs with excellent surface areas.

  18. Hot-pressed geopolymer

    DEFF Research Database (Denmark)

    Ranjbar, Navid; Mehrali, Mohammad; Maheri, Mahmoud R.

    2017-01-01

    This research explores the use of simultaneous heating and pressing techniques in order to enhance the mechanical properties of fly ash (FA) based geopolymer under relatively low temperature conditions to ensure minimum-porosity. Four effective parameters of pressing force, alkali activator...

  19. High temperature mechanical performance of a hot isostatically pressed silicon nitride

    Energy Technology Data Exchange (ETDEWEB)

    Wereszczak, A.A.; Ferber, M.K.; Jenkins, M.G.; Lin, C.K.J. [and others

    1996-01-01

    Silicon nitride ceramics are an attractive material of choice for designers and manufacturers of advanced gas turbine engine components for many reasons. These materials typically have potentially high temperatures of usefulness (up to 1400{degrees}C), are chemically inert, have a relatively low specific gravity (important for inertial effects), and are good thermal conductors (i.e., resistant to thermal shock). In order for manufacturers to take advantage of these inherent properties of silicon nitride, the high-temperature mechanical performance of the material must first be characterized. The mechanical response of silicon nitride to static, dynamic, and cyclic conditions at elevated temperatures, along with reliable and representative data, is critical information that gas turbine engine designers and manufacturers require for the confident insertion of silicon nitride components into gas turbine engines. This final report describes the high-temperature mechanical characterization and analyses that were conducted on a candidate structural silicon nitride ceramic. The high-temperature strength, static fatigue (creep rupture), and dynamic and cyclic fatigue performance were characterized. The efforts put forth were part of Work Breakdown Structure Subelement 3.2.1, {open_quotes}Rotor Data Base Generation.{close_quotes} PY6 is comparable to other hot isostatically pressed (HIPed) silicon nitrides currently being considered for advanced gas turbine engine applications.

  20. Time-dependent rheoforging of A6061 aluminum alloy on a mechanical servo press and the effects of forming conditions on homogeneity of rheoforged samples

    Directory of Open Access Journals (Sweden)

    Meng Yi

    2015-01-01

    Full Text Available The solid and liquid phases in semisolid metal slurry exhibited different forming behaviours during deformation result in products with inhomogeneous quality. A6061 aluminum alloy was forged in the semisolid state on a mechanical servo press with the capability of multistage compression. To improve the homogeneity of rheoforged samples a time-dependent rheoforging strategy was designed. The distributions of the microstructure and mechanical properties the samples manufactured under various experimental conditions were investigated. The A6061 samples forged in the temperature range from 625 to 628 ∘C with a short holding time of 4 s and the upper die preheated to 300 ∘C exhibited a homogeneous microstructure and mechanical properties. The homogeneity of rheoforged samples resulted from the controllable free motion capability of the mechanical servo press and the adjustable fluidity and viscosity of the semisolid slurry.

  1. Critical Design Review of a Powder HIPed Shield Concept. Final Report for the contract EFDA/01-601

    International Nuclear Information System (INIS)

    Lind, Anders

    2002-05-01

    The Shield of the ITER Primary Wall Module Option A consists of a 316L Stainless Steel block with front and back side radially cooled through water headers. In order to avoid structural welds located in high irradiation fields or highly mechanically loaded, powder HIPing was proposed by the EU Home Team as a possible fabrication method. This choice was motivated by the good results obtained through an extensive R and D programme performed within Associations and Industries. However, this fabrication technique has some implications on the design of the component, which shall be considered from the very beginning to achieve good performance and low cost. A critical review was therefore needed to optimise the concept before the fabrication of a Shield prototype. The contractor, based on its own experience on powder HIP technology and on the support from appropriate industry, did check the fabrication feasibility of the proposed Shield concept. The concept was judged to be feasible to a combined powder/solid HIPing route. Some adjustments of the design were proposed. The price for producing one shield block in a series of 400 items was estimated to fall into the range 150,000 - 175,000 Euro/pc

  2. Comparative evaluation of electrical conductivity of hydroxyapatite ceramics densified through ramp and hold, spark plasma and post sinter Hot Isostatic Pressing routes

    Energy Technology Data Exchange (ETDEWEB)

    Buchi Suresh, M., E-mail: suresh@arci.res.in; Biswas, P.; Mahender, V.; Johnson, Roy, E-mail: royjohnson@arci.res.in

    2017-01-01

    Hydroxyapatite ceramics synthesized through sonochemical route were processed and densified through ramp & hold (R&H) and Spark Plasma Sintering (SPS) routes. The effect of processing route on the relative density and electrical conductivity were studied. Further, the samples were Hot Isostatically Pressed (HIP) under argon pressure at elevated temperature to further densify the sample. All these samples processed under different conditions were characterized by X-ray diffraction, Scanning Electron Microscopy and AC Conductivity. The samples have exhibited hydroxyapatite phase; however, microstructures exhibited distinctly different grain morphologies and grain sizes. AC impedance spectroscopic measurement was carried out on hydroxyapatite samples processed through different routes and the corresponding spectra were analyzed by the analogy to equivalent circuit involving resistors and capacitors. SPS sintered sample after HIPing has exhibited the highest conductivity. This can be attributed to the higher density in combination with finer grain sizes. Activation energy based on Arrhenius equation is calculated and the prominent conduction mechanism is proposed. - Highlights: • Hot Isostatic Pressing (HIP) of SPS and R&H processed samples has resulted into densities near to theoretical densities • No change in the crystal structure is observed in SPS and R&H samples before and after HIP treatment • SPS processed and HIP treated samples resulted into higher conductivities with smaller grain sizes and grain boundary area.

  3. Selection of micro-organisms and fermentation conditions of oil palm empty fruit bunch (EFB) and palm press fibre (PPF)

    International Nuclear Information System (INIS)

    Mat Rasol Awang; Hassan Hamdani Mutaat; Tamikazu Kume; Hitoshi Ito

    1998-01-01

    The selection of useful microorganisms was made by trial cultivation of various cellulolytic fungi on EFB and PPF. Several fermentation conditions were performed involving adjusting alkali treatment conditions, pH, changing media composition and preparation technique of solid culture media. Basic the preparation of the solid culture media was made by dissolving inorganic salts together with micro-nutrients and then added to the alkali treated EFB and PPF. In the cultivation of mushrooms, the preparation of solid culture media was adopted from mushroom growers technique. The criteria of a good degradation ability of fungi were evaluated based on the percentage of crude fibre degradation of EFB and PPF by fungi. The nutritional values of the products such as protein was also characterised

  4. Application of PolyHIPE Membrane with Tricaprylmethylammonium Chloride for Cr(VI) Ion Separation: Parameters and Mechanism of Transport Relating to the Pore Structure.

    Science.gov (United States)

    Chen, Jyh-Herng; Le, Thi Tuyet Mai; Hsu, Kai-Chung

    2018-03-02

    The structural characteristics of membrane support directly affect the performance of carrier facilitated transport membrane. A highly porous PolyHIPE impregnated with Aliquat 336 is proposed for Cr(VI) separation. PolyHIPE consisting of poly(styrene- co -2-ethylhexyl acrylate) copolymer crosslinked with divinylbenzene has the pore structure characteristic of large pore spaces interconnected with small window throats. The unique pore structure provides the membrane with high flux and stability. The experimental results indicate that the effective diffusion coefficient D* of Cr(VI) through Aliquat 336/PolyHIPE membrane is as high as 1.75 × 10 -11 m² s -1 . Transport study shows that the diffusion of Cr(VI) through Aliquat 336/PolyHIPE membrane can be attributed to the jumping transport mechanism. The hydraulic stability experiment shows that the membrane is quite stable, with recovery rates remaining at 95%, even after 10 consecutive cycles of operation. The separation study demonstrates the potential application of this new type of membrane for Cr(VI) recovery.

  5. Press Start

    Science.gov (United States)

    Harteveld, Casper

    This level sets the stage for the design philosophy called “Triadic Game Design” (TGD). This design philosophy can be summarized with the following sentence: it takes two to tango, but it takes three to design a meaningful game or a game with a purpose. Before the philosophy is further explained, this level will first delve into what is meant by a meaningful game or a game with a purpose. Many terms and definitions have seen the light and in this book I will specifically orient at digital games that aim to have an effect beyond the context of the game itself. Subsequently, a historical overview is given of the usage of games with a serious purpose which starts from the moment we human beings started to walk on our feet till our contemporary society. It turns out that we have been using games for all kinds of non-entertainment purposes for already quite a long time. With this introductory material in the back of our minds, I will explain the concept of TGD by means of a puzzle. After that, the protagonist of this book, the game Levee Patroller, is introduced. Based on the development of this game, the idea of TGD, which stresses to balance three different worlds, the worlds of Reality, Meaning, and Play, came into being. Interested? Then I suggest to quickly “press start!”

  6. Void formation in ODS EUROFER produced by hot isostatic pressing

    Energy Technology Data Exchange (ETDEWEB)

    Ortega, Y.; Monge, M.A.; Munoz, A.; Leguey, T.; Pareja, R. [Madrid Univ. Carlos-3, Dept. de Fisica (Spain); Castro, V. de [Oxford Univ., Dept. of Materials (United Kingdom)

    2007-07-01

    Full text of publication follows: An obstacle in the development of oxide dispersion strengthened (ODS) steels for structural applications in fusion reactors is the toughness lack of the material produced by powder metallurgy and consolidated by hot isostatic pressing (HIP). In particular, ODS EUROFER steel with Y{sub 2}O{sub 3} particles appears to exhibit poor impact properties. To asses the capabilities of this material, it is necessary elucidate if its failure is an inherent characteristic of the production process that can not be mitigated by normalizing and tempering treatments. In order to investigate this particular point, the evolution of the structural defects retained in the ODS material during isochronal annealing has been probed by positron annihilation spectroscopy. The present study has been performed on bail milled EUROFER powders consolidated by HIP, containing 0.25 wt % Y{sub 2}O{sub 3} and without Y{sub 2}O{sub 3}. For comparison, un-milled EUROFER powder consolidated under identical conditions, and as-received EUROFER97 plate produced by Boehler AG have been also investigated. Samples from these four materials were isochronally annealed for 90 min up to 1323 K. Materials produced from milled powders had a longer positron lifetime than the one produced from un-milled powder or the EUROFER plate. In the material containing Y{sub 2}O{sub 3}, i.e. in ODS EUROFER, annealing above 723 K produced a continuous increase in the mean positron lifetime <{tau}> up to reach a maximum value of 208 ps after annealing at 1223 K. A similar annealing behavior was observed for Y{sub 2}O{sub 3}-free milled EUROFER (milled EUROFER), but the <{tau}> value steeply changed from {approx}160 ps at 823 K to {approx}200 ps after annealing at 1023 K. Subsequent anneals above this temperature produced meaningless changes in <{tau}>. The <{tau}> increase in milled EUROFER was accompanied by the intensity increase of a lifetime component of {approx}360 ps that is characteristic

  7. A novel Fe–Cr–Nb matrix composite containing the TiB_2 neutron absorber synthesized by mechanical alloying and final hot isostatic pressing (HIP) in the Ti-tubing

    International Nuclear Information System (INIS)

    Litwa, Przemysław; Perkowski, Krzysztof; Zasada, Dariusz; Kobus, Izabela; Konopka, Gustaw; Czujko, Tomasz; Varin, Robert A.

    2016-01-01

    The Fe–Cr–Ti-Nb elemental powders were mechanically alloyed/ball milled with TiB_2 and a small quantity of Y_2O_3 ceramic to synthesize a novel Fe-based alloy-ceramic powder composite that could be processed by hot isostatic pressing (HIP) for a perceived potential application as a neutron absorber in nuclear reactors. After ball milling for the 30–80 h duration relatively uniform powders with micrometric sizes were produced. With increasing milling time a fraction of TiB_2 particles became covered with the much softer Fe-based alloy which resulted in the formation of a characteristic “core-mantel” structure. For the final HIP-ing process the mechanically alloyed powders were initially uniaxially pressed into rod-shaped compacts and then cold isostatically pressed (CIP-ed). Subsequently, the rod-shaped compacts were placed in the Ti-tubing and subjected to hot isostatic pressing (HIP) at 1150 °C/200 MPa pressure. The HIP-ing process resulted in the formation of the near-Ti and intermediate diffusional layers in the microstructure of HIP-ed samples which formed in accord with the Fe-Ti binary phase diagram. Those layers contain the phases such as α-Ti (HCP), the FeTi intermetallic and their hypo-eutectoid mixtures. In addition, needle-like particles were formed in both layers in accord with the Ti-B binary phase diagram. Nanohardness testing, using a Berkovich type diamond tip, shows that the nanohardness in the intermediate layer areas, corresponding to the composition of the hypo-eutectoid mixture of Ti-FeTi, equals 980.0 (±27.1) HV and correspondingly 1176.9 (±47.6) HV for the FeTi phase. The nanohardness in the sample's center in the areas with the fine mixture of Fe-based alloy and small TiB_2 particles equals 1048.3 (±201.8) HV. The average microhardness of samples HIP-ed from powders milled for 30 and 80 h is 588 HV and 733 HV, respectively. - Highlights: • A Fe–Cr–Nb-based composite with TiB_2 neutron absorbing ceramic was mechanically

  8. Press release

    CERN Multimedia

    Association du personnel

    2006-01-01

    Geneva, 26 April 2006 – In the framework of the current five-yearly review, the CERN Staff Association denounces a serious attack on employment conditions. Indeed, the Management of the Organization has announced that it will not raise salary levels, even though after-tax salaries in the reference sector (high-tech industry, following a decision by the Member States) in Switzerland are today on average 20% higher than those at CERN. With this decision, the ever-increasing gap between CERN and this comparator as well as other international organizations will not be reduced. In view of the apathy and deceit of the Management which reveals an obvious contempt for the efforts agreed to by the staff, a notice of strike action has been given for Friday 28 April 2006.

  9. Ready… set, flow: simple fabrication of microdroplet generators and their use in the synthesis of PolyHIPE microspheres

    International Nuclear Information System (INIS)

    Lapierre, Florian; Cameron, Neil R; Zhu, Yonggang

    2015-01-01

    During the last decade, research and development in microfluidic devices have grown significantly due to their wide variety of applications in physics, chemistry and biology. A specific category of microfluidic devices focuses on the generation of micro-emulsions that can be used, for example, as chemical and biological reactors to synthesize new materials and perform assays. However, the traditional fabrication process of such microfluidic devices involves the use of special instrumentations and clean room facilities. These steps are generally expensive, time consuming and require specific levels of expertise. In this article, an alternative method to fabricate robust microfluidic devices using conventional components and a new commercially available self-setting rubber is presented. Using this method, a cheap, reproducible and easy to manufacture microfluidic device has been developed for generating single and double emulsions in the range of 100s of µm with high throughput. One possible application of this device is demonstrated with the synthesis of highly porous polymer beads from a High Internal Phase Emulsion (HIPE). The fabricated microbeads could find potential application in 3D cell culture due to their high porosity (up to 95%) and pore size (from 5 to 30 µm). The process here presented offers great opportunities for chemists and biologists interested in synthesising new materials while minimizing time, costs and expertise in the development of microfluidic systems. (paper)

  10. Fundamental Aspects of Zeolite Waste Form Production by Hot Isostatic Pressing

    Energy Technology Data Exchange (ETDEWEB)

    Jubin, Robert Thomas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bruffey, Stephanie H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jordan, Jacob A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-02-01

    The direct conversion of iodine-bearing sorbents into a stable waste form is a research topic of interest to the US Department of Energy. The removal of volatile radioactive 129I from the off-gas of a nuclear fuel reprocessing facility will be necessary in order to comply with the regulatory requirements that apply to facilities sited within the United States (Jubin et al., 2012a), and any iodine-containing media or solid sorbents generated by this process would contain 129I and would be destined for eventual geological disposal. While recovery of iodine from some sorbents is possible, a method to directly convert iodineloaded sorbents to a durable waste form with little or no additional waste materials being formed and a potentially reduced volume would be beneficial. To this end, recent studies have investigated the conversion of iodine-loaded silver mordenite (I-AgZ) directly to a waste form by hot isostatic pressing (HIPing) (Bruffey and Jubin, 2015). Silver mordenite (AgZ), of the zeolite class of minerals, is under consideration for use in adsorbing iodine from nuclear reprocessing off-gas streams. Direct conversion of I-AgZ by HIPing may provide the following benefits: (1) a waste form of high density that is tolerant to high temperatures, (2) a waste form that is not significantly chemically hazardous, and (3) a robust conversion process that requires no pretreatment.

  11. Progress in hot pressing

    International Nuclear Information System (INIS)

    Brodhag, C.; Thevenot, F.

    1988-01-01

    An experimental technique is described to study hot pressing of ceramics under conditions of controlled temperature and pressure during both the heating and final sintering stages. This method gives a better control of the final microstructure of the material. Transformation mechanisms can be studied during initial heating stage (impurity degasing, reaction, phase transformation, mechanical behavior of intergranular phase...) using computer control and graphical data representations. Some examples will be given for different systems studied in our laboratory: B (α, β, amorphous), B 12 O 2 (reaction of B + B 2 O 3 ), Si 3 N 4 ( + additives), TiN, Al 2 O 3 + AlON,ZrC

  12. Distribution of dissolved green-house gases (CO2, CH4, N2O) in Lakes Edward and George: Results from the first field cruise of the HIPE project

    Science.gov (United States)

    Borges, Alberto V.; Morana, Cédric D. T.; Lambert, Thibault; Okello, William; Bouillon, Steven

    2017-04-01

    Inland waters (streams, rivers, lakes, reservoirs) are quantitatively important components of the global budgets of atmospheric emissions of long-lived greenhouse gases (GHGs) (CO2, CH4, N2O). Available data indicate that a very large fraction of CO2 and CH4 emissions from rivers and reservoirs occurs at tropical latitudes. Data on GHGs at tropical latitudes from lakes however are much more scarse, and the relative importance of emissions, in particular in Africa, remains to be determined. Large tropical lakes are net autotrophic (hence potentially sinks for atmospheric CO2) due generally low dissolved organic carbon concentrations, seasonally near constant light and temperature conditions, and generally deep water columns favourable for export of organic matter to depth. This sharply contrasts with their much better documented temperate and boreal counterparts, usually considered as CO2 sources to the atmosphere sustained by net heterotrophy. Here, we report a data-set of dissolved CO2, CH4, N2O obtained in October 2016 in Lakes Edward and George and adjacent streams and crater lakes in the frame of Belgian Science Policy (BELSPO) HIPE (Human impacts on ecosystem health and resources of Lake Edward, http://www.co2.ulg.ac.be/hipe/) project. Lake George and part of Lake Edward were sinks for atmospheric CO2 and N2O due to high primary production and denitrification in sediments, respectively, and modest sources of CH4 to the atmosphere. Sampled rivers and streams were oversaturated in CO2 and CH4 and close to atmospheric equilibrium with regards to N2O. Spatial variations within rivers and streams were related to elevation and vegetation characteristics on the catchments (savannah versus forest). Levels of CO2, CH4, and N2O were within the range of those we reported in other African rivers. Crater lakes acted as sinks for atmospheric CO2 and N2O but were extremely over-saturated in CH4, due to intense primary production sustained by cyanobacteria. These CH4 levels

  13. Treatment of zircaloy cladding hulls by isostatic pressing

    International Nuclear Information System (INIS)

    Tegman, R.; Burstroem, M.

    1984-12-01

    A method for the treatment of Zircaloy fuel hulls is proposed. It involves hot isostatic pressing (HIP) for making large, completely densified metallic bodies of the waste. The hulls are packed into a bellows-shaped container of steel. On packing the fuel hulls give a filling factor of only 14%, which is too low for non-deformable compaction in a normal container, but by using a belloped container, a non-deformable compaction can be obtained without any pretreatment of the hulls. Fully dense and mechanically strong blocks of Zircaloy can be fabricated by holding them at temperatures of around 1000 degrees C for three hours. It is also feasible to incorporate the other metallic parts of the fuel bundle, such as top and bottom tie plates and spacers, in the pressing. The HIP-densified hulls provide an effective means of self-containment of radioactive waste due to the excellent corrosion resistance of Zircaloy. A waste loading factor of close to 100% can be realized. Futher, a volume reduction factor of 7 and a surface reduction factor of aout 250 for a 1-ton canister can be achieved. Equilibrium calculations have shown that tritium present in the hulls can quantitatively be contained in the HIPed block. A study has been made of a possible process for industrilscale use. (Author)

  14. Measurement of porosity in a composite high explosive as a function of pressing conditions by ultra-small-angle neutron scattering with contrast variation

    Energy Technology Data Exchange (ETDEWEB)

    Mang, Joseph Thomas [Los Alamos National Laboratory; Hjelm, Rex P [Los Alamos National Laboratory; Francois, Elizabeth G [Los Alamos National Laboratory

    2009-01-01

    We have used ultra-small-angle neutron scattering (USANS) with contrast variation to measure the porosity (voids and binder-filled regions) in a composite high explosive, PBX 9501, formulated with a deuterated binder. Little is known about the microstructure of pressed PBX 9501 parts and thus how it is affected by processing. Here, we explore the effect of varying the pressing intensity on the PBX 9501 microstructure. Disk-shaped samples of PBX 9501 were die-pressed with applied pressures ranging between 10,000 and 29,000 psi at 90 C. Five samples were prepared at each pressure that differed in the fraction of deuterated binder, facilitating variation of the neutron scattering length density contrast ({Delta}{rho}) and thus, the resolution of microstructural details. The sample composition was determined by calculation of the Porod Invariant as a function of {Delta}{rho} and compared with compositional estimates obtained from the bulk sample density. Structural modeling of the USANS data, at different levels of contrast, assuming both spherical and cylindrical morphologies, allowed the mean size and size distribution of voids and binder-filled regions to be determined. A decrease in the mean diameter of binder-filled regions was found with increasing pressing intensity, while the mean void diameter showed no significant change.

  15. Hot-pressing steatite bodies

    International Nuclear Information System (INIS)

    Aparicio Arroyo, E.

    1967-01-01

    Requirements for some special nuclear engineering ceramic shapes are: big size, impervious, dimensional accuracy and good mechanical and dielectric properties. Limitations of te conventional methods and advantages of te hot pressing techniques for the manufacturing of these shapes are discussed. Hot pressing characteristics of a certain steatite powder are studied. Occurrence of an optimum densification temperature just above the tale decomposition range is found. Experimental data show that the height/diameter ratio of the specimen has no effect on the sintering conditions. Increasing darkness from the graphite mould is detected above the optimum temperature. The hot-pressed steatite is compared with a fired dry-pressed sample of the same composition. (Author) 13 refs

  16. News/Press Releases

    Data.gov (United States)

    Office of Personnel Management — A press release, news release, media release, press statement is written communication directed at members of the news media for the purpose of announcing programs...

  17. Reciprocating pellet press

    Science.gov (United States)

    Jones, Charles W.

    1981-04-07

    A machine for pressing loose powder into pellets using a series of reciprocating motions has an interchangeable punch and die as its only accurately machines parts. The machine reciprocates horizontally between powder receiving and pressing positions. It reciprocates vertically to press, strip and release a pellet.

  18. The Global University Press

    Science.gov (United States)

    Dougherty, Peter J.

    2012-01-01

    The modern world's understanding of American university press has long been shaped by university-press books. American university-press books are good international advertisements for the universities whose logos grace their spines. The growth of transnational scholarship and the expansion of digital communications networks are converging in ways…

  19. Effect of molybdenum addition on aluminium grain refined by titanium on its metallurgical and mechanical characteristics in the as cast condition and after pressing by the equal angular channel process

    International Nuclear Information System (INIS)

    Zaid, A. I. O.; Atieh, A. M.

    2013-01-01

    Aluminium and its alloys are versatile materials which are widely used in industrial and engineering applications due to their attractive characteristics. However, they solidify in columnar structure which tends to reduce their surface quality and mechanical strength. It is therefore, grain refined by grain refiners i.e. titanium or titanium+boron. The equal angular channel pressing, ECAP, process is a recent method for producing severe plastic deformation in materials. In this research work, the effect of addition of molybdenum either alone or in the presence of titanium to commercially pure aluminium on microstructure and mechanical behaviour is investigated in two conditions; first, in the as cast condition, and second after pressing by the ECAP process at room temperature. It was found that addition of Ti alone at a rate of 0.15 percentage weight to commercially pure Al resulted in grain refining of microstructure and a grain size of 91 meu m was obtained. However, after pressing by the ECAP process further refinement was achieved and the grain size was reduced to 18 meu m. Addition of Mo alone to aluminium at a rate of 0.1 percentage resulted in grain size of 76 meu m in the as cast condition and 32 meu m after pressing by the ECAP process. The combination of the two elements Ti and Mo together resulted in 48 meu m grain size in the as cast condition, compared to 40 meu m after pressing by the ECAP process. Furthermore, it was found that in the as cast condition: addition of Ti alone to Al resulted in enhancement of its mechanical behaviour by an increase of 5.2 percentage increase in its flow stress at 20 percentage true strain, whereas addition of Mo either alone or in the presence of Ti resulted in decrease of its flow stress at 20 percentage by 9 percentage and 5.6 percentage respectively. However, after pressing by ECAP: it was found that addition of Ti or Mo either alone or together to Al resulted in increase of its flow stress at 20 percentage strain by

  20. Effect of molybdenum addition on aluminium grain refined by titanium on its metallurgical and mechanical characteristics in the as cast condition and after pressing by the equal angular channel process

    International Nuclear Information System (INIS)

    Zaid, A I O; Atieh, A M

    2014-01-01

    Aluminium and its alloys are versatile materials which are widely used in industrial and engineering applications due to their attractive characteristics. However, they solidify in columnar structure which tends to reduce their surface quality and mechanical strength. It is therefore, grain refined by grain refiners i.e. titanium or titanium+boron. The equal angular channel pressing, ECAP, process is a recent method for producing severe plastic deformation in materials. In this research work, the effect of addition of molybdenum either alone or in the presence of titanium to commercially pure aluminium on microstructure and mechanical behaviour is investigated in two conditions; first, in the as cast condition, and second after pressing by the ECAP process at room temperature. It was found that addition of Ti alone at a rate of 0.15% weight to commercially pure Al resulted in grain refining of microstructure and a grain size of 91μm was obtained. However, after pressing by the ECAP process further refinement was achieved and the grain size was reduced to 18μm. Addition of Mo alone to aluminium at a rate of 0.1% resulted in grain size of 76μm in the as cast condition and 32μm after pressing by the ECAP process. The combination of the two elements Ti and Mo together resulted in 48μm grain size in the as cast condition, compared to 40μm after pressing by the ECAP process. Furthermore, it was found that in the as cast condition: addition of Ti alone to Al resulted in enhancement of its mechanical behaviour by an increase of 5.2% increase in its flow stress at 20% true strain, whereas addition of Mo either alone or in the presence of Ti resulted in decrease of its flow stress at 20% by 9% and 5.6% respectively. However, after pressing by ECAP: it was found that addition of Ti or Mo either alone or together to Al resulted in increase of its flow stress at 20 % strain by the following percentages 5.49, 4.74 and 10.3% respectively

  1. Electro-Thermo-Mechanical Analysis of High-Power Press-Pack Insulated Gate Bipolar Transistors under Various Mechanical Clamping Conditions

    DEFF Research Database (Denmark)

    Hasmasan, Adrian Augustin; Busca, Cristian; Teodorescu, Remus

    2014-01-01

    With the continuously increasing demand for energy and the limited supply of fossil fuels, renewable power sources are becoming ever more important. Knowing that future energy demand will grow, manufacturers are increasing the size of new wind turbines (WTs) in order to reduce the cost of energy...... production. The reliability of the components has a large impact on the overall cost of a WT, and press-pack (PP) insulated gate bipolar transistors (IGBTs) could be a good solution for future multi-megawatt WTs because of advantages like high power density and reliability. When used in power converters, PP...

  2. WordPress Bible

    CERN Document Server

    Brazell, Aaron

    2010-01-01

    The WordPress Bible provides a complete and thorough guide to the largest self hosted blogging tool. This guide starts by covering the basics of WordPress such as installing and the principles of blogging, marketing and social media interaction, but then quickly ramps the reader up to more intermediate to advanced level topics such as plugins, WordPress Loop, themes and templates, custom fields, caching, security and more. The WordPress Bible is the only complete resource one needs to learning WordPress from beginning to end.

  3. Yb:Y2O3 transparent ceramics processed with hot isostatic pressing

    Science.gov (United States)

    Wang, Jun; Ma, Jie; Zhang, Jian; Liu, Peng; Luo, Dewei; Yin, Danlei; Tang, Dingyuan; Kong, Ling Bing

    2017-09-01

    Highly transparent 5 at.% Yb:Y2O3 ceramics were fabricated by using a combination method of vacuum sintering and hot isostatic pressing (HIP). Co-precipitated Yb:Y2O3 powders, with 1 at.% ZrO2 as the sintering aid, were used as the starting material. The Yb:Y2O3 ceramics, vacuum sintered at 1700 °C for 2 h and HIPed at 1775 °C for 4 h, exhibited small grain size of 1.9 μm and highly dense microstructure. In-line optical transmittance of the ceramics reached 83.4% and 78.9% at 2000 and 600 nm, respectively. As the ceramic slab was pumped by a fiber-coupled laser diode at about 940 nm, a maximum output power of 0.77 W at 1076 nm was achieved, with a corresponding slope efficiency of 10.6%.

  4. Transformation of Cs-IONSIV® into a ceramic wasteform by hot isostatic pressing

    Science.gov (United States)

    Chen, Tzu-Yu; Maddrell, Ewan R.; Hyatt, Neil C.; Gandy, Amy S.; Stennett, Martin C.; Hriljac, Joseph A.

    2018-01-01

    A simple method to directly convert Cs-exchanged IONSIV® IE-911 into a ceramic wasteform by hot isostatic pressing (1100 °C/190 MPa/2 hr) is presented. Two major Cs-containing phases, Cs2TiNb6O18 and Cs2ZrSi6O15, and a series of mixed oxides form. The microstructure and phase assemblage of the samples as a function of Cs content were examined using XRD, XRF, SEM and TEM/EDX. The chemical aqueous durability of the materials was investigated using the MCC-1 and PCT-B standard test methods. For HIPed Cs-IONSIV® samples, the MCC-1 normalised release rates of Cs were low rates are indicative of a safe long-term immobilisation matrix for Cs formed directly from spent IONSIV®. It was also demonstrated that the phase formation can be altered by adding Ti metal due to a controlled redox environment.

  5. Effect of equal-channel angular pressing and annealing conditions on the texture, microstructure, and deformability of an MA2-1 alloy

    Science.gov (United States)

    Serebryany, V. N.; Ivanova, T. M.; Kopylov, V. I.; Dobatkin, S. V.; Pozdnyakova, N. N.; Pimenov, V. A.; Savelova, T. I.

    2010-07-01

    Equal-channel angular pressing (ECAP) of am MA2-1 alloy according to routes A and Bc is used to study the possibility of increasing the low-temperature deformability of the alloy due to grain refinement and a change in its texture. To separate the grain refinement effect from the effect of texture on the deformability of the alloy, samples after ECAP are subjected to recrystallization annealing that provides grain growth to the grain size characteristic of the initial state (IS) of the alloy. Upon ECAP, the average grain size is found to decrease to 2-2.4 μm and the initial sharp axial texture changes substantially (it decomposes into several scattered orientations). The type of orientations and the degree of their scattering depend on the type of ECAP routes. The detected change in the texture is accompanied by an increase in the deformability parameters (normal plastic anisotropy coefficient R, strain-hardening exponent n, relative uniform elongation δu) determined upon tensile tests at 20°C for the states of the alloy formed in the IS-4A-4Bc and IS-4Ao-4BcO sequences. The experimental values of R agree with the values calculated in terms of the Taylor model of plastic deformation in the Bishop-Hill approximation using quantitative texture data in the form of orientation distribution function coefficients with allowance for the activation of prismatic slip, especially for ECAP routes 4Bc and 4BcO. When the simulation results, the Hall-Petch relation, and the generalized Schmid factors are taken into account, a correlation is detected between the deformability parameter, the Hall-Petch coefficient, and the ratio of the critical shear stresses on prismatic and basal planes.

  6. Influence of tools geometry and processing conditions on behavior of a difficult-to-work Al-Mg alloy during equal channel angular pressing

    Science.gov (United States)

    Comǎneci, Radu Ioachim; Nedelcu, Dumitru; Bujoreanu, Leandru Gheorghe

    2017-10-01

    Equal channel angular pressing (ECAP) is a well-established method for grain refinement in metallic materials by large shear plastic deformation, being the most promising and effective severe plastic deformation (SPD) technique. ECAP is a discontinuous process, so the billet removal implies a new development of the procedure: the new sample pushes out the previous sample. In resuming the process the head and the tail ends of the work piece which becomes strongly distorted and receiving different amount of strain have to be removed. Due to the path difference in material flow between upper and lower region of the outlet channel, a non-uniform strain and stress distribution across the width of the workpiece leaving the plastic deformation zone (PDZ) is achieved. A successful ECAP requires surpassing two obstacles: the necessary load level which directly affects tools and a favorable stress distribution so the material withstanding the accumulated strain of repeated deformation. Under back pressure (BP), materials have shown to be able to withstand more passes. As soon as the billet passes the PDZ along the bisector plane of the two channels, the compressive mean stress changes to tensile (leading to crack initiation), while in the presence of BP, a negative (compressive) stress is applied during the process. In this paper a comparative tridimensional finite element analysis (FEA) is performed to evaluate the behavior of a difficult-to-work Al-Mg alloy depending on tools geometry and process parameters. The results in terms of load level and strain distribution show the influence of the punch geometry and BP on the material behavior.

  7. WordPress Bible

    CERN Document Server

    Brazell, Aaron

    2011-01-01

    Get the latest word on the biggest self-hosted blogging tool on the marketWithin a week of the announcement of WordPress 3.0, it had been downloaded over a million times. Now you can get on the bandwagon of this popular open-source blogging tool with WordPress Bible, 2nd Edition. Whether you're a casual blogger or programming pro, this comprehensive guide covers the latest version of WordPress, from the basics through advanced application development. If you want to thoroughly learn WordPress, this is the book you need to succeed.Explores the principles of blogging, marketing, and social media

  8. Two layer powder pressing

    International Nuclear Information System (INIS)

    Schreiner, H.

    1979-01-01

    First, significance and advantages of sintered materials consisting of two layers are pointed out. By means of the two layer powder pressing technique metal powders are formed resulting in compacts with high accuracy of shape and mass. Attributes of basic powders, different filling methods and pressing techniques are discussed. The described technique is supposed to find further applications in the field of two layer compacts in the near future

  9. A novel Fe–Cr–Nb matrix composite containing the TiB{sub 2} neutron absorber synthesized by mechanical alloying and final hot isostatic pressing (HIP) in the Ti-tubing

    Energy Technology Data Exchange (ETDEWEB)

    Litwa, Przemysław [Department of Advanced Materials and Technologies, Military University of Technology, Kaliskiego 2, 00-908 Warsaw (Poland); Perkowski, Krzysztof [Department of Nanotechnology, Institute of Ceramics and Building Materials, Postępu 9, 02-676 Warsaw (Poland); Zasada, Dariusz [Department of Advanced Materials and Technologies, Military University of Technology, Kaliskiego 2, 00-908 Warsaw (Poland); Kobus, Izabela; Konopka, Gustaw [Department of Nanotechnology, Institute of Ceramics and Building Materials, Postępu 9, 02-676 Warsaw (Poland); Czujko, Tomasz [Department of Advanced Materials and Technologies, Military University of Technology, Kaliskiego 2, 00-908 Warsaw (Poland); Varin, Robert A., E-mail: robert.varin@uwaterloo.ca [Department of Mechanical and Mechatronics Engineering, University of Waterloo, 200 University Ave., Waterloo, ON N2L 3G1 (Canada)

    2016-07-25

    The Fe–Cr–Ti-Nb elemental powders were mechanically alloyed/ball milled with TiB{sub 2} and a small quantity of Y{sub 2}O{sub 3} ceramic to synthesize a novel Fe-based alloy-ceramic powder composite that could be processed by hot isostatic pressing (HIP) for a perceived potential application as a neutron absorber in nuclear reactors. After ball milling for the 30–80 h duration relatively uniform powders with micrometric sizes were produced. With increasing milling time a fraction of TiB{sub 2} particles became covered with the much softer Fe-based alloy which resulted in the formation of a characteristic “core-mantel” structure. For the final HIP-ing process the mechanically alloyed powders were initially uniaxially pressed into rod-shaped compacts and then cold isostatically pressed (CIP-ed). Subsequently, the rod-shaped compacts were placed in the Ti-tubing and subjected to hot isostatic pressing (HIP) at 1150 °C/200 MPa pressure. The HIP-ing process resulted in the formation of the near-Ti and intermediate diffusional layers in the microstructure of HIP-ed samples which formed in accord with the Fe-Ti binary phase diagram. Those layers contain the phases such as α-Ti (HCP), the FeTi intermetallic and their hypo-eutectoid mixtures. In addition, needle-like particles were formed in both layers in accord with the Ti-B binary phase diagram. Nanohardness testing, using a Berkovich type diamond tip, shows that the nanohardness in the intermediate layer areas, corresponding to the composition of the hypo-eutectoid mixture of Ti-FeTi, equals 980.0 (±27.1) HV and correspondingly 1176.9 (±47.6) HV for the FeTi phase. The nanohardness in the sample's center in the areas with the fine mixture of Fe-based alloy and small TiB{sub 2} particles equals 1048.3 (±201.8) HV. The average microhardness of samples HIP-ed from powders milled for 30 and 80 h is 588 HV and 733 HV, respectively. - Highlights: • A Fe–Cr–Nb-based composite with TiB{sub 2} neutron

  10. ALUMINUM BOX BUNDLING PRESS

    Directory of Open Access Journals (Sweden)

    Iosif DUMITRESCU

    2015-05-01

    Full Text Available In municipal solid waste, aluminum is the main nonferrous metal, approximately 80- 85% of the total nonferrous metals. The income per ton gained from aluminum recuperation is 20 times higher than from glass, steel boxes or paper recuperation. The object of this paper is the design of a 300 kN press for aluminum box bundling.

  11. DSS / Press Room

    Science.gov (United States)

    Defense Security Service, U.S. Department of Defense Site Map | A-Z Index | Facebook | Twitter Locations Press Room Organizational Structure Careers at DSS Doing Business with DSS Frequently Asked Classification System (NCCS) National Industrial Security System (NISS) ODAA Business Management System (OBMS

  12. OAS :: Press Releases

    Science.gov (United States)

    subscriptions Videos Photos Live Webcast Social Media Facebook @oasofficial Facebook Twitter @oas_official Social Media Facebook Twitter Newsletters Press and Communications Department Contact us at: +1 (202) 370 Rights Actions against Corruption C Children Civil Registry Civil Society Contact Us Culture Cyber

  13. bbPress complete

    CERN Document Server

    Wynne, Rhys

    2013-01-01

    A concise guide, written in an easy-to-follow format.This book is aimed at ambitious website or blog owners looking to add a forum to their site quickly and easily. Basic experience in WordPress and with managing a website is expected. Knowledge of HTML and PHP will be a bonus, though it isn't necessary.

  14. Myths About Press Freedom

    Directory of Open Access Journals (Sweden)

    Kaarle Nordenstreng

    2007-06-01

    Full Text Available This article intends to rectify three popular beliefs related to press freedom: (1 that the idea of a free marketplace of ideas with a self-righting truth belongs to original liberalism, (2 that UNESCO’s primary mission is to promote freedom of information, and (3 that the Universal Declaration of Human Rights provides legal safeguards for the media. These beliefs are shown, on the basis of the legacy of liberalism and documents of the international community, to be misleading myths. Instead of accurate readings of the idea of freedom, they serve as ideological positions which are harmful to democracy. The Millennium Declaration provides further proof that the international community has a much more balanced view of freedom of information than that typically held by media professionals. Therefore it is important to liberate the concept of press freedom from its ideological baggage.

  15. Inter-granular glassy phases in the low-CaO-doped HIPed Si{sub 3}N{sub 4} ceramics. A review

    Energy Technology Data Exchange (ETDEWEB)

    Gu, Hui [State Key Lab of High Performance Ceramics and Superfine Microstructures, Shanghai Inst. of Ceramics, Chinese Academy of Sciences, SH (China); Tanaka, Isao [Dept. of Materials Science and Engineering, Kyoto Univ. (Japan); Cannon, Rowland M. [Materials Science Div., Lawrence Berkeley National Lab., CA (United States); Pan, Xiaoqing [Dept. of Materials Science and Engineering, Michigan Univ., Ann Arbor (United States); Ruehle, Manfred [Max Planck Inst. for Metals Research, Stuttgart (Germany)

    2010-01-15

    This review outlines the essence of a progressive study on the glassy inter-granular film (IGF) in a model ceramic system, the low-CaO-doped HIPed high-purity Si{sub 3}N{sub 4}. This was initiated from the finding of a systematic variation of equilibrium IGF thickness following the dopant chemistry, manifesting its fundamental important to ceramic processing. By employing analytical transmission electron microscopy to measure the local chemistry in IGF, however, significant discrepancy was found between trends of local IGF chemistry and thickness. A stable IGF composition was revealed in this system, while a bi-level distribution of Ca segregation establishes a correspondence between the IGF structure and the surface crystallography. The detection of similar levels of nitrogen in IGF through the whole series further supports the presence of a rather stable IGF chemistry. After the saturation of dopants in the stable IGF, extra CaO was found to re-distribute in pockets by enrichment at tips, leading to a liquid phase separation with the Ca-rich phase wetting the entrance zone contacting IGF. The perspective for establishing a comprehensive correlation between the inter-granular phases and the bi-modal microstructure induced by faster growth of basal facets is briefly discussed to pave the way for future work. (orig.)

  16. Microstructure of HIPed and SPSed 9Cr-ODS steel and its effect on helium bubble formation

    International Nuclear Information System (INIS)

    Lu, Chenyang; Lu, Zheng; Xie, Rui; Liu, Chunming; Wang, Lumin

    2016-01-01

    Two 9Cr-ODS steels with the same nominal composition were consolidated by hot isostatic pressing (HIP, named COS-1) and spark plasma sintering (SPS, named COS-2). Helium ions were implanted into COS-1, COS-2 and non-ODS Eurofer 97 steels up at 673 K. Microstructures before and after helium ion implantations were carefully characterized. The results show a bimodal grain size distribution in COS-2 and a more uniform grain size distribution in COS-1. Nanoscale clusters of GP-zone type Y–Ti–O and Y_2Ti_2O_7 pyrochlore as well as large spinel Mn(Ti)Cr_2O_4 particles are all observed in the two ODS steels. The Y–Ti-enriched nano-oxides in COS-1 exhibit higher number density and smaller size than in COS-2. The Y–Ti-enriched nano-oxides in fine grains of COS-2 show higher number density and smaller size than that in coarse grains of COS-2. Nano-oxides effectively trap helium atoms and lead to the formation of high density and ultra-fine helium bubbles. - Highlights: • The microstructure changes of two ODS steels before and after helium ion implantation have been elucidated. • The mechanism of the microstructures of ODS steels under varied thermal mechanical processing paths have been explored. • The dependence of the size, density and distribution of helium bubbles on the specific microstructure features are explored.

  17. Microstructure of HIPed and SPSed 9Cr-ODS steel and its effect on helium bubble formation

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Chenyang [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), School of Material Science and Engineering, Northeastern University, Shenyang 110819, Liaoning (China); Department of Nuclear Engineering and Radiological Science, University of Michigan, Ann Arbor, MI, 48109 (United States); Lu, Zheng, E-mail: luz@atm.neu.edu.cn [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), School of Material Science and Engineering, Northeastern University, Shenyang 110819, Liaoning (China); Xie, Rui; Liu, Chunming [Key Laboratory for Anisotropy and Texture of Materials (Ministry of Education), School of Material Science and Engineering, Northeastern University, Shenyang 110819, Liaoning (China); Wang, Lumin, E-mail: lmwang@umich.edu [Department of Nuclear Engineering and Radiological Science, University of Michigan, Ann Arbor, MI, 48109 (United States)

    2016-06-15

    Two 9Cr-ODS steels with the same nominal composition were consolidated by hot isostatic pressing (HIP, named COS-1) and spark plasma sintering (SPS, named COS-2). Helium ions were implanted into COS-1, COS-2 and non-ODS Eurofer 97 steels up at 673 K. Microstructures before and after helium ion implantations were carefully characterized. The results show a bimodal grain size distribution in COS-2 and a more uniform grain size distribution in COS-1. Nanoscale clusters of GP-zone type Y–Ti–O and Y{sub 2}Ti{sub 2}O{sub 7} pyrochlore as well as large spinel Mn(Ti)Cr{sub 2}O{sub 4} particles are all observed in the two ODS steels. The Y–Ti-enriched nano-oxides in COS-1 exhibit higher number density and smaller size than in COS-2. The Y–Ti-enriched nano-oxides in fine grains of COS-2 show higher number density and smaller size than that in coarse grains of COS-2. Nano-oxides effectively trap helium atoms and lead to the formation of high density and ultra-fine helium bubbles. - Highlights: • The microstructure changes of two ODS steels before and after helium ion implantation have been elucidated. • The mechanism of the microstructures of ODS steels under varied thermal mechanical processing paths have been explored. • The dependence of the size, density and distribution of helium bubbles on the specific microstructure features are explored.

  18. ISS Expedition 08 Press Kit

    Data.gov (United States)

    National Aeronautics and Space Administration — Press kit for ISS mission Expedition 08 from 10/2003-04/2004. Press kits contain information about each mission overview, crew, mission timeline, benefits, and media...

  19. WordPress multisite administration

    CERN Document Server

    Longren, Tyler

    2013-01-01

    This is a simple, concise guide with a step-by-step approach, packed with screenshots and examples to set up and manage a network blog using WordPress.WordPress Multisite Administration is ideal for anyone wanting to familiarize themselves with WordPress Multisite. You'll need to know the basics about WordPress, and having at least a broad understanding of HTML, CSS, and PHP will help, but isn't required.

  20. Four Theories of the Press.

    Science.gov (United States)

    Siebert, Fred S.; And Others

    A systematic understanding of the press requires an understanding of the social and political structures within which the press operates. This book discusses four theories that have determined the kind of press the Western world has had: authoritarian, libertarian, socially responsible, and Soviet communist. Each chapter discusses press…

  1. Which Freedom of the Press?

    DEFF Research Database (Denmark)

    Rytter, Jens Elo

    2010-01-01

    The article surveys the historical and current meaning of "Freedom of the Press" in constitutional and human rights law. Two different conceptions exist, the narrow one defining freedom of the press as the freedom of every one to publish without prior restraint, the broader one defining it as a...... privileged freedom of the organised press to gather and report on information of public interest. These two conceptions have very different answers to the question of whether the press should enjoy some privilege to be exempt from ordinary legislation when such legislation restricts the access of the press to inform...

  2. WordPress for dummies

    CERN Document Server

    Sabin-Wilson, Lisa

    2014-01-01

    The bestselling WordPress guide, fully updated to cover the 2013 enhancements WordPress has millions of users, and this popular guide has sold more than 105,000 copies in its previous editions. With the newest releases of WordPress, author and WordPress expert Lisa Sabin-Wilson has completely updated the book to help you use and understand all the latest features. You'll learn about both the hosted WordPress.com version and the more flexible WordPress.org, which requires third-party hosting. Whether you're switching to WordPress from another blogging platform or just beginning to blog, you'll

  3. WordPress For Dummies

    CERN Document Server

    Sabin-Wilson, Lisa

    2011-01-01

    The bestselling guide to WordPress, fully updated to help you get your blog going! Millions of bloggers rely on WordPress, the popular, free blogging platform. This guide covers all the features and improvements in the most up-to-date version of WordPress. Whether you are switching to WordPress from another blogging platform or just starting your first blog, you'll find the advice in this friendly guide gets you up to speed on both the free-hosted WordPress.com version and WordPress.org, which requires the purchase of web hosting services, and figure out which version is best for you. You'll b

  4. Cyclic fatigue resistance of yttria-stabilized tetragonal zirconia polycrystals with hot isostatic press processing.

    Science.gov (United States)

    Koyama, Taku; Sato, Toru; Yoshinari, Masao

    2012-01-01

    This study investigated the influence of surface roughness and cyclic loading on fatigue resistance in Y-TZP subjected to hot isostatic pressing (HIP). Fifty Y-TZP cylinders 3.0 mm in diameter were divided into Group A (polished by centerless method; TZP-CP) or Group B (blasted and acid-etched: TZP-SB150E). Twenty five cp-titanium cylinders (Ti-SB150E) were used as a control. Static and cyclic tests were carried out according to ISO 14801. The cyclic fatigue test was performed in distilled water at 37°C. Surface morphology and roughness as well as crystal phase on the surfaces were also evaluated. Fracture force under the static test was 1,765N (TZP-CP), 1,220N (TZP-SB150E), and 850 N (yield force, Ti-SB150E). Fracture values under the cyclic test decreased to approximately 70% of those under the static tests. These results indicate that HIPed Y-TZP with a 3.0-mm diameter has sufficient durability for application to dental implants.

  5. WordPress Top Plugins

    CERN Document Server

    Corbin, Brandon

    2010-01-01

    Time flies when you're having fun. This is the right way to describe this WordPress Top Plugins book by Brandon Corbin. With real world examples and by showing you the perks of having these plugins installed on your websites, the author is all set to captivate your interest from start to end. Regardless of whether this is your first time working with WordPress, or you're a seasoned WordPress coding ninja, WordPress Top Plugins will walk you through finding and installing the best plugins for generating and sharing content, building communities and reader base, and generating real advertising r

  6. Indre spenninger og ytre press

    DEFF Research Database (Denmark)

    Ibsen, Bjarne

    2011-01-01

    Anmeldelse af bogen 'Norsk idrett. Indre spenninger og ytre press' redigeret af Dag Vidar Hanstad, Gunnar Breivik, Mari Kristin Sisjord og Hans B. Skaset og udgivet af forlaet akilles.......Anmeldelse af bogen 'Norsk idrett. Indre spenninger og ytre press' redigeret af Dag Vidar Hanstad, Gunnar Breivik, Mari Kristin Sisjord og Hans B. Skaset og udgivet af forlaet akilles....

  7. BuddyPress theme development

    CERN Document Server

    Lister, Tammie

    2013-01-01

    This book is a hands-on tutorial guide to using BuddyPress.This book is great for designers and developers who are looking to learn how to develop BuddyPress themes. It's assumed that the reader has some understanding of Wordpress and is familiar with CSS and HTML.

  8. Muscle activation when performing the chest press and shoulder press on a stable bench vs. a Swiss ball.

    Science.gov (United States)

    Uribe, Brandon P; Coburn, Jared W; Brown, Lee E; Judelson, Daniel A; Khamoui, Andy V; Nguyen, Diamond

    2010-04-01

    The aim of this study was to examine the effects of a stable surface (bench) vs. an unstable surface (Swiss ball) on muscle activation when performing the dumbbell chest press and shoulder press. Sixteen healthy men (24.19 +/- 2.17 years) performed 1 repetition maximum (1RM) tests for the chest press and shoulder press on a stable surface. A minimum of 48 hours post 1RM, subjects returned to perform 3 consecutive repetitions each of the chest press and shoulder press at 80% 1RM under 4 different randomized conditions (chest press on bench, chest press on Swiss ball, shoulder press on bench, shoulder press on Swiss ball). Electromyography was used to assess muscle activation of the anterior deltoid, pectoralis major, and rectus abdominus. The results revealed no significant difference in muscle activation between surface types for either exercise. This suggests that using an unstable surface neither improves nor impairs muscle activation under the current conditions. Coaches and other practitioners can expect similar muscle activation when using a Swiss ball vs. a bench.

  9. Head First WordPress

    CERN Document Server

    Siarto, Jeff

    2010-01-01

    Whether you're promoting your business or writing about your travel adventures, Head First WordPress will teach you not only how to make your blog look unique and attention-grabbing, but also how to dig into the more complex features of WordPress 3.0 to make your website work well, too. You'll learn how to move beyond the standard WordPress look and feel by customizing your blog with your own URL, templates, plugin functionality, and more. As you learn, you'll be working with real WordPress files: The book's website provides pre-fab WordPress themes to download and work with as you follow al

  10. Smashing WordPress Themes Making WordPress Beautiful

    CERN Document Server

    Hedengren, Thord Daniel

    2011-01-01

    The ultimate guide to WordPress Themes - one of the hottest topics on the web today WordPress is so much more than a blogging platform, and Smashing WordPress Themes teaches readers how to make it look any way they like - from a corporate site, to a photography gallery and moreWordPress is one of the hottest tools on the web today and is used by sites including The New York Times, Rolling Stone, flickr, CNN, NASA and of course Smashing MagazineBeautiful full colour throughout - web designers expect nothing lessSmashing Magazine will fully support this book by by promoting it through their webs

  11. Hot pressing of B4C/SiC composites

    International Nuclear Information System (INIS)

    Sahin, F.C.; Turhan, E.; Yesilcubuk, S.A.; Addemir, O.

    2005-01-01

    B 4 C/SiC ceramic composites containing 10-20-30 vol % SiC were prepared by hot pressing method. The effect of SiC addition and hot pressing temperature on sintering behaviour and mechanical properties of hot pressed composites were investigated. Microstructures of hot pressed samples were examined by SEM technique. Three different temperatures (2100 deg. C, 2200 deg. C and 2250 deg. C) were used to optimize hot pressing temperature applying 100 MPa pressure under argon atmosphere during the sintering procedure. The highest relative density of 98.44 % was obtained by hot pressing at 2250 deg. C. However, bending strengths of B 4 C/SiC composite samples were lower than monolithic B 4 C in all experimental conditions. (authors)

  12. ACTIVATED HOT PRESSING BEHAVIOR OF WC NANOPOWDERS

    Directory of Open Access Journals (Sweden)

    Edwin GEVORKYAN

    2010-06-01

    Full Text Available The questions of consolidation of nanopowders concerning hot compaction by pressing activated by electric current action are considered. Mechanisms of grain boundary creep-sliding which are sequentially prevalent in a forming of compacted structures under influence of temperature factor and in the presence of a direct electric heating are discussed. Structural-transformational sources and conditions of forming of high physical-mechanical properties of nanopowder refractory solid-state products are described.

  13. Science coverage and the press

    International Nuclear Information System (INIS)

    Hawkes, N.

    1992-01-01

    The writer, a journalist, summarizes the discussion of the Chilton Seminar, February 1992, and discusses the problems of bridging the incomprehension gap between scientists and lay readers of the press. (Author)

  14. Mathematical modelling of wet paper pressing

    NARCIS (Netherlands)

    Bežanovic, D.

    2005-01-01

    The aim of this project is to reduce energy costs in paper production by optimising the process in the press section of a paper machine. In this press section water is squeezed as it passes through the press nip. In a modern press section the moisture content of the sheet after three or four presses

  15. Reducing VOC Press Emission from OSB Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Gary D. McGinnis; Laura S. WIlliams; Amy E. Monte; Jagdish Rughani: Brett A. Niemi; Thomas M. Flicker

    2001-12-31

    Current regulations require industry to meet air emission standards with regard to particulates, volatile organic compounds (VOCs), hazardous air pollutants (HAPs) and other gases. One of many industries that will be affected by the new regulations is the wood composites industry. This industry generates VOCs, HAPs, and particulates mainly during the drying and pressing of wood. Current air treatment technologies for the industry are expensive to install and operate. As regulations become more stringent, treatment technologies will need to become more efficient and cost effective. The overall objective of this study is to evaluate the use of process conditions and chemical additives to reduce VOC/HAPs in air emitted from presses and dryers during the production of oriented strand board.

  16. Conférence de presse | Press Conference

    CERN Multimedia

    CERN. Geneva; Bejar Alonso, Isabel

    2018-01-01

    10:00-11:00 Conférence de presse en présence de Lucio Rossi, chef du projet LHC à Haute Luminosité et Isabel Bejar Alonso, chargée de la configuration, de la qualité et des ressources du projet LHC à Haute Luminosité.

  17. Investing in a Large Stretch Press

    Science.gov (United States)

    Choate, M.; Nealson, W.; Jay, G.; Buss, W.

    1986-01-01

    Press for forming large aluminum parts from plates provides substantial economies. Study assessed advantages and disadvantages of investing in large stretch-forming press, and also developed procurement specification for press.

  18. WordPress 3 Cookbook

    CERN Document Server

    Shreves, Ric

    2011-01-01

    This is a Packt Cookbook, which means it contains step-by-step instructions to achieve a particular goal or solve a particular problem. There are plenty of screenshots and explained practical tasks to make comprehension quick and easy. This book is not specifically for developers or programmers; rather it can be used by anyone who wants to get more out of their WordPress blog by following step-by-step instructions. A basic knowledge of PHP/XHTML/CSS/WordPress is desirable but not necessary.

  19. Law and the Student Press.

    Science.gov (United States)

    Stevens, George E.; Webster, John B.

    Court cases and legal decisions involving the student press in the late 1960s and early 1970s are brought together in this book in order to show how the law has been applied to school officials and student journalists in high school, college, and the underground. The ten chapters cover the following topics: censorship, libel, obscenity, contempt,…

  20. Local and international press digest

    CERN Multimedia

    2008-01-01

    The following are the top stories in the Maltese and the international press today. The Times gives prominence to the Prime Minister's flying visit to Geneva yesterday, where he signed a research cooperation agreement with CERN, the European nuclear research organisation.

  1. A new hot pressing technique

    International Nuclear Information System (INIS)

    Carcey, J.

    1975-01-01

    An original hot pressing method which may be applied to ceramics, metals, and refractory powders is described. The products obtained are fine grained polycristalline materials, with homogeneous structure, very high density, unstrained and of very large dimensions (several square meters). This process equally applies to composite materials including powders, fibers, etc.. [fr

  2. Forming of AHSS using Servo-Presses

    Science.gov (United States)

    Groseclose, Adam Richard

    Stamping of Advanced High Strength Steel (AHSS) alloys poses several challenges due to the material's higher strength and low formability compared to conventional steels and other problems such as (a) inconsistency of incoming material properties, (b) ductile fracture during forming, (c) higher contact pressure and temperature rise during forming, (d) higher die wear leading to reduced tool life, (e) higher forming load/press capacity, and (f) large springback leading to dimensional inaccuracy in the formed part. [Palaniswamy et. al., 2007]. The use of AHSS has been increasing steadily in automotive stamping. New AHSS alloys (TRIP, TWIP) may replace some of the Hot Stamping applications. Stamping of AHSS alloys, especially higher strength materials, 780 MPa and higher, present new challenges in obtaining good part definition (corner and fillet radii), formability (fracture and resulting scrap) and in reducing springback. Servo-drive presses, having the capability to have infinitely variable and adjustable ram speed and dwell at BDC, offer a potential improvement in quality, part definition, and springback reduction especially when the infinitely adjustable slide motion is used in combination with a CNC hydraulic cushion. Thus, it is desirable to establish a scientific/engineering basis for improving the stamping conditions in forming AHSS using a servo-drive press.

  3. A press for the theater

    Directory of Open Access Journals (Sweden)

    Luciana Penna França

    2017-12-01

    Full Text Available Understanding the history of the amateur theater at the end of the XIXth century and the beginning of the XXth is possible, largely, because of the newspapers dedicated to the “theatrical affairs”. Such publications are important for the quantity and the diversity, revealing not only the place occupied by the theater in the capital, but also for the recognition of the press as a means of disclosure of plays, public education and opinion, artist projection, etc, not to mention personal affairs and requests, and the exchange of favors among managers and journalists. Even more, the press production of the dramatic amateurs clubs demonstrate the understanding of its role in the dissemination of ways to act and think beyond the stage and in the everyday life.

  4. Pressing technology for large bottoms

    International Nuclear Information System (INIS)

    Jilek, L.

    1986-01-01

    The technology has been selected of a circular plate bent into the shape of a trough, for pressing bottoms of pressure vessels from a circular plate of large diameter. The initial sheet is first bent in the middle by heating with the edges remaining straight. These are then welded longitudinally by electroslag welding and the circular shape is flame cut. The result will be a plate with a straight surface in the middle with raised edges which may be pressed into the desired shape. In this manner it is also possible to press pressure vessel bottoms with tube couplings from plates which are thickened in the middle and drilled; additional welding is then eliminated. Deformation from heat treatment may be avoided by the use of a fixture in the shape of a ring with a groove into which is fixed the edge of the bottom. During hardening of the bottom it will be necessary to care for the withdrawal of vapours and gases which would hamper uniform cooling. Bottom hardening with the grill and the cupola downwards has been proven. Deformation which occurs during treatment may to a certain extent be removed by calibration which cannot, however, be made without special fixtures and instruments. (J.B.)

  5. Modularity of Pressing Tools for Screw Press Producing Solid Biofuels

    Directory of Open Access Journals (Sweden)

    Miloš Matúš

    2012-01-01

    Full Text Available This paper focuses on the development of the newly-patented structure of a screw briquetting machine for compacting biomass into a solid biofuel. The design of the machine is based on the results of a comprehensive study of the complicated process of biomass compaction. The patented structure meets two main goals: the elimination of axial forces, leading to increased lifetime of the bearings, and the new modular design of a pressing chamber and tools with their geometry based on the application of a mathematical model.

  6. Milestone Report - M3FT-15OR03120215 - Recommend HIP Conditions for AgZ

    Energy Technology Data Exchange (ETDEWEB)

    Bruffey, Stephanie H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jubin, Robert Thomas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-09-18

    The purpose of this study was to continue research to determine if HIPing could directly convert I-Ag0Z into a suitable waste form. Fiscal year (FY) 2015 work completed studies of Phase IIA, IIB, and IIC samples. Product consistency testing (PCT) of Phase IIA samples resulted in iodine release below detection limit for six of twelve samples. This is promising and indicates that a durable waste form may be produced through HIPing even if transformation of the zeolite to a distinct mineral phase does not occur. From PCT results of Phase IIA samples, it was determined that future pressing should be conducted at a temperature of 900°C. Phase IIC testing continued production of samples to examine the effects of multiple source materials, compositional variations, and an expanded temperature range. The density of each sample was determined and x-ray diffraction (XRD) patterns were obtained. In all cases, there was nothing in the XRD analyses to indicate the creation of any AgI-containing silicon phase; the samples were found to be largely amorphous.

  7. WordPress Website Development

    OpenAIRE

    Lassila, Joonas

    2016-01-01

    The aim of this Bachelor’s thesis was to develop a WordPress mobile-first style website for the customer, Pohjois-Suomen Pesis. The main purpose of the development was to learn website designing principles and create a responsive website for the mobile and desktop platforms. The development process began defining the requirements of the website and creating the requirements document. Then next step was learning how to design a website layout and to choose the colour scheme for the site. T...

  8. Smashing WordPress Beyond the Blog

    CERN Document Server

    Hedengren, Thord Daniel

    2012-01-01

    The ultimate guide to WordPress, from the world's most popular resource for web designers and developers As one of the hottest tools on the web today for creating a blog, WordPress has evolved to be much more that just a blogging platform and has been pushed beyond its original purpose. With this new edition of a perennially popular WordPress resource, Smashing Magazine offers you the information you need so you can maximize the potential and power of WordPress. WordPress expert Thord Daniel Hedengren takes you beyond the basic blog to show you how to leverage the capabilities of WordPress to

  9. Teach yourself visually WordPress

    CERN Document Server

    Majure, Janet

    2012-01-01

    Get your blog up and running with the latest version of WordPress WordPress is one of the most popular, easy-to-use blogging platforms and allows you to create a dynamic and engaging blog, even if you have no programming skills or experience. Ideal for the visual learner, Teach Yourself VISUALLY WordPress, Second Edition introduces you to the exciting possibilities of the newest version of WordPress and helps you get started, step by step, with creating and setting up a WordPress site. Author and experienced WordPress user Janet Majure shares advice, insight, and best practices for taking full

  10. Press releases — the new trend in science communication

    DEFF Research Database (Denmark)

    Autzen, Charlotte

    2014-01-01

    Scientific institutions have for a long time known the importance of framing and owning stories about science They also know the effective way of communicating science in a press release This is part of the institution’s public relations. Enhanced competition among research institutions has led...... to a buildup of communicative competences and professionalization of public relations inside the institutions and the press release has become an integrated part of science communication from these institutions. Changing working conditions in the media, where fewer people have to publish more, have made press...... releases from trustworthy scientific institutions into free and easily copied content for the editors. In this commentary I investigate and discuss the communicative ecosystem of the university press release. I especially take a close look at the role of the critical and independent science journalist...

  11. Prediction of Pressing Quality for Press-Fit Assembly Based on Press-Fit Curve and Maximum Press-Mounting Force

    Directory of Open Access Journals (Sweden)

    Bo You

    2015-01-01

    Full Text Available In order to predict pressing quality of precision press-fit assembly, press-fit curves and maximum press-mounting force of press-fit assemblies were investigated by finite element analysis (FEA. The analysis was based on a 3D Solidworks model using the real dimensions of the microparts and the subsequent FEA model that was built using ANSYS Workbench. The press-fit process could thus be simulated on the basis of static structure analysis. To verify the FEA results, experiments were carried out using a press-mounting apparatus. The results show that the press-fit curves obtained by FEA agree closely with the curves obtained using the experimental method. In addition, the maximum press-mounting force calculated by FEA agrees with that obtained by the experimental method, with the maximum deviation being 4.6%, a value that can be tolerated. The comparison shows that the press-fit curve and max press-mounting force calculated by FEA can be used for predicting the pressing quality during precision press-fit assembly.

  12. Material development in the SI{sub 3}N{sub 4} system using glass encapsulated Hip`ing. Final report, Phase 2: DOE/ORNL Ceramic Technology Project

    Energy Technology Data Exchange (ETDEWEB)

    Corbin, N.D.; Sundberg, G.J.; Siebein, K.N.; Willkens, C.A.; Pujari, V.K.; Rossi, G.A.; Hansen, J.S.; Chang, C.L.; Hammarstrom, J.L.

    1992-04-01

    This report covers a two-year program to develop fully dense Si{sub 3}N{sub 4} matrix SiC whisker composites with enhanced properties over monolithic Si{sub 3}N{sub 4} materials. The primary goal was to develop a composite with a fracture toughness > 10 MPa{radical}m, capable of using high pressure glass encapsulated HIP`ing. Coating methods were developed to apply thin (<150nm) stoichiometric BN layers to SiC whiskers and also to apply a dual coating of SiC over carbon to the whiskers. Fracture toughness of the composites was determined to increase as the quantity of whiskers (or elongated grains) with their axis perpendicular to the crack plane increased. Of the interface compositions evaluated in this effort, carbon was determined to be the most effective for increasing toughness. The highest toughnesses (6.8--7.0 MPa{radical}m) were obtained with uniaxially aligned carbon coated whiskers. There was no evidence of the carbon coating compromising the oxidation resistance of the composites at 1370{degree}C.

  13. Pellet presses for remote fuel fabrication

    International Nuclear Information System (INIS)

    Densley, P.J.

    1978-01-01

    Two types of mechanical presses are being tested from the remote operation and remote maintenance aspects. Results will be used to recommend the type of press and design considerations required for operation in a remotely operated and maintained process line

  14. Press to compress contaminated wastes drums

    International Nuclear Information System (INIS)

    Prevost, J.

    1993-01-01

    This patent describes a press for contaminated wastes drums pressing. The press is made of a structure comprising a base and an upper stringer bind to the base by vertical bearers, a compression system comprising a main cylinder and a ram, connected to the upper stringer

  15. IDEAL: ACADEMIC PRESS JOURNALS ONLINE

    CERN Multimedia

    The Library

    2001-01-01

    All Academic Press journals are available online to CERN users for a test period which will last until the end of July. The service 'IDEALIBRARY' includes 174 scientific journals that cover several domains, ranging from engineering to mathematics, computing and physics. Titles covered are among others 'Atomic Data and Nuclear Data Tables', 'Nuclear Data Sheets', 'Annals of Physics', 'Journal of Parallel and Distributed Computing'. Reference citations present in each article are linked to the corresponding full text, when the latter is published by a member of the CrossRef consortium (members are: Elsevier, APS, AIP and others). Therefore, the navigation between articles and references is uninterrupted. A search engine allows queries by author, title and publication year. See http://www.idealibrary.com. At present the Library is evaluating a site license offer proposed by the publisher.

  16. Professional WordPress design and development

    CERN Document Server

    Williams, Brad; Stern, Hal

    2014-01-01

    The highest rated WordPress development and design book on the market is back with an all new third edition. Professional WordPress is the only WordPress book targeted to developers, with advanced content that exploits the full functionality of the most popular CMS in the world. Fully updated to align with WordPress 4.1, this edition has updated examples with all new screenshots, and full exploration of additional tasks made possible by the latest tools and features. You will gain insight into real projects that currently use WordPress as an application framework, as well as the basic usage a

  17. Optimizing of SPS pressed SrFe12O19 pellets from nano-powder

    DEFF Research Database (Denmark)

    Mortensen, Anna; Stingaciu, Marian; Christensen, Mogens

    2015-01-01

    direction giving a higher net magnetization. One challenge is to optimize the pressing conditions in order to maximize the remanence and thus the energy product. In present work the SrFe12O19 powder was made in an autoclave and was analysed by X-ray diffraction and Rietveld Refinement to determine particle...... size. The powder was pressed using Spark Plasma Syntering (SPS) system at different conditions in order to investigate how the pressing conditions influence the magnetic properties. It was found, that pressing at 950oC leads to a much better alignment than pellets pressed at room temperature....... Furthermore, ball milling seems to decrease the degree of alignment and thereby the magnetic remanence which leads to a lower energy product. The magnetization was characterized using Vibrating Sample Magnetometer. By applying an external magnetic field before pressing, the alignment is heightened...

  18. Towards a more responsible press

    Directory of Open Access Journals (Sweden)

    Taimur ul Hassan

    2012-12-01

    Full Text Available The article analyses Pakistan’s newspapers’ performance with regard to civil society in2003 by using content analysis approach. There is no gainsaying that a strong civil society guaranteesa strong democracy. In Pakistan, spells of military rule have stunted the growth of democracy,adversely affecting civil society. Media too has suffered as a result. Normative theories of media callfor laying down norms and conventions for media. In democracy, all sections of society should berepresented in media. In Pakistan’s case, due to military regimes and quasi democratic governments,combined with the demands of market economy, the media have largely not been able to fulfill thisresponsibility towards society. Social Responsibility demands that the media must fulfill itsresponsibility towards society, while giving a free space to all voices of society. In Pakistan, whethernewspapers played that role in 2003 when civil society had accelerated its campaign to end honorkillings and crimes against women is investigated. The findings show that newspapers did supportcivil society, showing a gradual movement towards a more responsible press.

  19. Press Advertising – Varieties and Sub-Varieties. Methods of Promoting the Press

    OpenAIRE

    Mikosz, Joanna

    2016-01-01

    In the text entitled “Press advertising – varieties and sub-varieties. Methods of promoting the press”, the author discusses press advertising, which is a fast developing mass-media phenomenon. Modernity has granted press advertising a high quality of print and paper, as well as Infinite possibilities of combining various promotional forms with the press. The author argues that press advertising is one of the best ways in which a company can communicate with the market. Its advantage is, abov...

  20. Smashing WordPress Beyond the Blog

    CERN Document Server

    Hedengren, Thord Daniel

    2011-01-01

    Smashing WordPress shows you how to utilize the power of the WordPress platform, and provides a creative spark to help you build WordPress-powered sites that go beyond the obvious. The second edition of Smashing WordPress has been updated for WordPress 3.1+, which includes internal, custom post types, the admin bar, and lots of other useful new features. You will learn the core concepts used to post types, the admin bar, and lots of other useful new features. You will learn the core concepts used to build just about anything in WordPress, resulting in fast deployments and greater design flexib

  1. Elbow joint fatigue and bench-press training.

    Science.gov (United States)

    Huang, Yen-Po; Chou, You-Li; Chen, Feng-Chun; Wang, Rong-Tyai; Huang, Ming-Jer; Chou, Paul Pei-Hsi

    2014-01-01

    Bench-press exercises are among the most common form of training exercise for the upper extremity because they yield a notable improvement in both muscle strength and muscle endurance. The literature contains various investigations into the effects of different bench-press positions on the degree of muscle activation. However, the effects of fatigue on the muscular performance and kinetics of the elbow joint are not understood fully. To investigate the effects of fatigue on the kinetics and myodynamic performance of the elbow joint in bench-press training. Controlled laboratory study. Motion research laboratory. A total of 18 physically healthy male students (age = 19.6 ± 0.8 years, height = 168.7 ± 5.5 cm, mass = 69.6 ± 8.6 kg) participated in the investigation. All participants were right-hand dominant, and none had a history of upper extremity injuries or disorders. Participants performed bench-press training until fatigued. Maximal possible number of repetitions, cycle time, myodynamic decline rate, elbow-joint force, and elbow-joint moment. We observed a difference in cycle time in the initial (2.1 ± 0.42 seconds) and fatigue (2.58 ± 0.46 seconds) stages of the bench-press exercise (P = .04). As the participants fatigued, we observed an increase in the medial-lateral force (P = .03) and internal-external moment (P ≤ .04) acting on the elbow joint. Moreover, a reduction in the elbow muscle strength was observed in the elbow extension-flexion (P ≤ .003) and forearm supination-pronation (P ≤ .001) conditions. The results suggest that performing bench-press exercises to the point of fatigue increases elbow-joint loading and may further increase the risk of injury. Therefore, when clinicians design bench-press exercise regimens for general athletic training, muscle strengthening, or physical rehabilitation, they should control carefully the maximal number of repetitions.

  2. PRESS FREEDOM IN SINGAPORE AND MALAYSIA: DEFAMATION

    OpenAIRE

    Georgia Kate Chapman

    2015-01-01

    This paper focuses on the arguments around restriction on freedom of the press in the Strong States of Singapore and Malaysia. It assesses the presence of constraints on press freedoms in democratic western countries imposed by corporation rather than state and the similar effects that these constraints may have on bias present in publicly accessible news reporting. It argues that independence of the press does not just require protection from legal and executive regulation, but also protecti...

  3. Microplasticity in hot-pressed beryllium

    International Nuclear Information System (INIS)

    Plane, D.C.; Bonfield, W.

    1977-01-01

    Closed hysteresis loops measured in the microstrain region of hot pressed, commercially pure, polycrystalline beryllium are correlated with a dislocation - impurity atom, energy dissipating mechanism. (author)

  4. WordPress 3.7 complete

    CERN Document Server

    Król, Karol

    2013-01-01

    WordPress 3.5 Complete: Third Edition is a comprehensive and step-by-step tutorial packed with screenshots and examples to make it easy and quick to pick it up.This WordPress book is a guide to WordPress for online publishers and web developers. If you are new to blogging and want to create your own blog or website from scratch, then ""WordPress 3.5 Complete: Third Edition"" is for you. No prior knowledge of HTML/CSS or PHP is required.

  5. Activation of Selected Core Muscles during Pressing

    Directory of Open Access Journals (Sweden)

    Thomas W. Nesser

    2015-10-01

    Full Text Available Introduction: Unstable surface training is often used to activate core musculature during resistance training. Unfortunately, unstable surface training is risky and leads to detraining. Purpose: The purpose of this study was to determine core muscle activation during stable surface ground-based lifts. Methods: Fourteen recreational trained and former NCAA DI athletes (weight 84.2 ± 13.3 kg; height 176.0 ± 9.5 cm; age 20.9 ± 2.0 years volunteered for participation. Subjects completed two ground-based lifts: overhead press and push-press. Surface EMG was recorded from 4 muscles on the right side of the body (Rectus Abdominus (RA, External Oblique (EO, Transverse Abdominus (TA, and Erector Spinae (ES. Results: Paired sample T-tests identified significant muscle activation differences between the overhead press and the push-press included ES and EO. Average and peak EMG for ES was significantly greater in push-press (P<0.01. Anterior displacement of COP was significantly greater in push-press compared to overhead press during the eccentric phase. Conclusion: The push-press was identified as superior in core muscle activation when compared to the overhead pressing exercise. Keywords: torso, stability, weight lifting, resistance training

  6. Justification and manufacturing quality assurance for the use of hot Isostatically pressed, reactor coolant system components in PWR plant

    International Nuclear Information System (INIS)

    Sulley, J. L.; Hookham, I. D.

    2008-01-01

    This paper presents an overview of the work undertaken by Rolls-Royce to introduce Hot Isostatically Pressed (HIP) components into Pressurised Water Reactor plant. It presents the work from a design justification and manufacturing quality assurance perspective, rather than from a pure metallurgical perspective, although some metallurgical and mechanical property comparisons with the traditional forged material are presented. Although the HIP process is not new, it was new in its application to Rolls-Royce designed nuclear reactor plant. In order to satisfy the regulatory requirement of 'Proven Engineering Practices' with regard to the introduction of new material processes, and to provide a robust manufacturing substantiation leg of a multi-legged safety case, Rolls-Royce has implemented an evolving, staged approach, starting with HIP bonding of solid valve seats into small bore valve pressure boundaries. This was followed by powder HIP consolidation of leak-limited, thin-walled toroids, and has culminated in the powder HIP consolidation of components, such as steam generator headers, large bore valves and pipe sections. The paper provides an overview of each of these stages and the approach taken with respect to justification. The paper describes the benefits that Rolls-Royce has realised so far through the introduction of HIPed components, and improvements planned for the future. Structural integrity benefits are described, such as improved grain structure, mechanical properties, and ultrasonic inspection. Project-based benefits are also described, such as provision of an alternative strategic sourcing route, cost and lead-time reduction. A full description is provided of key quality assurance steps applied to the process to ensure a high quality product is delivered commensurate with a high integrity nuclear application. 2008 Rolls-Royce plc. (authors)

  7. Teenagers as Victims in the Press

    Science.gov (United States)

    Andersson, Gunvor; Lundstrom, Tommy

    2007-01-01

    Research into press reporting on young people has tended to concentrate on young people as offenders. In contrast, this article focuses on press coverage of teenagers as victims. Reports in two Swedish newspapers (a morning broadsheet and an evening tabloid) were studied over a period of four months and subjected to a qualitative analysis of…

  8. Communicators take nine Virginia Press Women awards

    OpenAIRE

    Owczarski, Mark

    2008-01-01

    Three Virginia Tech communicators have won Virginia Press Women awards. The winners - Susan Trulove, research division communications manager; Clara Cox, university publications director; and Heather Riley Chadwick, College of Architecture and Urban Studies communication manager - were announced at the Virginia Press Women Annual Spring Conference in Staunton, Va.

  9. 1979: The Campus Student Press in America.

    Science.gov (United States)

    Ingelhart, Louis E.

    1979-01-01

    Discusses a number of topics involving the campus press, including the independence of campus publications, censorship issues, the relationship between the student press and the college administrator, the financing of student newspapers, yearbook production and financing, probable future student publications trends, and the need for appropriate…

  10. Zinc coated sheet steel for press hardening

    Science.gov (United States)

    Ghanbari, Zahra N.

    Galvanized steels are of interest to enhance corrosion resistance of press-hardened steels, but concerns related to liquid metal embrittlement have been raised. The objective of this study was to assess the soak time and temperature conditions relevant to the hot-stamping process during which Zn penetration did or did not occur in galvanized 22MnB5 press-hardening steel. A GleebleRTM 3500 was used to heat treat samples using hold times and temperatures similar to those used in industrial hot-stamping. Deformation at both elevated temperature and room temperature were conducted to assess the coating and substrate behavior related to forming (at high temperature) and service (at room temperature). The extent of alloying between the coating and substrate was assessed on undeformed samples heat treated under similar conditions to the deformed samples. The coating transitioned from an α + Gamma1 composition to an α (bcc Fe-Zn) phase with increased soak time. This transition likely corresponded to a decrease in availability of Zn-rich liquid in the coating during elevated temperature deformation. Penetration of Zn into the substrate sheet in the undeformed condition was not observed for any of the processing conditions examined. The number and depth of cracks in the coating and substrate steel was also measured in the hot-ductility samples. The number of cracks appeared to increase, while the depth of cracks appeared to decrease, with increasing soak time and increasing soak temperature. The crack depth appeared to be minimized in the sample soaked at the highest soak temperature (900 °C) for intermediate and extended soak times (300 s or 600 s). Zn penetration into the substrate steel was observed in the hot-ductility samples soaked at each hold temperature for the shortest soak time (10 s) before being deformed at elevated temperature. Reduction of area and elongation measurements showed that the coated sample soaked at the highest temperature and longest soak time

  11. Process design of press hardening with gradient material property influence

    International Nuclear Information System (INIS)

    Neugebauer, R.; Schieck, F.; Rautenstrauch, A.

    2011-01-01

    Press hardening is currently used in the production of automotive structures that require very high strength and controlled deformation during crash tests. Press hardening can achieve significant reductions of sheet thickness at constant strength and is therefore a promising technology for the production of lightweight and energy-efficient automobiles. The manganese-boron steel 22MnB5 have been implemented in sheet press hardening owing to their excellent hot formability, high hardenability, and good temperability even at low cooling rates. However, press-hardened components have shown poor ductility and cracking at relatively small strains. A possible solution to this problem is a selective increase of steel sheet ductility by press hardening process design in areas where the component is required to deform plastically during crash tests. To this end, process designers require information about microstructure and mechanical properties as a function of the wide spectrum of cooling rates and sequences and austenitizing treatment conditions that can be encountered in production environments. In the present work, a Continuous Cooling Transformation (CCT) diagram with corresponding material properties of sheet steel 22MnB5 was determined for a wide spectrum of cooling rates. Heating and cooling programs were conducted in a quenching dilatometer. Motivated by the importance of residual elasticity in crash test performance, this property was measured using a micro-bending test and the results were integrated into the CCT diagrams to complement the hardness testing results. This information is essential for the process design of press hardening of sheet components with gradient material properties.

  12. Hot pressing of B{sub 4}C/SiC composites

    Energy Technology Data Exchange (ETDEWEB)

    Sahin, F.C.; Turhan, E.; Yesilcubuk, S.A.; Addemir, O. [Ystanbul Technical University, Faculty of Chemistry and Metallurgy, Materials and Metallurgical Engineering Dept., Maslak-Ystanbul (Turkey)

    2005-07-01

    B{sub 4}C/SiC ceramic composites containing 10-20-30 vol % SiC were prepared by hot pressing method. The effect of SiC addition and hot pressing temperature on sintering behaviour and mechanical properties of hot pressed composites were investigated. Microstructures of hot pressed samples were examined by SEM technique. Three different temperatures (2100 deg. C, 2200 deg. C and 2250 deg. C) were used to optimize hot pressing temperature applying 100 MPa pressure under argon atmosphere during the sintering procedure. The highest relative density of 98.44 % was obtained by hot pressing at 2250 deg. C. However, bending strengths of B{sub 4}C/SiC composite samples were lower than monolithic B{sub 4}C in all experimental conditions. (authors)

  13. WordPress web design for dummies

    CERN Document Server

    Sabin-Wilson, Lisa

    2013-01-01

    Updated, full-color guide to creating dynamic websites with WordPress 3.6 In this updated new edition, bestselling For Dummies author and WordPress expert Lisa Sabin-Wilson makes it easy for anyone with a basic knowledge of the WordPress software to create a custom site using complementary technologies such as CSS, HTML, PHP, and MySQL. You'll not only get up to speed on essential tools and technologies and further advance your own design skills, this book also gives you pages of great case studies, so you can see just how other companies and individuals are creating compelling, customized, a

  14. Teach yourself visually complete WordPress

    CERN Document Server

    Majure, Janet

    2013-01-01

    Take your WordPress skills to the next level with these tips, tricks, and tasks Congratulations on getting your blog up and running with WordPress! Now are you ready to take it to the next level? Teach Yourself VISUALLY Complete WordPress takes you beyond the blogging basics with expanded tips, tricks, and techniques with clear, step-by-step instructions accompanied by screen shots. This visual book shows you how to incorporate forums, use RSS, obtain and review analytics, work with tools like Google AdSense, and much more.Shows you how to use mobile tools to edit a

  15. WordPress 24-Hour Trainer

    CERN Document Server

    Plumley, George

    2011-01-01

    The eagerly anticipated second edition, completely updated for WordPress 3.1 As an open source content management system, WordPress allows users to easily build feature-rich web sites with no programming experience. This unique book-and-video package is a friendly, self-paced beginners guide to the latest release of WordPress. Lessons are focused on practical, everyday tasks that users will need to create and maintain their sites: entering new content, creating new pages, managing menus, making content search-engine friendly. Plus you'll find lots of tips based on years of experience teaching

  16. WordPress web application development

    CERN Document Server

    Ratnayake, Rakhitha Nimesh

    2013-01-01

    An extensive, practical guide that explains how to adapt WordPress features, both conventional and trending, for web applications.This book is intended for WordPress developers and designers who have the desire to go beyond conventional website development to develop quality web applications within a limited time frame and for maximum profit. Experienced web developers who are looking for a framework for rapid application development will also find this to be a useful resource. Prior knowledge with of WordPress is preferable as the main focus will be on explaining methods for adapting WordPres

  17. Professional WordPress Plugin Development

    CERN Document Server

    Williams, Brad; Tadlock, Justin

    2011-01-01

    Taking WordPress to the next level with advanced plugin developmentWordPress is used to create self-hosted blogs and sites, and it's fast becoming the most popular content management system (CMS) on the Web. Now you can extend it for personal, corporate and enterprise use with advanced plugins and this professional development guide. Learn how to create plugins using the WordPress plugin API: utilize hooks, store custom settings, craft translation files, secure your plugins, set custom user roles, integrate widgets, work with JavaScript and AJAX, create custom post types. You'll find a practic

  18. Influence of the "Slingshot" bench press training aid on bench press kinematics and neuromuscular activity in competitive powerlifters.

    Science.gov (United States)

    Dugdale, James H; Hunter, Angus; Di Virgilio, Thomas; Macgregor, Lewis J; Hamilton, D Lee

    2017-02-13

    This study examined the acute effects of the 'Slingshot' on bench-press performance, prime-mover surface electromyographic (sEMG) amplitude, and barbell velocity during maximal and submaximal bench-pressing in competitive male powerlifters. Fifteen male powerlifters (mean ± SD age: 27.05 ± 5.94 years; mass: 94.15kg; 1RM bench-press: 139.7 ± 16.79kg) participated in the study. Bench-press strength, average barbell velocity, and sEMG amplitude of the prime mover muscles (triceps brachii, pectoralis major and anterior deltoid) were measured during two conditions; 'Raw' (without use of any assistance) and 'Slingshot' [using the 'Slingshot' to perform both the weight achieved during 'Raw' 1RM testing (Raw max/SS), and absolute 1RM using the 'Slingshot' (SS)]. The results showed that the 'Slingshot' significantly increased bench press 1RM performance by a mean ± SD of 20.67kg ± 3.4kg. Barbell velocity and stick point analysis indicate that this improvement is likely driven by an increase in peak and pre-stick barbell velocity as triceps RMS was lower throughout all rep max phases with the 'Slingshot'. The 'Slingshot' also caused reductions in RMS, specifically of the triceps at all rep ranges but barbell velocity was better maintained in the last reps of all sets. These data indicate that the 'Slingshot' specifically de-loaded the triceps muscle throughout all rep ranges and provide assistance to maintaining barbell velocity under fatigue during later repetitions of multiple-repetition sets. The 'Slingshot' training aid could therefore be used in de-load phases of bench press training or as an over-reaching and velocity training aid.

  19. The effect of pre-treatment parameters on the quality of glass-ceramic wasteforms for plutonium immobilisation, consolidated by hot isostatic pressing

    Energy Technology Data Exchange (ETDEWEB)

    Thornber, Stephanie M.; Heath, Paul G. [Immobilisation Science Laboratory, Department of Materials Science & Engineering, The University of Sheffield, Sir Robert Hadfield Building, Mappin Street, Sheffield S1 3JD (United Kingdom); Da Costa, Gabriel P. [Immobilisation Science Laboratory, Department of Materials Science & Engineering, The University of Sheffield, Sir Robert Hadfield Building, Mappin Street, Sheffield S1 3JD (United Kingdom); Department of Chemical Engineering & Petroleum Engineering, Universidade Federal Fluminense, Rua Passo da Patria 156, CEP 24210-240, Niteroi, RJ (Brazil); Stennett, Martin C. [Immobilisation Science Laboratory, Department of Materials Science & Engineering, The University of Sheffield, Sir Robert Hadfield Building, Mappin Street, Sheffield S1 3JD (United Kingdom); Hyatt, Neil C., E-mail: n.c.hyatt@sheffield.ac.uk [Immobilisation Science Laboratory, Department of Materials Science & Engineering, The University of Sheffield, Sir Robert Hadfield Building, Mappin Street, Sheffield S1 3JD (United Kingdom)

    2017-03-15

    Glass-ceramics with high glass fractions (70 wt%) were fabricated in stainless steel canisters by hot isostatic pressing (HIP), at laboratory scale. High (600 °C) and low (300 °C) temperature pre-treatments were investigated to reduce the canister evacuation time and to understand the effect on the phase assemblage and microstructure of the hot isostatically pressed product. Characterisation of the HIPed materials was performed using scanning electron microscopy (SEM), coupled with energy dispersive X-ray analysis (EDX) and powder X-ray diffraction (XRD). This analysis showed the microstructure and phase assemblage was independent of the variation in pre-treatment parameters. It was demonstrated that a high temperature pre-treatment of batch reagents, prior to the HIP cycle, is beneficial when using oxide precursors, in order to remove volatiles and achieve high quality dense materials. Sample throughput can be increased significantly by utilising a high temperature ex-situ calcination prior to the HIP cycle. Investigation of glass-ceramic wasteform processing utilising a glass frit precursor, produced a phase assemblage and microstructure comparable to that obtained using oxide precursors. The use of a glass frit precursor should allow optimised throughput of waste packages in a production facility, avoiding the need for a calcination pre-treatment required to remove volatiles from oxide precursors. - Highlights: • Optimisation of pre-treatment parameters for HIP glass-ceramics was investigated. • Entrained porosity was minimised by ex-situ bake-out of oxide precursors at 600 °C. • Phase assemblage and microstructure proved independent of bake-out parameters. • Use of glass-frit precursor further improved process s throughput and simplification.

  20. The effect of pre-treatment parameters on the quality of glass-ceramic wasteforms for plutonium immobilisation, consolidated by hot isostatic pressing

    International Nuclear Information System (INIS)

    Thornber, Stephanie M.; Heath, Paul G.; Da Costa, Gabriel P.; Stennett, Martin C.; Hyatt, Neil C.

    2017-01-01

    Glass-ceramics with high glass fractions (70 wt%) were fabricated in stainless steel canisters by hot isostatic pressing (HIP), at laboratory scale. High (600 °C) and low (300 °C) temperature pre-treatments were investigated to reduce the canister evacuation time and to understand the effect on the phase assemblage and microstructure of the hot isostatically pressed product. Characterisation of the HIPed materials was performed using scanning electron microscopy (SEM), coupled with energy dispersive X-ray analysis (EDX) and powder X-ray diffraction (XRD). This analysis showed the microstructure and phase assemblage was independent of the variation in pre-treatment parameters. It was demonstrated that a high temperature pre-treatment of batch reagents, prior to the HIP cycle, is beneficial when using oxide precursors, in order to remove volatiles and achieve high quality dense materials. Sample throughput can be increased significantly by utilising a high temperature ex-situ calcination prior to the HIP cycle. Investigation of glass-ceramic wasteform processing utilising a glass frit precursor, produced a phase assemblage and microstructure comparable to that obtained using oxide precursors. The use of a glass frit precursor should allow optimised throughput of waste packages in a production facility, avoiding the need for a calcination pre-treatment required to remove volatiles from oxide precursors. - Highlights: • Optimisation of pre-treatment parameters for HIP glass-ceramics was investigated. • Entrained porosity was minimised by ex-situ bake-out of oxide precursors at 600 °C. • Phase assemblage and microstructure proved independent of bake-out parameters. • Use of glass-frit precursor further improved process s throughput and simplification.

  1. Effects of Oxygen Content on Tensile and Fatigue Performance of Ti-6Al-4 V Manufactured by Selective Laser Melting

    Science.gov (United States)

    Quintana, Oscar A.; Tong, Weidong

    2017-12-01

    We investigated the selective laser melting (SLM) process for development of Ti-6Al-4 V solid material with oxygen content corresponding to the extra low interstitial (ELI) and non-ELI conditions. The microstructure, chemistry, and tensile properties of samples in as-built and hot isostatically pressed (HIPed) condition were evaluated for both material types, while fatigue performance was evaluated by rotating bending fatigue tests on both smooth and notched SLM ELI and non-ELI Ti-6Al-4 V samples in HIPed condition.

  2. Study of Servo Press with a Flywheel

    Science.gov (United States)

    Tso, Pei-Lum; Li, Cheng-Ho

    The servo press with a flywheel is able to provide flexible motions with energy-saving merit, but its true potential has not been thoroughly studied and verified. In this paper, such the “hybrid-driven” servo press is focused on, and the stamping capacity and the energy distribution between the flywheel and the servomotor are investigated. The capacity is derived based on the principle of energy conservation, and a method of using a capacity percentage plane for evaluation is proposed. A case study is included to illustrate and interpret that the stamping capacity is highly dependent on the programmed punch motions, thus the capacity prediction is always necessary while applying this kind of servo press. The energy distribution is validated by blanking experiments, and the results indicate that the servomotor needs only to provide 15% to the flywheel torque, 12% of the total stamping energy. This validates that the servomotor power is significantly saved in comparison with conventional servo presses.

  3. A virtual model of the bench press exercise.

    Science.gov (United States)

    Rahmani, Abderrahmane; Rambaud, Olivier; Bourdin, Muriel; Mariot, Jean-Pierre

    2009-08-07

    The objective of this study was to design and validate a three degrees of freedom model in the sagittal plane for the bench press exercise. The mechanical model was based on rigid segments connected by revolute and prismatic pairs, which enabled a kinematic approach and global force estimation. The method requires only three simple measurements: (i) horizontal position of the hand (x(0)); (ii) vertical displacement of the barbell (Z) and (iii) elbow angle (theta). Eight adult male throwers performed maximal concentric bench press exercises against different masses. The kinematic results showed that the vertical displacement of each segment and the global centre of mass followed the vertical displacement of the lifted mass. Consequently, the vertical velocity and acceleration of the combined centre of mass and the lifted mass were identical. Finally, for each lifted mass, there were no practical differences between forces calculated from the bench press model and those simultaneously measured with a force platform. The error was lower than 2.5%. The validity of the mechanical method was also highlighted by a standard error of the estimate (SEE) ranging from 2.0 to 6.6N in absolute terms, a coefficient of variation (CV) or =0.99 for all the lifts (pbench press exercises in both field and laboratory conditions.

  4. WordPress 3 For Business Bloggers

    CERN Document Server

    Thewlis, Paul

    2011-01-01

    This is a practical, hands-on book based around a fictitious case study blog, which you will build on a development server using WordPress. The case study grows chapter by chapter, from installing your local development server, right up to the finished blog. This book is for anybody running or starting a business blog using WordPress, whether you plan to use your blog for PR and marketing, or want to profit directly from blogging.

  5. Denmark, Democracy and the Free Press

    DEFF Research Database (Denmark)

    Breiting, Søren

    2006-01-01

    What's important to Danish people in Denmark and in the world - most will argue for the importance of a free critical press, solidarity with people who need help and a peaceful world.......What's important to Danish people in Denmark and in the world - most will argue for the importance of a free critical press, solidarity with people who need help and a peaceful world....

  6. The Liberal Struggle for Press Freedom

    DEFF Research Database (Denmark)

    Mogensen, Kirsten

    In this paper, the public debate following the re-ligion-motivated assassination of Dutch filmmaker Theo van Gogh in November 2004 is examined. The paper aims at describ-ing religious as well as secular positions in the Danish debate about freedom of speech and press in relation to religious issues....... Historically, the concept of press freedom was linked to a fight for religious freedom in London, as described by Siebert....

  7. Chip compacting press; Jido kirikuzu asshukuki

    Energy Technology Data Exchange (ETDEWEB)

    Oura, K. [Yuken Kogyo Co. Ltd., Kanagawa (Japan)

    1998-08-15

    The chips exhausted from various machine tools are massy, occupy much space and make working environment worse by staying added cutting oil to lower part. The chips are exhausted as a result of machining and have not constant quality. Even if used material is same the chips have various shapes and properties by kinds and machining methods of used machine tools, and are troublesome materials from a standpoint of their treatment. Pressing and solidification of the chips have frequently been tried. A chip compacting press introduced in this paper, a relatively cheap chip compacting press aimed for relatively small scale chip treatment, and has such characteristics and effects as follows. Chips are pressed and solidified by each raw material, so fractional management can be easily conducted. As casting metal chips and curled chips of iron and aluminum can be pressed to about 1/3 to 1/5 and about 1/40, respectively, space saving can be conducted. Chip compacting pressing upgrades its transporting efficiency to make possible to reduce its transporting cost. As chip solidification controls its oxidation and most cutting oil are removed, chips are easy to recycle. 2 figs., 1 tab.

  8. Production of press moulds by plasma spray forming process

    International Nuclear Information System (INIS)

    Borisov, Y.; Myakota, I.; Polyakov, S.

    2001-01-01

    Plasma spray forming process for production of press moulds which are used for manufacture of articles from plastics was developed. The press moulds were produced by plasma spraying of Cu-Al-Fe-alloy powder on surface of a master model. The master models were made from non-metallic materials with heat resistance below 70 C (wood, gypsum etc). Double cooling system which provides for a control of surface model temperature and quenching conditions of sprayed material was designed. It made possible on the one hand to support model surface temperature below 70 C and on the other hand to provide for temperature conditions of martensite transformation in Cu-Al-system with a fixation of metastable ductile α + β 1 -phase. This allowed to decrease residual stresses in sprayed layer (up to 0,5-2,5 MPa), to increase microhardness of the coating material (up to 1200-1800 MPa) and its ductility (σ B = 70-105 MPa, δ = 6-12 %). This plasma spray forming process makes possible to spray thick layers (5-20 mm and more) without their cracking and deformation. The process is used for a production of press moulds which are applied in shoes industry, for fabrication of toys, souvenirs etc. (author)

  9. Reducing VOC Press Emission from OSB Manufacturing; FINAL

    International Nuclear Information System (INIS)

    Gary D, McGinnis; Laura S, WIlliams; Amy E, Monte; Jagdish Rughani; Brett A, Niemi; Thomas M, Flicker

    2001-01-01

    Current regulations require industry to meet air emission standards with regard to particulates, volatile organic compounds (VOCs), hazardous air pollutants (HAPs) and other gases. One of many industries that will be affected by the new regulations is the wood composites industry. This industry generates VOCs, HAPs, and particulates mainly during the drying and pressing of wood. Current air treatment technologies for the industry are expensive to install and operate. As regulations become more stringent, treatment technologies will need to become more efficient and cost effective. The overall objective of this study is to evaluate the use of process conditions and chemical additives to reduce VOC/HAPs in air emitted from presses and dryers during the production of oriented strand board

  10. PRESS FREEDOM IN SINGAPORE AND MALAYSIA: DEFAMATION

    Directory of Open Access Journals (Sweden)

    Georgia Kate Chapman

    2015-04-01

    Full Text Available This paper focuses on the arguments around restriction on freedom of the press in the Strong States of Singapore and Malaysia. It assesses the presence of constraints on press freedoms in democratic western countries imposed by corporation rather than state and the similar effects that these constraints may have on bias present in publicly accessible news reporting. It argues that independence of the press does not just require protection from legal and executive regulation, but also protection from large media corporations and their political alignments. This report will assess the bias of reporting and news media publication that exists in Malaysia and Singapore due to legislative and regulatory constraints as opposed to bias that exist in the western liberal democratic nations of the United Kingdom (UK and the United States of America (USA due to Media Organisation control.

  11. CSR-communication in the Business Press

    DEFF Research Database (Denmark)

    Morsing, Mette; Langer, Roy

    on a broadly encompassing and ambiguous definition of CSR. Our empirical data shows how the business press in its discourse on CSR provides no clarity on the definition of CSR in terms of a coherent motive, a dominant stakeholder or a consistent issue, but rather maintains ambiguity and imprecision about......In this paper we analyze the construction of corporate social responsibility in the business press as an act of strategic ambiguity. While corporate social responsibility (CSR) generally evokes positive associations in public opinion, this paper demonstrates that these associations are based...... is systematically maintained in the business press. We refer to this process as strategic ambiguity. The paper discusses the potential value and limitations of framing CSR in a state of strategic ambiguity in the context of the concurrent rethinking of the role of business in modern welfare societies....

  12. Internet Marketing with WordPress

    CERN Document Server

    Mercer, David

    2011-01-01

    The book's accompanying Interactive learning environment on siteprebuilder.com gives you an online place to enhance and extend your practical experience through exercises, consolidate your learning and theoretical knowledge with marked quizzes, interaction with your WordPress marketing community, and fun and exciting extras such as challenges and competitions. This book is for people already using WordPress, who want more visitors, better visitors, and to convert more of them into paying customers. No prior marketing experience is required, although a basic understanding of either hosted or se

  13. WordPress 24-hour trainer

    CERN Document Server

    Plumley, George

    2015-01-01

    Create and expand feature-rich sites with no programming experience Ready to build, maintain, and expand your web site with WordPress but have no prior programming experience? WordPress 24-Hour Trainer, 3rd Edition is your book-and-video learning solution that walks you step-by-step through all the important features you will need to know. Lessons range from focused, practical everyday tasks to more advanced, creative features. Learn from an industry professional how to enter content, create pages, manage menus, utilize plug-ins, connect to social media, create membership and e-commerce site

  14. Strength-ductility relationships in intermediate purity hot-pressed beryllium

    International Nuclear Information System (INIS)

    Stonehouse, A.J.; Bielawski, C.A.; Paine, R.M.

    1977-01-01

    The strength of vacuum hot-pressed, intermediate purity beryllium may be substantially increased without sacrifice of the strain capacity of the present grade (S-65) through decrease in the average grain size. Tensile strength of 517 MPa, 0.2% offset yield strength of 414 MPa with minimum 3% tensile elongation in all test directions could be commercially achieved. The tangent modulus of such material is quite attractive and suffers only about 10% degradation from room temperature to 260 0 C. The tangent modulus is dramatically enhanced by the presence of a yield point. The ductility of the materials studied did not appear to be affected by the BeO content across the range of 0.5 to 2.0% using nominal -44 to -15 μm powder particle sizes. All fine-grained pressings exhibited yield points in the as-pressed condition. Either full-density or sub-density hot-pressed billets given a hot isostatic pressing treatment without the use of cans showed only slight yield points after the HIP treatment with essentially the same strength and ductility factors as in the pressed condition. A plot of grain size vs yield strength in the as-pressed condition projects to an intercept with the fracture strength line at about 3 μm grain size. A similar plot after the HIP treatment shows a yield strength line parallel to the fracture strength line with no projected intercept predicting a completely brittle material. (author)

  15. AUPress: A Comparison of an Open Access University Press with Traditional Presses

    Science.gov (United States)

    McGreal, Rory; Chen, Nian-Shing

    2011-01-01

    This study is a comparison of AUPress with three other traditional (non-open access) Canadian university presses. The analysis is based on the rankings that are correlated with book sales on Amazon.com and Amazon.ca. Statistical methods include the sampling of the sales ranking of randomly selected books from each press. The results of one-way…

  16. Bullying the media : Cultural and climato-economic readings of press repression versus press freedom

    NARCIS (Netherlands)

    Van de Vliert, E.

    Journalists and media assistants in many places are murdered, imprisoned, censored, threatened, and similarly harrassed. Here I document that, and explain why, there are three climato-economic niches of press repression versus press freedom as part of broader syndromes of national culture. A

  17. Change of Pressing Chamber Conicalness at Briquetting Process in Briquetting Machine Pressing Chamber

    Directory of Open Access Journals (Sweden)

    Peter Križan

    2012-01-01

    Full Text Available In this paper, we will present the impact of the conical shape of a pressing chamber, an important structural parameter. Besides the known impact of the technological parameters of pressing chambers, it is also very important to pay attention to their structural parameters. In the introduction, we present a theoretical analysis of pressing chamber conicalness. An experiment aimed at detecting this impact was performed at our institute, and it showed that increasing the conicalness of a pressing chamber improves the quality of the final briquettes. The conicalness of the pressing chamber has a significanteffect on the final briquette quality and on the construction of briquetting machines. The experimental findings presented here show the importance of this parameter in the briquetting process.

  18. 28 CFR 540.64 - Press pools.

    Science.gov (United States)

    2010-07-01

    ... Judicial Administration BUREAU OF PRISONS, DEPARTMENT OF JUSTICE INSTITUTIONAL MANAGEMENT CONTACT WITH PERSONS IN THE COMMUNITY Contact With News Media § 540.64 Press pools. (a) The Warden may establish a... shall notify all news media representatives who have requested interviews or visits that have not been...

  19. Law of the Student Press. Second Edition.

    Science.gov (United States)

    Student Press Law Center, Washington, DC.

    Noting dramatic changes in First Amendment protections for high school students and new legal issues facing college newspaper editors, this book describes in detail the legal rights and responsibilities of both the high school and college press. While the book is extensively footnoted, it intentionally avoids "legal-ese" and "brings…

  20. Press kit kicks off new branding.

    Science.gov (United States)

    Rees, Tom

    2004-01-01

    A smartly produced press kit resulted in unprecedented news coverage when Denver's Porter Adventist Hospital recently unveiled plans for an extensive 80 million dollars redevelopment. A news conference was held to announce this plan, along with the opening of the hospital's new emergency department. The overall effort is part of the new branding strategy of the 75-year-old hospital.

  1. The Moral Universes of Libertarian Press Theory.

    Science.gov (United States)

    Wuliger, Gregory T.

    1991-01-01

    Uses Kantian logic to analyze the statement of Libertarian press theory "Truth beats falsehood in a free marketplace of ideas" as a definition, an observation, and a universal truth. Notes three corresponding moral universes, with differing ethical obligations. Discusses strengths and weaknesses of each. Cautions media ethics analysts…

  2. Investigation of pressing of molybdenum powder compacts

    International Nuclear Information System (INIS)

    Mymrin, S.A.; Kuznetsov, V.Eh.; Yampol'skij, M.L.; Leonov, S.A.; Mikhridinov, R.M.; Korzukhin, V.A.

    1990-01-01

    Results of an experimental investigation into pressing of compacts of MCh type molybdenum powders using the industrial equipment are presented. To measure the density of powder molybdenum billets a radioisotopic density meter with cesium-137 is used as radioactive gamma radiation source. The dependence of the produced billet density on the specific compacting pressure at different values of the powder bulk density is ascertained

  3. Eye-Pressing by Visually Impaired Children.

    Science.gov (United States)

    Jan, James E.; And Others

    1983-01-01

    The nature of eye-pressing as a visual stimulation mannerism in children with severely impaired eyesight is examined, and a possible physiological explanation (that self-stimulation occurs when the demand of the brain for meaningful visual information is not met) is offered. (CL)

  4. Spontaneous pneumomediastinum after bench press training.

    Science.gov (United States)

    Nishino, Tomoya

    2017-04-01

    Spontaneous pneumomediastinum is often associated with asthma and mainly affects adolescent males with a tall, thin body habitus. A 17-year-old man complained of chest and pharyngeal pain after bench press training and spontaneous pneumomediastinum was diagnosed. It should be considered in the differential diagnosis of chest pain of uncertain cause.

  5. A Journalist's Guide to the Free Press.

    Science.gov (United States)

    Ingelhart, Louis

    1996-01-01

    Summarizes the content of the federal constitution and various state constitutions regarding freedom of the press. Examines certain borderline issues, including actions and expressions, pornography, defamation, libel, and copyrighted material. States that regulation of unprotected material must be reasonable, specific, and clear. Discusses what…

  6. Free Press in a Constitutional Democracy

    Science.gov (United States)

    Lucianek, Christine

    2014-01-01

    This article describes a lesson in which students will examine several views expressed by the founders to understand the context for including freedom of the press in the First Amendment. Students will be asked to think about the role that the news media and the need to be an informed citizen continue to play in our democracy. Students will…

  7. [Report from the Student Press Law Center.

    Science.gov (United States)

    Student Press Law Center, Washington, DC.

    The Student Press Law Center serves as a national clearinghouse to collect, analyze, and distribute information on the First Amendment rights of student journalists and journalism teachers and on violations of these rights in high schools and colleges. This report details information concerning current censorship incidents: the investigation by…

  8. When International Press Rights "Are" the News

    Science.gov (United States)

    Freedman, Eric

    2006-01-01

    In many countries, reporters and editors face criminal prosecution, censorship, self-censorship, exile, tax audits, loss of broadcast and publication licenses, loss of jobs, assault, and even assassination based on how they practice their profession. Press rights and human rights advocacy groups try to draw media and official attention to those…

  9. Trial access to Cambridge University Press ebooks

    CERN Multimedia

    CERN Library

    2011-01-01

    From 1 August till 31 October, CERN users are invited to enjoy a trial access to all Cambridge University Press electronic books: http://ebooks.cambridge.org/. Please don't hesitate to send feedback to library.desk@cern.ch.

  10. Dynamic balance abilities of collegiate men for the bench press.

    Science.gov (United States)

    Piper, Timothy J; Radlo, Steven J; Smith, Thomas J; Woodward, Ryan W

    2012-12-01

    This study investigated the dynamic balance detection ability of college men for the bench press exercise. Thirty-five college men (mean ± SD: age = 22.4 ± 2.76 years, bench press experience = 8.3 ± 2.79 years, and estimated 1RM = 120.1 ± 21.8 kg) completed 1 repetition of the bench press repetitions for each of 3 bar loading arrangements. In a randomized fashion, subjects performed the bench press with a 20-kg barbell loaded with one of the following: a balanced load, one 20-kg plate on each side; an imbalanced asymmetrical load, one 20-kg plate on one side and a 20-kg plate plus a 1.25-kg plate on the other side; or an imbalanced asymmetrical center of mass, 20-kg plate on one side and sixteen 1.25-kg plates on the other side. Subjects were blindfolded and wore ear protection throughout all testing to decrease the ability to otherwise detect loads. Binomial data analysis indicated that subjects correctly detected the imbalance of the imbalanced asymmetrical center of mass condition (p[correct detection] = 0.89, p < 0.01) but did not correctly detect the balanced condition (p[correct detection] = 0.46, p = 0.74) or the imbalanced asymmetrical condition (p[correct detection] = 0.60, p = 0.31). Although it appears that a substantial shift in the center of mass of plates leads to the detection of barbell imbalance, minor changes of the addition of 1.25 kg (2.5 lb) to the asymmetrical condition did not result in consistent detection. Our data indicate that the establishment of a biofeedback loop capable of determining balance detection was only realized under a high degree of imbalance. Although balance detection was not present in either the even or the slightly uneven loading condition, the inclusion of balance training for upper body may be futile if exercises are unable to establish such a feedback loop and thus eliciting an improvement of balance performance.

  11. The positive effect of hot isostatic pressing on improving the anisotropies of bending and impact properties in selective laser melted Ti-6Al-4V alloy

    International Nuclear Information System (INIS)

    Wu, Ming-Wei; Lai, Pang-Hsin

    2016-01-01

    Selective laser melting (SLM) is a versatile additive manufacturing process for fabricating solid or porous metallic materials with complicated three-dimensional shapes. SLM Ti alloys, particularly Ti-6Al-4V, and other alloys have been manufactured and analyzed in numerous studies. However, the high anisotropy of the microstructures and inconsistent mechanical properties of SLM materials have been extensively reported, and these disadvantages could prohibit its widespread use. To clarify how to alleviate the anisotropic behaviors of SLM materials, the main objective of this study was to evaluate the influences of hot isostatic pressing (HIP) on the microstructure, densification, bending strength, impact toughness, and fracture behavior of the as-built Ti-6Al-4V alloy. The results showed that the vertical and horizontal building directions obviously affect the bending and impact properties of as-built alloys. The transverse rupture strength (TRS) and impact energy of the horizontally-built alloy were respectively found to be 48% and 100% higher than those of the vertically-built one. In the vertically-built alloy, disc-shaped building defects, identified by X-ray computed tomography (CT) and microscopy, obviously reduce the effective load-bearing cross-section and deteriorate the bending and impact performances. After HIP at 1000 °C/150 MPa, the α′-martensite structure in the as-built alloy is transformed into an α+β lamellar one, and the disc-shaped building defects are evidently eliminated. As a result, the impact energies of as-built vertical and horizontal specimens are improved by 28 J (560%) and 19 J (190%), respectively, and the TRS of the as-built vertical alloy is raised by 550 MPa (37%). Consequently, the discrepancies in TRS and impact energy between the HIPed vertical and horizontal specimens are merely 3% and 14%, respectively, and the anisotropic behaviors of the SLM Ti-6Al-4V alloy are thus substantially lessened.

  12. The positive effect of hot isostatic pressing on improving the anisotropies of bending and impact properties in selective laser melted Ti-6Al-4V alloy

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Ming-Wei, E-mail: mwwu@ntut.edu.tw; Lai, Pang-Hsin

    2016-03-21

    Selective laser melting (SLM) is a versatile additive manufacturing process for fabricating solid or porous metallic materials with complicated three-dimensional shapes. SLM Ti alloys, particularly Ti-6Al-4V, and other alloys have been manufactured and analyzed in numerous studies. However, the high anisotropy of the microstructures and inconsistent mechanical properties of SLM materials have been extensively reported, and these disadvantages could prohibit its widespread use. To clarify how to alleviate the anisotropic behaviors of SLM materials, the main objective of this study was to evaluate the influences of hot isostatic pressing (HIP) on the microstructure, densification, bending strength, impact toughness, and fracture behavior of the as-built Ti-6Al-4V alloy. The results showed that the vertical and horizontal building directions obviously affect the bending and impact properties of as-built alloys. The transverse rupture strength (TRS) and impact energy of the horizontally-built alloy were respectively found to be 48% and 100% higher than those of the vertically-built one. In the vertically-built alloy, disc-shaped building defects, identified by X-ray computed tomography (CT) and microscopy, obviously reduce the effective load-bearing cross-section and deteriorate the bending and impact performances. After HIP at 1000 °C/150 MPa, the α′-martensite structure in the as-built alloy is transformed into an α+β lamellar one, and the disc-shaped building defects are evidently eliminated. As a result, the impact energies of as-built vertical and horizontal specimens are improved by 28 J (560%) and 19 J (190%), respectively, and the TRS of the as-built vertical alloy is raised by 550 MPa (37%). Consequently, the discrepancies in TRS and impact energy between the HIPed vertical and horizontal specimens are merely 3% and 14%, respectively, and the anisotropic behaviors of the SLM Ti-6Al-4V alloy are thus substantially lessened.

  13. Graphic Arts: Book Three. The Press and Related Processes.

    Science.gov (United States)

    Farajollahi, Karim; And Others

    The third of a three-volume set of instructional materials for a graphic arts course, this manual consists of nine instructional units dealing with presses and related processes. Covered in the units are basic press fundamentals, offset press systems, offset press operating procedures, offset inks and dampening chemistry, preventive maintenance…

  14. Bench press exercise: the key points.

    Science.gov (United States)

    Padulo, J; Laffaye, G; Chaouachi, A; Chamari, K

    2015-06-01

    The bench press exercise (BPE) is receiving increasing interest as a field testing, training/therapeutic modality to improve neuromuscular performance or to increase bone mass density. Several studies have been performed using BPE as a standard for increasing upper-limb strength. For this purpose, the position of the bar, the loads, the sets, the number of repetitions, the recovery time in-between sets, the movement speed, the muscular work and the use of the determination of the one repetition maximum (1-RM) are the classical tools investigated in the literature that have been shown to affect the BPE effect on neuromuscular. The goal of the present short review is to make a picture of the current knowledge on the bench press exercise, which could be very helpful for a better understanding of this standard movement and its effects. Based on the related literature, several recommendations on these key points are presented here.

  15. Method for hot pressing beryllium oxide articles

    Science.gov (United States)

    Ballard, Ambrose H.; Godfrey, Jr., Thomas G.; Mowery, Erb H.

    1988-01-01

    The hot pressing of beryllium oxide powder into high density compacts with little or no density gradients is achieved by employing a homogeneous blend of beryllium oxide powder with a lithium oxide sintering agent. The lithium oxide sintering agent is uniformly dispersed throughout the beryllium oxide powder by mixing lithium hydroxide in an aqueous solution with beryllium oxide powder. The lithium hydroxide is converted in situ to lithium carbonate by contacting or flooding the beryllium oxide-lithium hydroxide blend with a stream of carbon dioxide. The lithium carbonate is converted to lithium oxide while remaining fixed to the beryllium oxide particles during the hot pressing step to assure uniform density throughout the compact.

  16. Freedom of the Press – two concepts

    Directory of Open Access Journals (Sweden)

    Markus Meckl

    2015-03-01

    Full Text Available In 1644 the debate for freedom of expression started in modern times thanks to John Milton’s Areopagitica, where he still argued about God in order to justify his quest for freedom. With the enlightenment God lost his unifying role for society and could no longer serve as justification. Two arguments were brought then forward to justify freedom of the press: One by the continental movement of the enlightenment; the other from within the movement of utilitarianism, and most influentially by John Stuart Mill. Both underlined the importance of truth; however, they differed in their understanding on what truth was good for. This difference in their arguments had a lasting impact on the debate on the limits of freedom of the press.

  17. Microstructural evolution and mechanical properties of powder metallurgy Ti–6Al–4V alloy based on heat response

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Ruipeng [School of Materials and Metallurgy, Northeastern University, Shenyang 110819 (China); Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Xu, Lei, E-mail: lxu@imr.ac.cn [Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Wu, Jie; Yang, Rui [Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Zong, Bernie Y. [Key Laboratory for Anisotropy and Texture of Materials, Ministry of Education, Northeastern University, Shenyang 110819 (China)

    2015-07-15

    In present work, powder metallurgy (PM) Ti–6Al–4V alloy was produced by hot isostatic pressing (HIPing) from gas atomized powder. Various HIPing conditions and heat treatments were used to investigate the heat response of PM Ti–6Al–4V alloy. The results show that the optimization of HIPing parameters is temperature from 920 to 940 °C, pressure over 120 MPa and holding for 3 h. The microstructure of powder compact changes significantly after different heat treatments, while there was no obvious difference in tensile properties. Temperature induced porosity (TIP) in powder compact occurred after annealing at 930 °C for 1 h plus aging. The TIP has no obvious effects on tensile, impact, and fracture toughness properties of powder compact, but the TIP has an adverse effect on fatigue property, especially at shorter fatigue lives. In order to eliminate the TIP in powder compact, several probable solutions were suggested for the application of titanium powder components.

  18. Microstructural evolution and mechanical properties of powder metallurgy Ti–6Al–4V alloy based on heat response

    International Nuclear Information System (INIS)

    Guo, Ruipeng; Xu, Lei; Wu, Jie; Yang, Rui; Zong, Bernie Y.

    2015-01-01

    In present work, powder metallurgy (PM) Ti–6Al–4V alloy was produced by hot isostatic pressing (HIPing) from gas atomized powder. Various HIPing conditions and heat treatments were used to investigate the heat response of PM Ti–6Al–4V alloy. The results show that the optimization of HIPing parameters is temperature from 920 to 940 °C, pressure over 120 MPa and holding for 3 h. The microstructure of powder compact changes significantly after different heat treatments, while there was no obvious difference in tensile properties. Temperature induced porosity (TIP) in powder compact occurred after annealing at 930 °C for 1 h plus aging. The TIP has no obvious effects on tensile, impact, and fracture toughness properties of powder compact, but the TIP has an adverse effect on fatigue property, especially at shorter fatigue lives. In order to eliminate the TIP in powder compact, several probable solutions were suggested for the application of titanium powder components

  19. Effects of consolidation temperature, strength and microstructure on fracture toughness of nanostructured ferritic alloys

    International Nuclear Information System (INIS)

    Miao, P.; Odette, G.R.; Yamamoto, T.; Alinger, M.; Hoelzer, D.; Gragg, D.

    2007-01-01

    Fully consolidated nanostructured ferritic alloys (NFAs) were prepared by attritor milling pre-alloyed Fe-14Cr-3W-0.4Ti and 0.3 wt% Y 2 O 3 powders, followed by hot isostatic pressing (HIPing) at 1000 o C or 1150 o C at 200 MPa for 4 h. Transmission electron microscopy (TEM) revealed similar bimodal distributions of fine and coarse ferrite grains in both cases. However, as expected, the alloy microhardness decreased with increasing in HIPing temperature. Three point bend tests on single edge notched specimens, with a nominal root radius ρ = 0.15 mm, were used to measure the notch fracture toughness, K ρ , as a function of test temperature. The K ρ curves were found to be similar for both processing conditions. It appears that the coarser ferrite grains control cleavage fracture, in a way that is independent of alloy strength and HIPing temperature

  20. Analysis of Institutional Press Releases and its Visibility in the Press

    Directory of Open Access Journals (Sweden)

    José Antonio Alcoceba-Hernando, Ph.D.

    2010-01-01

    Full Text Available The relationships between institutional communication and media communication influence the shaping of social representations of public issues. This research article analyses these relationships based on the case study of the external communication of a public institution, the press releases of Spain’s Youth Institute (Instituto de la Juventud, aka, Injuve, during three years and their repercussion in the press during the same period of time. The results obtained in this research allowed drawing conclusions on the types of communication production of the aforementioned institution and the news treatment of such pieces of information by the printed and digital media. The press releases and the news items were studied using quantitative media content analysis which focused, especially, in referential issues like the information treatment, the thematic analysis, youth representations in the case of the releases; and the visibility of the press releases in the making of news

  1. The antimatter. Press breakfast 23 may 2000

    International Nuclear Information System (INIS)

    Spiro, M.; Dejardin, M.; Debu, P.; Aleksan, R.

    2000-05-01

    This document brings together the subjects discussed during the Press breakfast of 23 may 2000 on the antimatter, with scientists of the CEA and the CNRS. It presents the research programs and the experiments on the antimatter and the symmetry violation: the CP LEAR and the NA48 experiments at CERN, the BaBar detector at SLAC, the fundamental research at the CEA and the impacts on the energy policy. It provides also links for more detailed inquiries. (A.L.B.)

  2. Press conference of the 15 october 2002

    International Nuclear Information System (INIS)

    2002-10-01

    Facing the public hostile purposes of october 2002, concerning the renewable energies, Andre Antolini, President of the renewable energies syndicate, proposed a press conference to give information, data and realizations on the renewable energies. The text of the conference is presented, as data on employment, biofuels, the wind energy, the hydro-electricity the greenhouse effect fight, the public opinion, the solar heating, the photovoltaic and the future projects and electric power supply for 2010. (A.L.B.)

  3. Design of jigs, fixtures and press tools

    CERN Document Server

    Venkataraman, K

    2015-01-01

    Textbook presenting the fundamentals of tool design with special focus on jigs, fixtures and die design Covers sections on sheet metal forming processes; turning, grinding, broaching, welding and modular fixtures; principles of clamping; and an Introduction to Presses and Auxiliary Equipment Author has many years' experience in both academic and industrial environments, and presents this work in an easily-accessible style End of chapter questions and answers assist the learning process for both practicing tooling designers and engineers, and manufacturing en

  4. Natural cold pressed oils as cosmetic products

    Directory of Open Access Journals (Sweden)

    Małgorzata Ligęza

    2016-12-01

    Full Text Available Background. It seems that patients may ask general practitioners about natural cosmetics applied on the skin regarding their safety and suitability. Objectives. The aim of the study was to analyze natural cold pressed oils as potential cosmetic products. Material and methods. Cold pressed oils obtained from selected seeds and fruit stones were analyzed, including: chokeberry seed oil, blackcurrant seed oil, elderberry seed oil, raspberry seed oil, apricot seed oil, tomato seed oil, strawberry seed oil, broccoli seed oil, Nigella sativa seed oil, hemp oil, safflower seed oil, Silybum marianum seed oil and coconut oil. 80 adult volunteers assessed the cosmetic properties of the analyzed oils. Each of the volunteers tested 2 to 4 different oils, by applying them on the skin. In addition, patch tests with all analyzed oils were performed on 23 individuals. Results. The majority of tested oils were positively evaluated by the participants: in the opinion of the participants, oil extracted from safflower had the best appearance (100% positive opinions, coconut oil had the best smell (70% positive opinions, while black currant seed oil showed the best absorbency (85% positive opinions. No irritation was observed within the analyzed product group, albeit one allergic reaction to apricot seed oil was observed with patch testing. Conclusions . Based on the achieved results, it could be suggested that natural cold pressed oils can be applied to the skin as cosmetics. Our observations may be helpful for general practitioners when choosing natural cosmetics.

  5. Hot and cold pressing of (La,Ce)PO4-based nuclear waste forms

    International Nuclear Information System (INIS)

    Floran, R.J.; Rappaz, M.; Abraham, M.M.; Boatner, L.A.

    1981-01-01

    Synthetic analogs of the mineral monazite [(Ce,La,Ca,Th,U)(P,Si)O 4 ] are promising host phases for the isolation of actinide wastes. In the present investigation, the optimal conditions necessary to form high-density, simulated waste pellets from calcined LaPO 4 and CePO 4 powders have been examined. Pellets that are close to the theoretical density are necessary in order to minimize porosity and hence potential avenues along which fluid/waste interactions can take place. Calcined powders prepared by a urea precipitation process were cold pressed and hot pressed under a range of controlled conditions to form coherent, cylindrical pellets. Changes in density were examined as a function of pressure, temperature and duration of sintering. For cold-pressed pellets, a significant increase in density occurs during sintering between 1000 0 C and 1100 0 C. This increase is correlated with substantial grain coarsening of the pellet microstructure. A comparison of cold and hot pressing techniques suggests that, only after sintering, does the density of cold-pressed pellets approach (but not equal) that of the hot-pressed pellets. Densities >90% of the theoretical value of 5.11 g/cm 3 are easily attainable by hot pressing without sintering. The significance of density differences on pellet stability will be investigated in future leaching studies. The apparent advantages of the higher densities achieved by hot pressing must be weighed against the increased technological/engineering complexities involved when working at sustained high temperatures in a remote environment. Thus the cold pressing technique may ultimately prove more practical for large-scale commercial operations

  6. Inter- and intrasubject similarity of muscle synergies during bench press with slow and fast velocity

    DEFF Research Database (Denmark)

    Samani, Afshin; Kristiansen, Mathias

    2018-01-01

    We investigated the effect of low and high bar velocity on inter- and intra-subject similarity of muscle synergies during bench press. Thirteen trained male subjects underwent two exercise conditions, i.e. a slow and a fast velocity bench press. Surface electromyography was recorded from thirteen...... to describe the dataset variability. For the second activation coefficient, the inter-subject similarity within the fast velocity condition was greater than the intra-subject similarity of the activation coefficient across the conditions. An opposite pattern was observed for the first muscle synergy vector...

  7. Effects of Cooking and Screw-Pressing on Functional Properties of Protein in Milkweed (Asclepias spp.) Seed Meals and Press Cakes

    Science.gov (United States)

    This study determined the effects of oil processing conditions on functional properties of milkweed seed proteins to evaluate their potential for value-added uses. Flaked milkweed seeds were cooked at 82 degrees C (180 degrees F) for 30, 60 or 90 min in the seed conditioner, and then screw-pressed ...

  8. Tjekkoslovakisk presse år 2

    Directory of Open Access Journals (Sweden)

    Rudolf Prevratil

    1991-09-01

    Full Text Available Danske teleselskaber overvejer at etablere sig som kabeloperatører i Polen, mens et amerikansk selskab allerede er igang i Warszawa og Krakow. Franske lokalradionetworks opretter filialer i Polen og Tjekko- slovakiet. Den tjekkiske statsradio stiller sendenet til rådighed for Radio Free Europe. Springer-koncernen opretter en "østtysk" pendant til Bild, hvis redaktionelle hovedlinje lægger sig op ad de dybe sociale frustrati- oner, der fulgte med DDR's indlemmelse i BDR. Maxwell, Hersant og Berlusconi m.fl. etablerer sig alene eller med lokale konstellationer inden for trykt presse i flere øst- og mellemeuropæiske stater. Samtidig for- søger den tidligere undergrundspresse at vinde økonomisk og politisk fodfæste inden for markedets og "det legale samfunds" rammer, i kon- kurrence med fortidens mediemutanter og vestlige mediekoncerner. Rudolf Prevratils artikel er en refleksion over en del af de problemer, primært af økonomisk og politisk art, som har tårnet sig op for den tjek- koslovakiske presse efter fløjlsrevolutionen i november 1989. Den giver et billede af dagens situation og får gennem sine analyser påvist, at etab- lingen af en demokratisk presse i Tjekkoslovakiet ikke alene er afhængig af "hjælp udefra", men i nok så høj grad forudsætter et net af sociale og kulturelle udviklingsprocesser, som både anerkender opgøret med for- tiden og vedkender sig den historiske arv. Artiklen er oversat fra engelsk af Per Jauert.

  9. Preparation of tris(8-hydroxyquinolinato)aluminum thin films by sputtering deposition using powder and pressed powder targets

    Science.gov (United States)

    Kawasaki, Hiroharu; Ohshima, Tamiko; Yagyu, Yoshihito; Ihara, Takeshi; Tanaka, Rei; Suda, Yoshiaki

    2017-06-01

    Tris(8-hydroxyquinolinato)aluminum (Alq3) thin films, for use in organic electroluminescence displays, were prepared by a sputtering deposition method using powder and pressed powder targets. Experimental results suggest that Alq3 thin films can be prepared using powder and pressed powder targets, although the films were amorphous. The surface color of the target after deposition became dark brown, and the Fourier transform infrared spectroscopy spectrum changed when using a pressed powder target. The deposition rate of the film using a powder target was higher than that using a pressed powder target. That may be because the electron and ion densities of the plasma generated using the powder target are higher than those when using pressed powder targets under the same deposition conditions. The properties of a thin film prepared using a powder target were almost the same as those of a film prepared using a pressed powder target.

  10. Vibration Control of a High-Speed Precision Servo Numerically Controlled Punching Press: Multidomain Simulation and Experiments

    Directory of Open Access Journals (Sweden)

    Teng Xu

    2017-01-01

    Full Text Available A three-degree-of-freedom mathematical vibration model of a high-speed punching press was developed in order to explore the vibration modes of the punching press. A multidomain model of the punching press was established to predict the kinematic state during different conditions, as well as the effects of load fluctuation on the motor speed. Experimental measurements of the acceleration of the punching press were carried out. The results comparison reveals that the multidomain model is consistent with the vibration model and the experimental measurements. Modal analysis and structure modification of the punching press were conducted. The foundation at the base of the punching press was improved against excess of vibration. The effects of the dimensions of the foundation on the vibration were discussed with the aid of the multidomain model. Finally, proper foundation design, able to reduce the vibration, was obtained.

  11. Press Freedom on the Media Agenda

    OpenAIRE

    Pires, Terezinha Maria de Carvalho Cruz

    2007-01-01

    This article proposes to present a refl ection on the meanings constructed by the Brazilian written press regarding media and democracy. For this, it was necessary to recompose a specifi c journalistic event: the submission to the Brazilian Congress of a bill to create the Federal Journalism Council by the Brazilian President, Luiz Inácio Lula da Silva, at the request of the National Journalists Federation in August, 2004. This procedure gave rise to something rarely seen: the media were in the...

  12. Pocketbook of the economic press 1994

    International Nuclear Information System (INIS)

    Kroll, J.M.

    1994-01-01

    The present 34th edition of this pocketbook gives an overview of German economic journalists with their specific branches, important specialist newspaper editorial boards, the economic editors of the daily-, weekly- and public press, radio and television broadcusting stations as well as news-, information- and teletext services. In addition, 1600 public relations offices of industrial businesses, industry and trade chambers and universities are given. It concludes with information on authorities at a national and county level and more than 1200 business groups and leading bodies. (BWI) [de

  13. WordPress all-in-one for dummies

    CERN Document Server

    Sabin-Wilson, Lisa

    2013-01-01

    Top WordPress guide, now fully updated for the latest WordPress release! This updated new edition comprises one of the largest collections of practical intermediate to advanced information on WordPress. Fully updated for the latest WordPress release, this in-depth book covers it all, from setting up your software to publishing your site, using SEO and social media, developing and using plug-ins, running multiple sites with WordPress, and more. Veteran author Lisa Sabin-Wilson is a top authority on WordPress, and she and her co-authors pack this book with essential and easy-to-follo

  14. Hot-pressing steatite bodies; Obtencion de eseatita por prensado en caliente

    Energy Technology Data Exchange (ETDEWEB)

    Aparicio Arroyo, E

    1967-07-01

    Requirements for some special nuclear engineering ceramic shapes are: big size, impervious, dimensional accuracy and good mechanical and dielectric properties. Limitations of te conventional methods and advantages of te hot pressing techniques for the manufacturing of these shapes are discussed. Hot pressing characteristics of a certain steatite powder are studied. Occurrence of an optimum densification temperature just above the tale decomposition range is found. Experimental data show that the height/diameter ratio of the specimen has no effect on the sintering conditions. Increasing darkness from the graphite mould is detected above the optimum temperature. The hot-pressed steatite is compared with a fired dry-pressed sample of the same composition. (Author) 13 refs.

  15. Effect of an Unstable Load on Primary and Stabilizing Muscles During the Bench Press.

    Science.gov (United States)

    Ostrowski, Stephanie J; Carlson, Lara A; Lawrence, Michael A

    2017-02-01

    Ostrowski, SJ, Carlson, LA, and Lawrence, MA. Effect of an unstable load on primary and stabilizing muscles during the bench press. J Strength Cond Res 31(2): 430-434, 2017-Unstable resistance exercises are performed to increase activity of stabilizing muscles. The premise is that this increase in activity will yield greater strength gains than traditional resistance exercises. The purpose of this study was to determine if an unstable load increases muscle activity of stabilizing muscles during a bench press as compared with a standard bench press with a typical load. Fifteen resistance-trained males (age 24.2 ± 2.7 years, mass 84.8 ± 12.0 kg, height 1.77 ± 0.05 m, weight lifting experience 9.9 ± 3.4 years, and bench press 1 repetition maximum [1RM] 107.5 ± 25.9 kg) volunteered for this study. Subjects pressed 2 sets of 5 repetitions in both stable (75% 1RM) and unstable (60% 1RM) conditions using a standard barbell and a flexible Earthquake bar, respectively. Surface electromyography was used to detect muscle activity of primary movers (pectoralis major, anterior deltoid, and triceps) and stabilizing musculature (latissimus dorsi, middle and posterior deltoid, biceps brachii, and upper trapezius). Muscle activity was compared using a multivariate analysis of variance to determine significant (p ≤ 0.05) phase and condition differences. The right and left biceps and the left middle deltoid were significantly more active in the unstable condition. Some of the stabilizing muscles were found to be significantly more active in the unstable condition with 15% less weight. Therefore, bench pressing with an unstable load appears promising in activating stabilizing musculature compared with pressing a typical barbell.

  16. Clarification of Orange Press Liquors by PVDF Hollow Fiber Membranes

    Directory of Open Access Journals (Sweden)

    Silvia Simone

    2016-01-01

    Full Text Available Press liquors are typical by-products of the citrus juice processing characterized by a high content of organic compounds and associated problems of environmental impact, which imply high treatment costs. However, these wastes contain a great number of health promoting substances, including fibers, carotenoids and phenolic compounds (mainly flavonoids, whose recovery against waste-destruction technologies is very attractive for new business opportunities. In this work, the clarification of orange press liquor by using microfiltration (MF membranes is studied as a preliminary step to obtain a permeate stream enriched in antioxidant compounds which can be further processed to produce extracts of nutraceutical and/or pharmaceutical interest. MF poly(vinylidene fluoride (PVDF hollow fibers were prepared by the dry/wet spinning technique. A series of fibers was produced from the same polymeric dope, in order to investigate the effect of selected spinning parameters, i.e., bore fluid composition and flowrate, on their properties. The morphology of the produced fibers was analyzed by Scanning Electron Microscopy (SEM. Fibers were further characterized for their mechanical properties, porosity, bubble point, pore size distribution and pure water permeability (PWP. Some of the produced fibers exhibited high permeability (pure water permeability ~530 L/m2·h·bar, coupled to good mechanical resistance and pore size in the range of MF membranes. These fibers were selected and used for the clarification of press liquor from orange peel processing. In optimized operating conditions, the selected fibers produced steady-state fluxes of about 41 L/m2·h with rejections towards polyphenols and total antioxidant activity of 4.1% and 1.4%, respectively.

  17. Effect of hot pressing additives on the leachability of hot pressed sodium hydrous titanium oxide

    International Nuclear Information System (INIS)

    Valentine, T.M.; Sambell, R.A.J.

    1980-01-01

    Sodium hydrous titanium oxide is an ion exchange resin which can be used for immobilizing medium level waste (MLW) liquors. When hot pressed, it undergoes conversion to a ceramic. Three low melting point materials (borax, bismuth trioxide, and a mixture of PbO/CuO) were added to the (Na)HTiO and the effect that each of these had on aiding densification was assessed. Hot pressing temperature, applied pressure, and percentage addition of hot pressing aid were varied. Percentage open porosity, flexural strength, and leachability were measured. There was a linear relationship between the percentage open porosity and the logarithm of the leach rate for a constant percentage addition of each additive

  18. The press media and the risk perception

    International Nuclear Information System (INIS)

    Manetti, Cristiane Teixeira

    2009-01-01

    In this study it was identified the frequency of negative and positive news on the nuclear question in the press media. Due to the complexity of the matter, we opt to perform a study case that could illustrate the theoretical discussion presented in this research. Thus, due to the constant presence of news related to IPCC meeting, in the national and foreign press, we opt to focus our study on one year period just after the release of the 4th IPCC Report, in February of 2007. The research was centered only in the printed matters, since there is significant differences between the printed media and others, like TV, radio or web, restricting the use of the same bibliographical reference. In this study it was collected journalistic material involving the nuclear energy and was verified the predominant speech of the vehicles of communication and the sources of information. It was noted the predominance of positive articles, mainly due to the weight of the favorable speeches by authorities, cited as the most frequent in the paper. The negative approach almost always was assumed by the ONGs in general, as expected, due to the its well known position in the treatment of matters related to the nuclear energy. Also it is important to point out that all the tracked vehicles of information mixed positive and negative news articles on the subject; and evidences of hegemonic speech by official sources had been observed. (author)

  19. A CONCEPTUAL APPROACH ON PRESS CONFERENCE

    Directory of Open Access Journals (Sweden)

    Ioana Olariu

    2015-07-01

    Full Text Available A press conference is an important tool of public relations. The primary role of public relations is to manage a company’s reputation and help build public consent for its enterprises. The goal of PR is to develop and maintain goodwill with most, if not all, of its publics. Failure to do so may mean loss of customers and revenues, time lost dealing with complaints or lawsuits, and loss of esteem. A company’s publics change constantly. Well-executed public relations is an ongoing process that molds good long-term relationships and plays an important role in relationship marketing and integrated communications. Companies often call press conference when they have significant news to announce, such as the introduction of a new product or advertising campaign. Although used less often by organizations and corporations, this form of delivery can be very effective. The topic must be of major interest to a specific group before it is likely to gain coverage.

  20. Press Conference: LHC Restart, Season 2

    CERN Multimedia

    CERN. Geneva

    2015-01-01

    PRESS BRIEFING ON THE LARGE HADRON COLLIDER (LHC) RE-START, SEASON 2 AT CERN, GLOBE OF SCIENCE AND INNOVATION Where :   http://cern.ch/directions   at the Globe of Science and Innovation When : Thursday, 12 March from 2.30 to 3.30pm - Open seating as from 2.15pm Speakers : CERN’s Director General, Rolf Heuer and Director of Accelerators, Frédérick Bordry, and representatives of the LHC experiments Webcast : https://webcast.web.cern.ch/webcast/ Dear Journalists, CERN is pleased to invite you to the above press briefing which will take place on Thursday 12 March, in the Globe of Science and Innovation, 1st floor, from 2.30 to 3.30pm. The Large Hadron Collider (LHC) is ready to start up for its second three-year run. The 27km LHC is the largest and most powerful particle accelerator in the world operating at a temperature of -217 degrees Centigrade and powered to a current of 11,000 amps. Run 2 of the LHC follows a two-year technical s...

  1. Preparation and microstructure of hot-pressed YIG

    International Nuclear Information System (INIS)

    Abdul Halim Shaari; Mansor Hashim; Sidek Haji Abd Aziz

    1992-01-01

    Bulk magnetic ceramics such as yttrium-iron-garnet (YIG) and nickel-zinc ferrite were prepared by the conventional-firing and hot-press techniques. Pre-sintering and sintering, both in air, were carried out at temperature ≥ 1200 0 C. Initial density and microstructural measurements show that the high density samples with uniform grain size can be readily achieved by hot-pressing. The well-defined microstructures, the high density attained. The agreement of saturation magnetization 4πMs values and the high resistivities indicated that the optimized preparation conditions for conventional firing yielded yttrium-iron-garnet of good quality. Quenched and isochronally annealed, the YIG samples were also found to retain their room-temperature saturation-magnetization and resonance linewidth values after any single heat treatment. However, the electrical resistivity and the effective linewidth clearly exhibited isochronal recovery. A possible model to explain this behaviour and its implications on microwave applications are discussed. Ferrites of the type MFe 2 O 4 where M=Mg, Mn, Co, Fe, Cu, Zn and Cd and of the type Ni1-2xSnxFe 2 O4 have also been prepared and their properties are being studied

  2. Effects of different vibration exercises on bench press.

    Science.gov (United States)

    Marín, P J; Torres-Luque, G; Hernández-García, R; García-López, D; Garatachea, N

    2011-10-01

    This study was undertaken to analyze the effects of different vibration recovery strategies via feet or hands on the number of repetitions performed and on mean velocity, peak velocity and blood lactate concentration during consecutive bench-press sets. 9 elite judo athletes performed 3 sets of bench press at 60% of one-repetition maximum (1RM), leading to failure and allowing a 180 s rest period between sets. During the rest period, 1 of the 3 following procedures was performed: 150 s rest plus 30 s push-up vibration exercise (Push-up), 150 s rest plus 30 s squat vibration exercise (Squat) or 180 s only rest (Passive). Statistical analysis revealed that the Squat condition resulted in a significant increase in the number of repetitions achieved, in comparison with all other rest strategies. However, kinematic parameters and blood lactate concentration were not affected by vibration. These data suggest that a vibration stimulus applied to the feet, between sets, can result in positive improvements in upper body resistance exercise performance. Although the mechanisms are not fully understood, this positive effect of vibration could be due to an increased motor cortex excitability and voluntary drive. © Georg Thieme Verlag KG Stuttgart · New York.

  3. Fabrication of fully ceramic microencapsulated fuel by hot pressing

    International Nuclear Information System (INIS)

    Lee, H. G.; Kim, D. J; Park, J. Y.; Kim, W. J.; Lee, S. J

    2014-01-01

    Fully ceramic microencapsulated(FCM) nuclear fuel is one of the recently suggested concept to enhance stability nuclear fuel itself. The requirements to increase the accident tolerance of nuclear fuel are mainly two parts: First, the performance has to be maintained compared to the existing UO 2 nuclear fuel and zircaloy cladding system under the normal operation condition. Second, under the severe accident condition, the high temperature structural integrity has to be kept and the generation rate of hydrogen has to be decrease largely. FCM nuclear fuel consists of tristructural isotropic(TRISO) fuel particle and SiC matrix. The relative thermal conductivity of the SiC matrix as compared to UO 2 is quite good, yielding as-irradiated fuel centerline temperature compared to high temperature for the existing fuel leading to reduced stored energy in the core and reduced operational release of fission products from the fuel. Generally SiC ceramics are fabricated via liquid phase sintering due to strong covalent bonding property and low self-diffusivity coefficient. Hot pressing is very effective method to conduct sintering of SiC powder including different second phase. In this study, SiC-matrix composite including TRISO particles were sintered by hot pressing with Al 2 O 3 -Y 2 O 3 additive system. Various sintering condition were investigated to obtain high relative density above 95%. The internal distribution of TRISO particles within SiC-matrix composite was observed by x-ray radiograph. From the analysis of the cross-section of SiC-matrix composite, the fracture of TRISO particles was investigated. In order to uniform distribution of TRISO particle embedded in the SiC matrix, SiC powder overcoating is considered. SiC matrix composite including TRISO was fabricated by hot pressing. FCM pallets with full density were obtained with Al 2 O 3 -Y 2 O 3 additive system. From the microstructure image, the effect of the sintering additive contents and sintering mechanism

  4. Searching for a Free Press in Indian Country.

    Science.gov (United States)

    Benton, Sherrole

    1994-01-01

    Describes the tribally controlled media's efforts to provide a form of checks and balances against the tribal council on behalf of the tribal community. Examines the issue of freedom of the tribal press, suggesting that tribal council's control of press's operating funds may limit press freedom. (MAB)

  5. STS-114: Discovery Launch Readiness Press Conference

    Science.gov (United States)

    2005-01-01

    Michael Griffin, NASA Administrator; Wayne Hale, Space Shuttle Deputy Program Manager; Mike Wetmore, Director of Shuttle Processing; and 1st Lieutenant Mindy Chavez, Launch Weather Officer-United States Air Force 45th Weather Squadron are in attendance for this STS-114 Discovery launch readiness press conference. The discussion begins with Wayne Hale bringing to the table a low level sensor device for everyone to view. He talks in detail about all of the extensive tests that were performed on these sensors and the completion of these ambient tests. Chavez presents her weather forecast for the launch day of July 26th 2005. Michael Griffin and Wayne Hale answer questions from the news media pertaining to the sensors and launch readiness. The video ends with footage of Pilot Jim Kelly and Commander Eileen Collins conducting test flights in a Shuttle Training Aircraft (STA) that simulates Space Shuttle landing.

  6. Inter- and Intrasubject Similarity of Muscle Synergies During Bench Press With Slow and Fast Velocity.

    Science.gov (United States)

    Samani, Afshin; Kristiansen, Mathias

    2018-01-01

    We investigated the effect of low and high bar velocity on inter- and intrasubject similarity of muscle synergies during bench press. A total of 13 trained male subjects underwent two exercise conditions: a slow- and a fast-velocity bench press. Surface electromyography was recorded from 13 muscles, and muscle synergies were extracted using a nonnegative matrix factorization algorithm. The intrasubject similarity across conditions and intersubject similarity within conditions were computed for muscle synergy vectors and activation coefficients. Two muscle synergies were sufficient to describe the dataset variability. For the second synergy activation coefficient, the intersubject similarity within the fast-velocity condition was greater than the intrasubject similarity of the activation coefficient across the conditions. An opposite pattern was observed for the first muscle synergy vector. We concluded that the activation coefficients are robust within conditions, indicating a robust temporal pattern of muscular activity across individuals, but the muscle synergy vector seemed to be individually assigned.

  7. Strength, body composition, and functional outcomes in the squat versus leg press exercises.

    Science.gov (United States)

    Rossi, Fabrício E; Schoenfeld, Brad J; Ocetnik, Skyler; Young, Jonathan; Vigotsky, Andrew; Contreras, Bret; Krieger, James W; Miller, Michael G; Cholewa, Jason

    2018-03-01

    The purpose of this study was to compare strength, body composition, and functional outcome measures following performance of the back squat, leg press, or a combination of the two exercises. Subjects were pair-matched based on initial strength levels and then randomly assigned to 1 of 3 groups: a squat-only group (SQ) that solely performed squats for the lower body; a leg press-only group (LP) that solely performed leg presses for the lower body, or a combined squat and leg press group (SQ-LP) that performed both squats and leg presses for the lower body. All other RT variables were held constant. The study period lasted 10 weeks with subjects performing 2 lower body workouts per week comprising 6 sets per session at loads corresponding to 8-12 RM with 90- to 120-second rest intervals. Results showed that SQ had greater transfer to maximal squat strength compared to the leg press. Effect sizes favored SQ and SQ-LP versus LP with respect to countermovement jump while greater effect sizes for dynamic balance were noted for SQ-LP and LP compared to SQ, although no statistical differences were noted between conditions. These findings suggest that both free weights and machines can improve functional outcomes, and that the extent of transfer may be specific to the given task.

  8. Start up study of UASB reactor treating press mud for biohydrogen production

    International Nuclear Information System (INIS)

    Radjaram, B.; Saravanane, R.

    2011-01-01

    Anaerobic digestion of press mud mixed with water for biohydrogen production was performed in continuous fed UASB bioreactor for 120 days. Experiment was conducted by maintaining constant HRT of 30 h and the volume of biohydrogen evolved daily was monitored. Various parameters like COD, VFA, Alkalinity, EC, Volatile solids, pH with respect to biohydrogen production were monitored at regular interval of time. SBPR was 10.98 ml g -1 COD reduced d -1 and 12.77 ml g -1 VS reduced d -1 on peak yield of biohydrogen. COD reduction was above 70 ± 7%. Maximum gas yield was on the 78th day to 2240 ml d -1 . The aim of the experiment is to study the startup process of UASB reactor for biohydrogen production by anaerobic fermentation of press mud. The inoculum for the process is cow dung and water digested in anaerobic condition for 30 days with municipal sewage sludge. The study explores the viability of biohydrogen production from press mud which is a renewable form of energy to supplement the global energy crisis. -- Highlights: → Feasibility of biohydrogen production from press mud was explored in this study. The gas yield was maximum on the 78th day to 2240 ml d -1 with H 2 % of 52-59%. Biohydrogen yield was about 890 ml kg -1 press mud added d -1 . Press mud is identified as an excellent potential waste to tap energy.

  9. Idealized Compression Ratio for a Screw Briquetting Press

    Directory of Open Access Journals (Sweden)

    Peter Biath

    2012-01-01

    Full Text Available This paper deals with issues in determining the ideal compression ratio for a screw briquetting press. First, the principles of operation and a basic description of the main parts of a screw briquetting press are introduced. The next section describes the pressing space by means of 3D software. The pressing space was created using a Boolean subtract function. The final section of the paper measures the partial volumes of the pressing chamber in CATIA V5 by function of measuring. The measured values are substituted into the formula for the compression ratio, and the resulting evaluations are presented in the diagram in the conclusion of this paper.

  10. Properties of hot pressed MgB2/Ti tapes

    International Nuclear Information System (INIS)

    Kovac, P.; Husek, I.; Melisek, T.; Fedor, J.; Cambel, V.; Morawski, A.; Kario, A.

    2009-01-01

    Hot axial and hot isostatic pressing was applied for single-core MgB 2 /Ti tapes. Differences in transport current density, n-exponents and critical current anisotropy are discussed and related to the grain connectivity influenced by pressing. The magnetic Hall probe scanning measurements allowed observing the isolated regions for axially hot pressed sample attributed to the longitudinally oriented cracks introduced by pressing. The highest current densities were measured for the tape subjected to hot isostatic pressing due to improved connectivity.

  11. Chemical vapor deposition of tantalum on graphite cloth for making hot pressed fiber reinforced carbide-graphite composite

    International Nuclear Information System (INIS)

    Hollabaugh, C.M.; Davidson, K.V.; Radosevich, C.L.; Riley, R.E.; Wallace, T.C.

    1977-01-01

    Conditions for the CVD of a uniform coating of Ta on fibers of a woven graphite cloth were established. The effect of gas composition, pressure, and temperature were investigated, and the conditions that gave the desired results are presented. Several layers of the coated cloth were hot pressed to produce a TaC--C composite having uniformly dispersed, fine-grained TaC in graphite. Three compositions were hot pressed: 15, 25, and 40 volume percent carbide. 8 figures, 2 tables

  12. Press/Pulse: Explaining selective terrestrial extinctions at the Cretaceous/Palaeogene boundary

    Science.gov (United States)

    Arens, Nan Crystal

    2010-05-01

    Single-cause mass extinction scenarios require extreme conditions to generate sufficiently strong kill mechanisms. Such dire effects are commonly at odds with the taxonomic selectivity that characterizes most extinction events. In response, some researchers have proposed that the interaction of a variety of factors typify episodes of elevated extinction. Previous work (Arens & West 2008 Paleobiology 34:456-471) has shown that a combination of press and pulse disturbances increases the probability of elevated extinction. The press/pulse contrast is borrowed from community ecology, where researchers have long recognized that the ecological response to long-term stress differs from that of an instantaneous catastrophe. Scaled to the macroevolutionary level, press disturbances alter community composition by placing multigenerational stress on populations. Press disturbances do not necessarily cause mortality, but reduce population size by a variety of mechanisms such as curtailed reproduction. Pulse disturbances are sudden catastrophic events that cause extensive mortality. Either press or pulse disturbances of sufficient magnitude can cause extinction, however elevated extinction occurs more commonly during the coincidence of lower-magnitude press and pulse events. The Cretaceous/Palaeogene (K/P) extinction is one of the best examples of a press/pulse extinction. Deccan Trap volcanism, which straddled the K/P boundary, altered atmospheric composition and climate. This episodic volcanism likely contributed to the climate instability observed in terrestrial ecosystems and exerted press stress. Pulse disturbance was produced by bolide impact, which punctuated the end of the Cretaceous. The press/pulse mechanism also more effectively explains selectivity in terrestrial vertebrate and plant extinctions at the K/P boundary than do single-mechanisms scenarios. For example, why do environmentally sensitive vertebrates such as amphibians experience no extinction? And why do

  13. Treatment of the press residues of pressed grapes on an industrial scale

    Energy Technology Data Exchange (ETDEWEB)

    1978-04-24

    EtOH and tartaric acid are recovered from press residues of grapes by distillation and concentration of the EtOH and extraction of the dried residue after removal of seeds with a mixture of H/sub 2/O and mineral acid. Vegetable oil is extracted from the seeds. Collidal substances are coagulated by roasting prior to extraction of tartaric acid. The grape skins are recovered in flake form.

  14. Press conference of the 15 october 2002; Conference de presse du 15 octobre 2002

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-10-01

    Facing the public hostile purposes of october 2002, concerning the renewable energies, Andre Antolini, President of the renewable energies syndicate, proposed a press conference to give information, data and realizations on the renewable energies. The text of the conference is presented, as data on employment, biofuels, the wind energy, the hydro-electricity the greenhouse effect fight, the public opinion, the solar heating, the photovoltaic and the future projects and electric power supply for 2010. (A.L.B.)

  15. Hot isostatic press waste option study report

    International Nuclear Information System (INIS)

    Russell, N.E.; Taylor, D.D.

    1998-02-01

    A Settlement Agreement between the Department of Energy and the State of Idaho mandates that all high-level radioactive waste now stored at the Idaho Chemical Processing Plant be treated so that it is ready to move out of Idaho for disposal by the target date of 2035. This study investigates the immobilization of all Idaho Chemical Processing Plant calcine, including calcined sodium bearing waste, via the process known as hot isostatic press, which produces compact solid waste forms by means of high temperature and pressure (1,050 C and 20,000 psi), as the treatment method for complying with the settlement agreement. The final waste product would be contained in stainless-steel canisters, the same type used at the Savannah River Site for vitrified waste, and stored at the Idaho National Engineering and Environmental Laboratory until a national geological repository becomes available for its disposal. The waste processing period is from 2013 through 2032, and disposal at the High Level Waste repository will probably begin sometime after 2065

  16. [Work disability in public press professions].

    Science.gov (United States)

    Akermann, S

    2002-09-01

    In this study more than 1,000 cases of long-term disability among members of the press and media were evaluated. Mental disorders were the main cause of disability in almost every fourth case. In women psychiatric illnesses were even more important. The most common diagnosis was that of a depressive disorder which accounted for more than half of all psychiatric cases. The causes of disability of other insurance systems such as the German social security scheme and the pension and disability plan for the medical profession were compared. Mental illnesses are the leading cause of disability in white collar workers and orthopaedic illnesses, especially disorders of the vertebral column, are the leading cause in blue collar workers, as one might have expected. In females mental disorders are even more common than in men whereas men tend to have more cardiovascular problems than women. In this study also some interesting features regarding disability caused by various illnesses after long-term follow-up were found. This opens unknown perspectives allowing new assessment of diseases and eventually will enable the actuary to price medical diagnoses for disability insurance.

  17. Pressing problems of measurement of ionizing radiations

    International Nuclear Information System (INIS)

    Fominykh, V.I.; Yudin, M.F.

    1993-01-01

    The current system for ensuring the unity of measurements in the Russian Federation and countries of the former Soviet Union ensures a high quality of dosimetric, radiometric, and spectrometric measurements in accordance with the recommendations of the Consulative Committee on Standards for Measurements of Ionizing Radiations of the International Bureau of Weights and Measures (IBWM), International Organization on Radiological Units (ICRU), International Commission on Radiological Protection (ICRP), International Organization on Legislative Metrology (IOLM), International Atomic Energy Agency (IAEA), World Health Organization (WHO), etc. Frequent collation of the national primary and secondary standards of Russia with those of IBWM and the leading national laboratories of the world facilitate mutual verification of the measurements of ionizing radiations. The scope of scientific and scientific-technical problems that can be solved by using ionizing radiations has expanded significantly in recent years. In this paper the authors consider some pressing problems of the metrology of ionizing radiations which have arisen as a result of this expansion. These include the need for unity and reliability of measurements involved in radiation protection, the measurement of low doses involving low dose rates, ensuring the unity of measurements when monitoring the radiological security of the population, the need for more uniformity on an international scale regarding the basic physical quantities and their units for characterizing radiation fields, determination of the accuracy of measurement of the radiation dose absorbed by an irradiated tissue or organ, and the development of complex standards for ionizing radiations. 5 refs., 1 tab

  18. Hot isostatic press waste option study report

    Energy Technology Data Exchange (ETDEWEB)

    Russell, N.E.; Taylor, D.D.

    1998-02-01

    A Settlement Agreement between the Department of Energy and the State of Idaho mandates that all high-level radioactive waste now stored at the Idaho Chemical Processing Plant be treated so that it is ready to move out of Idaho for disposal by the target date of 2035. This study investigates the immobilization of all Idaho Chemical Processing Plant calcine, including calcined sodium bearing waste, via the process known as hot isostatic press, which produces compact solid waste forms by means of high temperature and pressure (1,050 C and 20,000 psi), as the treatment method for complying with the settlement agreement. The final waste product would be contained in stainless-steel canisters, the same type used at the Savannah River Site for vitrified waste, and stored at the Idaho National Engineering and Environmental Laboratory until a national geological repository becomes available for its disposal. The waste processing period is from 2013 through 2032, and disposal at the High Level Waste repository will probably begin sometime after 2065.

  19. Distal clavicular osteolysis in adults: association with bench pressing intensity

    International Nuclear Information System (INIS)

    Nevalainen, Mika T.; Morrison, William B.; Zoga, Adam C.; Roedl, Johannes B.; Ciccotti, Michael G.

    2016-01-01

    To investigate the association between distal clavicular osteolysis (DCO) and bench pressing intensity. From a retrospective review of MRI shoulder reports of individuals between 20 and 40 years of age, 262 male patients with DCO and 227 age-matched male patients without DCO were selected. All patients had completed a bench pressing questionnaire. The patients' bench pressing frequency (times per week), duration (years of bench pressing), bench pressing weight (maximum bench pressing weight with one repetition = 1RM) and the ratio of bench pressing weight to body weight were compared between both groups using Chi-square and Mann-Whitney tests. The results showed that 56 % (146/262) of patients with DCO were high-intensity bench pressers (1RM more than 1.5 times the body weight) compared to 6 % (14/227) in patients without DCO. High-intensity bench pressing was a risk factor for DCO (OR = 19; 95 %CI = 11-35; p 1 x /week) and duration (>5 years) of bench pressing were risk factors. In bench pressers who suffered from DCO, the mean 1RM was 283 lbs (±SD 57) compared to 209 lbs (±SD 60) in bench pressers not affected by DCO (p < 0.001, Mann-Whitney). High-intensity, but not low-intensity bench pressing is a risk factor for DCO. (orig.)

  20. Tantalum powder consolidation, modeling and properties

    International Nuclear Information System (INIS)

    Bingert, S.R.; Vargas, V.D.; Sheinberg, H.C.

    1996-01-01

    A systematic approach was taken to investigate the consolidation of tantalum powders. The effects of sinter time, temperature and ramp rate; hot isostatic pressing (HIP) temperature and time; and powder oxygen content on consolidation density, kinetics, microstructure, crystallographic texture, and mechanical properties have been evaluated. In general, higher temperatures and longer hold times resulted in higher density compacts with larger grain sizes for both sintering and HIP'ing. HIP'ed compacts were consistently higher in density than sintered products. The higher oxygen content powders resulted in finer grained, higher density HIP'ed products than the low oxygen powders. Texture analysis showed that the isostatically processed powder products demonstrated a near random texture. This resulted in isotropic properties in the final product. Mechanical testing results showed that the HIP'ed powder products had consistently higher flow stresses than conventionally produced plates, and the sintered compacts were comparable to the plate material. A micromechanics model (Ashby HIP model) has been employed to predict the mechanisms active in the consolidation processes of cold isostatic pressing (CIP), HIP and sintering. This model also predicts the density of the end product and whether grain growth should be expected under the applied processing conditions

  1. A Pedagogical Route for the Reading of the Press Opinion Article

    Directory of Open Access Journals (Sweden)

    Niura Maria Fontana

    2011-07-01

    Full Text Available A teaching sequence for the university level, focusing on the press opinion article as a genre, based on genre assumptions (Bakhtin, 1992, Bronckart, 2003 and on teaching sequences (Dolz, Noverraz e Schneuwly, 2004, comprehends the following activities: pre-reading (previous knowledge activation; hypotheses raising; reading (production conditions; constitution of text meaning; reading strategies; post-reading (relationships between text and reality; critical awareness. These were followed by chain genres production (press opinion article and related genres, promoting interaction among text, reader and writer, complemented by metacognitive reflection. Applied to two groups of freshmen, the sequence showed statistically significant results in the development of reading competence.

  2. Auxiliary equipment and special techniques used for hot isostatic pressing

    International Nuclear Information System (INIS)

    Pfeffer, J.B.; Odebo, U.

    1977-01-01

    The largest use for hot isostatic pressing (HIP) in production is in the consolidation of powder. In principle, powder is filled into a capsule of metal or glass, and the capsule is evacuated, sealed and loaded into the hot isostatic press. Consolidation takes place in the hot isostatic press, at which time the consolidated capsule is removed from the press and the encapsulation material is removed from the consolidated powder body. In both densification and defect healing, HIP is carried out without encapsulating the material. This is possible as the materials that lend themselves to HIP healing initially have a high density without communicating pores; therefore, the material acts as its own capsule. Considerations outside of the hot isostatic press that must be taken into account are examined. Information is included on powder manufacture, fabrication of capsules, powder handling, capsule sealing, and loading and unloading the press

  3. High density high-TC ceramic superconductors by hot pressing

    International Nuclear Information System (INIS)

    Mak, S.; Chaklader, A.C.D.

    1989-01-01

    High density and high T C superconductor specimens, YBa 2 Cu 3 O x , have been produced by hot-pressing. The factors studied are the effect of hot pressing on the density, the oxygen stoichiometry, the crystal structure, and the critical temperature. Hot pressing followed by heat treatment increased the density of the specimen to 93%. The hot pressing itself did not significantly affect the oxygen content in the specimen, and although the crystal structure appeared to be orthorhombic, the specimens were not superconducting above liquid nitrogen temperature. The superconductivity was restored after head treatment in oxygen. The highest critical temperature (T C ) of the hot pressed pellets was 82K, which was slightly lower than the T C that could be obtained with the cold pressed/sintered pellets. (6 refs., 5 figs., tab.)

  4. Direct drive digital servo press with high parallel control

    Science.gov (United States)

    Murata, Chikara; Yabe, Jun; Endou, Junichi; Hasegawa, Kiyoshi

    2013-12-01

    Direct drive digital servo press has been developed as the university-industry joint research and development since 1998. On the basis of this result, 4-axes direct drive digital servo press has been developed and in the market on April of 2002. This servo press is composed of 1 slide supported by 4 ball screws and each axis has linearscale measuring the position of each axis with high accuracy less than μm order level. Each axis is controlled independently by servo motor and feedback system. This system can keep high level parallelism and high accuracy even with high eccentric load. Furthermore the 'full stroke full power' is obtained by using ball screws. Using these features, new various types of press forming and stamping have been obtained by development and production. The new stamping and forming methods are introduced and 'manufacturing' need strategy of press forming with high added value and also the future direction of press forming are also introduced.

  5. The development of a repetition-load scheme for the eccentric-only bench press exercise.

    Science.gov (United States)

    Moir, Gavin L; Erny, Kyle F; Davis, Shala E; Guers, John J; Witmer, Chad A

    2013-01-01

    The purpose of the present study was to develop a repetition-load scheme for the eccentric-only bench press exercise. Nine resistance trained men (age: 21.6 ± 1.0 years; 1-repetition maximum [RM] bench press: 137.7 ± 30.4 kg) attended four testing sessions during a four week period. During the first session each subject's 1-RM bench press load utilizing the stretch-shortening cycle was determined. During the remaining sessions they performed eccentric-only repetitions to failure using supra-maximal loads equivalent to 110%, 120% and 130% of their 1-RM value with a constant cadence (30 reps·min(-1)). Force plates and a three dimensional motion analysis system were used during these final three sessions in order to evaluate kinematic and kinetic variables. More repetitions were completed during the 110% 1-RM condition compared to the 130% 1-RM condition (p=0.01). Mean total work (p=0.046) as well as vertical force (p=0.049), vertical work (p=0.017), and vertical power output (p=0.05) were significantly greater during the 130% 1-RM condition compared to the 110% 1-RM condition. A linear function was fitted to the number of repetitions completed under each load condition that allowed the determination of the maximum number of repetitions that could be completed under other supra-maximal loads. This linear function predicted an eccentric-only 1-RM in the bench press with a load equivalent to 164.8% 1-RM, producing a load of 227.0 ± 50.0 kg. The repetition-load scheme presented here should provide a starting point for researchers to investigate the kinematic, kinetic and metabolic responses to eccentric-only bench press workouts.

  6. Conditioning processes for incinerator ashes

    International Nuclear Information System (INIS)

    Jouan, A.; Ouvrier, N.; Teulon, F.

    1990-01-01

    Three conditioning processes for alpha-bearing solid waste incineration ashes were investigated and compared according to technical and economic criteria: isostatic pressing, cold-crucible direct-induction melting and cement-resin matrix embedding

  7. Citizen Journalism in Cyber Media: Protection and Legal Responsibility Under Indonesian Press Law

    Directory of Open Access Journals (Sweden)

    Vidya Prahassacitta

    2017-01-01

    Full Text Available Phenomena of citizen journalism had accepted and become part of cyber media. Cyber media owned and managed by press companies had featured citizen journalists’ information, critics, opinions, and news. Citizen journalism was part of freedom of expression. However, in Indonesia’s press law concept, it was not part of the national press. This created legal issues regarding protection and legal responsibility aspects for both parties. A qualitative research was conducting to solving these issues. Using secondary data from literature study and observation on several cyber media websites, this discovers two conclusions. First, the citizen journalist is part of freedom of the press; it means that a citizen journalist’s creation has protected form censor and bans. However, a citizen journalist still has a limitation which shall be complied videlicet Civil Code and Law No. 11 The year 2008 concerning Information and Electronic Transaction. Violation of both regulations means that a citizen journalist shall be legally responsible. Second, protection and responsibility border between a citizen journalist and press company are based on an agreement. Approval of term and condition of general user content in a website from a citizen journalist means that both parties have agreed to enter into an agreement. A press company might be freed of its legal responsibility as long as conducted its obligation to control and manage contents that have been uploaded and published by a citizen journalist. If the company does not take proportional action against citizen journalist’ contents that violating the law, the press company shall be requested its civil or criminal legal responsibility.

  8. A comparison of muscle activity in concentric and counter movement maximum bench press.

    Science.gov (United States)

    van den Tillaar, Roland; Ettema, Gertjan

    2013-01-01

    The purpose of this study was to compare the kinematics and muscle activation patterns of regular free-weight bench press (counter movement) with pure concentric lifts in the ascending phase of a successful one repetition maximum (1-RM) attempt in the bench press. Our aim was to evaluate if diminishing potentiation could be the cause of the sticking region. Since diminishing potentiation cannot occur in pure concentric lifts, the occurrence of a sticking region in this type of muscle actions would support the hypothesis that the sticking region is due to a poor mechanical position. Eleven male participants (age 21.9 ± 1.7 yrs, body mass 80.7 ± 10.9 kg, body height 1.79 ± 0.07 m) conducted 1-RM lifts in counter movement and in pure concentric bench presses in which kinematics and EMG activity were measured. In both conditions, a sticking region occurred. However, the start of the sticking region was different between the two bench presses. In addition, in four of six muscles, the muscle activity was higher in the counter movement bench press compared to the concentric one. Considering the findings of the muscle activity of six muscles during the maximal lifts it was concluded that the diminishing effect of force potentiation, which occurs in the counter movement bench press, in combination with a delayed muscle activation unlikely explains the existence of the sticking region in a 1-RM bench press. Most likely, the sticking region is the result of a poor mechanical force position.

  9. Dynamic modeling and experiment of a new type of parallel servo press considering gravity counterbalance

    Science.gov (United States)

    He, Jun; Gao, Feng; Bai, Yongjun; Wu, Shengfu

    2013-11-01

    The large capacity servo press is traditionally realized by means of redundant actuation, however there exist the over-constraint problem and interference among actuators, which increases the control difficulty and the product cost. A new type of press mechanism with parallel topology is presented to develop the mechanical servo press with high stamping capacity. The dynamic model considering gravity counterbalance is proposed based on the virtual work principle, and then the effect of counterbalance cylinder on the dynamic performance of the servo press is studied. It is found that the motor torque required to operate the press is a lot less than the others when the ratio of the counterbalance force to the gravity of ram is in the vicinity of 1.0. The stamping force of the real press prototype can reach up to 25 MN on the position of 13 mm away from the bottom dead center. The typical deep-drawing process with 1 200 mm stroke at 8 strokes per minute is proposed by means of five order polynomial. On this process condition, the driving torques are calculated based on the above dynamic model and the torque measuring test is also carried out on the prototype. It is shown that the curve trend of calculation torque is consistent to the measured result and that the average error is less than 15%. The parallel mechanism is introduced into the development of large capacity servo press to avoid the over-constraint and interference of traditional redundant actuation, and its dynamic characteristics with gravity counterbalance are presented.

  10. Legal Protection To The Infotainment Of Press Development In Indonesia

    Directory of Open Access Journals (Sweden)

    Anwar Fuadi

    2015-08-01

    Full Text Available Abstract In the socio-political life the press has become an integral part in democratic life. The press has become one of the means for citizens to bring their thoughts and opinions. Nowadays there is a tendency to increase the quantity of press publications sharp but not accompanied by a statement of the quality of journalism. The objective of this research is to understand the essence of the infotainment liability as a mass media in order to construct a freedom of the press principle which has legitimacy within the legal system of the press in Indonesia. The type of research used in this paper is normative research or also known as doctrinal research by reviewing the legal protection to the infotainment as a mass media in Indonesia. The outcomes of the research indicate that the role of infotainment in the legal system of the press in Indonesia refers to the legal construction of institutional and infotainment organizers itself. Legal liability of Infotainment essentially can be seen from the press obligations stipulated in the Law No. 40 of 1999 regarding the Press Law No. 32 of 2002 regarding Broadcasting as well as the Journalists Code of Ethics which support freedom of the press and expression.

  11. The small academic press in the land of giants

    Directory of Open Access Journals (Sweden)

    Frances Pinter

    2015-11-01

    Full Text Available Mergers and acquisitions, for example the merger of Macmillan Science and Education with Springer Science+Business Media, might suggest that large is the future for academic publishing.  It might seem that giant players will dominate the future of scholarly publishing, but, at the same time, this year has seen the launch of UCL Press, the University’s in-house publishing arm. Goldsmiths, University of London, has also announced it is preparing to launch Goldsmiths Press, a new university press built on digital-first publishing, especially around unconventional projects traditionally excluded by publishers. Some of the more established university presses also seem to be increasing their scope. For example, Stanford University Press launched a new trade imprint and Manchester University Press has announced it has acquired forward titles from Bloomsbury Publishing.  'Insights 'asked two experts if there really is scope for the small academic press in the modern scholarly publishing environment. Frances Pinter has provided the perspective of the small university press. She is realistic about the challenges small academic publishers face, but concludes that there is space and opportunity for them to coexist with the giants. Michael Magoulias is equally realistic about the challenges of small, but sees the university press as a necessary, not to say, vital, alternative to commercial publishing.

  12. WordPress all-in-one for dummies

    CERN Document Server

    Sabin-Wilson, Lisa; Palmer, Kevin

    2011-01-01

    A convenient how-to guide for maximizing your WordPress experience. WordPress is a state-of-the-art blog publishing platform with nearly ten million active installations. Eight minibooks provide you with expanded coverage of the most important topics to the WordPress community, such as WordPress basics, theme designs, plug-in development, social media integration, SEO, customization, and running multiple sites. Veteran author Lisa Sabin-Wilson leads an authoritative team of authors who offer their unique knowledge and skillset while sharing invaluable advice for maximizing your site's potentia

  13. Simplex network modeling for press-molded ceramic bodies incorporated with granite waste

    International Nuclear Information System (INIS)

    Pedroti, L.G.; Vieira, C.M.F.; Alexandre, J.; Monteiro, S.N.; Xavier, G.C.

    2012-01-01

    Extrusion of a clay body is the most commonly applied process in the ceramic industries for manufacturing structural block. Nowadays, the assembly of such blocks through a fitting system that facilitates the final mounting is gaining attention owing to the saving in material and reducing in the cost of the building construction. In this work, the ideal composition of clay bodies incorporated with granite powder waste was investigated for the production of press-molded ceramic blocks. An experimental design was applied to determine the optimum properties and microstructures involving not only the precursors compositions but also the press and temperature conditions. Press load from 15 ton and temperatures from 850 to 1050°C were considered. The results indicated that varying mechanical strength of 2 MPa to 20 MPa and varying water absorption of 19% to 30%. (author)

  14. Generation of stress-strain state in combined strip pile foundation beds through pressing of soil

    Directory of Open Access Journals (Sweden)

    Stepanov Maxim

    2017-01-01

    Full Text Available When erecting high-rise buildings, weak underlying soils cause a number of problems in design and construction. In order to ensure the required non-exceedance of the ultimate limit settlements, the combined strip pile foundation has been developed allowing the soil bed to be pre-stressed. This is achieved by injection of pressurized mortar (pressing. The paper analyzes the effect of soil pre-stressing followed by pressing of foundation with the cement mortar, as applied to existing structures using the Plaxis 3D software package in conditions of volume deformation and the Hardening Soil Model. Variable order of foundation pressing allows the required parameters of soil bed to be achieved in plan and depth, thus improving interaction with the foundation and superstructure.

  15. Effects of whole-body vibration applied to lower extremity muscles during decline bench press exercise.

    Science.gov (United States)

    García-Gutiérrez, M T; Hazell, T J; Marín, P J

    2016-09-07

    To evaluate the effects of whole-body vibration (WBV) on skeletal muscle activity and power performance of the upper body during decline bench press exercise at different loads. Forty-seven healthy young and active male students volunteered. Each performed dynamic decline bench press repetitions with and without WBV (50 Hz, 2.2 mm) applied through a hamstring bridge exercise at three different loads of their 1-repetition maximum (1RM): 30%, 50%, and 70% 1RM. Muscle activity of the triceps brachii (TB), biceps brachii (BB), pectoralis major (PM), and biceps femoris (BF) was measured with surface electromyography electrodes and kinetic parameters of the repetitions were measured with a rotary encoder. WBV increased peak power (PP) output during the 70% 1RM condition (pbench press and this augmentation contributes to an increased peak power at higher loads and increased peak acceleration at lower loads.

  16. To bind or not to bind? Different temporal binding effects from voluntary pressing and releasing actions.

    Science.gov (United States)

    Zhao, Ke; Chen, Yu-Hsin; Yan, Wen-Jing; Fu, Xiaolan

    2013-01-01

    Binding effect refers to the perceptual attraction between an action and an outcome leading to a subjective compression of time. Most studies investigating binding effects exclusively employ the "pressing" action without exploring other types of actions. The present study addresses this issue by introducing another action, releasing action or the voluntary lifting of the finger/wrist, to investigate the differences between voluntary pressing and releasing actions. Results reveal that releasing actions led to robust yet short-lived temporal binding effects, whereas pressing condition had steady temporal binding effects up to super-seconds. The two actions also differ in sensitivity to changes in temporal contiguity and contingency, which could be attributed to the difference in awareness of action. Extending upon current models of "willed action," our results provide insights from a temporal point of view and support the concept of a dual system consisting of predictive motor control and top-down mechanisms.

  17. Effects of lesions of the amygdala central nucleus on autoshaped lever pressing

    Science.gov (United States)

    Chang, Stephen E.; Wheeler, Daniel S.; Holland, Peter C.

    2012-01-01

    Neutral cues paired with rewards often appear to acquire motivational significance, as if the incentive motivational value of the reward is transferred to the cue. Such cues have been reported to modulate the performance of instrumental action (Pavlovian-instrumental transfer, PIT), serve as conditioned reinforcers in the establishment of new learning, and be the targets of approach and other cue-directed behaviors. Here we examined the effects of lesions of the amygdala central nucleus (CeA) on the acquisition of discriminative autoshaped lever-pressing. Insertion of one lever into the experimental chamber was reinforced by sucrose delivery, but insertion of another lever was not reinforced. Although sucrose delivery was not contingent on lever pressing, both CeA- and sham-lesioned rats rapidly came to press the reinforced but not the nonreinforced lever. Despite their showing little evidence of impairments in autoshaped lever pressing, these same CeA-lesioned rats showed significant deficits in the expression of PIT in a subsequent phase of the experiment. The lack of impaired autoshaping in CeA-lesioned rats contrasts with effects previously reported for conditioned orienting responses (ORs) and for other putative measures of incentive learning including PIT and conditioned approach to visual cues. PMID:22386516

  18. Fretting wear simulation of press-fitted shaft with finite element analysis and influence function method

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dong Hyong; Kwon, Seok Jin [Korea Railroad Research Institute, Uiwang (Korea, Republic of); Choi, Jae Boong; Kim, Young Jin [Sungkyunkwan University, Suwon (Korea, Republic of)

    2008-01-15

    In this paper the fretting wear of press-fitted specimens subjected to a cyclic bending load was simulated using finite element analysis and numerical method. The amount of microslip and contact variable at press-fitted and bending load condition in a press-fitted shaft was analysed by applying finite element method. With the finite element analysis result, a numerical approach was applied to predict fretting wear based on modified Archard's equation and updating the change of contact pressure caused by local wear with influence function method. The predicted wear profiles of press-fitted specimens at the contact edge wear compared with the experimental results obtained by rotating bending fatigue tests. It is shown that the depth of fretting wear by repeated slip between shaft and boss reaches the maximum value at the contact edge. The initial surface profile is continuously changed by the wear at the contact edge, and then the corresponding contact variables are redistributed. The work establishes a basis for numerical simulation of fretting wear on press fits.

  19. Fretting wear simulation of press-fitted shaft with finite element analysis and influence function method

    International Nuclear Information System (INIS)

    Lee, Dong Hyong; Kwon, Seok Jin; Choi, Jae Boong; Kim, Young Jin

    2008-01-01

    In this paper the fretting wear of press-fitted specimens subjected to a cyclic bending load was simulated using finite element analysis and numerical method. The amount of microslip and contact variable at press-fitted and bending load condition in a press-fitted shaft was analysed by applying finite element method. With the finite element analysis result, a numerical approach was applied to predict fretting wear based on modified Archard's equation and updating the change of contact pressure caused by local wear with influence function method. The predicted wear profiles of press-fitted specimens at the contact edge wear compared with the experimental results obtained by rotating bending fatigue tests. It is shown that the depth of fretting wear by repeated slip between shaft and boss reaches the maximum value at the contact edge. The initial surface profile is continuously changed by the wear at the contact edge, and then the corresponding contact variables are redistributed. The work establishes a basis for numerical simulation of fretting wear on press fits

  20. Fabrication of large Ti–6Al–4V structures by direct laser deposition

    Energy Technology Data Exchange (ETDEWEB)

    Qiu, Chunlei; Ravi, G.A. [School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom); Dance, Chris; Ranson, Andrew; Dilworth, Steve [Integrated Operations, Manufacturing & Materials Engineering Department, BAE Systems Ltd (United Kingdom); Attallah, Moataz M., E-mail: m.m.attallah@bham.ac.uk [School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom)

    2015-04-25

    Highlights: • High laser power and a reasonably low powder feed rate are key to low porosity. • Scaling-up of samples requires smaller Z steps to achieve geometrical integrity. • HIPing effectively closed pores, changed microstructure and improved ductility. • Optimised processing conditions plus HIPing led to good quality Ti-64 structures. • HIPing helps recover shape of unclamped large structures from distortion. - Abstract: Ti–6Al–4V samples have been prepared by direct laser deposition (DLD) using varied processing conditions. Some of the as-fabricated samples were stress-relieved or hot isostatically pressed (HIPed). The microstructures of all the samples were characterised using optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) and the tensile properties assessed. It was found that a high laser power together with a reasonably low powder feed rate was essential for achieving minimum porosity. The build height and geometrical integrity of samples were sensitive to the specified laser nozzle moving step along the build height direction (or Z step) with a too big Z step usually leading to a build height smaller than specified height (or under build) and a too small Z step to excessive building (or excess build). Particularly, scaling-up of samples requires a smaller Z step to obtain specified build height and geometry. The as-fabricated microstructure was characterised by columnar grains together with martensitic needle structure and a small fraction of β phase. This led generally to high tensile strengths but low elongations. The vertically machined samples showed even lower elongation than horizontally machined ones due to the presence of large lack-of-fusion pores at interlayer interfaces. HIPing effectively closed pores and fully transformed the martensites into lamellar α + β phases, which considerably improved ductility but caused slight reduction in strength. With optimisation of processing conditions

  1. Effects of pressing temperature and initial microstructure on the equal channel angular pressing of Ti-6Al-4V alloy

    International Nuclear Information System (INIS)

    Ko, Y.G.; Lee, Y.H.; Jung, W.S.; Shin, D.H.; Lee, C.S.

    2003-01-01

    The effects of pressing temperature and initial microstructure on the equal channel angular (ECA) pressing of Ti-6Al-4V alloy were investigated in this study. The ECA pressing was carried out isothermally with route C at 500 C, 600 C and 700 C for two typical microstructures, i.e., the Widmanstaetten microstructure and the equiaxed microstructure. The results showed that ECA pressing at 600 C and 700 C was successful without producing any noticeable segment at the specimen surfaces, while a large amount of surface segments were produced at 500 C. After 1 pass pressing at 600 C, the equiaxed microstructure showed more uniform material flow at the surface than the Widmanstaetten microstructure. However, this microstructural influence was diminished with increase of the number of the ECA pressing. A flow-localization parameter that quantifies the flow non-uniform tendency in case of flow softening materials was used to explain the different results in each microstructure. (orig.)

  2. Characterization of hot isostatically pressed Bi-Sr-Ca-Cu-O as a function of consolidation variables

    International Nuclear Information System (INIS)

    Goretta, K.C.; Miller, D.J.; Poeppel, R.B.; Nash, A.S.

    1992-01-01

    This paper reports that fully dense, bulk Bi 2 Sr 1.7 CaCu 2 O x superconductor pellets were made by hot isostatic pressing in an inert atmosphere. Electron microscopy revealed that rotation and bending of the platelike 2212 grains were responsible for much of the densification. Under processing conditions of 825 degrees C and 105 MPa, dense pellets were obtained in 15 min. Many dislocations, planar faults, and, perhaps, intergrowths of the Bi 2 Cr 2 CuO x phase were produced during pressing. The dislocations were largely present in subgrain boundaries when the pressing times were increased to 45-120 min

  3. The LNG industry in 2011. Press revue

    International Nuclear Information System (INIS)

    2012-05-01

    The outlook of the LNG industry in 2011 is presented as a revue of press articles: The role of LNG as a flexible and secure energy source as well as the prompt response to provide back-up through additional supplies and cargo diversions to compensate for the sudden loss of nuclear capacity in Japan - with sellers exercising due price restraint in view of the human tragedy - has been a credit to the industry. The increase in production capacity in 2009 and 2010, in particular from Qatar, had permitted the necessary buffer to cope much better with the demand surge than during past disruptions (such as the aftermath of the Chuetsu earthquake in late 2007). Undoubtedly, the marked shift over the last decade in the industry's prevailing business model towards global trade, destination flexibility and portfolio play has also facilitated the rapid response. As the total volume of LNG trade is very much determined by the availability of supply, 2011 has seen a growth of 9.4% over 2010, mainly as a result of the full availability of the six Qatar mega-trains over the past year. On the demand side the two traditional basins have shown very contrasting trends: 15% higher LNG off-take in Asia (the five major markets all increasing between 37.4% and 8.9%), versus a 1.7% decrease in the Atlantic Basin. Cargo diversions and an increasing number of reloads have boosted the exports from the Atlantic Basin to Asia in 2011 to more than 14 million tons (equivalent to more than 200 large size cargoes). Remarkable is also the fast growth in new markets in Latin America and in the Middle East - albeit from a small base - with counter-seasonal but varying demand, offering attractive arbitrage opportunities to portfolio play. Not surprising then that 2011 has seen another hike in spot and short-term trade, not just in absolute terms but also as a percentage of total trade (50% over 2010, 25.4% of total trade). The outlook for LNG is strong and its global demand prospects further

  4. Distal clavicular osteolysis in adults: association with bench pressing intensity

    Energy Technology Data Exchange (ETDEWEB)

    Nevalainen, Mika T.; Morrison, William B.; Zoga, Adam C.; Roedl, Johannes B. [Sidney Kimmel Medical College at Thomas Jefferson University, Division of Musculoskeletal Imaging and Interventions, Department of Radiology, Thomas Jefferson University Hospital, Philadelphia, PA (United States); Ciccotti, Michael G. [Sidney Kimmel Medical College at Thomas Jefferson University, Division of Sports Medicine, Department of Orthopedic Surgery, Thomas Jefferson University Hospital, Rothman Institute, Philadelphia, PA (United States)

    2016-11-15

    To investigate the association between distal clavicular osteolysis (DCO) and bench pressing intensity. From a retrospective review of MRI shoulder reports of individuals between 20 and 40 years of age, 262 male patients with DCO and 227 age-matched male patients without DCO were selected. All patients had completed a bench pressing questionnaire. The patients' bench pressing frequency (times per week), duration (years of bench pressing), bench pressing weight (maximum bench pressing weight with one repetition = 1RM) and the ratio of bench pressing weight to body weight were compared between both groups using Chi-square and Mann-Whitney tests. The results showed that 56 % (146/262) of patients with DCO were high-intensity bench pressers (1RM more than 1.5 times the body weight) compared to 6 % (14/227) in patients without DCO. High-intensity bench pressing was a risk factor for DCO (OR = 19; 95 %CI = 11-35; p < 0.001). Low-intensity bench pressing (1RM less than 1.5 times the body weight) was not a risk factor for DCO (OR = 0.6; 95 % CI = 0.4-0.8). High frequency (>1 x /week) and duration (>5 years) of bench pressing were risk factors. In bench pressers who suffered from DCO, the mean 1RM was 283 lbs (±SD 57) compared to 209 lbs (±SD 60) in bench pressers not affected by DCO (p < 0.001, Mann-Whitney). High-intensity, but not low-intensity bench pressing is a risk factor for DCO. (orig.)

  5. Hydrostatic pressing effect on some properties of Al2O3 and Sc2O3 base ceramics

    International Nuclear Information System (INIS)

    Artemova, K.K.; Rudenko, L.A.; Maslova, G.Ya.; Levkovich, N.A.; Orlova, L.A.

    1981-01-01

    Found is the effect of hydrostatic pressing pressure on some physico-mechanical properties of the ceramic on the Al 2 O 3 and Se 2 O 3 base. Mathematical models, describing dependences of the strength of materials made of Al 2 O 3 and Sc 2 O 3 on sintering conditions and on hydrostatic pressing pressure, are plotted. Production regimes on the Al 2 O 3 and Sc 2 O 3 base ceramics with improved properties are optimized [ru

  6. Press touch code: A finger press based screen size independent authentication scheme for smart devices

    Science.gov (United States)

    Ranak, M. S. A. Noman; Nor, Nur Nadiah Hanim Binti Mohd; Zamli, Kamal Z.

    2017-01-01

    Due to recent advancements and appealing applications, the purchase rate of smart devices is increasing at a higher rate. Parallely, the security related threats and attacks are also increasing at a greater ratio on these devices. As a result, a considerable number of attacks have been noted in the recent past. To resist these attacks, many password-based authentication schemes are proposed. However, most of these schemes are not screen size independent; whereas, smart devices come in different sizes. Specifically, they are not suitable for miniature smart devices due to the small screen size and/or lack of full sized keyboards. In this paper, we propose a new screen size independent password-based authentication scheme, which also offers an affordable defense against shoulder surfing, brute force, and smudge attacks. In the proposed scheme, the Press Touch (PT)—a.k.a., Force Touch in Apple’s MacBook, Apple Watch, ZTE’s Axon 7 phone; 3D Touch in iPhone 6 and 7; and so on—is transformed into a new type of code, named Press Touch Code (PTC). We design and implement three variants of it, namely mono-PTC, multi-PTC, and multi-PTC with Grid, on the Android Operating System. An in-lab experiment and a comprehensive survey have been conducted on 105 participants to demonstrate the effectiveness of the proposed scheme. PMID:29084262

  7. Press touch code: A finger press based screen size independent authentication scheme for smart devices.

    Science.gov (United States)

    Ranak, M S A Noman; Azad, Saiful; Nor, Nur Nadiah Hanim Binti Mohd; Zamli, Kamal Z

    2017-01-01

    Due to recent advancements and appealing applications, the purchase rate of smart devices is increasing at a higher rate. Parallely, the security related threats and attacks are also increasing at a greater ratio on these devices. As a result, a considerable number of attacks have been noted in the recent past. To resist these attacks, many password-based authentication schemes are proposed. However, most of these schemes are not screen size independent; whereas, smart devices come in different sizes. Specifically, they are not suitable for miniature smart devices due to the small screen size and/or lack of full sized keyboards. In this paper, we propose a new screen size independent password-based authentication scheme, which also offers an affordable defense against shoulder surfing, brute force, and smudge attacks. In the proposed scheme, the Press Touch (PT)-a.k.a., Force Touch in Apple's MacBook, Apple Watch, ZTE's Axon 7 phone; 3D Touch in iPhone 6 and 7; and so on-is transformed into a new type of code, named Press Touch Code (PTC). We design and implement three variants of it, namely mono-PTC, multi-PTC, and multi-PTC with Grid, on the Android Operating System. An in-lab experiment and a comprehensive survey have been conducted on 105 participants to demonstrate the effectiveness of the proposed scheme.

  8. Densification of boron carbide at relatively low temperatures by hot pressing and hot isostatic pressing

    International Nuclear Information System (INIS)

    Telle, R.

    1988-01-01

    The poor sinterability of B 4 C limits its widespread application because both high temperatures and high pressures are required for a complete densification. Moreover, B 4 C suffers from a low strength and fracture toughness, possesses, however, a high potential because of its extreme hardness. Reaction hot pressing of B 4 C-WC-TiC-Si-Co mixtures resulting in B 4 C-TiB 2 -W 2 B 5 composites of high density exhibit remarkable mechanical properties. The influence of hot isostatic pressing (HIP) on the microstructure and the mechanical properties is investigated in cooperation with participants of the COST 503 activities and related to the strengthening and toughening mechanisms. Difficulties during densification by HIP arise from the evaporation of adsorbed volatiles as well as from the strong swelling of the powder compact due to the sintering reaction. Several HIP cycle designs were tested in order to prevent the bloating of the capsule and to control internal stresses due to the misfit of the thermal expansion of the entire phases. In comparison to single phase B 4 C ceramics, bending strength was improved to 1030 MPa, K Ic to 5.2 MPa/m, while hardness was comparable with HV1=38 GPa. Wear test were performed and related to the toughening mechanisms. (orig.) With 56 refs., 9 tabs., 64 figs

  9. Press touch code: A finger press based screen size independent authentication scheme for smart devices.

    Directory of Open Access Journals (Sweden)

    M S A Noman Ranak

    Full Text Available Due to recent advancements and appealing applications, the purchase rate of smart devices is increasing at a higher rate. Parallely, the security related threats and attacks are also increasing at a greater ratio on these devices. As a result, a considerable number of attacks have been noted in the recent past. To resist these attacks, many password-based authentication schemes are proposed. However, most of these schemes are not screen size independent; whereas, smart devices come in different sizes. Specifically, they are not suitable for miniature smart devices due to the small screen size and/or lack of full sized keyboards. In this paper, we propose a new screen size independent password-based authentication scheme, which also offers an affordable defense against shoulder surfing, brute force, and smudge attacks. In the proposed scheme, the Press Touch (PT-a.k.a., Force Touch in Apple's MacBook, Apple Watch, ZTE's Axon 7 phone; 3D Touch in iPhone 6 and 7; and so on-is transformed into a new type of code, named Press Touch Code (PTC. We design and implement three variants of it, namely mono-PTC, multi-PTC, and multi-PTC with Grid, on the Android Operating System. An in-lab experiment and a comprehensive survey have been conducted on 105 participants to demonstrate the effectiveness of the proposed scheme.

  10. Atlas of hot isostatic beryllium powder pressing diagrams

    International Nuclear Information System (INIS)

    Stoev, P.I.; Papirov, I.I.; Tikhinskij, G.F.; Vasil'ev, A.A.

    1995-01-01

    Diagrams of hot isotopic pressing (HIP) of beryllium powder with different grain size in a wide range of pressing parameters are built by mathematical modeling methods. The HIP diagrams presented are divided into 3 groups: parametric dependencies D=f(P,T); technological HIP diagrams; compacting mechanisms. The created data bank permits to optimise beryllium powder HIP with changing parameters. 4 refs., 23 figs

  11. Simulation Model of Automated Peat Briquetting Press Drive

    Directory of Open Access Journals (Sweden)

    A. A. Marozka

    2012-01-01

    Full Text Available The paper presents the developed fully functional simulation model of an automated peat briquetting press drive. The given model makes it possible to reduce financial and time costs while developing, designing and operating a double-stamp peat briquetting press drive.

  12. Criticism of the Press: Its Social, Psychological and Political Origins.

    Science.gov (United States)

    Becker, Lee B.; And Others

    This study examines data from several national polls about press coverage during the Watergate scandal, in order to assess the origins of press criticism. The polls were conducted between 28 September and 6 October 1973, during June 1974, and in August 1974. The data suggest that political variables--particularly support of Nixon, party…

  13. Design, manufacture and performance research of double acting hydraulic press

    OpenAIRE

    Koc, Erdem; Unver, Ertu; Ozturk, Hidayet

    1990-01-01

    This research presents the design and production of a double acting 40 tons capacity hydraulic press. The issues in the design, engineering manufacturing of the hydraulic press are reported specifically on both cylinders generating the same pressure and velocity using a solenoid directional control valve and a flow separating valve. (In Turkish)

  14. New Realities for Scholarly Presses in Trying Economic Times

    Science.gov (United States)

    Blakesley, David

    2014-01-01

    The author explains that Parlor Press is an independent publisher and distributor of scholarly and trade books in print and digital formats. It was founded in 2002 to address the need for an alternative scholarly, academic press attentive to emergent ideas and forms while maintaining the highest possible standards of quality, credibility, and…

  15. News from the Library: PressDisplay on mobile devices!

    CERN Multimedia

    CERN Library

    2013-01-01

    You are probably already using PressDisplay to read newspapers online, but for those of you who are not yet aware of this service, PressDisplay is an online portal where you can browse and read online articles from more than 1,900 newspapers from 95 countries, as soon as they are published.   Whether you are an experienced user or a beginner, we have good news concerning PressDisplay: our license now permits you to download complete newspaper issues to your mobile devices and read them offline wherever you like. To do that, you have to use the mobile app PressReader. Instructions on how to install the PressReader app are available here: For Ipad For Android smartphone For Android tablet For Windows 8 devices For BlackBerry Playbook For Android eReader Your feedback is welcome! Please contact us by e-mail.

  16. Predictor of regulation of uranium dioxide powder pressing process

    International Nuclear Information System (INIS)

    Motta, Eduardo Souza; Araujo, Victor Hugo Leal de; Bernardelli, Sergio Henrique

    2007-01-01

    One of the most important steps of the uranium dioxide pellets fabrication used in the nuclear fuel elements is the green pellets pressing. The target density of the pellets after the sintering process determines the density of the green pellet. To meet the same sintered target density the green density may vary according to the powder characteristics. These variations implies in changing the regulation of the press for different powder's patches. The regulation done empirically imply in productivity loss and necessity of reprocessing the pellets pressed during the press regulation and also depends on the operator experience. At this work, was developed an artificial neural network feed forward back propagation to predict the press regulation, depending on the powder characteristics and the green pellet's target density. The results obtained at INB - Industrias Nucleares do Brasil S. A. during the fabrication of the fifth recharge of Angra II nuclear power plant are presented. (author)

  17. Unknown loads affect force production capacity in early phases of bench press throws.

    Science.gov (United States)

    Hernández Davó, J L; Sabido Solana, R; Sarabia Marínm, J M; Sánchez Martos, Á; Moya Ramón, M

    2015-10-01

    Explosive strength training aims to improve force generation in early phases of movement due to its importance in sport performance. The present study examined the influence of lack of knowledge about the load lifted in explosive parameters during bench press throws. Thirteen healthy young men (22.8±2.0 years) participated in the study. Participants performed bench press throws with three different loads (30, 50 and 70% of 1 repetition maximum) in two different conditions (known and unknown loads). In unknown condition, loads were changed within sets in each repetition and participants did not know the load, whereas in known condition the load did not change within sets and participants had knowledge about the load lifted. Results of repeated-measures ANOVA revealed that unknown conditions involves higher power in the first 30, 50, 100 and 150 ms with the three loads, higher values of ratio of force development in those first instants, and differences in time to reach maximal rate of force development with 50 and 70% of 1 repetition maximum. This study showed that unknown conditions elicit higher values of explosive parameters in early phases of bench press throws, thereby this kind of methodology could be considered in explosive strength training.

  18. Simulation of press-forming for automobile part using ultra high tension steel

    Directory of Open Access Journals (Sweden)

    Tanabe I.

    2012-08-01

    Full Text Available In recent years, ultra high tension steel has gradually been used in the automobile industry. The development of press-forming technology is now essential by reason of its high productivity and high product quality. In this study, tensile tests were performed with a view to understanding the material properties. Press-forming tests were then carried out with regard to the behaviors of spring back and deep-drawability, and manufacturing a real product. The ultra high tension steel used in the experiments had a thickness of 1 mm and a tensile strength of 1000 MPa. Finally, simulations of spring back, deep-drawability and manufacturing a real product in ultra high tension steel were conducted and evaluated in order to calculate the optimum-press-forming conditions and the optimum shape of the die. FEM with non-linear and dynamic analysis using Euler-Lagrange’s element was used for the simulations. It is concluded from the results that (1 the simulations conformed to the results of the experiments (2 the simulations proved very effective for calculating the optimum press conditions and die shape.

  19. Preliminary investigation into the pressing process of sweet pearl millet and sweet sorghum biomass for ethanol production

    Energy Technology Data Exchange (ETDEWEB)

    Crepeau, M.; Khelifi, M.; Vanasse, A. [Laval Univ., Quebec City, PQ (Canada). Dept. of Soil Science and Agri-Food Engineering

    2010-07-01

    Corn is the main source for biofuel production in North America. However, both sweet pearl millet and sweet sorghum crops represent an interesting alternative to corn for ethanol production because of their high biomass yield under a wide range of environmental conditions and high concentration of readily fermentable sugars. Coproducts such as pressing residues can be also be utilized so that nothing is lost in the process. However, in order to improve the extraction of juice for ethanol production, the pressing process of this biomass must be optimized. Preliminary experiments were therefore conducted to optimize the juice extraction from sweet pearl millet and sweet sorghum using 2 different presses, notably a screw press and a manually operated hydraulic press. Both types of biomass were either chopped finely or coarsely and were exposed to various pressures with the hydraulic press. The volume of juice extracted from both crops increased linearly with increasing pressure. Sweet sorghum appeared to be a better feedstock for ethanol production because it produced about 0.03 to 0.06 litre of juice per kg of biomass more than sweet pearl millet. Juice extraction was more effective with the screw press, but only a small difference was noted between the 2 chopping modes.

  20. Nonlinear friction model for servo press simulation

    Science.gov (United States)

    Ma, Ninshu; Sugitomo, Nobuhiko; Kyuno, Takunori; Tamura, Shintaro; Naka, Tetsuo

    2013-12-01

    The friction coefficient was measured under an idealized condition for a pulse servo motion. The measured friction coefficient and its changing with both sliding distance and a pulse motion showed that the friction resistance can be reduced due to the re-lubrication during unloading process of the pulse servo motion. Based on the measured friction coefficient and its changes with sliding distance and re-lubrication of oil, a nonlinear friction model was developed. Using the newly developed the nonlinear friction model, a deep draw simulation was performed and the formability was evaluated. The results were compared with experimental ones and the effectiveness was verified.

  1. How to press-release and take care of expression in articles at press side

    International Nuclear Information System (INIS)

    Hamamoto, Kazuko; Narabayashi, Tadashi; Kobayashi, Masahide; Akizuki, Teruo; Onishi, Hidetoshi

    2008-01-01

    As for the influences of Chuetsu-Oki Earthquake on Kashiwazaki-Kariwa Nuclear Power Station, we can conclude that 'the safety function of the nuclear power station, that is, 'Shutdown', 'Cooling down' and 'Isolating' functioned as per designed even against earthquake beyond assumption, and fundamental nuclear safety could be assured'. Nevertheless, it is said that one of the causes that harmful rumor had spread was due to mass communication media. In the press reports on some nuclear power station when affected by an earthquake and on trouble in the nuclear power station in the future, we will propose that the publication should be really useful for habitants and citizens and be promoted in the positive and expected direction, in order not to make the same mistake as this time. JSME should aim at implement the above-mentioned proposal under cooperation with other academic societies and organizations. (author)

  2. Men exhibit greater fatigue resistance than women in alternated bench press and leg press exercises.

    Science.gov (United States)

    Monteiro, Estêvão R; Steele, James; Novaes, Jefferson S; Brown, Amanda F; Cavanaugh, Mark T; Vingren, Jakob L; Behm, David G

    2017-11-17

    The purpose of this study was to evaluate the influence of sex, exercise order, and rest interval on neuromuscular fatigue resistance for an alternated strength training sequence of bench press (BP) and leg press (LP) exercises. Twelve women and 16 men, both recreationally trained, performed four sessions in a random order: 1) BP followed by LP with three-minutes rest (BP+LP with rest), 2) LP followed by BP with three-minutes rest (LP+BP with rest), 3) BP followed by LP without rest interval (BP+LP no rest), and 4) LP followed by BP without rest interval (LP+BP no rest). Participants performed four sets with 100% of 10RM load to concentric failure with the goal of completing the maximum number of repetitions in both exercises. The fatigue index was analyzed from the first and last sets of each exercise bout. A main effect for sex showed that women exhibited 25.5% (p=0.001) and 24.5% (p=0.001) greater BP and LP fatigue than men respectively when performing 10RM. Men exhibited greater BP (p<0.0001; 34.1%) and LP (p<0.0001; 30.5%) fatigue resistance when a rest period was provided. Men did not show an exercise order effect for BP fatigue and exhibited greater (p=0.0003; 14.5%) LP fatigue resistance when BP was performed first. The present study demonstrated the greater fatigue resistance of men when performing 10RM BP and LP exercises. Since men tend to experience less fatigue with the second exercise in the exercise pairing, women's training programs should be adjusted to ensure they do not parallel men's resistance training programs.

  3. A superconducting solenoid and press for permanent magnet fabrication

    International Nuclear Information System (INIS)

    Mulcahy, T. M.; Hull, J. R.

    2002-01-01

    For the first time, a superconducting solenoid (SCM) was used to increase the remnant magnetization of sintered NdFeB permanent magnets (PMs). In particular, improved magnetic alignment of commercial-grade PM powder was achieved, as it was axial die pressed into 12.7-mm diameter cylindrical compacts in the 76.2-mm warm bore of a 9-T SCM. The press used to compact the powder is unique and was specifically designed for use with the SCM. Although the press was operated in the batch mode for this proof of concept study, its design is intended to enable automated production. In operation, a simple die and punch set made of nonmagnetic materials was filled with powder and loaded into a nonmagnetic press tube. The cantilevered press tube was inserted horizontally, on a carrier manually advanced along a track, into the SCM. The robustness of the mechanical components and the SCM, in its liquid helium dewar, were specifically designed to allow for insertion and extraction of the magnetic powder and compacts, while operating at 9 T. Compaction was achieved by pressing the punches between the closed end of the press tube and the hydraulic cylinder mounted on the opposite end. Improvements up to 10% in magnetization and 20% in energy products of the permanent magnets were obtained, as the alignment fields were increased above the 2-T maximum field of the electromagnets used in industry. Increases in magnetization of 3% are significant in the mature sintered magnet industry

  4. Jatropha press cake as organic fertilizer in lettuce cultivation

    Directory of Open Access Journals (Sweden)

    José R. Mantovani

    Full Text Available ABSTRACT In biodiesel production, vegetable press cake is obtained as waste, and a suitable destination for jatropha press cake would be the use in agriculture as organic fertilizer. This study aimed to evaluate the effect of jatropha press cake on soil fertility attributes and on lettuce production and accumulation of nutrients in the shoots. The experiment was conducted in pots in a greenhouse, in a randomized block design with eight treatments and five replicates. The treatments consisted of doses of jatropha press cake equivalent to 0, 0.5, 1.0, 2.0, 4.0, 8.0, 16.0 and 32.0 t ha-1. Portions of 5.5 dm3 of soil received limestone, phosphate fertilizer and the doses of jatropha press cake, and remained incubated for 30 days. After incubation, soil samples were collected, each pot received one lettuce seedling and the experiment was carried out for 45 days. The organic fertilization with jatropha press cake increased the contents of nutrients in the soil, especially K+, but caused increment in soil acidity and electrical conductivity. The use of jatropha press cake as organic fertilizer decreased lettuce production and accumulation of nutrients in the shoots.

  5. Implementing Strategies for Drying and Pressing Wood Without Emissions Controls

    Energy Technology Data Exchange (ETDEWEB)

    Sujit Banerjee; Terrance Conners

    2007-09-07

    Drying and pressing wood for the manufacture of lumber, particleboard, oriented strand board (OSB), veneer and medium density fiberboard (MDF) release volatile organic compounds (VOCs) into the atmosphere. These emissions require control equipment that are capital-intensive and consume significant quantities of natural gas and electricity. The objective of our work was to understand the mechanisms through which volatile organic compounds are generated and released and to develop simple control strategies. Of the several strategies developed, two have been implemented for OSB manufacture over the course of this study. First, it was found that increasing final wood moisture by about 2-4 percentage points reduced the dryer emissions of hazardous air pollutants by over 70%. As wood dries, the escaping water evaporatively cools the wood. This cooling tapers off wood when the wood is nearly dry and the wood temperature rises. Thermal breakdown of the wood tissue occurs and VOCs are released. Raising the final wood moisture by only a few percentage points minimizes the temperature rise and reduces emissions. Evaporative cooling also impacts has implications for VOC release from wood fines. Flaking wood for OSB manufacture inevitable generates fines. Fines dry out rapidly because of their high surface area and evaporative cooling is lost more rapidly than for flakes. As a result, fines emit a disproportionate quantity of VOCs. Fines can be reduced in two ways: through screening of the green furnish and through reducing their generation during flaking. The second approach is preferable because it also increased wood yield. A procedure to do this by matching the sharpness angle of the flaker knife to the ambient temperature was also developed. Other findings of practical interests are as follows: Dielectric heating of wood under low-headspace conditions removes terpenes and other extractives from softwood; The monoterpene content in trees depend upon temperature and seasonal

  6. The effect of sodium bicarbonate ingestion on back squat and bench press exercise to failure.

    Science.gov (United States)

    Duncan, Michael J; Weldon, Anthony; Price, Michael J

    2014-05-01

    This study examined the acute effects of NaHCO3 ingestion on repetitions to failure and rating of perceived exertion in the back squat and bench press in trained men. Eight resistance-trained men took part in this double-blind, randomized crossover experimental study whereby they ingested NaHCO3 (0.3 g·kg(-1) body mass) or placebo (sodium chloride NaCl: 0.045 g·kg(-1) body mass) solution 60 minutes before completing a bout of resistance exercise (3 sets of bench press and back squat exercise to failure at an intensity of 80% 1 repetition maximum). Experimental conditions were separated by at least 48 hours. Participants completed more repetitions to failure in the back squat after NaHCO3 ingestion (p = 0.04) but not for bench press (p = 0.679). Mean ± SD of total repetitions was 31.3 ± 15.3 and 24.6 ± 16.2 for back squat and 28.7 ± 12.2 and 26.7 ± 10.2 for bench press in NaHCO3 and placebo conditions, respectively. Repetitions to failure decreased as set increased for the back squat and bench press (p = 0.001, both). Rating of perceived exertion significantly increased with set for the back squat and bench press (p = 0.002, both). There was no significant change in blood lactate across time or between conditions. There were however treatment × time interactions for blood pH (p = 0.014) and blood HCO3 concentration (p = 0.001). After ingestion, blood pH and HCO3 (p = 0.008) concentrations were greater for the NaHCO3 condition compared with the placebo condition (p < 0.001). The results of this study suggest that sodium bicarbonate ingestion can enhance resistance exercise performance using a repetition to failure protocol in the first exercise in a resistance exercise session.

  7. Improvement of Sol-Gel Derived PbZrxTi1-xO3 Film Properties Using Thermal Press Treatment

    Science.gov (United States)

    Kaneda, Toshihiko; Kim, Joo-Nam; Tokumitsu, Eisuke; Shimoda, Tatsuya

    2010-09-01

    A thermal press treatment was introduced in the sol-gel process of PbZrxTi1-xO3 (PZT) thin films for the first time and the crystalline and electrical characteristics of the PZT films were investigated. The thermal press treatment was applied to the amorphous PZT gel film before crystallization annealing. It is found that the crystalline orientation and grain size of the PZT film fabricated with the thermal press treatment are different from those of the film fabricated by the conventional sol-gel process without the thermal press treatment, even though the crystallization conditions are exactly the same. It is demonstrated that the electrical properties, especially leakage current density and breakdown field, are significantly improved for the PZT film fabricated with the thermal press treatment. Furthermore, we also demonstrate that the fatigue property is improved by introducing the thermal press treatment.

  8. Mannes of Forging and Perspectives of Knuckle Joint Presses Modernization

    Directory of Open Access Journals (Sweden)

    A. A. Antsifirov

    2014-01-01

    Full Text Available The article raises an issue to enhance technological forging capabilities on the known knuckle joint presses. It provides an illustrated overview of main design types of presses with crank-knuckle, toggle-knuckle, and knuckle joint mechanisms. The article also shows the advantages of the modernization way and improvement just of the active press equipment in terms of quality-to-price ratio, for example, as compared to the similar new foreign press equipment.It gives an overview of features, which provide forging processes owing to kinetic energy accumulated with the moving parts of the known designs of the knuckle joint presses depending on the drive actuating mechanism. Focused attention is drawn to forging on the knuckle joint presses for a time of contact with a work piece to be comparable with the duration of the work piece deformation process on hydraulic forging hammers. This allows us to forge thin-wall products with process automation compared to the forging hammers.Analysis of accumulating processes of kinetic energy by the moving parts of the knuckle joint presses has shown that presses driven by hydraulic cylinders or two screw hydraulic cylinder are the most optimal for technological operations as evidenced by references to domestic and foreign invention certificates and patents. The article presents disadvantages of forging on presses with hydraulic or pneumatic drive. It is a dependence of the deformation force, caused, mainly, by a force of the drive cylinder. The article gives linear movement rate quantities of press moving members depending on the drives of the actuating mechanism. Based on the above analysis of the features to manufacture work pieces on the knuckle joint presses, the article gives the rationale for the relevance of forging in a short period of time, provided that the moving parts of the press accumulate the required kinetic energy. This can be achieved only through modernization and improvement of forging

  9. Press problem related to nuclear energy news reporting

    International Nuclear Information System (INIS)

    Arai, Mitsuo

    2008-01-01

    Since the event of Niigataken Chuetsu-oki Earthquake in 2007 and the subsequent press reports on damage of nuclear power station after it, a stance of media is being questioned. In order to clear this problem, basic organizational structure of the press related to nuclear energy news was analyzed. Local news department, social news department, science news department and economical news department involve in nuclear energy news the accordance with their own situations and concerns. This structure makes problem of nuclear energy news reporting complicated. Changing this system is required but very difficult. It is concluded that the press problem around nuclear energy news is strange. (author)

  10. Neuromuscular Control During the Bench Press Movement in an Elite Disabled and Able-Bodied Athlete

    Directory of Open Access Journals (Sweden)

    Gołaś Artur

    2017-12-01

    Full Text Available The disabled population varies significantly in regard to physical fitness, what is conditioned by the damage to the locomotor system. Recently there has been an increased emphasis on the role of competitive sport in enhancing health and the quality of life of individuals with disability. One of the sport disciplines of Paralympics is the flat bench press. The bench press is one of the most popular resistance exercises used for the upper body in healthy individuals. It is used not only by powerlifters, but also by athletes in most strength-speed oriented sport disciplines. The objective of the study was to compare neuromuscular control for various external loads (from 60 to 100% 1RM during the flat bench press performed by an elite able-bodied athlete and an athlete with lower limb disability. The research project is a case study of two elite bench press athletes with similar sport results: an able-bodied athlete (M.W., age 34 years, body mass 103 kg, body height 1.72 m, 1RM in the flat bench press 200 kg and a disabled athlete (M.T., age 31 years, body mass 92 kg, body height 1.70 m, 1RM in the flat bench press 190 kg. The activity was recorded for four muscles: pectoralis major (PM, anterior deltoid (AD, as well as for the lateral and long heads of the triceps brachii (TBlat and TBlong. The T-test revealed statistically significant differences between peak activity of all the considered muscles (AD with p = 0.001; PM with p = 0.001; TBlat with p = 0.0021 and TBlong with p = 0.002 between the 2 athletes. The analysis of peak activity differences of M.W and M.T. in relation to the load revealed statistically significant differences for load changes between: 60 to 100% 1RM (p = 0.007, 70 to 100% 1RM (p = 0.016 and 80 to 100% 1RM (p = 0.032. The flat bench press performed without legs resting firmly on the ground leads to the increased engagement of upper body muscles and to their greater activation. Isolated initial positions can be used to

  11. Neuromuscular Control During the Bench Press Movement in an Elite Disabled and Able-Bodied Athlete.

    Science.gov (United States)

    Gołaś, Artur; Zwierzchowska, Anna; Maszczyk, Adam; Wilk, Michał; Stastny, Petr; Zając, Adam

    2017-12-01

    The disabled population varies significantly in regard to physical fitness, what is conditioned by the damage to the locomotor system. Recently there has been an increased emphasis on the role of competitive sport in enhancing health and the quality of life of individuals with disability. One of the sport disciplines of Paralympics is the flat bench press. The bench press is one of the most popular resistance exercises used for the upper body in healthy individuals. It is used not only by powerlifters, but also by athletes in most strength-speed oriented sport disciplines. The objective of the study was to compare neuromuscular control for various external loads (from 60 to 100% 1RM) during the flat bench press performed by an elite able-bodied athlete and an athlete with lower limb disability. The research project is a case study of two elite bench press athletes with similar sport results: an able-bodied athlete (M.W., age 34 years, body mass 103 kg, body height 1.72 m, 1RM in the flat bench press 200 kg) and a disabled athlete (M.T., age 31 years, body mass 92 kg, body height 1.70 m, 1RM in the flat bench press 190 kg). The activity was recorded for four muscles: pectoralis major (PM), anterior deltoid (AD), as well as for the lateral and long heads of the triceps brachii (TBlat and TBlong). The T-test revealed statistically significant differences between peak activity of all the considered muscles (AD with p = 0.001; PM with p = 0.001; TBlat with p = 0.0021 and TBlong with p = 0.002) between the 2 athletes. The analysis of peak activity differences of M.W and M.T. in relation to the load revealed statistically significant differences for load changes between: 60 to 100% 1RM (p = 0.007), 70 to 100% 1RM (p = 0.016) and 80 to 100% 1RM (p = 0.032). The flat bench press performed without legs resting firmly on the ground leads to the increased engagement of upper body muscles and to their greater activation. Isolated initial positions can be used to generate

  12. The influence of isometric preload on power expressed during bench press in strength-trained men.

    Science.gov (United States)

    Bartolomei, Sandro; Fukuda, David H; Hoffman, Jay R; Stout, Jeffrey R; Merni, Franco

    2017-03-01

    The purpose of this study was to compare the power expressed during the bench press exercise in resistance-trained men following different pre-activation conditions. Twenty-two trained men (age 24.1 ± 1.7 years, height 178.6 ± 6.1 cm, body mass 81.1 ± 10.6 kg) completed a maximal effort bench press (1-RM) test (100.0 kg ± 8.1 kg). In a subsequent assessment, each participant performed concentric bench press movements with loads of 20%, 30%, 40% and 50% of their 1-RM preceded by either a concentric contraction (CC), a low isometric preload (LIP; 70% 1-RM) or a high isometric preload (HIP; 100% 1-RM) conditions. All movements were performed in a Smith machine with a settable quick-release device. Participants performed all three conditions in randomized fashion. Results indicated that power outputs during the bench press exercise following HIP were significantly (p < 0.05) greater than CC at 20% 1-RM (+9%), 30% 1-RM (+16%) and 40% 1-RM (+14%), and LIP at 20% 1-RM (+4%), 30% 1-RM (+20%) and 40% 1-RM (+15%). No differences were found between conditions at 50% 1-RM. Area under the force-power curve with HIP was greater (p < 0.05) than with CC and LIP. In conclusion, results of this study indicate that the use of a HIP (100% 1-RM) in trained participants results in significantly greater power output during the concentric phase of a multi-joint exercise when compared to standard concentric movement.

  13. Concept Design of Movable Beam of Hydraulic Press

    Directory of Open Access Journals (Sweden)

    Li Yancong

    2017-01-01

    Full Text Available The hydraulic press movable beam is one of the key components of the hydraulic press; its design quality impacts the accuracy of the workpiece that the press suppressed. In this paper, first, with maximum deflection and material strength as constraints, mechanical model of the movable beam is established; next, the concept design model of the moveable beam structure is established; the relationship among the force of the side cylinder, the thickness of the inclined plate, outer plate is established also. Taking movable beam of the 100MN type THP10-10000 isothermal forging hydraulic press as an example, the conceptual design result is given. This concept design method mentoned in the paper has general meaning and can apply to other similar product design.

  14. Fabrication and properties of hot pressed bismuth tungstate

    International Nuclear Information System (INIS)

    Streicher, W.L.

    1978-01-01

    Bi 2 WO 6 is a synthetic polar material that is a possible candidate for energy conversion and detection systems. Previous research on this material has been concerned with crystal growth and sintering characteristics of polycrystalline compacts. This study involves itself with the fabrication of polycrystalline compacts by hot pressing techniques. Densities approaching theoretical crystal density were achieved by hot pressing at 850 0 C for one hour with pressures exceeding 35 MPa. Before hot pressing, the sintering range was determined by high temperature dilatometry of unfired Bi 2 WO 6 ceramics. Hot pressed discs were characterized by scanning electron microscopy, differential scanning calorimetry, and x-ray diffraction. Electrical properties were determined by dc resistivity, capacitance, and conductance measurements, ac poling, dc poling, and current-voltage measurements

  15. Pleurotus pulmonarius cultivation on amended palm press fibre waste

    African Journals Online (AJOL)

    Bola

    2015-05-13

    May 13, 2015 ... Seven different substrates (A to G) were prepared from saw dust, palm press ... can grow in a wide range of soil types with relatively low ..... documented to include; cotton waste, sugar cane ..... Canada wood ash sources. Can.

  16. Poland's Press and Broadcasting Under the Gierek Regime

    Science.gov (United States)

    Shanor, Donald R.

    1974-01-01

    Reports that the Polish press and broadcasting have been carrying more news and less propaganda since the 1970 Baltic upheavel and that the Polish media are generally allowed more freedom than media in other Communist nations. (RB)

  17. Cars & Censorship: How Advertising Pressure Can Corrupt a Free Press.

    Science.gov (United States)

    Collins, Ronald K. L.

    1992-01-01

    Discusses "private censorship" as it relates to car dealers and television advertising. Defines "private censorship" as that which occurs when a broadcaster suppresses or alters a news story that affects commercial clients (advertisers). Makes recommendations for a freer press. (JOW)

  18. Microstructural and Mechanical Study of Press Hardening of Thick Boron Steel Sheet

    Science.gov (United States)

    Pujante, J.; Garcia-Llamas, E.; Golling, S.; Casellas, D.

    2017-09-01

    Press hardening has become a staple in the production of automotive safety components, due to the combination of high mechanical properties and form complexity it offers. However, the use of press hardened components has not spread to the truck industry despite the advantages it confers, namely affordable weight reduction without the use of exotic materials, would be extremely attractive for this sector. The main reason for this is that application of press hardened components in trucks implies adapting the process to the manufacture of thick sheet metal. This introduces an additional layer of complexity, mainly due to the thermal gradients inside the material resulting in though-thickness differences in austenitization and cooling, potentially resulting in complex microstructure and gradient of mechanical properties. This work presents a preliminary study on the press hardening of thick boron steel sheet. First of all, the evolution of the sheet metal during austenitization is studied by means of dilatometry tests and by analysing the effect of furnace dwell time on grain size. Afterwards, material cooled using different cooling strategies, and therefore different effective cooling rates, is studied in terms of microstructure and mechanical properties. Initial results from finite element simulation are compared to experimental results, focusing on the phase composition in through thickness direction. Results show that industrial-equivalent cooling conditions do not lead to gradient microstructures, even in extreme scenarios involving asymmetrical cooling.

  19. Solidification of glass powder by a hydrothermal hot-pressing technique

    International Nuclear Information System (INIS)

    Nishioka, Mamoru; Yanagisawa, Kazumichi; Yamasaki, Nakamichi

    1986-01-01

    A borosilicate glass powder was solidified with a NaOH solution or distilled water by the hydrothermal hot-pressing technique. The effect of hydrothermal conditions on the compressive strength was investigated, and the densification mechanism of the glass powder during the hydrothermal hot-pressing was discussed in terms of isothermal shrinkage. The glass powder was successfully solidified by hydrothermal hot-pressing at a reaction temperature lower than that of an ordinary pressure sintering. The solidified body obtained in the presence of distilled water (10 wt%) at 280 deg C had a high compressive strength of about 2300 kg/cm 2 . The analysis of initial densification process of the glass powder in hydrothermal hot-pressing with Murray's rate equation revealed that the densification proceeds both by viscous flow and by rearrangement process. Analysis of the shrinkage rates with a rate equation of hydrothermal reaction suggested that the dissolution of particles into solution controlled the initial densification of the glass powder, and that the alkaline metal acted as a catalyst. (author)

  20. Inter-Investigator Reliability of Anthropometric Prediction of 1RM Bench Press in College Football Players.

    Science.gov (United States)

    Schumacher, Richard M; Arabas, Jana L; Mayhew, Jerry L; Brechue, William F

    2016-01-01

    The purpose of this study was to determine the effect of inter-investigator differences in anthropometric assessments on the prediction of one-repetition maximum (1RM) bench press in college football players. Division-II players (n = 34, age = 20.4 ± 1.2 y, 182.3 ± 6.6 cm, 99.1 ± 18.4 kg) were measured for selected anthropometric variables and 1RM bench press at the conclusion of a heavy resistance training program. Triceps, subscapular, and abdominal skinfolds were measured in triplicate by three investigators and used to estimate %fat. Arm circumference was measured around a flexed biceps muscle and was corrected for triceps skinfold to estimate muscle cross-sectional area (CSA). Chest circumference was measured at mid-expiration. Significant differences among the testers were evident in six of the nine anthropometric variables, with the least experienced tester being significantly different from the other testers on seven variables, although average differences among investigators ranged from 1-2% for circumferences to 4-9% for skinfolds. The two more experienced testers were significantly different on only one variable. Overall agreement among testers was high (ICC>0.895) for each variable, with low coefficients of variation (CVbench press using a non-performance anthropometric equation. Minimal experience in anthropometry may not impede strength and conditioning specialists from accurately estimating 1RM bench press.

  1. Postactivation potentiation: effect of various recovery intervals on bench press power performance.

    Science.gov (United States)

    Ferreira, Sandra Lívia de Assis; Panissa, Valéria Leme Gonçalves; Miarka, Bianca; Franchini, Emerson

    2012-03-01

    Postactivation potentiation (PAP) is a strategy used to improve performance in power activities. The aim of this study was to determine if power during bench press exercise was increased when preceded by 1 repetition maximum (1RM) in the same exercise and to determine which time interval could optimize PAP response. For this, 11 healthy male subjects (age, 25 ± 4 years; height, 178 ± 6 cm; body mass, 74 ± 8 kg; bench press 1RM, 76 ± 19 kg) underwent 6 sessions. Two control sessions were conducted to determine both bench press 1RM and power (6 repetitions at 50% 1RM). The 4 experimental sessions were composed of a 1RM exercise followed by power sets with different recovery intervals (1, 3, 5, and 7 minutes), performed on different days, and determined randomly. Power values were measured via Peak Power equipment (Cefise, Nova Odessa, São Paulo, Brazil). The conditions were compared using an analysis of variance with repeated measures, followed by a Tukey test. The significance level was set at p bench press and that such a strategy could be applied as an interesting alternative to enhance the performance in tasks aimed at increasing upper-body power performance.

  2. Bench Press Upper-Body Muscle Activation Between Stable and Unstable Loads.

    Science.gov (United States)

    Dunnick, Dustin D; Brown, Lee E; Coburn, Jared W; Lynn, Scott K; Barillas, Saldiam R

    2015-12-01

    The bench press is one of the most commonly used upper-body exercises in training and is performed with many different variations, including unstable loads (ULs). Although there is much research on use of an unstable surface, there is little to none on the use of an UL. The purpose of this study was to investigate muscle activation during the bench press while using a stable load (SL) vs. UL. Twenty resistance-trained men (age = 24.1 ± 2 years; ht = 177.5 ± 5.8 cm; mass = 88.7 ± 13.7 kg) completed 2 experimental conditions (SL and UL) at 2 different intensities (60 and 80% one repetition maximum). Unstable load was achieved by hanging 16 kg kettlebells by elastic bands from the end of the bar. All trial lifts were set to a 2-second cadence with a slight pause at the bottom. Subjects had electrodes attached to 5 muscles (pectoralis major, anterior deltoid, medial deltoid, triceps brachii, and latissimus dorsi) and performed 3 isometric bench press trials to normalize electromyographic data. All 5 muscles demonstrated significantly greater activation at 80% compared with 60% load and during concentric compared with eccentric actions. These results suggest that upper body muscle activation is not different in the bench press between UL and SL. Therefore, coaches should use their preference when designing training programs.

  3. A liberdade de imprensa em chave marxiana / Freedom of the press in a marxian perspective

    Directory of Open Access Journals (Sweden)

    Helio Lena Lena

    2011-12-01

    Full Text Available Resumo O presente artigo tem por objetivo discutir, mesmo que preliminarmente, a idéia de liberdade de imprensa em Karl Marx, Wladimir Lênin e Leon Trotsky. Acreditamos que, a práxis política destes atores sociais estava condicionada pela existência de uma liberdade de expressão como reflexo da organização política. Todavia, nem sempre o que se verificou na prática, foi a liberdade de imprensa dada pelos governantes aos opositores; para tanto, os atores supracitados acreditavam que a liberdade de imprensa constituía um direito alienável dos cidadãos. Palavras-chave: Liberdade de imprensa, jornalismo proletário, comunismo Abstract This article intends to argue, even though on preliminary basis, the idea of press freedom in the thought of Karl Marx, Wladimir Lenin and Leon Trotsky. We believe that the political praxis of these social actors was conditioned by the existence of free speech as a reflex of the political organization. On another hand, not always was press freedom actually given by governments to oppositionists; in order to achieve it, the previously mentioned actors believed that press freedom was an alienable right of citizens. Keywords: Freedom of the press, proletarian journalism, communism 

  4. Modelling of powder die compaction for press cycle optimization

    Directory of Open Access Journals (Sweden)

    Bayle Jean-Philippe

    2016-01-01

    Full Text Available A new electromechanical press for fuel pellet manufacturing was built last year in partnership between CEA-Marcoule and ChampalleAlcen. This press was developed to shape pellets in a hot cell via remote handling. It has been qualified to show its robustness and to optimize the compaction cycle, thus obtaining a better sintered pellet profile and limiting damage. We will show you how 400 annular pellets have been produced with good geometry's parameters, based on press settings management. These results are according to a good phenomenological pressing knowledge with Finite Element Modeling calculation. Therefore, during die pressing, a modification in the punch displacement sequence induces fluctuation in the axial distribution of frictional forces. The green pellet stress and density gradients are based on these frictional forces between powder and tool, and between grains in the powder, influencing the shape of the pellet after sintering. The pellet shape and diameter tolerances must be minimized to avoid the need for grinding operations. To find the best parameters for the press settings, which enable optimization, FEM calculations were used and different compaction models compared to give the best calculation/physical trial comparisons. These simulations were then used to predict the impact of different parameters when there is a change in the type of powder and the pellet size, or when the behavior of the press changes during the compaction time. In 2016, it is planned to set up the press in a glove box for UO2 manufacturing qualification based on our simulation methodology, before actual hot cell trials in the future.

  5. Dynamic Multiaxial Response of a Hot-Pressed Aluminum Nitride

    Science.gov (United States)

    2012-01-05

    Hutchinson, Adv. Appl . Mech. 29 (1992). [34] H. Ming-Yuan, J.W. Hutchinson, Int. J. Solids Struct. 25 (1989) 1053. [35] J. Salem , L. Ghosn, Int. J...Dynamic Multiaxial Response of a Hot- Pressed Aluminum Nitride by Guangli Hu, C. Q. Chen, K. T. Ramesh, and J. W. McCauley ARL-RP-0487...Laboratory Aberdeen Proving Ground, MD 21005-5066 ARL-RP-0487 June 2014 Dynamic Multiaxial Response of a Hot- Pressed Aluminum Nitride

  6. Speech freedom and press freedom in human security in Rwanda

    OpenAIRE

    Niyonzima, Oswald

    2014-01-01

    Treball Final de Màster Universitari Internacional en Estudis de Pau, Conflictes i Desenvolupament. Codi: SAA074. Curs: 2013/2014 Freedom of speech and press freedom are key foundations of all human rights as stipulated in human rights declaration of 1948. Denying people the right to free speech is keeping them away from what is happening in this world, thus, hindering them from participating in decision making. While speech freedom and press freedom are key tools to measure if a country ...

  7. PRESS: A Novel Framework of Trajectory Compression in Road Networks

    OpenAIRE

    Song, Renchu; Sun, Weiwei; Zheng, Baihua; Zheng, Yu

    2014-01-01

    Location data becomes more and more important. In this paper, we focus on the trajectory data, and propose a new framework, namely PRESS (Paralleled Road-Network-Based Trajectory Compression), to effectively compress trajectory data under road network constraints. Different from existing work, PRESS proposes a novel representation for trajectories to separate the spatial representation of a trajectory from the temporal representation, and proposes a Hybrid Spatial Compression (HSC) algorithm ...

  8. Corporate social responsibility's discourse in lithuanian business press

    OpenAIRE

    Marčenkovas, Marius

    2014-01-01

    The object of this master work is corporate social responsibility's (CSR) discourse. The purpose of this work is to analyze how Lithuanian business press presents CSR topic. The main tasks to reach this purpose are: overview and compare CSR definitions; analyze media impact to CSR; analyze and summarize CSR discourse in Lithuanian business press. Literature analysis, synthesis and comparative methods were used to drawn conclusions. After the literature analysis of such scientists as Ph. Kotle...

  9. Improving the Quality of Hot Stamping Parts with Innovative Press Technology and Inline Process Control

    Science.gov (United States)

    Vollmer, R.; Palm, C.

    2017-09-01

    The increasing number of hot stamped parts in the automotive industry is challenging different process areas. This paper presents a method how to improve the production rates over the whole life cycle of a hot forming part. In the core element of a hot forming line, the hydraulic press, mainly two processing steps are performed. Forming and quenching of the sheet metal part. In addition to the forming operation, it is inevitable to optimize the quenching condition in the bottom dead centre in order to reach a fully martensitic structure and tight geometrical tolerances of the part. Deviations in the blank thickness, tool wear, polishing of classical tools impair the quenching condition and therefore the part quality over the time. A new press and tool design has been developed to counter this effect by providing homogenous contact pressure over the whole die. Especially with a multi cavity tool, the new method is advantageous. Test series have shown that the new tool and press concept can produce parts with a blank thickness of 1.0 mm within 8.0 s cycle time. The so called PCH flex principle makes it possible to produce such high output rates under reliable conditions.

  10. Resident-performed Ex-PRESS shunt implantation versus trabeculectomy.

    Science.gov (United States)

    Seider, Michael I; Rofagha, Soraya; Lin, Shan C; Stamper, Robert L

    2012-09-01

    To compare outcomes between resident-performed trabeculectomy and Ex-PRESS shunt implantation. A consecutive cohort of 36 Ex-PRESS shunt implantations and 57 trabeculectomies (1 eye/patient) performed by resident surgeons in their third year of ophthalmic training at the University of California, San Francisco and at the San Francisco Veterans Administration Hospital, under the supervision of a single glaucoma fellowship-trained surgeon were included in this study. Eyes with PRESS shunt groups at all follow-up points. On average, the Ex-PRESS shunt group required significantly less ocular antihypertensive medication to control IOP at 3 months postoperative (P=0.01), but no difference was found at 6 months or 1 year (all, P≥0.28). A larger proportion of Ex-PRESS shunt patients had good IOP control without medication at 3 (P=0.057) and 6 months (P=0.076) postoperatively. No difference was found in the rates of sight-threatening complications between groups (all, P≥0.22). In the hands of ophthalmology residents in their third year of training, the trabeculectomy and Ex-PRESS shunt implantation procedures perform comparably in terms of postoperative IOP control, reduction in patient dependence on ocular antihypertensive medications, and risk of complication in our population.

  11. France Electricity Report for 2014 - Press kit

    International Nuclear Information System (INIS)

    Cisse, Carole; Marie, Stephen

    2015-01-01

    of photovoltaic power of nearly 5,300 MW. Generation capacity of the coal-fired power plants, several of which have been shut down, plummeted by 58%. With gas-fired plants being deployed less (-28%), and given the weather conditions not being conducive to the use of these means of generation, fossil fuel power generation fell by 17.7 TWh (-40%). The drop in consumption, combined with the boom in renewable energies and decreased fossil fuel power generation meant that greenhouse gas emissions were reduced by more than 40% in the electricity sector, with 19 million tonnes of CO 2 equivalent. Electricity trades were especially sustained in 2014 (92.4 TWh exported and 27.3 TWh imported). With a positive trade balance of 65.1 TWh in 2014, France remained the leading electricity exporter in Europe. Due to unavailability of virtually half of the Belgian nuclear fleet, 16.5 TWh of electricity was exported to Belgium (+28% against 2013). Sustained use of the interconnections especially confirmed the need to continue to adapt the power grid so that it can achieve the aims of energy transition embarked upon in France and in Europe. In order to contribute to this initiative and enable customers to receive clean, safe and cost-effective electricity, in 2014, RTE upheld its level of investment at Meuros 1,374, roughly the same amount as in 2013. All this information on consumption, generation, cross-border exchanges and CO 2 emissions can be consulted in real time on the new version of the general public application, eco2mix, available on smart phones, tablet computers and the RTE web site

  12. Areva - Press release from the Supervisory Board

    International Nuclear Information System (INIS)

    Marie, Patricia; Briand, Pauline; Floquet-Daubigeon, Fleur; Michaut, Maxime; Scorbiac, Marie de; Repaire, Philippine du

    2012-01-01

    During its meeting held on December 12, 2011, devoted in particular to the examination of the 2011 closing estimates, the AREVA Executive Board indicated that it expected to book a provision of 1.46 billion euros (2.025 billion US dollars) in the company's accounts for fiscal year 2011 for impairment of assets for the reporting entity UraMin, a mining company acquired by AREVA in 2007, which, given the provision booked in 2010 (426 million euros), brings the value of these assets on the AREVA balance sheet down to 410 million euros. Given the size of these provisions, the Supervisory Board decided to make three of its members, meeting as an ad hoc committee, in charge of analyzing the terms of acquisition of this company, as well as the key decisions made in this reporting entity up to 2011 and, based on the outcome of these analyses, to recommend to it any appropriate measures in AREVA's interest. This committee reported on its work during the Supervisory Board meeting held on February 14, 2012. In light of this report, the Supervisory Board found that the fairness and reliability of the financial statements of previous years were not in question. Nevertheless, considering the malfunctions raised, the Board considers it appropriate to thoroughly review AREVA's governance in order to ensure that decisions concerning large acquisitions or investments be reviewed and validated in the future under conditions ensuring better legal and financial security and enabling a more transparent dialogue between management and the Supervisory Board. It thus asked the Executive Board to recommend, at the next General Meeting of Shareholders, that the by-laws of the company be modified to make the Supervisory Board's prior approval of investments, stake acquisitions and acquisitions mandatory above a threshold of 20 million euros. It also decided to set up a business ethics committee within the Supervisory Board responsible for ensuring that rules of conduct are properly applied

  13. Volatile organic compound emissions during hot-pressing of southern pine particleboard : panel size effects and trade-off between press time and temperature

    Science.gov (United States)

    Wenlong Wang; Douglas J. Gardner; Melissa G.D. Baumann

    2002-01-01

    In previous research, it was shown that decreasing either press temperature or press time generally resulted in decreased volatile organic compound (VOC) emissions during the hot-pressing of southern pine particleboard. However, because it is impossible to reduce both pressing time and temperature while maintaining panel physical and mechanical properties, this study...

  14. Comparison of Myoelectric Activity of a Selection of Upper Extremity Muscles while Doing Bench Press in Two Training Methods of TRX and Barbell Bench Press

    Directory of Open Access Journals (Sweden)

    Ahmad Reza Zibaei

    2016-12-01

    Conclusion: Considering these results it can be maintained that TRX bench press resistance training can be an alternative and effective practice for barbell bench press because, given the results, it can be appreciated that TRX bench press, dips low in the trunk, can lead to muscle activity close to the level of muscle activity during the barbell bench press drill.

  15. Similar acute physiological responses from effort and duration matched leg press and recumbent cycling tasks

    Directory of Open Access Journals (Sweden)

    James Steele

    2018-02-01

    Full Text Available The present study examined the effects of exercise utilising traditional resistance training (leg press or ‘cardio’ exercise (recumbent cycle ergometry modalities upon acute physiological responses. Nine healthy males underwent a within session randomised crossover design where they completed both the leg press and recumbent cycle ergometer conditions. Conditions were approximately matched for effort and duration (leg press: 4 × 12RM using a 2 s concentric and 3 s eccentric repetition duration controlled with a metronome, thus each set lasted  60 s; recumbent cycle ergometer: 4 × 60 s bouts using a resistance level permitting 80–100 rpm but culminating with being unable to sustain the minimum cadence for the final 5–10 s. Measurements included VO2, respiratory exchange ratio (RER, blood lactate, energy expenditure, muscle swelling, and electromyography. Perceived effort was similar between conditions and thus both were well matched with respect to effort. There were no significant effects by ‘condition’ in any of the physiological responses examined (all p > 0.05. The present study shows that, when both effort and duration are matched, resistance training (leg press and ‘cardio’ exercise (recumbent cycle ergometry may produce largely similar responses in VO2, RER, blood lactate, energy expenditure, muscle swelling, and electromyography. It therefore seems reasonable to suggest that both may offer a similar stimulus to produce chronic physiological adaptations in outcomes such as cardiorespiratory fitness, strength, and hypertrophy. Future work should look to both replicate the study conducted here with respect to the same, and additional physiological measures, and rigorously test the comparative efficacy of effort and duration matched exercise of differing modalities with respect to chronic improvements in physiological fitness.

  16. Nonlinear Analysis of an Unstable Bench Press Bar Path and Muscle Activation.

    Science.gov (United States)

    Lawrence, Michael A; Leib, Daniel J; Ostrowski, Stephanie J; Carlson, Lara A

    2017-05-01

    Lawrence, MA, Leib, DJ, Ostrowski, SJ, and Carlson, LA. Nonlinear analysis of an unstable bench press bar path and muscle activation. J Strength Cond Res 31(5): 1206-1211, 2017-Unstable resistance exercises are typically performed to improve the ability of stabilizing muscles to maintain joint integrity under a load. The purpose of this study was to examine the effects of an unstable load (as provided by a flexible barbell and a load suspended by elastic bands) on the bar path, the primary musculature, and stabilizing musculature while bench pressing using nonlinear analyses. Fifteen resistance-trained men (age 24.2 ± 2.7 years, mass 84.1 ± 12.0 kg, height 1.77 ± 0.05 m, 9.9 ± 3.4 years of lifting experience, and bench press 1 repetition maximum (RM) 107.5 ± 25.9 kg) volunteered for this study. Subjects pressed 2 sets of 5 repetitions in both stable (total load 75% 1RM) and unstable (total load 60% 1RM) conditions using a standard barbell and a flexible Earthquake bar, respectively. Surface electromyography was used to detect muscle activity of primary movers (pectoralis major, anterior deltoid, and triceps) and bar stabilizing musculature (latissimus dorsi, middle and posterior deltoid, biceps brachii, and upper trapezius). During the unstable condition, the bar moved in more ways and was less predictable in the mediolateral and anteroposterior directions. However, the muscle activation patterns of all muscles were more constrained with the unstable barbell. These findings suggest that the unstable condition was more challenging to control, but subjects controlled the instability by contracting their muscles in a more stable pattern or "staying tight" throughout the exercise.

  17. A comparative study between spiral-filter press and belt press implemented in a cloudy apple juice production process.

    Science.gov (United States)

    De Paepe, Domien; Coudijzer, Katleen; Noten, Bart; Valkenborg, Dirk; Servaes, Kelly; De Loose, Marc; Diels, Ludo; Voorspoels, Stefan; Van Droogenbroeck, Bart

    2015-04-15

    In this study, advantages and disadvantages of the innovative, low-oxygen spiral-filter press system were studied in comparison with the belt press, commonly applied in small and medium size enterprises for the production of cloudy apple juice. On the basis of equivalent throughput, a higher juice yield could be achieved with spiral-filter press. Also a more turbid juice with a higher content of suspended solids could be produced. The avoidance of enzymatic browning during juice extraction led to an attractive yellowish juice with an elevated phenolic content. Moreover, it was found that juice produced with spiral-filter press demonstrates a higher retention of phenolic compounds during the downstream processing steps and storage. The results demonstrates the advantage of the use of a spiral-filter press in comparison with belt press in the production of a high quality cloudy apple juice rich in phenolic compounds, without the use of oxidation inhibiting additives. Copyright © 2014 Elsevier Ltd. All rights reserved.

  18. The Effects of Bench Press Variations in Competitive Athletes on Muscle Activity and Performance.

    Science.gov (United States)

    Saeterbakken, Atle Hole; Mo, Dag-André; Scott, Suzanne; Andersen, Vidar

    2017-06-01

    The aim of the study was to compare the EMG activity performing 6RM competition style bench press (flat bench-wide grip) with 1) medium and narrow grip widths on a flat bench and 1) inclined and declined bench positions with a wide grip. Twelve bench press athletes competing at national and international level participated in the study. EMG activity was measured in the pectoralis major, anterior and posterior deltoid, biceps brachii, triceps brachii and latissimus dorsi. Non-significant differences in activation were observed between the three bench positions with the exception of 58.5-62.6% lower triceps brachii activation, but 48.3-68.7% greater biceps brachii activation in the inclined bench compared with the flat and declined bench position. Comparing the three grip widths, non-significant differences in activations were observed, with the exception of 25.9-30.5% lower EMG activity in the biceps brachii using a narrow grip, compared to the medium and wide grip conditions. The 6-RM loads were 5.8-11.1% greater using a medium and wide grip compared to narrow grip width and 18.5-21.5% lower in the inclined bench position compared with flat and declined. Comparing the EMG activity during the competition bench press style with either the inclined and declined bench position (wide grip) or using a narrow and medium grip (flat bench), only resulted in different EMG activity in the biceps- and triceps brachii. The 6RM loads varied with each bench press variation and we recommend the use of a wide grip on a flat bench during high load hypertrophy training to bench press athletes.

  19. Movement Features Which Describe the Flat Bench Press

    Directory of Open Access Journals (Sweden)

    Król Henryk

    2017-06-01

    Full Text Available Introduction. In sport technique studies, motion features can be useful as they have a certain defined measure [1]. In this work, we examined the following three features: the structure of the movement (all the characteristics of the movement, the fluency of the movement, and the rhythm of the movement. The aim of the study was to determine the usefulness of the selected movement features in the evaluation of the flat bench press. The protocol of the study included a flat bench press with free weights and a “touch-and-go” technique. Material and methods. The study involved twenty healthy men; however, only two were selected for analysis. The first subject was a 25-year-old powerlifter (body mass = 95 kg; body height = 182 cm; 1-RM in flat bench press = 145 kg. The second one was a 25-year-old bodybuilder (body mass = 77 kg; body height = 175 cm; 1-RM in flat bench press = 100 kg. The subjects performed consecutive sets of a single repetition of flat bench pressing with an increasing load (70, 80, 90, and 100% 1-RM, with the anticipated maximum weight, until the completion of one repetition maximum. Multidimensional movement analysis was made with the measuring system Smart-E (BTS, Italy, which consisted of six infrared cameras (120 Hz and a wireless module to measure muscle bioelectric activity (Pocket EMG. Results. It was demonstrated that the internal structure of the bench press performed by the bodybuilder and the powerlifter was different. As the time-history of barbell kinematics (the acceleration-time curve showed, with increased loading of the barbell, the rhythm of the flat bench press changed, and the fluidity of the movement worsened.

  20. Freedom of the Press In the Scope of Human Rights

    Directory of Open Access Journals (Sweden)

    Sri Ayu Astuti

    2014-01-01

    Full Text Available Freedom of expression and press freedom is the embodiment of the recognition of human rights. Freedom of expression is also the existence of press to disclose the news with honesty and do not get a pressure to deliver the news to the public space, which in news production is known as a work of journalism. Now the  press has gained freedom of expression in the news production process which is guaranteed in the state constitution. Although Article 28 of the Constitution of the Republic of Indonesia 1945 does not point directly at the press, However, Article 28 F emphasis on processing and storage as well as ownership, excavations to information. It also contains provisions on the freedom of expression of others, which should be valued and respected. It shows equality for everyone in his position before the law in accordance with Article 27 1945 Constitution, which emphasizes the recognition of constitutional rights that belong to every person in the state of law in the Republic of Indonesia. Thus the press, which have freedom of expression in the writings of journalistic works are required to be responsible for the published news. So as not to face the legal issues and criminalization, then press should perform tasks and functions to enforce ethics as the precautionary principle when processing the news and broadcast it to the public space, as well as upholding human rights. How To Cite: Astuti, S. (2014. Freedom of the Press In the Scope of Human Rights. Rechtsidee, 1(1, 101-118. doi:http://dx.doi.org/10.21070/jihr.v1i1.96

  1. FeCrAl/Zr dual layer fuel cladding for improved safety margin under accident scenario

    International Nuclear Information System (INIS)

    Park, D.J.; Park, J.H.; Jung, Y.I.; Kim, H.G.; Park, J.Y.; Koo, Y.H.

    2014-01-01

    For application of advanced steel as a cladding material in light water reactor (LWR), FeCrAl/Zr dual layer tube was manufactured by using a hot isostatic pressing (HIP) method. To optimize HIP condition for joining both FeCrAl and Zr alloys, HIP was carried out under various temperature conditions. Tensile test and 3-point bend test performed for measuring mechanical properties of HIPed sample. To better understand microstructural characteristics in interface region between two alloys, SEM and TEM study were conducted by using HIPed sample with different process conditions. Based on this optimization study and analyzed results, optimized HIP condition was determined and FeCrAl/Zr dual layer fuel cladding having same wall thickness with current LWR fuel cladding was manufactured. Simulated loss-of-coolant accident test was carried out using FeCrAl/Zr dual layer cladding sample and fuel integrity was measured by mechanical test. (authors)

  2. Six-axis multi-anvil press for high-pressure, high-temperature neutron diffraction experiments

    Energy Technology Data Exchange (ETDEWEB)

    Sano-Furukawa, A., E-mail: sano.asami@jaea.go.jp; Hattori, T. [Quantum Beam Science Center, Japan Atomic Energy Agency, Ibaraki 319-1195 (Japan); J-PARC Center, Japan Atomic Energy Agency, Ibaraki 319-1195 (Japan); Arima, H. [Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Yamada, A. [The University of Shiga Prefecture, Shiga 522-8533 (Japan); Tabata, S.; Kondo, M.; Nakamura, A. [Sumitomo Heavy Industries Co., Ltd., Ehime 792-0001 (Japan); Kagi, H.; Yagi, T. [Geochemical Research Center, Graduate School of Science, The University of Tokyo, Tokyo 113-0033 (Japan)

    2014-11-15

    We developed a six-axis multi-anvil press, ATSUHIME, for high-pressure and high-temperature in situ time-of-flight neutron powder diffraction experiments. The press has six orthogonally oriented hydraulic rams that operate individually to compress a cubic sample assembly. Experiments indicate that the press can generate pressures up to 9.3 GPa and temperatures up to 2000 K using a 6-6-type cell assembly, with available sample volume of about 50 mm{sup 3}. Using a 6-8-type cell assembly, the available conditions expand to 16 GPa and 1273 K. Because the six-axis press has no guide blocks, there is sufficient space around the sample to use the aperture for diffraction and place an incident slit, radial collimators, and a neutron imaging camera close to the sample. Combination of the six-axis press and the collimation devices realized high-quality diffraction pattern with no contamination from the heater or the sample container surrounding the sample. This press constitutes a new tool for using neutron diffraction to study the structures of crystals and liquids under high pressures and temperatures.

  3. HIP (hot isostatic pressing) sintering of Tantalum (Ta) and tantalum carbide (TaC) powder mixture: relations between microstructure and properties

    International Nuclear Information System (INIS)

    Valin, F.; Schnedecker, M.

    1994-01-01

    HIP sintering at 1630 C and 195 MPa, during 2 hours, can be used for complete densification of mixtures of commercial tantalum carbide and tantalum powders. HIPed material properties are depending upon initial compositions. For C/Ta ratios inferior to 80%, the monocarbide structure is preserved. A partial ordering of the carbon vacancies will result, for TaC(0.80), in microhardness maximization. The microstructurally homogenous TaC(0.45) shows an excellent toughness. 2 figs., 2 refs

  4. Location of Instability During a Bench Press Alters Movement Patterns and Electromyographical Activity.

    Science.gov (United States)

    Nairn, Brian C; Sutherland, Chad A; Drake, Janessa D M

    2015-11-01

    Instability training devices with the bench press exercise are becoming increasingly popular. Typically, the instability device is placed at the trunk/upper body (e.g., lying on a Swiss ball); however, a recent product called the Attitube has been developed, which places the location of instability at the hands by users lifting a water-filled tube. Therefore, the purpose of this study was to analyze the effects of different instability devices (location of instability) on kinematic and electromyographical patterns during the bench press exercise. Ten healthy males were recruited and performed 1 set of 3 repetitions for 3 different bench press conditions: Olympic bar on a stable bench (BENCH), Olympic bar on a stability ball (BALL), and Attitube on a stable bench (TUBE). The eccentric and concentric phases were analyzed in 10% intervals while electromyography was recorded from 24 electrode sites, and motion capture was used to track elbow flexion angle and 3-dimensional movement trajectories and vertical velocity of the Bar/Attitube. The prime movers tended to show a reduction in muscle activity during the TUBE trials; however, pectoralis major initially showed increased activation during the eccentric phase of the TUBE condition. The trunk muscle activations were greatest during the TUBE and smallest during the BAR. In addition, the TUBE showed decreased range of elbow flexion and increased medial-lateral movement of the Attitube itself. The results further support the notion that instability devices may be more beneficial for trunk muscles rather than prime movers.

  5. Engaging and Supporting a University Press Scholarly Community

    Directory of Open Access Journals (Sweden)

    Megan Taylor

    2018-03-01

    Full Text Available In this paper we explore how the development of The University of Huddersfield Press, a publisher of open access scholarly journals and monographs, has enabled the sharing of research with a wider online audience. We situate the development of the Press within a wider research environment and growing community of New University Presses (NUPs where there is an increasing demand for demonstrating research impact, which drives the need for improved analysis and reporting of impact data, a task that often falls within the remit of library and academic support services. We detail the benefits of the University Press Manager role in terms of ensuring professional service that delivers consistency and sustainability. We go on to outline the experiences of engaging with different online spaces and detail the extensive support for student authors. We argue that in order for the Press to support building a strong and engaged scholarly community and provide new spaces for emerging research, continued investment in both platform development and infrastructure is required.

  6. Censoring the Press: A Barometer of Government Tolerance for Anti-regime Dissent under Authoritarian Rule

    Directory of Open Access Journals (Sweden)

    Elizabeth Ann Stein

    2016-01-01

    Full Text Available This paper proposes that dissident leaders aiming to build mass opposition movements follow the mainstream press to help them gauge government tolerance for anti-government mass actions in repressive authoritarian regimes. Under conditions of censorship, media–state interactions serve as a barometer of the government’s disposition toward and capacity to impede public displays of dissent. Observing trends in coverage and the government’s reaction to this coverage helps activist leaders assess when it should be safest to plan anti-government mass actions, such as demonstrations, marches, or strikes. Using original data derived from coding content from the Brazilian newspaper Folha de São Paulo over the period of 1974–1982, I test whether opposition mass actions followed trends in taboo content and government treatment of the press during the period of political liberalization of Brazil’s military regime.

  7. Thermoelectric Properties of Hot-Pressed and PECS-Sintered Magnesium-Doped Copper Aluminum Oxide

    Science.gov (United States)

    Liu, Chang; Morelli, Donald T.

    2011-05-01

    Copper aluminum oxide (CuAlO2) is considered as a potential candidate for thermoelectric applications. Partially magnesium-doped CuAlO2 bulk pellets were fabricated using solid-state reactions, hot-pressing, and pulsed electric current sintering (PECS) techniques. X-ray diffraction and scanning electron microscopy were adopted for structural analysis. High-temperature transport property measurements were performed on hot-pressed samples. Electrical conductivity increased with Mg doping before secondary phases became significant, while the Seebeck coefficient displayed the opposite trend. Thermal conductivity was consistently reduced as the Mg concentration increased. Effects of Mg doping, preparation conditions, and future modification on this material's properties are discussed.

  8. Acute chest pain after bench press exercise in a healthy young adult.

    Science.gov (United States)

    Smereck, Janet A; Papafilippaki, Argyro; Sudarshan, Sawali

    2016-01-01

    Bench press exercise, which involves repetitive lifting of weights to full arm extension while lying supine on a narrow bench, has been associated with complications ranging in acuity from simple pectoral muscle strain, to aortic and coronary artery dissection. A 39-year-old man, physically fit and previously asymptomatic, presented with acute chest pain following bench press exercise. Diagnostic evaluation led to the discovery of critical multivessel coronary occlusive disease, and subsequently, highly elevated levels of lipoprotein (a). Judicious use of ancillary testing may identify the presence of "high-risk" conditions in a seemingly "low-risk" patient. Emergency department evaluation of the young adult with acute chest pain must take into consideration an extended spectrum of potential etiologies, so as to best guide appropriate management.

  9. Numerical simulation of hot-pressed veneer products: Forming - Spring back – Distortion

    DEFF Research Database (Denmark)

    Ormarsson, Sigurdur; Sandberg, Dick

    2007-01-01

    Customers demand very high quality of veneered furniture products with regard to surface appearance, shape stability and stiffness. To meet these requirements, it is important to improve the manufacturing process by a better understanding of the thermo-hygro-mechanical behaviour of the individual...... veneers. During the manufacture of strongly curved products, the veneers are exposed to large membrane and bending deformations and to high pressure in the radial fibre direction. When hot-press forming is used, the veneers are also exposed to a high surface temperature during the pressing time (curing...... time). These severe conditions can result in plastic deformation perpendicular to the veneer surface as well as mechano-sorptive strains in the curved regions, since the heating can have a significant influence on the moisture distribution. How strong an influence these factors have on the distortion...

  10. Free-Weight Augmentation With Elastic Bands Improves Bench Press Kinematics in Professional Rugby Players.

    Science.gov (United States)

    García-López, David; Hernández-Sánchez, Sonsoles; Martín, Esperanza; Marín, Pedro J; Zarzosa, Fernando; Herrero, Azael J

    2016-09-01

    García-López, D, Hernández-Sánchez, S, Martín, E, Marín, PJ, Zarzosa, F, and Herrero, AJ. Free-weight augmentation with elastic bands improves bench press kinematics in professional rugby players. J Strength Cond Res 30(9): 2493-2499, 2016-This study aimed to investigate the effects of combining elastic bands to free weight resistance (EB + FWR) on the acceleration-deceleration and velocity profiles of the bench press in professional rugby players and recreationally trained subjects. Sixteen male subjects (8 rugby players and 8 recreationally trained subjects) were randomly assigned to complete 2 experimental conditions in a crossover fashion: EB + FWR and FWR. In both conditions, subjects performed 1 bench press set to volitional exhaustion with a load equivalent to the 85% of 1 repetition maximum (1RM). In the EB + FWR condition, the contribution of elastic resistance was approximately 20% of the selected load (85% 1RM). Results indicate that EB + FWR condition increased significantly the range of concentric movement in which the barbell is accelerated. This increase was significantly higher in rugby players (35%) in comparison with recreationally trained subjects (13%). Maximal velocity was also increased in EB + FWR (17%), when compared with FWR condition. These results suggest that when combined with variable resistance (i.e., EB), the external resistance seems to be more evenly distributed over the full range of motion, decreasing the need for dramatic deceleration at the end of the concentric phase. The present data also indicate that the kinematic benefits of an EB + FWR approach seems to be more prominent in athletes from modalities in which high level of strength and power are required (i.e., rugby players).

  11. Influence of bench angle on upper extremity muscular activation during bench press exercise.

    Science.gov (United States)

    Lauver, Jakob D; Cayot, Trent E; Scheuermann, Barry W

    2016-01-01

    This study compared the muscular activation of the pectoralis major, anterior deltoid and triceps brachii during a free-weight barbell bench press performed at 0°, 30°, 45° and -15° bench angles. Fourteen healthy resistance trained males (age 21.4 ± 0.4 years) participated in this study. One set of six repetitions for each bench press conditions at 65% one repetition maximum were performed. Surface electromyography (sEMG) was utilised to examine the muscular activation of the selected muscles during the eccentric and concentric phases. In addition, each phase was subdivided into 25% contraction durations, resulting in four separate time points for comparison between bench conditions. The sEMG of upper pectoralis displayed no difference during any of the bench conditions when examining the complete concentric contraction, however differences during 26-50% contraction duration were found for both the 30° [122.5 ± 10.1% maximal voluntary isometric contraction (MVIC)] and 45° (124 ± 9.1% MVIC) bench condition, resulting in greater sEMG compared to horizontal (98.2 ± 5.4% MVIC) and -15 (96.1 ± 5.5% MVIC). The sEMG of lower pectoralis was greater during -15° (100.4 ± 5.7% MVIC), 30° (86.6 ± 4.8% MVIC) and horizontal (100.1 ± 5.2% MVIC) bench conditions compared to the 45° (71.9 ± 4.5% MVIC) for the whole concentric contraction. The results of this study support the use of a horizontal bench to achieve muscular activation of both the upper and lower heads of the pectoralis. However, a bench incline angle of 30° or 45° resulted in greater muscular activation during certain time points, suggesting that it is important to consider how muscular activation is affected at various time points when selecting bench press exercises.

  12. TA-03-0035 Press Building – D&D

    Energy Technology Data Exchange (ETDEWEB)

    Hasenack, Marvin Leroy [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-11-02

    The Press Building was constructed in 1954 with 15,073 ft2 of floor space. It was built to house a 5000 ton double action Lake Erie hydraulic press and a uranium casting area. Missions included uranium activities associated with the Nuclear Weapons and Rover Rocket programs. At the end of the Rover program, the building continued to support various uranium materials science projects until the building was placed into a cold and dark status in 2013 and then was demolished in 2017. The building interior, the press, and associated systems were radiological contaminated and disposed of as low level waste. The demolition of this building opened up valuable real estate in the TA-3 area for the future construction of an ~11,000 Sq. Ft. Biosafety Level 2 laboratory and office building. This building will support the ongoing Bioscience Division mission at the laboratory.

  13. Natural Hazards and the press in the western Mediterranean region

    Directory of Open Access Journals (Sweden)

    M. Llasat-Botija

    2007-07-01

    Full Text Available This study analyses press articles published between 1982 and 2005 in an attempt to describe the social perception of natural hazards in Catalonia. The articles included in the database have been classified according to different types of risk. In addition, the study examines the evolution of each type of risk in the press coverage during the study period. Finally, the results have been compared to data provided by insurance companies with respect to compensations paid out for damages. Conclusions show that floods are the most important natural hazard in the region, but that the number of headlines for each event is greater in the case of snowfalls and forest fires. Factors such as the season of the year, the proximity of the affected region to the capital, the topical issues at the time, and the presence of other important news must be considered when the impact in the press is analysed.

  14. Asynchronous decision making in a memorized paddle pressing task.

    Science.gov (United States)

    Dankert, James R; Olson, Byron; Si, Jennie

    2008-12-01

    This paper presents a method for asynchronous decision making using recorded neural data in a binary decision task. This is a demonstration of a technique for developing motor cortical neural prosthetics that do not rely on external cued timing information. The system presented in this paper uses support vector machines and leaky integrate-and-fire elements to predict directional paddle presses. In addition to the traditional metrics of accuracy, asynchronous systems must also optimize the time needed to make a decision. The system presented is able to predict paddle presses with a median accuracy of 88% and all decisions are made before the time of the actual paddle press. An alternative bit rate measure of performance is defined to show that the system proposed here is able to perform the task with the same efficiency as the rats.

  15. The regulation of press freedoms (1863-1867

    Directory of Open Access Journals (Sweden)

    Laurence Coudart

    2015-10-01

    Full Text Available The main objective of this essay is to analyze the legislation affecting the press during the French Intervention and the Second Mexican Empire and establish their regulatory effects. These regulations are frequently ignored by the historiography. The article is limited to the origins, innovations, mechanisms and evolution of printing regulations during this period. As a whole, this allows the reader to observe the restrictive conception of press freedom held by the Mexican political class and their willingness, during the second half of the 19th Century, to turn to prohibitive, repressive, authoritarian and centralist legislation. The article also reveals the extent to which Imperial legislation and its logic of censorship were neither unprecedented nor sudden foreign impositions but instead the expressions of a long-lasting desire for government control over the press.

  16. Method for hot pressing irregularly shaped refractory articles

    Science.gov (United States)

    Steinkamp, William E.; Ballard, Ambrose H.

    1982-01-01

    The present invention is directed to a method for hot pressing irregularly haped refractory articles with these articles of varying thickness being provided with high uniform density and dimensional accuracy. Two partially pressed compacts of the refractory material are placed in a die cavity between displaceable die punches having compact-contacting surfaces of the desired article configuration. A floating, rotatable block is disposed between the compacts. The displacement of the die punches towards one another causes the block to rotate about an axis normal to the direction of movement of the die punches to uniformly distribute the pressure loading upon the compacts for maintaining substantially equal volume displacement of the powder material during the hot pressing operation.

  17. Advertising presence on the visual configuration of the digital press

    Directory of Open Access Journals (Sweden)

    Belinda de Frutos Torres

    2016-07-01

    Full Text Available Visual strength is responsible for one of the mayor changes undergone by the digital press with Internet explosion and the increase of the Informational and Communicational Technologies. The present study analyzes the structure the digital press has taken and the role of the digital advertisement in the composition of their textual and iconic elements. The paper quantifies the picture representations volume and compares their presence on the digital natives papers with those coming from the traditional paper support. The results reveal that there is a mayor contribution of adverts on the native on-line press compare to the on-line paper arriving from the traditional media decreasing the information volume. At the same time the visual volume is boosted on the former compare to the digital media with a paper support. Altogether it can be said that visual component prompted the digital papers first page, being this effect enhanced on the native digital papers.

  18. Film Advertising in the Albanian Press before World War II

    Directory of Open Access Journals (Sweden)

    Vjollca Hysi Panajoti

    2015-05-01

    Full Text Available This paper aims at studying the development of film advertising in the 1930’s Albanian press. Through advertising we struggle to read a piece of the Albanian monarchy’s history. Considering advertising as a historical source tends to reflect the economic, social and cultural life of the country. The study focused on the features, characteristics and uniqueness of advertising the films in relation to other ads present in print. Who were the people who created the ads, how does the Albanian press film advertising compare to advertising in the foreign press and what were the difficulties facing advertising at this time, are the other important issues addressed in this study. Over a century has passed since Harper's Weekly wrote that 'advertisements are a reflection of real life, a kind of fossil by which chroniclers can rewrite history in order to complete the graphic, even if all other historical evidence may have disappeared.

  19. A systematic review of surface electromyography analyses of the bench press movement task.

    Directory of Open Access Journals (Sweden)

    Petr Stastny

    Full Text Available The bench press exercise (BP plays an important role in recreational and professional training, in which muscle activity is an important multifactorial phenomenon. The objective of this paper is to systematically review electromyography (EMG studies performed on the barbell BP exercise to answer the following research questions: Which muscles show the greatest activity during the flat BP? Which changes in muscle activity are related to specific conditions under which the BP movement is performed?PubMed, Scopus, Web of Science and Cochrane Central Register of Controlled Trials (CENTRAL in the Cochrane Library were searched through June 10, 2016. A combination of the following search terms was used: bench press, chest press, board press, test, measure, assessment, dynamometer, kinematics and biomechanics. Only original, full-text articles were considered.The search process resulted in 14 relevant studies that were included in the discussion. The triceps brachii (TB and pectoralis major (PM muscles were found to have similar activity during the BP, which was significantly higher than the activity of the anterior deltoid. During the BP movement, muscle activity changes with exercise intensity, velocity of movement, fatigue, mental focus, movement phase and stability conditions, such as bar vibration or unstable surfaces. Under these circumstances, TB is the most common object of activity change.PM and TB EMG activity is more dominant and shows greater EMG amplitude than anterior deltoid during the BP. There are six factors that can influence muscle activity during the BP; however, the most important factor is exercise intensity, which interacts with all other factors. The research on muscle activity in the BP has several unresolved areas, such as clearly and strongly defined guidelines to perform EMG measurements (e.g., how to elaborate with surface EMG limits or guidelines for the use of exact muscle models.

  20. A systematic review of surface electromyography analyses of the bench press movement task.

    Science.gov (United States)

    Stastny, Petr; Gołaś, Artur; Blazek, Dusan; Maszczyk, Adam; Wilk, Michał; Pietraszewski, Przemysław; Petr, Miroslav; Uhlir, Petr; Zając, Adam

    2017-01-01

    The bench press exercise (BP) plays an important role in recreational and professional training, in which muscle activity is an important multifactorial phenomenon. The objective of this paper is to systematically review electromyography (EMG) studies performed on the barbell BP exercise to answer the following research questions: Which muscles show the greatest activity during the flat BP? Which changes in muscle activity are related to specific conditions under which the BP movement is performed? PubMed, Scopus, Web of Science and Cochrane Central Register of Controlled Trials (CENTRAL) in the Cochrane Library were searched through June 10, 2016. A combination of the following search terms was used: bench press, chest press, board press, test, measure, assessment, dynamometer, kinematics and biomechanics. Only original, full-text articles were considered. The search process resulted in 14 relevant studies that were included in the discussion. The triceps brachii (TB) and pectoralis major (PM) muscles were found to have similar activity during the BP, which was significantly higher than the activity of the anterior deltoid. During the BP movement, muscle activity changes with exercise intensity, velocity of movement, fatigue, mental focus, movement phase and stability conditions, such as bar vibration or unstable surfaces. Under these circumstances, TB is the most common object of activity change. PM and TB EMG activity is more dominant and shows greater EMG amplitude than anterior deltoid during the BP. There are six factors that can influence muscle activity during the BP; however, the most important factor is exercise intensity, which interacts with all other factors. The research on muscle activity in the BP has several unresolved areas, such as clearly and strongly defined guidelines to perform EMG measurements (e.g., how to elaborate with surface EMG limits) or guidelines for the use of exact muscle models.

  1. A systematic review of surface electromyography analyses of the bench press movement task

    Science.gov (United States)

    Gołaś, Artur; Blazek, Dusan; Maszczyk, Adam; Wilk, Michał; Pietraszewski, Przemysław; Petr, Miroslav; Uhlir, Petr; Zając, Adam

    2017-01-01

    Background The bench press exercise (BP) plays an important role in recreational and professional training, in which muscle activity is an important multifactorial phenomenon. The objective of this paper is to systematically review electromyography (EMG) studies performed on the barbell BP exercise to answer the following research questions: Which muscles show the greatest activity during the flat BP? Which changes in muscle activity are related to specific conditions under which the BP movement is performed? Strategy PubMed, Scopus, Web of Science and Cochrane Central Register of Controlled Trials (CENTRAL) in the Cochrane Library were searched through June 10, 2016. A combination of the following search terms was used: bench press, chest press, board press, test, measure, assessment, dynamometer, kinematics and biomechanics. Only original, full-text articles were considered. Results The search process resulted in 14 relevant studies that were included in the discussion. The triceps brachii (TB) and pectoralis major (PM) muscles were found to have similar activity during the BP, which was significantly higher than the activity of the anterior deltoid. During the BP movement, muscle activity changes with exercise intensity, velocity of movement, fatigue, mental focus, movement phase and stability conditions, such as bar vibration or unstable surfaces. Under these circumstances, TB is the most common object of activity change. Conclusions PM and TB EMG activity is more dominant and shows greater EMG amplitude than anterior deltoid during the BP. There are six factors that can influence muscle activity during the BP; however, the most important factor is exercise intensity, which interacts with all other factors. The research on muscle activity in the BP has several unresolved areas, such as clearly and strongly defined guidelines to perform EMG measurements (e.g., how to elaborate with surface EMG limits) or guidelines for the use of exact muscle models. PMID

  2. Comparison of concentric and eccentric bench press repetitions to failure.

    Science.gov (United States)

    Kelly, Stephen B; Brown, Lee E; Hooker, Steven P; Swan, Pamela D; Buman, Matthew P; Alvar, Brent A; Black, Laurie E

    2015-04-01

    Eccentric muscle actions (ECC) are characterized by muscle lengthening, despite actin-myosin crossbridge formation. Muscles acting eccentrically are capable of producing higher levels of force compared with muscles acting concentrically. The purpose of this study was to determine whether ECC bench press yields greater strength than concentric (CON) as determined by 1 repetition maximum (1RM). Additionally, a comparison was made examining differences in the number of repetitions to failure at different relative intensities of 1RM. Thirty healthy men (age = 24.63 ± 5.6 years) were tested for 1RM in CON and ECC bench press and the number of repetitions completed at 60, 70, 80, and 90% 1RM. For CON repetitions, the weight was mechanically lowered to the chest, and the participant pressed it up until the elbows were fully extended. The ECC bench press consisted of lowering a barbell from a fully extended elbow position to the chest in a continuous controlled manner for 3 seconds as determined by electronic metronome. Paired t-tests showed that ECC 1RM (115.99 ± 31.08 kg) was significantly (p ≤ 0.05) greater than CON 1RM (93.56 ± 26.56 kg), and the number of repetitions completed at 90% 1RM was significantly (p ≤ 0.05) greater in ECC (7.67 ± 3.24) as compared with CON (4.57 ± 2.21). There were no significant differences in number of completed repetitions during CON and ECC bench press at 60, 70, and 80% 1RM. These data indicate that ECC actions yield increased force capabilities (∼120%) as compared with CON in the bench press and may be less prone to fatigue, especially at higher intensities. These differences suggest a need to develop unique strategies for training eccentrically.

  3. Factors influencing the creep strength of hot pressed beryllium

    International Nuclear Information System (INIS)

    Webster, D.; Crooks, D.D.

    1975-01-01

    The parameters controlling the creep strength of hot pressed beryllium block have been determined. Creep strength was improved by a high initial dislocation density, a coarse grain size, and a low impurity content. The impurities most detrimental to creep strength were found to be aluminum, magnesium, and silicon. A uniform distribution of BeO was found to give creep strength which was inferior to a grain boundary distribution. The creep strength of very high purity, hot isostatically pressed beryllium was found to compare favorably with that of other more commonly used high temperature metals

  4. Vacuum hot pressing of titanium-alloy powders

    International Nuclear Information System (INIS)

    Malik, R.K.

    1975-01-01

    Full or nearly full dense products of wrought-metal properties have been obtained by vacuum hot pressing (VHP) of several prealloyed Ti--6Al--4V powders including hydride, hydride/dehydride, and rotating electrode process (REP) spherical powder. The properties of billets VHP from Ti--6Al--4V hydride powder and from hydride/dehydride powders have been shown to be equivalent. The REP spherical powder billets processed by VHP or by hot isostatic pressing (HIP) resulted in equivalent tensile properties. The potential of VHP for fabrication of near net aircraft parts such as complex fittings and engine disks offers considerable cost savings due to reduced material and machining requirements

  5. Equal channel angular pressing of pure aluminium—an analysis

    Indian Academy of Sciences (India)

    Abstract. Equal channel angular pressing (ECAP) is a novel technique for producing ultra fine grain struc- tures in submicron level by introducing a large amount of shear strain into the materials without changing the billet shape or dimensions. This process is well suited for aluminium alloys and is capable of producing ultra.

  6. EMG analysis and modelling of flat bench press using artificial ...

    African Journals Online (AJOL)

    The objective of this study was to evaluate the contribution of particular muscle groups during the Flat Bench Press (FBP) with different external loads. Additionally, the authors attempted to determine whether regression models or Artificial Neural Networks (ANNs) can predict FBP results more precisely and whether they can ...

  7. Democratic Socialism: Toward a Fifth Theory of the Press.

    Science.gov (United States)

    Picard, Robert G.

    For more than 25 years, the "four theories" paradigm has been dominant in the study of the relationships among the press, society, and the state. Asserting that the major approaches to such study are the libertarian, social responsibility, authoritarian, and Soviet/communist theories, this paradigm fails to account for economic and…

  8. "...Establish the Student Press--And Stifle It!"

    Science.gov (United States)

    McCallie, Franklin

    1990-01-01

    Presents an acceptance speech by Franklin McCallie, principal of Kirkwood High School (Missouri), for the "Administrator of the Year" award presented by the Missouri Interscholastic Press Association and the Missouri Journalism Education Association in April 1989. Discusses journalism's role in achieving the school's chief goals: student growth,…

  9. Picture This: 4-H Press Corps Builds Life Skills

    Science.gov (United States)

    Clary, Christy D.

    2018-01-01

    A picture is worth a thousand words! Extension professionals are often looking for the picture that best captures an event and tells its story. Look beneath the surface, though, and a picture is worth much more. Developing a 4-H press corps results in a collection of useful photos but has the added benefit of providing 4-H members with an…

  10. Water holding capacity and enzymatic modification of pressed potato fibres

    NARCIS (Netherlands)

    Ramasamy, U.

    2014-01-01

    Cell wall polysaccharides (CWPs) contribute to the water holding capacity (WHC) of fibre rich feeds, such as pressed potato fibres (PPF). However, the role of CWPs on the WHC of PPF was unidentified so far.

    PPF was characterized to be abundant in arabinogalactan (AG) linked

  11. Quid pro quo: tobacco companies and the black press.

    Science.gov (United States)

    McCandless, Phyra M; Yerger, Valerie B; Malone, Ruth E

    2012-04-01

    We explored the relationship between tobacco companies and the Black press, which plays an important role in conveying information and opinions to Black communities. In this archival case study, we analyzed data from internal tobacco industry documents and archives of the National Newspaper Publishers Association (NNPA), the trade association of the Black press. In exchange for advertising dollars and other support, the tobacco industry expected and received support from Black newspapers for tobacco industry policy positions. Beginning in the 1990s, resistance from within the Black community and reduced advertising budgets created counterpressures. The tobacco industry, however, continued to sustain NNPA support. The quid pro quo between tobacco companies and the Black press violated journalistic standards and represented an unequal trade. Although numerous factors explain today's tobacco-related health disparities, the Black press's service to tobacco companies is problematic because of the trust that the community placed in such media. Understanding the relationship between the tobacco industry and the NNPA provides insight into strategies that the tobacco industry may use in other communities and countries.

  12. The nuclear issue in the cuban press. Challenges and realities

    International Nuclear Information System (INIS)

    Contreras Izquierdo, Marta; Rodriguez Guerra, Ingrids; Gonzalez Montoto, Iosbel; Fernandez Rondon, Manuel

    2005-01-01

    The work presents an analysis of the impact of nuclear issue on the Cuban press from 1990 to 2005 that was carried out by a group of communications specialists from nuclear area. An analysis of main challenges and actions of this group, aimed at informing the public the present situation of the Cuban nuclear programme and its perspectives, was also included

  13. Finishing procedures action on mechanical characteristics of pressed ceramics

    Directory of Open Access Journals (Sweden)

    Mohamed Abdel Moniem Ahmed

    2018-06-01

    Conclusions& significance: Grinding & finishing procedures of pressed ceramics showed significant effect Of drill speed and polishing technique over flexural strength, As Grinding with no finishing and polishing procedure showed lowest flexural Strength values followed by finishing and polishing procedure followed by finishing and polishing with polishing paste procedure.

  14. Process considerations for hot pressing ceramic nuclear waste forms

    International Nuclear Information System (INIS)

    Wilson, C.N.; Brite, D.W.

    1981-01-01

    Spray calcined simulated ceramic nuclear waste powders were hot pressed in graphite, nickel-lined graphite and ZrO 2 -lined Al 2 O 3 dies. Densification, initial off-gas, waste element retention and pellet-die interactions were evaluated. Indicated process considerations and limitations are discussed. 15 figures

  15. Press Ideology and Organizational Control in Hong Kong.

    Science.gov (United States)

    Chan, Joseph Man; Lee, Chin-Chuan

    1988-01-01

    Surveys the entire Chinese journalist population of Hong Kong to determine how news organizations in the highly politicized environment of Hong Kong exercise institutional control on recruitment and newswork. Finds that press ideology is a major determinant of its organizational control. (MS)

  16. Nanoindentation hardness of hot-pressed boron suboxide

    International Nuclear Information System (INIS)

    Machaka, Ronald; Derry, Trevor E.; Sigalas, Iakovos

    2011-01-01

    Highlights: → The load-displacement indentation response of hot-pressed B 6 O is measured and analysed. → The nanoindentation hardness of hot-pressed boron suboxide is reported. → An approach is developed to simulate multi-cycling loading load-displacement curves. → A comprehensive model inter-comparison study of the ISE in hot-pressed B 6 O is also presented. → The fractal dimension is a better measure of ISE than the Meyer's index. - Abstract: The existence of the indentation size effect implies the absence of a single hardness value for the material under investigation especially at low applied loads. In this paper we present an investigation of the indentation size dependence behaviour of nanoindentation hardness in boron suboxide ceramic compacts prepared by uniaxial hot-pressing. Berkovich nanohardness indentations were conducted and analyzed accordingly. In addition to the ordinary Oliver and Pharr method of nanoindentation data analysis, a quantitative approach for the loading curve analysis is proposed. Using the proposed approach, the description and characterization of the observed indentation size effect through the application of the Meyer's law, and the classical and the modified proportional specimen resistance models as well as the multi-fractal scaling law was conducted and is reported. The load-independent hardness values deduced from our quantitative approach are comparable to the results calculated with conventional methods, especially with the multi-fractal scaling law.

  17. Press travel to the Mochovce power plant in Slovakia

    International Nuclear Information System (INIS)

    1998-07-01

    This press dossier gives, first, a general presentation of the Mochovce power plant of the republic of Slovakia (history, technical characteristics, safety aspects, technical particularities of VVER 440/213 reactors (safety analysis, recent improvements), financing of the modernization project). Then, the activities of the Framatome group in central and eastern Europe are presented (partnerships, cooperation agreements and contracts). (J.S.)

  18. Constitutional Provisions on the Press: A World View.

    Science.gov (United States)

    Paraschos, Manny

    A study examined the legal treatment of the press in constitutions or other basic legal institutional documents from around the world. Sixty-three constitutions or basic documents from the Western World, the Communist Bloc, the Middle East, Africa, Southeast Asia, and Latin America were analyzed. Analysis revealed that most constitutions open with…

  19. The Surrender of Tobruk in 1942: Press reports and soldiers ...

    African Journals Online (AJOL)

    The British and South African papers began to demand answers from politicians and military leaders for this shocking and unexpected catastrophe. The press ... Keywords: Prisoners of war (POWs), World War II, Union Defence Force, Erwin Rommel, Auchinleck, Ritchie, HB Klopper, South Africa, Eighth Army, Gazala ...

  20. Toward a Normative Theory of Freedom of the Press.

    Science.gov (United States)

    Jensen, Dwight Wm.

    In considering the possibility of a normative theory of freedom of the press, this paper examines arguments about such freedom in the Third World and elsewhere. Some of the arguments discussed in the paper are derived from the theories of John Locke and Karl Marx; others are drawn from the concepts of divine rights, elitism, liberal democracy, and…

  1. Back-pressure Forging Using a Servo Press

    OpenAIRE

    河本, 基一郎; Kawamoto, Kiichiro

    2015-01-01

    博士論文要旨Abstract 以下に掲載:International Journal of Automation Technology 9(2) pp.184-192 2015. Fuji Technology Press Ltd. 共著者:Kiichiro Kawamoto, Takeshi Yoneyama, Masato Okada

  2. Nanoindentation hardness of hot-pressed boron suboxide

    Energy Technology Data Exchange (ETDEWEB)

    Machaka, Ronald, E-mail: Ronald.Machaka@wits.ac.za [DST/NRF Centre of Excellence in Strong Materials, University of the Witwatersrand, P. Bag 3, Wits, Johannesburg (South Africa); School of Chemical and Metallurgical Engineering, University of the Witwatersrand, P.O. Bag 3, Wits, Johannesburg 2050 (South Africa); Derry, Trevor E. [DST/NRF Centre of Excellence in Strong Materials, University of the Witwatersrand, P. Bag 3, Wits, Johannesburg (South Africa); School of Physics, University of the Witwatersrand, P.O. Bag 3, Wits, Johannesburg 2050 (South Africa); Sigalas, Iakovos [DST/NRF Centre of Excellence in Strong Materials, University of the Witwatersrand, P. Bag 3, Wits, Johannesburg (South Africa); School of Chemical and Metallurgical Engineering, University of the Witwatersrand, P.O. Bag 3, Wits, Johannesburg 2050 (South Africa)

    2011-07-15

    Highlights: {yields} The load-displacement indentation response of hot-pressed B{sub 6}O is measured and analysed. {yields} The nanoindentation hardness of hot-pressed boron suboxide is reported. {yields} An approach is developed to simulate multi-cycling loading load-displacement curves. {yields} A comprehensive model inter-comparison study of the ISE in hot-pressed B{sub 6}O is also presented. {yields} The fractal dimension is a better measure of ISE than the Meyer's index. - Abstract: The existence of the indentation size effect implies the absence of a single hardness value for the material under investigation especially at low applied loads. In this paper we present an investigation of the indentation size dependence behaviour of nanoindentation hardness in boron suboxide ceramic compacts prepared by uniaxial hot-pressing. Berkovich nanohardness indentations were conducted and analyzed accordingly. In addition to the ordinary Oliver and Pharr method of nanoindentation data analysis, a quantitative approach for the loading curve analysis is proposed. Using the proposed approach, the description and characterization of the observed indentation size effect through the application of the Meyer's law, and the classical and the modified proportional specimen resistance models as well as the multi-fractal scaling law was conducted and is reported. The load-independent hardness values deduced from our quantitative approach are comparable to the results calculated with conventional methods, especially with the multi-fractal scaling law.

  3. Press-fit bipolar radial head arthroplasty, midterm results

    NARCIS (Netherlands)

    Kodde, Izaäk F.; Heijink, Andras; Kaas, Laurens; Mulder, Paul G. H.; van Dijk, C. Niek; Eygendaal, Denise

    2016-01-01

    Theoretical advantages of bipolar compared with monopolar radial head arthroplasty include better accommodation of radiocapitellar malalignment, reduction of capitellar abrasion, and reduction of stress at the bone-implant interfaces. Our purpose was to report the midterm results of press-fit

  4. Book Review: Stars (Copyright 1985, Golden Press; New York)

    Science.gov (United States)

    Marigza, R. N., Jr.

    2009-06-01

    Stars is a part of the Golden Guides collection produced by Golden Press. It is a small 160 page paperback guide to the constellations, the sun, the moon, planets, and other celestial bodies. The book is convenient to carry along wherever you go, making it an easy to access reference material.

  5. Ethics and the Press: Readings in Mass Media Morality.

    Science.gov (United States)

    Merrill, John C., Ed.; Barney, Ralph D., Ed.

    This collection of 35 articles addresses the topic of the ethical considerations and implications involved in reporting the news. Included in this book are such articles as: "Ethics and Journalism" by John Merrill, "Quality in Mass Communications" by Wilbur Schramm, "The American Press: Some Truths About Truths" by…

  6. MICROSTRUCTURAL ANALYSIS OF HOT ISOSTATICALLY PRESSED AL-SIC

    NARCIS (Netherlands)

    Bronsveld, P.M.; Hosson, J.Th. De; Sargent, M.A.; Alsem, W.H.M.

    1991-01-01

    The difference between extruded and hot isostatically pressed (HIP) Al6061 both with a T6 final heat treatment and with a 30 wt.% SiC particulate reinforcement is one of densification. The higher density of the HIP material is not translated into a stronger material. The Mg2Si precipitation is

  7. FREEDOM OF SPEECH IN INDONESIAN PRESS: INTERNATIONAL HUMAN RIGHTS PERSPECTIVE

    Directory of Open Access Journals (Sweden)

    Clara Staples

    2016-06-01

    Full Text Available This paper will firstly examine the international framework of human rights law and its guidelines for safeguarding the right to freedom of speech in the press. Secondly, it will describe the constitutional and other legal rights protecting freedom of speech in Indonesia and assess their compatibility with the right to freedom of speech under the international human rights law framework. Thirdly it will consider the impact of Indonesia’s constitutional law and criminal and civil law, including sedition and defamation laws, and finally media ownership, on the interpretation and scope of the right to freedom of speech in the press. Consideration of these laws will be integrated with a discussion of judicial processes. This discussion will be used to determine how and in what circumstances the constitutional right to freedom of speech in the press may be facilitated or enabled, or on the other hand, limited, overridden or curtailed in Indonesia. Conclusions will then be drawn regarding the strengths and weaknesses of Indonesian laws in safeguarding the right to freedom of speech in the press and the democratic implications from an international human rights perspective. This inquiry will be restricted to Indonesian laws in existence during the post-New Order period of 1998 to the present, and to the information and analysis provided by English-language sources.

  8. The Press of the Soviet Union: A Bibliography.

    Science.gov (United States)

    Bergethon, Bruce; And Others

    Compiled in response to the need for more information on the differences between the press systems of the United States and the Soviet Union, this bibliography contains 240 entries. Consisting of newspaper articles, journal articles, books, and pamphlets, the bibliography provides an overview of the different journalistic philosophies of the two…

  9. Introducing Collabra, OA Journal from University of California Press

    OpenAIRE

    Morgan, Daniel

    2015-01-01

    An introductory presentation of Collabra, the open access mega journal from University of California Press, highlighting its unique business model which shares and spreads revenue back to the research community. (Presented at the FORCE 2015 conference at the University of Oxford, January 13, 2015.)

  10. Student Press and Distribution Issues: Rights and Responsibilities.

    Science.gov (United States)

    Bartlett, Larry D.

    1984-01-01

    This review analyzes case law in the area of student press and distribution and offers some guidelines for developing and implementing school policy and rules. Litigation is reviewed in order to clarify students' rights, limitations on administrative authority in matters of censorship and prior restraint, and actions in connection with writing and…

  11. Performing “responsibility” and “conspiracy” through press ...

    African Journals Online (AJOL)

    In 2003, the Australian cricketer Shane Warne was suspected and convicted of doping. The purpose of this article was to understand how he tried to resolve the problem/dilemma of being suspected and convicted of doping through three press statements, which he delivered to the media during the 2003 Cricket World Cup ...

  12. Pleurotus pulmonarius cultivation on amended palm press fibre waste

    African Journals Online (AJOL)

    In the last few decades, rapid global demand for edible oils has resulted in a significant increase in the land area of oil crop cultivation. In the process of extraction of palm oil from oil palm fruit, biomass materials such as palm pressed fibre (PPF) are generated as waste products. This research was undertaken to evaluate ...

  13. The Press, the Government, and the Ethics Vacuum.

    Science.gov (United States)

    Merrill, John C.

    Immanuel Kant's idea of a will to do the right thing--to be ethical--is essentially a dead concept with both press and government. The reasons for this "ethics vacuum" are two-fold: the foundations of ethics in both circles are vague, confusing, and beset by relativism and pragmatism so that no system of ethics ever really coalesces; and neither…

  14. Experiments on rocks under high pressure conditions in GTA 20-32 triaxial press

    Czech Academy of Sciences Publication Activity Database

    Poláček, J.; Kožušníková, Alena

    2012-01-01

    Roč. 58, č. 1 (2012), s. 9-16 ISSN 1802-5420 Institutional support: RVO:68145535 Keywords : triaxial stress * deformation * rocks Subject RIV: DH - Mining, incl. Coal Mining http://gse.vsb.cz/2012/LVIII-2012-1-09-16.pdf

  15. The Effect of Rest Interval Length on Repetition Consistency and Perceived Exertion During Near Maximal Loaded Bench Press Sets.

    Science.gov (United States)

    Scudese, Estevão; Willardson, Jeffrey M; Simão, Roberto; Senna, Gilmar; de Salles, Belmiro F; Miranda, Humberto

    2015-11-01

    The purpose of this study was to compare different rest intervals between sets on repetition consistency and ratings of perceived exertion (RPE) during consecutive bench press sets with an absolute 3RM (3 repetition maximum) load. Sixteen trained men (23.75 ± 4.21 years; 74.63 ± 5.36 kg; 175 ± 4.64 cm; bench press relative strength: 1.44 ± 0.19 kg/kg of body mass) attended 4 randomly ordered sessions during which 5 consecutive sets of the bench press were performed with an absolute 3RM load and 1, 2, 3, or 5 minutes of rest interval between sets. The results indicated that significantly greater bench press repetitions were completed with 2, 3, and 5 minutes vs. 1-minute rest between sets (p ≤ 0.05); no significant differences were noted between the 2, 3, and 5 minutes rest conditions. For the 1-minute rest condition, performance reductions (relative to the first set) were observed commencing with the second set; whereas for the other conditions (2, 3, and 5 minutes rest), performance reductions were not evident until the third and fourth sets. The RPE values before each of the successive sets were significantly greater, commencing with the second set for the 1-minute vs. the 3 and 5 minutes rest conditions. Significant increases were also evident in RPE immediately after each set between the 1 and 5 minutes rest conditions from the second through fifth sets. These findings indicate that when utilizing an absolute 3RM load for the bench press, practitioners may prescribe a time-efficient minimum of 2 minutes rest between sets without significant impairments in repetition performance. However, lower perceived exertion levels may necessitate prescription of a minimum of 3 minutes rest between sets.

  16. Study of the pressing operation of large-sized tiles using X-ray absorption

    International Nuclear Information System (INIS)

    Amoros, J. L.; Mallol, G.; Llorens, D.; Boix, J.; Arnau, J. M.; Feliu, C.; Cerisuelo, J. A.; Gargallo, J. J.

    2010-01-01

    An apparatus for X-Ray non destructive inspection of bulk density distribution in large ceramic tiles has been designed, built and patented. This technique has many advantages compared with other methods: it allows tile bulk density distribution to be mapped and is neither destructive nor toxic, provided the X-ray tube and detector area are shielded to prevent leakage. In the present study, this technique, whose technical feasibility and accuracy had been verified in previous studies, has been used to scan ceramic tiles formed under different industrial conditions, modifying press working parameters. The use of high-precision laser telemeters allows tile thicknesses to be mapped, facilitating the interpretation of manufacturing defects produced in pressing, which cannot be interpreted by just measuring bulk density. The bulk density distributions obtained in the same unfired and fired tiles are also compared, a possibility afforded only by this measurement method, since it is non-destructive. The comparison of both unfired and fired tile bulk density distributions allows the influence of the pressing and firing stages on tile end porosity to be individually identified. (Author) 12 refs.

  17. Recovery of Flavonoids from Orange Press Liquor by an Integrated Membrane Process

    Directory of Open Access Journals (Sweden)

    Alfredo Cassano

    2014-08-01

    Full Text Available Orange press liquor is a by-product generated by the citrus processing industry containing huge amounts of natural phenolic compounds with recognized antioxidant activity. In this work, an integrated membrane process for the recovery of flavonoids from orange press liquors was investigated on a laboratory scale. The liquor was previously clarified by ultrafiltration (UF in selected operating conditions by using hollow fiber polysulfone membranes. Then, the clarified liquor with a total soluble solids (TSS content of 10 g·100 g−1 was pre-concentrated by nanofiltration (NF up to 32 g TSS 100 g−1 by using a polyethersulfone spiral-wound membrane. A final concentration step, up to 47 g TSS 100 g−1, was performed by using an osmotic distillation (OD apparatus equipped with polypropylene hollow fiber membranes. Suspended solids were completely removed in the UF step producing a clarified liquor containing most part of the flavonoids of the original press liquor due to the low rejection of the UF membrane towards these compounds. Flavanones and anthocyanins were highly rejected by the NF membrane, producing a permeate stream with a TSS content of 4.5 g·100 g−1. An increasing of both the flavanones and anthocyanins concentration was observed in the NF retentate by increasing the volume reduction factor (VRF. The final concentration of flavonoids by OD produced a concentrated solution of interest for nutraceutical and pharmaceutical applications.

  18. Recovery of flavonoids from orange press liquor by an integrated membrane process.

    Science.gov (United States)

    Cassano, Alfredo; Conidi, Carmela; Ruby-Figueroa, René

    2014-08-11

    Orange press liquor is a by-product generated by the citrus processing industry containing huge amounts of natural phenolic compounds with recognized antioxidant activity. In this work, an integrated membrane process for the recovery of flavonoids from orange press liquors was investigated on a laboratory scale. The liquor was previously clarified by ultrafiltration (UF) in selected operating conditions by using hollow fiber polysulfone membranes. Then, the clarified liquor with a total soluble solids (TSS) content of 10 g·100 g-1 was pre-concentrated by nanofiltration (NF) up to 32 g TSS 100 g-1 by using a polyethersulfone spiral-wound membrane. A final concentration step, up to 47 g TSS 100 g-1, was performed by using an osmotic distillation (OD) apparatus equipped with polypropylene hollow fiber membranes. Suspended solids were completely removed in the UF step producing a clarified liquor containing most part of the flavonoids of the original press liquor due to the low rejection of the UF membrane towards these compounds. Flavanones and anthocyanins were highly rejected by the NF membrane, producing a permeate stream with a TSS content of 4.5 g·100 g-1. An increasing of both the flavanones and anthocyanins concentration was observed in the NF retentate by increasing the volume reduction factor (VRF). The final concentration of flavonoids by OD produced a concentrated solution of interest for nutraceutical and pharmaceutical applications.

  19. Rest Interval Required for Power Training With Power Load in the Bench Press Throw Exercise.

    Science.gov (United States)

    Hernández Davó, Jose L; Solana, Rafael Sabido; Sarabia Marín, Jose M; Fernández Fernández, Jaime; Moya Ramón, Manuel

    2016-05-01

    This study aimed to test the influence of various rest interval (RI) durations used between sets on power output performance and physiological and perceptual variables during a strength training session using 40% of the 1 repetition maximum (1RM) in the bench press throw exercise. Thirty-one college students (18 males and 13 females) took part in the study. The experimental protocol consists of 5 sets of 8 repetitions of the bench press throw exercise with a load representing 40% of 1RM. Subjects performed the experimental protocol on 3 different occasions, differing by the RI between sets (1, 2, or 3 minutes). During the sessions, power data (mean power and peak power), physiological (lactate concentration [La]) and perceptual (rating of perceived exertion) variables were measured. In addition, delayed onset muscular soreness was reported 24 and 48 hours after the training session. One-way repeated-measures analysis of variance showed that 1-minute RI entailed higher power decreases and greater increases in values of physiological and perceptual variables compared with both 2- and 3-minute RIs. Nevertheless, no differences were found between 2- and 3-minute RIs. Therefore, this study showed that, when training with 40% of 1RM in the bench press throw exercise, a 2-minute RI between sets can be enough to avoid significant decreases in power output. Consequently, training sessions' duration could be reduced without causing excessive fatigue, allowing additional time to focus on other conditioning priorities.

  20. Importance of upper-limb inertia in calculating concentric bench press force.

    Science.gov (United States)

    Rambaud, Olivier; Rahmani, Abderrahmane; Moyen, Bernard; Bourdin, Muriel

    2008-03-01

    The purpose of this study was to investigate the influence of upper-limb inertia on the force-velocity relationship and maximal power during concentric bench press exercise. Reference peak force values (Fpeakp) measured with a force plate positioned below the bench were compared to those measured simultaneously with a kinematic device fixed on the barbell by taking (Fpeakt) or not taking (Fpeakb) upper-limb inertia into account. Thirteen men (27.8 +/- 4.1 years, 184.6 +/- 5.5 cm, 99.5 +/- 18.6 kg) performed all-out concentric bench press exercise against 8 loads ranging between 7 and 74 kg. The results showed that for each load, Fpeakb was significantly less than Fpeakp (P force (F0), maximal velocity (V0), optimal velocity (Vopt), and maximal power (Pmax), extrapolated from the force- and power-velocity relationships determined with the kinematic device, were significantly underestimated when upper-limb inertia was ignored. The results underline the importance of taking account of the total inertia of the moving system to ensure precise evaluation of upper-limb muscular characteristics in all-out concentric bench press exercise with a kinematic device. A major application of this study would be to develop precise upper-limb muscular characteristic evaluation in laboratory and field conditions by using a simple and cheap kinematic device.

  1. Brasil Mulher e Nós Mulheres: Origins of the Feminist Press in Brazil

    Directory of Open Access Journals (Sweden)

    Rosalina de Santa Cruz Leite

    2003-01-01

    Full Text Available This article presents some reflections about the feminist alternative press that appeared in the state of São Paulo, Brazil, in the second half of the 70’s. The press was a space for expression of a special breed of politics that was closely linked to the awakening of women to feminist ideas in the period after the armed struggle against the Brazilian dictatorship. The journals Brasil Mulher and Nós Mulheres portray, in their articles and editorials, the fight for amnesty, for day nurseries, for democratic freedoms – all symbols of opposition against the regime in the era of military dictatorship. In addition they report on specific matters, such as, domestic violence, women’s working-conditions, reproductive rights, abortion and sexuality. From the point of view of the popular movement and the women’s organizations, the alternative press of women is without any doubt an important source, and still under-explored, for understanding the period considered.

  2. Simulation of the Press Hardening Process and Prediction of the Final Mechanical Material Properties

    Science.gov (United States)

    Hochholdinger, Bernd; Hora, Pavel; Grass, Hannes; Lipp, Arnulf

    2011-08-01

    Press hardening is a well-established production process in the automotive industry today. The actual trend of this process technology points towards the manufacturing of parts with tailored properties. Since the knowledge of the mechanical properties of a structural part after forming and quenching is essential for the evaluation of for example the crash performance, an accurate as possible virtual assessment of the production process is more than ever necessary. In order to achieve this, the definition of reliable input parameters and boundary conditions for the thermo-mechanically coupled simulation of the process steps is required. One of the most important input parameters, especially regarding the final properties of the quenched material, is the contact heat transfer coefficient (IHTC). The CHTC depends on the effective pressure or the gap distance between part and tool. The CHTC at different contact pressures and gap distances is determined through inverse parameter identification. Furthermore a simulation strategy for the subsequent steps of the press hardening process as well as adequate modeling approaches for part and tools are discussed. For the prediction of the yield curves of the material after press hardening a phenomenological model is presented. This model requires the knowledge of the microstructure within the part. By post processing the nodal temperature history with a CCT diagram the quantitative distribution of the phase fractions martensite, bainite, ferrite and pearlite after press hardening is determined. The model itself is based on a Hockett-Sherby approach with the Hockett-Sherby parameters being defined in function of the phase fractions and a characteristic cooling rate.

  3. Inconsistent journalism: the coverage of chronic diseases in the Mexican press.

    Science.gov (United States)

    Mercado-Martinez, F J; Robles-Silva, L; Moreno-Leal, N; Franco-Almazan, C

    2001-01-01

    The mass media are recognized by many social scientists as important sources of medical information for lay people and as a positive influence on those working in the health care professions. However, there is a lack of study about print and mass media reporting on major health problems in developing countries such as Mexico. This article presents the findings of a study conducted to identify specific messages that the Mexican print media convey to the general reader about chronic diseases, especially one of the most important and pervasive, diabetes. We undertook a comprehensive review and content analysis of secondary source media reporting in the Boletin (Bulletin)--published by the Department of Education and Health, Universidad Autónoma Metropolitana, Xochimilco. The Boletin summarizes all articles related to health matters published in 12 national daily newspapers and 3 magazines. Our study covered all issues of the Boletin from 1992 through 1996. Our findings indicate that at times the press and popular print media disseminate an incomplete and often biased picture of chronic diseases prevalent in Mexico. Specifically, the press gives equal or more important coverage of acute diseases, or to AIDS, than to other major chronic conditions. The press also reproduces the biomedical model of disease and does not address topics important to certain segments of the population, including the patient. Moreover, the media may present an overly idealized impression of the capability of health services. Consequently, this failure to address the issues of certain widespread, chronic illnesses is severe enough to ask about the role of the press in medical health care reform. We conclude by suggesting areas for further research.

  4. Effects of 5 Weeks of Bench Press Training on Muscle Synergies: A Randomized Controlled Study.

    Science.gov (United States)

    Kristiansen, Mathias; Samani, Afshin; Madeleine, Pascal; Hansen, Ernst A

    2016-07-01

    Kristiansen, M, Samani, A, Madeleine, P, and Hansen, EA. Effects of 5 weeks of bench press training on muscle synergies: A randomized controlled study. J Strength Cond Res 30(7): 1948-1959, 2016-The ability to perform forceful muscle contractions has important implications in sports performance and in activities of daily living. However, there is a lack of knowledge on adaptations in intermuscular coordination after strength training. The purpose of this study was therefore to assess muscle synergies before and after 5 weeks of bench press training. Thirty untrained male subjects were randomly allocated to a training group (TRA) or a control group (CON). After the pretest, TRA completed 5 weeks of bench press training, before completing a posttest, whereas subjects in CON continued their normal life. During test sessions, surface electromyography (EMG) was recorded from 13 different muscles. Muscle synergies were extracted from EMG data using nonnegative matrix factorization. To evaluate differences between pretest and posttest, we performed a cross-correlation analysis and a cross-validation analysis, in which the synergy components extracted in the pretest session were recomputed, using the fixed synergy components from the posttest session. Two muscle synergies accounted for 90% of the total variance and reflected the concentric and eccentric phase, respectively. TRA significantly increased 3 repetition maximum in bench press with 19.0% (25th; 75th percentile, 10.3%; 21.7%) (p < 0.001), whereas no change occurred in CON. No significant differences were observed in synergy components between groups. However, decreases in correlation values for intragroup comparisons in TRA may suggest that the synergy components changed, whereas this was not the case in CON. Strength and conditioning professionals may consider monitoring changes in muscle synergies in training and rehabilitation programs as a way to benchmark changes in intermuscular coordination.

  5. Process controls for Bi2Te3-Sb2Te3 prepared by mechanical alloying and hot pressing

    International Nuclear Information System (INIS)

    Lee, Go-Eun; Kim, Il-Ho; Choi, Soon-Mok; Lim, Young-Soo; Seo, Won-Seon; Park, Jae-Soung; Yang, Seung-Ho

    2014-01-01

    p-Type Bi 2 Te 3 -Sb 2 Te 3 solid solutions were prepared by mechanical alloying (MA) and hot pressing (HP) under different process conditions, after which the transport and the thermoelectric properties were evaluated. The relative densities of all hot-pressed specimens were over 98%, and the microstructure and crystal orientation were independent of the HP direction. All specimens exhibited p-type conduction, and the electrical resistivity was observed to increase slightly with increasing temperature, indicating a degenerate semiconductor behavior. The carrier concentration decreased with increasing HP temperature while the mobility increased. The maximum figure of merit obtained was 0.86 at 323 K for Bi 0.5 Sb 1.5 Te 3 hot-pressed at 648 K.

  6. Finite element modelling and associated experimentations to optimize and predict the pressing cycle of a future AMBB manufacturing press

    International Nuclear Information System (INIS)

    Bayle, J.P.; Mezeix, P.; Tronche, E.; Delette, G.; Remy, E.; Picart, S.

    2014-01-01

    This study presents an approach based on the use of pellet forming numerical digital simulation which enables optimization of the die pressing cycle. Semi-empirical mechanical models were used in an FEM code, CAST3M. Specific powder characterizations were also performed to supply the mechanical parameters of compaction model. The methodology for the identification of five main coefficients (index flow, elastic and plastic parameters) was used with two different powders. The results show that the axial distribution of frictional forces may be changed during die pressing by a modification of the sequence of punch displacements. According to these results and the literature, the pressing cycle can be considered to have an influence on the shape of a sintered pellet through the axial distribution of green density. The process used for the identification of the Cam-Clay model coefficients seems to be in good agreement, even if the changes in certain parameters remain rather unclear and will require follow-up studies to confirm some of the results. The experimental device used produces good quality pellets, and the Radial Open Die Modulus remains the first choice for reduced pellet damage. Much work still remains to be done to fully define the identification process and create the most representative simulations possible before launching an industrial version of a nuclearized press, planned for the last quarter of year 2014. (authors)

  7. The Suburban Press; First Steps toward an Annotated Bibliography. Suburban Press Research Series No. 16 and 17.

    Science.gov (United States)

    Northern Illinois Univ., De Kalb. Suburban Press Research Center.

    This bibliography lists journal articles concerning various aspects of the suburban press. Annotated selections, arranged alphabetically according to journal title, are gathered from the following periodicals: "Advertising Age,""Business Week,""Columbia Journalism Review,""Editor and Publisher,""Grassroots Editor,""Journalism…

  8. Biomechanical analysis of press-extension technique on degenerative lumbar with disc herniation and staggered facet joint

    Directory of Open Access Journals (Sweden)

    Hong-gen Du

    2016-05-01

    Full Text Available This study investigates the effect of a new Chinese massage technique named “press-extension” on degenerative lumbar with disc herniation and facet joint dislocation, and provides a biomechanical explanation of this massage technique. Self-developed biomechanical software was used to establish a normal L1–S1 lumbar 3D FE model, which integrated the spine CT and MRI data-based anatomical structure. Then graphic technique is utilized to build a degenerative lumbar FE model with disc herniation and facet joint dislocation. According to the actual press-extension experiments, mechanic parameters are collected to set boundary condition for FE analysis. The result demonstrated that press-extension techniques bring the annuli fibrosi obvious induction effect, making the central nucleus pulposus forward close, increasing the pressure in front part. Study concludes that finite element modelling for lumbar spine is suitable for the analysis of press-extension technique impact on lumbar intervertebral disc biomechanics, to provide the basis for the disease mechanism of intervertebral disc herniation using press-extension technique.

  9. Smith machine counterbalance system affects measures of maximal bench press throw performance.

    Science.gov (United States)

    Vingren, Jakob L; Buddhadev, Harsh H; Hill, David W

    2011-07-01

    Equipment with counterbalance weight systems is commonly used for the assessment of performance in explosive resistance exercise movements, but it is not known if such systems affect performance measures. The purpose of this study was to determine the effect of using a counterbalance weight system on measures of smith machine bench press throw performance. Ten men and 14 women (mean ± SD: age, 25 ± 4 years; height, 173 ± 10 cm; weight, 77.7 ± 18.3 kg) completed maximal smith machine bench press throws under 4 different conditions (2 × 2; counterbalance × load): with or without a counterbalance weight system and using 'light' or 'moderate' net barbell loads. Performance variables (peak force, peak velocity, and peak power) were measured using a linear accelerometer attached to the barbell. The counterbalance weight system resulted in significant (p velocity (light: -0.49 ± 0.10 m·s; moderate: -0.33 ± 0.07 m·s), and peak power (light: -220 ± 43 W; moderate: -143 ± 28 W) compared with no counterbalance system for both load conditions. Load condition did not affect absolute or percentage reductions from the counterbalance weight system for any variable. In conclusion, the use of a counterbalance weight system reduces accelerometer-based performance measures for the bench press throw exercise at light and moderate loads. This reduction in measures is likely because of an increase in the external resistance during the movement, which results in a discrepancy between the manually input and the actual value for external load. A counterbalance weight system should not be used when measuring performance in explosive resistance exercises with an accelerometer.

  10. Improving Dryer and Press Efficiencies Through Combustion of Hydrocarbon Emissions

    Energy Technology Data Exchange (ETDEWEB)

    Sujit Banerjee

    2005-10-31

    Emission control devices on dryers and presses have been legislated into the industry, and are now an integral part of the drying system. These devices consume large quantities of natural gas and electricity and down-sizing or eliminating them will provide major energy savings. The principal strategy taken here focuses on developing process changes that should minimize (and in some cases eliminate) the need for controls. A second approach is to develop lower-cost control options. It has been shown in laboratory and full-scale work that Hazardous Air Pollutants (HAPs) emerge mainly at the end of the press cycle for particleboard, and, by extension, to other prod-ucts. Hence, only the air associated with this point of the cycle need be captured and treated. A model for estimating terpene emissions in the various zones of veneer dryers has been developed. This should allow the emissions to be concentrated in some zones and minimized in others, so that some of the air could be directly released without controls. Low-cost catalysts have been developed for controlling HAPs from dryers and presses. Catalysts conventionally used for regenerative catalytic oxidizers can be used at much lower temperatures for treating press emissions. Fluidized wood ash is an especially inexpensive mate-rial for efficiently reducing formaldehyde in dryer emissions. A heat transfer model for estimating pinene emissions from hot-pressing strand for the manufacture of flakeboard has been constructed from first principles and validated. The model shows that most of the emissions originate from the 1-mm layer of wood adjoining the platen surface. Hence, a simple control option is to surface a softwood mat with a layer of hardwood prior to pressing. Fines release a disproportionate large quantity of HAPs, and it has been shown both theo-retically and in full-scale work that particles smaller than 400 µm are principally responsible. Georgia-Pacific is considering green

  11. Central and Regional Official Press in Information Policy of Russian Autocracy (1901-1916

    Directory of Open Access Journals (Sweden)

    Вячеслав Вениаминович Шевцов

    2011-09-01

    Full Text Available On the basis of archival materials the author considers the activity of the governmental commissions of 1901 and 1916 on the change of rules on the publication of provincial and regional gazette. The article analyses the proposals of editors of provincial governmental newspapers and local authorities in this respect, as well as the measures undertaken by the government to increase the influence of the governmental newspapers in the conditions of the revolution of 1905-1907. The author points out the difficulties which hindered the realization of the reform of the state sector of press.

  12. An Update of Freedom of the Press and Information in Latin America and the Caribbean.

    Science.gov (United States)

    Garrison, Bruce; Munoz, Julio E.

    This paper is based on a review of the literature that included reports from the Inter-American Press Association's general assembly in Los Angeles in October 1984, the mid-year meeting of the Inter-American Press Association in Panama City in March 1985, and the 1983 world press freedom review of the International Press Institute. Other material…

  13. Effects of wet-pressing-induced fiber hornification on enzymatic saccharification of lignocelluloses

    Science.gov (United States)

    X.L. Luo; Junyong Zhu; Roland Gleisner; H.Y. Zhan

    2011-01-01

    This article reports the effect of wet-pressing-induced fiber hornification on enzymatic saccharification of lignocelluloses. A wet cellulosic substrate of bleached kraft eucalyptus pulp and two wet sulfite-pretreated lignocellulosic substrates of aspen and lodgepole pine were pressed to various moisture (solids) contents by variation of pressing pressure and pressing...

  14. Hot pressing, strength, and fracture of calcium hexaboride

    International Nuclear Information System (INIS)

    Dutta, S.K.

    1975-01-01

    Fracture behavior and strength of hot-pressed CaB 6 were studied. The modulus of elasticity determined by attaching strain gages to the tensile surface of the bend bars to measure strain, was 55 +- 3 x 10 6 psi. The results are compared with values for other low density ceramic materials (B 4 C, SiB 6 , Be 4 B, AlB 12 ) in a table. The fracture mode was observed for both modulus of rupture and impact test specimens. Predominantly transgranular fracture, associated with distinct step cleavages is evident. Fracture origins were examined in an effort to understand the strength limiting features in hot-pressed CaB 6 specimens. Surface defects, large grain agglomerations, and isolated pore pockets were observed and varied from bar to bar; these were similar to those found in B 4 C. (U.S.)

  15. Pressing Speed, Specific Pressure and Mechanical Properties of Aluminium Cast

    Directory of Open Access Journals (Sweden)

    Gaspar S.

    2016-06-01

    Full Text Available Recent research in the process of aluminum alloy die castings production, which is nowadays deeply implemented into the rapidly growing automobile, shipping and aircraft industries, is aimed at increasing the useful qualitative properties of the die casting in order to obtain its high mechanical properties at acceptable economic cost. Problem of technological factors of high pressure die casting has been a subject of worldwide research (EU, US, Japan, etc.. The final performance properties of die castings are subjected to a large number of technological factors. The main technological factors of high pressure die casting are as follows: plunger pressing speed, specific (increase pressure, mold temperature as well as alloy temperature. The contribution discusses the impact of the plunger pressing speed and specific (increase pressure on the mechanical properties of the casting aluminum alloy.

  16. Research on the Visual Processing System of the Punch Press

    Directory of Open Access Journals (Sweden)

    Sun Xuan

    2016-01-01

    Full Text Available Most of raw materials of small hardware processing for plate scraps, and it’s realized through the manual operation of ordinary punch, which way has the low production efficiency and the high labor intensity. In order to improve the automation level of production, developing and designing of a visual processing system for punch press manipulator which based on the MFC tools of Visual Studio software platform. Through the image acquisition and image processing, get the information about the board to be processed, such as shape, length, the center of gravity position and pose, and providing relevant parameters for positioning gripping and placing into the punch table positioning of the feeding manipulator and automatic programming of punching machine, so as to realize the automatic operation about press feeding and processing.

  17. Social Representations of the Environment in Press Media

    Directory of Open Access Journals (Sweden)

    Gislei Mocelin Polli

    2015-08-01

    Full Text Available Environmental issues are given prominence in the media and scientific circles. From the 60’s until early 2010 there were changes in the way people related to the environment, with a paradigm shift occurring regarding the environment. This study sought to identify the representational content disseminated by the press media on the environment in different periods. A qualitative survey was therefore conducted of documents, and data were obtained through texts published in a magazine with national circulation. The data were analyzed using the ALCESTE program with a Lexicographic Analysis. It was identified that the press media reflects the paradigm shifts, and publications dating from the late 60’s are compatible with the old paradigm, evolving over time, and are now compatible with the new environmental paradigm. The results indicate that currently the environment needs care in all its aspects and lack of care creates global impacts.

  18. News from the Library: newspapers anyone? Try PressDisplay!

    CERN Multimedia

    CERN Library

    2011-01-01

    PressDisplay is an online portal where you can browse and read online articles from more than 1,900 newspapers from 95 countries, as soon as they are published. With Pressdisplay, the time when newspapers were nicely displayed on wooden rods in libraries has passed...   Le Monde, International Herald Tribune and many more titles are displayed in their original layout including text and images, and you can print and e-mail the articles you are interested in. You even have the possibility to create rss feeds, so that the news reaches you directly.   The CERN Library has now activated a trial version of PressDisplay valid till 31 December; it is open to everyone at CERN. This trial doesn't offer the possibility to create personalised alerts based on specific search criteria. In case you need such features - or if you have any comments or questions - please contact us.

  19. Indonesian journalistic competitions: tribute or threat for press practice

    Science.gov (United States)

    Dewi, P. A. R.; Aji, G. G.; Sukardani, P. S.

    2018-01-01

    This research aims to Investigate journalists’ understanding toward glittering generalities practice - positive and good coverage of the caused by the Journalistic contests, the prices are attracting them, Reviews their motives to Participate, and their beliefs about ethics al thing. It is also retrieve how the chief editor, as a decision maker in the mass media taking his responsibility on the glittering news. This research uses a case study method by conducting indepth interviews on journalists, editors, and professional the alliance to collect the data and analyse it based on critical paradigm. The results show that journalist believe that competition is good, and there is no violation as long as the stick to the press code of conduct, but for chief editors and professional alliance, they begin to aware the damage of the contest. The findings of this work will be valuable to develop critical thinking of press workers and promote awareness to the society to control the media practice.

  20. A new cleaner process to prepare pressing-powder

    Directory of Open Access Journals (Sweden)

    Shu, Z.

    2011-10-01

    Full Text Available An alternative cleaner process of pressing-powder preparation, based on filter-pressing and a novel granulation method, is presented to substitute the existing spray-drying process. In the new process, about two-thirds of wet-milled slurry is filterpressed, dried and milled into dry fine powder. The other one-third of the slurry and the as-obtained dry fine powder are spray-mixed in a tower, where the slurry droplets adsorb the dry powder to form granules which are then rolled and dried into a useable pressing-powder for tile pressing. The key stages, filter-pressing and granulation (consisting of spray-mixing and rolling treatment, are specially studied. The pressing-powder properties and pressing/firing behavior, and, energy/water consumption and pollution emission data are presented, and a comparison between the new process and the existing spray-drying process is made. This new process has been found to be feasible and provides a pressing-powder with suitable properties, together with lower energy/water consumption and pollution emission (particulate matter and CO2.

    En ese trabajo se presenta un proceso alternativo y más ecológico para la preparación de polvo de prensas por molienda vía húmeda de las materias primas. En este proceso la eliminación del agua de la suspensión obtenida en la etapa de molienda, en vez de realizarse por secado por atomización, se lleva a cabo en dos etapas, en una primera etapa dos tercios de esta suspensión se filtro-prensan, posteriormente se secan y molturan hasta obtener un polvo seco micronizado. Este material seco se introduce por la parte superior de una torre granuladora, en la que se pulveriza el tercio de la suspensión restante por la parte inferior, de forma que las gotas adsorben sobre su superficie las partículas secas formando gránulos, que posteriormente se compactan por rodamiento (“rolling”, y finalmente se secan hasta la humedad requerida para el prensado. En

  1. Different Visions of Framing Violence in International Press News

    DEFF Research Database (Denmark)

    Ramirez, Jacobo

    in Mexico and to explore entrepreneurs’ reaction to the covered news. We also analyze journalists’ treatment of this news (Semetko & Valkendurg, 2000) and differences among newspapers from the U.S., Mexico and the European Union (EU). A sample of 200 news histories was constructed by integrating...... international and Mexican newspapers from 2006 to 2012. Our results showed that overall, U.S. and EU newspapers present more news related to violence towards entrepreneurs than Mexican outlets, which more often adopt the avoid strategy (Oliver, 1991). The conflict frame was more widely used in EU newspapers...... than in U.S. and Mexican newspapers, and the economic frame was more present in the U.S. and Mexican press than in the EU press. The morality frame was used more frequently by Mexican journalists than U.S. and European journalists. The results made it possible to observe the effects of framing...

  2. Visual impact in the digital press: a Spanish empirical research

    Directory of Open Access Journals (Sweden)

    Joan Francesc Fondevila Gascón

    2010-12-01

    Full Text Available Visual resource (photography and video inclusion in digital journalism is obtaining importance in the multimedia area. The principal resources of digital press are multimedia, hypertext and interactivity. Multimedia is in an initial process of evolution. The objective of this research is to observe empirically the use of visual resources by the digital pure player press. These media try to take advantage of the new multimedia possibilities in the development and presentation of the contents. We have analyzed empirically video and photography inclusion in the multimedia framework (text, photography, video, audio, infograph and animation programs in four digital newspapers (Libertad Digital and El Plural, in Spanish, and Vilaweb.cat and e-Noticies, in Catalan analyzed according to journalistic genres.

  3. Convicted Murderers and the Victorian Press: Condemnation vs. Sympathy

    Directory of Open Access Journals (Sweden)

    Martin J. Wiener

    2007-11-01

    Full Text Available Almost half of those receiving the death sentence in late-Victorian and Edwardian England were reprieved. The process of deciding which murderers were to hang and which were to be spared became an increasingly public one, thanks to the growing intervention of the press. This intervention grew alongside the accelerated expansion in the numbers and circulations of newspapers in the second half of the nineteenth century. As the press became a larger part of national life, its more „popular‟ and its more local segments carved out for themselves a new and ever more prominent role as major participants in public discourse over „justice‟ vs. „mercy‟ for condemned murderers. This involvement is a facet of Victorian and Edwardian newspapers that has previously been overlooked.

  4. Mediated Nationalism: Press Freedom, Mass Media, and Nationalism

    Science.gov (United States)

    2017-12-01

    spread propaganda resulted in a positive response by listeners who were predisposed to anti-Semitism and a negative response by those whose prior...2016/jun/11/ david-cameron-brexit-eu-referendum- listen -jeremy-corbyn. 5 Nations with a censored press would likely have denied the expression of...nationalism. Those “who can understand them, or can acquire such comprehension is included in a moral and economic community.”45 He states that “what is

  5. Biological effects of the ionizing radiation. Press breakfast

    International Nuclear Information System (INIS)

    Flury-Herard, A.; Boiteux, S.; Dutrillaux, B.; Toledano, M.

    2000-06-01

    This document brings together the subjects discussed during the Press breakfast of 29 june 2000 on the biological effects of the ionizing radiations, with scientists of the CEA and the CNRS. It presents the research programs and provides inquiries on the NDA operating to introduce the NDA damages by ionizing radiations, the possible repairs and the repair efficiency facing the carcinogenesis. Those researches allow the scientists to define laws on radiation protection. (A.L.B.)

  6. FREEDOM OF SPEECH IN INDONESIAN PRESS: INTERNATIONAL HUMAN RIGHTS PERSPECTIVE

    OpenAIRE

    Clara Staples

    2016-01-01

    This paper will firstly examine the International framework of human rights law and its guidelines for safeguarding the right to freedom of speech in the press. Secondly, it will describe the constitutional and other legal rights protecting freedom of speech in Indonesia and assess their compatibility with the right to freedom of speech under the International human rights law framework. Thirdly it will consider the impact of Indonesia's constitutional law and criminal and civil law, includin...

  7. Mechanical and thermophysical properties of hot-pressed SYNROC B

    International Nuclear Information System (INIS)

    Hoenig, C.L.; Newkirk, H.W.; Otto, R.A.; Brady, R.L.; Brown, A.E.; Ulrich, A.R.; Lum, R.C.

    1981-01-01

    The optimal SYNROC compositons for use with commercial waste are reviewed. Large amounts of powder (about 2.5 kg) were prepared by convention al ceramic operations to test the SYNROC concept on a processing scale. Samples, 15.2 cm in diameter, were hot pressed in graphite, and representative samples were cut for microstructural evaluations. Measured mechanical and thermophysical properties did not vary significantly as a function of sample location and were typical of titanate ceramic materials

  8. Film Advertising in the Albanian Press before World War II

    OpenAIRE

    Vjollca Hysi Panajoti; Mirdaim Axhami; Loreta Zela Axhami

    2015-01-01

    This paper aims at studying the development of film advertising in the 1930’s Albanian press. Through advertising we struggle to read a piece of the Albanian monarchy’s history. Considering advertising as a historical source tends to reflect the economic, social and cultural life of the country. The study focused on the features, characteristics and uniqueness of advertising the films in relation to other ads present in print. Who were the people who created the ads, how does the ...

  9. The Social Theories of the press: journalism and society

    Directory of Open Access Journals (Sweden)

    Beatriz Marocco

    2005-06-01

    Full Text Available For a short period of time, between the end of the 19th century and the middle of the 20th, newspapers and journalists were under the spotlight as never before. However, the comprehensive reviews of the theories of the press do not acknowledge the thought of this period and its development into “the social theories of the press” (H. Hardt, 1979. This article is positioned in this gap of press studies, and it uses as a starting point the foucaultian description of the diff erent thresholds that establish the levels of discourse elaboration (Foucault, 1995. It aims at exploring the theoretical production that approximates German and American scholars such as Albert Schäffle (1831-1903; Karl Knies (1821-1898; Karl Bücher (1847-1930; Ferdinand Tönnies (1835-1936; Albion Small (1854-1926; Edward Ross (1856-1951; Max Weber (1864-1920; Robert Park (1864-1944 and Walter Lippmann (1889-1974, rescuing this production from the pre-history of the press to materialize evidence that this production coincides, in its external origin, with the modern newspaper practices, although there seemed to be no dependence between them at the time.

  10. The Social Theories of the press: journalism and society

    Directory of Open Access Journals (Sweden)

    Beatriz Marocco

    2011-02-01

    Full Text Available For a short period of time, between the end of the 19th century and the middle of the 20th, newspapers and journalists were under the spotlight as never before. However, the comprehensive reviews of the theories of the press do not acknowledge the thought of this period and its development into “the social theories of the press” (H. Hardt, 1979. This article is positioned in this gap of press studies, and it uses as a starting point the foucaultian description of the diff erent thresholds that establish the levels of discourse elaboration (Foucault, 1995. It aims at exploring the theoretical production that approximates German and American scholars such as Albert Schäffle (1831-1903; Karl Knies (1821-1898; Karl Bücher (1847-1930; Ferdinand Tönnies (1835-1936; Albion Small (1854-1926; Edward Ross (1856-1951; Max Weber (1864-1920; Robert Park (1864-1944 and Walter Lippmann (1889-1974, rescuing this production from the pre-history of the press to materialize evidence that this production coincides, in its external origin, with the modern newspaper practices, although there seemed to be no dependence between them at the time.

  11. Graphite and boron carbide composites made by hot-pressing

    International Nuclear Information System (INIS)

    Miyazaki, K.; Hagio, T.; Kobayashi, K.

    1981-01-01

    Composites consisting of graphite and boron carbide were made by hot-pressing mixed powders of coke carbon and boron carbide. The change of relative density, mechanical strength and electrical resistivity of the composites and the X-ray parameters of coke carbon were investigated with increase of boron carbide content and hot-pressing temperature. From these experiments, it was found that boron carbide powder has a remarkable effect on sintering and graphitization of coke carbon powder above the hot-pressing temperature of 2000 0 C. At 2200 0 C, electrical resistivity of the composite and d(002) spacing of coke carbon once showed minimum values at about 5 to 10 wt% boron carbide and then increased. The strength of the composite increased with increase of boron carbide content. It was considered that some boron from boron carbide began to diffuse substitutionally into the graphite structure above 2000 0 C and densification and graphitization were promoted with the diffusion of boron. Improvements could be made to the mechanical strength, density, oxidation resistance and manufacturing methods by comparing with the properties and processes of conventional graphites. (author)

  12. Effect of instructions on EMG during the bench press in trained and untrained males.

    Science.gov (United States)

    Daniels, Rebecca J; Cook, Summer B

    2017-10-01

    Strength and rehabilitation professionals strive to emphasize certain muscles used during an exercise and it may be possible to alter muscle recruitment strategies with varying instructions. This study aimed to determine whether resistance trained and untrained males could selectively activate the pectoralis major or triceps brachii during the bench press according to various instructions. This study included 13 trained males (21.5±2.9years old, 178.7±7.0cm, 85.7±10.7kg) and 12 untrained males (20.3±1.6years old, 178.8±9.4cm, 74.6±17.3kg). Participants performed a bench press one-repetition maximum (1-RM) test, 3 uninstructed repetitions at 80% 1-RM and two more sets of three repetitions with instructions to isolate the chest or arm muscles. Electromyography (EMG) was obtained from the pectoralis major, anterior deltoid, and the long head and short head of the triceps brachii. Maximum EMG activity normalized to 1-RM for each muscle was averaged over the three repetitions for each set and compared between the uninstructed, chest-instructed and arm-instructed conditions among the groups. The trained participants had a greater 1-RM (126.2±30.6kg) than the untrained participants (61.6±14.8kg) (P0.05). When the group data was combined, short head of the triceps activity was significantly lower in the chest instruction (80.1±19.3%) when compared to the uninstructed (85.6±23.3%; P=0.01) and arm-instructed (86.0±23.2; P=0.01) conditions. It can be concluded that instructions can affect muscle activation during the bench press, and this is not dependent on training status. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Research Facility for Mechanical Press Closed Gap Adjuster

    Directory of Open Access Journals (Sweden)

    A. A. Ancifirov

    2016-01-01

    Full Text Available The article describes an example of the research facility for closed gap adjustment mechanism based on the KD2128 closed-die forging press. Its rated force with a servo drive used is 630kN. The servo drive consists of a motor with nominal power of 1.57kW and a frequency converter with power of 7.5kW, which has functions of the programmable logic controller.The article notes that such a facility is expedient and useful for practical classes on forging-andstamping machines at the BMSTU Department of «Technology processing by pressure» to demonstrate the capabilities of existing technological facility, learn a design of forging-andstamping machine units, solve the problems of automatic control, monitoring, and diagnostics in blank manufacturing.The article presents a detailed facility diagram of the closed gap adjustment mechanism and its photograph, describes the mechanism and its basic parameters, gives characteristics of the synchronous motor to drive the mechanism, reviews practical works, which the research facility may provide.Based on the four experiments the article estimates an efficiency of the research facilityuse under consideration, especially when modeling a servo motor shaft under the maximum load. The relevant diagrams confirm experimental results, namely: control current, angle of motor shaft and its speed versus time. Thus, upon the diagram analysis it can be noted that the research facility design allows providing kinematics and dynamics of the press closed gap adjuster.This article describes how to determine the closed gap adjusting accuracy of the press. Eight experiments have been conducted to evaluate a working out control signal to the linear movement of the press punch when using the research facility. It is noted that the linear positioning accuracy of the press punch reaches the hundredth parts of a millimeter of the adjustment value that is sufficient to achieve the required precision when performing operations such as

  14. Tensile and fracture toughness properties of the nanostructured oxide dispersion strengthened ferritic alloy 13Cr-1W-0.3Ti-0.3Y2O3

    International Nuclear Information System (INIS)

    Eiselt, Ch.Ch.; Klimenkov, M.; Lindau, R.; Moeslang, A.; Odette, G.R.; Yamamoto, T.; Gragg, D.

    2011-01-01

    The realization of fusion power as an attractive energy source requires advanced structural materials that can cope with ultra-severe thermo-mechanical loads and high neutron fluxes experienced by fusion power plant components, such as the first wall, divertor and blanket structures. Towards this end, two variants of a 13Cr-1W-0.3Ti-0.3Y 2 O 3 reduced activation ferritic (RAF-) ODS steel were produced by ball milling phase blended Fe-13Cr-1W, 0.3Y 2 0 3 and 0.3Ti powders in both argon and hydrogen atmospheres. The milled powders were consolidated by hot isostatic pressing (HIP). The as-HIPed alloys were then hot rolled into 6 mm plates. Microstructural, tensile and fracture toughness characterization of the hot rolled alloys are summarized here and compared to results previously reported for the as-HIPed condition.

  15. Effects of culture conditions on acetic acid production by bacteria ...

    African Journals Online (AJOL)

    SARAH

    2015-11-30

    Nov 30, 2015 ... acid under certain culture conditions similar to cocoa fermentation stress. However ... Keywords: Acetic acid bacteria, acetic acid production, Cocoa fermentation, culture conditions ..... American Society Microbiology Press, pp.

  16. Areva - Press release from the Supervisory Board; Areva - Communique de presse du Conseil de Surveillance

    Energy Technology Data Exchange (ETDEWEB)

    Marie, Patricia; Briand, Pauline; Floquet-Daubigeon, Fleur; Michaut, Maxime; Scorbiac, Marie de; Repaire, Philippine du

    2012-02-14

    During its meeting held on December 12, 2011, devoted in particular to the examination of the 2011 closing estimates, the AREVA Executive Board indicated that it expected to book a provision of 1.46 billion euros (2.025 billion US dollars) in the company's accounts for fiscal year 2011 for impairment of assets for the reporting entity UraMin, a mining company acquired by AREVA in 2007, which, given the provision booked in 2010 (426 million euros), brings the value of these assets on the AREVA balance sheet down to 410 million euros. Given the size of these provisions, the Supervisory Board decided to make three of its members, meeting as an ad hoc committee, in charge of analyzing the terms of acquisition of this company, as well as the key decisions made in this reporting entity up to 2011 and, based on the outcome of these analyses, to recommend to it any appropriate measures in AREVA's interest. This committee reported on its work during the Supervisory Board meeting held on February 14, 2012. In light of this report, the Supervisory Board found that the fairness and reliability of the financial statements of previous years were not in question. Nevertheless, considering the malfunctions raised, the Board considers it appropriate to thoroughly review AREVA's governance in order to ensure that decisions concerning large acquisitions or investments be reviewed and validated in the future under conditions ensuring better legal and financial security and enabling a more transparent dialogue between management and the Supervisory Board. It thus asked the Executive Board to recommend, at the next General Meeting of Shareholders, that the by-laws of the company be modified to make the Supervisory Board's prior approval of investments, stake acquisitions and acquisitions mandatory above a threshold of 20 million euros. It also decided to set up a business ethics committee within the Supervisory Board responsible for ensuring that rules of conduct are

  17. The antimatter. Press breakfast 23 may 2000; L'antimatiere. Petit dejeuner de presse 23 mai 2000

    Energy Technology Data Exchange (ETDEWEB)

    Spiro, M; Dejardin, M; Debu, P; Aleksan, R [CEA/Saclay, Dept. d' Astrophysique, de la Physique des Particules, de la Physique Nucleaire et de l' Instrumentation Associee (DAPNIA), 91 - Gif-sur-Yvette (France)

    2000-05-01

    This document brings together the subjects discussed during the Press breakfast of 23 may 2000 on the antimatter, with scientists of the CEA and the CNRS. It presents the research programs and the experiments on the antimatter and the symmetry violation: the CP LEAR and the NA48 experiments at CERN, the BaBar detector at SLAC, the fundamental research at the CEA and the impacts on the energy policy. It provides also links for more detailed inquiries. (A.L.B.)

  18. Biological effects of the ionizing radiation. Press breakfast; Effets biologiques des rayonnements ionisants. Petit dejeuner de presse

    Energy Technology Data Exchange (ETDEWEB)

    Flury-Herard, A [CEA, Direction des Sciences du Vivant, DSV, 75 - Paris (France); Boiteux, S; Dutrillaux, B [CEA/Fontenay-aux-Roses, Direction des Sciences du Vivant, DSV, 92 (France); Toledano, M [CEA Saclay, Direction des Sciences du Vivant, DSV, 91 - Gif-sur-Yvette (France)

    2000-06-01

    This document brings together the subjects discussed during the Press breakfast of 29 june 2000 on the biological effects of the ionizing radiations, with scientists of the CEA and the CNRS. It presents the research programs and provides inquiries on the NDA operating to introduce the NDA damages by ionizing radiations, the possible repairs and the repair efficiency facing the carcinogenesis. Those researches allow the scientists to define laws on radiation protection. (A.L.B.)

  19. Effect of roll hot press temperature on crystallite size of PVDF film

    Energy Technology Data Exchange (ETDEWEB)

    Hartono, Ambran, E-mail: ambranhartono@yahoo.com; Sanjaya, Edi [Departement of Physics Faculty of Science and Technology, Islamic State University Syarif Hidayatullah , Jl. Juanda 95 Ciputat Jakarta (Indonesia); Djamal, Mitra; Satira, Suparno; Bahar, Herman [Theoretical High Energy Physics and Instrumentation Group Research, Faculty Mathematics and Natural Sciences, Institut Teknologi Bandung, Jl. Ganesa 10 Bandung (Indonesia); Ramli [Departement of Physics, Faculty of Mathematics and Natural Sciences, Universitas Negeri Padang, Jl.Prof. Hamka, Padang 25131 (Indonesia)

    2014-03-24

    Fabrication PVDF films have been made using Hot Roll Press. Preparation of samples carried out for nine different temperatures. This condition is carried out to see the effect of Roll Hot Press temperature on the size of the crystallite of PVDF films. To obtain the diffraction pattern of sample characterization is performed using X-Ray Diffraction. Furthermore, from the diffraction pattern is obtained, the calculation to determine the crystallite size of the sample by using the Scherrer equation. From the experimental results and the calculation of crystallite sizes obtained for the samples with temperature 130 °C up to 170 °C respectively increased from 7.2 nm up to 20.54 nm. These results show that increasing temperatures will also increase the size of the crystallite of the sample. This happens because with the increasing temperature causes the higher the degree of crystallization of PVDF film sample is formed, so that the crystallite size also increases. This condition indicates that the specific volume or size of the crystals depends on the magnitude of the temperature as it has been studied by Nakagawa.

  20. Results and problems in the development of machines employed in pressing technology

    Energy Technology Data Exchange (ETDEWEB)

    Dietrich, P; Hinne, H; Linke, L; Nerger, R

    1980-08-01

    Features specifications and technical improvements of nine GDR made briquetting presses from the Zemag Zeitz company. Briquetting presses have been produced by the company for more than 100 years, the present capacity of the machines ranges from 5.1 t/h to 20.4 t/h of nominal briquet production. Development trends are directed toward larger presses. The prototype PSA 400, based on the design of the four channel press PSA 300, will be tested in industrial operation during 1980/81. Various technical details on the general briquetting press design are enumerated, including experiences gained with steam or electric power operated presses, regulation of the pressing speed with a patented switch gear system, maintenance of crank gear bearings, greasing of steam driven presses, investigation of crack damages to the machine block, further measures for reducing wear of the pressing channel and mechanized welding methods for the channel overhaul. (In German)

  1. Application of exopolysaccharides to improve the performance of ceramic bodies in the unidirectional dry pressing process

    Science.gov (United States)

    Caneira, Inês; Machado-Moreira, Bernardino; Dionísio, Amélia; Godinho, Vasco; Neves, Orquídia; Dias, Diamantino; Saiz-Jimenez, Cesareo; Miller, Ana Z.

    2015-04-01

    Ceramic industry represents an important sector of economic activity in the European countries and involves complex and numerous manufacturing processes. The unidirectional dry pressing process includes milling and stirring of raw materials (mainly clay and talc minerals) in aqueous suspensions, followed by spray drying to remove excess water obtaining spray-dried powders further subjected to dry pressing process (conformation). However, spray-dried ceramic powders exhibit an important variability in their performance when subjected to the dry pressing process, particularly in the adhesion to the mold and mechanical strength, affecting the quality of the final conformed ceramic products. Therefore, several synthetic additives (deflocculants, antifoams, binders, lubricants and plasticizers) are introduced in the ceramic slips to achieve uniform and homogeneous pastes, conditioning their rheological properties. However, an important variability associated with the performance of the conformed products is still reported. Exopolysaccharides or Extracellular Polymeric Substances (EPS) are polymers excreted by living organisms, such as bacteria, fungi and algae, which may confer unique and potentially interesting properties with potential industrial uses, such as viscosity control, gelation, and flocculation. Polysaccharides, such as pullulan, gellan, carrageenan and xanthan have found a wide range of applications in food, pharmaceutical, petroleum, and in other industries. The aim of this study was the assessment of exopolysaccharides as natural additives to optimize the performance of spray-dried ceramic powders during the unidirectional dry pressing process, replacing the synthetic additives used in the ceramic production process. Six exopolysaccharides, namely pullulan, gellan, xanthan gum, κappa- and iota-carrageenan, and guar gum were tested in steatite-based spray-dried ceramic powders at different concentrations. Subsequently, these ceramic powders were

  2. Microstructural and mechanical characteristics of EUROFER'97 processed by equal channel angular pressing

    International Nuclear Information System (INIS)

    Fernandez, P.; Eddahbi, M.; Auger, M.A.; Leguey, T.; Monge, M.A.; Pareja, R.

    2011-01-01

    EUROFER'97 was processed by equal channel angular pressing (ECAP) at 823 K for a total of 4 or 8 passes, using a die angle of 105 o , and its microstructure and tensile behavior in temperature range 568-873 K investigated. A single ECAP pass developed a deformation texture {1 1 0} that was practically stable during subsequent ECAP passes. The materials processed by 1 or 2 passes exhibited a fine microstructure of recovered subgrains and tensile behavior very similar to that for the tempered material in the as-received condition. The materials processed using 4 or 8 passes exhibited nearly equiaxial submicron grained structures with a high density of high-angle grain boundaries. These materials became softer than the as-received material at a testing temperature of ∼823 K. EUROFER ECAP processed under the present conditions exhibited hardening ratio somewhat higher than that of the as-received material.

  3. Mechanical Properties of Copper Processed by Equal Channel Angular Pressing

    Science.gov (United States)

    Sülleiová, K.; Ballóková, B.; Besterci, M.; Kvačkaj, T.

    2017-12-01

    The development of the nanostructure in commercial pure copper and the strength and ductility after severe plastic deformation (SPD) with the technology of equal channel angular pressing (ECAP) are analysed. Experimental results and analyses showed that both strength and ductility can be increased simultaneously by SPD. The final grain size decreased from the initial 50μm by SPD to 100-300 nm after 10 passes. An increase of the ductility together with an increase of strength caused by SPD are explained by a strong grain refinement and by a dynamic equilibrium of weakening and strengthening, and it is visible on the final static tensile test stress-strain charts.

  4. NIC (Nuclear Industry in China) exhibition. Press file

    International Nuclear Information System (INIS)

    1998-01-01

    Framatome participated to the NIC exhibition which took place in Beijing (China) on March 1998. This press dossier was distributed to visitors. It presents in a first part the activities of the Framatome group in people's republic of China (new constructions (Daya Bay, Ling Ao project), technological cooperation and contracts in the nuclear domain, technology transfers in the domain of nuclear fuels, activities and daughter companies in the domain of industrial equipments, Framatome Connectors International (FCI) daughter company in the domain of connectors engineering). Then, the general activities of Framatome in the nuclear, industrial equipment, and connectors engineering domains are summarized in the next 3 parts. (J.S.)

  5. The pressing energy innovation challenge of the US National Laboratories

    Science.gov (United States)

    Anadon, Laura Diaz; Chan, Gabriel; Bin-Nun, Amitai Y.; Narayanamurti, Venkatesh

    2016-10-01

    Accelerating the development and deployment of energy technologies is a pressing challenge. Doing so will require policy reform that improves the efficacy of public research organizations and strengthens the links between public and private innovators. With their US$14 billion annual budget and unique mandates, the US National Laboratories have the potential to critically advance energy innovation, yet reviews of their performance find several areas of weak organizational design. Here, we discuss the challenges the National Laboratories face in engaging the private sector, increasing their contributions to transformative research, and developing culture and management practices to better support innovation. We also offer recommendations for how policymakers can address these challenges.

  6. Press Manipulation and Its Negative Impact on the Youth

    Directory of Open Access Journals (Sweden)

    Ioana Manea

    2010-12-01

    Full Text Available Nowadays, manipulation may be regarded as an essential instrument of the “mass industrial society”, aiming at the conclusion of certain agreements that are convenient to the issuing party, turning to deceit with falsified arguments, as well as to appeals to emotional or non-rational components. The particular forms that it takes in various fields of social life may be found anywhere, from the political form to the economic one. Press strategies have the capacity of manipulating the young consumer’s behaviour, generating numerous negative effects on their everyday life.

  7. Clay characterization for making pressed and burned blocks

    International Nuclear Information System (INIS)

    Alexandre, J.; Silva, C.L. de A.P. e

    2012-01-01

    The municipality of Campos dos Goytacazes, located in the state of Rio de Janeiro, at 275 km from the capital, are the largest industrial ceramic state and he has over 100 unionized industries. The production of these industries is based on tiles, building blocks and bricks. Seeking the improvement and diversification of production, the North Fluminense State University has 18 years working in partnership with local industry, with students and teachers. One of the researches is the production of blocks pressed and burned. In this work are presented in many lab tests performed, morphology and some of technological properties. (author)

  8. [Cigarette and alcohol advertising in the Swiss free press].

    Science.gov (United States)

    Olivier, Jacques

    2014-11-26

    Tobacco and alcohol are ordinary consumer goods that are still two overriding preventable causes of death in Switzerland. Massive advertising supports their selling and contributes to maintain a major public health problem up to date. The widely read free press represents an interesting advertising mean. The study of tobacco and alcohol advertisements published in the free newspaper 20 minutes through the year 2012 gives us a good idea of these products' advertising strategies. Compared to those for alcohol, the cigarette advertisements are more numerous, more suggestive and dealing with emotions. The themes proposed respond to young people's expectations in order to incline them to smoke, whereas positive images encourage to keep on smoking.

  9. Hot pressing of uranium nitride and mixed uranium plutonium nitride

    International Nuclear Information System (INIS)

    Chang, J.Y.

    1975-01-01

    The hot pressing characteristics of uranium nitride and mixed uranium plutonium nitride were studied. The utilization of computer programs together with the experimental technique developed in the present study may serve as a useful purpose of prediction and fabrication of advanced reactor fuel and other high temperature ceramic materials for the future. The densification of nitrides follow closely with a plastic flow theory expressed as: d rho/ dt = A/T(t) (1-rho) [1/1-(1-rho)/sup 2/3/ + B1n (1-rho)] The coefficients, A and B, were obtained from experiment and computer curve fitting. (8 figures) (U.S.)

  10. STS-114: Discovery Crew Post Landing Press Briefing

    Science.gov (United States)

    2005-01-01

    The crew of the STS-114 Discovery is shown during a post landing press briefing. Commander Collins introduces the crew members who consist of Pilot Jim Kelley, Mission Specialist Soichi Noguchi from JAXA, Steve Robinson, Mission Specialist and Charlie Camarda, Mission Specialist. Steve Robinson answers a question from the news media about the repair that he performed in orbit, and his feelings about being back in his hometown of California. Commander Collins talks about the most significant accomplishment of the mission. The briefing ends as each crewmember reflects on the Space Shuttle Columbia tragedy and expresses their personal thoughts and feelings as they re-entered the Earth's atmosphere.

  11. Tribologic analysis and technical innovation for rotary molding press

    International Nuclear Information System (INIS)

    Luo Wei; Bai Yumeng; Dai Xingjian

    2012-01-01

    The rotary molding press R53C-Y is the key facility in the compression molding working procedure of the nu clear fuel pellets. Its main compression assembly called the upper compression roller frame has been worn seriously during the production. At first, the mechanical model of the upper compression roller assembly was established for analysis and calculation physical strength. Then the wear causations of the upper compression roller frame were analyzed, and the existent problems of central lubrication system were discussed. Finally, Oil-air central lubrication system was designed considering the characteristic of nuclear fuel pellets production. (authors)

  12. Kustomoitu responsiivinen WordPress-sivusto suomalaiselle Toisenlainen-elokuvalle

    OpenAIRE

    Räsänen, Kati

    2016-01-01

    Opinnäytetyö kertoo Toisenlainen-nimiselle suomalaiselle elokuvalle toteutetusta verkkosivuprojektista. Sivuston pohjana käytettiin WordPress-sisällönhallintajärjestelmää ja sivuston teossa huomioitiin sen skaalautuvuus sekä käytettävyys eri päätelaitteilla. Tutkimusraportissa käsitellään myös tarkemmin responsiivista verkkosivukehitystä sekä sitä, millaisia uusia ajatus- ja toimintamalleja se verkkosivujen tekijöiltä vaatii. Lisäksi raportissa käydään läpi responsiiviseen kehitykseen lii...

  13. 'Combating' tropical diseases in the German colonial press.

    Science.gov (United States)

    Correa, Sílvio Marcus de Souza

    2013-03-01

    This article shows how much certain German language newspapers were a vehicule for reporting to the lay public on 'combating' tropical diseases. Through the press, immigrants and their descendents in Brazil were informed not only about the diseases which afflicted German colonists in Africa, but also about measures concerning sanitation, prophylaxis and experiments with tropical medicine, etc. Based on hemerographic sources, it shows how successful the overseas German communities were in sharing their experiences regarding health in tropical and/or sub-tropical regions.

  14. FILMING OF 'CONTACT' AT LC39 PRESS SITE

    Science.gov (United States)

    1997-01-01

    Warner Bros.' cast and crew are filming scenes for the movie 'Contact' at Kennedy Space Center's Launch Complex 39 Press Site on January 30. The screenplay for 'Contact' is based on the best- selling novel by the late astronomer Carl Sagan. The cast includes Jodie Foster, Matthew McConaughey, John Hurt, James Woods, Tom Skerritt, David Morse, William Fichtner, Rob Lowe and Angela Bassett. Described by Warner Bros. as a science fiction drama, 'Contact' will depict humankind's first encounter with evidence of extraterrestrial life.

  15. Effect of hot isostatic pressing temperature on the microstructural and mechanical properties in the mullite-zirconia composites

    International Nuclear Information System (INIS)

    Greca, M.C.G.; Melo, M. de F.

    1990-01-01

    This work studies the densification, the microstrutural evolution (porosity and zirconia grain size) and bending strength (σ f ) of the two mullite-zirconia composites with TiO 2 additions (0.25 and 1,0 mole%) submitted to different kind of hipping cycles at several temperatures. The results have been shown that: i) HIPing temperature seem to have no influence in densification and mechanical behaviour. ii) Total densification only appears in composition with more quantity of titania (1.0 mole%) which prove that titanium enhance the mass transfer by changes in grain boundary microchemistry. iii) Mechanical behaviour is correlated with densification and microstructural evolution for both composites and degradation is present at 1500 0 C and 1550 0 C which is related with particle coarsening. (author) [pt

  16. Effect of seed quality on oxidative stability of cold-pressed sunflower oil

    Directory of Open Access Journals (Sweden)

    Dimić Etelka B.

    2015-01-01

    Full Text Available The objective of this study was to investigate the impact of the storage time, content of the husk and impurities in the seed mass on the oxidative stability of the cold pressed sunflower oil. The oxidative stability of oil was analyzed by the RSM (Response Surface Methodology, where the response value (output of the model was the content of oxidation products measured via specific absorbance at 232 nm for conjugated dienes and 270 nm for conjugated trienes. Analyses were performed on the fresh oil samples and oil samples tempered under the Schaal-Oven’s test conditions (96 h at 63±2ºC. It was concluded that the seed storage time had significant impact on the primary (A1%232nm and secondary (A1%270nm oil oxidation products, both before (b1-p<0,001; b1-p=0,021 and after (b1-p=0,048; b1-p=0,033 the heating of oil. The content of impurities and husks in the seeds used for pressing also had an influence of the conjugated dienes and trienes contents in both, fresh and heated oil samples. However, their impact was not statistically significant. Interaction of seed storage time, the content of impurities and husks also exert some effect on the values of these quality parameters in the fresh oil as well as in the oil after the heat treatment, even though their influence is not significant. The obtained results have shown that the cold pressed sunflower oil had a good oxidative stability at temperatures up to 63±2ºC.

  17. Anaerobic co-digestion of sugarcane press mud with vinasse on methane yield.

    Science.gov (United States)

    López González, Lisbet Mailin; Pereda Reyes, Ileana; Romero Romero, Osvaldo

    2017-10-01

    The conversion efficiency of high solids waste digestion as sugarcane press mud (P) may be limited due to hydrolysis step. The option of co-digestion with vinasse, main liquid waste generated from ethanol production, was investigated under batch regime at mesophilic conditions (37.5±1°C) and the best mixture was evaluated under semicontinuous regime in stirred-tank reactors. The maximum values for methane yield in batch tests were for V 75 /P 25 and V 50 /P 50 mixtures (on basis of the chemical oxygen demand (COD) percentage added in the mixture), with an average value of 246NmL CH 4 g -1 COD fed , which was 13% higher than that of press mud alone. A highest methane production rate of 69.6NmL CH 4 g -1 COD fed -1 d -1 was obtained for the mixtureV 75 /P 25 . During the experiment carried out in CSTR reactors, the organic loading rate (OLR) was increased from 0.5 up to 2.2gVSL -1 d -1 . Methane yields of 365L CH 4 kg -1 VS and biogas productivities of 1.6LL -1 were obtained in co-digestion, which was 64% higher in comparison to mono-digestion. The performance of the process in mono-digestion was less stable than in co-digestion, with a significant fall of methane yield to 1.8kgVSm -3 d -1 , and a partial inhibition of the methanogenic archaeas when the OLR was increased up to 2.2kgVSm -3 d -1 . The co-digestion of vinasse with press mud is a good option for the treatment of streams at the alcohol-sugar industry. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Climate change and daily press : Italy vs Usa parallel analysis

    International Nuclear Information System (INIS)

    Borrelli, G.; Mazzotta, V.; Falconi, C.; Grossi, R.; Farabollini, F.

    1996-06-01

    Among ENEA (Italian National Agency for New Technologies, Energy, and the Environment) activities, one deals with analysis and strategies of environmental information. A survey of four daily newspaper coverage, on an issue (Global Climate Change) belonging to this area, has been realized. The involved newspapers are: two Italian ones, namely 'La Repubblica' and 'Il Corriere della Sera', two North-American ones, namely 'New York Times' and 'Washington Post'. Purpose of the work was that of detecting the qualitative and quantitative level of consciousness of the Italian press via a comparison with the North-American press, notoriously sensible and careful on environmental issues. The number of articled analyzed is partitioned in the following numerical data: 319 for the 'New York Times', 309 for the 'Washington Post', 146 for the 'Corriere della Sera', 81 articles for 'La Repubblica'. The time period covered for the analysis spans from 1989, initiatic year for the organization of the 1992 Rio Conference, to December 1994, deadline date for the submission of national

  19. Diachronic changes in word probability distributions in daily press

    Directory of Open Access Journals (Sweden)

    Stanković Jelena

    2006-01-01

    Full Text Available Changes in probability distributions of individual words and word types were investigated within two samples of daily press in the span of fifty years. Two samples of daily press were used in this study. The one derived from the Corpus of Serbian Language (CSL /Kostić, Đ., 2001/ that covers period between 1945. and 1957. and the other derived from the Ebart Media Documentation (EBR that was complied from seven daily news and five weekly magazines from 2002. and 2003. Each sample consisted of about 1 million words. The obtained results indicate that nouns and adjectives were more frequent in the CSL, while verbs and prepositions are more frequent in the EBR sample, suggesting a decrease of sentence length in the last five decades. Conspicuous changes in probability distribution of individual words were observed for nouns and adjectives, while minimal or no changes were observed for verbs and prepositions. Such an outcome suggests that nouns and adjectives are most susceptible to diachronic changes, while verbs and prepositions appear to be resistant to such changes.

  20. Gender violence news in British and American press

    Directory of Open Access Journals (Sweden)

    Sara Bustinduy

    2016-03-01

    Full Text Available This study aims to prove which qualities, from the British and United States actual press, are more adequate for gender violence issues, comparing news on the same stories. It is evident the influence of mass media on public opinion and, therefore, the responsibility that written press has on gender violence messages, avoiding sensationalism. Psycholinguistic studies have established the relation language-thought, so language used in journalism is crucial. Following the belief that newspapers considered more liberal and independent will lead to a better treatment than traditional ones considered to be more reluctant to change, journals have been selected. Furthermore, different cultures can be as objective and respectful but maybe less committed with the issue, as it may arise from the samples. There have been emerging ethic codes giving guidelines to journalists, including discrimination, and more specific on gender sensitive reporting. Therefore, the objective to improve public opinion information, stepping away from stereotypes and oversimplifications, is substantial, and will undoubtedly result in a better understanding of equality.

  1. Kennedy Space Center Press Site (SWMU 074) Interim Measure Report

    Science.gov (United States)

    Applegate, Joseph L.

    2015-01-01

    This report summarizes the Interim Measure (IM) activities conducted at the Kennedy Space Center (KSC) Press Site ("the Press Site"). This facility has been designated as Solid Waste Management Unit 074 under KSC's Resource Conservation and Recovery Act Corrective Action program. The activities were completed as part of the Vehicle Assembly Building (VAB) Area Land Use Controls Implementation Plan (LUCIP) Elimination Project. The purpose of the VAB Area LUCIP Elimination Project was to delineate and remove soil affected with constituents of concern (COCs) that historically resulted in Land Use Controls (LUCs). The goal of the project was to eliminate the LUCs on soil. LUCs for groundwater were not addressed as part of the project and are not discussed in this report. This report is intended to meet the Florida Department of Environmental Protection (FDEP) Corrective Action Management Plan requirement as part of the KSC Hazardous and Solid Waste Amendments permit and the U.S. Environmental Protection Agency's (USEPA's) Toxic Substance Control Act (TSCA) self-implementing polychlorinated biphenyl (PCB) cleanup requirements of 40 Code of Federal Regulations (CFR) 761.61(a).

  2. Muscle synergies during bench press are reliable across days.

    Science.gov (United States)

    Kristiansen, Mathias; Samani, Afshin; Madeleine, Pascal; Hansen, Ernst Albin

    2016-10-01

    Muscle synergies have been investigated during different types of human movement using nonnegative matrix factorization. However, there are not any reports available on the reliability of the method. To evaluate between-day reliability, 21 subjects performed bench press, in two test sessions separated by approximately 7days. The movement consisted of 3 sets of 8 repetitions at 60% of the three repetition maximum in bench press. Muscle synergies were extracted from electromyography data of 13 muscles, using nonnegative matrix factorization. To evaluate between-day reliability, we performed a cross-correlation analysis and a cross-validation analysis, in which the synergy components extracted in the first test session were recomputed, using the fixed synergy components from the second test session. Two muscle synergies accounted for >90% of the total variance, and reflected the concentric and eccentric phase, respectively. The cross-correlation values were strong to very strong (r-values between 0.58 and 0.89), while the cross-validation values ranged from substantial to almost perfect (ICC3, 1 values between 0.70 and 0.95). The present findings revealed that the same general structure of the muscle synergies was present across days and the extraction of muscle synergies is thus deemed reliable. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Means of temporal expressions in newspaper news and press report

    Directory of Open Access Journals (Sweden)

    Čutura Ilijana R.

    2016-01-01

    Full Text Available This paper analyses most frequent linguistic means for expressing the temporal frame in the printed news and press reports. With structuralism as a chosen theoretical framework, the approach of the research is qualitative and stylistic. Since the study belongs to the field of functional stylistics, the primary methods used in the study were functional-stylistic and linguistic-stylistic ones. As the study focuses on two newspaper genres, comparative-stylistic method was used as well. The analysis has been conducted on concrete linguistic excerpts from Serbian daily newspapers published throughout Serbia from 2008 to 2015. The aims of the paper are to show model of expressing temporal frame in contemporary Serbian newspapers. This paper provides an overview of the characteristics of model and the types of temporal expression as well as their variations in contemporal Serbian newspapers. The paper also aims to determine the differencies between printed news and press reports by the choice of temporal expressions. It is shown that there is a tendency of changing schematized structure of these informative genres and some innovation in relation to the choice of linguistic means for expessing the meaning of temporally close events. The research is a contribution to journalism stylistics, more precisely to the Serbian language newspaper stylistics, and also contributes to the study of linguistic and stylistic characteristics of non-literary texts. The study is also relevant because it describes the use of adverbs and adverbial expressions in the journalistic style.

  4. Feasibility of tailoring of press formed thermoplastic composite parts

    Science.gov (United States)

    Sinke, J.

    2018-05-01

    The Tailor Made Blank concept is widely accepted in the production of sheet metal parts. By joining, adding and subtracting materials, and sometimes even applying different alloys, parts can be produced more efficiently by cost and/or weight, and new design options have been discovered. This paper is about the manufacture of press formed parts of Fibre Reinforced Thermoplastics and the evaluation whether the Tailoring concept, though adapted to the material behavior of FRTP, can be applied to these composites as well. From research, the first results and ideas are presented. One of the ideas is the multistep forming process, creating parts with thickness variations and combinations of fibre orientations that are usually not feasible using common press forming strategies. Another idea is the blending of different prepreg materials in one component. This might be useful in case of specific details, like for areas of mechanical fastening or to avoid carbon/metal contact, otherwise resulting in severe corrosion. In a brief overview, future perspectives of the potential of the Tailoring concept are presented.

  5. Precision Force Control for an Electro-Hydraulic Press Machine

    Directory of Open Access Journals (Sweden)

    Hong-Ming Chen

    2014-08-01

    Full Text Available This thesis is primarily intended to design a PC-based control system to control the force of an electro-hydraulic servo press system for implementing precision force control. The main feature is to develop a composite control by using the relief valve and the flow servo valve. Using feedback from a force sensor, a fuzzy controller was designed with LabVIEW software as the system control core for achieving a precision force control for the hydraulic cylinder on its travel and output. The weakness of hydraulic systems is that hydraulic oil is compressible and prone to leaking, and its characteristics can vary with oil temperature, thus making it difficult for a general linear controller to achieve accurate control. Therefore, a fuzzy controller was designed with LabVIEW along with a NI-PCI_6221 interface card and a load cell to control the servo valve flow and the relief valve to control the pressure source. The testing results indicate that accurate force control output of an electro-hydraulic servo press system can be obtained.

  6. Human Rights and Consership in the Portuguese Press

    Directory of Open Access Journals (Sweden)

    Isabel Salema Morgado

    2007-06-01

    Full Text Available This article analyzes the censorship system existing in Portugal in the XVIII century, when a rigid jurisdiction with respect to press freedom was instituted by Portuguese State and how “Gazeta de Lisboa” succeeded in informing its public about the revolutionary events that took place in France during the year of 1789. Many years after that, in 1948, other important event – the Universal Declaration of Human Rights approved by the United Nations General Assembly, did not receive the attention of Portuguese Press. Of the 15 newspapers and magazines with wider circulation that were consulted, only three published the news of the approval. Also I did not fi nd in any of the archives documents which proved the exercising of censorship or punishment, by the dictatorial regime of Salazar, in the form of disciplinary processes against the newspapers with relation to the publication of news referring to the Declaration. I am inclined toward the theory of the act of self-censorship imposed by the editor on himself, in both events.

  7. LSA glass-ceramic tiles made by powder pressing

    International Nuclear Information System (INIS)

    Figueira, F.C.; Bertan, F.M.; Riella, H.G.; Uggioni, E.; Bernardin, A.M.

    2009-01-01

    A low cost alternative for the production of glass-ceramic materials is the pressing of the matrix glass powders and its consolidation simultaneously with crystallization in a single stage of sintering. The main objective of this work was to obtain LSA glass ceramics with low thermal expansion, processed by pressing and sintering a ceramic frit powder. The raw materials were homogenized and melted (1480 deg C, 80min), and the melt was poured in water. The glass was chemically (XRF and AAS) and thermally (DTA, 10 deg C/min, air) characterized, and then ground (60min and 120min). The ground powders were characterized (laser diffraction) and compressed (35MPa and 45MPa), thus forming four systems. The compacts were dried (150 deg C, 24h) and sintered (1175 deg C and 1185 deg C, 10 deg C/min). Finally, the glass-ceramics were characterized by microstructural analysis (SEM and XRD), mechanical behavior (σbending) and thermal analysis (α). The best results for thermal expansion were those for the glass-ceramics processed with smaller particle size and greater compaction pressure. (author)

  8. Bench press and push-up at comparable levels of muscle activity results in similar strength gains.

    Science.gov (United States)

    Calatayud, Joaquin; Borreani, Sebastien; Colado, Juan C; Martin, Fernando; Tella, Victor; Andersen, Lars L

    2015-01-01

    Electromyography (EMG) exercise evaluation is commonly used to measure the intensity of muscle contraction. Although researchers assume that biomechanically comparable resistance exercises with similar high EMG levels will produce similar strength gains over the long term, no studies have actually corroborated this hypothesis. This study evaluated EMG levels during 6 repetition maximum (6RM) bench press and push-up, and subsequently performed a 5-week training period where subjects were randomly divided into 3 groups (i.e., 6RM bench press group, 6RM elastic band push-up group, or control group) to evaluate muscle strength gains. Thirty university students with advanced resistance training experience participated in the 2-part study. During the training period, exercises were performed using the same loads and variables that were used during the EMG data collection. At baseline, EMG amplitude showed no significant difference between 6RM bench press and band push-up. Significant differences among the groups were found for percent change (Δ) between pretest and posttest for 6RM (p = 0.017) and for 1 repetition maximum (1RM) (p bench press group and 6RM elastic band push-up group improved their 1RM and 6RM (Δ ranging from 13.65 to 22.21) tests significantly with similar gains, whereas control group remains unchanged. Thus, when the EMG values are comparable and the same conditions are reproduced, the aforementioned exercises can provide similar muscle strength gains.

  9. Veulent-ils encore une carte de presse ? Les jeunes journalistes de Belgique francophone

    Directory of Open Access Journals (Sweden)

    Olivier Standaert

    2013-12-01

    Full Text Available Cet article questionne les formes identitaires développées par les jeunes journalistesbelges lorsque se pose à eux la question de la possession de la carte de presse. La méthodologie s’appuie sur une étude descriptive du profil professionnel des jeunes journalistes et sur des entretiens non directifs menés auprès de journalistes, encartés ou non, ayant moins de cinq ans d’ancienneté. Il apparaît qu’une part importante d’entre eux ne répond plus, et ce durant une période de plus en plus longue, aux critères stricts d’obtention de la carte de presse tels que définis par les autorités belges. La carte de presse est par conséquent souvent sollicitée après l’insertion effective sur le marché du travail. Ceci peut s’expliquer par la précarisation des conditions d’insertion dans le groupe professionnel des journalistes. La montée de la précarisation au sein des médias d’information générale est une des hypothèses explicatives du décalage fréquemment constaté entre les formes identitaires traditionnelles, attachées à la carte de presse, et celles des jeunes journalistes, dominées par la figure de l’individu précaire, flexible et substituable en dépit d’une vocation affichée. Les entretiens mettent cependant en évidence un discours ambivalent où une rhétorique d’indifférence, de questionnement, voire de rejet par rapport à tout document se donnant un pouvoir d’authentifier qui est journaliste et qui ne l’est pas, côtoie un discours de conciliation et d’adhésion, mettant en avant la force symbolique de cette carte et la forme d’aboutissement identitaire que sa délivrance continue d’incarner. Il est significatif de noter que les instances d’agréation adaptent leurs pratiques, plus que leurs discours, à ces nouvelles situations professionnelles et aux identités qui en découlent : la délivrance de la carte de presse se fait de plus en plus au cas par cas, et avec une certaine

  10. Does community participation set the local press agenda? A view on deliberative and civic practices in the Portuguese press

    OpenAIRE

    Ferreira, Gil Baptista

    2013-01-01

    What are journalists’ perceptions of the citizen’s role in democratic life? What is the role that journalists attribute to the public in the construction of the news agenda? The main goal of this study is to investigate the relationship between the local press, citizens and civic practices. It takes as starting point a dual theoretical approach, the theory of deliberative democracy and the public journalism movement, to assess the scope of the concept of “deliberative journalism.” Under the a...

  11. Ireland’s Press Ombudsman, John Horgan, on accountability, regulation and redress: Where do press councils stand?

    OpenAIRE

    Horgan, John

    2012-01-01

    In recent years, the creation of a number of press councils in Europe and elsewhere, as well as the concurrent appointment of internal ombudsmen or readers’ representatives in many significant newspapers, particularly in the United States, is a clear response to a growing public perception that there is a need for an appropriate level of accountability for the print media. It is fair to assume that this is related, in part, to a public perception that there is a need for remedies for abuses o...

  12. International Commercial Contracts, by Giuditta Cordero Moss. (Cambridge: Cambridge University Press, 2014)

    DEFF Research Database (Denmark)

    Lando, Ole

    2015-01-01

    Review of: Giuditta Cordero Moss, International Commercial Contracts. Cambridge: Cambridge University Press, 2014. XV + 329 pages. ISBN: 9781107684713......Review of: Giuditta Cordero Moss, International Commercial Contracts. Cambridge: Cambridge University Press, 2014. XV + 329 pages. ISBN: 9781107684713...

  13. Reporters on the Battlefield. The Embedded Press System in Historical Context

    National Research Council Canada - National Science Library

    Paul, Christopher; Kim, James J

    2004-01-01

    While the history of relations between the press and the military predates modern journalism, much of what had gone before was neutralized by the horrible press-military breakdown that occurred during U.S...

  14. A Comparison of Coverage of Speech and Press Verdicts of Supreme Court.

    Science.gov (United States)

    Hale, F. Dennis

    1979-01-01

    An analysis of the coverage by ten newspapers of 20 United States Supreme Court decisions concerning freedom of the press and 20 decisions concerning freedom of speech revealed that the newspapers gave significantly greater coverage to the press decisions. (GT)

  15. Properties of nonvolatile and antibacterial bioboard produced from bamboo macromolecules by hot pressing

    Directory of Open Access Journals (Sweden)

    Shengbo Ge

    2018-03-01

    Full Text Available Employing the antibacterial property of industrial bamboo vinegar (IBV and the photocatalytic degradation of TiO2, bamboo macromolecules were pretreated and processed into nonvolatile and antibacterial bio board (NVABB. The NVABB was then analyzed by conducting Fourier-transform infrared spectroscopy, thermogravimetric analysis and differential thermal analysis. Results show that NVABB samples had average density of 0.96 g/cm3, which is appropriate for application. In terms of physical and mechanical properties, the best NVABB sample obtained from IBV, TiO2 and bamboo had an IBV pretreatment time of 10 min, 2% TiO2 and 1% bamboo charcoal. Fourier-transform infrared spectroscopy demonstrated that optimum conditions for hot pressing were a temperature of 170 °C, duration of 15 min and the addition of IBV and TiO2. Thermogravimetric analysis/differential thermal analysis curves suggest that the thermal degradation of NVABB was less than that of bamboo and that hot pressing obviously increased the thermal stability of HDBB samples. Analysis of the antimicrobial effect revealed that IBV pretreatment improves the antibacterial property of NVABB. Keywords: Industrial bamboo vinegar, Nonvolatile and antibacterial bio board, Bamboo macromolecules, Fourier-transform infrared spectroscopy, Thermogravimetric analysis/differential thermal analysis

  16. Pulsed electric field pretreatment of rapeseed green biomass (stems) to enhance pressing and extractives recovery.

    Science.gov (United States)

    Yu, X; Gouyo, T; Grimi, N; Bals, O; Vorobiev, E

    2016-01-01

    The objective of this study was to investigate the effects of pulsed electric field (PEF) pretreatment on the valorization of extractives (proteins and polyphenols) from rapeseed green biomass (stems) by pressing. The effect of pressure, electric field strength and pulse number on the juice expression yield, total polyphenols and total proteins content in the expressed juices were studied. Experiments conducted under optimal conditions (E = 8 kV/cm, tPEF = 2 ms, P = 10 bar) permitted to increase the juice expressed yield from 34% to 81%. Significant increases in total polyphenols content (0.48 vs. 0.10 g GAE/100g DM), in total proteins content (0.14 vs. 0.07 g BSA/100g DM) and in consolidation coefficient (9.0 × 10(-8) vs. 2.2 × 10(-8)m(2)/s) were also observed after PEF pretreatment. The recovered press cake was well dehydrated with an increase of dry matter content from 8.8% to 53.0%. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Attentional Focus and Grip Width Influences on Bench Press Resistance Training.

    Science.gov (United States)

    Calatayud, Joaquin; Vinstrup, Jonas; Jakobsen, Markus D; Sundstrup, Emil; Colado, JuanCarlos; Andersen, Lars L

    2018-04-01

    This study evaluated the influence of different attentional foci for varied grip widths in the bench press. Eighteen resistance-trained men were familiarized with the procedure and performed a one-repetition maximum (1RM) test during Session 1. In Session 2, they used three different standardized grip widths (100%, 150%, and 200% of biacromial width distance) in random order at 50% of 1RM while also engaged in three different attention focus conditions (external focus on the bench press, internal focus on pectoralis major muscles, and internal focus on triceps brachii muscles). Surface electromyography (EMG) signals were recorded from the triceps brachii and pectoralis major, and peak EMG of the filtered signals were normalized to maximum EMG of each muscle. Both grip width and focus influenced the muscle activity level, but there were no significant interactions between these variables. Exploratory analyses suggested that an internal focus may slightly (4%-6%) increase pectoralis major activity at wider grip widths and triceps brachii activity at narrower grip widths, but this should be confirmed or rejected in a study with a larger sample size or through a meta-analysis of research to date.

  18. Synthesis of Cu-CNTs nanocomposites via double pressing double sintering method

    Directory of Open Access Journals (Sweden)

    Marjan Darabi

    2018-01-01

    Full Text Available In this research, copper (Cu-carbon nanotubes (CNTs nanocomposites were synthesized with different weight percentages of CNTs by double pressing double sintering (DPDS method as well as conventional sintering method. A planetary ball mill was used to disperse CNTs in Cu matrix. The milled powders were first cold pressed to 450 MPa in a uniaxial stainless-steel die with cylindrical compacts (diameter: 12 mm and height: 5 mm. The effect of CNTs content and the DPDS method on the properties of the nanocomposites were investigated. The microstructure and phase analysis of Cu-CNTs nanocomposite samples were studied by FESEM and X-Ray Diffraction. The electrical conductivity of nanocomposites was measured and compared to both sintering methods. Mechanical properties of Cu-CNTs nanocomposites were characterized using bending strength and micro-hardness measurements. Enhancements of about 32% in bending strength, 31.6% in hardness and 19.5% in electrical conductivity of Cu-1 wt.% CNTs nanocomposite synthesized by DPDS method were observed as compared to Cu-1 wt.% CNTs nanocomposites fabricated under the similar condition by a conventional sintering process.

  19. Pressing and tubes rolling out of tungsten of gas phase deposition

    International Nuclear Information System (INIS)

    Korolev, Yu.M.; Kosachev, L.S.; Semiletov, S.S.; Solov'ev, V.F.; Sorkin, V.A.

    1987-01-01

    The possibility of increasing ductility of tubes of tungsten fluoride using heat treatment and plastic deformation- pressing and thermal rolling are studied. When designing the processes of treatment it should be necessarily taken into account that structural state of initial blanks as well as the ratio of deformations in radial and tangential directions under pressing with a rigid needle strongly affects technological properties of pressed tubes. The columnar structure of blanks is undesirable for its embrittlement affects the pressed tubes

  20. Solidification of ion-exchange resins by hydrothermal hot-pressing

    International Nuclear Information System (INIS)

    Kaneko, M.

    1993-01-01

    The solidification reaction which easily occurs while continuously keeping the mixture of cation and anion exchange resins compressed under hydrothermal conditions has been demonstrated. Dehydration was considered to occur between sulphonic acid (-SO 3 H) from the cation exchange resin and quaternary ammonium [-CH 2 -N(CH 3 ) 3 OH] from anion-exchange resin-on terminal groups. The cation-and anion-exchange resins were mixed in a 1:1 weight ratio, put in a hot-pressing autoclave and compressed between pistons from the top and bottom at 600 kg cm -2 pressure. The material was continuously compressed during hydrothermal treatment at 200 kg cm -2 by a hydraulic jack and heated to a desired temperature with an induction heater. This system could be used for rapid temperature increasing up to 30 o c min -1 . The pressure and temperature were kept constant for 10 min. The autoclave was cooled to room temperature after the hydrothermal treatment. After the specimen was taken out, the ion-exchange radical reactions were estimated and the product structures were examined. The cation- and anion-exchange resin mixture was solidified. The resultant solidified body at a 300 o C reaction condition for 10 min had a 1.0 g cm -3 density and 700 kg cm -2 compressive strength, and the weight loss did not change in distilled water for 2 weeks. On the other hand, a solidification reaction did not occur at below 250 o C when only the cation or anion was solidified, but they were decomposed. These results suggest that a mixture of cation- and anion-exchange resins causes a solidification reaction under hydrothermal hot-pressing conditions at 300 o C. (author)

  1. Design and testing of a solar photovoltaic operated multi-seeds oil press

    Energy Technology Data Exchange (ETDEWEB)

    Mpagalile, J.J. [Department of Food Science and Technology, Sokoine University of Agriculture, P.O. Box 3006, Morogoro (Tanzania); Hanna, M.A.; Weber, R. [Industrial Agricultural Products Center, University of Nebraska, 209 L.W. Chase Hall, Lincoln, NE 68583-0730 (United States)

    2006-10-15

    Oil expression tests were conducted to evaluate the performance of a novel oil expeller designed and fabricated to operate on a 200W solar photovoltaic (PV) power system as a sole power source. The oil press was designed to press oilseeds meal with intermediate moisture content of 12+/-1% (w.b.) and 0.5-2mm particle sizes. Freshly grated coconuts and ground peanuts were used to determine the oil expression efficiency of the press. The oilseed samples were pressed for 12min with a maximum pressure of 3.0MPa being reached at 6min of pressing for peanuts and 8min of pressing for coconuts. The pressure was then held for the rest of the pressing time. The press attained an average oil expression efficiency of 73% for coconuts and 70% for peanuts. The force-vs.-deformation studies indicated that peanut press meal was compacted at a higher rate as compared to coconuts. The observation on the energy consumption indicated that there was a significant increase (P<0.05) in the specific energy requirement for both coconuts and peanuts after 6min of pressing, which resulted from the solidification of the press cake. An average specific energy of 36.55 and 20.35Wh/kg was recorded for peanuts and coconuts, respectively, after 12min of pressing. (author)

  2. Pronouncements and Denunciations: An Analysis of State Press Association Ethics Codes from the 1920s.

    Science.gov (United States)

    Cronin, Mary M.; McPherson, James B.

    1995-01-01

    Discusses how four situational concerns (the rise of press agents, the fallout from World War I propaganda, sensationalism's resurgence, and editorial independence) contributed to a noticeable decline of the public's trust in the press. Shows how, as a result, 12 state press association ethics codes from the 1920s consistently emphasized the…

  3. Student Press in American Archives, Fall/Winter 1973-74.

    Science.gov (United States)

    National Council of Coll. Publications Advisers.

    This issue of the "Student Press in America Archives List" contains 100 entries on current issues and information, as well as cases involving student press editors, advisers, student media, and the generic subject of the campus press, emphasizing censorship practices and principles. Information concerning how and where to obtain documents of…

  4. A Low-Cost Auto-Stop Hydraulic Press for Making KBr Disc

    Science.gov (United States)

    Hon, Ping-Kay

    1998-05-01

    A hydraulic press fitted with an adjustable torque wrench, together with a stand made of iron bars will form an auto-stop hydraulic press for making KBr disc in IR studies. Total material cost is about $100. All parts are readily available from the local hardware stores. The modified torque wrench is also useful to replace the lever in the standard laboratory press.

  5. A Simplified Model of an Offset Ram Press for Sunflower Oil ...

    African Journals Online (AJOL)

    This paper presents the theoretical analysis of a simplified model of a ram press. The design of the ram press is based on the classical slider-crank mechanism. A force analysis of the press was performed for several successive positions of the driving lever (handle) and for a range of values of certain dimensionless ...

  6. Type synthesis for 4-DOF parallel press mechanism using GF set theory

    Science.gov (United States)

    He, Jun; Gao, Feng; Meng, Xiangdun; Guo, Weizhong

    2015-07-01

    Parallel mechanisms is used in the large capacity servo press to avoid the over-constraint of the traditional redundant actuation. Currently, the researches mainly focus on the performance analysis for some specific parallel press mechanisms. However, the type synthesis and evaluation of parallel press mechanisms is seldom studied, especially for the four degrees of freedom(DOF) press mechanisms. The type synthesis of 4-DOF parallel press mechanisms is carried out based on the generalized function(GF) set theory. Five design criteria of 4-DOF parallel press mechanisms are firstly proposed. The general procedure of type synthesis of parallel press mechanisms is obtained, which includes number synthesis, symmetrical synthesis of constraint GF sets, decomposition of motion GF sets and design of limbs. Nine combinations of constraint GF sets of 4-DOF parallel press mechanisms, ten combinations of GF sets of active limbs, and eleven combinations of GF sets of passive limbs are synthesized. Thirty-eight kinds of press mechanisms are presented and then different structures of kinematic limbs are designed. Finally, the geometrical constraint complexity( GCC), kinematic pair complexity( KPC), and type complexity( TC) are proposed to evaluate the press types and the optimal press type is achieved. The general methodologies of type synthesis and evaluation for parallel press mechanism are suggested.

  7. The news value of Dutch corporate press releases as a predictor of corporate agenda building power

    NARCIS (Netherlands)

    Schafraad, P.; van Zoonen, W.; Verhoeven, P.

    2016-01-01

    This study focuses on explaining agenda building power of corporate press releases. The purpose of the study is to investigate to what extent news factor theory can be applied to predict whether a press release generates media attention or not. A content analysis of 823 press releases from 30 of the

  8. Hot isostatic pressing of glass-zeolite composites

    International Nuclear Information System (INIS)

    Hash, M.C.; Pereira, C.; Lewis, M.A.

    1996-01-01

    Glass-zeolite waste forms are being developed for immobilizing the chloride waste salt generated from the electrometallurgical treatment of spent fuel. Glass-zeolite composites with high densities were made using hot isostatic pressing (HIP) techniques. Processing parameters were investigated to yield desirable structural ceramic properties such as mechanical, chemical, and thermal stability. Limits for these parameters were determined by differential thermal and thermogravimetric analysis. The resulting ceramic properties such as bulk density, open or apparent porosity, and leach resistance were determined. In addition, phase equilibria and particle-size distribution were observed by optical light and electron microscopy. Pre-HIP processing techniques were also studied to ensure intimate mixing of the glass and zeolite powders. Particle size distributions resulting from dry blending procedure are appropriate for needed flow and packing characteristics

  9. Ultrafine grained steels processed by equal channel angular pressing

    International Nuclear Information System (INIS)

    Shin, Dong Hyuk; Park, Kyung-Tae

    2005-01-01

    Recent development of ultrafine grained (UFG) low carbon steels by using equal channel angular pressing (ECAP) and their room temperature tensile properties are reviewed, focusing on the strategies overcoming their inherent mechanical drawbacks. In addition to ferrite grain refinement, when proper post heat treatments are imposed, carbon atom dissolution from pearlitic cementite during ECAP can be utilized for microstructural modification such as uniform distribution of nano-sized cementite particles or microalloying element carbides inside UFG ferrite grains and fabrication of UFG ferrite/martensite dual phase steel. The utilization of nano-sized particles is effective on improving thermal stability of UFG low carbon ferrite/pearlite steel but less effective on improving its tensile properties. By contrast, UFG ferrite/martensite dual phase steel exhibits an excellent combination of ultrahigh strength, large uniform elongation and extensive strain hardenability

  10. THE FRAMING OF RARE DISEASES IN SPANISH PRESS

    Directory of Open Access Journals (Sweden)

    Sebastián Sánchez Castillo

    2014-06-01

    Full Text Available The news frame analysis has become a basic tool to understand the cognitive structures that construct social reality in its many facets. The objective of this research is to reveal the basic frames and generic frames that define the treatment of rare diseases in the Spanish press. The content analysis of 216 news items about rare diseases published in El País, El Mundo and ABC from August 2010 to September 2012 has been determined to a large extent the problem is presented as a complex social reality rather than how a disease more. Human interest based on personalization of information is the most important generic framing. These results may contribute to greater social visibility of the Rare Diseases.

  11. Anglicism in the press of Santiago de Cuba city

    Directory of Open Access Journals (Sweden)

    Yusnel Tabares-Tabares

    2017-06-01

    Full Text Available The preliminary findings from an unfinished investigation having a synchronic approach are presented. The objective of this study is to analyze the English loanwords that appear in the press of Santiago de Cuba city at the beginning of the XX century. This analysis will allow to draw significant conclusions concerning the presence of anglicisms in the Spanish spoken in Cuba. The methodology is based on a random revision of “El Cubano Libre” newspaper, at the time it is counted some aspects, namely: how many anglicisms were found, their typology, grammatical category, their frequency of appearance, and the year they were published in the dictionary of the Spanish Royal Academy.  Among the outstanding results is remarkable that few English loanwords were registered in the dictionary of the Spanish Royal Academy, the topics more profitable to search were those of politics and sport, and the sort of anglicisms more frequent belong to the category of patent loanword.

  12. Press conference bring excitement of geophysical research to the public

    Science.gov (United States)

    Leifert, Harvey

    “A Flare to Remember.” “Starbucks for Starfish.” “Earth's Rotation Slows for El Niño.” What do these catchy headlines have in common? They all resulted from presentations at AGU's Spring Meeting in Boston, Mass. Yes, geophysical science can be big news when presented in a way that is interesting to general audiences.Proof? Well, the “Flare to Remember” headline (in the Dallas Morning News) reported the discovery, via the SOHO spacecraft, that a solar flare had produced, deep inside the Sun, seismic disturbances of a magnitude never experienced on Earth. Researchers Valentina Zharkova of Glasgow University and Alexander Kosovichev of Stanford gave media representatives a preview of their session, supported by visual aids, in the AGU press briefing room.

  13. Cultural Appropriations; Ethnic-Racial Representations; Black Press

    Directory of Open Access Journals (Sweden)

    Maria Angélica Zubaran

    2015-12-01

    Full Text Available This paper investigates the exchange and circulation of ideas in the black diaspora, particularly in the newspaper The Example, mapping and discussing the ethnic-racial and gender representations constructed in the narratives produced by the editors of this newspaper, during the campaign for the construction of a monument to the “Black Mother”. The aim is to analyze how the newspaper’s editors have appropriated texts that circulated in other newspapers about the campaign to the monument of the “Black Mother”, adapted them to their own interests and given them new meanings. From the theoretical approach of Cultural Studies, we understand the black press as a cultural artifact that not only informs but also produces discourses and representations that contribute to the formation of black subjectivities and identities.

  14. Conference/debate on nuclear power. Press file

    International Nuclear Information System (INIS)

    1998-01-01

    This press dossier presents in a digest way the advantages of nuclear power with respect to other energy sources. After a presentation of the worldwide energy resources (electric power demand, fossil-fuel reserves, renewable energies, environmental constraints), the dossier describes the functioning principle of a PWR reactor as a presentation of the French nuclear program (historical aspects, policy, organization of activities, trade, EPR project). In the last part, the sociological aspects of nuclear power are approached: environmental aspects (natural radioactivity, reactors safety, radioactive wastes, environment protection, carbon dioxide and energy production), and public health aspects (principles of radioactivity, dose effects, industrial and scientific applications of radionuclides, nuclear controversy, reactor accidents, legal aspects of radioprotection, safety standards and controls). (J.S.)

  15. Ductility in hot isostatically pressed 250-grade maraging steel

    International Nuclear Information System (INIS)

    German, R.M.; Smugeresky, J.E.

    1978-01-01

    Prealloyed 250-grade maraging steel powder produced by the rotating electrode process was fully consolidated by hot isostatic pressing (HIP) at 1100 and 1200 0 C. The strength following aging (3 h at 480 0 C) equalled that of wrought material; however, ductility was negligible. This lack of ductility in the powder metallurgy product was traced to titanium segregation which occurred at the powder surface during power production. The formation of a titanium intermetallic at the prior particle boundaries during aging caused failure at low plastic strains. Altered aging treatments successfully broke up the embrittling film and resulted in a significant ductility recovery for the HIP material. Analysis of the fracture process indicates that further ductility gains are possible by reducing the titanium content, refining the particle size, and optimizing the thermal cycles

  16. Techniques for hot-press-bonding dissimilar metal combinations

    International Nuclear Information System (INIS)

    Watson, R.D.

    1966-05-01

    High strength diffusionless bonds can be produced in a variety of dissimilar metal combinations by the hot press bonding technique covered by Canadian Patent application 904,548 June 6, 1964. Some of the combinations that can be joined successfully are Zircaloy-2 and 416 stainless steel, 416 stainless steel and mild steel, 1S aluminum and mild steel, Zircaloy-2 and M257 SAP, and Zircaloy-2 and 1S aluminum. Several other combinations were attempted but suitable joints could not be produced. The methods of producing the joints, the joint strength that can be developed and a discussion of some of the problems associated with making the joints are included in the report. (author)

  17. Press briefing on results from the solar spacecraft SOHO

    Science.gov (United States)

    1998-04-01

    After its launch on 2 December 1995, SOHO travelled to take up a special orbit 1.5 million kilometres away on the sunward side of the Earth, where the Sun never sets. The full scientific programme began in April 1996. The occasion for the briefing is the celebration of that second anniversary and of the mission's extension to 2003. Organized by the European Space Agency, the briefing will be hosted by the Rutherford Appleton Laboratory, which is near Oxford. Leading scientists associated with SOHO will announce to the press some remarkable new discoveries about the Sun's interior, atmosphere and solar wind. They will also briefly review the main achievements of the past two years. The role of SOHO as the chief watchdog for storms on the Sun that may affect the Earth will be demonstrated. Europe's creation of the finest spacecraft ever built to observe the Sun will be recalled by a top engineer from ESA. A speaker from NASA will explain transatlantic contributions to SOHO, which is a project of international cooperation between ESA and NASA. ESA's director of science will also be present, to relate SOHO to ESA's general science programme. A lunch-time talk by the BNSC's director of science completes the line-up of speakers. This is also an exceptional opportunity for the press to meet and interview scientists from all over Europe and the USA, who are attending a meeting at the Rutherford Appleton Laboratory of SOHO's Science Working Team (SWT). Journalists are usually excluded from such meetings. The Rutherford Appleton Laboratory plays a prominent part in SOHO, particularly through its provision of the CDS ultraviolet spectrometer. A visit to the CDS group will provide a chance to see what space research is really like. Please indicate your intention to attend, on the accreditation form that follows the schedule. Guidance on how to get to the Rutherford Appleton Laboratory is appended. PROGRAMME Rutherford Appleton Laboratory (RAL), 28 April 1998 10:30 Assembly of

  18. Reading and Not-Printing: Obstruction at the Crater Press

    Directory of Open Access Journals (Sweden)

    Richard Parker

    2014-11-01

    Full Text Available I will begin this paper with a brief and partial history of American printing, detecting a shared predilection for a noticeably maverick relation to the printed page in the works (printed and otherwise of Samuel Keimer and Benjamin Franklin during the colonial period, and the works of Walt Whitman, Emily Dickinson and Mark Twain in the nineteenth-century. I term the interrupted, dialectical printing that connects all of these writer/printers ‘not-printing’, and offer some explanation of his term and a description of some of its manifestations. I will then move on to consider how the idea of ‘not-printing’ might be helpful for the consideration of some contemporary British and American poets and printers before concluding with a description of some of the ways that the productive constraints of such a practice have influenced my own work as editor and printer at the Crater Press.

  19. Texture in equal-channel angular pressed aluminum and nickel

    Energy Technology Data Exchange (ETDEWEB)

    Vogel, S.C.; Beyerlein, I.J.; Bourke, M.A.M.; Tome, C.N.; Rangaswamy, P. [Los Alamos National Lab., Los Alamos, NM (United States); Xu, C.; Langdon, T.G. [Univ. of Southern California, Los Angeles, CA (United States)

    2002-07-01

    Nano-structured metals with advantageous mechanical properties can be produced using severe plastic deformation techniques such as equal channel angular pressing (ECAP). Metals and alloys processed by ECAP have much higher yield strengths than the equivalent unprocessed material while retaining high ductilities, an extremely attractive combination of properties. Implicit in the process are the introduction of repetitive shear strains of 100% which introduce texture, the modeling of which is challenging. In this work, we present results from a neutron diffraction study on aluminum and nickel samples processed by ECAP. The results are compared to predictions from a visco-plastic self-consistent (VPSC) model. By taking into account grain-grain interactions in the model the agreement between the predicted and measured orientation distributions is improved. The results show also that the initial texture affects the texture evolution, at least up to strains of the order of {proportional_to}1, i.e. one ECAP pass. (orig.)

  20. Hot isostatic pressing of nanosized WC-Co hardmetals

    International Nuclear Information System (INIS)

    Azcona, I.; Ordonez, A.; Sanchez, J.M.; Castro, F.; Dominguez, L.

    2001-01-01

    A new technique based on hot isostatic pressing (HIP) has been developed to produce dense nanosized WC-Co hardmetals without the addition of grain growth inhibitors. The glass encapsulation process is the key for the effective application of isostatic pressure at temperatures well below those usually required for reaching the closed porosity state in the WC-Co system. Fully dense WC-Co samples with cobalt contents ranging from 10 to 12 wt. % have been obtained by this technique at temperatures between 1000 o C and 1200 o C with 150 MPa of applied isostatic pressure for 30 minutes. The role of isostatic pressure on the activation of densification mechanisms is discussed. (author)

  1. Cold-pressed and hot-pressed rapeseed oil: The effects of roasting and seed moisture on the antioxi- dant activity, canolol, and tocopherol level.

    Science.gov (United States)

    Siger, Aleksander; Józefiak, Marta; Górnaś, Paweł

    2017-01-01

    The paper looks at the levels of canolol, tocopherols and antioxidant activity in cold-pressed and hot-pressed rapeseed oils produced from seeds of various moisture levels (5%, 7.5%, and 10%). The paper also considers the effects of seed roasting on the levels of these compounds. The material used for the tests was rapeseed cv. Adrianna. The quality of the oils obtained is determined using peroxide and acid values. The levels of canolol and tocopherols are analyzed using HPLC. The DPPH radical-scavenging activity method for oil samples and phenolic extract from oils was used. It has been demonstrated that the oils produced from rapeseeds with a 5% moisture content, and   in particular from cold-pressed oils, were characterized by the lowest peroxide values. Cold-pressed oils produced from rapeseeds with a 5% moisture content were characterized by higher levels of tocopherols and plastochromanol-8. In the case of hot-pressed oils, the highest levels of tocopherols were found in oils pro- duced from seeds with a 7.5% moisture content, and the greatest amount of PC-8 (more than 4 mg/100 g) was found in oils produced from seeds with a 10% moisture content. Hot-pressed oils have been shown to have higher levels of these compounds than cold-pressed oils. Both roasting and hot pressing led to an increase in the amount of canolol in the oils investigated. When analysing the antioxidant activity of the oils and phenolic extracts it was shown that phenolic compounds are responsible for approx. 10% of total antioxidant activity. Various levels of biologically active compounds were shown to be present in the rapeseed oil obtained from raw materials of a varying moisture content. The type of pressing process (cold-pressing or hot-pressing) and whether the seeds have undergone roasting has also been shown to affect the resulting oil and the level of native antioxidants it contains.

  2. Fatigue effects on bar kinematics during the bench press.

    Science.gov (United States)

    Duffey, Michael J; Challis, John H

    2007-05-01

    The bench press is one of the most popular weight training exercises. Although most training regimens incorporate multiple repetition sets, there are few data describing how the kinematics of a lift change during a set to failure. To examine these changes, recreational lifters (10 men and 8 women) were recruited. The maximum weight each subject could bench press (1RM) was determined. Subjects then performed as many repetitions as possible at 75% of the 1RM load. Three-dimensional kinematic data were recorded and analyzed for all lifts. Statistical analysis revealed that differences between maximal and submaximal lifts and the kinematics of a submaximal lift change as a subject approaches failure in a set. The time to lift the bar more than doubled from the first to the last repetition, causing a decrease in both mean and peak upward velocity. Furthermore, the peak upward velocity occurred much earlier in the lift phase in these later repetitions. The path the bar followed also changed, with subjects keeping the bar more directly over the shoulder during the lift. In general, most of the kinematic variables analyzed became more similar to those of the maximal lift as the subjects progressed through the set, but there was considerable variation between subjects as to which repetition was most like the maximal lift. This study shows that there are definite changes in the lifting kinematics in recreational lifters during a set to failure and suggests it may be particularly important for coaches and less-skilled lifters to focus on developing the proper bar path, rather than reaching momentary muscular failure, in the early part of a training program.

  3. Ductile Fracture Behaviour of Hot Isostatically Pressed Inconel 690 Superalloy

    Science.gov (United States)

    Cooper, A. J.; Brayshaw, W. J.; Sherry, A. H.

    2018-04-01

    Herein we assess the differences in Charpy impact behavior between Hot Isostatically Pressed and forged Inconel 690 alloy over the temperature range of 300 °C to - 196 °C. The impact toughness of forged 690 exhibited a relatively small temperature dependence, with a maximum difference of ca. 40 J measured between 300 °C and - 196 °C, whereas the HIP'd alloy exhibited a difference of approximately double that of the forged alloy over the same temperature range. We have conducted Charpy impact testing, tensile testing, and metallographic analyses on the as-received materials as well as fractography of the failed Charpy specimens in order to understand the mechanisms that cause the observed differences in material fracture properties. The work supports a recent series of studies which assess differences in fundamental fracture behavior between Hot Isostatically Pressed and forged austenitic stainless steel materials of equivalent grades, and the results obtained in this study are compared to those of the previous stainless steel investigations to paint a more general picture of the comparisons between HIP vs forged material fracture behavior. Inconel 690 was selected in this study since previous studies were unable to completely omit the effects of strain-induced martensitic transformation at the tip of the Chary V-notch from the fracture mechanism; Inconel 690 is unable to undergo strain-induced martensitic transformation due to the alloy's high nickel content, thereby providing a sister study with the omission of any martensitic transformation effects on ductile fracture behavior.

  4. Presence of Spotters Improves Bench Press Performance: A Deception Study.

    Science.gov (United States)

    Sheridan, Andrew; Marchant, David C; Williams, Emily L; Jones, Hollie S; Hewitt, Phil A; Sparks, S Andy

    2017-10-24

    Sheridan, A, Marchant, DC, Williams, EL, Jones, HS, Hewitt, PA, and Sparks, SA. Presence of spotters improves bench press performance: a deception study. J Strength Cond Res XX(X): 000-000, 2017-Resistance exercise is a widely used method of physical training in both recreational exercise and athletic populations. The use of training partners and spotters during resistance exercise is widespread, but little is known about the effect of the presence of these individuals on exercise performance. The purpose of the current study was to investigate the effect of spotter presence on bench press performance. Twelve recreationally trained participants (age, 21.3 ± 0.8 years, height, 1.82 ± 0.1 m, and weight, 84.8 ± 11.1 kg) performed 2 trials of 3 sets to failure at 60% of 1 repetition maximum on separate occasions. The 2 trials consisted of spotters being explicitly present or hidden from view (deception). During the trials, total repetitions (reps), total weight lifted, ratings of perceived exertion (RPE), and self-efficacy were measured. Total reps and weight lifted were significantly greater with spotters (difference = 4.5 reps, t = 5.68, p < 0.001 and difference = 209.6 kg, t = 5.65, p < 0.001, respectively). Although RPE and local RPE were significantly elevated in the deception trials (difference = 0.78, f = 6.16, p = 0.030 and difference = 0.81, f = 5.89, p = 0.034, respectively), self-efficacy was significantly reduced (difference = 1.58, f = 26.90, p < 0.001). This study demonstrates that resistance exercise is improved by the presence of spotters, which is facilitated by reduced RPE and increased self-efficacy. This has important implications for athletes and clients, who should perform resistance exercise in the proximity of others, to maximize total work performed.

  5. Influence of different attentional focus on EMG amplitude and contraction duration during the bench press at different speeds.

    Science.gov (United States)

    Calatayud, Joaquin; Vinstrup, Jonas; Jakobsen, Markus D; Sundstrup, Emil; Colado, Juan Carlos; Andersen, Lars L

    2018-05-01

    The purpose of this study was to investigate whether using different focus affects electromyographic (EMG) amplitude and contraction duration during bench press performed at explosive and controlled speeds. Eighteen young male individuals were familiarized with the procedure and performed the one-maximum repetition (1RM) test in the first session. In the second session, participants performed the bench press exercise at 50% of the 1RM with 3 different attentional focuses (regular focus on moving the load vs contracting the pectoralis vs contracting the triceps) at 2 speed conditions (controlled vs maximal speed). During the controlled speed condition, focusing on using either the pectoralis or the triceps muscles increased pectoralis normalized EMG (nEMG) by 6% (95% CI 3-8%; p = 0.0001) and 4% nEMG (95% CI 1-7%; p = 0.0096), respectively, compared with the regular focus condition. Triceps activity was increased by 4% nEMG (95% CI 0-7%; p = 0.0308) at the controlled speed condition during the triceps focus. During the explosive speed condition, the use of different focuses had no effect. The different attentional focus resulted in comparable contraction duration for the measured muscles when the exercise was performed explosively. Using internal focus to increase EMG amplitude seems to function only during conditions of controlled speed.

  6. Flux pinning in hot isostatically pressed Bi2Sr2CaCu2Ox

    International Nuclear Information System (INIS)

    Miller, D.J.; Sengupta, S.; Hettinger, J.D.; Shi, D.; Gray, K.E.; Nash, A.S.; Goretta, K.C.

    1992-01-01

    Magnetic hysteresis data were taken from 4.2 to 35 K on Bi 2 Sr 2 CaCu 2 O x samples that were hot isostatically pressed at 105 MPa in an inert atmosphere at 825 degree C. One set of samples was pressed for only 15 min while the other was pressed for 120 min. The samples pressed for 15 min contained a high density of dislocations and planar faults, while the samples pressed for 120 min contained fewer dislocations and faults, with most dislocations present within subgrain boundaries. The samples with the complex dislocation/planar fault structures exhibited substantially larger hysteresis loops, suggesting enhanced flux pinning

  7. Temperature and press load stimulation on thermal transport in fibrous and porous composite insulators

    International Nuclear Information System (INIS)

    Rehman, M.A.; Maqsood, A.

    2006-01-01

    Thermal transport properties of synthetic pliable insulators are measured as a function of applied pressure at constant temperatures. Advantageous Transient Plane Source (ATPS) method is used for the simultaneous measurement of thermal conductivity and thermal diffusivity of these materials and heat capacity per unit volume is then calculated. Three samples namely foam, closed cell foam and fiber glass are subjected to press load, taking into account the flexibility and sustainability of the samples and the requirements of the technique used. The thermal data of the samples were determined within the temperature range (300-414K) and pressure range (Normal -15kPa). These materials are used for thermal insulation and temperature control of air-conditioned space, acoustic and sound insulation, agriculture and fishery, sports and leisure goods, building and civil engineering, industrial packaging cold storage ware house, boiler work and other electric appliances, so they are helpful in reducing energy losses. (author)

  8. Performance of wind energy in 2015 and future perspectives - Press file

    International Nuclear Information System (INIS)

    Allenet, Tiffany; Resse, Bastien; Kari, Cynthia

    2016-01-01

    This document first proposes a press release which outlines the steady growth of the wind energy installed power in France, the conditions to be met for a continuous progression of wind energy, the necessary development of offshore wind energy production, and the necessity of an agreement with military authorities who still limit wind farm projects because of constraints related to air force training and to military radars. Data are then presented regarding the installed and connected power (manufacturer shares), technical characteristics of the main installed models, installed capacity per region. Brief articles comment the implications of the COP21 for the wind energy sector and French territories, the project of multi-annual planning of energy for 2016-2023, the military constraints and propositions to reduce them, and the rather high growth of employment in the sector

  9. Too Human versus the enthusiast press: Video game journalists as mediators of commodity value

    Directory of Open Access Journals (Sweden)

    Rebecca Carlson

    2009-03-01

    Full Text Available This article examines the role of mediators in the production of commodity value, arguing that there is a rise in a kind of immaterial labor, shaped by contemporary conditions of late capitalism, that functions explicitly as a mediating force. In this example, video game journalists are understood as actively engaged in producing and negotiating the value and meaning of video games for both producers and consumers. By specifically examining a moment of value contestation, a podcast debate between a journalist and a game developer, this article traces the mediating practices of the enthusiast gaming press and examines the way their history with and relationship to the video game industry continue to structure their ability to filter knowledge and shape desires.

  10. Kinetics and mechanisms of creep in hot isostatically pressed niobium carbide

    International Nuclear Information System (INIS)

    Nixon, R.D.; Davis, R.F.; Bentley, J.

    1986-01-01

    Constant compressive stress creep experiments in the temperature and stress ranges of 1730K - 2100K and 16 MN/m 2 - 70 MM/m 2 on HIPed NbC 0.74 have revealed stress exponents of 2.0 under stress levels of 16-54 MN/m 2 at all temperatures investigated and 3.2 under stress levels of 54-70 MN/m 2 at 1830K. The activation energy of steady state creep is approximately 230 kJ/mol in the temperature range of 1730K - 1930K under 48-54 MN/m 2 and 470 kJ/mol in the temperature range of 1900K - 2100K under 64 MN/m 2 . TEM of the annealed but uncrept material reveals grown-in dislocation subboundaries. At 1730K and under 34-54 MN/m 2 , these subboundaries become single dislocations and dipoles. At 1830K and under 54-70 MN/m 2 the subboundaries evolve into simple tilt boundaries which are occasionally knitted, indicating more glide activity at higher stresses. At 1930K and under 34-54 MN/m 2 , hexagonal subboundaries form, but are not as well defined as in the annealed material. At 2100K and under 16-30 MN/m 2 , the subboundaries are well-defined hexagonal networks which become polygonized under higher stresses on 64 MN/m 2 . The experimental and TEM results indicate that at low temperatures (below 0.5 T m = 2073K) and at all stresses, creep occurs by dislocation glide which is accompanied by subgrain and high angle boundary interaction. At high temperature (above 0.5 T m ), strain occurs by glide and subboundary movement; recovery occurs by climb in the subboundary

  11. Shoulder Muscle Activation of Novice and Resistance Trained Women during Variations of Dumbbell Press Exercises

    Science.gov (United States)

    Luczak, Joshua; Bosak, Andy; Riemann, Bryan L.

    2013-01-01

    Previous research has compared the effects of trunk inclination angle on muscle activation using barbells and Smith machines in men. Whether similar effects occur with the use of dumbbells or in women remains unknown. The purpose was to compare upper extremity surface electromyographical (EMG) activity between dumbbell bench, incline, and shoulder presses. Dominate arm EMG data were recorded for collegiate-aged female resistance trained individuals (n = 12) and novice female resistance trained exercisers (n = 12) from which average EMG amplitude for each repetition phase (concentric, eccentric) was computed. No significant differences were found between experienced and novice resistance trained individuals. For the upper trapezius and anterior deltoid muscles, shoulder press activation was significantly greater than incline press which in turn was significantly greater than bench press across both phases. The bench and incline presses promoted significantly greater pectoralis major sternal activation compared to the shoulder press (both phases). While pectoralis major clavicular activation during the incline press eccentric phase was significantly greater than both the bench and shoulder presses, activation during the bench press concentric phase promoted significantly greater activation than the incline press which in turn was significantly greater than the shoulder press. These results provide evidence for selecting exercises in resistance and rehabilitation programs. PMID:26464884

  12. Shoulder Muscle Activation of Novice and Resistance Trained Women during Variations of Dumbbell Press Exercises

    Directory of Open Access Journals (Sweden)

    Joshua Luczak

    2013-01-01

    Full Text Available Previous research has compared the effects of trunk inclination angle on muscle activation using barbells and Smith machines in men. Whether similar effects occur with the use of dumbbells or in women remains unknown. The purpose was to compare upper extremity surface electromyographical (EMG activity between dumbbell bench, incline, and shoulder presses. Dominate arm EMG data were recorded for collegiate-aged female resistance trained individuals ( and novice female resistance trained exercisers ( from which average EMG amplitude for each repetition phase (concentric, eccentric was computed. No significant differences were found between experienced and novice resistance trained individuals. For the upper trapezius and anterior deltoid muscles, shoulder press activation was significantly greater than incline press which in turn was significantly greater than bench press across both phases. The bench and incline presses promoted significantly greater pectoralis major sternal activation compared to the shoulder press (both phases. While pectoralis major clavicular activation during the incline press eccentric phase was significantly greater than both the bench and shoulder presses, activation during the bench press concentric phase promoted significantly greater activation than the incline press which in turn was significantly greater than the shoulder press. These results provide evidence for selecting exercises in resistance and rehabilitation programs.

  13. Effect of Bench Press Load Knowledge on Repetitions, Rating of Perceived Exertion, and Attentional Focus.

    Science.gov (United States)

    Beaudoin, Christina M; Cox, Zachary; Dundore, Tyler; Thomas, Tayler; Kim, Johnathon; Pillivant, Daniel

    2018-02-01

    Beaudoin, CM, Cox, Z, Dundore, T, Thomas, T, Kim, J, and Pillivant, D. Effect of bench press load knowledge on repetitions, rating of perceived exertion, and attentional focus. J Strength Cond Res 32(2): 514-519, 2018-Few studies have examined the role of the teleoanticipation during resistance training. The purpose of this study was to examine the effect of bench press (BP) load knowledge on repetitions completed, ratings of perceived exertion (RPEs), and attentional focus (% associative). Thirty-six recreationally active resistance-trained men (n = 25) and women (n = 11) participated in this study (age = 20.97 ± 1.87 years; ht = 174.12 ± 9.41 cm; and mass = 80.14 ± 14.03 kg). All subjects completed 3 testing sessions: (a) 1 repetition maximum (1RM) BP determination; (b) submaximal BP repetitions to fatigue known load (KL); and (c) submaximal BP repetitions to fatigue unknown load (UL). Known load and UL sessions were randomized and counterbalanced and both completed at 70% 1RM. An estimated weight ratio was computed using the subject's estimate of the UL weight relative to the KL weight. An independent samples t-test revealed no significant testing order difference for the estimated weight ratio. Two-way repeated-measures analysis of variances revealed no significant differences in the number of repetitions (p = 0.63), RPE (p = 0.18), or attentional focus (% associative) (p = 0.93) between the KL and UL conditions. Pearson correlations found a moderate positive association between KL repetitions completed and % associative focus when the UL was completed before the KL. Load knowledge did not influence the number of repetitions, RPE, or attentional focus while completing the BP. Further research examining the use of pacing strategies, RPE, and attentional focus during KL and UL conditions are warranted.

  14. Influence of ballistic bench press on upper body power output in professional rugby players.

    Science.gov (United States)

    West, Daniel J; Cunningham, Daniel J; Crewther, Blair T; Cook, Christian J; Kilduff, Liam P

    2013-08-01

    The use of heavy resistance exercise provides an effective preload stimulus for inducing postactivation potentiation (PAP) and increasing peak power output (PPO). However, this approach has limited application in many sporting situations (e.g., incorporation in a precompetition warm-up); and therefore, more practical strategies for inducing PAP need to be investigated. The aim of the present study was to compare the PPO changes after performing a preload stimulus of either a ballistic exercise or a traditional heavy resistance exercise. Twenty professional rugby union players completed 3 testing sessions, each separated by 48 hours. On the first occasion, subjects underwent a 3 repetition maximum (3RM)-bench press testing session. On the next 2 occasions, subjects performed a ballistic bench throw at baseline (30% of 1RM), followed by a preload stimulus of either heavy resistance training (HRT) (heavy bench press: 3 sets of 3 repetitions at 87% 1RM) or BBP (3 sets of 3 repetitions at 30% on 1RM) followed by ballistic bench throw after 8 minutes recovery. The trials were randomized and counterbalanced. Both preload stimuli protocols increased PPO compared with baseline (BBP baseline 892 ± 108 vs. 8 minutes 924 ± 119 W, p < 0.001; HRT baseline 893 ± 104 vs. 8 minutes 931 ± 116 W; p < 0.001). There were no conditional differences between PPO at 8 minutes (p = 0.141); moreover, the change in PPO from baseline was also similar between conditions (BBP Δ + 33 ± 18; HRT Δ + 38 ± 21 W; p = 0.112). In conclusion, a ballistic exercise provided an effective method of inducing PAP and increasing upper-body PPO; moreover, this elicited similar increases in PPO as a traditional heavy resistance exercise preloading stimulus.

  15. The Mediated Amplification of a Crisis: Communicating the A/H1N1 Pandemic in Press Releases and Press Coverage in Europe.

    Science.gov (United States)

    Rossmann, Constanze; Meyer, Lisa; Schulz, Peter J

    2018-02-01

    In the aftermath of the A/H1N1 pandemic, health authorities were criticized for failures in crisis communication efforts, and the media were accused of amplifying the pandemic. Considering these criticisms, A/H1N1 provides a suitable case for examining risk amplification processes that may occur in the transfer of information from press releases to print news media during a health crisis. We integrated the social amplification of risk framework with theories of news decisions (news values, framing) in an attempt to contribute to existing research both theoretically and empirically. We conducted a quantitative content analysis of press releases disseminated by health and governmental authorities, as well as the quality and tabloid press in 10 European countries between March 2009 and March 2011. Altogether 243 press releases, 1,243 quality press articles, and 834 tabloid press articles were coded. Consistent with research on news values and framing the results suggest that quality and tabloid papers alike amplified A/H1N1 risks by emphasizing conflict and damage, presenting information in a more dramatized way, and using risk-amplifying frames to a greater extent and risk-attenuating frames to a lesser extent than press releases. To some extent, the quality and tabloid press differed in how risk information was presented. While tabloid press articles seemed to follow the leading quality press with regards to content and framing of health crisis coverage, they exhibited a stronger emphasis on drama and emotion in the way they presented information. © 2017 Society for Risk Analysis.

  16. Characterization of creep properties and creep textures in pure aluminum processed by equal-channel angular pressing

    International Nuclear Information System (INIS)

    Kawasaki, Megumi; Beyerlein, Irene J.; Vogel, Sven C.; Langdon, Terence G.

    2008-01-01

    High-purity aluminum was processed by equal-channel angular pressing (ECAP) and then tested under creep conditions at 473 K. The results show conventional power-law creep with a stress exponent of n = 5 which is consistent with an intragranular dislocation process involving the glide and climb of dislocations. It is demonstrated that diffusion creep is not important in these tests because the ultrafine grains produced by ECAP are not stable at this temperature. Texture measurements were undertaken using the high-pressure preferred orientation neutron time-of-flight diffractometer and they reveal significant differences in the evolution of texture during creep in pressed and unpressed specimens. These experimental measurements of texture are in excellent agreement with theoretical textures predicted using a visco-plastic self-consistent model that limits deformation to plastic slip. The calculations provide additional confirmation that creep occurs through an intragranular dislocation process

  17. The effects of combined elastic- and free-weight tension vs. free-weight tension on one-repetition maximum strength in the bench press.

    Science.gov (United States)

    Bellar, David M; Muller, Matthew D; Barkley, Jacob E; Kim, Chul-Ho; Ida, Keisuke; Ryan, Edward J; Bliss, Mathew V; Glickman, Ellen L

    2011-02-01

    The present study investigated the effects of training combining elastic tension, free weights, and the bench press. Eleven college-aged men (untrained) in the bench press participated in the 13-week study. The participants were first given instructions and then practiced the bench press, followed by a one-repetition maximum (1RM) test of baseline strength. Subjects were then trained in the bench press for 3 weeks to allow for the beginning of neural adaptation. After another 1RM test, participants were assigned to 1 of 2 conditions for the next 3 weeks of training: 85% Free-Weight Tension, 15% Elastic Tension (BAND), or 100% Free-Weight Tension (STAND). After 3 weeks of training and a third 1RM max test, participants switched treatments, under which they completed the final 3 weeks of training and the fourth 1RM test. Analysis via analysis of covariance revealed a significant (p ≤ 0.05) main effect for time and interaction effect for Treatment (BAND vs. STAND). Subsequent analysis via paired-samples t-test revealed the BAND condition was significantly better (p = 0.05) at producing raw gains in 1RM strength. (BAND 9.95 ± 3.7 kg vs. STAND 7.56 ± 2.8 kg). These results suggest that the addition of elastic tension to the bench press may be an effective method of increasing strength.

  18. Effective media communication of disasters: Pressing problems and recommendations

    Directory of Open Access Journals (Sweden)

    Ginter Peter M

    2007-06-01

    Full Text Available Abstract Background Public health officials and journalists play a crucial role in disseminating information regarding natural disasters, terrorism and other human-initiated disasters. However, research suggests that journalists are unprepared to cover terrorism and many types of natural disasters, in part because of lack sufficient expertise in science and medicine and training. The objective of this research was to identify solutions to problems facing journalists and public health public information officer (PIOs of communicating with the public during natural and human-initiated disasters. Methods To assist in identifying the most pressing problems regarding media response to health-related risks such as terrorism and large-scale natural disasters, 26 expert advisors were convened, including leaders representing journalists and public information officers, state health officials, experts in terrorism and emergency preparedness, and experts in health, risk, and science communication. The advisory group participated in pre-arranged interviews and were asked to identify and review bioterrorism educational resources provided to journalist. All advisory group members were then invited to attend a day long meeting January 29, 2004 to review the findings and reach consensus. Results The most pressing problems were found to be a lack of coordination between PIO's and journalists, lack of resources for appropriately evaluating information and disseminating it efficiently, and a difference in perception of PIO's and journalist towards each others role during emergency situations. The advisory board developed a list of 15 recommendations that may enhance communication plans betweens PIO's, journalist and the public. The solutions were meant to be feasible in terms of costs and practical in terms of the professional and organizational realities in which journalists and PIO's work. Conclusion It is clear that PIO's and journalists play crucial roles in

  19. Preparation and Mechanical Properties of Pressed Straw Concrete Brick

    Science.gov (United States)

    Sumarni, S.; Wijanarko, W.

    2018-03-01

    Rice straws have been widely used as wall filler material in China, Australia, and United States, by spinning them into hays with an approximate dimension of 40 cm of height, 40cm of thickness and 60 cm of width, using a machine. Then, the hays are placed into a wall frame until they fill it completely. After that, the wall frame is covered with wire mesh and plastered. In this research, rice straws are to be used as concrete brick fillers, by pressing the straws into hays and then putting them into the concrete brick mold along with mortar. The objective of this research is to investigate the mechanical properties of concrete brick, namely: compressive strength, specific gravity, and water absorption power. This research used experimental research method. It was conducted by using concrete bricks which had 400 cm of width, 200 cm of height, and 100 cm of thickness, made from rice straws, cement, sand, and water as the test sample. The straws were each made different by their volume. The mortars used in this research were made from cement, sand, and water, with the ratio of 1:7:0.5. The concrete bricks were made by pressing straws mixed with glue into hays, and then cut by determined variations of volume. The variations of hays volume were 0 m3, 0.000625 m3, 0.00075 m3, 0.000875 m3, 0.00125 m3, 0.0015 m3, 0.00175 m3, 0.001875 m3, 0.00225 m3, and 0.002625 m3. There were 3 samples for each volumes of hays. The result shows that the straw concrete bricks reached the maximum compressive strength of 1.92 MPa, specific gravity of 1,702 kg/m3, and water absorption level of 3.9 %. Based on the provided measurements of products in the Standar Nasional Indonesia (Indonesian product standardization), the concrete bricks produced attained the prescribed standard quality.

  20. Press forging and optical properties of lithium fluoride

    Science.gov (United States)

    Ready, J. F.; Vora, H.

    1980-07-01

    Lithium fluoride is an important candidate material for windows on high power, short-pulse ultraviolet and visible lasers. Lithium fluoride crystals were press forged in one step over the temperature range 300 to 600 C to obtain fine grained polycrystalline material with improved mechanical properties. The deformation that can be given to a lithium fluoride crystal during forging is limited by the formation of internal cloudiness (veiling) with the deformation limit increasing with increasing forging temperature from about 40 percent at 400 C to 65 percent at 600 C. To suppress veiling, lithium fluoride crystals were forged in two steps over the temperature range 300 to 600 C, to total deformations of 69 to 76 percent, with intermediate annealing at 700 C. This technique yields a material which has lower scattering with more homogeneous microstructure than that obtained in one step forging. The results of characterization of various optical and mechanical properties of single crystal and forged lithium fluoride, including scattering, optical homogeneity, residual absorption, damage thresholds, environmental stability, and thresholds for microyield are described.

  1. Press forging and optical properties of lithium fluoride

    International Nuclear Information System (INIS)

    Ready, J.F.; Vora, H.

    1979-01-01

    Lithium fluoride is an important candidate material for windows on high-power, short-pulse ultraviolet and visible lasers. Lithium fluoride crystals have been press forged in one step over the temperature range 300 to 600 0 c to obtain fine-grained polycrystalline material with improved mechanical properties. The deformation that can be given to a lithium fluoride crystal during forging is limited by the formation of internal cloudiness (veiling) with the deformation limit increasing with increasing forging temperature from about 40% at 400 0 C to 65% at 600 0 C. To suppress veiling, lithium fluoride crystals were forged in two steps over the temperature range 300 to 600 0 C, to total deformations of 69-76%, with intermediate annealing at 700 0 C. This technique yields a material which has lower scattering with more homogeneous microstructure than that obtained in one-step forging. The results of characterization of various optical and mechanical properties of single-crystal and forged lithium fluoride, including scattering, optical homogeneity, residual absorption, damage thresholds, environmental stability, and thresholds for microyield are described

  2. Biogas production from Jatropha curcas press-cake.

    Science.gov (United States)

    Staubmann, R; Foidl, G; Foidl, N; Gübitz, G M; Lafferty, R M; Arbizu, V M; Steiner, W

    1997-01-01

    Seeds of the tropical plant Jatropha curcas (purge nut, physic nut) are used for the production of oil. Several methods for oil extraction have been developed. In all processes, about 50% of the weight of the seeds remain as a press cake containing mainly protein and carbohydrates. Investigations have shown that this residue contains toxic compounds and cannot be used as animal feed without further processing. Preliminary experiments have shown that the residue is a good substrate for biogas production. Biogas formation was studied using a semicontinous upflow anaerobic sludge blanket (UASB) reactor; a contact-process and an anaerobic filter each reactor having a total volume of 110 L. A maximum production rate of 3.5 m3 m"3 d"1 was obtained in the anaerobic filter with a loading rate of 13 kg COD m~3 d"1. However, the UASB reactor and the contact-process were not suitable for using this substrate. When using an anaerobic filter with Jatropha curcas seed cake as a substrate, 76% of the COD was degraded and 1 kg degraded COD yielded 355 L of biogas containing 70% methane.

  3. Biogas production from Jatropha curcas press-cake

    Energy Technology Data Exchange (ETDEWEB)

    Staubmann, R.; Guebitz, G.M.; Lafferty, R.M. [Graz Technical Univ. (Austria)] [and others

    1997-12-31

    Seeds of the tropical plant Jatropha curcas (purge nut, physic nut) are used for the production of oil. Several methods for oil extraction have been developed. In all processes, about 50% of the weight of the seeds remain as a press cake containing mainly protein and carbohydrates. Investigations have shown that this residue contains toxic compounds and cannot be used as animal feed without further processing. Preliminary experiments have shown that the residue is a good substrate for biogas production. Biogas formation was studied using a semicontinous upflow anaerobic sludge blanket (UASB) reactor; a contact-process and an anaerobic filter each reactor having a total volume of 110 L. A maximum production rate of 3.5 m{sup 3} m{sup -3} d{sup -1} was obtained in the anaerobic filter with a loading rate of 13 kg COD m{sup -3} d{sup -1}. However, the UAS reactor and the contact-process were not suitable for using this substrate. When using an anaerobic filter with Jatropha curcas seed cake as a substrate, 76% of the COD was degraded and 1 kg degraded COD yielded 355 L of biogas containing 70% methane. 28 refs., 3 figs., 4 tabs.

  4. The approach of nuclear related issues by the press

    International Nuclear Information System (INIS)

    Manetti, Cristiane Teixeira; Tanimoto, Katia Suemi; Hiromoto, Goro

    2009-01-01

    Nuclear energy has always been a polemic issue, and it is usually more intensely associated, by the general public, to the risks than to the benefits from its use; in this sense, the mass media have clearly had its share of responsibility for public opinion formation. This paper presents a report on the coverage of the nuclear issue in the press, identifying the amount of negative and positive views on the subject, as well as the people involved in the process. The analysis comprises the period from February 2007 to February 2008, right after the edition of the 4th IPCC Report. From that sample, 172 texts published in widely known newspapers and magazines, most of them from Sao Paulo State, were identified. The analyzed speeches were classified according to five information sources: specialists, users, authorities, protagonists and entrepreneurs. It was noted the predominance of positive articles, mainly due to the weight of the favorable speeches by authorities, cited as the most frequent in this paper. (author)

  5. The nuclear controversy as reflected in the daily press

    International Nuclear Information System (INIS)

    Buiren, S. van.

    1980-01-01

    Based on a content analysis of 2047 journal articles of the years 1974 to 1977 on conflicts over nuclear power plants (Wyhl, Brokdorf), the book intends to analyze the role of the media in present social conflicts. The book presents facts and figures concerning the information and opinions on nuclear power in five newspapers and the bias of these newspapers in favour of nuclear power or against it. According to the author, newspaper journalists have failed at least in one thing: to explain the dimensions of the conflict with regard to social policy and to give background information on their own opinions. On the other hand, the press has proved its independence: It is not an extended arm of industrial PR departments - at least not in the nuclear controversy. The greater part of the articles is in opposition to nuclear power. The development and modifications of the arguments stated by the various groups active in the nuclear controversy are analyzed in dependence of the increasingly aggressive nature of the conflict. (HP) [de

  6. Process and equipment development for hot isostatic pressing treatability study

    Energy Technology Data Exchange (ETDEWEB)

    Bateman, Ken; Wahlquist, Dennis; Malewitz, Tim

    2015-03-01

    Battelle Energy Alliance (BEA), LLC, has developed processes and equipment for a pilot-scale hot isostatic pressing (HIP) treatability study to stabilize and volume reduce radioactive calcine stored at Idaho National Laboratory (INL). In 2009, the U. S. Department of Energy signed a Record of Decision with the state of Idaho selecting HIP technology as the method to treat 5,800 yd^3 (4,400 m^3) of granular zirconia and alumina calcine produced between 1953 and 1992 as a waste byproduct of spent nuclear fuel reprocessing. Since the 1990s, a variety of radioactive and hazardous waste forms have been remotely treated using HIP within INL hot cells. To execute the remote process at INL, waste is loaded into a stainless-steel or aluminum can, which is evacuated, sealed, and placed into a HIP furnace. The HIP simultaneously heats and pressurizes the waste, reducing its volume and increasing its durability. Two 1 gal cans of calcine waste currently stored in a shielded cask were identified as candidate materials for a treatability study involving the HIP process. Equipment and materials for cask-handling and calcine transfer into INL hot cells, as well as remotely operated equipment for waste can opening, particle sizing, material blending, and HIP can loading have been designed and successfully tested. These results demonstrate BEA’s readiness for treatment of INL calcine.

  7. MASCULINITY REPRESENTATION IN THE INTERWAR LITHUANIAN PRESS ADVERTISING

    Directory of Open Access Journals (Sweden)

    Gabija Bankauskaitė-Sereikienė

    2016-10-01

    Full Text Available The analysis of this article focuses on normative interwar masculinity images. As advertising is an integral part of modern society revealing its face, the analysis is based on press advertisements collected from interwar magazines. Hegemonic features such as: a super man, a successful careerist, the man of a family, a hedonistic and narcissistic man were analysed. The analysis is focused on verbal and non-verbal expressions. The results have shown that the image of a super man was mostly related to the body and its size, ability to do a hard work. Main details – classic suit and luxury attribute such as a car usually represented a good social status and described a man as a successful careerist. It was noted that during the interwar period hegemonic masculinity was expressed by self-confidence. It was represented by a hedonistic, level-headed man images. The construct of the patriarch of the family started to be criticized during the interwar period and was slowly replaced by a new image of a careful man and husband.

  8. Chemical Composition of Iran's Pistacia atlantica Cold-Pressed Oil

    Directory of Open Access Journals (Sweden)

    M. Saber-Tehrani

    2013-01-01

    Full Text Available The lipid fraction of Pistacia atlantica seeds was extracted for the first time by means of cold-press technique and analyzed for its chemical composition. The fatty acids, sterols, triacylglycerols (TAG, tocopherols, polyphenols, and pigments were identified and their concentrations were determined by means of reversed-phase high-performance liquid chromatography (RP-HPLC and gas chromatography (GC. Because of its high content of unsaturated fatty acids, it might prove to be of value in diets and it may be used as edible cooking or salad oils or for margarine manufacture. Pistacia atlantica seed oil has the unique sterols and tocopherols content providing source of natural antioxidants. The main triacylglycerols were SLL + PLO, SOL + POO, OOLn + PLL, OOO, and SOO. This paper examined the phenolic fraction of Pistacia atlantica seed oil. Moreover, caffeic acid followed by cinnamic acid, pinoresinol, vanillin, p-Coumaric acid, ferulic acid, and o-Coumaric acid was also determined. This paper presents the first investigation of chlorophyll's and carotene's composition in Pistacia atlantica seed oil. Furthermore, pheophytin a was the major component, followed by luteoxanthin, neoxanthin, violaxanthin, lutein, lutein isomers, chlorophyll a, chlorophyll a′, and pheophytin a′ were also determined.

  9. Pronouns as Means of Impersonal Presentation in English Quality Press

    Directory of Open Access Journals (Sweden)

    Pavel Skorupa

    2017-05-01

    Full Text Available The current paper presents the analysis of pronouns as means of impersonal presentation in English quality press. The article gives the definition of the pronoun as a grammatical category and describes the use and purpose of impersonalization strategies. The data for the investigation was taken from the international English quality newspapers: The Financial Times (UK and The Wall Street Journal (US, which are the leading daily broadsheet newspapers in the UK and the USA having millions of both print and online subscribers worldwide. The articles on political, economic, and social issues were chosen on a random basis and scrutinized for pronouns as means of impersonal presentation of fact. The body of 187 cases of impersonalization chosen for the analysis were divided into groups with focus on the grammatical category they belong to. The most and least often used classes of pronouns were identified and compared. The results of the current study may be useful for editors, journalists, writers, as well as for further study of impersonalization strategies in the English language.

  10. The "sticking period" in a maximum bench press.

    Science.gov (United States)

    van den Tillaar, Roland; Ettema, Gertjan

    2010-03-01

    The purpose of this study was to examine muscle activity and three-dimensional kinematics in the ascending phase of a successful one-repetition maximum attempt in bench press for 12 recreational weight-training athletes, with special attention to the sticking period. The sticking period was defined as the first period of deceleration of the upward movement (i.e. from the highest barbell velocity until the first local lowest barbell velocity). All participants showed a sticking period during the upward movement that started about 0.2 s after the initial upward movement, and lasted about 0.9 s. Electromyography revealed that the muscle activity of the prime movers changed significantly from the pre-sticking to the sticking and post-sticking periods. A possible mechanism for the existence of the sticking period is the diminishing potentiation of the contractile elements during the upward movement together with the limited activity of the pectoral and deltoid muscles during this period.

  11. Reconstructing apology: David Cameron's Bloody Sunday apology in the press.

    Science.gov (United States)

    McNeill, Andrew; Lyons, Evanthia; Pehrson, Samuel

    2014-12-01

    While there is an acknowledgement in apology research that political apologies are highly mediated, the process of mediation itself has lacked scrutiny. This article suggests that the idea of reconstruction helps to understand how apologies are mediated and evaluated. David Cameron's apology for Bloody Sunday is examined to see how he constructs four aspects of apology: social actors, consequences, categorization, and reasons. The reconstruction of those aspects by British, Unionist, and Nationalist press along with reconstructions made by soldiers in an online forum are considered. Data analysis was informed by thematic analysis and discourse analysis which helped to explore key aspects of reconstruction and how elements of Cameron's apology are altered in subsequent mediated forms of the apology. These mediated reconstructions of the apology allowed their authors to evaluate the apology in different ways. Thus, in this article, it is suggested that the evaluation of the apology by different groups is preceded by a reconstruction of it in accordance with rhetorical goals. This illuminates the process of mediation and helps to understand divergent responses to political apologies. © 2013 The British Psychological Society.

  12. The approach of nuclear related issues by the press

    Energy Technology Data Exchange (ETDEWEB)

    Manetti, Cristiane Teixeira; Tanimoto, Katia Suemi; Hiromoto, Goro [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)], e-mail: cristianemanetti@hotmail.com, e-mail: katia_tanimoto@hotmail.com, e-mail: hiromoto@ipen.br

    2009-07-01

    Nuclear energy has always been a polemic issue, and it is usually more intensely associated, by the general public, to the risks than to the benefits from its use; in this sense, the mass media have clearly had its share of responsibility for public opinion formation. This paper presents a report on the coverage of the nuclear issue in the press, identifying the amount of negative and positive views on the subject, as well as the people involved in the process. The analysis comprises the period from February 2007 to February 2008, right after the edition of the 4th IPCC Report. From that sample, 172 texts published in widely known newspapers and magazines, most of them from Sao Paulo State, were identified. The analyzed speeches were classified according to five information sources: specialists, users, authorities, protagonists and entrepreneurs. It was noted the predominance of positive articles, mainly due to the weight of the favorable speeches by authorities, cited as the most frequent in this paper. (author)

  13. Role of the press in cold fusion saga

    International Nuclear Information System (INIS)

    Lindley, D.

    1992-01-01

    Press reports of cold-fusion discoveries in Utah and the pending publication of them in Nature magazine caught the associate editor of Nature, David Lindley, by surprise. Like most people, he had never heard of cold fusion. He learned that two papers, one from Steven Jones at Brigham Young University and one from Stanley Pons and Martin Fleischmann of the University of Utah, had been submitted to Nature and were undergoing the magazine's peer-review process. For weeks, Lindley was bombarded by reporters wanting daily progress reports. Many of the reporters considered the peer review a fuddy-duddy procedure meant primarily to impose conformity and suppress revolutionary ideas. In the end, Nature decided to publish the paper by Jones but not the one by Pons and Fleischmann. Because of the doubts cast on Pons and Fleischmann's findings, Nature's decision created no great public stir, Lindley recalls. But it did help reinforce in the authors the belief that they were heretics whom the establishment was out to destroy. Like politicians struggling at the polls, they blamed everyone but themselves, Lindley says. Above all, they blaimed the two all-time favorites - the media and the establishment

  14. Activity-Based Costing in the After Press Services Industry

    Science.gov (United States)

    Shevasuthisilp, Suntichai; Punsathitwong, Kosum

    2009-10-01

    This research was conducted to apply activity-based costing (ABC) in an after press service company in Chiang Mai province, Thailand. The company produces all of its products by one-stop service (such as coating, stitching, binding, die cutting, and gluing). All products are made to order, and have different sizes and patterns. A strategy of low price is used to compete in the marketplace. After cost analysis, the study found that the company has high overhead (36.5% of total cost). The company's problem is its use of traditional cost accounting, which has low accuracy in assigning overhead costs. If management uses this information when pricing customer orders, losses may occur because real production costs may be higher than the selling price. Therefore, the application of ABC in cost analysis can help executives receive accurate cost information; establish a sound pricing strategy; and improve the manufacturing process by determining work activities which have excessively high production costs. According to this research, 6 out of 56 items had a production cost higher than the selling price, leading to losses of 123,923 baht per year. Methods used to solve this problem were: reducing production costs; establishing suitable prices; and creating a sales promotion with lower prices for customers whose orders include processes involving unused capacity. These actions will increase overall sales of the company, and allow more efficient use of its machinery.

  15. Addressing Pressing Needs in the Development of Advanced Therapies.

    Science.gov (United States)

    Morrow, David; Ussi, Anton; Migliaccio, Giovanni

    2017-01-01

    The commercial development of advanced therapy medicinal products (ATMPs) represents great opportunity for therapeutic innovation but is beset by many challenges for its developers. Although the ATMP field continues to progress at a rapid pace, evidenced by the increasing number of clinical trials conducted over the past few years, several factors continue to complicate the introduction of ATMPs as a curative treatment for multiple disease types, by blocking their translational pathway from research to the patient. While several recent publications (Trounson and McDonald, 2015; Abou-El-Enein et al., 2016a,b) as well as an Innovative Medicines Initiative consultation (IMI, 2016) this year have highlighted the major gaps in ATMP development, with manufacturing, regulatory, and reimbursement issues at the forefront, there remains to be formulated a coherent strategy to address these by bringing the relevant stakeholders to a single forum, whose task it would be to design and execute a delta plan to alleviate the most pressing bottlenecks. This article focuses on two of the most urgent areas in need of attention in ATMP development, namely manufacturing and reimbursement, and promotes the concept of innovation-dedicated research infrastructures to support a multi-sector approach for ensuring the successful development, entry, and ensuing survival of ATMPs in the healthcare market.

  16. Addressing Pressing Needs in the Development of Advanced Therapies

    Directory of Open Access Journals (Sweden)

    David Morrow

    2017-09-01

    Full Text Available The commercial development of advanced therapy medicinal products (ATMPs represents great opportunity for therapeutic innovation but is beset by many challenges for its developers. Although the ATMP field continues to progress at a rapid pace, evidenced by the increasing number of clinical trials conducted over the past few years, several factors continue to complicate the introduction of ATMPs as a curative treatment for multiple disease types, by blocking their translational pathway from research to the patient. While several recent publications (Trounson and McDonald, 2015; Abou-El-Enein et al., 2016a,b as well as an Innovative Medicines Initiative consultation (IMI, 2016 this year have highlighted the major gaps in ATMP development, with manufacturing, regulatory, and reimbursement issues at the forefront, there remains to be formulated a coherent strategy to address these by bringing the relevant stakeholders to a single forum, whose task it would be to design and execute a delta plan to alleviate the most pressing bottlenecks. This article focuses on two of the most urgent areas in need of attention in ATMP development, namely manufacturing and reimbursement, and promotes the concept of innovation-dedicated research infrastructures to support a multi-sector approach for ensuring the successful development, entry, and ensuing survival of ATMPs in the healthcare market.

  17. A hybrid press system: Motion design and inverse kinematics issues

    Directory of Open Access Journals (Sweden)

    M. Erkan Kütük

    2016-06-01

    Full Text Available A hybrid machine (HM is a system integrating two types of motor; servo and constant velocity with a mechanism. The purpose is to make use of the energy in the system efficiently with a flexible system having more than one degree of freedom (DOF. A review is included on hybrid press systems. This study is included as a part of an industrial project used for metal forming. The system given here includes a 7 link mechanism, one of link is driven by a constant velocity motor (CV and the other is driven by a servo motor (SM. Kinematics analysis of the hybrid driven mechanism is presented here as inverse kinematics analysis. Motion design is very crucial step when using a hybrid machine. So motion design procedure is given with motion curve examples needed. Curve Fitting Toolbox (CFT in Matlab® is offered as an auxiliary method which can be successfully applied. Motion characteristics are chosen by looking at requirements taken from metal forming industry. Results are then presented herein.

  18. Representations of handicaped in the portuguese press: hegemony and emancipation

    Directory of Open Access Journals (Sweden)

    Patrícia Neca

    2012-12-01

    Full Text Available The purpose of this study is to describe and analyze what are the representations that three Portuguese general-interest newspapers - Diário de Notícias, Jornal de Notícias and Público - construct and convey about people with disabilities. The analysis was guided by the perspective of social representations, on the assumption that the views conveyed by the press are shared by society and affect the public opinion. A total of 220 articles about disabilities, published in November and December between 2004 and 2009 where analyzed. The results show that there is little questioning in the newspapers regarding issues related with disability and that there are different representations mediated by different newspapers. Diário de Notícias and Público convey hegemonic representations, in other words, don´t discuss the disability issues and show the group as homogeneous, incompetent and object of social policies, thus blocking the appearance of new representations. Jornal de Notícias convey emancipated representations, this is, opens space to the debate of the new ideas, showing disabled people as competent, mainly in articles about awareness raising and physical disability. This debate enhances the appearance of new representations. Regarding mental disability, it appears associated to the stereotype of incompetence, in all the newspapers analyzed.

  19. Effect of different pushing speeds on bench press.

    Science.gov (United States)

    Padulo, J; Mignogna, P; Mignardi, S; Tonni, F; D'Ottavio, S

    2012-05-01

    The purpose of this study was to investigate the effect on muscular strength after a 3-week training with the bench-press at a fixed pushing of 80-100% maximal speed (FPS) and self-selected pushing speed (SPS). 20 resistance-trained subjects were divided at random in 2 groups differing only regarding the pushing speed: in the FPS group (n=10) it was equal to 80-100% of the maximal speed while in the SPS group (n=10) the pushing speed was self-selected. Both groups were trained twice a week for 3 weeks with a load equal to 85% of 1RM and monitored with the encoder. Before and after the training we measured pushing speed and maximum load. Significant differences between and within the 2 groups were pointed out using a 2-way ANOVA for repeated measures. After 3 weeks a significant improvement was shown especially in the FPS group: the maximum load improved by 10.20% and the maximal speed by 2.22%, while in the SPS group the effect was <1%. This study shows that a high velocity training is required to increase the muscle strength further in subjects with a long training experience and this is possible by measuring the individual performance speed for each load. © Georg Thieme Verlag KG Stuttgart · New York.

  20. A study of pressureless microwave sintering, microwave-assisted hot press sintering and conventional hot pressing on properties of aluminium/alumina nanocomposite

    Energy Technology Data Exchange (ETDEWEB)

    Abedinzadeh, Reza; Safavi, Seyed Mohsen; Karimzadeh, Fathallah [Isfahan University, Isfahan (Iran, Islamic Republic of)

    2016-05-15

    Bulk Al/4wt-%Al{sub 2}O{sub 3} nanocomposites were prepared by consolidating nanocomposite powders using pressureless microwave sintering, microwave-assisted hot press sintering and conventional hot pressing techniques. Microstructural observations revealed that the microwave-assisted hot press sintering at different sintering temperatures of 400.deg.C and 500.deg.C resulted in more densification and smaller grain size for Al/Al{sub 2}O{sub 3} nanocomposite as compared with the conventional hot pressing. Moreover, the application of pressure in microwave sintering process led to more densification and grain growth. Mechanical properties resulting from microhardness and nanoindentation tests were also compared between three-method processed samples. It was found that the microwave-assisted hot-pressed sample exhibited higher hardness and elastic modulus in comparison with microwave-sintered and conventional hot-pressed samples. The improvement in the mechanical properties can be ascribed to lower porosity of microwave-assisted hot-pressed sample.