WorldWideScience

Sample records for preprints owp starting

  1. oWPS VERSUS cWPS

    CERN Document Server

    Mainaud Durand, H; Herty, A; Marin, A; Rude, V

    2012-01-01

    The strategy of the CLIC pre-alignment relies on Wire Positioning Sensors (WPS) measuring the radial and vertical offsets with respect to a stretched wire. A precision below 2 µm and an accuracy of 5 µm over a whole range of measurement of 10 mm per axis are required for these sensors. Two types of sensors, based on two different technologies are under development and study at CERN: the capacitive sensor (cWPS) is already in use for the monitoring of the position of the low beta triplets in the LHC and the optical sensor (oWPS) is currently under development with Open Source Instruments. The cWPS had to be upgraded in order to reach the specifications required by the CLIC alignment. The oWPS is a new development especially designed to the CLIC demands. The paper presents the two types of sensors, the developments, as well as the latest results obtained in validation tests. These two types of sensors are part of a common test setup: results of inter-comparison tests achieved on this setup are detailed.

  2. USABC Development of 12 Volt Battery for Start-Stop Application: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Tataria, H.; Gross, O.; Bae, C.; Cunningham, B.; Barnes, J. A.; Deppe, J.; Neubauer, J.

    2015-02-01

    Global automakers are accelerating the development of fuel efficient vehicles, as a part of meeting regional regulatory CO2 emissions requirements. The micro hybrid vehicles with auto start-stop functionality are considered economical solutions for the stringent European regulations. Flooded lead acid batteries were initially considered the most economical solution for idle-stop systems. However, the dynamic charge acceptance (DCA) at lower state-of-charge (SOC) was limiting the life of the batteries. While improved lead-acid batteries with AGM and VRLA features have improved battery longevity, they do not last the life of the vehicle. The United States Advanced Battery Consortium (or USABC, a consortium of GM, Ford, and Chrysler) analyzed energy storage needs for a micro hybrid automobile with start-stop capability, and with a single power source. USABC has analyzed the start-stop behaviors of many drivers and has developed the requirements for the start-stop batteries (Table 3). The testing procedures to validate the performance and longevity were standardized and published. The guideline for the cost estimates calculations have also been provided, in order to determine the value of the newly developed modules. The analysis effort resulted in a set of requirements which will help the battery manufacturers to develop a module to meet the automotive Original Equipment Manufacturers (OEM) micro hybrid vehicle requirements. Battery developers were invited to submit development proposals and two proposals were selected for 50% cost share with USABC/DOE.

  3. Preprinting Microbiology.

    Science.gov (United States)

    Schloss, Patrick D

    2017-05-23

    The field of microbiology has experienced significant growth due to transformative advances in technology and the influx of scientists driven by a curiosity to understand how microbes sustain myriad biochemical processes that maintain Earth. With this explosion in scientific output, a significant bottleneck has been the ability to rapidly disseminate new knowledge to peers and the public. Preprints have emerged as a tool that a growing number of microbiologists are using to overcome this bottleneck. Posting preprints can help to transparently recruit a more diverse pool of reviewers prior to submitting to a journal for formal peer review. Although the use of preprints is still limited in the biological sciences, early indications are that preprints are a robust tool that can complement and enhance peer-reviewed publications. As publishing moves to embrace advances in Internet technology, there are many opportunities for preprints and peer-reviewed journals to coexist in the same ecosystem. Copyright © 2017 Schloss.

  4. PC database for high energy preprint collections

    International Nuclear Information System (INIS)

    Haymaker, R.

    1985-06-01

    We describe a microcomputer database used by the high energy group to keep track of preprints in our collection. It is used as a supplement to the SLAC-SPIRES database to retrieve preprints on hand. This was designed as a low overhead system for a small group

  5. Glossary-HDSC/OWP

    Science.gov (United States)

    (CUMULATIVE DISTRIBUTION FUNCTION) - Mathematical description that completely describes frequency distribution magnitude for a given duration. FREQUENCY ANALYSIS - Process of derivation of a mathematical model that -MOMENTS - L-moments are summary statistics for probability distributions and data samples. They are

  6. The preprint debate: What are the issues?

    Science.gov (United States)

    da Silva, Jaime A Teixeira

    2018-04-01

    The debate surrounding preprints is increasing. Preprint proponents claim that preprints are a way to shore up trust in academic publishing, that they provide an additional 'quality' screen prior to traditional peer review, that they can assist with the replication crisis plaguing science in part by making negative or contradictory results public, and that they speed up the publishing process because fundamental results can be presented early, serving as timely reports for the purposes of tenure or grant funding. Preprint skeptics and critics claim that preprints may represent a risk and a danger to quality-based academic publishing because they are documents that have not been carefully and thoroughly vetted prior to their release into the public domain. Thus, academics who cite invalid, poorly vetted, or false facts could cause harm, not unlike the unscholarly 'predatory' open access movement. Feedback on work from lesser-known groups, or on less glamorous topics, may be null or worse than from traditional peer review, annulling an initial key objective of preprints. Although there is no widespread empirical evidence or data yet regarding some of these issues, academics should be aware of the ideological, financial, and political tug-of-war taking place before deciding if they wish to publish their important findings as a preprint prior or simultaneous to submitting to a regular journal for peer review.

  7. search.bioPreprint: a discovery tool for cutting edge, preprint biomedical research articles [version 2; referees: 2 approved

    Directory of Open Access Journals (Sweden)

    Carrie L. Iwema

    2016-07-01

    Full Text Available The time it takes for a completed manuscript to be published traditionally can be extremely lengthy. Article publication delay, which occurs in part due to constraints associated with peer review, can prevent the timely dissemination of critical and actionable data associated with new information on rare diseases or developing health concerns such as Zika virus. Preprint servers are open access online repositories housing preprint research articles that enable authors (1 to make their research immediately and freely available and (2 to receive commentary and peer review prior to journal submission. There is a growing movement of preprint advocates aiming to change the current journal publication and peer review system, proposing that preprints catalyze biomedical discovery, support career advancement, and improve scientific communication. While the number of articles submitted to and hosted by preprint servers are gradually increasing, there has been no simple way to identify biomedical research published in a preprint format, as they are not typically indexed and are only discoverable by directly searching the specific preprint server websites. To address this issue, we created a search engine that quickly compiles preprints from disparate host repositories and provides a one-stop search solution. Additionally, we developed a web application that bolsters the discovery of preprints by enabling each and every word or phrase appearing on any web site to be integrated with articles from preprint servers. This tool, search.bioPreprint, is publicly available at http://www.hsls.pitt.edu/resources/preprint.

  8. A Real-Time Systems Symposium Preprint.

    Science.gov (United States)

    1983-09-01

    Real - Time Systems Symposium Preprint Interim Tech...estimate of the occurence of the error. Unclassii ledSECUqITY CLASSIF’ICA T" NO MI*IA If’ inDI /’rrd erter for~~ble. ’Corrputnqg A REAL - TIME SYSTEMS SYMPOSIUM...ABSTRACT This technical report contains a preprint of a paper accepted for presentation at the REAL - TIME SYSTEMS SYMPOSIUM, Arlington,

  9. Preprint data base system at INS: INSPREP system

    International Nuclear Information System (INIS)

    Shinohara, M.; Ukai, K.; Fujiyoshi, N.

    1988-02-01

    The library at the INS (Institute for Nuclear Study) receives several tens of preprints a week from foreign and domestic laboratories and universities. These preprints are pigeonholed by making a catalog card index carried a title, authors, an accession number, classification of fields, etc. A newly arrived preprint lists is also served every week. The cataloging and weekly lists publishing works were handled with a typewriter. And then, it was very difficult and tedious to correct/check/file the index cards and to correct/check the weekly preprint lists. To make a preprint data efficiently by a computer and to refer this data base by on-line without using a index card, the INSPREP system is constructed. The INSPREP system consists of two parts. One is named a PREPINS, and is used to make a preprint data, builds a preprint data base, and publishes a weekly preprint lists. The other, called a PREP, performs an on-line retrieval for this data base. The preprint data base consists of following items such as an author, a title, an accession number, a report number, a classification field, etc. The PREPINS can be used by limited persons for security. User can search a preprint by inputting above mentioned items. The PREP adopts a menu method. Then, user can perform an on-line retrieval very easily. (author)

  10. Citation Patterns to Traditional and Electronic Preprints in the Published Literature.

    Science.gov (United States)

    Youngen, Gregory K.

    1998-01-01

    Identifies the growing importance of electronic preprints in the published literature of physics and astronomy and address several areas of concern regarding the future role of electronic preprints in scientific communication. Topics include a history of preprints in astronomy and physics; inaccuracies in preprint citations; and archival issues.…

  11. Preprint server seeks way to halt plagiarists

    CERN Multimedia

    Giles, J

    2003-01-01

    "An unusual case of plagiarism has struck ArXiv, the popular physics preprint server at Cornell University in Ithaca, New York, resulting in the withdrawal of 22 papers...The plagiarism case traces its origins to June 2002, when Yasushi Watanabe, a high-energy physicist at the Tokyo Insitute of Technology, was contacted by Ramy Noboulsi, who said he was a mathematical physicist" (1 page)

  12. Why START?

    International Nuclear Information System (INIS)

    Mendelsohn, J.

    1991-01-01

    Barring some major unexpected downturn in US-Soviet relations, it seems likely that the long-awaited Strategic Arms Reduction Talks (START) treaty will be signed sometime in 1991. Under negotiation for the past nine years, public acceptance and Senate approval of a START treaty will be facilitated by the generally less confrontational East-West relationship which has evolved over that time, by the growing constraints on the US defense budget, and by the obvious merits of the treaty itself. Not only will the nearly complete START treaty be an extremely useful and powerful arms control agreement, it is also decidedly advantageous to US security interests. First and foremost, a START treaty will cap and reduce the steady buildup of nuclear weapons that has characterized the last 30 years of the US-Soviet strategic relationship. As a result of the basic outline originally agreed to at the Reykjavik summit, START will take a 25 to 35 percent bite out of existing nuclear arsenals, impose approximately a 50 percent cut in overall Soviet ballistic missile warheads and throw-weight (lifting power or payload capacity), and produce an exact 50 percent cut in Soviet SS-18 missiles

  13. Starting out

    NARCIS (Netherlands)

    Ans Merens; Freek Bucx

    2018-01-01

    Original title: Werken aan de start Women in the Netherlands have been outperforming men in education for many years now. However, this superior educational achievement does not translate into a better position on the labour market. More women work today than in the past, but still fewer than men.

  14. Press Start

    Science.gov (United States)

    Harteveld, Casper

    This level sets the stage for the design philosophy called “Triadic Game Design” (TGD). This design philosophy can be summarized with the following sentence: it takes two to tango, but it takes three to design a meaningful game or a game with a purpose. Before the philosophy is further explained, this level will first delve into what is meant by a meaningful game or a game with a purpose. Many terms and definitions have seen the light and in this book I will specifically orient at digital games that aim to have an effect beyond the context of the game itself. Subsequently, a historical overview is given of the usage of games with a serious purpose which starts from the moment we human beings started to walk on our feet till our contemporary society. It turns out that we have been using games for all kinds of non-entertainment purposes for already quite a long time. With this introductory material in the back of our minds, I will explain the concept of TGD by means of a puzzle. After that, the protagonist of this book, the game Levee Patroller, is introduced. Based on the development of this game, the idea of TGD, which stresses to balance three different worlds, the worlds of Reality, Meaning, and Play, came into being. Interested? Then I suggest to quickly “press start!”

  15. One-shot service searches: Preprint repositories at a mouseclick

    International Nuclear Information System (INIS)

    Canessa, E.; Pastore, G.

    1996-09-01

    In this article we introduce the ICTP-International Centre for Theoretical Physics's prototype for a ''One-Shot World-Wide Preprints Search'' on the Web. This is a new centralized interface for a global search throughout the most popular scientific preprint repositories. Herein, we briefly discuss our experience with the implementation of this service and propose it as a possible alternative solution to the problem of getting access to the information without being either overloaded with lots of new documents or not being informed at all. (author). 13 refs, 3 figs

  16. One-shot service searches: Preprint repositories at a mouseclick

    Energy Technology Data Exchange (ETDEWEB)

    Canessa, E [International Centre for Theoretical Physics, Trieste (Italy); Pastore, G [Trieste Univ., Trieste (Italy). Dipt. di Fisica

    1996-09-01

    In this article we introduce the ICTP-International Centre for Theoretical Physics`s prototype for a ``One-Shot World-Wide Preprints Search`` on the Web. This is a new centralized interface for a global search throughout the most popular scientific preprint repositories. Herein, we briefly discuss our experience with the implementation of this service and propose it as a possible alternative solution to the problem of getting access to the information without being either overloaded with lots of new documents or not being informed at all. (author). 13 refs, 3 figs.

  17. to start

    Indian Academy of Sciences (India)

    Click here to start. Table of contents. Slide 1 · Slide 2 · Slide 3 · Slide 4 · Slide 5 · Slide 6 · Slide 7 · Slide 8 · Slide 9 · Slide 10 · Slide 11 · Slide 12 · Slide 13 · Slide 14 · Slide 15 · Slide 16 · Slide 17 · Slide 18 · Slide 19 · Slide 20 · Slide 21 · Slide 22 · Slide 23 · Slide 24 · Slide 25 · Slide 26 · Slide 27 · Slide 28 · Slide 29 · Slide 30.

  18. Starting electronics

    CERN Document Server

    Brindley, Keith

    2005-01-01

    Starting Electronics is unrivalled as a highly practical introduction for hobbyists, students and technicians. Keith Brindley introduces readers to the functions of the main component types, their uses, and the basic principles of building and designing electronic circuits. Breadboard layouts make this very much a ready-to-run book for the experimenter; and the use of multimeter, but not oscilloscopes, puts this practical exploration of electronics within reach of every home enthusiast's pocket. The third edition has kept the simplicity and clarity of the original. New material

  19. Preprint WebVRGIS Based Traffic Analysis and Visualization System

    OpenAIRE

    Li, Xiaoming; Lv, Zhihan; Wang, Weixi; Zhang, Baoyun; Hu, Jinxing; Yin, Ling; Feng, Shengzhong

    2015-01-01

    This is the preprint version of our paper on Advances in Engineering Software. With several characteristics, such as large scale, diverse predictability and timeliness, the city traffic data falls in the range of definition of Big Data. A Virtual Reality GIS based traffic analysis and visualization system is proposed as a promising and inspiring approach to manage and develop traffic big data. In addition to the basic GIS interaction functions, the proposed system also includes some intellige...

  20. The prehistory of biology preprints: A forgotten experiment from the 1960s.

    Directory of Open Access Journals (Sweden)

    Matthew Cobb

    2017-11-01

    Full Text Available In 1961, the National Institutes of Health (NIH began to circulate biological preprints in a forgotten experiment called the Information Exchange Groups (IEGs. This system eventually attracted over 3,600 participants and saw the production of over 2,500 different documents, but by 1967, it was effectively shut down following the refusal of journals to accept articles that had been circulated as preprints. This article charts the rise and fall of the IEGs and explores the parallels with the 1990s and the biomedical preprint movement of today.

  1. The prehistory of biology preprints: A forgotten experiment from the 1960s.

    Science.gov (United States)

    Cobb, Matthew

    2017-11-01

    In 1961, the National Institutes of Health (NIH) began to circulate biological preprints in a forgotten experiment called the Information Exchange Groups (IEGs). This system eventually attracted over 3,600 participants and saw the production of over 2,500 different documents, but by 1967, it was effectively shut down following the refusal of journals to accept articles that had been circulated as preprints. This article charts the rise and fall of the IEGs and explores the parallels with the 1990s and the biomedical preprint movement of today.

  2. Preprints in biomedicine: alternative or complement to the traditional model of publication?

    Science.gov (United States)

    Aquino-Jarquin, Guillermo; Valencia-Reyes, Josefina de Monserrat; Silva-Carmona, Abraham; Granados-Riverón, Javier Tadeo

    2018-01-01

    The peer-review system has allowed the quality control of the manuscripts submitted for publication to scientific journals for over three centuries. However, due to its relative slowness and other drawbacks, some researchers, mainly in the areas of Physics and Mathematics, started some decades ago to propagate, by electronic means, manuscripts not yet submitted to a journal for formal publication. The dissemination of this practice led to the establishment of permanent repositories like ArXiv, to which preprints can be sent to be published whitou charge, allowing also the search and download of the works they contain with no payment required from the reader. In biomedical sciences, the adoption of the system has been slower than in the exact sciences and previous attempts like e-biomed, Netprints, and Nature Precedings did not prosper. A new generation of repositories like bioRXiv, inspired by ArXiv, seems to enjoy an increasing acceptance among biomedical researchers. Here, we discuss the potential role of this emerging system to establish discovery priority in biomedicine and to improve manuscripts before they are submitted to scientific journals besides other applications which could be implemented in the extent that the model becomes more popular. Copyright: © 2018 SecretarÍa de Salud.

  3. Optimizing the design of preprinted orders for ambulatory chemotherapy: combining oncology, human factors, and graphic design.

    Science.gov (United States)

    Jeon, Jennifer; White, Rachel E; Hunt, Richard G; Cassano-Piché, Andrea L; Easty, Anthony C

    2012-03-01

    To establish a set of guidelines for developing ambulatory chemotherapy preprinted orders. Multiple methods were used to develop the preprinted order guidelines. These included (A) a comprehensive literature review and an environmental scan; (B) analyses of field study observations and incident reports; (C) critical review of evidence from the literature and the field study observation analyses; (D) review of the draft guidelines by a clinical advisory group; and (E) collaboration with graphic designers to develop sample preprinted orders, refine the design guidelines, and format the resulting content. The Guidelines for Developing Ambulatory Chemotherapy Preprinted Orders, which consist of guidance on the design process, content, and graphic design elements of ambulatory chemotherapy preprinted orders, have been established. Health care is a safety critical, dynamic, and complex sociotechnical system. Identifying safety risks in such a system and effectively addressing them often require the expertise of multiple disciplines. This study illustrates how human factors professionals, clinicians, and designers can leverage each other's expertise to uncover commonly overlooked patient safety hazards and to provide health care professionals with innovative, practical, and user-centered tools to minimize those hazards.

  4. Lean start-up

    DEFF Research Database (Denmark)

    Rasmussen, Erik Stavnsager; Tanev, Stoyan

    2016-01-01

    The risk of launching new products and starting new firms is known to be extremely high. The Lean Start-up approach is a way of reducing these risks and enhancing the chances for success by validating the products and services in the market with customers before launching it in full scale. The ma...... and the final business model. In other words: The start-up must first nail the problem together with the customers, then develop the solution and test, and then in the end scale it to a full-grown business model.......The risk of launching new products and starting new firms is known to be extremely high. The Lean Start-up approach is a way of reducing these risks and enhancing the chances for success by validating the products and services in the market with customers before launching it in full scale. The main...

  5. Starting an aphasia center?

    Science.gov (United States)

    Elman, Roberta J

    2011-08-01

    Starting an aphasia center can be an enormous challenge. This article provides initial issues to review and consider when deciding whether starting a new organization is right for you. Determining the need for the program in your community, the best size and possible affiliation for the organization, and available resources, as well as developing a business plan, marketing the program, and building awareness in the community, are some of the factors that are discussed. Specific examples related to starting the Aphasia Center of California are provided. © Thieme Medical Publishers.

  6. Early Head Start Evaluation

    Data.gov (United States)

    U.S. Department of Health & Human Services — Longitudinal information from an evaluation where children were randomly assigned to Early Head Start or community services as usual;direct assessments and...

  7. FEMA DFIRM Station Start

    Data.gov (United States)

    Minnesota Department of Natural Resources — This table contains information about station starting locations. These locations indicate the reference point that was used as the origin for distance measurements...

  8. Head Start Impact Study

    Data.gov (United States)

    U.S. Department of Health & Human Services — Nationally representative, longitudinal information from an evaluation where children were randomly assigned to Head Start or community services as usual;direct...

  9. Getting started with Unity

    CERN Document Server

    Felicia, Patrick

    2013-01-01

    Getting Started with Unity is written in an easy-to-follow tutorial format.""Getting Started with Unity"" is for[ 3D game developers[/color] who would like to learn how to use Unity3D and become familiar with its core features. This book is also suitable for intermediate users who would like to improve their skills. No prior knowledge of Unity3D is required.

  10. Getting started with Go

    CERN Multimedia

    CERN. Geneva

    2015-01-01

    No, not the Chinese boardgame, the programming language that ironically Google made difficult to google for. You may have heard of Golang, and are wondering whether you should learn it. The answer is that of course you should, and this talk should explain why and point you at the best resources to get started.

  11. The renaissance starts here

    International Nuclear Information System (INIS)

    Nedderman, John.

    1997-01-01

    The Asian Pacific Basin region has the highest rate of growth of anywhere in the world and its need for electricity is staggering. This is leading, noted a senior Korean official speaking at the 10th Pacific Basin Nuclear Conference, to a ''renaissance of nuclear power'' in Asia. Judging by the optimism in evidence at the conference, perhaps it has already started. (Author)

  12. Smart Start Evaluation Plan.

    Science.gov (United States)

    Bryant, Donna; Burchinal, Margaret; Buysse, Virginia; Kotch, Jonathan; Maxwell, Kelly; Neenan, Peter; Noblit, George; Orthner, Dennis; Peisner-Feinberg, Ellen; Telfair, Joseph

    Smart Start is North Carolina's partnership between state government and local leaders, service providers, and families to better serve children under 6 years of age and their families. This report describes the comprehensive plan to evaluate the state and local goals and objectives of the program, focusing on the components addressing the…

  13. ATLAS starts moving in

    CERN Multimedia

    2004-01-01

    The first large active detector component was lowered into the ATLAS cavern on 1 March. It consisted of the 8 modules forming the lower part of the central barrel of the tile hadronic calorimeter. The work of assembling the barrel, which comprises 64 modules, started the following day.

  14. Getting started with UDOO

    CERN Document Server

    Palazzetti, Emanuele

    2015-01-01

    If you are an Android developer who wants to learn how to use UDOO to build Android applications that are capable of interacting with their surrounding environment, then this book is ideal for you. Learning UDOO is the next great step to start building your first real-world prototypes powered by the Android operating system.

  15. Starting up the upstarts.

    Science.gov (United States)

    Greene, J

    1997-12-20

    Venture capitalists pour $1 billion a year into health care--and that investment may be the most overlooked indicator of new business opportunities. Signs show that companies focused on consolidation and cost-cutting are off the A list for risk capital. Instead, venture capitalists are targeting start-ups that save money on the front lines by truly managing care.

  16. Getting started with Simulink

    CERN Document Server

    Zamboni, Luca

    2013-01-01

    This practical and easy-to-understand learning tutorial is one big exciting exercise for students and engineers that are always short on their schedules and want to regain some lost time with the help of Simulink.This book is aimed at students and engineers who need a quick start with Simulink. Though it's not required in order to understand how Simulink works, knowledge of physics will help the reader to understand the exercises described.

  17. Getting started with JUCE

    CERN Document Server

    Robinson, Martin

    2013-01-01

    his book is a fast-paced, practical guide full of step-by-step examples which are easy to follow and implement.This book is for programmers with a basic grasp of C++. The examples start at a basic level, making few assumptions beyond fundamental C++ concepts. Those without any experience with C++ should be able to follow and construct the examples, although you may need further support to understand the fundamental concepts.

  18. Getting started with Hazelcast

    CERN Document Server

    Johns, Mat

    2013-01-01

    Written as a step-by-step guide, Getting Started with Hazelcast will teach you all you need to know to make your application data scalable.This book is a great introduction for Java developers, software architects, or developers looking to enable scalable and agile data within their applications. You should have programming knowledge of Java and a general familiarity with concepts like data caching and clustering.

  19. Start-up procedure

    International Nuclear Information System (INIS)

    Marchl, A.; Krebs, W.D.; Aleite, W.

    1975-01-01

    The start-up procedure will be shown on a pressurized water reactor, although most of the activities will occur similarly in other reactor types. The commissioning time can be divided into 5 sections, the phases A to E together lasting 26 months. Subsequently there are a test run of one month and the handling-over of the plant to the operator. A survey of the commissioning sections with several important main events is shown. (orig./TK) [de

  20. Jump Starting Entrepreneurship

    DEFF Research Database (Denmark)

    Burcharth, Ana; Smith, Pernille; Frederiksen, Lars

    How do laid-off employees become entrepreneurs after receiving a dream start into self-employment? This question is relevant for policy makers and entrepreneurship researchers alike since it raises the possibility of a reverse entrepreneurial opportunity, in which the chance of becoming an entrep......How do laid-off employees become entrepreneurs after receiving a dream start into self-employment? This question is relevant for policy makers and entrepreneurship researchers alike since it raises the possibility of a reverse entrepreneurial opportunity, in which the chance of becoming...... an entrepreneur emerges before the discovery of a profitable opportunity. We empirically examine this question on the unique setting of a corporate entrepreneurship program. In the midst of a corporate crisis, Nokia supported laid-off employees to start their own ventures under favorable conditions. We...... persevered in their endeavors and eventually became comfortable with their new career prospects. We discuss the psychological factors that impact career transition after organizational closure and theorize weather they encourage or discourage entrepreneurship....

  1. Preprint Traffic Management and Forecasting System Based on 3D GIS

    OpenAIRE

    Li, Xiaoming; Lv, Zhihan; Hu, Jinxing; Zhang, Baoyun; Yin, Ling; Zhong, Chen; Wang, Weixi; Feng, Shengzhong

    2015-01-01

    This is the preprint version of our paper on 2015 15th IEEE/ACM International Symposium on Cluster, Cloud and Grid Computing (CCGrid). This paper takes Shenzhen Futian comprehensive transportation junction as the case, and makes use of continuous multiple real-time dynamic traffic information to carry out monitoring and analysis on spatial and temporal distribution of passenger flow under different means of transportation and service capacity of junction from multi-dimensional space-time pers...

  2. The virtual library in action: Collaborative international control of high-energy physics pre-print

    International Nuclear Information System (INIS)

    Kreitz, P.A.; Addis, L.; Galic, H.; Johnson, T.

    1996-02-01

    This paper will discuss how control of the grey literature in high-energy physics pre-prints developed through a collaborative effort of librarians and physicists. It will highlight the critical steps in the development process and describe one model of a rapidly evolving virtual library for high-energy physics information. In conclusion, this paper will extend this physics model to other areas of grey literature management

  3. A Study of Stress Distribution in Layered and Gradient Tribological Coatings (Preprint)

    Science.gov (United States)

    2006-11-01

    FG) Ti/TiC coating design. On the top of the 440C stainless steel substrate, α-Ti is added as a bond layer with 50nm thickness to improve the... stainless steel substrate and the rigid spherical indenter was performed. Figure 5 (a) shows the normalized Hertzian point contact pressure distribution...AFRL-ML-WP-TP-2007-402 A STUDY OF STRESS DISTRIBUTION IN LAYERED AND GRADIENT TRIBOLOGICAL COATINGS (PREPRINT) Young Sup Kang, Shashi K

  4. PRODUCTION TECHNICS AT GRAPHIC DESIGN EDUCATION AND THE NECCESSITY OF PREPARATION KNOWLEDGE OF PRE-PRINTING

    OpenAIRE

    CEYLAN, İbrahim Gökhan

    2015-01-01

    It is neccessary to teach the knowledge of production technics and pre-printing preparations besides the knowledge of developing creativity and aesthetic concerns in order to educate the designers to fullfill the needs of the sector totally at graphic design education. The printed materials prepared by the graphic designer should be evaluated in proper criterias ıf the materials are to be printed. Graphic designers should have the knowledge of the required knowledge of the area in order to me...

  5. Customizable pre-printed consent forms: a solution in light of the Montgomery ruling.

    Science.gov (United States)

    Owen, Deborah; Aresti, Nick; Mulligan, Alex; Kosuge, Dennis

    2018-02-02

    This article presents an audit cycle supported quality improvement project addressing best practice in the consent process for lower limb arthroplasty which takes into account the new standard in surgical consent and the importance of material risks. 50 consecutive total hip and total knee replacement consent forms over a 3-month period were reviewed for legibility and completeness. Following the introduction of a new, pre-printed but customizable consent form the review process was repeated. The introduction of a customizable, pre-printed consent form that can be adjusted to reflect the individualized material risks of each patient increased legibility, reduced inappropriate human error variation and abolished the use of abbreviations and medical jargon. When used as part of an extended consent process, the authors feel that the use of pre-printed but customizable consent forms improves legibility, completeness and consistency and also provides the ability to highlight those complications that are of particular importance for that patient to satisfy the new accepted standard in surgical consent.

  6. En god start

    DEFF Research Database (Denmark)

    Sievertsen, Hans Henrik

    I Danmark er det muligt at afvige fra reglen om, at barnet skal starte i skole det kalenderår, hvor barnet fylder 6 år. Det gør 10-15 procent af en årgang, mens 80-90 procent af børnene følger normen, og 2-3 procent starter i skole et år tidligere end normen, viser en analyse baseret på børn født i...

  7. Getting Started with Processing

    CERN Document Server

    Reas, Casey

    2010-01-01

    Learn computer programming the easy way with Processing, a simple language that lets you use code to create drawings, animation, and interactive graphics. Programming courses usually start with theory, but this book lets you jump right into creative and fun projects. It's ideal for anyone who wants to learn basic programming, and serves as a simple introduction to graphics for people with some programming skills. Written by the founders of Processing, this book takes you through the learning process one step at a time to help you grasp core programming concepts. You'll learn how to sketch wi

  8. Getting started with Arduino

    CERN Document Server

    Banzi, Massimo

    2011-01-01

    Arduino is the open-source electronics prototyping platform that's taken the design and hobbyist world by storm. This thorough introduction, updated for Arduino 1.0, gives you lots of ideas for projects and helps you work with them right away. From getting organized to putting the final touches on your prototype, all the information you need is here! Inside, you'll learn about: Interaction design and physical computingThe Arduino hardware and software development environmentBasics of electricity and electronicsPrototyping on a solderless breadboardDrawing a schematic diagram Getting started

  9. Getting Started with Netduino

    CERN Document Server

    Walker, Chris

    2012-01-01

    Start building electronics projects with Netduino, the popular open source hardware platform that's captured the imagination of makers and hobbyists worldwide. This easy-to-follow book provides the step-by-step guidance you need to experiment with Netduino and the .NET Micro Framework. Through a set of simple projects, you'll learn how to create electronic gadgets-including networked devices that communicate over TCP/IP. Along the way, hobbyists will pick up the basics of .NET programming, and programmers will discover how to work with electronics and microcontrollers. Follow the projects in

  10. A Weakest-Link Approach for Fatigue Limit of 30CrNiMo8 Steels (Preprint)

    Science.gov (United States)

    2011-03-01

    34Application of a Weakest-Link Concept to the Fatigue Limit of the Bearing Steel Sae 52100 in a Bainitic Condition," Fatigue and Fracture of...AFRL-RX-WP-TP-2011-4206 A WEAKEST-LINK APPROACH FOR FATIGUE LIMIT OF 30CrNiMo8 STEELS (PREPRINT) S. Ekwaro-Osire and H.V. Kulkarni Texas...2011 4. TITLE AND SUBTITLE A WEAKEST-LINK APPROACH FOR FATIGUE LIMIT OF 30CrNiMo8 STEELS (PREPRINT) 5a. CONTRACT NUMBER In-house 5b. GRANT

  11. Starting physiology: bioelectrogenesis.

    Science.gov (United States)

    Baptista, Vander

    2015-12-01

    From a Cartesian perspective of rational analysis, the electric potential difference across the cell membrane is one of the fundamental concepts for the study of physiology. Unfortunately, undergraduate students often struggle to understand the genesis of this energy gradient, which makes the teaching activity a hard task for the instructor. The topic of bioelectrogenesis encompasses multidisciplinary concepts, involves several mechanisms, and is a dynamic process, i.e., it never turns off during the lifetime of the cell. Therefore, to improve the transmission and acquisition of knowledge in this field, I present an alternative didactic model. The design of the model assumes that it is possible to build, in a series of sequential steps, an assembly of proteins within the membrane of an isolated cell in a simulated electrophysiology experiment. Initially, no proteins are inserted in the membrane and the cell is at a baseline energy state; the extracellular and intracellular fluids are at thermodynamic equilibrium. Students are guided through a sequence of four steps that add key membrane transport proteins to the model cell. The model is simple at the start and becomes progressively more complex, finally producing transmembrane chemical and electrical gradients. I believe that this didactic approach helps instructors with a more efficient tool for the teaching of the mechanisms of resting membrane potential while helping students avoid common difficulties that may be encountered when learning this topic. Copyright © 2015 The American Physiological Society.

  12. LEP dismantling starts

    CERN Multimedia

    2000-01-01

    Since the end of November, various teams have been getting stuck into dismantling the LEP accelerator and its four experiments. After making the installations safe, the dismantling and removal of 40,000 tonnes of equipment is underway. Down in the tunnel, it is a solemn moment. It is 10 o'clock on 13 December and Daniel Regin, one of those heading the dismantling work, moves in on a magnet, armed with a hydraulic machine. Surrounded by teams gathered there for a course in dismantling, he makes the first cut into LEP. The great deconstruction has begun. In little over than a year, the accelerator will have been cleared away to make room for its successor, the LHC. The start of the operation goes back to 27 November. Because before setting about the machine with hydraulic shears and monkey wrenches, LEP had first to be made safe - it was important to make sure the machine could be taken apart without risk. All the SPS beam injection systems to LEP were cut off. The fluids used for cooling the magnets and superc...

  13. An impressive start

    CERN Multimedia

    2011-01-01

    This has been an excellent week for the LHC, with a succession of fills rapidly increasing the number of proton bunches to 194 per beam. This has allowed the experiments to reach a peak luminosity of 2.5 × 1032 cm-2s-1, thereby surpassing the record for 2010 where we reached 2.0 × 1032 cm-2s-1. At the time of writing, the integrated luminosity delivered by the LHC in 2011 is around 28 inverse picobarns, which is already more than half of the total 2010 dataset.   These are impressive numbers, but what impresses me most is how quickly the LHC operators are now able to turn the machine around between fills, and how well LHC running has been incorporated into the overall operation of CERN’s accelerator complex. The flexibility of the LHC was illustrated on Thursday when we started a short phase of running at 1.38 TeV per beam, equivalent to the energy-per-nucleon of a lead-ion run. This lower energy data will be used by the experiments, in particular by ALICE, to compare...

  14. ATLAS starts moving in

    CERN Multimedia

    Della Mussia, S

    2004-01-01

    The first large active detector component was lowered into the ATLAS cavern on 1st March. It consisted of the 8 modules forming the lower part of the central barrel of the tile hadronic calorimeter. The work of assembling the barrel, which comprises 64 modules, started the following day. Two road trailers each with 64 wheels, positioned side by side. This was the solution chosen to transport the lower part of the central barrel of ATLAS' tile hadronic calorimeter from Building 185 to the PX16 shaft at Point 1 (see Figure 1). The transportation, and then the installation of the component in the experimental cavern, which took place over three days were, to say the least, rather spectacular. On 25 February, the component, consisting of eight 6-metre modules, was loaded on to the trailers. The segment of the barrel was transported on a steel support so that it wouldn't move an inch during the journey. On 26 February, once all the necessary safety checks had been carried out, the convoy was able to leave Buildi...

  15. From Head Start to Sure Start: Reflections on Policy Transfer

    Science.gov (United States)

    Welshman, John

    2010-01-01

    This article uses the history of debates over the US Head Start programme (1965), Early Head Start (1994) and the UK Sure Start initiative (1998), as a window on to policy transfer. In all the three, the aim was that early intervention could offer a means of boosting children's educational attainment and of countering the wider effects of poverty…

  16. School Starting Age and Crime

    DEFF Research Database (Denmark)

    Landersø, Rasmus; Nielsen, Helena Skyt; Simonsen, Marianne

    This paper investigates the effects of school starting age on crime while relying on variation in school starting age induced by administrative rules; we exploit that Danish children typically start first grade in the calendar year they turn seven, which gives rise to a discontinuity in children......’s school starting age. Analyses are carried out using register-based Danish data. We find that higher age at school start lowers the propensity to commit crime, but that this reduction is caused by incapacitation while human capital accumulation is unaffected. Importantly, we also find that the individuals...

  17. Later Start, Longer Sleep: Implications of Middle School Start Times

    Science.gov (United States)

    Temkin, Deborah A.; Princiotta, Daniel; Ryberg, Renee; Lewin, Daniel S.

    2018-01-01

    Background: Although adolescents generally get less than the recommended 9 hours of sleep per night, research and effort to delay school start times have generally focused on high schools. This study assesses the relation between school start times and sleep in middle school students while accounting for potentially confounding demographic…

  18. Tips for Starting Physical Activity

    Science.gov (United States)

    ... Legislative Information Advisory & Coordinating Committees Strategic Plans & Reports Research Areas FAQs ... Starting Physical Activity Related Topics Section Navigation Tips to Help You Get Active ...

  19. Scheduling with target start times

    NARCIS (Netherlands)

    Hoogeveen, J.A.; Velde, van de S.L.; Klein Haneveld, W.K.; Vrieze, O.J.; Kallenberg, L.C.M.

    1997-01-01

    We address the single-machine problem of scheduling n independent jobs subject to target start times. Target start times are essentially release times that may be violated at a certain cost. The goal is to minimize an objective function that is composed of total completion time and maximum

  20. Psychiatric Advance Directives: Getting Started

    Science.gov (United States)

    ... News Legal Issues Search for: About PADs A psychiatric advance directive (PAD) is a legal document that ... decisions during a mental health crisis. Getting Started Psychiatric advance directives (PADs) are relatively new legal instruments ...

  1. STARTing Again: What Happens After START I Expires?

    International Nuclear Information System (INIS)

    Mladineo, Stephen V.; Durbin, Karyn R.; Eastman, Christina M.

    2007-01-01

    The Strategic Arms Reduction Treaty (START I), a seminal arms control agreement that substantially reduced the levels of deployed strategic nuclear arms in the United States and Russia, will expire in December 2009. At this time, it is unclear what - if anything - will replace it. While the treaty remains relevant, more than a simple extension is appropriate. Instead the authors advocate for a successor regime that builds on the START I legacy but does not rely on the traditional tools of arms control. This paper examines the strategic context in which a successor regime would be developed and proposes several recommendations for future action

  2. Note on: Considering the Case for Biodiversity Cycles: Reexamining the Evidence for Periodicity in the Fossil Record, by Lieberman and Melott, arXiv preprint 0704.2896

    OpenAIRE

    Omerbashich, M.

    2007-01-01

    Lieberman and Melott built their recent arXiv preprint 0704.2896 on my published paper and (a preprint of) a subsequent comment by Liebermans associate Cornette. But had this group waited for the Cornette comment to actually appear in print together with the expected Reply, they would have learned that his comment exposes Cornettes confusion that likely was due to journal misprint of my figure. Thus 0704.2896 is baseless. Despite receiving the extended Reply with Errata, these authors still f...

  3. Start Where Your Students Are

    Science.gov (United States)

    Jackson, Robyn R.

    2010-01-01

    Starting where your students are means understanding how currencies are negotiated and traded in the classroom. Any behavior that students use to acquire the knowledge and skills needed in the classroom functions as currency. Teachers communicate the kinds of currencies they accept in their classrooms, such as getting good grades; students do…

  4. Start-up of Rapsodie

    International Nuclear Information System (INIS)

    Pontier, R.

    1967-01-01

    After giving a general description of Rapsodie this report presents the conditions in which the start-up occurred and in which the tests were carried out. A chronological account is given of the operations and of the main events which occurred. The modifications made to the reactor during this period are described and a synthesis of the results obtained is presented. (author) [fr

  5. When to Start Antiretroviral Therapy

    Science.gov (United States)

    ... illnesses and coinfections Recent HIV infection Pregnancy All pregnant women with HIV should take HIV medicines to prevent mother-to- ... protect the health of the pregnant woman. All pregnant women with HIV should start taking HIV medicines as soon as ...

  6. Head Start Center Design Guide.

    Science.gov (United States)

    Administration for Children, Youth, and Families (DHHS), Washington, DC. Head Start Bureau.

    This guide contains suggested criteria for planning, designing, and renovating Head Start centers so that they are safe, child-oriented, developmentally appropriate, beautiful, environmentally sensitive, and functional. The content is based on the U.S. General Services Administration's Child Care Center Design Guide, PBS-P140, which was intended…

  7. Using DOE Commercial Reference Buildings for Simulation Studies: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Field, K.; Deru, M.; Studer, D.

    2010-08-01

    The U.S. Department of Energy developed 256 EnergyPlus models for use in studies that aim to characterize about 70% of the U.S. commercial building stock. Sixteen building types - including restaurants, health care, schools, offices, supermarkets, retail, lodging, and warehouses - are modeled across 16 cities to represent the diversity of U.S. climate zones. Weighting factors have been developed to combine the models in proportions similar to those of the McGraw-Hill Construction Projects Starts Database for 2003-2007. This paper reviews the development and contents of these models and their applications in simulation studies.

  8. Getting started with Drupal commerce

    CERN Document Server

    Jones, Richard

    2013-01-01

    A simple yet concise step-by-step tutorial that starts from scratch and builds up your knowledge with focused examples that will enable you to set up and run an e-commerce website.This book is for beginners and will take you through the installation and configuration of Drupal Commerce from scratch, but some familiarity with Drupal 7 will be an advantage. All examples are based on development on a local computer - you do not need a hosted Drupal environment.

  9. Getting started with Twitter Flight

    CERN Document Server

    Hamshere, Tom

    2013-01-01

    Getting Started with Twitter Flight is written with the intention to educate the readers, helping them learn how to build modular powerful applications with Flight, Twitter's cutting-edge JavaScript framework.This book is for anyone with a foundation in JavaScript who wants to build web applications. Flight is quick and easy to learn, built on technologies you already understand such as the DOM, events, and jQuery.

  10. School start times for adolescents.

    Science.gov (United States)

    2014-09-01

    The American Academy of Pediatrics recognizes insufficient sleep in adolescents as an important public health issue that significantly affects the health and safety, as well as the academic success, of our nation's middle and high school students. Although a number of factors, including biological changes in sleep associated with puberty, lifestyle choices, and academic demands, negatively affect middle and high school students' ability to obtain sufficient sleep, the evidence strongly implicates earlier school start times (ie, before 8:30 am) as a key modifiable contributor to insufficient sleep, as well as circadian rhythm disruption, in this population. Furthermore, a substantial body of research has now demonstrated that delaying school start times is an effective countermeasure to chronic sleep loss and has a wide range of potential benefits to students with regard to physical and mental health, safety, and academic achievement. The American Academy of Pediatrics strongly supports the efforts of school districts to optimize sleep in students and urges high schools and middle schools to aim for start times that allow students the opportunity to achieve optimal levels of sleep (8.5-9.5 hours) and to improve physical (eg, reduced obesity risk) and mental (eg, lower rates of depression) health, safety (eg, drowsy driving crashes), academic performance, and quality of life. Copyright © 2014 by the American Academy of Pediatrics.

  11. Getting Started with Hibernate 3

    CERN Document Server

    Elliott, James

    2008-01-01

    Hibernate has clearly arrived. Are you ready to benefit from its simple way of working with relational databases as Java objects? This PDF updates the introductory material from the award-winning Hibernate: A Developer's Notebook to teach you how to jump right in and get productive with the current release of Hibernate. You'll be walked through the ins and outs of setting up Hibernate and some related tools that make it easier to use--and that may give you new ideas about how to store information in your Java programs. In short, this PDF gives you exactly the information you need to start u

  12. Starting of nuclear power stations

    International Nuclear Information System (INIS)

    Kotyza, V.

    1988-01-01

    The procedure is briefly characterized of jobs in nuclear power plant start-up and the differences are pointed out from those used in conventional power generation. Pressure tests are described oriented to tightness, tests of the secondary circuit and of the individual nodes and facilities. The possibility is shown of increased efficiency of such jobs on an example of the hydraulic tests of the second unit of the Dukovany nuclear power plant where the second and the third stages were combined in the so-colled integrated hydraulic test. (Z.M.). 5 figs

  13. Getting started With Amazon Redshift

    CERN Document Server

    Bauer, Stefan

    2013-01-01

    Getting Started With Amazon Redshift is a step-by-step, practical guide to the world of Redshift. Learn to load, manage, and query data on Redshift.This book is for CIOs, enterprise architects, developers, and anyone else who needs to get familiar with RedShift. The CIO will gain an understanding of what their technical staff is working on; the technical implementation personnel will get an in-depth view of the technology, and what it will take to implement their own solutions.

  14. Predicting emergency diesel starting performance

    International Nuclear Information System (INIS)

    DeBey, T.M.

    1989-01-01

    The US Department of Energy effort to extend the operational lives of commercial nuclear power plants has examined methods for predicting the performance of specific equipment. This effort focuses on performance prediction as a means for reducing equipment surveillance, maintenance, and outages. Realizing these goals will result in nuclear plants that are more reliable, have lower maintenance costs, and have longer lives. This paper describes a monitoring system that has been developed to predict starting performance in emergency diesels. A prototype system has been built and tested on an engine at Sandia National Laboratories. 2 refs

  15. Starting a nursing consultation practice.

    Science.gov (United States)

    Schulmeister, L

    1999-03-01

    Because the clinical nurse specialist (CNS) role has been changed or eliminated in many hospital organizations, many CNSs in career transition are considering establishing collaborative or independent nursing consultation practices. Opportunities for consultants exist in diverse practice settings and specialties. Before starting a consultation practice, the CNS should carefully examine goals, identify resources, and begin contacting potential referral sources. He or she must also decide what form of business organization to establish and write a business plan to solidify ideas and prepare for the unexpected. Most CNS consultants rely on personal savings to cover initial business and personal expenses, and many continue working as a CNS until the consultation practice is established. Fees can be set based on community standards, what the market will bear, desired projected income, or a third-party payor's fee schedule. The consultation practice can be marketed by word of mouth, inexpensive advertising techniques such as distributing flyers and business cards, direct mall, and media advertising. In today's healthcare marketplace, opportunities abound for the CNS risk-taker interested in starting a nursing consultation practice.

  16. The start of the harvest

    CERN Multimedia

    2011-01-01

    The first major particle physics summer conference has just started this week in Grenoble. After the Quark-Matter conference, the Europhysics Conference on High-Energy Physics marks the start of a promising harvest for the LHC experiments.   For the first time, the collaborations will be presenting their latest results based on all luminosity taken until end of June, which will provide more precise measurements in many areas. Thanks to the excellent performance of the LHC, the experiments have already accumulated a substantial quantity of data allowing them to push back the known limits and refine measurements in many fields ranging from b physics to the search for the Higgs boson and for dark matter. At the time of writing, the LHC collaborations are about to present these new results in an energy range which has never previously been explored. I have congratulated all the teams involved in getting the LHC into operation in record time with great efficiency. Today I would like to acknowledge the...

  17. Assessment of New Approaches in Geothermal Exploration Decision Making: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Akar, S.; Young, K. R.

    2015-02-01

    Geothermal exploration projects have significant amount of risk associated with uncertainties encountered in the discovery of the geothermal resource. Understanding when and how to proceed in an exploration program, and when to walk away from a site, are two of the largest challenges for increased geothermal deployment. Current methodologies for exploration decision making is left to subjective by subjective expert opinion which can be incorrectly biased by expertise (e.g. geochemistry, geophysics), geographic location of focus, and the assumed conceptual model. The aim of this project is to develop a methodology for more objective geothermal exploration decision making at a given location, including go-no-go decision points to help developers and investors decide when to give up on a location. In this scope, two different approaches are investigated: 1) value of information analysis (VOIA) which is used for evaluating and quantifying the value of a data before they are purchased, and 2) enthalpy-based exploration targeting based on reservoir size, temperature gradient estimates, and internal rate of return (IRR). The first approach, VOIA, aims to identify the value of a particular data when making decisions with an uncertain outcome. This approach targets the pre-drilling phase of exploration. These estimated VOIs are highly affected by the size of the project and still have a high degree of subjectivity in assignment of probabilities. The second approach, exploration targeting, is focused on decision making during the drilling phase. It starts with a basic geothermal project definition that includes target and minimum required production capacity and initial budgeting for exploration phases. Then, it uses average temperature gradient, reservoir temperature estimates, and production capacity to define targets and go/no-go limits. The decision analysis in this approach is based on achieving a minimum IRR at each phase of the project. This second approach was

  18. National symposium on commissioning and operating experiences in heavy water plants and associated chemical industries [Preprint volume

    International Nuclear Information System (INIS)

    1992-02-01

    A symposium on commissioning and operating experiences in heavy water plants and associated chemical industries (SCOPEX-92) was organised to share the experience and exchange the ideas among plant operators, designers, consultants and vendors in the areas of operation, commissioning and equipment performance. This pre-print volume has been brought out as an integrated source of information on commissioning and operation of heavy water plants. The following aspects of heavy water plants are covered: commissioning and operation, instrumentation and control, and safety and environment. (V.R.)

  19. 30 CFR 75.1913 - Starting aids.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Starting aids. 75.1913 Section 75.1913 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Diesel-Powered Equipment § 75.1913 Starting aids. (a) Volatile fuel starting aids shall be used in accordance with recommendations provided by the starting aid...

  20. Starting up the Saturne synchrotron

    International Nuclear Information System (INIS)

    Salvat, M.

    1958-02-01

    Illustrated by many drawings and graphs, this report describes and comments all operations and measurements to be performed for starting up the Saturne synchrotron until particle acceleration exclusively. The author reports the study of beam as it goes out of the Van de Graaff: experiment of position and stability of the beam axis, study of beam current and geometric characteristics (calibration of the induction probe), experiment of mass separation and proton percentage, and adjustment of regulation and Van de Graaff fall law. In a second part, he reports the optics alignment and the study of optics property (installation of the different sectors, study of inflector end voltage, and influence of inflector position in the chamber). The third part addresses the examination of phenomena associated with injection: injection method and definition of the initial instant, search for injection optimum conditions, study of particle lifetime and of phenomena on the inner probe. The fourth part proposes theoretical additional elements regarding the movement of particles at the injection in the useful area, and phenomena occurring on targets and on the inner probe

  1. Life Prediction Model for Grid-Connected Li-ion Battery Energy Storage System: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Kandler A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Saxon, Aron R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Keyser, Matthew A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Lundstrom, Blake R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Cao, Ziwei [SunPower Corporation; Roc, Albert [SunPower Corp.

    2017-08-25

    Life Prediction Model for Grid-Connected Li-ion Battery Energy Storage System: Preprint Lithium-ion (Li-ion) batteries are being deployed on the electrical grid for a variety of purposes, such as to smooth fluctuations in solar renewable power generation. The lifetime of these batteries will vary depending on their thermal environment and how they are charged and discharged. To optimal utilization of a battery over its lifetime requires characterization of its performance degradation under different storage and cycling conditions. Aging tests were conducted on commercial graphite/nickel-manganese-cobalt (NMC) Li-ion cells. A general lifetime prognostic model framework is applied to model changes in capacity and resistance as the battery degrades. Across 9 aging test conditions from 0oC to 55oC, the model predicts capacity fade with 1.4 percent RMS error and resistance growth with 15 percent RMS error. The model, recast in state variable form with 8 states representing separate fade mechanisms, is used to extrapolate lifetime for example applications of the energy storage system integrated with renewable photovoltaic (PV) power generation.

  2. Preschool Facilities - MDC_HeadStart

    Data.gov (United States)

    NSGIC Local Govt | GIS Inventory — A label (point) feature class of Head Start / Early Head Start/ Delegate Agencies/ Child Care Partnership & Family Day Care Homes Programs location in Miami-Dade...

  3. Drug Abuse Prevention Starts with Parents

    Science.gov (United States)

    ... Stages Listen Español Text Size Email Print Share Drug Abuse Prevention Starts with Parents Page Content Article Body ... for a time when drugs may be offered. Drug abuse prevention starts with parents learning how to talk ...

  4. What Happens at the Lesson Start?

    Science.gov (United States)

    Saloviita, Timo

    2016-01-01

    Transitional periods, such as lesson starts, are necessary steps from one activity to another, but they also compete with time for actual learning. The aim of the present study was to replicate a previous pilot study on lesson starts and explore possible disturbances. In total, 130 lesson starts in Finnish basic education in grades 1-9 were…

  5. Health Coordination Manual. Head Start Health Services.

    Science.gov (United States)

    Administration for Children, Youth, and Families (DHHS), Washington, DC. Head Start Bureau.

    Part 1 of this manual on coordinating health care services for Head Start children provides an overview of what Head Start health staff should do to meet the medical, mental health, nutritional, and/or dental needs of Head Start children, staff, and family members. Offering examples, lists, action steps, and charts for clarification, part 2…

  6. Teaching iSTART to Understand Spanish

    Science.gov (United States)

    Dascalu, Mihai; Jacovina, Matthew E.; Soto, Christian M.; Allen, Laura K.; Dai, Jianmin; Guerrero, Tricia A.; McNamara, Danielle S.

    2017-01-01

    iSTART is a web-based reading comprehension tutor. A recent translation of iSTART from English to Spanish has made the system available to a new audience. In this paper, we outline several challenges that arose during the development process, specifically focusing on the algorithms that drive the feedback. Several iSTART activities encourage…

  7. Start II, red ink, and Boris Yeltsin

    International Nuclear Information System (INIS)

    Arbatov, A.

    1993-01-01

    Apart from the vulnerability implied by the START II treaty, it will bear the burden of the general political opposition to the Yeltsin administration. START II will be seen as part of an overall Yeltsin-Andrei Kozyrev foreign policy that is under fire for selling out Russian national interests in Yugoslavia, the Persian Gulf, and elsewhere. This article discusses public opinion concerning START II, the cost of its implementation, and the general purpose of the treaty

  8. Starting a business through a franchise

    OpenAIRE

    Dubravka Mahaček; Maja Martinko Lihtar

    2013-01-01

    A business can be launched by establishing a new entity, purchasing an existing entity or through a franc - hise. There are certain prerequisites for starting a business, the most important ones being a quality idea and start-up capital. Potential start-up difficulties are inadequate financing, existing competition as well as the process of building your own market position. By purchasing an existing business some risks may be avoided and the opportunity for gaining profit may ...

  9. From START to NEW START. The dilemma and future of nuclear disarmament; Von START zu NEW START. Das Dilemma und die Zukunft der Nuklearen Abruestung

    Energy Technology Data Exchange (ETDEWEB)

    Plettenberg, Lars

    2012-07-01

    The report describes the existing four agreements on nuclear disarmament: START I (1991). START II (1993), SORT (2002) and NEW START (2010). The chapter on the dependence between nuclear disarmament and strategic stability covers the issues mutual assured destruction (MAD), credibility, overkill capacity; the role of nuclear weapons in the national strategies of the USA and NATO, Russia, Great Britain, France, China and the other nuclear states. Ways out of MAD include disarmament, de-alerting and mutual assured protection (MAP).

  10. Getting started with SBT for Scala

    CERN Document Server

    Saxena, Shiti

    2013-01-01

    A practical and fast-paced guide, Getting Started with SBT for Scala walks you through the setup of Scala projects in SBT with sample code for common as well as critical scenarios.Getting Started with SBT for Scala is for developers working on Scala projects who are interested in learning and utilizing Simple Build Tool to manage the build process.

  11. Families & the North Carolina Smart Start Initiative.

    Science.gov (United States)

    Lowman, Betsy; Bryant, Donna; Zolotor, Adam

    Smart Start is North Carolina's partnership between state government and local leaders, service providers, and families to better serve children under 6 years and their families. This study examined characteristics of families participating in Smart Start, their child care arrangements and family activities, and their need for and use of community…

  12. Start-up analysis for marketing strategy.

    Science.gov (United States)

    Griffith, M J; Baloff, N

    1984-01-01

    The complex start-up effect on utilization of health care services is too often overlooked or underestimated by marketing planners, leading to a range of negative consequences for both the users of services and the provider organization. Start-up analysis allows accurate estimation of these utilization effects for coordinated strategic planning among marketing finance, and operations.

  13. Head Start Impact Study. Technical Report

    Science.gov (United States)

    Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

    2010-01-01

    This Technical Report is designed to provide technical detail to support the analysis and findings presented in the "Head Start Impact Study Final Report" (U.S. Department of Health and Human Services, January 2010). Chapter 1 provides an overview of the Head Start Impact Study and its findings. Chapter 2 provides technical information on the…

  14. Start 2: Thinking one move ahead

    Energy Technology Data Exchange (ETDEWEB)

    Gaines, L.L.

    1991-11-01

    At their summit meeting in the spring of 1990, Presidents Bush and Gorbachev issued a joint statement expressing their intentions to continue the process of strategic arms control beyond the Strategic Arms Reduction Treaty (START), which was eventually signed in July 1991, toward agreement on further reductions. They set general goals for negotiation of a follow-on treaty to START, which has been called START II. President Bush`s historic speech on September 27, 1991, reinforced those goals and specified several actions the US would take. It is the purpose of this report to examine possible provisions of START II and the implications of those provisions for achievement of the goals set at the 1990 summit, for verifiability, and for US force planning. This look ahead will contribute to advance planning of appropriate negotiating positions, verification research and development (R&D), and force modernization and restructuring. This report describes the goals for a START II treaty and possible means for achieving them. It postulates one set of provisions for such a treaty, while it examines force structures for the US that could result from adoption of a treaty with these provisions. The adequacy of methods for verifying START II are examined and the implications of a START II treaty are postulated.

  15. Start 2: Thinking one move ahead

    Energy Technology Data Exchange (ETDEWEB)

    Gaines, L.L.

    1991-11-01

    At their summit meeting in the spring of 1990, Presidents Bush and Gorbachev issued a joint statement expressing their intentions to continue the process of strategic arms control beyond the Strategic Arms Reduction Treaty (START), which was eventually signed in July 1991, toward agreement on further reductions. They set general goals for negotiation of a follow-on treaty to START, which has been called START II. President Bush's historic speech on September 27, 1991, reinforced those goals and specified several actions the US would take. It is the purpose of this report to examine possible provisions of START II and the implications of those provisions for achievement of the goals set at the 1990 summit, for verifiability, and for US force planning. This look ahead will contribute to advance planning of appropriate negotiating positions, verification research and development (R D), and force modernization and restructuring. This report describes the goals for a START II treaty and possible means for achieving them. It postulates one set of provisions for such a treaty, while it examines force structures for the US that could result from adoption of a treaty with these provisions. The adequacy of methods for verifying START II are examined and the implications of a START II treaty are postulated.

  16. A Healthy Start Can Begin Now

    Science.gov (United States)

    A healthy pregnancy begins before you ever become pregnant. Give yourself the best chance for a healthy pregnancy and healthy baby before you start down the road to motherhood. If you smoke, now’s a great time to quit.

  17. The physics of tokamak start-up

    International Nuclear Information System (INIS)

    Mueller, D.

    2013-01-01

    Tokamak start-up on present-day devices usually relies on inductively induced voltage from a central solenoid. In some cases, inductive startup is assisted with auxiliary power from electron cyclotron radio frequency heating. International Thermonuclear Experimental Reactor, the National Spherical Torus Experiment Upgrade and JT60, now under construction, will make use of the understanding gained from present-day devices to ensure successful start-up. Design of a spherical tokamak (ST) with DT capability for nuclear component testing would require an alternative to a central solenoid because the small central column in an ST has insufficient space to provide shielding for the insulators in the solenoid. Alternative start-up techniques such as induction using outer poloidal field coils, electron Bernstein wave start-up, coaxial helicity injection, and point source helicity injection have been used with success, but require demonstration of scaling to higher plasma current

  18. Start small and build toward business intelligence.

    Science.gov (United States)

    Kirby, Sean; Robertson, Brian

    2009-01-01

    To use business intelligence effectively, healthcare organizations should start small, align organizationally, and leverage success. Organizations should determine which measures they need and how to present them. Organizations should reinvest savings to continually improve.

  19. Lean Start-up in Established Companies

    DEFF Research Database (Denmark)

    Goduscheit, René Chester

    2018-01-01

    Lean start-up is an emergent perspective on how entrepreneurs can bring new products and services to the market. This approach challenges the dominant role of lengthy business plans, linear product development processes, and seeking complete overview of the potential of the new products....../services before market launch. Instead it suggests that start-ups could benefit from a ‘minimum-viable product’ approach where products and services are launched when they contain critical features. The emphasis in the lean start-up approach is on business models rather than the elaborate business plan...... at the companies (strategy meetings, development workshops etc.). The aim is to shed light on the implications for companies that seek to employ lean start-up. These implications will be aimed at aspects like innovation management, organizational structure, customer relations etc....

  20. 76 FR 37174 - Capital Investment Program-New Starts and Small Starts Program Funds

    Science.gov (United States)

    2011-06-24

    ... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Capital Investment Program--New Starts... apportionment of the FY 2011 Capital Investment (New Starts and Small Starts) program funds. The funds will be... FY 2011, $1,596,800,000 was appropriated for the Capital Investments Grant Account, which includes...

  1. START: the creation of a spherical tokamak

    International Nuclear Information System (INIS)

    Sykes, Alan

    1992-01-01

    The START (Small Tight Aspect Ratio Tokamak) plasma fusion experiment is now operational at AEA Fusion's Culham Laboratory. It is the world's first experiment to explore an extreme limit of the tokamak - the Spherical Tokamak - which theoretical studies predict may have substantial advantages in the search for economic fusion power. The Head of the START project, describes the concept, some of the initial experimental results and the possibility of developing a spherical tokamak power reactor. (author)

  2. Preprints na comunicação científica da Física de Altas Energias: análise das submissões no repositório arXiv (2010-2015

    Directory of Open Access Journals (Sweden)

    Gonzalo Rubén Alvarez

    Full Text Available RESUMO A circulação de preprints na Física de Altas Energias (FAE remonta a mais de meio século, tendo como objetivos principais acelerar o processo de comunicação científica entre os pares e estimular o acesso livre à literatura especializada da área. O artigo analisa o conjunto de preprints submetidos às diferentes categorias FAE do repositório temático especializado arXiv no período 2010-2015 que foram posteriormente publicados em revistas peer review. Os indicadores bibliométricos demonstram a potencialidade dos preprints como canal precursor de difusão de resultados científicos visto que 70% das submissões foram em seguida absorvidas pelas principais revistas da FAE. Conclui que o êxito alcançado pelas iniciativas Open Access arXiv e INSPIRE-HEP favoreceu o intercâmbio de informações e conhecimentos entre os pesquisadores. O modelo proposto pela FAE pode incentivar cientistas de áreas com características similares a instalarem repositórios e bancos de dados de preprints para suas disciplinas com o intuito de fortalecer a comunicação das descobertas científicas.

  3. The impact of dry-land sprint start training on the short track speed skating start.

    Science.gov (United States)

    Haug, William B; Drinkwater, Eric J; Cicero, Nicholas J; Barthell, J Anthony; Chapman, Dale W

    2017-05-05

    This investigation sought to determine the effects of dry-land sprint start training on short track speed skating (STSS) start performance. Nine highly trained short track athletes completed a control period of normal STSS training followed by a four-week training intervention. Before and after the control and intervention periods, athletes performed three electronically timed dry-land and on-ice 14.43 m maximal sprint start efforts. The intervention consisted of two sprint sessions per week consisting of nine electronically timed 14.43 m dry-land sprint starts in addition to normal STSS training. The control period resulted in no substantial change in on-ice start performance (Mean Δ: -0.01 s, 95% Confidence Limits (CL): -0.08 to 0.05 s; Effect Size (ES): -0.05; Trivial) however, a small change was observed in dry-land start performance (Mean Δ: -0.07 s, 95% CL: -0.13 to -0.02 s; ES: -0.49). Following brief specific dry-land sprint start training a small improvement was observed in both on-ice (Mean Δ: -0.07 s, 95% CL: -0.13 to -0.01 s; ES: -0.33) and dry-land (Mean Δ: -0.04 s, 95% CL: -0.09 to 0.00 s; ES: -0.29) start performance. This investigation suggests STSS start performance can be improved through a brief dry-land sprint start training program.

  4. Guidelines for starting today's private practice

    Directory of Open Access Journals (Sweden)

    Schmitz ED

    2012-11-01

    Full Text Available No abstract available. Article truncated at 150 words. Starting a new practice may seem like a daunting task. The purpose of this article is to demystify the process of creating a new practice from the beginning. The cardinal rule is to keep costs low and not to outsource work that can easily be performed by any competent physician and staff. You do not need a manager, lawyer, business partner, coder or biller individually; you may be able to perform many of these services yourself. What you do need is a commitment to making your practice a success. Do not spend too much on your office space, furnishings or equipment. Start with the bare essentials. Immediately start applying to all insurance companies especially Medicare. Request an employer identification number. Set up a basic business banking account and submit the account number to the insurance companies you plan to work with. You can purchase an entire electronic healthcare record (EHR …

  5. Starting a business through a franchise

    Directory of Open Access Journals (Sweden)

    Dubravka Mahaček

    2013-12-01

    Full Text Available A business can be launched by establishing a new entity, purchasing an existing entity or through a franc - hise. There are certain prerequisites for starting a business, the most important ones being a quality idea and start-up capital. Potential start-up difficulties are inadequate financing, existing competition as well as the process of building your own market position. By purchasing an existing business some risks may be avoided and the opportunity for gaining profit may arise. Profitable operation is possible only if this business has up-to-date products and no outstanding liabilities. This paper discusses franchising business opportunities and the requisite investments and costs, which will bring success if they are accompanied by franchisee’s efforts. The paper aims to present the main characteristics of a franchise business, the necessary investment and the costs which arise in the process, as well as advantages, disadvantages and experiences with this kind of business

  6. Research nuclear reactor start-up simulator

    International Nuclear Information System (INIS)

    Sofo Haro, M.; Cantero, P.

    2009-01-01

    This work presents the design and FPGA implementation of a research nuclear reactor start-up simulator. Its aim is to generate a set of signals that allow replacing the neutron detector for stimulated signals, to feed the measurement electronic of the start-up channels, to check its operation, together with the start-up security logic. The simulator presented can be configured on three independent channels and adjust the shape of the output pulses. Furthermore, each channel can be configured in 'rate' mode, where you can specify the growth rate of the pulse frequency in %/s. Result and details of the implementation on FPGA of the different functional blocks are given. (author)

  7. Smart or Diverse Start-up Teams?

    DEFF Research Database (Denmark)

    Hoogendoorn, Sander; Parker, Simon C.; Van Praag, Mirjam

    2017-01-01

    This paper explores the relationship between cognitive abilities and team performance in a start-up setting. We argue that performance in this setting hinges on three tasks: opportunity recognition, problem solving, and implementation. We theorize that cognitive ability at the individual level has...... others can be assigned to tasks that impose a greater cognitive load (problem solving or opportunity recognition). We present the results of a field experiment in which 573 students in 49 teams started up and managed real companies. We ensured exogenous variation in—otherwise random—team composition...... by assigning students to teams based on their measured cognitive abilities. Each team performed a variety of tasks, often involving complex decision making. The key result of the experiment is that the performance of start-up teams first increases and then decreases with ability dispersion. Strikingly, average...

  8. Two-Man Bobsled Push Start Analysis

    Directory of Open Access Journals (Sweden)

    Lopes Alexandre Dias

    2016-04-01

    Full Text Available The importance of push start times on bobsled performance was evidenced by some studies, but at this moment there is no article to the authors’ knowledge that describes the bobsled push start. Thus, the objectives of this study were to describe the two-man bobsled push start, analyze the differences between teams, and estimate the most important variable analyzed. We hypothesized that the pilot and brakeman athletes’ movement patterns during a bobsled pushing start can be described. The images used in this study were obtained during the men’s two-man XIV World Championship of Bobsled (2004. Fifteen best teams participating in the championship were recorded, and four start runs for each team were analyzed. The videos were captured by two digital video cameras. The pilot athletes were analyzed during the moment that they touched the lateral push bar of the sled, and the brakemen were analyzed during the first take-off and first landing. The teams were pooled in three groups of five teams using the final ranking of pushing time. We concluded that there was a distinct pattern movement for pilots and brakemen. The initial position of the majority of the pilots was localized slightly behind the bar. After touching the lateral bar, the pilots remained in a semi-squat position, pushing the sled forward in a pattern of marching movement. All brakemen used the board attached to the track as a support for both feet at the start. The brakeman gave the greatest contribution to break the inertia of the sled. There was no significant difference of movement between the three groups analyzed for the pilot and the brakeman.

  9. Getting started with Microsoft Lync server 2013

    CERN Document Server

    Volpe, Fabrizio

    2013-01-01

    This book has a practical approach with a lot of step-by-step guides and explanations as to where and why we're doing the various operations.Getting Started with Microsoft Lync Server 2013 is a starting point for system administrators, IT pros, unified communication technicians, and decision makers in companies or in the consultancy business. For people who have never managed Lync (or a U.C. product), the book will guide you through the basic concepts and mistakes. If you are already managing a Lync deployment you will find important explanations and ideas put together in a single text. If you

  10. Soft start technique for diesel generator sets

    Energy Technology Data Exchange (ETDEWEB)

    Fredlund, Lars [Swedish State Power Board, Ringhals Nuclear Power Plant, S-430 22, Vaeroebacka (Sweden)

    1986-02-15

    A diesel motor in a nuclear power plant should be of a well-proven design. It is designed for long periods of trouble-free duty, but not for the frequent and rapid test starts called for by the technical specifications. In order to decrease the dynamic forces and thermal stresses, a soft-start scheme has been implemented. By limiting the fuel injection the diesel generator will reach full speed in appr. 30 seconds. The fuel limiter is a pneumatic cylinder which mechanically limits the travel of the terminal shaft of the governor. (author)

  11. Soft start technique for diesel generator sets

    International Nuclear Information System (INIS)

    Fredlund, Lars

    1986-01-01

    A diesel motor in a nuclear power plant should be of a well-proven design. It is designed for long periods of trouble-free duty, but not for the frequent and rapid test starts called for by the technical specifications. In order to decrease the dynamic forces and thermal stresses, a soft-start scheme has been implemented. By limiting the fuel injection the diesel generator will reach full speed in appr. 30 seconds. The fuel limiter is a pneumatic cylinder which mechanically limits the travel of the terminal shaft of the governor. (author)

  12. The Lean and Global Start-up

    DEFF Research Database (Denmark)

    Tanev, Stoyan; Rasmussen, Erik Stavnsager

    For several decades researchers have studied start-up companies with a focus on international markets, suppliers and networks from their inception and on companies that are establishing new, agile business models. This has resulted in two streams of research: The Born Global and International New...... Ventures research and research with a focus on the Lean Start-up company. It is our intention in this paper to give a short presentation of the two research streams and show how they can be merged into one with a focus on newly established technology oriented firms that are lean and global from...

  13. Entrepreneur How to Start an Online Business

    CERN Document Server

    Tobin, Lucy

    2012-01-01

    The secrets of the UK’s biggest online entrepreneurs revealed   Thinking of starting a business? Already have a business online and looking to take it to the next level? The wonderful world wide web has made creating a start-up that much easier. Thousands of people are out there reaping the rewards the web can bring. If you want to join them, you’ve come to the right place.  Profiling today’s foremost web entrepreneurs, Lucy Tobin - who meets successful business founders every week writing an enterprise column for The Evening Standard – takes us throug

  14. From START to NEW START. The dilemma and future of nuclear disarmament

    International Nuclear Information System (INIS)

    Plettenberg, Lars

    2012-01-01

    The report describes the existing four agreements on nuclear disarmament: START I (1991). START II (1993), SORT (2002) and NEW START (2010). The chapter on the dependence between nuclear disarmament and strategic stability covers the issues mutual assured destruction (MAD), credibility, overkill capacity; the role of nuclear weapons in the national strategies of the USA and NATO, Russia, Great Britain, France, China and the other nuclear states. Ways out of MAD include disarmament, de-alerting and mutual assured protection (MAP).

  15. Radioactive starting aids for electrodeless light sources

    International Nuclear Information System (INIS)

    Proud, J.M.; Regan, R.J.; Haugsjaa, P.O.; Baird, D.H.

    1980-01-01

    The use of radioactive sources of α particles, β particles or γ rays as aids in starting a discharge in an electrodeless light source is discussed. The advantages of siting the sources at various positions in the device are discussed. Preferred materials are 85 Kr and 241 Am. (U.K.)

  16. The Start of a Tech Revolution

    Science.gov (United States)

    Dyrli, Kurt O.

    2009-01-01

    We are at the start of a revolution in the use of computers, one that analysts predict will rival the development of the PC in its significance. Companies such as Google, HP, Amazon, Sun Microsystems, Sony, IBM, and Apple are orienting their entire business models toward this change, and software maker SAS has announced plans for a $70 million…

  17. START to Get Ready for Breastfeeding

    Science.gov (United States)

    Breastfeeding is a great way to give your baby the nutrients he or she needs to grow and develop. Breastfeeding also can help you and your baby form a special bond. Breastfeeding can be good for both of you if you know where to S-T-A-R-T.

  18. Automobile Starting and Lighting System Maintenance Training ...

    African Journals Online (AJOL)

    The purpose of this study is to develop automobile starting and lighting system maintenance training manual for technical college students. Research and Development (R and D) design was adopted for the study. The population of the study is 348, comprising of 76 auto-mechanics teachers, 36 automobile supervisors and ...

  19. Addressing Tooth Decay in Head Start Children

    Science.gov (United States)

    Knowlden, Adam P.; Hill, Lawrence F.; Alles-White, Monica L.; Cottrell, Randall R.

    2012-01-01

    Tooth decay is the most prevalent chronic disease of childhood. Oral health education and dental services are crucial to reducing the number of children afflicted with dental cavities. Due to limited access to preventative care, Head Start children are particularly vulnerable to tooth decay. This article outlines practical implications of a…

  20. Single phase induction motor with starting performance

    Energy Technology Data Exchange (ETDEWEB)

    Popescu, M.; Demeter, E. [Research Institute for Electrical Machines, ICPE-ME, Bucharest (Romania); Navrapescu, V. [University `Politehnica` Bucharest, Electrical Engineering Faculty Splaiul Independentei, Bucharest (Romania)

    1997-12-31

    The paper presents problems related to a special type of single phase induction motor. The main novelty consists in the use of a conducting (aluminium casted) shell distributed on the periferic region of the rotor. As a result the starting performance, as well as the rated ones, is much improved in comparison with the conventional construction. (orig.) 4 refs.

  1. From Jam to Start-up

    DEFF Research Database (Denmark)

    Bering Kjæhr, Emil; Lyngbye Hvid Jensen, Jane; Schoenau-Fog, Henrik

    2015-01-01

    the foundation for new start-up companies. There are, however, an even larger group of very creative and innovative games and artifacts with great potential that go unpublished. This potentially leads to a loss of entrepreneurial opportunities and ultimately the jobs and careers such games could have fostered...

  2. An Overview of Head Start Program Studies

    Science.gov (United States)

    Hines, Jeanne Morris

    2017-01-01

    Johnson's "War on Poverty" administrative team campaigned for committee members to join the War on Poverty efforts to create and develop programs for children born into poverty (Zigler, 2003). Poverty based programs, such as the Head Start program, continue to put into place proactive measures to increase preschooler's cognitive…

  3. School Start Time and Teen Sleep.

    Science.gov (United States)

    Wahlstrom, Kyla L.

    2000-01-01

    Sleep studies have shown that teenagers' internal clocks are incompatible with most high schools' early hours. Research in two Minnesota districts indicates that later school starting times can benefit teens and everyone dealing with them. Student participation in sports and other afterschool activities remained high. (MLH)

  4. Getting started with Magento module development

    CERN Document Server

    Ajzele, Branko

    2013-01-01

    This project-based tutorial gives you a strong foundation and guides you through practical, real-world examples.This book contains valuable insights for both newbies and already established Magento developers. This book is targeted at new and intermediate PHP developers starting afresh with Magento module development.

  5. Getting started with OrientDB

    CERN Document Server

    Tesoriero, Claudio

    2013-01-01

    A standard tutorial aimed at making you an OrientDB expert, through the use of practical examples, explained in a step-by-step format.Getting Started with OrientDB 1.3.0 is great for database designers, developers, and systems engineers. It is assumed that you are familiar with NoSQL concepts, Java, and networking principles.

  6. An Alternative Starting Point for Fraction Instruction

    Science.gov (United States)

    Cortina, José Luis; Višnovská, Jana; Zúñiga, Claudia

    2015-01-01

    We analyze the results of a study conducted for the purpose of assessing the viability of an alternative starting point for teaching fractions. The alternative is based on Freudenthal's insights about fraction as comparison. It involves portraying the entities that unit fractions quantify as always being apart from the reference unit, instead of…

  7. Evaluation of Hawaii's Healthy Start Program.

    Science.gov (United States)

    Duggan, Anne K.; McFarlane, Elizabeth C.; Windham, Amy M.; Rohde, Charles A.; Salkever, David S.; Fuddy, Loretta; Rosenberg, Leon A.; Buchbinder, Sharon B.; Sia, Calvin C. J.

    1999-01-01

    Describes Hawaii's Healthy Start Program (HST), its ongoing evaluation study, and evaluation findings at the end of two of a planned three years of family-program participation and follow-up. HST uses home visitors to help prevent abusive and neglectful parenting. Found significant differences in program implementation among the three…

  8. Starting Up after 50. CELCEE Digest.

    Science.gov (United States)

    Seymour, Nicole

    Researchers are finding that older entrepreneurs are an increasing population in many Western countries. It is important to distinguish between entrepreneurs who have simply reached the age of 50 versus those who start up businesses after this age. The latter group is of particular interest because these people have presumably never faced the…

  9. Starting Small, Thinking Big - Continuum Magazine | NREL

    Science.gov (United States)

    , Thinking Big Stories NREL Helps Agencies Target New Federal Sustainability Goals Student Engagements Help solar power in the territory. Photo by Don Buchanan, VIEO Starting Small, Thinking Big NREL helps have used these actions to optimize that energy use.'" NREL's cross-organizational work supports

  10. 76 FR 70009 - Head Start Program

    Science.gov (United States)

    2011-11-09

    ... importance of the early years of a child's growth and development. On December 12, 2007, the Improving Head... education, serving nearly one million of our nation's most vulnerable young children and their families. It... Administration for Children and Families 45 CFR Part 1307 Head Start Program; Final Rule #0;#0;Federal Register...

  11. Early Start DENVER Model: A Meta - analysis

    Directory of Open Access Journals (Sweden)

    Jane P. Canoy

    2015-11-01

    Full Text Available Each child with Autism Spectrum Disorder has different symptoms, skills and types of impairment or disorder with other children. This is why the word “spectrum” is included in this disorder. Eapen, Crncec, and Walter, 2013 claimed that there was an emerging evidence that early interventions gives the greatest capacity of child’s development during their first years of life as “brain plasticity” are high during this period. With this, the only intervention program model for children as young as 18 months that has been validated in a randomized clinical trial is “Early Start Denver Model” (ESDM. This study aimed to determine the effectiveness of the outcome of “Early Start Denver Model” (ESDM towards young children with Autism Spectrum Disorders. This study made use of meta-analysis method. In this study, the researcher utilized studies related to “Early Start Denver Model (ESDM” which is published in a refereed journal which are all available online. There were five studies included which totals 149 children exposed to ESDM. To examine the “pooled effects” of ESDM in a variety of outcomes, a meta-analytic procedure was performed after the extraction of data of the concrete outcomes. Comprehensive Meta Analysis Version 3.3.070 was used to analyze the data.  The effectiveness of the outcome of “Early Start Denver Model” towards young children with Autism Spectrum Disorders (ASD highly depends on the intensity of intervention and the younger child age. This study would provide the basis in effectively implementing an early intervention to children with autism such as the “Early Start Denver Model” (ESDM that would show great outcome effects to those children that has “Autism Spectrum Disorder”.

  12. 45 CFR 1308.21 - Parent participation and transition of children into Head Start and from Head Start to public...

    Science.gov (United States)

    2010-10-01

    ... into Head Start and from Head Start to public school. 1308.21 Section 1308.21 Public Welfare... AND HUMAN SERVICES THE ADMINISTRATION FOR CHILDREN, YOUTH AND FAMILIES, HEAD START PROGRAM HEAD START... Standards § 1308.21 Parent participation and transition of children into Head Start and from Head Start to...

  13. Software for physical start-up console

    International Nuclear Information System (INIS)

    Arbet, L.; Suchy, R.

    1991-01-01

    The physical start-up console comprises an PC AT-based control unit equipped with an 80386 processor, and information input/output units. The basic functions to be fulfilled by the control unit software include data acquisition related to the following parameters: neutron physics properties of the reactor core (neutron fluxes recorded by ionization chambers and reactivity recorded by a digital reactimeter), positions of the reactor core control elements (by the digital position meter) and reactor core control measurements, and technological quantities requisite for evaluating physical start-up tests. The measured and calculated data are shown on the control unit display. The setup of the data acquisition system and of user programs is dealt with, and characteristics of the user processes are briefly described. (Z.S.)

  14. Secondary Circuit Start Up Chemistry Optimisation

    International Nuclear Information System (INIS)

    Fontan, Guillaume; Morel, Pascal

    2012-09-01

    In a context of investment and renewal of equipment, Electricite De France (EDF) put enhanced efforts on operating practices during start-up of the secondary circuit, in order to improve operational performance and materials lifetime. This article focuses on the objective of optimizing the filling, the chemical conditioning and the thermal conditioning of the secondary fluid, while taking into account the following issues: - Limiting the time required to obtain a proper chemistry, - Limiting the amount of water and steam used, - Limiting the amount of effluent generated. The scope is all start-up conditions of secondary circuit, both after refuelling outage or fortuitous shutdowns of the plant. The recommendations produced are based on existing local procedures and good practices, which were collected and developed in order to propose a generic methodology understandable and useful both for operators, chemists and managers. (authors)

  15. Single start multiple stop time digitizer

    International Nuclear Information System (INIS)

    Deshpande, P.A.; Mukhopadhyay, P.K.; Gopalakrishnan, K.R.

    1997-01-01

    A single start multiple stop time digitizer has been developed which can digitize the time between a start pulse and multiple stop pulses. The system has been designed as a PC add on card. The resolution of the instrument is 10 nSecs and the maximum length of time that it can measure is 1.28 milliseconds. Apart from time digitization, it can also resolve the height of the incoming pulses into 64 levels. After each input pulse the system dead time is less than 300 nSecs. The driver software for this card has been developed on DOS platform. It uses graphical user interface to provide a user friendly environment. The system is intended to be used in time of flight mass spectroscopy experiments. It can also be used for time of flight experiments in nuclear physics. (author). 2 figs

  16. Lean and global technology start-ups

    DEFF Research Database (Denmark)

    Tanev, Stoyan; Rasmussen, Erik Stavnsager; Zijdemans, Erik

    2015-01-01

    In this paper the authors introduce the concept of Lean Global Start-up (LGS) as a way of emphasizing the impossibility for new technology start-ups to deal separately with business development, innovation and early internationalization. For a newly established technology firm the task of being...... global and innovative at the same time should be seen as one process. The paper has two components – an introductory conceptual part and an empirical part that should be considered as basis for the preliminary validation of the conceptual insights. The research sample includes six firms – three from...... Canada and three from Denmark. The firms have had significant problems with the complexity, uncertainties and risks of being innovative on a global scale. They have however found ways of addressing these problems by a disciplined knowledge sharing and IP protection strategy and the efficient use...

  17. Starting apparatus for internal combustion engines

    Science.gov (United States)

    Dyches, Gregory M.; Dudar, Aed M.

    1997-01-01

    An internal combustion engine starting apparatus uses a signal from a curt sensor to determine when the engine is energized and the starter motor should be de-energized. One embodiment comprises a transmitter, receiver, computer processing unit, current sensor and relays to energize a starter motor and subsequently de-energize the same when the engine is running. Another embodiment comprises a switch, current transducer, low-pass filter, gain/comparator, relay and a plurality of switches to energize and de-energize a starter motor. Both embodiments contain an indicator lamp or speaker which alerts an operator as to whether a successful engine start has been achieved. Both embodiments also contain circuitry to protect the starter and to de-energize the engine.

  18. Getting started with MariaDB

    CERN Document Server

    Bartholomew, Daniel

    2013-01-01

    A practical, hands-on, beginner-friendly guide to installing and using MariaDB.Getting Started with MariaDB is for anyone who wants to learn more about databases in general or MariaDB in particular. No prior database experience is required. It is assumed that you have basic knowledge of software installation, editing files with a text editor, and using the command line and terminal.

  19. The 2002 Starting Artificial Intelligence Researchers Symposium

    OpenAIRE

    Vidal, Thierry

    2003-01-01

    During the 2002 European Conference on Artificial Intelligence (ECAI-02) was introduced the Starting Artificial Intelligence Researchers Symposium STAIRS), the first-ever international symposium specifically aimed at Ph.D. students in AI. The outcome was a thorough, high-quality, and successful event, with all the features one usually finds in the best international conferences: large international committees, comprehensive coverage, published proceedings, renowned speakers and panelists, sub...

  20. The rotating converter GKN II starts operation

    International Nuclear Information System (INIS)

    Jergas, E.

    1989-01-01

    At the beginning of 1989 the energy supply and consumption of the 110-kV-railway mains has changed considerably with starting the rotating converter of the German Federal Railways (DB) in the joint nuclear power station Neckar GmbH (GKN) block II. A description is given of the planned utilization of the rotating converters at baseload operation and possibilities for optimal energy use are shown. (orig.) [de

  1. Business Models for Start up Business

    OpenAIRE

    Boban, Nitin

    2010-01-01

    Gamingdom is a new start up venture that provides online gaming service utilising the latest cloud computing technology. The high demand, popularity and exponential growth in the number of gaming enthusiasts and the market have brought about this innovative idea. This new venture aims to provide an easy method of gaming through the internet without heavy expenses on hardware and software and also minimising the existing high rate of piracy. A business model is an essential tool for buildin...

  2. New Start of “Psychological Thought”

    Directory of Open Access Journals (Sweden)

    Stanislava Stoyanova

    2012-05-01

    Full Text Available The history and the mission of Psychological Thought are presented. The scientific journal “Psychological Thought” started its existence as an idea of the colleagues at the Department of Psychology at South-West University “Neofit Rilski” in 2006. Seven print issues were published from 2006 to 2009 (2 issues per year. Each issue included average ten articles published in Bulgarian or in English.

  3. Getting started with nopCommerce

    CERN Document Server

    Atkinson, Brandon

    2013-01-01

    A friendly, tutorial style book, which will help you learn your way through creating a live storefront with nopCommerce in a step-by-step manner.Getting Started with nopCommerce is for anyone who wants to sell products online using nopCommerce. If you are a non-technical person and are discouraged by the complexity of this powerful e-commerce application, then this book is for you.

  4. Starting and developing a surveying business

    CERN Document Server

    Imber, Austen

    2013-01-01

    Starting and Developing a Surveying Business shows how surveyors can develop their own successful small business. For surveyors thinking of taking this step, guidance is provided on the pros and cons which will help the right decision to be made, and the key factors which help see the business through its early stages. For surveyors already running their own small business, consideration is given to factors which will help profitability and growth potential.

  5. A Fast-Starting Robotic Fish

    Science.gov (United States)

    Modarres-Sadeghi, Yahya; Watts, Matthew; Conte, Joe; Hover, Franz; Triantafyllou, Michael

    2009-11-01

    We have built a simple mechanical system to emulate the fast-start performance of fish. The system consisted of a thin metal beam covered by a urethane rubber fish body. The body form of the mechanical fish in this work was modeled from a pike species, which is the most successfully studied fast-start specialist species. The mechanical fish was held in curvature and hung in water by two restraining lines, which were simultaneously released by pneumatic cutting mechanisms. The potential energy in the beam was transferred into the fluid, thereby accelerating the fish, similar to a pike. We measured the resulting velocity and acceleration, as well as the efficiency of propulsion for the mechanical fish model and also ran a series of flow visualization tests to observe the resulting flow pattern. We also studied the influence of stiffness and geometry of the tail on the efficiency of propulsion and flow pattern. The hydrodynamic efficiency of the fish, calculated by the transfer of energy, was around 10%. Flow visualization of the mechanical fast-start wake was also analyzed, showing that the acceleration is associated with the fast movement of an intense vortex in a near-lateral direction.

  6. Method of starting up PWR type reactor

    International Nuclear Information System (INIS)

    Kadokami, Akira; Ueno, Ryuji; Tsuge, Ayao; Onimura, Kichiro; Ochi, Tatsuya.

    1988-01-01

    Purpose: To start-up a PWR type reactor so as to effectively impregnate and concentrate corrosion inhibitors in intergranular corrosive faces. Method: Upon reactor start-up, after transferring from the warm zero output state to thermal power loaded state and injecting corrosion inhibitors, thermal power is returned to zero and, subsequently, increased up to a rated power. By selecting the thermal power upon injecting the corrosion inhibitors to a steam generator body, that is, by selecting a thermal power load that starts to boil in heat conduction tubes, feedwater in the clavis portion can be formed into an appropriate boiling convection and, accordingly, the corrosion inhibitors can be penetrated to the clevis portion at a higher rate and in a greater amount as compared with those under zero power condition. Subsequently, when the thermal power is reduced, a sub-cooled state is attained in the clevis portion, in which steams present in the intergranular corrosion faces in the heat conduction tubes are condensated. As a result, the corrosion inhibitors at high concentration are impregnated into the intergranular corrosive faces to provide excellent effects. (Kamimura, M.)

  7. Exercise starts and ends in the brain.

    Science.gov (United States)

    Kayser, Bengt

    2003-10-01

    Classically the limit to endurance of exercise is explained in terms of metabolic capacity. Cardio-respiratory capacity and muscle fatigue are thought to set the limit and the majority of studies on factors limiting endurance exercise discuss issues such as maximal oxygen uptake (VO2max), aerobic enzyme capacity, cardiac output, glycogen stores, etc. However, this paradigm does not explain the limitation to endurance exercise with large muscle groups at altitude, when at exhaustion exercise is ended without limb locomotor muscle fatigue and with sub-maximal cardiac output. A simple fact provides a basis for an explanation. Voluntary exercise starts and ends in the brain. It starts with spatial and temporal recruitment of motor units and ends with their de-recruitment. A conscious decision precedes a voluntary effort. The end of effort is again volitional and a forced conscious decision to stop precedes it, but it is unknown what forces the off-switch of recruitment at exhaustion although sensation of exertion certainly plays a role. An alternative model explaining the limitation of exercise endurance thus proposes that the central nervous system integrates input from various sources all related to the exercise and limits the intensity and duration of recruitment of limb skeletal muscle to prevent jeopardizing the integrity of the organism. This model acknowledges the cardio-respiratory and muscle metabolic capacities as prime actors on the performance scene, while crediting the central nervous system for its pivotal role as the ultimate site where exercise starts and ends.

  8. Key parameters of the swimming start and their relationship to start performance.

    Science.gov (United States)

    Tor, Elaine; Pease, David L; Ball, Kevin A

    2015-01-01

    The swimming start is typically broken into three sub-phases; on-block, flight, and underwater phases. While overall start performance is highly important to elite swimming, the contribution of each phase and important technical components within each phase, particularly with the new kick-start technique, has not been established. The aim of this study was to identify technical factors associated with overall start performance, with a particular focus on the underwater phase. A number of parameters were calculated from 52 starts performed by elite freestyle and butterfly swimmers. These parameters were split into above-water and underwater groupings, before factor analysis was used to reduce parameter numbers for multiple regression. For the above-water phases, 81% of variance in start performance was accounted for by take-off horizontal velocity. For the underwater water phase, 96% of variance was accounted for with time underwater in descent, time underwater in ascent and time to 10 m. Therefore, developing greater take-off horizontal velocity and focussing on the underwater phase by finding the ideal trajectory will lead to improved start performance.

  9. 46 CFR 112.50-7 - Compressed air starting.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Compressed air starting. 112.50-7 Section 112.50-7... air starting. A compressed air starting system must meet the following: (a) The starting, charging... air compressors addressed in paragraph (c)(3)(i) of this section. (b) The compressed air starting...

  10. START: an advanced radiation therapy information system.

    Science.gov (United States)

    Cocco, A; Valentini, V; Balducci, M; Mantello, G

    1996-01-01

    START is an advanced radiation therapy information system (RTIS) which connects direct information technology present in the devices with indirect information technology for clinical, administrative, information management integrated with the hospital information system (HIS). The following objectives are pursued: to support decision making in treatment planning and functional and information integration with the rest of the hospital; to enhance organizational efficiency of a Radiation Therapy Department; to facilitate the statistical evaluation of clinical data and managerial performance assessment; to ensure the safety and confidentiality of used data. For its development a working method based on the involvement of all operators of the Radiation Therapy Department, was applied. Its introduction in the work activity was gradual, trying to reuse and integrate the existing information applications. The START information flow identifies four major phases: admission, visit of admission, planning, therapy. The system main functionalities available to the radiotherapist are: clinical history/medical report linking function; folder function; planning function; tracking function; electronic mail and banner function; statistical function; management function. Functions available to the radiotherapy technician are: the room daily list function; management function: to the nurse the following functions are available: patient directing function; management function. START is a departmental client (pc-windows)-server (unix) developed on an integrated database of all information of interest (clinical, organizational and administrative) coherent with the standard and with a modular architecture which can evolve with additional functionalities in subsequent times. For a more thorough evaluation of its impact on the daily activity of a radiation therapy facility, a prolonged clinical validation is in progress.

  11. Getting started with Zurb Foundation 4

    CERN Document Server

    Patterson, Andrew D

    2013-01-01

    The book starts with the basics of Foundation and helps you build your skills as you advance from installation to design, configuration, and customization with examples at every step.This book will be of great benefit to web architects, designers, and builders. While it helps to be a programmer, it isn't necessary for this book. You should be familiar with the basic principles of responsive web design and have a desire to create a professional website that looks great on both mobile devices and regular displays.

  12. Getting started in 3D with Maya

    CERN Document Server

    Watkins, Adam

    2012-01-01

    Deliver professional-level 3D content in no time with this comprehensive guide to 3D animation with Maya. With over 12 years of training experience, plus several award winning students under his belt, author Adam Watkins is the ideal mentor to get you up to speed with 3D in Maya. Using a structured and pragmatic approach Getting Started in 3D with Maya begins with basic theory of fundamental techniques, then builds on this knowledge using practical examples and projects to put your new skills to the test. Prepared so that you can learn in an organic fashion, each chapter builds on the know

  13. Getting started with FortiGate

    CERN Document Server

    Fabbri, Rosato

    2013-01-01

    This book is a step-by-step tutorial that will teach you everything you need to know about the deployment and management of FortiGate, including high availability, complex routing, various kinds of VPN working, user authentication, security rules and controls on applications, and mail and Internet access.This book is intended for network administrators, security managers, and IT pros. It is a great starting point if you have to administer or configure a FortiGate unit, especially if you have no previous experience. For people that have never managed a FortiGate unit, the book helpfully walks t

  14. Getting started with the Lazarus IDE

    CERN Document Server

    Person, Roderick

    2013-01-01

    This book is written in a simple, easy-to-understand format with lots of screenshots and step-by-step explanations.This book is geared toward developers that have a familiarity with Delphi or Free Pascal and would like to start using the open source Lazarus Integrated Development Environment. You should have knowledge of creating a console and GUI applications as well as creating basic components. Example source code and projects are provided to help learn the differences between Delphi and Lazarus projects.

  15. Participation in testing and start up operations

    International Nuclear Information System (INIS)

    Prasad, Y.S.R.

    1977-01-01

    Testing and start up operations of a nuclear power plant require careful planning. A detailed program of tests and the responsibility of implementing them is discussed. Requirement of documentation covering the tests and operating procedures is explained. The performance of the system during normal and abnomal operating conditions is analysed and required are modifications carried out. Various phases of commissioning and their significance are explained. Preparation of maintenance documentation and training of operating and maintenance staff during this period are discussed. Necessity of close liaison between the regulatory body and the operating organization is explained. (orig.) [de

  16. EU Emission Trading: Starting with Carbon Dioxide

    DEFF Research Database (Denmark)

    Vesterdal, Morten; Svendsen, Gert Tinggaard

    2003-01-01

    The Commission of the European Union wants to start a limited emission trading scheme by 2005 within the Community to enable "learning-by-doing" prior to the Kyoto Protocol. This to accomplish the desired 8% target level for six different greenhouse gases. However, in the EU it is not clear whether...... all the six relevant greenhouse gases or only CO2 should be traded. What is the simplest and most practicable solution? We argue in favour of the latter option for three main reasons: the possible dominating global warming potential of CO2, expected future developments in CO2 emissions and the fact...

  17. Start-up tests of NSRR

    International Nuclear Information System (INIS)

    1976-12-01

    Start up tests of the Nuclear Safety Research Reactor (NSRR) were carried out from June 25 to August 15, 1975. The course of tests is in three stage, i.e. critical approach and zero power, power-up and pulse operation. Performance of the reactor was shown to be in good agreement with the design specifications in both steady-state and pulse operations. Test procedures and the results are presented in four parts: (I) general, (II) zero-power tests, (III) power-up tests, and (IV) pulse operation tests. (auth.)

  18. Particle Physics at the LHC Start

    CERN Document Server

    Altarelli, Guido

    2011-01-01

    I present a concise review of the major issues and challenges in particle physics at the start of the LHC era. After a brief overview of the Standard Model and of QCD, I will focus on the electroweak symmetry breaking problem which plays a central role in particle physics today. The Higgs sector of the minimal Standard Model is so far just a mere conjecture that needs to be verified or discarded by the LHC. Probably the reality is more complicated. I will summarize the motivation for new physics that should accompany or even replace the Higgs discovery and a number of its possible forms that could be revealed by the LHC.

  19. Getting started with ownCloud

    CERN Document Server

    Patawari, Aditya

    2013-01-01

    This is a standard, precise, and short tutorial for setting up ownCloud and includes advanced topics like encryption, user management, and server security. This ownCloud book would be an ideal starting point for anyone who wants to store their data and also share it.This book is for first time users as well as administrators who are interested or responsible for managing an ownCloud instance. You do not need any prior experience with any of the technology, including Linux/Windows, Apache/IIS, SQLite/MySQL, or even PHP. It is a beginner-friendly book, written with a first time user in mind.

  20. Starting a Chinese Sauce Company in Helsinki

    OpenAIRE

    Shu, Bing; Shi, Jianan

    2017-01-01

    The thesis is about starting-up a Chinese sauce company in Helsinki. The introduction is about the history of Laoganma company and the missions of a branch company in Helsinki, as well as the aims of the project. The part about market research includes the current situation of Finnish sauce market and a SWOT analysis for a Finnish market entrance. Also, a successful case reflects the developed way for the company. Then, the price and location are defined in the thesis. Sales strategi...

  1. Take Control of Getting Started with Dreamweaver

    CERN Document Server

    Keller, Arnie

    2009-01-01

    Learn fundamental Web design principles and become comfortable working in Dreamweaver's complex interface! Dreamweaver 8 is a great Web design tool for pros, but newcomers may be overwhelmed by its interface or want to know more about how to work creatively and intelligently in the program. Help is at hand in Take Control of Getting Started with Dreamweaver, which offers a detailed tutorial for making your first site in Dreamweaver. Author Arnie Keller, who teaches Web design at the University of Victoria, shows you how to style type the smart way with CSS, create a sophisticated page layout

  2. ORGANIZING THE MUSIC CLASSES IN STARTING SCHOOLS

    Directory of Open Access Journals (Sweden)

    N. G. Tagiltseva

    2013-01-01

    Full Text Available The paper considers the issue of children preparation for school in so called starting schools. In author’s opinion, the arts disciplines such as music, drawing and choreography can develop the aesthetic sense, moral qualities, more optimistic world outlook and respectful  attitude; the child develops creative skills and beauty perception both in fine arts and wild life.The author looks at the problems of planning and organizing the music training of preschool children, the different requirements for and concepts of the preschool and primary school normative documents being analyzed. The paper substantiates the effectiveness of poly-artistic and activity approaches to the split-level teaching, in particular – the method of projecting the familiar actions onto some sort of artistic activities. Based on the succession of preschool and primary school training, the author specifies the goals of music classes in starting schools, and outlines the most relevant game activities of role plays, didactic plays and contests.The paper is addressed to preschool and primary school teachers, music teachers, as well as methodologists and researchers dealing with preschool teaching. 

  3. LHC Report: Rocky re-start

    CERN Multimedia

    Barbara Holzer for the LHC Team

    2012-01-01

    A rocky re-start with beam followed a successful machine development period and the first technical stop of 2012. Today, Friday 11 May, the machine began running again with 1380 bunches.   A short, two-day machine development period was successfully completed on 21-22 April. It focused on topics relevant for the 2012 physics beam operation. This was then followed by a five-day technical stop, the first of the year. The technical stop finished on time on Friday 26 April. The re-start with beam was somewhat tortuous and hampered by an unlucky succession of technical faults leading to extended periods of downtime. The planned intensity increase was put on hold for three days with the machine operating with 1092 bunches and a moderate bunch intensity of 1.3x1011 protons. This delivered a reasonable peak luminosity of 3.6x1033 cm-2s-1 to ATLAS and CMS. Higher than usual beam losses were observed in the ramp and squeeze, and time was required to investigate the causes and to implement mitigati...

  4. Danish Ophthalmology - from start to 1865.

    Science.gov (United States)

    Norn, Mogens

    2016-03-01

    This short paper mentioned the medical treatment using the 'holy' springs, the first 'eye doctor' in Denmark, the first picture of spectacles which was found in Viborg Cathedral of the high priest before he performs circumcisio praeputii on Jesus Christ, further cataract reclination in Denmark from around year zero and cataract extraction in 1667 in Denmark on a goose by Francisco Borri and on humans by the Danish Georg Heuermann in 1755. Epidemic military eye diseases in 1807, 1856 and 1865 are also described in this study. From 1856, a new ophthalmological period started in Denmark with the first eye hospital (lazaret only for eye diseases), and in 1864, patients with eye diseases were transported from the few beds in the surgical departments in the municipal hospital to the first civil eye department in Denmark, the eye hospital Sct. Annae in Copenhagen. The new scientific period started with Jacob Christian Bentz (ophthalmia granulosa, joint editor of the Danish Medical Journal) and Heinrich Lehmann. © 2016 Acta Ophthalmologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

  5. Inadvertent pump start with gas expansion modules

    International Nuclear Information System (INIS)

    Campbell, L.R.; Harris, R.A.; Heard, F.J.; Dautel, W.A.

    1992-01-01

    Previous testing demonstrated the effectiveness of gas expansion modules (GEMs) in mitigating the consequences of a loss-of-flow-without-scram transient in Fast Flux Test Facility (FFTF)-sized sodium cooled cores. As a result, GEMs have been included in the advance liquid-metal reactor (PRISM) design project sponsored by the US Department of Energy. The PRISM design is under review at the US Nuclear Regulatory Commission for licensability. In the unlikely event that the reactor does not scram during a loss of low, the GEMs quickly insert sufficient negative reactivity to limit fuel and cladding temperatures to acceptable values. This is the positive benefit of the GEMs; however, the reverse situation must be considered. A primary pump could be inadvertently started from near-critical conditions resulting in a positive reactivity insertion and a power transient. One mitigating aspect of this event is that as the reactivity associated with the GEMs is inserted, the increasing flow increases core cooling. A test was conducted in the FFTF to demonstrate that the GEM and feedback reactivity are well predicted following pump start, and the reactivity transient is benign

  6. Bauxite slurry pipeline: start up operation

    Energy Technology Data Exchange (ETDEWEB)

    Othon, Otilio; Babosa, Eder; Edvan, Francisco; Brittes, Geraldo; Melo, Gerson; Janir, Joao; Favacho, Orlando; Leao, Marcos; Farias, Obadias [Vale, Rio de Janeiro, RJ (Brazil); Goncalves, Nilton [Anglo Ferrous Brazil S.A., Rio de Janeiro, RJ (Brazil)

    2009-07-01

    The mine of Miltonia is located in Paragominas-PA, in the north of Brazil. Bauxite slurry pipeline starts at the Mine of Miltonia and finishes in the draining installation of Alunorte refinery at the port of Barcarena-PA, located approximately 244km away from the mine. The pipeline runs over seven cities and passes below four great rivers stream beds. The system was designed for an underground 24 inches OD steel pipe to carry 9.9 million dry metric tonnes per annum (dMTAs) of 50.5% solid concentration bauxite slurry, using only one pumping station. The system is composed by four storage tanks and six piston diaphragm pumps, supplying a flow of 1680 m3/h. There is a cathodic protection system along the pipeline extension to prevent external corrosion and five pressure monitoring stations to control hydraulic conditions, there is also a fiber optic cable interconnection between pump station and terminal station. Pipeline Systems Incorporated (PSI) was the designer and followed the commissioning program of the start up operations. This paper will describe the beginning of the pipeline operations, technical aspects of the project, the operational experiences acquired in these two years, the faced problems and also the future planning. (author)

  7. Giving start-ups a helping hand

    CERN Multimedia

    2008-01-01

    The French-Swiss foundation for research and technology (FFSRT) joined forces with CERN to organise an information day on setting up new businesses, at the Globe of Science and Innovation. The participants heard talks by entrepreneurs who started out at CERN, sharing their experiences and difficulties.CERN is a hot-bed of high-tech skills and know-how, and the Organization works actively to transfer this expertise to society. Some such innovations can lead to new business start-ups, but it can be extremely difficult to obtain the information and support you need to find your way through the inevitable administrative labyrinth. By opening its doors to the Fondation franco-suisse pour la recherche et la technologie (FFSRT) and hosting this "Entrepreneurial Day" on 7 March, CERN has clearly flagged its desire to assist budding entrepreneurs. The day was jointly kicked off by Olga Hooft, General Manager of the FFSRT, and Maximilian Metzger, CERN’s Se...

  8. High Time Resolution Measurements of VOCs from Vehicle Cold Starts: The Air Toxic Cold Start Pulse

    Science.gov (United States)

    Jobson, B. T.; Huangfu, Y.; Vanderschelden, G. S.

    2017-12-01

    Pollutants emitted during motor vehicle cold starts, especially in winter in some climates, is a significant source of winter time air pollution. While data exist for CO, NO, and total hydrocarbon emissions from federal testing procedures for vehicle emission certification, little is known about the emission rates of individual volatile organic compounds, in particular the air toxics benzene, formaldehyde, and acetaldehyde. Little is known about the VOC speciation and temperature dependence for cold starts. The US EPA vehicle emission model MOVES assumes that cold start emissions have the same speciation profile as running emissions. We examined this assumption by measuring cold start exhaust composition for 4 vehicles fueled with E10 gasoline over a temperature range of -4°C to 10°C in winter of 2015. The extra cold start emissions were determined by comparison with emissions during engine idling. In addition to CO and NOx measurements a proton transfer reaction mass spectrometer was used to measure formaldehyde, acetaldehyde, benzene, toluene, and C2-alkylbenzenes at high time resolution to compare with the cold start emission speciation profiles used in the EPA MOVES2014 model. The results show that after the vehicle was started, CO mixing ratios can reach a few percent of the exhaust and then drop to several ppmv within 2 minutes of idling, while NOx showed different temporal behaviors among the four vehicles. VOCs displayed elevated levels during cold start and the peak mixing ratios can be two orders higher than idling phase levels. Molar emission ratios relative to toluene were used to compare with the emission ratio used in MOVES2014 and we found the formaldehyde-to-toluene emission ratio was about 0.19, which is 5 times higher than the emission ratio used in MOVES2014 and the acetaldehyde-to-toluene emission ratios were 0.86-0.89, which is 8 times higher than the ones in MOVES2014. The C2-alkylbenzene-to-toluene ratio agreed well with moves. Our results

  9. The UK sugar tax - a healthy start?

    Science.gov (United States)

    Jones, C M

    2016-07-22

    The unexpected announcement by the UK Chancellor of the Exchequer of a levy on sugar sweetened beverages (SSBs) on the 16 March 2016, should be welcomed by all health professionals. This population based, structural intervention sends a strong message that there is no place for carbonated drinks, neither sugared nor sugar-free, in a healthy diet and the proposed levy has the potential to contribute to both general and dental health. The sugar content of drinks exempt from the proposed sugar levy will still cause tooth decay. Improving the proposed tax could involve a change to a scaled volumetric tax of added sugar with a lower exemption threshold. External influences such as the Common Agricultural Policy and the Transatlantic Trade and Investment Partnership may negate the benefits of the sugar levy unless it is improved. However, the proposed UK sugar tax should be considered as a start in improving the nation's diet.

  10. Start of the international tokamak physics activity

    International Nuclear Information System (INIS)

    Campbell, D.

    2001-01-01

    This newsletter comprises a summary on the start of the International Tokamak Physics activity (ITPA) by Dr. D. Campbell, Chair of the ITPA Co-ordinating Committee. As the ITER EDA drew to a close, it became clear that it was desirable to establish a new mechanism in order to promote the continued development of the physics basis for burning plasma experiments and to preserve the invaluable collaborations between the major international fusion communities which had been established through the ITER physics expert groups. As a result of the discussions of the representatives of the European Union, Japan, the Russian Federation and the United States the agreed principles for conducting the International Tokamak Physics Activity (ITPA) were elaborated and ITPA topical physics groups were organized

  11. Getting started with LevelDB

    CERN Document Server

    Dent, Andy

    2013-01-01

    The book is a concise guide for using LevelDB. It explains database concepts and the use of C++, ranging from the basics all the way to high level topics in an easy to follow, step-by-step format.The book is meant for developers who want an embedded database for their applications. Experienced programmers can pick up on the sophisticated data mapping patterns and tuning tips.Getting Started with LevelDB requires a minimal background in programming in C++ or Objective-C for OS/X or iOS and familiarity with XCode. Therefore it teaches enough C++ to use LevelDB without presuming any C++ knowledge

  12. [How to start a neuroimaging study].

    Science.gov (United States)

    Narumoto, Jin

    2012-06-01

    In order to help researchers understand how to start a neuroimaging study, several tips are described in this paper. These include 1) Choice of an imaging modality, 2) Statistical method, and 3) Interpretation of the results. 1) There are several imaging modalities available in clinical research. Advantages and disadvantages of each modality are described. 2) Statistical Parametric Mapping, which is the most common statistical software for neuroimaging analysis, is described in terms of parameter setting in normalization and level of significance. 3) In the discussion section, the region which shows a significant difference between patients and normal controls should be discussed in relation to the neurophysiology of the disease, making reference to previous reports from neuroimaging studies in normal controls, lesion studies and animal studies. A typical pattern of discussion is described.

  13. Start-up Strategy for Continuous Bioreactors

    Directory of Open Access Journals (Sweden)

    A.C. da Costa

    1997-06-01

    Full Text Available Abstract - The start-up of continuous bioreactors is solved as an optimal control problem. The choice of the dilution rate as the control variable reduces the dimension of the system by making the use of the global balance equation unnecessary for the solution of the optimization problem. Therefore, for systems described by four or less mass balance equations, it is always possible to obtain an analytical expression for the singular arc as a function of only the state variables. The steady state conditions are shown to satisfy the singular arc expression and, based on this knowledge, a feeding strategy is proposed which leads the reactor from an initial state to the steady state of maximum productivity

  14. Re-starting an Arnoldi iteration

    Energy Technology Data Exchange (ETDEWEB)

    Lehoucq, R.B. [Argonne National Lab., IL (United States)

    1996-12-31

    The Arnoldi iteration is an efficient procedure for approximating a subset of the eigensystem of a large sparse n x n matrix A. The iteration produces a partial orthogonal reduction of A into an upper Hessenberg matrix H{sub m} of order m. The eigenvalues of this small matrix H{sub m} are used to approximate a subset of the eigenvalues of the large matrix A. The eigenvalues of H{sub m} improve as estimates to those of A as m increases. Unfortunately, so does the cost and storage of the reduction. The idea of re-starting the Arnoldi iteration is motivated by the prohibitive cost associated with building a large factorization.

  15. Monitoring Start of Season in Alaska

    Science.gov (United States)

    Robin, J.; Dubayah, R.; Sparrow, E.; Levine, E.

    2006-12-01

    In biomes that have distinct winter seasons, start of spring phenological events, specifically timing of budburst and green-up of leaves, coincides with transpiration. Seasons leave annual signatures that reflect the dynamic nature of the hydrologic cycle and link the different spheres of the Earth system. This paper evaluates whether continuity between AVHRR and MODIS normalized difference vegetation index (NDVI) is achievable for monitoring land surface phenology, specifically start of season (SOS), in Alaska. Additionally, two thresholds, one based on NDVI and the other on accumulated growing degree-days (GDD), are compared to determine which most accurately predicts SOS for Fairbanks. Ratio of maximum greenness at SOS was computed from biweekly AVHRR and MODIS composites for 2001 through 2004 for Anchorage and Fairbanks regions. SOS dates were determined from annual green-up observations made by GLOBE students. Results showed that different processing as well as spectral characteristics of each sensor restrict continuity between the two datasets. MODIS values were consistently higher and had less inter-annual variability during the height of the growing season than corresponding AVHRR values. Furthermore, a threshold of 131-175 accumulated GDD was a better predictor of SOS for Fairbanks than a NDVI threshold applied to AVHRR and MODIS datasets. The NDVI threshold was developed from biweekly AVHRR composites from 1982 through 2004 and corresponding annual green-up observations at University of Alaska-Fairbanks (UAF). The GDD threshold was developed from 20+ years of historic daily mean air temperature data and the same green-up observations. SOS dates computed with the GDD threshold most closely resembled actual green-up dates observed by GLOBE students and UAF researchers. Overall, biweekly composites and effects of clouds, snow, and conifers limit the ability of NDVI to monitor phenological changes in Alaska.

  16. Hydrogen energy network start-up scenario

    International Nuclear Information System (INIS)

    Weingartner, S.; Ellerbrock, H.

    1994-01-01

    Hydrogen is widely discussed as future fuel and energy storage medium either to replace conventional fuels for automobiles, aircrafts and ships or to avoid the necessity of bulky battery systems for electricity storage, especially in connection with solar power systems. These discussions however started more than 25 years ago and up to now hydrogen has failed to achieve a major break-through towards wider application as energy storage medium in civil markets. The main reason is that other fuels are cheaper and very well implemented in our daily life. A study has been performed at Deutsche Aerospace in order to evaluate the boundary conditions, either political or economical, which would give hydrogen the necessary push, i.e. advantage over conventional fuels. The main goal of this study was to identify critical influence factors and specific start-up scenarios which would allow an economical and practically realistic use of hydrogen as fuel and energy medium in certain niche markets outside the space industry. Method and major results of this study are presented in detail in the paper. Certain niche markets could be identified, where with little initial governmental support, either by funding, tax laws or legislation, hydrogen can compete with conventional fuels. This however requires a scenario where a lot of small actions have to be taken by a high variety of institutions and industries which today are not interconnected with each other, i.e. it requires a new cooperative and proactive network between e.g. energy utilities, car industries, those who have a sound experience with hydrogen (space industry, chemical industry) and last, but certainly not the least, the government. Based on the developed scenario precise recommendations are drawn as conclusions

  17. 46 CFR 112.50-3 - Hydraulic starting.

    Science.gov (United States)

    2010-10-01

    ... POWER SYSTEMS Emergency Diesel and Gas Turbine Engine Driven Generator Sets § 112.50-3 Hydraulic starting. A hydraulic starting system must meet the following: (a) The hydraulic starting system must be a... 46 Shipping 4 2010-10-01 2010-10-01 false Hydraulic starting. 112.50-3 Section 112.50-3 Shipping...

  18. Application of intelligent soft start in asynchronous motor

    Science.gov (United States)

    Du, Xue; Ye, Ying; Wang, Yuelong; Peng, Lei; Zhang, Suying

    2018-05-01

    The starting way of three phase asynchronous motor has full voltage start and step-down start. Direct starting brings large current impact, causing excessive local temperature to the power grid and larger starting torque will also impact the motor equipment and affect the service life of the motor. Aim at the problem of large current and torque caused by start-up, an intelligent soft starter is proposed. Through the application of intelligent soft start on asynchronous motor, highlights its application advantage in motor control.

  19. Photoemission starting of induction rf-driven multicusp ion sources

    International Nuclear Information System (INIS)

    Pickard, D.S.; Leung, K.N.; Perkins, L.T.; Ponce, D.M.; Young, A.T.

    1996-01-01

    It has been demonstrated that pulsed and continuous wave, rf-driven hydrogen discharges can be started with photoemission. The extracted H - current from a photoemission-started plasma has been investigated and does not differ significantly from that of a filament-started plasma. The minimum pressure for photoemissive starting was found to be higher than that of filament starting, 17 mTorr compared to 7 mTorr, respectively, in this particular configuration. copyright 1996 American Institute of Physics

  20. Spreading continents kick-started plate tectonics.

    Science.gov (United States)

    Rey, Patrice F; Coltice, Nicolas; Flament, Nicolas

    2014-09-18

    Stresses acting on cold, thick and negatively buoyant oceanic lithosphere are thought to be crucial to the initiation of subduction and the operation of plate tectonics, which characterizes the present-day geodynamics of the Earth. Because the Earth's interior was hotter in the Archaean eon, the oceanic crust may have been thicker, thereby making the oceanic lithosphere more buoyant than at present, and whether subduction and plate tectonics occurred during this time is ambiguous, both in the geological record and in geodynamic models. Here we show that because the oceanic crust was thick and buoyant, early continents may have produced intra-lithospheric gravitational stresses large enough to drive their gravitational spreading, to initiate subduction at their margins and to trigger episodes of subduction. Our model predicts the co-occurrence of deep to progressively shallower mafic volcanics and arc magmatism within continents in a self-consistent geodynamic framework, explaining the enigmatic multimodal volcanism and tectonic record of Archaean cratons. Moreover, our model predicts a petrological stratification and tectonic structure of the sub-continental lithospheric mantle, two predictions that are consistent with xenolith and seismic studies, respectively, and consistent with the existence of a mid-lithospheric seismic discontinuity. The slow gravitational collapse of early continents could have kick-started transient episodes of plate tectonics until, as the Earth's interior cooled and oceanic lithosphere became heavier, plate tectonics became self-sustaining.

  1. Impulsively started, steady and pulsated annular inflows

    Energy Technology Data Exchange (ETDEWEB)

    Abdel-Raouf, Emad [General Field Engineer, Halliburton Energy Services 719 Hangar Dr, New Iberia, LA 70560, United States of America (United States); Sharif, Muhammad A R; Baker, John, E-mail: abdelraouf.em@gmail.com, E-mail: msharif@eng.ua.edu, E-mail: john.baker@eng.ua.edu [Aerospace Engineering and Mechanics Department, The University of Alabama, Tuscaloosa, Alabama 35487, United States of America (United States)

    2017-04-15

    A computational investigation was carried out on low Reynolds number laminar inflow starting annular jets using multiple blocking ratios and atmospheric ambient conditions. The jet exit velocity conditions are imposed as steady, unit pulsed, and sinusoidal pulsed while the jet surroundings and the far-field jet inlet upstream conditions are left atmospheric. The reason is to examine the flow behavior in and around the jet inlet under these conditions. The pulsation mode behavior is analyzed based on the resultant of the momentum and pressure forces at the entry of the annulus, the circulation and vortex formation, and the propulsion efficiency of the inflow jets. The results show that under certain conditions, the net force of inflow jets (sinusoidal pulsed jets in particular) could point opposite to the flow direction due to the adverse pressure drops in the flow. The propulsion efficiency is also found to increase with pulsation frequency and the sinusoidal pulsed inflow jets are more efficient than the unit pulsed inflow jets. In addition, steady inflow jets did not trigger the formation of vortices, while unit and sinusoidal pulsed inflow jets triggered the formation of vortices under a certain range of frequencies. (paper)

  2. Starting manufacturing phase of ITER upper ports

    Energy Technology Data Exchange (ETDEWEB)

    Utin, Yuri, E-mail: yuri.utin@iter.org [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Alekseev, Alexander; Sborchia, Carlo; Choi, Changho; Albin, Vincent; Barabash, Vladimir; Davis, James [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Fabritsiev, Sergey [NTC Sintez, Efremov Inst., 189631 Metallostroy, St. Petersburg (Russian Federation); Giraud, Benoit; Guirao, Julio [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Koenig, Werner [MAN Diesel & Turbo SE, Werftstrasse 17, Deggendorf (Germany); Kedrov, Igor; Kuzmin, Evgeny [NTC Sintez, Efremov Inst., 189631 Metallostroy, St. Petersburg (Russian Federation); Levesy, Bruno; Martinez, Jean-Marc [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Prebeck, Markus [MAN Diesel & Turbo SE, Werftstrasse 17, Deggendorf (Germany); Privalova, Elena [NTC Sintez, Efremov Inst., 189631 Metallostroy, St. Petersburg (Russian Federation); Ranzinger, Franz [MAN Diesel & Turbo SE, Werftstrasse 17, Deggendorf (Germany); Savrukhin, Petr [Russian Federation ITER Domestic Agency, Kurchatov sq.1, 123182 Moscow (Russian Federation); Schiller, Thomas [MAN Diesel & Turbo SE, Werftstrasse 17, Deggendorf (Germany); and others

    2015-10-15

    Highlights: • The port plugs are attached to the ports with high-strength fasteners. • Tightening of the fasteners via inductive heating was tested. • A concept for the port/plug sealing with metal-type gaskets has progressed. • Manufacturing design of the Upper Ports is in progress. • A full-scale mock-up of double-wall part of the port stub extension is in manufacturing process – acceptable final tolerances are expected. - Abstract: The ITER Vacuum Vessel (VV) features upper, equatorial and lower ports. The upper and regular equatorial ports are occupied by the port plugs. Although the port design has been overall completed in the past, the design of some remaining interfaces was still in progress: in particular, the Sealing Flange package, which includes the high-vacuum seals and the plug fasteners. As the ITER construction phase has started, the procurement of the VV ports has been launched. The VV upper ports will be procured by the Russian Federation Domestic Agency. The main suppliers were selected and the manufacturing design of the first parts is in full progress now. Since the VV is classified at nuclear level N2, the design and manufacture of its components are to be compliant with the French RCC-MR code and regulations for nuclear pressure equipment in France. These regulations make a strong impact to the port design and manufacturing process.

  3. Starting manufacturing phase of ITER upper ports

    International Nuclear Information System (INIS)

    Utin, Yuri; Alekseev, Alexander; Sborchia, Carlo; Choi, Changho; Albin, Vincent; Barabash, Vladimir; Davis, James; Fabritsiev, Sergey; Giraud, Benoit; Guirao, Julio; Koenig, Werner; Kedrov, Igor; Kuzmin, Evgeny; Levesy, Bruno; Martinez, Jean-Marc; Prebeck, Markus; Privalova, Elena; Ranzinger, Franz; Savrukhin, Petr; Schiller, Thomas

    2015-01-01

    Highlights: • The port plugs are attached to the ports with high-strength fasteners. • Tightening of the fasteners via inductive heating was tested. • A concept for the port/plug sealing with metal-type gaskets has progressed. • Manufacturing design of the Upper Ports is in progress. • A full-scale mock-up of double-wall part of the port stub extension is in manufacturing process – acceptable final tolerances are expected. - Abstract: The ITER Vacuum Vessel (VV) features upper, equatorial and lower ports. The upper and regular equatorial ports are occupied by the port plugs. Although the port design has been overall completed in the past, the design of some remaining interfaces was still in progress: in particular, the Sealing Flange package, which includes the high-vacuum seals and the plug fasteners. As the ITER construction phase has started, the procurement of the VV ports has been launched. The VV upper ports will be procured by the Russian Federation Domestic Agency. The main suppliers were selected and the manufacturing design of the first parts is in full progress now. Since the VV is classified at nuclear level N2, the design and manufacture of its components are to be compliant with the French RCC-MR code and regulations for nuclear pressure equipment in France. These regulations make a strong impact to the port design and manufacturing process.

  4. Morphological, Thermal, Electrical and Electromechanical Properties of Polyvinylidene Fluoride (PVDF)-Functionalized Carbon Nanotube Composites (Preprint)

    Science.gov (United States)

    2012-03-01

    several times with deionized water and ethanol to remove undissolved chemicals. Finally the solution was filtered through 0.2 µm cellulose nitrate...was recorded for 3 times and average was used. To observe the morphology of the synthesized samples, FESEM (Quanta 3D ) was performed. Powder was...linear within elastic region and start going to plastic region with further increment in load. For testing electromechanical properties of these f-CNT

  5. Nuclear power: time to start again

    International Nuclear Information System (INIS)

    Rezak, W.D.

    2004-01-01

    This paper presents data which support the construction and operating successes enjoyed by energy companies that operate nuclear power plants in the US. The result is that the US nuclear industry is alive and well. Perhaps it's time to start anew the building of nuclear power plants. Over 20% of the electricity generated in the United States comes from nuclear power plants. An adequate, reliable supply of reasonably priced electric energy is not a consequence of an expanding economy and gross national product; it is an absolute necessity before such expansion can occur. It is hard to imagine any aspect of our business or personal lives not, in some way, dependent upon electricity. All over the world (in over 30 countries) nuclear power is a low-cost, secure, safe, dependable, and environmentally friendly form of electric power generation. Nuclear plants in these countries are built in six to eight years using technology developed in the US, with good performance and safety records. This treatise addresses the success experienced by the US nuclear industry over the last 40 years, and makes the case that this reliable, cost-competitive source of electric power can help support the economic engine of the country and help prevent experiences like the recent crises in California and the Northeast. Successful operation of nuclear facilities is determined by examining capacity or load factors. Load factor is the percentage of design generating capacity that a power plant actually produces over the course of a year's operation. This paper makes the case that these operating performance indicators warrant renewed consideration of the nuclear option. Usage of electricity in the US now approaches total generating capacity. The Nuclear Regulatory Commission has pre-approved construction and operating licenses for several nuclear plant designs. State public service commissions are beginning to understand that dramatic reform is required. The economy is recovering and inflation

  6. Starting up microbial enhanced oil recovery.

    Science.gov (United States)

    Siegert, Michael; Sitte, Jana; Galushko, Alexander; Krüger, Martin

    2014-01-01

    This chapter gives the reader a practical introduction into microbial enhanced oil recovery (MEOR) including the microbial production of natural gas from oil. Decision makers who consider the use of one of these technologies are provided with the required scientific background as well as with practical advice for upgrading an existing laboratory in order to conduct microbiological experiments. We believe that the conversion of residual oil into natural gas (methane) and the in situ production of biosurfactants are the most promising approaches for MEOR and therefore focus on these topics. Moreover, we give an introduction to the microbiology of oilfields and demonstrate that in situ microorganisms as well as injected cultures can help displace unrecoverable oil in place (OIP). After an initial research phase, the enhanced oil recovery (EOR) manager must decide whether MEOR would be economical. MEOR generally improves oil production but the increment may not justify the investment. Therefore, we provide a brief economical assessment at the end of this chapter. We describe the necessary state-of-the-art scientific equipment to guide EOR managers towards an appropriate MEOR strategy. Because it is inevitable to characterize the microbial community of an oilfield that should be treated using MEOR techniques, we describe three complementary start-up approaches. These are: (i) culturing methods, (ii) the characterization of microbial communities and possible bio-geochemical pathways by using molecular biology methods, and (iii) interfacial tension measurements. In conclusion, we hope that this chapter will facilitate a decision on whether to launch MEOR activities. We also provide an update on relevant literature for experienced MEOR researchers and oilfield operators. Microbiologists will learn about basic principles of interface physics needed to study the impact of microorganisms living on oil droplets. Last but not least, students and technicians trying to understand

  7. Technological start of T-15 tokamak. The start-up diagnostic complex

    International Nuclear Information System (INIS)

    Notkin, G.E.

    1989-01-01

    The T-15 tokamak with superconducting toroidal winding reached the technological start-up phase. The results of the first operating tests of the main tokamak components are reported. Due to improper function of both the vacuum and the cryogenic system, the nominal parameters of the vacuum and of the toroidal magnetic field have not been achieved. The non-optimum vacuum conditions made the discharge start-up difficult even when a pre-ionizing electron beam and a gyrotron generator were used. The pre-discharge plasma parametes were studied by means of a limited set of plasma diagnostic apparatus. Due to substantially deteriorated vacuum conditions, it was not possible to repeat the only one successful discharge with a current of 100 kA, lasting for 50 ms. (J.U.)

  8. Quantifying climate risk - the starting point

    International Nuclear Information System (INIS)

    Fairweather, Helen; Luo, Qunying; Liu, De Li; Wiles, Perry

    2007-01-01

    Full text: All natural systems have evolved to their current state as a result inter alia of the climate in which they developed. Similarly, man-made systems (such as agricultural production) have developed to suit the climate experienced over the last 100 or so years. The capacity of different systems to adapt to changes in climate that are outside those that have been experienced previously is largely unknown. This results in considerable uncertainty when predicting climate change impacts. However, it is possible to quantify the relative probabilities of a range of potential impacts of climate change. Quantifying current climate risks is an effective starting point for analysing the probable impacts of future climate change and guiding the selection of appropriate adaptation strategies. For a farming system to be viable within the current climate, its profitability must be sustained and, therefore, possible adaptation strategies need to be tested for continued viability in a changed climate. The methodology outlined in this paper examines historical patterns of key climate variables (rainfall and temperature) across the season and their influence on the productivity of wheat growing in NSW. This analysis is used to identify the time of year that the system is most vulnerable to climate variation, within the constraints of the current climate. Wheat yield is used as a measure of productivity, which is also assumed to be a surrogate for profitability. A time series of wheat yields is sorted into ascending order and categorised into five percentile groupings (i.e. 20th, 40th, 60th and 80th percentiles) for each shire across NSW (-100 years). Five time series of climate data (which are aggregated daily data from the years in each percentile) are analysed to determine the period that provides the greatest climate risk to the production system. Once this period has been determined, this risk is quantified in terms of the degree of separation of the time series

  9. Pakistan/USAID to start CSM project.

    Science.gov (United States)

    1984-01-01

    Pakistan, with the assistance of funds for the US Agency for International Development (USAID), is about to start its novel approach to contraceptive social marketing (CSM). This new effort suggests a marked policy shift on the part of the Pakistan government toward intensifying its family planning activities. The program will be government-operated and supported by AID over the next 5 years with $20 million, more than double the cost of similar CSM projects elswhere. Distribution of a condom on a pilot project basis is expected to begin by December 1984. Sales of a low-dose oral contraceptive (OC) could begin in test market areas by mid-1985, with national launching of both products tentatively scheduled for January 1986. The Pakistan/USAID agreement represents the 1st time since the formation of India's Nirodh project in the late 1960s that a CSM program is being established without the involvement of either an international social marketing contractor or a country's family planning association. The Pakistan CSM program will be managed by a policy board composed of representatives from the government's Ministries of Planning, Health and Education; a resident advisor from USAID; and a local company responsible for product marketing and distribution. The approach has received a skeptical response among international social marketing experts about the program's chances for success. Their doubts extend to 2 other aspects of the proposed design: an official of the Ministry of Planning's Population and Welfare Division expects the CSM program to generate sufficient revenues to cover all operating costs following the 5-year subsidy period, while also providing attractive profit margins for the marketing/distribution company; and the government prohibits mass media advertising of contraceptives. According to AID, the issue of mass media contraceptive advertising has not yet been resolved, and a national survey will be conducted to determine what communication needs are

  10. Canola meal on starting pigs feeding

    Directory of Open Access Journals (Sweden)

    Lina Maria Peñuela-Sierra

    2015-12-01

    Full Text Available Three experiments were carried out to determine the nutritional values and evaluate the performance of piglets fed on canola meal. In experiment I, a digestibility assay was conducted using fourteen barrow pigs, with an initial body weight of 20.62±3.30 kg. The evaluated feedstuff was canola meal, with a level of 250 g/kg in the basal diet (corn + soybean meal-based. The experimental unit consisted of one pig, with a total of seven experimental units per diet. The values as (fed basis of digestible (DE and metabolizable (ME energy of canola meal were 2,995 kcal/kg and 2,796 kcal/kg, respectively. In experiment II, ileal digestibility assays were carried out to determine the apparent and true ileal digestibility coefficient and digestible amino acids. Three crossbred pigs were used, with a BW of 38.6±1.98 kg. The treatments consisted of two diets, with a single source of protein (canola meal and one protein-free diet (OFD. The values of digestible amino acids in canola meal were as follows: lysine: 11.8 g/kg; methionine+cystine: 9.1 g/kg; threonine: 7.9 g/kg; tryptophan: 2.4 g/kg; leucine: 15.7 g/kg; and isoleucine: 8.7 g/kg. In experiment III, 60 piglets (BW= 15.08±0.72 kg to 30.26±2.78 kg were allotted in a completely randomized design. The treatments consisted of four diets with increasing levels of canola meal (50, 100, 150 and 200 g/kg, six replicates and experimental unit consisted of two pigs. Additionally, a control diet was formulated containing 0.0 g/kg CM. Regression analysis indicates that there was no effect (P?0.05 of the level of canola meal inclusion on pigs performance. The performance results suggest that it is feasible to use up to 200 g/kg of canola meal in starting pigs diet, without impairing performance and the feeding cost.

  11. Multigenerational Head Start Participation: An Unexpected Marker of Progress

    Science.gov (United States)

    Chor, Elise

    2018-01-01

    One-quarter of the Head Start population has a mother who participated in the program as a child. This study uses experimental Head Start Impact Study (HSIS) data on 3- and 4-year-olds (N = 2,849) to describe multigenerational Head Start families and their program experiences. In sharp contrast to full-sample HSIS findings, Head Start has large,…

  12. Enhancing start performance in the sport of skeleton

    OpenAIRE

    Colyer, Steffi

    2015-01-01

    A fast start is considered to be crucial in skeleton with marginal gains in start performance perceived to make meaningful improvements to overall chances of success. Currently, knowledge surrounding the underlying determinants of start performance is sparse and training practices are based on limited scientific evidence. A series of investigations were conducted to advance this understanding.Initial observations revealed similarities between dry-land push-starts and those on ice tracks. Howe...

  13. Making a Simple Self-Starting Electric Motor

    Science.gov (United States)

    Hong, Seok-In; Choi, Jung-In; Hong, Seok-Cheol

    2009-01-01

    A simple electric motor has a problem in that the current applied to the motor per se can rarely trigger its rotation. Usually such motors begin to rotate after the rotor is slightly turned by hand (i.e., manual starting). In a "self-starting" motor, the rotor starts to rotate spontaneously as soon as the current is applied. This paper describes…

  14. Head Start Participants, Programs, Families and Staff in 2013

    Science.gov (United States)

    Walker, Christina

    2014-01-01

    Head Start programs provide poor children and their families with comprehensive early education and support services. Each year, programs are required to submit a Program Information Report (PIR) to the Office of Head Start on participating children, pregnant women, and families, as well as the staff serving the Head Start population. In 2013, the…

  15. The Role of Classroom Quality in Explaining Head Start Impacts

    Science.gov (United States)

    Connors, Maia C.; Friedman-Krauss, Allison H.; Morris, Pamela A.; Page, Lindsay C.; Feller, Avi

    2014-01-01

    This study seeks to answer the following question: Are impacts on Head Start classroom quality associated with impacts of Head Start on children's learning and development? This study employs a variety of descriptive and quasi-experimental methods to explore the role of classroom quality as a mediator or mechanism of Head Start impacts. This…

  16. Do Head Start Impacts Vary by Neighborhood Context?

    Science.gov (United States)

    Morris, Pamela A.; Connors, Maia C.; McCoy, Dana Charles; Gomez, Celia J.; Yoshikawa, Hiro; Aber, J. Lawrence

    2014-01-01

    This paper capitalizes on the addition of geocodes for Head Start centers in which children were randomly assigned to address questions about the role of neighborhood characteristics in moderating impacts of assignment to the Head Start program. Researchers explore the extent to which impacts of assignment to Head Start on outcomes for children…

  17. Head Start Instructional Professionals' Inclusion Perceptions and Practices

    Science.gov (United States)

    Muccio, Leah S.; Kidd, Julie K.; White, C. Stephen; Burns, M. Susan

    2014-01-01

    This study considered the facilitators and barriers of successful inclusion in Head Start classrooms by examining the perspectives and practices of instructional professionals. A cross-sectional survey design was combined with direct observation in inclusive Head Start classrooms. Survey data were collected from 71 Head Start instructional…

  18. Enhancing Early Childhood Outcomes: Connecting Child Welfare and Head Start

    Science.gov (United States)

    McCrae, Julie S.; Brown, Samantha M.; Yang, Jessica; Groneman, Sheila

    2016-01-01

    Head Start is a preschool program for families with low incomes and nearly 85% of child welfare-involved families are low-income, yet little is known about Head Start and child welfare collaboration. This study uses data from 28 Head Start directors to describe collaboration facilitators and barriers, and collaborative mechanisms in place. The…

  19. Experience in the Kola NPP start-up works

    International Nuclear Information System (INIS)

    Zakharov, S.I.; Omel'chuk, V.V.; Bodrukhin, Yu.M.

    1984-01-01

    Main stages and peculiar features of maintenance and start-up works at WWER-440 type reactor NPPs described. Remarks revealed during complex equipment testing, physical and power start-up will be useful for arrangement of maintenance and start-up works at newly built NPPs

  20. Personal and Public Start Pages in a library setting

    NARCIS (Netherlands)

    Kieft-Wondergem, Dorine

    Personal and Public Start Pages are web-based resources. With these kind of tools it is possible to make your own free start page. A Start Page allows you to put all your web resources into one page, including blogs, email, podcasts, RSSfeeds. It is possible to share the content of the page with

  1. Soft-Starting Power-Factor Motor Controller

    Science.gov (United States)

    Nola, F. J.

    1983-01-01

    Three-phase power-factor controller with soft start is based on earlier version that does not control starting transients. Additional components serve to turn off "run" command signal and substitute gradual startup command signal during preset startup interval. Improved controller reduces large current surge that usually accompanies starting. Controller applies power smoothly, without causing motor vibrations.

  2. 40 CFR 86.536-78 - Engine starting and restarting.

    Science.gov (United States)

    2010-07-01

    ... equipped with automatic chokes shall be operated according to the instructions in the manufacturer's... transmission shall be placed in gear 15 seconds after the engine is started. If necessary, braking may be... starting procedure, the engine (automatic and manual choke engines) shall be started by opening the...

  3. 76 FR 50813 - Major Capital Investment Projects; Guidance on News Starts/Small Starts Policies and Procedures

    Science.gov (United States)

    2011-08-16

    ... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Major Capital Investment Projects; Guidance on News Starts/Small Starts Policies and Procedures AGENCY: Federal Transit Administration (FTA... Administration (FTA) to publish policy guidance on the New and Small Starts capital project review and evaluation...

  4. A QCQP Approach for OPF in Multiphase Radial Networks with Wye and Delta Connections: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Zamzam, Ahmed, S.; Zhaoy, Changhong; Dall' Anesey, Emiliano; Sidiropoulos, Nicholas D.

    2017-06-27

    This paper examines the AC Optimal Power Flow (OPF) problem for multiphase distribution networks featuring renewable energy resources (RESs). We start by outlining a power flow model for radial multiphase systems that accommodates wye-connected and delta-connected RESs and non-controllable energy assets. We then formalize an AC OPF problem that accounts for both types of connections. Similar to various AC OPF renditions, the resultant problem is a non convex quadratically-constrained quadratic program. However, the so-called Feasible Point Pursuit-Successive Convex Approximation algorithm is leveraged to obtain a feasible and yet locally-optimal solution. The merits of the proposed solution approach are demonstrated using two unbalanced multiphase distribution feeders with both wye and delta connections.

  5. Empirical Investigations of the Opportunity Limits of Automatic Residential Electric Load Shaping: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Cruickshank, Robert F.; Henze, Gregor P.; Balaji, Rajagopalan; Hodge, Bri-Mathias S.; Florita, Anthony R.

    2017-04-01

    Residential electric load shaping is often modeled as infrequent, utility-initiated, short-duration deferral of peak demand through direct load control. In contrast, modeled herein is the potential for frequent, transactive, intraday, consumer-configurable load shaping for storage-capable thermostatically controlled electric loads (TCLs), including refrigerators, freezers, and hot water heaters. Unique to this study are 28 months of 15-minute-interval observations of usage in 101 homes in the Pacific Northwest United States that specify exact start, duration, and usage patterns of approximately 25 submetered loads per home. The magnitudes of the load shift from voluntarily-participating TCL appliances are aggregated to form hourly upper and lower load-shaping limits for the coordination of electrical generation, transmission, distribution, storage, and demand. Empirical data are statistically analyzed to define metrics that help quantify load-shaping opportunities.

  6. Are the new starting block facilities beneficial for backstroke start performance?

    Science.gov (United States)

    de Jesus, Karla; de Jesus, Kelly; Abraldes, J Arturo; Medeiros, Alexandre Igor Araripe; Fernandes, Ricardo J; Vilas-Boas, João Paulo

    2016-01-01

    We aimed to analyse the handgrip positioning and the wedge effects on the backstroke start performance and technique. Ten swimmers completed randomly eight 15 m backstroke starts (four with hands on highest horizontal and four on vertical handgrip) performed with and without wedge. One surface and one underwater camera recorded kinematic data. Standardised mean difference (SMD) and 95% confidence intervals (CI) were used. Handgrip positioning did not affect kinematics with and without wedge use. Handgrips horizontally positioned and feet over wedge displayed greater knee angular velocity than without it (SMD = -0.82; 95% CI: -1.56, -0.08). Hands vertically positioned and feet over wedge presented greater take-off angle (SMD = -0.81; 95% CI: -1.55, -0.07), centre of mass (CM) vertical positioning at first water contact (SMD = -0.97; 95% CI: -1.87, -0.07) and CM vertical velocity at CM immersion (SMD = 1.03; 95% CI: 0.08, 1.98) when comparing without wedge use. Swimmers extended the hip previous to the knee and ankle joints, except for the variant with hands vertically positioned without wedge (SMD = 0.75; 95% CI: -0.03, 1.53). Swimmers should preserve biomechanical advantages achieved during flight with variant with hands vertically positioned and wedge throughout entry and underwater phase.

  7. Modelling ohmic confinement experiments on the START tokamak

    International Nuclear Information System (INIS)

    Roach, C.M.

    1996-05-01

    Ohmic confinement data from the tight aspect ratio tokamak START has been analysed using the ASTRA transport simulation code. Neoclassical expressions have been modified to describe tight aspect ratio configurations, and the comparison between START data and models of anomalous transport has been made quantitative using the standard χ 2 test from statistics. Four confinement models (T11, Rebut-Lallia-Watkins, Lackner-Gottardi, and Taroni et al's Bohm model) have been compared with the START data. Three of the models are found to simulate START's electron temperature data moderately well, while Taroni et al's Bohm model overestimates electron temperatures in START by an order of magnitude. Thus comparison with START data tends to discriminate against Bohm models; these models are pessimistic or ITER. (author)

  8. Sleep, sleepiness and school start times: a preliminary study.

    Science.gov (United States)

    Dexter, Donn; Bijwadia, Jagdeep; Schilling, Dana; Applebaugh, Gwendolyn

    2003-01-01

    High school students are reported to be excessively sleepy, resulting in decreased academic performance, increased psycho-social problems and increased risk of morbidity and mortality from accidents. Early school start times have been noted to contribute to this problem. This report attempts to confirm the relationship of early school start times with decreased sleep and increased sleepiness. We examined sophomore and junior students in 2 local high schools with different start times and measured the amount of time slept and sleepiness. We found that students at the early start school reported reduced sleep time and more sleepiness than their counterparts at the later starting school. Early school start times are associated with student reports of less sleep and increased sleepiness. Further studies in larger groups are recommended in view of the potential significant impact of sleep deprivation in this age group.

  9. Linking Environmental Orientation to Start-ups’ Networking Activities

    DEFF Research Database (Denmark)

    Dickel, Petra; Ritter, Thomas

    Besides for-profit start-ups, an increasing number of firms start their existence with the purpose to “do good” for society – mirrored in an increasing academic discussion of sustainable firms. Yet, there is little research on the networking activities of start-ups that do not have profit...... generation as their primary focus. Addressing this research gap, we develop hypotheses on the different networking activities of environmentally oriented start-ups arguing that their societal focus has a positive impact on the frequency of their networking and the size of their network. For empirically...... investigating such networking differences, we use data from 179 technology-based start-ups and show that start-ups with a strong external environmental orientation have significantly higher networking frequency and build larger networks. On the contrary, strong internal environmental orientation is linked...

  10. Start-up simulations of the PULSAR pulsed tokamak reactor

    International Nuclear Information System (INIS)

    Werley, K.A.; Bathke, C.G.

    1993-01-01

    Start-up conditions are examined for a pulsed tokamak reactor that uses only inductively driven plasma current (and bootstrap current). A zero-dimensional (profile-averaged) model containing plasma power and particle balance equations is used to study several aspects of plasma start-up, including: (1) optimization of the start-up pathway; (2) tradeoffs of auxiliary start-up heating power versus start-up time; (3) volt-second consumption; (4) thermal stability of the operating point; (5) estimates of the diverter heat flux and temperature during the start-up transient; (6) the sensitivity of the available operating space to allowed values of the H confinement factor; and (7) partial-power operations

  11. Probabilistic Wind Power Ramp Forecasting Based on a Scenario Generation Method: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Qin [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Florita, Anthony R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Krishnan, Venkat K [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hodge, Brian S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Cui, Mingjian [Univ. of Texas-Dallas, Richardson, TX (United States); Feng, Cong [Univ. of Texas-Dallas, Richardson, TX (United States); Wang, Zhenke [Univ. of Texas-Dallas, Richardson, TX (United States); Zhang, Jie [Univ. of Texas-Dallas, Richardson, TX (United States)

    2017-08-31

    Wind power ramps (WPRs) are particularly important in the management and dispatch of wind power, and they are currently drawing the attention of balancing authorities. With the aim to reduce the impact of WPRs for power system operations, this paper develops a probabilistic ramp forecasting method based on a large number of simulated scenarios. An ensemble machine learning technique is first adopted to forecast the basic wind power forecasting scenario and calculate the historical forecasting errors. A continuous Gaussian mixture model (GMM) is used to fit the probability distribution function (PDF) of forecasting errors. The cumulative distribution function (CDF) is analytically deduced. The inverse transform method based on Monte Carlo sampling and the CDF is used to generate a massive number of forecasting error scenarios. An optimized swinging door algorithm is adopted to extract all the WPRs from the complete set of wind power forecasting scenarios. The probabilistic forecasting results of ramp duration and start time are generated based on all scenarios. Numerical simulations on publicly available wind power data show that within a predefined tolerance level, the developed probabilistic wind power ramp forecasting method is able to predict WPRs with a high level of sharpness and accuracy.

  12. Uncertainty Analysis of OC5-DeepCwind Floating Semisubmersible Offshore Wind Test Campaign: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, Amy N [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-07-26

    This paper examines how to assess the uncertainty levels for test measurements of the Offshore Code Comparison, Continued, with Correlation (OC5)-DeepCwind floating offshore wind system, examined within the OC5 project. The goal of the OC5 project was to validate the accuracy of ultimate and fatigue load estimates from a numerical model of the floating semisubmersible using data measured during scaled tank testing of the system under wind and wave loading. The examination of uncertainty was done after the test, and it was found that the limited amount of data available did not allow for an acceptable uncertainty assessment. Therefore, this paper instead qualitatively examines the sources of uncertainty associated with this test to start a discussion of how to assess uncertainty for these types of experiments and to summarize what should be done during future testing to acquire the information needed for a proper uncertainty assessment. Foremost, future validation campaigns should initiate numerical modeling before testing to guide the test campaign, which should include a rigorous assessment of uncertainty, and perform validation during testing to ensure that the tests address all of the validation needs.

  13. Start up testing for the secure automated fabrication line

    International Nuclear Information System (INIS)

    Gerber, E.W.; Benson, E.M.; Dahl, R.E.

    1987-01-01

    The secure automated fabrication (SAF) line is a remotely operated, liquid metal reactor fuel fabrication process being built by Westinghouse Hanford Company for the Department of Energy. All process and control equipment is installed and start up testing has been initiated. Start up testing is comprised of five phases, each incorporating higher degrees of equipment integration, automation, and remote control. Testing methodology for SAF line start up is described in this report

  14. How to Start Growing Beef Calves on Feed

    OpenAIRE

    ZoBell, Dale R

    2003-01-01

    Starting calves on feed takes time and effort because of the stress young calves are susceptible to at this point in their lives. The reduction of stress will result in calves consuming more feed, thus remaining healthier. To successfully start calves on feed, dry matter intake must be maximized while minimizing health problems. The following is a 5-step applied method for starting calves on a silage-based ration.

  15. School Starting Age and the Crime-Age Profile

    DEFF Research Database (Denmark)

    Landersø, Rasmus; Nielsen, Helena Skyt; Simonsen, Marianne

    2017-01-01

    This paper uses register-based data to investigate the effects of school starting age on crime. Through this, we provide insights into the determinants of crime-age profiles. We exploit that Danish children typically start first grade in the calendar year they turn seven, which gives rise...... to a discontinuity in school starting age for children born around New Year. Our analysis speaks against a simple invariant crime-age profile as is popular in criminology: we find that higher school starting age lowers the propensity to commit crime at young ages. We also find effects on the number of crimes...

  16. De-escalatory confidence-building measures after START

    International Nuclear Information System (INIS)

    Stockton, P.N.

    1992-01-01

    The very notion of examining de-escalatory CBMs in the context of the START negotiations appears odd. Given the immense progress in US-Soviet relations, of which the proposed START agreement is emblematic, the risk of the two nations stumbling to the brink of war seems increasingly remote. Why bother analyzing CBMs designed to help resolve such an improbable event? The obvious answer is that relations between the US and the Soviet Union - or whatever array of nations succeed it - could take an unforeseeable turn for the worse. Once ratified, the START agreement is supposed to remain in force for seven years, more than enough time for political tensions to return with a vengeance. This suggests a more prudent question: if our two nations do stumble to the brink of war, will the START agreement affect the prospect of de-escalatory CBMs? And if the US and Soviet Union pursue deeper force-reductions in a follow-on START II agreement, could that agreement be designed to facilitate more effective de-escalatory measures? This paper sets the stage for addressing such questions by outlining the START agreement and offering a brief overview of how START might affect the prospects for CBMs. Then, after examining some specific CBM proposals in light of START, an analysis will be made of the de-escalatory problems and opportunities that a Start II treaty might create

  17. Cold starting characteristics analysis of hydraulic free piston engine

    International Nuclear Information System (INIS)

    Zhang, Shuanlu; Zhao, Zhenfeng; Zhao, Changlu; Zhang, Fujun; Wang, Shan

    2017-01-01

    The cold start characteristic of hydraulic free piston diesel engine may affect its stable operation. Therefore the specific cold start characteristics, such as BDC or TDC positions, pressure in-cylinder, heat release rate, should be investigated in detail. These parameters fluctuate in some regularity in the cod start process. With the development of the free piston engine prototype and the establishment of test bench, the results are obtained. For the dynamic results, the fluctuation range of TDC and BDC positions is 8 mm and decreases with time. The thermodynamic results show that the combustion process is not stable and the pressure in-cylinder fluctuates largely in the cold start process. In addition, the combustion is rapid and knock happens inevitably. In order to investigate the reasons, a CFD model is established for temperature analysis in-cylinder and heat transfer conditions. It is found that higher start wall temperature will lead to more uniform temperature distribution. The delay period may decreases and heat release will move forward. This reason is analyzed by thermodynamic derivation based on the first law of thermodynamics. Finally, the improvement suggestions of cold start strategy are proposed. - Highlights: • The cold start behaviors of HFPE are investigated in detail. • CFD method is used for simulating temperature distribution in start process. • Thermodynamic derivation uncovers the compression temperature distribution. • The improvement suggestions of cold start strategy are proposed.

  18. School Starting Age and the Crime-Age Profile

    OpenAIRE

    Landerso, Rasmus; Nielsen, Helena Skyt; Simonsen, Marianne

    2015-01-01

    This paper uses register-based data to investigate the effects of school starting age on crime. Through this, we provide insights into the determinants of crime-age profiles. We exploit that Danish children typically start first grade in the calendar year they turn seven, which gives rise to a discontinuity in school starting age for children born around New Year. Our analysis speaks against a simple invariant crime-age profile as is popular in criminology: we find that higher school starting...

  19. Product innovation and commercialization in lean global start-ups

    DEFF Research Database (Denmark)

    Tanev, Stoyan; Rasmussen, Erik Stavnsager; Zijdemans, Erik

    2015-01-01

    The paper examines the distinctive characteristics of product innovation and commercialization in Lean Global Start-up (LGS) – new technology firms which have adopted a lean and global path from or near to their inception. It suggests an uncertainty vs risk framework which allows integrating two...... research streams – Born Global (BG) firms and lean start-ups. In addition to its integrative theoretical value, the paper offers insights for lean start-up managers dealing with the challenges of a global start....

  20. Best Practices of Uncertainty Estimation for the National Solar Radiation Database (NSRDB 1998-2015): Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Habte, Aron M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Sengupta, Manajit [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-12-19

    It is essential to apply a traceable and standard approach to determine the uncertainty of solar resource data. Solar resource data are used for all phases of solar energy conversion projects, from the conceptual phase to routine solar power plant operation, and to determine performance guarantees of solar energy conversion systems. These guarantees are based on the available solar resource derived from a measurement station or modeled data set such as the National Solar Radiation Database (NSRDB). Therefore, quantifying the uncertainty of these data sets provides confidence to financiers, developers, and site operators of solar energy conversion systems and ultimately reduces deployment costs. In this study, we implemented the Guide to the Expression of Uncertainty in Measurement (GUM) 1 to quantify the overall uncertainty of the NSRDB data. First, we start with quantifying measurement uncertainty, then we determine each uncertainty statistic of the NSRDB data, and we combine them using the root-sum-of-the-squares method. The statistics were derived by comparing the NSRDB data to the seven measurement stations from the National Oceanic and Atmospheric Administration's Surface Radiation Budget Network, National Renewable Energy Laboratory's Solar Radiation Research Laboratory, and the Atmospheric Radiation Measurement program's Southern Great Plains Central Facility, in Billings, Oklahoma. The evaluation was conducted for hourly values, daily totals, monthly mean daily totals, and annual mean monthly mean daily totals. Varying time averages assist to capture the temporal uncertainty of the specific modeled solar resource data required for each phase of a solar energy project; some phases require higher temporal resolution than others. Overall, by including the uncertainty of measurements of solar radiation made at ground stations, bias, and root mean square error, the NSRDB data demonstrated expanded uncertainty of 17 percent - 29 percent on hourly

  1. Caregivers' attitudes regarding portion size served to Head Start children

    Science.gov (United States)

    The purpose of this study was to identify caregivers' attitudes regarding amounts and types of foods served to Head Start preschoolers using qualitative methods. Researchers conducted 8 focus groups (4 African American; 4 Hispanic) with 33 African American and 29 Hispanic Head Start caregivers. Mode...

  2. Head Start, 4 years After Completing the Program

    Science.gov (United States)

    Kim, Young-Joo

    2013-01-01

    This paper studies the effect of the Head Start program on children's achievements in reading and math tests during their first 4 years of schooling after completing the program. Using nationally representative data from the Early Childhood Longitudinal Study, I found large measurement error in the parental reports of Head Start attendance, which…

  3. Starting infants on antiretroviral therapy | Clayden | Southern African ...

    African Journals Online (AJOL)

    5 years or more, that most start at a late stage of the disease, and that mortality in the first few months of treatment remains high.5,6 A recent study shows that starting treatment in early infancy can be lifesaving, and this has informed revisions in World Health Organization (WHO) guidelines7,8 (see WHO 'Dear Health Care ...

  4. Head Start Impact Study. Final Report. Executive Summary

    Science.gov (United States)

    Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

    2010-01-01

    This report summarizes the findings from a study on the impacts of Head Start on children and families during the children's preschool, kindergarten, and 1st grade years. Its study goals were to: (1) Determine the impact of Head Start on children's school readiness, and on parental practices that support children's development; and to (2)…

  5. Early Head Start Participants, Programs, Families, and Staff in 2014

    Science.gov (United States)

    Mohan, Anitha; Walker, Christina

    2016-01-01

    In 1994, the federal Early Head Start (EHS) program was created to address the comprehensive needs of low-income pregnant women and children under age 3. EHS was launched almost 30 years after Head Start was established in 1965 to serve low-income 3- and 4-year-old children and their families with comprehensive early education and support…

  6. 46 CFR 112.50-5 - Electric starting.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Electric starting. 112.50-5 Section 112.50-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Diesel and Gas Turbine Engine Driven Generator Sets § 112.50-5 Electric starting...

  7. Starting an Actuarial Science Major at a Liberal Arts College

    Science.gov (United States)

    Mills, Mark A.

    2014-01-01

    The article provides details of the process of starting an actuarial science major at a small, liberal arts college. Some critique of the major is included, as well as some challenges that may be faced by others wanting to start such a major at their institution.

  8. 40 CFR 86.136-90 - Engine starting and restarting.

    Science.gov (United States)

    2010-07-01

    ... automatic chokes shall be operated according to the manufacturer's operating instructions in the owner's...) The transmission shall be placed in gear 15 seconds after the engine is started. If necessary, braking... instructions in the owner's manual do not specify a warm engine starting procedure, the engine (automatic and...

  9. Start-up Costs, Taxes and Innovative Entrepreneurship

    NARCIS (Netherlands)

    P. Darnihamedani (Pourya); J.H. Block (Jörn); S.J.A. Hessels (Jolanda); A. Simonyan (Aram)

    2015-01-01

    markdownabstract__Abstract__ Prior research suggests that start-up costs and taxes negatively influence entry into entrepreneurship. Yet, no distinction is made regarding the type of entrepreneurship, particularly innovative versus non-innovative entrepreneurship. Start-up costs, being one-off

  10. 13 CFR 305.11 - Contract awards; early construction start.

    Science.gov (United States)

    2010-01-01

    ... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Contract awards; early construction start. 305.11 Section 305.11 Business Credit and Assistance ECONOMIC DEVELOPMENT ADMINISTRATION... § 305.11 Contract awards; early construction start. EDA must determine that the award of all contracts...

  11. Beyond Intentions--What Makes a Student Start a Firm?

    Science.gov (United States)

    Joensuu-Salo, Sanna; Varamäki, Elina; Viljamaa, Anmari

    2015-01-01

    Purpose: Entrepreneurial intentions have been extensively studied in student populations, with results suggesting that higher education does not promote formation of entrepreneurial intentions (e.g. Varamäki et al., 2013). However, the gap between intending to start a business and actually doing something to start one remains. The purpose of this…

  12. Dynamic usage of transcription start sites within core promoters

    DEFF Research Database (Denmark)

    Kawaji, Hideya; Frith, Martin C; Katayama, Shintaro

    2006-01-01

    BACKGROUND: Mammalian promoters do not initiate transcription at single, well defined base pairs, but rather at multiple, alternative start sites spread across a region. We previously characterized the static structures of transcription start site usage within promoters at the base pair level......, based on large-scale sequencing of transcript 5' ends. RESULTS: In the present study we begin to explore the internal dynamics of mammalian promoters, and demonstrate that start site selection within many mouse core promoters varies among tissues. We also show that this dynamic usage of start sites...... is associated with CpG islands, broad and multimodal promoter structures, and imprinting. CONCLUSION: Our results reveal a new level of biologic complexity within promoters--fine-scale regulation of transcription starting events at the base pair level. These events are likely to be related to epigenetic...

  13. University Knowledge Spillovers & Regional Start-up Rates

    DEFF Research Database (Denmark)

    Hellerstedt, Karin; Wennberg, Karl; Frederiksen, Lars

    2014-01-01

    how characteristics of the economic and political milieu within each region influence the ratio of firm births. We find that knowledge spillovers from universities and firm-based R&D strongly affect the start-up rates for both high-tech firms and knowledge-intensive services firms. Further, the start......This chapter investigates how regional start-up rates in the knowledge-intensive services and high-tech industries are influenced by knowledge spillovers from both universities and firm-based R&D activities. Integrating insights from economic geography and organizational ecology into the literature......-up rate of knowledge-intensive service firms is tied more strongly to the supply of university educated individuals and the political regulatory regime within the municipality than start-ups in high-tech industries. This suggests that knowledge-intensive service-start-ups are more susceptible to both...

  14. Starting lithium prophylaxis early v. late in bipolar disorder

    DEFF Research Database (Denmark)

    Kessing, Lars Vedel; Vradi, Eleni; Andersen, Per Kragh

    2014-01-01

    BACKGROUND: No study has investigated when preventive treatment with lithium should be initiated in bipolar disorder. AIMS: To compare response rates among patients with bipolar disorder starting treatment with lithium early v. late. METHOD: Nationwide registers were used to identify all patients...... with a diagnosis of bipolar disorder in psychiatric hospital settings who were prescribed lithium during the period 1995-2012 in Denmark (n = 4714). Lithium responders were defined as patients who, following a stabilisation lithium start-up period of 6 months, continued lithium monotherapy without being admitted...... to hospital. Early v. late intervention was defined in two ways: (a) start of lithium following first contact; and (b) start of lithium following a diagnosis of a single manic/mixed episode. RESULTS: Regardless of the definition used, patients who started lithium early had significantly decreased rates of non...

  15. Managing EHS of PV-Related Equipment at the National Renewable Energy Laboratory: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    McCuskey, T.; Nelson, B. P.

    2012-06-01

    Managing environment, health, and safety (EHS) risks at a national laboratory, or university, can be intimidating to a researcher who is focused on research results. Laboratory research and development (R&D) operations are often driven by scientists with limited engineering support and lack well-refined equipment development resources. To add to the burden for a researcher, there is a plethora of codes, standards, and regulations that govern the safe installation and operation of photovoltaic-related R&D equipment -- especially those involving hazardous production materials. To help guide the researcher through the vast list of requirements, the EHS office at NREL has taken a variety of steps. Organizationally, the office has developed hazard-specific laboratory-level procedures to govern particular activities. These procedures are a distillation of appropriate international codes, fire agencies, SEMI standards, U.S. Department of Energy orders, and other industry standards to those necessary and sufficient to govern the safe operation of a given activity. The EHS office works proactively with researchers after a concept for a new R&D capability is conceived to help guide the safe design, acquisition, installation, and operation of the equipment. It starts with a safety assessment at the early stages such that requirements are implemented to determine the level of risk and degree of complexity presented by the activity so appropriate controls can be put in place to manage the risk. As the equipment requirements and design are refined, appropriate equipment standards are applied. Before the 'to-build' specifications are finalized, a process hazard analysis is performed to ensure that no single-point failure presents an unacceptable risk. Finally, as the tool goes through construction and installation stages, reviews are performed at logical times to ensure that the requisite engineering controls and design are in place and operational. Authorization to

  16. From BookStart to BookSmart : about the importance of an early start with parent-child reading

    NARCIS (Netherlands)

    Berg, Heleen van den

    2015-01-01

    BookStart has been developed to enhance parent-child verbal interactions in early childhood by promoting book sharing. Parents receive a voucher for a baby book and free access to baby books in the library. In a large-scale research, we found that if parents complied with the BookStart suggestion to

  17. Tokamak start-up with electron-cyclotron heating

    Energy Technology Data Exchange (ETDEWEB)

    Holly, D J; Prager, S C; Shepard, D A; Sprott, J C [Wisconsin Univ., Madison (USA)

    1981-11-01

    Experiments are described in which the start-up voltage in a tokamak is reduced by about a factor of two by the use of a modest amount of electron cyclotron resonance heating power for pre-ionization. The solution of the zero-dimensional start-up equations indicates that the effect is due to the high initial density which increases the rate at which the conductivity increases in the neutral-dominated initial plasma. The effect extrapolates favourably to larger tokamaks. A 50% reduction in the start-up volt-second requirement and impurity reflux is also observed.

  18. Improving NPT safeguards. Particularly at the natural uranium starting point

    International Nuclear Information System (INIS)

    Harry, J.; Klerk, P. de

    1996-03-01

    According to the Non Proliferation Treaty (NPT) all nuclear material is subject to safeguards, but according to INFCIRC/153 the full range of safeguards is only applied beyond the 'starting point of safeguards', that is: The point at which nuclear material has reached a composition and purity suitable for fuel fabrication or enrichment. This paper addresses the two questions: (a) is the starting point adequately defined, and (b) what mesures could be applied to nuclear material before the starting point? Those questions have been asked before, some of the answers in this paper are new. (orig.)

  19. Improving NPT safeguards. Particularly at the natural uranium starting point

    Energy Technology Data Exchange (ETDEWEB)

    Harry, J. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Klerk, P. de [Ministry of Foreign Affairs, The Hague (Netherlands)

    1996-03-01

    According to the Non Proliferation Treaty (NPT) all nuclear material is subject to safeguards, but according to INFCIRC/153 the full range of safeguards is only applied beyond the `starting point of safeguards`, that is: The point at which nuclear material has reached a composition and purity suitable for fuel fabrication or enrichment. This paper addresses the two questions: (a) is the starting point adequately defined, and (b) what mesures could be applied to nuclear material before the starting point? Those questions have been asked before, some of the answers in this paper are new. (orig.).

  20. Tokamak start-up with electron-cyclotron heating

    International Nuclear Information System (INIS)

    Holly, D.J.; Prager, S.C.; Shepard, D.A.; Sprott, J.C.

    1981-01-01

    Experiments are described in which the start-up voltage in a tokamak is reduced by about a factor of two by the use of a modest amount of electron cyclotron resonance heating power for pre-ionization. The solution of the zero-dimensional start-up equations indicates that the effect is due to the high initial density which increases the rate at which the conductivity increases in the neutral-dominated initial plasma. The effect extrapolates favourably to larger tokamaks. A 50% reduction in the start-up volt-second requirement and impurity reflux is also observed. (author)

  1. Start-up of NPP Krsko; Pokusno obratovanje NE Krsko

    Energy Technology Data Exchange (ETDEWEB)

    Spiler, J; Aralica, J [Nuklearna elektrana Krsko, Krsko (Yugoslavia)

    1984-07-01

    The report describes a review of start-up program and its realisation. There are also described some more significant start-up results with their evaluation. The most significant operation criteria are compared between NPP Krsko and other similar plants in the world. The comparison shows that after the first contractors and operation personnel efforts have been accomplished, our first nuclear power plant is a safe and reliable source of electric power. At the end there are listed NPP Krsko start-up recommendations and experience. (author)

  2. Biomechanical Analysis of the Swim-Start: A Review

    Directory of Open Access Journals (Sweden)

    Julien Vantorre, Didier Chollet, Ludovic Seifert

    2014-06-01

    Full Text Available This review updates the swim-start state of the art from a biomechanical standpoint. We review the contribution of the swim-start to overall swimming performance, the effects of various swim-start strategies, and skill effects across the range of swim-start strategies identified in the literature. The main objective is to determine the techniques to focus on in swimming training in the contemporary context of the sport. The phases leading to key temporal events of the swim-start, like water entry, require adaptations to the swimmer’s chosen technique over the course of a performance; we thus define the swim-start as the moment when preparation for take-off begins to the moment when the swimming pattern begins. A secondary objective is to determine the role of adaptive variability as it emerges during the swim-start. Variability is contextualized as having a functional role and operating across multiple levels of analysis: inter-subject (expert versus non-expert, inter-trial or intra-subject (through repetitions of the same movement, and inter-preference (preferred versus non-preferred technique. Regarding skill effects, we assume that swim-start expertise is distinct from swim stroke expertise. Highly skilled swim-starts are distinguished in terms of several factors: reaction time from the start signal to the impulse on the block, including the control and regulation of foot force and foot orientation during take-off; appropriate amount of glide time before leg kicking commences; effective transition from leg kicking to break-out of full swimming with arm stroking; overall maximal leg and arm propulsion and minimal water resistance; and minimized energy expenditure through streamlined body position. Swimmers who are less expert at the swim-start spend more time in this phase and would benefit from training designed to reduce: (i the time between reaction to the start signal and impulse on the block, and (ii the time in transition (i

  3. Predicting start-up success with machine learning

    OpenAIRE

    Bento, Francisco Ramadas da Silva Ribeiro

    2018-01-01

    Start-ups are becoming the motor that moves our economy. Google, Apple, or more recently Airbnb and Uber are companies with tremendous impact in worldwide economy, social interactions and government. Over the past decade, both in the US and Europe, there has been an exponential growth in start-up formation. Thus, it seems a relevant challenge understanding what makes this type of high-risk ventures successful and as such, attractive to investors and entrepreneurs. Success for a start-up is de...

  4. Preprint of the Fall 1997 JSAE (Japan Society of Automotive Engineers) Meeting Science Lecture. No. 975; Jidosha gijutsukai 1997 nen shuki taikai gakujutsu koenkai maezurishu. 975

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    No. 975 preprint of the Fall 1997 JSAE was summarized. As for the engine development, papers were made public on a study of reciprocating engine with Z mechanism, the combustion control system, etc. Attention was paid to internal combustion engine-electricity hybrid systems in terms of global warming prevention, and a study was made of environmental improvement effects by introducing next-generation automobiles. Image analysis and computer utilization in the structural design were also described. As to diesel engines, the combustion system and the exhaust gas problem were much studied. Also made were flow analysis on air conditioning and evaluation on the indoor thermal environment. Concerning the manufacturing process and materials, a lot of improvements were made public on thermal fatique resistance, reinforced materials, adoption of ceramics, corrosion resistance/wear resistance, etc. Operability and human engineering, and dynamics and safety are also important themes. Relating to the fuel, low fuel comsumption and additives were studied. The paper reported transmissions and the control systems, torque-transmitting mechanism, frictional property, etc. Especially, research/development were also much made of friction/wear resistant materials. ed and developed

  5. CERN confident of LHC start-up in 2007

    CERN Document Server

    2007-01-01

    "Delegates attending the 140th meeting of CERN Council heard a confident report from the Laboratory about the scheduled start-up of the world's highest energy particle accelerator, the Large Hadron Collier (LHC), in 2007." (1 page)

  6. Short-term treatment outcomes of children starting antiretroviral ...

    African Journals Online (AJOL)

    Short-term treatment outcomes of children starting antiretroviral therapy in the intensive care unit, general medical wards and outpatient HIV clinics at Red Cross War Memorial Children's Hospital, Cape Town, South Africa: A retrospective cohort study.

  7. Method of starting internal pumps of a nuclear reactor

    International Nuclear Information System (INIS)

    Kumagami, Shoji.

    1985-01-01

    Purpose: To reduce the noise effects by decreasing the invading current into the main line upon starting an internal pump type nuclear reactor adapted to forcively recycle the reactor water by a plurality of internal pumps. Method: A plurality of internal pumps are divided into several groups and, upon starting pumps belonging to the individual unit group, the starting instances for the respective pumps are deviated to reduce the surges applied to the main line and suppress the invading current lower to reduce the earth noises. As a result, effects caused to other devices or equipments can be moderated to improve the reliability. Furthermore, by actuating the respective pumps on every group units in a starting pattern along the orthogonal line, flow rate distribution in the reactor can be balanced. Then, the instability region during low rotation of pumps, that is, instability of the flow rate near the resonance frequency can be decreased. (Kawakami, Y.)

  8. School start times and teenage driver motor vehicle crashes.

    Science.gov (United States)

    2015-12-01

    There is substantial evidence that lack of sleep is a significant factor in motor vehicle crashes experienced by teenage drivers. This report examines the hypothesis that a later high school start time may reduce crash rates by reducing the interfere...

  9. Density and starting-energy dependent effective interaction

    International Nuclear Information System (INIS)

    Yamaguchi, Norio; Nagata, Sinobu; Kasuga, Teruo

    1979-01-01

    A new effective potential constructed from the reaction matrix calculation of nuclear matters is proposed, taking three-body effects into account. Starting from the two-body scattering equation for nuclear matters, an equation with averaged momentum is introduced as the definition of effective interaction. The parameters in the equation are the Fermi momentum and the starting energy. The nuclear density dependence and the starting energy dependence are independently treated in the potential. The effective interactions including three-body effects were calculated. The dependence on the starting energy is large. The effective interaction is more attractive in the triplet E state, and assures overall saturation without any artificial renormalization. The reaction matrix calculation can be well reproduced by the calculation with this effective potential. The results of calculation for the binding energy of He-4 and O-16 and the shell model matrix elements of O-16 are represented. (Kato, T.)

  10. 1-D hybrid code for FRM start-up

    International Nuclear Information System (INIS)

    Stark, R.A.; Miley, G.H.

    1982-01-01

    A one-D hybrid has been developed to study the start-up of the FRM via neutral-beam injection. The code uses a multi-group numerical model originally developed by J. Willenberg to describe fusion product dynamics in a solenoidal plasma. Earlier we described such a model for use in determining self-consistent ion currents and magnetic fields in FRM start-up. However, consideration of electron dynamics during start-up indicate that the electron current will oppose the injected ion current and may even foil the attempt to achieve reversal. For this reason, we have combined the multi-group ion (model) with a fluid treatment for electron dynamics to form the hybrid code FROST (Field Reversed One-dimensional STart-up). The details of this merger, along with sample results of operation of FROST, are given

  11. Getting started with digital collections scaling to fit your organization

    CERN Document Server

    Monson, D

    2017-01-01

    This easy-to-follow guide to digitization fundamentals will ensure that readers gain a solid grasp of the knowledge and resources available for getting started on their own digital collection projects.

  12. Dialysis access, infections, and hospitalisations in unplanned dialysis start patients

    DEFF Research Database (Denmark)

    Machowska, Anna; Alscher, Mark Dominik; Vanga, Satyanarayana Reddy

    2017-01-01

    Introduction: Unplanned dialysis start (UPS) associates with worse clinical outcomes, higher utilisation of healthcare resources, lower chances to select dialysis modality and UPS patients typically commenced in-centre haemodialysis (HD) with central venous catheter (CVC). We evaluated patient ou...

  13. CERN confirms goal of 2007 start-up for LHC

    CERN Document Server

    2005-01-01

    Speaking at the 131st session of CERN Council on 17 December 2004, the Director-General, Robert Aymar, confirmed that the top priority is to maintain the goal of starting up the Large Hadron Collider (LHC) in 2007.

  14. MASS TRANSIT: FTA Could Relieve New Starts Program Funding Constraints

    National Research Council Canada - National Science Library

    2001-01-01

    .... Much of this investment has come through the Federal Transit Administration's (FTA) New Starts program, which helps pay for certain rail, bus, and trolley projects through full-funding grant agreements...

  15. Spring 
start-up for the LHC

    CERN Multimedia

    2007-01-01

    A new schedule for the commissioning of the LHC was presented to the Council at its Session in June. The start-up of the accelerator is scheduled for May 2008, to allow all technical problems to be resolved.

  16. Self-starting aerodynamics analysis of vertical axis wind turbine

    OpenAIRE

    Jianyang Zhu; Hailin Huang; Hao Shen

    2015-01-01

    Vertical axis wind turbine is a special type of wind-force electric generator which is capable of working in the complicated wind environment. The self-starting aerodynamics is one of the most important considerations for this kind of turbine. This article aims at providing a systematic synthesis on the self-starting aerodynamic characteristics of vertical axis wind turbine based on the numerical analysis approach. First, the physical model of vertical axis wind turbine and its parameter defi...

  17. An eigenexpansion technique for modelling plasma start-up

    International Nuclear Information System (INIS)

    Pillsbury, R.D.

    1989-01-01

    An algorithm has been developed and implemented in a computer program that allows the estimation of PF coil voltages required to start-up an axisymmetric plasma in a tokamak in the presence of eddy currents in toroidally continuous conducting structures. The algorithm makes use of an eigen-expansion technique to solve the lumped parameter circuit loop voltage equations associated with the PF coils and passive (conducting) structures. An example of start-up for CIT (Compact Ignition Tokamak) is included

  18. University Start-ups: A Better Business Model

    Science.gov (United States)

    Dehn, J.; Webley, P. W.

    2015-12-01

    Many universities look to start-up companies as a way to attract faculty, supporting research and students as traditional federal sources become harder to come by. University affiliated start-up companies can apply for a broader suite of grants, as well as market their services to a broad customer base. Often university administrators see this as a potential panacea, but national statistics show this is not the case. Rarely do universities profit significantly from their start-ups. With a success rates of around 20%, most start-ups end up costing the university money as well as faculty-time. For the faculty, assuming they want to continue in academia, a start-up is often unattractive because it commonly leads out of academia. Running a successful business as well as maintaining a strong teaching and research load is almost impossible to do at the same time. Most business models and business professionals work outside of academia, and the models taught in business schools do not merge well in a university environment. To mitigate this a new business model is proposed where university start-ups are aligned with the academic and research missions of the university. A university start-up must work within the university, directly support research and students, and the work done maintaining the business be recognized as part of the faculty member's university obligations. This requires a complex conflict of interest management plan and for the companies to be non-profit in order to not jeopardize the university's status. This approach may not work well for all universities, but would be ideal for many to conserve resources and ensure a harmonious relationship with their start-ups and faculty.

  19. Strategic Management: Business Model Canvas for Start-Up Company

    OpenAIRE

    Sonninen, Anna

    2016-01-01

    Thesis is written about development of Kakunpala as a Start-Up Company, because development processes and ideas are the key factors for future success of the company. The aim of this thesis is to understand Strategic Management of the Company and Development processes,by using the SWOT analysis before and after development and by applying Business Model Canvas template to the Start-Up Company, and by describing Customer Journey: what relations Kakunpala has with clients and its processes...

  20. Later Start Time for Teens Improves Grades, Mood, and Safety

    Science.gov (United States)

    Wahlstrom, Kyla L.

    2017-01-01

    A recent study by the University of Minnesota looked at eight high schools across the U.S. that chose later start times, from 8:00 a.m. to 8:55 a.m. The study found significant decreases in absences and tardiness as well as greater academic benefits for schools with the latest start times. Among the 9,395 students in the study, those who slept…

  1. Application of STOPP and START criteria: interrater reliability among pharmacists.

    LENUS (Irish Health Repository)

    Ryan, Cristin

    2009-07-01

    Inappropriate prescribing is a well-documented problem in older people. The new screening tools, STOPP (Screening Tool of Older Peoples\\' Prescriptions) and START (Screening Tool to Alert doctors to Right Treatment) have been formulated to identify potentially inappropriate medications (PIMs) and potential errors of omissions (PEOs) in older patients. Consistent, reliable application of STOPP and START is essential for the screening tools to be used effectively by pharmacists.

  2. Dampak Mentoring Pada Keberhasilan Start-Up Business: Studi Kasus Pada Start-Up Business di Indonesia [Mentoring the Impact of Success of a Start-Up Business: A Case Study of a Start-Up Business in Indonesia

    OpenAIRE

    Christina Yanita Setyawati

    2016-01-01

    Entrepreneurship is a highly developed science today, as well as in the world of education in Indonesia. Teaching entrepreneurship at the university level, especially at some universities in Surabaya, the second largest city in Indonesia, shows the positive impact that there were 74.03% of start-up businesses that survived and thrived in 2014. Based on the previous observation, some business start-ups are accompanied by a mentor. Mentoring is a process of forming and maintaining lasting relat...

  3. An Ultra Low Noise Self-Starting Pulse Generator

    DEFF Research Database (Denmark)

    Lasri, J.; Bilenca, A.; Dahan, D.

    2002-01-01

    We describe a self-starting optical pulse source generating 10 GHz, 15 ps pulses with an average jitter of 43 fs and a o.15% amplitude noise over a frequency range of 500 Hz - 1 MHz.......We describe a self-starting optical pulse source generating 10 GHz, 15 ps pulses with an average jitter of 43 fs and a o.15% amplitude noise over a frequency range of 500 Hz - 1 MHz....

  4. Power start up of the Dalat nuclear research reactor

    International Nuclear Information System (INIS)

    Pham Duy Hien; Ngo Quang Huy; Vu Hai Long; Tran Khanh Mai

    1994-01-01

    After accomplishing the physical start-up of the reactor, the power start-up was carried out in February 1984. The power of the reactor has reached: 10 KW on 6/2/1984, 100 KW on 7/2/1984, 200 KW and 300 KW on 8/2/1984; 400 KW and nominal power 500 KW on 9/2/1984. The reactivity temperature coefficient and the xenon poisoning were determined. 3 figs., 12 tabs

  5. Sure start: voices of the 'hard-to-reach'.

    Science.gov (United States)

    Coe, C; Gibson, A; Spencer, N; Stuttaford, M

    2008-07-01

    This research aimed to look in depth at the factors affecting the ability of four Sure Start local programmes, based in a multicultural Midlands city, to engage with 'hard-to-reach' populations. A variety of research strategies and methods were employed. Geographical information systems, participatory research methods and interviews were used in order to understand the extent of the challenge, and hear first hand, why parents may not get involved with Sure Start. The mapping exercise involved collation and mapping of postcode data with respect to boundaries and potential and actual users of Sure Start services. This made possible the identification of any geographical patterning in the distribution of service users and non-users. Participatory research methods were used with parents, enabling them to conduct short interviews within their own communities and make sense of the data collected. Interviews were also conducted with 70 parents across the city, recruited through local schools. The results indicate that parental decisions regarding Sure Start are the product of a complex interaction between numerous factors which may act as either barriers or facilitators to service utilization. The results suggest that a multi-method approach to data collection is useful and appropriate in gaining access to those parents who are non-users of the Sure Start services and enabling their voices to be heard. These findings offer some explanations and insight into the apparent ambivalent attitudes of some families toward Sure Start services. Implications for future practice are discussed.

  6. The backstroke swimming start: state of the art.

    Science.gov (United States)

    de Jesus, Karla; de Jesus, Kelly; Fernandes, Ricardo J; Vilas-Boas, João Paulo; Sanders, Ross

    2014-09-29

    As sprint swimming events can be decided by margins as small as .01 s, thus, an effective start is essential. This study reviews and discusses the 'state of the art' literature regarding backstroke start biomechanics from 23 documents. These included two swimming specific publications, eight peer-reviewed journal articles, three from the Biomechanics and Medicine in Swimming Congress series, eight from the International Society of Biomechanics in Sports Conference Proceedings, one from a Biomechanics Congress and one academic (PhD) thesis. The studies had diverse aims, including swimmers' proficiency levels and data collection settings. There was no single consensus for defining phase descriptions; and kinematics, kinetics and EMG approaches were implemented in laboratory settings. However, researchers face great challenges in improving methods of quantifying valid, reliable and accurate data between laboratory and competition conditions. For example, starting time was defined from the starting signal to distances as disparate as ∼5 m to 22.86 m in several studies. Due to recent rule changes, some of the research outcomes now refer to obsolete backstroke start techniques, and only a few studies considered the actual international rules. This literature review indicated that further research is required, in both laboratory and competition settings focusing on the combined influences of the current rules and block configuration on backstroke starting performances.

  7. Later School Start Times: What Informs Parent Support or Opposition?

    Science.gov (United States)

    Dunietz, Galit Levi; Matos-Moreno, Amilcar; Singer, Dianne C; Davis, Matthew M; O'Brien, Louise M; Chervin, Ronald D

    2017-07-15

    To investigate parental knowledge about adolescent sleep needs, and other beliefs that may inform their support for or objection to later school start times. In 2014, we conducted a cross-sectional, Internet-based survey of a nationally representative sample of parents as part of the C.S. Mott Children's Hospital National Poll on Children's Health. Parents with teens aged 13-17 years reported their children's sleep patterns and school schedules, and whether the parents supported later school start times (8:30 am or later). Responses associated with parental support of later school start times were examined with logistic regression analysis. Overall, 88% of parents reported school start times before 8:30 am, and served as the analysis sample (n = 554). In this group, 51% expressed support for later school start times. Support was associated with current school start times before 7:30 am (odds ratio [OR] = 3.1 [95% confidence interval (CI) 1.2, 8.4]); parental opinion that their teen's current school start time was "too early" (OR = 3.8 [1.8, 7.8]); and agreement with American Academy of Pediatrics recommendations about school start times (OR = 4.7 [2.2, 10.1]). Support also was associated with anticipation of improved school performance (OR = 3.0 [1.5, 5.9]) or increased sleep duration (OR = 4.0 [1.8, 8.9]) with later school start times. Conversely, parents who anticipated too little time for after-school activities (OR = 0.5 [0.3, 0.9]) and need for different transportation plans (OR = 0.5 [0.2, 0.9]) were often less supportive. Parental education about healthy sleep needs and anticipated health benefits may increase their support for later school start times. Educational efforts should also publicize the positive experiences of communities that have made this transition, with regard to limited adverse effect on after-school activity schedules and transportation. © 2017 American Academy of Sleep Medicine

  8. Head Start at Ages 3 and 4 versus Head Start Followed by State Pre-K: Which Is More Effective?

    Science.gov (United States)

    Jenkins, Jade Marcus; Farkas, George; Duncan, Greg J.; Burchinal, Margaret; Vandell, Deborah Lowe

    2016-01-01

    As policy-makers contemplate expanding preschool opportunities for low-income children, one possibility is to fund two, rather than one year of Head Start for children at ages 3 and 4. Another option is to offer one year of Head Start followed by one year of pre-k. We ask which of these options is more effective. We use data from the Oklahoma…

  9. Pre-start timing information is used to set final linear speed in a C-start manoeuvre.

    Science.gov (United States)

    Reinel, Caroline; Schuster, Stefan

    2014-08-15

    In their unique hunting behaviour, archerfish use a complex motor decision to secure their prey: based solely on how dislodged prey initially falls, they select an adapted C-start manoeuvre that turns the fish right towards the point on the water surface where their prey will later land. Furthermore, they take off at a speed that is set so as to arrive in time. We show here that the C-start manoeuvre and not subsequent tail beating is necessary and sufficient for setting this adaptive level of speed. Furthermore, the C-start pattern is adjusted to independently determine both the turning angle and the take-off speed. The selection of both aspects requires no a priori information and is done based on information sampled from the onset of target motion until the C-start is launched. Fin strokes can occur right after the C-start manoeuvre but are not required to fine-tune take-off speed, but rather to maintain it. By probing the way in which the fish set their take-off speed in a wide range of conditions in which distance from the later catching point and time until impact varied widely and unpredictably, we found that the C-start manoeuvre is programmed based on pre-C-start estimates of distance and time until impact. Our study hence provides the first evidence for a C-start that is fine-tuned to produce an adaptive speed level. © 2014. Published by The Company of Biologists Ltd.

  10. TrustRank: a Cold-Start tolerant recommender system

    Science.gov (United States)

    Zou, Haitao; Gong, Zhiguo; Zhang, Nan; Zhao, Wei; Guo, Jingzhi

    2015-02-01

    The explosive growth of the World Wide Web leads to the fast advancing development of e-commerce techniques. Recommender systems, which use personalised information filtering techniques to generate a set of items suitable to a given user, have received considerable attention. User- and item-based algorithms are two popular techniques for the design of recommender systems. These two algorithms are known to have Cold-Start problems, i.e., they are unable to effectively handle Cold-Start users who have an extremely limited number of purchase records. In this paper, we develop TrustRank, a novel recommender system which handles the Cold-Start problem by leveraging the user-trust networks which are commonly available for e-commerce applications. A user-trust network is formed by friendships or trust relationships that users specify among them. While it is straightforward to conjecture that a user-trust network is helpful for improving the accuracy of recommendations, a key challenge for using user-trust network to facilitate Cold-Start users is that these users also tend to have a very limited number of trust relationships. To address this challenge, we propose a pre-processing propagation of the Cold-Start users' trust network. In particular, by applying the personalised PageRank algorithm, we expand the friends of a given user to include others with similar purchase records to his/her original friends. To make this propagation algorithm scalable to a large amount of users, as required by real-world recommender systems, we devise an iterative computation algorithm of the original personalised TrustRank which can incrementally compute trust vectors for Cold-Start users. We conduct extensive experiments to demonstrate the consistently improvement provided by our proposed algorithm over the existing recommender algorithms on the accuracy of recommendations for Cold-Start users.

  11. Dynamic factors and electromyographic activity in a sprint start

    Directory of Open Access Journals (Sweden)

    M Čoh

    2009-07-01

    Full Text Available The aim of the study was to establish the major dynamic parameters as well as the EMG activation of muscles in a sprint start as the first derivative of sprint velocity. The subject of the analysis was block velocity, the production of force in the front and rear starting blocks, the block acceleration in the first two steps and the electromyographic activity (EMG of the following muscles: the erector spinae muscle, gluteus maximus muscle, rectus femoris muscle, vastus medialis muscle, vastus lateralis muscle, biceps femoris muscle and gastrocnemius–medialis muscle. One international-class female sprinter participated in the experiment. She performed eight starts in constant laboratory conditions. The 3-D kinematic analysis was made using a system of nine Smart-e 600 cameras operating at a frame rate of 60 Hz. Dynamic parameters were established by means of two separate force platforms to which the starting blocks were fixed. A 16-channel electromyograph was used to analyse electromyographic activity (EMG. It was established that the block velocity depended on the absolute force produced in the front and rear starting blocks and that it was 2.84±0.21 m.s-1. The maximal force on the rear and front blocks was 628±34 N and 1023±30 N, respectively. In view of the total impulse (210±11 Ns the force production/time ratio in the rear and front blocks was 34%:66%. The erector spinae muscle, vastus lateralis muscle and gastrocnemius–medialis muscle generate the efficiency of the start. The block acceleration in the first two steps primarily depends on the activation of the gluteus maximus muscle, rectus femoris muscle, biceps femoris muscle and gastrocnemius–medialis muscle. A sprint start is a complex motor stereotype requiring a high degree of integration of the processes of central movement regulation and an optimal level of biomotor abilities.

  12. START: An essential step in a new era

    International Nuclear Information System (INIS)

    Lockwood, D.

    1991-01-01

    After more than nine years of negotiations, the US and the Soviet Union signed the Strategic Arms Reduction Treaty (START) in Moscow on July 31, 1991. While the world has changed dramatically since 1982 when the START negotiations began, the treaty remains very much in the US interest. START exacts deep cuts in the most destabilizing and dangerous US and Soviet strategic weapons, and will lead to substantial overall reductions in the strategic nuclear forces of both sides. Moreover, the agreement will create a formal, structured, and predictable strategic environment. It will also impose on the Soviet Union or its successors a legally binding set of obligations that will be in effect for many years, regardless of changes in leadership or form of government. START, with its extensive series of intrusive, cooperative, and technical verification measures, will greatly enhance US knowledge about Soviet strategic nuclear forces and activities. The force reductions, predictability, and transparency that START will lock in will be especially valuable if the Soviet Union breaks into independent states or if there is a resurgence of hard-line political forces in Moscow. In addition, START will provide a framework for deeper reductions that could further reduce the risk of nuclear war, stimulate an increasingly cooperative relationship between the US and the Soviet Union or its successors, and save tens of billions of dollars. Finally, by demonstrating a US and Soviet commitment to reversing the arms race, START should reinforce efforts to stem the proliferation of nuclear weapons among both newly independent Soviet republics and nuclear threshold states, and to ensure success at the Nonproliferation Treaty (NPT) extension conference in 1995

  13. Stop and Restart Effects on Modern Vehicle Starting System Components

    Energy Technology Data Exchange (ETDEWEB)

    Windover, Paul R. [Argonne National Lab. (ANL), Argonne, IL (United States); Owens, Russell J. [Argonne National Lab. (ANL), Argonne, IL (United States); Levinson, Terry M. [Argonne National Lab. (ANL), Argonne, IL (United States); Laughlin, Michael [Argonne National Lab. (ANL), Argonne, IL (United States); Gaines, Linda [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-01-01

    Many drivers of personal and commercial vehicles believe that turning the vehicle off and on frequently instead of idling will cause premature wear of the starter system (starter motor and starter battery). As a result, they are concerned that the replacement cost of the starter motor and/or battery due to increased manual engine cycling would be more than the cumulative cost of the fuel saved by not idling unnecessarily. A number of variables play a role in addressing this complex concern, including the number of starting cycles per day, the time between starting cycles, the intended design life of the starting system, the amount of fuel used to restart an engine, and the cumulative cost of the saved fuel. Qualitative and quantitative information from a variety of sources was used to develop a life-cycle economic model to evaluate the cost and quantify the realistic factors that are related to the permissible frequency of starter motor cycles for the average vehicle to economically minimize engine idle time. Annual cost savings can be calculated depending on shutdown duration and the number of shutdown cycles per day. Analysis shows that cost savings are realized by eliminating idling exceeding one minute by shutting down the engine and restarting it. For a typical motorist, the damage to starting system components resulting from additional daily start cycles will be negligible. Overall, it was found that starter life is mostly dependent on the total number of start cycles, while battery life is more dependent on ensuring a full charge between start events.

  14. School start times and teenage driver motor vehicle crashes.

    Science.gov (United States)

    Foss, Robert D; Smith, Richard L; O'Brien, Natalie P

    2018-04-26

    Shifting school start times to 8:30 am or later has been found to improve academic performance and reduce behavior problems. Limited research suggests this may also reduce adolescent driver motor vehicle crashes. A change in the school start time from 7:30 am to 8:45 am for all public high schools in one North Carolina county presented the opportunity to address this question with greater methodologic rigor. We conducted ARIMA interrupted time-series analyses to examine motor vehicle crash rates of high school age drivers in the intervention county and 3 similar comparison counties with comparable urban-rural population distribution. To focus on crashes most likely to be affected, we limited analysis to crashes involving 16- & 17-year-old drivers occurring on days when school was in session. In the intervention county, there was a 14% downward shift in the time-series following the 75 min delay in school start times (p = .076). There was no change approaching statistical significance in any of the other three counties. Further analysis indicated marked, statistically significant shifts in hourly crash rates in the intervention county, reflecting effects of the change in school start time on young driver exposure. Crashes from 7 to 7:59 am decreased sharply (-25%, p = .008), but increased similarly from 8 to 8:59 am (21%, p = .004). Crashes from 2 to 2:59 pm declined dramatically (-48%, p = .000), then increased to a lesser degree from 3 to 3:59 pm (32%, p = .024) and non-significantly from 4 to 4:59 (19%, p = .102). There was no meaningful change in early morning or nighttime crashes, when drowsiness-induced crashes might have been expected to be most common. The small decrease in crashes among high school age drivers following the shift in school start time is consistent with the findings of other studies of teen driver crashes and school start times. All these studies, including the present one, have limitations, but the similar

  15. A novel induction motor starting method using superconduction

    International Nuclear Information System (INIS)

    Silva, F.B.B.; Orlando, M.T.D.; Fardin, J.F.; Simonetti, D.S.; Baldan, C.A.

    2014-01-01

    Highlights: • Alternative method for starting up induction motor. • Based on using a high-temperature superconductor. • A prototype of the limiter was constructed with a 2G-YBCO tape. • Prototype was tested with a 55-kW industrial induction motor in a 440-V/60-Hz. • Offers reduced current waveform distortion compared to the soft starter method. - Abstract: In this paper, an alternative method for starting up induction motors is proposed, taking into account experimental measurements. The new starting current limitation method is based on using a high-temperature superconductor. A prototype of the superconducting starting current limiter was constructed with a commercially available second-generation high-temperature superconductor YBCO tape, and this was tested with a 55-kW industrial induction motor in a 440-V/60-Hz three-phase power grid. Performance evaluations of the superconducting limiter method (applied to startup of the induction motor) were performed and were compared with a direct-on-line starter and an electronic soft starter. In addition, a computational model was developed and used for electromagnetic torque analysis of the system. As significant characteristics, our method offers the ability to limit the starting current of the induction motor with greater electromagnetic torque, reduced current waveform distortion and therefore lower harmonic pollution during startup when compared to the soft starter method

  16. Self-starting aerodynamics analysis of vertical axis wind turbine

    Directory of Open Access Journals (Sweden)

    Jianyang Zhu

    2015-12-01

    Full Text Available Vertical axis wind turbine is a special type of wind-force electric generator which is capable of working in the complicated wind environment. The self-starting aerodynamics is one of the most important considerations for this kind of turbine. This article aims at providing a systematic synthesis on the self-starting aerodynamic characteristics of vertical axis wind turbine based on the numerical analysis approach. First, the physical model of vertical axis wind turbine and its parameter definitions are presented. Secondary, the interaction model between the vertical axis wind turbine and fluid is developed by using the weak coupling approach; the numerical data of this model are then compared with the wind tunnel experimental data to show its feasibility. Third, the effects of solidity and fixed pitch angle on the self-starting aerodynamic characteristics of the vertical axis wind turbine are analyzed systematically. Finally, the quantification effects of the solidity and fixed pitch angle on the self-starting performance of the turbine can be obtained. The analysis in this study will provide straightforward physical insight into the self-starting aerodynamic characteristics of vertical axis wind turbine.

  17. Control device for start-up of reactor depressurization system

    International Nuclear Information System (INIS)

    Suzuki, Hiroshi; Saito, Minoru; Oda, Shingo; Miura, Satoshi; Hashimoto, Koji; Tate, Hitoshi; Fujii, Kazunobu

    1998-01-01

    The present invention concerns are emergency reactor core cooling system (ECCS) of a BWR type reactor and provides a control device for start-up of an automatic depressurization system. Namely, the device has an object of preventing erroneous opening of a main steam escape safety value when testing a start-up signal circuit of an automatic depressurization system for testing the automatic depressurization system. A start-up signal circuit receives both signals of a reactor container pressure high signal and a reactor pressure vessel water level low signal and outputs an automatic start-up signal for compulsorily opening a main steam escape safety valve automatically. A test switch having a self-holding circuit is disposed to a central control chamber. A test signal circuit is disposed for preventing transfer of an erroneous start-up signal to the main steam escape safety valve due to a simulation signal during output test signals by the test switch. (I.S.)

  18. Start-up Funding via Equity Crowdfunding in Germany

    DEFF Research Database (Denmark)

    Angerer, Martin; Brem, Alexander; Kraus, Sascha

    2017-01-01

    Entrepreneurs often struggle to find sufficient funding for their start-ups. A relatively new way for companies to attract capital is via an internet platform, locating investors who in return receive something in return for their ventures. Equity crowdfunding is one of several types of crowdfund......Entrepreneurs often struggle to find sufficient funding for their start-ups. A relatively new way for companies to attract capital is via an internet platform, locating investors who in return receive something in return for their ventures. Equity crowdfunding is one of several types...... of crowdfunding, and is also known as crowdinvesting in the German-speaking realm. This article predominantly advances the scientific knowledge regarding the success factors of equity crowdfunding for German start-ups. The study conducted nine qualitative interviews with start-ups and crowdinvesting platforms....... Its first result is that German start-ups select crowdinvesting because (1) it is a funding opportunity and (2) it has an expected marketing effect. To organize the results of relevant success factors, the Crowdinvesting Success Model was designed by the researchers. This supports German entrepreneurs...

  19. A novel induction motor starting method using superconduction

    Energy Technology Data Exchange (ETDEWEB)

    Silva, F.B.B., E-mail: flaviobarcelos@ifes.edu.br [Ifes – Federal Institute of Espírito Santo, Dept. of Industrial Automation, Serra, ES 29173087 (Brazil); UFES – Federal University of Espírito Santo, Dept. of Electrical Engineering, Vitória, ES (Brazil); Orlando, M.T.D. [UFES – Federal University of Espírito Santo, Dept. of Physics, Vitória, ES (Brazil); Fardin, J.F.; Simonetti, D.S. [UFES – Federal University of Espírito Santo, Dept. of Electrical Engineering, Vitória, ES (Brazil); Baldan, C.A. [EEL/USP – Engineering School from Lorena/University of São Paulo, SP (Brazil)

    2014-12-15

    Highlights: • Alternative method for starting up induction motor. • Based on using a high-temperature superconductor. • A prototype of the limiter was constructed with a 2G-YBCO tape. • Prototype was tested with a 55-kW industrial induction motor in a 440-V/60-Hz. • Offers reduced current waveform distortion compared to the soft starter method. - Abstract: In this paper, an alternative method for starting up induction motors is proposed, taking into account experimental measurements. The new starting current limitation method is based on using a high-temperature superconductor. A prototype of the superconducting starting current limiter was constructed with a commercially available second-generation high-temperature superconductor YBCO tape, and this was tested with a 55-kW industrial induction motor in a 440-V/60-Hz three-phase power grid. Performance evaluations of the superconducting limiter method (applied to startup of the induction motor) were performed and were compared with a direct-on-line starter and an electronic soft starter. In addition, a computational model was developed and used for electromagnetic torque analysis of the system. As significant characteristics, our method offers the ability to limit the starting current of the induction motor with greater electromagnetic torque, reduced current waveform distortion and therefore lower harmonic pollution during startup when compared to the soft starter method.

  20. The Rationality and Irrationality of Financing Green Start-Ups

    Directory of Open Access Journals (Sweden)

    Linda Bergset

    2015-11-01

    Full Text Available Green start-ups contribute towards a transition to a more sustainable economy by developing sustainable and environmentally friendly innovation and bringing it to the market. Due to specific product/service characteristics, entrepreneurial motivation and company strategies that might differ from that of other start-ups, these companies might struggle even more than usual with access to finance in the early stages. This conceptual paper seeks to explain these challenges through the theoretical lenses of entrepreneurial finance and behavioural finance. While entrepreneurial finance theory contributes to a partial understanding of green start-up finance, behavioural finance is able to solve a remaining explanatory deficit produced by entrepreneurial finance theory. Although some behavioural finance theorists are suggesting that the current understanding of economic rationality underlying behavioural finance research is inadequate, most scholars have not yet challenged these assumptions, which constrict a comprehensive and realistic description of the reality of entrepreneurial finance in green start-ups. The aim of the paper is thus, first, to explore the specifics of entrepreneurial finance in green start-ups and, second, to demonstrate the need for a more up-to-date conception of rationality in behavioural finance theory in order to enable realistic empirical research in this field.

  1. Start-up of spherical tokamak without a center solenoid

    International Nuclear Information System (INIS)

    Maekawa, Takashi; Nagata, Masayoshi

    2012-01-01

    For low-aspect tokamak reactors, spherical tokamak reactors, ST-type FESF/CTFs, it is essential to remove or minimize a central solenoid (CS). Even with the minimized CS, non-inductive start up of the plasma current is required. Rapid increase in the spontaneous plasma current at the final stage of current start-up drives ignition. At the initial stage, formation of plasma and magnetic surfaces are required. As non-inductive plasma start-up scenarios, ECH/ECCD, LHCD, HHFW, DC HELICITY injection, plasma merging and NBI have been studied. In the present article, the present status and future prospect of experimental and theoretical works on these subjects. (author)

  2. Starting characteristics of direct current motors powered by solar cells

    Science.gov (United States)

    Singer, S.; Appelbaum, J.

    1989-01-01

    Direct current motors are used in photovoltaic systems. Important characteristics of electric motors are the starting to rated current and torque ratios. These ratios are dictated by the size of the solar cell array and are different for the various dc motor types. Discussed here is the calculation of the starting to rated current ratio and starting to rated torque ratio of the permanent magnet, and series and shunt excited motors when powered by solar cells for two cases: with and without a maximum-power-point-tracker (MPPT) included in the system. Comparing these two cases, one gets a torque magnification of about 3 for the permanent magnet motor and about 7 for other motor types. The calculation of the torques may assist the PV system designer to determine whether or not to include an MPPT in the system.

  3. Applying behavioral insights to delay school start times.

    Science.gov (United States)

    Kohl Malone, Susan; Ziporyn, Terra; Buttenheim, Alison M

    2017-12-01

    Healthy People 2020 established a national objective to increase the proportion of 9th-to-12th-grade students reporting sufficient sleep. A salient approach for achieving this objective is to delay middle and high school start times. Despite decades of research supporting the benefits of delayed school start times on adolescent sleep, health, and well-being, progress has been slow. Accelerating progress will require new approaches incorporating strategies that influence how school policy decisions are made. In this commentary, we introduce four strategies that influence decision-making processes and demonstrate how they can be applied to efforts aimed at changing school start time policies. Copyright © 2017 National Sleep Foundation. All rights reserved.

  4. Small Vertical Axis Wind Turbines: aerodynamics and starting behavior

    Directory of Open Access Journals (Sweden)

    Horia DUMITRESCU

    2013-12-01

    Full Text Available In urban areas the wind is very turbulent and unstable with fast changes in direction andvelocity. In these environments, the use of small vertical axis wind turbines (VAWT becomesincreasingly attractive due to several advantages over horizontal axis wind turbines (HAWT.However, such designs have received much less attention than the more common propeller-typedesigns and the understanding of same aspects of their operation remains, to this day, incomplete.This is particularly true of their starting characteristics. Indeed, same authors heuristically maintainthat they cannot start without external assistance. This paper reviews the cause of the inability of thelow solidity fixed pitch vertical axis wind turbines to self-start, and investigates the way ofovercoming this draw back.

  5. Starting-up sequence of the AWEC-60 wind turbine

    International Nuclear Information System (INIS)

    Avia, F.; Cruz, M. de la.

    1991-01-01

    One of the most critical status of the wind turbines operation is the starting-up sequence and the connection to the grid, due to the actuating loads that could be several times the loads during operation at rated conditions. Due to this fact, the control strategy is very important during the starting-up sequence in order to minimize the loads on the machine. For this purpose it is necessary to analyze the behaviour of the wind turbine during that sequence in different wind conditions and machine conditions. This report shows the graphic information about fifty starting-up sequences of the AWEC-60 wind turbine of 60 m. diameter and 1200 kW of rated power, recorded in April 1991 and cut-out wind speed. (author)

  6. Start-up processes’ efficiency of turbine jet engines

    Directory of Open Access Journals (Sweden)

    Jankowski Antoni

    2016-12-01

    Full Text Available The paper presents diagnoses of example start-up processes of drive units built in military aircraft operated in the Dęblin's “School of Eaglets” during the flight. The significance of this process is very important, especially from the point of view of flight safety, especially as it concerns the training aircraft, on which officer cadets-candidates for pilots are trained. The diagnosis of the start-up process was conducted using data from on-board flight recorders recorded during a flight training, whose aim was an emergency launch of particular drive units, and with the help of the so-called phase mapping of the selected operating parameters of the particular flight drive systems. The standard diagram of typical start-up systems was shown, while presenting their base subassemblies. At the end, the obtained results and the main problems that need intervention were commented, as well as further preventive activities were proposed.

  7. ECRH-assisted start-up in ITER

    International Nuclear Information System (INIS)

    Lloyd, B.; Carolan, P.G.; Warrick, C.D.

    1996-07-01

    In ITER, the electric field applied for ionisation and to ramp up the plasma current may be limited to ∼ 0.3 V/m. In this case, based on established theories of the avalanche process, it is shown that ohmic breakdown in ITER is only possible over a narrow range of pressure and magnetic error field. Therefore, ECRH may be necessary to provide robust and reliable start-up. ECRH can ensure prompt breakdown over a wide range of prefill pressure and error field and can also give control over the initial time and location of breakdown. For ECRH-assisted start-up in ITER, the power and pulse length requirements are essentially determined by the need to ensure burnthrough, i.e. complete ionisation of hydrogen and the transition to high ionisation states of impurities. A 0-D code (with inclusion of some 1-D effects) has been developed to analyse burnthrough in ITER. The 0-D simulations indicate that control of the deuterium density is the key factor for ensuring successful start-up in ITER, where the effects of neutral screening and dynamic fuelling by the ex-plasma volume are also crucial. It is concluded that without ECRH, successful start-up will only be possible over a very restricted range of parameters but 3MW of absorbed ECRH power will ensure reasonably robust start-up for a broad range of conditions with beryllium impurity. In the case of carbon impurity, even with an absorbed ECRH power of 5MW one may be restricted to low prefill pressure and/or low carbon concentration for successful start-up. (Author)

  8. Sprint Start Kinetics of Amputee and Non-Amputee Sprinters

    Science.gov (United States)

    Willwacher, Steffen; Herrmann, Volker; Heinrich, Kai; Funken, Johannes; Strutzenberger, Gerda; Goldmann, Jan-Peter; Braunstein, Björn; Brazil, Adam; Irwin, Gareth; Potthast, Wolfgang; Brüggemann, Gert-Peter

    2016-01-01

    The purpose of this study was to explore the relationship between the forces applied to the starting blocks and the start performances (SPs) of amputee sprinters (ASs) and non-amputee sprinters (NASs). SPs of 154 male and female NASs (100-m personal records [PRs], 9.58–14.00 s) and 7 male ASs (3 unilateral above knee, 3 unilateral below knee, 1 bilateral below knee; 100 m PRs, 11.70–12.70 s) with running specific prostheses (RSPs) were analysed during full-effort sprint starts using instrumented starting blocks that measured the applied forces in 3D. Using the NAS dataset and a combination of factor analysis and multiple regression techniques, we explored the relationship between force characteristics and SP (quantified by normalized average horizontal block power). Start kinetics were subsequently compared between ASs and NASs who were matched based on their absolute 100 m PR and their 100 m PR relative to the world record in their starting class. In NASs, 86% of the variance in SP was shared with five latent factors on which measured parameters related to force application to the rear and front blocks and the respective push-off directions in the sagittal plane of motion were loaded. Mediolateral force application had little influence on SP. The SP of ASs was significantly reduced compared to that of NASs matched on the basis of relative 100-m PR (−33.8%; d = 2.11, p < 0.001), while a non-significant performance reduction was observed when absolute 100-m PRs were used (−17.7%; d = 0.79, p = 0.09). These results are at least partially explained by the fact that force application to the rear block was clearly impaired in the affected legs of ASs. PMID:27846241

  9. Sprint Start Kinetics of Amputee and Non-Amputee Sprinters.

    Directory of Open Access Journals (Sweden)

    Steffen Willwacher

    Full Text Available The purpose of this study was to explore the relationship between the forces applied to the starting blocks and the start performances (SPs of amputee sprinters (ASs and non-amputee sprinters (NASs. SPs of 154 male and female NASs (100-m personal records [PRs], 9.58-14.00 s and 7 male ASs (3 unilateral above knee, 3 unilateral below knee, 1 bilateral below knee; 100 m PRs, 11.70-12.70 s with running specific prostheses (RSPs were analysed during full-effort sprint starts using instrumented starting blocks that measured the applied forces in 3D. Using the NAS dataset and a combination of factor analysis and multiple regression techniques, we explored the relationship between force characteristics and SP (quantified by normalized average horizontal block power. Start kinetics were subsequently compared between ASs and NASs who were matched based on their absolute 100 m PR and their 100 m PR relative to the world record in their starting class. In NASs, 86% of the variance in SP was shared with five latent factors on which measured parameters related to force application to the rear and front blocks and the respective push-off directions in the sagittal plane of motion were loaded. Mediolateral force application had little influence on SP. The SP of ASs was significantly reduced compared to that of NASs matched on the basis of relative 100-m PR (-33.8%; d = 2.11, p < 0.001, while a non-significant performance reduction was observed when absolute 100-m PRs were used (-17.7%; d = 0.79, p = 0.09. These results are at least partially explained by the fact that force application to the rear block was clearly impaired in the affected legs of ASs.

  10. The start up as a phase of architectural design process.

    Science.gov (United States)

    Castro, Iara Sousa; Lima, Francisco de Paula Antunes; Duarte, Francisco José de Castro Moura

    2012-01-01

    Alterations made in the architectural design can be considered as a continuous process, from its conception to the moment a built environment is already in use. This article focuses on the "moving phase", which is the initial moment of the environment occupation and the start-up of services. It aims to show that the continuity of ergonomics interventions during the "moving phase" or start up may reveal the built environment inadequacies; clearly showing needs not met by the design and allowing making instant decisions to solve non-foreseen problems. The results have revealed some lessons experienced by users during a critical stage not usually included in the design process.

  11. High-inertia drive motors and their starting characteristics

    International Nuclear Information System (INIS)

    Anon.

    1980-01-01

    The motor for a large reactor coolant pump failed while starting. The motor-application and the motor-failure are discussed in detail. A review of applications of motors for high-inertia drives shows that a motor designed and built to today's industry-standards might be overstressed while experiencing abnormal starting conditions, even though its protection is in accord with accepted practice. The inter-relationship between motor characteristics and characteristics of various types of protection are discussed, briefly. The review concludes that motor specifications and motor standards should be augmented. 1 ref

  12. Female Hires and the Success of Start-up Firms

    OpenAIRE

    Weber, Andrea; Zulehner, Christine

    2009-01-01

    In this paper we investigate the relationship between females among the first hires of start-up companies and business success. Our results show that firms with female first hires have a higher share of female workers at the end of the first year after entry. Further, we find that firms with female first hires are more successful and stay longer in the market. We conclude that our results support the hypothesis that gender-diversity in leading positions is an advantage for start-up firms.

  13. Systemic Inflammation, Coagulation, and Clinical Risk in the START Trial

    DEFF Research Database (Denmark)

    Baker, Jason V; Sharma, Shweta; Grund, Birgit

    2017-01-01

    Background: The Strategic Timing of AntiRetroviral Treatment (START) trial demonstrated that immediate (at CD4+ >500 cells/µL) vs deferred (to CD4+ ... available for 4299 START participants (92%). Mean follow-up was 3.2 years. Higher levels of IL-6 and D-dimer were the only biomarkers associated with risk for AIDS, SNA or death, as well as the individual components of SNA and AIDS events (HRs ranged 1.37-1.41 per 2-fold higher level), even after adjustment...

  14. Start-up of plasma current by electron Bernstein wave

    International Nuclear Information System (INIS)

    Maekawa, Takashi; Tanaka, Hitoshi; Uehide, Masaki

    2009-01-01

    Electron cyclotron current drive by electron Bernstein (EB) waves for the start-up and ramp-up of toroidal plasma current with no central solenoid in tokamaks is discussed. It is shown that high N// EB waves have ability to ramp-up the current against the counter voltage from self-induction, where N// is the parallel refractive index to the magnetic field, and they are especially suitable for initial current start-up phase where the bulk electron temperature is low enough to ensure high N// EB waves. (author)

  15. The New START Treaty: Central Limits and Key Provisions

    Science.gov (United States)

    2014-08-27

    article-by-article analysis can be found at http://www.state.gov/t/ avc /newstart/c44126.htm. 2 For a brief summary of the original START Treaty, as...2014, http://www.state.gov/t/ avc /rls/224236.htm . The fact sheet does not display warhead subtotals for each delivery system; it only includes an...of Strategic Offensive Forces, Fact Sheet, Washington, DC, April 1, 2014, http://www.state.gov/t/ avc /rls/228652.htm. The New START Treaty: Central

  16. Start-Up of FEL Oscillator from Shot Noise

    International Nuclear Information System (INIS)

    Kumar, V.; Krishnagopal, S.; Fawley, W.M.

    2007-01-01

    In free-electron laser (FEL) oscillators, as in self-amplified spontaneous emission (SASE) FELs, the buildup of cavity power starts from shot noise resulting from the discreteness of electronic charge. It is important to do the start-up analysis for the build-up of cavity power in order to fix the macropulse width from the electron accelerator such that the system reaches saturation. In this paper, we use the time-dependent simulation code GINGER [1]to perform this analysis. We present results of this analysis for the parameters of the Compact Ultrafast TErahertz FEL (CUTE-FEL) [2] being built at RRCAT

  17. Getting started with SQL Server 2012 cube development

    CERN Document Server

    Lidberg, Simon

    2013-01-01

    As a practical tutorial for Analysis Services, get started with developing cubes. ""Getting Started with SQL Server 2012 Cube Development"" walks you through the basics, working with SSAS to build cubes and get them up and running.Written for SQL Server developers who have not previously worked with Analysis Services. It is assumed that you have experience with relational databases, but no prior knowledge of cube development is required. You need SQL Server 2012 in order to follow along with the exercises in this book.

  18. Program of RA reactor start-up to nominal power

    International Nuclear Information System (INIS)

    1959-01-01

    The zero start-up program is followed by the program of RA reactor start-up to nominal power. This program is described in detail and includes the following measurements: radiation characteristics at the exit of the channels; gamma and fast neutron dose distribution in the reactor; influence of absorbers on the reactivity; temperature effect; absolute flux and calibration of ionization chambers; xenon effect; thermal and hydraulics; dosimetry around the reactor; neutron flux in the reactor core and in the reactor hall; heavy water level; thermal characteristics after shutdown. A list of measuring devices and instrumentation is included with the detailed action plan and list of responsible staff members

  19. Head Start at ages 3 and 4 versus Head Start followed by state pre-k: Which is more effective?

    Science.gov (United States)

    Jenkins, Jade Marcus; Farkas, George; Duncan, Greg J.; Burchinal, Margaret; Vandell, Deborah Lowe

    2016-01-01

    As policy-makers contemplate expanding preschool opportunities for low-income children, one possibility is to fund two, rather than one year of Head Start for children at ages 3 and 4. Another option is to offer one year of Head Start followed by one year of pre-k. We ask which of these options is more effective. We use data from the Oklahoma pre-k study to examine these two ‘pathways’ into kindergarten using regression discontinuity to estimate the effects of each age-4 program, and propensity score weighting to address selection. We find that children attending Head Start at age 3 develop stronger pre-reading skills in a high quality pre-kindergarten at age 4 compared with attending Head Start at age 4. Pre-k and Head Start were not differentially linked to improvements in children’s pre-writing skills or pre-math skills. This suggests that some impacts of early learning programs may be related to the sequencing of learning experiences to more academic programming. PMID:27076692

  20. Start Later, Sleep Later: School Start Times and Adolescent Sleep in Homeschool vs. Public/Private School Students

    Science.gov (United States)

    Meltzer, Lisa J.; Shaheed, Keisha; Ambler, Devon

    2014-01-01

    Homeschool students provide a naturalistic comparison group for later/flexible school start times. This study compared sleep patterns and sleep hygiene for homeschool students and public/private school students (grades 6-12). Public/private school students (n=245) and homeschool students (n=162) completed a survey about sleep patterns and sleep hygiene. Significant school group differences were found for weekday bedtime, wake time, and total sleep time, with homeschool students waking later and obtaining more sleep. Homeschool students had later school start times, waking at the same time that public/private school students were starting school. Public/private school students had poorer sleep hygiene practices, reporting more homework and use of technology in the hour before bed. Regardless of school type, technology in the bedroom was associated with shorter sleep duration. Later school start times may be a potential countermeasure for insufficient sleep in adolescents. Future studies should further examine the relationship between school start times and daytime outcomes, including academic performance, mood, and health. PMID:25315902

  1. Autonomous Energy Grids: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Kroposki, Benjamin D [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Dall-Anese, Emiliano [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bernstein, Andrey [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Zhang, Yingchen [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hodge, Brian S [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-10-04

    With much higher levels of distributed energy resources - variable generation, energy storage, and controllable loads just to mention a few - being deployed into power systems, the data deluge from pervasive metering of energy grids, and the shaping of multi-level ancillary-service markets, current frameworks to monitoring, controlling, and optimizing large-scale energy systems are becoming increasingly inadequate. This position paper outlines the concept of 'Autonomous Energy Grids' (AEGs) - systems that are supported by a scalable, reconfigurable, and self-organizing information and control infrastructure, can be extremely secure and resilient (self-healing), and self-optimize themselves in real-time for economic and reliable performance while systematically integrating energy in all forms. AEGs rely on scalable, self-configuring cellular building blocks that ensure that each 'cell' can self-optimize when isolated from a larger grid as well as partaking in the optimal operation of a larger grid when interconnected. To realize this vision, this paper describes the concepts and key research directions in the broad domains of optimization theory, control theory, big-data analytics, and complex system modeling that will be necessary to realize the AEG vision.

  2. Electrodeless discharge lamp is easily started, has high stability

    Science.gov (United States)

    Bell, W. E.; Bloom, A. L.

    1966-01-01

    Electrodeless discharge borosilicate glass lamp is used in various high-resolution optical systems. It is partially charged with krypton, contains small amounts of rubidium, and is enclosed in a hermetically sealed envelope that maintains the lamp at an optimum temperature during discharge. The lamp is quickly started by its excitation coil.

  3. Lessons Learned about Inclusion While Starting a New College

    Science.gov (United States)

    Jones, Michelle D.

    2018-01-01

    Starting a college from scratch presents a unique opportunity to think about how to build an inclusive learning environment from the beginning by selecting people and strategies that do not carry the weight of the traditional academic model and its prejudices and assumptions about who belongs and who does not. This article documents the lessons…

  4. Steps to Successful Professional Development in Head Start

    Science.gov (United States)

    Trivette, Carol M.; Raab, Melinda; Dunst, Carl J.

    2012-01-01

    This article discusses the implications of utilizing coaching-mentoring strategies with Head Start teachers identified from the results of a study which used an evidence-based approach to professional development. Early childhood and coaching practices that formed the basis of the study are explained. Implications from the study results regarding…

  5. Trends and Tensions: Australian and International Research about Starting School

    Science.gov (United States)

    Dockett, Sue; Perry, Bob

    2013-01-01

    This paper details and compares the discernible trends observed in a wide-ranging review of the recent starting school literature in Australia and beyond. More than half of the research reviewed considers children's readiness for school. This research is critiqued through a three-way view of readiness: child readiness, school readiness and support…

  6. Mass transit : FTA could relieve New Starts program funding constraints

    Science.gov (United States)

    2001-08-01

    The Transportation Equity Act for the 21st Century (TEA-21) authorized $6 billion in "guaranteed" funding for the New Starts program (full funding grant agreements to help pay certain rail, bus, and trolley projects) through fiscal year 2003. The Fed...

  7. Evaluating effectiveness of project start-ups: an exploratory study

    NARCIS (Netherlands)

    Halman, Johannes I.M.; Burger, G.T.N.

    In this paper an exploratory study is reported about the effectiveness of project start-up (PSU) practices within a world-scale operating, high technology innovating and manufacturing company. The emphasis is on the focal position of both project owner and project manager. To uncover potential

  8. Path to Smoking Addiction Starts at Very Young Ages

    Science.gov (United States)

    THE PATH TO TOBACCO ADDICTION STARTS AT VERY YOUNG AGES Lifetime smoking and other tobacco use almost always begins by the time kids graduate from ... regular smoking, which typically turns into a strong addiction—well before the age of 18—that can ...

  9. CERN confident of LHC start-up in 2007

    CERN Document Server

    Vanden Broeck, Renilde

    2007-01-01

    "Delegates attending the 140th meeting of CERN Council today heard a confident report from the Laboratory about the scheduled start-up of the world's highest energy particle accelerator, the Large Hadron Collier (LHC) in 2007. (1/2 page)

  10. CERN confident of LHC start-up in 2007

    CERN Multimedia

    2006-01-01

    "Delegates attending the 140th meeting of CERN Council today heard a confident report from the Laboratory about the scheduled start-up of the world's highest energy particle accelerator, the Large Hadron Collider (LHC) in 2007." (1/2 page)

  11. Cardiovascular and noncardiovascular mortality among patients starting dialysis

    DEFF Research Database (Denmark)

    de Jager, Dinanda J; Grootendorst, Diana C; Jager, Kitty J

    2009-01-01

    CONTEXT: Cardiovascular mortality is considered the main cause of death in patients receiving dialysis and is 10 to 20 times higher in such patients than in the general population. OBJECTIVE: To evaluate if high overall mortality in patients starting dialysis is a consequence of increased cardiov...

  12. Characterization study of industrial waste glass as starting material ...

    African Journals Online (AJOL)

    In present study, an industrial waste glass was characterized and the potential to assess as starting material in development of bioactive materials was investigated. A waste glass collected from the two different glass industry was grounded to fine powder. The samples were characterized using X-ray fluorescence (XRF), ...

  13. Choosing of optimal start approximation for laplace equation ...

    African Journals Online (AJOL)

    We investigate Dirichlet problem for a case of two-dimensional area with lime border, numerical scheme for solving this equation is widely knowns it finite difference method. One of the major stages in the algorithm for that numerical solution is choosing of start approximation, usually as the initial values of the unknown ...

  14. Aan de start: de arbeidsmarktpositie van recent afgestudeerden

    NARCIS (Netherlands)

    Meng, Christoph; Bles, Per; Merens, Ans; Bucx, Freek

    2018-01-01

    Dit hoofdstuk richt zich op de start van de loopbaan. We onderzoeken hoe het jongeren vergaat anderhalf jaar nadat zij hun diploma hebben behaald. De volgende onderzoeksvragen staan centraal: – Hoe is de arbeidsmarktpositie van jongeren anderhalf jaar na hun afstuderen, en welke verschillen zijn er

  15. Head Start Participants, Programs, Families and Staff in 2012

    Science.gov (United States)

    Schmit, Stephanie

    2013-01-01

    Since 1965, the Head Start program has served low-income 3- and 4-year-old children and their families with comprehensive early education and support services. Programs provide services focused on the "whole child," including early education addressing cognitive, developmental, and socio-emotional needs; medical and dental screenings and…

  16. Construction, start-up and operation of a continuously aerated ...

    African Journals Online (AJOL)

    scale SHARON reactor are discussed, along with the construction of the reactor. Special attention is given to the start-up in view of possible toxic effects of high nitrogen concentrations (up to 4 000 mgN·ℓ-1) on the nitrifier population and ...

  17. Head Start Participants, Programs, Families, and Staff in 2014

    Science.gov (United States)

    Mohan, Anitha; Walker, Christina

    2016-01-01

    Since 1965, the Head Start program has served low-income 3- and 4-year-old children and their families with comprehensive early education and support services. Programs provide services focused on the "whole child," including early education addressing cognitive, developmental, and socio-emotional needs; medical and dental screenings and…

  18. Our start-up could never have been successful

    NARCIS (Netherlands)

    Van Kranendonk, J.; De Leeuw, T.; Bonger, S.

    2014-01-01

    In July 2013, TU Delft alumnus Jan van Kranendonk and his business partner Thomas de Leeuw decided to discontinue their start-up company Sunuru. The reason was that customers were not interested in their ingenious solar project. Van Kranendonk spoke about his failure during the Failcon event in

  19. Learnings from an Entrepreneur: How to Start a Consulting Practice

    Science.gov (United States)

    Bowes, Debra

    2013-03-01

    There are important basic learnings I have experienced in starting my own consulting practice over 7 years ago. These learnings will help you maximize your value, reduce competition and build your reputation and business income. I believe these can apply to many fields but certainly for the Life Sciences. A few of the basic I will cover are

  20. Getting started with HTML5 WebSocket programming

    CERN Document Server

    Pterneas, Vangos

    2013-01-01

    Getting Started with HTML5 Websocket Programming takes a tutorial-based approach.This book is for anyone who wants to build high-performance, true, real-time web applications. Being familiar with frontend web development (HTML / XHTML, JavaScript) would be ideal.

  1. Social Capital in Knowledge Intensive Start-Ups

    DEFF Research Database (Denmark)

    Neergaard, Helle; Madsen, Henning

    This paper addresses social capital in biotechnology, medico and information communication start-ups using both quantitative and qualitative data. It shows that founding teams are primarily composed of 'trusted alters' and that networking patterns are highly influenced by the entrepreneur...

  2. Gendered career considerations consolidate from the start of medical education

    NARCIS (Netherlands)

    Alers, M.; Verdonk, P.; Bor, H.; Hamberg, K.; Lagro-Janssen, A.

    2014-01-01

    OBJECTIVE: To explore changes in specialty preferences and work-related topics during the theoretical phase of Dutch medical education and the role of gender. METHODS: A cohort of medical students at Radboudumc, the Netherlands, was surveyed at start (N=612, 69.1% female) and after three years

  3. Delayed Instructional Control of Head Start Children's Free Play.

    Science.gov (United States)

    Pierce, Charles H.; Risley, Todd R.

    The free play of 5 black preschool Head Start children was observed. The variables manipulated in the study were delayed instructions and reinforcement for play with selected toys, and specific versus general instructions; the correspondence between the adult's instructions and reinforcement to the children's play was assessed. The data indicated…

  4. NEW VENTURE CREATION: HOW START-UPS GROW?

    Directory of Open Access Journals (Sweden)

    AIDIN SALAMZADEH

    Full Text Available ABSTRACT Start-ups, often seen as sources of innovation and change, are prone to failure and accordingly they are attracting considerable attention not least from policy makers and Government officials. However, the various new venture creation studies that have emerged since the early 1980s lack cohesiveness, and the domain remains controversial. This article not only exposes the limitations of the existing body of understanding on the topic but attempts to develop a more comprehensive and comprehendible framework for start up (new venture creation. To do so it uses the frameworks proposed by Whetten, and March and Smith to develop 11 propositions. The resultant model suggests that the creation of a start up involves the identification of an idea or opportunity by an entrepreneur who subsequently organizes a series of activities, mobilizes resources and creates competence using his/her networks in an environment in order to create value. It sheds light on the start-up (new venture creation process and has relevance for entrepreneurs, policy makers and researchers.

  5. Stepping Stones: 10 Good Reasons to Start a Blog

    Science.gov (United States)

    Balsley, Jessica

    2012-01-01

    When the author embarked on a journey to start a blog, she had no idea it would save her teaching career. After several years of teaching, she was already burned out. She was caving to the negativity that can often surround education and was just plain tired. She wasn't excited about teaching like she should be. She needed something more. She…

  6. Personality Traits and the Evaluation of Start-up Subsidies

    NARCIS (Netherlands)

    Caliendo, M.; Künn, Steffen; M., Weißenberger,

    2016-01-01

    Many countries support business start-ups to spur economic growth and reduce unemployment with different programmes. Evaluation studies of such programmes commonly rely on the conditional independence assumption (CIA), allowing a causal interpretation of the results only if all relevant variables

  7. Parents' Role in the Early Head Start Children's Language Development

    Science.gov (United States)

    Griswold, Cecelia Smalls

    2014-01-01

    The development of language during a child's early years has been linked to parental involvement. While Early Head Start (EHS) researchers have theorized that parental involvement is an important factor in language development, there has been little research on how parents view their roles in the language development process. The purpose of this…

  8. A Boom Time for Education Start-Ups

    Science.gov (United States)

    DeSantis, Nick

    2012-01-01

    Harsh economic realities mean trouble for college leaders. But where administrators perceive an impending crisis, investors increasingly see opportunity. In recent years, venture capitalists have poured millions into education-technology start-ups, trying to cash in on a market they see as ripe for a digital makeover. And lately, those wagers have…

  9. Multiple problems push LHC start to next spring

    CERN Multimedia

    Guinnessy, Paul

    2007-01-01

    "In June, CERN Director general Robert Aymar announced that the $7 billion Large Hadron Collider would start up in May 2008, eight months later than planned. The delay was no surprise to accelerator and particle physicists, and it was generally blamed on a highly publicized failure related to magnets made at the US's fermilab." (1 page)

  10. Starting SCF Calculations by Superposition of Atomic Densities

    NARCIS (Netherlands)

    van Lenthe, J.H.; Zwaans, R.; van Dam, H.J.J.; Guest, M.F.

    2006-01-01

    We describe the procedure to start an SCF calculation of the general type from a sum of atomic electron densities, as implemented in GAMESS-UK. Although the procedure is well-known for closed-shell calculations and was already suggested when the Direct SCF procedure was proposed, the general

  11. A Mental Health Consultation Program for Project Head Start.

    Science.gov (United States)

    Kawin, Marjorie R.

    The Psychological Center provided a family oriented mental health consultation service to 17 delegate agencies who had contracts with Head Start programs in 1966-67. This paper presents an overview of the services which an interdisciplinary staff of 52 professionals provided to 6,780 families and 1,500 agency staff members. Gerald Caplan's (1964)…

  12. Evaluation of the Start Programme: Case-Study Report

    Science.gov (United States)

    MacLeod, Shona; Sharp, Caroline; Weaving, Harriet; Smith, Robert; Wheater, Rebecca

    2014-01-01

    This report presents five case studies of long-term partnerships (over three years) between arts organisations and schools. The Start programme enables arts venues and schools to work together to offer disadvantaged young people opportunities to engage in creative activities that inspire them and enhance their experience of the arts. It is…

  13. Delayed High School Starting Times. Information Capsule. Volume 0908

    Science.gov (United States)

    Blazer, Christie

    2009-01-01

    Educators around the nation are considering pushing high school starting times back until later in the morning, based on evidence suggesting that amount of sleep and circadian rhythms play a part in adolescents' academic performance. While research confirms that adolescents do not get enough sleep and that insufficient sleep can negatively…

  14. Empowerment Starts Here: Seven Principles to Empowering Urban Youth

    Science.gov (United States)

    Dye, Angela

    2011-01-01

    "Empowerment Starts Here" covers an experimental approach to social change within urban communities by way of seven distinct principles for student empowerment. Turning classroom methods into a school model, Preparatory School for Global Leadership was the first to experience student empowerment at a school-wide level. This book provides insight…

  15. Creating Start-up Companies around NCI Inventions | Poster

    Science.gov (United States)

    By Karen Surabian, Thomas Stackhouse, and Rose Freel, Contributing Writers, and Rosemarie Truman, Guest Writer The National Cancer Institute (NCI), led by the Technology Transfer Center (TTC),  the Avon Foundation, and The Center for Advancing Innovation have partnered to create a “first-of-a-kind” Breast Cancer Start-up Challenge.

  16. Start-Up Rhetoric in Eight Speeches of Barack Obama

    Science.gov (United States)

    O'Connell, Daniel C.; Kowal, Sabine; Sabin, Edward J.; Lamia, John F.; Dannevik, Margaret

    2010-01-01

    Our purpose in the following was to investigate the start-up rhetoric employed by U.S. President Barack Obama in his speeches. The initial 5 min from eight of his speeches from May to September of 2009 were selected for their variety of setting, audience, theme, and purpose. It was generally hypothesized that Barack Obama, widely recognized for…

  17. Dampak Mentoring Pada Keberhasilan Start-Up Business: Studi Kasus Pada Start-Up Business di Indonesia [Mentoring the Impact of Success of a Start-Up Business: A Case Study of a Start-Up Business in Indonesia

    Directory of Open Access Journals (Sweden)

    Christina Yanita Setyawati

    2016-10-01

    Full Text Available Entrepreneurship is a highly developed science today, as well as in the world of education in Indonesia. Teaching entrepreneurship at the university level, especially at some universities in Surabaya, the second largest city in Indonesia, shows the positive impact that there were 74.03% of start-up businesses that survived and thrived in 2014. Based on the previous observation, some business start-ups are accompanied by a mentor. Mentoring is a process of forming and maintaining lasting relationships that develop intensively among seniors with juniors. The mentoring function includes career and psychosocial functions. The main purpose of this research is to study the relationship between mentoring and the success of a start-up business. This study is a quantitative descriptive study using a random sampling method to obtain 100 samples. The tool used to collect data was a questionnaire. The methodology used to analyze the quantitative description to test the hypothesis. The results of this study indicate that mentoring influences the success of a start-up business that was owned by university students in Surabaya, Indonesia by 32% and 78% was influenced by other variables.

  18. Joint kinetic determinants of starting block performance in athletic sprinting.

    Science.gov (United States)

    Brazil, Adam; Exell, Timothy; Wilson, Cassie; Willwacher, Steffen; Bezodis, Ian N; Irwin, Gareth

    2018-07-01

    The aim of this study was to explore the relationships between lower limb joint kinetics, external force production and starting block performance (normalised average horizontal power, NAHP). Seventeen male sprinters (100 m PB, 10.67 ± 0.32 s) performed maximal block starts from instrumented starting blocks (1000 Hz) whilst 3D kinematics (250 Hz) were also recorded during the block phase. Ankle, knee and hip resultant joint moment and power were calculated at the rear and front leg using inverse dynamics. Average horizontal force applied to the front (r = 0.46) and rear (r = 0.44) block explained 86% of the variance in NAHP. At the joint level, many "very likely" to "almost certain" relationships (r = 0.57 to 0.83) were found between joint kinetic data and the magnitude of horizontal force applied to each block although stepwise multiple regression revealed that 55% of the variance in NAHP was accounted for by rear ankle moment, front hip moment and front knee power. The current study provides novel insight into starting block performance and the relationships between lower limb joint kinetic and external kinetic data that can help inform physical and technical training practices for this skill.

  19. Starting Hormone Therapy at Menopause Increases Breast Cancer Risk

    Science.gov (United States)

    According to a January 28, 2011 article in the Journal of the National Cancer Institute, women who start taking menopausal hormone therapy around the time of menopause have a higher risk of breast cancer than women who begin taking hormones a few years later.

  20. One Third More: Maine Head Start Expansion with State Funds.

    Science.gov (United States)

    Weil, Jane

    The expansion of Project Head Start in Maine to the point of serving nearly 25 percent of eligible children is detailed in this report. Section I describes the expansion and some of its benefits, such as equalization of services across county boundaries and the establishment of a uniform unit cost-per-child for use in appropriating state funds.…

  1. The proper name as starting point for basic reading skills

    NARCIS (Netherlands)

    Both-De Vries, Anna C.; Bus, Adriana G

    Does alphabetic-phonetic writing start with the proper name and how does the name affect reading and writing skills? Sixty 4- to 5(1/2)-year-old children from middle SES families with Dutch as their first language wrote their proper name and named letters. For each child we created unique sets of

  2. University–industry collaboration: Jump-starting innovation | IDRC ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2010-10-06

    Oct 6, 2010 ... In Costa Rica, researchers and business have found innovative ways to ... To jump-start these collaborations, IDRC is supporting research teams in 12 ... steel company recently tried to license a type of steel easy to mould into ...

  3. Spousal Capital as a Resource for Couples Starting a Business

    Science.gov (United States)

    Matzek, Amanda E.; Gudmunson, Clinton G.; Danes, Sharon M.

    2010-01-01

    This longitudinal study finds that spousal capital is an important resource for entrepreneurs starting a business because it has implications for business sustainability and couple relationship quality. Structural equation modeling supported a process whereby gender had an impact on spousal involvement in the business, which was positively…

  4. Automated start-up of EBR-II

    International Nuclear Information System (INIS)

    Kisner, R.A.

    1989-01-01

    Oak Ridge National Laboratory (ORNL) and Argonne National Laboratory (ANL) are undertaking a joint project to develop control philosophies, strategies, and algorithms for computer control of the start-up mode of the Experimental Breeder Reactor II (EBR-II). The major objective of this project is to show that advanced liquid-metal reactor (LMR) plants can be operated from low power to full power using computer control. Development of an automated control system with this objective in view will help resolve specific issues and provide proof through demonstration that automatic control for plant start-up is feasible. This paper describes the approach that will be used to develop such a system and some of the features it is expected to have. Structured, rule-based methods, which will provide start-up capability from a variety of initial plant conditions and degrees of equipment operability, will be used for accomplishing mode changes during plant start-up. Several innovative features will be incorporated such as signal, command, and strategy validation to maximize reliability, flexibility to accommodate a wide range of plant conditions, and overall utility. Continuous control design will utilize figures of merit to evaluate how well the controller meets the mission requirements. The operator interface will have unique ''look ahead'' features to let the operator see what will happen next. 15 refs., 7 figs., 1 tab

  5. Online Education: Let's Start the Conversation

    Science.gov (United States)

    Dixon, Robert J.

    2017-01-01

    National shortages of school psychologists have started conversations about training, the number of training programs needed, and how to initiate new programs. This article discusses the difficulties associated with traditional training programs for school psychologists and proposes exploring online education and virtual school psychology service…

  6. Oral desensitization to milk: how to choose the starting dose!

    Science.gov (United States)

    Mori, Francesca; Pucci, Neri; Rossi, Maria Elisabetta; de Martino, Maurizio; Azzari, Chiara; Novembre, Elio

    2010-01-01

    Mori F, Pucci N, Rossi ME, de Martino M, Azzari C, Novembre E. Oral desensitization to milk: how to choose the starting dose! Pediatr Allergy Immunol 2010: 21: e450–e453. © 2009 John Wiley & Sons A/S A renewed interest in oral desensitization as treatment for food allergy has been observed in the last few years. We studied a novel method based on the end point skin prick test procedure to establish the starting dose for oral desensitization in a group of 30 children higly allergic to milk. The results (in terms of reactions to the first dose administered) were compared with a group of 20 children allergic to milk as well. Such control group started to swallow the same dose of 0.015 mg/ml of milk. None reacted to the first dose when administered according to the end point skin prick test. On the other side, ten out of 20 children (50%) from the control group showed mild allergic reactions to the first dose of milk. In conclusion the end point skin prick test procedure results safe and easy to be performed in each single child in order to find out the starting dose for oral desensitization to milk, also by taking into account the individual variability. PMID:19624618

  7. Developing games for health behavior change: Getting started

    Science.gov (United States)

    Many investigators are considering developing video games for health (video-G4Hs) but have questions about how to get started. This report provides guidance for investigators considering a G4H as a behavioral intervention procedure from a team of experienced G4H developers. Thirteen commonly asked q...

  8. Early and Late Language Start at Private Schools in Turkey

    Science.gov (United States)

    Cepik, Saban; Sarandi, Hedayat

    2012-01-01

    This study examines the interaction effect of age in L2 attainment. It explores whether success in foreign language learning at early childhood grades varies depending on age. It also addresses the beliefs of foreign language teachers regarding the variables under review. Eighty-three 11 year-old language learners who started learning English at…

  9. 76 FR 17736 - Major Capital Investment Program-New Starts

    Science.gov (United States)

    2011-03-30

    ... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Major Capital Investment Program--New... unallocated Major Capital Investment (New Starts) program funds. The funds accelerate federal payments for new... projects. The funding will give a well-timed boost to communities that have made important investments in...

  10. Comparative structural analysis of lipid binding START domains.

    Directory of Open Access Journals (Sweden)

    Ann-Gerd Thorsell

    Full Text Available Steroidogenic acute regulatory (StAR protein related lipid transfer (START domains are small globular modules that form a cavity where lipids and lipid hormones bind. These domains can transport ligands to facilitate lipid exchange between biological membranes, and they have been postulated to modulate the activity of other domains of the protein in response to ligand binding. More than a dozen human genes encode START domains, and several of them are implicated in a disease.We report crystal structures of the human STARD1, STARD5, STARD13 and STARD14 lipid transfer domains. These represent four of the six functional classes of START domains.Sequence alignments based on these and previously reported crystal structures define the structural determinants of human START domains, both those related to structural framework and those involved in ligand specificity.This article can also be viewed as an enhanced version in which the text of the article is integrated with interactive 3D representations and animated transitions. Please note that a web plugin is required to access this enhanced functionality. Instructions for the installation and use of the web plugin are available in Text S1.

  11. Start-up of a drinking water biofilter

    DEFF Research Database (Denmark)

    Ramsay, Loren; Søborg, Ditte; Breda, Inês Lousinha Ribeiro

    When virgin filter media is placed in drinking water biofilters, a start-up period of some months typically ensues. During this period, the necessary inorganic coating and bacterial community are established on the filter medium, after which the treated water complies with drinking water criteria...

  12. School start times and teen driver crashes : traffic tech.

    Science.gov (United States)

    2015-12-01

    Sleep health has become an increasingly important and studied : topic in the last decade. So much so that a number of : school districts across the United States have explored changing, : or have already changed their high-school start times to : a l...

  13. Starting from Marginalized Lives: A Conversation with Sandra Harding.

    Science.gov (United States)

    Hirsh, Elizabeth; Olson, Gary A.

    1995-01-01

    Presents a conversation with philosopher of science Sandra Harding, a major exponent of "feminist standpoint theory." Argues that objectivity is maximized not by excluding social factors from the production of knowledge but by starting the process of inquiry from an explicitly social location--the lived experience of those traditionally…

  14. Eleven Tribes Jump START Clean Energy Projects, Summer 2012 (Newsletter)

    Energy Technology Data Exchange (ETDEWEB)

    2012-06-01

    This newsletter describes key activities of the DOE Office of Indian Energy Policy and Programs for Summer 2012. The U.S. Department of Energy Office of Indian Energy Policy and Programs (DOE-IE) has selected 11 Tribes - five in Alaska and six in the contiguous United States - to receive on-the-ground technical support for community-based energy efficiency and renewable energy projects as part of DOE-IE's Strategic Technical Assistance Response Team (START) Program. START finalists were selected based on the clarity of their requests for technical assistance and the ability of START to successfully work with their projects or community. Technical experts from DOE and its National Renewable Energy Laboratory (NREL) will work directly with community-based project teams to analyze local energy issues and assist the Tribes in moving their projects forward. In Alaska, the effort will be bolstered by DOE-IE's partnership with the Denali Commission, which will provide additional assistance and expertise, as well as funding to fuel the Alaska START initiative.

  15. Fast Thorium Molten Salt Reactors Started with Plutonium

    International Nuclear Information System (INIS)

    Merle-Lucotte, E.; Heuer, D.; Le Brun, C.; Brissot, R.; Liatard, E.; Meplan, O.; Nuttin, A.; Mathieu, L.

    2006-01-01

    One of the pending questions concerning Molten Salt Reactors based on the 232 Th/ 233 U fuel cycle is the supply of the fissile matter, and as a consequence the deployment possibilities of a fleet of Molten Salt Reactors, since 233 U does not exist on earth and is not yet produced in the current operating reactors. A solution may consist in producing 233 U in special devices containing Thorium, in Pressurized Water or Fast Neutrons Reactors. Two alternatives to produce 233 U are examined here: directly in standard Molten Salt Reactors started with Plutonium as fissile matter and then operated in the Th/ 233 U cycle; or in dedicated Molten Salt Reactors started and fed with Plutonium as fissile matter and Thorium as fertile matter. The idea is to design a critical reactor able to burn the Plutonium and the minor actinides presently produced in PWRs, and consequently to convert this Plutonium into 233 U. A particular reactor configuration is used, called 'unique channel' configuration in which there is no moderator in the core, leading to a quasi fast neutron spectrum, allowing Plutonium to be used as fissile matter. The conversion capacities of such Molten Salt Reactors are excellent. For Molten Salt Reactors only started with Plutonium, the assets of the Thorium fuel cycle turn out to be quickly recovered and the reactor's characteristics turn out to be equivalent to Molten Salt Reactors operated with 233 U only. Using a combination of Molten Salt Reactors started or operated with Plutonium and of Molten Salt Reactors started with 233 U, the deployment capabilities of these reactors fully satisfy the condition of sustainability. (authors)

  16. Patient perspectives on the optimal start of renal replacement therapy.

    Science.gov (United States)

    Henry, Shayna L; Munoz-Plaza, Corrine; Garcia Delgadillo, Jazmine; Mihara, Nichole K; Rutkowski, Mark P

    2017-09-01

    Healthcare systems and providers are encouraged to prepare their patients with advanced chronic kidney disease (CKD) for a planned start to renal replacement therapies (RRT). Less well understood are the socioemotional experiences surrounding the optimal start of RRT versus suboptimal haemodialysis (HD) starts with a central catheter. To characterise the experiences of patients beginning RRT. Qualitative, semi-structured phone interviews. A total of 168 patients with stage 5 CKD initiating RRT in an integrated, capitated learning healthcare system. Qualitative data from patients were collected as part of a quality improvement initiative to better understand patient-reported themes concerning preparation for RRT, patients' perceptions of their transition to dialysis and why sub-optimal starts for RRT occur within our healthcare system. Dual review and verification was used to identify key phrases and themes within and across each domain, using both deductive a priori codes generated by the interview guide and grounded discovery of emergent themes. From the patient perspective, preparing for RRT is an experience rooted in deep feelings of fear. In addition, a number of key factors contributed to patients' preparation (or failure to prepare) for RRT. While the education provided by our system was viewed as adequate overall, patients often felt that their emotional and psychosocial needs went unmet, regardless of whether or not, they experienced an optimal dialysis start. Future efforts should incorporate additional strategies for helping patients with advanced CKD achieve emotional and psychological safety while preparing for RRT. © 2017 European Dialysis and Transplant Nurses Association/European Renal Care Association.

  17. Start time delays in operating room: Different perspectives

    Directory of Open Access Journals (Sweden)

    Babita Gupta

    2011-01-01

    Full Text Available Background: Healthcare expenditure is a serious concern, with escalating costs failing to meet the expectations of quality care. The treatment capacities are limited in a hospital setting and the operating rooms (ORs. Their optimal utilization is vital in efficient hospital management. Starting late means considerable wait time for staff, patients and waste of resources. We planned an audit to assess different perspectives of the residents in surgical specialities and anesthesia and OR staff nurses so as to know the causative factors of operative delay. This can help develop a practical model to decrease start time delays in operating room (ORs. Aims: An audit to assess different perspectives of the Operating room (OR staff with respect to the varied causative factors of operative delay in the OR. To aid in the development of a practical model to decrease start time delays in ORs and facilitate on-time starts at Jai Prakash Narayan Apex Trauma centre (JPNATC, All India Institute of Medical Sciences (AIIMS, New Delhi. Methods: We prepared a questionnaire seeking the five main reasons of delay as per their perspective. Results: The available data was analysed. Analysis of the data demonstrated the common causative factors in start time operative delays as: a lack of proper planning, deficiencies in team work, communication gap and limited availability of trained supporting staff. Conclusions: The preparation of the equipment and required material for the OR cases must be done well in advance. Utilization of newer technology enables timely booking and scheduling of cases. Improved inter-departmental coordination and compliance with preanesthetic instructions needs to be ensured. It is essential that the anesthesiologists perform their work promptly, well in time . and supervise the proceedings as the OR manager. This audit is a step forward in defining the need of effective OR planning for continuous quality improvement.

  18. Center-Based Child Care in the Pioneer Smart Start Partnerships of North Carolina. UNC Smart Start Evaluation Report.

    Science.gov (United States)

    Maxwell, Kelly; Bryant, Donna; Peisner-Feinberg, Ellen; Buysse, Virginia

    Smart Start is North Carolina's partnership between state government and local leaders, service providers, and families to better serve children under 6 years and their families to ensure that all children enter school healthy and prepared to succeed. This study acquired a baseline measure of the quality of child care in the 12 pioneer Smart Start…

  19. submitter Starting Manufacture of the ITER Central Solenoid

    CERN Document Server

    Libeyre, P; Dolgetta, N; Gaxiola, E; Jong, C; Lyraud, C; Mitchell, N; Journeaux, J Y; Vollmann, T; Evans, D; Sgobba, S; Langeslag, S; Reiersen, W; Martovetsky, N; Everitt, D; Hatfield, D; Rosenblad, P; Litherland, S; Freudenberg, K; Myatt, L; Smith, J; Brazelton, C; Abbott, R; Daubert, J; Rackers, K; Nentwich, T

    2016-01-01

    The central solenoid (CS) is a key component of the ITER magnet system to provide the magnetic flux swing required to drive induced plasma current up to 15 MA. The manufacture of its different subcomponents has now started, following completion of the design analyses and achievement of the qualification of the manufacturing procedures. A comprehensive set of analyses has been produced to demonstrate that the CS final design meets all requirements. This includes in particular structural analyses carried out with different finite-element models and addressing normal and fault conditions. Following the Final Design Review, held in November 2013, and the subsequent design modifications, the analyses were updated for consistency with the final design details and provide evidence that the Magnet Structural Design Criteria are fully met. Before starting any manufacturing activity of a CS component, a corresponding dedicated qualification program has been carried out. This includes manufacture of mockups using the re...

  20. Effects of nutritional supplementation for HIV patients starting antiretroviral treatment

    DEFF Research Database (Denmark)

    Olsen, Mette Frahm; Abdissa, Alemseged; Kæstel, Pernille

    2014-01-01

    Objectives: To determine the effects of lipid based nutritional supplements with either whey or soy protein in patients with HIV during the first three months of antiretroviral treatment (ART) and to explore effects of timing by comparing supplementation at the start of ART and after three months....../µL (−2 to 53 cells/µL) were CD4. Effects of the soy containing supplement on immune recovery were not significant. The effects of the two supplements, however, were not significantly different in direct comparison. Exploratory analysis showed that relatively more lean body mass was gained by patients...... with undetectable viral load at three months. Patients receiving delayed supplementation had higher weight gain but lower gains in functional outcomes. Conclusions: Lipid based nutritional supplements improved gain of weight, lean body mass, and grip strength in patients with HIV starting ART. Supplements...

  1. The role of relationships in start-up development

    DEFF Research Database (Denmark)

    Mattsson, Jan; Helmersson, Helge; Standing, Craig

    2017-01-01

    Relationships are important in the business start-up phase for a variety of reasons. Internal relationships can support knowledge exchange that determines the business model development and external relationships can facilitate a wide range of opportunities, support and insights. The paper explains...... the key relationships experienced by the founding team of a recently formed Swedish digital trading platform. Data were gathered through a self-reporting diary approach based on the Critical Incident Technique format and texts were analysed by the Pertex text-analytic software. The findings explain how...... important relationships were formed during the initial start-up period targeting international expansion. Interaction with early adopters enabled a rapid evolution of the business platform with the aim to build a community of users to support development....

  2. Ten steps to get started in Genome Assembly and Annotation

    Science.gov (United States)

    Dominguez Del Angel, Victoria; Hjerde, Erik; Sterck, Lieven; Capella-Gutierrez, Salvadors; Notredame, Cederic; Vinnere Pettersson, Olga; Amselem, Joelle; Bouri, Laurent; Bocs, Stephanie; Klopp, Christophe; Gibrat, Jean-Francois; Vlasova, Anna; Leskosek, Brane L.; Soler, Lucile; Binzer-Panchal, Mahesh; Lantz, Henrik

    2018-01-01

    As a part of the ELIXIR-EXCELERATE efforts in capacity building, we present here 10 steps to facilitate researchers getting started in genome assembly and genome annotation. The guidelines given are broadly applicable, intended to be stable over time, and cover all aspects from start to finish of a general assembly and annotation project. Intrinsic properties of genomes are discussed, as is the importance of using high quality DNA. Different sequencing technologies and generally applicable workflows for genome assembly are also detailed. We cover structural and functional annotation and encourage readers to also annotate transposable elements, something that is often omitted from annotation workflows. The importance of data management is stressed, and we give advice on where to submit data and how to make your results Findable, Accessible, Interoperable, and Reusable (FAIR). PMID:29568489

  3. Large belt conveyors: starting them and keeping them going

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-03-15

    Although heavy-duty conveyor drives are subjected to some of the most severe operating conditions, it is still possible to achieve reliability and low maintenance. Some areas where choices in design and construction can make a difference include thermal capacity, sealing, lubrication and strength. Dodge recently brought out its redesigned Global Series 750 CST - controlled start transmission - a multi-stage gear reducer with an internal clutch designed for smooth starting of high inertia loads on long-distance conveyors. The Antelope Mine in Wyoming's Powder River Basin first installed Dodge CST units in 1984 and has added more units over the years. CSTs have also been successfully employed in Australian coal mines. 1 fig., 1 photo.

  4. Realizing a desired family size: when should couples start?

    Science.gov (United States)

    Habbema, J Dik F; Eijkemans, Marinus J C; Leridon, Henri; te Velde, Egbert R

    2015-09-01

    Until what age can couples wait to start a family without compromising their chances of realizing the desired number of children? The latest female age at which a couple should start trying to become pregnant strongly depends on the importance attached to achieving a desired family size and on whether or not IVF is an acceptable option in case no natural pregnancy occurs. It is well established that the treatment-independent and treatment-dependent chances of pregnancy decline with female age. However, research on the effect of age has focused on the chance of a first pregnancy and not on realizing more than one child. An established computer simulation model of fertility, updated with recent IVF success rates, was used to simulate a cohort of 10 000 couples in order to assess the chances of realizing a one-, two- or three-child family, for different female ages at which the couple starts trying to conceive. The model uses treatment-independent pregnancy chances and pregnancy chances after IVF/ICSI. In order to focus the discussion, we single out three levels of importance that couples could attach to realizing a desired family size: (i) Very important (equated with aiming for at least a 90% success chance). (ii) Important but not at all costs (equated with a 75% success chance) (iii) Good to have children, but a life without children is also fine (equated with a 50% success chance). In order to have a chance of at least 90% to realize a one-child family, couples should start trying to conceive when the female partner is 35 years of age or younger, in case IVF is an acceptable option. For two children, the latest starting age is 31 years, and for three children 28 years. Without IVF, couples should start no later than age 32 years for a one-child family, at 27 years for a two-child family, and at 23 years for three children. When couples accept 75% or lower chances of family completion, they can start 4-11 years later. The results appeared to be robust for

  5. The Gift of Time? School Starting Age and Mental Health

    DEFF Research Database (Denmark)

    Sievertsen, Hans Henrik; S. Dee, Thomas

    2018-01-01

    influences student outcomes by relying on linked Danish survey and register data that include several distinct, widely used, and validated measures of mental health that are reported out-of-school among similarly aged children. We estimate the causal effects of delayed school enrollment using a "fuzzy.......7), a measure of self regulation with strong negative links to student achievement. We also find that this large and targeted effect persists at age 11. However, the estimated effects of school starting age on other mental-health constructs, which have weaker links to subsequent student achievement, are smaller......In many developed countries, children now begin their formal schooling at an older age. However, a growing body of empirical studies provides little evidence that such schooling delays improve educational and economic outcomes. This study presents new evidence on whether school starting age...

  6. Peer Effects on Head Start Children’s Preschool Competency

    Science.gov (United States)

    DeLay, Dawn; Hanish, Laura D.; Martin, Carol Lynn; Fabes, Richard A.

    2015-01-01

    The goals of the present study were to investigate whether young children attending Head Start (N=292; Mage=4.3 years) selected peers based on their preschool competency and whether children’s levels of preschool competency were influenced by their peers’ levels of preschool competency. Children’s peer interaction partners were intensively observed several times a week over one academic year. Social network analyses revealed that children selected peer interaction partners with similar levels of preschool competency and were influenced over time by their partners’ levels of preschool competency. These effects held even after controlling for several child (e.g., sex and language) and family factors (e.g., financial strain and parent education). Implications for promoting preschool competency among Head Start children are discussed. PMID:26479545

  7. Start up testing for the secure automated fabrication line

    International Nuclear Information System (INIS)

    Gerber, E.W.; Benson, E.M.; Dahl, R.E.

    1986-01-01

    The Secure Automated Fabrication (SAF) Line has been designed and built by Westinghouse Hanford Company for the Department of Energy at the Hanford Site near Richland, Washington. The SAF Line will provide the capability for remote manufacture of fuel for Liquid Metal Reactors, and will supply fuel for the Fast Flux Test Facility (FFTF). The SAF process is highly automated and represents a major advancement in nuclear fuel manufacturing, offering significant improvements in product quality, productivity, safety, and accountability of Special Nuclear Materials. The construction phase of the project is complete, and testing has been initiated to accomplish start up of the plant for manufacture of FFTF fuel. This paper describes the test methodology used for SAF Line start up

  8. Model citizens. Outsourcing helps start-up Medicare HMO.

    Science.gov (United States)

    Slavic, B; Adami, S

    1999-04-01

    Health Plans of Pennsylvania (HPP), the managed care arm of Crozer-Keystone Health System, in Media, Pa. Selecting the information systems and building the infrastructure to support the start-up of a new Medicare HMO product. HPP chose to outsource the information systems needed to integrate all the components of managed care administration into a cost-effective and cohesive program. Because of its aggressive programming and start-up of the MedCarePlus product offering, HPP became the first plan in the country to submit Medicare claims data electronically for encounter reporting to the Health Care Financing Administration (HCFA). "Through an integrated team approach, an organization truly can benefit from the economies of scale gained through outsourcing."

  9. Getting started with Lazarus and Free Pascal learning by doing

    CERN Document Server

    Abiola-Ellison, Menkaura

    2015-01-01

    Whether you want to develop your own database application or develop a web application, or even 2D, 3D, or Animation programs. Getting Started with Lazarus & Free Pascal is quite simply the friendliest, most inspiring Lazarus with Free Pascal programming book available. In this book you will find out how to tackle Object-Oriented Programming using Lazarus with Free Pascal, with confidence. Getting Started with Lazarus & Free Pascal’s simple, step-by-step format makes it a “must-have” book for aspiring programmers. Learn how to master key programming techniques, from simple topics to more advanced topics, following clear instructions with images. For example, find out how to write simple file handling, user-friendly GUI applications, graphics programming, database programming, error trapping, exception handling, debugging techniques, including code documentation and much more. Discover the strength of over 230 Lazarus Component Libraries. This book is packed with inspirational and practical hands...

  10. The Prevessin Control Room during LEP's start up in 1989.

    CERN Multimedia

    1989-01-01

    The Prévessin Control Room saw its first momentous event when the 400 GeV beam for the SPS was commissioned in the presence of Project Leader John Adams. It was also here that the first proton-antiproton collisions were observed, in 1981. Eight years later, in 1989, operators and directors alike jumped for joy at the announcement of the first electron-positron collisions at the start up of LEP, the biggest accelerator in the world.

  11. ECommerce Strategy for Footwear Manufacturing Start-up

    OpenAIRE

    Kuzmanovic, Slobodan

    2010-01-01

    This paper defines and analyzes an eCommerce strategy for a footwear manufacturing start-up firm and assesses the financial impact this eCommerce strategy has in supporting the firm’s business model. The market analysis of the importance of eCommerce determined the online channel’s market share and influence on consumer purchasing decisions, while the industry analysis examined the competitive landscape and industry forces as drivers of forward integration from manufacturing to wholesale and ...

  12. Getting started with Greenplum for big data analytics

    CERN Document Server

    Gollapudi, Sunila

    2013-01-01

    Standard tutorial-based approach.""Getting Started with Greenplum for Big Data"" Analytics is great for data scientists and data analysts with a basic knowledge of Data Warehousing and Business Intelligence platforms who are new to Big Data and who are looking to get a good grounding in how to use the Greenplum Platform. It's assumed that you will have some experience with database design and programming as well as be familiar with analytics tools like R and Weka.

  13. Molecular vibration-rotation spectra starting from the Fues potential

    International Nuclear Information System (INIS)

    Ley Koo, E.

    1976-01-01

    The solution of Schroedinger's equation for the Fues potential is analyzed and compared with the corresponding problems for the Coulomb, harmonic oscillator and molecular potentials. These comparisons allow us to emphasize certain pedagogical, conceptual and computational advantages of the Fues potential which make it a favorable alternative as the starting point in the analysis of molecular vibration-rotation and in the determination of potential energy curves. (author)

  14. A Start-Up Produces Infomercials for the Internet

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    @@ The one thing online shopping is missing, says Sukhinder Singh Cassidy, a former Google executive, is infomercials. Ms.Singh Cassidy introduced her new shopping start-up, Joyus.It is an e-commerce site that produces videos to sell products, like a Web version of the Home Shopping Network. "If you think about the ways to sell online, video is underutilized," she said."It's a new way for brands to merchandise their product."

  15. 3.5 TeV : a good start!

    CERN Multimedia

    2009-01-01

    To the pessimists out there, the 3.5 TeV starting energy of the LHC will be like a half-empty glass. However, the thousands of physicists working at the experiments certainly do not share these feelings. On the contrary, they are as excited as ever since they will be the first to observe what happens to matter in these (still) unprecedented conditions.

  16. How to start a home-based blogging business

    CERN Document Server

    Snyder, Brett

    2012-01-01

    Having passion about a topic is a great reason to start blogging, but there is a lot more to it than that. This book will be able to help potential bloggers by asking the important questions needed to focus the blog. It will also set expectations so there are fewer surprises along the way. Making a blog a success can be a challenge, but it's not out of reach for those who are determined.

  17. Digital Marketing practices amongst start-up accelerators

    OpenAIRE

    Azinheiro, Marisa Filipa Ramos

    2017-01-01

    Digital Marketing (DM) is a vital marketing tool used by all types of companies nowadays. Accelerators are companies that appeared in the last few years to help start-ups grow and, just like any other company, they are using DM as well. This research explored which were the DM strategies used by accelerators. To do so, an online survey was shared amongst more than 300 accelerators across the world, whose results were analyzed by using SPSS Software. Correlation analyses and significance te...

  18. SOME SYSTEMATIC SAMPLING STRATEGIES USING MULTIPLE RANDOM STARTS

    OpenAIRE

    Sampath Sundaram; Ammani Sivaraman

    2010-01-01

    In this paper an attempt is made to extend linear systematic sampling using multiple random starts due to Gautschi(1957)for various types of systematic sampling schemes available in literature, namely(i)  Balanced Systematic Sampling (BSS) of  Sethi (1965) and (ii) Modified Systematic Sampling (MSS) of Singh, Jindal, and Garg  (1968). Further, the proposed methods were compared with Yates corrected estimator developed with reference to Gautschi’s Linear systematic samplin...

  19. Business start-ups and the effect of coaching programs

    OpenAIRE

    Loersch, Christian

    2015-01-01

    Entrepreneurship is known to be a main driver of economic growth. Hence, governments have an interest in supporting and promoting entrepreneurial activities. Start-up subsidies, which have been analyzed extensively, only aim at mitigating the lack of financial capital. However, some entrepreneurs also lack in human, social, and managerial capital. One way to address these shortcomings is by subsidizing coaching programs for entrepreneurs. However, theoretical and empirical evidence about busi...

  20. HF-START: A Regional Radio Propagation Simulator

    Science.gov (United States)

    Hozumi, K.; Maruyama, T.; Saito, S.; Nakata, H.; Rougerie, S.; Yokoyama, T.; Jin, H.; Tsugawa, T.; Ishii, M.

    2017-12-01

    HF-START (HF Simulator Targeting for All-users' Regional Telecommunications) is a user-friendly simulator developed to meet the needs of space weather users. Prediction of communications failure due to space weather disturbances is of high priority. Space weather users from various backgrounds with high economic impact, i.e. airlines, telecommunication companies, GPS-related companies, insurance companies, international amateur radio union, etc., recently increase. Space weather information provided by Space Weather Information Center of NICT is, however, too professional to be understood and effectively used by the users. To overcome this issue, I try to translate the research level data to the user level data based on users' needs and provide an immediate usable data. HF-START is positioned to be a space weather product out of laboratory based truly on users' needs. It is originally for radio waves in HF band (3-30 MHz) but higher frequencies up to L band are planned to be covered. Regional ionospheric data in Japan and southeast Asia are employed as a reflector of skywave mode propagation. GAIA (Ground-to-topside model of Atmosphere and Ionosphere for Aeronomy) model will be used as ionospheric input for global simulation. To evaluate HF-START, an evaluation campaign for Japan region will be launched in coming months. If the campaign successes, it will be expanded to southeast Asia region as well. The final goal of HF-START is to provide the near-realtime necessary radio parameters as well as the warning message of radio communications failure to the radio and space weather users.

  1. Relationships between school start time, sleep duration, and adolescent behaviors.

    Science.gov (United States)

    Wahlstrom, Kyla L; Berger, Aaron T; Widome, Rachel

    2017-06-01

    The objectives were 2-fold: (1) to examine how high school start times relate to adolescent sleep duration, and (2) to test associations between sleep duration and mental health- and substance use-related issues and behaviors in teens. This study examines selected questions from survey data collected between 2010 and 2013 high school students. Respondents included more than 9000 students in grades 9 to 12 in 8 high schools in 5 school districts across the United States. The survey instrument is the 97-item Teen Sleep Habits Survey. Logistic regression models were used to calculate adjusted odds ratios and 95% confidence intervals. Because of clustering within schools and the use of repeated measures, generalized estimating equations were used to account for variance inflation. Greater sleep duration was associated with fewer reports of various mental health- and substance use-related issues and behaviors (all P values sleep reported, there was a 28% reduction in the adjusted odds of a participant reporting that he or she felt "unhappy, sad, or depressed." Later wake-up times were associated with a reduction in risk for some, but not all factors. Later start times were significantly associated with greater sleep duration. Given that later start times allow for greater sleep duration and that adequate sleep duration is associated with more favorable mental health- and substance use-related issues and behaviors, it is important that school districts prioritize exploring and implementing policies, such as delayed start times, that may increase the amount of sleep of adolescent students, which is needed for their optimal development. Copyright © 2017 National Sleep Foundation. Published by Elsevier Inc. All rights reserved.

  2. Opportunity identification and evaluation in franchisee business start-ups

    OpenAIRE

    Brookes, Maureen; Altinay, Levent; Wang, Xuan Lorna; Yeung, Ruth

    2016-01-01

    Purpose - This paper examines franchisees’ business start-ups from an entrepreneurial perspective, adopting a process representative of entrepreneurship to examine opportunity identification and evaluation by franchisees and to analyse factors that influence this process.\\ud \\ud Design/methodology/approach - A qualitative study was employed and data collected using semi-structured interviews with a sample of service industry franchisees in Macau.\\ud \\ud Findings - The study identifies that so...

  3. Laser-start-up system for magnetic mirror fusion

    International Nuclear Information System (INIS)

    Frank, A.M.; Thomas, S.R.; Denhoy, B.S.; Chargin, A.K.

    1976-01-01

    A CO 2 laser system has been developed at LLL to provide hot start-up plasmas for magnetic mirror fusion experiments. A frozen ammonia pellet is irradiated with a laser power density in excess of 10 13 W/cm 2 in a 50-ns pulse. This system uses commercially available laser systems. Optical components were fabricated both by direct machining and standard techniques. The technologies used in this system are directly applicable to reactor scale systems

  4. Getting started with OpenCart module development

    CERN Document Server

    Nepali, Rupak

    2013-01-01

    Written as a step-by-step guide, Getting Started with OpenCart Module Development will teach you all you need to know about OpenCart, from custom extensions to module development.This book is for developers who want to develop OpenCart extensions and for those who want to learn more about the code workflow of OpenCart. Basic knowledge of OpenCart would be an added advantage.

  5. Bootstrap finance: the art of start-ups.

    Science.gov (United States)

    Bhide, A

    1992-01-01

    Entrepreneurship is more popular than ever: courses are full, policymakers emphasize new ventures, managers yearn to go off on their own. Would-be founders often misplace their energies, however. Believing in a "big money" model of entrepreneurship, they spend a lot of time trying to attract investors instead of using wits and hustle to get their ideas off the ground. A study of 100 of the 1989 Inc. "500" list of fastest growing U.S. start-ups attests to the value of bootstrapping. In fact, what it takes to start a business often conflicts with what venture capitalists require. Investors prefer solid plans, well-defined markets, and track records. Entrepreneurs are heavy on energy and enthusiasm but may be short on credentials. They thrive in rapidly changing environments where uncertain prospects may scare off established companies. Rolling with the punches is often more important than formal plans. Striving to adhere to investors' criteria can diminish the flexibility--the try-it, fix-it approach--an entrepreneur needs to make a new venture work. Seven principles are basic for successful start-ups: get operational fast; look for quick break-even, cash-generating projects; offer high-value products or services that can sustain direct personal selling; don't try to hire the crack team; keep growth in check; focus on cash; and cultivate banks early. Growth and change are the start-up's natural environment. But change is also the reward for success: just as ventures grow, their founders usually have to take a fresh look at everything again: roles, organization, even the very policies that got the business up and running.

  6. FUMEX-III Cases by START-3. Final Report

    International Nuclear Information System (INIS)

    Novikov, Vladimir; Bogatyr, Sergey; Kuznetsov, Vladimir; Chulkin, Dmitriy

    2013-01-01

    This document covers ''SUPER-RAMP'' and ''AREVA High-Burnup Idealised case'', cases of FUMEX-III project that were calculated by means of START-3 code. SUPER-RAMP PK-2 rodlets were chosen for calculation because they were subjected to strong power ramp and did not fail, because the main objective of the present calculations was to check the models of fission gas release and gaseous swelling of START-3 in the conditions of the power ramps (we did not intend to get the limit stresses for Zry-4 fuel rods). AREVA high burnup (PRIORITY CASE) case was chosen to check the applicability of the START-3 code to high-burnup PWR fuel rods behavior. Also, in order to check the stability and quality of the changes made into the code during the course of FUMEX-III participation, several simplified cases of FUMEX-II were recalculated. FUMEX-III SUPER-RAMP exercise included up to 49 kW/m power ramps of fuel rods with burnup up to 45 MWd/kgU. START-3 calculations of this exercise are in reasonable agreement with the experiment. AREVA high burnup priority case (∼81.5 MWd/kgU) was calculated and overprediction of the FGR was found. This overprediction is related with the conservative overestimation of rim-structure capability to retain fission gas and can be adjusted implementing a simple correction of this property. To verify the changes made into the code (oxide layer growth model and Zry-4 radiation growth), the corrected version of the code was used to recalculate the FUMEX-II simplified cases 27.2 and satisfactory results were obtained. (author)

  7. Deep geological repository: Starting communication at potentially suitable sites

    International Nuclear Information System (INIS)

    Sumberova, Vera

    2001-01-01

    The siting of a deep geological repository in the Czech Republic is and will be a complicated process, since it is the first siting process of a nuclear facility designed from the start to be located at non-nuclear sites and to be organised under democratic conditions. This presentation describes the concept of radioactive waste and spent nuclear management in the Czech Republic, Communication activities of Radioactive Waste Repository Authority (RAWRA) with local representatives and lessons learned

  8. Anticipated simulation of Angra-1 start-up physical tests

    International Nuclear Information System (INIS)

    Fernandes, V.B.; Perrotta, J.A.; Silva Ipojuca, T. da; Ponzoni Filho, P.

    1981-01-01

    Some results foreseen by the Department of Nuclear Fuel (DCN. O) in Furnas for the measurements that will be realized during the start-up integrated tests for Angra-1 are presented. All the forecasting is based on a DCN.O proper correlation methodology, developed from basic physical principles, using computer codes developed by the authors or public computer codes adapted to this methodology. (E.G.) [pt

  9. From the Ground Up: Starting a Theological Library from Scratch

    Directory of Open Access Journals (Sweden)

    Gerald Truman

    2010-06-01

    Full Text Available There is no “How To” manual for starting an academic library. This essay is one experience in the effort to take a room of books and make the journey to an accredited resource center for a theological graduate school. The collaborative expertise of colleagues, the wisdom and direction garnered from professional meetings, and the wary wiles of technological information resources serves to chronicle this rocky and rewarding road to accomplishment

  10. Flow Behavior Around a Fast-Starting Robotic Fish

    Science.gov (United States)

    Ma, Ganzhong; Currier, Todd; Modarres-Sadeghi, Yahya

    2017-11-01

    A robotic fish is used to study the flow behavior around the body of a fast-starting fish as it experiences a fast-start. The robotic fish is designed and built emulating a Northern Pike, Esox Lucius, which can accelerate at up to 245 m/s2. In previous studies, we had focused on the flow around the tail during the fast-start, by using a tail which acted flexibly in the preparatory stage and rigidly in the propulsive stage. We have extended that study by including the fish body in the experimental setup, where the body can bend into a C-shape, so that the influence of the body motion on the resulting flow around the structure can be understood as well. In the tests, the fish can rotate about a vertical axis, where a multi-axis force sensor measures flow forces acting on the body. Synchronized with the force measurement, flow visualizations using bubble image velocimetry are conducted, and the observed shed vortices are related to the peak forces observed during the maneuver.

  11. The hundredth Gentner Doctoral Student has started at CERN

    CERN Multimedia

    CERN Bulletin

    2016-01-01

    Almost ten years after the start of the programme in 2007, the hundredth Gentner Doctoral Student started his PhD at CERN.   The hundredth Gentner Doctoral Student, Christian Zimmer, in front of the AEgIS detector in the AD hall, where he will spend a significant portion of the next 3 years. In 2007, the German Gentner Doctoral Student Programme was established at CERN, named in honour of the celebrated nuclear physicist Wolfgang Gentner, President of the CERN Council from 1972-74. On 1 July 2016, the 100th Gentner Doctoral Student, Christian Zimmer, started his PhD at CERN, where he will work on setting up the sympathetic laser cooling of antiprotons at the AEgIS experiment. CERN’s Doctoral Student Programme has been running for many years, with 200 students currently enrolled. The Gentner programme is fully integrated into the general CERN Doctoral Student Programme, but is entirely funded by the German Federal Ministry of Education and Research (BMBF). The programme sponsors 30 to 40...

  12. The New START Treaty: a necessary or obsolete treaty?

    International Nuclear Information System (INIS)

    Ekovich, Steven

    2012-01-01

    In a first part, the author evokes the discussions between the Republicans and the Democrats about the fact that President Obama said to President Medvedev he would have more flexibility to negotiate with Russia after the elections of 2012, whereas there is some controversy about the importance of US antimissile defence in terms of national security when Russia keeps on supporting dangerous states like Syria, North Korea and Iran. In a second part, he briefly recalls the objectives and content of the previous START treaties, outlines that START II is already obsolete, that which lead to a new approach called New START by the White House. Then, while noticing critics and evoking other treaties, he discusses the arguments for or against such a new treaty which is perceived as either only cosmetic or decisive. He comments ambiguities, ulterior motives, perceptions and strategic approaches of the different actors whether they are Russians or Americans. He finally outlines some measures of this New Treaty which may jeopardize positive expectations regarding the reduction of strategic weapons and the antimissile defence

  13. Reactor water quality degradation suppressing method upon reactor start up

    International Nuclear Information System (INIS)

    Maeda, Katsuharu.

    1993-01-01

    Preceding to reactor start-up, vacuum degree in a condenser is increased, and after the vacuum degree has been increased sufficiently, a desalting tower is inserted. Then, water feed to the reactor is started and the reactor is operated so that water is supplied gradually. Thus, dissolved oxygen in the feedwater and condensates is kept low and an entire organic carbon leaching rate from resins in the condensate desalting tower is reduced. Further, since feedwater is gradually supplied after the start-up, the entire organic carbon brought into the reactor is decomposed by heat and radiation and efficiently removed by a reactor coolant cleanup system. As a result, corrosion of stainless steel or the like is suppressed, as well as integrity of fuels can be maintained. Further, degradation of water quality can be suppressed effectively not by additionally putting the condensate desalting towers to in-service in accordance with the increase of the feedwater flow rate accompanying the power up but by previously putting the condensate desalting towers to in-service. (N.H.)

  14. Agile methodology selection criteria: IT start-up case study

    Science.gov (United States)

    Micic, Lj

    2017-05-01

    Project management in modern IT companies is often based on agile methodologies which have several advantages compared to traditional methodologies such is waterfall. Having in mind that clients sometimes change project during development it is crucial for an IT company to choose carefully which methodology is going to implement and is it going to be mostly based on one or is it going got be combination of several. There are several modern and often used methodologies but among those Scrum, Kanban and XP programming are usually the most common. Sometimes companies use mostly tools and procedures from one but quite often they use some of the combination of those methodologies. Having in mind that those methodologies are just a framework they allow companies to adapt it for their specific projects as well as for other limitations. These methodologies are in limited usage Bosnia but more and more IT companies are starting to use agile methodologies because it is practice and common not just for their clients abroad but also starting to be the only option in order to deliver quality product on time. However it is always challenging which methodology or combination of several companies should implement and how to connect it to its own project, organizational framework and HR management. This paper presents one case study based on local IT start up and delivers solution based on theoretical framework and practical limitations that case company has.

  15. Long Pulse EBW Start-up Experiments in MAST

    Directory of Open Access Journals (Sweden)

    Shevchenko V.F.

    2015-01-01

    Full Text Available Start-up technique reported here relies on a double mode conversion (MC for electron Bernstein wave (EBW excitation. It consists of MC of the ordinary (O mode, entering the plasma from the low field side of the tokamak, into the extraordinary (X mode at a mirror-polarizer located at the high field side. The X mode propagates back to the plasma, passes through electron cyclotron resonance (ECR and experiences a subsequent X to EBW MC near the upper hybrid resonance (UHR. Finally the excited EBW mode is totally absorbed at the Doppler shifted ECR. The absorption of EBW remains high even in cold rarefied plasmas. Furthermore, EBW can generate significant plasma current giving the prospect of a fully solenoid-free plasma start-up. First experiments using this scheme were carried out on MAST [1]. Plasma currents up to 33 kA have been achieved using 28 GHz 100kW 90ms RF pulses. Recently experimental results were extended to longer RF pulses showing further increase of plasma currents generated by RF power alone. A record current of 73kA has been achieved with 450ms RF pulse of similar power. The current drive enhancement was mainly achieved due to RF pulse extension and further optimisation of the start-up scenario.

  16. [Starting with camphor--the progress of Nippon Fine Chemical].

    Science.gov (United States)

    Kimura, Osamu

    2010-01-01

    In 1918, Nippon Fine Chemical Co., Ltd. (NFC) was founded under the name, Nippon Camphor Co., Ltd. for the purpose of unifying the camphor business throughout Japan. The company manufactured purified camphor as a government-monopolized good. Camphor was used as a plasticizer for nitrocellulose, as a moth repellent, as an antimicrobial substance, as a rust inhibitor, and as an active ingredient in medicine. It was also a very important good exported in order to obtain foreign currency. Later on, after World War II and the abolition of the camphor monopoly, the company started manufacturing products related to oils and fats, including higher fatty acids, and expanded its business by developing a new field of chemical industry. In 1971 the company changed its name to Nippon Fine Chemical Co., Ltd., and made a new start as a diversified fine chemicals company. Recently, the fine chemicals division of NFC has concentrated on rather complex molecules, such as active pharmaceutical ingredients, and other chemicals. Since 2000, NFC have started to supply "Presome", precursors of liposome DDS drugs. NFC is strengthening marketing strategies in foreign countries with unique technologies and products.

  17. Shippingport Station Decommissioning Project Start of Physical Decommissioning

    International Nuclear Information System (INIS)

    Crimi, F. P.

    1987-01-01

    The Shippingport Atomic Power Station consists of the nuclear steam supply system and associated radioactive waste processing systems, which are owned by the United States Department of Energy, and the turbine-generator and balance of plant, which is owned by the Duquesne Light Company. The station is located at Shippingport, Pennsylvania on seven acres of land leased by DOE from Duquesne Light Company. The Shippingport Station Decommissioning Project is being performed under contract to the DOE by the General Electric Company and its integrated subcontractor, Morrison-Knudsen Company. as the Decommissioning Operations Contractor. This paper describes the current status of the physical decommissioning work, which started September 1985. The preparations required to start a major decommissioning work effort in a safe and cost effective manner are discussed including the development and implementation of a cost/schedule control system. The detailed plan required to ensure that people, property, and procedures are ready in sufficient time to support the start of physical decommissioning is also discussed. The total estimated cost of the Shippingport Station Decommissioning Project should be $98.3 M, with the Project scheduled for completion in April 1990. As the decommissioning of the first commercial-scale nuclear power plant, the Shippingport Project is expected to set the standard for safe, cost-effective demolition of nuclear plants

  18. Effects of secondary prophylaxis started in adolescent and adult haemophiliacs.

    Science.gov (United States)

    Tagliaferri, A; Franchini, M; Coppola, A; Rivolta, G F; Santoro, C; Rossetti, G; Feola, G; Zanon, E; Dragani, A; Iannaccaro, P; Radossi, P; Mannucci, P M

    2008-09-01

    While primary prophylaxis is a well-established and recommended method of care delivery for children with severe haemophilia, fewer studies have documented the benefits of secondary prophylaxis started in adolescence or adulthood. To evaluate the role of secondary prophylaxis started in adolescent and adult severe haemophiliacs, a retrospective observational cohort study was conducted in 10 Italian Centres that investigated 84 haemophiliacs who had bled frequently and had thus switched from on-demand to prophylactic treatment during adolescence (n = 30) or adulthood (n = 54). The consumption of clotting factor concentrates, the orthopaedic and radiological scores, quality of life and disease-related morbidity were compared before and after starting secondary prophylaxis. Prophylaxis reduced the mean annual number of total and joint bleeds (35.8 vs. 4.2 and 32.4 vs. 3.3; P work/school (34.6 vs. 3.0, P life. With respect to on-demand treatment, higher factor consumption and cost of secondary prophylaxis were balanced by marked clinical benefits and greater well-being in this cohort of adolescent/adult haemophiliacs.

  19. Fusion reactor start-up without an external tritium source

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, S., E-mail: Shanliang.Zheng@ccfe.ac.uk; King, D.B.; Garzotti, L.; Surrey, E.; Todd, T.N.

    2016-02-15

    Highlights: • Investigated the feasibility (including plasma physics, neutronics and economics) of starting a fusion reactor from running pure D–D fusion reactor to gradually move towards the D–T operation. • Proposed building up tritium from making use of neutrons generated by D–D fusion reactions. • Studied plasma physics feasibility for pure D–D operation and provided consistent fusion power and neutron yield in the plasma with different mixture of deuterium and tritium. • Discussed the economics aspect for operating a pure D–D fusion reactor towards a full-power D–T fusion reactor. - Abstract: It has long been recognised that the shortage of external tritium sources for fusion reactors using D–T, the most promising fusion fuel, requires all such fusion power plants (FPP) to breed their own tritium. It is also recognised that the initial start-up of a fusion reactor will require several kilograms of tritium within a scenario in which radioactive decay, ITER and subsequent demonstrator reactors are expected to have consumed most of the known tritium stockpile. To circumvent this tritium fuel shortage and ultimately achieve steady-state operation for a FPP, it is essential to first accumulate sufficient tritium to compensate for loss due to decay and significant retention in the materials in order to start a new FPP. In this work, we propose to accumulate tritium starting from D–D fusion reactions, since D exists naturally in water, and to gradually build up the D–T plasma targeted in fusion reactor designs. There are two likely D–D fusion reaction channels, (1) D + D → T + p, and (2) D + D → He3 + n. The tritium can be generated via the reaction channel ‘(1)’ and the 2.45 MeV neutrons from ‘(2)’ react with lithium-6 in the breeding blanket to produce more tritium to be fed back into plasma fuel. Quantitative evaluations are conducted for two blanket concepts to assess the feasibility and suitability of this approach to FPP

  20. On electrode erosion in fluorescent lamps during instant start

    Energy Technology Data Exchange (ETDEWEB)

    Hadrath, S.

    2006-09-15

    A fluorescent lamp driven with an 'instant start electronic control gear' starts in a glow mode. In the glow mode, which lasts typically for tens of milliseconds, the cathode fall exceeds hundreds of volts. This causes high energy ion bombardment of the electrode which heats the electrode, and induces a transition from glow to arc mode. In the arc mode the electrode emits thermionically and the cathode fall drops to the 12 - 15 V range. Unfortunately, the high energy ion bombardment during the glow mode leads also to intense sputtering of electrode material, including tungsten as well as emitter. Thus, instant started fluorescent lamps often suffer from early failures due to coil fracture. Therefore, the investigation of tungsten erosion during instant start is necessary and was the main goal of this work. The density of neutral atomic tungsten is determined by laser-induced fluorescence (LIF) and optical emission spectroscopy measurements (OES). Investigations are performed on a low-pressure argon dc discharge and on commercial fluorescent lamps. To include the entire temperature profile along the electrode the diffuse and spot operation modes of the dc lamp are studied experimentally and theoretically. The measured dependencies of the cathode temperature along the coil on the discharge and heating parameters are compared with the calculated results. For the first time the tungsten erosion during instant start of commercial fluorescent lamps was experimentally investigated in this work. The erosion process could be related to sputtering. A reconstruction of the temporal evolution of the absolute tungsten population density of the ground state during the glow mode was presented. The sputtered tungsten density increases immediately with the ignition, reaches a maximum where the discharge contracts at the end of the glow mode, and decreases some milliseconds before the glow-to-arc transition takes place. The maximum tungsten density was observed within a

  1. Healthy Start: a comprehensive health education program for preschool children.

    Science.gov (United States)

    Williams, C L; Squillace, M M; Bollella, M C; Brotanek, J; Campanaro, L; D'Agostino, C; Pfau, J; Sprance, L; Strobino, B A; Spark, A; Boccio, L

    1998-01-01

    Healthy Start is a 3-year demonstration and education research project designed to evaluate the effectiveness of a multidimensional cardiovascular (CV) risk reduction intervention in preschool centers over a 3-year period of time. Two primary interventions are employed. The first is the preschool food service intervention program designed to reduce the total fat in preschool meals and snacks to less than 30% of calories and reduce the saturated fat to less than 10% of calories. The second major intervention is a comprehensive preschool health education curriculum, focused heavily on nutrition. Effectiveness of the intervention will be determined through evaluation of changes in dietary intake of preschool children at school meals and snacks, especially with respect to intake of total and saturated fat. Evaluation of the education component will include assessment of program implementation by teachers, assessment of changes in nutrition knowledge by preschool children, and assessment of changes in home meals that children consume (total and saturated fat content). Blood cholesterol will be evaluated semiannually to evaluate changes that may be due to modification of dietary intake. Growth and body fatness will also be assessed. While substantial efforts have targeted CV risk reduction and health education for elementary school children, similar efforts aimed at preschool children have been lacking. The rationale for beginning CV risk reduction programs for preschool children is based upon the premise that risk factors for heart disease are prevalent by 3 years of age and tend to track over time, most commonly hypercholesterolemia and obesity, both related to nutrition. Since the behavioral antecedents for nutritional risk factors begin to be established very early in life, it is important to develop and evaluate new educational initiatives such as Healthy Start, aimed at the primary prevention of cardiovascular risk factors in preschool children. The purpose of this

  2. Start time variability and predictability in railroad train and engine freight and passenger service employees.

    Science.gov (United States)

    2014-04-01

    Start time variability in work schedules is often hypothesized to be a cause of railroad employee fatigue because unpredictable work start times prevent employees from planning sleep and personal activities. This report examines work start time diffe...

  3. 'From Start to Finnish': Handbook For Exporting A Theatre Play

    OpenAIRE

    Tanskanen, Milka; Mäkinen, Annemari

    2014-01-01

    Exporting Finnish culture is one of the themes the Finnish Ministry of Education and Culture has carried out over the last few years. ‘From Start to Finnish’ project was a mission to strenghten the state of theatre export in Finland. In the project, government subsidised theatres in Finland export their plays to the Edinburgh Festival Fringe, the largest arts festival in the world. The thesis is product-based as the authors created a handbook to combine all the steps to be taken when expo...

  4. Characteristics Contributing to High-Technology Start-Up Success

    DEFF Research Database (Denmark)

    Goslin, L.; Brown, W.; Palm, T.

    1993-01-01

    that the professional venture-capital-funded start-up firm will generally reflect the practices of perceptive management regarding: style, team approach, structure of the firm, market definition, culture, vision, and a formal strategy. Nevertheless, there are some questions about differences those characteristics...... by interview to provide insights on: the entrepreneurial-marketing style utilized, cultural characteristics of the firm, and perspectives of the time horizon of strategy. The representative firms (seven firms to a set) from whom information was solicited were drawn from the U.S. Pacific Northwest), Denmark...

  5. Getting started in business: from fantasy to reality.

    Science.gov (United States)

    Finnigan, S

    1996-01-01

    Numerous theories and concepts of business management are available in the authoriatative literature. Some of the important lessons for getting started in business, and more important, staying in business may not, however, be found there. The practical business realities that influence success are the real-life lessons. They include examining worthwhile motives, applying commonsense approaches, demonstrating value to the customer, and achieving early and sustained profitability. Such lessons and other principles of entrepreneurship must be learned to create a successful beginning and long-term business viability.

  6. Getting started with oVirt 3.3

    CERN Document Server

    Lesovsky, Alexey

    2013-01-01

    Getting Started with oVirt 3.3 has a tutorial-based approach to learning oVirt KVM virtualization. This book will introduce you to the various components of the oVirt engine and will show you how to implement virtualization.This book is designed for technicians and system administrators who are interested in virtualization technology in Linux / UNIX. It is assumed that you have an understanding of virtualization in general as well as what issues it solves. You will also need a basic knowledge of how to work on the command line in Linux.

  7. Genomic and chromatin signals underlying transcription start-site selection

    DEFF Research Database (Denmark)

    Valen, Eivind; Sandelin, Albin Gustav

    2011-01-01

    A central question in cellular biology is how the cell regulates transcription and discerns when and where to initiate it. Locating transcription start sites (TSSs), the signals that specify them, and ultimately elucidating the mechanisms of regulated initiation has therefore been a recurrent theme....... In recent years substantial progress has been made towards this goal, spurred by the possibility of applying genome-wide, sequencing-based analysis. We now have a large collection of high-resolution datasets identifying locations of TSSs, protein-DNA interactions, and chromatin features over whole genomes...

  8. Research Strategies in Science-based Start-ups

    DEFF Research Database (Denmark)

    Valentin, Finn; Dahlgren, Johan Henrich; Lund Jensen, Rasmus

    develop a contingency view on complex problem solving which structures the argument into three steps:1) Characterising the problem architectures addressed by different types of DBFs;2) Testing and confirming that DBFs form requisite research strategies, by which we refer to problem solving approaches......Although biotech start-ups fail or succeed based on their research few attempts have been made to examine if and how they strategize in this core of their activity. Popular views on Dedicated Biotech Firms (DBFs) see the inherent uncertainty of research as defying notions of strategizing, directing...

  9. Starting an Online Business All-in-One For Dummies

    CERN Document Server

    Belew, Shannon

    2011-01-01

    Conquer the online marketplace with this new version of a bestseller! Whether you've thought of starting an online business or you're already selling online, this update to a bestseller presents invaluable advice for getting--and keeping--online customers. Covering everything from creating a business plan and building a customer-friendly site to marketing with Facebook and Twitter, this fun and friendly guide features eleven minibooks that cover online business basics, legal and accounting matters, website design, online and operating issues, Internet security, techniques for boosting sales, s

  10. Starting the automation process by using group technology

    Directory of Open Access Journals (Sweden)

    Jorge Andrés García Barbosa

    2004-09-01

    Full Text Available This article describes starting-up an automation process based on applying group technology (GT. Mecanizados CNC, a company making matallurgical sector products, bases the layout (organisation and disposition of its machinery on the concept of manufacturing cells; production is programmed once the best location for the equipment has been determined. The order of making products and suitable setting up of tools for the machinery in the cells is established, aimed at minimising set up leading to achieving 15% improvement in productivity.

  11. Getting Started: A Call for Storytelling in Family Medicine Education.

    Science.gov (United States)

    Ventres, William; Gross, Paul

    2016-10-01

    In this article we introduce family medicine educators to storytelling as an important teaching tool. We describe how stories are a critical part of the work of family physicians. We review the rationales for family medicine educators to become skilled storytellers. We present the components of effective stories, proposing two different perspectives on how to imagine, construct, and present them. We provide a list of resources for getting started in storytelling and offer two personal vignettes that articulate the importance of storytelling in the authors' respective professional developments. We point the way forward for family medicine educators interested in integrating storytelling into their repertoire of teaching skills.

  12. The study of transient processes in the asynchronous starting of the synchronous motor

    OpenAIRE

    Alexandru Bârlea; Olivian Chiver

    2012-01-01

    Starting synchronous motors can be achieved by several ethods: starting with an auxiliary motor launch, starting in asynchronous regim, by feeding from a variable frequency source, auto-synchronization with the network.. In our case we study the transient processes in a asynchronous regim . In this case the synchronous motor is started like a squirrel cage induction motor . To start, the synchronous motor is equipped with a starting winding cage placed in the pole pieces of polar inducers; la...

  13. Promoting cold-start items in recommender systems.

    Science.gov (United States)

    Liu, Jin-Hu; Zhou, Tao; Zhang, Zi-Ke; Yang, Zimo; Liu, Chuang; Li, Wei-Min

    2014-01-01

    As one of the major challenges, cold-start problem plagues nearly all recommender systems. In particular, new items will be overlooked, impeding the development of new products online. Given limited resources, how to utilize the knowledge of recommender systems and design efficient marketing strategy for new items is extremely important. In this paper, we convert this ticklish issue into a clear mathematical problem based on a bipartite network representation. Under the most widely used algorithm in real e-commerce recommender systems, the so-called item-based collaborative filtering, we show that to simply push new items to active users is not a good strategy. Interestingly, experiments on real recommender systems indicate that to connect new items with some less active users will statistically yield better performance, namely, these new items will have more chance to appear in other users' recommendation lists. Further analysis suggests that the disassortative nature of recommender systems contributes to such observation. In a word, getting in-depth understanding on recommender systems could pave the way for the owners to popularize their cold-start products with low costs.

  14. A Robotic Fish to Emulate the Fast-Start

    Science.gov (United States)

    Currier, Todd; Ma, Ganzhong; Modarres-Sadeghi, Yahya

    2017-11-01

    An experimental study is conducted on a robotic fish designed to emulate the fast-start response. The fish body is constructed of 3D printed ribs and a light spring steel spine. The body is actuated using a series of pressured pistons. A total of four pistons are supplied with pressure through lightweight high pressure service lines. The source of pressure is carbon dioxide with a 700 psi peak operating pressure resulting in a body response that can cycle a c-start maneuver in milliseconds. The motion of the fish is precisely controlled through the use of solenoids with a control signal produced by a programmable microprocessor. The fish is constrained in all translational degrees of freedom but allowed to rotate about a vertical axis. The influence of the point of rotation is studied with different mounting points along the length of the head of the fish. The forces are measured in two perpendicular in-plane directions. A high speed camera is used to capture the response of the fish and the corresponding flow around it. Comparison is made with the kinematics observed in live fish.

  15. Disposition scenarios and safeguardability of fissile materials under START Treaty

    International Nuclear Information System (INIS)

    Pillay, K.K.S.

    1993-01-01

    Under the Strategic Arms Reduction Treaty (START-I) signed in 1991 and the Lisbon Protocol of 1992, a large inventory of fissile materials will be removed from the weapons fuel cycles of the United States and the Former Soviet Union (FSU). The Lisbon Protocol calls for Ukraine, Kazakstan, and Byelarus to become nonnuclear members of the treaty and for Russia to assume the responsibility of the treaty as a nuclear weapons state. In addition, the START-II Treaty, which was signed in 1993 by the United States and Russia, further reduces deployed nuclear warheads and adds to the inventory of excess special nuclear materials (SNM). Because storage of in-tact warheads has the potential for a open-quotes breakout,close quotes it would be desirable to dismantle the warheads and properly dispose of the SNMs under appropriate safeguards to prevent their reentry into the weapons fuel cycle. The SNM recovered from dismantled warheads can be disposed of in several ways, and the final choices may be up to the country having the title to the SNM. Current plans are to store them indefinitely, leaving serious safeguards concerns. Recognizing that the underlying objective of these treaties is to prevent the fissile materials from reentering the weapons fuel cycle, it is necessary to establish a verifiable disposal scheme that includes safeguards requirements. This paper identifies some realistic scenarios for the disposal of SNM from the weapons fuel cycle and examines the safeguardability of those scenarios

  16. Ageing significantly at Temelin start-up process

    International Nuclear Information System (INIS)

    Brumovsky, M.; Zdarek, J.; Hahn, J.

    2002-01-01

    Full text: NPP Temelin is a unique case in Plant Life Management Programme application as it is now only in the period of start-up and thus all measures can be easily prepared and implemented in advance based on the experience of similar plants already in operation. Detailed analyses of potential damaging mechanisms as well as of initial conditions and properties of main components have been already done. Regarding this analysis, several measures have been prepared and put into operation: List of important parameters to be measured, saved and periodically analysed have been prepared - some of these parameters are measured in the framework of standard I and C system; new sets of sensors were installed for some additional ones; Special software for on-line evaluation of stress/temperature conditions and subsequently also fatigue damage in some chosen parts (with flow stratification etc.) have been installed and during reactor start-up tests have been checked; Surveillance specimen programme for reactor pressure vessel material monitoring was modified for better and fuller characterisation of material changes during operation; Ex-vessel neutron flux measurement has been established as a part of surveillance specimen programme. The whole Plant Life Management Programme is governed by a special PLIM Group in the plant with necessary links and responsibilities and rules with other necessary plant departments. (author)

  17. [Inappropriate prescription in older patients: the STOPP/START criteria].

    LENUS (Irish Health Repository)

    Delgado Silveira, Eva

    2009-09-01

    Older people are a heterogeneous group of patients, often with multiple comorbidities for which they are prescribed a large number of drugs, leading to an increased risk of adverse drug reactions (ADR) and drug interactions. This risk is compounded by physiological age-related changes in physiology, changes in drug pharmacokinetics and pharmacodynamics, as well as by disease-related, functional and social issues. Inappropriate prescription of drugs is common in the older individuals and contributes to the increased risk of ADR. Several tools have been developed to detect potentially inappropriate prescription, the most frequently used in Spain being Beers\\' criteria. However, the value of these criteria is limited, especially as they were developed in a different healthcare system. In this article, the Spanish version of a new tool to detect potentially inappropriate prescriptions-STOPP (Screening Tool of Older Person\\'s Prescriptions) and START (Screening Tool to Alert doctors to Right i.e. appropriate, indicated Treatment) criteria-is presented. The creation, development, reliability, and use of these criteria in routine practice is described and discussed. These criteria have shown better sensitivity than Beers\\' criteria in detecting prescription problems and have the added value of being able to detect not only inappropriate prescription of some drugs, but also the omission of well indicated drugs. The STOPP\\/START criteria could become a useful screening tool to improve prescription in older people.

  18. Eccentric LVH healing after starting renal replacement therapy.

    Science.gov (United States)

    Vertolli, Ugo; Lupia, Mario; Naso, Agostino

    2002-01-01

    Hypertension and left ventricular hypertrophy (LVH) are commonly associated in patients with CRF starting RDT. We report a case of eccentric LVH with marked dilatation and subsequent mitral incompetence of +3/4 that disappeared after three months of standard hemodialysis. Mrs SN, 62 years old, starting HD, had an echocardiography because of dyspnoea; the echo showed: dilated left atrium (78 ml/m2), moderately dilated left ventricle with normal systolic function (TDV 81 ml/m2, EF 66%), an increased ventricular mass (120 gr/m2) and a high grade mitral incompetence +3/4. After three months standard RDT and a dry weight only 2 kg less, the patients was normotensive without therapy, a cardiac angiogram with a hemodynamic study was performed as a pre-transplant workout: a normal left ventricle was found with normal systolic function (TDV 66, TSV 17, GS 49, EF 75%), and a perfectly competent mitral valve (reflux disappeared). The coronary angiography did not reveal critical stenosis. A new echocardiography confinned the data of the hemodynamic study: hypertensive cardiomiopathy with normal systolic function. After one year the patient has been transplanted, with a good renal function and the cardiac echo unchanged. Relieving uremic toxicity ameliorated the cardiac performance in this particular patient.

  19. Reasons for Starting and Stopping Electronic Cigarette Use

    Directory of Open Access Journals (Sweden)

    Jessica K. Pepper

    2014-10-01

    Full Text Available The aim of our study was to explore reasons for starting and then stopping electronic cigarette (e-cigarette use. Among a national sample of 3878 U.S. adults who reported ever trying e-cigarettes, the most common reasons for trying were curiosity (53%; because a friend or family member used, gave, or offered e-cigarettes (34%; and quitting or reducing smoking (30%. Nearly two-thirds (65% of people who started using e-cigarettes later stopped using them. Discontinuation was more common among those whose main reason for trying was not goal-oriented (e.g., curiosity than goal-oriented (e.g., quitting smoking (81% vs. 45%, p < 0.001. The most common reasons for stopping e-cigarette use were that respondents were just experimenting (49%, using e-cigarettes did not feel like smoking cigarettes (15%, and users did not like the taste (14%. Our results suggest there are two categories of e-cigarette users: those who try for goal-oriented reasons and typically continue using and those who try for non-goal-oriented reasons and then typically stop using. Research should distinguish e-cigarette experimenters from motivated users whose decisions to discontinue relate to the utility or experience of use. Depending on whether e-cigarettes prove to be effective smoking cessation tools or whether they deter cessation, public health programs may need distinct strategies to reach and influence different types of users.

  20. Reasons for starting and stopping electronic cigarette use.

    Science.gov (United States)

    Pepper, Jessica K; Ribisl, Kurt M; Emery, Sherry L; Brewer, Noel T

    2014-10-03

    The aim of our study was to explore reasons for starting and then stopping electronic cigarette (e-cigarette) use. Among a national sample of 3878 U.S. adults who reported ever trying e-cigarettes, the most common reasons for trying were curiosity (53%); because a friend or family member used, gave, or offered e-cigarettes (34%); and quitting or reducing smoking (30%). Nearly two-thirds (65%) of people who started using e-cigarettes later stopped using them. Discontinuation was more common among those whose main reason for trying was not goal-oriented (e.g., curiosity) than goal-oriented (e.g., quitting smoking) (81% vs. 45%, p reasons for stopping e-cigarette use were that respondents were just experimenting (49%), using e-cigarettes did not feel like smoking cigarettes (15%), and users did not like the taste (14%). Our results suggest there are two categories of e-cigarette users: those who try for goal-oriented reasons and typically continue using and those who try for non-goal-oriented reasons and then typically stop using. Research should distinguish e-cigarette experimenters from motivated users whose decisions to discontinue relate to the utility or experience of use. Depending on whether e-cigarettes prove to be effective smoking cessation tools or whether they deter cessation, public health programs may need distinct strategies to reach and influence different types of users.

  1. Behavioral and Psychosocial Characteristics Among Head Start Childcare Providers.

    Science.gov (United States)

    Ling, Jiying

    2017-01-01

    The aim of the study was twofold: (a) describe behavioral and psychosocial characteristics of Head Start childcare providers including technology use, physical activity, nutrition, depression, and quality of life and (b) examine associations among these characteristics. Using a cross-sectional design, a nonrandom sample of 80 Head Start childcare providers completed an online survey via SurveyMonkey. About 80.1% were overweight or obese. Nearly all had a computer or smartphone. About 55% met the national physical activity recommendation of 150 min/week. Approximately 56.2% did not know the recommended daily servings of fruits and vegetables, and 26.3% had ≥3 servings of vegetables per day. About 38.8% had major depression or dysthymia, and 31.3% had depressive symptoms. The top two perceived health needs were weight loss and stress management. Providing a health promotion and stress management program to childcare providers may benefit both providers and children, considering the strong influence of teachers on children.

  2. Start-up and operation of Laguna Verde-2

    International Nuclear Information System (INIS)

    Torres Ramirez, J.F.

    1996-01-01

    The 665 MWe Laguna Verde-2 nuclear generating unit was accepted into commercial operation on April 10, 1995. The boiling water reactor plant by General Electric (GE) was first synchronized with the grid on November 11, 1994. Laguna Verde-2 is identical with Laguna Verde-1 on the same site. That unit had gone critical for the first time in November 1988 and had first been synchronized with the power grid on April 13, 1989. Commercial operation of Laguna Verde-1 had been started on July 29, 1990. Mexico's only nuclear power plant had been built 70 km north of Veracruz on the east coast and had been scheduled to start operation in 1976. As the Mexican nuclear power program was reduced, the scheduled commissioning dates suffered more and more delays. In the full of 1987, the investigation by the Operational Safety Review Team (Osart) of the International Atomic Energy Agency (IAEA) had indicated that the safety requirements of installations and equpiment were met, and that the whole plant was well prepared for fueling. In mid-1988, the Mexican Government had issued the permit to fuel the Laguna Verde-1 reactor. The contract to build the two units had been awarded in 1972/73. No other nuclear power plants are currently under construction or in the planning phase in Mexico. (orig.) [de

  3. Hot-start Giant Planets Form with Radiative Interiors

    Energy Technology Data Exchange (ETDEWEB)

    Berardo, David; Cumming, Andrew, E-mail: david.berardo@mcgill.ca, E-mail: andrew.cumming@mcgill.ca [Department of Physics and McGill Space Institute, McGill University, 3600 rue University, Montreal, QC H3A 2T8 (Canada)

    2017-09-10

    In the hot-start core accretion formation model for gas giants, the interior of a planet is usually assumed to be fully convective. By calculating the detailed internal evolution of a planet assuming hot-start outer boundary conditions, we show that such a planet will in fact form with a radially increasing internal entropy profile, so that its interior will be radiative instead of convective. For a hot outer boundary, there is a minimum value for the entropy of the internal adiabat S {sub min} below which the accreting envelope does not match smoothly onto the interior, but instead deposits high entropy material onto the growing interior. One implication of this would be to at least temporarily halt the mixing of heavy elements within the planet, which are deposited by planetesimals accreted during formation. The compositional gradient this would impose could subsequently disrupt convection during post-accretion cooling, which would alter the observed cooling curve of the planet. However, even with a homogeneous composition, for which convection develops as the planet cools, the difference in cooling timescale will change the inferred mass of directly imaged gas giants.

  4. A fresh start of nuclear safety regulation and international perspective

    International Nuclear Information System (INIS)

    Oshima, Kenzo

    2013-01-01

    It should be explained more to the outside modestly the Fukushima nuclear accident would be a man-made complex disaster, which might be reluctant to do but not be neglected. Utmost efforts to change inward-looking attitude and reform safety culture should be done so as to prevent superficial reflection of the Fukushima nuclear accident. Since all nuclear regulatory functions ('3S': safety, security, safeguards) were integrated in Nuclear Regulation Authority (NRA), NRA and secretariat of NRA became more responsible for international response, and strengthening of organization system and human resources development would be an urgent necessity. This article described present stage of NRA focusing on international dimension including personal views. Overseas strong concern over the Fukushima nuclear accident and international communications were reviewed. The Fukushima nuclear accident started from natural disaster and enlarged as a man-made complex disaster with many human factors (mainly inaction, wilful negligence) overlapping and safety culture flawed. Examples of overseas and Japanese action plan to learn and absorb lessons from the Fukushima accident were introduced. NRA's started activities on inviting IAEA's IRRS and OPPAS as soon as ready, strengthening nuclear security measures, safeguards to prevent nuclear proliferation, bilateral cooperation and international advisors were also presented. (T. Tanaka)

  5. Promoting Cold-Start Items in Recommender Systems

    Science.gov (United States)

    Liu, Jin-Hu; Zhou, Tao; Zhang, Zi-Ke; Yang, Zimo; Liu, Chuang; Li, Wei-Min

    2014-01-01

    As one of the major challenges, cold-start problem plagues nearly all recommender systems. In particular, new items will be overlooked, impeding the development of new products online. Given limited resources, how to utilize the knowledge of recommender systems and design efficient marketing strategy for new items is extremely important. In this paper, we convert this ticklish issue into a clear mathematical problem based on a bipartite network representation. Under the most widely used algorithm in real e-commerce recommender systems, the so-called item-based collaborative filtering, we show that to simply push new items to active users is not a good strategy. Interestingly, experiments on real recommender systems indicate that to connect new items with some less active users will statistically yield better performance, namely, these new items will have more chance to appear in other users' recommendation lists. Further analysis suggests that the disassortative nature of recommender systems contributes to such observation. In a word, getting in-depth understanding on recommender systems could pave the way for the owners to popularize their cold-start products with low costs. PMID:25479013

  6. Start-up First Term Sheet: Stumbling Blocks to Avoid

    Directory of Open Access Journals (Sweden)

    Amalyan Nataly D.

    2018-01-01

    Full Text Available Start-up relationships with business angel and/or venture capital are similar to a marriage – but with a divorce in mind. The latter necessitates a proper prenuptial agreement signing at the very beginning of the relations. In case of business angel and/or venture capital we are speaking about Term sheet, determining pricing, powers and duties of the board, as well as information, participation and protective rights for the partners. Standard Term sheet consists of three buckets of provisions, defining: (i terms impacting start-up valuation and economic division of profits and proceeds upon a liquidity event, (ii terms impacting control over decision making and (iii investor protection terms. This article focuses on financial and economic aspects of funding agreement, exposing some tricky parts of the Term sheet, threatening to transform potential win-win deals into rupture of relations, crash of the company or even legal battles. The results of the analysis are used to substantiate growing in popular appeal thesis that raising too much money can be detrimental for a startup.

  7. Starting a business as a nurse consultant: practical considerations.

    Science.gov (United States)

    Papp, E M

    2000-03-01

    Nursing experience translates well to self employment in the occupational and environmental health field. However, nurses must conduct a self assessment to determine whether owning a business is a good fit for their personality and work style. Exploring which services to offer is the next step in starting a business and consists of determining not only which service to offer (e.g., writing policies or protocols, providing clinical services) but also which type of consultation model to use (i.e., purchase of expertise, doctor/client, process consultation). Every business must have a plan. A business plan is essential to starting a business. It solidifies the entrepreneur's focus, lays the foundation for the business, provides a tool for evaluating success, and is a strong tool for soliciting financial support. The name of the business is an important consideration because it is often the first contact the customers have with the occupational health nurse consultant. The name must be descriptive, appropriate, and memorable.

  8. Storage evaporator for vehicles with start-stop technology; Speicherverdampfer fuer Fahrzeuge mit Start-Stopp-Funktion

    Energy Technology Data Exchange (ETDEWEB)

    Wawzyniak, Markus; Link, Joachim [Behr GmbH und Co. KG, Stuttgart (Germany)

    2013-04-15

    Today, the use of engine start-stop technology - a system designed to cut fuel consumption when the vehicle stops or, in future applications, when vehicles are in coasting or ''sailing'' mode - is gaining ground in more and more vehicle classes. Shutting off the internal combustion engine, though, detrimentally affects cabin air conditioning because the belt-driven A/C compressor is likewise deactivated, thus bringing the vapor compression process to a standstill. As a result, during extended stop periods and in warm weather vent temperatures and air humidity rapidly increase.

  9. The Impact of Head Start on Children, Families and Communities. Final Report of the Head Start Evaluation, Synthesis and Utilization Project.

    Science.gov (United States)

    McKey, Ruth Hubbell; And Others

    Including all Head Start research (both published and unpublished) and using, when possible, the statistical technique of meta-analysis, this final report of the Head Start Evaluation, Synthesis, and Utilization Project presents findings on the impact of Head Start on children's cognitive and socioemotional development, on child health and health…

  10. BANKRUPTCY - A POSSIBLE NEW START FOR THE SMALL BUSINESS?

    Directory of Open Access Journals (Sweden)

    LAURA GIURCA VASILESCU

    2010-01-01

    Full Text Available Many factors (internal and external can make a business vulnerable. In the context of the international financial crisis, the firms, and especially the small and mediume enterprises (SMEs have to face new challenges. Smaller businesses are particularly prone to financial difficulties as they often lack resources to adapt to the changing market conditions. Very often the business distress or even business failure is not yet sufficiently understood as a normal economic development and an opportunity for a new start. In order to take the full potential of business in Europe, should be created the background that genuinely talented entrepreneurs have every opportunity to get another second chance. The European Commission lays out proposals to actively help businesses at financial risk and prevent bankruptcy. In the same time, the national insolvency systems should provide more options for restructuring and rescue. Thus, EU supports simpler and faster procedures for bankruptcy and encourages giving a second chance to honest entrepreneurs who have failed.

  11. Start App: a coding experience between primary and secondary school

    Directory of Open Access Journals (Sweden)

    Filippo Bruni

    2016-04-01

    Full Text Available The paper presents a coding experience in primary school (“Colozza” in Campobasso. Within the theoretical framework offered by computational thinking, using App Inventor, it was created a calculator for smartphone in the Android environment. High school students (from a technical secondary school guided the pupils in primary school, making an interesting form of cooperation between primary and secondary schools. Start App: una esperienza di coding tra scuola primaria e scuola secondariaIl contributo presenta una esperienza di coding nella scuola primaria dell’Istituto Comprensivo statale “Colozza” di Campobasso. All’interno della cornice teorica offerta dal pensiero computazionale, utilizzando App Inventor, è stata realizzata una calcolatrice per smartphone in ambiente Android. A guidare gli allievi della primaria sono stati gli studenti dell’Istituto Tecnico Industriale “Marconi” di Campobasso realizzando una interessante forma di collaborazione tra istituti scolastici di ordine diverso.

  12. Getting Started with GEO, CouchDB, and Nodejs

    CERN Document Server

    Thompson, Mick

    2011-01-01

    Today's mobile devices have GPS and standard APIs to give you access to coordinates-but what can you do with that data? With this concise book, application developers learn how to work with location data quickly and easily, using Node.js, CouchDB, and other open source tools and libraries. Node.js makes it simple to run event code on the Web, and the CouchDB document-oriented database lets you store location data and perform complex queries on it quickly. You'll learn how to get started with these tools, and then use them together to build an example project called MapChat, using HTML and Ja

  13. Loviisa starts low-level operating waste disposal in 1997

    International Nuclear Information System (INIS)

    Snellman, J.

    1996-01-01

    At an early stage Imatran Voima Oy (IVO) decided to construct a waste repository for Loviisa NPP. The suitability of the power plant site for final disposal of low- and intermediate- level operating waste was studied. In the site report in 1982 the plant site was found to be geologically suitable and economically feasible for construction. The necessary preparations started in 1992. The repository will be constructed in three phases. The first phase will cover the transport tunnel, construction of one maintenance waste tunnel and the excavation of another maintenance waste tunnel together with a hall for solidified wastes. This phase will be finished by the end of 1996. During the second phase in the beginning of next century the remaining already excavated rooms will be furnished. Finally in the third phase the repository will be extended for the decommissioning waste somewhere around years 2020-2025. (3 figs., 1 tab.)

  14. Who started first? Bird species visiting novel birdfeeders.

    Science.gov (United States)

    Tryjanowski, Piotr; Morelli, Federico; Skórka, Piotr; Goławski, Artur; Indykiewicz, Piotr; Pape Møller, Anders; Mitrus, Cezary; Wysocki, Dariusz; Zduniak, Piotr

    2015-07-07

    Adapting to exploit new food sources may be essential, particularly in winter, when the impact of food limitation on survival of individuals is critical. One of the most important additional sources of food for birds in human settlements is birdfeeders. At a large spatial scale, we experimentally provided birdfeeders with four different kinds of food to analyze exploitation and use of a novel food supply provided by humans. Nine species started foraging at the new birdfeeders. The species that exploited the new feeders the fastest was the great tit. Use of novel food sources was faster in urban habitats and the presence of other feeders reduced the time until a new feeder was located. Urbanization may be associated with behavioural skills, technical innovations and neophilia resulting in faster discovery of new food sources. This process is accelerated by the experience of feeder use in the vicinity, with a strong modifying effect of the number of domestic cats.

  15. Start-up of the ohmic phase in JET

    International Nuclear Information System (INIS)

    Tanga, A.; Christiansen, J.P.; Cordey, J.G.; Ejima, S.; Kellman, A.; Lazzaro, E.; Lomas, P.J.; Thomas, P.R.

    1985-01-01

    JET has been designed to permit the study of plasmas in which alphaparticle heating is a significant part of the power balance. In order to have a sufficient thermonuclear yield and to trap the resulting alphaparticles, JET is similar in its dimensions and plasma current to the next generation of reactor-like devices such as NET, FER and INTOR. For this reason, the authors see the results from the study of the start-up of ohmically heated plasmas in JET as highly relevant. Discussed is the range that has been achieved in all major parameters with ohmic heating. Experiences with the wall conditioning technique and the results of ion cyclotron heating experiments in JET are outlined. This paper also describes the stages of plasma formation, current rise and ohmic flat-top

  16. Getting started with Citrix VDI-in-a-Box

    CERN Document Server

    Brown, Stuart Arthur

    2013-01-01

    A practical and fast-paced guide that gives you all the information you need to simplify and streamline virtual desktops so you get a production-quality solution while instantly lowering your costs and improving security.Getting Started with Citrix VDI-in-a-Box is great for IT professionals who are new to VDI-in-a-Box and who are looking for a good grounding in the product. You may be planning to research VDI-in-a-Box in more detail, or you may be tasked with researching how VDI-in-a-Box could improve the productivity of your organization. No prior knowledge of VDI-in-a-Box is required, just a

  17. So You Want to Start a Peer Online Writing Center?

    Directory of Open Access Journals (Sweden)

    Christine Rosalia

    2013-03-01

    Full Text Available The purpose of this article is to share lessons learned in setting up three different peer online writing centers in three different contexts (EFL, Generation 1.5, and ESL. In each center the focus was on the language learner as a peer online writing advisor and their needs in maintaining centers “for and by” learners. Technology affordances and constraints for local contexts, which promote learner autonomy, are analyzed. The open-source platforms (Moodle, Drupal, and Google Apps are compared in terms of usability for peer writing center work, particularly centers where groups co-construct feedback for writers, asynchronously. This paper is useful for readers who would like a head start or deeper understanding of potential logistics and decision-making involved in establishing a peer online writing center within coursework and/or a self-access learning center.

  18. Oil field rejuvenation work starts at 14 project sites

    International Nuclear Information System (INIS)

    Petzet, G.A.

    1992-01-01

    This paper reports that the U.S. Department of Energy and oil and gas companies have released more information about a joint effort to rejuvenate aging U.S. oil fields in danger of abandonment. Work is starting on 14 demonstration projects that could recover 21 million bbl of oil from the fluvial dominated deltaic (FDD) reservoirs in which they are conducted. Wider application of the same techniques, if they are successful, could results in addition of 6.3 billion bbl of reserves, nearly 25% of U.S. crude oil reserves. A multidisciplinary team approach is to be used, with as many as 11 operators, service companies, universities, or state agencies participating in each project. All of the projects will culminate in extensive technology transfer activities. Here are descriptions of the projects gleaned from public abstracts provided by the DOE contractors

  19. UASB reactor start up in real scale for malting effluent

    International Nuclear Information System (INIS)

    Lopez, I.; Passeggi, M.; Boix, C.; Barcia, R.; Borzacconi, L.; Liebermann, L.

    2005-01-01

    An Imhoff tank was reconstructed into a 250 m3 UASB reactor in order to treat a malting plant wastewater.The UASB was inoculated with sludge from an anaerobic lagoon used for slaughterhouse wastewater treatment.The fat present in the inoculated sludge did not affect the start up performance. After two month of operation the reactor achieved full load with COD removal higher than 80% and a biogas production of 300 m3/day. The mean diameter of granules was 0a.milimeters and the Specific Methanogenic Activity was 0.25 g COD/gVSS.d The banquet development throughout time (solids concentrations at different heights, granule size, methanogenic activity) was monitored. A yield coefficient of 0.09 gVSS/g COD rem was found

  20. Regenerative BBU starting currents in standing wave cavities

    International Nuclear Information System (INIS)

    Vetter, A.M.; Buller, T.L.

    1992-01-01

    An analytical method for determining regenerative beam breakup (BBU) starting current, in which the contributions of single-cell field configuration and multi-cell structure mode are separated, is described. The field configuration within each cell is determined to close approximation through the use of mesh codes, which also relate the wall losses to the voltage drop along the beam path. The cell-to-cell amplitude variation may be determined by bead pull measurements on model cavities, or by assuming idealized structure modes. As an example, the I S Q L product for TM 110 -like modes of a 433-MHz, 5-cell, slot-coupled cavity is obtained. (author). 3 figs

  1. Start of new Research and Innovation Programme, Horizon 2020

    CERN Multimedia

    2013-01-01

    The overall EU budget for 2014-2020 was approved on 20 November, with €79 billion allocated for the Horizon 2020 Research and Innovation programme.   The first calls and final work programmes in Horizon 2020 will be published on 11 December 2013 and the programme will officially start on 1 January 2014. In preparation for the next major programme, the CERN EU Projects Office has launched a redesigned website to keep you informed and to alert you to opportunities in Horizon 2020: cerneu.web.cern.ch. Organised by Euresearch, the Swiss launch event will take place from 14 to 17 January 2014. This four-day conference will offer the possibility to discover the new European Framework Programme for Research and Innovation. The event is open for registration: www.launch-h2020.ch.

  2. Tips for starting your own nurse practitioner practice.

    Science.gov (United States)

    Calmelat, A

    1993-04-01

    The decision to open a nurse practitioner practice is often difficult to make. Success depends on the possession of specific resources, such as adequate skills, finances, emotional support and the desire to be one's own boss. These skills will be critical as the NP develops a business plan and a budget, and makes important decisions, such as the form the business will take: sole proprietorship, partnership or corporation. Using external resources such as attorneys and accountants is also useful, especially when tackling issues of licenses, taxes and insurance. Start-up costs can be kept to a minimum with creativity and used equipment. In-house laboratories and reference laboratories must conform to strict regulations. A practice without established patients will need to market services aggressively through a successful mix of product, price, place and promotion. Patients' acceptance of the NP office will be enhanced by smooth patient flow, adequate space and cleanliness.

  3. Start To End Simulation for the SPARX Project

    CERN Document Server

    Vaccarezza, Cristina; Boscolo, Manuela; Ferrario, Massimo; Fusco, Valeria; Giannessi, Luca; Migliorati, Mauro; Palumbo, Luigi; Quattromini, Marcello; Ronsivalle, Concetta; Serafini, Luca; Spataro, Bruno; Vescovi, Mario

    2005-01-01

    The first phase of the SPARX project now funded by Government Agencies, is an R&D activity focused on developing techniques and critical components for future X-ray facilities. The aim is the generation of electron beams with the ultra-high peak brightness required to drive FEL experiments. The FEL source realization will develop along two lines: (a) the use of the SPARC high brightness photoinjector to test RF compression techniques and the emittance degradation in magnetic compressors due to CSR, (b) the production of radiation in the range of 3-5 nm, both in SASE and SEEDED FEL configurations, in the so called SPARXINO test facility, upgrading the existing Frascati 800 MeV LINAC. In this paper we present and discuss the preliminary start to end simulations results.

  4. Start-up of Rapsodie; Le demarrage de Rapsodie

    Energy Technology Data Exchange (ETDEWEB)

    Pontier, R [Commissariat a l' Energie Atomique, 13 - Cadarache (France). Centre d' Etudes Nucleaires

    1967-07-01

    After giving a general description of Rapsodie this report presents the conditions in which the start-up occurred and in which the tests were carried out. A chronological account is given of the operations and of the main events which occurred. The modifications made to the reactor during this period are described and a synthesis of the results obtained is presented. (author) [French] Apres avoir donne de RAPSODIE une description tres generale, ce rapport expose le cadre dans lequel ont ete effectues le demarrage et les essais de l'installation, fait un historique du deroulement des operations et des principaux evenements qui sont intervenus, indique les modifications apportees au reacteur au cours de cette periode et presente une synthese des resultats obtenus. (auteur)

  5. Why does inflation start at the top of the hill?

    International Nuclear Information System (INIS)

    Hawking, S.W.; Hertog, Thomas

    2002-01-01

    We show why the universe started in an unstable de Sitter state. The quantum origin of our universe implies one must take a 'top down' approach to the problem of initial conditions in cosmology, in which the histories that contribute to the path integral depend on the observable being measured. Using the no boundary proposal to specify the class of histories, we study the quantum cosmological origin of an inflationary universe in theories such as trace anomaly driven inflation in which the effective potential has a local maximum. We find that an expanding universe is most likely to emerge in an unstable de Sitter state, by semiclassical tunneling via a Hawking-Moss instanton. Since the top down view is forced upon us by the quantum nature of the universe, we argue that the approach developed here should still apply when the framework of quantum cosmology will be based on M theory

  6. TFTR Mirnov coil analysis at plasma start-up

    International Nuclear Information System (INIS)

    Harley, T.R.; Buchenauer, D.A.; Coonrod, J.; McGuire, K.M.

    1986-01-01

    The methods for finding poloidal and toroidal numbers of MHD oscillations from Mirnov coils are reviewed and modified. Examples of various MHD phenomena occurring during start-up on TFTR are illustrated. It is found that the MHD mode structure best fits a model with the toroidal correction included. A new algorithm which finds m,n numbers can accommodate toroidal effects which are manifested in the phase data. The algorithm can find m,n numbers with a given toroidal correction parameter lambda', (lambda' = 0 → cylindrical). This algorithm is also used to find the optimal value of lambda' automatically, eliminating the need for ''guesswork.'' The algorithm finds the best parameters to the fit much faster than more conventional computational techniques. 9 refs., 21 figs., 2 tabs

  7. Modelling magnetic laminations under arbitrary starting state and flux waveform

    International Nuclear Information System (INIS)

    Bottauscio, Oriano; Chiampi, Mario; Ragusa, Carlo

    2005-01-01

    A numerical model able to predict the behaviour of a magnetic sheet under arbitrary supply conditions has been developed. The electromagnetic field problem is formulated in terms of an electric vector potential, which provides the magnetic field strength evolution. The hysteretic behaviour of the material is represented through the dynamic Preisach model where the activation law of the bi-state operators is modified in order to guarantee a smooth response. The problem has been solved through a time step procedure using the fixed Point technique for handling nonlinearity. The model has been validated by comparison with suitable experiments and it is applied to the investigation of the influence of the materials' starting state on the magnetic behaviour

  8. Careers at Biotech Start-Ups and in Entrepreneurship.

    Science.gov (United States)

    Froshauer, Susan

    2017-11-01

    The world of biotechnology "start-ups" and entrepreneurship offers exciting new avenues for driving state-of-the-art research using an arsenal of multidisciplinary skills, whether your role is as part of a team or as a leader. Although traditionally these positions may not be as secure as those offered by some of the larger companies, the small start-up culture provides opportunities for contributing at many levels to a wide range of responsibilities: from scientific discovery to delivery of proof of concept and intellectual property; from analysis of market opportunities and competitive intelligence to creation of time lines and business plans for a first product. Often, if you get in on the ground level, you get to validate your own concept, pitch to potential investors, argue value, build a team, engage advisors, and then, with funding in hand, launch an entirely new research and development (R&D) enterprise. Many of the skills and much of the experience gained while pursuing a graduate degree can be put to good use in these arenas as well. This path, however, is not for the faint of heart; it requires not only a strong scientific background and organizational skills, but also the ability to work well on a team, excellent communication skills, and persistence when faced with delays or disappointment. With increasing responsibilities in the small company come the requirements for aptitudes for leadership, strategic and financial planning, networking, negotiating, and managing both projects and personnel. Copyright © 2017 Cold Spring Harbor Laboratory Press; all rights reserved.

  9. School Readiness in Children Living in Non-Parental Care: Impacts of Head Start

    Science.gov (United States)

    Lipscomb, Shannon T.; Pratt, Megan E.; Schmitt, Sara A.; Pears, Katherine C.; Kim, Hyoun K.

    2013-01-01

    The current study examines the effects of Head Start on the development of school readiness outcomes for children living in non-parental care. Data were obtained from the Head Start Impact Study, a randomized controlled trial of Head Start conducted with a nationally representative sample of Head Start programs and families. The sample included…

  10. Open-Start Mathematics Problems: An Approach to Assessing Problem Solving

    Science.gov (United States)

    Monaghan, John; Pool, Peter; Roper, Tom; Threlfall, John

    2009-01-01

    This article describes one type of mathematical problem, open-start problems, and discusses their potential for use in assessment. In open-start problems how one starts to address the problem can vary but they have a correct answer. We argue that the use of open-start problems in assessment could positively influence classroom mathematics…

  11. Preliminary analysis of start up characteristics on SPWR with NESSY (Nuclear ship Engineering Simulation SYstem)

    International Nuclear Information System (INIS)

    Kusunoki, Tsuyoshi; Kyouya, Masahiko; Sako, Kiyoshi

    1993-09-01

    NESSY (Nuclear ship Engineering Simulation SYstem) has been developed to design advanced marine reactors. SPWR (System integrated PWR) has been designed by JAERI. It doesn't have control rod, and starts up by dilution of boron. we analyzed start up behavior of SPWR by NESSY, and evaluated the safety characteristics on start up and appropriate range of start up rate. (author)

  12. Decision Enhancement Services for Small and Medium Enterprise Start-Ups in Uganda

    NARCIS (Netherlands)

    Sol, H G; Basaza, Habinka; Sprague, Ralph H.

    2012-01-01

    While start-up firms create a substantial economic impact on most economies, the failure rate of start-up firms seems to remain high due to inadequate agile decision services. Deciding to start-up mining Small and Medium Enterprises (SME) is a challenging task in Uganda. Research on SME start-up

  13. 34 CFR 200.80 - Migrant Education Even Start Program definition.

    Science.gov (United States)

    2010-07-01

    ... 34 Education 1 2010-07-01 2010-07-01 false Migrant Education Even Start Program definition. 200.80... DISADVANTAGED Even Start Family Literacy Program § 200.80 Migrant Education Even Start Program definition. Eligible participants under the Migrant Education Even Start Program (MEES) must meet the definitions of a...

  14. Planning and Reviewing for Success. Training Guides for the Head Start Learning Community.

    Science.gov (United States)

    Aspen Systems Corp., Rockville, MD.

    This guide offers Head Start staff a blueprint for developing the skills and methods necessary for a Head Start program's planning and review process. The guide stresses the need for Head Start administrative and managerial leadership to maintain a holistic, integrated approach; use the strength and resources of Head Start team members; identify…

  15. Commissioning and start-up of RA-8 critical assembly

    International Nuclear Information System (INIS)

    Lorenzo, N. de; Diaz, C.; Facchini, G.; Fernandez, C.; Fittipaldi, A.; Juracich, R.; Levanon, I.; Manceda, J.; Martinez, J.; Mogdan, R.; Perez, J.; Scarnichia, E.; Blaumann, H.; Gennuso, G.; Scotti, G.

    1999-01-01

    The RA-8 critical assembly was designed as one of the experimental facilities for the CAREM Reactor Project. This paper describes the activities developed during the cold and hot commissioning, pointing out the difficulties and the solutions applied (some of them original ones). Moreover, this paper will show the main features of the newest nuclear installation of CNEA making a brief description of its characteristics. Among the special circumstances related to the commissioning that are described in the paper we can mention the following: 1. The facility shares the building with the Thermohydraulic Assay Laboratory (L.E.T.), another experimental facility of CAREM, and thus some shared systems have already been working for many years before this start up. Special procedures for these systems were designed to verify the proper functioning under the new requirements. 2. A new driving mechanism, based in hydraulic cylinders, was used to move the control rods. The criteria for acceptance and a validation of the procedure completeness have been carried out. 3. The implementation of a power measurement system based in neutron noise. 4. Measurement of Power Distribution using direct gamma counting from the fuel elements. 5. The commissioning was interrupted for a ten-month period because the personnel involved had to carry out the commissioning of the Egyptian Research Reactor 2. Also, the common activities during a commissioning are described, pointing out the major steps carried out and the results obtained. The following are examples of these activities: 1. Environmental dose survey (before fuel loading and during other stages). 2. Test of equipment and systems isolated from the rest of the plant. 3. Integrated system test (two or more systems working at the same time). 4. Start-up and power operation simulations before fuel loading. 5. Fuel loading strategy during the approximation to criticality by mass. 6. Modification of systems' components to improve the

  16. Starting Point: Linking Methods and Materials for Introductory Geoscience Courses

    Science.gov (United States)

    Manduca, C. A.; MacDonald, R. H.; Merritts, D.; Savina, M.

    2004-12-01

    Introductory courses are one of the most challenging teaching environments for geoscience faculty. Courses are often large, students have a wide variety of background and skills, and student motivation can include completing a geoscience major, preparing for a career as teacher, fulfilling a distribution requirement, and general interest. The Starting Point site (http://serc.carleton.edu/introgeo/index.html) provides help for faculty teaching introductory courses by linking together examples of different teaching methods that have been used in entry-level courses with information about how to use the methods and relevant references from the geoscience and education literature. Examples span the content of geoscience courses including the atmosphere, biosphere, climate, Earth surface, energy/material cycles, human dimensions/resources, hydrosphere/cryosphere, ocean, solar system, solid earth and geologic time/earth history. Methods include interactive lecture (e.g think-pair-share, concepTests, and in-class activities and problems), investigative cases, peer review, role playing, Socratic questioning, games, and field labs. A special section of the site devoted to using an Earth System approach provides resources with content information about the various aspects of the Earth system linked to examples of teaching this content. Examples of courses incorporating Earth systems content, and strategies for designing an Earth system course are also included. A similar section on Teaching with an Earth History approach explores geologic history as a vehicle for teaching geoscience concepts and as a framework for course design. The Starting Point site has been authored and reviewed by faculty around the country. Evaluation indicates that faculty find the examples particularly helpful both for direct implementation in their classes and for sparking ideas. The help provided for using different teaching methods makes the examples particularly useful. Examples are chosen from

  17. Quantifying the Effect of Fast Charger Deployments on Electric Vehicle Utility and Travel Patterns via Advanced Simulation: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Wood, E.; Neubauer, J.; Burton, E.

    2015-02-01

    The disparate characteristics between conventional (CVs) and battery electric vehicles (BEVs) in terms of driving range, refill/recharge time, and availability of refuel/recharge infrastructure inherently limit the relative utility of BEVs when benchmarked against traditional driver travel patterns. However, given a high penetration of high-power public charging combined with driver tolerance for rerouting travel to facilitate charging on long-distance trips, the difference in utility between CVs and BEVs could be marginalized. We quantify the relationships between BEV utility, the deployment of fast chargers, and driver tolerance for rerouting travel and extending travel durations by simulating BEVs operated over real-world travel patterns using the National Renewable Energy Laboratory's Battery Lifetime Analysis and Simulation Tool for Vehicles (BLAST-V). With support from the U.S. Department of Energy's Vehicle Technologies Office, BLAST-V has been developed to include algorithms for estimating the available range of BEVs prior to the start of trips, for rerouting baseline travel to utilize public charging infrastructure when necessary, and for making driver travel decisions for those trips in the presence of available public charging infrastructure, all while conducting advanced vehicle simulations that account for battery electrical, thermal, and degradation response. Results from BLAST-V simulations on vehicle utility, frequency of inserted stops, duration of charging events, and additional time and distance necessary for rerouting travel are presented to illustrate how BEV utility and travel patterns can be affected by various fast charge deployments.

  18. FloorspaceJS - A New, Open Source, Web-Based Geometry Editor for Building Energy Modeling (BEM): Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Macumber, Daniel L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Horowitz, Scott G [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Schott, Marjorie [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Nolan, Katie [Devetry; Schiller, Brian [Devetry

    2018-03-19

    Across most industries, desktop applications are being rapidly migrated to web applications for a variety of reasons. Web applications are inherently cross platform, mobile, and easier to distribute than desktop applications. Fueling this trend are a wide range of free, open source libraries and frameworks that make it incredibly easy to develop powerful web applications. The building energy modeling community is just beginning to pick up on these larger trends, with a small but growing number of building energy modeling applications starting on or moving to the web. This paper presents a new, open source, web based geometry editor for Building Energy Modeling (BEM). The editor is written completely in JavaScript and runs in a modern web browser. The editor works on a custom JSON file format and is designed to be integrated into a variety of web and desktop applications. The web based editor is available to use as a standalone web application at: https://nrel.github.io/openstudio-geometry-editor/. An example integration is demonstrated with the OpenStudio desktop application. Finally, the editor can be easily integrated with a wide range of possible building energy modeling web applications.

  19. Deuterium concentration deterioration in feed synthesis gas from ammonia plant to heavy water plant (Preprint No. ED-5)

    International Nuclear Information System (INIS)

    Sah, A.K.

    1989-04-01

    Heavy Water Plant (Thal) is designed for 110 T/ Year capacity (55 T/Year each stream), with inlet deuterium concentration of feed synthesis gas at 115 ppm and depleted to 15 ppm. During first start up of plant the inlet concentration to feed synthesis gas was about 97 ppm. At that time the rich condensate recirculation was not there. To make the effective recirculation of deuterium rich condensate and minimum posssible losses some modifications were carried out in ammonia plant. Major ones are: (i)Demineralised (DM) water export for heavy water plant and urea plant which was having deuterium rich DM water connection was connected with DM water of urea plant which is not rich in deuterium, (ii)Sample cooler pump suction was connected with raw water, (iii)Ammonia plant line No.II condensate stripper was rectified during annual shut down to avoid excessive steam venting from its top and other draining, and (iv)Stripper condensate directly connected to make up water bypassing open settler to avoid evaporation and diffusion losses. With these modifications the deuterium concentration in feed synthesis gas improved to about 105 ppm. To improve it to 115 ppm, further modifications are suggested. (author). 5 figs

  20. Targeting health visitor care: lessons from Starting Well.

    Science.gov (United States)

    Wright, C M; Jeffrey, S K; Ross, M K; Wallis, L; Wood, R

    2009-01-01

    UK child health promotion guidelines expect health visitors to assess family needs before new babies are aged 4 months and offer targeted care on that basis thereafter. Data from an intensive family support programme were used to assess how accurately family needs can be predicted at this stage. A population based cohort of 1202 families with new babies receiving an intensive health visiting programme. Analysis of routinely recorded data. Starting Well project, Glasgow, UK. Health visitor rating of family needs. Families receiving high visiting rates or referred to social work services. Of 302 families rated high need, only 143 (47%) were identified by age 4 months. Visiting rates in the first year for those initially rated high need were nearly double those for the remainder, but around two thirds of those with high contact rates/referred to social work were not initially rated high need. Six family characteristics (no income, baby born preterm, multiple pregnancy, South Asian, prior social work/criminal justice involvement, either parent in care as a child) were identified as the commonest/strongest predictors of contact rates; 1003 (83%) families had one such characteristics and/or lived in a highly deprived area, including 228 (93%) of those with high contact rates and 157 (96%) of those referred to social work. Most families at risk will not be identified on an individual basis in the early weeks. Most families in deprived areas need continued input if the most vulnerable families are to be reliably identified.

  1. The LHC Computing Grid in the starting blocks

    CERN Multimedia

    Danielle Amy Venton

    2010-01-01

    As the Large Hadron Collider ramps up operations and breaks world records, it is an exciting time for everyone at CERN. To get the computing perspective, the Bulletin this week caught up with Ian Bird, leader of the Worldwide LHC Computing Grid (WLCG). He is confident that everything is ready for the first data.   The metallic globe illustrating the Worldwide LHC Computing GRID (WLCG) in the CERN Computing Centre. The Worldwide LHC Computing Grid (WLCG) collaboration has been in place since 2001 and for the past several years it has continually run the workloads for the experiments as part of their preparations for LHC data taking. So far, the numerous and massive simulations of the full chain of reconstruction and analysis software could only be carried out using Monte Carlo simulated data. Now, for the first time, the system is starting to work with real data and with many simultaneous users accessing them from all around the world. “During the 2009 large-scale computing challenge (...

  2. FORMATION OF THE PENUMBRA AND START OF THE EVERSHED FLOW

    Energy Technology Data Exchange (ETDEWEB)

    Murabito, M.; Guglielmino, S. L.; Zuccarello, F. [Dipartimento di Fisica e Astronomia—Sezione Astrofisica, Università degli Studi di Catania, Via S. Sofia 78, I-95123 Catania (Italy); Romano, P. [INAF—Osservatorio Astrofisico di Catania, Via S. Sofia 78, I-95123 Catania (Italy); Solanki, S. K., E-mail: mmurabito@oact.inaf.it [Max-Planck-Institut für Sonnensystemforschung Justus-von-Liebig-Weg 3, D-37077 Göttingen (Germany)

    2016-07-01

    We studied the variations of line of sight photospheric plasma flows during the formation phase of the penumbra around a pore in active region NOAA 11490. We used a high spatial, spectral, and temporal resolution data set acquired by the Interferometric BIdimensional Spectrometer operating at the NSO/Dunn Solar Telescope as well as data taken by the Helioseismic and Magnetic Imager on board the Solar Dynamics Observatory satellite ( SDO /HMI). Before the penumbra formed we observed a redshift of the spectral line in the inner part of the annular zone surrounding the pore as well as a blueshift of material associated with opposite magnetic polarity farther away from the pore. We found that the onset of the classical Evershed flow occurs on a very short timescale (1 to 3 hr) while the penumbra is forming. During the same time interval we found changes in the magnetic field inclination in the penumbra, with the vertical field actually changing sign near the penumbral edge, while the total magnetic field showed a significant increase, about 400 G. To explain these and other observations related to the formation of the penumbra and the onset of the Evershed flow we propose a scenario in which the penumbra is formed by magnetic flux dragged down from the canopy surrounding the initial pore. The Evershed flow starts when the sinking magnetic field dips below the solar surface and magnetoconvection sets in.

  3. Scaling CMS data transfer system for LHC start-up

    International Nuclear Information System (INIS)

    Tuura, L; Bockelman, B; Bonacorsi, D; Egeland, R; Feichtinger, D; Metson, S; Rehn, J

    2008-01-01

    The CMS experiment will need to sustain uninterrupted high reliability, high throughput and very diverse data transfer activities as the LHC operations start. PhEDEx, the CMS data transfer system, will be responsible for the full range of the transfer needs of the experiment. Covering the entire spectrum is a demanding task: from the critical high-throughput transfers between CERN and the Tier-1 centres, to high-scale production transfers among the Tier-1 and Tier-2 centres, to managing the 24/7 transfers among all the 170 institutions in CMS and to providing straightforward access to handful of files to individual physicists. In order to produce the system with confirmed capability to meet the objectives, the PhEDEx data transfer system has undergone rigourous development and numerous demanding scale tests. We have sustained production transfers exceeding 1 PB/month for several months and have demonstrated core system capacity several orders of magnitude above expected LHC levels. We describe the level of scalability reached, and how we got there, with focus on the main insights into developing a robust, lock-free and scalable distributed database application, the validation stress test methods we have used, and the development and testing tools we found practically useful

  4. The Starting Point of Hobbes’s Science of Politics

    Directory of Open Access Journals (Sweden)

    Luka Ribarević

    2008-01-01

    Full Text Available As a logical starting point structuring the entire theoretical field of political analysis, Hobbes’s definition of the state of nature is a key for understanding his science of politics. The paper shows that the concept of the state of nature implies two fundamentally distinct types of states in which neither people nor troubles with which they are faced are identical. In the original state of nature conflicts among people stem directly from their nature. Based on the analysis of Hobbes’s understanding of human nature and critical reading of his interpretation of the state of nature by Jean Hampton, the paper identifies the mechanism by which reason and passion turn the state of nature into a state of war. However, alongside the original state of nature, a historical state of nature also coexists, in which conflicts spring from religious views and political beliefs immanent to people as religious and political beings, and as beings of language and conscience. What is crucial for conflicts in this historical state of nature is the influence exerted by language as a discursive context on human action. As the state of war feeds from both human nature and history, any attempt of overcoming the state of nature must abandon them: the state is necessarily an artificial and ahistorical project, based on science of politics as a new political language appropriate for human self-preservation.

  5. CMS Tracker Alignment Performance Results Start-Up 2017

    CERN Document Server

    CMS Collaboration

    2017-01-01

    During the LHC shutdown in Winter 2016/17, the CMS pixel detector, the inner component of the CMS Tracker, was replaced by the Phase-1 upgrade detector. Among others improvements, the new pixel detector consists of four instead of three layers in the central barrel region (BPIX) and three instead of two disks in the endcap regions (FPIX). In this report, performance plots of the first pixel-detector alignment results are presented, which were obtained with cosmic-ray data taken prior to the start of the 2017 LHC pp operation. Alignment constants have been derived using the data collected initially at 0T and later at 3.8T magnetic field to the level of single module positions in the pixel detector, while keeping the alignment parameters of the strip detector fixed at the values determined in the end of 2016. The complete understanding of the alignment and biases was derived by using two algorithms, Millepede-II and HipPy. The results confirm each other.

  6. Start of the big chill for the LHC

    CERN Document Server

    2007-01-01

    The cooling of Sector 7-8 of the LHC, the first to undergo the process, is under way to the 1.9 K necessary for superconductivity. During the night of 14 to 15 March, an important milestone was reached when the entire sector was cooled to 4.5 K, the temperature of liquid helium. The two graphs above show the progression of cooling in Sector 7-8. The first gives the status of the sector on Tuesday 6 March at 4:00 pm, the second on Wednesday 7 March at 10:00 am. Each square represents a magnet.It's the start of the big chill for the LHC. Since the middle of January, the teams from the Accelerator Cryogenics group have been working to cool down the first sector of the machine. Three kilometres of magnets between Point 7 (Ferney-Voltaire) and Point 8 (Prévessin) are to be cooled to 1.9 Kelvin (-271°C), colder than outer space. The first step in the process was to cool the sector to 80 K. Following mechanical and electrical integrity tests at this temperature, it was then further cooled to 20 K for additional e...

  7. A flying start for CERN in H2020

    CERN Multimedia

    EU Projects Office

    2015-01-01

    Following successful participation in a string of some 90 projects within FP7, CERN is also actively involved in Horizon 2020. In 2014, nearly 60 proposals involving CERN’s participation were submitted to various H2020 sub-programmes and the hope is that many more will follow in 2015.   Technological challenges for future detectors, to be addressed by the AIDA-2020 project. The projects coordinated by CERN that have been selected for funding in 2014 span many different fields and activities: science outreach (PopScience), a study of isotopes for medical applications (MEDICIS-PROMED), the development of innovative fibre technologies (INTELUM), international collaboration on accelerator science and technology (E-JADE), novel NMR techniques (BetaDropNMR), new mathematical structures (MathAm) and the procurement of cloud services in Europe (PICSE). After a very encouraging 2014, 2015 started well too: AIDA-2020 and EuroCirCol have recently been selected for funding under the H2020 Rese...

  8. TAX OPTIMIZATION FOR BUSINESS START-UPS IN ROMANIA

    Directory of Open Access Journals (Sweden)

    Maria Zenovia GRIGORE

    2015-07-01

    Full Text Available One of the most important early decisions for an entrepreneur is choosing the optimal form of organization for his business. According to the data provided by the Registry of Commerce, Romanian entrepreneurs usually choose between: Limited Liability Company (LLC and Authorized Natural Person (ANP. LLCs offer liability protection for its owner. This advantage has made the LLC a popular business form for smaller companies, who don't plan to grow the business significantly. Newly set-up companies in Romania are required to apply the micro-companies revenues tax system starting with their first year of operation. For next years, this system is applied only if annual turnover does not exceed EUR 65,000. An individual can pursue an economic activity as an ANP. An advantage of the ANP is the reduced number of tax returns field. In adition, in certain circumstances, an ANP may opt for a very advantageous system of taxation of personal income tax, based on predetermined fixed income. Each one of these entities involves fiscal advantages and disadvantages, which we will try to highlight in this paper.

  9. Peigan Nation to start 101 MW wind farm this month

    International Nuclear Information System (INIS)

    McArthur, D.; Salaff, S.

    1998-01-01

    A joint venture, named Weather-Dancer Wind Power Inc., between Advanced Thermodynamics Corporation (ATC) and the Peigan First Nation Community in Alberta will begin construction in June of a wind farm on its 39,000 hectare reserve. The construction will be progressive, up to a maximum of 101 MW. If and when the farm reaches its full size, it will have cost around $175 million. The wind farm will utilize Nordex Balcke-Duerr (Nordex BD) wind turbines from Denmark. ATC is the sole distributor of these turbines in Canada, and will seek opportunities to market Nordex BD turbines and components throughout Alberta and Western Canada. ATC is also aggressively pursuing opportunities in Quebec and in Atlantic Canada. Financing for the construction of the wind farm and a long-term power purchase and distribution agreement with TransAlta Utilities are as yet incomplete, but negotiations are reported to be progressing well. The Nordex BD N54/1000, rated at one MW, will be the largest turbine, and the Peigan Nation Farm the largest wind farm in North America. This is the second attempt by the Peigan Nation to develop a wind farm on the reserve. On the first attempt, the development failed to secure access to the land needed for the project. This time around, a referendum will be held well in advance of the starting date for construction to obtain majority band approval of the site

  10. Conceptual design of the IFMIF Start-Up monitoring module

    Energy Technology Data Exchange (ETDEWEB)

    Gouat, Philippe, E-mail: philippe.gouat@sckcen.be [SCK-CEN – The Belgian Nuclear Research Centre, Boeretang 200, B-2400 Mol (Belgium); Leysen, Willem; Goussarov, Andrei; Galledou, Papa Sally [SCK-CEN – The Belgian Nuclear Research Centre, Boeretang 200, B-2400 Mol (Belgium); Rapisarda, David; Mota, Fernando; Garcia, Angela [CIEMAT – Centro de Investigaciones Energéticas, Medioambientales y Tecnológicas, Avda. Complutense 40, 28040 Madrid (Spain)

    2013-10-15

    Highlights: ► IFMIF test module conceptual design. ► IFMIF test module foreseen instrumentation. ► Cerenkov photon flux monitor. -- Abstract: The preliminary engineering design of the test facilities, including the various test modules to be used in the IFMIF plant is a part of the IFMIF/EVEDA (Engineering Validation and Engineering Design Activities) project from the Broader Approach to fusion. One presents the current status of the conceptual development of the IFMIF Start-Up Monitoring Module, a dedicated device used in the IFMIF test cell during the commissioning phase of the installation, in order to completely characterise the irradiation conditions behind the target on which the beam of deuterons will be focused. This STUMM embarks a lot of instrumentation to precisely characterise the neutron field, the nuclear heating and the temperatures in the test cell. One briefly describes the measuring instruments (including a specific radiation flux monitor under development), the possible layouts and the possible positioning. One also defines which types of measurements are expected by this especially dedicated commissioning module.

  11. A prompt start: Implementing the framework convention on climate change

    International Nuclear Information System (INIS)

    Chayes, A.; Skolnikoff, E.B.; Victor, D.G.

    1992-01-01

    A Framework Convention on Climate Change is under active negotiation in the United Nations with the expectation it will be ready for Signature at the Rio Conference this June. Under the most optimistic projections, a Convention will not come into force and be an effective instrument for months, probably years. In recognition of the several institutional tasks that will be of crucial importance whatever the detailed content of the Convention a small group of high international organizations involved in the negotiations was convened at the Rockefeller Foundation's Conference Center at Bellagio in January. The discussions at Bellagio on the need for a Prompt Start on these institutional tasks benefitted from earlier meetings at Harvard in March and at Bermuda in May, 1991, that the co-organizers convened to discuss these and related aspects of the negotiations on a Climate Convention. Those meetings were attended by members of the academic community, officials from the United Nations, and representatives of governments involved in the negotiations

  12. Design and Operation of the Transformed National Healthy Start Evaluation.

    Science.gov (United States)

    Banks, Jamelle E; Dwyer, Maura; Hirai, Ashley; Ghandour, Reem M; Atrash, Hani K

    2017-12-01

    Purpose Improving pregnancy outcomes for women and children is one of the nation's top priorities. The Healthy Start (HS) program was created to address factors that contribute to high infant mortality rates (IMRs) and persistent disparities in IMRs. The program began in 1991 and was transformed in 2014 to apply lessons from emerging research, past evaluation findings, and expert recommendations. To understand the implementation and impact of the transformed program, there is a need for a robust and comprehensive evaluation. Description The national HS evaluation will include an implementation evaluation, which will describe program components that affect outcomes; a utilization evaluation, which will examine the characteristics of women and infants who did and did not utilize the program; and an outcome evaluation, which will assess the program's effectiveness with regard to producing expected outcomes among the target population. Data sources include the National HS Program Survey, a HS participant survey, and individual-level program data linked to vital records and the Pregnancy Risk Assessment Monitoring System (PRAMS) survey. Assessment Descriptive analyses will be used to examine differences in risk profiles between participants and non-participants, as well as to calculate penetration rates for high-risk women in respective service areas. Multivariable analyses will be used to determine the impact of the program on key outcomes and will explore variation by dose, type of services received, and grantee characteristics. Conclusion Evaluation findings are expected to inform program decisions and direction, including identification of effective program components that can be spread and scaled.

  13. Start a Research on Biopolymer Polyhydroxyalkanoate (PHA: A Review

    Directory of Open Access Journals (Sweden)

    Giin-Yu Amy Tan

    2014-03-01

    Full Text Available With the impending fossil fuel crisis, the search for and development of alternative chemical/material substitutes is pivotal in reducing mankind’s dependency on fossil resources. One of the potential substitute candidates is polyhydroxyalkanoate (PHA. PHA is a carbon-neutral and valuable polymer that could be produced from many renewable carbon sources by microorganisms, making it a sustainable and environmental-friendly material. At present, PHA is not cost competitive compared to fossil-derived products. Encouraging and intensifying research work on PHA is anticipated to enhance its economic viability in the future. The development of various biomolecular and chemical techniques for PHA analysis has led to the identification of many PHA-producing microbial strains, some of which are deposited in culture collections. Research work on PHA could be rapidly initiated with these ready-to-use techniques and microbial strains. This review aims to facilitate the start-up of PHA research by providing a summary of commercially available PHA-accumulating microbial cultures, PHA biosynthetic pathways, and methods for PHA detection, extraction and analysis.

  14. [The anatomists who started anthropology in Turkey and their contributions].

    Science.gov (United States)

    Uluçam, E; Gökçe, N; Başağaoğlu, J

    2002-01-01

    The Turkish Institute of Antropology was estabilished in 1925 as a unit of the Medical School of Istanbul University (Darülfünun), named the Antropology Research Center (Antropoloji Tetkikat Merkezi). It was a part of the medical faculty until 1932. After the university reform it was connected to the School of Science and in late 1935 it was transfered to the School of Languages History and Geography (Dil Tarih Coğrafya Fakültesi) in Ankara. The center started to publish "The Journal of Turkish Anthropology" with Dr. Nuretttin Ali Berkols researches in 1925. It was published in two languages, Turkish and French. The faculty members of the institute, Dr. Mouchet, Dr. Süreyya Ali and Dr. Ismail Hakki formed the editorial board of the journal. We see that from the first issue of the journal in 1925 until the special issue prepared for the XVIII. Anthropology and Prehistorical Archealogy Congress in 1939, Dr. Nurettin Ali Berkol and Dr. Mouchet were members of the administrative committee of the journal. In this article; we studied the contributions of the anatomists to the development of anthropology in Turkey.

  15. Benchmarking of radiological departments. Starting point for successful process optimization

    International Nuclear Information System (INIS)

    Busch, Hans-Peter

    2010-01-01

    Continuous optimization of the process of organization and medical treatment is part of the successful management of radiological departments. The focus of this optimization can be cost units such as CT and MRI or the radiological parts of total patient treatment. Key performance indicators for process optimization are cost- effectiveness, service quality and quality of medical treatment. The potential for improvements can be seen by comparison (benchmark) with other hospitals and radiological departments. Clear definitions of key data and criteria are absolutely necessary for comparability. There is currently little information in the literature regarding the methodology and application of benchmarks especially from the perspective of radiological departments and case-based lump sums, even though benchmarking has frequently been applied to radiological departments by hospital management. The aim of this article is to describe and discuss systematic benchmarking as an effective starting point for successful process optimization. This includes the description of the methodology, recommendation of key parameters and discussion of the potential for cost-effectiveness analysis. The main focus of this article is cost-effectiveness (efficiency and effectiveness) with respect to cost units and treatment processes. (orig.)

  16. Low levels of extraneous agents in vaccine starting materials.

    Science.gov (United States)

    Rouby, Jean-Claude

    2010-05-01

    There are different ways to define the concept of 'low levels' of extraneous agents in vaccines and vaccine starting materials, based on the amount of extraneous agents as such, the sensitivity of the detection method and the probability approach linked to the sampling method. None of these approaches, however, is entirely satisfactory--a general definition of a 'low level' cannot be provided. Since the main point is the safety of medicinal products, the risk analysis approach to 'low level' contaminations can be considered as a way to overcome the above mentioned deadlock. But as too many variables impact the risk analysis, it cannot be properly performed either. In practice, seeds are tested to show freedom from extraneous agents, the other raw materials are inactivated through a validated method. However, there are technical and regulatory limits in both cases, and neither testing nor inactivation entirely guarantees freedom from extraneous agents. Despite this unsatisfactory situation, it should be acknowledged that no truly significant disease outbreak linked to an extraneous agent has been identified until today. Regulatory actions are mainly undertaken when a sanitary problem occurs. In the end, companies remain responsible for their products. 2010 The International Association for Biologicals. Published by Elsevier Ltd. All rights reserved.

  17. SEASTAR: systematic evaluation of alternative transcription start sites in RNA.

    Science.gov (United States)

    Qin, Zhiyi; Stoilov, Peter; Zhang, Xuegong; Xing, Yi

    2018-05-04

    Alternative first exons diversify the transcriptomes of eukaryotes by producing variants of the 5' Untranslated Regions (5'UTRs) and N-terminal coding sequences. Accurate transcriptome-wide detection of alternative first exons typically requires specialized experimental approaches that are designed to identify the 5' ends of transcripts. We developed a computational pipeline SEASTAR that identifies first exons from RNA-seq data alone then quantifies and compares alternative first exon usage across multiple biological conditions. The exons inferred by SEASTAR coincide with transcription start sites identified directly by CAGE experiments and bear epigenetic hallmarks of active promoters. To determine if differential usage of alternative first exons can yield insights into the mechanism controlling gene expression, we applied SEASTAR to an RNA-seq dataset that tracked the reprogramming of mouse fibroblasts into induced pluripotent stem cells. We observed dynamic temporal changes in the usage of alternative first exons, along with correlated changes in transcription factor expression. Using a combined sequence motif and gene set enrichment analysis we identified N-Myc as a regulator of alternative first exon usage in the pluripotent state. Our results demonstrate that SEASTAR can leverage the available RNA-seq data to gain insights into the control of gene expression and alternative transcript variation in eukaryotic transcriptomes.

  18. Start of the construction of initial advanced BWRs

    International Nuclear Information System (INIS)

    Yamada, Yasuo; Furukawa, Hideyasu; Yoshida, Tomiharu

    1992-01-01

    The construction of first advanced BWRs (ABWR), No. 6 and No. 7 plants in Kashiwazaki Kariwa Nuclear Power Station, Tokyo Electric Power Co., Inc., was started, and the commercial operation is scheduled to begin in 1996 and 1997. The ABWR with the unit capacity of 1356 MW which is the largest class in the world has been developed aiming at the further improvement of safety, operation performance, economical efficiency and so on. Hitachi Limited carried out the detailed review on new parts design and expected the perfection so as to make the first machine into the plant maintaining high reliability. The course of development of the ABWR, the outline of No. 6 and No. 7 plants in Kashiwazaki Kariwa Nuclear Power Station, the review of the design of new parts, the establishment of the technology of manufacturing RCCVs, the verification of the maintenance and checkup of internal pumps and improved type control rod driving mechanism and so on are reported. The ABWR is Japanese third improved type standard plant, but also it is expected to be adopted worldwide. (K.I.)

  19. Doctoral Dissertations in the Internet: A Good Start in Finland

    Directory of Open Access Journals (Sweden)

    Esko Häkli

    2000-05-01

    Full Text Available At the present stage of the IT-applications the change from print publishing into electronic publishing of doctoral dissertations is not only a question of technology but it is also, and possibly even to a greater extent, a question of thinking. Although there is a large selection of technologies and publication formats available, none of them seem to be mature enough to be a self-evident choice. But obviously a greater obstacle can be found in the minds of people. In many cases legal regulations also have to be revised. Academic traditions still prefer properly printed dissertations and the attitudes of the academic community are not necessarily favourable towards electronic publishing in general. Young post-graduate students are obviously not able to appreciate a virtual dissertation. They seem to need a real tangible thing, which they also can show to their parents! And finally, the whole organization and financing of publishing may need to be revised, an exercise which is far more difficult than only starting to use new technology.

  20. Gas Turbine Engine Starting Applicated on TV2-117 Turboshaft

    Directory of Open Access Journals (Sweden)

    R. M. Catana

    2017-10-01

    Full Text Available The paper presents the examination of two different types of engine starting configurations, applicated on TV2-117A turboshaft, running into the test bench. The first type of starting configuration is a normal starting, with the engine connected to the dynamometer which controls the free turbine speed by the dynamometer load. The second type of starting is a different one, the engine is not connected with the dynamometer, therefore it results that there is no control of the free turbine speed from the dynamometer, only from the engine but in particular conditions. To achieve the starting phase an instrumentation scheme is created, to control and monitor the engine, and a starting sequence with all the parameters, confirmations and commands that are involved into the starting phase. The engine starting is performed by the test bench operating system, composed of an acquisition system and a programmable controller, wherewith is running the starting sequence.

  1. A method for starting up the gas isolating section of a benzine pyrolysis installation

    Energy Technology Data Exchange (ETDEWEB)

    Bruskin, Yu.A.; Gorokhov, V.V.; Kotler, L.D.; Shevchenko, K.N.; Zeldin, V.Ye.

    1982-01-01

    In the method for starting up a gas isolation section of a benzine pyrolysis unit, which includes starting the demethanizer in a steaming mode, starting the ethane and ethylene and propane and propylene towers, filling the ethylene cooling system with a hydrocarbon fraction, starting the ethylene cooling system, switching to a mode of the demethanization unit, starting the subassemblies for hydration and isolation of the ethylene and propylene fractions, in order to reduce the length of the start up period and to reduce the ejection of gas to the burner, after starting the demethanizer in the steaming mode, starting the ethane and ethylene and propane and propylene towers, the ethane and ethylene and propane and propylene fractions are mixed before the hydration subassemblies with an H2 bearing gas for catalytic reforming and then the other units and subassemblies are started.

  2. Gendered career considerations consolidate from the start of medical education.

    Science.gov (United States)

    Alers, Margret; Verdonk, Petra; Bor, Hans; Hamberg, Katarina; Lagro-Janssen, Antoine

    2014-09-13

    To explore changes in specialty preferences and work-related topics during the theoretical phase of Dutch medical education and the role of gender. A cohort of medical students at Radboudumc, the Netherlands, was surveyed at start (N=612, 69.1% female) and after three years (N=519, 69.2% female), on specialty preferences, full-time or part-time work, motivational factors, and work-life issues. Chi square tests were performed to analyze gender-differences, and logistic regression to explore the influence of gender on considerations. A total of 214 female and 78 male students completed both surveys. After three years, the male students remained highly interested in surgery, but the female students increasingly preferred gynecology. These initial preferences were predictive. Four out of five male students versus three out of five female students continued to show a full-time preference. Women increasingly preferred part-time work. After three years, the combination of work, care, and patient contact motivated female students more, whereas salary remained more important to male students. Female students indicated that their future careers would influence their family life; male students assumed having a family would only affect their partners' careers. Against an international background of the feminization of medicine, our study shows that career considerations are reinforced early in medical studies. Women prefer to work fewer hours and anticipate care tasks more often. Students' preferences reflect Dutch cultural norms about working men and women. Therefore, guidance in choice-making much earlier in medical education can create opportunities.

  3. It Starts with a Hashtag… the #365scienceselfies Project

    Science.gov (United States)

    Guertin, L. A.

    2016-12-01

    The year 2016 is the year of #365scienceselfies. The idea was initially proposed on Twitter for scientists to take one selfie a day to chronicle our everyday lives. The overarching goals include expanding the public perception of who scientists are (gender, race, physical appearance, etc.) and what scientists do outside of science (hobbies, raise a family, etc.). Because the selfie culture is popular among women, the project is hoping to showcase women scientists in a positive forum. Starting January 1, 2016, graduate students, post-doctoral researchers, and faculty members began posting selfies on Twitter and Instagram with the hashtag #365scienceselfies. Some photos are being posted with a frequency of close to once a day, while others are posting selfies once a week or on an occasional basis. Photos continue to appear online of scientists doing fieldwork, lab work, computer work, exercising, eating, socializing, and more. My motivation for participating in the #365scienceselfies project is to teach others, specifically the K-12 teachers and students I work with that struggle to understand the field of Earth science overall, about my life as a female geoscience academic. Little did I realize how much I would learn about myself and my own life. For example, there have been many, many days where I struggled to find something to take a photo of that does not involve my computer screen. Participating in the project was effective in sparking conversations and questions among my own communities and networks, especially the non-scientists that I included in daily photos (my hairdresser, Zumba instructors, etc.). The remaining challenge will be to synthesize this year of selfies (I have been doing so on a blog http://sites.psu.edu/365scienceselfies/) and to engage an even broader community in exploration and discussion of selfies, and what we can learn about the life of a geoscientist, one photo at a time.

  4. How Very Massive Metal-Free Stars Start Cosmological Reionization

    Science.gov (United States)

    Wise, John H.; Abel, Tom

    2008-01-01

    The initial conditions and relevant physics for the formation of the earliest galaxies are well specified in the concordance cosmology. Using ab initio cosmological Eulerian adaptive mesh refinement radiation hydrodynamical calculations, we discuss how very massive stars start the process of cosmological reionization. The models include nonequilibrium primordial gas chemistry and cooling processes and accurate radiation transport in the case B approximation using adaptively ray-traced photon packages, retaining the time derivative in the transport equation. Supernova feedback is modeled by thermal explosions triggered at parsec scales. All calculations resolve the local Jeans length by at least 16 grid cells at all times and as such cover a spatial dynamic range of approx.10(exp 6). These first sources of reionization are highly intermittent and anisotropic and first photoionize the small-scale voids surrounding the halos they form in, rather than the dense filaments they are embedded in. As the merging objects form larger, dwarf-sized galaxies, the escape fraction of UV radiation decreases and the H II regions only break out on some sides of the galaxies, making them even more anisotropic. In three cases, SN blast waves induce star formation in overdense regions that were formed earlier from ionization front instabilities. These stars form tens of parsecs away from the center of their parent DM halo. Approximately five ionizing photons are needed per sustained ionization when star formation in 10(exp 6) stellar Mass halos is dominant in the calculation. As the halos become larger than approx.10(exp 7) Stellar Mass, the ionizing photon escape fraction decreases, which in turn increases the number of photons per ionization to 15-50, in calculations with stellar feedback only. Radiative feedback decreases clumping factors by 25% when compared to simulations without star formation and increases the average temperature of ionized gas to values between 3000 and 10,000 K.

  5. STARTING POINT FOR BRANDING SLAVONIA AS A TOURIST DESTINATION

    Directory of Open Access Journals (Sweden)

    Berislav Bolfek

    2012-12-01

    future as a starting point in the definition and development of the branding project of Slavonia as a tourist destination.

  6. Reactor decommissioning strategy: a new start for BNFL

    International Nuclear Information System (INIS)

    Woollam, P.; Nurden, P.

    2001-01-01

    The key points of BNFL Magnox Electric's revised waste management and reactor decommissioning strategy for the reactor sites are enlisted. Reactors will be defuelled as soon as practicable after shutdown. Predominantly Caesium contaminated plant will be dismantled when it is no longer needed. Cobalt contaminated plant such as boilers will remain in position until the reactors are dismantled, but appropriate decontamination technology will be regularly reviewed. All buildings except the reactor buildings will be dismantled as soon as practicable after they are no longer needed. Operational ILW, except some activated components, will be retrieved and packaged during the Care and Maintenance preparation period. All wastes will be stored on site, and handled in the long term in accordance with Government policy. Reactor buildings and their residual contents will be placed in a passive safe storage Care and Maintenance condition in a manner appropriate for the site. Contaminated land will be managed to maintain public safety. The reactors will be finally dismantled in a sequenced programme with a start date and duration to be decided at the appropriate time in the light of circumstances prevalent at that time. Currently, the Company is considering a sequenced programme across all sites, notionally beginning around 100 years from station shutdown, leading to a range of deferral periods. For provisioning purposes, the Company has costed a strategy involving reactor dismantling deferrals ranging from 85 to about 105 years in order to demonstrate prudent provisioning to meet its liabilities. A risk provision to reflect the potential for shorter deferral periods is included in the cost estimates. The end point for reactor decommissioning is site clearance and delicensing, based on the assumption that a reasonably practicable interpretation of the 'no danger' clause in the Nuclear Installations Act 1965 (as amended) can be developed. In line with Government policy, and taking

  7. Understanding start-up problems in yeast glycolysis.

    Science.gov (United States)

    Overal, Gosse B; Teusink, Bas; Bruggeman, Frank J; Hulshof, Josephus; Planqué, Robert

    2018-05-01

    Yeast glycolysis has been the focus of research for decades, yet a number of dynamical aspects of yeast glycolysis remain poorly understood at present. If nutrients are scarce, yeast will provide its catabolic and energetic needs with other pathways, but the enzymes catalysing upper glycolytic fluxes are still expressed. We conjecture that this overexpression facilitates the rapid transition to glycolysis in case of a sudden increase in nutrient concentration. However, if starved yeast is presented with abundant glucose, it can enter into an imbalanced state where glycolytic intermediates keep accumulating, leading to arrested growth and cell death. The bistability between regularly functioning and imbalanced phenotypes has been shown to depend on redox balance. We shed new light on these phenomena with a mathematical analysis of an ordinary differential equation model, including NADH to account for the redox balance. In order to gain qualitative insight, most of the analysis is parameter-free, i.e., without assigning a numerical value to any of the parameters. The model has a subtle bifurcation at the switch between an inviable equilibrium state and stable flux through glycolysis. This switch occurs if the ratio between the flux through upper glycolysis and ATP consumption rate of the cell exceeds a fixed threshold. If the enzymes of upper glycolysis would be barely expressed, our model predicts that there will be no glycolytic flux, even if external glucose would be at growth-permissable levels. The existence of the imbalanced state can be found for certain parameter conditions independent of the mentioned bifurcation. The parameter-free analysis proved too complex to directly gain insight into the imbalanced states, but the starting point of a branch of imbalanced states can be shown to exist in detail. Moreover, the analysis offers the key ingredients necessary for successful numerical continuation, which highlight the existence of this bistability and the

  8. Systematic analysis of transcription start sites in avian development.

    Directory of Open Access Journals (Sweden)

    Marina Lizio

    2017-09-01

    Full Text Available Cap Analysis of Gene Expression (CAGE in combination with single-molecule sequencing technology allows precision mapping of transcription start sites (TSSs and genome-wide capture of promoter activities in differentiated and steady state cell populations. Much less is known about whether TSS profiling can characterize diverse and non-steady state cell populations, such as the approximately 400 transitory and heterogeneous cell types that arise during ontogeny of vertebrate animals. To gain such insight, we used the chick model and performed CAGE-based TSS analysis on embryonic samples covering the full 3-week developmental period. In total, 31,863 robust TSS peaks (>1 tag per million [TPM] were mapped to the latest chicken genome assembly, of which 34% to 46% were active in any given developmental stage. ZENBU, a web-based, open-source platform, was used for interactive data exploration. TSSs of genes critical for lineage differentiation could be precisely mapped and their activities tracked throughout development, suggesting that non-steady state and heterogeneous cell populations are amenable to CAGE-based transcriptional analysis. Our study also uncovered a large set of extremely stable housekeeping TSSs and many novel stage-specific ones. We furthermore demonstrated that TSS mapping could expedite motif-based promoter analysis for regulatory modules associated with stage-specific and housekeeping genes. Finally, using Brachyury as an example, we provide evidence that precise TSS mapping in combination with Clustered Regularly Interspaced Short Palindromic Repeat (CRISPR-on technology enables us, for the first time, to efficiently target endogenous avian genes for transcriptional activation. Taken together, our results represent the first report of genome-wide TSS mapping in birds and the first systematic developmental TSS analysis in any amniote species (birds and mammals. By facilitating promoter-based molecular analysis and genetic

  9. Starting them Early: Incorporating Communication Training into Undergraduate Research Internships

    Science.gov (United States)

    Bartel, B. A.; Morris, A. R.; Charlevoix, D.

    2014-12-01

    In order to truly broaden the impact of our scientific community, effective communication should be taught alongside research skills to developing scientists. In the summer of 2014, we incorporated an informal communications course into the 10th year of UNAVCO's Research Experiences in Solid Earth Science for Students (RESESS), a year-long internship program centered around an 11-week intensive summer research experience. The goals of the newly designed course included giving students the tools they need to make a broader impact with their science, starting now; improving the students' confidence in public speaking and using social media for outreach; and giving students the tools they need to apply for jobs or graduate school. Specifically, the course included teaching of professional communication skills, such as e-mail and phone etiquette, resume and CV tailoring, and interview techniques, and public communications skills, such as crafting and simplifying messages, visual communication for the public, and public speaking. Student interns were encouraged to step back from the details of their research projects to put their work into a big-picture context relevant to the public and to policy makers. The course benefited from input and/or participation from UNAVCO Education and Community Engagement staff, engineering and managerial staff, and graduate student interns outside the RESESS program, and University of Colorado research and communications mentors already involved in RESESS. As the summer program is already packed with research and skill development, one major challenge was fitting in teaching these communications skills amongst many other obligations: a GRE course, a peer-focused scientific communications course, a computing course, and, of course, research. Can we do it all? This presentation will provide an overview of the course planning, articulation of course goals, and execution challenges and successes. We will present our lessons learned from

  10. Start/End Delays of Voiced and Unvoiced Speech Signals

    Energy Technology Data Exchange (ETDEWEB)

    Herrnstein, A

    1999-09-24

    Recent experiments using low power EM-radar like sensors (e.g, GEMs) have demonstrated a new method for measuring vocal fold activity and the onset times of voiced speech, as vocal fold contact begins to take place. Similarly the end time of a voiced speech segment can be measured. Secondly it appears that in most normal uses of American English speech, unvoiced-speech segments directly precede or directly follow voiced-speech segments. For many applications, it is useful to know typical duration times of these unvoiced speech segments. A corpus, assembled earlier of spoken ''Timit'' words, phrases, and sentences and recorded using simultaneously measured acoustic and EM-sensor glottal signals, from 16 male speakers, was used for this study. By inspecting the onset (or end) of unvoiced speech, using the acoustic signal, and the onset (or end) of voiced speech using the EM sensor signal, the average duration times for unvoiced segments preceding onset of vocalization were found to be 300ms, and for following segments, 500ms. An unvoiced speech period is then defined in time, first by using the onset of the EM-sensed glottal signal, as the onset-time marker for the voiced speech segment and end marker for the unvoiced segment. Then, by subtracting 300ms from the onset time mark of voicing, the unvoiced speech segment start time is found. Similarly, the times for a following unvoiced speech segment can be found. While data of this nature have proven to be useful for work in our laboratory, a great deal of additional work remains to validate such data for use with general populations of users. These procedures have been useful for applying optimal processing algorithms over time segments of unvoiced, voiced, and non-speech acoustic signals. For example, these data appear to be of use in speaker validation, in vocoding, and in denoising algorithms.

  11. How Very Massive Metal Free Stars Start Cosmological Reionization

    International Nuclear Information System (INIS)

    Wise, John H.; Abel, Tom

    2007-01-01

    The initial conditions and relevant physics for the formation of the earliest galaxies are well specified in the concordance cosmology. Using ab initio cosmological Eulerian adaptive mesh refinement radiation hydrodynamical calculations, we discuss how very massive stars start the process of cosmological reionization. The models include non-equilibrium primordial gas chemistry and cooling processes and accurate radiation transport in the Case B approximation using adaptively ray traced photon packages, retaining the time derivative in the transport equation. Supernova feedback is modeled by thermal explosions triggered at parsec scales. All calculations resolve the local Jeans length by at least 16 grid cells at all times and as such cover a spatial dynamic range of ∼10 6 . These first sources of reionization are highly intermittent and anisotropic and first photoionize the small scales voids surrounding the halos they form in, rather than the dense filaments they are embedded in. As the merging objects form larger, dwarf sized galaxies, the escape fraction of UV radiation decreases and the H II regions only break out on some sides of the galaxies making them even more anisotropic. In three cases, SN blast waves induce star formation in overdense regions that were formed earlier from ionization front instabilities. These stars form tens of parsecs away from the center of their parent DM halo. Approximately 5 ionizing photons are needed per sustained ionization when star formation in 10 6 M · halos are dominant in the calculation. As the halos become larger than ∼10 7 M # circle d ot#, the ionizing photon escape fraction decreases, which in turn increases the number of photons per ionization to 15--50, in calculations with stellar feedback only. Supernova feedback in these more massive halos creates a more diffuse medium, allowing the stellar radiation to escape more easily and maintaining the ratio of 5 ionizing photons per sustained ionization

  12. Parental Book Reading and Social-Emotional Outcomes for Head Start Children in Foster Care.

    Science.gov (United States)

    Lee, Kyunghee; Lee, Jung-Sook

    2016-01-01

    This study examines the associations between parental book reading and social-emotional outcomes for Head Start children in foster care. Despite no main Head Start impact on parental book reading, subgroup effects were found. Foster parents in Head Start provided more book reading for children with disabilities but less for children with low preacademic scores. Head Start enhanced social-emotional outcomes for children in foster care. The positive impacts of Head Start on children's social-emotional outcomes were greater when parents read books frequently. Head Start should include more foster families and provided parenting skills to enhance social-emotional outcomes for children in foster care.

  13. The later investment starts, the more expensive it will be

    International Nuclear Information System (INIS)

    Marcan, P.; Slovak, K.

    2007-01-01

    In this paper the interview with Martin Roman, Chairman of the Board of Directors of the Czech Energy Group, CEZ is published. Most important parts of this interview is there presented. M. Roman considers windmills and other renewable energy sources are viable, but they will not save the energy sector. According to the director of one of the largest Central European companies, concerns about a shortage of electricity are unreasonable. Nevertheless, the later the investment starts, the more expensive it will be. CEZ continues to look to the Balkans and Russia, but in addition to a power plant to be built in cooperation with Slovnaft, it can also see room for investment in Slovakia? You are preparing the upgrading? of your coal burning plants in the Czech Republic. In terms of emissions, coal is the worst alternative. Do you expect the cancellation of the EU emissions trading scheme after 2012? We believe that emissions trading will also exist after 2012. The scheme may be even stricter that today. We believe that in the future it may be even more finance-consuming for the companies. We have the advantage that the power plants being upgraded are located directly at the source of high quality black coal. The calculations are satisfactory and therefore it will be profitable for us. Wouldn't gas be a cleaner and cheaper alternative? We deal with gas as well, but coal came first as it is simpler for us. The power plants already exist and we don't need any extra permission. To put it simply, it is easier to renew an existing power plant than to build a completely new one? Is the strict attitude of the Slovak government towards Slovenske elektrarne helpful to you and other competitors? Certainly, each government exerts tough pressure on the company that controls the major part of the market? CEZ is a similar giant that even controls the distribution? But in the Czech Republic we do not have such a share of production as Slovenske elektrarne in Slovakia

  14. Engine-start Control Strategy of P2 Parallel Hybrid Electric Vehicle

    Science.gov (United States)

    Xiangyang, Xu; Siqi, Zhao; Peng, Dong

    2017-12-01

    A smooth and fast engine-start process is important to parallel hybrid electric vehicles with an electric motor mounted in front of the transmission. However, there are some challenges during the engine-start control. Firstly, the electric motor must simultaneously provide a stable driving torque to ensure the drivability and a compensative torque to drag the engine before ignition. Secondly, engine-start time is a trade-off control objective because both fast start and smooth start have to be considered. To solve these problems, this paper first analyzed the resistance of the engine start process, and established a physic model in MATLAB/Simulink. Then a model-based coordinated control strategy among engine, motor and clutch was developed. Two basic control strategy during fast start and smooth start process were studied. Simulation results showed that the control objectives were realized by applying given control strategies, which can meet different requirement from the driver.

  15. The starting dose of levothyroxine in primary hypothyroidism treatment: a prospective, randomized, double-blind trial

    NARCIS (Netherlands)

    Roos, Annemieke; Linn-Rasker, Suzanne P.; van Domburg, Ron T.; Tijssen, Jan P.; Berghout, Arie

    2005-01-01

    BACKGROUND: The treatment of hypothyroidism with levothyroxine is effective and simple; however, recommendations for the starting dose vary considerably. To our knowledge, the levothyroxine starting dose has never been studied prospectively. METHODS: We conducted a prospective, randomized,

  16. Start-up and commercial operation of the Laguna Verde power plants, unit 1

    International Nuclear Information System (INIS)

    Torres R, J.F.

    1991-01-01

    The main features of the unit 1 of the Laguna Verde Power Plant is presented as well as the phases of the start-up process. The process includes various steps and tests up to start the commercial operation. (author)

  17. Access and Diversity in the Running Start Program: A Comparison of Washington's Running Start Program to Other State Level Dual Enrollment Programs Hosted on a College Campus

    Science.gov (United States)

    Smith, Karl

    2014-01-01

    Since 1990, high school students in Washington have had the choice of earning college credit through the Running Start program. Running start is a dual enrollment and dual credit program that allows eleventh and twelfth grade high school students to take college courses at any of Washington's 34 community and technical colleges, Central Washington…

  18. Quantifying Variation in Head Start Effects on Young Children's Cognitive and Socio-Emotional Skills Using Data from the National Head Start Impact Study

    Science.gov (United States)

    Bloom, Howard S.; Weiland, Christina

    2015-01-01

    This paper uses data from the Head Start Impact Study (HSIS), a nationally representative multisite randomized trial, to quantify variation in effects of Head Start during 2002-2003 on children's cognitive and socio-emotional outcomes relative to the effects of other local alternatives, including parent care. We find that (1) treatment and control…

  19. Supporting Optimal Child Development through Early Head Start and Head Start Programs: Reflections on Secondary Data Analyses of FACES and EHSREP

    Science.gov (United States)

    Chazan-Cohen, Rachel; Halle, Tamara G.; Barton, Lauren R.; Winsler, Adam

    2012-01-01

    We are delighted to reflect on the 10 papers highlighted in this important special issue of "Early Childhood Research Quarterly" devoted to recent secondary data analyses of the FACES and EHSREP datasets. First, we provide some background on Head Start research and give an overview of the large-scale Head Start and Early Head Start…

  20. The Impact of Head Start on Children, Families and Communities. Final Report of the Head Start Evaluation, Synthesis and Utilization Project. Executive Summary.

    Science.gov (United States)

    McKey, Ruth Hubbell; And Others

    This report summarizes the results of a study on the impact of Head Start on children's cognitive and socioemotional development, on child health and health institutions in the community, on enrollees' families, and on communities where Head Start programs operate. After discussing the background and methodology of the study, the report concludes…