A laser printing based approach for printed electronics

Energy Technology Data Exchange (ETDEWEB)

Zhang, T.; Hu, M.; Guo, Q.; Zhang, W.; Yang, J., E-mail: jyang@eng.uwo.ca [Department of Mechanical and Materials Engineering, Western University, London N6A 3K7 (Canada); Liu, Y.; Lau, W. [Chengdu Green Energy and Green Manufacturing Technology R& D Center, 355 Tengfei Road, 620107 Chengdu (China); Wang, X. [Department of Mechanical and Materials Engineering, Western University, London N6A 3K7 (Canada); Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)

2016-03-07

Here we report a study of printing of electronics using an office use laser printer. The proposed method eliminates those critical disadvantages of solvent-based printing techniques by taking the advantages of electroless deposition and laser printing. The synthesized toner acts as a catalyst for the electroless copper deposition as well as an adhesion-promoting buffer layer between the substrate and deposited copper. The easy metallization of printed patterns and strong metal-substrate adhesion make it an especially effective method for massive production of flexible printed circuits. The proposed process is a high throughput, low cost, efficient, and environmentally benign method for flexible electronics manufacturing.

A laser printing based approach for printed electronics

International Nuclear Information System (INIS)

Zhang, T.; Hu, M.; Guo, Q.; Zhang, W.; Yang, J.; Liu, Y.; Lau, W.; Wang, X.

2016-01-01

Here we report a study of printing of electronics using an office use laser printer. The proposed method eliminates those critical disadvantages of solvent-based printing techniques by taking the advantages of electroless deposition and laser printing. The synthesized toner acts as a catalyst for the electroless copper deposition as well as an adhesion-promoting buffer layer between the substrate and deposited copper. The easy metallization of printed patterns and strong metal-substrate adhesion make it an especially effective method for massive production of flexible printed circuits. The proposed process is a high throughput, low cost, efficient, and environmentally benign method for flexible electronics manufacturing.

Comparing the characteristics of highly cited titles and highly alted titles

Energy Technology Data Exchange (ETDEWEB)

Didegah, F.; Bowman, T.D.; Bowman, S.; Hartley, J.

2016-07-01

This study examines differences in the types of titles for articles that show high altmetric activity (highly alted articles) versus highly cited articles. This work expands on previous research on document titles in combination with a grounded theory approach to develop a codebook in which articles were manually coded based on 11 characteristics. The results show that there are differences and similarities in titles across many of the examined characteristics; highly cited titles and highly mentioned titles on Wikipedia have some similar characteristics such as they have the the highest percentage of substantive words; in addition, there are no or very few titles referencing outside or with humor/lightness on both platforms. Twitter and Facebook also showed some similarities having the highest percentage of humorous/light titles and lowest percentage of substantive words in their titles. (Author)

The best printing methods to print satellite images

Directory of Open Access Journals (Sweden)

G.A. Yousif

2011-12-01

In this paper different printing systems were used to print an image of SPOT-4 satellite, caver part of Sharm Elshekh area, Sinai, Egypt, on the same type of paper as much as possible, especially in the photography. This step is followed by measuring the experimental data, and analyzed colors to determine the best printing systems for satellite image printing data. The laser system is the more printing system where produce a wider range of color and highest densities of ink and access much color detail. Followed by the offset system which it recorded the best dot gain. Moreover, the study shows that it can use the advantages of each method according to the satellite image color and quantity to be produced.

Digital printing

Science.gov (United States)

Sobotka, Werner K.

1997-02-01

Digital printing is described as a tool to replace conventional printing machines completely. Still this goal was not reached until now with any of the digital printing technologies to be described in the paper. Productivity and costs are still the main parameters and are not really solved until now. Quality in digital printing is no problem anymore. Definition of digital printing is to transfer digital datas directly on the paper surface. This step can be carried out directly or with the use of an intermediate image carrier. Keywords in digital printing are: computer- to-press; erasable image carrier; image carrier with memory. Digital printing is also the logical development of the new digital area as it is pointed out in Nicholas Negropotes book 'Being Digital' and also the answer to networking and Internet technologies. Creating images text and color in one country and publishing the datas in another country or continent is the main advantage. Printing on demand another big advantage and last but not least personalization the last big advantage. Costs and being able to coop with this new world of prepress technology is the biggest disadvantage. Therefore the very optimistic growth rates for the next few years are really nonexistent. The development of complete new markets is too slow and the replacing of old markets is too small.

Potential Cost Savings for Use of 3D Printing Combined With 3D Imaging and CPLM for Fleet Maintenance and Revitalization

Science.gov (United States)

2014-04-30

bäÉîÉåíÜ=^ååì~ä=^Åèìáëáíáçå= oÉëÉ~êÅÜ=póãéçëáìã= qÜìêëÇ~ó=pÉëëáçåë= sçäìãÉ=ff= = Potential Cost Savings for Use of 3D Printing Combined With 3D...TYPE 3. DATES COVERED 00-00-2014 to 00-00-2014 4. TITLE AND SUBTITLE Potential Cost Savings for Use of 3D Printing Combined With 3D Imaging and...Chair: RADM David Lewis, USN Program Executive Officer, SHIPS Potential Cost Savings for Use of 3D Printing Combined With 3D Imaging and CPLM for

Recent trends in print portals and Web2Print applications

Science.gov (United States)

Tuijn, Chris

2009-01-01

For quite some time now, the printing business has been under heavy pressure because of overcapacity, dropping prices and the delocalization of the production to low income countries. To survive in this competitive world, printers have to invest in tools that, on one hand, reduce the production costs and, on the other hand, create additional value for their customers (print buyers). The creation of customer portals on top of prepress production systems allowing print buyers to upload their content, approve the uploaded pages based on soft proofs (rendered by the underlying production system) and further follow-up the generation of the printed material, has been illustrative in this respect. These developments resulted in both automation for the printer and added value for the print buyer. Many traditional customer portals assume that the printed products have been identified before they are presented to the print buyer in the portal environment. The products are, in this case, typically entered by the printing organization in a so-called MISi system after the official purchase order has been received from the print buyer. Afterwards, the MIS system then submits the product to the customer portal. Some portals, however, also support the initiation of printed products by the print buyer directly. This workflow creates additional flexibility but also makes things much more complex. We here have to distinguish between special products that are defined ad-hoc by the print buyer and standardized products that are typically selected out of catalogs. Special products are most of the time defined once and the level of detail required in terms of production parameters is quite high. Systems that support such products typically have a built-in estimation module, or, at least, a direct connection to an MIS system that calculates the prices and adds a specific mark-up to calculate a quote. Often, the markup is added by an account manager on a customer by customer basis; in this

Internet printing

Science.gov (United States)

Rahgozar, M. Armon; Hastings, Tom; McCue, Daniel L.

1997-04-01

The Internet is rapidly changing the traditional means of creation, distribution and retrieval of information. Today, information publishers leverage the capabilities provided by Internet technologies to rapidly communicate information to a much wider audience in unique customized ways. As a result, the volume of published content has been astronomically increasing. This, in addition to the ease of distribution afforded by the Internet has resulted in more and more documents being printed. This paper introduces several axes along which Internet printing may be examined and addresses some of the technological challenges that lay ahead. Some of these axes include: (1) submission--the use of the Internet protocols for selecting printers and submitting documents for print, (2) administration--the management and monitoring of printing engines and other print resources via Web pages, and (3) formats--printing document formats whose spectrum now includes HTML documents with simple text, layout-enhanced documents with Style Sheets, documents that contain audio, graphics and other active objects as well as the existing desktop and PDL formats. The format axis of the Internet Printing becomes even more exciting when one considers that the Web documents are inherently compound and the traversal into the various pieces may uncover various formats. The paper also examines some imaging specific issues that are paramount to Internet Printing. These include formats and structures for representing raster documents and images, compression, fonts rendering and color spaces.

Digital Inkjet Textile Printing

OpenAIRE

Wang, Meichun

2017-01-01

Digital inkjet textile printing is an emerging technology developed with the rise of the digital world. It offers a possibility to print high-resolution images with unlimited color selection on fabrics. Digital inkjet printing brings a revolutionary chance for the textile printing industry. The history of textile printing shows the law how new technology replaces the traditional way of printing. This indicates the future of digital inkjet textile printing is relatively positive. Differen...

Printed photodetectors

International Nuclear Information System (INIS)

Pace, Giuseppina; Grimoldi, Andrea; Sampietro, Marco; Natali, Dario; Caironi, Mario

2015-01-01

Photodetectors convert light pulses into electrical signals and are fundamental building blocks for any opto-electronic system adopting light as a probe or information carrier. They have widespread technological applications, from telecommunications to sensors in industrial, medical and civil environments. Further opportunities are plastic short-range communications systems, interactive large-area surfaces and light-weight, flexible, digital imagers. These applications would greatly benefit from the cost-effective fabrication processes enabled by printing technology. While organic semiconductors are the most investigated materials for printed photodetectors, and are the main focus of the present review, there are notable examples of other inorganic or hybrid printable semiconductors for opto-electronic systems, such as quantum-dots and nanowires. Here we propose an overview on printed photodetectors, including three-terminal phototransistors. We first give a brief account of the working mechanism of these light sensitive devices, and then we review the recent progress achieved with scalable printing techniques such as screen-printing, inkjet and other non-contact technologies in the development of all-printed or hybrid systems. (paper)

Printed photodetectors

Science.gov (United States)

Pace, Giuseppina; Grimoldi, Andrea; Sampietro, Marco; Natali, Dario; Caironi, Mario

2015-10-01

Photodetectors convert light pulses into electrical signals and are fundamental building blocks for any opto-electronic system adopting light as a probe or information carrier. They have widespread technological applications, from telecommunications to sensors in industrial, medical and civil environments. Further opportunities are plastic short-range communications systems, interactive large-area surfaces and light-weight, flexible, digital imagers. These applications would greatly benefit from the cost-effective fabrication processes enabled by printing technology. While organic semiconductors are the most investigated materials for printed photodetectors, and are the main focus of the present review, there are notable examples of other inorganic or hybrid printable semiconductors for opto-electronic systems, such as quantum-dots and nanowires. Here we propose an overview on printed photodetectors, including three-terminal phototransistors. We first give a brief account of the working mechanism of these light sensitive devices, and then we review the recent progress achieved with scalable printing techniques such as screen-printing, inkjet and other non-contact technologies in the development of all-printed or hybrid systems.

3D printing PLGA: a quantitative examination of the effects of polymer composition and printing parameters on print resolution.

Science.gov (United States)

Guo, Ting; Holzberg, Timothy R; Lim, Casey G; Gao, Feng; Gargava, Ankit; Trachtenberg, Jordan E; Mikos, Antonios G; Fisher, John P

2017-04-12

In the past few decades, 3D printing has played a significant role in fabricating scaffolds with consistent, complex structure that meet patient-specific needs in future clinical applications. Although many studies have contributed to this emerging field of additive manufacturing, which includes material development and computer-aided scaffold design, current quantitative analyses do not correlate material properties, printing parameters, and printing outcomes to a great extent. A model that correlates these properties has tremendous potential to standardize 3D printing for tissue engineering and biomaterial science. In this study, we printed poly(lactic-co-glycolic acid) (PLGA) utilizing a direct melt extrusion technique without additional ingredients. We investigated PLGA with various lactic acid:glycolic acid (LA:GA) molecular weight ratios and end caps to demonstrate the dependence of the extrusion process on the polymer composition. Micro-computed tomography was then used to evaluate printed scaffolds containing different LA:GA ratios, composed of different fiber patterns, and processed under different printing conditions. We built a statistical model to reveal the correlation and predominant factors that determine printing precision. Our model showed a strong linear relationship between the actual and predicted precision under different combinations of printing conditions and material compositions. This quantitative examination establishes a significant foreground to 3D print biomaterials following a systematic fabrication procedure. Additionally, our proposed statistical models can be applied to couple specific biomaterials and 3D printing applications for patient implants with particular requirements.

3D printing PLGA: a quantitative examination of the effects of polymer composition and printing parameters on print resolution

Science.gov (United States)

Guo, Ting; Holzberg, Timothy R; Lim, Casey G; Gao, Feng; Gargava, Ankit; Trachtenberg, Jordan E; Mikos, Antonios G; Fisher, John P

2018-01-01

In the past few decades, 3D printing has played a significant role in fabricating scaffolds with consistent, complex structure that meet patient-specific needs in future clinical applications. Although many studies have contributed to this emerging field of additive manufacturing, which includes material development and computer-aided scaffold design, current quantitative analyses do not correlate material properties, printing parameters, and printing outcomes to a great extent. A model that correlates these properties has tremendous potential to standardize 3D printing for tissue engineering and biomaterial science. In this study, we printed poly(lactic-co-glycolic acid) (PLGA) utilizing a direct melt extrusion technique without additional ingredients. We investigated PLGA with various lactic acid: glycolic acid (LA:GA) molecular weight ratios and end caps to demonstrate the dependence of the extrusion process on the polymer composition. Micro-computed tomography was then used to evaluate printed scaffolds containing different LA:GA ratios, composed of different fiber patterns, and processed under different printing conditions. We built a statistical model to reveal the correlation and predominant factors that determine printing precision. Our model showed a strong linear relationship between the actual and predicted precision under different combinations of printing conditions and material compositions. This quantitative examination establishes a significant foreground to 3D print biomaterials following a systematic fabrication procedure. Additionally, our proposed statistical models can be applied to couple specific biomaterials and 3D printing applications for patient implants with particular requirements. PMID:28244880

Hybrid Heritage: An Investigation into the Viability of 3D-Printed Mashrabiya Window Screens for Bahraini Dwellings

OpenAIRE

Almerbati, Nehal

2016-01-01

Current debates on design and manufacturing support the claim that the ‘Third Industrial Revolution’ has already started due to Additive Manufacturing (AM) and 3D Printing. The process of solidifying liquid or powder using a binding agent or a melting laser can save time and transportation costs associated with importing primary material if locally sourced material is available. This research investigates a framework approach, titled SAFE, for discussing the functionality, economic viability,...

Free E-Books May Increase Print Sales: A Study with Mixed Results. A Review of: Hilton, J. III, & Wiley, D. (2010. The short-term influence of free digital versions of books on print sales. Journal of Electronic Publishing, 13(1.

Directory of Open Access Journals (Sweden)

Heather R. Williams

2011-03-01

Full Text Available Objective – To determine whether the availability of free digital versions of books impacts print sales.Design – Quantitative data comparison.Setting – University Instructional Psychology Department.Subjects – A total of 41 books, each with a free digital version and a traditional print version.Methods – This study used Nielson BookScan data to track print book sales during a 16-week period, 8 weeks before a free digital version of the book became available and 8 weeks after the availability of the free digital version. The authors tracked 41 books and organized them into four categories. The first included 7 nonfiction books, the second consisted of 5 science fiction/fantasy books, the third included 5 science fiction/fantasy books released together by Random House, and the fourth group consisted of 24 science fiction/fantasy books released by Tor Books. The books released by Tor Books, unlike the other books in the study, were available by free download only if a person registered for Tor’s newsletter and the downloads were only available for one week. When a free digital book from any of the other three groups was released, it remained available for several weeks, and more often, indefinitely.Main Results – Combined print sales of the nonfiction titles in the first group increased 5% after the release of a free digital copy. The majority of the science fiction/fantasy books in the second group also had an increase in post-free release sales, with a combined increase of 26%. The combined sales of the Random House titles increased by 9% after the release of the free digital versions. However, in stark contrast to the results of the first three groups, the fourth group of Tor books had a combined decrease in print sales of 18%. While the authors were not able to explain this difference with certainty, they point out that the Tor model for releasing the free digital books (making the free books available for only one week and

Printing Insecurity? The Security Implications of 3D-Printing of Weapons.

Science.gov (United States)

Walther, Gerald

2015-12-01

In 2013, the first gun printed out of plastic by a 3D-printer was successfully fired in the U.S. This event caused a major media hype about the dangers of being able to print a gun. Law enforcement agencies worldwide were concerned about this development and the potentially huge security implications of these functional plastic guns. As a result, politicians called for a ban of these weapons and a control of 3D-printing technology. This paper reviews the security implications of 3D-printing technology and 3D guns. It argues that current arms control and transfer policies are adequate to cover 3D-printed guns as well. However, while this analysis may hold up currently, progress in printing technology needs to be monitored to deal with future dangers pre-emptively.

42 CFR 476.86 - Correlation of Title XI functions with Title XVIII functions.

Science.gov (United States)

2010-10-01

... 42 Public Health 4 2010-10-01 2010-10-01 false Correlation of Title XI functions with Title XVIII functions. 476.86 Section 476.86 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF...) Qio Review Functions § 476.86 Correlation of Title XI functions with Title XVIII functions. (a...

20 CFR 404.535 - How much will we withhold from your title VIII and title XVI benefits to recover a title II...

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false How much will we withhold from your title... Officer § 404.535 How much will we withhold from your title VIII and title XVI benefits to recover a title II overpayment? (a) If past-due benefits are payable to you, we will withhold the lesser of the...

Health content analysis of organ donation and transplantation news on Turkish television channels and in Turkish print media.

Science.gov (United States)

Colak, M Yavuz; Hekimoglu, D; Ersoy, K; Sozen, F; Haberal, M

2010-01-01

The media affects individuals' behaviors, especially by means of news and advertisements. In this study, we evaluated health content of organ donation and transplantation news in the printed media and on television programs for a 1-year period in Turkey. We examined 2449 news items in 230 newspapers and magazines; 1179 news programs on 45 television channels, all concerning organ donation and transplantation. The news obtained from the Media Pursuit Center were transferred to an electronic file to evaluate the format and content of the news. Nine variables were examined about the scope and the formal characteristics of the news: the publication name, its type, the province, the date, the headline, the title length, the presence of a photograph, or its kind, the news size, and the page number. In the content analysis of the news, we also examined 9 variables: the topic, the message of the headline, the property of the words in the title, the identification of photographs in the news, the age, gender of actors in the news, as well as donor or recipient. In a summary, print media and television channels, failed to show sufficient information about organ donation and transplantation. The percentage of news about organ donation and transplantation was small and mostly negative items in the media. On television channels, sufficient place was not given to organ donation and transplantation. The news in printed media and on television channels was not about motivated or altruistic behavior. The pattern of organ donation and transplantation news is important in terms of perception and comment by the public. Furthermore it directly affects the perception of the news by the reader.

Print Finishing: From Manual to Automated Print Finishing

Directory of Open Access Journals (Sweden)

Gareth Ward

2004-12-01

Full Text Available Meeting the demand for faster turnrounds and shorter print runs goes beyond making the printing press easier to set up and change. There is little point in producing plates and then sheets from a press if the post press area does not change to keep abreast of developments in prepress and the print room. The greatest impact is going to come from JDF, the end to end production data format which is finding wide spread acceptance in print areas. To date finishing equipment manufacturers are not as well represented within the CIP4 organisation as prepress and press vendors, but the major manufacturers are members. All are working to the goal of complete connectivity.The idea of JDF is that if the format of a print product like a magazine is known during the creation phases, the information can be used to preset machinery that is going to be used to produce it, so avoiding input errors and saving manufacturing time.A second aspect to JDF is that information about performance and progress is gathered and can be retrieved from a central point or made available to a customer. Production scheduling and costing becomes more accurate and customer relationships are deepened. However JDF to its fullest extent is not yet in use in connecting the finishing area to the rest of the printing plant. Around the world different companies are testing the idea of JDF to connect saddle stitchers, guillotines and binders with frantic work underway to be able to show results soon.

A high speed electrohydrodynamic (EHD) jet printing method for line printing

International Nuclear Information System (INIS)

Phung, Thanh Huy; Kim, Seora; Kwon, Kye-Si

2017-01-01

Electrohydrodynamic (EHD) jet printing has drawn attention due to its capability to produce smaller dots and patterns with finer lines when compared to those obtained from using conventional inkjet printing. Previous studies have suggested that drop-on-demand EHD-patterning applications should be limited to very slow printing cases with speeds far less than 10 mm s −1 due to the small dot size and limited jetting frequency. In this study, a new EHD printing method is proposed to significantly increase the line-patterning printing speed by modifying the ink and thereby changing the relic shape. The proposed method has the additional advantage of reducing the line-pattern width. The results of the experiment show that the pattern width could be reduced from 20 µ m to 4 µ m by increasing the printing speed from 10 mm s −1 to 50 mm s −1 , respectively. (paper)

Engraving Print Classification

International Nuclear Information System (INIS)

Hoelck, Daniel; Barbe, Joaquim

2008-01-01

A print is a mark, or drawing, made in or upon a plate, stone, woodblock or other material which is cover with ink and then is press usually into a paper reproducing the image on the paper. Engraving prints usually are image composed of a group of binary lines, specially those are made with relief and intaglio techniques. Varying the number and the orientation of lines, the drawing of the engraving print is conformed. For this reason we propose an application based on image processing methods to classify engraving prints

Printing Insecurity? The Security Implications of 3D-Printing of Weapons

OpenAIRE

Walther, Gerald

2014-01-01

In 2013, the first gun printed out of plastic by a 3D-printer was successfully fired in the US. This event caused a major media hype about the dangers of being able to print a gun. Law enforcement agencies worldwide were concerned about this development and the potentially huge security implications of these functional plastic guns. As a result, politicians called for a ban of these weapons and a control of 3D-printing technology. This paper reviews the security implications of 3D-printing te...

Adult rat retinal ganglion cells and glia can be printed by piezoelectric inkjet printing

International Nuclear Information System (INIS)

Lorber, Barbara; Martin, Keith R; Hsiao, Wen-Kai; Hutchings, Ian M

2014-01-01

We have investigated whether inkjet printing technology can be extended to print cells of the adult rat central nervous system (CNS), retinal ganglion cells (RGC) and glia, and the effects on survival and growth of these cells in culture, which is an important step in the development of tissue grafts for regenerative medicine, and may aid in the cure of blindness. We observed that RGC and glia can be successfully printed using a piezoelectric printer. Whilst inkjet printing reduced the cell population due to sedimentation within the printing system, imaging of the printhead nozzle, which is the area where the cells experience the greatest shear stress and rate, confirmed that there was no evidence of destruction or even significant distortion of the cells during jet ejection and drop formation. Importantly, the viability of the cells was not affected by the printing process. When we cultured the same number of printed and non-printed RGC/glial cells, there was no significant difference in cell survival and RGC neurite outgrowth. In addition, use of a glial substrate significantly increased RGC neurite outgrowth, and this effect was retained when the cells had been printed. In conclusion, printing of RGC and glia using a piezoelectric printhead does not adversely affect viability and survival/growth of the cells in culture. Importantly, printed glial cells retain their growth-promoting properties when used as a substrate, opening new avenues for printed CNS grafts in regenerative medicine. (paper)

Advances in Home Photo Printing

Institute of Scientific and Technical Information of China (English)

Qian Lin; Brian Atkins; Huitao Luo

2004-01-01

With digital camera adoptions going main stream, consumers capture a record number of photos.Currently, the majority of the digital photos are printed at home. One of the key enablers of this transformation is the advancement of home photo printing technologies. In the past few years, inkjet printing technologies have continued to deliver smaller drop size, larger number of inks, and longer-lasting prints. In the mean time, advanced image processing automatically enhances captured digital photos while being printed. The combination of the above two forces has closed the gap between the home photo prints and AgX prints. It will give an overview of the home photo printing market and technology trends, and discuss major advancements in automatic image processing.

Printed Electronics

Science.gov (United States)

Korkut, Sibel (Inventor); Chiang, Katherine S. (Inventor); Crain, John M. (Inventor); Aksay, Ilhan A. (Inventor); Lettow, John S. (Inventor); Chen, Chuan-Hua (Inventor); Prud'Homme, Robert K. (Inventor)

2018-01-01

Printed electronic device comprising a substrate onto at least one surface of which has been applied a layer of an electrically conductive ink comprising functionalized graphene sheets and at least one binder. A method of preparing printed electronic devices is further disclosed.

Printing Has a Future

Directory of Open Access Journals (Sweden)

Hans Georg Wenke

2004-12-01

Full Text Available Printing will also be done in the future. Printed items meet basic needs and are deeply anchored in people’s habits. Being able to handle and collect printed matter is highly attractive. And paper is now more alive than ever. It is therefore too shortsighted to disclaim the importance of one of the still large economic sectors just because of a few looming-recession instigated market shifts.The exciting aspect of drupa 2004 is: printing will be reinvented, so to speak. Much more printing will be done in the future than at present. On the one hand, people are concentrating on process optimization and automation to ensure this. Measuring and testing, process control and optimization, and linking up "office software" with printing technology will be very central topics at drupa 2004. Electronics and print are not rivals; a symbiosis exists. And printing is high-tech: hardly any other multifaceted sector which has been so successful for centuries is as computerized as the printing industry.A series of "new chapters" in the variety of printing possibilities will be opened at drupa. Talk will be generated by further technical developments, often the connection between paper/cardboard and electronics, the link between the office world and graphics industry, text databases and their link-up to graphic page production tools, and "on the fly" dynamic printing over networks.All of this and more belongs to future potentialities, which are so substantial overall, the outlook is by no means black for the "black art". Like its predecessors, drupa 2004 is also a product trade fair. However, more than ever before in its history, it is also an "information village". The exhibits are useful, because they occasionally make what this means visible.

Printing quality control automation

Science.gov (United States)

Trapeznikova, O. V.

2018-04-01

One of the most important problems in the concept of standardizing the process of offset printing is the control the quality rating of printing and its automation. To solve the problem, a software has been developed taking into account the specifics of printing system components and the behavior in printing process. In order to characterize the distribution of ink layer on the printed substrate the so-called deviation of the ink layer thickness on the sheet from nominal surface is suggested. The geometric data construction the surface projections of the color gamut bodies allows to visualize the color reproduction gamut of printing systems in brightness ranges and specific color sectors, that provides a qualitative comparison of the system by the reproduction of individual colors in a varying ranges of brightness.

Browse Title Index

African Journals Online (AJOL)

2004): Special Issue 2004, Differential production of immune parameters by mouse strains ... agglutination and complement fixation tests in the field diagnosis ... List All Titles · Free To Read Titles This Journal is Open Access.

Solvents interactions with thermochromic print

Directory of Open Access Journals (Sweden)

Mirela Rožić

2017-12-01

Full Text Available In this study, the interactions between different solvents (benzene, acetone, cyclohexanone, various alcohols and water and thermochromic printing ink were investigated. Thermochromic printing ink was printed on metal surface. Components of thermochromic printing inks are polymeric microcapsules and classic yellow offset printing ink. Below its activation temperature, dye and developer within the microcapsules form a blue coloured complex. Therefore, thermochromic print is green. By heating above the activation temperature, blue colour of the complex turns into the leuco dye colourless state and the green colour of the prints turns into the yellow colour of the classic offset pigment. The results of the interaction with various solvents show that the thermochromic print is stable in all tested solvents except in ethanol, acetone and cyclohexanone. In ethanol, the green colour of the print becomes yellow. SEM analysis shows that microcapsules are dissolved. In acetone and cyclohexanone, the green colour of the print turns into blue, and the microcapsules become significantly more visible. Thus, the yellow pigment interacts with examined ketones. Based on the obtained interactions it can be concluded that the microcapsules have more polar nature than the classical pigment particles. Solvent-thermocromic print interactions were analysed using Hansen solubility parameters that rank the solvents based on their estimated interaction capabilities.

Three-dimensional bio-printing.

Science.gov (United States)

Gu, Qi; Hao, Jie; Lu, YangJie; Wang, Liu; Wallace, Gordon G; Zhou, Qi

2015-05-01

Three-dimensional (3D) printing technology has been widely used in various manufacturing operations including automotive, defence and space industries. 3D printing has the advantages of personalization, flexibility and high resolution, and is therefore becoming increasingly visible in the high-tech fields. Three-dimensional bio-printing technology also holds promise for future use in medical applications. At present 3D bio-printing is mainly used for simulating and reconstructing some hard tissues or for preparing drug-delivery systems in the medical area. The fabrication of 3D structures with living cells and bioactive moieties spatially distributed throughout will be realisable. Fabrication of complex tissues and organs is still at the exploratory stage. This review summarize the development of 3D bio-printing and its potential in medical applications, as well as discussing the current challenges faced by 3D bio-printing.

Printing at CERN

CERN Multimedia

Otto, R

2007-01-01

For many years CERN had a very sophisticated print server infrastructure which supported several different protocols (AppleTalk, IPX and TCP/IP) and many different printing standards. Today’s situation differs a lot: we have a much more homogenous network infrastructure, where TCP/IP is used everywhere and we have less printer models, which almost all work using current standards (i.e. they all provide PostScript drivers). This change gave us the possibility to review the printing architecture aiming at simplifying the infrastructure in order to achieve full automation of the service. The new infrastructure offers both: LPD service exposing print queues to Linux and Mac OS X computers and native printing for Windows based clients. The printer driver distribution is automatic and native on Windows and automated by custom mechanisms on Linux, where the appropriate Foomatic drivers are configured. Also the process of printer registration and queue creation is completely automated following the printer regis...

INIS: Authority List for Journal Titles

International Nuclear Information System (INIS)

1992-01-01

This is the nineteenth revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). It lists 10,797 journal titles which have contained articles within the scope of INIS. The purpose of this Authority List is to provide descriptive cataloguers with a standard abbreviation for journal titles and to assist users of INIS products with a tool for verifying the full title of a journal. A journal, or periodical, is generally published within a defined, fixed interval between issues, which usually has more than one issue a year, and which usually includes a mixture of articles, letters, summaries, etc. Within this definition, annuals such as Annual Review of Nuclear Science are included. Series titles as, for example the McGraw-Hill Series in Nuclear Engineering, are not included in this Authority. Entries: Each entry consists of: - the full journal title (highlighted); - the abbreviated title; - ISSN, if available; - CODEN, if available; - additional information related to the journal title. Arrangement: In Part I, the full journal titles are grouped by country or international organization name and ordered alphabetically, followed by the ISSN, the CODEN in square brackets if available, and then the abbreviated title. The abbreviated title is based on the rules of ISO 4: Documentation - International Code for the Abbreviation of Titles of Periodicals. The abbreviations of the words are taken from the ISDS List of Periodical Title Word Abbreviation. In Part II, the order of the citations is reversed: the abbreviated journal titles are arranged alphabetically, followed by country code. Then the full journal titles are followed by the country of publication, and if available, ISSN and CODEN. Additional Information: There is important information related to the journal titles which are fundamental for tracing the history of the title and the present status. They are listed below and are entered whenever applicable: - Ceased publication; - Superseded by

Title IX Resource Guide

Science.gov (United States)

Office for Civil Rights, US Department of Education, 2015

2015-01-01

Title IX of the Education Amendments of 1972 (Title IX) prohibits discrimination based on sex in education programs and activities in federally funded schools at all levels. If any part of a school district or college receives any Federal funds for any purpose, all of the operations of the district or college are covered by Title IX. The essence…

Getting to one from title 10 + title 32 unity of effort in the homeland

OpenAIRE

Prosch, Caroline Ross.

2011-01-01

CHDS State/Local Approved for public release; distribution is unlimited This thesis bridges the knowledge gap between Title 10 Active Duty and Title 32 National Guard in order to breakdown cultural barriers and reach unity of effort for response operations in the homeland. Regrettably, a unified response was missing among Title 10 Active Duty and Title 32 National Guard members following Hurricane Katrina. Since then, initiatives based in doctrine, statutes and formal recommendations...

Printing nanotube/nanowire for flexible microsystems

Science.gov (United States)

Tortorich, Ryan P.; Choi, Jin-Woo

2014-04-01

Printing has become an emerging manufacturing technology for mechanics, electronics, and consumer products. Additionally, both nanotubes and nanowires have recently been used as materials for sensors and electrodes due to their unique electrical and mechanical properties. Printed electrodes and conductive traces particularly offer versatility of fabricating low-cost, disposable, and flexible electrical devices and microsystems. While various printing methods such as screen printing have been conventional methods for printing conductive traces and electrodes, inkjet printing has recently attracted great attention due to its unique advantages including no template requirement, rapid printing at low cost, on-demand printing capability, and precise control of the printed material. Computer generated conductive traces or electrode patterns can simply be printed on a thin film substrate with proper conductive ink consisting of nanotubes or nanowires. However, in order to develop nanotube or nanowire ink, there are a few challenges that need to be addressed. The most difficult obstacle to overcome is that of nanotube/nanowire dispersion within a solution. Other challenges include adjusting surface tension and controlling viscosity of the ink as well as treating the surface of the printing substrate. In an attempt to pave the way for nanomaterial inkjet printing, we present a method for preparing carbon nanotube ink as well as its printing technique. A fully printed electrochemical sensor using inkjet-printed carbon nanotube electrodes is also demonstrated as an example of the possibilities for this technology.

Browse Title Index

African Journals Online (AJOL)

Items 601 - 650 of 788 ... Browse Title Index ... Issue, Title ... Vol 14, No 1 (2006), Social science research: a critique of quantitative and qualitative methods ... Vol 18, No 1 (2010), Stress among part-time business students: a study in a Ghanaian ...

Colour changes in prints during long-term dark storage of prints

International Nuclear Information System (INIS)

Parraman, Carinna

2010-01-01

The most significant impact on colour fading in prints is exposure to light and air. However what happens to coloured prints during long-term storage in boxes, drawers and on shelves? Measurements of samples, printed in July 2005, stored in a range of light and darkened storage conditions have shown some interesting initial results. As more emphasis is placed on the effects of light, the dark stability of inkjet prints is relatively overlooked when considering how to preserve or store coloured prints. This study and presentation builds on previous research [1] and has concentrated on the changes to colour during storage. With reference to ASTM F2035 - 00(2006) Standard Practice for Measuring the Dark Stability of Ink Jet Prints, the Standards outline points out that whilst natural aging is the most reliable method of assessing image stability, materials and inks any data that is produced quickly becomes redundant; therefore accelerated aging is more preferred. However, the fine art materials in this study are still very much in circulation. The leading fine art papers, and pigmented ink-sets used in these trials are still being used by artists. We can therefore demonstrate the characteristics of colour changes and the impact of ink on paper that utilises natural aging methods.

20 CFR 408.931 - How much will we withhold from your title II and title XVI benefits to recover a title VIII...

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false How much will we withhold from your title II... and Overpayments Adjustment of Title II Benefits § 408.931 How much will we withhold from your title...-due benefits. (b)(1) We will collect the overpayment from current monthly benefits due in a month...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 229 ... Browse Title Index ... Issue, Title. Vol 14, No 2 ... Vol 15, No 1 (2017), Qualitative and quantitative methods of suicide research in old age, Abstract PDF ... Vol 11, No 2 (2013), Simple Algorithm in the Management of Fetal ...

A Vector Printing Method for High-Speed Electrohydrodynamic (EHD Jet Printing Based on Encoder Position Sensors

Directory of Open Access Journals (Sweden)

Thanh Huy Phung

2018-02-01

Full Text Available Electrohyrodynamic (EHD jet printing has been widely used in the field of direct micro-nano patterning applications, due to its high resolution printing capability. So far, vector line printing using a single nozzle has been widely used for most EHD printing applications. However, the application has been limited to low-speed printing, to avoid non-uniform line width near the end points where line printing starts and ends. At end points of line vector printing, the deposited drop amount is likely to be significantly large compared to the rest of the printed lines, due to unavoidable acceleration and deceleration. In this study, we proposed a method to solve the printing quality problems by producing droplets at an equally spaced distance, irrespective of the printing speed. For this purpose, an encoder processing unit (EPU was developed, so that the jetting trigger could be generated according to user-defined spacing by using encoder position signals, which are used for the positioning control of the two linear stages.

Some Thoughts on Contemporary Graphic Print

Directory of Open Access Journals (Sweden)

Stefan Skiba

2016-09-01

Full Text Available The production requirements of original graphic works of art have changed since 1980. The development of digital printing using lightfast colors now rivals traditional techniques such as wood cut, screen print, lithography, etching etc. Today, with respect to artistic legitimacy, original graphics using traditional printing techniques compete with original graphics produced by digital printing techniques on the art market. What criteria distinguish traditional printing techniques from those of digital printing in the production and acquisition of original graphics? What consequences is the serious artist faced with when deciding to implement digital print production? How does digital print change original graphic acquisition decisions?

Colour printing techniques

OpenAIRE

Parraman, C.

2017-01-01

Invited chapter in the book Colour Design: Theories and Applications. In PART 3 COLOUR, DESIGN AND COLORATION this chapter covers:\\ud - Hardcopy colour: analogue versus digital\\ud - Colour theory in relation to printing\\ud - Overview of halftoning and digital print technologies\\ud - Overview and development of inks\\ud - Inkjet papers and inks\\ud - Recent and future trends in colour, printing inks and hardware.\\ud \\ud This book differs from other existing books in the field, with the aim of an...

Print and Manuscript

OpenAIRE

Erne, Lukas Christian

2007-01-01

Positioning Shakespeare at the "crossroads of manuscript and print" and exploring what the choice of print or manuscript reveals about the poet's intended audience and the social persona the poet wanted to assume and fashion, argues that "Shakespeare's authorial self-presentation begins as a poet and, more specifically, as a print-published poet" with the publication of Venus and Adonis in 1593 and the allusion to the publication of Rape of Lucrece in the next year. Yet also considers the imp...

Printed Electronics

Science.gov (United States)

Wade, Jessica; Hollis, Joseph Razzell; Wood, Sebastian

2018-04-01

The combination of printing technology with manufacturing electronic devices enables a new paradigm of printable electronics, where 'smart' functionality can be readily incorporated into almost any product at low cost. Over recent decades, rapid progress has been made in this field, which is now emerging into the industrial andcommercial realm. However, successful development and commercialisation on a large scale presents some significant technical challenges. For fully-printable electronic systems, all the component parts must be deposited from solutions (inks), requiring the development of new inorganic, organic and hybrid materials.A variety of traditional printing techniques are being explored and adapted forprinting these new materials in ways that result in the best performing electronicdevices. Whilst printed electronics research has initially focused on traditional typesof electronic device such as light-emitting diodes, transistors, and photovoltaics, it is increasingly apparent that a much wider range of applications can be realised. The soft and stretchable nature of printable materials makes them perfect candidates forbioelectronics, resulting in a wealth of research looking at biocompatible printable inks and biosensors. Regardless of application, the properties of printed electronicmaterials depend on the chemical structures, processing conditions, device architecture,and operational conditions, the complex inter-relationships of which aredriving ongoing research. We focus on three particular 'hot topics', where attention is currently focused: novel materials, characterisation techniques, and device stability. With progress advancing very rapidly, printed electronics is expected to grow over the next decade into a key technology with an enormous economic and social impact.

INIS: Authority list for journal titles

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-03-01

This is the twenty-ninth revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). It lists the titles of 12 990 journals which have contained articles within the scope of INIS. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the reader to find titles easily, the list is divided into two parts. In Part I, the full journal titles are grouped by country or international organization responsible for coverage and ordered alphabetically. In Part II, the full journal titles of all countries or international organizations are arranged alphabetically. The country name or the international organization name responsible for coverage of the journal title to INIS is entered in parentheses. Journal titles marked with an asterisk are regularly scanned by INIS. Titles that have been identified by INIS Centres as 'Key Journals' are marked with the hash sign.

INIS: Authority list for journal titles

International Nuclear Information System (INIS)

2003-01-01

This is the twenty-ninth revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). It lists the titles of 12 990 journals which have contained articles within the scope of INIS. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the reader to find titles easily, the list is divided into two parts. In Part I, the full journal titles are grouped by country or international organization responsible for coverage and ordered alphabetically. In Part II, the full journal titles of all countries or international organizations are arranged alphabetically. The country name or the international organization name responsible for coverage of the journal title to INIS is entered in parentheses. Journal titles marked with an asterisk are regularly scanned by INIS. Titles that have been identified by INIS Centres as 'Key Journals' are marked with the hash sign

Cost-estimating for commercial digital printing

Science.gov (United States)

Keif, Malcolm G.

2007-01-01

The purpose of this study is to document current cost-estimating practices used in commercial digital printing. A research study was conducted to determine the use of cost-estimating in commercial digital printing companies. This study answers the questions: 1) What methods are currently being used to estimate digital printing? 2) What is the relationship between estimating and pricing digital printing? 3) To what extent, if at all, do digital printers use full-absorption, all-inclusive hourly rates for estimating? Three different digital printing models were identified: 1) Traditional print providers, who supplement their offset presswork with digital printing for short-run color and versioned commercial print; 2) "Low-touch" print providers, who leverage the power of the Internet to streamline business transactions with digital storefronts; 3) Marketing solutions providers, who see printing less as a discrete manufacturing process and more as a component of a complete marketing campaign. Each model approaches estimating differently. Understanding and predicting costs can be extremely beneficial. Establishing a reliable system to estimate those costs can be somewhat challenging though. Unquestionably, cost-estimating digital printing will increase in relevance in the years ahead, as margins tighten and cost knowledge becomes increasingly more critical.

A STUDY OF RELATIVE CORRELATION BETWEEN THE PATTERN OF FINGER PRINTS AND LIP PRINTS

OpenAIRE

Murugan; Karikalan

2014-01-01

BACKGROUND AND OBJECTIVE: The use of conventional methods such as dactylography (study of finger prints) & cheiloscopy (study of lip prints) is of paramount importance, since personal identification by other means such as DNA analysis is sophisticated and not available in rural and developing countries. Fingerprint in its narrow sense is an impression left by the friction ridges of human fingers. The second prints of interest are lip prints. Studies of association between ...

CERN printing infrastructure

International Nuclear Information System (INIS)

Otto, R; Sucik, J

2008-01-01

For many years CERN had a very sophisticated print server infrastructure [13] which supported several different protocols (AppleTalk, IPX and TCP/IP) and many different printing standards. Today's situation differs a lot: we have a much more homogenous network infrastructure, where TCP/IP is used everywhere and we have less printer models, which almost all work using current standards (i.e. they all provide PostScript drivers). This change gave us the possibility to review the printing architecture aiming at simplifying the infrastructure in order to achieve full automation of the service. The new infrastructure offers both: LPD service exposing print queues to Linux and Mac OS X computers and native printing for Windows based clients. The printer driver distribution is automatic and native on Windows and automated by custom mechanisms on Linux, where the appropriate Foomatic drivers are configured. Also the process of printer registration and queue creation is completely automated following the printer registration in the network database. At the end of 2006 we have moved all (∼1200) CERN printers and all users' connections at CERN to the new service. This paper will describe the new architecture and summarize the process of migration

Browse Title Index

African Journals Online (AJOL)

Items 201 - 250 of 488 ... African Journal of Paediatric Surgery. ... Ileocecal valve atresia: Introduction of a new surgical approach ... Vol 4, No 1 (2007), Isolated Bilateral Macrostomia: Case Series and ... Vol 9, No 2 (2012), Laparoscopic inguinal hernia repair in ... List All Titles · Free To Read Titles This Journal is Open Access.

Making PMT halftone prints

Energy Technology Data Exchange (ETDEWEB)

Corey, J.D.

1977-05-01

In the printing process for technical reports presently used at Bendix Kansas City Division, photographs are reproduced by pasting up PMT halftone prints on the artwork originals. These originals are used to make positive-working plastic plates for offset lithography. Instructions for making good-quality halftone prints using Eastman Kodak's PMT materials and processes are given in this report. 14 figures.

The NIH 3D Print Exchange: A Public Resource for Bioscientific and Biomedical 3D Prints.

Science.gov (United States)

Coakley, Meghan F; Hurt, Darrell E; Weber, Nick; Mtingwa, Makazi; Fincher, Erin C; Alekseyev, Vsevelod; Chen, David T; Yun, Alvin; Gizaw, Metasebia; Swan, Jeremy; Yoo, Terry S; Huyen, Yentram

2014-09-01

The National Institutes of Health (NIH) has launched the NIH 3D Print Exchange, an online portal for discovering and creating bioscientifically relevant 3D models suitable for 3D printing, to provide both researchers and educators with a trusted source to discover accurate and informative models. There are a number of online resources for 3D prints, but there is a paucity of scientific models, and the expertise required to generate and validate such models remains a barrier. The NIH 3D Print Exchange fills this gap by providing novel, web-based tools that empower users with the ability to create ready-to-print 3D files from molecular structure data, microscopy image stacks, and computed tomography scan data. The NIH 3D Print Exchange facilitates open data sharing in a community-driven environment, and also includes various interactive features, as well as information and tutorials on 3D modeling software. As the first government-sponsored website dedicated to 3D printing, the NIH 3D Print Exchange is an important step forward to bringing 3D printing to the mainstream for scientific research and education.

3D Printing A Survey

Directory of Open Access Journals (Sweden)

Muhammad Zulkifl Hasan

2017-08-01

Full Text Available Solid free fabrication SFF are produced to enhance the printing instrument utilizing distinctive strategies like Piezo spout control multi-spout injet printers or STL arrange utilizing cutting information. The procedure is utilized to diminish the cost and enhance the speed of printing. A few techniques take long at last because of extra process like dry the printing. This study will concentrate on SFFS utilizing UV gum for 3D printing.

CERN printing infrastructure

Energy Technology Data Exchange (ETDEWEB)

Otto, R; Sucik, J [CERN, Geneva (Switzerland)], E-mail: Rafal.Otto@cern.ch, E-mail: Juraj.Sucik@cern.ch

2008-07-15

For many years CERN had a very sophisticated print server infrastructure [13] which supported several different protocols (AppleTalk, IPX and TCP/IP) and many different printing standards. Today's situation differs a lot: we have a much more homogenous network infrastructure, where TCP/IP is used everywhere and we have less printer models, which almost all work using current standards (i.e. they all provide PostScript drivers). This change gave us the possibility to review the printing architecture aiming at simplifying the infrastructure in order to achieve full automation of the service. The new infrastructure offers both: LPD service exposing print queues to Linux and Mac OS X computers and native printing for Windows based clients. The printer driver distribution is automatic and native on Windows and automated by custom mechanisms on Linux, where the appropriate Foomatic drivers are configured. Also the process of printer registration and queue creation is completely automated following the printer registration in the network database. At the end of 2006 we have moved all ({approx}1200) CERN printers and all users' connections at CERN to the new service. This paper will describe the new architecture and summarize the process of migration.

Drug-printing by flexographic printing technology--a new manufacturing process for orodispersible films.

Science.gov (United States)

Janssen, Eva Maria; Schliephacke, Ralf; Breitenbach, Armin; Breitkreutz, Jörg

2013-01-30

Orodispersible films (ODFs) are intended to disintegrate within seconds when placed onto the tongue. The common way of manufacturing is the solvent casting method. Flexographic printing on drug-free ODFs is introduced as a highly flexible and cost-effective alternative manufacturing method in this study. Rasagiline mesylate and tadalafil were used as model drugs. Printing of rasagiline solutions and tadalafil suspensions was feasible. Up to four printing cycles were performed. The possibility to employ several printing cycles enables a continuous, highly flexible manufacturing process, for example for individualised medicine. The obtained ODFs were characterised regarding their mechanical properties, their disintegration time, API crystallinity and homogeneity. Rasagiline mesylate did not recrystallise after the printing process. Relevant film properties were not affected by printing. Results were comparable to the results of ODFs manufactured with the common solvent casting technique, but the APIs are less stressed through mixing, solvent evaporation and heat. Further, loss of material due to cutting jumbo and daughter rolls can be reduced. Therefore, a versatile new manufacturing technology particularly for processing high-potent low-dose or heat sensitive drugs is introduced in this study. Copyright © 2012 Elsevier B.V. All rights reserved.

The best printing methods to print satellite images

OpenAIRE

G.A. Yousif; R.Sh. Mohamed

2011-01-01

Printing systems operate in general as a system of color its color scale is limited as compared with the system color satellite images. Satellite image is building from very small cell named pixel, which represents the picture element and the unity of color when the image is displayed on the screen, this unit becomes lesser in size and called screen point. This unit posseses different size and shape from the method of printing to another, depending on the output resolution, tools and material...

MolPrint3D: Enhanced 3D Printing of Ball-and-Stick Molecular Models

Science.gov (United States)

Paukstelis, Paul J.

2018-01-01

The increased availability of noncommercial 3D printers has provided instructors and students improved access to printing technology. However, printing complex ball-and-stick molecular structures faces distinct challenges, including the need for support structures that increase with molecular complexity. MolPrint3D is a software add-on for the…

Influence of printing speed on production of embossing tools using FDM 3D printing technology

Directory of Open Access Journals (Sweden)

Jelena Žarko

2017-06-01

Full Text Available Manufacturing of the embossing tools customary implies use of metals such as zinc, magnesium, copper, and brass. In the case of short run lengths, a conventional manufacturing process and the material itself represent a significant cost, not only in the terms of material costs and the need for using complex technological systems which are necessary for their production, but also in the terms of the production time. Alternatively, 3D printing can be used for manufacturing similar embossing tools with major savings in production time and costs. However, due to properties of materials used in the 3D printing technology, expected results of embossing by 3D printed tools cannot be identical to metal ones. This problem is emphasized in the case of long run lengths and high accuracy requirement for embossed elements. The objective of this paper is primarily focused on investigating the influence of the printing speed on reproduction quality of the embossing tools printed with FDM (Fused Deposition Modelling technology. The obtained results confirmed that printing speed as a process parameter affects the reproduction quality of the embossing tools printed with FDM technology: in the case of deposition rate of 90 mm/s was noted the poorest dimensional accuracy in relation to the 3D model, which is more emphasised in case of circular and square elements. Elements printed with the highest printing speed have a greater dimensional accuracy, but with evident cracks on the surface.

Introduction to printed electronics

CERN Document Server

Suganuma, Katsuaki

2014-01-01

This book describes in detail modern technologies for printed electronics, explaining how nanotechnology and modern printing technology are merging to revolutionize electronics fabrication of thin, lightweight, large, and inexpensive products. Readers will benefit from the explanations of materials, devices and circuits used to design and implement the latest applications of printed electronics, such as thin flexible OLED displays, organic solar cells, OLED lighting, smart wallpaper, sensors, logic, memory and more.

Recent Progress in the Development of Printed Thin-Film Transistors and Circuits with High-Resolution Printing Technology.

Science.gov (United States)

Fukuda, Kenjiro; Someya, Takao

2017-07-01

Printed electronics enable the fabrication of large-scale, low-cost electronic devices and systems, and thus offer significant possibilities in terms of developing new electronics/optics applications in various fields. Almost all electronic applications require information processing using logic circuits. Hence, realizing the high-speed operation of logic circuits is also important for printed devices. This report summarizes recent progress in the development of printed thin-film transistors (TFTs) and integrated circuits in terms of materials, printing technologies, and applications. The first part of this report gives an overview of the development of functional inks such as semiconductors, electrodes, and dielectrics. The second part discusses high-resolution printing technologies and strategies to enable high-resolution patterning. The main focus of this report is on obtaining printed electrodes with high-resolution patterning and the electrical performance of printed TFTs using such printed electrodes. In the final part, some applications of printed electronics are introduced to exemplify their potential. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Prints Charles ja prints Michael külastasid Tallinna kirikuid / Allan Tammiku

Index Scriptorium Estoniae

Tammiku, Allan

2001-01-01

Prints Charles külastas 6. novembril Eesti-visiidi ajal Tallinna toomkirikut ja Pühavaimu kirikut, prints Michael viibis Tallinnas 11. novembril eravisiidil, ta külastas toomkirikut, Niguliste ja Pühavaimu kirikut

Semiotic Analysis Of Mcdonald's Printed Advertisement

OpenAIRE

URAIDA, SITI

2014-01-01

Keywords: Semiotic, printed advertisement, sign, icon, symbol, index, connotation, myth Printed advertisement has a promotional function as medium to advertise aproduct. It implicitly persuades people to create demand of product which is being advertised. In this study, the writer uses printed advertisement of McDonald's fast food company as the object. The printed advertisement was analyzed by usingSemiotics study. There are seven printed advertisements that were analyzes in this study. All ...

AirPrint Forensics: Recovering the Contents and Metadata of Printed Documents from iOS Devices

Directory of Open Access Journals (Sweden)

Luis Gómez-Miralles

2015-01-01

data they may store, opens new opportunities in the field of computer forensics. In 2010, version 4 of the iOS operating system introduced AirPrint, a simple and driverless wireless printing functionality supported by hundreds of printer models from all major vendors. This paper describes the traces left in the iOS device when AirPrint is used and presents a method for recovering content and metadata of documents that have been printed.

Durability of ink jet prints

International Nuclear Information System (INIS)

Dobric, E; Mirkovic, I Bolanca; Bolanca, Z

2010-01-01

The aim of this paper is the result presentation of some optical properties research for ink jet prints after: exposing the prints to the mixed daylight and artificial light, exposing of prints to the sun-light through the glass window, and exposing of prints to outdoor conditions during the summer months. The prints obtained by piezoelectric and thermal ink jet technologies were used in the researches. The dye-based inks and the pigmented inks based on water and the low solvent inks were used. The results of these researches, except the scientific contribution in the domain of understanding and explaining the environmental conditions on the gamut size, i.e. the range of color tonality, colorimetric stability and print quality, can be used by the ink and paper manufacturers in new formulations, offer data for the printer producers for further production and evaluation of the position of their products.

Luminous lip-prints as criminal evidence.

Science.gov (United States)

Castelló, Ana; Alvarez-Seguí, Mercedes; Verdú, Fernando

2005-12-20

Luminescence is specially a useful property for the search of invisible evidences at the scene of a crime. In the latent fingerprints particular case, there are at one's disposal fluorescent reagents for their localization. The study of latent lip prints (that is lip prints from protective lipstick, or permanent or long-lasting lipstick that do not leave any visible marks) is more recent than fingerprints study. Because of the different composition of both types of prints, different reagents have been tried out on their developing. Although, lysochromes are particularly useful reagents to obtain latent lip prints, it may occur on coloured or multicoloured surfaces, the developing is not perceived due to contrast problems between the reagent and the surface where the print is searched. Again, luminescence offers the possibility to solve this problem. Nile Red is being studied as a potential developer for latent lip prints. The results on very old prints (over 1year) indicate that this reagent is highly efficient to get latent lip prints.

Two-Way 4D Printing: A Review on the Reversibility of 3D-Printed Shape Memory Materials

Directory of Open Access Journals (Sweden)

Amelia Yilin Lee

2017-10-01

Full Text Available The rapid development of additive manufacturing and advances in shape memory materials have fueled the progress of four-dimensional (4D printing. With the right external stimulus, the need for human interaction, sensors, and batteries will be eliminated, and by using additive manufacturing, more complex devices and parts can be produced. With the current understanding of shape memory mechanisms and with improved design for additive manufacturing, reversibility in 4D printing has recently been proven to be feasible. Conventional one-way 4D printing requires human interaction in the programming (or shape-setting phase, but reversible 4D printing, or two-way 4D printing, will fully eliminate the need for human interference, as the programming stage is replaced with another stimulus. This allows reversible 4D printed parts to be fully dependent on external stimuli; parts can also be potentially reused after every recovery, or even used in continuous cycles—an aspect that carries industrial appeal. This paper presents a review on the mechanisms of shape memory materials that have led to 4D printing, current findings regarding 4D printing in alloys and polymers, and their respective limitations. The reversibility of shape memory materials and their feasibility to be fabricated using three-dimensional (3D printing are summarized and critically analyzed. For reversible 4D printing, the methods of 3D printing, mechanisms used for actuation, and strategies to achieve reversibility are also highlighted. Finally, prospective future research directions in reversible 4D printing are suggested.

Print-to-print: printer-enabled out-of-cleanroom multiobject microprinting method.

Science.gov (United States)

Xing, Siyuan; Zhao, Siwei; Pan, Tingrui

2014-01-01

Micropatterning techniques have gained growing interests from a broad range of engineering and biology researches as it realizes the high-throughput and highly quantitative investigations on miniature biological objects (e.g., cells and bacteria) by spatially defined micropatterns. However, most of the existing techniques rely on expensive instruments or intensive cleanroom access which may not be easy to be utilized in a regular biological laboratory. Here, we present the detailed procedures of a simple versatile microprinting process, referred to as Print-to-Print (P2P), to form multiobject micropatterns for potential biological applications. Only a solid-phase printer and custom-made superhydrophobic (SH) films are utilized for the printing and no thermal or chemical treatment is involved during the entire printing process. Moreover, the noncontact nature of droplet transferring and printing steps can be highly advantageous for sensitive biological uses. By the P2P process, a minimal feature resolution of 229 ± 17 μm has been successfully achieved. What's more, this approach has been applied to form micropatterning on various commonly used substrates in biology as well as multiobject co-patterns. In addition, the SH substrates have also been demonstrated to be reusable. Copyright © 2014 Elsevier Inc. All rights reserved.

Index of French nuclear literature: IBM 360 programmes for preparing the permuted index of French titles

International Nuclear Information System (INIS)

Chonez, Nicole

1968-12-01

This report contains the assembly list, the flow chart and some comments about each of the IBM 360 assembler language programmes used for preparing one of the subject indexes contained in the bibliographical bulletin entitled: 'Index de la Litterature nucleaire francaise'; this bulletin has been produced by the French C.E.A. since 1968. Only the processing phases from the magnetic tape file of the bibliographical references, assumed correct, to the printing out of the permuted index obtained with the French titles of the documents on the tape are considered here. This permuted index has the peculiarity of automatically regrouping synonyms and certain grammatical variations of the words. (author) [fr

3D-Printed Millimeter Wave Structures

Science.gov (United States)

2016-03-14

demonstrates the resolution of the printer with a 10 micron nozzle. Figure 2: Measured loss tangent of SEBS and SBS samples. 3D - Printed Millimeter... 3D printing of styrene-butadiene-styrene (SBS) and styrene ethylene/butylene-styrene (SEBS) is used to demonstrate the feasibility of 3D - printed ...Additionally, a dielectric lens is printed which improves the antenna gain of an open-ended WR-28 waveguide from 7 to 8.5 dBi. Keywords: 3D printing

Inkjet-Printed Lithium-Sulfur Microcathodes for All-Printed, Integrated Nanomanufacturing.

Science.gov (United States)

Milroy, Craig A; Jang, Seonpil; Fujimori, Toshihiko; Dodabalapur, Ananth; Manthiram, Arumugam

2017-03-01

Improved thin-film microbatteries are needed to provide appropriate energy-storage options to power the multitude of devices that will bring the proposed "Internet of Things" network to fruition (e.g., active radio-frequency identification tags and microcontrollers for wearable and implantable devices). Although impressive efforts have been made to improve the energy density of 3D microbatteries, they have all used low energy-density lithium-ion chemistries, which present a fundamental barrier to miniaturization. In addition, they require complicated microfabrication processes that hinder cost-competitiveness. Here, inkjet-printed lithium-sulfur (Li-S) cathodes for integrated nanomanufacturing are reported. Single-wall carbon nanotubes infused with electronically conductive straight-chain sulfur (S@SWNT) are adopted as an integrated current-collector/active-material composite, and inkjet printing as a top-down approach to achieve thin-film shape control over printed electrode dimensions is used. The novel Li-S cathodes may be directly printed on traditional microelectronic semicoductor substrates (e.g., SiO 2 ) or on flexible aluminum foil. Profilometry indicates that these microelectrodes are less than 10 µm thick, while cyclic voltammetry analyses show that the S@SWNT possesses pseudocapacitive characteristics and corroborates a previous study suggesting the S@SWNT discharge via a purely solid-state mechanism. The printed electrodes produce ≈800 mAh g -1 S initially and ≈700 mAh g -1 after 100 charge/discharge cycles at C/2 rate. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Remote Collaborative 3D Printing - Process Investigation

Science.gov (United States)

2016-04-01

COLLABORATIVE 3D PRINTING - PROCESS INVESTIGATION Cody M. Reese, PE CAD MODEL PRINT MODEL PRINT PREVIEW PRINTED PART AERIAL VIRTUAL This...REMOTE COLLABORATIVE 3D PRINTING - PROCESS INVESTIGATION 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER Cody M. Reese...release; distribution is unlimited. 13. SUPPLEMENTARY NOTES 14. ABSTRACT The Remote Collaborative 3D Printing project is a collaboration between

Software for Quantitative Estimation of Coefficients of Ink Transfer on the Printed Substrate in Offset Printing

Science.gov (United States)

Varepo, L. G.; Trapeznikova, O. V.; Panichkin, A. V.; Roev, B. A.; Kulikov, G. B.

2018-04-01

In the framework of standardizing the process of offset printing, one of the most important tasks is the correct selection of the printing system components, taking into account the features of their interaction and behavior in the printing process. The program allows to calculate the transfer of ink on the printed material between the contacting cylindrical surfaces of the sheet-fed offset printing apparatus with the boundaries deformation. A distinctive feature of this software product is the modeling of the liquid flow having free boundaries and causing deformation of solid boundaries when flowing between the walls of two cylinders.

32 CFR 644.62 - Title evidence.

Science.gov (United States)

2010-07-01

... HANDBOOK Acquisition Procurement of Title Evidence, Title Clearance, and Closings § 644.62 Title evidence... and their charter to issue the same. They must also be financially sound and be willing and able to...

Effects of Print Publication Lag in Dual Format Journals on Scientometric Indicators

Science.gov (United States)

Heneberg, Petr

2013-01-01

Background Publication lag between manuscript submission and its final publication is considered as an important factor affecting the decision to submit, the timeliness of presented data, and the scientometric measures of the particular journal. Dual-format peer-reviewed journals (publishing both print and online editions of their content) adopted a broadly accepted strategy to shorten the publication lag: to publish the accepted manuscripts online ahead of their print editions, which may follow days, but also years later. Effects of this widespread habit on the immediacy index (average number of times an article is cited in the year it is published) calculation were never analyzed. Methodology/Principal Findings Scopus database (which contains nearly up-to-date documents in press, but does not reveal citations by these documents until they are finalized) was searched for the journals with the highest total counts of articles in press, or highest counts of articles in press appearing online in 2010–2011. Number of citations received by the articles in press available online was found to be nearly equal to citations received within the year when the document was assigned to a journal issue. Thus, online publication of in press articles affects severely the calculation of immediacy index of their source titles, and disadvantages online-only and print-only journals when evaluating them according to the immediacy index and probably also according to the impact factor and similar measures. Conclusions/Significance Caution should be taken when evaluating dual-format journals supporting long publication lag. Further research should answer the question, on whether the immediacy index should be replaced by an indicator based on the date of first publication (online or in print, whichever comes first) to eliminate the problems analyzed in this report. Information value of immediacy index is further questioned by very high ratio of authors’ self-citations among the

Title to mining properties

International Nuclear Information System (INIS)

Crouch, K.M.

1976-01-01

The requirements of the law which must be met in order to create title to an unpatented mining claim and the procedures which should be followed when an attempt is made to determine the title to the claim is acceptable are reviewed

Selecting suitable enclosures for digitally printed materials

International Nuclear Information System (INIS)

Burge, D; Rima, L

2010-01-01

It cannot be assumed that storage enclosures considered safe for traditionally printed images and documents are suitable for modern, digitally printed materials. In this project, a large variety of digital print types were tested using a modified version of the ISO 18916 Imaging materials-Processed imaging materials-Photographic activity test for enclosure materials standard to assess the risk to digital prints by paper enclosures known to be inert or reactive with traditional photographic prints. The types of enclosures tested included buffered and non-buffered cotton papers, and groundwood paper. In addition, qualitative filter paper that had been wetted and dried with either an acidic or basic solution was also tested to determine the effects of enclosure pH on digitally printed materials. It was determined that, in general, digital prints tended to be less reactive with various enclosure types than traditional prints. Digital prints were most sensitive to paper that contained groundwood. The enclosure reactivity test results were then integrated with previous published work on the tendencies of various enclosure types to abrade, ferrotype, or block to digital prints in order to create a comprehensive set of recommendations for digital print storage enclosures.

Inkjet printed electronics using copper nanoparticle ink

OpenAIRE

Kang, Jin Sung; Kim, Hak Sung; Ryu, Jongeun; Thomas Hahn, H.; Jang, Seonhee; Joung, Jae Woo

2010-01-01

Inkjet printing of electrode using copper nanoparticle ink is presented. Electrode was printed on a flexible glass epoxy composite substrate using drop on demand piezoelectric dispenser and was sintered at 200 °C of low temperature in N2 gas condition. The printed electrodes were made with various widths and thickness. In order to control the thickness of the printed electrode, number of printing was varied. Resistivity of printed electrode was calculated from the cross-sectional area measure...

Checking a printed board

CERN Multimedia

1977-01-01

An 'Interactive Printed Circuit Board Design System' has been developed by a company in a Member-State. Printed circuits are now produced at the SB's surface treatment workshop using a digitized photo-plotter.

3D Printing of Highly Stretchable, Shape-Memory, and Self-Healing Elastomer toward Novel 4D Printing.

Science.gov (United States)

Kuang, Xiao; Chen, Kaijuan; Dunn, Conner K; Wu, Jiangtao; Li, Vincent C F; Qi, H Jerry

2018-02-28

The three-dimensional (3D) printing of flexible and stretchable materials with smart functions such as shape memory (SM) and self-healing (SH) is highly desirable for the development of future 4D printing technology for myriad applications, such as soft actuators, deployable smart medical devices, and flexible electronics. Here, we report a novel ink that can be used for the 3D printing of highly stretchable, SM, and SH elastomer via UV-light-assisted direct-ink-write printing. An ink containing urethane diacrylate and a linear semicrystalline polymer is developed for the 3D printing of a semi-interpenetrating polymer network elastomer that can be stretched by up to 600%. The 3D-printed complex structures show interesting functional properties, such as high strain SM and SM -assisted SH capability. We demonstrate that such a 3D-printed SM elastomer has the potential application for biomedical devices, such as vascular repair devices. This research paves a new way for the further development of novel 4D printing, soft robotics, and biomedical devices.

High-resolution direct 3D printed PLGA scaffolds: print and shrink

International Nuclear Information System (INIS)

Chia, Helena N; Wu, Benjamin M

2015-01-01

Direct three-dimensional printing (3DP) produces the final part composed of the powder and binder used in fabrication. An advantage of direct 3DP is control over both the microarchitecture and macroarchitecture. Prints which use porogen incorporated in the powder result in high pore interconnectivity, uniform porosity, and defined pore size after leaching. The main limitations of direct 3DP for synthetic polymers are the use of organic solvents which can dissolve polymers used in most printheads and limited resolution due to unavoidable spreading of the binder droplet after contact with the powder. This study describes a materials processing strategy to eliminate the use of organic solvent during the printing process and to improve 3DP resolution by shrinking with a non-solvent plasticizer. Briefly, poly(lactic-co-glycolic acid) (PLGA) powder was prepared by emulsion solvent evaporation to form polymer microparticles. The printing powder was composed of polymer microparticles dry mixed with sucrose particles. After printing with a water-based liquid binder, the polymer microparticles were fused together to form a network by solvent vapor in an enclosed vessel. The sucrose is removed by leaching and the resulting scaffold is placed in a solution of methanol. The methanol acts as a non-solvent plasticizer and allows for polymer chain rearrangement and efficient packing of polymer chains. The resulting volumetric shrinkage is ∼80% at 90% methanol. A complex shape (honey-comb) was designed, printed, and shrunken to demonstrate isotropic shrinking with the ability to reach a final resolution of ∼400 μm. The effect of type of alcohol (i.e. methanol or ethanol), concentration of alcohol, and temperature on volumetric shrinking was studied. This study presents a novel materials processing strategy to overcome the main limitations of direct 3DP to produce high resolution PLGA scaffolds. (paper)

High-resolution direct 3D printed PLGA scaffolds: print and shrink.

Science.gov (United States)

Chia, Helena N; Wu, Benjamin M

2014-12-17

Direct three-dimensional printing (3DP) produces the final part composed of the powder and binder used in fabrication. An advantage of direct 3DP is control over both the microarchitecture and macroarchitecture. Prints which use porogen incorporated in the powder result in high pore interconnectivity, uniform porosity, and defined pore size after leaching. The main limitations of direct 3DP for synthetic polymers are the use of organic solvents which can dissolve polymers used in most printheads and limited resolution due to unavoidable spreading of the binder droplet after contact with the powder. This study describes a materials processing strategy to eliminate the use of organic solvent during the printing process and to improve 3DP resolution by shrinking with a non-solvent plasticizer. Briefly, poly(lactic-co-glycolic acid) (PLGA) powder was prepared by emulsion solvent evaporation to form polymer microparticles. The printing powder was composed of polymer microparticles dry mixed with sucrose particles. After printing with a water-based liquid binder, the polymer microparticles were fused together to form a network by solvent vapor in an enclosed vessel. The sucrose is removed by leaching and the resulting scaffold is placed in a solution of methanol. The methanol acts as a non-solvent plasticizer and allows for polymer chain rearrangement and efficient packing of polymer chains. The resulting volumetric shrinkage is ∼80% at 90% methanol. A complex shape (honey-comb) was designed, printed, and shrunken to demonstrate isotropic shrinking with the ability to reach a final resolution of ∼400 μm. The effect of type of alcohol (i.e. methanol or ethanol), concentration of alcohol, and temperature on volumetric shrinking was studied. This study presents a novel materials processing strategy to overcome the main limitations of direct 3DP to produce high resolution PLGA scaffolds.

INIS: Authority list for journal titles

International Nuclear Information System (INIS)

2005-01-01

This is the 31st revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13,104 journal titles, 2,078 regularly scanned journals and 561 key journals. It was last updated in February 2005. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part III, all journals that are regularly scanned by INIS Centers are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part IV, all journals that are regularly scanned by INIS Centers are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part V, all journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part VI, all journals are sorted alphabetically under their title. The name of the

INIS: Authority list for journal titles

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-03-01

This is the 31st revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13,104 journal titles, 2,078 regularly scanned journals and 561 key journals. It was last updated in February 2005. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part III, all journals that are regularly scanned by INIS Centers are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part IV, all journals that are regularly scanned by INIS Centers are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part V, all journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part VI, all journals are sorted alphabetically under their title. The name of the

INIS: Authority list for journal titles

International Nuclear Information System (INIS)

2006-01-01

This is the 32nd revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13,231 journal titles, 2,125 regularly scanned journals and 555 key journals. It was last updated in February 2006. The purpose of this report is to provide descriptive cataloguers with a standard entry for the full title of a journal. In addition to the full journal title, the ISSN (International Standard Serial Number), administered by the ISSN International Centre, Paris, France, and/or CODEN, assigned by Chemical Abstracts Service, USA, are given in this manual. In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part III, all journals that are regularly scanned by INIS Centres are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part IV, all journals that are regularly scanned by INIS Centres are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. In Part V, all journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. In Part VI, all journals are sorted alphabetically under their title. The name of the

3D Printing of Biosamples: A Concise Review

Science.gov (United States)

Zhao, Victoria Xin Ting; Wong, Ten It; Zhou, Xiaodong

This paper reviews the recent development of 3D printing of biosamples, in terms of the 3D structure design, suitable printing technology, and available materials. Successfully printed 3D biosamples should possess the properties of high cell viability, vascularization and good biocompatibility. These goals are attained by printing the materials of hydrogels, polymers and cells, with a carefully selected 3D printer from the categories of inkjet printing, extrusion printing and laser printing, based on the uniqueness, advantages and disadvantages of these technologies. For recent developments, we introduce the 3D applications of creating scaffolds, printing cells for self-assembly and testing platforms. We foresee more bio-applications of 3D printing will be developed, with the advancements on materials and 3D printing machines.

Automated Metadata Formatting for Cornell’s Print-on-Demand Books

Directory of Open Access Journals (Sweden)

Dianne Dietrich

2009-11-01

Full Text Available Cornell University Library has made Print-On Demand (POD books available for many of its digitized out-of-copyright books. The printer must be supplied with metadata from the MARC bibliographic record in order to produce book covers. Although the names of authors are present in MARC records, they are given in an inverted order suitable for alphabetical filing rather than the natural order that is desirable for book covers. This article discusses a process for parsing and manipulating the MARC author strings to identify their various component parts and to create natural order strings. In particular, the article focuses on processing non-name information in author strings, such as titles that were commonly used in older works, e.g., baron or earl, and suffixes appended to names, e.g., "of Bolsena." Relevant patterns are identified and a Python script is used to manipulate the author name strings.

3D Bio-Printing Review

Science.gov (United States)

Du, Xianbin

2018-01-01

Ultimate goal of tissue engineering is to replace pathological or necrotic body tissue or organ by artificial tissue or organ and tissue engineering is a very promising research field. 3D bio-printing is a kind of emerging technologies and a branch of tissue engineering. It has made significant progress in the past decade. 3D bio-printing can realize tissue and organ construction in vitro and has wide application in basic research and pharmacy. This paper is to make an analysis and review on 3D bio-printing from the perspectives of bioink, printing technology and technology application.

3D printing for dummies

CERN Document Server

Hausman, Kalani Kirk

2014-01-01

Get started printing out 3D objects quickly and inexpensively! 3D printing is no longer just a figment of your imagination. This remarkable technology is coming to the masses with the growing availability of 3D printers. 3D printers create 3-dimensional layered models and they allow users to create prototypes that use multiple materials and colors.  This friendly-but-straightforward guide examines each type of 3D printing technology available today and gives artists, entrepreneurs, engineers, and hobbyists insight into the amazing things 3D printing has to offer. You'll discover methods for

Fabrication of Capacitive Acoustic Resonators Combining 3D Printing and 2D Inkjet Printing Techniques

Directory of Open Access Journals (Sweden)

Rubaiyet Iftekharul Haque

2015-10-01

Full Text Available A capacitive acoustic resonator developed by combining three-dimensional (3D printing and two-dimensional (2D printed electronics technique is described. During this work, a patterned bottom structure with rigid backplate and cavity is fabricated directly by a 3D printing method, and then a direct write inkjet printing technique has been employed to print a silver conductive layer. A novel approach has been used to fabricate a diaphragm for the acoustic sensor as well, where the conductive layer is inkjet-printed on a pre-stressed thin organic film. After assembly, the resulting structure contains an electrically conductive diaphragm positioned at a distance from a fixed bottom electrode separated by a spacer. Measurements confirm that the transducer acts as capacitor. The deflection of the diaphragm in response to the incident acoustic single was observed by a laser Doppler vibrometer and the corresponding change of capacitance has been calculated, which is then compared with the numerical result. Observation confirms that the device performs as a resonator and provides adequate sensitivity and selectivity at its resonance frequency.

3D Printing: Print the future of ophthalmology.

Science.gov (United States)

Huang, Wenbin; Zhang, Xiulan

2014-08-26

The three-dimensional (3D) printer is a new technology that creates physical objects from digital files. Recent technological advances in 3D printing have resulted in increased use of this technology in the medical field, where it is beginning to revolutionize medical and surgical possibilities. It is already providing medicine with powerful tools that facilitate education, surgical planning, and organ transplantation research. A good understanding of this technology will be beneficial to ophthalmologists. The potential applications of 3D printing in ophthalmology, both current and future, are explored in this article. Copyright 2014 The Association for Research in Vision and Ophthalmology, Inc.

Application to printed resistors

International Nuclear Information System (INIS)

Hachiyanagi, Yoshimi; Uraki, Hisatsugu; Sawamura, Masashi

1989-01-01

Most of printed circuit boards are made at present by etching copper foils which are laminated on insulating composite boards of paper/phenol resin or glass nonwoven fabric/epoxy rein. This is called subtractive process, and since this is a wet process, the problem of coping with the pollution due to etching solution, plating solution and others is involved. As the method of solving this problem, attention has been paid to the dry process which forms conductor patterns by screen printing using electro-conductive paste. For such resin substrates, generally polymer thick films (PTF) using thermosetting resin as the binder are used. Also the research on the formation of resistors, condensers and other parts by printing using the technology of cermet thick films (CTF) and PTF is active, and it is partially put in practical use. The problems are the deformation and deterioration of substrates, therefore, as the countermeasures, electron beam hardening type PTF has been studied, and various pastes have been developed. In this paper, electron beam hardening type printed resistors are reported. The features, resistance paste, and a number of the experiments on printed resistors are described. (K.I.)

Inkjet-Printed Small-Molecule Organic Light-Emitting Diodes: Halogen-Free Inks, Printing Optimization, and Large-Area Patterning.

Science.gov (United States)

Zhou, Lu; Yang, Lei; Yu, Mengjie; Jiang, Yi; Liu, Cheng-Fang; Lai, Wen-Yong; Huang, Wei

2017-11-22

Manufacturing small-molecule organic light-emitting diodes (OLEDs) via inkjet printing is rather attractive for realizing high-efficiency and long-life-span devices, yet it is challenging. In this paper, we present our efforts on systematical investigation and optimization of the ink properties and the printing process to enable facile inkjet printing of conjugated light-emitting small molecules. Various factors on influencing the inkjet-printed film quality during the droplet generation, the ink spreading on the substrates, and its solidification processes have been systematically investigated and optimized. Consequently, halogen-free inks have been developed and large-area patterning inkjet printing on flexible substrates with efficient blue emission has been successfully demonstrated. Moreover, OLEDs manufactured by inkjet printing the light-emitting small molecules manifested superior performance as compared with their corresponding spin-cast counterparts.

Banner Pages on the New Printing Infrastructure

CERN Multimedia

2006-01-01

Changes to the printing service were announced in CERN Bulletin No. 37-38/2006. In the new infrastructure, the printing of the banner page has been disabled in order to reduce paper consumption. Statistics show that the average print job size is small and the paper savings by not printing the banner page could be up to 20 %. When each printer is moved onto the new infrastructure banner page printing will be disabled. In the case of corridor printers which are shared by several users, the Helpdesk can re-enable banner page printing upon request. We hope ultimately to arrive at a situation where banner page printing is enabled on fewer than 10% of printers registered on the network. You can still print banner pages on printers where it has been centrally disabled by using Linux. Simply add it to your print job on the client side by adding the -o job-sheets option to your lpr command. Detailed documentation is available on each SLC3/4 under the following link: http://localhost:631/sum.html#4_2 Please bea...

Balkan Print Forum – Dynamic Balkan Print Media Community

Directory of Open Access Journals (Sweden)

Rossitza Velkova

2011-11-01

Full Text Available Founded in October 2006, the Balkan Print Forum is gradually becoming an important regional institution. Its main targets are to share experiences and know-how,to initiate and intensify contacts and to support joint projects in the Balkan region.Since drupa 2008 there are 11 member countries of the Balkan Print Forum:Albania, Bosnia and Herzegovina, Bulgaria, Croatia, Former Yugoslav Republic of Macedonia, Greece, Hungary, Romania, Serbia, Slovenia and Turkey. Partners of BPF are some companies and universities from Russia and Ukraine.

7 CFR 1927.55 - Title clearance services.

Science.gov (United States)

2010-01-01

... REGULATIONS TITLE CLEARANCE AND LOAN CLOSING Real Estate Title Clearance and Loan Closing § 1927.55 Title clearance services. (a) Responsibilities of closing agents. Services to be provided to the agency and the borrower by a closing agent in connection with the transaction vary depending on whether a title insurance...

Active origami by 4D printing

International Nuclear Information System (INIS)

Ge, Qi; Qi, H Jerry; Dunn, Martin L; Dunn, Conner K

2014-01-01

Recent advances in three dimensional (3D) printing technology that allow multiple materials to be printed within each layer enable the creation of materials and components with precisely controlled heterogeneous microstructures. In addition, active materials, such as shape memory polymers, can be printed to create an active microstructure within a solid. These active materials can subsequently be activated in a controlled manner to change the shape or configuration of the solid in response to an environmental stimulus. This has been termed 4D printing, with the 4th dimension being the time-dependent shape change after the printing. In this paper, we advance the 4D printing concept to the design and fabrication of active origami, where a flat sheet automatically folds into a complicated 3D component. Here we print active composites with shape memory polymer fibers precisely printed in an elastomeric matrix and use them as intelligent active hinges to enable origami folding patterns. We develop a theoretical model to provide guidance in selecting design parameters such as fiber dimensions, hinge length, and programming strains and temperature. Using the model, we design and fabricate several active origami components that assemble from flat polymer sheets, including a box, a pyramid, and two origami airplanes. In addition, we directly print a 3D box with active composite hinges and program it to assume a temporary flat shape that subsequently recovers to the 3D box shape on demand. (paper)

Active origami by 4D printing

Science.gov (United States)

Ge, Qi; Dunn, Conner K.; Qi, H. Jerry; Dunn, Martin L.

2014-09-01

Recent advances in three dimensional (3D) printing technology that allow multiple materials to be printed within each layer enable the creation of materials and components with precisely controlled heterogeneous microstructures. In addition, active materials, such as shape memory polymers, can be printed to create an active microstructure within a solid. These active materials can subsequently be activated in a controlled manner to change the shape or configuration of the solid in response to an environmental stimulus. This has been termed 4D printing, with the 4th dimension being the time-dependent shape change after the printing. In this paper, we advance the 4D printing concept to the design and fabrication of active origami, where a flat sheet automatically folds into a complicated 3D component. Here we print active composites with shape memory polymer fibers precisely printed in an elastomeric matrix and use them as intelligent active hinges to enable origami folding patterns. We develop a theoretical model to provide guidance in selecting design parameters such as fiber dimensions, hinge length, and programming strains and temperature. Using the model, we design and fabricate several active origami components that assemble from flat polymer sheets, including a box, a pyramid, and two origami airplanes. In addition, we directly print a 3D box with active composite hinges and program it to assume a temporary flat shape that subsequently recovers to the 3D box shape on demand.

Inkjet and screen printing for electronic applications

OpenAIRE

Medina Rodríguez, Beatriz

2016-01-01

Printed electronics (PE) is a set of printing methods used to create electrical devices on various substrates. Printing typically uses common printing equipment suitable for defining patterns on material, such as screen printing, flexography, gravure, offset lithography, and inkjet. Electrically functional, electronic or optical inks are deposited on the substrate, creating active or passive devices. PE offers a great advantage when compared to traditional processes or microelectronics du...

Can lip prints provide biologic evidence?

Science.gov (United States)

Sharma, Preeti; Sharma, Neeraj; Wadhwan, Vijay; Aggarwal, Pooja

2016-01-01

Lip prints are unique and can be used in personal identification. Very few studies are available which establish them as biological evidence in the court of law. Thus, the objective of this study was to attempt to isolate DNA and obtain full short tandem repeat (STR) loci of the individual from the lip prints on different surfaces. Twelve lip prints were procured on different surfaces such as tissue paper, cotton cloth, ceramic tile, and glass surface. Latent lip prints were developed using fingerprint black powder. Lipstick-coated lip prints were also collected on the same supporting items. DNA was isolated, quantified, and amplified using Identifiler™ kit to type 15 STR loci. Ample quantity of DNA was extracted from all the lip print impressions and 15 loci were successfully located in seven samples. Fourteen loci were successfully typed in 3 lip impressions while 13 loci were typed in 2 samples. This study emphasizes the relevance of lip prints at the scene of crime. Extraction of DNA followed by typing of STR loci establishes the lip prints as biological evidence too. Tissue papers, napkins, cups, and glasses may have imprints of the suspect's lips. Thus, the full genetic profile is extremely useful for the forensic team.

3D printed e-tongue

Science.gov (United States)

Gaál, Gabriel; da Silva, Tatiana A.; Gaál, Vladimir; Hensel, Rafael C.; Amaral, Lucas R.; Rodrigues, Varlei; Riul, Antonio

2018-05-01

Nowadays, one of the biggest issues addressed to electronic sensor fabrication is the build-up of efficient electrodes as an alternative way to the expensive, complex and multistage processes required by traditional techniques. Printed electronics arises as an interesting alternative to fulfill this task due to the simplicity and speed to stamp electrodes on various surfaces. Within this context, the Fused Deposition Modeling 3D printing is an emerging, cost-effective and alternative technology to fabricate complex structures that potentiates several fields with more creative ideas and new materials for a rapid prototyping of devices. We show here the fabrication of interdigitated electrodes using a standard home-made CoreXY 3D printer using transparent and graphene-based PLA filaments. Macro 3D printed electrodes were easily assembled within 6 minutes with outstanding reproducibility. The electrodes were also functionalized with different nanostructured thin films via dip-coating Layer-by-Layer technique to develop a 3D printed e-tongue setup. As a proof of concept, the printed e-tongue was applied to soil analysis. A control soil sample was enriched with several macro-nutrients to the plants (N, P, K, S, Mg and Ca) and the discrimination was done by electrical impedance spectroscopy of water solution of the soil samples. The data was analyzed by Principal Component Analysis and the 3D printed sensor distinguished clearly all enriched samples despite the complexity of the soil chemical composition. The 3D printed e-tongue successfully used in soil analysis encourages further investments in developing new sensory tools for precision agriculture and other fields exploiting the simplicity and flexibility offered by the 3D printing techniques.

Plasma jet printing for flexible substrates

Energy Technology Data Exchange (ETDEWEB)

Gandhiraman, Ram P.; Singh, Eric; Diaz-Cartagena, Diana C.; Koehne, Jessica; Meyyappan, M. [Center for Nanotechnology, NASA Ames Research Center, Moffett Field, California 94035 (United States); Nordlund, Dennis [Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, Menlo Park, California 94025 (United States)

2016-03-21

Recent interest in flexible electronics and wearable devices has created a demand for fast and highly repeatable printing processes suitable for device manufacturing. Robust printing technology is critical for the integration of sensors and other devices on flexible substrates such as paper and textile. An atmospheric pressure plasma-based printing process has been developed to deposit different types of nanomaterials on flexible substrates. Multiwalled carbon nanotubes were deposited on paper to demonstrate site-selective deposition as well as direct printing without any type of patterning. Plasma-printed nanotubes were compared with non-plasma-printed samples under similar gas flow and other experimental conditions and found to be denser with higher conductivity. The utility of the nanotubes on the paper substrate as a biosensor and chemical sensor was demonstrated by the detection of dopamine, a neurotransmitter, and ammonia, respectively.

The NIH 3D Print Exchange: A Public Resource for Bioscientific and Biomedical 3D Prints

OpenAIRE

Coakley, Meghan F.; Hurt, Darrell E.; Weber, Nick; Mtingwa, Makazi; Fincher, Erin C.; Alekseyev, Vsevelod; Chen, David T.; Yun, Alvin; Gizaw, Metasebia; Swan, Jeremy; Yoo, Terry S.; Huyen, Yentram

2014-01-01

The National Institutes of Health (NIH) has launched the NIH 3D Print Exchange, an online portal for discovering and creating bioscientifically relevant 3D models suitable for 3D printing, to provide both researchers and educators with a trusted source to discover accurate and informative models. There are a number of online resources for 3D prints, but there is a paucity of scientific models, and the expertise required to generate and validate such models remains a barrier. The NIH 3D Print ...

Electron beam hardening type copper plate printing ink

International Nuclear Information System (INIS)

Kawamura, Eiji; Inoue, Mitsuo; Kusaki, Satoichiro

1989-01-01

Copper plate printing is the printing method of filling ink in the parts of concave printing elements on a type area, and transferring the ink to a base, and it is the feature that the ink in the printing element parts of a print rises. Copper plate prints show profound feeling, in addition, its effect of preventing forgery is high. This method is generally called engraving printing, and is used frequently for printing various bills and artistic prints. The electron beam irradiation apparatus installed in the laboratory of the Printing Bureau, Ministry of Finance, is an experimental machine of area beam type, and is so constructed as to do batch conveyance and web conveyance. As the ink in printing element parts rises, the offset at the delivery part of a printing machine becomes a problem. Electron beam is superior in its transparency, and can dry instantaneously to the inside of opaque ink. At 200 kV of acceleration voltage, the ink of copper plate prints can be hardened by electron beam irradiation. The dilution monomers as the vehicle for ink were tested for their dilution capability and the effect of electron beam hardening. The problem in the utilization of electron beam is the deterioration of papers, and the counter-measures were tested. (K.I.)

The use of an Ossis custom 3D-printed tri-flanged acetabular implant for major bone loss: minimum 2-year follow-up: Short title: Ossis custom 3D-Printed tri-flanged acetabular implant.

Science.gov (United States)

Kieser, David C; Ailabouni, Ramez; Kieser, Sandra C J; Wyatt, Michael C; Armour, Paul C; Coates, Mark H; Hooper, Gary J

2018-05-01

Custom 3D-printed acetabular implants are a new technology used in hip surgery with ever-increasing frequency. They offer patient-specific implants to optimise filling of bone defects and implant-bone contact, without the need for excessive bone resection. This is a retrospective cohort study of 46 consecutive patients who underwent an Ossis unilateral custom 3D-printed acetabular implant. Clinical (Oxford Hip Score OHS-60), Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC), Harris Hip Score (HHS) and radiological (restoration of biomechanical hip centre, osteointegration, wear, heterotrophic ossification) results were assessed. Patient mean age was 68 years and follow-up was 38 months (minimum 24 months). 10 patients were excluded from the outcome analysis; 2 patients died, 1 required revision for deep infection and 7 were lost to follow-up. Of the 36 patients included, 21 had severe osteolysis. 7 were revised for infection, 3 for tumoural defects, 3 for metallosis, 1 for dysplasia and 1 for trauma (Paprosky 2a [n=6], 2b [n=2], 2c [n=5], 3a [n=6], 3b [n=11], pelvic dissociation [n=6]). OHS significantly improved postoperatively (16-8-48.4 p=0.027). Postoperative functional scores were good (WOMAC 98; HHS 79). The biomechanical hip centre was restored in all patients. 1 patient had early implant migration with subsequent stabilisation. 2 patients had radiographs concerning for failure of osteointegration. 1 patient had recurrent dislocations. The mid-term results of the Ossis custom 3D-printed tri-flanged acetabular implant for the management of severe acetabular defects are encouraging. The improvement in functional scores and radiographic outcomes are comparable to similar designs. In addition, no cases have required revision for aseptic loosening.

National Ignition Facility Title II Design Plan

International Nuclear Information System (INIS)

Kumpan, S

1997-01-01

This National Ignition Facility (NIF) Title II Design Plan defines the work to be performed by the NIF Project Team between November 1996, when the U.S. Department of Energy (DOE) reviewed Title I design and authorized the initiation of Title H design and specific long-lead procurements, and September 1998, when Title 11 design will be completed

Customizing digital printing for fine art practice

Science.gov (United States)

Parraman, Carinna E.; Thirkell, Paul; Hoskins, Steve; Wang, Hong Qiang; Laidler, Paul

2005-01-01

The presentation will demonstrate how through alternative methods of digital print production the Centre for Fine Print Research (CFPR) is developing methodologies for digital printing that attempt to move beyond standard reproductive print methods. Profiling is used for input and output hardware, along with bespoke profiling for fine art printmaking papers. Examples of artist's work, and examples from the Perpetual Portfolio are included - an artist in residence scheme for selected artists wanting to work at the Centre and to make a large-format digital print. Colour is an important issue: colour fidelity, colour density on paper, colour that can be achieved through multiple-pass printing. Research is also underway to test colour shortfalls in the current inkjet ink range, and to extend colour through the use of traditional printing inks.

PRINTING TECHNIQUES: RECENT DEVELOPMENTS IN PHARMACEUTICAL TECHNOLOGY.

Science.gov (United States)

Jamroz, Witold; Kurek, Mateusz; Lyszczarz, Ewelina; Brniak, Witold; Jachowicz, Renata

2017-05-01

In the last few years there has been a huge progress in a development of printing techniques and their application in pharmaceutical sciences and particularly in the pharmaceutical technology. The variety of printing methods makes it necessary to systemize them, explain the principles of operation, and specify the possibilities of their use in pharmaceutical technology. This paper aims to review the printing techniques used in a drug development process. The growing interest in 2D and 3D printing methods results in continuously increasing number of scientific papers. Introduction of the first printed drug Spritam@ to the market seems to be a milestone of the 3D printing development. Thus, a particular aim of this review is to show the latest achievements of the researchers in the field of the printing medicines.

24 CFR 202.12 - Title II.

Science.gov (United States)

2010-04-01

... INSTITUTIONS AND MORTGAGEES Title I and Title II Specific Requirements § 202.12 Title II. (a) Tiered pricing—(1... rate up to two percentage points under the mortgagee's customary lending practices must be based on... after accounting for the value of servicing rights generated by making the loan and other income to the...

Influence of Parameters of a Printing Plate on Photoluminescence of Nanophotonic Printed Elements of Novel Packaging

Directory of Open Access Journals (Sweden)

Olha Sarapulova

2015-01-01

Full Text Available In order to produce nanophotonic elements for smart packaging, we investigated the influence of the parameters of screen and offset gravure printing plates on features of printed application of coatings with nanophotonic components and on parameters of their photoluminescence. To determine the dependence of luminescence intensity on the thickness of solid coating, we carried out the formation of nanophotonic solid surfaces by means of screen printing with different layer thickness on polypropylene film. The obtained analytical dependencies were used to confirm the explanation of the processes that occur during the fabrication of nanophotonic coverings with offset gravure printing plates. As a result of experimental studies, it was determined that the different character of the dependency of total luminescence intensity of nanophotonic elements from the percentage of a pad is explained by the use of different types of offset gravure printing plates, where the size of raster points remains constant in one case and changes in the other case, while the depth of the printing elements accordingly changes or remains constant. To obtain nanophotonic areas with predetermined photoluminescent properties, the influence of investigated factors on changes of photoluminescent properties of nanophotonic printed surfaces should be taken into consideration.

INIS: Authority list for journal titles

International Nuclear Information System (INIS)

2007-01-01

This is the 33rd revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13 396 journal titles, 2 170 regularly scanned journals and 578 key journals. It was last updated in February 2007. A journal - or periodical - is a continuing publication issued in a succession of discrete parts, usually bearing numbering and/or chronological designations and intended to be continued indefinitely. It is generally published within a defined, fixed interval between issues and normally appears more than once per year. It includes a mixture of articles, letters, summaries, etc. Within this definition, annuals such as the Annual Review of Nuclear Science are included, but series titles such as the McGraw-Hill Series in Nuclear Engineering are not. The purpose of this document is to provide descriptive cataloguers with standard elements to include in bibliographic level 'S' of the INIS record. These elements include field (tag) 229 (Full Journal Title), 320 (ISSN) and 321 (CODEN). The full journal title is mandatory, and either the ISSN or the CODEN must be included (both may appear). Instructions on how to use this and other elements of the INIS record format are found in INIS: Guide to Bibliographic Description (IAEA-INIS-1). In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: - In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. - In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. - In Part III, all journals that are regularly scanned by

3D-printed Bioanalytical Devices

Science.gov (United States)

Bishop, Gregory W; Satterwhite-Warden, Jennifer E; Kadimisetty, Karteek; Rusling, James F

2016-01-01

While 3D printing technologies first appeared in the 1980s, prohibitive costs, limited materials, and the relatively small number of commercially available printers confined applications mainly to prototyping for manufacturing purposes. As technologies, printer cost, materials, and accessibility continue to improve, 3D printing has found widespread implementation in research and development in many disciplines due to ease-of-use and relatively fast design-to-object workflow. Several 3D printing techniques have been used to prepare devices such as milli- and microfluidic flow cells for analyses of cells and biomolecules as well as interfaces that enable bioanalytical measurements using cellphones. This review focuses on preparation and applications of 3D-printed bioanalytical devices. PMID:27250897

Printing and civilization; Insatsu to bunmei

Energy Technology Data Exchange (ETDEWEB)

Takahashi, T. [Dainippon Ink and Chemicals Inc., Tokyo (Japan)

1995-01-01

It can be said that the printing has not been only a barometer of culture, but also has formed a foundation of culture as the facilities of civilization, and has shouldered a role to drag the culture. In modern nation, that the freedom of speech and press has been clearly pointed out as the fundamental human right, shows straightforwardly an important significance of such a printing. Though it is also statistically clear that there is an exact relation between GNP and printed materials per capita, in this paper centering around the examples in Japan, a relation between the printing and civilization/culture is introduced like the episodes. It does not yet become definite that what kind of influence a proposition so called `printing is a barometer of culture` is affected by the information/communication revolution which is regarded to be advanced very rapidly. However, speaking conclusively it can not be thought that a demand for the printing which can produce the information in a great deal of quantity with a low cost, and for the printing which does not need special output terminal and is excellent in portability and glance ability, may largely be reduced. 1 fig.

20 CFR 416.573 - How much will we withhold from your title II and title VIII benefits to recover a title XVI...

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false How much will we withhold from your title II... Payment of Benefits, Overpayments, and Underpayments § 416.573 How much will we withhold from your title...-due benefits. (b)(1) We will collect the overpayment from current monthly benefits due in a month by...

Natural fibre composites for 3D Printing

OpenAIRE

Pandey, Kapil

2015-01-01

3D printing has been common option for prototyping. Not all the materials are suitable for 3D printing. Various studies have been done and still many are ongoing regarding the suitability of the materials for 3D printing. This thesis work discloses the possibility of 3D printing of certain polymer composite materials. The main objective of this thesis work was to study the possibility for 3D printing the polymer composite material composed of natural fibre composite and various different ...

Active materials by four-dimension printing

Science.gov (United States)

Ge, Qi; Qi, H. Jerry; Dunn, Martin L.

2013-09-01

We advance a paradigm of printed active composite materials realized by directly printing glassy shape memory polymer fibers in an elastomeric matrix. We imbue the active composites with intelligence via a programmed lamina and laminate architecture and a subsequent thermomechanical training process. The initial configuration is created by three-dimension (3D) printing, and then the programmed action of the shape memory fibers creates time dependence of the configuration—the four-dimension (4D) aspect. We design and print laminates in thin plate form that can be thermomechanically programmed to assume complex three-dimensional configurations including bent, coiled, and twisted strips, folded shapes, and complex contoured shapes with nonuniform, spatially varying curvature. The original flat plate shape can be recovered by heating the material again. We also show how the printed active composites can be directly integrated with other printed functionalities to create devices; here we demonstrate this by creating a structure that can assemble itself.

Printing versus coating - What will be the future production technology for printed electronics?

Energy Technology Data Exchange (ETDEWEB)

Glawe, Andrea; Eggerath, Daniel; Schäfer, Frank [KROENERT GmbH and Co KG, Schuetzenstrasse 105, 22761 Hamburg (Germany)

2015-02-17

The market of Large Area Organic Printed Electronics is developing rapidly to increase efficiency and quality as well as to lower costs further. Applications for OPV, OLED, RFID and compact Printed Electronic systems are increasing. In order to make the final products more affordable, but at the same time highly accurate, Roll to Roll (R2R) production on flexible transparent polymer substrates is the way forward. There are numerous printing and coating technologies suitable depending on the design, the product application and the chemical process technology. Mainly the product design (size, pattern, repeatability) defines the application technology.

Detection of latent prints by Raman imaging

Science.gov (United States)

Lewis, Linda Anne [Andersonville, TN; Connatser, Raynella Magdalene [Knoxville, TN; Lewis, Sr., Samuel Arthur

2011-01-11

The present invention relates to a method for detecting a print on a surface, the method comprising: (a) contacting the print with a Raman surface-enhancing agent to produce a Raman-enhanced print; and (b) detecting the Raman-enhanced print using a Raman spectroscopic method. The invention is particularly directed to the imaging of latent fingerprints.

INIS: Authority list for journal titles

International Nuclear Information System (INIS)

2008-01-01

This is the 34th revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13 538 journal titles, 2 106 regularly scanned journals and 613 key journals. It was last updated in February 2008. A journal - or periodical - is a continuing publication issued in a succession of discrete parts, usually bearing numbering and/or chronological designations and intended to be continued indefinitely. It is generally published within a defined, fixed interval between issues and normally appears more than once per year. It includes a mixture of articles, letters, summaries, etc. Within this definition, annuals such as the Annual Review of Nuclear Science are included, but series titles such as the McGraw-Hill Series in Nuclear Engineering are not. The purpose of this document is to provide descriptive cataloguers with standard elements to include in bibliographic level 'S' of the INIS record. These elements include field (tag) 229 (Full Journal Title), 320 (ISSN) and 321 (CODEN). The full journal title is mandatory, and either the ISSN or the CODEN must be included (both may appear). Instructions on how to use this and other elements of the INIS record format are found in INIS: Guide to Bibliographic Description (IAEA-INIS-1). In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: - In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. - In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. - In Part III, all journals that are regularly scanned by

Colour print workflow and methods for multilayering of colour and decorative inks using UV inkjet for fine art printing

Science.gov (United States)

Parraman, Carinna

2012-01-01

In order to increase density of colour and improve ink coverage when printing onto a range of non standard substrates, this paper will present research into multi-layering of colour and the appearance of colour at 'n' levels of ink coverage. Returning to our original investigation of artist's requirements when making inkjet prints, these observations are based on empirical approaches that address the need to present physical data that is more useful and meaningful to the designer. The study has used multi-pass printed colour charts to measure colour and to provide users with an understanding at a soft-preview level to demonstrate the appearance of printed colour on different substrates. Test results relating to the appearance of print on different surfaces, and a series of case studies will be presented using recent research into the capabilities of UV printing technology, which has widened the opportunities for the designer to print onto non-standard materials. It will also present a study into layering of greys and gloss in order to improve the appearance of printed images onto metal.

The influence of printing substrate on macro non-uniformity and line reproduction quality of imprints printed with electrophotographic process

Directory of Open Access Journals (Sweden)

Đorđe Vujčić

2016-12-01

Full Text Available Print quality is very important for every printing technique. It depends on many different quality attributes. This research included analysis of macro non-uniformities and line reproduction. 16 different paper substrates printed by electrophotographic process were analyzed. They were separated in two groups: coated and uncoated papers. Analysis of macro non-uniformity showed that print mottle has lower values when printed on coated papers than on uncoated papers. Line reproduction analysis showed that the toner spreaded, during melting and fixation, on line edges for both types of paper. According to these results it can be concluded that paper substrate affects the macro non-uniformity and line reproduction, thus overall print quality.

Reprocessable thermosets for sustainable three-dimensional printing.

Science.gov (United States)

Zhang, Biao; Kowsari, Kavin; Serjouei, Ahmad; Dunn, Martin L; Ge, Qi

2018-05-08

Among all three-dimensional (3D) printing materials, thermosetting photopolymers claim almost half of the market, and have been widely used in various fields owing to their superior mechanical stability at high temperatures, excellent chemical resistance as well as good compatibility with high-resolution 3D printing technologies. However, once these thermosetting photopolymers form 3D parts through photopolymerization, the covalent networks are permanent and cannot be reprocessed, i.e., reshaped, repaired, or recycled. Here, we report a two-step polymerization strategy to develop 3D printing reprocessable thermosets (3DPRTs) that allow users to reform a printed 3D structure into a new arbitrary shape, repair a broken part by simply 3D printing new material on the damaged site, and recycle unwanted printed parts so the material can be reused for other applications. These 3DPRTs provide a practical solution to address environmental challenges associated with the rapid increase in consumption of 3D printing materials.

Concept of heat-induced inkless eco-printing.

Science.gov (United States)

Chen, Jinxiang; Wang, Yong; Xie, Juan; Meng, Chuang; Wu, Gang; Zu, Qiao

2012-07-01

Existing laser and inkjet printers often produce adverse effects on human health, the recycling of printing paper and the environment. Therefore, this paper examines the thermogravimetry curves for printer paper, analyzes the discoloration of paper using heat-induction, and investigates the relationship between paper discoloration and the heat-inducing temperature. The mechanism of heat-induced printing is analyzed initially, and its feasibility is determined by a comparative analysis of heat-induced (laser ablation) printing and commercial printing. The innovative concept of heat-induced inkless eco-printing is proposed, in which the required text or graphics are formed on the printing paper via yellowing and blackening produced by thermal energy. This process does not require ink during the printing process; thus, it completely eliminates the aforementioned health and environmental issues. This research also contributes to related interdisciplinary research in biology, laser technology, photochemistry, nano-science, paper manufacturing and color science. Copyright © 2012 Elsevier Ltd. All rights reserved.

Land Titles and Rice Production in Vietnam

DEFF Research Database (Denmark)

Van Den Broeck, Katleen; Newman, Carol; Tarp, Finn

In most of the empirical literature on land titling, the household is regarded as unitary, and land rights are found to have ambiguous effects on land allocation, investment and productivity. Using data from 12 provinces in Vietnam, we diversify land titles, and show in a household fixed effects...... analysis of plot level rice yields that land titles are indeed important. Only exclusively held titles have the expected positive effects, and the positive effect on yields is found in male headed households. Furthermore, a household level rice yield function reveals that exclusive user rights...... are inefficiency decreasing, while jointly held user rights have no efficiency effects. Finally, once the gender of the head of household is controlled for, exclusively held female titles have a greater positive effect on the efficiency of the household than that of male held titles...

Print like an Egyptian.

Science.gov (United States)

Weisensee, Marilyn

1990-01-01

Describes a relief printmaking unit for sixth graders with the objective of decorating the inside of a pyramid. Ancient Egyptian imagery was used to help students become familiar with the style. Students designed and printed linoleum prints in different colors. They then critiqued their work and made their selection for the pyramid. (KM)

Medical 3D Printing for the Radiologist

Science.gov (United States)

Mitsouras, Dimitris; Liacouras, Peter; Imanzadeh, Amir; Giannopoulos, Andreas A.; Cai, Tianrun; Kumamaru, Kanako K.; George, Elizabeth; Wake, Nicole; Caterson, Edward J.; Pomahac, Bohdan; Ho, Vincent B.; Grant, Gerald T.

2015-01-01

While use of advanced visualization in radiology is instrumental in diagnosis and communication with referring clinicians, there is an unmet need to render Digital Imaging and Communications in Medicine (DICOM) images as three-dimensional (3D) printed models capable of providing both tactile feedback and tangible depth information about anatomic and pathologic states. Three-dimensional printed models, already entrenched in the nonmedical sciences, are rapidly being embraced in medicine as well as in the lay community. Incorporating 3D printing from images generated and interpreted by radiologists presents particular challenges, including training, materials and equipment, and guidelines. The overall costs of a 3D printing laboratory must be balanced by the clinical benefits. It is expected that the number of 3D-printed models generated from DICOM images for planning interventions and fabricating implants will grow exponentially. Radiologists should at a minimum be familiar with 3D printing as it relates to their field, including types of 3D printing technologies and materials used to create 3D-printed anatomic models, published applications of models to date, and clinical benefits in radiology. Online supplemental material is available for this article. ©RSNA, 2015 PMID:26562233

Medical 3D Printing for the Radiologist.

Science.gov (United States)

Mitsouras, Dimitris; Liacouras, Peter; Imanzadeh, Amir; Giannopoulos, Andreas A; Cai, Tianrun; Kumamaru, Kanako K; George, Elizabeth; Wake, Nicole; Caterson, Edward J; Pomahac, Bohdan; Ho, Vincent B; Grant, Gerald T; Rybicki, Frank J

2015-01-01

While use of advanced visualization in radiology is instrumental in diagnosis and communication with referring clinicians, there is an unmet need to render Digital Imaging and Communications in Medicine (DICOM) images as three-dimensional (3D) printed models capable of providing both tactile feedback and tangible depth information about anatomic and pathologic states. Three-dimensional printed models, already entrenched in the nonmedical sciences, are rapidly being embraced in medicine as well as in the lay community. Incorporating 3D printing from images generated and interpreted by radiologists presents particular challenges, including training, materials and equipment, and guidelines. The overall costs of a 3D printing laboratory must be balanced by the clinical benefits. It is expected that the number of 3D-printed models generated from DICOM images for planning interventions and fabricating implants will grow exponentially. Radiologists should at a minimum be familiar with 3D printing as it relates to their field, including types of 3D printing technologies and materials used to create 3D-printed anatomic models, published applications of models to date, and clinical benefits in radiology. Online supplemental material is available for this article. (©)RSNA, 2015.

Photooxidation stability of microcapsules in thermochromic prints

Directory of Open Access Journals (Sweden)

Mirela Rozic

2018-03-01

Full Text Available In this paper, photochemical stability of two thermochromic prints was investigated: vegetable oil based offset and UV curing screen printing ink. The obtained preliminary results can be used for further detailed examination of prints stability. It is well known that thermochromic printing inks are very unstabile when exsposed to UV irradiance and this is why they are mainly used for applications that are not directly exposed to sunlight. The results of the study show the heterogeneous nature of photooxidative degradation of thermochromic prints, and the opposite behaviour of photooxidation can be noticed comparing examined prints. Microcapsules in the UV curable screen print by fixation with polar polymer binder can create a new products stable to photoxidation. For this reason, the areas where the microcapsules and binder are bonded together are stable. Degraded only areas where binder is not related to microcapsules. Microcapsules in offset print do not have the ability to create new stabile forms due to smaller polarity and different chemical composition of the offset oxidized binder. In the offset print, the microcapsules are the least photooxidative stable and also cause lower photooxidative stability of the binder in contact with them. Cavities are formed in the areas where microcapsules are in contact with the binder, while the areas in which the binder is not in contact with microcapsules are not degraded.

Make or Buy: An Analysis of the Impacts of 3D Printing Operations, 3D Laser Scanning Technology, and Collaborative Product Life-Cycle Management on Ship Maintenance and Modernization Cost Savings

Science.gov (United States)

2015-04-30

ååì~ä=^Åèìáëáíáçå= oÉëÉ~êÅÜ=póãéçëáìã= tÉÇåÉëÇ~ó=pÉëëáçåë= sçäìãÉ=f= = Make or Buy: An Analysis of the Impacts of 3D Printing Operations, 3D Laser...COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE Make or Buy: An Analysis of the Impacts of 3D Printing Operations, 3D Laser Scanning...Åèìáëáíáçå=oÉëÉ~êÅÜ=mêçÖê~ãW= `êÉ~íáåÖ=póåÉêÖó=Ñçê=fåÑçêãÉÇ=`Ü~åÖÉ= - 182 - Make or Buy: An Analysis of the Impacts of 3D Printing Operations, 3D Laser

All-printed capacitors with continuous solution dispensing technology

Science.gov (United States)

Ge, Yang; Plötner, Matthias; Berndt, Andreas; Kumar, Amit; Voit, Brigitte; Pospiech, Doris; Fischer, Wolf-Joachim

2017-09-01

Printed electronics have been introduced into the commercial markets in recent years. Various printing technologies have emerged aiming to process printed electronic devices with low cost, environmental friendliness, and compatibility with large areas and flexible substrates. The aim of this study is to propose a continuous solution dispensing technology for processing all-printed thin-film capacitors on glass substrates using a leading-edge printing instrument. Among all printing technologies, this study provides concrete proof of the following outstanding advantages of this technology: high tolerance to inks, high throughput, low cost, and precise pattern transfers. Ag nanoparticle ink based on glycol ethers was used to print the electrodes. To obtain dielectric ink, a copolymer powder of poly(methyl methacrylate-co-benzoylphenyl methacrylate) containing crosslinkable side groups was dissolved in anisole. Various layouts were designed to support multiple electronic applications. Scanning electron microscopy and atomic force microscopy were used to investigate the all-printed capacitor layers formed using the proposed process. Additionally, the printed capacitors were electrically characterized under direct current and alternating current. The measured electrical properties of the printed capacitors were consistent with the theoretical results.

Influence of Parameters of a Printing Plate on Photoluminescence of Nano photonic Printed Elements of Novel Packaging

International Nuclear Information System (INIS)

Sarapulova, O.; Sherstiuk, V.

2015-01-01

In order to produce nano photonic elements for smart packaging, we investigated the influence of the parameters of screen and offset gravure printing plates on features of printed application of coatings with nano photonic components and on parameters of their photoluminescence. To determine the dependence of luminescence intensity on the thickness of solid coating, we carried out the formation of nano photonic solid surfaces by means of screen printing with different layer thickness on polypropylene film. The obtained analytical dependencies were used to confirm the explanation of the processes that occur during the fabrication of nano photonic coverings with offset gravure printing plates. As a result of experimental studies, it was determined that the different character of the dependency of total luminescence intensity of nano photonic elements from the percentage of a pad is explained by the use of different types of offset gravure printing plates, where the size of raster points remains constant in one case and changes in the other case, while the depth of the printing elements accordingly changes or remains constant. To obtain nano photonic areas with predetermined photo luminescent properties, the influence of investigated factors on changes of photo luminescent properties of nano photonic printed surfaces should be taken into consideration

Review of Recent Inkjet-Printed Capacitive Tactile Sensors

Directory of Open Access Journals (Sweden)

Ahmed Salim

2017-11-01

Full Text Available Inkjet printing is an advanced printing technology that has been used to develop conducting layers, interconnects and other features on a variety of substrates. It is an additive manufacturing process that offers cost-effective, lightweight designs and simplifies the fabrication process with little effort. There is hardly sufficient research on tactile sensors and inkjet printing. Advancements in materials science and inkjet printing greatly facilitate the realization of sophisticated tactile sensors. Starting from the concept of capacitive sensing, a brief comparison of printing techniques, the essential requirements of inkjet-printing and the attractive features of state-of-the art inkjet-printed tactile sensors developed on diverse substrates (paper, polymer, glass and textile are presented in this comprehensive review. Recent trends in inkjet-printed wearable/flexible and foldable tactile sensors are evaluated, paving the way for future research.

Experiments on Printed Intelligence and Its Applications

OpenAIRE

Barbonelova, Angelina

2015-01-01

Printed intelligence technology refers to products and systems that are produced using traditional printing methods and that are able to communicate or react with the user, environment or other products and systems. The technology provides the foundations of innovative products such as printed OLEDs (organic light emitting device), electroluminescent displays, organic photovoltaics, thin film batteries and disposable sensors. This study presents research on different printing techniques i...

Future of printing: changes and challenges, technologies and markets

Science.gov (United States)

Kipphan, Helmut

1998-01-01

Digitalization within the graphic arts industry is described and it is explained how it is improving and changing the print production strategies and which new kinds of print production systems are developed or can be expected. The relationship of printed media and electronic media is analyzed and a positioning for the next century is given. The state of the art of conventional printing technologies, especially using direct imagine techniques, and their position within the digital workflow are shortly described. Non-impact printing multicolor printing systems are explained, based on general design criteria and linked to existing and newly announced equipment. The use of high-tech components for building up successful systems with high reliability, high quality and low production costs is included with some examples. Digital printing systems open many opportunities in print production: distributed printing, personalization, print and book on demand are explained as examples. The overview of the several printing technologies and their positioning regarding quality and productivity leads to the scenario about the important position of printed media, also in the distant future.

Functional electronic screen printing – electroluminescent smart fabric watch

OpenAIRE

de Vos, Marc; Torah, Russel; Beeby, Steve; Tudor, John

2013-01-01

Motivation for screen printed smart fabrics.Introduce functional electronic screen printing on fabrics.Printed smart fabric watch design.Printing process for electroluminescent watch.Demonstration video.Conclusions and further work.Examples of other screen printed smart fabrics.

Contextual advertisement placement in printed media

Science.gov (United States)

Liu, Sam; Joshi, Parag

2010-02-01

Advertisements today provide the necessary revenue model supporting the WWW ecosystem. Targeted or contextual ad insertion plays an important role in optimizing the financial return of this model. Nearly all the current ads that appear on web sites are geared for display purposes such as banner and "pay-per-click". Little attention, however, is focused on deriving additional ad revenues when the content is repurposed for alternative mean of presentation, e.g. being printed. Although more and more content is moving to the Web, there are still many occasions where printed output of web content is desirable, such as maps and articles; thus printed ad insertion can potentially be lucrative. In this paper, we describe a contextual ad insertion network aimed to realize new revenue for print service providers for web printing. We introduce a cloud print service that enables contextual ads insertion, with respect to the main web page content, when a printout of the page is requested. To encourage service utilization, it would provide higher quality printouts than what is possible from current browser print drivers, which generally produce poor outputs, e.g. ill formatted pages. At this juncture we will limit the scope to only article-related web pages although the concept can be extended to arbitrary web pages. The key components of this system include (1) the extraction of article from web pages, (2) the extraction of semantics from article, (3) querying the ad database for matching advertisement or coupon, and (4) joint content and ad layout for print outputs.

All-printed paper memory

KAUST Repository

Lien, Derhsien

2014-08-26

We report the memory device on paper by means of an all-printing approach. Using a sequence of inkjet and screen-printing techniques, a simple metal-insulator-metal device structure is fabricated on paper as a resistive random access memory with a potential to reach gigabyte capacities on an A4 paper. The printed-paper-based memory devices (PPMDs) exhibit reproducible switching endurance, reliable retention, tunable memory window, and the capability to operate under extreme bending conditions. In addition, the PBMD can be labeled on electronics or living objects for multifunctional, wearable, on-skin, and biocompatible applications. The disposability and the high-security data storage of the paper-based memory are also demonstrated to show the ease of data handling, which are not achievable for regular silicon-based electronic devices. We envision that the PPMDs manufactured by this cost-effective and time-efficient all-printing approach would be a key electronic component to fully activate a paper-based circuit and can be directly implemented in medical biosensors, multifunctional devices, and self-powered systems. © 2014 American Chemical Society.

Quarterly title list for the period ending June 1980

International Nuclear Information System (INIS)

1980-01-01

The title list contains: a) 17 titles and abstracts of laboratory reports, b) 36 titles of publications (32 with abstracts), c) 13 titles of articles submitted for publication (12 with abstracts), and d) 72 titles of lectures (52 with abstracts.) (GG) [de

40 CFR 63.824 - Standards: Publication rotogravure printing.

Science.gov (United States)

2010-07-01

... (CONTINUED) National Emission Standards for the Printing and Publishing Industry § 63.824 Standards: Publication rotogravure printing. (a) Each owner or operator of any publication rotogravure printing affected... printing. 63.824 Section 63.824 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR...

Title of the paper goes here second line

Indian Academy of Sciences (India)

%%Please download if these packages are not included %%in your local TeX distribution %%txfonts,balance,textcase,float %% \\begin{document} %%paper title %%For line breaks, \\\\ can be used within title \\title{Title of the paper goes here\\\\ second line} %%author names are separated by comma (,) %%use \\and before ...

Printing Ancient Terracotta Warriors

Science.gov (United States)

Gadecki, Victoria L.

2010-01-01

Standing in awe in Xian, China, at the Terra Cotta warrior archaeological site, the author thought of sharing this experience and excitement with her sixth-grade students. She decided to let her students carve patterns of the ancient soldiers to understand their place in Chinese history. They would make block prints and print multiple soldiers on…

FUTURE SCOPE OF WOMEN CARRIER IN THE PRINTING INDUSTRY: THE CHALLENGES OF WOMEN IN PRINTING OGANIZATIONS (A SURVEY OF TWENTY FIVE COMPANIES "SMALL, MEDIUM AND LARGE PRINTING ORGANIZATION" IN AREA "NCR DELHI AND HISAR, HR".)

OpenAIRE

Mr. Azad Singh*

2017-01-01

Women carrier in printing organization today, printing industry is growing with an expositional rate & required skills manpower. In this survey based paper to getting recruit of women 10%small, 30%medium and 60% large scale print industry. Objective of this paper is too filled out manpower skills printing industries are seaking in B.Tech women printing students to bridge the gap between skills and required in printing organization. A survey 25 companies was carried out. the result indicated t...

Three-Dimensionally Printed Micro-electromechanical Switches.

Science.gov (United States)

Lee, Yongwoo; Han, Jungmin; Choi, Bongsik; Yoon, Jinsu; Park, Jinhee; Kim, Yeamin; Lee, Jieun; Kim, Dae Hwan; Kim, Dong Myong; Lim, Meehyun; Kang, Min-Ho; Kim, Sungho; Choi, Sung-Jin

2018-05-09

Three-dimensional (3D) printers have attracted considerable attention from both industry and academia and especially in recent years because of their ability to overcome the limitations of two-dimensional (2D) processes and to enable large-scale facile integration techniques. With 3D printing technologies, complex structures can be created using only a computer-aided design file as a reference; consequently, complex shapes can be manufactured in a single step with little dependence on manufacturer technologies. In this work, we provide a first demonstration of the facile and time-saving 3D printing of two-terminal micro-electromechanical (MEM) switches. Two widely used thermoplastic materials were used to form 3D-printed MEM switches; freely suspended and fixed electrodes were printed from conductive polylactic acid, and a water-soluble sacrificial layer for air-gap formation was printed from poly(vinyl alcohol). Our 3D-printed MEM switches exhibit excellent electromechanical properties, with abrupt switching characteristics and an excellent on/off current ratio value exceeding 10 6 . Therefore, we believe that our study makes an innovative contribution with implications for the development of a broader range of 3D printer applications (e.g., the manufacturing of various MEM devices and sensors), and the work highlights a uniquely attractive path toward the realization of 3D-printed electronics.

Scalable, full-colour and controllable chromotropic plasmonic printing

Science.gov (United States)

Xue, Jiancai; Zhou, Zhang-Kai; Wei, Zhiqiang; Su, Rongbin; Lai, Juan; Li, Juntao; Li, Chao; Zhang, Tengwei; Wang, Xue-Hua

2015-01-01

Plasmonic colour printing has drawn wide attention as a promising candidate for the next-generation colour-printing technology. However, an efficient approach to realize full colour and scalable fabrication is still lacking, which prevents plasmonic colour printing from practical applications. Here we present a scalable and full-colour plasmonic printing approach by combining conjugate twin-phase modulation with a plasmonic broadband absorber. More importantly, our approach also demonstrates controllable chromotropic capability, that is, the ability of reversible colour transformations. This chromotropic capability affords enormous potentials in building functionalized prints for anticounterfeiting, special label, and high-density data encryption storage. With such excellent performances in functional colour applications, this colour-printing approach could pave the way for plasmonic colour printing in real-world commercial utilization. PMID:26567803

Effect of print layer height and printer type on the accuracy of 3-dimensional printed orthodontic models.

Science.gov (United States)

Favero, Christian S; English, Jeryl D; Cozad, Benjamin E; Wirthlin, John O; Short, Megan M; Kasper, F Kurtis

2017-10-01

Three-dimensional (3D) printing technologies enable production of orthodontic models from digital files; yet a range of variables associated with the process could impact the accuracy and clinical utility of the models. The objective of this study was to investigate the effect of print layer height on the accuracy of orthodontic models printed 3 dimensionally using a stereolithography format printer and to compare the accuracy of orthodontic models fabricated with several commercially available 3D printers. Thirty-six identical models were produced with a stereolithography-based 3D printer using 3 layer heights (n = 12 per group): 25, 50, and 100 μm. Forty-eight additional models were printed using 4 commercially available 3D printers (n = 12 per group). Each printed model was digitally scanned and compared with the input file via superimposition analysis using a best-fit algorithm to assess accuracy. Statistically significant differences were found in the average overall deviations of models printed at each layer height, with the 25-μm and 100-μm layer height groups having the greatest and least deviations, respectively. Statistically significant differences were also found in the average overall deviations of models produced using the various 3D printer models, but all values fell within clinically acceptable limits. The print layer height and printer model can affect the accuracy of a 3D printed orthodontic model, but the impact should be considered with respect to the clinical tolerances associated with the envisioned application. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Templated Dry Printing of Conductive Metal Nanoparticles

Science.gov (United States)

Rolfe, David Alexander

Printed electronics can lower the cost and increase the ubiquity of electrical components such as batteries, sensors, and telemetry systems. Unfortunately, the advance of printed electronics has been held back by the limited minimum resolution, aspect ratio, and feature fidelity of present printing techniques such as gravure, screen printing and inkjet printing. Templated dry printing offers a solution to these problems by patterning nanoparticle inks into templates before drying. This dissertation shows advancements in two varieties of templated dry nanoprinting. The first, advective micromolding in vapor-permeable templates (AMPT) is a microfluidic approach that uses evaporation-driven mold filling to create submicron features with a 1:1 aspect ratio. We will discuss submicron surface acoustic wave (SAW) resonators made through this process, and the refinement process in the template manufacturing process necessary to make these devices. We also present modeling techniques that can be applied to future AMPT templates. We conclude with a modified templated dry printing that improves throughput and isolated feature patterning by transferring dry-templated features with laser ablation. This method utilizes surface energy-defined templates to pattern features via doctor blade coating. Patterned and dried features can be transferred to a polymer substrate with an Nd:YAG MOPA fiber laser, and printed features can be smaller than the laser beam width.

Digital Dentistry — 3D Printing Applications

Directory of Open Access Journals (Sweden)

Zaharia Cristian

2017-03-01

Full Text Available Three-dimensional (3D printing is an additive manufacturing method in which a 3D item is formed by laying down successive layers of material. 3D printers are machines that produce representations of objects either planned with a CAD program or scanned with a 3D scanner. Printing is a method for replicating text and pictures, typically with ink on paper. We can print different dental pieces using different methods such as selective laser sintering (SLS, stereolithography, fused deposition modeling, and laminated object manufacturing. The materials are certified for printing individual impression trays, orthodontic models, gingiva mask, and different prosthetic objects. The material can reach a flexural strength of more than 80 MPa. 3D printing takes the effectiveness of digital projects to the production phase. Dental laboratories are able to produce crowns, bridges, stone models, and various orthodontic appliances by methods that combine oral scanning, 3D printing, and CAD/CAM design. Modern 3D printing has been used for the development of prototypes for several years, and it has begun to find its use in the world of manufacturing. Digital technology and 3D printing have significantly elevated the rate of success in dental implantology using custom surgical guides and improving the quality and accuracy of dental work.

Advances and Future Challenges in Printed Batteries.

Science.gov (United States)

Sousa, Ricardo E; Costa, Carlos M; Lanceros-Méndez, Senentxu

2015-11-01

There is an increasing interest in thin and flexible energy storage devices to meet modern society's needs for applications such as radio frequency sensing, interactive packaging, and other consumer products. Printed batteries comply with these requirements and are an excellent alternative to conventional batteries for many applications. Flexible and microbatteries are also included in the area of printed batteries when fabricated using printing technologies. The main characteristics, advantages, disadvantages, developments, and printing techniques of printed batteries are presented and discussed in this Review. The state-of-the-art takes into account both the research and industrial levels. On the academic level, the research progress of printed batteries is divided into lithium-ion and Zn-manganese dioxide batteries and other battery types, with emphasis on the different materials for anode, cathode, and separator as well as in the battery design. With respect to the industrial state-of-the-art, materials, device formulations, and manufacturing techniques are presented. Finally, the prospects and challenges of printed batteries are discussed. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

3D Printed Bionic Nanodevices

Science.gov (United States)

Kong, Yong Lin; Gupta, Maneesh K.; Johnson, Blake N.; McAlpine, Michael C.

2016-01-01

Summary The ability to three-dimensionally interweave biological and functional materials could enable the creation of bionic devices possessing unique and compelling geometries, properties, and functionalities. Indeed, interfacing high performance active devices with biology could impact a variety of fields, including regenerative bioelectronic medicines, smart prosthetics, medical robotics, and human-machine interfaces. Biology, from the molecular scale of DNA and proteins, to the macroscopic scale of tissues and organs, is three-dimensional, often soft and stretchable, and temperature sensitive. This renders most biological platforms incompatible with the fabrication and materials processing methods that have been developed and optimized for functional electronics, which are typically planar, rigid and brittle. A number of strategies have been developed to overcome these dichotomies. One particularly novel approach is the use of extrusion-based multi-material 3D printing, which is an additive manufacturing technology that offers a freeform fabrication strategy. This approach addresses the dichotomies presented above by (1) using 3D printing and imaging for customized, hierarchical, and interwoven device architectures; (2) employing nanotechnology as an enabling route for introducing high performance materials, with the potential for exhibiting properties not found in the bulk; and (3) 3D printing a range of soft and nanoscale materials to enable the integration of a diverse palette of high quality functional nanomaterials with biology. Further, 3D printing is a multi-scale platform, allowing for the incorporation of functional nanoscale inks, the printing of microscale features, and ultimately the creation of macroscale devices. This blending of 3D printing, novel nanomaterial properties, and ‘living’ platforms may enable next-generation bionic systems. In this review, we highlight this synergistic integration of the unique properties of nanomaterials with

3D Printed Bionic Nanodevices.

Science.gov (United States)

Kong, Yong Lin; Gupta, Maneesh K; Johnson, Blake N; McAlpine, Michael C

2016-06-01

The ability to three-dimensionally interweave biological and functional materials could enable the creation of bionic devices possessing unique and compelling geometries, properties, and functionalities. Indeed, interfacing high performance active devices with biology could impact a variety of fields, including regenerative bioelectronic medicines, smart prosthetics, medical robotics, and human-machine interfaces. Biology, from the molecular scale of DNA and proteins, to the macroscopic scale of tissues and organs, is three-dimensional, often soft and stretchable, and temperature sensitive. This renders most biological platforms incompatible with the fabrication and materials processing methods that have been developed and optimized for functional electronics, which are typically planar, rigid and brittle. A number of strategies have been developed to overcome these dichotomies. One particularly novel approach is the use of extrusion-based multi-material 3D printing, which is an additive manufacturing technology that offers a freeform fabrication strategy. This approach addresses the dichotomies presented above by (1) using 3D printing and imaging for customized, hierarchical, and interwoven device architectures; (2) employing nanotechnology as an enabling route for introducing high performance materials, with the potential for exhibiting properties not found in the bulk; and (3) 3D printing a range of soft and nanoscale materials to enable the integration of a diverse palette of high quality functional nanomaterials with biology. Further, 3D printing is a multi-scale platform, allowing for the incorporation of functional nanoscale inks, the printing of microscale features, and ultimately the creation of macroscale devices. This blending of 3D printing, novel nanomaterial properties, and 'living' platforms may enable next-generation bionic systems. In this review, we highlight this synergistic integration of the unique properties of nanomaterials with the

3D printing technologies for electrochemical energy storage

Energy Technology Data Exchange (ETDEWEB)

Zhang, Feng; Wei, Min; Viswanathan, Vilayanur V.; Swart, Benjamin; Shao, Yuyan; Wu, Gang; Zhou, Chi

2017-10-01

Fabrication of electrodes and electrolytes play an important role in promoting the performance of electrochemical energy storage (EES) devices such as batteries and supercapacitors. Traditional fabrication techniques have limited capability in controlling the geometry and architecture of the electrode and solid-state electrolytes, which would otherwise compromise the performance. 3D printing, a disruptive manufacturing technology, has emerged as an innovative approach to fabricating EES devices from nanoscale to macroscale and from nanowatt to megawatt, providing great opportunities to accurately control device geometry (e.g., dimension, porosity, morphology) and structure with enhanced specific energy and power densities. Moreover, the additive manufacturing nature of 3D printing provides excellent controllability of the electrode thickness with much simplified process in a cost effective manner. With the unique spatial and temporal material manipulation capability, 3D printing can integrate multiple nanomaterials in the same print, and multi-functional EES devices (including functional gradient devices) can be fabricated. Herein, we review recent advances in 3D printing of EES devices. We focused on two major 3D printing technologies including direct writing and inkjet printing. The direct material deposition characteristics of these two processes enable them to print on a variety of flat substrates, even a conformal one, well suiting them to applications such as wearable devices and on-chip integrations. Other potential 3D printing techniques such as freeze nano-printing, stereolithography, fused deposition modeling, binder jetting, laminated object manufacturing, and metal 3D printing are also introduced. The advantages and limitations of each 3D printing technology are extensively discussed. More importantly, we provide a perspective on how to integrate the emerging 3D printing with existing technologies to create structures over multiple length scale from

The effects of printing orientation on the electrochemical behaviour of 3D printed acrylonitrile butadiene styrene (ABS)/carbon black electrodes.

Science.gov (United States)

Bin Hamzah, Hairul Hisham; Keattch, Oliver; Covill, Derek; Patel, Bhavik Anil

2018-06-14

Additive manufacturing also known as 3D printing is being utilised in electrochemistry to reproducibly develop complex geometries with conductive properties. In this study, we explored if the electrochemical behavior of 3D printed acrylonitrile butadiene styrene (ABS)/carbon black electrodes was influenced by printing direction. The electrodes were printed in both horizontal and vertical directions. The horizsontal direction resulted in a smooth surface (HPSS electrode) and a comparatively rougher surface (HPRS electrode) surface. Electrodes were characterized using cyclic voltammetry, electrochemical impedance spectroscopy and chronoamperometry. For various redox couples, the vertical printed (VP) electrode showed enhanced current response when compared the two electrode surfaces generated by horizontal print direction. No differences in the capacitive response was observed, indicating that the conductive surface area of all types of electrodes were identical. The VP electrode had reduced charge transfer resistance and uncompensated solution resistance when compared to the HPSS and HPRS electrodes. Overall, electrodes printed in a vertical direction provide enhanced electrochemical performance and our study indicates that print orientation is a key factor that can be used to enhance sensor performance.

Three-Dimensional Printing Surgical Applications.

Science.gov (United States)

AlAli, Ahmad B; Griffin, Michelle F; Butler, Peter E

2015-01-01

Three-dimensional printing, a technology used for decades in the industrial field, gains a lot of attention in the medical field for its potential benefits. With advancement of desktop printers, this technology is accessible and a lot of research is going on in the medical field. To evaluate its application in surgical field, which may include but not limited to surgical planning, surgical education, implants, and prosthesis, which are the focus of this review. Research was conducted by searching PubMed, Web of science, and other reliable sources. We included original articles and excluded articles based on animals, those more than 10 years old, and those not in English. These articles were evaluated, and relevant studies were included in this review. Three-dimensional printing shows a potential benefit in surgical application. Printed implants were used in patient in a few cases and show successful results; however, longer follow-up and more trials are needed. Surgical and medical education is believed to be more efficient with this technology than the current practice. Printed surgical instrument and surgical planning are also believed to improve with three-dimensional printing. Three-dimensional printing can be a very powerful tool in the near future, which can aid the medical field that is facing a lot of challenges and obstacles. However, despite the reported results, further research on larger samples and analytical measurements should be conducted to ensure this technology's impact on the practice.

Four-dimensional Printing of Liquid Crystal Elastomers.

Science.gov (United States)

Ambulo, Cedric P; Burroughs, Julia J; Boothby, Jennifer M; Kim, Hyun; Shankar, M Ravi; Ware, Taylor H

2017-10-25

Three-dimensional structures capable of reversible changes in shape, i.e., four-dimensional-printed structures, may enable new generations of soft robotics, implantable medical devices, and consumer products. Here, thermally responsive liquid crystal elastomers (LCEs) are direct-write printed into 3D structures with a controlled molecular order. Molecular order is locally programmed by controlling the print path used to build the 3D object, and this order controls the stimulus response. Each aligned LCE filament undergoes 40% reversible contraction along the print direction on heating. By printing objects with controlled geometry and stimulus response, magnified shape transformations, for example, volumetric contractions or rapid, repetitive snap-through transitions, are realized.

Strategies in the digital printing value system

OpenAIRE

Mejtoft, Thomas

2006-01-01

The research objective of this thesis is to identify corporate strategies and strategic decisions in the digital printing business and to analyze how these have evolved due to the introduction of digital printing. This thesis comprises three separate studies, all based on qualitative case methodology. The first study is focused on digital printing houses and how their business strategies have changed due to their investment in digital printing production equipment. The second study concentrat...

INIS: Authority list for journal titles

International Nuclear Information System (INIS)

2009-01-01

This is the 35th revision of the INIS: Authority List for Journal Titles (IAEA-INIS-11). This list is published annually and includes the titles of all journals which have contained articles submitted to INIS at the time of publication. The current list contains 13 750 journal titles, 1 965 regularly scanned journals and 593 key journals. It was last updated in March 2009. A journal - or periodical - is a continuing publication issued in a succession of discrete parts, usually bearing numbering and/or chronological designations and intended to be continued indefinitely. It is generally published within a defined, fixed interval between issues and normally appears more than once per year. It includes a mixture of articles, letters, summaries, etc. Within this definition, annuals such as the Annual Review of Nuclear Science are included, but series titles such as the McGraw-Hill Series in Nuclear Engineering are not. The purpose of this document is to provide descriptive cataloguers with standard elements to include in bibliographic level 'S' of the INIS record. These elements include field (tag) 229 (Full Journal Title), 320 (ISSN) and 321 (CODEN). The full journal title is mandatory, and either the ISSN or the CODEN must be included (both may appear). Instructions on how to use this and other elements of the INIS record format are found in INIS: Guide to Bibliographic Description (IAEA-INIS-1). In order to help the user find titles easily, the list is arranged in six parts, followed by summary statistics: - In Part I, all key journals are grouped under the name of the country or international organization responsible for their input in INIS, then sorted alphabetically under their title. - In Part II, all key journals are sorted alphabetically under their title. The name of the country or international organization responsible for their input in INIS is entered in parentheses within the body of the entry. - In Part III, all journals that are regularly scanned by the

Visual Attention to Print-Salient and Picture-Salient Environmental Print in Young Children

Science.gov (United States)

Neumann, Michelle M.; Summerfield, Katelyn; Neumann, David L.

2015-01-01

Environmental print is composed of words and contextual cues such as logos and pictures. The salience of the contextual cues may influence attention to words and thus the potential of environmental print in promoting early reading development. The present study explored this by presenting pre-readers (n = 20) and beginning readers (n = 16) with…

Image once, print thrice? Three-dimensional printing of replacement parts.

Science.gov (United States)

Rankin, Timothy M; Wormer, Blair A; Miller, John D; Giovinco, Nicholas A; Al Kassis, Salam; Armstrong, David G

2018-02-01

The last 20 years has seen an exponential increase in 3D printing as it pertains to the medical industry and more specifically surgery. Previous reviews in this domain have chosen to focus on applications within a specific field. To our knowledge, none have evaluated the broad applications of patient-specific or digital imaging and communications in medicine (DICOM) derived applications of this technology. We searched PUBMED and CINAHL from April 2012 to April 2017. 261 studies fulfilled the inclusion criteria. Proportions of articles reviewed: DICOM (5%), CT (38%), MRI (20%), Ultrasonography (28%), and Bio-printing (9%). There is level IV evidence to support the use of 3D printing for education, pre-operative planning, simulation and implantation. In order to make this technology widely applicable, it will require automation of DICOM to standard tessellation language to implant. Advances in knowledge: Recent lapses in intellectual property and greater familiarity with rapid prototyping in medicine has set the stage for the next generation of custom implants, simulators and autografts. Radiologists may be able to help establish reimbursable procedural terminology.

Designing Biomaterials for 3D Printing.

Science.gov (United States)

Guvendiren, Murat; Molde, Joseph; Soares, Rosane M D; Kohn, Joachim

2016-10-10

Three-dimensional (3D) printing is becoming an increasingly common technique to fabricate scaffolds and devices for tissue engineering applications. This is due to the potential of 3D printing to provide patient-specific designs, high structural complexity, rapid on-demand fabrication at a low-cost. One of the major bottlenecks that limits the widespread acceptance of 3D printing in biomanufacturing is the lack of diversity in "biomaterial inks". Printability of a biomaterial is determined by the printing technique. Although a wide range of biomaterial inks including polymers, ceramics, hydrogels and composites have been developed, the field is still struggling with processing of these materials into self-supporting devices with tunable mechanics, degradation, and bioactivity. This review aims to highlight the past and recent advances in biomaterial ink development and design considerations moving forward. A brief overview of 3D printing technologies focusing on ink design parameters is also included.

Batch fabrication of disposable screen printed SERS arrays.

Science.gov (United States)

Qu, Lu-Lu; Li, Da-Wei; Xue, Jin-Qun; Zhai, Wen-Lei; Fossey, John S; Long, Yi-Tao

2012-03-07

A novel facile method of fabricating disposable and highly reproducible surface-enhanced Raman spectroscopy (SERS) arrays using screen printing was explored. The screen printing ink containing silver nanoparticles was prepared and printed on supporting materials by a screen printing process to fabricate SERS arrays (6 × 10 printed spots) in large batches. The fabrication conditions, SERS performance and application of these arrays were systematically investigated, and a detection limit of 1.6 × 10(-13) M for rhodamine 6G could be achieved. Moreover, the screen printed SERS arrays exhibited high reproducibility and stability, the spot-to-spot SERS signals showed that the intensity variation was less than 10% and SERS performance could be maintained over 12 weeks. Portable high-throughput analysis of biological samples was accomplished using these disposable screen printed SERS arrays.

24 CFR 203.385 - Types of satisfactory title evidence.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Types of satisfactory title... Title Waivers § 203.385 Types of satisfactory title evidence. The following types of title evidence shall be satisfactory to the Commissioner: (a) Fee or owner's title policy. A fee or owner's policy of...

Printed organic thin-film transistor-based integrated circuits

International Nuclear Information System (INIS)

Mandal, Saumen; Noh, Yong-Young

2015-01-01

Organic electronics is moving ahead on its journey towards reality. However, this technology will only be possible when it is able to meet specific criteria including flexibility, transparency, disposability and low cost. Printing is one of the conventional techniques to deposit thin films from solution-based ink. It is used worldwide for visual modes of information, and it is now poised to enter into the manufacturing processes of various consumer electronics. The continuous progress made in the field of functional organic semiconductors has achieved high solubility in common solvents as well as high charge carrier mobility, which offers ample opportunity for organic-based printed integrated circuits. In this paper, we present a comprehensive review of all-printed organic thin-film transistor-based integrated circuits, mainly ring oscillators. First, the necessity of all-printed organic integrated circuits is discussed; we consider how the gap between printed electronics and real applications can be bridged. Next, various materials for printed organic integrated circuits are discussed. The features of these circuits and their suitability for electronics using different printing and coating techniques follow. Interconnection technology is equally important to make this product industrially viable; much attention in this review is placed here. For high-frequency operation, channel length should be sufficiently small; this could be achievable with a combination of surface treatment-assisted printing or laser writing. Registration is also an important issue related to printing; the printed gate should be perfectly aligned with the source and drain to minimize parasitic capacitances. All-printed organic inverters and ring oscillators are discussed here, along with their importance. Finally, future applications of all-printed organic integrated circuits are highlighted. (paper)

Your Next Airplane: Just Hit Print

Science.gov (United States)

2013-04-01

significantly impact the market, but if properly managed, 3-D printing can revolutionize the military through three principal benefits : cost...applications arise, many of which can be tailored to either commercial benefit or military utility. For the military to steer the dialogue over the...from custom chocolate sculptures, to firearms printed in your basement, to light-weight, fuel-efficient printed cars. University research grants

Dramatic Advance in Quality in Flexographic Printing

Directory of Open Access Journals (Sweden)

Jochen Richter

2004-12-01

Full Text Available The enormous changes in flexography printing in recent years concerning the printing quality achievable cannot generally be ascribed to a single revolutionary invention, but are the result of continuous developments to the complete system. Thus the direct drive technology in all machine types and its associated advantages in terms of printing length corrections has become established since drupa 2000. The race for ever finer raster rolls has also been completed to the benefit of improvements in bowl geometry and in ceramic surfaces. Clearly improved colour transfer behaviour has become feasible as a result. In a closely intermeshed system such as flexography printing this naturally has to have an effect on the printing colours used. Further improvements in bonding agents and pigment concentrations now allow users to print ever thinner colour layers while maintaining all of the required authenticities.Furthermore, it has become possible to reduce additional disturbing characteristics in the UV colour area, such as the unpleasant odour. While the digital imaging of printing plates has primarily been improved in terms of economic efficiency by the use of up to eight parallel laser beams, extreme improvements in the system are noticeable especially in the area of directly engraved printing moulds. Whereas many still dismissed directly engraved polymer plates at the last drupa as a laboratory system, the first installation was recently placed on the market a mere three years later. A further noteworthy innovation of recent years that has reached market maturity is thin sleeve technology, which combines the advantages of a photopolymer plate with a round imaged printing mould. There are no high sleeve costs for each printing mould, except for one-off cost for an adapter sleeve. To conclude, it can be said that although flexography printing has experienced many new features in the time between drupa 2000 and today, it still has enormous potential for

3D Printing Electrically Small Spherical Antennas

DEFF Research Database (Denmark)

Kim, Oleksiy S.

2013-01-01

3D printing is applied for rapid prototyping of an electrically small spherical wire antenna. The model is first printed in plastic and subsequently covered with several layers of conductive paint. Measured results are in good agreement with simulations.......3D printing is applied for rapid prototyping of an electrically small spherical wire antenna. The model is first printed in plastic and subsequently covered with several layers of conductive paint. Measured results are in good agreement with simulations....

3D-printing technologies for electrochemical applications.

Science.gov (United States)

Ambrosi, Adriano; Pumera, Martin

2016-05-21

Since its conception during the 80s, 3D-printing, also known as additive manufacturing, has been receiving unprecedented levels of attention and interest from industry and research laboratories. This is in addition to end users, who have benefited from the pervasiveness of desktop-size and relatively cheap printing machines available. 3D-printing enables almost infinite possibilities for rapid prototyping. Therefore, it has been considered for applications in numerous research fields, ranging from mechanical engineering, medicine, and materials science to chemistry. Electrochemistry is another branch of science that can certainly benefit from 3D-printing technologies, paving the way for the design and fabrication of cheaper, higher performing, and ubiquitously available electrochemical devices. Here, we aim to provide a general overview of the most commonly available 3D-printing methods along with a review of recent electrochemistry related studies adopting 3D-printing as a possible rapid prototyping fabrication tool.

High speed printing with polygon scan heads

Science.gov (United States)

Stutz, Glenn

2016-03-01

To reduce and in many cases eliminate the costs associated with high volume printing of consumer and industrial products, this paper investigates and validates the use of the new generation of high speed pulse on demand (POD) lasers in concert with high speed (HS) polygon scan heads (PSH). Associated costs include consumables such as printing ink and nozzles, provisioning labor, maintenance and repair expense as well as reduction of printing lines due to high through put. Targets that are applicable and investigated include direct printing on plastics, printing on paper/cardboard as well as printing on labels. Market segments would include consumer products (CPG), medical and pharmaceutical products, universal ID (UID), and industrial products. In regards to the POD lasers employed, the wavelengths include UV(355nm), Green (532nm) and IR (1064nm) operating within the repetition range of 180 to 250 KHz.

Variable-data Printing Serves - Niches Here, There & Everywhere

Directory of Open Access Journals (Sweden)

Roger Ynostroza

2004-12-01

Full Text Available A milestone focus on high-end digital color presses capable of variable-data imaging - a technology that was introduced ten years ago and is just now at the beginning of wider, more successful implementation in commercial printing-tends to overshadow some real achievements on other variable-data fronts. Those activities involve ink-jet and electrophotographic imaging for high-volume transactional printing, print-on-demand books and catalogs, wide-format proofing and imaging, label production, and printing of text and coding of printed packaging.The capabilities of digital production color presses intrigue commercial printers the most, especially new units referred to by manufacturers as "Series II" or "third-generation" systems. Besides having more press-like characteristics, from offset-caliber quality, image consistency, and high output rates to sturdy construction, reliability, and stock choice, the units seem to represent a way to produce printing that’s beyond the norm.Some users are producing hybrid printed products (offset printing a quantity of "shells" that are later personalized by digital presses, while others are utilizing clients’ "dynamic" databases to personalize marketing materials that drive response rates up to 15%, even 35%. Finally, digital color systems prompt the creation of high-margin Internet-based print providers offering easy-to-design and easy-toorder print materials. Printers may do well to adopt the high-value communications capability that digital imaging offers.

Printing of Wearable Antenna on Textile

Directory of Open Access Journals (Sweden)

Khirotdin Rd. Khairilhijra

2018-01-01

Full Text Available A wearable antenna which is meant to be a part of the clothing used for communication purposes includes tracking, navigation and mobile computing has been seen in demand due to the recent miniaturization of wireless devices. Printing of conductive ink provides flexibility properties on electronics thus allowing it to be used on conformal surfaces. However, the current printing techniques mostly suffer from ink incompatibility and limited of substrates to be printed with. Hence, this paper intend to discloses the printing of wearable antenna using alternative technique via syringe-based deposition system with conductive ink on textile. A validation between simulation and measurement of return loss, (S11 and radiation pattern of the antenna printed is also performed. It was found that a functional antenna is successfully printed on textile since the performances obtained are as expected. The antenna resonated at a minimum resonant frequency of 1.82 GHz which the S11 gathered at-18.90 dB. The radiation pattern for both simulation and measurement is as predicted since both have a larger magnitude of the main lobe than the side lobe. The magnitude of the main lobe from measurement was observed to be 8.83 dB higher than the magnitude of the main lobe of the simulation which is only 3.77 dB. It is proven that the syringe-based deposition system is capable of printing functional antenna on textile.

Inkjet Printed Radio Frequency Passive Components

KAUST Repository

McKerricher, Garret

2015-12-01

Inkjet printing is a mature technique for colourful graphic arts. It excels at customized, large area, high resolution, and small volume production. With the developments in conductive, and dielectric inks, there is potential for large area inkjet electronics fabrication. Passive radio frequency devices can benefit greatly from a printing process, since the size of these devices is defined by the frequency of operation. The large size of radio frequency passives means that they either take up expensive space “on chip” or that they are fabricated on a separate lower cost substrate and somehow bonded to the chips. This has hindered cost-sensitive high volume applications such as radio frequency identification tags. Substantial work has been undertaken on inkjet-printed conductors for passive antennas on microwave substrates and even paper, yet there has been little work on the printing of the dielectric materials aimed at radio frequency passives. Both the conductor and dielectric need to be integrated to create a multilayer inkjet printing process that is capable of making quality passives such as capacitors and inductors. Three inkjet printed dielectrics are investigated in this thesis: a ceramic (alumina), a thermal-cured polymer (poly 4 vinyl phenol), and a UV-cured polymer (acrylic based). For the conductor, both a silver nanoparticle ink as well as a custom in-house formulated particle-free silver ink are explored. The focus is on passives, mainly capacitors and inductors. Compared to low frequency electronics, radio frequency components have additional sensitivity regarding skin depth of the conductor and surface roughness, as well as dielectric constant and loss tangent of the dielectric. These concerns are investigated with the aim of making the highest quality components possible and to understand the current limitations of inkjet-fabricated radio frequency devices. An inkjet-printed alumina dielectric that provides quality factors of 200 and high

Formulating the Right Title for a Research Article.

Science.gov (United States)

Bavdekar, Sandeep B

2016-02-01

Title is an important part of the article. It condenses article content in a few words and captures readers' attention. A good title for a research article is the one which, on its own, is able to introduce the research work to the fullest extent, but in a concise manner. Writing scientific titles that are informative and attractive is a challenging task. This communication describes the importance of titles and the methods of creating appropriate titles for research papers. © Journal of the Association of Physicians of India 2011.

Uniformity of fully gravure printed organic field-effect transistors

International Nuclear Information System (INIS)

Hambsch, M.; Reuter, K.; Stanel, M.; Schmidt, G.; Kempa, H.; Fuegmann, U.; Hahn, U.; Huebler, A.C.

2010-01-01

Fully mass-printed organic field-effect transistors were made completely by means of gravure printing. Therefore a special printing layout was developed in order to avoid register problems in print direction. Upon using this layout, contact pads for source-drain electrodes of the transistors are printed together with the gate electrodes in one and the same printing run. More than 50,000 transistors have been produced and by random tests a yield of approximately 75% has been determined. The principle suitability of the gravure printed transistors for integrated circuits has been shown by the realization of ring oscillators.

3D Printed Robotic Hand

Science.gov (United States)

Pizarro, Yaritzmar Rosario; Schuler, Jason M.; Lippitt, Thomas C.

2013-01-01

Dexterous robotic hands are changing the way robots and humans interact and use common tools. Unfortunately, the complexity of the joints and actuations drive up the manufacturing cost. Some cutting edge and commercially available rapid prototyping machines now have the ability to print multiple materials and even combine these materials in the same job. A 3D model of a robotic hand was designed using Creo Parametric 2.0. Combining "hard" and "soft" materials, the model was printed on the Object Connex350 3D printer with the purpose of resembling as much as possible the human appearance and mobility of a real hand while needing no assembly. After printing the prototype, strings where installed as actuators to test mobility. Based on printing materials, the manufacturing cost of the hand was $167, significantly lower than other robotic hands without the actuators since they have more complex assembly processes.

3D printing in dentistry.

Science.gov (United States)

Dawood, A; Marti Marti, B; Sauret-Jackson, V; Darwood, A

2015-12-01

3D printing has been hailed as a disruptive technology which will change manufacturing. Used in aerospace, defence, art and design, 3D printing is becoming a subject of great interest in surgery. The technology has a particular resonance with dentistry, and with advances in 3D imaging and modelling technologies such as cone beam computed tomography and intraoral scanning, and with the relatively long history of the use of CAD CAM technologies in dentistry, it will become of increasing importance. Uses of 3D printing include the production of drill guides for dental implants, the production of physical models for prosthodontics, orthodontics and surgery, the manufacture of dental, craniomaxillofacial and orthopaedic implants, and the fabrication of copings and frameworks for implant and dental restorations. This paper reviews the types of 3D printing technologies available and their various applications in dentistry and in maxillofacial surgery.

Printed Spacecraft Separation System

Energy Technology Data Exchange (ETDEWEB)

Dehoff, Ryan R [ORNL; Holmans, Walter [Planetary Systems Corporation

2016-10-01

In this project Planetary Systems Corporation proposed utilizing additive manufacturing (3D printing) to manufacture a titanium spacecraft separation system for commercial and US government customers to realize a 90% reduction in the cost and energy. These savings were demonstrated via “printing-in” many of the parts and sub-assemblies into one part, thus greatly reducing the labor associated with design, procurement, assembly and calibration of mechanisms. Planetary Systems Corporation redesigned several of the components of the separation system based on additive manufacturing principles including geometric flexibility and the ability to fabricate complex designs, ability to combine multiple parts of an assembly into a single component, and the ability to optimize design for specific mechanical property targets. Shock absorption was specifically targeted and requirements were established to attenuate damage to the Lightband system from shock of initiation. Planetary Systems Corporation redesigned components based on these requirements and sent the designs to Oak Ridge National Laboratory to be printed. ORNL printed the parts using the Arcam electron beam melting technology based on the desire for the parts to be fabricated from Ti-6Al-4V based on the weight and mechanical performance of the material. A second set of components was fabricated from stainless steel material on the Renishaw laser powder bed technology due to the improved geometric accuracy, surface finish, and wear resistance of the material. Planetary Systems Corporation evaluated these components and determined that 3D printing is potentially a viable method for achieving significant cost and savings metrics.

Effect of hydrophobic microstructured surfaces on conductive ink printing

International Nuclear Information System (INIS)

Kim, Seunghwan; Kang, Hyun Wook; Lee, Kyung Heon; Sung, Hyung Jin

2011-01-01

Conductive ink was printed on various microstructured substrates to measure the printing quality. Poly-dimethylsiloxane (PDMS) substrates were used to test the printability of the hydrophobic surface material. Microstructured arrays of 10 µm regular PDMS cubes were prepared using the MEMS fabrication technique. The gap distance between the cubes was varied from 10 to 40 µm. The printing wettability of the microstructured surfaces was determined by measuring the contact angle of a droplet of silver conductive ink. Screen-printing methods were used in the conductive line printing experiment. Test line patterns with finely varying widths (30–250 µm) were printed repeatedly, and the conductivity of the printed lines was measured. The printability, which was defined as the ratio of the successfully printed patterns to the total number of printed patterns, was analyzed as a function of the linewidth and the gap distance of the microstructured surfaces

A multimaterial electrohydrodynamic jet (E-jet) printing system

International Nuclear Information System (INIS)

Sutanto, E; Shigeta, K; Kim, Y K; Graf, P G; Hoelzle, D J; Barton, K L; Alleyne, A G; Ferreira, P M; Rogers, J A

2012-01-01

Electrohydrodynamic jet (E-jet) printing has emerged as a high-resolution alternative to other forms of direct solution-based fabrication approaches, such as ink-jet printing. This paper discusses the design, integration and operation of a unique E-jet printing platform. The uniqueness lies in the ability to utilize multiple materials in the same overall print-head, thereby enabling increased degrees of heterogeneous integration of different functionalities on a single substrate. By utilizing multiple individual print-heads, with a carrousel indexing among them, increased material flexibility is achieved. The hardware design and system operation for a relatively inexpensive system are developed and presented. Crossover interconnects and multiple fluorescent tagged proteins, demonstrating printed electronics and biological sensing applications, respectively. (paper)

3D inkjet printed radio frequency inductors and capacitors

KAUST Repository

Vaseem, Mohammad

2016-12-08

Inkjet printing has emerged as an ideal method for the fabrication of low cost and efficient electronic systems. However, most of the printed designs at present utilize 2D inkjet printing of metallic inks on conventional substrates. In order to have fully printed RF components, the substrate must also be printed. 3D printing of polymers can be an ideal mechanism for printing substrates, however typically such materials cannot handle high sintering temperatures (>150 0C) required for nanoparticles based metallic inks. In this work, an all-inkjet printed process is demonstrated that utilizes 3D inkjet printing of a UV-cured dielectric material in combination with the printing of a particle free conductive silver organo-complex (SOC) ink for realization of inductors and capacitors. The processing temperature does not exceed 80 0C and still state of the art conductivity of 1×107 S/m is achieved. Both the conductive ink and dielectric have roughness values under 500 nm. The inductor and capacitor exhibit quality factors of 8 and 20 respectively in the high MHz and GHz regime.

Study of lip prints: A forensic study

Directory of Open Access Journals (Sweden)

Vikash Ranjan

2014-01-01

Full Text Available Background: Although several studies have been done on lip prints for human identification in forensic science, there is a doubt about their use in gender determination. Aims: The present study was designed to study the lip groove patterns in all the quadrants of both male and female subjects to identify the sex, based on the patterns of the grooves of the lip prints. Study Design: 300 lip prints were collected from volunteers of D. J. College of Dental Sciences and Research, Modinagar (UP. Materials and Methods: Lip prints were recorded with lip stick and transferred on to a glass slide. Statistical Analysis: Pearson chi-square test was adopted for statistical analysis and probability value (P value was calculated. Conclusion: In our study, none of the lip prints were identical, thus confirming the role of lip prints in individual identification. According to Suzuki′s classification, Type I, II, III and IV patterns were significant in gender determination.

Printing in heterogeneous computer environment at DESY

International Nuclear Information System (INIS)

Jakubowski, Z.

1996-01-01

The number of registered hosts DESY reaches 3500 while the number of print queues approaches 150. The spectrum of used computing environment is very wide: from MAC's and PC's, through SUN, DEC and SGI machines to the IBM mainframe. In 1994 we used 18 tons of paper. We present a solution for providing print services in such an environment for more than 3500 registered users. The availability of the print service is a serious issue. Using centralized printing has a lot of advantages for software administration but creates single point of failure. We solved this problem partially without using expensive software and hardware. The talk provides information about the DESY central central print spooler concept. None of the systems available on the market provides ready to use reliable solution for all platforms used for DESY. We discuss concepts for installation, administration and monitoring large number of printers. We found a solution for printing both on central computing facilities likewise for support of stand-alone workstations. (author)

Network printing in a heterogenous environment

International Nuclear Information System (INIS)

Beyer, C.; Schroth, G.

2001-01-01

Mail and printing are often said to be the most visible services for the user in the network. Though many people talked about the paperless bureau a few years ago it seems that the more digital data is accessible, the more it gets printed. Print management in a heterogenous network environments is typically crossing all operating systems. Each of those brings its own requirements and different printing system implementations with individual user interfaces. The scope is to give the user the advantage and features of the native interface of their operating system while making administration tasks as easy as possible by following the general ideas of a centralised network service on the server side

Exposure assessment of workers in printed electronics workplace.

Science.gov (United States)

Lee, Ji Hyun; Sohn, Eun Kyung; Ahn, Jin Soo; Ahn, Kangho; Kim, Keun Soo; Lee, Jong Hwan; Lee, Taik Min; Yu, Il Je

2013-07-01

Printed electronics uses converging technologies, such as printing, fine mechanics, nanotechnology, electronics and other new technologies. Consequently, printed electronics raises additional health and safety concerns to those experienced in the traditional printing industry. This study investigated two printed electronics workplaces based on a walk-through survey and personal and area sampling. All the printed electronics operations were conducted in a cleanroom. No indication of exposure to excess silver nanoparticles or carbon nanotubes (CNTs) was found. While the organic solvents were lower than current occupational exposure limits, there was a lack of engineering controls, such as local exhaust ventilation, correct enclosure and duct connections. There was also an insufficient quantity of personal protective equipment, and some organic solvents not described in the safety data sheets (SDSs) were detected in the air samples. Plus, the cleaning work, a major emissions operation, was not conducted within a hood, and the cleaning waste was not properly disposed of. Therefore, the present exposure assessment results from two printed electronics workplaces suggest that the printed electronics industry needs to take note of the occupational safety and health risks and hazards already established by the traditional printing industry, along with new risks and hazards originating from converging technologies such as nanotechnology.

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 533 ... Vol 20, No 3 (2002): Focus Issue - Gender and Language ... intertexts: A relevance theoretic approach to intertextuality in print advertising, Abstract ... Vol 32, No 1 (2014), Atomic Homogeneity: A semantic strategy for the ...

µPlasma printing of hydrophobic and hydrophilic patterns to improve wetting behaviour for printed electronics

NARCIS (Netherlands)

Erik Niewenhuis; ir Renee Verkuijlen; Dr Jan Bernards; ir Martijn van Dongen; Lise Verbraeken

2012-01-01

Inkjet printing is a rapidly growing technology for depositing functional materials in the production of organic electronics. Challenges lie among others in the printing of high resolution patterns with high aspect ratio of functional materials to obtain the needed functionality like e.g.

Three-Dimensional Printed Graphene Foams.

Science.gov (United States)

Sha, Junwei; Li, Yilun; Villegas Salvatierra, Rodrigo; Wang, Tuo; Dong, Pei; Ji, Yongsung; Lee, Seoung-Ki; Zhang, Chenhao; Zhang, Jibo; Smith, Robert H; Ajayan, Pulickel M; Lou, Jun; Zhao, Naiqin; Tour, James M

2017-07-25

An automated metal powder three-dimensional (3D) printing method for in situ synthesis of free-standing 3D graphene foams (GFs) was successfully modeled by manually placing a mixture of Ni and sucrose onto a platform and then using a commercial CO 2 laser to convert the Ni/sucrose mixture into 3D GFs. The sucrose acted as the solid carbon source for graphene, and the sintered Ni metal acted as the catalyst and template for graphene growth. This simple and efficient method combines powder metallurgy templating with 3D printing techniques and enables direct in situ 3D printing of GFs with no high-temperature furnace or lengthy growth process required. The 3D printed GFs show high-porosity (∼99.3%), low-density (∼0.015g cm -3 ), high-quality, and multilayered graphene features. The GFs have an electrical conductivity of ∼8.7 S cm -1 , a remarkable storage modulus of ∼11 kPa, and a high damping capacity of ∼0.06. These excellent physical properties of 3D printed GFs indicate potential applications in fields requiring rapid design and manufacturing of 3D carbon materials, for example, energy storage devices, damping materials, and sound absorption.

Indirect X-ray Detectors Based on Inkjet-Printed Photodetectors with a Screen-Printed Scintillator Layer.

Science.gov (United States)

Oliveira, Juliana; Correia, Vitor; Sowade, Enrico; Etxebarria, Ikerne; Rodriguez, Raul D; Mitra, Kalyan Y; Baumann, Reinhard R; Lanceros-Mendez, Senentxu

2018-04-18

Organic photodetectors (PDs) based on printing technologies will allow to expand the current field of PD applications toward large-area and flexible applications in areas such as medical imaging, security, and quality control, among others. Inkjet printing is a powerful digital tool for the deposition of smart and functional materials on various substrates, allowing the development of electronic devices such as PDs on various substrates. In this work, inkjet-printed PD arrays, based on the organic thin-film transistor architecture, have been developed and applied for the indirect detection of X-ray radiation using a scintillator ink as an X-ray absorber. The >90% increase of the photocurrent of the PDs under X-ray radiation, from about 53 nA without the scintillator film to about 102 nA with the scintillator located on top of the PD, proves the suitability of the developed printed device for X-ray detection applications.

Inkjet 3D printing of microfluidic structures—on the selection of the printer towards printing your own microfluidic chips

International Nuclear Information System (INIS)

Walczak, Rafał; Adamski, Krzysztof

2015-01-01

This article reports, for the first time, the results of detailed research on the application of inkjet 3D printing for the fabrication of microfluidic structures. CAD designed test structures were printed with four different printers. Dimensional fidelity, shape conformity, and surface roughness were studied for each printout. It was found that the minimum dimension (width or depth) for a properly printed microfluidic channel was approximately 200 μm. Although the nominal resolution of the printers was one order of magnitude better, smaller structures were significantly deformed or not printed at all. It was also found that a crucial step in one-step fabrication of embedded microchannels is the removal of the support material. We also discuss the source of print error and present a way to evaluate other printers. The printouts obtained from the four different printers were compared, and the optimal printing technique and printer were used to fabricate a microfluidic structure for the spectrophotometric characterisation of beverages. UV/VIS absorbance characteristics were collected using this microfluidic structure, demonstrating that the fabricated spectrophotometric chip operated properly. Thus, a proof-of-concept for using inkjet 3D printing for the fabrication of microfluidic structures was obtained. (paper)

3D Printing of Carbon Nanotubes-Based Microsupercapacitors.

Science.gov (United States)

Yu, Wei; Zhou, Han; Li, Ben Q; Ding, Shujiang

2017-02-08

A novel 3D printing procedure is presented for fabricating carbon-nanotubes (CNTs)-based microsupercapacitors. The 3D printer uses a CNTs ink slurry with a moderate solid content and prints a stream of continuous droplets. Appropriate control of a heated base is applied to facilitate the solvent removal and adhesion between printed layers and to improve the structure integrity without structure delamination or distortion upon drying. The 3D-printed electrodes for microsupercapacitors are characterized by SEM, laser scanning confocal microscope, and step profiler. Effect of process parameters on 3D printing is also studied. The final solid-state microsupercapacitors are assembled with the printed multilayer CNTs structures and poly(vinyl alcohol)-H 3 PO 4 gel as the interdigitated microelectrodes and electrolyte. The electrochemical performance of 3D printed microsupercapacitors is also tested, showing a significant areal capacitance and excellent cycle stability.

Pseudoisochromatic test plate colour representation dependence on printing technology

International Nuclear Information System (INIS)

Luse, K; Ozolinsh, M; Fomins, S

2012-01-01

The aim of the study is to determine best printing technology for creation of colour vision deficiency tests. Valid tests for protanopia and deuteranopia were created from perceived colour matching experiments from printed colour samples by colour deficient individuals. Calibrated EpsonStylus Pro 7800 printer for ink prints and Noritsu HD 3701 digital printer for photographic prints were used. Multispectral imagery (by tunable liquid crystal filters system CRI Nuance Vis 07) data analysis show that in case of ink prints, the measured pixel colour coordinate dispersion (in the CIExy colour diagram) of similar colour arrays is smaller than in case of photographic printing. The print quality in terms of colour coordinate dispersion for printing methods used is much higher than in case of commercially available colour vision deficiency tests.

Paper-based inkjet-printed ultra-wideband fractal antennas

KAUST Repository

Maza, Armando Rodriguez

2012-01-01

For the first time, paper-based inkjet-printed ultra-wideband (UWB) fractal antennas are presented. Two new designs, a miniaturised UWB monopole, which utilises a fractal matching network and is the smallest reported inkjet-printed UWB printed antenna to date, and a fourth-order Koch Snowflake monopole, which utilises a Sierpinski gasket fractal for ink reduction, are demonstrated. It is shown that fractals prove to be a successful method of reducing fabrication costs in inkjet-printed antennas, while retaining or enhancing printed antenna performance. © 2012 The Institution of Engineering and Technology.

Digital Printing Quality Detection and Analysis Technology Based on CCD

Science.gov (United States)

He, Ming; Zheng, Liping

2017-12-01

With the help of CCD digital printing quality detection and analysis technology, it can carry out rapid evaluation and objective detection of printing quality, and can play a certain control effect on printing quality. It can be said CDD digital printing quality testing and analysis of the rational application of technology, its digital printing and printing materials for a variety of printing equipments to improve the quality of a very positive role. In this paper, we do an in-depth study and discussion based on the CCD digital print quality testing and analysis technology.

3D printed soft parallel actuator

Science.gov (United States)

Zolfagharian, Ali; Kouzani, Abbas Z.; Khoo, Sui Yang; Noshadi, Amin; Kaynak, Akif

2018-04-01

This paper presents a 3-dimensional (3D) printed soft parallel contactless actuator for the first time. The actuator involves an electro-responsive parallel mechanism made of two segments namely active chain and passive chain both 3D printed. The active chain is attached to the ground from one end and constitutes two actuator links made of responsive hydrogel. The passive chain, on the other hand, is attached to the active chain from one end and consists of two rigid links made of polymer. The actuator links are printed using an extrusion-based 3D-Bioplotter with polyelectrolyte hydrogel as printer ink. The rigid links are also printed by a 3D fused deposition modelling (FDM) printer with acrylonitrile butadiene styrene (ABS) as print material. The kinematics model of the soft parallel actuator is derived via transformation matrices notations to simulate and determine the workspace of the actuator. The printed soft parallel actuator is then immersed into NaOH solution with specific voltage applied to it via two contactless electrodes. The experimental data is then collected and used to develop a parametric model to estimate the end-effector position and regulate kinematics model in response to specific input voltage over time. It is observed that the electroactive actuator demonstrates expected behaviour according to the simulation of its kinematics model. The use of 3D printing for the fabrication of parallel soft actuators opens a new chapter in manufacturing sophisticated soft actuators with high dexterity and mechanical robustness for biomedical applications such as cell manipulation and drug release.

Quarterly title list for the period ending September 1976

International Nuclear Information System (INIS)

1976-01-01

The title list of the Max-Planck-Institut fuer Plasmaphysik and the Projektgruppe fuer Laserforschung of the MPG is concerned with the period from July until September 1976, and it contains: a) 12 titles and abstracts of laboratory reports, b) 37 titles of publications (30 abstracts), c) 20 titles of articles submitted for publication (16 abstracts), and d) 25 titles of lectures (12 abstracts). (GG) [de

Printing Values In Interactive ROOT

CERN Document Server

Perovic, Boris

2015-01-01

This project report summarizes the work I have been performing during the past twelve weeks as a Summer Student intern working on ROOT project in the SFT group, PH department, under the supervision of Axel Naumann and Danilo Piparo. One of the widely requested features for ROOT was improved interactive shell experience as well as improved printing of object values. Solving this issue was the goal of this project. Primarily, we have enabled printing of the collections. Secondly, we have unified the printing interface, making it much more robust and extendible. Thirdly, we have implemented printing of nested collections in a flexible and user-friendly manner. Finally, we have added an interactive mode, allowing for paginated output. At the beginning of the report, ROOT is presented with examples of where it is used and how important it is. Then, the motivation behind the project is elaborated, by presenting the previous state of the software package and its potential for improvement. Further, the process in wh...

7 CFR 58.340 - Printing and packaging.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Printing and packaging. 58.340 Section 58.340... Procedures § 58.340 Printing and packaging. Printing and packaging of consumer size containers of butter... packaging equipment should be provided. The outside cartons should be removed from bulk butter in a room...

Advances in digital printing and quality considerations of digitally printed images

Science.gov (United States)

Waes, Walter C.

1997-02-01

The traditional 'graphic arts' market has changed very rapidly. It has been only ten years now since Aldus introduced its 'PageMaker' software for text and layout. The platform used was Apple-Mac, which became also the standard for many other graphic applications. The so-called high-end workstations disappeared. This was the start for what later was called: the desk top publishing revolution. At the same time, image scanning became also user-friendly and heavy duty scanners were reduced to desktop-size. Color- reproduction became a commodity product. Since then, the pre-press industry has been going through a technical nightmare, trying to keep up with the digital explosion. One after another, tasks and crafts of pre-press were being transformed by digital technologies. New technologies in this field came almost too fast for many people to adapt. The next digital revolution will be for the commercial printers. All the reasons are explained later in this document. There is now a definite need for a different business-strategy and a new positioning in the electronic media-world. Niches have to be located for new graphic arts- applications. Electronic services to-and-from originators' and executors environments became a requirement. Data can now flow on-line between the printer and the originator of the job. It is no longer the pre-press shop who is controlling this. In many cases, electronic data goes between the print-buyer or agency and the printer. High power communication-systems with accepted standard color- management are transforming the printer, and more particularly, the pre-press shop fatally. The new digital printing market, now in the beginning of its expected full expansion, has to do with growing requests coming from agencies and other print-buyers for: (1) short-run printing; (2) print-on-demand approximately in-time; (3) personalization or other forms of customization; (4) quick turnaround.

3D printing applications for transdermal drug delivery.

Science.gov (United States)

Economidou, Sophia N; Lamprou, Dimitrios A; Douroumis, Dennis

2018-06-15

The role of two and three-dimensional printing as a fabrication technology for sophisticated transdermal drug delivery systems is explored in literature. 3D printing encompasses a family of distinct technologies that employ a virtual model to produce a physical object through numerically controlled apparatuses. The applicability of several printing technologies has been researched for the direct or indirect printing of microneedle arrays or for the modification of their surface through drug-containing coatings. The findings of the respective studies are presented. The range of printable materials that are currently used or potentially can be employed for 3D printing of transdermal drug delivery (TDD) systems is also reviewed. Moreover, the expected impact and challenges of the adoption of 3D printing as a manufacturing technique for transdermal drug delivery systems, are assessed. Finally, this paper outlines the current regulatory framework associated with 3D printed transdermal drug delivery systems. Copyright © 2018 Elsevier B.V. All rights reserved.

Viscoplastic Matrix Materials for Embedded 3D Printing.

Science.gov (United States)

Grosskopf, Abigail K; Truby, Ryan L; Kim, Hyoungsoo; Perazzo, Antonio; Lewis, Jennifer A; Stone, Howard A

2018-03-16

Embedded three-dimensional (EMB3D) printing is an emerging technique that enables free-form fabrication of complex architectures. In this approach, a nozzle is translated omnidirectionally within a soft matrix that surrounds and supports the patterned material. To optimize print fidelity, we have investigated the effects of matrix viscoplasticity on the EMB3D printing process. Specifically, we determine how matrix composition, print path and speed, and nozzle diameter affect the yielded region within the matrix. By characterizing the velocity and strain fields and analyzing the dimensions of the yielded regions, we determine that scaling relationships based on the Oldroyd number, Od, exist between these dimensions and the rheological properties of the matrix materials and printing parameters. Finally, we use EMB3D printing to create complex architectures within an elastomeric silicone matrix. Our methods and findings will both facilitate future characterization of viscoplastic matrices and motivate the development of new materials for EMB3D printing.

Direct Desktop Printed-Circuits-on-Paper Flexible Electronics

Science.gov (United States)

Zheng, Yi; He, Zhizhu; Gao, Yunxia; Liu, Jing

2013-01-01

There currently lacks of a way to directly write out electronics, just like printing pictures on paper by an office printer. Here we show a desktop printing of flexible circuits on paper via developing liquid metal ink and related working mechanisms. Through modifying adhesion of the ink, overcoming its high surface tension by dispensing machine and designing a brush like porous pinhead for printing alloy and identifying matched substrate materials among different papers, the slightly oxidized alloy ink was demonstrated to be flexibly printed on coated paper, which could compose various functional electronics and the concept of Printed-Circuits-on-Paper was thus presented. Further, RTV silicone rubber was adopted as isolating inks and packaging material to guarantee the functional stability of the circuit, which suggests an approach for printing 3D hybrid electro-mechanical device. The present work paved the way for a low cost and easygoing method in directly printing paper electronics.

3D inkjet printed radio frequency inductors and capacitors

KAUST Repository

Vaseem, Mohammad; McKerricher, Garret; Shamim, Atif

2016-01-01

fully printed RF components, the substrate must also be printed. 3D printing of polymers can be an ideal mechanism for printing substrates, however typically such materials cannot handle high sintering temperatures (>150 0C) required for nanoparticles

Quality Inspection of Printed Texts

DEFF Research Database (Denmark)

Pedersen, Jesper Ballisager; Nasrollahi, Kamal; Moeslund, Thomas B.

2016-01-01

-folded: for costumers of the printing and verification system, the overall grade used to verify if the text is of sufficient quality, while for printer's manufacturer, the detailed character/symbols grades and quality measurements are used for the improvement and optimization of the printing task. The proposed system...

Printed organo-functionalized graphene for biosensing applications.

Science.gov (United States)

Wisitsoraat, A; Mensing, J Ph; Karuwan, C; Sriprachuabwong, C; Jaruwongrungsee, K; Phokharatkul, D; Daniels, T M; Liewhiran, C; Tuantranont, A

2017-01-15

Graphene is a highly promising material for biosensors due to its excellent physical and chemical properties which facilitate electron transfer between the active locales of enzymes or other biomaterials and a transducer surface. Printing technology has recently emerged as a low-cost and practical method for fabrication of flexible and disposable electronics devices. The combination of these technologies is promising for the production and commercialization of low cost sensors. In this review, recent developments in organo-functionalized graphene and printed biosensor technologies are comprehensively covered. Firstly, various methods for printing graphene-based fluids on different substrates are discussed. Secondly, different graphene-based ink materials and preparation methods are described. Lastly, biosensing performances of printed or printable graphene-based electrochemical and field effect transistor sensors for some important analytes are elaborated. The reported printed graphene based sensors exhibit promising properties with good reliability suitable for commercial applications. Among most reports, only a few printed graphene-based biosensors including screen-printed oxidase-functionalized graphene biosensor have been demonstrated. The technology is still at early stage but rapidly growing and will earn great attention in the near future due to increasing demand of low-cost and disposable biosensors. Copyright © 2016 Elsevier B.V. All rights reserved.

3D-printed upper limb prostheses: a review.

Science.gov (United States)

Ten Kate, Jelle; Smit, Gerwin; Breedveld, Paul

2017-04-01

This paper aims to provide an overview with quantitative information of existing 3D-printed upper limb prostheses. We will identify the benefits and drawbacks of 3D-printed devices to enable improvement of current devices based on the demands of prostheses users. A review was performed using Scopus, Web of Science and websites related to 3D-printing. Quantitative information on the mechanical and kinematic specifications and 3D-printing technology used was extracted from the papers and websites. The overview (58 devices) provides the general specifications, the mechanical and kinematic specifications of the devices and information regarding the 3D-printing technology used for hands. The overview shows prostheses for all different upper limb amputation levels with different types of control and a maximum material cost of $500. A large range of various prostheses have been 3D-printed, of which the majority are used by children. Evidence with respect to the user acceptance, functionality and durability of the 3D-printed hands is lacking. Contrary to what is often claimed, 3D-printing is not necessarily cheap, e.g., injection moulding can be cheaper. Conversely, 3D-printing provides a promising possibility for individualization, e.g., personalized socket, colour, shape and size, without the need for adjusting the production machine. Implications for rehabilitation Upper limb deficiency is a condition in which a part of the upper limb is missing as a result of a congenital limb deficiency of as a result of an amputation. A prosthetic hand can restore some of the functions of a missing limb and help the user in performing activities of daily living. Using 3D-printing technology is one of the solutions to manufacture hand prostheses. This overview provides information about the general, mechanical and kinematic specifications of all the devices and it provides the information about the 3D-printing technology used to print the hands.

24 CFR 202.11 - Title I.

Science.gov (United States)

2010-04-01

... in 24 CFR 25.5. Civil money penalties may be imposed against Title I lenders and mortgagees pursuant... unacceptable risk to the Department; or (iv) Transfer of a Title I loan to a party that does not have a valid...

Logistics of Three-dimensional Printing: Primer for Radiologists.

Science.gov (United States)

Hodgdon, Taryn; Danrad, Raman; Patel, Midhir J; Smith, Stacy E; Richardson, Michael L; Ballard, David H; Ali, Sayed; Trace, Anthony Paul; DeBenedectis, Carolynn M; Zygmont, Matthew E; Lenchik, Leon; Decker, Summer J

2018-01-01

The Association of University Radiologists Radiology Research Alliance Task Force on three-dimensional (3D) printing presents a review of the logistic considerations for establishing a clinical service using this new technology, specifically focused on implications for radiology. Specific topics include printer selection for 3D printing, software selection, creating a 3D model for printing, providing a 3D printing service, research directions, and opportunities for radiologists to be involved in 3D printing. A thorough understanding of the technology and its capabilities is necessary as the field of 3D printing continues to grow. Radiologists are in the unique position to guide this emerging technology and its use in the clinical arena. Copyright © 2018 The Association of University Radiologists. Published by Elsevier Inc. All rights reserved.

High-Speed Printing Process Characterization using the Lissajous Trajectory Method

Science.gov (United States)

Lee, Sangwon; Kim, Daekeun

2018-04-01

We present a novel stereolithographic three-dimensional (3D) printing process that uses Lissajous trajectories. By using Lissajous trajectories, this 3D printing process allows two laser-scanning mirrors to operate at similar high-speed frequencies simultaneously, and the printing speed can be faster than that of raster scanning used in conventional stereolithography. In this paper, we first propose the basic theoretical background for this printing process based on Lissajous trajectories. We also characterize its printing conditions, such as printing size, laser spot size, and minimum printing resolution, with respect to the operating frequencies of the scanning mirrors and the capability of the laser modulation. Finally, we demonstrate simulation results for printing basic 2D shapes by using a noble printing process algorithm.

A plastic surgery application in evolution: three-dimensional printing.

Science.gov (United States)

Gerstle, Theodore L; Ibrahim, Ahmed M S; Kim, Peter S; Lee, Bernard T; Lin, Samuel J

2014-02-01

Three-dimensional printing represents an evolving technology still in its infancy. Currently, individuals and small business entities have the ability to manufacture physical objects from digital renderings, computer-aided design, and open source files. Design modifications and improvements in extrusion methods have made this technology much more affordable. This article explores the potential uses of three-dimensional printing in plastic surgery. A review was performed detailing the known uses of three-dimensional printing in medicine. The potential applications of three-dimensional printing in plastic surgery are discussed. Various applications for three-dimensional printing technology have emerged in medicine, including printing organs, printing body parts, bio-printing, and computer-aided tissue engineering. In plastic surgery, these tools offer various prospective applications for surgical planning, resident education, and the development of custom prosthetics. Numerous applications exist in medicine, including the printing of devices, implants, tissue replacements, and even whole organs. Plastic surgeons may likely find this technology indispensable in surgical planning, education, and prosthetic device design and development in the near future.

The analysis of ink jet printed eco-font efficiency

Directory of Open Access Journals (Sweden)

Rastko Milošević

2016-07-01

Full Text Available Utilization of eco-font for office printing is one of sustainable, “green” printing concepts, which besides obvious economic benefits, as a result has a certain effect on environmental sustainability as well. The fundamental problem that this practice faces is decreased quality of text printed using eco-fonts comparing to those printed with regular fonts. The aim of this research is eco-font efficiency estimation, i.e. determination of toner usage reduction level of ink jet printed documents typed with this font type, as well as estimation of the extent humans perceive differences between text printed with eco-font and the one printed by its „non-eco“ equivalent. Combining instrumental measuring method and digital image analysis, it was found that this simple principle (eco-font utilization enables substantial toner usage reduction for an ink jet printing system, while visual test showed that visual experience of text printed using eco-font is sufficient. In addition, awareness of benefits that eco-font utilization brings, change users’ attitude towards eco-font quality.

How property title impacts urban consolidation

DEFF Research Database (Denmark)

Easthope, Hazel; Warnken, Jan; Sherry, Cathy

2014-01-01

Continuing urbanisation is triggering an increase in multi-titled housing internationally. This trend has given rise to a substantial research interest in the social consequences of higher density living. Little enquiry, however, has been directed to examining how property title subdivisions gene...

Scalable, full-colour and controllable chromotropic plasmonic printing

OpenAIRE

Xue, Jiancai; Zhou, Zhang-Kai; Wei, Zhiqiang; Su, Rongbin; Lai, Juan; Li, Juntao; Li, Chao; Zhang, Tengwei; Wang, Xue-Hua

2015-01-01

Plasmonic colour printing has drawn wide attention as a promising candidate for the next-generation colour-printing technology. However, an efficient approach to realize full colour and scalable fabrication is still lacking, which prevents plasmonic colour printing from practical applications. Here we present a scalable and full-colour plasmonic printing approach by combining conjugate twin-phase modulation with a plasmonic broadband absorber. More importantly, our approach also demonstrates ...

48 CFR 1631.205-78 - FEHBP printed material costs.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true FEHBP printed material... carrier orders printed material that is available from the Government Printing Office (GPO) under the... COST PRINCIPLES AND PROCEDURES Contracts With Commercial Organizations 1631.205-78 FEHBP printed...

Embedding complex objects with 3d printing

KAUST Repository

Hussain, Muhammad Mustafa

2017-10-12

A CMOS technology-compatible fabrication process for flexible CMOS electronics embedded during additive manufacturing (i.e. 3D printing). A method for such a process may include printing a first portion of a 3D structure; pausing the step of printing the 3D structure to embed the flexible silicon substrate; placing the flexible silicon substrate in a cavity of the first portion of the 3D structure to embed the flexible silicon substrate in the 3D structure; and resuming the step of printing the 3D structure to form the second portion of the 3D structure.

3D Printing the Complete CubeSat

Science.gov (United States)

Kief, Craig

2015-01-01

The 3D Printing the Complete CubeSat project is designed to advance the state-of-the-art in 3D printing for CubeSat applications. Printing in 3D has the potential to increase reliability, reduce design iteration time and provide greater design flexibility in the areas of radiation mitigation, communications, propulsion, and wiring, among others. This project is investigating the possibility of including propulsion systems into the design of printed CubeSat components. One such concept, an embedded micro pulsed plasma thruster (mPPT), could provide auxiliary reaction control propulsion for a spacecraft as a means to desaturate momentum wheels.

Paper-based inkjet-printed ultra-wideband fractal antennas

KAUST Repository

Maza, Armando Rodriguez; Cook, Benjamin Stassen; Jabbour, Ghassan E.; Shamim, Atif

2012-01-01

For the first time, paper-based inkjet-printed ultra-wideband (UWB) fractal antennas are presented. Two new designs, a miniaturised UWB monopole, which utilises a fractal matching network and is the smallest reported inkjet-printed UWB printed

Substitution within the Danish printing industry

DEFF Research Database (Denmark)

Larsen, Henrik Fred; Bøg, Carsten

2009-01-01

are running a substitution project. A major part of the work has been mapping the presence of chemicals which are potential candidates for substitution (e.g. PBT, CMR, vPvB, EDS) within the Danish printing industry and this work was recently finished. The mapping comprises a combination of a literature study......The implementation of the EU REACH regulation will most probably promote substitution within sectors handling a lot of different chemicals like the printing industry. With the aim of being at the cutting edge of this development the Danish EPA together with the Danish printing industry and IPU...... total 15 substances) were found in the Danish printing industry. This paper presents the results of the mapping of chemical candidates and the first results on preparing for actual substitutions....

Comparative Study on Cushion Performance Between 3D Printed Kelvin Structure and 3D Printed Lattice Structure

Science.gov (United States)

Priyadarshini, Lakshmi

Frequently transported packaging goods are more prone to damage due to impact, jolting or vibration in transit. Fragile goods, for example, glass, ceramics, porcelain are susceptible to mechanical stresses. Hence ancillary materials like cushions play an important role when utilized within package. In this work, an analytical model of a 3D cellular structure is established based on Kelvin model and lattice structure. The research will provide a comparative study between the 3D printed Kelvin unit structure and 3D printed lattice structure. The comparative investigation is based on parameters defining cushion performance such as cushion creep, indentation, and cushion curve analysis. The applications of 3D printing is in rapid prototyping where the study will provide information of which model delivers better form of energy absorption. 3D printed foam will be shown as a cost-effective approach as prototype. The research also investigates about the selection of material for 3D printing process. As cushion development demands flexible material, three-dimensional printing with material having elastomeric properties is required. Further, the concept of cushion design is based on Kelvin model structure and lattice structure. The analytical solution provides the cushion curve analysis with respect to the results observed when load is applied over the cushion. The results are reported on basis of attenuation and amplification curves.

Ultrafast Digital Printing toward 4D Shape Changing Materials.

Science.gov (United States)

Huang, Limei; Jiang, Ruiqi; Wu, Jingjun; Song, Jizhou; Bai, Hao; Li, Bogeng; Zhao, Qian; Xie, Tao

2017-02-01

Ultrafast 4D printing (printing converts the structure into 3D. An additional dimension can be incorporated by choosing the printing precursors. The process overcomes the speed limiting steps of typical 3D (4D) printing. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Printing method for organic light emitting device lighting

Science.gov (United States)

Ki, Hyun Chul; Kim, Seon Hoon; Kim, Doo-Gun; Kim, Tae-Un; Kim, Snag-Gi; Hong, Kyung-Jin; So, Soon-Yeol

2013-03-01

Organic Light Emitting Device (OLED) has a characteristic to change the electric energy into the light when the electric field is applied to the organic material. OLED is currently employed as a light source for the lighting tools because research has extensively progressed in the improvement of luminance, efficiency, and life time. OLED is widely used in the plate display device because of a simple manufacture process and high emitting efficiency. But most of OLED lighting projects were used the vacuum evaporator (thermal evaporator) with low molecular. Although printing method has lower efficiency and life time of OLED than vacuum evaporator method, projects of printing OLED actively are progressed because was possible to combine with flexible substrate and printing technology. Printing technology is ink-jet, screen printing and slot coating. This printing method allows for low cost and mass production techniques and large substrates. In this research, we have proposed inkjet printing for organic light-emitting devices has the dominant method of thick film deposition because of its low cost and simple processing. In this research, the fabrication of the passive matrix OLED is achieved by inkjet printing, using a polymer phosphorescent ink. We are measured optical and electrical characteristics of OLED.

High-Performance Screen-Printed Thermoelectric Films on Fabrics.

Science.gov (United States)

Shin, Sunmi; Kumar, Rajan; Roh, Jong Wook; Ko, Dong-Su; Kim, Hyun-Sik; Kim, Sang Il; Yin, Lu; Schlossberg, Sarah M; Cui, Shuang; You, Jung-Min; Kwon, Soonshin; Zheng, Jianlin; Wang, Joseph; Chen, Renkun

2017-08-04

Printing techniques could offer a scalable approach to fabricate thermoelectric (TE) devices on flexible substrates for power generation used in wearable devices and personalized thermo-regulation. However, typical printing processes need a large concentration of binder additives, which often render a detrimental effect on electrical transport of the printed TE layers. Here, we report scalable screen-printing of TE layers on flexible fiber glass fabrics, by rationally optimizing the printing inks consisting of TE particles (p-type Bi 0.5 Sb 1.5 Te 3 or n-type Bi 2 Te 2.7 Se 0.3 ), binders, and organic solvents. We identified a suitable binder additive, methyl cellulose, which offers suitable viscosity for printability at a very small concentration (0.45-0.60 wt.%), thus minimizing its negative impact on electrical transport. Following printing, the binders were subsequently burnt off via sintering and hot pressing. We found that the nanoscale defects left behind after the binder burnt off became effective phonon scattering centers, leading to low lattice thermal conductivity in the printed n-type material. With the high electrical conductivity and low thermal conductivity, the screen-printed TE layers showed high room-temperature ZT values of 0.65 and 0.81 for p-type and n-type, respectively.

The ties that bind: what's in a title?

Science.gov (United States)

Neuhaus, Susan J

2018-03-01

Many Australian and New Zealand surgeons use the title 'Mister' rather than 'Doctor', a practice dating back to traditions established over 600 years ago. The Royal Australasian College of Surgeons is currently undergoing a period of critical self-reflection, embodied by its 'Respect' campaign. Active measures to embrace diversity and encourage women into surgery are underway. This paper reviews the historical basis to the use of gendered titles and their current use amongst fellows. De-identified demographic data from the college register of active fellows was searched by self-identified title, country or state, and gender. Data were further reviewed by surgical sub-specialty and year of fellowship. The college dataset suggests that there is significant variance in the preference for gendered titles, determined predominantly by geography rather than specialty. The highest use of gendered titles (by male and female surgeons) was in Victoria/Tasmania (58% male, 22% female) and New Zealand (81% male, 17% female). By contrast, only 2% of female surgeons in other states elected a gendered title (Miss/Mrs/Ms). Surgery is the only profession that continues to use gendered titles. As the College of Surgeons moves towards greater equity and diversity, consideration should be given to phasing out the use of gendered titles, which serve to divide rather than unite our profession. © 2017 Royal Australasian College of Surgeons.

Pharmaceutical 3D printing: Design and qualification of a single step print and fill capsule.

Science.gov (United States)

Smith, Derrick M; Kapoor, Yash; Klinzing, Gerard R; Procopio, Adam T

2018-06-10

Fused deposition modeling (FDM) 3D printing (3DP) has a potential to change how we envision manufacturing in the pharmaceutical industry. A more common utilization for FDM 3DP is to build upon existing hot melt extrusion (HME) technology where the drug is dispersed in the polymer matrix. However, reliable manufacturing of drug-containing filaments remains a challenge along with the limitation of active ingredients which can sustain the processing risks involved in the HME process. To circumvent this obstacle, a single step FDM 3DP process was developed to manufacture thin-walled drug-free capsules which can be filled with dry or liquid drug product formulations. Drug release from these systems is governed by the combined dissolution of the FDM capsule 'shell' and the dosage form encapsulated in these shells. To prepare the shells, the 3D printer files (extension '.gcode') were modified by creating discrete zones, so-called 'zoning process', with individual print parameters. Capsules printed without the zoning process resulted in macroscopic print defects and holes. X-ray computed tomography, finite element analysis and mechanical testing were used to guide the zoning process and printing parameters in order to manufacture consistent and robust capsule shell geometries. Additionally, dose consistencies of drug containing liquid formulations were investigated in this work. Copyright © 2018 Elsevier B.V. All rights reserved.

No-infill 3D Printing

Science.gov (United States)

Wei, Xiao-Ran; Zhang, Yu-He; Geng, Guo-Hua

2016-09-01

In this paper, we examined how printing the hollow objects without infill via fused deposition modeling, one of the most widely used 3D-printing technologies, by partitioning the objects to shell parts. More specifically, we linked the partition to the exact cover problem. Given an input watertight mesh shape S, we developed region growing schemes to derive a set of surfaces that had inside surfaces that were printable without support on the mesh for the candidate parts. We then employed Monte Carlo tree search over the candidate parts to obtain the optimal set cover. All possible candidate subsets of exact cover from the optimal set cover were then obtained and the bounded tree was used to search the optimal exact cover. We oriented each shell part to the optimal position to guarantee the inside surface was printed without support, while the outside surface was printed with minimum support. Our solution can be applied to a variety of models, closed-hollowed or semi-closed, with or without holes, as evidenced by experiments and performance evaluation on our proposed algorithm.

Print2Screen Mobile App: Embedding Multimedia in Printed ODL Course Materials Using QR Codes

Science.gov (United States)

Abeywardena, Ishan Sudeera

2017-01-01

With the rise of OER and multimedia such as YouTube videos, many academic institutions are becoming mindful of the richness they bring into the teaching and learning process. Given that multimedia resources cannot be directly integrated into printed material, the only available alternative is to print hyperlinks, which teachers and learners can…

40 CFR 300.220 - Related Title III issues.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 27 2010-07-01 2010-07-01 false Related Title III issues. 300.220 Section 300.220 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SUPERFUND, EMERGENCY... PLAN Planning and Preparedness § 300.220 Related Title III issues. Other related Title III requirements...

All-printed paper memory

KAUST Repository

He, Jr-Hau

2016-08-11

All-printed paper-based substrate memory devices are described. In an embodiment, a paper-based memory device is prepared by coating one or more areas of a paper substrate with a conductor material such as a carbon paste, to form a first electrode of a memory, depositing a layer of insulator material, such as titanium dioxide, over one or more areas of the conductor material, and depositing a layer of metal over one or more areas of the insulator material to form a second electrode of the memory. In an embodiment, the device can further include diodes printed between the insulator material and the second electrode, and the first electrode and the second electrodes can be formed as a crossbar structure to provide a WORM memory. The various layers and the diodes can be printed onto the paper substrate by, for example, an ink jet printer.

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 437 ... Journal Home > Advanced Search > Browse Title Index ... prospects and realistic strategies to its implementation in Nigeria\\'s Institute of ... and Communication Technology (ICT) in information dissemination, Abstract.

Browse Title Index

African Journals Online (AJOL)

1986), University Engineering Education and Training in Nigeria: Development, ... Vol 29, No 1 (2010), Use of Energy Method to Simulate the ... of Optimal Rational Composition of Titles Producible from Nigerian Clays ...

Roadmap Through Title XX. Financing Services for Children Through Title XX and Other Programs: Manual 5.

Science.gov (United States)

Copeland, William C.; Iversen, Iver A.

This manual, part of a Hecht Institute four-manual series entitled Financing Children's Services Through Title XX and Related Programs, teaches what Title XX regulations are, what they mean, and what actions and procedures are commanded by them. The first section covers the necessity of rule systems, the characteristics of a good rule system and…

Endodontic applications of 3D printing.

Science.gov (United States)

Anderson, J; Wealleans, J; Ray, J

2018-02-27

Computer-aided design (CAD) and computer-aided manufacturing (CAM) technologies can leverage cone beam computed tomography data for production of objects used in surgical and nonsurgical endodontics and in educational settings. The aim of this article was to review all current applications of 3D printing in endodontics and to speculate upon future directions for research and clinical use within the specialty. A literature search of PubMed, Ovid and Scopus was conducted using the following terms: stereolithography, 3D printing, computer aided rapid prototyping, surgical guide, guided endodontic surgery, guided endodontic access, additive manufacturing, rapid prototyping, autotransplantation rapid prototyping, CAD, CAM. Inclusion criteria were articles in the English language documenting endodontic applications of 3D printing. Fifty-one articles met inclusion criteria and were utilized. The endodontic literature on 3D printing is generally limited to case reports and pre-clinical studies. Documented solutions to endodontic challenges include: guided access with pulp canal obliteration, applications in autotransplantation, pre-surgical planning and educational modelling and accurate location of osteotomy perforation sites. Acquisition of technical expertise and equipment within endodontic practices present formidable obstacles to widespread deployment within the endodontic specialty. As knowledge advances, endodontic postgraduate programmes should consider implementing 3D printing into their curriculums. Future research directions should include clinical outcomes assessments of treatments employing 3D printed objects. Published 2018. This article is a U.S. Government work and is in the public domain in the USA.

Dispenser printed electroluminescent lamps on textiles for smart fabric applications

Science.gov (United States)

de Vos, Marc; Torah, Russel; Tudor, John

2016-04-01

Flexible electroluminescent (EL) lamps are fabricated onto woven textiles using a novel dispenser printing process. Dispenser printing utilizes pressurized air to deposit ink onto a substrate through a syringe and nozzle. This work demonstrates the first use of this technology to fabricate EL lamps. The luminance of the dispenser printed EL lamps is compared to screen-printed EL lamps, both printed on textile, and also commercial EL lamps on polyurethane film. The dispenser printed lamps are shown to have a 1.5 times higher luminance than the best performing commercially available lamp, and have a comparable performance to the screen-printed lamps.

Dispenser printed electroluminescent lamps on textiles for smart fabric applications

International Nuclear Information System (INIS)

De Vos, Marc; Torah, Russel; Tudor, John

2016-01-01

Flexible electroluminescent (EL) lamps are fabricated onto woven textiles using a novel dispenser printing process. Dispenser printing utilizes pressurized air to deposit ink onto a substrate through a syringe and nozzle. This work demonstrates the first use of this technology to fabricate EL lamps. The luminance of the dispenser printed EL lamps is compared to screen-printed EL lamps, both printed on textile, and also commercial EL lamps on polyurethane film. The dispenser printed lamps are shown to have a 1.5 times higher luminance than the best performing commercially available lamp, and have a comparable performance to the screen-printed lamps. (paper)

EU Design Law and 3D Printing

DEFF Research Database (Denmark)

Nordberg, Ana; Schovsbo, Jens Hemmingsen

2017-01-01

The article considers the implications for EU design law of 3D-printing. It first describes the 3D-printing technology and the e-ecosystem which is evolving around the technology and involves a number of new stakeholders who in different ways are engaged in the making and sharing of CAD-files and....../or printing. It is submitted that it is only a matter of time before 3D-printing equipment becomes ubiquitous. It is pointed out how the new technology and e-ecosystem at the same time represent threats and opportunities to design holders and to the societal interests in design and design law. EU design law...

Towards microscale electrohydrodynamic three-dimensional printing

International Nuclear Information System (INIS)

He, Jiankang; Xu, Fangyuan; Cao, Yi; Liu, Yaxiong; Li, Dichen

2016-01-01

It is challenging for the existing three-dimensional (3D) printing techniques to fabricate high-resolution 3D microstructures with low costs and high efficiency. In this work we present a solvent-based electrohydrodynamic 3D printing technique that allows fabrication of microscale structures like single walls, crossed walls, lattice and concentric circles. Process parameters were optimized to deposit tiny 3D patterns with a wall width smaller than 10 μm and a high aspect ratio of about 60. Tight bonding among neighbour layers could be achieved with a smooth lateral surface. In comparison with the existing microscale 3D printing techniques, the presented method is low-cost, highly efficient and applicable to multiple polymers. It is envisioned that this simple microscale 3D printing strategy might provide an alternative and innovative way for application in MEMS, biosensor and flexible electronics. (paper)

3D Printed Multimaterial Microfluidic Valve.

Directory of Open Access Journals (Sweden)

Steven J Keating

Full Text Available We present a novel 3D printed multimaterial microfluidic proportional valve. The microfluidic valve is a fundamental primitive that enables the development of programmable, automated devices for controlling fluids in a precise manner. We discuss valve characterization results, as well as exploratory design variations in channel width, membrane thickness, and membrane stiffness. Compared to previous single material 3D printed valves that are stiff, these printed valves constrain fluidic deformation spatially, through combinations of stiff and flexible materials, to enable intricate geometries in an actuated, functionally graded device. Research presented marks a shift towards 3D printing multi-property programmable fluidic devices in a single step, in which integrated multimaterial valves can be used to control complex fluidic reactions for a variety of applications, including DNA assembly and analysis, continuous sampling and sensing, and soft robotics.

Towards microscale electrohydrodynamic three-dimensional printing

Science.gov (United States)

He, Jiankang; Xu, Fangyuan; Cao, Yi; Liu, Yaxiong; Li, Dichen

2016-02-01

It is challenging for the existing three-dimensional (3D) printing techniques to fabricate high-resolution 3D microstructures with low costs and high efficiency. In this work we present a solvent-based electrohydrodynamic 3D printing technique that allows fabrication of microscale structures like single walls, crossed walls, lattice and concentric circles. Process parameters were optimized to deposit tiny 3D patterns with a wall width smaller than 10 μm and a high aspect ratio of about 60. Tight bonding among neighbour layers could be achieved with a smooth lateral surface. In comparison with the existing microscale 3D printing techniques, the presented method is low-cost, highly efficient and applicable to multiple polymers. It is envisioned that this simple microscale 3D printing strategy might provide an alternative and innovative way for application in MEMS, biosensor and flexible electronics.

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 346 ... Journal Home > Advanced Search > Browse Title Index ... and hygiene promotion services in Rungwe district, Tanzania, Abstract .... as seen in NIgerian teaching hospital: pattern and a simple classification, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 1215 ... Vol 11, No 4 (2017), Retracted: Local Pragmatic Norms in Students' English: An Identity to ... and Communicative Effectiveness of Media Headlines of Print Media ... A Reformist-Feminist Approach to Chimamanda Ngozi Adichie's ... Nigeria‟s Vision 20:2020 Goals: Imperativeness of Arts and Social ...

33 CFR 401.1 - Short title.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Short title. 401.1 Section 401.1 Navigation and Navigable Waters SAINT LAWRENCE SEAWAY DEVELOPMENT CORPORATION, DEPARTMENT OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations § 401.1 Short title. These regulations may be cited as the...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 153 ... Issue, Title. Vol 9, No 2 (2006):, Effects of efficient water utilisation on water resources development in Swaziland under climate change, Abstract .... Ethical, Indigenous and Socio-Economic Perspectives, Abstract.

3D printed replicas for endodontic education.

Science.gov (United States)

Reymus, M; Fotiadou, C; Kessler, A; Heck, K; Hickel, R; Diegritz, C

2018-06-14

To assess the feasibility of producing artificial teeth for endodontic training using 3D printing technology, to analyse the accuracy of the printing process, and to evaluate the teeth by students when used during training. Sound extracted human teeth were selected, digitalized by cone beam computed tomography (CBCT) and appropriate software and finally reproduced by a stereolithographic printer. The printed teeth were scanned and compared with the original ones (trueness) and to one another (precision). Undergraduate dental students in the third and fourth years performed root canal treatment on printed molars and were subsequently asked to evaluate their experience with these compared to real teeth. The workflow was feasible for manufacturing 3D printed tooth replicas. The absolute deviation after printing (trueness) ranged from 50.9μm to 104.3μm. The values for precision ranged from 43.5μm to 68.2μm. Students reported great benefits in the use of the replicated teeth for training purposes. The presented workflow is feasible for any dental educational institution who has access to a CBCT unit and a stereolithographic printer. The accuracy of the printing process is suitable for the production of tooth replicas for endodontic training. Undergraduate students favoured the availability of these replicas and the fairness they ensured in training due to standardization. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Dimensional accuracy of 3D printed vertebra

Science.gov (United States)

Ogden, Kent; Ordway, Nathaniel; Diallo, Dalanda; Tillapaugh-Fay, Gwen; Aslan, Can

2014-03-01

3D printer applications in the biomedical sciences and medical imaging are expanding and will have an increasing impact on the practice of medicine. Orthopedic and reconstructive surgery has been an obvious area for development of 3D printer applications as the segmentation of bony anatomy to generate printable models is relatively straightforward. There are important issues that should be addressed when using 3D printed models for applications that may affect patient care; in particular the dimensional accuracy of the printed parts needs to be high to avoid poor decisions being made prior to surgery or therapeutic procedures. In this work, the dimensional accuracy of 3D printed vertebral bodies derived from CT data for a cadaver spine is compared with direct measurements on the ex-vivo vertebra and with measurements made on the 3D rendered vertebra using commercial 3D image processing software. The vertebra was printed on a consumer grade 3D printer using an additive print process using PLA (polylactic acid) filament. Measurements were made for 15 different anatomic features of the vertebral body, including vertebral body height, endplate width and depth, pedicle height and width, and spinal canal width and depth, among others. It is shown that for the segmentation and printing process used, the results of measurements made on the 3D printed vertebral body are substantially the same as those produced by direct measurement on the vertebra and measurements made on the 3D rendered vertebra.

3D printing for clinical application in otorhinolaryngology.

Science.gov (United States)

Zhong, Nongping; Zhao, Xia

2017-12-01

Three-dimensional (3D) printing is a promising technology that can use a patient's image data to create complex and personalized constructs precisely. It has made great progress over the past few decades and has been widely used in medicine including medical modeling, surgical planning, medical education and training, prosthesis and implants. Three-dimensional (3D) bioprinting is a powerful tool that has the potential to fabricate bioengineered constructs of the desired shape layer-by-layer using computer-aided deposition of living cells and biomaterials. Advances in 3D printed implants and future tissue-engineered constructs will bring great progress to the field of otolaryngology. By integrating 3D printing into tissue engineering and materials, it may be possible for otolaryngologists to implant 3D printed functional grafts into patients for reconstruction of a variety of tissue defects in the foreseeable future. In this review, we will introduce the current state of 3D printing technology and highlight the applications of 3D printed prosthesis and implants, 3D printing technology combined with tissue engineering and future directions of bioprinting in the field of otolaryngology.

EL device pad-printed on a curved surface

International Nuclear Information System (INIS)

Lee, Taik-Min; Hur, Shin; Kim, Jae-Hyun; Choi, Hyun-Cheol

2010-01-01

This paper is unique in that the electroluminescence (EL) display device is fabricated on a curved surface using the pad-printing method. The precision of the pad-printing process is explored to verify whether it can be used for micro patterning. The minimum pattern size and pattern distortion, which is caused by use of the pad, were tested and simulated. The minimal pattern was found to be 35 µm wide and 2.4 µm thick. Pattern distortion when pad-printing on a flat surface, caused by the deformation of the silicon pad, was less than 5 µm. Numerical analysis shows how to estimate pattern distortion when pad-printing on a curved surface. The proposed EL display device consists of five layers, namely a bottom electrode, dielectric layer, phosphor, transparent electrode and a bus electrode. The ink of each layer was reformulated with solvents and the pad-printing conditions were controlled. A PEN film was used first in order to realize the pad-printing process condition of each layer. Finally, the EL display device was printed onto a dish with a radius of curvature of 80 mm. The luminance was 180 cd m −2

Freeform inkjet printing of cellular structures with bifurcations.

Science.gov (United States)

Christensen, Kyle; Xu, Changxue; Chai, Wenxuan; Zhang, Zhengyi; Fu, Jianzhong; Huang, Yong

2015-05-01

Organ printing offers a great potential for the freeform layer-by-layer fabrication of three-dimensional (3D) living organs using cellular spheroids or bioinks as building blocks. Vascularization is often identified as a main technological barrier for building 3D organs. As such, the fabrication of 3D biological vascular trees is of great importance for the overall feasibility of the envisioned organ printing approach. In this study, vascular-like cellular structures are fabricated using a liquid support-based inkjet printing approach, which utilizes a calcium chloride solution as both a cross-linking agent and support material. This solution enables the freeform printing of spanning and overhang features by providing a buoyant force. A heuristic approach is implemented to compensate for the axially-varying deformation of horizontal tubular structures to achieve a uniform diameter along their axial directions. Vascular-like structures with both horizontal and vertical bifurcations have been successfully printed from sodium alginate only as well as mouse fibroblast-based alginate bioinks. The post-printing fibroblast cell viability of printed cellular tubes was found to be above 90% even after a 24 h incubation, considering the control effect. © 2014 Wiley Periodicals, Inc.

Investigation of the adhesion properties of direct 3D printing of polymers and nanocomposites on textiles: Effect of FDM printing process parameters

Science.gov (United States)

Hashemi Sanatgar, Razieh; Campagne, Christine; Nierstrasz, Vincent

2017-05-01

In this paper, 3D printing as a novel printing process was considered for deposition of polymers on synthetic fabrics to introduce more flexible, resource-efficient and cost effective textile functionalization processes than conventional printing process like screen and inkjet printing. The aim is to develop an integrated or tailored production process for smart and functional textiles which avoid unnecessary use of water, energy, chemicals and minimize the waste to improve ecological footprint and productivity. Adhesion of polymer and nanocomposite layers which were 3D printed directly onto the textile fabrics using fused deposition modeling (FDM) technique was investigated. Different variables which may affect the adhesion properties including 3D printing process parameters, fabric type and filler type incorporated in polymer were considered. A rectangular shape according to the peeling standard was designed as 3D computer-aided design (CAD) to find out the effect of the different variables. The polymers were printed in different series of experimental design: nylon on polyamide 66 (PA66) fabrics, polylactic acid (PLA) on PA66 fabric, PLA on PLA fabric, and finally nanosize carbon black/PLA (CB/PLA) and multi-wall carbon nanotubes/PLA (CNT/PLA) nanocomposites on PLA fabrics. The adhesion forces were quantified using the innovative sample preparing method combining with the peeling standard method. Results showed that different variables of 3D printing process like extruder temperature, platform temperature and printing speed can have significant effect on adhesion force of polymers to fabrics while direct 3D printing. A model was proposed specifically for deposition of a commercial 3D printer Nylon filament on PA66 fabrics. In the following, among the printed polymers, PLA and its composites had high adhesion force to PLA fabrics.

Inscribing Authority: Female Title Bearers in Jewish Inscriptions

Directory of Open Access Journals (Sweden)

Carrie Duncan

2012-02-01

Full Text Available This paper investigates representations of gender in the material culture of the ancient synagogue. The pertinent data are numerous dedicatory and funerary inscriptions linking individual Jews, men and women, with titles seemingly associated with leadership in Late Antique synagogues (ca. 200–600 CE. Bernadette Brooten’s influential 1982 monograph argued against the prevailing tendency to characterize these titles as indications of power, authority, and responsibility when associated with men but as meaningless flattery when applied to women. She suggests that synagogue titles denote power, authority and responsibility on all title bearers equally, both men and women. I question the continued utility of proffering female title-holders as enumerable examples of powerful women rescued from their forgotten place in history. Using theoretical insights developed by historians Elizabeth Clark and Gabrielle Spiegel, this paper will engage a comparative analysis with the work of Riet van Bremen and Saba Mahmood to develop new methods of conceptualizing women’s authority in early Jewish communities. I propose that viewing women’s synagogue titles as culturally constructed representations allows for a fruitful inquiry into how women’s titles were used by male-dominated synagogue communities in their self-articulation and public presentation of Judaism.

3D Printing by Multiphase Silicone/Water Capillary Inks.

Science.gov (United States)

Roh, Sangchul; Parekh, Dishit P; Bharti, Bhuvnesh; Stoyanov, Simeon D; Velev, Orlin D

2017-08-01

3D printing of polymers is accomplished easily with thermoplastics as the extruded hot melt solidifies rapidly during the printing process. Printing with liquid polymer precursors is more challenging due to their longer curing times. One curable liquid polymer of specific interest is polydimethylsiloxane (PDMS). This study demonstrates a new efficient technique for 3D printing with PDMS by using a capillary suspension ink containing PDMS in the form of both precured microbeads and uncured liquid precursor, dispersed in water as continuous medium. The PDMS microbeads are held together in thixotropic granular paste by capillary attraction induced by the liquid precursor. These capillary suspensions possess high storage moduli and yield stresses that are needed for direct ink writing. They could be 3D printed and cured both in air and under water. The resulting PDMS structures are remarkably elastic, flexible, and extensible. As the ink is made of porous, biocompatible silicone that can be printed directly inside aqueous medium, it can be used in 3D printed biomedical products, or in applications such as direct printing of bioscaffolds on live tissue. This study demonstrates a number of examples using the high softness, elasticity, and resilience of these 3D printed structures. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

31 CFR 505.01 - Short title.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Short title. 505.01 Section 505.01 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE OF FOREIGN... CERTAIN MERCHANDISE BETWEEN FOREIGN COUNTRIES § 505.01 Short title. The regulations in this part may be...

18 CFR 415.1 - Short title.

Science.gov (United States)

2010-04-01

... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Short title. 415.1 Section 415.1 Conservation of Power and Water Resources DELAWARE RIVER BASIN COMMISSION ADMINISTRATIVE MANUAL BASIN REGULATIONS-FLOOD PLAIN REGULATIONS Generally § 415.1 Short title. This part shall be known...

Student Achievement in Title I Schools

Science.gov (United States)

Diaz, Abby T.

2017-01-01

This researcher seeks to answer the following question: How did two elementary Title I schools, identified as "high performing" on the first Smarter Balanced assessment, address elements of Maslow's hierarchy of needs when developing school-wide initiatives to enhance student achievement? Many students in Title I schools face barriers to…

5 CFR 752.606 - Agency records.

Science.gov (United States)

2010-01-01

... title 38, United States Code; and (6) An employee of the Government Printing Office. (c) Exclusions... title 38, United States Code; and (9) An employee of the Government Printing Office. (d) Employees... employee of the Central Intelligence Agency or the Government Accountability Office; (8) An employee of the...

Printing of polymer microcapsules for enzyme immobilization on paper substrate.

Science.gov (United States)

Savolainen, Anne; Zhang, Yufen; Rochefort, Dominic; Holopainen, Ulla; Erho, Tomi; Virtanen, Jouko; Smolander, Maria

2011-06-13

Poly(ethyleneimine) (PEI) microcapsules containing laccase from Trametes hirsuta (ThL) and Trametes versicolor (TvL) were printed onto paper substrate by three different methods: screen printing, rod coating, and flexo printing. Microcapsules were fabricated via interfacial polycondensation of PEI with the cross-linker sebacoyl chloride, incorporated into an ink, and printed or coated on the paper substrate. The same ink components were used for three printing methods, and it was found that laccase microcapsules were compatible with the ink. Enzymatic activity of microencapsulated TvL was maintained constant in polymer-based ink for at least eight weeks. Thick layers with high enzymatic activity were obtained when laccase-containing microcapsules were screen printed on paper substrate. Flexo printed bioactive paper showed very low activity, since by using this printing method the paper surface was not fully covered by enzyme microcapsules. Finally, screen printing provided a bioactive paper with high water-resistance and the highest enzyme lifetime.

Computer Security: Printing confidentially

CERN Document Server

Stefan Lueders, Computer Security Team

2015-01-01

Have you ever hesitated to print a confidential document using CERN printers? Or perhaps you have rushed quickly to the printer after hitting the “print” button in order to avoid someone else getting hold of and reading your document? These times are over now with the new printing infrastructure!   Indeed, many of us regularly print out confidential documents like our salary slips, MARS forms, tendering documents and drafts of preliminary papers. The upcoming CERN data protection policy will require all of us to respect the confidentiality of such documents and, as the word “confidential” implies, access to “confidential” or sensitive documents will be tightly controlled. What can we do about the public printers located in many buildings, floors and shared spaces - accessible not only to CERN staff and users but also to visitors and guests? Some printers are located in the vicinity of restaurants, cafeterias or close to paths taken b...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 183 ... Journal Home > Advanced Search > Browse Title Index ... Vol 61 (2017), New interventions and sustainable solutions: .... Vol 35 (2011), Resurgence of tribal levies: Double taxation for the rural poor, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 901 - 950 of 1355 ... Journal of Applied Sciences and Environmental Management. ... Journal Home > Advanced Search > Browse Title Index .... Vol 22, No 2 (2018), Performance evaluation of a locally fabricated sawdust fired oven for ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 465 ... Journal Home > Advanced Search > Browse Title Index ... and twinning data of an igbo kindred during the Nigerian Civil War, Abstract ... on laboratory estimations with special reference to clinical chemistry, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 533 ... Southern African Linguistics and Applied Language Studies. ... Issue, Title ... Vol 34, No 1 (2016), Book Review: Qualitative-Quantitative Analyses of .... The complex consonants of simple CV-syllables in Zezuru, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 644 ... Journal Home > Advanced Search > Browse Title Index. Log in or ... Ethics review n international health research: quality assurance or bureaucratic nightmare? Details ... Audit of Management of Open Fractures, Details PDF.

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 165 ... Journal Home > Advanced Search > Browse Title Index ... Vol 43 (2011), Assessment of the Learning Commons takeoff at the University of ... the archive of South Africa's Truth and Reconciliation Commission, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 201 - 241 of 241 ... Vol 8, No 1 (2008), The Nexus between Social Capital and ... Vol 4, No 1 (2004), The print media and conflict resolution in Northern Uganda ... peace, failing women during the peace negotiation process, Abstract PDF ... Competing Concepts on Sudan Identity and National Integration, Abstract PDF.

3D printing for soft robotics - a review.

Science.gov (United States)

Gul, Jahan Zeb; Sajid, Memoon; Rehman, Muhammad Muqeet; Siddiqui, Ghayas Uddin; Shah, Imran; Kim, Kyung-Hwan; Lee, Jae-Wook; Choi, Kyung Hyun

2018-01-01

Soft robots have received an increasing attention due to their advantages of high flexibility and safety for human operators but the fabrication is a challenge. Recently, 3D printing has been used as a key technology to fabricate soft robots because of high quality and printing multiple materials at the same time. Functional soft materials are particularly well suited for soft robotics due to a wide range of stimulants and sensitive demonstration of large deformations, high motion complexities and varied multi-functionalities. This review comprises a detailed survey of 3D printing in soft robotics. The development of key 3D printing technologies and new materials along with composites for soft robotic applications is investigated. A brief summary of 3D-printed soft devices suitable for medical to industrial applications is also included. The growing research on both 3D printing and soft robotics needs a summary of the major reported studies and the authors believe that this review article serves the purpose.

Grey Balance Colorimetry of the Automatically Guided Printing

Directory of Open Access Journals (Sweden)

Igor Zjakic

2005-12-01

Full Text Available Apart from visual control, it is possible to controll the ink on a print by means of auxilliary instruments - densitometer, colorimeter and spectral photometer.One of the problems in offset printing reproduction is the inconstancy of theink flow and ink consumption during the run printing. This problem appears because of the change of ink viscosity, the change of ink temperature, the change of fountain solution quantity in ink, the change of printing speed etc.This article shows the measurements of the chromatic values performed by spectral photometer on the control - signal strip from the very beginning of the run printing till 20000th print. Gray balance (CMY by means of CIE L*a*b* system has been investigated. Densitometric values of the solid area, the growth of the screen values and doubling-shear have been determined. The results of the spectrophotometric measurements of gray balance and the densitometric measurements of the solid tint have been analyzed.

High-Throughput Printing Process for Flexible Electronics

Science.gov (United States)

Hyun, Woo Jin

Printed electronics is an emerging field for manufacturing electronic devices with low cost and minimal material waste for a variety of applications including displays, distributed sensing, smart packaging, and energy management. Moreover, its compatibility with roll-to-roll production formats and flexible substrates is desirable for continuous, high-throughput production of flexible electronics. Despite the promise, however, the roll-to-roll production of printed electronics is quite challenging due to web movement hindering accurate ink registration and high-fidelity printing. In this talk, I will present a promising strategy for roll-to-roll production using a novel printing process that we term SCALE (Self-aligned Capillarity-Assisted Lithography for Electronics). By utilizing capillarity of liquid inks on nano/micro-structured substrates, the SCALE process facilitates high-resolution and self-aligned patterning of electrically functional inks with greatly improved printing tolerance. I will show the fabrication of key building blocks (e.g. transistor, resistor, capacitor) for electronic circuits using the SCALE process on plastics.

Three-dimensional printing and pediatric liver disease.

Science.gov (United States)

Alkhouri, Naim; Zein, Nizar N

2016-10-01

Enthusiastic physicians and medical researchers are investigating the role of three-dimensional printing in medicine. The purpose of the current review is to provide a concise summary of the role of three-dimensional printing technology as it relates to the field of pediatric hepatology and liver transplantation. Our group and others have recently demonstrated the feasibility of printing three-dimensional livers with identical anatomical and geometrical landmarks to the native liver to facilitate presurgical planning of complex liver surgeries. Medical educators are exploring the use of three-dimensional printed organs in anatomy classes and surgical residencies. Moreover, mini-livers are being developed by regenerative medicine scientist as a way to test new drugs and, eventually, whole livers will be grown in the laboratory to replace organs with end-stage disease solving the organ shortage problem. From presurgical planning to medical education to ultimately the bioprinting of whole organs for transplantation, three-dimensional printing will change medicine as we know in the next few years.

The future of 3D printing technology in biomedicine

Directory of Open Access Journals (Sweden)

Iraj Nabipour

2015-07-01

Full Text Available 3D printing, one of the hottest cutting-edge interdisciplinary technologies, is projected to have revenue of $8.4 billion in 2020. #D printing technology will implement the concept of personalized medicine in medical healthcare industry and pharmaceutical fabrication. Organ printing, which it is defined as computer-aided, jet based 3D tissue-engineering of living human organs, is an interesting and challengeable field for 3D printing. Customized implants and prostheses can be produced in any imaginable geometry through the translation of radiological images of patients into digital.stl 3D print files. The creation of anatomical models based on the patient’s pathological conditions using 3D printing technologies would provide good models for training and to design surgical approaches. Hence, 3D printing not only will transform medical healthcare industry but also promises new converging technologies in the field of regenerative medicine.

Forensic print extraction using 3D technology and its processing

Science.gov (United States)

Rajeev, Srijith; Shreyas, Kamath K. M.; Panetta, Karen; Agaian, Sos S.

2017-05-01

Biometric evidence plays a crucial role in criminal scene analysis. Forensic prints can be extracted from any solid surface such as firearms, doorknobs, carpets and mugs. Prints such as fingerprints, palm prints, footprints and lip-prints can be classified into patent, latent, and three-dimensional plastic prints. Traditionally, law enforcement officers capture these forensic traits using an electronic device or extract them manually, and save the data electronically using special scanners. The reliability and accuracy of the method depends on the ability of the officer or the electronic device to extract and analyze the data. Furthermore, the 2-D acquisition and processing system is laborious and cumbersome. This can lead to the increase in false positive and true negative rates in print matching. In this paper, a method and system to extract forensic prints from any surface, irrespective of its shape, is presented. First, a suitable 3-D camera is used to capture images of the forensic print, and then the 3-D image is processed and unwrapped to obtain 2-D equivalent biometric prints. Computer simulations demonstrate the effectiveness of using 3-D technology for biometric matching of fingerprints, palm prints, and lip-prints. This system can be further extended to other biometric and non-biometric modalities.

3D-PRINTING OF BUILD OBJECTS

Directory of Open Access Journals (Sweden)

SAVYTSKYI M. V.

2016-03-01

Full Text Available Raising of problem. Today, in all spheres of our life we can constate the permanent search for new, modern methods and technologies that meet the principles of sustainable development. New approaches need to be, on the one hand more effective in terms of conservation of exhaustible resources of our planet, have minimal impact on the environment and on the other hand to ensure a higher quality of the final product. Construction is not exception. One of the new promising technology is the technology of 3D -printing of individual structures and buildings in general. 3Dprinting - is the process of real object recreating on the model of 3D. Unlike conventional printer which prints information on a sheet of paper, 3D-printer allows you to display three-dimensional information, i.e. creates certain physical objects. Currently, 3D-printer finds its application in many areas of production: machine building elements, a variety of layouts, interior elements, various items. But due to the fact that this technology is fairly new, it requires the creation of detailed and accurate technologies, efficient equipment and materials, and development of common vocabulary and regulatory framework in this field. Research Aim. The analysis of existing methods of creating physical objects using 3D-printing and the improvement of technology and equipment for the printing of buildings and structures. Conclusion. 3D-printers building is a new generation of equipment for the construction of buildings, structures, and structural elements. A variety of building printing technics opens up wide range of opportunities in the construction industry. At this stage, printers design allows to create low-rise buildings of different configurations with different mortars. The scientific novelty of this work is to develop proposals to improve the thermal insulation properties of constructed 3D-printing objects and technological equipment. The list of key terms and notions of construction

ERP system for 3D printing industry

Directory of Open Access Journals (Sweden)

Deaky Bogdan

2017-01-01

Full Text Available GOCREATE is an original cloud-based production management and optimization service which helps 3D printing service providers to use their resources better. The proposed Enterprise Resource Planning system can significantly increase income through improved productivity. With GOCREATE, the 3D printing service providers get a much higher production efficiency at a much lower licensing cost, to increase their competitiveness in the fast growing 3D printing market.

3D freeform printing of silk fibroin.

Science.gov (United States)

Rodriguez, Maria J; Dixon, Thomas A; Cohen, Eliad; Huang, Wenwen; Omenetto, Fiorenzo G; Kaplan, David L

2018-04-15

Freeform fabrication has emerged as a key direction in printing biologically-relevant materials and structures. With this emerging technology, complex structures with microscale resolution can be created in arbitrary geometries and without the limitations found in traditional bottom-up or top-down additive manufacturing methods. Recent advances in freeform printing have used the physical properties of microparticle-based granular gels as a medium for the submerged extrusion of bioinks. However, most of these techniques require post-processing or crosslinking for the removal of the printed structures (Miller et al., 2015; Jin et al., 2016) [1,2]. In this communication, we introduce a novel method for the one-step gelation of silk fibroin within a suspension of synthetic nanoclay (Laponite) and polyethylene glycol (PEG). Silk fibroin has been used as a biopolymer for bioprinting in several contexts, but chemical or enzymatic additives or bulking agents are needed to stabilize 3D structures. Our method requires no post-processing of printed structures and allows for in situ physical crosslinking of pure aqueous silk fibroin into arbitrary geometries produced through freeform 3D printing. 3D bioprinting has emerged as a technology that can produce biologically relevant structures in defined geometries with microscale resolution. Techniques for fabrication of free-standing structures by printing into granular gel media has been demonstrated previously, however, these methods require crosslinking agents and post-processing steps on printed structures. Our method utilizes one-step gelation of silk fibroin within a suspension of synthetic nanoclay (Laponite), with no need for additional crosslinking compounds or post processing of the material. This new method allows for in situ physical crosslinking of pure aqueous silk fibroin into defined geometries produced through freeform 3D printing. Copyright © 2018 Acta Materialia Inc. Published by Elsevier Ltd. All rights

Analysis of the Optical Properties of Screen-Printed and Aerosol-Printed and Plated Fingers of Silicon Solar Cells

Directory of Open Access Journals (Sweden)

R. Woehl

2008-01-01

Full Text Available One main efficiency loss in industrial solar cells is the shading of the cell caused by the metal front side contacts. With the aerosol-printing technique plus an additional light-induced plating (LIP step, not only is the geometrical contact width narrowed compared to screen-printed contacts but also the shape of the finger changes. In this work, the effective shading of different finger types is analysed with two different measurement methods. The essential parameter for characterising the finger is the effective width which can be reduced drastically compared to the geometrical width due to total internal reflection at the glass-air layer and the reflection from the roundish edges of the contact fingers into the cell. This parameter was determined with different methods. It could be shown that for aerosol-printed fingers the effective (optical width is only 38% of its geometrical width, while for standard screen-printed fingers it is 47%. The measured values are compared to a theoretical model for an aerosol-printed and plated finger and are in good agreement.

How useful is 3D printing in maxillofacial surgery?

Science.gov (United States)

Louvrier, A; Marty, P; Barrabé, A; Euvrard, E; Chatelain, B; Weber, E; Meyer, C

2017-09-01

3D printing seems to have more and more applications in maxillofacial surgery (MFS), particularly since the release on the market of general use 3D printers several years ago. The aim of our study was to answer 4 questions: 1. Who uses 3D printing in MFS and is it routine or not? 2. What are the main clinical indications for 3D printing in MFS and what are the kinds of objects that are used? 3. Are these objects printed by an official medical device (MD) manufacturer or made directly within the department or the lab? 4. What are the advantages and drawbacks? Two bibliographic researches were conducted on January the 1st, 2017 in PubMed, without time limitation, using "maxillofacial surgery" AND "3D printing" for the first and for the second "maxillofacial surgery" AND "computer-aided design" AND "computer-aided manufacturing" as keywords. Articles in English or French dealing with human clinical use of 3D printing were selected. Publication date, nationality of the authors, number of patients treated, clinical indication(s), type of printed object(s), type of printing (lab/hospital-made or professional/industry) and advantages/drawbacks were recorded. Two hundred and ninety-seven articles from 35 countries met the criteria. The most represented country was the People's Republic of China (16% of the articles). A total of 2889 patients (10 per article on average) benefited from 3D printed objects. The most frequent clinical indications were dental implant surgery and mandibular reconstruction. The most frequently printed objects were surgical guides and anatomic models. Forty-five percent of the prints were professional. The main advantages were improvement in precision and reduction of surgical time. The main disadvantages were the cost of the objects and the manufacturing period when printed by the industry. The arrival on the market of low-cost printers has increased the use of 3D printing in MFS. Anatomic models are not considered to be MDs and do not have

Improving Heat Transfer Performance of Printed Circuit Boards

Science.gov (United States)

Schatzel, Donald V.

2009-01-01

This paper will explore the ability of printed circuit boards laminated with a Carbon Core Laminate to transfer heat vs. standard printed circuit boards that use only thick layers of copper. The paper will compare the differences in heat transfer performance of printed circuit boards with and without CCL.

3D-printing soft sEMG sensing structures

NARCIS (Netherlands)

Wolterink, Gerjan; Sanders, Remco; Muijzer, Frodo; van Beijnum, Bert-Jan; Krijnen, Gijs

2017-01-01

This paper describes the development and characterization of soft and flexible 3D-printed sEMG electrodes. The electrodes are printed in one go on a low cost consumer multi-material FDM printer. The printed structures do not need any further production steps to give them conductive properties.

Three-Dimensional Printing of Drug-Eluting Implants

DEFF Research Database (Denmark)

Water, Jorrit Jeroen; Bohr, Adam; Bøtker, Johan Peter

2015-01-01

The aim of the present work was to investigate the potential of three-dimensional (3D) printing as a manufacturing method for products intended for personalized treatments by exploring the production of novel polylactide-based feedstock materials for 3D printing purposes. Nitrofurantoin (NF......) and hydroxyapatite (HA) were successfully mixed and extruded with up to 30% drug load with and without addition of 5% HA in polylactide strands, which were subsequently 3D-printed into model disc geometries (10 × 2 mm). X-ray powder diffraction analysis showed that NF maintained its anhydrate solid form during...... of custom-made, drug-loaded feedstock materials for 3D printing of pharmaceutical products for controlled release....

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 414 ... Journal Home > Advanced Search > Browse Title Index. Log in or ... of an algebraic function for the permutation of truth table columns, Abstract ... appraisal and productivity levels in selected Nigerian universities, Abstract.

25 CFR 151.13 - Title examination.

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Title examination. 151.13 Section 151.13 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND AND WATER LAND ACQUISITIONS § 151.13 Title examination. If the Secretary determines that he will approve a request for the acquisition of land from...

3D-Printed Biopolymers for Tissue Engineering Application

Directory of Open Access Journals (Sweden)

Xiaoming Li

2014-01-01

Full Text Available 3D printing technology has recently gained substantial interest for potential applications in tissue engineering due to the ability of making a three-dimensional object of virtually any shape from a digital model. 3D-printed biopolymers, which combine the 3D printing technology and biopolymers, have shown great potential in tissue engineering applications and are receiving significant attention, which has resulted in the development of numerous research programs regarding the material systems which are available for 3D printing. This review focuses on recent advances in the development of biopolymer materials, including natural biopolymer-based materials and synthetic biopolymer-based materials prepared using 3D printing technology, and some future challenges and applications of this technology are discussed.

Cardiothoracic Applications of 3D Printing

Science.gov (United States)

Giannopoulos, Andreas A.; Steigner, Michael L.; George, Elizabeth; Barile, Maria; Hunsaker, Andetta R.; Rybicki, Frank J.; Mitsouras, Dimitris

2016-01-01

Summary Medical 3D printing is emerging as a clinically relevant imaging tool in directing preoperative and intraoperative planning in many surgical specialties and will therefore likely lead to interdisciplinary collaboration between engineers, radiologists, and surgeons. Data from standard imaging modalities such as CT, MRI, echocardiography and rotational angiography can be used to fabricate life-sized models of human anatomy and pathology, as well as patient-specific implants and surgical guides. Cardiovascular 3D printed models can improve diagnosis and allow for advanced pre-operative planning. The majority of applications reported involve congenital heart diseases, valvular and great vessels pathologies. Printed models are suitable for planning both surgical and minimally invasive procedures. Added value has been reported toward improving outcomes, minimizing peri-operative risk, and developing new procedures such as transcatheter mitral valve replacements. Similarly, thoracic surgeons are using 3D printing to assess invasion of vital structures by tumors and to assist in diagnosis and treatment of upper and lower airway diseases. Anatomic models enable surgeons to assimilate information more quickly than image review, choose the optimal surgical approach, and achieve surgery in a shorter time. Patient-specific 3D-printed implants are beginning to appear and may have significant impact on cosmetic and life-saving procedures in the future. In summary, cardiothoracic 3D printing is rapidly evolving and may be a potential game-changer for surgeons. The imager who is equipped with the tools to apply this new imaging science to cardiothoracic care is thus ideally positioned to innovate in this new emerging imaging modality. PMID:27149367

Plasmonic colour laser printing

DEFF Research Database (Denmark)

Zhu, Xiaolong; Vannahme, Christoph; Højlund-Nielsen, Emil

2016-01-01

-beam lithography (EBL) or focused ion beam (FIB), both expensive and not scalable processes that are not suitable for post-processing customization. Here we show a method of colour printing on nanoimprinted plasmonic metasurfaces using laser post-writing. Laser pulses induce transient local heat generation...... that leads to melting and reshaping of the imprinted nanostructures. Depending on the laser pulse energy density, different surface morphologies that support different plasmonic resonances leading to different colour appearances can be created. Using this technique we can print all primary colours...

The Decline of Print: Ten Years of Print Serial Use in a Small Academic Medical Library

Science.gov (United States)

Rosati, Karen Thompson

2006-01-01

Tracking use of print journals over a ten-year period has allowed The University of South Carolina (USC) School of Medicine Library an essential tool for more accurate collection development, for both print and electronic selection. This lengthy study has provided usage statistics for purchasing decisions regarding electronic subscriptions still…

Title IX: With New Opportunities, Girls' Interest Rises

Science.gov (United States)

Toporek, Bryan

2012-01-01

On June 23, 1972, President Richard M. Nixon signed into law Title IX of the Education Amendments of 1972, which prohibits gender discrimination in any federally financed education program or activity. Title IX is far-reaching, but the law is most often associated with school and college athletics. Title IX allows schools to prove their athletic…

3D-printing of undisturbed soil imaged by X-ray

Science.gov (United States)

Bacher, Matthias; Koestel, John; Schwen, Andreas

2014-05-01

The unique pore structures in Soils are altered easily by water flow. Each sample has a different morphology and the results of repetitions vary as well. Soil macropores in 3D-printed durable material avoid erosion and have a known morphology. Therefore potential and limitations of reproducing an undisturbed soil sample by 3D-printing was evaluated. We scanned an undisturbed soil column of Ultuna clay soil with a diameter of 7 cm by micro X-ray computer tomography at a resolution of 51 micron. A subsample cube of 2.03 cm length with connected macropores was cut out from this 3D-image and printed in five different materials by a 3D-printing service provider. The materials were ABS, Alumide, High Detail Resin, Polyamide and Prime Grey. The five print-outs of the subsample were tested on their hydraulic conductivity by using the falling head method. The hydrophobicity was tested by an adapted sessile drop method. To determine the morphology of the print-outs and compare it to the real soil also the print-outs were scanned by X-ray. The images were analysed with the open source program ImageJ. The five 3D-image print-outs copied from the subsample of the soil column were compared by means of their macropore network connectivity, porosity, surface volume, tortuosity and skeleton. The comparison of pore morphology between the real soil and the print-outs showed that Polyamide reproduced the soil macropore structure best while Alumide print-out was the least detailed. Only the largest macropore was represented in all five print-outs. Printing residual material or printing aid material remained in and clogged the pores of all print-out materials apart from Prime Grey. Therefore infiltration was blocked in these print-outs and the materials are not suitable even though the 3D-printed pore shapes were well reproduced. All of the investigated materials were insoluble. The sessile drop method showed angles between 53 and 85 degrees. Prime Grey had the fastest flow rate; the

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 879 ... South African Journal of Higher Education. ... Browse Title Index ... in a USA school setting: Merging transition theory with a narrative approach, Abstract ... Citation analysis of theses and dissertations submitted at the ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 130 ... Journal Home > Advanced Search > Browse Title Index. Log in or ... using the technological pedagogical content knowledge(TPACK) framework, Abstract PDF ... Tamara N. Hrin, Dušica D. Milenković, Mirjana D. Segedinac.

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 278 ... Journal Home > Advanced Search > Browse Title Index ... drie paradigmas beskou: 'n eenheid, of 'n veelheid van perspektiewe? ... Vol 45, No 1 (2011), Genre pedagogy in the mediation of socially-situated literacies ...

Browse Title Index

African Journals Online (AJOL)

Items 251 - 300 of 1260 ... Journal Home > Advanced Search > Browse Title Index ... Consumption of ammonia-nitrogen by aob in immobilized batch culture, Abstract PDF .... Vol 9, No 3S (2017): Special Issue, Design an automatic temperature ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 147 ... Journal Home > Advanced Search > Browse Title Index .... Library (TEEAL) Database among faculty members in Federal University, ... Vol 5, No 2 (2014), Effects of corporate culture on the implementation of automation in ...

Browse Title Index

African Journals Online (AJOL)

Items 201 - 250 of 531 ... Journal Home > Advanced Search > Browse Title Index ... thermal conductivity and viscosity in a flat plate solar collector, Abstract PDF .... similarity method in unsteady two-dimensional MHD boundary layer on the body ...

Inkjet printing and adhesion characterisation of conductive tracks on a commercial printed circuit board material

International Nuclear Information System (INIS)

Sridhar, A.; Dijk, D.J. van; Akkerman, R.

2009-01-01

Silver nanoparticle-based conductive tracks were inkjet printed using a piezoelectric drop-on-demand inkjet printer on a commercially available electronics grade fibre glass (E-glass) reinforced substrate material, and the experimental results have been summarised. Ink jetting was done on two variants of this substrate material, viz. etched and unetched, to determine the influence of substrate surface topography on adhesion and accuracy of the printed tracks. The pull-off adhesion test method was used to quantify adhesive strength. The dependence of the pull-off test results on local geometry of the test area are illustrated with the aid of scanning electron microscope images and interferometer studies. Based on the outcomes of the experiments, conclusions concerning the suitable surface topography for inkjet printing have been arrived at.

Embedding objects during 3D printing to add new functionalities.

Science.gov (United States)

Yuen, Po Ki

2016-07-01

A novel method for integrating and embedding objects to add new functionalities during 3D printing based on fused deposition modeling (FDM) (also known as fused filament fabrication or molten polymer deposition) is presented. Unlike typical 3D printing, FDM-based 3D printing could allow objects to be integrated and embedded during 3D printing and the FDM-based 3D printed devices do not typically require any post-processing and finishing. Thus, various fluidic devices with integrated glass cover slips or polystyrene films with and without an embedded porous membrane, and optical devices with embedded Corning(®) Fibrance™ Light-Diffusing Fiber were 3D printed to demonstrate the versatility of the FDM-based 3D printing and embedding method. Fluid perfusion flow experiments with a blue colored food dye solution were used to visually confirm fluid flow and/or fluid perfusion through the embedded porous membrane in the 3D printed fluidic devices. Similar to typical 3D printed devices, FDM-based 3D printed devices are translucent at best unless post-polishing is performed and optical transparency is highly desirable in any fluidic devices; integrated glass cover slips or polystyrene films would provide a perfect optical transparent window for observation and visualization. In addition, they also provide a compatible flat smooth surface for biological or biomolecular applications. The 3D printed fluidic devices with an embedded porous membrane are applicable to biological or chemical applications such as continuous perfusion cell culture or biocatalytic synthesis but without the need for any post-device assembly and finishing. The 3D printed devices with embedded Corning(®) Fibrance™ Light-Diffusing Fiber would have applications in display, illumination, or optical applications. Furthermore, the FDM-based 3D printing and embedding method could also be utilized to print casting molds with an integrated glass bottom for polydimethylsiloxane (PDMS) device replication

3D Printing of Ball Grid Arrays

Science.gov (United States)

Sinha, Shayandev; Hines, Daniel; Dasgupta, Abhijit; Das, Siddhartha

Ball grid arrays (BGA) are interconnects between an integrated circuit (IC) and a printed circuit board (PCB), that are used for surface mounting electronic components. Typically, lead free alloys are used to make solder balls which, after a reflow process, establish a mechanical and electrical connection between the IC and the PCB. High temperature processing is required for most of these alloys leading to thermal shock causing damage to ICs. For producing flexible circuits on a polymer substrate, there is a requirement for low temperature processing capabilities (around 150 C) and for reducing strain from mechanical stresses. Additive manufacturing techniques can provide an alternative methodology for fabricating BGAs as a direct replacement for standard solder bumped BGAs. We have developed aerosol jet (AJ) printing methods to fabricate a polymer bumped BGA. As a demonstration of the process developed, a daisy chain test chip was polymer bumped using an AJ printed ultra violet (UV) curable polymer ink that was then coated with an AJ printed silver nanoparticle laden ink as a conducting layer printed over the polymer bump. The structure for the balls were achieved by printing the polymer ink using a specific toolpath coupled with in-situ UV curing of the polymer which provided good control over the shape, resulting in well-formed spherical bumps on the order of 200 um wide by 200 um tall for this initial demonstration. A detailed discussion of the AJ printing method and results from accelerated life-time testing will be presented

Printed products for digital cameras and mobile devices

Science.gov (United States)

Fageth, Reiner; Schmidt-Sacht, Wulf

2005-01-01

Digital photography is no longer simply a successor to film. The digital market is now driven by additional devices such as mobile phones with camera and video functions (camphones) as well as innovative products derived from digital files. A large number of consumers do not print their images and non-printing has become the major enemy of wholesale printers, home printing suppliers and retailers. This paper addresses the challenge facing our industry, namely how to encourage the consumer to print images easily and conveniently from all types of digital media.

Browse Title Index

African Journals Online (AJOL)

Items 601 - 650 of 879 ... South African Journal of Higher Education. ... Browse Title Index .... The challenge of thesis supervision in an art university, Abstract ... No 2 (2004), Robert Sternberg's mental self-government theory and its contribution to ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 736 ... Journal Home > Advanced Search > Browse Title Index ... Vol 5 (2008), A Contagious Malady: The Human Quest for Truth through Religion, Abstract ... A Study of Politeness Strategies Used by the National University of ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 879 ... Journal Home > Advanced Search > Browse Title Index ... Vol 20, No 4 (2006), Assessing academic potential for university admission: ... Vol 16, No 2 (2002), Book Review: Rethinking truth by Higgs, P & Smith, J, Details.

Browse Title Index

African Journals Online (AJOL)

Items 651 - 700 of 1199 ... Issue, Title ... Vol 5, No 1 (2011), Motivation, an Essential Ingredient for Optimal Performance in Emerging Markets, Abstract PDF ... Vol 3, No 5 (2009), Multinational transfer pricing and international taxation: what, why, ...

Browse Title Index

African Journals Online (AJOL)

Items 451 - 500 of 533 ... Journal Home > Advanced Search > Browse Title Index .... for past tense forms in Northern Sotho: verb stems with final 'm' and 'n', Abstract ... in an academic writing class: Implications for a dialogic pedagogy, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 701 - 750 of 808 ... Issue, Title ... Vol 58, No 2 (2010), Short Communicaton: The socio-economic impact of helminth infections and the ... Vol 62 (2014): Special Edition, Special edition summarizing the scientific discourse which took place ...

A wearable tracking device inkjet-printed on textile

KAUST Repository

Krykpayev, Bauyrzhan

2017-05-20

Despite the abundance of localization applications, the tracking devices have never been truly realized in E-textiles. Standard printed circuit board (PCB)-based devices are obtrusive and rigid and hence not suitable for textile based implementations. An attractive option would be direct printing of circuit layout on the textile itself, negating the use of rigid PCB materials. However, high surface roughness and porosity of textiles prevents efficient and reliable printing of electronics on textile. In this work, by printing an interface layer on the textile first, a complete localization circuit integrated with an antenna has been inkjet-printed on the textile for the first time. Printed conductive traces were optimized in terms of conductivity and resolution by controlling the number of over-printed layers. The tracking device determines the wearer\\'s position using WiFi and this information can be displayed on any internet-enabled device, such as smart phone. The device is compact (55mm×45mm) and lightweight (22g with 500mAh battery) for people to comfortably wear it and can be easily concealed in case discretion is required. The device operates at 2.4GHz communicated up to a distance of 55m, with localization accuracy of up to 8m.

Digital multicolor printing: state of the art and future challenges

Science.gov (United States)

Kipphan, Helmut

1995-04-01

During the last 5 years, digital techniques have become extremely important in the graphic arts industry. All sections in the production flow for producing multicolor printed products - prepress, printing and postpress - are influenced by digitalization, in an evolutionary and revolutionary way. New equipment and network techniques bring all the sections closer together. The focus is put on high-quality multicolor printing, together with high productivity. Conventional offset printing technology is compared with the leading nonimpact printing technologies. Computer to press is contrasted with computer to print techniques. The newest available digital multicolor presses are described - the direct imaging offset printing press from HEIDELBERG with new laser imaging technique as well as the INDIGO and XEIKON presses based on electrophotography. Regarding technical specifications, economic calculations and print quality, it is worked out that each technique has its own market segments. An outlook is given for future computer to press techniques and the potential of nonimpact printing technologies for advanced high-speed multicolor computer to print equipment. Synergy effects from the NIP-technologies to the conventional printing technologies and vice versa are possible for building up innovative new products, for example hybrid printing systems. It is also shown that there is potential for improving the print quality, based on special screening algorithms, and a higher number of grey levels per pixel by using NIP-technologies. As an intermediate step in digitalization of the production flow, but also as an economical solution computer to plate equipment is described. By producing printed products totally in a digital way, digital color proofing as well as color management systems are needed. The newest high-tech equipment using NIP-technologies for producing proofs is explained. All in all it is shown that the state of the art in digital multicolor printing has reached

Printing Processes Used to Manufacture Photovoltaic Solar Cells

Science.gov (United States)

Rardin, Tina E.; Xu, Renmei

2011-01-01

There is a growing need for renewable energy sources, and solar power is a good option in many instances. Photovoltaic solar panels are now being manufactured via various methods, and different printing processes are being incorporated into the manufacturing process. Screen printing has been used most prevalently in the printing process to make…

3D printing of functional structures

NARCIS (Netherlands)

Krijnen, Gijsbertus J.M.

The technology colloquial known as ‘3D printing’ has developed in such diversity in printing technologies and application fields that meanwhile it seems anything is possible. However, clearly the ideal 3D Printer, with high resolution, multi-material capability, fast printing, etc. is yet to be

Powder-based 3D printing application for geomechanical testing

Science.gov (United States)

Williams, M.; Yoon, H.; Choens, R. C., II; Martinez, M. J.; Dewers, T. A.; Lee, M.

2017-12-01

3D printing of fractured and porous analog geomaterials has the potential to enhance hydrogeological and mechanical interpretations by generating engineered samples in testable configurations with reproducible microstructures and tunable surface and mechanical properties. For geoscience applications, 3D printing technology can be co-opted to print reproducible structures derived from CT-imaging of actual rocks and theoretical algorithms. In particular, the use of 3D printed samples allows us to overcome sample-to-sample heterogeneity that plague rock physics testing and to test material response independent from material variability. In this work, gypsum powder-based 3D printing was used to print cylindrical core samples and block samples with a pre-existing flaw geometry. All samples are printed in three different directions to evaluate the impact of printing direction on mechanical properties. For the cylindrical samples, unconfined compression testing has been performed. For compressive strength, the samples printed perpendicular to the loading direction show stronger than those printed parallel to the loading and at 45 degree. Micro-CT images of the printed samples reveal the uneven spreading of binder, resulting in soft inner core surrounded by stronger outer shell. In particular, the layered feature with binder causes the strong anisotropic properties. This was also confirmed by the wave velocity. For the small block samples ( 6.1cm wide, 10cm high, and 1.25cm thick) with an inclined flaw, uniaxial tests coupled with an array of acoustic emission sensors and digital image correlation revealed that cracks were developed at/near the tip of flaw as expected. Although acoustic events were detected, localization was not detectable mainly due to strong attenuation. Advantage and disadvantage of power-based 3D printing for mechanical testing will be discussed and a few attempts will be presented to improve the applicability of powder-based printing technique. Sandia

ABS 3D printed solutions for cryogenic applications

Science.gov (United States)

Bartolomé, E.; Bozzo, B.; Sevilla, P.; Martínez-Pasarell, O.; Puig, T.; Granados, X.

2017-03-01

3D printing has become a common, inexpensive and rapid prototyping technique, enabling the ad hoc fabrication of complex shapes. In this paper, we demonstrate that 3D printed objects in ABS can be used at cryogenic temperatures, offering flexible solutions in different fields. Firstly, a thermo-mechanical characterization of ABS 3D printed specimens at 77 K is reported, which allowed us to delimit the type of cryogenic uses where 3D printed pieces may be implemented. Secondly, we present three different examples where ABS 3D printed objects working at low temperatures have provided specific solutions: (i) SQUID inserts for angular magnetometry (low temperature material characterization field); (ii) a cage support for a metamaterial ;magnetic concentrator; (superconductivity application), and (iii) dedicated tools for cryopreservation in assisted reproductive techniques (medicine field).

A fully printed ferrite nano-particle ink based tunable antenna

KAUST Repository

Ghaffar, Farhan A.

2016-11-02

Inkjet printing or printing in general has emerged as a very attractive method for the fabrication of low cost and large size electronic systems. However, most of the printed designs rely on nano-particle based metallic inks which are printed on conventional microwave substrates. In order to have a fully printed fabrication process, the substrate also need to be printed. In this paper, a fully printed multi-layer process utilizing custom Fe2O3 based magnetic ink and a silver organic complex (SOC) ink is demonstrated for tunable antennas applications. The ink has been characterized for high frequency and magnetostatic properties. Finally as a proof of concept, a microstrip patch antenna is realized using the proposed fabrication technique which shows a tuning range of 12.5 %.

Nanoparticle composites for printed electronics

International Nuclear Information System (INIS)

Männl, U; Van den Berg, C; Magunje, B; Härting, M; Britton, D T; Jones, S; Van Staden, M J; Scriba, M R

2014-01-01

Printed Electronics is a rapidly developing sector in the electronics industry, in which nanostructured materials are playing an increasingly important role. In particular, inks containing dispersions of semiconducting nanoparticles, can form nanocomposite materials with unique electronic properties when cured. In this study we have extended on our previous studies of functional nanoparticle electronic inks, with the development of a solvent-based silicon ink for printed electronics which is compatible with existing silver inks, and with the investigation of other metal nanoparticle based inks. It is shown that both solvent-based and water-based inks can be used for both silver conductors and semiconducting silicon, and that qualitatively there is no difference in the electronic properties of the materials printed with a soluble polymer binder to when an acrylic binder is used. (paper)

3D-printed patient-specific applications in orthopedics

Directory of Open Access Journals (Sweden)

Wong KC

2016-10-01

Full Text Available Kwok Chuen Wong Department of Orthopedics and Traumatology, Prince of Wales Hospital, The Chinese University of Hong Kong, Shatin, Hong Kong Abstract: With advances in both medical imaging and computer programming, two-dimensional axial images can be processed into other reformatted views (sagittal and coronal and three-dimensional (3D virtual models that represent a patients’ own anatomy. This processed digital information can be analyzed in detail by orthopedic surgeons to perform patient-specific orthopedic procedures. The use of 3D printing is rising and has become more prevalent in medical applications over the last decade as surgeons and researchers are increasingly utilizing the technology’s flexibility in manufacturing objects. 3D printing is a type of manufacturing process in which materials such as plastic or metal are deposited in layers to create a 3D object from a digital model. This additive manufacturing method has the advantage of fabricating objects with complex freeform geometry, which is impossible using traditional subtractive manufacturing methods. Specifically in surgical applications, the 3D printing techniques can not only generate models that give a better understanding of the complex anatomy and pathology of the patients and aid in education and surgical training, but can also produce patient-specific surgical guides or even custom implants that are tailor-made to the surgical requirements. As the clinical workflow of the 3D printing technology continues to evolve, orthopedic surgeons should embrace the latest knowledge of the technology and incorporate it into their clinical practice for patient-specific orthopedic applications. This paper is written to help orthopedic surgeons stay up-to-date on the emerging 3D technology, starting from the acquisition of clinical imaging to 3D printing for patient-specific applications in orthopedics. It 1 presents the necessary steps to prepare the medical images that are

Printed MIMO antenna engineering

CERN Document Server

Sharawi, Mohammad S

2014-01-01

Wireless communications has made a huge leap during the past two decades. The multiple-input-multiple-output (MIMO) technology was proposed in the 1990's as a viable solution that can overcome the data rate limit experienced by single-input-single-output (SISO) systems. This resource is focused on printed MIMO antenna system design. Printed antennas are widely used in mobile and handheld terminals due to their conformity with the device, low cost, good integration within the device elements and mechanical parts, as well as ease of fabrication.A perfect design companion for practicing engineers

Primer printed circuit boards

CERN Document Server

Argyle, Andrew

2009-01-01

Step-by-step instructions for making your own PCBs at home. Making your own printed circuit board (PCB) might seem a daunting task, but once you master the steps, it's easy to attain professional-looking results. Printed circuit boards, which connect chips and other components, are what make almost all modern electronic devices possible. PCBs are made from sheets of fiberglass clad with copper, usually in multiplelayers. Cut a computer motherboard in two, for instance, and you'll often see five or more differently patterned layers. Making boards at home is relatively easy

Browse Title Index

African Journals Online (AJOL)

Items 301 - 350 of 788 ... Journal Home > Advanced Search > Browse Title Index ... Vol 26, No 1 (2018), Gender differentials in the perception of .... Vol 25, No 1 (2017), Impact of total quality management on students' academic performance in ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 194 ... Journal Home > Advanced Search > Browse Title Index ... Vol 14, No 1 (2000), A functional categoriality of adjectives in ... Vol 1, No 1 (1987), Alienation and affirmation: The humanistic vision of Bessie Head, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 1117 ... Journal Home > Advanced Search > Browse Title Index ... Vol 13, No 3 (2007):, an edu-ethical perspecitve on the nature of truth: case studies in elite ... 2009: September: Supplement, An empirical study of university ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 294 ... Journal Home > Advanced Search > Browse Title Index. Log in or .... S Edwards, M Hlongwane, J Thwala, N Robinson ... Vol 16, No 1 (2017), Infancy of internet cafe: The substitute of ubuntu-padare pedagogy, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 98 ... Journal Home > Advanced Search > Browse Title Index ... model for the continued professionalisation of student affairs in Africa, Abstract PDF ... Vol 2, No 2 (2014), Book Review: How College Affects Students, A Third decade ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 76 ... Journal Home > Advanced Search > Browse Title Index ... Vol 4, No 1 (2011), Automation of AutoCAD for Detailing of Reinforced .... Vol 10, No 1 (2017), Housing data base for sustainable housing provision, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 103 ... Issue, Title ... SE Edusah, E Osei-Tutu ... Vol 6, No 2 (2016), Interrelationships among unemployment, inflation and economic growth in Nigeria, Abstract .... Vol 4, No 3 (2014): Special Edition, Socio-cultural Issues for ...

Browse Title Index

African Journals Online (AJOL)

Items 1 - 41 of 41 ... Issue, Title ... Vol 1, No 3 (2004): Special Edition, Assessment of the quality and reserves of Bat ... Vol 1, No 1 (1997), Bovine dermatophilosis in Zambia: epidemiology, socio-economic impacts and future perspectives, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 351 - 391 of 391 ... Issue, Title ... Vol 2, No 3 (1999): Special Edition, The efficacy of low volume application of roundup ... Vol 1, No 1 (1998), The relationships among National Socio-Economic Indicators and Child Health Statistics, Abstract.

Realization of superconductive films by screen printing

International Nuclear Information System (INIS)

Baudry, H.

1988-01-01

Screen printing is a promising method to manufacture superconductive lines making use of superconductive ceramics. An ink has been realized with YBa 2 Cu 3 0 7-x' and the process conditions defined by thermal analysis. A superconductive transition is observed after screen printing on MgO. The firing of the layer is made at 920 0 C followed by a reoxidation step at 420 0 C. The silver electrical contacts are also screen printed [fr

Intrinsic defects in 3D printed materials

OpenAIRE

Bolton, Christopher; Dagastine, Raymond

2015-01-01

We discuss the impact of bulk structural defects on the coherence, phase and polarisation of light passing through transparent 3D printed materials fabricated using a variety of commercial print technologies.

Inkjet Printed Radio Frequency Passive Components

KAUST Repository

McKerricher, Garret

2015-01-01

-resonant frequencies around 1GHz. These fully printed devices have quality factors less than 10. Finally, 3D inkjet-printed UV-cured material is utilized with a novel silver organo-complex ink at 80oC providing conductivity of 1x107 S/m. A lumped element filter

A Framework for 3d Printing

DEFF Research Database (Denmark)

Pilkington, Alan; Frandsen, Thomas; Kapetaniou, Chrystalla

3D printing technologies and processes offer such a radical range of options for firms that we currently lack a structured way of recording possible impact and recommending actions for managers. The changes arising from 3d printing includes more than just new options for product design, but also...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 167 of 167 ... Issue, Title ... Vol 2, No 2 (2013), Women and the Leadership Paradigm: Bridging the Workplace Gender-Gap in Nigeria, Abstract PDF ... Vol 5, No 2 (2016), Women's participation and gender issues in local governance ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 73 of 73 ... Journal Home > Advanced Search > Browse Title Index ... Vol 13 (2006), The ageing eye” functional changes from cradle to gray: A ... Vol 12 (2005), The evaluation of vision in children using monocular vision acuity and ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 391 ... Journal Home > Advanced Search > Browse Title Index ... Efficacy of four Rodenticides on the Ghanaian Market, Abstract ... Vol 2, No 1 (2000):, Determination of some wear elements in used car engine oil and oil filter ...

Browse Title Index

African Journals Online (AJOL)

Items 251 - 300 of 652 ... Journal Home > Advanced Search > Browse Title Index ... Vol 18, No 7 (2015), Introduction to virtual property: Lex virtualis ipsa ... Vol 17, No 1 (2014), Legal challenges relating to the commercial use of outer space, with ...

Browse Title Index

African Journals Online (AJOL)

Items 551 - 600 of 879 ... Journal Home > Advanced Search > Browse Title Index ... A James, E Ralfe, L van Laren, N Ngcobo ... 1 (2011), Recognition of prior learning in promoting lifelong learning: A pedagogy of hope or a shattering of dreams?

Browse Title Index

African Journals Online (AJOL)

Items 1 - 50 of 89 ... Issue, Title ... of two-phased approaches to load balancing in cloud computing, Abstract ... Vol 19, No 1 (2012), Assessing Network Services and Security in ... Vol 23, No 1 (2016), Cloud model construct for transaction-based ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 198 ... Issue, Title ... Vol 13, No 1 (2015), Biometric Enhancement of Home and Office Security to Reduce Assassinations in Nigeria, Abstract PDF ... Vol 9, No 1 (2013), Cloud Computing: Key to IT Development in West Africa ...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 198 of 198 ... Issue, Title ... scheme for QoS and energy conservation in cloud computing, Abstract PDF ... Vol 9, No 1 (2013), Performance and Security Evaluation of ... Vol 18, No 1 (2017), Reducing capital flight through local cloud ...

Browse Title Index

African Journals Online (AJOL)

Items 51 - 97 of 97 ... Journal Home > Advanced Search > Browse Title Index ... Vol 20, No 2 (2008), Research Note: Anthropometric data of the foot of ... Vol 26, No 1 (2014), Validation of the Automation Attitude Questionnaire for Airline Pilots ...

Titles of Midas

Directory of Open Access Journals (Sweden)

G. L. Huxley

2001-09-01

Full Text Available The Phrygian inscription on the tomb at Yazılıkaya (8th century gives Midas the titles wanax and lawagtas, paralled in Mycenaean, and there were strong connections between his dynasty and Greek Aeolis.

Browse Title Index

African Journals Online (AJOL)

Items 51 - 100 of 412 ... Issue, Title. Vol 30, No 3 (2011) ... Transferring the principle of double effect from war to business, Abstract. G. J. Rossouw ... Vol 22, No 2 (2003), Can more business ethics teaching halt corruption in companies? Abstract.

Inkjet printing of single-crystal films.

Science.gov (United States)

Minemawari, Hiromi; Yamada, Toshikazu; Matsui, Hiroyuki; Tsutsumi, Jun'ya; Haas, Simon; Chiba, Ryosuke; Kumai, Reiji; Hasegawa, Tatsuo

2011-07-13

The use of single crystals has been fundamental to the development of semiconductor microelectronics and solid-state science. Whether based on inorganic or organic materials, the devices that show the highest performance rely on single-crystal interfaces, with their nearly perfect translational symmetry and exceptionally high chemical purity. Attention has recently been focused on developing simple ways of producing electronic devices by means of printing technologies. 'Printed electronics' is being explored for the manufacture of large-area and flexible electronic devices by the patterned application of functional inks containing soluble or dispersed semiconducting materials. However, because of the strong self-organizing tendency of the deposited materials, the production of semiconducting thin films of high crystallinity (indispensable for realizing high carrier mobility) may be incompatible with conventional printing processes. Here we develop a method that combines the technique of antisolvent crystallization with inkjet printing to produce organic semiconducting thin films of high crystallinity. Specifically, we show that mixing fine droplets of an antisolvent and a solution of an active semiconducting component within a confined area on an amorphous substrate can trigger the controlled formation of exceptionally uniform single-crystal or polycrystalline thin films that grow at the liquid-air interfaces. Using this approach, we have printed single crystals of the organic semiconductor 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C(8)-BTBT) (ref. 15), yielding thin-film transistors with average carrier mobilities as high as 16.4 cm(2) V(-1) s(-1). This printing technique constitutes a major step towards the use of high-performance single-crystal semiconductor devices for large-area and flexible electronics applications.

Printing microstructures in a polymer matrix using a ferrofluid droplet

International Nuclear Information System (INIS)

Abdel Fattah, Abdel Rahman; Ghosh, Suvojit; Puri, Ishwar K.

2016-01-01

We print complex curvilinear microstructures in an elastomer matrix using a ferrofluid droplet as the print head. A magnetic field moves the droplet along a prescribed path in liquid polydimethylsiloxane (PDMS). The droplet sheds magnetic nanoparticle (MNP) clusters in its wake, forming printed features. The PDMS is subsequently heated so that it crosslinks, which preserves the printed features in the elastomer matrix. The competition between magnetic and drag forces experienced by the ferrofluid droplet and its trailing MNPs highlight design criteria for successful printing, which are experimentally confirmed. The method promises new applications, such as flexible 3D circuitry. - Highlights: • Magnetically guided miscible ferrofluid droplets print 3D patterns in a polymer. • Printing mechanism depends on the dynamics between the fluid and magnetic forces. • Droplet size influences the width of the printed trail. • The Colloidal distribution of the ferrofluid is important for pattern integrity. • Particle trajectories and trails are simulated and validated through experiments.

3D printed plastics for beam modulation in proton therapy

International Nuclear Information System (INIS)

Lindsay, C; Hoehr, C; Kumlin, J; Schaffer, P; Jirasek, A; Lee, R; Martinez, D M

2015-01-01

Two 3D printing methods, fused filament fabrication (FFF) and PolyJet™ (PJ) were investigated for suitability in clinical proton therapy (PT) energy modulation. Measurements of printing precision, printed density and mean stopping power are presented. FFF is found to be accurate to 0.1 mm, to contain a void fraction of 13% due to air pockets and to have a mean stopping power dependent on geometry. PJ was found to print accurate to 0.05 mm, with a material density and mean stopping power consistent with solid poly(methyl methacrylate) (PMMA). Both FFF and PJ were found to print significant, sporadic defects associated with sharp edges on the order of 0.2 mm. Site standard PT modulator wheels were printed using both methods. Measured depth-dose profiles with a 74 MeV beam show poor agreement between PMMA and printed FFF wheels. PJ printed wheel depth-dose agreed with PMMA within 1% of treatment dose except for a distal falloff discrepancy of 0.5 mm. (note)

Electrohydrodynamic printing of silver nanowires for flexible and stretchable electronics.

Science.gov (United States)

Cui, Zheng; Han, Yiwei; Huang, Qijin; Dong, Jingyan; Zhu, Yong

2018-04-19

A silver nanowire (AgNW) based conductor is a promising component for flexible and stretchable electronics. A wide range of flexible/stretchable devices using AgNW conductors has been demonstrated recently. High-resolution, high-throughput printing of AgNWs remains a critical challenge. Electrohydrodynamic (EHD) printing has been developed as a promising technique to print different materials on a variety of substrates with high resolution. Here, AgNW ink was developed for EHD printing. The printed features can be controlled by several parameters including AgNW concentration, ink viscosity, printing speed, stand-off distance, etc. With this method, AgNW patterns can be printed on a range of substrates, e.g. paper, polyethylene terephthalate (PET), glass, polydimethylsiloxane (PDMS), etc. First, AgNW samples on PDMS were characterized under bending and stretching. Then AgNW heaters and electrocardiogram (ECG) electrodes were fabricated to demonstrate the potential of this printing technique for AgNW-based flexible and stretchable devices.

Printing microstructures in a polymer matrix using a ferrofluid droplet

Energy Technology Data Exchange (ETDEWEB)

Abdel Fattah, Abdel Rahman [Department of Mechanical Engineering, Hamilton, Ontario (Canada); Ghosh, Suvojit [Department of Engineering Physics, McMaster University, Hamilton, Ontario (Canada); Puri, Ishwar K. [Department of Mechanical Engineering, Hamilton, Ontario (Canada); Department of Engineering Physics, McMaster University, Hamilton, Ontario (Canada)

2016-03-01

We print complex curvilinear microstructures in an elastomer matrix using a ferrofluid droplet as the print head. A magnetic field moves the droplet along a prescribed path in liquid polydimethylsiloxane (PDMS). The droplet sheds magnetic nanoparticle (MNP) clusters in its wake, forming printed features. The PDMS is subsequently heated so that it crosslinks, which preserves the printed features in the elastomer matrix. The competition between magnetic and drag forces experienced by the ferrofluid droplet and its trailing MNPs highlight design criteria for successful printing, which are experimentally confirmed. The method promises new applications, such as flexible 3D circuitry. - Highlights: • Magnetically guided miscible ferrofluid droplets print 3D patterns in a polymer. • Printing mechanism depends on the dynamics between the fluid and magnetic forces. • Droplet size influences the width of the printed trail. • The Colloidal distribution of the ferrofluid is important for pattern integrity. • Particle trajectories and trails are simulated and validated through experiments.

A brief review of extrusion-based tissue scaffold bio-printing.

Science.gov (United States)

Ning, Liqun; Chen, Xiongbiao

2017-08-01

Extrusion-based bio-printing has great potential as a technique for manipulating biomaterials and living cells to create three-dimensional (3D) scaffolds for damaged tissue repair and function restoration. Over the last two decades, advances in both engineering techniques and life sciences have evolved extrusion-based bio-printing from a simple technique to one able to create diverse tissue scaffolds from a wide range of biomaterials and cell types. However, the complexities associated with synthesis of materials for bio-printing and manipulation of multiple materials and cells in bio-printing pose many challenges for scaffold fabrication. This paper presents an overview of extrusion-based bio-printing for scaffold fabrication, focusing on the prior-printing considerations (such as scaffold design and materials/cell synthesis), working principles, comparison to other techniques, and to-date achievements. This paper also briefly reviews the recent development of strategies with regard to hydrogel synthesis, multi-materials/cells manipulation, and process-induced cell damage in extrusion-based bio-printing. The key issue and challenges for extrusion-based bio-printing are also identified and discussed along with recommendations for future, aimed at developing novel biomaterials and bio-printing systems, creating patterned vascular networks within scaffolds, and preserving the cell viability and functions in scaffold bio-printing. The address of these challenges will significantly enhance the capability of extrusion-based bio-printing. Copyright © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

75 FR 6024 - Agency Information Collection Activities; Submission to OMB for Review and Approval; Comment...

Science.gov (United States)

2010-02-05

....regulations.gov . Title: NESHAP for Printing and Publishing Industry (Renewal). ICR Numbers: EPA ICR Number... disclose the information. Respondents/Affected Entities: Printing and publishing industry. Estimated Number... with the printing and publishing industry representatives, the printing industry in particular, will be...

Ultrasonic properties of all-printed piezoelectric polymer transducers

Science.gov (United States)

Wagle, Sanat; Decharat, Adit; Bodö, Peter; Melandsø, Frank

2013-12-01

The ability of producing ultrasonic transducers from screen-printing has been explored experimentally, through printing and characterization of a large number of transducers. In an all-printed test design, 124 transducers with four different electrode sizes ranging from 1 to 4.9 mm2, were printed layer-by-layer on a high performance polyethyleneimine polymer. Inks from ferroelectric and conductive polymers were applied to the active part of a transducer, to provide a good acoustical match between the individual layers. Ultrasonic characterizations of the transducers done by two independent methods provided a broad-banded frequency response with a maximum response around 100 MHz.

Printed circuits and their applications: Which way forward?

Science.gov (United States)

Cantatore, E.

2015-09-01

The continuous advancements in printed electronics make nowadays feasible the design of printed circuits which enable meaningful applications. Examples include ultra-low cost sensors embedded in food packaging, large-area sensing surfaces and biomedical assays. This paper offers an overview of state-of-the-art digital and analog circuit blocks, manufactured with a printed complementary organic TFT technology. An analog to digital converter and an RFID tag implemented exploiting these building blocks are also described. The main remaining drawbacks of the printed technology described are identified, and new approaches to further improve the state of the art, enabling more innovative applications are discussed.

Standard practice for preparing sulfur prints for macrostructural evaluation

CERN Document Server

American Society for Testing and Materials. Philadelphia

2008-01-01

1.1 This practice provides information required to prepare sulfur prints (also referred to as Baumann Prints) of most ferrous alloys to reveal the distribution of sulfide inclusions. 1.2 The sulfur print reveals the distribution of sulfides in steels with bulk sulfur contents between about 0.010 and 0.40 weight percent. 1.3 Certain steels contain complex sulfides that do not respond to the test solutions, for example, steels containing titanium sulfides or chromium sulfides. 1.4 The sulfur print test is a qualitative test. The density of the print image should not be used to assess the sulfur content of a steel. Under carefully controlled conditions, it is possible to compare print image intensities if the images are formed only by manganese sulfides. 1.5 The sulfur print image will reveal details of the solidification pattern or metal flow from hot or cold working on appropriately chosen and prepared test specimens. 1.6 This practice does not address acceptance criteria based on the use of the method. ...

Novel Biomaterials Used in Medical 3D Printing Techniques

Directory of Open Access Journals (Sweden)

Karthik Tappa

2018-02-01

Full Text Available The success of an implant depends on the type of biomaterial used for its fabrication. An ideal implant material should be biocompatible, inert, mechanically durable, and easily moldable. The ability to build patient specific implants incorporated with bioactive drugs, cells, and proteins has made 3D printing technology revolutionary in medical and pharmaceutical fields. A vast variety of biomaterials are currently being used in medical 3D printing, including metals, ceramics, polymers, and composites. With continuous research and progress in biomaterials used in 3D printing, there has been a rapid growth in applications of 3D printing in manufacturing customized implants, prostheses, drug delivery devices, and 3D scaffolds for tissue engineering and regenerative medicine. The current review focuses on the novel biomaterials used in variety of 3D printing technologies for clinical applications. Most common types of medical 3D printing technologies, including fused deposition modeling, extrusion based bioprinting, inkjet, and polyjet printing techniques, their clinical applications, different types of biomaterials currently used by researchers, and key limitations are discussed in detail.

Novel Biomaterials Used in Medical 3D Printing Techniques.

Science.gov (United States)

Tappa, Karthik; Jammalamadaka, Udayabhanu

2018-02-07

The success of an implant depends on the type of biomaterial used for its fabrication. An ideal implant material should be biocompatible, inert, mechanically durable, and easily moldable. The ability to build patient specific implants incorporated with bioactive drugs, cells, and proteins has made 3D printing technology revolutionary in medical and pharmaceutical fields. A vast variety of biomaterials are currently being used in medical 3D printing, including metals, ceramics, polymers, and composites. With continuous research and progress in biomaterials used in 3D printing, there has been a rapid growth in applications of 3D printing in manufacturing customized implants, prostheses, drug delivery devices, and 3D scaffolds for tissue engineering and regenerative medicine. The current review focuses on the novel biomaterials used in variety of 3D printing technologies for clinical applications. Most common types of medical 3D printing technologies, including fused deposition modeling, extrusion based bioprinting, inkjet, and polyjet printing techniques, their clinical applications, different types of biomaterials currently used by researchers, and key limitations are discussed in detail.

Virtual printer : an environment for digital print modeling and inspection

NARCIS (Netherlands)

Marchenko, V.

2014-01-01

Océ-Technologies B.V., a member of the Canon Group, specializes in providing solutions for enterprise printing, large format printing, and production printing. Software is an important part of a modern printer. One of the tasks for inkjet-printer software is to transform input print data into timed

5 CFR 532.279 - Special wage schedules for printing positions.

Science.gov (United States)

2010-01-01

... the printing survey as follows: (1) The lead agency must include North American Industry... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Special wage schedules for printing... printing positions. (a) The lead agency in a special printing schedule area listed in paragraph (j) of this...

Topography printing to locally control wettability.

Science.gov (United States)

Zheng, Zijian; Azzaroni, Omar; Zhou, Feng; Huck, Wilhelm T S

2006-06-21

This paper reports a new patterning method, which utilizes NaOH to facilitate the irreversible binding between the PDMS stamp and substrates and subsequent cohesive mechanical failure to transfer the PDMS patterns. Our method shows high substrate tolerance and can be used to "print" various PDMS geometries on a wide range of surfaces, including Si100, glass, gold, polymers, and patterned SU8 photoresist. Using this technique, we are able to locally change the wettability of substrate surfaces by printing well-defined PDMS architectures on the patterned SU8 photoresist. It is possible to generate differential wetting and dewetting properties in microchannels and in the PDMS printed area, respectively.

Three-dimensional Printing in Developing Countries.

Science.gov (United States)

Ibrahim, Ahmed M S; Jose, Rod R; Rabie, Amr N; Gerstle, Theodore L; Lee, Bernard T; Lin, Samuel J

2015-07-01

The advent of 3-dimensional (3D) printing technology has facilitated the creation of customized objects. The lack of regulation in developing countries renders conventional means of addressing various healthcare issues challenging. 3D printing may provide a venue for addressing many of these concerns in an inexpensive and easily accessible fashion. These may potentially include the production of basic medical supplies, vaccination beads, laboratory equipment, and prosthetic limbs. As this technology continues to improve and prices are reduced, 3D printing has the potential ability to promote initiatives across the entire developing world, resulting in improved surgical care and providing a higher quality of healthcare to its residents.

Relationships between nutrition-related knowledge, self-efficacy, and behavior for fifth grade students attending Title I and non-Title I schools.

Science.gov (United States)

Hall, Elisha; Chai, Weiwen; Albrecht, Julie A

2016-01-01

The Social Cognitive Theory (SCT) is a widely used theory for nutrition education programming. Better understanding the relationships between knowledge, self-efficacy, and behavior among children of various income levels can help to form and improve nutrition programs, particularly for socioeconomically disadvantaged youth. The purpose of this study was to determine the relationships between knowledge, self-efficacy, and behavior among fifth grade students attending Title I (≥40% of students receiving free or reduced school meals) and non-Title I schools (students receiving free or reduced school meals). A validated survey was completed by 55 fifth grade students from Title I and 122 from non-Title I schools. Differences in knowledge, self-efficacy, and behavior scores between groups were assessed using t test and adjusted for variations between participating schools. Regression analysis was used to determine the relationships between knowledge, self-efficacy, and behavior. In adjusted models, the Title I group had significantly lower scores on several knowledge items and summary knowledge (P = 0.04). The Title I group had significantly lower scores on several behavior variables including intakes of fruits (P = 0.02), vegetables (P = 0.0005), whole grains (P = 0.0003), and lean protein (P = 0.047), physical activity (P = 0.002) and summary behavior (P = 0.001). However the Title I group scored higher on self-efficacy for meal planning (P = 0.04) and choosing healthy snacks (P = 0.036). Both self-efficacy (β = 0.70, P knowledge (β = 0.35, P = 0.002) strongly predicted behavior; however, only self-efficacy remained significant in the Title I group (self-efficacy, β = 0.82, P = 0.0003; knowledge, β = 0.11, P = 0.59). Results demonstrate disparities in nutrition knowledge and behavior outcomes between students surveyed from Title I and non-Title I schools, suggesting more resources may be necessary for lower income populations

[Research progress on the technique and materials for three-dimensional bio-printing].

Science.gov (United States)

Yang, Runhuai; Chen, Yueming; Ma, Changwang; Wang, Huiqin; Wang, Shuyue

2017-04-01

Three-dimensional (3D) bio-printing is a novel engineering technique by which the cells and support materials can be manufactured to a complex 3D structure. Compared with other 3D printing methods, 3D bio-printing should pay more attention to the biocompatible environment of the printing methods and the materials. Aimed at studying the feature of the 3D bio-printing, this paper mainly focuses on the current research state of 3D bio-printing, with the techniques and materials of the bio-printing especially emphasized. To introduce current printing methods, the inkjet method, extrusion method, stereolithography skill and laser-assisted technique are described. The printing precision, process, requirements and influence of all the techniques on cell status are compared. For introduction of the printing materials, the cross-link, biocompatibility and applications of common bio-printing materials are reviewed and compared. Most of the 3D bio-printing studies are being remained at the experimental stage up to now, so the review of 3D bio-printing could improve this technique for practical use, and it could also contribute to the further development of 3D bio-printing.

Laser-assisted printing of alginate long tubes and annular constructs

International Nuclear Information System (INIS)

Yan Jingyuan; Huang Yong; Chrisey, Douglas B

2013-01-01

Laser-assisted printing such as laser-induced forward transfer has been well studied to pattern or fabricate two-dimensional constructs. In particular, laser printing has found increasing biomedical applications as an orifice-free cell and organ printing approach, especially for highly viscous biomaterials and biological materials. Unfortunately, there have been very few studies on the efficacy of three-dimensional printing performance of laser printing. This study has investigated the feasibility of laser tube printing and the effects of sodium alginate concentration and operating conditions such as the laser fluence and laser spot size on the printing quality during laser-assisted printing of alginate annular constructs (short tubes) with a nominal diameter of 3 mm. It is found that highly viscous materials such as alginate can be printed into well-defined long tubes and annular constructs. The tube wall thickness and tube outer diameter decrease with the sodium alginate concentration, while they first increase, then decrease and finally increase again with the laser fluence. The sodium alginate concentration dominates if the laser fluence is low, and the laser fluence dominates if the sodium alginate concentration is low. (paper)

Digital Dentistry — 3D Printing Applications

OpenAIRE

Zaharia Cristian; Gabor Alin-Gabriel; Gavrilovici Andrei; Stan Adrian Tudor; Idorasi Laura; Sinescu Cosmin; Negruțiu Meda-Lavinia

2017-01-01

Three-dimensional (3D) printing is an additive manufacturing method in which a 3D item is formed by laying down successive layers of material. 3D printers are machines that produce representations of objects either planned with a CAD program or scanned with a 3D scanner. Printing is a method for replicating text and pictures, typically with ink on paper. We can print different dental pieces using different methods such as selective laser sintering (SLS), stereolithography, fused deposition mo...

Application of autoradiography in finger print analysis

International Nuclear Information System (INIS)

Stverak, B.; Kopejtko, J.; Simek, J.

1983-01-01

In order to broaden the possibilities of developing latent finger prints a tracer technique has been developed using sup(110m)Ag and autoradiographic imaging. This method has been tested on glass, paper and certain plastics. On paper it is possible to visualize finger prints even after previous development using Ninhydrin. It is shown that usable finger prints may be obtained also from materials from which they cannot be obtained using classical methods, e.g., polyethylene and simulated leather. (author)

Cultural stereotypes in Nigerian print media advertisements ...

African Journals Online (AJOL)

Cultural stereotypes in Nigerian print media advertisements. ... Abstract. This study set out to examine the extent to which cultural stereotype roles are depicted in print advertisements in Nigeria. It specifically ... AJOL African Journals Online.

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 1732 ... Journal Home > Advanced Search > Browse Title Index ... Vol 10, No 3 (2007), An Audit Of Perioperative Cardiac Arrest At ... Vol 11, No 4 (2008), An Audit Of Rejected Repeated X-ray Films As A Quality Assurance ...

3D inkjet printed flexible and wearable antenna systems

KAUST Repository

Shamim, Atif

2017-01-01

extremely low cost, to the extent that they become disposable. The flexible and low cost aspects can be addressed by adapting additive manufacturing technologies such as inkjet printing and 3D printing. This paper presents inkjet printing as an emerging new

Cibachrome testing. [photographic processing and printing materials

Science.gov (United States)

Weinstein, M. S.

1974-01-01

The use of Cibachrome products as a solution to problems encountered when contact printing Kodak film type SO-397 onto Kodak Ektrachrome color reversal paper type 1993 is investigated. A roll of aerial imagery consisting of Kodak film types SO-397 and 2443 was contact printed onto Cibachrome and Kodak materials and compared in terms of color quality, resolution, cost, and compatibility with existing equipment and techniques. Objective measurements are given in terms of resolution and sensitometric response. Comparison prints and transparencies were viewed and ranked according to overall quality and aesthetic appeal. It is recommended that Cibachrome Print material be used in place of Kodak Ektachrome paper because it is more easily processed, the cost is equivalent, and it provides improved resolution, color quality, and image fade resistance.

Effect of layer thickness and printing orientation on mechanical properties and dimensional accuracy of 3D printed porous samples for bone tissue engineering.

Directory of Open Access Journals (Sweden)

Arghavan Farzadi

Full Text Available Powder-based inkjet 3D printing method is one of the most attractive solid free form techniques. It involves a sequential layering process through which 3D porous scaffolds can be directly produced from computer-generated models. 3D printed products' quality are controlled by the optimal build parameters. In this study, Calcium Sulfate based powders were used for porous scaffolds fabrication. The printed scaffolds of 0.8 mm pore size, with different layer thickness and printing orientation, were subjected to the depowdering step. The effects of four layer thicknesses and printing orientations, (parallel to X, Y and Z, on the physical and mechanical properties of printed scaffolds were investigated. It was observed that the compressive strength, toughness and Young's modulus of samples with 0.1125 and 0.125 mm layer thickness were more than others. Furthermore, the results of SEM and μCT analyses showed that samples with 0.1125 mm layer thickness printed in X direction have more dimensional accuracy and significantly close to CAD software based designs with predefined pore size, porosity and pore interconnectivity.

Special Issue: 3D Printing for Biomedical Engineering.

Science.gov (United States)

Chua, Chee Kai; Yeong, Wai Yee; An, Jia

2017-02-28

Three-dimensional (3D) printing has a long history of applications in biomedical engineering. The development and expansion of traditional biomedical applications are being advanced and enriched by new printing technologies. New biomedical applications such as bioprinting are highly attractive and trendy. This Special Issue aims to provide readers with a glimpse of the recent profile of 3D printing in biomedical research.

3D Printed Block Copolymer Nanostructures

Science.gov (United States)

Scalfani, Vincent F.; Turner, C. Heath; Rupar, Paul A.; Jenkins, Alexander H.; Bara, Jason E.

2015-01-01

The emergence of 3D printing has dramatically advanced the availability of tangible molecular and extended solid models. Interestingly, there are few nanostructure models available both commercially and through other do-it-yourself approaches such as 3D printing. This is unfortunate given the importance of nanotechnology in science today. In this…

3D Printing by Multiphase Silicone/Water Capillary Inks

NARCIS (Netherlands)

Roh, Sangchul; Parekh, Dishit P.; Bharti, Bhuvnesh; Stoyanov, Simeon D.; Velev, Orlin D.

2017-01-01

3D printing of polymers is accomplished easily with thermoplastics as the extruded hot melt solidifies rapidly during the printing process. Printing with liquid polymer precursors is more challenging due to their longer curing times. One curable liquid polymer of specific interest is

Screen-printing ink transfer in a sexual assault case.

Science.gov (United States)

Amick, Janeice F; Beheim, Chris W

2002-05-01

Yellow plastic-like particles were discovered on the clothing and body of a sexual assault victim. These particles were later associated to an athletic jersey with flaking yellow screen-printed numbers and letters, worn by the suspect. Depending on its intended substrate, screen-print ink can vary in color and composition. Particles dislodged from screen-printed garments may exhibit fabric impressions. Screen-printed clothing, commonly encountered in forensic casework, should be viewed as a potential source of trace evidence.

3D Printing and 3D Bioprinting in Pediatrics.

Science.gov (United States)

Vijayavenkataraman, Sanjairaj; Fuh, Jerry Y H; Lu, Wen Feng

2017-07-13

Additive manufacturing, commonly referred to as 3D printing, is a technology that builds three-dimensional structures and components layer by layer. Bioprinting is the use of 3D printing technology to fabricate tissue constructs for regenerative medicine from cell-laden bio-inks. 3D printing and bioprinting have huge potential in revolutionizing the field of tissue engineering and regenerative medicine. This paper reviews the application of 3D printing and bioprinting in the field of pediatrics.

3D Printing and 3D Bioprinting in Pediatrics

OpenAIRE

Vijayavenkataraman, Sanjairaj; Fuh, Jerry Y H; Lu, Wen Feng

2017-01-01

Additive manufacturing, commonly referred to as 3D printing, is a technology that builds three-dimensional structures and components layer by layer. Bioprinting is the use of 3D printing technology to fabricate tissue constructs for regenerative medicine from cell-laden bio-inks. 3D printing and bioprinting have huge potential in revolutionizing the field of tissue engineering and regenerative medicine. This paper reviews the application of 3D printing and bioprinting in the field of pediatrics.

The future of 3D printing technology in biomedicine

OpenAIRE

Iraj Nabipour

2015-01-01

3D printing, one of the hottest cutting-edge interdisciplinary technologies, is projected to have revenue of $8.4 billion in 2020. #D printing technology will implement the concept of personalized medicine in medical healthcare industry and pharmaceutical fabrication. Organ printing, which it is defined as computer-aided, jet based 3D tissue-engineering of living human organs, is an interesting and challengeable field for 3D printing. Customized implants and prostheses can be produced in any ...

Print vs digital the future of coexistence

CERN Document Server

Lee, Sul H

2013-01-01

Libraries are currently confronted by the challenges of managing increasing amounts of electronic information. Print vs. Digital: The Future of Coexistence presents the expert perspectives of eight of America's leading library administrators on ways to effectively manage digital flow and offers strategies to provide a level of coexistence between digital and print information. This excellent overview explores how to best balance print and electronic resources, and explores important issues such as the selection of electronic resources, improving access to digital information for a larger user

Enhanced multimaterial 4D printing with active hinges

Science.gov (United States)

Akbari, Saeed; Hosein Sakhaei, Amir; Kowsari, Kavin; Yang, Bill; Serjouei, Ahmad; Yuanfang, Zhang; Ge, Qi

2018-06-01

Despite great progress in four-dimensional (4D) printing, i.e. three-dimensional (3D) printing of active (stimuli-responsive) materials, the relatively low actuation force of the 4D printed structures often impedes their engineering applications. In this study, we use multimaterial inkjet 3D printing technology to fabricate shape memory structures, including a morphing wing flap and a deployable structure, which consist of active and flexible hinges joining rigid (non-active) parts. The active hinges, printed from a shape memory polymer (SMP), lock the structure into a second temporary shape during a thermomechanical programming process, while the flexible hinges, printed from an elastomer, effectively increase the actuation force and the load-bearing capacity of the printed structure as reflected in the recovery ratio. A broad range of mechanical properties such as modulus and failure strain can be achieved for both active and flexible hinges by varying the composition of the two base materials, i.e. the SMP and the elastomer, to accommodate large deformation induced during programming step, and enhance the recovery in the actuating step. To find the important design parameters, including local deformation, shape fixity and recovery ratio, we conduct high fidelity finite element simulations, which are able to accurately predict the nonlinear deformation of the printed structures. In addition, a coupled thermal-electrical finite element analysis was performed to model the heat transfer within the active hinges during the localized Joule heating process. The model predictions showed good agreement with the measured temperature data and were used to find the major parameters affecting temperature distribution including the applied voltage and the convection rate.

Printing technologies in fabrication of drug delivery systems.

Science.gov (United States)

Kolakovic, Ruzica; Viitala, Tapani; Ihalainen, Petri; Genina, Natalja; Peltonen, Jouko; Sandler, Niklas

2013-12-01

There has been increased activity in the field recently regarding the development and research on various printing techniques in fabrication of dosage forms and drug delivery systems. These technologies may offer benefits and flexibility in manufacturing, potentially paving the way for personalized dosing and tailor-made dosage forms. In this review, the most recent observations and advancements in fabrication of drug delivery systems by utilizing printing technologies are summarized. A general overview of 2D printing techniques is presented including a review of the most recent literature where printing techniques are used in fabrication of drug delivery systems. The future perspectives and possible impacts on formulation strategies, flexible dosing and personalized medication of using printing techniques for fabrication of drug delivery systems are discussed. It is evident that there is an urgent need to meet the challenges of rapidly growing trend of personalization of medicines through development of flexible drug-manufacturing approaches. In this context, various printing technologies, such as inkjet and flexography, can play an important role. Challenges on different levels exist and include: i) technological development of printers and production lines; ii) printable formulations and carrier substrates; iii) quality control and characterization; and iv) regulatory perspectives.

Land Titles and Rice Production in Vietnam

DEFF Research Database (Denmark)

Van Den Broeck, Katleen; Newman, Carol; Tarp, Finn

analysis of plot level rice yields that land titles are indeed important. Only exclusively held titles have the expected positive effects, and the positive effect on yields is found in male headed households. Furthermore, a household level rice yield function reveals that exclusive user rights...

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 221 ... Issue, Title ... Vol 38 (2010), Soft drink consumption of Grade 4 and Grade 7 learners in the Wynberg area, City of Cape Town, South .... Vol 42 (2014), The meaning of food for obese men: a qualitative study, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 151 - 200 of 1020 ... Issue, Title ... Vol 48, No 2 (2006), Barriers to HIV Care and Treatment by Doctors: A review of the literature. ... Vol 48, No 5 (2006), Breast cancer – early detection and screening in South African women from the ...

3D Printed Photoresponsive Devices Based on Shape Memory Composites.

Science.gov (United States)

Yang, Hui; Leow, Wan Ru; Wang, Ting; Wang, Juan; Yu, Jiancan; He, Ke; Qi, Dianpeng; Wan, Changjin; Chen, Xiaodong

2017-09-01

Compared with traditional stimuli-responsive devices with simple planar or tubular geometries, 3D printed stimuli-responsive devices not only intimately meet the requirement of complicated shapes at macrolevel but also satisfy various conformation changes triggered by external stimuli at the microscopic scale. However, their development is limited by the lack of 3D printing functional materials. This paper demonstrates the 3D printing of photoresponsive shape memory devices through combining fused deposition modeling printing technology and photoresponsive shape memory composites based on shape memory polymers and carbon black with high photothermal conversion efficiency. External illumination triggers the shape recovery of 3D printed devices from the temporary shape to the original shape. The effect of materials thickness and light density on the shape memory behavior of 3D printed devices is quantified and calculated. Remarkably, sunlight also triggers the shape memory behavior of these 3D printed devices. This facile printing strategy would provide tremendous opportunities for the design and fabrication of biomimetic smart devices and soft robotics. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Print mass media: territory of survival

Directory of Open Access Journals (Sweden)

Evgeny V. Akhmadulin

2016-09-01

Full Text Available The article is devoted to the problem of the survival of the print media in the information market in the conditions of intense competition with online journalism and the whole information flow on the Internet. Despite the predictions of the impending death of print periodicals, more than half of the world adult population read a daily newspaper. At the same time, the trends taking place in the media market, confirm the reduction of print media segment in favor of the Internet. According to TNS-Russia data, only in 2013 the Internet audience has grown by 6 %. At the same time the circulation of print media in the US fell by 15 % in 2008- 2014, in Western Europe – by a quarter. In Russia, subscription circulation periodicals in the second half of 2014 fell by 20.2 %, and on the basis of subscription for the first half of 2015, the national average – 22 % (data of Federal State Unitary Enterprise “Russian Post”. Finding ways to stabilize the fall of the print media, many US publishing houses see the transition from advertcentric business model to consumcentric model. It is necessary to use the specifics and advantages of newspapers and magazines (comfort, media planning logic, analytic, continuity and consistency of the content of individual and hypertext editions, and others to maintain the intellectual elite. Print media targeting to an elite audience (willing to pay for exclusiveness allows publishers to offset the rising cost of issuing paperbased, and consumers (subscribers will give a sense of communion to a certain social community, receiving verified and thorough information. In this case, the subscription to a newspaper or magazine (no retail outlet and online will be fashionable factor of association of elite communities and acquire new qualitative features in the development of civil society.

3-D printed composites with ultrasonically arranged complex microstructure

Science.gov (United States)

Llewellyn-Jones, Thomas M.; Drinkwater, Bruce W.; Trask, Richard S.

2016-04-01

This paper demonstrates the efficacy of implementing ultrasonic manipulation within a modified form of stereolithographic 3D printing to form complex microstructures in printed components. Currently 3D printed components are limited both in terms of structural performance and specialised functionality. This study aims to demonstrate a novel method for 3D printing composite materials, by arranging microparticles suspended within a photocurable resin. The resin is selectively cured by a 3-axis gantry-mounted 405nm laser. Ultrasonic forces are used to arrange the microfibres into predetermined patterns within the resin, with unidirectional microfibre alignment and a hexagonal lattice structure demonstrated. An example of dynamic microstructure variation within a single print layer is also presented.

Clinical and academic use of electronic and print books: the Health Sciences Library System e-book study at the University of Pittsburgh.

Science.gov (United States)

Folb, Barbara L; Wessel, Charles B; Czechowski, Leslie J

2011-07-01

The purpose of the Health Sciences Library System (HSLS) electronic book (e-book) study was to assess use, and factors affecting use, of e-books by all patron groups of an academic health sciences library serving both university and health system-affiliated patrons. A web-based survey was distributed to a random sample (n=5,292) of holders of library remote access passwords. A total of 871 completed and 108 partially completed surveys were received, for an approximate response rate of 16.5%-18.5%, with all user groups represented. Descriptive and chi-square analysis was done using SPSS 17. Library e-books were used by 55.4% of respondents. Use by role varied: 21.3% of faculty reported having assigned all or part of an e-book for class readings, while 86% of interns, residents, and fellows reported using an e-book to support clinical care. Respondents preferred print for textbooks and manuals and electronic format for research protocols, pharmaceutical, and reference books, but indicated high flexibility about format choice. They rated printing and saving e-book content as more important than annotation, highlighting, and bookmarking features. Respondents' willingness to use alternate formats, if convenient, suggests that libraries can selectively reduce title duplication between print and e-books and still support library user information needs, especially if publishers provide features that users want. Marketing and user education may increase use of e-book collections.

Clinical and academic use of electronic and print books: the Health Sciences Library System e-book study at the University of Pittsburgh

Science.gov (United States)

Wessel, Charles B; Czechowski, Leslie J

2011-01-01

Objectives: The purpose of the Health Sciences Library System (HSLS) electronic book (e-book) study was to assess use, and factors affecting use, of e-books by all patron groups of an academic health sciences library serving both university and health system–affiliated patrons. Methods: A web-based survey was distributed to a random sample (n = 5,292) of holders of library remote access passwords. A total of 871 completed and 108 partially completed surveys were received, for an approximate response rate of 16.5%–18.5%, with all user groups represented. Descriptive and chi-square analysis was done using SPSS 17. Results: Library e-books were used by 55.4% of respondents. Use by role varied: 21.3% of faculty reported having assigned all or part of an e-book for class readings, while 86% of interns, residents, and fellows reported using an e-book to support clinical care. Respondents preferred print for textbooks and manuals and electronic format for research protocols, pharmaceutical, and reference books, but indicated high flexibility about format choice. They rated printing and saving e-book content as more important than annotation, highlighting, and bookmarking features. Conclusions: Respondents' willingness to use alternate formats, if convenient, suggests that libraries can selectively reduce title duplication between print and e-books and still support library user information needs, especially if publishers provide features that users want. Marketing and user education may increase use of e-book collections. PMID:21753914

3D printing: making things at the library.

Science.gov (United States)

Hoy, Matthew B

2013-01-01

3D printers are a new technology that creates physical objects from digital files. Uses for these printers include printing models, parts, and toys. 3D printers are also being developed for medical applications, including printed bone, skin, and even complete organs. Although medical printing lags behind other uses for 3D printing, it has the potential to radically change the practice of medicine over the next decade. Falling costs for hardware have made 3D printers an inexpensive technology that libraries can offer their patrons. Medical librarians will want to be familiar with this technology, as it is sure to have wide-reaching effects on the practice of medicine.

A combined system for 3D printing cybersecurity

Science.gov (United States)

Straub, Jeremy

2017-06-01

Previous work has discussed the impact of cybersecurity breaches on 3D printed objects. Multiple attack types that could weaken objects, make them unsuitable for certain applications and even create safety hazards have been presented. This paper considers a visible light sensing-based verification system's efficacy as a means of thwarting cybersecurity threats to 3D printing. This system detects discrepancies between expected and actual printed objects (based on an independent pristine CAD model). Whether reliance on an independent CAD model is appropriate is also considered. The future of 3D printing is projected and the importance of cybersecurity in this future is discussed.

Use of nanocellulose in printed electronics: a review

Science.gov (United States)

Hoeng, Fanny; Denneulin, Aurore; Bras, Julien

2016-07-01

Since the last decade, interest in cellulose nanomaterials known as nanocellulose has been growing. Nanocellulose has various applications ranging from composite reinforcement to rheological modifiers. Recently, nanocellulose has been shown to have great potential in flexible printed electronics applications. The property of nanocellulose to form self-standing thermally stable films has been exploited for producing transparent and smooth substrates for printed electronics. However, other than substrates, the field of printed electronics involves the use of inks, various processing methods and the production of flexible electronic devices. This review aims at providing an overview of the use and potential of nanocellulose throughout the printed electronics field.

Continuous tone printing in silicone from CNC milled matrices

Science.gov (United States)

Hoskins, S.; McCallion, P.

2014-02-01

Current research at the Centre for Fine Print Research (CFPR) at the University of the West of England, Bristol, is exploring the potential of creating coloured pictorial imagery from a continuous tone relief surface. To create the printing matrices the research team have been using CNC milled images where the height of the relief image is dictated by creating a tone curve and then milling this curve into a series of relief blocks from which the image is cast in a silicone ink. A translucent image is cast from each of the colour matrices and each colour is assembled - one on top of another - resulting is a colour continuous tone print, where colour tone is created by physical depth of colour. This process is a contemporary method of continuous tone colour printing based upon the Nineteenth Century black and white printing process of Woodburytype as developed by Walter Bentley Woodbury in 1865. Woodburytype is the only true continuous tone printing process invented, and although its delicate and subtle surfaces surpassed all other printing methods at the time. The process died out in the late nineteenth century as more expedient and cost effective methods of printing prevailed. New research at CFPR builds upon previous research that combines 19th Century Photomechanical techniques with digital technology to reappraise the potential of these processes.

Printed microfluidic filter for heparinized blood.

Science.gov (United States)

Bilatto, Stanley E R; Adly, Nouran Y; Correa, Daniel S; Wolfrum, Bernhard; Offenhäusser, Andreas; Yakushenko, Alexey

2017-05-01

A simple lab-on-a-chip method for blood plasma separation was developed by combining stereolithographic 3D printing with inkjet printing, creating a completely sealed microfluidic device. In some approaches, one dilutes the blood sample before separation, reducing the concentration of a target analyte and increasing a contamination risk. In this work, a single drop (8  μ l) of heparinized whole blood could be efficiently filtered using a capillary effect without any external driving forces and without dilution. The blood storage in heparin tubes during 24 h at 4 °C initiated the formation of small crystals that formed auto-filtration structures in the sample upon entering the 3D-printed device, with pores smaller than the red blood cells, separating plasma from the cellular content. The total filtration process took less than 10 s. The presented printed plasma filtration microfluidics fabricated with a rapid prototyping approach is a miniaturized, fast and easy-to-operate device that can be integrated into healthcare/portable systems for point-of-care diagnostics.

3D printing of surgical instruments for long-duration space missions.

Science.gov (United States)

Wong, Julielynn Y; Pfahnl, Andreas C

2014-07-01

The first off-Earth fused deposition modeling (FDM) 3D printer will explore thermoplastic manufacturing capabilities in microgravity. This study evaluated the feasibility of FDM 3D printing 10 acrylonitrile butadiene styrene (ABS) thermoplastic surgical instruments on Earth. Three-point bending tests compared stiffness and yield strength between FDM 3D printed and conventionally manufactured ABS thermoplastic. To evaluate the relative speed of using four printed instruments compared to conventional instruments, 13 surgeons completed simulated prepping, draping, incising, and suturing tasks. Each surgeon ranked the performance of six printed instruments using a 5-point Likert scale. At a thickness of 5.75 mm or more, the FDM printing process had a less than 10% detrimental effect on the tested yield strength and stiffness of horizontally printed ABS thermoplastic relative to conventional ABS thermoplastic. Significant weakness was observed when a bending load was applied transversely to a 3D printed layer. All timed tasks were successfully performed using a printed sponge stick, towel clamp, scalpel handle, and toothed forceps. There was no substantial difference in time to completion of simulated surgical tasks with control vs. 3D printed instruments. Of the surgeons, 100%, 92%, 85%, 77%, 77%, and 69% agreed that the printed smooth and tissue forceps, curved and straight hemostats, tissue and right angle clamps, respectively, would perform adequately. It is feasible to 3D print ABS thermoplastic surgical instruments on Earth. Loadbearing structures were designed to be thicker, when possible. Printing orientations were selected so that the printing layering direction of critical structures would not be transverse to bending loads.

Special Issue: 3D Printing for Biomedical Engineering

Directory of Open Access Journals (Sweden)

Chee Kai Chua

2017-02-01

Full Text Available Three-dimensional (3D printing has a long history of applications in biomedical engineering. The development and expansion of traditional biomedical applications are being advanced and enriched by new printing technologies. New biomedical applications such as bioprinting are highly attractive and trendy. This Special Issue aims to provide readers with a glimpse of the recent profile of 3D printing in biomedical research.

Print quality challenges for the next decade

Science.gov (United States)

Meyer, John D.

1990-07-01

The decade of the eighties has seen a remarkable transformation in the performance and capabilities of shared and personal printers. Dramatic gains have been made in four key areas: cost, throughput, reliability and most significantly, print quality. The improvements in text print quality due to algorithmic fonts and increased resolution have been pivotal in the creation of the desktop publishing market. Electronic pre-press systems now include hardware to receive Postscript files accompanied by color originals for scanning and separation. These systems have application in the commercial printing of a wide variety of material e.g. books, magazines, brochures, newspapers. The vision of the future of hardcopy now embraces the full spectrum from typeset text to full color reproduction of natural images due to the advent of grayscale and color capability in printer technology. This will place increased demands for improvements in print quality, particularly in the use of grayscale and color. This paper gives an overview of the challenges which must be met and discusses data communication standards and print quality measurement techniques as a means of meeting these challenges for both color and black and white output.

THE DISTRIBUTION NETWORK DEVELOPEMENT IN PRINT MEDIA

Directory of Open Access Journals (Sweden)

Loredana Iordache

2012-09-01

Full Text Available In this article, we identify the characteristics of the distribution networks in print media and the features ofmarketing in mass media, emphasising the attempts initiated by the press in the context of the financial crisis. Theresearch was conducted through a case study on regional newspaper,, Gazeta de Sud'' The main problems analyzedwere decreasing newspaper circulation and advertising. The research taken into account trends and developmentsworldwide print media as well as print media particularities of Romania, with a focus on identifying factors thatcontributed to the closure of a significant number of newspapers, or their transition from printed version online format.The paper is mainly focused on some practical issues related to the way of organizing the print media sales networks,the authors elaborating proposals for the implementation of certain measures to increase the circulation, on the onehand, and on the hand, to increase the sale of ad space in the newspaper. Compared with other products, thenewspaper has unique characteristics caused by daily changing content, and therefore the product itself. Having ahighly perishable, the content of media products should always seen in relation to time, which requires more rapiddistribution and continuous production.

Inkjet-Printed Biofunctional Thermo-Plasmonic Interfaces for Patterned Neuromodulation.

Science.gov (United States)

Kang, Hongki; Lee, Gu-Haeng; Jung, Hyunjun; Lee, Jee Woong; Nam, Yoonkey

2018-02-27

Localized heat generation by the thermo-plasmonic effect of metal nanoparticles has great potential in biomedical engineering research. Precise patterning of the nanoparticles using inkjet printing can enable the application of the thermo-plasmonic effect in a well-controlled way (shape and intensity). However, a universally applicable inkjet printing process that allows good control in patterning and assembly of nanoparticles with good biocompatibility is missing. Here we developed inkjet-printing-based biofunctional thermo-plasmonic interfaces that can modulate biological activities. We found that inkjet printing of plasmonic nanoparticles on a polyelectrolyte layer-by-layer substrate coating enables high-quality, biocompatible thermo-plasmonic interfaces across various substrates (rigid/flexible, hydrophobic/hydrophilic) by induced contact line pinning and electrostatically assisted nanoparticle assembly. We experimentally confirmed that the generated heat from the inkjet-printed thermo-plasmonic patterns can be applied in micrometer resolution over a large area. Lastly, we demonstrated that the patterned thermo-plasmonic effect from the inkjet-printed gold nanorods can selectively modulate neuronal network activities. This inkjet printing process therefore can be a universal method for biofunctional thermo-plasmonic interfaces in various bioengineering applications.

Exploring New Directions: Title I in the Year 2000.

Science.gov (United States)

Puma, Michael J.; Drury, Darrel W.

This report takes stock of the present Title I program, identifies the most promising approaches to educating the nation's disadvantaged children, and offers guidance to policymakers seeking to improve Title I's effectiveness. The report draws upon hundreds of studies, evaluations, and other documents, and details the evolution of the Title I…

Second generation anthropomorphic physical phantom for mammography and DBT: Incorporating voxelized 3D printing and inkjet printing of iodinated lesion inserts

Science.gov (United States)

Sikaria, Dhiraj; Musinsky, Stephanie; Sturgeon, Gregory M.; Solomon, Justin; Diao, Andrew; Gehm, Michael E.; Samei, Ehsan; Glick, Stephen J.; Lo, Joseph Y.

2016-03-01

Physical phantoms are needed for the evaluation and optimization of new digital breast tomosynthesis (DBT) systems. Previously, we developed an anthropomorphic phantom based on human subject breast CT data and fabricated using commercial 3D printing. We now present three key advancements: voxelized 3D printing, photopolymer material doping, and 2D inkjet printing of lesion inserts. First, we bypassed the printer's control software in order to print in voxelized form instead of conventional STL surfaces, thus improving resolution and allowing dithering to mix the two photopolymer materials into arbitrary proportions. We demonstrated ability to print details as small as 150μm, and dithering to combine VeroWhitePlus and TangoPlus in 10% increments. Second, to address the limited attenuation difference among commercial photopolymers, we evaluated a beta sample from Stratasys with increased TiO2 doping concentration up to 2.5%, which corresponded to 98% breast density. By spanning 36% to 98% breast density, this doubles our previous contrast. Third, using inkjet printers modified to print with iopamidol, we created 2D lesion patterns on paper that can be sandwiched into the phantom. Inkjet printing has advantages of being inexpensive and easy, and more contrast can be delivered through overprinting. Printing resolution was maintained at 210 μm horizontally and 330 μm vertically even after 10 overprints. Contrast increased linearly with overprinting at 0.7% per overprint. Together, these three new features provide the basis for creating a new anthropomorphic physical breast phantom with improved resolution and contrast, as well as the ability to insert 2D lesions for task-based assessment of performance.

Screen-printed nanoparticles as anti-counterfeiting tags

Science.gov (United States)

Campos-Cuerva, Carlos; Zieba, Maciej; Sebastian, Victor; Martínez, Gema; Sese, Javier; Irusta, Silvia; Contamina, Vicente; Arruebo, Manuel; Santamaria, Jesus

2016-03-01

Metallic nanoparticles with different physical properties have been screen printed as authentication tags on different types of paper. Gold and silver nanoparticles show unique optical signatures, including sharp emission bandwidths and long lifetimes of the printed label, even under accelerated weathering conditions. Magnetic nanoparticles show distinct physical signals that depend on the size of the nanoparticle itself. They were also screen printed on different substrates and their magnetic signals read out using a magnetic pattern recognition sensor and a vibrating sample magnetometer. The novelty of our work lies in the demonstration that the combination of nanomaterials with optical and magnetic properties on the same printed support is possible, and the resulting combined signals can be used to obtain a user-configurable label, providing a high degree of security in anti-counterfeiting applications using simple commercially-available sensors.

Predicting transmittance spectra of electrophotographic color prints

Science.gov (United States)

Mourad, Safer; Emmel, Patrick; Hersch, Roger D.

2000-12-01

For dry toner electrophotographic color printers, we present a numerical simulation model describing the color printer responses based on a physical characterization of the different electrophotographic process steps. The proposed model introduces a Cross Transfer Efficiency designed to predict the color transmittance spectra of multi-color prints by taking into account the transfer influence of each deposited color toner layer upon the other layers. The simulation model leads to a better understanding of the factors that have an impact on printing quality. In order to avoid the additional optical non-linearities produced by light reflection on paper, we have limited the present investigation to transparency prints. The proposed model succeeded to predict the transmittance spectra of printed wedges combining two color toner layers with a mean deviation less than CIE-LAB (Delta) E equals 2.5.

Recent development in 3D food printing.

Science.gov (United States)

Yang, Fan; Zhang, Min; Bhandari, Bhesh

2017-09-22

Robots and software have been significantly improving our daily lives by rendering us much convenience. And 3D printing is a typical example, for it is going to usher in a new era of localized manufacturing that is actually based on digital fabrication by layer-by-layer deposition in three-dimensional space. In terms of food industry, the revolution that three-dimensional printing technologies is bringing to food manufacturing is convenience of low-cost customized fabrication and even precise nutrition control. This paper is aimed to give a brief introduction of recent development of food printing and material property of food ingredients that can be used to design the 3D food matrix and investigate the relationship between process parameters and resulting printed food properties in order to establish a food manufacturing process with this new food production approach.

24 CFR 232.595 - Eligibility of title.

Science.gov (United States)

2010-04-01

... URBAN DEVELOPMENT MORTGAGE AND LOAN INSURANCE PROGRAMS UNDER NATIONAL HOUSING ACT AND OTHER AUTHORITIES MORTGAGE INSURANCE FOR NURSING HOMES, INTERMEDIATE CARE FACILITIES, BOARD AND CARE HOMES, AND ASSISTED... Fire Safety Equipment Title § 232.595 Eligibility of title. In order for the property which is to be...

Evaluation of Photocrosslinked Lutrol Hydrogel for Tissue Printing applications

NARCIS (Netherlands)

Fedorovich, Natalja E.; Swennen, Ives; Girones, Jordi; Moroni, Lorenzo; van Blitterswijk, Clemens; Schacht, Etienne; Alblas, Jacqueline; Dhert, Wouter J.A.

2009-01-01

Application of hydrogels in tissue engineering and innovative strategies such as organ printing, which is based on layered 3D deposition of cell-laden hydrogels, requires design of novel hydrogel matrices. Hydrogel demands for 3D printing include: 1) preservation of the printed shape after the

Inkjet Printing of 3D Metallic Silver Complex Microstructures

NARCIS (Netherlands)

Wits, Wessel Willems; Sridhar, Ashok; Dimitrov, D.

2010-01-01

To broaden the scope of inkjet printing, this paper focuses on printing of an organic silver complex ink on glass substrates towards the fabrication of metallic 3D microstructures. The droplet formation sequence of the inkjet printer is optimised to print continuous layers of metal. A brief

14 CFR 221.195 - Requirement for filing printed material.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Requirement for filing printed material... filing printed material. (a) Any tariff, or revision thereto, filed in paper format which accompanies... supporting paper tariff, except as authorized by the Department. (b) Any printed justifications, or other...

Optical fabrication of lightweighted 3D printed mirrors

Science.gov (United States)

Herzog, Harrison; Segal, Jacob; Smith, Jeremy; Bates, Richard; Calis, Jacob; De La Torre, Alyssa; Kim, Dae Wook; Mici, Joni; Mireles, Jorge; Stubbs, David M.; Wicker, Ryan

2015-09-01

Direct Metal Laser Sintering (DMLS) and Electron Beam Melting (EBM) 3D printing technologies were utilized to create lightweight, optical grade mirrors out of AlSi10Mg aluminum and Ti6Al4V titanium alloys at the University of Arizona in Tucson. The mirror prototypes were polished to meet the λ/20 RMS and λ/4 P-V surface figure requirements. The intent of this project was to design topologically optimized mirrors that had a high specific stiffness and low surface displacement. Two models were designed using Altair Inspire software, and the mirrors had to endure the polishing process with the necessary stiffness to eliminate print-through. Mitigating porosity of the 3D printed mirror blanks was a challenge in the face of reconciling new printing technologies with traditional optical polishing methods. The prototypes underwent Hot Isostatic Press (HIP) and heat treatment to improve density, eliminate porosity, and relieve internal stresses. Metal 3D printing allows for nearly unlimited topological constraints on design and virtually eliminates the need for a machine shop when creating an optical quality mirror. This research can lead to an increase in mirror mounting support complexity in the manufacturing of lightweight mirrors and improve overall process efficiency. The project aspired to have many future applications of light weighted 3D printed mirrors, such as spaceflight. This paper covers the design/fab/polish/test of 3D printed mirrors, thermal/structural finite element analysis, and results.

3D Printing of Molecular Models

Science.gov (United States)

Gardner, Adam; Olson, Arthur

2016-01-01

Physical molecular models have played a valuable role in our understanding of the invisible nano-scale world. We discuss 3D printing and its use in producing models of the molecules of life. Complex biomolecular models, produced from 3D printed parts, can demonstrate characteristics of molecular structure and function, such as viral self-assembly,…

Citation Oil and Gas Corporation... Title V Applicability Determination

Science.gov (United States)

This document may be of assistance in applying the Title V air operating permit regulations. This document is part of the Title V Policy and Guidance Database available at www2.epa.gov/title-v-operating-permits/title-v-operating-permit-policy-and-guidance-document-index. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

Embedding complex objects with 3d printing

KAUST Repository

Hussain, Muhammad Mustafa; Diaz, Cordero Marlon Steven

2017-01-01

A CMOS technology-compatible fabrication process for flexible CMOS electronics embedded during additive manufacturing (i.e. 3D printing). A method for such a process may include printing a first portion of a 3D structure; pausing the step

Patterned electrodeposition of interconnects using microcontact printing

NARCIS (Netherlands)

Hovestad, A.; Rendering, H.; Maijenburg, A.W.

2012-01-01

Microcontact printing combined with electroless deposition is a potential low cost technique to make electrical interconnects for opto-electronic devices. Microcontact printed inhibitors locally prevent electroless deposition resulting in a pre-defined pattern of metal tracks. The inhibition of

3D printing for soft robotics – a review

Science.gov (United States)

Gul, Jahan Zeb; Sajid, Memoon; Rehman, Muhammad Muqeet; Siddiqui, Ghayas Uddin; Shah, Imran; Kim, Kyung-Hwan; Lee, Jae-Wook; Choi, Kyung Hyun

2018-01-01

Abstract Soft robots have received an increasing attention due to their advantages of high flexibility and safety for human operators but the fabrication is a challenge. Recently, 3D printing has been used as a key technology to fabricate soft robots because of high quality and printing multiple materials at the same time. Functional soft materials are particularly well suited for soft robotics due to a wide range of stimulants and sensitive demonstration of large deformations, high motion complexities and varied multi-functionalities. This review comprises a detailed survey of 3D printing in soft robotics. The development of key 3D printing technologies and new materials along with composites for soft robotic applications is investigated. A brief summary of 3D-printed soft devices suitable for medical to industrial applications is also included. The growing research on both 3D printing and soft robotics needs a summary of the major reported studies and the authors believe that this review article serves the purpose. PMID:29707065

A review of non-contact micro- and nano-printing technologies

International Nuclear Information System (INIS)

Ru, Changhai; Sun, Yu; Luo, Jun; Xie, Shaorong

2014-01-01

Printing technologies have undergone signficant development because they are an enabler in science and engineering research; they also have significant practical applications in manufacturing. Micro- and nano-printing techniques have found a number of applications in electronics, biotechnology, and material synthesis/patterning. In this review, we look at the important printing methods, including high precision traditional printing methods as well as recently emerging techniques. We also discuss the materials that are printable by these technologies, the challenges for future development, and the applications of micro- and nano-printing. (topical review)

A review of non-contact micro- and nano-printing technologies

Science.gov (United States)

Ru, Changhai; Luo, Jun; Xie, Shaorong; Sun, Yu

2014-05-01

Printing technologies have undergone signficant development because they are an enabler in science and engineering research; they also have significant practical applications in manufacturing. Micro- and nano-printing techniques have found a number of applications in electronics, biotechnology, and material synthesis/patterning. In this review, we look at the important printing methods, including high precision traditional printing methods as well as recently emerging techniques. We also discuss the materials that are printable by these technologies, the challenges for future development, and the applications of micro- and nano-printing.

Browse Title Index

African Journals Online (AJOL)

Items 201 - 250 of 577 ... Issue, Title. Vol 20, No 2 (2003), Emergency Contraception: A Global Overview of Knowledge, Attitudes and Practices Among Providers, Abstract PDF. Deborah Haggai. Vol 23 (2006):, Emergency laparotomy for peripartum haemorrhage in Bida North Central Nigeria, Abstract PDF. Sunny Abiodun O ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 155 ... Issue, Title. Vol 12 (2012), Political Dissent and Autonomy in Wum Local Government, Southern (West) Cameroons, 1957 – 1968, Abstract. TP Mbeum. Vol 9 (2009), Post-Emancipation Slave Commerce: Increasing Child Slave Trafficking and Women's Agency in Late Nineteenth-century Ghana ...

24 CFR 203.386 - Coverage of title evidence.

Science.gov (United States)

2010-04-01

... SINGLE FAMILY MORTGAGE INSURANCE Contract Rights and Obligations Property Title Transfers and Title... the public records, there are not, at such date, any outstanding prior liens, including any past-due...

Printing of the year book, carton boxes and printed envelopes

Indian Academy of Sciences (India)

2018-01-18

Jan 18, 2018 ... Technology, Government of India needs the following book to be printed ... of the documents are not enclosed, the quotation will not be considered. ... The EMD of selected bidder will be kept as security deposit till ... via E-Mail.

Effect of Processing Parameters on 3D Printing of Cement - based Materials

Science.gov (United States)

Lin, Jia Chao; Wang, Jun; Wu, Xiong; Yang, Wen; Zhao, Ri Xu; Bao, Ming

2018-06-01

3D printing is a new study direction of building method in recent years. The applicability of 3D printing equipment and cement based materials is analyzed, and the influence of 3D printing operation parameters on the printing effect is explored in this paper. Results showed that the appropriate range of 3D printing operation parameters: print height/nozzle diameter is between 0.4 to 0.6, the printing speed 4-8 cm/s with pumpage 9 * 10-2 m 3/ h.

A Straightforward Approach for 3D Bacterial Printing.

Science.gov (United States)

Lehner, Benjamin A E; Schmieden, Dominik T; Meyer, Anne S

2017-07-21

Sustainable and personally tailored materials production is an emerging challenge to society. Living organisms can produce and pattern an extraordinarily wide range of different molecules in a sustainable way. These natural systems offer an abundant source of inspiration for the development of new environmentally friendly materials production techniques. In this paper, we describe the first steps toward the 3-dimensional printing of bacterial cultures for materials production and patterning. This methodology combines the capability of bacteria to form new materials with the reproducibility and tailored approach of 3D printing systems. For this purpose, a commercial 3D printer was modified for bacterial systems, and new alginate-based bioink chemistry was developed. Printing temperature, printhead speed, and bioink extrusion rate were all adapted and customized to maximize bacterial health and spatial resolution of printed structures. Our combination of 3D printing technology with biological systems enables a sustainable approach for the production of numerous new materials.

Meanings of Local Food in Danish Print Media

DEFF Research Database (Denmark)

Eriksen, Safania Normann

2014-01-01

. The article finds six major themes, which are central to the understanding of local food in Danish print media, namely ‘local food networks’, ‘food values’, ‘food system’, ‘food tourism’, ‘food events’ and ‘local food in supermarkets’. It concludes that there are important differences between print media......The purpose of this article is to find empirical evidence that can verify the seemingly new and growing interest in local food in Denmark, and shed light on what meanings the concept of local food holds in Danish print media. A content analysis of Danish print media is undertaken of articles...... reporting on local food over a 10-year period. A total of 993 articles are collected from national, regional and local newspapers as well as trade journals and magazines. Incorporating print media as agents in the construction of meanings of local food is a relatively understudied field of research...

24 CFR 234.65 - Nature of title.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Nature of title. 234.65 Section 234.65 Housing and Urban Development Regulations Relating to Housing and Urban Development (Continued... OWNERSHIP MORTGAGE INSURANCE Eligibility Requirements-Individually Owned Units § 234.65 Nature of title. A...

7 CFR 58.313 - Print and bulk packaging rooms.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Print and bulk packaging rooms. 58.313 Section 58.313 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....313 Print and bulk packaging rooms. Rooms used for packaging print or bulk butter and related products...

Effects of providing word sounds during printed word learning

NARCIS (Netherlands)

Reitsma, P.; Dongen, van A.J.N.; Custers, E.

1984-01-01

The purpose of this study was to explore the effects of the availability of the spoken sound of words along with the printed forms during reading practice. Firstgrade children from two normal elementary schools practised reading several unfamiliar words in print. For half of the printed words the

Structural Color Patterns by Electrohydrodynamic Jet Printed Photonic Crystals.

Science.gov (United States)

Ding, Haibo; Zhu, Cun; Tian, Lei; Liu, Cihui; Fu, Guangbin; Shang, Luoran; Gu, Zhongze

2017-04-05

In this work, we demonstrate the fabrication of photonic crystal patterns with controllable morphologies and structural colors utilizing electrohydrodynamic jet (E-jet) printing with colloidal crystal inks. The final shape of photonic crystal units is controlled by the applied voltage signal and wettability of the substrate. Optical properties of the structural color patterns are tuned by the self-assembly of the silica nanoparticle building blocks. Using this direct printing technique, it is feasible to print customized functional patterns composed of photonic crystal dots or photonic crystal lines according to relevant printing mode and predesigned tracks. This is the first report for E-jet printing with colloidal crystal inks. Our results exhibit promising applications in displays, biosensors, and other functional devices.

REAL TIME QUALITY CONTROL OF THE HEATSET OFFSET PRINTING PROCESS

Directory of Open Access Journals (Sweden)

Răzvan-George RĂCHERU

2016-05-01

Full Text Available Offset lithography is one of the most common ways of creating printed materials. Compared to other printing methods, offset printing is best suited for economically producing large volumes of high quality prints in a manner that requires little maintenance. Because of the high speed and the high volume of the printing press, we have to rely on automation for press control and not just to the printer’s eye. When printing an image that has more than one color, it is necessary to print each color separately and ensure each color overlaps the others precisely. If this is not done, the finished image will look fuzzy, blurred or "out of register". To help line the colors up correctly, a system of registration is necessary. Therefore, the use of an automated real time quality control system will result in a more consistent color for the customer and less waste for the printer.

Future enhancements to 3D printing and real time production

Science.gov (United States)

Landa, Joseph; Jenkins, Jeffery; Wu, Jerry; Szu, Harold

2014-05-01

The cost and scope of additive printing machines range from several hundred to hundreds of thousands of dollars. For the extra money, one can get improvements in build size, selection of material properties, resolution, and consistency. However, temperature control during build and fusing predicts outcome and protects the IP by large high cost machines. Support material options determine geometries that can be accomplished which drives cost and complexity of printing heads. Historically, 3D printers have been used for design and prototyping efforts. Recent advances and cost reduction sparked new interest in developing printed products and consumables such as NASA who is printing food, printing consumer parts (e.g. cell phone cases, novelty toys), making tools and fixtures in manufacturing, and recursively print a self-similar printer (c.f. makerbot). There is a near term promise of the capability to print on demand products at the home or office... directly from the printer to use.

Highly Conductive Nano-Silver Circuits by Inkjet Printing

Science.gov (United States)

Zhu, Dongbin; Wu, Minqiang

2018-06-01

Inkjet technology has become popular in the field of printed electronics due to its superior properties such as simple processes and printable complex patterns. Electrical conductivity of the circuits is one of the key factors in measuring the performance of printed electronics, which requires great material properties and a manufactured process. With excellent conductivity and ductility, silver is an ideal material as the wire connecting components. This review summarizes the progress of conductivity studies on inkjet printed nano-silver lines, including ink composition and nanoparticle morphology, deposition of nano-silver lines with uniform and high aspect ratios, sintering mechanisms and alternative methods of thermal sintering. Finally, the research direction on inkjet printed electronics is proposed.

Subwavelength Plasmonic Color Printing Protected for Ambient Use

DEFF Research Database (Denmark)

Roberts, Alexander Sylvester; Pors, Anders Lambertus; Albrektsen, Ole

2014-01-01

We demonstrate plasmonic color printing with subwavelength resolution using circular gap-plasmon resonators (GPRs) arranged in 340 nm period arrays of square unit cells and fabricated with single-step electron-beam lithography. We develop a printing procedure resulting in correct single-pixel color...... reproduction, high color uniformity of colored areas, and high reproduction fidelity. Furthermore, we demonstrate that, due to inherent stability of GPRs with respect to surfactants, the fabricated color print can be protected with a transparent dielectric overlay for ambient use without destroying its...... coloring. Using finite-element simulations, we uncover the physical mechanisms responsible for color printing with GPR arrays and suggest the appropriate design procedure minimizing the influence of the protection layer....

Browse Title Index

African Journals Online (AJOL)

Items 51 - 98 of 98 ... Issue, Title. Vol 4, No 1 (2016), First-year seminar intervention: Enhancing firstyear mathematics performance at the University of Johannesburg, Abstract PDF. Melanie Jacobs, Estherna Pretorius. Vol 5, No 2 (2017), From Inky Pinky Ponky to Improving Student Understanding in Assessment: Exploring the ...

Browse Title Index

African Journals Online (AJOL)

Items 551 - 600 of 1463 ... Issue, Title. Vol 15, No 2 (2015), Evaluation of the diagnostic performance and operational characteristics of four rapid immunochromatographic syphilis tests in Burkina Faso, Abstract PDF. FY Bocoum, H Ouedraogo, G Tarnagda, A Kiba, S Tiendrebeogo, F Bationo, B Liestman, S Diagbouga, ...

Browse Title Index

African Journals Online (AJOL)

Items 9951 - 10000 of 11090 ... Issue, Title. Vol 10, No 36 (2011), Study of heavy metals bioaccumulation in the process of vermicomposting, Abstract PDF. MM Aleagha, G Ebadi. Vol 10, No 45 (2011), Study of malondialdehyde (MDA) content, superoxide dismutase (SOD) and glutathione peroxidase (GSH-Px) activities in ...

Browse Title Index

African Journals Online (AJOL)

Items 101 - 150 of 985 ... Journal Home > Advanced Search > Browse Title Index ... Vol 17 (2010), Alternating Direction Implicit Finite Difference Time Domain Acoustic Wave Algorithm, Abstract. E Ikata .... Vol 17 (2010), Analytic derivation of the wave profile and phase speed of sixth order Stokes waves in deep water, Abstract.

Browse Title Index

African Journals Online (AJOL)

Items 451 - 500 of 581 ... Issue, Title. Vol 30, No 1 (2016), Risky sexual behaviour and associated factors among students of Debre Tabor University, Northwest Ethiopia: a cross-sectional study, Abstract PDF. Awoke Derbie, Mekonnen Assefa, Daniel Mekonnen, Fantahun Biadglegne. Vol 28, No 1 (2014), Road traffic accident: ...

The application of digital medical 3D printing technology on tumor operation

Science.gov (United States)

Chen, Jimin; Jiang, Yijian; Li, Yangsheng

2016-04-01

Digital medical 3D printing technology is a new hi-tech which combines traditional medical and digital design, computer science, bio technology and 3D print technology. At the present time there are four levels application: The printed 3D model is the first and simple application. The surgery makes use of the model to plan the processing before operation. The second is customized operation tools such as implant guide. It helps doctor to operate with special tools rather than the normal medical tools. The third level application of 3D printing in medical area is to print artificial bones or teeth to implant into human body. The big challenge is the fourth level which is to print organs with 3D printing technology. In this paper we introduced an application of 3D printing technology in tumor operation. We use 3D printing to print guide for invasion operation. Puncture needles were guided by printed guide in face tumors operation. It is concluded that this new type guide is dominantly advantageous.

Personalized development of human organs using 3D printing technology.

Science.gov (United States)

Radenkovic, Dina; Solouk, Atefeh; Seifalian, Alexander

2016-02-01

3D printing is a technique of fabricating physical models from a 3D volumetric digital image. The image is sliced and printed using a specific material into thin layers, and successive layering of the material produces a 3D model. It has already been used for printing surgical models for preoperative planning and in constructing personalized prostheses for patients. The ultimate goal is to achieve the development of functional human organs and tissues, to overcome limitations of organ transplantation created by the lack of organ donors and life-long immunosuppression. We hypothesized a precision medicine approach to human organ fabrication using 3D printed technology, in which the digital volumetric data would be collected by imaging of a patient, i.e. CT or MRI images followed by mathematical modeling to create a digital 3D image. Then a suitable biocompatible material, with an optimal resolution for cells seeding and maintenance of cell viability during the printing process, would be printed with a compatible printer type and finally implanted into the patient. Life-saving operations with 3D printed implants were already performed in patients. However, several issues need to be addressed before translational application of 3D printing into clinical medicine. These are vascularization, innervation, and financial cost of 3D printing and safety of biomaterials used for the construct. Copyright © 2015 Elsevier Ltd. All rights reserved.

Novel Materials for 3D Printing by Photopolymerization.

Science.gov (United States)

Layani, Michael; Wang, Xiaofeng; Magdassi, Shlomo

2018-05-13

The field of 3D printing, also known as additive manufacturing (AM), is developing rapidly in both academic and industrial research environments. New materials and printing technologies, which enable rapid and multimaterial printing, have given rise to new applications and utilizations. However, the main bottleneck for achieving many more applications is the lack of materials with new physical properties. Here, some of the recent reports on novel materials in this field, such as ceramics, glass, shape-memory polymers, and electronics, are reviewed. Although new materials have been reported for all three main printing approaches-fused deposition modeling, binder jetting or laser sintering/melting, and photopolymerization-based approaches, apparently, most of the novel physicochemical properties are associated with materials printed by photopolymerization approaches. Furthermore, the high resolution that can be achieved using this type of 3D printing, together with the new properties, has resulted in new implementations such as microfluidic, biomedical devices, and soft robotics. Therefore, the focus here is on photopolymerization-based additive manufacturing including the recent development of new methods, novel monomers, and photoinitiators, which result in previously inaccessible applications such as complex ceramic structures, embedded electronics, and responsive 3D objects. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Photochemical Copper Coating on 3D Printed Thermoplastics

Science.gov (United States)

Yung, Winco K. C.; Sun, Bo; Huang, Junfeng; Jin, Yingdi; Meng, Zhengong; Choy, Hang Shan; Cai, Zhixiang; Li, Guijun; Ho, Cheuk Lam; Yang, Jinlong; Wong, Wai Yeung

2016-08-01

3D printing using thermoplastics has become very popular in recent years, however, it is challenging to provide a metal coating on 3D objects without using specialized and expensive tools. Herein, a novel acrylic paint containing malachite for coating on 3D printed objects is introduced, which can be transformed to copper via one-step laser treatment. The malachite containing pigment can be used as a commercial acrylic paint, which can be brushed onto 3D printed objects. The material properties and photochemical transformation processes have been comprehensively studied. The underlying physics of the photochemical synthesis of copper was characterized using density functional theory calculations. After laser treatment, the surface coating of the 3D printed objects was transformed to copper, which was experimentally characterized by XRD. 3D printed prototypes, including model of the Statue of Liberty covered with a copper surface coating and a robotic hand with copper interconnections, are demonstrated using this painting method. This composite material can provide a novel solution for coating metals on 3D printed objects. The photochemical reduction analysis indicates that the copper rust in malachite form can be remotely and photo-chemically reduced to pure copper with sufficient photon energy.

14 CFR 1245.109 - Assignment of title to NASA.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Assignment of title to NASA. 1245.109... INTELLECTUAL PROPERTY RIGHTS Patent Waiver Regulations § 1245.109 Assignment of title to NASA. (a) The instrument of waiver set forth in § 1245.115(c) shall be voided by NASA with respect to the domestic title to...

Three-Dimensional Printing in Zero Gravity

Science.gov (United States)

Werkheiser, Niki

2015-01-01

The 3D printing in zero-g (3D Print) technology demonstration project is a proof-of-concept test designed to assess the properties of melt deposition modeling additive manufacturing in the microgravity environment experienced on the International Space Station (ISS). This demonstration is the first step towards realizing a 'machine shop' in space, a critical enabling component of any deep space mission.

Characterizing Digital Light Processing (DLP) 3D Printed Primitives

DEFF Research Database (Denmark)

Tyge, Emil; Pallisgaard, Jens J.; Lillethorup, Morten

2015-01-01

The resolution and repeatability of 3D printing processes depends on a number of factors including the software, hardware, and material used. When printing parts with features that are near or below the nominal printing resolution, it is important to understand how the printer works. For example......, what is the smallest unit shape that can be produced? And what is the reproducibility of that process? This paper presents a method for automatically detecting and characterizing the height, width, and length of micro scale geometric primitives produced via a digital light processing (DLP) 3D printing...

A screen-printed flexible flow sensor

International Nuclear Information System (INIS)

Moschos, A; Kaltsas, G; Syrovy, T; Syrova, L

2017-01-01

A thermal flow sensor was printed on a flexible plastic substrate using exclusively screen-printing techniques. The presented device was implemented with custom made screen-printed thermistors, which allows simple, cost-efficient production on a variety of flexible substrates while maintaining the typical advantages of thermal flow sensors. Evaluation was performed for both static (zero flow) and dynamic conditions using a combination of electrical measurements and IR imaging techniques in order to determine important characteristics, such as temperature response, output repeatability, etc. The flow sensor was characterized utilizing the hot-wire and calorimetric principles of operation, while the preliminary results appear to be very promising, since the sensor was successfully evaluated and displayed adequate sensitivity in a relatively wide flow range. (paper)

A study of lip prints and its reliability as a forensic tool

Science.gov (United States)

Verma, Yogendra; Einstein, Arouquiaswamy; Gondhalekar, Rajesh; Verma, Anoop K.; George, Jiji; Chandra, Shaleen; Gupta, Shalini; Samadi, Fahad M.

2015-01-01

Introduction: Lip prints, like fingerprints, are unique to an individual and can be easily recorded. Therefore, we compared direct and indirect lip print patterns in males and females of different age groups, studied the inter- and intraobserver bias in recording the data, and observed any changes in the lip print patterns over a period of time, thereby, assessing the reliability of lip prints as a forensic tool. Materials and Methods: Fifty females and 50 males in the age group of 15 to 35 years were selected for the study. Lips with any deformity or scars were not included. Lip prints were registered by direct and indirect methods and transferred to a preformed registration sheet. Direct method of lip print registration was repeated after a six-month interval. All the recorded data were analyzed statistically. Results: The predominant patterns were vertical and branched. More females showed the branched pattern and males revealed an equal prevalence of vertical and reticular patterns. There was an interobserver agreement, which was 95%, and there was no change in the lip prints over time. Indirect registration of lip prints correlated with direct method prints. Conclusion: Lip prints can be used as a reliable forensic tool, considering the consistency of lip prints over time and the accurate correlation of indirect prints to direct prints. PMID:26668449

3D printed versus conventionally cured provisional crown and bridge dental materials.

Science.gov (United States)

Tahayeri, Anthony; Morgan, MaryCatherine; Fugolin, Ana P; Bompolaki, Despoina; Athirasala, Avathamsa; Pfeifer, Carmem S; Ferracane, Jack L; Bertassoni, Luiz E

2018-02-01

To optimize the 3D printing of a dental material for provisional crown and bridge restorations using a low-cost stereolithography 3D printer; and compare its mechanical properties against conventionally cured provisional dental materials. Samples were 3D printed (25×2×2mm) using a commercial printable resin (NextDent C&B Vertex Dental) in a FormLabs1+ stereolithography 3D printer. The printing accuracy of printed bars was determined by comparing the width, length and thickness of samples for different printer settings (printing orientation and resin color) versus the set dimensions of CAD designs. The degree of conversion of the resin was measured with FTIR, and both the elastic modulus and peak stress of 3D printed bars was determined using a 3-point being test for different printing layer thicknesses. The results were compared to those for two conventionally cured provisional materials (Integrity ® , Dentsply; and Jet ® , Lang Dental Inc.). Samples printed at 90° orientation and in a white resin color setting was chosen as the most optimal combination of printing parameters, due to the comparatively higher printing accuracy (up to 22% error), reproducibility and material usage. There was no direct correlation between printing layer thickness and elastic modulus or peak stress. 3D printed samples had comparable modulus to Jet ® , but significantly lower than Integrity ® . Peak stress for 3D printed samples was comparable to Integrity ® , and significantly higher than Jet ® . The degree of conversion of 3D printed samples also appeared higher than that of Integrity ® or Jet ® . Our results suggest that a 3D printable provisional restorative material allows for sufficient mechanical properties for intraoral use, despite the limited 3D printing accuracy of the printing system of choice. Copyright © 2017 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

3D concrete printing in architecture : a research on the potential benefits of 3D Printing in Architecture

NARCIS (Netherlands)

van der Zee, A.; Marijnissen, M.

2017-01-01

This research explores the use of large-scale 3D Printing techniques in architecture and structural design. First we will analyse the various methods in large-scale 3D printing in order to choose the method with the most potential to be used to build large-scale residential buildings in the

78 FR 22795 - EPAAR Clause for Printing

Science.gov (United States)

2013-04-17

... printing/duplication. ``Desktop Publishing'' is a method of composition using computers with the final... considered ``printing.'' However, if the output from desktop publishing is being sent to a typesetting device... preparing related illustrative material to a final document (camera-ready copy) using desktop publishing. (2...

3D Printing of Living Responsive Materials and Devices.

Science.gov (United States)

Liu, Xinyue; Yuk, Hyunwoo; Lin, Shaoting; Parada, German Alberto; Tang, Tzu-Chieh; Tham, Eléonore; de la Fuente-Nunez, Cesar; Lu, Timothy K; Zhao, Xuanhe

2018-01-01

3D printing has been intensively explored to fabricate customized structures of responsive materials including hydrogels, liquid-crystal elastomers, shape-memory polymers, and aqueous droplets. Herein, a new method and material system capable of 3D-printing hydrogel inks with programed bacterial cells as responsive components into large-scale (3 cm), high-resolution (30 μm) living materials, where the cells can communicate and process signals in a programmable manner, are reported. The design of 3D-printed living materials is guided by quantitative models that account for the responses of programed cells in printed microstructures of hydrogels. Novel living devices are further demonstrated, enabled by 3D printing of programed cells, including logic gates, spatiotemporally responsive patterning, and wearable devices. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Inheritance pattern of lip prints among Malay population: A pilot study.

Science.gov (United States)

George, Renjith; Nora Afandi, Nurulain Syafinaz Binti; Zainal Abidin, Siti Nur Hayati Binti; Binti Ishak, Nur Ismawani; Soe, Htoo Htoo Kyaw; Ismail, Abdul Rashid Hj

2016-04-01

We assessed the resemblance of lip print patterns between parents and biological offspring in families of 31 Malay students as well as the distribution of different types of lip print in the study group. Only a few studies have successfully established the inheritance pattern of lip prints. Such studies can be population specific and need to be conducted in various populations. No such study have been conducted in Malay population in Malaysia, according to our knowledge. Present study was carried out to ascertain whether there is any inherence pattern in lip prints and thereby to investigate the potential role of lip prints in personal identification. We found 58.06% resemblance of lip print patterns between the parents and their biological offspring in our study. The influence of heredity in lip print pattern is still a new concept and there is lack of concrete evidence. The data from our study shows that there is potential influence of inheritance in the lip print patterns among the family members. Further researches involving larger samples size are suggested to derive more reliable and accurate results. The most common lip print pattern among the study group is type I (29.84%) followed by type II (23.12%), type III (22.45%), type I' (13.44%), type IV (9.54%) and type V (1.61%). Racial variations in lip print patterns and their prevalence may serve as an aid in forensic identification and crime scene investigation. The results of this pilot study will help in establishing guidelines for future researches on lip print analysis in Malaysia. Lip print patterns are unique and individualistic. However, there are some similarities in basic patterns of lip prints between family members which may be attributed to influence of inheritance. 1. To determine the inheritance pattern of lip prints among Malay family members of the student. 2. To identify the distribution of different types of lip prints among Malay population. and Observational pilot study. Lip prints of 124

Browse Title Index

African Journals Online (AJOL)

Items 101 - 108 of 108 ... Issue, Title. Vol 8, No 2 (2016), The status and challenges of clinical informatics development in South Africa, Abstract PDF. Abayomi Kehinde Owolabi, Thokozani Patrick Mhlongo, Neil Evans. Vol 4, No 1 (2012), The stuttering implementation of language policies in the South African education system ...

Browse Title Index

African Journals Online (AJOL)

Items 751 - 800 of 846 ... Journal Home > Advanced Search > Browse Title Index ... Vol 9, No 3S (2017): Special Issue, The effect of torrefaction on oil palm ... core competency skills of IRBM tax auditors towards their performance, Abstract PDF ... of exchange rates behavior in Malaysia by using NATREX model, Abstract PDF.

Browse Title Index

African Journals Online (AJOL)

Items 51 - 76 of 76 ... Issue, Title. Vol 6, No 1 (2013), Integrating Sustainability into the Real Estate Valuation Process: A Nigerian Perspective, Abstract PDF. G K Babawale, B A Oyalowo. Vol 5, No 1 (2012), Internalising internationa valuation standards: Relevance and applicability issues in the Nigerian context, Abstract PDF.

Browse Title Index