WorldWideScience

Sample records for preparing hard copies

  1. Laser thermographic technologies for hard copy recording

    Science.gov (United States)

    Bessmel'tsev, Viktor P.; Baev, Sergej G.

    1995-04-01

    Methods of hard copies recording based on thermal interaction of the beam from CO2 or YAG lasers with various kinds of films on any substrates have been developed. The recording processes are single-step and require no additional development. Among them are: (1) Laser thermodestruction of thin mask layers or of a material surface on any kinds of substrates. (2) Laser thermochemical reactions of thermal decomposition of metal salts in solid state phase on a surface of various hygroscopic substrates. The laser recording devices using the methods, described above have been developed and are manufactured now; they allow one to record hard copies with a size of up to 27 X 31 inches, a resolution of 4000 dpi.

  2. Colour hard-copy from workstation screens

    Science.gov (United States)

    Clayton, C. A.

    It is possible to produce a colour print on the DEC LJ250 inkjet printer of either the entire screen or a portion of the screen from VAXstations, DECstations, SUN workstations and the IKON image display. This document describes how to achieve this with each of the above workstations. The IKONPAINT software which is used to produce colour hard-copy from the IKON screen on the inkjet printer is fully documented in SUN/71 and is not described here.

  3. 75 FR 4031 - Streamlining Hard-Copy Postage Statement Processing

    Science.gov (United States)

    2010-01-26

    ... From the Federal Register Online via the Government Publishing Office POSTAL SERVICE 39 CFR Part 111 Streamlining Hard-Copy Postage Statement Processing AGENCY: Postal Service\\TM\\. ACTION: Proposed rule. SUMMARY: The Postal Service\\TM\\ is proposing to revise Mailing Standards of the United States...

  4. IKONPAINT -- Ikon and GWM window to Inkjet Hard-copy

    Science.gov (United States)

    Page, Clive G.; Mellor, G. R.

    IKONPAINT provides ``push-button'' colour hard-copy from the Ikon screen or from a GWM window to an inkjet printer. The DEC Companion Colour Printer (LJ250/LJ252) and the Hewlett-Packard Paintjet are both supported. These printers normally take 8 by 11 inch fan-fold paper but single transparency sheets can be hand-fed.

  5. Hard Copy to Digital Transfer: 3D Models that Match 2D Maps

    Science.gov (United States)

    Kellie, Andrew C.

    2011-01-01

    This research describes technical drawing techniques applied in a project involving digitizing of existing hard copy subsurface mapping for the preparation of three dimensional graphic and mathematical models. The intent of this research was to identify work flows that would support the project, ensure the accuracy of the digital data obtained,…

  6. Hard Copy to Digital Transfer: 3D Models that Match 2D Maps

    Science.gov (United States)

    Kellie, Andrew C.

    2011-01-01

    This research describes technical drawing techniques applied in a project involving digitizing of existing hard copy subsurface mapping for the preparation of three dimensional graphic and mathematical models. The intent of this research was to identify work flows that would support the project, ensure the accuracy of the digital data obtained,…

  7. Comparison of medical students' learning approaches between electronic and hard copy team-based learning.

    Science.gov (United States)

    Sharaf, Fawzy; Alnohair, Sultan

    2017-01-01

    To compare the students' perception of team-based learning (TBL): The paper (hard copy) compared with the e-copy (electronic copy) in the family medicine course of the fifth year medical students, Qassim University College of Medicine. A cross-sectional study was conducted during the family medicine course in 2015-2016 to compare the hard copy and the e-copy TBL sessions. We used Google drive to distribute, collect and analyze the questionnaire. The results of the e-copy TBL are shown and displayed directly with each session to the students, which was not the same as practiced with hard copy. We used also SPSS (version 17 for Windows) for more statistical analysis. The total number of respondents of students in each was 96; a phase of TBL phase 1 (hard copy) and phase 2 (e-copy). Male were 64 (66.7%) and females 32 (33.3%). The first three knowledge questions showed no difference between the mean score between paper and e-copy TBL, but of the perception questions showed a significant difference between the paper and e-copy TBL. The results of the survey showed that the students prefer e-copy TBL as a course format, as it was an attraction for most of the students and making them even more successful in the key exam and e-copy TBL develop the skills needed to work productively in task-groups.

  8. A New method of preparing iso-hardness plots

    Science.gov (United States)

    Kumar, V.; Patwardhan, A. K.

    1993-02-01

    A new approach has been used for the preparation of iso-hardness plots, which are very useful in the heat treating of metals and alloys. An alloy white iron containing ~6% Mn, ~5% Cr, and ~3% Cu was heat treated at 800,850,900,950,1000, and 1050 °C and soaked for 2, 4, 6, 8, and 10 h, respectively, at each of these temperatures followed by air cooling. It was observed that, although the hardness varied linearly with soaking time, its variation with soaking temperature was nonlinear. This can be represented as: H = 98.285e2021.33/T + (0.037 - 0.316 × 10- 4 T) . t where H is Vickers hardness; T is soaking temperature in K; and t is soaking time in seconds. The variation in hardness has been discussed in light of microstructural changes that can take place upon heat treating. A three-dimensional plot of hardness, soaking temperature, and time was prepared based on the above equation. It revealed that the variation in hardness on heat treating can be represented as a surface instead of lines, where the change in the slope of the surface reflects the various transformations occurring in the alloy system. This iso- hardness plot, consisting of contours of constant hardness, has been prepared by projecting the above-mentioned surface on the soaking temperature- time plane. The method of selection of heat treating parameters based on this iso- hardness plot is discussed.

  9. Detection of masses and microcalcifications of breast cancer on digital mammograms: comparison among hard-copy film, 3-megapixel liquid crystal display (LCD) monitors and 5-megapixel LCD monitors: an observer performance study.

    Science.gov (United States)

    Kamitani, Takeshi; Yabuuchi, Hidetake; Soeda, Hiroyasu; Matsuo, Yoshio; Okafuji, Takashi; Sakai, Shuji; Furuya, Akio; Hatakenaka, Masamitsu; Ishii, Nobuhide; Honda, Hiroshi

    2007-05-01

    The purpose of the study was to compare observer performance in the detection of masses and microcalcifications of breast cancer among hard-copy reading and soft-copy readings using 3-megapixel (3M) and 5-megapixel (5M) liquid crystal display (LCD) monitors. For the microcalcification detection test, we prepared 100 mammograms: 40 surgically verified cancer cases and 60 normal cases. For the mass detection test, we prepared 100 mammograms: 50 cancer cases and 50 normal cases. After six readers assessed both microcalcifications and masses set for each modality, receiver operating characteristic (ROC) analysis was performed. The average A(z)s for mass detection using a hard copy and 3M and 5M LCD monitors were 0.923, 0.927 and 0.920, respectively; there were no significant differences. The average A(z) for microcalcification detection using hard copy, 3M and 5M LCD monitors was 0.977, 0.954 and 0.972, respectively. There were no significant differences, but the P-values between the hard copy and 3M LCD monitor and that between the 3M and 5M LCD monitor were 0.08 and 0.09, respectively. In conclusion, the observer performances for detecting masses of breast cancers were comparable among the hard copy and two LCD monitors; however, soft-copy reading with a 3M LCD monitor showed slightly lower observer performance for detecting microcalcifications of breast cancers than hard-copy or 5M LCD monitor reading.

  10. Computer Game Play as an Imaginary Stage for Reading: Implicit Spatial Effects of Computer Games Embedded in Hard Copy Books

    Science.gov (United States)

    Smith, Glenn Gordon

    2012-01-01

    This study compared books with embedded computer games (via pentop computers with microdot paper and audio feedback) with regular books with maps, in terms of fifth graders' comprehension and retention of spatial details from stories. One group read a story in hard copy with embedded computer games, the other group read it in regular book format…

  11. Computer Game Play as an Imaginary Stage for Reading: Implicit Spatial Effects of Computer Games Embedded in Hard Copy Books

    Science.gov (United States)

    Smith, Glenn Gordon

    2012-01-01

    This study compared books with embedded computer games (via pentop computers with microdot paper and audio feedback) with regular books with maps, in terms of fifth graders' comprehension and retention of spatial details from stories. One group read a story in hard copy with embedded computer games, the other group read it in regular book format…

  12. Single-image hard-copy display of the spine utilizing digital radiography

    Science.gov (United States)

    Artz, Dorothy S.; Janchar, Timothy; Milzman, David; Freedman, Matthew T.; Mun, Seong K.

    1997-04-01

    Regions of the entire spine contain a wide latitude of tissue densities within the imaged field of view presenting a problem for adequate radiological evaluation. With screen/film technology, the optimal technique for one area of the radiograph is sub-optimal for another area. Computed radiography (CR) with its inherent wide dynamic range, has been shown to be better than screen/film for lateral cervical spine imaging, but limitations are still present with standard image processing. By utilizing a dynamic range control (DRC) algorithm based on unsharp masking and signal transformation prior to gradation and frequency processing within the CR system, more vertebral bodies can be seen on a single hard copy display of the lateral cervical, thoracic, and thoracolumbar examinations. Examinations of the trauma cross-table lateral cervical spine, lateral thoracic spine, and lateral thoracolumbar spine were collected on live patient using photostimulable storage phosphor plates, the Fuji FCR 9000 reader, and the Fuji AC-3 computed radiography reader. Two images were produced from a single exposure; one with standard image processing and the second image with the standard process and the additional DRC algorithm. Both sets were printed from a Fuji LP 414 laser printer. Two different DRC algorithms were applied depending on which portion of the spine was not well visualized. One algorithm increased optical density and the second algorithm decreased optical density. The resultant image pairs were then reviewed by a panel of radiologists. Images produced with the additional DRC algorithm demonstrated improved visualization of previously 'under exposed' and 'over exposed' regions within the same image. Where lung field had previously obscured bony detail of the lateral thoracolumbar spine due to 'over exposure,' the image with the DRC applied to decrease the optical density allowed for easy visualization of the entire area of interest. For areas of the lateral cervical spine

  13. The gray-scale ink-jet printer: value in making hard copies of digital images.

    Science.gov (United States)

    Combs, M J; Snell, J; Cail, W S; Maier, T; Buck, D A

    1995-01-01

    Referring physicians often are supplied with copies of images to illustrate a report of the findings of a radiologic study or so that the radiologist can retain the original images. The increasing costs of production, film, and recovery of chemicals have enhanced the requirement for a clean, low-cost dry printing process. An ink-jet gray-scale paper printer (Unitone, Scitex Medical Systems, Bedford, MA) can print high-quality (300 dots per inch [dpi]) images with an effective 10-bit gray scale range by using the Hertz continuous ink-jet method [1-3], which does not require the use of a darkroom or hazardous chemicals. Several types of media (matte paper, glossy paper, transparency film) with a printing area of 26.9 x 43.7 cm (10.6 x 17.4 inches) may be used. The consumables are approximately 50-70% less expensive than the cost of silver halide film, providing a cost advantage over film for referral and archival copies. The results of an initial evaluation of the ink-jet printer at our institution are reported here.

  14. Diagnostic performance in differentiation of breast lesion on digital mammograms: comparison among hard-copy film, 3-megapixel LCD monitor, and 5-megapixel LCD monitor.

    Science.gov (United States)

    Kamitani, Takeshi; Yabuuchi, Hidetake; Matsuo, Yoshio; Setoguchi, Taro; Sakai, Shuji; Okafuji, Takashi; Sunami, Shunya; Hatakenaka, Masamitsu; Ishii, Nobuhide; Kubo, Makoto; Tokunaga, Eriko; Yamamoto, Hidetaka; Honda, Hiroshi

    2011-01-01

    We compared observer performance of digital mammography among hard-copy readings and soft-copy readings using 3-megapixel (3M) and 5-megapixel (5M) liquid crystal display (LCD) monitors. Five experienced radiologists assessed 80 mammograms of 40 cancers and 40 benign lesions. There were no significant differences among the average A(z) of three modalities and among the κ values for intra- and interobserver agreement. The soft-copy reading using the 3M LCD monitor took a slightly longer time, although there were no significant differences.

  15. Preparation of hard magnetic materials in thin film form

    Energy Technology Data Exchange (ETDEWEB)

    Pigazo, F.; Palomares, F.J. [Instituto de Ciencia de Materiales de Madrid-CSIC, c/ Sor Juana Ines de la Cruz 3, 28049 Madrid (Spain); Cebollada, F. [EUITT-UPM, Carretera de Valencia km 7, 28031 Madrid (Spain); Gonzalez, J.M. [Unidad Asociada ICMM-IMA, c/ Sor Juana Ines de la Cruz 3, 28049 Madrid (Spain)], E-mail: jesus.m.gonzalez@icmm.csic.es

    2008-07-15

    We report on the preparation, by means of pulsed laser ablation deposition, of trilayers of nominal composition Cr/SmCo{sub 5}/Cr//Si with thicknesses in the order of 250/240/125 nm, respectively. According to the results of the structural, chemical and magnetic characterizations performed in our as-deposited samples, the Sm-Co layer was structurally amorphous, exhibited abrupt compositional interfaces with the capping and buffering layers, and coercivities of a few hundreds of Oe. Magnetic hardness was developed upon submitting the samples to current anneals under vacuum at temperatures in the range of 540-670 deg. C. The hardening process was followed in detail by correlating the phase distribution, the nature of the interlayer atomic diffusion processes, the occurrence of textures and the temperature dependence of the coercive force. From our results we conclude about (i) the occurrence of a large degree of Co diffusion/segregation, which results in the detection, from the diffraction and magnetometric results, of the presence of CoCr alloys in the treated samples, and (ii) the close correlation, evidenced from the fits of the temperature dependence of the coercive force to the micromagnetic model, between the coercivity optimization and the crystallinity enhancement of the SmCo{sub 5} grains.

  16. Structure and hardness of a hard metal alloy prepared with a WC powder synthesized at low temperature

    Energy Technology Data Exchange (ETDEWEB)

    Costa, F.A. da [Programa de Pos-Graduacao em Ciencia e Engenharia de Materiais, UFRN, Campus Universitario, 59072-970 Natal, RN (Brazil)], E-mail: francineac@yahoo.com; Medeiros, F.F.P. de [Programa de Pos-Graduacao em Ciencia e Engenharia de Materiais, UFRN, Campus Universitario, 59072-970 Natal, RN (Brazil); Silva, A.G.P. da [Laboratorio de Materiais Avancados, UENF, 28015-620 Campos de Goytacazes, RJ (Brazil); Gomes, U.U. [Departamento de Fisica Teorica e Experimental, UFRN, Campus Universitario, 59072-970 Natal, RN (Brazil); Filgueira, M. [Laboratorio de Materiais Avancados, UENF, 28015-620 Campos de Goytacazes, RJ (Brazil); Souza, C.P. de [Laboratorio de Termodinamica e Reatores, UFRN, Campus Universitario, 59072-970 Natal, RN (Brazil)

    2008-06-25

    The structure and hardness of a WC-10 wt% Co alloy prepared with an experimental WC powder are compared with those of another alloy of the same composition produced under the same conditions and prepared with a commercial WC powder. The experimental WC powder was synthesized by a gas-solid reaction between APT and methane at low temperature and the commercial WC powder was conventionally produced by a solid-solid reaction between tungsten and carbon black. WC-10 wt% Co alloys with the two powders were prepared under the same conditions of milling and sintering. The structure of the sample prepared with the experimental WC powder is homogeneous and coarse grained. The structure of the sample prepared with the commercial powder is heterogeneous. Furthermore the size and shape of the WC grains are significantly different.

  17. TEMPO-oxidized Konjac glucomannan as appliance for the preparation of hard capsules

    NARCIS (Netherlands)

    Chen, Yuying; Zhao, Huiying; Liu, Xianwu; Li, Zusen; Liu, Bin; Wu, Jiande; Shi, Mengxuan; Norde, Willem; Li, Yuan

    2016-01-01

    TEMPO-oxidized Konjac glucomannan (OKGM) was developed as new material for preparing vegetarian hard capsules. OKGM of different degrees of oxidation: DO30%, DO50%, and DO80% were prepared to select optimum DO for capsule formation. FT-IR results proved that the primary alcohol groups on KGM were

  18. [Hard dental tissue minimal-invasive preparation using contemporary polymer rotating instruments and laser].

    Science.gov (United States)

    Beloica, Milos; Vulićević, Zoran R; Mandinić, Zoran; Radović, Ivana; Jovicić, Olivera; Carević, Momir; Tekić, Jasmina

    2014-01-01

    Goal of contemporary dentistry is to decrease the patient's discomfort during treatment. Dentists aim to achieve maximum with the newly developed dental materials as well as with new cavity preparation techniques in the shortest time span. Since the development of the first constructed borer (drilling machine) for caries removal, the preparation techniques have considerably changed. The progress of dental materials as well as the cavity preparation techniques has led us to contemporary carbide tungsten and diamond borers that are used with obligatory water cooling. The innovation within this field represents newly developed polymer borers that can detect the difference between carious lesions and healthy tooth structure. In this way the cavity preparation may be performed without damaging dental healthy tissue. This is possible owing to their hardness which is lower than the hardness of intact dentin. Polymer borer preparation is painless with less vibration, while the increase in temperature is negligible. Lasers have been used in clinical dentistry since 1980s so it can be said that they represent a new technology. The function of lasers is based on ablation which requires water. Erbium lasers have shown the highest potential with their ability to produce effective ablation of hard dental tissues. Laser application in dentistry requires special training as well as some protective measures. Laser advantages, compared to traditional preparation techniques, involve the absence of vibration, painless preparation, possibility of preparation without anesthetic and easier patient's adjustment to dental intervention which is of importance, especially in pediatric dentistry.

  19. Diagnostic performance of detecting breast cancer on computed radiographic (CR) mammograms: comparison of hard copy film, 3-megapixel liquid-crystal-display (LCD) monitor and 5-megapixel LCD monitor.

    Science.gov (United States)

    Yamada, Takayuki; Suzuki, Akihiko; Uchiyama, Nachiko; Ohuchi, Noriaki; Takahashi, Shoki

    2008-11-01

    The purpose was to compare observer performance in the detection of breast cancer using hard-copy film, and 3-megapixel (3-MP) and 5-megapixel (5-MP) liquid crystal display (LCD) monitors in a simulated screening setting. We amassed 100 sample sets, including 32 patients with surgically proven breast cancer (masses present, N = 12; microcalcifications, N = 10; other types, N = 10) and 68 normal controls. All the mammograms were obtained using computed radiography (CR; sampling pitch of 50 mum). Twelve mammographers independently assessed CR mammograms presented in random order for hard-copy and soft-copy reading at minimal 4-week intervals. Observers rated the images on seven-point (1 to 7) and continuous (0 to 100) malignancy scales. Receiver-operating-characteristics analysis was performed, and the average area under the curve (AUC) was calculated for each modality. The jackknife method with the Bonferroni correction was applied to multireader/multicase analysis. The average AUC values for the 3-MP LCD, 5-MP LCD, and hard-copy film were 0.954, 0.947, and 0.956 on the seven-point scale and 0.943, 0.923, and 0.944 on the continuous scale, respectively. There were no significant differences among the three modalities on either scale. Soft-copy reading using 3-MP and 5-MP LCDs is comparable to hard-copy reading for detecting breast cancer.

  20. Hard dental tissue minimal-invasive preparation using contemporary polymer rotating instruments and laser

    Directory of Open Access Journals (Sweden)

    Beloica Miloš

    2014-01-01

    Full Text Available Goal of contemporary dentistry is to decrease the patient’s discomfort during treatment. Dentists aim to achieve maximum with the newly developed dental materials as well as with new cavity preparation techniques in the shortest time span. Since the development of the first constructed borer (drilling machine for caries removal, the preparation techniques have considerably changed. The progress of dental materials as well as the cavity preparation techniques has led us to contemporary carbide tungsten and diamond borers that are used with obligatory water cooling. The innovation within this field represents newly developed polymer borers that can detect the difference between carious lesions and healthy tooth structure. In this way the cavity preparation may be performed without damaging dental healthy tissue. This is possible owing to their hardness which is lower than the hardness of intact dentin. Polymer borer preparation is painless with less vibration, while the increase in temperature is negligible. Lasers have been used in clinical dentistry since 1980s so it can be said that they represent a new technology. The function of lasers is based on ablation which requires water. Erbium lasers have shown the highest potential with their ability to produce effective ablation of hard dental tissues. Laser application in dentistry requires special training as well as some protective measures. Laser advantages, compared to traditional preparation techniques, involve the absence of vibration, painless preparation, possibility of preparation without anesthetic and easier patient’s adjustment to dental intervention which is of importance, especially in pediatric dentistry. [Projekat Ministarstva nauke Republike Srbije, br. 46009

  1. Preparation and Properties of High Hardness and Oxidation Resisting Coating Using Electric Arc Spray

    Institute of Scientific and Technical Information of China (English)

    LIZhuo-xin; CUILi; WANGJiang-ping; TANGChun-tian

    2004-01-01

    A coating with high hardness, wear and oxidation resistance was prepared by electric arc spray. The hardness, bonding strength, abrasive wear and values of porosity and oxidation resistance of the coating were investigated. The microstructures and function of Cr3C2 of the coating were analyzed. The results showed surface Rockness Hardness HR30 reached 72.5 and average bond strength reached 49.1Mpa. Also porosity value was less than 2%. In addition, it was found from the comparison between the coating and 45CT coating that, oxidation resistance of the coating was less than that of 45CT, but the abrasive wear of the coating was obvious better than that of 45CT.

  2. Preparation and Properties of High Hardness and Oxidation Resisting Coating Using Electric Arc Spray

    Institute of Scientific and Technical Information of China (English)

    LI Zhuo-xin; CUI Li; WANG Jiang-ping; TANG Chun-tian

    2004-01-01

    A coating with high hardness, wear and oxidation resistance was prepared by electric arc spray. The hardness,bonding strength, abrasive wear and values of porosity and oxidation resistance of the coating were investigated. The microstructures and function of Cr3C2 of the coating were analyzed. The results showed surface Rockness Hardness HR30 reached 72.5 and average bond strength reached 49.1Mpa. Also porosity value was less than 2%. In addition, it was found from the comparison between the coating and 45CT coating that, oxidation resistance of the coating was less than that of 45CT, but the abrasive wear of the coating was obvious better than that of 45CT.

  3. Preparation and investigation of ultrafine-grained tungsten carbide with high hardness and fracture toughness

    Science.gov (United States)

    Chuvil'deev, V. N.; Blagoveshchenskii, Yu. V.; Sakharov, N. V.; Boldin, M. S.; Nokhrin, A. V.; Isaeva, N. V.; Shotin, S. V.; Lopatin, Yu. G.; Smirnova, E. S.

    2015-07-01

    High-density samples of ultrafine-grained tungsten carbide with high hardness (up to 31-34 GPa) and increased fracture toughness (up to 5.2-6.4 MPa m1/2) are obtained using the technology of electropulse plasma sintering. The influence of the initial size of nanoparticles of α-WC prepared by plasmachemical synthesis on the density, structural parameters, and mechanical properties of tungsten carbide is investigated.

  4. Preparation of Hard Coating Films with High Refractive Index from Titania Nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Nam Woo; Ahn, Chi Yong; Song, Ki Chang [Konyang University, 121 Daehak-ro, Nonsan (Korea, Republic of)

    2015-12-15

    The titania (TiO{sub 2}) nanoparticles with a diameter 2-3 nm were synthesized by controlling hydrolysis of titanium tetraisopropoxide (TTIP) in acid solution. Organic-inorganic hybrid coating solutions were prepared by reacting the titania nanoparticles with 3-glycidoxypropyl trimethoxysilane (GPTMS) by the sol-gel method. The hard coating films with high refractive index were obtained by curing thermally at 120 .deg. C after spin-coating the coating solutions on the polycarbonate (PC) sheets. The coating films showed high optical transparency of 90% in the visible range and exhibited a pencil hardness of 2H. Also, the refractive index at 633 nm wavelength of coating films enhanced from 1.502 to 1.584 as the weight content of titania nanoparticles in the coating solutions increased from 4% to 25%.

  5. TEMPO-oxidized Konjac glucomannan as appliance for the preparation of hard capsules.

    Science.gov (United States)

    Chen, Yuying; Zhao, Huiying; Liu, Xianwu; Li, Zusen; Liu, Bin; Wu, Jiande; Shi, Mengxuan; Norde, Willem; Li, Yuan

    2016-06-05

    TEMPO-oxidized Konjac glucomannan (OKGM) was developed as new material for preparing vegetarian hard capsules. OKGM of different degrees of oxidation: DO30%, DO50%, and DO80% were prepared to select optimum DO for capsule formation. FT-IR results proved that the primary alcohol groups on KGM were oxidized into carboxyl groups. XRD analysis suggested that TEMPO-oxidation decreased the crystallinity of KGM. DO80% was considered as the optimum candidate for capsule preparation owing to its superior solubility, transparency and reduced viscosity. The hydrophilicity of OKGM films, measured by contact angle measurement, increased with increasing DO. The elongation at break and tensile strength of the OKGM films enhanced with increasing DO. In vitro drug dissolution profile of OKGM capsules showed that the shell rupture time of DO80% capsule is about 5-10 min, and 80% of the drugs were released within 30-45 min. Thus DO80% OKGM was qualified to be used for gastric soluble hard capsules. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Preparation of water-resistant antifog hard coatings on plastic substrate.

    Science.gov (United States)

    Chang, Chao-Ching; Huang, Feng-Hsi; Chang, Hsu-Hsien; Don, Trong-Ming; Chen, Ching-Chung; Cheng, Liao-Ping

    2012-12-11

    A novel water resistant antifog (AF) coating for plastic substrates was developed, which has a special hydrophilic/hydrophobic bilayer structure. The bottom layer, acting both as a mechanical support and a hydrophobic barrier against water penetration, is an organic-inorganic composite comprising colloidal silica embedded in a cross-linked network of dipentaethritol hexaacrylate (DPHA). Atop this layer, an AF coating is applied, which incorporates a superhydrophilic species synthesized from Tween-20 (surfactant), isophorone diisocyanate (coupling agent), and 2-hydroxyethyl methacrylate (monomer). Various methods, e.g., FTIR, SEM, AFM, contact angle, and steam test, were employed to characterize the prepared AF coatings. The results indicated that the size and the continuity of the hydrophilic domains on the top surface increased with increasing added amount of T20, however, at the expense of hardness, adhesiveness, and water resistivity. The optimal T20 content was found to be 10 wt %, at which capacity the resultant AF coating was transparent and wearable (5H, hardness) and could be soaked in water for 7 days at 25 °C without downgrading of its AF capability.

  7. Nazareth College: Specialty Preparation for Speech-Language Pathologists to Work with Children Who Are Deaf and Hard of Hearing

    Science.gov (United States)

    Brown, Paula M.; Quenin, Cathy

    2010-01-01

    The specialty preparation program within the speech-language pathology master's degree program at Nazareth College in Rochester, New York, was designed to train speech-language pathologists to work with children who are deaf and hard of hearing, ages 0 to 21. The program is offered in collaboration with the Rochester Institute of Technology,…

  8. Preparation and characterization of gelatin–hydroxyapatite composite microspheres for hard tissue repair

    Energy Technology Data Exchange (ETDEWEB)

    Chao, Shao Ching [Department of Materials Science and Engineering, National Chung Hsing University, 250 Kuo-Kuang Road, Taichung 40227, Taiwan (China); Department of Minimally Invasive Skull Neurosurgery, Neurological Institute, Taichung Veterans General Hospital, 1650 Taiwan Boulevard, Sect. 4, Taichung, Taiwan (China); Department of Neurosurgery, ChangHua Hospital, Ministry of Health and Welfare, 80 Chung Cheng Road, Sect. 2 Chiu Kuan Village, Changhua 500, Taiwan (China); Wang, Ming-Jia; Pai, Nai-Su [Department of Materials Science and Engineering, National Chung Hsing University, 250 Kuo-Kuang Road, Taichung 40227, Taiwan (China); Yen, Shiow-Kang, E-mail: skyen@dragon.nchu.edu.tw [Department of Materials Science and Engineering, National Chung Hsing University, 250 Kuo-Kuang Road, Taichung 40227, Taiwan (China)

    2015-12-01

    Gelatin–hydroxyapatite composite microspheres composed of 21% gelatin (G) and 79% hydroxyapatite (HA) with uniform morphology and controllable size were synthesized from a mixed solution of Ca(NO{sub 3}){sub 2}, NH{sub 4}H{sub 2}PO{sub 4} and gelatin by a wet-chemical method. Material analyses such as X-ray diffraction (XRD), scanning/transmission electron microscopy examination (SEM/TEM) and inductively coupled plasma-mass spectroscopy (ICP-MS) were used to characterize G–HA microspheres by analyzing their crystalline phase, microstructure, morphology and composition. HA crystals precipitate along G fibers to form nano-rods with diameters of 6–10 nm and tangle into porous microspheres after blending. The cell culture indicates that G–HA composite microspheres without any toxicity could enhance the proliferation and differentiation of osteoblast-like cells. In a rat calvarial defect model, G–HA bioactive scaffolds were compared with fibrin glue (F) and Osteoset® Bone Graft Substitute (OS) for their capacity of regenerating bone. Four weeks post-implantation, new bone, mineralization, and expanded blood vessel area were found in G–HA scaffolds, indicating greater osteoconductivity and bioactivity than F and OS. - Highlights: • G–HA composite microspheres were prepared by hydroxyapatite and gelatin. • In vitro tests indicated that the G–HA microspheres were biocompatible and bioactive. • In in vitro tests, G–HA microspheres could be applied in hard tissue engineering. • G–HA had healed the bone defect and provides a high proportion of surface area to open space.

  9. Preparation and Characterization of Biomimetic Hydroxyapatite-Resorbable Polymer Composites for Hard Tissue Repair

    Science.gov (United States)

    Hiebner, Kristopher Robert

    Autografts are the orthopedic "gold standard" for repairing bone voids. Autografts are osteoconductive and do not elicit an immune response, but they are in short supply and require a second surgery to harvest the bone graft. Allografts are currently the most common materials used for the repair of segmental defects in hard tissue. Unlike autografts, allografts can cause an undesirable immune response and the possibility of disease transmission is a major concern. As an alternative to the above approaches, recent research efforts have focused on the use of composite materials made from hydroxyapatite (HA) and bioresorbable polymers, such as poly-L-lactide (PLLA). Recent results have shown that the surface hydroxides on HA can initiate the ring opening polymerization (ROP) of L-lactide and other lactones creating a composite with superior interfacial strength. This thesis demonstrates that the surface of porous biologically derived HA substrates, such as coralline HA and trabecular bone, can be used to initiate the ROP of L-lactide and other lactones from the vapor phase. This process increases the strength of the porous scaffold through the deposition of a thin, uniform polymer coating, while maintaining the porous structure. The kinetics of the chemical vapor deposition polymerization (CVDP) are described using a quartz crystal microbalance (QCM). The reaction temperature and monomer vapor pressure are found to affect the rate of the polymerization. Also described in this thesis is the preparation of a porous polymer scaffold that mimics the structure of demineralized bone matrix (DBM). This demineralized bone matrix simulant (DBMS) is created using anorganic bovine bone as a template to initiate the polymerization of various lactones, followed by the removal of the HA scaffold. This material retained its shape and exhibits mechanical properties superior to DBM. Finally it is shown that HA can be used to initiate the ROP of a-caprolactam and the biocompatibility

  10. High Purity Tungsten Spherical Particle Preparation From WC-Co Spent Hard Scrap

    Directory of Open Access Journals (Sweden)

    Han Chulwoong

    2015-06-01

    Full Text Available Tungsten carbide-cobalt hard metal scrap was recycled to obtain high purity spherical tungsten powder by a combined hydrometallurgy and physical metallurgy pathway. Selective leaching of tungsten element from hard metal scrap occurs at solid / liquid interface and therefore enlargement of effective surface area is advantageous. Linear oxidation behavior of Tungsten carbide-cobalt and the oxidized scrap is friable to be pulverized by milling process. In this regard, isothermally oxidized Tungsten carbide-cobalt hard metal scrap was mechanically broken into particles and then tungsten trioxide particle was recovered by hydrometallurgical method. Recovered tungsten trioxide was reduced to tungsten particle in a hydrogen environment. After that, tungsten particle was melted and solidified to make a spherical one by RF (Ratio Frequency thermal plasma process. Well spherical tungsten micro-particle was successfully obtained from spent scrap. In addition to the morphological change, thermal plasma process showed an advantage for the purification of feedstock particle.

  11. Comparison of linear dimensional change, surface hardness and surface roughness of refractory model prepared from two different duplicating media.

    Science.gov (United States)

    Porwal, Amit; Chandrashekhar, Naveen H; Nadiger, Ramesh K; Meshramkar, Roseline D; Guttal, Satyabodh S

    2011-03-01

    The aim of this study was to evaluate and compare the linear dimensional change, surface hardness and surface roughness of the refractory casts poured against different duplicating media. Polyvinyl siloxane and Agar-agar were used for duplicating the stainless steel die. Sixty refractory models were prepared which were divided into two groups: I and II with 30 samples each respectively. Each group was subdivided into 3 subgroups with 10 samples each which were treated differently. All the specimens were measured for the linear dimensional change and surface hardness and the obtained data was statistically analyzed. Surface roughness was evaluated qualitatively taking SEM photomicrographs. Statistical analysis of linear dimensional change using one-way ANOVA showed statistically significant difference between subgroups of group I and non-significant difference between subgroups of group II. One-way ANOVA for Brinell hardness number showed statistically significant difference between the subgroups of group I & II. Student's 't' test results for linear dimensional change among different subgroups of group I & II showed significant difference between IA-IIA, IB-IIB, IC-IIC. Similarly 't'-test results for Brinell hardness number showed significant difference between subgroups IA-IIA, IB-IIB, and IC-IIC. Surface characteristics of the refractory casts poured against polyvinyl siloxane duplicating media were found to be better than the Agar media.

  12. Mesoporous carbon prepared from carbohydrate as hard template for hierarchical zeolites

    DEFF Research Database (Denmark)

    Egeblad, Kresten; Christensen, Claus H.

    2007-01-01

    treatment of a mixture of sucrose and ammonia followed by carbonization of the mixture in N-2 at high temperatures. The porous carbon produced by this method was subsequently applied as a hard template in the synthesis of mesoporous silicalite-1 and removed by combustion after synthesis. X-ray diffraction...

  13. Complementary analysis of the hard and soft protein corona: sample preparation critically effects corona composition

    Science.gov (United States)

    Winzen, S.; Schoettler, S.; Baier, G.; Rosenauer, C.; Mailaender, V.; Landfester, K.; Mohr, K.

    2015-02-01

    Here we demonstrate how a complementary analysis of nanocapsule-protein interactions with and without application media allows gaining insights into the so called hard and soft protein corona. We have investigated how both human plasma and individual proteins (human serum albumin (HSA), apolipoprotein A-I (ApoA-I)) adsorb and interact with hydroxyethyl starch (HES) nanocapsules possessing different functionalities. To analyse the hard protein corona we used sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE) and a protein quantitation assay. No significant differences were observed with regards to the hard protein corona. For analysis of the soft protein corona we characterized the nanocapsule-protein interaction with isothermal titration calorimetry (ITC) and dynamic light scattering (DLS). DLS and ITC measurements revealed that a high amount of plasma proteins were adsorbed onto the capsules' surface. Although HSA was not detected in the hard protein corona, ITC measurements indicated the adsorption of an HSA amount similar to plasma with a low binding affinity and reaction heat. In contrast, only small amounts of ApoA-I protein adsorb to the capsules with high binding affinities. Through a comparison of these methods we have identified ApoA-I to be a component of the hard protein corona and HSA as a component of the soft corona. We demonstrate a pronounced difference in the protein corona observed depending on the type of characterization technique applied. As the biological identity of a particle is given by the protein corona it is crucial to use complementary characterization techniques to analyse different aspects of the protein corona.Here we demonstrate how a complementary analysis of nanocapsule-protein interactions with and without application media allows gaining insights into the so called hard and soft protein corona. We have investigated how both human plasma and individual proteins (human serum albumin (HSA), apolipoprotein A

  14. Complementary analysis of the hard and soft protein corona: sample preparation critically effects corona composition.

    Science.gov (United States)

    Winzen, S; Schoettler, S; Baier, G; Rosenauer, C; Mailaender, V; Landfester, K; Mohr, K

    2015-02-21

    Here we demonstrate how a complementary analysis of nanocapsule-protein interactions with and without application media allows gaining insights into the so called hard and soft protein corona. We have investigated how both human plasma and individual proteins (human serum albumin (HSA), apolipoprotein A-I (ApoA-I)) adsorb and interact with hydroxyethyl starch (HES) nanocapsules possessing different functionalities. To analyse the hard protein corona we used sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE) and a protein quantitation assay. No significant differences were observed with regards to the hard protein corona. For analysis of the soft protein corona we characterized the nanocapsule-protein interaction with isothermal titration calorimetry (ITC) and dynamic light scattering (DLS). DLS and ITC measurements revealed that a high amount of plasma proteins were adsorbed onto the capsules' surface. Although HSA was not detected in the hard protein corona, ITC measurements indicated the adsorption of an HSA amount similar to plasma with a low binding affinity and reaction heat. In contrast, only small amounts of ApoA-I protein adsorb to the capsules with high binding affinities. Through a comparison of these methods we have identified ApoA-I to be a component of the hard protein corona and HSA as a component of the soft corona. We demonstrate a pronounced difference in the protein corona observed depending on the type of characterization technique applied. As the biological identity of a particle is given by the protein corona it is crucial to use complementary characterization techniques to analyse different aspects of the protein corona.

  15. Effect of annealing on microstructure, grain growth, and hardness of nanocrystalline Fe-Ni alloys prepared by mechanical alloying

    Energy Technology Data Exchange (ETDEWEB)

    Kotan, H., E-mail: hkotan@ncsu.edu [Department of Materials Science and Engineering, NC State University, 911 Partners Way, Room 3078, Raleigh, NC 27606-7907 (United States); Saber, M.; Koch, C.C.; Scattergood, R.O. [Department of Materials Science and Engineering, NC State University, 911 Partners Way, Room 3078, Raleigh, NC 27606-7907 (United States)

    2012-08-30

    Highlights: Black-Right-Pointing-Pointer Iron-nickel powders were hardened to 9.5 GPa by the mechanism of grain refinement strengthening using ball-milling. Black-Right-Pointing-Pointer We annealed the prepared powders and observed reduced hardness and extensive grain growth above 500 Degree-Sign C. Black-Right-Pointing-Pointer The Vickers hardness as a function of the grain size was found to exhibit a Hall-Petch slope. Black-Right-Pointing-Pointer Retained austenite was observed for Fe-8Ni and Fe-10Ni alloys annealed in the two-phase region. Black-Right-Pointing-Pointer As-milled microstructure plays an important role on the formation of austenite in the two-phase region. - Abstract: Fe-xNi alloys from x = 0 to x = 15 with an as-milled grain size and hardness in the range of 8-11 nm and 8.5-9.5 GPa, respectively, were synthesized by ball milling. Microstructural changes, hardness, and grain growth due to annealing were characterized using X-ray diffractometry, microhardness, focused ion beam channeling contrast imaging, and optical microscopy. It was found that the composition range of single bcc phase was extended by ball milling. Subsequent annealing of MA samples resulted in reduction of hardness and extensive grain growth. It indicates that nickel has no significant effect on thermal stabilization of iron. Retained austenite was observed for Fe-8Ni and Fe-10Ni alloys annealed in the two-phase region and effect of as-milled structure on retained austenite formation was discussed.

  16. Hard dental tissue minimal-invasive preparation using contemporary polymer rotating instruments and laser

    OpenAIRE

    Beloica Miloš; Vulićević Zoran R.; Mandinić Zoran; Radović Ivana; Jovičić Olivera; Carević Momir; Tekić Jasmina

    2014-01-01

    Goal of contemporary dentistry is to decrease the patient’s discomfort during treatment. Dentists aim to achieve maximum with the newly developed dental materials as well as with new cavity preparation techniques in the shortest time span. Since the development of the first constructed borer (drilling machine) for caries removal, the preparation techniques have considerably changed. The progress of dental materials as well as the cavity preparation techniqu...

  17. Original Copies

    DEFF Research Database (Denmark)

    Sørensen, Tim Flohr

    2013-01-01

    of similarity by looking at artefactual similarity as the results of prototyping and as a production of simulacra. In this light, the concept of copying turns out to be more than simply a matter of trying to imitate an exotic or prestigious original, and it fundamentally raises the question how different a copy...

  18. Methodological conception for the preparation of teachers who teach to deaf and hard hearing persons in the local historical contents.

    Directory of Open Access Journals (Sweden)

    Zeida María Montano Rivero

    2013-09-01

    Full Text Available The present work has as an objective: to apply a theoretical-methodological conception for the teacher's preparation in imparting the local historical contents, from an integrative approach in the development of the educational process in the special school for deaf and hard hearing in the Province of Sancti Spiritus, It is designed from the theoretical and methodological mistakes detected in the pedagogical practice. The sample is composed by the 12 teachers that represent 100% of the second cycle; It was used the technical investigative process as: interviews to teachers and observations to classes, which evidenced weaknesses in the theoretical preparation - methodological to carry out the development of these contents. The workshops were applied in the methodological preparation of the cycle community, in the space established by the Direction of the Ministry of Education, twice in every month and during the self preparation by teachers. The practical contribution is concrete in the determination of demands and didactic procedures for the use of the local historical contents with an integrative focus that constitutes the theoretical component of the conception, allowing the improvement of the preparation, in a significant way and in this way to contribute to an integral attention of the educational process.

  19. Incomparable hardness and modulus of biomimetic porous polyurethane films prepared by directional melt crystallization of a solvent

    Science.gov (United States)

    An, Suyeong; Kim, Byoungsoo; Lee, Jonghwi

    2017-07-01

    Porous materials with surprisingly diverse structures have been utilized in nature for many functional purposes. However, the structures and applications of porous man-made polymer materials have been limited by the use of processing techniques involving foaming agents. Herein, we demonstrate for the first time the outstanding hardness and modulus properties of an elastomer that originate from the novel processing approach applied. Polyurethane films of 100-μm thickness with biomimetic ordered porous structures were prepared using directional melt crystallization of a solvent and exhibited hardness and modulus values that were 6.8 and 4.3 times higher than those of the random pore structure, respectively. These values surpass the theoretical prediction of the typical model for porous materials, which works reasonably well for random pores but not for directional pores. Both the ordered and random pore structures exhibited similar porosities and pore sizes, which decreased with increasing solution concentration. This unexpectedly significant improvement of the hardness and modulus could open up new application areas for porous polymeric materials using this relatively novel processing technique.

  20. SEM evaluation of the morphological changes in hard dental tissues prepared by Er: YAG laser and rotary instruments

    Directory of Open Access Journals (Sweden)

    Tomov Georgi

    2010-09-01

    Full Text Available Effective ablation of dental hard tissues by means of the erbium:yttrium-aluminum garnet (Er: YAG laser has been reported recently, and its application to caries removal and cavity preparation has been expected. However, few studies have investigated the morphological changes in hard dental tissues after Er: YAG laser caries treatment. In the present study the morphological changes in hard dental tissues after Er: YAG laser caries ablation in vitro was compared with that of conventional mechanical treatment. Thirty extracted human teeth with caries were used. Ten tooth was treated with the Er: YAG laser, and the other was treated with a conventional steel and diamond burs. Laser treatment was performed by means of a non-contact irradiation modes with cooling water spray, with a new Er: YAG laser (LiteTouch. Conventional bur treatment was conducted by means of a low-speed micromotor and air turbine with water cooling. Scanning electron microscope (SEM observations were performed for each treatment. The Er: YAG laser ablated carious dentin effectively with minimal thermal damage to the surrounding intact dentin, and removed infected and softened carious dentin to the same degree as the burtreatment. In addition, a lower degree of vibration was noted with the Er: YAG laser treatment. The SEM examination revealed characteristic micro-irregularities of the lased dentin and enamel surfaces with potential benefits for adhesive restorations. Our results show that the Er: YAG laser is promising as a new technical modality for caries treatment

  1. Structure property relationships of nitride superlattice hard coatings prepared by pulsed laser deposition

    Science.gov (United States)

    Patel, Nitin

    Today, more than 40% of all cutting tools used in machining applications are covered with coatings. Coatings improve wear resistance, increase tool life, enable use at higher speed, and broaden the application range. Superlattices, where thin layers (typically deposited in an alternating fashion, are widely used commercially. Importantly, the hardness value of a superlattice (e.g. TiN/AlN) can significantly exceed the rule of mixture value. Superlattice coatings built from crystallographically dissimilar materials are not widely studied but hold promise for improvements in performance by allowing for both hardness and toughness to be simultaneously optimized. This is what this thesis is concerned with: a structure-property comparison of isostructural superlattices with corresponding non-isostructural superlattices. In order to grow both isostructural and non-isostructural superlattices from the same set of materials, it is necessary to grow monolithic films in different phases. Towards this end, the synthesis of different phases of AlN, (Ti,Al)N, TaN, and TiN was investigated. Films were grown by pulsed laser deposition in two different chambers that had different base pressures to study the effect of background gases on the phases and orientations of the films. Growth of AlN and (Ti,Al)N films is strongly affected in a chamber that had a base pressure of 10-6 Torr, but the films adopt their stable nitride structures in a chamber with the lower base pressure of 10-8 Torr. TaN adopts either the cubic rock salt structure or its stable hexagonal structure, depending on the growth temperature, while TiN grows as rock salt in all conditions. Single crystal epitaxial superlattices were then grown with different compositions, periodicities, and crystallographic orientations to compare the effect of chemistry, nanostructure, and crystallographic texture on hardness. Finally, the structure-property relationships of non-isostructural (cubic/hexagonal) superlattices are

  2. Hard and relaxed a-SiNxHy films prepared by PECVD: Structure analysis and formation mechanism

    Science.gov (United States)

    Xu, Xiangdong; He, Qiong; Fan, Taijun; Jiang, Yadong; Huang, Long; Ao, Tianhong; Ma, Chunqian

    2013-01-01

    Amorphous hydrogenated silicon nitride (a-SiNxHy) films were prepared by plasma-enhanced chemical vapor deposition (PECVD). Their chemical structures and mechanical properties were investigated. Results reveal that there are four kinds of Sisbnd N groups, involving Si3N4, Hsbnd Sisbnd N3, H2sbnd Sisbnd N2, and Si3sbnd Sisbnd N, in the a-SiNxHy films. Deposition at 300 °C and flow ratio of SiH4/NH3 = 30/30 sccm leads to the yield of special a-SiNxHy films, in which per two high-N-coordinated Sisbnd N groups (Si3N4 or Hsbnd Sisbnd N3) are distributed with one inter-buffer group (Si3sbnd Sisbnd N). Such a-SiNxHy films exhibit ultralow residual stress (-0.17 MPa), high elastic modulus (206.9 GPa) and high uniformity, holding great potential for device fabrications. The chemical reactions for the formation of a-SiNxHy films were proposed, and the thermodynamic calculations indicate that the utilization ratio of NH3 reagent in the chemical reactions increases significantly with the increase of SiH4 flow, but the utilization ratio of Sisbnd N bonds in the a-SiNxHy formation decreases inversely. This work discloses valuable information on the chemical reactions and structures for a-SiNxHy films, and suggests a route to the preparation of a-SiNxHy films with high hardness and low stress by conventional PECVD.

  3. Morphological changes in hard dental tissues prepared by Er:YAG laser (LiteTouch, Syneron), Carisolv and rotary instruments. A scanning electron microscopy evaluation.

    Science.gov (United States)

    Tsanova, Snejana Ts; Tomov, Georgi T

    2010-01-01

    This in vitro investigation aimed to study by means of scanning electron microscope the morphological changes in hard dental tissues after using several different methods for caries removal and cavity preparation. Twenty freshly extracted human teeth with carious lesions were used in the study. They were assigned to four groups depending on the method used for preparation: Group 1--Cavity preparation using Er: YAG laser (LiteTouch, Syneron, Israel). Group 2--Chemomechanical preparation using colourless Carisolv gel (MediTeam AB, Savedalen, Sweden). Group 3--Mechanical rotary preparation using diamond burs and air turbine. Group 4--Mechanical rotary preparation using by steel burs and micromotor. The preparations were performed strictly according to the manufacturer's instructions for proper use of instruments. The teeth samples were prepared for histological study and investigated by a scanning electron microscope at different magnification; the morphological changes in the tissues were registered and compared. There were considerable differences in the surface characteristics of the dental tissues when we analysed the photomicrographs of the specimens obtained using scanning electron microscopy (SEM). The surface after laser treatment remained highly retentive with no residual smear layer; the second best results in this respect were registered when teeth were chemomechanically excavated with Carisolv gel. The mechanical methods of cavity preparation resulted in surfaces with a smear layer of dentin without any microretentions. The scanning electron microscopy of hard dental tissues prepared using steel and diamond burs showed surfaces covered with a thick smear layer that may be relevant to the subsequent bonding of adhesive restorative materials to the prepared cavity. In preparing the surface using a turbine with diamond burs the smear layer was thinner and part of the dentinal tubules orifices were open in the area of water turbulence. SEM analysis of hard

  4. Novel hard materials with controlled (W0.5Al0.5)C grain shapes: in-situ high pressure preparation and mechanical properties

    Institute of Scientific and Technical Information of China (English)

    Zhuhui QIAO; Xianfeng MA; Huaguo TANG; Wei ZHAO; Jianwei LIU

    2012-01-01

    A novel hard material with various (W0.5Al0.5)C grain shapes was successfully prepared through mechanical alloying and in-situ high-pressure sintering process.X-ray diffraction apparatus and scanning electron microscopy were used to characterize the phase and the microstructures of the samples.The novel hard materials with “fibrous”,“rounded” and “plate-like” grains,which do not contain sharp edges,have the improved mechanical properties.The bulk boundless (W0.5Al0.5)C hard material with various (W0.5Al0.5)C grain shapes possesses good mechanical properties and light weight.The formation mechanism for the non-equilibrium (W0.5Al0.5)C grains during in-situ high-pressure sintering is also discussed.

  5. A Comparative Study on Micro Hardness and Structural Changes of Dentin Floor Cavity Prepared by Er: YAG Laser Irradiation and Mechanical Bur

    Directory of Open Access Journals (Sweden)

    Arbabzadeh F.

    2013-06-01

    Full Text Available Statement of Problem: Laser irradiation makes structural and chemical changes on the dental hard tissues. These changes alter the level of solubility and permeability of dentin. Purpose: The aim of this study was to compare the microhardness and the structural changes in the dentin cavity floor prepared with Er: YAG laser and bur.Material and Methods: In this experimental study, fifteen intact human molars were selected. Two square cavities were prepared on the buccal and lingual surfaces of each tooth. One side was randomly prepared by Er:YAG laser and the other side by bur. The specimens were divided into two halves. Consequently, there were 30 samples in every group. One half was assigned for the Vickers’s hardness test and the other one, for determination of Ca and P percentage and atomic elements analysis. The data were analyzed by Paired T-tests through SPSS16 (α≤o.o5.Results: The means and the standard deviation of the microhardness were 69.77±25.62 and 51.33±9.31 Kg/mm2 in the laser and bur groups, respectively. Statistical analysis showed significant differences between the two groups (p=0.017. Weight percentage of calcium in the laser cavity (65.5 was less than the bur cavities (68.21 and the difference was significant (p= 0.037.Conclusion: The hardness of dentin in laser group was higher than the bur group because of the higher mineral content of the dentin. The hardness and the mineral content of dentin are important factors in the bonding effectiveness of the dental materials so with laser cavity preparation, good mineral substrate are available for a better bonding.

  6. Hard electronics; Hard electronics

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Hard material technologies were surveyed to establish the hard electronic technology which offers superior characteristics under hard operational or environmental conditions as compared with conventional Si devices. The following technologies were separately surveyed: (1) The device and integration technologies of wide gap hard semiconductors such as SiC, diamond and nitride, (2) The technology of hard semiconductor devices for vacuum micro- electronics technology, and (3) The technology of hard new material devices for oxides. The formation technology of oxide thin films made remarkable progress after discovery of oxide superconductor materials, resulting in development of an atomic layer growth method and mist deposition method. This leading research is expected to solve such issues difficult to be easily realized by current Si technology as high-power, high-frequency and low-loss devices in power electronics, high temperature-proof and radiation-proof devices in ultimate electronics, and high-speed and dense- integrated devices in information electronics. 432 refs., 136 figs., 15 tabs.

  7. Scaling up Copy Detection

    OpenAIRE

    Li, Xian; Dong, Xin Luna; Lyons, Kenneth B.; Meng, Weiyi; Srivastava, Divesh

    2015-01-01

    Recent research shows that copying is prevalent for Deep-Web data and considering copying can significantly improve truth finding from conflicting values. However, existing copy detection techniques do not scale for large sizes and numbers of data sources, so truth finding can be slowed down by one to two orders of magnitude compared with the corresponding techniques that do not consider copying. In this paper, we study {\\em how to improve scalability of copy detection on structured data}. Ou...

  8. Hard electronics; Hard electronics

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In the fields of power conversion devices and broadcasting/communication amplifiers, high power, high frequency and low losses are desirable. Further, for electronic elements in aerospace/aeronautical/geothermal surveys, etc., heat resistance to 500degC is required. Devices which respond to such hard specifications are called hard electronic devices. However, with Si which is at the core of the present electronics, the specifications cannot fully be fulfilled because of the restrictions arising from physical values. Accordingly, taking up new device materials/structures necessary to construct hard electronics, technologies to develop these to a level of IC were examined and studied. They are a technology to make devices/IC of new semiconductors such as SiC, diamond, etc. which can handle higher temperature, higher power and higher frequency than Si and also is possible of reducing losses, a technology to make devices of hard semiconducter materials such as a vacuum microelectronics technology using ultra-micro/high-luminance electronic emitter using negative electron affinity which diamond, etc. have, a technology to make devices of oxides which have various electric properties, etc. 321 refs., 194 figs., 8 tabs.

  9. Why Can We Copy Classical Information?

    Institute of Scientific and Technical Information of China (English)

    SHEN Yao; HAO Liang; LONG Gui-Lu

    2011-01-01

    It is pointed out that the noncloning theorem in quantum mechanics also holds for unknown state in linear classical physics. The apparent capability of copying of a classical state is essentially the capability of perfect measurement in classical physics. The difference in copying between quantum and classical physics is the difference in measurement between the two theories. A classical copying process is the combined action of measurement of an unknown state and the preparation of this state onto another system. Hence perfect measurability in classical physics enables the copying of a classical state.

  10. Morphological Study Of Border Area Of Pulp-Capping Materials And Er:YAG Laser Prepared Hard Dental Surface.

    Science.gov (United States)

    Stefanova, Vessela P; Tomov, Georgi T; Tsanova, Snezhana Ts

    2015-01-01

    Vital pulp therapy involves biologically based therapeutic activities aimed at restoring health and preserving the vitality of cariously or traumatically damaged pulp. Adaptation of pulp-capping materials to the prepared tooth surface may be the key to the success of biological tooth treatment. To investigate the area of adaptation of synthetic tricalcium silicate cement, calcium hydroxide cement and mineral trioxide-aggregate to the dentin surface, prepared with the help of Er:YAG dental laser. Four extracted human tooth cavities were prepared with the help of Er:YAG dental laser (LiteTouch, Syneron, Israel), establishing microcommunication with the pulp chamber less than 1 mm in diameter. As pulp-capping materials in the cavities we used tricalcium silicate cement (Biodentine, Septodont, France), calcium hydroxide cement (Dycal) and mineral-trioxide aggregate (ProRoot MTA), stirred and administered according to manufacturers' instructions. The first material fills the whole cavity and the other two are spread in a thin layer and sealed with glass ionomer cement. Thus prepared, the samples were left for three days at 37°C in humidified environment. The samples were prepared for scanning electron microscopy (SEM) by standard methodology. The border area surfaces of the materials and the dentin were scanned using electron microscopy. The morphological changes occurring to the Er:YAG laser prepared dentin and the structural characteristics of the studied pulp-capping materials are demonstrated using scanograms. The border areas where good contact of materials and dentinal tubules is established are thoroughly studied. Good adaptation is seen in three-calcium silicate cement, followed by mineral trioxide aggregate and calcium hydroxide cement. The dentin surface, prepared with Er:YAG laser demonstrates a very good adaptation of the three tested pulp-capping materials.

  11. Ketoprofen mesoporous silica nanoparticles SBA-15 hard gelatin capsules: preparation and in vitro/in vivo characterization.

    Science.gov (United States)

    Abd-Elrahman, Ahmed A; El Nabarawi, Mohamed A; Hassan, Doaa H; Taha, Amal A

    2016-11-01

    SBA-15 is used to enhance the bioavailability of poorly soluble ketoprofen (KP) through stabilization of its amorphous state. Additionally, the current work provides a complete in vitro and in vivo study on preformulated KP-SBA-15 sample and formulated KP-SBA-15 in hard gelatin capsule. Loading of KP was done by a novel method called immersion-rotavapor method. KP was quantified by extraction and thermal gravimetric analysis (TGA). Characterization of the loaded SBA-15 sample was done by high resolution transmission electron microscopy (HRTEM), small angle X-ray diffraction (SAXRD), nitrogen adsorption/desorption isotherms, differential scanning calorimetry (DSC), Fourier transform infrared (FT-IR) spectroscopy and dissolution profiles. The loaded sample was formulated in hard gelatin capsule. The anti-inflammatory and analgesic studies were carried out on 24 adult male albino rats. TGA and extraction results showed 54.4 wt% of drug incorporated. Characterization of KP-SBA-15 sample confirmed the successful encapsulation of KP into the carrier pores in a molecular amorphous state. Additionally, loading of KP did not affect the mesoporous internal structure. During the first 5 min, the dissolution study showed very high release rates; nearly 50% of KP was released. These results were reflected on the in vivo study resulting in 82% inhibition in edema after 1 h and maximum analgesia after 30 min from the administration of the formulated sample. SBA-15 mesoporous silica nanoparticle proved to be a very promising drug delivery carrier that can be used as a facile way to enhance the bioavailability of poorly soluble drugs.

  12. Morphological Study Of Border Area Of Pulp-Capping Materials And Er:YAG Laser Prepared Hard Dental Surface

    Directory of Open Access Journals (Sweden)

    Stefanova Vessela P.

    2015-03-01

    Full Text Available Introduction: Vital pulp therapy involves biologically based therapeutic activities aimed at restoring health and preserving the vitality of cariously or traumatically damaged pulp. Adaptation of pulp-capping materials to the prepared tooth surface may be the key to the success of biological tooth treatment.

  13. Quantum copying: A review

    Directory of Open Access Journals (Sweden)

    Mark Hillery

    2000-07-01

    Full Text Available Quantum information is stored in two-level quantum systems known as qubits. The no-cloning theorem states that the state of an unknown qubit cannot be copied. This is in contrast to classical information which can be copied. If one drops the requirement that the copies be perfect it is possible to design quantum copiers. This paper presents a short review of the theory of quantum copying.

  14. Faculty needs, doctoral preparation, and the future of teacher preparation programs in the education of deaf and hard of hearing students.

    Science.gov (United States)

    Benedict, Kendra M; Johnson, Harold; Antia, Shirin D

    2011-01-01

    The purposes of the study were to obtain and analyze data on the need for, and desired characteristics of, faculty in deaf education at American institutions of higher education (IHEs), and to assess the present and projected status of doctoral-level teacher preparation programs in deaf education at American IHEs. Program directors and coordinators provided information on current and projected faculty openings, the number of active doctoral students, faculty research interests, program strengths, and needs in the field. Results indicated a pending shortage due to faculty retirements and a paucity of doctoral-level graduates. Most faculty listed literacy and language as a primary research interest as well as a program strength. The ability to generate new knowledge through research was found to be less desirable for future faculty than teaching ability. Suggestions for improving doctoral preparation and moving the field to evidence-based practices are provided.

  15. Preparation of Hard Coating Films with High Refractive Index from TiO{sub 2}-SnO{sub 2} Nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Chi Yong; Kim, Nam Woo; Song, Ki Chang [Konyang University, Nonsan (Korea, Republic of)

    2015-12-15

    TiO{sub 2}-SnO{sub 2} nanoparticles with an average diameter of 3-5 nm were synthesized by hydrolysis of titanium tetraisopropoxide (TTIP) and tin chloride to depress the photocatalytic activity of TiO{sub 2} nanoparticles. Organic-inorganic hybrid coating solutions were prepared by reacting the TiO{sub 2}-SnO{sub 2} nanoparticles with 3-glycidoxypropyl trimethoxysilane (GPTMS) by the sol-gel method. The hard coating films with high refractive index were obtained by curing thermally at 120 .deg. C after spin-coating the coating solutions on the polycarbonate (PC) sheets. The coating films from TiO{sub 2}- SnO{sub 2} nanoparticles showed an improved pencil hardness of 3H compared to 2H of the coating films from TiO{sub 2} nanoparticles. Besides, the refractive index of the coating films from TiO{sub 2}-SnO{sub 2} nanoparticles enhanced from 1.543 to 1.623 at 633 nm as the Sn/Ti molar ratio increased from 0 to 0.5.

  16. The Art of Copying

    DEFF Research Database (Denmark)

    Christensen, Hans Dam

    2017-01-01

    This article discusses copies within the field of art museums by way of mapping strategies for copy practices. This mapping leans heavily towards parts of the writings of Jacques Derrida (1930–2004). Against the backdrop of this theoretical premise, the article distinguishes five main strategies....... An informational copy is just as unique as an original object of art, and at the same time, it defines the original and is itself defined by this opposition. Lastly, the strategy for the imagined relation between original and copy follows. This strategy is dependent upon several of the previous approaches, and...

  17. The Art of Copying

    DEFF Research Database (Denmark)

    Christensen, Hans Dam

    2017-01-01

    This article discusses copies within the field of art museums by way of mapping strategies for copy practices. This mapping leans heavily towards parts of the writings of Jacques Derrida (1930–2004). Against the backdrop of this theoretical premise, the article distinguishes five main strategies...... for the informational originalcopy will be discussed as it has a vital function in terms of talking about museum originals and copies. This is the strategy which grants the original artifacts their status as museum objects. An informational originalcopy is just as unique as an original object of art, and at the same...

  18. Preparation

    Directory of Open Access Journals (Sweden)

    M.M. Dardir

    2014-03-01

    Full Text Available Some hexanamide-mono and di-linoleniate esters were prepared by the reaction of linolenic acid and hexanamide (derived from the reaction of hexanoic acid and diethanolamine. The chemical structure for the newly prepared hexanamide-mono and di-linoleniate esters were elucidated using elemental analysis, (FTIR, H 1NMR and chemical ionization mass spectra (CI/Ms spectroscopic techniques. The results of the spectroscopic analysis indicated that they were prepared through the right method and they have high purity. The new prepared esters have high biodegradability and lower toxicity (environmentally friendly so they were evaluated as a synthetic-based mud (ester-based mud for oil-well drilling fluids. The evaluation included study of the rheological properties, filtration and thermal properties of the ester based-muds formulated with the newly prepared esters compared to the reference commercial synthetic-based mud.

  19. Single-image hard copy display of musculoskeletal digital radiographs

    Science.gov (United States)

    Legendre, Kevin; Steller Artz, Dorothy E.; Freedman, Matthew T.; Mun, Seong K.

    1995-04-01

    Screen film radiography often fails to optimally display all regions of anatomy on muskuloskeletal exams due to the wide latitude of tissue densities present. Various techniques of image enhancement have been applied to such exams using computerized radiography but with limited success in improving visualization of structures whose final optical density lies at the extremes of the interpretable range of the film. An existing algorithm for compressing optical density extremes known as dynamic range compression has been used to increase the radiodensity of the retrocardiac region of the chest or to decrease the radiodensity of the edge of the breast in digital mammography. In the skeletal system, there are regions where a single image may contain both areas of decreased exposure that result in light images and areas of higher exposure that result in dark regions of the image. Faced with this problem, the senior author asked Fuji to formulate a modification of the DRC process that incorporates a combination of the curves used for chest and breast images. The newly designed algorithm can thus simultaneously lower the optical density of dark regions of the image and increase the optical density of the less exposed regions. The results of this modification of the DRC algorithm are presented in this paper.

  20. Investigation into digital print hard copy quality, longevity and durability

    Energy Technology Data Exchange (ETDEWEB)

    Kazlauciunas, Algy; Zhang Mingyu [Department of Colour Science, School of Chemistry, University of Leeds LS2 9JT (United Kingdom); Ball, Jeff, E-mail: ccdak@leeds.ac.u [Nazdar Limited, Heaton Mersey, Stockport, Cheshire SK4 3EG (United Kingdom)

    2010-06-01

    The main purpose of the research project was to investigate whether deskjet ink jet printing could produce A-4 size images on a par with conventional silver halide continuous tone photographic media prints. To this end, equivalent images were produced using both dye-based and pigment-based deskjet ink jet prints. To assist the research project, a multi-cultured array of observers were enlisted to give individual responses to a range of specific questions appertaining to the image characteristics of the A-4 size images produced. In addition, in order to assess the image stability and print durability of both the conventional silver halide prints and the ink jet prints, a range of laboratory tests were undertaken in the areas of light fastness, water fastness and both dry and wet rub fastness.

  1. Using DMA for copying performance counter data to memory

    Science.gov (United States)

    Gara, Alan; Salapura, Valentina; Wisniewski, Robert W

    2013-12-31

    A device for copying performance counter data includes hardware path that connects a direct memory access (DMA) unit to a plurality of hardware performance counters and a memory device. Software prepares an injection packet for the DMA unit to perform copying, while the software can perform other tasks. In one aspect, the software that prepares the injection packet runs on a processing core other than the core that gathers the hardware performance data.

  2. Watermark copy attack

    OpenAIRE

    Kutter, Martin; Voloshynovskyy, Svyatoslav; Herrigel, Alexander

    2000-01-01

    Research in digital watermarking has progressed along two paths. While new watermarking technologies are being developed, some researchers are also investigating di erent ways of attacking digital watermarks. Common attacks to watermarks usually aim to destroy theembedded watermark or to impair its detection. In this paper we propose a conceptually new attack for digitally watermarked images. The proposed attack doesnot destroy anembedded watermark, but copies it from one image to a di erent ...

  3. Standard hardness conversion tables for metals relationship among brinell hardness, vickers hardness, rockwell hardness, superficial hardness, knoop hardness, and scleroscope hardness

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2007-01-01

    1.1 Conversion Table 1 presents data in the Rockwell C hardness range on the relationship among Brinell hardness, Vickers hardness, Rockwell hardness, Rockwell superficial hardness, Knoop hardness, and Scleroscope hardness of non-austenitic steels including carbon, alloy, and tool steels in the as-forged, annealed, normalized, and quenched and tempered conditions provided that they are homogeneous. 1.2 Conversion Table 2 presents data in the Rockwell B hardness range on the relationship among Brinell hardness, Vickers hardness, Rockwell hardness, Rockwell superficial hardness, Knoop hardness, and Scleroscope hardness of non-austenitic steels including carbon, alloy, and tool steels in the as-forged, annealed, normalized, and quenched and tempered conditions provided that they are homogeneous. 1.3 Conversion Table 3 presents data on the relationship among Brinell hardness, Vickers hardness, Rockwell hardness, Rockwell superficial hardness, and Knoop hardness of nickel and high-nickel alloys (nickel content o...

  4. LC4铝合金表面硬质阳极氧化膜制备及表征%Preparation and Characterization of Hard Anodic Oxidation Film on LC4 Aluminum Alloy Surface

    Institute of Scientific and Technical Information of China (English)

    王英才; 陈岁元; 刘平平

    2014-01-01

    目的:在 LC4铝合金表面制备硬质阳极氧化膜,讨论工艺参数对膜层厚度和硬度的影响。方法对阳极氧化的时间、温度、电流密度及正负脉冲电流时间比等参数进行优化实验,通过 OM,SEM,XRD 及显微硬度计等对制备的氧化膜层的厚度、硬度、形貌等进行研究。结果工艺优化后的参数为:温度-2~0℃,正脉冲电流密度4 A/ dm2,负脉冲电流密度1 A/ dm2,正负脉冲电流时间比6:1,氧化时间50 min。得到由一系列直径约为50 nm 的管状单元结构组成的氧化膜,其厚度为36μm,硬度为420HV。结论制备的阳极氧化膜具有致密的组织结构和高的硬度值。%Objective The hard anodic oxidation films were prepared on the surface of the LC4 aluminum alloy and the effects of different parameters on the thickness and hardness of the films were discussed. Methods By optimizing parameters of the anodic ox-idation time, temperature, current density and the positive and negative pulse time ratio, the thickness, hardness and microstruc-ture of the films were studied by means of OM, SEM, XRD, and hardness tester. Results The optimized parameters were: a tem-perature of -2 ~ 0 ℃ , a positive pulse current density of 4 A/ dm2 , a negative pulse current density of 1 A/ dm2 , a positive and negative pulse current time ratio of 6 : 1, and an oxidation time of 50 min. The structure of the oxide film on LC4 aluminum alloy was composed of a series of tubular cells with a diameter of 50 nm, the thickness of anodic oxidation film was 36 μm, and the hard-ness was 420HV. Conclusion The anodic oxidation film had fine structure and high hardness.

  5. Robust Adaptable Video Copy Detection

    DEFF Research Database (Denmark)

    Assent, Ira; Kremer, Hardy

    2009-01-01

    Video copy detection should be capable of identifying video copies subject to alterations e.g. in video contrast or frame rates. We propose a video copy detection scheme that allows for adaptable detection of videos that are altered temporally (e.g. frame rate change) and/or visually (e.g. change...... in contrast). Our query processing combines filtering and indexing structures for efficient multistep computation of video copies under this model. We show that our model successfully identifies altered video copies and does so more reliably than existing models....

  6. Robust Adaptable Video Copy Detection

    DEFF Research Database (Denmark)

    Assent, Ira; Kremer, Hardy

    2009-01-01

    Video copy detection should be capable of identifying video copies subject to alterations e.g. in video contrast or frame rates. We propose a video copy detection scheme that allows for adaptable detection of videos that are altered temporally (e.g. frame rate change) and/or visually (e.g. change...... in contrast). Our query processing combines filtering and indexing structures for efficient multistep computation of video copies under this model. We show that our model successfully identifies altered video copies and does so more reliably than existing models....

  7. The Effect of Thermo-mechanical Treatment of Substrate Preparation and Carburizing Temperature on The Morphology and Hardness of Carburizing on Low Carbon Steel

    Science.gov (United States)

    Dadan Ramdan, Raden; Adetia, Andra; Suratman, Rochim

    2017-07-01

    Low carbon steel has a lot of applications in daily life because of its excellent properties. Among its excellent properties are good ductility, toughness, formability, and weldability. For the case of application that requires good wear resistant, carbon steel is not sufficient. For this case it is required to increase the hardness of carbon steel, such as by carburizing method. In this method one factor that affects the carburizing layer is metal substrate condition, i.e grain size. Another factor is temperature that could have significant role on the carburized layer characteristics. Therefore the present works focus in the correlation between degree of reduction of cold rolling and carburizing temperature on the carburized layer characteristic. Thermo-mechanical treatment was applied to the specimen with reduction of 0%, 30%, and 80% by mean of rolling before carburizing process. Carburizing processes were carried out at temperature of 850°C, 900°C, and 950°C. Examinations on carburized specimens were conducted by metallography and micro hardness test. The result showed that the specimen of 80% reduction giving the thickest layer and the hardest surface layer. In addition, at temperature of 900°C, the hardest layer was formed with the hardness at 1003 HV. However, the thickest layer was formed at the temperature of 950°C.

  8. Bio-relevant dissolution testing of hard capsules prepared from different shell materials using the dynamic open flow through test apparatus.

    Science.gov (United States)

    Garbacz, Grzegorz; Cadé, Dominique; Benameur, Hassan; Weitschies, Werner

    2014-06-16

    Current compendial dissolution and disintegrating testing is unable to mimic physiological conditions affecting gastric drug release from immediate release dosage forms. In order to obtain more realistic data, a novel test setup was developed that we term a 'dynamic open flow through test apparatus'. It is based on the previously described dissolution stress test device and attempts to simulate the intra-gastric dissolution conditions pertinent to immediate release dosage forms administered under fasting conditions with respect to flow rates, intra-gastric temperature profiles and gastric motility. The concept of the dynamic open flow through test apparatus has been tested using five different types of hard capsules: conventional hard gelatin capsules (HGC), three hypromellose based capsules (Vcaps, Vcaps Plus and DRcaps) and pullulan based capsules (Plantcaps). These were of different sizes but all contained 100mg caffeine in each formulation, adjusted to avoid buoyancy by addition of excipient. When the capsules were stressed in the apparatus under the dynamic flow conditions applying mild pressure simulating gastric motility, release from release from Vcaps Plus, Vcaps and Plantcaps capsules was very well comparable to HGC. Capsules are usually swallowed with cold water and the temperature dependency of release from gelatin was noted as a significant factor, since heat exchange in the stomach is slow. Copyright © 2013 Elsevier B.V. All rights reserved.

  9. Color of whole-wheat foods prepared from a bright-white hard winter wheat and the phenolic acids in its coarse bran.

    Science.gov (United States)

    Jiang, Hongxin; Martin, Joe; Okot-Kotber, Moses; Seib, Paul A

    2011-08-01

    The color of wheat kernels often impacts the color and thereby the value of wheat-based foods. A line of hard white winter wheat (B-W HW) with bright appearing kernels has been developed at the Kansas State Agricultural Research Center. The objective of this study was to compare the color of several foods made from the B-W HW wheat with those of 2 hard white wheat cultivars, Trego and Lakin. The B-W HW kernels showed higher lightness (L*, 57.6) than Trego (55.5) and Lakin (56.8), and the increased lightness was carried over to its bran and whole-wheat flour. Alkaline noodle and bread crumb made from the B-W HW whole-wheat flour showed slightly higher lightness (L*) than those made from Trego and Lakin. The sum of soluble and bound phenolics extracted from the 3 wheat brans, which had not been preextracted to remove lipids, was found to be 17.22 to 18.98 mg/g. The soluble phenolic acids in the brans were principally vanillic, ferulic, and syringic. The bound phenolic acids in the brans were dominated by ferulic, which accounted for 50.1% to 82.2% of total identified bound phenolic acids. Other bound phenolic acids were protocatechuic, caffeic, syringic, trans-cinnamic, p-hydroxybenzoic, p-coumaric, and vanillic. The lightness (L*) values of coarse wheat brans correlated positively with their levels of bound protocatechuic (r = 0.72, P < 0.01) and p-hydroxybenzoic acids (r = 0.75, P < 0.01).

  10. A hard-template method for the preparation of IrO(2) , and its performance in a solid-polymer-electrolyte water electrolyzer.

    Science.gov (United States)

    Li, Guangfu; Yu, Hongmei; Song, Wei; Dou, Meiling; Li, Yongkun; Shao, Zhigang; Yi, Baolian

    2012-05-01

    Morphological control by SBA-15: The performance of catalysts for the oxygen evolution reaction (OER) depends strongly on their structural and morphological properties. An IrO(2) nanomaterial with a morphology suitable for the OER is prepared by using a synthetic scheme involving a zeolite template, and shows enhanced activity and stability compared to IrO(2) fabricated by the traditional Adams-fusion method.

  11. CNARA: reliability assessment for genomic copy number profiles.

    Science.gov (United States)

    Ai, Ni; Cai, Haoyang; Solovan, Caius; Baudis, Michael

    2016-10-12

    DNA copy number profiles from microarray and sequencing experiments sometimes contain wave artefacts which may be introduced during sample preparation and cannot be removed completely by existing preprocessing methods. Besides, large derivative log ratio spread (DLRS) of the probes correlating with poor DNA quality is sometimes observed in genome screening experiments and may lead to unreliable copy number profiles. Depending on the extent of these artefacts and the resulting misidentification of copy number alterations/variations (CNA/CNV), it may be desirable to exclude such samples from analyses or to adapt the downstream data analysis strategy accordingly. Here, we propose a method to distinguish reliable genomic copy number profiles from those containing heavy wave artefacts and/or large DLRS. We define four features that adequately summarize the copy number profiles for reliability assessment, and train a classifier on a dataset of 1522 copy number profiles from various microarray platforms. The method can be applied to predict the reliability of copy number profiles irrespective of the underlying microarray platform and may be adapted for those sequencing platforms from which copy number estimates could be computed as a piecewise constant signal. Further details can be found at https://github.com/baudisgroup/CNARA . We have developed a method for the assessment of genomic copy number profiling data, and suggest to apply the method in addition to and after other state-of-the-art noise correction and quality control procedures. CNARA could be instrumental in improving the assessment of data used for genomic data mining experiments and support the reliable functional attribution of copy number aberrations especially in cancer research.

  12. Mate Choice Copying in Humans.

    Science.gov (United States)

    Waynforth, D

    2007-09-01

    There is substantial evidence that in human mate choice, females directly select males based on male display of both physical and behavioral traits. In non-humans, there is additionally a growing literature on indirect mate choice, such as choice through observing and subsequently copying the mating preferences of conspecifics (mate choice copying). Given that humans are a social species with a high degree of sharing information, long-term pair bonds, and high parental care, it is likely that human females could avoid substantial costs associated with directly searching for information about potential males by mate choice copying. The present study was a test of whether women perceived men to be more attractive when men were presented with a female date or consort than when they were presented alone, and whether the physical attractiveness of the female consort affected women's copying decisions. The results suggested that women's mate choice decision rule is to copy only if a man's female consort is physically attractive. Further analyses implied that copying may be a conditional female mating tactic aimed at solving the problem of informational constraints on assessing male suitability for long-term sexual relationships, and that lack of mate choice experience, measured as reported lifetime number of sex partners, is also an important determinant of copying.

  13. Effect of low-content of carbon nanotubes on the fracture toughness and hardness of carbon nanotube reinforced alumina prepared by sinter, HIP and sinter  +  HIP routes

    Science.gov (United States)

    Bocanegra-Bernal, M. H.; Dominguez-Rios, C.; Echeberria, J.; Reyes-Rojas, A.; Garcia-Reyes, A.; Aguilar-Elguezabal, A.

    2017-08-01

    Alumina ceramic composites were prepared with additions of 0.1 wt% of different kinds of carbon nanotubes (CNTs) by pressureless sintering (PLS), hot isostatic pressing (HIP) and sintering  +  hot isostatic pressing (sinter  +  HIP) routes. The composites showed relative density higher than 94% with a wide range of grain sizes and fracture toughness values, while the hardness remained practically the same. For the same content of CNTs, some isolated mechanisms associated with toughening behaviour such as crack deflection, crack bridging, and CNT pull-out were exhibited in some composites. Since the same dispersion process was used for all composites, the differences found in the homogeneity of the CNTs within the matrix are due to their intrinsic characteristics combined with the fabrication routes. As a result, the best performance was obtained for the alumina composite with CNT identified as MWCNT-CIMAV, for which the fracture toughness increased 63% as compared to monolithic alumina, both prepared by the HIP route.

  14. Preparation of hard magnetic materials based on nitrogenated rare-earth iron alloys; Preparacao de materiais magneticamente duros a base de ligas de terra rara - ferro nitrogenadas

    Energy Technology Data Exchange (ETDEWEB)

    Guilherme, Eneida da Graca

    1999-07-01

    Nd Fe{sub 11}Ti, Nd Fe{sub 10.5} Mo{sub 1.5} and Nd Fe{sub 10.75} Mo{sub 1.25} alloys were synthesized by reduction-diffusion calciothermic process (RDC) from neodymium chloride (NdCl{sub 3}), iron, titanium, molybdenum and reduction agent (metallic calcium). The effect of process variables, like temperature, time, excess amount of NdCl{sub 3}, heating rate, and composition variation of the Nd Fe{sub 12-x}Mo{sub x} (1 {>=} x {>=} 2). Mother alloys in which 1:12 phase is major were nitrogenated by gas-solid reaction with N{sub 2} and by chemical reaction with sodium zide (Na N{sub 3}). In addition, the influence of reducing particle size of the powdered mother alloys in the nitrogenation step with Na N{sub 3} were studied. As prepared and interstitially modified Nd Fe{sub 11} Ti, Nd Fe{sub 10.5} Mo{sub 1.5} and Nd Fe{sub 10.75} Mo{sub 1.25} alloys with nitrogen , were characterized by X-ray diffraction, Moessbauer spectroscopy, thermomagnetic, SEM and EDS. Nitrogenation by gas-solid reaction with N{sub 2} is found to be not promising, since resulted Curie temperatures (Tc) were lower than literature values. However, nitrogenation by chemical reaction with Na N{sub 3} was efficient with higher or same Tc than previous reported results. The average increases on Tc and volumetric expansion were 200 deg C and 4%, respectively. Milling of the mother alloys before nitrogenation at 330 deg C is preferred because reaction kinetics is enhanced. Nevertheless, at 450 deg C, a competition between the interstitially modified compound formation (alloy + N) and alloy dissociation has occurred, resulting in a Fe-{alpha} phase increase. (author)

  15. International perspectives on coal preparation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    The report consists of the vugraphs from the presentations which covered the following topics: Summaries of the US Department of Energy`s coal preparation research programs; Preparation trends in Russia; South African coal preparation developments; Trends in hard coal preparation in Germany; Application of coal preparation technology to oil sands extraction; Developments in coal preparation in China; and Coal preparation in Australia.

  16. Zero-Copy Objects System

    Science.gov (United States)

    Burleigh, Scott C.

    2011-01-01

    Zero-Copy Objects System software enables application data to be encapsulated in layers of communication protocol without being copied. Indirect referencing enables application source data, either in memory or in a file, to be encapsulated in place within an unlimited number of protocol headers and/or trailers. Zero-copy objects (ZCOs) are abstract data access representations designed to minimize I/O (input/output) in the encapsulation of application source data within one or more layers of communication protocol structure. They are constructed within the heap space of a Simple Data Recorder (SDR) data store to which all participating layers of the stack must have access. Each ZCO contains general information enabling access to the core source data object (an item of application data), together with (a) a linked list of zero or more specific extents that reference portions of this source data object, and (b) linked lists of protocol header and trailer capsules. The concatenation of the headers (in ascending stack sequence), the source data object extents, and the trailers (in descending stack sequence) constitute the transmitted data object constructed from the ZCO. This scheme enables a source data object to be encapsulated in a succession of protocol layers without ever having to be copied from a buffer at one layer of the protocol stack to an encapsulating buffer at a lower layer of the stack. For large source data objects, the savings in copy time and reduction in memory consumption may be considerable.

  17. Effect of sulfuric acid on textural properties and catalytic performance of ruthenium-containing ordered mesoporous carbon prepared via a direct RuCl3/SBA-15 hard templated method.

    Science.gov (United States)

    Lan, Guojun; Tang, Haodong; Liu, Huazhang; Ni, Jun; Li, Ying

    2014-09-01

    Ruthenium-containing ordered mesoporous carbon (Ru-OMC) catalysts with highly dispersed Ru nanoparticles semi-embedded in carbon framework were prepared via a direct RuCl3/SBA-15 hard templated method. The effect of sulfuric acid on the texture structure and catalytic performance of Ru-OMC were studied. The status of Ru nanoparticles and mesoporous structure of Ru-OMC catalysts were characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), nitrogen sorption, scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and CO chemisorption techniques. The addition of appropriate amount of sulfuric acid is necessary to improve the ordered mesoporous structure of Ru-OMC catalysts. The framework of carbon structure shrinks with the increase in sulfur acid contents, which is proved by a slight decrease in surface area and increase in pore diameters for Ru-OMC with different sulfur contents. The turnover frequency (TOF) for Ru-OMC reaches the highest up to 3.98 s(-1) in benzene hydrogenation with optimized sulfur acid content of 0.08 mmol/g sucrose.

  18. Thermodynamic hardness and the maximum hardness principle

    Science.gov (United States)

    Franco-Pérez, Marco; Gázquez, José L.; Ayers, Paul W.; Vela, Alberto

    2017-08-01

    An alternative definition of hardness (called the thermodynamic hardness) within the grand canonical ensemble formalism is proposed in terms of the partial derivative of the electronic chemical potential with respect to the thermodynamic chemical potential of the reservoir, keeping the temperature and the external potential constant. This temperature dependent definition may be interpreted as a measure of the propensity of a system to go through a charge transfer process when it interacts with other species, and thus it keeps the philosophy of the original definition. When the derivative is expressed in terms of the three-state ensemble model, in the regime of low temperatures and up to temperatures of chemical interest, one finds that for zero fractional charge, the thermodynamic hardness is proportional to T-1(I -A ) , where I is the first ionization potential, A is the electron affinity, and T is the temperature. However, the thermodynamic hardness is nearly zero when the fractional charge is different from zero. Thus, through the present definition, one avoids the presence of the Dirac delta function. We show that the chemical hardness defined in this way provides meaningful and discernible information about the hardness properties of a chemical species exhibiting integer or a fractional average number of electrons, and this analysis allowed us to establish a link between the maximum possible value of the hardness here defined, with the minimum softness principle, showing that both principles are related to minimum fractional charge and maximum stability conditions.

  19. Wear of hard materials by hard particles

    Energy Technology Data Exchange (ETDEWEB)

    Hawk, Jeffrey A.

    2003-10-01

    Hard materials, such as WC-Co, boron carbide, titanium diboride and composite carbide made up of Mo2C and WC, have been tested in abrasion and erosion conditions. These hard materials showed negligible wear in abrasion against SiC particles and erosion using Al2O3 particles. The WC-Co materials have the highest wear rate of these hard materials and a very different material removal mechanism. Wear mechanisms for these materials were different for each material with the overall wear rate controlled by binder composition and content and material grain size.

  20. Study on Preparation and Stability of Garlic Oil Liquid-filled Hard Capsules%大蒜油液体硬胶囊剂的制备及稳定性考察

    Institute of Scientific and Technical Information of China (English)

    杨志彬; 刘海; 王宝树

    2013-01-01

    将大蒜油与其他基质混合后灌装于明胶硬胶囊中,用封口液封口,得到大蒜油液体硬胶囊.对产品的性状、大蒜素含量和溶出度进行了检测,考察其在光照、不同温度和湿度条件下的稳定性.结果表明,制备的大蒜油液体硬胶囊为黄色透明硬胶囊,无臭.油溶性基质的大蒜油液体硬胶囊在光照、高温和湿度75.0%的条件下稳定,大蒜素含量和溶出度检测结果合格,在湿度92.5%条件下胶囊易软化;而水溶性基质的大蒜油液体硬胶囊在高温和高湿条件下不稳定,易变脆或软化.加速试验结果表明油溶性基质的大蒜油液体硬胶囊在温度40℃、湿度75.0%条件下放置180d各项指标基本稳定.%Garlic oil liquid-filled capsules were prepared by mixing garlic oil with other matrix,then filled into hard gelatin capsules and sealed.Stability test were conducted to inspect the properties,relative allicin content and dissolution of products under light,different temperature and humidity conditions.The results showed that the garlic oil liquid-filled capsules were hard capsules with transparent yellow and had no odor.The garlic oil liquid-filled capsules with oil-soluble matrix were stable under light,high temperature and 75% humidity conditions,the relative allicin content and dissolution of products were qualified; however,under the condition of 92.5% humidity,the capsules were easy to soften.Garlic oil liquid-filled capsules with water-soluble matrix were instable under high temperature or high humidity conditions,as they were easy to soften and crisp.Accelerated tests showed that indicators of garlic oil liquid-filled capsules with oil-soluble matrix were basically stable under the condition of 40 ℃,75% humidity for 180 d.

  1. 电弧离子镀法制备高硬度Cr-Si-C-N薄膜%Cr-Si-C-N HARD FILMS PREPARED BY ARC ION DEPOSITION METHOD

    Institute of Scientific and Technical Information of China (English)

    聂朝胤; Akiro Ando; 卢春灿; 贾晓芳

    2009-01-01

    采用电弧离子反应沉积技术在SCM415渗碳淬火钢基片上沉积了Cr-Si-C-N薄膜,三甲基硅烷(TMS)反应气体作为Si和C掺杂源,通过改变TMS流量实现了薄膜中si和C含量的调节.利用XPS,XRD,HRTEM和显微硬度计研究了Cr-Si-C-N薄膜的化学状态、显微组织和显微硬度.Cr-Si-C-N薄膜中的Si和C含量随TMS流量的增加而单调增加.在TMS流鼍小于:90 mL/min时,薄膜中Si和C含量较少,薄膜由Cr(C,N)纳米晶与Si_3N_4非品(nc-Cr(C,N)/a-Si_3N_4)组成,薄膜硬度随流量的增加而单调增大,最大至4500 HK.硬度的增加源于固溶强化及薄膜中纳米晶/非晶复合结构的形成;当TMS流量大于90 mL/min时,薄膜中Si和C含量较多,多余的C以游离态形式存在,且随TMS流量的增加而增多,薄膜硬度下降.%PVD or CVD Me-Si N nanocomposite films synthesized by doping Si element in metallic nitride matrix have exhibited good oxidation resistance and wear resistance. As melting the alloy target containing Si is not easy, it is difficulty to dope much more Si in the fihns by PVD techniques. In addition, the Me-Si-N films do not have enough lubrication. In this paper, Cr-Si-C-N films were prepared by cathode arc ion deposition technique, in which tetramethylsilane (TMS) was used as Si and C sources, and their concentrations in the Cr-Si-C-N fihns can be controlled by TMS flow. The state of chemical bonding, microstructure and microhardncss were investigated by XPS, XRD, HRTEM and microindentation hardness tester. Results show that the Si and C contents increase monotonicly with the increase of TMS flow. When the TMS flow is lower than 90 mL/min, the Cr-Si-C-N fihn has a composite structure of Cr(C, N) nanocrystals dispersing in the amorphous Si_3N_4 (nc-Cr(C, N)/a-Si_3N_4), and the microhardness increases to 4500 HK with increas-ing TMS flow. Such high hardness originates from the solid solution hardening of the doping fewer element and the Veprek nanocompositc structure

  2. Some bounds for quantum copying

    CERN Document Server

    Rastegin, A E

    2001-01-01

    We derive lower bounds on the absolute error and the relative error of an abstract copying of two-state set. We do not specify a copying transformation and a dimension of state space. Only the unitarity of quantum mechanical transformations is used. Our approach is based on the notion of angle between two states. We first prove several useful statements, simply expressed in terms of angles. We then examine a lower bound on the absolute error, that was first considered by Hillery and Buzek. Our reasonings supplement and reinforce the results, obtained by them. So, we derive more strong bounds on the absolute error, and we also consider a tradeoff between size of error and corresponding probability distributions. After that we examine a lower bound on the relative error.

  3. Hard processes in hadronic interactions

    Energy Technology Data Exchange (ETDEWEB)

    Satz, H. [CERN, Geneva (Switzerland)]|[Universitat Bielefeld (Germany); Wang, X.N. [Lawrence Berkeley Lab., CA (United States)

    1995-07-01

    Quantum chromodynamics is today accepted as the fundamental theory of strong interactions, even though most hadronic collisions lead to final states for which quantitative QCD predictions are still lacking. It therefore seems worthwhile to take stock of where we stand today and to what extent the presently available data on hard processes in hadronic collisions can be accounted for in terms of QCD. This is one reason for this work. The second reason - and in fact its original trigger - is the search for the quark-gluon plasma in high energy nuclear collisions. The hard processes to be considered here are the production of prompt photons, Drell-Yan dileptons, open charm, quarkonium states, and hard jets. For each of these, we discuss the present theoretical understanding, compare the resulting predictions to available data, and then show what behaviour it leads to at RHIC and LHC energies. All of these processes have the structure mentioned above: they contain a hard partonic interaction, calculable perturbatively, but also the non-perturbative parton distribution within a hadron. These parton distributions, however, can be studied theoretically in terms of counting rule arguments, and they can be checked independently by measurements of the parton structure functions in deep inelastic lepton-hadron scattering. The present volume is the work of Hard Probe Collaboration, a group of theorists who are interested in the problem and were willing to dedicate a considerable amount of their time and work on it. The necessary preparation, planning and coordination of the project were carried out in two workshops of two weeks` duration each, in February 1994 at CERn in Geneva andin July 1994 at LBL in Berkeley.

  4. Role of water hardness in rinsing bacteria from the skin of processed broiler chickens

    Science.gov (United States)

    The effect of water hardness on the ability of water to rinse bacteria from the skin of processed broiler chickens was examined. Artificial hard water with a total hardness of 200 ppm (very hard water) was prepared by dissolving calcium chloride (CaCl2) and magnesium chloride hexahydrate (MgCl2 •6H2...

  5. Hardness Tester for Polyur

    Science.gov (United States)

    Hauser, D. L.; Buras, D. F.; Corbin, J. M.

    1987-01-01

    Rubber-hardness tester modified for use on rigid polyurethane foam. Provides objective basis for evaluation of improvements in foam manufacturing and inspection. Typical acceptance criterion requires minimum hardness reading of 80 on modified tester. With adequate correlation tests, modified tester used to measure indirectly tensile and compressive strengths of foam.

  6. Comprehensive hard materials

    CERN Document Server

    2014-01-01

    Comprehensive Hard Materials deals with the production, uses and properties of the carbides, nitrides and borides of these metals and those of titanium, as well as tools of ceramics, the superhard boron nitrides and diamond and related compounds. Articles include the technologies of powder production (including their precursor materials), milling, granulation, cold and hot compaction, sintering, hot isostatic pressing, hot-pressing, injection moulding, as well as on the coating technologies for refractory metals, hard metals and hard materials. The characterization, testing, quality assurance and applications are also covered. Comprehensive Hard Materials provides meaningful insights on materials at the leading edge of technology. It aids continued research and development of these materials and as such it is a critical information resource to academics and industry professionals facing the technological challenges of the future. Hard materials operate at the leading edge of technology, and continued res...

  7. Hard template synthesis of metal nanowires

    Directory of Open Access Journals (Sweden)

    Go eKawamura

    2014-11-01

    Full Text Available Metal nanowires (NWs have attracted much attention because of their high electron conductivity, optical transmittance and tunable magnetic properties. Metal NWs have been synthesized using soft templates such as surface stabilizing molecules and polymers, and hard templates such as anodic aluminum oxide, mesoporous oxide, carbon nanotubes. NWs prepared from hard templates are composites of metals and the oxide/carbon matrix. Thus, selecting appropriate elements can simplify the production of composite devices. The resulting NWs are immobilized and spatially arranged, as dictated by the ordered porous structure of the template. This avoids the NWs from aggregating, which is common for NWs prepared with soft templates in solution. Herein, the hard template synthesis of metal NWs is reviewed, and the resulting structures, properties and potential applications are discussed.

  8. Patterns, correlates, and reduction of homework copying

    Science.gov (United States)

    Palazzo, David J.; Lee, Young-Jin; Warnakulasooriya, Rasil; Pritchard, David E.

    2010-06-01

    Submissions to an online homework tutor were analyzed to determine whether they were copied. The fraction of copied submissions increased rapidly over the semester, as each weekly deadline approached and for problems later in each assignment. The majority of students, who copied less than 10% of their problems, worked steadily over the three days prior to the deadline, whereas repetitive copiers (those who copied >30% of their submitted problems) exerted little effort early. Importantly, copying homework problems that require an analytic answer correlates with a 2(σ) decline over the semester in relative score for similar problems on exams but does not significantly correlate with the amount of conceptual learning as measured by pretesting and post-testing. An anonymous survey containing questions used in many previous studies of self-reported academic dishonesty showed ˜1/3 less copying than actually was detected. The observed patterns of copying, free response questions on the survey, and interview data suggest that time pressure on students who do not start their homework in a timely fashion is the proximate cause of copying. Several measures of initial ability in math or physics correlated with copying weakly or not at all. Changes in course format and instructional practices that previous self-reported academic dishonesty surveys and/or the observed copying patterns suggested would reduce copying have been accompanied by more than a factor of 4 reduction of copying from ˜11% of all electronic problems to less than 3%. As expected (since repetitive copiers have approximately three times the chance of failing), this was accompanied by a reduction in the overall course failure rate. Survey results indicate that students copy almost twice as much written homework as online homework and show that students nationally admit to more academic dishonesty than MIT students.

  9. Patterns, correlates, and reduction of homework copying

    Directory of Open Access Journals (Sweden)

    David J. Palazzo

    2010-03-01

    Full Text Available Submissions to an online homework tutor were analyzed to determine whether they were copied. The fraction of copied submissions increased rapidly over the semester, as each weekly deadline approached and for problems later in each assignment. The majority of students, who copied less than 10% of their problems, worked steadily over the three days prior to the deadline, whereas repetitive copiers (those who copied >30% of their submitted problems exerted little effort early. Importantly, copying homework problems that require an analytic answer correlates with a 2(σ decline over the semester in relative score for similar problems on exams but does not significantly correlate with the amount of conceptual learning as measured by pretesting and post-testing. An anonymous survey containing questions used in many previous studies of self-reported academic dishonesty showed ∼1/3 less copying than actually was detected. The observed patterns of copying, free response questions on the survey, and interview data suggest that time pressure on students who do not start their homework in a timely fashion is the proximate cause of copying. Several measures of initial ability in math or physics correlated with copying weakly or not at all. Changes in course format and instructional practices that previous self-reported academic dishonesty surveys and/or the observed copying patterns suggested would reduce copying have been accompanied by more than a factor of 4 reduction of copying from ∼11% of all electronic problems to less than 3%. As expected (since repetitive copiers have approximately three times the chance of failing, this was accompanied by a reduction in the overall course failure rate. Survey results indicate that students copy almost twice as much written homework as online homework and show that students nationally admit to more academic dishonesty than MIT students.

  10. Dynamic hardness of metals

    Science.gov (United States)

    Liang, Xuecheng

    Dynamic hardness (Pd) of 22 different pure metals and alloys having a wide range of elastic modulus, static hardness, and crystal structure were measured in a gas pulse system. The indentation contact diameter with an indenting sphere and the radius (r2) of curvature of the indentation were determined by the curve fitting of the indentation profile data. r 2 measured by the profilometer was compared with that calculated from Hertz equation in both dynamic and static conditions. The results indicated that the curvature change due to elastic recovery after unloading is approximately proportional to the parameters predicted by Hertz equation. However, r 2 is less than the radius of indenting sphere in many cases which is contradictory to Hertz analysis. This discrepancy is believed due to the difference between Hertzian and actual stress distributions underneath the indentation. Factors which influence indentation elastic recovery were also discussed. It was found that Tabor dynamic hardness formula always gives a lower value than that directly from dynamic hardness definition DeltaE/V because of errors mainly from Tabor's rebound equation and the assumption that dynamic hardness at the beginning of rebound process (Pr) is equal to kinetic energy change of an impact sphere over the formed crater volume (Pd) in the derivation process for Tabor's dynamic hardness formula. Experimental results also suggested that dynamic to static hardness ratio of a material is primarily determined by its crystal structure and static hardness. The effects of strain rate and temperature rise on this ratio were discussed. A vacuum rotating arm apparatus was built to measure Pd at 70, 127, and 381 mum sphere sizes, these results exhibited that Pd is highly depended on the sphere size due to the strain rate effects. P d was also used to substitute for static hardness to correlate with abrasion and erosion resistance of metals and alloys. The particle size effects observed in erosion were

  11. Hardness and excitation energy

    Indian Academy of Sciences (India)

    Á Nagy

    2005-09-01

    The concept of the ensemble Kohn-Sham hardness is introduced. It is shown that the first excitation energy can be given by the Kohn-Sham hardness (i.e. the energy difference of the ground-state lowest unoccupied and highest occupied levels) plus an extra term coming from the partial derivative of the ensemble exchange-correlation energy with respect to the weighting factor in the limit → 0. It is proposed that the first excitation energy can be used as a reactivity index instead of the hardness.

  12. Breaking the COPI monopoly on Golgi recycling.

    Science.gov (United States)

    Storrie, B; Pepperkok, R; Nilsson, T

    2000-09-01

    The unexpected discovery of a transport pathway from the Golgi to the endoplasmic reticulum (ER) independent of COPI coat proteins sheds light on how Golgi resident enzymes and protein toxins gain access to the ER from as far as the trans Golgi network. This new pathway provides an explanation for how membrane is recycled to allow for an apparent concentration of anterograde cargo at distinct stages of the secretory pathway. As signal-mediated COPI-dependent recycling also involves the concentration of resident proteins into retrograde COPI vesicles, the main bulk of lipids must be recycled, possibly through a COPI-independent pathway.

  13. Hardness Analysis. Training Module 5.215.2.77.

    Science.gov (United States)

    Bonte, John L.; Davidson, Arnold C.

    This document is an instructional module package prepared in objective form for use by an instructor familiar with hardness analysis using the EDTA method and the calculation of hardness given metal ion concentrations and a factor table. Included are objectives, an instructor guide, student handouts, and transparency masters. A video tape is also…

  14. Hard probes 2006 Asilomar

    CERN Multimedia

    2006-01-01

    "The second international conference on hard and electromagnetic probes of high-energy nuclear collisions was held June 9 to 16, 2006 at the Asilomar Conference grounds in Pacific Grove, California" (photo and 1/2 page)

  15. Hard and Soft

    OpenAIRE

    Claes H. de Vreese; Boomgaarden, Hajo G.; Semetko, Holli A.

    2008-01-01

    Abstract Support for European integration is a function no longer only of `hard' economic and utilitarian predictors but also of `soft' predictors such as feelings of identity and attitudes towards immigrants. Focusing on the issue of the potential membership of Turkey in the European Union (EU), this study demonstrates that the importance of `soft' predictors outweighs the role of `hard' predictors in understanding public opinion about Turkish membership. The study draws on survey...

  16. 21 CFR 133.148 - Hard grating cheeses.

    Science.gov (United States)

    2010-04-01

    ... than 32 percent of milkfat, as determined by the methods prescribed in § 133.5 (a), (b), and (d). Hard... harmless preparation of enzymes of animal or plant origin capable of aiding in the curing or development...

  17. Hardness amplification in nondeterministic logspace

    OpenAIRE

    Gupta, Sushmita

    2007-01-01

    A hard problem is one which cannot be easily computed by efficient algorithms. Hardness amplification is a procedure which takes as input a problem of mild hardness and returns a problem of higher hardness. This is closely related to the task of decoding certain error-correcting codes. We show amplification from mild average case hardness to higher average case hardness for nondeterministic logspace and worst-to-average amplification for nondeterministic linspace. Finally we explore possible ...

  18. UV curable hard coatings on polyesters

    Science.gov (United States)

    Datashvili, Tea; Brostow, Witold; Kao, David

    2006-10-01

    UV curable, hard and transparent hybrid inorganic-organic coatings with covalent links between the inorganic and the organic networks were prepared using organically crosslinked heteropolysiloxanes based on the sol-gel process. The materials were applied onto polyester sheets and UV cured. The deposition was followed by a thermal treatment to improve mechanical properties of the coatings. High light transmission and the resulting thermophysical properties indicate the presence of a nanoscale hybrid composition. The coatings show excellent adhesion to polyesters even without using primers. Further mechanical characterization shows that the coatings provide high hardness and good abrasion resistance.

  19. Private Copying and Downloading from Unlawful Sources

    NARCIS (Netherlands)

    Quintais, J.P.

    2015-01-01

    Private copying is one of the most contested areas of EU copyright law. This paper surveys that nebulous area and examines the issue of copies made from unlawful sources in light of the ECJ’s ACI Adam decision. After describing the legal background of copyright levies and the facts of the

  20. Private Copying and Downloading from Unlawful Sources

    NARCIS (Netherlands)

    J.P. Quintais

    2015-01-01

    Private copying is one of the most contested areas of EU copyright law. This paper surveys that nebulous area and examines the issue of copies made from unlawful sources in light of the ECJ’s ACI Adam decision. After describing the legal background of copyright levies and the facts of the litigation

  1. Hacking DNA copy number for circuit engineering.

    Science.gov (United States)

    Wu, Feilun; You, Lingchong

    2017-07-27

    DNA copy number represents an essential parameter in the dynamics of synthetic gene circuits but typically is not explicitly considered. A new study demonstrates how dynamic control of DNA copy number can serve as an effective strategy to program robust oscillations in gene expression circuits.

  2. 14 CFR 249.4 - Photographic copies.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Photographic copies. 249.4 Section 249.4 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) ECONOMIC REGULATIONS PRESERVATION OF AIR CARRIER RECORDS General Instructions § 249.4 Photographic copies. (a)...

  3. Dietetic Aide. [Teacher's Copy]. Revised.

    Science.gov (United States)

    Texas Education Agency, Austin. Dept. of Occupational Education and Technology.

    The curriculum guide, one of a series prepared to assist teacher-coordinators in promoting and teaching home economics cooperative education programs, provides a course of study for the dietetic aide occupation. In addition to a brief overview, job description, and job analysis of the occupation, the guide's four main sections are: instructional…

  4. Hard and superhard nanocomposite coatings

    Energy Technology Data Exchange (ETDEWEB)

    Musil, J. [Univ. of West Bohemia, Plzen (Czech Republic). Dept. of Phys.

    2000-03-01

    This article reviews the development of hard coatings from a titanium nitride film through superlattice coatings to nanocomposite coatings. Significant attention is devoted to hard and superhard single layer nanocomposite coatings. A strong correlation between the hardness and structure of nanocomposite coatings is discussed in detail. Trends in development of hard nanocomposite coatings are also outlined. (orig.)

  5. Session: Hard Rock Penetration

    Energy Technology Data Exchange (ETDEWEB)

    Tennyson, George P. Jr.; Dunn, James C.; Drumheller, Douglas S.; Glowka, David A.; Lysne, Peter

    1992-01-01

    This session at the Geothermal Energy Program Review X: Geothermal Energy and the Utility Market consisted of five presentations: ''Hard Rock Penetration - Summary'' by George P. Tennyson, Jr.; ''Overview - Hard Rock Penetration'' by James C. Dunn; ''An Overview of Acoustic Telemetry'' by Douglas S. Drumheller; ''Lost Circulation Technology Development Status'' by David A. Glowka; ''Downhole Memory-Logging Tools'' by Peter Lysne.

  6. Hard-hat day

    CERN Multimedia

    2003-01-01

    CERN will be organizing a special information day on Friday, 27th June, designed to promote the wearing of hard hats and ensure that they are worn correctly. A new prevention campaign will also be launched.The event will take place in the hall of the Main Building from 11.30 a.m. to 2.00 p.m., when you will be able to come and try on various models of hard hat, including some of the very latest innovative designs, ask questions and pass on any comments and suggestions.

  7. Hardness of metallic crystals

    Indian Academy of Sciences (India)

    Wuhui Li; Fengzhang Ren; Juanhua Su; Zhanhong Ma; Ke Cao; Baohong Tian

    2011-07-01

    This paper presents a new formula for calculating the hardness of metallic crystals, resulted from the research on the critical grain size with stable dislocations. The formula is = 6 /[(1 – )], where is the hardness, the coefficient, the shear modulus, the Poisson’s ratio, a function of the radius of an atom () and the electron density at the atom interface (). The formula will not only be used to testify the critical grain size with stable dislocations, but also play an important role in the understanding of mechanical properties of nanocrystalline metals.

  8. Hard exclusive QCD processes

    Energy Technology Data Exchange (ETDEWEB)

    Kugler, W.

    2007-01-15

    Hard exclusive processes in high energy electron proton scattering offer the opportunity to get access to a new generation of parton distributions, the so-called generalized parton distributions (GPDs). This functions provide more detailed informations about the structure of the nucleon than the usual PDFs obtained from DIS. In this work we present a detailed analysis of exclusive processes, especially of hard exclusive meson production. We investigated the influence of exclusive produced mesons on the semi-inclusive production of mesons at fixed target experiments like HERMES. Further we give a detailed analysis of higher order corrections (NLO) for the exclusive production of mesons in a very broad range of kinematics. (orig.)

  9. Effect of water hardness on the ability of water to rinse bacteria from the skin of processed broilers

    Science.gov (United States)

    The effect of water hardness on the ability of water to rinse bacteria from the skin of processed broiler chickens was examined. Artificial hard water with a total hardness of 200 ppm (very hard water) was prepared by dissolving calcium chloride (CaCl2) and magnesium chloride hexahydrate (MgCl2 •6H2...

  10. Simple screening method for copy number variations associated with physical features.

    Science.gov (United States)

    Ueki, Misuzu; Takeshita, Haruo; Fujihara, Junko; Kimura-Kataoka, Kaori; Iida, Reiko; Yasuda, Toshihiro

    2017-03-01

    Recent studies of copy number variations (CNVs) associated with physical features, such as body mass index, body height or bone length, have suggested that such CNVs could serve as markers in forensic cases involving unidentified individuals. However, the process of cataloging CNVs has been slow because of the cumbersome nature and low reliability of the procedures involved. Here we describe a simple quantitative real-time PCR (Q-PCR) method for screening of medicolegally useful CNVs, which does not require reference DNA with known copy number. The first step is to prepare a chimeric plasmid vector including one copy each of the single-copy gene-specific sequence as the internal standard, and the target CNV-specific sequence. To assess the validity of this new method, we analyzed CNVs in the LTBP1 and ETV6 gene regions, both of which are candidate CNVs associated with body height. The PCR efficiencies for the single-copy (reference) gene and the target CNV were similar, indicating that quantitation was reliable. Furthermore, simulated analysis of the LTBP1 CNV using mock samples prepared by mixing vectors in varying proportions showed that this analytical method allowed correct determination of the LTBP1 copy number. These results demonstrated that our simple method has considerable potential for screening of trait-related CNVs that would be useful for forensic casework. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. CSI: Hard Drive

    Science.gov (United States)

    Sturgeon, Julie

    2008-01-01

    Acting on information from students who reported seeing a classmate looking at inappropriate material on a school computer, school officials used forensics software to plunge the depths of the PC's hard drive, searching for evidence of improper activity. Images were found in a deleted Internet Explorer cache as well as deleted file space.…

  12. Hard Probes at ATLAS

    CERN Document Server

    Citron, Z; The ATLAS collaboration

    2014-01-01

    The ATLAS collaboration has measured several hard probe observables in Pb+Pb and p+Pb collisions at the LHC. These measurements include jets which show modification in the hot dense medium of heavy ion collisions as well as color neutral electro-weak bosons. Together, they elucidate the nature of heavy ion collisions.

  13. Rock-hard coatings

    NARCIS (Netherlands)

    Muller, M.

    2007-01-01

    Aircraft jet engines have to be able to withstand infernal conditions. Extreme heat and bitter cold tax coatings to the limit. Materials expert Dr Ir. Wim Sloof fits atoms together to develop rock-hard coatings. The latest invention in this field is known as ceramic matrix composites. Sloof has sign

  14. Budgeting in Hard Times.

    Science.gov (United States)

    Parrino, Frank M.

    2003-01-01

    Interviews with school board members and administrators produced a list of suggestions for balancing a budget in hard times. Among these are changing calendars and schedules to reduce heating and cooling costs; sharing personnel; rescheduling some extracurricular activities; and forming cooperative agreements with other districts. (MLF)

  15. Hard and Soft Governance

    DEFF Research Database (Denmark)

    Moos, Lejf

    2009-01-01

    The governance and leadership at transnational, national and school level seem to be converging into a number of isomorphic forms as we see a tendency towards substituting 'hard' forms of governance, that are legally binding, with 'soft' forms based on persuasion and advice. This article analyses...

  16. Running in Hard Times

    Science.gov (United States)

    Berry, John N., III

    2009-01-01

    Roberta Stevens and Kent Oliver are campaigning hard for the presidency of the American Library Association (ALA). Stevens is outreach projects and partnerships officer at the Library of Congress. Oliver is executive director of the Stark County District Library in Canton, Ohio. They have debated, discussed, and posted web sites, Facebook pages,…

  17. Hard times; Schwere Zeiten

    Energy Technology Data Exchange (ETDEWEB)

    Grunwald, Markus

    2012-10-02

    The prices of silicon and solar wafers keep dropping. According to market research specialist IMS research, this is the result of weak traditional solar markets and global overcapacities. While many manufacturers are facing hard times, big producers of silicon are continuing to expand.

  18. ACTA Technology Presents EPA with Patent Copy

    Science.gov (United States)

    US EPA SBIR awardee, ACTA Technology, presented James H. Johnson, Director of the US EPA National Center for Environmental Research, and April Richards, Program Manager of the US EPA's SBIR Program, with a copy of their Red Ribbon patent.

  19. Preservation Copying Endangered Historic Negative Collections

    DEFF Research Database (Denmark)

    Kejser, Ulla Bøgvad

    2008-01-01

    This article discusses preservation copying of unstable B&W nitrate and acetate still photographic negatives. It focuses on evaluating two different strategies for preserving the copies from a point of view of quality and cost-effectiveness. The evaluated strategies are preservation of the master...... by describing essential characteristics of negatives, which must be passed on to the copies, and the required metadata and technical imaging specifications. Next the paper discusses strategies for preservation and makes an analysis with the LIFE2 Costing Model. The paper concludes that the most beneficial...... and cost-effective preservation solution for large format negatives is to keep the preservation copies as digital files. However, it also acknowledges that it is important to revisit such strategies regularly to monitor changes in user expectations, technologies and costs....

  20. Copy number variation across European populations.

    Directory of Open Access Journals (Sweden)

    Wanting Chen

    Full Text Available Genome analysis provides a powerful approach to test for evidence of genetic variation within and between geographical regions and local populations. Copy number variants which comprise insertions, deletions and duplications of genomic sequence provide one such convenient and informative source. Here, we investigate copy number variants from genome wide scans of single nucleotide polymorphisms in three European population isolates, the island of Vis in Croatia, the islands of Orkney in Scotland and the South Tyrol in Italy. We show that whereas the overall copy number variant frequencies are similar between populations, their distribution is highly specific to the population of origin, a finding which is supported by evidence for increased kinship correlation for specific copy number variants within populations.

  1. Line copy presentation slides with Kodalith.

    Science.gov (United States)

    Kraushar, M F; Bailey, B A

    1978-08-01

    Line copy presentation slides with white letters on a blue background can be produced with a two-step process. The slides are more permanent than diazo slides, and the process is faster and less expensive.

  2. Preservation Copying Endangered Historic Negative Collections

    DEFF Research Database (Denmark)

    Kejser, Ulla Bøgvad

    2008-01-01

    This article discusses preservation copying of unstable B&W nitrate and acetate still photographic negatives. It focuses on evaluating two different strategies for preserving the copies from a point of view of quality and cost-effectiveness. The evaluated strategies are preservation of the master...... files in a digital repository and outputting the copies on film, which is preserved in a traditional storage facility. The issues are put into perspective by a case study completed at the Royal Library, where endangered nitrate negatives of unique national value have been digitized. The paper starts...... by describing essential characteristics of negatives, which must be passed on to the copies, and the required metadata and technical imaging specifications. Next the paper discusses strategies for preservation and makes an analysis with the LIFE2 Costing Model. The paper concludes that the most beneficial...

  3. Local Reasoning about a Copying Garbage Collector

    DEFF Research Database (Denmark)

    Torp-Smith, Noah; Birkedal, Lars; Reynolds, John C.

    2008-01-01

    We present a programming language, model, and logic appropriate for implementing and reasoning about a memory management system. We state semantically what is meant by correctness of a copying garbage collector, and employ a variant of the novel separation logics to formally specify partial...... correctness of Cheney’s copying garbage collector in our program logic. Finally, we prove that our implementation of Cheney’s algorithm meets its specification using the logic we have given and auxiliary variables. Udgivelsesdato: 2008...

  4. COPI is required for enterovirus 71 replication.

    Directory of Open Access Journals (Sweden)

    Jianmin Wang

    Full Text Available Enterovirus 71 (EV71, a member of the Picornaviridae family, is found in Asian countries where it causes a wide range of human diseases. No effective therapy is available for the treatment of these infections. Picornaviruses undergo RNA replication in association with membranes of infected cells. COPI and COPII have been shown to be involved in the formation of picornavirus-induced vesicles. Replication of several picornaviruses, including poliovirus and Echovirus 11 (EV11, is dependent on COPI or COPII. Here, we report that COPI, but not COPII, is required for EV71 replication. Replication of EV71 was inhibited by brefeldin A and golgicide A, inhibitors of COPI activity. Furthermore, we found EV71 2C protein interacted with COPI subunits by co-immunoprecipitation and GST pull-down assay, indicating that COPI coatomer might be directed to the viral replication complex through viral 2C protein. Additionally, because the pathway is conserved among different species of enteroviruses, it may represent a novel target for antiviral therapies.

  5. Interactive Data Integration through Smart Copy & Paste

    CERN Document Server

    Ives, Zachary; Minton, Steve; Jacob, Marie; Talukdar, Partha; Tuchinda, Rattapoom; Ambite, Jose Luis; Muslea, Maria; Gazen, Cenk

    2009-01-01

    In many scenarios, such as emergency response or ad hoc collaboration, it is critical to reduce the overhead in integrating data. Ideally, one could perform the entire process interactively under one unified interface: defining extractors and wrappers for sources, creating a mediated schema, and adding schema mappings ? while seeing how these impact the integrated view of the data, and refining the design accordingly. We propose a novel smart copy and paste (SCP) model and architecture for seamlessly combining the design-time and run-time aspects of data integration, and we describe an initial prototype, the CopyCat system. In CopyCat, the user does not need special tools for the different stages of integration: instead, the system watches as the user copies data from applications (including the Web browser) and pastes them into CopyCat?s spreadsheet-like workspace. CopyCat generalizes these actions and presents proposed auto-completions, each with an explanation in the form of provenance. The user provides f...

  6. A multilevel model to address batch effects in copy number estimation using SNP arrays.

    Science.gov (United States)

    Scharpf, Robert B; Ruczinski, Ingo; Carvalho, Benilton; Doan, Betty; Chakravarti, Aravinda; Irizarry, Rafael A

    2011-01-01

    Submicroscopic changes in chromosomal DNA copy number dosage are common and have been implicated in many heritable diseases and cancers. Recent high-throughput technologies have a resolution that permits the detection of segmental changes in DNA copy number that span thousands of base pairs in the genome. Genomewide association studies (GWAS) may simultaneously screen for copy number phenotype and single nucleotide polymorphism (SNP) phenotype associations as part of the analytic strategy. However, genomewide array analyses are particularly susceptible to batch effects as the logistics of preparing DNA and processing thousands of arrays often involves multiple laboratories and technicians, or changes over calendar time to the reagents and laboratory equipment. Failure to adjust for batch effects can lead to incorrect inference and requires inefficient post hoc quality control procedures to exclude regions that are associated with batch. Our work extends previous model-based approaches for copy number estimation by explicitly modeling batch and using shrinkage to improve locus-specific estimates of copy number uncertainty. Key features of this approach include the use of biallelic genotype calls from experimental data to estimate batch-specific and locus-specific parameters of background and signal without the requirement of training data. We illustrate these ideas using a study of bipolar disease and a study of chromosome 21 trisomy. The former has batch effects that dominate much of the observed variation in the quantile-normalized intensities, while the latter illustrates the robustness of our approach to a data set in which approximately 27% of the samples have altered copy number. Locus-specific estimates of copy number can be plotted on the copy number scale to investigate mosaicism and guide the choice of appropriate downstream approaches for smoothing the copy number as a function of physical position. The software is open source and implemented in the R

  7. Theory of hard photoproduction

    OpenAIRE

    Klasen, Michael

    2002-01-01

    The present theoretical knowledge about photons and hard photoproduction processes, i.e. the production of jets, light and heavy hadrons, quarkonia, and prompt photons in photon-photon and photon-hadron collisions, is reviewed. Virtual and polarized photons and prompt photon production in hadron collisions are also discussed. The most important leading and next-to-leading order QCD results are compiled in analytic form. A large variety of numerical predictions is compared to data from TRISTAN...

  8. SUPER HARD SURFACED POLYMERS

    Energy Technology Data Exchange (ETDEWEB)

    Mansur, Louis K [ORNL; Bhattacharya, R [UES, Incorporated, Dayton, OH; Blau, Peter Julian [ORNL; Clemons, Art [ORNL; Eberle, Cliff [ORNL; Evans, H B [UES, Incorporated, Dayton, OH; Janke, Christopher James [ORNL; Jolly, Brian C [ORNL; Lee, E H [Consultant, Milpitas, CA; Leonard, Keith J [ORNL; Trejo, Rosa M [ORNL; Rivard, John D [ORNL

    2010-01-01

    High energy ion beam surface treatments were applied to a selected group of polymers. Of the six materials in the present study, four were thermoplastics (polycarbonate, polyethylene, polyethylene terephthalate, and polystyrene) and two were thermosets (epoxy and polyimide). The particular epoxy evaluated in this work is one of the resins used in formulating fiber reinforced composites for military helicopter blades. Measures of mechanical properties of the near surface regions were obtained by nanoindentation hardness and pin on disk wear. Attempts were also made to measure erosion resistance by particle impact. All materials were hardness tested. Pristine materials were very soft, having values in the range of approximately 0.1 to 0.5 GPa. Ion beam treatment increased hardness by up to 50 times compared to untreated materials. For reference, all materials were hardened to values higher than those typical of stainless steels. Wear tests were carried out on three of the materials, PET, PI and epoxy. On the ion beam treated epoxy no wear could be detected, whereas the untreated material showed significant wear.

  9. Comparison of time-dependent changes in the surface hardness of different composite resins

    OpenAIRE

    Ozcan, Suat; Yikilgan, Ihsan; Uctasli, Mine Betul; Bala, Oya; Kurklu, Zeliha Gonca Bek

    2013-01-01

    Objective: The aim of this study was to evaluate the change in surface hardness of silorane-based composite resin (Filtek Silorane) in time and compare the results with the surface hardness of two methacrylate-based resins (Filtek Supreme and Majesty Posterior). Materials and Methods: From each composite material, 18 wheel-shaped samples (5-mm diameter and 2-mm depth) were prepared. Top and bottom surface hardness of these samples was measured using a Vicker's hardness tester. The samples wer...

  10. Identifying single copy orthologs in Metazoa.

    Directory of Open Access Journals (Sweden)

    Christopher J Creevey

    2011-12-01

    Full Text Available The identification of single copy (1-to-1 orthologs in any group of organisms is important for functional classification and phylogenetic studies. The Metazoa are no exception, but only recently has there been a wide-enough distribution of taxa with sufficiently high quality sequenced genomes to gain confidence in the wide-spread single copy status of a gene.Here, we present a phylogenetic approach for identifying overlooked single copy orthologs from multigene families and apply it to the Metazoa. Using 18 sequenced metazoan genomes of high quality we identified a robust set of 1,126 orthologous groups that have been retained in single copy since the last common ancestor of Metazoa. We found that the use of the phylogenetic procedure increased the number of single copy orthologs found by over a third more than standard taxon-count approaches. The orthologs represented a wide range of functional categories, expression profiles and levels of divergence.To demonstrate the value of our set of single copy orthologs, we used them to assess the completeness of 24 currently published metazoan genomes and 62 EST datasets. We found that the annotated genes in published genomes vary in coverage from 79% (Ciona intestinalis to 99.8% (human with an average of 92%, suggesting a value for the underlying error rate in genome annotation, and a strategy for identifying single copy orthologs in larger datasets. In contrast, the vast majority of EST datasets with no corresponding genome sequence available are largely under-sampled and probably do not accurately represent the actual genomic complement of the organisms from which they are derived.

  11. Decomposition of Parallel Copies with Duplication

    Directory of Open Access Journals (Sweden)

    G. N. Purohit

    2012-05-01

    Full Text Available SSA form is becoming more popular in the context of JIT compilation since it allows the compiler to perform important optimizations like common sub-expression elimination or constant propagation without the drawbacks of keeping huge data structures in memory or requiring a lot of computing power. The recent approach of SSA-based register allocation performs SSA elimination after register allocation. F. Bouchez et al. proposed parallel copy motion to prevent the splitting of edges when going out of colored SSA by moving the code that should be assigned to the edges to a more convenient place. Duplications in parallel copies pose some problems when moving them. In this paper an approach has been developed to decompose parallel copies so that duplications can be handled separately and parallel copies can be easily moved away without duplication. A simple and elegant application is moving duplicated copies out of critical edges. This is often beneficial compared to the alternative splitting the edge.

  12. Theory of hard photoproduction

    Energy Technology Data Exchange (ETDEWEB)

    Klasen, M. [Hamburg Univ. (Germany). 2. Inst. fuer Theoretische Physik

    2002-06-01

    The present theoretical knowledge about photons and hard photoproduction processes, i.e. the production of jets, light and heavy hadrons, quarkonia, and prompt photons in photon-photon and photon-hadron collisions, is reviewed. Virtual and polarized photons and prompt photon production in hadron collisions are also discussed. The most important leading and next-to-leading order QCD results are compiled in analytic form. A large variety of numerical predictions is compared to data from TRISTAN, LEP, and HERA and extended to future electron and muon colliders. The sources of all relevant results are collected in a rich bibliography. (orig.)

  13. Stone-hard concrete

    NARCIS (Netherlands)

    Wassink, J.

    2014-01-01

    A polymer prepared from waste water extends the useful life of concrete. It also appears to be suitable as a protective coating for offshore applications. Chemistry professor Stephen Picken predicts that this ‘alginate’ could become huge.

  14. The Energy of COPI for Budding Membranes

    Science.gov (United States)

    Thiam, Abdou Rachid; Pincet, Frédéric

    2015-01-01

    As a major actor of cellular trafficking, COPI coat proteins assemble on membranes and locally bend them to bud 60 nm-size coated particles. Budding requires the energy of the coat assembly to overcome the one necessary to deform the membrane which primarily depends on the bending modulus and surface tension, γ. Using a COPI-induced oil nanodroplet formation approach, we modulated the budding of nanodroplets using various amounts and types of surfactant. We found a Heaviside-like dependence between the budding efficiency and γ: budding was only dependent on γ and occurred beneath 1.3 mN/m. With the sole contribution of γ to the membrane deformation energy, we assessed that COPI supplies ~1500 kBT for budding particles from membranes, which is consistent with common membrane deformation energies. Our results highlight how a simple remodeling of the composition of membranes could mechanically modulate budding in cells. PMID:26218078

  15. Black holes and the double copy

    CERN Document Server

    Monteiro, Ricardo; White, Chris D

    2014-01-01

    Recently, a perturbative duality between gauge and gravity theories (the double copy) has been discovered, that is believed to hold to all loop orders. In this paper, we examine the relationship between classical solutions of non-Abelian gauge theory and gravity. We propose a general class of gauge theory solutions that double copy to gravity, namely those involving stationary Kerr-Schild metrics. The Schwarzschild and Kerr black holes (plus their higher-dimensional equivalents) emerge as special cases. We also discuss plane wave solutions. Furthermore, a recently examined double copy between the self-dual sectors of Yang-Mills theory and gravity can be reinterpreted using a momentum-space generalisation of the Kerr-Schild framework.

  16. CNVkit: Genome-Wide Copy Number Detection and Visualization from Targeted DNA Sequencing.

    Directory of Open Access Journals (Sweden)

    Eric Talevich

    2016-04-01

    Full Text Available Germline copy number variants (CNVs and somatic copy number alterations (SCNAs are of significant importance in syndromic conditions and cancer. Massively parallel sequencing is increasingly used to infer copy number information from variations in the read depth in sequencing data. However, this approach has limitations in the case of targeted re-sequencing, which leaves gaps in coverage between the regions chosen for enrichment and introduces biases related to the efficiency of target capture and library preparation. We present a method for copy number detection, implemented in the software package CNVkit, that uses both the targeted reads and the nonspecifically captured off-target reads to infer copy number evenly across the genome. This combination achieves both exon-level resolution in targeted regions and sufficient resolution in the larger intronic and intergenic regions to identify copy number changes. In particular, we successfully inferred copy number at equivalent to 100-kilobase resolution genome-wide from a platform targeting as few as 293 genes. After normalizing read counts to a pooled reference, we evaluated and corrected for three sources of bias that explain most of the extraneous variability in the sequencing read depth: GC content, target footprint size and spacing, and repetitive sequences. We compared the performance of CNVkit to copy number changes identified by array comparative genomic hybridization. We packaged the components of CNVkit so that it is straightforward to use and provides visualizations, detailed reporting of significant features, and export options for integration into existing analysis pipelines. CNVkit is freely available from https://github.com/etal/cnvkit.

  17. Microstructure and hardness of bovine enamel in roselle extract solution

    Science.gov (United States)

    Dame, M. T.; Noerdin, A.; Indrani, D. J.

    2017-08-01

    The aim of this study was to analyze the effect of roselle extract solution on the microstructure and hardness of bovine enamel. Ten bovine teeth and a 5% concentration of roselle extract solution were prepared. Immersions of each bovine tooth in roselle extract solution were conducted up to 60 minutes. The bovine enamel surface was characterized in hardness and microscopy. It was apparent that the initial hardness was 328 KHN, and after immersion in 15 and 60 min, the values decrease to 57.4 KHN and 11 KHN, respectively. Scanning electron microscopy (SEM) revealed changes in enamel rods after immersion in the roselle extract solution.

  18. WATER HARDNESS AS AN IMPORTANT PARAMETER OF PH

    Directory of Open Access Journals (Sweden)

    Žigmund Tóth

    2013-02-01

    Full Text Available Quality of final product is to great extent influenced by intermediate products that are formed during beer production. In addition quality of pH is one of the most important properties that forms suitable medium for activity of enzymes complexes that have crucial influence on character of produced wort. Moreover enzymes influence the yield of production process and quality of final product as well. Quality of boiling water and especially its hardness have crucial task in terms of keeping optimal qualitative parameters. Water hardness is given by amount of salts, mainly calcium and magnesium salts. It is expressed as absolute hardness which is given by sum of temporary (carbonate and permanent (noncarbonate hardness. In our work we solved the effect of total water hardness on final pH of various intermediate products. We used different water samples and we prepared variants of total hardness by stirring of unpurified water with distilled water thus we achieved various values of hardness. For comparison we prepared several brews with regard to combinations of unpurified water and distilled water. Higher pH of boiling water was caused due to higher water alkalinity that negatively affected enzyme complex present in used malt. Presence of hydrogenphosphates in used malt had high buffering ability and pH lowering ability. Such unfavorable result could be adjust by use of various additions of acidulates that would have in great extent influence on beer final price therefore boiling water adjustment seems to be the most acceptable approach.

  19. Low hardness EPDM/PP thermoplastic dynamic vulcanizates Ⅱ. Effect on micromorphology of preparation technological conditions%低硬度EPDM/PP热塑性动态硫化胶Ⅱ.制备工艺条件对微观相态结构的影响

    Institute of Scientific and Technical Information of China (English)

    吴崇刚; 朱玉俊; 孙亚娟; 冯予星; 张飞; 郭杰

    2001-01-01

    通过正交试验设计,研究了低硬度EPDM/PP共混型热塑性动态硫化胶的反应挤出动态硫化制备工艺,初步探讨了机筒温度、喂料螺杆驱动电压及主机螺杆转速等主要工艺因素对挤出物徽观相态结构的影响。%Through orthogonal experiment design,the preparation technology of reactive extrusion dy-namic vulcanization for low hardness EPDM/PPblend thermoplastic dynamic vulcanizates was stud-ied,and the effects on micromorphology of extrudedvulcanizates of such main technological factors asbarrel temperature,feed screw driven voltage andhost machine screw rotation rate were discussed.

  20. Locally resolved investigation of wedged Cu(In,Ga)Se{sub 2} films prepared by physical vapor deposition using hard X-ray photoelectron and X-ray fluorescence spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Calvet, Wolfram, E-mail: wolfram.calvet@helmholtz-berlin.de [Helmholtz-Zentrum Berlin, Hahn-Meitner-Platz 1, D-14109 Berlin (Germany); Ümsür, Bünyamin; Höpfner, Britta; Lauermann, Iver; Prietzel, Karsten; Kaufmann, Christan A.; Unold, Thomas [Helmholtz-Zentrum Berlin, Hahn-Meitner-Platz 1, D-14109 Berlin (Germany); Lux-Steiner, Martha C. [Helmholtz-Zentrum Berlin, Hahn-Meitner-Platz 1, D-14109 Berlin (Germany); Freie Universität Berlin, Department of Physics, Arnimallee 14, D-14195 Berlin (Germany)

    2015-05-01

    We have investigated a specially grown Cu(In,Ga)Se{sub 2} (CIGSe) absorber, which was deposited by co-evaporation of Cu, In, Ga, and Se using a modified three stage process. Prior to the growth, the molybdenum-coated glass substrate was covered by a bent shroud made from tantalum (Ta), leading to a wedged absorber structure with a width of about 2 mm where the film thickness varies from 0 to 2 μm. In this region of interest the thickness dependency of morphology, concentration ratios and electronic properties was studied with secondary electron microscopy (SEM), X-ray fluorescence (XRF) and hard X-ray photoelectron spectroscopy (HAXPES), probing the CIGSe sample along the thickness gradient. The evidence of the thickness gradient itself was proven with SEM measurements in cross section geometry. By using XRF it was found that with decreasing film thickness the Cu concentration decreases significantly. This finding was also verified by HAXPES measurements. Furthermore, an enrichment of Ga towards the Mo back contact was found using the same technique. Besides these results the formation of a molybdenum selenide (MoSe) phase was observed on the fully covered part of the Mo coated substrate indicating a high mobility of Se on Mo under the given temperature conditions of the modified three stage deposition process. - Highlights: • Growth of a CIGSe wedge • Application of HAXPES and XRF as local probing techniques • Good agreement with former studies • Wedged CIGSe structures can be used for further, locally resolved experiments.

  1. Teaching Ad Copy--I and II.

    Science.gov (United States)

    Welty, Ward; Vanden Bergh, Bruce G.

    1981-01-01

    Ward Welty notes that the standard advertising course could be improved by including a unit of study in rhetoric, especially Aristotelian rhetoric. Bruce Vanden Bergh reports on research on the differences in creating advertising copy for radio versus the visual media of magazines, newspapers, and television. (RL)

  2. 48 CFR 1401.105-3 - Copies.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Copies. 1401.105-3 Section... of the Interior, 1849 C Street (MS 2607-MIB), NW., Washington, DC 20240. Additional information on DOI may be obtained on the Internet at http://www.doi.gov/pam....

  3. 48 CFR 2901.105-3 - Copies.

    Science.gov (United States)

    2010-10-01

    ... information on DOL may be obtained on the Internet at www.dol.gov. Other DOL procurement policy documents... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Copies. 2901.105-3 Section 2901.105-3 Federal Acquisition Regulations System DEPARTMENT OF LABOR GENERAL DEPARTMENT OF...

  4. Teaching Ad Copy--I and II.

    Science.gov (United States)

    Welty, Ward; Vanden Bergh, Bruce G.

    1981-01-01

    Ward Welty notes that the standard advertising course could be improved by including a unit of study in rhetoric, especially Aristotelian rhetoric. Bruce Vanden Bergh reports on research on the differences in creating advertising copy for radio versus the visual media of magazines, newspapers, and television. (RL)

  5. Hard and Soft Governance

    DEFF Research Database (Denmark)

    Moos, Lejf

    2009-01-01

    and discusses governance forms at several levels. The first layer is the global: the methods of 'soft governance' that are being utilised by transnational agencies. The second layer is the national and local: the shift in national and local governance seen in many countries, but here demonstrated in the case......The governance and leadership at transnational, national and school level seem to be converging into a number of isomorphic forms as we see a tendency towards substituting 'hard' forms of governance, that are legally binding, with 'soft' forms based on persuasion and advice. This article analyses...... of Denmark, and finally the third layer: the leadership used in Danish schools. The use of 'soft governance' is shifting the focus of governance and leadership from decisions towards influence and power and thus shifting the focus of the processes from the decision-making itself towards more focus...

  6. Hard photoproduction at HERA

    Energy Technology Data Exchange (ETDEWEB)

    Klasen, M. [Laboratoire de Physique Subatomique et de Cosmologie, Universite Joseph Fourier / CNRS-IN2P3, 53 Avenue des Martyrs, F-38026 Grenoble (France)

    2007-07-01

    In view of possible photoproduction studies in ultra-peripheral heavy-ion collisions at the LHC, we briefly review the present theoretical understanding of photons and hard photoproduction processes at HERA, discussing the production of jets, light and heavy hadrons, quarkonia, and prompt photons. We address in particular the extraction of the strong coupling constant from photon structure function and inclusive jet measurements, the infrared safety and computing time of jet definitions, the sensitivity of di-jet cross sections on the parton densities in the photon, factorization breaking in diffractive di-jet production, the treatment of the heavy-quark mass in charm production, the relevance of the color-octet mechanism for quarkonium production, and isolation criteria for prompt photons. (author)

  7. Adaptive copy number evolution in malaria parasites.

    Directory of Open Access Journals (Sweden)

    Shalini Nair

    2008-10-01

    Full Text Available Copy number polymorphism (CNP is ubiquitous in eukaryotic genomes, but the degree to which this reflects the action of positive selection is poorly understood. The first gene in the Plasmodium folate biosynthesis pathway, GTP-cyclohydrolase I (gch1, shows extensive CNP. We provide compelling evidence that gch1 CNP is an adaptive consequence of selection by antifolate drugs, which target enzymes downstream in this pathway. (1 We compared gch1 CNP in parasites from Thailand (strong historical antifolate selection with those from neighboring Laos (weak antifolate selection. Two percent of chromosomes had amplified copy number in Laos, while 72% carried multiple (2-11 copies in Thailand, and differentiation exceeded that observed at 73 synonymous SNPs. (2 We found five amplicon types containing one to greater than six genes and spanning 1 to >11 kb, consistent with parallel evolution and strong selection for this gene amplification. gch1 was the only gene occurring in all amplicons suggesting that this locus is the target of selection. (3 We observed reduced microsatellite variation and increased linkage disequilibrium (LD in a 900-kb region flanking gch1 in parasites from Thailand, consistent with rapid recent spread of chromosomes carrying multiple copies of gch1. (4 We found that parasites bearing dhfr-164L, which causes high-level resistance to antifolate drugs, carry significantly (p = 0.00003 higher copy numbers of gch1 than parasites bearing 164I, indicating functional association between genes located on different chromosomes but linked in the same biochemical pathway. These results demonstrate that CNP at gch1 is adaptive and the associations with dhfr-164L strongly suggest a compensatory function. More generally, these data demonstrate how selection affects multiple enzymes in a single biochemical pathway, and suggest that investigation of structural variation may provide a fast-track to locating genes underlying adaptation.

  8. 2TB hard disk drive

    CERN Multimedia

    This particular object was used up until 2012 in the Data Centre. It slots into one of the Disk Server trays. Hard disks were invented in the 1950s. They started as large disks up to 20 inches in diameter holding just a few megabytes (link is external). They were originally called "fixed disks" or "Winchesters" (a code name used for a popular IBM product). They later became known as "hard disks" to distinguish them from "floppy disks (link is external)." Hard disks have a hard platter that holds the magnetic medium, as opposed to the flexible plastic film found in tapes and floppies.

  9. Parents welcome "hard-hitting" campaign.

    Science.gov (United States)

    1994-01-01

    The FPA (Family Planning Association)'s recent pilot campaign to encourage parents to talk to their children about sex has generated an excellent response rate. Funded by the Department of Health as part of "The health of the nation" efforts to reduce unplanned teenage pregnancies, the campaign centered on two radio advertisements. Aired during March in Greater London and North West England, the advertisements featured a free phone number from which people could obtain free copies of the booklet "Answering your child's questions," part of the FPA's "Growing Up" series. Nearly 7500 copies of the booklet were distributed in response to over 5000 requests--2500 rang in the first week alone. Most requests were from parents (69% mothers, 31% fathers) with one to three children aged between 7 and 13. Over 1000 requests were from parents with children under 7. Hundreds of schools, youth clubs, health professionals and voluntary organizations requested multiple booklets for use in their work. Research carried out to gauge public reaction showed overwhelming support for the campaign's message, demonstrating the immense need by parents for information in this area. "Answering your child's questions" was praised for being "open, direct and easy to follow." One parent said, "The booklet arms parents with the right way of putting information across." Parents described the advertisements as "hard-hitting" and "attention-grabbing." One listener commented: "They really stopped me in my tracks." FPA director Doreen Massey said: "The favorable reaction to the campaign is extremely encouraging. We are looking at ways to relay this pilot effort into a full-scale UK-wide campaign next year."

  10. Enhancing yields of low and single copy number plasmid DNAs from Escherichia coli cells.

    Science.gov (United States)

    Wood, Whitney N; Smith, Kyle D; Ream, Jennifer A; Kevin Lewis, L

    2017-02-01

    Many plasmids used for gene cloning and heterologous protein expression in Escherichia coli cells are low copy number or single copy number plasmids. The extraction of these types of plasmids from small bacterial cell cultures produces low DNA yields. In this study, we have quantitated yields of low copy and single copy number plasmid DNAs after growth of cells in four widely used broths (SB, SOC, TB, and 2xYT) and compared results to those obtained with LB, the most common E. coli cell growth medium. TB (terrific broth) consistently generated the greatest amount of plasmid DNA, in agreement with its ability to produce higher cell titers. The superiority of TB was primarily due to its high levels of yeast extract (24g/L) and was independent of glycerol, a unique component of this broth. Interestingly, simply preparing LB with similarly high levels of yeast extract (LB24 broth) resulted in plasmid yields that were equivalent to those of TB. By contrast, increasing ampicillin concentration to enhance plasmid retention did not improve plasmid DNA recovery. These experiments demonstrate that yields of low and single copy number plasmid DNAs from minipreps can be strongly enhanced using simple and inexpensive media. Copyright © 2016 Elsevier B.V. All rights reserved.

  11. Use of competitive PCR to assay copy number of repetitive elements in banana.

    Science.gov (United States)

    Baurens, F C; Noyer, J L; Lanaud, C; Lagoda, P J

    1996-11-27

    Banana is one of the most important subtropical fruit crops. Genetic improvement by traditional breeding strategies is difficult and better knowledge of genomic structure is needed. Repeated sequences are powerful markers for genetic fingerprinting. The method proposed here to determine the copy number of nuclear repetitive elements is based on competitive reverse transcription-polymerase chain reaction and can also be used for quantifying cytosolic sequences. The reliability of this method was investigated on crude preparations of total DNA. Variations due to the heterogeneity of crude DNA extracts showed that a single locus reference is needed for accurate quantification. A mapped microsatellite locus was used to normalize copy number measurements. Copy number assay of repetitive elements using this method clearly distinguishes between the two banana subspecies investigated: Musa acuminata spp. banskii and M. acuminata spp. malaccensis. Two repetitive sequence families, pMaCIR1115 and pA9-26, were assayed that cover up to 1% of the M. acuminata genome. Their copy number varied up to six fold between the two subspecies. Furthermore, sequence quantification showed that mitochondrial genomes are present in crude leaf-extracted banana DNA at up to 40 copies per cell.

  12. Influence of water hardness on the ability of water to rinse bacteria from the skin of processed broilers

    Science.gov (United States)

    Experiments were conducted to examine the effect of water hardness on the ability of water to rinse bacteria from the skin of processed broiler chickens. Very hard water (200 ppm total hardness) was prepared by dissolving 0.38 g calcium chloride (CaCl2) and 0.175 g magnesium chloride hexahydrate (Mg...

  13. Hard coal; Steinkohle

    Energy Technology Data Exchange (ETDEWEB)

    Loo, Kai van de; Sitte, Andreas-Peter [Gesamtverband Steinkohle e.V. (GVSt), Herne (Germany)

    2015-07-01

    International the coal market in 2014 was the first time in a long time in a period of stagnation. In Germany, the coal consumption decreased even significantly, mainly due to the decrease in power generation. Here the national energy transition has now been noticable affected negative for coal use. The political guidances can expect a further significant downward movement for the future. In the present phase-out process of the German hard coal industry with still three active mines there was in 2014 no decommissioning. But the next is at the end of 2015, and the plans for the time after mining have been continued. [German] International war der Markt fuer Steinkohle 2014 erstmals seit langem wieder von einer Stagnation gekennzeichnet. In Deutschland ging der Steinkohlenverbrauch sogar deutlich zurueck, vor allem wegen des Rueckgangs in der Stromerzeugung. Hier hat sich die nationale Energiewende nun spuerbar und fuer die Steinkohlennutzung negativ ausgewirkt. Die politischen Weichenstellungen lassen fuer die Zukunft eine weitere erhebliche Abwaertsbewegung erwarten. Bei dem im Auslaufprozess befindlichen deutschen Steinkohlenbergbau mit noch drei aktiven Bergwerken gab es 2014 keine Stilllegung. Doch die naechste steht zum Jahresende 2015 an, und die Planungen fuer die Zeit nach dem Bergbau sind fortgefuehrt worden.

  14. Chimpanzees copy dominant and knowledgeable individuals

    DEFF Research Database (Denmark)

    Kendal, Rachel; Hopper, Lydia M.; Whiten, Andrew

    2015-01-01

    Evolutionary theory predicts that natural selection will fashion cognitive biases to guide when, and from whom, individuals acquire social information, but the precise nature of these biases, especially in ecologically valid group contexts, remains unknown. We exposed four captive groups...... of chimpanzees (Pan troglodytes) to a novel extractive foraging device and, by fitting statistical models, isolated four simultaneously operating transmission biases. These include biases to copy (i) higher-ranking and (ii) expert individuals, and to copy others when (iii) uncertain or (iv) of low rank. High......-ranking individuals were relatively un-strategic in their use of acquired knowledge, which, combined with the bias for others to observe them, may explain reports that high innovation rates (in juveniles and subordinates) do not generate a correspondingly high frequency of traditions in chimpanzees. Given...

  15. [Create or copy... Which is the difference?].

    Science.gov (United States)

    López P, Ricardo

    2009-01-01

    Creating and copying are two different processes; we must not confuse creativity with plagiarism. However, this distinction is problematic, because there is no possibility of creating from scratch, this implies that any creative act necessarily arises from accumulative experience, inevitably producing a continuity between old and new. Even so it is necessary to establish clearly the difference between creating and copying. It is not desirable that a matter of such importance remains in the nebula or that the relationship between creativity and ethics is kept unaware. There are many cases of plagiarism, but this cannot be a consolation. There is no gain when the existence of a plagiarism is ignored or concealed and less when it is unjustified.

  16. Watermarking scar as an ultimate copy protection

    Energy Technology Data Exchange (ETDEWEB)

    Braci, Sofiane; Miraoui, Abdelkader; Delpha, Claude; Boyer, Remy, E-mail: sofiane.braci@lss.supelec.f, E-mail: Abdelkader.Miraoui@lss.supelec.f, E-mail: claude.delpha@lss.supelec.f, E-mail: remy.boyer@lss.supelec.f [University Paris-Sud 11, Laboratory of Signals and Systems, Supelec, 3 rue Joliot-Curie, 91192 Gif-sur-Yvette cedex (France)

    2010-02-01

    Strong and powerful attacks are able to make the watermark extraction impossible even if there is some watermarking. In this work, we call this residual information the scar and we use it to prove the existence of an attacked watermark. We evaluate the Scar by the mutual information between the embedded watermark and the attacked copies. It is well known that the mutual information between two random variables gives an evaluation of the shared information between the two variables. Thus, the attack can compromise the correct decoding by removing partially the watermarking information. However, it is possible to make the watermarking existence proof possible when the mutual information between the embedded message and the attacked copies is above a certain threshold. We propose a practical way to use the scar by measuring the correlation between the attacked watermark and the original one.

  17. Measuring the Hardness of Minerals

    Science.gov (United States)

    Bushby, Jessica

    2005-01-01

    The author discusses Moh's hardness scale, a comparative scale for minerals, whereby the softest mineral (talc) is placed at 1 and the hardest mineral (diamond) is placed at 10, with all other minerals ordered in between, according to their hardness. Development history of the scale is outlined, as well as a description of how the scale is used…

  18. Why All the Hard Work?

    Institute of Scientific and Technical Information of China (English)

    VALERIE; SARTOR

    2011-01-01

    The stereotype of the hard working Chinese has been around for a long time in the West. As early a 1894, Arthur Smith, a missionary who spent 54 years in China, wrote book introducing the hard-working Chinese people to Americans. In his book Chinese Characteristics, Smith wrote about the dili

  19. Phase behavior of hard particles

    NARCIS (Netherlands)

    Duijneveldt, J.S. van; Lekkerkerker, H.N.W.

    1995-01-01

    The phase behavior of hard particles and mixtures thereof is reviewed. Special attention is given to a lattice model consisting of hard hexagons and points on a triangular lattice. This model appears to have two disordered phases and an ordered phase.

  20. Melting of polydisperse hard disks

    NARCIS (Netherlands)

    Pronk, S.; Frenkel, D.

    2004-01-01

    The melting of a polydisperse hard-disk system is investigated by Monte Carlo simulations in the semigrand canonical ensemble. This is done in the context of possible continuous melting by a dislocation-unbinding mechanism, as an extension of the two-dimensional hard-disk melting problem. We find

  1. Melting of polydisperse hard disks

    NARCIS (Netherlands)

    Pronk, S.; Frenkel, D.

    2004-01-01

    The melting of a polydisperse hard-disk system is investigated by Monte Carlo simulations in the semigrand canonical ensemble. This is done in the context of possible continuous melting by a dislocation-unbinding mechanism, as an extension of the two-dimensional hard-disk melting problem. We find th

  2. Digital authentication with copy-detection patterns

    Science.gov (United States)

    Picard, Justin

    2004-06-01

    Technologies for making high-quality copies of documents are getting more available, cheaper, and more efficient. As a result, the counterfeiting business engenders huge losses, ranging to 5% to 8% of worldwide sales of brand products, and endangers the reputation and value of the brands themselves. Moreover, the growth of the Internet drives the business of counterfeited documents (fake IDs, university diplomas, checks, and so on), which can be bought easily and anonymously from hundreds of companies on the Web. The incredible progress of digital imaging equipment has put in question the very possibility of verifying the authenticity of documents: how can we discern genuine documents from seemingly "perfect" copies? This paper proposes a solution based on creating digital images with specific properties, called a Copy-detection patterns (CDP), that is printed on arbitrary documents, packages, etc. CDPs make an optimal use of an "information loss principle": every time an imae is printed or scanned, some information is lost about the original digital image. That principle applies even for the highest quality scanning, digital imaging, printing or photocopying equipment today, and will likely remain true for tomorrow. By measuring the amount of information contained in a scanned CDP, the CDP detector can take a decision on the authenticity of the document.

  3. 42 CFR 456.612 - Copies of reports.

    Science.gov (United States)

    2010-10-01

    ... Institutions for Mental Diseases § 456.612 Copies of reports. The agency must send a copy of each inspection... function, including, if inspection reports concern IMD's, the appropriate State mental health authorities....

  4. 19 CFR 133.42 - Infringing copies or phonorecords.

    Science.gov (United States)

    2010-04-01

    ...) Referral to the U.S. Attorney. In the event that phonorecords or copies of motion pictures arrive in the U... trafficking in counterfeit labels for phonorecords or copies of motion pictures or other audiovisual works...

  5. Conditionally amplifiable BACs: switching from single-copy to high-copy vectors and genomic clones.

    Science.gov (United States)

    Wild, Jadwiga; Hradecna, Zdenka; Szybalski, Waclaw

    2002-09-01

    The widely used, very-low-copy BAC (bacterial artificial chromosome) vectors are the mainstay of present genomic research. The principal advantage of BACs is the high stability of inserted clones, but an important disadvantage is the low yield of DNA, both for vectors alone and when carrying genomic inserts. We describe here a novel class of single-copy/high-copy (SC/HC) pBAC/oriV vectors that retain all the advantages of low-copy BAC vectors, but are endowed with a conditional and tightly controlled oriV/TrfA amplification system that allows: (1) a yield of ~100 copies of the vector per host cell when conditionally induced with L-arabinose, and (2) analogous DNA amplification (only upon induction and with copy number depending on the insert size) of pBAC/oriV clones carrying >100-kb inserts. Amplifiable clones and libraries facilitate high-throughput DNA sequencing and other applications requiring HC plasmid DNA. To turn on DNA amplification, which is driven by the oriV origin of replication, we used copy-up mutations in the gene trfA whose expression was very tightly controlled by the araC-P(araBAD) promoter/regulator system. This system is inducible by L-arabinose, and could be further regulated by glucose and fucose. Amplification of DNA upon induction with L-arabinose and its modulation by glucose are robust and reliable. Furthermore, we discovered that addition of 0.2% D-glucose to the growth medium helped toward the objective of obtaining a real SC state for all BAC systems, thus enhancing the stability of their maintenance, which became equivalent to cloning into the host chromosome

  6. 33 CFR 88.05 - Copy of rules.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Copy of rules. 88.05 Section 88... RULES ANNEX V: PILOT RULES § 88.05 Copy of rules. The operator of each self-propelled vessel 12 meters or more in length shall carry on board and maintain for ready reference a copy of the Inland...

  7. 27 CFR 478.95 - Certified copy of license.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Certified copy of license... Conduct of Business § 478.95 Certified copy of license. The license furnished to each person licensed... the licensee desires an additional copy of the license for certification (instead of making a...

  8. 47 CFR 95.673 - Copy of rules.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Copy of rules. 95.673 Section 95.673... SERVICES Technical Regulations Additional Certification Requirements for Cb Transmitters § 95.673 Copy of rules. A copy of part 95, subpart D, of the FCC Rules, current at the time of packing of the transmitter...

  9. 40 CFR 374.5 - Copy of complaint.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 27 2010-07-01 2010-07-01 false Copy of complaint. 374.5 Section 374.5... COMMUNITY RIGHT-TO-KNOW PROGRAMS PRIOR NOTICE OF CITIZEN SUITS § 374.5 Copy of complaint. At the time of filing an action under this Act, the plaintiff must provide a copy of the complaint to the Attorney...

  10. Optimal copying of entangled two-qubit states

    CERN Document Server

    Novotny, J; Jex, I

    2004-01-01

    We investigate the problem of copying pure two-qubit states of a given degree of entanglement in an optimal way. Completely positive covariant quantum operations are constructed which maximize the fidelity of the output states with respect to two separable copies. These optimal copying processes hint at the intricate relationship between fundamental laws of quantum theory and entanglement.

  11. 27 CFR 22.165 - Photographic copies of records.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Photographic copies of records. 22.165 Section 22.165 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE... Transactions § 22.165 Photographic copies of records. (a) General. Permittees may record, copy, or...

  12. 27 CFR 19.725 - Photographic copies of records.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Photographic copies of records. 19.725 Section 19.725 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE... Photographic copies of records. (a) Application. Proprietors who desire to record, copy or reproduce...

  13. 27 CFR 31.192 - Photographic copies of records.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Photographic copies of records. 31.192 Section 31.192 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE... Records and Files § 31.192 Photographic copies of records. (a) General. Dealers may record, copy,...

  14. 27 CFR 18.64 - Photographic copies of records.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Photographic copies of records. 18.64 Section 18.64 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE... Reports § 18.64 Photographic copies of records. Proprietors may record, copy, or reproduce...

  15. 27 CFR 20.268 - Photographic copies of records.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Photographic copies of records. 20.268 Section 20.268 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE... Reports § 20.268 Photographic copies of records. (a) General. Permittees may record, copy, or...

  16. Effect of homogenization process on the hardness of Zn–Al–Cu alloys

    Institute of Scientific and Technical Information of China (English)

    Jose D. Villegas-Cardenas; Maribel L. Saucedo-Mu?oz; Victor M. Lopez-Hirata; Antonio De Ita-De la Torre; Erika O. Avila-Davila; Jorge Luis Gonzalez-Velazquez

    2015-01-01

    The effect of a homogenizing treatment on the hardness of as-cast Zn–Al–Cu alloys was investigated. Eight alloy compositions were prepared and homogenized at 350 ℃ for 180 h, and their Rockwell "B" hardness was subsequently measured. All the specimens were analyzed by X-ray diffraction and metallographically prepared for observation by optical microscopy and scanning electron microscopy. The results of the present work indicated that the hardness of both alloys (as-cast and homogenized) increased with increasing Al and Cu contents; this increased hardness is likely related to the presence of theθandτ′ phases. A regression equation was obtained to determine the hardness of the homogenized alloys as a function of their chemical composition and processing parameters, such as homogenization time and tem-perature, used in their preparation.

  17. Systematic hardness measurements on single crystals and polycrystalline blanks of cesium halides

    Indian Academy of Sciences (India)

    D B Sirdeshmukh; P Geeta Krishna; K G Subhadra

    2002-06-01

    Vickers and knoop hardness measurements were carried out on CsBr and CsI single crystals. Polycrystalline blanks of CsCl, CsBr and CsI were prepared by melting and characterized by X-ray diffraction. Vickers hardness measurements were carried out on these blanks. The hardness values were correlated with the lattice constant and the Schottky defect formation energy.

  18. Photon technology. Hard photon technology; Photon technology. Hard photon gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Research results of hard photon technology have been summarized as a part of novel technology development highly utilizing the quantum nature of photon. Hard photon technology refers to photon beam technologies which use photon in the 0.1 to 200 nm wavelength region. Hard photon has not been used in industry due to the lack of suitable photon sources and optical devices. However, hard photon in this wavelength region is expected to bring about innovations in such areas as ultrafine processing and material synthesis due to its atom selective reaction, inner shell excitation reaction, and spatially high resolution. Then, technological themes and possibility have been surveyed. Although there are principle proposes and their verification of individual technologies for the technologies of hard photon generation, regulation and utilization, they are still far from the practical applications. For the photon source technology, the laser diode pumped driver laser technology, laser plasma photon source technology, synchrotron radiation photon source technology, and vacuum ultraviolet photon source technology are presented. For the optical device technology, the multi-layer film technology for beam mirrors and the non-spherical lens processing technology are introduced. Also are described the reduction lithography technology, hard photon excitation process, and methods of analysis and measurement. 430 refs., 165 figs., 23 tabs.

  19. Partnering, Collaborating, and Moving Ahead: Transition for Deaf and Hard of Hearing Students in Minnesota

    Science.gov (United States)

    Knopf, Elise; Cashman-Bakken, Mary

    2016-01-01

    Minnesota leaders have worked hard to provide educational opportunities and employment services for people who are deaf or hard of hearing. The timely formation of pepnet 2 helped shape Minnesota's State Transition Team to "better prepare teachers, families, and students for transition from high school to independent living, employment,…

  20. Stolen and lost copies of Vesalius's Fabrica.

    Science.gov (United States)

    Steeno, Omer; Biesbrouck, Maurits

    2012-01-01

    Thefts and losses of precious books are not rare. Here we report several incidents concerning vesalius's Fabrica: the fire of the University Library of Leuven in Belgium, the fate of the collection of the Leopoldina Library of Halle in Germany, the thefts from the Crerar Library in Chicago and in Christ Church College in Oxford, the disappearance of an exceptionally beautiful 'royal' copy from the Castle of Argenteuil (Belgium), and other Fabrica's missing at the Franeker Library in the Netherlands and at the Library of oradea in West Romania. Finally the means of protecting precious book collections are discussed in short as well as the importance of book identification.

  1. Getting DNA copy numbers without control samples

    Directory of Open Access Journals (Sweden)

    Ortiz-Estevez Maria

    2012-08-01

    Full Text Available Abstract Background The selection of the reference to scale the data in a copy number analysis has paramount importance to achieve accurate estimates. Usually this reference is generated using control samples included in the study. However, these control samples are not always available and in these cases, an artificial reference must be created. A proper generation of this signal is crucial in terms of both noise and bias. We propose NSA (Normality Search Algorithm, a scaling method that works with and without control samples. It is based on the assumption that genomic regions enriched in SNPs with identical copy numbers in both alleles are likely to be normal. These normal regions are predicted for each sample individually and used to calculate the final reference signal. NSA can be applied to any CN data regardless the microarray technology and preprocessing method. It also finds an optimal weighting of the samples minimizing possible batch effects. Results Five human datasets (a subset of HapMap samples, Glioblastoma Multiforme (GBM, Ovarian, Prostate and Lung Cancer experiments have been analyzed. It is shown that using only tumoral samples, NSA is able to remove the bias in the copy number estimation, to reduce the noise and therefore, to increase the ability to detect copy number aberrations (CNAs. These improvements allow NSA to also detect recurrent aberrations more accurately than other state of the art methods. Conclusions NSA provides a robust and accurate reference for scaling probe signals data to CN values without the need of control samples. It minimizes the problems of bias, noise and batch effects in the estimation of CNs. Therefore, NSA scaling approach helps to better detect recurrent CNAs than current methods. The automatic selection of references makes it useful to perform bulk analysis of many GEO or ArrayExpress experiments without the need of developing a parser to find the normal samples or possible batches within the

  2. Unified approach to hard diffraction

    CERN Document Server

    Peschanski, R

    2001-01-01

    Using a combination of S-Matrix and perturbative QCD properties in the small x_{Bj} regime, we propose a formulation of hard diffraction unifying the partonic (Ingelman-Schlein) Pomeron, Soft Colour Interaction and QCD dipole descriptions.

  3. Ribosomal DNA copy number loss and sequence variation in cancer.

    Science.gov (United States)

    Xu, Baoshan; Li, Hua; Perry, John M; Singh, Vijay Pratap; Unruh, Jay; Yu, Zulin; Zakari, Musinu; McDowell, William; Li, Linheng; Gerton, Jennifer L

    2017-06-01

    Ribosomal DNA is one of the most variable regions in the human genome with respect to copy number. Despite the importance of rDNA for cellular function, we know virtually nothing about what governs its copy number, stability, and sequence in the mammalian genome due to challenges associated with mapping and analysis. We applied computational and droplet digital PCR approaches to measure rDNA copy number in normal and cancer states in human and mouse genomes. We find that copy number and sequence can change in cancer genomes. Counterintuitively, human cancer genomes show a loss of copies, accompanied by global copy number co-variation. The sequence can also be more variable in the cancer genome. Cancer genomes with lower copies have mutational evidence of mTOR hyperactivity. The PTEN phosphatase is a tumor suppressor that is critical for genome stability and a negative regulator of the mTOR kinase pathway. Surprisingly, but consistent with the human cancer genomes, hematopoietic cancer stem cells from a Pten-/- mouse model for leukemia have lower rDNA copy number than normal tissue, despite increased proliferation, rRNA production, and protein synthesis. Loss of copies occurs early and is associated with hypersensitivity to DNA damage. Therefore, copy loss is a recurrent feature in cancers associated with mTOR activation. Ribosomal DNA copy number may be a simple and useful indicator of whether a cancer will be sensitive to DNA damaging treatments.

  4. Hard nanocomposite Zr-Y-N coatings, correlation between hardness and structure

    Energy Technology Data Exchange (ETDEWEB)

    Musil, J.; Polakova, H. [Univ. of West Bohemia, Plzen (Czech Republic). Dept. of Phys.

    2000-05-01

    The article reports on structure and mechanical properties of Zr-Y-N nanocomposite films containing two immiscible elements (Zr,Y) as metals. Films were prepared by d.c.-reactive magnetron sputtering of alloyed targets ZrY (80/20 at.%) and ZrY (93/7 at.%) in a mixture of Ar+N{sub 2} using round planar unbalanced magnetrons of diameter 100 mm. It was shown that: (i) there is a strong correlation between the structure of the film and its hardness, H; (ii) the film structure can be controlled with the interlayer inserted between the substrate and the Zr-Y-N film; and (iii) the film hardness depends on the ratio N/(Zr+Y) in the film and the crystallographic orientation of ZrN grains. Superhard nanocomposite films with hardness greater than 40 GPa were prepared. These films are characterized by (i) the X-ray reflection from ZrN(200) grains and no reflection from the second phase containing Y; and (ii) the ratio N/(Zr+Y){approx}1. Also, it was found that the incorporation of nitrogen into the pure ZrY alloy film results in dramatic changes of its mechanical properties. The Zr-Y-N film can be very hard (up to 47 GPa), exhibits the high elastic recovery (W{sub e} up to 83%) and the high resistance to plastic deformation [H{sup 3}/E*{sup 2} up to approx. 0.75, where E*=E/(1-{nu}{sup 2}), E is the Young's modulus and {nu} is the Poisson's ratio]. On the contrary, the ZrY alloy film is soft (H{approx}6 GPa) and exhibits a low elastic recovery (W{sub e}=32%). (orig.)

  5. Identification of chloroquine resistance Pfcrt-K76T and determination of Pfmdr1-N86Y copy number by SYBR Green I qPCR

    Institute of Scientific and Technical Information of China (English)

    Addimas; Tajebe; Mulugeta; Aemero; Kimani; Francis; Gabriel; Magoma

    2015-01-01

    Objective:To identify prevalence of chloroquine resistance point mutation at(Pfcrt,K76T)and(Pfindr1.N86Y) copy number variation.Methods:SYBR Green I based real time PCR was used.One hundred and thirty-three samples were analyzed for(Pfcrt,K76T) and(Pfmdr1.N86Y) copy number from dried blood spot.Parasite DNA was extracted using high pure DNA preparation kit.The amplification of DNA was done by using AccuPower 2* GreenStar ’’ qPCR Master mix.For quantification purpose a new primer pair was designed for 178 base pair template from complete genome sequence of Plasmodium falciparum strain 3D7 at NCBI.Absolute quantification method was used to determine the Pfmdr1-N86 Y copy number variations.Standard curve was built from strain3D7 gDNA since it has single copy of Pfindr1 per haploid genome.The known positive controls with single and multi-copy number of Pfindr1 gene were included in each experiment.The copy number ratio of the samples to the standard calibrator was made to obtain the fold difference among the samples with respect to copy number variation.Results:Out of 133 samples 73(54.89%) were confirmed as mutant(Pfcrt,76T) and the remaining 60(45.11%) were genotyped as wild type(Pfcrt,K76).The(Pfindr1.N86Y) copy number variation was determined for 133 clinical samples.Out of these samples 61(45.86%)had single copy and the remaining 72(54.14%) had multi-copy numbers higher than 1.5 copies per genome.Thirty-four(25.56%) multi-copies were between 1.5 and 2.5 copies per genome while 38(28.57%) were more than 2.5 copies per genome.The minimum and maximum copies per genome were 0.474 and 4.741.respectively.Conclusions:The study showed high prevalence level and fixation of Pfcrt.76 T mutation after chloroquine withdrawal.The prevalence of Pfindr1 copy number variant suggested that the presence of modulating factor for emergence of Plasmodium falciparum strains with higher copy numbers.However,the prevalence level was not statistically significant.

  6. Demonstration of digital radiographs by means of ink jet-printed paper copies: pilot study.

    Science.gov (United States)

    Kirkhorn, T; Kehler, M; Nilsson, J; Lyttkens, K; Andersson, B; Holmer, N G

    1992-11-01

    Different digital medical images have been printed on paper with a continuous ink jet printer, and the quality has been evaluated. The emphasis has been on digital chest radiographs from a computed radiography system. The ink jet printing technique is described as well as the handling of the image data from image source to printer. Different versions of paper prints and viewing conditions were compared to find the optimum alternative. The evaluation has been performed to maximize the quality of the paper images to make them conform with the corresponding film prints and monitor images as much as possible. The continuous ink jet technique offers high-quality prints on paper at a considerably lower cost per copy compared with the cost of a film print. With a future switch-over from diagnosing of digital images on film to diagnosing them on monitors, hard copies for demonstration purposes will occasionally be needed. This need can be filled by ink jet-printed paper copies.

  7. Identification of copy number variants in horses

    KAUST Repository

    Doan, R.

    2012-03-01

    Copy number variants (CNVs) represent a substantial source of genetic variation in mammals. However, the occurrence of CNVs in horses and their subsequent impact on phenotypic variation is unknown. We performed a study to identify CNVs in 16 horses representing 15 distinct breeds (Equus caballus) and an individual gray donkey (Equus asinus) using a whole-exome tiling array and the array comparative genomic hybridization methodology. We identified 2368 CNVs ranging in size from 197 bp to 3.5 Mb. Merging identical CNVs from each animal yielded 775 CNV regions (CNVRs), involving 1707 protein- and RNA-coding genes. The number of CNVs per animal ranged from 55 to 347, with median and mean sizes of CNVs of 5.3 kb and 99.4 kb, respectively. Approximately 6% of the genes investigated were affected by a CNV. Biological process enrichment analysis indicated CNVs primarily affected genes involved in sensory perception, signal transduction, and metabolism. CNVs also were identified in genes regulating blood group antigens, coat color, fecundity, lactation, keratin formation, neuronal homeostasis, and height in other species. Collectively, these data are the first report of copy number variation in horses and suggest that CNVs are common in the horse genome and may modulate biological processes underlying different traits observed among horses and horse breeds.

  8. Quantum Copy-Protection and Quantum Money

    CERN Document Server

    Aaronson, Scott

    2011-01-01

    Forty years ago, Wiesner proposed using quantum states to create money that is physically impossible to counterfeit, something that cannot be done in the classical world. However, Wiesner's scheme required a central bank to verify the money, and the question of whether there can be unclonable quantum money that anyone can verify has remained open since. One can also ask a related question, which seems to be new: can quantum states be used as copy-protected programs, which let the user evaluate some function f, but not create more programs for f? This paper tackles both questions using the arsenal of modern computational complexity. Our main result is that there exist quantum oracles relative to which publicly-verifiable quantum money is possible, and any family of functions that cannot be efficiently learned from its input-output behavior can be quantumly copy-protected. This provides the first formal evidence that these tasks are achievable. The technical core of our result is a "Complexity-Theoretic No-Clon...

  9. Hard carbon nitride and method for preparing same

    Science.gov (United States)

    Haller, E.E.; Cohen, M.L.; Hansen, W.L.

    1992-05-05

    Novel crystalline [alpha](silicon nitride-like)-carbon nitride and [beta](silicon nitride-like)-carbon nitride are formed by sputtering carbon in the presence of a nitrogen atmosphere onto a single crystal germanium or silicon, respectively, substrate. 1 figure.

  10. Influence of alloy ingredients on mechanical properties of ternary boride hard alloy clad materials

    Institute of Scientific and Technical Information of China (English)

    LIU Fu-tian; SONG Shi-xue; YANG Jun-ru; HUANG Wei-ling; HUANG Chuan-zhen; CHENG Xin; LI Zhao-qian

    2004-01-01

    Using Mo, B-Fe alloy and Fe powders as raw materials, and adding C, Cr and Ni ingredients, respectively, or C, Cr and Ni mixed powders, ternary boride hard alloy clad materials was prepared on Q235 steel substrate by means of in-situ reaction and vacuum liquid phase sintering technology. The influence of alloy ingredients on the mechanical properties of ternary boride hard alloy clad materials was investigated. The results indicate that a mixture of 0.8% C, 5% Cr and 2% Ni ingredients gives a ternary boride hard alloy clad material with optimal mechanical properties, such as high transverse rupture strength, high hardness and good wear resistance.

  11. NANOCOMPOSITE COATINGS WITH ENHANCED HARDNESS

    Institute of Scientific and Technical Information of China (English)

    J. Musil

    2005-01-01

    The article reviews the present state of the art in the magnetron sputtering of hart and superhard nanocomposite coatings. It is shown that there are (1) two groups of hard and superhard nanocomposites: (i) nc-MN/hard phase and (ii) nc-MN/soft phase, (2) three possible origins of the enhanced hardness: (i) dislocation-dominated plastic deformation, (ii) cohesive forces between atoms and (iii) nanostructure of materials, and (3) huge differences in the microstructure of single- and two-phase films. A main attention is devoted to the formation of nanocrystalline and/or X-ray amorphous films. Such films are created in a vicinity of transitions between (i)crystalline and amorphous phases, (ii) two crystalline phases of different chemical composition or (iii) two different preferred orientations of grains of the sane material from which the coating is composed. The existence of the last transition makes it possible to explain the enhanced hardness in single-phase films. The thermal stability and oxidation resistance of hard nanocomposite films is also shortly discussed.

  12. Infant Formula - Buying, Preparing, Storing, and Feeding

    Science.gov (United States)

    ... 000806.htm Infant Formula – Buying, Preparing, Storing, and Feeding To use the sharing features on this page, ... brush to get at hard-to-reach places. Feeding Formula to Baby Here is a guide to ...

  13. Copy number variation in the bovine genome

    DEFF Research Database (Denmark)

    Fadista, João; Thomsen, Bo; Holm, Lars-Erik;

    2010-01-01

    to genetic variation in cattle. Results We designed and used a set of NimbleGen CGH arrays that tile across the assayable portion of the cattle genome with approximately 6.3 million probes, at a median probe spacing of 301 bp. This study reports the highest resolution map of copy number variation...... in the cattle genome, with 304 CNV regions (CNVRs) being identified among the genomes of 20 bovine samples from 4 dairy and beef breeds. The CNVRs identified covered 0.68% (22 Mb) of the genome, and ranged in size from 1.7 to 2,031 kb (median size 16.7 kb). About 20% of the CNVs co-localized with segmental...

  14. The Double Copy Structure of Soft Gravitons

    CERN Document Server

    Vera, Agustin Sabio

    2014-01-01

    The subleading corrections to factorization theorems for soft bremsstrahlung in nonabelian gauge theories and gravity are investigated. Building on recent results, we write the action of the angular momentum operators on scattering amplitudes as derivatives with respect to the Mandelstam invariants to uncover a double copy structure in the contribution of the soft graviton to the amplitude, both in the leading term and the first correction. Using our approach, we study Gribov's theorem as extended to nonabelian gauge theories and gravity by Lipatov, and find that subleading corrections can be obtained from those to Low's theorem by dropping the terms with derivatives with respect to the center-of-mass energy, which are suppressed at high energies. In this case, the emitted gravitons are not necessarily soft.

  15. Double-copy constructions and unitarity cuts

    Science.gov (United States)

    Bern, Zvi; Davies, Scott; Nohle, Josh

    2016-05-01

    The duality between color and kinematics enables the construction of multiloop gravity integrands directly from corresponding gauge-theory integrands. This has led to new nontrivial insights into the structure of gravity theories, including the discovery of enhanced ultraviolet cancellations. To continue to gain deeper understandings and probe these new properties, it is crucial to further improve techniques for constructing multiloop gravity integrands. In this paper, we show by example how one can alleviate difficulties encountered at the multiloop level by relaxing the color-kinematics duality conditions to hold manifestly only on unitarity cuts instead of globally on loop integrands. As an example, we use a minimal Ansatz to construct an integrand for the two-loop four-point nonsupersymmetric pure Yang-Mills amplitude in D dimensions that is compatible with these relaxed color-kinematics duality constraints. We then immediately obtain a corresponding gravity integrand through the double-copy procedure. Comments on ultraviolet divergences are also included.

  16. Double-Copy Constructions and Unitarity Cuts

    CERN Document Server

    Bern, Zvi; Nohle, Josh

    2016-01-01

    The duality between color and kinematics enables the construction of multiloop gravity integrands directly from corresponding gauge-theory integrands. This has led to new nontrivial insights into the structure of gravity theories, including the discovery of enhanced ultraviolet cancellations. To continue to gain deeper understandings and probe these new properties, it is crucial to further improve techniques for constructing multiloop gravity integrands. In this paper, we show by example how one can alleviate difficulties encountered at the multiloop level by relaxing the color-kinematics duality conditions to hold manifestly only on unitarity cuts instead of globally on loop integrands. As an example, we use a minimal ansatz to construct an integrand for the two-loop four-point nonsupersymmetric pure Yang-Mills amplitude in $D$ dimensions that is compatible with these relaxed color-kinematics duality constraints. We then immediately obtain a corresponding gravity integrand through the double-copy procedure. ...

  17. Comparing Android Applications to Find Copying

    Directory of Open Access Journals (Sweden)

    Larry Melling

    2012-03-01

    Full Text Available The Android smartphone operating system includes a Java mobile development platform that provides for rapid development and deployment of a wide variety of applications. The open nature of the platform means that reverse engineering of applications is relatively easy, and many developers are concerned as applications similar to their own show up in the Android marketplace and want to know if these applications are pirated. Fortunately, the same characteristics that make an Android application easy to reverse engineer and copy also provide opportunities for Android developers to compare downloaded applications to their own. This paper describes the process for comparing a developer’s application with a downloaded application and defines an identifiability metric to quantify the degree to which an application can be identified by its bytecode.

  18. Copy-move forgery detection in digital image

    Science.gov (United States)

    Alamro, Loai; Yusoff, Nooraini

    2016-08-01

    Copy-move is considered as one of the most popular kind of digital image tempering, in which one or more parts of a digital image are copied and pasted into different locations. Geometric transformation is among the major challenges in detecting copy-move forgery of a digital image. In such forgery, the copied and moved parts of a forged image are either rotated or/and re-scaled. Hence, in this study we propose a combination of Discrete Wavelet Transform (DWT) and Speeded Up Robust Features (SURF) to detect a copy-move activity. The experiments results prove that the proposed method is superior with overall accuracy 95%. The copy-move attacks in digital image has been successfully detected and the method is also can detect the fraud parts exposed to rotation and scaling issue.

  19. Characterization of an inducible promoter in different DNA copy number conditions.

    Science.gov (United States)

    Zucca, Susanna; Pasotti, Lorenzo; Mazzini, Giuliano; De Angelis, Maria Gabriella Cusella; Magni, Paolo

    2012-03-28

    The bottom-up programming of living organisms to implement novel user-defined biological capabilities is one of the main goals of synthetic biology. Currently, a predominant problem connected with the construction of even simple synthetic biological systems is the unpredictability of the genetic circuitry when assembled and incorporated in living cells. Copy number, transcriptional/translational demand and toxicity of the DNA-encoded functions are some of the major factors which may lead to cell overburdening and thus to nonlinear effects on system output. It is important to disclose the linearity working boundaries of engineered biological systems when dealing with such phenomena. The output of an N-3-oxohexanoyl-L-homoserine lactone (HSL)-inducible RFP-expressing device was studied in Escherichia coli in different copy number contexts, ranging from 1 copy per cell (integrated in the genome) to hundreds (via multicopy plasmids). The system is composed by a luxR constitutive expression cassette and a RFP gene regulated by the luxI promoter, which is activated by the HSL-LuxR complex. System output, in terms of promoter activity as a function of HSL concentration, was assessed relative to the one of a reference promoter in identical conditions by using the Relative Promoter Units (RPU) approach. Nonlinear effects were observed in the maximum activity, which is identical in single and low copy conditions, while it decreases for higher copy number conditions. In order to properly compare the luxI promoter strength among all the conditions, a mathematical modeling approach was used to relate the promoter activity to the estimated HSL-LuxR complex concentration, which is the actual activator of transcription. During model fitting, a correlation between the copy number and the dissociation constant of HSL-LuxR complex and luxI promoter was observed. Even in a simple inducible system, nonlinear effects are observed and non-trivial data processing is necessary to fully

  20. The standardised copy of pentagons test

    Directory of Open Access Journals (Sweden)

    Terzoglou Vassiliki A

    2011-04-01

    Full Text Available Abstract Background The 'double-diamond copy' task is a simple paper and pencil test part of the Bender-Gestalt Test and the Mini Mental State Examination (MMSE. Although it is a widely used test, its method of scoring is crude and its psychometric properties are not adequately known. The aim of the present study was to develop a sensitive and reliable method of administration and scoring. Methods The study sample included 93 normal control subjects (53 women and 40 men aged 35.87 ± 12.62 and 127 patients suffering from schizophrenia (54 women and 73 men aged 34.07 ± 9.83. Results The scoring method was based on the frequencies of responses of healthy controls and proved to be relatively reliable with Cronbach's α equal to 0.61, test-retest correlation coefficient equal to 0.41 and inter-rater reliability equal to 0.52. The factor analysis produced two indices and six subscales of the Standardised Copy of Pentagons Test (SCPT. The total score as well as most of the individual items and subscales distinguished between controls and patients. The discriminant function correctly classified 63.44% of controls and 75.59% of patients. Discussion The SCPT seems to be a satisfactory, reliable and valid instrument, which is easy to administer, suitable for use in non-organic psychiatric patients and demands minimal time. Further research is necessary to test its psychometric properties and its usefulness and applications as a neuropsychological test.

  1. Hard Diffraction at D{phi}

    Energy Technology Data Exchange (ETDEWEB)

    Alves, Gilvan A. [Centro Brasileiro de Pesquisas Fisicas (CBPF), Rio de Janeiro, RJ (Brazil). Lab. de Cosmologia e Fisica Experimental de Altas Energias

    2000-07-01

    Full text follows: We review recent Hard Diffraction results from the D{phi} experiment at Fermilab, for the following processes: hard color singlet exchange, hard single diffraction, and hard double pomeron exchange. Measurements of rates, {eta}, E{sub T} and {radical}S dependencies are presented and comparisons made with predictions of several models. (author)

  2. 38 CFR 1.526 - Copies of records and papers.

    Science.gov (United States)

    2010-07-01

    ... papers. 1.526 Section 1.526 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS... Copies of records and papers. (a) Any person desiring a copy of any record or document in the custody of... plain one-sided paper copies of a standard size (81/2″ × 11″; 81/2″ × 14″; 11″ × 14″) $0.15 per...

  3. Photon technology. Hard photon technology; Photon technology. Hard photon gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the application of photon to industrial technologies, in particular, a hard photon technology was surveyed which uses photon beams of 0.1-200nm in wavelength. Its features such as selective atom reaction, dense inner shell excitation and spacial high resolution by quantum energy are expected to provide innovative techniques for various field such as fine machining, material synthesis and advanced inspection technology. This wavelength region has been hardly utilized for industrial fields because of poor development of suitable photon sources and optical devices. The developmental meaning, usable time and issue of a hard photon reduction lithography were surveyed as lithography in ultra-fine region below 0.1{mu}m. On hard photon analysis/evaluation technology, the industrial use of analysis, measurement and evaluation technologies by micro-beam was viewed, and optimum photon sources and optical systems were surveyed. Prediction of surface and surface layer modification by inner shell excitation, the future trend of this process and development of a vacuum ultraviolet light source were also surveyed. 383 refs., 153 figs., 17 tabs.

  4. Charpy Impact Energy and Microindentation Hardness of 60-NITINOL

    Science.gov (United States)

    Stanford, Malcolm K.

    2012-01-01

    60-NITINOL (60 wt.% Ni 40 wt.% Ti) is being studied as a material for advanced aerospace components. The Charpy impact energy and microindentation hardness has been studied for this material, fabricated by vacuum induction skull melting (casting) and by hot isostatic pressing. Test specimens were prepared in various hardened and annealed heat treatment conditions. The average impact energy ranged from 0.33 to 0.49J for the hardened specimens while the annealed specimens had impact energies ranging from 0.89 to 1.18J. The average hardness values of the hardened specimens ranged from 590 to 676 HV while that of the annealed specimens ranged from 298 to 366 HV, suggesting an inverse relationship between impact energy and hardness. These results are expected to provide guidance in the selection of heat treatment processes for the design of mechanical components.

  5. Hard Diffraction in Pythia 8

    CERN Document Server

    Rasmussen, Christine O

    2015-01-01

    We present an overview of the options for diffraction implemented in the general--purpose event generator Pythia 8. We review the existing model for low-- and high--mass soft diffraction and present a new model for hard diffraction in pp and ppbar collisions. Both models uses the Pomeron approach pioneered by Ingelman and Schlein, factorising the single diffractive cross section into a Pomeron flux and a Pomeron PDF. The model for hard diffraction is implemented as a part of the multiparton interactions framework, thereby introducing a dynamical rapidity gap survival probability that explicitly breaks factorisation.

  6. Hard Diffraction in Pythia 8

    CERN Document Server

    Rasmussen, Christine O

    2015-01-01

    We present an overview of the options for diffraction implemented in the general-purpose event generator Pythia 8. We review the existing model for soft diffraction and present a new model for hard diffraction. Both models use the Pomeron approach pioneered by Ingelman and Schlein, factorising the diffractive cross section into a Pomeron flux and a Pomeron PDF, with several choices for both implemented in Pythia 8. The model of hard diffraction is implemented as a part of the multiparton interactions (MPI) framework, thus introducing a dynamical gap survival probability that explicitly breaks factorisation.

  7. Hard diffraction in Pythia 8

    Science.gov (United States)

    Overgaard Rasmussen, Christine

    2016-07-01

    We present an overview of the options for diffraction implemented in the general-purpose event generator Pythia 8 [1]. We review the existing model for soft diffraction and present a new model for hard diffraction. Both models use the Pomeron approach pioneered by Ingelman and Schlein, factorising the diffractive cross section into a Pomeron flux and a Pomeron PDF, with several choices for both implemented in Pythia 8. The model of hard diffraction is implemented as a part of the multiparton interactions (MPI) framework, thus introducing a dynamical gap survival probability that explicitly breaks factorisation.

  8. Quantum Copying Beyond the No-Cloning Theorem

    CERN Document Server

    Buzek, V; Buzek, Vladimir; Hillery, Mark

    1996-01-01

    We analyze to what extent it is possible to copy arbitrary states of a two-level quantum system. We show that there exists a "universal quantum copying machine", which approximately copies quantum mechanical states in such a way that the quality of its output does not depend on the input. We also examine a machine which combines a unitary transformation with a selective measurement to produce good copies of states in a neighborhood of a particular state. We discuss the problem of measurement of the output states.

  9. Genome-wide copy number analysis using copy number inferring tool (CNIT) and DNA pooling.

    Science.gov (United States)

    Lin, Chien-hsing; Huang, Mei-chu; Li, Ling-hui; Wu, Jer-yuarn; Chen, Yuan-tsong; Fann, Cathy S J

    2008-08-01

    Copy number variation (CNV) has become an important genomic structure element in the human population, and some CNVs are related to specific traits and diseases. Moreover, analysis of human genomes has been potentiated by the use of high-resolution microarrays that assess single nucleotide polymorphisms (SNPs). Although many programs have been designed to analyze data from Affymetrix SNP microarrays, they all have high false-positive rates (FPRs) in copy number (CN) analyses. Copy number analysis tool (CNAT) 4.0 is a recently developed program that offers improved CN estimation, but small amplifications and deletions are lost when using the smoothing procedure. Here, we propose a copy number inferring tool (CNIT) algorithm for the 100K SNP microarray to investigate CNVs at 29.6-kb resolution. CNIT estimated SNP allelic and total CN with reliable P values based on intensity data. In addition, the hidden Markov model (HMM) method was applied to predict regions having altered CN by considering contiguous SNPs. Based on a CN analysis of 23 unrelated Taiwanese and 30 HapMap Centre d'Etude du Polymorphisme Humain (CEPH) trios, CNIT showed higher accuracy and power than other programs. The FPRs and false-negative rates (FNRs) of CNIT were 0.1% and 0.16%, respectively. CNIT also showed better sensitivity for detecting small amplifications and deletions. Furthermore, DNA pooling of 10 and 30 normal unrelated individuals were applied to the 100K SNP microarray, respectively, and 12 common CN-variable regions were identified, suggesting that DNA pooling can be applied to discover common CNVs.

  10. Hard Trying and These Recipes

    Science.gov (United States)

    Atwell, Nancie

    2003-01-01

    Writers thrive when they are motivated to work hard, have regular opportunities to practice and reflect, and benefit from a knowledgeable teacher who knows writing. Student feedback to lessons during writing workshop helped guide Nancie Atwell in her quest to provide the richest and most efficient path to better writing.

  11. Kinetic theory of hard spheres

    NARCIS (Netherlands)

    Beijeren, H. van; Ernst, M.H.

    1979-01-01

    Kinetic equations for the hard-sphere system are derived by diagrammatic techniques. A linear equation is obtained for the one-particle-one particle equilibrium time correlation function and a nonlinear equation for the one-particle distribution function in nonequilibrium. Both equations are nonloca

  12. Metrics for Hard Goods Merchandising.

    Science.gov (United States)

    Cooper, Gloria S., Ed.; Magisos, Joel H., Ed.

    Designed to meet the job-related metric measurement needs of students interested in hard goods merchandising, this instructional package is one of five for the marketing and distribution cluster, part of a set of 55 packages for metric instruction in different occupations. The package is intended for students who already know the occupational…

  13. Inclusive Hard Diffraction at HERA

    CERN Document Server

    Proskuryakov, Alexander

    2010-01-01

    Recent data from the H1 and ZEUS experiments on hard inclusive diffraction are discussed. Results of QCD analyses of the diffractive deep-inelastic scattering processes are reported. Predictions based on the extracted parton densities are compared to diffractive dijet measurements.

  14. Hard sphere packings within cylinders.

    Science.gov (United States)

    Fu, Lin; Steinhardt, William; Zhao, Hao; Socolar, Joshua E S; Charbonneau, Patrick

    2016-03-07

    Arrangements of identical hard spheres confined to a cylinder with hard walls have been used to model experimental systems, such as fullerenes in nanotubes and colloidal wire assembly. Finding the densest configurations, called close packings, of hard spheres of diameter σ in a cylinder of diameter D is a purely geometric problem that grows increasingly complex as D/σ increases, and little is thus known about the regime for D > 2.873σ. In this work, we extend the identification of close packings up to D = 4.00σ by adapting Torquato-Jiao's adaptive-shrinking-cell formulation and sequential-linear-programming (SLP) technique. We identify 17 new structures, almost all of them chiral. Beyond D ≈ 2.85σ, most of the structures consist of an outer shell and an inner core that compete for being close packed. In some cases, the shell adopts its own maximum density configuration, and the stacking of core spheres within it is quasiperiodic. In other cases, an interplay between the two components is observed, which may result in simple periodic structures. In yet other cases, the very distinction between the core and shell vanishes, resulting in more exotic packing geometries, including some that are three-dimensional extensions of structures obtained from packing hard disks in a circle.

  15. Hard sphere model of atom

    CERN Document Server

    Tsekov, R

    2014-01-01

    The finite size effect of electron and nucleus is accounted for in the model of atom. Due to their hard sphere repulsion the energy of the 1s orbital decreases and the corrections amount up to 8 % in Uranium. Several models for boundary conditions on the atomic nucleus surface are discussed as well.

  16. Stress in hard metal films

    NARCIS (Netherlands)

    Janssen, G.C.A.M.; Kamminga, J.D.

    2004-01-01

    In the absence of thermal stress, tensile stress in hard metal films is caused by grain boundary shrinkage and compressive stress is caused by ion peening. It is shown that the two contributions are additive. Moreover tensile stress generated at the grain boundaries does not relax by ion bombardment

  17. Unifying approach to hard diffraction

    CERN Document Server

    Navelet, H

    2001-01-01

    We find a formulation of hard diffraction unifying the partonic (Ingelman-Schlein) Pomeron, Soft Colour Interaction and QCD dipole descriptions. A theoretical interpretation in terms of S-Matrix and perturbative QCD properties in the small x_{Bj} regime is proposed.

  18. Verrucous Carcinoma of Hard Plate

    OpenAIRE

    Parmod Kalstra,Monica Manhas,Rajdeep Sood

    2000-01-01

    VerrucouS squamous cell carcinoma occurs mainly in oral cavity and larynx, buccal mucosa being most commonly involved. One case of verrucous carcinoma involvmg left hard palate (T4 No Mo)in an adult male is being reported who underwent left total maxillectomy. The tumor behaviour andlts management has been dlscussed.

  19. New cytogenetically visible copy number variant in region 8q21.2

    Directory of Open Access Journals (Sweden)

    Ewers Elisabeth

    2011-01-01

    Full Text Available Abstract Background Cytogenetically visible unbalanced chromosomal abnormalities (UBCA, reported for >50 euchromatic regions of almost all human autosomes, are comprised of a few megabases of DNA, and carriers are in many cases clinically healthy. It may be speculated, that some of the UBCA may be similar or identical to copy number variants (CNV of the human genome. Results Here we report on a yet unreported cytogenetically visible copy number variant (CNV in the long arm of chromosome 8, region 8q21.2, detected in three unrelated clinically healthy carriers. Conclusion The first description of a cytogenetically visible CNV/UBCA in 8q21.2 shows that banding cytogenetics is far from being outdated. It is a cost efficient, up-to-date method for a single cell specific overview on the whole genome, still prepared to deliver unexpected findings.

  20. Accuracy estimation of foamy virus genome copying

    Directory of Open Access Journals (Sweden)

    Rethwilm Axel

    2009-04-01

    Full Text Available Abstract Background Foamy viruses (FVs are the most genetically stable viruses of the retrovirus family. This is in contrast to the in vitro error rate found for recombinant FV reverse transcriptase (RT. To investigate the accuracy of FV genome copying in vivo we analyzed the occurrence of mutations in HEK 293T cell culture after a single round of reverse transcription using a replication-deficient vector system. Furthermore, the frequency of FV recombination by template switching (TS and the cross-packaging ability of different FV strains were analyzed. Results We initially sequenced 90,000 nucleotides and detected 39 mutations, corresponding to an in vivo error rate of approximately 4 × 10-4 per site per replication cycle. Surprisingly, all mutations were transitions from G to A, suggesting that APOBEC3 activity is the driving force for the majority of mutations detected in our experimental system. In line with this, we detected a late but significant APOBEC3G and 3F mRNA by quantitative PCR in the cells. We then analyzed 170,000 additional nucleotides from experiments in which we co-transfected the APOBEC3-interfering foamy viral bet gene and observed a significant 50% drop in G to A mutations, indicating that APOBEC activity indeed contributes substantially to the foamy viral replication error rate in vivo. However, even in the presence of Bet, 35 out of 37 substitutions were G to A, suggesting that residual APOBEC activity accounted for most of the observed mutations. If we subtract these APOBEC-like mutations from the total number of mutations, we calculate a maximal intrinsic in vivo error rate of 1.1 × 10-5 per site per replication. In addition to the point mutations, we detected one 49 bp deletion within the analyzed 260000 nucleotides. Analysis of the recombination frequency of FV vector genomes revealed a 27% probability for a template switching (TS event within a 1 kilobase (kb region. This corresponds to a 98% probability that FVs

  1. 45 CFR 1703.404 - Copying and transcription charges.

    Science.gov (United States)

    2010-10-01

    ... 45 Public Welfare 4 2010-10-01 2010-10-01 false Copying and transcription charges. 1703.404... Copying and transcription charges. (a) The Commission will charge fees for furnishing records at the rate of ten cents per page for photocopies and at the actual cost of transcription. When the...

  2. Cover-Copy-Compare and Spelling: One versus Three Repetitions

    Science.gov (United States)

    Erion, Joel; Davenport, Cindy; Rodax, Nicole; Scholl, Bethany; Hardy, Jennifer

    2009-01-01

    Cover, copy, compare (CCC) has been used with success to improve spelling skills. This study adds to existing research by completing an analysis of the rewriting component of the intervention. The impact of varying the number of times a subject copied a word following an error was examined with four elementary age students. An adaptive alternating…

  3. Perceiving the Impossible: How Individuals with Autism Copy Paradoxical Figures

    Science.gov (United States)

    Sheppard, Elizabeth; Ropar, Danielle; Mitchell, Peter

    2009-01-01

    Mottron and colleagues found that individuals with autism were less affected by geometric impossibility than comparison participants on a copying task. The current experiment sought to determine whether a local perceptual style could account for this. Participants with and without autism copied possible and impossible geometric figures. Geometric…

  4. 48 CFR 6302.25 - Copies of papers (Rule 25).

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Copies of papers (Rule 25). 6302.25 Section 6302.25 Federal Acquisition Regulations System DEPARTMENT OF TRANSPORTATION BOARD OF CONTRACT APPEALS RULES OF PROCEDURE 6302.25 Copies of papers (Rule 25). When books, records, papers,...

  5. Vocal copying of individually distinctive signature whistles in bottlenose dolphins

    Science.gov (United States)

    King, Stephanie L.; Sayigh, Laela S.; Wells, Randall S.; Fellner, Wendi; Janik, Vincent M.

    2013-01-01

    Vocal learning is relatively common in birds but less so in mammals. Sexual selection and individual or group recognition have been identified as major forces in its evolution. While important in the development of vocal displays, vocal learning also allows signal copying in social interactions. Such copying can function in addressing or labelling selected conspecifics. Most examples of addressing in non-humans come from bird song, where matching occurs in an aggressive context. However, in other animals, addressing with learned signals is very much an affiliative signal. We studied the function of vocal copying in a mammal that shows vocal learning as well as complex cognitive and social behaviour, the bottlenose dolphin (Tursiops truncatus). Copying occurred almost exclusively between close associates such as mother–calf pairs and male alliances during separation and was not followed by aggression. All copies were clearly recognizable as such because copiers consistently modified some acoustic parameters of a signal when copying it. We found no evidence for the use of copying in aggression or deception. This use of vocal copying is similar to its use in human language, where the maintenance of social bonds appears to be more important than the immediate defence of resources. PMID:23427174

  6. Re-thinking copyright through the copy in Russia

    NARCIS (Netherlands)

    Sezneva, O.

    2013-01-01

    How one copy of a film or a single is made illegal, while its identical twin is treated as legitimate? By drawing from the material collected in Russia on the illegal copying and distribution of video and musical contents, this paper moves beyond the definition of media piracy in legal terms, and

  7. 7 CFR 3701.2 - Public inspection, copying, and indexing.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Public inspection, copying, and indexing. 3701.2 Section 3701.2 Agriculture Regulations of the Department of Agriculture (Continued) ECONOMIC RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE PUBLIC INFORMATION § 3701.2 Public inspection, copying, and indexing....

  8. 7 CFR 3801.2 - Public inspection, copying, and indexing.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Public inspection, copying, and indexing. 3801.2 Section 3801.2 Agriculture Regulations of the Department of Agriculture (Continued) WORLD AGRICULTURAL... inspection, copying, and indexing. 5 U.S.C. 552(a)(2) requires that certain materials be made available...

  9. 7 CFR 3404.2 - Public inspection, copying, and indexing.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Public inspection, copying, and indexing. 3404.2 Section 3404.2 Agriculture Regulations of the Department of Agriculture (Continued) COOPERATIVE STATE... inspection, copying, and indexing. 5 U.S.C. 552(a)(2) requires that certain materials be made available...

  10. 7 CFR 510.2 - Public inspection, copying, and indexing.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 6 2010-01-01 2010-01-01 false Public inspection, copying, and indexing. 510.2 Section 510.2 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL RESEARCH SERVICE, DEPARTMENT OF AGRICULTURE PUBLIC INFORMATION § 510.2 Public inspection, copying, and indexing....

  11. 27 CFR 25.301 - Photographic copies of records.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Photographic copies of records. 25.301 Section 25.301 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS BEER Records and Reports § 25.301 Photographic copies...

  12. Re-thinking copyright through the copy in Russia

    NARCIS (Netherlands)

    Sezneva, O.

    2013-01-01

    How one copy of a film or a single is made illegal, while its identical twin is treated as legitimate? By drawing from the material collected in Russia on the illegal copying and distribution of video and musical contents, this paper moves beyond the definition of media piracy in legal terms, and in

  13. 40 CFR 716.30 - Submission of copies of studies.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Submission of copies of studies. 716.30 Section 716.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT HEALTH AND SAFETY DATA REPORTING General Provisions § 716.30 Submission of copies of...

  14. Cache-based memory copy hardware accelerator for multicore systems

    NARCIS (Netherlands)

    Duarte, F.; Wong, S.

    2010-01-01

    In this paper, we present a new architecture of the cache-based memory copy hardware accelerator in a multicore system supporting message passing. The accelerator is able to accelerate memory data movements, in particular memory copies. We perform an analytical analysis based on open-queuing theory

  15. Schizophrenia copy number variants and associative learning

    Science.gov (United States)

    Clifton, N E; Pocklington, A J; Scholz, B; Rees, E; Walters, J T R; Kirov, G; O'Donovan, M C; Owen, M J; Wilkinson, L S; Thomas, K L; Hall, J

    2017-01-01

    Large-scale genomic studies have made major progress in identifying genetic risk variants for schizophrenia. A key finding from these studies is that there is an increased burden of genomic copy number variants (CNVs) in schizophrenia cases compared with controls. The mechanism through which these CNVs confer risk for the symptoms of schizophrenia, however, remains unclear. One possibility is that schizophrenia risk CNVs impact basic associative learning processes, abnormalities of which have long been associated with the disorder. To investigate whether genes in schizophrenia CNVs impact on specific phases of associative learning we combined human genetics with experimental gene expression studies in animals. In a sample of 11 917 schizophrenia cases and 16 416 controls, we investigated whether CNVs from patients with schizophrenia are enriched for genes expressed during the consolidation, retrieval or extinction of associative memories. We show that CNVs from cases are enriched for genes expressed during fear extinction in the hippocampus, but not genes expressed following consolidation or retrieval. These results suggest that CNVs act to impair inhibitory learning in schizophrenia, potentially contributing to the development of core symptoms of the disorder. PMID:27956746

  16. Expression of COPI components during development of Drosophila melanogaster.

    Science.gov (United States)

    Grieder, Nicole C; Kloter, Urs; Gehring, Walter J

    2005-12-01

    In a P{lArB} enhancer detector collection, a line was found that showed upregulated expression within centrally to posteriorly located germarial cysts. It was inserted in the gammaCOP locus on chromosome 3R. GammaCOP is a component of the COPI coatomer involved in membrane traffic. Most of the other known components of the COPI coatomer also showed higher expression in the posterior half of the germarium. Not only meiotic germline cysts but also migrating follicle cells upregulate the COPI subunits. During embryonic and larval development, the COPI subunits are expressed ubiquitously as expected for genes required for cell viability. In addition, they are strongly expressed in the salivary glands and the proventriculus. Whether tissue-specific transcriptional upregulation of COPI subunits is required for the reorganization of membranous compartments that are needed for the developmental processes that confer cyst polarity and follicle maturation will have to be addressed in a genetic study.

  17. Protocols for Copying and Proofreading in Template-Assisted Polymerization

    Science.gov (United States)

    Pigolotti, Simone; Sartori, Pablo

    2016-03-01

    We discuss how information encoded in a template polymer can be stochastically copied into a copy polymer. We consider four different stochastic copy protocols of increasing complexity, inspired by building blocks of the mRNA translation pathway. In the first protocol, monomer incorporation occurs in a single stochastic transition. We then move to a more elaborate protocol in which an intermediate step can be used for error correction. Finally, we discuss the operating regimes of two kinetic proofreading protocols: one in which proofreading acts from the final copying step, and one in which it acts from an intermediate step. We review known results for these models and, in some cases, extend them to analyze all possible combinations of energetic and kinetic discrimination. We show that, in each of these protocols, only a limited number of these combinations leads to an improvement of the overall copying accuracy.

  18. The double copy: Bremsstrahlung and accelerating black holes

    CERN Document Server

    Luna, Andres; Nicholson, Isobel; O'Connell, Donal; White, Chris D

    2016-01-01

    Advances in our understanding of perturbation theory suggest the existence of a correspondence between classical general relativity and Yang-Mills theory. A concrete example of this correspondence, which is known as the double copy, was recently introduced for the case of stationary Kerr-Schild spacetimes. Building on this foundation, we examine the simple time-dependent case of an accelerating, radiating point source. The gravitational solution, which generalises the Schwarzschild solution, includes a non-trivial stress-energy tensor. This stress-energy tensor corresponds to a gauge theoretic current in the double copy. We interpret both of these sources as representing the radiative part of the field. Furthermore, in the simple example of Bremsstrahlung, we determine a scattering amplitude describing the radiation, maintaining the double copy throughout. Our results provide the strongest evidence yet that the classical double copy is directly related to the BCJ double copy for scattering amplitudes.

  19. FERTILIZER SALES AND SERVICEMAN. TEACHERS COPY.

    Science.gov (United States)

    WIGGS, J.T.; AND OTHERS

    THE PURPOSE OF THIS DOCUMENT IS TO PROVIDE A STUDY GUIDE FOR STUDENTS PREPARING TO BE FERTILIZER SALES AND SERVICEMEN IN A COOPERATIVE EDUCATION PROGRAM. IT WAS DESIGNED BY SUBJECT MATTER SPECIALISTS ON THE BASIS OF RECOMMENDATIONS BY A STATE ADVISORY COMMITTEE, TESTED IN OPERATIONAL PROGRAMS, AND REFINED BY A VOCATIONAL AGRICULTURE TEACHER. UNITS…

  20. Trivalent Gd-DOTA reagents for modification of proteins† †Electronic supplementary information (ESI) available: Synthetic details for known compounds; materials and methods for bioconjugation reactions; copies of spectra of new compounds and compounds prepared according to new procedures. See DOI: 10.1039/c5ra20359g Click here for additional data file.

    Science.gov (United States)

    Fisher, Martin J.; Williamson, Daniel J.; Burslem, George M.; Plante, Jeffrey P.; Manfield, Iain W.; Tiede, Christian; Ault, James R.; Stockley, Peter G.; Plein, Sven; Maqbool, Azhar; Tomlinson, Darren C.; Foster, Richard; Warriner, Stuart L.

    2015-01-01

    The development of novel protein-targeted MRI contrast agents crucially depends on the ability to derivatise suitable targeting moieties with a high payload of relaxation enhancer (e.g., gadolinium(iii) complexes such as Gd-DOTA), without losing affinity for the target proteins. Here, we report robust synthetic procedures for the preparation of trivalent Gd-DOTA reagents with various chemical handles for site-specific modification of biomolecules. The reagents were shown to successfully label proteins through isothiocyanate ligation or through site-specific thiol–maleimide ligation and strain-promoted azide–alkyne cycloaddition. PMID:27019702

  1. The Differential Effects of Two Self-Managed Math Instruction Procedures: Cover, Copy, and Compare versus Copy, Cover, and Compare

    Science.gov (United States)

    Grafman, Joel M.; Cates, Gary L.

    2010-01-01

    This study compared the fluency and error rates produced when using the Cover, Copy, and Compare (CCC) and a modified CCC procedure (MCCC) called Copy, Cover, and Compare to complete subtraction math problems. Two second-grade classrooms consisting of 47 total students participated in the study. The following items were administered to…

  2. Eclipse period of R1 plasmids during downshift from elevated copy number: Nonrandom selection of copies for replication.

    Science.gov (United States)

    Olsson, Jan A; Berg, Otto; Nordström, Kurt; Dasgupta, Santanu

    2012-03-01

    The classical Meselson-Stahl density-shift method was used to study replication of pOU71, a runaway-replication derivative of plasmid R1 in Escherichia coli. The miniplasmid maintained the normal low copy number of R1 during steady growth at 30°C, but as growth temperatures were raised above 34°C, the copy number of the plasmid increased to higher levels, and at 42°C, it replicated without control in a runaway replication mode with lethal consequences for the host. The eclipse periods (minimum time between successive replication of the same DNA) of the plasmid shortened with rising copy numbers at increasing growth temperatures (Olsson et al., 2003). In this work, eclipse periods were measured during downshifts in copy number of pOU71 after it had replicated at 39 and 42°C, resulting in 7- and 50-fold higher than normal plasmid copy number per cell, respectively. Eclipse periods for plasmid replication, measured during copy number downshift, suggested that plasmid R1, normally selected randomly for replication, showed a bias such that a newly replicated DNA had a higher probability of replication compared to the bulk of the R1 population. However, even the unexpected nonrandom replication followed the copy number kinetics such that every generation, the plasmids underwent the normal inherited number of replication, n, independent of the actual number of plasmid copies in a newborn cell.

  3. Molecular hardness and softness, local hardness and softness, hardness and softness kernels, and relations among these quantities

    Science.gov (United States)

    Berkowitz, Max; Parr, Robert G.

    1988-02-01

    Hardness and softness kernels η(r,r') and s(r,r') are defined for the ground state of an atomic or molecular electronic system, and the previously defined local hardness and softness η(r) and s(r) and global hardness and softness η and S are obtained from them. The physical meaning of s(r), as a charge capacitance, is discussed (following Huheey and Politzer), and two alternative ``hardness'' indices are identified and briefly discussed.

  4. Ultrasonic material hardness depth measurement

    Science.gov (United States)

    Good, Morris S.; Schuster, George J.; Skorpik, James R.

    1997-01-01

    The invention is an ultrasonic surface hardness depth measurement apparatus and method permitting rapid determination of hardness depth of shafts, rods, tubes and other cylindrical parts. The apparatus of the invention has a part handler, sensor, ultrasonic electronics component, computer, computer instruction sets, and may include a display screen. The part handler has a vessel filled with a couplant, and a part rotator for rotating a cylindrical metal part with respect to the sensor. The part handler further has a surface follower upon which the sensor is mounted, thereby maintaining a constant distance between the sensor and the exterior surface of the cylindrical metal part. The sensor is mounted so that a front surface of the sensor is within the vessel with couplant between the front surface of the sensor and the part.

  5. Development of Radiation Hard Scintillators

    CERN Document Server

    Tiras, Emrah; Bilki, Burak; Winn, David; Onel, Yasar

    2016-01-01

    Modern high-energy physics experiments are in ever increasing need for radiation hard scintillators and detectors. In this regard, we have studied various radiation-hard scintillating materials such as Polyethylene Naphthalate (PEN), Polyethylene Terephthalate (PET), our prototype material Scintillator X (SX) and Eljen (EJ). Scintillation and transmission properties of these scintillators are studied using stimulated emission from a 334 nm wavelength UV laser with PMT before and after certain amount of radiation exposure. Recovery from radiation damage is studied over time. While the primary goal of this study is geared for LHC detector upgrades, these new technologies could easily be used for future experiments such as the FCC and ILC. Here we discuss the physics motivation, recent developments and laboratory measurements of these materials.

  6. Schwannoma of the hard palate

    OpenAIRE

    2009-01-01

    Schwannomas are benign encapsulated perineural tumors. The head and neck region is the most common site. Intraoral origin is seen in only 1% of cases, tongue being the most common site; its location in the palate is rare. We report a case of hard-palate schwannoma with bony erosion which was immunohistochemically confirmed. The tumor was excised completely intraorally. After two months of follow-up, the defect was found to be completely covered with palatal mucosa.

  7. Copy number analysis of the low-copy repeats at the primate NPHP1 locus by array comparative genomic hybridization.

    Science.gov (United States)

    Yuan, Bo; Liu, Pengfei; Rogers, Jeffrey; Lupski, James R

    2016-06-01

    Array comparative genomic hybridization (aCGH) has been widely used to detect copy number variants (CNVs) in both research and clinical settings. A customizable aCGH platform may greatly facilitate copy number analyses in genomic regions with higher-order complexity, such as low-copy repeats (LCRs). Here we present the aCGH analyses focusing on the 45 kb LCRs [1] at the NPHP1 region with diverse copy numbers in humans. Also, the interspecies aCGH analysis comparing human and nonhuman primates revealed dynamic copy number transitions of the human 45 kb LCR orthologues during primate evolution and therefore shed light on the origin of complexity at this locus. The original aCGH data are available at GEO under GSE73962.

  8. mtDNA copy number in oocytes of different sizes from individual pre- and post-pubertal pigs

    DEFF Research Database (Denmark)

    Pedersen, Hanne Skovsgaard; Løvendahl, Peter; Larsen, Knud Erik

    2014-01-01

    Reproduction 131, 233–245). However, the correlation between size and mtDNA copy number in single oocytes has not been determined. This study describes the relation between oocytes of defined diameters from individual pre- and postpubertal pigs and mtDNA copy number. Cumulus-oocyte complexes were aspirated......Oocyte competence has been related to mtDNA copy number, but a large variation in mtDNA copy number between oocytes has been observed, caused by, e.g. oocyte donor and oocyte size (Sato et al. 2014 PLOS ONE 9, e94488; Cotterill et al. 2013 Mol. Hum. Reprod. 19, 444–450; El Shourbagy et al. 2006...... from ovaries of 10 pre- and 10 post-pubertal pigs. Cumulus cells were removed and the oocytes were measured (inside-ZP-diameter). Oocytes were transferred to DNAase-free tubes, snap-frozen, and stored at –80°C. The genes ND1 and COX1 were used to determine the mtDNA copy number. Plasmid preparations...

  9. Comparison of the marginal gap of zirconia-fabricated copings generated by CAD/CAM and Copy-Milling methods

    Directory of Open Access Journals (Sweden)

    Abdolhamid Alhavaz

    2015-01-01

    Full Text Available Introduction: This study was conducted to compare the marginal fit of single-tooth zirconia-based copings fabricated by CAD/CAM process (Cercon; Degudent and Copy Milling (Dentium. Materials and Methods: One in vitro prepared abutment from one mandibular molar model served as a template for replication of 40 epoxy resin (highly filled dies, which had been taken by polyvinyl siloxane impression material. Copings were manufactured on epoxy replicas by two processes: the CAD/CAM (Cercon; Degudent (n = 20 and the Copy-Milling (Dentium (n = 20 processes. Four measurements were performed for each surface coping (Buccal, Lingual, Mesial, and Distal. Data were analyzed by SPSS 16 statistical software using independent t-test. Results: There was a significant difference in the marginal gap values between CAD/CAM and Copy-Milling groups (P < 0.001. The mean value of the marginal gap (SD for CAD/CAM Copings (56.87 μm was significantly less than that of Copy-Milling (136.12 μm (P < 0.001. Conclusion: The marginal fit of CAD/CAM copings was better than that of Copy-Milling copings.

  10. Playing Moderately Hard to Get

    Directory of Open Access Journals (Sweden)

    Stephen Reysen

    2013-12-01

    Full Text Available In two studies, we examined the effect of different degrees of attraction reciprocation on ratings of attraction toward a potential romantic partner. Undergraduate college student participants imagined a potential romantic partner who reciprocated a low (reciprocating attraction one day a week, moderate (reciprocating attraction three days a week, high (reciprocating attraction five days a week, or unspecified degree of attraction (no mention of reciprocation. Participants then rated their degree of attraction toward the potential partner. The results of Study 1 provided only partial support for Brehm’s emotion intensity theory. However, after revising the high reciprocation condition vignette in Study 2, supporting Brehm’s emotion intensity theory, results show that a potential partners’ display of reciprocation of attraction acted as a deterrent to participants’ intensity of experienced attraction to the potential partner. The results support the notion that playing moderately hard to get elicits more intense feelings of attraction from potential suitors than playing too easy or too hard to get. Discussion of previous research examining playing hard to get is also re-examined through an emotion intensity theory theoretical lens.

  11. Copy number variation in the horse genome.

    Directory of Open Access Journals (Sweden)

    Sharmila Ghosh

    2014-10-01

    Full Text Available We constructed a 400K WG tiling oligoarray for the horse and applied it for the discovery of copy number variations (CNVs in 38 normal horses of 16 diverse breeds, and the Przewalski horse. Probes on the array represented 18,763 autosomal and X-linked genes, and intergenic, sub-telomeric and chrY sequences. We identified 258 CNV regions (CNVRs across all autosomes, chrX and chrUn, but not in chrY. CNVs comprised 1.3% of the horse genome with chr12 being most enriched. American Miniature horses had the highest and American Quarter Horses the lowest number of CNVs in relation to Thoroughbred reference. The Przewalski horse was similar to native ponies and draft breeds. The majority of CNVRs involved genes, while 20% were located in intergenic regions. Similar to previous studies in horses and other mammals, molecular functions of CNV-associated genes were predominantly in sensory perception, immunity and reproduction. The findings were integrated with previous studies to generate a composite genome-wide dataset of 1476 CNVRs. Of these, 301 CNVRs were shared between studies, while 1174 were novel and require further validation. Integrated data revealed that to date, 41 out of over 400 breeds of the domestic horse have been analyzed for CNVs, of which 11 new breeds were added in this study. Finally, the composite CNV dataset was applied in a pilot study for the discovery of CNVs in 6 horses with XY disorders of sexual development. A homozygous deletion involving AKR1C gene cluster in chr29 in two affected horses was considered possibly causative because of the known role of AKR1C genes in testicular androgen synthesis and sexual development. While the findings improve and integrate the knowledge of CNVs in horses, they also show that for effective discovery of variants of biomedical importance, more breeds and individuals need to be analyzed using comparable methodological approaches.

  12. Copy number variation in the horse genome.

    Science.gov (United States)

    Ghosh, Sharmila; Qu, Zhipeng; Das, Pranab J; Fang, Erica; Juras, Rytis; Cothran, E Gus; McDonell, Sue; Kenney, Daniel G; Lear, Teri L; Adelson, David L; Chowdhary, Bhanu P; Raudsepp, Terje

    2014-10-01

    We constructed a 400K WG tiling oligoarray for the horse and applied it for the discovery of copy number variations (CNVs) in 38 normal horses of 16 diverse breeds, and the Przewalski horse. Probes on the array represented 18,763 autosomal and X-linked genes, and intergenic, sub-telomeric and chrY sequences. We identified 258 CNV regions (CNVRs) across all autosomes, chrX and chrUn, but not in chrY. CNVs comprised 1.3% of the horse genome with chr12 being most enriched. American Miniature horses had the highest and American Quarter Horses the lowest number of CNVs in relation to Thoroughbred reference. The Przewalski horse was similar to native ponies and draft breeds. The majority of CNVRs involved genes, while 20% were located in intergenic regions. Similar to previous studies in horses and other mammals, molecular functions of CNV-associated genes were predominantly in sensory perception, immunity and reproduction. The findings were integrated with previous studies to generate a composite genome-wide dataset of 1476 CNVRs. Of these, 301 CNVRs were shared between studies, while 1174 were novel and require further validation. Integrated data revealed that to date, 41 out of over 400 breeds of the domestic horse have been analyzed for CNVs, of which 11 new breeds were added in this study. Finally, the composite CNV dataset was applied in a pilot study for the discovery of CNVs in 6 horses with XY disorders of sexual development. A homozygous deletion involving AKR1C gene cluster in chr29 in two affected horses was considered possibly causative because of the known role of AKR1C genes in testicular androgen synthesis and sexual development. While the findings improve and integrate the knowledge of CNVs in horses, they also show that for effective discovery of variants of biomedical importance, more breeds and individuals need to be analyzed using comparable methodological approaches.

  13. Why Are Drugs So Hard to Quit?

    Medline Plus

    Full Text Available ... Quitting drugs is hard because addiction is a brain disease. Your brain is like a control tower that sends out ... and choices. Addiction changes the signals in your brain and makes it hard to feel OK without ...

  14. Why Are Drugs So Hard to Quit?

    Medline Plus

    Full Text Available ... Quitting drugs is hard because addiction is a brain disease. Your brain is like a control tower that sends out ... and choices. Addiction changes the signals in your brain and makes it hard to feel OK without ...

  15. Mitochondrial DNA copy number in peripheral blood and melanoma risk.

    Directory of Open Access Journals (Sweden)

    Jie Shen

    Full Text Available Mitochondrial DNA (mtDNA copy number in peripheral blood has been suggested as risk modifier in various types of cancer. However, its influence on melanoma risk is unclear. We evaluated the association between mtDNA copy number in peripheral blood and melanoma risk in 500 melanoma cases and 500 healthy controls from an ongoing melanoma study. The mtDNA copy number was measured using real-time polymerase chain reaction. Overall, mean mtDNA copy number was significantly higher in cases than in controls (1.15 vs 0.99, P<0.001. Increased mtDNA copy number was associated with a 1.45-fold increased risk of melanoma (95% confidence interval: 1.12-1.97. Significant joint effects between mtDNA copy number and variables related to pigmentation and history of sunlight exposure were observed. This study supports an association between increased mtDNA copy number and melanoma risk that is independent on the known melanoma risk factors (pigmentation and history of sunlight exposure.

  16. Raman Model Predicting Hardness of Covalent Crystals

    OpenAIRE

    Zhou, Xiang-Feng; Qian, Quang-Rui; Sun, Jian; Tian, Yongjun; Wang, Hui-Tian

    2009-01-01

    Based on the fact that both hardness and vibrational Raman spectrum depend on the intrinsic property of chemical bonds, we propose a new theoretical model for predicting hardness of a covalent crystal. The quantitative relationship between hardness and vibrational Raman frequencies deduced from the typical zincblende covalent crystals is validated to be also applicable for the complex multicomponent crystals. This model enables us to nondestructively and indirectly characterize the hardness o...

  17. Tribological characterization of selected hard coatings

    OpenAIRE

    Karlsson, Patrik

    2009-01-01

    Hard coatings are often used for protection of tool surfaces due to coating properties like low friction and high wear resistance. Even though many of the hard coatings have been tested for wear, it is important to try new wear test setups to fully understand tribological mechanisms and the potential of hard coatings. Few experiments have been performed with dual-coated systems where the sliding contact surfaces are coated with the same, or different, hard coating. The dual-coated system coul...

  18. WC颗粒对激光熔覆FeCoCrNiCu高熵合金涂层组织与硬度的影响%Effects of WC Particles on the Microstructure and Hardness of FeCoCrNiCu High-entropy Alloy Coating Prepared by Laser Cladding

    Institute of Scientific and Technical Information of China (English)

    黄祖凤; 张冲; 唐群华; 戴品强; 吴波

    2013-01-01

    FeCoCrNiCu high-entropy alloy coating with WC particles was prepared by the continuous wave CO2 laser. The effects of WC particles on the microstructure and hardness were investigated. Results show that the high entropy alloy coatings with different WC content are all composed of face-centered cubic (FCC) and body-centered cubic (BCC) solid solution phases. With the increase of WC content, BCC phase content increases and FCC phase content decreases. During the process of laser cladding, WC particles dissolved into the FCC and BCC phases, however, the addition of WC does not cause the formation of complex carbide phases. The microstructure of coatings with different WC content is typical dendrite. Element segregation between the dendrite and interdendrite can be effectively inhibited by laser cladding with rapid solidification. The increase of WC content lead to grain refinement and microhardness increasing.%采用CO2横流激光器制备添加WC颗粒的FeCoCrNiCu高熵合金涂层,研究WC含量对涂层的组织结构及硬度的影响.结果表明:不同WC含量的高熵合金涂层均由简单的面心立方结构(FCC)和体心立方结构(BCC)两相组成.随着WC含量的提高,涂层中FCC相含量不断减少,BCC相含量不断增加.WC颗粒在激光熔覆过程中发生溶解并完全溶入FCC相和BCC相中,并未引起复杂碳化物相的生成.不同WC含量的涂层均为树枝晶组织.激光熔覆过程中的快速凝固条件有利于抑制枝晶和枝晶间的成分偏聚.WC含量的提高使枝晶细化,硬度提高.

  19. Properly coloured copies and rainbow copies of large graphs with small maximum degree

    CERN Document Server

    Böttcher, Julia; Procacci, Aldo

    2010-01-01

    Let G be a graph on n vertices with maximum degree D. We use the Lov\\'asz local lemma to show the following two results about colourings c of the edges of the complete graph K_n. If for each vertex v of K_n the colouring c assigns each colour to at most (n-2)/22.4D^2 edges emanating from v, then there is a copy of G in K_n which is properly edge-coloured by c. This improves on a result of Alon, Jiang, Miller, and Pritikin [Random Struct. Algorithms 23(4), 409-433, 2003]. On the other hand, if c assigns each colour to at most n/51D^2 edges of K_n, then there is a copy of G in K_n such that each edge of G receives a different colour from c. This proves a conjecture of Frieze and Krivelevich [Electron. J. Comb. 15(1), R59, 2008]. Our proofs rely on a framework developed by Lu and Sz\\'ekely [Electron. J. Comb. 14(1), R63, 2007] for applying the local lemma to random injections. In order to improve the constants in our results we use a version of the local lemma due to Bissacot, Fern\\'andez, Procacci, and Scoppola...

  20. 7 CFR 201.21 - Hard seed.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Hard seed. 201.21 Section 201.21 Agriculture..., Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) FEDERAL SEED ACT FEDERAL SEED ACT REGULATIONS Labeling Agricultural Seeds § 201.21 Hard seed. The label shall show the percentage of hard...

  1. 7 CFR 201.30 - Hard seed.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Hard seed. 201.30 Section 201.30 Agriculture..., Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE (CONTINUED) FEDERAL SEED ACT FEDERAL SEED ACT REGULATIONS Labeling Vegetable Seeds § 201.30 Hard seed. The label shall show the percentage of hard seed,...

  2. The classical double copy for Taub-NUT spacetime

    CERN Document Server

    Luna, A; O'Connell, D; White, C D

    2015-01-01

    The double copy is a much-studied relationship between gauge theory and gravity amplitudes. Recently, this was generalised to an infinite family of classical solutions to Einstein's equations, namely stationary Kerr-Schild geometries. In this paper, we extend this to the Taub-NUT solution in gravity, which has a double Kerr-Schild form. The single copy of this solution is a dyon, whose electric and magnetic charges are related to the mass and NUT charge in the gravity theory. Finally, we find hints that the classical double copy extends to curved background geometries.

  3. The classical double copy for Taub-NUT spacetime

    Science.gov (United States)

    Luna, Andrés; Monteiro, Ricardo; O'Connell, Donal; White, Chris D.

    2015-11-01

    The double copy is a much-studied relationship between gauge theory and gravity amplitudes. Recently, this was generalised to an infinite family of classical solutions to Einstein's equations, namely stationary Kerr-Schild geometries. In this paper, we extend this to the Taub-NUT solution in gravity, which has a double Kerr-Schild form. The single copy of this solution is a dyon, whose electric and magnetic charges are related to the mass and NUT charge in the gravity theory. Finally, we find hints that the classical double copy extends to curved background geometries.

  4. Comparison of time-dependent changes in the surface hardness of different composite resins

    Science.gov (United States)

    Ozcan, Suat; Yikilgan, Ihsan; Uctasli, Mine Betul; Bala, Oya; Kurklu, Zeliha Gonca Bek

    2013-01-01

    Objective: The aim of this study was to evaluate the change in surface hardness of silorane-based composite resin (Filtek Silorane) in time and compare the results with the surface hardness of two methacrylate-based resins (Filtek Supreme and Majesty Posterior). Materials and Methods: From each composite material, 18 wheel-shaped samples (5-mm diameter and 2-mm depth) were prepared. Top and bottom surface hardness of these samples was measured using a Vicker's hardness tester. The samples were then stored at 37°C and 100% humidity. After 24 h and 7, 30 and 90 days, the top and bottom surface hardness of the samples was measured. In each measurement, the rate between the hardness of the top and bottom surfaces were recorded as the hardness rate. Statistical analysis was performed by one-way analysis of variance, multiple comparisons by Tukey's test and binary comparisons by t-test with a significance level of P = 0.05. Results: The highest hardness values were obtained from each two surfaces of Majesty Posterior and the lowest from Filtek Silorane. Both the top and bottom surface hardness of the methacrylate based composite resins was high and there was a statistically significant difference between the top and bottom hardness values of only the silorane-based composite, Filtek Silorane (P < 0.05). The lowest was obtained with Filtek Silorane. The hardness values of all test groups increased after 24 h (P < 0.05). Conclusion: Although silorane-based composite resin Filtek Silorane showed adequate hardness ratio, the use of incremental technic during application is more important than methacrylate based composites. PMID:24966724

  5. Copy number gain of VCX, X-linked multi-copy gene, leads to cell proliferation and apoptosis during spermatogenesis

    Science.gov (United States)

    Ji, Juan; Qin, Yufeng; Wang, Rong; Huang, Zhenyao; Zhang, Yan; Zhou, Ran; Song, Ling; Ling, Xiufeng; Hu, Zhibin; Miao, Dengshun; Shen, Hongbing; Xia, Yankai; Wang, Xinru; Lu, Chuncheng

    2016-01-01

    Male factor infertility affects one-sixth of couples worldwide, and non-obstructive azoospermia (NOA) is one of the most severe forms. In recent years there has been increasing evidence to implicate the participation of X chromosome in the process of spermatogenesis. To uncover the roles of X-linked multi-copy genes in spermatogenesis, we performed systematic analysis of X-linked gene copy number variations (CNVs) and Y chromosome haplogrouping in 447 idiopathic NOA patients and 485 healthy controls. Interestingly, the frequency of individuals with abnormal level copy of Variable charge, X-linked (VCX) was significantly different between cases and controls after multiple test correction (p = 5.10 × 10−5). To discriminate the effect of gain/loss copies in these genes, we analyzed the frequency of X-linked multi-copy genes in subjects among subdivided groups. Our results demonstrated that individuals with increased copy numbers of Nuclear RNA export factor 2 (NXF2) (p = 9.21 × 10−8) and VCX (p = 1.97 × 10−4) conferred the risk of NOA. In vitro analysis demonstrated that increasing copy number of VCX could upregulate the gene expression and regulate cell proliferation and apoptosis. Our study establishes a robust association between the VCX CNVs and NOA risk. PMID:27705943

  6. Copy number gain of VCX, X-linked multi-copy gene, leads to cell proliferation and apoptosis during spermatogenesis.

    Science.gov (United States)

    Ji, Juan; Qin, Yufeng; Wang, Rong; Huang, Zhenyao; Zhang, Yan; Zhou, Ran; Song, Ling; Ling, Xiufeng; Hu, Zhibin; Miao, Dengshun; Shen, Hongbing; Xia, Yankai; Wang, Xinru; Lu, Chuncheng

    2016-11-29

    Male factor infertility affects one-sixth of couples worldwide, and non-obstructive azoospermia (NOA) is one of the most severe forms. In recent years there has been increasing evidence to implicate the participation of X chromosome in the process of spermatogenesis. To uncover the roles of X-linked multi-copy genes in spermatogenesis, we performed systematic analysis of X-linked gene copy number variations (CNVs) and Y chromosome haplogrouping in 447 idiopathic NOA patients and 485 healthy controls. Interestingly, the frequency of individuals with abnormal level copy of Variable charge, X-linked (VCX) was significantly different between cases and controls after multiple test correction (p = 5.10 × 10-5). To discriminate the effect of gain/loss copies in these genes, we analyzed the frequency of X-linked multi-copy genes in subjects among subdivided groups. Our results demonstrated that individuals with increased copy numbers of Nuclear RNA export factor 2 (NXF2) (p = 9.21 × 10-8) and VCX (p = 1.97 × 10-4) conferred the risk of NOA. In vitro analysis demonstrated that increasing copy number of VCX could upregulate the gene expression and regulate cell proliferation and apoptosis. Our study establishes a robust association between the VCX CNVs and NOA risk.

  7. Expulsion characterization in resistance spot welding by means of a hardness mapping technique

    Institute of Scientific and Technical Information of China (English)

    H.Ghazanfari; M.Naderi

    2014-01-01

    Expulsion is an undesired event during resistance spot welding because the weld quality deteriorates. It is the ejection of molten metal from the weld nugget which usually occurs due to applying a high current for a short welding time. Expulsion has a significant impact on the final yield strength of the weld, thus the detection and characterization of expulsion events is significant for the quality assurance of resistance spot welds. In this study, hardness mapping, using a scanning hardness machine, was used as a quality assurance technique for re-sistance spot welding. Hardness tests were conducted on a resistance spot welded sample to prepare a hardness map. The test results showed good correlation between the hardness map and metallographic cross sections. The technique also provided further fundamental understand-ing of the resistance spot welding process, especially regarding the occurrence of expulsion in the nugget.

  8. Effect of insertion method on knoop hardness of high viscous glass ionomer cements.

    Science.gov (United States)

    Raggio, Daniela Prócida; Bonifácio, Clarissa Calil; Bönecker, Marcelo; Imparato, José Carlos P; Gee, Anton J de; Amerongen, Willem Evert van

    2010-01-01

    The aim of this study was to assess the Knoop hardness of three high viscous glass ionomer cements: G1 - Ketac Molar; G2 - Ketac Molar Easymix (3M ESPE) and G3 - Magic Glass ART (Vigodent). As a parallel goal, three different methods for insertion of Ketac Molar Easymix were tested: G4 - conventional spatula; G5 - commercial syringe (Centrix) and G6 - low-cost syringe. Ten specimens of each group were prepared and the Knoop hardness was determined 5 times on each specimen with a HM-124 hardness machine (25 g/30 s dwell time) after 24 h, 1 and 2 weeks. During the entire test period, the specimens were stored in liquid paraffin at 37ºC. Significant differences were found between G3 and G1/G2 (two-way ANOVA and Tukey's post hoc test; pMagic Glass ART showed the lowest hardness, while the insertion technique had no significant influence on hardness.

  9. Hardness and stress of amorphous carbon film deposited by glow discharge and ion beam assisting deposition

    CERN Document Server

    Marques, F C

    2000-01-01

    The hardness and stress of amorphous carbon films prepared by glow discharge and by ion beam assisting deposition are investigated. Relatively hard and almost stress free amorphous carbon films were deposited by the glow discharge technique. On the other hand, by using the ion beam assisting deposition, hard films were also obtained with a stress of the same order of those found in tetrahedral amorphous carbon films. A structural analysis indicates that all films are composed of a sp sup 2 -rich network. These results contradict the currently accepted concept that both stress and hardness are only related to the concentration of sp sup 3 sites. Furthermore, the same results also indicate that the sp sup 2 sites may also contribute to the hardness of the films.

  10. Aespoe Hard Rock Laboratory Annual Report 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-08-01

    The Aespoe Hard Rock Laboratory has been constructed as part of the preparations for the deep geological repository for spent nuclear fuel in Sweden. The Tracer Retention Understanding Experiments are made to gain a better understanding of radionuclide retention in the rock and create confidence in the radionuclide transport models that are intended to be used in the licensing of a deep repository for spent fuel. The TRUE -1 experiment including tests with sorbing radioactive tracers in a single fracture over a distance of about 5 m has been completed. Diffusion and sorption in the rock matrix is the dominant retention mechanism over the time scales of the experiments. The main objective of the TRUE Block Scale Experiment is to increase understanding and our ability to predict tracer transport in a fracture network over spatial scales of 10 to 50 m. In total six boreholes have been drilled into the experimental volume located at the 450 m level. The Long-Term Diffusion Experiment is intended as a complement to the dynamic in-situ experiments and the laboratory experiments performed in the TRUE Programme. Diffusion from a fracture into the rock matrix will be studied in situ. The REX project focuses on the reduction of oxygen in a repository after closure due to reactions with rock minerals and microbial activity. Results show that oxygen is consumed within a few days both for the field and laboratory experiments. A new site for the CHEMLAB experiments was selected and prepared during 1999. All future experiment will be conducted in the J niche at 450 m depth. The Prototype Repository Test is focused on testing and demonstrating repository system function. A full-scale prototype including six deposition holes with canisters with electric heaters surrounded by highly compacted bentonite will be built and instrumented. Characterisation of the rock mass in the area of the Prototype repository is completed and the six deposition holes have been drilled. The Backfill and

  11. Aespoe Hard Rock Laboratory. Annual report 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    The Aespoe Hard Rock Laboratory has been constructed as part of the preparations for the deep geological repository for spent nuclear fuel in Sweden. The surface and borehole investigations and the research work performed in parallel with construction have provided a thorough test of methods for investigation and evaluation of bedrock conditions for construction of a deep repository. The Tracer Retention Understanding Experiments are made to gain a better understanding of radionuclide retention in the rock and create confidence in the radionuclide transport models that are intended to be used in the licensing of a deep repository for spent fuel. The experimental results of the first tracer test with sorbing radioactive tracers have been obtained. These tests have been subject to blind predictions by the Aespoe Task Force on groundwater flow and transports of solutes. The manufacturing of the CHEMLAB probe was completed during 1996, and the first experiments were started early in 1997. During 1997 three experiments on diffusion in bentonite using {sup 57}Co, {sup 114}Cs,{sup 85}Sr, {sup 99}Tc, and {sup 131}I were conducted. The Prototype Repository Test is focused on testing and demonstrating repository system function. A full scale prototype including six deposition holes with canisters with electric heaters surrounded by highly compacted bentonite will be built and instrumented. The characterization of the rock mass in the area of the prototype repository is in progress. The objectives of the Demonstration of Repository Technology are to develop, test, and demonstrate methodology and equipment for encapsulation and deposition of spent nuclear fuel. The demonstration of handling and deposition will be made in a new drift. The Backfill and Plug Test includes tests of backfill materials and emplacement methods and a test of a full scale plug. The backfill and rock will be instrumented with about 230 transducers for measuring the thermo-hydro-mechanical processes. The

  12. The hard problem of cooperation.

    Directory of Open Access Journals (Sweden)

    Kimmo Eriksson

    Full Text Available Based on individual variation in cooperative inclinations, we define the "hard problem of cooperation" as that of achieving high levels of cooperation in a group of non-cooperative types. Can the hard problem be solved by institutions with monitoring and sanctions? In a laboratory experiment we find that the answer is affirmative if the institution is imposed on the group but negative if development of the institution is left to the group to vote on. In the experiment, participants were divided into groups of either cooperative types or non-cooperative types depending on their behavior in a public goods game. In these homogeneous groups they repeatedly played a public goods game regulated by an institution that incorporated several of the key properties identified by Ostrom: operational rules, monitoring, rewards, punishments, and (in one condition change of rules. When change of rules was not possible and punishments were set to be high, groups of both types generally abided by operational rules demanding high contributions to the common good, and thereby achieved high levels of payoffs. Under less severe rules, both types of groups did worse but non-cooperative types did worst. Thus, non-cooperative groups profited the most from being governed by an institution demanding high contributions and employing high punishments. Nevertheless, in a condition where change of rules through voting was made possible, development of the institution in this direction was more often voted down in groups of non-cooperative types. We discuss the relevance of the hard problem and fit our results into a bigger picture of institutional and individual determinants of cooperative behavior.

  13. Fluorescent in situ hybridization (FISH) assessment of chromosome copy number in sperm

    Energy Technology Data Exchange (ETDEWEB)

    Sheu, M.; Sigman, M.; Mark, H.F.L. [Brown Univ. School of Medicine, Providence, RI (United States)

    1994-09-01

    Approximately 15% of all recognized pregnancies end in spontaneous abortions. The overall frequency of chromosome abnormalities in spontaneous abortions is approximately 50%. Thus aneuploidy is a significant cause of fetal wastage. In addition, structural and numerical abnormalities of chromosomes can also lead to birth defects, developmental delay, mental retardation and infertility. Conventional cytogenetic analysis via GTG- and other banding techniques is a powerful tool in the elucidation of the nature of chromosomal abnormalities. Fluorescent in situ hybridization (FISH) enables detection of numerical chromosomal abnormalities, especially trisomies, in intact cells. Using FISH and commercially available biotin-labeled probes, we have initiated a prospective study to assess specific chromosome copy number of preparations of unstained smears from men referred for a male infertility evaluation as well as smears from normal control males chosen randomly from the sample of sperm donors. A total of approximately 19,000 sperm nuclei have been examined thus far. Of those suitable for analysis, 7382 (38.75%) were normal possessing one copy of chromosome 8, 155 (0.81%) were disomic, and 15 (0.079%) had more than two copies of chromosome 8. Comparisons with data available in the literature will be discussed. Work is ongoing to increase the efficiency of hybridization using both reported and previously untried pretreatment and fixation protocols. We have also initiated studies using multicolor FISH with various chromosome enumeration probes. The assay described here is a potentially powerful tool for detecting rare events such as spontaneous germ cell aneuploidy, aneuploidy detected in semen from men with carcinoma in situ of the testis and aneuploidy induced by potential environmental genotoxicants. It can also be utilized for segregation analysis and for correlating chromosome copy number with germ cell morphology.

  14. Systematic hardness studies on lithium niobate crystals

    Indian Academy of Sciences (India)

    K G Subhadra; K Kishan Rao; D B Sirdeshmukh

    2000-04-01

    In view of discrepancies in the available information on the hardness of lithium niobate, a systematic study of the hardness has been carried out. Measurements have been made on two pure lithium niobate crystals with different growth origins, and a Fe-doped sample. The problem of load variation of hardness is examined in detail. The true hardness of LiNbO3 is found to be 630 ± 30 kg/mm2. The Fe-doped crystal has a larger hardness of 750 ± 50 kg/mm2.

  15. Hard Identity and Soft Identity

    Directory of Open Access Journals (Sweden)

    Hassan Rachik

    2006-04-01

    Full Text Available Often collective identities are classified depending on their contents and rarely depending on their forms. Differentiation between soft identity and hard identity is applied to diverse collective identities: religious, political, national, tribal ones, etc. This classification is made following the principal dimensions of collective identities: type of classification (univocal and exclusive or relative and contextual, the absence or presence of conflictsof loyalty, selective or totalitarian, objective or subjective conception, among others. The different characteristics analysed contribute to outlining an increasingly frequent type of identity: the authoritarian identity.

  16. Sampling hard to reach populations.

    Science.gov (United States)

    Faugier, J; Sargeant, M

    1997-10-01

    Studies on 'hidden populations', such as homeless people, prostitutes and drug addicts, raise a number of specific methodological questions usually absent from research involving known populations and less sensitive subjects. This paper examines the advantages and limitations of nonrandom methods of data collection such as snowball sampling. It reviews the currently available literature on sampling hard to reach populations and highlights the dearth of material currently available on this subject. The paper also assesses the potential for using these methods in nursing research. The sampling methodology used by Faugier (1996) in her study of prostitutes, HIV and drugs is used as a current example within this context.

  17. Radiation Hardness Assurance (RHA) Guideline

    Science.gov (United States)

    Campola, Michael J.

    2016-01-01

    Radiation Hardness Assurance (RHA) consists of all activities undertaken to ensure that the electronics and materials of a space system perform to their design specifications after exposure to the mission space environment. The subset of interests for NEPP and the REAG, are EEE parts. It is important to register that all of these undertakings are in a feedback loop and require constant iteration and updating throughout the mission life. More detail can be found in the reference materials on applicable test data for usage on parts.

  18. Thermopile detector radiation hard readout

    Science.gov (United States)

    Gaalema, Stephen; Van Duyne, Stephen; Gates, James L.; Foote, Marc C.

    2010-08-01

    The NASA Jupiter Europa Orbiter (JEO) conceptual payload contains a thermal instrument with six different spectral bands ranging from 8μm to 100μm. The thermal instrument is based on multiple linear arrays of thermopile detectors that are intrinsically radiation hard; however, the thermopile CMOS readout needs to be hardened to tolerate the radiation sources of the JEO mission. Black Forest Engineering is developing a thermopile readout to tolerate the JEO mission radiation sources. The thermal instrument and ROIC process/design techniques are described to meet the JEO mission requirements.

  19. Microstructure and hardness of WC-Co particle reinforced iron matrix surface composite

    OpenAIRE

    Zhang Peng; Zeng Shaolian; Zhang Zhiguo

    2013-01-01

    In this study, a high Cr cast iron surface composite material reinforced with WC-Co particles 2-6 mm in size was prepared using a pressureless sand mold infiltration casting technique. The composition, microstructure and hardness were determined by means of energy dispersive spectrometry (EDS), electron probe microanalysis (EPMA), scanning electron microscope (SEM) and Rockwell hardness measurements. It is determined that the obtained composite layer is about 15 mm thick with a WC-Co particle...

  20. Evolution vs the number of gene copies per primitive cell.

    Science.gov (United States)

    Koch, A L

    1984-01-01

    Computer simulations are presented of the rate at which an advantageous mutant would displace the prototype in a replicating system without an accurate segregation mechanism. If the number of gene copies in the system is indefinitely large, Darwinian evolution is essentially stopped because there is no coupling of phenotype with genotype, i.e., there is no growth advantage to the advantageous gene relative to the prototype and therefore no "survival of the fittest." The inhibition of evolution due to a number of gene copies less than 100 would have been not insurmountable. Although the presence of multiple copies would have allowed replacement by an advantageous mutant, it provided a way for the primitive cell to conserve less immediately useful genes that could evolve into different or more effective genes. This possibility was lost as accurate segregation mechanisms evolved and cells with few copies of each gene, such as modern procaryotes, arose.

  1. 7 CFR 46.42 - Copies of records; how obtained.

    Science.gov (United States)

    2010-01-01

    ... Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE MARKETING OF PERISHABLE AGRICULTURAL COMMODITIES REGULATIONS (OTHER THAN RULES OF PRACTICE) UNDER THE PERISHABLE AGRICULTURAL COMMODITIES ACT, 1930 Copies...

  2. Molecular methods for genotyping complex copy number polymorphisms.

    Science.gov (United States)

    Cantsilieris, Stuart; Baird, Paul N; White, Stefan J

    2013-02-01

    Genome structural variation shows remarkable complexity with respect to copy number, sequence content and distribution. While the discovery of copy number polymorphisms (CNP) has increased exponentially in recent years, the transition from discovery to genotyping has proved challenging, particularly for CNPs embedded in complex regions of the genome. CNPs that are collectively common in the population and possess a dynamic range of copy numbers have proved the most difficult to genotype in association studies. This is in some part due to technical limitations of genotyping assays and the sequence properties of the genomic region being analyzed. Here we describe in detail the basis of a number of molecular techniques used to genotype complex CNPs, compare and contrast these approaches for determination of multi-allelic copy number, and discuss the potential application of these techniques in genetic studies.

  3. Human copy number variation and complex genetic disease.

    Science.gov (United States)

    Girirajan, Santhosh; Campbell, Catarina D; Eichler, Evan E

    2011-01-01

    Copy number variants (CNVs) play an important role in human disease and population diversity. Advancements in technology have allowed for the analysis of CNVs in thousands of individuals with disease in addition to thousands of controls. These studies have identified rare CNVs associated with neuropsychiatric diseases such as autism, schizophrenia, and intellectual disability. In addition, copy number polymorphisms (CNPs) are present at higher frequencies in the population, show high diversity in copy number, sequence, and structure, and have been associated with multiple phenotypes, primarily related to immune or environmental response. However, the landscape of copy number variation still remains largely unexplored, especially for smaller CNVs and those embedded within complex regions of the human genome. An integrated approach including characterization of single nucleotide variants and CNVs in a large number of individuals with disease and normal genomes holds the promise of thoroughly elucidating the genetic basis of human disease and diversity.

  4. Intron analyses reveal multiple calmodulin copies in Littorina.

    Science.gov (United States)

    Simpson, R J; Wilding, C S; Grahame, J

    2005-04-01

    Intron 3 and the flanking exons of the calmodulin gene have been amplified, cloned, and sequenced from 18 members of the gastropod genus Littorina. From the 48 sequences, at least five different gene copies have been identified and their functionality characterized using a strategy based upon the potential protein product predicted from flanking exon data. The functionality analyses suggest that four of the genes code for functional copies of calmodulin. All five copies have been identified across a wide range of littorinid species although not ubiquitously. Using this novel approach based on intron sequences, we have identified an unprecedented number of potential calmodulin copies in Littorina, exceeding that reported for any other invertebrate. This suggests a higher number of, and more ancient, gene duplications than previously detected in a single genus.

  5. DNA replication stress restricts ribosomal DNA copy number.

    Science.gov (United States)

    Salim, Devika; Bradford, William D; Freeland, Amy; Cady, Gillian; Wang, Jianmin; Pruitt, Steven C; Gerton, Jennifer L

    2017-09-15

    Ribosomal RNAs (rRNAs) in budding yeast are encoded by ~100-200 repeats of a 9.1kb sequence arranged in tandem on chromosome XII, the ribosomal DNA (rDNA) locus. Copy number of rDNA repeat units in eukaryotic cells is maintained far in excess of the requirement for ribosome biogenesis. Despite the importance of the repeats for both ribosomal and non-ribosomal functions, it is currently not known how "normal" copy number is determined or maintained. To identify essential genes involved in the maintenance of rDNA copy number, we developed a droplet digital PCR based assay to measure rDNA copy number in yeast and used it to screen the yeast conditional temperature-sensitive mutant collection of essential genes. Our screen revealed that low rDNA copy number is associated with compromised DNA replication. Further, subculturing yeast under two separate conditions of DNA replication stress selected for a contraction of the rDNA array independent of the replication fork blocking protein, Fob1. Interestingly, cells with a contracted array grew better than their counterparts with normal copy number under conditions of DNA replication stress. Our data indicate that DNA replication stresses select for a smaller rDNA array. We speculate that this liberates scarce replication factors for use by the rest of the genome, which in turn helps cells complete DNA replication and continue to propagate. Interestingly, tumors from mini chromosome maintenance 2 (MCM2)-deficient mice also show a loss of rDNA repeats. Our data suggest that a reduction in rDNA copy number may indicate a history of DNA replication stress, and that rDNA array size could serve as a diagnostic marker for replication stress. Taken together, these data begin to suggest the selective pressures that combine to yield a "normal" rDNA copy number.

  6. Quantum copying and simplification of the quantum Fourier transform

    Science.gov (United States)

    Niu, Chi-Sheng

    Theoretical studies of quantum computation and quantum information theory are presented in this thesis. Three topics are considered: simplification of the quantum Fourier transform in Shor's algorithm, optimal eavesdropping in the BB84 quantum cryptographic protocol, and quantum copying of one qubit. The quantum Fourier transform preceding the final measurement in Shor's algorithm is simplified by replacing a network of quantum gates with one that has fewer and simpler gates controlled by classical signals. This simplification results from an analysis of the network using the consistent history approach to quantum mechanics. The optimal amount of information which an eavesdropper can gain, for a given level of noise in the communication channel, is worked out for the BB84 quantum cryptographic protocol. The optimal eavesdropping strategy is expressed in terms of various quantum networks. A consistent history analysis of these networks using two conjugate quantum bases shows how the information gain in one basis influences the noise level in the conjugate basis. The no-cloning property of quantum systems, which is the physics behind quantum cryptography, is studied by considering copying machines that generate two imperfect copies of one qubit. The best qualities these copies can have are worked out with the help of the Bloch sphere representation for one qubit, and a quantum network is worked out for an optimal copying machine. If the copying machine does not have additional ancillary qubits, the copying process can be viewed using a 2-dimensional subspace in a product space of two qubits. A special representation of such a two-dimensional subspace makes possible a complete characterization of this type of copying. This characterization in turn leads to simplified eavesdropping strategies in the BB84 and the B92 quantum cryptographic protocols.

  7. Supporting Teaching and Learning Via the Web: Transforming Hard-Copy Linear Mindsets into Web-Flexible Creative Thinking.

    Science.gov (United States)

    Borkowski, Ellen Yu; Henry, David; Larsen, Lida L.; Mateik, Deborah

    This paper describes a four-tiered approach to supporting University of Maryland faculty in the development of instructional materials to be delivered via the World Wide Web. The approach leverages existing equipment and staff by the design of Web posting, editing, and management tools for use on the campus-wide information server,…

  8. Hardness Measurement of (TiB2-TiAl)/TiAl Symmetrically Function Gradient Materials

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    (TiB2-TiAl)/TiAl symmetrically function gradient materials (FGM) were prepared by spark plasma sintering (SPS). Owing to the difference of the thermal expansion coefficients between TiB2 and TiAl, a compressive surface stress was introduced to the FGM by the thermal expansion mismatch. The hardness values of the uniform materials and the FGM were tested, respectively. For the FGM with a compressive surface stress, hardness is obviously superior to that of the uniform material.When the FGM was subjected to heat treatment,the hardness decreased due to a partial relaxation of the compressive surface stress.

  9. COPI complex is a regulator of lipid homeostasis.

    Directory of Open Access Journals (Sweden)

    Mathias Beller

    2008-11-01

    Full Text Available Lipid droplets are ubiquitous triglyceride and sterol ester storage organelles required for energy storage homeostasis and biosynthesis. Although little is known about lipid droplet formation and regulation, it is clear that members of the PAT (perilipin, adipocyte differentiation related protein, tail interacting protein of 47 kDa protein family coat the droplet surface and mediate interactions with lipases that remobilize the stored lipids. We identified key Drosophila candidate genes for lipid droplet regulation by RNA interference (RNAi screening with an image segmentation-based optical read-out system, and show that these regulatory functions are conserved in the mouse. Those include the vesicle-mediated Coat Protein Complex I (COPI transport complex, which is required for limiting lipid storage. We found that COPI components regulate the PAT protein composition at the lipid droplet surface, and promote the association of adipocyte triglyceride lipase (ATGL with the lipid droplet surface to mediate lipolysis. Two compounds known to inhibit COPI function, Exo1 and Brefeldin A, phenocopy COPI knockdowns. Furthermore, RNAi inhibition of ATGL and simultaneous drug treatment indicate that COPI and ATGL function in the same pathway. These data indicate that the COPI complex is an evolutionarily conserved regulator of lipid homeostasis, and highlight an interaction between vesicle transport systems and lipid droplets.

  10. Hard Fault Analysis of Trivium

    CERN Document Server

    Yupu, Hu; Yiwei, Zhang

    2009-01-01

    Fault analysis is a powerful attack to stream ciphers. Up to now, the major idea of fault analysis is to simplify the cipher system by injecting some soft faults. We call it soft fault analysis. As a hardware-oriented stream cipher, Trivium is weak under soft fault analysis. In this paper we consider another type of fault analysis of stream cipher, which is to simplify the cipher system by injecting some hard faults. We call it hard fault analysis. We present the following results about such attack to Trivium. In Case 1 with the probability not smaller than 0.2396, the attacker can obtain 69 bits of 80-bits-key. In Case 2 with the probability not smaller than 0.2291, the attacker can obtain all of 80-bits-key. In Case 3 with the probability not smaller than 0.2291, the attacker can partially solve the key. In Case 4 with non-neglectable probability, the attacker can obtain a simplified cipher, with smaller number of state bits and slower non-linearization procedure. In Case 5 with non-neglectable probability,...

  11. Nanomechanics of hard films on compliant substrates.

    Energy Technology Data Exchange (ETDEWEB)

    Reedy, Earl David, Jr. (Sandia National Laboratories, Albuquerque, NM); Emerson, John Allen (Sandia National Laboratories, Albuquerque, NM); Bahr, David F. (Washington State University, Pullman, WA); Moody, Neville Reid; Zhou, Xiao Wang; Hales, Lucas (University of Minnesota, Minneapolis, MN); Adams, David Price (Sandia National Laboratories, Albuquerque, NM); Yeager,John (Washington State University, Pullman, WA); Nyugen, Thao D. (Johns Hopkins University, Baltimore, MD); Corona, Edmundo (Sandia National Laboratories, Albuquerque, NM); Kennedy, Marian S. (Clemson University, Clemson, SC); Cordill, Megan J. (Erich Schmid Institute, Leoben, Austria)

    2009-09-01

    a result, our understanding of the critical relationship between adhesion, properties, and fracture for hard films on compliant substrates is limited. To address this issue, we integrated nanomechanical testing and mechanics-based modeling in a program to define the critical relationship between deformation and fracture of nanoscale films on compliant substrates. The approach involved designing model film systems and employing nano-scale experimental characterization techniques to isolate effects of compliance, viscoelasticity, and plasticity on deformation and fracture of thin hard films on substrates that spanned more than two orders of compliance magnitude exhibit different interface structures, have different adhesion strengths, and function differently under stress. The results of this work are described in six chapters. Chapter 1 provides the motivation for this work. Chapter 2 presents experimental results covering film system design, sample preparation, indentation response, and fracture including discussion on the effects of substrate compliance on fracture energies and buckle formation from existing models. Chapter 3 describes the use of analytical and finite element simulations to define the role of substrate compliance and film geometry on the indentation response of thin hard films on compliant substrates. Chapter 4 describes the development and application of cohesive zone model based finite element simulations to determine how substrate compliance affects debond growth. Chapter 5 describes the use of molecular dynamics simulations to define the effects of substrate compliance on interfacial fracture of thin hard tungsten films on silicon substrates. Chapter 6 describes the Workshops sponsored through this program to advance understanding of material and system behavior.

  12. Translation, copying and variation in two Castilian copies of the Epistola de cura rei familiaris by Pseudo Bernardus

    Directory of Open Access Journals (Sweden)

    Ruth Miguel Franco

    2011-12-01

    Full Text Available In this paper we attempt to analyse the differences between two copies, a printed exemplar (Burgos, Fadrique de Basilea c. 1495-1499 and a manuscript one (Madrid, BNE, 10445 of a Castilian translation of the Epistola de cura rei familiaris, a pseudo Bernardine tractate that belongs to the genre of the Oeconomica. Firstly, we will compare these two translations to a Latin copy of the Epistola printed by the same editor at around the same time. Secondly, we will compare the Castilian texts with one another in order to describe their main features. Last, on the basis of that description, we will try to distinguish between translation and copying mistakes, so that we are able to determine whether one of the Castilian texts may be a direct translation from Latin or whether both exemplars are copies of a former translation.

  13. A study of sound balances for the hard of hearing

    Science.gov (United States)

    Mathers, C. D.

    Over a period of years, complaints have been received from television viewers, especially those who are hard of hearing, that background sound (e.g., audience laughter, crowd noise, mood music) is often transmitted at too high a level with respect to speech, so that information essential to the understanding of the program is lost. To consider possible solutions to the problem, a working party was set up representing both broadcasters and organizations for the hard of hearing. At early meetings, it was resolved that a series of subjective tests should be carried out to determine what reduction of background levels would be needed to provide a significant improvement in the intelligibility of television speech for viewers with hearing difficulties. The preparation of test tapes and the analysis of results are given.

  14. Effects of the ratio of hardness to Young's modulus on the friction and wear behavior of bilayer coatings

    Science.gov (United States)

    Ni, Wangyang; Cheng, Yang-Tse; Lukitsch, Michael J.; Weiner, Anita M.; Lev, Lenoid C.; Grummon, David S.

    2004-11-01

    We present a study of the effects of the ratio of hardness to Young's modulus on the friction and wear behavior of layered composite coatings. Layered coating structures with the same surface coating but different interlayers were prepared by physical vapor deposition. We found that the ratio of hardness to Young's modulus plays an important role in determining the friction coefficient and wear resistance of layered composite coatings. A low friction coefficient and high wear resistance can be achieved in structures with high ratio of hardness to Young's modulus and moderately high hardness.

  15. Copy number variations exploration of multiple genes in Graves' disease.

    Science.gov (United States)

    Song, Rong-Hua; Shao, Xiao-Qing; Li, Ling; Wang, Wen; Zhang, Jin-An

    2017-01-01

    Few previous published papers reported copy number variations of genes could affect the predisposition of Graves' disease (GD). Herein, the aim of this study was to explore the association between copy number variations (CNV) profile and GD. The preliminary copy number microarray used to screen copy number variant genes was performed in 6 GD patients. Five CNV candidate genes (CFH, CFHR1, KIAA0125, UGT2B15, and UGT2B17) were then validated in an independent set of samples (50 GD patients and 50 matched healthy ones) by the Accucopy assay method. The CNV of the other 2 genes TRY6 and CCL3L1 was investigated in 144 GD patients and 144 healthy volunteers by the definitive genotyping technique using the Taqman quantitative polymerase-chain-reaction (Taqman qPCR). TRY6 gene-associated single nucleotide polymorphism (SNP), rs13230029, was genotyped by the PCR-ligase detection reaction (LDR) in 675 GD patients and 898 healthy controls. There were no correlation of the gene copy number (GCN) of CFH, CFHR1, KIAA0125, UGT2B15, and UGT2B17 with GD. In comparison with that of controls, the GCN distribution of TRY6 and CCL3L1 in GD patients did not show significantly differ (P > 0.05). Furthermore, TRY6-related polymorphism (rs13230029) showed no difference between GD patients and controls. No correlation was found between CNV or SNP genotype and clinical phenotypes. Generally, there were no link of the copy numbers of several genes, including CFH, CFHR1, KIAA0125, UGT2B15, UGT2B17, TRY6, and CCL3L1 to GD. Our results clearly indicated that the copy number variations of multiple genes, namely CFH, CFHR1, KIAA0125, UGT2B15, UGT2B17, TRY6, and CCL3L1, were not associated with the development of GD.

  16. Hard rock, heavy metal, metal

    OpenAIRE

    Hein, Fabien

    2011-01-01

    Le terme générique metal désigne une multitude de genres et de sous-genres musicaux issus de l’appariement du hard rock et du heavy metal. Il résulte d’une agrégation sémantique consécutive de l’érosion et de l’interpénétration de ces termes au cours des années 1980. Leurs modèles canoniques, respectivement représentés par les groupes Led Zeppelin et Black Sabbath, se sont progressivement dilués sous l’effet d’une filiation particulièrement effervescente et féconde : black, thrash, doom, prog...

  17. Probing Strangeness in Hard Processes

    CERN Document Server

    Avakian, H; Cisbani, E; Contalbrigo, M; D'Alesio, U; De Leo, R; Devita, R; Di Nezza, P; Hasch, D; Mirazita, M; Osipenko, M; Pappalardo, L; Rossi, P

    2012-01-01

    Since the discovery of strangeness almost five decades ago, interest in this degree of freedom has grown up and now its investigation spans the scales from quarks to nuclei. Measurements with identified strange hadrons can provide important information on several hot topics in hadronic physics: the strange distribution and fragmentation functions, the nucleon tomography and quark orbital momentum, accessible through the study of the {\\it generalized} parton distribution and the {\\it transverse momentum dependent} parton distribution functions, the quark hadronization in the nuclear medium, the hadron spectroscopy and the search for exotic mesons. The CLAS12 large acceptance spectrometer in Hall B at the Jefferson Laboratory upgraded with a RICH detector together with the 12 GeV CEBAF high intensity, high polarized electron beam can open new possibilities to study strangeness in hard processes allowing breakthroughs in all those areas. This paper summarizes the physics case for a RICH detector for CLAS12. Many...

  18. A hard case for modeling

    Directory of Open Access Journals (Sweden)

    George Marsh

    2002-10-01

    Some fighter pilots alive today owe their survival to tough, low-weight helmets whose qualities have been refined as a result of biomechanical modeling. Porter and his colleagues have modeled the human head as a mechanical arrangement of a heavy ball on a rod support, as a system of soft matter contained in a hard case, as an arrangement of meso-scale sub-systems, and as a combination of material systems built up from the nano-molecular and atomic scales. An extensive modeling hierarchy (Fig. 1 is held on nothing more esoteric than a networked workstation and server architecture. Nevertheless, thanks to a process of focused simplification at each hierarchical level, it is able to predict the mechanical behavior of the human head and its constituents in reacting to impacts with considerable accuracy.

  19. Schwannoma of the hard palate.

    Science.gov (United States)

    Isildak, Huseyin; Yilmaz, Mehmet; Ibrahimov, Metin; Aslan, Mehmet; Karaman, Emin; Enver, Ozgun

    2010-01-01

    About half of all neurogenic tumors are seen in the head and neck region. The types of neurogenic tumors must be distinguished. Schwannomas originate from Schwann cells of the neural sheath and are solitary, well-encapsulated, slow-growing adjacent to the parental nerve but extrinsic to the nerve fascicles.Approximately 25% to 45% of all schwannomas are seen in the head and neck region and are found rarely in the oral cavity. Most of the intraoral schwannomas are located in the tongue. Other less common locations are the buccal mucosa, palate, base of the mouth, gingiva, and lips.In this study, we report a rare case of schwannoma of the hard palate, which was excised intraorally.

  20. Synthesis and Characterization of Hot-Roll and Cold-Roll Byproduct-Derived Strontium Hard Ferrites

    Directory of Open Access Journals (Sweden)

    H. S. Woon

    2009-01-01

    Full Text Available Problem statement: Ceramic permanent magnets or more commonly known as strontium hexagonal ferrites have been widely used in permanent magnetic materials as they provide high remanence, high coercivity, relatively high energy product and good chemical stability. In this study, we treated factory byproduct from hot-roll and cold-roll steel industry was used as raw material in synthesis of strontium hexagonal hard ferrites. Approach: X-Ray Diffraction (XRD was employed to confirm the formation of strontium hard ferrite compound. Vibrating Sample Magnetometer (VSM was used to analyze the magnetic properties of samples prepared. Results: The magnetic properties, namely remanence and coercivity of factory byproduct-derived strontium hard ferrites were compared. The cold-roll-derived strontium hard ferrite showed higher remanence in this study. Conclusion: This implied that cold-roll byproduct was a better candidate to replace hematite in preparation of strontium hard ferrites compared to hot-roll byproduct.

  1. Hardware Assisted ROP Detection Mode (HARD Mode)

    Science.gov (United States)

    2013-08-01

    Distribution A. Cleared for public release; unlimited distribution. USAFA-CN-2013-457 Hardware Assisted ROP Detection Mode (HARD Mode) NATHANIEL HART...457 This report, "Hardware Assisted ROP Detection Mode (HARD Mode)" is presented as a competent treatment of the subj ect, worthy of publication. The...Technical 20120810-20121215 Hardware Assisted ROP Detection Mode (HARD Mode) NATHANIEL HART MICHAEL WINSTEAD MARTIN CARLISLE RODNEY LYKINS MICHAEL

  2. Hardness measures and resolution lower bounds

    OpenAIRE

    Beyersdorff, Olaf; Kullmann, Oliver

    2013-01-01

    Various "hardness" measures have been studied for resolution, providing theoretical insight into the proof complexity of resolution and its fragments, as well as explanations for the hardness of instances in SAT solving. In this report we aim at a unified view of a number of hardness measures, including different measures of width, space and size of resolution proofs. We also extend these measures to all clause-sets (possibly satisfiable).

  3. Unified characterisations of resolution hardness measures

    OpenAIRE

    Beyersdorff, O; Kullmann, O.

    2014-01-01

    Various "hardness" measures have been studied for resolution, providing theoretical insight into the proof complexity of resolution and its fragments, as well as explanations for the hardness of instances in SAT solving. In this paper we aim at a unified view of a number of hardness measures, including different measures of width, space and size of resolution proofs. Our main contribution is a unified game-theoretic characterisation of these measures. As consequences we obtain new relations b...

  4. Shock Waves in Dense Hard Disk Fluids

    OpenAIRE

    Sirmas, Nick; Tudorache, Marion; Barahona, Javier; Radulescu, Matei I.

    2011-01-01

    Media composed of colliding hard disks (2D) or hard spheres (3D) serve as good approximations for the collective hydrodynamic description of gases, liquids and granular media. In the present study, the compressible hydrodynamics and shock dynamics are studied for a two-dimensional hard-disk medium at both the continuum and discrete particle level descriptions. For the continuum description, closed form analytical expressions for the inviscid hydrodynamic description, shock Hugoniot, isentropi...

  5. Significant heterogeneity in Wolbachia copy number within and between populations of Onchocerca volvulus.

    Science.gov (United States)

    Armoo, Samuel; Doyle, Stephen R; Osei-Atweneboana, Mike Y; Grant, Warwick N

    2017-04-18

    Wolbachia are intracellular bacteria found in arthropods and several filarial nematode species. The filarial Wolbachia have been proposed to be involved in the immunopathology associated with onchocerciasis. Higher Wolbachia-to-nematode ratios have been reported in the savannah-ecotype compared to the forest-ecotype, and have been interpreted as consistent with a correlation between Wolbachia density and disease severity. However, factors such as geographic stratification and ivermectin drug exposure can lead to significant genetic heterogeneity in the nematode host populations, so we investigated whether Wolbachia copy number variation is also associated with these underlying factors. Genomic DNA was prepared from single adult nematodes representing forest and savannah ecotypes sampled from Togo, Ghana, Côte d'Ivoire and Mali. A qPCR assay was developed to measure the number of Wolbachia genome(s) per nematode genome. Next-generation sequencing (NGS) was also used to measure relative Wolbachia copy number, and independently verify the qPCR assay. Significant variation was observed within the forest (range: 0.02 to 452.99; median: 10.58) and savannah (range: 0.01 to 1106.25; median: 9.10) ecotypes, however, no significant difference between ecotypes (P = 0.645) was observed; rather, strongly significant Wolbachia variation was observed within and between the nine study communities analysed (P = 0.021), independent of ecotype. Analysis of ivermectin-treated and untreated nematodes by qPCR showed no correlation (P = 0.869); however, an additional analysis of a subset of the nematodes by qPCR and NGS revealed a correlation between response to ivermectin treatment and Wolbachia copy number (P = 0.020). This study demonstrates that extensive within and between population variation exists in the Wolbachia content of individual adult O. volvulus. The origin and functional significance of such variation (up to ~ 100,000-fold between worms; ~10 to 100

  6. Finding-specific display presets for computed radiography soft-copy reading.

    Science.gov (United States)

    Andriole, K P; Gould, R G; Webb, W R

    1999-05-01

    Much work has been done to optimize the display of cross-sectional modality imaging examinations for soft-copy reading (i.e., window/level tissue presets, and format presentations such as tile and stack modes, four-on-one, nine-on-one, etc). Less attention has been paid to the display of digital forms of the conventional projection x-ray. The purpose of this study is to assess the utility of providing presets for computed radiography (CR) soft-copy display, based not on the window/level settings, but on processing applied to the image optimized for visualization of specific findings, pathologies, etc (i.e., pneumothorax, tumor, tube location). It is felt that digital display of CR images based on finding-specific processing presets has the potential to: speed reading of digital projection x-ray examinations on soft copy; improve diagnostic efficacy; standardize display across examination type, clinical scenario, important key findings, and significant negatives; facilitate image comparison; and improve confidence in and acceptance of soft-copy reading. Clinical chest images are acquired using an Agfa-Gevaert (Mortsel, Belgium) ADC 70 CR scanner and Fuji (Stamford, CT) 9000 and AC2 CR scanners. Those demonstrating pertinent findings are transferred over the clinical picture archiving and communications system (PACS) network to a research image processing station (Agfa PS5000), where the optimal image-processing settings per finding, pathologic category, etc, are developed in conjunction with a thoracic radiologist, by manipulating the multiscale image contrast amplification (Agfa MUSICA) algorithm parameters. Soft-copy display of images processed with finding-specific settings are compared with the standard default image presentation for 50 cases of each category. Comparison is scored using a 5-point scale with the positive scale denoting the standard presentation is preferred over the finding-specific processing, the negative scale denoting the finding

  7. Food preference and copying behaviour in zebra finches, Taeniopygia guttata.

    Science.gov (United States)

    Guillette, Lauren M; Morgan, Kate V; Hall, Zachary J; Bailey, Ida E; Healy, Susan D

    2014-11-01

    As a social species zebra finches might be expected to copy the food choices of more experienced conspecifics. This prediction has been tested previously by presenting observers with two demonstrator birds that differ in some way (e.g., sex, familiarity), each feeding on a different colour food source. However, if the observer subsequently exhibits a preference, it is unclear whether it has copied the choice of one demonstrator or avoided the choice of the other. Furthermore, this choice may actually be influenced by pre-existing preferences, a potential bias that is rarely tested. Here we examine whether apparent copying or avoidance can be explained by pre-existing preferences. In Experiment 1, observers had the opportunity to watch a conspecific forage from one of the two differently coloured food hoppers. In Experiment 2, the observers did not have this opportunity. In both experiments observers were subsequently tested for their food hopper preference and all but one preferred one colour over the other. In Experiment 1 some observers showed evidence for copying, while others seemed to avoid the colour preferred by the demonstrator. In Experiment 2 females generally preferred the white hopper. Pre-existing colour preferences could, therefore, explain the apparent copying/avoidance we observed. This article is part of a Special Issue entitled: Cognition in the wild. Copyright © 2014 Elsevier B.V. All rights reserved.

  8. Endogenous RNA interference is driven by copy number

    Science.gov (United States)

    Cruz, Cristina; Houseley, Jonathan

    2014-01-01

    A plethora of non-protein coding RNAs are produced throughout eukaryotic genomes, many of which are transcribed antisense to protein-coding genes and could potentially instigate RNA interference (RNAi) responses. Here we have used a synthetic RNAi system to show that gene copy number is a key factor controlling RNAi for transcripts from endogenous loci, since transcripts from multi-copy loci form double stranded RNA more efficiently than transcripts from equivalently expressed single-copy loci. Selectivity towards transcripts from high-copy DNA is therefore an emergent property of a minimal RNAi system. The ability of RNAi to selectively degrade transcripts from high-copy loci would allow suppression of newly emerging transposable elements, but such a surveillance system requires transcription. We show that low-level genome-wide pervasive transcription is sufficient to instigate RNAi, and propose that pervasive transcription is part of a defense mechanism capable of directing a sequence-independent RNAi response against transposable elements amplifying within the genome. DOI: http://dx.doi.org/10.7554/eLife.01581.001 PMID:24520161

  9. Major copy proportion analysis of tumor samples using SNP arrays

    Directory of Open Access Journals (Sweden)

    Li Cheng

    2008-04-01

    Full Text Available Abstract Background Single nucleotide polymorphisms (SNPs are the most common genetic variations in the human genome and are useful as genomic markers. Oligonucleotide SNP microarrays have been developed for high-throughput genotyping of up to 900,000 human SNPs and have been used widely in linkage and cancer genomics studies. We have previously used Hidden Markov Models (HMM to analyze SNP array data for inferring copy numbers and loss-of-heterozygosity (LOH from paired normal and tumor samples and unpaired tumor samples. Results We proposed and implemented major copy proportion (MCP analysis of oligonucleotide SNP array data. A HMM was constructed to infer unobserved MCP states from observed allele-specific signals through emission and transition distributions. We used 10 K, 100 K and 250 K SNP array datasets to compare MCP analysis with LOH and copy number analysis, and showed that MCP performs better than LOH analysis for allelic-imbalanced chromosome regions and normal contaminated samples. The major and minor copy alleles can also be inferred from allelic-imbalanced regions by MCP analysis. Conclusion MCP extends tumor LOH analysis to allelic imbalance analysis and supplies complementary information to total copy numbers. MCP analysis of mixing normal and tumor samples suggests the utility of MCP analysis of normal-contaminated tumor samples. The described analysis and visualization methods are readily available in the user-friendly dChip software.

  10. Endogenous RNA interference is driven by copy number.

    Science.gov (United States)

    Cruz, Cristina; Houseley, Jonathan

    2014-02-11

    A plethora of non-protein coding RNAs are produced throughout eukaryotic genomes, many of which are transcribed antisense to protein-coding genes and could potentially instigate RNA interference (RNAi) responses. Here we have used a synthetic RNAi system to show that gene copy number is a key factor controlling RNAi for transcripts from endogenous loci, since transcripts from multi-copy loci form double stranded RNA more efficiently than transcripts from equivalently expressed single-copy loci. Selectivity towards transcripts from high-copy DNA is therefore an emergent property of a minimal RNAi system. The ability of RNAi to selectively degrade transcripts from high-copy loci would allow suppression of newly emerging transposable elements, but such a surveillance system requires transcription. We show that low-level genome-wide pervasive transcription is sufficient to instigate RNAi, and propose that pervasive transcription is part of a defense mechanism capable of directing a sequence-independent RNAi response against transposable elements amplifying within the genome. DOI: http://dx.doi.org/10.7554/eLife.01581.001.

  11. Potential health impacts of hard water

    National Research Council Canada - National Science Library

    Sengupta, Pallav

    2013-01-01

    ... the hardness of the drinking water. In addition, several epidemiological investigations have demonstrated the relation between risk for cardiovascular disease, growth retardation, reproductive failure, and other health problems...

  12. Secure Copier Which Allows Reuse Copied Documents with Sorting Capability in Accordance with Document Types

    OpenAIRE

    Kohei Arai

    2013-01-01

    Secure copy machine which allows reuse copied documents with sorting capability in accordance with the document types. Through experiments with a variety of document types, it is found that copied documents can be shared and stored in database in accordance with automatically classified document types securely. The copied documents are protected by data hiding based on wavelet Multi Resolution Analysis: MRA.

  13. Secure Copier Which Allows Reuse Copied Documents with Sorting Capability in Accordance with Document Types

    Directory of Open Access Journals (Sweden)

    Kohei Arai

    2013-09-01

    Full Text Available Secure copy machine which allows reuse copied documents with sorting capability in accordance with the document types. Through experiments with a variety of document types, it is found that copied documents can be shared and stored in database in accordance with automatically classified document types securely. The copied documents are protected by data hiding based on wavelet Multi Resolution Analysis: MRA.

  14. Mitochondrial DNA Copy Number in Sleep Duration Discordant Monozygotic Twins

    DEFF Research Database (Denmark)

    Wrede, Joanna E; Mengel-From, Jonas; Buchwald, Dedra

    2015-01-01

    STUDY OBJECTIVES: Mitochondrial DNA (mtDNA) copy number is an important component of mitochondrial function and varies with age, disease, and environmental factors. We aimed to determine whether mtDNA copy number varies with habitual differences in sleep duration within pairs of monozygotic twins....... SETTING: Academic clinical research center. PARTICIPANTS: 15 sleep duration discordant monozygotic twin pairs (30 twins, 80% female; mean age 42.1 years [SD 15.0]). DESIGN: Sleep duration was phenotyped with wrist actigraphy. Each twin pair included a "normal" (7-9 h/24) and "short" (sleeping...... twin. Fasting peripheral blood leukocyte DNA was assessed for mtDNA copy number via the n-fold difference between qPCR measured mtDNA and nuclear DNA creating an mtDNA measure without absolute units. We used generalized estimating equation linear regression models accounting for the correlated data...

  15. Genetically complex epilepsies, copy number variants and syndrome constellations.

    Science.gov (United States)

    Mefford, Heather C; Mulley, John C

    2010-10-05

    Epilepsy is one of the most common neurological disorders, with a prevalence of 1% and lifetime incidence of 3%. There are numerous epilepsy syndromes, most of which are considered to be genetic epilepsies. Despite the discovery of more than 20 genes for epilepsy to date, much of the genetic contribution to epilepsy is not yet known. Copy number variants have been established as an important source of mutation in other complex brain disorders, including intellectual disability, autism and schizophrenia. Recent advances in technology now facilitate genome-wide searches for copy number variants and are beginning to be applied to epilepsy. Here, we discuss what is currently known about the contribution of copy number variants to epilepsy, and how that knowledge is redefining classification of clinical and genetic syndromes.

  16. Candidate gene copy number analysis by PCR and multicapillary electrophoresis.

    Science.gov (United States)

    Szantai, Eszter; Elek, Zsuzsanna; Guttman, András; Sasvari-Szekely, Maria

    2009-04-01

    Genetic polymorphisms are often considered as risk factors of complex diseases serving as valuable and easily detectable biomarkers, also stable during the whole lifespan. A novel type of genetic polymorphism has been identified just recently, referred to as gene copy number variation (CNV) or copy number polymorphism. CNV of glycogen synthase kinase 3 beta and its adjacent gene, Nr1i2 (pregnane X receptor isoform), has been reported to associate with bipolar depression. In our study we introduced multicapillary electrophoresis for gene copy number analysis as an affordable alternative to real-time PCR quantification with TaqMan gene probes. Our results show the reliability of the developed method based on conventional PCR followed by separation of products by multicapillary electrophoresis with quantitative evaluation. This method can be readily implemented for the analysis of candidate gene CNVs in high throughput clinical laboratories and also in personalized medicine care of depression-related risk factors.

  17. Gribov horizon and Gribov copies effect in lattice Coulomb gauge

    CERN Document Server

    Burgio, Giuseppe; Reinhardt, Hugo; Vogt, Hannes

    2016-01-01

    Following a recent proposal by Cooper and Zwanziger we investigate via lattice simulations the effect on the Coulomb gauge propagators and on the Gribov-Zwanziger confinement mechanism of selecting the Gribov copy with the smallest non-trivial eigenvalue of the Faddeev-Popov operator, i.e. the one closest to the Gribov horizon. Although such choice of gauge drives the ghost propagator towards the prediction of continuum calculations, we find that it actually overshoots the goal. With increasing computer time, we observe that Gribov copies with arbitrarily small eigenvalues can be found. For such a method to work one would therefore need further restrictions on the gauge condition to isolate the physically relevant copies, since e.g. the Coulomb potential $V_C$ defined through the Faddeev-Popov operator becomes otherwise physically meaningless. Interestingly, the Coulomb potential alternatively defined through temporal link correlators is only marginally affected by the smallness of the eigenvalues.

  18. Number matters: control of mammalian mitochondrial DNA copy number.

    Science.gov (United States)

    Clay Montier, Laura L; Deng, Janice J; Bai, Yidong

    2009-03-01

    Regulation of mitochondrial biogenesis is essential for proper cellular functioning. Mitochondrial DNA (mtDNA) depletion and the resulting mitochondrial malfunction have been implicated in cancer, neurodegeneration, diabetes, aging, and many other human diseases. Although it is known that the dynamics of the mammalian mitochondrial genome are not linked with that of the nuclear genome, very little is known about the mechanism of mtDNA propagation. Nevertheless, our understanding of the mode of mtDNA replication has advanced in recent years, though not without some controversies. This review summarizes our current knowledge of mtDNA copy number control in mammalian cells, while focusing on both mtDNA replication and turnover. Although mtDNA copy number is seemingly in excess, we reason that mtDNA copy number control is an important aspect of mitochondrial genetics and biogenesis and is essential for normal cellular function.

  19. Genome wide copy number analysis of single cells

    Science.gov (United States)

    Baslan, Timour; Kendall, Jude; Rodgers, Linda; Cox, Hilary; Riggs, Mike; Stepansky, Asya; Troge, Jennifer; Ravi, Kandasamy; Esposito, Diane; Lakshmi, B.; Wigler, Michael; Navin, Nicholas; Hicks, James

    2016-01-01

    Summary Copy number variation (CNV) is increasingly recognized as an important contributor to phenotypic variation in health and disease. Most methods for determining CNV rely on admixtures of cells, where information regarding genetic heterogeneity is lost. Here, we present a protocol that allows for the genome wide copy number analysis of single nuclei isolated from mixed populations of cells. Single nucleus sequencing (SNS), combines flow sorting of single nuclei based on DNA content, whole genome amplification (WGA), followed by next generation sequencing to quantize genomic intervals in a genome wide manner. Multiplexing of single cells is discussed. Additionally, we outline informatic approaches that correct for biases inherent in the WGA procedure and allow for accurate determination of copy number profiles. All together, the protocol takes ~3 days from flow cytometry to sequence-ready DNA libraries. PMID:22555242

  20. Histotype-specific copy-number alterations in ovarian cancer

    Directory of Open Access Journals (Sweden)

    Huang Ruby YunJu

    2012-10-01

    Full Text Available Abstract Background Epithelial ovarian cancer is characterized by multiple genomic alterations; most are passenger alterations which do not confer tumor growth. Like many cancers, it is a heterogeneous disease and can be broadly categorized into 4 main histotypes of clear cell, endometrioid, mucinous, and serous. To date, histotype-specific copy number alterations have been difficult to elucidate. The difficulty lies in having sufficient sample size in each histotype for statistical analyses. Methods To dissect the heterogeneity of ovarian cancer and identify histotype-specific alterations, we used an in silico hypothesis-driven approach on multiple datasets of epithelial ovarian cancer. Results In concordance with previous studies on global copy number alterations landscape, the study showed similar alterations. However, when the landscape was de-convoluted into histotypes, distinct alterations were observed. We report here significant histotype-specific copy number alterations in ovarian cancer and showed that there is genomic diversity amongst the histotypes. 76 cancer genes were found to be significantly altered with several as potential copy number drivers, including ERBB2 in mucinous, and TPM3 in endometrioid histotypes. ERBB2 was found to have preferential alterations, where it was amplified in mucinous (28.6% but deleted in serous tumors (15.1%. Validation of ERBB2 expression showed significant correlation with microarray data (p=0.007. There also appeared to be reciprocal relationship between KRAS mutation and copy number alterations. In mucinous tumors where KRAS mutation is common, the gene was not significantly altered. However, KRAS was significantly amplified in serous tumors where mutations are rare in high grade tumors. Conclusions The study demonstrates that the copy number landscape is specific to the histotypes and identification of these alterations can pave the way for targeted drug therapy specific to the histotypes.

  1. Method for preparing ceramic composite

    Science.gov (United States)

    Alexander, Kathleen B.; Tiegs, Terry N.; Becher, Paul F.; Waters, Shirley B.

    1996-01-01

    A process for preparing ceramic composite comprising blending TiC particulates, Al.sub.2 O.sub.3 particulates and nickle aluminide and consolidating the mixture at a temperature and pressure sufficient to produce a densified ceramic composite having fracture toughness equal to or greater than 7 MPa m.sup.1/2, a hardness equal to or greater than 18 GPa.

  2. Chromosome Conformation Capture Carbon Copy (5C) in Budding Yeast.

    Science.gov (United States)

    Belton, Jon-Matthew; Dekker, Job

    2015-06-01

    Chromosome conformation capture carbon copy (5C) is a high-throughput method for detecting ligation products of interest in a chromosome conformation capture (3C) library. 5C uses ligation-mediated amplification (LMA) to generate carbon copies of 3C ligation product junctions using single-stranded oligonucleotide probes. This procedure produces a 5C library of short DNA molecules which represent the interactions between the corresponding restriction fragments. The 5C library can be amplified using universal primers containing the Illumina paired-end adaptor sequences for subsequent high-throughput sequencing.

  3. A quantum-copying machine for equatorial qubits

    OpenAIRE

    Fan, Heng; Wang, Xiang-Bin; Matsumoto, Keiji

    2000-01-01

    Bu\\v{z}ek and Hillery proposed a universal quantum-copying machine (UQCM) (i.e., transformation) to analyze the possibility of cloning arbitrary states. The UQCM copies quantum-mechanical states with the quality of its output does not depend on the input. We propose a slightly different transformation to analyze a restricted set of input states. We impose the conditions (I) the density matrices of the two output states are the same, and that (II) the distance between input density operator an...

  4. Copy-number variants in neurodevelopmental disorders: promises and challenges.

    LENUS (Irish Health Repository)

    Merikangas, Alison K

    2012-02-01

    Copy-number variation (CNV) is the most prevalent type of structural variation in the human genome. There is emerging evidence that copy-number variants (CNVs) provide a new vista on understanding susceptibility to neuropsychiatric disorders. Some challenges in the interpretation of current CNV studies include the use of overlapping samples, differing phenotypic definitions, an absence of population norms for CNVs and a lack of consensus in methods for CNV detection and analysis. Here, we review current CNV association study methods and results in autism spectrum disorders (ASD) and schizophrenia, and provide suggestions for design approaches to future studies that might maximize the translation of this work to etiological understanding.

  5. An Enhanced Approach to Detect Copy Move Forgery

    Directory of Open Access Journals (Sweden)

    Ruchita Singh

    2014-07-01

    Full Text Available Due to the enhancement in the availability and quality of image manipulation tools, it is easy for a forger to forge any image without living any traces of modification. Digital Image tampering is now-a-days very common. Most obvious practice for doing forgery is Copy Move Forgery. In this research, a novel approach to detect Copy Move forgery is proposed. In this approach block based method and feature based method is employed to extract features from the image and extracted features are than matched to detect forgery and also perform the localization of the Forged Regions in the Digital Image

  6. Quantum state discrimination using the minimum average number of copies

    CERN Document Server

    Slussarenko, Sergei; Li, Jun-Gang; Campbell, Nicholas; Wiseman, Howard M; Pryde, Geoff J

    2016-01-01

    In the task of discriminating between nonorthogonal quantum states from multiple copies, the key parameters are the error probability and the resources (number of copies) used. Previous studies have considered the task of minimizing the average error probability for fixed resources. Here we consider minimizing the average resources for a fixed admissible error probability. We derive a detection scheme optimized for the latter task, and experimentally test it, along with schemes previously considered for the former task. We show that, for our new task, our new scheme outperforms all previously considered schemes.

  7. Hard disks with SCSI interface

    CERN Document Server

    Denisov, O Yu

    1999-01-01

    The testing of 20 models of hard SCSI-disks is carried out: the Fujitsu MAE3091LP; the IBM DDRS-39130, DGHS-318220, DNES-318350, DRHS-36V and DRVS-18V; the Quantum Atlas VI 18.2; the Viking 11 9.1; the Seagate ST118202LW, ST118273LW, ST118273W, ST318203LW, ST318275LW, ST34520W, ST39140LW and ST39173W; and the Western Digital WDE9100-0007, WDE9100-AV0016, WDE9100-AV0030 and WDE9180-0048. All tests ran under the Windows NT 4.0 workstation operating system with Service Pack 4, under video mode with 1024*768 pixel resolution, 32- bit colour depth and V-frequency equal to 85 Hz. The detailed description and characteristics of SCSI stores are presented. Test results (ZD Winstone 99 and ZD WinBench 99 tests) are given in both table and diagram (disk transfer rate) forms. (0 refs).

  8. ERRATUM: Work smart, wear your hard hat

    CERN Multimedia

    2003-01-01

    An error appeared in the article «Work smart, wear your hard hat» published in Weekly Bulletin 27/2003, page 5. The impact which pierced a hole in the hard hat worn by Gerd Fetchenhauer was the equivalent of a box weighing 5 kg and not 50 kg.

  9. Retraction of Hard, Lozano, and Tversky (2006)

    Science.gov (United States)

    Hard, B. M.; Lozano, S. C.; Tversky, B.

    2008-01-01

    Reports a retraction of "Hierarchical encoding of behavior: Translating perception into action" by Bridgette Martin Hard, Sandra C. Lozano and Barbara Tversky (Journal of Experimental Psychology: General, 2006[Nov], Vol 135[4], 588-608). All authors retract this article. Co-author Tversky and co-author Hard believe that the research results cannot…

  10. Hard Spring Wheat Technical Committee 2016 Crop

    Science.gov (United States)

    Seven experimental lines of hard spring wheat were grown at up to five locations in 2016 and evaluated for kernel, milling, and bread baking quality against the check variety Glenn. Wheat samples were submitted through the Wheat Quality Council and processed and milled at the USDA-ARS Hard Red Spri...

  11. Numerical Solution of Hard-Core Mixtures

    OpenAIRE

    Buhot, Arnaud; Krauth, Werner

    1997-01-01

    We study the equilibrium phase diagram of binary mixtures of hard spheres as well as of parallel hard cubes. A superior cluster algorithm allows us to establish and to access the demixed phase for both systems and to investigate the subtle interplay between short-range depletion and long-range demixing.

  12. Aespoe Hard Rock Laboratory. Annual report 1998

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    The Aespoe Hard Rock Laboratory has been constructed as part of the preparations for the deep geological repository for spent nuclear fuel in Sweden. The Tracer Retention Understanding Experiments are made to gain a better understanding of radionuclide retention in the rock and create confidence in the radionuclide transport models that are intended to be used in the licensing of a deep repository for spent fuel. Experiments with sorbing radioactive tracers have been completed in a single fracture over a distance of about 5 m. These tests have been subject to blind predictions by the Aespoe Task Force on groundwater flow and transports of solutes. Breakthrough of sorbing tracers in the TRUE-I tests is retarded more strongly than would be expected based on laboratory data alone. Results are consistent for all tracers and tracer tests. The main objective of the TRUE Block Scale Experiment is to increase understanding and our ability to predict tracer transport in a fracture network over spatial scales of 10 to 50 m. The total duration of the project is approximately 4.5 years with a scheduled finish at the end of the year 2000. The REX project focuses on the reduction of oxygen in a repository after closure due to reactions with rock minerals and microbial activity. Results show that oxygen is consumed within a few days both for the field and laboratory experiments. The project Degassing of groundwater and two phase flow was initiated to improve our understanding of observations of hydraulic conditions made in drifts and interpretation of experiments performed close to drifts. The analysis performed so far shows that the experimentally observed flow reductions indeed are consistent with the degassing hypothesis. The Prototype Repository Test is focused on testing and demonstrating repository system function. A full-scale prototype including six deposition holes with canisters with electric heaters surrounded by highly compacted bentonite will be built and

  13. Hardness methods for testing maize kernels.

    Science.gov (United States)

    Fox, Glen; Manley, Marena

    2009-07-08

    Maize is a highly important crop to many countries around the world, through the sale of the maize crop to domestic processors and subsequent production of maize products and also provides a staple food to subsistance farms in undeveloped countries. In many countries, there have been long-term research efforts to develop a suitable hardness method that could assist the maize industry in improving efficiency in processing as well as possibly providing a quality specification for maize growers, which could attract a premium. This paper focuses specifically on hardness and reviews a number of methodologies as well as important biochemical aspects of maize that contribute to maize hardness used internationally. Numerous foods are produced from maize, and hardness has been described as having an impact on food quality. However, the basis of hardness and measurement of hardness are very general and would apply to any use of maize from any country. From the published literature, it would appear that one of the simpler methods used to measure hardness is a grinding step followed by a sieving step, using multiple sieve sizes. This would allow the range in hardness within a sample as well as average particle size and/or coarse/fine ratio to be calculated. Any of these parameters could easily be used as reference values for the development of near-infrared (NIR) spectroscopy calibrations. The development of precise NIR calibrations will provide an excellent tool for breeders, handlers, and processors to deliver specific cultivars in the case of growers and bulk loads in the case of handlers, thereby ensuring the most efficient use of maize by domestic and international processors. This paper also considers previous research describing the biochemical aspects of maize that have been related to maize hardness. Both starch and protein affect hardness, with most research focusing on the storage proteins (zeins). Both the content and composition of the zein fractions affect

  14. Surface hardness of different restorative materials after long-term immersion in sports and energy drinks.

    Science.gov (United States)

    Erdemir, Ugur; Yildiz, Esra; Eren, Meltem Mert; Ozel, Sevda

    2012-01-01

    The purpose of this study was to evaluate the effect of sports and energy drinks on the surface hardness of different restorative materials over a 6-month period. Forty-two disk-shaped specimens were prepared for each of the four restorative materials tested: Compoglass F, Filtek Z250, Filtek Supreme, and Premise. Specimens were immersed for 2 min daily, up to 6 months, in six storage solutions (n=7 per material for each solution): distilled water, Powerade, Gatorade, X-IR, Burn, and Red Bull. Surface hardness was measured at baseline, after 1 week, 1 month, and 6 months. Data were analyzed statistically using repeated measures ANOVA followed by the Bonferroni test for multiple comparisons (α=0.05). Surface hardness of the restorative materials was significantly affected by both immersion solution and immersion period (p<0.001). All tested solutions induced significant reduction in surface hardness of the restorative materials over a 6-month immersion period.

  15. Theoretical Hardness of Wurtzite-Structured Semiconductors

    Institute of Scientific and Technical Information of China (English)

    GUO Xiao-Ju; XU Bo; LIU Zhong-Yuan; YU Dong-Li; HE Ju-Long; GUO Li-Cong

    2008-01-01

    Vickers hardness calculations of eleven wurtzite-structured semiconductors are performed based on the microscopic hardness model All the parameters are obtained from first-principles calculations. There axe two types of chemical bonds in wurtzite-structured crystals. The overlap populations of the two types of chemical bonds in lonsdaleite are chosen as Pc for wurtzite structure. The calculated bond ionicity values of the wurtzite-structured semiconductors are in good agreement with the ionicities from the dielectric definition. When the hardness of wurtzite-structured crystal is higher than 20GPa, our calculated Vickers hardness is within 10% accuracy. Therefore, the hardness of novel wurtzite-structured crystal could be estimated from first-principles calculations.

  16. Hard magnetism in structurally engineered silica nanocomposite.

    Science.gov (United States)

    Song, Hyon-Min; Zink, Jeffrey I

    2016-09-21

    Creation of structural complexity by simple experimental control will be an attractive approach for the preparation of nanomaterials, as a classical bottom-up method is supplemented by a more efficient and more direct artificial engineering method. In this study, structural manipulation of MCM-41 type mesoporous silica is investigated by generating and imbedding hard magnetic CoFe2O4 nanoparticles into mesoporous silica. Depending on the heating rate and target temperature, mesoporous silica undergoes a transformation in shape to form hollow silica, framed silica with interior voids, or melted silica with intact mesostructures. Magnetism is governed by the major CoFe2O4 phase, and it is affected by antiferromagnetic hematite (α-Fe2O3) and olivine-type cobalt silicate (Co2SiO4), as seen in its paramagnetic behavior at the annealing temperature of 430 °C. The early formation of Co2SiO4 than what is usually observed implies the effect of the partial substitution of Fe in the sites of Co. Under slow heating (2.5 °C min(-1)) mesostructures are preserved, but with significantly smaller mesopores (d100 = 1.5 nm). In addition, nonstoichiometric CoxFe1-xO with metal vacancies at 600 °C, and spinel Co3O4 at 700 °C accompany major CoFe2O4. The amorphous nature of silica matrix is thought to contribute significantly to these structurally diverse and rich phases, enabled by off-stoichiometry between Si and O, and accelerated by the diffusion of metal cations into SiO4 polyhedra at an elevated temperature.

  17. DETERMINATION OF THE OPTIMAL TEMPERING TEMPERATURE IN HARD FACING OF THE FORGING DIES

    Directory of Open Access Journals (Sweden)

    Milan Mutavdžić

    2012-06-01

    Full Text Available Here is analyzed selection of the optimal technology for heat treatment during the reparation of the damaged forging dies. Those tools are manufactured from alloyed tool steels for operation at elevated temperatures. Those steels are prone to self-hardening, so in reparatory hard-facing they must be preheated, additionally heated and tempered. During the tempering, in temperature interval 500-600°C, a secondary increase of hardness and decrease of impact toughness occurs, the so-called reversible tempering brittleness. Here is shown that it can be avoided by application of metallurgical and technological measures. Metallurgical measures assume adequate selection of steels. Since the considered steels are per se prone to tempering brittleness, we conducted experimental investigations to define the technological measures to avoid it. Tests on models were conducted: tempering from different temperatures, slow heating and cooling in still air. Hardness measurements showed that at 520°C, the secondary increase of hardness occurs, with drop of the impact toughness. Additional hard-facing tests included samples tempered at various regimes. Samples were prepared for mechanical and metallographic investigations. Results presented illustrate influence of additional heat treatment on structure, hardness and mechanical properties of the hard-faced layers. This enabled establishing the possibility of avoiding the tempering brittleness through technological measures.

  18. Determination of the optimal tempering temperature in hard facing of the forging dies

    Directory of Open Access Journals (Sweden)

    Milan Mutavdžić

    2012-05-01

    Full Text Available Here is analyzed selection of the optimal technology for heat treatment during the reparation of the damaged forging dies. Those tools are manufactured from alloyed tool steels for operation at elevated temperatures. Those steels are prone to self-hardening, so in reparatory hard-facing they must be preheated, additionally heated and tempered. During the tempering, in temperature interval 500-600°C, a secondary increase of hardness and decrease of impact toughness occurs, the so-called reversible tempering brittleness. Here is shown that it can be avoided by application of metallurgical and technological measures. Metallurgical measures assume adequate selection of steels. Since the considered steels are per se prone to tempering brittleness, we conducted experimental investigations to define the technological measures to avoid it. Tests on models were conducted: tempering from different temperatures, slow heating and cooling in still air. Hardness measurements showed that at 520°C, the secondary increase of hardness occurs, with drop of the impact toughness. Additional hard-facing tests included samples tempered at various regimes. Samples were prepared for mechanical and metallographic investigations. Results presented illustrate influence of additional heat treatment on structure, hardness and mechanical properties of the hard-faced layers. This enabled establishing the possibility of avoiding the tempering brittleness through technological measures. 

  19. Genomic Copy Number Variation in Disorders of Cognitive Development

    Science.gov (United States)

    Morrow, Eric M.

    2010-01-01

    Objective: To highlight recent discoveries in the area of genomic copy number variation in neuropsychiatric disorders including intellectual disability, autism, and schizophrenia. To emphasize new principles emerging from this area, involving the genetic architecture of disease, pathophysiology, and diagnosis. Method: Review of studies published…

  20. Single-copy insertion of transgenes in Caenorhabditis elegans

    DEFF Research Database (Denmark)

    Frøkjaer-Jensen, Christian; Davis, M Wayne; Hopkins, Christopher E;

    2008-01-01

    At present, transgenes in Caenorhabditis elegans are generated by injecting DNA into the germline. The DNA assembles into a semistable extrachromosomal array composed of many copies of injected DNA. These transgenes are typically overexpressed in somatic cells and silenced in the germline. We have...

  1. The blessing effect of an extra copy of chromosome 21

    African Journals Online (AJOL)

    Solaf M. Elsayed

    2014-02-25

    Feb 25, 2014 ... The protective effect of the extra copy of chromosome against the ... genesis by decreasing the vascular endothelial growth factor. C (VEGF-C) levels in .... [8] Sun Y, Wang J, Liu Y, Song X, Zhang Y, Li K, et al. Results of.

  2. Copy number variations in affective disorders and meta-analysis

    DEFF Research Database (Denmark)

    Olsen, Line; Hansen, Thomas; Djurovic, Srdjan

    2011-01-01

    In two recent studies 10 copy number variants (CNV) were found to be overrepresented either among patients suffering from affective disorders in an Amish family or in the Wellcome Trust Case-Control Consortium study. Here, we investigate if these variants are associated with affective disorders...

  3. Content-based video copy detection benchmarking at TRECVID

    NARCIS (Netherlands)

    Awad, G.; Over, P.; Kraaij, W.

    2014-01-01

    This article presents an overview of the video copy detection benchmarkwhichwas run over a period of 4 years (2008-2011) as part of the TREC Video Retrieval (TRECVID) workshop series. The main contributions of the article include i) an examination of the evolving design of the evaluation framework

  4. Using Copy Change with Trade Books to Teach Earth Science

    Science.gov (United States)

    Bintz, William P.; Wright, Pam; Sheffer, Julie

    2010-01-01

    Developing and implementing relevant, challenging, integrative, and exploratory curriculum is critical at all levels of schooling. This article describes one attempt to develop and implement an instance of interdisciplinary curriculum by using copy change with trade books to teach earth science. Specifically, it introduces trade books as a way to…

  5. Advertising Copy: Short Route to the Argumentative Essay.

    Science.gov (United States)

    Brown, Stephen G.

    1994-01-01

    Describes how generating effective advertising copy affords students practice in aspects of persuasive writing, such as developing a thesis, refuting counter-arguments, and writing in a comparison-contrast mode. Notes that this approach helps students negotiate the problematic shift from expressive to persuasive discourse without losing their…

  6. From Copy-and-Paste to Trace-and-Learn

    DEFF Research Database (Denmark)

    Klitgård, Ida

    2009-01-01

    of them even use the term ‹copy-and-paste› to illustrate this, suggesting that their perception is closely linked to their use of the internet. This generally one-dimensional perception calls for immediate repair work in the teaching of English academic writing in International Study Programmes...

  7. Evidence for nonconscious behavior-copying in young children

    NARCIS (Netherlands)

    Schaik, J.E. van; Baaren, R.B. van; Bekkering, H.; Hunnius, S.

    2013-01-01

    Behavioral mimicry is the nonconscious copying of an interaction partner’s behavior and is affected by social dynamics. Whereas it has been studied extensively in adults, little is known about the development of mimicry. The aims of this study were twofold, first to identify whether young children

  8. Chimpanzees copy dominant and knowledgeable individuals: implications for cultural diversity.

    Science.gov (United States)

    Kendal, Rachel; Hopper, Lydia M; Whiten, Andrew; Brosnan, Sarah F; Lambeth, Susan P; Schapiro, Steven J; Hoppitt, Will

    2015-01-01

    Evolutionary theory predicts that natural selection will fashion cognitive biases to guide when, and from whom, individuals acquire social information, but the precise nature of these biases, especially in ecologically valid group contexts, remains unknown. We exposed four captive groups of chimpanzees (Pan troglodytes) to a novel extractive foraging device and, by fitting statistical models, isolated four simultaneously operating transmission biases. These include biases to copy (i) higher-ranking and (ii) expert individuals, and to copy others when (iii) uncertain or (iv) of low rank. High-ranking individuals were relatively un-strategic in their use of acquired knowledge, which, combined with the bias for others to observe them, may explain reports that high innovation rates (in juveniles and subordinates) do not generate a correspondingly high frequency of traditions in chimpanzees. Given the typically low rank of immigrants in chimpanzees, a 'copying dominants' bias may contribute to the observed maintenance of distinct cultural repertoires in neighboring communities despite sharing similar ecology and knowledgeable migrants. Thus, a copying dominants strategy may, as often proposed for conformist transmission, and perhaps in concert with it, restrict the accumulation of traditions within chimpanzee communities whilst maintaining cultural diversity.

  9. Using Copy Change with Trade Books to Teach Earth Science

    Science.gov (United States)

    Bintz, William P.; Wright, Pam; Sheffer, Julie

    2010-01-01

    Developing and implementing relevant, challenging, integrative, and exploratory curriculum is critical at all levels of schooling. This article describes one attempt to develop and implement an instance of interdisciplinary curriculum by using copy change with trade books to teach earth science. Specifically, it introduces trade books as a way to…

  10. 7 CFR 3601.2 - Public inspection, copying, and indexing.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Public inspection, copying, and indexing. 3601.2 Section 3601.2 Agriculture Regulations of the Department of Agriculture (Continued) NATIONAL AGRICULTURAL... indexing. 5 U.S.C. 552(a)(2) requires that certain materials be made available for public inspection...

  11. Bovine copy number variation and its implication in animal health

    Science.gov (United States)

    Recently it has become apparent that previously unappreciated genomic structural variation, including copy number variations (CNV), contributes significantly to individual health and disease in humans and rodents. As a complement to the bovine HapMap project, we initiated a systematic study of the C...

  12. From Copy-and-Paste to Trace-and-Learn

    DEFF Research Database (Denmark)

    Klitgård, Ida

    2009-01-01

    This paper presents an investigation of both Danish and international second-semester BA-students' perceptions of the problem of plagiarism. Surprisingly, the investigation proves that the students unanimously perceive plagiarism as directly copying other people's texts or entire works. Some...

  13. European Union. European Commission: Private Copying Recommendations Following Stakeholder Mediation

    NARCIS (Netherlands)

    J.P. Quintais

    2013-01-01

    Private copying levies are a constant topic of debate in EU copyright law and policy. They have been on the harmonization agenda since the 1988 Green Paper on Copyright and the Challenge of Technology and, following stakeholder consultations (in 2006 and 2008) and the 2011 IPR Strategy, remain an on

  14. 36 CFR 1290.6 - Originals and copies.

    Science.gov (United States)

    2010-07-01

    ... Section 1290.6 Parks, Forests, and Public Property NATIONAL ARCHIVES AND RECORDS ADMINISTRATION JFK... ASSASSINATION RECORDS COLLECTION ACT OF 1992 (JFK ACT) § 1290.6 Originals and copies. (a) For purposes of.... Kennedy Assassination Records Collection (JFK Assassination Records Collection) established under the...

  15. Factors Affecting Early Services for Children Who Are Hard of Hearing

    Science.gov (United States)

    Harrison, Melody; Page, Thomas A.; Oleson, Jacob; Spratford, Meredith; Berry, Lauren Unflat; Peterson, Barbara; Welhaven, Anne; Arenas, Richard M.; Moeller, Mary Pat

    2016-01-01

    Purpose: To describe factors affecting early intervention (EI) for children who are hard of hearing, we analyzed (a) service setting(s) and the relationship of setting to families' frequency of participation, and (b) provider preparation, caseload composition, and experience in relation to comfort with skills that support spoken language for…

  16. Copy Number Variation at the APOL1 Locus.

    Directory of Open Access Journals (Sweden)

    Rupam Ruchi

    Full Text Available Two coding variants in the APOL1 gene (G1 and G2 explain most of the high rate of kidney disease in African Americans. APOL1-associated kidney disease risk inheritance follows an autosomal recessive pattern: The relative risk of kidney disease associated with inheritance of two high-risk variants is 7-30 fold, depending on the specific kidney phenotype. We wished to determine if the variability in phenotype might in part reflect structural differences in APOL1 gene. We analyzed sequence coverage from 1000 Genomes Project Phase 3 samples as well as exome sequencing data from African American kidney disease cases for copy number variation. 8 samples sequenced in the 1000 Genomes Project showed increased coverage over a ~100kb region that includes APOL2, APOL1 and part of MYH9, suggesting the presence of APOL1 copy number greater than 2. We reasoned that such duplications should be enriched in apparent G1 heterozygotes with kidney disease. Using a PCR-based assay, we observed the presence of this duplication in additional samples from apparent G0G1 or G0G2 individuals. The frequency of this APOL1 duplication was compared among cases (n = 123 and controls (n = 255 with apparent G0G1 heterozygosity. The presence of APOL1 duplication was observed in 4.06% of cases and 0.78% controls, preliminary evidence that this APOL1 duplication may alter susceptibility to kidney disease (p = 0.03. Taqman-based copy number assays confirmed the presence of 3 APOL1 copies in individuals positive for this specific duplication by PCR assay, but also identified a small number of individuals with additional APOL1 copies of presumably different structure. These observations motivate further studies to better assess the contribution of APOL1 copy number on kidney disease risk and on APOL1 function. Investigators and clinicians genotyping APOL1 should also consider whether the particular genotyping platform used is subject to technical errors when more than two copies of

  17. Copy-number and gene dependency analysis reveals partial copy loss of wild-type SF3B1 as a novel cancer vulnerability. | Office of Cancer Genomics

    Science.gov (United States)

    Genomic instability is a hallmark of human cancer, and results in widespread somatic copy number alterations. We used a genome-scale shRNA viability screen in human cancer cell lines to systematically identify genes that are essential in the context of particular copy-number alterations (copy-number associated gene dependencies). The most enriched class of copy-number associated gene dependencies was CYCLOPS (Copy-number alterations Yielding Cancer Liabilities Owing to Partial losS) genes, and spliceosome components were the most prevalent.

  18. Degradation of mitochondrial DNA in cryoprotectant-treated hard coral (Echinopora spp.) oocytes.

    Science.gov (United States)

    Tsai, Sujune; Chen, Jiann-Chu; Spikings, Emma; Li, Jan-Jung; Lin, Chiahsin

    2015-06-01

    A critical step for successful cryopreservation is to determine the optimal cryoprotectant treatment that can provide protective effects against cryoinjury during freezing and with minimal toxicity. Most cryoprotectants have chemical and osmotic effects when used at high concentrations. Cryoprotectants can damage coral mitochondrial distributions and membrane potentials, which results in reduced ATP production. As mitochondrial DNA (mtDNA) encodes for components of the electron transport chain (ETC) and plays a critical role in ATP synthesis capacity, we determined the effects of cryoprotectants on mtDNA in hard coral (Echinopora spp.) oocytes using quantitative real-time PCR. Our results showed that an insult from a cryoprotectant may be compensated for by the genetic defense mechanisms of these cells. Methanol was found to have the least effect on coral oocytes with regard to their energy status. A single oocyte without cryoprotectant treatment produced an average of 4,220,645 ± 169,990 mtDNA copies, which was greater than that in mammals. However, relatively lower mtDNA copy numbers (<2,000,000) were observed when oocytes were treated with dimethyl sulfoxide (DMSO), propylene glycol (PG), ethylene glycol (EG), or glycerol at a concentration of 3 M for 20 min. These results provide direct evidence that hard coral (Echinopora spp.) oocytes are extremely susceptible to cryoprotectants and support the concerns with regard to the adverse effects of cryoprotectants.

  19. Fundamentals and hard-switching converters

    CERN Document Server

    Ioinovici, Adrian

    2013-01-01

    Volume 1 Fundamentals and Hard-switching Converters introduces the key challenges in power electronics from basic components to operation principles and presents classical hard- and soft-switching DC to DC converters, rectifiers and inverters. At a more advanced level, it provides comprehensive analysis of DC and AC models comparing the available approaches for their derivation and results. A full treatment of DC to DC hard-switching converters is given, from fundamentals to modern industrial solutions and practical engineering insight. The author elucidates various contradictions and misunderstandings in the literature, for example, in the treatment of the discontinuous conduction operation or in deriving AC small-signal models of converters.

  20. Analytic studies of the hard dumbell fluid

    Science.gov (United States)

    Morriss, G. P.; Cummings, P. T.

    A closed form analytic theory for the structure of the hard dumbell fluid is introduced and evaluated. It is found to be comparable in accuracy to the reference interaction site approximation (RISA) of Chandler and Andersen.

  1. Why Are Drugs So Hard to Quit?

    Medline Plus

    Full Text Available ... it free Find out why Close Why Are Drugs So Hard to Quit? National Institute on Drug Abuse (NIDA/NIH) Loading... Unsubscribe from National Institute on Drug Abuse (NIDA/NIH)? Cancel Unsubscribe Working... Subscribe Subscribed ...

  2. Why Are Drugs So Hard to Quit?

    Medline Plus

    Full Text Available ... navigation Sign in Search Loading... Close Yeah, keep it Undo Close This video is unavailable. Watch Queue ... changes the signals in your brain and makes it hard to feel OK without the drug. This ...

  3. Radiation Hard High Performance Optoelectronic Devices Project

    Data.gov (United States)

    National Aeronautics and Space Administration — High-performance, radiation-hard, widely-tunable integrated laser/modulator chip and large-area avalanche photodetectors (APDs) are key components of optical...

  4. Why Are Drugs So Hard to Quit?

    Medline Plus

    Full Text Available ... Feb 7, 2012 Quitting drugs is hard because addiction is a brain disease. Your brain is like ... out signals to direct your actions and choices. Addiction changes the signals in your brain and makes ...

  5. Event Driven Langevin simulations of Hard Spheres

    CERN Document Server

    Scala, Antonio

    2011-01-01

    The blossoming of interest in colloids and nano-particles has given renewed impulse to the study of hard-body systems. In particular, hard spheres have become a real test system for theories and experiments. It is therefore necessary to study the complex dynamics of such systems in presence of a solvent; disregarding hydrodynamic interactions, the simplest model is the Langevin equation. Unfortunately, standard algorithms for the numerical integration of the Langevin equation require that interactions are slowly varying during an integration timestep. This in not the case for hard-body systems, where there is no clearcut between the correlation time of the noise and the timescale of the interactions. Starting first from a splitting of the Fokker-Plank operator associated with the Langevin dynamics, and then from an approximation of the two-body Green's function, we introduce and test two new algorithms for the simulation of the Langevin dynamics of hard-spheres.

  6. Hard target LIDAR calibration for SO2

    CSIR Research Space (South Africa)

    Du Plessis, A

    2006-01-01

    Full Text Available Presentation on hard target LIDAR calibration for SO2. This project aimed at measuring the concentration of the atmospheric pollutants such as gases and mobile laser system for remote detection...

  7. Why Are Drugs So Hard to Quit?

    Medline Plus

    Full Text Available ... later? Sign in to add this video to a playlist. Sign in Share More Report Need to ... 2012 Quitting drugs is hard because addiction is a brain disease. Your brain is like a control ...

  8. Optical waveguides in hard crystalline materials

    NARCIS (Netherlands)

    Pollnau, M.

    2005-01-01

    The recent results of our research group and collaborators in the field of fabrication, characterization, and applications of optical waveguides in hard crystalline materials, specifically in sapphire and Ti:sapphire, are reviewed.

  9. Why Is It So Hard to Quit?

    Science.gov (United States)

    ... to quit? It’s hard to tackle the physical addiction to nicotine . Cigarettes contain nicotine, a highly addictive ... a support group can give you comfort and positive reinforcement. Cut back on caffeine . Caffeine is a ...

  10. FTIR STUDIES ON THE MODEL POLYURETHANE HARD SEGMENTS BASED ON A NEW WATERBORNE CHAIN EXTENDER DIMETHYLOL BUTANOIC ACID (DMBA)

    Institute of Scientific and Technical Information of China (English)

    Zhi-yong Ren; Hai-ping Wu; Jian-ming Ma; De-zhu Ma

    2004-01-01

    Three model polyurethane hard segments based on dimethylol butanoic acid (DMBA) and 1,6-hexane diisocyanate (HDI), toluene diisocyanate (TDI) and 4,4'-diphenylmethane diisocyanate (MDI) were prepared by the solution method.Fourier Infrared (FTIR) spectroscopy was employed to study the H-bonds in these model polyurethanes. The model polyurethane hard segment prepared from HDI and 1,4-butanodiol (BDO) was used for comparison. It was found that the H-bond but gives more H-bond patterns based on the two H-bond donors, urethane NH and carboxylic OH. The carboxylic aromatic model hard segments is stronger than that of aliphatic hard segments. The appearance of the free C = O and the fact that almost all N-H is H-bonded suggest that there possibly exist either the third H-bond acceptor or the H-bond formed by one acceptor with two donors.

  11. Standard test methods for rockwell hardness of metallic materials

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2011-01-01

    1.1 These test methods cover the determination of the Rockwell hardness and the Rockwell superficial hardness of metallic materials by the Rockwell indentation hardness principle. This standard provides the requirements for Rockwell hardness machines and the procedures for performing Rockwell hardness tests. 1.2 This standard includes additional requirements in annexes: Verification of Rockwell Hardness Testing Machines Annex A1 Rockwell Hardness Standardizing Machines Annex A2 Standardization of Rockwell Indenters Annex A3 Standardization of Rockwell Hardness Test Blocks Annex A4 Guidelines for Determining the Minimum Thickness of a Test Piece Annex A5 Hardness Value Corrections When Testing on Convex Cylindrical Surfaces Annex A6 1.3 This standard includes nonmandatory information in appendixes which relates to the Rockwell hardness test. List of ASTM Standards Giving Hardness Values Corresponding to Tensile Strength Appendix X1 Examples of Procedures for Determining Rockwell Hardness Uncertainty Appendix X...

  12. Standard test methods for rockwell hardness of metallic materials

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2008-01-01

    1.1 These test methods cover the determination of the Rockwell hardness and the Rockwell superficial hardness of metallic materials by the Rockwell indentation hardness principle. This standard provides the requirements for Rockwell hardness machines and the procedures for performing Rockwell hardness tests. 1.2 This standard includes additional requirements in annexes: Verification of Rockwell Hardness Testing Machines Annex A1 Rockwell Hardness Standardizing Machines Annex A2 Standardization of Rockwell Indenters Annex A3 Standardization of Rockwell Hardness Test Blocks Annex A4 Guidelines for Determining the Minimum Thickness of a Test Piece Annex A5 Hardness Value Corrections When Testing on Convex Cylindrical Surfaces Annex A6 1.3 This standard includes nonmandatory information in appendixes which relates to the Rockwell hardness test. List of ASTM Standards Giving Hardness Values Corresponding to Tensile Strength Appendix X1 Examples of Procedures for Determining Rockwell Hardness Uncertainty Appendix X...

  13. Hardness and Methods to Solve CLIQUE

    Institute of Scientific and Technical Information of China (English)

    ZHU Daming; LUAN Junfeng; MA Shaohan

    2001-01-01

    The paper briefly reviews NP-hard optimization problems and their inapproximability. The hardness of solving CLIQUE problem is specifically discussed. A dynamic-programming algorithm and its improved version for CLIQUE are reviewed and some additional analysis is presented. The analysis implies that the improved algorithm, HEWN (hierarchical edge-weighted network), only provides a heuristic or useful method, but cannot be called a polynomial algorithm.

  14. A Novel Approach to Hardness Testing

    Science.gov (United States)

    Spiegel, F. Xavier; West, Harvey A.

    1996-01-01

    This paper gives a description of the application of a simple rebound time measuring device and relates the determination of relative hardness of a variety of common engineering metals. A relation between rebound time and hardness will be sought. The effect of geometry and surface condition will also be discussed in order to acquaint the student with the problems associated with this type of method.

  15. The Chiral Dipolar Hard Sphere Model.

    OpenAIRE

    Mazars, Martial

    2009-01-01

    Abstract A simple molecular model of chiral molecules is presented in this paper : the chiral dipolar hard sphere model. The discriminatory interaction between enantiomers is represented by electrostatic (or magnetic) dipoles-dipoles interactions : short ranged steric repulsion are represented by hard sphere potential and, in each molecule, two point dipoles are located inside the sphere. The model is described in detail and some of its elementary properties are given ; in particul...

  16. Point defects in hard-sphere crystals

    OpenAIRE

    Pronk, S.; Frenkel, D.

    2001-01-01

    We report numerical calculations of the concentration of interstitials in hard-sphere crystals. We find that, in a three-dimensional fcc hard-sphere crystal at the melting point, the concentration of interstitials is 2 * 10^-8. This is some three orders of magnitude lower than the concentration of vacancies. A simple, analytical estimate yields a value that is in fair agreement with the numerical results.

  17. Animal Models of Psychiatric Disorders That Reflect Human Copy Number Variation

    Directory of Open Access Journals (Sweden)

    Jun Nomura

    2012-01-01

    Full Text Available The development of genetic technologies has led to the identification of several copy number variations (CNVs in the human genome. Genome rearrangements affect dosage-sensitive gene expression in normal brain development. There is strong evidence associating human psychiatric disorders, especially autism spectrum disorders (ASDs and schizophrenia to genetic risk factors and accumulated CNV risk loci. Deletions in 1q21, 3q29, 15q13, 17p12, and 22q11, as well as duplications in 16p11, 16p13, and 15q11-13 have been reported as recurrent CNVs in ASD and/or schizophrenia. Chromosome engineering can be a useful technology to reflect human diseases in animal models, especially CNV-based psychiatric disorders. This system, based on the Cre/loxP strategy, uses large chromosome rearrangement such as deletion, duplication, inversion, and translocation. Although it is hard to reflect human pathophysiology in animal models, some aspects of molecular pathways, brain anatomy, cognitive, and behavioral phenotypes can be addressed. Some groups have created animal models of psychiatric disorders, ASD, and schizophrenia, which are based on human CNV. These mouse models display some brain anatomical and behavioral abnormalities, providing insight into human neuropsychiatric disorders that will contribute to novel drug screening for these devastating disorders.

  18. Hard and Soft Multilayered SiCN Nanocoatings with High Hardness and Toughness

    Directory of Open Access Journals (Sweden)

    S. K. Mishra

    2013-01-01

    Full Text Available Alternate hard and soft layers increase deformation accommodation as thin hard layers slide relative to each other due to shear deformation of low modulus layers. However, the processing of such multilayers is challenging. In the present paper the alternating soft and hard multilayered SiCN coating deposited by magnetron sputtering has been studied and presented. A hardness and modulus of 37 GPa and 317 GPa with elastic recovery of 62% are achieved by alternate hard and soft layer of Si–C–N by magnetron sputtering. The trilayer films sustained even 2000 gf under indentation without failure though substrate plastically deformed. The fracture toughness value KIC was measured to be 9.5–10 MPa m1/2, significantly higher than many reported hard coatings.

  19. What does motor efference copy represent? Evidence from speech production.

    Science.gov (United States)

    Niziolek, Caroline A; Nagarajan, Srikantan S; Houde, John F

    2013-10-09

    How precisely does the brain predict the sensory consequences of our actions? Efference copy is thought to reflect the predicted sensation of self-produced motor acts, such as the auditory feedback heard while speaking. Here, we use magnetoencephalographic imaging (MEG-I) in human speakers to demonstrate that efference copy prediction does not track movement variability across repetitions of the same motor task. Specifically, spoken vowels were less accurately predicted when they were less similar to a speaker's median production, even though the prediction is thought to be based on the very motor commands that generate each vowel. Auditory cortical responses to less prototypical speech productions were less suppressed, resembling responses to speech errors, and were correlated with later corrective movement, suggesting that the suppression may be functionally significant for error correction. The failure of the motor system to accurately predict less prototypical speech productions suggests that the efferent-driven suppression does not reflect a sensory prediction, but a sensory goal.

  20. COPY – MOVE IMAGE FORGERY DETECTION IN A PARALLEL ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    M.Sridevi

    2012-07-01

    Full Text Available Image forgery is the manipulation of digital images to conceal meaningful information or objects in the image. Among different image forgery techniques, copy – move forgery is one of the frequently used passive image forgery approach. The existing methods such as Principle Component Analysis (PCA, Discrete Wavelet Transform (DWT & Singular Value Decomposition (SVD are time consuming. Hence it is not suited for digital forensic science, surveillance system applications which uses image, video or multimedia security. This paper proposes a parallel algorithm for the copy – move image forgery detection to decrease execution time of the algorithm. The method uses overlapping blocks and lexicographical sorting in a parallel manner. The simulation results show that the proposed parallel version detects the forged region faster, so that it is best suited for real time applications.

  1. Electromagnetic fields, size, and copy of a single photon

    CERN Document Server

    Liu, Shan-Liang

    2016-01-01

    We propose the expressions of electromagnetic fields of a single photon which properly describe the known characteristics of a photon, derive the relations between the photon size and wavelength on basis of the expressions, reveal the differences between a photon and its copy, and give the specific expressions of annihilation and creation operators of a photon. The results show that a photon has length of half the wavelength, and its radius is proportional to square root of the wavelength; a photon and its copy have the phase difference of {\\pi} and constitute a phase-entangled state; the N-photon phase-entangled state, which is formed by the sequential stimulated emission and corresponds to the wave train in optics, is not a coherent state, but it is the eigenstate of the number operator of photons.

  2. Research on copying system of dynamic multiplex holographic stereograms

    Science.gov (United States)

    Fu, Huaiping; Yang, Hong; Zheng, Tong

    2003-05-01

    The most important advantage of holographic stereograms over conventional hologram is that they can produce 3D images at any desired scale with movement, holographers in many countries involved in the studies towards it. We began our works in the early 80's and accomplished two research projects automatic system for making synthetic holograms and multiplex synthetic rainbow holograms, Based on these works, a large scale holographic stereogram of an animated goldfish was made by us for practical advertisement. In order to meet the needs of the market, a copying system for making multiplex holographic stereograms, and a special kind of silver halide holographic film developed by us recently. The characteristic of the copying system and the property of the special silver-halide emulsion are introduced in this paper.

  3. Building Hot Snapshot Copy Based on Windows File System

    Institute of Scientific and Technical Information of China (English)

    WANG Lina; GUO Chi; WANG Dejun; ZHU Qin

    2006-01-01

    This paper describes a method for building hot snapshot copy based on windows-file system (HSCF). The architecture and running mechanism of HSCF are discussed after giving a comparison with other on-line backup technology. HSCF, based on a file system filter driver, protects computer data and ensures their integrity and consistency with following three steps:access to open files, synchronization and copy-on-write. Its strategies for improving system performance are analyzed including priority setting, incremental snapshot and load balance. HSCF is a new kind of snapshot technology to solve the data integrity and consistency problem in online backup, which is different from other storage-level snapshot and Open File Solution.

  4. Perceiving the impossible: how individuals with autism copy paradoxical figures.

    Science.gov (United States)

    Sheppard, Elizabeth; Ropar, Danielle; Mitchell, Peter

    2009-07-01

    Mottron and colleagues found that individuals with autism were less affected by geometric impossibility than comparison participants on a copying task. The current experiment sought to determine whether a local perceptual style could account for this. Participants with and without autism copied possible and impossible geometric figures. Geometric impossibility had a larger effect on drawing time for comparison participants than for those with autism. However, participants with autism did not use more localized drawing strategies. Strength of impossibility effect was associated with a global strategy amongst comparison participants but this relationship was not found amongst participants with autism. The findings suggest that differences in high-level conceptual processing may account for group differences in effects of impossibility.

  5. The copying power of one-state tree transducers

    DEFF Research Database (Denmark)

    Engelfriet, Joost; Skyum, Sven

    1982-01-01

    One-state deterministic top-down tree transducers (or, tree homomorphisms) cannot handle “prime copying,” i.e., their class of output (string) languages is not closed under the operation L → {$(w$)f(n) short parallel w ε L, f(n) greater-or-equal, slanted 1}, where f is any integer function whose...... range contains numbers with arbitrarily large prime factors (such as a polynomial). The exact amount of nonclosure under these copying operations is established for several classes of input (tree) languages. These results are relevant to the extended definable (or, restricted parallel level) languages......, to the syntax-directed translation of context-free languages, and to the tree transducer hierarchy....

  6. Analysis of the Multi-Phase Copying Garbage Collection Algorithm

    Energy Technology Data Exchange (ETDEWEB)

    Podhorszki, Norbert [ORNL

    2009-01-01

    The multi-phase copying garbage collection was designed to avoid the need for large amount of reserved memory usually required for the copying types of garbage collection algorithms. The collection is performed in multiple phases using the available free memory. This paper proves that the number of phases depends on the size of the reserved memory and the ratio of the garbage and accessible objects. The performance of the implemented algorithm is tested in a fine-grained parallel Prolog system. We find that reserving only 10% of memory for garbage collection is sufficient for good performance in practice. Additionally, an improvement of the generic algorithm specifically for the tested parallel Prolog system is described.

  7. Alternatives for hard chromium plating: Nanostructured coatings for severe-service valves

    Energy Technology Data Exchange (ETDEWEB)

    Vernhes, L. [Department of Engineering Physics, Ecole Polytechnique, C.P. 6079, Succ. Centre Ville, Montreal, Quebec, Canada H3C 3A7 (Canada); Velan Inc., 7007 Côte de Liesse, Montreal, Quebec, Canada H4T 1X8 (Canada); Azzi, M. [Department of Mechanical Engineering, Notre Dame University-Louize (Lebanon); Klemberg-Sapieha, J.E., E-mail: jsapieha@polymtl.ca [Department of Engineering Physics, Ecole Polytechnique, C.P. 6079, Succ. Centre Ville, Montreal, Quebec, Canada H3C 3A7 (Canada)

    2013-07-15

    In this paper, a variety of chromium-free protective coatings were evaluated as alternatives for hard chromium (HC) electroplating for valve applications, such as nanostructured cobalt-phosphor (NCP) deposited by electroplating and tungsten/tungsten carbide (W/WC) prepared by chemical vapor deposition. A series of laboratory tests including hardness, micro scratch, pin-on-disk and electrochemical polarization measurements were performed in order to compare the performance of the different coatings. In addition, mechanical resistance and fatigue resistance were evaluated using prototype valves with coated ball under severe tribo-corrosion conditions. It was shown that W/WC coating exhibits superior resistance to wear and corrosion due to high hardness and high resistance to pitting, respectively while NCP exhibits better wear resistance than HC with alumina ball and low corrosion potential which allow to use it as protective (sacrificial) coating. Both nanostructured coatings exhibited attractive tribo-mechanical and functional characteristics compared to hard chromium. - Highlights: • Tungsten/tungsten carbide (W/WC) and cobalt-phosphor (NCP) coatings are compared with hard chromium (HC). • NCP and W/WC offer better tribological properties (wear rate and friction coefficient) than HC. • W/WC has demonstrated a robust corrosion behavior with a breakdown potential greater than 1 V. • NCP and W/WC are potential candidates to replace hard chromium as protective coating.

  8. Developing and Studying the Methods of Hard-Facing with Heat-Resisting High-Hardness Steels

    Science.gov (United States)

    Malushin, N. N.; Kovalev, A. P.; Valuev, D. V.; Shats, E. A.; Borovikov, I. F.

    2016-08-01

    The authors develop the methods of hard-facing of mining-metallurgic equipment parts with heat-resisting high-hardness steels on the base of plasma-jet hard-facing in the shielding-alloying nitrogen atmosphere.

  9. Genome Architecture and Its Roles in Human Copy Number Variation

    Directory of Open Access Journals (Sweden)

    Lu Chen

    2014-12-01

    Full Text Available Besides single-nucleotide variants in the human genome, large-scale genomic variants, such as copy number variations (CNVs, are being increasingly discovered as a genetic source of human diversity and the pathogenic factors of diseases. Recent experimental findings have shed light on the links between different genome architectures and CNV mutagenesis. In this review, we summarize various genomic features and discuss their contributions to CNV formation. Genomic repeats, including both low-copy and high-copy repeats, play important roles in CNV instability, which was initially known as DNA recombination events. Furthermore, it has been found that human genomic repeats can also induce DNA replication errors and consequently result in CNV mutations. Some recent studies showed that DNA replication timing, which reflects the high-order information of genomic organization, is involved in human CNV mutations. Our review highlights that genome architecture, from DNA sequence to high-order genomic organization, is an important molecular factor in CNV mutagenesis and human genomic instability.

  10. Mate-choice copying as Bayesian decision making.

    Science.gov (United States)

    Uehara, Takashi; Yokomizo, Hiroyuki; Iwasa, Yo

    2005-03-01

    Mate-choice copying by females has been reported in fishes (e.g., guppies) and lekking birds. Presumably, females assess males' quality using both information from direct observation of males and information acquired by observing other females' choices. Here, we study mathematically the conditions under which mate-choice copying is advantageous on the basis of Bayesian decision theory. A female may observe the mate choice of another female, called the model female, who has performed an optimal choice based on her own judgment. The conditions required for the focal female to choose the same mate as that chosen by the model female should depend on the male's appearance to her, the reliability of her own judgment of male quality, and the reliability of the model females. When three or more females are involved, the optimal mate choice critically depends on whether multiple model females make decisions independently or they themselves copy the choices of others. If two equally reliable females choose different males, the choice of the second female, made knowing the choice of the first, should have a stronger effect on the choice of the third (focal) female. This "last-choice precedence" should be tested experimentally.

  11. Copy number variation of KIR genes influences HIV-1 control

    DEFF Research Database (Denmark)

    Pelak, Kimberly; Need, Anna C; Fellay, Jacques

    2011-01-01

    A genome-wide screen for large structural variants showed that a copy number variant (CNV) in the region encoding killer cell immunoglobulin-like receptors (KIR) associates with HIV-1 control as measured by plasma viral load at set point in individuals of European ancestry. This CNV encompasses...... the KIR3DL1-KIR3DS1 locus, encoding receptors that interact with specific HLA-Bw4 molecules to regulate the activation of lymphocyte subsets including natural killer (NK) cells. We quantified the number of copies of KIR3DS1 and KIR3DL1 in a large HIV-1 positive cohort, and showed that an increase in KIR3...... individuals with multiple copies of KIR3DL1, in the presence of KIR3DS1 and the appropriate ligands, inhibit HIV-1 replication more robustly, and associated with a significant expansion in the frequency of KIR3DS1+, but not KIR3DL1+, NK cells in their peripheral blood. Our results suggest that the relative...

  12. Large multi-allelic copy number variations in humans

    Science.gov (United States)

    Handsaker, Robert E.; Van Doren, Vanessa; Berman, Jennifer R.; Genovese, Giulio; Kashin, Seva; Boettger, Linda M.; McCarroll, Steven A.

    2015-01-01

    Thousands of genome segments appear to be present in widely varying copy number in different human genomes. We developed ways to use increasingly abundant whole genome sequence data to identify the copy numbers, alleles and haplotypes present at most large, multi-allelic CNVs (mCNVs). We analyzed 849 genomes sequenced by the 1000 Genomes Project to identify most large (>5 kb) mCNVs, including 3,878 duplications, of which 1,356 appear to have three or more segregating alleles. We find that mCNVs give rise to most human gene-dosage variation – exceeding sevenfold the contribution of deletions and biallelic duplications – and that this variation in gene dosage generates abundant variation in gene expression. We describe “runaway duplication haplotypes” in which genes, including HPR and ORM1, have mutated to high copy number on specific haplotypes. We describe partially successful initial strategies for analyzing mCNVs via imputation and provide an initial data resource to support such analyses. PMID:25621458

  13. A Method for Calling Copy Number Polymorphism Using Haplotypes

    Directory of Open Access Journals (Sweden)

    Gun Ho eJang

    2013-09-01

    Full Text Available Single nucleotide polymorphism (SNP and copy number variation (CNV are both widespread characteristic of the human genome, but are often called separately on common genotyping platforms. To capture integrated SNP and CNV information, methods have been developed for calling allelic specific copy numbers or so called copy number polymorphism (CNP, using limited inter-marker correlation. In this paper, we proposed a haplotype-based maximum likelihood method to call CNP, which takes advantage of the valuable multi-locus linkage disequilibrium (LD information in the population. We also developed a computationally efficient EM algorithm to estimate haplotype frequencies and optimize individual CNP calls simultaneously, even at presence of missing data. Through simulations, we demonstrated our model is more sensitive and accurate in detecting various CNV regions, compared with commonly-used CNV calling methods including PennCNV, another hidden Markov model using CNP, a scan statistic, segCNV, and cnvHap. Our method often performs better in the regions with higher LD, in longer CNV regions, and in common CNV than the opposite. We implemented our method on the genotypes of 90 HapMap CEU samples and 23 patients with acute lung injury (ALI. For each ALI patient the genotyping was performed twice. The CNPs from our method show good consistency and accuracy comparable to others.

  14. Mechanism by Which Magnesium Oxide Suppresses Tablet Hardness Reduction during Storage.

    Science.gov (United States)

    Sakamoto, Takatoshi; Kachi, Shigeto; Nakamura, Shohei; Miki, Shinsuke; Kitajima, Hideaki; Yuasa, Hiroshi

    2016-01-01

    This study investigated how the inclusion of magnesium oxide (MgO) maintained tablet hardness during storage in an unpackaged state. Tablets were prepared with a range of MgO levels and stored at 40°C with 75% relative humidity for up to 14 d. The hardness of tablets prepared without MgO decreased over time. The amount of added MgO was positively associated with tablet hardness and mass from an early stage during storage. Investigation of the water sorption properties of the tablet components showed that carmellose water sorption correlated positively with the relative humidity, while MgO absorbed and retained moisture, even when the relative humidity was reduced. In tablets prepared using only MgO, a petal- or plate-like material was observed during storage. Fourier transform infrared spectrophotometry showed that this material was hydromagnesite, produced when MgO reacts with water and CO2. The estimated level of hydromagnesite at each time-point showed a significant negative correlation with tablet porosity. These results suggested that MgO suppressed storage-associated softening by absorbing moisture from the environment. The conversion of MgO to hydromagnesite results in solid bridge formation between the powder particles comprising the tablets, suppressing the storage-related increase in volume and increasing tablet hardness.

  15. Soft Skills for Hard Impact

    Science.gov (United States)

    Grigorov, Ivo; Davidson, Joy; Knoth, Petr; Kuchma, Iryna; Schmidt, Birgit; Rettberg, Najla; Rogrigues, Eloy

    2015-04-01

    Marine and Earth Science graduates will be under increasing pressure in future to delve into research questions of relevance to societal challenges. Even fundamental research focused on basic processes of the environment and universe will in the coming decade need to justify their societal impact. As the Research Excellence Frameworks (REF) for research evaluation shift more and more away from the classical Impact Factor and number of peer-reviewed publications to "societal impact", the question remains whether the current graduates, and future researchers, are sufficiently prepared to deal with this reality. The essential compliment of skills beyond research excellence, rigor and method are traditionally described as "soft skills". This includes how to formulate an argument, how to construct a scientific publication, how to communicate such publications to non-experts, place them in context of societal challenges and relevant policies, how to write a competitive proposal and "market" one's research idea to build a research group around an interesting research topic. Such "soft skills" can produce very measurable and concrete impact for career development, but are rarely provided systematically and coherently by graduate schools in general. The presentation will focus on Open Science as a set of "soft skills", and demonstrate why graduate schools should train Open Science competencies alongside research excellence by default. Open Science is about removing all barriers to research process and outputs, both published and unpublished, and directly supports transparency and reproducibility of the research process. Open Science as a set of news competencies can also foster unexpected collaborations, engage citizen scientists into co-creation of solutions to societal challenges, as well as use concepts of Open Science to transfer new knowledge to the knowledge-based private sector, and help them with formulating more competitive research proposals in future.

  16. Cyanobacteria Maintain Constant Protein Concentration despite Genome Copy-Number Variation.

    Science.gov (United States)

    Zheng, Xiao-Yu; O'Shea, Erin K

    2017-04-18

    The cyanobacterium Synechococcus elongatus PCC 7942 has multiple copies of its single chromosome, and the copy number varies in individual cells, providing an ideal system to study the effect of genome copy-number variation on cell size and gene expression. Using single-cell fluorescence imaging, we found that protein concentration remained constant across individual cells regardless of genome copy number. Cell volume and the total protein amount from a single gene were both positively, linearly correlated with genome copy number, suggesting that changes in cell volume play an important role in buffering genome copy-number variance. This study provides a quantitative examination of gene expression regulation in cells with variable genome copies and sheds light on the compensation mechanisms for variance in genome copy number. Copyright © 2017 The Author(s). Published by Elsevier Inc. All rights reserved.

  17. Shape-Memory Properties of Segmented Polymers Containing Aramid Hard Segments and Polycaprolactone Soft Segments

    Directory of Open Access Journals (Sweden)

    Arno Kraft

    2010-06-01

    Full Text Available A series of segmented multiblock copolymers containing aramid hard segments and extended polycaprolactone soft segments (with an Mn of 4,200 or 8,200 g mol–1 was prepared and tested for their shape-memory properties. Chain extenders were essential to raise the hard segment concentration so that an extended rubbery plateau could be observed. Dynamic mechanical thermal analysis provided a useful guide in identifying (i the presence of a rubbery plateau, (ii the flow temperature, and (iii the temperature when samples started to deform irreversibly.

  18. Evaluating the cooking process for obtaining hard candy from araza (Eugenia stipitata) pulp

    OpenAIRE

    Eduardo Rodríguez Sandoval; Patricia Bastidas Garzón

    2010-01-01

    This work was aimed at preparing hard candy from arazá (a fruit tree from the Amazon rainforest) using a sugar solution consis- ting of glucose syrup and invert sugar; this was cooked with fruit pulp to concentrate it. Temperature, time, soluble solids and vis- cosity were measured when cooking the mixture. Heat transfer was studied in an agitated steam jacketed kettle using the expe- rimental data. The best arazá hard candy formulation consisted of 15% fruit pulp, 2% pectin regarding the ...

  19. Solution preparation

    Energy Technology Data Exchange (ETDEWEB)

    Seitz, M.G.

    1982-01-01

    Reviewed in this statement are methods of preparing solutions to be used in laboratory experiments to examine technical issues related to the safe disposal of nuclear waste from power generation. Each approach currently used to prepare solutions has advantages and any one approach may be preferred over the others in particular situations, depending upon the goals of the experimental program. These advantages are highlighted herein for three approaches to solution preparation that are currently used most in studies of nuclear waste disposal. Discussion of the disadvantages of each approach is presented to help a user select a preparation method for his particular studies. Also presented in this statement are general observations regarding solution preparation. These observations are used as examples of the types of concerns that need to be addressed regarding solution preparation. As shown by these examples, prior to experimentation or chemical analyses, laboratory techniques based on scientific knowledge of solutions can be applied to solutions, often resulting in great improvement in the usefulness of results.

  20. Evaluation of the image quality of ink-jet printed paper copies of digital chest radiographs as compared with film: a receiver operating characteristic study.

    Science.gov (United States)

    Lyttkens, K; Kirkhorn, T; Kehler, M; Andersson, B; Ebbesen, A; Hochbergs, P; Jarlman, O; Lindberg, C G; Holmer, N G

    1994-05-01

    Paper copies of digital radiographs printed with the continuous ink-jet technique have proved to be of a high enough quality for demonstration purposes. We present a study on the image quality of ink-jet printed paper copies of digital chest radiographs, based on receiver operating characteristic (ROC) analysis. Eighty-three digital radiographs of a chest phantom with simulated tumors in the mediastinum and right lung, derived from a computed radiography (CR) system were presented in two series of hard copies as ink-jet printed paper copies and as laser recorded film. The images, with a matrix of 1,760 x 2,140 pixels, were printed with a spatial resolution of 10 pixels/mm in the CR film recorder as well as in the ink-jet printer. On film, every image was recorded in two versions, one optimized for the mediastinum and one for the lungs. On paper, only one image was printed; this constituted an effort to optimize both the mediastinum and the lungs. The ink-jet printed images, printed on a matt coated paper, were viewed as on-sight images with reflected light. The examinations were reviewed by six radiologists, and ROC curves were constructed. No significant difference was found between the performance of film and that of ink-jet paper prints. Because the cost for a paper copy is only a tenth of that of film, remarkable cost reductions can be achieved by using the ink jet technique instead. Our results show that further quality studies of ink-jet printed images are worthwhile.

  1. An integrated Bayesian analysis of LOH and copy number data

    Directory of Open Access Journals (Sweden)

    Hutter Marcus

    2010-06-01

    Full Text Available Abstract Background Cancer and other disorders are due to genomic lesions. SNP-microarrays are able to measure simultaneously both genotype and copy number (CN at several Single Nucleotide Polymorphisms (SNPs along the genome. CN is defined as the number of DNA copies, and the normal is two, since we have two copies of each chromosome. The genotype of a SNP is the status given by the nucleotides (alleles which are present on the two copies of DNA. It is defined homozygous or heterozygous if the two alleles are the same or if they differ, respectively. Loss of heterozygosity (LOH is the loss of the heterozygous status due to genomic events. Combining CN and LOH data, it is possible to better identify different types of genomic aberrations. For example, a long sequence of homozygous SNPs might be caused by either the physical loss of one copy or a uniparental disomy event (UPD, i.e. each SNP has two identical nucleotides both derived from only one parent. In this situation, the knowledge of the CN can help in distinguishing between these two events. Results To better identify genomic aberrations, we propose a method (called gBPCR which infers the type of aberration occurred, taking into account all the possible influence in the microarray detection of the homozygosity status of the SNPs, resulting from an altered CN level. Namely, we model the distributions of the detected genotype, given a specific genomic alteration and we estimate the parameters involved on public reference datasets. The estimation is performed similarly to the modified Bayesian Piecewise Constant Regression, but with improved estimators for the detection of the breakpoints. Using artificial and real data, we evaluate the quality of the estimation of gBPCR and we also show that it outperforms other well-known methods for LOH estimation. Conclusions We propose a method (gBPCR for the estimation of both LOH and CN aberrations, improving their estimation by integrating both types

  2. High-resolution copy number arrays in cancer and the problem of normal genome copy number variation.

    Science.gov (United States)

    Gorringe, Kylie L; Campbell, Ian G

    2008-11-01

    High-resolution techniques for analysis of genome copy number (CN) enable the analysis of complex cancer somatic genetics. However, the analysis of these data is difficult, and failure to consider a number of issues in depth may result in false leads or unnecessary rejection of true positives. First, segmental duplications may falsely generate CN breakpoints in aneuploid samples. Second, even when tumor data were each normalized to matching lymphocyte DNA, we still observed copy number polymorphisms masquerading as somatic alterations due to allelic imbalance. We investigated a number of different solutions and determined that evaluating matching normal DNA, or at least using locally derived normal baseline data, were preferable to relying on current online databases because of poor cross-platform compatibility and the likelihood of excluding genuine small somatic alterations.

  3. 17 CFR 232.104 - Unofficial PDF copies included in an electronic submission.

    Science.gov (United States)

    2010-04-01

    ... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Unofficial PDF copies included... Filing Requirements § 232.104 Unofficial PDF copies included in an electronic submission. (a) An... (§ 249.101 of this chapter) or a Form D (§ 239.500 of this chapter), may include one unofficial PDF copy...

  4. 36 CFR 703.19 - Requests for authenticated copies of Library documents.

    Science.gov (United States)

    2010-07-01

    ... copies of Library documents. 703.19 Section 703.19 Parks, Forests, and Public Property LIBRARY OF... Documents in Certain Legal Proceedings Where the Library Is Not a Party § 703.19 Requests for authenticated copies of Library documents. Requests for authenticated copies of Library documents for purposes...

  5. 78 FR 40156 - Agency Information Collection Activities; Proposed Collection; Comment Request; Copy Testing of...

    Science.gov (United States)

    2013-07-03

    ... Collection; Comment Request; Copy Testing of the Food and Drug Administration's General Market Youth Tobacco... allow 60 days for public comment in response to the notice. This notice solicits comments on Copy... appropriate, and other forms of information technology. Copy Testing of FDA's General Market Youth Tobacco...

  6. Integrated analysis of DNA copy number and gene expression microarray data using gene sets

    NARCIS (Netherlands)

    R.X. de Menezes (Renee); M. Boetzer (Marten); M. Sieswerda (Melle); G.J.B. van Ommen; J.M. Boer (Judith)

    2009-01-01

    textabstractBackground: Genes that play an important role in tumorigenesis are expected to show association between DNA copy number and RNA expression. Optimal power to find such associations can only be achieved if analysing copy number and gene expression jointly. Furthermore, some copy number

  7. Does Visual Attention Span Relate to Eye Movements during Reading and Copying?

    Science.gov (United States)

    Bosse, Marie-Line; Kandel, Sonia; Prado, Chloé; Valdois, Sylviane

    2014-01-01

    This research investigated whether text reading and copying involve visual attention-processing skills. Children in grades 3 and 5 read and copied the same text. We measured eye movements while reading and the number of gaze lifts (GL) during copying. The children were also administered letter report tasks that constitute an estimation of the…

  8. Copy-number and gene dependency analysis reveals partial copy loss of wild-type SF3B1 as a novel cancer vulnerability.

    Science.gov (United States)

    Paolella, Brenton R; Gibson, William J; Urbanski, Laura M; Alberta, John A; Zack, Travis I; Bandopadhayay, Pratiti; Nichols, Caitlin A; Agarwalla, Pankaj K; Brown, Meredith S; Lamothe, Rebecca; Yu, Yong; Choi, Peter S; Obeng, Esther A; Heckl, Dirk; Wei, Guo; Wang, Belinda; Tsherniak, Aviad; Vazquez, Francisca; Weir, Barbara A; Root, David E; Cowley, Glenn S; Buhrlage, Sara J; Stiles, Charles D; Ebert, Benjamin L; Hahn, William C; Reed, Robin; Beroukhim, Rameen

    2017-02-08

    Genomic instability is a hallmark of human cancer, and results in widespread somatic copy number alterations. We used a genome-scale shRNA viability screen in human cancer cell lines to systematically identify genes that are essential in the context of particular copy-number alterations (copy-number associated gene dependencies). The most enriched class of copy-number associated gene dependencies was CYCLOPS (Copy-number alterations Yielding Cancer Liabilities Owing to Partial losS) genes, and spliceosome components were the most prevalent. One of these, the pre-mRNA splicing factor SF3B1, is also frequently mutated in cancer. We validated SF3B1 as a CYCLOPS gene and found that human cancer cells harboring partial SF3B1 copy-loss lack a reservoir of SF3b complex that protects cells with normal SF3B1 copy number from cell death upon partial SF3B1 suppression. These data provide a catalog of copy-number associated gene dependencies and identify partial copy-loss of wild-type SF3B1 as a novel, non-driver cancer gene dependency.

  9. Effects of Organogel Hardness and Formulation on Acceptance of Frankfurters.

    Science.gov (United States)

    Barbut, S; Wood, J; Marangoni, A G

    2016-09-01

    Different organogel formulations used as beef fat (BF) replacement (0%, 20%, 40%, 60%, and 80%) were utilized to optimize the mechanical properties of frankfurters. Organogels, made of canola oil (CO), included different concentrations of ethyl cellulose (EC) and sorbitan monostearate (SMS). They consisted of: 8% EC + 1.5% SMS referred to as organogel-I (OG-I), 8% EC + 3.0% SMS (OG-II), and 10% EC + 1.5% SMS (OG-III), which were found promising in a previous study when used at 100% replacement. Replacement of BF with organogels at all levels could bring down the very high hardness values (texture profile analysis and sensory) of frankfurters prepared using CO by itself, relative to the BF control. OG-I and OG-II quantity had no significant effect on hardness and springiness, being similar in many cases to the BF and lower than the CO control. Shear force values of all organogel treatments were not significantly different from one another, and were between the BF and CO controls. Smokehouse yield showed a pattern of decreasing losses with increasing organogel replacement level. Sensory analysis revealed that using CO by itself significantly increased hardness, but structuring the oil (via organogelation), brought it down to the BF control value in all OG-I and OG-II formulations. Juiciness was significantly reduced by using liquid oil but increased with raising the amount of organogels. Oiliness sensation increased with higher organogel substitution and was actually higher than the beef control. The study demonstrates the potential use of vegetable oil structuring in replacing the more saturated BF in emulsion-type meat products.

  10. Research in the Hard Sciences, and in Very Hard "Softer" Domains

    Science.gov (United States)

    Phillips, D. C.

    2014-01-01

    The author of this commentary argues that physical scientists are attempting to advance knowledge in the so-called hard sciences, whereas education researchers are laboring to increase knowledge and understanding in an "extremely hard" but softer domain. Drawing on the work of Popper and Dewey, this commentary highlights the relative…

  11. Hard Water and Soft Soap: Dependence of Soap Performance on Water Hardness

    Science.gov (United States)

    Osorio, Viktoria K. L.; de Oliveira, Wanda; El Seoud, Omar A.; Cotton, Wyatt; Easdon, Jerry

    2005-01-01

    The demonstration of the performance of soap in different aqueous solutions, which is due to water hardness and soap formulation, is described. The demonstrations use safe, inexpensive reagents and simple glassware and equipment, introduce important everyday topics, stimulates the students to consider the wider consequences of water hardness and…

  12. Analytical Modeling of Hard-Coating Cantilever Composite Plate considering the Material Nonlinearity of Hard Coating

    Directory of Open Access Journals (Sweden)

    Wei Sun

    2015-01-01

    Full Text Available Due to the material nonlinearity of hard coating, the coated structure produces the nonlinear dynamical behaviors of variable stiffness and damping, which make the modeling of hard-coating composite structure become a challenging task. In this study, the polynomial was adopted to characterize this material nonlinearity and an analytical modeling method was developed for the hard-coating composite plate. Firstly, to relate the hard-coating material parameters obtained by test and the analytical model, the expression of equivalent strain of composite plate was derived. Then, the analytical model of hard-coating composite plate was created by energy method considering the material nonlinearity of hard coating. Next, using the Newton-Raphson method to solve the vibration response and resonant frequencies of composite plate and a specific calculation procedure was also proposed. Finally, a cantilever plate coated with MgO + Al2O3 hard coating was chosen as study case; the vibration response and resonant frequencies of composite plate were calculated using the proposed method. The calculation results were compared with the experiment and general linear calculation, and the correctness of the created model was verified. The study shows the proposed method can still maintain an acceptable precision when the material nonlinearity of hard coating is stronger.

  13. Hard Water and Soft Soap: Dependence of Soap Performance on Water Hardness

    Science.gov (United States)

    Osorio, Viktoria K. L.; de Oliveira, Wanda; El Seoud, Omar A.; Cotton, Wyatt; Easdon, Jerry

    2005-01-01

    The demonstration of the performance of soap in different aqueous solutions, which is due to water hardness and soap formulation, is described. The demonstrations use safe, inexpensive reagents and simple glassware and equipment, introduce important everyday topics, stimulates the students to consider the wider consequences of water hardness and…

  14. Surface Hardness of Resin Cement Polymerized under Different Ceramic Materials

    Directory of Open Access Journals (Sweden)

    Pimmada Kesrak

    2012-01-01

    Full Text Available Objectives. To evaluate the surface hardness of two light-cured resin cements polymerized under different ceramic discs. Methods. 40 experimental groups of 2 light-cured resin cement specimens (Variolink Veneer and NX3 were prepared and polymerized under 5 different ceramic discs (IPS e.max Press HT, LT, MO, HO, and Cercon of 4 thicknesses (0.5, 1.0, 1.5, and 2.0 mm, Those directly activated of both resin cements were used as control. After light activation and 37∘C storage in an incubator, Knoop hardness measurements were obtained at the bottom. The data were analyzed with three-way ANOVA, t-test, and one-way ANOVA. Results. The KHN of NX3 was of significantly higher than that of Variolink Veneer (<0.05. The KHN of resin cement polymerized under different ceramic types and thicknesses was significant difference (<0.05. Conclusion. Resin cements polymerized under different ceramic materials and thicknesses showed statistically significant differences in KHN.

  15. Hard X-ray Microscopic Imaging Of Human Breast Tissues

    Science.gov (United States)

    Park, Sung H.; Kim, Hong T.; Kim, Jong K.; Jheon, Sang H.; Youn, Hwa S.

    2007-01-01

    X-ray microscopy with synchrotron radiation will be a useful tool for innovation of x-ray imaging in clinical and laboratory settings. It helps us observe detailed internal structure of material samples non-invasively in air. And, it also has the potential to solve some tough problems of conventional breast imaging if it could evaluate various conditions of breast tissue effectively. A new hard x-ray microscope with a spatial resolution better than 100 nm was installed at Pohang Light Source, a third generation synchrotron radiation facility in Pohang, Korea. The x-ray energy was set at 6.95 keV, and the x-ray beam was monochromatized by W/B4C monochromator. Condenser and objective zone plates were used as x-ray lenses. Zernike phase plate next to condenser zone plate was introduced for improved contrast imaging. The image of a sample was magnified 30 times by objective zone plate and 20 times by microscope objective, respectively. After additional 10 times digital magnification, the total magnifying power was up to 6000 times in the end. Phase contrast synchrotron images of 10-μm-thick female breast tissue of the normal, fibroadenoma, fibrocystic change and carcinoma cases were obtained. By phase contrast imaging, hard x-rays enable us to observe many structures of breast tissue without sample preparations such as staining or fixation.

  16. Stability of Hardly Reshaping Berm Breakwaters

    DEFF Research Database (Denmark)

    Andersen, Thomas Lykke; Van der Meer, Jentsje W.; Burcharth, Hans F.

    2012-01-01

    The present paper deals with stability of berm breakwaters designed to be hardly or sometimes partly reshaping. Burcharth (2008, 2011) showed by comparison to the performance of a prototype berm breakwater that the Van der Meer formulae for stability of conventional rock armour including low crests...... could predict the deformations of the front slope in terms of the eroded area. The present paper verifies the method by comparison to model test results. It is found that the Van der Meer formula for plunging waves predicts very well the eroded area of the reshaped profile, even if it is applied...... of the depth of intersection the last method leads to scatter quite similar to the first method when considering hardly and partly reshaping berm breakwaters. The influence of the slope angle is though expected to be more correctly included for hardly reshaping breakwaters using the method for straight non...

  17. Shock Waves in Dense Hard Disk Fluids

    CERN Document Server

    Sirmas, Nick; Barahona, Javier; Radulescu, Matei I

    2011-01-01

    Media composed of colliding hard disks (2D) or hard spheres (3D) serve as good approximations for the collective hydrodynamic description of gases, liquids and granular media. In the present study, the compressible hydrodynamics and shock dynamics are studied for a two-dimensional hard-disk medium at both the continuum and discrete particle level descriptions. For the continuum description, closed form analytical expressions for the inviscid hydrodynamic description, shock Hugoniot, isentropic exponent and shock jump conditions were obtained using the Helfand equation of state. The closed-form analytical solutions permitted us to gain physical insight on the role of the material's density on its compressibility, i.e. how the medium compresses under mechanical loadings and sustains wave motion. Furthermore, the predictions were found in excellent agreement with calculations using the Event Driven Molecular Dynamic method involving 30,000 particles over the entire range of compressibility spanning the dilute id...

  18. Potential health impacts of hard water.

    Science.gov (United States)

    Sengupta, Pallav

    2013-08-01

    In the past five decades or so evidence has been accumulating about an environmental factor, which appears to be influencing mortality, in particular, cardiovascular mortality, and this is the hardness of the drinking water. In addition, several epidemiological investigations have demonstrated the relation between risk for cardiovascular disease, growth retardation, reproductive failure, and other health problems and hardness of drinking water or its content of magnesium and calcium. In addition, the acidity of the water influences the reabsorption of calcium and magnesium in the renal tubule. Not only, calcium and magnesium, but other constituents also affect different health aspects. Thus, the present review attempts to explore the health effects of hard water and its constituents.

  19. Mucocele of the hard palate in children.

    Science.gov (United States)

    Abdel-Aziz, Mosaad; Khalifa, Badawy; Nassar, Ahmed; Kamel, Ahmed; Naguib, Nader; El-Tahan, Abdel-Rahman

    2016-06-01

    Mucus retention cyst of the hard palate may result from obstruction of the ducts of the minor salivary glands, and it was defined as a mucocele. Although, the disease is not common in the hard palate, it was previously reported by many authors in the soft palate. The aim of our study was to present pediatric patients who were diagnosed to have mucocele of the hard palate, and to evaluate the outcome of the surgical excision of this lesion. This is a case series study included 8 pediatric patients who presented with cystic lesions on the hard palate which were removed surgically, and were diagnosed as mucoceles. Preoperative data, surgical procedures, and postoperative outcome were presented. Follow up of patients was performed for at least one year. The swelling was detected as a single isolated lesion, on the side of the hard palate, covered with healthy mucosa, not tender, oval or round in shape, and measuring 0.4 to 1.7cm in its greatest dimension. Computed tomography showed a well defined cavity which was not invading the bone, and not disrupting the muscles of the palate. Histopathological examination confirmed that the lesion was a cavity that is lined with an epithelial layer with pseudoepitheliomatous hyperplasia. No patients developed intraoperative or postoperative complications, and no recurrence was detected in any patient. Oral mucoceles can develop on the hard palate of the children, the lesions are mucus retention cysts. Complete surgical removal of the lesions with their cystic wall is a good treatment options, it carries no risk of recurrence. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  20. Hard Carbon Fibers Pyrolyzed from Wool as High-Performance Anode for Sodium-Ion Batteries

    Science.gov (United States)

    Zhu, Xiaoming; Li, Qian; Qiu, Shen; Liu, Xiaoling; Xiao, Lifen; Ai, Xinping; Yang, Hanxi; Cao, Yuliang

    2016-10-01

    In this paper, we first demonstrate that the wool from worn-out clothes can serve as a low-cost and easy-to-collect precursor to preparing high-performance hard carbons for Na-ion batteries. Morphological characterizations demonstrate that this wool-derived hard carbon presents well-defined and homogeneously dispersed fiber networks. X-ray diffraction results combined with high-resolution transmission electron microscopy analysis reveal that the interlayer space (d(002)) of the graphitic layers is 0.376 nm, sufficient for Na insertion into the stacked graphene layers. Electrochemical results show that the wool-derived hard carbon can deliver a high capacity of 303 mAh g-1 and excellent cycle stability over 80 cycles. This satisfactory electrochemical performance and easy synthetic procedure make it a promising anode material for practical SIBs.

  1. Elastic Modulus and Hardness of Cr-Nb Nano-Multilayers

    Institute of Scientific and Technical Information of China (English)

    YANG Meng-Jin; LAI Wen-Sheng; PAN Feng

    2007-01-01

    Cr-Nb nano-multilayered films with various modulation wavelengths ∧ are prepared by e-gun evaporation and their mechanical properties are investigated. Cr and Nb both have bcc structures with large differences in lattice constants and Young's modulus, which are supposed to favour modulus enhancement. Nevertheless,nano-indention measurements show no enhancement for the modulus and a slight decrease for the hardness with decreasing ∧ down to 6 nm. This is mainly due to counter-contribution to modulus from adjacent layers subjected to reverse strains, in agreement with recent theoretical study, while the decrease of hardness arises from grain boundary sliding. Interestingly, at ∧ = 3 nm, the hardness of the film has an increase of 44% relative to the value of a rule of mixture, owing to the emergence of a new phase for reconciling the structure difference at the interfaces.

  2. Hardness and incipient plasticity in silicate glasses

    DEFF Research Database (Denmark)

    Kjeldsen, Jonas; Smedskjær, Morten Mattrup; Mauro, John C.;

    2014-01-01

    The scaling of Vickers hardness (Hv) in oxide glasses with varying network modifier/modifier ratio is manifested as either a positive or negative deviation from linearity with a maximum deviation at the ratio of about 1:1. In an earlier study [J. Kjeldsen et al., J. Non-Cryst. Solids 369,61(2013)......The scaling of Vickers hardness (Hv) in oxide glasses with varying network modifier/modifier ratio is manifested as either a positive or negative deviation from linearity with a maximum deviation at the ratio of about 1:1. In an earlier study [J. Kjeldsen et al., J. Non-Cryst. Solids 369...

  3. Environmental change drives accelerated adaptation through stimulated copy number variation

    Science.gov (United States)

    Hull, Ryan M.; Cruz, Cristina; Jack, Carmen V.

    2017-01-01

    Copy number variation (CNV) is rife in eukaryotic genomes and has been implicated in many human disorders, particularly cancer, in which CNV promotes both tumorigenesis and chemotherapy resistance. CNVs are considered random mutations but often arise through replication defects; transcription can interfere with replication fork progression and stability, leading to increased mutation rates at highly transcribed loci. Here we investigate whether inducible promoters can stimulate CNV to yield reproducible, environment-specific genetic changes. We propose a general mechanism for environmentally-stimulated CNV and validate this mechanism for the emergence of copper resistance in budding yeast. By analysing a large cohort of individual cells, we directly demonstrate that CNV of the copper-resistance gene CUP1 is stimulated by environmental copper. CNV stimulation accelerates the formation of novel alleles conferring enhanced copper resistance, such that copper exposure actively drives adaptation to copper-rich environments. Furthermore, quantification of CNV in individual cells reveals remarkable allele selectivity in the rate at which specific environments stimulate CNV. We define the key mechanistic elements underlying this selectivity, demonstrating that CNV is regulated by both promoter activity and acetylation of histone H3 lysine 56 (H3K56ac) and that H3K56ac is required for CUP1 CNV and efficient copper adaptation. Stimulated CNV is not limited to high-copy CUP1 repeat arrays, as we find that H3K56ac also regulates CNV in 3 copy arrays of CUP1 or SFA1 genes. The impact of transcription on DNA damage is well understood, but our research reveals that this apparently problematic association forms a pathway by which mutations can be directed to particular loci in particular environments and furthermore that this mutagenic process can be regulated through histone acetylation. Stimulated CNV therefore represents an unanticipated and remarkably controllable pathway

  4. Copy number variation plays an important role in clinical epilepsy

    Science.gov (United States)

    Olson, Heather; Shen, Yiping; Avallone, Jennifer; Sheidley, Beth R.; Pinsky, Rebecca; Bergin, Ann M.; Berry, Gerard T.; Duffy, Frank H.; Eksioglu, Yaman; Harris, David J.; Hisama, Fuki M.; Ho, Eugenia; Irons, Mira; Jacobsen, Christina M.; James, Philip; Kothare, Sanjeev; Khwaja, Omar; Lipton, Jonathan; Loddenkemper, Tobias; Markowitz, Jennifer; Maski, Kiran; Megerian, J. Thomas; Neilan, Edward; Raffalli, Peter C.; Robbins, Michael; Roberts, Amy; Roe, Eugene; Rollins, Caitlin; Sahin, Mustafa; Sarco, Dean; Schonwald, Alison; Smith, Sharon E.; Soul, Janet; Stoler, Joan M.; Takeoka, Masanori; Tan, Wen-Han; Torres, Alcy R.; Tsai, Peter; Urion, David K.; Weissman, Laura; Wolff, Robert; Wu, Bai-Lin; Miller, David T.; Poduri, Annapurna

    2015-01-01

    Objective To evaluate the role of copy number abnormalities detectable by chromosomal microarray (CMA) testing in patients with epilepsy at a tertiary care center. Methods We identified patients with ICD-9 codes for epilepsy or seizures and clinical CMA testing performed between October 2006 and February 2011 at Boston Children’s Hospital. We reviewed medical records and included patients meeting criteria for epilepsy. We phenotypically characterized patients with epilepsy-associated abnormalities on CMA. Results Of 973 patients who had CMA and ICD-9 codes for epilepsy or seizures, 805 patients satisfied criteria for epilepsy. We observed 437 copy number variants (CNVs) in 323 patients (1–4 per patient), including 185 (42%) deletions and 252 (58%) duplications. Forty (9%) were confirmed de novo, 186 (43%) were inherited, and parental data were unavailable for 211 (48%). Excluding full chromosome trisomies, CNV size ranged from 18 kb to 142 Mb, and 34% were over 500 kb. In at least 40 cases (5%), the epilepsy phenotype was explained by a CNV, including 29 patients with epilepsy-associated syndromes and 11 with likely disease-associated CNVs involving epilepsy genes or “hotspots.” We observed numerous recurrent CNVs including 10 involving loss or gain of Xp22.31, a region described in patients with and without epilepsy. Interpretation Copy number abnormalities play an important role in patients with epilepsy. Given that the diagnostic yield of CMA for epilepsy patients is similar to the yield in autism spectrum disorders and in prenatal diagnosis, for which published guidelines recommend testing with CMA, we recommend the implementation of CMA in the evaluation of unexplained epilepsy. PMID:24811917

  5. Bias of selection on human copy-number variants.

    Directory of Open Access Journals (Sweden)

    2006-02-01

    Full Text Available Although large-scale copy-number variation is an important contributor to conspecific genomic diversity, whether these variants frequently contribute to human phenotype differences remains unknown. If they have few functional consequences, then copy-number variants (CNVs might be expected both to be distributed uniformly throughout the human genome and to encode genes that are characteristic of the genome as a whole. We find that human CNVs are significantly overrepresented close to telomeres and centromeres and in simple tandem repeat sequences. Additionally, human CNVs were observed to be unusually enriched in those protein-coding genes that have experienced significantly elevated synonymous and nonsynonymous nucleotide substitution rates, estimated between single human and mouse orthologues. CNV genes encode disproportionately large numbers of secreted, olfactory, and immunity proteins, although they contain fewer than expected genes associated with Mendelian disease. Despite mouse CNVs also exhibiting a significant elevation in synonymous substitution rates, in most other respects they do not differ significantly from the genomic background. Nevertheless, they encode proteins that are depleted in olfactory function, and they exhibit significantly decreased amino acid sequence divergence. Natural selection appears to have acted discriminately among human CNV genes. The significant overabundance, within human CNVs, of genes associated with olfaction, immunity, protein secretion, and elevated coding sequence divergence, indicates that a subset may have been retained in the human population due to the adaptive benefit of increased gene dosage. By contrast, the functional characteristics of mouse CNVs either suggest that advantageous gene copies have been depleted during recent selective breeding of laboratory mouse strains or suggest that they were preferentially fixed as a consequence of the larger effective population size of wild mice. It

  6. Carbonaceous Chondrite Thin Section Preparation

    Science.gov (United States)

    Harrington, R.; Righter, K.

    2017-01-01

    Carbonaceous chondrite meteorites have long posed a challenge for thin section makers. The variability in sample hardness among the different types, and sometimes within individual sections, creates the need for an adaptable approach at each step of the thin section making process. This poster will share some of the procedural adjustments that have proven to be successful at the NASA JSC Meteorite Thin Section Laboratory. These adjustments are modifications of preparation methods that have been in use for decades and therefore do not require investment in new technology or materials.

  7. Fundamental Costs in the Production and Destruction of Persistent Polymer Copies

    Science.gov (United States)

    Ouldridge, Thomas E.; Rein ten Wolde, Pieter

    2017-04-01

    Producing a polymer copy of a polymer template is central to biology, and effective copies must persist after template separation. We show that this separation has three fundamental thermodynamic effects. First, polymer-template interactions do not contribute to overall reaction thermodynamics and hence cannot drive the process. Second, the equilibrium state of the copied polymer is template independent and so additional work is required to provide specificity. Finally, the mixing of copies from distinct templates makes correlations between template and copy sequences unexploitable, combining with copying inaccuracy to reduce the free energy stored in a polymer ensemble. These basic principles set limits on the underlying costs and resource requirements, and suggest design principles, for autonomous copying and replication in biological and synthetic systems.

  8. Analysis of the development and performance of hard disks

    OpenAIRE

    Novak, Davorin

    2010-01-01

    With the emergence of new technologies in the field of hard drives we can witness a significant increase of surface density and transfer rate of interfaces which, as a result, enables greater performance and reliability of hard disks. The reason for this are increasing needs for higher capacities and data transfer rate to or from the hard disk. This thesis presents the structure of hard drives, features, performance and reliability of hard drives and alternative data storage technologies. Par...

  9. Comparison of different hardness definitions usable for micro- and nanoindentation

    Energy Technology Data Exchange (ETDEWEB)

    Pohlenz, F.; Herrmann, K.; Seemann, R.; Menelao, F. [Physikalisch-Technische Bundesanstalt, Braunschweig (Germany)

    2001-09-01

    In order to describe the hardness of substrates and layers, different definitions are used which consider the plastic or the elastic-plastic behavior of the material. For a chosen spectrum of substrate and layer materials the absolute hardness values according to these definitions are compared with each other. Moreover, relationships between the hardness values are derived. For the investigation of differences in the accuracy of the various hardness definitions the variance coefficients of different hardnesses were determined. (orig.)

  10. Difluoromethane preparation

    NARCIS (Netherlands)

    Wiersma, A.; Sandt, E.J.A.; Van Bekkum, H.; Makkee, M.; Moulijn, J.A.

    1996-01-01

    Abstract of NL 9401574 (A) The invention relates to a method for preparing difluoromethane, wherein dichlorodifluoromethane or monochlorodifluoromethane is brought into contact with hydrogen in the presence of palladium on activated carbon, wherein the loading of the palladium on the activated c

  11. Remember Hard but Think Softly: Metaphorical Effects of Hardness/Softness on Cognitive Functions

    Directory of Open Access Journals (Sweden)

    Jiushu Xie

    2016-09-01

    Full Text Available Previous studies have found that bodily stimulation, such as hardness, biases social judgment and evaluation via metaphorical association; however, it remains unclear whether bodily stimulation also affects cognitive functions, such as memory and creativity. The current study used metaphorical associations between hard and rigid and between soft and flexible in Chinese, to investigate whether the experience of hardness affected cognitive functions requiring either rigidity (memory or flexibility (creativity. In Experiment 1, we found that Chinese-speaking participants performed better at recalling previously memorized words while sitting on a hard-surface stool (the hard condition than a cushioned one (the soft condition. In Experiment 2, participants sitting on a cushioned stool outperformed those sitting on a hard-surface stool on a Chinese riddle task, which required creative/flexible thinking, but not on an analogical reasoning task, which required both rigid and flexible thinking. The results suggest the hardness experience affects cognitive functions that are metaphorically associated with rigidity and flexibility. They support the embodiment proposition that cognitive functions and representations could be grounded via metaphorical association in bodily states.

  12. The influence of hard segment content on mechanical and thermal properties of polycarbonate-based polyurethane materials

    Directory of Open Access Journals (Sweden)

    Budinski-Simendić Jaroslava

    2012-01-01

    Full Text Available Aliphatic segmented polyurethanes were prepared by one-step procedure in catalytic reaction between polycarbonate diol, hexamethylene-diisocyanate and 1,4-butandiol (as chain extender. The hard segment content TS was varied (17, 24, 30 and 42 wt. % by changing the ratio of starting compounds. The soft segment is made from flexible aliphatic polycarbonate diol, while hard segments consist of chain extender and diisocyanate component. In order to study the hydrogen bonding formation and phase separation, Fourier transform infrared spectroscopy (FT-IR was used. Wide angle X-ray scattering (WAXS was performed to determine a degree of crystallinity and to investigate the phase behavior of prepared elastomers. The effect of TS content on mechanical properties (tensile strength, elongation at break and hardness was tested. Thermal behavior of prepared novel polycarbonate-based polyurethanes was investigated using differential scanning callorimetry (DSC. It was determined that the elastomer which contains the highest amount of urethane groups in its structure (TS content of 42 wt. % exhibits the most pronounced phase separation and the highest degree of crystallinity. All prepared polyurethanes exhibit high elongation at break (over 700%. The glass transition temperature Tg of prepared samples was in the temperature region from −39 to −36°C, and it was found to be slightly influenced by the soft segment content. The enthalpy of chain segments relaxation in diffused region between hard and soft domains (detected in the temperature range from 35 to 55 °C was decreased with the increase of hard segment content. The multiple melting of hard segments (connected with the dissruption of physical crosslinks appeared above 100 °C. It was found that the melting enthalpy linearly increases with the increase of urethane group content. Sample with 42 wt. % of TS has the highest value of melting enthalpy (41.5 J/g.

  13. Stability of Hardly Reshaping Berm Breakwaters

    DEFF Research Database (Denmark)

    Andersen, Thomas Lykke; Van der Meer, Jentsje W.; Burcharth, Hans F.;

    2012-01-01

    in the surging wave area. Moreover, a simple method to estimate the erosion area based on recession formulae and the depth of intersection of reshaped and initial profile is presented and is applicable for hardly reshaping to fully reshaping. Even when using the only very simple and inaccurate estimate...

  14. Registration of 'Sunshine' Hard White Winter Wheat

    Science.gov (United States)

    ’Sunshine’ (Reg. No. CV-XXXX, PI 674741) hard white winter wheat (Triticum aestivum L.) was developed by the Colorado Agricultural Experiment Station and released in August 2014 through a marketing agreement with the Colorado Wheat Research Foundation. In addition to researchers at Colorado State Un...

  15. Imaging in Hard X-ray Astronomy

    CERN Document Server

    Li Ti Pei

    2002-01-01

    The energy range of hard X-rays is a key waveband to the study of high energy processes in celestial objects, but still remains poorly explored. In contrast to direct imaging methods used in the low energy X-ray and high energy gamma-ray bands, currently imaging in the hard X-ray band is mainly achieved through various modulation techniques. A new inversion technique, the direct demodulation method, has been developed since early 90s. With this technique, wide field and high resolution images can be derived from scanning data of a simple collimated detector. The feasibility of this technique has been confirmed by experiment, balloon-borne observation and analyzing simulated and real astronomical data. Based the development of methodology and instrumentation, a high energy astrophysics mission -- Hard X-ray Modulation Telescope (HXMT) has been proposed and selected in China for a four-year Phase-A study. The main scientific objectives are a full-sky hard X-ray (20-200 keV) imaging survey and high signal-to-noi...

  16. Doubly diffracted ray from a hard quarterplane

    DEFF Research Database (Denmark)

    Albertsen, Niels Christian

    2000-01-01

    The scattering of the electromagnetic field from a half wave dipole source around a quarterplane can be calculated from the solutions to two scalar problems, one with a soft quarterplane and one with a hard quarterplane. In both cases, a doubly diffracted ray may exist, but only in the case of th...

  17. Hard Times: Philosophy and the Fundamentalist Imagination

    Science.gov (United States)

    Allsup, Randall Everett

    2005-01-01

    A close reading of Gradgrind's opening monologue of Hard Times by Charles Dickens will provide the starting off point for an examination of the role and place of philosophy in the music curriculum. The Gradgrind philosophy finds easy parallel to current thinking in American education. In the fundamentalist imagination, sources of ambiguity must be…

  18. Parallel Narrative Structure in Paul Harding's "Tinkers"

    Science.gov (United States)

    Çirakli, Mustafa Zeki

    2014-01-01

    The present paper explores the implications of parallel narrative structure in Paul Harding's "Tinkers" (2009). Besides primarily recounting the two sets of parallel narratives, "Tinkers" also comprises of seemingly unrelated fragments such as excerpts from clock repair manuals and diaries. The main stories, however, told…

  19. Radiation-Hardness Data For Semiconductor Devices

    Science.gov (United States)

    Price, W. E.; Nichols, D. K.; Brown, S. F.; Gauthier, M. K.; Martin, K. E.

    1984-01-01

    Document presents data on and analysis of radiation hardness of various semiconductor devices. Data specifies total-dose radiation tolerance of devices. Volume 1 of report covers diodes, bipolar transistors, field effect transistors, silicon controlled rectifiers and optical devices. Volume 2 covers integrated circuits. Volume 3 provides detailed analysis of data in volumes 1 and 2.

  20. Ototraumatic effects of hard rock music.

    Science.gov (United States)

    Reddell, R C; Lebo, C P

    1972-01-01

    Temporary and permanent shifts in auditory thresholds were found in 43 hard rock musicians and temporary shifts were also observed in some listeners. The threshold shifts involved all of the conventional puretone test frequencies. Custom-fitted polyvinyl chloride ear protectors were found to be effective in prevention of these noise-induced hearing losses.

  1. Hard x-ray telescope mission

    DEFF Research Database (Denmark)

    Gorenstein, P.; Worrall, D.; Joensen, K.D.

    1996-01-01

    The Hard X-Ray Telescope was selected for study as a possible new intermediate size mission for the early 21st century. Its principal attributes are: (1) multiwavelength observing with a system of focussing telescopes that collectively observe from the UV to over 1 MeV, (2) much higher sensitivity...

  2. Hardness of basaltic glass-ceramics

    DEFF Research Database (Denmark)

    Jensen, Martin; Smedskjær, Morten Mattrup; Estrup, Maja;

    2009-01-01

    The dependence of the hardness of basaltic glass-ceramics on their degree of crystallisation has been explored by means of differential scanning calorimetry, optical microscopy, x-ray diffraction, and Vickers indentation. Different degrees of crystallisation in the basaltic glasses were achieved...

  3. Hard scattering in {gamma}p interactions

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, T.; Andreev, V.; Andrieu, B.; Arpagaus, M.; Babayev, A.; Baerwolff, H.; Ban, J.; Baranov, P.; Barrelet, E.; Bartel, W.; Bassler, U.; Beck, G.A.; Beck, H.P.; Behrend, H.J.; Belousov, A.; Berger, C.; Bergstein, H.; Bernardi, G.; Bernet, R.; Bertrand-Coremans, G.; Besancon, M.; Biddulph, P.; Binder, E.; Bizot, J.C.; Blobel, V.; Borras, K.; Bosetti, P.C.; Boudry, V.; Bourdarios, C.; Brasse, F.; Braun, U.; Braunschweig, W.; Brisson, V.; Bruncko, D.; Buerger, J.; Buesser, F.W.; Buniatian, A.; Burke, S.; Buschhorn, G.; Campbell, A.J.; Carli, T.; Charles, F.; Clarke, D.; Clegg, A.B.; Colombo, M.; Coughlan, J.A.; Courau, A.; Coutures, C.; Cozzika, G.; Criegee, L.; Cvach, J.; Dainton, J.B.; Danilov, M.; Dann, A.W.E.; Dau, W.D.; David, M.; Deffur, E.; Delcourt, B.; DelBuono, L.; Devel, M.; DeRoeck, A.; Dingus, P.; Dollfus, C.; Dowell, J.D.; Dreis, H.B.; Drescher, A.; Duboc, J.; Duellmann, D.; Duenger, O.; Duhm, H.; Eberle, M.; Ebert, J.; Ebert, T.R.; Eckerlin, G.; Efremenko, V.; Egli, S.; Eichenberger, S.; Eichler, R.; Eisele, F.; Eisenhandler, E.; Ellis, N.N.; Ellison, R.J.; Elsen, E.; Erdmann, M.; Evrard, E.; Favart, L.; Fedotov, A.; Feeken, D.; Felst, R.; Feltesse, J.; Feng, Y.; Fensome, I.F.; Ferencei, J.; Ferrarotto, F.; Flauger, W.; Fleischer, M.; Fluegge, G.; Fomenko, A.; Fomynich, B.; Forbush, M.; Formanek, J.; Foster, J.M.; Franke, G.; Fretwurst, E.; Fuhrmann, P.; Gabathuler, E.; Gamerdinger, K.; Garvey, J.; Gayler, J.; Gellrich, A.; Gennis, M.; Gensch, U.; Genzel, H.; Gerhards, R.; Gillespie, D.; Godfrey, L.; Goerlach, U.; Goerlich, L.; Goldberg, M.; Goodall, A.M.; Gorelov, I.; Goritchev, P.; Grab, C.; Graessler, H.; Graessler, R.; Greenshaw, T.; Greif, H.; Grindhammer, G.; Gruber, C.; Haack, J.; Haguenauer, M.; Haidt, D.; Hajduk, L.; Hamon, O.; Handschuh, D.; Hanlon, E.M.; Hapke, M.; Harjes, J.; Hartz, P.; Haydar, R.; Haynes, W.J.; Heatherington, J.; Hedberg, V.; Hedgecock, R.; Heinzelmann, G.; Henderson, R.C.W.; Henschel, H.; Herma, R.; H1 Collaboration

    1992-10-01

    We report on the investigation of the final state in interactions of quasi-real photons with protons. The data were taken with the H1 detector at the HERA ep collider. Evidence for hard interactions is seen in both single particle spectra and jet formation. The data can best be described by inclusion of resolved photon processes as predicted by QCD. (orig.).

  4. Hardness of basaltic glass-ceramics

    DEFF Research Database (Denmark)

    Jensen, Martin; Smedskjær, Morten Mattrup; Estrup, Maja

    2009-01-01

    The dependence of the hardness of basaltic glass-ceramics on their degree of crystallisation has been explored by means of differential scanning calorimetry, optical microscopy, x-ray diffraction, and Vickers indentation. Different degrees of crystallisation in the basaltic glasses were achieved...

  5. "Work smart, wear your hard hat"

    CERN Multimedia

    2003-01-01

    Falling objects and collisions are frequent occurrences in work sites and hazardous areas. Hard hats can help prevent many types of accident and can even save lives. Just imagine an 800 g spanner falling from a 13 m high scaffold onto the head of someone standing below - a nightmare scenario! The impact to the head is equivalent to that of a 5 kg weight falling from 2 metres. That is just what happened to Gerd Fetchenhauer when he was working on the UA1 experiment. Fortunately, he was wearing a hard hat at the time. "That hat saved my life," he explains. "It punched a hole right through the hat and I was a bit dazed for a couple of hours but otherwise I was OK." Since that day, Gerd Fetchenhauer, now working on CMS, is never seen on a work site without his hard hat on. Work sites have proliferated at CERN with the construction of the LHC and its detectors, and the wearing of hard hats is compulsory (not to mention life-saving). In the underground caverns and experiment halls, where gantry cranes and other h...

  6. Canada,China,Closer in Hard Times

    Institute of Scientific and Technical Information of China (English)

    Guo Liqin

    2008-01-01

    @@ Facing the current global financial storm,more posSible economic and trade cooperation and promotion worldwide is being sought by nations to walk out the hard time.The 2nd Canada China Business Forum held in Beijing,on November 3,is an example to a closer tie of both countries.

  7. The glass transition of hard spherical colloids

    Energy Technology Data Exchange (ETDEWEB)

    Pusey, P.N. (Royal Signals and Radar Establishment, Malvern (UK)); Van Megen, W. (Royal Melbourne Inst. of Tech. (Australia). Dept. of Applied Physics)

    1990-03-01

    When suspended in a liquid, hard spherical colloidal particles can show fluid, crystalline and glassy phases. A light scattering study of the dynamics of the metastable fluid and glassy phases is reported. Comparison is made with the predictions of mode-coupling theories applied to the glass transition of simple atomic systems. (orig.).

  8. Confirmed rare copy number variants implicate novel genes in schizophrenia.

    Science.gov (United States)

    Tam, Gloria W C; van de Lagemaat, Louie N; Redon, Richard; Strathdee, Karen E; Croning, Mike D R; Malloy, Mary P; Muir, Walter J; Pickard, Ben S; Deary, Ian J; Blackwood, Douglas H R; Carter, Nigel P; Grant, Seth G N

    2010-04-01

    Understanding how cognitive processes including learning, memory, decision making and ideation are encoded by the genome is a key question in biology. Identification of sets of genes underlying human mental disorders is a path towards this objective. Schizophrenia is a common disease with cognitive symptoms, high heritability and complex genetics. We have identified genes involved with schizophrenia by measuring differences in DNA copy number across the entire genome in 91 schizophrenia cases and 92 controls in the Scottish population. Our data reproduce rare and common variants observed in public domain data from >3000 schizophrenia cases, confirming known disease loci as well as identifying novel loci. We found copy number variants in PDE10A (phosphodiesterase 10A), CYFIP1 [cytoplasmic FMR1 (Fragile X mental retardation 1)-interacting protein 1], K(+) channel genes KCNE1 and KCNE2, the Down's syndrome critical region 1 gene RCAN1 (regulator of calcineurin 1), cell-recognition protein CHL1 (cell adhesion molecule with homology with L1CAM), the transcription factor SP4 (specificity protein 4) and histone deacetylase HDAC9, among others (see http://www.genes2cognition.org/SCZ-CNV). Integrating the function of these many genes into a coherent model of schizophrenia and cognition is a major unanswered challenge.

  9. Copy number variation of KIR genes influences HIV-1 control

    DEFF Research Database (Denmark)

    Pelak, Kimberly; Need, Anna C; Fellay, Jacques;

    2011-01-01

    A genome-wide screen for large structural variants showed that a copy number variant (CNV) in the region encoding killer cell immunoglobulin-like receptors (KIR) associates with HIV-1 control as measured by plasma viral load at set point in individuals of European ancestry. This CNV encompasses...... the KIR3DL1-KIR3DS1 locus, encoding receptors that interact with specific HLA-Bw4 molecules to regulate the activation of lymphocyte subsets including natural killer (NK) cells. We quantified the number of copies of KIR3DS1 and KIR3DL1 in a large HIV-1 positive cohort, and showed that an increase in KIR3......DS1 count associates with a lower viral set point if its putative ligand is present (p = 0.00028), as does an increase in KIR3DL1 count in the presence of KIR3DS1 and appropriate ligands for both receptors (p = 0.0015). We further provide functional data that demonstrate that NK cells from...

  10. Copy Number Alterations and Methylation in Ewing's Sarcoma

    Directory of Open Access Journals (Sweden)

    Mona S. Jahromi

    2011-01-01

    Full Text Available Ewing's sarcoma is the second most common bone malignancy affecting children and young adults. The prognosis is especially poor in metastatic or relapsed disease. The cell of origin remains elusive, but the EWS-FLI1 fusion oncoprotein is present in the majority of cases. The understanding of the molecular basis of Ewing's sarcoma continues to progress slowly. EWS-FLI1 affects gene expression, but other factors must also be at work such as mutations, gene copy number alterations, and promoter methylation. This paper explores in depth two molecular aspects of Ewing's sarcoma: copy number alterations (CNAs and methylation. While CNAs consistently have been reported in Ewing's sarcoma, their clinical significance has been variable, most likely due to small sample size and tumor heterogeneity. Methylation is thought to be important in oncogenesis and balanced karyotype cancers such as Ewing's, yet it has received only minimal attention in prior studies. Future CNA and methylation studies will help to understand the molecular basis of this disease.

  11. Flip-invariant SIFT for copy and object detection.

    Science.gov (United States)

    Zhao, Wan-Lei; Ngo, Chong-Wah

    2013-03-01

    Scale-invariant feature transform (SIFT) feature has been widely accepted as an effective local keypoint descriptor for its invariance to rotation, scale, and lighting changes in images. However, it is also well known that SIFT, which is derived from directionally sensitive gradient fields, is not flip invariant. In real-world applications, flip or flip-like transformations are commonly observed in images due to artificial flipping, opposite capturing viewpoint, or symmetric patterns of objects. This paper proposes a new descriptor, named flip-invariant SIFT (or F-SIFT), that preserves the original properties of SIFT while being tolerant to flips. F-SIFT starts by estimating the dominant curl of a local patch and then geometrically normalizes the patch by flipping before the computation of SIFT. We demonstrate the power of F-SIFT on three tasks: large-scale video copy detection, object recognition, and detection. In copy detection, a framework, which smartly indices the flip properties of F-SIFT for rapid filtering and weak geometric checking, is proposed. F-SIFT not only significantly improves the detection accuracy of SIFT, but also leads to a more than 50% savings in computational cost. In object recognition, we demonstrate the superiority of F-SIFT in dealing with flip transformation by comparing it to seven other descriptors. In object detection, we further show the ability of F-SIFT in describing symmetric objects. Consistent improvement across different kinds of keypoint detectors is observed for F-SIFT over the original SIFT.

  12. Plasmid copy number noise in monoclonal populations of bacteria

    Science.gov (United States)

    Wong Ng, Jérôme; Chatenay, Didier; Robert, Jérôme; Poirier, Michael Guy

    2010-01-01

    Plasmids are extra chromosomal DNA that can confer to their hosts’ supplementary characteristics such as antibiotic resistance. Plasmids code for their copy number through their own replication frequency. Even though the biochemical networks underlying the plasmid copy number (PCN) regulation processes have been studied and modeled, no measurement of the heterogeneity in PCN within a whole population has been done. We have developed a fluorescent-based measurement system, which enables determination of the mean and noise in PCN within a monoclonal population of bacteria. Two different fluorescent protein reporters were inserted: one on the chromosome and the other on the plasmid. The fluorescence of these bacteria was measured with a microfluidic flow cytometry device. We show that our measurements are consistent with known plasmid characteristics. We find that the partitioning system lowers the PCN mean and standard deviation. Finally, bacterial populations were allowed to grow without selective pressure. In this case, we were able to determine the plasmid loss rate and growth inhibition effect.

  13. One Method for Inhibiting the Copying of Online Homework

    Science.gov (United States)

    Busch, Hauke

    2017-10-01

    Over the last several years online homework solutions have become ever more accessible to students. This is due in part to programs like Yahoo Answers, Chegg, publisher solution manuals, and other web resources that are readily available online. The student can easily search any physics homework problem posted on the web in a matter of seconds and have the solution. The results of this are an apparent increase in students copying the answers without solving the problem, which may lead to an increase in homework scores but a reduction in exam scores and an overall lower grade in the class. A secondary effect that may be observed is that tutoring centers, recitations, and supplemental instructor sessions have reduced student attendance. Some might say that the readily available solutions for homework systems such as MasteringPhysics (MP), WebAssign, etc. have greatly diminished them as a teaching tool, and for grading and assessing students' performance in a course. It is the purpose of this paper to offer a possible solution for preventing students from potentially copying online homework solutions.

  14. BCJ duality and double copy in the closed string sector

    Energy Technology Data Exchange (ETDEWEB)

    Ochirov, Alexander; Tourkine, Piotr [Institut de Physique Théorique, CEA-Saclay,F-91191 Gif-sur-Yvette cedex (France)

    2014-05-28

    This paper is focused on the loop-level understanding of the Bern-Carrasco-Johansson double copy procedure that relates the integrands of gauge theory and gravity scattering amplitudes. At four points, the first non-trivial example of that construction is one-loop amplitudes in N = 2 super-Yang-Mills theory and the symmetric realization of N = 4 matter-coupled supergravity. Our approach is to use both field and string theory in parallel to analyze these amplitudes. The closed string provides a natural framework to analyze the BCJ construction, in which the left- and right-moving sectors separately create the color and kinematics at the integrand level. At tree level, in a five-point example, we show that the Mafra-Schlotterer-Stieberger procedure gives a new direct proof of the color-kinematics double copy. We outline the extension of that argument to n points. At loop level, the field-theoretic BCJ construction of N = 2 SYM amplitudes introduces new terms, unexpected from the string theory perspective. We discuss to what extent we can relate them to the terms coming from the interactions between left- and right-movers in the string-theoretic gravity construction.

  15. Developmental environment, cultural transmission, and mate choice copying

    Science.gov (United States)

    Dugatkin, Lee Alan

    2007-08-01

    Using female mate choice copying as a rudimentary form of cultural transmission, this study provides evidence that social environment during development has a significant effect on the tendency to use culturally acquired information. Groups of newborn guppies (Poecilia reticulata) were raised for 35 days in 1 of 5 “developmental environments”. Groups of 15 newborns were raised in pools with no adults (treatment 1), both adult male and female guppies (treatments 2 and 3), only adult females (treatment 4) or only adult males (treatment 5). Mature females raised in treatments 1 and 2, but not treatments 3, 4, and 5, copied the mate choice of others. Treatments 1 and 2 correspond to social structures that guppies experience during their development in the wild. Newborn guppies swim together in shoals (analogous to treatment 1). As they mature, juveniles join schools of adult males and females (analogous to treatments 2). At no time during the normal developmental process are juveniles found with males, but only unreceptive females (as was the case for long periods in treatment 3) or in the presence of adults of only one sex (analogous to treatments 4 and 5). As such, normal developmental environments prime guppies for cultural transmission, while unnatural environments fail to do so.

  16. Why copy others? Insights from the social learning strategies tournament.

    Science.gov (United States)

    Rendell, L; Boyd, R; Cownden, D; Enquist, M; Eriksson, K; Feldman, M W; Fogarty, L; Ghirlanda, S; Lillicrap, T; Laland, K N

    2010-04-09

    Social learning (learning through observation or interaction with other individuals) is widespread in nature and is central to the remarkable success of humanity, yet it remains unclear why copying is profitable and how to copy most effectively. To address these questions, we organized a computer tournament in which entrants submitted strategies specifying how to use social learning and its asocial alternative (for example, trial-and-error learning) to acquire adaptive behavior in a complex environment. Most current theory predicts the emergence of mixed strategies that rely on some combination of the two types of learning. In the tournament, however, strategies that relied heavily on social learning were found to be remarkably successful, even when asocial information was no more costly than social information. Social learning proved advantageous because individuals frequently demonstrated the highest-payoff behavior in their repertoire, inadvertently filtering information for copiers. The winning strategy (discountmachine) relied nearly exclusively on social learning and weighted information according to the time since acquisition.

  17. Developmental environment, cultural transmission, and mate choice copying.

    Science.gov (United States)

    Dugatkin, Lee Alan

    2007-08-01

    Using female mate choice copying as a rudimentary form of cultural transmission, this study provides evidence that social environment during development has a significant effect on the tendency to use culturally acquired information. Groups of newborn guppies (Poecilia reticulata) were raised for 35 days in 1 of 5 "developmental environments". Groups of 15 newborns were raised in pools with no adults (treatment 1), both adult male and female guppies (treatments 2 and 3), only adult females (treatment 4) or only adult males (treatment 5). Mature females raised in treatments 1 and 2, but not treatments 3, 4, and 5, copied the mate choice of others. Treatments 1 and 2 correspond to social structures that guppies experience during their development in the wild. Newborn guppies swim together in shoals (analogous to treatment 1). As they mature, juveniles join schools of adult males and females (analogous to treatments 2). At no time during the normal developmental process are juveniles found with males, but only unreceptive females (as was the case for long periods in treatment 3) or in the presence of adults of only one sex (analogous to treatments 4 and 5). As such, normal developmental environments prime guppies for cultural transmission, while unnatural environments fail to do so.

  18. The phase behavior of linear and partially flexible hard-sphere chain fluids and the solubility of hard spheres in hard-sphere chain fluids

    NARCIS (Netherlands)

    Oyarzun, B.A.; Van Westen, T.; Vlugt, T.J.H.

    2013-01-01

    he liquid crystal phase behavior of linear and partially flexible hard-sphere chain fluids and the solubility of hard spheres in hard-sphere chain fluids are studied by constant pressure Monte Carlo simulations. An extensive study on the phase behavior of linear fluids with a length of 7, 8, 9, 10,

  19. Effects of home bleaching on surface hardness and surface roughness of an experimental nanocomposite

    Science.gov (United States)

    Zuryati, Ab-Ghani; Qian, Ooi Qian; Dasmawati, Mohamad

    2013-01-01

    Objective: Home bleaching agents may not be safe for composite resins. The purpose of this study was to evaluate the effects of 10 and 20% Opalescence® PF home bleaching agents on the surface roughness and hardness of universal nanocomposite (Filtek Z350), anterior nanocomposite (KeLFiL), and nanohybrid composite (TPH 3). Materials and Methods: Fifty-four composite resin samples with 18 samples for each type of composite resin were prepared using acrylic molds (4 × 2 mm). Each type of composite resin was further divided into three groups [n = 6 controls were placed in distilled water for 14 days and the other two groups of n = 6 were bleached with 10 and 20% carbamide peroxide (CP), respectively for 14 days]. Surface hardness of the composite resin was tested with a Vickers hardness tester, whereas surface roughness was tested with atomic force microscopy (AFM). Results: There were significant changes in the surface hardness of KeLFiL and TPH 3. However, all the tested materials showed no significant changes in the surface roughness. Conclusion: After 14 days of home bleaching treatment, there was no adverse effect on the surface roughness of all three composite resins, although the surface hardness for KeLFiL and TPH 3 were significantly reduced. PMID:23956541

  20. Effects of home bleaching on surface hardness and surface roughness of an experimental nanocomposite

    Directory of Open Access Journals (Sweden)

    Ab-Ghani Zuryati

    2013-01-01

    Full Text Available Objective: Home bleaching agents may not be safe for composite resins. The purpose of this study was to evaluate the effects of 10 and 20% Opalescence ® PF home bleaching agents on the surface roughness and hardness of universal nanocomposite (Filtek Z350, anterior nanocomposite (KeLFiL, and nanohybrid composite (TPH 3. Materials and Methods: Fifty-four composite resin samples with 18 samples for each type of composite resin were prepared using acrylic molds (4 × 2 mm. Each type of composite resin was further divided into three groups [n = 6 controls were placed in distilled water for 14 days and the other two groups of n = 6 were bleached with 10 and 20% carbamide peroxide (CP, respectively for 14 days]. Surface hardness of the composite resin was tested with a Vickers hardness tester, whereas surface roughness was tested with atomic force microscopy (AFM. Results: There were significant changes in the surface hardness of KeLFiL and TPH 3. However, all the tested materials showed no significant changes in the surface roughness. Conclusion: After 14 days of home bleaching treatment, there was no adverse effect on the surface roughness of all three composite resins, although the surface hardness for KeLFiL and TPH 3 were significantly reduced.

  1. Chemical Characterization of Beer Aging Products Derived from Hard Resin Components in Hops (Humulus lupulus L.).

    Science.gov (United States)

    Taniguchi, Yoshimasa; Yamada, Makiko; Taniguchi, Harumi; Matsukura, Yasuko; Shindo, Kazutoshi

    2015-11-25

    The bitter taste of beer originates from resins in hops (Humulus lupulus L.), which are classified into two subtypes (soft and hard). Whereas the nature and reactivity of soft-resin-derived compounds, such as α-, β-, and iso-α-acids, are well studied, there is only a little information on the compounds in hard resin. For this work, hard resin was prepared from stored hops and investigated for its compositional changes in an experimental model of beer aging. The hard resin contained a series of α-acid oxides. Among them, 4'-hydroxyallohumulinones were unstable under beer storage conditions, and their transformation induced primary compositional changes of the hard resin during beer aging. The chemical structures of the products, including novel polycyclic compounds scorpiohumulinols A and B and dicyclohumulinols A and B, were determined by HRMS and NMR analyses. These compounds were proposed to be produced via proton-catalyzed cyclization reactions of 4'-hydroxyallohumulinones. Furthermore, they were more stable than their precursor 4'-hydroxyallohumulinones during prolonged storage periods.

  2. Hard rectangles near curved hard walls: tuning the sign of the Tolman length

    CERN Document Server

    Sitta, Christoph E; Wittkowski, Raphael; Löwen, Hartmut

    2016-01-01

    Combining analytic calculations, computer simulations, and classical density functional theory we determine the interfacial tension of orientable two-dimensional hard rectangles near a curved hard wall. Both a circular cavity holding the particles and a hard circular obstacle surrounded by particles are considered. We focus on moderate bulk densities (corresponding to area fractions up to 50 percent) where the bulk phase is isotropic and vary the aspect ratio of the rectangles and the curvature of the wall. The Tolman length, which gives the leading curvature correction of the interfacial tension, is found to change sign at a finite density, which can be tuned via the aspect ratio of the rectangles.

  3. Hardness and wear properties of laminated Cr-Ni coatings formed by electroplating

    Science.gov (United States)

    Riyadi, Tri Widodo Besar; Masyrukan

    2017-04-01

    In this work, a laminated structure of Cr-Ni coating was prepared using electroplating on carbon steel substrates. Two baths of chrome and nickel electrolyte solutions were prepared to deposit laminated Cr and Ni layers. Chrome was firstly plated on a steel substrate in constant routes whereas nickel was subsequently electroplated on the Cr coating using varied plating times. The effect of Ni plating time on the thickness, hardness and wear specific of the Ni layer was investigated. The results show that an increase of plating times increased the thickness and hardness of the Ni layer, but reduced the wear specific. This study showed that Ni can be a potential candidate as a material replacement for chromium plating maintenance.

  4. Hardness of materials: studies at levels from atoms to crystals

    Institute of Scientific and Technical Information of China (English)

    LI KeYan; XUE DongFeng

    2009-01-01

    Based on the electron-holding energy per unit volume, we extend the concept of hardness to atomic stiffness, ionic stiffness and bond hardness, investigating the nature of material hardness at these three levels. We find that the stiffness of isolated atoms or ions has no direct connection with the hardness of materials, whereas material hardness is directly related to bond hardness, which is es-sentially determined by the electron-holding energy of its constituent chemical bonds per unit volume. We establish a model for identifying the hardness of materials on the basis of bond hardness. This work offers a deeper understanding of the nature of material hardness at the atomic level, and provides a practical guide in the search for new superhard materials.

  5. Biologically Active Polycaprolactone/Titanium Hybrid Electrospun Nanofibers for Hard Tissue Engineering

    DEFF Research Database (Denmark)

    Barakat, Nasser A. M.; Sheikh, Faheem A.; Al-Deyab, Salem S.

    2011-01-01

    In this study, a novel strategy to improve the bioactivity of polycaprolactone nanofibers is proposed. Incorporation of pure titanium nanoparticles into polycaprolactone nanofibers strongly enhances the precipitation of bone-like apatite materials when the doped nanofibers are soaked in a simulat...... nanofiber mats and the successful incorporation of the titanium nanoparticles make the prepared polycaprolactone nanofiber mat a proper candidate for the hard-tissue engineering applications....

  6. Monocular distance estimation with optical flow maneuvers and efference copies: a stability-based strategy.

    Science.gov (United States)

    de Croon, Guido C H E

    2016-01-07

    The visual cue of optical flow plays an important role in the navigation of flying insects, and is increasingly studied for use by small flying robots as well. A major problem is that successful optical flow control seems to require distance estimates, while optical flow is known to provide only the ratio of velocity to distance. In this article, a novel, stability-based strategy is proposed for monocular distance estimation, relying on optical flow maneuvers and knowledge of the control inputs (efference copies). It is shown analytically that given a fixed control gain, the stability of a constant divergence control loop only depends on the distance to the approached surface. At close distances, the control loop starts to exhibit self-induced oscillations. The robot can detect these oscillations and hence be aware of the distance to the surface. The proposed stability-based strategy for estimating distances has two main attractive characteristics. First, self-induced oscillations can be detected robustly by the robot and are hardly influenced by wind. Second, the distance can be estimated during a zero divergence maneuver, i.e., around hover. The stability-based strategy is implemented and tested both in simulation and on board a Parrot AR drone 2.0. It is shown that the strategy can be used to: (1) trigger a final approach response during a constant divergence landing with fixed gain, (2) estimate the distance in hover, and (3) estimate distances during an entire landing if the robot uses adaptive gain control to continuously stay on the 'edge of oscillation.'

  7. Influence of heat treatment on microstructures and micro-hardness of n-SiO2/Ni composite coating

    Institute of Scientific and Technical Information of China (English)

    XU Bin-shi; WANG Hai-dou; DONG Shi-yun; JIANG Bin; TU Wei-yi

    2004-01-01

    The n-SiO2/Ni composite electro-brush plating coating was prepared on the 1045 steel substrate. SEM and TEM were utilized to analyze the surface and cross-section morphologies or the microstructures of the composite coating before and after heat treatment, as well as a micro-hardness tester was used to measure the micro-hardness before and after heat treatment. The results show that the entrance of nano SiO2 particles into composite coating makes the micro-hardness higher. After heat treatment, due to the obstruction to growth of Ni crystals from nano particles, the composite coating still possesses a higher micro-hardness than that of common Ni-base coating.

  8. Aespoe hard rock laboratory. Annual report 2000

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    The Aespoe Hard Rock Laboratory constitutes an important component of SKB's work to design, construct, and implement a deep geological repository for spent nuclear fuel and to develop and test methods for characterisation of selected repository sites. The retention effect of the rock has been studied by tracer tests in the Tracer Retention Understanding Experiments (TRUE) and the TRUE Block Scale (TRUE BS). These tests are supplemented by the new Long Term Diffusion Experiment (LTDE). During year 2000 the field experiments of TRUE BS (50 m scale) were completed and preparations made for the LTDE (migration through a fracture wall and into the rock), including boring of approximately 10 m deep hole with 300 mm diameter. Laboratory investigations have difficulties in simulating natural conditions and need supplementary field studies to support validation exercises. A special borehole probe, CHEMLAB, has therefore been designed for different kinds of validation experiments where data can be obtained representative for the in-situ properties of groundwater at repository depth. During 2000 migration experiments were made with actinides (Am, Np and Pu) in CHEMLAB 2, the simplified supplement to CHEMLAB 1. Colloids of nuclides as well as of bentonite might affect the migration of released radionuclides and a separate project was planned during 2000 to assess the existence, stability and mobility of colloids. The development of numerical modelling tools continues with the general objective to improve the numerical models in terms of flow and transport and to update the site-scale and laboratory scale models for the Aespoe HRL. The Matrix Fluid Chemistry project aims at determining the origin and age of matrix fluids and the experiment has been designed to sample matrix fluids from predetermined, isolated borehole sections by specialised equipment. The Aespoe HRL also has the task to demonstrate and perform full scale tests of the function of different components of

  9. Microbiological quality of soft, semi-hard and hard cheeses during the shelf-life

    Directory of Open Access Journals (Sweden)

    Josip Vrdoljak

    2016-03-01

    Full Text Available Cheeses as ready-to-eat food should be considered as a potential source of foodborne pathogens, primarily Listeria monocytogenes. The aim of present study was to determine the microbiological quality of soft, semi-hard and hard cheeses during the shelf-life, with particular reference to L. monocytogenes. Five types of cheeses were sampled at different timepoints during the cold storage and analyzed for presence of Salmonella and L. monocytogenes, as well as lactic acid bacteria, Escherichia coli, coagulase-positive staphylococci, yeasts, molds, sulfite-reducing clostridia and L. monocytogenes counts. Water activity, pH and NaCl content were monitored in order to evaluate the possibility of L. monocytogenes growth. Challenge test for L. monocytogenes was performed in soft whey cheese, to determine the growth potential of pathogen during the shelf-life of product. All analyzed cheeses were compliant with microbiological criteria during the shelf-life. In soft cheeses, lactic acid bacteria increased in the course of the shelf-life period (1.2-2.6 log increase, while in semi-hard and hard cheeses it decreased (1.6 and 5.2 log decrease, respectively. Soft cheeses support the growth of L. monocytogenes according to determined pH values (5.8-6.5, water activity (0.99-0.94, and NaCl content (0.3-1.2%. Challenge test showed that L. monocytogenes growth potential in selected soft cheese was 0.43 log10 cfu/g during 8 days at 4°C. Water activity in semi-hard and hard cheeses was a limiting factor for Listeria growth during the shelf-life. Soft, semi-hard and hard cheeses were microbiologically stable during their defined shelf-life. Good manufacturing and hygienic practices must be strictly followed in the production of soft cheeses as Listeria-supporting food and be focused on preventing (recontamination.

  10. Bond-orientational analysis of hard-disk and hard-sphere structures.

    Science.gov (United States)

    Senthil Kumar, V; Kumaran, V

    2006-05-28

    We report the bond-orientational analysis results for the thermodynamic, random, and homogeneously sheared inelastic structures of hard-disks and hard-spheres. The thermodynamic structures show a sharp rise in the order across the freezing transition. The random structures show the absence of crystallization. The homogeneously sheared structures get ordered at a packing fraction higher than the thermodynamic freezing packing fraction, due to the suppression of crystal nucleation. On shear ordering, strings of close-packed hard-disks in two dimensions and close-packed layers of hard-spheres in three dimensions, oriented along the velocity direction, slide past each other. Such a flow creates a considerable amount of fourfold order in two dimensions and body-centered-tetragonal (bct) structure in three dimensions. These transitions are the flow analogs of the martensitic transformations occurring in metals due to the stresses induced by a rapid quench. In hard-disk structures, using the bond-orientational analysis we show the presence of fourfold order. In sheared inelastic hard-sphere structures, even though the global bond-orientational analysis shows that the system is highly ordered, a third-order rotational invariant analysis shows that only about 40% of the spheres have face-centered-cubic (fcc) order, even in the dense and near-elastic limits, clearly indicating the coexistence of multiple crystalline orders. When layers of close-packed spheres slide past each other, in addition to the bct structure, the hexagonal-close-packed (hcp) structure is formed due to the random stacking faults. Using the Honeycutt-Andersen pair analysis and an analysis based on the 14-faceted polyhedra having six quadrilateral and eight hexagonal faces, we show the presence of bct and hcp signatures in shear ordered inelastic hard-spheres. Thus, our analysis shows that the dense sheared inelastic hard-spheres have a mixture of fcc, bct, and hcp structures.

  11. Further links between the maximum hardness principle and the hard/soft acid/base principle: insights from hard/soft exchange reactions.

    Science.gov (United States)

    Chattaraj, Pratim K; Ayers, Paul W; Melin, Junia

    2007-08-07

    Ayers, Parr, and Pearson recently showed that insight into the hard/soft acid/base (HSAB) principle could be obtained by analyzing the energy of reactions in hard/soft exchange reactions, i.e., reactions in which a soft acid replaces a hard acid or a soft base replaces a hard base [J. Chem. Phys., 2006, 124, 194107]. We show, in accord with the maximum hardness principle, that the hardness increases for favorable hard/soft exchange reactions and decreases when the HSAB principle indicates that hard/soft exchange reactions are unfavorable. This extends the previous work of the authors, which treated only the "double hard/soft exchange" reaction [P. K. Chattaraj and P. W. Ayers, J. Chem. Phys., 2005, 123, 086101]. We also discuss two different approaches to computing the hardness of molecules from the hardness of the composing fragments, and explain how the results differ. In the present context, it seems that the arithmetic mean of fragment softnesses is the preferable definition.

  12. Is hyper-hardness more chemically relevant than expected?

    Science.gov (United States)

    Morell, Christophe; Grand, André; Toro-Labbé, Alejandro; Chermette, Henry

    2013-07-01

    In this work, the third derivative of the energy with respect to the number of electrons, the so-called hyper-hardness, is investigated to assess whether this quantity has a chemical meaning. To achieve this goal a new working expression for hyper-hardness is developed and analyzed. It transpired from this analysis that hyper-hardness, just like hardness, can measure the reactivity or the stability of electron systems. Interestingly, positive values of hyper-hardness point to quite stable species such as noble gases and molecules. On the other hand, radicals almost always display large negative values of hyper-hardness.

  13. Remember Hard But Think Softly: Metaphorical Effects of Hardness/Softness on Cognitive Functions

    Science.gov (United States)

    Xie, Jiushu; Lu, Zhi; Wang, Ruiming; Cai, Zhenguang G.

    2016-01-01

    Previous studies have found that bodily stimulation, such as hardness biases social judgment and evaluation via metaphorical association; however, it remains unclear whether bodily stimulation also affects cognitive functions, such as memory and creativity. The current study used metaphorical associations between “hard” and “rigid” and between “soft” and “flexible” in Chinese, to investigate whether the experience of hardness affects cognitive functions whose performance depends prospectively on rigidity (memory) and flexibility (creativity). In Experiment 1, we found that Chinese-speaking participants performed better at recalling previously memorized words while sitting on a hard-surface stool (the hard condition) than a cushioned one (the soft condition). In Experiment 2, participants sitting on a cushioned stool outperformed those sitting on a hard-surface stool on a Chinese riddle task, which required creative/flexible thinking, but not on an analogical reasoning task, which required both rigid and flexible thinking. The results suggest the hardness experience affects cognitive functions that are metaphorically associated with rigidity or flexibility. They support the embodiment proposition that cognitive functions and representations can be grounded in bodily states via metaphorical associations. PMID:27672373

  14. Hard-on-hard lubrication in the artificial hip under dynamic loading conditions.

    Directory of Open Access Journals (Sweden)

    Robert Sonntag

    Full Text Available The tribological performance of an artificial hip joint has a particularly strong influence on its success. The principle causes for failure are adverse short- and long-term reactions to wear debris and high frictional torque in the case of poor lubrication that may cause loosening of the implant. Therefore, using experimental and theoretical approaches models have been developed to evaluate lubrication under standardized conditions. A steady-state numerical model has been extended with dynamic experimental data for hard-on-hard bearings used in total hip replacements to verify the tribological relevance of the ISO 14242-1 gait cycle in comparison to experimental data from the Orthoload database and instrumented gait analysis for three additional loading conditions: normal walking, climbing stairs and descending stairs. Ceramic-on-ceramic bearing partners show superior lubrication potential compared to hard-on-hard bearings that work with at least one articulating metal component. Lubrication regimes during the investigated activities are shown to strongly depend on the kinematics and loading conditions. The outcome from the ISO gait is not fully confirmed by the normal walking data and more challenging conditions show evidence of inferior lubrication. These findings may help to explain the differences between the in vitro predictions using the ISO gait cycle and the clinical outcome of some hard-on-hard bearings, e.g., using metal-on-metal.

  15. Hard-on-hard lubrication in the artificial hip under dynamic loading conditions.

    Science.gov (United States)

    Sonntag, Robert; Reinders, Jörn; Rieger, Johannes S; Heitzmann, Daniel W W; Kretzer, J Philippe

    2013-01-01

    The tribological performance of an artificial hip joint has a particularly strong influence on its success. The principle causes for failure are adverse short- and long-term reactions to wear debris and high frictional torque in the case of poor lubrication that may cause loosening of the implant. Therefore, using experimental and theoretical approaches models have been developed to evaluate lubrication under standardized conditions. A steady-state numerical model has been extended with dynamic experimental data for hard-on-hard bearings used in total hip replacements to verify the tribological relevance of the ISO 14242-1 gait cycle in comparison to experimental data from the Orthoload database and instrumented gait analysis for three additional loading conditions: normal walking, climbing stairs and descending stairs. Ceramic-on-ceramic bearing partners show superior lubrication potential compared to hard-on-hard bearings that work with at least one articulating metal component. Lubrication regimes during the investigated activities are shown to strongly depend on the kinematics and loading conditions. The outcome from the ISO gait is not fully confirmed by the normal walking data and more challenging conditions show evidence of inferior lubrication. These findings may help to explain the differences between the in vitro predictions using the ISO gait cycle and the clinical outcome of some hard-on-hard bearings, e.g., using metal-on-metal.

  16. How Prepared is Prepared Enough?

    Science.gov (United States)

    Porter-Levy; Macleod; Rickert

    1996-10-01

    A 17-year-old female was in the final stage in treatment of right unilateral cleft lip and palate. She had undergone a number of previous surgeries. Hearing and speech were good on evaluation, and her social and family situation were deemed excellent. After preparatory orthodontics she underwent a Lefort I maxillary advancement. Surgery was successful and she was admitted into postoperative recovery. However, the lack of adequate preoperative preparation caused traumatic reaction from the patient and her parents: anxiety over appearance, crying, refusal of oral fluids and oral care, refusal of analgesia, and refusal to mobilize. The patience and persistence of hospital staff slowly overcame all adversities and the patient moved on to full and successful recovery, but this case prompted changes in preoperative procedures and involvement of patients and their families in postoperative meal selection, planing, and preparation.

  17. The Making of the Copy-cat City

    DEFF Research Database (Denmark)

    Ooi, Can-Seng

    2014-01-01

    , as if it were New York or London. Such comments can be considered flattering to the Chinese. Or the comments may merely reflect a lack of understanding of Shanghai. Or perhaps the comments are insulting because they insinuate that the Chinese metropolis is just another copy-cat city. Whatever the reason......, and the trendy bars like Bar Rouge and Mint. They have seen it all before, and the Shanghai they are visiting seems to lack a unique Chinese character. Today, places, particularly cities, broadly compete in terms of livability, economic opportunities, attractiveness, and vibrancy to attract international...... investors, businesses, visitors, talented workers, and audiences (Dinnie, 2011; Florida, 2002). This competition has also led to a proliferation of branded places. Places must stand out in the competition. So, in the place branding literature, the concern is differentiation and uniqueness (see various...

  18. Radiation and the classical double copy for color charges

    Science.gov (United States)

    Goldberger, Walter D.; Ridgway, Alexander K.

    2017-06-01

    We construct perturbative classical solutions of the Yang-Mills equations coupled to dynamical point particles carrying color charge. By applying a set of color to kinematics replacement rules first introduced by Bern, Carrasco and Johansson, these are shown to generate solutions of d -dimensional dilaton gravity, which we also explicitly construct. Agreement between the gravity result and the gauge theory double copy implies a correspondence between non-Abelian particles and gravitating sources with dilaton charge. When the color sources are highly relativistic, dilaton exchange decouples, and the solutions we obtain match those of pure gravity. We comment on possible implications of our findings to the calculation of gravitational waveforms in astrophysical black hole collisions, directly from computationally simpler gluon radiation in Yang-Mills theory.

  19. Radiation and the classical double copy for color charges

    CERN Document Server

    Goldberger, Walter D

    2016-01-01

    We construct perturbative classical solutions of the Yang-Mills equations coupled to dynamical point particles carrying color charge. By applying a set of color to kinematics replacement rules first introduced by Bern, Carrasco and Johansson (BCJ), these are shown to generate solutions of d-dimensional dilaton gravity, which we also explicitly construct. Agreement between the gravity result and the gauge theory double copy implies a correspondence between non-Abelian particles and gravitating sources with dilaton charge. When the color sources are highly relativistic, dilaton exchange decouples, and the solutions we obtain match those of pure gravity. We comment on possible implications of our findings to the calculation of gravitational waveforms in astrophysical black hole collisions, directly from computationally simpler gluon radiation in Yang-Mills theory.

  20. Template-Directed Biopolymerization: Tape-Copying Turing Machines

    Science.gov (United States)

    Sharma, Ajeet K.; Chowdhury, Debashish

    2012-10-01

    DNA, RNA and proteins are among the most important macromolecules in a living cell. These molecules are polymerized by molecular machines. These natural nano-machines polymerize such macromolecules, adding one monomer at a time, using another linear polymer as the corresponding template. The machine utilizes input chemical energy to move along the template which also serves as a track for the movements of the machine. In the Alan Turing year 2012, it is worth pointing out that these machines are "tape-copying Turing machines". We review the operational mechanisms of the polymerizer machines and their collective behavior from the perspective of statistical physics, emphasizing their common features in spite of the crucial differences in their biological functions. We also draw the attention of the physics community to another class of modular machines that carry out a different type of template-directed polymerization. We hope this review will inspire new kinetic models for these modular machines.

  1. Template-directed biopolymerization: tape-copying Turing machines

    CERN Document Server

    Sharma, Ajeet K; 10.1142/S1793048012300083

    2013-01-01

    DNA, RNA and proteins are among the most important macromolecules in a living cell. These molecules are polymerized by molecular machines. These natural nano-machines polymerize such macromolecules, adding one monomer at a time, using another linear polymer as the corresponding template. The machine utilizes input chemical energy to move along the template which also serves as a track for the movements of the machine. In the Alan Turing year 2012, it is worth pointing out that these machines are "tape-copying Turing machines". We review the operational mechanisms of the polymerizer machines and their collective behavior from the perspective of statistical physics, emphasizing their common features in spite of the crucial differences in their biological functions. We also draw attention of the physics community to another class of modular machines that carry out a different type of template-directed polymerization. We hope this review will inspire new kinetic models for these modular machines.

  2. Adapting Experiential Learning to Develop Problem-Solving Skills in Deaf and Hard-of-Hearing Engineering Students

    Science.gov (United States)

    Marshall, Matthew M.; Carrano, Andres L.; Dannels, Wendy A.

    2016-01-01

    Individuals who are deaf and hard-of-hearing (DHH) are underrepresented in science, technology, engineering, and mathematics (STEM) professions, and this may be due in part to their level of preparation in the development and retention of mathematical and problem-solving skills. An approach was developed that incorporates experiential learning and…

  3. Harnessing the advantages of hard and soft colloids by the use of core-shell particles as interfacial stabilizers

    NARCIS (Netherlands)

    Buchcic, C.; Tromp, R.H.; Meinders, M.B.J.; Cohen Stuart, M.A.

    2017-01-01

    The ability of colloidal particles to penetrate fluid interfaces is a crucial factor in the preparation of particle stabilized disperse systems such as foams and emulsions. For hard micron-sized particles the insertion into fluid interfaces requires substantial energy input, but soft particles

  4. Hard sludge removal in steam generators

    Energy Technology Data Exchange (ETDEWEB)

    Santibanez, M.; Stoss, J.

    2013-07-01

    One of the majors problems during the life of Nuclear power plants is the efficiency lost in steam generator due to, among issues, the plugging and therefore useless, of tubes which presented possibility of cracking in the future. The hard sludge produced in the steam generators secondary side and deposited on the tube sheet or around the tubes as collar shape are one of the main agent causing this problem, so their elimination is considered a major topic in order to keep the steam generators in an optimum condition along the whole plant life. AREVA is aware of this global problem, therefore a process and tools have been continuously developed since 1995 in order to eliminate the hard deposits in a effective way, with no damage to steam generator's components and adaptable for the different steam generators models existing in the market.

  5. Locating phase transitions in computationally hard problems

    Indian Academy of Sciences (India)

    B Ashok; T K Patra

    2010-09-01

    We discuss how phase-transitions may be detected in computationally hard problems in the context of anytime algorithms. Treating the computational time, value and utility functions involved in the search results in analogy with quantities in statistical physics, we indicate how the onset of a computationally hard regime can be detected and the transit to higher quality solutions be quantified by an appropriate response function. The existence of a dynamical critical exponent is shown, enabling one to predict the onset of critical slowing down, rather than finding it after the event, in the specific case of a travelling salesman problem (TSP). This can be used as a means of improving efficiency and speed in searches, and avoiding needless computations.

  6. Hard diffraction with dynamic gap survival

    Science.gov (United States)

    Rasmussen, Christine O.; Sjöstrand, Torbjörn

    2016-02-01

    We present a new framework for the modelling of hard diffraction in pp and poverline{p} collisions. It starts from the the approach pioneered by Ingelman and Schlein, wherein the single diffractive cross section is factorized into a Pomeron flux and a Pomeron PDF. To this it adds a dynamically calculated rapidity gap survival factor, derived from the modelling of multiparton interactions. This factor is not relevant for diffraction in ep collisions, giving non-universality between HERA and Tevatron diffractive event rates. The model has been implemented in P ythia 8 and provides a complete description of the hadronic state associated with any hard single diffractive process. Comparisons with poverline{p} and pp data reveal improvement in the description of single diffractive events.

  7. Hardness/intensity correlations among BATSE bursts

    Science.gov (United States)

    Paciesas, William S.; Pendleton, Geoffrey N.; Kouveliotou, Chryssa; Fishman, Gerald J.; Meegan, Charles A.; Wilson, Robert B.

    1992-01-01

    Conclusions about the nature of gamma-ray bursts derived from the size-frequency distribution may be altered if a significant correlation exists between burst intensity and spectral shape. Moreover, if gamma-ray bursts have a cosmological origin, such a correlation may be expected to result from the expansion of the universe. We have performed a rudimentary search of the BATSE bursts for hardness/intensity correlations. The range of spectral shapes was determined for each burst by computing the ratio of the intensity in the range 100-300 keV to that in 55-300 keV. We find weak evidence for the existence of a correlation, the strongest effect being present when comparing the maximum hardness ratio for each burst with its maximum rate.

  8. SURFACES OF HARD-SPHERE SYSTEMS

    Directory of Open Access Journals (Sweden)

    Dietrich Stoyan

    2014-07-01

    Full Text Available In various situations surfaces appear that are formed by systems of hard spheres. Examples are porous layers as surfaces of sand heaps and biofilms or fracture surfaces of concrete. The present paper considers models where a statistically homogeneous system of hard spheres with random radii is intersected by a plane and the surface is formed by the spheres with centers close to this plane. Formulae are derived for various characteristics of such surfaces: for the porosity profile, i.e. the local porosity in dependence on the distance from the section plane and for the geometry of the sphere caps that look above the section plane.It turns out that these characteristics only depend on the first-order characteristics of the sphere system, its sphere density and the sphere radius distribution.Comparison with empirically studied biofilms shows that the model is realistic.

  9. Quantitative Information Flow - Verification Hardness and Possibilities

    CERN Document Server

    Yasuoka, Hirotoshi

    2010-01-01

    Researchers have proposed formal definitions of quantitative information flow based on information theoretic notions such as the Shannon entropy, the min entropy, the guessing entropy, and channel capacity. This paper investigates the hardness and possibilities of precisely checking and inferring quantitative information flow according to such definitions. We prove that, even for just comparing two programs on which has the larger flow, none of the definitions is a k-safety property for any k, and therefore is not amenable to the self-composition technique that has been successfully applied to precisely checking non-interference. We also show a complexity theoretic gap with non-interference by proving that, for loop-free boolean programs whose non-interference is coNP-complete, the comparison problem is #P-hard for all of the definitions. For positive results, we show that universally quantifying the distribution in the comparison problem, that is, comparing two programs according to the entropy based definit...

  10. "Good-Walker" + QCD dipoles = Hard Diffraction

    CERN Document Server

    Peschanski, R

    1998-01-01

    The Good-Walker mechanism for diffraction is shown to provide a link between total and diffractive structure functions and to be relevant for QCD calculations at small x_{Bj}. For Deep-Inelastic scattering on a small-size target (cf. an onium) the r\\^ ole of Good-Walker ``diffractive eigenstates'' is played by the QCD dipoles appearing in the $1/N_C$ limit of QCD. Hard diffraction is thus related to the QCD tripe-dipole vertex which has been recently identified (and calculated) as being a conformal invariant correlator and/or a closed-string amplitude. An extension to hard diffraction at HERA via $k_T-$factorisation of the proton vertices leads to interesting phenomenology.

  11. Simulations of driven overdamped frictionless hard spheres

    Science.gov (United States)

    Lerner, Edan; Düring, Gustavo; Wyart, Matthieu

    2013-03-01

    We introduce an event-driven simulation scheme for overdamped dynamics of frictionless hard spheres subjected to external forces, neglecting hydrodynamic interactions. Our event-driven approach is based on an exact equation of motion which relates the driving force to the resulting velocities through the geometric information characterizing the underlying network of contacts between the hard spheres. Our method allows for a robust extraction of the instantaneous coordination of the particles as well as contact force statistics and dynamics, under any chosen driving force, in addition to shear flow and compression. It can also be used for generating high-precision jammed packings under shear, compression, or both. We present a number of additional applications of our method.

  12. Hard Diffraction with Dynamic Gap Survival

    CERN Document Server

    Rasmussen, Christine O

    2015-01-01

    We present a new framework for the modelling of hard diffraction in pp and ppbar collisions. It starts from the the approach pioneered by Ingelman and Schlein, wherein the single diffractive cross section is factorized into a Pomeron flux and a Pomeron PDF. To this it adds a dynamically calculated rapidity gap survival factor, derived from the modelling of multiparton interactions. This factor is not relevant for diffraction in ep collisions, giving non-universality between HERA and Tevatron diffractive event rates. The model has been implemented in Pythia 8 and provides a complete description of the hadronic state associated with any hard single diffractive process. Comparisons with ppbar and pp data reveal improvement in the description of single diffractive events.

  13. Hard exclusive reactions and generalized parton distributions

    Directory of Open Access Journals (Sweden)

    Hayrapetyan Avetik

    2015-01-01

    Full Text Available The recently developed formalism of Generalized Parton Distributions (GPDs allows connecting the experimental information of hard exclusive reactions to the spin contribution and even to the angular momentum contribution of quarks in the nucleon. By selecting different quantum numbers of the final state in exclusive productions, different GPDs can be addressed separately. The HERMES experiment at the HERA ring at DESY (Hamburg made pioneering contributions and first constraints to Generalized Parton Distributions (GPDs, using hard exclusive vector meson production (EVMP and Deeply Virtual Compton Scattering (DVCS. Using a novel recoil detector, HERMES managed to measure DVCS and EVMP free of any significant background. Selected results are highlighted and discussed in this paper.

  14. Structure of Coatomer Cage Proteins and the Relationship among COPI, COPII, and Clathrin Vesicle Coats

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Changwook; Goldberg, Jonathan (MSKCC)

    2010-09-13

    COPI-coated vesicles form at the Golgi apparatus from two cytosolic components, ARF G protein and coatomer, a heptameric complex that can polymerize into a cage to deform the membrane into a bud. Although coatomer shares a common evolutionary origin with COPII and clathrin vesicle coat proteins, the architectural relationship among the three cages is unclear. Strikingly, the {alpha}{beta}-COP core of coatomer crystallizes as a triskelion in which three copies of a {beta}-COP {beta}-propeller domain converge through their axial ends. We infer that the trimer constitutes the vertex of the COPI cage. Our model proposes that the COPI cage is intermediate in design between COPII and clathrin: COPI shares with clathrin an arrangement of three curved {alpha}-solenoid legs radiating from a common center, and COPI shares with COPII highly similar vertex interactions involving the axial ends of {beta}-propeller domains.

  15. Quantitative assessment of impairment in constructional ability by cube copying in patients with aphasia.

    Science.gov (United States)

    Maeshima, Shinichiro; Ueyoshi, Akitaka; Matsumoto, Tomoko; Boh-Oka, Shin-Ichi; Yoshida, Munehito; Itakura, Toru

    2002-02-01

    Constructional apraxia was evaluated in patients with aphasia using a cube-copying task. It was assessed whether quantitative assessment of cube copying could be used to estimate the performance intelligence quotient (IQ) according to neuropsychological tests. Abnormality in the cube-copying test was observed in 42 of 46 patients (91.3%). Performance according to Raven's coloured progressive matrices and the revised Wechshler adult intelligence scale (WAIS-R) in patients with poor cube copying was significantly lower than in the other four patients. Numbers of the connections completed and plane-orientation errors made in the cube-copying test were significantly correlated with performance IQ on the WAIS-R, correlating particularly with block design, digit symbol, and object assembly in performance IQ subtests. The quantitatively scored cube-copying test, then, can roughly predict non-verbal IQ in patients with aphasia.

  16. Entanglement Preserving in Quantum Copying of Three-Qubit Entangled State

    Institute of Scientific and Technical Information of China (English)

    TONGZhao-Yang; KUANGLe-Man

    2002-01-01

    We study the degree to which quantum entanglement survives when a three-qubit entangled state is copied by using local and non-local processes,respectively,and investigate iterating quantum copying for the three-qubit system.There may exist inter-three-qubit entanglement and inter-two-qubit entanglement for the three-qubit system.We show that both local and non-local copying processes degrade quantum entanglement in the three-particle system due to a residual correlation between the copied output and the copying machine.we also show that the inter-two-qubit entanglement is preserved better than the inter-three-qubit entanglement in the local cloning process.We find that non-local cloning is much more efficient than the local copying for broadcasting entanglement,and output state via non-local cloning exhiits the fidelity better than local cloning.

  17. Copy Chic: Status Representation and Intellectual Property Rights in Contemporary Fashion

    DEFF Research Database (Denmark)

    Mackinney-Valentin, Maria; Teilmann-Lock, Stina

    2014-01-01

    Copying in fashion has a variety of meanings and implications. Copying is socially, creatively and commercially ingrained in the very nature of fashion. Consumers copy early-adopters in an ongoing process of style emulation. Designers are inspired by the world around them, including other designers....... And the luxury fashion industry has historically benefited from mass-market as a way of stimulating consumers’ appetite for innovation. The article explores the presence of “copy chic” in luxury fashion as an ambiguous celebration of the conspicuously inauthentic through a study of luxury version...... of the inexpensive, plaid bag often referred to as a “Chinatown tote.” The article explores fashion copying from an interdisciplinary position integrating legal and consumer perspectives within the framework of the luxury fashion industry. It will be proposed that the regulation of copying in luxury fashion takes...

  18. Copy number variants in the kallikrein gene cluster.

    Directory of Open Access Journals (Sweden)

    Pernilla Lindahl

    Full Text Available The kallikrein gene family (KLK1-KLK15 is the largest contiguous group of protease genes within the human genome and is associated with both risk and outcome of cancer and other diseases. We searched for copy number variants in all KLK genes using quantitative PCR analysis and analysis of inheritance patterns of single nucleotide polymorphisms. Two deletions were identified: one 2235-bp deletion in KLK9 present in 1.2% of alleles, and one 3394-bp deletion in KLK15 present in 4.0% of alleles. Each deletion eliminated one complete exon and created out-of-frame coding that eliminated the catalytic triad of the resulting truncated gene product, which therefore likely is a non-functional protein. Deletion breakpoints identified by DNA sequencing located the KLK9 deletion breakpoint to a long interspersed element (LINE repeated sequence, while the deletion in KLK15 is located in a single copy sequence. To search for an association between each deletion and risk of prostate cancer (PC, we analyzed a cohort of 667 biopsied men (266 PC cases and 401 men with no evidence of PC at biopsy using short deletion-specific PCR assays. There was no association between evidence of PC in this cohort and the presence of either gene deletion. Haplotyping revealed a single origin of each deletion, with most recent common ancestor estimates of 3000-8000 and 6000-14 000 years for the deletions in KLK9 and KLK15, respectively. The presence of the deletions on the same haplotypes in 1000 Genomes data of both European and African populations indicate an early origin of both deletions. The old age in combination with homozygous presence of loss-of-function variants suggests that some kallikrein-related peptidases have non-essential functions.

  19. Decoding NF1 Intragenic Copy-Number Variations.

    Science.gov (United States)

    Hsiao, Meng-Chang; Piotrowski, Arkadiusz; Callens, Tom; Fu, Chuanhua; Wimmer, Katharina; Claes, Kathleen B M; Messiaen, Ludwine

    2015-08-06

    Genomic rearrangements can cause both Mendelian and complex disorders. Currently, several major mechanisms causing genomic rearrangements, such as non-allelic homologous recombination (NAHR), non-homologous end joining (NHEJ), fork stalling and template switching (FoSTeS), and microhomology-mediated break-induced replication (MMBIR), have been proposed. However, to what extent these mechanisms contribute to gene-specific pathogenic copy-number variations (CNVs) remains understudied. Furthermore, few studies have resolved these pathogenic alterations at the nucleotide-level. Accordingly, our aim was to explore which mechanisms contribute to a large, unique set of locus-specific non-recurrent genomic rearrangements causing the genetic neurocutaneous disorder neurofibromatosis type 1 (NF1). Through breakpoint-spanning PCR as well as array comparative genomic hybridization, we have identified the breakpoints in 85 unrelated individuals carrying an NF1 intragenic CNV. Furthermore, we characterized the likely rearrangement mechanisms of these 85 CNVs, along with those of two additional previously published NF1 intragenic CNVs. Unlike the most typical recurrent rearrangements mediated by flanking low-copy repeats (LCRs), NF1 intragenic rearrangements vary in size, location, and rearrangement mechanisms. We propose the DNA-replication-based mechanisms comprising both FoSTeS and/or MMBIR and serial replication stalling to be the predominant mechanisms leading to NF1 intragenic CNVs. In addition to the loop within a 197-bp palindrome located in intron 40, four Alu elements located in introns 1, 2, 3, and 50 were also identified as intragenic-rearrangement hotspots within NF1.

  20. Germline copy number variation and ovarian cancer survival

    Directory of Open Access Journals (Sweden)

    Brooke L Fridley

    2012-08-01

    Full Text Available Copy number variants (CNVs have been implicated in many complex diseases. We examined whether inherited CNVs were associated with overall survival among women with invasive epithelial ovarian cancer. Germline DNA from 1,056 cases (494 deceased, average of 3.7 years follow-up was interrogated with the Illumina 610quad genome-wide array containing, after quality control exclusions, 581,903 single nucleotide polymorphisms (SNPs and 17,917 CNV probes. Comprehensive analysis capitalized upon the strengths of three complementary approaches to CNV classification. First, to identify small CNVs, single markers were evaluated and, where associated with survival, consecutive markers were combined. Two chromosomal regions were associated with survival using this approach (14q31.3 rs2274736 p=1.59x10-6, p=0.001; 22q13.31 rs2285164 p=4.01x10-5, p=0.009, but were not significant after multiple testing correction. Second, to identify large CNVs, genome-wide segmentation was conducted to characterize chromosomal gains and losses, and association with survival was evaluated by segment. Four regions were associated with survival (1q21.3 loss p=0.005, 5p14.1 loss p=0.004, 9p23 loss p=0.002, and 15q22.31 gain p=0.002; however, again, after correcting for multiple testing, no regions were statistically significant, and none were in common with the single-marker approach. Finally, to evaluate associations with general amounts of copy number changes across the genome, we estimated CNV burden based on genome-wide numbers of gains and losses; no associations with survival were observed (p>0.40. Although CNVs that were not well-covered by the Illumina 610quad array merit investigation, these data suggest no association between inherited CNVs and survival after ovarian cancer.