WorldWideScience

Sample records for prepared calcium phosphate

  1. Preparation and characterization of calcium phosphate biomaterials.

    Science.gov (United States)

    Calafiori, A R; Di Marco, G; Martino, G; Marotta, M

    2007-12-01

    Calcium phosphate cement (CPC) samples have been prepared with a mixture of monocalciumphosphate monohydrate (MCPM) and calcium carbonate (CC) powders, in stechiometric moles ratio 1:2.5 to obtain a Ca/P ratio of about 1.67 typical of hydroxyapatite (HAp), with or without addition of HAp. All specimens are incubated at 30 degrees C in a steam saturated air environment for 3, 6 and 15 days respectively, afterwards dried and stored under nitrogen. The calcium phosphate samples have been characterized by X-ray diffraction (XRD), Vickers hardness test (HV), diametral compression (d.c.), strength compression, and porosity evaluation. MCPM/CC mixture has a 30% HAp final concentration and is characterized by higher porosity (amount 78%) and mechanical properties useful as filler in bone segments without high mechanical stress.

  2. Preparation of Porous Calcium Phosphate Bioceramic

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Porous calcium phosphate ceramics were prepared by slip casting and molding method respectively. By these two different methods, different microstructures can be got. By slip casting method, the pore size was 100- 350μm and 20- 80μm; pores were opened, interconnected and ball-like; the grain size was 2- 4 μm.By molding method, the pore size was 100-500 μm and 1-10μm; the grain size was 2-8μm. By slip casting method regular and interconnected pores can be got. By molding method the porosity and strength can be adjusted easily.

  3. Hydrothermal method for preparing calcium phosphate monoliths

    Directory of Open Access Journals (Sweden)

    García Carrodeguas Raúl

    2003-01-01

    Full Text Available A new hydrothermal route for preparing biphasic calcium phosphate monoliths is proposed. Firstly, a slurry of beta-tricalcium phosphate/ortho-phosphoric acid (b-TCP/H3PO4 is cast into the desired final shape and size to obtain a block composed of dicalcium phosphate dihydrate (DCPD and b-TCP. This block is then treated in 1.0 M Na2HPO4 at 60 °C in order to hydrolyze the DCPD into Ca10-x(HPO4x(PO4 6-x(OH2-x (CDHA and Ca8H2(PO46 .5H2O (OCP. The result is a monolithic piece which preserves the initial shape and size, but which is composed instead of CDHA, OCP, and b-TCP. During the initial stage, when the pH is slightly alkaline, the product of DCPD hydrolysis is CDHA. However, when a neutral or slightly acidic pH is reached OCP is formed. Test samples processed by this method showed complete conversion of DCPD into CDHA and OCP after 112 h of hydrolysis, and with a compressive strength of 16.2 MPa, similar to cancellous bone.

  4. Preparation and characterization of bioceramics produced from calcium phosphate cements

    Energy Technology Data Exchange (ETDEWEB)

    Andriotis, O.; Katsamenis, O.L. [Department of Materials Science, University of Patras, 26504, Patras (Greece); Mouzakis, D.E. [Technological Educational Institute of Larisa, Department of Mechanical Engineering, T.E.I of Larissa, 411 10, Larissa (Greece); Bouropoulos, N. [Foundation for Research and Technology, Hellas, Institute of Chemical Engineering and High Temperature Chemical Processes, FORTH/ICE-HT, P.O. Box 1414, 26504 Rio Patras (Greece)

    2010-03-15

    The present work reports a method for preparing calcium phosphate ceramics by calcination of calcium phosphate cements composed mainly of calcium deficient hydroxyapatite (CDHA). It was found that hardened cements calcinied at temperatures from to 600 to 1300 C were transformed to tricalcium phosphates. Moreover the compressive strength was determined and porosity was estimated as a function of the calcination temperature. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  5. Preparation and Characterization of Porous Calcium Phosphate Bioceramics

    Institute of Scientific and Technical Information of China (English)

    Honglian Dai; Xinyu Wang; Yinchao Han; Xin Jiang; Shipu Li

    2011-01-01

    β-tricalcium phosphate (β-TCP) powder and Na2O-CaO-MgO-P2O5 glass binder were synthesized and mixed, and then the biodegradable porous calcium phosphate ceramics were successfully prepared by foaming and sintering at 850℃. The as-prepared ceramics possess a high porosity with partial three-dimension interconnected macro- and micro-pores. As in vitro experiment testified, the calcium phosphate ceramics (CPCs) has good degradability.

  6. Preparation of DNA/Gold Nanoparticle Encapsulated in Calcium Phosphate

    Directory of Open Access Journals (Sweden)

    Tomoko Ito

    2011-01-01

    Full Text Available Biocompatible DNA/gold nanoparticle complex with a protective calcium phosphate (CaP coating was prepared by incubating DNA/gold nanoparticle complex coated by hyaluronic acid in SBF (simulated body fluid with a Ca concentration above 2 mM. The CaP-coated DNA complex was revealed to have high compatibility with cells and resistance against enzymatic degradation. By immersion in acetate buffer (pH 4.5, the CaP capsule released the contained DNA complex. This CaP capsule including a DNA complex is promising as a sustained-release system of DNA complexes for gene therapy.

  7. Calcium phosphate bioceramics prepared from wet chemically precipitated powders

    Directory of Open Access Journals (Sweden)

    Kristine Salma

    2010-03-01

    Full Text Available In this work calcium phosphates were synthesized by modified wet chemical precipitation route. Contrary to the conventional chemical precipitation route calcium hydroxide was homogenized with planetary mill. Milling calcium oxide and water in planetary ball mill as a first step of synthesis provides a highly dispersed calcium hydroxide suspension. The aim of this work was to study the influence of main processing parameters of wet chemical precipitation synthesis product and to control the morphology, phase and functional group composition and, consequently, thermal stability and microstructure of calcium phosphate bioceramics after thermal treatment. The results showed that it is possible to obtain calcium phosphates with different and reproducible phase compositions after thermal processing (hydroxyapatite [HAp], β-tricalcium phosphate [β-TCP] and HAp/β-TCP by modified wet-chemical precipitation route. The β-TCP phase content in sintered bioceramics samples is found to be highly dependent on the changes in technological parameters and it can be controlled with ending pH, synthesis temperature and thermal treatment. Pure, crystalline and highly thermally stable (up to 1300°C HAp bioceramics with homogenous grainy microstructure, grain size up to 200–250 nm and high open porosity can be successfully obtained by powder synthesized at elevated synthesis temperature of 70°C and stabilizing ending pH at 9.

  8. Optimization of calcium phosphate fine ceramic powders preparation

    Science.gov (United States)

    Sezanova, K.; Tepavitcharova, S.; Rabadjieva, D.; Gergulova, R.; Ilieva, R.

    2013-12-01

    The effect of biomimetic synthesis method, reaction medium and further precursor treatments on the chemical and phase composition, crystal size and morphology of calcium phosphates was examined. Nanosized calcium phosphate precursors were biomimetically precipitated by the method of continuous precipitation in three types of reaction media at pH 8: (i) SBF as an inorganic electrolyte system; (ii) organic (glycerine) modified SBF (volume ratio of 1:1); (iii) polymer (10 g/l xanthan gum or 10 g/l guar gum) modified SBF (volume ratio of 1:1). After maturation (24 h) the samples were lyophilized, calcinated at 300°C for 3 hours, and washed with water, followed by new gelation, lyophilization and step-wise (200, 400, 600, 800, and 1000°C, each for 3 hours) sintering. The reaction medium influenced the chemical composition and particle size but not the morphology of the calcium phosphate powders. In all studied cases bi-phase calcium phosphate fine powders with well-shaped spherical grains, consisting of β-tricalcium phosphate (β-TCP) and hydroxyapatite (HA) with a Ca/P ratio of 1.3 - 1.6 were obtained. The SBF modifiers decreased the particle size of the product in the sequence guar gum ˜ xanthan gum < glycerin < SBF medium.

  9. Preparation and characterization of a novel injectable strontium-containing calcium phosphate cement with collagen

    OpenAIRE

    2015-01-01

    Purpose: To develop a novel injectable strontium-containing calcium phosphate cement with collagen. Methods: A novel calcium phosphate bone cement (CPC) was prepared with the addition of strontium element, collagenⅠ, and modified starch; the injectability, solidification time, microstructure, phase composition, compressive strength, anti-collapsibility and histological properties of material were evaluated. Results: The results showed that the material could be injected with an excellen...

  10. Preparation of in situ hardening composite microcarriers: calcium phosphate cement combined with alginate for bone regeneration.

    Science.gov (United States)

    Park, Jung-Hui; Lee, Eun-Jung; Knowles, Jonathan C; Kim, Hae-Won

    2014-03-01

    Novel microcarriers consisting of calcium phosphate cement and alginate were prepared for use as three-dimensional scaffolds for the culture and expansion of cells that are effective for bone tissue engineering. The calcium phosphate cement-alginate composite microcarriers were produced by an emulsification of the composite aqueous solutions mixed at varying ratios (calcium phosphate cement powder/alginate solution = 0.8-1.2) in an oil bath and the subsequent in situ hardening of the compositions during spherodization. Moreover, a porous structure could be easily created in the solid microcarriers by soaking the produced microcarriers in water and a subsequent freeze-drying process. Bone mineral-like apatite nanocrystallites were shown to rapidly develop on the calcium phosphate cement-alginate microcarriers under moist conditions due to the conversion of the α-tricalcium phosphate phase in the calcium phosphate cement into a carbonate-hydroxyapatite. Osteoblastic cells cultured on the microspherical scaffolds were proven to be viable, with an active proliferative potential during 14 days of culture, and their osteogenic differentiation was confirmed by the determination of alkaline phosphatase activity. The in situ hardening calcium phosphate cement-alginate microcarriers developed herein may be used as potential three-dimensional scaffolds for cell delivery and tissue engineering of bone.

  11. Preparation and mechanism of calcium phosphate coatings on chemical modified carbon fibers by biomineralization

    Institute of Scientific and Technical Information of China (English)

    HUANG Su-ping; ZHOU Ke-chao; LI Zhi-you

    2008-01-01

    In order to prepare HA coatings on the carbon fibers, chemical modification and biomineralization processes were applied. The phase components, morphologies, and possible growth mechanism of calcium phosphate were studied by infrared spectroscopy(IR), X-ray diffractometry(XRD) and scanning electron microscopy(SEM). The results show that calcium phosphate coating on carbon fibers can be obtained by biomineralization. But the phase components and morphologies of calcium phosphate coatings are different due to different modification methods. Plate-like CaHPO4-2H2O (DCPD) crystals grow from one site of the active centre by HNO3 treatment. While on the para-aminobenzoic acid treated fibers, the coating is composed of nano-structural HA crystal homogeneously. This is because the -COOH functional groups of para-aminobenzoic acid graft on fibers, with negative charge and arranged structure, accelerating the HA crystal nucleation and crystallization on the carbon fibers.

  12. Preparation and mechanical property of core-shell type chitosan/calcium phosphate composite fiber

    Energy Technology Data Exchange (ETDEWEB)

    Matsuda, Atsushi [Japan Society for the Promotion of Science, Ikenohata1-1-1, Daitou-ku, Tokyo 110-0008 (Japan) and Creative Research Initiative ' Sousei' , Hokkaido University, Sapporo, Hokkaido 001-0021 (Japan)]. E-mail: MATSUDA.Atsushi@nims.go.jp; Ikoma, Toshiyuki [Biomaterials Research Center, National Institute for Materials Science, Namiki 1-1, Tsukuba, Ibaraki 305-0044 (Japan); Kobayashi, Hisatoshi [Biomaterials Research Center, National Institute for Materials Science, Namiki 1-1, Tsukuba, Ibaraki 305-0044 (Japan)]. E-mail: Kobayashi.Hisatoshi@nims.go.jp; Tanaka, Junzo [Creative Research Initiative ' Sousei' , Hokkaido University, Sapporo, Hokkaido 001-0021 (Japan); Biomaterials Research Center, National Institute for Materials Science, Namiki 1-1, Tsukuba, Ibaraki 305-0044 (Japan)

    2004-12-01

    Core-shell type chitosan/calcium phosphate composite fibers were prepared by a facile wet spinning method; the chitosan aqueous solution with PO{sub 4} ions was dropped and coagulated in the ethanol/calcium hydroxide solutions at different mixed ratio. X-ray diffraction (XRD) patterns indicated that the crystal phases of calcium phosphates in the composite fibers were a low-crystalline hydroxyapatite (HAp; Ca{sub 10}(PO{sub 4}){sub 6}(OH){sub 2})or the low-crystalline hydroxyapatite/brushite mixture depended on the ratio of ethanol/calcium hydroxide solutions. The inorganic contents were ca. 60 wt.% by using the TG-DTA analysis. The energy-dispersive X-ray spectroscopy (EDS) analysis indicated that Ca and P atoms were mainly distributed on the outer layer of the composite fiber to grow calcium phosphate crystals; however, a little amount of P atom still remained at the inside of the fiber. This indicated that the composite fibers formed a unique core-shell structure with shell of calcium phosphate and core of chitosan. The mechanical property of the fibers was reinforced by the initial concentration of chitosan solution.

  13. Preparation and Properties of Nanoparticles of Calcium Phosphates With Various Ca/P Ratios.

    Science.gov (United States)

    Sun, Limin; Chow, Laurence C; Frukhtbeyn, Stanislav A; Bonevich, John E

    2010-01-01

    This study aimed at preparing and studying the properties of nanoparticles of calcium phosphate (nCaP) with Ca/P ratios ranging from 1.0 to 1.67 using a spray-drying technique. Micro-structural analyses suggested that the nCaPs with Ca/P ratios of 1.67 to 1.33 were nano-sized amorphous calcium phosphate (ACP) containing varying amounts of acid phosphate and carbonate. The nCaP with Ca/P ratio of 1 contained only nano-sized low crystalline dicalcium phosphate (DCP). BET measurements of the nCaPs showed specific surface areas of (12 ± 2 to 50 ± 1) m(2)/g, corresponding to estimated equivalent spherical diameters of (38 to 172) nm. However, dynamic light scattering measurements revealed much larger particles of (380 ± 49 to 768 ± 111) nm, owing to agglomeration of the smaller primary nano particles as revealed by Scanning Electron Microscopy (SEM). Thermodynamic solubility measurements showed that the nCaPs with Ca/P ratio of 1.33 - 1.67 all have similar solubility behavior. The materials were more soluble than the crystalline hydroxyapatite (HA) at pH greater than about 4.7, and more soluble than β-tricalcium phosphate (β-TCP), octacalcium phosphate (OCP) and DCP at pH above 5.5. Their solubility approached that of α-tricalcium phosphate (α-TCP) at about pH 7. These nCaPs, which cannot be readily prepared by other currently available methods for nanoparticle preparation, have potential biomedical applications.

  14. Europium-doped amorphous calcium phosphate porous nanospheres: preparation and application as luminescent drug carriers

    Directory of Open Access Journals (Sweden)

    Zhang Kui-Hua

    2011-01-01

    Full Text Available Abstract Calcium phosphate is the most important inorganic constituent of biological tissues, and synthetic calcium phosphate has been widely used as biomaterials. In this study, a facile method has been developed for the fabrication of amorphous calcium phosphate (ACP/polylactide-block-monomethoxy(polyethyleneglycol hybrid nanoparticles and ACP porous nanospheres. Europium-doping is performed to enable photoluminescence (PL function of ACP porous nanospheres. A high specific surface area of the europium-doped ACP (Eu3+:ACP porous nanospheres is achieved (126.7 m2/g. PL properties of Eu3+:ACP porous nanospheres are investigated, and the most intense peak at 612 nm is observed at 5 mol% Eu3+ doping. In vitro cytotoxicity experiments indicate that the as-prepared Eu3+:ACP porous nanospheres are biocompatible. In vitro drug release experiments indicate that the ibuprofen-loaded Eu3+:ACP porous nanospheres show a slow and sustained drug release in simulated body fluid. We have found that the cumulative amount of released drug has a linear relationship with the natural logarithm of release time (ln(t. The Eu3+:ACP porous nanospheres are bioactive, and can transform to hydroxyapatite during drug release. The PL properties of drug-loaded nanocarriers before and after drug release are also investigated.

  15. Preparation of Laminin-apatite-polymer Composites Using Metastable Calcium Phosphate Solutions

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    A synthetic polymer with a laminin-apatite composite layer on its surface would be useful as a percutaneous device. The preparation of such a composite was attempted in the present study using poly ( ethylene terephthalate ) (PET) and polyethylene ( PE ) as the synthetic polymer. PET and PE plates and those pretreated with an oxygen plasma were alternately dipped in calcium and phosphate ion solutions, and then immersed in a metastable ealcium phosphate solution supplemented with laminin ( LCP solution ). The PET and PE plates pretreated with an oxygen plasma formed a uniform and continuous layer of a laminin- apatite composite on their surfaces. In contrast, the PET and PE plates that had not been pretreated with an oxygen plasma did not form a continuous layer of a laminin-apatite composite on their surfaces. The hydrophilic functional groups on the PET and PE surfaces introduced by the plasma treatment were responsible for the successful laminin-apatite composite coating.

  16. Single step preparation of nanosilver loaded calcium phosphate by low temperature co-conversion process.

    Science.gov (United States)

    Suwanprateeb, J; Thammarakcharoen, F; Wasoontararat, K; Chokevivat, W; Phanphiriya, P

    2012-09-01

    The preparation and characterization of nanosilver loaded calcium phosphate aiming to enhance the bactericidal performance by a single step co-conversion technique using low temperature ion exchange phosphorization in combination with Tollen's reaction were performed. Silver nitrate was used as a silver ion supply source (0.001-0.1 M) and glucose was employed as a reducing agent. After conversion, surface and shell zones of all samples comprised hydroxyapatite and metallic silver as the main phases regardless of silver nitrate concentration. However, hydroxyapatite, residual calcium sulfate and monetite were found in the core zone when using silver nitrate concentration lower than 0.1 M. The microstructure of all samples comprised the distribution of spherical-shaped silver nanoparticles within the cluster of calcium phosphate nanocrystals. Total silver content (range, 0.09-6.5 %) in the converted samples was found to linearly increase with increasing silver nitrate content. Flexural modulus and strength of converted samples generally decreased with increasing silver content. Effective antibacterial activity of two selected samples (0.001 and 0.005 M AgNO(3)) against two bacterial strains (Pseudomonas aeruginosa and Staphylococcus aureus) was observed. Cytotoxic potentials by MTT assay of both samples were observed at 24 and 48 h extraction respectively.

  17. Preparation and characterization of a novel injectable strontium-containing calcium phosphate cement with collagen

    Directory of Open Access Journals (Sweden)

    Zhou Ziqiang

    2015-07-01

    Full Text Available Purpose: To develop a novel injectable strontium-containing calcium phosphate cement with collagen. Methods: A novel calcium phosphate bone cement (CPC was prepared with the addition of strontium element, collagenⅠ, and modified starch; the injectability, solidification time, microstructure, phase composition, compressive strength, anti-collapsibility and histological properties of material were evaluated. Results: The results showed that the material could be injected with an excellent performance; the modified starch significantly improved the anti-washout property of cement; with the liquid to solid ratio of 0.3, the largest compressive strength of cement was obtained (48.0 MPa ± 2.3 MPa; histological examination of repair tissue showed that the bone was repaired after 16 weeks; the degradation of cement was consistent with the new bone growth. Conclusion: A novel injectable collagen-strontium-containing CPC with excellent compressive strength and suitable setting time was prepared, with addition of modified starch. The CPC showed a good antiwashout property and the degradation time of the cement met with the new bone growing. This material is supposed to be used in orthopedic and maxillofacial surgery for bone defects.

  18. Synthesis of calcium phosphates and porous hydroxyapatite beads prepared by emulsion method

    Energy Technology Data Exchange (ETDEWEB)

    Chen, B.-H. [Faculty of Biotechnology, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Chen, K.-I [Department of Electronics Engineering and Computer Science, Tung-Fang Institute of Technology, 100 Dungfang Road, Hunei, Kaohsiung, Taiwan (China); Ho, M.-L. [Department of Physiology, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Chen, H.-N. [Faculty of Medicinal and Applied Chemistry, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China); Chen, W.-C. [Faculty of Dentistry, Kaohsiung Medical University, Kaohsiung 807, Taiwan (China); Wang, C.-K. [Faculty of Medicinal and Applied Chemistry, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 807, Taiwan (China)], E-mail: ckwang@kmu.edu.tw

    2009-01-15

    Raw calcium phosphates were synthesized via a chemical reaction between 0.5 M orthophosphoric acid and 0.5 M calcium hydroxide. Hydroxyapatite (HAp), {beta}-tricalcium phosphate ({beta}-TCP) or biphase calcium phosphate (BCP) comprising HAp and {beta}-TCP were obtained by changing pH value, Ca/P ratio, and the addition of glycerol. The as-synthesized and heat-treated powders were analyzed by X-ray diffraction (XRD) and Fourier transformation infrared spectrometry (FTIR). Thermal stability of the pure apatite phase was obtained to be 1300 deg. C, while synthesis was done at the pH value of 10.0 with a Ca/P ratio of 2.0 and a temperature of 37 deg. C. Besides, the {beta}-TCP phase (with higher purity) was achieved at 800 deg. C, whose synthesis was done at pH 6.4 with a Ca/P ratio of 1.5 and a temperature of 37 deg. C. Therefore, the biphase bioceramics comprising of HAp and {beta}-TCP could be obtained, since it was manipulated suitably. The HAp raw material was subjected to a simple emulsion method for the preparation of porous beads. They should have the advantage of exhibiting higher adsorptive ability and osteoconductivity in comparison with the sintered dense apatite. Additionally, the porous beads of apatite were demonstrated to be non-toxic to cells, and should be suitable for the use as a scaffold of cultured bone and bone graft material, as well as for drug delivery systems.

  19. Preparation of porous chitosan-poly(acrylic acid)-calcium phosphate hybrid nanoparticles via mineralization

    Institute of Scientific and Technical Information of China (English)

    CHEN ChangJing; DENG Yu; YAN ErYun; HU Yong; JIANG XiQun

    2009-01-01

    In this work,the preparation of chitosan-poly(acrylic acid)-calcium phosphate hybrid nanoparticles (CS-PAA-CaP NP) based on the mineralization of calcium phosphate (CAP) on the surface of chitosan-poly (acrylic acid) nanoparticles (CS-PAA NPs) was reported. CS-PAA-CaP NPs were achieved by directly adding ammonia to the aqueous solution of CS-PAA nanoparticles or by thermal decomposition of urea in the aqueous solution of CS-PAA nanoparticles,resulting in the mineralization of CaP on the surface of CS-PAA NPs. Through these two routes,especially using urea as a pH-regulator,the precipitation of CS-PAA NPs,a common occurrence in basic environment,was avoided. The size,morphology and ingredient of CS-PAA-CaP hybrid nanoparticles were characterized by dynamic light scattering (DLS),transmission electron microscope (TEM),scanning electron microscope (SEM),thermogravimetry analysis (TGA) and X-ray diffractometer (XRD). When urea was used as the pH regulator to facilitate the mineralization during the thermal urea decomposition procedure,regular CS-PAA-CaP hybrid nanoparticles with a porosity-structural CaP shells and 400-600 nm size were obtained. TGA result revealed that the hybrid NPs contained approximately 23% inorganic component,which was consistent with the ratio of starting materials. The XRD spectra of hybrid nanoparticles indicated that dicalcium phosphate (DCP:CaHPO4) crystal was a dominant component of mineralization.The porous structure of the CS-PAA-CaP hybrid NPs might be greatly useful in pharmaceutical and other medical applications.

  20. Preparation of tricalcium phosphate/calcium pyrophosphate structures via rapid prototyping.

    Science.gov (United States)

    Gbureck, Uwe; Hölzel, Tanja; Biermann, Isabell; Barralet, Jake E; Grover, Liam M

    2008-04-01

    Custom made tricalcium phosphate/calcium pyrophosphate bone substitutes with a well-defined architecture were fabricated in this study using 3D powder printing with tricalcium phosphate (TCP) powder and a liquid phase of phosphoric acid. The primary formed matrix of dicalcium phosphate dihydrate (DCPD, brushite) was converted in a second step to calcium pyrophosphate (CPP) by heat treatment in the temperature range 1,100-1,300 degrees C. The structures exhibited compressive strengths between 0.8 MPa and 4 MPa after sintering at 1,100-1,250 degrees C, higher strengths were obtained by increasing the amount of pyrophosphate formed in the matrix due to a post-hardening regime prior sintering as well as by the formation of a glass phase from TCP and calcium pyrophosphate above 1,280 degrees C, which resulted in a strong densification of the samples and compressive strength of >40 MPa.

  1. Calcium phosphate/porous silicon biocomposites prepared by cyclic deposition methods: spin coating vs electrochemical activation.

    Science.gov (United States)

    Hernandez-Montelongo, J; Gallach, D; Naveas, N; Torres-Costa, V; Climent-Font, A; García-Ruiz, J P; Manso-Silvan, M

    2014-01-01

    Porous silicon (PSi) provides an excellent platform for bioengineering applications due to its biocompatibility, biodegradability, and bioresorbability. However, to promote its application as bone engineering scaffold, deposition of calcium phosphate (CaP) ceramics in its hydroxyapatite (HAP) phase is in progress. In that sense, this work focuses on the synthesis of CaP/PSi composites by means of two different techniques for CaP deposition on PSi: Cyclic Spin Coating (CSC) and Cyclic Electrochemical Activation (CEA). Both techniques CSC and CEA consisted on alternate Ca and P deposition steps on PSi. Each technique produced specific morphologies and CaP phases using the same independent Ca and P stem-solutions at neutral pH and at room temperature. The brushite (BRU) phase was favored with the CSC technique and the hydroxyapatite (HAP) phase was better synthesized using the CEA technique. Analyses by elastic backscattering spectroscopy (EBS) on CaP/PSi structures synthesized by CEA supported that, by controlling the CEA parameters, an HAP coating with the required Ca/P atomic ratio of 1.67 can be promoted. Biocompatibility was evaluated by bone-derived progenitor cells, which grew onto CaP/PSi prepared by CSC technique with a long-shaped actin cytoskeleton. The density of adhered cells was higher on CaP/PSi prepared by CEA, where cells presented a normal morphological appearance and active mitosis. These results can be used for the design and optimization of CaP/PSi composites with enhanced biocompatibility for bone-tissue engineering.

  2. Calcium phosphate/porous silicon biocomposites prepared by cyclic deposition methods: Spin coating vs electrochemical activation

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez-Montelongo, J., E-mail: jacobo.hernandez@uam.es [Departamento de Física Aplicada, Universidad Autónoma de Madrid, 28049 Madrid (Spain); Gallach, D.; Naveas, N.; Torres-Costa, V. [Departamento de Física Aplicada, Universidad Autónoma de Madrid, 28049 Madrid (Spain); Climent-Font, A. [Departamento de Física Aplicada, Universidad Autónoma de Madrid, 28049 Madrid (Spain); Centro de Microanálisis de Materiales (CMAM), Universidad Autónoma de Madrid, Madrid 28049 (Spain); García-Ruiz, J.P. [Departamento de Biología Molecular, Universidad Autónoma de Madrid, Cantoblanco, Madrid 28049 (Spain); Manso-Silvan, M. [Departamento de Física Aplicada, Universidad Autónoma de Madrid, 28049 Madrid (Spain)

    2014-01-01

    Porous silicon (PSi) provides an excellent platform for bioengineering applications due to its biocompatibility, biodegradability, and bioresorbability. However, to promote its application as bone engineering scaffold, deposition of calcium phosphate (CaP) ceramics in its hydroxyapatite (HAP) phase is in progress. In that sense, this work focuses on the synthesis of CaP/PSi composites by means of two different techniques for CaP deposition on PSi: Cyclic Spin Coating (CSC) and Cyclic Electrochemical Activation (CEA). Both techniques CSC and CEA consisted on alternate Ca and P deposition steps on PSi. Each technique produced specific morphologies and CaP phases using the same independent Ca and P stem-solutions at neutral pH and at room temperature. The brushite (BRU) phase was favored with the CSC technique and the hydroxyapatite (HAP) phase was better synthesized using the CEA technique. Analyses by elastic backscattering spectroscopy (EBS) on CaP/PSi structures synthesized by CEA supported that, by controlling the CEA parameters, an HAP coating with the required Ca/P atomic ratio of 1.67 can be promoted. Biocompatibility was evaluated by bone-derived progenitor cells, which grew onto CaP/PSi prepared by CSC technique with a long-shaped actin cytoskeleton. The density of adhered cells was higher on CaP/PSi prepared by CEA, where cells presented a normal morphological appearance and active mitosis. These results can be used for the design and optimization of CaP/PSi composites with enhanced biocompatibility for bone-tissue engineering. - Highlights: • Proposed cyclic methods produce specific morphologies and CaP phases in biocomposites. • The brushite phase is favored in the biocomposite produced by Cyclic Spin Coating. • The hydroxyapatite phase is favored in the biocomposite produced by Cyclic Electrochemical Activation. • The Ca/P atomic ratio of hydroxyapatite was validated by elastic backscattering spectroscopy. • Cells grown showed morphological and

  3. Preparation, physical-chemical characterization, and cytocompatibility of polymeric calcium phosphate cements.

    Science.gov (United States)

    Khashaba, Rania M; Moussa, Mervet; Koch, Christopher; Jurgensen, Arthur R; Missimer, David M; Rutherford, Ronny L; Chutkan, Norman B; Borke, James L

    2011-01-01

    Aim. Physicochemical mechanical and in vitro biological properties of novel formulations of polymeric calcium phosphate cements (CPCs) were investigated. Methods. Monocalcium phosphate, calcium oxide, and synthetic hydroxyapatite were combined with either modified polyacrylic acid, light activated polyalkenoic acid, or polymethyl vinyl ether maleic acid to obtain Types I, II, and III CPCs. Setting time, compressive and diametral strength of CPCs was compared with zinc polycarboxylate cement (control). Specimens were characterized using X-ray diffraction, scanning electron microscopy, and infrared spectroscopy. In vitro cytotoxicity of CPCs and control was assessed. Results. X-ray diffraction analysis showed hydroxyapatite, monetite, and brushite. Acid-base reaction was confirmed by the appearance of stretching peaks in IR spectra of set cements. SEM revealed rod-like crystals and platy crystals. Setting time of cements was 5-12 min. Type III showed significantly higher strength values compared to control. Type III yielded high biocompatibility. Conclusions. Type III CPCs show promise for dental applications.

  4. Porous bioceramic bead prepared by calcium phosphate with sodium alginate gel and PE powder

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Y.C. [Department of Orthopaedic Surgery, Kaohsiung Medical University Hospital, Kaohsiung 807, Taiwan (China); Ho, M.L.; Wu, S.C. [Department of Physiology, Kaohsiung Medical University, 100, Shih-Chuan 1st Rd, Kaohsiung 807, Taiwan (China); Hsieh, H.S. [Faculty of Medicinal and Applied Chemistry, Kaohsiung Medical University, 100, Shih-Chuan 1st Rd, Kaohsiung 807, Taiwan (China); Wang, C.K. [Faculty of Medicinal and Applied Chemistry, Kaohsiung Medical University, 100, Shih-Chuan 1st Rd, Kaohsiung 807, Taiwan (China)], E-mail: ckwang@kmu.edu.tw

    2008-08-01

    The porous calcium phosphate beads were made by an alginate-interacting Ca ions mechanism on addition of a pore-forming polyethylene (PE) powder at 1250 deg. C sintering. The nature of the powders and porous beads were analyzed through X-ray diffraction (XRD), Fourier transform infrared spectrometry (FTIR) and heavy metal analysis by inductively coupled plasma-optical emission spectroscopy (ICP-OES). The porous beads size and the pore microstructure characteristics were determined using scanning electron microscopy (SEM). Beside, the porosity analysis was evaluated out using an Archimedes' principle and mercury porosimetry. Then, the sodium ampicillin was penetrated/adsorbed onto calcium-deficient hydroxyapatite porous beads, and was subsequently released in PBS. No matter whether the raw material was HAp, TCP or biphase, the Ca{sub 9}(HPO{sub 4})(PO{sub 4}){sub 5}OH phase (CDHA) was formed only after sintering. Porous beads of various calcium phosphates with different sizes (0.9-1.1 mm) and pore size groups (60-120 {mu}m and lower than 10 {mu}m) were appeared. The release kinetics of sodium ampicillin from these porous beads have indicated the possibility of using these materials as possible carriers for drug delivery.

  5. Calcium Phosphate Biomaterials: An Update

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Current calcium phosphate (CaP) biomaterials for bone repair, substitution, augmentation and regeneration include hydroxyapatite ( HA ) from synthetic or biologic origin, beta-tricalcium phosphate ( β-TCP ) , biphasic calcium phosphate (BCP), and are available as granules, porous blocks, components of composites (CaP/polymer) cements, and as coatings on orthopedic and dental implants. Experimental calcium phosphate biomaterials include CO3- and F-substituted apatites, Mg-and Zn-substituted β-TCP, calcium phosphate glasses. This paper is a brief review of the different types of CaP biomaterials and their properties such as bioactivity, osteoconductivity, osteoinductivity.

  6. Preparation, Physical-Chemical Characterization, and Cytocompatibility of Polymeric Calcium Phosphate Cements

    Science.gov (United States)

    Khashaba, Rania M.; Moussa, Mervet; Koch, Christopher; Jurgensen, Arthur R.; Missimer, David M.; Rutherford, Ronny L.; Chutkan, Norman B.; Borke, James L.

    2011-01-01

    Aim. Physicochemical mechanical and in vitro biological properties of novel formulations of polymeric calcium phosphate cements (CPCs) were investigated. Methods. Monocalcium phosphate, calcium oxide, and synthetic hydroxyapatite were combined with either modified polyacrylic acid, light activated polyalkenoic acid, or polymethyl vinyl ether maleic acid to obtain Types I, II, and III CPCs. Setting time, compressive and diametral strength of CPCs was compared with zinc polycarboxylate cement (control). Specimens were characterized using X-ray diffraction, scanning electron microscopy, and infrared spectroscopy. In vitro cytotoxicity of CPCs and control was assessed. Results. X-ray diffraction analysis showed hydroxyapatite, monetite, and brushite. Acid-base reaction was confirmed by the appearance of stretching peaks in IR spectra of set cements. SEM revealed rod-like crystals and platy crystals. Setting time of cements was 5–12 min. Type III showed significantly higher strength values compared to control. Type III yielded high biocompatibility. Conclusions. Type III CPCs show promise for dental applications. PMID:21941551

  7. Preparation, Physical-Chemical Characterization, and Cytocompatibility of Polymeric Calcium Phosphate Cements

    Directory of Open Access Journals (Sweden)

    Rania M. Khashaba

    2011-01-01

    Full Text Available Aim. Physicochemical mechanical and in vitro biological properties of novel formulations of polymeric calcium phosphate cements (CPCs were investigated. Methods. Monocalcium phosphate, calcium oxide, and synthetic hydroxyapatite were combined with either modified polyacrylic acid, light activated polyalkenoic acid, or polymethyl vinyl ether maleic acid to obtain Types I, II, and III CPCs. Setting time, compressive and diametral strength of CPCs was compared with zinc polycarboxylate cement (control. Specimens were characterized using X-ray diffraction, scanning electron microscopy, and infrared spectroscopy. In vitro cytotoxicity of CPCs and control was assessed. Results. X-ray diffraction analysis showed hydroxyapatite, monetite, and brushite. Acid-base reaction was confirmed by the appearance of stretching peaks in IR spectra of set cements. SEM revealed rod-like crystals and platy crystals. Setting time of cements was 5–12 min. Type III showed significantly higher strength values compared to control. Type III yielded high biocompatibility. Conclusions. Type III CPCs show promise for dental applications.

  8. Preparation of amorphous calcium-magnesium phosphates at pH 7 and characterization by x-ray absorption and fourier transform infrared spectroscopy

    NARCIS (Netherlands)

    Holt, C.; Kemenade, M.J.J.M. van; Harries, J.E.; Nelson, L.S.; Bailey, R.T.; Hukins, D.W.L.; Hasnain, S.S.; Bruyn, P.L. de

    1988-01-01

    Amorphous calcium-magnesium phosphates were prepared by precipitation from moderately supersaturated aqueous solutions at pH 7. Chemical analysis of the samples by ion chromatography showed that up to about 50% of the phosphate ions were protonated, the proportion increasing with the magnesium to ca

  9. RAPID ASSOCIATION OF UNCONJUGATED BILIRUBIN WITH AMORPHOUS CALCIUM-PHOSPHATE

    NARCIS (Netherlands)

    VANDERVEERE, CN; SHOEMAKER, B; VANDERMEER, R; GROEN, AK; JANSEN, PLM; ELFERINK, RPJO

    1995-01-01

    The association of unconjugated bilirubin (UCB) with amorphous calcium phosphate was studied in vitro. To this end UCB, solubilized in different micellar bile salt solutions, was incubated with freshly prepared calcium phosphate precipitate. It was demonstrated that amorphous calcium phosphate (ACP)

  10. Amorphous calcium phosphate nanospheres/polylactide composite coated tantalum scaffold: facile preparation, fast biomineralization and subchondral bone defect repair application.

    Science.gov (United States)

    Zhou, Rong; Xu, Wei; Chen, Feng; Qi, Chao; Lu, Bing-Qiang; Zhang, Hao; Wu, Jin; Qian, Qi-Rong; Zhu, Ying-Jie

    2014-11-01

    Calcium phosphate (CaP) materials are widely used in various biomedical areas such as drug/gene delivery and bone repair/tissue engineering. In this study, amorphous CaP nanospheres synthesized by a simple co-precipitation method are used to prepare the CaP-polylactide (CaP-PLA) composite. Then, the as-prepared CaP-PLA composite is used to coat tantalum (Ta) plates and porous scaffolds. Compared with bare Ta plate, CaP-PLA coated Ta plates show a high performance of surface biomineralization in simulated body fluid (SBF). In addition, the hydrophilicity of the CaP-PLA coated Ta plates is significantly improved. CaP-PLA coated Ta plates with bovine serum albumin (BSA) are prepared and used for the investigation of BSA release in vitro. The experimental results indicate a sustained BSA release property and simultaneous biomineralization of the as-prepared BSA-containing CaP-PLA coated Ta plates. Furthermore, CaP-PLA coated Ta scaffolds are favorable for the human osteoblast-like MG63 cells adhesion and spreading. The vascular endothelial growth factor (VEGF) and transforming growth factor (TGF)-containing CaP-PLA coated porous Ta scaffolds are used for the study of rabbit subchondral bone defect repair, covering with autogeneic periosteums. The as-prepared CaP-PLA composite coated Ta scaffolds are useful to guide the bone regeneration in vivo. Copyright © 2014 Elsevier B.V. All rights reserved.

  11. Calcium phosphates for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Canillas, M.; Pena, P.; Aza, A.H. de; Rodriguez, M.A.

    2017-07-01

    The history of calcium phosphates in the medicine field starts in 1769 when the first evidence of its existence in the bone tissue is discovered. Since then, the interest for calcium phosphates has increased among the scientific community. Their study has been developed in parallel with new advances in materials sciences, medicine or tissue engineering areas. Bone tissue engineering is the field where calcium phosphates have had a great importance. While the first bioceramics are selected according to bioinert, biocompatibility and mechanical properties with the aim to replace bone tissue damaged, calcium phosphates open the way to the bone tissue regeneration challenge. Nowadays, they are present in the majority of commercial products directed to repair or regenerate damaged bone tissue. Finally, in the last few decades, they have been suggested and studied as drug delivering devices and as vehicles of DNA and RNA for the future generation therapies. (Author)

  12. Preparation of a Novel Calcium Phosphate Cement Using N-methylene Phosphonic Chitosan as a Gelling Agent

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    A modified chitosan ( N-methylene phosphonic Chitosan, NMPC ) was synthesized to improve solubility and ability to bind calcium ion. The properties of the raw material chitosan and its derivative NMPC were characterized using FTIR, 1 H-NMR. The aim of this study was to enhance the compressive CPC by reinforcing with NMPC. A formulation consisting of CPC powder, buffer solution and gelling agent was used for preparation of the CPC. CPC powder consisted of tetracalcium phosphate (TTCP) and dicalcium phosphate anhydrous ( DCPA ). NMPC which acted as the gelling agent was dissolved iuto KH2 PO4 -Na2 HPO4 buffer solution. Each specimen in the mold was sandwiched between two fritted glass sides and kept for 24 hours. Compressive strengths were determined, the setting product was identified using X-ray diffraction and scanning electron microscopy was used to investigate the hydroxyapatite particles size and porosity. The experimental results showed that the dominating influence on the compressive strengths of CPC-NMPC was the HA particle size, its uniformity and appropriate porosity.

  13. Control of crystallinity and composition in calcium phosphate coatings

    Energy Technology Data Exchange (ETDEWEB)

    Cifuentes, M.; Cabanas, M.V.; Vallet-Regi, M. [Universidad Complutense de Madrid (Spain). Dept. de Quimica Inorganica y Bioinorganica

    2001-07-01

    Calcium phosphate coatings were prepared by the so-called pyrosol method. Both crystallinity and composition of obtained films can be controlled by modifying the composition of the precursor solution, surrounding atmosphere and substrate temperature. In this way, tricalcium phosphate, hydroxyapatite or biphasic hydroxyapatite/tricalcium phosphate with different crystallinity and microstructure have been prepared. (orig.)

  14. Calcium phosphate composite materials including inorganic powders, BSA or duplex DNA prepared by W/O/W interfacial reaction method

    Energy Technology Data Exchange (ETDEWEB)

    Fujiwara, Masahiro [National Institute of Advanced Industrial Science and Technology (AIST), Kansai Center, 1-8-31 Midorigaoka, Ikeda, Osaka 563-8577 (Japan)], E-mail: m-fujiwara@aist.go.jp; Shiokawa, Kumi; Morigaki, Kenichi; Tatsu, Yoshiro; Nakahara, Yoshiko [National Institute of Advanced Industrial Science and Technology (AIST), Kansai Center, 1-8-31 Midorigaoka, Ikeda, Osaka 563-8577 (Japan)

    2008-03-10

    We reported before that inorganic reaction occurring at the interface of W/O/W emulsion is advantageous to produce hollow spheres (microcapsules) of inorganic matrices such as silica. This process enables us to include various materials into inorganic matrices directly. Calcium phosphates were also produced from NH{sub 4}H{sub 2}PO{sub 4} and Ca(OH){sub 2} by this interfacial reaction method. Various biomaterials are directly incorporated into crystalline calcium phosphate matrices, when the biomaterials are added to the inner water phase of the W/O/W emulsion. ZrO{sub 2} and Al{sub 2}O{sub 3} powders were effectively encapsulated in calcium phosphates such as hydroxyapatite (HAp). The images of backscattered electron of FE-SEM observations indicated that ZrO{sub 2} particles were included in HAp, while they adhered to the surface of HAp in the case of a simple precipitation method. Biomacromolecules such as BSA and duplex DNA were also included in HAp using the inner water phases dissolving them. Fluorescent microscopy observations revealed that biomacromolecules incorporated in HAp localized in some domains of the HAp matrices. Biomacromolecules thus included were scarcely liberated into deionized water, indicating their strong encapsulation in HAp. This general and simple methodology will provide various composite materials of calcium phosphates, which are applicable to regenerative medicine, DDS, GDS and more.

  15. Influence of precursor solution parameters on chemical properties of calcium phosphate coatings prepared using Electrostatic Spray Deposition (ESD).

    NARCIS (Netherlands)

    Leeuwenburgh, S.C.G.; Wolke, J.G.C.; Schoonman, J.; Jansen, J.A.

    2004-01-01

    A novel coating technique, referred to as Electrostatic Spray Deposition (ESD), was used to deposit calcium phosphate (CaP) coatings with a variety of chemical properties. The relationship between the composition of the precursor solutions and the crystal and molecular structure of the deposited coa

  16. Preparation and characterization of calcium phosphate ceramics and Composites as bone substitutes

    OpenAIRE

    Zhang, Xing

    2007-01-01

    Marine CaCO₃ skeletons have tailored architectures created by nature, which give them structural support and other functions. For example, seashells have dense lamellar structures, while coral, cuttlebone and sea urchin spines have interconnected porous structures. In our experiments, seashells, coral and cuttlebone were hydrothermally converted to hydroxyapatite (HAP), and sea urchin spines were converted to Mg-substituted tricalcium phosphate [beta]-TCMP, while maintaining their original st...

  17. Nanocrystalline biphasic resorbable calcium phosphate (HAp/β-TCP) thin film prepared by electron beam evaporation technique

    Energy Technology Data Exchange (ETDEWEB)

    Elayaraja, K.; Chandra, V. Sarath; Joshy, M.I. Ahymah; Suganthi, R.V. [Crystal Growth Centre, Anna University, Chennai 600025, Tamil Nadu (India); Asokan, K. [Inter-University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Kalkura, S. Narayana, E-mail: kalkura@yahoo.com [Crystal Growth Centre, Anna University, Chennai 600025, Tamil Nadu (India)

    2013-06-01

    Biphasic calcium phosphate (BCP) thin film having resorbable β-tricalcium phosphate (β-TCP) and non-resorbable hydroxyapatite (HAp) phases having enhanced bioactivity was synthesized by electron beam evaporation technique. Nanosized BCP was deposited as a layer (500 nm) on (0 0 1) silicon substrate by electron beam evaporation and crystalline phase of samples were found to improve on annealing at 700 °C. Uniform deposition of calcium phosphate on silicon substrate was verified from elemental mapping using scanning electron microscope (SEM-EDX). Annealing of the samples led to a decrease in surface roughness, hydrophobicity and dissolution of the coating layer. Amoxicillin loaded thin films exhibited significant bacterial resistance. In addition, BCP thin films did not exhibit any cytotoxicity. Antibiotics incorporated BCP coated implants might prevent the post-surgical infections and could promote bone-bonding of orthopedic devices.

  18. The preparation and properties of degradable calcium phosphate bioceramics%可降解磷酸钙生物陶瓷的制备与性能∗

    Institute of Scientific and Technical Information of China (English)

    李漱阳; 李鸿; 王鹏; 刘鹏真; 严永刚

    2015-01-01

    通过用磷酸二氢钙与碳酸钙粉体、磷酸氢钙与硫酸钙粉体进行混合烧结制方法制备了一系列磷酸钙生物陶瓷材料,并通过 XRD、FI-IR、降解试验、钙磷比分析、SEM 观察和细胞毒性实验对改性磷酸钙陶瓷进行了表征.结果表明,在750℃烧结下,磷酸二氢钙与碳酸钙摩尔比为1∶1时生成磷酸三钙,其摩尔比为1∶2与1∶2.3时生成磷酸三钙、羟基磷灰石双相生物陶瓷;磷酸氢钙与硫酸钙摩尔比为1∶0.67与1∶0.5,经烧结后生成焦磷酸钙与硫酸钙双相生物陶瓷.降解试验表明焦磷酸钙与硫酸钙双相生物陶瓷在 PBS 中浸泡28 d 后,其失重率分别为35%和36%,且对浸泡液 pH 值无显著影响;而得到磷酸三钙陶瓷和磷酸三钙、羟基磷灰石复相陶瓷降解较小,且对 pH 值有明显影响.细胞毒性实验表明,焦磷酸钙与硫酸钙双相生物陶瓷无细胞毒性.%Using sintering methods on the mixture of the calcium dihydrogen phosphate and calcium carbonate powder,and the calcium hydrogen phosphate and calcium sulfate powder,a series of calcium phosphate bioce-ramics materials were prepared.The samples were detected by XRD,FI-IR,degradation experiments,calcium and phosphorus ratio analysis,SEM observation and cytotoxicity test.Results showed that under the 750 ℃sintering,calcium dihydrogen phosphate and calcium carbonate with 1 ∶ 1 mole ratio generated calcium phos-phate.When the molar ratios were 1∶2 and 1∶2.3,the calcium phosphate and hydroxyapatite bipolar biologi-cal ceramic was generated.Calcium hydrogen phosphate and calcium sulfate with molar ratios of 1∶0.67 and 1∶0.5 generated the calcium pyrophosphate and calcium sulfate bipolar biological ceramics.Degradation experi-ment showed that the weight loss of calcium pyrophosphate and calcium sulfate bipolar biological ceramics were 35% and 36%,respectively,after soaking in PBS for 28 days,and had no significant effect on the p

  19. 21 CFR 582.5217 - Calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium phosphate. 582.5217 Section 582.5217 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Supplements 1 § 582.5217 Calcium phosphate. (a) Product. Calcium phosphate (mono-, di-, and tribasic)....

  20. 21 CFR 582.1217 - Calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Calcium phosphate. 582.1217 Section 582.1217 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1217 Calcium phosphate. (a) Product. Calcium phosphate (mono-, di-, and tribasic)....

  1. 21 CFR 182.1217 - Calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium phosphate. 182.1217 Section 182.1217 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... Substances § 182.1217 Calcium phosphate. (a) Product. Calcium phosphate (mono-, di-, and tribasic)....

  2. Three-dimensionally Perforated Calcium Phosphate Ceramics

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Porous calcium phosphate ceramics were produced by compression molding using a special mold followed by sintering. The porous calcium phosphate ceramics have three-dimensional and penetrated open pores380-400μm in diameter spaced at intervals of 200μm. The layers of the linear penetration pores alternately lay perpendicular to pore direction. The porosity was 59%-65% . The Ca/P molar ratios of the porous calcium phosphate ceramics range from 1.5 to 1.85. A binder containing methyl cellulose was most effective for preparing the powder compact among vinyl acetate, polyvinyl alcohol, starch, stearic acid, methyl cellulose and their mixtures. Stainless steel, polystyrene, nylon and bamboo were used as the long columnar male dies for the penetrated open pores. When polystyrene, nylon and bamboo were used as the long columnar male dies, the dies were burned out during the sintering process. Using stainless steel as the male dies with the removal of the dies before heat treatment resulted in a higher level of densification of the calcium phosphate ceramic.

  3. Calcium phosphate polymer hybrid materials

    OpenAIRE

    2011-01-01

    Calcium phosphate (CaP) is of strong interest to the medical field because of its potential for bone repair, gene transfection, etc.1-3 Nowadays, the majority of the commercially available materials are fabricated via “classical” materials science approaches, i.e. via high temperature or high pressure approaches, from rather poorly defined slurries, or from organic solvents.3,4 Precipitation of inorganics with (polymeric) additives from aqueous solution on the other hand enables the synthesis...

  4. Sintering of calcium phosphate bioceramics.

    Science.gov (United States)

    Champion, E

    2013-04-01

    Calcium phosphate ceramics have become of prime importance for biological applications in the field of bone tissue engineering. This paper reviews the sintering behaviour of these bioceramics. Conventional pressureless sintering of hydroxyapatite, Ca10(PO4)6(OH)2, a reference compound, has been extensively studied. Its physico-chemistry is detailed. It can be seen as a competition between two thermally activated phenomena that proceed by solid-state diffusion of matter: densification and grain growth. Usually, the objective is to promote the first and prevent the second. Literature data are analysed from sintering maps (i.e. grain growth vs. densification). Sintering trajectories of hydroxyapatite produced by conventional pressureless sintering and non-conventional techniques, including two-step sintering, liquid phase sintering, hot pressing, hot isostatic pressing, ultrahigh pressure, microwave and spark plasma sintering, are presented. Whatever the sintering technique may be, grain growth occurs mainly during the last step of sintering, when the relative bulk density reaches 95% of the maximum value. Though often considered very advantageous, most assisted sintering techniques do not appear very superior to conventional pressureless sintering. Sintering of tricalcium phosphate or biphasic calcium phosphates is also discussed. The chemical composition of calcium phosphate influences the behaviour. Similarly, ionic substitutions in hydroxyapatite or in tricalcium phosphate create lattice defects that modify the sintering rate. Depending on their nature, they can either accelerate or slow down the sintering rate. The thermal stability of compounds at the sintering temperature must also be taken into account. Controlled atmospheres may be required to prevent thermal decomposition, and flash sintering techniques, which allow consolidation at low temperature, can be helpful.

  5. Preparation of Surfactant-free Core-Shell Poly(lactic acid) / Calcium Phosphate Hybrid Particles and Their Drug Release Characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Kuno, T; Hirao, K [Department of Frontier Materials, Graduate School of Engineering, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya, 466-8555 (Japan); Nagata, F; Ohji, T; Kato, K, E-mail: katsuya-kato@aist.go.jp [Advanced Manufacturing Research Institute, National Institute of Advanced Industrial Science and Technology (AIST), 2266-98, Anagahora, Shimoshidami, Moriyama-ku, Nagoya, 463-8510 (Japan)

    2011-04-15

    We propose surfactant-free core-shell poly(lactic acid) (PLA) / calcium phosphate (CaP) hybrid particles as drug delivery carriers. These particles were prepared by biomineralization process using ultrasonic irradiation, and their drug release profiles were investigated. Drug release rate was earlier when particles were prepared by PLA with a low molecular weight, and/or by Ca(CH{sub 3}COO){sub 2} and (NH{sub 4}){sub 2}HPO{sub 4}. Also, these were shown good protein adsorption. This work indicates that these particles have sustained-release ability without initial burst and can do targeting capability by biomolecule conjugation.

  6. Preparation of Bioactive Calcium Phosphate Coating on Porous C/C Substrate by a Novel Deposition Technique

    Institute of Scientific and Technical Information of China (English)

    XIONG Xinbo; ZENG Xierong; LI Xiaohua; Xie Shenghui; ZOU Chunli

    2008-01-01

    A novel heat substrate technique,high frequency inductive heat deposition(IHD),was introduced to coat porous carbon materials,C/C and carbon felt to improve their bioactivity.The morphologies,composition and microstructure of the resulting coatings were examined by scanning electron microscopy(SEM),energy dispersive spectra(EDS),X-ray diffractometer(XRD)and Fourier transform infrared spectroscopy (FTIR).The results show that,the calcium phosphate consisted of non-stoichiometric,CO3-containing and plate-like octacalcium phosphate(Ca8-xH2(PO4)6,OCP)could uniformly cover the entire porous surfaces of carbon materials.Good adhesion of the coating to carbon material substrates was observed.

  7. Injectable bioactive calcium-magnesium phosphate cement for bone regeneration.

    Science.gov (United States)

    Wu, Fan; Su, Jiacan; Wei, Jie; Guo, Han; Liu, Changsheng

    2008-12-01

    Novel injectable and degradable calcium-magnesium phosphate cement (CMPC) with rapid-setting characteristic was developed by the introduction of magnesium phosphate cement (MPC) into calcium phosphate cement (CPC). The calcium-magnesium phosphate cement prepared under the optimum P/L ratio exhibited good injectability and desired workability. It could set within 10 min at 37 degrees C in 100% relative humidity and the compressive strength could reach 47 MPa after setting for 48 h, indicating that the prepared cement has relatively high initial mechanical strength. The results of in vitro degradation experiments demonstrated the good degradability of the injectable CMPC, and its degradation rate occurred significantly faster than that of pure CPC in simulated body fluid (SBF) solution. It can be concluded that the novel injectable calcium-magnesium phosphate cement is highly promising for a wide variety of clinical applications, especially for the development of minimally invasive techniques.

  8. 21 CFR 182.8217 - Calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium phosphate. 182.8217 Section 182.8217 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... phosphate. (a) Product. Calcium phosphate (mono-, di-, and tribasic). (b) Conditions of use. This...

  9. Compósitos colágeno aniônico: fosfato de cálcio. Preparação e caracterização Collagen: calcium phosphate composites. Preparation and characterization

    Directory of Open Access Journals (Sweden)

    Marcos Roberto Bet

    1997-10-01

    Full Text Available Anionic collagen: calcium phosphate composite was obtained by controlled mixing of collagen and calcium phosphate until the consistence of a past. Material was characterized by a Ca/P ratio of 1.55, with a X-ray diffraction pattern similar to that for hydroxyapatite. Differential Scanning Calorimetry showed that the protein is not denatured under the processing conditions. Scanning Electronic Microscopy showed that the mineral phase are regularly covered with collagen fibers, indicating that anionic collagen is efficient in the preparation of stable form of calcium phosphate ceramic paste.

  10. Crystallo-chemical analyses of calcium phosphates

    Energy Technology Data Exchange (ETDEWEB)

    Sakae, Toshiro; Hayakawa, Tohru; Maruyama, Fumiaki; Nemoto, Kimiya; Kozawa, Yukishige [Nihon Univ., Matsudo, Chiba (Japan). School of Dentistry

    1997-12-01

    Several analytical techniques, methodology and their practical data processing were briefly described to investigate the crystallographic properties of calcium phosphates which are encountered in the field of dental sciences. The applied analytical techniques were X-ray fluorescence spectrometry (XFS), energy dispersive spectrometry (EDS), Fourier transform infrared spectrometry (FT-IR) and X-ray diffraction (XRD). The used materials were tetracalcium phosphate, hydroxyapatite, fluorapatite, {alpha}-tricalcium phosphate, {beta}-tricalcium phosphate, octacalcium phosphate, monetite, brushite and monocalcium phosphate monohydrate. (author)

  11. Application of Calcium Phosphate Materials in Dentistry

    Directory of Open Access Journals (Sweden)

    Jabr S. Al-Sanabani

    2013-01-01

    Full Text Available Calcium phosphate materials are similar to bone in composition and in having bioactive and osteoconductive properties. Calcium phosphate materials in different forms, as cements, composites, and coatings, are used in many medical and dental applications. This paper reviews the applications of these materials in dentistry. It presents a brief history, dental applications, and methods for improving their mechanical properties. Notable research is highlighted regarding (1 application of calcium phosphate into various fields in dentistry; (2 improving mechanical properties of calcium phosphate; (3 biomimetic process and functionally graded materials. This paper deals with most common types of the calcium phosphate materials such as hydroxyapatite and tricalcium phosphate which are currently used in dental and medical fields.

  12. Comparison and preparation of multilayered polylactic acid fabric strengthen calcium phosphate-based bone substitutes for orthopedic applications.

    Science.gov (United States)

    Chen, Wen-Cheng; Ko, Chia-Ling; Yang, Jia-Kai; Wu, Hui-Yu; Lin, Jia-Horng

    2016-03-01

    An attempt to maintain the three-dimensional space into restorative sites through the conveniently pack porous fillers are general used strategy. Advancement in the manufacturing protective shells in the scaffolds, which would be filled with brittle ceramic grafts for the development of highly connective pores provides the approach to solve crack problem for generating the tissues. Therefore, multilayered braided and alkalized poly(lactic acid) (PLA) composites with calcium phosphate bone cement (CPC) were synthesized and compared. The PLA/CPC composites were divided into various groups according to a series of heat-treatment temperatures (100-190 °C) and periods (1-3 h) and then characterized. The effects of 24-h immersion on the strength decay resistance of the samples were compared. Results showed that the residual oil capped on the surfaces of alkalized PLA braid was removed, and the structure was unaltered. However, the reduced tensile stress of alkalized PLA braids was due to ester-group formation by hydrolysis. Mechanical test results of PLA/CPC composites showed that the strength significantly increased after heat treatment, except when the heating temperature was higher than the PLA melting point at approximately 160-170 °C. The degree of PLA after recrystallization became higher than that of unheated composites, thereby leading to reduced strength and toughness of the specimen. Braiding fibers of biodegradable PLA reinforced and toughened the structure particularly of the extra-brittle material of thin-sheet CPC after implantation.

  13. 硝酸浸取磷矿制轻质碳酸钙工艺研究%Preparation of light calcium carbonate by nitric acid leaching phosphate ore

    Institute of Scientific and Technical Information of China (English)

    胡兆平; 贾洪秀; 庞世花; 刘阳; 贾亮

    2013-01-01

    Calcium nitrate crystal can be obtained by freezing crystallization method from acid solution acquired from nitric acid extracting phosphate rock.After that,light calcium carbonate was prepared by carbonization reaction between ammonium hydrogen carbonate and calcium nitrate crystal.Results show that,the initial carbonization reaction temperature was the normal temperature,mass fraction of calcium nitrate solution was about 23%,ammonium hydrogen carbonate and ammonia dosages were both 110% of theoretical addition amounts,and products were washed by four times of product weight washing water.All quality indexes of the product can meet the standard of Industrial Precipitated Calcium Carbonate,HG/T 2226-2000.%硝酸萃取磷矿后的酸解液,通过冷冻结晶法得到硝酸钙晶体,然后以硝酸钙为原料,通过加入碳酸氢铵进行碳化制取轻质碳酸钙.结果表明,碳化反应的初始反应温度为常温,硝酸钙溶液的质量分数为23%左右,碳酸氢铵和氨水按理论加入量的110%进行反应,用产品质量的4倍洗水量洗涤产品,制备的轻质碳酸钙产品各项指标均达到HG/T 2226-2000《工业沉淀碳酸钙》标准的要求.

  14. Preparation and In Vitro and In Vivo Performance of Magnesium Ion Substituted Biphasic Calcium Phosphate Spherical Microscaffolds as Human Adipose Tissue-Derived Mesenchymal Stem Cell Microcarriers

    Directory of Open Access Journals (Sweden)

    Dong-Hyun Kim

    2013-01-01

    Full Text Available Magnesium ion substituted biphasic calcium phosphate (Mg-BCP bioceramic microscaffolds with spherical and porous morphology were successfully prepared using in situ coprecipitation and rotary spray drying atomization process for application of tissue engineering combined with human adipose tissue-derived mesenchymal stem cells (hAT-MSCs. After 4 weeks of immersion in Hanks’ balanced salt solution (HBSS, Mg-BCP micro-scaffolds showed the enhanced biodegradation and bioactivity due to the substituted Mg2+ ion present in the BCP structure. In this study, it was observed that hAT-MSCs have clearly attached on the surface of Mg-BCP micro-scaffolds. In addition, Mg-BCP micro-scaffolds exhibited the improved biocompatibility and osteoconductivity via in vitro and in vivo biological tests with hAT-MSCs. Therefore, these bioceramic micro-scaffolds had potential to be used as hAT-MSCs microcarriers for biomedical applications.

  15. Apatite Formation from Amorphous Calcium Phosphate and Mixed Amorphous Calcium Phosphate/Amorphous Calcium Carbonate.

    Science.gov (United States)

    Ibsen, Casper J S; Chernyshov, Dmitry; Birkedal, Henrik

    2016-08-22

    Crystallization from amorphous phases is an emerging pathway for making advanced materials. Biology has made use of amorphous precursor phases for eons and used them to produce structures with remarkable properties. Herein, we show how the design of the amorphous phase greatly influences the nanocrystals formed therefrom. We investigate the transformation of mixed amorphous calcium phosphate/amorphous calcium carbonate phases into bone-like nanocrystalline apatite using in situ synchrotron X-ray diffraction and IR spectroscopy. The speciation of phosphate was controlled by pH to favor HPO4 (2-) . In a carbonate free system, the reaction produces anisotropic apatite crystallites with large aspect ratios. The first formed crystallites are highly calcium deficient and hydrogen phosphate rich, consistent with thin octacalcium phosphate (OCP)-like needles. During growth, the crystallites become increasingly stoichiometric, which indicates that the crystallites grow through addition of near-stoichiometric apatite to the OCP-like initial crystals through a process that involves either crystallite fusion/aggregation or Ostwald ripening. The mixed amorphous phases were found to be more stable against phase transformations, hence, the crystallization was inhibited. The resulting crystallites were smaller and less anisotropic. This is rationalized by the idea that a local phosphate-depletion zone formed around the growing crystal until it was surrounded by amorphous calcium carbonate, which stopped the crystallization.

  16. Physical Properties of Acidic Calcium Phosphate Cements

    OpenAIRE

    2014-01-01

    The gold standard for bone replacement today, autologous bone, suffers from several disadvantages, such as the increased risk of infection due to the need for two surgeries. Degradable synthetic materials with properties similar to bone, such as calcium phosphate cements, are a promising alternative. Calcium phosphate cements are suited for a limited amount of applications and improving their physical properties could extend their use into areas previously not considered possible. For example...

  17. lectrolytic deposition of lithium into calcium phosphate coatings

    NARCIS (Netherlands)

    Wang, Jiawei; Groot, de Klaas; Blitterswijk, van Clemens; Boer, de Jan

    2009-01-01

    Objectives: Lithium ions stimulate the Wnt signaling pathway and the authors previously demonstrated that lithium enhances the proliferation of tissue cultured human mesenchymal stem cells. The aim of this study was to prepare and characterize a calcium phosphate/lithium coating by means of electrol

  18. Hydrolytic conversion of amorphous calcium phosphate into apatite accompanied by sustained calcium and orthophosphate ions release.

    Science.gov (United States)

    Niu, Xufeng; Chen, Siqian; Tian, Feng; Wang, Lizhen; Feng, Qingling; Fan, Yubo

    2017-01-01

    The aim of this study is to investigate the calcium and orthophosphate ions release during the transformation of amorphous calcium phosphate (ACP) to hydroxyapatite (HA) in aqueous solution. The ACP is prepared by a wet chemical method and further immersed in the distilled water for various time points till 14d. The release of calcium and orthophosphate ions is measured with calcium and phosphate colorimetric assay kits, respectively. The transition of ACP towards HA is detected by x-ray diffraction (XRD), transmission electron microscopy (TEM), and fourier transform infrared spectroscopy (FTIR). The results indicate that the morphological conversion of ACP to HA occurs within the first 9h, whereas the calcium and orthophosphate ions releases last for over 7d. Such sustained calcium and orthophosphate ions release is very useful for ACP as a candidate material for hard tissue regeneration.

  19. Formation of calcium phosphate mineral materialcontrolled by microemulsion

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In order to prepare calcium phosphate-based material with nano-structure and bioactivity, natural lecithin and n-tetradecane were used as the amphipile and the oil phase respectively, along with the water phase, to form a microemulsion template. Phosphate mineralization was induced and controlled by the microemulsion. The products, characterized by scanning electronic microscopy, infrared spectroscopy and X-ray diffraction analysis, are composed of lecithin and hydroxyapatite, and possess the nano-structure of sticks, balls and three-dimensional nets connected by tubes. These results show that the microemulsion can be used to control calcium phosphate mineralization for the preparation of biomimetic mineral materials with various nano-structures.

  20. The in vitro behavior of as-prepared and pre-immersed RF-sputtered calcium phosphate thin films in a rat bone marrow cell model.

    NARCIS (Netherlands)

    Wal, E. van de; Vredenberg, A.M.; Brugge, P.J. ter; Wolke, J.G.C.; Jansen, J.A.

    2006-01-01

    In this paper we focus on the behavior of radio frequency (RF)-sputtered calcium phosphate (CaP) thin films in a rat bone marrow (RBM) cell model. Two issues are addressed. Firstly, we benchmarked the in vitro cell behavior of these CaP coatings by comparing their proliferation, differentiation and

  1. Calcium phosphate saturation in seawater around the Andaman Island

    Digital Repository Service at National Institute of Oceanography (India)

    Naik, S.; Reddy, C.V.G.

    Ionic product (IP) of calcium phosphate is calculated at some stations around Andaman Island. The depthwise variations of the ionic product of calcium phosphate seem to follow a normal trend with maximum saturation value between 100 to 200 m. Using...

  2. Electrosprayed calcium phosphate coatings for biomedical purposes

    NARCIS (Netherlands)

    Leeuwenburgh, Sander Cornelis Gerardus

    2006-01-01

    In this thesis, the suitability of the Electrostatic Spray Deposition (ESD) technique was studied for biomedical purposes, i.e., deposition of calcium phosphate (CaP) coatings onto titanium substrates. Using ESD, which is a simple and cheap deposition method for inorganic and organic coatings, it wa

  3. Histological evaluation of degradable guided bone regeneration membranes prepared from poly(trimethylene carbonate) and biphasic calcium phosphate composites

    NARCIS (Netherlands)

    Zeng, Ni; Leeuwen, van Anne; Bos, Ruud R.M.; Grijpma, Dirk W.; Kuijer, Roel

    2013-01-01

    In oral and maxillofacial surgery, guided bone regeneration using barrier membranes is an important strategy to treat bone defects. The currently used barrier membranes have important disadvantages. Barrier membranes prepared from resorbable poly(trimethylene carbonate) (PTMC) performed as well as c

  4. Histological Evaluation of Degradable Guided Bone Regeneration Membranes Prepared from Poly(trimethylene carbonate) and Biphasic Calcium Phosphate Composites

    NARCIS (Netherlands)

    Zeng, Ni; van Leeuwen, Anne; Bos, Ruud R.M.; Grijpma, Dirk W.; Kuijer, Roel

    2013-01-01

    In oral and maxillofacial surgery, guided bone regeneration using barrier membranes is an important strategy to treat bone defects. The currently used barrier membranes have important disadvantages. Barrier membranes prepared from resorbable poly(trimethylene carbonate) (PTMC) performed as well as c

  5. Osteoclastic resorption of biomimetic calcium phosphate coatings in vitro.

    NARCIS (Netherlands)

    Leeuwenburgh, S.C.G.; Layrolle, P.; Barrere, F.; Bruijn, J.G.M. de; Schoonman, J.; Blitterswijk, C.A. van; Groot, K. de

    2001-01-01

    A new biomimetic method for coating metal implants enables the fast formation of dense and homogeneous calcium phosphate coatings. Titanium alloy (Ti6Al4V) disks were coated with a thin, carbonated, amorphous calcium phosphate (ACP) by immersion in a saturated solution of calcium, phosphate, magnesi

  6. 21 CFR 582.6215 - Monobasic calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Monobasic calcium phosphate. 582.6215 Section 582.6215 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....6215 Monobasic calcium phosphate. (a) Product. Monobasic calcium phosphate. (b) Conditions of use....

  7. 21 CFR 182.6215 - Monobasic calcium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Monobasic calcium phosphate. 182.6215 Section 182.6215 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED....6215 Monobasic calcium phosphate. (a) Product. Monobasic calcium phosphate. (b) Conditions of use....

  8. Preparation and Properties of Biphasic Calcium Phosphate Scaffolds Multiply Coated with HA/PLLA Nanocomposites for Bone Tissue Engineering Applications

    Directory of Open Access Journals (Sweden)

    Lei Nie

    2012-01-01

    Full Text Available A well-developed BCP scaffolds coated with multilayer of HA/PLLA nanocomposites with interconnectivity, high porosity, and moderate compressive strength as well as good biocompatibility were fabricated for bone tissue engineering. After being multiply coated with HA/PLLA nanocomposites, the scaffolds maintained the BCP framework structure, and the porous network structure of scaffolds remained unchanged; however, the compressive strength was increased with the increase of coating layer number of HA/PLLA nanocomposites. The prepared scaffolds showed lower variation of pH values in SBF solution, and an increase of coating layer number led to the decrease of the biodegradation rate at different days. Moreover, the multilayer coating scaffolds had good cytocompatibility, showing no negative effects on cells growth and proliferation. Furthermore, the bone-like apatite layer was built obviously in the interface of scaffold after 21 days after implantation in SD rat muscle. In conclusion, the BCP scaffold coated with multilayer of HA/PLLA nanocomposites could be a candidate as an excellent substitute for damaged or defect bone in bone tissue engineering.

  9. A Novel Polymer-Synthesized Ceramic Composite Based System for Bone Repair: Osteoblast Growth on Scaffolds with Varied Calcium Phosphate Content

    Science.gov (United States)

    2005-01-01

    demongtrated the synthesis of degradable scaffolds from PLAGA /calcium phosphate composite microspheres in which an amorphous calcium phosphate is...EXPERIMENTAL DETAILS Scaffold Preparation Scaffolds were prepared as described in detail previously [3]. Briefly, PLAGA /calcium phosphate composite...culture polystyrene (TCPS) 2- pure PLAGA microspheres 64 3- composite microsphere matrices with a low polymer/ceramic ratio 4- composite microsphere

  10. Solid state NMR study calcium phosphate ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Miquel, J.L.; Facchini, L.; Legrand, A.P. (Laboratoire de Physique Quantique, Paris (France). CNRS, URA421, ESPCI); Rey, C. (CNRS, Toulouse (France). ENSC. Laboratoire de Physico-chimie des Solides); Lemaitre, J. (EPF Lausanne (France). Laboratoire de Technologie des Poudres)

    1990-04-01

    High-resolution {sup 31}P and {sup 1}H NMR spectra at 40 and 121 MHz {sup 31}P and 300 MHz {sup 1}H of synthetic and biological samples of calcium phosphates have been obtained by magic angle spinning (MAS) at spinning speeds up to 6.5 kHz, and high power proton decoupling. The samples include crystalline hydroxyapatite, a deficient hydroxyapatite characterized by a Ca/P atomic ratio of 1.5, a poorly crystallized hydroxyapatite, monetite, brushite, octacalcium phosphate, {beta}-tricalcium phosphate and rabbit femoral bone. The interactions between nuclei in unlike structures and the mobility of acid protons are discussed. (author). 11 refs.; 2 figs.; 1 tab.

  11. Physicochemical and Microstructural Characterization of Injectable Load-Bearing Calcium Phosphate Scaffold

    OpenAIRE

    Mazen Alshaaer; Kailani, Mohammed H.; Hanan Jafar; Nidaa Ababneh; Abdalla Awidi

    2013-01-01

    Injectable load-bearing calcium phosphate scaffolds are synthesized using rod-like mannitol grains as porogen. These degradable injectable strong porous scaffolds, prepared by calcium phosphate cement, could represent a valid solution to achieve adequate porosity requirements while providing adequate support in load-bearing applications. The proposed process for preparing porous injectable scaffolds is as quick and versatile as conventional technologies. Using this method, porous CDHA-based c...

  12. The influence of Sr content in calcium phosphate coatings

    Energy Technology Data Exchange (ETDEWEB)

    Lindahl, Carl [Department of Biomaterials, Institute for Clinical Sciences, Sahlgrenska Academy at the University of Gothenburg, Gothenburg (Sweden); BIOMATCELL, VINN Excellence Center of Biomaterials and Cell Therapy, Gothenburg (Sweden); Pujari-Palmer, Shiuli; Hoess, Andreas; Ott, Marjam [Applied Materials Science, Department of Engineering Sciences, Uppsala University, Uppsala (Sweden); Engqvist, Håkan [BIOMATCELL, VINN Excellence Center of Biomaterials and Cell Therapy, Gothenburg (Sweden); Applied Materials Science, Department of Engineering Sciences, Uppsala University, Uppsala (Sweden); Xia, Wei, E-mail: wei.xia@angstrom.uu.se [BIOMATCELL, VINN Excellence Center of Biomaterials and Cell Therapy, Gothenburg (Sweden); Applied Materials Science, Department of Engineering Sciences, Uppsala University, Uppsala (Sweden)

    2015-08-01

    In this study calcium phosphate coatings with different amounts of strontium (Sr) were prepared using a biomineralization method. The incorporation of Sr changed the composition and morphology of coatings from plate-like to sphere-like morphology. Dissolution testing indicated that the solubility of the coatings increased with increased Sr concentration. Evaluation of extracts (with Sr concentrations ranging from 0 to 2.37 μg/mL) from the HA, 0.06Sr, 0.6Sr, and 1.2Sr coatings during in vitro cell cultures showed that Sr incorporation into coatings significantly enhanced the ALP activity in comparison to cells treated with control and HA eluted media. These findings show that calcium phosphate coatings could promote osteogenic differentiation even in a low amount of strontium. - Highlights: • Calcium phosphate coating doping with low Sr contents was prepared via a biomineralization process. • The solubility of the coatings increased with increased Sr concentration. • Present findings show the potential that Sr has on promoting osteogenic differentiation even in a low amount.

  13. Molecular mechanisms of crystallization impacting calcium phosphate cements

    OpenAIRE

    2010-01-01

    The biomineral calcium hydrogen phosphate dihydrate (CaHPO4·2H2O), known as brushite, is a malleable material that both grows and dissolves faster than most other calcium minerals, including other calcium phosphate phases, calcium carbonates and calcium oxalates. Within the body, this ready formation and dissolution can play a role in certain diseases, such as kidney stone and plaque formation. However, these same properties, along with brushite’s excellent biocompatibility, can be used to gr...

  14. Frozen delivery of brushite calcium phosphate cements.

    Science.gov (United States)

    Grover, Liam M; Hofmann, Michael P; Gbureck, Uwe; Kumarasami, Balamurgan; Barralet, Jake E

    2008-11-01

    Calcium phosphate cements typically harden following the combination of a calcium phosphate powder component with an aqueous solution to form a matrix consisting of hydroxyapatite or brushite. The mixing process can be very important to the mechanical properties exhibited by cement materials and consequently when used clinically, since they are usually hand-mixed their mechanical properties are prone to operator-induced variability. It is possible to reduce this variability by pre-mixing the cement, e.g. by replacing the aqueous liquid component with non-reactive glycerol. Here, for the first time, we report the formation of three different pre-mixed brushite cement formulations formed by freezing the cement pastes following combination of the powder and liquid components. When frozen and stored at -80 degrees C or less, significant degradation in compression strength did not occur for the duration of the study (28 days). Interestingly, in the case of the brushite cement formed from the combination of beta-tricalcium phosphate with 2 M orthophosphoric acid solution, freezing the cement paste had the effect of increasing mean compressive strength fivefold (from 4 to 20 MPa). The increase in compression strength was accompanied by a reduction in the setting rate of the cement. As no differences in porosity or degree of reaction were observed, strength improvement was attributed to a modification of crystal morphology and a reduction in damage caused to the cement matrix during manipulation.

  15. Mechanism of calcium phosphates precipitation in liquid crystals; Mecanisme de precipitation de phosphates de calcium dans des cristaux liquides

    Energy Technology Data Exchange (ETDEWEB)

    Prelot, B.; Zemb, T

    2004-04-01

    The possibility of using as a precursor an easily wet meso-porous powder would be a breakthrough in the preparation of nuclear waste storage ceramics. A concentrated solution containing ions to be stored would wet a dry powder and then, subjected to mild compression, lead to a micro-crystalline matrix of calcium phosphate at acceptable temperatures. Since no porous calcium phosphate different from calcined bone (patented) is described as porous precursor, we have compared the different synthesis routes towards meso-porous ceramics. First, we considered homogeneous precipitation of slats in water: using initially off-stoichiometry in reaction, micron-sized hydroxyapatite particles are produced with a specific surface up to 100 m{sup 2}/g. Then, we consider the classical route of precipitation of an hybrid material in the miscibility gap of a phase diagram, when an hexagonal liquid crystal is used a matrix for precipitation. The surfactant family consists in single chain surfactants containing phosphates as head-group to poison the growing surface of calcium phosphate nano-domains. Since the reaction is still too brutal, we considered using a cat-anionic precursor material of controllable surface charge. For certain concentrations and molar ratios, a new structure not yet described in surfactant precipitation literature is observed: since the periodicity is lower than twice the chain length, a disordered constant curvature monolayer (instead of the classical cylinder of twice chain length diameter) of surfactant is implied. Finally, we have investigated synthesis routes implying slow dissolution of pre-formed calcium phosphate in an already existing hexagonal matrix. For all these routes of synthesis, micro-structural determinations using SAXS, WARS and BET are performed, with a special attention to comparison of the precipitation material, the matrix obtained with all elements present, and also the material obtained after calcinations. (authors)

  16. Phase Composition Control of Calcium Phosphate Nanoparticles for Tunable Drug Delivery Kinetics and Treatment of Osteomyelitis. Part 1: Preparation and Drug Release

    Science.gov (United States)

    Uskoković, Vuk; Desai, Tejal A.

    2012-01-01

    Developed in this study is a multifunctional material for simultaneous osseoinduction and drug delivery, potentially applicable in the treatment of osteomyelitis. It is composed of agglomerates of nanoparticles of calcium phosphate (CAP) with different monophasic contents. The drug loading capacity and the release kinetics were investigated on two model drug compounds with different chemical structures, sizes and adsorption propensities: bovine serum albumin and fluorescein. Loading of CAP powders with small molecule drugs was achieved by physisorption and desiccation-induced agglomeration of nanoparticulate subunits into microscopic blocks. The material dissolution rate and the drug release rate depended on the nature of the CAP phase, decreasing from monocalcium phosphate to monetite to amorphous CAP and calcium pyrophosphate to hydroxyapatite. The sustained release of the two model drugs was shown to be directly relatable to the degradation rate of CAP carriers. It was demonstrated that the degradation rate of the carrier and the drug release kinetics could be made tunable within the time scale of 1–2 h for the most soluble CAP phase, monocalcium phosphate, to 1–2 years for the least soluble one, hydroxyapatite. From the standpoint of antibiotic therapy for osteomyelitis, typically lasting for six weeks, the most prospective CAP powder was amorphous CAP with its release time scale for a small organic molecule, the same category to which antibiotics belong, of 1 – 2 months under the conditions applied in our experiments. By combining these different CAP phases in various proportions, drug release profiles could be tailored to the therapeutic occasion. PMID:23115118

  17. Thermal stability of hydroxyapatite in biphasic calcium phosphate ceramics

    CSIR Research Space (South Africa)

    Nilen, RWN

    2008-04-01

    Full Text Available Biphasic calcium phosphate ceramics (BCP) comprising a mix of non-resorbable hydroxyapatite (HA) and resorbable b-tricalcium phosphate (b-TCP) are particularly suitable materials for synthetic bone substitute applications. In this study, HA...

  18. Calcium phosphate saturation in the western Bay of Bengal

    Digital Repository Service at National Institute of Oceanography (India)

    Naik, S.; Reddy, C.V.G.

    Temperature, inorganic phosphate concentration and pH seem to be the major factors influencing the degree of saturation of calcium phosphate in sea water. Two water regions can be demarcated in the study area based on the saturation patterns...

  19. Topotactic exchange and intercalation of calcium phosphate

    Science.gov (United States)

    Lima, Cicero B. A.; Airoldi, Claudio

    2004-11-01

    The precursor (NH 4) 2Ca(H 2PO 4) 2ṡH 2O (CaAP) compound was obtained by combining a calcium chloride solution with dibasic ammonium phosphate. After submitting it to a thermal treatment, crystalline calcium phosphate, Ca(H 2PO 4) 2ṡH 2O (CaP) was isolated. X-ray diffraction patterns for this compound indicated good crystallinity, with a peak at 2θ=12.8°, to give an interlamellar distance of 697 pm, which changed to 1550 pm, when the reaction employed phenylphosphonic acid, and to 1514 pm when intercalated with methylamine. Phosphorus and calcium analysis from colorimetric and gravimetric methods gave for CaP 24.2 and 15.8%, respectively, to yield a P:Ca molar ratio equal to two. The phosphorus nuclear magnetic resonance presented a peak centered at -1.23 ppm, in agreement with the existence of phosphate groups in protonated form. CaAP showed a mass loss of 21.2% in the 466 to 541 K interval due to ammonia and water elimination to yield Ca(PO 3) 3, and CaP can be dehydrated at 440 K for 6 h. A topotactical exchange occurred when CaP is intercalated with methylamine or reacted with phenylphosphonic acid to yield the phosphonate compound and the infrared spectrum of the resulting compound clearly showed the presence of PO 4 and PO 3 groups. The topotactic exchange was also demonstrated by X-ray diffractometry in following the stages of decomposition from 527 to 973 K.

  20. Hybrid calcium phosphate coatings for implants

    Science.gov (United States)

    Malchikhina, Alena I.; Shesterikov, Evgeny V.; Bolbasov, Evgeny N.; Ignatov, Viktor P.; Tverdokhlebov, Sergei I.

    2016-08-01

    Monophasic biomaterials cannot provide all the necessary functions of bones or other calcined tissues. It is necessary to create for cancer patients the multiphase materials with the structure and composition simulating the natural bone. Such materials are classified as hybrid, obtained by a combination of chemically different components. The paper presents the physical, chemical and biological studies of coatings produced by hybrid technologies (HT), which combine primer layer and calcium phosphate (CaP) coating. The first HT type combines the method of vacuum arc titanium primer layer deposition on a stainless steel substrate with the following micro-arc oxidation (MAO) in phosphoric acid solution with addition of calcium compounds to achieve high supersaturated state. MAO CaP coatings feature high porosity (2-8%, pore size 5-7 µm) and surface morphology with the thickness greater than 5 µm. The thickness of Ti primer layer is 5-40 µm. Amorphous MAO CaP coating micro-hardness was measured at maximum normal load Fmax = 300 mN. It was 3.1 ± 0.8 GPa, surface layer elasticity modulus E = 110 ± 20 GPa, roughness Ra = 0.9 ± 0.1 µm, Rz = 7.5 ± 0.2 µm, which is less than the titanium primer layer roughness. Hybrid MAO CaP coating is biocompatible, able to form calcium phosphates from supersaturated body fluid (SBF) solution and also stimulates osteoinduction processes. The second HT type includes the oxide layer formation by thermal oxidation and then CaP target radio frequency magnetron sputtering (RFMS). Oxide-RFMS CaP coating is a thin dense coating with good adhesion to the substrate material, which can be used for metal implants. The RFMS CaP coating has thickness 1.6 ± 0.1 µm and consists of main target elements calcium and phosphorus and Ca/P ratio 2.4. The second HT type can form calcium phosphates from SBF solution. In vivo study shows that hybrid RFMS CaP coating is biocompatible and produces fibrointegration processes.

  1. Fabrications of zinc-releasing biocement combining zinc calcium phosphate to calcium phosphate cement.

    Science.gov (United States)

    Horiuchi, Shinya; Hiasa, Masahiro; Yasue, Akihiro; Sekine, Kazumitsu; Hamada, Kenichi; Asaoka, Kenzo; Tanaka, Eiji

    2014-01-01

    Recently, zinc-releasing bioceramics have been the focus of much attention owing to their bone-forming ability. Thus, some types of zinc-containing calcium phosphate (e.g., zinc-doped tricalcium phosphate and zinc-substituted hydroxyapatite) are examined and their osteoblastic cell responses determined. In this investigation, we studied the effects of zinc calcium phosphate (ZCP) derived from zinc phosphate incorporated into calcium phosphate cement (CPC) in terms of its setting reaction and MC3T3-E1 osteoblast-like cell responses. Compositional analysis by powder X-ray diffraction analysis revealed that HAP crystals were precipitated in the CPC containing 10 or 30wt% ZCP after successfully hardening. However, the crystal growth observed by scanning electron microscopy was delayed in the presence of additional ZCP. These findings indicate that the additional zinc inhibits crystal growth and the conversion of CPC to the HAP crystals. The proliferation of the cells and alkaline phosphatase (ALP) activity were enhanced when 10wt% ZCP was added to CPC. Taken together, ZCP added CPC at an appropriate fraction has a potent promotional effect on bone substitute biomaterials.

  2. Seed selections for crystallization of calcium phosphate for phosphorus recovery

    Institute of Scientific and Technical Information of China (English)

    SONG Yong-hui; Dietfried DONNERT; Ute BERG; Peter G. WEIDLER; Rolf NUEESCH

    2007-01-01

    Seed induces and promotes the crystallization of calcium phosphate, and acts as carrier of the recovered phosphorus (P). In order to select suitable seed for P recovery from wastewater, three seeds including Apatite (AP), Juraperle (JP) and phosphate-modified Juraperle (M-JP) were tested and compared. Batch and fixed-bed column experiments of seeded crystallization of calcium phosphate were undertaken by using synthetic wastewater with 10 mg/L P phosphate. It shows that AP has bad enduring property in the crystallization process, while JP has better performance for multiple uses, and M-JP is a hopeful seed for P recovery by crystallization of calcium phosphate.

  3. Deposition of calcium phosphate coatings using condensed phosphates (P2O7(4-) and P3O10(5-)) as phosphate source through induction heating.

    Science.gov (United States)

    Zhou, Huan; Hou, Saisai; Zhang, Mingjie; Yang, Mengmeng; Deng, Linhong; Xiong, Xinbo; Ni, Xinye

    2016-12-01

    In present work condensed phosphates (P2O7(4-) and P3O10(5-)) were used as phosphate source in induction heating to deposit calcium phosphate coatings. The phase, morphology, and composition of different phosphate-related coatings were characterized and compared using XRD, FTIR, and SEM analyses. Results showed that P2O7(4-)formed calcium pyrophosphate hydrate coatings with interconnected cuboid-like particles. The as-deposited calcium tripolyphosphate hydrate coating with P3O10(5-) was mainly composed of flower-like particles assembled by plate-like crystals. The bioactivity and cytocompatibility of the coatings were also studied. Moreover, the feasibility of using hybrid phosphate sources for preparing and depositing coatings onto magnesium alloy was investigated.

  4. Is there a chemical interaction between calcium phosphates and organic compounds in the organic/inorganic composites?

    Energy Technology Data Exchange (ETDEWEB)

    Dorozhkin, S.V. [Research Inst. of Fertilisers, Moscow (Russian Federation)

    2001-07-01

    Solid composites of three biologically relevant calcium phosphates and hydroxypropylmethylcellulose (HPMC) were prepared at temperatures of 121 C. Properties of the composites obtained were studied by FTIR, X-ray diffraction, and SEM techniques. Special attention was devoted to seeking of a possible chemical interaction between the calcium phosphates and HPMC. No chemical interaction was found. Thus, HPMC was proven to have no influence on the chemical properties of calcium phosphates. (orig.)

  5. Nanostructured calcium-silver phosphate composite powder, method for obtaining same, and bactericidal and fungicidal uses thereof

    OpenAIRE

    Díaz Muñoz, Marcos; Moya, J. S.; Barba Martín-Sonseca, María Flora; Malpartida Romero, Francisco; Miranda Fernández, Miriam; Fernández, Adolfo

    2008-01-01

    [EN] The invention relates to a nanostructured calcium-silver phosphate composite powder which can be used as a bactericide and/or fungicide, with similar effectiveness to that of commercial products and with low toxicity. The invention also relates to a method for obtaining said nanostructured calcium-silver phosphate composite powders, which comprises preparing nanometric calcium phosphate by means of a sol-gel process and subsequently depositing silver nanoparticles on the surface thereof....

  6. [Synthetic calcium phosphate ceramics in secondary alveoloplasty].

    Science.gov (United States)

    Corre, P; Khonsari, R-H; Laure, B; Elamrani, K; Weiss, P; Mercier, J-M

    2012-04-01

    Bone substitutes are rarely used in the reconstruction of cleft lip and palate. The graft material of choice is cancellous bone, harvested in the hip or tibia. Tibial harvesting may lead to postoperative morbidity, or even complications. This has lead surgeons to develop alternative solution. We present a secondary alveolar bone grafting technique using synthetic calcium phosphate ceramics. A patient presenting with a complete unilateral cleft lip and palate was treated by alveolar bone grafting at the age of nine years, using a mixture of autologous bone, harvested on the operative field, and particles of biphasic calcium phosphate (BCP); the graft was included in a platelet rich plasma (PRP) gel. The patient was followed up for eight years after the procedure. No sign of early or late infection was observed. At the end of facial growth, the cuspid had erupted correctly in a safe periodontal environment. Sequential X-rays showed complete filling of the initial bone defect, progressive resorption of ceramics, and spontaneous eruption of the cuspid. In this long-term follow-up report, the use of BCP mixed with autologous bone did not interfere with dental eruption or maxilla growth. A second bone-harvesting site was thus avoided. BCP could be a suitable alternative to autologous bone graft for secondary alveoloplasty. Copyright © 2012 Elsevier Masson SAS. All rights reserved.

  7. Selective laser sintering of calcium phosphate materials for orthopedic implants

    Science.gov (United States)

    Lee, Goonhee

    Two technologies, Solid Freeform Fabrication (SFF) and bioceramics are combined in this work to prepare bone replacement implants with complex geometry. SFF has emerged as a crucial technique for rapid prototyping in the last decade. Selective Laser Sintering (SLS) is one of the established SFF manufacturing processes that can build three-dimensional objects directly from computer models without part-specific tooling or human intervention. Meanwhile, there have been great efforts to develop implantable materials that can assist in regeneration of bone defects and injuries. However, little attention has been focused in shaping bones from these materials. The main thrust of this research was to develop a process that can combine those two separate efforts. The specific objective of this research is to develop a process that can construct bone replacement material of complex geometry from synthetic calcium phosphate materials by using the SLS process. The achievement of this goal can have a significant impact on the quality of health care in the sense that complete custom-fit bone and tooth structures suitable for implantation can be prepared within 24--48 hours of receipt of geometric information obtained either from patient Computed Tomographic (CT) data, from Computer Aided Design (CAD) software or from other imaging systems such as Magnetic Resonance Imaging (MRI) and Holographic Laser Range Imaging (HLRI). In this research, two different processes have been developed. First is the SLS fabrication of porous bone implants. In this effort, systematic procedures have been established and calcium phosphate implants were successfully fabricated from various sources of geometric information. These efforts include material selection and preparation, SLS process parameter optimization, and development of post-processing techniques within the 48-hour time frame. Post-processing allows accurate control of geometry and of the chemistry of calcium phosphate, as well as

  8. A kinetic study of precipitation from supersaturated calcium phosphate solutions

    NARCIS (Netherlands)

    Kemenade, M.J.J.M. van; Bruyn, P.L. de

    The formation of three different crystalline calcium phosphates (DCPD, OCP, HAP) and an amorphous calcium phosphate was studied as a function of pH and supersaturation. Under the experimental conditions the formation of HAP is always found to be preceded by one or more precursors in a sequence that

  9. Odontoblast phosphate and calcium transport in dentinogenesis.

    Science.gov (United States)

    Lundquist, Patrik

    2002-01-01

    It has been suggested that odontoblasts are instrumental in translocating Ca2+ and inorganic phosphate (Pi) ions during the mineralization of dentin. The aim of this thesis was, therefore, to study the expression of components of the transcellular ion transport system, Na+/Ca2+ exchangers and Na(+)-Pi contransporters, in odontoblastic and osteoblastic cells. Their activity was assayed in osteoblast-like cells and in the recently developed MRPC-1 odontoblast-like cell line. To assess the relationship between ion transport and mineralization, Ca2+ and Pi uptake activities were determined in mineralizing cultures of MRPC-1 cells. Osteoblastic and odontoblastic cells showed an identical expression pattern of Na+/Ca2+ exchanger splice-variants, NCX1.3, NCX1.7 and NCX1.10, derived from the NCX1 gene, while NCX2 was not expressed. The cells showed a high sodium-dependent calcium extrusion activity. Regarding Na(+)-Pi cotransporter expression, Glvr-1, Ram-1 and the two high capacity cotransporters Npt-2a and Npt-2b were found to be expressed in odontoblasts and MRPC-1 cells. Osteoblast-like cells differed from this in expressing the Npt-1 but not the Ram-1 gene but were otherwise identical to the odontoblastic cells. Odontoblast-like cells exhibited almost twice the sodium-dependent Pi uptake activity of osteoblast-like cells. The presence of NaPi-2a and NaPi-2b, gene products of Npt-2a and Npt-2b, was verified in vivo by immunohistochemistry on mouse teeth. Both cotransporters could be detected in fully differentiated, polarized odontoblasts but not in preodontoblasts prior to dentin formation. Both cotransporters were detected in adjacent bone and in ameloblasts. Studying ion uptake in mineralizing MRPC-1 cultures, large changes were detected concomitant with the onset of mineral formation, when phosphate uptake increased by 400% while calcium uptake started to decline. The increase in Pi uptake was found to be due to activation of the NaPi-2a cotransporter. MRPC-1 cells

  10. Characterization of a calcium phosphate cement based on alpha-tricalcium phosphate obtained by wet precipitation process

    Energy Technology Data Exchange (ETDEWEB)

    Thurmer, M.B.; Diehl, C.E.; Vieira, R.S.; Coelho, W.T.G.; Santos, L.A., E-mail: monicathurmer@yahoo.com [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil). Dept. de Engenharia de Materiais

    2012-07-01

    There are several systems of calcium phosphate cements being studied. Those based on alpha-tricalcium phosphate are of particular interest. After setting they produce calcium deficient hydroxyapatite similar to bone like hydroxyapatite. This work aims to obtain alpha-tricalcium phosphate powders by the wet precipitation process, using calcium nitrate and phosphoric acid as reagents. This powder was characterized by infrared spectroscopy, X-ray diffraction and particle size distribution. In order to prepare the calcium phosphate cement, the powder was mixed with an accelerator in an aqueous solution. The mechanical properties of the cement were assessed and it was evaluated by means of apparent density, X-ray diffraction and scanning electron microscopy. The described method produced crystalline alpha-tricalcium phosphate as the major phase. The calcium phosphate cement showed high values of compression strength (50 MPa). The soaking of the cement in a simulated body fluid (SBF) formed a layer of hydroxyapatite like crystals in the surface of the samples. (author)

  11. Pathogenic Mineralization of Calcium Phosphate on Human Heart Valves

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    When calcium phosphate forms in soft tissues such as blood vessels and heart valves, it causes disease. The abnormal formation of calcium phosphate is called pathogenic mineralization or pathogenic calcification. Cases of rheumatic heart disease (RHD) always occur with fibrotic and calcified tissue of heart valve. In this article, samples taken from calcified human heart valves were studied. The characterization was performed by scanning electronic micrascope, X-ray Diffraction and transmission electron microscopy with selective diffraction patterns. It is found for the first time that calcium phosphate grains existing in the calcified human heart valves contain octacalcium phosphate (OCP).

  12. PREPARATION AND CHARACTERIZATION OF MACROPOROUS CALCIUM PHOSPHATE CEMENT SCAFFOLD WITH ORIENTED PORE STRUCTURE%具有定向孔隙结构的大孔磷酸钙骨水泥支架的制备与表征

    Institute of Scientific and Technical Information of China (English)

    漆小鹏; 叶建东; 王秀鹏; 王迎军

    2007-01-01

    A macroporous calcium phosphate cement scaffold with oriented pore structure is prepared by freeze casting. The pore structure and phases formed were evaluated by scanning electron microscope(SEM)and X-ray diffraction (XRD). The photographs of SEM show that the porous calcium phosphate cements have interconnected macropores aligned along the ice growth direction and the sizes of the open interconnected macropores can reach 150μm and 200 μm in their radial dimension and 500-1 000 μmn in the axial one. The pore size could be adjusted by the freezing parameters to match the requirements for bone tissue. The XRD patterns of the specimens show that poorly crystallized hydroxyapatite (HA) was the main phase present in the porous calcium phosphate cement.The porosity of the samples could be regulated from about 70% to 90% by the adjustment of the initial liquid to powder mass ratio.The macroporous calcium phosphate cement prepared in this work might be a potential scaffold for bone tissue engineering.%利用冷冻塑形法制备了具有定向孔隙结构的大孔磷酸钙骨水泥支架.利用扫描电镜(scanning electron microscope,SEM)和x射线衍射(X-ray diffraction,XRD)对材料的孔隙结构和物相进行了研究.SEM照片显示:多孔磷酸钙骨水泥具有与冰晶生长方向一致的相互连通的大孔.开口大孔的尺寸在径向能达到150~200 μm,在轴向能达到500~1 000 μm.孔隙的大小可以通过改变冷冻参数进行调节.XRD谱显示:多孔磷酸钙骨水泥中的主要相为弱结晶的羟基磷灰石.材料的孔隙率可以通过调整液固比在70%到90%之间进行调节.实验制备的大孔磷酸钙骨水泥支架是很有希望的骨组织工程支架材料.

  13. Kinetics of dissolution of calcium phosphate (Ca-P bioceramics

    Directory of Open Access Journals (Sweden)

    Lukas Brazda

    2008-06-01

    Full Text Available Hydroxyapatite (HAp and β-tricalcium phosphate (β-TCP are widely used bioceramics for surgical or dental applications. This paper is dealing with dissolution kinetics of synthetically prepared β-TCP and four types of HAp granules. Two groups of HAp, treated at different temperatures, each of them with two different granule sizes, were tested. Three corrosive solutions with different pH and simulated body fluid (SBF were used for immersing of the samples. Changes in concentrations of calcium and phosphate ions, pH level and weight changes of the samples were observed. It was found that presence of TRIS buffer enhanced dissolution rate of the β-TCP approximately two times. When exposed to SBF solution, calcium phosphate (most probably hydroxyapatite precipitation predominates over β-TCP dissolution. Results from HAp samples dissolution showed some unexpected findings. Neither heat treatment nor HAp particle size made any major differences in dissolution rate of the same mass of each HAp sample.

  14. Effect of the calcium to phosphate ratio of tetracalcium phosphate on the properties of calcium phosphate bone cement.

    Science.gov (United States)

    Burguera, Elena F; Guitian, Francisco; Chow, Laurence C

    2008-06-01

    Six different tetracalcium phosphate (TTCP) products were synthesized by solid state reaction at high temperature by varying the overall calcium to phosphate ratio of the synthesis mixture. The objective was to evaluate the effect of the calcium to phosphate ratio on a TTCP-dicalcium phosphate dihydrate (DCPD) cement. The resulting six TTCP-DCPD cement mixtures were characterized using X-ray diffraction analysis, scanning electron microscopy, and pH measurements. Setting times and compressive strength (CS) were also measured. Using the TTCP product with a Ca/P ratio of 2.0 resulted in low strength values (25.61 MPa) when distilled water was used as the setting liquid, even though conversion to hydroxyapatite was not prevented, as confirmed by X-ray diffraction. The suspected CaO presence in this TTCP may have affected the cohesiveness of the cement mixture but not the cement setting reaction, however no direct evidence of CaO presence was found. Lower Ca/P ratio products yielded cements with CS values ranging from 46.7 MPa for Ca/P ratio of 1.90 to 38.32 MPa for Ca/P ratio of 1.85. When a dilute sodium phosphate solution was used as the setting liquid, CS values were 15.3% lower than those obtained with water as the setting liquid. Setting times ranged from 18 to 22 min when water was the cement liquid and from 7 to 8 min when sodium phosphate solution was used, and the calcium to phosphate ratio did not have a marked effect on this property.

  15. Serum Proteins Stabilized Calcium Phosphate Nanoparticles and Its Effect on Bel-7402 Cells

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Hydroxyapatite has a high affinity to biological macromolecules, especially to proteins. Bovine serum proteins were extracted to be used as stablizer to prepare calcium phosphate nanoparticles. 167.7 am and87.7 nm particles were respectively prepared by using bovine serum protein fractions at the concentration of 0.5mg/mL and 1.0 mg/mL. As the polysaccharide stabilized hydroxyapatite nanoparticles, the protein-stablized nanoparticles also inhibited the proliferation rate of Bel-7402 cells. It suggested that proteins could be applied to prepare calcium phosphate nanoparticles and it also has the anticancer effect.

  16. Influence of Ethylene Glycol on the Formation of Calcium Phosphate Nanocrystals

    Institute of Scientific and Technical Information of China (English)

    Yi ZUO; Yubao LI; Jie WEI; Yonggang YAN

    2003-01-01

    A synthesis route of using calcium hydroxide Ca(OH)2 with ethylene glycol solvent and orthophosphoric acid (H3PO4)as reagents is described. Three ratios of ethylene glycol to distilled water 1:0, 1:1 and 0:1 are used as diluting media for Ca(OH)2. Crystals of different morphology and composition are formed under weak alkaline circumstance at pH 7.0~8.0. Acicular calcium phosphate nanocrystals are prepared in pure ethylene glycol while rod-like calcium phosphate nanocrystals form in pure distilled water. The nanograde size of the former is smaller than that of the latter. Calcium-deficient apatite (CDAP) is obtained with a Ca/P molar ratio of 1.66. Therefore, it was deduced that the usage of ethylene glycol solvent could influence the formation of calcium phosphate crystal lattice.

  17. In-situ mineralization of chitosan/calcium phosphate composite and the effect of solvent on the structure

    Science.gov (United States)

    He, Ling-Hao; Yao, Lu; Xue, Rui; Sun, Jing; Song, Rui

    2011-09-01

    Solvent played an important role in the formation of calcium phosphate phase of the chitosan/calcium phosphate composites. In this investigation, ethanolacetic acid mixtures were employed as solvents, and various calcium phosphate phases, such as brushite, amorphous calcium phosphate, and hydroxyapatite, were introduced into the chitosan/calcium phosphate composites by using in-situ preparation process. The results showed that the structures of composite were influenced remarkably by the morphology and the distribution of calcium phosphate phase. In addition, the bioactivity of composites was governed mainly by the characters of calcium phosphate phases in composites, since calcium phosphate phases could induce the growth of hydroxyapatite coating on the surfaces of composites. On the surface of chitosan/brushite composite, the formed hydroxyapatite coating consisted of oriented plate crystallites, which selfassembled into spherical-like crystals. When other calcium phosphate phase was introduced into composites, the polymorphs of hydroxyapatite layer would change greatly. The oriented plate crystallites became bigger, and meanwhile, the self-assembled aggregates became less and smaller. In addition, with the shift of the prior nucleating point, the growth orientation of plate crystallites was transformed.

  18. Microanalyses of the hydroxyl—poly—calcium sodium phosphate coatings produced by ion beam assisted deposition

    Institute of Scientific and Technical Information of China (English)

    LIUZhong-Yang; WANGChang-Xing; 等

    2002-01-01

    Thin calcium phosphate catings on titanium alloy substrates were prepared by Ar+ ion beam assisted deposition(IBAD) from hydroxyl-poly-calcium sodium phosphate(HPPA) target.The coatings were analyzed by XRD,FTIR,XPS,These analyses revealed that the as-deposited films were amorphous or no apparent crystallinity.No distinct absorption band of the hydroxyl group was observed in FTIR spectra of the coatings but new absorption bands were presented for CO3-2,The calcium to phosphorous ratio of these catings in different IBAD conditions varied from 0.46 to 3.36.

  19. Calcium phosphate formation in aqueous suspensions of multilamellar liposomes.

    Science.gov (United States)

    Eanes, E D; Hailer, A W; Costa, J L

    1984-07-01

    The present study examined calcium phosphate precipitation in aqueous suspensions of multilamellar liposomes as a possible in vitro model for matrix vesicle mineralization. Liposomes were prepared by dispersing CHCl3-evaporated thin films of 7:2:1 and 7:1:1 molar mixtures of phosphatidylcholine, dicetyl phosphate, and cholesterol in aqueous solutions containing 0, 25, or 50 mM PO4 and 0 or 0.8 mM Mg. After removal of unencapsulated PO4 by gel filtration, the liposomes were suspended in 1.33 mM Ca/0.8 mM Mg solutions and made permeable to these cations by the addition of the ionophore X-537A. All experiments were carried out at pH 7.4, 22 degrees C, and 240 mOsm. In the absence of entrapped PO4, Ca2+ taken up by the liposomes was largely bound to inner membrane surfaces. With PO4 present, Ca2+ uptake increased as much as sixfold with maximum accumulations well above values sufficient for solid formation. Precipitated solids appeared to be located predominantly in the aqueous intermembranous spaces of the liposomes. Amorphous calcium phosphate (ACP) precipitated initially in the presence of entrapped Mg2+, then subsequently converted to apatite intermixed with some octacalcium phosphate. The stability of the liposomal ACP was somewhat greater than that observed in bulk solutions under comparable conditions of pH, temperature, and electrolyte makeup. In time, the mineral deposits caused entrapped PO4 to leak from the liposomes. These findings suggest that the precipitation within liposomes is similar to that which occurs in macro-volume synthetic systems but that the precipitated solid eventually impairs the integrity of the surrounding intermembranous space.(ABSTRACT TRUNCATED AT 250 WORDS)

  20. Role of magnesium on the biomimetic deposition of calcium phosphate

    Science.gov (United States)

    Sarma, Bimal K.; Sarma, Bikash

    2016-10-01

    Biomimetic depositions of calcium phosphate (CaP) are carried out using simulated body fluid (SBF), calcifying solution and newly developed magnesium containing calcifying solution. Calcium phosphate has a rich phase diagram and is well known for its excellent biocompatibility and bioactivity. The most common phase is hydroxyapatite (HAp), an integral component of human bone and tooth, widely used in orthopedic and dental applications. In addition, calcium phosphate nanoparticles show promise for the targeted drug delivery. The doping of calcium phosphate by magnesium, zinc, strontium etc. can change the protein uptake by CaP nanocrystals. This work describes the role of magnesium on the nucleation and growth of CaP on Ti and its oxide substrates. X-ray diffraction studies confirm formation of HAp nanocrystals which closely resemble the structure of bone apatite when grown using SBF and calcifying solution. It has been observed that magnesium plays crucial role in the nucleation and growth of calcium phosphate. A low magnesium level enhances the crystallinity of HAp while higher magnesium content leads to the formation of amorphous calcium phosphate (ACP) phase. Interestingly, the deposition of ACP phase is rapid when magnesium ion concentration in the solution is 40% of calcium plus magnesium ions concentration. Moreover, high magnesium content alters the morphology of CaP films.

  1. Proliferation and differentiation of osteoblast-like MC3T3-E1 cells on biomimetically and electrolytically deposited calcium phosphate coatings

    NARCIS (Netherlands)

    Wang, Jiawei; Boer, de Jan; Groot, de Klaas

    2008-01-01

    Biomimetic and electrolytic deposition are versatile methods to prepare calcium phosphate coatings. In this article, we compared the effects of biomimetically deposited octacalcium phosphate and carbonate apatite coatings as well as electrolytically deposited carbonate apatite coating on the prolife

  2. Reinforcement Strategies for Load-Bearing Calcium Phosphate Biocements

    Directory of Open Access Journals (Sweden)

    Martha Geffers

    2015-05-01

    Full Text Available Calcium phosphate biocements based on calcium phosphate chemistry are well-established biomaterials for the repair of non-load bearing bone defects due to the brittle nature and low flexural strength of such cements. This article features reinforcement strategies of biocements based on various intrinsic or extrinsic material modifications to improve their strength and toughness. Altering particle size distribution in conjunction with using liquefiers reduces the amount of cement liquid necessary for cement paste preparation. This in turn decreases cement porosity and increases the mechanical performance, but does not change the brittle nature of the cements. The use of fibers may lead to a reinforcement of the matrix with a toughness increase of up to two orders of magnitude, but restricts at the same time cement injection for minimal invasive application techniques. A novel promising approach is the concept of dual-setting cements, in which a second hydrogel phase is simultaneously formed during setting, leading to more ductile cement–hydrogel composites with largely unaffected application properties.

  3. Biomimetic calcium phosphate coatings on recombinant spider silk fibres

    NARCIS (Netherlands)

    Yang, Liang; Hedhammar, My; Blom, Tobias; Leifer, Klaus; Johansson, Jan; Habibovic, Pamela; van Blitterswijk, Clemens

    2010-01-01

    Calcium phosphate ceramic coatings, applied on surfaces of metallic and polymeric biomaterials, can improve their performance in bone repair and regeneration. Spider silk is biocompatible, strong and elastic, and hence an attractive biomaterial for applications in connective tissue repair. Recently,

  4. Biomimetic calcium phosphate coatings on recombinant spider silk fibres

    NARCIS (Netherlands)

    Yang, Liang; Hedhammar, My; Blom, Tobias; Leifer, Klaus; Johansson, Jan; Habibovic, Pamela; Blitterswijk, van Clemens A.

    2010-01-01

    Calcium phosphate ceramic coatings, applied on surfaces of metallic and polymeric biomaterials, can improve their performance in bone repair and regeneration. Spider silk is biocompatible, strong and elastic, and hence an attractive biomaterial for applications in connective tissue repair. Recently,

  5. Effect of humic substances on the precipitation of calcium phosphate

    Institute of Scientific and Technical Information of China (English)

    SONG Yong-hui; Hermann H. HAHN; Erhard HOFFMANN; Peter G. WEIDLER

    2006-01-01

    For phosphorus (P) recovery from wastewater, the effect of humic substances (HS) on the precipitation of calcium phosphate was studied. Batch experiments of calcium phosphate precipitation were undertaken with synthetic water that contained 20 mg/L phosphate (as P) and 20 mg/L HS (as dissolved organic carbon, DOC) at a constant pH value in the range of 8.0-10.0. The concentration variations of phosphate, calcium (Ca) and HS were measured in the precipitation process; the crystalline state and compositions of the precipitates were analysed by powder X-ray diffraction (XRD) and chemical methods, respectively. It showed that at solution pH 8.0, the precipitation rate and removal efficiency of phosphate were greatly reduced by HS, but at solution pH ≥9.0,the effect of HS was very small. The Ca consumption for the precipitation of phosphate increased when HS was added; HS was also removed from solution with the precipitation of calcium phosphate. At solution pH 8.0 and HS concentrations ≤ 3.5 mg/L, and at pH ≥ 9.0 and HS concentrations ≤ 10 mg/L, the final precipitates were proved to be hydroxyapatite (HAP) by XRD. The increases of solution pH value and initial Ca/P ratio helped reduce the influence of HS on the precipitation of phosphate.

  6. Chemistry Misconceptions Associated with Understanding Calcium and Phosphate Homeostasis

    Science.gov (United States)

    Cliff, William H.

    2009-01-01

    Successful learning of many aspects in physiology depends on a meaningful understanding of fundamental chemistry concepts. Two conceptual diagnostic questions measured student understanding of the chemical equilibrium underlying calcium and phosphate homeostasis. One question assessed the ability to predict the change in phosphate concentration…

  7. Preparation of porous lanthanum phosphate with templates

    Energy Technology Data Exchange (ETDEWEB)

    Onoda, Hiroaki, E-mail: onoda@kpu.ac.jp [Department of Informatics and Environmental Sciences, Faculty of Life and Environmental Sciences, Kyoto Prefectural University, 1-5, Shimogamo Nakaragi-cyo, Sakyo-ku, Kyoto 606-8522 (Japan); Ishima, Yuya [Department of Applied Chemistry, Faculty of Life Sciences, Ritsumeikan University, 1-1-1, Nojihigashi, Kusatsu, Shiga 525-8577 (Japan); Takenaka, Atsushi [Department of Materials Science, Yonago National College of Technology, 4448, Hikona-cho, Yonago, Tottori 683-8502 (Japan); Tanaka, Isao [Department of Materials Science and Engineering, Faculty of Engineering, Kyoto University, Yoshida-Honmachi, Sakyo-ku, Kyoto 606-8501 (Japan)

    2009-08-05

    Malonic acid, propionic acid, glycine, n-butylamine, and urea were added to the preparation of lanthanum phosphate from lanthanum nitrate and phosphoric acid solutions. All additives were taken into lanthanum phosphate particles. The additives that have a basic site were easy to contain in precipitates. The addition of templates improved the specific surface area of lanthanum phosphate. The amount of pore, with radius smaller than 4 nm, increased with the addition of templates. The remained additives had influence on the acidic properties of lanthanum phosphate.

  8. Calcium phosphate precipitation modeling in a pellet reactor

    OpenAIRE

    Montastruc, Ludovic; Azzaro-Pantel, Catherine; Cabassud, Michel; Biscans, Béatrice

    2002-01-01

    The calcium phosphate precipitation in a pellet reactor can be evaluated by two main parameters: the phosphate conversion ratio and the phosphate removal efficiency. The conversion ratio depends mainly on the pH. The pellet reactor efficiency depends not only on pH but also on the hydrodynamical conditions. An efficiency model based on a thermochemical precipitation approach and an orthokinetic aggregation model is presented. In this paper, the results show that optimal conditions for pellet ...

  9. Biomimetic fabrication of calcium phosphate/chitosan nanohybrid composite in modified simulated body fluids

    Directory of Open Access Journals (Sweden)

    K. H. Park

    2017-01-01

    Full Text Available In this study, nucleation and growth of bone-like hydroxyapatite (HAp mineral in modified simulated body fluids (m-SBF were induced on chitosan (CS substrates, which were prepared by spin coating of chitosan on Ti substrate. The m-SBF showed a two fold increase in the concentrations of calcium and phosphate ions compared to SBF, and the post-NaOH treatment provided stabilization of the coatings. The calcium phosphate/chitosan composite prepared in m-SBF showed homogeneous distribution of approximately 350 nm-sized spherical clusters composed of octacalcium phosphate (OCP; Ca8H2(PO46·5H2O crystalline structure. Chitosan provided a control over the size of calcium phosphate prepared by immersion in m-SBF, and post-NaOH treatment supported the binding of calcium phosphate compound on the Ti surface. Post-NaOH treatment increased hydrophilicity and crystallinity of carbonate apatite, which increased its potential for biomedical application.

  10. Associations between calcium-phosphate metabolism and coronary artery calcification

    DEFF Research Database (Denmark)

    Grønhøj, Mette H; Gerke, Oke; Mickley, Hans;

    2016-01-01

    calcium-phosphate metabolism is associated with the presence and extent of coronary artery calcification (CAC) in asymptomatic and apparently healthy individuals. METHODS: Serum samples from 1088 randomly recruited middle-aged men and women without known CVD and diabetes (DM), from the general population......, were analysed for total calcium, phosphate, parathyroid hormone (PTH) and 25-hydroxyvitamin D (25(OH)D). CAC was measured by a non-contrast cardiac CT scan and categorised into four groups: 0, 1-99, 100-399, ≥400 Agatston units. The association of calcium-phosphate metabolism with CAC was evaluated......)D values were placed within the normal range. In men, the odds of being in a higher CAC category, i.e. having more severe CAC, increased by 30% when serum calcium concentration increased by 0.1 mmol/l (95% CI: 1.04-1.61, p = 0.019), independently of traditional cardiovascular risk factors. In women...

  11. Effects of Additives on Sintering and Characterization of Calcium Phosphate Ceramics

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Calcium phosphate precursory powders containing Na and Mg have been prepared by the citric acid sol-gel combustion method. The elements of Na and Mg were introduced from component of CaO- P2O5-Na2 O-MgO. The effect of sintering additives on the phase composition was characterized by XRD. The effect of sintering additives on sintering of materials was also characterized by linear shrinkage, TEM and SEM. Finally the microstructure of porous calcium phosphate ceramic was determined by SEM.

  12. Synthesis and characterization of porous calcium phosphate; Sintesis y caracterizacion del fosfato de calcio poroso

    Energy Technology Data Exchange (ETDEWEB)

    Granados C, F.; Serrano G, J.; Bonifacio M, J. [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)]. e-mail: fgc@nuclear.inin.mx

    2007-07-01

    The porous calcium phosphate was prepared by the continuous precipitation method using Ca(NO{sub 3}){sub 2}.4H{sub 2}O and NH{sub 4}H{sub 2}PO{sub 4} salts. The synthesized material was structurally and superficially characterized using the XRD, BET, IR TGA and SEM techniques. The obtained inorganic material was identified as calcium phosphate that presents a great specific area for what can be efficiently used as adsorbent material for adsorption studies in the radioactive wastes treatment present in aqueous solution. (Author)

  13. Brushite-based calcium phosphate cement with multichannel hydroxyapatite granule loading for improved bone regeneration.

    Science.gov (United States)

    Sarkar, Swapan Kumar; Lee, Byung Yeol; Padalhin, Andrew Reyas; Sarker, Avik; Carpena, Nathaniel; Kim, Boram; Paul, Kallyanshish; Choi, Hwan Jun; Bae, Sang-Ho; Lee, Byong Taek

    2016-01-01

    In this work, we report brushite-based calcium phosphate cement (CPC) system to enhance the in vivo biodegradation and tissue in-growth by incorporation of micro-channeled hydroxyapatite (HAp) granule and silicon and sodium addition in calcium phosphate precursor powder. Sodium- and silicon-rich calcium phosphate powder with predominantly tri calcium phosphate (TCP) phase was synthesized by an inexpensive wet chemical route to react with mono calcium phosphate monohydrate (MCPM) for making the CPC. TCP nanopowder also served as a packing filler and moderator of the reaction kinetics of the setting mechanism. Strong sintered cylindrical HAp granules were prepared by fibrous monolithic (FM) process, which is 800 µm in diameter and have seven micro-channels. Acid sodium pyrophosphate and sodium citrate solution was used as the liquid component which acted as a homogenizer and setting time retarder. The granules accelerated the degradation of the brushite cement matrix as well as improved the bone tissue in-growth by permitting an easy access to the interior of the CPC through the micro-channels. The addition of micro-channeled granule in the CPC introduced porosity without sacrificing much of its compressive strength. In vivo investigation by creating a critical size defect in the femur head of a rabbit model for 1 and 2 months showed excellent bone in-growth through the micro-channels. The granules enhanced the implant degradation behavior and bone regeneration in the implanted area was significantly improved after two months of implantation.

  14. The use of size-defined DNA-functionalized calcium phosphate nanoparticles to minimise intracellular calcium disturbance during transfection.

    Science.gov (United States)

    Neumann, Sebastian; Kovtun, Anna; Dietzel, Irmgard D; Epple, Matthias; Heumann, Rolf

    2009-12-01

    Calcium phosphate-based transfection methods are frequently used to transfer DNA into living cells. However, it has so far not been studied in detail to what extend the different transfection methods lead to a net calcium uptake. Upon subsequent resolution of the calcium phosphate, intracellular free ionic calcium-surges could result, inducing as side effect various physiological responses that may finally result in cell death. Here we investigated the overall calcium uptake by the human bladder carcinoma cell line T24 during the standard calcium phosphate transfection method and also during transfection with custom-made calcium phosphate/DNA nanoparticles by isotope labelling with (45)calcium. (45)Calcium uptake was strongly increased after 7h of standard calcium phosphate transfection but not if the transfection was performed with calcium phosphate nanoparticles. Time lapse imaging microscopy using the calcium-sensitive dye Fura-2 revealed large transient increases of the intracellular free calcium level during the standard calcium phosphate transfection but not if calcium phosphate nanoparticles were used. Consistently, the viability of cells transfected by calcium phosphate/DNA nanoparticles was not changed, in remarkable contrast to the standard method where considerable cell death occurred.

  15. Renal control of calcium, phosphate, and magnesium homeostasis.

    Science.gov (United States)

    Blaine, Judith; Chonchol, Michel; Levi, Moshe

    2015-07-01

    Calcium, phosphate, and magnesium are multivalent cations that are important for many biologic and cellular functions. The kidneys play a central role in the homeostasis of these ions. Gastrointestinal absorption is balanced by renal excretion. When body stores of these ions decline significantly, gastrointestinal absorption, bone resorption, and renal tubular reabsorption increase to normalize their levels. Renal regulation of these ions occurs through glomerular filtration and tubular reabsorption and/or secretion and is therefore an important determinant of plasma ion concentration. Under physiologic conditions, the whole body balance of calcium, phosphate, and magnesium is maintained by fine adjustments of urinary excretion to equal the net intake. This review discusses how calcium, phosphate, and magnesium are handled by the kidneys.

  16. Characterization of calcium phosphate powders originating from Phyllacanthus imperialis and Trochidae Infundibulum concavus marine shells

    Energy Technology Data Exchange (ETDEWEB)

    Tămăşan, M., E-mail: monica.tamasan@phys.ubbcluj.ro [Babeş-Bolyai University, Faculty of Physics and Interdisciplinary Research Institute on Bio-Nano-Sciences, Cluj-Napoca (Romania); Ozyegin, L.S. [Marmara University, Istanbul (Turkey); Oktar, F.N. [Marmara University, Faculty of Engineering, Department of Bioengineering, Göztepe Campus, Kadıköy 34722, Istanbul (Turkey); Marmara University, School of Health Related Professions, Department of Medical Imaging Technics, Haydarpaşa Campus, Tıbbiye Street, 49, Üsküdar 34668, Istanbul (Turkey); Marmara University, Nanotechnology and Biomaterials Application and Research Centre, Göztepe Campus, Kadıköy 34722, Istanbul (Turkey); Simon, V. [Babeş-Bolyai University, Faculty of Physics and Interdisciplinary Research Institute on Bio-Nano-Sciences, Cluj-Napoca (Romania)

    2013-07-01

    The study reports the preparation and characterization of powders consisting of the different phases of calcium phosphates that were obtained from the naturally derived raw materials of sea-shell origins reacted with H{sub 3}PO{sub 4}. Species of sea origin, such as corals and nacres, attracted a special interest in bone tissue engineering area. Nacre shells are built up of calcium carbonate in aragonite form crystallized in an organic matrix. In this work two natural marine origin materials (shells of echinoderm Sputnik sea urchin — Phyllacanthus imperialis and Trochidae Infundibulum concavus mollusk) were involved in the developing powders of calcium phosphate based biomaterials (as raw materials for bone-scaffolds) by hotplate and ultrasound methods. Thermal analyses of the as-prepared materials were made for an assessment of the thermal behavior and heat treatment temperatures. Samples from both sea shells each of them prepared by the above mentioned methods were subjected to thermal treatments at 450 °C and 850 °C in order to evaluate the crystalline transformations of the calcium phosphate structures in the heating process. By X-ray diffraction analyses various calcium phosphate phases were identified. In Sputnik sea urchins originated samples were found predominantly brushite and calcite as a small secondary phase, while in Trochidae I. concavus samples mainly monetite and HA phases were identified. Thermal treatment at 850 °C resulted flat-plate whitlockite crystals — β-MgTCP [(Ca, Mg){sub 3} (PO{sub 4}){sub 2}] for both samples regardless the preparation method (ultrasound or hotplate) or the targeted Ca/P molar ratio according with XRD patterns. Scanning electron microscopy and Fourier transformed infrared spectroscopy were involved more in the characterization of these materials and the good correlations of the results of these methods were made. - Highlights: ► Calcium phosphate powders are obtained from the crushed shells of 2

  17. Sealing ability of mineral trioxide aggregate, calcium phosphate and polymethylmethacrylate bone cements on root ends prepared using an Erbium: Yttriumaluminium garnet laser and ultrasonics evaluated by confocal laser scanning microscopy.

    Science.gov (United States)

    Girish, C Sabari; Ponnappa, Kc; Girish, Tn; Ponappa, Mc

    2013-07-01

    Surgical endodontic therapy comprises of exposure of the involved root apex, resection of the apical end of the root, preparation of a class I cavity, and insertion of a root end filling material. Mineral trioxide aggregate (MTA) is now the gold standard among all root end filling materials. MTA is however difficult to handle, expensive and has a very slow setting reaction. (1) To compare the sealing ability of MTA, polymethylmethacrylate (PMMA) bone cement and CHITRA Calcium phosphate cement (CPC) when used as root end filling material using Rhodamine B dye evaluated under a confocal laser scanning microscope. (2) To compare the seal of root ends prepared using an ultrasonic retroprep tip and an Er: YAG laser using three different root end filling materials. Statistical analysis was performed using a one-way ANOVA and a two-way ANOVA, independent samples t-test and Scheffe's post hoc test using SPSS Version 16 for Windows. All the three materials, namely MTA, PMMA BONE CEMENT and CHITRA CPC, showed microleakage. Comparison of microleakage showed maximum peak value of 0.86 mm for MTA, 0.24 mm for PMMA bone cement and 1.37 mm for CHITRA CPC. The amount of dye penetration was found to be lesser in root ends prepared using Er: YAG laser when compared with ultrasonics, but the difference was found to be not statistically significant. PMMA bone cement is a better material as root end filling material to prevent apical microleakage. MTA still continues to be a gold standard root end filling material showing minimum microleakage. Er: YAG laser is a better alternative to ultrasonics for root end preparations.

  18. Rickets induced by calcium or phosphate depletion.

    OpenAIRE

    Abugassa, S.; Svensson, O.

    1990-01-01

    We studied the effects of calciopenia and phosphopenia on longitudinal growth, skeletal mineralization, and development of rickets in young Sprague-Dawley rats. At an age of 21 days, two experimental groups were given diets containing 0.02% calcium or 0.02% phosphorus; otherwise the diets were nutritionally adequate. After 7, 14, and 21 days, five animals from each group were randomly chosen. The animals were anaesthetized and blood samples were drawn for analysis of calcium, phosphorus, and ...

  19. Molecular mechanisms of crystallization impacting calcium phosphate cements

    Science.gov (United States)

    Giocondi, Jennifer L.; El-Dasher, Bassem S.; Nancollas, George H.; Orme, Christine A.

    2010-01-01

    The biomineral calcium hydrogen phosphate dihydrate (CaHPO4·2H2O), known as brushite, is a malleable material that both grows and dissolves faster than most other calcium minerals, including other calcium phosphate phases, calcium carbonates and calcium oxalates. Within the body, this ready formation and dissolution can play a role in certain diseases, such as kidney stone and plaque formation. However, these same properties, along with brushite’s excellent biocompatibility, can be used to great benefit in making resorbable biomedical cements. To optimize cements, additives are commonly used to control crystallization kinetics and phase transformation. This paper describes the use of in situ scanning probe microscopy to investigate the role of several solution parameters and additives in brushite atomic step motion. Surprisingly, this work demonstrates that the activation barrier for phosphate (rather than calcium) incorporation limits growth kinetics and that additives such as magnesium, citrate and bisphosphonates each influence step motion in distinctly different ways. Our findings provide details of how, and where, molecules inhibit or accelerate kinetics. These insights have the potential to aid in designing molecules to target specific steps and to guide synergistic combinations of additives. PMID:20308110

  20. Molecular mechanisms of crystallization impacting calcium phosphate cements.

    Science.gov (United States)

    Giocondi, Jennifer L; El-Dasher, Bassem S; Nancollas, George H; Orme, Christine A

    2010-04-28

    The biomineral calcium hydrogen phosphate dihydrate (CaHPO(4).2H(2)O), known as brushite, is a malleable material that both grows and dissolves faster than most other calcium minerals, including other calcium phosphate phases, calcium carbonates and calcium oxalates. Within the body, this ready formation and dissolution can play a role in certain diseases, such as kidney stone and plaque formation. However, these same properties, along with brushite's excellent biocompatibility, can be used to great benefit in making resorbable biomedical cements. To optimize cements, additives are commonly used to control crystallization kinetics and phase transformation. This paper describes the use of in situ scanning probe microscopy to investigate the role of several solution parameters and additives in brushite atomic step motion. Surprisingly, this work demonstrates that the activation barrier for phosphate (rather than calcium) incorporation limits growth kinetics and that additives such as magnesium, citrate and bisphosphonates each influence step motion in distinctly different ways. Our findings provide details of how, and where, molecules inhibit or accelerate kinetics. These insights have the potential to aid in designing molecules to target specific steps and to guide synergistic combinations of additives.

  1. Biomimetic Nanocomposites of Calcium Phosphate and Self-Assembling Triblock and Pentablock Copolymers

    Energy Technology Data Exchange (ETDEWEB)

    Enlow, Drew Lenzen [Iowa State Univ., Ames, IA (United States)

    2006-01-01

    In an effort to mimic the growth of natural bone, self-assembling, micelle and gel-forming copolymers were used as a template for calcium phosphate precipitation. Because of the cationic characteristics imparted by PDEAEM end group additions to commercially available Pluronic{reg_sign} Fl27, a direct ionic attraction mechanism was utilized and a polymer-brushite nanocomposite spheres were produced. Brushite coated spherical micelles with diameters of ~40 nm, and agglomerates of these particles (on the order of 0.5 μm) were obtained. Thickness and durability of the calcium phosphate coating, and the extent of agglomeration were studied. The coating has been shown to be robust enough to retain its integrity even below polymer critical micelle concentration and/or temperature. Calcium phosphate-polymer gel nanocomposites were also prepared. Gel samples appeared as a single phase network of agglomerated spherical micelles, and had a final calcium phosphate concentration of up to 15 wt%. Analysis with x-ray diffraction and NMR indicated a disordered brushite phase with the phosphate groups linking inorganic phase to the polymer.

  2. Encapsulation of plasmid DNA in calcium phosphate nanoparticles: stem cell uptake and gene transfer efficiency

    Directory of Open Access Journals (Sweden)

    Cao X

    2011-12-01

    Full Text Available Xia Cao*, Wenwen Deng*, Yuan Wei*, Weiyan Su, Yan Yang, Yawei Wei, Jiangnan Yu, Ximing XuDepartment of Pharmaceutics, School of Pharmacy, and Center for Nano Drug/Gene Delivery and Tissue Engineering, Jiangsu University, Jingkou District, Zhenjiang, People's Republic of China*These authors contributed equally to this workBackground: The purpose of this study was to develop calcium phosphate nanocomposite particles encapsulating plasmid DNA (CP-pDNA nanoparticles as a nonviral vector for gene delivery.Methods: CP-pDNA nanoparticles employing plasmid transforming growth factor beta 1 (TGF-β1 were prepared and characterized. The transfection efficiency and cell viability of the CP-pDNA nanoparticles were evaluated in mesenchymal stem cells, which were identified by immunofluorescence staining. Cytotoxicity of plasmid TGF-β1 and calcium phosphate to mesenchymal stem cells were evaluated by MTT assay.Results: The integrity of TGF-β1 encapsulated in the CP-pDNA nanoparticles was maintained. The well dispersed CP-pDNA nanoparticles exhibited an ultralow particle size (20–50 nm and significantly lower cytotoxicity than Lipofectamine™ 2000. Immunofluorescence staining revealed that the cultured cells in this study were probably mesenchymal stem cells. The cellular uptake and transfection efficiency of the CP-pDNA nanoparticles into the mesenchymal stem cells were higher than that of needle-like calcium phosphate nanoparticles and a standard calcium phosphate transfection kit. Furthermore, live cell imaging and confocal laser microscopy vividly showed the transportation process of the CP-pDNA nanoparticles in mesenchymal stem cells. The results of a cytotoxicity assay found that both plasmid TGF-β1 and calcium phosphate were not toxic to mesenchymal stem cells.Conclusion: CP-pDNA nanoparticles can be developed into an effective alternative as a nonviral gene delivery system that is highly efficient and has low cytotoxicity.Keywords: calcium

  3. Pathogenic role of basic calcium phosphate crystals in destructive arthropathies

    NARCIS (Netherlands)

    Ea, H.K.; Chobaz, V.; Nguyen, C.; Nasi, S.; Lent, P.L. van; Daudon, M.; Dessombz, A.; Bazin, D.; McCarthy, G.; Jolles-Haeberli, B.; Ives, A.; Linthoudt, D. Van; So, A.; Liote, F.; Busso, N.

    2013-01-01

    BACKGROUND: basic calcium phosphate (BCP) crystals are commonly found in osteoarthritis (OA) and are associated with cartilage destruction. BCP crystals induce in vitro catabolic responses with the production of metalloproteases and inflammatory cytokines such as interleukin-1 (IL-1). In vivo, IL-1

  4. Injectable calcium phosphate cement for bone repair and implant fixation.

    NARCIS (Netherlands)

    Jansen, J.; Ooms, E.M.; Verdonschot, N.J.J.; Wolke, J.G.C.

    2005-01-01

    The studies as described are aimed at determining the efficacy of newly developed calcium phosphate cement when this material is used as a bone defect filler or gap filler around metal implants. An overview is provided about bone graft substitutes and methods of metal implant fixation.

  5. Calcium phosphate implants coatings as carriers for BMP-2

    NARCIS (Netherlands)

    Liu, Y.; He, J.F.; Hunziker, E.B.

    2009-01-01

    The osteoconductivity of dental implants can be improved by coating them with a layer of calcium phosphate (CaP), which can be rendered osteoinductive by functionalizing it with an osteogenic agent, such as bone morphogenetic protein 2 (BMP-2). In the present study, we wished to compare the osteoind

  6. Osteoinduction of calcium phosphate biomaterials in small animals

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Lijia; Shi, Yujun [Key Laboratory of Transplant Engineering and Immunology, Ministry of Health, West China Hospital, Sichuan University, Chengdu (China); Ye, Feng [Department of Pathology, West China Hospital, Sichuan University, Chengdu, 610041 (China); Bu, Hong, E-mail: hongbu@scu.edu.cn [Key Laboratory of Transplant Engineering and Immunology, Ministry of Health, West China Hospital, Sichuan University, Chengdu (China); Department of Pathology, West China Hospital, Sichuan University, Chengdu, 610041 (China)

    2013-04-01

    Although osteoinduction mechanism of calcium phosphate (CP) ceramics is still unclear, several essential properties have been reported, such as chemical composition, pore size and porosity, etc. In this study, calcium phosphate powder (Ca{sub 3}(PO{sub 4}){sub 2}, CaP, group 1), biphasic calcium phosphate ceramic powder (BCP, group 2), and intact BCP rods (group 3) were implanted into leg muscles of mice and dorsal muscles of rabbits. One month and three months after implantation, samples were harvested for biological and histological analysis. New bone tissues were observed in 10/10 samples in group 1, 3/10 samples in group 2, and 9/10 samples in group 3 at 3rd month in mice, but not in rabbits. In vitro, human mesenchymal stem cells (hMSCs) were cultured with trace CaP and BCP powder, and osteogenic differentiation was observed at day 7. Our results suggested that chemical composition is the prerequisite in osteoinduction, and pore structure would contribute to more bone formation. - Highlights: ► Intrinsic osteoinduction of calcium phosphate biomaterials was observed implanted in muscles of mice. ► Biomaterials powder also has osteoinduction property. ► Osteogenic genes and protein could be detected by RT-PCR and Western blot in implanted biomaterials. ► Osteogenic phenomenon could be observed by electron microscopy. ► The chemical composition is the prerequisite in osteoinduction, and pore structure would contribute to more bone formation.

  7. In vivo bone response to porous calcium phosphate cement.

    NARCIS (Netherlands)

    Real, R.P. del; Ooms, E.M.; Wolke, J.G.C.; Vallet-Regi, M.; Jansen, J.A.

    2003-01-01

    We conducted an in vivo experiment to evaluate the resorption rate of a calcium phosphate cement (CPC) with macropores larger than 100 microm, using the CPC called Biocement D (Merck Biomaterial, Darmstadt, Germany), which after setting only shows pores smaller than 1 microm. The gas bubble method u

  8. Mechanical properties of porous, electrosprayed calcium phosphate coatings

    NARCIS (Netherlands)

    Leeuwenburgh, S.C.G.; Wolke, J.G.C.; Lommen, L.; Pooters, T.; Schoonman, J.; Jansen, J.A.

    2006-01-01

    Mechanical properties of calcium phosphate coatings (CaP), deposited using the electrostatic spray deposition (ESD) technique, have been characterized using a range of analytical techniques, including tensile testing (ASTM C633), fatigue testing (ASTM E855), and scratch testing using blunt and sharp

  9. Optimizing conditions for calcium phosphate mediated transient transfection

    Directory of Open Access Journals (Sweden)

    Ling Guo

    2017-03-01

    Conclusions: Calcium phosphate mediated transfection is the most low-cost approach to introduce recombinant DNA into culture cells. However, the utility of this procedure is limited in highly-differentiated cells. Here we describe the specific HBS-buffered saline, PH, glycerol shock, vortex strength, transfection medium, and particle concentrations conditions necessary to optimize this transfection method in highly differentiated cells.

  10. Biomimetic calcium phosphate coatings on recombinant spider silk fibres

    Energy Technology Data Exchange (ETDEWEB)

    Yang Liang; Habibovic, Pamela; Van Blitterswijk, Clemens A [Department of Tissue Regeneration, University of Twente, PO Box 217, 7500 AE Enschede (Netherlands); Hedhammar, My; Johansson, Jan [Department of Anatomy, Physiology and Biochemistry, Swedish University of Agricultural Sciences, the Biomedical Centre, Box 575, 751 23 Uppsala (Sweden); Blom, Tobias; Leifer, Klaus [Department of Engineering Sciences, Uppsala University, Box 534, S-751 21 Uppsala (Sweden)

    2010-08-01

    Calcium phosphate ceramic coatings, applied on surfaces of metallic and polymeric biomaterials, can improve their performance in bone repair and regeneration. Spider silk is biocompatible, strong and elastic, and hence an attractive biomaterial for applications in connective tissue repair. Recently, artificial spider silk, with mechanical and structural characteristics similar to those of native spider silk, has been produced from recombinant minispidroins. In the present study, supersaturated simulated body fluid was used to deposit calcium phosphate coatings on recombinant spider silk fibres. The mineralization process was followed in time using scanning electron microscopy equipped with an energy dispersive x-ray (EDX) detector and Raman spectroscope. Focused ion beam technology was used to produce a cross section of a coated fibre, which was further analysed by EDX. Preliminary in vitro experiments using a culture of bone marrow-derived human mesenchymal stem cells (hMSCs) on coated fibres were also performed. This study showed that recombinant spider silk fibres were successfully coated with a homogeneous and thick crystalline calcium phosphate layer. In the course of the mineralization process from modified simulated body fluid, sodium chloride crystals were first deposited on the silk surface, followed by the deposition of a calcium phosphate layer. The coated silk fibres supported the attachment and growth of hMSCs.

  11. Microporous calcium phosphate ceramics driving osteogenesis through surface architecture

    NARCIS (Netherlands)

    Zhang, J.; Barbieri, D.; Hoopen, ten H.W.M.; Bruijn, de J.D.; Blitterswijk, van C.A.; Yuan, H.

    2015-01-01

    The presence of micropores in calcium phosphate (CaP) ceramics has shown its important role in initiating inductive bone formation in ectopic sites. To investigate how microporous CaP ceramics trigger osteoinduction, we optimized two biphasic CaP ceramics (i.e., BCP-R and BCP-S) to have the same che

  12. Atomic structure of intracellular amorphous calcium phosphate deposits.

    Science.gov (United States)

    Betts, F; Blumenthal, N C; Posner, A S; Becker, G L; Lehninger, A L

    1975-06-01

    The radial distribution function calculated from x-ray diffraction of mineralized cytoplasmic structures isolated from the hepatopancreas of the blue crab (Callinectes sapidus) is very similar to that previously found for synthetic amorphous calcium phosphate. Both types of mineral apparently have only short-range atomic order, represented as a neutral ion cluster of about 10 A in longest dimension, whose probable composition is expressed by the formula Ca9(PO4)6. The minor differences observed are attributed to the presence in the biological mineral of significant amounts of Mg-2+ and ATP. Synthetic amorphous calcium phosphate in contact with a solution containing an amount of ATP equivalent to that of the biological mineral failed to undergo conversion to the thermodynamically more stable hydroxyapatite. The amorphous calcium phosphate of the cytoplasmic mineral granules is similarly stable, and does not undergo conversion to hydroxyapatite, presumably owing to the presence of ATP and Mg-2+, known in inhibitors of the conversion process. The physiological implications of mineral deposits consisting of stabilized calcium phosphate ion clusters are discussed.

  13. Amorphous calcium phosphate and its application in dentistry

    Directory of Open Access Journals (Sweden)

    Sun Wei-bin

    2011-07-01

    Full Text Available Abstract Amorphous Calcium Phosphate (ACP is an essential mineral phase formed in mineralized tissues and the first commercial product as artificial hydroxyapatite. ACP is unique among all forms of calcium phosphates in that it lacks long-range, periodic atomic scale order of crystalline calcium phosphates. The X-ray diffraction pattern is broad and diffuse with a maximum at 25 degree 2 theta, and no other different features compared with well-crystallized hydroxyapatite. Under electron microscopy, its morphological form is shown as small spheroidal particles in the scale of tenths nanometer. In aqueous media, ACP is easily transformed into crystalline phases such as octacalcium phosphate and apatite due to the growing of microcrystalline. It has been demonstrated that ACP has better osteoconductivity and biodegradability than tricalcium phosphate and hydroxyapatite in vivo. Moreover, it can increase alkaline phosphatase activities of mesoblasts, enhance cell proliferation and promote cell adhesion. The unique role of ACP during the formation of mineralized tissues makes it a promising candidate material for tissue repair and regeneration. ACP may also be a potential remineralizing agent in dental applications. Recently developed ACP-filled bioactive composites are believed to be effective anti-demineralizing/remineralizing agents for the preservation and repair of tooth structures. This review provides an overview of the development, structure, chemical composition, morphological characterization, phase transformation and biomedical application of ACP in dentistry.

  14. Porosity prediction of calcium phosphate cements based on chemical composition.

    Science.gov (United States)

    Öhman, Caroline; Unosson, Johanna; Carlsson, Elin; Ginebra, Maria Pau; Persson, Cecilia; Engqvist, Håkan

    2015-07-01

    The porosity of calcium phosphate cements has an impact on several important parameters, such as strength, resorbability and bioactivity. A model to predict the porosity for biomedical cements would hence be a useful tool. At the moment such a model only exists for Portland cements. The aim of this study was to develop and validate a first porosity prediction model for calcium phosphate cements. On the basis of chemical reaction, molar weight and density of components, a volume-based model was developed and validated using calcium phosphate cement as model material. 60 mol% β-tricalcium phosphate and 40 mol% monocalcium phosphate monohydrate were mixed with deionized water, at different liquid-to-powder ratios. Samples were set for 24 h at 37°C and 100% relative humidity. Thereafter, samples were dried either under vacuum at room temperature for 24 h or in air at 37 °C for 7 days. Porosity and phase composition were determined. It was found that the two drying protocols led to the formation of brushite and monetite, respectively. The model was found to predict well the experimental values and also data reported in the literature for apatite cements, as deduced from the small absolute average residual errors (brushite, monetite and apatite cements. The model gives a good estimate of the final porosity and has the potential to be used as a porosity prediction tool in the biomedical cement field.

  15. Biologically Analogous Calcium Phosphate Tubes from a Chemical Garden.

    Science.gov (United States)

    Hughes, Erik A B; Williams, Richard L; Cox, Sophie C; Grover, Liam M

    2017-02-28

    Calcium phosphate (CaPO4) tubes with features comparable to mineralized biological microstructures, such as Haversian canals, were grown from a calcium gel/phosphate solution chemical garden system. A significant difference in gel mass in response to high and low solute phosphate equivalent environments existed within 30 min of solution layering upon gel (p = 0.0067), suggesting that the nature of advective movement between gel and solution is dependent on the solution concentration. The transport of calcium cations (Ca(2+)) and phosphate anions (PO4(3-)) was quantified and changes in pH were monitored to explain the preferential formation of tubes within a PO4(3-) concentration range of 0.5-1.25 M. Ingress from the anionic solution phase into the gel followed by the liberation of Ca(2+) ions from the gel was found to be essential for acquiring self-assembled tubular CaPO4 structures. Tube analysis by scanning electron microscopy (SEM), X-ray diffraction (XRD), and micro X-ray florescence (μ-XRF) revealed hydroxyapatite (HA, Ca10(PO4)6(OH)2) and dicalcium phosphate dihydrate (DCPD, CaHPO4·2H2O) phases organized in a hierarchical manner. Notably, the tubule diameters ranged from 100 to 150 μm, an ideal size for the permeation of vasculature in biological hard tissue.

  16. Calcium-phosphate-osteopontin particles for caries control

    DEFF Research Database (Denmark)

    Schlafer, Sebastian

    Oftentimes caries lesions develop in protected sites that are difficult to access by self-performed mechanical tooth cleaning. At present, there is a growing interest in chemical adjuncts to mechanical procedures of oral hygiene that aim at biofilm control rather than biofilm eradication. Calcium......-phosphate-osteopontin particles are a new promising therapeutic approach to caries control. They are designed to bind to dental biofilms and interfere with biofilm build-up, lowering the bacterial burden on the tooth surface without affecting bacterial viability in the oral cavity. Moreover, they dissolve when pH in the biofilm...... drops to 6 or below and release buffering phosphate ions that stabilize biofilm pH above the critical level for enamel dissolution. With that twofold approach, calcium-phosphate-osteopontin particles may make a relevant contribution to clinical caries control....

  17. Calcium-phosphate-osteopontin particles for caries control

    DEFF Research Database (Denmark)

    Schlafer, Sebastian; Birkedal, Henrik; Olsen, Jakob

    2016-01-01

    Caries is caused by acid production in biofilms on dental surfaces. Preventing caries therefore involves control of microorganisms and/or the acid produced. Here, calcium-phosphate-osteopontin particles are presented as a new approach to caries control. The particles are made by co......-precipitation and designed to bind to bacteria in biofilms, impede biofilm build-up without killing the microflora, and release phosphate ions to buffer bacterial acid production if the pH decreases below 6. Analysis of biofilm formation and pH in a five-species biofilm model for dental caries showed that treatment......H always remained above 5.5. Hence, calcium-phosphate-osteopontin particles show potential for applications in caries control....

  18. Characterization of calcium phosphate powders originating from Phyllacanthus imperialis and Trochidae Infundibulum concavus marine shells.

    Science.gov (United States)

    Tămăşan, M; Ozyegin, L S; Oktar, F N; Simon, V

    2013-07-01

    The study reports the preparation and characterization of powders consisting of the different phases of calcium phosphates that were obtained from the naturally derived raw materials of sea-shell origins reacted with H3PO4. Species of sea origin, such as corals and nacres, attracted a special interest in bone tissue engineering area. Nacre shells are built up of calcium carbonate in aragonite form crystallized in an organic matrix. In this work two natural marine origin materials (shells of echinoderm Sputnik sea urchin - Phyllacanthus imperialis and Trochidae Infundibulum concavus mollusk) were involved in the developing powders of calcium phosphate based biomaterials (as raw materials for bone-scaffolds) by hotplate and ultrasound methods. Thermal analyses of the as-prepared materials were made for an assessment of the thermal behavior and heat treatment temperatures. Samples from both sea shells each of them prepared by the above mentioned methods were subjected to thermal treatments at 450 °C and 850 °C in order to evaluate the crystalline transformations of the calcium phosphate structures in the heating process. By X-ray diffraction analyses various calcium phosphate phases were identified. In Sputnik sea urchins originated samples were found predominantly brushite and calcite as a small secondary phase, while in Trochidae I. concavus samples mainly monetite and HA phases were identified. Thermal treatment at 850 °C resulted flat-plate whitlockite crystals - β-MgTCP [(Ca, Mg)3 (PO4)2] for both samples regardless the preparation method (ultrasound or hotplate) or the targeted Ca/P molar ratio according with XRD patterns. Scanning electron microscopy and Fourier transformed infrared spectroscopy were involved more in the characterization of these materials and the good correlations of the results of these methods were made.

  19. Synthesis and characterization of powders calcium phosphate for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, D.M.P. de; Prants, W.T.; Camargo, N.H.A.; Gemelli, E., E-mail: daniellapinheiro@gmail.com, E-mail: w_prants@hotmail.com, E-mail: dem2nhac@joinville.udesc.br, E-mail: dma2ec@joinville.udesc.br [Universidade do Estado de Santa Catarina (UDESC), Joinville, SC (Brazil). Centro de Ciencias Tecnologicas

    2009-07-01

    Scientists of different areas research the bioceramics as new materials to substitute parts of the human body. The bioceramics of the calcium phosphate have the advantage present similar chemical composition to the structure of the bony apatite of the human skeleton. In this study, calcium phosphate powder was synthesized chemically using the solution of phosphorus pentoxide (P{sub 2}O{sub 5}) and calcium oxide (CaO) necessary for molar Ca/P =1.67. These works aim the study of different thermal treatments, physics and of the microstructure properties. For characterization the bony matrix were used the techniques of: X-ray diffraction (DRX); Scanning Electronic Microscopy (SEM) and Differential Scanning Calorimetry (DSC). (author)

  20. Fibre-reinforced calcium phosphate cements: a review.

    Science.gov (United States)

    Canal, C; Ginebra, M P

    2011-11-01

    Calcium phosphate cements (CPC) consist of one or more calcium orthophosphate powders, which upon mixing with water or an aqueous solution, form a paste that is able to set and harden after being implanted within the body. Different issues remain still to be improved in CPC, such as their mechanical properties to more closely mimic those of natural bone, or their macroporosity to favour osteointegration of the artificial grafts. To this end, blends of CPC with polymer and ceramic fibres in different forms have been investigated. The present work aims at providing an overview of the different approaches taken and identifying the most significant achievements in the field of fibre-reinforced calcium phosphate cements for clinical applications, with special focus on their mechanical properties.

  1. Incorporation of Collagen in Calcium Phosphate Cements for Controlling Osseointegration

    Directory of Open Access Journals (Sweden)

    Ming-Hsien Hu

    2017-08-01

    Full Text Available In this study, we investigated the effect of supplementing a non-dispersive dicalcium phosphate-rich calcium phosphate bone cement (DCP-rich CPC with type I collagen on in vitro cellular activities and its performance as a bone graft material. Varying amounts of type I collagen were added during the preparation of the DCP-rich CPC. In vitro cell adhesion, morphology, viability, and alkaline phosphatase (ALP activity were evaluated using progenitor bone cells. Bone graft performance was evaluated via a rat posterolateral lumbar fusion model and osteointegration of the implant. New bone formations in the restorative sites were assessed by micro-computed tomography (micro-CT and histological analysis. We found that the incorporation of collagen into the DCP-rich CPC was associated with increased cell adhesion, cell viability, and ALP activity in vitro. The spinal fusion model revealed a significant increase in bone regeneration. Additionally, better osseointegration was observed between the host bone and graft with the DCP-rich CPC supplemented with collagen than with the collagen-free DCP-rich CPC control graft. Furthermore, compared to the control graft, the results of micro-CT showed that a smaller amount of residual material was observed with the collagen-containing DCP-rich CPC graft compared with the control graft, which suggests the collagen supplement enhanced new bone formation. Of the different mixtures evaluated in this study (0.8 g DCP-rich CPC supplemented with 0.1, 0.2, and 0.4 mL type I collagen, respectively, DCP-rich CPC supplemented with 0.4 mL collagen led to the highest level of osteogenesis. Our results suggest that the DCP-rich CPC supplemented with collagen has potential to be used as an effective bone graft material in spinal surgery.

  2. A construction of novel iron-foam-based calcium phosphate/chitosan coating biodegradable scaffold material.

    Science.gov (United States)

    Wen, Zhaohui; Zhang, Liming; Chen, Chao; Liu, Yibo; Wu, Changjun; Dai, Changsong

    2013-04-01

    Slow corrosion rate and poor bioactivity restrict iron-based implants in biomedical application. In this study, we design a new iron-foam-based calcium phosphate/chitosan coating biodegradable composites offering a priority mechanical and bioactive property for bone tissue engineering through electrophoretic deposition (EPD) followed by a conversion process into a phosphate buffer solution (PBS). Tensile test results showed that the mechanical property of iron foam could be regulated through altering the construction of polyurethane foam. The priority coatings were deposited from 40% nano hydroxyapatite (nHA)/ethanol suspension mixed with 60% nHA/chitosan-acetic acid aqueous solution. In vitro immersion test showed that oxidation-iron foam as the matrix decreased the amount of iron implanted and had not influence on the bioactivity of this implant, obviously. So, this method could also be a promising method for the preparation of a new calcium phosphate/chitosan coating on foam construction.

  3. Conversion of Marine Structures to Calcium Phosphate Materials: Mechanisms of Conversion Using Two Different Phosphate Solutions

    OpenAIRE

    Macha, Innocent J.; Grossin, David; Ben-Nissan, Besim

    2016-01-01

    International audience; Marine structure, coralline materials were converted to calcium phosphate using twodifferent phosphate solutions. The aim was to study the conversion mechanisms under acidic andbasic environment at moderate conditions of temperature. Crystal growth and morphology ofconverted corals were characterized by XRD and SEM respectively. The results suggested thatunder acidic conditions (H3PO4), dissolution and precipitation control and direct the crystalformation and morpholog...

  4. In vivo behavior of a novel injectable calcium phosphate cement compared with two other commercially available calcium phosphate cements.

    NARCIS (Netherlands)

    Hannink, G.; Wolke, J.G.C.; Schreurs, B.W.; Buma, P.

    2008-01-01

    The aim of this study was to investigate the physicochemical and biological properties of a newly developed calcium phosphate cement (CPC). The novel cement was compared with two other commercially available CPCs. After mixing the powder and liquid phase, the CPCs were injected as a paste into a rab

  5. A novel biodegradable nicotinic acid/calcium phosphate composite coating on Mg-3Zn alloy

    Energy Technology Data Exchange (ETDEWEB)

    Song, Yingwei, E-mail: ywsong@imr.ac.cn; Shan, Dayong; Han, En-Hou

    2013-01-01

    A novel biodegradable composite coating is prepared to reduce the biodegradation rate of Mg-3Zn alloy. The Mg-3Zn substrate is first immersed into 0.02 mol L{sup -1} nicotinic acid (NA) solution, named as vitamin B{sub 3}, to obtain a pretreatment film, and then the electrodeposition of calcium phosphate coating with ultrasonic agitation is carried out on the NA pretreatment film to obtain a NA/calcium phosphate composite coating. Surface morphology is observed by scanning electron microscopy (SEM). Chemical composition is determined by X-ray diffraction (XRD) and EDX. Protection property of the coatings is evaluated by electrochemical tests. The biodegradable behavior is investigated by immersion tests. The results indicate that a thin but compact bottom layer can be obtained by NA pretreatment. The electrodeposition calcium phosphate coating consists of many flake particles and ultrasonic agitation can greatly improve the compactness of the coating. The composite coating is biodegradable and can reduce the biodegradation rate of Mg alloys in stimulated body fluid (SBF) for twenty times. The biodegradation process of the composite coating can be attributed to the gradual dissolution of the flake particles into chippings. - Highlights: Black-Right-Pointing-Pointer NA/calcium phosphate composite coating is prepared to protect Mg-3Zn alloy implant. Black-Right-Pointing-Pointer Nicotinic acid (vitamin B{sub 3}) is available to obtain a protective bottom film. Black-Right-Pointing-Pointer Ultrasonic agitation greatly improves the compactness of calcium phosphate coating. Black-Right-Pointing-Pointer The composite coating can reduce the biodegradation rate of Mg-3Zn twenty times. Black-Right-Pointing-Pointer The composite coating is biodegraded by the dissolution of flakes into chippings.

  6. Biomimetic Versus Sintered Calcium Phosphates: The In Vitro Behavior of Osteoblasts and Mesenchymal Stem Cells.

    Science.gov (United States)

    Sadowska, Joanna-Maria; Guillem-Marti, Jordi; Montufar, Edgar Benjamin; Espanol, Montserrat; Ginebra, Maria-Pau

    2017-02-21

    The fabrication of calcium phosphates using biomimetic routes, namely, precipitation processes at body temperature, results in distinct features compared to conventional sintered calcium phosphate ceramics, such as a high specific surface area (SSA) and micro- or nanometric crystal size. The aim of this article is to analyze the effects of these parameters on cell response, focusing on two bone cell types: rat mesenchymal stem cells (rMSCs) and human osteoblastic cells (SaOS-2). Biomimetic calcium-deficient hydroxyapatite (CDHA) was obtained by a low temperature setting reaction, and α-tricalcium phosphate (α-TCP) and β-tricalcium phosphate were subsequently obtained by sintering CDHA either at 1400°C or 1100°C. Sintered stoichiometric hydroxyapatite (HA) was also prepared using ceramic routes. The materials were characterized in terms of SSA, skeletal density, porosity, and pore size distribution. SaOS-2 cells and rMSCs were seeded either directly on the surfaces of the materials or on glass coverslips subsequently placed on top of the materials to expose the cells to the CaP-induced ionic changes in the culture medium, while avoiding any topography-related effects. CDHA produced higher ionic fluctuations in both cell culture media than sintered ceramics, with a strong decrease of calcium and a release of phosphate. Indirect contact cell cultures revealed that both cell types were sensitive to these ionic modifications, resulting in a decrease in proliferation rate, more marked for CDHA, this effect being more pronounced for rMSCs. In direct contact cultures, good cell adhesion was found on all materials, but, while cells were able to proliferate on the sintered calcium phosphates, cell number was significantly reduced with time on biomimetic CDHA, which was associated to a higher percentage of apoptotic cells. Direct contact of the cells with biomimetic CDHA resulted also in a higher alkaline phosphatase activity for both cell types compared to sintered Ca

  7. Cellular investigations on electrochemically deposited calcium phosphate composites.

    Science.gov (United States)

    Becker, Petra; Neumann, Hans-Georg; Nebe, Barbara; Lüthen, Frank; Rychly, Joachim

    2004-04-01

    Electrochemically deposited calcium phosphate (CaP) coatings are fast resorbable and existent only during the first period of osseointegration. In the present study, composite coatings with varying solubility (hydroxyapatite (HA), brushite with less HA and monetite (M) with less HA) were prepared and the influence of the degradation and the reprecipitation of CaP on osteoblastic cells were investigated. On the brushite composite coating a new precipitated, finely structured CaP phase was observed during immersion in cell culture medium with or without osteoblastic cells. The surface morphology of monetite and HA coatings were entirely unmodified under the same conditions. So it could be assumed that electrochemically deposited brushite with less HA acts as a precursor for new precipitated CaP. On this surface osteoblastic cells revealed a well-spread morphology with pronounced actin cytoskeleton and demonstrated good proliferation behaviour. Thus we suggest that brushite seems to be especially suitable for coating of implants as a matrix for nucleation and growth of new bone.

  8. Degree of vinyl conversion in experimental amorphous calcium phosphate composites

    Science.gov (United States)

    Tarle, Z.; Knežević, A.; Matošević, D.; Škrtić, D.; Ristić, M.; Prskalo, K.; Musić, S.

    2009-04-01

    An experimental dental composite, based on amorphous calcium phosphate (ACP) with the potential to arrest caries development and regenerate mineral-deficient tooth structures has recently been developed. The aim of this study was to assess the degree of vinyl conversion (DVC) attained in experimental composites based on zirconia-modified ACP. Photo-activated resins were based on ethoxylated bisphenol A dimethacrylate (EBPADMA) [ETHM series with varying EBPADMA/triethylene glycol dimethacrylate (TEGDMA) molar ratios assigned 0.5-ETHM I, 0.85-ETHM II and 1.35-ETHM III], or 2,2-bis[p-(2'-hydroxy-3'-methacryloxypropoxy)phenyl]-propane (Bis-GMA) [BTHZ series]. To asses a possible effect of filler particle size on DVC, composites containing 60 mass % resin and 40 mass % of either milled ACP (mACP; median diameter d m = 0.9 μm) or coarse ACP (cACP; d m = 6.0 μm) were prepared, and irradiated with LED curing unit for 40 s. The DVC was calculated as the % change in the ratio of the integrated peak areas between the aliphatic and aromatic absorption bands determined by Fourier transform infrared spectroscopy (FTIR). The highest DVCs values were attained in mACP-BTHZ, cACP-BTHZ and mACP-ETHM III formulations. DVC of tested ACP composites (on average (76.76 ± 4.43)%) compares well with or exceeds DVCs values reported for the majority of commercial materials.

  9. Influence of calcium on ceramide-1-phosphate monolayers

    Directory of Open Access Journals (Sweden)

    Joana S. L. Oliveira

    2016-02-01

    Full Text Available Ceramide-1-phosphate (C1P plays an important role in several biological processes, being identified as a key regulator of many protein functions. For instance, it acts as a mediator of inflammatory responses. The mediation of the inflammation process happens due to the interaction of C1P with the C2 domain of cPLA2α, an effector protein that needs the presence of submicromolar concentrations of calcium ions. The aim of this study was to determine the phase behaviour and structural properties of C1P in the presence and absence of millimolar quantities of calcium in a well-defined pH environment. For that purpose, we used monomolecular films of C1P at the soft air/liquid interface with calcium ions in the subphase. The pH was varied to change the protonation degree of the C1P head group. We used surface pressure versus molecular area isotherms coupled with other monolayer techniques as Brewster angle microscopy (BAM, infrared reflection–absorption spectroscopy (IRRAS and grazing incidence X-ray diffraction (GIXD. The isotherms indicate that C1P monolayers are in a condensed state in the presence of calcium ions, regardless of the pH. At higher pH without calcium ions, the monolayer is in a liquid-expanded state due to repulsion between the negatively charged phosphate groups of the C1P molecules. When divalent calcium ions are added, they are able to bridge the highly charged phosphate groups, enhancing the regular arrangement of the head groups. Similar solidification of the monolayer structure can be seen in the presence of a 150 times larger concentration of monovalent sodium ions. Therefore, calcium ions have clearly a strong affinity for the phosphomonoester of C1P.

  10. The determination of calcium in phosphate, carbonate, and silicate rocks by flame photometer

    Science.gov (United States)

    Kramer, Henry

    1956-01-01

    A method has been developed for the determination of calcium in phosphate, carbonate, and silicate rocks using the Beckman flame photometer, with photomultiplier attachement. The sample is dissolved in hydrofluoric, nitric, and perchloric acids, the hydrofluoric and nitric acids are expelled, a radiation buffer consisting of aluminum, magnesium, iron, sodium, potassium, phosphoric acid, and nitric acid is added, and the solution is atomized in an oxy-hydrogen flame with an instrument setting of 554 mµ. Measurements are made by comparison against calcium standards, prepared in the same manner, in the 0 to 50 ppm range. The suppression of calcium emission by aluminum and phosphate was overcome by the addition of a large excess of magnesium. This addition almost completely restores the standard curve obtained from a solution of calcium nitrate. Interference was noted when the iron concentration in the aspirated solution (including the iron from the buffer) exceeded 100 ppm iron. Other common rock-forming elements did not interfere. The results obtained by this procedure are within ± 2 percent of the calcium oxide values obtained by other methods in the range 1 to 95 percent calcium oxide. In the 0 to 1 percent calcium oxide range the method compares favorably with standard methods.

  11. Physicochemical and Microstructural Characterization of Injectable Load-Bearing Calcium Phosphate Scaffold

    Directory of Open Access Journals (Sweden)

    Mazen Alshaaer

    2013-01-01

    Full Text Available Injectable load-bearing calcium phosphate scaffolds are synthesized using rod-like mannitol grains as porogen. These degradable injectable strong porous scaffolds, prepared by calcium phosphate cement, could represent a valid solution to achieve adequate porosity requirements while providing adequate support in load-bearing applications. The proposed process for preparing porous injectable scaffolds is as quick and versatile as conventional technologies. Using this method, porous CDHA-based calcium phosphate scaffolds with macropores sizes ranging from 70 to 300 μm, micropores ranging from 5 to 30 μm, and 30% open macroporosity were prepared. The setting time of the prepared scaffolds was 15 minutes. Also their compressive strength and e-modulus, 4.9 MPa and 400 MPa, respectively, were comparable with those of the cancellous bone. Finally, the bioactivity of the scaffolds was confirmed by cell growth with cytoplasmic extensions in the scaffolds in culture, demonstrating that the scaffold has a potential for MSC seeding and growth architecture. This combination of an interconnected macroporous structure with pore size suitable for the promotion of cell seeding and proliferation, plus adequate mechanical features, represents a porous scaffold which is a promising candidate for bone tissue engineering.

  12. Diagnosis and clinical manifestations of calcium pyrophosphate and basic calcium phosphate crystal deposition diseases.

    Science.gov (United States)

    Ea, Hang-Korng; Lioté, Frédéric

    2014-05-01

    Basic calcium phosphate and pyrophosphate calcium crystals are the 2 main calcium-containing crystals that can deposit in all skeletal tissues. These calcium crystals give rise to numerous manifestations, including acute inflammatory attacks that can mimic alarming and threatening differential diagnoses, osteoarthritis-like lesions, destructive arthropathies, and calcific tendinitis. Awareness of uncommon localizations and manifestations such as intraspinal deposition (eg, crowned dens syndrome, tendinitis of longus colli muscle, massive cervical myelopathy compression) prevents inappropriate procedures and cares. Coupling plain radiography, ultrasonography, computed tomography, and synovial fluid analysis allow accurate diagnosis by directly or indirectly identifying the GRAAL of microcrystal-related symptoms.

  13. Injectable thermosensitive hydrogel composite with surface-functionalized calcium phosphate as raw materials

    Directory of Open Access Journals (Sweden)

    Fan RR

    2014-01-01

    Full Text Available RangRang Fan,1 XiaoHui Deng,2 LiangXue Zhou,1 Xiang Gao,1 Min Fan,1 YueLong Wang,1 Gang Guo11State Key Laboratory of Biotherapy and Cancer Center, Department of Neurosurgery, West China Hospital, West China Medical School, Sichuan University, Chengdu, 2Department of Human Anatomy, Xinxiang Medical University, Xinxiang, People's Republic of ChinaAbstract: In this study, L-lactide was used to modify the tricalcium phosphate (β-TCP and tetracalcium phosphate (TTCP surface which can form functionalized poly(l-lactic acid (PLLA-grafted β-TCP (g-β-TCP and PLLA-grafted TTCP (g-TTCP particles. The g-β-TCP and g-TTCP obtained were incorporated into a PEG-PCL-PEG (PECE matrix to prepare injectable thermosensitive hydrogel composites. The morphology of the hydrogel composites showed that the g-β-TCP and g-TTCP particles dispersed homogeneously into the polymer matrix, and each hydrogel composite had a three-dimensional network structure. Rheologic analysis showed that the composite had good thermosensitivity. Changes in calcium concentration and pH in simulated body fluid solutions confirmed the feasibility of surface-functionalized calcium phosphate for controlled release of calcium. All the results indicate that g-β-TCP/PECE and g-TTCP/PECE hydrogels might be a promising protocol for tissue engineering.Keywords: injectable, thermosensitivity, surface functionalization, calcium phosphate, biocompatibility

  14. Effect of different calcium phosphate scaffold ratios on odontogenic differentiation of human dental pulp cells.

    Science.gov (United States)

    AbdulQader, Sarah Talib; Kannan, Thirumulu Ponnuraj; Rahman, Ismail Ab; Ismail, Hanafi; Mahmood, Zuliani

    2015-04-01

    Calcium phosphate (CaP) scaffolds have been widely and successfully used with osteoblast cells for bone tissue regeneration. However, it is necessary to investigate the effects of these scaffolds on odontoblast cells' proliferation and differentiation for dentin tissue regeneration. In this study, three different hydroxyapatite (HA) to beta tricalcium phosphate (β-TCP) ratios of biphasic calcium phosphate (BCP) scaffolds, BCP20, BCP50, and BCP80, with a mean pore size of 300μm and 65% porosity were prepared from phosphoric acid (H2PO4) and calcium carbonate (CaCO3) sintered at 1000°C for 2h. The extracts of these scaffolds were assessed with regard to cell viability and differentiation of odontoblasts. The high alkalinity, more calcium, and phosphate ions released that were exhibited by BCP20 decreased the viability of human dental pulp cells (HDPCs) as compared to BCP50 and BCP80. However, the cells cultured with BCP20 extract expressed high alkaline phosphatase activity and high expression level of bone sialoprotein (BSP), dental matrix protein-1 (DMP-1), and dentin sialophosphoprotein (DSPP) genes as compared to that cultured with BCP50 and BCP80 extracts. The results highlighted the effect of different scaffold ratios on the cell microenvironment and demonstrated that BCP20 scaffold can support HDPC differentiation for dentin tissue regeneration. Copyright © 2014 Elsevier B.V. All rights reserved.

  15. Hybrid Calcium Phosphate Coatings for Titanium Implants

    Science.gov (United States)

    Kharapudchenko, E.; Ignatov, V.; Ivanov, V.; Tverdokhlebov, S.

    2017-01-01

    Hybrid multilayer coatings were obtained on titanium substrates by the combination of two methods: the micro-arc oxidation in phosphoric acid solution with the addition of calcium compounds to high supersaturated state and RF magnetron sputtering of the target made of synthetic hydroxyapatite. 16 different groups of coatings were formed on titanium substrates and in vitro studies were conducted in accordance with ISO 23317 in the solution simulating body fluid. The studies using SEM, XRD of the coatings of the samples before and after exposure to SBF were performed. The features of morphology, chemical and phase composition of the studied coatings are shown.

  16. Calcium phosphate nucleation on surface-modified PTFE membranes.

    Science.gov (United States)

    Grøndahl, Lisbeth; Cardona, Francisco; Chiem, Khang; Wentrup-Byrne, Edeline; Bostrom, Thor

    2003-06-01

    Highly porous PTFE membranes are currently being used in facial reconstructive surgery. The present study aims at improving this biomaterial through creating a more bioactive surface by introducing ionic groups onto the surface. The unmodified PTFE membrane does not induce inorganic growth after immersion in simulated body fluid (SBF) for up to 4 weeks. Copolymeric grafting with acrylic acid (AAc) by means of gamma irradiation and subsequent in vitro testing in SBF reveals that this copolymer initially acts as an ion-exchange material and subsequently induces growth of a calcium phosphate phase (Ca/P=2.7) when large amounts (15%) of pAAc are introduced onto the membrane surface. This copolymer is not expected to function well from a biomaterials perspective since SEM showed the pores on the surface to be partly blocked. In contrast, the surface of monoacryloxyethyl phosphate (MAEP)-modified samples is altered at a molecular level only. Yet the modified materials are able to induce calcium phosphate nucleation when the external surface coverage is 44% or above. The initial inorganic growth on these membranes in SBF has a (Ca+Mg)/P ratio of 1.1 (presumably Brushite or Monetite). The secondary growth, possibly calcium-deficient apatite or tricalcium phosphate, has a (Ca+Mg)/P ratio of 1.5. This result is a promising indicator of a bioactive biomaterial.

  17. The role of intracellular calcium phosphate in osteoblast-mediated bone apatite formation.

    Science.gov (United States)

    Boonrungsiman, Suwimon; Gentleman, Eileen; Carzaniga, Raffaella; Evans, Nicholas D; McComb, David W; Porter, Alexandra E; Stevens, Molly M

    2012-08-28

    Mineralization is a ubiquitous process in the animal kingdom and is fundamental to human development and health. Dysfunctional or aberrant mineralization leads to a variety of medical problems, and so an understanding of these processes is essential to their mitigation. Osteoblasts create the nano-composite structure of bone by secreting a collagenous extracellular matrix (ECM) on which apatite crystals subsequently form. However, despite their requisite function in building bone and decades of observations describing intracellular calcium phosphate, the precise role osteoblasts play in mediating bone apatite formation remains largely unknown. To better understand the relationship between intracellular and extracellular mineralization, we combined a sample-preparation method that simultaneously preserved mineral, ions, and ECM with nano-analytical electron microscopy techniques to examine osteoblasts in an in vitro model of bone formation. We identified calcium phosphate both within osteoblast mitochondrial granules and intracellular vesicles that transported material to the ECM. Moreover, we observed calcium-containing vesicles conjoining mitochondria, which also contained calcium, suggesting a storage and transport mechanism. Our observations further highlight the important relationship between intracellular calcium phosphate in osteoblasts and their role in mineralizing the ECM. These observations may have important implications in deciphering both how normal bone forms and in understanding pathological mineralization.

  18. Biomimetic synthesis of modified calcium phosphate fine powders and their in vitro studies

    Science.gov (United States)

    Gergulova, R.; Tepavitcharova, S.; Rabadjieva, D.; Sezanova, K.; Ilieva, R.; Alexandrova, R.; Andonova-Lilova, B.

    2013-12-01

    Biomimetic approach and subsequent high-temperature treatment were used to synthesize ion modified calcium phosphate fine powders. Thus, using Simulated Body Fluid (SBF) as an ion modifier, a bi-phase mixture of ion modified β-tricalcium phosphate and hydroxyapatite (β-TCP + HA) was prepared. The use of SBF electrolyte solution enriched with Mg2+ or Zn2+ yielded monophase β-tricalcium phosphate additionally modified with Mg2+ or Zn2+ (Mg-β-TCP or Zn-β-TCP). The in vitro behavior of the prepared powders on cell viability and proliferation of murine BALB/c 3T3 fibroblasts and of human Lep 3 cells was studied by MTT test assays and Mosmann method after 72 h incubation. The relative cell viability was calculated.

  19. Biomimetic synthesis of modified calcium phosphate fine powders and their in vitro studies

    Energy Technology Data Exchange (ETDEWEB)

    Gergulova, R., E-mail: rumigg@yahoo.com; Tepavitcharova, S., E-mail: rumigg@yahoo.com; Rabadjieva, D., E-mail: rumigg@yahoo.com; Sezanova, K., E-mail: rumigg@yahoo.com; Ilieva, R., E-mail: rumigg@yahoo.com [Institute of General and Inorganic Chemistry, Bulgarian Academy of Sciences, Acad. G. Bonchev Str., Bl. 11, 1113 Sofia (Bulgaria); Alexandrova, R.; Andonova-Lilova, B. [Institute of Experimental Morphology, Pathology and Anthropology with Museum, BAS, Acad. G. Bonchev Str., Bl. 25, Sofia (Bulgaria)

    2013-12-16

    Biomimetic approach and subsequent high-temperature treatment were used to synthesize ion modified calcium phosphate fine powders. Thus, using Simulated Body Fluid (SBF) as an ion modifier, a bi-phase mixture of ion modified β-tricalcium phosphate and hydroxyapatite (β-TCP + HA) was prepared. The use of SBF electrolyte solution enriched with Mg{sup 2+} or Zn{sup 2+} yielded monophase β-tricalcium phosphate additionally modified with Mg{sup 2+} or Zn{sup 2+} (Mg-β-TCP or Zn-β-TCP). The in vitro behavior of the prepared powders on cell viability and proliferation of murine BALB/c 3T3 fibroblasts and of human Lep 3 cells was studied by MTT test assays and Mosmann method after 72 h incubation. The relative cell viability was calculated.

  20. Kinetic study of the setting reaction of a calcium phosphate bone cement.

    Science.gov (United States)

    Fernández, E; Ginebra, M P; Boltong, M G; Driessens, F C; Ginebra, J; De Maeyer, E A; Verbeeck, R M; Planell, J A

    1996-11-01

    The setting reaction of a calcium phosphate bone cement consisting of a mixture of 63.2 wt % alpha-tertiary calcium phosphate (TCP)[alpha-Ca3(PO4)2], 27.7 wt % dicalcium phosphate (DCP) (CaHPO4), and 9.1 wt % of precipitated hydroxyapatite [(PHA) used as seed material] was investigated. The cement samples were prepared at a liquid-to-powder ratio of: L/P = 0.30 ml/g. Bi-distilled water was used as liquid solution. After mixing the powder and liquid, some samples were molded and aged in Ringer's solution at 37 degrees C. At fixed time intervals they were unmolded and then immediately frozen in liquid nitrogen at a temperature of TN = -196 degrees C, lyofilized, and examined by X-ray diffraction as powder samples. The compressive strength versus time was also measured in setting samples of this calcium phosphate bone cement. The crystal entanglement morphology was examined by scanning electron microscopy. The results showed that: 1) alpha-TCP reacted to a calcium-deficient hydroxyapatite (CDHA), Ca9(HPO4)(PO4)5O H, whereas DCP did not react significantly; 2) the reaction was nearly finished within 32 h, during which both the reaction percentage and the compressive strength increased versus time, with a strong correlation between them; and 3) the calcium phosphate bone cement showed in general a structure of groups of interconnected large plates distributed among agglomerations of small crystal plates arranged in very dense packings.

  1. Effect of carbon fiber on calcium phosphate bone cement

    Institute of Scientific and Technical Information of China (English)

    戴红莲; 王欣宇; 黄健; 闫玉华; 李世普

    2004-01-01

    The calcium phosphate cement (α-TCP/TTCP) was reinforced with oxidation-treated carbon fibers. The effect of aspect ratio and content of carbon fiber on the compression strength and bending strength of the hardened body was discussed. The results show that the reinforcing effect is optimal as the aspect ratio is 375 and the additive amount is 0.3% (mass fraction). Under this condition, the compressive strength is increased by 55% (maximum 63.46 MPa), and the bending strength is nearly increased by 100% (maximum 11.95 MPa), respectively. However, if the additive quantity and aspect ratio are too high, the effect of the carbon fibers is limited because it can not be dispersed uniformly in the hardened body. The biological evaluation indicates that the calcium phosphate cement reinforced by carbon fibers has good biocompatibility.

  2. Calcium Phosphate Coating over Silk Fibroin Film by Biomimetic Methods

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    To investigate the biomineralization behavior of silk fibroin and to valuate the biodegradation and biocompatibility of the hybrid biomaterial, the calcium phosphate deposits were identified with SEM, EDX,XRD and FTIR. The results reveal that supersaturated calcification solution is an effective method for the mineralization of fibroin film. Enzymatic degradation experiment demonstrates the biodegradability of the composites. Osteoblasts incubation shows an excellent cytocompatibility on the mineralized fibroin films.

  3. Aggregation of Calcium Phosphate and Oxalate Phases in the Formation of Renal Stones

    OpenAIRE

    2014-01-01

    The majority of human kidney stones are comprised of multiple calcium oxalate monohydrate (COM) crystals encasing a calcium phosphate nucleus. The physiochemical mechanism of nephrolithiasis has not been well determined on the molecular level; this is crucial to the control and prevention of renal stone formation. This work investigates the role of phosphate ions on the formation of calcium oxalate stones; recent work has identified amorphous calcium phosphate (ACP) as a rapidly forming initi...

  4. Single Step Sintered Calcium Phosphate Fibers from Avian EGG Shell

    Science.gov (United States)

    Dadhich, Prabhash; Das, Bodhisatwa; Dhara, Santanu

    2013-11-01

    Different forms of calcium-phosphate (Hydoxyapatite, α-TCP, β-TCP, CDHA) minerals are found to be major component of bone tissue. Development of calcium-phosphate (CaP) based fibrous microstructures is of significant research interest worldwide owing to its improved mechanical properties and higher interconnectivity. Here we represent a method for single step sintered wet-spun Fibers of calcium phosphate from avian egg shells for biomedical applications. Raw egg shell powder was mixed with chitosan solution and Phosphoric acid. The mixture is milled in a ball mill overnight and then filtered. The slurry was de-aired using 100 microliter 1-octanol per 100 ml of slurry as antifoaming and wet spun in coagulation bath. Fiber was dried overnight and sintered at different temperatures for microstructure and phase analysis. Both green and sintered Fibers were physico-chemical characterized by SEM, EDX, XRD, TGA, DSC, FTIR, and stereo-zoom microscopy. The fibers obtained in this procedure are found to have highly porous interconnected structures which can provide good cell adhesion and therefore can be used for bioactive scaffold making.

  5. In vitro studies of calcium phosphate silicate bone cements.

    Science.gov (United States)

    Zhou, Shuxin; Ma, Jingzhi; Shen, Ya; Haapasalo, Markus; Ruse, N Dorin; Yang, Quanzu; Troczynski, Tom

    2013-02-01

    A novel calcium phosphate silicate bone cement (CPSC) was synthesized in a process, in which nanocomposite forms in situ between calcium silicate hydrate (C-S-H) gel and hydroxyapatite (HAP). The cement powder consists of tricalcium silicate (C(3)S) and calcium phosphate monobasic (CPM). During cement setting, C(3)S hydrates to produce C-S-H and calcium hydroxide (CH); CPM reacts with the CH to precipitate HAP in situ within C-S-H. This process, largely removing CH from the set cement, enhances its biocompatibility and bioactivity. The testing results of cell culture confirmed that the biocompatibility of CPSC was improved as compared to pure C(3)S. The results of XRD and SEM characterizations showed that CPSC paste induced formation of HAP layer after immersion in simulated body fluid for 7 days, suggesting that CPSC was bioactive in vitro. CPSC cement, which has good biocompatibility and low/no cytotoxicity, could be a promising candidate as biomedical cement.

  6. Microwave-Assisted Hydrothermal Rapid Synthesis of Calcium Phosphates: Structural Control and Application in Protein Adsorption

    Directory of Open Access Journals (Sweden)

    Zhu-Yun Cai

    2015-07-01

    Full Text Available Synthetic calcium phosphate (CaP-based materials have attracted much attention in the biomedical field. In this study, we have investigated the effect of pH values on CaP nanostructures prepared using a microwave-assisted hydrothermal method. The hierarchical nanosheet-assembled hydroxyapatite (HAP nanostructure was prepared under weak acidic conditions (pH 5, while the HAP nanorod was prepared under neutral (pH 7 and weak alkali (pH 9 condition. However, when the pH value increases to 11, a mixed product of HAP nanorod and tri-calcium phosphate nanoparticle was obtained. The results indicated that the pH value of the initial reaction solution played an important role in the phase and structure of the CaP. Furthermore, the protein adsorption and release performance of the as-prepared CaP nanostructures were investigated by using hemoglobin (Hb as a model protein. The sample that was prepared at pH = 11 and consisted of mixed morphologies of nanorods and nanoprisms showed a higher Hb protein adsorption capacity than the sample prepared at pH 5, which could be explained by its smaller size and dispersed structure. The results revealed the relatively high protein adsorption capacity of the as-prepared CaP nanostructures, which show promise for applications in various biomedical fields such as drug delivery and protein adsorption.

  7. Low temperature method for the production of calcium phosphate fillers

    Directory of Open Access Journals (Sweden)

    Nastro Alfonso

    2004-03-01

    Full Text Available Abstract Background Calcium phosphate manufactured samples, prepared with hydroxyapatite, are used as either spacers or fillers in orthopedic surgery, but these implants have never been used under conditions of mechanical stress. Similar conditions also apply with cements. Many authors have postulated that cements are a useful substitute material when implanted in vivo. The aim of this research is to develop a low cristalline material similar to bone in porosity and cristallinity. Methods Commercial hydroxyapatite (HAp and monetite (M powders are mixed with water and compacted to produce cylindrical samples. The material is processed at a temperature of 37–120 degrees C in saturated steam to obtain samples that are osteoconductive. The samples are studied by X-ray powder diffraction (XRD, Vickers hardness test (HV, scanning electron microscopy (SEM, and porosity evaluation. Results The X-ray diffractions of powders from the samples show patterns typical of HAp and M powders. After thermal treatment, no new crystal phase is formed and no increase of the relative intensity of the peaks is obtained. Vicker hardness data do not show any relationship with treatment temperature. The total porosity decreases by 50–60% according to the specific thermal treatment. Scanning electron microscopy of the surfaces of the samples with either HAp 80%-M 20% (c or Hap 50%-M 50% (f, show cohesion of the powder grains. Conclusions The dissolution-reprecipitation process is more intesive in manufactured samples (c and (f, according to Vickers hardness data. The process occurs in a steam saturated environment between 37 degrees and 120 degrees C. (c (f manufactured samples show pore dimension distributions useful to cellular repopulation in living tissues.

  8. Effects of calcium phosphate bioceramics on skeletal muscle cells.

    Science.gov (United States)

    Sun, J S; Tsuang, Y H; Yao, C H; Liu, H C; Lin, F H; Hang, Y S

    1997-02-01

    With advances in ceramics technology, calcium phosphate bioceramics have been applied as bone substitutes. The effects of implants on bony tissue have been investigated. The effects upon adjacent skeletal muscles have not been determined. The focus of this work is to elucidate the biological effects of various calcium phosphate bioceramics on skeletal muscles. Four different kinds of powder of calcium phosphate biomaterials including beta-tricalcium phosphate (beta-TCP), hydroxyapatite (HA), beta-dicalcium pyrophosphate (beta-DCP) and sintered beta-dicalcium pyrophosphate (SDCP), were tested by myoblast cell cultures. The results were analyzed by cell count, cell morphology and concentration of transforming growth factor beta 1 (TGF-beta 1) in culture medium. The cell population and TGF-beta 1 concentration of the control sample increased persistently as the time of culture increased. The changes in cell population and TGF-beta 1 concentration in culture medium of the beta-TCP and HA were quite low in the first 3 days of culture, then increased gradually toward the seventh day. The changes in cell population and TGF-beta 1 concentration in culture medium of the silica, beta-DCP, and SDCP were quite similar. They were lower during the first day of culture but increased and reached that of the control medium after 7 days' culture. Most cells on B-TCP and HA diminished in size with radially spread, long pseudopods. We conclude that HA and beta-TCP are thought to have an inhibitory effect on growth of the myoblasts. The HA and beta-TCP may interfere with the repair and regeneration of injured skeletal muscle after orthopedic surgery.

  9. Si-TCP synthesized from "Mg-free" reagents employed as calcium phosphate cement

    Directory of Open Access Journals (Sweden)

    Mariana Motisuke

    2012-08-01

    Full Text Available The influence of silicon doping on calcium phosphate cement were explored in this work. α-TCP and Si-α-TCP were prepared by solid state reaction employing "Mg-free" CaHPO4, CaCO3 and CaSiO3 as precursors. It was possible to obtain TCP powders with low contents of β phase as contaminant. Cement liquid phase was an aqueous solution containing 2.5 wt. (% of Na2HPO4 and 1.5 wt. (% of citric acid. The liquid-to-powder ratio was 0.6 mL.g-1. Chemical, physical and mechanical properties of the cement samples were determined by means of XRD, FTIR, XRF, compressive strength and SEM. The calcium phosphate cements obtained achieved satisfactory properties; however, Si-α-TCP presented a decrease on the rate of setting reaction.

  10. Effect of nanostructure on osteoinduction of porous biphasic calcium phosphate ceramics.

    Science.gov (United States)

    Li, Bo; Liao, Xiaoling; Zheng, Li; Zhu, Xiangdong; Wang, Zhe; Fan, Hongsong; Zhang, Xingdong

    2012-10-01

    In order to evaluate the effect of the nanostructure of calcium phosphate ceramics on osteoinductive potential, porous biphasic calcium phosphate (BCP) ceramics with a nano- or submicron structure were prepared via microwave sintering and compared to conventional BCP ceramics. The selective protein adsorption of bovine serum albumin and lysozyme (LSZ) and the osteogenic differentiation of human mesenchymal stem cells in vitro was investigated. Porous BCP nanoceramics showed higher ability to adsorb proteins, especially low molecular weight protein of LSZ, than conventional BCP ceramics, and the BCP nanoceramics promoted bone sialoprotein expression more than conventional BCP did. Further in vivo study to investigate ectopic bone formation and bone repair efficiency proved the highly osteoinductive potential of nanostructured BCP ceramics. The results suggest that nanostructured BCP ceramics have the potential to become a new generation of bioceramics for bone tissue engineering grafts.

  11. Loading and release of doxycycline hyclate from strontium-substituted calcium phosphate cement.

    Science.gov (United States)

    Alkhraisat, M Hamdan; Rueda, C; Cabrejos-Azama, J; Lucas-Aparicio, J; Mariño, F Tamimi; Torres García-Denche, J; Jerez, L Blanco; Gbureck, U; Cabarcos, E Lopez

    2010-04-01

    Novel Sr-substituted calcium phosphate cement (CPC) loaded with doxycycline hyclate (DOXY-h) was employed to elucidate the effect of strontium substitution on antibiotic delivery. The cement was prepared using as reactants Sr-substituted beta-tricalcium phosphate (Sr-beta-TCP) and acidic monocalcium phosphate monohydrate. Two different methods were used to load DOXY-h: (i) the adsorption on CPC by incubating the set cement in drug-containing solutions; and (ii) the use of antibiotic solution as the cement liquid phase. The results revealed that the Sr-substituted cement efficiently adsorbs the antibiotic, which is attributed to an enhanced accessibility to the drug-binding sites within this CPC. DOXY-h desorption is influenced by the initial adsorbed amount and the cement matrix type. Furthermore, the fraction of drug released from CPCs set with DOXY-h solution was higher, and the release rate was faster for the CPC prepared with 26.7% Sr-beta-TCP. The analysis of releasing profiles points to Fickian diffusion as the mechanism responsible for antibiotic delivery. We can conclude that Sr substitution in secondary calcium phosphate cements improves their efficiency for DOXY-h adsorption and release. The antibiotic loading method provides a way to switch from rapid and complete to slower and prolonged drug release. Copyright 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  12. Process for the preparation of calcium superoxide

    Science.gov (United States)

    Ballou, E. V.; Wood, P. C.; Wydeven, T. J.; Spitze, L. A. (Inventor)

    1978-01-01

    Calcium superoxide is prepared in high yields by spreading a quantity of calcium peroxide diperoxyhydrate on the surface of a container, positioning said container in a vacuum chamber on a support structure through which a coolant fluid can be circulated, partially evacuating said vacuum chamber, allowing the temperature of the diperoxyhydrate to reach the range of about 0 to about 40 C; maintaining the temperature selected for a period of time sufficient to complete the disproproriation of the diperoxyhydrate to calcium superoxide, calcium hydroxide, oxygen, and water; constantly and systematically removing the water as it is formed by sweeping the reacting material with a current of dry inert gas and/or by condensation of said water on a cold surface; backfilling the chamber with a dry inert gas; and finally, recovering the calcium superoxide produced.

  13. Vincristine-sulphate-loaded liposome-templated calcium phosphate nanoshell as potential tumor-targeting delivery system.

    Science.gov (United States)

    Thakkar, Hetal Paresh; Baser, Amit Kumar; Parmar, Mayur Prakashbhai; Patel, Ketul Harshadbhai; Ramachandra Murthy, Rayasa

    2012-06-01

    Vincristine-sulfate-loaded liposomes were prepared with an aim to improve stability, reduce drug leakage during systemic circulation, and increase intracellular uptake. Liposomes were prepared by the thin-film hydration method, followed by coating with calcium phosphate, using the sequential addition approach. Prepared formulations were characterized for size, zeta potential, drug-entrapment efficiency, morphology by transmission electron microscopy (TEM), in vitro drug-release profile, and in vitro cell cytotoxicity study. Effect of formulation variables, such as drug:lipid ratio as well as nature and volume of hydration media, were found to affect drug entrapment, and the concentration of calcium chloride in coating was found to affect size and coating efficiency. Size, zeta potential, and TEM images confirmed that the liposomes were effectively coated with calcium phosphate. The calcium phosphate nanoshell exhibited pH-dependent drug release, showing significantly lower release at pH 7.4, compared to the release at pH 4.5, which is the pH of the tumor interstitium. The in vitro cytotoxicity study done on the lung cancer cell line indicated that coated liposomes are more cytotoxic than plain liposomes and drug solution, indicating their potential for intracellular drug delivery. The cell-uptake study done on the lung cancer cell line indicated that calcium-phosphate-coated liposomes show higher cell uptake than uncoated liposomes.

  14. Effect of calcium carbonate on hardening, physicochemical properties, and in vitro degradation of injectable calcium phosphate cements.

    NARCIS (Netherlands)

    Sariibrahimoglu, K.; Leeuwenburgh, S.C.G.; Wolke, J.G.C.; Yubao, L.; Jansen, J.A.

    2012-01-01

    The main disadvantage of apatitic calcium phosphate cements (CPCs) is their slow degradation rate, which limits complete bone regeneration. Carbonate (CO(3)(2)(-)) is the common constituent of bone and it can be used to improve the degradability of the apatitic calcium phosphate ceramics. This study

  15. Calcium phosphate bioceramics induce mineralization modulated by proteins.

    Science.gov (United States)

    Wang, Kefeng; Leng, Yang; Lu, Xiong; Ren, Fuzeng

    2013-08-01

    Proteins play an important role in the process of biomineralization, which is considered the critical process of new bone formation. The calcium phosphate (Ca-P) mineralization happened on hydroxyapatite (HA), β-tricalcium phosphate (β-TCP) and biphasic calcium phosphate (BCP) when proteins presented were investigated systematically. The results reveal that the presence of protein in the revised simulated body fluid (RSBF) did not alter the shape and crystal structure of the precipitated micro-crystals in the Ca-P layer formed on the three types of bioceramics. However, the morphology of the Ca-P precipitates was regulated but the structure of Ca-P crystal was unchanged in vivo. The presence of proteins always inhibits Ca-P mineralization in RSBF and the degree of inhibitory effect is concentration dependent. Furthermore, Protein presence can increase the possibility of HA precipitation in vitro and in vivo. The results obtained in this study can be helpful for better understanding the mechanism of biomineralization induced by the Ca-P bioceramics.

  16. Precipitation of calcium phosphate from moderately acid solution

    Science.gov (United States)

    Lundager Madsen, H. E.; Thorvardarson, G.

    1984-04-01

    The precipitation of calcium phosphate upon mixing of equimolar amounts of calcium nitrate and ammonium phosphate has been studied in the temperature range 40-60°C and pH 3.5-6.5. At the lowertemperatures, brushite, CaHPO 4, 2 H 2O, is the major crystalline product. Monetite, CaHPO 4, is formed at the higher temperatures and above a certain critical supersaturation, and OCP, Ca 4H(PO 4) 3.2.5H 2O, in the higher pH range. A metastable, amorphous tricalcium phosphate, Ca 3(PO 4) 2. xH2O, is formed initially if a(Ca 2+) 3a(PO 3-4) 2 exceeds a certain value, which decreases rapidly as temperature increases. The range in which brushite is found as the only crystalline phase narrows with increasing temperature. The results are explained in terms of heterogeneous nucleation for brushite and homogeneous nucleation for monetite.

  17. The Transformation of Calcium Phosphate Bioceramics in Vivo

    Institute of Scientific and Technical Information of China (English)

    DAI Hong-lian; CAO Xian-ying; LI Xiao-xi; YAN Yu-hua; LI Shi-pu

    2003-01-01

    To study the transformation process of calcium phosphate bioceramic in vivo,biodegradable porous β-tricalcium phosphate ceramics (β-TCP) were used in this experiment. The materials (φ5×8mm) were implanted in the tibia of rabbits. The β-TCP ceramics with bone tissue were retrieved and treated for histology, and then observed by using a scanning electron microscope (SEM) and an electron probe X-ray microanalyzer (EMPA) every month. The results show that β-TCP ceramics bond to bone directly,new bones are forming and maturing with materials continuous degrading,and the materials are nearly replaced by the formed bone finally.Parts of the materials were degraded,absorpted and recrystallized,the others dispersped on the cancellous bone and the Haversian lamella with an irregular arrangement incorporating in bone formation directly by remodeling structure.

  18. Bioactivity of calcium phosphate bioceramic coating fabricated by laser cladding

    Science.gov (United States)

    Zhu, Yizhi; Liu, Qibin; Xu, Peng; Li, Long; Jiang, Haibing; Bai, Yang

    2016-05-01

    There were always strong expectations for suitable biomaterials used for bone regeneration. In this study, to improve the biocompatiblity of titanium alloy, calcium phosphate bioceramic coating was obtained by laser cladding technology. The microstructure, phases, bioactivity, cell differentiation, morphology and resorption lacunae were investigated by optical microscope (OM), x-ray diffraction (XRD), methyl thiazolyl tetrazolium (MTT) assay, tartrate-resistant acid phosphatase (TRAP) staining and scanning electronic microscope (SEM), respectively. The results show that bioceramic coating consists of three layers, which are a substrate, an alloyed layer and a ceramic layer. Bioactive phases of β-tricalcium phosphate (β-TCP) and hydroxyapatite (HA) were found in ceramic coating. Osteoclast precursors have excellent proliferation on the bioceramic surface. The bioceramics coating could be digested by osteoclasts, which led to the resorption lacunae formed on its surface. It revealed that the gradient bioceramic coating has an excellent bioactivity.

  19. Porous Calcium Phosphate Ceramic Scaffolds for Tissue Engineering

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    This study examined the biological response of two porous calcium phosphate ceramics,hydroxyapatite (HA) and hydroxyapaptite/ β-tricalcium phosphate ( HA / β- TCP ) scaffolds. Three different cell types, a human osteoblastic cell line (HOS), primary human osteoblasts (HOB) and human mesenchymal stem cells (MSCs), were used to examine biocompatibility and osteoinductive capacity. The experimental results showed both materials were highly biocompatible and proliferation was significantly greater on pure HA ( P <0.01 ), with a peak in proliferation at day 7. Protein levels were significantly higher ( P < 0.05) than the control Thermanox ( TMX(tm)) for both test materials. Osteoinduction of MSCs was observed on both test materials,with cells seeded on HA/ β- TCP showing greater alkaline phosphatase activity compared to HA alone, indicating an enhancement in osteoinductive property. Both materials show good potential for use as tissue engineered scaffolds.

  20. Injectable biphasic calcium phosphate bioceramic: The HYDROS concept.

    Science.gov (United States)

    Baroth, Serge; Bourges, Xavier; Goyenvalle, Eric; Aguado, Eric; Daculsi, Guy

    2009-01-01

    A new biphasic calcium phosphate ceramic material has been developed in our laboratory. It is composed of 60% of hydroxyapatite and 40% of beta-tricalcium phosphate, based on three granulometries (submicron, round microporous 80-200 mum and macro microporous 0.5-1 mm particles) and hydrated with water leading the formation of a putty filler for bone repair. Biocompatibility and osteogenicity were tested by filling femoral epiphyses critical size bone defect and lumbar muscles in rabbit. After 3, 6 and 12 weeks of implantation, explants were treated for histology. Results revealed the biocompatibility of the material and intensive resorption of the submicron particle fraction followed by important bone ingrowth whereas osteoconduction was provided by the larger particles.

  1. Investigation into the role of NaOH and calcium ions in the synthesis of calcium phosphate nanoshells

    Directory of Open Access Journals (Sweden)

    C. H. Yeo

    2012-03-01

    Full Text Available Calcium phosphate (CaP nanoshells were prepared using negatively charged liposomes (1,2-dioleoyl-sn-glycero-3-phosphate sodium salt (DOPA as a template by base titration synthesis at various concentrations of NaOH and calcium ions. The elemental composition, morphology, particle size, particle size distribution and zeta potential of the products were determined via various characterisation techniques, such as energy-dispersive X-ray spectrometry (EDX, transmission electron microscopy (TEM, dynamic light scattering (DLS, laser Doppler velocimetry (LDV and Fourier transform infrared spectroscopy (FTIR. The best results showed that stable spherical CaP nanoshells with a mean particle size of 197.5 ± 5.8 nm and a zeta potential of -34.5 ± 0.6 mV were successfully formed when 0.100 M sodium hydroxide (NaOH and 0.100 M calcium ions were used. Moreover, an optimal pH of 10.52 and a final Ca/P molar ratio of 0.97 were achieved under these conditions.

  2. New developments in calcium phosphate bone cements: approaching spinal applications

    OpenAIRE

    Vlad, Maria Daniela

    2009-01-01

    La presente tesis doctoral (i.e., “New developments in calcium phosphate bone cements: approaching spinal applications”) aporta nuevos conocimientos en el campo de los cementos óseos de fosfato de calcio (CPBCs) en relación a su aplicación clínica en el campo de la cirugía vertebral mínimamente invasiva. La hipótesis central de esta investigación fue formulada en los siguientes términos: “Los cementos apatíticos pueden ser (si se optimizan) una alternativa mejor (debido a sus propiedades d...

  3. Setting mechanisms of an acidic premixed calcium phosphate cement

    OpenAIRE

    2013-01-01

    Premixed calcium phosphate cements (pCPC), where glycerol is used instead of water as mixing liquid, present better handling characteristics than water-based cements. However, the setting mechanisms of pCPC have not been described thoroughly. The aim of this paper is to increase the understanding of the setting mechanism of pCPC. The investigated cement starts to set when glycerol is exchanged with water via diffusion of glycerol out to the surrounding body fluid and water into the material. ...

  4. Calcium-phosphate-osteopontin particles for caries control

    DEFF Research Database (Denmark)

    Schlafer, Sebastian

    Oftentimes caries lesions develop in protected sites that are difficult to access by self-performed mechanical tooth cleaning. At present, there is a growing interest in chemical adjuncts to mechanical procedures of oral hygiene that aim at biofilm control rather than biofilm eradication. Calcium......-phosphate-osteopontin particles are a new promising therapeutic approach to caries control. They are designed to bind to dental biofilms and interfere with biofilm build-up, lowering the bacterial burden on the tooth surface without affecting bacterial viability in the oral cavity. Moreover, they dissolve when pH in the biofilm...

  5. Physicochemical characterization of zinc-substituted calcium phosphates

    Indian Academy of Sciences (India)

    DOROTA WALCZYK; DAGMARA MALINA; MILENA KRÓL; KLAUDIA PLUTA; AGNIESZKA SOBCZAK-KUPIEC

    2016-04-01

    Biocompatible and bioactive calcium phosphates can make chemical bonds with living bones. Improvement of their biological and physicochemical properties can be achieved by doping with various ions that are presented in natural apatites of bones. These substitutions influence lattice parameters, structure and morphology of apatites. In recent times great attention has been devoted to zinc ions that are the second most abundant trace element present in bones. Zinc embedded into calcium phosphate may enhance the bone formation and in addition exhibits antifungal and antibacterial properties. Therefore, it is rational to form structures incorporated with this ion. In this paper the incorporation of the Zn ions into natural and synthetic calcium phosphates has been reported.Natural hydroxyapatites (HAs) applied in this study were derived mainly from pork bones whereas both brushite and synthetic were formed using wet chemical methods. Ambient temperature synthesis leads to the formation ofbrushite, whereas the process performed at elevated temperature gives HA. Subsequently, attained structures were modified with Zn ions by using in situ or sorption procedures. Phase composition and morphology of obtained materials were determined by means of X-ray diffractometry, Fourier transform infrared spectroscopy and scanning electron microscopy equipped with energy-dispersive spectroscopy. Introduced XRD patterns depict changes of the crystallinity of HA with the increase in the amount of embedded zinc ions. On the contrary, no changes of the crystallinity were observed for the brushite doped with Zn ions. Morphology of attained powders, visualized using scanningelectron microscopy exemplified structural changes between calcium phosphates conjugated with zinc ions. Many authors report that the addition of small amounts of Zn ions leads to loss of crystallinity and decrease of lattice parameters. Interestingly, upon addition of Zn ions to the natural and synthetic HAp by sorption

  6. Calcium phosphate coating on magnesium alloy for modification of degradation behavior

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Magnesium alloy has similar mechanical properties with natural bone,but its high susceptibility to corrosion has limited its application in orthopedics.In this study,a calcium phosphate coating is formed on magnesium alloy (AZ31) to control its degradation rate and enhance its bioactivity and bone inductivity.Samples of AZ31 plate were placed in the supersaturated calcification solution prepared with Ca(NO3)2,NaH2PO4 and NaHCO3,then the calcium phosphate coating formed.Through adjusting the immersion time,the thickness of uniform coatings can be changed from 10 to 20 μm.The composition,phase structure and morphology of the coatings were investigated.Bonding strength of the coatings and substrate was 2-4 MPa in this study.The coatings significantly decrease degradation rate of the original Mg alloy,indicating that the Mg alloy with calcium phosphate coating is a promising degradable bone material.

  7. Effect of different calcium phosphate scaffold ratios on odontogenic differentiation of human dental pulp cells

    Energy Technology Data Exchange (ETDEWEB)

    AbdulQader, Sarah Talib [School of Dental Sciences, Universiti Sains Malaysia, 16150 Kubang Kerian, Kelantan (Malaysia); Department of Pedodontic and Preventive Dentistry, College of Dentistry, University of Baghdad, Baghdad (Iraq); Kannan, Thirumulu Ponnuraj, E-mail: kannan@usm.my [School of Dental Sciences, Universiti Sains Malaysia, 16150 Kubang Kerian, Kelantan (Malaysia); Human Genome Centre, School of Medical Sciences, Universiti Sains Malaysia, 16150 Kubang Kerian, Kelantan (Malaysia); Rahman, Ismail Ab [School of Dental Sciences, Universiti Sains Malaysia, 16150 Kubang Kerian, Kelantan (Malaysia); Ismail, Hanafi [School of Materials and Minerals Resource Engineering, Universiti Sains Malaysia, 14300 Penang (Malaysia); Mahmood, Zuliani [School of Dental Sciences, Universiti Sains Malaysia, 16150 Kubang Kerian, Kelantan (Malaysia)

    2015-04-01

    Calcium phosphate (CaP) scaffolds have been widely and successfully used with osteoblast cells for bone tissue regeneration. However, it is necessary to investigate the effects of these scaffolds on odontoblast cells' proliferation and differentiation for dentin tissue regeneration. In this study, three different hydroxyapatite (HA) to beta tricalcium phosphate (β-TCP) ratios of biphasic calcium phosphate (BCP) scaffolds, BCP20, BCP50, and BCP80, with a mean pore size of 300 μm and 65% porosity were prepared from phosphoric acid (H{sub 2}PO{sub 4}) and calcium carbonate (CaCO{sub 3}) sintered at 1000 °C for 2 h. The extracts of these scaffolds were assessed with regard to cell viability and differentiation of odontoblasts. The high alkalinity, more calcium, and phosphate ions released that were exhibited by BCP20 decreased the viability of human dental pulp cells (HDPCs) as compared to BCP50 and BCP80. However, the cells cultured with BCP20 extract expressed high alkaline phosphatase activity and high expression level of bone sialoprotein (BSP), dental matrix protein-1 (DMP-1), and dentin sialophosphoprotein (DSPP) genes as compared to that cultured with BCP50 and BCP80 extracts. The results highlighted the effect of different scaffold ratios on the cell microenvironment and demonstrated that BCP20 scaffold can support HDPC differentiation for dentin tissue regeneration. - Highlights: • BCPs of different HA/β-TCP ratios influence cell microenvironment. • BCP20 decreases cell viability of HDPCs as compared to BCP50 and BCP80. • HDPCs cultured with BCP20 express highest ALP activity. • HDPCs cultured with BCP20 up-regulate BSP, DMP-1 and DSPP gene expressions. • BCP20 can support HDPC differentiation for dentin tissue regeneration.

  8. Controlled formation of calcium-phosphate-based hybrid mesocrystals by organic-inorganic co-assembly.

    Science.gov (United States)

    Zhai, Halei; Chu, Xiaobin; Li, Li; Xu, Xurong; Tang, Ruikang

    2010-11-01

    An understanding of controlled formation of biomimetic mesocrystals is of great importance in materials chemistry and engineering. Here we report that organic-inorganic hybrid plates and even mesocrystals can be conveniently synthesized using a one-pot reaction in a mixed system of protein (bovine serum albumin (BSA)), surfactant (sodium bis(2-ethylhexyl) sulfosuccinate (AOT)) and supersaturated calcium phosphate solution. The morphologies of calcium-phosphate-based products are analogous to the general inorganic crystals but they have abnormal and interesting substructures. The hybrids are constructed by the alternate stacking of organic layer (thickness of 1.31 nm) and well-crystallized inorganic mineral layer (thickness of 2.13 nm) at the nanoscale. Their morphologies (spindle, rhomboid and round) and sizes (200 nm-2 μm) can be tuned gradually by changing BSA, AOT and calcium phosphate concentrations. This modulation effect can be explained by a competition between the anisotropic and isotropic assembly of the ultrathin plate-like units. The anisotropic assembly confers mesocrystal characteristics on the hybrids while the round ones are the results of isotropic assembly. However, the basic lamellar organic-inorganic substructure remains unchanged during the hybrid formation, which is a key factor to ensure the self-assembly from molecule to micrometre scale. A morphological ternary diagram of BSA-AOT-calcium phosphate is used to describe this controlled formation process, providing a feasible strategy to prepare the required materials. This study highlights the cooperative effect of macromolecule (frame structure), small biomolecule (binding sites) and mineral phase (main component) on the generation and regulation of biomimetic hybrid mesocrystals.

  9. Microstructure and Mechanical Properties of Calcium Phosphate Cement/Gelatine Composite Scaffold with Oriented Pore Structure for Bone Tissue Engineering

    Institute of Scientific and Technical Information of China (English)

    QI Xiaopeng; HE Fupo; YE Jiandong

    2012-01-01

    The macroporous calcium phosphate(CPC) cement with oriented pore structure was prepared by freeze casting.SEM observation showed that the macropores in the porous calcium phosphate cement were interconnected aligned along the ice growth direction.The porosity of the as-prepared porous CPC was measured to be 87.6% by Archimede's principle.XRD patterns of specimens showed that poorly crystallized hydroxyapatite was the main phase present in the hydrated porous calcium phosphate cement.To improve the mechanical properties of the CPC scaffold,the 15% gelatine solution was infiltrated into the pores under vacuum and then the samples were freeze dried to form the CPC/gelatine composite scaffolds.After reinforced with gelatine,the compressive strength of CPC/gelatine composite increased to 5.12 MPa,around fifty times greater than that of the unreinforced macroporous CPC scaffold,which was only 0.1 MPa.And the toughness of the scaffold has been greatly improved via the gelatine reinforcement with a much greater fracture strain.SEM examination of the specimens indicated good bonding between the cement and gelatine.Participating the external load by the deformable gelatine,patching the defects of the CPC pores wall,and crack deflection were supposed to be the reinforcement mechanisms.In conclusion,the calcium phosphate cement/gelatine composite with oriented pore structure prepared in this work might be a potential scaffold for bone tissue engineering.

  10. Microporous calcium phosphate ceramics driving osteogenesis through surface architecture.

    Science.gov (United States)

    Zhang, Jingwei; Barbieri, Davide; ten Hoopen, Hetty; de Bruijn, Joost D; van Blitterswijk, Clemens A; Yuan, Huipin

    2015-03-01

    The presence of micropores in calcium phosphate (CaP) ceramics has shown its important role in initiating inductive bone formation in ectopic sites. To investigate how microporous CaP ceramics trigger osteoinduction, we optimized two biphasic CaP ceramics (i.e., BCP-R and BCP-S) to have the same chemical composition, equivalent surface area per volume, comparable protein adsorption, similar ion (i.e., calcium and phosphate) exchange and the same surface mineralization potential, but different surface architecture. In particular, BCP-R had a surface roughness (Ra) of 325.4 ± 58.9 nm while for BCP-S it was 231.6 ± 35.7 nm. Ceramic blocks with crossing or noncrossing channels of 250, 500, 1000, and 2000 µm were implanted in paraspinal muscle of dogs for 12 weeks. The percentage of bone volume in the channels was not affected by the type of pores (i.e., crossing vs. closed) or their size, but it was greatly influenced by the ceramic type (i.e., BCP-R vs. BCP-S). Significantly, more bone was formed in the channels of BCP-R than in those of BCP-S. Since the two CaP ceramics differed only in their surface architecture, the results hereby demonstrate that microporous CaP ceramics may induce ectopic osteogenesis through surface architecture.

  11. Biocompatibility and resorption of a brushite calcium phosphate cement.

    Science.gov (United States)

    Theiss, Felix; Apelt, Detlef; Brand, Bastian; Kutter, Annette; Zlinszky, Katalin; Bohner, Marc; Matter, Sandro; Frei, Christian; Auer, Joerg A; von Rechenberg, Brigitte

    2005-07-01

    A hydraulic calcium phosphate cement with beta-tricalcium phosphate (TCP) granules embedded in a matrix of dicalcium phosphate dihydrate (DCPD) was implanted in experimentally created defects in sheep. One type of defect consisted of a drill hole in the medial femoral condyle. The other, partial metaphyseal defect was located in the proximal aspect of the tibia plateau and was stabilized using a 3.5 mm T-plate. The bone samples of 2 animals each per group were harvested after 2, 4, 6 and 8 weeks. Samples were evaluated for cement resorption and signs of immediate reaction, such as inflammation, caused by the cement setting in situ. Differences regarding these aspects were assessed for both types of defects using macroscopical, radiological, histological and histomorphometrical evaluations. In both defects the brushite matrix was resorbed faster than the beta-TCP granules. The resorption front was followed directly by a front of new bone formation, in which residual beta-TCP granules were embedded. Cement resorption occurred through (i) extracellular liquid dissolution with cement disintegration and particle formation, and (ii) phagocytosis of the cement particles through macrophages. Signs of inflammation or immunologic response leading to delayed new bone formation were not noticed at any time. Cement degradation and new bone formation occurred slightly faster in the femur defects.

  12. On the development of an apatitic calcium phosphate bone cement

    Indian Academy of Sciences (India)

    Manoj Komath; H K Varma; R Sivakumar

    2000-04-01

    Development of an apatitic calcium phosphate bone cement is reported. 100 Particles of tetracalcium phosphate (TTCP) and dicalcium phosphate dihydrate (DCPD) were mixed in equimolar ratio to form the cement powder. The wetting medium used was distilled water with Na2HPO4 as accelerator to manipulate the setting time. The cement powder, on wetting with the medium, formed a workable putty. The setting times of the putty were measured using a Vicat type apparatus and the compressive strength was determined with a Universal Testing Machine. The nature of the precipitated cement was analyzed through X-ray diffraction (XRD), fourier transform infrared spectrometry (FTIR) and energy dispersive electron microprobe (EDAX). The results showed the phase to be apatitic with a calcium–to–phosphorous ratio close to that of hydroxyapatite. The microstructure analysis using scanning electron microscopy (SEM) showed hydroxyapatite nanocrystallite growth over particulate matrix surface. The structure has an apparent porosity of ∼ 52%. There were no appreciable dimensional or thermal changes during setting. The cement passed the in vitro toxicological screening (cytotoxicity and haemolysis) tests. Optimization of the cement was done by manipulating the accelerator concentration so that the setting time, hardening time and the compressive strength had clinically relevant values.

  13. Calcium phosphate cements: study of the beta-tricalcium phosphate--monocalcium phosphate system.

    Science.gov (United States)

    Mirtchi, A A; Lemaitre, J; Terao, N

    1989-09-01

    The possibility of making cements based on beta-tricalcium phosphate (beta-TCP), a promising bone graft material, was investigated. Upon admixture with water, beta-TCP/monocalcium phosphate monohydrate (MCPM) mixtures were found to set and harden like conventional hydraulic cements. Beta-TCP powders with larger particle size, obtained by sintering at higher temperatures, increased the ultimate strength of the cement. Results show that setting occurs after dissolution of MCPM, as a result of the precipitation of dicalcium phosphate dihydrate (DCPD) in the paste. The ultimate tensile strength of the hardened cement is proportional to the amount of DCPD formed. Upon ageing above 40 degrees C, DCPD transforms progressively into anhydrous dicalcium phosphate (DCP), thereby decreasing the strength. Ageing of the pastes in 100% r.h. results in a decay of the mechanical properties. This can be ascribed to an intergranular dissolution of the beta-TCP aggregates as a result of the pH lowering brought about by the MCPM to DCPD conversion.

  14. New agent to treat elevated phosphate levels: magnesium carbonate/calcium carbonate tablets.

    Science.gov (United States)

    Meyer, Caitlin; Cameron, Karen; Battistella, Marisa

    2012-01-01

    In summary, Binaphos CM, a magnesium carbonate/calcium carbonate combination phosphate binder, is marketed for treating elevated phosphate levels in dialysis patients. Although studies using magnesium/calcium carbonate as a phosphate binder are short term with small numbers of patients, this phosphate binder has shown some promising results and may provide clinicians with an alternative for phosphate binding. Using a combination phosphate binder may reduce pill burden and encourage patient compliance. In addition to calcium and phosphate, it is imperative to diligently monitor magnesium levels in patients started on this medication, as magnesium levels may increase with longer duration of use. Additional randomized controlled trials are necessary to evaluate long-term efficacy and safety of this combination phosphate binder.

  15. Effects of phosphates on microstructure and bioactivity of micro-arc oxidized calcium phosphate coatings on Mg-Zn-Zr magnesium alloy.

    Science.gov (United States)

    Pan, Y K; Chen, C Z; Wang, D G; Zhao, T G

    2013-09-01

    Calcium phosphate (CaP) coatings were prepared on Mg-Zn-Zr magnesium alloy by micro-arc oxidation (MAO) in electrolyte containing calcium acetate monohydrate (CH3COO)2Ca·H2O) and different phosphates (i.e. disodium hydrogen phosphate dodecahydrate (Na2HPO4·12H2O), sodium phosphate (Na3PO4·H2O) and sodium hexametaphosphate((NaPO3)6)). Scanning electron microscope (SEM), energy-dispersive X-ray spectrometry (EDS) and X-ray diffractometer (XRD) were employed to characterize the microstructure, elemental distribution and phase composition of the CaP coatings. Simulated body fluid (SBF) immersion test was used to evaluate the coating bioactivity and degradability. Systemic toxicity test was used to evaluate the coating biocompatibility. Fluoride ion selective electrode (ISE) was used to measure F(-) ions concentration during 30 days SBF immersion. The CaP coatings effectively reduced the corrosion rate and the surfaces of CaP coatings were covered by a new layer formed of numerous needle-like and scale-like apatites. The formation of these calcium phosphate apatites indicates that the coatings have excellent bioactivity. The coatings formed in (NaPO3)6-containging electrolyte exhibit thicker thickness, higher adhesive strength, slower degradation rate, better apatite-inducing ability and biocompatibility. Copyright © 2013 Elsevier B.V. All rights reserved.

  16. The increasing of enamel calcium level after casein phosphopeptideamorphous calcium phosphate covering

    Directory of Open Access Journals (Sweden)

    Widyasri Prananingrum

    2012-06-01

    Full Text Available Background: Caries process is characterized by the presence of demineralization. Demineralization is caused by organic acids as a result of carbohydrate substrate fermentation. Remineralization is a natural repair process for non-cavitated lesions. Remineralization occurs if there are Ca2+ and PO43- ions in sufficient quantities. Casein-amorphous calcium phosphate phosphopeptide (CPP-ACP is a paste material containing milk protein (casein, that actually contains minerals, such as calcium and phosphate. The casein ability to stabilize calcium phosphate and enhance mineral solubility and bioavailability confers upon CPP potential to be biological delivery vehicles for calcium and phosphate. Purpose: The aim of this study was to determine the calcium levels in tooth enamel after being covered with CPP-ACP 2 times a day for 3, 14 and 28 days. Methods: Sample were bovine incisors of 3 year old cows divided into 4 groups, namely group I as control group, group II, III and IV as treatment groups covered with CPP-ACP 2 times a day. All of those teeth were then immersed in artificial saliva. Group II was immersed for 3 days, while group III was immersed for 14 days, and group IV was immersed for 28 days. One drop of CPP-ACP was used to cover the entire labial surface of teeth. The measurement of the calcium levels was then conducted by using titration method. All data were analyzed by One- Way ANOVA test with 5% degree of confidence. Results: The results showed significant difference of the calcium levels in tooth enamel of those groups after covered with CPP-ACP 2 times a day for 3, 14 and 28 days (p = 0.001. There is also significant difference of the calcium levels in tooth enamel of those treatment groups and the control group (p = 0.001. Conclusion: The calcium levels of tooth enamel are increased after covered with CPP-ACP 2 times a day for 3, 14 and 28 days.Latar belakang: Proses terjadinya karies gigi ditandai oleh adanya demineralisasi

  17. Si-TCP Synthesized from "Mg-free" Reagents Employed as Calcium Phosphate Cement

    OpenAIRE

    Mariana Motisuke; Raul García Carrodeguas; Cecília Amélia Carvalho Zavaglia

    2012-01-01

    The influence of silicon doping on calcium phosphate cement were explored in this work. α-TCP and Si-α-TCP were prepared by solid state reaction employing "Mg-free" CaHPO4, CaCO3 and CaSiO3 as precursors. It was possible to obtain TCP powders with low contents of β phase as contaminant. Cement liquid phase was an aqueous solution containing 2.5 wt. (%) of Na2HPO4 and 1.5 wt. (%) of citric acid. The liquid-to-powder ratio was 0.6 mL.g-1. Chemical, physical and mechanical propert...

  18. The effect of calcium phosphate microstructure on bone-related cells in vitro

    NARCIS (Netherlands)

    Li, Xiaoming; van Blitterswijk, Clemens; Feng, Qingling; Cui, Fuzhai; Watari, Fumio

    2008-01-01

    Microstructure is essential for inductive bone formation in calcium phosphate materials after soft tissue implantation. We hereby evaluated activities (cell attachment, proliferation, ALP/DNA and protein/DNA) of three types of cells cultured on three kinds of calcium phosphate ceramic discs to study

  19. Synthesis and characterization of nanosized calcium phosphates by flame spray pyrolysis, and their effect on osteogenic differentiation of stem cells

    Energy Technology Data Exchange (ETDEWEB)

    Ataol, Sibel; Tezcaner, Ayşen [Middle East Technical University, Department of Biomedical Engineering (Turkey); Duygulu, Ozgur [TUBITAK Marmara Research Center, Materials Institute (Turkey); Keskin, Dilek [Middle East Technical University, Department of Biomedical Engineering (Turkey); Machin, Nesrin E., E-mail: nesrinmachin@gmail.com [Kocaeli University, Department of Chemical Engineering (Turkey)

    2015-02-15

    The present study evaluates the synthesis of biocompatible osteoconductive and osteoinductive nano calcium phosphate (CaP) particles by industrially applied, aerosol-derived flame spray pyrolysis method for biomedical field. Calcium phosphate nanoparticles were produced in a range of calcium-to-phosphorus ratio, (1.20–2.19) in order to analyze the morphology and crystallinity changes, and to test the bioactivity of particles. The characterization results confirmed that nanometer-sized, spherical calcium phosphate particles were produced. The average primary particle size was determined as 23 nm by counting more than 500 particles in TEM pictures. XRD patterns, HRTEM, SAED, and SEM analyses revealed the amorphous nature of the as-prepared nano calcium phosphate particles at low Ca/P ratios. Increases in the specific surface area and crystallinity were observed with the increasing Ca/P ratio. TGA–DTA analysis showed that the thermally stable crystal phases formed after 700 °C. Cell culture studies were conducted with urine-derived stem cells that possess the characteristics of mesenchymal stem cells. Synthesized amorphous nanoparticles did not have cytotoxic effect at 5–50 μg/ml concentration range. Cells treated with the as-prepared nanoparticles had higher alkaline phosphatase (ALP) enzyme activity than control cells, indicating osteogenic differentiation of cells. A slight decrease in ALP activity of cells treated with two highest Ca:P ratios at 50 μg/ml concentration was observed at day 7. The findings suggest that calcium phosphate nanoparticles produced in this work have a potential to be used as biomaterials in biomedical applications.

  20. Calcium phosphate flocs and the clarification of sugar cane juice from whole of crop harvesting.

    Science.gov (United States)

    Thai, Caroline C D; Moghaddam, Lalehvash; Doherty, William O S

    2015-02-11

    Sugar cane biomass is one of the most viable feedstocks for the production of renewable fuels and chemicals. Therefore, processing the whole of crop (WC) (i.e., stalk and trash, instead of stalk only) will increase the amount of available biomass for this purpose. However, effective clarification of juice expressed from WC for raw sugar manufacture is a major challenge because of the amounts and types of non-sucrose impurities (e.g., polysaccharides, inorganics, proteins, etc.) present. Calcium phosphate flocs are important during sugar cane juice clarification because they are responsible for the removal of impurities. Therefore, to gain a better understanding of the role of calcium phosphate flocs during the juice clarification process, the effects of impurities on the physicochemical properties of calcium phosphate flocs were examined using small-angle laser light scattering technique, attenuated total reflectance Fourier transformed infrared spectroscopy, and X-ray powder diffraction. Results on synthetic sugar juice solutions showed that the presence of SiO2 and Na(+) ions affected floc size and floc structure. Starch and phosphate ions did not affect the floc structure; however, the former reduced the floc size, whereas the latter increased the floc size. The study revealed that high levels of Na(+) ions would negatively affect the clarification process the most, as they would reduce the amount of suspended particles trapped by the flocs. A complementary study on prepared WC juice using cold and cold/intermediate liming techniques was conducted. The study demonstrated that, in comparison to the one-stage (i.e., conventional) clarification process, a two-stage clarification process using cold liming removed more polysaccharides (≤19%), proteins (≤82%), phosphorus (≤53%), and SiO2 (≤23%) in WC juice but increased Ca(2+) (≤136%) and sulfur (≤200%).

  1. Dissolution and storage stability of nanostructured calcium carbonates and phosphates for nutrition

    Science.gov (United States)

    Posavec, Lidija; Knijnenburg, Jesper T. N.; Hilty, Florentine M.; Krumeich, Frank; Pratsinis, Sotiris E.; Zimmermann, Michael B.

    2016-10-01

    Rapid calcium (Ca) dissolution from nanostructured Ca phosphate and carbonate (CaCO3) powders may allow them to be absorbed in much higher fraction in humans. Nanosized Ca phosphate and CaCO3 made by flame-assisted spray pyrolysis were characterized by nitrogen adsorption, X-ray diffraction (XRD), Raman spectroscopy, and transmission electron microscopy. As-prepared nanopowders contained both CaCO3 and CaO, but storing them under ambient conditions over 130 days resulted in a complete transformation into CaCO3, with an increase in both crystal and particle sizes. The small particle size could be stabilized against such aging by cation (Mg, Zn, Sr) and anion (P) doping, with P and Mg being most effective. Calcium phosphate nanopowders made at Ca:P ≤ 1.5 were XRD amorphous and contained γ-Ca2P2O7 with increasing hydroxyapatite content at higher Ca:P. Aging of powders with Ca:P = 1.0 and 1.5 for over 500 days gradually increased particle size (but less than for CaCO3) without a change in phase composition or crystallinity. In 0.01 M H3PO4 calcium phosphate nanopowders dissolved ≈4 times more Ca than micronsized compounds and about twice more Ca than CaCO3 nanopowders, confirming that nanosizing and/or amorphous structuring sharply increases Ca powder dissolution. Because higher Ca solubility in vitro generally leads to greater absorption in vivo, these novel FASP-made Ca nanostructured compounds may prove useful for nutrition applications, including supplementation and/or food fortification.

  2. [Allergy of calcium phosphate cement material following skull reconstruction: a case report].

    Science.gov (United States)

    Mizowaki, Takashi; Miyake, Shigeru; Yoshimoto, Yuji; Matsuura, Yoshitaka; Akiyama, Sou

    2013-04-01

    The paste form of calcium phosphate cement is often used in skull reconstruction because of the biocompatibility and early handling of these cements. Although it had rarely been shown to produce a foreign body reaction, we encountered a patient who experienced an allergic reaction to calcium phosphate cements(Biopex®. A patch test was performed and a positive reaction to magnesium phosphate was obtained. Biopex® contains magnesium phosphate, so we diagnosed this case as allergic reaction. Pathological analysis revealed infiltration of plasmacytes in the bone flap around the calcium phosphate cement. The postoperative course was uneventful 3 years after surgery. Allergy to calcium phosphate cements is rare, but must be considered in differential diagnosis of its side effects.

  3. Injectable Hydrogel Composite Based Gelatin-PEG and Biphasic Calcium Phosphate Nanoparticles for Bone Regeneration

    Science.gov (United States)

    Van, Thuy Duong; Tran, Ngoc Quyen; Nguyen, Dai Hai; Nguyen, Cuu Khoa; Tran, Dai Lam; Nguyen, Phuong Thi

    2016-05-01

    Gelatin hydrogels have recently attracted much attention for tissue regeneration because of their biocompatibility. In this study, we introduce poly-ethylene glycol (PEG)—grafted gelatin containing tyramine moieties which have been utilized for in situ enzyme-mediated hydrogel preparation. The hydrogel can be used to load nanoparticles of biphasic calcium phosphate, a mixture of hydroxyapatite and β-tricalcium phosphate, and forming injectable bio-composites. Proton nuclear magnetic resonance (1H NMR) spectra indicated that tyramine-functionalized polyethylene glycol-nitrophenyl carbonate ester was conjugated to the gelatin. The hydrogel composite was rapidly formed in situ (within a few seconds) in the presence of horseradish peroxidase and hydrogen peroxide. In vitro experiments with bio-mineralization on the hydrogel composite surfaces was well-observed after 2 weeks soaking in simulated body fluid solution. The obtained results indicated that the hydrogel composite could be a potential injectable material for bone regeneration.

  4. Preparation and Characterization of Calcium Carbonate Nanoparticles

    Science.gov (United States)

    Hassim, Aqilah; Rachmawati, Heni

    2010-10-01

    Taking calcium supplements can reduce the risk of developing osteoporosis, but they are not readily absorbed in the gastrointestinal tract. Nanotechnology is expected to resolve this problem. In this study, we prepared and characterized calcium carbonate nanoparticle to improve the solubility by using bottom-up method. The experiment was done by titrating calcium chloride with sodium carbonate with the addition of polyvinylpyrrolidone (PVP) as stabilizer, using ultra-turrax. Various concentrations of calcium chloride and sodium carbonate as well as various speed of stirring were used to prepare the calcium carbonate nanoparticles. Evaluations studied were including particle size, polydispersity index (PI) and zeta potential with particle analyzer, surface morphology with scanning electron microscope, and saturated solubility. In addition, to test the ability of PVP to prevent particles growth, short stability study was performed by storing nano CaCO3 suspension at room temperature for 2 weeks. Results show that using 8000 rpm speed of stirring, the particle size tends to be bigger with the range of 500-600 nm (PI between 0.2-0.4) whereas with stirring speed of 4000 rpm, the particle size tends to be smaller with 300-400 nm (PI between 0.2-0.4). Stirring speed of 6000 rpm produced particle size within the range of 400-500 nm (PI between 0.2-0.4). SEM photograph shows that particles are monodisperse confirming that particles were physically stable without any agglomeration within 2 weeks storage. Taken together, nano CaCO3 is successfully prepared by bottom-up method and PVP is a good stabilizer to prevent the particle growth.

  5. Introduction of enzymatically degradable poly(trimethylene carbonate) microspheres into an injectable calcium phosphate cement.

    Science.gov (United States)

    Habraken, Wouter J E M; Zhang, Zheng; Wolke, Joop G C; Grijpma, Dirk W; Mikos, Antonios G; Feijen, Jan; Jansen, John A

    2008-06-01

    Poly(trimethylene carbonate) (PTMC) is an enzymatically degradable polyester with rubber-like properties. Introduction of this polymer into an injectable calcium phosphate bone cement can therefore be used to introduce macroporosity into the cement for tissue engineering purposes as well as to improve mechanical properties. Aim of this study was to investigate calcium phosphate cements with incorporated PTMC microspheres (PTMC CPCs) on their physical/mechanical properties and in vitro degradation characteristics. Therefore, composites were tested on setting time and mechanical strength as well as subjected to phosphate buffered saline (PBS) and enzyme containing medium. PTMC CPCs (12.5 and 25 wt%) with molecular weights of 52.7 kg mol(-1) and 176.2 kg mol(-1) were prepared, which showed initial setting times similar to that of original CPC. Though compression strength decreased upon incorporation of PTMC microspheres, elastic properties were improved as strain-at-yield increased with increasing content of microspheres. Sustained degradation of the microspheres inside PTMC CPC occurred when incubated in the enzymatic environment, but not in PBS, which resulted in an interconnected macroporosity for the 25 wt% composites.

  6. Augmentation of Pedicle Screw Fixation with Calcium Phosphate Cement

    Institute of Scientific and Technical Information of China (English)

    YANG Shu-hua; FU De-hao; LI Jin; XU Wei-hua; YANG Cao; YE Zhe-wei; ZUO Xiao-yan

    2004-01-01

    To determine whether a biodegradable calcium phosphate cement(CPC) provides significant augmentation of pedicle screw fixation or not,an in vitro biomechanical study was carried out to evaluate the biomechanical effect of CPC in the restoration and augmentation of pedicle screw fixation.Axial pullout test and cyclic bending resistance test were employed in the experiment,and polymethylmethacrylate (PMMA) was chosen as control.The results demonstrate that the pullout strengths following CPC restoration and augmentation are 74% greater on an average than those of the control group,but less than those of PMMA restoration group and augmentation group respectively (increased by 126% versus control).In cyclic bending resistance test,the CPC augmented screws are found to withstand a greater number of cycles or greater loading with less displacement before loosening,but the augmentation effect of PMMA is greater than that of CPC.

  7. Coating of calcium phosphate on biometallic materials by electrophoretic deposition

    Institute of Scientific and Technical Information of China (English)

    ZHANG Er-lin; YANG Ke

    2005-01-01

    Although biometallic materials have been used as bone implant materials for a long time, they are still detected as foreign bodies by human immune system. Calcium phosphate coating, especially hydroxyapatite(HA)coating attracts special attention due to its good biocompatibility. Being one of the effective methods used to deposit HA coating onto the metallic implant, the electrophoretic deposition(EPD) was reviewed in detail, including the process of EPD, the advantages and disadvantages, the important processing factors and the microstructure and mechanical properties of the coating. Research results on the processing and the coating show potential application of EPD process to the biomedical materials surface modification. In addition, the nanoparticulate HA coating as a new trend in HA coating was also introduced.

  8. Regulation of calcium phosphate formation by native amelogenins in vitro.

    Science.gov (United States)

    Kwak, Seo-Young; Kim, Sonia; Yamakoshi, Yasuo; Simmer, James P; Beniash, Elia; Margolis, Henry C

    2014-08-01

    Our previous in vitro studies have shown that recombinant full-length porcine amelogenin rP172 can transiently stabilize amorphous calcium phosphate (ACP) and uniquely guide the formation of well-aligned bundles of hydroxyapatite (HA) crystals, as seen in the secretory stage of amelogenesis. This functional capacity is dependent on the hydrophilic C-terminal domain of full-length amelogenin. However, we have also found that native phosphorylated (single S-16 site) forms of full-length (P173) and C-terminal cleaved (P148) amelogenins can stabilize ACP for > 2 d and prevent HA formation. The present study was carried out to test the hypothesis that, at reduced concentrations, native full-length P173 also has the capacity to guide ordered HA formation. The effect of P148 and P173 concentrations (0.2-2.0 mg/ml) on the rate of spontaneous calcium phosphate precipitation was monitored via changes in solution pH, while mineral phases formed were assessed using TEM. At higher P173 concentrations (1.0-2.0 mg/ml), limited mineral formation occurred and only ACP nanoparticles were observed during a 48 h period. However, at 0.4 mg/ml P173, a predominance of organized bundles of linear, needle-like HA crystals were observed. At 0.2 mg/ml of P173, limited quantities of less organized HA crystals were found. Although P148 similarly stabilized ACP, it did not guide ordered HA formation, like P173. Hence, the establishment of the hierarchical enamel structure during secretory stage amelogenesis may be regulated by the partial removal of full-length amelogenin via MMP20 proteolysis, while predominant amelogenin degradation products, like P148, serve to prevent uncontrolled mineral formation.

  9. Alendronate-Eluting Biphasic Calcium Phosphate (BCP Scaffolds Stimulate Osteogenic Differentiation

    Directory of Open Access Journals (Sweden)

    Sung Eun Kim

    2015-01-01

    Full Text Available Biphasic calcium phosphate (BCP scaffolds have been widely used in orthopedic and dental fields as osteoconductive bone substitutes. However, BCP scaffolds are not satisfactory for the stimulation of osteogenic differentiation and maturation. To enhance osteogenic differentiation, we prepared alendronate- (ALN- eluting BCP scaffolds. The coating of ALN on BCP scaffolds was confirmed by scanning electron microscopy (FE-SEM, energy-dispersive X-ray spectroscopy (EDS, and attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR. An in vitro release study showed that release of ALN from ALN-eluting BCP scaffolds was sustained for up to 28 days. In vitro results revealed that MG-63 cells grown on ALN-eluting BCP scaffolds exhibited increased ALP activity and calcium deposition and upregulated gene expression of Runx2, ALP, OCN, and OPN compared with the BCP scaffold alone. Therefore, this study suggests that ALN-eluting BCP scaffolds have the potential to effectively stimulate osteogenic differentiation.

  10. Growth units and nucleation: The case of calcium phosphates

    Science.gov (United States)

    Boistelle, Roland; Lopez-Valero, Isabel

    1990-05-01

    Calcium phosphates are precipitated at 37°C from solutions the pH of which ranges from 5.0 to 11.0. Despite the fact that the supersaturations of hydroxyapatite HAP, octocalcium phosphate OCP and brushite B are often in the order HAP≫OCP≫B, brushite nucleates more easily than OCP and HAP at low pH, while OCP nucleates more easily than HAP at mean to high pH. These facts cannot be explained, as usually, by the only differences in the surface free energies of the three solid phases. On the other hand, they may be explained by assuming that the values of the kinetic coefficients change as a function of the concentration in the proper growth units which have to integrate in the nuclei of either phase. In the model we propose, the kinetic coefficients of OCP and HAP are smaller than that of B by 10 and 18 orders of magnitude at pH=6.5, differences which reduce to 3 orders of magnitude at pH=10.0. Accordingly, nucleation of OCP and HAP is favoured with increasing pH.

  11. In vitro ageing of brushite calcium phosphate cement.

    Science.gov (United States)

    Grover, L M; Knowles, J C; Fleming, G J P; Barralet, J E

    2003-10-01

    In vivo studies investigating the use of brushite cements have demonstrated mixed results with one or more of dissolution, hydrolysis, fragmentation and long term stability being demonstrated. It has been suggested that sample volume, implant location, and species can affect in vivo behaviour. As few in vitro studies on this cement system have been performed, this study aimed to compare the effects of static and dynamic in vitro ageing protocols on the phase composition, weight loss and mechanical properties of brushite cement. The effects of immersion liquid to cement volume ratio (LCVR) and sample volume on phase composition were investigated and comparative in vitro experiments were also performed in foetal bovine serum. It was determined that the weight loss after 28 days was up to seven times higher in serum than in phosphate buffered saline (PBS) and that fragmentation accounted for most of the weight loss observed. Hydroxyapatite was formed in PBS but not in serum when aged in refreshed media at all LCVRs investigated. This study has highlighted that LCVR, media refresh rate and media composition are critical to brushite cement performance. It appears that brushite cement removal from an implant site may be complex and dependent on physiological processes other than simple dissolution. A better understanding of these processes could provide the means to engineer more precise calcium phosphate cement degradation profiles.

  12. Osteoregenerative capacities of dicalcium phosphate-rich calcium phosphate bone cement.

    Science.gov (United States)

    Ko, Chia-Ling; Chen, Jian-Chih; Tien, Yin-Chun; Hung, Chun-Cheng; Wang, Jen-Chyan; Chen, Wen-Cheng

    2015-01-01

    Calcium phosphate cement (CPC) is a widely used bone substitute. However, CPC application is limited by poor bioresorption, which is attributed to apatite, the stable product. This study aims to systematically survey the biological performance of dicalcium phosphate (DCP)-rich CPC. DCP-rich CPC exhibited a twofold, surface-modified DCP anhydrous (DCPA)-to-tetracalcium phosphate (TTCP) molar ratio, whereas conventional CPC (c-CPC) showed a onefold, surface unmodified DCPA-to-TTCP molar ratio. Cell adhesion, morphology, viability, and alkaline phosphatase (ALP) activity in the two CPCs were examined with bone cell progenitor D1 cultured in vitro. Microcomputed tomography and histological observation were conducted after CPC implantation in vivo to analyze the residual implant ratio and new bone formation rate. D1 cells cultured on DCP-rich CPC surfaces exhibited higher cell viability, ALP activity, and ALP quantity than c-CPC. Histological evaluation indicated that DCP-rich CPC showed lesser residual implant and higher new bone formation rate than c-CPC. Therefore, DCP-rich CPC can improve bioresorption. The newly developed DCP-rich CPC exhibited potential therapeutic applications for bone reconstruction.

  13. Penggunaan batuan fosfat NDCP (natural defluorinated calcium phosphate sebagai pengganti dicalcium phosphate dalam ransom ayam broiler

    Directory of Open Access Journals (Sweden)

    Arnold P. Sinurat

    1995-08-01

    Full Text Available An experiment was conducted to study the utilization of local rock phosphate or natural defluorinated calcium phosphate (NDCP as phosphorus source for broilers by using the imported dicalcium phosphate (DCP as a reference. The study was designed by formulating 6 experimental diets which consist of 2 phosphorus sources (DCP dan NDCP and 3 dietary total P levels (0 .55 ; 0.65 and 0 .75%. Each diet was fed to 60 chickens (10 replicates with 6 birds each from three day old to 6 weeks of age. Parameters observed were feed consumption, body weight gain, mortality, Ca and P retention, and ash content of tibia bones. Results showed that dietary phosphorus levels (0.55 to 0.75% did not significantly affect body weight gain, feed consumption, and mortalities. However, better feed conversion ratio was obtained when dietary phosphorus level was 0.55%. The NDCP treated birds could significantly gain heavier weight compared with those received DCP, although this improvement was also followed by an increase in the feed consumption. The relative biological value of phosphorus in NDCP was 101 `7n. It is concluded that NDCP can he used in broilers diet to replace DCP as phosphorus source.

  14. In Vitro Investigation of Bioactive Glass-Ceramic Composites Based on Biogenic Hydroxyapatite or Synthetic Calcium Phosphates

    Science.gov (United States)

    Pinchuk, Nataliia; Parkhomey, Oleksandr; Sych, Olena

    2017-02-01

    This in vitro investigation of the behavior of two types of calcium phosphate glass ceramics on the basis of phosphates of biogenic or synthetic origin prepared from initial mixtures with different particle size has revealed that some different factors affect the behavior, namely the phase composition of composite, fraction of open porosity, and average diameter of pore channels. It was established that the solubility of the composites on the basis of synthetic calcium phosphates and glass after 2 and 7 days contact with saline composites is the highest among the materials under study. First of all, this fact is related to the peculiarities of their phase composition, high fraction of open porosity, and high permeability. As for biogenic hydroxyapatite/glass materials, their solubility is several times lower in spite of close total porosity. The particle size of initial mixture practically does not affect the material solubility; the latter is only slightly lower for smaller particles.

  15. The fabrication of nanocomposites via calcium phosphate formation on gelatin-chitosan network and the gelatin influence on the properties of biphasic composites

    Energy Technology Data Exchange (ETDEWEB)

    Babaei, Zahra [Nanotechnology Research Institute, School of Chemical Engineering, Babol University of Technology, Babol (Iran, Islamic Republic of); Jahanshahi, Mohsen, E-mail: mjahan@nit.ac.ir [Nanotechnology Research Institute, School of Chemical Engineering, Babol University of Technology, Babol (Iran, Islamic Republic of); Rabiee, Sayed Mahmood [Nanotechnology Research Institute, School of Chemical Engineering, Babol University of Technology, Babol (Iran, Islamic Republic of); School of Mechanical Engineering, Babol University of Technology, Babol (Iran, Islamic Republic of)

    2013-01-01

    A novel biodegradable polymer-ceramic nanocomposite which consisted of gelatin (Gel), chitosan (CS), and calcium phosphate (CaP) nanoparticles was prepared based on in situ preparation method. The fabricated biocomposites were characterized by FTIR, X-ray diffraction (XRD), transmission electron microscopy (TEM) as well as scanning electron microscope with X-ray elemental analysis (SEM-EDX). The characterization results confirmed that the crystalline calcium phosphate nanoparticles were mineralized in polymeric matrix and the interaction between Ca2+ in calcium phosphate and functional groups in polymers molecular chains was formed. XRD result showed that in addition to hydroxyapatite (HA), Brushite (BR) and tricalcium phosphate ({beta}-TCP) particles also were formed due to lack of complete penetration of the basic solution into the polymeric matrix. However, SEM image indicated that the polymeric matrix has the controlling role in the particle size of calcium phosphate. The size of particles in three component composites was about 100 nm while in two component composites proved to be more in {mu}m size. TEM observation supported SEM results and showed that the three component composites have calcium phosphate nanoparticles. The elastic modulus and compressive strength of the composites were also improved by the employment of gelatin and chitosan together, which can make them more beneficial for surgical applications. - Highlights: Black-Right-Pointing-Pointer A new type of calcium phosphate nanocomposites consisted chitosan and gelatin as polymeric matrix was obtained via in situ precipitation method. Black-Right-Pointing-Pointer The formed particles into the polymeric matrix are hydroxyapatite, Brushite and {beta}-tricalcium phosphate. Black-Right-Pointing-Pointer The polymer concentration is a predominant factor for inhibiting nucleation and growth of calcium phosphate particles as the particles size was also decreased by increasing the amount of polymeric

  16. The utilization of rock phosphate (natural defluorinated calcium phosphate or NDCP in laying hens diet to replace dicalcium phosphate

    Directory of Open Access Journals (Sweden)

    A.P Sinurat

    1996-06-01

    Full Text Available An experimentwas conducted to study the utilization of local rock phosphate or natural defluorinated calcium phosphate (NDCP as phosphorus source for layer chickens by using the imported dicalcium phosphate (DCP as a reference. Eight experimental diets consisted of 2 source of phosphorus (DCP and NDCP and 4 dietary total P levels (0.4, 0.5, 0.6 and 0.7% were formulated. Each diet was fed to 24 pullets (6 replicates with 4 birds each from 20 weeks of age to 14 weeks of egg production. Observations were made on feed consumption, egg production, egg weight, mortality, egg quality, Ca and P retention and ash content of tibial bones . Results showed no significant effect of different source and level of phosphorus tested on egg production (% HD, feed consumption, egg weight and mortality rates . Egg shell thickness was depressed in NDCP diet as compared with DCP, however this only occurred at firstmonth of production. It is concluded that the NDCP can be used in layers diet to replace DCP as phosphorus source. The relative biological value of phosphorus inNDCP is 96% for layers.

  17. Randomized crossover study comparing the phosphate-binding efficacy of calcium ketoglutarate versus calcium carbonate in patients on chronic hemodialysis

    DEFF Research Database (Denmark)

    Bro, S; Rasmussen, R A; Handberg, J

    1998-01-01

    The objective of the study was to evaluate the phosphate-binding efficacy, side effects, and cost of therapy of calcium ketoglutarate granulate as compared with calcium carbonate tablets in patients on chronic hemodialysis. The study design used was a randomized, crossover open trial, and the main...

  18. Composition of calcium phosphates precipitated from aqueous solutions at different pH values

    Energy Technology Data Exchange (ETDEWEB)

    Salahi, E.; Moztarzadeh, F. [Ceramics Div., Teheran (Iran). Materials and Energy Research Center

    2001-03-01

    During the preparation of calcium phosphate compounds by precipitation from aqueous solutions, several phases, namely dicalcium hydrogen phosphate (DCP, CaHPO{sub 4}), dicalcium hydrogen phosphate dihydrate DCPD, CaHPO{sub 4} (2 H{sub 2}O), hydrated calcium phosphate Ca{sub 3}(PO){sub 4} 2(H{sub 2}O) and hydroxyapatite (HAp, Ca10(PO{sub 4})6(OH){sub 2}), can be formed at different pH values. In the research work presented here, Ca(NO{sub 3})2(4H{sub 2}O) and (NH{sub 4})2HPO{sub 4} were used as starting materials The two solutions with an initial molar ratio of Ca/P=1,67 were mixed at 20 C at 0calcium phosphate are formed. A structural transition was observed at 8phosphate ({beta}-TCP,Ca{sub 3}(PO{sub 4}){sub 2}) developed. Between pH 8 and 9, this phase could be observed clearly. At pH 9..10, there is a transitional state, and at pH >10,5, the hydroxyapatite was developed completely. (orig.)

  19. The initial phases of calcium and magnesium phosphates precipitated from solutions of high to medium concentrations

    Science.gov (United States)

    Abbona, F.; Madsen, H. E. Lundager; Boistelle, R.

    1986-04-01

    The precipitation of calcium and magnesium phosphates is performed at 25°C by mixing solutions of ammonium phosphate and solutions of calcium and magnesium chlorides under the condition [ P] = [ Ca] + [ Mg] in large pH intervals. Before any nucleation the phosphate concentration ranges from 0.50M to 0.01M. The phases first precipitated are CaHPO 4·2H 2O (brushite), CaHPO 4 (monetite), Ca 3(PO 4) 2· xH 2O (amorphous calcium phosphate), MgNH 4PO 4·6H 2O (struvite), and MgHPO 4·3H 2O (newberyite). The precipitation fields of each phase are determined and discussed as a function of pH, composition and supersaturation. The solutions are even supersaturated with respect to several other calcium phosphates but they never occur first even if their supersaturation is the highest.

  20. Thermo-tolerant phosphate-solubilizing microbes for multi-functional biofertilizer preparation.

    Science.gov (United States)

    Chang, Cheng-Hsiung; Yang, Shang-Shyng

    2009-02-01

    In order to prepare the multi-functional biofertilizer, thermo-tolerant phosphate-solubilizing microbes including bacteria, actinomycetes, and fungi were isolated from different compost plants and biofertilizers. Except Streptomycesthermophilus J57 which lacked pectinase, all isolates possessed amylase, CMCase, chitinase, pectinase, protease, lipase, and nitrogenase activities. All isolates could solubilize calcium phosphate and Israel rock phosphate; various isolates could solubilize aluminum phosphate, iron phosphate, and hydroxyapatite. During composting, biofertilizers inoculated with the tested microbes had a significantly higher temperature, ash content, pH, total nitrogen, soluble phosphorus content, and germination rate than non-inoculated biofertilizer; total organic carbon and carbon-to-nitrogen ratio showed the opposite pattern. Adding these microbes can shorten the period of maturity, improve the quality, increase the soluble phosphorus content, and enhance the populations of phosphate-solubilizing and proteolytic microbes in biofertilizers. Therefore, inoculating thermo-tolerant phosphate-solubilizing microbes into agricultural and animal wastes represents a practical strategy for preparing multi-functional biofertilizer.

  1. Polymeric additives to enhance the functional properties of calcium phosphate cements

    Directory of Open Access Journals (Sweden)

    Roman A Perez

    2012-12-01

    Full Text Available The vast majority of materials used in bone tissue engineering and regenerative medicine are based on calcium phosphates due to their similarity with the mineral phase of natural bone. Among them, calcium phosphate cements, which are composed of a powder and a liquid that are mixed to obtain a moldable paste, are widely used. These calcium phosphate cement pastes can be injected using minimally invasive surgery and adapt to the shape of the defect, resulting in an entangled network of calcium phosphate crystals. Adding an organic phase to the calcium phosphate cement formulation is a very powerful strategy to enhance some of the properties of these materials. Adding some water-soluble biocompatible polymers in the calcium phosphate cement liquid or powder phase improves physicochemical and mechanical properties, such as injectability, cohesion, and toughness. Moreover, adding specific polymers can enhance the biological response and the resorption rate of the material. The goal of this study is to overview the most relevant advances in this field, focusing on the different types of polymers that have been used to enhance specific calcium phosphate cement properties.

  2. Ammonium hexafluorosilicate elicits calcium phosphate precipitation and shows continuous dentin tubule occlusion.

    Science.gov (United States)

    Suge, Toshiyuki; Kawasaki, Akiko; Ishikawa, Kunio; Matsuo, Takashi; Ebisu, Shigeyuki

    2008-02-01

    Diamine silver fluoride [AgF: (NH(3))(2)AgF] has been used clinically in Japan, as it reduces dental caries and dentin hypersensitivity. However, AgF stains the teeth black due to silver precipitation. To overcome this drawback, the authors prepared ammonium hexafluorosilicate [SiF: (NH(4))(2)SiF(6)], which does not stain the teeth, and SiF occluded open dentin tubules completely with silica-calcium phosphate precipitate. The aim of this study was to evaluate the duration of dentin tubule occlusion after SiF treatment in a simulated oral environment. To simulate dentin tubules subject to dentin hypersensitivity, dentin disks were treated with EDTA for 2 min. The disks were treated with 0.476 mol/L SiF for 3 min, and then the disks were immersed in synthetic saliva, which was regularly replenished to maintain its ionic concentration, for up to 7 days. The occluding ability of the dentin tubules was evaluated using scanning electron microscopy (SEM), and the hydraulic conductance was measured following Pashley's method at regular intervals. SEM photographs demonstrated that dentin tubules were occluded homogeneously and completely with the precipitate at 7 days after treatment with SiF. In addition, newly formed calcium phosphate precipitate was present at the dentin surface. The dentin permeability showed a consistently low value throughout the experimental period. The values immediately after SiF treatment and 7 days after immersion were 11.9+/-3.7% and 7.9+/-2.9%, respectively. Ammonium hexafluorosilicate is useful for the treatment of dentin hypersensitivity, since ammonium hexafluorosilicate induced calcium phosphate precipitation from the saliva; therefore, it has a continuous effect on dentin tubules occlusion under a simulated oral environment.

  3. Calcium Phosphate Bone Cements Including Sugar Surfactants: Part One—Porosity, Setting Times and Compressive Strength

    Directory of Open Access Journals (Sweden)

    Juliette Fitremann

    2010-09-01

    Full Text Available Addition of sugar surfactants, sucrose fatty acid esters and alkylpolyglucosides, to calcium phosphate cement designed for bone reconstruction is described. Thanks to their surface activity and through their adsorption at the surface of the calcium phosphate particles, they both induced a strong increase in the porosity (quantified by Image Analysis and brought a very good workability. Other properties typically studied for these cements are reported, including setting times, compressive strength, cohesion in water, and effect of sterilization on these properties. The whole study brought good insight in the interest of adding these mild surfactants to improve several properties of the calcium phosphate cement, without impairing their function.

  4. Structure, properties and animal study of a calcium phosphate/calcium sulfate composite cement.

    Science.gov (United States)

    Chen, Wei-Luen; Chen, Chang-Keng; Lee, Jing-Wei; Lee, Yu-Ling; Ju, Chien-Ping; Lin, Jiin-Huey Chern

    2014-04-01

    In-vitro and in-vivo studies have been conducted on an in-house-developed tetracalcium phosphate (TTCP)/dicalcium phosphate anhydrous (DCPA)/calcium sulfate hemihydrate (CSH)-derived composite cement. Unlike most commercial calcium-based cement pastes, the investigated cement paste can be directly injected into water and harden without dispersion. The viability value of cells incubated with a conditioned medium of cement extraction is >90% that of Al2O3 control and >80% that of blank medium. Histological examination reveals excellent bonding between host bone and cement without interposition of fibrous tissues. At 12 weeks-post implantation, significant remodeling activities are found and a new bone network is developed within the femoral defect. The 26-week samples show that the newly formed bone becomes more mature, while the interface between residual cement and the new bone appears less identifiable. Image analysis indicates that the resorption rate of the present cement is much higher than that of TTCP or TTCP/DCPA-derived cement under similar implantation conditions.

  5. Mechanical and fracture behavior of calcium phosphate cements

    Science.gov (United States)

    Jew, Victoria Chou

    Apatite-based calcium phosphate cements are currently employed to a limited extent in the biomedical and dental fields. They present significant potential for a much broader range of applications, particularly as a bone mineral substitute for fracture fixation. Specifically, hydroxyapatite (HA) is known for its biocompatibility and non-immunogenicity, attributed to its similarity to the mineral phase of natural bone. The advantages of a cement-based HA include injectability, greater resorbability and osteoconductivity compared to sintered HA, and an isothermal cement-forming reaction that avoids necrosis during cement setting. Although apatite cements demonstrate good compressive strength, tensile properties are very weak compared to natural bone. Applications involving normal weight-bearing require better structural integrity than apatite cements currently provide. A more thorough understanding of fracture behavior can elucidate failure mechanisms and is essential for the design of targeted strengthening methods. This study investigated a hydroxyapatite cement using a fracture mechanics approach, focusing on subcritical crack growth properties. Subcritical crack growth can lead to much lower load-bearing ability than critical strength values predict. Experiments show that HA cement is susceptible to crack growth under both cyclic fatigue-crack growth and stress corrosion cracking conditions, but only environmental, not mechanical, mechanisms contribute to crack extension. This appears to be the first evidence ever presented of stress corrosion crack growth behavior in calcium phosphate cements. Stress corrosion cracking was examined for a range of environmental conditions. Variations in pH have surprisingly little effect. Behavior in water at elevated temperature (50°C) is altered compared to water at ambient temperature (22°C), but only for crack-growth velocities below 10-7 m/s. However, fracture resistance of dried HA cement in air increases significantly

  6. Novel rechargeable calcium phosphate nanoparticle-containing orthodontic cement.

    Science.gov (United States)

    Xie, Xian-Ju; Xing, Dan; Wang, Lin; Zhou, Han; Weir, Michael D; Bai, Yu-Xing; Xu, Hockin Hk

    2016-11-04

    White spot lesions (WSLs), due to enamel demineralization, occur frequently in orthodontic treatment. We recently developed a novel rechargeable dental composite containing nanoparticles of amorphous calcium phosphate (NACP) with long-term calcium (Ca) and phosphate (P) ion release and caries-inhibiting capability. The objectives of this study were to develop the first NACP-rechargeable orthodontic cement and investigate the effects of recharge duration and frequency on the efficacy of ion re-release. The rechargeable cement consisted of pyromellitic glycerol dimethacrylate (PMGDM) and ethoxylated bisphenol A dimethacrylate (EBPADMA). NACP was mixed into the resin at 40% by mass. Specimens were tested for orthodontic bracket shear bond strength (SBS) to enamel, Ca and P ion initial release, recharge and re-release. The new orthodontic cement exhibited an SBS similar to commercial orthodontic cement without CaP release (P>0.1). Specimens after one recharge treatment (e.g., 1 min immersion in recharge solution repeating three times in one day, referred to as "1 min 3 times") exhibited a substantial and continuous re-release of Ca and P ions for 14 days without further recharge. The ion re-release did not decrease with increasing the number of recharge/re-release cycles (P>0.1). The ion re-release concentrations at 14 days versus various recharge treatments were as follows: 1 min 3 times>3 min 2 times>1 min 2 times>6 min 1 time>3 min 1 time>1 min 1 time. In conclusion, although previous studies have shown that NACP nanocomposite remineralized tooth lesions and inhibited caries, the present study developed the first orthodontic cement with Ca and P ion recharge and long-term release capability. This NACP-rechargeable orthodontic cement is a promising therapy to inhibit enamel demineralization and WSLs around orthodontic brackets.International Journal of Oral Science advance online publication,4 November 2016; doi:10.1038/ijos.2016.40.

  7. Pressure effects on the interactions of the sarcoplasmic reticulum calcium transport enzyme with calcium and dinitrophenyl phosphate.

    Science.gov (United States)

    Hasselbach, W

    1988-01-01

    The effect of hydrostatic pressure on the calcium-dependent hydrolysis of dinitrophenyl phosphate by the sarcoplasmic calcium transport enzyme has been studied. The magnesium dinitrophenyl phosphate complex is the true substrate of the enzyme (K = 7000 M-1) by which it is hydrolyzed at 20 degrees C with a turnover rate of 4 s-1. Activation by calcium ions occurs between 0.1 and 1 microM as observed for ATP hydrolysis. The activation volume of the enzyme saturated with both ligands exhibits pronounced pressure-dependence, rising from 25 ml/mol at atmospheric pressure to 80 ml/mol at 100 MPa. The apparent binding volumes for magnesium dinitrophenyl phosphate and calcium are likewise pressure-dependent. The volume changes connected with the binding of magnesium dinitrophenyl phosphate is quite small approaching zero at 100 MPa. The apparent binding volume for calcium greatly increases with pressure from 35 ml/mol at atmospheric pressure to 150 ml/mol at 70 MPa. A nearly constant binding volume of approximately 40 ml/mol results if the effect of pressure on the respective rate constants that contribute to the apparent binding constant, is taken into account. The pressure-dependence of enzyme activity at subsaturating calcium concentrations yields an activation volume of 250 ml/mol related to the rate of calcium binding indicating the occurrence of a transient large volume expansion of the enzyme complex. The volume changes observed for the calcium-dependent interaction of the enzyme with magnesium dinitrophenyl phosphate well agree with that found for magnesium p-nitrophenyl phosphate (W. Hasselbach and L. Stephan,Z. Naturforsch. 42 c, 641-652 (1987)) indicating that the found volume changes are intrinsic properties of the transport enzyme, independent of the respective energy donor.(ABSTRACT TRUNCATED AT 250 WORDS)

  8. In vitro study on biomineralization of biphasic calcium phosphate biocomposite crosslinked with hydrolysable tannins of Terminalia chebula

    Indian Academy of Sciences (India)

    G Krithiga; Antaryami Jena; P Selvamani; T P Sastry

    2011-06-01

    In this study, we report the preparation of a bone graft material, having cylindrical shape, containing biphasic calcium phosphate (BCP), gelatin (G), chitosan (C) and Terminalia chebula (TC) extract. TC extract was used as a crosslinker that gives stability to bone graft when it is placed in SBF. The graft was stable in the SBF solution for 21 days and FTIR, SEM, EDX and thermogravimetric studies revealed the ossification of the implant.

  9. The Effect of Calcium Phosphate Particle Shape and Size on their Antibacterial and Osteogenic Activity in the Delivery of Antibiotics in vitro

    Science.gov (United States)

    Uskoković, Vuk; Batarni, Samir Shariff; Schweicher, Julien; King, Andrew; Desai, Tejal A.

    2013-01-01

    Powders composed of four morphologically different calcium phosphate particles were prepared by precipitation from aqueous solutions: flaky, brick-like, elongated orthogonal, and spherical. The particles were then loaded with either clindamycin phosphate as the antibiotic of choice, or fluorescein, a model molecule used to assess the drug release properties. A comparison was carried out of the comparative effect of such antibiotic-releasing materials on: sustained drug release profiles; Staphylococcus aureus growth inhibition; and osteogenic propensities in vitro. Raman spectroscopic analysis indicated the presence of various calcium phosphate phases, including monetite (flaky and elongated orthogonal particles), octacalcium phosphate (brick-shaped particles) and hydroxyapatite (spherical particles). Testing the antibiotic-loaded calcium phosphate powders for bacterial growth inhibition demonstrated satisfying antibacterial properties both in broths and on agar plates. All four calcium-phosphate-fluorescein powders exhibited sustained drug release over 21 days. The calcium phosphate sample with the highest specific surface area and the smallest, spherical particle size was the most effective in both drug loading and release, consequently having the highest antibacterial efficiency. Moreover, the highest cell viability, the largest gene expression upregulation of three different osteogenic markers – osteocalcin, osteopontin and Runx2 - as well as the least disrupted cell cytoskeleton and cell morphologies were also noticed for the calcium phosphate powder composed of smallest, spherical nanosized particles. Still, all four powders exerted a viable effect on osteoblastic MC3T3-E1 cells in vitro, as evidenced by both morphological assessments on fluorescently stained cells and measurements of their mitochondrial activity. The obtained results suggest that the nanoscale particle size and the corresponding coarseness of the surface of particle conglomerates as the

  10. Synthesis of spherical calcium phosphate particles for dental and orthopedic applications.

    Science.gov (United States)

    Bohner, Marc; Tadier, Solène; van Garderen, Noémie; de Gasparo, Alex; Döbelin, Nicola; Baroud, Gamal

    2013-01-01

    Calcium phosphate materials have been used increasingly in the past 40 years as bone graft substitutes in the dental and orthopedic fields. Accordingly, numerous fabrication methods have been proposed and used. However, the controlled production of spherical calcium phosphate particles remains a challenge. Since such particles are essential for the synthesis of pastes and cements delivered into the host bone by minimally-invasive approaches, the aim of the present document is to review their synthesis and applications. For that purpose, production methods were classified according to the used reagents (solutions, slurries, pastes, powders), dispersion media (gas, liquid, solid), dispersion tools (nozzle, propeller, sieve, mold), particle diameters of the end product (from 10 nm to 10 mm), and calcium phosphate phases. Low-temperature calcium phosphates such as monetite, brushite or octacalcium phosphate, as well as high-temperature calcium phosphates, such as hydroxyapatite, β-tricalcium phosphate or tetracalcium phosphate, were considered. More than a dozen production methods and over hundred scientific publications were discussed.

  11. Synthesis of spherical calcium phosphate particles for dental and orthopedic applications

    Science.gov (United States)

    Bohner, Marc; Tadier, Solène; van Garderen, Noémie; de Gasparo, Alex; Döbelin, Nicola; Baroud, Gamal

    2013-01-01

    Calcium phosphate materials have been used increasingly in the past 40 years as bone graft substitutes in the dental and orthopedic fields. Accordingly, numerous fabrication methods have been proposed and used. However, the controlled production of spherical calcium phosphate particles remains a challenge. Since such particles are essential for the synthesis of pastes and cements delivered into the host bone by minimally-invasive approaches, the aim of the present document is to review their synthesis and applications. For that purpose, production methods were classified according to the used reagents (solutions, slurries, pastes, powders), dispersion media (gas, liquid, solid), dispersion tools (nozzle, propeller, sieve, mold), particle diameters of the end product (from 10 nm to 10 mm), and calcium phosphate phases. Low-temperature calcium phosphates such as monetite, brushite or octacalcium phosphate, as well as high-temperature calcium phosphates, such as hydroxyapatite, β-tricalcium phosphate or tetracalcium phosphate, were considered. More than a dozen production methods and over hundred scientific publications were discussed. PMID:23719177

  12. A histological evaluation on osteogenesis and resorption of methotrexate-loaded calcium phosphate cement in vivo

    Energy Technology Data Exchange (ETDEWEB)

    Li Dong; Yang Zhiping; Li Xin; Li Zhenfeng; Li Jianmin [Department of Orthopedics, Qilu Hospital of Shandong University, Shandong (China); Yang Jingyan, E-mail: yangzhiping@medmail.com.c [Department of Pathology, 2nd Affiliated Hospital of Shandong University, Shandong (China)

    2010-04-15

    In this study, we investigated the resorption of in vivo methotrexate-loaded calcium phosphate cement (MTX-CPC) implants and their effect on osteogenesis. MTX-CPC implants containing 1% methotrexate (MTX) (weight/weight) were preset and implanted into the femoral condyle of rabbits. Calcium phosphate cement (CPC) without MTX was used as the control. The femurs were harvested at day 1 and at 1, 3 and 6 months after implantation and radiological examination were performed. Decalcified sections were examined by hematoxylin and eosin (HE) staining, alkaline phosphatase (ALPase) immunohistochemistry and tartrate-resistant acid phosphatase (TRAPase) enzyme histochemistry. Then, we performed histomorphometric analysis, including determination of the percentage of newly formed bone and osteoblast and osteoclast counts. The results indicated that MTX-CPC implants were biocompatible, biodegradable and osteoconducive. However, MTX release from the implantation site inhibited osteogenesis in the initial period; this inhibition weakened with time, and no difference was observed between CPC and MTX-CPC at 6 months after implantation. Hence, MTX-CPC is an excellent material for filling defects and can be used for preparing effective drug delivery systems to achieve local control of invasive bone tumors.

  13. Osteogenic activity of cyclodextrin-encapsulated doxycycline in a calcium phosphate PCL and PLGA composite.

    Science.gov (United States)

    Trajano, V C C; Costa, K J R; Lanza, C R M; Sinisterra, R D; Cortés, M E

    2016-07-01

    Composites of biodegradable polymers and calcium phosphate are bioactive and flexible, and have been proposed for use in tissue engineering and bone regeneration. When associated with the broad-spectrum antibiotic doxycycline (DOX), they could favor antimicrobial action and enhance the action of osteogenic composites. Composites of polycaprolactone (PCL), poly(lactic-co-glycolic acid) (PLGA), and a bioceramic of biphasic calcium phosphate Osteosynt® (BCP) were loaded with DOX encapsulated in β-cyclodextrin (βCD) and were evaluated for effects on osteoblastic cell cultures. The DOX/βCD composite was prepared with a double mixing method. Osteoblast viability was assessed with methyl tetrazolium (MTT) assays after 1day, 7day, and 14days of composite exposure; alkaline phosphatase (AP) activity and collagen production were evaluated after 7days and 14days, and mineral nodule formation after 14days. Composite structures were evaluated by scanning electron microscopy (SEM). Osteoblasts exposed to the composite containing 25μg/mL DOX/βCD had increased cell proliferation (pcomposite (pcomposite material revealed a surface topography with pore sizes suitable for growing osteoblasts. Together, these results suggest that osteoblasts are viable, proliferative, and osteogenic in the presence of a DOX/βCD-containing BCP ceramic composite.

  14. Bioactive calcium sulfate/magnesium phosphate cement for bone substitute applications

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Guangyong [Department of Orthopaedics, Taizhou Hospital of Zhejiang Province, Linhai Zhejiang, 317000 (China); Department of Orthopaedic Surgery, Second Affiliated Hospital of Wenzhou Medical College, Wenzhou, Zhejiang, 325000 (China); Liu, Jianli [Trauma Center, Affiliated Hospital of Hainan Medical University, Haikou, Hainan, 570206 (China); Division of Functional Materials and Nanodevices, Ningbo Institute of Materials Technology and Engineering (NIMTE), Chinese Academy of Sciences (CAS), Ningbo, Zhejiang, 315201 (China); Li, Fan; Pan, Zongyou; Ni, Xiao; Shen, Yue [Department of Orthopaedic Surgery, Second Affiliated Hospital of Wenzhou Medical College, Wenzhou, Zhejiang, 325000 (China); Xu, Huazi, E-mail: spinexu@163.com [Department of Orthopaedic Surgery, Second Affiliated Hospital of Wenzhou Medical College, Wenzhou, Zhejiang, 325000 (China); Huang, Qing, E-mail: huangqing@nimte.ac.cn [Division of Functional Materials and Nanodevices, Ningbo Institute of Materials Technology and Engineering (NIMTE), Chinese Academy of Sciences (CAS), Ningbo, Zhejiang, 315201 (China)

    2014-02-01

    A novel calcium sulfate/magnesium phosphate cement (CSMPC) composite was prepared and studied in the present work. The physical properties including the phases, the microstructures, the setting properties and the compressive strengths of the CSMPCs were studied. The bio-performances of the CSMPCs were comprehensively evaluated using in vitro simulated body fluid (SBF) method and in vitro cell culture. The dependence of the physical and chemical properties of the CSMPC on its composition and microstructure was studied in detail. It is found that the CSMPC composites exhibited mediate setting times (6–12 min) compared to the calcium sulfate (CS) and the magnesium phosphate cement (MPC). They showed an encapsulation structure in which the unconverted hexagonal prism CSH particles were embedded in the xerogel-like MPC matrix. The phase compositions and the mechanical properties of the CSMPCs were closely related to the content of MPC and the hardening process. The CSMPCs exhibited excellent bioactivity and good biocompatibility to support the cells to attach and proliferate on the surface. The CSMPC composite has the potential to serve as bone grafts for the bone regeneration. - Highlights: • The mechanical strength and degradation rate of CSMPC composites are discussed. • The CSMPC composites exhibited good bioactivity to form bone-like apatite. • The CSMPC composites also show good biocompatibility.

  15. Bioactive calcium sulfate/magnesium phosphate cement for bone substitute applications.

    Science.gov (United States)

    Yang, Guangyong; Liu, Jianli; Li, Fan; Pan, Zongyou; Ni, Xiao; Shen, Yue; Xu, Huazi; Huang, Qing

    2014-02-01

    A novel calcium sulfate/magnesium phosphate cement (CSMPC) composite was prepared and studied in the present work. The physical properties including the phases, the microstructures, the setting properties and the compressive strengths of the CSMPCs were studied. The bio-performances of the CSMPCs were comprehensively evaluated using in vitro simulated body fluid (SBF) method and in vitro cell culture. The dependence of the physical and chemical properties of the CSMPC on its composition and microstructure was studied in detail. It is found that the CSMPC composites exhibited mediate setting times (6-12 min) compared to the calcium sulfate (CS) and the magnesium phosphate cement (MPC). They showed an encapsulation structure in which the unconverted hexagonal prism CSH particles were embedded in the xerogel-like MPC matrix. The phase compositions and the mechanical properties of the CSMPCs were closely related to the content of MPC and the hardening process. The CSMPCs exhibited excellent bioactivity and good biocompatibility to support the cells to attach and proliferate on the surface. The CSMPC composite has the potential to serve as bone grafts for the bone regeneration.

  16. Chlorhexidine-calcium phosphate nanoparticles - Polymer mixer based wound healing cream and their applications.

    Science.gov (United States)

    Viswanathan, Kaliyaperumal; Monisha, P; Srinivasan, M; Swathi, D; Raman, M; Dhinakar Raj, G

    2016-10-01

    In this work, we developed a wound healing cream composed of two different polymers, namely chitosan and gelatin with chlorhexidine along with calcium phosphate nanoparticles. The physicochemical properties of the prepared cream were investigated based on SEM, EDX, Raman, FTIR and the results indicated that the cream contained gelatin, chitosan, calcium phosphate nanoparticles and chlorhexidine. The maximum swelling ratio studies indicated that the ratio was around of 52±2.2 at pH7.4 and the value was increased in acidic and alkaline pH. The antimicrobial activity was tested against bacteria and the results indicated that, both chlorhexidine and the hybrid cream devoid of chlorhexidine exhibited antimicrobial activity but the chlorhexidine impregnated cream showed three fold higher antimicrobial activity than without chlorhexidine. In vivo wound healing promoting activities of hybrid cream containing 0.4mg/L chlorhexidine were evaluated on surgically induced dermal wounds in mice. The results indicated that the cream with incorporated chlorhexidine significantly enhanced healing compared with the control samples. For the field validations, the veterinary clinical animals were treated with the cream and showed enhanced healing capacity. In conclusion, a simple and efficient method for design of a novel wound healing cream has been developed for veterinary applications.

  17. Uptake of the proteins HTRA1 and HTRA2 by cells mediated by calcium phosphate nanoparticles

    Science.gov (United States)

    Rotan, Olga; Severin, Katharina N; Pöpsel, Simon; Peetsch, Alexander; Merdanovic, Melisa; Ehrmann, Michael

    2017-01-01

    The efficient intracellular delivery of (bio)molecules into living cells remains a challenge in biomedicine. Many biomolecules and synthetic drugs are not able to cross the cell membrane, which is a problem if an intracellular mode of action is desired, for example, with a nuclear receptor. Calcium phosphate nanoparticles can serve as carriers for small and large biomolecules as well as for synthetic compounds. The nanoparticles were prepared and colloidally stabilized with either polyethyleneimine (PEI; cationic nanoparticles) or carboxymethyl cellulose (CMC; anionic nanoparticles) and loaded with defined amounts of the fluorescently labelled proteins HTRA1, HTRA2, and BSA. The nanoparticles were purified by ultracentrifugation and characterized by dynamic light scattering and scanning electron microscopy. Various cell types (HeLa, MG-63, THP-1, and hMSC) were incubated with fluorescently labelled proteins alone or with protein-loaded cationic and anionic nanoparticles. The cellular uptake was followed by light and fluorescence microscopy, confocal laser scanning microscopy (CLSM), and flow cytometry. All proteins were readily transported into the cells by cationic calcium phosphate nanoparticles. Notably, only HTRA1 was able to penetrate the cell membrane of MG-63 cells in dissolved form. However, the application of endocytosis inhibitors revealed that the uptake pathway was different for dissolved HTRA1 and HTRA1-loaded nanoparticles. PMID:28326227

  18. The influence of magnetism on precipitation of calcium phosphate

    Science.gov (United States)

    Skytte Sørensen, Jens; Lundager Madsen, Hans E.

    2000-06-01

    The precipitation of calcium phosphate upon rapid mixing of solutions of CaCl 2 and KH 2PO 4-K 2HPO 4 was followed by pH and other quantitative measurements and the examination of the precipitate in the polarizing microscope. The experiments were carried out at 25°C in the presence and absence of a static magnetic field of 0.27 T. It was found that the magnetic field increased dissolution of metastable precursor phases and increased nucleation of more stable phases. This was a general tendency for the transformation sequence: ACP→ brushite →OCP→HAP at initial pH≈6.5 and total concentrations CCa= CP=25, 50 or 100 mM. Crystallization upon slow diffusion of ions from a solution of CaCl 2 into silica hydrogel containing dissolved KH 2PO 4-K 2HPO 4 was followed by recording the number and positions of appearing brushite crystals and Liesegang rings. The experiment was performed in the presence and absence of magnetic fields in the range 0.08-0.3 T and the following conditions: room temperature, initial pH of the gel between 5.5 and 6.8, and CCa= CP=50 mM. Magnetism increased nucleation of brushite in the experiments at low initial pH. The dependence on field strength was not significant, and no effect was found in experiments with high initial pH.

  19. Structure and properties of silver-doped calcium phosphate nanopowders

    Indian Academy of Sciences (India)

    RAVINDER PAL SINGH; UMA BATRA

    2016-09-01

    Stable and antimicrobial silver-doped calcium phosphate nanopowders were synthesized using sol–gel route by setting the atomic ratio of Ag/(Ag +Ca) at 3%and (Ca $+$ Ag)/P at 1.67. Prior to synthesis of nanopowders, influence of time of hydrolyzation on pH and density of precursors were comprehensively studied. Hydrolyzation time was found to have profound influence on pH of constituent precursors. Sufficient hydrolysis resulted in early maturation of sol. Scanning electron microscopy (SEM) showed the heterogeneous and agglomerated state of particles with average size of $3.9\\pm 1.9$ $\\mu$m. Energy dispersive X-ray spectroscopy (EDX) presented uniform distributionof O, Ag, Ca and P elements in nanopowder. Fourier transform infrared spectroscopy (FTIR) confirmed the formation of apatitic structure, whereas X-ray diffraction (XRD) revealed the multiphase constitution of nanopowdersprimarily composed of $\\beta$-TCP, Ag and other hybrid phases. Crystallite size and lattice parameters of $\\beta$-TCP and Ag phases were increased with the rise in calcination temperature. Thermogravimetric analysis (TGA) showed threeregions of weight change and indicated the high thermal stability of nanopowders. Disk diffusion method was used to test the antimicrobial resistance of nanopowders against Escherichia coli and Staphylococcus aureus bacterial strains. All nanopowders exhibited antimicrobial resistance against both E. coli and S. aureus bacteria.

  20. Initial Stability Study of Calcium Phosphate Coated Dental Implants

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Thin film of biodegradable calcium phosphate coated on threaded commercially pure titanium( cp- Ti) dental implants has been investigated as one of alternatives to eliminate the problem of the long-term instability of plasma sprayed HA coated implants. In order to compare in-vivo hone-to-implant response behavior among as-machined, HA coated and CMP coated groups, each group was implanted into New Zealand white mature male rabbits for 2 and 6 weeks, and then in- vivo biological behavior was examined in terms of H&E staining. Initial stability and removable torques of implants were compared among three groups. Measured removable torque of CMP coated specimen at 6 wceks after implantation was significantly higher than that of non-coated group, but slightly lower than that of HA coated group, without any inflammatory response at the surrounding of the implants. The initial stability (ISQ value; implant stability quotient ) of CMP coated specimen at 2 weeks after implantation was slightly lower than that of HA coated group and significantly higher than that of non-coated group. However, after 6 weeks, ISQ value of CMP coated group was slightly higher than that of HA coated group and significantly higher than that of non-coated group.

  1. Calcium phosphates in biomedical applications: materials for the future?

    Directory of Open Access Journals (Sweden)

    Wouter Habraken

    2016-03-01

    Full Text Available Our populations are aging. Some experts predict that 30% of hospital beds will soon be occupied by osteoporosis patients. Statistics show that 20% of patients suffering from an osteoporotic hip fracture do not survive the first year after surgery, all this showing that there is a tremendous need for better therapies for diseased and damaged bone. Human bone consists for about 70% of calcium phosphate (CaP mineral, therefore CaPs are the materials of choice to repair damaged bone. To do this successfully, the process of CaP biomineralization and the interaction of CaPs and biological environment in the body need to be fully understood. First commercial CaP bone graft substitutes were launched 40 years ago, and they are currently often regarded as ‘old biomaterials’ or even as an ‘obsolete’ research topic. Some even talk about ‘stones’. The aim of this manuscript is to highlight the tremendous improvements achieved in CaP materials research in the past 15 years, in particular in the field of biomineralization, as carrier for gene or ion delivery, as biologically active agent, and as bone graft substitute. Besides an outstanding biological performance, CaPs are easily and inexpensively produced, are safe, and can be relatively easily certified for clinical use. As such, CaP materials have won their spurs, but they also offer a great promise for the future.

  2. A randomised study to compare salivary pH, calcium, phosphate and calculus formation after using anticavity dentifrices containing Recaldent(®) and functionalized tri-calcium phosphate.

    Science.gov (United States)

    Sharma, Ena; Vishwanathamurthy, Ramesh Alampalli; Nadella, Manjari; Savitha, A N; Gundannavar, Gayatri; Hussain, M Ahad

    2012-10-01

    The aim of this study was to estimate the pH of saliva, concentration of calcium and inorganic phosphate, and calculus formation before and after usage of Recaldent(®) (GC Tooth Mousse Plus™), Functionalized Tricalcium Phosphate (3M ESPE ClinPro™ Tooth Crème) and standard dentifrice (Colgate dental cream). Randomized double-blind study. A total of 50 subjects were recruited, the subjects were assessed at their first visit, on the 21(st) day and on the 42(nd) day. At the first visit, scaling was carried out and oral hygiene instructions were given. After 21 days, the subjects were given coded dentifrices where the operator and the subjects both were unaware of the type of dentifrice. Clinical parameters assessed were Plaque index, Gingival index, and Calculus index. Salivary samples were obtained to measure calcium, phosphate levels, and pH at 21(st) day and 42(nd) day. ANOVA test, t-test, Mann-Whitney test, Kruskal-Wallis test. The mean salivary calcium level and mean salivary phosphate level were higher in Group III (functionalized tricalcium phosphate (3M ESPE ClinPro™ Tooth Creme) as compared to Group II (Recaldent(®) GC Tooth Mousse Plus™) and Group I (Colgate dental cream) on the 42(nd) day after using dentifrices, which was statistically significant. This showed that the usage of remineralizing dentifrices led to an increase in the salivary calcium, phosphate, and pH but it did not reach the level of super saturation of the ions caused by elevated pH which could lead to calculus formation. Thought here was a statistically significant increase in salivary calcium and phosphate level in all three groups from baseline to 42(nd) day, there was no calculus formation.

  3. Study of hMSC proliferation and differentiation on Mg and Mg–Sr containing biphasic β-tricalcium phosphate and amorphous calcium phosphate ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Satish S., E-mail: sss42@pitt.edu [Department of Chemical & Petroleum Engineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Roy, Abhijit, E-mail: abr20@pitt.edu [Department of Bioengineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Lee, Boeun [Department of Bioengineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Kumta, Prashant N., E-mail: pkumta@pitt.edu [Department of Chemical & Petroleum Engineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Department of Bioengineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Center for Craniofacial Regeneration, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Department of Mechanical Engineering and Materials Science, University of Pittsburgh, PA 15261 (United States)

    2016-07-01

    Biphasic mixtures of either Mg{sup 2+} or combined Mg{sup 2+} and Sr{sup 2+} cation substituted β-tricalcium phosphate (β-TCP) and amorphous calcium phosphate (ACP) were prepared using a low temperature chemical phosphatizing and hydrolysis reaction approach. Scaffolds prepared using the cation substituted calcium phosphates were capable of supporting similar levels of human mesenchymal stem cell proliferation in comparison to commercially available β-TCP. The concentrations of Mg{sup 2+}, Sr{sup 2+}, and PO{sub 4}{sup 3−} released from these scaffolds were also within the ranges desired from previous reports to support both hMSC proliferation and osteogenic differentiation. Interestingly, hMSCs cultured directly on scaffolds prepared with only Mg{sup 2+} substituted β-TCP were capable of supporting statistically significantly increased alkaline phosphatase activity, osteopontin, and osteoprotegerin expression in comparison to all compositions containing both Mg{sup 2+} and Sr{sup 2+}, and commercially available β-TCP. hMSCs cultured in the presence of scaffold extracts also exhibited similar trends in the expression of osteogenic markers as was observed during direct culture. Therefore, it was concluded that the enhanced differentiation observed was due to the release of bioactive ions rather than the surface microstructure. The role of these ions on transforming growth factor-β and bone morphogenic protein signaling was also evaluated using a PCR array. It was concluded that the release of these ions may support enhanced differentiation through SMAD dependent TGF-β and BMP signaling. - Highlights: • Synthesis of Mg and Mg-Sr containing biphasic beta tricalcium phosphate ceramics • Magnesium substitution influences ALP activity compared to strontium content. • Solution extract plays a more dominant role on hMSC differentiation. • Direct and indirect Mg and Mg-Sr TCP culture show similar OPG and OPN expression.

  4. Towards understanding biomineralization:calcium phosphate in a biomimetic minerallzation process

    Institute of Scientific and Technical Information of China (English)

    Yu-rong CAI; Rui-kang TANG

    2009-01-01

    Biomineralization processes result in organic/inorganic hybrid materials with complex shapes,hiemrchi-cal structures.and superior matefial properties. Recent developments in biominemlization and biomatarials have demonstrated that calcium phosphate particles play an important role in the formation of hard tissues in nature. In this paper,current concepts in biominemlization,such as nano assembly,biomimetic shell structure,and their applications are introduced. It is confirmed experimentally that enamel-or bone-liked apatita can be achieved by oriented aggregations using nano calcium phosphates as starting matarials. The assembly of calcium phosphate can be either promoted or inhibited by diflerent biomolecules so that the kinetics can he regulated biologically.In this paper,the role of nano calcium phosphate in tissue repair is highligllted Furthermore,a new,interesting result on biomimetie mineralization 1s Introduced,which can offer an artificial shell for living cells via a biomimatic method .

  5. Characterization of a silver-incorporated calcium phosphate film by RBS and its antimicrobial effects

    Energy Technology Data Exchange (ETDEWEB)

    Han, I-H [Institute of Physics and Applied Physics, and Atomic-Scale Surface Science Research Center, Yonsei University, Seou1 120-749 (Korea, Republic of); Lee, I-S [Institute of Physics and Applied Physics, and Atomic-Scale Surface Science Research Center, Yonsei University, Seou1 120-749 (Korea, Republic of); Song, J-H [Advanced Analysis Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Lee, M-H [Department of Medical Engineering, Yonsei University, Seoul 120-752 (Korea, Republic of); Park, J-C [Department of Medical Engineering, Yonsei University, Seoul 120-752 (Korea, Republic of); Lee, G-H [Korea Institute of Machinery and Materials, Chang-Won 641-010 (Korea, Republic of); Sun, X-D [Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Chung, S-M [Implantium Research Center, Seoul 135-879 (Korea, Republic of)

    2007-09-15

    A thin calcium phosphate film was synthesized on both commercially pure Ti and Si wafers by electron beam evaporation of hydroxyapatite as an evaporant with simultaneous Ar ion beam bombardments. Silver was introduced into an ion-beam-assisted deposition of a calcium phosphate thin film for antimicrobial effect. The amount of incorporated silver ions was controlled by immersing calcium-phosphate-coated samples in different AgNO{sub 3} concentrations, and Rutherford backscattering spectrometry (RBS) was employed to measure the amounts of substituted silver. The higher concentration of silver in the calcium phosphate film was more effective in reducing the bacteria of Escherichia coli ATCC 8739 and Streptococcus mutans OMZ 65 on contact with respect to controls.

  6. Reflections on the Mechanism of Calcium Phosphate Nucleation on Titanium in Simulated Body Fluids

    Institute of Scientific and Technical Information of China (English)

    F. T. Cheng

    2005-01-01

    The results and main findings of studies reported in the literature in relation to the deposition of calcium phosphate on Ti in simulated body fluids are summarized. The effects of the surface hydroxyl groups and the sign of surface charge on the nucleation of calcium phosphate are reviewed. One major controversy among the conclusions of different studies is the order of adsorption of the calcium ions and the phosphate ions in the initial stage of immersion. A simple model based on the amphoteric nature of the hydroxyl groups on Ti is proposed in an attempt to delineate the nucleation process for calcium phosphate on Ti in simulated body fluids. HPO42- ions interact with the hydroxyl groups via ion exchange and/or electrostatic attraction, and Ca2+ ions, via electrostatic attraction only. There is no preferential order of adsorption. Seemingly inconsistent results in different studies possibly arise from different prior treatments of the samples, which affect the adsorption properties.

  7. Synthesis of nanocrystalline calcium phosphate in microemulsion--effect of nature of surfactants.

    Science.gov (United States)

    Singh, Sujata; Bhardwaj, Pallavi; Singh, V; Aggarwal, S; Mandal, U K

    2008-03-01

    Nanosized calcium phosphate (CP) powders have been synthesized by an inverse microemulsion system using kerosene as the oil phase, a cationic surfactant Aliquat 336, a non-ionic surfactant Tween 20 and their mixture and aqueous solutions of calcium nitrate tetrahydrate and biammonium hydrogen phosphate as the water phase. It has been found that the nature of surfactants played an important role to regulate the size and morphologies of the calcium phosphate nanoparticles. The cationic surfactant Aliquat 336 has been found to regulate the nucleation and crystal growth. The synthesized powders have been comprehensively characterized using transmission electron microscopy (TEM), scanning electron microscopy (SEM), powder X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). Our results show that the brushite (DCPD) is the major phase comprising the calcium phosphate nanoparticles. In mixed surfactants mediated system a morphological controlled highly crystalline particles have been synthesized. Further, the role of Aliquat 336 has been established and a plausible synthetic mechanism has been proposed.

  8. Gelation and biocompatibility of injectable alginate-calcium phosphate gels for bone regeneration

    NARCIS (Netherlands)

    Cardoso, D.A.; Beucken, J.J.J.P van den; Both, L.L.; Bender, J.; Jansen, J.A.; Leeuwenburgh, S.C.G.

    2014-01-01

    An emerging approach toward development of injectable, self-setting, and fully biodegradable bone substitutes involves the combination of injectable hydrogel matrices with a dispersed phase consisting of nanosized calcium phosphate particles. Here, novel injectable composites for bone regeneration h

  9. Evaluation of Calcium Phosphate Cement As a Root Canal Sealer Filling Material

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Calcium phosphate cement for root end sealing was obtained by mixing α-tricalcium phosphate and additives with an aqueous solution of citric. Powder and liquid were mixed at a ratio of 1.25g/mL. The biocompatibility of this material was investigated primarily by subcutaneous implantation tests. Then calcium phosphate cement was used to fill three adult dogs' root canal, both calcium hydroxide paste and hydroxyapatite paste as control. The animals were killed at 4,12,20 weeks postoperatively respectively. The effects of different materials on the apical closure, restoration of periapical tissues and adaptability to the dentinal surface were examined by optical and electronic microscope. The observation at 20 weeks shows that the calcium phosphate cement has the potentialities of being a root canal sealer filling material available for pulpless teeth with open-apex and destructive periapical tissue.

  10. Balloon vetebroplasty with calcium phosphate cement augmentation for direct restoration of traumatic thoracolumbar vertebral fractures

    NARCIS (Netherlands)

    Verlaan, JJ; van Helden, WH; Oner, FC; Verbout, AJ; Dhert, WJA

    2002-01-01

    Study Design. A human cadaveric model was used to evaluate balloon vertebroplasty in traumatic vertebral fractures. Objectives. To assess the feasibility and safety of balloon vertebroplasty followed by calcium phosphate cement augmentation to prevent recurrent kyphosis. Summary of Background Data.

  11. Balloon vetebroplasty with calcium phosphate cement augmentation for direct restoration of traumatic thoracolumbar vertebral fractures

    NARCIS (Netherlands)

    Verlaan, JJ; van Helden, WH; Oner, FC; Verbout, AJ; Dhert, WJA

    2002-01-01

    Study Design. A human cadaveric model was used to evaluate balloon vertebroplasty in traumatic vertebral fractures. Objectives. To assess the feasibility and safety of balloon vertebroplasty followed by calcium phosphate cement augmentation to prevent recurrent kyphosis. Summary of Background Data.

  12. Relationship between Salivary Alkaline Phosphatase Enzyme Activity and The Concentrations of Salivary Calcium and Phosphate Ions

    Directory of Open Access Journals (Sweden)

    Mina Jazaeri

    2015-04-01

    Full Text Available Although salivary alkaline phosphatase (ALP can balance de- and remineralization processes of enamel, there is no evidence regarding its effects on the concentrations of calcium and phosphate in saliva. The present study aims to determine the relationship between salivary ALP activity and the concentrations of calcium and phosphate in saliva. In this cross-sectional study, we evaluated salivary markers in 120 males, ages 19 to 44 years. All participants provided 5 mL of unstimulated whole saliva and the level of enzyme activity as well as calcium and phosphate concentrations were measured using a colorimetric method. Data were gathered and analyzed by statistical package for social sciences (SPSS 13.00 using Pearson correlation test. A p value of 0.05. According to the results of the present study, there was no significant relation between salivary ALP activity and calcium and phosphate concentrations in saliva. However, further research is highly recommended.

  13. Randomized crossover study comparing the phosphate-binding efficacy of calcium ketoglutarate versus calcium carbonate in patients on chronic hemodialysis.

    Science.gov (United States)

    Bro, S; Rasmussen, R A; Handberg, J; Olgaard, K; Feldt-Rasmussen, B

    1998-02-01

    The objective of the study was to evaluate the phosphate-binding efficacy, side effects, and cost of therapy of calcium ketoglutarate granulate as compared with calcium carbonate tablets in patients on chronic hemodialysis. The study design used was a randomized, crossover open trial, and the main outcome measurements were plasma ionized calcium levels, plasma phosphate levels, plasma intact parathyroid hormone (PTH) levels, requirements for supplemental aluminum-aminoacetate therapy, patient tolerance, and cost of therapy. Nineteen patients on chronic hemodialysis were treated with a dialysate calcium concentration of 1.25 mmol/L and a fixed alfacalcidol dose for at least 2 months. All had previously tolerated therapy with calcium carbonate. Of the 19 patients included, 10 completed both treatment arms. After 12 weeks of therapy, the mean (+/-SEM) plasma ionized calcium level was significantly lower in the ketoglutarate arm compared with the calcium carbonate arm (4.8+/-0.1 mg/dL v 5.2+/-0.1 mg/dL; P = 0.004), whereas the mean plasma phosphate (4.5+/-0.3 mg/dL v 5.1+/-0.1 mg/dL) and PTH levels (266+/-125 pg/mL v 301+/-148 pg/mL) did not differ significantly between the two treatment arms. Supplemental aluminum-aminoacetate was not required during calcium ketoglutarate treatment, while two patients needed this supplement when treated with calcium carbonate. Five of 17 (29%) patients were withdrawn from calcium ketoglutarate therapy within 1 to 2 weeks due to intolerance (anorexia, vomiting, diarrhea, general uneasiness), whereas the remaining 12 patients did not experience any side effects at all. The five patients with calcium ketoglutarate intolerance all had pre-existing gastrointestinal symptoms; four of them had received treatment with cimetidine or omeprazol before inclusion into the study. Calculations based on median doses after 12 weeks showed that the cost of the therapy in Denmark was 10 times higher for calcium ketoglutarate compared with calcium

  14. Electron diffraction and high resolution transmission electron microscopy in the characterization of calcium phosphate precipitation from aqueous solutions under biomineralization conditions

    Directory of Open Access Journals (Sweden)

    Suvorova E. I.

    2001-01-01

    Full Text Available Calcium phosphate precipitation obtained from aqueous solutions at room and body temperature and pH 5.5-7.5 were investigated by high-resolution transmission electron microscopy (HRTEM, transmission electron diffraction, scanning electron microscopy (SEM and X-ray diffraction (XRD. Supersaturated solutions of calcium phosphates were prepared by different methods of mixing of the stock solutions: diffusion-controlled mixing in space, convection-controlled mixing on earth and forced mixing on earth and with typical physiological parameters (pH and temperature. Concentrations of the stock solutions, rate of solution mixing and duration of precipitation influence very strongly the chemical composition of the precipitation, the phase composition of individual crystals, their sizes, morphology and structure. Microdiffraction and HRTEM techniques showed an incontestable advantage on other techniques like SEM and XRD in the investigation of small particles and mixtures of calcium phosphates (hydroxyapatite and octacalcium phosphate with different proportions.

  15. Effect of Reaction Pathway on the Extent and Mechanism of Uranium(VI) Immobilization with Calcium and Phosphate

    Energy Technology Data Exchange (ETDEWEB)

    Mehta, Vrajesh S.; Maillot, Fabien; Wang, Zheming; Catalano, Jeffrey G.; Giammar, Daniel E.

    2016-03-15

    Phosphate addition to subsurface environments contaminated with uranium can be used as an in situ remediation approach. Batch experiments were conducted to evaluate the dependence of the extent and mechanism of uranium uptake on the pathway for reaction with calcium phosphates. At pH 4.0 and 6.0 uranium uptake occurred via autunite (Ca(UO2)(PO4)3) precipitation irrespective of the starting forms of calcium and phosphate. At pH 7.5, the uptake mechanism depended on the nature of the calcium and phosphate. When dissolved uranium, calcium, and phosphate were added simultaneously, uranium was structurally incorporated into a newly formed amorphous calcium phosphate solid. Adsorption was the dominant removal mechanism for uranium contacted with pre-formed amorphous calcium phosphate solids,. When U(VI) was added to a suspension containing amorphous calcium phosphate solids as well as dissolved calcium and phosphate, then removal occurred through precipitation (57±4 %) of autunite and adsorption (43±4 %) onto calcium phosphate. The solid phase speciation of the uranium was determined using X-ray absorption spectroscopy and laser induced fluorescence spectroscopy. Dissolved uranium, calcium, and phosphate concentrations with saturation index calculations helped identify removal mechanisms and determine thermodynamically favorable solid phases.

  16. 钙磷摩尔比对新型PCCP+DCPA体系骨水泥性能的影响%INFLUENCE OF CALCIUM TO PHOSPHATE MOLAR RATIO ON PERFORMANCE OF A NOVEL CALCIUM PHOSPHATE CEMENT

    Institute of Scientific and Technical Information of China (English)

    王秀鹏; 叶建东; 王迎军

    2007-01-01

    Partially crystallized calcium phosphates (PCCP) with different calcium to phosphate molar ratios (n(Ca)/n(P), the same below) and containing carbonate were synthesized by chemical precipitation method. A novel calcium phosphate cement was prepared by PCCP and dicalcium phosphate anhydrous (DCPA). The effects of n(Ca)/n(P) ratio on the properties of the PCCP-DCPA cement system were studied by X-ray diffraction, scanning electron microscope, porosity measurement, and compressive strength analysis.The results show that with the increase of n(Ca)/n(P) ratio, the compressive strength of the cement samples decreased significantly,whereas the crystallinity, porosity and pore fractions larger than 100 nm in the hydrated cement increased. The properties of the cement were greatly influenced by the n(Ca)/n(P) ratio. The n(Ca)/n(P) ratio must be carefully considered in the preparation of calcium phosphate cement.%用化学沉淀法合成了不同钙/磷摩尔比并含碳酸根的部分结晶磷酸钙(partially crystallized calcium phosphates,PCCP),用PCCP和无水磷酸氢钙(dicalcium phosphate anhydrous ,DCPA)配制了PCCP+DCPA体系磷酸钙骨水泥,用去离子水作为骨水泥的固化液.通过相组成的X射线衍射分析、扫描电子显微镜观察、孔隙率和抗压强度测定,研究了钙磷摩尔[n(Ca)/n(P)]对PCCP+DCPA磷酸钙骨水泥性能的影响.结果表明:随着部分结晶磷酸钙中n(Ca)/n(P)的提高,磷酸钙骨水泥试件的抗压强度明显下降,但磷酸钙骨水泥水化产物羟基磷灰石的结晶度提高,固化体中大于100 nm的孔隙增多、固化体的孔隙率增大,可见,n(Ca)/n(P)对磷酸钙骨水泥的性能有重要影响,在制备磷酸钙骨水泥时应选择适当的n(Ca)/n(P).

  17. Calcium phosphate formation from sea urchin - (brissus latecarinatus) via modified mechano-chemical (ultrasonic) conversion method

    OpenAIRE

    R. Samur; Ozyegin, L.; D. Agaogullari; F. N. Oktar; Agathopoulos, S.; Kalkandelen, C.; I. Duman; B. Ben-Nissan

    2013-01-01

    This study aims to produce apatite structures, such as hydroxyapatite (HA) and fluorapatite (FA), from precursor calcium phosphates of biological origin, namely from sea urchin, with mechano-chemical stirring and hot-plating conversion method. The produced materials were heat treated at 800 °C for 4 hours. X-ray diffraction and scanning electron microscopy (SEM) studies were conducted. Calcium phosphate phases were developed. The SEM images showed the formation of micro to nano-powders. The e...

  18. A New Type of Biphasic Calcium Phosphate Cement as a Gentamicin Carrier for Osteomyelitis

    Directory of Open Access Journals (Sweden)

    Wen-Yu Su

    2013-01-01

    Full Text Available Osteomyelitis therapy is a long-term and inconvenient procedure for a patient. Antibiotic-loaded bone cements are both a complementary and alternative treatment option to intravenous antibiotic therapy for the treatment of osteomyelitis. In the current study, the biphasic calcium phosphate cement (CPC, called α-TCP/HAP (α-tricalcium phosphate/hydroxyapatite biphasic cement, was prepared as an antibiotics carrier for osteomyelitis. The developed biphasic cement with a microstructure of α-TCP surrounding the HAP has a fast setting time which will fulfill the clinical demand. The X-ray diffraction and Fourier transform infrared spectrometry analyses showed the final phase to be HAP, the basic bone mineral, after setting for a period of time. Scanning electron microscopy revealed a porous structure with particle sizes of a few micrometers. The addition of gentamicin in α-TCP/HAP would delay the transition of α-TCP but would not change the final-phase HAP. The gentamicin-loaded α-TCP/HAP supplies high doses of the antibiotic during the initial 24 hours when they are soaked in phosphate buffer solution (PBS. Thereafter, a slower drug release is produced, supplying minimum inhibitory concentration until the end of the experiment (30 days. Studies of growth inhibition of Staphylococcus aureus and Pseudomonas aeruginosa in culture indicated that gentamicin released after 30 days from α-TCP/HAP biphasic cement retained antibacterial activity.

  19. Simplified estimates of ion-activity products of calcium oxalate and calcium phosphate in mouse urine.

    Science.gov (United States)

    Tiselius, Hans-Göran; Ferraz, Renato Ribeiro Nogueira; Heilberg, Ita Pfeferman

    2012-08-01

    This study aimed at formulating simplified estimates of ion-activity products of calcium oxalate (AP(CaOx)) and calcium phosphate (AP(CaP)) in mouse urineto find the most important determinants in order to limit the analytical work-up. Literature data on mouse urine composition was used to determine the relative effect of each urine variable on the two ion-activity products. AP(CaOx) and AP(CaP) were calculated by iterative approximation with the EQUIL2 computerized program. The most important determinants for AP(CaOx) were calcium, oxalate and citrate and for AP(CaP) calcium, phosphate, citrate, magnesium and pH. Urine concentrations of the variables were used. A simplified estimate of AP(CaOx) (AP(CaOx)-index(MOUSE)) that numerically approximately corresponded to 10(8) × AP(CaOx) was given the following expression:[Formula: see text]For a series of urine samples with various composition the coefficient of correlation between AP(CaOx)-index(MOUSE) and 10(8) × AP(CaOx) was 0.99 (p = 0.00000). A similar estimate of AP(CaP) (AP(CaP)-index(MOUSE)) was formulated so that it approximately would correspond numerically to 10(14) × AP(CaP) taking the following form:[Formula: see text]For a series of variations in urine composition the coefficient of correlation was 0.95 (p = 0.00000). The two approximate estimates shown in this article are simplified expressions of AP(CaOx) and AP(CaP). The intention of these theoretical calculations was not to get methods for accurate information on the saturation levels in urine, but to have mathematical tools useful for rough conclusions on the outcome of different experimental situations in mice. It needs to be emphasized that the accuracy will be negatively influenced if urine variables not included in the formulas differ very much from basic concentrations.

  20. RBS and XPS analyses of the composite calcium phosphate coatings for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Ide-Ektessabi, Ari [Faculty of Engineering, Graduate School of Engineering, Kyoto University, Kyoto 606-8501 (Japan) and International Innovation Center, Kyoto University, Yoshida Honmachi, Kyoto 606-8501 (Japan)]. E-mail: h51167@sakura.kudpc.kyoto-u.ac.jp; Yamaguchi, Tetsuro [Faculty of Engineering, Graduate School of Engineering, Kyoto University, Kyoto 606-8501 (Japan); Tanaka, Yoshikazu [Faculty of Engineering, Graduate School of Engineering, Kyoto University, Kyoto 606-8501 (Japan)

    2005-12-15

    The calcium phosphate coatings on metallic implants are widely used for biomedical applications. The calcium phosphate coatings require mechanical strength, strong adhesion to the metallic implants, chemical stability and low dissolution into the human body fluid for stable functioning in the corrosive environment of the human body. In this study, a novel approach for improving the calcium phosphate coatings is utilized by adding trace metallic element into the coatings. We focused on teeth enamel, which is the hardest calcium phosphate tissue in the human body. Zn concentration increases exponentially from the interior to the surface of the enamel. As the Zn concentration increases, so the local hardness increases. Our previous studies suggest that Zn has influence on the hardness and other properties of enamel, calcium phosphate tissue. Calcium phosphate coatings doped with Zn was fabricated and characterized. The atomic composition and chemical state were investigated by using Rutherford backscattering spectroscopy (RBS) and X-ray photoelectron spectrometer (XPS), respectively. Scratch test was also carried out for measuring the adhesion of the coatings.

  1. Constant composition dissolution of mixed phases. II. Selective dissolution of calcium phosphates.

    Science.gov (United States)

    Tang, Ruikang; Hass, Michael; Wu, Wenju; Gulde, Stacey; Nancollas, George H

    2003-04-15

    Characterization of the dissolution kinetics of individual synthetic and biological calcium phosphates is of considerable importance since these phases often coexist in biological minerals. The constant composition method has been used to study the dissolution kinetics of a series of synthetic calcium phosphates, brushite (DCPD), beta-tricalcium phosphate (TCP), octacalcium phosphate (OCP), hydroxyapatite (HAP), and carbonated apatite (CAP) in the presence and absence of citric acid, as a function of pH and thermodynamic driving force. While citric acid markedly accelerates the dissolution of TCP, HAP dissolution is significantly inhibited. Moreover, this additive has almost no influence on the dissolution of DCPD, OCP, and CAP. Dual constant composition dissolution studies of mixed calcium phosphates in the presence of citric acid have also been made. Another factor, pH, also plays an important role in the dissolution of these calcium phosphates. In suspensions of calcium phosphate mixtures, specific phases can be selectively dissolved by changing experimental parameters such as pH and the presence of rate modifiers. This result has important applications for the dissolution control of dental hard tissues such as dentin, enamel, and calculus.

  2. Influence of raw powder granulometry on the mechanical properties of a calcium phosphate bone cement

    Energy Technology Data Exchange (ETDEWEB)

    Pittet, C. [Swiss Federal Inst. of Tech., Lausanne (Switzerland). Lab. de Technologie des Poudres; Hopital Orthopedique de la Suisse Romande, Lausanne (Switzerland); Grasso, P.; Lemaitre, J. [Swiss Federal Inst. of Tech., Lausanne (Switzerland). Lab. de Technologie des Poudres

    2002-07-01

    Brushite cement is a calcium phosphate cement obtained by mixing three powders with water. Starting powders are monocalcium phosphate monohydrate (MCPM), calcium sulfate hemihydrate (CSH) and {beta}-tricalcium phosphate ({beta}-TCP). The main phase obtained after setting is brushite (DCPD). The goal of this work was to mill the starting powders to obtain a finer and more homogeneous microstructure after setting, in order to enhance the mechanical properties of the cement. All three powders were milled and freeze-dried. The median diameters passed from 70.5 to 6.2 {mu}m for MCPM, 27.2 to 1.1 {mu}m for CSH, 2.4 to 1.5 {mu}m for {beta}-TCP. Specific surface areas of the powders increased on milling. Attrition of MCPM and CSH appeared to be beneficial to the maximum stresses the set cement can withstand. Cements prepared with raw powders showed 1.4 MPa indirect tensile strength and 4.4 MPa compressive strength. With milled MCPM and CSH, those values reached 4.1 and 22.1 MPa respectively. After these benefits, we tried to use the milled {beta}-TCP expecting further enhancement. To ensure wetting of all three powders and to keep the same paste rheology, the liquid/solid ratio had to be increased. The indirect tensile strength was seen to decrease by a factor of 3 when three milled powders were used at the same time. SEM of the fracture surfaces showed that milled {beta}-TCP formed clusters that did not react to form brushite. Lowering the maximum indirect tension stress is due to the fact that less brushite was formed, and to a higher porosity in the final product (mainly due to the higher liquid/solid ratio). (orig.)

  3. Porous hydroxyapatite and biphasic calcium phosphate ceramics promote ectopic osteoblast differentiation from mesenchymal stem cells

    Science.gov (United States)

    Zhang, Lingli; Hanagata, Nobutaka; Maeda, Megumi; Minowa, Takashi; Ikoma, Toshiyuki; Fan, Hongsong; Zhang, Xingdong

    2009-04-01

    Because calcium phosphate (Ca-P) ceramics have been used as bone substitutes, it is necessary to investigate what effects the ceramics have on osteoblast maturation. We prepared three types of Ca-P ceramics with different Ca-P ratios, i.e. hydroxyapatite (HA), beta-tricalcium phosphate (β-TCP), and biphasic calcium phosphate (BCP) ceramics with dense-smooth and porous structures. Comprehensive gene expression microarray analysis of mouse osteoblast-like cells cultured on these ceramics revealed that porous Ca-P ceramics considerably affected the gene expression profiles, having a higher potential for osteoblast maturation. In the in vivo study that followed, porous Ca-P ceramics were implanted into rat skeletal muscle. Sixteen weeks after the implantation, more alkaline-phosphatase-positive cells were observed in the pores of hydroxyapatite and BCP, and the expression of the osteocalcin gene (an osteoblast-specific marker) in tissue grown in pores was also higher in hydroxyapatite and BCP than in β-TCP. In the pores of any Ca-P ceramics, 16 weeks after the implantation, we detected the expressions of marker genes of the early differentiation stage of chondrocytes and the complete differentiation stage of adipocytes, which originate from mesenchymal stem cells, as well as osteoblasts. These marker gene expressions were not observed in the muscle tissue surrounding the implanted Ca-P ceramics. These observations indicate that porous hydroxyapatite and BCP had a greater potential for promoting the differentiation of mesenchymal stem cells into osteoblasts than β-TCP.

  4. Influence of surface microstructure and chemistry on osteoinduction and osteoclastogenesis by biphasic calcium phosphate discs

    Directory of Open Access Journals (Sweden)

    NL Davison

    2015-06-01

    Full Text Available It has been reported that surface microstructural dimensions can influence the osteoinductivity of calcium phosphates (CaPs, and osteoclasts may play a role in this process. We hypothesised that surface structural dimensions of ≤ 1 μm trigger osteoinduction and osteoclast formation irrespective of macrostructure (e.g., concavities, interconnected macropores, interparticle space or surface chemistry. To test this, planar discs made of biphasic calcium phosphate (BCP: 80 % hydroxyapatite, 20 % tricalcium phosphate were prepared with different surface structural dimensions – either ~ 1 μm (BCP1150 or ~ 2-4 μm (BCP1300 – and no macropores or concavities. A third material was made by sputter coating BCP1150 with titanium (BCP1150Ti, thereby changing its surface chemistry but preserving its surface structure and chemical reactivity. After intramuscular implantation in 5 dogs for 12 weeks, BCP1150 formed ectopic bone in 4 out of 5 samples, BCP1150Ti formed ectopic bone in 3 out of 5 samples, and BCP1300 formed no ectopic bone in any of the 5 samples. In vivo, large multinucleated osteoclast-like cells densely colonised BCP1150, smaller osteoclast-like cells formed on BCP1150Ti, and osteoclast-like cells scarcely formed on BCP1300. In vitro, RAW264.7 cells cultured on the surface of BCP1150 and BCP1150Ti in the presence of osteoclast differentiation factor RANKL (receptor activator for NF-κB ligand proliferated then differentiated into multinucleated osteoclast-like cells with positive tartrate resistant acid phosphatase (TRAP activity. However, cell proliferation, fusion, and TRAP activity were all significantly inhibited on BCP1300. These results indicate that of the material parameters tested – namely, surface microstructure, macrostructure, and surface chemistry – microstructural dimensions are critical in promoting osteoclastogenesis and triggering ectopic bone formation.

  5. Calcium phosphate cement incorporated with N-acetylcysteine-loaded silk fibroin microspheres:preparation and characterization%N-乙酰半胱氨酸丝素微球复合磷酸钙骨水泥的制备及表征

    Institute of Scientific and Technical Information of China (English)

    姜磊; 皮斌; 冯焘; 李斌; 陆英杰; 杨惠林; 朱雪松

    2016-01-01

    BACKGROUND:Calcium phosphate bone cement has been applied to clinical surgery because of its good biocompatibility and osteoconduction. However poor mechanical properties and lack of osteoinductivity limit its wide application. OBJECTIVE:To develop calcium phosphate cement incorporated with N-acetylcysteine (NAC) loaded silk fibroin microspheres (SFM), which is a kind of new injectable bone graft material with slow-release function, and evaluate its physical and chemical properties and cel compatibility. METHODS: Empty SFMs were prepared with emulsion solvent evaporation to absorb NAC solution of different concentrations by NAC-SFM and the concentration of NAC at the maximum drug loading ratio was determined. Then, NAC-SFM was loaded into calcium phosphate bone cement to test the drug release propertiesin vitro. MC3T3-E1 osteoblasts were cultured on the surface of NAC-SFM calcium phosphate bone cement and cel attachment and growth were observed by scanning electron microscope. Additionaly, MC3T3-E1 cels were cultured with three kinds of bone cement extracts (calcium phosphate cement, SFM-calcium phosphate cement, NAC-SFM-calcium phosphate cement, as wel as cultured in theα-minimum essential medium containing a volume fraction of 10% fetal bovine serum and 1% penicilin-streptomycin double antibody as the control. MTS assay was used to evaluate cel proliferation. RESULTS AND CONCLUSION:Microspheres in the composite bone cement presented with smooth surface, same size, diffused distribution and no obvious destroy. Thus, the SFM could remain stable in the reaction process of the composite bone cement. The double slow release system which contained silk fibroin microspheres and calcium phosphate bone cement showed a significant decrease in the cumulative release percentage of NAC within the first 24 hours compared with the control group (P   目的:制备复合N-乙酰半胱氨酸丝素微球的注射性磷酸钙骨水泥,构建一种具有药物缓释功能

  6. Enzymatic pH control for biomimetic deposition of calcium phosphate coatings

    NARCIS (Netherlands)

    Nijhuis, A.W.G.; Nejadnik, M.R.; Nudelman, F.; Walboomers, X.F.; Riet, J. te; Habibovic, P.; Tahmasebi Birgani, Z.; Li, Y.; Bomans, P.H.; Jansen, J.A.; Sommerdijk, N.A.; Leeuwenburgh, S.C.G.

    2014-01-01

    The current study examines the enzymatic decomposition of urea into carbon dioxide and ammonia as a means to increase the pH during biomimetic deposition of calcium phosphate (CaP) onto implant surfaces. The kinetics of the enzymatically induced pH increase were studied by monitoring pH, calcium con

  7. Calcium carbonate-calcium phosphate mixed cement compositions for bone reconstruction.

    Science.gov (United States)

    Combes, C; Bareille, R; Rey, C

    2006-11-01

    The feasibility of making calcium carbonate-calcium phosphate (CaCO(3)-CaP) mixed cements, comprising at least 40% (w/w) CaCO(3) in the dry powder ingredients, has been demonstrated. Several original cement compositions were obtained by mixing metastable crystalline CaCO(3) phases with metastable amorphous or crystalline CaP powders in aqueous medium. The cements set within at most 1 h at 37 degrees C in atmosphere saturated with water. The hardened cement is microporous and exhibits weak compressive strength. The setting reaction appeared to be essentially related to the formation of a highly carbonated nanocrystalline apatite phase by reaction of the metastable CaP phase with part or almost all of the metastable CaCO(3) phase. The recrystallization of metastable CaP varieties led to a final cement consisting of a highly carbonated poorly crystalline apatite analogous to bone mineral associated with various amounts of vaterite and/or aragonite. The presence of controlled amounts of CaCO(3) with a higher solubility than that of the apatite formed in the well-developed CaP cements might be of interest to increase resorption rates in biomedical cement and favors its replacement by bone tissue. Cytotoxicity testing revealed excellent cytocompatibility of CaCO(3)-CaP mixed cement compositions.

  8. Polymerization shrinkage and stress development in amorphous calcium phosphate/urethane dimethacrylate polymeric composites

    Science.gov (United States)

    Antonucci, J.M.; Regnault, W. F.; Skrtic, D.

    2010-01-01

    This study explores how substituting a new high molecular mass oligomeric poly(ethylene glycol) extended urethane dimethacrylate (PEG-U) for 2-hydroxyethyl methacrylate (HEMA) in photo-activated urethane dimethacrylate (UDMA) resins affects degree of vinyl conversion (DC), polymerization shrinkage (PS), stress development (PSSD) and biaxial flexure strength (BFS) of their amorphous calcium phosphate (ACP) composites. The composites were prepared from four types of resins (UDMA, PEG-U, UDMA/HEMA and UDMA/PEG-U) and zirconia-hybridized ACP. Introducing PEG-U improved DC while not adversely affecting PS, PSSD and the BFS of composites. This improvement in DC is attributed to the long, more flexible structure between the vinyl groups of PEG-U and its higher molecular mass compared to poly(HEMA). The results imply that PEG-U has the potential to serve as an alternative to HEMA in dental and other biomedical applications. PMID:20169007

  9. Preparation of hierarchically organized calcium phosphate–organic polymer composites by calcification of hydrogel

    Directory of Open Access Journals (Sweden)

    Kozue Furuichi, Yuya Oaki, Hirofumi Ichimiya, Jun Komotori and Hiroaki Imai

    2006-01-01

    Full Text Available A novel type of calcium phosphate–organic polymer composite having a hierarchical structure was prepared by calcification of a poly(acrylic acid hydrogel. Macroscopically, an organic gel containing phosphate ions was transformed into an opaque solid material by diffusion of calcium ions. We observed the formation of micrometer-scale layered structures consisting of nanoscale crystals of hydroxylapatite (HAp in the opaque products. The laminated architecture resulting from the periodic precipitation of calcium phosphate varied with the reaction conditions, such as the concentrations of the precursor ions and the density of the gel. The nanoscopic structure of HAp crystals was modified by the addition of gelatin to the polymer matrix.

  10. Micronutrients-incorporated calcium phosphate particles with protective effect on osteoporotic bone tissue.

    Science.gov (United States)

    Chen, X; Zhang, L; Yang, X; Li, Z; Sun, X; Lin, M; Yang, G; Gou, Z

    2013-01-01

    Supplementation of individual micronutrient is inadequate for maintaining bone function because single micronutrient can not contribute significantly a positive remodeling balance. We developed the highly integrated, stably dietary multi-micronutrients with good bioavailability and low adverse effect on the improvement of bone consolidation in osteoporosis. The trace element-codoped calcium phosphate (teCaP) particles were prepared in the modified body fluid and carefully evaluated. Rats, aged 3 months, were ovariectomized and when 6 month intervened with the conditioned, low, moderate, and high teCaP diets. The teCaP particles showed highly dissolvable in stomach juice-mimicing acidic solutions. Three months after intervention, the body weight increase showed remarkable differences among the low teCaP diet (~52 g), moderate teCaP diet (~34 g) and high teCaP diet (~23 g) group. In particular, the intake of moderate teCaP greatly improved the retention of trace elements in femural bone for better protection against the skeletal weakening, and resulted in a significant increase of bone mineral density (104.06%) in comparison with the conventional high calcium plus vitamin D3 diet (Control group). These investigations improve our understanding of micronutrient retention on bone consolidation in osteoporotic bone tissue, and also provide new mild wet-chemical approach to prepare potent nutritionally effective edible complements to synergistically relieve bone degeneration and prevent osteoporosis.

  11. Shear-mediated crystallization from amorphous calcium phosphate to bone apatite.

    Science.gov (United States)

    Niu, Xufeng; Wang, Liyang; Tian, Feng; Wang, Lizhen; Li, Ping; Feng, Qingling; Fan, Yubo

    2016-02-01

    The contribution of fluid shear stress (FSS) on the conversion of amorphous calcium phosphate (ACP) to bone apatite is investigated. The ACP precursors are prepared by using a wet-chemistry method and further exposed to the constant FSS environment with values of 0.5, 1.0, 1.5, and 2.0Pa. At the designated time points, the apatites are characterized by transmission electron microscopy, X-ray diffraction, and inductively coupled plasma-mass spectroscopy. The results show that, the low FSS (≤1.0Pa) has positive effects on the transition of ACP, characterized by the accelerated crystallization velocity and the well-organized calcium-deficient hydroxyapatite (CDHA) structure, whereas the high FSS (>1.0Pa) has negative effects on this conversion process, characterized by the poor CDHA crystal morphologies and the destroyed structures. The bioactivity evaluations further reveal that, compared with the FSS-free group, the CDHA prepared under 1.0Pa FSS for 9h presents the more biocompatible features with pre-osteoblast cells. These results are helpful for understanding the mechanism of apatite deposition in natural bone tissue.

  12. Synthesis, characterization and antimicrobial activity of the micro/nano structured biogenic silver doped calcium phosphate

    Science.gov (United States)

    Supraja, N.; Prasad, T. N. V. K. V.; David, Ernest

    2016-01-01

    Scale formation in PVC pipelines reduces the water flow efficiency and enhances microbial contamination. A bio-based composite material comprising of silver doped calcium phosphate (Cp-Ag) was synthesized using a simple technique (photo catalysis) and herein, we report for the first time on preparation and evaluation of the antimicrobial efficacy of silver doped calcite extracted from the scale in drinking water pipe lines. Five concentrations of silver doped calcite materials viz,5, 10, 15, 20 and 25 ppm were prepared using chemical ammonia mediated synthetic method. The material Cp-Ag was characterized by using the techniques UV-Visible spectroscopy, X-ray diffraction, Fourier transform infrared spectroscopy, Scanning electron microscopy, Raman spectroscopy, Thermo gravimetric analysis, X-ray photo electron spectroscopy (XPS), Nuclear magnetic resonance spectrometer and X-ray flouresence microscopy (XRF). Typical rhombohedral structure of the silver doped calcite was observed. XRF and XPS studies confirmed the presence of both calcium and silver in the composite material (Cp-Ag). The silver doped calcite material exhibited enhanced inhibition against Escherichia coli and staphylococcus aureus (Kirby-Bauer discs diffusion assay) which is also dependent on the concentration of the Cp-Ag material.

  13. Structural, morphological and surface characteristics of two types of octacalcium phosphate-derived fluoride-containing apatitic calcium phosphates.

    Science.gov (United States)

    Shiwaku, Y; Anada, T; Yamazaki, H; Honda, Y; Morimoto, S; Sasaki, K; Suzuki, O

    2012-12-01

    Octacalcium phosphate (OCP) has been reported to stimulate bone regeneration during hydrolysis into hydroxyapatite (HA). The present study was designed to characterize structural, morphological and surface properties of fluoride-containing apatitic calcium phosphates (CaP) obtained through OCP hydrolysis or direct precipitation of OCP in the presence of 12-230ppm of fluoride (F). The products were characterized by chemical analysis, X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED) and Fourier transform infrared spectroscopy (FTIR) as well as measurements of surface area, solubility, osteoblastic activities and bovine serum albumin (BSA) adsorption. XRD analysis re-confirmed that both preparations yielded more apatitic CaP with a higher concentration of F. However, the co-precipitated products (CF-CaP) maintained the properties of OCP, in particular the solubility, whereas the hydrolysis products (HF-CaP) had the characteristics of fluoridated apatite. The crystals of plate-like OCP were changed to the crystals of rod-like CF-CaP and small irregular HF-CaP with the advance of the hydrolysis. The SAED analysis detected both OCP and apatite crystals even in the most hydrolyzed CF-CaP. Mouse bone marrow stromal ST-2 cells grew better on CF-CaP compared with HF-CaP. BSA adsorption was inhibited on HF-CaP more than on CF-CaP. These results show that OCP produces physicochemically distinct apatitic fluoridated CaP during hydrolysis, regarding the structure, the crystal morphology and the protein adsorption, depending on the fluoride introduction route, which provides biologically interesting material. Copyright © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  14. Discrimination between biologically relevant calcium phosphate phases by surface-analytical techniques

    Energy Technology Data Exchange (ETDEWEB)

    Kleine-Boymann, Matthias, E-mail: matthias.kleine-boymann@phys.chemie.uni-giessen.de; Rohnke, Marcus, E-mail: marcus.rohnke@phys.chemie.uni-giessen.de; Henss, Anja, E-mail: anja.henss@phys.chemie.uni-giessen.de; Peppler, Klaus, E-mail: klaus.peppler@phys.chemie.uni-giessen.de; Sann, Joachim, E-mail: joachim.sann@phys.chemie.uni-giessen.de; Janek, Juergen, E-mail: juergen.janek@phys.chemie.uni-giessen.de

    2014-08-01

    The spatially resolved phase identification of biologically relevant calcium phosphate phases (CPPs) in bone tissue is essential for the elucidation of bone remodeling mechanisms and for the diagnosis of bone diseases. Analytical methods with high spatial resolution for the discrimination between chemically quite close phases are rare. Therefore the applicability of state-of-the-art ToF-SIMS, XPS and EDX as chemically specific techniques was investigated. The eight CPPs hydroxyapatite (HAP), β-tricalcium phosphate (β-TCP), α-tricalcium phosphate (α-TCP), octacalcium phosphate (OCP), dicalcium phosphate dihydrate (DCPD), dicalcium phosphate (DCP), monocalcium phosphate (MCP) and amorphous calcium phosphate (ACP) were either commercial materials in high purity or synthesized by ourselves. The phase purity was proven by XRD analysis. All of the eight CPPs show different mass spectra and the phases can be discriminated by applying the principal component analysis method to the mass spectrometric data. The Ca/P ratios of all phosphates were determined by XPS and EDX. With both methods some CPPs can be distinguished, but the obtained Ca/P ratios deviate systematically from their theoretical values. It is necessary in any case to determine a calibration curve, respectively the ZAF values, from appropriate standards. In XPS also the O(1s)-satellite signals are correlated to the CPPs composition. Angle resolved and long-term XPS measurements of HAP clearly prove that there is no phosphate excess at the surface. Decomposition due to X-ray irradiation has not been observed.

  15. Sustained delivery of calcium and orthophosphate ions from amorphous calcium phosphate and poly(L-lactic acid)-based electrospinning nanofibrous scaffold

    Science.gov (United States)

    Niu, Xufeng; Liu, Zhongning; Tian, Feng; Chen, Siqian; Lei, Lei; Jiang, Ting; Feng, Qingling; Fan, Yubo

    2017-01-01

    The purpose of this study is to investigate electrospinning poly(L-lactic acid) (PLLA) nanofibrous scaffold with different contents of amorphous calcium phosphate (ACP), which is suitable for using in bone regeneration through sustained release of calcium and orthophosphate ions. Three groups of nanofibrous scaffolds, ACP-free PLLA, ACP-5 wt%/PLLA and ACP-10 wt%/PLLA, are developed and characterized by scanning electron microscopy and gel permeation chromatography. Calcium and phosphate colorimetric assay kits are used to test ions released from scaffold during hydrolytic degradation. The results show ACP-5 wt%/PLLA and ACP-10 wt%/PLLA scaffolds have relatively high degradation rates than ACP-free PLLA group. The bioactivity evaluation further reveals that ACP-5 wt%/PLLA scaffold presents more biocompatible feature with pre-osteoblast cells and significant osteogenesis ability of calvarial bone defect. Due to the facile preparation method, sustained calcium and orthophosphate release behavior, and excellent osteogenesis capacity, the presented ACP/PLLA nanofibrous scaffold has potential applications in bone tissue engineering. PMID:28361908

  16. Controlled adsorption and release onto calcium phosphates materials and drug delivery applications

    Directory of Open Access Journals (Sweden)

    Barroug A.

    2013-11-01

    Full Text Available The adsorptive properties of synthetic calcium phosphates analogous to bone mineral were examined with respect to cisplatin and risedronate, two biological active drugs; the uptake and release experiments were carried out under various conditions in order to understand the basic mechanism of interaction. The effect of temperature and solution composition were highlighted and discussed. The adsorption results obtained for the therapeutic agents demonstrated that, depending on the conditions investigated (nature of the sorbent, concentration range, ionic composition, temperature…, the shape of the isotherms is of Freundlich or Langmuir type. The adsorption is described as an ion-exchange process in dilute solutions, while the interaction appears to be reactive for concentrated solutions (dissolution of mineral ions from the apatite substrate and formation of soluble calcium complex and/or precipitation of calcium salts involving sorbate molecules. The information gained on the surface reactivity of calcium phosphate were exploited to associate an antibiotic to calcium phosphate cements for drug delivery applications. The specimens were obtained by combination of calcium phosphate and calcium carbonate powders upon mixing with water. The physicochemical properties of the paste were altered by the drug loading method (in the liquid or solid phase. Thus, a dose-dependent effect was noticed for the paste setting time, hardening and the release process.

  17. Mg-doped biphasic calcium phosphate by a solid state reaction route: Characterization and evaluation of cytotoxicity

    Energy Technology Data Exchange (ETDEWEB)

    Webler, Geovana D. [Instituto de Física, Universidade Federal de Alagoas, Maceió-AL 57072970 (Brazil); Correia, Ana C.C.; Barreto, Emiliano [Laboratório de Biologia Celular, Universidade Federal de Alagoas, Maceió-AL 57072970 (Brazil); Fonseca, Eduardo J.S., E-mail: eduardo@fis.ufal.br [Instituto de Física, Universidade Federal de Alagoas, Maceió-AL 57072970 (Brazil)

    2015-07-15

    Hydroxyapatite (HAP) and β-tricalcium phosphate (β-TCP) are widely used in tissue engineering because of their chemical similarity to the inorganic bone phase. In this work, we prepare biphasic calcium phosphate (BCP, a mixture of HAP and β-TCP) doped with different concentrations of magnesium to investigate the influence of magnesium on the BCP crystal structure. Magnesium is known to be an important element in the composition of bones and teeth. Recent research has shown that the doping of magnesium into BCP improves its bone metabolism and mechanical properties without affecting its biocompatibility. The samples were prepared by solid-state reaction from calcium carbonate, monobasic ammonium phosphate, and magnesium nitrate hexahydrate. Varying concentrations of magnesium were used and its modifications were examined by different characterization techniques. The phase composition and morphology of the ceramic powders were characterized by X-ray diffraction and scanning electron microscopy, respectively. The functional groups were analyzed using Fourier transform infrared spectroscopy and Raman spectroscopy. Cell viability experiments, using macrophage-like cell lines J774, showed that the synthesized Mg-doped BCP did not exhibit cytotoxicity regardless of the doses assayed or the different concentrations of magnesium used, suggesting it as a good material for potential biological applications. - Highlights: • Simple and fast method for the preparation of the Mg-BCP. • Study of the influence of the incorporation of Mg in the BCP. • Cell viability showed that the synthesized Mg-BCP did not exhibit cytotoxicity.

  18. Preparation and biological efficacy of haddock bone calcium tablets

    Institute of Scientific and Technical Information of China (English)

    霍健聪; 邓尚贵; 谢超; 童国忠

    2010-01-01

    To investigate the possible use of waste products obtained after processing haddock, the present study prepared haddock bone calcium powder by NaOH and ethanol soaking (alkalinealcohol method) and prepared haddock bone calcium tablets using the powder in combination with appropriate excipients. The biological efficacy of the haddock bone calcium tablets was investigated using Wistar rats as an experiment model. Results show that the optimal parameters for the alkalinealcohol method are: NaOH concentration 1...

  19. Sensitivity and specificity of 24-hour urine chemistry levels for detecting elevated calcium oxalate and calcium phosphate supersaturation

    Science.gov (United States)

    Rossi, M. Adrian; Singer, Eric A; Golijanin, Dragan J; Monk, Rebeca D; Erturk, Erdal; Bushinsky, David A

    2008-01-01

    Objectives The gold standard for determining likelihood of calcium oxalate (CaOx) and calcium phosphate (CaPhos) stone formation in urine is supersaturation of CaOx and CaPhos. Our objective was to investigate whether traditional measurement of total calcium, oxalate and phosphate in a 24-hour urine collection is sufficiently sensitive and specific for detecting elevated supersaturation to preclude the more expensive supersaturation test. Methods We performed a retrospective review of 150 consecutive patients with nephrolithiasis who underwent measurement of CaOx supersaturation (CaOxSS) and CaPhos supersaturation (CaPhosSS), as well as total calcium, oxalate and phosphate in a 24-hour urine collection. We used various cut-off values to determine sensitivity and specificity of 24-hour urine measurements for detecting elevated CaOxSS and CaPhosSS. Results In men and women, the sensitivity of 24-hour calcium for detecting elevated CaOxSS was 71% and 79%, respectively; for oxalate, sensitivity was 59% and 36%, respectively. In men and women, the sensitivity of 24-hour calcium for detecting elevated CaPhosSS was 74% and 88%, respectively; for phosphate, sensitivity was 57% and 8%, respectively. In men and women, the specificity of 24-hour calcium for detecting elevated CaOxSS was 55% and 48%, respectively; it was 60% for detecting elevated CaPhosSS in both men and women. Conclusion Traditional 24-hour urine analysis is sensitive, but not specific, for detecting elevated CaOxSS and CaPhosSS. Most patients with abnormal 24-hour urine analysis have normal supersaturation, and treatment decisions based on traditional urine analysis would lead to overtreatment in these patients. PMID:18542745

  20. Pathogenic role of basic calcium phosphate crystals in destructive arthropathies.

    Directory of Open Access Journals (Sweden)

    Hang-Korng Ea

    Full Text Available basic calcium phosphate (BCP crystals are commonly found in osteoarthritis (OA and are associated with cartilage destruction. BCP crystals induce in vitro catabolic responses with the production of metalloproteases and inflammatory cytokines such as interleukin-1 (IL-1. In vivo, IL-1 production induced by BCP crystals is both dependant and independent of NLRP3 inflammasome. We aimed to clarify 1/ the role of BCP crystals in cartilage destruction and 2/ the role of IL-1 and NLRP3 inflammasome in cartilage degradation related to BCP crystals.synovial membranes isolated from OA knees were analysed by alizarin Red and FTIR. Pyrogen free BCP crystals were injected into right knees of WT, NLRP3 -/-, ASC -/-, IL-1α -/- and IL-1β-/- mice and PBS was injected into left knees. To assess the role of IL-1, WT mice were treated by intra-peritoneal injections of anakinra, the IL-1Ra recombinant protein, or PBS. Articular destruction was studied at d4, d17 and d30 assessing synovial inflammation, proteoglycan loss and chondrocyte apoptosis. BCP crystals were frequently found in OA synovial membranes including low grade OA. BCP crystals injected into murine knee joints provoked synovial inflammation characterized by synovial macrophage infiltration that persisted at day 30, cartilage degradation as evidenced by loss of proteoglycan staining by Safranin-O and concomitant expression of VDIPEN epitopes, and increased chondrocyte apoptosis. BCP crystal-induced synovitis was totally independent of IL-1α and IL-1β signalling and no alterations of inflammation were observed in mice deficient for components of the NLRP3-inflammasome, IL-1α or IL-1β. Similarly, treatment with anakinra did not prevent BCP crystal effects. In vitro, BCP crystals elicited enhanced transcription of matrix degrading and pro-inflammatory genes in macrophages.intra-articular BCP crystals can elicit synovial inflammation and cartilage degradation suggesting that BCP crystals have a direct

  1. Pathogenic Role of Basic Calcium Phosphate Crystals in Destructive Arthropathies

    Science.gov (United States)

    Ea, Hang-Korng; Chobaz, Véronique; Nguyen, Christelle; Nasi, Sonia; van Lent, Peter; Daudon, Michel; Dessombz, Arnaud; Bazin, Dominique; McCarthy, Geraldine; Jolles-Haeberli, Brigitte; Ives, Annette; Van Linthoudt, Daniel; So, Alexander; Lioté, Frédéric; Busso, Nathalie

    2013-01-01

    Background basic calcium phosphate (BCP) crystals are commonly found in osteoarthritis (OA) and are associated with cartilage destruction. BCP crystals induce in vitro catabolic responses with the production of metalloproteases and inflammatory cytokines such as interleukin-1 (IL-1). In vivo, IL-1 production induced by BCP crystals is both dependant and independent of NLRP3 inflammasome. We aimed to clarify 1/ the role of BCP crystals in cartilage destruction and 2/ the role of IL-1 and NLRP3 inflammasome in cartilage degradation related to BCP crystals. Methodology/ Principal Findings synovial membranes isolated from OA knees were analysed by alizarin Red and FTIR. Pyrogen free BCP crystals were injected into right knees of WT, NLRP3 -/-, ASC -/-, IL-1α -/- and IL-1β-/- mice and PBS was injected into left knees. To assess the role of IL-1, WT mice were treated by intra-peritoneal injections of anakinra, the IL-1Ra recombinant protein, or PBS. Articular destruction was studied at d4, d17 and d30 assessing synovial inflammation, proteoglycan loss and chondrocyte apoptosis. BCP crystals were frequently found in OA synovial membranes including low grade OA. BCP crystals injected into murine knee joints provoked synovial inflammation characterized by synovial macrophage infiltration that persisted at day 30, cartilage degradation as evidenced by loss of proteoglycan staining by Safranin-O and concomitant expression of VDIPEN epitopes, and increased chondrocyte apoptosis. BCP crystal-induced synovitis was totally independent of IL-1α and IL-1β signalling and no alterations of inflammation were observed in mice deficient for components of the NLRP3-inflammasome, IL-1α or IL-1β. Similarly, treatment with anakinra did not prevent BCP crystal effects. In vitro, BCP crystals elicited enhanced transcription of matrix degrading and pro-inflammatory genes in macrophages. Conclusions/ Significance intra-articular BCP crystals can elicit synovial inflammation and cartilage

  2. Osteogenic activity of cyclodextrin-encapsulated doxycycline in a calcium phosphate PCL and PLGA composite

    Energy Technology Data Exchange (ETDEWEB)

    Trajano, V.C.C.; Costa, K.J.R. [Restorative Dentistry Department, Faculty of Dentistry, Universidade Federal de Minas Gerais, Av. Antônio Carlos, 6627, CEP: 31270-901 Belo Horizonte, Minas Gerais (Brazil); Lanza, C.R.M. [Department of Oral Clinical, Surgery and Pathology, Faculty of Dentistry, Universidade Federal de Minas Gerais, Av. Antônio Carlos, 6627, CEP: 31270-901 Belo Horizonte, Minas Gerais (Brazil); Sinisterra, R.D. [Chemistry Department, ICEX, Universidade Federal de Minas Gerais, Av. Antônio Carlos, 6627, CEP: 31270-901 Belo Horizonte, Minas Gerais (Brazil); Cortés, M.E., E-mail: mecortes@ufmg.br [Restorative Dentistry Department, Faculty of Dentistry, Universidade Federal de Minas Gerais, Av. Antônio Carlos, 6627, CEP: 31270-901 Belo Horizonte, Minas Gerais (Brazil)

    2016-07-01

    Composites of biodegradable polymers and calcium phosphate are bioactive and flexible, and have been proposed for use in tissue engineering and bone regeneration. When associated with the broad-spectrum antibiotic doxycycline (DOX), they could favor antimicrobial action and enhance the action of osteogenic composites. Composites of polycaprolactone (PCL), poly(lactic-co-glycolic acid) (PLGA), and a bioceramic of biphasic calcium phosphate Osteosynt® (BCP) were loaded with DOX encapsulated in β-cyclodextrin (βCD) and were evaluated for effects on osteoblastic cell cultures. The DOX/βCD composite was prepared with a double mixing method. Osteoblast viability was assessed with methyl tetrazolium (MTT) assays after 1 day, 7 day, and 14 days of composite exposure; alkaline phosphatase (AP) activity and collagen production were evaluated after 7 days and 14 days, and mineral nodule formation after 14 days. Composite structures were evaluated by scanning electron microscopy (SEM). Osteoblasts exposed to the composite containing 25 μg/mL DOX/βCD had increased cell proliferation (p < 0.05) compared to control osteoblast cultures at all experimental time points, reaching a maximum in the second week. AP activity and collagen secretion levels were also elevated in osteoblasts exposed to the DOX/βCD composite (p < 0.05 vs. controls) and reached a maximum after 14 days. These results were corroborated by Von Kossa test results, which showed strong formation of mineralization nodules during the same time period. SEM of the composite material revealed a surface topography with pore sizes suitable for growing osteoblasts. Together, these results suggest that osteoblasts are viable, proliferative, and osteogenic in the presence of a DOX/βCD-containing BCP ceramic composite. - Highlights: • Doxycycline encapsulated in β-cyclodextrin was incorpored into a polycaprolactone - poly(lactic-co-glycolic acid) - calcium phosphate • Composite’s scaffold carrying doxycycline

  3. Biomimetic synthesis of poly(propylene-fumarate)-calcium phosphate composites for tissue engineering

    Science.gov (United States)

    Hakimi Mehr, Dorna

    A novel in-situ co-precipitation process for the synthesis of poly(propylene-fumarate)-calcium phosphate composites was developed. In this process the calcium phosphate phase nucleates and grows in the presence of poly(propylene-fumarate) (PPF), in a novel two-solvent system including tetrahydrofuran (THF) and water. It was found that the presence of the organic solvent (THF) does not affect the phase evolution of the calcium phosphate. Both in the presence and absence of THF crystalline dicalcium phosphate dihydrate (DCPD, brushite) and poorly crystalline hydroxyapatite (HAp) form, and transform to crystalline HAp after 24 hours of synthesis time. Contrary to the organic solvent, PPF has a significant influence on the calcium phosphate phase that forms in its presence. It is found that PPF provides a template for the formation of the calcium phosphate phase through a coordination bond between the calcium ion and the carbonyl group of the polymer. As a result of this templating, hydroxyapatite can form in a significantly shorter period of time (˜1 hr) compared to the system where PPF is not present (24 hrs). The nature of the calcium phosphate phase that forms in the presence of PPF depends on the molecular weight and concentration of PPF. High concentration of PPF in the composite (e.g. 80%) stabilizes an amorphous calcium phosphate (ACP) phase and hinders its transformation to crystalline apatite, while low concentration of PPF (e.g. 5%) promotes the formation of crystalline apatite. Higher molecular weight PPF (Mw = 4500) is found to be more efficient in stabilizing the amorphous phase compared to lower molecular weight PPF (Mw = 1800). While high molecular weight PPF stabilizes ACP, low molecular weight PPF promotes its conversion to crystalline apatite. TEM observations revealed that flake-like hydroxyapatite crystals form in the absence of PPF while spherical ACP particles form in a composite containing 80% PPF. The ACP nano-particles (50-100 nm in diameter

  4. Comparison of Calcium Phosphate and Zinc Oxide Nanoparticles as Dermal Penetration Enhancers for Albumin.

    Science.gov (United States)

    Shokri, Narges; Javar, H A

    2015-01-01

    Dermal drug delivery is highly preferred by patients due to its several advantages. Protein therapeutics have attracted huge attention recently. Since dermal delivery of proteins encounter problems, in this investigation, zinc oxide nanoparticles and calcium phosphate nanoparticles were compared as enhancers for dermal permeation of albumin. Albumin was applied simultaneously with zinc oxide nanoparticles or calcium phosphate nanoparticles on pieces of mouse skin. Skin permeation of albumin over time was determined using a diffusion cell. Skin distribution of the nanoparticles and albumin over time was determined by optical and fluorescence microscopy. Zinc oxide nanoparticles and calcium phosphate nanoparticles acted as enhancers for skin permeation of albumin. Cumulative permeated albumin in presence of zinc oxide nanoparticles after 0, 0.5, 1, 1.5 and 2 h, were 0±0, 11.7±3.3, 21.1±3.5, 40.2±3.6 and 40.2±3.6 mg, respectively and in presence of calcium phosphate nanoparticles were 0±0, 20.9±7.4, 33.8±5.5, 33.8±3.7 and 33.8±3.7 mg, respectively. After 0.5 h, little amount of albumin was permeated in presence of every kind of the nanoparticles. After 0.5 or 1 h, the permeated albumin in presence of calcium phosphate nanoparticles was more than that in presence of zinc oxide nanoparticles and after 1.5 h the permeated albumin in presence of zinc oxide nanoparticles was more than that in presence of calcium phosphate nanoparticles. Images of skin distribution of the two nanoparticles over time, were somewhat different and distribution of albumin correlated with the distribution of the nanoparticles alone. The profiles of albumin permeation (in presence of each of the nanoparticles) versus time was delayed and linear for both nanoparticles while the slope for calcium phosphate nanoparticles was higher than zinc oxide nanoparticles. The enhancer effect of zinc oxide nanoparticles was stronger while the enhancer effect of calcium phosphate nanoparticles was

  5. Fibronectin-calcium phosphate composite layer on hydroxyapatite to enhance adhesion, cell spread and osteogenic differentiation of human mesenchymal stem cells in vitro

    Energy Technology Data Exchange (ETDEWEB)

    Sogo, Yu [National Institute of Advanced Industrial Science and Technology (AIST), Institute for Human Science and Biomedical Engineering, Central 6, 1-1-1, Higashi, Tsukuba, Ibaraki 305-8566 (Japan); Ito, Atsuo [National Institute of Advanced Industrial Science and Technology (AIST), Institute for Human Science and Biomedical Engineering, Central 6, 1-1-1, Higashi, Tsukuba, Ibaraki 305-8566 (Japan); Matsuno, Tomonori [Department of Oral and Maxillofacial Surgery, School of Life Dentistry at Tokyo, Nippon Dental University, 1-9-20 Fujimi, Chiyoda-ku, Tokyo 102-8159 (Japan); Oyane, Ayako [National Institute of Advanced Industrial Science and Technology (AIST), Nanotechnology Research Institute, Central 4, 1-1-1 Higashi, Tsukuba, Ibaraki 305-8562 (Japan); Tamazawa, Gaku [Department of Oral and Maxillofacial Surgery, School of Life Dentistry at Tokyo, Nippon Dental University, 1-9-20 Fujimi, Chiyoda-ku, Tokyo 102-8159 (Japan); Satoh, Tazuko [Department of Oral and Maxillofacial Surgery, School of Life Dentistry at Tokyo, Nippon Dental University, 1-9-20 Fujimi, Chiyoda-ku, Tokyo 102-8159 (Japan); Yamazaki, Atsushi [Department of Resources and Environmental Engineering, School of Science and Engineering, Waseda University, 3-4-1 Okubo, Shinjuku-ku, Tokyo 169-8555 (Japan); Uchimura, Eiji [Department of Resources and Environmental Engineering, School of Science and Engineering, Waseda University, 3-4-1 Okubo, Shinjuku-ku, Tokyo 169-8555 (Japan); Ohno, Tadao [Department of Resources and Environmental Engineering, School of Science and Engineering, Waseda University, 3-4-1 Okubo, Shinjuku-ku, Tokyo 169-8555 (Japan)

    2007-06-01

    Fibronectin (Fn) and type I collagen (Col) were immobilized on a surface of a hydroxyapatite (HAP) ceramic by coprecipitation with calcium phosphate in a supersaturated calcium phosphate solution prepared by mixing clinically approved infusion fluids. These proteins and the calcium phosphate precipitate formed a composite surface layer. As a result, the proteins were immobilized firmly as not to be released completely for 3 d in a physiological salt solution. When human mesenchymal stem cells (hMSCs) were cultured on a HAP ceramic in a differentiation medium supplemented with dexamethasone, {beta}-glycerophosphate and ascorbic acid, hMSCs spread well within 1 h. The alkaline phosphatase (ALP) activity of hMSCs cultured on the Fn-calcium phosphate composite layer significantly increased compared with that of hMSCs cultured on the untreated HAP ceramic. On the other hand, Col did not increase the ALP activity of hMSCs and no synergy between Fn and Col was observed. Therefore, the Fn-calcium phosphate composite layer formed on the HAP is useful for the enhancement of the spreading and osteogenic differentiation of hMSCs in vitro.

  6. Antibody-conjugated soybean oil-filled calcium phosphate nanoshells for targetted delivery of hydrophobic molecules.

    Science.gov (United States)

    Schmidt, H T; Kroczynski, M; Maddox, J; Chen, Y; Josephs, R; Ostafin, A E

    2006-11-01

    Hollow calcium phosphate nanoparticles capable of encapsulating poorly water-soluble molecules were produced by self-assembly. Previously reported were solid calcium phosphate nanoparticles and water-filled calcium phosphate nanocapsules suited for encapsulating mostly hydrophilic, but not hydrophobic compounds. Here, calcium phosphate was deposited around 100 nm diameter, 1,2-dioleoyl-sn-glycero-3-phosphate stabilized soybean oil nanoemulsions using either calcium chloride or NaOH titrations to achieve shell thickness between 20-70 nm. The surface was functionalized with carboxylic acid via the addition of carboxyethylphosphonic acid to attach Molecular Probes AB-594C antibody using sulpho-n-hydroxysuccinimide and 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide hydrochloride with an efficiency of approximately 70%, while retaining near complete antibody function. Hydrophobic pyrene was encapsulated with an efficiency of 95%, at concentrations much higher than its water solubility limit, and exhibited spectral features characteristic of a hydrophobic environment. These materials can be used in the targeted delivery of many useful, yet poorly water-soluble pharmaceutical and nutraceutical compounds.

  7. New developments in polymer-controlled, bioinspired calcium phosphate mineralization from aqueous solution.

    Science.gov (United States)

    Bleek, Katrin; Taubert, Andreas

    2013-05-01

    The polymer-controlled and bioinspired precipitation of inorganic minerals from aqueous solution at near-ambient or physiological conditions avoiding high temperatures or organic solvents is a key research area in materials science. Polymer-controlled mineralization has been studied as a model for biomineralization and for the synthesis of (bioinspired and biocompatible) hybrid materials for a virtually unlimited number of applications. Calcium phosphate mineralization is of particular interest for bone and dental repair. Numerous studies have therefore addressed the mineralization of calcium phosphate using a wide variety of low- and high-molecular-weight additives. In spite of the growing interest and increasing number of experimental and theoretical data, the mechanisms of polymer-controlled calcium phosphate mineralization are not entirely clear to date, although the field has made significant progress in the last years. A set of elegant experiments and calculations has shed light on some details of mineral formation, but it is currently not possible to preprogram a mineralization reaction to yield a desired product for a specific application. The current article therefore summarizes and discusses the influence of (macro)molecular entities such as polymers, peptides, proteins and gels on biomimetic calcium phosphate mineralization from aqueous solution. It focuses on strategies to tune the kinetics, morphologies, final dimensions and crystal phases of calcium phosphate, as well as on mechanistic considerations.

  8. Surface physical chemistry properties in coated bacterial cellulose membranes with calcium phosphate.

    Science.gov (United States)

    de Olyveira, Gabriel Molina; Basmaji, Pierre; Costa, Ligia Maria Manzine; Dos Santos, Márcio Luiz; Dos Santos Riccardi, Carla; Guastaldi, Fernando Pozzi Semeghini; Scarel-Caminaga, Raquel Mantuaneli; de Oliveira Capote, Ticiana Sidorenko; Pizoni, Elisabeth; Guastaldi, Antônio Carlos

    2017-06-01

    Bacterial cellulose has become established as a new biomaterial, and it can be used for medical applications. In addition, it has called attention due to the increasing interest in tissue engineering materials for wound care. In this work, the bacterial cellulose fermentation process was modified by the addition of chondroitin sulfate to the culture medium before the inoculation of the bacteria. The biomimetic process with heterogeneous calcium phosphate precipitation of biological interest was studied for the guided regeneration purposes on bacterial cellulose. FTIR results showed the incorporation of the chondroitin sulfate in the bacterial cellulose, SEM images confirmed the deposition of the calcium phosphate on the bacterial cellulose surface, XPS analysis showed a selective chemical group influences which change calcium phosphate deposition, besides, the calcium phosphate phase with different Ca/P ratios on bacterial cellulose surface influences wettability. XTT results concluded that these materials did not affect significantly in the cell viability, being non-cytotoxic. Thus, it was produced one biomaterial with the surface charge changes for calcium phosphate deposition, besides different wettability which builds new membranes for Guided Tissue Regeneration. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Calcium phosphate coatings on magnesium alloys for biomedical applications: a review.

    Science.gov (United States)

    Shadanbaz, Shaylin; Dias, George J

    2012-01-01

    Magnesium has been suggested as a revolutionary biodegradable metal for use as an orthopaedic material. As a biocompatible and degradable metal, it has several advantages over the permanent metallic materials currently in use, including eliminating the effects of stress shielding, improving biocompatibility concerns in vivo and improving degradation properties, removing the requirement of a second surgery for implant removal. The rapid degradation of magnesium, however, is a double-edged sword as it is necessary to control the corrosion rates of the materials to match the rates of bone healing. In response, calcium phosphate coatings have been suggested as a means to control these corrosion rates. The potential calcium phosphate phases and their coating techniques on substrates are numerous and can provide several different properties for different applications. The reactivity and low melting point of magnesium, however, require specific parameters for calcium phosphate coatings to be successful. Within this review, an overview of the different calcium phosphate phases, their properties and their behaviour in vitro and in vivo has been provided, followed by the current coating techniques used for calcium phosphates that may be or may have been adapted for magnesium substrates. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  10. An ex situ study of the adsorption of calcium phosphate from solution onto TiO2(110) and Al2O3(0001)

    Science.gov (United States)

    Murphy, M.; Walczak, M. S.; Hussain, H.; Acres, M. J.; Muryn, C. A.; Thomas, A. G.; Silikas, N.; Lindsay, R.

    2016-04-01

    Ex situ atomic force microscopy and x-ray photoelectron spectroscopy are employed to characterise the adsorption of calcium phosphate from an aqueous solution of CaCl2.H2O and KH2PO4 onto rutile-TiO2(110) and α-Al2O3(0001). Prior to immersion, the substrates underwent wet chemical preparation to produce well-defined surfaces. Calcium phosphate adsorption is observed on both rutile-TiO2(110) and α-Al2O3(0001), with atomic force microscopy images indicating island-type growth. In contrast to other studies on less well-defined TiO2 and Al2O3 substrates, the induction period for calcium phosphate nucleation appears to be comparable on these two surfaces.

  11. In situ synthesis of silicon-substituted biphasic calcium phosphate and their performance in vitro

    Science.gov (United States)

    Song, Chang-Weon; Kim, Tae-Wan; Kim, Dong-Hyun; Jin, Hyeong-Ho; Hwang, Kyu-Hong; Lee, Jong Kook; Park, Hong-Chae; Yoon, Seog-Young

    2012-01-01

    In situ preparation of silicon (Si) substituted biphasic calcium phosphate (BCP) of hydroxyapatite (HAp)/ β-tricalcium phosphate (β-TCP) were carried out through aqueous co-precipitation method. The concentrations of added silicon were varied with the phosphor in order to obtain constant Ca/(P+Si) ratios of 1.602. X-ray diffraction (XRD) and Fourier transformed infrared (FTIR) spectroscopy were used to characterize the structure of synthesized silicon substituted BCP powders. The characterization revealed that the formation of biphasic mixtures of different HAp/ β-TCP ratios was dependent on the content of silicon. After immersing in Hanks' balanced salt solution (HBSS) for 1 week, 3 wt% silicon substituted BCP powders were degraded and precipitation started to be formed with small granules consisting of number of flake-like crystal onto the surface of synthesized powders. In the case of 1 wt% silicon substituted BCP powders, the degradation behavior was detected after immersion in HBSS for 3 weeks. On the other hand, silicon unsubtituted BCP powders were not degraded even after that duration. On the basis of these results, silicon substituted BCP is able to develop a new apatite phase on the surface in contact with physiological fluids faster than BCP does. This enhanced reactivity resulted in reduction for the stability of the β-TCP structure due to SiO4 tetrahedral distortion and disorder at the hydroxyl site when silicon incorporates into BCP.

  12. Ionic modification of calcium phosphate cement viscosity. Part II: hypodermic injection and strength improvement of brushite cement.

    Science.gov (United States)

    Barralet, J E; Grover, L M; Gbureck, U

    2004-05-01

    Brushite-forming calcium phosphate cements are of great interest as bone replacement materials because they are resorbable in physiological conditions. However, their short setting times, low mechanical strengths and limited injectability limit broad clinical application. In this study, we showed that a significant improvement of these properties of brushite cement could be achieved by the use of sodium citrate or citric acid as setting retardants, such that workable cement pastes with a powder to liquid ratio of up to 5 could be manufactured. The cement used in this study consisted of an equimolar powder mixture of beta-tricalcium phosphate and monocalcium phosphate hydrate The use of 500 mM-1M retardant solutions as liquid phase enabled initial setting times of 8-12 min. Wet compressive strength were found to be in the range between 12-18 MPa after immersion of uncompacted cement samples in serum for 24 h. A further strength improvement to 32 MPa was obtained by compaction of the cement paste during samples preparation. This is significant because high-temperature processes cannot be used to fabricate hydrated calcium phosphate materials. Cement pastes were injectable through a hypodermic needle at a powder to liquid ratio of 3.3 g/ml when a 1M citric acid was used as liquid phase, thus enabling precise controlled delivery to small defects.

  13. Synthesis, characterization and bioactivity of a calcium-phosphate glass-ceramics obtained by the sol-gel processing method.

    Science.gov (United States)

    Jmal, Nouha; Bouaziz, Jamel

    2017-02-01

    In this work, a calcium-phosphate glass-ceramics was successfully obtained by heat treatment of a mixture of 26.52 in wt.% of fluorapatite (Fap) and 73.48 in wt.% of 77S (77 SiO214 CaO9 P2O5 in wt.%) gel. The calcium phosphate-glass-ceramics was prepared by sol-gel process with tetraethyl orthosilicate (TEOS), triethyl phosphate (TEP), calcium nitrate and fluorapatite. The synthesized powders were characterized by some commonly used tools such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), (31)P magic angle spinning nuclear magnetic resonance (MAS-NMR), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and thin-film X-ray diffraction (TF-XRD). The obtained results seemed to confirm the nucleation and growth of hydroxyapatite (Hap) nano-phase in the glass. Moreover, an in-vitro evaluation of the glass-ceramic was performed. In addition, to assess its bioactive capacity, it was soaked in simulated body fluid (SBF) at different time intervals. The SEM, EDS and TF-XRD analyses showed the deposition of hydroxyapatite on the surface of the specimens after three days of immersion in SBF solution. The mechanical properties of the obtained material such as rupture strength, Vickers hardness and elastic modulus were measured. In addition, the friction coefficient of calcium phosphate-glass-ceramics was tested. The values of the composite of rupture strength (24MPa), Vickers hardness (214Hv), Young's modulus (52.3GPa), shear modulus (19GPa) and friction coefficient (0.327) were obtained. This glass-ceramics can have useful applications in dental prostheses. Indeed, this material may have promising applications for implants because of its content of fluorine, the effective protector against dental caries. Copyright © 2016 Elsevier B.V. All rights reserved.

  14. 钢铁中温锌-钙系黑磷化液研制%Preparation of black zinc-calcium phosphating solution at medium temperature for iron and steel

    Institute of Scientific and Technical Information of China (English)

    陈琳; 罗宏; 赵蛟; 仝哓刚

    2009-01-01

    A formulation for black Zn-Ca phosphating at medium temperature was developed to obtain phosphating films with good appearance and properties. The effect of complexing agent, total acidity and treatment time on thickness, morphology and corrosion resistance of phosphating film was studied. The composition of the phosphating film was analyzed by X-ray fluorescence (XRF).The results showed that black phosphating films with excellent protective property can be obtained with sodium citrate as complexing agent at total acidity 50-100 after treatment for 15-20 min.%为了改善锌一钙系黑色磷化膜的外观和性能,配制了锌-钙系中温黑磷化液,研究了配位剂、总酸度、磷化时间对黑磷化膜厚度、金相形貌和耐蚀性的影响,采用X射线荧光光谱法(XRF)分析了磷化膜的成分.结果表明,采用柠檬酸三钠作配位荆,控制总酸度为50~100,磷化时间15~20 min,能够获得防护性能良好的黑色磷化膜.

  15. Characterization of nickel-doped biphasic calcium phosphate/graphene nanoplatelet composites for biomedical application

    Energy Technology Data Exchange (ETDEWEB)

    Baradaran, S., E-mail: saeid_baradaran@yahoo.com [Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia); Moghaddam, E. [Tropical Infectious Diseases Research and Education Centre, Department of Medical Microbiology, Faculty of Medicine, University of Malaya, 50603 Kuala Lumpur (Malaysia); Nasiri-Tabrizi, Bahman, E-mail: bahman_nasiri@hotmail.com [Advanced Materials Research Center, Materials Engineering Department, Najafabad Branch, Islamic Azad University, Isfahan (Iran, Islamic Republic of); Basirun, W.J. [Department of Chemistry, Faculty of Science, University of Malaya, Kuala Lumpur 50603 (Malaysia); Institute of Nanotechnology& Catalysis Research (NanoCat), University Malaya, 50603 Kuala Lumpur (Malaysia); Mehrali, M. [Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia); Department of Biomedical Engineering, Faculty of Engineering, University of Malaya, Kuala Lumpur 50603 (Malaysia); Sookhakian, M. [Department of Physics, Faculty of Science, University of Malaya, Kuala Lumpur 50603 (Malaysia); Hamdi, M. [Center of Advanced Manufacturing and Material Processing, University of Malaya, 50603 Kuala Lumpur (Malaysia); Alias, Y. [Department of Chemistry, Faculty of Science, University of Malaya, Kuala Lumpur 50603 (Malaysia)

    2015-04-01

    The effect of the addition of an ionic dopant to calcium phosphates for biomedical applications requires specific research due to the essential roles played in such processes. In the present study, the mechanical and biological properties of Ni-doped hydroxyapatite (HA) and Ni-doped HA mixed with graphene nanoplatelets (GNPs) were evaluated. Ni (3 wt.% and 6 wt.%)-doped HA was synthesized using a continuous precipitation method and calcined at 900 °C for 1 h. The GNP (0.5–2 wt.%)-reinforced 6% Ni-doped HA (Ni6) composite was prepared using rotary ball milling for 15 h. The sintering process was performed using hot isostatic pressing at processing conditions of 1150 °C and 160 MPa with a 1-h holding time. The results indicated that the phase compositions and structural features of the products were noticeably affected by the Ni and GNPs. The mechanical properties of Ni6 and 1.5Ni6 were increased by 55% and 75% in hardness, 59% and 163% in fracture toughness and 120% and 85% in elastic modulus compared with monolithic HA, respectively. The in-vitro biological behavior was investigated using h-FOB osteoblast cells in 1, 3 and 5 days of culture. Based on the osteoblast results, the cytotoxicity of the products was indeed affected by the Ni doping. In addition, the effect of GNPs on the growth and proliferation of osteoblast cells was investigated in Ni6 composites containing different ratios of GNPs, where 1.5 wt.% was the optimum value. - Highlights: • Ni doped biphasic calcium phosphate/graphene nanoplatelets composite was investigated. • Mechanical and biological properties were evaluated. • Phase compositions and structural features were influenced noticeably by the Ni and GNPs. • The cytotoxicity of the Ni was improved with the addition of GNPs.

  16. Development of macroporous calcium phosphate scaffold processed via microwave rapid drying

    Energy Technology Data Exchange (ETDEWEB)

    Jamuna-Thevi, K., E-mail: jamuna@sirim.my [Advanced Materials Research Centre (AMREC), SIRIM Berhad, Lot 34, Jalan Hi-Tech 2/3, Kulim Hi-Tech Park, 09000 Kulim, Kedah (Malaysia); Zakaria, F.A. [Advanced Materials Research Centre (AMREC), SIRIM Berhad, Lot 34, Jalan Hi-Tech 2/3, Kulim Hi-Tech Park, 09000 Kulim, Kedah (Malaysia); Othman, R. [Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, Seri Ampangan, 14300 Nibong Tebal, Penang (Malaysia); Muhamad, S. [Bioassay Unit, Herbal Medicine Research Centre (HMRC), Institute for Medical Research (IMR), Jalan Pahang, 50588 Kuala Lumpur (Malaysia)

    2009-06-01

    Porous hydroxyapatite (HA) scaffold has great potential in bone tissue engineering applications. A new method to fabricate macroporous calcium phosphate (CP) scaffold via microwave irradiation, followed by conventional sintering to form HA scaffold was developed. Incorporation of trisodium citrate dihydrate and citric acid in the CP mixture gave macroporous scaffolds upon microwave rapid drying. In this work, a mixture of {beta}-tricalcium phosphate ({beta}-TCP), calcium carbonate (CaCO{sub 3}), trisodium citrate dihydrate, citric acid and double distilled de-ionised water (DDI) was exposed to microwave radiation to form a macroporous structure. Based on gross eye examinations, addition of trisodium citrate at 30 and 40 wt.% in the CP mixture ({beta}-TCP and CaCO{sub 3}) without citric acid indicates increasing order of pore volume where the highest porosity yield was observed at 40 wt.% of trisodium citrate addition and the pore size was detected at several millimeters. Therefore, optimization of pore size was performed by adding 3-7 wt.% of citric acid in the CP mixture which was separately mixed with 30 and 40 wt.% of trisodium citrate for comparison purposes. Fabricated scaffolds were calcined at 600 deg. C and washed with DDI water to remove the sodium hydroxycarbonate and sintered at 1250 deg. C to form HA phase as confirmed in the X-ray diffraction (XRD) results. Based on Archimedes method, HA scaffolds prepared from 40 wt.% of trisodium citrate with 3-7 wt.% of citric acid added CP mixture have an open and interconnected porous structure ranging from 51 to 53 vol.% and observation using Scanning electron microscope (SEM) showed the pore size distribution between 100 and 500 {mu}m. The cytotoxicity tests revealed that the porous HA scaffolds have no cytotoxic potential on MG63 osteoblast-like cells which might allow for their use as biomaterials.

  17. Calcium phosphate nanoparticles carrying BMP-7 plasmid DNA induce an osteogenic response in MC3T3-E1 pre-osteoblasts.

    Science.gov (United States)

    Hadjicharalambous, Chrystalleni; Kozlova, Diana; Sokolova, Viktoriya; Epple, Matthias; Chatzinikolaidou, Maria

    2015-12-01

    Functionalized calcium phosphate nanoparticles with osteogenic activity were prepared. Polyethyleneimine-stabilized calcium phosphate nanoparticles were coated with a shell of silica and covalently functionalized by silanization with thiol groups. Between the calcium phosphate surface and the outer silica shell, plasmid DNA which encoded either for bone morphogenetic protein 7 (BMP-7) or for enhanced green fluorescent protein was incorporated as cargo. The plasmid DNA-loaded calcium phosphate nanoparticles were used for the transfection of the pre-osteoblastic MC3T3-E1 cells. The cationic nanoparticles showed high transfection efficiency together with a low cytotoxicity. Their potential to induce an osteogenic response by transfection was demonstrated by measuring the alkaline phosphatase (ALP) activity and calcium deposition with alizarin red staining. The expression of the osteogenic markers Alp, Runx2, ColIa1 and Bsp was investigated by means of real-time quantitative polymerase chain reaction. It was shown that phBMP-7-loaded nanoparticles can provide a means of transient transfection and localized production of BMP-7 in MC3T3-E1 cells, with a subsequent increase of two osteogenic markers, specifically ALP activity and calcium accumulation in the extracellular matrix. Future strategies to stimulate bone regeneration focus into enhancing transfection efficiency and achieving higher levels of BMP-7 produced by the transfected cells.

  18. Molecular mechanism of crystallization impacting calcium phosphate cements

    Energy Technology Data Exchange (ETDEWEB)

    Giocondi, J L; El-Dasher, B S; Nancollas, G H; Orme, C A

    2009-05-31

    theoretical modeling. The question changes from 'What types of molecules will inhibit brushite growth' to 'What type of molecule will interact with the [10-1]{sub Cc} step?' Similarly, to increase resorption rate, it would be most efficacious to target the slow moving [-100] step, perhaps by targeting the hydroxyl group which seem to stabilize this step compared to its otherwise similar mirror, [100]. In short, there are a number of opportunities where molecular scale imaging can provide new information that has the prospect to aid in optimizing calcium phosphate cements.

  19. A comparative study of calcium phosphate formation on bioceramics in vitro and in vivo.

    Science.gov (United States)

    Xin, Renlong; Leng, Yang; Chen, Jiyong; Zhang, Qiyi

    2005-11-01

    Formation of calcium phosphate (Ca-P) on various bioceramic surfaces in simulated body fluid (SBF) and in rabbit muscle sites was investigated. The bioceramics were sintered porous solids, including bioglass, glass-ceramics, hydroxyapatite, alpha-tricalcium phosphate and beta-tricalcium phosphate. The ability of inducing Ca-P formation was compared among the bioceramics. The Ca-P crystal structures were identified using single-crystal diffraction patterns in transmission electron microscopy. The examination results show that ability of inducing Ca-P formation in SBF was similar among bioceramics, but considerably varied among bioceramics in vivo. Sintered beta-tricalcium phosphate exhibited a poor ability of inducing Ca-P formation both in vitro and in vivo. Octacalcium phosphate (OCP) formed on the surfaces of bioglass, A-W, hydroxyapatite and alpha-tricalcium phosphate in vitro and in vivo. Apatite formation in physiological environments cannot be confirmed as a common feature of bioceramics.

  20. Synthesis and characterization of nanostructured powders of hydroxyapatite and β-calcium phosphate

    Energy Technology Data Exchange (ETDEWEB)

    Prants, W.T.; Muller, D.T.; Orzechowski, L.G.; Feit, G.; Delima, S.A.; Camargo, N.H.A.; Gemelli, E., E-mail: w_prants@hotmail.com, E-mail: danielt_muller@yahoo.com.br, E-mail: sarahamindelima@hotmail.com, E-mail: dem2nhac@joinville.udesc.br, E-mail: gemelli@joinville.udesc.br [Universidade do Estado de Santa Catarina (UDESC), Joinville, SC (Brazil). Campus Universitario Prof. Avelino Marcante

    2009-07-01

    Biphasic calcium phosphate (BCP) bioceramics are composed in a general manner from a mixture between hydroxyapatite (HA), and β-calcium phosphate. In the recent years, the BCP bioceramics are pointed out in researches from regeneration and reconstitution in osseous tissue, in reason of their similar mineralogical characteristics of the human bone structure, as great biodegradation, absorption and formation of precocious osseous tissue. The biphasic materials (BCP) are detached for use in medical and dental application, as filling bone cavities, maxillofacial treatment, medicaments discharge for treatment cancerous osteomyelitis and antibiotics discharge related with orthopedic injuries reparation. The aim of this work focused in synthesis and characterization of hydroxyapatite and β-calcium phosphate. The presented results are related with the mineralogical characterization with X-ray diffraction, thermal behavior with Differential Scanning Calorimetry and Dilatometer. The Scanning Electronic Microscopy (SEM) was used to help in the morphological characterization of the nanostructured powders. (author)

  1. Synthesis and characterization of nanocomposite powders of calcium phosphate/titanium oxide for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Delima, S.A.; Camargo, N.H.A.; Souza, J.C.P.; Gemelli, E., E-mail: sarahamindelima@hotmail.com, E-mail: dem2nhac@joinville.udesc.br, E-mail: souzajulio@joinville.udesc.br, E-mail: gemelli@joinville.udesc.br [Universidade do Estado de Santa Catarina (UDESC), Joinville, SC (Brazil). Centro de Ciencias Tecnologicas

    2009-07-01

    The nanostructured bioceramics of calcium phosphate are current themes of research and they are becoming important as bone matrix in regeneration of tissues in orthopedic and dental applications. Nanocomposite powders of calcium phosphate, reinforced with nanometric particles of titanium oxide, silica oxide and alumina oxid ealpha, are being widely studied because they offer new microstructures, nanostructures and interconnected microporosity with high superficial area of micropores that contribute to osteointegration and osteoinduction processes. This study is about the synthesis of nanocomposites powders of calcium phosphate reinforced with 1%, 2%, 3% and 5% in volume of titanium oxide and its characterization through the techniques of X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Differential Thermal Analysis (DTA), Thermogravimetry (TG) and Dilatometry. (author)

  2. Effect of solute concentration on fibroin regulated biomineralization of calcium phosphate

    Energy Technology Data Exchange (ETDEWEB)

    Kong Xiangdong [Biomaterials Laboratory, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Institute of Biochemistry, Zhejiang Sci-Tech University, Hangzhou 310018 (China); Sun Xiaodan [Biomaterials Laboratory, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Cui Fuzhai [Biomaterials Laboratory, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China)]. E-mail: cuifz@mail.tsinghua.edu.cn; Ma Chen [Biomaterials Laboratory, Department of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China)

    2006-05-15

    In this paper we used UV/Visible method to study the effect of solute concentration on fibroin regulated biomineralization of calcium phosphate. During the reaction process, ultraviolet-visible spectrophotometer was used to track the extinction in the reaction solution. It is found that kinetics of the biomineralization can be strongly affected by the presence of fibroin. Fibroin with higher concentration has more positive effect on the biomineralization process. Under the appropriate reaction conditions, wave crest and wave trough appear in the kinetic curves of fibroin biomineralization. The wave crest and wave trough phenomenon is mainly related with the process of phase separation. X-ray Diffraction (XRD) result shows the calcium phosphate before the wave trough is mainly amorphous calcium phosphate, while after the wave trough crystal of hydroxyapatite (HA) and brushite (DCPD) are the mainly ingredients.

  3. Mechanisms of in Vivo Degradation and Resorption of Calcium Phosphate Based Biomaterials

    Directory of Open Access Journals (Sweden)

    Zeeshan Sheikh

    2015-11-01

    Full Text Available Calcium phosphate ceramic materials are extensively used for bone replacement and regeneration in orthopedic, dental, and maxillofacial surgical applications. In order for these biomaterials to work effectively it is imperative that they undergo the process of degradation and resorption in vivo. This allows for the space to be created for the new bone tissue to form and infiltrate within the implanted graft material. Several factors affect the biodegradation and resorption of calcium phosphate materials after implantation. Various cell types are involved in the degradation process by phagocytic mechanisms (monocytes/macrophages, fibroblasts, osteoblasts or via an acidic mechanism to reduce the micro-environmental pH which results in demineralization of the cement matrix and resorption via osteoclasts. These cells exert their degradation effects directly or indirectly through the cytokine growth factor secretion and their sensitivity and response to these biomolecules. This article discusses the mechanisms of calcium phosphate material degradation in vivo.

  4. Calcium Phosphate Bone Cements Including Sugar Surfactants: Part Two—Injectability, Adhesive Properties and Biocompatibility

    Directory of Open Access Journals (Sweden)

    Fabienne Briand-Mesange

    2010-12-01

    Full Text Available Addition of sugar surfactants, sucrose fatty acid esters and alkylpolyglucosides to a calcium phosphate cement, designed for bone reconstruction, is described. Thanks to their adsorption at the surface of the calcium phosphate particles, the sugar surfactants allowed a full injectability and brought a very good workability. Injectability was measured by monitoring force-distance curves. With some of the selected sugar surfactants adhesive properties of the cement pastes were also observed, which were measured by tack tests. Finally, some properties related to biological applications are described, including gentamicine release and osteoblast viability experiments. The whole study demonstrates that addition of these mild surfactants improved several properties of the calcium phosphate cement, without impairing function.

  5. Calcium phosphate formation from sea urchin - (brissus latecarinatus via modified mechano-chemical (ultrasonic conversion method

    Directory of Open Access Journals (Sweden)

    R. Samur

    2013-07-01

    Full Text Available This study aims to produce apatite structures, such as hydroxyapatite (HA and fluorapatite (FA, from precursor calcium phosphates of biological origin, namely from sea urchin, with mechano-chemical stirring and hot-plating conversion method. The produced materials were heat treated at 800 °C for 4 hours. X-ray diffraction and scanning electron microscopy (SEM studies were conducted. Calcium phosphate phases were developed. The SEM images showed the formation of micro to nano-powders. The experimental results suggest that sea urchin, Brissus latecarinatus skeleton could be an alternative source for the production of various mono or biphasic calcium phosphates with simple and economic mechano-chemical (ultrasonic conversion method.

  6. Silver-doped calcium phosphate nanoparticles: synthesis, characterization, and toxic effects toward mammalian and prokaryotic cells.

    Science.gov (United States)

    Peetsch, Alexander; Greulich, Christina; Braun, Dieter; Stroetges, Christian; Rehage, Heinz; Siebers, Bettina; Köller, Manfred; Epple, Matthias

    2013-02-01

    Spherical silver-doped calcium phosphate nanoparticles were synthesized in a co-precipitation route from calcium nitrate/silver nitrate and ammonium phosphate in a continuous process and colloidally stabilized by carboxymethyl cellulose. Nanoparticles with 0.39 wt% silver content and a diameter of about 50-60 nm were obtained. The toxic effects toward mammalian and prokaryotic cells were determined by viability tests and determination of the minimal inhibitory and minimal bactericidal concentrations (MIC and MBC). Three mammalian cells lines, i.e. human mesenchymal stem cells (hMSC) and blood peripheral mononuclear cells (PBMC, monocytes and T-lymphocytes), and two prokaryotic strains, i.e. Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) were used. Silver-doped calcium phosphate nanoparticles and silver acetate showed similar effect toward mammalian and prokaryotic cells with toxic silver concentrations in the range of 1-3 μg mL(-1).

  7. Mechanical properties of calcium phosphate cements obtained by solution combustion synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Volkmer, Tiago M.; Barreiro, Oscar; Souza, Vania Caldas; Santos, Luis Alberto dos, E-mail: tiagovolkmer@gmail.com, E-mail: oscarbafer@hotmail.com, E-mail: vania.souza@ufrgs.br, E-mail: luis.santos@ufrgs.br [Universidade Federal do Rio Grande do Sul (UFRS), Porto Alegre, RS (Brazil). Laboratorio de Biomateriais

    2009-07-01

    Bioceramics based on calcium phosphates, especially hydroxyapatite and tricalcium phosphates (TCP) are the most used biomaterials as bone substitutes. The objective of this work is to evaluate the mechanical properties of α-tricalcium phosphate (α-TCP) synthesized by the solution combustion method. The solution combustion synthesis (SCS) can be considered as faster and simpler as other methods, furthermore it allows the obtainment of high purity α-TCP. In the calcium phosphates (CPC), α-TCP reacts with water forming needle like HA, which restrain the movement of grains, increasing mechanical resistance. In the present paper the influence of particle size on mechanical properties of α-TCP cements were evaluated. The α-TCP powder were characterized by XRD, TEM, BET and laser diffraction to asses particle size while the CPC bodies by SEM, Arquimedes method and compression tests. Increasing the milling time, the particle size decreases, resulting in samples with less porosity and consequently with higher compression resistance. (author)

  8. Ossification Vesicles with Calcium Phosphate in the Eyes of the Insect Copium teucrii (Hemiptera: Tingidae

    Directory of Open Access Journals (Sweden)

    Javier Garcia-Guinea

    2011-01-01

    Full Text Available Arthropod eyes are built of repeating units named ommatidia. Each single ommatidium unit contains a cluster of photoreceptor cells surrounded by support cells and pigment cells. The insect Copium eye ommatidia include additional calcium-phosphate deposits, not described in insects to date, which can be examined today using a combined set of modern microscopy and spectroscopy techniques. Teucrium gnaphalodes L'Her plants, growing in central Spain, develop galls induced by Copium insects. A survey of C. teucrii adult specimens resulted in surprising environmental scanning electron microscopy (ESEM images, showing that their bright red eyes contain a calcium-phosphate mineralization. A complete survey of Copium eye specimens was performed by ESEM using energy-dispersive spectroscopy, backscattered electron detector and cathodoluminescence (CL probes, field emission scanning electron microscopy, micro-Raman spectroscopy, and confocal laser scanning microscopy in order to learn ommatidia features, such as chemical composition, molecular structure, cell membrane, and internal ommatidium eye fluids and calcium-phosphate distribution deposits. The CL panchromatic images distinguish between the calcium-phosphate ommatidium and calcium-phosphate setae, which are more apatite rich. They show Raman bands attributable to bone tissue apatite biomaterials, such as bone, collagen, lipids, and blood, i.e., peptides, amide-S, amide-II, amide-III, and cytochrome P-450scc. The chemical composition of both galls and leaves of T. gnaphalodes was determined by gas chromatography – mass spectrometry (GC-MS of their extracts. The spectrometric and microscopic images reveal that the calcium-phosphate mineralization is formed and constrained to Copium ommatidia, which are both matrix vesicles generating mixtures of apatite collagen and operational compound eyes of the insect.

  9. First-Row Transition Metal Doping in Calcium Phosphate Bioceramics: A Detailed Crystallographic Study

    Directory of Open Access Journals (Sweden)

    Guillaume Renaudin

    2017-01-01

    Full Text Available Doped calcium phosphate bioceramics are promising materials for bone repair surgery because of their chemical resemblance to the mineral constituent of bone. Among these materials, BCP samples composed of hydroxyapatite (Ca10(PO46(OH2 and β-TCP (Ca3(PO42 present a mineral analogy with the nano-multi-substituted hydroxyapatite bio-mineral part of bones. At the same time, doping can be used to tune the biological properties of these ceramics. This paper presents a general overview of the doping mechanisms of BCP samples using cations from the first-row transition metals (from manganese to zinc, with respect to the applied sintering temperature. The results enable the preparation of doped synthetic BCP that can be used to tailor biological properties, in particular by tuning the release amounts upon interaction with biological fluids. Intermediate sintering temperatures stabilize the doping elements in the more soluble β-TCP phase, which favors quick and easy release upon integration in the biological environment, whereas higher sintering temperatures locate the doping elements in the weakly soluble HAp phase, enabling a slow and continuous supply of the bio-inspired properties. An interstitial doping mechanism in the HAp hexagonal channel is observed for the six investigated cations (Mn2+, Fe3+, Co2+, Ni2+, Cu2+ and Zn2+ with specific characteristics involving a shift away from the center of the hexagonal channel (Fe3+, Co2+, cationic oxidation (Mn3+, Co3+, and also cationic reduction (Cu+. The complete crystallochemical study highlights a complex HAp doping mechanism, mainly realized by an interstitial process combined with calcium substitution for the larger cations of the series leading to potentially calcium deficient HAp.

  10. Treatment of post-orthodontic white spot lesions with casein phosphopeptide-stabilised amorphous calcium phosphate

    DEFF Research Database (Denmark)

    Bröchner, Ann; Christensen, Carsten; Kristensen, Bjarne;

    2010-01-01

    This study aims to investigate the effect of topical applications of 10% casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) on white spot lesions (WSL) detected after treatment with fixed orthodontic appliances. Sixty healthy adolescents with >/=1 clinically visible WSL at debonding were...... findings were largely reflected by the clinical scores. No side effects were reported. Topical treatment of white spot lesions after debonding of orthodontic appliances with a casein phosphopeptide-stabilised amorphous calcium phosphate agent resulted in significantly reduced fluorescence and a reduced...

  11. Bioactivity evaluation of commercial calcium phosphate-based bioceramics for bone regeneration

    Energy Technology Data Exchange (ETDEWEB)

    Borrós, S.; Mas, A.

    2016-11-01

    Calcium phosphate-based bioceramics constitute a great promise for bone tissue engineering as they chemically resemble to mammalian bone and teeth. Their use is a viable alternative for bone regeneration as it avoids the use of autografts and allografts, which usually involves immunogenic reactions and patient’s discomfort. This work evolves around the study of the bioactivity potential of different commercially available bone substitutes based in calcium phosphate through the characterization of their ionic exchangeability when immersed in simulated body fluid (SBF). (Author)

  12. The effects of citric acid on the hydration of calcium phosphate cement

    Institute of Scientific and Technical Information of China (English)

    DAI Hong-lian; YAN Yu-hua; WANG You-fa; LI Shi-pu

    2001-01-01

    @@ INTRODUCTION Calcium phosphate cements (CPC) overcome the practical disadvantages of blocks or granulesl can be handled as a paste and sit in situ. Their structure and composition close to that of HAP make them biocompatible materials. 2 The conventional calcium phosphate cement had some problems such as long setting time (30~60 min) and low compressive strength, etc. In our system, an α-TCP/TTCP powder mixture was mixed with water containing citric acid to control the setting time and compressive strength. In this paper, the effects of various concentration citric acid solutions on the properties of the cement are reported.

  13. Magnesium substitution in the structure of orthopedic nanoparticles: A comparison between amorphous magnesium phosphates, calcium magnesium phosphates, and hydroxyapatites.

    Science.gov (United States)

    Nabiyouni, Maryam; Ren, Yufu; Bhaduri, Sarit B

    2015-01-01

    As biocompatible materials, magnesium phosphates have received a lot of attention for orthopedic applications. During the last decade multiple studies have shown advantages for magnesium phosphate such as lack of cytotoxicity, biocompatibility, strong mechanical properties, and high biodegradability. The present study investigates the role of Mg(+2) and Ca(+2) ions in the structure of magnesium phosphate and calcium phosphate nanoparticles. To directly compare the effect of Mg(+2) and Ca(+2) ions on structure of nanoparticles and their biological behavior, three groups of nanoparticles including amorphous magnesium phosphates (AMPs) which release Mg(+2), calcium magnesium phosphates (CMPs) which release Mg(+2) and Ca(+2), and hydroxyapatites (HAs) which release Ca(+2) were studied. SEM, TEM, XRD, and FTIR were used to evaluate the morphology, crystallinity, and chemical properties of the particles. AMP particles were homogeneous nanospheres, whereas CMPs were combinations of heterogeneous nanorods and nanospheres, and HAs which contained heterogeneous nanosphere particles. Cell compatibility was monitored in all groups to determine the cytotoxicity effect of particles on studied MC3T3-E1 preosteoblasts. AMPs showed significantly higher attachment rate than the HAs after 1 day and both AMPs and CMPs showed significantly higher proliferation rate when compared to HAs after 7days. Gene expression level of osteoblastic markers ALP, COL I, OCN, OPN, RUNX2 were monitored and they were normalized to GAPDH housekeeping gene. Beta actin expression level was monitored as the second housekeeping gene to confirm the accuracy of results. In general, AMPs and CMPs showed higher expression level of osteoblastic genes after 7 days which can further confirm the stimulating role of Mg(+2) and Ca(+2) ions in increasing the proliferation rate, differentiation, and mineralization of MC3T3-E1 preosteoblasts.

  14. MULTIPLE SCATTERING IN THE EXAFS OF CALCIUM PHOSPHATES

    OpenAIRE

    1986-01-01

    Analysis of the EXAFS spectra of hydroxyapatite, brushite and monetite, recorded above the calcium K edge, requires the inclusion of multiple scattering by phosphorus atoms at 0.37 nm, from calcium. If multiple scattering is not included, some variable parameters acquire physically unreasonable values. Atomic radii never had to be varied by more than 0.01 nm from their values in the accepted crystal structures.

  15. The development and characterization of a primarily mineral calcium phosphate - poly(epsilon-caprolactone) biocomposite

    Science.gov (United States)

    Dunkley, Ian Robert

    Orthopaedic reconstruction often involves the surgical introduction of structural implants that provide for rigid fixation, skeletal stabilization, and bone integration. The high stresses incurred by these implanted devices have historically limited material choices to metallic and select polymeric formulations. While mechanical requirements are achieved, these non-degradable materials do not participate actively in the remodeling of the skeleton and present the possibility of long-term failure or rejection. This is particularly relevant in cervical fusion, an orthopaedic procedure to treat damaged, degenerative or diseased intervertebral discs. A significant improvement on the available synthetic bone replacement/regeneration options for implants to treat these conditions in the cervical spine may be achieved with the development of primarily mineral biocomposites comprised of a bioactive ceramic matrix reinforced with a biodegradable polymer. Such a biocomposite may be engineered to possess the clinically required mechanical properties of a particular application, while maintaining the ability to be remodeled completely by the body. A biocomposite of Si-doped calcium phosphate (Si-CaP) and poly(epsilon-caprolactone) (PCL) was developed for application as such a synthetic bone material for potential use as a fusion device in the cervical spine. In this thesis, a method by which high mineral content Si-CaP/PCL biocomposites with interpenetrating matrices of mineral and polymer phases may be prepared will be demonstrated, in addition to the effects of the various preparation parameters on the biocomposite density, porosity and mechanical properties. This new technique by which dense, primarily ceramic Si-CaP/PCL biocomposites were prepared, allowed for the incorporation of mineral contents ranging between 45-97vol%. Polymer infiltration, accomplished solely by passive capillary uptake over several days, was found to be capable of fully infiltrating the microporosity

  16. Correlation between calcium and phosphate levels to calculus accumulation on coronary heart disease patients

    Science.gov (United States)

    Cahaya, Cindy; Masulili, Sri Lelyati C.; Lessang, Robert; Radi, Basuni

    2017-02-01

    Coronary Artery Disease (CAD) or Coronary Heart Disease (CHD) is a disease that happened because of blood flow being blocked by atherosclerosis. Atherosclerosis is a process of hardening of the arteries which characterized by thickening and loss of elasticity of the intimal layer of vascular wall, by lipid deposit. Periodontitis is a chronic multifactorial inflammatory disease caused by microorganism and characterized by progressive destruction of the tooth supporting apparatus leading to tooth loss. Many studies use saliva as a valuable source for clinically information, as an asset for early diagnosis, prognostic and reviewer for pascatherapy status. Dental calculus had happened as a consequence of saliva supersaturation by calcium and phosphate. Salivary flow rate and its composition influence the formation of calculus. Increasing salivary calcium levels is characteristic of periodontitis patients. An important hipotesis in Cardiology is chronic infections contribute in atherosclerosis. Objective: To analyse the correlation between calcium and phosphate levels in saliva to calculus accumulation on CHD patients. Result: Correlation analysis between salivary calcium levels with calculus accumulation in patients with CHD and non-CHD showed no significant p value, p=0.59 and p=0.518. Correlation analysis between salivary phosphate levels and calculus accumulation showed no significant p value, p=0.836 for CHD patients and p=0.484 for non-CHD patients. Conclusion: There are no correlation between calcium levels and phosphate levels with calculus accumulation in CHD patients. Further research need to be done.

  17. Effect of rapidly resorbable calcium phosphates and a calcium phosphate bone cement on the expression of bone-related genes and proteins in vitro.

    Science.gov (United States)

    Knabe, C; Berger, G; Gildenhaar, R; Meyer, J; Howlett, C R; Markovic, B; Zreiqat, H

    2004-04-01

    The use of biodegradable bone substitutes is advantageous for alveolar ridge augmentation because it avoids second-site surgery for autograft harvesting. This study examines the effect of novel, rapidly resorbable calcium phosphates and a calcium phosphate bone cement on the expression of bone-related genes and proteins by human bone-derived cells (HBDCs) and compares this behavior to that of tricalciumphosphate (TCP). Test materials were alpha-TCP, two materials with a crystalline phase Ca(2)KNa(PO(4))(2) and with a small amorphous portion containing either magnesium potassium phosphate (material denominated GB14) or silica phosphate (material denominated GB9), and a calcium phosphate bone cement (material denominated Biocement D). HBDCs were grown on the substrata for 3, 7, 14, and 21 days, counted, and probed for various mRNAs and proteins (type I collagen, osteocalcin, osteopontin, osteonectin, alkaline phosphatase, and bone sialoprotein). All substrates supported continuous cellular growth for 21 days. In the presence of GB14 and Biocement D specimens cell proliferation was reduced and cell differentiation increased. At day 21, the greatest number of cells was found on GB9 expressing significantly higher levels of bone-related proteins than cells grown on all other surfaces. Because all novel materials facilitated the expression of the osteoblastic phenotype at least as much as TCP and the polystyrene control, these biomaterials can be regarded as excellent candidate bone substitute materials. GB9 induced the highest proliferation and cellular differentiation after 21 days of incubation, suggesting that this material may possess a higher potency for enhancing osteogenesis than TCP.

  18. Preparation of material to control precision of calcium selective electrodes.

    Science.gov (United States)

    Fyffe, J A; Jenkins, A S; Bolland, C J; Dryburgh, F J; Gardner, M D

    1981-03-01

    A simple procedure is described for the preparation of a stable precision quality control material for use in the measurement of level of ionised calcium in serum at or near the reference range. Repeat analyses on a Nova 2 ionised calcium analyser of serum pools stored at different temperatures over a period of three months showed coefficients of variation less of less than 4%.

  19. Biomimetic calcium phosphate coating of additively manufactured porous CoCr implants

    Energy Technology Data Exchange (ETDEWEB)

    Lindahl, Carl [BIOMATCELL Vinn Excellence Center of Biomaterials and Cell Therapy, Gothenburg (Sweden); Department of Engineering Sciences, Ångstrom Laboratory, Uppsala University, Uppsala (Sweden); Xia, Wei, E-mail: wei.xia@angstrom.uu.se [BIOMATCELL Vinn Excellence Center of Biomaterials and Cell Therapy, Gothenburg (Sweden); Department of Engineering Sciences, Ångstrom Laboratory, Uppsala University, Uppsala (Sweden); Engqvist, Håkan [BIOMATCELL Vinn Excellence Center of Biomaterials and Cell Therapy, Gothenburg (Sweden); Department of Engineering Sciences, Ångstrom Laboratory, Uppsala University, Uppsala (Sweden); Snis, Anders [BIOMATCELL Vinn Excellence Center of Biomaterials and Cell Therapy, Gothenburg (Sweden); Arcam AB, Krokslätts Fabriker 27 A, SE-431 37 Mölndal (Sweden); Lausmaa, Jukka [BIOMATCELL Vinn Excellence Center of Biomaterials and Cell Therapy, Gothenburg (Sweden); Department of Chemistry, Materials and Surfaces, SP Technical Research Institute of Sweden, Borås (Sweden); Palmquist, Anders [BIOMATCELL Vinn Excellence Center of Biomaterials and Cell Therapy, Gothenburg (Sweden); Department of Biomaterials, Sahlgrenska Academy at the University of Gothenburg, Gothenburg (Sweden)

    2015-10-30

    Highlights: • A route for coating complex shaped electron beam melted implants is presented. • Biomimetic HA coatings were deposited on CoCr alloys using a solution method. • Deposited biomimetic coating was partially crystalline, slightly calcium deficient. • Coating morphology was plate-like with crystallites forming roundish flowers. • Present coating procedure could be useful for porous implants made by EBM. - Abstract: The aim of this work was to study the feasibility to use a biomimetic method to prepare biomimetic hydroxyapatite (HA) coatings on CoCr substrates with short soaking times and to characterize the properties of such coatings. A second objective was to investigate if the coatings could be applied to porous CoCr implants manufactured by electron beam melting (EBM). The coating was prepared by immersing the pretreated CoCr substrates and EBM implants into the phosphate-buffered solution with Ca{sup 2+} in sealed plastic bottles, kept at 60 °C for 3 days. The formed coating was partially crystalline, slightly calcium deficient and composed of plate-like crystallites forming roundish flowers in the size range of 300–500 nm. Cross-section imaging showed a thickness of 300–500 nm. In addition, dissolution tests in Tris–HCl up to 28 days showed that a substantial amount of the coating had dissolved, however, undergoing only minor morphological changes. A uniform coating was formed within the porous network of the additive manufactured implants having similar thickness and morphology as for the flat samples. In conclusion, the present coating procedure allows coatings to be formed on CoCr and could be used for complex shaped, porous implants made by additive manufacturing.

  20. Non-viral bone morphogenetic protein 2 transfection of rat dental pulp stem cells using calcium phosphate nanoparticles as carriers.

    NARCIS (Netherlands)

    Yang, X.; Walboomers, X.F.; Dolder, J. van den; Yang, F.; Bian, Z.; Fan, M.; Jansen, J.A.

    2008-01-01

    Calcium phosphate nanoparticles have shown potential as non-viral vectors for gene delivery. The aim of this study was to induce bone morphogenetic protein (Bmp)2 transfection in rat dental pulp stem cells using calcium phosphate nanoparticles as a gene vector and then to evaluate the efficiency and

  1. Effect of calcium phosphate crystals induced by uremic serum on calcification of human aortic smooth muscle cells

    Institute of Scientific and Technical Information of China (English)

    刘曜蓉

    2013-01-01

    Objective To investigate the impact of calcium phosphate crystals induced by uremic serum on calcification of human aortic smooth muscle cells (HASMCs) .Methods Uremic serum was incubated at 37℃for 3days.Calcium phosphate crystals and uremic supernatant were isolated from uremic serum by ultracentrifugation.

  2. Non-viral bone morphogenetic protein 2 transfection of rat dental pulp stem cells using calcium phosphate nanoparticles as carriers.

    NARCIS (Netherlands)

    Yang, X.; Walboomers, X.F.; Dolder, J. van den; Yang, F.; Bian, Z.; Fan, M.; Jansen, J.A.

    2008-01-01

    Calcium phosphate nanoparticles have shown potential as non-viral vectors for gene delivery. The aim of this study was to induce bone morphogenetic protein (Bmp)2 transfection in rat dental pulp stem cells using calcium phosphate nanoparticles as a gene vector and then to evaluate the efficiency and

  3. Electrostatic spray deposition (ESD) of calcium phosphate coatings, an in vitro study with osteoblast-like cells.

    NARCIS (Netherlands)

    Siebers, M.C.; Walboomers, X.F.; Leeuwenburgh, S.C.G.; Wolke, J.G.C.; Jansen, J.A.

    2004-01-01

    Electrostatic spray deposition (ESD) is a recently developed technique to deposit a calcium phosphate (CaP) coating upon substrates. With this technique, an organic solvent containing calcium and phosphate is pumped through a nozzle. Between the nozzle and substrate a high voltage is applied. As a

  4. Mapping calcium phosphate activated gene networks as a strategy for targeted osteoinduction of human progenitors.

    Science.gov (United States)

    Eyckmans, Jeroen; Roberts, Scott J; Bolander, Johanna; Schrooten, Jan; Chen, Christopher S; Luyten, Frank P

    2013-06-01

    Although calcium phosphate-containing biomaterials are promising scaffolds for bone regenerative strategies, the osteoinductive capacity of such materials is poorly understood. In this study, we investigated whether endogenous mechanisms of in vivo calcium phosphate-driven, ectopic bone formation could be identified and used to induce enhanced differentiation in vitro of the same progenitor population. To accomplish this, human periosteum derived cells (hPDCs) were seeded on hydroxyapatite/collagen scaffolds (calcium phosphate rich matrix or CPRM), or on decalcified scaffolds (calcium phosphate depleted matrix or CPDM), followed by subcutaneous implantation in nude mice to trigger ectopic bone formation. In this system, osteoblast differentiation occurred in CPRM scaffolds, but not in CPDM scaffolds. Gene expression was assessed by human full-genome microarray at 20 h after seeding, and 2, 8 and 18 days after implantation. In both matrices, implantation of the cell constructs triggered a similar gene expression cascade, however, gene expression dynamics progressed faster in CPRM scaffolds than in CPDM scaffolds. The difference in gene expression dynamics was associated with differential activation of hub genes and molecular signaling pathways related to calcium signaling (CREB), inflammation (TNFα, NFkB, and IL6) and bone development (TGFβ, β-catenin, BMP, EGF, and ERK signaling). Starting from this set of pathways, a growth factor cocktail was developed that robustly enhanced osteogenesis in vitro and in vivo. Taken together, our data demonstrate that through the identification and subsequent stimulation of genes, proteins and signaling pathways associated with calcium phosphate mediated osteoinduction, a focused approach to develop targeted differentiation protocols in adult progenitor cells can be achieved.

  5. Factors influencing calcium phosphate cement shelf-life.

    Science.gov (United States)

    Gbureck, Uwe; Dembski, Sofia; Thull, Roger; Barralet, Jake E

    2005-06-01

    Long-term stability during storage (shelf-life) is one major criterion for the use of a material as medical device. This study aimed to investigate the ageing process of beta-tricalcium phosphate/monocalcium phosphate cement powders when stored in sealed containers at ambient conditions. This kind of cement type is of interest because it is forming dicalcium phosphate dihydrate (brushite) when set, which is in contrast to hydroxyapatite resorbable in physiological conditions. The stability of cements was checked by either measuring the phase composition of powders as well as the setting time and compressive strength when mixed with sodium citrate as liquid. Critical factors influencing ageing were found to be temperature, humidity and the mixing regime of the powders. Mechanically mixed cement powders which were stored in normal laboratory atmosphere (22 degrees C, 60% rel. humidity) converted to dicalcium phosphate anhydrous (monetite) within a few days; this could be mechanistically related to a dissolution/precipitation process since humidity condensed on the particles' surfaces and acted as reaction medium. Various storage conditions were found to be effective in prolonging cement stability which were in order of effectiveness: adding solid citric acid retardant>dry argon atmosphere=gentle mixing (minimal mechanical energy input) low temperature.

  6. Effects of Silicate, Phosphate, and Calcium on the Stability of Aldopentoses.

    Science.gov (United States)

    Nitta, Sakiko; Furukawa, Yoshihiro; Kakegawa, Takeshi

    2016-06-01

    Ribose is an important constituent of RNA: ribose connects RNA bases and forms a strand of sugar phosphates. Accumulation of ribose on prebiotic Earth was difficult because of its low stability. Improvement in the yield of ribose by the introduction of borate or silicate in a formose-like reaction has been proposed. The effects of borates have been further analyzed and confirmed in subsequent studies. Nonetheless, the effects of silicates and phosphates remain unclear. In the present study, we incubated aldopentoses in a highly alkaline aqueous solution at a moderate temperature to determine the effects of silicate or phosphate on the degradation rates of ribose and its isomeric aldopentoses. The formation of a complex of silicate (or phosphate) with ribose was also analyzed in experiments with (29)Si and (31)P nuclear magnetic resonance (NMR). We found that silicate or phosphate complexes of ribose were not detectable under our experimental conditions. The stability of ribose and lyxose improved after addition of 40-fold molar excess (relative to a pentose) of sodium silicate or sodium phosphate to the alkaline solution. The stability was not improved further when an 80-fold molar excess of sodium silicate or sodium phosphate was added. Calcium was removed from these solutions by precipitation of calcium salts. The drop in Ca(2+) concentration might have improved the stability of ribose and lyxose, which are susceptible to aldol addition. The improvement of ribose stability by the removal of Ca(2+) and by addition of silicate or phosphate was far smaller than the improvement by borate. Furthermore, all aldopentoses showed similar stability in silicate- and phosphate-containing solutions. These results clearly show that selective stabilization of ribose by borate cannot be replaced by the effects of silicate or phosphate; this finding points to the importance of borate in prebiotic RNA formation.

  7. Preparation and characterization of a degradable magnesium phosphate bone cement.

    Science.gov (United States)

    Yu, Ying; Xu, Chao; Dai, Honglian

    2016-12-01

    A kind of degradable magnesium phosphate bone cement (MPBC) was fabricated by using the mixed powders of magnesium oxide (MgO), potassium dihydrogen phosphate (KH2PO4) and calcium dihydrogen phosphate (Ca(H2PO4)2.H2O). As MgKPO4, the main product of MgO and KH2PO4 was alkaline, the Ca(H2PO4)2.H2O was added to neutralize the alkali of the system. And the effects of Ca(H2PO4)2.H2O on the performance of MPBC were discussed. The results showed that the adding of Ca(H2PO4)2.H2O extended the setting time, which was about 6 min to 18 min. The compressive strength increased first and then decreased, and maximum value reached 31.2 MPa after setting for 24 h without any additional pressure. The MPBC was degradable in Tris-HCl solution, and the extracts of the cytotoxicity assay showed that the MPBC had good biocompatibility, indicating that the MPBC had good biodegradable and biocompatible properties.

  8. Synthesis, characterization, and in-vitro cytocompatibility of amorphous β-tri-calcium magnesium phosphate ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Satish S., E-mail: sss42@pitt.edu [Department of Chemical & Petroleum Engineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Roy, Abhijit, E-mail: abr20@pitt.edu [Department of Bioengineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Lee, Boeun, E-mail: bol11@pitt.edu [Department of Bioengineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Banerjee, Ipsita [Department of Chemical & Petroleum Engineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Kumta, Prashant N., E-mail: pkumta@pitt.edu [Department of Chemical & Petroleum Engineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Department of Bioengineering, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Center for Craniofacial Regeneration, University of Pittsburgh, Pittsburgh, PA 15261 (United States); Department of Mechanical Engineering and Materials Science, University of Pittsburgh, PA 15261 (United States)

    2016-10-01

    Biphasic mixtures of crystalline β-tricalcium magnesium phosphate (β-TCMP) and an amorphous calcium magnesium phosphate have been synthesized and reported to support enhanced hMSC differentiation in comparison to β-tricalcium phosphate (β-TCP) due to the release of increased amounts of bioactive ions. In the current study, completely amorphous β-TCMP has been synthesized which is capable of releasing increased amounts of Mg{sup 2+} and PO{sub 4}{sup 3−} ions, rather than a biphasic mixture as earlier reported. The amorphous phase formed was observed to crystallize between temperatures of 400–600 °C. The scaffolds prepared with amorphous β-TCMP were capable of supporting enhanced hMSC proliferation and differentiation in comparison to commercially available β-TCP. However, a similar gene expression of mature osteoblast markers, OCN and COL-1, in comparison to biphasic β-TCMP was observed. To further study the role of Mg{sup 2+} and PO{sub 4}{sup 3−} ions in regulating hMSC osteogenic differentiation, the capability of hMSCs to mineralize in growth media supplemented with Mg{sup 2+} and PO{sub 4}{sup 3−} ions was studied. Interestingly, 5 mM PO{sub 4}{sup 3−} supported mineralization while the addition of 5 mM Mg{sup 2+} to 5 mM PO{sub 4}{sup 3−} inhibited mineralization. It was therefore concluded that the release of Ca{sup 2+} ions from β-TCMP scaffolds also plays a role in regulating osteogenic differentiation on these scaffolds and it is noted that further work is required to more accurately determine the exact role of Mg{sup 2+} in regulating hMSC osteogenic differentiation. - Highlights: • Synthesis of amorphous Mg containing beta tricalcium phosphate ceramics • Amorphous beta TCMP supports enhanced hMSC proliferation and differentiation. • Amorphous beta TCMP shows comparable OCN and COL-1 expression to biphasic TCMP. • Presence of 5 mM Mg{sup 2+} and PO{sub 4}{sup 3−} ions in growth media inhibits hMSC mineralization.

  9. Ectopic osteoid and bone formation by three calcium-phosphate ceramics in rats, rabbits and dogs

    NARCIS (Netherlands)

    Wang, Liao; Zhang, B.; Bao, C.; Habibovic, P.; Hu, J.; Zhang, Xingdong

    2014-01-01

    Calcium phosphate ceramics with specific physicochemical properties have been shown to induce de novo bone formation upon ectopic implantation in a number of animal models. In this study we explored the influence of physicochemical properties as well as the animal species on material-induced ectopic

  10. PLGA microsphere/calcium phosphate cement composites for tissue engineering: in vitro release and degradation characteristics.

    NARCIS (Netherlands)

    Habraken, W.J.E.M.; Wolke, J.G.C.; Mikos, A.G.; Jansen, J.A.

    2008-01-01

    Bone cements with biodegradable poly(lactic-co-glycolic acid) (PLGA) microspheres have already been proven to provide a macroporous calcium phosphate cement (CPC) during in situ microsphere degradation. Furthermore, in vitro/in vivo release studies with these PLGA microsphere/CPC composites (PLGA/CP

  11. Cost containment using cysteine HCl acidification to increase calcium/phosphate solubility in hyperalimentation solutions.

    Science.gov (United States)

    Schmidt, G L; Baumgartner, T G; Fischlschweiger, W; Sitren, H S; Thakker, K M; Cerda, J J

    1986-01-01

    The purpose of this study was to determine if (1) the calcium/phosphate insoluble product was inversely related to pH [when cysteine HC1 (CH) was added as neonatal supplementation at 0.5 mM/kg/day to hyperalimentation (HAL) solutions] and (2) the potential cost savings to the hospital. The pH of the HAL solutions was adjusted by adding various amounts of CH to the HAL solution. HAL solutions containing 27 mEq of calcium/liter and 30 mEq (15 mM) of phosphate/liter were compounded. Ten-milliliter aliquots were analyzed at 0, 12, 24, and 48 hr. All samples (n = 56) were filtered (0.22 mu), viewed with 7-10,000 X magnification scanning electron microscopy, and qualitatively analyzed with a Philips Energy Dispersive X-Ray Analysis System equipped with a SW9100 Microprocessor. Calcium/phosphate insoluble product was present in the 0-, 12-, 24-, and 48-hr samples from the CH-free solutions. The solutions containing 759 mg (4.17 mM)/liter of CH however, remained free of precipitant. This investigation demonstrated that addition of CH to HAL can foster significant cost containment (projected $82,000/yr tangible hospital savings) by the elimination of current calcium/phosphate separation procedures for neonates on parenteral nutrition.

  12. Bioactivity and Surface Reactivity of RF-sputtered Calcium Phosphate Thin Films

    NARCIS (Netherlands)

    Wal, Edwin van der

    2003-01-01

    Calcium phosphates (CaP) are known to be bioactive, i.e. able to bond to bone. This makes CaPs very suitable to be aplied as thin coatings on bone-implants. In this work we studied the physicochemical behaviour of CaP coatings applied with radio frequency (RF) magnetron sputtering, a deposition tech

  13. Dense and porous titanium substrates with a biomimetic calcium phosphate coating

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, A.A., E-mail: aantunesr@yahoo.com.br [Powder Technology Laboratory, Materials Processing and Characterization Division, National Institute of Technology, No. 82 Venezuela Avenue, Room 602, 20081-312 Rio de Janeiro, RJ (Brazil); Balestra, R.M. [Powder Technology Laboratory, Materials Processing and Characterization Division, National Institute of Technology, No. 82 Venezuela Avenue, Room 602, 20081-312 Rio de Janeiro, RJ (Brazil); Rocha, M.N. [Metallurgical and Materials Engineering Program, COPPE, Federal University of Rio de Janeiro, P.O. Box 68505, 21941-972 Rio de Janeiro, RJ (Brazil); Peripolli, S.B. [Materials Metrology Division, National Institute of Metrology, Normalization and Quality, No. 50 Nossa Senhora das Gracas Street, Building 3, 25250-020 Duque de Caxias, RJ (Brazil); Andrade, M.C. [Polytechnic Institute of Rio de Janeiro, Rio de Janeiro State University, s/n, Alberto Rangel Street, 28630-050 Nova Friburgo, RJ (Brazil); Pereira, L.C. [Metallurgical and Materials Engineering Program, COPPE, Federal University of Rio de Janeiro, P.O. Box 68505, 21941-972 Rio de Janeiro, RJ (Brazil); Oliveira, M.V. [Powder Technology Laboratory, Materials Processing and Characterization Division, National Institute of Technology, No. 82 Venezuela Avenue, Room 602, 20081-312 Rio de Janeiro, RJ (Brazil)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer A biomimetic coating method with simplified solution is proposed. Black-Right-Pointing-Pointer Titanium substrates are submitted to chemical and heat treatments. Black-Right-Pointing-Pointer Titanium substrates are coated with biocompatible calcium phosphate phases. Black-Right-Pointing-Pointer The simplified solution shows potential to be applied as a coating technique. - Abstract: The present work studied a biomimetic method using a simplified solution (SS) with calcium and phosphorus ions for coating titanium substrates, in order to improve their bioactivity. Commercially pure titanium dense sheet, microporous and macroporous titanium samples, both produced by powder metallurgy, were treated in NaOH solution followed by heat-treating and immersed in SS for 7, 14 or 21 days. The samples characterization was performed by quantitative metallographic analysis, confocal scanning optical microscopy, scanning electron microscopy, energy dispersive spectroscopy and low angle X-ray diffraction. The results showed coatings with calcium phosphate precipitation in all samples, with globular or plate-like morphology, typical of hydroxyapatite and octacalcium phosphate, respectively, indicating that the solution (SS) has potential for coating titanium substrates. In addition, the different surfaces of substrates had an effect on the formed calcium phosphate phase and thickness of coatings, depending on the substrate type and imersion time in the simplified solution.

  14. Bioactivity and Surface Reactivity of RF-sputtered Calcium Phosphate Thin Films

    NARCIS (Netherlands)

    Wal, Edwin van der

    2003-01-01

    Calcium phosphates (CaP) are known to be bioactive, i.e. able to bond to bone. This makes CaPs very suitable to be aplied as thin coatings on bone-implants. In this work we studied the physicochemical behaviour of CaP coatings applied with radio frequency (RF) magnetron sputtering, a deposition

  15. In vivo performance of microstructured calcium phosphate formulated in novel water-free carriers

    NARCIS (Netherlands)

    Davison, N.L.; Yuan, H.; Bruijn, de J.D.; Barrere-de Groot, F.YF.

    2012-01-01

    Osteoinductive calcium phosphate (CaP) ceramics can be combined with polymeric carriers to make shapeable bone substitutes as an alternative to autologous bone; however, carriers containing water may degrade the ceramic surface microstructure, which is crucial to bone formation. In this study five n

  16. Novel tea polyphenol-modified calcium phosphate nanoparticle and its remineralization potential

    NARCIS (Netherlands)

    He, L.; Deng, D.; Zhou, X.; Cheng, L.; ten Cate, J.M.; Li, J.; Li, X.; Crielaard, W.

    2015-01-01

    Tea polyphenols (TP) are not only potent antimicrobial and antioxidant agents but also effective modifiers in the formation of nanosized crystals. Since nano-hydroxyapatite (n-HA) is known to enhance remineralization of dental hard tissue, our aims were to synthesize nanosized calcium phosphate part

  17. Influence of polymer addition on the mechanical properties of a premixed calcium phosphate cement.

    Science.gov (United States)

    Engstrand, Johanna; Persson, Cecilia; Engqvist, Håkan

    2013-01-01

    Premixed calcium phosphate cements can reduce handling complications that are associated with the mixing of cements in the operating room. However, to extend the clinical indication of ceramic cements their mechanical properties need to be further improved. The incorporation of a polymeric material with intrinsically high tensile properties could possibly assist in increasing the mechanical properties of calcium phosphate cement. In this study polymer microparticles made from poly(lactid-co-glycolide) plasticised with poly(ethylene glycol) 400 (PLGA/PEG microparticles) were added in amounts of up to 5 wt% to a premixed acidic calcium phosphate cement. The PLGA/PEG microparticles added undergo a shape transformation at 37 °C, which could give a better integration between polymer microparticles and ceramic cement compared with polymer microparticles lacking this property. The results showed that the incorporation of 1.25 wt% PLGA/PEG microparticles increased the compressive strength by approximately 20% up to 15.1 MPa while the diametral tensile strength was kept constant. The incorporation of PLGA/PEG microparticles increased the brushite to monetite ratio after setting compared with pure ceramic cements. In conclusion, small amounts of PLGA/PEG microparticles can be incorporated into premixed acidic calcium phosphate cement and increase their mechanical properties, which could lead to increased future applications.

  18. Evaluation of a porosity measurement method for wet calcium phosphate cements.

    Science.gov (United States)

    Ajaxon, Ingrid; Maazouz, Yassine; Ginebra, Maria-Pau; Öhman, Caroline; Persson, Cecilia

    2015-11-01

    The porosity of a calcium phosphate cement is a key parameter as it affects several important properties of the cement. However, a successful, non-destructive porosity measurement method that does not include drying has not yet been reported for calcium phosphate cements. The aim of this study was to evaluate isopropanol solvent exchange as such a method. Two different types of calcium phosphate cements were used, one basic (hydroxyapatite) and one acidic (brushite). The cements were allowed to set in an aqueous environment and then immersed in isopropanol and stored under three different conditions: at room temperature, at room temperature under vacuum (300 mbar) or at 37℃. The specimen mass was monitored regularly. Solvent exchange took much longer time to reach steady state in hydroxyapatite cements compared to brushite cements, 350 and 18 h, respectively. Furthermore, the immersion affected the quasi-static compressive strength of the hydroxyapatite cements. However, the strength and phase composition of the brushite cements were not affected by isopropanol immersion, suggesting that isopropanol solvent exchange can be used for brushite calcium phosphate cements. The main advantages with this method are that it is non-destructive, fast, easy and the porosity can be evaluated while the cements remain wet, allowing for further analysis on the same specimen.

  19. Influence of polymer addition on the mechanical properties of a premixed calcium phosphate cement

    Science.gov (United States)

    Engstrand, Johanna; Persson, Cecilia; Engqvist, Håkan

    2013-01-01

    Premixed calcium phosphate cements can reduce handling complications that are associated with the mixing of cements in the operating room. However, to extend the clinical indication of ceramic cements their mechanical properties need to be further improved. The incorporation of a polymeric material with intrinsically high tensile properties could possibly assist in increasing the mechanical properties of calcium phosphate cement. In this study polymer microparticles made from poly(lactid-co-glycolide) plasticised with poly(ethylene glycol) 400 (PLGA/PEG microparticles) were added in amounts of up to 5 wt% to a premixed acidic calcium phosphate cement. The PLGA/PEG microparticles added undergo a shape transformation at 37 °C, which could give a better integration between polymer microparticles and ceramic cement compared with polymer microparticles lacking this property. The results showed that the incorporation of 1.25 wt% PLGA/PEG microparticles increased the compressive strength by approximately 20% up to 15.1 MPa while the diametral tensile strength was kept constant. The incorporation of PLGA/PEG microparticles increased the brushite to monetite ratio after setting compared with pure ceramic cements. In conclusion, small amounts of PLGA/PEG microparticles can be incorporated into premixed acidic calcium phosphate cement and increase their mechanical properties, which could lead to increased future applications. PMID:24270588

  20. Trabecular bone response to injectable calcium phosphate (Ca-P) cement.

    NARCIS (Netherlands)

    Ooms, E.M.; Wolke, J.G.C.; Waerden, J.P.C.M. van der; Jansen, J.A.

    2002-01-01

    The aim of this study was to investigate the physicochemical, biological, and handling properties of a new developed calcium phosphate (Ca-P) cement when implanted in trabecular bone. Ca-P cement consisting of a powder and a liquid phase was implanted as a paste into femoral trabecular bone of goats

  1. Bone response to fast-degrading, injectable calcium phosphate cements containing PLGA microparticles

    NARCIS (Netherlands)

    Lanao, R.P.; Leeuwenburgh, S.C.G.; Wolke, J.G.C.; Jansen, J.A.

    2011-01-01

    Apatitic calcium phosphate cements (CPC) are frequently used to fill bone defects due to their favourable clinical handling and excellent bone response, but their lack of degradability inhibits complete bone regeneration. In order to render these injectable CaP cements biodegradable, hollow microsph

  2. The calcium-paracaseinate-phosphate-complex under conditions similar to those in cheese

    NARCIS (Netherlands)

    Monib, A.M.M.F.

    1962-01-01

    The complex of calcium-paracaseinate-phosphate is the matrix substance of cheese. The changes it undergoes during maturing determines many characteristics of the finished product.

    The preliminary studies of the effect of pH and sodium chloride on the swelling and solubility of the

  3. Calcium phosphate coating on magnesium alloy by biomimetic method :Investigation of morphology ,composition and formation process

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Magnesium alloy has similar mechanical properties with natural bone and can degrade via corrosion in the electrolytic environment of the human body.Calcium phosphate has been proven to possess bioactivity and bone inductivity.In order to integrate both advantages,calcium phosphate coating was fabricated on magnesium alloy by a biomimetic method.Supersaturated calcification solutions (SCSs) with different Ca/P ratio and C1- concentration were used as mimetic solutions.The morphology,composition and formation process of the coating were studied with scanning electron microscopy (SEM),energy dispersive spectrometer (EDS),Fourier transformed infrared spectroscopy (FTIR) and X-ray diffraction (XRD).The results show that a uniform calcium phosphate coating was observed on magnesium alloy,the properties of which could be adjusted by the SCSs with different Ca/P ratio.The formation process of the coating was explored by immersing magnesium alloy in SCSs with different Cl- concentration which could adjust the hydrogen production.According to SEM results,the hydrogen bubbles were associated with the formation of grass-like and flower-like coating morphologies.In conclusion,the biomimetic method was effective to form calcium phosphate coating on magnesium alloy and the morphology and composition of the coating could be accommodated by the Ca/P ratio and Cl- concentration in SCSs.

  4. Controlling surface microstructure of calcium phosphate ceramic from random to custom-design

    NARCIS (Netherlands)

    Wang, Liao; Luo, Xiaoman; Barbieri, D.; Bao, Chongyun; Yuan, Huipin

    2014-01-01

    Calcium phosphate ceramics have long been studied as bone graft substitutes due to their similarity with the mineral constitute of bone and teeth, excellent biocompatibility and bioactivity. Chemical composition, macrostructure and surface microstructure are believed to be important for the bone for

  5. Dietary Calcium Phosphate Stimulates Intestinal Lactobacilli and decreases the severity of a salmonella infection in rats

    NARCIS (Netherlands)

    Bovee-Oudenhoven, I.M.; Wissink, M.L.; Wouters, J.T.; Meer, van der R.

    1999-01-01

    We have shown recently that dietary calcium phosphate (CaPi) has a trophic effect on the intestinal microflora and strongly protects against salmonella infection. It was speculated that precipitation by CaPi of intestinal surfactants, such as bile acids and fatty acids, reduced the cytotoxicity of i

  6. Analysis of integrin expression in U2OS cells cultured on various calcium phosphate ceramic substrates.

    NARCIS (Netherlands)

    Ruijter, J.E. de; Brugge, P.J. ter; Dieudonne, S.C.; Vliet, S.J. van; Torensma, R.; Jansen, J.A.

    2001-01-01

    Earlier we observed that calcium phosphate (Ca-P)-coated implant substrates stimulated the differentiation of osteoblast-like cells compared to uncoated substrates. This suggests that this difference in osteogenic induction is due to the chemical composition of the substratum. We hypothesized that C

  7. Biocompatibility and degradation of poly(DL-lactic-co-glycolic acid)/calcium phosphate cement composites

    NARCIS (Netherlands)

    Ruhe, P.Q.; Hedberg, E.L.; Padron, N.T.; Spauwen, P.H.M.; Jansen, J.A.; Mikos, A.G.

    2005-01-01

    Injectable calcium phosphate (Ca-P) cement materials exhibit favorable osteocompatible behavior but are resorbed slowly because of a lack of a bone ingrowth-enabling macroporosity. In this study, poly(DL-lactic-co-glycolic acid) (PLGA) microparticles (average size 66 +/- 25 microm) were incorporated

  8. Incorporation of biodegradable electrospun fibers into calcium phosphate cement for bone regeneration.

    NARCIS (Netherlands)

    Zuo, Y.; Yang, F.; Wolke, J.G.C.; Li, Yubao; Jansen, J.A.

    2010-01-01

    Inherent brittleness and slow degradation are the major drawbacks for the use of calcium phosphate cements (CPCs). To address these issues, biodegradable ultrafine fibers were incorporated into the CPC in this study. Four types of fibers made of poly(epsilon-caprolactone) (PCL) (PCL12: 1.1 microm, P

  9. A study about some phosphate derivatives as inhibitors of calcium oxalate crystal growth

    Science.gov (United States)

    Grases, F.; March, P.

    1989-08-01

    The kinetic of crystal growth of calcium oxalate monohydrate seed crystals were investigated potentiometrically in the presence of several phosphate derivatives, D-fructose-1,6-diphosphate, pyrophosphate, methylene diphosphonate and phytate, and it was found that in some cases they strongly inhibited crystal growth. The inhibitory action of the different substances assayed was comparatively evaluated.

  10. FORMATION OF PHOSPHATE-CONTAINING CALCIUM-FLUORIDE AT THE EXPENSE OF ENAMEL, HYDROXYAPATITE AND FLUORAPATITE

    NARCIS (Netherlands)

    CHRISTOFFERSEN, J; CHRISTOFFERSEN, MR; ARENDS, J; LEONARDSEN, ES

    1995-01-01

    During the caries process complex reactions involving calcium, phosphate, hydrogen and fluoride ions as main species take place. In this study the precipitation and dissolution reactions occurring in suspensions of enamel, hydroxyapatite (HAP) and fluorapatite (FAP) on addition of fluoride were inve

  11. Influence of surface microstructure and chemistry on osteoinduction and osteoclastogenesis by biphasic calcium phosphate discs.

    NARCIS (Netherlands)

    Davison, N.L.; Su, J.; Yuan, H.; Beucken, J.J.J.P van den; Bruijn, J.D. de; rrere-de Groot, F. Ba

    2015-01-01

    It has been reported that surface microstructural dimensions can influence the osteoinductivity of calcium phosphates (CaPs), and osteoclasts may play a role in this process. We hypothesised that surface structural dimensions of

  12. FORMATION OF PHOSPHATE-CONTAINING CALCIUM-FLUORIDE AT THE EXPENSE OF ENAMEL, HYDROXYAPATITE AND FLUORAPATITE

    NARCIS (Netherlands)

    CHRISTOFFERSEN, J; CHRISTOFFERSEN, MR; ARENDS, J; LEONARDSEN, ES

    1995-01-01

    During the caries process complex reactions involving calcium, phosphate, hydrogen and fluoride ions as main species take place. In this study the precipitation and dissolution reactions occurring in suspensions of enamel, hydroxyapatite (HAP) and fluorapatite (FAP) on addition of fluoride were

  13. Introduction of enzymatically degradable poly(trimethylene carbonate) microspheres into an injectable calcium phosphate cement

    NARCIS (Netherlands)

    Habraken, Wouter J. E. M.; Zhang, Zheng; Wolke, Joop G. C.; Grijpma, Dirk W.; Mikos, Antonios G.; Feijen, Jan; Jansen, John A.

    2008-01-01

    Poly(trimethylene carbonate) (PTMC) is an enzymatically degradable polyester with rubber-like properties. Introduction of this polymer into an injectable calcium phosphate bone cement can therefore be used to introduce macroporosity into the cement for tissue engineering purposes as well as to impro

  14. Injectable PLGA microsphere/calcium phosphate cements: physical properties and degradation characteristics.

    NARCIS (Netherlands)

    Habraken, W.J.E.M.; Wolke, J.G.C.; Mikos, A.G.; Jansen, J.A.

    2006-01-01

    Calcium phosphate (CaP) cements show an excellent biocompatibility and often have a high mechanical strength, but in general degrade relatively slow. To increase degradation rates, macropores can be introduced into the cement, e.g., by the inclusion of biodegradable microspheres into the cement. The

  15. Introduction of enzymatically degradable poly(trimethylene carbonate) microspheres into an injectable calcium phosphate cement.

    NARCIS (Netherlands)

    Habraken, W.J.E.M.; Zhang, Z.; Wolke, J.G.C.; Grijpma, D.W.; Mikos, A.G.; Feijen, J.; Jansen, J.A.

    2008-01-01

    Poly(trimethylene carbonate) (PTMC) is an enzymatically degradable polyester with rubber-like properties. Introduction of this polymer into an injectable calcium phosphate bone cement can therefore be used to introduce macroporosity into the cement for tissue engineering purposes as well as to impro

  16. Biocompatibility and degradation of poly(DL-lactic-co-glycolic acid)/calcium phosphate cement composites

    NARCIS (Netherlands)

    Ruhe, P.Q.; Hedberg, E.L.; Padron, N.T.; Spauwen, P.H.M.; Jansen, J.A.; Mikos, A.G.

    2005-01-01

    Injectable calcium phosphate (Ca-P) cement materials exhibit favorable osteocompatible behavior but are resorbed slowly because of a lack of a bone ingrowth-enabling macroporosity. In this study, poly(DL-lactic-co-glycolic acid) (PLGA) microparticles (average size 66 +/- 25 microm) were incorporated

  17. Calcium phosphate holmium-166 ceramic to addition in bone cement: synthesis and characterization

    Energy Technology Data Exchange (ETDEWEB)

    Donanzam, Blanda A.; Campos, Tarcisio P.R., E-mail: campos@nuclear.ufmg.b [Universidade do Federal de Minas Gerais (DEN/UFMG), Belo Horizonte, MG (Brazil). Escola de Engenharia. Dept. de Engenharia Nuclear; Dalmazio, Ilza; Valente, Eduardo S., E-mail: id@cdtn.b, E-mail: valente@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2011-07-01

    Spine metastases are a common and painful complication of cancer. The treatment often consists of bone cement injection (vertebroplasty or kyphoplasty) within vertebral body for vertebrae stabilization, followed by external beam radiation therapy. Recently, researchers introduced the concept of radioactive bone cement for spine tumors therapy. Then, investigations about bioactive and radioactive materials became interesting. In this study, we present the synthesis of calcium phosphate incorporated holmium (CaP-Ho) via sol-gel technique, and its characterization by XRD, FT-IR, NA and SEM. Results showed a multiphasic bioceramic composed mainly of hydroxyapatite, {beta}-tricalcium phosphate, holmium phosphate and traces of calcium pyrophosphate. Furthermore, the nuclide Ho-166 was the major radioisotope produced. Despite that, the radioactive bioceramic CaP-{sup 166}Ho must be investigated in clinical trials to assure its efficacy and safety on spine tumors treatment (author)

  18. Processing and properties of calcium phosphates bioceramics by hot isostatic pressing

    Directory of Open Access Journals (Sweden)

    Boilet Laurent

    2013-11-01

    Full Text Available Stoichiometric β-tricalcium phosphate (β-TCP, hydroxyapatite (HA and biphasic calcium phosphate (TCP/HA 60/40 %wt, BCP40 powders were synthesized by chemical precipitation of aqueous solutions of diammonium phosphate and calcium nitrate. After a calcination treatment and a milling step, powders were shaped by slip-casting. The sintering temperature effect on the density and the average grain size was investigated. By natural sintering, densities between 98 and 99.8% were obtained. Hot Isostatic Pressing (HIP treatment was carried out after a pre-sintering of these materials. Transparent or translucent samples were obtained, indicating a relative density very close to the theoretical value (>99.9%. Mechanical properties (three-point bending strength, fracture toughness, Young's modulus and Vickers hardness were measured on hipped materials with similar grain size (∼0.7μm.

  19. Use of alkaline calcium salts as phosphate binder in uremic patients.

    Science.gov (United States)

    Fournier, A; Morinière, P; Ben Hamida, F; el Esjer, N; Shenovda, M; Ghazali, A; Bouzernidj, M; Achard, J M; Westeel, P F

    1992-10-01

    In order to prevent aluminum toxicity induced by the association of aluminum phosphate binder with 1 alpha(OH) vitamin D3 derivatives and the use of deferoxamine with its own hazards to diagnose and treat this toxicity, we have shown in 1982 that it was possible to replace the iatrogenic association of aluminum phosphate binder with 1 alpha OH vitamin D derivatives by oral calcium carbonate taken with the meals in order to bind phosphate and correct the negative calcium balance. This led to the disappearance of the crippling aluminic osteomalacia and adynamic bone diseases in our center. The effectiveness of CaCO3 without 1 alpha(OH)D3 derivatives in the control of hyperparathyroidism in dialysis patients has been proven by the appearance in four patients of our dialysis population of an histological idiopathic adynamic bone disease associated with relative hypoparathyroidism, and by the finding that more than 50% of our dialysis population treated by this sole treatment have plasma concentration of intact PTH below twice the upper limit of normal (that is, the threshold above which only significant histological osteitis fibrosa is observed). Besides the compliance problem, the limit of CaCO3 is the occurrence of hypercalcemia which occurs in about 8% of the measurements. Since calcium acetate binds twice as much phosphate for the same dose of elemental calcium as CaCO3, its use has been recommended. However, clinical experience has shown that in spite of the fact that half the dose of calcium element given as acetate does actually control predialysis plasma phosphate as well as CaCO3, the incidence of hypercalcemia is not decreased, probably because calcium availability at the alkaline pH of the intestine is much greater with Ca acetate. When hypercalcemia is frequent (and not explained by autonomized hyperparathyroidism, adynamic bone disease, overtreatment with vitamin D, granulomatosis or neoplasia) it is necessary either to decrease the dose of calcium and

  20. Phase stability of silver particles embedded calcium phosphate bioceramics

    Indian Academy of Sciences (India)

    Brajendra Singh; Samayendra Kumar; Naresh Saha; Bikramjit Basu; Rajeev Gupta

    2015-04-01

    In this paper, we report the compositional variation-dependent phase stability of hydroxyapatite (Ca10(PO4)6(OH)2) on doping with silver. The transformation of hydroxyapatite to (/) tricalcium phosphate phases during sintering has been explored using Raman spectroscopy and X-ray diffraction techniques. The optical absorption spectroscopy analysis reveals the presence of Ag+ ions at low doping levels. As the doping increases, abundance of Ag particles is enhanced.

  1. Primary osteoporosis prophylaxis with different calcium preparations

    Directory of Open Access Journals (Sweden)

    N. V. Toroptsova

    2005-01-01

    Full Text Available Objective. To assess efficacy of different modes of management in women with osteopenia. Material and methods. 190 women with osteopenia of spine and/or femoral neck aged 50 to 70 years (mean 60,6±5 years were followed up during a year. Different modes of prophylaxis were applied. 59 pts of group 1 received Calcium D3 Nicomed 2 tablets a day, 25 pts of group 2 - Vitrum Osteomag 2 tablets a day, 46 pts of group 3 - calcium carbonate 2500 mg/day, 60 pts of control group received recommendations about diet and physical activity. Results. 3,5% from 114 pts examined had normal 25(OHD blood level while 23% showed deficiency of vitamin D. Mean calcium consumption with milk products was 350 mg/day. Bone mineral density (BMD significantly increased on 1,6-1% in pts older than 60 years receiving Vitrum Osteomag and Calcium D3 Nicomed respectively while younger pts did not show such changes. BMD in pts olderthan 60 years receiving calcium carbonate increased on 0,5% but this difference was not significant. Tolerability of all 3 drugs was comparable.

  2. Modelling biological and chemically induced precipitation of calcium phosphate in enhanced biological phosphorus removal systems.

    Science.gov (United States)

    Barat, R; Montoya, T; Seco, A; Ferrer, J

    2011-06-01

    The biologically induced precipitation processes can be important in wastewater treatment, in particular treating raw wastewater with high calcium concentration combined with Enhanced Biological Phosphorus Removal. Currently, there is little information and experience in modelling jointly biological and chemical processes. This paper presents a calcium phosphate precipitation model and its inclusion in the Activated Sludge Model No 2d (ASM2d). The proposed precipitation model considers that aqueous phase reactions quickly achieve the chemical equilibrium and that aqueous-solid change is kinetically governed. The model was calibrated using data from four experiments in a Sequencing Batch Reactor (SBR) operated for EBPR and finally validated with two experiments. The precipitation model proposed was able to reproduce the dynamics of amorphous calcium phosphate (ACP) formation and later crystallization to hydroxyapatite (HAP) under different scenarios. The model successfully characterised the EBPR performance of the SBR, including the biological, physical and chemical processes.

  3. Procedure for the study of acidic calcium phosphate precursor phases in enamel mineral formation.

    Science.gov (United States)

    Siew, C; Gruninger, S E; Chow, L C; Brown, W E

    1992-02-01

    Considerable evidence suggests that an acidic calcium phosphate, such as octacalcium phosphate (OCP) or brushite, is involved as a precursor in enamel and other hard tissue formation. Additionally, there is in vitro evidence suggesting that fluoride accelerates and magnesium inhibits the hydrolysis of OCP to hydroxyapatite (OHAp). As the amount of OCP or brushite in enamel cannot be measured directly in the presence of an excess of hydroxyapatite, a procedure was developed that allows for their indirect in vivo quantification as pyrophosphate. This permits study of the effects of fluoride and magnesium ions on enamel mineral synthesis. Rat incisor calcium phosphate was labeled by intraperitoneal injection of NaH2(32)PO4. The rats were then subjected to various fluoride and magnesium treatments with subcutaneous implanted osmotic pumps. They were then killed at predetermined intervals; the nascent sections of the incisors were collected, cleaned, and pyrolyzed at 500 degrees C for 48 hours to convert acidic calcium phosphates to calcium pyrophosphate; the pyrophosphate was separated from orthophosphate by anion-exchange chromatography; and the resulting fractions were counted by liquid scintillation spectrometry. The activities of the pyro- and orthophosphate fractions were used to calculate the amount of acidic calcium phosphate present in the nascent mineral. The results demonstrated that the percentage of radioactive pyrophosphate in nascent incisors decreased with time, with increasing serum F- concentration, and with decreasing serum magnesium content. The technique described here should prove to be a powerful new tool for studying the effects of various agents on biological mineral formation.

  4. Extrusion-based, three-dimensional printing of calcium-phosphate scaffolds

    Science.gov (United States)

    Witek, Lukasz

    Small or large bone defects, can occur due to a variety of reasons: congenital disorders, infections, tumors, or traumas which can lead to significant disabilities. There is an assortment of bone grafting procedures, each having their own respective advantages and disadvantages and exhibiting certain essential characteristics. Among the available grafts, autogenous (autograft), allograft, xenograft, and alloplasts, all exhibit a minimum of two-thirds of the essential characteristics and have been proven useful in fully or partially repairing skeletal defects. However, different host-to-grafting material responses have been reported and should be taken into consideration when determining treatment options. A large range of physical and chemical properties can be achieved with calcium phosphate based materials, which possess two of the ideal characteristics for grafting procedures: osteoconduction and osseointegration. Calcium phosphate based scaffolds composed of hydroxyapatite (HA), beta-tri-calcium phosphate (beta-TCP), or a combination of both (HA/beta-TCP) were investigated as materials for three-dimensional printing process to create layer-by-layer structures for use as bone regeneration scaffolds. Different calcium-phosphate phases will result in different degrees of in vivo dissolution and/or cell-mediated resorption. There has been a growing interest in BCP because it has been shown that this material improves the formation of new bone inside the implanted scaffold. The literature indicates that the faster dissolution rate of ?-TCP would be greatly responsible of this enhancement. However, in vitro tests indicate that fast dissolution can decrease the mechanical strength of BCP scaffolds. Furthermore, studies reported that HA has higher mechanical strength and lower degradation rate than beta-TCP. Therefore, the HA/beta-TCP ratio is a key parameter controlling the performance of the scaffold for bone repair applications, since it determines degradation rate

  5. Pulsed electrodeposition for the synthesis of strontium-substituted calcium phosphate coatings with improved dissolution properties

    Energy Technology Data Exchange (ETDEWEB)

    Drevet, Richard, E-mail: richard.drevet@univ-reims.fr; Benhayoune, Hicham

    2013-10-15

    Strontium-substituted calcium phosphate coatings are synthesized by pulsed electrodeposition on titanium alloy (Ti6Al4V) substrates. Experimental conditions of the process are optimized in order to obtain a coating with a 5% atomic substitution of calcium by strontium which corresponds to the best observations on the osteoblast cells activity and on the osteoclast cells proliferation. The physical and chemical characterizations of the obtained coating are carried out by scanning electron microscopy associated to energy dispersive X-ray spectroscopy (EDXS) for X-ray microanalysis and the structural characterization of the coating is carried out by X-ray diffraction. The in vitro dissolution/precipitation properties of the coated substrates are investigated by immersion into Dulbecco's Modified Eagle Medium (DMEM) from 1 h to 14 days. The calcium, phosphorus and strontium concentrations variations in the biological liquid are assessed by Induced Coupled Plasma - Atomic Emission Spectroscopy for each immersion time. The results show that under specific experimental conditions, the electrodeposition process is suitable to synthesize strontium-substituted calcium phosphate coatings. Moreover, the addition of hydrogen peroxide (H{sub 2}O{sub 2}) into the electrolytic solution used in the process allows us to observe a control of the strontium release during the immersion of the prosthetic materials into DMEM. - Highlights: • Strontium-substituted calcium phosphate coatings are successfully electrodeposited. • The strontium is homogeneously distributed in the synthesized prosthetic coating. • This divalent cation modifies the calcium phosphate structure. • H{sub 2}O{sub 2} addition in the electrolyte allows to control the coating's stoichiometry. • This implies a control of the strontium release in the physiological environment.

  6. Long chain microRNA conjugates in calcium phosphate nanoparticles for efficient formulation and delivery.

    Science.gov (United States)

    Jung, Hyosook; Kim, Seung An; Yang, Yong Geun; Yoo, Hyundong; Lim, Soo-Jeong; Mok, Hyejung

    2015-01-01

    A long chain microRNA-34a conjugate (lc-miRNA) was prepared by chemical crosslinking in order to improve entrapment efficiency into calcium phosphate nanoparticles (CaPs) and intracellular delivery. Thiol-modified miRNA at both terminal ends was chemically conjugated using crosslinkers to form lc-miRNA which was encapsulated within CaPs by a conventional co-precipitation method. Encapsulation efficiencies, physicochemical properties, and in vitro intracellular delivery efficiencies of the prepared linear polyethyleneimine (LPEI)-coated CaPs (LPEI-CaP) containing common miRNA and lc-miRNA were comparatively evaluated. The prepared lc-miRNA exhibited noticeably enhanced encapsulation efficiency during the CaP formulation process when compared to common miRNA. LPEI-CaP/lc-miRNAs consisted of nano-sized particles with great homogeneity and were observed to be successfully delivered into PC-3 cells. Fabricated LPEI-CaPs with duplex form of lc-miRNA (lc-miRNA-d) suppressed cancer cell proliferation as well as migration much more efficiently than those with duplex form of miRNA (miRNA-d). In addition, LPEI-CaP/lc-miRNA-d conferred negligible cytotoxicity on PC-3 cells. Chemical crosslinking of therapeutic miRNAs via a reducible linkage may allow more efficient encapsulation within CaPs as well as homogeneous particle formulation due to a higher spatial charge density than common miRNAs. The well-formulated LPEI-CaPs with lc-miRNA-d have the potential to provide superior miRNA transfection efficiency and inhibition of cancer proliferation.

  7. In vitro elution of vancomycin from biodegradable osteoconductive calcium phosphate-polycaprolactone composite beads for treatment of osteomyelitis.

    Science.gov (United States)

    Makarov, C; Cohen, V; Raz-Pasteur, A; Gotman, I

    2014-10-01

    In this work, osteoconductive composite materials comprising a large volume fraction of a bioresorbable calcium phosphate ceramic (CaP) and a smaller amount of a polycaprolactone polymer (PCL) were studied as a degradable antibiotic carrier material for treatment of osteomyelitis. Beads loaded with 1 and 4wt.% vancomycin were prepared by admixing dissolved drug to an in situ synthesized dicalcium phosphate (DCP)-PCL or solution-mixed beta-tricalcium phosphate (βTCP)-PCL composite powder followed by high pressure consolidation of the blend at room temperature. Vancomycin release was measured in phosphate-buffered saline (PBS) at 37°C. All the beads gradually released the drug over the period of 4-11weeks, depending on the composite matrix homogeneity and porosity. Mathematical modeling using the Peppas equation showed that vancomycin elution was diffusion controlled. The stability of the antibiotic after high pressure application at room temperature was demonstrated by high-performance liquid chromatography-mass spectrometry (HPLC-MS) studies and MIC testing. The preservation of the structure and activity of vancomycin during the processing of composite beads and its sustained in vitro release profile suggest that high pressure consolidated CaP-PCL beads may be useful in the treatment of chronic bone infections as resorbable delivery vehicles of vancomycin and even of thermally unstable drug substances.

  8. The Effect of Premixed Schedule on the Crystal Formation of Calcium Phosphate Cement-chitosan Composite with Added Tetracycline

    Institute of Scientific and Technical Information of China (English)

    Jing MAO; Yan LIU; Bin ZHOU; Liyun YAO

    2008-01-01

    In this study, calcium phosphate cements (CPC) were prepared by mixing cement powders of tetracalcium phosphate (TTCP) with a cement liquid of phosphate acid saline solution. Tetracycline (TTC)-CPC, chitosan-CPC and chitosan-TTC-CPC were investigated with different premixed schedule. It was demonstrate that both TTC and chitosan worked on the phase transition and crystal characteristics. TTCP mixed with phosphate acid saline solution had similar features of Fourier transform-infrared spectrometry (FT-IR) no matter it was mixed with chitosan or TTC or both. TTC premixed with cement liquid or powder had significant different features of FT-IR and 876 cm-1seemed to be a special peak for TTC when TTC was premixed with cement liquid. This was also supported by XRD analysis, which showed that TTC premixed with cement liquid improved phase transition of TTCP to OCP. Chitosan, as organic additive, regulates the regular crystal formation and inhibits the phase transition of TTCP to OCP, except when it is mingled with cement liquid premixed with TTC in field scanning electron microscope. It was concluded that the premixed schedule influences the crystal formation and phase transition, which may be associated with its biocompatibility and bioactivities in vivo.

  9. Preparation and biological efficacy of haddock bone calcium tablets

    Science.gov (United States)

    Huo, Jiancong; Deng, Shanggui; Xie, Chao; Tong, Guozhong

    2010-03-01

    To investigate the possible use of waste products obtained after processing haddock, the present study prepared haddock bone calcium powder by NaOH and ethanol soaking (alkalinealcohol method) and prepared haddock bone calcium tablets using the powder in combination with appropriate excipients. The biological efficacy of the haddock bone calcium tablets was investigated using Wistar rats as an experiment model. Results show that the optimal parameters for the alkalinealcohol method are: NaOH concentration 1 mol/L, immersion time 30 h; ethanol concentration 60%, immersion time 15 h. A mixture of 2% polyvinylpyrrolidone in ethanol was used as an excipient at a ratio of 1:2 to full-cream milk powder, without the use of a disintegrating agent. This process provided satisfactory tablets in terms of rigidity and taste. Animal studies showed that the haddock bone calcium tablets at a dose of 2 g·kg-1·d-1 or 5g·kg-1·d-1 significantly increased blood calcium and phosphorus levels and bone calcium content in rats. Therefore, these tablets could be used for calcium supplementation and prevent osteoporosis. Although the reasons of high absorption in the rats fed with haddock bone calcium tablets are unclear, it is suggested that there are some factors, such as treatment with method of alkaline-alcohol or the added milk, may play positive roles in increasing absorption ratio.

  10. Grafting cyclodextrins to calcium phosphate ceramics for biomedical applications

    DEFF Research Database (Denmark)

    Jacobsen, P.A.L.; Nielsen, J.L.; Juhl, M.V.

    2012-01-01

    The grafting of hydroxyapatite/beta-tricalcium phosphate with β-cyclodextrin was achieved using a two step reaction with (3-glycidyloxypropyl)trimethoxysilane as a linker. Firstly, the silane group was brought to react with the hydroxyl groups at the surface of the hydroxyapatite/beta-tricalcium ....... The concentration of grafted β-cyclodextrin was found to be approximately 3.5 μmol per gram of material corresponding to an almost complete surface coverage, when assuming a closed hexagonal packed monolayer....

  11. Dynamic changes in calcium and phosphate plasma concentrations in the patients on peritoneal dialysis

    Directory of Open Access Journals (Sweden)

    Jovanović Nataša

    2006-01-01

    Full Text Available Background/Aim. The disturbances of active forms of vitamin D synthesis and disturbances in calcium and posphate metabolism develop early in chronic renal failure, when creatinine clearance is about 30 ml/min. Chronic hemodialysis and peritoneal dialysis only partially correct the biochemical environment of patients on chronic renal replacement therapy because of end-stage renal disease. These dialysis modalities can’t significantly affect the endocrine disturbances of chronic renal failure and they have minimal modulatory effect. The management of disturbed calcium (Ca and phosphate (P metabolism and the maintainance of Ca × P product below 4.4 mmol/l thanks to the use of dialysate solutions with the appropriate calcium concentration and the careful dosage of phosphate binders, calcium and active vitamin D metabolits, are extremely important for the prevention of renal osteodystrophy, secondary hyperparathyroidism as well as low-bone turnover disease. The aim of the study was to analyze the plasma levels of calcium, phosphate, albumin, alkaline phosphatase and parathormon (PTH in 58 patients who were treated with continuous ambulatory peritoneal dialysis (CAPD from March to August 2003. The use of phosphate binders and the substitution with active vitamin D metabolits were also analyzed. Methods. We examined 58 patients, 30 males and 28 female, mean-age 52 years (range, 26-78 years, affected by end-stage renal disease of the different leading cause. The average time on peritoneal dialysis program was 20 months (2-66 months. Most of the patients were treated by CAPD, while only few of them performed automatic, cyclic or intermittent peritoneal dialysis. Most of the patients used a dialysate with 1.75 mmol/l calcium concentration. Results. The study showed that our patients on chronic CAPD program during several months had normal calcemia, phosphatemia and the level of alkaline phosphatase, and that they had Ca × P product in the recommended

  12. Fluoride-containing nanoporous calcium-silicate MTA cements for endodontics and oral surgery: early fluorapatite formation in a phosphate-containing solution.

    Science.gov (United States)

    Gandolfi, M G; Taddei, P; Siboni, F; Modena, E; Ginebra, M P; Prati, C

    2011-10-01

    To test the chemical-physical properties and apatite-forming ability of experimental fluoride-doped calcium silicate cements designed to create novel bioactive materials for use in endodontics and oral surgery. A thermally treated calcium silicate cement (wTC) containing CaCl(2) 5%wt was modified by adding NaF 1%wt (FTC) or 10%wt (F10TC). Cements were analysed by environmental scanning electron microscopy with energy-dispersive X-ray analysis, IR and micro-Raman spectroscopy in wet conditions immediately after preparation or after ageing in a phosphate-containing solution (Dulbecco's phosphate-buffered saline). Calcium and fluoride release and pH of the storage solution were measured. The results obtained were analysed statistically (Tukey's HSD test and two-way anova). The formation of calcium phosphate precipitates (spherulites) was observed on the surface of 24 h-aged cements and the formation of a thick bone-like B-type carbonated apatite layer (biocoating) on 28 day-aged cements. The rate of apatite formation was FTC>F10TC>wTC. Fluorapatite was detected on FTC and F10TC after 1 day of ageing, with a higher fluoride content on F10TC. All the cements released calcium ions. At 5 and 24 h, the wTC had the significantly highest calcium release (Pfluoride release at all times (Pfluoride accelerated apatite formation on calcium silicate cements. Fluoride-doped calcium silicate cements had higher bioactivity and earlier formation of fluorapatite. Sodium fluoride may be introduced in the formulation of mineral trioxide aggregate cements to enhance their biological behaviour. F-doped calcium silicate cements are promising bone cements for clinical endodontic use. © 2011 International Endodontic Journal.

  13. Effect of silica on porosity, strength, and toughness of pressureless sintered calcium phosphate-zirconia bioceramics.

    Science.gov (United States)

    Schumacher, Thomas C; Treccani, Laura; Rezwan, Kurosch

    2015-08-12

    The preparation of dense, high-strength calcium phosphate-zirconia (CaP-ZrO2) composed bioceramics is realized via versatile pressureless sintering by adding silica nanoparticles. Two different weight ratios of HAp:ZrO2, 9:1 and 1:1, are used with varying silica contents from 5 to 20 wt%. After sintering at 1200 °C, the phase composition, microstructure, porosity, biaxial bending strength, and fracture toughness as well as SBF in vitro bioactivity are characterized. We show that the addition of silica altered the crystal phase composition, inhibiting the formation of non-favourable cubic ZrO2. Furthermore, SiO2 addition leads to an increase of the biaxial bending strength, and the fracture toughness of CaP-ZrO2-containing materials. With the addition of 20 wt% silica we find the highest characteristic strength (268 MPa) and toughness (2.3   ±   0.1 MPam(0.5)) at  <1% porosity. Both mechanical properties are 2 times higher than those of pure hydroxyapatite. At the same time we observe for the very same composition similar bioactivity to that of pure hydroxyapatite.

  14. Influence of water content on hardening and handling of a premixed calcium phosphate cement.

    Science.gov (United States)

    Engstrand, Johanna; Aberg, Jonas; Engqvist, Håkan

    2013-01-01

    Handling of calcium phosphate cements is difficult, where problems often arise during mixing, transferring to syringes, and subsequent injection. Via the use of premixed cements the risk of handling complications is reduced. However, for premixed cements to work in a clinical situation the setting time needs to be improved. The objective of this study is to investigate the influence of the addition of water on the properties of premixed cement. Monetite-forming premixed cements with small amounts of added water (less than 6.8 wt.%) were prepared and the influence on injectability, working time, setting time and mechanical strength was evaluated. The results showed that the addition of small amounts of water had significant influence on the properties of the premixed cement. With the addition of just 1.7 wt.% water, the force needed to extrude the cement from a syringe was reduced from 107 (±15) N to 39 (±9) N, the compression strength was almost doubled, and the setting time decreased from 29 (±4) min to 19 (±2) min, while the working time remained 5 to 6h. This study demonstrates the importance of controlling the water content in premixed cement pastes and how water can be used to improve the properties of premixed cements.

  15. Effect of calcium phosphate addition on sintering of El-Oued sand quartz raw materials

    Directory of Open Access Journals (Sweden)

    L. Foughali

    2014-12-01

    Full Text Available This work addresses the development of an eventual low cost ceramic insulating or microfiltration membrane supports from inexpensive raw materials such Eloued quartz sand (EQS and calcium phosphate (CP using uniaxially dry compaction method. The prepared samples were sintered at different temperatures ranging between 1200 and 1550 ºC. Subsequently, the effects of sintering temperature and amount of CP on samples proprieties were investigated. It is observed that X-ray diffracion measurements confirmed that EQS was transformed into cristobalite and tridymite phases when both sintering temperature and holding time were increased. This transformation is favored with increasing amount of CP, it is observed also formation of CaSiO3 and Ca(Fe(AlPO4. The SEM images of the samples sintered at different temperatures illustrate that silica grains, CP grains, intergranular phase contents (Si, Ca, P, and O and an important open porosity depend on the sintering temperature. The porosity ratio changes in the range between 37% and 34% according to sintering temperature and to CP content; these values are in good agreement with SEM images. The thermal expansion behavior shows a weak expansion in the range of temperature between 600 and 1000 ºC which is situated between 1.27% and 1.33% (variation of 0.05% at 400 ºC.

  16. Solution combustion synthesis of calcium phosphate particles for controlled release of bovine serum albumin

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Junfeng, E-mail: daidai02304@163.com [School of Chemistry and Materials Engineering, Changshu Institute of Technology, Changshu (China); Jiangsu Laboratory of Advanced Functional Materials, Changshu Institute of Technology, Changshu (China); Zhao, Junjie; Qian, Yu; Zhang, Xiali; Zhou, Feifei; Zhang, Hong [School of Chemistry and Materials Engineering, Changshu Institute of Technology, Changshu (China); Lu, Hongbin [National Laboratory of Solid State Microstructures, College of Engineering and Applied Sciences, Nanjing University, Nanjing (China); Chen, JianHua; Wang, XuHong [School of Chemistry and Materials Engineering, Changshu Institute of Technology, Changshu (China); Jiangsu Laboratory of Advanced Functional Materials, Changshu Institute of Technology, Changshu (China); Yu, Wencong [School of Chemistry and Materials Engineering, Changshu Institute of Technology, Changshu (China)

    2015-05-01

    Four different phase compositions of calcium phosphate (CaP) particles were prepared via a solution combustion method. X-ray diffraction (XRD) and Rietveld analysis results revealed that the variations in the nominal Ca/P (molar) ratios were found to provide a favorable control in the different proportions of CaP materials. Bovine serum albumin (BSA) was used as a model protein to study the loading and release behavior. The release profile indicated that the BSA release rates depended on the phase compositions of the CaP particles, and showed an order of TCP-BSA > BCP-1-BSA > BCP-2-BSA > HA-BSA. The results suggested that the BSA protein release rate can be controlled by varying the phase compositions of CaP carriers. Moreover, the release process involved two stages: firstly surface diffusion via ion exchange and secondly intraparticle diffusion. - Highlights: • Solution combustion method was an efficient way to produced CaP powders. • Ca/P (molar) ratios provided a favorable control in the different proportions of phase composition. • BSA release rate varied depending on the phase composition of the CaP particles. • Two kinetic models were chosen to simulate the release kinetics of the drugs from CaP carriers.

  17. Cross-linked chitosan improves the mechanical properties of calcium phosphate-chitosan cement.

    Science.gov (United States)

    Aryaei, Ashkan; Liu, Jason; Jayatissa, Ahalapitiya H; Jayasuriya, A Champa

    2015-09-01

    Calcium phosphate (CaP) cements are highly applicable and valuable materials for filling bone defects by minimally invasive procedures. The chitosan (CS) biopolymer is also considered as one of the promising biomaterial candidates in bone tissue engineering. In the present study, some key features of CaP-CS were significantly improved by developing a novel CaP-CS composite. For this purpose, CS was the first cross-linked with tripolyphosphate (TPP) and then mixed with CaP matrix. A group of CaP-CS samples without cross-linking was also prepared. Samples were fabricated and tested based on the known standards. Additionally, the effect of different powder (P) to liquid (L) ratios was also investigated. Both cross-linked and uncross-linked CaP-CS samples showed excellent washout resistance. The most significant effects were observed on Young's modulus and compressive strength in wet condition as well as surface hardness. In dry conditions, the Young's modulus of cross-linked samples was slightly improved. Based on the presented results, cross-linking does not have a significant effect on porosity. As expected, by increasing the P/L ratio of a sample, ductility and injectability were decreased. However, in the most cases, mechanical properties were enhanced. The results have shown that cross-linking can improve the mechanical properties of CaP-CS and hence it can be used for bone tissue engineering applications.

  18. Biological influence of Ca/P ratio on calcium phosphate coatings by sol-gel processing.

    Science.gov (United States)

    Catauro, M; Papale, F; Sapio, L; Naviglio, S

    2016-08-01

    The objective of this work has been to develop low temperature sol-gel glass coatings to modify the substrate surface and to evaluate their bioactivity and biocompatibility. Glasses, based on SiO2·CaO·P2O5, were synthesized by the sol-gel technique using tetraethyl orthosilicate, calcium nitrate tetrahydrate and triethyl phosphate as precursors of SiO2, CaO and P2O5, respectively. Those materials, still in the sol phase, have been used to coat substrates by means of the dip-coating technique. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) has been used for characterize coatings and a microstructural analysis has been obtained using scanning electron microscopy (SEM). The potential applications of the coatings in the biomedical field were evaluated by bioactivity and biocompatibility tests. The coated substrate was immersed in simulated body fluid (SBF) for 21days and the hydroxyapatite deposition on its surface was subsequently evaluated via SEM-EDXS analysis, as an index of bone-bonding capability. In order to study the cell behavior and response to our silica based materials, prepared via the sol-gel method, with various Ca/P ratio and coating substrate, we have used the human osteoblast-like U2OS cell line.

  19. Bone Tissue Engineering by Using Calcium Phosphate Glass Scaffolds and the Avidin-Biotin Binding System.

    Science.gov (United States)

    Kim, Min-Chul; Hong, Min-Ho; Lee, Byung-Hyun; Choi, Heon-Jin; Ko, Yeong-Mu; Lee, Yong-Keun

    2015-12-01

    Highly porous and interconnected scaffolds were fabricated using calcium phosphate glass (CPG) for bone tissue engineering. An avidin-biotin binding system was used to improve osteoblast-like cell adhesion to the scaffold. The scaffolds had open macro- and micro-scale pores, and continuous struts without cracks or defects. Scaffolds prepared using a mixture (amorphous and crystalline CPG) were stronger than amorphous group and crystalline group. Cell adhesion assays showed that more cells adhered, with increasing cell seeding efficiency to the avidin-adsorbed scaffolds, and that cell attachment to the highly porous scaffolds significantly differed between avidin-adsorbed scaffolds and other scaffolds. Proliferation was also significantly higher for avidin-adsorbed scaffolds. Osteoblastic differentiation of MG-63 cells was observed at 3 days, and MG-63 cells in direct contact with avidin-adsorbed scaffolds were positive for type I collagen, osteopontin, and alkaline phosphatase gene expression. Osteocalcin expression was observed in the avidin-adsorbed scaffolds at 7 days, indicating that cell differentiation in avidin-adsorbed scaffolds occurred faster than the other scaffolds. Thus, these CPG scaffolds have excellent biological properties suitable for use in bone tissue engineering.

  20. Incorporation of biodegradable electrospun fibers into calcium phosphate cement for bone regeneration.

    Science.gov (United States)

    Zuo, Yi; Yang, Fang; Wolke, Joop G C; Li, Yubao; Jansen, John A

    2010-04-01

    Inherent brittleness and slow degradation are the major drawbacks for the use of calcium phosphate cements (CPCs). To address these issues, biodegradable ultrafine fibers were incorporated into the CPC in this study. Four types of fibers made of poly(epsilon-caprolactone) (PCL) (PCL12: 1.1 microm, PCL15: 1.4 microm, PCL18: 1.9 microm) and poly(l-lactic acid) (PLLA4: 1.4 microm) were prepared by electrospinning using a special water pool technique, then mixed with the CPC at fiber weight fractions of 1%, 3%, 5% and 7%. After incubation of the composites in simulated body fluid for 7 days, they were characterized by a gravimetric measurement for porosity evaluation, a three-point bending test for mechanical properties, microcomputer topography and scanning electron microscopy for morphological observation. The results indicated that the incorporation of ultrafine fibers increases the fracture resistance and porosity of CPCs. The toughness of the composites increased with the fiber fraction but was not affected by the fiber diameter. It was found that the incorporated fibers formed a channel-like porous structure in the CPCs. After degradation of the fibers, the created space and high porosity of the composite cement provides inter-connective channels for bone tissue in growth and facilitates cement resorption. Therefore, we concluded that this electrospun fiber-CPC composite may be beneficial to be used as bone fillers.

  1. Characterization and properties of novel gallium-doped calcium phosphate ceramics.

    Science.gov (United States)

    Mellier, Charlotte; Fayon, Franck; Schnitzler, Verena; Deniard, Philippe; Allix, Mathieu; Quillard, Sophie; Massiot, Dominique; Bouler, Jean-Michel; Bujoli, Bruno; Janvier, Pascal

    2011-09-05

    Addition of a gallium (Ga) precursor in the typical reaction protocols used for the preparation of β-tricalcium phosphate (β-TCP) led to novel Ga-doped β-TCP ceramics with rhombohedral structures (R3c space group). From the refinement of their X-ray diffraction patterns, it was found that the incorporation of Ga in the β-TCP network occurs by substitution of one of the five calcium (Ca) sites, while occupation of another Ca site decreases in inverse proportion to the Ga content in the structure. The Ga local environment and the modification of the phosphorus environments due to the Ga/Ca substitution in Ga-doped β-TCP compounds are probed using (31)P and (71)Ga magic-angle spinning NMR. A decrease of the unit cell volume is observed with increasing Ga content, together with improved mechanical properties. Indeed, the compressive strength of these new bioceramics is enhanced in direct proportion of the Ga content, up to a 2.6-fold increase as compared to pure β-TCP.

  2. Antibacterial activity evaluation of bioactive glass and biphasic calcium phosphate nanopowders mixtures

    Science.gov (United States)

    Nazemi, Zahra; Mehdikhani-Nahrkhalaji, Mehdi; Haghbin-Nazarpak, Masoumeh; Staji, Hamid; Kalani, Mohammad Mehdi

    2016-12-01

    The aim of this work was to evaluate the antibacterial activity of bioactive glass (BG) and biphasic calcium phosphate (BCP) nanopowders mixtures for the first time. 37S BG and BCP (50% HA-50% β-TCP) nanopowders were prepared via sol-gel technique. Characterization techniques such as X-ray diffraction, scanning electron microscopy, transition electron microscopy, and X-ray fluorescent. The antibacterial activity was studied using Escherichia coli and Salmonella typhi as gram-negative, and Staphylococcus aureus as gram-positive bacteria. The antibacterial effect of BG, BCP nanopowders, and their mixtures was evaluated at different concentrations. The 37S BG nanopowders showed minimum bactericidal concentration at 25 mg/ml. At broth concentrations below 300 mg/ml, BCP showed no antibacterial activity. BCP and BG nanopowders mixture (M2) with 60/40 ratio of BCP/BG showed noticeable antibacterial effect. It was concluded that BCP and 37S BG nanopowders mixture could be used as a good candidate for dental and orthopedic applications.

  3. White light emission of dysprosium doped lanthanum calcium phosphate oxide and oxyfluoride glasses

    Science.gov (United States)

    Luewarasirikul, N.; Kim, H. J.; Meejitpaisan, P.; Kaewkhao, J.

    2017-04-01

    Lanthanum calcium phosphate oxide and oxyfluoride glasses doped with dysprosium oxide were prepared by melt-quenching technique with chemical composition 20La2O3:10CaO:69P2O5:1Dy2O3 and 20La2O3:10CaF2:69P2O5:1Dy2O3. The physical, optical and luminescence properties of the glass samples were studied to evaluate their potential to using as luminescence materials for solid-state lighting applications. The density, molar volume and refractive index of the glass samples were carried out. The optical and luminescence properties were studied by investigating absorption, excitation, and emission spectra of the glass samples. The absorption spectra were investigated in the UV-Vis-NIR region from 300 to 2000 nm. The excitation spectra observed under 574 nm emission wavelength showed the highest peak centered at 349 nm (6H15/2 → 6P7/2). The emission spectra, excited with 349 nm excitation wavelength showed two major peaks corresponding to 482 nm blue emission (4F9/2 → 6H15/2) and 574 nm yellow emission (4F9/2 → 6H13/2). The experimental lifetime were found to be 0.539 and 0.540 for oxide and oxyfluoride glass sample, respectively. The x,y color coordinates under 349 nm excitation wavelength were (0.38, 0.43) for both glass samples, that be plotted in white region of CIE 1931 chromaticity diagram. The CCT values obtained from the glass samples are 4204 K for oxide glass and 4228 K for oxyfluoride glass corresponding to the commercial cool white light (3100-4500 K). Judd-Ofelt theory had also been employed to obtain the J-O parameters (Ω2, Ω4 and Ω6), oscillator strength, radiative transition possibility, stimulated emission cross section and branching ratio. The Ω2 > Ω4 > Ω6 trend of J-O parameters of both glass samples may indicate the good quality of a glass host for using as optical device application. Temperature dependence of emission spectra was studied from 300 K to 10 K and found that the intensity of the emission peak was found to be increased with

  4. In vitro aging of a calcium phosphate cement.

    Science.gov (United States)

    Bohner, M; Merkle, H P; Lemaître, J

    2000-03-01

    Cement samples made of beta-tricalcium phoshate (beta-TCP), phosphoric acid (PA) and water mixtures were incubated in several aqueous solutions to determine their stability over time. The effects of the cement composition and the incubating temperature were investigated in more detail. The cement samples contained mostly dicalcium phosphate dihydrate (DCPD) and remnants of beta-TCP crystals. Depending on the initial cement composition, a certain amount of dicalcium phosphate (DCP) crystals were formed. The larger the initial PA concentration, the larger the DCP amount. After setting, the cement composition was stable for at least 16 days up to 60 degrees C. Above that temperature, the DCPD crystals decomposed into DCP crystals. The latter reaction provoked a decrease of the pH of the incubation solution, phenomenon expected for a cement sample containing an excess of PA. As the cement samples contained an excess of beta-TCP, it was postulated that beta-TCP crystals became so covered by DCP or DCPD crystals during setting that the setting reaction was stopped prematurely. The latter phenomenon gave a good explanation for the low pH values measured in the incubation solutions.

  5. Effect of Fluoride, Casein Phosphopeptide–Amorphous Calcium Phosphate and Casein Phosphopeptide–Amorphous Calcium Phosphate Fluoride on Enamel Surface Microhardness After Microabrasion: An In Vitro Study

    Directory of Open Access Journals (Sweden)

    Ghazaleh Ahmadi Zenouz

    2016-03-01

    Full Text Available Objectives: This study aimed to assess the effect of applying casein phosphopeptide–amorphous calcium phosphate (CPP-ACP paste, casein phosphopeptide–amorphous calcium phosphate fluoride (CPP-ACPF paste and sodium fluoride gel on surface microhardness of enamel after microabrasion.Materials and Methods: Thirty freshly extracted human premolars were selected. All samples were subjected to hardness indentations made with the Vickers hardness machine and the average value was recorded as the initial surface microhardness. The specimens were then randomly divided into three groups (n=10 of CPP-ACPF, fluoride and CPP-ACP. The teeth were micro-abraded with Opalustre. Microhardness test was performed to assess the post-abrasion hardness. Three remineralization modalities were performed on samples of each group. The enamel surface microhardness measurements were performed. To compare the difference between groups, the rehardening and softening values were defined. One-way ANOVA and Tukey’s post hoc test at a significance level of 5% were used for statistical analysis.Results: The mean microhardness value (MMV had a significant decrease after microabrasion from baseline. The MMV had a significant increase after remineralization in all groups. The MMV of CPP-ACPF group was significantly more than that of fluoride group (P=0.027. The rehardening value of fluoride group was significantly more than that of other groups (P<0.001.Conclusion: All the remineralizing agents were effective for rehardening the enamel after microabrasion. The CPP-ACP and CPP-ACPF pastes are effective, but to a lesser extent than neutral sodium fluoride gel in remineralizing enamel surface. Incorporation of fluoride to CPP-ACP formulation does not provide any additional remineralizing potential.Keywords: Casein phosphopeptide-amorphous calcium phosphate nanocomplex; Enamel Microabrasion; Hardness; Sodium Fluoride

  6. Effects of Nano-biphasic Calcium Phosphate Composite on Bioactivity and Osteoblast Cell Behavior in Tissue Engineering Applications.

    Science.gov (United States)

    Ebrahimian-Hosseinabadi, Mehdi; Etemadifar, Mohammadreza; Ashrafizadeh, Fakhredin

    2016-01-01

    In this paper, preparation, bioactivity, and osteoblast cell behavior of cortical bone derived nano-biphasic calcium phosphate (nano-BCP) are presented. The calcined bovine bone samples with the addition of di-ammonium hydrogen phosphate were heated at 700°C for 100 min, and thus nano-BCP with the composition of 63/37 hydroxyapatite (HA)/β-tricalcium phosphate (β-TCP) was produced. Scanning electron microscopy (SEM) images, energy dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD) analysis of immersed samples in simulated body fluid (SBF) solution showed that a uniform layer was formed on the surface after 7 days with the chemical composition of HA. The results indicated that the nano-BCP sample developed excellent bioactivity after 28 days. The nano-BCP samples showed better cell proliferation compared to pure HA samples. After 7 days in cell culture, the prepared nano-BCP (HA/β-TCP) exhibited the maximum proliferation of the MG-63 osteoblast cells.

  7. Magnesium substitution in the structure of orthopedic nanoparticles: A comparison between amorphous magnesium phosphates, calcium magnesium phosphates, and hydroxyapatites

    Energy Technology Data Exchange (ETDEWEB)

    Nabiyouni, Maryam, E-mail: maryam.nabiyouni@rockets.utoledo.edu [Department of Bioengineering, University of Toledo, Toledo, OH (United States); Ren, Yufu [Department of Mechanical, Industrial and Manufacturing Engineering, University of Toledo, Toledo, OH (United States); Bhaduri, Sarit B. [Department of Mechanical, Industrial and Manufacturing Engineering, University of Toledo, Toledo, OH (United States); Department of Surgery (Dentistry), University of Toledo, Toledo, OH (United States)

    2015-07-01

    As biocompatible materials, magnesium phosphates have received a lot of attention for orthopedic applications. During the last decade multiple studies have shown advantages for magnesium phosphate such as lack of cytotoxicity, biocompatibility, strong mechanical properties, and high biodegradability. The present study investigates the role of Mg{sup +2} and Ca{sup +2} ions in the structure of magnesium phosphate and calcium phosphate nanoparticles. To directly compare the effect of Mg{sup +2} and Ca{sup +2} ions on structure of nanoparticles and their biological behavior, three groups of nanoparticles including amorphous magnesium phosphates (AMPs) which release Mg{sup +2}, calcium magnesium phosphates (CMPs) which release Mg{sup +2} and Ca{sup +2}, and hydroxyapatites (HAs) which release Ca{sup +2} were studied. SEM, TEM, XRD, and FTIR were used to evaluate the morphology, crystallinity, and chemical properties of the particles. AMP particles were homogeneous nanospheres, whereas CMPs were combinations of heterogeneous nanorods and nanospheres, and HAs which contained heterogeneous nanosphere particles. Cell compatibility was monitored in all groups to determine the cytotoxicity effect of particles on studied MC3T3-E1 preosteoblasts. AMPs showed significantly higher attachment rate than the HAs after 1 day and both AMPs and CMPs showed significantly higher proliferation rate when compared to HAs after 7 days. Gene expression level of osteoblastic markers ALP, COL I, OCN, OPN, RUNX2 were monitored and they were normalized to GAPDH housekeeping gene. Beta actin expression level was monitored as the second housekeeping gene to confirm the accuracy of results. In general, AMPs and CMPs showed higher expression level of osteoblastic genes after 7 days which can further confirm the stimulating role of Mg{sup +}2 and Ca{sup +2} ions in increasing the proliferation rate, differentiation, and mineralization of MC3T3-E1 preosteoblasts. - Highlights: • Role of Mg{sup 2

  8. Calcium Carbonate versus Sevelamer Hydrochloride as Phosphate Binders after Long-Term Disease Progression in 5/6 Nephrectomized Rats

    Directory of Open Access Journals (Sweden)

    Suvi Törmänen

    2014-01-01

    Full Text Available Our aim was to compare the effects of calcium carbonate and sevelamer-HCl treatments on calcium-phosphate metabolism and renal function in 5/6 nephrectomized (NX rats so that long-term disease progression preceded the treatment. After 15-week progression, calcium carbonate (3.0%, sevelamer-HCl (3.0%, or control diets (0.3% calcium were given for 9 weeks. Subtotal nephrectomy reduced creatinine clearance (−40%, plasma calcidiol (−25%, and calcitriol (−70% and increased phosphate (+37%, parathyroid hormone (PTH (11-fold, and fibroblast growth factor-23 (FGF-23 (4-fold. In NX rats, calcium carbonate diet increased plasma (+20% and urinary calcium (6-fold, reduced plasma phosphate (−50% and calcidiol (−30%, decreased creatinine clearance (−35% and FGF 23 (−85%, and suppressed PTH without influencing blood pH. In NX rats, sevelamer-HCl increased urinary calcium (4-fold and decreased creatinine clearance (−45%, PTH (−75%, blood pH (by 0.20 units, plasma calcidiol (−40%, and calcitriol (−65%. Plasma phosphate and FGF-23 were unchanged. In conclusion, when initiated after long-term progression of experimental renal insufficiency, calcium carbonate diet reduced plasma phosphate and FGF-23 while sevelamer-HCl did not. The former induced hypercalcemia, the latter induced acidosis, while both treatments reduced vitamin D metabolites and deteriorated renal function. Thus, delayed initiation influences the effects of these phosphate binders in remnant kidney rats.

  9. Ectopic osteoid and bone formation by three calcium-phosphate ceramics in rats, rabbits and dogs.

    Directory of Open Access Journals (Sweden)

    Liao Wang

    Full Text Available Calcium phosphate ceramics with specific physicochemical properties have been shown to induce de novo bone formation upon ectopic implantation in a number of animal models. In this study we explored the influence of physicochemical properties as well as the animal species on material-induced ectopic bone formation. Three bioceramics were used for the study: phase-pure hydroxyapatite (HA sintered at 1200°C and two biphasic calcium phosphate (BCP ceramics, consisting of 60 wt.% HA and 40 wt.% TCP (β-Tricalcium phosphate, sintered at either 1100°C or 1200°C. 108 samples of each ceramic were intramuscularly implanted in dogs, rabbits, and rats for 6, 12, and 24 weeks respectively. Histological and histomorphometrical analyses illustrated that ectopic bone and/or osteoid tissue formation was most pronounced in BCP sintered at 1100°C and most limited in HA, independent of the animal model. Concerning the effect of animal species, ectopic bone formation reproducibly occurred in dogs, while in rabbits and rats, new tissue formation was mainly limited to osteoid. The results of this study confirmed that the incidence and the extent of material-induced bone formation are related to both the physicochemical properties of calcium phosphate ceramics and the animal model.

  10. ATR-FTIR measurements of albumin and fibrinogen adsorption: Inert versus calcium phosphate ceramics.

    Science.gov (United States)

    Boix, Marcel; Eslava, Salvador; Costa Machado, Gil; Gosselin, Emmanuel; Ni, Na; Saiz, Eduardo; De Coninck, Joël

    2015-11-01

    Arthritis, bone fracture, bone tumors and other musculoskeletal diseases affect millions of people across the world. Nowadays, inert and bioactive ceramics are used as bone substitutes or for bone regeneration. Their bioactivity is very much dictated by the way proteins adsorb on their surface. In this work, we compared the adsorption of albumin and fibrinogen on inert and calcium phosphates ceramics (CaPs) using attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR) to follow in situ protein adsorption on these materials. To this effect, we developed a sol-gel technique to control the surface chemistry of an ATR-FTIR detector. Hydroxyapatite adsorbed more albumin and β-tricalcium phosphate adsorbed more fibrinogen. Biphasic calcium phosphate presented the lowest adsorption among CaP for both proteins, illustrating the effect of surface heterogeneities. Inert ceramics adsorbed a lower amount of both proteins compared with bioactive ceramics. A significant change was observed in the conformation of the adsorbed protein versus the surface chemistry. Hydroxyapatite produced a larger loss of α-helix structure on albumin and biphasic calcium phosphate reduced β-sheet percentage on fibrinogen. Inert ceramics produced large α-helix loss on albumin and presented weak interaction with fibrinogen. Zirconia did not adsorb albumin and titanium dioxide promoted huge denaturalization of fibrinogen.

  11. Synthesis and characterization of calcium phosphate/collagen biocomposites doped with Zn{sup 2+}

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Maria Helena [Department of Dentistry, Federal University of Vales do Jequitinhonha e Mucuri-UFVJM, mailbox 38, Zip:39100-000, Diamantina, MG (Brazil)], E-mail: mariahelena.santos@gmail.com; Dias Heneine, Luis Guilherme [Department of Health Science, Ezequiel Dias Foundation, Belo Horizonte, MG (Brazil); Sander Mansur, Herman [Department of Metallurgical and Materials Engineering, Federal University of Minas Gerais, Belo Horizonte, MG (Brazil)

    2008-05-01

    Composites were developed using calcium phosphate (CaP)/collagen (COL) doped with Zn{sup +2} to attempt the materials association with adequate properties for biological applications in the recovery of the bone tissue by trauma or pathogenies. Hydroxyapatite (HAP) and hydroxyapatite-{beta}tricalcium phosphate (HAP{beta}TCP) were synthesized and doped with zinc nitrate. High purity grade type I collagen was extracted and purified from bovine pericardium. CaP doped and undoped with Zn{sup +2} were produced with COL and the composites were developed using a simple mixture process. All samples were characterized by Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR) and X-ray diffraction analysis (XRD. In addition, biocompatibility and cell viability were assessed by MTT assay (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-tetrazolium bromide) using osteoblast cell culture. The results have indicated that both morphological and structural features and chemical composition of the composites were very similar to their precursors, collagen and calcium phosphate components. Also, the biocomposites presented a homogeneous aspect with the calcium phosphate particles aggregated to the collagen fibers. The biological evaluation of the composites in vitro showed cellular viability, presenting proliferation of the osteoblasts compared to the control cells (P < 0.05). The composites showed appropriate physical and biological properties creating more biologically active scaffolds that may support bone growth. Therefore, the novel developed biocomposites have high potential to be used for rebuilding small lesions in bone tissue engineering.

  12. Structural characterization of anion-calcium-humate complexes in phosphate-based fertilizers.

    Science.gov (United States)

    Baigorri, Roberto; Urrutia, Oscar; Erro, Javier; Mandado, Marcos; Pérez-Juste, Ignacio; Garcia-Mina, José María

    2013-07-01

    Fertilizers based on phosphate-metal-humate complexes are a new family of compounds that represents a more sustainable and bioavailable phosphorus source. The characterization of this type of complex by using solid (31)P NMR in several fertilizers, based on single superphosphate (SSP) and triple superphosphate (TSP) matrices, yielded surprising and unexpected trends in the intensity and fine structure of the (31)P NMR peaks. Computational chemistry methods allowed the characterization of phosphate-calcium-humate complexes in both SSP and TSP matrices, but also predicted the formation of a stable sulfate-calcium-humate complex in the SSP fertilizers, which has not been described previously. The stability of this complex has been confirmed by using ultrafiltration techniques. Preference towards the humic substance for the sulfate-metal phase in SSP allowed the explanation of the opposing trends that were observed in the experimental (31)P NMR spectra of SSP and TSP samples. Additionally, computational chemistry has provided an assignment of the (31)P NMR signals to different phosphate ligands as well as valuable information about the relative strength of the phosphate-calcium interactions within the crystals.

  13. Development of a fully injectable calcium phosphate cement for orthopedic and dental applications

    Indian Academy of Sciences (India)

    Manoj Komath; H K Varma

    2003-06-01

    A study on the development of a fully injectable calcium phosphate cement for orthopedic and dental applications is presented. The paper describes its characteristic properties including results of bio- compatibility studies. A conventional two-component calcium phosphate cement formulation (having a powder part containing dry mixture of acidic and basic calcium phosphate particles and a liquid part containing phosphate solution) is modified with a biocompatible gelling agent, to induce flow properties and cohesion. The quantity of the gelling agent is optimized to get a viscous paste, which is smoothly injectable through an 18-gauge needle, with clinically relevant setting parameters. The new formulation has a setting time of 20 min and a compressive strength of 11 MPa. The X-ray diffraction, Fourier transform infrared spectrometry, and energy dispersive electron microprobe analyses showed the phase to be hydroxyapatite, the basic bone mineral. Scanning electron microscopy revealed a porous structure with particle sizes of a few micrometers. The cement did not show any appreciable dimensional or thermal change during setting. The injectability is estimated by extruding through needle and the cohesive property is assessed by water contact method. The cement passed the in vitro biocompatibility screening (cytotoxicity and haemolysis) tests.

  14. Mineralization of annexin-5-containing lipid-calcium-phosphate complexes: modulation by varying lipid composition and incubation with cartilage collagens.

    Science.gov (United States)

    Genge, Brian R; Wu, Licia N Y; Wuthier, Roy E

    2008-04-11

    Matrix vesicles (MVs) in the growth plate bind to cartilage collagens and initiate mineralization of the extracellular matrix. Native MVs have been shown to contain a nucleational core responsible for mineral formation that is comprised of Mg(2+)-containing amorphous calcium phosphate and lipid-calcium-phosphate complexes (CPLXs) and the lipid-dependent Ca(2+)-binding proteins, especially annexin-5 (Anx-5), which greatly enhances mineral formation. Incorporation of non-Ca(2+)-binding MV lipids impedes mineral formation by phosphatidylserine (PS)-CPLX. In this study, nucleators based on amorphous calcium phosphate (with or without Anx-5) were prepared with PS alone, PS + phosphatidylethanolamine (PE), or PS + PE and other MV lipids. These were incubated in synthetic cartilage lymph containing no collagen or containing type II or type X collagen. Dilution of PS with PE and other MV lipids progressively retarded nucleation. Incorporation of Anx-5 restored nucleational activity to the PS:PE CPLX; thus PS and Anx-5 proved to be critical for nucleation of mineral. Without Anx-5, induction of mineral formation was slow unless high levels of Ca(2+) were used. The presence of type II collagen in synthetic cartilage lymph improved both the rate and amount of mineral formation but did not enhance nucleation. This stimulatory effect required the presence of the nonhelical telopeptides. Although type X collagen slowed induction, it also increased the rate and amount of mineral formation. Both type II and X collagens markedly increased mineral formation by the MV-like CPLX, requiring Anx-5 to do so. Thus, Anx-5 enhances nucleation by the CPLXs and couples this to propagation of mineral formation by the cartilage collagens.

  15. Biocompatible and colloidally stabilized mPEG-PE/calcium phosphate hybrid nanoparticles loaded with siRNAs targeting tumors.

    Science.gov (United States)

    Gao, Pei; Zhang, Xiangyu; Wang, Hongzhi; Zhang, Qinghong; Li, He; Li, Yaogang; Duan, Yourong

    2016-01-19

    Calcium phosphate nanoparticles are safe and effective delivery vehicles for small interfering RNA (siRNA), as a result of their excellent biocompatibility. In this work, mPEG-PE (polyethylene glycol-L-α-phosphatidylethanolamine) was synthesized and used to prepare nanoparticles composed of mPEG-PE and calcium phosphate for siRNA delivery. Calcium phosphate and mPEG-PE formed the stable hybrid nanoparticles through self-assembly resulting from electrostatic interaction in water. The average size of the hybrid nanoparticles was approximately 53.2 nm with a negative charge of approximately -16.7 mV, which was confirmed by dynamic light scattering (DLS) measurements. The nanoparticles exhibited excellent stability in serum and could protect siRNA from ribonuclease (RNase) degradation. The cellular internalization of siRNA-loaded nanoparticles was evaluated in SMMC-7721 cells using a laser scanning confocal microscope (CLSM) and flow cytometry. The hybrid nanoparticles could efficiently deliver siRNA to cells compared with free siRNA. Moreover, the in vivo distribution of Cy5-siRNA-loaded hybrid nanoparticles was observed after being injected into tumor-bearing nude mice. The nanoparticles concentrated in the tumor regions through an enhanced permeability and retention (EPR) effect based on the fluorescence intensities of tissue distribution. A safety evaluation of the nanoparticles was performed both in vitro and in vivo demonstrating that the hybrid nanoparticle delivery system had almost no toxicity. These results indicated that the mPEG-PE/CaP hybrid nanoparticles could be a stable, safe and promising siRNA nanocarrier for anticancer therapy.

  16. Synthesis of some calcium phosphate crystals using the useful biomass for immobilization of microorganisms

    Energy Technology Data Exchange (ETDEWEB)

    Kohiruimaki, T, E-mail: kohi@hi-tech.ac.jp [Department of Technology, Hachinohe Institute of Technology, 88-1 Myo-oobiraki, Hachinohe-shi 031-8501 (Japan)

    2011-10-29

    Three sources of biomass generated by primary industry were used as the raw material for the synthesis of calcium phosphate crystals. Phosphoric acid was extracted from burned rice chaff using a 30% nitric acid solution, while scallop shells and gypsum of plasterboard were used as calcium sources. The calcium phosphate crystals were synthesized by a method involving homogeneous precipitation, and the relationship between the composition and shape of the crystals and the pH at the time of the precipitation was investigated. Monetite crystals in a petal form with a diameter ranging from 0.1 to 2 {mu}m were precipitated at pH 2.0, while granular apatite crystals with a mean diameter of 1 {mu}m were precipitated at pH 6.0. We also investigated the ability of the synthesized calcium phosphate crystals to immobilize lactic acid bacteria for practical use in industrial bioreactor. It was determined that monetite crystals with a diameter of 2 {mu}m had the highest ability to fix lactic acid bacteria. The population of lactic acid bacteria was estimated to exceed 1,300 bacteria per crystal surface of 50 {mu}m{sup 2} suggesting that these crystals may be of practical use in industrial fermenters.

  17. Synthesis of some calcium phosphate crystals using the useful biomass for immobilization of microorganisms

    Science.gov (United States)

    Kohiruimaki, T.

    2011-10-01

    Three sources of biomass generated by primary industry were used as the raw material for the synthesis of calcium phosphate crystals. Phosphoric acid was extracted from burned rice chaff using a 30% nitric acid solution, while scallop shells and gypsum of plasterboard were used as calcium sources. The calcium phosphate crystals were synthesized by a method involving homogeneous precipitation, and the relationship between the composition and shape of the crystals and the pH at the time of the precipitation was investigated. Monetite crystals in a petal form with a diameter ranging from 0.1 to 2 μm were precipitated at pH 2.0, while granular apatite crystals with a mean diameter of 1 μm were precipitated at pH 6.0. We also investigated the ability of the synthesized calcium phosphate crystals to immobilize lactic acid bacteria for practical use in industrial bioreactor. It was determined that monetite crystals with a diameter of 2 μm had the highest ability to fix lactic acid bacteria. The population of lactic acid bacteria was estimated to exceed 1,300 bacteria per crystal surface of 50 μm2 suggesting that these crystals may be of practical use in industrial fermenters.

  18. An experimental approach to the study of the rheology behaviour of synthetic bone calcium phosphate cements

    Energy Technology Data Exchange (ETDEWEB)

    Friberg, J.; Fernandez, E.; Sarda, S.; Nilsson, M.; Ginebra, M.P.; Planell, J.A. [Universidad Politecnica de Catalunya, Barcelona (Spain). Dept. of Materials Science and Metallurgical Engineering; Martinez, S. [Barcelona Univ. (Spain). Mineralogia i Recursos Minerals

    2001-07-01

    Calcium phosphate cements were developed to fit surgical needs in biomedical fields such as odontology or traumatology. Nowadays, a broad field of new applications have been found for this kind of materials. Drug delivery systems, tissue-engineering scaffolds and osteoporotic bone filling applications are some of the new fields that are being benefited with these materials. Looking at both, commercial and new experimental calcium phosphate cements it is found that {alpha}-tricalcium phosphate is the main reactive powder responsible for the setting and the hardening of the cement. Thus, it is important to know how {alpha}-tricalcium phosphate affects injectability of these cements. The aim of this study was to investigate the rheological behaviour of {alpha}-tricalcium phosphate slurries in order to know how the cement injectability should be modified. Factors such as liquid to powder ratio, particle size of the main reactive powder and the addition of dispersants have been considered. The results showed that viscosity decreased when particle size of reactant was increased and when liquid to powder ratio was increased. It was also found that a minimum of viscosity exists at an optimum value of the weight percentage of dispersant. (orig.)

  19. On the Pressure-Induced Loss of Crystallinity in Zinc- and Calcium-Phosphates

    Energy Technology Data Exchange (ETDEWEB)

    Shakhvorostov, D.; Mosey, N; Munoz-Paniagua, D; Pereira, G; Song, Y; Kasrai, M; Norton, P; Müser, M

    2008-01-01

    A recently suggested mechanism for the stress memory of various metal phosphates is investigated experimentally. Based on first-principles simulations [N. J. Mosey et al., Science 307, 1612 (2005)], it had been argued that atoms with flexible coordination, such as zinc or heavy-metal cations, act as network-forming agents, undergoing irreversible pressure-induced changes in bonding that lead to increased connectivity between phosphate anions. In the present study, orthophosphates of zinc and calcium were exposed to high pressures on surfaces and in diamond anvil cells. An additional set of first-principles simulations was accomplished on ?-orthophosphate of zinc, which suggested that this material was already cross-linked before compression but that it nevertheless underwent a reversible coordination change under pressure in agreement with the experimental results presented here. Raman spectra indicate an irreversible, pressure-induced loss of long-range crystallinity. The pressures required to induce these changes are around 7 GPa for the zinc phosphates, while they are close to 21 GPa for the calcium phosphates. Hydrogenation of the metal phosphate lowers the threshold pressure by approximately 2-3 GPa in both cases. Moreover, ?-orthophosphate of zinc could be partially amorphisized under nonisotropic pressure on copper foils.

  20. Study of calcium phosphate (DCPD electrodeposition process on a Mg-3Al-1Zn magnesium alloy surface

    Directory of Open Access Journals (Sweden)

    Filip Pastorek

    2013-02-01

    Full Text Available Evaluation of calcium phosphating process realized on Mg-3Al-1Zn alloy surface after grinding was investigated by electrochemical tests supported by photodocumentation. The electrodeposition treatment was performed by electrochemical method in water solution of Ca(NO32.4H2O, (NH42HPO4 and H2O2. The formation of calcium phosphate was divided into several stages and described using light microscopy. The progress in corrosion protection of created calcium phosphate layer in 0.9% NaCl after particular electrodeposition steps was evaluated by electrochemical impedance spectroscopy. The results in the form of Nyquist plots were analyzed using equivalent circuits.

  1. STUDY OF CALCIUM PHOSPHATE (DCPD ELECTRODEPOSITION PROCESS ON THE Mg-3Al-1Zn MAGNESIUM ALLOY SURFACE

    Directory of Open Access Journals (Sweden)

    Filip Pastorek

    2013-02-01

    Full Text Available Evaluation of calcium phosphating process realized on the Mg-3Al-1Zn alloy surface after grinding was investigated by electrochemical tests supported by photodocumentation. The electrodeposition treatment was performed by electrochemical method in water solution of Ca(NO32.4H2O, (NH42HPO4 and H2O2. The formation of calcium phosphate was divided into several stages and described using light microscopy. The progress in corrosion protection of created calcium phosphate layer in 0.9% NaCl after particular electrodeposition steps was evaluated by electrochemical impedance spectroscopy. The results in the form of Nyquist plots were analyzed using equivalent circuits.

  2. The progress of early phase bone healing using porous granules produced from calcium phosphate cement

    Directory of Open Access Journals (Sweden)

    Jungbluth P

    2010-05-01

    Full Text Available Abstract Objective Bone grafting is a vital component in many surgical procedures to facilitate the repair of bone defects or fusions. Autologous bone has been the gold standard to date in spite of associated donor-site morbidity and the limited amount of available donor bone. The aim of this study was to investigate the progress of bone regeneration and material degradation of calcium phosphate granules (CPG produced from a calcium phosphate self-setting cement powder compared to the use of autologous bone grafting in the treatment of "critical size defects" on load-bearing long bones of minipigs. Methods A critical size defect in the tibial metaphysis of 16 mini-pigs was filled either with autologous cancellous graft or with micro- and macroporous carbonated, apatic calcium phosphate granules (CPG produced from a calcium phosphate self-setting cement powder. After 6 weeks, the specimens were assessed by X-ray and histological evaluation. The amount of new bone formation was analysed histomorphometrically. Results The semi-quantitative analysis of the radiological results showed a complete osseous bridging of the defect in three cases for the autograft group. In the same group five animals showed a beginning, but still incomplete bridging of the defect, whereas in the CPG group just two animals developed this. All other animals of the CPG group showed only a still discontinuous new bone formation. Altogether, radiologically a better osseous bridging was observed in the autograft group compared to the CPG group. Histomorphometrical analysis after six weeks of healing revealed that the area of new bone was significantly greater in the autograft group concerning the central area of the defect zone (p Conclusions Within the limits of the present study it could be demonstrated that autologous cancellous grafts lead to a significantly better bone regeneration compared to the application of calcium phosphate granules (CPG produced from a calcium

  3. Microanalyses of the hydroxyl-poly-calcium sodium phosphate coatings produced by ion beam assisted deposition

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Thin calcium phosphate coatings on titanium alloy substrates wereprepared by Ar+ ion beam assisted deposition (IBAD) from hydroxyl-poly-calciumsodium phosphate (HPPA) target. The coatings were analyzed by XRD, FTIR, XPS.These analyses revealed that the as-deposited films were amorphous or no apparentcrystallinity. No distinct absorption band of the hydroxyl group was observed in FTIRspectra of the coatings but new absorption bands were presented for CO3-2. Thecalcium to phosphorous ratio of these coatings in different IBAD conditions variedfrom 0.46 to 3.36.

  4. Precipitation of calcium phosphate at 40° C from neutral solution

    Science.gov (United States)

    Lundager Madsen, Hans E.; Christensson, Finn

    1991-12-01

    Calcium phosphate formation was studied in the pH range 5brushite (CaHPO 4·2H 2O) is the role product, and octacalcium phosphate predominates at low concentrations. ACP is subsequently transformed into brushite or apatite (Ca 5OH(PO 4) 3), the latter always crytocrystalline, but brushite crystals often redissolve and leave apatite as the end product. The formation and evolution of precipitates are chiefly governed by solubilities of the different crystalline phases; for apatite, the excess solubility of small crystals as determined by the Gibbs-Kelvin equation plays an important role.

  5. [Cognitive Function and Calcium. The relationship between inositol phosphates and brain function].

    Science.gov (United States)

    Nagata, Eiichiro

    2015-02-01

    Inositol phosphates are produced depending on the numbers of the phosphate group which is added to the inositol ring which is 6 membered ring derived from a component of a biological membrane. Inositol 1, 4, 5 trisphosphate (IP3) operates on IP3 receptor on the endoplasmic reticulum, and is related to a release of calcium in the cell. IP3 is associated with various brain functions and neurodegenerative disorders. Moreover, there are IP4, IP5, IP6 and IP7 such as inositol polyphosphates in mammals. Notably, inositol hexakisphoshate kinase (IP6) which phosphorylates IP6 to IP7 plays important roles in the pathophysiology of various neurodegenerative disorders.

  6. Systemic delivery of siRNA by hyaluronan-functionalized calcium phosphate nanoparticles for tumor-targeted therapy

    Science.gov (United States)

    Qiu, Chong; Wei, Wei; Sun, Jing; Zhang, Hai-Tao; Ding, Jing-Song; Wang, Jian-Cheng; Zhang, Qiang

    2016-06-01

    In this study, hyaluronan (HA)-functionalized calcium phosphate nanoparticles (CaP-AHA/siRNA NPs) were developed for an injectable and targetable delivery of siRNA, which were prepared by coating the alendronate-hyaluronan graft polymer (AHA) around the surface of calcium phosphate-siRNA co-precipitates. The prepared CaP-AHA/siRNA NPs had a uniform spherical core-shell morphology with an approximate size of 170 nm and zeta potential of -12 mV. The coating of hydrophilic HA improved the physical stability of nanoparticles over one month due to the strong interactions between phosphonate and calcium. In vitro experiments demonstrated that the negatively charged CaP-AHA/siRNA NPs could effectively deliver EGFR-targeted siRNA into A549 cells through CD44-mediated endocytosis and significantly down-regulate the level of EGFR expression. Also, the internalized CaP-AHA/siRNA NPs exhibited a pH-responsive release of siRNA, indicating that the acidification of lysosomes probably facilitated the disassembling of nanoparticles and the resultant ions sharply increased the inner osmotic pressure and thus expedited the release of siRNA from late lysosomes into the cytoplasm. Furthermore, in vivo tumor therapy demonstrated that high accumulation of CaP-AHA/siEGFR NPs in tumor led to a significant tumor growth inhibition with a specific EGFR gene silencing effect after intravenous administration in nude mice xenografted with A549 tumor, along with a negligible body weight loss. These results suggested that the CaP-AHA/siRNA NPs could be an effective and safe systemic siRNA delivery system for a RNAi-based tumor targeted therapy strategy.In this study, hyaluronan (HA)-functionalized calcium phosphate nanoparticles (CaP-AHA/siRNA NPs) were developed for an injectable and targetable delivery of siRNA, which were prepared by coating the alendronate-hyaluronan graft polymer (AHA) around the surface of calcium phosphate-siRNA co-precipitates. The prepared CaP-AHA/siRNA NPs had a uniform

  7. Proliferation and differentiation of osteoblast-like MC3T3-E1 cells on biomimetically and electrolytically deposited calcium phosphate coatings.

    Science.gov (United States)

    Wang, Jiawei; de Boer, Jan; de Groot, Klaas

    2009-09-01

    Biomimetic and electrolytic deposition are versatile methods to prepare calcium phosphate coatings. In this article, we compared the effects of biomimetically deposited octacalcium phosphate and carbonate apatite coatings as well as electrolytically deposited carbonate apatite coating on the proliferation and differentiation of mouse osteoblast-like MC3T3-E1 cells. It was found that MC3T3-E1 cells cultured on the biomimetically deposited carbonate apatite coating demonstrated the greatest proliferation rate and the highest differentiation potential. Cells on the biomimetically deposited octacalcium phosphate coating had lower proliferation rate before day 7, but higher after that, than those on the electrolytically deposited carbonate apatite coating. There was no difference on the expression of early differentiation markers, that is, alkaline phosphatase activity and collagen content, between biomimetically deposited octacalcium phosphate and electrolytically deposited carbonate apatite coatings. However, higher expression of late differentiation markers, that is, osteocalcin and bone sialoprotein mRNA, was found on the biomimetically deposited octacalcium phosphate coating on day 14. These results suggest that the difference in in vitro osteoblast cell performance of calcium phosphate coatings might relate to their physicochemical properties. Biomimetic carbonate apatite coating is the most favorable surface for the proliferation and differentiation of MC3T3-E1 cells.

  8. Biological influence of Ca/P ratio on calcium phosphate coatings by sol-gel processing

    Energy Technology Data Exchange (ETDEWEB)

    Catauro, M., E-mail: michelina.catauro@unina2.it [Department of Industrial and Information Engineering, Second University of Naples, Via Roma 29 (Italy); Papale, F. [Department of Industrial and Information Engineering, Second University of Naples, Via Roma 29 (Italy); Sapio, L.; Naviglio, S. [Department of Biochemistry, Biophysics and General Pathology, Second University of Naples, Via L. De Crecchio 7, 80138 Naples (Italy)

    2016-08-01

    The objective of this work has been to develop low temperature sol-gel glass coatings to modify the substrate surface and to evaluate their bioactivity and biocompatibility. Glasses, based on SiO{sub 2}·CaO·P{sub 2}O{sub 5}, were synthesized by the sol-gel technique using tetraethyl orthosilicate, calcium nitrate tetrahydrate and triethyl phosphate as precursors of SiO{sub 2}, CaO and P{sub 2}O{sub 5}, respectively. Those materials, still in the sol phase, have been used to coat substrates by means of the dip-coating technique. Attenuated total reflectance Fourier transform infrared (ATR-FTIR) has been used for characterize coatings and a microstructural analysis has been obtained using scanning electron microscopy (SEM). The potential applications of the coatings in the biomedical field were evaluated by bioactivity and biocompatibility tests. The coated substrate was immersed in simulated body fluid (SBF) for 21 days and the hydroxyapatite deposition on its surface was subsequently evaluated via SEM-EDXS analysis, as an index of bone-bonding capability. In order to study the cell behavior and response to our silica based materials, prepared via the sol-gel method, with various Ca/P ratio and coating substrate, we have used the human osteoblast-like U2OS cell line. - Highlights: • Coatings consisting of SiO{sub 2}·CaO·P{sub 2}O{sub 5} glasses were prepared via sol-gel dip coating. • Ca/P molar ratio affects the film morphology and biocompatibility. • Higher cell proliferation was found in response to higher Ca/P ratios coatings. • A growth cell proliferation inhibition was observed in response to lower Ca/P ratio.

  9. Fine-Tuning of Polymeric Resins and Their Interfaces with Amorphous Calcium Phosphate. A Strategy for Designing Effective Remineralizing Dental Composites

    OpenAIRE

    Drago Skrtic; Antonucci, Joseph M.

    2010-01-01

    For over a decade our group has been designing, preparing and evaluating bioactive, remineralizing composites based on amorphous calcium phosphate (ACP) fillers embedded in polymerized methacrylate resin matrices. In these studies a major focus has been on exploring structure-property relationships of the matrix phase of these composites on their anti-cariogenic potential. The main challenges were to gain a better understanding of polymer matrix/filler interfacial properties through controlli...

  10. Stabilization/solidification of mercury-contaminated waste ash using calcium sodium phosphate (CNP) and magnesium potassium phosphate (MKP) processes.

    Science.gov (United States)

    Cho, Jae Han; Eom, Yujin; Lee, Tai Gyu

    2014-08-15

    This study examined the stabilization and solidification (S/S) of mercury (Hg)-contaminated waste ash generated from an industrial waste incinerator using chemically bonded phosphate ceramic (CBPC) technology. A magnesium potassium phosphate (MKP; MgKPO4 · 6H2O) ceramic, fabricated from MgO and KH2PO4, and a calcium sodium phosphate (CNP; CaNaPO4) ceramic, fabricated from CaO and Na2HPO4, were used as solidification binders in the CBPC process, and Na2S or FeS was added to each solidification binder to stabilize the Hg-contaminated waste ash. The S/S processes were conducted under various operating conditions (based on the solidification binder and stabilization reagent, stabilization reagent dosage, and waste loading ratio), and the performance characteristics of the S/S sample under each operating condition were compared, including the Hg leaching value and compressive strength. The Hg leaching value of untreated Hg-contaminated waste ash was 231.3 μg/L, whereas the S/S samples treated using the MKP and CNP processes exhibited Hg leaching values below the universal treatment standard (UTS) limit (25 μg/L). Although the compressive strengths of the S/S samples decreased as the sulfide dosage and waste loading ratio were increased, most of the S/S samples fabricated by the MKP and CNP processes exhibited good mechanical properties.

  11. Preparation of calcium phosphate cement for artificial rib scaffold and its degradability in vivo%人工肋骨支架多孔磷酸钙的制备及体内降解研究

    Institute of Scientific and Technical Information of China (English)

    唐华; 徐志飞; 刘昌胜; 秦雄; 赵学维; 薛磊

    2008-01-01

    目的 对多孔磷酸钙(CPC)体内降解情况进行研究,为其作为组织工程化人工肋骨支架提供实验基础.方法 将CPC材料埋植于兔皮下,并于预定的时间点将材料取出,称重并送扫描电镜检查,以观察其降解情况;其周围组织则进行苏木素-伊红(HE)染色和透射电镜检查,以观察其炎症反应和生物相容性.结果 CPC材料在术后2、4、8、12、24周的生物吸收率分别为(2.500±0.098)%、(7.000±0.167)%、(10.000±0.242)%、(14.000±0.251)%、(30.000±0.177)%,降解速度平稳,能有效维持缺损部位的稳定性;HE染色和透射电镜结果 显示其炎症反应于4周时消失,有良好的生物相容性.结论 CPC的体内降解速度平稳,组织相容性好,是承重部位和非承重部位的良好组织工程支架.%Objective In order to provide the further evidence of possibiLty of Calcium phosvhate cement(CPC)as the suitable scaffold for tissue engineered artificial rib,the degradation of CPC in vivo was studied.Methods The CPC materials were implanted subcutaneously in rabbits.CPC materials were taken out at the seheduled time points,weighed and examined under a transmission electron microscope.CPC degradation was observed.The tissues around the CPC materials were observed by HE staining and the transmission electron microscope.Results The mass weight loss rate of CPC at 2,4,8,12,24 week was(2.500±0.098)%,(7.000±0.167)%,(10.000±0.242)%,(14.000±0.251)%and (30.000±0.177)% respectively.The speed of degradation was stable.The results of HE staining and transmission electron microscopy revealed that the CPC material had a good compatibility wlth body.Conclusion CPC is a suitable scaffold for tissue engineered artifieial rib.

  12. Calcium chloride and tricalcium phosphate effects on the pink color defect in cooked ground and intact turkey breast.

    Science.gov (United States)

    Sammel, L M; Claus, J R

    2007-12-01

    Calcium chloride (250, 500ppm) was examined for its ability to reduce the pink color defect induced by sodium nitrite (10ppm) and nicotinamide (1.0%) in cooked ground turkey in the presence and absence of sodium tripolyphosphate (0.25, 0.5%) and sodium citrate (0.5, 1.0%). The ability of tricalcium phosphate (0.1-0.5%) to reduce pink cooked color also was evaluated in ground turkey and both calcium chloride and tricalcium phosphate were tested for their effects on pink cooked color in whole breast muscle. The combination of calcium chloride and sodium tripolyphosphate, not calcium chloride alone, was necessary for a reduction in pink cooked color induced by nicotinamide. Subsequently, in the presence of phosphate, both calcium chloride and sodium citrate reduced pink cooked color and were most effective in combination. Tricalcium phosphate also was capable of reducing pink cooked color in ground turkey, however substituting tricalcium phosphate for sodium tripolyphosphate resulted in lower pH and cooking yields. Neither calcium chloride nor tricalcium phosphate was capable of reducing pink cooked color in whole turkey breast. Currently, a combination of sodium tripolyphosphate, calcium chloride, and sodium citrate represents the most suitable means for reducing or preventing the pink color defect in uncured ground turkey.

  13. Manufacturing of calcium phosphate scaffolds by pseudomorphic transformation of gypsum

    Energy Technology Data Exchange (ETDEWEB)

    Araujo Batista, H. de.; Batista Cardoso, M.; Sales Vasconcelos, A.; Vinicius Lia Fook, M.; Rodriguez Barbero, M. A.; Garcia Carrodeguas, R.

    2016-08-01

    Carbonated hydroxyapatite (CHAp) and β-tricalcium phosphate (β-TCP) have been employed for decades as constituents of scaffolds for bone regeneration because they chemically resemble bone mineral. In this study, the feasibility to manufacture CHAp/β-TCP scaffolds by pseudomorphic transformation of casted blocks of gypsum was investigated. The transformation was carried out by immersing the precursor gypsum block in 1 M (NH{sub 4}){sub 2}HPO{sub 4}/1.33 M NH{sub 4}OH solution with liquid/solid ratio of 10 mL/g and autoclaving at 120 degree centigrade and 203 kPa (2 atm) for 3 h at least. Neither shape nor dimensions significantly changed during transformation. The composition of scaffolds treated for 3 h was 70 wt.% CHAp and 30 wt.% β-TCP, and their compressive and diametral compressive strengths were 6.5 ± 0.7 and 5.3 ±0.7 MPa, respectively. By increasing the time of treatment to 6 h, the composition of the scaffold enriched in β-TCP (60 wt.% CHAp and 40 wt.% β-TCP) but its compressive and diametral compressive strengths were not significantly affected (6.7 ± 0.9 and 5.4 ± 0.6 MPa, respectively). On the basis of the results obtained, it was concluded that this route is a good approach to the manufacturing of biphasic (CHAp/β-TCP) scaffolds from previously shaped pieces of gypsum. (Author)

  14. Bioactive behavior of silicon substituted calcium phosphate based bioceramics for bone regeneration.

    Science.gov (United States)

    Khan, Ather Farooq; Saleem, Muhammad; Afzal, Adeel; Ali, Asghar; Khan, Afsar; Khan, Abdur Rahman

    2014-02-01

    Bone graft substitutes are widely used for bone regeneration and repair in defect sites resulting from aging, disease, trauma, or accident. With invariably increasing clinical demands, there is an urgent need to produce artificial materials, which are readily available and are capable of fast and guided skeletal repair. Calcium phosphate based bioactive ceramics are extensively utilized in bone regeneration and repair applications. Silicon is often utilized as a substituent or a dopant in these bioceramics, since it significantly enhances the ultimate properties of conventional biomaterials such as surface chemical structure, mechanical strength, bioactivity, biocompatibility, etc. This article presents an overview of the silicon substituted bioceramics, which have emerged as efficient bone replacement and bone regeneration materials. Thus, the role of silicon in enhancing the biological performance and bone forming capabilities of conventional calcium phosphate based bioceramics is identified and reviewed.

  15. Calcium phosphate nanoparticles as versatile carrier for small and large molecules across cell membranes

    Energy Technology Data Exchange (ETDEWEB)

    Sokolova, Viktoriya; Rotan, Olga; Klesing, Jan [University of Duisburg-Essen, Inorganic Chemistry and Center for Nanointegration Duisburg-Essen (CeNIDE) (Germany); Nalbant, Perihan [University of Duisburg-Essen, Faculty of Biology, Institute of Molecular Cell Biology (Germany); Buer, Jan; Knuschke, Torben; Westendorf, Astrid M. [University Hospital Essen, University of Duisburg-Essen, Institute of Medical Microbiology (Germany); Epple, Matthias, E-mail: matthias.epple@uni-due.de [University of Duisburg-Essen, Inorganic Chemistry and Center for Nanointegration Duisburg-Essen (CeNIDE) (Germany)

    2012-06-15

    The successful transport of molecules across the cell membrane is a key point in biology and medicine. In most cases, molecules alone cannot penetrate the cell membrane, therefore an efficient carrier is needed. Calcium phosphate nanoparticles (diameter: 100-250 nm, depending on the functionalization) were loaded with fluorescent oligonucleotides, peptide, proteins, antibodies, polymers or porphyrins and characterized by dynamic light scattering, nanoparticle tracking analysis and scanning electron microscopy. Any excess of molecules was removed by ultracentrifugation, and the dissolved molecules at the same concentration were used as control. The uptake of such fluorescence-labeled nanoparticles into HeLa cells was monitored by fluorescence microscopy and confocal laser scanning microscopy. Calcium phosphate nanoparticles were able to transport all molecules across the cell membrane, whereas the dissolved molecules alone were taken up only to a very small extent or even not at all.

  16. Influence of surface treatment of carbon fibers on electrochemical crystallization of calcium phosphate

    Institute of Scientific and Technical Information of China (English)

    TAO Ke; HUANG Su-ping; ZHOU Ke-chao

    2005-01-01

    Electrodeposition technique was used to coat calcium phosphate on carbon fiber which can be used to reinforce hydroxyapatite. The differences between fibers treated with and without nitric acid in electrodeposition were evaluated. The X-ray diffractometry results show that CaHPO4·2H2O is obtained as the kind of calcium phosphate coating on carbon fiber. The scanning electron microscopy photographs and deposit kinetic curve indicate that the influences of the functional group attained by nitric acid treatment, the crystal morphology and crystallization of the coating layers on the fiber with and without treatment rate are obviously different. The functional group, especially the acidic group, can act as nucleation centers of electrochemical crystallization.

  17. Investigation on the biomimetic influence of biopolymers on calcium phosphate precipitation-Part 1: Alginate

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira de Lima, Daniel; Gomes Aimoli, Cassiano [Faculdade de Engenharia Quimica, Unicamp, CP6066 CEP13083-970, Campinas, SP (Brazil); Beppu, Marisa Masumi, E-mail: beppu@feq.unicamp.br [Faculdade de Engenharia Quimica, Unicamp, CP6066 CEP13083-970, Campinas, SP (Brazil)

    2009-05-05

    The understanding of how macromocules act in precipitation of inorganic phases is the key knowledge that is needed to establish the foundation to mimic nature and produce materials with high mechanical modulus besides outstanding optical and thermal properties. This study investigated how addition of small amounts of alginate (7-70 ppm), that presents many carboxylic groups, affects phase distribution and morphology of calcium phosphates, obtained through precipitation and further submitted to calcination and sintering. The results lead to the conclusion that alginate action is dynamic, where alginate molecules act as templates to nucleation, and most of the biopolymer remains in solution even when all calcium phosphate has precipitated. However, despite the effect on phase composition being mainly related to the system's kinetics, alginate does present thermodynamic interaction with the precipitates. It is probable that it acts by reducing the free energy of nucleation, as in heterogeneous nucleation processes.

  18. A brief review of calcium phosphate conversion coating on magnesium and its alloys

    Science.gov (United States)

    Zaludin, Mohd Amin Farhan; Jamal, Zul Azhar Zahid; Jamaludin, Shamsul Baharin; Derman, Mohd Nazree

    2016-07-01

    Recent developments have shown that magnesium is a promising candidate to be used as a biomaterial. Owing to its light weight, biocompatibility and compressive strength comparable with natural bones makes magnesium as an excellent choice for biomaterial. However, high reactivity and low corrosion resistance properties have restricted the application of magnesium as biomaterials. At the moment, several strategies have been developed to solve this problem. Surface modification of magnesium is one of the popular solutions to solve the problem. Among many techniques developed in the surface modification, conversion coating method is one of the simple and effective techniques. From various types of conversion coating, calcium phosphate-based conversion coating is the most suitable for biomedical fields. This paper reviews some studies on calcium phosphate coating on Mg and its alloys via chemical conversion method and discusses some factors determining the coating performance.

  19. Calcium phosphate nanocoatings and nanocomposites, part I: recent developments and advancements in tissue engineering and bioimaging.

    Science.gov (United States)

    Choi, Andy H; Ben-Nissan, Besim

    2015-07-01

    A number of materials have been applied as implant coatings and as tissue regeneration materials. Calcium phosphate holds a special consideration, due to its chemical similarity to human bone and, most importantly, its dissolution characteristics, which allow for bone growth and regeneration. The applications of molecular and nanoscale-based biological materials have been and will continue to play an ever increasing role in enhancing and improving the osseointegration of dental and orthopedic implants. More recently, extensive research efforts have been focused on the development and applications of fluorescent nanoparticles and nanocoatings for in vivo imaging and diagnostics as well as devising methods of adding luminescent or fluorescent capabilities to enhance the in vivo functionality of calcium phosphate-based biomedical materials.

  20. Characterization of calcium phosphate coating and zinc incorporation on the porous alumina scaffolds

    Directory of Open Access Journals (Sweden)

    Hermes de Souza Costa

    2007-03-01

    Full Text Available Bone ingrowth requires materials with the existence of open and interconnected pores with diameters larger than 150 µm for proper circulation of nutrients. Such materials must possess enough mechanical strength to avoid failure whilst offering a bioactive surface for bone regeneration. We have developed porous ceramic alumina scaffold with compressive strength that achieves 3.3 MPa by replication method by using the network structure of cellular polymer foam. However, the biocompatibility of ceramics based on Al2O3 requires further improvement so that it could have strong bonding to natural bone tissue. To address this problem of the interface between alumina and bone, we have developed a novel calcium phosphate with Zn2+ (CaP-Zn coating onto porous alumina ceramic scaffold by impregnating with calcium phosphate/poly(vinyl alcohol slurry. The tri-dimensional alumina scaffold coated with CaP-Zn was extensively characterized by SEM, EDS and FTIR.

  1. Early resorption of an artificial bone graft made of calcium phosphate for cranioplasty: case report

    Directory of Open Access Journals (Sweden)

    Monaco BA

    2013-11-01

    Full Text Available Bernardo Assumpção de Monaco, Erich Talamoni Fonoff, Manoel Jacobsen TeixeiraDivision of Functional Neurosurgery, Department of Neurology, Hospital das Clinicas, University of São Paulo Medical School, São Paulo, BrazilAbstract: The treatment of uncomplicated osteoma consists of an en bloc resection, or curettage, of the tumor, followed by cranioplasty. Here, we present a case report of a patient treated for a parietal osteoma, followed by a calcium phosphate cranioplasty, with early resorption after 3 months, which was presented by a sinking flap above the resection area. This case suggests that synthetic cranioplasty should be preferred, even in small skull-gap areas.Keywords: cranioplasty, bone cement, osteoma, calcium phosphate, resorption

  2. The use of calcium phosphate-based biomaterials in implant dentistry.

    Science.gov (United States)

    Xie, Cheng; Lu, Hong; Li, Wei; Chen, Fa-Ming; Zhao, Yi-Min

    2012-03-01

    Since calcium phosphates (CaPs) were first proposed, a wide variety of formulations have been developed and continuously optimized, some of which (e.g. calcium phosphate cements, CPCs) have been successfully commercialized for clinical applications. These CaP-based biomaterials have been shown to be very attractive bone substitutes and efficient drug delivery vehicles across diverse biomedical applications. In this article, CaP biomaterials, principally CPCs, are addressed as alternatives/complements to autogenous bone for grafting in implant dentistry and as coating materials for enhancing the osteoinductivity of titanium implants, highlighting their performance benefits simultaneously as carriers for growth factors and as scaffolds for cell proliferation, differentiation and penetration. Different strategies for employing CaP biomaterials in dental implantology aim to ultimately reach the same goal, namely to enhance the osseointegration process for dental implants in the context of immediate loading and to augment the formation of surrounding bone to guarantee long-term success.

  3. Kinetics of phosphate absorption in lactating dairy cows after enteral administration of sodium phosphate or calcium phosphate salts.

    Science.gov (United States)

    Grünberg, Walter; Dobbelaar, Paul; Breves, Gerhard

    2013-09-28

    Hypophosphataemia is frequently encountered in dairy cows during early lactation. Although supplementation of P is generally recommended, controversy exists over the suitability of oral P supplementation in animals with decreased or absent rumen motility. Since the effects of transruminal P absorption and the reticular groove reflex on the absorption kinetics of P are not well understood, it is unclear in how far treatment efficacy of oral P supplementation is affected by decreased rumen motility. Phosphate absorption was studied in six phosphate-depleted dairy cows fitted with rumen cannulas and treated with test solutions containing either NaH2PO4 or CaHPO4 with acetaminophen. Each animal was treated orally, intraruminally and intra-abomasally in randomised order. Absorption kinetics of P were studied and compared with the absorption kinetics of acetaminophen, a marker substance only absorbed from the small intestine. Intra-abomasal treatment with NaH2PO4 resulted in the most rapid and highest peaks in plasma inorganic P (Pi) concentration. Oral and intraruminal administration of NaH2PO4 resulted in similar increases in plasma Pi concentration from 4 to 7 h in both groups. Treatment with NaH2PO4 caused more pronounced peaks in plasma Pi concentration compared with CaHPO4. Neither transruminal P absorption nor the reticular groove reflex affected P absorption kinetics as determined by comparing plasma concentration–time curves of P and acetaminophen after administration of 1M-phosphate salt solutions. It is concluded that oral treatment with NaH2PO4 but not CaHPO4 is effective in supplementing P in hypophosphataemic cows with adequate rumen motility. Decreased rumen motility is likely to hamper the efficacy of oral phosphate treatment.

  4. Studies on the mechanisms underlying the transfer of calcium and phosphate from bone to blood

    Energy Technology Data Exchange (ETDEWEB)

    Brommage, Robert J. Jr.

    1978-01-01

    The skeleton is recognized as a crucial organ in the minute-to-minute regulation of the blood levels of calcium and phosphate. The fluxes of calcium and phosphate to and from bone greatly exceed the entry and exit of these ions occurring in the intestine and kidneys. Parathyroid hormone, calcitonin, and 1,25-dihydroxyvitamin D/sub 3/ (1,25-(OH)/sub 2/D/sub 3/ are known to influence the transfer of calcium and phosphate from bone to blood. Three mechanisms have been proposed to explain the hormonal control of the calcium and phosphate effluxes from bone. The concept of a bone membrane maintaining a distinct bone extracellular fluid composition has led to the pump and pH gradient theories. An alternate solubilizer theory proposes that bone cells secrete a substance which increases the solubility of the bone mineral. The bone membrane concept was originally proposed to explain the presence of the apparent anomalously high concentrations of potassium in the bone extracellular fluid. However, the available evidence does not allow an unambiguous decision concerning the presence of a bone membrane. Calvarial lactate production was unaltered by 1,25-(OH)/sub 2/D/sub 3/ treatment and consequently 1,25-(OH)/sub 2/D/sub 3/ does not appear to promote the mobilization of bone mineral through a lactate-mediated pH gradient mechanism. 1,25-(OH)/sub 2/D/sub 3/ did increase the solubility of non-vital bone, clearly demonstrating that the solubilizer mechanism is at least partially responsible for the mobilization of bone mineral and the regulation of blood levels of calcium and phosphate. Vitamin D-deficient female rats fed a 0.2% calcium, 0.4% phosphorous diet and supplemented with daily injections of 0.75 pmole of 1,25-(OH)/sub 2/D/sub 3/ were shown to be capable of bearing young. When the injections of 1,25-(OH)/sub 2/D/sub 3/ were terminated at delivery, the dams and pups showed signs of vitamin D deficiency approximately one week later.

  5. Calcium salts of keto-amino acids, a phosphate binder alternative for patients on CAPD.

    Science.gov (United States)

    Macia, M; Coronel, F; Navarro, J F; Gallego, E; Herrero, J A; Méndez, M L; Chahin, J; García, J

    1997-09-01

    Control of hyperphosphoremia is crucial to the prevention of secondary hyperparathyroidism. Calcium salts of keto-amino acids (KAA) were employed as phosphate binders in hemodialysis patients. We wanted to assess the efficacy of these substances as quelating agents in patients under continuous ambulatory peritoneal dialysis (CAPD). Also, as an amino acid supplement, we determined their possible effect on some parameters related to nutritional status. We studied 13 patients (7 M; 6 F) with a mean age of 45.2 +/- 17 years and a mean time on CAPD of 18.4 +/- 11.4 months. None had severe secondary hyperparathyroidism and/or clinically relevant aluminium intoxication. They were not receiving calcitriol and none were using low-calcium peritoneal dialysis fluids. All were under aluminum hydroxide (AlOH3) treatment and 8 patients also received calcium carbonate. These quelating agents were withdrawn and after 21 days (wash-out period) KAA were initiated. We analyzed serum levels of bone metabolism parameters (calcium, phosphate, osteocalcin [OC], intact parathyroid hormone [iPTH], alkaline phosphatase [AP]) and nutritional parameters (total protein, albumin, pre-albumin, transferrin) in four periods: (A) during AlOH3; (B) immediately after the washout period; (C) after 1.5 months; and (D) after 3 months of KAA therapy. In 5 patients serum aluminum level was also measured in periods (A) and (D). The serum phosphate level at period (B) was significantly higher than in other periods. After 3 months of treatment phosphate levels decreased significantly (A = 1.77 +/- 0.3 mmol/l vs D = 1.48 +/- 0.2; p < 0.05). Serum calcium levels increased, while iPTH and OC decreased (p = ns). AP remained stable during the study. All nutritional parameters increased at the end of the study (p = ns). Calcium salts of keto-amino acids showed to be an effective alternative to aluminum-containing phosphate binders. They were well tolerated, without relevant side-effects. These compounds could also

  6. Polyfunctional bioceramics based on calcium phosphate and M-type hexagonal ferrite for medical applications

    Science.gov (United States)

    Tkachenko, M. V.; Ol'khovik, L. P.; Kamzin, A. S.; Keshri, S.

    2014-01-01

    Magnetic biologically active ceramics based on calcium phosphate with a content of M-type hexagonal ferrite (HF) particles varying from 10 to 50 wt % has been synthesized and characterized. It has been found that the ceramics synthesized consists of a biocompatible carbonated hydroxyapatite (CHA) with the matrix containing M-type HF particles, leading to the magnetic characteristics of the ceramics synthesized being significantly higher than those of iron-oxide-modified bioglass ceramics used in medicine.

  7. Evaluation of implant calcium-phosphate materials depending on their mineral content

    Directory of Open Access Journals (Sweden)

    I. A. Talashova

    2012-01-01

    Full Text Available Biocompatibility of original implant calcium-phosphate materials was evaluated in the experiment on animals. The methods of radiological electron-probe microanalysis (REMA and light and scan electron microscopy (SEM were used. Studied materials had the properties of biodegradation, osteoinduction and osteoconduction at different extent. The materials with the composite maximally close to the the bone tissue had the greatest grade of biocompatibility.

  8. Water-Soluble Cellulose Derivatives Are Sustainable Additives for Biomimetic Calcium Phosphate Mineralization

    OpenAIRE

    2016-01-01

    The effect of cellulose-based polyelectrolytes on biomimetic calcium phosphate mineralization is described. Three cellulose derivatives, a polyanion, a polycation, and a polyzwitterion were used as additives. Scanning electron microscopy, X-ray diffraction, IR and Raman spectroscopy show that, depending on the composition of the starting solution, hydroxyapatite or brushite precipitates form. Infrared and Raman spectroscopy also show that significant amounts of nitrate ions are incorporated i...

  9. Development and characterisation of injectable calcium phosphate cements for use in vertebroplasty

    OpenAIRE

    2002-01-01

    The global objective of this thesis was to understand how the starting components of brushite cements influence the cement properties relevant for its use in vertebroplasty. Therefore, this work focussed on the following cement properties : mechanical strength, X-ray opacity and heat release upon setting. To carry out the global objective, a test protocol was first developed to characterise the mechanical properties of calcium phosphate cements. The Mohr's circles representation allowed to un...

  10. Development and characterisation of injectable calcium phosphate cements for use in vertebroplasty

    OpenAIRE

    2007-01-01

    The global objective of this thesis was to understand how the starting components of brushite cements influence the cement properties relevant for its use in vertebroplasty. Therefore, this work focussed on the following cement properties : mechanical strength, X-ray opacity and heat release upon setting. To carry out the global objective, a test protocol was first developed to characterise the mechanical properties of calcium phosphate cements. The Mohr's circles representation allowed to un...

  11. Synthesis of the refined calcium phosphate for bone china porcelain from oyster shell

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Y.H. [Department of Environmental Engineering, Kumsung Environment College (Korea, Republic of); Chang, Pok-Ki; Lim, Yong-Mu [Department of Inorganic Materials Engineering, Chonnam National University, Kwangju (Korea, Republic of)

    1997-11-01

    In this study, the oyster shell was calcined at high temperature (>800 deg. C) in reducing atmosphere to remove impurities, refined by elutriation and magnetic separator and reacted with phosphate to synthesized di-calcium phosphate(DCP). Studies for characteristic and application to bone china porcelain of this synthesized DCP were done. By thermal and ICP analysis, the oyster shell was composed of the calcium carbonate(CaCO{sub 3}) with impurities less than 2 wt%. Fe{sub 2}O{sub 3}, TiO{sub 2} and MnO belonged to colouring material and its contents were 0.17, 0.04 and 0.02 wt%, respectively. To research reducing behavior of colouring materials Fe{sub 2}/O{sub 3} was calcined at various temperature in reducing atmosphere. Metal Fe content increased with increasing calcining temperature. After pass through magnetic separator, contents of colouring material were reduced Fe{sub 2}O{sub 3} to 0.07, TiO{sub 2} to 0.03 and MnO to 0.01 wt%, respectively. Di-calcium phosphate synthesized from calcium-hydroxide based upon oyster shell and phosphate in ph=3.5 showed crystalline phase of brushite type, and changed to {Upsilon}-Ca{sub 2}P{sub 2}O{sub 7} at 450 deg. C. For DCP calcined at 1200.deg. C, average particle size was 3.56{mu}m, specific surface area was 1.6851 m{sup 2}/g and had no agglomerate. For bone china used the synthesized DCP, the high temperature slump was 7.5 mm, the shrinkage was 13.7% and the whiteness was 95.26% similarly situated with that of H company. (author). 18 refs., 9 figs., 4 tabs.

  12. Calcium phosphate cement as an alternative for formocresol in primary teeth pulpotomies

    OpenAIRE

    Bijimole Jose; Ratnakumari, N; Mira Mohanty; Varma, H. K.; Manoj Komath

    2013-01-01

    Background: Formocresol remains to be the preferred medicament in pulpotomy, despite the concerns regarding tissue devitalization and systemic toxicity. Several materials were used as alternatives, but none proved significantly advantageous. Of recent, calcium phosphate cement (CPC) has been projected as an ideal pulpotomy material considering its tissue compatibility and dentinogenic properties. This study explores the suitability of a CPC formulation for pulpotomy, in comparison with formoc...

  13. The In-situ Reinforcement of Calcium Phosphate Cement and Its Micro-structural Analysis

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Carbon nanotubes ( CNTs ) and polyacrylic acid were employed to modify the setting process and hydration products of β- TCP/ TTCP calcium phosphate cement. The micro-structure of hydration product and the fashion of how additives and hydration particles interconnected were investigated. With the modification effect of CNTs, the setting particles and CNTs got winded and interconnected and thus made the composite more compact and denser.

  14. Calcium phosphate thin films enhance the response of human mesenchymal stem cells to nanostructured titanium surfaces

    Directory of Open Access Journals (Sweden)

    Mura M McCafferty

    2014-05-01

    Full Text Available The development of biomaterial surfaces possessing the topographical cues that can promote mesenchymal stem cell recruitment and, in particular, those capable of subsequently directing osteogenic differentiation is of increasing importance for the advancement of tissue engineering. While it is accepted that it is the interaction with specific nanoscale topography that induces mesenchymal stem cell differentiation, the potential for an attendant bioactive chemistry working in tandem with such nanoscale features to enhance this effect has not been considered to any great extent. This article presents a study of mesenchymal stem cell response to conformal bioactive calcium phosphate thin films sputter deposited onto a polycrystalline titanium nanostructured surface with proven capability to directly induce osteogenic differentiation in human bone marrow–derived mesenchymal stem cells. The sputter deposited surfaces supported high levels of human bone marrow–derived mesenchymal stem cell adherence and proliferation, as determined by DNA quantification. Furthermore, they were also found to be capable of directly promoting significant levels of osteogenic differentiation. Specifically, alkaline phosphatase activity, gene expression and immunocytochemical localisation of key osteogenic markers revealed that the nanostructured titanium surfaces and the bioactive calcium phosphate coatings could direct the differentiation towards an osteogenic lineage. Moreover, the addition of the calcium phosphate chemistry to the topographical profile of the titanium was found to induce increased human bone marrow–derived mesenchymal stem cell differentiation compared to that observed for either the titanium or calcium phosphate coating without an underlying nanostructure. Hence, the results presented here highlight that a clear benefit can be achieved from a surface engineering strategy that combines a defined surface topography with an attendant, conformal

  15. The effect of calcium phosphate nanoparticles on hormone production and apoptosis in human granulosa cells

    Directory of Open Access Journals (Sweden)

    Gao Li

    2010-04-01

    Full Text Available Abstract Objectives Although many nanomaterials are being used in academia, industry and daily life, there is little understanding about the effects of nanoparticles on the reproductive health of vertebral animals, including human beings. An experimental study was therefore performed here to explore the effect of calcium phosphate nanoparticles on both steroid hormone production and apoptosis in human ovarian granulosa cells. Methods Calcium phosphate nanoparticles uptaking was evaluated by transmission electron microscopy (TEM. The cell cycle was assessed with propidium iodide-stained cells (distribution of cells in G0/G1, S, and G2/M phases by flow cytometry. The pattern of cell death (necrosis and apoptosis was analyzed by flow cytometry with annexin V-FITC/PI staining. The expression of mRNAs encoding P450scc, P450arom and StAR were determined by RT-PCR. Progesterone and estradiol levels were measured by radioimmunoassay. Results TEM results confirmed that calcium phosphate nanoparticles could enter into granulosa cells, and distributed in the membranate compartments, including lysosome and mitochondria and intracellular vesicles. The increased percentage of cells in S phase when cultured with nanoparticles indicated that there was an arrest at the checkpoint from phase S-to-G2/M (from 6.28 +/- 1.55% to 11.18 +/- 1.73%, p Conclusion Calcium phosphate nanoparticles interfered with cell cycle of cultured human ovarian granulosa cells thus increasing cell apoptosis. This pilot study suggested that effects of nanoparticles on ovarian function should be extensively investigated.

  16. Calcium gluconate in phosphate buffered saline increases gene delivery with adenovirus type 5.

    Directory of Open Access Journals (Sweden)

    Marko T Ahonen

    Full Text Available BACKGROUND: Adenoviruses are attractive vectors for gene therapy because of their stability in vivo and the possibility of production at high titers. Despite exciting preclinical data with various approaches, there are only a few examples of clear efficacy in clinical trials. Effective gene delivery to target cells remains the key variable determining efficacy and thus enhanced transduction methods are important. METHODS/RESULTS: We found that heated serum could enhance adenovirus 5 mediated gene delivery up to twentyfold. A new protein-level interaction was found between fiber knob and serum transthyretin, but this was not responsible for the observed effect. Instead, we found that heating caused the calcium and phosphate present in the serum mix to precipitate, and this was responsible for enhanced gene delivery. This finding could have relevance for designing preclinical experiments with adenoviruses, since calcium and phosphate are present in many solutions. To translate this into an approach potentially testable in patients, we used calcium gluconate in phosphate buffered saline, both of which are clinically approved, to increase adenoviral gene transfer up to 300-fold in vitro. Gene transfer was increased with or without heating and in a manner independent from the coxsackie-adenovirus receptor. In vivo, in mouse studies, gene delivery was increased 2-, 110-, 12- and 13-fold to tumors, lungs, heart and liver and did not result in increased pro-inflammatory cytokine induction. Antitumor efficacy of a replication competent virus was also increased significantly. CONCLUSION: In summary, adenoviral gene transfer and antitumor efficacy can be enhanced by calcium gluconate in phosphate buffered saline.

  17. Calcium Gluconate in Phosphate Buffered Saline Increases Gene Delivery with Adenovirus Type 5

    Science.gov (United States)

    Ahonen, Marko T.; Diaconu, Iulia; Pesonen, Sari; Kanerva, Anna; Baumann, Marc; Parviainen, Suvi T.; Spiller, Brad

    2010-01-01

    Background Adenoviruses are attractive vectors for gene therapy because of their stability in vivo and the possibility of production at high titers. Despite exciting preclinical data with various approaches, there are only a few examples of clear efficacy in clinical trials. Effective gene delivery to target cells remains the key variable determining efficacy and thus enhanced transduction methods are important. Methods/Results We found that heated serum could enhance adenovirus 5 mediated gene delivery up to twentyfold. A new protein-level interaction was found between fiber knob and serum transthyretin, but this was not responsible for the observed effect. Instead, we found that heating caused the calcium and phosphate present in the serum mix to precipitate, and this was responsible for enhanced gene delivery. This finding could have relevance for designing preclinical experiments with adenoviruses, since calcium and phosphate are present in many solutions. To translate this into an approach potentially testable in patients, we used calcium gluconate in phosphate buffered saline, both of which are clinically approved, to increase adenoviral gene transfer up to 300-fold in vitro. Gene transfer was increased with or without heating and in a manner independent from the coxsackie-adenovirus receptor. In vivo, in mouse studies, gene delivery was increased 2-, 110-, 12- and 13-fold to tumors, lungs, heart and liver and did not result in increased pro-inflammatory cytokine induction. Antitumor efficacy of a replication competent virus was also increased significantly. Conclusion In summary, adenoviral gene transfer and antitumor efficacy can be enhanced by calcium gluconate in phosphate buffered saline. PMID:20927353

  18. Structural changes to resorbable calcium phosphate bioceramic aged in vitro

    OpenAIRE

    Mehrban, Nazia; Bowen, James; Vorndran, Elke; Gbureck, Uwe; Liam M Grover

    2013-01-01

    This work investigates the effect of mammalian cell culture conditions on 3D printed calcium phosphate scaffolds. The purpose of the studies presented was to characterise the changes in scaffold properties in physiologically relevant conditions. Differences in crystal morphologies were observed between foetal bovine serum-supplemented media and their unsupplemented analogues, but not for supplemented media containing tenocytes. Scaffold porosity was found to increase for all conditions studie...

  19. Functionalized Calcium Phosphates with Anti-Resorptive, Anti-Angiogenetic and Anti-Bacteric Properties

    OpenAIRE

    Forte, Lucia

    2017-01-01

    This PhD thesis was addressed to study the interaction between calcium phosphates and several functionalizing agents, in order to develop new materials with enhanced biological performance, suitable for biomedical applications in the orthopedic field. The functionalizing molecules taken into consideration include several bisphosphonates, namely risedronate, zoledronate, and alendronate, and a molecule from the large group of flavonoids, quercetin (3, 3’, 4’, 5, 7-pentahydroxy-flavone). Functi...

  20. Role of 20-kDa amelogenin (P148) phosphorylation in calcium phosphate formation in vitro.

    Science.gov (United States)

    Kwak, Seo-Young; Wiedemann-Bidlack, Felicitas B; Beniash, Elia; Yamakoshi, Yasuo; Simmer, James P; Litman, Amy; Margolis, Henry C

    2009-07-10

    The potential role of amelogenin phosphorylation in enamel formation is elucidated through in vitro mineralization studies. Studies focused on the native 20-kDa porcine amelogenin proteolytic cleavage product P148 that is prominent in developing enamel. Experimental conditions supported spontaneous calcium phosphate precipitation with the initial formation of amorphous calcium phosphate (ACP). In the absence of protein, ACP was found to undergo relatively rapid transformation to randomly oriented plate-like apatitic crystals. In the presence of non-phosphorylated recombinant full-length amelogenin, rP172, a longer induction period was observed during which relatively small ACP nanoparticles were transiently stabilized. In the presence of rP172, these nanoparticles were found to align to form linear needle-like particles that subsequently transformed and organized into parallel arrays of apatitic needle-like crystals. In sharp contrast to these findings, P148, with a single phosphate group on serine 16, was found to inhibit calcium phosphate precipitation and stabilize ACP formation for more than 1 day. Additional studies using non-phosphorylated recombinant (rP147) and partially dephosphorylated forms of P148 (dephoso-P148) showed that the single phosphate group in P148 was responsible for the profound effect on mineral formation in vitro. The present study has provided, for the first time, evidence suggesting that the native proteolytic cleavage product P148 may have an important functional role in regulating mineralization during enamel formation by preventing unwanted mineral formation within the enamel matrix during the secretory stage of amelogenesis. Results obtained have also provided new insights into the functional role of the highly conserved hydrophilic C terminus found in full-length amelogenin.

  1. Formation of calcium phosphates by vapour diffusion in highly concentrated ionic micro-droplets

    Energy Technology Data Exchange (ETDEWEB)

    Iafisco, M. [Alma Mater Studiorum Universita di Bologna, Dipartimento di Chimica ' ' G. Ciamician' ' , Via Selmi 2, 40126 Bologna (Italy); Universita del Piemonte Orientale, Dipartimento di Scienze Mediche, Via Solaroli 4, 28100 Novara (Italy); Delgado-Lopez, J.M.; Gomez-Morales, J.; Hernandez-Hernandez, M.A.; Rodriguez-Ruiz, I. [Laboratorio de Estudios Cristalograficos, IACT CSIC-UGR, Edificio Lopez Neyra, Avenida del Conocimiento, s/n 18100 Armilla (Spain); Roveri, N. [Alma Mater Studiorum Universita di Bologna, Dipartimento di Chimica ' ' G. Ciamician' ' , Via Selmi 2, 40126 Bologna (Italy)

    2011-08-15

    In this work we have used the sitting drop vapour diffusion technique, employing the ''crystallization mushroom '' to analyze the evolution of calcium phosphate crystallization in micro-droplets containing high initial concentrations of Ca{sup 2+} and HPO{sub 4}{sup 2-}. The decomposition of NH{sub 4}HCO{sub 3} solution produces vapours of NH{sub 3} and CO{sub 2} which diffuse through the droplets containing an aqueous solution of Ca(CH{sub 3}COO){sub 2} and (NH{sub 4}){sub 2}HPO{sub 4}. The result is the increase of pH by means of the diffusion of NH{sub 3} gas and the doping of the calcium phosphate with CO{sub 3}{sup 2-} ions by means of the diffusion of CO{sub 2} gas. The pH of the crystallization process is monitored and the precipitates at different times are characterized by XRD, FTIR, TGA, SEM and TEM techniques. The slow increase of pH and the high concentration of Ca{sup 2+} and HPO{sub 4}{sup 2-} in the droplets induce the crystallization of three calcium phosphate phases: dicalcium phosphate dihydrate (DCPD, brushite), octacalcium phosphate (OCP) and carbonate-hydroxyapatite (HA). The amount of HA nanocrystals with needle-like morphology and dimensions of about 100 nm, closely resembling the inorganic phase of bones, gradually increases, with the precipitation time up to 7 days, whereas the amount of DCPD, growing along the b axis, increases up to 3 days. Then, DCDP crystals start to hydrolyze yielding OCP nanoribbons and HA nanocrystals. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  2. External bone remodeling after injectable calcium-phosphate cement in benign bone tumor: two cases in the hand.

    Science.gov (United States)

    Ichihara, S; Vaiss, L; Acciaro, A L; Facca, S; Liverneaux, P

    2015-12-01

    Bone remodeling commonly occurred after fracture and curettage benign bone tumor. A lot of previous articles reported "internal" trabecular bone remodeling. There were no previous clinical reports about "external" cortical bone remodeling. We present here 2 clinical cases of "external" bone remodeling after injectable calcium-phosphate in benign bone tumor in the hand. In two cases of benign bone tumor, we performed complete removal of the tumor and immediate filling of the metacarpal bone with injectable calcium-phosphate cement Arexbone(®) from the mechanical viewpoint. With respect to the shape of the calcium-phosphate, by using an injection-type, calcium-phosphate is adhered uniformly to the bone cortex by injecting, remodeling has been promoted. After 5 and 8years, both cases were no recurrences, and the shape of the metacarpal looked close to the contralateral side. These findings supposed to be concerned with potential self-healing and self-protection mechanism in human body.

  3. An in vitro comparison of casein phosphopeptide-amorphous calcium phosphate paste, casein phosphopeptide-amorphous calcium phosphate paste with fluoride and casein phosphopeptide-amorphous calcium phosphate varnish on the inhibition of demineralization and promotion of remineralization of enamel

    Directory of Open Access Journals (Sweden)

    Prachi Jayesh Thakkar

    2017-01-01

    Full Text Available Aim: This study aims to determine and compare the extent of inhibition of demineralization and promotion of remineralization of permanent molar enamel with and without application of three remineralizing agents. Materials and Methods: Forty extracted permanent molars were randomly divided into two groups 1 and 2, longitudinally sectioned into four and divided into subgroups A, B, C, and D. The sections were coated with nail varnish leaving a window of 3 mm × 3 mm. All sections of Group 1 were treated with their respective subgroup-specific agent: Casein phosphopeptide-amorphous calcium phosphate (CPP-ACP paste for subgroup A, CPP-amorphous calcium phosphate fluoride (ACPF paste for subgroup B, CPP-ACPF varnish for subgroup C and subgroup D served as a control. The sections were then subjected to demineralization for 12 days following which lesional depth was measured under the stereomicroscope. All the sections of Group 2 were subjected to demineralization for 12 days, examined for lesional depth, then treated with their respective subgroup specific agents and immersed in artificial saliva for 7 days. The sections were then examined again under the stereomicroscope to measure the lesional depth. Results: CPP-ACPF varnish caused significant inhibition of demineralization. All three agents showed significant remineralization of previously demineralized lesions. However, CPP-ACPF varnish showed the greatest remineralization, followed by CPP-ACPF paste and then CPP-ACP paste. Conclusion: This study shows that CPP-ACPF varnish is effective in preventing demineralization as well as promoting remineralization of enamel. Thus, it can be used as an effective preventive measure for pediatric patients where compliance with the use of tooth mousse may be questionable.

  4. Performance of functionally graded implants of polylactides and calcium phosphate/calcium carbonate in an ovine model for computer assisted craniectomy and cranioplasty.

    Science.gov (United States)

    Eufinger, Harald; Rasche, Christian; Lehmbrock, Jutta; Wehmöller, Michael; Weihe, Stephan; Schmitz, Inge; Schiller, Carsten; Epple, Matthias

    2007-01-01

    Biodegradable functionally graded skull implants on the basis of polylactides and calcium phosphate/calcium carbonate were prepared in an individual mould using a combination of different processing techniques. A geometrically corresponding resection template was designed to enable a craniectomy and cranioplasty with the prepared implant in the same operation. After various preliminary experiments concerning degradation kinetics, pH evolution during degradation, micromorphology, biocompatibility tests in human osteoblast cell cultures and surgery of cadaver heads, a new large-animal model was developed for long-term in vivo studies. In eight 12-months-old sheep, the surgical templates were used to create 4.5 x 5 cm(2) calvarial defects which were then filled with the corresponding degradable implants in the same operation. The animals were sacrificed after 2, 9, 12 and 18 months, and the implants and the surrounding tissues were analysed by computer tomography (CT), macroscopic examination and microscopy. The new animal model proved to be reliable and very suitable for large individual craniectomies and cranioplasties. The formation of new bone from the dural layer of the meninges corresponded well to the degradation of the porous inner layer of the implants whereas the skull contour was stabilised by the compact outer layer over the follow-up period.

  5. Cell response of calcium phosphate based ceramics, a bone substitute material

    Directory of Open Access Journals (Sweden)

    Juliana Marchi

    2013-01-01

    Full Text Available The aim of this study was to characterize calcium phosphate ceramics with different Ca/P ratios and evaluate cell response of these materials for use as a bone substitute. Bioceramics consisting of mixtures of hydroxyapatite (HAp and β-tricalcium phosphate (β-TCP powders in different proportions were pressed and sintered. The physical and chemical properties of these bioceramics were then characterized. Characterization of the biological properties of these materials was based on analysis of cell response using cultured fibroblasts. The number of cells attached to the samples was counted from SEM images of samples exposed to cell culture solution for different periods. These data were compared by analysis of variance (ANOVA complemented by the Tukey's test. The TCP sample had higher surface roughness and lower density. The adherence and growth of FMM1 cells on samples from all groups was studied. Even though the different calcium based ceramics exhibited properties which made them suitable as bone substitutes, those with higher levels of β-TCP revealed improved cell growth on their surfaces. These observations indicated two-phase calcium phosphate based materials with a β-TCP surface layer to be a promising bone substitute.

  6. 3D Printing of Composite Calcium Phosphate and Collagen Scaffolds for Bone Regeneration

    Science.gov (United States)

    Inzana, Jason A.; Olvera, Diana; Fuller, Seth M.; Kelly, James P.; Graeve, Olivia A.; Schwarz, Edward M.; Kates, Stephen L.; Awad, Hani A.

    2014-01-01

    Low temperature 3D printing of calcium phosphate scaffolds holds great promise for fabricating synthetic bone graft substitutes with enhanced performance over traditional techniques. Many design parameters, such as the binder solution properties, have yet to be optimized to ensure maximal biocompatibility and osteoconductivity with sufficient mechanical properties. This study tailored the phosphoric acid-based binder solution concentration to 8.75 wt% to maximize cytocompatibility and mechanical strength, with a supplementation of Tween 80 to improve printing. To further enhance the formulation, collagen was dissolved into the binder solution to fabricate collagen-calcium phosphate composites. Reducing the viscosity and surface tension through a physiologic heat treatment and Tween 80, respectively, enabled reliable thermal inkjet printing of the collagen solutions. Supplementing the binder solution with 1–2 wt% collagen significantly improved maximum flexural strength and cell viability. To assess the bone healing performance, we implanted 3D printed scaffolds into a critically sized murine femoral defect for 9 weeks. The implants were confirmed to be osteoconductive, with new bone growth incorporating the degrading scaffold materials. In conclusion, this study demonstrates optimization of material parameters for 3D printed calcium phosphate scaffolds and enhancement of material properties by volumetric collagen incorporation via inkjet printing. PMID:24529628

  7. Influence of polymeric additives on the cohesion and mechanical properties of calcium phosphate cements.

    Science.gov (United States)

    An, Jie; Wolke, Joop G C; Jansen, John A; Leeuwenburgh, Sander C G

    2016-03-01

    To expand the clinical applicability of calcium phosphate cements (CPCs) to load-bearing anatomical sites, the mechanical and setting properties of CPCs need to be improved. Specifically, organic additives need to be developed that can overcome the disintegration and brittleness of CPCs. Hence, we compared two conventional polymeric additives (i.e. carboxylmethylcellulose (CMC) and hyaluronan (HA)) with a novel organic additive that was designed to bind to calcium phosphate, i.e. hyaluronan-bisphosphonate (HABP). The unmodified cement used in this study consisted of a powder phase of α-tricalcium phosphate (α-TCP) and liquid phase of 4% NaH2PO4·2H2O, while the modified cements were fabricated by adding 0.75 or 1.5 wt% of the polymeric additive to the cement. The cohesion of α-TCP was improved considerably by the addition of CMC and HABP. None of the additives improved the compression and bending strength of the cements, but the addition of 0.75% HABP resulted into a significantly increased cement toughness as compared to the other experimental groups. The stimulatory effects of HABP on the cohesion and toughness of the cements is hypothesized to derive from the strong affinity between the polymer-grafted bisphosphonate ligands and the calcium ions in the cement matrix.

  8. Development of a Calcium Phosphate Nanocomposite for Fast Fluorogenic Detection of Bacteria

    Directory of Open Access Journals (Sweden)

    Claudio R. Martínez

    2014-09-01

    Full Text Available Current procedures for the detection and identification of bacterial infections are laborious, time-consuming, and require a high workload and well-equipped laboratories. Therefore the work presented herein developed a simple, fast, and low cost method for bacterial detection based on hydroxyapatite nanoparticles with a nutritive mixture and the fluorogenic substrate. Calcium phosphate ceramic nanoparticles were characterized and integrated with a nutritive mixture for the early detection of bacteria by visual as well as fluorescence spectroscopy techniques. The composite was obtained by combining calcium phosphate nanoparticles (Ca:P ratio, 1.33:1 with a nutritive mixture of protein hydrolysates and carbon sources, which promote fast bacterial multiplication, and the fluorogenic substrate 4-methylumbellipheryl-β-d-glucuronide (MUG. The composite had an average particle size of 173.2 nm and did not show antibacterial activity against Gram-negative or Gram-positive bacteria. After an Escherichia coli suspension was in contact with the composite for 60–90 min, fluorescence detected under UV light or by fluorescence spectrophotometer indicated the presence of bacteria. Intense fluorescence was observed after incubation for a maximum of 90 min. Thus, this calcium phosphate nanocomposite system may be useful as a model for the development of other nanoparticle composites for detection of early bacterial adhesion.

  9. The effect of porosity on drug release kinetics from vancomycin microsphere/calcium phosphate cement composites.

    Science.gov (United States)

    Schnieders, Julia; Gbureck, Uwe; Vorndran, Elke; Schossig, Michael; Kissel, Thomas

    2011-11-01

    The influence of porosity on release profiles of antibiotics from calcium phosphate composites was investigated to optimize the duration of treatment. We hypothesized, that by the encapsulation of vancomycin-HCl into biodegradable microspheres prior admixing to calcium phosphate bone cement, the influence of porosity of the cement matrix on vancomycin release could be reduced. Encapsulation of vancomycin into a biodegradable poly(lactic co-glycolic acid) copolymer (PLGA) was performed by spray drying; drug-loaded microparticles were added to calcium phosphate cement (CPC) at different powder to liquid ratios (P/L), resulting in different porosities of the cement composites. The effect of differences in P/L ratio on drug release kinetics was compared for both the direct addition of vancomycin-HCl to the cement liquid and for cement composites modified with vancomycin-HCl-loaded microspheres. Scanning electron microscopy (SEM) was used to visualize surface and cross section morphology of the different composites. Brunauer, Emmett, and Teller-plots (BET) was used to determine the specific surface area and pore size distribution of these matrices. It could be clearly shown, that variations in P/L ratio influenced both the porosity of cement and vancomycin release profiles. Antibiotic activity during release study was successfully measured using an agar diffusion assay. However, vancomycin-HCl encapsulation into PLGA polymer microspheres decreased porosity influence of cement on drug release while maintaining antibiotic activity of the embedded substance.

  10. Orbital floor reconstruction using calcium phosphate cement paste: an animal study.

    Science.gov (United States)

    Tañag, Marvin A; Yano, Kenji; Hosokawa, Ko

    2004-12-01

    Orbital floor defects were created in 10 New Zealand white rabbits and were reconstructed using an injectable calcium phosphate paste. These animals were euthanized at 2, 4, 8, and 12 months after implantation and were examined for biocompatibility and osteoconductivity. Grossly, implants were found to be adherent to the floor and covered with fibrous tissues. There was no sign of infection, extrusion, or migration of implant within the orbit and maxilla. The orbital floor was completely restored. Histological examination showed active new bone formation that encroached within the implant and gradually increased in density with time. Maxillary mucosa and glands were likewise reconstituted. Thin fibrovascular tissues were seen on top of and within the surface of the implant, and few to slight inflammatory cells were seen. Microradiography showed direct apposition between the new bone and the implant. These findings compare favorably with previously published reports on the biocompatibility and osteoconductivity of calcium phosphate cement. The authors believe that, together with ease of use and structural integrity, calcium phosphate paste can be useful in orbital floor reconstruction.

  11. Designing calcium phosphate-based bifunctional nanocapsules with bone-targeting properties

    Energy Technology Data Exchange (ETDEWEB)

    Khung, Yit-Lung; Bastari, Kelsen; Cho, Xing Ling; Yee, Wu Aik; Loo, Say Chye Joachim, E-mail: joachimloo@ntu.edu.sg [Nanyang Technological University, School of Materials Science and Engineering (Singapore)

    2012-06-15

    Using sodium dodecyl sulphate micelles as template, hollow-cored calcium phosphate nanocapsules were produced. The surfaces of the nanocapsule were subsequently silanised by a polyethylene glycol (PEG)-based silane with an N-hydroxysuccinimide ester end groups which permits for further attachment with bisphosphonates (BP). Characterisations of these nanocapsules were investigated using Field Emission Scanning Electron Microscopy (FESEM), Transmission Electron Microscopy, Fourier Transform Infra-Red Spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy and Dynamic Light Scattering. To further validate the bone-targeting potential, dentine discs were incubated with these functionalised nanocapsules. FESEM analysis showed that these surface-modified nanocapsules would bind strongly to dentine surfaces compared to non-functionalised nanocapsules. We envisage that respective components would give this construct a bifunctional attribute, whereby (1) the shell of the calcium phosphate nanocapsule would serve as biocompatible coating aiding in gradual osteoconduction, while (2) surface BP moieties, acting as targeting ligands, would provide the bone-targeting potential of these calcium phosphate nanocapsules.

  12. Does Salivary Calcium and Phosphate Concentrations Adequately Reflect Bone Mineral Density in Patients with Chronic Periodontitis?

    Science.gov (United States)

    Moghadam, Somaye Ansari; Zakeri, Zahra; Fakour, Sirous Risbaf; Moghaddam, Alireza Ansari

    2016-10-01

    Periodontitis is the inflammation of the periodontal supporting tissues. The response of periodontal tissues to local bacteria leads to bone resorption and destruction of periodontal junction. Given the possible association between periodontitis and low bone mineral density, the aim of present study was to find if measurement of salivary biomarkers as a less invasive method, can provide an appropriate screening method for assessment of bone mineral density in patients with chronic periodontitis? A case-control study was conducted on 53 people, including 28 patients with severe chronic periodontitis and 25 healthy people between April 2014 to March 2015 in Zahedan (southeast of Iran). Following Periodontal examination, salivary samples were collected, and the concentration of salivary calcium and phosphate were measured and reported as mg/dl. Bone mineral density of participants was measured using dual energy x-ray absorptiometry and reported as gr/cm2. No significant association was found between concentrations of salivary calcium and phosphate levels with bone mineral density in either healthy people or in patients with severe chronic periodontitis, despite a significant bone density reduction (in the femur neck and lumbar spine L2-L4) in the periodontitis group compared to healthy people (P=0.006, and P=0.009 respectively). Concentration of salivary calcium and phosphate do not appear to be good indicators of bone mineral density. Further prospective studies with larger sample size are recommended.

  13. 3D printing of composite calcium phosphate and collagen scaffolds for bone regeneration.

    Science.gov (United States)

    Inzana, Jason A; Olvera, Diana; Fuller, Seth M; Kelly, James P; Graeve, Olivia A; Schwarz, Edward M; Kates, Stephen L; Awad, Hani A

    2014-04-01

    Low temperature 3D printing of calcium phosphate scaffolds holds great promise for fabricating synthetic bone graft substitutes with enhanced performance over traditional techniques. Many design parameters, such as the binder solution properties, have yet to be optimized to ensure maximal biocompatibility and osteoconductivity with sufficient mechanical properties. This study tailored the phosphoric acid-based binder solution concentration to 8.75 wt% to maximize cytocompatibility and mechanical strength, with a supplementation of Tween 80 to improve printing. To further enhance the formulation, collagen was dissolved into the binder solution to fabricate collagen-calcium phosphate composites. Reducing the viscosity and surface tension through a physiologic heat treatment and Tween 80, respectively, enabled reliable thermal inkjet printing of the collagen solutions. Supplementing the binder solution with 1-2 wt% collagen significantly improved maximum flexural strength and cell viability. To assess the bone healing performance, we implanted 3D printed scaffolds into a critically sized murine femoral defect for 9 weeks. The implants were confirmed to be osteoconductive, with new bone growth incorporating the degrading scaffold materials. In conclusion, this study demonstrates optimization of material parameters for 3D printed calcium phosphate scaffolds and enhancement of material properties by volumetric collagen incorporation via inkjet printing.

  14. Elaboration de biocéramiques phosphocalciques Processing of calcium phosphate bioceramics

    Directory of Open Access Journals (Sweden)

    Champion Eric

    2013-11-01

    Full Text Available Les céramiques phosphocalciques (hydroxyapatite, phosphate tricalcique sont couramment utilisées comme implants synthétiques en substitution osseuse. Le développement de nouveaux implants céramiques aux performances accrues nécessite la maîtrise de nombreux paramètres chimiques et physiques intervenant dans leurs procédés d'élaboration : synthèse de poudres spécifiques, mise en forme d'architectures complexes contrôlées, frittage et fonctionnalisation. Cette contribution illustre à travers quelques exemples les travaux menés dans le domaine des procédés d'élaboration de ces biocéramiques phosphocalciques pour des applications en ingénierie des tissus osseux. Calcium phosphate ceramics (hydroxyapatite, tricalcium phosphate are commonly used as synthetic bone graft substitutes. The development of new ceramic implants with improved performances requires the mastering of many chemical and physical parameters involved in their processing: synthesis of specific powders, shaping of complex architectures, sintering and functionalization. This paper illustrates a few examples of the work in the field of processes of these calcium phosphate bioceramics for applications in bone tissue engineering.

  15. Incorporation of a controlled-release glass into a calcium phosphate cement.

    Science.gov (United States)

    Khairoun, I; Boltong, M G; Gil, F J; Driessens, F C; Planell, J A; Seijas, M M; Martínez, S

    1999-04-01

    A so-called controlled-release glass was synthesized occurring in the system CaO-Na2O-P2O5. A certain sieve fraction of this glass was incorporated in a calcium phosphate cement, of which the powder contained alpha-tricalcium phosphate (alpha-TCP), dicalcium phosphate (DCP) and precipitated hydroxyapatite (HA). The glass appeared to retard the cement setting slightly and it reduced considerably the compressive strength after aging in aqueous solutions which were continuously refreshed. Scanning electron microscope (SEM) pictures and X-ray diffraction (XRD) patterns of the samples after 5 weeks of aging showed that the glass was not dissolved but that large brushite crystals were formed. Thereby, aging in CaCl2 solutions resulted in more brushite formation than aging in NaCl solutions. The brushite crystals did not reinforce the cement. Neither was the aged glass-containing cement weaker than it was before the brushite formation right after complete setting. In conclusion, the incorporation of controlled-release glasses into a calcium phosphate cement and subsequent aging in aqueous solutions did not result in the formation of macropores in the cement structure, but that of brushite crystals. This incorporation reduced the compressive strength of the cement considerably.

  16. Effectiveness of nano-calcium phosphate paste on sensitivity during and after bleaching: a randomized clinical trial

    OpenAIRE

    LOGUERCIO, Alessandro Dourado; Lidia Yileng TAY; HERRERA,Daniel Rodrigo; Bauer,Jose; Reis, Alessandra

    2015-01-01

    The study aimed to evaluate the effectiveness of in-office bleaching and associated tooth sensitivity on application of nano-calcium phosphate paste as desensitizing agent. Bleaching was performed with 35% hydrogen peroxide gel in 40 patients who were randomly divided into placebo and nano-calcium phosphate paste groups. Bleaching efficacy (BE) was evaluated using a value-oriented Vita shade guide. Tooth sensitivity was recorded using a numeric rating scale (0–4) during bleaching and up...

  17. Calcium Phosphate Crystals from Uremic Serum Promote Osteogenic Differentiation in Human Aortic Smooth Muscle Cells.

    Science.gov (United States)

    Liu, Yaorong; Zhang, Lin; Ni, Zhaohui; Qian, Jiaqi; Fang, Wei

    2016-11-01

    Recent study demonstrated that calcium phosphate (CaP) crystals isolated from high phosphate medium were a key contributor to arterial calcification. The present study further investigated the effects of CaP crystals induced by uremic serum on calcification of human aortic smooth muscle cells. This may provide a new insight for the development of uremic cardiovascular calcification. We tested the effects of uremic serum or normal serum on cell calcification. Calcification was visualized by staining and calcium deposition quantified. Expression of various bone-calcifying genes was detected by real-time PCR, and protein levels were quantified by western blotting or enzyme-linked immunosorbent assays. Pyrophosphate was used to investigate the effects of CaP crystals' inhibition. Finally, CaP crystals were separated from uremic serum to determine its specific pro-calcification effects. Uremic serum incubation resulted in progressively increased calcification staining and increased calcium deposition in HASMCs after 4, 8 and 12 days (P vs 0 day crystals with pyrophosphate incubation prevented calcium deposition and bone-calcifying gene over-expression increased by uremic serum. CaP crystals, rather than the rest of uremic serum, were responsible for these effects. Uremic serum accelerates arterial calcification by mediating osteogenic differentiation. This effect might be mainly attributed to the CaP crystal content.

  18. Identification of the hydrate gel phases present in phosphate-modified calcium aluminate binders

    Energy Technology Data Exchange (ETDEWEB)

    Chavda, Mehul A.; Bernal, Susan A. [Department of Materials Science and Engineering, The University of Sheffield, Sheffield S1 3JD (United Kingdom); Apperley, David C. [Solid-State NMR Group, Department of Chemistry, Durham University, Durham DH1 3LE (United Kingdom); Kinoshita, Hajime [Department of Materials Science and Engineering, The University of Sheffield, Sheffield S1 3JD (United Kingdom); Provis, John L., E-mail: j.provis@sheffield.ac.uk [Department of Materials Science and Engineering, The University of Sheffield, Sheffield S1 3JD (United Kingdom)

    2015-04-15

    The conversion of hexagonal calcium aluminate hydrates to cubic phases in hydrated calcium aluminate cements (CAC) can involve undesirable porosity changes and loss of strength. Modification of CAC by phosphate addition avoids conversion, by altering the nature of the reaction products, yielding a stable amorphous gel instead of the usual crystalline hydrate products. Here, details of the environments of aluminium and phosphorus in this gel were elucidated using solid-state NMR and complementary techniques. Aluminium is identified in both octahedral and tetrahedral coordination states, and phosphorus is present in hydrous environments with varying, but mostly low, degrees of crosslinking. A {sup 31}P/{sup 27}Al rotational echo adiabatic passage double resonance (REAPDOR) experiment showed the existence of aluminium–phosphorus interactions, confirming the formation of a hydrated calcium aluminophosphate gel as a key component of the binding phase. This resolves previous disagreements in the literature regarding the nature of the disordered products forming in this system.

  19. Effect of poly(aspartic acid) on calcium phosphate removal from stainless steel tubing under turbulent flow conditions

    Science.gov (United States)

    Littlejohn, Felicia

    Calcium phosphate deposition causes cleaning problems in a number of situations including water treatment, dairy processing, and dental applications. This problem is exacerbated by the limited choices of cleaning chemicals that meet environmental regulations. To promote the development of biodegradable, non-toxic alternatives, this research examines the removal of calcium phosphate deposits consisting of brushite (dicalcium phosphate dihydrate; DCPD) and a mixture of hydroxyapatite (HAP) and DCPD from stainless steel in the presence of poly(aspartic acid) and its sodium salt (PASP). The effects of solvent pH, PASP concentration, and flow rate on the calcium phosphate removal rates are measured from stainless steel tubing under turbulent flow conditions using a solid scintillation detection technique. A mechanistic evaluation of the cleaning data in the absence of PASP indicates that DCPD removal is dominated by shear while HAP/DCPD deposit removal is limited by a combination of mass transfer and interfacial processes. Although the removal mechanisms differ, the results conclusively show that PASP promotes calcium phosphate removal under conditions that favor calcium sequestration in both cases. An in-depth study of DCPD removal in the presence of PASP reveals that this additive is most effective under conditions where calcium sequestration and phosphate protonation occur simultaneously.

  20. A new iron calcium phosphate material to improve the osteoconductive properties of a biodegradable ceramic: a study in rabbit calvaria.

    Science.gov (United States)

    Manchón, Angel; Hamdan Alkhraisat, Mohammad; Rueda-Rodriguez, Carmen; Prados-Frutos, Juan Carlos; Torres, Jesús; Lucas-Aparicio, Julia; Ewald, Andrea; Gbureck, Uwe; López-Cabarcos, Enrique

    2015-10-20

    β-tricalcium phosphate (β-TCP) is an osteoconductive and biodegradable material used in bone regeneration procedures, while iron has been suggested as a tool to improve the biological performance of calcium phosphate-based materials. However, the mechanisms of interaction between these materials and human cells are not fully understood. In order to clarify this relationship, we have studied the iron role in β-TCP ceramics. Iron-containing β-TCPs were prepared by replacing CaCO3 with C6H5FeO7 at different molar ratios. X-ray diffraction analysis indicated the occurrence of β-TCP as the sole phase in the pure β-TCP and iron-containing ceramics. The incorporation of iron ions in the β-TCP lattice decreased the specific surface area as the pore size was shifted toward meso- and/or macropores. Furthermore, the human osteoblastlike cell line MG-63 was cultured onto the ceramics to determine cell proliferation and viability, and it was observed that the iron-β-TCP ceramics have better cytocompatibility than pure β-TCP. Finally, in vivo assays were performed using rabbit calvaria as a bone model. The scaffolds were implanted for 8 and 12 weeks in the defects created in the skullcap with pure β-TCP as the control. The in vivo behavior, in terms of new bone formed, degradation, and residual graft material were investigated using sequential histological evaluations and histomorphometric analysis. The in vivo implantation of the ceramics showed enhanced bone tissue formation and scaffold degradation for iron-β-TCPs. Thus, iron appears to be a useful tool to enhance the osteoconductive properties of calcium phosphate ceramics.

  1. Effect of pyrophosphate ions on the conversion of calcium-lithium-borate glass to hydroxyapatite in aqueous phosphate solution.

    Science.gov (United States)

    Fu, Hailuo; Rahaman, Mohamed N; Day, Delbert E; Huang, Wenhai

    2010-10-01

    The conversion of glass to a hydroxyapatite (HA) material in an aqueous phosphate solution is used as an indication of the bioactive potential of the glass, as well as a low temperature route for preparing biologically useful materials. In this work, the effect of varying concentrations of pyrophosphate ions in the phosphate solution on the conversion of a calcium-lithium-borate glass to HA was investigated. Particles of the glass (150-355 μm) were immersed for up to 28 days in 0.25 M K(2)HPO(4) solution containing 0-0.1 M K(4)P(2)O(7). The kinetics of degradation of the glass particles and their conversion to HA were monitored by measuring the weight loss of the particles and the ionic concentration of the solution. The structure and composition of the conversion products were analyzed using X-ray diffraction, scanning electron microscopy, and Fourier transform infrared spectroscopy. For K(4)P(2)O(7) concentrations of up to 0.01 M, the glass particles converted to HA, but the time for complete conversion increased from 2 days (no K(4)P(2)O(7)) to 10 days (0.01 M K(4)P(2)O(7)). When the K(4)P(2)O(7) concentration was increased to 0.1 M, the product consisted of an amorphous calcium phosphate material, which eventually crystallized to a pyrophosphate product (predominantly K(2)CaP(2)O(7) and Ca(2)P(2)O(7)). The consequences of the results for the formation of HA materials and devices by the glass conversion route are discussed.

  2. Electrospun gelatin/poly(ε-caprolactone) fibrous scaffold modified with calcium phosphate for bone tissue engineering

    Energy Technology Data Exchange (ETDEWEB)

    Rajzer, Izabella, E-mail: irajzer@ath.bielsko.pl [University of Bielsko-Biala (ATH), Department of Mechanical Engineering Fundamentals, Division of Materials Engineering, Willowa 2 Street, 43-309 Bielsko-Biała (Poland); Menaszek, Elżbieta [Jagiellonian University (UJ), Collegium Medicum, Department of Cytobiology, Medyczna 9 Street, 30-068 Cracow (Poland); Kwiatkowski, Ryszard [University of Bielsko-Biala (ATH), Faculty of Materials and Environmental Sciences, Institute of Textile Engineering and Polymer Materials, Willowa 2 Street, 43-309 Bielsko-Biała (Poland); Planell, Josep A.; Castano, Oscar [Institute for Bioengineering of Catalonia (IBEC), Biomaterials for Regenerative Therapies, Baldiri Reixac 15-21, 08028 Barcelona (Spain); Polytechnic University of Catalonia (UPC), Diagonal 647, 08028 Barcelona (Spain); CIBER-BBN The Biomedical Research Networking Center in Bioengineering, Biomaterials and Nanomedicine, Barcelona (Spain)

    2014-11-01

    In this study gelatin (Gel) modified with calcium phosphate nanoparticles (SG5) and polycaprolactone (PCL) were used to prepare a 3D bi-layer scaffold by collecting electrospun PCL and gelatin/SG5 fibers separately in the same collector. The objective of this study was to combine the desired properties of PCL and Gel/SG5 in the same scaffold in order to enhance mineralization, thus improving the ability of the scaffold to bond to the bone tissue. The scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and the wide angle X-ray diffraction (WAXD) measurements confirmed that SG5 nanoparticles were successfully incorporated into the fibrous gelatin matrix. The composite Gel/SG5/PCL scaffold exhibited more enhanced mechanical properties than individual Gel and Gel/SG5 scaffolds. The presence of SG5 nanoparticles accelerated the nucleation and growth of apatite crystals on the surface of the composite Gel/SG5/PCL scaffold in simulated body fluid (SBF). The osteoblast response in vitro to developed electrospun scaffolds (PCL and Gel/SG5/PCL) was investigated by using normal human primary NHOst cell lines. NHOst cell culture studies showed that higher alkaline phosphatase (ALP) activity and better mineralization were obtained in the case of composite materials than in pure PCL scaffolds. The mechanically strong PCL scaffold served as a skeleton, while the Gel/SG5 fibers facilitated cell spreading and mineralization of the scaffold. - Highlights: • Bi-layer scaffolds were produced by electrospinning method. • The addition of nanoparticles enhanced the bioactivity of scaffold. • Bi-layer scaffold enhanced ALP activity and NHOst cell mineralization.

  3. In vivo resorption behavior of a high strength injectable calcium-phosphate cement

    Energy Technology Data Exchange (ETDEWEB)

    Wolke, J.G.C.; Ooms, E.M.; Jansen, J.A. [Univ. Medical Center, Nijmegen (Netherlands). Dept. Biomaterials

    2001-07-01

    A high strength calcium-phosphate-cement powder was prepared from a composition comprising of {alpha}-TCP, CaHPO{sub 4} (monetite), CaCO{sub 3} and some seeds of precipitated apatite. An aqueous solution of 4% Na{sub 2}HPO{sub 4} was used as liquid to start the setting reaction. The powder was mixed with cement liquid in three different liquid/powder ratios respectively 0.3, 0.35 and 0.4. Observation of the setting reaction versus time revealed that the maximum of compressive strength was achieved after 3 days reaching the value of 81 MPa. The X-ray diffraction pattern of the Ca-P cement measured 3 days after mixing and storage in Ringer's solution at 37 C showed that the {alpha}-TCP was transformed to hydroxylapatite with superposition of the peaks for monetite. XRD showed that after eight weeks of implantation the monetite peaks had disappeared. Further, the clinical handling properties of all three types of Ca-P cement appeared to be excellent. No problems in setting time or cavity filling were met during the application. The histological evaluation after two weeks of implantation showed abundant bone apposition on the cement surface without inflammatory reaction. At later time points the Ca-P cements were totally covered by a thin layer of bone and osteoclast-like cells in remodeling lacunae at the interface were resorbing the cement. At all implantation periods the PMMA controls showed the presence of a thin fibrous membrane. (orig.)

  4. Characterization of nickel-doped biphasic calcium phosphate/graphene nanoplatelet composites for biomedical application.

    Science.gov (United States)

    Baradaran, S; Moghaddam, E; Nasiri-Tabrizi, Bahman; Basirun, W J; Mehrali, M; Sookhakian, M; Hamdi, M; Alias, Y

    2015-04-01

    The effect of the addition of an ionic dopant to calcium phosphates for biomedical applications requires specific research due to the essential roles played in such processes. In the present study, the mechanical and biological properties of Ni-doped hydroxyapatite (HA) and Ni-doped HA mixed with graphene nanoplatelets (GNPs) were evaluated. Ni (3wt.% and 6wt.%)-doped HA was synthesized using a continuous precipitation method and calcined at 900°C for 1h. The GNP (0.5-2wt.%)-reinforced 6% Ni-doped HA (Ni6) composite was prepared using rotary ball milling for 15h. The sintering process was performed using hot isostatic pressing at processing conditions of 1150°C and 160MPa with a 1-h holding time. The results indicated that the phase compositions and structural features of the products were noticeably affected by the Ni and GNPs. The mechanical properties of Ni6 and 1.5Ni6 were increased by 55% and 75% in hardness, 59% and 163% in fracture toughness and 120% and 85% in elastic modulus compared with monolithic HA, respectively. The in-vitro biological behavior was investigated using h-FOB osteoblast cells in 1, 3 and 5days of culture. Based on the osteoblast results, the cytotoxicity of the products was indeed affected by the Ni doping. In addition, the effect of GNPs on the growth and proliferation of osteoblast cells was investigated in Ni6 composites containing different ratios of GNPs, where 1.5wt.% was the optimum value. Copyright © 2015 Elsevier B.V. All rights reserved.

  5. Preparation Calcium Oxide From Chicken Eggshells

    Directory of Open Access Journals (Sweden)

    Risfidian Mohadi

    2016-08-01

    Full Text Available The preparation of metal oxide CaO from chicken eggshell has been carried out by decomposition at various temperatures 600, 700, 800, 900, and 1000oC. The metal oxide CaO was characterized using XRD. Furthermore, The optimum temperature for preparation of CaO was determined based on the XRD pattern, then the characterization of CaO was extended using FT-IR spectrophotometer and BET analysis. The results show that the optimum temperature for preparation of CaO from chicken eggshell is 900oC with peak of 2Ө at 32.3o, 37.4o, 53.9o, 64.2o and 67.5o, respectively. The FT-IR spectrums show the unique vibration for Ca-O at 393 cm-1. The BET analysis show that CaO has surface area 68 m2/g with pore volume 1.65 cm3/g and pore size 6.6 nm which can be classified as mesoporous.

  6. Phase composition, mechanical performance and in vitro biocompatibility of hydraulic setting calcium magnesium phosphate cement.

    Science.gov (United States)

    Klammert, Uwe; Reuther, Tobias; Blank, Melanie; Reske, Isabelle; Barralet, Jake E; Grover, Liam M; Kübler, Alexander C; Gbureck, Uwe

    2010-04-01

    Brushite (CaHPO(4) x 2H(2)O)-forming calcium phosphate cements are of great interest as bone replacement materials because they are resorbable in physiological conditions. However, their short setting times and low mechanical strengths limit broad clinical application. In this study, we showed that a significant improvement of these properties of brushite cement could be achieved by the use of magnesium-substituted beta-tricalcium phosphate with the general formula Mg(x)Ca((3-x))((PO(4))(2) with 0 cement reactants. The incorporation of magnesium ions increased the setting times of cements from 2 min for a magnesium-free matrix to 8-11 min for Mg(2.25)Ca(0.75)(PO(4))(2) as reactant. At the same time, the compressive strength of set cements was doubled from 19 MPa to more than 40 MPa after 24h wet storage. Magnesium ions were not only retarding the setting reaction to brushite but were also forming newberyite (MgHPO(4) x 3H(2)O) as a second setting product. The biocompatibility of the material was investigated in vitro using the osteoblast-like cell line MC3T3-E1. A considerable increase of cell proliferation and expression of alkaline phosphatase, indicating an osteoblastic differentiation, could be noticed. Scanning electron microscopy analysis revealed an obvious cell growth on the surface of the scaffolds. Analysis of the culture medium showed minor alterations of pH value within the physiological range. The concentrations of free calcium, magnesium and phosphate ions were altered markedly due to the chemical solubility of the scaffolds. We conclude that the calcium magnesium phosphate (newberyite) cements have a promising potential for their use as bone replacement material since they provide a suitable biocompatibility, an extended workability and improved mechanical performance compared with brushite cements.

  7. The effects of calcium phosphate particles on the growth of osteoblasts.

    Science.gov (United States)

    Sun, J S; Tsuang, Y H; Liao, C J; Liu, H C; Hang, Y S; Lin, F H

    1997-12-01

    With advances in ceramics technology, calcium phosphate bioceramics have been applied as bone substitutes for several decades. The focus of this work is to elucidate the biocompatibility of the particulates of various calcium phosphate cytotoxicities. Four different kinds of calcium phosphate powders, including beta-tricalcium phosphate (beta-TCP), hydroxyapatite (HA), beta-dicalcium pyrophosphate (beta-DCP), and sintered beta-dicalcium pyrophosphate (SDCP), were tested by osteoblast cell culture. The results were analyzed by cell count, concentration of transforming growth factor-beta 1 (TGF-beta 1), alkaline phosphatase (ALP), and prostaglandin E2 (PGE2) in culture media. The changes were most significant when osteoblasts were cultured with beta-TCP and HA bioceramics. The changes in cell population of the beta-TCP and HA were quite low in the first 3 days, then increased gradually toward the seventh day. The changes in TGF-beta 1 concentration in culture medium inversely related to the changes in cell population. The ALP titer in the culture media of the beta-TCP and HA were quite high in the first 3 days, then decreased rapidly between the third and seventh days. The concentrations of PGE2 in the culture media tested were quite high on the first day, decreased rapidly to the third day, and then gradually until the seventh day. The changes in the beta-DCP and SDCP were quite similar to those of HA and beta-TCP but much less significant. We conclude that HA and beta-TCP have an inhibitory effect on the growth of osteoblasts. The inhibitins effects of the HA and beta-TCP powders on the osteoblast cell cultures possibly are mediated by the increased synthesis of PGE2.

  8. In vitro osteoblast-like and endothelial cells' response to calcium silicate/calcium phosphate cement

    Energy Technology Data Exchange (ETDEWEB)

    Zhao Qinghui; Qian Jiangchao [State Key Laboratory of Bioreactor Engineering, East China University of Science and Technology, Shanghai 200237 (China); Zhou Huanjun; Yuan Yuan; Mao Yuhao; Liu Changsheng, E-mail: jiangchaoqian@ecust.edu.c, E-mail: csliu@sh163.ne [Engineering Research Center for Biomedical Materials of Ministry of Education, East China University of Science and Technology, Shanghai 200237 (China)

    2010-06-01

    This study aims to investigate the interaction between calcium silicate/calcium phosphate cement (CS/CPC) and osteogenesis, in particular the in vitro osteoblast-like and endothelial cells' response to CS/CPC. The effect of CS/CPC on cell attachment, proliferation and differentiation of murine osteoblast-like cell MC3T3-E1, as well as the influence on the cell attachment and proliferation of human umbilical vein endothelial cell (HUVEC), was studied in detail. Our results indicated that CS/CPC exhibited excellent biocompatibility to the osteoblast-like cells. Moreover, the morphology and cytoskeleton organization of MC3T3-E1 cultured on the CS/CPC disks suggested that CS/CPC induced better cell adhesion and cell spreading. Simultaneously, cell proliferation and alkaline phosphatase (ALP) activity of MC3T3-E1 were significantly improved after 3 and 7 days of culture on CS/CPC disks in comparison with CPC disks. Additionally, on CS/CPC disks, HUVEC attached well on day 1 and cell proliferation was also greatly enhanced by day 7. Collectively, these results suggest that the introduction of calcium silicate may improve the cell response involved in the osteogenesis and thus may be beneficial to further modify CPC as a better bone repairing material.

  9. Structural and phase characterization of bioceramics prepared from tetracalcium phosphate-monetite cement and in vitro osteoblast response.

    Science.gov (United States)

    Stulajterova, Radoslava; Medvecky, Lubomir; Giretova, Maria; Sopcak, Tibor

    2015-05-01

    Biphasic porous calcium phosphate ceramics was prepared by sintering of transformed tetracalcium phosphate-monetite cement. After annealing hydroxyapatite, β- or α-TCP were found as main phases in ceramic substrates and a highly microporous microstructure of cement ceramics was created without an addition of porosifier. The origin microstructure features characteristic by the presence of hollow particle agglomerates in cement were preserved in microstructure of cement ceramics after annealing but the hydroxyapatite particles rose in size up to 2 µm and obtained a more regular shape. A small decrease in compressive strength was demonstrated in ceramics sintered up to 1150 °C and enhanced osteoblast proliferation was revealed on cement ceramic substrates in comparison with cement sample and conventional ceramics. The ALP activity of osteoblasts decreased with rise in sintering temperature. The prepared cement microporous ceramics could be utilized as carrier for antibiotics, drugs, growth factors, enzymes or other substances stimulating healing process.

  10. Glucose-6-phosphate reduces calcium accumulation in rat brain endoplasmic reticulum

    Directory of Open Access Journals (Sweden)

    Jeffrey Thomas Cole

    2012-04-01

    Full Text Available Brain cells expend large amounts of energy sequestering calcium (Ca2+, while loss of Ca2+ compartmentalization leads to cell damage or death. Upon cell entry, glucose is converted to glucose-6-phosphate (G6P, a parent substrate to several metabolic major pathways, including glycolysis. In several tissues, G6P alters the ability of the endoplasmic reticulum to sequester Ca2+. This led to the hypothesis that G6P regulates Ca2+ accumulation by acting as an endogenous ligand for sarco-endoplasmic reticulum calcium ATPase (SERCA. Whole brain ER microsomes were pooled from adult male Sprague-Dawley rats. Using radio-isotopic assays, 45Ca2+ accumulation was quantified following incubation with increasing amounts of G6P, in the presence or absence of thapsigargin, a potent SERCA inhibitor. To qualitatively assess SERCA activity, the simultaneous release of inorganic phosphate (Pi coupled with Ca2+ accumulation was quantified. Addition of G6P significantly and decreased Ca2+ accumulation in a dose-dependent fashion (1-10 mM. The reduction in Ca2+ accumulation was not significantly different that seen with addition of thapsigargin. Addition of glucose-1-phosphate or fructose-6-phosphate, or other glucose metabolic pathway intermediates, had no effect on Ca2+ accumulation. Further, the release of Pi was markedly decreased, indicating G6P-mediated SERCA inhibition as the responsible mechanism for reduced Ca2+ uptake. Simultaneous addition of thapsigargin and G6P did decrease inorganic phosphate in comparison to either treatment alone, which suggests that the two treatments have different mechanisms of action. Therefore, G6P may be a novel, endogenous regulator of SERCA activity. Additionally, pathological conditions observed during disease states that disrupt glucose homeostasis, may be attributable to Ca2+ dystasis caused by altered G6P regulation of SERCA activity

  11. Electrodialytic removal of fluoride and calcium ions to recover phosphate from fertilizer industry wastewater

    Directory of Open Access Journals (Sweden)

    Arseto Yekti Bagastyo

    2017-09-01

    Full Text Available The fertilizer industry generates wastewater rich in phosphate and fluoride content, with concentration as high as 4540 and 9720 mg L−1, respectively. The untreated wastewater may enhance the growth of algae, promote eutrophication, and create serious effects on environmental health and aquatic life. Therefore, this wastewater has to be treated before releasing into the environment. This study evaluates the performance of a three-compartment electrodialysis reactor to remove fluoride and calcium ions, and recover phosphate present in the wastewater, for possible further use in the fertilizer industry. The experiments were conducted in a batch system at room temperature. A 4 L of wastewater was electrodialysed using three different electrical current (i.e., 0.5, 0.75, and 1.0 A and two different membrane surface areas (i.e., 100 and 200 cm2. The highest removal of fluoride ions was up to 260 mg L−1 (2.7% by applying 1 A of current and 100 cm2 membrane area. No substantial increase of fluoride and calcium removal was observed for 200 cm2 membrane area. Interestingly, the amount of the remaining phosphate was high (i.e., only 1% removal, implying a very efficient recovery in the feed. The energy required for fluoride ion transfer was much lower than for phosphate ion, i.e., up to 6 vs. 0.12 mol kWh−1, suggesting that a higher removal of fluoride can possibly be achieved by limiting migration of phosphate ion through the membrane.

  12. Calcium Phosphate Coating on Al2 O3 Ceramics by a Biomimetic Method Using Electric Pulse Technique

    Institute of Scientific and Technical Information of China (English)

    JIN Zhengguo; SHI Yong; GUO Wenli; WANG Ying; QIU Jijun

    2005-01-01

    The preparation of calcium phosphate (CP) coating on alumina ceramics using electric pulse stimulating method has been investigated. The cup-shaped alumina ceramics were soaked in a simulated body fluid (SBF), and a square pulse potential with frequency of 1 Hz and voltage of 110 V was applied between the inner and outer surfaces of the alumina cup. Surface morphology of CP coatings during different deposition periods was observed by a Philips XL-30 scanning electron microscope (SEM). Compositional analysis was examined by EDAX. The mechanism of nucleation and growth of CP coating was discussed. SEM result indicates that the coating comprises of a large number of tiny needle-like grains and has a porous microstructure. There is a strong bond between the deposited layer and Al2O3 substrate, which may be due to the gentle growth of the biomimetic method. The EDAX analysis indicates that main composition of the coating is calcium and phosphor. The formation of CP coating may be contributed to the stimulation of electric pulse and the high ions concentration which is 1.5 times of the concentration of SBF solution (1.5SBF solution). Such surface functionalization method by electric pulse potential can be used to prepare CP coating on various electric-insulating bioinert materials for improving their bioactive character.

  13. Preparation and Characterization of a Calcium Carbonate Aerogel

    Directory of Open Access Journals (Sweden)

    Johann Plank

    2009-01-01

    Full Text Available We report on a facile method for the preparation of a calcium carbonate aerogel consisting of aggregated secondary vaterite particles with an approximate average diameter of 50 nm. It was synthesized via a sol-gel process by reacting calcium oxide with carbon dioxide in methanol and subsequent supercritical drying of the alcogel with carbon dioxide. The resulting monolith was opaque, brittle and had overall dimensions of 6×2×1 cm. It was characterized by X-ray powder diffraction, nitrogen adsorption method (BET, and scanning electron microscopy.

  14. Improved preparation and cooperative calcium contraction of glycerinated Vorticella.

    Science.gov (United States)

    Asai, H; Ochiai, T; Fukui, K; Watanabe, M; Kano, F

    1978-03-01

    An improved method for the preparation of glycerinated Vorticella convallaria was investigated. The pretreatment of living vorticellas with a medium containing 0.1% saponins and subsequent treatment with an extraction medium containing 35% glycerol at about 0 degrees C was satisfactory. The equilibrium average length of contractile stalks of glycerinated vorticellas was measured at various free calcium concentrations in the reaction medium. It was found that the contractile element in the spasmoneme of the stalk is contracted by a cooperative interaction involving at least two calcium ions.

  15. Plasma Calcium, Inorganic Phosphate and Magnesium During Hypocalcaemia Induced by a Standardized EDTA Infusion in Cows

    Directory of Open Access Journals (Sweden)

    Enemark JMD

    2001-06-01

    Full Text Available The intravenous Na2EDTA infusion technique allows effective specific chelation of circulating Ca2+ leading to a progressive hypocalcaemia. Methods previously used were not described in detail and results obtained by monitoring total and free ionic calcium were not comparable due to differences in sampling and analysis. This paper describes a standardized EDTA infusion technique that allowed comparison of the response of calcium, phosphorus and magnesium between 2 groups of experimental cows. The concentration of the Na2EDTA solution was 0.134 mol/l and the flow rate was standardized at 1.2 ml/kg per hour. Involuntary recumbency occurred when ionised calcium dropped to 0.39 – 0.52 mmol/l due to chelation. An initial fast drop of ionized calcium was observed during the first 20 min of infusion followed by a fluctuation leading to a further drop until recumbency. Pre-infusion [Ca2+] between tests does not correlate with the amount of EDTA required to induce involuntary recumbence. Total calcium concentration measured by atomic absorption remained almost constant during the first 100 min of infusion but declined gradually when the infusion was prolonged. The concentration of inorganic phosphate declined gradually in a fluctuating manner until recumbency. Magnesium concentration remained constant during infusion. Such electrolyte responses during infusion were comparable to those in spontaneous milk fever. The standardized infusion technique might be useful in future experimental studies.

  16. The efficiency of child formula dentifrices containing different calcium and phosphate compounds on artificial enamel caries

    Science.gov (United States)

    Rirattanapong, Praphasri; Vongsavan, Kadkao; Saengsirinavin, Chavengkiat; Khumsub, Ploychompoo

    2016-01-01

    Objectives: Fluoride toothpaste has been extensively used to prevent dental caries. However, the risk of fluorosis is concerning, especially in young children. Calcium phosphate has been an effective remineralizing agent and is present in commercial dental products, with no risk of fluorosis to users. This in vitro study aimed to compare the effects of different calcium phosphate compounds and fluoride-containing dentifrices on artificial caries in primary teeth. Materials and Methods: Fifty sound primary incisors were coated with nail varnish, leaving two 1 mm2 windows on the labial surface before immersion in demineralizing solution for 96 hours to produce artificial enamel lesions. Subsequently, one window from each tooth was coated with nail varnish, and all 50 teeth were divided into five groups (n = 10); group A – deionized water; group B – casein phosphopeptide–amorphous calcium phosphate (CPP–ACP) paste (Tooth Mousse); group C – 500 ppm F (Colgate Spiderman®); group D – nonfluoridated toothpaste with triple calcium phosphate (Pureen®); and group E – tricalcium phosphate (TCP). Polarized light microscopy and Image-Pro® Plus software were used to evaluate lesions. Results: After a 7-day pH-cycle, mean lesion depths in groups A, B, C, D, and E had increased by 57.52 ± 10.66%, 33.28 ± 10.16%, 17.04 ± 4.76%, 32.51 ± 8.99%, and 21.76 ± 8.15%, respectively. All data were processed by the Statistical Package for the Social Sciences (version 16.0) software package. Comparison of percentage changes using one-way analysis of variance and Fisher's least squares difference tests at a 95% level of confidence demonstrated that group A was significantly different from the other groups (P < 0.001). Lesions in groups B and D had a significant lesion progression when compared with groups C and E. Conclusions: All toothpastes in this study had the potential to delay the demineralization progression of artificial enamel caries in primary teeth. The

  17. In Situ Laser Coating of Calcium Phosphate on TC4 Surface for Enhancing Bioactivity

    Institute of Scientific and Technical Information of China (English)

    DENG Chi; WANG Yong; ZHANG Ya-ping; GAO Jia-cheng

    2007-01-01

    Titanium alloy has been a successful implant material owing to its excellent ratio of strength to weight,toughness, and bio-inert oxide surface. Significant progress has been made in improving the bioactivity of titanium alloy by coating its oxide surface with calcium phosphates. In the present study, in situ coating was reported on Ti6Al4V(TC4) surface with calcium phosphate (Ca-P) bioceramics synthesized and synchronously cladded by laser beam. This coating was grown by first preplacing directly the raw powders, which contain 80% of CaHPO4 ·2H2O, 20% of CaCO3, and dram of rare earth (RE), on the TC4 surfaces, and then exposing the surfaces to the laser beam with a power density of 12. 73-15.27 MW · m-2 and a scanning velocity of 10. 5 m/s. The resultant coating was characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric analysis and Different-thermal Scanning (TG-DSC), and Energy Dispersive X-ray Detection (EDX). The results show that these laser ceramics include hydroxyapatite (HA), tricalcium phosphate (TCP), Ca2P2O7, and other Ca-P phases, and the interface between the coating and the TC4 substrate has tighter fixation, in which the chemical bonding is approved. These laser hybrid coatings are useful in enhancing the bioactivity of titanium alloy surfaces.

  18. Influences of the steam sterilization on the properties of calcium phosphate porous bioceramics.

    Science.gov (United States)

    Li, Xiangfeng; Guo, Bo; Xiao, Yumei; Yuan, Tun; Fan, Yujiang; Zhang, Xingdong

    2016-01-01

    The influences of steam sterilization on the physicochemical properties of calcium phosphate (Ca-P) porous bioceramics, including β-tricalcium phosphate (β-TCP), biphasic calcium phosphate (BCP) and hydroxyapatite (HA) are investigated. After being steam sterilized in an autoclave (121 °C for 40 min), the porous bioceramics are dried and characterized. The steam sterilization has no obvious effects on the phase composition, thermal stability, pH value and dissolubility of β-TCP porous bioceramic, but changes its morphology and mechanical strength. Meanwhile, the steam sterilization leads to the significant changes of the morphology, phase composition, pH value and dissolubility of BCP porous bioceramic. The increase of dissolubility and mechanical strength, the decrease of pH value of the immersed solution and partial oriented growth of crystals are also observed in HA porous bioceramic after steam sterilization. These results indicate that the steam sterilization can result in different influences on the physicochemical properties of β-TCP, BCP and HA porous bioceramics, thus the application of the steam sterilization on the three kinds of Ca-P porous bioceramics should be considered carefully based on the above changed properties.

  19. Hemolysis effect and calcium-phosphate precipitation of heat-organic-film treated magnesium

    Institute of Scientific and Technical Information of China (English)

    GAO Jia-cheng; QIAO Li-ying; LI Long-chuan; WANG Yong

    2006-01-01

    A heat-organic-films process was employed to induce calcium-phosphate apatites formation on magnesium, consequently the corrosion resistance and hemolysis properties of magnesium were improved for biomedical applications. Firstly, magnesium samples were heat-treated at 773 K for 10 h; secondly, stearic acid films were coated on the surface of the heat-treated magnesium.Then the surface modified magnesium was soaked in simulated body fluid (SBF) to test its corrosion resistance. The results show that the heat treatment process allows magnesium to form a dense oxide layer with a thickness of around 20 μm, thereby the surface modified magnesium has higher corrosion resistance. After 24 h in SBF island apatite was deposited on magnesium. The unevenly precipitates were characterized by XRD and FTIR as the mixture of hydroxyapatite(HA) and octacalcium phosphate(OCP). The preliminary hemolysis experiment indicates that untreated magnesium has hemolytic effect (about 60%); whereas the heat-organic film treated samples has no hemolytic effect. The mechanism of fast nucleation and growth of calcium-phosphate apatites on surface modified magnesium in SBF was also discussed.

  20. Solid-liquid adsorption of calcium phosphate on TiO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Chusuei, C.C.; Goodman, D.W.; Stipdonk, M.J. van; Justes, D.R.; Loh, K.H.; Schweikert, E.A.

    1999-10-12

    Calcium phosphate (CP) in aqueous solution was exposed to thin-film TiO{sub 2} surfaces at predetermined times ranging from 10 min to 20 h using a liquid reaction apparatus (LRA). Surface analysis was then performed using X-ray photoelectron (XPS) and Auger electron (AES) spectroscopies and time-of-flight secondary ion mass spectromemtry (ToF-SIMS) with polyatomic primary ions. XPS revealed that CP nucleated and grew on the TiO{sub 2} surface, with phosphate groups growing on top of an initial 2-dimensional (2D) Ca-rich layer. AES depth profiling of a 4-h solution exposure complemented this finding and gave additional evidence for 3-dimensional (3D) phosphate islands forming on top of the calcium. ToF-SIMS analysis of CP adsorbed on the surface indicated that the predominant phase on the surface was brushite, CaHPO{sub 4}{sm{underscore}bullet}2H{sub 2}O. A model for Ca{sup 2+} cation bridging at the oxide interface is proposed.

  1. Synthesis and characterization of the aluminium phosphates modified with ammonium, calcium and molybdenum by hydrothermal method

    Directory of Open Access Journals (Sweden)

    Łuczka Kinga

    2016-06-01

    Full Text Available Synthesis and characterization of the aluminum phosphates modified with ammonium, calcium and molybdenum were conducted. The influence of process parameters (reactive pressure and molar ratios in the reaction mixture were studied. The contents of the individual components in the products were in the range of: 10.97–17.31 wt% Al, 2.65–13.32 wt% Ca, 0.70–3.11 wt% Mo, 4.36–8.38 wt% NH3, and 35.12–50.54 wt% P2O5. The materials obtained in the experiments were characterized by various physicochemical parameters. The absorption oil number was in the range from 67 to 89 of oil/100 g of product, the surface area was within the range of 4–76 m2/g, whereas the average particle size of products reached 282–370 nm. The Tafel tests revealed comparable anticorrosive properties of aluminum phosphates modified with ammonium, calcium, molybdenum in comparison with commercial phosphate.

  2. Focus Ion Beam/Scanning Electron Microscopy Characterization of Osteoclastic Resorption of Calcium Phosphate Substrates.

    Science.gov (United States)

    Diez-Escudero, Anna; Espanol, Montserrat; Montufar, Edgar B; Di Pompo, Gemma; Ciapetti, Gabriela; Baldini, Nicola; Ginebra, Maria-Pau

    2017-02-01

    This article presents the application of dual focused ion beam/scanning electron microscopy (FIB-SEM) imaging for preclinical testing of calcium phosphates with osteoclast precursor cells and how this high-resolution imaging technique is able to reveal microstructural changes at a level of detail previously not possible. Calcium phosphate substrates, having similar compositions but different microstructures, were produced using low- and high-temperature processes (biomimetic calcium-deficient hydroxyapatite [CDHA] and stoichiometric sintered hydroxyapatite, respectively). Human osteoclast precursor cells were cultured for 21 days before evaluating their resorptive potential on varying microstructural features. Alternative to classical morphological evaluation of osteoclasts (OC), FIB-SEM was used to observe the subjacent microstructure by transversally sectioning cells and observing both the cells and the substrates. Resorption pits, indicating OC activity, were visible on the smoother surface of high-temperature sintered hydroxyapatite. FIB-SEM analysis revealed signs of acidic degradation on the grain surface under the cells, as well as intergranular dissolution. No resorption pits were evident on the surface of the rough CDHA substrates. However, whereas no degradation was detected by FIB sections in the material underlying some of the cells, early stages of OC-mediated acidic degradation were observed under cells with more spread morphology. Collectively, these results highlight the potential of FIB to evaluate the resorptive activity of OC, even in rough, irregular, or coarse surfaces where degradation pits are otherwise difficult to visualize.

  3. Injectable PLGA microsphere/calcium phosphate cements: physical properties and degradation characteristics.

    Science.gov (United States)

    Habraken, W J E M; Wolke, J G C; Mikos, A G; Jansen, J A

    2006-01-01

    Calcium phosphate (CaP) cements show an excellent biocompatibility and often have a high mechanical strength, but in general degrade relatively slow. To increase degradation rates, macropores can be introduced into the cement, e.g., by the inclusion of biodegradable microspheres into the cement. The aim of this research is to develop an injectable PLGA microsphere/CaP cement with sufficient setting/cohesive properties and good mechanical and physical properties. PLGA microspheres were prepared using a water-in-oil-in-water double-emulsion technique. The CaP-cement used was Calcibon, a commercially available hydroxyapatite-based cement. 10:90 and 20:80 dry wt% PLGA microsphere/CaP cylindrical scaffolds were prepared as well as microporous cement (reference material). Injectability, setting time, cohesive properties and porosity were determined. Also, a 12-week degradation study in PBS (37 degree C) was performed. Results showed that injectability decreased with an increase in PLGA microsphere content. Initial and final setting time of the PLGA/CaP samples was higher than the microporous sample. Porosity of the different formulations was 40.8% (microporous), 60.2% (10:90) and 69.3% (20:80). The degradation study showed distinct mass loss and a pH decrease of the surrounding medium starting from week 6 with the 10:90 and 20:80 formulations, indicating PLGA erosion. Compression strength of the PLGA microsphere/CaP samples decreased siginificantly in time, the microporous sample remained constant. After 12 weeks both PLGA/CaP samples showed a structure of spherical micropores and had a compressive strength of 12.2 MPa (10:90) and 4.3 MPa (20:80). Signs of cement degradation were also found with the 20:80 formulation. In conclusion, all physical parameters were well within workable ranges with both 10:90 and 20:80 PLGA microsphere/CaP cements. After 12 weeks the PLGA was totally degraded and a highly porous, but strong scaffold remained.

  4. Reactive calcium-phosphate-containing poly(ester-co-ether) methacrylate bone adhesives: chemical, mechanical and biological considerations.

    Science.gov (United States)

    Zhao, Xin; Olsen, Irwin; Li, Haoying; Gellynck, Kris; Buxton, Paul G; Knowles, Jonathan C; Salih, Vehid; Young, Anne M

    2010-03-01

    A poly(propylene glycol-co-lactide) dimethacrylate adhesive with monocalcium phosphate monohydrate (MCPM)/beta-tricalcium phosphate (beta-TCP) fillers in various levels has been investigated. Water sorption by the photo-polymerized materials catalyzed varying filler conversio