WorldWideScience

Sample records for preliminary experiments designed

  1. Design, integration and preliminary results of the IXV Catalysis experiment

    Science.gov (United States)

    Viladegut, Alan; Panerai, F.; Chazot, O.; Pichon, T.; Bertrand, P.; Verdy, C.; Coddet, C.

    2016-08-01

    The CATalytic Experiment (CATE) is an in-flight demonstration of catalysis effects at the surface of thermal protection materials. A high-catalytic coating was applied over the baseline ceramic material on the windward side of the intermediate experimental vehicle (IXV). The temperature jump due to different catalytic activities was detected during re-entry through measurements made with near-surface thermocouples on the windward side of the vehicle. The experiment aimed at contributing to the development and validation of gas/surface interaction models for re-entry applications. The present paper summarizes the design of CATE and its integration on the windward side of the IXV. Results of a qualification campaign at the Plasmatron facility of the von Karman Institute for Fluid Dynamics are presented. They provided an experimental evidence of the temperature jump at the low-to-high catalytic interface of the heat shield under aerothermal conditions relevant to the actual IXV flight. These tests also gave confidence so that the high-catalytic patch would not endanger the integrity of the vehicle and the safety of the mission. A preliminary assessment of flight data from the thermocouple measurements shows consistency with results of the qualification tests.

  2. AGC-1 Experiment and Final Preliminary Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Robert L. Bratton; Tim Burchell

    2006-08-01

    This report details the experimental plan and design as of the preliminary design review for the Advanced Test Reactor Graphite Creep-1 graphite compressive creep capsule. The capsule will contain five graphite grades that will be irradiated in the Advanced Test Reactor at the Idaho National Laboratory to determine the irradiation induced creep constants. Seven other grades of graphite will be irradiated to determine irradiated physical properties. The capsule will have an irradiation temperature of 900 C and a peak irradiation dose of 5.8 x 10{sup 21} n/cm{sup 2} [E > 0.1 MeV], or 4.2 displacements per atom.

  3. Preliminary Design of a Pendulum Experiment for Searching for a Lorentz-Violation Signal

    CERN Document Server

    Shao, Cheng-Gang; Tan, Yu-Jie

    2016-01-01

    This work mainly presents a preliminary design for a pendulum experiment with both the source mass and the test mass in a striped pattern to amplify the Lorentz-violation signal, since the signal is sensitive to edge effects.

  4. Muon-catalyzed fusion experiment target and detector system. Preliminary design report

    Energy Technology Data Exchange (ETDEWEB)

    Jones, S.E.; Watts, K.D.; Caffrey, A.J.; Walter, J.B.

    1982-03-01

    We present detailed plans for the target and particle detector systems for the muon-catalyzed fusion experiment. Requirements imposed on the target vessel by experimental conditions and safety considerations are delineated. Preliminary designs for the target vessel capsule and secondary containment vessel have been developed which meet these requirements. In addition, the particle detection system is outlined, including associated fast electronics and on-line data acquisition. Computer programs developed to study the target and detector system designs are described.

  5. Kinetics experiments and bench-scale system: Background, design, and preliminary experiments

    Energy Technology Data Exchange (ETDEWEB)

    Rofer, C.K.

    1987-10-01

    The project, Supercritical Water Oxidation of Hazardous Chemical Waste, is a Hazardous Waste Remedial Actions Program (HAZWRAP) Research and Development task being carried out by the Los Alamos National Laboratory. Its objective is to obtain information for use in understanding the basic technology and for scaling up and applying oxidation in supercritical water as a viable process for treating a variety of DOE-DP waste streams. This report gives the background and rationale for kinetics experiments on oxidation in supercritical water being carried out as a part of this HAZWRAP Research and Development task. It discusses supercritical fluid properties and their relevance to applying this process to the destruction of hazardous wastes. An overview is given of the small emerging industry based on applications of supercritical water oxidation. Factors that could lead to additional applications are listed. Modeling studies are described as a basis for the experimental design. The report describes plug flow reactor and batch reactor systems, and presents preliminary results. 28 refs., 4 figs., 5 tabs.

  6. Experiments, conceptual design, preliminary cost estimates and schedules for an underground research facility

    Energy Technology Data Exchange (ETDEWEB)

    Korbin, G.; Wollenberg, H.; Wilson, C.; Strisower, B.; Chan, T.; Wedge, D.

    1981-09-01

    Plans for an underground research facility are presented, incorporating techniques to assess the hydrological and thermomechanical response of a rock mass to the introduction and long-term isolation of radioactive waste, and to assess the effects of excavation on the hydrologic integrity of a repository and its subsequent backfill, plugging, and sealing. The project is designed to utilize existing mine or civil works for access to experimental areas and is estimated to last 8 years at a total cost for contruction and operation of $39.0 million (1981 dollars). Performing the same experiments in an existing underground research facility would reduce the duration to 7-1/2 years and cost $27.7 million as a lower-bound estimate. These preliminary plans and estimates should be revised after specific sites are identified which would accommodate the facility.

  7. An overview of the Tokamak Physics Experiment vacuum vessel preliminary design

    Energy Technology Data Exchange (ETDEWEB)

    Rocco, R.E. [Raytheon Engineers and Constructors, Inc., Princeton, NJ (United States)

    1995-12-31

    The mission of the Tokamak Physics Experiment (TPX) Project is to develop the scientific basis for a compact and continuously operating tokamak fusion reactor. The vacuum vessel, which consists of a double walled torus, ports and supports, is a major element of the TPX machine. This paper provides an overview of the vacuum vessel preliminary design work. The design of the vacuum vessel is being carried out by an industrial team under subcontract to the Princeton Plasma Physics Laboratory. The respective work scopes of this team are discussed. The role of concurrent engineering is presented in the context of this design-build subcontract. A discussion of the engineering requirements, material selection rationale and vacuum vessel configuration is provided. Titanium 6Al-4V will be used to fabricate the vacuum vessel. Significant material concerns were identified with the use of titanium; hydrogen embrittlement and the effects of borated water were the major issues. A research and development (R and D) program was established to resolve these material issues as well as to develop the vessel weld details. A comprehensive analytical effort was established to perform the structural and thermal analysis of the vessel. Design details of the vessel, supports, ports, and flanges are presented.

  8. Preliminary experiment design of graphite dust emission measurement under accident conditions for HTGR

    Energy Technology Data Exchange (ETDEWEB)

    Peng, Wei, E-mail: pengwei@tsinghua.edu.cn [Institute of Nuclear and New Energy Technology of Tsinghua University, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 100084 (China); Chen, Tao; Sun, Qi; Wang, Jie [Institute of Nuclear and New Energy Technology of Tsinghua University, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 100084 (China); Yu, Suyuan, E-mail: suyuan@tsinghua.edu.cn [Center for Combustion Energy, The Key Laboratory for Thermal Science and Power Engineering, Ministry of Education, Tsinghua University, Beijing 100084 (China)

    2017-05-15

    Highlights: • A theoretical analysis is used to predict the total graphite dust release for an AVR LOCA. • Similarity criteria must be satisfied between the experiment and the actual HTGR system. • Model experiments should be conducted to predict the graphite dust resuspension rate. - Abstract: The graphite dust movement behavior is significant for the safety analyses of high-temperature gas cooled reactor (HTGR). The graphite dust release for accident conditions is an important source term for HTGR safety analyses. Depressurization release tests are not practical in HTGR because of a radioactivity release to the environment. Thus, a theoretical analysis and similarity principles were used to design a group of modeling experiments. Modeling experiments for fan start-up and depressurization process and actual experiments of helium circulator start-up in an HTGR were used to predict the rate of graphite dust resuspension and the graphite dust concentration, which can be used to predict the graphite dust release during accidents. The modeling experiments are easy to realize and the helium circulator start-up test does not harm the reactor system or the environment, so this experiment program is easily achieved. The revised Rock’n’Roll model was then used to calculate the AVR reactor release. The calculation results indicate that the total graphite dust releases during a LOCA will be about 0.65 g in AVR.

  9. Potential flow calculations and preliminary wing design in support of an NLF variable sweep transition flight experiment

    Science.gov (United States)

    Waggoner, E. G.; Phillips, P. S.; Viken, J. K.; Davis, W. H.

    1985-01-01

    NASA Langley and NASA Ames-Dryden have defined a variable-sweep transition-flight experiment utilizing the F-14 aircraft to enhance understanding of the interaction of crossflow and Tollmien-Schlichting instabilities on a laminar-boundary-layer transition. The F-14 wing outer panel will be modified to generate favorable pressure gradients on the upper wing surface over a wide range of flight conditions. Extensive computations have been performed using two-dimensional and three-dimensional transonic analysis codes. Flight-test and computational data are compared and shown to validate the applicability of the three-dimensional codes (WBPPW and TAWFIVE). In addition, results from two preliminary glove designs derived from two different approaches to the design problem are presented. Advantages and disadvantages of each approach are identified, and it is concluded that coupling an analysis code with an automated design procedure yields a powerful code with distinct advantages over a 'cut-and-dry' approach.

  10. Preliminary design of laser-induced breakdown spectroscopy for proto-Material Plasma Exposure eXperiment.

    Science.gov (United States)

    Shaw, G; Martin, M Z; Martin, R; Biewer, T M

    2014-11-01

    Laser-induced breakdown spectroscopy (LIBS) is a technique for measuring surface matter composition. LIBS is performed by focusing laser radiation onto a target surface, ablating the surface, forming a plasma, and analyzing the light produced. LIBS surface analysis is a possible diagnostic for characterizing plasma-facing materials in ITER. Oak Ridge National Laboratory has enabled the initial installation of a laser-induced breakdown spectroscopy diagnostic on the prototype Material-Plasma Exposure eXperiment (Proto-MPEX), which strives to mimic the conditions found at the surface of the ITER divertor. This paper will discuss the LIBS implementation on Proto-MPEX, preliminary design of the fiber optic LIBS collection probe, and the expected results.

  11. Designing assisted living technologies ‘in the wild’: preliminary experiences with cultural probe methodology

    Directory of Open Access Journals (Sweden)

    Wherton Joseph

    2012-12-01

    , limited emotional or psychological resources, life events, and acute illness. Discussions between researchers and participants about the materials collected (and sometimes about what had prevented them completing the tasks helped elicit further information relevant to assisted living technology design. The probe materials were particularly helpful when having conversations with non-English speaking participants through an interpreter. Conclusions Cultural probe methods can help build a rich picture of the lives and experiences of older people to facilitate the co-production of assisted living technologies. But their application may be constrained by the participant’s physical, mental and emotional capacity. They are most effective when used as a tool to facilitate communication and development of a deeper understanding of older people’s needs.

  12. Preliminary Design Study of High-Power H2+ Cyclotrons for the DAEdALUS Experiment

    CERN Document Server

    Calabretta, L; Gammino, S; Rifuggiato, D; Ciavola, G; Maggiore, M; Piazza, L A C; Alonso, J R; Barletta, W A; Calanna, A; Conrad, J M

    2011-01-01

    This report provides a first design for H2+ accelerators as the DAEdALUS neutrino sources. A description of all aspects of the system, from the ion source to the extracted beam, is provided. The analysis provides a first proof of principle of a full cyclotron system which can provide the necessary beam power for the CP violation search proposed by the DAEdALUS Collaboration.

  13. Amplitude Tapers for Planar Arrays Using the McClellan Transformation: Concepts and Preliminary Design Experiments

    Science.gov (United States)

    2010-04-29

    transformation: a phase-only prototype transforms to a two-dimensional taper that lacks the phase-only property. A straightforward IEEE Xplore subject search...A 2-D FIR filter structure derived from the Chebyshev recursion,” IEEE Trans. Circuits and Systems, vol. 24, no. 7, pp. 372–378, July 1977. [Online...transformations for two-dimensional digital filtering—Part I: Design,” IEEE Trans. Circuits and Systems, 3It is odd to associate the term “recursion” with FIR

  14. Characterize Behaviour of Emerging Pollutants in Artificial Recharge: Column Experiments - Experiment Design and Results of Preliminary Tests

    Science.gov (United States)

    Wang, H.; Carrera, J.; Ayora, C.; Licha, T.

    2012-04-01

    Emerging pollutants (EPs) have been detected in water resources as a result of human activities in recent years. They include pharmaceuticals, personal care products, dioxins, flame retardants, etc. They are a source of concern because many of them are resistant to conventional water treatment, and they are harmful to human health, even in low concentrations. Generally, this study aims to characterize the behaviour of emerging pollutants in reclaimed water in column experiments which simulates artificial recharge. One column set includes three parts: influent, reactive layer column (RLC) and aquifer column (AC). The main influent is decided to be Secondary Effluent (SE) of El Prat Wastewater Treatment Plant, Barcelona. The flow rate of the column experiment is 0.9-1.5 mL/min. the residence time of RLC is designed to be about 1 day and 30-40 days for AC. Both columns are made of stainless steel. Reactive layer column (DI 10cm * L55cm) is named after the filling material which is a mixture of organic substrate, clay and goethite. One purpose of the application of the mixture is to increase dissolve organic carbon (DOC). Leaching test in batchs and columns has been done to select proper organic substrate. As a result, compost was selected due to its long lasting of releasing organic matter (OM). The other purpose of the application of the mixture is to enhance adsorption of EPs. Partition coefficients (Kow) of EPs indicate the ability of adsorption to OM. EPs with logKow>2 could be adsorbed to OM, like Ibuprofen, Bezafibrate and Diclofenac. Moreover, some of EPs are charged in the solution with pH=7, according to its acid dissociation constant (Ka). Positively charged EPs, for example Atenolol, could adsorb to clay. In the opposite, negatively charged EPs, for example Gemfibrozil, could adsorb to goethite. Aquifer column (DI 35cm * L1.5m) is to simulate the processes taking place in aquifer in artificial recharge. The filling of AC has two parts: silica sand and

  15. KALIMER preliminary conceptual design report

    Energy Technology Data Exchange (ETDEWEB)

    Hahn, Do Hee; Kim, Y. J.; Kim, Y. G. and others

    2000-08-01

    This report, which summarizes the result of preliminary conceptual design activities during Phase 1, follows the format of safety analysis report. The purpose of publishing this report is to gather all of the design information developed so far in a systematic way so that KALIMER designers have a common source of the consistent design information necessary for their future design activities. This report will be revised and updated as design changes occur and more detailed design specification is developed during Phase 2. Chapter 1 describes the KALIMER Project. Chapter 2 includes the top level design requirements of KALIMER and general plant description. Chapter 3 summarizes the design of structures, components, equipment and systems. Specific systems and safety analysis results are described in the remaining chapters. Appendix on the HCDA evaluation is attached at the end of this report.

  16. Preliminary format design guidelines

    DEFF Research Database (Denmark)

    Tosello, Guido; Calaon, Matteo; Nørregaard, J.

    2013-01-01

    The strategic research centre PolyNano aims at becoming the Danish competence centre for production-ready fabrication of polymer, nano-scale lab-on-a-chip (LoC) devices. In order to provide a competitive edge for Danish biotech companies launching LoC products by removal of the technology barrier...... between lab-scale proof-of-principle and high-volume low-cost production of LoCs, the PolyNano project will develop a readily accessible fabrication platform for those companies aiming at developing and manufacturing their LoCs design.......The strategic research centre PolyNano aims at becoming the Danish competence centre for production-ready fabrication of polymer, nano-scale lab-on-a-chip (LoC) devices. In order to provide a competitive edge for Danish biotech companies launching LoC products by removal of the technology barrier...

  17. Design and test of an extremely high resolution Timing Counter for the MEG II experiment: preliminary results

    CERN Document Server

    De Gerone, M; Ootani, W; Uchiyama, Y; Nishimura, M; Shirabe, S; Cattaneo, P W; Rossella, M

    2013-01-01

    The design and tests of Timing Counter elements for the upgrade of the MEG experiment, MEG II,is presented. The detector is based on several small plates of scintillator with a Silicon PhotoMultipliers dual-side readout. The optimisation of the single counter elements (SiPMs, scintillators, geometry) is described. Moreover, the results obtained with a first prototype tested at the Beam Test Facility (BTF) of the INFN Laboratori Nazionali di Frascati (LNF) are presented.

  18. Ship design methodologies of preliminary design

    CERN Document Server

    Papanikolaou, Apostolos

    2014-01-01

    This book deals with ship design and in particular with methodologies of the preliminary design of ships. The book is complemented by a basic bibliography and five appendices with useful updated charts for the selection of the main dimensions and other basic characteristics of different types of ships (Appendix A), the determination of hull form  from the data of systematic hull form series (Appendix B), the detailed description of the relational method for the preliminary estimation of ship weights (Appendix C), a brief review of the historical evolution of shipbuilding science and technology from the prehistoric era to date (Appendix D) and finally a historical review of regulatory developments of ship's damage stability to date (Appendix E).  The book can be used as textbook for ship design courses or as additional reading for university or college students of naval architecture courses and related disciplines; it may also serve as a reference book for naval architects, practicing engineers of rel...

  19. Experimenting with a design experiment

    Directory of Open Access Journals (Sweden)

    Bakker, Judith

    2012-12-01

    Full Text Available The design experiment is an experimental research method that aims to help design and further develop new (policy instruments. For the development of a set of guidelines for the facilitation of citizens’ initiatives by local governments, we are experimenting with this method. It offers good opportunities for modeling interventions by testing their instrumental validity –the usefulness for the intended practical purposes. At the same time design experiments are also useful for evaluating the empirical validity of theoretical arguments and the further development of these arguments in the light of empirical evidence (by using e.g. the technique of pattern matching. We describe how we have applied this methodology in two cases and discuss our research approach. We encountered some unexpected difficulties, especially in the cooperation with professionals and citizens. These difficulties complicate the valid attribution of causal effects to the use of the new instrument. However, our preliminary conclusion is that design experiments are useful in our field of study

    El experimento de diseño es un método de investigación experimental que tiene como objetivo diseñar y desarrollar posteriormente nuevas herramientas (políticas. En este artículo experimentamos con este método para desarrollar un conjunto de directrices que permitan a los gobiernos locales facilitar las iniciativas ciudadanas. El método ofrece la oportunidad de modelar las intervenciones poniendo a prueba su validez instrumental (su utilidad para el fin práctico que se proponen. Al mismo tiempo, los experimentos de diseño son útiles también para evaluar la validez empírica de las discusiones teóricas y el posterior desarrollo de esas discusiones a la luz de la evidencia empírica (usando, por ejemplo, técnicas de concordancia de patrones. En este trabajo describimos cómo hemos aplicado este método a dos casos y discutimos nuestro enfoque de

  20. Preliminary design data package. Appendix C

    Energy Technology Data Exchange (ETDEWEB)

    1979-07-25

    The design requirements, design philosophy, method and assumptions, and preliminary computer-aided design of the Near-Term Hybrid Vehicle including its electric and heat power units, control equipment, transmission system, body, and overall vehicle characteristics are presented. (LCL)

  1. Preliminary design for a maglev development facility

    Energy Technology Data Exchange (ETDEWEB)

    Coffey, H.T.; He, J.L.; Chang, S.L.; Bouillard, J.X.; Chen, S.S.; Cai, Y.; Hoppie, L.O.; Lottes, S.A.; Rote, D.M. [Argonne National Lab., IL (United States); Zhang, Z.Y. [Polytechnic Univ., Brooklyn, NY (United States); Myers, G.; Cvercko, A. [Sterling Engineering, Westchester, IL (United States); Williams, J.R. [Alfred Benesch and Co., Chicago, IL (United States)

    1992-04-01

    A preliminary design was made of a national user facility for evaluating magnetic-levitation (maglev) technologies in sizes intermediate between laboratory experiments and full-scale systems. A technical advisory committee was established and a conference was held to obtain advice on the potential requirements of operational systems and how the facility might best be configured to test these requirements. The effort included studies of multiple concepts for levitating, guiding, and propelling maglev vehicles, as well as the controls, communications, and data-acquisition and -reduction equipment that would be required in operating the facility. Preliminary designs for versatile, dual 2-MVA power supplies capable of powering attractive or repulsive systems were developed. Facility site requirements were identified. Test vehicles would be about 7.4 m (25 ft) long, would weigh form 3 to 7 metric tons, and would operate at speeds up to 67 m/s (150 mph) on a 3.3-km (2.05-mi) elevated guideway. The facility would utilize modular vehicles and guideways, permitting the substitution of levitation, propulsion, and guideway components of different designs and materials for evaluation. The vehicle would provide a test cell in which individual suspension or propulsion components or subsystems could be tested under realistic conditions. The system would allow economical evaluation of integrated systems under varying weather conditions and in realistic geometries.

  2. Preliminary design for a maglev development facility

    Energy Technology Data Exchange (ETDEWEB)

    Coffey, H.T.; He, J.L.; Chang, S.L.; Bouillard, J.X.; Chen, S.S.; Cai, Y.; Hoppie, L.O.; Lottes, S.A.; Rote, D.M. (Argonne National Lab., IL (United States)); Zhang, Z.Y. (Polytechnic Univ., Brooklyn, NY (United States)); Myers, G.; Cvercko, A. (Sterling Engineering, Westchester, IL (United States)); Williams, J.R. (Alfred Benesch and Co., Chicago, IL (United States))

    1992-04-01

    A preliminary design was made of a national user facility for evaluating magnetic-levitation (maglev) technologies in sizes intermediate between laboratory experiments and full-scale systems. A technical advisory committee was established and a conference was held to obtain advice on the potential requirements of operational systems and how the facility might best be configured to test these requirements. The effort included studies of multiple concepts for levitating, guiding, and propelling maglev vehicles, as well as the controls, communications, and data-acquisition and -reduction equipment that would be required in operating the facility. Preliminary designs for versatile, dual 2-MVA power supplies capable of powering attractive or repulsive systems were developed. Facility site requirements were identified. Test vehicles would be about 7.4 m (25 ft) long, would weigh form 3 to 7 metric tons, and would operate at speeds up to 67 m/s (150 mph) on a 3.3-km (2.05-mi) elevated guideway. The facility would utilize modular vehicles and guideways, permitting the substitution of levitation, propulsion, and guideway components of different designs and materials for evaluation. The vehicle would provide a test cell in which individual suspension or propulsion components or subsystems could be tested under realistic conditions. The system would allow economical evaluation of integrated systems under varying weather conditions and in realistic geometries.

  3. Preliminary design for a MAGLEV development facility

    Science.gov (United States)

    Coffey, H. T.; He, J. L.; Chang, S. L.; Bouillard, J. X.; Chen, S. S.; Cai, Y.; Hoppie, L. O.; Lottes, S. A.; Rote, D. M.; Zhang, Z. Y.

    1992-04-01

    A preliminary design was made of a national user facility for evaluating magnetic-levitation (maglev) technologies in sizes intermediate between laboratory experiments and full-scale systems. A technical advisory committee was established and a conference was held to obtain advice on the potential requirements of operational systems and how the facility might best be configured to test these requirements. The effort included studies of multiple concepts for levitating, guiding, and propelling maglev vehicles, as well as the controls, communications, and data-acquisition and -reduction equipment that would be required in operating the facility. Preliminary designs for versatile, dual 2-MVA power supplies capable of powering attractive or repulsive systems were developed. Facility site requirements were identified. Test vehicles would be about 7.4 m (25 ft) long, would weigh from 3 to 7 metric tons, and would operate at speeds up to 67 m/s (150 mph) on a 3.3-km (2.05-mi) elevated guideway. The facility would utilize modular vehicles and guideways, permitting the substitution of levitation, propulsion, and guideway components of different designs and materials for evaluation. The vehicle would provide a test cell in which individual suspension or propulsion components or subsystems could be tested under realistic conditions. The system would allow economical evaluation of integrated systems under varying weather conditions and in realistic geometries.

  4. ERIS: preliminary design phase overview

    Science.gov (United States)

    Kuntschner, Harald; Jochum, Lieselotte; Amico, Paola; Dekker, Johannes K.; Kerber, Florian; Marchetti, Enrico; Accardo, Matteo; Brast, Roland; Brinkmann, Martin; Conzelmann, Ralf D.; Delabre, Bernard A.; Duchateau, Michel; Fedrigo, Enrico; Finger, Gert; Frank, Christoph; Rodriguez, Fernando G.; Klein, Barbara; Knudstrup, Jens; Le Louarn, Miska; Lundin, Lars; Modigliani, Andrea; Müller, Michael; Neeser, Mark; Tordo, Sebastien; Valenti, Elena; Eisenhauer, Frank; Sturm, Eckhard; Feuchtgruber, Helmut; George, Elisabeth M.; Hartl, Michael; Hofmann, Reiner; Huber, Heinrich; Plattner, Markus P.; Schubert, Josef; Tarantik, Karl; Wiezorrek, Erich; Meyer, Michael R.; Quanz, Sascha P.; Glauser, Adrian M.; Weisz, Harald; Esposito, Simone; Xompero, Marco; Agapito, Guido; Antichi, Jacopo; Biliotti, Valdemaro; Bonaglia, Marco; Briguglio, Runa; Carbonaro, Luca; Cresci, Giovanni; Fini, Luca; Pinna, Enrico; Puglisi, Alfio T.; Quirós-Pacheco, Fernando; Riccardi, Armando; Di Rico, Gianluca; Arcidiacono, Carmelo; Dolci, Mauro

    2014-07-01

    The Enhanced Resolution Imager and Spectrograph (ERIS) is the next-generation adaptive optics near-IR imager and spectrograph for the Cassegrain focus of the Very Large Telescope (VLT) Unit Telescope 4, which will soon make full use of the Adaptive Optics Facility (AOF). It is a high-Strehl AO-assisted instrument that will use the Deformable Secondary Mirror (DSM) and the new Laser Guide Star Facility (4LGSF). The project has been approved for construction and has entered its preliminary design phase. ERIS will be constructed in a collaboration including the Max- Planck Institut für Extraterrestrische Physik, the Eidgenössische Technische Hochschule Zürich and the Osservatorio Astrofisico di Arcetri and will offer 1 - 5 μm imaging and 1 - 2.5 μm integral field spectroscopic capabilities with a high Strehl performance. Wavefront sensing can be carried out with an optical high-order NGS Pyramid wavefront sensor, or with a single laser in either an optical low-order NGS mode, or with a near-IR low-order mode sensor. Due to its highly sensitive visible wavefront sensor, and separate near-IR low-order mode, ERIS provides a large sky coverage with its 1' patrol field radius that can even include AO stars embedded in dust-enshrouded environments. As such it will replace, with a much improved single conjugated AO correction, the most scientifically important imaging modes offered by NACO (diffraction limited imaging in the J to M bands, Sparse Aperture Masking and Apodizing Phase Plate (APP) coronagraphy) and the integral field spectroscopy modes of SINFONI, whose instrumental module, SPIFFI, will be upgraded and re-used in ERIS. As part of the SPIFFI upgrade a new higher resolution grating and a science detector replacement are envisaged, as well as PLC driven motors. To accommodate ERIS at the Cassegrain focus, an extension of the telescope back focal length is required, with modifications of the guider arm assembly. In this paper we report on the status of the

  5. Airborne Use of Traffic Intent Information in a Distributed Air-Ground Traffic Management Concept: Experiment Design and Preliminary Results

    Science.gov (United States)

    Wing, David J.; Adams, Richard J.; Barmore, Bryan E.; Moses, Donald

    2002-01-01

    This paper presents initial findings of a research study designed to provide insight into the issue of intent information exchange in constrained en-route air-traffic operations and its effect on pilot decision making and flight performance. The piloted simulation was conducted in the Air Traffic Operations Laboratory at the NASA Langley Research Center. Two operational modes for autonomous operations were compared under conditions of low and high operational complexity. The tactical mode was characterized primarily by the use of state information for conflict detection and resolution and an open-loop means for the pilot to meet operational constraints. The strategic mode involved the combined use of state and intent information, provided the pilot an additional level of alerting, and allowed a closed-loop approach to meeting operational constraints. Operational constraints included separation assurance, schedule adherence, airspace hazard avoidance, flight efficiency, and passenger comfort. Potential operational benefits of both modes are illustrated through several scenario case studies. Subjective pilot ratings and comments comparing the tactical and strategic modes are presented.

  6. Design and analysis of experiments with SAS

    CERN Document Server

    Lawson, John

    2010-01-01

    IntroductionStatistics and Data Collection Beginnings of Statistically Planned Experiments Definitions and Preliminaries Purposes of Experimental Design Types of Experimental Designs Planning Experiments Performing the Experiments Use of SAS SoftwareCompletely Randomized Designs with One Factor Introduction Replication and Randomization A Historical Example Linear Model for Completely Randomized Design (CRD) Verifying Assumptions of the Linear Model Analysis Strategies When Assumptions Are Violated Determining the Number of Replicates Comparison of Treatments after the F-TestFactorial Designs

  7. STACEE-32: Design, performance, and preliminary results

    Science.gov (United States)

    Ong, Rene A.

    2000-06-01

    The Solar Tower Atmospheric Cherenkov Effect Experiment (STACEE) is designed to detect astrophysical sources of γ-rays at energies between 25 and 500 GeV. STACEE uses large solar mirrors (heliostats) to collect the atmospheric Cherenkov radiation produced in γ-ray air showers. The use of a large mirror collection area will allow STACEE to probe γ-ray sources at energies above the reach of the Compton Gamma Ray Observatory (CGRO), but below the reach of conventional Cherenkov telescopes. During the 1998-99 observing season, a portion of STACEE using 32 heliostats was installed at the National Solar Thermal Test Facility (NSTTF) of Sandia National Laboratories (Albuquerque, NM). This initial configuration (STACEE-32) observed a number of astronomical sources, including the Crab and several active galactic nuclei (AGN). Here we report on these observations. We highlight the experimental configuration and the preliminary results from the Crab data. The full STACEE experiment using 64 heliostats will be commissioned in 2000. .

  8. Designing learning experiences

    National Research Council Canada - National Science Library

    Collins, Jannette

    2007-01-01

    Creation of significant learning experiences follows basic steps of instructional design related to situational factors, goals and objectives, feedback and evaluation methods, teaching and learning...

  9. Preliminary design package for Sunair SEC-601 solar collector

    Science.gov (United States)

    1978-01-01

    The preliminary design of the Owens-Illinois model Sunair SEC-601 tubular air solar collector is presented. Information in this package includes the subsystem design and development approaches, hazard analysis, and detailed drawings available as the preliminary design review.

  10. Preliminary aerothermodynamic design method for hypersonic vehicles

    Science.gov (United States)

    Harloff, G. J.; Petrie, S. L.

    1987-01-01

    Preliminary design methods are presented for vehicle aerothermodynamics. Predictions are made for Shuttle orbiter, a Mach 6 transport vehicle and a high-speed missile configuration. Rapid and accurate methods are discussed for obtaining aerodynamic coefficients and heat transfer rates for laminar and turbulent flows for vehicles at high angles of attack and hypersonic Mach numbers.

  11. A Toolbox for Rotorcraft Preliminary Design

    OpenAIRE

    Lier, Max; Krenik, Alex; Kunze, Philipp; Kohlgrüber, Dieter; Schwinn, Dominik; Lützenberger, Marius

    2015-01-01

    The German Aerospace Center (DLR) developed a toolbox, which is able to reflect the conceptual and preliminary design process of rotorcraft configuration. Such a toolbox is a valuable aid for the design engineer and can be used for the assessment of new technologies with regard to the overall configuration. This toolbox is currently extended to model novel rotorcraft configurations. Automated optimization procedures will be added in the future as well. This paper describes the too...

  12. Preliminary results from the MINERvA experiment

    Energy Technology Data Exchange (ETDEWEB)

    Harris, Deborah A.; /Fermilab

    2011-11-01

    The MINERvA experiment, operating since 2009 in the NuMI neutrino beam line at Fermilab, has collected neutrino and antineutrino scattering data on a variety of nuclear targets. The detector is designed to identify events originating in plastic scintillator, lead, carbon, iron, water, and liquid helium. The goal of the experiment is to measure inclusive and exclusive cross sections for neutrino and antineutrino with much greater precision than previous experiments. We present preliminary kinematic distributions for charged current quasi-elastic scattering and other processes.

  13. Designing Urban Experiences

    DEFF Research Database (Denmark)

    Jantzen, Christian; Vetner, Mikael

    2008-01-01

    traditional urban planning aspects such as infrastructure, environmental factors and aesthetics, but has also dealt with the design of urban experiences. Through an introduction of the framework of the structure of experiences, this article examines how urban experiences can be understood and analysed...

  14. Deep Underground Science and Engineering Laboratory - Preliminary Design Report

    CERN Document Server

    Lesko, Kevin T; Alonso, Jose; Bauer, Paul; Chan, Yuen-Dat; Chinowsky, William; Dangermond, Steve; Detwiler, Jason A; De Vries, Syd; DiGennaro, Richard; Exter, Elizabeth; Fernandez, Felix B; Freer, Elizabeth L; Gilchriese, Murdock G D; Goldschmidt, Azriel; Grammann, Ben; Griffing, William; Harlan, Bill; Haxton, Wick C; Headley, Michael; Heise, Jaret; Hladysz, Zbigniew; Jacobs, Dianna; Johnson, Michael; Kadel, Richard; Kaufman, Robert; King, Greg; Lanou, Robert; Lemut, Alberto; Ligeti, Zoltan; Marks, Steve; Martin, Ryan D; Matthesen, John; Matthew, Brendan; Matthews, Warren; McConnell, Randall; McElroy, William; Meyer, Deborah; Norris, Margaret; Plate, David; Robinson, Kem E; Roggenthen, William; Salve, Rohit; Sayler, Ben; Scheetz, John; Tarpinian, Jim; Taylor, David; Vardiman, David; Wheeler, Ron; Willhite, Joshua; Yeck, James

    2011-01-01

    The DUSEL Project has produced the Preliminary Design of the Deep Underground Science and Engineering Laboratory (DUSEL) at the rehabilitated former Homestake mine in South Dakota. The Facility design calls for, on the surface, two new buildings - one a visitor and education center, the other an experiment assembly hall - and multiple repurposed existing buildings. To support underground research activities, the design includes two laboratory modules and additional spaces at a level 4,850 feet underground for physics, biology, engineering, and Earth science experiments. On the same level, the design includes a Department of Energy-shepherded Large Cavity supporting the Long Baseline Neutrino Experiment. At the 7,400-feet level, the design incorporates one laboratory module and additional spaces for physics and Earth science efforts. With input from some 25 science and engineering collaborations, the Project has designed critical experimental space and infrastructure needs, including space for a suite of multi...

  15. Preliminary designs: passive solar manufactured housing. Technical status report

    Energy Technology Data Exchange (ETDEWEB)

    1980-05-12

    The criteria established to guide the development of the preliminary designs are listed. Three preliminary designs incorporating direct gain and/or sunspace are presented. Costs, drawings, and supporting calculations are included. (MHR)

  16. Preliminary design of a coffee harvester

    Directory of Open Access Journals (Sweden)

    Raphael Magalhães Gomes Moreira

    2016-10-01

    Full Text Available Design of an agricultural machine is a highly complex process due to interactions between the operator, machine, and environment. Mountain coffee plantations constitute an economic sector that requires huge investments for the development of agricultural machinery to improve the harvesting and post-harvesting processes and to overcome the scarcity of work forces in the fields. The aim of this study was to develop a preliminary design for a virtual prototype of a coffee fruit harvester. In this study, a project methodology was applied and adapted for the development of the following steps: project planning, informational design, conceptual design, and preliminary design. The construction of a morphological matrix made it possible to obtain a list of different mechanisms with specific functions. The union between these mechanisms resulted in variants, which were weighed to attribute scores for each selected criterion. From each designated proposal, two variants with the best scores were selected and this permitted the preparation of the preliminary design of both variants. The archetype was divided in two parts, namely the hydraulically articulated arms and the harvesting system that consisted of the vibration mechanism and the detachment mechanism. The proposed innovation involves the use of parallel rods, which were fixed in a plane and rectangular metal sheet. In this step, dimensions including a maximum length of 4.7 m, a minimum length of 3.3 m, and a total height of 2.15 m were identified based on the functioning of the harvester in relation to the coupling point of the tractor.

  17. Democratic design experiments

    DEFF Research Database (Denmark)

    Ehn, Pelle; Brandt, Eva; Halse, Joachim

    2016-01-01

    we here see design engagements which are both controversial in their commitment to agendas of social change and experimental in the sense that they openly probe for what can possibly be enacted. In this conversation we want to explore how such engagements may be seen as democratic design experiments...

  18. Democratic design experiments

    DEFF Research Database (Denmark)

    Ehn, Pelle; Brandt, Eva; Halse, Joachim

    2016-01-01

    we here see design engagements which are both controversial in their commitment to agendas of social change and experimental in the sense that they openly probe for what can possibly be enacted. In this conversation we want to explore how such engagements may be seen as democratic design experiments...

  19. Preliminary design of the Space Station internal thermal control system

    Science.gov (United States)

    Herrin, Mark T.; Patterson, David W.; Turner, Larry D.

    1987-01-01

    The baseline preliminary design configuration of the Internal Thermal Control system (ITCS) of the U.S. Space Station pressurized elements (i.e., the Habitation and U.S. Laboratory modules, pressurized logistics carrier, and resources nodes) is defined. The ITCS is composed of both active and passive components. The subsystems which comprise the ITCS are identified and their functional descriptions are provided. The significant trades and analyses, which were performed during Phase B (i.e., the preliminary design phase) that resulted in the design described herein, are discussed. The ITCS interfaces with the station's central Heat Rejection and Transport System (HRTS), other systems, and externally attached pressurized payloads are described. Requirements on the ITCS with regard to redundancy and experiment support are also addressed.

  20. PRELIMINARY SELECTION OF MGR DESIGN BASIS EVENTS

    Energy Technology Data Exchange (ETDEWEB)

    J.A. Kappes

    1999-09-16

    The purpose of this analysis is to identify the preliminary design basis events (DBEs) for consideration in the design of the Monitored Geologic Repository (MGR). For external events and natural phenomena (e.g., earthquake), the objective is to identify those initiating events that the MGR will be designed to withstand. Design criteria will ensure that radiological release scenarios resulting from these initiating events are beyond design basis (i.e., have a scenario frequency less than once per million years). For internal (i.e., human-induced and random equipment failures) events, the objective is to identify credible event sequences that result in bounding radiological releases. These sequences will be used to establish the design basis criteria for MGR structures, systems, and components (SSCs) design basis criteria in order to prevent or mitigate radiological releases. The safety strategy presented in this analysis for preventing or mitigating DBEs is based on the preclosure safety strategy outlined in ''Strategy to Mitigate Preclosure Offsite Exposure'' (CRWMS M&O 1998f). DBE analysis is necessary to provide feedback and requirements to the design process, and also to demonstrate compliance with proposed 10 CFR 63 (Dyer 1999b) requirements. DBE analysis is also required to identify and classify the SSCs that are important to safety (ITS).

  1. Preliminary safety design analysis of KALIMER

    Energy Technology Data Exchange (ETDEWEB)

    Suk, Soo Dong; Kwon, Y. M.; Kim, K. D. [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-03-01

    The national long-term R and D program updated in 1997 requires Korea Atomic Energy Research Institute(KAERI) to complete by the year 2006 the basic design of Korea Advanced Liquid Metal Reactor (KALIMER), along with supporting R and D work, with the capability of resolving the issue of spent fuel storage as well as with significantly enhanced safety. KALIMER is a 150 MWe pool-type sodium cooled prototype reactor that uses metallic fuel. The conceptual design is currently under way to establish a self consistent design meeting a set of the major safety design requirements for accident prevention. Some of current emphasis include those for inherent and passive means of negative reactivity insertion and decay heat removal, high shutdown reliability, prevention of and protection from sodium chemical reaction, and high seismic margin, among others. All of these requirements affect the reactor design significantly and involve supporting R and D programs of substance. This document first introduces a set of safety design requirements and accident evaluation criteria established for the conceptual design of KALIMER and then summarizes some of the preliminary results of engineering and design analyses performed for the safety of KALIMER. 19 refs., 19 figs., 6 tabs. (Author)

  2. ISSA/TSS power preliminary design

    Science.gov (United States)

    Main, John A.

    1996-01-01

    A projected power shortfall during the initial utilization flights of the International Space Station Alpha (ISSA) has prompted an inquiry into the use of the Tethered Satellite System (TSS) to provide station power. The preliminary design of the combined ISSA/TSS system is currently underway in the Preliminary Design Office at the Marshall Space Flight Center. This document focuses on the justification for using a tether system on space station, the physical principles behind such a system, and how it might be operated to best utilize its capabilities. The basic components of a simple DC generator are a magnet of some type and a conductive wire. Moving the wire through the magnetic field causes forces to be applied to the electric charges in the conductor, and thus current is induced to flow. This simple concept is the idea behind generating power with space-borne tether systems. The function of the magnet is performed by the earth's magnetic field, and orbiting a conductive tether about the earth effectively moves the tether through the field.

  3. CTF3 Design Report Preliminary Phase

    CERN Document Server

    Allard, D; Bernard, M; Bertuzzi, J P; Bienvenu, G; Bonzano, R; Bossart, Rudolf; Braun, H; Bravin, Enrico; Borburgh, J; Buttkus, J; Chazarenc, E; Chaput, R; Chohan, V; Cloye, J J; Corsini, R; Coudert, G; Damiani, M; Deghaye, S; Delahaye, J P; Di Maio, F; Dobers, T; Dubief, P; Dupuy, B; Durieu, L; Ferrari, A; Garvey, Terence; Geschonke, Günther; Hansen, J; Hellgren, H; Hourican, M; Lamidon, M; Le Duff, J; Lefèvre, T; Lewis, J H; Lindroos, J; Mahner, E; McMonagle, G; Monteiro, J; Mourier, J; Mouton, B; Odier, P; Otto, T; Pearce, P; Pittin, R; Poehler, M; Potier, J P; Raich, U; Rettig, M; Rinolfi, Louis; Risselada, Thys; Riva, R; Rossat, G; Royer, P; Sermeus, L; Setas, K; Simonet, G; Sladen, Jonathan P H; Søby, L; Tanner, L; Tecker, F A; Thomi, J C; Wilson, Ian H; Yvon, G

    2001-01-01

    The design of CLIC is based on a two-beam scheme, where the short pulses of high power 30 GHz RF are extracted from a drive beam running parallel to the main beam. The 3rd generation CLIC Test Facility (CTF3) will demonstrate the generation of the drive beam with the appropriate time structure, the extraction of 30 GHz RF power from this beam, as well as acceleration of a probe beam with 30 GHz RF cavities. The project makes maximum use of existing equipment and infrastructure of the LPI complex, which became available after the closure of LEP. In the first stage of the project, the "Preliminary Phase", the existing LIL linac and the EPA ring, both modified to suit the new requirements, are used to investigate the technique of frequency multiplication by means of interleaving bunches from subsequent trains. This report describes the design of this phase.

  4. Involving Motion Graphics in Spatial Experience Design

    DEFF Research Database (Denmark)

    Steijn, Arthur

    2013-01-01

    process, and therefore it should be constructed as such. Since the development of the design model has this double focus, I involve design students in design laboratories related to my practice as a teacher in visual communication design and production design. I also reflect on how an initial design...... conceptualization of various design elements in an analysis of the way in which these elements are integrated and used in the creation of particular experiences of space, atmosphere and artistic expression. On the basis of this analysis I present a preliminary construction of a design model including some design...... laboratory may be set-up and used. Finally I describe how this design lab can be used as a method for creating both practical knowledge of the manner in which the design model may be applied in actual design processes, as well as how these processes can be used for pointing out design elements or dimensions...

  5. NSLS-II Preliminary Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Dierker, S.

    2007-11-01

    Following the CD0 approval of the National Synchrotron Light Source II (NSLS-II) during August 2005, Brookhaven National Laboratory prepared a conceptual design for a worldclass user facility for scientific research using synchrotron radiation. DOE SC review of the preliminary baseline in December 2006 led to the subsequent CD1 approval (approval of alternative selection and cost range). This report is the documentation of the preliminary design work for the NSLS-II facility. The preliminary design of the Accelerator Systems (Part 1) was developed mostly based of the Conceptual Design Report, except for the Booster design, which was changed from in-storage-ring tunnel configuration to in external- tunnel configuration. The design of beamlines (Part 2) is based on designs developed by engineering firms in accordance with the specification provided by the Project. The conventional facility design (Part 3) is the Title 1 preliminary design by the AE firm that met the NSLS-II requirements. Last and very important, Part 4 documents the ES&H design and considerations related to this preliminary design. The NSLS-II performance goals are motivated by the recognition that major advances in many important technology problems will require scientific breakthroughs in developing new materials with advanced properties. Achieving this will require the development of new tools that will enable the characterization of the atomic and electronic structure, chemical composition, and magnetic properties of materials, at nanoscale resolution. These tools must be nondestructive, to image and characterize buried structures and interfaces, and they must operate in a wide range of temperatures and harsh environments. The NSLS-II facility will provide ultra high brightness and flux and exceptional beam stability. It will also provide advanced insertion devices, optics, detectors, and robotics, and a suite of scientific instruments designed to maximize the scientific output of the facility

  6. NSLS-II Preliminary Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Dierker, S.

    2007-11-01

    Following the CD0 approval of the National Synchrotron Light Source II (NSLS-II) during August 2005, Brookhaven National Laboratory prepared a conceptual design for a worldclass user facility for scientific research using synchrotron radiation. DOE SC review of the preliminary baseline in December 2006 led to the subsequent CD1 approval (approval of alternative selection and cost range). This report is the documentation of the preliminary design work for the NSLS-II facility. The preliminary design of the Accelerator Systems (Part 1) was developed mostly based of the Conceptual Design Report, except for the Booster design, which was changed from in-storage-ring tunnel configuration to in external- tunnel configuration. The design of beamlines (Part 2) is based on designs developed by engineering firms in accordance with the specification provided by the Project. The conventional facility design (Part 3) is the Title 1 preliminary design by the AE firm that met the NSLS-II requirements. Last and very important, Part 4 documents the ES&H design and considerations related to this preliminary design. The NSLS-II performance goals are motivated by the recognition that major advances in many important technology problems will require scientific breakthroughs in developing new materials with advanced properties. Achieving this will require the development of new tools that will enable the characterization of the atomic and electronic structure, chemical composition, and magnetic properties of materials, at nanoscale resolution. These tools must be nondestructive, to image and characterize buried structures and interfaces, and they must operate in a wide range of temperatures and harsh environments. The NSLS-II facility will provide ultra high brightness and flux and exceptional beam stability. It will also provide advanced insertion devices, optics, detectors, and robotics, and a suite of scientific instruments designed to maximize the scientific output of the facility

  7. Preliminary conceptual design about the CEPC calorimeters

    Science.gov (United States)

    Yang, Haijun

    2016-11-01

    The Circular Electron Positron Collider (CEPC) as a Higgs factory was proposed in September 2013. The preliminary conceptual design report was completed in 2015.1 The CEPC detector design was using International Linear Collider Detector — ILD2 as an initial baseline. The CEPC calorimeters, including the high granularity electromagnetic calorimeter (ECAL) and the hadron calorimeter (HCAL), are designed for precise energy measurements of electrons, photons, taus and hadronic jets. The basic resolution requirements for the ECAL and HCAL are about 16%E (GeV) and 50%E (GeV), respectively. To fully exploit the physics potential of the Higgs, W, Z and related Standard Model processes, the jet energy resolution is required to reach 3%-4%, or 30%/E (GeV) at energies below about 100 GeV. To achieve the required performance, a Particle Flow Algorithm (PFA) — oriented calorimetry system is being considered as the baseline design. The CEPC ECAL detector options include silicon-tungsten or scintillator-tungsten structures with analog readout, while the HCAL detector options have scintillator or gaseous detector as the active sensor and iron as the absorber. Some latest R&D studies about ECAL and HCAL within the CEPC working group is also presented.

  8. Preliminary Opto-Mechanical Design for the X2000 Transceiver

    Science.gov (United States)

    Hemmati, H.; Page, N. A.

    2000-01-01

    Preliminary optical design and mechanical conceptual design for a 30 cm aperture transceiver are described. A common aperture is used for both transmit and receive. Special attention was given to off-axis and scattered light rejection and isolation of the receive channel from the transmit channel. Requirements, details of the design and preliminary performance analysis of the transceiver are provided.

  9. Preliminary design package for Sunair SEC-601 solar collector

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-01

    This report presents the preliminary design of the Owens-Illinois mode Sunair SEC-601 tubular air solar collector. Information in this package includes the Subsystem Design and Development Approaches, hazard analysis, and detailed drawings available as the Preliminary Design Review.

  10. Designing learning experiences.

    Science.gov (United States)

    Collins, Jannette

    2007-01-01

    Creation of significant learning experiences follows basic steps of instructional design related to situational factors, goals and objectives, feedback and evaluation methods, teaching and learning activities, alignment of the preceding elements, and course evaluation. Goals should reflect what students will learn at the end of the course and what will still be with them several years later. Objectives should focus on learner performance, not teacher performance, and on behavior, not subject matter; there should be only one learning outcome per objective. Students learn more and retain their knowledge longer if they acquire it in an active rather than a passive manner. The situational factors, goals and objectives, feedback and evaluation, and teaching and learning activities should all reflect and support each other. The act of course evaluation closes the educational loop of design, implement, evaluate, and modify. (c) RSNA, 2007.

  11. Emergency design framework: a satellite preliminary scheme design

    Institute of Scientific and Technical Information of China (English)

    TENG Hongfei; WANG Yishou; ZHANG Bao

    2007-01-01

    The emergency design of mechanical products or equipment(such as a satellite)is significant for disaster relief when the natural disasters occur.Most of us are unaware about the little information that is available in literature about emergency designs.Against the background of the preliminary scheme design of satellite payloads,emergency design was studied in the case of natural disasters.We presented some definitions about emergency design.Then,we proposed the basic ideas of how to realize the emergency design.These ideas were inspired by two aspects:1)the evolutionary algorithms,the agent,the human-computer cooperation,and the collaborative design theory;2)the emergency behaviors in ant colonies.Following the ideas,first we constructed the human-computer cooperation agents(hereinafter called the HC-Agents)that combine the human intelligence with evolutionary algorithms.These HC-Agents had specific features like the division of labor in the ant colony.Second,we developed the multiagents cooperative design system on the basis of a hybrid P2P(peer-to-peer)model.Therefore,the emergency design system has shown some capabilities,such as anti-interference,adaptation,and rapid response.

  12. Real Life Experiences with Experience Design

    DEFF Research Database (Denmark)

    Dalsgård, Peter; Halskov, Kim

    2006-01-01

    Experience Design is an emergent field of study, and various approaches to the field abound. In this paper, we take a pragmatic approach to identifying key aspects of an experience design process, by reporting on a project involving the design of experience-oriented applications of interactive...... technologies for knowledge dissemination and marketing, in cooperation with public institutions and businesses. We argue that collaborative formulation of core design intentions and values is a valuable instrument in guiding experience design processes, and present three cases from this project, two of which...... the installations, the core values established to guide the design process and the intended use contexts. We argue that the installations present a broad spectrum of experience design installations that can assist designers in understanding the relations between core values, intentions, use context and interface...

  13. Sequential Design of Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Anderson-Cook, Christine Michaela [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-06-30

    A sequential design of experiments strategy is being developed and implemented that allows for adaptive learning based on incoming results as the experiment is being run. The plan is to incorporate these strategies for the NCCC and TCM experimental campaigns to be run in the coming months. This strategy for experimentation has the advantages of allowing new data collected during the experiment to inform future experimental runs based on their projected utility for a particular goal. For example, the current effort for the MEA capture system at NCCC plans to focus on maximally improving the quality of prediction of CO2 capture efficiency as measured by the width of the confidence interval for the underlying response surface that is modeled as a function of 1) Flue Gas Flowrate [1000-3000] kg/hr; 2) CO2 weight fraction [0.125-0.175]; 3) Lean solvent loading [0.1-0.3], and; 4) Lean solvent flowrate [3000-12000] kg/hr.

  14. Preliminary design of pseudo satellites: Basic methods and feasibility criteria

    Science.gov (United States)

    Klimenko, N. N.

    2016-12-01

    Analytical models of weight and energy balances, aerodynamic models, and solar irradiance models to perform pseudo-satellite preliminary design are presented. Feasibility criteria are determined in accordance with the aim of preliminary design dependent on mission scenario and type of payload.

  15. Design of Computer Experiments

    DEFF Research Database (Denmark)

    Dehlendorff, Christian

    The main topic of this thesis is design and analysis of computer and simulation experiments and is dealt with in six papers and a summary report. Simulation and computer models have in recent years received increasingly more attention due to their increasing complexity and usability. Software...... that the sources of variation of the simulation model can be divided in two components corresponding to changes in the environmental factors (the uncontrollable factor settings) and to random variation. Moreover, the structure of the environmental effects can be estimated, which can be used to put the system...... in a more robust operating mode. The interpolation technique called Kriging is the topic of Paper F, which is a widely applied technique for building so called models-for-the-model (metamodels). We propose a method that handles both qualitative and quantitative factors, which is not covered by the standard...

  16. The deuteron accelerator preliminary design for BISOL

    Energy Technology Data Exchange (ETDEWEB)

    Peng, S.X., E-mail: sxpeng@pku.edu.cn; Zhu, F.; Wang, Z.; Gao, Y.; Guo, Z.Y.

    2016-06-01

    BISOL, which was named as Beijing-ISOL before (Cui et al., 2013), is the abbreviation of Beijing Isotope-Separation-On-Line neutron beam facility. It is proposed jointly by Peking University (PKU) and China Institute of Atomic Energy (CIAE) for basic science study and application. It is a double driven facility that can be driven by a reactor or a deuteron accelerator. The deuteron driver accelerator should accelerate the deuteron beam up to 40 MeV with maximum beam current of 10 mA. Proton beams up to 33 MeV and He{sup 2+} beams up to 81.2 MeV can also be accelerated in this accelerator. The accelerator can be operated on either CW (continuous waveform) or pulsed mode, and the ion energy can be adjusted in a wide range. The accelerator will also allow independent operation of the RIB (Radioactive Ion Beams) system. It will be mainly charged by PKU group. Details of the deuteron accelerator preliminary design for BISOL will be given in this paper.

  17. Preliminary design of surrounding heliostat fields

    Energy Technology Data Exchange (ETDEWEB)

    Collado, Francisco J. [Zaragoza University, Dpto. de Ingenieria Mecanica, CPS-B, Maria de Luna 3, 50018 Zaragoza (Spain)

    2009-05-15

    Recently, the author has shown elsewhere a simplified model that allows quick evaluations of the annual overall energy collected by a surrounding heliostat field. This model is the combination of an analytical flux density function produced by a heliostat, developed by the own author, and an optimized mirror density distribution developed by University of Houston for the Solar One Project. As main conclusion of this previous work, it was recognized that such pseudo-continuous simplified model should not substitute much more accurate discrete evaluations, which manage thousands of individual heliostat coordinates. Here in this work, the difficulty of generating a preliminary discrete layout of a large number of heliostats is addressed. The main novelty is the direct definition of thousands of heliostat coordinates through basically two parameters i.e. a simplified blocking factor and an additional security distance. Such procedure, which was formerly theoretically suggested by the author, is put into practice here, showing examples and commenting their problems and advantages. Getting a previous set of thousands of heliostat coordinates would be a major first step in the complex process of designing solar power tower (SPT). (author)

  18. ALMA Nutator Design and Preliminary Performance

    CERN Document Server

    Martin-Cocher, Pierre; Koch, Patrick M; Ni, Chih-Wen; Chen, Wei-Long; Chen, Ming-Tang; Raffin, Philippe; Ong, Chin-Long; Ho, Paul T P; Symmes, Arthur

    2013-01-01

    We report the past two years of collaboration between the di?erent actors on the ALMA nutator. Building on previous developments, the nutator has seen changes in much of the design. A high-modulus carbon ?fiber structure has been added on the back of the mirror in order to transfer the voice coils forces with less deformation, thus reducing delay problems due to flexing. The controller is now an off?-the-shelf National Instrument NI-cRIO, and the ampli?fier a class D servo drive from Advanced Motion Controls, with high peak power able to drive the coils at 300 Volts DC. The stow mechanism has been totally redesigned to improve on the repeatability and precision of the stow position, which is also the reference for the 26 bits Heidenhain encoders. This also improves on the accuracy of the stow position with wind loading. Finally, the software, written largely with National Instrument's LabView, has been developed. We will discuss these changes and the preliminary performances achieved to date. Keywords: ALMA, ...

  19. The deuteron accelerator preliminary design for BISOL

    Science.gov (United States)

    Peng, S. X.; Zhu, F.; Wang, Z.; Gao, Y.; Guo, Z. Y.

    2016-06-01

    BISOL, which was named as Beijing_ISOL before (Cui et al., 2013), is the abbreviation of Beijing Isotope-Separation-On-Line neutron beam facility. It is proposed jointly by Peking University (PKU) and China Institute of Atomic Energy (CIAE) for basic science study and application. It is a double driven facility that can be driven by a reactor or a deuteron accelerator. The deuteron driver accelerator should accelerate the deuteron beam up to 40 MeV with maximum beam current of 10 mA. Proton beams up to 33 MeV and He2+ beams up to 81.2 MeV can also be accelerated in this accelerator. The accelerator can be operated on either CW (continuous waveform) or pulsed mode, and the ion energy can be adjusted in a wide range. The accelerator will also allow independent operation of the RIB (Radioactive Ion Beams) system. It will be mainly charged by PKU group. Details of the deuteron accelerator preliminary design for BISOL will be given in this paper.

  20. User Experience Design in Webpage Design

    Institute of Scientific and Technical Information of China (English)

    许钰伟

    2014-01-01

    User experience design is becoming more and more important. It originates from network as well as screen products interactive with users, whose scope is very wide. Although research orientations are different, their objective is the same, that is, to make users enjoy the simplest usage mode and reduce thinking in use; Although there is uncertainty, for some specific user group, the similarity of user experience can be recognized by excellent design;Although user experience is at the initial stage, with higher demand of comfort degree in surfing the internet, user experience design will be the core of future website design.

  1. Design Experiments in Educational Research.

    Science.gov (United States)

    Cobb, Paul; Confrey, Jere; diSessa, Andrea; Lehrer, Richard; Schauble, Leona

    2003-01-01

    Indicates the range of purposes and variety of settings in which design experiments have been conducted, delineating five crosscutting features that collectively differentiate design experiments from other methodologies. Clarifies what is involved in preparing for and carrying out a design experiment and in conducting a retrospective analysis of…

  2. The "SCORPION" experiment onboard the International Space Station. Preliminary results.

    Science.gov (United States)

    Borisov, V; Deshevaya, E; Grachov, E; Grigoryan, O; Tchurilo, I; Tsetlin, V

    2003-01-01

    The "SCORPION" program onboard the Russian Segment (RS) of the International Space Station (ISS) is designed to carry out complex research of the effects of the nar-Earth space parameters on the conditions under which various experiments and operations are being conducted. Special attention in this program was paid to the biological objects onboard the orbital station, e.g. it was found that variation in the number of colony forming units (micromicets and bacteria) correlates with the solar activity and the absorbed dose. The "SCORPION" experiment onboard the RS ISS started in January 2002. It was designed to measure the following parameters inside the space absorbed doses in different places inside the RS ISS, the fluxes of energetic charged particles, neutrons and gamma-quanta; the vectors of the magnetic field and low-frequency electromagnetic waves. At the same time the growth of micromicets on the samples of various materials was studied. The description of the "SCORPION" experiment and the preliminary results obtained onboard the RS ISS in 2002 are presented.

  3. A novel approach to an anatomical adapted stent design for the percutaneous therapy of tricuspid valve diseases: preliminary experiences from an engineering point of view.

    Science.gov (United States)

    Pott, Desiree; Malasa, Margarita; Urban, Ute; Kütting, Maximilian; Safi, Yara; Roggenkamp, Jan; Steinseifer, Ulrich; Hatam, Nima; Autschbach, Rüdiger; Spillner, Jan; Amerini, Andrea

    2012-01-01

    Tricuspid valve regurgitation mostly occurs as result of dilation of the right ventricle, secondary to left heart valve diseases. Until recently, little attention has been given to the development of percutaneous therapeutic tools exclusively designed for tricuspid valve disease. A new approach to the interventional therapy of tricuspid regurgitation, in particular, the design of a conceptual new valve-bearing, self-expansible stent, is presented here. A three-dimensional computer model of a right porcine heart was developed to gain a realistic anatomical geometry. The new design consists of two tubular stent elements, one inside the superior vena cava and the other inside the tricuspid valve annulus after being eventually equipped with a biological valve prosthesis, which are connected by struts. Anchoring to the heart structure is provided primarily by the vena cava stent, strengthened by the struts. The stents are designed to be cut from a 10 mm tube and later expanded to their designated diameter. Simulation software analyzing the expansion process with respect to the intended geometrical design is used in an iterative process. A validation of the anatomical geometry and function of the stent design inside a silicone model within in vitro tests and a random porcine heart shows an accurate anatomical fitting.

  4. Preliminary design package for prototype solar heating system

    Science.gov (United States)

    1978-01-01

    A summary is given of the preliminary analysis and design activity on solar heating systems. The analysis was made without site specific data other than weather; therefore, the results indicate performance expected under these special conditions. Major items include system candidates, design approaches, trade studies and other special data required to evaluate the preliminary analysis and design. The program calls for the development and delivery of eight prototype solar heating and cooling systems for installation and operational test.

  5. Methodology for Preliminary Design of Electrical Microgrids

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, Richard P. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Stamp, Jason E. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Eddy, John P. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Henry, Jordan M [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Munoz-Ramos, Karina [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Abdallah, Tarek [U.S. Army Corps of Engineers, Washington, DC (United States)

    2015-09-30

    Many critical loads rely on simple backup generation to provide electricity in the event of a power outage. An Energy Surety Microgrid TM can protect against outages caused by single generator failures to improve reliability. An ESM will also provide a host of other benefits, including integration of renewable energy, fuel optimization, and maximizing the value of energy storage. The ESM concept includes a categorization for microgrid value proposi- tions, and quantifies how the investment can be justified during either grid-connected or utility outage conditions. In contrast with many approaches, the ESM approach explic- itly sets requirements based on unlikely extreme conditions, including the need to protect against determined cyber adversaries. During the United States (US) Department of Defense (DOD)/Department of Energy (DOE) Smart Power Infrastructure Demonstration for Energy Reliability and Security (SPIDERS) effort, the ESM methodology was successfully used to develop the preliminary designs, which direct supported the contracting, construction, and testing for three military bases. Acknowledgements Sandia National Laboratories and the SPIDERS technical team would like to acknowledge the following for help in the project: * Mike Hightower, who has been the key driving force for Energy Surety Microgrids * Juan Torres and Abbas Akhil, who developed the concept of microgrids for military installations * Merrill Smith, U.S. Department of Energy SPIDERS Program Manager * Ross Roley and Rich Trundy from U.S. Pacific Command * Bill Waugaman and Bill Beary from U.S. Northern Command * Melanie Johnson and Harold Sanborn of the U.S. Army Corps of Engineers Construc- tion Engineering Research Laboratory * Experts from the National Renewable Energy Laboratory, Idaho National Laboratory, Oak Ridge National Laboratory, and Pacific Northwest National Laboratory

  6. Design and construction of a spectrometer facility and experiment for intermediate energy proton scattering on helium. [Wave functions, preliminary experimental techniques

    Energy Technology Data Exchange (ETDEWEB)

    Rolfe, R.M.

    1976-12-01

    The goal of the research was to investigate proton scattering on nuclei at intermediate energies and in particular to investigate proton scattering on helium. A theoretical investigation of the helium nucleus and the nature of the intermediate energy interaction, design and optimization of an energy-loss spectrometer facility for proton-nucleus scattering, and the unique superfluid helium target and experimental design are discussed.

  7. Preliminary design review: Brayton Isotope Power System

    Energy Technology Data Exchange (ETDEWEB)

    none,

    1977-03-01

    The design aspects covered include flight system design, design criteria/margins/reliability, GDS design, system analysis, materials, system assembly procedure, and government furnished equipment-BTPS. (TFD)

  8. System Synthesis in Preliminary Aircraft Design Using Statistical Methods

    Science.gov (United States)

    DeLaurentis, Daniel; Mavris, Dimitri N.; Schrage, Daniel P.

    1996-01-01

    This paper documents an approach to conceptual and early preliminary aircraft design in which system synthesis is achieved using statistical methods, specifically Design of Experiments (DOE) and Response Surface Methodology (RSM). These methods are employed in order to more efficiently search the design space for optimum configurations. In particular, a methodology incorporating three uses of these techniques is presented. First, response surface equations are formed which represent aerodynamic analyses, in the form of regression polynomials, which are more sophisticated than generally available in early design stages. Next, a regression equation for an Overall Evaluation Criterion is constructed for the purpose of constrained optimization at the system level. This optimization, though achieved in an innovative way, is still traditional in that it is a point design solution. The methodology put forward here remedies this by introducing uncertainty into the problem, resulting in solutions which are probabilistic in nature. DOE/RSM is used for the third time in this setting. The process is demonstrated through a detailed aero-propulsion optimization of a High Speed Civil Transport. Fundamental goals of the methodology, then, are to introduce higher fidelity disciplinary analyses to the conceptual aircraft synthesis and provide a roadmap for transitioning from point solutions to probabilistic designs (and eventually robust ones).

  9. Ultraviolet Free Electron Laser Facility preliminary design report

    Energy Technology Data Exchange (ETDEWEB)

    Ben-Zvi, I. [ed.

    1993-02-01

    This document, the Preliminary Design Report (PDR) for the Brookhaven Ultraviolet Free Electron Laser (UV FEL) facility, describes all the elements of a facility proposed to meet the needs of a research community which requires ultraviolet sources not currently available as laboratory based lasers. Further, for these experiments, the requisite properties are not extant in either the existing second or upcoming third generation synchrotron light sources. This document is the result of our effort at BNL to identify potential users, determine the requirements of their experiments, and to design a facility which can not only satisfy the existing need, but have adequate flexibility for possible future extensions as need dictates and as evolving technology allows. The PDR is comprised of three volumes. In this, the first volume, background for the development of the proposal is given, including descriptions of the UV FEL facility, and representative examples of the science it was designed to perform. Discussion of the limitations and potential directions for growth are also included. A detailed description of the facility design is then provided, which addresses the accelerator, optical, and experimental systems. Information regarding the conventional construction for the facility is contained in an addendum to volume one (IA).

  10. Ultraviolet Free Electron Laser Facility preliminary design report

    Energy Technology Data Exchange (ETDEWEB)

    Ben-Zvi, I. (ed.)

    1993-02-01

    This document, the Preliminary Design Report (PDR) for the Brookhaven Ultraviolet Free Electron Laser (UV FEL) facility, describes all the elements of a facility proposed to meet the needs of a research community which requires ultraviolet sources not currently available as laboratory based lasers. Further, for these experiments, the requisite properties are not extant in either the existing second or upcoming third generation synchrotron light sources. This document is the result of our effort at BNL to identify potential users, determine the requirements of their experiments, and to design a facility which can not only satisfy the existing need, but have adequate flexibility for possible future extensions as need dictates and as evolving technology allows. The PDR is comprised of three volumes. In this, the first volume, background for the development of the proposal is given, including descriptions of the UV FEL facility, and representative examples of the science it was designed to perform. Discussion of the limitations and potential directions for growth are also included. A detailed description of the facility design is then provided, which addresses the accelerator, optical, and experimental systems. Information regarding the conventional construction for the facility is contained in an addendum to volume one (IA).

  11. Touchstone: Exploratory Design of Experiments

    OpenAIRE

    2007-01-01

    International audience; Touchstone is an open-source experiment design platform designed to help establish a solid research foundation for HCI in the area of novel interaction techniques. Touchstone includes a design platform for exploring alternative designs of controlled laboratory experiments, a run platform for running subjects and a limited analysis platform for advice and access to on-line statistics packages. Designed for HCI researchers and their students, Touchstone facilitates the p...

  12. Spatial experiences and interaction design

    DEFF Research Database (Denmark)

    Dalsgård, Peter

    2006-01-01

    IT is rapidly spreading to non-desktop environments, and is increasingly being used for post-functional purposes. Recent contributions within the field of interaction design have indicated a tight coupling between physico-spatial and experiential issues, both on a technological and on a theoretical...... level. However, interaction design and HCI yet has little to offer designers working with physico-spatial and experiential issues in practical design cases. In this paper, I argue that experiments that explore spatial and experiential aspects are crucial in developing the practice of interaction design....... These  aspects may be brought to the forefront by engaging in, reflecting upon, and reporting from physico-spatial design experiments, and by making spatial and experience-oriented design representations part of the design process. These experiments may be supported by design representations inspired...

  13. Preliminary experiments on quantification of skin condition

    Science.gov (United States)

    Kitajima, Kenzo; Iyatomi, Hitoshi

    2014-03-01

    In this study, we investigated a preliminary assessment method for skin conditions such as a moisturizing property and its fineness of the skin with an image analysis only. We captured a facial images from volunteer subjects aged between 30s and 60s by Pocket Micro (R) device (Scalar Co., Japan). This device has two image capturing modes; the normal mode and the non-reflection mode with the aid of the equipped polarization filter. We captured skin images from a total of 68 spots from subjects' face using both modes (i.e. total of 136 skin images). The moisture-retaining property of the skin and subjective evaluation score of the skin fineness in 5-point scale for each case were also obtained in advance as a gold standard (their mean and SD were 35.15 +/- 3.22 (μS) and 3.45 +/- 1.17, respectively). We extracted a total of 107 image features from each image and built linear regression models for estimating abovementioned criteria with a stepwise feature selection. The developed model for estimating the skin moisture achieved the MSE of 1.92 (μS) with 6 selected parameters, while the model for skin fineness achieved that of 0.51 scales with 7 parameters under the leave-one-out cross validation. We confirmed the developed models predicted the moisture-retaining property and fineness of the skin appropriately with only captured image.

  14. Preliminary Observations from the 2014 Sand Dunes Experiment

    Science.gov (United States)

    2014-10-01

    2014 Sand Dunes Experiment by Christopher W. Miller, Ching-Sang Chiu, D. Benjamin Reeder, Ying-Jang Yang, Linus Chiu, and Chi-Fang Chen...COVERED (From-To) June 2014 4. TITLE AND SUBTITLE Preliminary Observations from the 2014 Sand Dunes Experiment 5a. CONTRACT NUMBER 5b. GRANT NUMBER...position of the Department of Defense or the U.S. Government 14. ABSTRACT The Sand Dunes 2014 experiment was international US – Taiwan

  15. Preliminary results of noise radar experiments

    Science.gov (United States)

    Malanowski, Mateusz; Contartese, Clara; Maslikowski, Lukasz; Baczyk, Marcin; Kulpa, Krzysztof

    2009-06-01

    The paper describes the first results of noise radar experiments carried out at Warsaw University of Technology. The radar system was built with Commercial Off-The-Shelf (COTS) components: log-periodic antennas, an arbitrary waveform generator and a two-channel spectrum analyzer. The radar operated in the continuous-wave mode, and the aim was to detect moving targets in the received signal. The paper shows the system setup as well as the numerical results obtained from the recorded signals.

  16. Underwater Munitions Expert System: Preliminary Design Report

    Science.gov (United States)

    2015-08-21

    coral   reefs ,  can  be  added  to  future  versions  of  UnMES.     For  this  preliminary  UnMES...administer  areas   polluted  by  discarded  munitions.    Towards  this  end,  SERDP  is   sponsoring   the   development...estimating   seawater   pollution   from   dissolved   chemical   components  of  munitions.    

  17. Metabolic Control with Insulin Pump Therapy: Preliminary Experience

    Directory of Open Access Journals (Sweden)

    Shang-Ren Hsu

    2008-07-01

    Conclusion: Our preliminary experience demonstrated the effectiveness of insulin pump therapy for both type 1 and type 2 diabetic patients. The reduction in their HbA1C values was both statistically and clinically significant. This treatment should be considered for patients poorly controlled by subcutaneous insulin injection therapy.

  18. Structural Assembly Demonstration Experiment (SADE) experiment design

    Science.gov (United States)

    Akin, D. L.; Bowden, M. L.

    1982-03-01

    The Structural Assembly Demonstration Experiment concept is to erect a hybrid deployed/assembled structure as an early space experiment in large space structures technology. The basic objectives can be broken down into three generic areas: (1) by performing assembly tasks both in space and in neutral buoyancy simulation, a mathematical basis will be found for the validity conditions of neutral buoyancy, thus enhancing the utility of water as a medium for simulation of weightlessness; (2) a data base will be established describing the capabilities and limitations of EVA crewmembers, including effects of such things as hardware size and crew restraints; and (3) experience of the M.I.T. Space Systems Lab in neutral buoyancy simulation of large space structures assembly indicates that the assembly procedure may create the largest loads that a structure will experience during its lifetime. Data obtained from the experiment will help establish an accurate loading model to aid designers of future space structures.

  19. Preliminary design package for prototype solar heating and cooling systems

    Science.gov (United States)

    1978-01-01

    A summary is given of the preliminary analysis and design activity on solar heating and cooling systems. The analysis was made without site specific data other than weather; therefore, the results indicate performance expected under these special conditions. Major items include a market analysis, design approaches, trade studies and other special data required to evaluate the preliminary analysis and design. The program calls for the development and delivery of eight prototype solar heating and cooling systems for installation and operational test. Two heating and six heating and cooling units will be delivered for Single Family Residences, Multiple-family Residences and commercial applications.

  20. Preliminary design review report - sludge offload system

    Energy Technology Data Exchange (ETDEWEB)

    Mcwethy, L.M. Westinghouse Hanford

    1996-06-05

    This report documents the conceptual design review of the sludge offload system for the Spent Nuclear Fuel Project. The design description, drawings, available analysis, and safety analysis were reviewed by a peer group. The design review comments and resolutions are documented.

  1. Preliminary results of the echo-seeding experiment at SLAC

    Energy Technology Data Exchange (ETDEWEB)

    Xiang, D.; Colby, E.; Ding, Y.; Dunning, M.; Frederico, J.; Gilevich, S.; Hast, C.; Jobe, K.; McCormick, D.; Nelson, J.; Raubenheimer, T.O.; Soong, K.; Stupakov, G.; Szalata, Z.; Walz, D.; Weathersby, S.; Woodley, M.; Corlett, J.; Qiang, J.; Penn, G.; Prestemon, S.; Schlueter, R.; Venturini, M.; Wan, W.; Pernet, P-L.

    2010-05-23

    ECHO-7 is a proof-of-principle echo-enabled harmonic generation FEL experiment in the Next Linear Collider Test Accelerator (NLCTA) at SLAC. The experiment aims to generate coherent radiation at 318 nm and 227 nm, which are the 5th and 7th harmonic of the infrared seed laser. In this paper we present the preliminary results from the commissioning run of the completed experimental setup which started in April 2010.

  2. Thermal energy storage in aquifiers: preliminary information

    Energy Technology Data Exchange (ETDEWEB)

    Allen, R.D.

    1979-12-01

    Topics discussed include: conceptual designs; numerical modelling; field experiments; relevant technical information; feasibility studies; preliminary aquifer selection considerations; and preliminary design and operating considerations. (TFD)

  3. Preliminary Design of a Femtosecond Oscilloscope

    CERN Document Server

    Gazazyan, Edmond D; Kalantaryan, Davit K; Laziev, Edouard; Margaryan, Amour

    2005-01-01

    The calculations on motion of electrons in a finite length electromagnetic field of linearly and circularly polarized laser beams have shown that one can use the transversal deflection of electrons on a screen at a certain distance after the interaction region for the measurement of the length and longitudinal particle distribution of femtosecond bunches. In this work the construction and preliminary parameters of various parts of a device that may be called femtosecond oscilloscope are considered. The influence of various factors, such as the energy spread and size of the electron bunches, are taken into account. For CO2 laser intensity 1016 W/cm2 and field free drift length 1m the deflection is 5.3 and 0.06 cm, while the few centimeters long interaction length between 2 mirrors requires assembling accuracy 6 mm and 1.3 micron for 20 MeV to 50 keV, respectively.

  4. TPX: Contractor preliminary design review. Volume 3, Design and analysis

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-30

    Several models have been formed for investigating the maximum electromagnetic loading and magnetic field levels associated with the Tokamak Physics eXperiment (TPX) superconducting Poloidal Field (PF) coils. The analyses have been performed to support the design of the individual fourteen hoop coils forming the PF system. The coils have been sub-divided into three coil systems consisting of the central solenoid (CS), PF5 coils, and the larger radius PF6 and PF7 coils. Various electromagnetic analyses have been performed to determine the electromagnetic loadings that the coils will experience during normal operating conditions, plasma disruptions, and fault conditions. The loadings are presented as net body forces acting individual coils, spatial variations throughout the coil cross section, and force variations along the path of the conductor due to interactions with the TF coils. Three refined electromagnetic models of the PF coil system that include a turn-by-turn description of the fields and forces during a worst case event are presented in this report. A global model including both the TF and PF system was formed to obtain the force variations along the path of the PF conductors resulting from interactions with the TF currents. In addition to spatial variations, the loadings are further subdivided into time-varying and steady components so that structural fatigue issues can be addressed by designers and analysts. Other electromagnetic design issues such as the impact of the detailed coil designs on field errors are addressed in this report. Coil features that are analyzed include radial transitions via short jogs vs. spiral type windings and the effects of layer-to-layer rotations (i.e clocking) on the field errors.

  5. Percutaneous aspiration thromboembolectomy: a preliminary experience.

    Science.gov (United States)

    Murray, J G; Brown, A L; Wilkins, R A

    1994-08-01

    Percutaneous aspiration thromboembolectomy (PAT) is a radiological alternative to surgical embolectomy or thrombolysis in the treatment of acute arterial thromboembolic disease. We report our experience in eight patients aged 63-83 years (mean 71 years). Indications were graft thrombosis (1) or emboli from atrial fibrillation (3), abdominal aneurysm (2) or proximal angioplasty (2). PAT was performed at 10 arterial sites; common iliac (1), profunda femoris (1), superficial femoral (2), femoro-popliteal graft (1), popliteal (2) and arteries of the trifurcation (3). PAT was used as an adjunct to thrombolysis or angioplasty in five patients and as the sole procedure in three patients. It was successful in six patients (seven sites) with mean ABI rising from 0.4 pre- to 0.8 post-procedure. Two of the failures required amputations. One of these was a completely thrombosed dacron femoro-popliteal graft with poor run-off, and the second case had a failed surgical embolectomy prior to amputation. There were no major complications, and no mortality on follow-up at 1 month. PAT is a useful adjunct to thrombolysis and balloon angioplasty in the radiological treatment of acute thromboembolic disease. In patients in whom thrombolysis is contraindicated, it offers an alternative to surgical embolectomy.

  6. Designing experiments through compressed sensing.

    Energy Technology Data Exchange (ETDEWEB)

    Young, Joseph G.; Ridzal, Denis

    2013-06-01

    In the following paper, we discuss how to design an ensemble of experiments through the use of compressed sensing. Specifically, we show how to conduct a small number of physical experiments and then use compressed sensing to reconstruct a larger set of data. In order to accomplish this, we organize our results into four sections. We begin by extending the theory of compressed sensing to a finite product of Hilbert spaces. Then, we show how these results apply to experiment design. Next, we develop an efficient reconstruction algorithm that allows us to reconstruct experimental data projected onto a finite element basis. Finally, we verify our approach with two computational experiments.

  7. Preliminary ALARA design concept for SMART

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kyo Youn; Kim, Seung Nam; Kim, Ha Yong; Zee, Sung Quun; Chang, Moon Hee

    1999-03-01

    SMART(System-integrated Modular Advanced ReacTor) is a space saving integral type nuclear rector with the thermal power of 330 MW. This report provides general design guide and authority in NSSS designs for SMART needed to maintain the occupational doses and doses to members of public ALARA to meet the regulatory requirements. Paragraph 20.1 of 10 CFR 20, ''Standards for Protection Against Radiation'', states that licensee should make every reasonable effort to maintain exposures to radiation as far below the limits specified in Part 20 as is reasonably achievable. The ALARA (as low as is reasonably achievable) principle is incorporated into Korean radiation protection law as paragraph one Article 97 of the Atomic Energy Act. (Jan. 1995). This ALARA Design Concept for SMART provides 1) description of the organization and responsibilities needed for upper level management support and authority in order for the implementation of ALARA, 2) guidance and procedures for design, review, and evaluation needed for SMART ALARA program implementation, 3) general design guidelines for SMART NSSS and BOP designers to implement ALARA principles in design stage, and 4) training and instruction requirement of SMART NSSS and BOP designers for the familiarization of ALARA principles to be implemented in NSSS designs. (Author). 4 refs., 1 tabs.

  8. Introduction to Statistically Designed Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Heaney, Mike

    2016-09-13

    Statistically designed experiments can save researchers time and money by reducing the number of necessary experimental trials, while resulting in more conclusive experimental results. Surprisingly, many researchers are still not aware of this efficient and effective experimental methodology. As reported in a 2013 article from Chemical & Engineering News, there has been a resurgence of this methodology in recent years (http://cen.acs.org/articles/91/i13/Design-Experiments-Makes-Comeback.html?h=2027056365). This presentation will provide a brief introduction to statistically designed experiments. The main advantages will be reviewed along with the some basic concepts such as factorial and fractional factorial designs. The recommended sequential approach to experiments will be introduced and finally a case study will be presented to demonstrate this methodology.

  9. Preliminary Design of IHTS Cold Trap for PGSFR

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jewhan; Lee, Taeho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    The main impurities in liquid sodium of the IHTS are oxygen and hydrogen. These impurities form oxides and hydrides with sodium and cause various problems. In order to eliminate the impurities the Cold Trap is installed in the loop. The life and capacity of the IHTS cold Trap depends the amount of impurities. For IHTS loop, the hydrogen has been identified as the major contamination from Steam Generator (SG) during the normal operation. In this study, the sizing of cold trap based on the source rate of hydrogen from SG from past experiences was conducted. Empirical relations among different variables were adopted to establish the temperature distribution, pressure drops, flow rates and geometries for the cold trap and its associated component. In this study, the IHTS cold trap for normal operation has been analyzed and the preliminary design of corresponding cold trap and economizer has been carried out. For further detailed design, R and D on basic sodium technology will be essential to optimize the Cold Trap.

  10. Multidisciplinary Optimization Methods for Aircraft Preliminary Design

    Science.gov (United States)

    Kroo, Ilan; Altus, Steve; Braun, Robert; Gage, Peter; Sobieski, Ian

    1994-01-01

    This paper describes a research program aimed at improved methods for multidisciplinary design and optimization of large-scale aeronautical systems. The research involves new approaches to system decomposition, interdisciplinary communication, and methods of exploiting coarse-grained parallelism for analysis and optimization. A new architecture, that involves a tight coupling between optimization and analysis, is intended to improve efficiency while simplifying the structure of multidisciplinary, computation-intensive design problems involving many analysis disciplines and perhaps hundreds of design variables. Work in two areas is described here: system decomposition using compatibility constraints to simplify the analysis structure and take advantage of coarse-grained parallelism; and collaborative optimization, a decomposition of the optimization process to permit parallel design and to simplify interdisciplinary communication requirements.

  11. Preliminary conceptual design of DEMO EC system

    Energy Technology Data Exchange (ETDEWEB)

    Garavaglia, S., E-mail: garavaglia@ifp.cnr.it; Bin, W.; Bruschi, A.; Granucci, G.; Moro, A.; Rispoli, N. [Institute of Plasma Physics “P.Caldirola”, National Research Council of Italy, Milan (Italy); Grossetti, G.; Strauss, D. [IAM-AWP, Kaiserstr. 12, D-76131 Karlsruhe (Germany); Jelonnek, J. [IHM, KIT, Kaiserstr. 12, D-76131 Karlsruhe (Germany); Tran, Q. M. [CRPP, EPFL, EURATOM Association, CH-1015 Lausanne (Switzerland); Franke, T. [EUROfusion Consortium, Boltzmannstr. 2, D-85748 Garching (Germany); Max-Planck-Institut für Plasmaphysik, Garching (Germany)

    2015-12-10

    In the framework of EUROfusion Consortium the Work Package Heating and Current Drive addresses the engineering design and R&D for the electron cyclotron, ion cyclotron and neutral beam systems. This paper reports the activities performed in 2014, focusing on the work done regarding the input for the conceptual design of the EC system, particularly for the gyrotron, the transmission line and the launchers.

  12. RELIABILITY AND DESIGN OF EXPERIMENTS

    Directory of Open Access Journals (Sweden)

    Adrian Stere PARIS

    2013-05-01

    Full Text Available The mechanical reliability uses many statistical tools to find the factors of influence and their levels inthe optimization of parameters on the basis of experimental data. Design of Experiments (DOE techniquesenables designers to determine simultaneously the individual and interactive effects of many factors that couldaffect the output results in any design. The state-of-the-art in the domain implies extended use of software and abasic mathematical knowledge, mainly applying ANOVA and the regression analysis of experimental data.

  13. Preliminary Conceptual Design for Safety Parameter display System of PGSFR

    Energy Technology Data Exchange (ETDEWEB)

    Jo, Hyunju; Seong, Seunghwan; Kim, Wansu; Kim, Donghoon; Son, Kwangseop; Jang, Gwisook [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    A PGSFR (prototype Gen-IV sodium-cooled fast reactor) is under development at KAERI. A safety parameter display system (SPDS) should be designed for licensing the PGSFR in order to cope with the TMI action plan requirements. Thus, a preliminary conceptual design for the SPDS of PGSFR including licensing requirements, intrinsic function, critical variables and alarm legs for the SPDS of the PGSFR is studied herein. At first, some documents issued by NRC related to install a SPDS include the following: - NUREG-0737, Clarification of TMI Action Plan Requirements - NUREG-0696, Functional Criteria for Emergency Response Facilities - NUREG-0835, Human Factors Acceptance Criteria for the Safety Parameter display System, Draft Report for Comment. The preliminary concept design for the SPDS of the PGSFR was studied. In designing of the PGSFR, the studied design concept will be refined and implemented through further studies to acquire the approval of a safety analysis report of the PGSFR.

  14. A decision support system for preliminary design

    NARCIS (Netherlands)

    Groot, E.H. de; Mallory, S.M.; Zutphen, R.H.M. van; Vries, B. de

    1999-01-01

    The design of buildings is a complex task for a variety of reasons. In the conceptual stage, particularly in the inception phase, a small number of people make decisions that have far reaching impact on the final result in terms of efficiency and effectiveness. Decision-making in the inception phase

  15. Aeroelastic Considerations in the Preliminary Design Aircraft

    Science.gov (United States)

    1983-09-01

    DESIGN OBJECTIVES FEM FASO MODELINGWEGS TRNFRAIS SIZING RIGID AtP .FIRST FIRST FLEX FIRST FLEXSTATICLOADS [ IZING STATIC LOADS SIZING UPDATEFLEX SIZING...Structural Optimization by ASAT A computer software system called ASAT (Automatische Struktur Auslegung von Trag- flchen) exists at MBB which allows

  16. A decision support system for preliminary design

    NARCIS (Netherlands)

    Groot, E.H. de; Mallory, S.M.; Zutphen, R.H.M. van; Vries, B. de

    1999-01-01

    The design of buildings is a complex task for a variety of reasons. In the conceptual stage, particularly in the inception phase, a small number of people make decisions that have far reaching impact on the final result in terms of efficiency and effectiveness. Decision-making in the inception phase

  17. Design and analysis of experiments

    CERN Document Server

    Dean, Angela; Draguljić, Danel

    2017-01-01

    This textbook takes a strategic approach to the broad-reaching subject of experimental design by identifying the objectives behind an experiment and teaching practical considerations that govern design and implementation, concepts that serve as the basis for the analytical techniques covered. Rather than a collection of miscellaneous approaches, chapters build on the planning, running, and analyzing of simple experiments in an approach that results from decades of teaching the subject. In most experiments, the procedures can be reproduced by readers, thus giving them a broad exposure to experiments that are simple enough to be followed through their entire course. Outlines of student and published experiments appear throughout the text and as exercises at the end of the chapters. The authors develop the theory of estimable functions and analysis of variance with detail, but at a mathematical level that is simultaneously approachable. Throughout the book, statistical aspects of analysis complement practical as...

  18. Design Preliminaries for Direct Drive under Water Wind Turbine Generator

    DEFF Research Database (Denmark)

    Leban, Krisztina Monika; Ritchie, Ewen; Argeseanu, Alin

    2012-01-01

    This paper focuses on the preliminary design process of a 20 MW electric generator. The application calls for an offshore, vertical axis, direct drive wind turbine. Arguments for selecting the type of electric machine for the application are presented and discussed. Comparison criteria for deciding...

  19. Preliminary Tritium Management Design Activities at ORNL

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, Thomas J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Felde, David K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Logsdon, Randall J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); McFarlane, Joanna [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Qualls, A. L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-09-01

    Interest in salt-cooled and salt-fueled reactors has increased over the last decade (Forsberg et al. 2016). Several private companies and universities in the United States, as well as governments in other countries, are developing salt reactor designs and/or technology. Two primary issues for the development and deployment of many salt reactor concepts are (1) the prevention of tritium generation and (2) the management of tritium to prevent release to the environment. In 2016, the US Department of Energy (DOE) initiated a research project under the Advanced Reactor Technology Program to (1) experimentally assess the feasibility of proposed methods for tritium mitigation and (2) to perform an engineering demonstration of the most promising methods. This document describes results from the first year’s efforts to define, design, and build an experimental apparatus to test potential methods for tritium management. These efforts are focused on producing a final design document as the basis for the apparatus and its scheduled completion consistent with available budget and approvals for facility use.

  20. Preliminary design data package, appendix C. [hybrid electric vehicles

    Science.gov (United States)

    1979-01-01

    The data and documentation required to define the preliminary design of a near term hybrid vehicle and to quantify its operational characteristics are presented together with the assumptions and rationale behind the design decisions. Aspects discussed include development requirements for the propulsion system, the chassis system, the body, and the vehicle systems. Particular emphasis is given to the controls, the heat engine, and the batteries.

  1. Preliminary Thermal Design of Cryogenic Radiation Shielding

    Science.gov (United States)

    Li, Xiaoyi; Mustafi, Shuvo; Boutte, Alvin

    2015-01-01

    Cryogenic Hydrogen Radiation Shielding (CHRS) is the most mass efficient material radiation shielding strategy for human spaceflight beyond low Earth orbit (LEO). Future human space flight, mission beyond LEO could exceed one year in duration. Previous radiation studies showed that in order to protect the astronauts from space radiation with an annual allowable radiation dose less than 500 mSv, 140 kgm2 of polyethylene is necessary. For a typical crew module that is 4 meter in diameter and 8 meter in length. The mass of polyethylene radiation shielding required would be more than 17,500 kg. The same radiation study found that the required hydrogen shielding for the same allowable radiation dose is 40 kgm2, and the mass of hydrogen required would be 5, 000 kg. Cryogenic hydrogen has higher densities and can be stored in relatively small containment vessels. However, the CHRS system needs a sophisticated thermal system which prevents the cryogenic hydrogen from evaporating during the mission. This study designed a cryogenic thermal system that protects the CHRS from hydrogen evaporation for one to up to three year mission. The design also includes a ground based cooling system that can subcool and freeze liquid hydrogen. The final results show that the CHRS with its required thermal protection system is nearly half of the mass of polyethylene radiation shielding.

  2. Preliminary Mechanical Design of FHX for PGSFR

    Energy Technology Data Exchange (ETDEWEB)

    Choo, Jinyup; Koo, G. H.; Kim, S. K. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    In this paper, more specific data from analysis and mechanical method of approach to design will be addressed. Especially, frame of tube bundle and housing of FHX. Heretofore, it is concept design by mechanical basic knowledge and research of various structures that are activating in realities. Especially, to reduce thermal stress, we have planning to attach insulations inside the housing. In as much as FHX is as important on SFR as the other part, hereafter, we will develop FEM to check feasibility of the FHX's housing design in order to perform static and thermal analysis as well as bucking, seismic and so on. The Forced-draft sodium-to-air Heat Exchanger system (FHX) (employed in the Active Decay Heat Removal System (ADHRS) is a shell-and-tube type counter-current flow heat exchanger with serpentine finned-tube arrangement. Liquid sodium flows over the finned tubes. The unit is placed above the reactor building and has function of dumping the system heat load into the final heat sink, i. e., the atmosphere. Heat is transmitted from the primary hot sodium pool into the ADHRS sodium loop via Decay Heat Exchanger (DHX), and a direct heat exchange occurs between the tube-side sodium and the shell-side air through the FHX sodium tube wall. Cold atmospheric air is introduced into the air inlet duct at the lower part of the unit by using an electrically driven air blower. Air flows across the finned tube bank rising upward direction to make uniform air flow with perfect mixing across the tubes. The finned tube bundle is placed inside a well-insulated casing. The air heated at the tube bank region is collected at the top of the unit and then is discharged through the air stack above the unit. Although a blower supplies atmospheric air into the FHX unit, a tall air stack is also provided to secure natural draft head of natural circulation air flow against a loss power supply. The stack also has rain protecting structures to prevent inflow of rain drops or undesired

  3. A preliminary design of a knot undulator.

    Science.gov (United States)

    Xi, Fuchun; Shi, Tan; Fan, Qingyan; Prestemon, Soren; Wan, Weishi; An, Zhenghua; Qiao, S

    2013-01-01

    The magnetic field configuration of the previously proposed knot undulator [Qiao et al. (2009). Rev. Sci. Instrum. 80, 085108] is realised in the design of a hybridized elliptically polarized undulator, which is presented. Although the details of the field distribution are not the same as those in the theoretical proposal, it is demonstrated that the practical knot undulator could work perfectly. In order to understand the minor discrepancies of the two, mathematical formulae of the synchrotron radiation are derived based on the Fourier transform of the magnetic field. From the results of calculations by simulation program, the discrepancies could be well interpreted by the corresponding formulae. The results show the importance of optimization of the end sections of the knot undulator to suppress the on-axis heat load. Furthermore, a study of the impact of the undulator on beam dynamics of the storage ring was conducted using the Shanghai Synchrotron Radiation Facility as an example and the results show that the knot undulator has little effect on the beam.

  4. Preliminary design report for OTEC stationkeeping subsystems (SKSS)

    Energy Technology Data Exchange (ETDEWEB)

    1979-12-12

    Lockheed Ocean Systems with IMODCO prepared these preliminary designs for OTEC Stationkeeping Subsystems (SKSS) under contract to NOAA in support of the Department of Energy OTEC program. The results of Tasks III, V, and VI are presented in this design report. The report consists of five sections: introduction, preliminary designs for the multiple anchor leg (MAL) and tension anchor leg (TAL), costs and schedule, and conclusions. Extensive appendixes provide detailed descriptions of design methodology and include backup calculations and data to support the results presented. The objective of this effort is to complete the preliminary designs for the barge-MAL and Spar-TAL SKSS. A set of drawings is provided for each which show arrangements, configuration, component details, engineering description, and deployment plan. Loads analysis, performance assessment, and sensitivity to requirements are presented, together with the methodology employed to analyze the systems and to derive the results presented. Life cycle costs and schedule are prepared and compared on a common basis. Finally, recommendations for the Commercial Plant SKSS are presented for both platform types.

  5. Design analysis for grounding experiments

    NARCIS (Netherlands)

    Lemmen, P.P.M.; Vredeveldt, A.W.; Pinkster, J.A.

    1996-01-01

    In 1995 a series of six grounding experiments has been carried out with a 600 Tonne inland water way tanker. At the how of the vessel test sections could be fitted, which were run into an artificial rock. The design of the support structures for the test sections and for the rock required the predic

  6. Participatory design of a preliminary safety checklist for general practice.

    Science.gov (United States)

    Bowie, Paul; Ferguson, Julie; MacLeod, Marion; Kennedy, Susan; de Wet, Carl; McNab, Duncan; Kelly, Moya; McKay, John; Atkinson, Sarah

    2015-05-01

    The use of checklists to minimise errors is well established in high reliability, safety-critical industries. In health care there is growing interest in checklists to standardise checking processes and ensure task completion, and so provide further systemic defences against error and patient harm. However, in UK general practice there is limited experience of safety checklist use. To identify workplace hazards that impact on safety, health and wellbeing, and performance, and codesign a standardised checklist process. Application of mixed methods to identify system hazards in Scottish general practices and develop a safety checklist based on human factors design principles. A multiprofessional 'expert' group (n = 7) and experienced front-line GPs, nurses, and practice managers (n = 18) identified system hazards and developed and validated a preliminary checklist using a combination of literature review, documentation review, consensus building workshops using a mini-Delphi process, and completion of content validity index exercise. A prototype safety checklist was developed and validated consisting of six safety domains (for example, medicines management), 22 sub-categories (for example, emergency drug supplies) and 78 related items (for example, stock balancing, secure drug storage, and cold chain temperature recording). Hazards in the general practice work system were prioritised that can potentially impact on the safety, health and wellbeing of patients, GP team members, and practice performance, and a necessary safety checklist prototype was designed. However, checklist efficacy in improving safety processes and outcomes is dependent on user commitment, and support from leaders and promotional champions. Although further usability development and testing is necessary, the concept should be of interest in the UK and internationally. © British Journal of General Practice 2015.

  7. Design of satellite flexibility experiments

    Science.gov (United States)

    Kaplan, M. H.; Hillard, S. E.

    1977-01-01

    A preliminary study has been completed to begin development of a flight experiment to measure spacecraft control/flexible structure interaction. The work reported consists of two phases: identification of appropriate structural parameters which can be associated with flexibility phenomena, and suggestions for the development of an experiment for a satellite configuration typical of near-future vehicles which are sensitive to such effects. Recommendations are made with respect to the type of data to be collected and instrumentation associated with these data. The approach consists of developing the equations of motion for a vehicle possessing a flexible solar array, then linearizing about some nominal motion of the craft. A set of solutions are assumed for array deflection using a continuous normal mode method and important parameters are exposed. Inflight and ground based measurements are distinguished. Interrelationships between these parameters, measurement techniques, and input requirements are discussed which assure minimization of special vehicle maneuvers and optimization of data to be obtained during the normal flight sequence.

  8. Gemini Planet Imager: Preliminary Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Macintosh, B

    2007-05-10

    completely limited by quasi-static wave front errors, so that contrast does not improve with integration times longer than about 1 minute. Using the rotation of the Earth to distinguish companions from artifacts or multiwavelength imaging improves this somewhat, but GPI will still need to surpass the performance of existing systems by one to two orders of magnitude--an improvement comparable to the transition from photographic plates to CCDs. This may sound daunting, but other areas of optical science have achieved similar breakthroughs, for example, the transition to nanometer-quality optics for extreme ultraviolet lithography, the development of MEMS wave front control devices, and the ultra-high contrast demonstrated by JPL's High Contrast Imaging Test-bed. In astronomy, the Sloan Digital Sky Survey, long baseline radio interferometry, and multi-object spectrographs have led to improvements of similar or greater order of magnitude. GPI will be the first project to apply these revolutionary techniques to ground-based astronomy, with a systems engineering approach that studies the impact of every design decision on the key metric--final detectable planet contrast.

  9. The RPC-based IFR system at BaBar experiment preliminary results

    CERN Document Server

    Piccolo, D; Bagnasco, S; Baldini, R; Band, H R; Bionta, R; Buzzo, A; Calcaterra, A; Cavallo, N; Contri, R; Crosetti, G; De Nardo, Gallieno; De Sangro, R; Fabozzi, F; Falciai, D; Finocchiaro, G; Gatto, C; Johnson, J; Lista, L; Lo Vetere, M; Macri, M; Monge, R; Palano, A; Paolucci, P; Passaggio, S; Patrignani, C; Patteri, P; Peruzzi, I; Piccolo, M; Robutti, E; Santroni, A; Sciacca, C; Wright, D; Yu, Z; Zallo, A

    2002-01-01

    The IFR system is a RPC-based detector used to identify muons and neutral hadrons in the BaBar experiment at PEP II machine in SLAC. The RPC system can be used to reconstruct the trajectory of muons, pions and neutral hadrons interacting in the iron of the IFR. The different range and hit pattern allow to discriminate different particles crossing the IFR. An overview of the system design and the preliminary results on the IFR performances are reported.

  10. Variant Designing in the Preliminary Small Ship Design Process

    Directory of Open Access Journals (Sweden)

    Karczewski Artur

    2017-06-01

    Full Text Available Ship designing is a complex process, as the ship itself is a complex, technical multi-level object which operates in the air/water boundary environment and is exposed to the action of many different external and internal factors resulting from the adopted technical solutions, type of operation, and environmental conditions. A traditional ship design process consists of a series of subsequent multistage iterations, which gradually increase the design identification level. The paper presents problems related to the design of a small untypical vessel with the aid of variant methodology making use of optimisation algorithms. The computer-aided design methodology has been developed which does not need permanent reference to already built real ships and empirical-statistical relations. Possibilities were indicated for integrating together early design stages, and parallel designing of hull shape and parameters.

  11. Preliminary Design Report for the Yakima/Klickitat Production Project.

    Energy Technology Data Exchange (ETDEWEB)

    US Bonneville Power Administration

    1990-04-01

    A master plan for the Yakima/Klickitat Production Project (YKPP) was developed by the Northwest Power Planning Council (Council) on October 15, 1987, as a reasonable basis upon which the Bonneville Power Administration (BPA) could proceed to fund predesign work on the project. The Council approved the predesign work on the condition that eight preliminary tasks were completed. These tasks are: Task 1. Agreement on a refined statement of project goals. Task 2. Completion of a technical analysis of water supplies. Task 3. Completion of an experimental design plan. Task 4. Development of a harvest management plan. Task 5. Assessment of potential genetic risks. Task 6. Project coordination with all other affected parties. Task 7. Submission of a preliminary design report to the Council. Task 8. Develop a project management structure. The preliminary design report summarizes the work completed on these tasks. It provides a description of the preliminary design, engineering, and construction phases of project development, and gives an estimate of project costs. Also included is a description of other studies that were conducted to support YKPP planning. The results of studies conducted during the last 30 months indicate that hatchery facilities can be built in the Yakima and Klickitat subbasins to provide harvest benefits and to supplement natural production. Planning for the Yakima subbasin is at a more advanced stage of development than for the Klickitat subbasin because of greater availability of basic resource information. The information needed to proceed with final design and construction for the Klickitat subbasin will be available by 1992, as ongoing predesign work continues. This schedule is consistent with the anticipated phased completion of the YKPP by 1997.

  12. Preliminary design of the ITER ECH Upper Launcher

    Energy Technology Data Exchange (ETDEWEB)

    Strauss, D., E-mail: dirk.strauss@kit.edu [Karlsruhe Institute of Technology, Assoc. KIT-EURATOM, D-76021 Karlsruhe (Germany); Aiello, G. [Karlsruhe Institute of Technology, Assoc. KIT-EURATOM, D-76021 Karlsruhe (Germany); Chavan, R. [Centre de Recherches en Physique des Plasmas, CRPP–EPFL, CH-1015 Lausanne (Switzerland); Cirant, S. [Istituto di Fisica del Plasma CNR, Euratom Association, 20125 Milano (Italy); Baar, M. de [FOM, Van Vollenhovenlaan 659, 3527 JP, Utrecht (Netherlands); Farina, D. [Istituto di Fisica del Plasma CNR, Euratom Association, 20125 Milano (Italy); Gantenbein, G. [Karlsruhe Institute of Technology, Assoc. KIT-EURATOM, D-76021 Karlsruhe (Germany); Goodman, T.P. [Centre de Recherches en Physique des Plasmas, CRPP–EPFL, CH-1015 Lausanne (Switzerland); Henderson, M.A. [ITER Organization, 13108 Saint-Paul-lez-Durance (France); Kasparek, W. [Institut für Plasmaforschung, IPF, D-70569 Stuttgart (Germany); Kleefeldt, K. [Karlsruhe Institute of Technology, Assoc. KIT-EURATOM, D-76021 Karlsruhe (Germany); Landis, J.-D. [Centre de Recherches en Physique des Plasmas, CRPP–EPFL, CH-1015 Lausanne (Switzerland); Meier, A. [Karlsruhe Institute of Technology, Assoc. KIT-EURATOM, D-76021 Karlsruhe (Germany); Moro, A.; Platania, P. [Istituto di Fisica del Plasma CNR, Euratom Association, 20125 Milano (Italy); Plaum, B. [Institut für Plasmaforschung, IPF, D-70569 Stuttgart (Germany); Poli, E. [Max-Planck-IPP, Euratom Association, D-85748 Garching (Germany); Ramponi, G. [Istituto di Fisica del Plasma CNR, Euratom Association, 20125 Milano (Italy); Ronden, D. [FOM, Van Vollenhovenlaan 659, 3527 JP, Utrecht (Netherlands); Saibene, G. [Fusion for Energy, Barcelona (Spain); and others

    2013-11-15

    Highlights: • Front steering mirror design. • Plasma facing blanket shield module/first wall panel design. • Fixed frequency torus CVD diamond window serving as first tritium barrier. • Prototypes and tests of the above key components in the Launcher Handling and Testing Facility. -- Abstract: The design of the ITER electron cyclotron launchers recently reached the preliminary design level - the last major milestone before design finalization. The ITER ECH system contains 24 installed gyrotrons providing a maximum ECH injected power of 20 MW through transmission lines towards the tokamak. There are two EC launcher types both using a front steering mirror; one equatorial launcher (EL) for plasma heating and four upper launchers (UL) for plasma mode stabilization (neoclassical tearing modes and the sawtooth instability). A wide steering angle range of the ULs allows focusing of the beam on magnetic islands which are expected on the rational magnetic flux surfaces q = 1 (sawtooth instability), q = 3/2 and q = 2 (NTMs). In this paper the preliminary design of the ITER ECH UL is presented, including the optical system and the structural components. Highlights of the design include the torus CVD-diamond windows, the frictionless, front steering mechanism and the plasma facing blanket shield module (BSM). Numerical simulations as well as prototype tests are used to verify the design.

  13. Preliminary design study of the TMT Telescope structure system: overview

    Science.gov (United States)

    Usuda, Tomonori; Ezaki, Yutaka; Kawaguchi, Noboru; Nagae, Kazuhiro; Kato, Atsushi; Takaki, Junji; Hirano, Masaki; Hattori, Tomoya; Tabata, Masaki; Horiuchi, Yasushi; Saruta, Yusuke; Sofuku, Satoru; Itoh, Noboru; Oshima, Takeharu; Takanezawa, Takashi; Endo, Makoto; Inatani, Junji; Iye, Masanori; Sadjadpour, Amir; Sirota, Mark; Roberts, Scott; Stepp, Larry

    2014-07-01

    We present an overview of the preliminary design of the Telescope Structure System (STR) of Thirty Meter Telescope (TMT). NAOJ was given responsibility for the TMT STR in early 2012 and engaged Mitsubishi Electric Corporation (MELCO) to take over the preliminary design work. MELCO performed a comprehensive preliminary design study in 2012 and 2013 and the design successfully passed its Preliminary Design Review (PDR) in November 2013 and April 2014. Design optimizations were pursued to better meet the design requirements and improvements were made in the designs of many of the telescope subsystems as follows: 1. 6-legged Top End configuration to support secondary mirror (M2) in order to reduce deformation of the Top End and to keep the same 4% blockage of the full aperture as the previous STR design. 2. "Double Lower Tube" of the elevation (EL) structure to reduce the required stroke of the primary mirror (M1) actuators to compensate the primary mirror cell (M1 Cell) deformation caused during the EL angle change in accordance with the requirements. 3. M1 Segment Handling System (SHS) to be able to make removing and installing 10 Mirror Segment Assemblies per day safely and with ease over M1 area where access of personnel is extremely difficult. This requires semi-automatic sequence operation and a robotic Segment Lifting Fixture (SLF) designed based on the Compliance Control System, developed for controlling industrial robots, with a mechanism to enable precise control within the six degrees of freedom of position control. 4. CO2 snow cleaning system to clean M1 every few weeks that is similar to the mechanical system that has been used at Subaru Telescope. 5. Seismic isolation and restraint systems with respect to safety; the maximum acceleration allowed for M1, M2, tertiary mirror (M3), LGSF, and science instruments in 1,000 year return period earthquakes are defined in the requirements. The Seismic requirements apply to any EL angle, regardless of the

  14. NRT Rotor Structural / Aeroelastic Analysis for the Preliminary Design Review

    Energy Technology Data Exchange (ETDEWEB)

    Ennis, Brandon Lee [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Paquette, Joshua A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-10-01

    This document describes the initial structural design for the National Rotor Testbed blade as presented during the preliminary design review at Sandia National Laboratories on October 28- 29, 2015. The document summarizes the structural and aeroelastic requirements placed on the NRT rotor for satisfactory deployment at the DOE/SNL SWiFT experimental facility to produce high-quality datasets for wind turbine model validation. The method and result of the NRT blade structural optimization is also presented within this report, along with analysis of its satisfaction of the design requirements.

  15. Preliminary Design of a LSA Aircraft Using Wind Tunnel Tests

    Directory of Open Access Journals (Sweden)

    Norbert ANGI

    2015-12-01

    Full Text Available This paper presents preliminary results concerning the design and aerodynamic calculations of a light sport aircraft (LSA. These were performed for a new lightweight, low cost, low fuel consumption and long-range aircraft. The design process was based on specific software tools as Advanced Aircraft Analysis (AAA, XFlr 5 aerodynamic and dynamic stability analysis, and Catia design, according to CS-LSA requirements. The calculations were accomplished by a series of tests performed in the wind tunnel in order to assess experimentally the aerodynamic characteristics of the airplane.

  16. Experience-Centered Design Designers, Users, and Communities in Dialogue

    CERN Document Server

    Wright, Peter

    2010-01-01

    Experience-centered design, experience-based design, experience design, designing for experience, user experience design. All of these terms have emerged and gained acceptance in the Human-Computer Interaction (HCI) and Interaction Design relatively recently. In this book, we set out our understanding of experience-centered design as a humanistic approach to designing digital technologies and media that enhance lived experience. The book is divided into three sections. In Section 1, we outline the historical origins and basic concepts that led into and flow out from our understanding of experi

  17. The Mixed Waste Management Facility. Preliminary design review

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    This document presents information about the Mixed Waste Management Facility. Topics discussed include: cost and schedule baseline for the completion of the project; evaluation of alternative options; transportation of radioactive wastes to the facility; capital risk associated with incineration; radioactive waste processing; scaling of the pilot-scale system; waste streams to be processed; molten salt oxidation; feed preparation; initial operation to demonstrate selected technologies; floorplans; baseline revisions; preliminary design baseline; cost reduction; and project mission and milestones.

  18. Preliminary design of large reflectors with flat facets

    Science.gov (United States)

    Agrawal, P. K.; Anderson, M. S.; Card, M. F.

    1981-01-01

    A concept for approximating curved antenna surfaces using flat facets is discussed. A preliminary design technique for determining the size of the reflector surface facets necessary to meet antenna surface accuracy requirements is presented. A proposed large microwave radiometer satellite (MRS) is selected as an application, and the far-field electromagnetic response of a faceted reflector surface is compared with that from a spherical reflector surface.

  19. OSU TOMF Program Site Selection and Preliminary Concept Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Spadling, Steve [Oklahoma State Univ., Stillwater, OK (United States)

    2012-05-10

    The purpose of this report is to confirm the programmatic requirements for the new facilities, identify the most appropriate project site, and develop preliminary site and building concepts that successfully address the overall project goals and site issues. These new facilities will be designed to accommodate the staff, drivers and maintenance requirements for the future mixed fleet of passenger vehicles, Transit Style Buses and School Buses.

  20. The Mixed Waste Management Facility. Preliminary design review

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    This document presents information about the Mixed Waste Management Facility. Topics discussed include: cost and schedule baseline for the completion of the project; evaluation of alternative options; transportation of radioactive wastes to the facility; capital risk associated with incineration; radioactive waste processing; scaling of the pilot-scale system; waste streams to be processed; molten salt oxidation; feed preparation; initial operation to demonstrate selected technologies; floorplans; baseline revisions; preliminary design baseline; cost reduction; and project mission and milestones.

  1. Biomechanics of injury prediction for anthropomorphic manikins - preliminary design considerations

    Energy Technology Data Exchange (ETDEWEB)

    Engin, A.E. [Univ. of South Alabama, Mobile, AL (United States)

    1996-12-31

    The anthropomorphic manikins are used in automobile safety research as well as in aerospace related applications. There is now a strong need to advance the biomechanics knowledge to determine appropriate criteria for injury likelihood prediction as functions of manikin-measured responses. In this paper, three regions of a manikin, namely, the head, knee joint, and lumbar spine are taken as examples to introduce preliminary design considerations for injury prediction by means of responses of theoretical models and strategically placed sensing devices.

  2. Preliminary design of the PANSAT electrical power subsystem

    OpenAIRE

    Noble, Michael Lynn

    1990-01-01

    Approved for public release; distribution unlimited. This thesis presents a preliminary design of the electrical power system (EPS) for the Naval Postgraduate School's Petite Amateur Navy Satellite (PANSAT). The EPS is a photovoltaic silicon cell system consisting of solar array, batteries, battery charge regulator (BCR), and dc-dc convertors. The EPS provides power for up to two years of low earth orbit (480 km) operations. The solar array consists of 17 panels with thirty-two 2x4 cm sola...

  3. Design of Multiphase Flow Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Urkedal, Hege

    1998-12-31

    This thesis proposes an experimental design procedure for multiphase experiments. The two-phase functions can be determined using data from a single experiment, while the three-phase relative permeabilities must be determined using data from multiple experiments. Various three-phase experimental designs have been investigated and the accuracy with which the flow functions may be determined using the corresponding data have been computed. Analytical sensitivity coefficients were developed from two-phase to three-phase flow. Sensitivity coefficients are the derivative of the model output with respect to the model parameters. They are obtained by a direct method that takes advantage of the fact that the model equations are solved using the Newton-Raphson method, and some of the results from this solution can be used directly when solving the sensitivity equation. Numerical derivatives are avoided, which improves accuracy. The thesis uses an inverse methodology for determination of two- and three-phase relative permeability and capillary pressure functions. The main work has been the development of analytical sensitivity coefficients for two-and three-phase flow. This technical contribution has improved the accuracy both in parameter estimation and accuracy assessment of the estimates and reduced the computer time requirements. The proposed experimental design is also dependent on accurate sensitivity coefficients to give the right guidelines for how two- and three-phase experiments should be conducted. Following the proposed experimental design, three-phase relative permeability and capillary pressure functions have been estimated when multiple sets of experimental data have been reconciled by simulations. 74 refs., 69 figs., 18 tabs.

  4. Engineering Design Handbook. Helicopter Engineering. Part One. Preliminary Design

    Science.gov (United States)

    1974-08-30

    by estimation, compound helicopter performance, to think of the air- plots of effective lift and drag areas and pitching mo- craft as a biplane having...stncural design problems but may produce loads that where are critikal locally. A = presented arms ft’ Ca = drag coefficient, dimensionless F• V = wind speed...groups is to be provided in accordance with MIL-STD- 1374, Part I. The useful load condition shall be as I. W. H. Ballhaus, Clear Design Thinking Using

  5. Preliminary design package for solar heating and hot water system

    Energy Technology Data Exchange (ETDEWEB)

    Levine, P.; Meyer, R.; White, James S.

    1977-01-01

    A collection of documents submitted by the Fern Engineering Company for the preliminary design review on the development of two prototype solar heating and hot water systems is presented. The information includes system certification, system functional description, system configuration, system specification, system performance and other documents pertaining to the progress and the design of the system. This system, which is intended for use in the normal single-family residence, consists of the following subsystems: collector, storage, control, transport, and Government-furnished Site Data Acquisition. One of the two prototype units will be installed in Lansing, Michigan, and the other in Tunkhannock, Pennsylvania.

  6. Bates solar industrial process-steam application: preliminary design review

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-07

    The design is analyzed for a parabolic trough solar process heat system for a cardboard corrugation fabrication facility in Texas. The program is briefly reviewed, including an analysis of the plant and process. The performance modeling for the system is discussed, and the solar system structural design, collector subsystem, heat transport and distribution subsystem are analyzed. The selection of the heat transfer fluid, and ullage and fluid maintenance are discussed, and the master control system and data acquisition system are described. Testing of environmental degradation of materials is briefly discussed. A brief preliminary cost analysis is included. (LEW)

  7. Design and preliminary testing of the RIC hybrid knee prosthesis.

    Science.gov (United States)

    Lenzi, T; Sensinger, J; Lipsey, J; Hargrove, L; Kuiken, T

    2015-08-01

    We present a novel hybrid knee prosthesis that uses a motor, transmission and control system only for active dynamics tasks, while relying on a spring/damper system for passive dynamics activities. Active dynamics tasks require higher torque, lower speed, and occur less frequently than passive dynamic activities. By designing the actuation system around active tasks alone, we achieved a lightweight design (1.7 Kg w/o battery) without sacrificing peak torque (85Nm repetitive). Preliminary tests performed by an able-bodied person using a bypass orthosis show that the hybrid knee can support reciprocal stairs ambulation with low electrical energy consumption.

  8. Fiscal year 1981 US corn and soybeans pilot preliminary experiment plan, phase 1

    Science.gov (United States)

    Livingston, G. P.; Nedelman, K. S.; Norwood, D. F.; Smith, J. H. (Principal Investigator)

    1981-01-01

    A draft of the preliminary experiment plan for the foreign commodity production forecasting project fiscal year 1981 is presented. This draft plan includes: definition of the phase 1 and 2 U.S. pilot objectives; the proposed experiment design to evaluate crop calendar, area estimation, and area aggregation components for corn and soybean technologies using 1978/1979 crop-year data; a description of individual sensitivity evaluations of the baseline corn and soybean segment classification procedure; and technology and data assessment in support of the corn and soybean estimation technology for use in the U.S. central corn belt.

  9. The MathScheme Library: Some Preliminary Experiments

    CERN Document Server

    Carette, Jacques; Jeremic, Filip; Maccio, Vincent; O'Connor, Russell; Tran, Quang M

    2011-01-01

    We present some of the experiments we have performed to best test our design for a library for MathScheme, the mechanized mathematics software system we are building. We wish for our library design to use and reflect, as much as possible, the mathematical structure present in the objects which populate the library.

  10. Designing Effective Undergraduate Research Experiences

    Science.gov (United States)

    Severson, S.

    2010-12-01

    I present a model for designing student research internships that is informed by the best practices of the Center for Adaptive Optics (CfAO) Professional Development Program. The dual strands of the CfAO education program include: the preparation of early-career scientists and engineers in effective teaching; and changing the learning experiences of students (e.g., undergraduate interns) through inquiry-based "teaching laboratories." This paper will focus on the carry-over of these ideas into the design of laboratory research internships such as the CfAO Mainland internship program as well as NSF REU (Research Experiences for Undergraduates) and senior-thesis or "capstone" research programs. Key ideas in maximizing student learning outcomes and generating productive research during internships include: defining explicit content, scientific process, and attitudinal goals for the project; assessment of student prior knowledge and experience, then following up with formative assessment throughout the project; setting reasonable goals with timetables and addressing motivation; and giving students ownership of the research by implementing aspects of the inquiry process within the internship.

  11. The Geoengineering Model Intercomparison Project Phase 6 (GeoMIP6: simulation design and preliminary results

    Directory of Open Access Journals (Sweden)

    B. Kravitz

    2015-06-01

    simulations, and has been expanded to address several further important topics, including key uncertainties in extreme events, the use of geoengineering as part of a portfolio of responses to climate change, and the relatively new idea of cirrus cloud thinning to allow more longwave radiation to escape to space. We discuss experiment designs, as well as the rationale for those designs, showing preliminary results from individual models when available. We also introduce a new feature, called the GeoMIP Testbed, which provides a platform for simulations that will be performed with a few models and subsequently assessed to determine whether the proposed experiment designs will be adopted as core (Tier 1 GeoMIP experiments. This is meant to encourage various stakeholders to propose new targeted experiments that address their key open science questions, with the goal of making GeoMIP more relevant to a broader set of communities.

  12. 4MOST systems engineering: from conceptual design to preliminary design review

    Science.gov (United States)

    Bellido-Tirado, Olga; Frey, Steffen; Barden, Samuel C.; Brynnel, Joar; Giannone, Domenico; Haynes, Roger; de Jong, Roelof S.; Phillips, Daniel; Schnurr, Olivier; Walcher, Jakob; Winkler, Roland

    2016-08-01

    The 4MOST Facility is a high-multiplex, wide-field, brief-fed spectrograph system for the ESO VISTA telescope. It aims to create a world-class spectroscopic survey facility unique in its combination of wide-field multiplex, spectral resolution, spectral coverage, and sensitivity. At the end of 2014, after a successful concept optimization design phase, 4MOST entered into its Preliminary Design Phase. Here we present the process and tools adopted during the Preliminary Design Phase to define the subsystems specifications, coordinate the interface control documents and draft the system verification procedures.

  13. Voltage-Controlled Sapphire Oscillator: Design, Development, and Preliminary Performance

    Science.gov (United States)

    Wang, R. T.; Dick, G. J.; Tjoelker, R. L.

    2007-08-01

    We present the design for a new short-term frequency standard, the voltage-controlled sapphire oscillator, as a practical and lower-cost alternative to a cryogenic sapphire oscillator operating at liquid helium temperatures. Performance goals are a frequency stability of 1 x 10^-14 (1 second equal to or less than tau equal to or less than 100 seconds), more than 2 years of continuous operation, and practical operability. Key elements include the sapphire resonator, low-power and long-life cryocooler, frequency compensation method, and cryo-Pound design. We report the design verification, experimental results, and test results of the cryocooler environmental sensitivity, as well as a preliminary stability measurement.

  14. Preliminary Design of Reluctance Motors for Light Electric Vehicles Driving

    Directory of Open Access Journals (Sweden)

    TRIFA, V.

    2009-02-01

    Full Text Available The paper presents the aspects regarding FEM analysis of a reluctant motor for direct driving of the light electric vehicles. The reluctant motor take into study is of special construction suitable for direct drive of a light electric vehicle. It is an inverse radial reluctant motor, with a fixed stator mounted on front wheel shaft and an external toothed rotor fixed on the front wheel itself. A short presentation of preliminary design is continued with the FEM analysis in order to provide the optimal geometry of the motor and adequate windings.

  15. Preliminary design and R&D of ITER diagnostic-radial X-ray camera

    Science.gov (United States)

    Hu, L.; Chen, K.; Chen, Y.; Cao, H.; Li, S.; Yu, H.; Zhan, J.; Shen, J.; Qin, S.; Sheng, X.; Zhao, J.; Niu, L.; Feng, C.; Ge, J.; Zhang, S.; Zhang, B.

    2017-10-01

    Preliminary design of ITER Radial X-ray Camera (RXC) has been finished. The structure design is optimized and installation process is studied considering the simplification and easiness of maintenance. Remote handling procedures are designed for the system maintenance after being activated. For detector cooling against high environment temperature which can be up to 240°, a dedicated gas cooling system using heat exchanger is designed. The structure analysis indicates that the stresses and displacements of most of the components under load combinations are within the allowable limits and no Safety Important Component (SIC) boundary is damaged. Through putting B4C material in the front part of DSM and around detectors for neutron shielding, the detectors are expected to survive the whole D-D phase. As for electronics, preliminary design of highly integrated pre-amplifier and program controllable mid-amplifier has been completed, both with bandwidth greater than 100 kHz to meet time resolution requirement of 20 kHz. To protect the electronics from intensive neutron and gamma irradiation, shielding cabinet capable of attenuating neutron flux down to 0.0001 and gamma dose 0.01 is designed. Besides, many R&D has been done to support the design. The tests of pre-amplifier and mid-amplifier indicated the electronics had no functional problem when debugging together and generally passed preliminary ElectroMagnetic Compatibility (EMC) test and nuclear test. The highly-integrated compact pre-amplifier has been used in EAST and proved useful. To test the feasibility of dedicated gas cooling system for detectors, a cooling test platform was built and preliminary cooling test has been done, indicating that during 250°baking the detector temperature is promising to be cooled down to the detector temperature limit of 75°. To increase signal to noise ratio, large area detector with dark current less than 2nA has been manufactured and worked steadily in EAST experiments.

  16. Calibration Study and Preliminary Results of PRad Experiment

    Science.gov (United States)

    Levillain, Maxime; PRad Collaboration

    2016-09-01

    The latest measurements of the proton radius through muonic hydrogen Lamb shift show a discrepancy of 7 σ from a global analysis of standard hydrogen Lamb shift and elastic ep -scattering. In order to understand this proton radius puzzle, the PRad experiment successfully took in last June some elastic ep -scattering data at very low Q2 (2 .10-4 to 10-1 GeV2) with very accurate angle and energy measurements to minimize the systematic uncertainties. Before measuring the cross-sections that will be used to extract the electromagnetic form factor GE(Q2) and the proton radius, a very careful calibration of the electromagnetic calorimeter (HyCal) must be performed to get a good energy resolution and separate ep -events from M øller events especially at low angle. We will present an extended study of the electromagnetic calorimeter calibration of this experiment as well as some preliminary results on ep - and ee -scattering processes extracted from the data. The PRad experiment is supported in part by NSF MRI Award PHY-1229153.

  17. Social Design Experiments: Toward Equity by Design

    Science.gov (United States)

    Gutiérrez, Kris D.; Jurow, A. Susan

    2016-01-01

    In this article, we advance an approach to design research that is organized around a commitment to transforming the educational and social circumstances of members of non-dominant communities as a means of promoting social equity and learning. We refer to this approach as social design experimentation. The goals of social design experiments…

  18. Radiometer experiment for the aeroassist flight experiment. [Thermal protection data for Orbital Transfer Vehicle design

    Science.gov (United States)

    Davy, W. C.; Park, C.; Arnold, J. O.; Balakrishnan, A.

    1985-01-01

    A forthcoming NASA flight experiment is described that provides an opportunity to obtain a large base of radiometric data for high-altitude, high-velocity thermochemically nonequilibrated-flow conditions. As a preliminary to the design of a radiometer for this experiment, an approximate method for predicting both equilibrium and nonequilibrium radiative surface fluxes is described. Spectral results for one trajectory state, a velocity of 10 km/sec at an altitude of 85 km, are presented. These results are then used to develop some of the instrument parameters that will be needed for designing of the three genre of radiometers that are proposed for this experiment.

  19. Design and preliminary test results of Daya Bay RPC modules*

    Energy Technology Data Exchange (ETDEWEB)

    Hackenburg, R.

    2011-09-01

    Resistive Plate Chamber (RPC) modules will be used as one part of the cosmic muon veto system in the Daya Bay reactor neutrino experiment. A total of 189 RPC modules will cover the three water pools in the experiment. To achieve track reconstruction and high efficiency, each module consists of 4 layers, each of which contains two sizes of bare chambers. The placement of bare chambers is reversed in different layers to reduce the overlapping dead areas. The module efficiency and patch efficiency were studied both in simulation and test of the data analysis. 143 modules have been constructed and tested. The preliminary study shows that the module and patch 3 out of 4 layers efficiency reaches about 98%.

  20. Design and preliminary test results of Daya Bay RPC modules

    Institute of Scientific and Technical Information of China (English)

    XU Ji-Lei; Logan Lebanowski; Cullen Newsom; Lin Shih-Kai; Jonathan Link; MA Lie-Hua; Viktor Pě(c); Vit Vorobel; CHEN Jin; LIU Jin-Chang; ZHOU Yong-Zhao; GUAN Meng-Yun; LIANG Hao; YANG Chang-Gen; WANG Yi-Fang; ZHANG Jia-Wen; LU Chang-Guo; Kirk McDonald; Robert Hackenburg; Kwong Lau

    2011-01-01

    Resistive Plate Chamber(RPC)modules will be used as one part of the cosmic muon veto system in the Days Bay reactor neutrino experiment.A total of 189 RPC modules will cover the three water pools in the experiment.To achieve track reconstruction and high efficiency,each module consists of 4 layers,each of which contains two sizes of bare chambers.The placement of bare chambers is reversed in different layers to reduce the overlapping dead areas.The module efficiency and patch efficiency were studied both in simulation and test of the data analysis.143 modules have been constructed and tested.The preliminary study shows that the module and patch 3 out of 4 layers efficiency reaches about 98%.

  1. A preliminary design for a satellite power system

    Science.gov (United States)

    Enriquez, Clara V.; Kokaly, Ray; Nandi, Saumya; Timmons, Mike; Garrard, Mark; Mercado, Rommel; Rogers, Brian; Ugaz, Victor

    1991-01-01

    Outlined here is a preliminary design for a Solar Power Satellite (SPS) system. The SPS will provide a clean, reliable source of energy for mass consumption. The system will use satellites in geostationary orbits around the Earth to capture the sun's energy. The intercepted sunlight will be converted to laser beam energy which can be transmitted to the Earth's surface. Ground systems on the Earth will convert the transmissions from space into electric power. The preliminary design for the SPS consists of one satellite in orbit around the Earth transmitting to one ground station. The SPs technology uses multi-layer solar cell technology arranged on a 20 sq km planar array to intercept sunlight and convert it to an electric voltage. Power conditioning devices then send the electricity to a laser, which transmits the power to the surface of the Earth. A ground station will convert the beam into electricity. Construction will take place in low Earth orbit and array sections, 20 in total, will be sailed on the solar wind out to the GEO location in 150 days. These individual transportation sections are referred to as solar sailing panels (SSAPs). The primary truss elements used to support the arrays are composed on composite tubular members in a pentahedral arrangement. Smart segments consisting of passive and active damping devices will increase the control of dynamic SPS modes.

  2. The NASA Juncture Flow Experiment: Goals, Progress, and Preliminary Testing (Invited)

    Science.gov (United States)

    Rumsey, Christopher L.; Neuhart, Danny H.; Kegerise, Michael A.

    2016-01-01

    NASA has been working toward designing and conducting a juncture flow experiment on a wing-body aircraft configuration. The experiment is planned to provide validation-quality data for CFD that focuses on the onset and progression of a separation bubble near the wing-body juncture trailing edge region. This paper describes the goals and purpose of the experiment. Although currently considered unreliable, preliminary CFD analyses of several different configurations are shown. These configurations have been subsequently tested in a series of "risk-reduction" wind tunnel tests, in order to help down-select to a final configuration that will attain the desired flow behavior. The risk-reduction testing at the higher Reynolds number has not yet been completed (at the time of this writing), but some results from one of the low-Reynolds-number experiments are shown.

  3. Preliminary design of the advanced quantum beam source

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Byung Cheol; Lee, Jong Min; Jeong, Young Uk; Cho, Sung Oh; Yoo, Jae Gwon; Park, Seong Hee

    2000-07-01

    The preliminary design of the advanced quantum beam source based on a superconducting electron accelerator is presented. The advanced quantum beams include: high power free electron lasers, monochromatic X-rays and {gamma}-rays, high-power medium-energy electrons, high-flux pulsed neutrons, and high-flux monochromatic slow positron beam. The AQBS system is being re-designed, assuming that the SPS superconducting RF cavities used for LEP at CERN will revived as a main accelerator of the AQBS system at KAERI, after the decommissioning of LEP at the end of 2000. Technical issues of using the SPS superconducting RF cavities for the AQBS project are discussed in this report. The advanced quantum beams will be used for advanced researches in science and industries.

  4. Preliminary Design Through Graphs: A Tool for Automatic Layout Distribution

    Directory of Open Access Journals (Sweden)

    Carlo Biagini

    2015-02-01

    Full Text Available Diagrams are essential in the preliminary stages of design for understanding distributive aspects and assisting the decision-making process. By drawing a schematic graph, designers can visualize in a synthetic way the relationships between many aspects: functions and spaces, distribution of layouts, space adjacency, influence of traffic flows within a facility layout, and so on. This process can be automated through the use of modern Information and Communication Technologies tools (ICT that allow the designers to manage a large quantity of information. The work that we will present is part of an on-going research project into how modern parametric software influences decision-making on the basis of automatic and optimized layout distribution. The method involves two phases: the first aims to define the ontological relation between spaces, with particular reference to a specific building typology (rules of aggregation of spaces; the second entails the implementation of these rules through the use of specialist software. The generation of ontological relations begins with the collection of data from historical manuals and analyses of case studies. These analyses aim to generate a “relationship matrix” based on preferences of space adjacency. The phase of implementing the previously defined rules is based on the use of Grasshopper to analyse and visualize different layout configurations. The layout is generated by simulating a process involving the collision of spheres, which represents specific functions of the design program. The spheres are attracted or rejected as a function of the relationships matrix, as defined above. The layout thus obtained will remain in a sort of abstract state independent of information about the exterior form, but will still provide a useful tool for the decision-making process. In addition, preliminary results gathered through the analysis of case studies will be presented. These results provide a good variety

  5. Spinel dissolution via addition of glass forming chemicals. Results of preliminary experiments

    Energy Technology Data Exchange (ETDEWEB)

    Fox, K. M. [Savannah River Site (SRS), Aiken, SC (United States); Johnson, F. C. [Savannah River Site (SRS), Aiken, SC (United States)

    2015-11-01

    Increased loading of high level waste in glass can lead to crystallization within the glass. Some crystalline species, such as spinel, have no practical impact on the chemical durability of the glass, and therefore may be acceptable from both a processing and a product performance standpoint. In order to operate a melter with a controlled amount of crystallization, options must be developed for remediating an unacceptable accumulation of crystals. This report describes preliminary experiments designed to evaluate the ability to dissolve spinel crystals in simulated waste glass melts via the addition of glass forming chemicals (GFCs).

  6. Blade system design studies volume II : preliminary blade designs and recommended test matrix.

    Energy Technology Data Exchange (ETDEWEB)

    Griffin, Dayton A. (Global Energy Concepts, LLC, Kirkland, WA)

    2004-06-01

    As part of the U.S. Department of Energy's Wind Partnerships for Advanced Component Technologies (WindPACT) program, Global Energy Concepts, LLC is performing a Blade System Design Study (BSDS) concerning innovations in materials, processes and structural configurations for application to wind turbine blades in the multi-megawatt range. The BSDS Volume I project report addresses issues and constraints identified to scaling conventional blade designs to the megawatt size range, and evaluated candidate materials, manufacturing and design innovations for overcoming and improving large blade economics. The current report (Volume II), presents additional discussion of materials and manufacturing issues for large blades, including a summary of current trends in commercial blade manufacturing. Specifications are then developed to guide the preliminary design of MW-scale blades. Using preliminary design calculations for a 3.0 MW blade, parametric analyses are performed to quantify the potential benefits in stiffness and decreased gravity loading by replacement of a baseline fiberglass spar with carbon-fiberglass hybrid material. Complete preliminary designs are then presented for 3.0 MW and 5.0 MW blades that incorporate fiberglass-to-carbon transitions at mid-span. Based on analysis of these designs, technical issues are identified and discussed. Finally, recommendations are made for composites testing under Part I1 of the BSDS, and the initial planned test matrix for that program is presented.

  7. Preliminary Design Study of the Hollow Electron Lens for LHC

    CERN Document Server

    Perini, Diego; CERN. Geneva. ATS Department

    2017-01-01

    A Hollow Electron Lens (HEL) has been proposed in order to improve performance of halo control and collimation in the Large Hadron Collider in view of its High Luminosity upgrade (HL-LHC). The concept is based on a beam of electrons that travels around the protons for a few meters. The electron beam is produced by a cathode and then guided by a strong magnetic field generated by a set of superconducting solenoids. The first step of the design is the definition of the magnetic fields that drive the electron trajectories. The estimation of such trajectories by means of a dedicated MATLAB® tool is presented. The influence of the main geometrical and electrical parameters are analysed and discussed. Then, the main mechanical design choices for the solenoids, cryostats gun and collector are described. The aim of this paper is to provide an overview of the preliminary design of the Electron Lens for LHC. The methods used in this study also serve as examples for future mechanical and integration designs of similar ...

  8. Introducing Experience Goals into Packaging Design

    OpenAIRE

    Joutsela, Markus; Roto, Virpi; Lloyd, Peter; Bohemia, Erik

    2016-01-01

    Consumer experiences are an increasingly important driving force for commerce, affecting also packaging design. Yet, experience design for packages is rarely studied. Specifically, there is a gap in research regarding the integration of experiential goals, Xgoals, into the packaging design process. Open questions include how to describe Xgoals in design briefs when package design is outsourced, how to deal with changes during the design process, and how to evaluate whether the delivered desig...

  9. Development and implementation of rotorcraft preliminary design methodology using multidisciplinary design optimization

    Science.gov (United States)

    Khalid, Adeel Syed

    Rotorcraft's evolution has lagged behind that of fixed-wing aircraft. One of the reasons for this gap is the absence of a formal methodology to accomplish a complete conceptual and preliminary design. Traditional rotorcraft methodologies are not only time consuming and expensive but also yield sub-optimal designs. Rotorcraft design is an excellent example of a multidisciplinary complex environment where several interdependent disciplines are involved. A formal framework is developed and implemented in this research for preliminary rotorcraft design using IPPD methodology. The design methodology consists of the product and process development cycles. In the product development loop, all the technical aspects of design are considered including the vehicle engineering, dynamic analysis, stability and control, aerodynamic performance, propulsion, transmission design, weight and balance, noise analysis and economic analysis. The design loop starts with a detailed analysis of requirements. A baseline is selected and upgrade targets are identified depending on the mission requirements. An Overall Evaluation Criterion (OEC) is developed that is used to measure the goodness of the design or to compare the design with competitors. The requirements analysis and baseline upgrade targets lead to the initial sizing and performance estimation of the new design. The digital information is then passed to disciplinary experts. This is where the detailed disciplinary analyses are performed. Information is transferred from one discipline to another as the design loop is iterated. To coordinate all the disciplines in the product development cycle, Multidisciplinary Design Optimization (MDO) techniques e.g. All At Once (AAO) and Collaborative Optimization (CO) are suggested. The methodology is implemented on a Light Turbine Training Helicopter (LTTH) design. Detailed disciplinary analyses are integrated through a common platform for efficient and centralized transfer of design

  10. Adaptive designs for sequential experiments

    Institute of Scientific and Technical Information of China (English)

    林正炎; 张立新

    2003-01-01

    Various adaptive designs have been proposed and applied to clinical trials, bioassay, psychophysics, etc.Adaptive designs are also useful in high cost engineering trials.More and more people have been paying attention to these design methods. This paper introduces several broad families of designs, such as the play-the-winner rule, randomized play-the-winner rule and its generalization to the multi-arm case, doubly biased coin adaptive design, Markov chain model.

  11. Preliminary design of the INPE's Solar Vector Magnetograph

    CERN Document Server

    Vieira, L E A; Lago, A Dal; Wrasse, C; Echer, E; Guarnieri, F L; Cardoso, F Reis; Guerrero, G; Costa, J Rezende; Palacios, J; Balmaceda, L; Alves, L Ribeiro; da Silva, L; Costa, L L; Sampaio, M; Soares, M C Rabello; Barbosa, M; Domingues, M; Rigozo, N; Mendes, O; Jauer, P; Dallaqua, R; Branco, R H; Stekel, T; Gonzalez, W; Kabata, W

    2016-01-01

    We describe the preliminary design of a magnetograph and visible-light imager instrument to study the solar dynamo processes through observations of the solar surface magnetic field distribution. The instrument will provide measurements of the vector magnetic field and of the line-of-sight velocity in the solar photosphere. As the magnetic field anchored at the solar surface produces most of the structures and energetic events in the upper solar atmosphere and significantly influences the heliosphere, the development of this instrument plays an important role in reaching the scientific goals of The Atmospheric and Space Science Coordination (CEA) at the Brazilian National Institute for Space Research (INPE). In particular, the CEA's space weather program will benefit most from the development of this technology. We expect that this project will be the starting point to establish a strong research program on Solar Physics in Brazil. Our main aim is acquiring progressively the know-how to build state-of-art sol...

  12. A preliminary design of the collinear dielectric wakefield accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Zholents, A.; Gai, W.; Doran, S.; Lindberg, R.; Power, J.G.; Strelnikov, N.; Sun, Y.; Trakhtenberg, E.; Vasserman, I. [ANL, Argonne, IL 60439 (United States); Jing, C.; Kanareykin, A.; Li, Y. [Euclid Techlabs LLC, Solon, OH 44139 (United States); Gao, Q. [Tsinghua University, Beijing (China); Shchegolkov, D.Y.; Simakov, E.I. [LANL, Los Alamos, NM 87545 (United States)

    2016-09-01

    A preliminary design of the multi-meter long collinear dielectric wakefield accelerator that achieves a highly efficient transfer of the drive bunch energy to the wakefields and to the witness bunch is considered. It is made from ~0.5 m long accelerator modules containing a vacuum chamber with dielectric-lined walls, a quadrupole wiggler, an rf coupler, and BPM assembly. The single bunch breakup instability is a major limiting factor for accelerator efficiency, and the BNS damping is applied to obtain the stable multi-meter long propagation of a drive bunch. Numerical simulations using a 6D particle tracking computer code are performed and tolerances to various errors are defined.

  13. The Pierre Auger Observatory Upgrade - Preliminary Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Aab, Alexander [Univ. Siegen (Germany); et al.

    2016-04-12

    The Pierre Auger Observatory has begun a major Upgrade of its already impressive capabilities, with an emphasis on improved mass composition determination using the surface detectors of the Observatory. Known as AugerPrime, the upgrade will include new 4 m2 plastic scintillator detectors on top of all 1660 water-Cherenkov detectors, updated and more flexible surface detector electronics, a large array of buried muon detectors, and an extended duty cycle for operations of the fluorescence detectors. This Preliminary Design Report was produced by the Collaboration in April 2015 as an internal document and information for funding agencies. It outlines the scientific and technical case for AugerPrime. We now release it to the public via the arXiv server. We invite you to review the large number of fundamental results already achieved by the Observatory and our plans for the future.

  14. The Pierre Auger Observatory Upgrade - Preliminary Design Report

    CERN Document Server

    Aab, A; Aglietta, M; Ahn, E J; Samarai, I Al; Albuquerque, I F M; Allekotte, I; Allison, P; Almela, A; Castillo, J Alvarez; Alvarez-Muñiz, J; Batista, R Alves; Ambrosio, M; Aminaei, A; Anchordoqui, L; Andringa, S; Aramo, C; Arqueros, F; Arsene, N; Asorey, H; Assis, P; Aublin, J; Ave, M; Avenier, M; Avila, G; Awal, N; Badescu, A M; Barber, K B; Bäuml, J; Baus, C; Beatty, J J; Becker, K H; Bellido, J A; Berat, C; Bertaina, M E; Bertou, X; Biermann, P L; Billoir, P; Blaess, S G; Blanco, A; Blanco, M; Blazek, J; Bleve, C; Blümer, H; Boháčová, M; Boncioli, D; Bonifazi, C; Borodai, N; Brack, J; Brancus, I; Bridgeman, A; Brogueira, P; Brown, W C; Buchholz, P; Bueno, A; Buitink, S; Buscemi, M; Caballero-Mora, K S; Caccianiga, B; Caccianiga, L; Candusso, M; Caramete, L; Caruso, R; Castellina, A; Cataldi, G; Cazon, L; Cester, R; Chavez, A G; Chiavassa, A; Chinellato, J A; Chudoba, J; Cilmo, M; Clay, R W; Cocciolo, G; Colalillo, R; Coleman, A; Collica, L; Coluccia, M R; Conceição, R; Contreras, F; Cooper, M J; Cordier, A; Coutu, S; Covault, C E; Cronin, J; Dallier, R; Daniel, B; Dasso, S; Daumiller, K; Dawson, B R; de Almeida, R M; de Jong, S J; De Mauro, G; Neto, J R T de Mello; De Mitri, I; de Oliveira, J; de Souza, V; del Peral, L; Deligny, O; Dembinski, H; Dhital, N; Di Giulio, C; Di Matteo, A; Diaz, J C; Castro, M L Díaz; Diogo, F; Dobrigkeit, C; Docters, W; D'Olivo, J C; Dorofeev, A; Hasankiadeh, Q Dorosti; Dova, M T; Ebr, J; Engel, R; Erdmann, M; Erfani, M; Escobar, C O; Espadanal, J; Etchegoyen, A; Falcke, H; Fang, K; Farrar, G; Fauth, A C; Fazzini, N; Ferguson, A P; Fernandes, M; Fick, B; Figueira, J M; Filevich, A; Filipčič, A; Fox, B D; Fratu, O; Freire, M M; Fuchs, B; Fujii, T; García, B; Garcia-Pinto, D; Gate, F; Gemmeke, H; Gherghel-Lascu, A; Ghia, P L; Giaccari, U; Giammarchi, M; Giller, M; Głas, D; Glaser, C; Glass, H; Golup, G; Berisso, M Gómez; Vitale, P F Gómez; González, N; Gookin, B; Gordon, J; Gorgi, A; Gorham, P; Gouffon, P; Griffith, N; Grillo, A F; Grubb, T D; Guarino, F; Guedes, G P; Hampel, M R; Hansen, P; Harari, D; Harrison, T A; Hartmann, S; Harton, J L; Haungs, A; Hebbeker, T; Heck, D; Heimann, P; Hemery, N; Herve, A E; Hill, G C; Hojvat, C; Hollon, N; Holt, E; Homola, P; Hörandel, J R; Horvath, P; Hrabovský, M; Huber, D; Huege, T; Insolia, A; Isar, P G; Jandt, I; Jansen, S; Jarne, C; Johnsen, J A; Josebachuili, M; Kääpä, A; Kambeitz, O; Kampert, K H; Kasper, P; Katkov, I; Kégl, B; Keilhauer, B; Keivani, A; Kemp, E; Kieckhafer, R M; Klages, H O; Kleifges, M; Kleinfeller, J; Krause, R; Krohm, N; Krömer, O; Kuempel, D; Mezek, G Kukec; Kunka, N; LaHurd, D; Latronico, L; Lauer, R; Lauscher, M; Lautridou, P; Coz, S Le; Lebrun, D; Lebrun, P; de Oliveira, M A Leigui; Letessier-Selvon, A; Lhenry-Yvon, I; Link, K; Lopes, L; López, R; Casado, A López; Louedec, K; Lu, L; Lucero, A; Malacari, M; Maldera, S; Mallamaci, M; Maller, J; Mandat, D; Mantsch, P; Mariazzi, A G; Marin, V; Mariş, I C; Marsella, G; Martello, D; Martin, L; Martinez, H; Bravo, O Martínez; Martraire, D; Meza, J J Masías; Mathes, H J; Mathys, S; Matthews, J; Matthews, J A J; Matthiae, G; Maurizio, D; Mayotte, E; Mazur, P O; Medina, C; Medina-Tanco, G; Meissner, R; Mello, V B B; Melo, D; Menshikov, A; Messina, S; Meyhandan, R; Micheletti, M I; Middendorf, L; Minaya, I A; Miramonti, L; Mitrica, B; Molina-Bueno, L; Mollerach, S; Montanet, F; Morello, C; Mostafá, M; Moura, C A; Muller, M A; Müller, G; Müller, S; Mussa, R; Navarra, G; Navas, S; Necesal, P; Nellen, L; Nelles, A; Neuser, J; Nguyen, P H; Niculescu-Oglinzanu, M; Niechciol, M; Niemietz, L; Niggemann, T; Nitz, D; Nosek, D; Novotny, V; Nožka, L; Ochilo, L; Oikonomou, F; Olinto, A; Pacheco, N; Selmi-Dei, D Pakk; Palatka, M; Pallotta, J; Papenbreer, P; Parente, G; Parra, A; Paul, T; Pech, M; Pȩkala, J; Pelayo, R; Pepe, I M; Perrone, L; Petermann, E; Peters, C; Petrera, S; Petrov, Y; Phuntsok, J; Piegaia, R; Pierog, T; Pieroni, P; Pimenta, M; Pirronello, V; Platino, M; Plum, M; Porcelli, A; Porowski, C; Prado, R R; Privitera, P; Prouza, M; Purrello, V; Quel, E J; Querchfeld, S; Quinn, S; Rautenberg, J; Ravel, O; Ravignani, D; Reinert, D; Revenu, B; Ridky, J; Riggi, S; Risse, M; Ristori, P; Rizi, V; de Carvalho, W Rodrigues; Fernandez, G Rodriguez; Rojo, J Rodriguez; Rodríguez-Frías, M D; Rogozin, D; Rosado, J; Roth, M; Roulet, E; Rovero, A C; Saffi, S J; Saftoiu, A; Salamida, F; Salazar, H; Saleh, A; Greus, F Salesa; Salina, G; Sánchez, F; Sanchez-Lucas, P; Santos, E; Santos, E M; Sarazin, F; Sarkar, B; Sarmento, R; Sato, R; Scarso, C; Schauer, M; Scherini, V; Schieler, H; Schmidt, D; Scholten, O; Schoorlemmer, H; Schovánek, P; Schröder, F G; Schulz, A; Schulz, J; Schumacher, J; Sciutto, S J; Segreto, A; Settimo, M; Shadkam, A; Shellard, R C; Sidelnik, I; Sigl, G; Sima, O; Śmiałkowski, A; Šmída, R; Snow, G R; Sommers, P; Sorokin, J; Squartini, R; Srivastava, Y N; Stanca, D; Stanič, S; Stapleton, J; Stasielak, J; Stephan, M; Stutz, A; Suarez, F; Suomijärvi, T; Supanitsky, A D; Sutherland, M S; Swain, J; Szadkowski, Z; Taborda, O A; Tapia, A; Tepe, A; Theodoro, V M; Timmermans, C; Peixoto, C J Todero; Toma, G; Tomankova, L; Tomé, B; Tonachini, A; Elipe, G Torralba; Machado, D Torres; Travnicek, P; Trini, M; Ulrich, R; Unger, M; Urban, M; Galicia, J F Valdés; Valiño, I; Valore, L; van Aar, G; van Bodegom, P; Berg, A M van den; van Velzen, S; van Vliet, A; Varela, E; Cárdenas, B Vargas; Varner, G; Vasquez, R; Vázquez, J R; Vázquez, R A; Veberič, D; Verzi, V; Vicha, J; Videla, M; Villaseñor, L; Vlcek, B; Vorobiov, S; Wahlberg, H; Wainberg, O; Walz, D; Watson, A A; Weber, M; Weidenhaupt, K; Weindl, A; Werner, F; Widom, A; Wiencke, L; Wilczyński, H; Winchen, T; Wittkowski, D; Wundheiler, B; Wykes, S; Yang, L; Yapici, T; Yushkov, A; Zas, E; Zavrtanik, D; Zavrtanik, M; Zepeda, A; Zhu, Y; Zimmermann, B; Ziolkowski, M; Zong, Z; Zuccarello, F

    2016-01-01

    The Pierre Auger Observatory has begun a major Upgrade of its already impressive capabilities, with an emphasis on improved mass composition determination using the surface detectors of the Observatory. Known as AugerPrime, the upgrade will include new 4 m$^2$ plastic scintillator detectors on top of all 1660 water-Cherenkov detectors, updated and more flexible surface detector electronics, a large array of buried muon detectors, and an extended duty cycle for operations of the fluorescence detectors. This Preliminary Design Report was produced by the Collaboration in April 2015 as an internal document and information for funding agencies. It outlines the scientific and technical case for AugerPrime. We now release it to the public via the arXiv server. We invite you to review the large number of fundamental results already achieved by the Observatory and our plans for the future.

  15. Preliminary design for a pierce wiggler beamstick and addendum

    Energy Technology Data Exchange (ETDEWEB)

    Pirkle, D.

    1988-05-01

    Lawrence Livermore National Laboratory is developing a fast tunable microwave source for operation at 250 GHz and 10kW peak output power. This report presents the preliminary design of a Pierce gun and solenoid magnet that will be compatible with a Pierce-wiggler electron beam formation system (beamstick). The beamstick will be an appropriate power source for a tunable gyro-BWO at 250 GHz. Figure 1 presents the major components of the Pierce-wiggler beamstick: the electron gun, solenoid, beam tunnel, wiggler, and vacuum valve. Figure 2 shows an artistic conception of how the beamstick will interface with the interaction magnet, modulator and gyro-BWO circuit at MIT. 15 figs.

  16. Preliminary design of 600 MWt HTGR-gas turbine plant

    Energy Technology Data Exchange (ETDEWEB)

    Muto, Yasushi; Miyamoto, Yoshiaki; Shiozawa, Shusaku [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment

    1999-07-01

    In JAERI a feasibility study of the High Temperature Gas-cooled Reactor - Gas Turbine (HTGR-GT) system has been carried out since January, 1997 as an assigned work by the Science and Technology Agency. This paper describes a result of a preliminary design for a direct cycle plant of 600 MWt carried out in 1997 fiscal year within the framework of this feasibility study. A reactor inlet gas temperature of 460degC, a reactor outlet gas temperature of 850degC and a helium gas pressure of 6 MPa were selected. A power density of 6 MW/m{sup 3} and the maximum burnup of 10{sup 5} MWD/ton were achieved. A single-shaft horizontal turbomachine of 3600 rpm was selected and placed in a turbine vessel. A net thermal efficiency of 45.7% is expected to be achieved. (author)

  17. Preliminary Design of Large Scale Sodium Thermal-Hydraulic Test Facility

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Tae Ho; Kim, Tae Joon; Eoh, Jae Hyuk; Lee, Hyeong Yeon; Lee, Jae Han; Jeong, Ji Young; Park, Su Ki; Han, Ji Woong; Yoo, Yong Hwan; Lee, Yong Bum [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2009-10-15

    A large scale sodium thermal-hydraulic test facility is being designed for verification of the advanced design concept of the passive decay heat removal circuit (PDRC) in a medium- or large-sized pool-type SFR. In the test, its cooling capability during the long- and short-term periods after the reactor trip will be evaluated, and also the produced experimental data will be utilized for the assessment and verification of the safety and performance analysis codes. Starting with the preliminary design of the test facility this year using KALIMER-600 as a reference reactor, the basic and the detailed designs will be made through 2011-2012 based on the demonstration reactor which is intended to be constructed by 2028 according to a long-term national SFR development plan. The installation is scheduled to be completed by the end of 2013, and the main experiments will commence from 2015 after the startup test in 2014. This paper briefly introduces the preliminary design features which were produced as a first step to assess the appropriateness of the facility design methodology.

  18. Preliminary results of the XR2-1 experiment

    Energy Technology Data Exchange (ETDEWEB)

    Gauntt, R.O.; Helmick, P.H. [Sandia National Labs., Albuquerque, NM (United States); Humphries, L. [SAIC, Albuquerque, NM (United States)

    1996-03-01

    The XR2-1 (Ex-Reactor) experiment, investigating metallic core-melt relocation in boiling water reactor geometry, was performed on October 12, 1995, following two previous simpler XR1-series tests in August and November of 1993. The XR2-1 test made use of a highly detailed replication of the lower region of the BWR core, including the control blade and channel box structures, fuel rods, fuel canister nosepieces, control blade velocity limiter, and fuel support pieces, in order to investigate a key core melt progression uncertainty for BWR Station Blackout type accidents. The purpose of this experiment program is to examine the behavior of downward-draining molten metallic core materials in a severe reactor accident in a dry BWR core, and to determine conditions under which the molten materials drain out of the core region, or freeze to form blockages in the lower portion of the core. In the event that the draining metallic materials do not form stable blockages in the lower core region, and instead erode the lower core structures such as the lower core plate, then the subsequent core melt progression processes may proceed quite differently than was observed in the TMI-2 accident, with correspondingly different impact on vessel loading and vessel release behavior. The results of the Ex-Reactor tests are preliminary. All of the tests conducted have shown a significant degree of channel box destruction induced by the draining control blade materials. The XR2-1 test further showed that the draining zircaloy melt causes significant disruption of the fuel rod geometry. All of the tests have shown tendencies to form interim blockages as the melts temporarily freeze, but that these blockages re-melt, assisted by eutectic interactions, resulting in the sudden draining of accumulated metallic melt pools.

  19. The Geoengineering Model Intercomparison Project Phase 6 (GeoMIP6: simulation design and preliminary results

    Directory of Open Access Journals (Sweden)

    B. Kravitz

    2015-10-01

    Full Text Available We present a suite of new climate model experiment designs for the Geoengineering Model Intercomparison Project (GeoMIP. This set of experiments, named GeoMIP6 (to be consistent with the Coupled Model Intercomparison Project Phase 6, builds on the previous GeoMIP project simulations, and has been expanded to address several further important topics, including key uncertainties in extreme events, the use of geoengineering as part of a portfolio of responses to climate change, and the relatively new idea of cirrus cloud thinning to allow more longwave radiation to escape to space. We discuss experiment designs, as well as the rationale for those designs, showing preliminary results from individual models when available. We also introduce a new feature, called the GeoMIP Testbed, which provides a platform for simulations that will be performed with a few models and subsequently assessed to determine whether the proposed experiment designs will be adopted as core (Tier 1 GeoMIP experiments. This is meant to encourage various stakeholders to propose new targeted experiments that address their key open science questions, with the goal of making GeoMIP more relevant to a broader set of communities.

  20. The Geoengineering Model Intercomparison Project Phase 6 (GeoMIP6): simulation design and preliminary results

    Science.gov (United States)

    Kravitz, B.; Robock, A.; Tilmes, S.; Boucher, O.; English, J. M.; Irvine, P. J.; Jones, A.; Lawrence, M. G.; MacCracken, M.; Muri, H.; Moore, J. C.; Niemeier, U.; Phipps, S. J.; Sillmann, J.; Storelvmo, T.; Wang, H.; Watanabe, S.

    2015-10-01

    We present a suite of new climate model experiment designs for the Geoengineering Model Intercomparison Project (GeoMIP). This set of experiments, named GeoMIP6 (to be consistent with the Coupled Model Intercomparison Project Phase 6), builds on the previous GeoMIP project simulations, and has been expanded to address several further important topics, including key uncertainties in extreme events, the use of geoengineering as part of a portfolio of responses to climate change, and the relatively new idea of cirrus cloud thinning to allow more longwave radiation to escape to space. We discuss experiment designs, as well as the rationale for those designs, showing preliminary results from individual models when available. We also introduce a new feature, called the GeoMIP Testbed, which provides a platform for simulations that will be performed with a few models and subsequently assessed to determine whether the proposed experiment designs will be adopted as core (Tier 1) GeoMIP experiments. This is meant to encourage various stakeholders to propose new targeted experiments that address their key open science questions, with the goal of making GeoMIP more relevant to a broader set of communities.

  1. Greenridge Multi-Pollutant Control Project Preliminary Public Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Connell, Daniel P

    2009-01-12

    the commercial readiness of an emissions control system that is specifically designed to meet the environmental compliance requirements of these smaller coal-fired EGUs. The multi-pollutant control system is being installed and tested on the AES Greenidge Unit 4 (Boiler 6) by a team including CONSOL Energy Inc. as prime contractor, AES Greenidge LLC as host site owner, and Babcock Power Environmental Inc. as engineering, procurement, and construction contractor. All funding for the project is being provided by the U.S. Department of Energy, through its National Energy Technology Laboratory, and by AES Greenidge. AES Greenidge Unit 4 is a 107 MW{sub e} (net), 1950s vintage, tangentially-fired, reheat unit that is representative of many of the 440 smaller coal-fired units identified above. Following design and construction, the multi-pollutant control system will be demonstrated over an approximately 20-month period while the unit fires 2-4% sulfur eastern U.S. bituminous coal and co-fires up to 10% biomass. This Preliminary Public Design Report is the first in a series of two reports describing the design of the multi-pollutant control facility that is being demonstrated at AES Greenidge. Its purpose is to consolidate for public use all available nonproprietary design information on the Greenidge Multi-Pollutant Control Project. As such, the report includes a discussion of the process concept, design objectives, design considerations, and uncertainties associated with the multi-pollutant control system and also summarizes the design of major process components and balance of plant considerations for the AES Greenidge Unit 4 installation. The Final Public Design Report, the second report in the series, will update this Preliminary Public Design Report to reflect the final, as-built design of the facility and to incorporate data on capital costs and projected operating costs.

  2. Final definition and preliminary design study for the initial atmospheric cloud physics laboratory, a Spacelab mission payload

    Science.gov (United States)

    1976-01-01

    The following areas related to the final definition and preliminary design study of the initial atmospheric cloud physics laboratory (ACPL) were covered: (1) proposal organization, personnel, schedule, and project management, (2) proposed configurations, (3) study objectives, (4) ACPL experiment program listing and description, (5) mission/flight flexibility and modularity/commonality, (6) study plan, and (7) description of following tasks: requirement analysis and definition task flow, systems analysis and trade studies, subsystem analysis and trade studies, specifications and interface control documents, preliminary design task flow, work breakdown structure, programmatic analysis and planning, and project costs. Finally, an overview of the scientific requirements was presented.

  3. Hierarchical Modeling and Robust Synthesis for the Preliminary Design of Large Scale Complex Systems

    Science.gov (United States)

    Koch, Patrick N.

    1997-01-01

    Large-scale complex systems are characterized by multiple interacting subsystems and the analysis of multiple disciplines. The design and development of such systems inevitably requires the resolution of multiple conflicting objectives. The size of complex systems, however, prohibits the development of comprehensive system models, and thus these systems must be partitioned into their constituent parts. Because simultaneous solution of individual subsystem models is often not manageable iteration is inevitable and often excessive. In this dissertation these issues are addressed through the development of a method for hierarchical robust preliminary design exploration to facilitate concurrent system and subsystem design exploration, for the concurrent generation of robust system and subsystem specifications for the preliminary design of multi-level, multi-objective, large-scale complex systems. This method is developed through the integration and expansion of current design techniques: Hierarchical partitioning and modeling techniques for partitioning large-scale complex systems into more tractable parts, and allowing integration of subproblems for system synthesis; Statistical experimentation and approximation techniques for increasing both the efficiency and the comprehensiveness of preliminary design exploration; and Noise modeling techniques for implementing robust preliminary design when approximate models are employed. Hierarchical partitioning and modeling techniques including intermediate responses, linking variables, and compatibility constraints are incorporated within a hierarchical compromise decision support problem formulation for synthesizing subproblem solutions for a partitioned system. Experimentation and approximation techniques are employed for concurrent investigations and modeling of partitioned subproblems. A modified composite experiment is introduced for fitting better predictive models across the ranges of the factors, and an approach for

  4. Photon Detection System Designs for the Deep Underground Neutrino Experiment

    CERN Document Server

    Whittington, Denver

    2015-01-01

    The Deep Underground Neutrino Experiment (DUNE) will be a premier facility for exploring long-standing questions about the boundaries of the standard model. Acting in concert with the liquid argon time projection chambers underpinning the far detector design, the DUNE photon detection system will capture ultraviolet scintillation light in order to provide valuable timing information for event reconstruction. To maximize the active area while maintaining a small photocathode coverage, the experiment will utilize a design based on plastic light guides coated with a wavelength-shifting compound, along with silicon photomultipliers, to collect and record scintillation light from liquid argon. This report presents recent preliminary performance measurements of this baseline design and several alternative designs which promise significant improvements in sensitivity to low-energy interactions.

  5. Photon Detection System Designs for the Deep Underground Neutrino Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Whittington, Denver [Indiana U.

    2015-11-19

    The Deep Underground Neutrino Experiment (DUNE) will be a premier facility for exploring long-standing questions about the boundaries of the standard model. Acting in concert with the liquid argon time projection chambers underpinning the far detector design, the DUNE photon detection system will capture ultraviolet scintillation light in order to provide valuable timing information for event reconstruction. To maximize the active area while maintaining a small photocathode coverage, the experiment will utilize a design based on plastic light guides coated with a wavelength-shifting compound, along with silicon photomultipliers, to collect and record scintillation light from liquid argon. This report presents recent preliminary performance measurements of this baseline design and several alternative designs which promise significant improvements in sensitivity to low-energy interactions.

  6. Photon detection system designs for the Deep Underground Neutrino Experiment

    Science.gov (United States)

    Whittington, D.

    2016-05-01

    The Deep Underground Neutrino Experiment (DUNE) will be a premier facility for exploring long-standing questions about the boundaries of the standard model. Acting in concert with the liquid argon time projection chambers underpinning the far detector design, the DUNE photon detection system will capture ultraviolet scintillation light in order to provide valuable timing information for event reconstruction. To maximize the active area while maintaining a small photocathode coverage, the experiment will utilize a design based on plastic light guides coated with a wavelength-shifting compound, along with silicon photomultipliers, to collect and record scintillation light from liquid argon. This report presents recent preliminary performance measurements of this baseline design and several alternative designs which promise significant improvements in sensitivity to low-energy interactions.

  7. A dispersion model approach to the preliminary design of adsorber beds for trace contaminants

    Science.gov (United States)

    Madey, R.; Czayka, M.; Forsythe, R.; Povlis, J.; Yin, K.

    1976-01-01

    It is shown that a dispersion model for the transport of a gas through a porous medium can be useful in the preliminary design of adsorber beds for the control of trace contaminants. The transmission function is considered, taking into account the transmission of 102-ppm acetaldehyde in helium flowing at various flow rates through an absorber bed. The experiments were conducted at a temperature of 25.0 C. Attention is given to a representation of the experimental breakthrough curve, the volume adsorption capacity, temperature studies, and correlations.

  8. Cost Optimal System Identification Experiment Design

    DEFF Research Database (Denmark)

    Kirkegaard, Poul Henning

    the experiment design are not based on obtained experimental data. Instead the decisions are based on the expected experimental data assumed to be obtained from the measurements, estimated based on prior information and engineering judgement. The design method provides a system identification experiment design...

  9. An evaluation of the Positive Emotional Experiences Scale: A preliminary analysis

    Directory of Open Access Journals (Sweden)

    Rene van Wyk

    2016-04-01

    Full Text Available Orientation: The positive organisational behaviour movement emphasises the advantages of psychological strengths in business. The psychological virtues of positive emotional experiences can potentially promote human strengths to the advantages of business functioning and the management of work conditions. This is supported by Fredrickson’s broaden-and-build theory that emphasises the broadening of reactive thought patterns through experiences of positive emotions.Research purpose: A preliminary psychometric evaluation of a positive measurement of dimensions of emotional experiences in the workplace, by rephrasing the Kiefer and Barclay Toxic Emotional Experiences Scale.Motivation for the study: This quantitative Exploratory Factor Analysis investigates the factorial structure and reliability of the Positive Emotional Experiences Scale, a positive rephrased version of the Toxic Emotional Experiences Scale.Research approach, design and method: This Exploratory Factor Analysis indicates an acceptable three-factor model for the Positive Emotional Experiences Scale. These three factors are: (1 psychological recurrent positive state, (2 social connectedness and (3 physical refreshed energy, with strong Cronbach’s alphas of 0.91, 0.91 and 0.94, respectively.Main findings: The three-factor model of the Positive Emotional Experiences Scale provides a valid measure in support of Fredrickson’s theory of social, physical and psychological endured personal resources that build positive emotions.Practical/Managerial implications: Knowledge gained on positive versus negative emotional experiences could be applied by management to promote endured personal resources that strengthen positive emotional experiences.Contribution/value-add: The contribution of this rephrased Positive Emotional Experiences Scale provides a reliable measure of assessment of the social, physical and endured psychological and personal resources identified in Fredrickson’s broaden

  10. Adaptive designs for sequential experiments

    Institute of Scientific and Technical Information of China (English)

    林正炎; 张立新

    2003-01-01

    Various adaptive designe have been proposed and applied to clinical trials,bioassay,psycho-physics,etc.Adaptive designs are also useful in high cost engineering trials.More and More people have been paying attention to these desing methods.This paper introduces several broad families of designs,such as the play-the-winner rele,randomized play-the-winner rule and its generalization to the multi-arm case,doubly bi-ased coin adaptive design,Markov chain model.

  11. Preliminary designs for modular OTEC platform station-keeping subsystems. Final report. MR and S Report No. 6042-6

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-02-29

    This volume of the report presents the results of the third through the sixth tasks of the Station Keeping Subsystem (SKSS) design studies for 10/40 MW/sub e/ capacity OTEC Modular Experiment platforms (MEP). Tasks 3 through 6 are: (3) complete preliminary designs for one SKSS for each of the two platforms (SPAR and BARGE); (4) development and testing recommendations for the MEP SKSS; (5) cost-time analysis; and (6) commercial plant recommendations. The overall conclusions and recommendations for the modular, as well as the commercial, OTEC platform station keeping subsystems are delineated. The basic design assumptions made during the process, the technical approach followed, and the results of design iterations, reliability and performance analyses are given. A complete description of the preliminary design SKSS concept is presented. The summary cost estimates for each of the alternative SKSS concepts considered are presented and a time schedule for the recommended concept is provided. The effects of varying some of the important parameters used in SKSS design on the performance and cost of the mooring system are investigated and results presented. The tests required and other developmental recommendations in order to verify and confirm the basic design assumptions are discussed. Finally, the experience gained in the MEP preliminary designs are extended to future commercial OTEC plants' SKSS designs. (WHK)

  12. Summary of the Preliminary Optical ICHMI Design Study: A Preliminary Engineering Design Study for a Standpipe Viewport

    Energy Technology Data Exchange (ETDEWEB)

    Anheier, Norman C.; Qiao, Hong (Amy); Berglin, Eric J.; Hatchell, Brian K.

    2013-12-26

    This summary report examines an in-vessel optical access concept intended to support standoff optical instrumentation, control and human-machine interface (ICHMI) systems for future advanced small modular reactor (AdvSMR) applications. Optical-based measurement and sensing systems for AdvSMR applications have several key benefits over traditional instrumentation and control systems used to monitor reactor process parameters, such as temperature, flow rate, pressure, and coolant chemistry (Anheier et al. 2013). Direct and continuous visualization of the in-vessel components can be maintained using external cameras. Many optical sensing techniques can be performed remotely using open optical beam path configurations. Not only are in-vessel cables eliminated by these configurations, but also sensitive optical monitoring components (e.g., electronics, lasers, detectors, and cameras) can be placed outside the reactor vessel in the instrument vault, containment building, or other locations where temperatures and radiation levels are much lower. However, the extreme AdvSMR environment present challenges for optical access designs and optical materials. Optical access is not provided in any commercial nuclear power plant or featured in any reactor design, although successful implementation of optical access has been demonstrated in test reactors (Arkani and Gharib 2009). This report outlines the key engineering considerations for an AdvSMR optical access concept. Strict American Society of Mechanical Engineers (ASME) construction codes must be followed for any U.S. nuclear facility component (ASME 2013); however, the scope of this study is to evaluate the preliminary engineering issues for this concept, rather than developing a nuclear-qualified design. In addition, this study does not consider accident design requirements. In-vessel optical access using a standpipe viewport concept serves as a test case to explore the engineering challenges and performance requirements

  13. Experimenting with Science Facility Design.

    Science.gov (United States)

    Butterfield, Eric

    1999-01-01

    Discusses the modern school science facility and how computers and teaching methods are changing their design. Issues include power, lighting, and space requirements; funding for planning; architect assessment; materials requirements for work surfaces; and classroom flexibility. (GR)

  14. Preliminary Design Values, U.S., 2015, EPA/OAR/OAQPS/AQAD

    Data.gov (United States)

    U.S. Environmental Protection Agency — This web service contains a map layer with preliminary design values for 2015. In July 2017 the 2015 design values will become official. At that time they will added...

  15. OTEC SKSS preliminary designs. Volume IV. Appendixes. Final report

    Energy Technology Data Exchange (ETDEWEB)

    ,

    1980-02-29

    This volume contains appendices to the Station Keeping Subsystem design study for the 40 MeW Modular Experiment OTEC platforms. Appendices presented include: detailed drag calculations; sample CALMS computer printouts for SPAR and BARGE static analyses; sample time domain computer printouts (Hydromechanics, Inc.) program; extreme value and fatigue load calculations; anchor design calculations; deployment calculations; bottom slope plots; time domain analysis report by Hydromechanics Inc.; detailed cost analysis; control systems study report by Sperry Systems Management; cost estimates for model basin tests; and hydrodynamic loading on the mooring cables. (WHK)

  16. Experiment Design and Analysis Guide - Neutronics & Physics

    Energy Technology Data Exchange (ETDEWEB)

    Misti A Lillo

    2014-06-01

    The purpose of this guide is to provide a consistent, standardized approach to performing neutronics/physics analysis for experiments inserted into the Advanced Test Reactor (ATR). This document provides neutronics/physics analysis guidance to support experiment design and analysis needs for experiments irradiated in the ATR. This guide addresses neutronics/physics analysis in support of experiment design, experiment safety, and experiment program objectives and goals. The intent of this guide is to provide a standardized approach for performing typical neutronics/physics analyses. Deviation from this guide is allowed provided that neutronics/physics analysis details are properly documented in an analysis report.

  17. Preliminary experience with laparoscopic cholecystectomy in a nigerian teaching hospital.

    Science.gov (United States)

    Afuwape, O O; Akute, O O; Adebanjo, A T

    2012-01-01

    Presently many centers have facilities for laparoscopic surgery in Nigeria, but the practice is just evolving in most of these centers. This article presents the preliminary experience of the endoscopic surgery unit (general surgery) at the University College Hospital Ibadan Nigeria. The University College Hospital is the premier Nigerian teaching hospital and is located in the south-western part of the country. All the patients who had laparoscopic cholecystectomy at the University College Hospital between June 2009 and January 2011 were included in this study. The patients' demographic data, diagnosis, results of investigations and intra-operative findings were obtained from the records. Additional information extracted from the records was the duration of surgery, complications, outcome and discharge periods. There were thirteen patients over the twenty month period consisting of twelve females and one male. The age range was twenty six to sixty seven years with a mean of 44.6 years. The duration of surgery ranged from 90 to 189 minutes with a mean of 124 minutes. There were two complications. These were adhesive bowel obstruction and common bile duct injury. The duration of admission ranged from four to thirty two days with a mean of 7.53SD ± 8.5 days. There was one conversion to open surgery due to intra-operative gallbladder perforation with consequent dispersal of multiple gall stones within the peritoneal cavity. The common bile duct injury was diagnosed four days following surgery for which a choledochojejunostomy was done after initial conservative treatment. There was no mortality. Laparoscopic surgery is feasible in Nigeria and is likely to show increasing popularity among patients and surgeons. A careful patient selection protocol is necessary for an acceptable success rate with minimal complications. Our protocol of patient selection eliminated the need for intra-operative common bile duct exploration which requires expensive instruments. However, to

  18. Preliminary Design and Evaluation of Portable Electronic Flight Progress Strips

    Science.gov (United States)

    Doble, Nathan A.; Hansman, R. John

    2002-01-01

    There has been growing interest in using electronic alternatives to the paper Flight Progress Strip (FPS) for air traffic control. However, most research has been centered on radar-based control environments, and has not considered the unique operational needs of the airport air traffic control tower. Based on an analysis of the human factors issues for control tower Decision Support Tool (DST) interfaces, a requirement has been identified for an interaction mechanism which replicates the advantages of the paper FPS (e.g., head-up operation, portability) but also enables input and output with DSTs. An approach has been developed which uses a Portable Electronic FPS that has attributes of both a paper strip and an electronic strip. The prototype flight strip system uses Personal Digital Assistants (PDAs) to replace individual paper strips in addition to a central management interface which is displayed on a desktop computer. Each PDA is connected to the management interface via a wireless local area network. The Portable Electronic FPSs replicate the core functionality of paper flight strips and have additional features which provide a heads-up interface to a DST. A departure DST is used as a motivating example. The central management interface is used for aircraft scheduling and sequencing and provides an overview of airport departure operations. This paper will present the design of the Portable Electronic FPS system as well as preliminary evaluation results.

  19. Platform for dynamic tests: preliminary studies, design and construction

    Directory of Open Access Journals (Sweden)

    J. E. Campuzano

    Full Text Available This paper is about the design and construction of a platform for dynamic tests especially with people jumping, walking, etc. Initially it was tried to find out projects already implemented in platforms and dynamic tests and to study the loads produced by movement of people on slabs and the structural response to these loads. The limits established by different standards have been also studied for these dynamic responses, taking into account the ultimate limit state, as well as the structure in service, since the human body is very sensitive to structural vibrations. Parametric studies were performed considering various configurations of slabs (different spans, thicknesses and conditions of support have been done, looking for a configuration that could have natural frequency close to the frequencies of the human loads. The slab should have dimensions compatible with the available physical space, fundamental frequency below 5 Hz and maximum immediate deflection compatible with the indications of the Brazilian standard NBR6118: 2007. Based on these criteria was chosen a rectangular structure consists of a solid reinforced concrete rectangular slab studded in two opposite edges of steel beams with shear connectors type U. The other two edges are free. The steel beams supporting the slab, in turn, are supported on eight metal profiles (two in each corner of the slab that are supported on two to two short columns of steel profile H. Profiles U in steel are welded to four columns, forming a horizontal frame. Numerical analysis of the dynamic test platform have been performed for free and forced vibration, for obtaining the natural frequencies and corresponding vibration modes, considering the self-weight of the structure and the load that simulates people's weight. After obtaining a structural configuration that fulfilled the stipulated requirements, the design of the slab taking into account the recommendations of the Brazilian standard NBR6118: 2007

  20. Analysis of Design Basis Events in a Preliminary Specific Design of PGSFR

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Kwi Lim; Ha, Kwi Seok [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    KAERI(Korea Atomic Energy Research Institute) has been developing a preliminary specific design of the PGSFR(Prototype Gen-IV Sodium-cooled Fast Reactor), which is a pool type sodium cooled fast reactor with a thermal power of 392.2 MW. Many alterations were made on a preliminary specific design of the PGSFR compared with a conceptual design: a heat removal capability of the DHRS was decreased, the DHXs were submerged in a cold pool, a pressure drop through the core was increased, and a shape of a redon was changed to a peanut type, etc. For identification of safety characteristics including the design changes, 5 DBE's(Design Bases Events) were analyzed using MARS-LMR code. The representative DBE's are TOP(Transient of Over Power), LOF(Loss Of Flow), LOHS(Loss Of Heat Sink), Reactor Vessel Leak and Pipe Break accidents. The representative DBE's were analyzed using the MARS-LMR code. As a result, it was identified that the PGSFR were appropriately tripped by the RPS(Reactor Protection System) and cooled by the DHRS. But a high cladding temperature was estimated in a pipe break accident. Therefore, integrity of the structure should be evaluated in the further study.

  1. Design of experiments in production engineering

    CERN Document Server

    2016-01-01

    This book covers design of experiments (DoE) applied in production engineering as a combination of manufacturing technology with applied management science. It presents recent research advances and applications of design experiments in production engineering and the chapters cover metal cutting tools, soft computing for modelling and optmization of machining, waterjet machining of high performance ceramics, among others.

  2. Smashing UX design foundations for designing online user experiences

    CERN Document Server

    Allen, Jesmond

    2012-01-01

    The ultimate guide to UX from the world's most popular resource for web designers and developers Smashing Magazine is the world's most popular resource for web designers and developers and with this book, the authors provide the pinnacle resource to becoming savvy with User Experience Design (UX). The authors first provide an overview of UX and chart its rise to becoming a valuable and necessary practice for narrowing the gap between Web sites, applications, and users in order to make a user's experience a happy, easy, and successful one.Examines the essential aspects of User Experience Design

  3. Design and analysis of experiments

    CERN Document Server

    Hinkelmann, Klaus

    This book discusses special modifications and extensions of designs that arise in certain fields of application such as genetics, bioinformatics, agriculture, medicine, manufacturing, marketing, etc. Well-known and highly-regarded contributors have written individual chapters that have been extensively reviewed by the Editor to ensure that each individual contribution relates to material found in Volumes 1 and 2 of this book series. The chapters in Volume 3 have an introductory/historical component and proceed to a more advanced technical level to discuss the latest results and future developm

  4. Democratic design experiments: between parliament and laboratory

    DEFF Research Database (Denmark)

    Binder, Thomas; Brandt, Eva; Ehn, Pelle;

    2015-01-01

    been performed and accomplished in participatory practices. In this article we discuss how participatory design may be reinvigorated as a design research programme for democratic design experiments in the light of the de-centring of human-centredness and the foregrounding of collaborative......For more than four decades participatory design has provided exemplars and concepts for understanding the democratic potential of design participation. Despite important impacts on design methodology participatory design has however been stuck in a marginal position as it has wrestled with what has...

  5. Central-receiver solar-thermal power system. Collector subsystem research experiments detail design report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1976-02-24

    The detail design (DD) of research experiment hardware for the collector subsystem (heliostats) to support the 10 MW/sub e/ Pilot Plant preliminary design (PD) is presented. Additionally, test plans for assembly, integration, and array tests are presented, along with results of completed component/material tests. Research experiment DD and tests described were planned to provide design verification and supporting data, with hardware which either duplicates, or closely simulates the Pilot Plant PD baseline. (WHK)

  6. Parametric Fuselage Geometry Generation and Aerodynamic Performance Prediction in Preliminary Rotorcraft Design

    OpenAIRE

    Kunze, Philipp

    2013-01-01

    The creation of an integrated rotorcraft conceptual and preliminary design framework at DLR involved the development of geometry and fuselage aerodynamics modules at the Institute of Aerodynamics and Flow Technology. After a short revision of the RIDE rotorcraft design environment architecture this paper focuses on the implementation of these disciplinary modules. The aim of the geometry module is to bridge the gap between conceptual and preliminary design and to allow for geometry parameter ...

  7. Effect of oxygen manipulations on benthic foraminifera: A preliminary experiment

    Digital Repository Service at National Institute of Oceanography (India)

    Panchang, R.; Nigam, R.; Linshy, V.; Rana, S.S.; Ingole, B.S.

    marine protists, which have a great potential to detect ecological stress at a very early stage. Due to their high fossilization potential, an understanding of the ecology of foraminifera allows interpretations of the past benthic environmental...’. Many soft-shelled forms also exist, but have not been considered in the present study as they have no fossilization potential and thereby of no geological significance. This is a preliminary report and only presents the effect of oxygen...

  8. Preliminary Experiments with XKaapi on Intel Xeon Phi Coprocessor

    OpenAIRE

    Ferreira Lima, Joao Vicente; Broquedis, Francois; Gautier, Thierry; Raffin, Bruno

    2013-01-01

    International audience; This paper presents preliminary performance comparisons of parallel applications developed natively for the Intel Xeon Phi accelerator using three different parallel programming environments and their associated runtime systems. We compare Intel OpenMP, Intel CilkPlus and XKaapi together on the same benchmark suite and we provide comparisons between an Intel Xeon Phi coprocessor and a Sandy Bridge Xeon-based machine. Our benchmark suite is composed of three computing k...

  9. Inverse design-momentum, a method for the preliminary design of horizontal axis wind turbines

    Energy Technology Data Exchange (ETDEWEB)

    Battisti, L [DIMS - Department of Mechanical and Structural Engineering, University of Trento, via Mesiano, 77, 38050 Trento (Italy); Soraperra, G [TOZZI NORD wind turbines, via S. Sebastian s.n.c. 38100 Trento (Italy); Fedrizzi, R [DIMS - Department of Mechanical and Structural Engineering, University of Trento, via Mesiano, 77, 38050 Trento (Italy); Zanne, L [DIMS - Department of Mechanical and Structural Engineering, University of Trento, via Mesiano, 77, 38050 Trento (Italy)

    2007-07-15

    Wind turbine rotor prediction methods based on generalized momentum theory BEM routinely used in industry and vortex wake methods demand the use of airfoil tabulated data and geometrical specifications such as the blade spanwise chord distribution. They belong to the category of 'direct design' methods. When, on the other hand, the geometry is deduced from some design objective, we refer to 'inverse design' methods. This paper presents a method for the preliminary design of wind turbine rotors based on an inverse design approach. For this purpose, a generalized theory was developed without using classical tools such as BEM. Instead, it uses a simplified meridional flow analysis of axial turbomachines and is based on the assumption that knowing the vortex distribution and appropriate boundary conditions is tantamount to knowing the velocity distribution. The simple conservation properties of the vortex components consistently cope with the forces and specific work exchange expressions through the rotor. The method allows for rotor arbitrarily radial load distribution and includes the wake rotation and expansion. Radial pressure gradient is considered in the wake. The capability of the model is demonstrated first by a comparison with the classical actuator disk theory in investigating the consistency of the flow field, then the model is used to predict the blade planform of a commercial wind turbine. Based on these validations, the authors postulate the use of a different vortex distribution (i.e. not-uniform loading) for blade design and discuss the effect of such choices on blade chord and twist, force distribution and power coefficient. In addition to the method's straightforward application to the pre-design phase, the model clearly shows the link between blade geometry and performance allowing quick preliminary evaluation of non uniform loading on blade structural characteristics.

  10. Eye tracking in user experience design

    CERN Document Server

    Romano Bergstorm, Jennifer

    2014-01-01

    Eye Tracking for User Experience Design explores the many applications of eye tracking to better understand how users view and interact with technology. Ten leading experts in eye tracking discuss how they have taken advantage of this new technology to understand, design, and evaluate user experience. Real-world stories are included from these experts who have used eye tracking during the design and development of products ranging from information websites to immersive games. They also explore recent advances in the technology which tracks how users interact with mobile devices, large-screen displays and video game consoles. Methods for combining eye tracking with other research techniques for a more holistic understanding of the user experience are discussed. This is an invaluable resource to those who want to learn how eye tracking can be used to better understand and design for their users. * Includes highly relevant examples and information for those who perform user research and design interactive experi...

  11. The Ethics of User Experience Design

    DEFF Research Database (Denmark)

    Vistisen, Peter; Jensen, Thessa

    actions to experience the system, and thus deal with the problem. The way these actions are related to the way the user is viewed by the designer, will in this article be discussed with the term empathy as its fulcrum. Empathy has been heralded as the primary skill for the user-centered designer to ensure......-centered design process. Exemplifying the differences and ethical implications for the designer in the interaction with the user through the design of interactive digital systems. Finally the article discusses the need to understand design as a development of empathy for a given user or group of users by giving...... a cased-based overview of how empathy can be achieved during the design process, and become the catalyst of a more ethical approach to designing the user experience of ICT....

  12. The Ethics of User Experience Design

    DEFF Research Database (Denmark)

    Vistisen, Peter; Jensen, Thessa

    2013-01-01

    actions to experience the system, and thus deal with the problem. The way these actions are related to the way the user is viewed by the designer, will in this article be discussed with the term empathy as its fulcrum. Empathy has been heralded as the primary skill for the user-centered designer to ensure......-centered design process. Exemplifying the differences and ethical implications for the designer in the interaction with the user through the design of interactive digital systems. Finally the article discusses the need to understand design as a development of empathy for a given user or group of users by giving...... a cased-based overview of how empathy can be achieved during the design process, and become the catalyst of a more ethical approach to designing the user experience of ICT....

  13. Spaceflight payload design flight experience G-408

    Science.gov (United States)

    Durgin, William W.; Looft, Fred J.; Sacco, Albert, Jr.; Thompson, Robert; Dixon, Anthony G.; Roberti, Dino; Labonte, Robert; Moschini, Larry

    1992-01-01

    Worcester Polytechnic Institute's first payload of spaceflight experiments flew aboard Columbia, STS-40, during June of 1991 and culminated eight years of work by students and faculty. The Get Away Special (GAS) payload was installed on the GAS bridge assembly at the aft end of the cargo bay behind the Spacelab Life Sciences (SLS-1) laboratory. The Experiments were turned on by astronaut signal after reaching orbit and then functioned for 72 hours. Environmental and experimental measurements were recorded on three cassette tapes which, together with zeolite crystals grown on orbit, formed the basis of subsequent analyses. The experiments were developed over a number of years by undergraduate students meeting their project requirements for graduation. The experiments included zeolite crystal growth, fluid behavior, and microgravity acceleration measurement in addition to environmental data acquisition. Preparation also included structural design, thermal design, payload integration, and experiment control. All of the experiments functioned on orbit and the payload system performed within design estimates.

  14. Preliminary verification of structure design for CN HCCB TBM with 1 × 4 configuration

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Zhou, E-mail: zhaozhou@swip.ac.cn; Zhou, Bing; Wang, Qijie; Cao, Qixiang; Feng, Kaiming; Wang, Xiaoyu; Zhang, Guoshu

    2016-02-15

    Highlights: • A new and simplification structural design scheme with 1 × 4 configuration is proposed for CN HCCB TBM. • The detail conceptual structural design for 1 × 4 TBM is completed. • The preliminary hydraulic analysis, thermo-hydraulic analysis and structural analysis for 1 × 4 TBM had been carried out. - Abstract: Based on the conceptual design of CN HCCB TBM with 1 × 4 configuration, the preliminary hydraulic analysis, thermo-hydraulic analysis and structural analysis had been carried out for it. Hydraulic and thermo-hydraulic analyses show that the coolant manifold system could meet the fluid design requirement preliminarily and the temperature of RAFMs structural parts, Be and Li{sub 4}SiO{sub 4} pebble beds are within the allowable range, and no zone shows a stress higher than the allowable limit in the preliminary structural analysis. These results indicate the design for CN HCCB TBM with 1 × 4 configuration is preliminary reasonable.

  15. Drain Tank Information for Developing Design Basis of the Preliminary Design

    Energy Technology Data Exchange (ETDEWEB)

    Ferrada, Juan J [ORNL

    2012-02-01

    Tokamak Cooling Water System (TCWS) drain tanks (DTs) serve two functions: normal operation and safety operation. Normal DTs are used for regular maintenance operations when draining is necessary. Safety DTs are used to receive the water leaked into the Vacuum Vessel (VV) after an in-vessel loss of coolant accident (LOCA) event. The preliminary design of the DTs shall be based on the information provided by this document. The capacity of the normal DTs is estimated based on the internal volume of in-vessel components [e.g., First Wall/Blanket (FW/BLK) and Divertor (DIV)]; Neutral Beam Injector (NBI) components; and TCWS piping, heat exchangers, electric heaters, pump casing, pressurizers, and valves. Water volumes have been updated based on 2004-design information, changes adopted because of approved Project Change Requests (PCRs), and data verification by US ITER and AREVA Federal Services, the US ITER A and E Company. Two tanks will store water from normal draining operations of the FW/BLK and DIV Primary Heat Transfer Systems (PHTSs). One tank will store water from normal draining operations of the NBI PHTS. The capacity of the safety DTs is based on analysis of a design basis accident: a large leak from in-vessel components. There are two safety DTs that will receive water from a VV LOCA event and drainage from the VV, as needed. In addition, there is one sump tank for the DIV that will be used for collecting drain water from the draining and drying processes and specifically for draining the DIV system as the DIV cassette lines are at a lower elevation than the DT connection point. Information documented in this report must be refined and verified during the preliminary design of the DTs, and there are several aspects to be considered to complete the preliminary design. Input to these design considerations is discussed in this report and includes, but is not limited to, water inventory; operating procedures/maintenance; Failure Modes and Effects Analysis (FMEA

  16. Drain Tank Information for Developing Design Basis of the Preliminary Design - R00

    Energy Technology Data Exchange (ETDEWEB)

    Ferrada, Juan J [ORNL

    2011-01-01

    Tokamak Cooling Water System (TCWS) drain tanks (DTs) serve two functions: normal operation and safety operation. Normal DTs are used for regular maintenance operations when draining is necessary. Safety DTs are used to receive the water leaked into the Vacuum Vessel (VV) after an in-vessel loss of cooling accident (LOCA) event. The preliminary design of the DTs shall be based on the information provided by this document. The capacity of the normal DTs is estimated based on the internal volume of in-vessel components [e.g., First Wall/Blanket (FW/BLK) and Divertor (DIV)], Neutral Beam Injector (NBI) components, and TCWS piping, heat exchangers, electric heaters, pump casing, pressurizers, and valves. Water volumes have been updated based on 2004 design information, changes adopted because of approved Project Change Requests (PCRs), and data verification by U.S. ITER. Two tanks will store water from normal draining operations of the FW/BLK and DIV Primary Heat Transfer Systems (PHTSs). One tank will store water from normal draining operations of the NBI PHTS. The capacity of the safety DTs is based on analysis of a design-basis accident:1 a large leak from in-vessel components. There are two safety DTs that will receive water from a VV LOCA event and drainage from the VV, as needed. In addition, there is one sump tank for the DIV that will be used for collecting drain water from the draining and drying processes and specifically for draining the DIV system as the DIV cassettes lines are at a lower elevation than the DT connection point. Information documented in this report must be refined and verified during the preliminary design of the DTs, and there are several aspects to be considered to complete the preliminary design. Input to these design considerations is discussed in this report and includes, but is not limited to, water inventory; operating procedures/maintenance; Failure Modes and Effects Analysis (FMEA); tank layout anddimensions, including design

  17. Design for experience where technology meets design and strategy

    CERN Document Server

    Kim, Jinwoo

    2015-01-01

    Presents a strategic perspective and design methodology that guide the process of developing digital products and services that provide 'real experience' to users. Only when the material experienced runs its course to fulfilment is it then regarded as 'real experience' that is distinctively senseful, evaluated as valuable, and harmoniously related to others. Based on the theoretical background of human experience, the book focuses on these three questions: How can we understand the current dominant designs of digital products and services? What are the user experience factor

  18. Novel modular 2-DOF microsurgical forceps for transoral laser microsurgeries: Ergonomic design and preliminary evaluation.

    Science.gov (United States)

    Chauhan, Manish; Barresi, Giacinto; Deshpande, Nikhil; Caldwell, Darwin G; Mattos, Leonardo S

    2016-08-01

    Transoral Laser Microsurgeries (TLM) demand a great level of control and precision in intraoperative tissue manipulation. The optimal eradication of the diseased tissue is possible only with coordinated control of the laser aiming for incision and the microsurgical tools for orienting and stretching the tissue. However, the traditional microsurgical tools are long, single purpose, one degree-of-freedom (DOF), rigid tools with small range of motion and a normal grasping handle inducing non-ergonomic usage. This paper presents a novel, modular microsurgical tool to overcome the challenges of the traditional tools and improve the surgeon-tool usage experience. The novel design adds a rotational DOF to expand the reach and functionality of the tool. The device is provided with an ergonomic grasping handle that avoids extreme wrist excursions and is capable of adapting to the variety of tools used in TLM within the same design. The performance of the new microsurgical tool was evaluated through a subjective assessment with both medical students and expert surgeons. The evaluation demonstrated a general acceptance of the new forceps tool, with the expert surgeons providing positive appraisals for the improved functionality and user experience with the tool, which indicates towards the potential suitability of the device for TLM. The parameters assessed in the preliminary evaluation not only provide a sense of the advantages of the novel design, but also guide future evolution of the tool design.

  19. Preliminary experience with biodegradable implants for fracture fixation

    Directory of Open Access Journals (Sweden)

    Dhillon Mandeep

    2008-01-01

    Full Text Available Background: Biodegradable implants were designed to overcome the disadvantages of metal-based internal fixation devices. Although they have been in use for four decades internationally, many surgeons in India continue to be skeptical about the mechanical strength of biodegradable implants, hence this study. Materials and Methods: A prospective study was done to assess the feasibility and surgeon confidence level with biodegradable implants over a 12-month period in an Indian hospital. Fifteen fractures (intra-articular, metaphyseal or small bone fractures were fixed with biodegradable implants. The surgeries were randomly scheduled so that different surgeons with different levels of experience could use the implants for fixation. Results: Three fractures (one humeral condyle, two capitulum, were supplemented by additional K-wires fixation. Trans-articular fixator was applied in two distal radius and two pilon fractures where bio-pins alone were used. All fractures united, but in two cases the fracture displaced partially during the healing phase; one fibula due to early walking, and one radius was deemed unstable even after bio-pin and external fixator. Conclusions: Biodegradable -implants are excellent for carefully selected cases of intra-articular fractures and some small bone fractures. However, limitations for use in long bone fractures persist and no great advantage is gained if a "hybrid" composite is employed. The mechanical properties of biopins and screws in isolation are perceived to be inferior to those of conventional metal implants, leading to low confidence levels regarding the stability of reduced fractures; these implants should be used predominantly in fracture patterns in which internal fixation is subjected to minimal stress.

  20. Design -|+ Negative emotions for positive experiences

    NARCIS (Netherlands)

    Fokkinga, S.F.

    2015-01-01

    Experience-driven design considers all aspects of a product – its appearance, cultural meaning, functionality, interaction, usability, technology, and indirect consequences of use – with the aim to optimize and orchestrate all these aspects and create the best possible user experience. Since the lat

  1. Preliminary results of the scientific experiments on the Kosmos-936 biosatellite

    Science.gov (United States)

    1977-01-01

    The scientific equipment and experiments on the Kosmos-936 biosatellite are described, including various ground controls and the lab unit for studies at the descent vehicle landing site. Preliminary results are presented of the physiological experiment with rats, biological experiments with drosophila and higher and lower plants, and radiation physics and radiobiology studies for the planning of biological protection on future space flights. The most significant conclusion from the preliminary data is that rats tolerate space flight better with an artificial force of gravity.

  2. Cooperative adaptive cruise control: design and experiments

    NARCIS (Netherlands)

    Naus, G.; Vugts, R.; Ploeg, J.; Molengraft, R. van de; Steinbuch, M.

    2010-01-01

    The design of a CACC system and corresponding experiments are presented. The design targets string stable system behavior, which is assessed using a frequency-domain-based approach. Following this approach, it is shown that the available wireless information enables small inter-vehicle distances, wh

  3. Optimized Experiment Design for Marine Systems Identification

    DEFF Research Database (Denmark)

    Blanke, M.; Knudsen, Morten

    1999-01-01

    Simulation of maneuvring and design of motion controls for marine systems require non-linear mathematical models, which often have more than one-hundred parameters. Model identification is hence an extremely difficult task. This paper discusses experiment design for marine systems identification...

  4. Resourcing of Experience in Co-Design

    DEFF Research Database (Denmark)

    Ylirisku, Salu; Revsbæk, Line; Buur, Jacob

    2017-01-01

    , knowledge to benefit its cultivation is expected to be highly valuable in contemporary multi-cultural design work. This paper approaches the study of the involvement of various stakeholders in design projects through a lens of resourcing experience. Building from G. H. Mead’s pragmatist theory, we devise...

  5. Adaptive Design of Visual Perception Experiments

    Science.gov (United States)

    2010-04-01

    the same treatment type, and the image stimuli within the cells are presented in random order. 2c. Calibrated perception laboratory The...Adaptive design of visual perception experiments John D. O’Connor, Jonathon Hixson US ARMY RDECOM CERDEC NVESD Ft. Belvoir, VA 22060...ABSTRACT Meticulous experimental design may not always prevent confounds from affecting experimental data acquired during visual perception

  6. Cooperative adaptive cruise control: design and experiments

    NARCIS (Netherlands)

    Naus, G.; Vugts, R.; Ploeg, J.; Molengraft, R. van de; Steinbuch, M.

    2010-01-01

    The design of a CACC system and corresponding experiments are presented. The design targets string stable system behavior, which is assessed using a frequency-domain-based approach. Following this approach, it is shown that the available wireless information enables small inter-vehicle distances, wh

  7. Current Mooring Design in Partner WECs and Candidates for Preliminary Analysis

    DEFF Research Database (Denmark)

    Thomsen, Jonas Bjerg; Ferri, Francesco; Kofoed, Jens Peter

    This report is the combined report of Commercial Milestone "CM1: Design and Cost of Current Mooring Solutions of Partner WECs" and Milestone "M3: Mooring Solutions for Preliminary Analysis" of the EUDP project "Mooring Solutions for Large Wave Energy Converters". The report covers a description...... of the current mooring design of the partner Wave Energy Converter (WEC) developers in the project, together with a preliminary cost estimate of the systems....

  8. A Preliminary Rubric Design to Evaluate Mixed Methods Research

    Science.gov (United States)

    Burrows, Timothy J.

    2013-01-01

    With the increase in frequency of the use of mixed methods, both in research publications and in externally funded grants there are increasing calls for a set of standards to assess the quality of mixed methods research. The purpose of this mixed methods study was to conduct a multi-phase analysis to create a preliminary rubric to evaluate mixed…

  9. Preliminary Design Study of a Hybrid Airship for Flight Research

    Science.gov (United States)

    Browning, R. G. E.

    1981-01-01

    The feasibility of using components from four small helicopters and an airship envelope as the basis for a quad-rotor research aircraft was studied. Preliminary investigations included a review of candidate hardware and various combinations of rotor craft/airship configurations. A selected vehicle was analyzed to assess its structural and performance characteristics.

  10. A Preliminary Rubric Design to Evaluate Mixed Methods Research

    Science.gov (United States)

    Burrows, Timothy J.

    2013-01-01

    With the increase in frequency of the use of mixed methods, both in research publications and in externally funded grants there are increasing calls for a set of standards to assess the quality of mixed methods research. The purpose of this mixed methods study was to conduct a multi-phase analysis to create a preliminary rubric to evaluate mixed…

  11. Trade-off results and preliminary designs of Near-Term Hybrid Vehicles

    Science.gov (United States)

    Sandberg, J. J.

    1980-01-01

    Phase I of the Near-Term Hybrid Vehicle Program involved the development of preliminary designs of electric/heat engine hybrid passenger vehicles. The preliminary designs were developed on the basis of mission analysis, performance specification, and design trade-off studies conducted independently by four contractors. THe resulting designs involve parallel hybrid (heat engine/electric) propulsion systems with significant variation in component selection, power train layout, and control strategy. Each of the four designs is projected by its developer as having the potential to substitute electrical energy for 40% to 70% of the petroleum fuel consumed annually by its conventional counterpart.

  12. Zero-gravity cloud physics laboratory: Experiment program definition and preliminary laboratory concept studies

    Science.gov (United States)

    Eaton, L. R.; Greco, E. V.

    1973-01-01

    The experiment program definition and preliminary laboratory concept studies on the zero G cloud physics laboratory are reported. This program involves the definition and development of an atmospheric cloud physics laboratory and the selection and delineations of a set of candidate experiments that must utilize the unique environment of zero gravity or near zero gravity.

  13. Interactions between piscivores, zooplanktivores and zooplankton in submerged macrophytes : Preliminary observations from enclosure and pond experiments

    DEFF Research Database (Denmark)

    Jacobsen, Lene; Perrow, M.R.; Landkildehus, F.

    1997-01-01

    behavioural changes of zooplanktivores has received little attention, even though this may be an important mechanism in enhancing the stability of submerged macrophytes in shallow lakes. Preliminary observations from an unreplicated large-scale field enclosure experiment and a replicated pond experiment...

  14. Hypersonic drone vehicle design: A multidisciplinary experience

    Science.gov (United States)

    1988-01-01

    UCLA's Advanced Aeronautic Design group focussed their efforts on design problems of an unmanned hypersonic vehicle. It is felt that a scaled hypersonic drone is necesary to bridge the gap between present theory on hypersonics and the future reality of the National Aerospace Plane (NASP) for two reasons: (1) to fulfill a need for experimental data in the hypersonic regime, and (2) to provide a testbed for the scramjet engine which is to be the primary mode of propulsion for the NASP. The group concentrated on three areas of great concern to NASP design: propulsion, thermal management, and flight systems. Problem solving in these areas was directed toward design of the drone with the idea that the same design techniques could be applied to the NASP. A 70 deg swept double-delta wing configuration, developed in the 70's at the NASA Langley, was chosen as the aerodynamic and geometric model for the drone. This vehicle would be air launched from a B-1 at Mach 0.8 and 48,000 feet, rocket boosted by two internal engines to Mach 10 and 100,000 feet, and allowed to cruise under power of the scramjet engine until burnout. It would then return to base for an unpowered landing. Preliminary energy calculations based on flight requirements give the drone a gross launch weight of 134,000 pounds and an overall length of 85 feet.

  15. Preliminary Studies for Three Experiments at Treiman-Yang Criterion

    Science.gov (United States)

    Kres, I. V.; Kondratyev, V. N.; Cherubini, S.; Spitaleri, C.

    2016-05-01

    Nuclear reactions with three bodies in their final state may proceed through different reaction mechanisms. The Feynman graph technique has been widely used to describe such reactions. However, it is very difficult in general to select the graphs that dominate in given process. The Treiman-Yang criterion is one of the most powerful experimental tests for verifying the pole approximation prediction when describing a quasi-free reaction mechanism. We propose the theoretical study of the H2(B10, α Be7)ns, H1(B11, α1α2)αs, He3(Be9, α1α2)αs reactions at different energies. The preliminary study helps to check the existence of a QF channel by using the TY creterion.

  16. Design and preliminary assessment of Vanderbilt hand exoskeleton.

    Science.gov (United States)

    Gasser, Benjamin W; Bennett, Daniel A; Durrough, Christina M; Goldfarb, Michael

    2017-07-01

    This paper presents the design of a hand exoskeleton intended to enable or facilitate bimanual activities of daily living (ADLs) for individuals with chronic upper extremity hemiparesis resulting from stroke. The paper describes design of the battery-powered, self-contained exoskeleton and presents the results of initial testing with a single subject with hemiparesis from stroke. Specifically, an experiment was conducted requiring the subject to repeatedly remove the lid from a water bottle both with and without the hand exoskeleton. The relative times required to remove the lid from the bottles was considerably lower when using the exoskeleton. Specifically, the average amount of time required to grasp the bottle with the paretic hand without the exoskeleton was 25.9 s, with a standard deviation of 33.5 s, while the corresponding average amount of time required to grasp the bottle with the exoskeleton was 5.1 s, with a standard deviation of 1.9 s. Thus, the task time involving the paretic hand was reduced by a factor of five, while the standard deviation was reduced by a factor of 16.

  17. A knowledge-based design framework for airplane conceptual and preliminary design

    Science.gov (United States)

    Anemaat, Wilhelmus A. J.

    The goal of work described herein is to develop the second generation of Advanced Aircraft Analysis (AAA) into an object-oriented structure which can be used in different environments. One such environment is the third generation of AAA with its own user interface, the other environment with the same AAA methods (i.e. the knowledge) is the AAA-AML program. AAA-AML automates the initial airplane design process using current AAA methods in combination with AMRaven methodologies for dependency tracking and knowledge management, using the TechnoSoft Adaptive Modeling Language (AML). This will lead to the following benefits: (1) Reduced design time: computer aided design methods can reduce design and development time and replace tedious hand calculations. (2) Better product through improved design: more alternative designs can be evaluated in the same time span, which can lead to improved quality. (3) Reduced design cost: due to less training and less calculation errors substantial savings in design time and related cost can be obtained. (4) Improved Efficiency: the design engineer can avoid technically correct but irrelevant calculations on incomplete or out of sync information, particularly if the process enables robust geometry earlier. Although numerous advancements in knowledge based design have been developed for detailed design, currently no such integrated knowledge based conceptual and preliminary airplane design system exists. The third generation AAA methods are tested over a ten year period on many different airplane designs. Using AAA methods will demonstrate significant time savings. The AAA-AML system will be exercised and tested using 27 existing airplanes ranging from single engine propeller, business jets, airliners, UAV's to fighters. Data for the varied sizing methods will be compared with AAA results, to validate these methods. One new design, a Light Sport Aircraft (LSA), will be developed as an exercise to use the tool for designing a new airplane

  18. Design of a New Research Reactor: Preliminary Conceptual Design (3rd Year)

    Energy Technology Data Exchange (ETDEWEB)

    Park, Cheol; Lee, B. C.; Chae, H. T. and others

    2006-01-15

    A research reactor design is a kind of integral engineering project and a process to obtain a concrete shape through several years of concept development, conceptual design, basic design and detail design. So it requires close cooperation in various areas as well as lots of manpower and cost. The overall process at each stage may be said to be similar except for some stage-specific works. In 2005 as last year of a concept development stage, investigations on the various concepts of the fuel, reactor structure and systems which can meet the requirements established. The requirements for the process systems and I and C systems have also been embodied. The major tasks planned at the early of 2005 have been performed for each area of reactor design as follows: Establishment of the fuel and reactor core concept, and the core analysis, Preliminary thermal-hydraulic and safety analyses for the conceptual cores, Establishment and improvement of analysis system, Concept developments of the reactor structures and major systems, Test and test plan to verify the developed concepts, International cooperation to establish the foundations for exporting a research reactor.

  19. Preliminary Experience with a New Total Distal Radioulnar Joint Replacement

    Science.gov (United States)

    Ewald, Timothy J.; Skeete, Kshamata; Moran, Steven L.

    2012-01-01

    resurfacing design may provide a means of decreasing pain and restoring DRUJ stability and motion following severe trauma, failed hemiarthroplasty, or failed Sauvé–Kapandji procedure. More experience is needed with this implant to confirm these initial encouraging results. The level of evidence for this study is IV (therapeutic, case series). PMID:23904976

  20. Tractable Experiment Design via Mathematical Surrogates

    Energy Technology Data Exchange (ETDEWEB)

    Williams, Brian J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-02-29

    This presentation summarizes the development and implementation of quantitative design criteria motivated by targeted inference objectives for identifying new, potentially expensive computational or physical experiments. The first application is concerned with estimating features of quantities of interest arising from complex computational models, such as quantiles or failure probabilities. A sequential strategy is proposed for iterative refinement of the importance distributions used to efficiently sample the uncertain inputs to the computational model. In the second application, effective use of mathematical surrogates is investigated to help alleviate the analytical and numerical intractability often associated with Bayesian experiment design. This approach allows for the incorporation of prior information into the design process without the need for gross simplification of the design criterion. Illustrative examples of both design problems will be presented as an argument for the relevance of these research problems.

  1. Hypersonic drone design: A multidisciplinary experience

    Science.gov (United States)

    1988-01-01

    Efforts were focused on design problems of an unmanned hypersonic vehicle. It is felt that a scaled hypersonic drone is necessary to bridge the gap between present theory on hypersonics and the future reality of the National Aerospace Plane (NASP) for two reasons: to fulfill a need for experimental data in the hypersonic regime, and to provide a testbed for the scramjet engine which is to be the primary mode of propulsion for the NASP. Three areas of great concern to NASP design were examined: propulsion, thermal management, and flight systems. Problem solving in these areas was directed towards design of the drone with the idea that the same design techniques could be applied to the NASP. A seventy degree swept double delta wing configuration, developed in the 70's at NASA Langley, was chosen as the aerodynamic and geometric model for the drone. This vehicle would be air-launched from a B-1 at Mach 0.8 and 48,000 feet, rocket boosted by two internal engines to Mach 10 and 100,000 feet, and allowed to cruise under power of the scramjet engine until burnout. It would then return to base for an unpowered landing. Preliminary energy calculations based upon the flight requirements give the drone a gross launch weight of 134,000 lb. and an overall length of 85 feet.

  2. Preliminary results from the {sup 51}Cr neutrino source experiment in GALLEX

    Energy Technology Data Exchange (ETDEWEB)

    Hampel, W.; Heusser, G.; Kiko, J. [Max-Planck-Institut fuer Kernphysik, Heidelberg (Germany)] [and others

    1996-09-01

    The GALLEX collaboration performed a second {sup 51}Cr neutrino source experiment during fall 1995. The full results from this second source experiment will not be available before the end of 1996. Meanwhile, we present a short description and preliminary results in this informal note. The (preliminary) value of the activity obtained form direct measurements has been found equal to (68.7 {+-}0.7) PBq (with 1-sigma error). This value, which is about 10% higher than the activity of the first source, was achieved by optimizing the irradiation conditions in the Silo{acute e} reactor and doing a longer irradiation of the enriched chromium. Preliminary results show that the ratio, R, of the radiochemically determined activity from {sup 71}Ge counting (57.1 {+-} PBq) to the directly measured activity is (0.83 {+-} 0.10). The combined value of R for the two source experiments is (0.92 {+-} 0.08).

  3. Adaptive design of visual perception experiments

    Science.gov (United States)

    O'Connor, John D.; Hixson, Jonathan; Thomas, James M., Jr.; Peterson, Matthew S.; Parasuraman, Raja

    2010-04-01

    Meticulous experimental design may not always prevent confounds from affecting experimental data acquired during visual perception experiments. Although experimental controls reduce the potential effects of foreseen sources of interference, interaction, or noise, they are not always adequate for preventing the confounding effects of unforeseen forces. Visual perception experimentation is vulnerable to unforeseen confounds because of the nature of the associated cognitive processes involved in the decision task. Some confounds are beyond the control of experimentation, such as what a participant does immediately prior to experimental participation, or the participant's attitude or emotional state. Other confounds may occur through ignorance of practical control methods on the part of the experiment's designer. The authors conducted experiments related to experimental fatigue and initially achieved significant results that were, upon re-examination, attributable to a lack of adequate controls. Re-examination of the original results and the processes and events that led to them yielded a second experimental design with more experimental controls and significantly different results. The authors propose that designers of visual perception experiments can benefit from planning to use a test-fix-test or adaptive experimental design cycle, so that unforeseen confounds in the initial design can be remedied.

  4. Optimal design of isotope labeling experiments.

    Science.gov (United States)

    Yang, Hong; Mandy, Dominic E; Libourel, Igor G L

    2014-01-01

    Stable isotope labeling experiments (ILE) constitute a powerful methodology for estimating metabolic fluxes. An optimal label design for such an experiment is necessary to maximize the precision with which fluxes can be determined. But often, precision gained in the determination of one flux comes at the expense of the precision of other fluxes, and an appropriate label design therefore foremost depends on the question the investigator wants to address. One could liken ILE to shadows that metabolism casts on products. Optimal label design is the placement of the lamp; creating clear shadows for some parts of metabolism and obscuring others.An optimal isotope label design is influenced by: (1) the network structure; (2) the true flux values; (3) the available label measurements; and, (4) commercially available substrates. The first two aspects are dictated by nature and constrain any optimal design. The second two aspects are suitable design parameters. To create an optimal label design, an explicit optimization criterion needs to be formulated. This usually is a property of the flux covariance matrix, which can be augmented by weighting label substrate cost. An optimal design is found by using such a criterion as an objective function for an optimizer. This chapter uses a simple elementary metabolite units (EMU) representation of the TCA cycle to illustrate the process of experimental design of isotope labeled substrates.

  5. Advanced tokamak reactors based on the spherical torus (ATR/ST). Preliminary design considerations

    Energy Technology Data Exchange (ETDEWEB)

    Miller, R.L.; Krakowski, R.A.; Bathke, C.G.; Copenhaver, C.; Schnurr, N.M.; Engelhardt, A.G.; Seed, T.J.; Zubrin, R.M.

    1986-06-01

    Preliminary design results relating to an advanced magnetic fusion reactor concept based on the high-beta, low-aspect-ratio, spherical-torus tokamak are summarized. The concept includes resistive (demountable) toroidal-field coils, magnetic-divertor impurity control, oscillating-field current drive, and a flowing liquid-metal breeding blanket. Results of parametric tradeoff studies, plasma engineering modeling, fusion-power-core mechanical design, neutronics analyses, and blanket thermalhydraulics studies are described. The approach, models, and interim results described here provide a basis for a more detailed design. Key issues quantified for the spherical-torus reactor center on the need for an efficient drive for this high-current (approx.40 MA) device as well as the economic desirability to increase the net electrical power from the nominal 500-MWe(net) value adopted for the baseline system. Although a direct extension of present tokamak scaling, the stablity and transport of this high-beta (approx.0.3) plasma is a key unknown that is resoluble only by experiment. The spherical torus generally provides a route to improved tokamak reactors as measured by considerably simplified coil technology in a configuration that allows a realistic magnetic divertor design, both leading to increased mass power density and reduced cost.

  6. Near-term hybrid vehicle program, phase 1. Appendix C: Preliminary design data package

    Science.gov (United States)

    1979-01-01

    The design methodology, the design decision rationale, the vehicle preliminary design summary, and the advanced technology developments are presented. The detailed vehicle design, the vehicle ride and handling and front structural crashworthiness analysis, the microcomputer control of the propulsion system, the design study of the battery switching circuit, the field chopper, and the battery charger, and the recent program refinements and computer results are presented.

  7. Designing (for) experiences in photorealistic VR environments

    Science.gov (United States)

    Carroll, Fiona

    2010-04-01

    This paper investigates the role of aesthetics in the design of "intended" experiences in photorealistic virtual reality (VR) environments. It is motivated by the very notion that the aesthetic potential of photorealistic VR content is, and continues to be, underestimated whilst the emphasis on the development of newer and more efficient visualisation technologies to create new and exciting VR experiences increases. Challenging this, the paper looks beyond the technological (and the more traditional human computer interaction approaches that have primarily focused on the performance and efficiency issues of the technology) in order to explore more human values and the experiential side of VR. It focuses on the design of an "engaged interaction" and in doing so, implements a comparative study to explore how the strategic patterning of the aesthetic elements (particularly colour) within a photorealistic VR environment can allow for the design of a certain experience. In conclusion, the paper demonstrates that aesthetics and the "engaged interaction" can play an important role in getting to the heart of the photorealistic VR "user" experience. It highlights how we might design for (i.e. suggest, coax and guide) an "intended" VR experience.

  8. Preliminary experiments on pharmacokinetic diffuse fluorescence tomography of CT-scanning mode

    Science.gov (United States)

    Zhang, Yanqi; Wang, Xin; Yin, Guoyan; Li, Jiao; Zhou, Zhongxing; Zhao, Huijuan; Gao, Feng; Zhang, Limin

    2016-10-01

    In vivo tomographic imaging of the fluorescence pharmacokinetic parameters in tissues can provide additional specific and quantitative physiological and pathological information to that of fluorescence concentration. This modality normally requires a highly-sensitive diffuse fluorescence tomography (DFT) working in dynamic way to finally extract the pharmacokinetic parameters from the measured pharmacokinetics-associated temporally-varying boundary intensity. This paper is devoted to preliminary experimental validation of our proposed direct reconstruction scheme of instantaneous sampling based pharmacokinetic-DFT: A highly-sensitive DFT system of CT-scanning mode working with parallel four photomultiplier-tube photon-counting channels is developed to generate an instantaneous sampling dataset; A direct reconstruction scheme then extracts images of the pharmacokinetic parameters using the adaptive-EKF strategy. We design a dynamic phantom that can simulate the agent metabolism in living tissue. The results of the dynamic phantom experiments verify the validity of the experiment system and reconstruction algorithms, and demonstrate that system provides good resolution, high sensitivity and quantitativeness at different pump speed.

  9. Augmented Reality Cubes for Cognitive Gaming: Preliminary Usability and Game Experience Testing

    Directory of Open Access Journals (Sweden)

    Costas Boletsis

    2016-03-01

    Full Text Available Early detection is important in dementia care; however, cognitive impairment is still under-recognised and under-diagnosed. Cognitive screening and training are two important preventative treatments, which can lead to early detection of cognitive decline. In this work, the “Cognitive Augmented Reality Cubes” (CogARC system is presented, i.e. a serious game for cognitive training and screening, utilising an interaction technique based on Augmented Reality and the manipulation of tangible, physical objects (cubes. The game is a collection of cognitive mini-games of preventative nature and is, primarily, targeting elderly players (≥60 years old. A preliminary testing was conducted focusing on the game experience that CogARC offers (utilising the In-Game Experience Questionnaire, the usability of the system (using the System Usability Scale, and the specific user observations and remarks, as documented by open, semi-structured interviews.  Overall, CogARC demonstrated satisfying positive responses, however, the negative reactions indicated that there are specific problems with aspects of the interaction technique and a number of mini-games. The open interview shed more light on the specific issues of each mini-game and further interpretation of user interactions. The current study managed to provide interesting insights into the game design elements, integration of Augmented Reality, tangible interaction of the system, and on how elderly players perceive and use those interaction components. 

  10. Preliminary Experiments on the Propagation of Plastic Deformation

    Science.gov (United States)

    2013-04-25

    Burnh:l.m Kelly Assist:J.nt to the Chief 2 Defense and Offense • • .. , . R E _S __ 1 RIC TED ., Preface ’ . The work described ~n this...variance with t he t heoreticall ;J- obta i ned curves and , hence, needs f~ther explanation. The object of the experiment s des cribed in t hi s...quite well with the experiments . The shape of t he pl3.stic wave is at some variance with the theor et i cally obta i ned curves. A.s shown by

  11. Preliminary design report: Babcock and Wilcox BR-100 100-ton rail/barge spent fuel shipping cask

    Energy Technology Data Exchange (ETDEWEB)

    None

    1990-02-01

    The purpose of this document is to provide information on burnup credit as applied to the preliminary design of the BR-100 shipping cask. There is a brief description of the preliminary basket design and the features used to maintain a critically safe system. Following the basket description is a discussion of various criticality analyses used to evaluate burnup credit. The results from these analyses are then reviewed in the perspective of fuel burnups expected to be shipped to either the final repository or a Monitored Retrievable Storage (MRS) facility. The hurdles to employing burnup credit in the certification of any cask are then outlines and reviewed. the last section gives conclusions reached as to burnup credit for the BR-100 cask, based on our analyses and experience. All information in this study refers to the cask configured to transport PWR fuel. Boiling Water Reactor (BWR) fuel satisfies the criticality requirements so that burnup credit is not needed. All calculations generated in the preparation of this report were based upon the preliminary design which will be optimized during the final design. 8 refs., 19 figs., 16 tabs.

  12. Design Experiments and the Generation of Theory

    DEFF Research Database (Denmark)

    Nortvig, Anne-Mette

    2014-01-01

    When blended learning is introduced in professional education with strong traditions of physical activities and face-to-face interactions in the classroom, creation of new learning designs is needed both in the classroom and online. While some educators see the implementation of e......-learning and blended learning as an opportunity to innovate and implement design experiments, others try to defend their teaching against changes and the intrusion of technology in the classroom (Hanson, 2009; Könings, Brand-Gruwel, & van Merriënboer, 2007).In this PhD project, an overall Design-based Research...

  13. Preliminary design of a satellite observation system for Space Station Freedom

    Science.gov (United States)

    Cabe, Greg (Editor); Gallagher, Chris; Wilson, Brian; Rehfeld, James; Maurer, Alexa; Stern, Dan; Nualart, Jaime; Le, Xuan-Trang

    1992-01-01

    Degobah Satellite Systems (DSS), in cooperation with the University Space Research Association (USRA), NASA - Johnson Space Center (JSC), and the University of Texas, has completed the preliminary design of a satellite system to provide inexpensive on-demand video images of all or any portion of Space Station Freedom (SSF). DSS has narrowed the scope of the project to complement the work done by Mr. Dennis Wells at Johnson Space Center. This three month project has resulted in completion of the preliminary design of AERCAM, the Autonomous Extravehicular Robotic Camera, detailed in this design report. This report begins by providing information on the project background, describing the mission objectives, constraints, and assumptions. Preliminary designs for the primary concept and satellite subsystems are then discussed in detail. Included in the technical portion of the report are detailed descriptions of an advanced imaging system and docking and safing systems that ensure compatibility with the SSF. The report concludes by describing management procedures and project costs.

  14. Uniform design of experiments with mixtures

    Institute of Scientific and Technical Information of China (English)

    王元; 方开泰

    1996-01-01

    Consider a design of experiments with mixtures:0≤ai

  15. Design and Analysis of Simulation Experiments

    NARCIS (Netherlands)

    Kleijnen, Jack P.C.

    2015-01-01

    This is a new edition of Kleijnen’s advanced expository book on statistical methods for the Design and Analysis of Simulation Experiments (DASE). Altogether, this new edition has approximately 50% new material not in the original book. More specifically, the author has made significant changes to

  16. Expressions: Embodiment in the experience of design

    NARCIS (Netherlands)

    Van Rompay, T.J.L.

    2005-01-01

    EXPRESSIONS: EMBODIMENT IN THE EXPERIENCE OF DESIGN Products are not just objects by means of which we get things done. Apart from bringing aesthetic pleasures, for instance, they may also embody values we hold dear, communicate our fine taste to others, and help us define who we are. These widely

  17. Preliminary Investigation of the Satellite Gravitational Red Shift Experiment

    Science.gov (United States)

    Zacharias, J. R.; Searle, C. L.; Graham, J. W.; Badessa, R. S.; Bates, V. J.; Kent, R. L.

    1961-01-01

    The work performed under this contract involved study, design, and construction of experimental equipment to perform a short-term measurement of the gravitational red shift. In the system designed, phase comparison techniques are employed so that the time interval required to obtain a single measurement for one altitude is of the order of one minute. An elliptical orbit was chosen to permit measurement of frequency shift as a function of altitude. One particularly attractive orbit is that having a 12-hour orbiting period (perigee, 270 miles, apogee 24,800 miles). This orbit, shown in Fig. 1, allows continuous measurements to be made over an 11-hour interval during which time the altitude is varying greatly. Measurements can not be made for the succeeding 14 hours. Since the variation of frequency difference with altitude is of greatest interest, a fixed offset or a slow drift between the oscillator on the ground and. the oscillator in the satellite will not invalidate the measurements.

  18. Preliminary design report for the K basins integrated water treatment system

    Energy Technology Data Exchange (ETDEWEB)

    Pauly, T.R., Westinghouse Hanford

    1996-08-12

    This Preliminary Design Report (PDR) provides a revised concept for the K Basins Integrated Water Treatment Systems (IWTS). This PDR incorporates the 11 recommendations made in a May 1996 Value Engineering session into the Conceptual Design, and provides new flow diagrams, hazard category assessment, cost estimate, and schedule for the IWTS Subproject.

  19. A Preliminary Study on Gender Differences in Studying Systems Analysis and Design

    Science.gov (United States)

    Lee, Fion S. L.; Wong, Kelvin C. K.

    2017-01-01

    Systems analysis and design is a crucial task in system development and is included in a typical information systems programme as a core course. This paper presented a preliminary study on gender differences in studying a systems analysis and design course of an undergraduate programme. Results indicated that male students outperformed female…

  20. Preliminary results of solar constant observations with the SOLCON experiment on ATLAS-1

    Science.gov (United States)

    Crommelynck, D.; Domingo, V.; Barkstrom, B.; Lee, R. B., II; Donaldson, J.; Telljohann, U; Warren, L.; Fichot, A.

    1994-01-01

    A brief description is given of the Solar Constant (SOLCAN) experiment on Atmospheric Laboratory for Applications and Science (ATLAS) 1, its scientific and technical objectives, as well as its measurement principle and its on board chronology of operations. A preliminary value of the solar constant during the third solar operation of the mission is also provided.

  1. THE MORPHOLOGICAL BASIS FOR OLFACTORY PERCEPTION OF STEROIDS DUING AGONISTIC BEHAVIOR IN LOBSTER: PRELIMINARY EXPERIMENTS

    Science.gov (United States)

    The morphological basis for olfactory perception of steroids during agonistic behavior in lobsters: preliminary experiments. Borsay Horowitz, DJ1, Kass-Simon, G2, Coglianese, D2, Martin, L2, Boseman, M2, Cromarty, S3, Randall, K3, Fini, A.3 1US EPA, NHEERL, ORD, Atlantic Ecology...

  2. Preliminary report on the design of the Superconducting Super Collider

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-01-01

    While a rather detailed Conceptual Design Report will be available in April, an Superconducting Super Collider (SSC) it is appropriate to give a preview, now that the primary parameters for the Conceptual Design Report have been put down. In this preview the leading two chapters give the historical and scientific-technical background for the SSC and deal at somelength with the physics issues to be explored by the SSC. A third chapter reviews briefly the engineering and accelerator physics foundations for the developing SSC design, while the fourth lists the primary design parameters and describes the overall design. The fifth chapter describes briefly the principal engineering systems that will appear in the Conceptual Design Report, including the rather extensive injector system required. A sixth and final chapter outlines the beginnings of a ``construction plan`` put together for the purposes of exploring practical schedules and defining the critical design, development and planning paths for the overall facility and its major sub-systems.

  3. Tuning Parameters in Heuristics by Using Design of Experiments Methods

    Science.gov (United States)

    Arin, Arif; Rabadi, Ghaith; Unal, Resit

    2010-01-01

    With the growing complexity of today's large scale problems, it has become more difficult to find optimal solutions by using exact mathematical methods. The need to find near-optimal solutions in an acceptable time frame requires heuristic approaches. In many cases, however, most heuristics have several parameters that need to be "tuned" before they can reach good results. The problem then turns into "finding best parameter setting" for the heuristics to solve the problems efficiently and timely. One-Factor-At-a-Time (OFAT) approach for parameter tuning neglects the interactions between parameters. Design of Experiments (DOE) tools can be instead employed to tune the parameters more effectively. In this paper, we seek the best parameter setting for a Genetic Algorithm (GA) to solve the single machine total weighted tardiness problem in which n jobs must be scheduled on a single machine without preemption, and the objective is to minimize the total weighted tardiness. Benchmark instances for the problem are available in the literature. To fine tune the GA parameters in the most efficient way, we compare multiple DOE models including 2-level (2k ) full factorial design, orthogonal array design, central composite design, D-optimal design and signal-to-noise (SIN) ratios. In each DOE method, a mathematical model is created using regression analysis, and solved to obtain the best parameter setting. After verification runs using the tuned parameter setting, the preliminary results for optimal solutions of multiple instances were found efficiently.

  4. Preliminary experience with laparoscopic surgery in Ile-Ife, Nigeria.

    Science.gov (United States)

    Adisa, A O; Arowolo, O A; Salako, A A; Lawal, O O

    2009-12-01

    This study presents a pioneer experience with laparoscopic operations in a General Surgical unit of the Obafemi Awolowo University Teaching Hospitals Complex, Ile-Ife, Nigeria. Consecutive patients who had laparoscopic operations from April through December 2008 were prospectively studied. Following clinical diagnosis, initial diagnostic laparoscopy was undertaken in all patients, followed by therapeutic open or laparoscopic procedures. All procedures were done under general anaesthesia. Duration of operation and outcome including complications were recorded. In all, there were 12 patients (8 males, 4 females), aged 15 to 50 years. Eight patients had clinical diagnoses of acute appendicitis, one each had undetermined right lower abdominal pain suspected ectopic gestation, adhesive intestinal obstruction and metastatic liver disease. The first 4 patients with inflammed appendix confirmed at laparoscopy had open appendicectomy. Of the next cohort of 5 patients, laparoscopic appendicectomy was completed in four but converted to open procedure in one. Normal findings were noted in the lady with suspected ectopic gestation. Laparoscopic adhesiolysis was done for adhesive intestinal obstruction while a laparoscopic liver biopsy was done for the patient with metastatic liver disease. Operative time ranged from 55-105 minutes with marked reduction in operation time as confidence and experience grew. No intraoperative complication was observed but one patient had superficial port site infection postoperatively. We conclude that with good patient selection and some improvisation, laparoscopic general surgical operations are feasible with acceptable outcome even in a poor resource setting.

  5. Fort Hood Solar Total Energy Project. Volume II. Preliminary design. Part 1. System criteria and design description. Final report

    Energy Technology Data Exchange (ETDEWEB)

    None,

    1979-01-01

    This volume documents the preliminary design developed for the Solar Total Energy System to be installed at Fort Hood, Texas. Current system, subsystem, and component designs are described and additional studies which support selection among significant design alternatives are presented. Overall system requirements which form the system design basis are presented. These include program objectives; performance and output load requirements; industrial, statutory, and regulatory standards; and site interface requirements. Material in this section will continue to be issued separately in the Systems Requirements Document and maintained current through revision throughout future phases of the project. Overall system design and detailed subsystem design descriptions are provided. Consideration of operation and maintenance is reflected in discussion of each subsystem design as well as in an integrated overall discussion. Included are the solar collector subsystem; the thermal storage subsystem, the power conversion sybsystem (including electrical generation and distribution); the heating/cooling and domestic hot water subsystems; overall instrumentation and control; and the STES building and physical plant. The design of several subsystems has progressed beyond the preliminary stage; descriptions for such subsystems are therefore provided in more detail than others to provide complete documentation of the work performed. In some cases, preliminary design parameters require specific verificaton in the definitive design phase and are identified in the text. Subsystem descriptions will continue to be issued and revised separately to maintain accuracy during future phases of the project. (WHK)

  6. The Thirty Gigahertz Instrument Receiver for the QUIJOTE Experiment: Preliminary Polarization Measurements and Systematic-Error Analysis.

    Science.gov (United States)

    Casas, Francisco J; Ortiz, David; Villa, Enrique; Cano, Juan L; Cagigas, Jaime; Pérez, Ana R; Aja, Beatriz; Terán, J Vicente; de la Fuente, Luisa; Artal, Eduardo; Hoyland, Roger; Génova-Santos, Ricardo

    2015-08-05

    This paper presents preliminary polarization measurements and systematic-error characterization of the Thirty Gigahertz Instrument receiver developed for the QUIJOTE experiment. The instrument has been designed to measure the polarization of Cosmic Microwave Background radiation from the sky, obtaining the Q, U, and I Stokes parameters of the incoming signal simultaneously. Two kinds of linearly polarized input signals have been used as excitations in the polarimeter measurement tests in the laboratory; these show consistent results in terms of the Stokes parameters obtained. A measurement-based systematic-error characterization technique has been used in order to determine the possible sources of instrumental errors and to assist in the polarimeter calibration process.

  7. Preliminary skyshine calculations for the Poloidal Diverter Tokamak Experiment

    Science.gov (United States)

    Nigg, D. W.; Wheeler, F. J.

    1981-01-01

    A calculational model is presented to estimate the radiation dose, due to the skyshine effect, in the control room and at the site boundary of the Poloidal Diverter Experiment (PDX) facility at Princeton University which requires substantial radiation shielding. The required composition and thickness of a water-filled roof shield that would reduce this effect to an acceptable level is computed, using an efficient one-dimensional model with an Sn calculation in slab geometry. The actual neutron skyshine dose is computed using a Monte Carlo model with the neutron source at the roof surface obtained from the slab Sn calculation, and the capture gamma dose is computed using a simple point-kernel single-scatter method. It is maintained that the slab model provides the exact probability of leakage out the top surface of the roof and that it is nearly as accurate as and much less costly than multi-dimensional techniques.

  8. A PRELIMINARY EXPERIMENT ON DENITRIFICATION OF WASTE LANDFILL LEACHATE

    Science.gov (United States)

    Wada, Nariaki; Nakamichi, Tamihiro; Yagi, Masahiro; Matsumoto, Toshihide; Kugimiya, Akikazu; Michioku, Kohji

    A laboratory experiment on denitrification was carried out in order to reduce nitrogen load from municipal landfill leachate. Nitrogen was efficiently removed by feeding sludge of the leachate pond into the tanks, which could activate denitrification bacteria. Although inorganic reducing agent such as iron powder was not able to make the whole water mass anoxic, denitrification took place by supplying organic matters such as methanol, hydrogen feeding agent, etc.. It is considered that small amount of anoxic water film produced on surfaces of container and carriers might contribute to denitrification, although the bulk water is kept aerobic. It is found that organic matters contained in the leachate is so insufficient that nitrification liquid circulation does not work well for denitrification.

  9. Preliminary Results of the Echo-Seeding Experiment ECHO-7 at SLAC

    Energy Technology Data Exchange (ETDEWEB)

    Xiang, D.; Colby, E.; Ding, Y.; Dunning, M.; Frederico, J.; Gilevich, S.; Hast, C.; Jobe, K.; McCormick, D.; Nelson, J.; Raubenheimer, T.O.; Soong, K.; Stupakov, G.; Szalata, Z.; Walz, D.; Weathersby, S.; Woodley, M.; /SLAC; Corlett, J.; Qiang, J.; Penn, G.; Prestemon, S.; /LBL, Berkeley /LPHE, Lausanne

    2010-06-15

    ECHO-7 is a proof-of-principle echo-enabled harmonic generation FEL experiment in the Next Linear Collider Test Accelerator (NLCTA) at SLAC. The experiment aims to generate coherent radiation at 318 nm and 227 nm, which are the 5th and 7th harmonic of the infrared seed laser. In this paper we present the preliminary results from the commissioning run of the completed experimental setup which started in April 2010.

  10. Advanced ISDN satellite designs and experiments

    Science.gov (United States)

    Pepin, Gerard R.

    1992-01-01

    The research performed by GTE Government Systems and the University of Colorado in support of the NASA Satellite Communications Applications Research (SCAR) Program is summarized. Two levels of research were undertaken. The first dealt with providing interim services Integrated Services Digital Network (ISDN) satellite (ISIS) capabilities that accented basic rate ISDN with a ground control similar to that of the Advanced Communications Technology Satellite (ACTS). The ISIS Network Model development represents satellite systems like the ACTS orbiting switch. The ultimate aim is to move these ACTS ground control functions on-board the next generation of ISDN communications satellite to provide full-service ISDN satellite (FSIS) capabilities. The technical and operational parameters for the advanced ISDN communications satellite design are obtainable from the simulation of ISIS and FSIS engineering software models of the major subsystems of the ISDN communications satellite architecture. Discrete event simulation experiments would generate data for analysis against NASA SCAR performance measure and the data obtained from the ISDN satellite terminal adapter hardware (ISTA) experiments, also developed in the program. The Basic and Option 1 phases of the program are also described and include the following: literature search, traffic mode, network model, scenario specifications, performance measures definitions, hardware experiment design, hardware experiment development, simulator design, and simulator development.

  11. Conceptual design of Dipole Research Experiment (DREX)

    Science.gov (United States)

    Qingmei, XIAO; Zhibin, WANG; Xiaogang, WANG; Chijie, XIAO; Xiaoyi, YANG; Jinxing, ZHENG

    2017-03-01

    A new terrella-like device for laboratory simulation of inner magnetosphere plasmas, Dipole Research Experiment, is scheduled to be built at the Harbin Institute of Technology (HIT), China, as a major state scientific research facility for space physics studies. It is designed to provide a ground experimental platform to reproduce the inner magnetosphere to simulate the processes of trapping, acceleration, and transport of energetic charged particles restrained in a dipole magnetic field configuration. The scaling relation of hydromagnetism between the laboratory plasma of the device and the geomagnetosphere plasma is applied to resemble geospace processes in the Dipole Research Experiment plasma. Multiple plasma sources, different kinds of coils with specific functions, and advanced diagnostics are designed to be equipped in the facility for multi-functions. The motivation, design criteria for the Dipole Research Experiment experiments and the means applied to generate the plasma of desired parameters in the laboratory are also described. Supported by National Natural Science Foundation of China (Nos. 11505040, 11261140326 and 11405038), China Postdoctoral Science Foundation (Nos. 2016M591518, 2015M570283) and Project Supported by Natural Scientific Research Innovation Foundation in Harbin Institute of Technology (No. 2017008).

  12. Simulator design for advanced ISDN satellite design and experiments

    Science.gov (United States)

    Pepin, Gerald R.

    1992-01-01

    This simulation design task completion report documents the simulation techniques associated with the network models of both the Interim Service ISDN (integrated services digital network) Satellite (ISIS) and the Full Service ISDN Satellite (FSIS) architectures. The ISIS network model design represents satellite systems like the Advanced Communication Technology Satellite (ACTS) orbiting switch. The FSIS architecture, the ultimate aim of this element of the Satellite Communications Applications Research (SCAR) program, moves all control and switching functions on-board the next generation ISDN communication satellite. The technical and operational parameters for the advanced ISDN communications satellite design will be obtained from the simulation of ISIS and FSIS engineering software models for their major subsystems. Discrete events simulation experiments will be performed with these models using various traffic scenarios, design parameters and operational procedures. The data from these simulations will be used to determine the engineering parameters for the advanced ISDN communications satellite.

  13. Design and analysis of numerical experiments

    Energy Technology Data Exchange (ETDEWEB)

    Bowman, K.P.; Sacks, J.; Chang, Yuefang (Univ. of Illinois, Urbana-Champaign (United States))

    1993-05-01

    Calculations with numerical models are often referred to as numerical experiments, by analogy to classical laboratory experiments. Usually, many numerical experiments are carried out to determine the response of a numerical model to variations of internal or external parameters over some range of interest. If individual experiments are inexpensive to carry out, and if the number of independent parameters is small, it may be possible to search the entire parameter space of the model. This is difficult, however, if the dimension of the parameter space is even moderately large or the codes are expensive to run. In this paper methods are presented for the design and analysis of numerical experiments that are especially useful and efficient in multidimensional parameter spaces. The analysis method, which is similar to kriging in the spatial analysis literature, fits a statistical model to the output of the numerical model. As an example, the method is applied to a fully nonlinear, global, equivalent-barotropic dynamical model. The statistical model also provides estimates of the uncertainty of predicted numerical model output, which can provide guidance on where in the parameter space to conduct further experiments, if necessary. The method can provide major improvements in the efficiency with which numerical sensitivity experiments are conducted. 17 refs., 9 figs., 2 tabs.

  14. DESIGN OF EXPERIMENTS IN TRUCK COMPANY

    Directory of Open Access Journals (Sweden)

    Bibiana Kaselyova

    2015-07-01

    Full Text Available Purpose: Design of experiment (DOE represent very powerful tool for process improvement vastly supported by six sigma methodology. This approach is mostly used by large and manufacturing orientated companies. Presented research is focused on use of DOE in truck company, which is medium size and service orientated. Such study has several purposes. Firstly, detailed description of improvement effort based on DOE can be used as a methodological framework for companies similar to researched one. Secondly, it provides example of successfully implemented low cost design of experiment practise. Moreover, performed experiment identifies key factors, which influence the lifetime of truck tyres.Design/methodology: The research in this paper is based on experiment conducted in Slovakian Truck Company. It provides detailed case study of whole improvement effort, together with problem formulation, design creation and analysis, as well as the results interpretation. The company wants to improve lifetime of the truck tyres. Next to fuel consumption, consumption of tyres and their replacement represent according to them, one of most costly processes in company. Improvement effort was made through the use of PDCA cycle. It start with analysis of current state of tyres consumption. The variability of tyres consumption based on years and types was investigated. Then the causes of tyres replacement were identified and screening DOE was conducted. After a screening design, the full factorial design of experiment was used to identify main drivers of tyres deterioration and breakdowns. Based on result of DOE, the corrective action were propose and implement.Findings: Based on performed experiment our research describes process of tyres use and replacement. It defines main reasons for tyre breakdown and identify main drivers which influence truck tyres lifetime. Moreover it formulates corrective action to prolong tyres lifetime.Originality: The study represents full

  15. Preliminary planning study for safety relief valve experiments in a Mark III BWR pressure suppression system

    Energy Technology Data Exchange (ETDEWEB)

    McCauley, E.W.; Holman, G.S.

    1980-04-21

    In response to a request from the Water Reactor Safety Research Division of the US NRC, a preliminary study is provided which identifies key features and consideration involved in planning a comprehensive in-plant Safety Relief Valve experimental program for a Mark III containment design. The report provides identification of program objectives, measurement system requirements, and some details quantifying expected system response. In addition, a preliminary test matrix is outlined which involves a supporting philosophy intended to enhance the usefulness of the experimental results for all members of the program team: experimentalists, analysts, and plant operator.

  16. New shipyard layout design for the preliminary phase & case study for the green field project

    Directory of Open Access Journals (Sweden)

    Young Joo Song

    2013-03-01

    Full Text Available For several decades, Asian nations such as Korea, Japan and China have been leading the shipbuilding industry since the decline in Europe and America. However, several developing countries such as India, Brazil, etc. are going to make an entrance into the shipbuilding industry. These developing countries are finding technical partners or information providers because they are in situation of little experiences and technologies. Now, the shipbuilding engineering companies of shipbuilding advanced countries are getting a chance of engineering business against those developing countries. The starting point of this business model is green field project for the construction of new shipyard. This business model is started with a design of the shipyard layout. For the conducting of the shipyard layout design, four kinds of engineering parts are required. Those are civil engineering, building engineering, utility engineering and production layout engineering. Among these parts, production layout engineering is most important because its result is the foundation of the other engineering parts and it determines the shipyard capacity during the shipyard operation lifecycle. Previous researches about the shipyard layout design are out of the range from the business requirements because most research cases are in the tower of ivory, which means that there are little consideration of real ship and shipbuilding operation. In this paper, a shipyard layout design for preliminary phase is conducted for the target of newly planned shipyard at Venezuela of South America with an integrated method that is capable of dealing with actual master data from the shipyard. The layout design method of this paper is differentiated from the previous researches in that the actual product data from the target ship and the actual shipbuilding operation data are used for the required area estimation.

  17. Preliminary experiments: High-energy alpha PIXE in archaeometry

    Energy Technology Data Exchange (ETDEWEB)

    Dupuis, Thomas, E-mail: T.Dupuis@ulg.ac.b [Centre Europeen d' Archeometrie, Atomique et Spectroscopie, Universite de Liege, Sart Tilman B15, B-4000 Liege (Belgium); Institut de Physique Nucleaire, Atomique et Spectroscopie, Universite de Liege, Sart Tilman B15, B-4000 Liege (Belgium); Chene, G.; Mathis, F. [Centre Europeen d' Archeometrie, Atomique et Spectroscopie, Universite de Liege, Sart Tilman B15, B-4000 Liege (Belgium); Institut de Physique Nucleaire, Atomique et Spectroscopie, Universite de Liege, Sart Tilman B15, B-4000 Liege (Belgium); Marchal, A.; Philippe, M.; Garnir, H.-P. [Institut de Physique Nucleaire, Atomique et Spectroscopie, Universite de Liege, Sart Tilman B15, B-4000 Liege (Belgium); Strivay, D. [Centre Europeen d' Archeometrie, Atomique et Spectroscopie, Universite de Liege, Sart Tilman B15, B-4000 Liege (Belgium); Institut de Physique Nucleaire, Atomique et Spectroscopie, Universite de Liege, Sart Tilman B15, B-4000 Liege (Belgium)

    2010-06-15

    This paper describes the work realized at the 'Centre Europeen d'Archeometrie' to highlight the utility of high-energy alpha PIXE in the particular field of archaeometry and to introduce the developments done and to be done to complete the knowledge of high-energy alpha PIXE. It starts with the comparison of the yield and the noise background between several alpha particle beams and the comparison between alpha particle and proton beams on different thick and thin references. After, this paper depicts the developments done at the 'Institut de Physique Nucleaire, Atomique et Spectroscopie' to perform such high-energy experiments, first on standards and later on cultural heritage objects. Moreover, it introduces the problematics of such beams for the quantification in PIXE by the intermediary of the knowledge of the ionization and X-ray production cross-sections and also the developments done to answer to this serious lack in the databases.

  18. Mitchell′s technique for epispadias repair: Our preliminary experience

    Directory of Open Access Journals (Sweden)

    Sarin Yogesh

    2006-01-01

    Full Text Available Aim: We present here experience of a single surgeon with Mitchell′s procedure for correction of epispadias. Materials and Methods: Nine boys (mean age 5½ years, range 9 months to 16 years underwent Mitchell′s repair in Department of Pediatric Surgery over a period of 5½ (September 1999 to March 2005 for correction of epispadias. Six of these patients had come for the second stage of exstrophy-epispadias repair after primary bladder closure; the other three had incontinent penopubic epispadias. Results: The penis was cosmetically acceptable as regards to size, glans shape and peno-pubic angle in all the patients. However, there was a high incidence of penopubic fistula (44%. These patients with penopubic fistula also required postoperative urethral dilatations, at times repeated. One of the common factors to these subset patients was their younger age when Mitchell′s urethroplasty was performed. Limitations: The series is descriptive in nature, short in numbers and does not provide statistical comparison of Mitchell′s procedure with the previously done procedures. Conclusions: Mitchell′s complete penile disassembly technique for epispadias repair is more acceptable anatomical procedure that results in near-pendulous penis. However, when performed at young age, it is fraught with the complication of penopubic fistula similar to that as seen with Cantwell-Ransley′s procedure. Mitchell′s procedure creates a hypospadiac meatus initially and the meatal advancement is required as for any other distal penile/coronal hypospadias.

  19. Smart Ultrasound Remote Guidance Experiment (SURGE) Preliminary Findings

    Science.gov (United States)

    Hurst, Victor; Dulchavsky, Scott; Garcia, Kathleen; Sargsyan, Ashot; Ebert, Doug

    2009-01-01

    To date, diagnostic quality ultrasound images were obtained aboard the International Space Station (ISS) using the ultrasound of the Human Research Facility (HRF) rack in the Laboratory module. Through the Advanced Diagnostic Ultrasound in Microgravity (ADUM) and the Braslet-M Occlusion Cuffs (BRASLET SDTO) studies, non-expert ultrasound operators aboard the ISS have performed cardiac, thoracic, abdominal, vascular, ocular, and musculoskeletal ultrasound assessments using remote guidance from ground-based ultrasound experts. With exploration class missions to the lunar and Martian surfaces on the horizon, crew medical officers will necessarily need to operate with greater autonomy given communication delays (round trip times of up to 5 seconds for the Moon and 90 minutes for Mars) and longer periods of communication blackouts (due to orbital constraints of communication assets). The SURGE project explored the feasibility and training requirements of having non-expert ultrasound operators perform autonomous ultrasound assessments in a simulated exploration mission outpost. The project aimed to identify experience, training, and human factors requirements for crew medical officers to perform autonomous ultrasonography. All of these aims pertained to the following risks from the NASA Bioastronautics Road Map: 1) Risk 18: Major Illness and Trauna; 2) Risk 20) Ambulatory Care; 3) Risk 22: Medical Informatics, Technologies, and Support Systems; and 4) Risk 23: Medical Skill Training and Maintenance.

  20. Preliminary safety analysis for key design features of KALIMER

    Energy Technology Data Exchange (ETDEWEB)

    Hahn, D. H.; Kwon, Y. M.; Chang, W. P.; Suk, S. D.; Lee, S. O.; Lee, Y. B.; Jeong, K. S

    2000-07-01

    KAERI is currently developing the conceptual design of a liquid metal reactor, KALIMER(Korea Advanced Liquid Metal Reactor) under the long-term nuclear R and D program. In this report, descriptions of the KALIMER safety design features and safety analyses results for selected ATWS accidents are presented. First, the basic approach to achieve the safety goal is introduced in chapter 1, and the safety evaluation procedure for the KALIMER design is described in chapter 2. It includes event selection, event categorization, description of design basis events, and beyond design basis events. In chapter 3, results of inherent safety evaluations for the KALIMER conceptual design are presented. The KALIMER core and plant system are designed to assure design performance during a selected set of events without either reactor control or protection system intervention. Safety analyses for the postulated anticipated transient without scram(ATWS) have been performed to investigate the KALIMER system response to the events. They are categorized as bounding events(BEs) because of their low probability of occurrence. In chapter 4, the design of the KALIMER containment dome and the results of its performance analysis are presented. The designs of the existing LMR containment and the KALIMER containment dome have been compared in this chapter. Procedure of the containment performance analysis and the analysis results are described along with the accident scenario and source terms. Finally, a simple methodology is introduced to investigate the core kinetics and hydraulic behavior during HCDA in chapter 5. Mathematical formulations have been developed in the framework of the modified bethe-tait method, and scoping analyses have been performed for the KALIMER core behavior during super-prompt critical excursions.

  1. Sonographic appearance of primary thyroid lymphoma-preliminary experience.

    Directory of Open Access Journals (Sweden)

    Yu Xia

    Full Text Available OBJECTIVE: Primary thyroid lymphoma (PTL is an uncommon thyroid malignancy. Despite the rarity of PTL, it is important to recognize PTL promptly because its management differs from that of all the other thyroid neoplasms. This study was designed to investigate the sonographic features of PTL. METHODS: Twenty-seven pathologically confirmed PTLs were categorized into diffuse and non-diffuse type. Sonographic features including thyroid size, thyroid background echotexture, lesion size, echogenecity, calcification, vascularity, cervical lymphadenopathy of each type were retrospectively analyzed. RESULTS: All 27 PTLs were diffuse large B-cell lymphomas and were accompanied by diffuse Hashimoto's thyroiditis. Ten were diffuse type and seventeen were non-diffuse type sonographically. The observations in diffuse group included goiter (10/10, 100.0%, marked echogenesity (10/10, 100.0%, heterogeneous echotexture (10/10, 100.0%, and cervical lymphadenopathy (4/10, 40.0%. The observations in non-diffuse group included marked hypoechogenicity (17/17, 100.0%, heterogeneous background thyroid gland (17/17, 100.0%, goiter (15/17, 88.2%, increased vascularity (8/13, 61.5%, mulifocality (10/17, 58.8%, and cervical lymphadenopathy (7/17, 41.2%. CONCLUSIONS: Although some common features were found, the sonographic appearance of PTL is unspecific, especially for the diffuse type. Therefore, interventional diagnostic procedures should be warranted in the clinical settings when PTL is suspected.

  2. HANARO cooling features: design and experience

    Energy Technology Data Exchange (ETDEWEB)

    Park, Cheol; Chae, Hee-Taek; Han, Gee-Yang; Jun, Byung-Jin; Ahn, Guk-Hoon [HANARO Operating Team, Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-08-01

    In order to achieve the safe core cooling during normal operation and upset conditions, HANARO adopted an upward forced convection cooling system with dual containment arrangements instead of the forced downward flow system popularly used in the majority of forced convection cooling research reactors. This kind of upward flow system was selected by comparing the relative merits of upward and downward flow systems from various points of view such as safety, performance, maintenance. However, several operational matters which were not regarded as serious at design come out during operation. In this paper are presented the design and operational experiences on the unique cooling features of HANARO. (author)

  3. Preliminary Λ ^0 arrow p + π ^- Signal for SELEX - Fermilab Experiment 781

    Science.gov (United States)

    Parkhurst, James F.; Dauwe, Loretta J.; E781 Collaboration

    1997-10-01

    SELEX (SEgmented Large X baryon spectrometer), a fixed target experiment at Fermilab, collected data from February to September 1997, using both 650 GeV/c Σ ^-/π ^-, and 550 GeV/c p/π ^+ beams. This run resulted in 2 billion triggered interactions being logged to tape. Primarily designed to study charmed baryons, E781 can also study hyperon production and decays, and the Primakoff effect. Λ ^0 has several decay modes, however it primarily decays into a p and π ^-. A neutral particle decay to two charged particles appears in the spectrometer as two oppositely charged tracks, originating downstream from the primary interaction in the target. Spectrometer magnets provide a transverse momentum kick which spreads the particle trajectories in a direction depending on the particles' charge. Particle momentum is determined from knowledge of the magnetic field and the track curvature. Assuming masses for the positive and negative tracks, the invariant mass and momentum of the initial neutral particle is calculated. A preliminary reconstruction of Λ ^0 decay, including the mass distribution, will be presented.

  4. CMM Interim Check Design of Experiments (U)

    Energy Technology Data Exchange (ETDEWEB)

    Montano, Joshua Daniel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-07-29

    Coordinate Measuring Machines (CMM) are widely used in industry, throughout the Nuclear Weapons Complex and at Los Alamos National Laboratory (LANL) to verify part conformance to design definition. Calibration cycles for CMMs at LANL are predominantly one year in length and include a weekly interim check to reduce risk. The CMM interim check makes use of Renishaw’s Machine Checking Gauge which is an off-the-shelf product simulates a large sphere within a CMM’s measurement volume and allows for error estimation. As verification on the interim check process a design of experiments investigation was proposed to test a couple of key factors (location and inspector). The results from the two-factor factorial experiment proved that location influenced results more than the inspector or interaction.

  5. DESIGN AND EXPERIMENT OF ELECTRIC BUS

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Performance and reliability experiments on BJD-6100EV electric buses, jointly developed by Beijing Institute of Technology and Beijing Public Transport Company, are introduced. Output power model of battery pack is established and maximum output power is analyzed. A permanent magnetic direct current (PMDC) motor with enhanced windings is developed for the bus. Torque-speed characteristics of the motor are modeled and performance of electric bus is analyzed. Computational method of the range of electric bus is proposed and discussed. Experiments show that electric bus can realize design requirements. Computational methods are verified with the help of field test. It is expected that design and computation method will provide helpful reference to development of electric vehicles.

  6. Preliminary Design and Analysis of ITER In-Wall Shielding

    Institute of Scientific and Technical Information of China (English)

    LIU Changle; YU Jie; WU Songtao; CAI Yingxiang; PAN Wanjiang

    2007-01-01

    ITER in-wall shielding (IIS) is situated between the doubled shells of the ITER Vacuum Vessel (IVV). Its main functions are applied in shielding neutron, gamma-ray and toroidal field ripple reduction. The structure of IIS has been modelled according to the IVV design criteria which has been updated by the ITER team (IT). Static analysis and thermal expansion analysis were performed for the structure. Thermal-hydraulic analysis verified the heat removal capability and resulting temperature, pressure, and velocity changes in the coolant flow. Consequently, our design work is possibly suitable as a reference for IT's updated or final design in its next step.

  7. Preliminary design and optimization of slotted tube grain for solid rocket motor

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    In this paper,design and optimization technique of slotted tube grain for solid rocket motors has been discussed.In doing so,the design objectives and constraints have been set,geometric parameters identified,performance prediction parameters calculated,thereafter preliminary designs completed and finally optimal design reached.Geometric model for slotted tube grain configuration has been developed.Average thrust has been taken as the objective function with constraints of burning time,mass of propellant,fixed length and diameter of chamber case.Lumped parameter method has been used for calculating the performance prediction parameters.A set of preliminary designs has been completed and an analysis of these results conducted.Although all the preliminary results fulfill the design requirements in terms of objective function and constraints,however in order tO attain the optimal design,Sequen-tial quadratic programming optimization technique has been adopted.As the slotted tube grain ge-ometry is totally dependent upon various independent variables and each of these variables has a bearing on explicit characteristic of grain designing,hence affects of the independent variables on performance parameters have been examined,thus variation laws have been developed.Basing on the variation laws and the analysis of preliminary design results,upper and lower limits have been defined for the independent geometric variables and an initial guess provided for conducting optimi-zation.Resuhs attained exhibits that an optimal result has been attained and the value of objective function has been maximized.All the design constraint limits have also been met while ensuring sound values of volumetric loading fraction,web fraction and neutrality.This methodology of design and optimization of slotted tube grain for solid rocket motors can be used by engineers as a reference guide for actual design and engineering purposes.

  8. Preliminary design of an energy storing orthosis for providing gait to people with spinal cord injury.

    Science.gov (United States)

    Boughner, Kyle J; Durfee, William K

    2014-01-01

    A new design is proposed for an energy storing orthosis (ESO) that restores walking to people with spinal cord injury by combining functional electrical stimulation of the quadriceps muscle with a mechanical brace that uses elastic elements to store and transfer energy between hip and knee joints. The new ESO is a variation of a previous design and uses constant force springs for energy storage. Based on the detailed design and on dynamic simulations, the concept has demonstrated preliminary technical feasibility.

  9. Design calculations for NIF convergent ablator experiments

    Directory of Open Access Journals (Sweden)

    Olson R.E.

    2013-11-01

    Full Text Available The NIF convergent ablation tuning effort is underway. In the early experiments, we have discovered that the design code simulations over-predict the capsule implosion velocity and shock flash ρr, but under-predict the hohlraum x-ray flux measurements. The apparent inconsistency between the x-ray flux and radiography data implies that there are important unexplained aspects of the hohlraum and/or capsule behavior.

  10. Evolvable designs of experiments applications for circuits

    CERN Document Server

    Iordache, Octavian

    2009-01-01

    Adopting a groundbreaking approach, the highly regarded author shows how to design methods for planning increasingly complex experiments. He begins with a brief introduction to standard quality methods and the technology in standard electric circuits. The book then gives numerous examples of how to apply the proposed methodology in a series of real-life case studies. Although these case studies are taken from the printed circuit board industry, the methods are equally applicable to other fields of engineering.

  11. Design calculations for NIF convergent ablator experiments

    OpenAIRE

    Olson R.E.; Hicks D.G.; Meezan N.B.; Callahan D.A.; Landen O.L.; Jones O.S.; Langer S.H.; Kline J.L.; Wilson D.C.; Rinderknecht H.; Zylstra A.; Petrasso R.D.

    2013-01-01

    The NIF convergent ablation tuning effort is underway. In the early experiments, we have discovered that the design code simulations over-predict the capsule implosion velocity and shock flash ρr, but under-predict the hohlraum x-ray flux measurements. The apparent inconsistency between the x-ray flux and radiography data implies that there are important unexplained aspects of the hohlraum and/or capsule behavior.

  12. Preliminary Design of an Automated White Board Cleaner

    African Journals Online (AJOL)

    Toshiba

    An International Multidisciplinary Journal, Ethiopia. Vol. 8 (2), Serial No. ... The mechanism of the automated board cleaner entails a horizontal motion. The design is aimed ..... The production cost of chains is relatively high. (ii) The chain drive.

  13. Preliminary of Optical Lens Design for Micro-Satellite

    Science.gov (United States)

    Rachim, Elvira; Mukhtar Tahir, Andi; Herawan, Agus

    2017-01-01

    The development of micro satellites for the last two decades is emerging rapidly as the need of satellite communication usage is increasing. Earth observation is one of the example of how satellites are on demand. Most observation satellites consist of sensors and imaging system on-board. One of the key element to have a good imaging system is a special optical lens system design. Such lens is designed specifically by calculating every parameter such as refractive, reflective indexes, type of surface, distance and many more. Manufactured lenses sometimes do not match the requirement of an imager system hence the special lens design is needed. This paper will first briefly describe the history of optic, theory related to lens system, then the design and the analysis of lens system for micro-satellites generally and LAPAN A4 particularly.

  14. Paradigms for adaptive statistical information designs: practical experiences and strategies.

    Science.gov (United States)

    Wang, Sue-Jane; Hung, H M James; O'Neill, Robert

    2012-11-10

    In the last decade or so, interest in adaptive design clinical trials has gradually been directed towards their use in regulatory submissions by pharmaceutical drug sponsors to evaluate investigational new drugs. Methodological advances of adaptive designs are abundant in the statistical literature since the 1970s. The adaptive design paradigm has been enthusiastically perceived to increase the efficiency and to be more cost-effective than the fixed design paradigm for drug development. Much interest in adaptive designs is in those studies with two-stages, where stage 1 is exploratory and stage 2 depends upon stage 1 results, but where the data of both stages will be combined to yield statistical evidence for use as that of a pivotal registration trial. It was not until the recent release of the US Food and Drug Administration Draft Guidance for Industry on Adaptive Design Clinical Trials for Drugs and Biologics (2010) that the boundaries of flexibility for adaptive designs were specifically considered for regulatory purposes, including what are exploratory goals, and what are the goals of adequate and well-controlled (A&WC) trials (2002). The guidance carefully described these distinctions in an attempt to minimize the confusion between the goals of preliminary learning phases of drug development, which are inherently substantially uncertain, and the definitive inference-based phases of drug development. In this paper, in addition to discussing some aspects of adaptive designs in a confirmatory study setting, we underscore the value of adaptive designs when used in exploratory trials to improve planning of subsequent A&WC trials. One type of adaptation that is receiving attention is the re-estimation of the sample size during the course of the trial. We refer to this type of adaptation as an adaptive statistical information design. Specifically, a case example is used to illustrate how challenging it is to plan a confirmatory adaptive statistical information

  15. Preliminary engineering design of sodium-cooled CANDLE core

    Science.gov (United States)

    Takaki, Naoyuki; Namekawa, Azuma; Yoda, Tomoyuki; Mizutani, Akihiko; Sekimoto, Hiroshi

    2012-06-01

    The CANDLE burning process is characterized by the autonomous shifting of burning region with constant reactivity and constant spacial power distribution. Evaluations of such critical burning process by using widely used neutron diffusion and burning codes under some realistic engineering constraints are valuable to confirm the technical feasibility of the CANDLE concept and to put the idea into concrete core design. In the first part of this paper, it is discussed that whether the sustainable and stable CANDLE burning process can be reproduced even by using conventional core analysis tools such as SLAROM and CITATION-FBR. As a result, it is certainly possible to demonstrate it if the proper core configuration and initial fuel composition required as CANDLE core are applied to the analysis. In the latter part, an example of a concrete image of sodium cooled, metal fuel, 2000MWt rating CANDLE core has been presented by assuming an emerging inevitable technology of recladding. The core satisfies engineering design criteria including cladding temperature, pressure drop, linear heat rate, and cumulative damage fraction (CDF) of cladding, fast neutron fluence and sodium void reactivity which are defined in the Japanese FBR design project. It can be concluded that it is feasible to design CADLE core by using conventional codes while satisfying some realistic engineering design constraints assuming that recladding at certain time interval is technically feasible.

  16. Commercial building design and energy conservation: a preliminary assessment

    Energy Technology Data Exchange (ETDEWEB)

    Nieves, A.; Rosoff, D.

    1982-02-01

    The purpose of the research was to determine the degree of change in commercial building design practice relating to energy conservation since the enactment of the Energy Conservation Standard for New Buildings Act of 1976. Data on current design practices consisted of information from 400 buildings advertised for bids or under construction in 1979 to 1980 on glass in windows and doors, exterior wall systems, roof system, heating plants, and lighting systems. In addition to these building design components, energy conservation measures used included: natural lighting; deadband thermostat; greenhouse-effect atrium collector, heat recovery from the top of the atrium, greenhouse passive heating panels; natural ventilation; insulating shutters, closable skylights, thermal shutters, Trombe wall, corridor trombe; attic ventilation; wind shielding, concrete wall; titlted windows; night flushing cycle; and cooling coils using cooling tower water. A brief explanation of these measures is given. (MCW)

  17. City of Hoboken Energy Surety Analysis: Preliminary Design Summary

    Energy Technology Data Exchange (ETDEWEB)

    Stamp, Jason Edwin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Military and Energy Systems Analysis Dept.; Baca, Michael J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Military and Energy Systems Analysis Dept.; Munoz-Ramos, Karina [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Military and Energy Systems Analysis Dept.; Schenkman, Benjamin L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Military and Energy Systems Analysis Dept.; Eddy, John P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Systems Readiness and Sustainment Technology Dept.; Smith, Mark A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Systems Readiness and Sustainment Technology Dept.; Guttromson, Ross [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Electric Power Systems Research Dept.; Henry, Jordan M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Critical Infrastructure Systems Dept.; Jensen, Richard Pearson [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Geomechanics Dept.

    2014-09-01

    In 2012, Hurricane Sandy devastated much of the U.S. northeast coastal areas. Among those hardest hit was the small community of Hoboken, New Jersey, located on the banks of the Hudson River across from Manhattan. This report describes a city-wide electrical infrastructure design that uses microgrids and other infrastructure to ensure the city retains functionality should such an event occur in the future. The designs ensure that up to 55 critical buildings will retain power during blackout or flooded conditions and include analysis for microgrid architectures, performance parameters, system control, renewable energy integration, and financial opportunities (while grid connected). The results presented here are not binding and are subject to change based on input from the Hoboken stakeholders, the integrator selected to manage and implement the microgrid, or other subject matter experts during the detailed (final) phase of the design effort.

  18. Preliminary design of multi-function LIGA beamline

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    One design of multi-function LIGA beamline has been reported. In this design, two plane mirrors and a series of filters have been employed. One can choose the spectrum range of X-ray easily according to the exposure requirement by adjusting the grazing angle of mirrors and the thickness of filters. And the spot size in the horizontal direction is up to 120mm, which is large enough for exposing 5 inch silicon slice. The typical exposure time is about 1.2h, 1.8h, 0.5h, corresponding to PMMA thickness of 500 μ m, 200 μ m, 20 t m, respectively.

  19. Preliminary Design of IHTS Piping Support for PGSFR

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Nak-Hyun; Koo, Gyeong-Hoi [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    A pipe support is a designed element that transfer the load from pipe to the supporting structures. Providing sufficient pipe wall thickness and installing proper supports are most important elements for structural integrity of the piping system. Piping supports are generally referred to as device used in supporting the weight of the piping. The weight includes that of the pipe proper, the content the pipe carries, and the pipe converting, such as insulation. A FE analysis was performed to select variable spring hanger of IHTS hot-leg piping for PGSFR. The calculated values will be used to design variable spring hanger.

  20. Preliminary Results of the NASA Beacon Receiver for Alphasat Aldo Paraboni TDP5 Propagation Experiment

    Science.gov (United States)

    Nessel, James; Morse, Jacquelynne; Zemba, Michael; Riva, Carlo; Luini, Lorenzo

    2014-01-01

    NASA Glenn Research Center (GRC) and the Politecnico di Milano (POLIMI) have initiated a joint propagation campaign within the framework of the Alphasat propagation experiment to characterize rain attenuation, scintillation, and gaseous absorption effects of the atmosphere in the 40 GHz band. NASA GRC has developed and installed a K/Q-band (20/40 GHz) beacon receiver at the POLIMI campus in Milan, Italy, which receives the 20/40 GHz signals broadcast from the Alphasat Aldo Paraboni TDP#5 beacon payload. The primary goal of these measurements is to develop a physical model to improve predictions of communications systems performance within the Q-band. Herein, we describe the design and preliminary performance of the NASA propagation terminal, which has been installed and operating in Milan since May 2014. The receiver is based upon a validated Fast Fourier Transform (FFT) I/Q digital design approach utilized in other operational NASA propagation terminals, but has been modified to employ power measurement via a frequency estimation technique and to coherently track and measure the amplitude of the 20/40 GHz beacon signals. The system consists of a 1.2-m K-band and a 0.6-m Qband Cassegrain reflector employing synchronous open-loop tracking to track the inclined orbit of the Alphasat satellite. An 8 Hz sampling rate is implemented to characterize scintillation effects, with a 1-Hz measurement bandwidth dynamic range of 45 dB. A weather station with an optical disdrometer is also installed to characterize rain drop size distribution for correlation with physical based models.

  1. TPX: Contractor preliminary design review. Volume 2, PF systems engineering

    Energy Technology Data Exchange (ETDEWEB)

    Calvin, H.A. [Lawrence Livermore National Lab., CA (United States)

    1995-07-28

    This system development specification covers the Poloidal Field (PF) Magnet System, WBS 14 in the Princeton Plasma Physics Laboratory TPX Program to build a tokamak fusion reactor. This specification establishes the performance, design, development and test requirements of the PF Magnet System.

  2. TPX: Contractor preliminary design review. Volume 2, PF systems engineering

    Energy Technology Data Exchange (ETDEWEB)

    Calvin, H.A. [Lawrence Livermore National Lab., CA (United States)

    1995-07-28

    This system development specification covers the Poloidal Field (PF) Magnet System, WBS 14 in the Princeton Plasma Physics Laboratory TPX Program to build a tokamak fusion reactor. This specification establishes the performance, design, development and test requirements of the PF Magnet System.

  3. Preliminary design package for Sunspot Domestic Hot Water Heating System

    Science.gov (United States)

    1976-01-01

    The design review includes a drawing list, auto-control logic, measurement definitions, and other document pertaining to the solar heated prototype hot water systems and two heat exchangers. The hot water systems consist of the following subsystems: collector, storage, control transport, auxiliary energy, and site data acquisition.

  4. Soft Drink Design. USMES Teacher's Resource Book, Preliminary Edition.

    Science.gov (United States)

    Education Development Center, Inc., Newton, MA.

    This USMES unit challenges students to invent a new soft drink that would be popular and produced at a low cost. The teacher resource book for the Soft Drink Design unit contains five sections. The first section describes the USMES approach to student-initiated investigations of real problems, including a discussion of the nature of the USMES…

  5. Preliminary design concept of a subcritical reactor using available resources

    Energy Technology Data Exchange (ETDEWEB)

    Churnetski, E.L. [Oak Ridge Y-12 Plant, TN (United States); Hoyny, V.; Chaudhuri, B.R.; Taprantzis, A.; Yavas, A. [Univ. of Tennessee, Knoxville, TN (United States). Dept. of Nuclear Engineering

    1993-12-31

    During the Fall 1993 semester, a project was initiated within the Nuclear Engineering Department of the University of Tennessee with the objective of developing a design for a subcritical reactor with maximized multiplication factor using materials currently available. Such a device, if constructed, would serve as a teaching tool for the Department of Nuclear Engineering. Design work was conducted as a large number of computer calculations, with trial pile configurations based on fundamental nuclear engineering principles, in an effort to maximize multiplication factor through fuel element geometry, moderator type, fissile/moderator ratio, and reflector character. The principal objective of the design group for the early phase of this project was to present several possible ``baseline`` reactor designs and identify directions for improvements. For the sake of calculational ease, the cores analyzes to date have been of nearly cubic shape. The SCALE CSAS25 software which runs KENO.Va, a Monte Carlo code, was used for all neutronics calculations. The baseline reactors resulting from work to date are cuboidal in shape and graphite reflected. Two types of fuel element geometries are proposed, a typical triangular pitch rod lattice and an arrangement of discrete fuel slugs placed in a lattice corresponding to body centered cubic packing. The latter arrangement provides slightly higher multiplication factors than the former. Calculations were performed for both graphite and heavy water moderation with heavy water moderation producing considerably higher multiplication factors, as expected. In general, the maximum k{sub eff} for the reactors are in the range of 0.5 to 0.9, well subcritical, except in the cases of the extreme possible values of fuel assay where critical configurations are possible. In these cases, designs with reduced fuel loading are recommended to assure a subcritical multiplication factor.

  6. Preliminary safety analysis for key design features of KALIMER-600

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Y. B.; Chang, W. P.; Suk, S. D.; Ha, K. S.; Jeong, H. Y.; Heo, S

    2004-03-01

    KAERI is developing the conceptual design of a Liquid Metal Reactor, KALIMER-600 (Korea Advanced LIquid MEtal Reactor) under the Long-term Nuclear R and D Program. KALIMER-600 addresses key issues regarding future nuclear power plants such as plant safety, economics, proliferation, and waste. In this report, key safety design features are described and safety analyses results for typical ATWS accidents in the KALIMER design with breakeven core are presented. First, the basic approach to achieve the safety goal is introduced in Chapter 1, and the event categorization and acceptance criteria for the KALIMER-600 safety analysis are described in Chapter 2. In Chapter 3, results of inherent safety evaluations for the KALIMER-600 conceptual design are presented. The KALIMER-600 core and plant system are designed to assure benign performance during a selected set of events without either reactor control or protection system intervention. Safety analyses for the postulated Anticipated Transient Without Scram (ATWS) have been performed using the SSC-K code to investigate the KALIMER-600 system response to the events. They are categorized as Bounding Events (BEs) because of their low probability of occurrence. In Chapter 4, the analysis of flow blockage for KALIMER-600 with the MATRA-LMR-FB code, which has been developed for the internal flow blockage in a LMR subassembly. The cases with a blockage of 6-subchannel, 24-subchannel, and 54-subchannel are analyzed.The performance analysis of the KALIMER-600 containment and some evaluations for the behaviors during HCDA will be performed later.

  7. Parameter Screening and Optimisation for ILP Using Designed Experiments

    Science.gov (United States)

    Srinivasan, Ashwin; Ramakrishnan, Ganesh

    Reports of experiments conducted with an Inductive Logic Programming system rarely describe how specific values of parameters of the system are arrived at when constructing models. Usually, no attempt is made to identify sensitive parameters, and those that are used are often given "factory-supplied" default values, or values obtained from some non-systematic exploratory analysis. The immediate consequence of this is, of course, that it is not clear if better models could have been obtained if some form of parameter selection and optimisation had been performed. Questions follow inevitably on the experiments themselves: specifically, are all algorithms being treated fairly, and is the exploratory phase sufficiently well-defined to allow the experiments to be replicated? In this paper, we investigate the use of parameter selection and optimisation techniques grouped under the study of experimental design. Screening and "response surface" methods determine, in turn, sensitive parameters and good values for these parameters. This combined use of parameter selection and response surface-driven optimisation has a long history of application in industrial engineering, and its role in ILP is investigated using two well-known benchmarks. The results suggest that computational overheads from this preliminary phase are not substantial, and that much can be gained, both on improving system performance and on enabling controlled experimentation, by adopting well-established procedures such as the ones proposed here.

  8. Preliminary design studies for a 100 MW Energy Amplifier prototype

    CERN Document Server

    Abánades, A

    2000-01-01

    The Energy Amplifier (EA) is a new concept of fission system based on a subcritical assembly sustained with the neutrons generated by proton beam impact on a heavy element (spallation). This concept, proposed by the Nobel Laureate C. Rubbia (Rubbia, 1995), has remarkable capabilities in the nuclear energy field. First, it can be used to transmute radioactive wastes with a high efficiency alleviating the requirements of the geological repositories, and, second, it provides a massive energy source with the intrinsic safety derived from the use of a subcritical system and an almost null production of long-lived radioactive wastes. EA concept principles have been successfully tested by two experiments at CERN: FEAT (Andriamonge, 1995), that proved there is a net energy gain, by comparing the energy needed by the accelerator with the generated one by fission in the subcritical system. The second experiment, TARC (Abanades, 1997; Arnould, 1999) demonstrated the capability to transmute radioactive elements. The next...

  9. Preliminary design and parametric study of 1400 m partially earth-anchored cable-stayed bridge

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The preliminary design and parametric study of 1400 m partially earth-anchored cable-stayed bridge are described. Static per-formance of this new type of bridge is discussed. Compared with fully self-anchored cable-stayed bridge, its advantages in fin-ished state are summarized. Based on numerical calculation, effects of several structural parameters on static performance are presented.

  10. Hydrogeological characterization of the Heletz Sands Reservoir, Heletz (Israel) as a preliminary step towards CO2 injection experiments

    Science.gov (United States)

    Bensabat, Jacob; Niemi, Auli; Tsang, Chin-Fu; Sharma, Prabhakar; Carrera, Jesus; Sauter, Martin; Tatomir, Alexandru; Ghergut, Julia; Pezard, Philippe; Edlman, Katriona; Brauchler, Ralf

    2013-04-01

    Hydrogeological characterization of the Heletz Sands Reservoir, Heletz (Israel) as a preliminary step towards CO2 injection experiments One the major components of the EU-FP7 funded MUSTANG project is to conduct a highly controlled series of CO2 injection experiments, aimed at determining field values of key CO2 trapping mechanisms such as dissolution and residual trapping and to establish a comprehensive and consistent dataset for model validation. Prior to injecting CO2 there is a need to achieve a sufficient degree of hydrogeological characterization of the reservoir. In what follows we present a sequence of hydrologic tests to be conducted at Heletz and their expected contribution to the understanding relevant hydrogeology. These include: 1) Chemical characterization of the formation fluid; 2) Flowing Fluid Electrical Conductivity log, aimed at determining the vertical variability of the reservoir permeability in the near well vicinity; 3) Water pulse and pumping tests, aimed at determining the reservoir scale hydraulic properties; 4) Thermal test, aimed at determining the value of the heat transfer coefficient from the reservoir to the borehole fluid, which is responsible for the heating of injected fluid in the borehole; 5) two-well injection and pumping of water and tracers test, in order to determine the impact of heterogeneity on the hydraulic parameters and to identify preferential flow paths in the reservoir. This paper presents the design and planning of the experiments, the results obtained in field and a preliminary interpretation.

  11. Preliminary coating design and coating developments for ATHENA

    DEFF Research Database (Denmark)

    Jakobsen, Anders Clemen; Ferreira, Desiree Della Monica; Christensen, Finn Erland

    2011-01-01

    We present initial novel coating design for ATHENA. We make use of both simple bilayer coatings of Ir and B4C and more complex constant period multilayer coatings to enhance the effective area and cover the energy range from 0.1 to 10 keV. We also present the coating technology used for these des......We present initial novel coating design for ATHENA. We make use of both simple bilayer coatings of Ir and B4C and more complex constant period multilayer coatings to enhance the effective area and cover the energy range from 0.1 to 10 keV. We also present the coating technology used...

  12. Yakima/Klickitat Production Preliminary Design Report, Appendix C: Yakima and Klickitat Preliminary Engineering Reports.

    Energy Technology Data Exchange (ETDEWEB)

    CH2M Hill; R.W. Beck and Associates.

    1990-03-01

    This chapter describes the biological and physical fish culture requirements of the hatchery system from which the concepts for the design are formulated. It includes a discussion of the program goals for fish production in the Yakima Basin followed by a brief summary of selected sites. The biological criteria are presented for the water system, adult holding, incubation, rearing, and finally transportation and release. The biological criteria address the water and space requirements, the number and type of vessels, and the related support requirements. To be assured that the components of the system meet all program demands, each life phase from adult capture to the juvenile or smolt transfer into the acclimation sites is analyzed.

  13. Optimal experiment design for time-lapse traveltime tomography

    Energy Technology Data Exchange (ETDEWEB)

    Ajo-Franklin, J.B.

    2009-10-01

    Geophysical monitoring techniques offer the only noninvasive approach capable of assessing both the spatial and temporal dynamics of subsurface fluid processes. Increasingly, permanent sensor arrays in boreholes and on the ocean floor are being deployed to improve the repeatability and increase the temporal sampling of monitoring surveys. Because permanent arrays require a large up-front capital investment and are difficult (or impossible) to re-configure once installed, a premium is placed on selecting a geometry capable of imaging the desired target at minimum cost. We present a simple approach to optimizing downhole sensor configurations for monitoring experiments making use of differential seismic traveltimes. In our case, we use a design quality metric based on the accuracy of tomographic reconstructions for a suite of imaging targets. By not requiring an explicit singular value decomposition of the forward operator, evaluation of this objective function scales to problems with a large number of unknowns. We also restrict the design problem by recasting the array geometry into a low dimensional form more suitable for optimization at a reasonable computational cost. We test two search algorithms on the design problem: the Nelder-Mead downhill simplex method and the Multilevel Coordinate Search algorithm. The algorithm is tested for four crosswell acquisition scenarios relevant to continuous seismic monitoring, a two parameter array optimization, several scenarios involving four parameter length/offset optimizations, and a comparison of optimal multi-source designs. In the last case, we also examine trade-offs between source sparsity and the quality of tomographic reconstructions. One general observation is that asymmetric array lengths improve localized image quality in crosswell experiments with a small number of sources and a large number of receivers. Preliminary results also suggest that high-quality differential images can be generated using only a small

  14. Advanced Reactor Fuels Irradiation Experiment Design Objectives

    Energy Technology Data Exchange (ETDEWEB)

    Chichester, Heather Jean MacLean [Idaho National Lab. (INL), Idaho Falls, ID (United States); Hayes, Steven Lowe [Idaho National Lab. (INL), Idaho Falls, ID (United States); Dempsey, Douglas [Idaho National Lab. (INL), Idaho Falls, ID (United States); Harp, Jason Michael [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-09-01

    This report summarizes the objectives of the current irradiation testing activities being undertaken by the Advanced Fuels Campaign relative to supporting the development and demonstration of innovative design features for metallic fuels in order to realize reliable performance to ultra-high burnups. The AFC-3 and AFC-4 test series are nearing completion; the experiments in this test series that have been completed or are in progress are reviewed and the objectives and test matrices for the final experiments in these two series are defined. The objectives, testing strategy, and test parameters associated with a future AFC test series, AFC-5, are documented. Finally, the future intersections and/or synergies of the AFC irradiation testing program with those of the TREAT transient testing program, emerging needs of proposed Versatile Test Reactor concepts, and the Joint Fuel Cycle Study program’s Integrated Recycle Test are discussed.

  15. Preliminary Axial Flow Turbine Design and Off-Design Performance Analysis Methods for Rotary Wing Aircraft Engines. Part 1; Validation

    Science.gov (United States)

    Chen, Shu-cheng, S.

    2009-01-01

    For the preliminary design and the off-design performance analysis of axial flow turbines, a pair of intermediate level-of-fidelity computer codes, TD2-2 (design; reference 1) and AXOD (off-design; reference 2), are being evaluated for use in turbine design and performance prediction of the modern high performance aircraft engines. TD2-2 employs a streamline curvature method for design, while AXOD approaches the flow analysis with an equal radius-height domain decomposition strategy. Both methods resolve only the flows in the annulus region while modeling the impact introduced by the blade rows. The mathematical formulations and derivations involved in both methods are documented in references 3, 4 for TD2-2) and in reference 5 (for AXOD). The focus of this paper is to discuss the fundamental issues of applicability and compatibility of the two codes as a pair of companion pieces, to perform preliminary design and off-design analysis for modern aircraft engine turbines. Two validation cases for the design and the off-design prediction using TD2-2 and AXOD conducted on two existing high efficiency turbines, developed and tested in the NASA/GE Energy Efficient Engine (GE-E3) Program, the High Pressure Turbine (HPT; two stages, air cooled) and the Low Pressure Turbine (LPT; five stages, un-cooled), are provided in support of the analysis and discussion presented in this paper.

  16. Preliminary Electrical Designs for CTEX and AFIT Satellite Ground Station

    Science.gov (United States)

    2010-03-01

    activated failsafe marker != 0 = 0 Tube 2 Tube 3 Shutdown Describes the primary operation of the experiment control system. [DiS01] Tube Processes: Each...the 400-1,200 nm range. This band is known to contain peaks for Hematites , Geothites and other iron bearing minerals [2]. Looking at this data and...Motion Controllers Motor Amplifier PSU DCCU Power 12-30V DC 56V AC USB General Purpose I/O 32-PIN Proprietary Connection Ethernet Primary Data

  17. Charge generation associated with liquid spraying in tank cleaning and comparable processes - preliminary experiments

    Science.gov (United States)

    Blum, Carsten; Losert, Oswald F. J.

    2015-10-01

    The BG RCI has initiated investigations in order to improve the data basis for assessing the ignition hazard by electrostatic charging processes associated with the spraying of liquids. On the base of preliminary experiments, we established procedures for measurements of electric field strength and charging current in the presence of aerosol particles. Results obtained with three different nozzle types, variation of pressure and with built-in deflecting plate are presented.

  18. Preliminary design study of the Tandem Mirror Reactor (TMR)

    Energy Technology Data Exchange (ETDEWEB)

    Moir, R.W.; Barr, W.L.; Carlson, G.A.

    1978-07-15

    This report describes work done in Fiscal Year 1977 by the Fusion Reactor Studies Group of LLL on the conceptual design of a 1000-MW(e) Tandem Mirror Reactor (TMR). The high Q (defined as the ratio of fusion power to injection power) predicted for the TMR (approximately 5) reduces the recirculating power to a nondominant problem and results in an attractive mirror fusion power plant. The fusion plasma of the TMR is contained in the 100-m-long central cell where the magnetic field strength is a modest 2 T. The blanket for neutron energy recovery and tritium breeding is cylindrical and, along with the solenoidal magnet, is divided into 3-m-long modules to facilitate maintenance. The central cell is fueled (but not heated) by the injection of low-energy neutral beams near its ends. Thus, the central cell is simple and of low technology. The end-cell plasmas must be of high density and high energy in order to plug and heat (via the electrons) the central-cell plasma. The present conceptual design uses 1.2-MeV neutral-beam injection for the end plugs and a cryogenic-aluminum, Yin-Yang magnet that produces an incremental field of about 1 T over a field of 16 T produced by a pair of Nb/sub 3/Sn superconducting solenoids. Important design problems remain in both the neutral-beam injector and in the end-plug magnet. Also remaining are important physics questions such as alpha-beam particle transport and end-plug stability. These questions are discussed at length in the report and suggestions for future work are given.

  19. Carbon Pricing: Design, Experiences and Issues

    DEFF Research Database (Denmark)

    Carbon Pricing reflects upon and further develops the ongoing and worthwhile global debate into how to design carbon pricing, and how to utilize the financial proceeds in the best possible way for society. The world has recently witnessed a significant downward adjustment in fossil fuel prices...... the consequential outcomes of different taxation compositions as regulatory instruments. Expert contributors assess a variety of national experiences to provide an empirical insight into the use of carbon taxes, emissions trading, energy taxes and excise taxes. The overarching discussion concludes that successful...

  20. Design of Experiments for Food Engineering

    OpenAIRE

    Pedersen, Søren Juhl; Frosch, Stina; Kulahci, Murat; Geoffrey Vining, G.

    2015-01-01

    This work looks at the application of Design of Experiments (DoE) to Food Engineering (FE) problems in relation to quality. The field of Quality Engineering (QE) is a natural partnering field for FE due to the extensive developments that QE has had in using DoE for quality improvement especially in manufacturing industries. In the thesis the concepts concerning food quality is addressed and in addition how QE proposes to define quality. There is seen a merger in how QE’s definition of quality...

  1. Preliminary Design Options for Meteor Burst Communications Systems Buoy Relays

    Science.gov (United States)

    1986-12-01

    the lithium - thionyl chloride cell exhibit specific energies of the order of 500 watt hours per kilogram, more than 50 percent higher than previous...Supply Buoy Design Type 90 Day Storage Weight Type Energy Type Size (lb) Remote Lithium 2.2 kWh Deployable 8" x 8" x 4’ 200 Battery Pendulous Master...however, that there are various typcs of lithium batteries presently being developed that have energy densities equal to’fuel cell power systems. It is

  2. Preliminary structural evaluation and design of the HL-20

    Science.gov (United States)

    Bush, Lance B.; Wahls, Deborah M.; Robinson, James C.

    1993-02-01

    Several concepts have been proposed to meet the requirements of a Personnel Launch System. A lifting body concept, the HL-20, was designed at NASA Langley Research Center. A structural analysis of a proposed HL-20 configuration with a cylindrical pressurized crew cabin is presented in this paper. Loads for the vehicle are assembled from mission loading conditions such as abort, on-orbit pressurization, blast overpressure, aerodynamic maneuver, and touchdown. The critical loading conditions are identified and resultant loads mapped onto the structure in order to review the effects of the mission loading conditions. The HL-20 structural concept is sized for the mission loads and the resulting structural weights are calculated.

  3. Design of Pulsed Strong Magnetic Fields Generator and Preliminary Application

    Institute of Scientific and Technical Information of China (English)

    WEN Jun; QU Xue-min; WANG Xi-gang; LONG Kai-ping

    2015-01-01

    Objective: This paper aims to designing a pulsed strong magnetic fields generator. Methods: A large value capacitor was used to store electric energy, coil was used for producing magnetic fields, main control, circuit control charge, sampling, discharge, etc. Results: The generator provided a pulsed magnetic field with the ampli-tude of intensity from 0.1-2 T and variable time interval of pulse from 4 s-1 min. It was not only to be operated easily but also performed reliably. Conclusion:The generator will be applied in special clinical diagnosis, therapy and other fields.

  4. Building Case—Based Preliminary Design Systems:A Hopfield Network Approach

    Institute of Scientific and Technical Information of China (English)

    吴维; 盛之进; 等

    1994-01-01

    This paper addresses the issue of building a case-based preliminary desing system by using Hopfield networks.One limitation of Hopfield networks is that it cannot be trained,i.e.the weights between two neurons must be set in advance.A pattern stored in Hopfield networks cannot be recalled if the pattern is not a local minimum.Two concepts are proposed to deal with this problem.They are the multiple training encoding method and the puppet encoding method.The multiple training encoding method,which guarantees to recall a single stored pattern under appropriate initial conditions of data,is theoreticall analyzed,and the minimal number of times for using a pattern for training to guarantee recalling of the pattern among a set of patterns is derived.The puppet encoding method is proved to be able to guarantee recalling of all stored patterns if attaching puppet data to the stored patterns is available. An integrated software PDS (Preliminary Design System),which is developed from two aspects,is described.One is from a case-based expert system--CPDS(Case-based Preliminary Design System),which is based on the algorithm of the Hopfield and developed for uncertain problems in PDS;the other is RPDS (Rule-based Preliminary Design System),which attacks logic or deduced problems in PDS.Based on the results of CPDS,RPDS can search for feasible solution in design model.CPDS is demonstrated to be useful in the domains of preliminary designs of cable-stayed bridges in this paper.

  5. Preliminary design of the Carrisa Plains solar central receiver power plant. Volume II. Plant specifications

    Energy Technology Data Exchange (ETDEWEB)

    Price, R. E.

    1983-12-31

    The specifications and design criteria for all plant systems and subsystems used in developing the preliminary design of Carrisa Plains 30-MWe Solar Plant are contained in this volume. The specifications have been organized according to plant systems and levels. The levels are arranged in tiers. Starting at the top tier and proceeding down, the specification levels are the plant, system, subsystem, components, and fabrication. A tab number, listed in the index, has been assigned each document to facilitate document location.

  6. Kemper County IGCC (tm) Project Preliminary Public Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Matt; Rush, Randall; Madden, Diane; Pinkston, Tim; Lunsford, Landon

    2012-07-01

    The Kemper County IGCC Project is an advanced coal technology project that is being developed by Mississippi Power Company (MPC). The project is a lignite-fueled 2-on-1 Integrated Gasification Combined-Cycle (IGCC) facility incorporating the air-blown Transport Integrated Gasification (TRIG™) technology jointly developed by Southern Company; Kellogg, Brown, and Root (KBR); and the United States Department of Energy (DOE) at the Power Systems Development Facility (PSDF) in Wilsonville, Alabama. The estimated nameplate capacity of the plant will be 830 MW with a peak net output capability of 582 MW. As a result of advanced emissions control equipment, the facility will produce marketable byproducts of ammonia, sulfuric acid, and carbon dioxide. 65 percent of the carbon dioxide (CO{sub 2}) will be captured and used for enhanced oil recovery (EOR), making the Kemper County facility’s carbon emissions comparable to those of a natural-gas-fired combined cycle power plant. The commercial operation date (COD) of the Kemper County IGCC plant will be May 2014. This report describes the basic design and function of the plant as determined at the end of the Front End Engineering Design (FEED) phase of the project.

  7. Integrated Box Interrogation System (IBIS) Preliminary Design Study

    Energy Technology Data Exchange (ETDEWEB)

    DR. Stephen Croft; Mr. David Martancik; Dr. Brian Young; Dr. Patrick MJ Chard; Dr. Robert J Estop; Sheila Melton; Gaetano J. Arnone

    2003-01-13

    Canberra Industries has won the tendered solicitation, INEEL/EST-99-00121 for boxed waste Nondestructive Assay Development and Demonstration. Canberra will provide the Integrated Box Interrogation System (IBIS) which is a suite of assay instrumentation and a data reduction system that addresses the measurement needs for Boxed Wastes identified in the solicitation and facilitates the associated experimental program and demonstration of system capability. The IBIS system will consist of the next generation CWAM system, i.e. CWAM II, which is a Scanning Passive/Active Neutron interrogation system which we will call a Box Segmented Neutron Scanner (BSNS), combined with a physically separate Box Segmented Gamma-ray Scanning (BSGS) system. These systems are based on existing hardware designs but will be tailored to the large sample size and enhanced to allow the program to evaluate the following measurement criteria:Characterization and correction for matrix heterogeneity Characterization of non-uniform radio-nuclide and isotopic compositions Assay of high density matrices (both high-Z and high moderator contents)Correction for radioactive material physical form - such as self shielding or multiplication effects due to large accumulations of radioactive materials.Calibration with a minimal set of reference standards and representative matrices.THis document summarizes the conceptual design parameters of the IBIS and indicates areas key to the success of the project where development is to be centered. The work presented here is a collaborative effort between scientific staff within Canberra and within the NIS-6 group at LANL.

  8. The lunar gravity mission MAGIA: preliminary design and performances

    Science.gov (United States)

    Fermi, Marco; Gregnanin, Marco; Mazzolena, Marco; Chersich, Massimiliano; Reguzzoni, Mirko; Sansò, Fernando

    2011-10-01

    The importance of an accurate model of the Moon gravity field has been assessed for future navigation missions orbiting and/or landing on the Moon, in order to use our natural satellite as an intermediate base for next solar system observations and exploration as well as for lunar resources mapping and exploitation. One of the main scientific goals of MAGIA mission, whose Phase A study has been recently funded by the Italian Space Agency (ASI), is the mapping of lunar gravitational anomalies, and in particular those on the hidden side of the Moon, with an accuracy of 1 mGal RMS at lunar surface in the global solution of the gravitational field up to degree and order 80. MAGIA gravimetric experiment is performed into two phases: the first one, along which the main satellite shall perform remote sensing of the Moon surface, foresees the use of Precise Orbit Determination (POD) data available from ground tracking of the main satellite for the determination of the long wavelength components of gravitational field. Improvement in the accuracy of POD results are expected by the use of ISA, the Italian accelerometer on board the main satellite. Additional gravitational data from recent missions, like Kaguya/Selene, could be used in order to enhance the accuracy of such results. In the second phase the medium/short wavelength components of gravitational field shall be obtained through a low-to-low (GRACE-like) Satellite-to-Satellite Tracking (SST) experiment. POD data shall be acquired during the whole mission duration, while the SST data shall be available after the remote sensing phase, when the sub-satellite shall be released from the main one and both satellites shall be left in a free-fall dynamics in the gravity field of the Moon. SST range-rate data between the two satellites shall be measured through an inter-satellite link with accuracy compliant with current state of art space qualified technology. SST processing and gravitational anomalies retrieval shall

  9. Design and preliminary validation of a tool for the simulation of train braking performance

    Institute of Scientific and Technical Information of China (English)

    Luca Pugi; Monica Malvezzi; Susanna Papini; Gregorio Vettori

    2013-01-01

    Train braking performance is important for the safety and reliability of railway systems. The availability of a tool that allows evaluating such performance on the basis of the main train features can be useful for train system designers to choose proper dimensions for and optimize train’s subsystems. This paper presents a modular tool for the prediction of train braking performance, with a par-ticular attention to the accurate prediction of stopping distances. The tool takes into account different loading and operating conditions, in order to verify the safety require-ments prescribed by European technical specifications for interoperability of high-speed trains and the corresponding EN regulations. The numerical results given by the tool were verified and validated by comparison with experi-mental data, considering as benchmark case an Ansaldo EMU V250 train-a European high-speed train-currently developed for Belgium and Netherlands high-speed lines, on which technical information and experimental data directly recorded during the preliminary tests were avail-able. An accurate identification of the influence of the braking pad friction factor on braking performances allowed obtaining reliable results.

  10. Designing Technology for Active Spectator Experiences at Sporting Events

    DEFF Research Database (Denmark)

    Veerasawmy, Rune; Ludvigsen, Martin

    2010-01-01

    behaviour in the context. The work presented also argues for a need to overcome the inclination to designing technological systems that imitate or compete with the experience of watching the television broadcast of the game. Experiments such as the presented BannerBattle are cornerstones in our exploratory......This paper explores the active spectator experience at sporting events, by presenting and reflecting upon a design experiment carried out at a number of football1 events. The initial hypothesis of the design process, leading to the design experiment has been that the spectator experience...... research-through-design approach to designing technologies for social experiences....

  11. Preliminary Design Study for a National Digital Seismograph Network

    Science.gov (United States)

    Peterson, Jon; Hutt, Charles R.

    1981-01-01

    Introduction Recently, the National Research Council published a report by the Panel on National, Regional, and Local Seismograph Networks of the Committee on Seismology in which the principal recommendation was for the establishment of a national digital seismograph network (NDSN). The Panel Report (Bolt, 1980) addresses both the need and the scientific requirements for the new national network. The purpose of this study has been to translate the scientific requirements into an instrumentation concept for the NSDS. There are literally hundreds, perhaps thousands, of seismographs in operation within the United States. Each serves an important purpose, but most have limited objectives in time, in region, or in the types of data that are being recorded. The concept of a national network, funded and operated by the Federal Government, is based on broader objectives that include continuity of time, uniform coverage, standardization of data format and instruments, and widespread use of the data for a variety of research purposes. A national digital seismograph network will be an important data resource for many years to come; hence, its design is likely to be of interest to most seismologists. Seismologists have traditionally been involved in the development and field operation of seismic systems and thus have been familiar with both the potential value and the limitations of the data. However, in recent years of increasing technological sophistication, the development of data sstems has fallen more to system engineers, and this trend is likely to continue. One danger in this is that the engineers may misinterpret scientific objectives or subordinate them to purely technological considerations. Another risk is that the data users may misuse or misinterpret the data because they are not aware of the limitations of the data system. Perhaps the most important purpose of a design study such as this is to stimulate a dialogue between system engineers and potential data users

  12. Integrated Box Interrogation System (IBIS) Preliminary Design Study

    CERN Document Server

    Croft, S; Chard-Mj, P; Estop, J R; Martancik, D; Sheila-Melton; Young, B

    2003-01-01

    Canberra Industries has won the tendered solicitation, INEEL/EST-99-00121 for boxed waste Nondestructive Assay Development and Demonstration. Canberra will provide the Integrated Box Interrogation System (IBIS) which is a suite of assay instrumentation and a data reduction system that addresses the measurement needs for Boxed Wastes identified in the solicitation and facilitates the associated experimental program and demonstration of system capability. The IBIS system will consist of the next generation CWAM system, i.e. CWAM II, which is a Scanning Passive/Active Neutron interrogation system which we will call a Box Segmented Neutron Scanner (BSNS), combined with a physically separate Box Segmented Gamma-ray Scanning (BSGS) system. These systems are based on existing hardware designs but will be tailored to the large sample size and enhanced to allow the program to evaluate the following measurement criteria:Characterization and correction for matrix heterogeneity Characterization of non-uniform radio-nucli...

  13. Expanded microchannel heat exchanger: design, fabrication and preliminary experimental test

    CERN Document Server

    Denkenberger, David C; Pearce, Joshua M; Zhai, John; 10.1177/0957650912442781

    2012-01-01

    This paper first reviews non-traditional heat exchanger geometry, laser welding, practical issues with microchannel heat exchangers, and high effectiveness heat exchangers. Existing microchannel heat exchangers have low material costs, but high manufacturing costs. This paper presents a new expanded microchannel heat exchanger design and accompanying continuous manufacturing technique for potential low-cost production. Polymer heat exchangers have the potential for high effectiveness. The paper discusses one possible joining method - a new type of laser welding named "forward conduction welding," used to fabricate the prototype. The expanded heat exchanger has the potential to have counter-flow, cross-flow, or parallel-flow configurations, be used for all types of fluids, and be made of polymers, metals, or polymer-ceramic precursors. The cost and ineffectiveness reduction may be an order of magnitude or more, saving a large fraction of primary energy. The measured effectiveness of the prototype with 28 micro...

  14. The Large Synoptic Survey Telescope preliminary design overview

    Science.gov (United States)

    Krabbendam, V. L.; Sweeney, D.

    2010-07-01

    The Large Synoptic Survey Telescope (LSST) Project is a public-private partnership that is well into the design and development of the complete observatory system to conduct a wide fast deep survey and to process and serve the data. The telescope has a 3-mirror wide field optical system with an 8.4 meter primary, 3.4 meter secondary, and 5 meter tertiary mirror. The reflective optics feed three refractive elements and a 64 cm 3.2 gigapixel camera. The LSST data management system will reduce, transport, alert and archive the roughly 15 terabytes of data produced nightly, and will serve the raw and catalog data accumulating at an average of 7 petabytes per year to the community without any proprietary period. The project has completed several data challenges designed to prototype and test the data management system to significant pre-construction levels. The project continues to attract institutional partners and has acquired non-federal funding sufficient to construct the primary mirror, already in progress at the University of Arizona, build the secondary mirror substrate, completed by Corning, and fund detector prototype efforts, several that have been tested on the sky. A focus of the project is systems engineering, risk reduction through prototyping and major efforts in image simulation and operation simulations. The project has submitted a proposal for construction to the National Science Foundation Major Research Equipment and Facilities Construction (MREFC) program and has prepared project advocacy papers for the National Research Council's Astronomy 2010 Decadal Survey. The project is preparing for a 2012 construction funding authorization.

  15. Everyday life; Lived Experiences and Designed Learning

    DEFF Research Database (Denmark)

    Vestbo, Michelle; Helms, Niels Henrik; Dræbel, Tania Aase

    2016-01-01

    Everyday life; Lived Experiences and Designed Learning: Students knowledge cultures and epistemic trajectories in a range of professional bachelor educations Helms, N.H., Vestbo, M., Steenfeldt, V.O., Dræbel, T.A., Hansen, T.A.E., Storm, H., and Schmidt, L.S.K. (University College Zealand) In thi...... contributes to knowledge about how students translate and transform knowledge in various ways and how they establish professional competencies and identities and about the potential coherence between portfolio pedagogies and other educational activities.......Everyday life; Lived Experiences and Designed Learning: Students knowledge cultures and epistemic trajectories in a range of professional bachelor educations Helms, N.H., Vestbo, M., Steenfeldt, V.O., Dræbel, T.A., Hansen, T.A.E., Storm, H., and Schmidt, L.S.K. (University College Zealand......) In this panel the use of different methodological approaches to answer questions about students’ knowledge cultures and epistemic trajectories is discussed. The context is qualitative empirical educational studies in a range of professional bachelor educations; Nursing, Social Education and Nutrition and Health...

  16. The application of APTEA experiment design to the experiment for determining information density of large scale display panel

    Energy Technology Data Exchange (ETDEWEB)

    Sim, Bong Sik; Oh, In Suk; Cha, Kyung Ho; Lee, Hyun Cheol [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1995-06-01

    APTEA experiment design was developed for the purpose of enhancing the availability of integrated test facility in 1994, and is composed of 5 phases including 28 contents. We applied APTEA experiment design to a preliminary human factors experiment for the determination of information density on a large scale display panel in order to confirm the usability of APTEA before utilizing it with integrated test facility. As results, we verified the easiness on the use of APTEA experiment design and identified points to be considered as follows. - Each phase and content doesn`t demand the same duration and level of work. Therefore it is unnecessary for experimenter to give same weight to all the phases and contents. - Filling up the phases and contents of ATPEA require various knowledge such as programming, human factors principles, experiment design. So a multidisciplinary team is desired in using APTEA experiment design. - It will be difficult to clearly discern the differences among contents in some experiments. In this case, the integration of several contents is desirable. 5 tabs., 2 figs., 5 refs. (Author) .new.

  17. Preliminary Study for Designing a Novel Vein-Visualizing Device

    Directory of Open Access Journals (Sweden)

    Donghoon Kim

    2017-02-01

    Full Text Available Venipuncture is an important health diagnosis process. Although venipuncture is one of the most commonly performed procedures in medical environments, locating the veins of infants, obese, anemic, or colored patients is still an arduous task even for skilled practitioners. To solve this problem, several devices using infrared light have recently become commercially available. However, such devices for venipuncture share a common drawback, especially when visualizing deep veins or veins of a thick part of the body like the cubital fossa. This paper proposes a new vein-visualizing device applying a new penetration method using near-infrared (NIR light. The light module is attached directly on to the declared area of the skin. Then, NIR beam is rayed from two sides of the light module to the vein with a specific angle. This gives a penetration effect. In addition, through an image processing procedure, the vein structure is enhanced to show it more accurately. Through a phantom study, the most effective penetration angle of the NIR module is decided. Additionally, the feasibility of the device is verified through experiments in vivo. The prototype allows us to visualize the vein patterns of thicker body parts, such as arms.

  18. Preliminary Study for Designing a Novel Vein-Visualizing Device.

    Science.gov (United States)

    Kim, Donghoon; Kim, Yujin; Yoon, Siyeop; Lee, Deukhee

    2017-02-07

    Venipuncture is an important health diagnosis process. Although venipuncture is one of the most commonly performed procedures in medical environments, locating the veins of infants, obese, anemic, or colored patients is still an arduous task even for skilled practitioners. To solve this problem, several devices using infrared light have recently become commercially available. However, such devices for venipuncture share a common drawback, especially when visualizing deep veins or veins of a thick part of the body like the cubital fossa. This paper proposes a new vein-visualizing device applying a new penetration method using near-infrared (NIR) light. The light module is attached directly on to the declared area of the skin. Then, NIR beam is rayed from two sides of the light module to the vein with a specific angle. This gives a penetration effect. In addition, through an image processing procedure, the vein structure is enhanced to show it more accurately. Through a phantom study, the most effective penetration angle of the NIR module is decided. Additionally, the feasibility of the device is verified through experiments in vivo. The prototype allows us to visualize the vein patterns of thicker body parts, such as arms.

  19. Preliminary Study for Designing a Novel Vein-Visualizing Device

    Science.gov (United States)

    Kim, Donghoon; Kim, Yujin; Yoon, Siyeop; Lee, Deukhee

    2017-01-01

    Venipuncture is an important health diagnosis process. Although venipuncture is one of the most commonly performed procedures in medical environments, locating the veins of infants, obese, anemic, or colored patients is still an arduous task even for skilled practitioners. To solve this problem, several devices using infrared light have recently become commercially available. However, such devices for venipuncture share a common drawback, especially when visualizing deep veins or veins of a thick part of the body like the cubital fossa. This paper proposes a new vein-visualizing device applying a new penetration method using near-infrared (NIR) light. The light module is attached directly on to the declared area of the skin. Then, NIR beam is rayed from two sides of the light module to the vein with a specific angle. This gives a penetration effect. In addition, through an image processing procedure, the vein structure is enhanced to show it more accurately. Through a phantom study, the most effective penetration angle of the NIR module is decided. Additionally, the feasibility of the device is verified through experiments in vivo. The prototype allows us to visualize the vein patterns of thicker body parts, such as arms. PMID:28178227

  20. Farm Fuel Alcohol Project: preliminary report on facility design

    Energy Technology Data Exchange (ETDEWEB)

    Pile, R S; Badger, P C; Roetheli, J C; Waddell, Jr, E L

    1979-09-01

    This report describes the design of a farm-based ethanol production system to be built by TVA at Muscle Shoals, Alabama. This facility will include cooking, fermentation, and distillation equipment to allow production of 8000 to 12,000 gallons of fuel ethanol during a three to four month period each year. Output will be about 10 gallons of 190-proof ethanol per hour. Present components are sized to allow 12 to 14 hour daily operation as a semi-continuous batch system. Intent of the project is to document equipment and energy requirements, ethanol yields, and feasibility of small farm-based ethanol plants for farm fuel self-sufficiency. Cooking and fermentation will be batch-type operations, and packed distillation columns will be used for separating ethanol from the fermented beer. Energy recovery and waste heat use are integrated when feasible. The fermented beer will be fed directly to the distillation columns without separation of solids. Although this is an area of concern, an economical method of separation could not be identified.

  1. Large utility boilers: experience and design trends

    Energy Technology Data Exchange (ETDEWEB)

    Davis, C.M.; Haller, K.H.; Wiener, M.

    1976-01-01

    The 1960s were characterized by heavy emphasis on the supercritical cycle and a rapid escalation of utility boiler size. Since the units now in operation were designed, several important changes have caused drastic turns in boiler development. The 2400-lb/in./sup 2/ single-reheat, 1000/sup 0/F/1000/sup 0/F cycle regained importance. The present trend is toward natural circulation because it is the simplest, the most efficient, and the most reliable method of furnace wall cooling. With the emphasis on energy self-sufficiency, coal became the dominant boiler fuel. A great deal of uncertainty exists regarding future development of load growth, fossil to nuclear split, environmental regulations, availability of fuel and availability of capital for new construction. These factors are shaping the trends that we see: the utilization of all available coal sources, including very-low-grade coals, the design of units for a wide range of coals, the design for greater operating flexibility, and placement of heavy emphasis on reliability. Based on the good experience with recent large B and W coal-fired boilers, the even greater conservatism applied to new large, coal-fired boilers should provide the capability for continued good performance and high availability.

  2. Neutronic analyses of the preliminary design of a DCLL blanket for the EUROfusion DEMO power plant

    Energy Technology Data Exchange (ETDEWEB)

    Palermo, Iole, E-mail: iole.palermo@ciemat.es; Fernández, Iván; Rapisarda, David; Ibarra, Angel

    2016-11-01

    Highlights: • We perform neutronic calculations for the preliminary DCLL Blanket design. • We study the tritium breeding capability of the reactor. • We determine the nuclear heating in the main components. • We verify if the shielding of the TF coil is maintained. - Abstract: In the frame of the newly established EUROfusion WPBB Project for the period 2014–2018, four breeding blanket options are being investigated to be used in the fusion power demonstration plant DEMO. CIEMAT is leading the development of the conceptual design of the Dual Coolant Lithium Lead, DCLL, breeding blanket. The primary role of the blanket is of energy extraction, tritium production, and radiation shielding. With this aim the DCLL uses LiPb as primary coolant, tritium breeder and neutron multiplier and Eurofer as structural material. Focusing on the achievement of the fundamental neutronic responses a preliminary blanket model has been designed. Thus detailed 3D neutronic models of the whole blanket modules have been generated, arranged in a specific DCLL segmentation and integrated in the generic DEMO model. The initial design has been studied to demonstrate its viability. Thus, the neutronic behaviour of the blanket and of the shield systems in terms of tritium breeding capabilities, power generation and shielding efficiency has been assessed in this paper. The results demonstrate that the primary nuclear performances are already satisfactory at this preliminary stage of the design, having obtained the tritium self-sufficiency and an adequate shielding.

  3. Ocean Thermal Energy Conversion power system development. Phase I: preliminary design. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-04

    Westinghouse has completed the Preliminary Desigh Phase for the Power System Development of the Ocean Thermal Energy Conversion (OTEC) Demonstration Plant project. This study included the development of a preliminary design for a Modular Application scaled power system (10MWe) and Heat Exchanger Test Articles, both based on the concept developed in the Conceptual Design Phase. The results of this study were used to improve the baseline design of the 50MWe module for the Commercial Size Power System, which was recommended for the demonstration plant by the conceptual design study. The 50MWe module was selected since it has the lowest cost, and since its size convincingly demonstrates that future economically viable commercial plants, having reliable operation with credible anticipated costs, are possible. Additional optimization studies on the size of the power system plus hull continue to identify 50MWe as the preferred minimum cost configuration. This study was limited to a closed cycle ammonia power system module, using a seawater temperature difference of 40/sup 0/F, and a surface platform/ship reference hull. This volume presents the preliminary design configuration and system optimization. (WHK)

  4. Ocean thermal energy conversion (OTEC) power system development. Preliminary design report, Appendices, Part 1 (Final)

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-04

    The objective of this project is the development of a preliminary design for a full-sized, closed cycle, ammonia power system module for the 100 MWe OTEC demonstration plant. In turn, this demonstration plant is to demonstrate, by 1984, the operation and performance of an Ocean Thermal Power Plant having sufficiently advanced heat exchanger design to project economic viability for commercial utilization in the late 1980's and beyond. Included in this power system development are the preliminary designs for a proof-of-concept pilot plant and test article heat exchangers which are scaled in such a manner as to support a logically sequential, relatively low-cost development of the full-scale power system module. The conceptual designs are presented for the demonstration plant power module, the proof-of-concept pilot plant, and for a pair of test article heat exchangers. Costs associated with the design, development, fabrication, checkout, delivery, installation, and operation are included. The accompanying design and producibilty studies on the full-scale power system module project the performance/economics for the commercial plant. This section of the report contains appendices on the developed computer models, water system dynamic studies, miscellaneous performance analysis, materials and processes, detailed equipment lists, turbine design studies, tube cleaner design, ammonia leak detection, and heat exchanger design supporting data. (WHK)

  5. Characterization of the designer benzodiazepine diclazepam and preliminary data on its metabolism and pharmacokinetics.

    Science.gov (United States)

    Moosmann, Bjoern; Bisel, Philippe; Auwärter, Volker

    2014-01-01

    Designer benzodiazepines, first offered in online shops selling 'research chemicals' in 2012, provide an attractive alternative to prescription-only benzodiazepines as they are readily available over the Internet at a low price. However, as data regarding pharmacokinetic parameters, metabolism, and detectability in biological fluids are limited, they present a challenge for forensic laboratories. Most recently, diclazepam (other names: 2-chlorodiazepam, Ro 5-3448 or 7-chloro-5-(2-chlorophenyl)-1-methyl-1,3-dihydro-2H-1,4-benzodiazepin-2-one) emerged as a new compound in this class of drugs. In this paper, this new designer benzodiazepine was characterized utilizing nuclear magnetic resonance (NMR), gas chromatography-mass spectrometry (GC-MS) as well as liquid chromatography tandem mass spectrometry (LC-MS/MS) techniques. Furthermore, a self-experiment was performed to gain preliminary data on pharmacokinetic properties and to identify the main metabolites. For this purpose, one tablet of diclazepam (declared amount: 1 mg) was ingested by one of the authors, and serum as well as urine samples were collected for 14 and 21 days, respectively. Based on this study, diclazepam has an approximate elimination half-life of 42 h and is metabolized into the pharmacologically active benzodiazepines delorazepam, lorazepam, and lormetazepam which can be detected in urine for 6, 19, and 11 days, respectively, when applying the presented LC-MS/MS method. In serum, the consumption could be proven between 99 h post-intake targeting the parent compound and up to 10 days targeting the metabolite delorazepam. As immunochemical assays are applied for screening purposes quite often, detectability using this technique was assessed, especially since detection of low-dosed benzodiazepines can be sometimes problematic. However, only one of the utilized immunochemical assays was capable of detecting the intake of one tablet diclazepam, and the positive results were restricted to a few urine

  6. Judgement post-stratification for designed experiments.

    Science.gov (United States)

    Du, Juan; MacEachern, Steven N

    2008-06-01

    In many scientific studies, information that is not easily translated into covariates is ignored in the analysis. However, this type of information may significantly improve inference. In this research, we apply the idea of judgment post-stratification to utilize such information. Specifically, we consider experiments that are conducted under a completely randomized design. Sets of experimental units are formed, and the units in a set are ranked. Estimation is performed conditional on the sets and ranks. We propose a new estimator for a treatment contrast. We improve the new estimator by Rao-Blackwellization. Asymptotic distribution theory and corresponding inferential procedures for both estimators are developed. Simulation studies quantify the superiority of the new estimators and show their desirable properties for small and moderate sample sizes. The impact of the new techniques is illustrated with data from a clinical trial.

  7. Design of Experiments for Food Engineering

    DEFF Research Database (Denmark)

    Pedersen, Søren Juhl; Geoffrey Vining, G.

    in manufacturing industries. In the thesis the concepts concerning food quality is addressed and in addition how QE proposes to define quality. There is seen a merger in how QE’s definition of quality has been translated for food. At the same time within FE a divergence has been proposed in the literature...... emphasizing mechanistic modelling over empirical methods. This thesis proposes that this divergence is based on a misunderstanding of what empirical methods entail. The misunderstanding could stem from the issue that the majority of the literature trying to address these issues has focused on analysis...... procedure almost to the point of excluding the experimental principles and procedures. This thesis has tried to address this as far as possible. The focus has been on supplying practical interpretations of randomization and what blocking entails when designing experiments. These practical interpretations...

  8. Design and operation experience of TRACY

    Energy Technology Data Exchange (ETDEWEB)

    Takeshita, Isao; Ohno, Akio; Sakuraba, Koichi; Ogawa, Kazuhiko; Morita, Toshio; Aizawa, Eiju; Sugawara, Susumu [Department of NUCEF Project, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan)

    1999-08-01

    To realize the dynamic behaviors at a criticality accident is an essential issue for not only rational design of fissile material handing facilities but also safety management of the facilities. The Transient Experiment Critical Facility (TRACY) had been constructed at the Nuclear Fuel Cycle Safety Engineering Research Facility (NUCEF) in JAERI. The purpose of TRACY is to obtain experimental data necessary to evaluate potential hazard of a criticality accident postulated in safety assessments of a reprocessing plant. TRACY's first transient operation using low enriched (10%) uranium nitrate solution fuel went on July 30 1996 and 118 operations including 51 transient operations are recorded since the first critical achievement. TRACY carries out intensive experimental researches on nuclear-thermal-hydraulic dynamic behavior and on investigation of migration amount of radioactive nuclei in solution fuel to gas phase. (author)

  9. MICE -- Absorber and focus coil safety working group design document: Preliminary design and assessments

    Energy Technology Data Exchange (ETDEWEB)

    Barr, Giles; Baynham, Elwyn; Black, Edgar; Bradshaw, Tom; Cummings, Mary Anne; Green, Michael A.; Ishimoto, Shigeru; Ivanyushenkov, Yury; Lau, Wing; Zisman, Michael

    2003-12-04

    A Neutrino Factory based on a muon storage ring is the ultimate tool for studies of neutrino oscillations, including possibly the discovery of leptonic CP violation. it is also the first step toward a muon collider. To develop a stored-muon-beam facility to serve as a Neutrino Factory, it is necessary to ''cool'' a muon beam (decrease its phase-space volume). The short lifetime of the muon, 2.2 {micro}s at rest, eliminates all currently demonstrated cooling techniques and requires that a new, heretofore untried, technique--ionization cooling--be employed. Although ionization cooling of muons has never been demonstrated in practice, it has been shown by end-to-end simulation and design studies to be an important factor both for the performance and for the cost of a Neutrino Factory. This motivates an international program of R and D, including an experimental demonstration at Rutherford Appleton Laboratory (RAL). The aims of the international Muon Ionization Cooling Experiment are: (1) to show that it is possible to design, engineer and build a section of cooling channel capable of giving the desired performance for a Neutrino Factory; and (2) to place it in a muon beam and measure its performance in various modes of operation and beam conditions, thereby investigating the limits and practicality of cooling. The MICE collaboration has designed an experiment in which a section of an ionization cooling channel is exposed to a muon beam. This cooling channel assembles liquid-hydrogen absorbers providing energy loss and high-gradient radio frequency (RF) cavities to re-accelerate the particles, all tightly contained in a magnetic channel. It reduces the beam transverse emittance by > 10% for muon momenta between 140 and 240 MeV/c. The layout of the experiment is shown. They utilize one complete magnetic cell of the cooling channel, comprising three absorber-focus-coil (AFC) modules and two RF-coupling-coil (RFCC) modules. Spectrometers placed before

  10. Tourism Spaces: The New Experience Design

    Directory of Open Access Journals (Sweden)

    Sara Cipolletti

    2014-06-01

    Full Text Available The aim of this article is to offer a theoretical contribution to the organisation, design and significance of tourism spaces, at a time when tourist practices are experiencing both change and intensification. From an architectural perspective, the study seeks to understand the evolutionary link between holiday practices and spaces, interpreting tourism as a context of creative relations between people, aspects, things and the places in which practices take place.Based on this interpretation, the paper defines architectural and urban categories of tourism, briefly comparing various literature on tourist organisations. In the second part, through the examination of recent examples of tourist experiences, planning actions and their ability to generate new tourism landscapes are evaluated. For both places and tourist experiences, that which emerges and the fields of application involved constitute guidelines and development tools for a form of tourism design that is more knowledgeable about the encounter between tourists and residents, and more reliable given that it is founded on the distinctive features of territories. The study demonstrates that tourism spaces, if intended as contexts of creative relations between people, aspects, things and places in which practices take place, may now develop a certain potential that once again calls into question a series of much debated opposites, tourists - residents, free time - work time, holiday space - day-to-day space, attractive resources and their transformation into elements of tourism, which had otherwise previously been consolidated by the tourist phenomenon. In the end, tourism proves itself to be an imaginative impulse, which is capable of reinventing the qualities of places and successfully orientating urban events.

  11. Preliminary Design Report for the Yakima/Klickitat Production Project; Executive Summary.

    Energy Technology Data Exchange (ETDEWEB)

    US Bonneville Power Administration.

    1990-03-01

    A master plan for the Yakima/Klickitat Production Project (YKPP) was developed by the Northwest Power Planning Council (Council) on October 15, 1987, as a reasonable basis upon which the Bonneville Power Administration (BPA) could proceed to fund predesign work on the project. The Council approved the predesign work on the condition that eight preliminary tasks were completed. These tasks are: Agreement on a refined statement of project goals. Completion of a technical analysis of water supplies. Completion of an experimental design plan. Development of a harvest management plan. Assessment of potential genetic risks. Project coordination with all other affected parties. Submission of a preliminary design report to the Council. Develop a project management structure. The preliminary design report summarizes the work completed on these tasks. It provides a description of the preliminary design, engineering, and construction phases of project development, and gives an estimate of project costs. Also included is a description of other studies that were conducted to support YKPP planning. The results of studies conducted during the last 30 months indicate that hatchery facilities can be built in the Yakima and Klickitat subbasins to provide harvest benefits and to supplement natural production. Planning for the Yakima subbasin is at a more advanced stage of development than for the Klickitat subbasin because of greater availability of basic resource information. The information needed to proceed with final design and construction for the Klickitat subbasin will be available by 1992, as ongoing predesign work continues. This schedule is consistent with the anticipated phased completion of the YKPP by 1997.

  12. Preliminary Design and Analysis of the ARES Atmospheric Flight Vehicle Thermal Control System

    Science.gov (United States)

    Gasbarre, J. F.; Dillman, R. A.

    2003-01-01

    The Aerial Regional-scale Environmental Survey (ARES) is a proposed 2007 Mars Scout Mission that will be the first mission to deploy an atmospheric flight vehicle (AFV) on another planet. This paper will describe the preliminary design and analysis of the AFV thermal control system for its flight through the Martian atmosphere and also present other analyses broadening the scope of that design to include other phases of the ARES mission. Initial analyses are discussed and results of trade studies are presented which detail the design process for AFV thermal control. Finally, results of the most recent AFV thermal analysis are shown and the plans for future work are discussed.

  13. Ocean thermal energy conversion (OTEC). Power system development. Preliminary design report, final

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-04

    The preliminary design of the 10 MWe OTEC power module and the 200 kWe test articles is given in detail. System operation and performance; power system cost estimates; 10 MWe heat exchangers; 200 kWe heat exchanger articles; biofouling control;ammonia leak detection, and leak repair; rotating machinery; support subsystem; instrumentation and control; electrical subsystem; installation approach; net energy and resource analysis; and operability, maintainability, and safety are discussed. The conceptual design of the 40 MWe electrical power system includes four or five 10 MWe modules as designed for the 10 MWe pilot plant. (WHK)

  14. Interim Service ISDN Satellite (ISIS) hardware experiment design for advanced ISDN satellite design and experiments

    Science.gov (United States)

    Pepin, Gerard R.

    1992-01-01

    The Interim Service Integrated Services Digital Network (ISDN) Satellite (ISIS) Hardware Experiment Design for Advanced Satellite Designs describes the design of the ISDN Satellite Terminal Adapter (ISTA) capable of translating ISDN protocol traffic into time division multiple access (TDMA) signals for use by a communications satellite. The ISTA connects the Type 1 Network Termination (NT1) via the U-interface on the line termination side of the CPE to the V.35 interface for satellite uplink. The same ISTA converts in the opposite direction the V.35 to U-interface data with a simple switch setting.

  15. Design Point for a Spheromak Compression Experiment

    Science.gov (United States)

    Woodruff, Simon; Romero-Talamas, Carlos A.; O'Bryan, John; Stuber, James; Darpa Spheromak Team

    2015-11-01

    Two principal issues for the spheromak concept remain to be addressed experimentally: formation efficiency and confinement scaling. We are therefore developing a design point for a spheromak experiment that will be heated by adiabatic compression, utilizing the CORSICA and NIMROD codes as well as analytic modeling with target parameters R_initial =0.3m, R_final =0.1m, T_initial =0.2keV, T_final =1.8keV, n_initial =1019m-3 and n_final = 1021m-3, with radial convergence of C =3. This low convergence differentiates the concept from MTF with C =10 or more, since the plasma will be held in equilibrium throughout compression. We present results from CORSICA showing the placement of coils and passive structure to ensure stability during compression, and design of the capacitor bank needed to both form the target plasma and compress it. We specify target parameters for the compression in terms of plasma beta, formation efficiency and energy confinement. Work performed under DARPA grant N66001-14-1-4044.

  16. Power system development: Ocean Thermal Energy Conversion (OTEC). Preliminary design report: appendices, Part 2 (Final)

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-12-04

    The objective of this project is the development of a preliminary design for a full-sized, closed cycle, ammonia power system module for the 100 MWe OTEC demonstration plant. In turn, this demonstration plant is to demonstrate, by 1984, the operation and performance of an Ocean Thermal Power Plant having sufficiently advanced heat exchanger design to project economic viability for commercial utilization in the late 1980's and beyond. Included in this power system development are the preliminary designs for a proof-of-concept pilot plant and test article heat exchangers which are scaled in such a manner as to support a logically sequential, relatively low-cost development of the full-scale power system module. The conceptual designs are presented for the demonstration plant power module, the proof-of-concept pilot plant, and for a pair of test article heat exchangers. Costs associated with the design, development, fabrication, checkout, delivery, installation, and operation are included. The accompanying design and producibilty studies on the full-scale power system module project the performance/economics for the commercial plant. This section of the report contains appendices on the electrical system, instrumentation and control, ammonia pump evaluation study, ammonia and nitrogen support subsystems, piping and support design calculations, and plant availability. (WHK)

  17. Preliminary Reactor Head Bolt Design of Prototype Sodium-cooled Fast Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Han, Insu; Koo, Gyeonghoi [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-05-15

    As structural requirements, the reactor head is designed to withstand all of the pressure, temperatures and forces which are likely to be imposed on it. The bolts that fasten the head to the vessel flange. Design of the reactor head bolts so as to withstand the loads applied should be designed. Currently, preliminary design of the PGSFR reactor bolts is progressed. So far, we have designed and evaluated example. The number and cross-sectional areas of bolts were determined using the procedure given in ASME BPVC Section III, Division 1, Appendix E. The purpose of this study is to conduct design the number and cross-sectional area of bolts attaching the PGSFR reactor head to the reactor vessel, using the ASME procedure. In this paper, preliminary bolt design for PGSFR was carried out according to the ASME procedure. Detailed calculations were carried out for bolt root diameter = 80 mm and number of bolts Nb = 45. It should be noted that the seating pressure recommended in the ASME code is only a suggested value, not mandatory appendix E. It does not guarantee a leak-tight joint. So these quantities are needed to carry out fatigue analysis of the bolts and to assure leak tightness of the joint during operation. For the future work, the fatigue and seismic analysis will be performed.

  18. SLUDGE TREATMENT PROJECT ENGINEERED CONTAINER RETRIEVAL AND TRANSFER SYSTEM PRELIMINARY DESIGN HAZARD ANALYSIS SUPPLEMENT 1

    Energy Technology Data Exchange (ETDEWEB)

    FRANZ GR; MEICHLE RH

    2011-07-18

    This 'What/If' Hazards Analysis addresses hazards affecting the Sludge Treatment Project Engineered Container Retrieval and Transfer System (ECRTS) NPH and external events at the preliminary design stage. In addition, the hazards of the operation sequence steps for the mechanical handling operations in preparation of Sludge Transport and Storage Container (STSC), disconnect STSC and prepare STSC and Sludge Transport System (STS) for shipping are addressed.

  19. Preliminary Failure Modes and Effects Analysis of the US Massive Gas Injection Disruption Mitigation System Design

    Energy Technology Data Exchange (ETDEWEB)

    Lee C. Cadwallader

    2013-10-01

    This report presents the results of a preliminary failure modes and effects analysis (FMEA) of a candidate design for the ITER Disruption Mitigation System. This candidate is the Massive Gas Injection System that provides machine protection in a plasma disruption event. The FMEA was quantified with “generic” component failure rate data as well as some data calculated from operating facilities, and the failure events were ranked for their criticality to system operation.

  20. Preliminary design of a public transportation system to support a theme park

    OpenAIRE

    Malacane, Christine Ann

    1994-01-01

    The purpose of this project was to develop the preliminary design of a public transportation system (PTS) that would support a theme park. Disney's America, a theme park originally planned for Northern Virginia, was used as the basis for this project. The problem was that the primary interstate that serves the park site was already overcrowded; this project was intended to expand the realm of possible transportation solutions to include public-transit solutions. The following report identi...

  1. Prior experience and its effects on audience design

    OpenAIRE

    Wilson, Kerry

    2008-01-01

    PRIOR EXPERIENCE AND ITS EFFECTS ON AUDIENCE DESIGN. Abstract Objective Audience design involves tailoring utterances to suit the needs of your partner. The current experiment was interested in whether a speaker’s experience has an impact on their use of audience design as a conversational tool and whether a speaker can transfer knowledge gained in one task across to a similar task. Design Two description tasks were used to investigate audience design by recording the numbe...

  2. BIOMEX (Biology and Mars Experiment): Preliminary results on Antarctic black cryptoendolithic fungi in ground based experiments

    OpenAIRE

    C. Pacelli; Selbmann, L.; S. Onofri; de Vera, J.P.P.

    2014-01-01

    The main goal for astrobiologists is to find traces of present or past life in extraterrestrial environment or in meteorites. Biomolecules, such as lipids, pigments or polysaccharides, may be useful to establish the presence of extant or extinct life (Simoneit, B et al., 1998). BIOMEX (Biology and Mars Experiment) aims to measure to what extent biomolecules, such as pigments and cellular components, preserve their stability under space and Mars-like conditions. The experiment has just been la...

  3. The Thirty Gigahertz Instrument Receiver for the QUIJOTE Experiment: Preliminary Polarization Measurements and Systematic-Error Analysis

    Science.gov (United States)

    Casas, Francisco J.; Ortiz, David; Villa, Enrique; Cano, Juan L.; Cagigas, Jaime; Pérez, Ana R.; Aja, Beatriz; Terán, J. Vicente; de la Fuente, Luisa; Artal, Eduardo; Hoyland, Roger; Génova-Santos, Ricardo

    2015-01-01

    This paper presents preliminary polarization measurements and systematic-error characterization of the Thirty Gigahertz Instrument receiver developed for the QUIJOTE experiment. The instrument has been designed to measure the polarization of Cosmic Microwave Background radiation from the sky, obtaining the Q, U, and I Stokes parameters of the incoming signal simultaneously. Two kinds of linearly polarized input signals have been used as excitations in the polarimeter measurement tests in the laboratory; these show consistent results in terms of the Stokes parameters obtained. A measurement-based systematic-error characterization technique has been used in order to determine the possible sources of instrumental errors and to assist in the polarimeter calibration process. PMID:26251906

  4. The Thirty Gigahertz Instrument Receiver for the QUIJOTE Experiment: Preliminary Polarization Measurements and Systematic-Error Analysis

    Directory of Open Access Journals (Sweden)

    Francisco J. Casas

    2015-08-01

    Full Text Available This paper presents preliminary polarization measurements and systematic-error characterization of the Thirty Gigahertz Instrument receiver developed for the QUIJOTE experiment. The instrument has been designed to measure the polarization of Cosmic Microwave Background radiation from the sky, obtaining the Q, U, and I Stokes parameters of the incoming signal simultaneously. Two kinds of linearly polarized input signals have been used as excitations in the polarimeter measurement tests in the laboratory; these show consistent results in terms of the Stokes parameters obtained. A measurement-based systematic-error characterization technique has been used in order to determine the possible sources of instrumental errors and to assist in the polarimeter calibration process.

  5. Preliminary experience with Piccolo Composite™, a radiolucent distal fibula plate, in ankle fractures.

    Science.gov (United States)

    Caforio, Marco; Perugia, Dario; Colombo, Massimiliano; Calori, Giorgio Maria; Maniscalco, Pietro

    2014-12-01

    The radiolucent plate has many advantageous properties in the treatment of complex ankle fractures, particularly trimalleolar fractures. Surgeons may sometimes have difficulty observing the posterior malleolus after synthesis of lateral malleolus with a traditional plate because common materials of conventional plates are not radiolucent. In this study, the authors highlight the importance of the radiolucent property in the treatment of ankle fractures and describe their preliminary experience with a carbon fibre-reinforced polyetheretherketone distal fibula plate, with good results at 4 months' follow-up and no signs of tissue inflammatory reaction.

  6. Percutaneous pulmonary valve implantation in a single artery branch: A preliminary experience

    Institute of Scientific and Technical Information of China (English)

    Massimo; Chessa; Gianfranco; Butera; Luca; Giugno; Angelo; Micheletti; Diana; G; Negura; Mario; Carminati

    2015-01-01

    To describe preliminary experience of percutaneous pulmonary valve implantation, in a single pulmonary branch position. Two procedures in 2 patients from a single center are described, where implantation of percutaneous valves within a single pulmonary artery branch was technically successful. The procedural indication was pulmonary valve regurgitation and/or residual stenosis. The 2 patients were symptomatic. An Edwards Sapien? valve(Patient 1), and a Medtronic Melody? valve(Patient 2) were implanted. Both pts were discharged with an excellent valve function. In this report it is underlined that this modality is technically feasible and may be considered an option in patients with congenital heart defect under special circumstances.

  7. Low-dose fetal CT for evaluation of severe congenital skeletal anomalies: preliminary experience

    Energy Technology Data Exchange (ETDEWEB)

    Victoria, Teresa; Epelman, Monica; Johnson, Ann M.; Kramer, Sandra; Jaramillo, Diego [Children' s Hospital of Philadelphia, Diagnostic Imaging, Philadelphia, PA (United States); Bebbington, Michael [Children' s Hospital of Philadelphia, Center for Fetal Diagnosis and Treatment, Philadelphia, PA (United States); Wilson, R.D. [University of Calgary, Obstetrics and Gynecology, Calgary (Canada)

    2012-01-15

    Congenital skeletal abnormalities compose a heterogeneous and complex group of conditions that affect bone growth and development and result in various anomalies in shape and size of the skeleton. Prenatal sonographic diagnosis of these anomalies is challenging because of the relative rarity of each skeletal dysplasia, the multitude of differential diagnoses encountered when the bony abnormalities are identified, lack of precise molecular diagnosis and the fact that many of these disorders have overlapping features and marked phenotypic variability. The following review is a preliminary summary of our experience at the Children's Hospital of Philadelphia (CHOP) using low-dose fetal CT in the evaluation of severe fetal osseous abnormalities. (orig.)

  8. Preliminary design of an advanced Stirling system for terrestrial solar energy conversion

    Science.gov (United States)

    White, M. A.; Noble, J. E.; Emigh, S. G.; Ross, B. A.; Lehmann, G. A.

    1990-01-01

    A preliminary design was generated for an advanced Stirling conversion system (ASCS) that will be capable of delivering about 25 kW of electric power to an electric utility grid. Stirling engines are being evaluated for terrestrial solar applications. A two-year task to complete detailed design, fabrication, assembly and testing of an ASCS prototype began in April, 1990. The ASCS is designed to deliver maximum power per year over a range of solar inputs with a design life of 30 years (60,000 h). The ACSC has a long-term cost goal of about $450 per kilowatt, exclusive of the 11-m parabolic dish concentrator. The proposed system includes a Stirling engine with high-pressure hydraulic output, coupled with a bent axis variable displacement hydraulic motor and a rotary induction generator. The major thrusts of the preliminary design are described, including material selection for the hot-end components, heat transport system (reflux pool boiler) design, system thermal response, improved manufacturability, FMECA/FTA analysis, updated manufacturing cost estimate, and predicted system performance.

  9. Development of an Exploration-Class Cascade Distillation System: Flight Like Prototype Preliminary Design

    Science.gov (United States)

    Callahan, Michael R.; Sargusingh, Miriam J.

    2015-01-01

    The ability to recover and purify water through physiochemical processes is crucial for realizing long-term human space missions, including both planetary habitation and space travel. Because of their robust nature, distillation systems have been actively pursued as one of the technologies for water recovery. One such technology is the Cascade Distillation System (CDS) a multi-stage vacuum rotary distiller system designed to recover water in a microgravity environment. Its rotating cascading distiller operates similarly to the state of the art (SOA) vapor compressor distiller (VCD), but its control scheme and ancillary components are judged to be straightforward and simpler to implement into a successful design. Through the Advanced Exploration Systems (AES) Life Support Systems (LSS) Project, the NASA Johnson Space Center (JSC) in collaboration with Honeywell International is developing a second generation flight forward prototype (CDS 2.0). The key objectives for the CDS 2.0 design task is to provide a flight forward ground prototype that demonstrates improvements over the SOA system in the areas of increased reliability and robustness, and reduced mass, power and volume. It will also incorporate exploration-class automation. The products of this task are a preliminary flight system design and a high fidelity prototype of an exploration class CDS. These products will inform the design and development of the third generation CDS which is targeted for on-orbit DTO. This paper details the preliminary design of the CDS 2.0.

  10. Preliminary Design Report of Fluid System of PDRC Performance Test Facility

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Tae-Ho; Eoh, Jae-Hyuk; Seong, Seung-Hwan; Han, Ji-Woong; Choi, Byoung-Hae; Kim, Seong-O

    2008-10-15

    PDRC (Passive Decay Heat Removal Circuit) is a safety grade passive residual heat removal system of KALIMER-600. In order to assess the long- and short-term cooling capabilities of PDRC and produce the experimental data for the verification of the performance and safety analysis codes, PDRC performance test was planned for. In this study, the overall design requirements and the preliminary design data for the fluid system of test facility are presented. The fluid system of the facility is composed of the primary heat transport system, the PDRC, the IHX air cooling system and the sodium supply/purification system. The preliminarily designed facility is scaled-down to 1/4 for length, 1/400 for volume from the primary heat transport system and the PDRC of KALIMER-600 based on a reliable scaling method. It can simulate the cooling of primary heat transport system for the full temperature condition in case of the reactor and pump trips. The produced preliminary design data will be used in the future as the basic information for a detailed design, an establishment of experimental requirement and an assessment of the appropriateness of facility design.

  11. A Framework for Preliminary Design of Aircraft Structures Based on Process Information. Part 1

    Science.gov (United States)

    Rais-Rohani, Masoud

    1998-01-01

    This report discusses the general framework and development of a computational tool for preliminary design of aircraft structures based on process information. The described methodology is suitable for multidisciplinary design optimization (MDO) activities associated with integrated product and process development (IPPD). The framework consists of three parts: (1) product and process definitions; (2) engineering synthesis, and (3) optimization. The product and process definitions are part of input information provided by the design team. The backbone of the system is its ability to analyze a given structural design for performance as well as manufacturability and cost assessment. The system uses a database on material systems and manufacturing processes. Based on the identified set of design variables and an objective function, the system is capable of performing optimization subject to manufacturability, cost, and performance constraints. The accuracy of the manufacturability measures and cost models discussed here depend largely on the available data on specific methods of manufacture and assembly and associated labor requirements. As such, our focus in this research has been on the methodology itself and not so much on its accurate implementation in an industrial setting. A three-tier approach is presented for an IPPD-MDO based design of aircraft structures. The variable-complexity cost estimation methodology and an approach for integrating manufacturing cost assessment into design process are also discussed. This report is presented in two parts. In the first part, the design methodology is presented, and the computational design tool is described. In the second part, a prototype model of the preliminary design Tool for Aircraft Structures based on Process Information (TASPI) is described. Part two also contains an example problem that applies the methodology described here for evaluation of six different design concepts for a wing spar.

  12. Integrating conceptualizations of experience into the interaction design process

    DEFF Research Database (Denmark)

    Dalsgaard, Peter

    2010-01-01

    From a design perspective, the increasing awareness of experiential aspects of interactive systems prompts the question of how conceptualizations of experience can inform and potentially be integrated into the interaction design process. This paper presents one approach to integrating theoretical...... perspectives on experience in design by formulating conceptual constructs that can guide design decisions....

  13. Preliminary design study of a quiet, high flow fan (QHF) stage. [turbofans - quiet engine program

    Science.gov (United States)

    Walker, C. L.; Kisner, L. S.; Delaney, R. A.; Beguhn, A. A.; Frye, D. E.

    1974-01-01

    Concepts selected to reduce fan generated noise in a turbofan are presented. Near-sonic flow at the fan inlet to reduce upstream propagated noise and the use of long-chord vanes to reduce downstream noise is discussed. The near-sonic condition at the rotor inlet plane was achieved by designing for high specific mass flow and by maintaining the high flow at reduced power by variable stators and variable fan exhaust nozzle. The long-chord vanes reduce response to unsteady flow. The acoustic design showed that long-chord stators would significantly reduce turbofan source noise and that other stator design parameters have no appreciable effect on noise for the spacing and chord length of the turbofan design. Four rig flow paths studied in the aerodynamic preliminary design are discussed. Noise prediction results indicate that a turbofan powered aircraft would be under federal air regulations levels without any acoustic treatment.

  14. The DESI Experiment Part II: Instrument Design

    CERN Document Server

    Aghamousa, Amir; Ahlen, Steve; Alam, Shadab; Allen, Lori E; Prieto, Carlos Allende; Annis, James; Bailey, Stephen; Balland, Christophe; Ballester, Otger; Baltay, Charles; Beaufore, Lucas; Bebek, Chris; Beers, Timothy C; Bell, Eric F; Bernal, José Luis; Besuner, Robert; Beutler, Florian; Blake, Chris; Bleuler, Hannes; Blomqvist, Michael; Blum, Robert; Bolton, Adam S; Briceno, Cesar; Buckley-Geer, Elizabeth; Burden, Angela; Burtin, Etienne; Busca, Nicolas G; Cahn, Robert N; Cai, Yan-Chuan; Carlberg, Raymond G; Carton, Pierre-Henri; Casas, Ricard; Castander, Francisco J; Claybaugh, Todd M; Close, Madeline; Coker, Carl T; Cole, Shaun; Cooper, Andrew P; Cousinou, M -C; Crocce, Martin; Cuby, Jean-Gabriel; Cunningham, Daniel P; Davis, Tamara; Dawson, Kyle S; de la Macorra, Axel; De Vicente, Juan; Delubac, Timothée; Derwent, Mark; Dey, Arjun; Dhungana, Govinda; Ding, Zhejie; Duan, Yutong T; Ealet, Anne; Edelstein, Jerry; Eftekharzadeh, Sarah; Eisenstein, Daniel J; Elliott, Ann; Escoffier, Stephanie; Evatt, Matthew; Fagrelius, Parker; Fan, Xiaohui; Fanning, Kevin; Farahi, Arya; Favole, Ginevra; Feng, Yu; Fernandez, Enrique; Findlay, Joseph R; Finkbeiner, Douglas P; Fitzpatrick, Michael J; Flaugher, Brenna; Flender, Samuel; Font-Ribera, Andreu; Forero-Romero, Jaime E; Fosalba, Pablo; Frenk, Carlos S; Fumagalli, Michele; Garcia-Bellido, Juan; Gaztanaga, Enrique; Gershkovich, Irina; Gillet, Denis; Gonzalez-de-Rivera, Guillermo; Gonzalez-Perez, Violeta; Gott, Shelby; Graur, Or; Gutierrez, Gaston; Guy, Julien; Habib, Salman; Heetderks, Henry; Heetderks, Ian; Heitmann, Katrin; Hellwing, Wojciech A; Herrera, David A; Ho, Shirley; Honscheid, Klaus; Huff, Eric; Hutchinson, Timothy A; Huterer, Dragan; Hwang, Ho Seong; Laguna, Joseph Maria Illa; Ishikawa, Yuzo; Jacobs, Dianna; Jeffrey, Niall; Jelinsky, Patrick; Jiang, Linhua; Jimenez, Jorge; Johnson, Jennifer; Joyce, Richard; Jullo, Eric; Juneau, Stephanie; Kama, Sami; Karcher, Armin; Karkar, Sonia; Kehoe, Robert; Kennamer, Noble; Kent, Stephen; Kilbinger, Martin; Kim, Alex G; Kirkby, David; Kisner, Theodore; Kitanidis, Ellie; Kneib, Jean-Paul; Koposov, Sergey; Kovacs, Eve; Kremin, Anthony; Kron, Richard; Kronig, Luzius; Kueter-Young, Andrea; Lacey, Cedric G; Lafever, Robin; Lahav, Ofer; Lambert, Andrew; Landriau, Martin; Lang, Dustin; Name, Publication; Lauer, Tod R; Goff, Jean-Marc Le; Guillou, Laurent Le; Van Suu, Auguste Le; Lee, Jae Hyeon; Lee, Su-Jeong; Leitner, Daniela; Levi, Michael E; L'Huillier, Benjamin; Li, Baojiu; Liang, Ming; Lin, Huan; Linder, Eric; Loebman, Sarah R; Lukić, Zarija; MacCrann, Niall; Magneville, Christophe; Makarem, Laleh; Manera, Marc; Manser, Christopher J; Marshall, Robert; Martini, Paul; Massey, Richard; Matheson, Thomas; McCauley, Jeremy; McDonald, Patrick; McGreer, Ian D; Meisner, Aaron; Metcalfe, Nigel; Miller, Timothy N; Miquel, Ramon; Moustakas, John; Myers, Adam; Naik, Milind; Newman, Jeffrey; Nichol, Robert C; Nicola, Andrina; da Costa, Luiz Nicolati; Niz, Gustavo; Norberg, Peder; Nord, Brian; Norman, Dara; Nugent, Peter; O'Brien, Thomas; Oh, Minji; Olsen, Knut A G; Padilla, Cristobal; Padmanabhan, Hamsa; Padmanabhan, Nikhil; Palanque-Delabrouille, Nathalie; Palmese, Antonella; Pappalardo, Daniel; Park, Changbom; Patej, Anna; Peacock, John A; Peiris, Hiranya V; Percival, Will J; Perruchot, Sandrine; Pieri, Matthew M; Pogge, Richard; Poppett, Claire; Probst, Ronald G; Rabinowitz, David; Ree, Chang Hee; Refregier, Alexandre; Regal, Xavier; Reid, Beth; Reil, Kevin; Rezaie, Mehdi; Rockosi, Connie; Roe, Natalie; Ronayette, Samuel; Roodman, Aaron; Ross, Ashley J; Ross, Nicholas P; Rossi, Graziano; Rozo, Eduardo; Ruhlmann-Kleider, Vanina; Rykoff, Eli; Sabiu, Cristiano; Samushia, Lado; Sanchez, Javier; Schlegel, David J; Schneider, Michael; Schubnell, Michael; Secroun, Aurélia; Seljak, Uros; Seo, Hee-Jong; Serrano, Santiago; Shafieloo, Arman; Shan, Huanyuan; Sholl, Michael J; Shourt, William V; Silber, Joseph H; Silva, David R; Sirk, Martin M; Slosar, Anze; Smith, Alex; Smoot, George; Som, Debopam; Song, Yong-Seon; Sprayberry, David; Staten, Ryan; Stefanik, Andy; Tarle, Gregory; Tie, Suk Sien; Tinker, Jeremy L; Tojeiro, Rita; Valdes, Francisco; Valenzuela, Octavio; Valluri, Monica; Vargas-Magana, Mariana; Verde, Licia; Walker, Alistair R; Wang, Yuting; Weaver, Benjamin A; Weaverdyck, Curtis; Wechsler, Risa; Weinberg, David H; White, Martin; Yang, Qian; Yeche, Christophe; Zhao, Gong-Bo; Zheng, Yi; Zhu, Yaling; Zou, Hu; Zu, Ying

    2016-01-01

    DESI (Dark Energy Spectropic Instrument) is a Stage IV ground-based dark energy experiment that will study baryon acoustic oscillations and the growth of structure through redshift-space distortions with a wide-area galaxy and quasar redshift survey. The DESI instrument is a robotically-actuated, fiber-fed spectrograph capable of taking up to 5,000 simultaneous spectra over a wavelength range from 360 nm to 980 nm. The fibers feed ten three-arm spectrographs with resolution $R= \\lambda/\\Delta\\lambda$ between 2000 and 5500, depending on wavelength. The DESI instrument will be used to conduct a five-year survey designed to cover 14,000 deg$^2$. This powerful instrument will be installed at prime focus on the 4-m Mayall telescope in Kitt Peak, Arizona, along with a new optical corrector, which will provide a three-degree diameter field of view. The DESI collaboration will also deliver a spectroscopic pipeline and data management system to reduce and archive all data for eventual public use.

  15. New physical model design for Vapex experiments

    Energy Technology Data Exchange (ETDEWEB)

    Yazdani, A.; Maini, B.B. [Calgary Univ., AB (Canada)

    2004-07-01

    Solvent extraction is gaining much attention as an in-situ recovery method for difficult to produce heavy oil and tar sand deposits. Vapour extraction (VAPEX) is similar to the steam assisted gravity drainage (SAGD) process used in heavy oil production. In VAPEX, vaporized solvents are used instead of high temperature steam and the viscosity of the oil is reduced in situ. VAPEX is well suited for formations that are thin and where heat losses are unavoidable. It can be applied in the presence of overlying gas caps; bottom water aquifers; low thermal conductivity; high water saturation; clay swelling; and, formation damage. Modelling studies that use rectangular shaped models are limited at high reservoir pressures. This study presents a new design of physical models that overcomes this limitation. The annular space between two cylindrical pipes is used for developing slice-type and sand-filled models. This newly developed model is more compatible with high pressure. This paper compares results of VAPEX experiments using the cylindrical models and the rectangular models. The stabilized drainage rates from the newly developed cylindrical models are in very good agreement with those from the rectangular models. 16 refs., 3 tabs., 11 figs.

  16. Preliminary design package for residential heating/cooling system--Rankine air conditioner redesign

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-01

    This report contains a summary of the preliminary redesign and development of a marketable single-family heating and cooling system. The objectives discussed are the interim design and schedule status of the Residential (3-ton) redesign, problem areas and solutions, and the definition of plans for future design and development activities. The proposed system for a single-family residential heating and cooling system is a single-loop, solar-assisted, hydronic-to-warm-air heating subsystem with solar-assisted domestic water heating and a Rankine-driven expansion air-conditioning subsystem.

  17. Design and preliminary results of a fuel flexible industrial gas turbine combustor

    Science.gov (United States)

    Novick, A. S.; Troth, D. L.; Yacobucci, H. G.

    1981-01-01

    The design characteristics are presented of a fuel tolerant variable geometry staged air combustor using regenerative/convective cooling. The rich/quench/lean variable geometry combustor is designed to achieve low NO(x) emission from fuels containing fuel bound nitrogen. The physical size of the combustor was calculated for a can-annular combustion system with associated operating conditions for the Allison 570-K engine. Preliminary test results indicate that the concept has the potential to meet emission requirements at maximum continuous power operation. However, airflow sealing and improved fuel/air mixing are necessary to meet Department of Energy program goals.

  18. Design and preliminary results of a fuel flexible industrial gas turbine combustor

    Science.gov (United States)

    Novick, A. S.; Troth, D. L.; Yacobucci, H. G.

    1981-01-01

    The design characteristics are presented of a fuel tolerant variable geometry staged air combustor using regenerative/convective cooling. The rich/quench/lean variable geometry combustor is designed to achieve low NO(x) emission from fuels containing fuel bound nitrogen. The physical size of the combustor was calculated for a can-annular combustion system with associated operating conditions for the Allison 570-K engine. Preliminary test results indicate that the concept has the potential to meet emission requirements at maximum continuous power operation. However, airflow sealing and improved fuel/air mixing are necessary to meet Department of Energy program goals.

  19. Heat recovery and seed recovery development project: preliminary design report (PDR)

    Energy Technology Data Exchange (ETDEWEB)

    Arkett, A. H.; Alexander, K. C.; Bolek, A. D.; Blackman, B. K.; Kurrle, P. E.; Tram, S. V.; Warren, A. M.; Ziobrowski, A. J.

    1981-06-01

    The preliminary design and performance characteristics are described of the 20 MWt heat recovery and seed recovery (HRSR) system to be fabricated, installed, and evaluated to provide a technological basis for the design of commercial size HRSR systems for coal-fired open-cycle MHD power plants. The system description and heat and material balances, equipment description and functional requirements, controls, interfacing systems, and operation and maintenance are detailed. Appendices include: (1) recommended environmental requirements for compliance with federal and state of Tennessee regulations, (2) channel and diffuser simulator, (3) equipment arrangement drawings, and (4) channel and diffuser simulator barrel drawings. (WHK)

  20. Preliminary design package for residential heating/cooling system: Rankine air conditioner redesign

    Science.gov (United States)

    1978-01-01

    A summary of the preliminary redesign and development of a marketable single family heating and cooling system is presented. The interim design and schedule status of the residential (3-ton) redesign, problem areas and solutions, and the definition of plans for future design and development activities were discussed. The proposed system for a single-family residential heating and cooling system is a single-loop, solar-assisted, hydronic-to-warm-air heating subsystem with solar-assisted domestic water heating and a Rankine-driven expansion air-conditioning subsystem.

  1. The Spatial Vision Tree: A Generic Pattern Recognition Engine- Scientific Foundations, Design Principles, and Preliminary Tree Design

    Science.gov (United States)

    Rahman, Zia-ur; Jobson, Daniel J.; Woodell, Glenn A.

    2010-01-01

    New foundational ideas are used to define a novel approach to generic visual pattern recognition. These ideas proceed from the starting point of the intrinsic equivalence of noise reduction and pattern recognition when noise reduction is taken to its theoretical limit of explicit matched filtering. This led us to think of the logical extension of sparse coding using basis function transforms for both de-noising and pattern recognition to the full pattern specificity of a lexicon of matched filter pattern templates. A key hypothesis is that such a lexicon can be constructed and is, in fact, a generic visual alphabet of spatial vision. Hence it provides a tractable solution for the design of a generic pattern recognition engine. Here we present the key scientific ideas, the basic design principles which emerge from these ideas, and a preliminary design of the Spatial Vision Tree (SVT). The latter is based upon a cryptographic approach whereby we measure a large aggregate estimate of the frequency of occurrence (FOO) for each pattern. These distributions are employed together with Hamming distance criteria to design a two-tier tree. Then using information theory, these same FOO distributions are used to define a precise method for pattern representation. Finally the experimental performance of the preliminary SVT on computer generated test images and complex natural images is assessed.

  2. Advanced multi-frequency radar: Design, preliminary measurements and particle size distribution retrieval

    Science.gov (United States)

    Majurec, Ninoslav

    lower output power of klystron amplifiers (comparing to magnetrons) is compensated by use of pulse compression (linear FM). The problem of range sidelobes (pulse compression artifacts) has been solved by using appropriate windowing functions in the receiver. Satisfactory sidelobe suppression level of 45 dB has been demonstrated in the lab. The currently best achievable range resolution of the AMFR system is 30 m (corresponds to 5 MHz receiver BW, set by the sampling rate of the Analog-to-Digital card). During the design stage, various polarization schemes have been investigated. The polarization scheme analysis showed the switching polarization scheme to be the best suited for the AMFR system. The AMFR subsystems were partially finished in the winter of 2005. Some preliminary tests were conducted in January 2006. Antenna platform was fabricated in summer 2006. The final assembly took place in the fall of 2006. Early results are presented in the dissertation. These results were helpful in revealing of certain problems in the radar system (i.e. immediate processing computer synchronization) that needed to be addressed during system development. Stratiform rain event occurred on December 18 2006 has been analyzed in detail. A number of commonly used theoretical particle size distributions is presented. Furthermore, it is shown that a fully calibrated multi-frequency radar system has capability of separating scattering and attenuation effects. This was accomplished by fitting the theoretical models into the measured data. An alternative method of estimating rain rate that relies on the dual wavelength ratios is also presented. Although not as powerful as theoretical model fitting, it has its merits for off-zenith observations. During January 2007, AMFR system participated in the C3VP experiment (Canadian CloudSat/CALIPSO Validation Project) in south Ontario, Canada. Some of the data obtained during C3VP experiment has been analyzed and presented. Analysis of these two

  3. Ocean Thermal Energy Conversion power system development. Phase I: preliminary design. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-04

    Westinghouse has completed the Preliminary Design Phase for the Power System Development of the Ocean Thermal Energy Conversion (OTEC) Demonstration Plant project. This study included the development of a preliminary design for a Modular Application scaled power system (10MWe) and Heat Exchanger Test Articles, both based on the concept developed in the Conceptual Design Phase. The results of this study were used to improve the baseline design of the 50MWe module for the Commercial Size Power System, which was recommended for the demonstration plant by the conceptual design study. The 50MWe module was selected since it has the lowest cost, and since its size convincingly demonstrates that future economically viable commercial plants, having reliable operation with credible anticipated costs, are possible. Additional optimization studies on the size of the power system plus hull continue to identify 50MWe as the preferred minimum cost configuration. This study was limited to a closed cycle ammonia power system module, using a seawater temperature difference of 40/sup 0/F, and a surface platform/ship reference hull. This volume describes system operation, a complete test program to verify mechanical reliability and thermal performance, fabrication and installation operations, and a cost analysis. (WHK)

  4. The MSFC Collaborative Engineering Process for Preliminary Design and Concept Definition Studies

    Science.gov (United States)

    Mulqueen, Jack; Jones, David; Hopkins, Randy

    2011-01-01

    This paper describes a collaborative engineering process developed by the Marshall Space Flight Center's Advanced Concepts Office for performing rapid preliminary design and mission concept definition studies for potential future NASA missions. The process has been developed and demonstrated for a broad range of mission studies including human space exploration missions, space transportation system studies and in-space science missions. The paper will describe the design team structure and specialized analytical tools that have been developed to enable a unique rapid design process. The collaborative engineering process consists of integrated analysis approach for mission definition, vehicle definition and system engineering. The relevance of the collaborative process elements to the standard NASA NPR 7120.1 system engineering process will be demonstrated. The study definition process flow for each study discipline will be will be outlined beginning with the study planning process, followed by definition of ground rules and assumptions, definition of study trades, mission analysis and subsystem analyses leading to a standardized set of mission concept study products. The flexibility of the collaborative engineering design process to accommodate a wide range of study objectives from technology definition and requirements definition to preliminary design studies will be addressed. The paper will also describe the applicability of the collaborative engineering process to include an integrated systems analysis approach for evaluating the functional requirements of evolving system technologies and capabilities needed to meet the needs of future NASA programs.

  5. Preliminary design of a high speed civil transport: The Opus 0-001

    Science.gov (United States)

    1992-01-01

    Based on research into the technology and issues surrounding the design, development, and operation of a second generation High Speed Civil Transport, HSCT, the Opus 0-001 team completed the preliminary design of a sixty passenger, three engine aircraft. The design of this aircraft was performed using a computer program which the team wrote. This program automatically computed the geometric, aerodynamic, and performance characteristic of an aircraft whose preliminary geometry was specified. The Opus 0-001 aircraft was designed for a cruise Mach number of 2.2, a range of 4,700 nautical miles and its design was based in current or very near term technology. Its small size was a consequence of an emphasis on a profitable, low cost program, capable of delivering tomorrow's passengers in style and comfort at prices that make it an attractive competitor to both current and future subsonic transport aircraft. Several hundred thousand cases of Cruise Mach number, aircraft size and cost breakdown were investigated to obtain costs and revenues for which profit was calculated. The projected unit flyaway cost was $92.0 million per aircraft.

  6. Designing interactive technology for crowd experiences - beyond sanitization

    DEFF Research Database (Denmark)

    Veerasawmy, Rune

    2014-01-01

    This dissertation concerns the topic on designing interactive technology for crowd expe- riences. It takes the outset in the experience-oriented design approach within interaction design, exploring the research question how can we conceptually understand and design interactive technology for crowd...... in a conceptual model of social experiences that presents crowd experiences as a distinct type of social experience. This is different from what previously have been explored within experi- ence-oriented design. This dissertation is composed of four research papers framed by an overview that summarizes...... experience within interaction design. This dissertation introduces an understanding of crowd experience as a distinct type of social experiences driven by non-rational behavior. This conceptual understanding is established in the intersection between sociological crowd theory and a pragmatist perspective...

  7. China ADS sub-critical experimental assembly-Venus-1 and preliminary experiment

    Institute of Scientific and Technical Information of China (English)

    SHI Yongqian; ZHANG Wei; CAO Jian; QUAN Yanhui; LUO Huangda; WU Xiaofei; XIA Pu; LUO Zhanglin; ZHAO Zhixiang; DING Dazhao; LI Yiguo; ZHU Qinfu; XIA Haihong; LI Jien

    2007-01-01

    China's accelerator-driven sub-critical system (ADS) sub-critical experimental assembly--Venus-1 and the preliminary experiment is presented. The core of Venus-1 is a coupled one of a fast neutron zone and a thermal neutron zone. The fast neutron zone is at the centre of the core and formed by natural uranium fuel. A fast neutron spectrum field can be produced in the fast neutron zone and used for the transmutation of minor actinides (Mas). The thermal neutron zone surrounds the fast neutron zone and is formed by low-enriched uranium fuel. It is a fission zone. An epithermal neutron zone between the fast neutron zone and the thermal neutron zone can be established for the transmutation of longlived fission products (LLFP). On July 18, 2005, the first fuel element was loaded into the Venus-Ⅰ sub-critical assembly and some preliminary experiments about the subcritical neutronics were performed. The Venus-1 can be driven by an Am-Be source or other steady neutron source (Cf-252, D-D reaction and D-T reaction) to study the effect of the external neutron source with different energies or a D-T pulsed neutron source on the dynamic characteristics.

  8. Efficient preliminary floating offshore wind turbine design and testing methodologies and application to a concrete spar design.

    Science.gov (United States)

    Matha, Denis; Sandner, Frank; Molins, Climent; Campos, Alexis; Cheng, Po Wen

    2015-02-28

    The current key challenge in the floating offshore wind turbine industry and research is on designing economic floating systems that can compete with fixed-bottom offshore turbines in terms of levelized cost of energy. The preliminary platform design, as well as early experimental design assessments, are critical elements in the overall design process. In this contribution, a brief review of current floating offshore wind turbine platform pre-design and scaled testing methodologies is provided, with a focus on their ability to accommodate the coupled dynamic behaviour of floating offshore wind systems. The exemplary design and testing methodology for a monolithic concrete spar platform as performed within the European KIC AFOSP project is presented. Results from the experimental tests compared to numerical simulations are presented and analysed and show very good agreement for relevant basic dynamic platform properties. Extreme and fatigue loads and cost analysis of the AFOSP system confirm the viability of the presented design process. In summary, the exemplary application of the reduced design and testing methodology for AFOSP confirms that it represents a viable procedure during pre-design of floating offshore wind turbine platforms.

  9. Preliminary design and thermal analysis of device for finish cooling Jaffa biscuits in a.d. 'Jaffa'- Crvenka

    Directory of Open Access Journals (Sweden)

    Salemović Duško R.

    2015-01-01

    Full Text Available In this paper preliminary design of device for finish cooling chocolate topping of biscuits in A.D. 'Jaffa'- Crvenka was done. The proposed preliminary design followed by the required technological process of finish cooling biscuits and required parameters of process which was supposed to get and which represented part of project task. Thermal analysis was made and obtained percentage error between surface contact of the air and chocolate topping, obtained from heat balance and geometrical over proposed preliminary design, wasn't more than 0.67%. This is a preliminary design completely justified because using required length of belt conveyor receive required temperature of chocolate topping at the end of the cooling process.

  10. Experience economy meets business model design

    DEFF Research Database (Denmark)

    Gudiksen, Sune Klok; Smed, Søren Graakjær; Poulsen, Søren Bolvig

    2012-01-01

    companies automatically get a higher prize when offering an experience setting to the customer illustrated by the coffee example. Organizations that offer experiences still have an advantage but when an increasing number of organizations enter the experience economy the competition naturally gets tougher...

  11. Rayleigh-Taylor Instability within Sediment Layers Due to Gas Retention: Preliminary Theory and Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Gauglitz, Phillip A.; Wells, Beric E.; Buchmiller, William C.; Rassat, Scot D.

    2013-03-21

    In Hanford underground waste storage tanks, a typical waste configuration is settled beds of waste particles beneath liquid layers. The settled beds are typically composed of layers, and these layers can have different physical and chemical properties. One postulated configuration within the settled bed is a less-dense layer beneath a more-dense layer. The different densities can be a result of different gas retention in the layers or different degrees of settling and compaction in the layers. This configuration can experience a Rayleigh-Taylor (RT) instability where the less dense lower layer rises into the upper layer. Previous studies of gas retention and release have not considered potential buoyant motion within a settle bed of solids. The purpose of this report is to provide a review of RT instabilities, discuss predictions of RT behavior for sediment layers, and summarize preliminary experimental observations of RT instabilities in simulant experiments.

  12. Investigation of fracture-matrix interaction: Preliminary experiments in a simple system

    Energy Technology Data Exchange (ETDEWEB)

    Foltz, S.D. [New Mexico Univ., Albuquerque, NM (United States). Dept. of Physics and Astronomy; Tidwell, V.C.; Glass, R.J.; Sobolik, S.R. [Sandia National Labs., Albuquerque, NM (United States)

    1992-12-31

    Paramount to the modeling of unsaturated flow and transport through fractured porous media is a clear understanding of the processes controlling fracture-matrix interaction. As a first step toward such an understanding, two preliminary experiments have been performed to investigate the influence of matrix imbibition on water percolation through unsaturated fractures in the plane normal to the fracture. Test systems consisted of thin slabs of either tuff or an analog material cut by a single vertical fracture into which a constant fluid flux was introduced. Transient moisture content and solute concentration fields were imaged by means of x-ray absorption. Flow fields associated with the two different media were significantly different owing to differences in material properties relative to the imposed flux. Richards` equation was found to be a valid means of modeling the imbibition of water into the tuff matrix from a saturated fracture for the current experiment.

  13. Characterizing the Experimental Procedure in Science Laboratories: A Preliminary Step towards Students Experimental Design

    Science.gov (United States)

    Girault, Isabelle; d'Ham, Cedric; Ney, Muriel; Sanchez, Eric; Wajeman, Claire

    2012-01-01

    Many studies have stressed students' lack of understanding of experiments in laboratories. Some researchers suggest that if students design all or parts of entire experiment, as part of an inquiry-based approach, it would overcome certain difficulties. It requires that a procedure be written for experimental design. The aim of this paper is to…

  14. The Square Kilometre Array Science Data Processor. Preliminary compute platform design

    Science.gov (United States)

    Broekema, P. C.; van Nieuwpoort, R. V.; Bal, H. E.

    2015-07-01

    The Square Kilometre Array is a next-generation radio-telescope, to be built in South Africa and Western Australia. It is currently in its detailed design phase, with procurement and construction scheduled to start in 2017. The SKA Science Data Processor is the high-performance computing element of the instrument, responsible for producing science-ready data. This is a major IT project, with the Science Data Processor expected to challenge the computing state-of-the art even in 2020. In this paper we introduce the preliminary Science Data Processor design and the principles that guide the design process, as well as the constraints to the design. We introduce a highly scalable and flexible system architecture capable of handling the SDP workload.

  15. 1972 preliminary safety analysis report based on a conceptual design of a proposed repository in Kansas

    Energy Technology Data Exchange (ETDEWEB)

    Blomeke, J.O.

    1977-08-01

    This preliminary safety analysis report is based on a proposed Federal Repository at Lyons, Kansas, for receiving, handling, and depositing radioactive solid wastes in bedded salt during the remainder of this century. The safety analysis applies to a hypothetical site in central Kansas identical to the Lyons site, except that it is free of nearby salt solution-mining operations and bore holes that cannot be plugged to Repository specifications. This PSAR contains much information that also appears in the conceptual design report. Much of the geological-hydrological information was gathered in the Lyons area. This report is organized in 16 sections: considerations leading to the proposed Repository, design requirements and criteria, a description of the Lyons site and its environs, land improvements, support facilities, utilities, different impacts of Repository operations, safety analysis, design confirmation program, operational management, requirements for eventually decommissioning the facility, design criteria for protection from severe natural events, and the proposed program of experimental investigations. (DLC)

  16. Designing Experiments for Nonlinear Models - An Introduction

    OpenAIRE

    Johnson, Rachel T.; Montgomery, Douglas C.

    2009-01-01

    The article of record as published may be found at http://dx.doi.org/10.1002/qre.1063 We illustrate the construction of Bayesian D-optimal designs for nonlinear models and compare the relative efficiency of standard designs with these designs for several models and prior distributions on the parameters. Through a relative efficiency analysis, we show that standard designs can perform well in situations where the nonlinear model is intrinsically linear. However, if the model is non...

  17. [The use of nitric oxide during transport of newborns with critical respiratory insufficiency: own experience, preliminary report].

    Science.gov (United States)

    Ziebiński, Marek; Walas, Wojciech

    2002-01-01

    This preliminary report presents author's experience with inhaled nitric oxide during transport of newborns with critical respiratory insufficiency. The theoretical basis, indications and contraindications as well as principles of administration during transport are described. The required equipment and some technical aspects are discussed. A short preview of performed transportations is given. Preliminary data show, that use of NO during transport is very helpful in children with critical respiratory insufficiency.

  18. Research Initiatives and Preliminary Results In Automation Design In Airspace Management in Free Flight

    Science.gov (United States)

    Corker, Kevin; Lebacqz, J. Victor (Technical Monitor)

    1997-01-01

    The NASA and the FAA have entered into a joint venture to explore, define, design and implement a new airspace management operating concept. The fundamental premise of that concept is that technologies and procedures need to be developed for flight deck and ground operations to improve the efficiency, the predictability, the flexibility and the safety of airspace management and operations. To that end NASA Ames has undertaken an initial development and exploration of "key concepts" in the free flight airspace management technology development. Human Factors issues in automation aiding design, coupled aiding systems between air and ground, communication protocols in distributed decision making, and analytic techniques for definition of concepts of airspace density and operator cognitive load have been undertaken. This paper reports the progress of these efforts, which are not intended to definitively solve the many evolving issues of design for future ATM systems, but to provide preliminary results to chart the parameters of performance and the topology of the analytic effort required. The preliminary research in provision of cockpit display of traffic information, dynamic density definition, distributed decision making, situation awareness models and human performance models is discussed as they focus on the theme of "design requirements".

  19. Research Initiatives and Preliminary Results In Automation Design In Airspace Management in Free Flight

    Science.gov (United States)

    Corker, Kevin; Lebacqz, J. Victor (Technical Monitor)

    1997-01-01

    The NASA and the FAA have entered into a joint venture to explore, define, design and implement a new airspace management operating concept. The fundamental premise of that concept is that technologies and procedures need to be developed for flight deck and ground operations to improve the efficiency, the predictability, the flexibility and the safety of airspace management and operations. To that end NASA Ames has undertaken an initial development and exploration of "key concepts" in the free flight airspace management technology development. Human Factors issues in automation aiding design, coupled aiding systems between air and ground, communication protocols in distributed decision making, and analytic techniques for definition of concepts of airspace density and operator cognitive load have been undertaken. This paper reports the progress of these efforts, which are not intended to definitively solve the many evolving issues of design for future ATM systems, but to provide preliminary results to chart the parameters of performance and the topology of the analytic effort required. The preliminary research in provision of cockpit display of traffic information, dynamic density definition, distributed decision making, situation awareness models and human performance models is discussed as they focus on the theme of "design requirements".

  20. Applying experience reports in design education: Challenges and ideas

    NARCIS (Netherlands)

    Pasman, G.J.; Romero Herrera, N.A.

    2013-01-01

    What if both design students and design tutors could have real-time insights into how students actually experience their design process rather than after-the-fact reflections? And what if these insights could be applied in ways that would contribute to more in-depth learning experiences? This paper

  1. Detailed design package for design of a video system providing optimal visual information for controlling payload and experiment operations with television

    Science.gov (United States)

    1975-01-01

    A detailed description of a video system for controlling space shuttle payloads and experiments is presented in the preliminary design review and critical design review, first and second engineering design reports respectively, and in the final report submitted jointly with the design package. The material contained in the four subsequent sections of the package contains system descriptions, design data, and specifications for the recommended 2-view system. Section 2 contains diagrams relating to the simulation test configuration of the 2-view system. Section 3 contains descriptions and drawings of the deliverable breadboard equipment. A description of the recommended system is contained in Section 4 with equipment specifications in Section 5.

  2. Designing mobile experiences for collocated interaction

    OpenAIRE

    Lundgren, Sus; Fischer, Joel; Reeves, Stuart; Torgersson, Olof

    2015-01-01

    Many of our everyday social interactions involve mobile devices. Yet, these tend to only provide good support for distributed social interactions. Although much HCI and CSCW research has explored how we might support collocated, face-to-face situations using mobile devices, much of this work exists as isolated exemplars of technical systems and / or interaction designs. This paper draws on a range of such exemplars to develop a practical design framework intended for guiding the design of new...

  3. Design Experiments and the Generation of Theory

    DEFF Research Database (Denmark)

    Nortvig, Anne-Mette

    2014-01-01

    When blended learning is introduced in professional education with strong traditions of physical activities and face-to-face interactions in the classroom, creation of new learning designs is needed both in the classroom and online. While some educators see the implementation of e...... methodology (DBR) and a participatory design approach was used in a case in physiotherapy education from the beginning of the implementation of e-learning in order to create learning designs for the new teaching context and generate theory in relation to this. Ict-based learning designs were created...

  4. Designing Effective Research Experiences for Undergraduates (Invited)

    Science.gov (United States)

    Jones Whyte, P.; Dalbotten, D. M.

    2009-12-01

    The undergraduate research experience has been recognized as a valuable component of preparation for graduate study. As competition for spaces in graduate schools become more keen students benefit from a formal introduction to the life of a scholar. Over the last twenty years a model of preparing students for graduate study with the research experience as the base has been refined at the University of Minnesota. The experience includes assignment with a faculty member and a series of seminars that support the experience. The seminars cover topics to include academic writing, scholarly literature review, writing of the abstract, research subject protection protocols, GRE test preparation, opportunities to interact with graduate student, preparing the graduate school application, and preparation of a poster to demonstrate the results of the research. The next phase of the process is to determine the role of the undergraduate research experience in the graduate school admission process.

  5. Basic requirements for a preliminary conceptual design of the Korea advanced pyroprocess facility (KAPF)

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Ho Hee; Ko, Won Il; Chang, Hong Lae; Song, Dae Yong; Kwon, Eun Ha; Lee, Jung Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2008-12-15

    Korea Atomic Energy Research Institute (KAERI) has been developing technologies for pyroprocessing for spent PWR fuels. This study is part of a long term R and D program in Korea to develop an advanced recycle system that has the potential to meet and exceed the proliferation resistance, waste minimization, resource minimization, safety and economic goals of approved Korean Government energy policy, as well as the Generation IV International Forum (GIF) program. To support this R and D program, KAERI requires that an independent estimate be made of the conceptual design and cost for construction and operation of a 'Korea Advanced Pyroprocessing Facility', This document describes the basic requirements for preliminary conceptual design of the Korea Advanced Pyroprocess Facility (KAPF). The presented requirements will be modified to be more effective and feasible on an engineering basis during the subsequent design process.

  6. V/STOL tilt rotor aircraft study. Volume 2: Preliminary design of research aircraft

    Science.gov (United States)

    1972-01-01

    A preliminary design study was conducted to establish a minimum sized, low cost V/STOL tilt-rotor research aircraft with the capability of performing proof-of-concept flight research investigations applicable to a wide range of useful military and commercial configurations. The analysis and design approach was based on state-of-the-art methods and maximum use of off-the-shelf hardware and systems to reduce development risk, procurement cost and schedules impact. The rotors to be used are of 26 foot diameter and are the same as currently under construction and test as part of NASA Tilt-Rotor Contract NAS2-6505. The aircraft has a design gross weight of 12,000 lbs. The proposed engines to be used are Lycoming T53-L-13B rated at 1550 shaft horsepower which are fully qualified. A flight test investigation is recommended which will determine the capabilities and limitations of the research aircraft.

  7. Preliminary Design of a Synchronized Narrow Bandwidth FEL for Taiwan Light Source

    CERN Document Server

    Keung Lau Wai; Ching Fan, Tai; Zone Hsiao Feng; Tung Hsu Kuo; Hwang, Ching Shiang; Cheng Kuo Chin; Huei Luo Guo; Jen Wang Duan; Ping Wang Jau; Huey Wang Min

    2004-01-01

    Design study of a narrow line-width, high power IR-FEL facility has been carried out at NSRRC. This machine is designed to synchronize with the U9 undulator radiation of Taiwan Light Source and therefore provide new opportunity for chemical dynamics and condensed matter research. It has been proposed to use a super-conducting linac to provide a 60 MeV high quality electron beam to drive a 2.5-10 microns FEL oscillator with U5 undulator. Operating this linac in energy recovery mode will also be considered as an option to improve overall system effeciency and reduce heat loss and radiation dosage at the beam dump. Performance requirements and outcomes from this preliminary design study will be reported.

  8. Preliminary optical design of an Active Optics test bench for space applications.

    Science.gov (United States)

    Calcines, A.; Bitenc, U.; Rolt, S.; Reeves, S.; Doelman, N.; Human, J.; Morris, T.; Myers, R.; Talbot, G.

    2017-03-01

    This communication presents a preliminary optical design for a test bench conceived within the European Space Agency's TRP project (Active Optics Correction Chain (AOCC) for large monolithic mirrors) with the goal of designing and developing an Active Optics system able to correct in space on telescopes apertures larger than 3 meters. The test bench design uses two deformable mirrors of 37.5 mm and 116 mm, the smallest mirror to generate aberrations and the largest one to correct them. The system is configured as a multi-functional test bench capable of verifying the performance of a Shack-Hartmann wavefront sensor as well as of a Phase Diversity based wavefront sensor. A third optical path leads to a high-order Shack-Hartmann wavefront sensor to monitor the entire system performance.

  9. Computation for the analysis of designed experiments

    CERN Document Server

    Heiberger, Richard

    2015-01-01

    Addresses the statistical, mathematical, and computational aspects of the construction of packages and analysis of variance (ANOVA) programs. Includes a disk at the back of the book that contains all program codes in four languages, APL, BASIC, C, and FORTRAN. Presents illustrations of the dual space geometry for all designs, including confounded designs.

  10. An Architectural Experience for Interface Design

    Science.gov (United States)

    Gong, Susan P.

    2016-01-01

    The problem of human-computer interface design was brought to the foreground with the emergence of the personal computer, the increasing complexity of electronic systems, and the need to accommodate the human operator in these systems. With each new technological generation discovering the interface design problems of its own technologies, initial…

  11. An Architectural Experience for Interface Design

    Science.gov (United States)

    Gong, Susan P.

    2016-01-01

    The problem of human-computer interface design was brought to the foreground with the emergence of the personal computer, the increasing complexity of electronic systems, and the need to accommodate the human operator in these systems. With each new technological generation discovering the interface design problems of its own technologies, initial…

  12. Preliminary CFD Analysis for HVAC System Design of a Containment Building

    Energy Technology Data Exchange (ETDEWEB)

    Son, Sung Man; Choi, Choengryul [ELSOLTEC, Yongin (Korea, Republic of); Choo, Jae Ho; Hong, Moonpyo; Kim, Hyungseok [KEPCO Engineering and Construction, Gimcheon (Korea, Republic of)

    2016-10-15

    HVAC (Heating, Ventilation, Air Conditioning) system has been mainly designed based on overall heat balance and averaging concepts, which is simple and useful for designing overall system. However, such a method has the disadvantage that cannot predict the local flow and temperature distributions in a containment building. In this study, a CFD (Computational Fluid Dynamics) preliminary analysis is carried out to obtain detailed flow and temperature distributions in a containment building and to ensure that such information can be obtained via CFD analysis. This approach can be useful for hydrogen analysis in an accident related to hydrogen released into a containment building. In this study, CFD preliminary analysis has been performed to obtain the detailed information of the reactor containment building by using the CFD analysis techniques and to ensure that such information can be obtained via CFD analysis. We confirmed that CFD analysis can offer enough detailed information about flow patterns and temperature field and that CFD technique is a useful tool for HVAC design of nuclear power plants.

  13. Euler Technology Assessment program for preliminary aircraft design employing SPLITFLOW code with Cartesian unstructured grid method

    Science.gov (United States)

    Finley, Dennis B.

    1995-01-01

    This report documents results from the Euler Technology Assessment program. The objective was to evaluate the efficacy of Euler computational fluid dynamics (CFD) codes for use in preliminary aircraft design. Both the accuracy of the predictions and the rapidity of calculations were to be assessed. This portion of the study was conducted by Lockheed Fort Worth Company, using a recently developed in-house Cartesian-grid code called SPLITFLOW. The Cartesian grid technique offers several advantages for this study, including ease of volume grid generation and reduced number of cells compared to other grid schemes. SPLITFLOW also includes grid adaptation of the volume grid during the solution convergence to resolve high-gradient flow regions. This proved beneficial in resolving the large vortical structures in the flow for several configurations examined in the present study. The SPLITFLOW code predictions of the configuration forces and moments are shown to be adequate for preliminary design analysis, including predictions of sideslip effects and the effects of geometry variations at low and high angles of attack. The time required to generate the results from initial surface definition is on the order of several hours, including grid generation, which is compatible with the needs of the design environment.

  14. Mountaineer Commercial Scale Carbon Capture and Storage Project Topical Report: Preliminary Public Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Guy Cerimele

    2011-09-30

    This Preliminary Public Design Report consolidates for public use nonproprietary design information on the Mountaineer Commercial Scale Carbon Capture & Storage project. The report is based on the preliminary design information developed during the Phase I - Project Definition Phase, spanning the time period of February 1, 2010 through September 30, 2011. The report includes descriptions and/or discussions for: (1) DOE's Clean Coal Power Initiative, overall project & Phase I objectives, and the historical evolution of DOE and American Electric Power (AEP) sponsored projects leading to the current project; (2) Alstom's Chilled Ammonia Process (CAP) carbon capture retrofit technology and the carbon storage and monitoring system; (3) AEP's retrofit approach in terms of plant operational and integration philosophy; (4) The process island equipment and balance of plant systems for the CAP technology; (5) The carbon storage system, addressing injection wells, monitoring wells, system monitoring and controls logic philosophy; (6) Overall project estimate that includes the overnight cost estimate, cost escalation for future year expenditures, and major project risks that factored into the development of the risk based contingency; and (7) AEP's decision to suspend further work on the project at the end of Phase I, notwithstanding its assessment that the Alstom CAP technology is ready for commercial demonstration at the intended scale.

  15. Preliminary Design of the Brazilian's National Institute for Space Research Broadband Radiometer for Solar Observations

    Science.gov (United States)

    Berni, L. A.; Vieira, L. E. A.; Savonov, G. S.; Dal Lago, A.; Mendes, O.; Silva, M. R.; Guarnieri, F.; Sampaio, M.; Barbosa, M. J.; Vilas Boas, J. V.; Branco, R. H. F.; Nishimori, M.; Silva, L. A.; Carlesso, F.; Rodríguez Gómez, J. M.; Alves, L. R.; Vaz Castilho, B.; Santos, J.; Silva Paula, A.; Cardoso, F.

    2017-10-01

    The Total Solar Irradiance (TSI), which is the total radiation arriving at Earth's atmosphere from the Sun, is one of the most important forcing of the Earths climate. Measurements of the TSI have been made employing instruments on board several space-based platforms during the last four solar cycles. However, combining these measurements is still challenging due to the degradation of the sensor elements and the long-term stability of the electronics. Here we describe the preliminary efforts to design an absolute radiometer based on the principle of electrical substitution that is under development at Brazilian's National Institute for Space Research (INPE).

  16. Energy efficient engine flight propulsion system preliminary analysis and design report

    Science.gov (United States)

    Gardner, W. B.

    1979-01-01

    A flight propulsion system preliminary design was established that meets the program goals of at least a 12 percent reduction in thrust specific fuel consumption, at least a five percent reduction in direct operating cost, and one-half the performance deterioration rate of the most efficient current commercial engines. The engine provides a high probability of meeting the 1978 noise rule goal. Smoke and gaseous emissions defined by the EPA proposed standards for engines newly certified after 1 January 1981 are met with the exception of NOx, despite incorporation of all known NOx reduction technology.

  17. Preliminary Design of Control Network for HT-7U Tokamak Cryogenic System

    Institute of Scientific and Technical Information of China (English)

    Jin Yibin(金毅彬); Zhuang Ming(庄明); Bai Hongyu(白宏宇)

    2003-01-01

    In the course of the cryoplant modernization, a control network will be set up in order to facilitate the control, the supervision, the centralized data acquisition and the alarm handling of the cryogenic system for HT-7U tokamak. The paper introduces the preliminary design of control network based on the Controller Link Network for HT-7U tokamak cryogenic system. The multi-layer structure mentioned in the paper is the mainstream of automatic control.The control philosophy, the structure of the network and the components for control are also presented.

  18. Preliminary test of effects of cognitive ability, experience, and teaching methods on Verbal Analogy Test scores.

    Science.gov (United States)

    Rosenberg, D; Willson-Quayle, A; Pasnak, R

    2000-06-01

    The methods from which one can choose when preparing for the GRE Verbal Analogies include books, software, audiotapes, and formal classroom instruction. What teaching method will work best for a given individual? To begin the search for an answer, Gray's test of reasoning ability was given to 28 undergraduates who also answered a questionnaire detailing their experience with analogies. They were randomly assigned to teaching conditions ranging from self-directed workbook study to intensive interactive assistance. No teaching method was superior overall, but interactions showed that (1) students who scored worst on the pretest improved the most, (2) those higher in cognitive functioning and experience performed better after intensive interactive assistance, and (3) those lower in both cognitive functioning and experience did significantly better with self-paced workbooks. This preliminary work suggests that it may be profitable to assess the prior experience and reasoning of potential students and adopt the methods for teaching formal operational thought found empirically to be most suitable.

  19. Preliminary Results from the PrimEx-II experiment at Jefferson Lab

    Energy Technology Data Exchange (ETDEWEB)

    Gasparian, Ashot [NCA& T, Greensboro, NC; Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

    2016-06-01

    Properties of the neutral pion, as the lightest hadron in Nature, are most sensitive to the basic symmetries and their partial breaking effects in the theory of the strong interaction (QCD). In particular, the po →gg decay width is primarily defined by the spontaneous chiral symmetry breaking effect (chiral anomaly) in QCD. The next order corrections to the anomaly have been shown to be small and are known to a 1% precision level. The PrimEx Collaboration at JLab has developed and performed two Primakoff type experiments to measure the po →gg decay width with a similar precision. The published result from the PrimEx-I experiment, G(p0 →gg ) = 7.82±0.14 (stat.)±0.17 (syst.) eV, was a factor of two more precise than the average value quoted in PDG-2010 [1]. The second experiment was performed in 2010 with a goal of 1.4% total uncertainty to address the next-to-leading-order theory calculations. The preliminary results from the PrimEx-II experiment are presented and discussed in this note.

  20. Preliminary design study of underground pumped hydro and compressed-air energy storage in hard rock. Volume 1: Executive summary

    Science.gov (United States)

    1981-05-01

    A preliminary design study of water compensated Compressed Air Energy Storage (CAES) and Underground Pumped Hydroelectric (UPH) plants for siting in geological conditions suitable for hard rock excavations was performed. The study was divided into five primary tasks as follows: establishment of design criteria and analysis of impact on power system; selection of site and establishment of site characteristics; formulation of design approaches; assessment of environmental and safety aspects; and preparation of preliminary design of plant. The salient aspects considered and the conclusions reached during the consideration of the five primary tasks for both CAES and UPH are presented.

  1. MCNP5 and GEANT4 comparisons for preliminary Fast Neutron Pencil Beam design at the University of Utah TRIGA system

    Science.gov (United States)

    Adjei, Christian Amevi

    The main objective of this thesis is twofold. The starting objective was to develop a model for meaningful benchmarking of different versions of GEANT4 against an experimental set-up and MCNP5 pertaining to photon transport and interactions. The following objective was to develop a preliminary design of a Fast Neutron Pencil Beam (FNPB) Facility to be applicable for the University of Utah research reactor (UUTR) using MCNP5 and GEANT4. The three various GEANT4 code versions, GEANT4.9.4, GEANT4.9.3, and GEANT4.9.2, were compared to MCNP5 and the experimental measurements of gamma attenuation in air. The average gamma dose rate was measured in the laboratory experiment at various distances from a shielded cesium source using a Ludlum model 19 portable NaI detector. As it was expected, the gamma dose rate decreased with distance. All three GEANT4 code versions agreed well with both the experimental data and the MCNP5 simulation. Additionally, a simple GEANT4 and MCNP5 model was developed to compare the code agreements for neutron interactions in various materials. Preliminary FNPB design was developed using MCNP5; a semi-accurate model was developed using GEANT4 (because GEANT4 does not support the reactor physics modeling, the reactor was represented as a surface neutron source, thus a semi-accurate model). Based on the MCNP5 model, the fast neutron flux in a sample holder of the FNPB is obtained to be 6.52×107 n/cm2s, which is one order of magnitude lower than gigantic fast neutron pencil beam facilities existing elsewhere. The MCNP5 model-based neutron spectrum indicates that the maximum expected fast neutron flux is at a neutron energy of ~1 MeV. In addition, the MCNP5 model provided information on gamma flux to be expected in this preliminary FNPB design; specifically, in the sample holder, the gamma flux is to be expected to be around 108 γ/cm 2s, delivering a gamma dose of 4.54×103 rem/hr. This value is one to two orders of magnitudes below the gamma

  2. Designing Technology for Active Spectator Experiences at Sporting Events

    DEFF Research Database (Denmark)

    Veerasawmy, Rune; Ludvigsen, Martin

    is not merely an experience of receiving and consuming entertainment. It is also heavily reliant on the active participation of the spectator in creating the atmosphere of the entire event. The BannerBattle experiment provides interactive technology in sport arenas with a form of interaction based on existing......This paper explores the active spectator experience at sporting events, by presenting and reflecting upon a design experiment carried out at a number of football1 events. The initial hypothesis of the design process, leading to the design experiment has been that the spectator experience...... behaviour in the context. The work presented also argues for a need to overcome the inclination to designing technological systems that imitate or compete with the experience of watching the television broadcast of the game. Experiments such as the presented BannerBattle are cornerstones in our exploratory...

  3. Preliminary Neutronic Design of High Burnup OTTO Cycle Pebble Bed Reactor

    Directory of Open Access Journals (Sweden)

    T. Setiadipura

    2015-04-01

    Full Text Available The pebble bed type High Temperature Gas-cooled Reactor (HTGR is among the interesting nuclear reactor designs in terms of safety and flexibility for co-generation applications. In addition, the strong inherent safety characteristics of the pebble bed reactor (PBR which is based on natural mechanisms improve the simplicity of the PBR design, in particular for the Once-Through-Then-Out (OTTO cycle PBR design. One of the important challenges of the OTTO cycle PBR design, and nuclear reactor design in general, is improving the nuclear fuel utilization which is shown by attaining a higher burnup value. This study performed a preliminary neutronic design study of a 200 MWt OTTO cycle PBR with high burnup while fulfilling the safety criteria of the PBR design.The safety criteria of the design was represented by the per-fuel-pebble maximum power generation of 4.5 kW/pebble. The maximum burnup value was also limited by the tested maximum burnup value which maintained the integrity of the pebble fuel. Parametric surveys were performed to obtain the optimized parameters used in this study, which are the fuel enrichment, per-pebble heavy metal (HM loading, and the average axial speed of the fuel. An optimum design with burnup value of 131.1 MWd/Kg-HM was achieved in this study which is much higher compare to the burnup of the reference design HTR-MODUL and a previously proposed OTTO-cycle PBR design. This optimum design uses 17% U-235 enrichment with 4 g HM-loading per fuel pebble

  4. A Photogate Design for Air Track Experiments.

    Science.gov (United States)

    Hinrichsen, P. F.

    1988-01-01

    Introduces a photogate arrangement using a photo-reflective sensor for air track experiments. Reports that the sensitivity to sunlight can be eliminated and a mechanically more convenient package produced. Shows the mounting, circuit, and usage of the photogate. (YP)

  5. The Design, Experience and Practice of Networked Learning

    DEFF Research Database (Denmark)

    Gleerup, Janne; Heilesen, Simon; Helms, Niels Henrik

    2014-01-01

    . The Design, Experience and Practice of Networked Learning will prove indispensable reading for researchers, teachers, consultants, and instructional designers in higher and continuing education; for those involved in staff and educational development, and for those studying post graduate qualifications...

  6. HACCP and water safety plans in Icelandic water supply: preliminary evaluation of experience.

    Science.gov (United States)

    Gunnarsdóttir, María J; Gissurarson, Loftur R

    2008-09-01

    Icelandic waterworks first began implementing hazard analysis and critical control points (HACCP) as a preventive approach for water safety management in 1997. Since then implementation has been ongoing and currently about 68% of the Icelandic population enjoy drinking water from waterworks with a water safety plan based on HACCP. Preliminary evaluation of the success of HACCP implementation was undertaken in association with some of the waterworks that had implemented HACCP. The evaluation revealed that compliance with drinking water quality standards improved considerably following the implementation of HACCP. In response to their findings, waterworks implemented a large number of corrective actions to improve water safety. The study revealed some limitations for some, but not all, waterworks in relation to inadequate external and internal auditing and a lack of oversight by health authorities. Future studies should entail a more comprehensive study of the experience with the use of HACCP with the purpose of developing tools to promote continuing success.

  7. Fetal magnetic resonance imaging: jumping from 1.5 to 3 tesla (preliminary experience)

    Energy Technology Data Exchange (ETDEWEB)

    Victoria, Teresa [The Children' s Hospital of Philadelphia, Radiology Department, Center for Fetal Diagnosis and Treatment, Philadelphia, PA (United States); Jaramillo, Diego; Roberts, Timothy Paul Leslie; Zarnow, Deborah; Johnson, Ann Michelle; Delgado, Jorge; Vossough, Arastoo [The Children' s Hospital of Philadelphia, Radiology Department, Philadelphia, PA (United States); Rubesova, Erika [Stanford University, Department of Radiology, Lucile Packard Children' s Hospital, Stanford, CA (United States)

    2014-04-15

    Several attempts have been made at imaging the fetus at 3 T as part of the continuous search for increased image signal and better anatomical delineation of the developing fetus. Until very recently, imaging of the fetus at 3 T has been disappointing, with numerous artifacts impeding image analysis. Better magnets and coils and improved technology now allow imaging of the fetus at greater magnetic strength, some hurdles in the shape of imaging artifacts notwithstanding. In this paper we present the preliminary experience of evaluating the developing fetus at 3 T and discuss several artifacts encountered and techniques to decrease them, as well as safety concerns associated with scanning the fetus at higher magnetic strength. (orig.)

  8. Post-depositional changes in snow isotope content: preliminary results of laboratory experiments

    Directory of Open Access Journals (Sweden)

    A. A. Ekaykin

    2009-10-01

    Full Text Available Isotopic content of the snow and firn thickness is assumed to be altered significantly due to the post-depositional (PD mass- and isotope exchange with the atmospheric water vapor. If so, these effects should be accounted for in the ice core-based isotope-temperature paleo-reconstructions. In order to study the intensity of the PD processes we set up a series of laboratory experiments. In this paper we describe in detail the experimental technique and briefly overview preliminary results. It is shown that the PD modifications in the upper layer of snow thickness are noticeably strong even under such a low temperature as −35°C (the value typical for the Central Antarctic summer. It is demonstrated that the PD isotopic changes in snow can be approximated as a linear function of the relative mass loss due to snow sublimation. Possible applications for improving the isotope-temperature paleo-reconstructions are shortly discussed.

  9. Statistical Analysis of Designed Experiments Theory and Applications

    CERN Document Server

    Tamhane, Ajit C

    2012-01-01

    A indispensable guide to understanding and designing modern experiments The tools and techniques of Design of Experiments (DOE) allow researchers to successfully collect, analyze, and interpret data across a wide array of disciplines. Statistical Analysis of Designed Experiments provides a modern and balanced treatment of DOE methodology with thorough coverage of the underlying theory and standard designs of experiments, guiding the reader through applications to research in various fields such as engineering, medicine, business, and the social sciences. The book supplies a foundation for the

  10. Hybrid Rocket Experiment Station for Capstone Design

    Science.gov (United States)

    Conley, Edgar; Hull, Bethanne J.

    2012-01-01

    Portable hybrid rocket motors and test stands can be seen in many papers but none have been reported on the design or instrumentation at such a small magnitude. The design of this hybrid rocket and test stand is to be small and portable (suitcase size). This basic apparatus will be used for demonstrations in rocket propulsion. The design had to include all of the needed hardware to operate the hybrid rocket unit (with the exception of the external Oxygen tank). The design of this project includes making the correlation between the rocket's thrust and its size, the appropriate transducers (physical size, resolution, range, and cost), compatability with a laptop analog card, the ease of setup, and its portability.

  11. User experience (UX) design for libraries

    CERN Document Server

    Schmidt, Aaron

    2012-01-01

    This book shows you how to get there by providing hands-on steps and best practices for UX design principles, practices, and tools to engage with patrons online and build the best web presence for your library.

  12. Design Experiments and the Generation of Theory

    DEFF Research Database (Denmark)

    Nortvig, Anne-Mette

    2014-01-01

    When blended learning is introduced in professional education with strong traditions of physical activities and face-to-face interactions in the classroom, creation of new learning designs is needed both in the classroom and online. While some educators see the implementation of e-learning and bl...... be rewarding to couple DBR with a grounded theory approach in order to be able both to capture the data that emerge in a project that follows its own agenda and to generate theory on a context that is changing....... methodology (DBR) and a participatory design approach was used in a case in physiotherapy education from the beginning of the implementation of e-learning in order to create learning designs for the new teaching context and generate theory in relation to this. Ict-based learning designs were created...

  13. Designing the user experience of game development tools

    CERN Document Server

    Lightbown, David

    2015-01-01

    The Big Green Button My Story Who Should Read this Book? Companion Website and Twitter Account Before we BeginWelcome to Designing the User Experience of Game Development ToolsWhat Will We Learn in This Chapter?What Is This Book About?Defining User ExperienceThe Value of Improving the User Experience of Our ToolsParallels Between User Experience and Game DesignHow Do People Benefit From an Improved User Experience?Finding the Right BalanceWrapping UpThe User-Centered Design ProcessWhat Will We

  14. Frictional sliding in layered rock: Preliminary experiments on stacked Lexan plates

    Energy Technology Data Exchange (ETDEWEB)

    Perry, K.E. Jr.; Epstein, J.S. [Idaho National Engineering Laboratory, Idaho Falls, ID (United States). Fracture Behavior Group; Jung, J. [Sandia National Labs., Albuquerque, NM (United States)

    1995-12-31

    Understanding the mechanical behavior of jointed-rock masses is of critical importance to designing and predicting the performance of a potential nuclear waste repositiry. To this end we have studied the frictional sliding between simulated rock joints using phase shifting moire interferometry. Preliminary calibration models were made from stacks of Lexan plates that were sand-blasted to provide a uniform frictional interface. Load was applied monotonically and phase shifted moire fringe patterns were recorded at three different load states. Plots of slip along the interfaces for the model are presented to demonstrate the ability of the photomechanics technique to provide precise measurements of in-plane displacement, and ultimately the slip between the plates.

  15. Thermal Characterization of Functionally Graded Materials: Design of Optimum Experiments

    Science.gov (United States)

    Cole, Kevin D.

    2003-01-01

    This paper is a study of optimal experiment design applied to the measure of thermal properties in functionally graded materials. As a first step, a material with linearly-varying thermal properties is analyzed, and several different tran- sient experimental designs are discussed. An optimality criterion, based on sen- sitivity coefficients, is used to identify the best experimental design. Simulated experimental results are analyzed to verify that the identified best experiment design has the smallest errors in the estimated parameters. This procedure is general and can be applied to design of experiments for a variety of materials.

  16. In Silico Analog Design for Terbinafine Against Trichophyton rubrum: A Preliminary Study.

    Science.gov (United States)

    Karumuri, Sudha; Singh, Puneet Kumar; Shukla, Pratyoosh

    2015-09-01

    The diseases caused by dermatophytes are common among several other infections which cause serious threat to human health. It is evident that enzyme squalene epoxidase is responsible for prolonged dermatophyte infection and it is appealing to note that this enzyme is also responsible for fatty acid synthesis in these groups of fungi. In the present study, terbinafine drug which targets enzyme squalene epoxidase has been explored to design its various novel analogues. The present study suggests that many more prominent drug analogues could be constituted which may be crucial towards designing new drug candidates. In the present study, we have designed a series of such analogues viz. [(2E)-6,6-dimethylhept-2-en-4-yn-1-yl](methyl)(naphthalen-1-ylmethyl)amine, N-[8-({[(2E)-6,6-dimethylhept-2-en-4-yn-1-yl](methyl)amino}methyl)naphthalen-1-yl]-2-(sulfoamino) acetamide, {[4-(dihydroxyamino)-8-({[(2E)-6,6-dimethylhept-2-en-4-yn-1-yl](methyl)amino}methyl)naphthalen-1-yl]sulfanyl}methanol and (R)-{[4-({[(2E,6R)-6,7-dimethyloct-2-en-4-yn-1-yl](methyl)amino}methyl)-5-[(hydroxysulfamoyl)amino]naphthalen-1-yl]amino}sulfinic acid. Moreover, further by molecular docking approach the binding between enzyme and designed analogues was further analysed. The present preliminary report suggested a considerably good docking interaction score of -338.75 kcal/mol between terbinafine and squalene epoxidase from Trichophyton rubrum. This preliminary study implies that few designed candidate ligands can be effectual towards the activity of this enzyme and can play crucial role in pathogenesis control of T. rubrum.

  17. Software requirements flow-down and preliminary software design for the G-CLEF spectrograph

    Science.gov (United States)

    Evans, Ian N.; Budynkiewicz, Jamie A.; DePonte Evans, Janet; Miller, Joseph B.; Onyuksel, Cem; Paxson, Charles; Plummer, David A.

    2016-08-01

    The Giant Magellan Telescope (GMT)-Consortium Large Earth Finder (G-CLEF) is a fiber-fed, precision radial velocity (PRV) optical echelle spectrograph that will be the first light instrument on the GMT. The G-CLEF instrument device control subsystem (IDCS) provides software control of the instrument hardware, including the active feedback loops that are required to meet the G-CLEF PRV stability requirements. The IDCS is also tasked with providing operational support packages that include data reduction pipelines and proposal preparation tools. A formal, but ultimately pragmatic approach is being used to establish a complete and correct set of requirements for both the G-CLEF device control and operational support packages. The device control packages must integrate tightly with the state-machine driven software and controls reference architecture designed by the GMT Organization. A model-based systems engineering methodology is being used to develop a preliminary design that meets these requirements. Through this process we have identified some lessons that have general applicability to the development of software for ground-based instrumentation. For example, tasking an individual with overall responsibility for science/software/hardware integration is a key step to ensuring effective integration between these elements. An operational concept document that includes detailed routine and non- routine operational sequences should be prepared in parallel with the hardware design process to tie together these elements and identify any gaps. Appropriate time-phasing of the hardware and software design phases is important, but revisions to driving requirements that impact software requirements and preliminary design are inevitable. Such revisions must be carefully managed to ensure efficient use of resources.

  18. A preliminary design of interior structure and foundation of an inflatable lunar habitat

    Science.gov (United States)

    Yin, Paul K.

    1989-01-01

    A preliminary structural design and analysis of an inflatable habitat for installation on the moon was completed. The concept takes the shape of a sphere with a diameter of approximately 16 meters. The interior framing provides five floor levels and is enclosed by a spherical air-tight membrane holding an interior pressure of 14.7 psi (101.4kpa). The spherical habitat is to be erected on the lunar surface with the lower one third below grade and the upper two thirds covered with a layer of lunar regolith for thermal insulation and shielding against radiation and meteoroids. The total dead weight (earth weight) of the structural aluminum, which is of vital interest for the costly space transportation, is presented. This structural dead weight represents a preliminary estimate without including structural details. The design results in two versions: one supports the weight of the radiation shielding in case of deflation of the fabric enclosure and the other assumes that the radiation shielding is self supporting. To gain some indication of the amount of structural materials needed if the identical habitat were installed on Mars and Earth, three additional design versions were generated where the only difference is in gravity. These additional design versions are highly academic since the difference will be much more than in gravity alone. The lateral loading due to dust storms on Mars and wind loads on Earth are some examples. The designs under the lunar gravity are realistic. They may not be adequate for final material procurement and fabrication, however, as the connection details, among other reasons, may effect the sizes of the structural members.

  19. Screening diagnostics of antivital experiences and propensity toward impulsive, autoagressive behavior in adolescents (preliminary results

    Directory of Open Access Journals (Sweden)

    Bannikov G.S.,

    2014-08-01

    Full Text Available Development of methods for revealing antivital experiences and propensity to autoaggressive behavior in educational institutions is one of the key steps in developing strategies for the primary prevention of suicidal behavior in adolescents. The purpose of this study was to develop an effective screening diagnostic package aimed at identifying antivital experiences and propensity to autoaggressive behavior. The survey methods we used were: Beck Hopelessness Scale, Russell Loneliness Scale, A.G. Shmelev Suicide Risk Questionnaire, PDQ-IV Borderline disorder and Narcissism scales. At the first stage we examined 750 minors aged 12-18 and identified risk group (85 people – 11.4%, which included adolescents with high levels of both individual scales, and their combination. At the second stage we examined 10 adolescents at risk. In 7 of them (70% were identified antivital, suicidal thoughts of passive or compulsive nature, signs of subjective and objective socio- psychological maladjustment. Our preliminary conclusion is that high levels of hopelessness and loneliness in adolescents are stable predictors of mental and emotional distress and psychosocial maladjustment in the period of psychological crises and decompensation of character accentuation of borderline and narcissistic types. These scales can be recommended for primary screening of antivital (depressive experiences and propensity to autoaggressive behavior in adolescents.

  20. Designing interactive technology for crowd experiences - beyond sanitization

    DEFF Research Database (Denmark)

    Veerasawmy, Rune

    2014-01-01

    experience within interaction design. This dissertation introduces an understanding of crowd experience as a distinct type of social experiences driven by non-rational behavior. This conceptual understanding is established in the intersection between sociological crowd theory and a pragmatist perspective...... sanitization. The domain of my experimental design inquiries is at sporting events. From extensive theoretical studies and my empirical explorations I present a perspective on modern and professionalized sporting events as sanitized, where the spectator experiences and technology are being produced, controlled......This dissertation concerns the topic on designing interactive technology for crowd expe- riences. It takes the outset in the experience-oriented design approach within interaction design, exploring the research question how can we conceptually understand and design interactive technology for crowd...

  1. Customer Relationship Management System in Occupational Safety & Health Companies: Research on Practice and Preliminary Design Solution

    Directory of Open Access Journals (Sweden)

    Robert Fabac

    2011-10-01

    Full Text Available One of the most prominent contemporary trends in formation of companies is the approach to development of a customer-oriented company. In this matter, various versions related to the intensity of this orientation are differentiated. Customer relationship management (CRM system is a well-known concept, and its practice is being studied and improved in connection to various sectors. Companies providing services of occupational safety and health (OHS mainly cooperate with a large number of customers and the quality of this cooperation largely affects the occupational safety and health of employees. Therefore, it is of both scientific and wider social interest to study and improve the relationship of these companies with their customers. This paper investigates the practice of applying CRM in Croatian OHS companies. It identifies the existing conditions and suggests possible improvements in the practice of CRM, based on experts’ assessments using analytic hierarchy process evaluation. Universal preliminary design was created as a framework concept for the formation of a typical customer-oriented OHS services company. Preliminary design includes a structural view, which provides more details through system diagrams, and an illustration of main cooperation processes of a company with its customer.

  2. Thermal Analysis of Iodine Satellite (iSAT) from Preliminary Design Review (PDR) to Critical Design Review (CDR)

    Science.gov (United States)

    Mauro, Stephanie

    2016-01-01

    The Iodine Satellite (iSAT) is a 12U cubesat with a primary mission to demonstrate the iodine fueled Hall Effect Thruster (HET) propulsion system. The spacecraft (SC) will operate throughout a one year mission in an effort to mature the propulsion system for use in future applications. The benefit of the HET is that it uses a propellant, iodine, which is easy to store and provides a high thrust-to-mass ratio. This paper will describe the thermal analysis and design of the SC between Preliminary Design Review (PDR) and Critical Design Review (CDR). The design of the satellite has undergone many changes due to a variety of challenges, both before PDR and during the time period discussed in this paper. Thermal challenges associated with the system include a high power density, small amounts of available radiative surface area, localized temperature requirements of the propulsion components, and unknown orbital parameters. The thermal control system is implemented to maintain component temperatures within their respective operational limits throughout the mission, while also maintaining propulsion components at the high temperatures needed to allow gaseous iodine propellant to flow. The design includes heaters, insulation, radiators, coatings, and thermal straps. Currently, the maximum temperatures for several components are near to their maximum operation limit, and the battery is close to its minimum operation limit. Mitigation strategies and planned work to solve these challenges will be discussed.

  3. Ocean thermal energy conversion cold water pipe preliminary design project. Task 2. Analysis for concept selection

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-04-01

    The successful performance of the CWP is of crucial importance to the overall OTEC system; the pipe itself is considered the most critical part of the entire operation. Because of the importance the CWP, a project for the analysis and design of CWP's was begun in the fall of 1978. The goals of this project were to study a variety of concepts for delivering cold water to an OTEC plant, to analyze and rank these concepts based on their relative cost and risk, and to develop preliminary design for those concepts which seemed most promising. Two representative platforms and sites were chosen: a spar buoy of a Gibbs and Cox design to be moored at a site off Punta Tuna, Puerto Rico, and a barge designed by APL/Johns Hopkins University, grazing about a site approximately 200 miles east of the coast of Brazil. The approach was to concentrate on the most promising concepts and on those which were either of general interest or espoused by others (e.g., steel and concrete concepts). Much of the overall attention, therefore, focused on analyzing rigid and compliant wall design, while stockade (except for the special case of the FRP stockade) and bottom-mounted concepts received less attention. A total of 67 CWP concepts were initially generated and subjected to a screening process. Of these, 16 were carried through design analysis, costing, and ranking. Study results are presented in detail. (WHK)

  4. Evolutionary experience design – the case of Otopia

    DEFF Research Database (Denmark)

    Hansen, Kenneth

    used as a means of specifying the basic immaterial design form. This discussion leads to the suggestion of a rule-based evolutionary model for the design of situations as a practical option for designers of new spectator oriented experiences in the future The project of Otopia was supported......The design of experiences is a complicated challenge. It might not even be possible to design such a “thing”, but only to design for it. If this is the case it could seem appropriate with an evolutionary approach. This paper introduces such an approach to the design of new public oriented...... experiences with the case of “Otopia”. “Otopia” is a large scale, new media experiment, which combines the areas of computer games, sports and performance in to a spectator oriented concept; it was premiered in a dome tent at the Roskilde Festival in Denmark the summer 2005. This paper presents and discusses...

  5. Modal identification experiment design for large space structures

    Science.gov (United States)

    Kim, Hyoung M.; Doiron, Harold H.

    1991-01-01

    This paper describes an on-orbit modal identification experiment design for large space structures. Space Station Freedom (SSF) systems design definition and structural dynamic models were used as representative large space structures for optimizing experiment design. Important structural modes of study models were selected to provide a guide for experiment design and used to assess the design performance. A pulsed random excitation technique using propulsion jets was developed to identify closely-spaced modes. A measuremenat location selection approach was developed to estimate accurate mode shapes as well as frequencies and damping factors. The data acquisition system and operational scenarios were designed to have minimal impacts on the SSF. A comprehensive simulation was conducted to assess the overall performance of the experiment design.

  6. Designing Learning Experiences for Deeper Understanding

    Science.gov (United States)

    Stripling, Barbara K.; Harada, Violet H.

    2012-01-01

    Planning is the less visible part of the teaching and learning process; however, it serves as the blueprint for student learning. To conceptualize the unit or project as a holistic learning experience, the authors created the C.L.E.A.R. G.O.A.L.S. guidelines that address the major elements of unit planning. An essential step is identifying the…

  7. Preliminary design of the beam screen cooling for the Future Circular Collider of hadron beams

    CERN Document Server

    Kotnig, C

    2015-01-01

    Following recommendations of the recent update of the European strategy in particle physics, CERN has undertaken an international study of possible future circular colliders beyond the LHC. This study considers an option for a very high energy (100 TeV) hadron-hadron collider located in a quasi-circular underground tunnel having a circumference of 80 to 100 km. The synchrotron radiation emitted by the high-energy hadron beam increases by more than two orders of magnitude compared to the LHC. To reduce the entropic load on the superconducting magnets' refrigeration system, beam screens are indispensable to extract the heat load at a higher temperature level. After illustrating the decisive constraints of the beam screen's refrigeration design, this paper presents a preliminary design of the length of a continuous cooling loop comparing helium and neon, for different cooling channel geometries with emphasis on the cooling length limitations and the exergetic efficiency.

  8. Preliminary design study of an alternate heat source assembly for a Brayton isotope power system

    Science.gov (United States)

    Strumpf, H. J.

    1978-01-01

    Results are presented for a study of the preliminary design of an alternate heat source assembly (HSA) intended for use in the Brayton isotope power system (BIPS). The BIPS converts thermal energy emitted by a radioactive heat source into electrical energy by means of a closed Brayton cycle. A heat source heat exchanger configuration was selected and optimized. The design consists of a 10 turn helically wound Hastelloy X tube. Thermal analyses were performed for various operating conditions to ensure that post impact containment shell (PICS) temperatures remain within specified limits. These limits are essentially satisfied for all modes of operation except for the emergency cooling system for which the PICS temperatures are too high. Neon was found to be the best choice for a fill gas for auxiliary cooling system operation. Low cycle fatigue life, natural frequency, and dynamic loading requirements can be met with minor modifications to the existing HSA.

  9. TPX: Contractor preliminary design review. Volume 5, Manufacturing R&D

    Energy Technology Data Exchange (ETDEWEB)

    Roach, J.F.; Urban, W.M.; Hartman, D. [Everson Electric Co., Bekthlehem, PA (United States)

    1995-08-04

    TPX Insulation & Impregnation R&D test results are reported for 1x2 samples designed for screening candidate conduit insulation systems for TPX PF and TF coils. The epoxy/glass insulation system and three proposed alternate insulation systems employing Kapton, was evaluated in as received sample condition and after 10 thermal cycles in liquid nitrogen. Two DGBA impregnation systems, Shell 826 and CTD101K were investigated. Square incoloy 908 and 316 LN stainless hollow conduits were used for 1x2 sample fabrication. Capacitance, dielectric loss, and insulation resistance dielectric characteristics were measured for all samples. Partial discharge performance was measured for samples either in air, under silicon oil, or under liquid nitrogen up to 10kVrms at 60 Hz. Hipot screening was performed at 10 kVdc. The samples were cross sectioned and evaluated for impregnation quality. The implications of the test results on the TPX preliminary design decision are discussed.

  10. Ocean Thermal Energy Conservation (OTEC) power system development (PDS) II. Preliminary design report

    Energy Technology Data Exchange (ETDEWEB)

    1979-08-10

    This report documents the results and conclusions of the PDS II, Phase I, preliminary design of a 10 MWe OTEC power system, using enhanced plate type heat exchangers, and of representative 0.2 MWe test articles. It further provides the documentation (specifications, drawings, trade studies, etc.) resulting from the design activities. The data and discussions of the technical concepts are organized to respond to the PDS II, Phase II proposal evaluation criteria. This volume, which specifically addresses the three evaluation categories (heat exchangers, rotating machinery, and power system configuration and performance) is an integral part of the Phase II plans (proposal) which describe the technical approach to delivering test articles to OTEC-1. In addition, there is a section which addresses power system cost and net energy analysis and another which discusses the results of stainless steel feasibility studies. Supporting documentation is contained in two appendix volumes.

  11. Interdisciplinary parametric design: the XXL experience

    NARCIS (Netherlands)

    Turrin, M.; Sariyildiz, I.S.; Paul, J.C.

    2015-01-01

    Focusing on large span structures for sport buildings, the paper tackles the role of parametric modelling and performance simulations, to enhance the integration between architectural and engineering design. The general approach contrasts post-engineering processes. In post-engineering, technical pe

  12. Carbon Pricing: Design, Experiences and Issues

    DEFF Research Database (Denmark)

    , which has negative implications for the future of our environment. In light of these negative developments, it is important to understand the benefits of environmental sustainability through well-documented research. This discerning book considers the design of carbon taxes and examines...

  13. Interdisciplinary parametric design: the XXL experience

    NARCIS (Netherlands)

    Turrin, M.; Sariyildiz, I.S.; Paul, J.C.

    2015-01-01

    Focusing on large span structures for sport buildings, the paper tackles the role of parametric modelling and performance simulations, to enhance the integration between architectural and engineering design. The general approach contrasts post-engineering processes. In post-engineering, technical

  14. The Role of Fiction in Experiments within Design, Art & Architecture

    DEFF Research Database (Denmark)

    Knutz, Eva; Markussen, Thomas; Christensen, Poul Rind

    2013-01-01

    This paper offers a typology for understanding design fiction as a new approach in design research. The typology allows design researchers to explain design fictions according to 5 criteria: (1) “What if scenarios” as the basic construal principle of design fiction; (2) the manifestation...... of critique; (3) design aims; (4) materializations and forms; and (5) the aesthetic of design fictions. The typology is premised on the idea that fiction may integrate with reality in many different ways in design experiments. The explanatory power of the typology is exemplified through the analyses of 6 case...

  15. Evolutionary experience design – the case of Otopia

    DEFF Research Database (Denmark)

    Hansen, Kenneth

    The design of experiences is a complicated challenge. It might not even be possible to design such a “thing”, but only to design for it. If this is the case it could seem appropriate with an evolutionary approach. This paper introduces such an approach to the design of new public oriented...... the overall development and design of the concept. First, the project is introduced and a model of the concept is outlined. Then the basic design objects are presented and a discussion of their various forms is initiated. Special attention is given here to the way the evolutionary design of rules has been...... used as a means of specifying the basic immaterial design form. This discussion leads to the suggestion of a rule-based evolutionary model for the design of situations as a practical option for designers of new spectator oriented experiences in the future The project of Otopia was supported...

  16. Experiences with Voice to Design Ceramics

    DEFF Research Database (Denmark)

    Hansen, Flemming Tvede; Jensen, Kristoffer

    2013-01-01

    This article presents SoundShaping, a system to create ceramics from the human voice and thus how digital technology makes new possibilities in ceramic craft. The article is about how experiential knowledge that the craftsmen gains in a direct physical and tactile interaction with a responding....... The shape is output to a 3D printer to make ceramic results. The system demonstrates the close connection between digital technology and craft practice. Several experiments and reflections demonstrate the validity of this work....

  17. Experiences with voice to design ceramics

    DEFF Research Database (Denmark)

    Hansen, Flemming Tvede; Jensen, Kristoffer

    2014-01-01

    This article presents SoundShaping, a system to create ceramics from the human voice and thus how digital technology makes new possibilities in ceramic craft. The article is about how experiential knowledge that the craftsmen gains in a direct physical and tactile interaction with a responding....... The shape is output to a 3D printer to make ceramic results. The system demonstrates the close connection between digital technology and craft practice. Several experiments and reflections demonstrate the validity of this work....

  18. Designing for user experiences in specific contexts: contributions from contextmapping

    NARCIS (Netherlands)

    Schifferstein, H.N.J.; Sleeswijk Visser, F.

    2013-01-01

    In saturated consumer markets, consumer choices often depend on subtle product differences that contribute positively to their user experiences. Hence, it is important for designers to be able to create products that elicit different experiences. In this chapter we discuss a design approach that tak

  19. Preliminary Design of a Modular Unmanned Research Vehicle. Volume 2. Subsystem Technical Development Design Study

    Science.gov (United States)

    1988-12-01

    for real-time analysis, or post-test aaalvsis innaediate;y foliowing the tesi , in a form that was iure easily interpreted. Because the test site will...in the baseline MURV design is the Teledyne 320. 11.6.2.4 Fuel Loading Trade Study With the propulsion system characteristics de- cided , the optimal

  20. The preliminary design of the optical Thomson scattering diagnostic for the National Ignition Facility

    Science.gov (United States)

    Datte, P.; Ross, J. S.; Froula, D.; Galbraith, J.; Glenzer, S.; Hatch, B.; Kilkenny, J.; Landen, O.; Manuel, A. M.; Molander, W.; Montgomery, D.; Moody, J.; Swadling, G.; Weaver, J.; Vergel de Dios, G.; Vitalich, M.

    2016-05-01

    The National Ignition Facility (NIF) is a 192 laser beam facility designed to support the Stockpile Stewardship, High Energy Density and Inertial Confinement Fusion programs. We report on the preliminary design of an Optical Thomson Scattering (OTS) diagnostic that has the potential to transform the community's understanding of NIF hohlraum physics by providing first principle, local, time-resolved measurements of under-dense plasma conditions. The system design allows operation with different probe laser wavelengths by manual selection of the appropriate beamsplitter and gratings before the shot. A deep-UV probe beam (λ0 between 185-215 nm) will optimally collect Thomson scattered light from plasma densities of 5 x 1020 electrons/cm3 while a 3ω probe will optimally collect Thomson scattered light from plasma densities of 1 x 1019 electrons/cm3. We report the phase I design of a two phase design strategy. Phase I includes the OTS recording system to measure background levels at NIF and phase II will include the integration of a probe laser.

  1. Preliminary design of a NIR prime focus corrector for the Galileo Telescope

    CERN Document Server

    Pernechele, C; Conconi, P; Gardiol, D; Molinari, E; Zerbi, F M; Pernechele, Claudio; Bortoletto, Favio; Conconi, Paolo; Gardiol, Daniele; Molinari, Emilio; Zerbi, Filippo

    2000-01-01

    In this paper a preliminary design for a prime focus corrector to be mounted at the Telescopio Nazionale Galileo (TNG) is presented. The telescope is located on La Palma (Canary Islands) and has a primary mirror of 3.5 m with a hyperbolic sag. Two optical designs have been considered in order to exploit detectors with 1k x 1k and 2k x 2k pixels. Each design makes use of four lenses, two of which are aspherical. The first lens diameters are, respectively, of 140 mm and 320 mm for the two kind of detectors. For both designs the telescope pupil is deliberately not re-imaged, and therefore it will not be possible to insert a cold stop. For such a reason particular care has been dedicated to the telescope thermal background study, in order to optimise the baffling system. The optics is able to correct fields of 11' x 11' and of 60'x60', depending on the design. It should be considered that the particular geometry of the focal plane array mosaic does not permit a full exploitation of the entire field, being based o...

  2. A Preliminary Theoretical Analysis of a Research Experience for Undergraduates Community Model

    Science.gov (United States)

    Castillo-Garsow, Carlos; Castillo-Chavez, Carlos; Woodley, Sherry

    2013-01-01

    The Mathematical and Theoretical Biology Institute (MTBI) is a successful summer research experience for undergraduates, with a strong record of mentoring Ph.D. graduates, particularly, underrepresented minority students. However, the MTBI program was designed for education in research, not for research in education, and the mechanisms of the…

  3. Preliminary experience with dexmedetomidine for monitored anesthesia care during ENT surgical procedures.

    Science.gov (United States)

    Busick, Tamra; Kussman, Mary; Scheidt, Troy; Tobias, Joseph D

    2008-01-01

    Dexmedetomidine is an alpha2-adrenergic agonist that produces anxiolysis, amnesia, sedation, potentiation of opioid analgesia, and sympatholysis. It is currently approved by the U.S. Food & Drug Administration for the sedation of adults in the intensive care setting for up to 24 hours during mechanical ventilation. Given its beneficial sedative and anxiolytic properties and limited adverse effect profile, it has been used in several other clinical scenarios. The authors present their experience using dexmedetomidine for monitored anesthesia care (MAC) during "awake" ENT procedures such as thyroplasty, a procedure requiring a patient to verbalize when requested but to otherwise remain immobile to allow for completion of the procedure, and in a patient with post-polio syndrome with poor pulmonary reserve requiring esophagoscopy with dilation and botulinum toxin injection for cricopharyngeal dysfunction. Our preliminary experience suggests that dexmedetomidine provides effective sedation as the primary agent for MAC during such procedures in adult patients. The end-organ effects of dexmedetomidine and previous reports of its use during MAC are reviewed.

  4. Preliminary experience with the MicroMed DeBakey pediatric ventricular assist device.

    Science.gov (United States)

    Fraser, Charles D; Carberry, Kathleen E; Owens, W Richard; Arrington, Karol A; Morales, David L S; Heinle, Jeffery S; McKenzie, E Dean

    2006-01-01

    Mechanical circulatory support for both acute and chronic heart failure is a widely applied therapeutic option in the adult population with a variety of devices clinically available. Technology in this field has advanced sufficiently such that long-term support or "destination therapy" has become a generally accepted reality. Similar progress has not occurred in the field of device support for heart failure in children. While the number of potential patients is significantly lower in the pediatric population, the clinical relevance and poignancy of individual need are nonetheless real. Until recently, children with heart failure have been largely disadvantaged in comparison to their adult counterparts. The DeBakey VAD Child (MicroMed Technology, Inc, Houston, TX) represents a hopeful initial step in the direction of reducing the technological gap between adults and children. While the clinical experience with this device is limited at present, preliminary results are encouraging. This report will provide an overview of the DeBakey VAD Child, including device specifications, indications for clinical use, surgical and postoperative considerations, and updated clinical experience.

  5. The DESI Experiment Part II: Instrument Design

    OpenAIRE

    DESI Collaboration; Aghamousa, Amir; Aguilar, Jessica; Ahlen, Steve; Alam, Shadab; Allen, Lori E.; Prieto, Carlos Allende; Annis, James; Bailey, Stephen; Balland, Christophe; Ballester, Otger; Baltay, Charles; Beaufore, Lucas; Bebek, Chris; Beers, Timothy C.

    2016-01-01

    DESI (Dark Energy Spectropic Instrument) is a Stage IV ground-based dark energy experiment that will study baryon acoustic oscillations and the growth of structure through redshift-space distortions with a wide-area galaxy and quasar redshift survey. The DESI instrument is a robotically-actuated, fiber-fed spectrograph capable of taking up to 5,000 simultaneous spectra over a wavelength range from 360 nm to 980 nm. The fibers feed ten three-arm spectrographs with resolution $R= \\lambda/\\Delta...

  6. Student designed experiments to learn fluids

    Science.gov (United States)

    Stern, Catalina

    2013-11-01

    Lasers and high speed cameras are a wonderful tool to visualize the very complex behavior of fluids, and to help students grasp concepts like turbulence, surface tension and vorticity. In this work we present experiments done by physics students in their senior year at the School of Science of the National University of Mexico as a final project in the continuum mechanics course. Every semester, the students make an oral presentation of their work and videos and images are kept in the web page ``Pasión por los Fluidos''. I acknowledge support from the Physics Department of Facultad de Ciencias, Universidad Nacional Autónoma de México.

  7. Relaying experiences for care home design

    DEFF Research Database (Denmark)

    Raudaskoski, Pirkko Liisa

    2014-01-01

    stakeholders (researchers, family members, etc.) could put forward their ideas and wishes about the facilities of a soon-to-be-built care home for people with brain injury. In other words, the seminar was part of a wider diagnostic endeavor that was to be started in a specially designed building. The future......The paper discusses organizational planning and decision making as situated material-semiotic practices in which various local and non-local meaningful elements (e.g. texts and photos) are invocated and resemiotized. The discussion is based on an analysis of a seminar meeting where different...

  8. Roles in Innovative Software Teams: A Design Experiment

    Science.gov (United States)

    Aaen, Ivan

    With inspiration from role-play and improvisational theater, we are developing a framework for innovation in software teams called Essence. Based on agile principles, Essence is designed for teams of developers and an onsite customer. This paper reports from teaching experiments inspired by design science, where we tried to assign differentiated roles to team members. The experiments provided valuable insights into the design of roles in Essence. These insights are used for redesigning how roles are described and conveyed in Essence.

  9. Simulation Data Management for Adaptive Design Of Experiment

    OpenAIRE

    BLONDET, Gaëtan; BOUDAOUD, Nassim; LE DUIGOU, Julien

    2015-01-01

    International audience; Recent evolutions of computer-aided product development and massive integration of numerical simulations to the design process require new methodologies to decrease the computational costs. Numerical design of experiments is used to increase quality of products by taking into account uncertainties in product development. But, this method can be time-consuming and involves a high computational cost. This paper presents a literature review of design of experiments method...

  10. Optimal Design of Experiments Subject to Correlated Errors

    OpenAIRE

    Pazman, Andrej; Müller, Werner

    2000-01-01

    In this paper we consider optimal design of experiments in the case of correlated observations, when no replications are possible. This situation is typical when observing a random process or random field with known covariance structure. We present a theorem which demonstrates that the computation of optimum exact designs corresponds to solving minimization problems in terms of design measures. (author's abstract)

  11. High risk cohort study for psychiatric disorders in childhood: rationale, design, methods and preliminary results.

    Science.gov (United States)

    Salum, Giovanni Abrahão; Gadelha, Ary; Pan, Pedro Mario; Moriyama, Tais Silveira; Graeff-Martins, Ana Soledade; Tamanaha, Ana Carina; Alvarenga, Pedro; Valle Krieger, Fernanda; Fleitlich-Bilyk, Bacy; Jackowski, Andrea; Sato, João Ricardo; Brietzke, Elisa; Polanczyk, Guilherme Vanoni; Brentani, Helena; de Jesus Mari, Jair; Do Rosário, Maria Conceição; Manfro, Gisele Gus; Bressan, Rodrigo Affonseca; Mercadante, Marcos Tomanik; Miguel, Eurípedes Constantino; Rohde, Luis Augusto

    2015-03-01

    The objective of this study is to present the rationale, methods, design and preliminary results from the High Risk Cohort Study for the Development of Childhood Psychiatric Disorders. We describe the sample selection and the components of each phases of the study, its instruments, tasks and procedures. Preliminary results are limited to the baseline phase and encompass: (i) the efficacy of the oversampling procedure used to increase the frequency of both child and family psychopathology; (ii) interrater reliability and (iii) the role of differential participation rate. A total of 9937 children from 57 schools participated in the screening procedures. From those 2512 (random = 958; high risk = 1554) were further evaluated with diagnostic instruments. The prevalence of any child mental disorder in the random strata and high-risk strata was 19.9% and 29.7%. The oversampling procedure was successful in selecting a sample with higher family rates of any mental disorders according to diagnostic instruments. Interrater reliability (kappa) for the main diagnostic instrument range from 0.72 (hyperkinetic disorders) to 0.84 (emotional disorders). The screening instrument was successful in selecting a sub-sample with "high risk" for developing mental disorders. This study may help advance the field of child psychiatry and ultimately provide useful clinical information.

  12. Design of a Microgravity Spray Cooling Experiment

    Science.gov (United States)

    Baysinger, Kerri M.; Yerkes, Kirk L.; Michalak, Travis E.; Harris, Richard J.; McQuillen, John

    2004-01-01

    An analytical and experimental study was conducted for the application of spray cooling in a microgravity and high-g environment. Experiments were carried out aboard the NASA KC-135 reduced gravity aircraft, which provided the microgravity and high-g environments. In reduced gravity, surface tension flow was observed around the spray nozzle, due to unconstrained liquid in the test chamber and flow reversal at the heat source. A transient analytical model was developed to predict the temperature and the spray heat transfer coefficient within the heated region. Comparison of the experimental transient temperature variation with analytical results showed good agreement for low heat input values. The transient analysis also verified that thermal equilibrium within the heated region could be reached during the 20-25s reduced gravity portion of the flight profile.

  13. On the design of closed recapture experiments.

    Science.gov (United States)

    Alunni Fegatelli, Danilo; Farcomeni, Alessio

    2016-11-01

    We propose a method to plan the number of occasions of recapture experiments for population size estimation. We do so by fixing the smallest number of capture occasions so that the expected length of the profile confidence interval is less than or equal to a fixed threshold. In some cases, we solve the optimization problem in closed form. For more complex models we use numerical optimization. We detail models assuming homogeneous, time-varying, subject-specific capture probabilities, behavioral response to capture, and combining behavioral response with subject-specific effects. The principle we propose can be extended to plan any other model specification. We formally show the validity of the approach by proving distributional convergence. We illustrate with simulations and challenging examples in epidemiology and ecology. We report that in many cases adding as few as two sampling occasions may substantially reduce the length of confidence intervals.

  14. Experiences with Voice to Design Ceramics

    DEFF Research Database (Denmark)

    Hansen, Flemming Tvede; Jensen, Kristoffer

    2013-01-01

    This article presents SoundShaping, a system to create ceramics from the human voice and thus how digital technology makes new possibilities in ceramic craft. The article is about how experiential knowledge that the craftsmen gains in a direct physical and tactile interaction with a responding ma....... The shape is output to a 3D printer to make ceramic results. The system demonstrates the close connection between digital technology and craft practice. Several experiments and reflections demonstrate the validity of this work....... material can be transformed and utilized in the use of digital technologies. SoundShaping is based on a generic audio feature extraction system and the principal component analysis to ensure that the pertinent information in the voice is used. Moreover, 3D shape is created using simple geometric rules...

  15. Preliminary designs for 25 kWe advanced Stirling conversion systems for dish electric applications

    Science.gov (United States)

    Shaltens, Richard K.; Schreiber, Jeffrey G.

    1990-01-01

    Under the Department of Energy's (DOE) Solar Thermal Technology Program, Sandia National Laboratories is evaluating heat engines for terrestrial Solar Distributed Heat Receivers. The Stirling engine has been identified by Sandia as one of the most promising engines for terrestrial applications. The Stirling engine also has the potential to meet DOE's performance and cost goals. The NASA Lewis Research Center is conducting Stirling engine technology development activities directed toward a dynamic power source for space applications. Space power systems requirements include high reliability, very long life, low vibration and high efficiency. The free-piston Stirling engine has the potential for future high power space conversion systems, either nuclear or solar powered. Although both applications appear to be quite different, their requirements complement each other. Preliminary designs feature a free-piston Stirling engine, a liquid metal heat transport system, and a means to provide nominally 25 kW electric power to a utility grid while meeting DOE's performance and long term cost goals. The Cummins design incorporates a linear alternator to provide the electrical output, while the STC design generates electrical power indirectly through a hydraulic pump/motor coupled to an induction generator. Both designs for the ASCS's will use technology which can reasonably be expected to be available in the early 1990's.

  16. Design and preliminary test of precision segment positioning actuator for the California Extremely Large Telescope

    Science.gov (United States)

    Lorell, Kenneth R.; Aubrun, Jean-Noel; Clappier, Robert R.; Shelef, Ben; Shelef, Gad

    2003-01-01

    In order for the California Extremely Large Telescope (CELT) to achieve the required optical performance, each of its 1000 primary mirror segments must be positioned relative to adjacent segments with nanometer-level accuracy. This can be accomplished using three actuators for each segment to actively control the segment in tip, tilt, and piston. The Keck telescopes utilize a segmented primary mirror similar to CELT employing a highly successful actuator design. However, because of its size and the shear number of actuators (3000 vs. 108 for Keck), CELT will require a different design. Sensitivity to wind loads and structural vibrations, the large dynamic range, low operating power, and extremely reliable operation, all achieved at an affordable unit cost, are the most demanding design requirements. This paper examines four actuator concepts and presents a trade-off between them. The concept that best met the CELT requirements is described along with an analysis of its performance. The concept is based on techniques that achieve the required accuracy while providing a substantial amount of vibration attenuation and damping. A prototype actuator has been built to validate this concept. Preliminary tests confirm predicted behavior and future tests will establish a sound baseline for final design and production.

  17. The ICE spectrograph for PEPSI at the LBT: preliminary optical design

    Science.gov (United States)

    Pallavicini, Roberto; Zerbi, Filippo M.; Spano, Paolo; Conconi, Paolo; Mazzoleni, Ruben; Molinari, Emilio; Strassmeier, Klaus G.

    2003-03-01

    We present a preliminary design study for a high-resolution echelle spectrograph (ICE) to be used with the spectropolarimeter PEPSI under development at the LBT. In order to meet the scientific requirements and take full advantage of the peculiarities of the LBT (i.e. the binocular nature and the adaptive optics capabilities), we have designed a fiber-fed bench mounted instrument for both high resolution (R ≍ 100,000; non-AO polarimetric and integral light modes) and ultra-high resolution (R ≍ 300,000; AO integral light mode). In both cases, 4 spectra per order (two for each primary mirror) shall be accomodated in a 2-dimensional cross dispersed echelle format. In order to obtain a resolution-slit product of ≍ 100,000 as required by the science case, we have considered two alternative designs, one with two R4 echelles in series and the other with a sigle R4 echelle and fiber slicing. A white-pupil design, VPH cross-dispersers and two cameras of different focal length for the AO and non-AO modes are adopted in both cases. It is concluded that the single-echelle fiber-slicer solution has to be preferred in terms of performances, complexity and cost. It can be implemented at the LBT in two phases, with the long-camera AO mode added in a second phase depending on the availability of funds and the time-scale for implementation of the AO system.

  18. Design of a Regenerative Life Support System for a Moon Base. Preliminary Results.

    Science.gov (United States)

    Duatis Juarez, Jordi; Guirado, Víctor; Lasseur, Christophe

    NTE-SENER has finalised a study under an ESA contract, to define a preliminary system design of an European Module to provide Environmental Control and Life Support to a potential Moon base. The design is based on current Life Support System technologies under development in Europe (MELiSSA, GWRU, Sabatier Reactor and UTU) along with contamination and microbial detection technologies (ANITA, MIDASS). The ECLSS is sized to provide water, air and up to the 40 As a support to the study a simulator has been developed to analyse the energy, volume and mass and the flow rates and efficiencies of the different components. The study applied the basics of the ALISSE criteria to evaluate the technologies taking as a source the results of the simulations. Detailed models of the different technologies have been developed including feedback from the pilot designs. The results of the study have showed up opportunities of improvement and many points that need to be further investigated. The technologies used in the study are based on the MELiSSA Pilot Plant reactors implementation and the results could affect their design in the near fu-ture in aspects such as carbon recycling, irrigation methods, energy consumption, technologies involved, etc.

  19. Preliminary Study on Kano Model in the Conceptual Design Activities for Product Lifecycle Improvement

    Science.gov (United States)

    Fahrul Hassan, Mohd; Rahman, M. R. A.; Arifin, A. M. T.; Ismail, A. E.; Rasidi Ibrahim, M.; Zulafif Rahim, M.; Fauzi Ahmad, Md

    2017-08-01

    Product manufactured with short life cycle had only one major issue, it can lead to increasing volume of waste. Day by day, this untreated waste had consumed many landfill spaces, waiting for any possible alternatives. Lack of product recovery knowledge and recyclability features imprinted into product design are one of the main reason behind all this. Sustainable awareness aspect should not just be implied into people’s mind, but also onto product design. This paper presents a preliminary study on Kano model method in the conceptual design activities to improve product lifecycle. Kano model is a survey-type method, used to analyze and distinguished product qualities or features, also how the customers may have perceived them. Three important attributes of Kano model are performance, attractive and must-be. The proposed approach enables better understanding of customer requirements while providing a way for Kano model to be integrated into engineering design to improve product’s end-of-life. Further works will be continued to provide a better lifecycle option (increase percentage of reuse, remanufacture or recycle, whereby decrease percentage of waste) of a product using Kano model approach.

  20. Preliminary Flight Results of the Microelectronics and Photonics Test Bed: NASA DR1773 Fiber Optic Data Bus Experiment

    Science.gov (United States)

    Jackson, George L.; LaBel, Kenneth A.; Marshall, Cheryl; Barth, Janet; Seidleck, Christina; Marshall, Paul

    1998-01-01

    NASA Goddard Spare Flight Center's (GSFC) Dual Rate 1773 (DR1773) Experiment on the Microelectronic and Photonic Test Bed (MPTB) has provided valuable information on the performance of the AS 1773 fiber optic data bus in the space radiation environment. Correlation of preliminary experiment data to ground based radiation test results show the AS 1773 bus is employable in future spacecraft applications requiring radiation tolerant communication links.

  1. Hypersonic Wind Tunnel Calibration Using the Modern Design of Experiments

    Science.gov (United States)

    Rhode, Matthew N.; DeLoach, Richard

    2005-01-01

    A calibration of a hypersonic wind tunnel has been conducted using formal experiment design techniques and response surface modeling. Data from a compact, highly efficient experiment was used to create a regression model of the pitot pressure as a function of the facility operating conditions as well as the longitudinal location within the test section. The new calibration utilized far fewer design points than prior experiments, but covered a wider range of the facility s operating envelope while revealing interactions between factors not captured in previous calibrations. A series of points chosen randomly within the design space was used to verify the accuracy of the response model. The development of the experiment design is discussed along with tactics used in the execution of the experiment to defend against systematic variation in the results. Trends in the data are illustrated, and comparisons are made to earlier findings.

  2. Design and Analysis of AN Static Aeroelastic Experiment

    Science.gov (United States)

    Hou, Ying-Yu; Yuan, Kai-Hua; Lv, Ji-Nan; Liu, Zi-Qiang

    2016-06-01

    Static aeroelastic experiments are very common in the United States and Russia. The objective of static aeroelastic experiments is to investigate deformation and loads of elastic structure in flow field. Generally speaking, prerequisite of this experiment is that the stiffness distribution of structure is known. This paper describes a method for designing experimental models, in the case where the stiffness distribution and boundary condition of a real aircraft are both uncertain. The stiffness distribution form of the structure can be calculated via finite element modeling and simulation calculation and F141 steels and rigid foam are used to make elastic model. In this paper, the design and manufacturing process of static aeroelastic models is presented and a set of experiment model was designed to simulate the stiffness of the designed wings, a set of experiments was designed to check the results. The test results show that the experimental method can effectively complete the design work of elastic model. This paper introduces the whole process of the static aeroelastic experiment, and the experimental results are analyzed. This paper developed a static aeroelasticity experiment technique and established an experiment model targeting at the swept wing of a certain kind of large aspect ratio aircraft.

  3. Central Equatorial Pacific Experiment (CEPEX). Design document

    Energy Technology Data Exchange (ETDEWEB)

    1993-04-01

    The Earth`s climate has varied significantly in the past, yet climate records reveal that in the tropics, sea surface temperatures seem to have been remarkably stable, varying by less than a few degrees Celsius over geologic time. Today, the large warm pool of the western Pacific shows similar characteristics. Its surface temperature always exceeds 27{degree}C, but never 31{degree}C. Heightened interest in this observation has been stimulated by questions of global climate change and the exploration of stabilizing climate feedback processes. Efforts to understand the observed weak sensitivity of tropical sea surface temperatures to climate forcing has led to a number of competing ideas about the nature of this apparent thermostat. Although there remains disagreement on the processes that regulate tropical sea surface temperature, most agree that further progress in resolving these differences requires comprehensive field observations of three-dimensional water vapor concentrations, solar and infrared radiative fluxes, surface fluxes of heat and water vapor, and cloud microphysical properties. This document describes the Central Equatorial Pacific Experiment (CEPEX) plan to collect such observations over the central equatorial Pacific Ocean during March of 1993.

  4. Microwave frequency sweep interferometer for plasma density measurements in ECR ion sources: Design and preliminary results

    Science.gov (United States)

    Torrisi, Giuseppe; Mascali, David; Neri, Lorenzo; Leonardi, Ornella; Sorbello, Gino; Celona, Luigi; Castro, Giuseppe; Agnello, Riccardo; Caruso, Antonio; Passarello, Santi; Longhitano, Alberto; Isernia, Tommaso; Gammino, Santo

    2016-02-01

    The Electron Cyclotron Resonance Ion Sources (ECRISs) development is strictly related to the availability of new diagnostic tools, as the existing ones are not adequate to such compact machines and to their plasma characteristics. Microwave interferometry is a non-invasive method for plasma diagnostics and represents the best candidate for plasma density measurement in hostile environment. Interferometry in ECRISs is a challenging task mainly due to their compact size. The typical density of ECR plasmas is in the range 1011-1013 cm-3 and it needs a probing beam wavelength of the order of few centimetres, comparable to the chamber radius. The paper describes the design of a microwave interferometer developed at the LNS-INFN laboratories based on the so-called "frequency sweep" method to filter out the multipath contribution in the detected signals. The measurement technique and the preliminary results (calibration) obtained during the experimental tests will be presented.

  5. Preliminary control system design and analysis for the Space Station Furnace Facility thermal control system

    Science.gov (United States)

    Jackson, M. E.

    1995-01-01

    This report presents the Space Station Furnace Facility (SSFF) thermal control system (TCS) preliminary control system design and analysis. The SSFF provides the necessary core systems to operate various materials processing furnaces. The TCS is defined as one of the core systems, and its function is to collect excess heat from furnaces and to provide precise cold temperature control of components and of certain furnace zones. Physical interconnection of parallel thermal control subsystems through a common pump implies the description of the TCS by coupled nonlinear differential equations in pressure and flow. This report formulates the system equations and develops the controllers that cause the interconnected subsystems to satisfy flow rate tracking requirements. Extensive digital simulation results are presented to show the flow rate tracking performance.

  6. Software tools and preliminary design of a control system for the 40m OAN radiotelescope

    Science.gov (United States)

    de Vicente, P.; Bolaño, R.

    2004-07-01

    The Observatorio Astronómico Nacional (OAN) is building a 40m radiotelescope in its facilities in Yebes (Spain) which will be delivered by April 2004. The servosystem will be controlled by an ACU (Antenna Control Unit), a real time computer running VxWorks which will be commanded from a remote computer (RCC) or from a local computer (LCC) which will act as console. We present the tools we have chosen to develop and use the control system for the RCC and the criteria followed for the choices we made. We also present a preliminary design of the control system on which we are currently working. The RCC will run a server which communicates with the ACU using sockets and with the clients, receivers and backends using OmniOrb, a free implementation of CORBA. Clients running Python will allow the users to control the antenna from any host connected to a LAN or a secure Internet connection.

  7. Microwave frequency sweep interferometer for plasma density measurements in ECR ion sources: Design and preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Torrisi, Giuseppe [INFN - Laboratori Nazionali del Sud, Via S. Sofia 62, 95125 Catania (Italy); University Mediterranea of Reggio Calabria, Reggio Calabria (Italy); Mascali, David; Neri, Lorenzo; Leonardi, Ornella; Celona, Luigi; Castro, Giuseppe; Agnello, Riccardo; Caruso, Antonio; Passarello, Santi; Longhitano, Alberto; Gammino, Santo [INFN - Laboratori Nazionali del Sud, Via S. Sofia 62, 95125 Catania (Italy); Sorbello, Gino [INFN - Laboratori Nazionali del Sud, Via S. Sofia 62, 95125 Catania (Italy); University of Catania, Catania, Italy and INFN-LNS, Catania (Italy); Isernia, Tommaso [University Mediterranea of Reggio Calabria, Reggio Calabria (Italy)

    2016-02-15

    The Electron Cyclotron Resonance Ion Sources (ECRISs) development is strictly related to the availability of new diagnostic tools, as the existing ones are not adequate to such compact machines and to their plasma characteristics. Microwave interferometry is a non-invasive method for plasma diagnostics and represents the best candidate for plasma density measurement in hostile environment. Interferometry in ECRISs is a challenging task mainly due to their compact size. The typical density of ECR plasmas is in the range 10{sup 11}–10{sup 13} cm{sup −3} and it needs a probing beam wavelength of the order of few centimetres, comparable to the chamber radius. The paper describes the design of a microwave interferometer developed at the LNS-INFN laboratories based on the so-called “frequency sweep” method to filter out the multipath contribution in the detected signals. The measurement technique and the preliminary results (calibration) obtained during the experimental tests will be presented.

  8. Cost-based optimization of a nuclear reactor core design: a preliminary model

    Energy Technology Data Exchange (ETDEWEB)

    Sacco, Wagner F.; Alves Filho, Hermes [Universidade do Estado do Rio de Janeiro (UERJ), Nova Friburgo, RJ (Brazil). Inst. Politecnico. Dept. de Modelagem Computacional]. E-mails: wfsacco@iprj.uerj.br; halves@iprj.uerj.br; Pereira, Claudio M.N.A. [Instituto de Engenharia Nuclear (IEN), Rio de Janeiro, RJ (Brazil). Div. de Reatores]. E-mail: cmnap@ien.gov.br

    2007-07-01

    A new formulation of a nuclear core design optimization problem is introduced in this article. Originally, the optimization problem consisted in adjusting several reactor cell parameters, such as dimensions, enrichment and materials, in order to minimize the radial power peaking factor in a three-enrichment zone reactor, considering restrictions on the average thermal flux, criticality and sub-moderation. Here, we address the same problem using the minimization of the fuel and cladding materials costs as the objective function, and the radial power peaking factor as an operational constraint. This cost-based optimization problem is attacked by two metaheuristics, the standard genetic algorithm (SGA), and a recently introduced Metropolis algorithm called the Particle Collision Algorithm (PCA). The two algorithms are submitted to the same computational effort and their results are compared. As the formulation presented is preliminary, more elaborate models are also discussed (author)

  9. Preliminary design review package for the solar heating and cooling central data processing system

    Energy Technology Data Exchange (ETDEWEB)

    1976-05-25

    This preliminary design review package, consisting of the Software Performance Specification, Hardware Performance Specification, and the Verification Plan for the Central Data Processing System (CDPS), was prepared by the IBM Corporation. The Central Data Processing System, located at IBM's FSD facility in Huntsville, Alabama, provides the resources required to assess the performance of solar heating and cooling systems at remote sites. These sites include residential, commercial, government, and educational types of buildings, and the solar heating and cooling systems can be hot water, space heating, cooling, and combinations of these. The instrumentation data associated with these systems will vary according to the application and must be collected, processed, and presented in a form which supports continuity of performance evaluation across all applications.

  10. Hybrid Spectral Micro-CT: System Design, Implementation, and Preliminary Results

    CERN Document Server

    Bennett, James R; Xu, Qiong; Yu, Hengyong; Walsh, Michael; Butler, Anthony; Butler, Phillip; Cao, Guohua; Mohs, Aaron; Wang, Ge

    2014-01-01

    Spectral CT has proven an important development in biomedical imaging, and there have been several publications in the past years demonstrating its merits in pre-clinical and clinical applications. In 2012, Xu et al. reported that near-term implementation of spectral micro-CT could be enhanced by a hybrid architecture: a narrow-beam spectral "interior" imaging chain integrated with a traditional wide-beam "global" imaging chain. This hybrid integration coupled with compressive sensing (CS)-based interior tomography demonstrated promising results for improved contrast resolution, and decreased system cost and radiation dose. The motivation for the current study is implementation and evaluation of the hybrid architecture with a first-of-its-kind hybrid spectral micro-CT system. Preliminary results confirm improvements in both contrast and spatial resolution. This technology is shown to merit further investigation and potential application in future spectral CT scanner design.

  11. PORFLOW MODELING FOR A PRELIMINARY ASSESSMENT OF THE PERFORMANCE OF NEW SALTSTONE DISPOSAL UNIT DESIGNS

    Energy Technology Data Exchange (ETDEWEB)

    Smith, F.

    2012-08-06

    At the request of Savannah River Remediation (SRR), SRNL has analyzed the expected performance obtained from using seven 32 million gallon Saltstone Disposal Units (SDUs) in the Z-Area Saltstone Disposal Facility (SDF) to store future saltstone grout. The analysis was based on preliminary SDU final design specifications. The analysis used PORFLOW modeling to calculate the release of 20 radionuclides from an SDU and transport of the radionuclides and daughters through the vadose zone. Results from this vadose zone analysis were combined with previously calculated releases from existing saltstone vaults and FDCs and a second PORFLOW model run to calculate aquifer transport to assessment points located along a boundary 100 m from the nearest edge of the SDF sources. Peak concentrations within 12 sectors spaced along the 100 m boundary were determined over a period of evaluation extending 20,000 years after SDF closure cap placement. These peak concentrations were provided to SRR to use as input for dose calculations.

  12. Index wiki database: design and experiments

    CERN Document Server

    Krizhanovsky, A A

    2008-01-01

    With the fantastic growth of Internet usage, information search in documents of a special type called a "wiki page" that is written using a simple markup language, has become an important problem. This paper describes the software architectural model for indexing wiki texts in three languages (Russian, English, and German) and the interaction between the software components (GATE, Lemmatizer, and Synarcher). The inverted file index database was designed using visual tool DBDesigner. The rules for parsing Wikipedia texts are illustrated by examples. Two index databases of Russian Wikipedia (RW) and Simple English Wikipedia (SEW) are built and compared. The size of RW is by order of magnitude higher than SEW (number of words, lexemes), though the growth rate of number of pages in SEW was found to be 12% higher than in Russian, and the rate of acquisition of new words in SEW lexicon was 6% higher during a period of five months (from September 2007 to February 2008). The Zipf's law was tested with both Russian an...

  13. Recent experience with design and manufacture of cine lenses

    Science.gov (United States)

    Thorpe, Michael D.; Dalzell, Kristen E.

    2015-09-01

    Modern cine lenses require a high degree of aberration correction over a large and ever expanding image size. At low to medium volume production levels, these highly corrected designs also require a workable tolerance set and compensation scheme for successful manufacture. In this paper we discuss the design and manufacture of cine lenses with reference to current designs both internal and in the patent literature and some experience in design, tolerancing and manufacturing these lenses in medium volume production.

  14. Preliminary Design and Simulation of a Turbo Expander for Small Rated Power Organic Rankine Cycle (ORC

    Directory of Open Access Journals (Sweden)

    Roberto Capata

    2014-11-01

    Full Text Available Nowadays, the Organic Rankine Cycle (ORC system, which operates with organic fluids, is one of the leading technologies for “waste energy recovery”. It works as a conventional Rankine Cycle but, as mentioned, instead of steam/water, an organic fluid is used. This change allows it to convert low temperature heat into electric energy where required. Large numbers of studies have been carried out to identify the most suitable fluids, system parameters and the various configurations. In the present market, most ORC systems are designed and manufactured for the recovery of thermal energy from various sources operating at “large power rating” (exhaust gas turbines, internal combustion engines, geothermal sources, large melting furnaces, biomass, solar, etc.; from which it is possible to produce a large amount of electric energy (30 kW ÷ 300 kW. Such applications for small nominal power sources, as well as the exhaust gases of internal combustion engines (car sedan or town, ships, etc. or small heat exchangers, are very limited. The few systems that have been designed and built for small scale applications, have, on the other hand, different types of expander (screw, scroll, etc.. These devices are not adapted for placement in small and restricted places like the interior of a conventional car. The aim of this work is to perform the preliminary design of a turbo-expander that meets diverse system requirements such as low pressure, small size and low mass flow rates. The expander must be adaptable to a small ORC system utilizing gas of a diesel engine or small gas turbine as thermal source to produce 2–10 kW of electricity. The temperature and pressure of the exhaust gases, in this case study (400–600 °C and a pressure of 2 bar, imposes a limit on the use of an organic fluid and on the net power that can be produced. In addition to water, fluids such as CO2, R134a and R245fa have been considered. Once the operating fluids has been chosen

  15. Utilization of Optimal Study Design for Maternal and Fetal Sheep Propofol Pharmacokinetics Study: A Preliminary Study

    Science.gov (United States)

    Sherwin, Catherine M. T.; Ngamprasertwong, Pornswan; Sadhasivam, Senthilkumar; Vinks, Alexander A.

    2017-01-01

    Multiple blood samples are generally required for measurement of pharmacokinetic (PK) parameters. D-optimal design is a popular and frequently used approach for determination of sampling time points in order to minimize the number of samples, while optimizing the estimation of PK parameters. Optimal design utilizing ADAPT (v5, BSR, University of Southern California, Los Angeles) developed a sparse sampling strategy to determine measurement of propofol in pregnant sheep. Propofal was administered as supplemental anesthetic agent to inhalation anesthesia to mimic anesthesia for open fetal surgery. In our preliminary study, propofol 3 mg/kg was given as a bolus to the ewe, followed by propofol infusion at rate 450 mcg/kg/min for 60 minutes, then decreased to 75 mcg/kg/min for 90 more minutes and then ceased. A three compartment model described the PK parameters with the fetus assumed as the third compartment. Initially, sampling times were chosen from thirteen time points as previously stated in the literature. Using priori propofol PK estimates, the final 9 sample time points were proposed in an optimal design with a change in infusion rate occurring between 65 and 75 minutes and sampling proposed at 5, 15, 25, 65, 75, 100, 110, 150, and 180 minutes. D-optimal design optimized the number and timing of samplings, which led to a reduction of cost and man power in the study protocol while preserving the ability to estimate propofol PK parameters in the maternal and fetal sheep model. Initial evaluation of samples collected from three sheep using the optimal design strategy confirmed the performance of the design in obtaining effective PK parameter estimates. PMID:24219004

  16. Medical chilling device designed for hypothermic hydration graft storage system: Design, thermohydrodynamic modeling, and preliminary testing

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Jung Hwan [Hongik University, Seoul (Korea, Republic of)

    2015-02-15

    Hypothermic hydration graft storage is essential to reduce the metabolic demand of cells in vitro. The alleviated metabolic demands reduce the emergence rate of anaerobic metabolism generating adenosine triphosphate (ATP) energy that creates free radicals. The cessive free radicals can damage cells and tissues due to their highly oxidative power with molecules. Current cooling systems such as a conventional air cooling system and an ice pack system are inappropriate for chilling cell tissues in vitro because of inconvenience in use and inconsistent temperature sustainability caused by large size and progressive melting, respectively. Here, we develop a medical chilling device (MCD) for hypothermic hydration graft storage based on thermo-hydrodynamic modeling and thermal electric cooling technology. Our analysis of obtained hydrodynamic thermal behavior of the MCD revealed that the hypothermic condition of 4 .deg. C was continuously maintained, which increased the survival rates of cells in vitro test by reduced free radicals. The validated performance of the MCD promises future development of an optimal hypothermic hydration graft storage system designed for clinical use.

  17. Prospectively gated axial CT coronary angiography: preliminary experiences with a novel low-dose technique

    Energy Technology Data Exchange (ETDEWEB)

    Klass, Oliver; Jeltsch, Martin; Feuerlein, Sebastian; Brunner, Horst; Brambs, Hans-Juergen; Hoffmann, Martin H.K. [University Hospital of Ulm, Department of Diagnostic and Interventional Radiology, Ulm (Germany); Nagel, Hans-Dieter [Philips Healthcare, Department of Science and Technology, Hamburg (Germany); Walker, Matthew J. [CT Clinical Science, Philips Healthcare, Cleveland, OH (United States)

    2009-04-15

    To assess image quality and radiation exposure with prospectively gated axial CT coronary angiography (PGA) compared to retrospectively gated helical techniques (RGH). Forty patients with suspected coronary artery disease (CAD) and a stable heart rate below 65 bpm underwent CT coronary angiography (CTCA) using a 64-channel CT system. The patient cohort consisted of 20 consecutive patients examined using a PGA technique and 20 patients examined using a standard RGH technique. Both groups were matched demographically according to age, gender, body mass index, and heart rate. For both groups, two independent observers assessed image quality for all coronary segments on an ordinal scale from 1 (nonassessable) to 5 (excellent quality). Image quality and radiation exposure were compared between patient groups. There were no significant differences in vessel-based image quality between the two groups (P > 0.05). Mean ({+-} SD) effective radiation exposure in the PGA group was 3.7 {+-} 0.8 mSv compared to 18.9 {+-} 3.8 mSv in the RGH group without ECG-based tube current modulation (P < 0.001). Preliminary experience shows PGA technique to be a promising approach for CTCA resulting in a substantial reduction in radiation exposure with image quality comparable to that of standard RGH technique. (orig.)

  18. Preliminary experience with drug-coated balloon angioplasty in primary percutaneous coronary intervention

    Institute of Scientific and Technical Information of China (English)

    Hee; Hwa; Ho; Julian; Tan; Yau; Wei; Ooi; Kwok; Kong; Loh; Than; Htike; Aung; Nwe; Tun; Yin; Dasdo; Antonius; Sinaga; Fahim; Haider; Jafary; Paul; Jau; Lueng; Ong

    2015-01-01

    We evaluated the clinical feasibility of using drugcoated balloon(DCB) angioplasty in patients undergoingprimary percutaneous coronary intervention(PPCI). Between January 2010 to September 2014,89 STelevation myocardial infarction patients(83% male,mean age 59 ± 14 years) with a total of 89 coronary lesions were treated with DCB during PPCI. Clinical outcomes are reported at 30 d follow-up. Left anterior descending artery was the most common target vessel for PCI(37%). Twenty-eight percent of the patients had underlying diabetes mellitus. Mean left ventricular ejection fraction was 44% ± 11%. DCB-only PCI was the predominant approach(96%) with the remaining 4% of patients receiving bail-out stenting. Thrombolysis in Myocardial Infarction(TIMI) 3 flow was successfully restored in 98% of patients. An average of 1.2 ± 0.5 DCB were used per patient,with mean DCB diameter of 2.6 ± 0.5 mm and average length of 23.2 ± 10.2 mm. At 30-d follow-up,there were 4 deaths(4.5%). No patients experienced abrupt closure of the infarctrelated artery and there was no reported target-lesion failure. Our preliminary experience showed that DCB angioplasty in PPCI was feasible and associated with a high rate of TIMI 3 flow and low 30-d ischaemic event.

  19. Pool film boiling experiments on a wire in low gravity: preliminary results.

    Science.gov (United States)

    Di Marco, P; Grassi, W; Trentavizi, F

    2002-10-01

    This paper reports preliminary results for pool film boiling on a wire immersed in almost saturated FC72 recently obtained during an experimental campaign performed in low gravity on the European Space Agency Zero-G airplane, (reduced gravity level 10(-2)). This is part of a long-term research program on the effect of gravitational and electric forces on boiling. The reported data set refers to experiments performed under the following conditions: (1) Earth gravity without electric field, (2) Earth gravity with electric field, (3) low gravity without electric field, and (4) low gravity with electric field. Although a decrease of gravity causes a heat transfer degradation, the electric field markedly improves heat exchange. This improvement is so effective that, beyond a certain field value, the heat flux is no longer sensitive to gravity. Two main film boiling regimes have been identified, both in normal and in low gravity: one is affected by the electric field and the other is practically insensitive to the field influence.

  20. Electromagnetic experiment to map in situ water in heated welded tuff: Preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez, A.L.; Daily, W.D.

    1987-03-16

    An experiment was conducted in Tunnel Complex G at the Nevada Test Site to evaluate geotomography as a possible candidate for in situ monitoring of hydrology in the near field of a heater placed in densely welded tuff. Alterant tomographs of 200 MHz electromagnetic permittivity were made for a vertical and a horizontal plane. After the 1 kilowatt heater was turned on, the tomographs indicated a rapid and strong drying adjacent to the heater. Moisture loss was not symmetric about the heater, but seemed to be strongly influenced by heterogeneity in the rock mass. The linear character of many tomographic features and their spatial correlation with fractures mapped in boreholes are evidence that drying was most rapid along some fractures. When the heater was turned off, an increase in moisture content occurred around the heater and along the dry fractures. However, this process is much slower and the magnitude of the moisture increase much smaller than the changes observed during heating of the rock. The interpretation of the tomographs is preliminary until they can be processed without the restrictive assumption of straight ray paths for the signals through the highly heterogeneous rock mass. 15 refs., 4 figs.

  1. Preliminary experience with laparoscopic repair of associated inguinal and umbilical hernias in children.

    Science.gov (United States)

    Bertozzi, M; Magrini, E; Appignani, A

    2015-08-01

    The authors report their preliminary experience in laparoscopic repair of associated inguinal and umbilical hernias in children. Twenty-six patients affected by the association of inguinal and umbilical hernia with an umbilical defect larger than 5 mm underwent a laparoscopic procedure. A 5-mm trocar was placed through the umbilical defect for the optic. To fix the trocar to avoid loss of carboperitoneum, we fashioned and tightened a purse-string non-absorbable suture with a sliding knot around the defect. In this manner, we ensured the trocar, fixing it and avoiding any loss of CO2, proceeding safely to the laparoscopic IH repair, by means of two additional 3 mm operative trocars. At the end of the inguinal herniorrhaphy, the previously fashioned purse-string suture was tightened to repair the umbilical defect. The mean operative time for the repair of associated inguinal and umbilical hernias was 30.1 ± 7.4 min in cases of unilateral inguinal hernia and 39.5 ± 10.6 for bilateral inguinal hernia. Follow-up ranged from 8 to 32 months. Neither intra- nor post-operative complications nor recurrences were seen. This small sample suggests that this simple method is safe, effective and might be useful for pediatric surgeons performing laparoscopic repair for inguinal hernia in presence of an associated UH with a statistically significant decrease of operative time.

  2. [The lived experience of family member caring for a person affected by Alzheimer's disease: preliminary results].

    Science.gov (United States)

    Vellone, E; Micci, F; Sansoni, J; Sinapi, N; Cattel, C

    2000-01-01

    The aim of this article is to report the preliminary results from a phenomenological study on the lived experience of Alzheimer's caregivers. Eight caregivers involved in caring for two years at list were interviewed. The analysis of interviews by Giorgi's method showed a multidimensional reality synthesizable in eight spheres of themes: Illness, Patient, Caring, Caregiver's Life and Health, Coping, Spouse/Family, Others, Feelings. Illness has a great impact on the caregivers' life and causes the loss of the affected person even before his/her death. Caring is very hard and emotionally involving. Caregivers mainly complain the lack of support from the National Health System. The continuous involvement in caring produces also health problems, depression, and negative effects within the family. Others are considered as bad. The most common feelings are fear for possible accidents to the patients and remorses. Some caregivers have good coping style putting their faith in God, valuing the closeness of the family and living daily. The utility of the eight spheres of themes are discussed in order to guide the practice toward the caregivers.

  3. Universal newborn hearing screening: preliminary experience at the University Hospital of Cagliari

    Directory of Open Access Journals (Sweden)

    Giulia Pinna

    2012-10-01

    Full Text Available Bilateral congenital or acquired sensorineural hearing loss is a pathological condition affecting 1-2 children per 1,000 live births; it represents a major issue in public health because its late identification can negatively affect speech and language development. The aim of hearing screening is to obtain diagnosis and management of hearing loss as soon as possible; in fact early diagnosis and treatment allow children with congenital hearing impairment to acquire adequate linguistic competence. The present study reports our preliminary experience in newborn hearing screening at Neonatology services of University of Cagliari (Italy. During the first semester of surveillance, between January 2012 and June 2012, hearing screening was performed on a total of 901 babies using two different methods, TEOAEs in healthy neonates and automated ABR in high-risk babies. All infants were screened prior to hospital discharge; in some cases, especially for preterm infants of Neonatal Intensive Care Unit and Puericulture Institute, the screening was performed after discharge, to achieve a possible better global and acoustic maturation; 5 cases of hearing impairment were found. In the present study the Authors confirmed that it is possible to start a universal hearing screening in a relatively short time reaching the percentages suggested by Joint Committee on Infant Hearing.

  4. Telescopio San Pedro Mártir Observatory preliminary design and project approach

    Science.gov (United States)

    Teran, Jose; Lee, William H.; Richer, Michael G.; Sánchez, Beatriz S.; Urdaibay, David; Hill, Derek; Adriaanse, David; Hernandez-Limonchi, Regina

    2016-07-01

    The Instituto de Astronomia of the Universidad Nacional Autónoma de México (UNAM) along with Instituto Nacional de Astrofisica, Optica y Electronica, the University of Arizona and the Smithsonian Astrophysical Observatory are developing the Telescopio San Pedro Mártir (TSPM) project, a 6.5m diameter optical telescope. M3 Engineering and Technology Corp. (M3) is the design and construction management firm responsible for all site infrastructure, enclosure and support facilities. The Telescopio San Pedro Mártir project (TSPM) will be located within the San Pedro Mártir National Park in Baja California, Mexico at 2,830 m. above sea level, approximately 65 km. east of the Pacific Ocean, 55km west of the Sea of Cortes (Gulf of California) and 180km south of the United States and México border. The aim of the paper is to present the preliminary design of the site infrastructure, enclosure and support facilities to date and share the design and construction approach.

  5. Preliminary design of the full-Stokes UV and visible spectropolarimeter for UVMag/Arago

    CERN Document Server

    Pertenais, Martin; Pares, Laurent; Petit, Pascal; Snik, Frans; van Harten, Gerard

    2015-01-01

    The UVMag consortium proposed the space mission project Arago to ESA at its M4 call. It is dedicated to the study of the dynamic 3D environment of stars and planets. This space mission will be equipped with a high-resolution spectropolarimeter working from 119 to 888 nm. A preliminary optical design of the whole instrument has been prepared and is presented here. The design consists of the telescope, the instrument itself, and the focusing optics. Considering not only the scienti?c requirements, but also the cost and size constraints to ?t a M-size mission, the telescope has a 1.3 m diameter primary mirror and is a classical Cassegrain-type telescope that allows a polarization-free focus. The polarimeter is placed at this Cassegrain focus. This is the key element of the mission and the most challenging to be designed. The main challenge lies in the huge spectral range offered by the instrument; the polarimeter has to deliver the full Stokes vector with a high precision from the FUV (119 nm) to the NIR (888 nm...

  6. Design and preliminary evaluation of an exoskeleton for upper limb resistance training

    Science.gov (United States)

    Wu, Tzong-Ming; Chen, Dar-Zen

    2012-06-01

    Resistance training is a popular form of exercise recommended by national health organizations, such as the American College of Sports Medicine (ACSM) and the American Heart Association (AHA). This form of training is available for most populations. A compact design of upper limb exoskeleton mechanism for homebased resistance training using a spring-loaded upper limb exoskeleton with a three degree-of-freedom shoulder joint and a one degree-of-freedom elbow joint allows a patient or a healthy individual to move the upper limb with multiple joints in different planes. It can continuously increase the resistance by adjusting the spring length to train additional muscle groups and reduce the number of potential injuries to upper limb joints caused by the mass moment of inertia of the training equipment. The aim of this research is to perform a preliminary evaluation of the designed function by adopting an appropriate motion analysis system and experimental design to verify our prototype of the exoskeleton and determine the optimal configuration of the spring-loaded upper limb exoskeleton.

  7. Design concept and preliminary experimental demonstration of MEMS gyroscopes with 4-DOF master-slave architecture

    Science.gov (United States)

    Acar, Cenk; Shkel, Andrei M.

    2002-07-01

    This paper reports a design concept for MEMS gyroscopes that shifts the complexity of the design from control architecture to system dynamics, utilizing the passive disturbance rejection capability of the 4-DOF dynamical system. Specifically, a novel wide-bandwidth micromachined gyroscope design approach based on increasing the degrees-of-freedom of the oscillatory system by the use of two independently oscillating interconnected proof masses is presented along with preliminary experimental demonstration of implementation feasibility. With the concept of using a 4-DOF system, inherent disturbance rejection is achieved due to the wide operation frequency range of the dynamic system, providing reduced sensitivity to structural and thermal parameter fluctuations. Thus, less demanding active control strategies are required for operation under presence of perturbations. The fabricated prototype dual-mass gyroscopes successfully demonstrated a dramatically wide driving frequency range within where the drive direction oscillation amplitude varies insignificantly without any active control, in contrast to the conventional gyroscopes where the mass has to be sustained in constant amplitude oscillation in a very narrow frequency band. Mechanical amplification of driven mass oscillation by the sensing element was also experimentally demonstrated, providing large oscillation amplitudes, which is crucial for sensor performance.

  8. Preliminary GN&C Design for the On-Orbit Autonomous Assembly of Nanosatellite Demonstration Mission

    Science.gov (United States)

    Pei, Jing; Walsh, Matt; Roithmayr, Carlos; Karlgaard, Chris; Peck, Mason; Murchison, Luke

    2017-01-01

    Small spacecraft autonomous rendezvous and docking (ARD) is an essential technology for future space structure assembly missions. The On-orbit Autonomous Assembly of Nanosatellites (OAAN) team at NASA Langley Research Center (LaRC) intends to demonstrate the technology to autonomously dock two nanosatellites to form an integrated system. The team has developed a novel magnetic capture and latching mechanism that allows for docking of two CubeSats without precise sensors and actuators. The proposed magnetic docking hardware not only provides the means to latch the CubeSats, but it also significantly increases the likelihood of successful docking in the presence of relative attitude and position errors. The simplicity of the design allows it to be implemented on many CubeSat rendezvous missions. Prior to demonstrating the docking subsystem capabilities on orbit, the GN&C subsystem should have a robust design such that it is capable of bringing the CubeSats from an arbitrary initial separation distance of as many as a few thousand kilometers down to a few meters. The main OAAN Mission can be separated into the following phases: 1) Launch, checkout, and drift, 2) Far-Field Rendezvous or Drift Recovery, 3) Proximity Operations, 4) Docking. This paper discusses the preliminary GN&C design and simulation results for each phase of the mission.

  9. Preliminary Safety Design Report for Remote Handled Low-Level Waste Disposal Facility

    Energy Technology Data Exchange (ETDEWEB)

    Timothy Solack; Carol Mason

    2012-03-01

    A new onsite, remote-handled low-level waste disposal facility has been identified as the highest ranked alternative for providing continued, uninterrupted remote-handled low-level waste disposal for remote-handled low-level waste from the Idaho National Laboratory and for nuclear fuel processing activities at the Naval Reactors Facility. Historically, this type of waste has been disposed of at the Radioactive Waste Management Complex. Disposal of remote-handled low-level waste in concrete disposal vaults at the Radioactive Waste Management Complex will continue until the facility is full or until it must be closed in preparation for final remediation of the Subsurface Disposal Area (approximately at the end of Fiscal Year 2017). This preliminary safety design report supports the design of a proposed onsite remote-handled low-level waste disposal facility by providing an initial nuclear facility hazard categorization, by discussing site characteristics that impact accident analysis, by providing the facility and process information necessary to support the hazard analysis, by identifying and evaluating potential hazards for processes associated with onsite handling and disposal of remote-handled low-level waste, and by discussing the need for safety features that will become part of the facility design.

  10. Wageningen Urban Rainfall Experiment 2014 (WURex14): Experimental setup and preliminary results

    Science.gov (United States)

    van Leth, Thomas C.; Uijlenhoet, Remko; Overeem, Aart; Leijnse, Hidde; Hazenberg, Pieter; Berne, Alexis

    2016-04-01

    Microwave links from cellular communication networks have been shown to be able to provide valuable information concerning the space-time variability of rainfall. In particular over urban areas, where network densities are generally high, they have the potential to complement existing dedicated infrastructure to measure rainfall (gauges, radars). In addition, microwave links provide a great opportunity for ground-based rainfall measurement for those land surface areas of the world where gauges and radars are generally lacking. Such information is not only crucial for water management and agriculture, but also for instance for ground validation of space-borne rainfall estimates such as those provided by the GPM (Global Precipitation Measurement) mission. WURex14 is dedicated to address several errors and uncertainties associated with such quantitative precipitation estimates in detail. The core of the experiment is provided by three co-located microwave links installed between two major buildings on the Wageningen University campus, approximately 2 km apart: a 38 GHz commercial microwave link, provided by T-Mobile NL, and 26 GHz and 38 GHz (dual-polarization) research microwave links from RAL. Transmitting and receiving antennas have been attached to masts installed on the roofs of the two buildings, about 30 m above the ground. This setup has been complemented with a Scintec infrared Large-Aperture Scintillometer, installed over the same path, as well as 5 Parsivel optical disdrometers and an automated rain gauge positioned at several locations along the path. Temporal sampling of the received signals was performed at a rate of 20 Hz. The setup is being monitored by time-lapse cameras to assess the state of the antennas as well as the atmosphere. Finally, data is available from the KNMI weather radars and an automated weather station situated just outside Wageningen. The experiment has been active between August 2014 and December 2015. We give a global overview of

  11. Preliminary optical design of PANIC, a wide-field infrared camera for CAHA

    Science.gov (United States)

    Cárdenas, M. C.; Rodríguez Gómez, J.; Lenzen, R.; Sánchez-Blanco, E.

    2008-07-01

    In this paper, we present the preliminary optical design of PANIC (PAnoramic Near Infrared camera for Calar Alto), a wide-field infrared imager for the Calar Alto 2.2 m telescope. The camera optical design is a folded single optical train that images the sky onto the focal plane with a plate scale of 0.45 arcsec per 18 μm pixel. A mosaic of four Hawaii 2RG of 2k x 2k made by Teledyne is used as detector and will give a field of view of 31.9 arcmin x 31.9 arcmin. This cryogenic instrument has been optimized for the Y, J, H and K bands. Special care has been taken in the selection of the standard IR materials used for the optics in order to maximize the instrument throughput and to include the z band. The main challenges of this design are: to produce a well defined internal pupil which allows reducing the thermal background by a cryogenic pupil stop; the correction of off-axis aberrations due to the large field available; the correction of chromatic aberration because of the wide spectral coverage; and the capability of introduction of narrow band filters (~1%) in the system minimizing the degradation in the filter passband without a collimated stage in the camera. We show the optomechanical error budget and compensation strategy that allows our as built design to met the performances from an optical point of view. Finally, we demonstrate the flexibility of the design showing the performances of PANIC at the CAHA 3.5m telescope.

  12. 2011 AERA Presidential Address: Designing Resilient Ecologies--Social Design Experiments and a New Social Imagination

    Science.gov (United States)

    Gutiérrez, Kris D.

    2016-01-01

    This article is about designing for educational possibilities--designs that in their inception, social organization, and implementation squarely address issues of cultural diversity, social inequality, and robust learning. I discuss an approach to design-based research, social design experiments, that privileges a social scientific inquiry…

  13. Kilowatt Reactor Using Stirling TechnologY (KRUSTY) Demonstration. CEDT Phase 1 Preliminary Design Documentation

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez, Rene Gerardo [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hutchinson, Jesson D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Mcclure, Patrick Ray [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Myers, William L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-08-20

    The intent of the integral experiment request IER 299 (called KiloPower by NASA) is to assemble and evaluate the operational performance of a compact reactor configuration that closely resembles the flight unit to be used by NASA to execute a deep space exploration mission. The reactor design will include heat pipes coupled to Stirling engines to demonstrate how one can generate electricity when extracting energy from a “nuclear generated” heat source. This series of experiments is a larger scale follow up to the DUFF series of experiments1,2 that were performed using the Flat-Top assembly.

  14. Selecting the best design for nonstandard toxicology experiments.

    Science.gov (United States)

    Webb, Jennifer M; Smucker, Byran J; Bailer, A John

    2014-10-01

    Although many experiments in environmental toxicology use standard statistical experimental designs, there are situations that arise where no such standard design is natural or applicable because of logistical constraints. For example, the layout of a laboratory may suggest that each shelf serve as a block, with the number of experimental units per shelf either greater than or less than the number of treatments in a way that precludes the use of a typical block design. In such cases, an effective and powerful alternative is to employ optimal experimental design principles, a strategy that produces designs with precise statistical estimates. Here, a D-optimal design was generated for an experiment in environmental toxicology that has 2 factors, 16 treatments, and constraints similar to those described above. After initial consideration of a randomized complete block design and an intuitive cyclic design, it was decided to compare a D-optimal design and a slightly more complicated version of the cyclic design. Simulations were conducted generating random responses under a variety of scenarios that reflect conditions motivated by a similar toxicology study, and the designs were evaluated via D-efficiency as well as by a power analysis. The cyclic design performed well compared to the D-optimal design.

  15. Optimal experiment design for identification of grey-box models

    DEFF Research Database (Denmark)

    Sadegh, Payman; Melgaard, Henrik; Madsen, Henrik

    1994-01-01

    Optimal experiment design is investigated for stochastic dynamic systems where the prior partial information about the system is given as a probability distribution function in the system parameters. The concept of information is related to entropy reduction in the system through Lindley's measure...... estimation results in a considerable reduction of the experimental length. Besides, it is established that the physical knowledge of the system enables us to design experiments, with the goal of maximizing information about the physical parameters of interest....

  16. Assay optimization: a statistical design of experiments approach.

    Science.gov (United States)

    Altekar, Maneesha; Homon, Carol A; Kashem, Mohammed A; Mason, Steven W; Nelson, Richard M; Patnaude, Lori A; Yingling, Jeffrey; Taylor, Paul B

    2007-03-01

    With the transition from manual to robotic HTS in the last several years, assay optimization has become a significant bottleneck. Recent advances in robotic liquid handling have made it feasible to reduce assay optimization timelines with the application of statistically designed experiments. When implemented, they can efficiently optimize assays by rapidly identifying significant factors, complex interactions, and nonlinear responses. This article focuses on the use of statistically designed experiments in assay optimization.

  17. Food Enterprise Web Design Based on User Experience

    OpenAIRE

    Fei Wang

    2015-01-01

    Excellent auxiliary food enterprise web design conveyed good visual transmission effect through user experience. This study was based on the food enterprise managers and customers as the main operating object to get the performance of the web page creation, web page design not only focused on the function and work efficiency, the most important thing was that the user experience in the process of web page interaction.

  18. Ocean thermal energy conversion power system development-I. Phase I. Preliminary design report. Volume 1. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-18

    The results of a conceptual and preliminary design study of Ocean Thermal Energy Conversion (OTEC) closed loop ammonia power system modules performed by Lockheed Missiles and Space Company, Inc. (LMSC) are presented. This design study is the second of 3 tasks in Phase I of the Power System Development-I Project. The Task 2 objectives were to develop: 1) conceptual designs for a 40 to 50-MW(e) closed cycle ammonia commercial plant size power module whose heat exchangers are immersed in seawater and whose ancillary equipments are in a shirt sleeve environment; preliminary designs for a modular application power system sized at 10-MW(e) whose design, construction and material selection is analogous to the 50 MW(e) module, except that titanium tubes are to be used in the heat exchangers; and 3) preliminary designs for heat exchanger test articles (evaporator and condenser) representative of the 50-MW(e) heat exchangers using aluminum alloy, suitable for seawater service, for testing on OTEC-1. The reference ocean platform was specified by DOE as a surface vessel with the heat exchanger immersed in seawater to a design depth of 0 to 20 ft measured from the top of the heat exchanger. For the 50-MW(e) module, the OTEC 400-MW(e) Plant Ship, defined in the Platform Configuration and Integration study, was used as the reference platform. System design, performance, and cost are presented. (WHK)

  19. CT-guided thin needles percutaneous cryoablation (PCA) in patients with primary and secondary lung tumors: A preliminary experience

    Energy Technology Data Exchange (ETDEWEB)

    Pusceddu, Claudio, E-mail: clapusceddu@gmail.com [Division of Interventional Radiology, Department of Oncological Radiology, Businco Hospital, Regional Referral Center for Oncologic Diseases, Cagliari, Zip code 09100 (Italy); Sotgia, Barbara, E-mail: barbara.sotgia@gmail.com [Department of Oncological Radiology, Businco Hospital, Regional Referral Center for Oncological Diseases, Cagliari, Zip code 09100 (Italy); Fele, Rosa Maria, E-mail: rosellafele@tiscali.it [Department of Oncological Radiology, Businco Hospital, Regional Referral Center for Oncological Diseases, Cagliari, Zip code 09100 (Italy); Melis, Luca, E-mail: doclucamelis@tiscali.it [Department of Oncological Radiology, Businco Hospital, Regional Referral Center for Oncological Diseases, Cagliari, Zip code 09100 (Italy)

    2013-05-15

    Purpose: To report the data of our initial experience with CT-guided thin cryoprobes for percutaneous cryoablation (PCA) in patients with primary and secondary pulmonary tumors. Material and methods: CT-guided thin needles PCA was performed on 34 lung masses (11 NSCLC = 32%; 23 secondary lung malignancies = 68%) in 32 consecutive patients (24 men and 8 women; mean age 67 ± 10 years) not suitable for surgical resection. Lung masses were treated using two types of cryoprobes: IceRod and IceSeed able to obtain different size of iceball. The number of probes used ranged from 1 to 5 depending on the size of the tumor. After insertion of the cryoprobes into the lesion, the PCA were performed with two 2 (91%) or 3 (9%) cycles each of 12 min of freezing followed by a 4 min active thawing phase and a 4 min passive thawing phase for each one for all treatments. Results: All cryoablation sessions were successfully completed. All primary and metastatic lung tumors were ablated. No procedure-related deaths occurred. Morbidity consisted of 21% (7 of 34) pneumothorax and 3% (1 of 34) cases asymptomatic small pulmonary hemorrhage, respectively, all of CTCAE grade 1 (Common Terminology Criteria for Adverse Events). Low density of entire lesion, central necrosis and solid mass appearance were identify in 21 (62%), 7 (21%) and 6 (17%) of cryoablated tumors, respectively. No lymphadenopathy developed in the region of treated lesions. Technical success (complete lack of enhancement) was achieved in 82%, 97% and 91% of treated lesions at 1-, 3- and 6-months CT follow-up scan, respectively (p < .000). Comparing the tumor longest diameter between the baseline and at 6 month CT images, technical success was revealed in 92% cases (p < .000). Conclusion: Our preliminary experience suggests that PCA is a feasible treatment option. Well-designed clinical trials with a larger patient population are necessary to further investigate the long-term results and prognostic factors.

  20. A Model for Designing Adaptive Laboratory Evolution Experiments.

    Science.gov (United States)

    LaCroix, Ryan A; Palsson, Bernhard O; Feist, Adam M

    2017-04-15

    The occurrence of mutations is a cornerstone of the evolutionary theory of adaptation, capitalizing on the rare chance that a mutation confers a fitness benefit. Natural selection is increasingly being leveraged in laboratory settings for industrial and basic science applications. Despite increasing deployment, there are no standardized procedures available for designing and performing adaptive laboratory evolution (ALE) experiments. Thus, there is a need to optimize the experimental design, specifically for determining when to consider an experiment complete and for balancing outcomes with available resources (i.e., laboratory supplies, personnel, and time). To design and to better understand ALE experiments, a simulator, ALEsim, was developed, validated, and applied to the optimization of ALE experiments. The effects of various passage sizes were experimentally determined and subsequently evaluated with ALEsim, to explain differences in experimental outcomes. Furthermore, a beneficial mutation rate of 10(-6.9) to 10(-8.4) mutations per cell division was derived. A retrospective analysis of ALE experiments revealed that passage sizes typically employed in serial passage batch culture ALE experiments led to inefficient production and fixation of beneficial mutations. ALEsim and the results described here will aid in the design of ALE experiments to fit the exact needs of a project while taking into account the resources required and will lower the barriers to entry for this experimental technique.IMPORTANCE ALE is a widely used scientific technique to increase scientific understanding, as well as to create industrially relevant organisms. The manner in which ALE experiments are conducted is highly manual and uniform, with little optimization for efficiency. Such inefficiencies result in suboptimal experiments that can take multiple months to complete. With the availability of automation and computer simulations, we can now perform these experiments in an optimized