EDUCATING FOR QUALITY IN THE WOOD INDUSTRY: SOME WORDS OF CAUTION

Directory of Open Access Journals (Sweden)

Sydney Engelberg

2016-03-01

Full Text Available The problem of over enthusiastically adopting paradigms and models is well known in science in general, and in management in particular. The current trend of presenting "quality" in an unfailingly positive light in manufacturing, including in the wood industry, echoes this problem. This results in those aspects of "quality enhancement" that reflect negative processes and emotions being neglected, receiving lip service attention, or in subtle ways being denigrated. This is, potentially, the source of a severe limitation in the understanding and implementation of quality enhancement programs in the wood industry. Good intentions are insufficient. We cannot continue to neglect such issues as: authority and control; caution and reserve; autonomy and separateness; competition and aggressiveness; dislike and resistance; exploitation and manipulation; and self-interest, if we wish education for quality to be successful.

Thermophotovoltaics, wood powder and fuel quality

Energy Technology Data Exchange (ETDEWEB)

Marks, J [Swedish Univ. of Agricultural Sciences, Uppsala (Sweden). Dept. of Operational Efficiency; Broman, L; Jarefors, K [Solar Energy Research Center, Borlaenge (Sweden)

1998-06-01

PV cells can be used for electricity production based on other heat sources than the sun. If the temperature of the source is around 1500 K it is possible to get reasonably high conversion efficiency from heat radiation to electricity. This is due to recent advances in low-bandgap PV cells and selectively emitting fibrous emissive burners. There are some different biomass fuels capable of producing this temperature in the flame, especially gas and liquid fuels of different kinds. Wood powder is the only solid wood fuel with a sufficiently stable quality and properties for this high temperature combustion. A joint project between SERC, SLU and National Renewable Energy Laboratory NREL in Golden, Colorado, USA aims at building a wood powder fuelled thermophotovoltaic (TPV) generator for cogeneration of heat and electricity. A stable flame temperature of 1500 K has been achieved in a prototype pilot-scale burner that includes feeder and combustion chamber. Furthermore, a setup for measuring TPV cell efficiency for a wide region of black body emitter temperatures and cell irradiation has been constructed and several 0.6 eV GaInAs TPV cells have been investigated. A setup for testing the chain IR emitter - selectively reflecting filter - TPV cell has been designed. In order to limit the region of filter incident angles, which will make the filter act more efficiently, a special geometry of the internally reflecting tube that transmits the radiation is considered 23 refs, 4 figs

Impact of operating wood-burning fireplace ovens on indoor air quality.

Science.gov (United States)

Salthammer, Tunga; Schripp, Tobias; Wientzek, Sebastian; Wensing, Michael

2014-05-01

The use of combustion heat sources like wood-burning fireplaces has regained popularity in the past years due to increasing energy costs. While the outdoor emissions from wood ovens are strictly regulated in Germany, the indoor release of combustion products is rarely considered. Seven wood burning fireplaces were tested in private homes between November 2012 and March 2013. The indoor air quality was monitored before, during and after operation. The following parameters were measured: ultra-fine particles (5.6-560 nm), fine particles (0.3-20 μm), PM2.5, NOx, CO, CO2, formaldehyde, acetaldehyde, volatile organic compounds (VOCs) and benzo[a]pyrene (BaP). Most ovens were significant sources of particulate matter. In some cases, an increase of benzene and BaP concentrations was observed in the indoor air. The results illustrate that wood-burning fireplaces are potential sources of indoor air contaminants, especially ultra-fine particles. Under the aspect of lowering indoor air exchange rates and increasing the use of fuels with a net zero-carbon footprint, indoor combustion sources are an important topic for the future. With regards to consumer safety, product development and inspection should consider indoor air quality in addition to the present fire protection requirements. Copyright © 2013 Elsevier Ltd. All rights reserved.

Quality wood chips - an alternative to pellets; Alternative zu Pellets. Qualischnitzel

Energy Technology Data Exchange (ETDEWEB)

Keel, A.

2008-07-01

This article takes a look at a new wood-chip product that features wood-chips that are dryer than traditional ones. The new 'quality chips' are also of a calibrated size and are supplied dust-free. Their low water content permits their use in the same areas as wood pellets, where, especially in summer, low water-content is important. The increasing use of pellets and the growing shortages of clean sawdust and shavings for their production is commented on, as is the use of forestry wastes in pellet production. The new wood-chip product is further discussed as being a direct alternative to pellets. The low 'grey energy' content for tree-felling, hacking, transport and the drying of the chips is quoted as being less than 5% of the energy in the chippings.

Wood adhesives : vital for producing most wood products

Science.gov (United States)

Charles R. Frihart

2011-01-01

A main route for the efficient utilization of wood resources is to reduce wood to small pieces and then bond them together (Frihart and Hunt 2010). Although humankind has been bonding wood since early Egyptian civilizations, the quality and quantity of bonded wood products has increased dramatically over the past 100 years with the development of new adhesives and...

Designing Wood Supply Scenarios from Forest Inventories with Stratified Predictions

Directory of Open Access Journals (Sweden)

Philipp Kilham

2018-02-01

Full Text Available Forest growth and wood supply projections are increasingly used to estimate the future availability of woody biomass and the correlated effects on forests and climate. This research parameterizes an inventory-based business-as-usual wood supply scenario, with a focus on southwest Germany and the period 2002–2012 with a stratified prediction. First, the Classification and Regression Trees algorithm groups the inventory plots into strata with corresponding harvest probabilities. Second, Random Forest algorithms generate individual harvest probabilities for the plots of each stratum. Third, the plots with the highest individual probabilities are selected as harvested until the harvest probability of the stratum is fulfilled. Fourth, the harvested volume of these plots is predicted with a linear regression model trained on harvested plots only. To illustrate the pros and cons of this method, it is compared to a direct harvested volume prediction with linear regression, and a combination of logistic regression and linear regression. Direct harvested volume regression predicts comparable volume figures, but generates these volumes in a way that differs from business-as-usual. The logistic model achieves higher overall classification accuracies, but results in underestimations or overestimations of harvest shares for several subsets of the data. The stratified prediction method balances this shortcoming, and can be of general use for forest growth and timber supply projections from large-scale forest inventories.

Impact of operating wood-burning stoves on indoor air quality

DEFF Research Database (Denmark)

Afshari, Alireza; Jensen, Ole Michael; Bergsøe, Niels Christian

2011-01-01

A field study on the impact of operating and reloading wood-burning stoves on the indoor air quality was carried out during two consecutive winters. In contrast to the majority of recent studies, which focussed on the ambient air quality and the penetration of particles to the indoor air......, this study aims to understand to what extent the operation of a stove contributes to the generation of concentration of ultrafine particles in the indoor air. Therefore, different stoves were ignited in one session by the owner of the stove and in a subsequent session by an expert on wood-burning stoves....... The study was conducted in seven typical Danish detached houses without other indoor activities taking place. In each house the average air change rate during one week was measured (using passive tracer gas technique) and the indoor and outdoor temperature and relative humidity were recorded continuously...

Soil quality in a cropland soil treated with wood ash containing charcoal

Science.gov (United States)

Omil, Beatriz; Balboa, Miguel A.; Fonturbel, M. Teresa; Gartzia-Bengoetxea, Nahia; Arias-González, Ander; Vega, Jose A.; Merino, Agustin

2014-05-01

The strategy of the European Union "Europe 2020" states that by 2020, 20% of final energy consumption must come from renewables. In this scenario, there is an increasing use of biomass utilization for energy production. Indeed, it is expected that the production of wood-ash will increase in coming years. Wood ash, a mixture of ash and charcoal, generated as a by-product of biomass combustion in power plants, can be applied to soil to improve the soil quality and crop production. Since the residue contains significant content of charcoal, the application of mixed wood ash may also improve the SOM content and soil quality in the long term, in soils degraded as a consequence of intensive management. The objective of this study was asses the changes in SOM quality and soil properties in a degraded soils treated with wood ash containing charcoal. The study was carried out in a field devoted to cereal crops during the last decades. The soil was acidic (pH 4.5) with a low SOC content (3 %) and fine texture. The experiment was based on a randomised block design with four replicates. Each block included the following four treatments: Control, 16 Mg fly wood ash ha-1, 16 Mg mixed wood ash ha-1 (16 Mg) and 32 Mg mixed wood ash ha-1 (32 Mg). The application was carried out once. The ash used in the study was obtained from a thermal power plant and was mainly derived from the combustion of Pinus radiata bark and branches. The wood ash is highly alkaline (pH= 10), contains 10 % of highly condensed black carbon (atomic H/C ratio solid state 13C CPMAS NMR and Differential Scanning Calorimetry (DSC). These techniques were applied in bulk samples and aggregates of different sizes. The changes in microbial activity were studied by analysis of microbial biomass C and basal respiration. The soil bacterial community was studied by the Biolog method. Several physical properties, such soil aggregate distribution, hydraulic conductivity and available water contente were also determined

On the influence of crack closure on strength estimates of wood

DEFF Research Database (Denmark)

Nielsen, Lauge Fuglsang

2004-01-01

Three well-known duration of load models (Gerhard, Barrett/Foschi, DVM) are considered in this note with respect to their ability to predict lifetime of wood subjected to harmonically varying loads. The result obtained is that they practically predict the same lifetime—which for low frequency...... in metals).It is suggested that any of the simple models can be used in practice when low frequency load variations are considered. The DVM model, however, should be preferred because of its ability to predict residual strength, and because of its ‘build in’ flexibility with respect to wood quality...

Quality Measurement in the Wood Products Supply Chain

OpenAIRE

Espinoza, Omar Alejandro

2009-01-01

The purpose of this research is to learn about quality measurement practices in a wood products supply chain. According to the Supply Chain Management paradigm, companies no longer compete as individual entities, but as part of complex networks of suppliers and customers, linked together by flows of materials and information. Evidence suggests that a high degree of integration between supply chain members is essential to achieve superior market and financial performance. This study investigat...

The wood quality of the South African timber resource for high-value ...

African Journals Online (AJOL)

However, the forest industry's future success will also be judged on how well it understands the qualities of the timber supply, how successful it is with the implementation of appropriate wood quality improvement strategies and how willing it is to introduce new species and hybrids which are unique and different from the ...

Wood versus quality of the air?

International Nuclear Information System (INIS)

Richard, A.

2015-01-01

CITEPA has estimated at 875000 tonnes the releases of fine particles in France in 2014. Wood heating is responsible for 1/3 of the release of PM10 particles (particles with a diameter lower than 10 μm) and for half of the release of PM2.5 particles. PM2.5 particles are particles whose diameter is lower than 2.5 μm, they are more dangerous than PM10 particles because they enter the lungs more deeply. In 2012 the World Health Organisation acknowledged fine particles as responsible for lung cancers. The other contributors are industry (20 to 30%) and transport (16%). The uncertainties on the figures are important and can reach 50% as the estimations are based on extrapolations but wood heating appears to be the major polluter. The solution is to promote the installation of new wood heating systems that release far less particles. Open fireplaces and closed fireplaces installed before 2002 release respectively 97 and 91 kg of fine particles a year while closed fireplaces installed after 2007 release only 8 kg a year and the latest closed systems only 3 kg a year. In some mountainous regions like Haute-Savoie where wood heating is a tradition, local authorities give financial helps to individuals to install efficient systems. Community wood heating and industrial wood boilers have been equipped with efficient filters since the first Grenelle law on the environment took effect and their releases of fine particles have dropped sharply. (A.C.)

Wood Quality of Acacia Hybrid and Second-Generation Acacia mangium

Directory of Open Access Journals (Sweden)

Ismail Jusoh

2013-11-01

Full Text Available Two new tree variants, namely Acacia hybrid and second-generation Acacia mangium, have been introduced in plantation forests in Sarawak, Malaysia, and their wood qualities were examined. The mean basic density of Acacia hybrid was comparable with Acacia mangium. However basic density and strength properties of second-generation A. mangium were significantly lower compared to Acacia hybrid. The mean fibre length and fibre wall thickness in the hybrid were found to be greater than that of second-generation A. mangium. Fibre diameter and fibre lumen diameter of Acacia hybrid were smaller compared to second-generation A. mangium. Runkel and slenderness ratios of Acacia hybrid and second-generation A. mangium fibres showed that they were suitable for pulp and paper production. Acacia hybrid was more resistant to Coptotermes curvignathus attack than second-generation A. mangium. A laboratory soil block test showed that Acacia hybrid and second-generation A. mangium were moderately durable timbers. In summary, marked differences in wood properties and qualities were observed between Acacia hybrid and second-generation A. mangium.

Kinetic model for torrefaction of wood chips in a pilot-scale continuous reactor

DEFF Research Database (Denmark)

Shang, Lei; Ahrenfeldt, Jesper; Holm, Jens Kai

2014-01-01

accordance with the model data. In an additional step a continuous, pilot scale reactor was built to produce torrefied wood chips in large quantities. The "two-step reaction in series" model was applied to predict the mass yield of the torrefaction reaction. Parameters used for the calculation were...... at different torrefaction temperatures, it was possible to predict the HHV of torrefied wood chips from the pilot reactor. The results from this study and the presented modeling approach can be used to predict the product quality from pilot scale torrefaction reactors based on small scale experiments and could...

Impact of wood burning on outdoor air quality: existing French data and current studies

International Nuclear Information System (INIS)

Leoz-Garziandia, E.; Mandin, C.; Collet, S.; Besombes, J.L.; Pissot, N.; Allemand, N.; Riberon, J.; Jaffrezo, J.L.

2009-01-01

French source apportionment studies of air quality including the wood combustion source become widespread. Quantify a single source contribution to air quality requires to be provided with a specific measurable data to this source. For that reason, numerous studies have focused on the determination, in the atmospheric samples, of the source-specific compounds, usually called molecular tracers. Since 2000, trend works focused on the 'wood combustion' contribution to air quality have been based on the use of some tracers such as levoglucosan and metoxyphenols. Obtained results have been compared to atmospheric particles global characteristics: organic carbon (OC), elementary carbon (EC), PM 10 , PM 2.5 and polycyclic aromatic hydrocarbons (PAH). The results presented in this article show not only the interest but also the limits of such an approach, as well as the need to develop and complete the current studies in order to quantify the different sources contribution to air quality. (author)

Occurrence patterns of dead wood and wood-dependent lichens in managed boreal forest landscapes

OpenAIRE

Svensson, Måns

2013-01-01

Dead wood is a key resource for biodiversity, on which thousands of forest organisms are dependent. Because of current forest management, there has been a large-scale change in dead wood amounts and qualities, and consequently, many wood-dependent species are threatened. The general aim of this thesis is to increase our understanding of habitat requirements and occurrence patterns of wood-dependent lichens in managed, boreal forest landscapes. We surveyed dead wood and wood-dependent lichens ...

Nondestructive methods of evaluating quality of wood in preservative-treated piles

Science.gov (United States)

Xiping. Wang; Robert J. Ross; John R. Erickson; John W. Forsman; Gary D. McGinnis; Rodney C. De Groot

2000-01-01

Stress-wave-based nondestructive evaluation methods were used to evaluate the potential quality and modulus of elasticity (MOE) of wood in used preservative-treated Douglas-fir and southern pine piles. Stress wave measurements were conducted on each pile section. Stress wave propagation speeds in the piles were then obtained to estimate their MOE. This was followed by...

ANATOMICAL PROPERTIES AND FIBER QUALITY OF FIVE POTENTIAL COMMERCIAL WOOD SPECIES FROM CIANJUR, WEST JAVA

Directory of Open Access Journals (Sweden)

Ratih Damayanti

2010-06-01

Full Text Available A detailed description of wood anatomy is essential for assessing the use of a wood species for processing , and also beneficial for the identification of wood samples. Computerized keys are available that allow the identification of wood samples until the genus level; however, it is not easy to use these keys to identif y unknown species. Therefore, a database of anatomical characteristics and the computerized keys need to be completed up to species level. As the relevance, this study has examined the wood anatomical properties of the five corresponding tree species originated from Cianjur, West Java, which are commercially potential for their exploitation, i.e Castanopsis acuminatissima ADC. (Fagaceae; Castanopsistungurrut ADC. (Fagaceae; Cinnamomum inners Reinw. ex Blume (Lauraceae; Ficus nervosa Heyne (Moraceae and Horsfieldia glabra Warb. (Myristicaceae. Expectedly the results would be beneficial for wood identification purposes and evaluation for other possible uses. Obser vations on anatomical structures covered macroscopic and microscopic characteristics were carried out through the sectioned and macerated wood samples. The obser ved characteristics of the anatomical features were defined conforming to the IAWA List of Microscopic Features for Hardwood  Identification.  Based on the scrutiny on those obser ved characteristics and linked to the fiber quality, it was judged that the fiber in all the five wood species could be classified as class I for pulp and paper processing.

Analysis of High Quality Agar wood Oil Chemical Compounds By Means Of SPME/ GC-MS and Z-Score Technique

International Nuclear Information System (INIS)

Nurlaila Ismail; Mohd Ali Nor Azah; Mailina Jamil; Saiful Nizam Tajuddin; Mohd Nasir Taib

2013-01-01

Currently, the grading of the agar wood oil to the high and low quality is done using manually such as human trained grader. It was performed based on the agar wood oil physical properties such as human experience and perception and the oil colour, odor and long lasting aroma. Several researchers found that chemical profiles of the oil should be utilized to overcome the problem facing by manual techniques for example human nose cannot tolerate with the many oils at the same time, so that accurate result can be obtained in grading the agar wood oil. The analysis involved of SPME/ GC-MS and Z-score techniques have been proposed in this study to analyze the chemical compounds especially from the high quality samples of agar wood oil (Aquilariamalaccensis) from Malaysia. Two SPME fibers were used such as divinylbenzene-carbogen-polydimethylsiloxane (DVB-CAR-PDMS) and polydimethylsiloxane (PDMS) in extracting the oils compound under three different sampling temperature conditions such as 40, 60 and 80 degree Celsius. The chemical compounds extracted by SPME/ GC-MS were analyzed. The chemical compounds as identified by Z-score as significant compounds were discussed before the conclusion is made. It was found that 10-epi-γ-eudesmol, aromadendrene, β-agar ofuran, α-agar ofuran and γ-eudesmol were highlighted as significant for high quality agar wood oil and can be used as a marker compounds in classifying the agar wood oil. (author)

Microwave wood strand drying: energy consumption, VOC emission and drying quality

Energy Technology Data Exchange (ETDEWEB)

Wang, S.; Du, G.; Zhang, Y. [Tennessee Univ., Knoxville, TN (United States). Dept. of Forestry, Wildlife and Fisheries

2005-07-01

The objective of this research was to develop microwave drying technology for wood strand drying for oriented strand board (OSB) manufacturing. The advantages of microwave drying included a reduction in the drying time of wood strands and a reduction in the release of volatile organic compounds (VOC) through a decrease in the thermal degradation of the wood material. Temperature and moisture content changes under different microwave drying conditions were investigated. The effects of microwave drying on VOC emissions were evaluated and analyzed using gas chromatography and mass spectrometry. Microwave power input and the mass of drying materials in the microwave oven were found to have a dominant effect on drying quality. Results indicated that an increase in microwave power input and a decrease in sample weights resulted in high drying temperatures, short drying times and a high drying rate. The effect of microwave drying on the strand surfaces was also investigated. Different strand geometries and initial moisture content resulted in varying warm-up curves, but did not influence final moisture content. VOC emissions were quantified by comparing alpha-pinene concentrations. The microwave drying resulted in lower VOC emissions compared with conventional drying methods. It was concluded that the microwave drying technique provided faster strand drying and reduced energy consumption by up to 50 per cent. In addition, the surface wettability of wood strands dried with microwaves was better than with an industrial rotary drum drier. 12 refs., 3 tabs., 5 figs.

Implementation of new technologies in wood industry and their effect in wood products quality

OpenAIRE

ELVA ÇAUSHI; PANDELI MARKU

2014-01-01

There are about 300 companies producing furniture and about 250 small and medium enterprises (SME) producing sawn timber, which operate in the field of wood industry in Albania. This wood industry production is being challenged by the increasing demand in the domestic market, ranging from kitchen furniture to office and schools furniture, bedroom furniture, doors, windows, and saw timber in different dimensions. The production from the wood industry can fulfill about 80% of the domestic mark...

WGDB: Wood Gene Database with search interface.

Science.gov (United States)

Goyal, Neha; Ginwal, H S

2014-01-01

Wood quality can be defined in terms of particular end use with the involvement of several traits. Over the last fifteen years researchers have assessed the wood quality traits in forest trees. The wood quality was categorized as: cell wall biochemical traits, fibre properties include the microfibril angle, density and stiffness in loblolly pine [1]. The user friendly and an open-access database has been developed named Wood Gene Database (WGDB) for describing the wood genes along the information of protein and published research articles. It contains 720 wood genes from species namely Pinus, Deodar, fast growing trees namely Poplar, Eucalyptus. WGDB designed to encompass the majority of publicly accessible genes codes for cellulose, hemicellulose and lignin in tree species which are responsive to wood formation and quality. It is an interactive platform for collecting, managing and searching the specific wood genes; it also enables the data mining relate to the genomic information specifically in Arabidopsis thaliana, Populus trichocarpa, Eucalyptus grandis, Pinus taeda, Pinus radiata, Cedrus deodara, Cedrus atlantica. For user convenience, this database is cross linked with public databases namely NCBI, EMBL & Dendrome with the search engine Google for making it more informative and provides bioinformatics tools named BLAST,COBALT. The database is freely available on www.wgdb.in.

Energy wood. Part 2b: Wood pellets and pellet space-heating systems

International Nuclear Information System (INIS)

Nussbaumer, T.

2002-01-01

The paper gives an overview on pellet utilization including all relevant process steps: Potential and properties of saw dust as raw material, pellet production with drying and pelletizing, standardization of wood pellets, storage and handling of pellets, combustion of wood pellets in stoves and boilers and applications for residential heating. In comparison to other wood fuels, wood pellets show several advantages: Low water content and high heating value, high energy density, and homogeneous properties thus enabling stationary combustion conditions. However, quality control is needed to ensure constant properties of the pellets and to avoid the utilization of contaminated raw materials for the pellet production. Typical data of efficiencies and emissions of pellet stoves and boilers are given and a life cycle analysis (LCA) of wood pellets in comparison to log wood and wood chips is described. The LCA shows that wood pellets are advantageous thanks to relatively low emissions. Hence, the utilization of wood pellet is proposed as a complementary technology to the combustion of wood chips and log wood. Finally, typical fuel cost of wood pellets in Switzerland are given and compared with light fuel oil. (author)

Variation in Wood Quality in White Spruce (Picea Glauca (Moench Voss. Part I. Defining the Juvenile–Mature Wood Transition Based on Tracheid Length

Directory of Open Access Journals (Sweden)

Cyriac Serge Mvolo

2015-01-01

Full Text Available Estimations of transition age (TA and juvenile wood proportion (JWP are important for wood industries due to their impact on end-product quality. However, the relationships between analytical determination of TA based on tracheid length (TL and recognized thresholds for adequate end products have not yet been established. In this study, we used three different statistical models to estimate TA in white spruce (Picea glauca (Moench Voss based on TL radial variation. We compared the results with technological maturity. A two-millimeter threshold, previously suggested for good paper tear strength, was used. Tracheid length increased from pith to bark and from breast height to upper height. Juvenile wood (JW was conical with the three models. At breast height, TA ranged from 11 to 27 years and JWP ranged from 15.3% to 47.5% across the three models. The linear mixed model produced more conservative estimates than the maximum-quadratic-linear (M_Q_L model. Both the linear mixed model and the M_Q_L model produced more conservative TA estimates than the piecewise model. TA estimates by the MIXED model, and to a lesser extent by the M_Q_L model, were equivalent to those for real mature wood, whereas TA estimates by the piecewise model were considerably lower, falling into the transition wood area.

Energy cogeneration contributions in the wood quality as civil construction material; Contribuicoes da cogeracao de energia na qualidade da madeira como material de construcao civil

Energy Technology Data Exchange (ETDEWEB)

Lima, Carlos Roberto de

1993-07-01

This work presents the practicable technical alternative for the improvement of solid wood quality used in the building construction. Through the reality of the solid wood Amazon Region's production and actual generation conception; cogeneration, economy and efficiency on the energy application; the alternative displayed proposes the modification on the lay-out production and production process seeking the best quality obtention of the solid wood; the replace of the petroleum derived energetics by biomass (residues) and the introduction on the production site, the solid wood drying process. The production alternatives proposed can contribute for the solid wood production cost reduction, through the fuel economy, the imperfect number piece reduction and transportation cost production reduction. Contributing significantly for the cost/benefit/quality wood relations, enabling its placement of the consuming market on the Northeast, Southeast, South and Middle west Regions and so on the international market with competitive costs. (author)

Energy cogeneration contributions in the wood quality as civil construction material; Contribuicoes da cogeracao de energia na qualidade da madeira como material de construcao civil

Energy Technology Data Exchange (ETDEWEB)

Lima, Carlos Roberto de

1993-07-01

This work presents the practicable technical alternative for the improvement of solid wood quality used in the building construction. Through the reality of the solid wood Amazon Region's production and actual generation conception; cogeneration, economy and efficiency on the energy application; the alternative displayed proposes the modification on the lay-out production and production process seeking the best quality obtention of the solid wood; the replace of the petroleum derived energetics by biomass (residues) and the introduction on the production site, the solid wood drying process. The production alternatives proposed can contribute for the solid wood production cost reduction, through the fuel economy, the imperfect number piece reduction and transportation cost production reduction. Contributing significantly for the cost/benefit/quality wood relations, enabling its placement of the consuming market on the Northeast, Southeast, South and Middle west Regions and so on the international market with competitive costs. (author)

The effect of planting density on the wood quality of South African ...

African Journals Online (AJOL)

This paper presents the results of a wood property and sawn board quality study performed on disc samples and sawlogs taken from a 23-year-old Eucalyptus grandis Nelder 1a spacing trial at J.D.M. Keet plantation near Tzaneen. Ten trees from each of four markedly different planting densities were chosen to provide ...

California; Northern Sierra Air Quality Management District; Approval of Air Plan Revisions; Wood Burning Devices

Science.gov (United States)

EPA is taking final action to approve a revision to the Northern Sierra Air Quality Management District (NSAQMD) portion of the California SIP concerning emissions of particulate matter (PM) from wood burning devices.

Biophysical modelling of intra-ring variations in tracheid features and wood density of Pinus pinaster trees exposed to seasonal droughts

Science.gov (United States)

Sarah Wilkinson; Jerome Ogee; Jean-Christophe Domec; Mark Rayment; Lisa Wingate

2015-01-01

Process-based models that link seasonally varying environmental signals to morphological features within tree rings are essential tools to predict tree growth response and commercially important wood quality traits under future climate scenarios. This study evaluated model portrayal of radial growth and wood anatomy observations within a mature maritime pine (Pinus...

An Analysis of the U.S. Wood Products Import Sector: Prospects for Tropical Wood Products Exporters

Directory of Open Access Journals (Sweden)

W.A.R.T.W. Bandara

2012-10-01

Full Text Available The U.S. has dramatically altered its wood product imports and exports during the past few years,and at present, it is the second largest wood product importer in the world. Hence, an understanding ofmarket structures, factors in selecting foreign suppliers, and the emphasis placed on environmentalissues/certification are critical to understand from the perspective of wood products importers in the U.S.This study provides an analysis of the U.S. wood products import sector with special emphasis on currentand future opportunities for tropical wood products exporters to the U.S. market.In this study, 158 wood products importers in the U.S. were surveyed using a mailingquestionnaire. The adjusted response rate was 40.6 percent. Results indicated that most of the respondentswere small to medium scale firms, but major importers of wood products. According to respondents,wood products to the U.S. mainly come from Brazil, Chile, and China. From the importers’ perspective,Brazilian wood products ranked first for its quality followed by wood products from Chile and Finland.Product quality, long term customer relationships, on-time delivery of orders, fair prices, and supplierreputation were the factors deemed important in selecting overseas suppliers. Majority of respondentswere importing certified wood products. FSC, SFI, and ISO 14000 were the mostly accepted certificationprograms. However, certification was not a major factor in foreign supplier selection criteria. Whenconsidered the U.S. wood products importers’ tendency to diversify their products and species imported,attractive opportunities exist for wood products suppliers from tropical countries.

[Quantification of Wood Flour and Polypropylene in Chinese Fir/Polypropylene Composites by FTIR].

Science.gov (United States)

Lao, Wan-li; Li, Gai-yun; Zhou, Qun; Qin, Te-fu

2015-06-01

The ratio of wood and plastic in Wood Plastic Composites (WPCss) influences quality and price, but traditional thermochemical methods cannot rapidly and accurately quantify the ratio of wood/PP in WPCss. This paper was addressed to investigate the feasibility of quantifying the wood flour content and plastic content in WPCss by Fourier Transform Infrared (FTIR) spectroscopy. With Chinese fir, polypropylene (PP) and other additives as raw materials, 13 WPCs samples with different wood flour contents, ranging from 9.8% to 61.5%, were prepared by modifying wood flour, mixing materials and extrusion pelletizing. The samples were analyzed by FTIR with the KBr pellets technique. The absorption peaks of WPCss at 1059, 1 033 and 1 740 cm(-1) are considered as characteristic of Chinese fir, and the absorption peaks at 1 377, 2 839 and 841 cm(-1) are typical of PP by comparing the spectra of WPCss with that of Chinese fir, PP and other additives. The relationship between the wood flour content, PP content in WPCss and their characteristic IR peaks height ratio was established. The results show that there is a strong linear correlation between the wood flour content in WPCss and I1 059/l 1 377/I1 033, /I1377, R2 are 0.992 and 0.993 respectively; there is a high linear correlation between the PP content in WPCss and I1 377/I1 740, I2 839 /I1 740 R2 are 0.985 and 0.981, respectively. Quantitative methods of the wood flour content and PP content in WPCss by FTIR were developed, the predictive equations of the wood flour content in WPCss are y = 53.297x-9. 107 and y = 55.922x-10.238, the predictive equations of the PP content in WPCss are y = 6.828 5x+5.403 6 and y = 8.719 7x+3.295 8. The results of the accuracy test and precision test show that the method has strong repeatability and high accuracy. The average prediction relative deviations of the wood flour content and PP content in WPCss are about 5%. The prediction accuracy has been improved remarkably, compared to

When a tree falls: Controls on wood decay predict standing dead tree fall and new risks in changing forests.

Science.gov (United States)

Oberle, Brad; Ogle, Kiona; Zanne, Amy E; Woodall, Christopher W

2018-01-01

When standing dead trees (snags) fall, they have major impacts on forest ecosystems. Snag fall can redistribute wildlife habitat and impact public safety, while governing important carbon (C) cycle consequences of tree mortality because ground contact accelerates C emissions during deadwood decay. Managing the consequences of altered snag dynamics in changing forests requires predicting when snags fall as wood decay erodes mechanical resistance to breaking forces. Previous studies have pointed to common predictors, such as stem size, degree of decay and species identity, but few have assessed the relative strength of underlying mechanisms driving snag fall across biomes. Here, we analyze nearly 100,000 repeated snag observations from boreal to subtropical forests across the eastern United States to show that wood decay controls snag fall in ways that could generate previously unrecognized forest-climate feedback. Warmer locations where wood decays quickly had much faster rates of snag fall. The effect of temperature on snag fall was so strong that in a simple forest C model, anticipated warming by mid-century reduced snag C by 22%. Furthermore, species-level differences in wood decay resistance (durability) accurately predicted the timing of snag fall. Differences in half-life for standing dead trees were similar to expected differences in the service lifetimes of wooden structures built from their timber. Strong effects of temperature and wood durability imply future forests where dying trees fall and decay faster than at present, reducing terrestrial C storage and snag-dependent wildlife habitat. These results can improve the representation of forest C cycling and assist forest managers by helping predict when a dead tree may fall.

Heartwood and sapwood in eucalyptus trees: non-conventional approach to wood quality.

Science.gov (United States)

Cherelli, Sabrina G; Sartori, Maria Márcia P; Próspero, André G; Ballarin, Adriano W

2018-01-01

This study evaluated the quality of heartwood and sapwood from mature trees of three species of Eucalyptus, by means of the qualification of their proportion, determination of basic and apparent density using non-destructive attenuation of gamma radiation technique and calculation of the density uniformity index. Six trees of each species (Eucalyptus grandis - 18 years old, Eucalyptus tereticornis - 35 years old and Corymbia citriodora - 28 years old) were used in the experimental program. The heartwood and sapwood were delimited by macroscopic analysis and the calculation of areas and percentage of heartwood and sapwood were performed using digital image. The uniformity index was calculated following methodology which numerically quantifies the dispersion of punctual density values of the wood around the mean density along the radius. The percentage of the heartwood was higher than the sapwood in all species studied. The density results showed no statistical difference between heartwood and sapwood. Differently from the density results, in all species studied there was statistical differences between uniformity indexes for heartwood and sapwood regions, making justifiable the inclusion of the density uniformity index as a quality parameter for Eucalyptus wood.

Continued growth expected for wood energy despite turbulence of the economic crisis : wood energy markets, 2008-2009

Science.gov (United States)

Rens Hartkamp; Bengt Hillring; Warren Mabee; Olle Olsson; Kenneth Skog; Henry Spelter; Johan Vinterback; Antje Wahl

2009-01-01

The economic crisis has not reduced the demand for wood energy, which is expected to continue to grow. The downturn in sawmill production caused a shortage of raw material supply for wood pellet producers. With decreased demand for pulpwood-quality roundwood for wood and paper products in 2009, some pulpwood is being converted into wood energy. Economies of scale are...

Integrated production of merchantable wood and wood fuels in industry; Teollisuuden ainespuun ja puupolttoaineen integroitu tuotanto

Energy Technology Data Exchange (ETDEWEB)

Kuvaja, K [Enso Oy, Imatra (Finland). Forest Dept.

1997-12-01

The aim of this project is the economically profitable integrated harvesting of industrial wood and firewood especially in harvesting of small-diameter first thinning wood. The research in 1994 was concentrated on improvement of the quality of the chipping methods based on chain-flail debarking chipping method, and on determination of the possible utilisation targets for the fuel fraction. A reasonably large drum debarking test was also carried out at the industrial scale debarking station of the Enocell Oy. More than 80 000 m{sup 3} of first thinning wood was delivered by Enocell during this project. The quality of wood chips, produced using the chain-flail delimbing method, could be improved in the case of pine nearly to the required quality level, but additional measures are still needed in the case of birch. The fuel fraction deliveries to different points of utilisation was started. The particle size of the fuel fraction appeared to be good after crushing. In 1995 a chain-flail-drum debarking chipping unit was developed to improve and homogenise the quality of chips. (orig.)

Bio-energy in the wood processing industry. Manual for energy production from residual matter for the wood processing industry

International Nuclear Information System (INIS)

Van Halen, C.J.G.; Arninkhof, M.J.C.; Rommens, P.J.M.; Karsch, P.

2000-04-01

This manual is published within the framework of a project, financed by Novem (EWAB programme) and the European Commission (Altener programme). Similar manuals were drafted in Germany, England and Sweden. The basis of the project was the manual 'Quality manual for small-scale wood incineration and wood gasification', published by Novem in 1998. That quality manual was drafted on the basis of an evaluation of a number of wood combustion and wood gasification projects. The original manual has been improved as a result of comments made by experts in the field of bio-energy. Updated information was added with respect to legislation, financing options and new technology. Also the manual is focused more on the wood processing industry

Wood as a home heating fuel

International Nuclear Information System (INIS)

Wood, K.

1991-01-01

This article describes the development of clean-burning technology in three types of wood-burning appliances: catalytic, non-catalytic, and pellet stoves. A recent study by the Washington State Energy Extension Office concluded that in homes that use both electricity and wood, 73 megawatts of electricity/yr were saved by using wood. Since wood-burning stoves can now meet air quality standards, wood could be considered to be a greenhouse-neutral fuel if more trees are planted as they are consumed

Integrated production of merchantable wood and wood fuels in industry; Teollisuuden ainespuun ja puupoltto-aineen integroitu tuotanto

Energy Technology Data Exchange (ETDEWEB)

Kuvaja, K [Enso-Gutzeit Oy, Imatra (Finland). Forest Dept.

1997-12-31

The aim of this project is the economically profitable integrated harvesting of industrial wood and firewood especially in harvesting of small-diameter first thinning wood. The research in 1994 was concentrated on improvement of the quality of the chipping methods based on chain-flail debarking chipping method, and on determination of the possible utilization targets for the fuel fraction. A reasonably large drum debarking test was also carried out at the industrial scale debarking station of the Enocell Oy. More than 80 000 m{sup 3} of first thinning wood was delivered by Enocell during this project. The quality of wood chips, produced using the chain-flail delimbing method, could be improved in the case of pine nearly to the required quality level, but additional measures are still needed in the case of birch. The fuel fraction deliveries to different points of utilization was started. The particle size of the fuel fraction appeared to be good after crushing. In 1995 a chain-flail-dry drum debarking chipping unit was developed to improve and homogenize the quality of chips

Integrated production of merchantable wood and wood fuels in industry; Teollisuuden ainespuun ja puupoltto-aineen integroitu tuotanto

Energy Technology Data Exchange (ETDEWEB)

Kuvaja, K. [Enso-Gutzeit Oy, Imatra (Finland). Forest Dept.

1996-12-31

The aim of this project is the economically profitable integrated harvesting of industrial wood and firewood especially in harvesting of small-diameter first thinning wood. The research in 1994 was concentrated on improvement of the quality of the chipping methods based on chain-flail debarking chipping method, and on determination of the possible utilization targets for the fuel fraction. A reasonably large drum debarking test was also carried out at the industrial scale debarking station of the Enocell Oy. More than 80 000 m{sup 3} of first thinning wood was delivered by Enocell during this project. The quality of wood chips, produced using the chain-flail delimbing method, could be improved in the case of pine nearly to the required quality level, but additional measures are still needed in the case of birch. The fuel fraction deliveries to different points of utilization was started. The particle size of the fuel fraction appeared to be good after crushing. In 1995 a chain-flail-dry drum debarking chipping unit was developed to improve and homogenize the quality of chips

Nondestructive evaluation of green wood using stress wave and transverse vibration techniques

Science.gov (United States)

Udaya B. Halabe; Gangadhar M. Bidigalu; Hota V.S. GangaRao; Robert J. Ross

1997-01-01

Longitudinal stress wave and transverse vibration nondestructive testing (NDT) techniques have proven to be accurate means of evaluating the quality of wood based products. Researchers have found strong relationships between stress wave and transverse vibration parameters (e.g., wave velocity and modulus of elasticity predicted using NDT measurements) with the actual...

PENGARUH UMUR POHON, BONITA DAN POSISI AKSIAL BATANG TERHADAP STRUKTUR MAKROSKOPIS DAN KUALITAS KAYU JATI SEBAGAI BAHAN FURNITUR (Effect of Tree Age, Site Quality Index and Trunk Axial Position on Macroscopic Structure and Quality of Teak Wood

Directory of Open Access Journals (Sweden)

Yustinus Suranto

2015-03-01

is an alternative solution of limited raw materials faced by furniture industry. Young wood tends to have a low-quality wood. One element for measuring wood quality is wood macroscopic structure properties. This study was aimed to determine the effect of tree age, site quality index and axial stem position on wood structures and wood quality. Thirty-six young teak trees were harvested on forest areas of Kendal Forest District, Central Java Province. Three disks were taken from each trunk, namely from the butt, middle and upper parts. Heartwood proportion and annual ring dimensions were measured based on natural color difference by using millimeter grid apparatus. Data were analyzed by using variance analysis arranged in blocked factorial and further testing were performed by using HSD Duncan. Wood quality was analyzed using determinant method which elaborated based on Z norm curve. Results showed that interaction of three factors did not affect on heart-wood proportion and growth ring dimensions. Interaction of age classes and site quality index influence significantly on heart-wood proportion and growth ring dimensions. Stem axial position significantly affects on heart-wood proportion and very significantly effect on growth ring dimensions. The lower wood position, the higher heart-wood proportion and the wider growth ring dimensions. Interaction of three factors namely class age V, site quality index 4 and middle trunk position has a highest wood quality, namely class 2, but interaction of age class V, site quality index 3 and top trunk has the lowest one, namely class 4. The use of wood-based quality will maximize the value and increase the product lifespan, thereby reducing the intensity of logging and become more environmental friendly.

Okanagan indoor wood burning appliance inventory survey

International Nuclear Information System (INIS)

2001-01-01

A survey was conducted to determine the usage and nature of wood burning appliances used by residents in British Columbia's Okanagan region. The objective was to better understand this source of air quality concern and to facilitate strategic planning, guidelines and legislation. The survey also provides a baseline to track the effectiveness of any reduction strategies. It identifies the different types of wood burning appliances used in the community and presents residential options about potential bylaws to protect air quality. The receptivity of households to switch to more efficient wood burning appliances was also examined. The survey completes a portion of an overall emissions inventory for the Okanagan Valley. Environment Canada uses the particulate loading results to model the air quality in the airshed. Results showed that approximately 21 per cent of the households in the Okanagan use indoor wood burning appliances, and burn an average of 2.3 cords of wood each year. Only 11 per cent of the appliances are considered to have advanced burning technology. It is projected that the use of wood burning appliances in the Okanagan will increase by 5 to 7 per cent in the next 2 years. Most residents have good burning habits, but some improvements can still be made. Many residents are considering exchanging old wood burning appliances for clean burning technology appliances for environmental and health reasons. Most households would support a bylaw to control nuisance amounts of smoke from wood burning appliances. 20 tabs., 5 figs

Predictive Modeling of Black Spruce (Picea mariana (Mill. B.S.P. Wood Density Using Stand Structure Variables Derived from Airborne LiDAR Data in Boreal Forests of Ontario

Directory of Open Access Journals (Sweden)

Bharat Pokharel

2016-12-01

Full Text Available Our objective was to model the average wood density in black spruce trees in representative stands across a boreal forest landscape based on relationships with predictor variables extracted from airborne light detection and ranging (LiDAR point cloud data. Increment core samples were collected from dominant or co-dominant black spruce trees in a network of 400 m2 plots distributed among forest stands representing the full range of species composition and stand development across a 1,231,707 ha forest management unit in northeastern Ontario, Canada. Wood quality data were generated from optical microscopy, image analysis, X-ray densitometry and diffractometry as employed in SilviScan™. Each increment core was associated with a set of field measurements at the plot level as well as a suite of LiDAR-derived variables calculated on a 20 × 20 m raster from a wall-to-wall coverage at a resolution of ~1 point m−2. We used a multiple linear regression approach to identify important predictor variables and describe relationships between stand structure and wood density for average black spruce trees in the stands we observed. A hierarchical classification model was then fitted using random forests to make spatial predictions of mean wood density for average trees in black spruce stands. The model explained 39 percent of the variance in the response variable, with an estimated root mean square error of 38.8 (kg·m−3. Among the predictor variables, P20 (second decile LiDAR height in m and quadratic mean diameter were most important. Other predictors describing canopy depth and cover were of secondary importance and differed according to the modeling approach. LiDAR-derived variables appear to capture differences in stand structure that reflect different constraints on growth rates, determining the proportion of thin-walled earlywood cells in black spruce stems, and ultimately influencing the pattern of variation in important wood quality attributes

Hogged wood fuel price analysis in the U.S. Pacific Northwest

International Nuclear Information System (INIS)

Biederman, R.T.; Blazek, C.F.; Fox, P.J.

1991-01-01

The purpose of this paper is to discuss the results of a comprehensive analysis of wood residues used for meeting energy requirements in the Pacific Northwest region of the United States. These wood residues are generated primarily from cutting, sawing, planning, sanding, and debarking activities in the lumber and plywood industries. While high-quality wood residues are commonly used as raw material in the manufacture of pulp and board commodities, a very large amount of wood residues are ultimately used for plant fuel purposes. The characteristics of this market for hogged wood fuel are examined in depth, with particular emphasis given to the factors which affect the supply, demand and price of hogged wood. Hogged wood has played an enormous role in the Pacific Northwest for over sixty years, a result of the massive regional timber harvest. Utilization of this renewable energy resource continues to be a large component in regional energy supply. Despite having a large number of highly integrated mills that both use and produce wood residues, the Pacific Northwest region experiences a lively trade in hogged wood. The IGT study discussed herein examines the determinants of the regional market price for hogged wood. A number of useful leading indicators are identified, and a statistical forecasting model is prepared to help predict future hogged wood prices. This model provides insight into the factors that are, and are not, important determinants of hogged wood price. The issue of fuel substitution is addressed in relation to the potential of hogged wood to displace some amount of primary energy sources such as natural gas and electricity. Also examined in the study are techniques to estimate the actual quantity of hogged wood available, and the quantity demanded by the marketplace. Conclusions presented in the study have important ramifications for understanding the price behavior and utilization of hogged wood fuel. 4 refs., 12 figs

Bond quality of phenol-based adhesives containing liquefied creosote-treated wood

Science.gov (United States)

Chung-Yun Hse; Feng Fu; Hui Pan

2009-01-01

Liquefaction of spent creosote-treated wood was studied to determine the technological practicability of its application in converting treated wood waste into resin adhesives. A total of 144 plywood panels were fabricated with experimental variables included 2 phenol to wood (P/W) ratios in liquefaction, 6 resin formulations (3 formaldehyde/liquefied wood (F/...

Adhesion quality of glued joints from different commercial wood species

Directory of Open Access Journals (Sweden)

Alexandre Miguel do Nascimento

2013-12-01

Full Text Available The objective of this study was to determine the effect of wood density, adhesive type and gluing pressure on the shear strength of glued joints of fourteen commercial wood species. Wood pieces were classified in three density classes (Class 1: less than 0.55 g cm-3; Class 2: from 0.55 to 0.75 g cm-3; and Class 3: greater than 0.75 g cm-3 and joints bonded with two adhesives: polyvinyl acetate (PVA and urea-formaldehyde (UF, under two different pressures: 6 and 12 kgf cm-2. Glued joints bonded with PVA adhesive presented higher shear strength than those bonded with UF adhesive. For percentage of wood failure, the PVA adhesive had the best performance, however, only Classes 1 and 2 reached the values required by ASTM 3110 standard. Glued joints from Class 3, bonded with UF adhesive, did not reach the values of solid wood. The gluing pressure of 12 kgf cm-2 was more efficient for Class 3, for both shear strength and percentage of wood failure.

On the Effect of Unit-Cell Parameters in Predicting the Elastic Response of Wood-Plastic Composites

Directory of Open Access Journals (Sweden)

Fatemeh Alavi

2013-01-01

Full Text Available This paper presents a study on the effect of unit-cell geometrical parameters in predicting elastic properties of a typical wood plastic composite (WPC. The ultimate goal was obtaining the optimal values of representative volume element (RVE parameters to accurately predict the mechanical behavior of the WPC. For each unit cell, defined by a given combination of the above geometrical parameters, finite element simulation in ABAQUS was carried out, and the corresponding stress-strain curve was obtained. A uniaxial test according to ASTM D638-02a type V was performed on the composite specimen. Modulus of elasticity was determined using hyperbolic tangent function, and the results were compared to the sets of finite element analyses. Main effects of RVE parameters and their interactions were demonstrated and discussed, specially regarding the inclusion of two adjacent wood particles within one unit cell of the material. Regression analysis was performed to mathematically model the RVE parameter effects and their interactions over the modulus of elasticity response. The model was finally employed in an optimization analysis to arrive at an optimal set of RVE parameters that minimizes the difference between the predicted and experimental moduli of elasticity.

Strength of wood versus rate of testing - A theoretical approach

DEFF Research Database (Denmark)

Nielsen, Lauge Fuglsang

2007-01-01

Strength of wood is normally measured in ramp load experiments. Experience shows that strength increases with increasing rate of testing. This feature is considered theoretically in this paper. It is shown that the influence of testing rate is a phenomenon, which depends on the quality...... of the considered wood. Low quality wood shows lesser influence of testing rate. This observation agrees with the well-known statement made by Borg Madsen that weak wood subjected to a constant load, has a longer lifetime than strong wood. In general, the influence of testing rate on strength increases...

Moisture-driven fracture in solid wood

DEFF Research Database (Denmark)

Larsen, Finn; Ormarsson, Sigurdur; Olesen, John Forbes

2011-01-01

Moisture-induced fractures in solid timber create considerable problems for both building industries and sawmills. Cracks caused by kiln-drying of solid timber are extremely difficult to predict. This paper reports on experiments concerned with methods of reducing cracks in wood and with the crac......Moisture-induced fractures in solid timber create considerable problems for both building industries and sawmills. Cracks caused by kiln-drying of solid timber are extremely difficult to predict. This paper reports on experiments concerned with methods of reducing cracks in wood...... process, suggesting that sealing the ends of timber logs while in the green moisture state could considerably reduce the development of end-cracks. The initial moisture content and the shrinkage properties of the wood varied markedly from pith to bark. The importance of taking material inhomogeneities...... into account when modelling crack propagation in solid wood is emphasized. © 2011 Taylor & Francis....

Energy use of decayed wood; Lahopuun maeaerae, sisaeltoe ja hankintakustannukset

Energy Technology Data Exchange (ETDEWEB)

Maekelae, M; Lipponen, K [Metsaeteho Oy, Helsinki (Finland)

1997-12-01

A study of the quality, amounts and delivery costs of decayed wood available for possible energy use will be carried out in co-operation by Metsaeteho and Forest Research Institute. The work will consist of the following sub-studies: Quality of decayed wood available for possible energy use, quantities of decayed wood available for possible energy use by municipalities in Western and Southern Finland, harvesting, transport and chipping costs of decayed wood in different delivery alternatives and as a practical example, quantities of decayed wood available for possible energy use in two potential consumption municipalities. (orig.)

Air quality and residential wood combustion - application of the model system SIMAIRrwc for some Swedish municipalities; Luftkvalitet och smaaskalig biobraensleeldning. Tillaempningar av SIMAIRved foer naagra kommuner

Energy Technology Data Exchange (ETDEWEB)

Omstedt, Gunnar; Andersson, Stefan; Johansson, Christer; Loefgren, Bengt-Erik

2008-11-15

SIMAIRrwc is a Web based evaluation tool for meeting the EU directive on air pollution limits in residential areas using wood combustion. The background is a four-year research program (2001-2004) called Biomass Combustion Health and Environment. Some conclusions from this program were that emissions from small scale wood combustion can influence human health mainly due to high emitting old wood stoves during cold weather conditions and that the air quality in such areas can improve significantly if old wood stoves were replaced by modern wood boilers attached to a storage tank or with a pellet boiler. SIMAIRrwc is based on the same principles as SIMAIRroad, which is a Web based evaluation tool for road traffic i.e. coupled model system using different models on local, urban and regional geographical scales, best available emission data, but at the same time presented in a very simplified way. In this project SIMAIRrwc has been applied in five different Swedish municipalities. The aim has been to apply and improve the model in cooperation with the municipalities. The conclusions from the project are: Small scale wood combustions in residential areas are local problems which sometimes include only a few houses and/or wood-burners. Air quality problems related to the EU directive are mainly due to particles. Combinations of residential areas with wood combustion and emissions from nearby dense traffic roads might give rise to bad air quality. Actions require knowledge about individual equipment which needs information from the local chimney sweeps. The best way to identify problem areas is to use model calculations. If model calculations indicate risks of exceeding air quality limits, then new calculations should be made with improved input data taking into account for example information of district heating or other installations that can effect the emissions. Before actions are taken it may also be useful to make measurements. The measurement site can then be

Wood Export and Deposition Dynamics in Mountain Watersheds

Science.gov (United States)

Senter, Anne Elizabeth

Wood dynamics that store, transport, break down, and ultimately export wood pieces through watershed networks are key elements of stream complexity and ecosystem health. Efforts to quantify wood processes are advancing rapidly as technological innovations in field data collection, remotely sensed data acquisition, and data analyses become increasingly sophisticated. The ability to extend the temporal and spatial scales of wood data acquisition has been particularly useful to the investigations presented herein. The primary contributions of this dissertation are focused on two aspects of wood dynamics: watershed-scale wood export processes as identified using the depositional environment of a mountain reservoir, and wood deposition mechanisms in a bedrock-dominated mountain river. Three chapters present this work: In Chapter 1, continuous video monitoring of wood in transport revealed seasonal and diurnal hydrologic cycle influences on the variable rates at which wood transports. This effort supports the efficacy of utilizing continuous data collection methods for wood transport studies. Annual wood export data were collected via field efforts and aerial image analyses from New Bullards Bar Reservoir on the North Yuba River, Sierra Nevada, California. Examination of data revealed linkages between decadal-scale climatic patterns, large flood events, and episodic wood export quantities. A watershed-specific relation between wood export quantities and annual peak discharge contributes to the notion that peak discharge is a primary control on wood export, and yielded prediction of annual wood export quantities where no data were available. Linkages between seasonality, climatic components, and hydrologic events that exert variable control on watershed scale wood responses are presented as a functional framework. An accompanying conceptual model supports the framework presumption that wood responses are influenced by seasonal variations in Mediterranean-montane climate

Relating wood properties to handsheet porosity and mechanical strength

CSIR Research Space (South Africa)

Maharaj, S

2006-11-01

Full Text Available , 4041 3CSIR, Forestry and Forest Products Research Centre, P.O. Box 17001, Congella, 4013 WOOD HAND-SHEET (STRENGTH) PROCESSING Anatomy Chemistry Density Tear Tensile Burst Background Variation in pulp mills •Need to predict quality of end... important concepts… Some important concepts… • Collapsibility and inter-fibre bonding Light Microscopy SEM • Tear – Fibre level: pull-out vs. breaking/rupture Some important concepts… •Fibre breakage / rupture: less energy = lower tear strength...

Detritus Quality and Locality Determines Survival and Mass, but Not Export, of Wood Frogs at Metamorphosis.

Directory of Open Access Journals (Sweden)

Joseph R Milanovich

Full Text Available Single-site experiments have demonstrated detritus quality in wetlands can have strongly negative, neutral, and even positive influences on wildlife. However, an examination of the influence of detritus quality across several regions is lacking and can provide information on whether impacts from variation in detritus quality are consistent across species with wide ranges. To address this gap in regional studies we examined effects of emergent and allochthonous detritus of different nutrient qualities on amphibians and assessed a mechanism that may contribute to potential impacts. We used aquatic mesocosms to raise wood frogs (Rana sylvatica from two regions of the United States with whole plants from purple loosestrife (Lythrum salicaria, leaf litter from native hardwood trees, and a mixture of both. We examined several metrics of amphibian fitness and life history, including survival, number of days to metamorphosis, and size at metamorphosis. Further, we quantified whether the effects of detritus type could translate to variation in anuran biomass or standing stock of nitrogen or phosphorus export. Our results show detritus with high nutrient quality (purple loosestrife negatively influenced survival of wood frogs, but increased size of metamorphic individuals in two different regions of the United States. Despite the decrease in survival, the increase in size of post-metamorphic anurans raised with high quality detritus resulted in anuran biomass and standing stock of N and P export being similar across treatments at both locations. These results further demonstrate the role of plant quality in shaping wetland ecosystem dynamics, and represent the first demonstration that effects are consistent within species across ecoregional boundaries.

Quality of groundwater and surface water, Wood River Valley, south-central Idaho, July and August 2012

Science.gov (United States)

Hopkins, Candice B.; Bartolino, James R.

2013-01-01

Residents and resource managers of the Wood River Valley of south-central Idaho are concerned about the effects that population growth might have on the quality of groundwater and surface water. As part of a multi-phase assessment of the groundwater resources in the study area, the U.S. Geological Survey evaluated the quality of water at 45 groundwater and 5 surface-water sites throughout the Wood River Valley during July and August 2012. Water samples were analyzed for field parameters (temperature, pH, specific conductance, dissolved oxygen, and alkalinity), major ions, boron, iron, manganese, nutrients, and Escherichia coli (E.coli) and total coliform bacteria. This study was conducted to determine baseline water quality throughout the Wood River Valley, with special emphasis on nutrient concentrations. Water quality in most samples collected did not exceed U.S. Environmental Protection Agency standards for drinking water. E. coli bacteria, used as indicators of water quality, were detected in all five surface-water samples and in two groundwater samples collected. Some analytes have aesthetic-based recommended drinking water standards; one groundwater sample exceeded recommended iron concentrations. Nitrate plus nitrite concentrations varied, but tended to be higher near population centers and in agricultural areas than in tributaries and less populated areas. These higher nitrate plus nitrite concentrations were not correlated with boron concentrations or the presence of bacteria, common indicators of sources of nutrients to water. None of the samples collected exceeded drinking-water standards for nitrate or nitrite. The concentration of total dissolved solids varied considerably in the waters sampled; however a calcium-magnesium-bicarbonate water type was dominant (43 out of 50 samples) in both the groundwater and surface water. Three constituents that may be influenced by anthropogenic activity (chloride, boron, and nitrate plus nitrite) deviate from this

Reservoir characterization and performance predictions for the E.N. Woods lease

Energy Technology Data Exchange (ETDEWEB)

Aka-Milan, Francis A.

2000-07-07

The task of this work was to evaluate the past performance of the E.N. WOODS Unit and to forecast its future economic performance by taking into consideration the geology, petrophysics and production history of the reservoir. The Decline Curve Analysis feature of the Appraisal of Petroleum Properties including Taxation Systems (EDAPT) software along with the Production Management Systems (PMS) software were used to evaluate the original volume of hydrocarbon in place and estimate the reserve. The Black Oil Simulator (BOAST II) was then used to model the waterflooding operation and estimate the incremental oil production attributable to the water injection. BOAST II was also used to predict future performance of the reservoir.

Modeling relaxation length and density of acacia mangium wood using gamma - ray attenuation technique

International Nuclear Information System (INIS)

Tamer A Tabet; Fauziah Abdul Aziz

2009-01-01

Wood density measurement is related to the several factors that influence wood quality. In this paper, density, relaxation length and half-thickness value of eight ages, 3, 5, 7, 10, 11, 13 and 15 year-old of Acacia mangium wood were determined using gamma radiation from 137 Cs source. Results show that Acacia mangium tree of age 3 year has the highest relaxation length of 83.33 cm and least density of 0.43 gcm -3 , while the tree of age 15 year has the least Relaxation length of 28.56 cm and highest density of 0.76 gcm -3 . Results also show that the 3 year-old Acacia mangium wood has the highest half thickness value of 57.75 cm and 15 year-old tree has the least half thickness value of 19.85 cm. Two mathematical models have been developed for the prediction of density, variation with relaxation length and half-thickness value of different age of tree. A good agreement (greater than 85% in most cases) was observed between the measured values and predicted ones. Very good linear correlation was found between measured density and the age of tree (R2 = 0.824), and between estimated density and Acacia mangium tree age (R2 = 0.952). (Author)

Studies of non-contact methods for roughness measurements on wood surfaces

International Nuclear Information System (INIS)

Lundberg, I.A.S.; Porankiewicz, B.

1995-01-01

The quality of wood surfaces after different kinds of machining processes is a property of great importance for the wood processing industries. Present work is a study, whose objective was to evaluate different non-contact methods, for measurement of the quality of the wood surfaces by correlating them with stylus tracing. A number of Scots Pine samples were prepared by different kinds of wood machining processing. Surface roughness measurements were performed, utilizing two optical noncontact methods. The results indicate that the laser scan method can measure surface roughness on sawn wood with a sufficient degree of accuracy. (author) [de

Wood pellets : a worldwide fuel commodity

International Nuclear Information System (INIS)

Melin, S.

2005-01-01

Aspects of the wood pellet industry were discussed in this PowerPoint presentation. Details of wood pellets specifications were presented, and the wood pellet manufacturing process was outlined. An overview of research and development activities for wood pellets was presented, and issues concerning quality control were discussed. A chart of the effective calorific value of various fuels was provided. Data for wood pellet mill production in Canada, the United States and the European Union were provided, and various markets for Canadian wood pellets were evaluated. Residential sales as well as Canadian overseas exports were reviewed. Production revenues for British Columbia and Alberta were provided. Wood pellet heat and electricity production were discussed with reference to prefabricated boilers, stoves and fireplaces. Consumption rates, greenhouse gas (GHG) emissions, and fuel ratios for wood pellets and fossil fuels were compared. Price regulating policies for electricity and fossil fuels have prevented the domestic expansion of the wood pellet industry. There are currently no incentives for advanced biomass combustion to enter British Columbia markets, and this has led to the export of wood pellets. It was concluded that climate change mitigation policies will be a driving force behind market expansion for wood pellets. tabs., figs

Fungal bio-treatment of spruce wood with Trametes versicolor for pitch control: Influence on extractive contents, pulping process parameters, paper quality and effluent toxicity

NARCIS (Netherlands)

Beek, van T.A.; Kuster, B.; Claassen, F.W.; Tienvieri, T.; Bertaud, F.; Lennon, G.; Petit-Concil, M.; Sierra-Alvarez, R.

2007-01-01

Lipophilic low molar-mass constituents in wood chips for the paper industry result in low quality pulp, pitch deposition, and effluent toxicity. New biotechnological solutions such as fungal pre-treatment of wood chips can reduce pitch problems. This laboratory-scale study focuses on the potential

Air quality and composite wood products

Science.gov (United States)

Melissa G. D. Baumann

1999-01-01

Research at the USDA Forest Service, Forest Products Laboratory (FPL) is being conducted to identify the compounds emitted from wood products during their manufacture and subsequent use. The FPL researchers are measuring the types and quantities of VOCs that are emitted from particleboard and MDF products to provide quantitative emissions information. This information...

Estimating wood volume from canopy area in deciduous woodlands ...

African Journals Online (AJOL)

In this study we tested the predictive ability of canopy area in estimating wood volume in deciduous woodlands of Zimbabwe. The study was carried out in four sites of different climatic conditions. We used regression analysis to statistically quantify the prediction of wood volume from canopy area at species and stand level ...

Hydrologic Analysis of Fort Leonard Wood, Missouri

Science.gov (United States)

2015-08-01

drainage areas are different, hydrological analysis will be conducted on the two basins individually. The results of the two analyses will be combined to...ER D C TR -1 5- 4 Environmental Quality and Installations Hydrologic Analysis of Fort Leonard Wood, Missouri En gi ne er R es ea rc h...Environmental Quality and Installations ERDC TR-15-4 August 2015 Hydrologic Analysis of Fort Leonard Wood, Missouri Michael L. Follum, Darla C. McVan

Wood ethanol and synthetic natural gas pathways

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-11-30

This report provided details of updates to the wood ethanol pathway recently added to the GHGenius model, an analytical tool used to analyze emissions from conventional and alternative fuel combustion processes. The pathway contains data developed by the United States Department of Energy. A number of co-products were added to the wood and agricultural residue pathways, including furfural, xylitol, lignin, and glycerol. New chemical inputs included nitrogen gas, ammonia, enzymes and yeast. Biological ethanol pathways were reviewed, and separate inputs for wood, agricultural residues, corn ethanol, and wheat ethanol were added. The model was updated to reflect current research conducted on the gasification of wood and the upgrading of the gas to produce pipeline quality natural gas. New process developments in producing pipeline quality gas from coal were also added. The ability to model enzyme consumption was added to all ethanol pathways. 25 refs., 41 tabs., 8 figs.

Wood ethanol and synthetic natural gas pathways

International Nuclear Information System (INIS)

2006-01-01

This report provided details of updates to the wood ethanol pathway recently added to the GHGenius model, an analytical tool used to analyze emissions from conventional and alternative fuel combustion processes. The pathway contains data developed by the United States Department of Energy. A number of co-products were added to the wood and agricultural residue pathways, including furfural, xylitol, lignin, and glycerol. New chemical inputs included nitrogen gas, ammonia, enzymes and yeast. Biological ethanol pathways were reviewed, and separate inputs for wood, agricultural residues, corn ethanol, and wheat ethanol were added. The model was updated to reflect current research conducted on the gasification of wood and the upgrading of the gas to produce pipeline quality natural gas. New process developments in producing pipeline quality gas from coal were also added. The ability to model enzyme consumption was added to all ethanol pathways. 25 refs., 41 tabs., 8 figs

Comparison of Different Wood Species as Raw Materials for Bioenergy

Directory of Open Access Journals (Sweden)

Bojana Klašnja

2013-12-01

Full Text Available Background and Purpose: Most projections of the global energy use predict that biomass will be an important component of primary energy sources in the coming decades. Short rotation plantations have the potential to become an important source of renewable energy in Europe because of the high biomass yields, a good combustion quality as solid fuel, ecological advantages and comparatively low biomass production costs. Materials and Methods: In this study, the wood of black locust Robinia pseudoacacia, white willow Salix alba L., poplars Populus deltoides and Populus x euramericana cl.I-214, aged eight years were examined. Immediately after the felling, sample discs were taken to assess moisture content, ash content, the width of growth rings, wood densities and calorific values, according to the standard methodology. Results:The mean values of willow, poplar and black locust wood density were 341 kg/m3, 336 kg/m3 and 602 kg/m3,respectively. The average heating values of willow poplar and black locust wood were 18.599 MJ/kg, 18.564 MJ/kg and 21.196 MJ/kg, respectively. The FVI index (average values was higher for black locust (17.186 than for poplar and willow clones, which were similar: 11.312 and 11.422 respectively. Conclusions: Black locust wood with a higher density, calorific value and ash content compared to poplar and willow wood proved to be a more suitable raw material as RES. However, it is very important, from the aspect of the application of wood of these tree species as RES, to also consider the influence of the biomass yield per unit area of the plantations established as “energy plantations”.

Wood decay and the cleanup crew

Science.gov (United States)

Kevin T. Smith; Jessie A. Glaeser

2017-01-01

Arborists are encouraged to recognize the wood-decay process as an important factor in tree health and public safety. Technical experts who develop training materials to recognize wood-decay processes in living trees are frequently forest pathologists. Much of the history of forest pathology was to support production of sound, high-quality timber. That heritage is...

Significance of wood extractives for wood bonding.

Science.gov (United States)

Roffael, Edmone

2016-02-01

Wood contains primary extractives, which are present in all woods, and secondary extractives, which are confined in certain wood species. Extractives in wood play a major role in wood-bonding processes, as they can contribute to or determine the bonding relevant properties of wood such as acidity and wettability. Therefore, extractives play an immanent role in bonding of wood chips and wood fibres with common synthetic adhesives such as urea-formaldehyde-resins (UF-resins) and phenol-formaldehyde-resins (PF-resins). Extractives of high acidity accelerate the curing of acid curing UF-resins and decelerate bonding with alkaline hardening PF-resins. Water-soluble extractives like free sugars are detrimental for bonding of wood with cement. Polyphenolic extractives (tannins) can be used as a binder in the wood-based industry. Additionally, extractives in wood can react with formaldehyde and reduce the formaldehyde emission of wood-based panels. Moreover, some wood extractives are volatile organic compounds (VOC) and insofar also relevant to the emission of VOC from wood and wood-based panels.

P.E.I. wood fuel survey, 1990-91

International Nuclear Information System (INIS)

1991-04-01

In 1991 a wood fuel survey of 450 randomly selected households, representing 1% of the total number of households in Prince Edward Island, was conducted. The survey indicated that 49.8% of the households burned wood, up from 42.1% of households in the 1988-1989 survey. The wood burning households consumed an average of 4.92 cords of wood, consistent with the 4.90 cords in the 1989 survey. The total residential wood consumption was estimated at ca 100,377 cords, an increase from the 89,000 cords used in 1988-89. Wood cutters represented 23.4% of respondents, with buyers representing 25.4% of respondents. The wood burning appliances used by the respondents were: airtight wood stove 39.9%, wood furnace 22.5%, kitchen wood stove 15.7%, combined wood/oil furnace 8.9%, Franklin/non-airtight 4.4%, Kemac unit 4.4%, fireplace insert 3.1%, and open fireplace 1%. The most frequent response among rural wood users cited price as an advantage of wood fuel, while the most frequent response of urban users cited the quality of the heat. 9 figs., 47 tabs

Status of wood-based industries in Malaysia

International Nuclear Information System (INIS)

Dahlan Haji Mohd

1987-01-01

Malaysia is one of the biggest suppliers of tropical wood in the world. However, less than 10% of the timber exported have gone through secondary processing. It is high time for this country to concentrate more on the secondary and tertiary sectors with the use of new technology such as radiation curing of coatings, in order to improve the quality of wood products. This paper examines where the strength and potential of the local wood industry lie. (author)

Impact of fuel quality and burner capacity on the performance of wood pellet stove

OpenAIRE

Petrović-Bećirović Sanja B.; Manić Nebojša G.; Stojiljković Dragoslava D.

2015-01-01

Pellet stoves may play an important role in Serbia in the future when fossil fuel fired conventional heating appliances are replaced by more efficient and environmentally friendly devices. Experimental investigation was conducted in order to examine the influence of wood pellet quality, as well as burner capacity (6, 8 and 10 kW), used in the same stove configuration, on the performance of pellet stove with declared nameplate capacity of 8 kW. The results o...

Wood plastic combination

International Nuclear Information System (INIS)

Cunanan, S.A.; Bonoan, L.S.; Verceluz, F.P.; Azucena, E.A.

1976-03-01

The purpose of this study is to improve the physical and mechaniproperties of local inferior quality wood species by radiation-induced graft polymerization with plastic monomers. The process involves the following: 1) Preparation of sample; 2) Impregnation of sample with the monomers; 3) Irradiation of the impregnated sample with the use of 20,000 curie Co-60 as gamma-source; 4) Drying of irradiated sample to remove the unpolymerized monomer. Experimentation on different wood species were undertaken and the results given. From the results obtained, it can be concluded that the monomers systems MMA, MMA-USP, and styrene-USP are suitable for graft polymerization with the wood species almon, apitong, bagtikan, mayapis, red lauan, and tanguile. This is shown by their maximum conversion value which range from 86% to 96% with the optimum dose range of 1 to 2 Mrads. However, in the application of WPC process, properties that are required in a given wood product must be considered, thus aid in the selection of the monomer system to be used with a particular wood species. Some promising applications of WPC is in the manufacture of picker sticks, shuttles, and bobbins for the textile industry. However, there is a need for a pilot plant scale study so that an economic assessment of the commercial feasibility of this process can be made

Gluebond strength of laser cut wood

Science.gov (United States)

Charles W. McMillin; Henry A. Huber

1985-01-01

The degree of strength loss when gluing laser cut wood as compared to conventionally sawn wood and the amount of additional surface treatment needed to improve bond quality were assessed under normal furniture plant operating conditions. The strength of laser cut oak glued with polyvinyl acetate adhesive was reduced to 75 percent of sawn joints and gum was reduced 43...

Analytical solutions for prediction of the ignition time of wood particles based on a time and space integral method

NARCIS (Netherlands)

Haseli, Y.; Oijen, van J.A.; Goey, de L.P.H.

2012-01-01

The main idea of this paper is to establish a simple approach for prediction of the ignition time of a wood particle assuming that the thermo-physical properties remain constant and ignition takes place at a characteristic ignition temperature. Using a time and space integral method, explicit

Wood density variation in Gmelina arborea trees using X-ray densitometry

International Nuclear Information System (INIS)

Roque, Roger Moya; Tomazello, Mario

2005-01-01

The wood density constitutes the main wood quality parameter by its relationship with anatomical, physical and chemical properties and wood utilization. The modern and accurate methods - like X-ray densitometry - are applied to determine the density spatial distribution in wood sections and pith-bark direction. On the other hand, emphasis to wood utilization from fast growing plantations, like Gmelina arborea in Costa Rica, has been done. The objectives of this study were to determinate the influence of 2 climatic conditions of Costa Rica on radial wood density variation of gmelina trees form fast growing plantations using the X-ray densitometry method. Wood samples were cut at DBH of gmelina trees and transversal thin laths were selected at north-south direction and conditioned at 12% moisture content equilibrium and X-rayed. The radiographic films were revealed and scanned a 256 gray scale with 1000 dpi resolution and the intra tree-ring density were determined by CRAD and CERD software. The results demonstrated that the climatic and forest management affects the wood density variability and the distinctness of tree-ring boundaries of gmelina trees, as well as, the applicability of X-ray densitometry in wood quality analysis. (author)

Quality-assurance procedures: Method 5G determination of particulate emissions from wood heaters from a dilution tunnel sampling location

Energy Technology Data Exchange (ETDEWEB)

Ward, T.E.; Hartman, M.W.; Olin, R.C.; Rives, G.D.

1989-06-01

Quality-assurance procedures are contained in this comprehensive document intended to be used as an aid for wood-heater manufacturers and testing laboratories in performing particulate matter sampling of wood heaters according to EPA protocol, Method 5G. These procedures may be used in research and development, and as an aid in auditing and certification testing. A detailed, step-by-step quality assurance guide is provided to aid in the procurement and assembly of testing apparatus, to clearly describe the procedures, and to facilitate data collection and reporting. Suggested data sheets are supplied that can be used as an aid for both recordkeeping and certification applications. Throughout the document, activity matrices are provided to serve as a summary reference. Checklists are also supplied that can be used by testing personnel. Finally, for the purposes of ensuring data quality, procedures are outlined for apparatus operation, maintenance, and traceability. These procedures combined with the detailed description of the sampling and analysis protocol will help ensure the accuracy and reliability of Method 5G emission-testing results.

Synergetic hydrothermal co-liquefaction of crude glycerol and aspen wood

DEFF Research Database (Denmark)

Pedersen, Thomas Helmer; Jasiunas, Lukas; Casamassima, Luca

2015-01-01

quality were all invariant to the reaction temperature. By increasing the crude glycerol to aspen wood mass ratio from 0:1 to 3:1, char yield was decreased from 18.3% (only aspen wood) to 3.4%. Furthermore, the biocrude quality in terms of the effective hydrogen-to-carbon ratio (H/Ceff) was significantly...

Wood pellets for stoker burner

International Nuclear Information System (INIS)

Nykaenen, S.

2000-01-01

The author of this article has had a stoker for several years. Wood chips and sod peat has been used as fuels in the stoker, either separately or mixed. Last winter there occurred problems with the sod peat due to poor quality. Wood pellets, delivered by Vapo Oy were tested in the stoker. The price of the pellets seemed to be a little high 400 FIM/500 kg large sack. If the sack is returned in good condition 50 FIM deposit will be repaid to the customer. However, Vapo Oy informed that the calorific value of wood pellets is three times higher than that of sod peat so it should not be more expensive than sod peat. When testing the wood pellets in the stoker, the silo of the stoker was filled with wood pellets. The adjustments were first left to position used for sod peat. However, after the fire had ignited well, the adjustments had to be decreased. The content of the silo was combusted totally. The combustion of the content of the 400 litter silo took 4 days and 22 hours. Respectively combustion of 400 l silo of good quality sod peat took 2 days. The water temperature with wood pellets remained at 80 deg C, while with sod peat it dropped to 70 deg C. The main disadvantage of peat with small loads is the unhomogenous composition of the peat. The results of this test showed that wood pellets will give better efficiency than peat, especially when using small burner heads. The utilization of them is easier, and the amount of ash formed in combustion is significantly smaller than with peat. Wood pellets are always homogenous and dry if you do not spoil it with unproper storage. Pellets do not require large storages, the storage volume needed being less than a half of the volume needed for sod peat. When using large sacks the amount needed can even be transported at the trunk of a passenger car. Depending on the area to be heated, a large sack is sufficient for heating for 2-3 weeks. Filling of stoker every 2-5 day is not an enormous task

IDEAS, for integral logistics in centralized wood processing

NARCIS (Netherlands)

Reinders, M.P.

1989-01-01

A decision support system (DSS) is developed to improve the quality of decision making in wood processing companies. Wood processing companies are businesses that import (buy, harvest) raw materials, stems and logs, and export (deliver) products, assortments and boards, after a multi-step

Wood handbook : wood as an engineering material

Science.gov (United States)

Robert J. Ross; Forest Products Laboratory. USDA Forest Service.

2010-01-01

Summarizes information on wood as an engineering material. Presents properties of wood and wood-based products of particular concern to the architect and engineer. Includes discussion of designing with wood and wood-based products along with some pertinent uses.

Wood waste in Europe

Energy Technology Data Exchange (ETDEWEB)

Matos, O; Ribeiro, R [Biomass Centre for Energy - CBE, Miranda do Corvo (Portugal)

1998-12-31

The energy policy of the EC, as well as most of member states points to a sizeable increase of energy production based on renewable energy sources, wood, wood residues, agricultural residues, energy crops including SRF, organic sludges, solid residues, etc. Most recent goals indicate a desirable duplication of today`s percentage by 2010. The reasons for this interest, besides diversification of sources, less dependence on imported fuels, use of endogenous resources, expected decrease of fossil fuel reserves, use of available land, additional employment and income for rural communities, etc., are related to important environmental benefits namely in terms of emissions of hot house gases. Wood waste, resulting from forest operations, cleaning, cultural and final cuttings, and from wood based industries, constitute a special important resource by reason of quality and availability. In addition to this they do not require additional land use and the removal is beneficial. In the run-up to the becoming December`s 1997 `Climate Change Summit` in Kioto, there is mounting pressure on companies to plan on carbon cuts. (author) 6 refs., 1 tab.

Wood waste in Europe

Energy Technology Data Exchange (ETDEWEB)

Matos, O.; Ribeiro, R. [Biomass Centre for Energy - CBE, Miranda do Corvo (Portugal)

1997-12-31

The energy policy of the EC, as well as most of member states points to a sizeable increase of energy production based on renewable energy sources, wood, wood residues, agricultural residues, energy crops including SRF, organic sludges, solid residues, etc. Most recent goals indicate a desirable duplication of today`s percentage by 2010. The reasons for this interest, besides diversification of sources, less dependence on imported fuels, use of endogenous resources, expected decrease of fossil fuel reserves, use of available land, additional employment and income for rural communities, etc., are related to important environmental benefits namely in terms of emissions of hot house gases. Wood waste, resulting from forest operations, cleaning, cultural and final cuttings, and from wood based industries, constitute a special important resource by reason of quality and availability. In addition to this they do not require additional land use and the removal is beneficial. In the run-up to the becoming December`s 1997 `Climate Change Summit` in Kioto, there is mounting pressure on companies to plan on carbon cuts. (author) 6 refs., 1 tab.

WOOD PROPERTIES AND EFFECT OF WOOD PROPERTIES ON THE WOOD FINISHING

Directory of Open Access Journals (Sweden)

Abdulkadir Malkoçoğlu

2006-04-01

Full Text Available Wood is basic raw material for furniture and joinery industries with wood structures. Wood is a biological material that has widely different properties depending on species, geographic area where the tree grew, the growth condition, size of the tree at harvest, sawing, and other manufacturing processes. Wood properties have been characterized within two groups as natural and manufacturing factors that effects finishing performance. Grow rate, density, knots, moisture content, extractives and juvenile wood are natural characteristics. Grain orientation, texture, drying and performance expectations are manufacturing characteristics. In this review, the effects of natural and manufacturing characteristics are discussed on the surface finishing performance of wood.

Wood and Sediment Dynamics in River Corridors

Science.gov (United States)

Wohl, E.; Scott, D.

2015-12-01

Large wood along rivers influences entrainment, transport, and storage of mineral sediment and particulate organic matter. We review how wood alters sediment dynamics and explore patterns among volumes of instream wood, sediment storage, and residual pools for dispersed pieces of wood, logjams, and beaver dams. We hypothesized that: volume of sediment per unit area of channel stored in association with wood is inversely proportional to drainage area; the form of sediment storage changes downstream; sediment storage correlates most strongly with wood load; and volume of sediment stored behind beaver dams correlates with pond area. Lack of data from larger drainage areas limits tests of these hypotheses, but analyses suggest a negative correlation between sediment volume and drainage area and a positive correlation between wood and sediment volume. The form of sediment storage in relation to wood changes downstream, with wedges of sediment upstream from jammed steps most prevalent in small, steep channels and more dispersed sediment storage in lower gradient channels. Use of a published relation between sediment volume, channel width, and gradient predicted about half of the variation in sediment stored upstream from jammed steps. Sediment volume correlates well with beaver pond area. Historically more abundant instream wood and beaver populations likely equated to greater sediment storage within river corridors. This review of the existing literature on wood and sediment dynamics highlights the lack of studies on larger rivers.

Management alternatives of energy wood thinning stands

International Nuclear Information System (INIS)

Heikkilae, Jani; Siren, Matti; Aeijaelae, Olli

2007-01-01

Energy wood thinning has become a feasible treatment alternative of young stands in Finland. Energy wood thinnings have been carried out mainly in stands where precommercial thinning has been neglected and the harvesting conditions for industrial wood thinning are difficult. Despite of its positive effects on harvesting costs and on renewable energy potential, whole-tree harvesting has been constantly criticized for causing growth loss. In this paper, the profitability of energy wood thinning was studied in 20 Scots pine-dominated stands where energy wood thinning was carried out. The growth of the stands after thinning was predicted with the help of Motti-stand simulator. Entire rotation time of the stands was simulated with different management alternatives. The intensity of first thinning and recovery level of logging residues varied between alternatives. In order to attain acceptable harvesting conditions, industrial wood thinning had to be delayed. The effect of energy wood thinning on subsequent stem wood growth was almost the same as in conventional thinning. Whole-tree harvesting for energy proved to be profitable alternative if the stumpage price is around 3EUR m -3 , the interest rate is 3% or 5% and the removal of pulpwood is less than 20 m 3 ha -1 . If the harvestable pulpwood yield is over 20 m 3 ha -1 , integrated harvesting of industrial and energy wood or delayed industrial wood harvesting becomes more profitable. (author)

Wood-energy - The sector get worried

International Nuclear Information System (INIS)

Mary, Olivier; Signoret, Stephane; Bohlinger, Philippe; Guilhem, Jean; De Santis, Audrey; Sredojevic, Alexandre; Defaye, Serge; Maindrault, Marc

2017-01-01

Wood energy is, today and certainly also tomorrow, one of the most important renewable energies in France. However, the wood-energy sector seems to slow down as hydrocarbon prices stay extremely low. This document presents 8 articles, describing the context and the characteristics of this evolution, plus some examples of developments in France. The themes of the articles are: the activity of the wood-energy sector should be reinforced to meet the objectives of the French energy multi-year plan; The 2035 prospective of the wood yield in the French forest will meet the future demand, however this evaluation does not take into consideration the effects of the climatic change; the conversion to biomass of the 'Fort de l'Est' (near Paris) heating system (equipped with a boiling fluidized bed boiler) has enabled the heat network to beat the 50 pc share of renewable energy; wood-energy professionals use the 'quality' lever to challenge their fossil fuel competitors; the city of Orleans is now equipped with an innovative biomass cogeneration plant; the example of wood waste valorization in a French sawmill; the French ONF (Forest Administration) Wood-Energy actor has just inaugurated its largest biomass dryer, in order to develop the domestic market for wood as a fuel; analysis of the technical and economical feasibility of using wood to generate electric power or replacing electric space heating by heat network

Preservation of forest wood chips

Energy Technology Data Exchange (ETDEWEB)

Kofman, P.D.; Thomsen, I.M.; Ohlsson, C.; Leer, E.; Ravn Schmidt, E.; Soerensen, M.; Knudsen, P.

1999-01-01

As part of the Danish Energy Research Programme on biomass utilisation for energy production (EFP), this project concerns problems connected to the handling and storing of wood chips. In this project, the possibility of preserving wood chips of the Norway Spruce (Picea Abies) is addressed, and the potential improvements by anaerobic storage are tested. Preservation of wood chips aims at reducing dry matter losses from extensive heating during storage and to reduce production of fungal spores. Fungal spores pose a health hazards to workers handling the chips. Further the producers of wood chips are interested in such a method since it would enable them to give a guarantee for the delivery of homogeneous wood chips also during the winter period. Three different types of wood chips were stored airtight and further one of these was stored in accordance with normal practise and use as reference. The results showed that airtight storage had a beneficial impact on the quality of the chips: no redistribution of moisture, low dry matter losses, unfavourable conditions for microbial activity of most fungi, and the promotion of yeasts instead of fungi with airborne spores. Likewise the firing tests showed that no combustion problems, and no increased risk to the environment or to the health of staff is caused by anaerobic storage of wood chips. In all, the tests of the anaerobic storage method of forest wood chips were a success and a large-scale test of the method will be carried out in 1999. (au)

Volume loss as a tool to assess kiln drying of eucalyptus wood

Directory of Open Access Journals (Sweden)

Djeison Cesar Batista

Full Text Available In this study, we aimed to analyze the kiln drying quality of Eucalyptus grandis, Eucalyptus saligna and Eucalyptus dunnii woods with respect to volume loss. Wood from the three species was kiln dried together with the same drying schedule and conditions in a conventional-temperature pilot kiln. Three kinds of volume loss were evaluated: total - from saturated (initial to machined (final condition; shrinkage - from saturated to 10% moisture content; and machining - from 10% moisture content to machined condition. Eucalyptus grandis wood was the most dimensionally stable and presented the smallest volume loss due to shrinkage. Although they had different shrinkage behaviors, Eucalyptus grandis and Eucalyptus saligna woods presented the same drying quality regarding machining and total volume losses. These species can be considered the same for kiln drying. Eucalyptus dunnii wood presented the worst quality in drying, and should not be kiln dried in the same batch with the other species.

In situ high-temperature gas sensors: continuous monitoring of the combustion quality of different wood combustion systems and optimization of combustion process

Directory of Open Access Journals (Sweden)

H. Kohler

2018-03-01

Full Text Available The sensing characteristics and long-term stability of different kinds of CO ∕ HC gas sensors (non-Nernstian mixed potential type during in situ operation in flue gas from different types of low-power combustion systems (wood-log- and wood-chip-fuelled were investigated. The sensors showed representative but individual sensing behaviour with respect to characteristically varying flue gas composition over the combustion process. The long-term sensor signal stability evaluated by repeated exposure to CO ∕ H2 ∕ N2 ∕ synthetic air mixtures showed no sensitivity loss after operation in the flue gas. Particularly for one of the sensors (Heraeus GmbH, this high signal stability was observed in a field test experiment even during continuous operation in the flue gas of the wood-chip firing system over 4 months. Furthermore, it was experimentally shown that the signals of these CO ∕ HC sensing elements yield important additional information about the wood combustion process. This was demonstrated by the adaptation of an advanced combustion airstream control algorithm on a wood-log-fed fireplace and by the development of a combustion quality monitoring system for wood-chip-fed central heaters.

Comparative study of Danish prefab houses made of wood

DEFF Research Database (Denmark)

Wraber, Ida Kristina

2011-01-01

The use of wood in Danish prefab building projects is increasing, but there is not a strong architectural tradition in Denmark for constructing timber housing. This paper therefore contains a comparative study of various manners of incorporating architectural features in prefab houses made of wood....... In the study four Danish prefab housing concepts based on wood con¬struc¬tion is compared and discussed, in order to investigate and exemplify how it is possible to work with architectural quality in prefab timber housing and maximise the use of the material, the prefab production and the architectural values....... It was concluded that especially two aspects are of great importance for the concrete handling of the architectural quality of prefab houses made of wood; 1) flexibility in relation to user and site, and 2) the interaction between form, logics and material. It is suggested that keeping these two aspects in mind...

Wood : adhesives

Science.gov (United States)

A.H. Conner

2001-01-01

This chapter on wood adhesives includes: 1) Classification of wood adhesives 2) Thermosetting wood adhesives 3) Thermoplastic adhesives, 4) Wood adhesives based on natural sources 5) Nonconventional bonding of wood 6) Wood bonding.

Climate fails to predict wood decomposition at regional scales

Czech Academy of Sciences Publication Activity Database

Bradford, M.A.; Warren, R.J.; Baldrian, Petr; Crowther, T. W.; Maynard, D.S.; Oldfield, E.E.; Wieder, W.R.; Wood, S.A.; King, J.R.

2014-01-01

Roč. 4, č. 7 (2014), s. 625-630 ISSN 1758-678X Institutional support: RVO:61388971 Keywords : ecosystem * climate changes * wood decomposition * forest Subject RIV: EE - Microbiology, Virology Impact factor: 14.547, year: 2014

Pelly Crossing wood chip boiler

Energy Technology Data Exchange (ETDEWEB)

1985-03-11

The Pelly wood chip project has demonstrated that wood chips are a successful fuel for space and domestic water heating in a northern climate. Pelly Crossing was chosen as a demonstration site for the following reasons: its extreme temperatures, an abundant local supply of resource material, the high cost of fuel oil heating and a lack of local employment. The major obstacle to the smooth operation of the boiler system was the poor quality of the chip supply. The production of poor quality chips has been caused by inadequate operation and maintenance of the chipper. Dull knives and faulty anvil adjustments produced chips and splinters far in excess of the one centimetre size specified for the system's design. Unanticipated complications have caused costs of the system to be higher than expected by approximately $15,000. The actual cost of the project was approximately $165,000. The first year of the system's operation was expected to accrue $11,600 in heating cost savings. This estimate was impossible to confirm given the system's irregular operation and incremental costs. Consistent operation of the system for a period of at least one year plus the installation of monitoring devices will allow the cost effectiveness to be calculated. The wood chip system's impact on the environment was estimated to be minimal. Wood chip burning was considered cleaner and safer than cordwood burning. 9 refs., 6 figs., 6 tabs.

The use of wood for wind turbine blade construction

Science.gov (United States)

Gougeon, M.; Zuteck, M.

1979-01-01

The interrelationships between moisture and wood, conditions for dry rot spore activity, the protection of wood fibers from moisture, wood resin composites, wood laminating, quality control, and the mechanical properties of wood are discussed. The laminated veneer and the bonded sawn stock fabrication techniques, used in the construction of a turbine blade with a monocoque 'D' section forming the leading edge and a built up trailing edge section, are described. A 20 foot root end sample complete with 24 bonded-in studs was successfully subjected to large onetime loads in both the flatwise and edgewise directions, and to fatigue tests. Results indicate that wood is both a viable and advantageous material for use in wind turbine blades. The basic material is reasonably priced, domestically available, ecologically sound, and easily fabricated with low energy consumption.

Mechanics of the Compression Wood Response: II. On the Location, Action, and Distribution of Compression Wood Formation.

Science.gov (United States)

Archer, R R; Wilson, B F

1973-04-01

A new method for simulation of cross-sectional growth provided detailed information on the location of normal wood and compression wood increments in two tilted white pine (Pinus strobus L.) leaders. These data were combined with data on stiffness, slope, and curvature changes over a 16-week period to make the mechanical analysis. The location of compression wood changed from the under side to a flank side and then to the upper side of the leader as the geotropic stimulus decreased, owing to compression wood action. Its location shifted back to a flank side when the direction of movement of the leader reversed. A model for this action, based on elongation strains, was developed and predicted the observed curvature changes with elongation strains of 0.3 to 0.5%, or a maximal compressive stress of 60 to 300 kilograms per square centimeter. After tilting, new wood formation was distributed so as to maintain consistent strain levels along the leaders in bending under gravitational loads. The computed effective elastic moduli were about the same for the two leaders throughout the season.

How the climate limits the wood density of angiosperms

Science.gov (United States)

Choi, Jin Woo; Kim, Ho-Young

2017-11-01

Flowering trees have various types of wood structure to perform multiple functions under their environmental conditions. In addition to transporting water from the roots to the canopy and providing mechanical support, the structure should provide resistance to embolism to maintain soil-plant-atmosphere continuum. By investigating existing data of the resistivity to embolism and wood density of 165 angiosperm species, here we show that the climate can limit the intrinsic properties of trees. Trees living in the dry environments require a high wood density to slow down the pressure decrease as it loses water relatively fast by evaporation. However, building too much tissues will result in the decrease of hydraulic conductivity and moisture concentration around mesophyll cells. To rationalize the biologically observed lower bound of the wood density, we construct a mechanical model to predict the wood density as a function of the vulnerability to embolism and the time for the recovery. Also, we build an artificial system using hydrogel microchannels that can test the probability of embolism as a function of conduit distributions. Our theoretical prediction is shown to be consistent with the results obtained from the artificial system and the biological data.

Rehabilitating agricultural streams in Australia with wood: a review.

Science.gov (United States)

Lester, Rebecca E; Boulton, Andrew J

2008-08-01

Worldwide, the ecological condition of streams and rivers has been impaired by agricultural practices such as broadscale modification of catchments, high nutrient and sediment inputs, loss of riparian vegetation, and altered hydrology. Typical responses include channel incision, excessive sedimentation, declining water quality, and loss of in-stream habitat complexity and biodiversity. We review these impacts, focusing on the potential benefits and limitations of wood reintroduction as a transitional rehabilitation technique in these agricultural landscapes using Australian examples. In streams, wood plays key roles in shaping velocity and sedimentation profiles, forming pools, and strengthening banks. In the simplified channels typical of many agricultural streams, wood provides habitat for fauna, substrate for biofilms, and refuge from predators and flow extremes, and enhances in-stream diversity of fish and macroinvertebrates.Most previous restoration studies involving wood reintroduction have been in forested landscapes, but some results might be extrapolated to agricultural streams. In these studies, wood enhanced diversity of fish and macroinvertebrates, increased storage of organic material and sediment, and improved bed and bank stability. Failure to meet restoration objectives appeared most likely where channel incision was severe and in highly degraded environments. Methods for wood reintroduction have logistical advantages over many other restoration techniques, being relatively low cost and low maintenance. Wood reintroduction is a viable transitional restoration technique for agricultural landscapes likely to rapidly improve stream condition if sources of colonists are viable and water quality is suitable.

Sound quality prediction for engine-radiated noise

Science.gov (United States)

Liu, Hai; Zhang, Junhong; Guo, Peng; Bi, Fengrong; Yu, Hanzhengnan; Ni, Guangjian

2015-05-01

Diesel engine-radiated noise quality prediction is an important topic because engine noise has a significant impact on the overall vehicle noise. Sound quality prediction is based on subjective and objective evaluation of engine noise. The integrated satisfaction index (ISI) is proposed as a criterion for differentiate noise quality in the subjective evaluation, and five psychoacoustic parameters are selected for characterizing and analyzing the noise quality of the diesel engine objectively. The combination of support vector machines (SVM) and genetic algorithm (GA) is proposed in order to establish a model for predicting the diesel engine-radiated noise quality for all operation conditions. The performance of the GA-SVM model is compared with the BP neural network model, and the results show that the mean relative error of the GA-SVM model is smaller than the BP neural network model. The importance rank of the sound quality metrics to the ISI is indicated by the non-parametric correlation analysis. This study suggests that the GA-SVM model is very useful for accurately predicting the diesel engine-radiated noise quality.

Proceedings of the 8. biennial residual wood conference

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

This conference highlighted practical strategies for managing and utilizing residual wood as a true industry resource. Examples of successful wood energy projects were presented along with the technology and products of more than 30 companies involved in the residual wood business. The topics of discussion ranged from biomass supplies, quality issues, and harvesting guidelines to emerging biomass technologies, project overviews, and financing. The presentations outlined the many opportunities that exist for the forest industry to produce energy from biostock, such as healthy and diseased trees, underbrush, sawdust, wood chips, wood pulp and black liquor. Increasing fuel and energy costs along with advances in technology are improving the economy of forest-based biorefineries. The presentations showed how the industry can gain revenue from residual wood, which is steadily becoming a more valuable resource for pellet production and energy generation The conference featured 20 presentations, of which 3 have been catalogued separately for inclusion in this database. refs., tabs., figs.

PREDICTION AND ANALYSIS OF SLOVAKIAN TIMBER TRADE ON GLOBAL MARKET CONDITIONS

Directory of Open Access Journals (Sweden)

Miloš Gejdoš

2017-11-01

Full Text Available In Slovakian forestry the main source of finance is the wood sale. The main aim of this paper is to evaluate the assortments supply structure (quality management, prices development for the coniferous sawlogs and to set the future prediction of this development in new global market conditions, which are affected mainly by the global climate changes. Price changes were analysed for the period of the years from 2000 to March 2016 for the spruce and fir sawlogs. Data about the volume supply of raw-wood assortments in Slovakia for years 2005-2014 were collected from “Green Reports“ published by the Ministry of Agriculture and Rural Development of the Slovak Republic. From the influence factors in the studied period, the biggest impact was assigned to the global economic crisis. The prediction captures the further decline of prices of raw-wood assortments. In the second half of the year 2016 the price of sawlogs decreased by € 4 per 1 m3. Local impacts, the structure of wood processors and specific trade area in Slovakia affected substantially the structure of assortments on Market. There is also some space for a better evaluation of harvested wood.

Airborne sound transmission loss characteristics of wood-frame construction

Science.gov (United States)

Rudder, F. F., Jr.

1985-03-01

This report summarizes the available data on the airborne sound transmission loss properties of wood-frame construction and evaluates the methods for predicting the airborne sound transmission loss. The first part of the report comprises a summary of sound transmission loss data for wood-frame interior walls and floor-ceiling construction. Data bases describing the sound transmission loss characteristics of other building components, such as windows and doors, are discussed. The second part of the report presents the prediction of the sound transmission loss of wood-frame construction. Appropriate calculation methods are described both for single-panel and for double-panel construction with sound absorption material in the cavity. With available methods, single-panel construction and double-panel construction with the panels connected by studs may be adequately characterized. Technical appendices are included that summarize laboratory measurements, compare measurement with theory, describe details of the prediction methods, and present sound transmission loss data for common building materials.

Age trends and within-site effects in wood density and radial growth in Quercus faginea mature trees

Directory of Open Access Journals (Sweden)

Vicelina B. Sousa

2016-04-01

Full Text Available Aim of the study: This paper aims to valorize the wood of Quercus faginea Lam. for high quality end uses (e.g. furniture by studying growth and quality properties using mature trees. Age trends in tree-ring width and wood density are shown and the main factors responsible for variations in tree-ring width and wood density within and between trees are investigated. Area of study: The study site is in the center of Portugal within the natural species distribution area.Material and methods: Radial samples from ten mature trees were collected at 6 heights (from base to 9.7 m and prepared for X-ray microdensity.Main results: Wood density showed high values, ranging from 0.868 g/cm3 to 0.957 g/cm3. Wood density decreased from pith to bark and with stem height. Cambial age showed a linear relationship with wood density and most of the variation in wood is explained by age. Intra-ring and axial within-tree homogeneity was good.Research highlights: Mature trees of Q. faginea showed high wood density and a high potential for high quality end uses, comparable to other oaks. Wood density is influenced by cambial age and tree-ring width. Wood quality may be improved by tree growth rates adjustment e.g. through an adequate tree stand density (e.g. thinning operations. 

Age trends and within-site effects in wood density and radial growth in Quercus faginea mature trees

Energy Technology Data Exchange (ETDEWEB)

Sousa, V.B.; Louzada, J.L.; Pereira, H.

2016-07-01

Aim of study: This paper aims to valorize the wood of Quercus faginea Lam. for high quality end uses (e.g. furniture) by studying growth and quality properties using mature trees. Age trends in tree-ring width and wood density are shown and the main factors responsible for variations in tree-ring width and wood density within and between trees are investigated. Area of study: The study site is in the center of Portugal within the natural species distribution area. Material and methods: Radial samples from ten mature trees were collected at 6 heights (from base to 9.7 m) and prepared for X-ray microdensity. Main results: Wood density showed high values, ranging from 0.868 g/cm3 to 0.957 g/cm3. Wood density decreased from pith to bark and with stem height. Cambial age showed a linear relationship with wood density and most of the variation in wood is explained by age. Intra-ring and axial within-tree homogeneity was good. Research highlights: Mature trees of Q. faginea showed high wood density and a high potential for high quality end uses, comparable to other oaks. Wood density is influenced by cambial age and tree-ring width. Wood quality may be improved by tree growth rates adjustment e.g. through an adequate tree stand density (e.g. thinning operations). (Author)

Age trends and within-site effects in wood density and radial growth in Quercus faginea mature trees

International Nuclear Information System (INIS)

Sousa, V.B.; Louzada, J.L.; Pereira, H.

2016-01-01

Aim of study: This paper aims to valorize the wood of Quercus faginea Lam. for high quality end uses (e.g. furniture) by studying growth and quality properties using mature trees. Age trends in tree-ring width and wood density are shown and the main factors responsible for variations in tree-ring width and wood density within and between trees are investigated. Area of study: The study site is in the center of Portugal within the natural species distribution area. Material and methods: Radial samples from ten mature trees were collected at 6 heights (from base to 9.7 m) and prepared for X-ray microdensity. Main results: Wood density showed high values, ranging from 0.868 g/cm3 to 0.957 g/cm3. Wood density decreased from pith to bark and with stem height. Cambial age showed a linear relationship with wood density and most of the variation in wood is explained by age. Intra-ring and axial within-tree homogeneity was good. Research highlights: Mature trees of Q. faginea showed high wood density and a high potential for high quality end uses, comparable to other oaks. Wood density is influenced by cambial age and tree-ring width. Wood quality may be improved by tree growth rates adjustment e.g. through an adequate tree stand density (e.g. thinning operations). (Author)

Biophysical modelling of intra-ring variations in tracheid features and wood density of Pinus pinaster trees exposed to seasonal droughts.

Science.gov (United States)

Wilkinson, Sarah; Ogée, Jérôme; Domec, Jean-Christophe; Rayment, Mark; Wingate, Lisa

2015-03-01

Process-based models that link seasonally varying environmental signals to morphological features within tree rings are essential tools to predict tree growth response and commercially important wood quality traits under future climate scenarios. This study evaluated model portrayal of radial growth and wood anatomy observations within a mature maritime pine (Pinus pinaster (L.) Aït.) stand exposed to seasonal droughts. Intra-annual variations in tracheid anatomy and wood density were identified through image analysis and X-ray densitometry on stem cores covering the growth period 1999-2010. A cambial growth model was integrated with modelled plant water status and sugar availability from the soil-plant-atmosphere transfer model MuSICA to generate estimates of cell number, cell volume, cell mass and wood density on a weekly time step. The model successfully predicted inter-annual variations in cell number, ring width and maximum wood density. The model was also able to predict the occurrence of special anatomical features such as intra-annual density fluctuations (IADFs) in growth rings. Since cell wall thickness remained surprisingly constant within and between growth rings, variations in wood density were primarily the result of variations in lumen diameter, both in the model and anatomical data. In the model, changes in plant water status were identified as the main driver of the IADFs through a direct effect on cell volume. The anatomy data also revealed that a trade-off existed between hydraulic safety and hydraulic efficiency. Although a simplified description of cambial physiology is presented, this integrated modelling approach shows potential value for identifying universal patterns of tree-ring growth and anatomical features over a broad climatic gradient. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Development of a residential wood smoke reduction plan in a wood burning community: A case study in Libby, Montana

International Nuclear Information System (INIS)

Fox, R.J.; Manderino, L.; Lyons, C.E.; Morris, A.L.; Anderson, R.L.

1992-01-01

Libby, Montana depends on wood as a heating fuel. Libby exceeded the 24-hour federal PM10 ambient air quality standard every year since monitoring began in 1987. Residential wood smoke significantly contributes to its air pollution. To decrease residential wood smoke's contribution to air pollution, residents have to modify their heating habits. County officials sponsored the development of a comprehensive community-oriented plan to reduce wood smoke. This paper describes how the plan was developed and the components of the air pollution reduction strategies. The plan was developed using community input and tailored to local conditions. Four specific strategies were developed to reduce residential wood smoke pollution. Development of strategies required analysis of home heating habits and potential alternatives. Economic conditions were also considered. Expensive control strategies would be worthless unless alternative funding methods were provided. Thus, the plan included an array of funding sources to facilitate implementation. The development and implementation techniques are applicable to other communities with similar air pollution challenges

A gauge for the measurement of wood density MGD-05

International Nuclear Information System (INIS)

Bartak, J.; Machaj, B.; Urbanski, P.; Pienkos, P.

2006-01-01

Wood density is an important parameter determining several properties of wood as: wood quality, mechanical resistance, charcoal production, transport cost, etc. Radiometric methods for the measurement of wood density are based on attenuation of 241 Am gamma radiation, or measurement of backscattered 241 Am radiation. In the paper authors describe the newly constructed computerized gauge designed for the non routine measurements. Up to 1000 measuring results can be stored in the gauge memory and the measuring results can be sent to an external laptop for computations of density contours

Impact of initial spacing on yield per acre and wood quality of unthinned loblolly pine at age 21

Science.gov (United States)

Alexander, III Clark; Richard F. Daniels; Lewis Jordan; Laurie Schimleck

2010-01-01

The market for southern pine first thinnings is soft. Thus, forest managers are planting at wider spacings, and using weed control and fertilization to grow chipping-saw and sawtimber trees in shorter rotations. A 21-year-old unthinned spacing study was sampled to determine the effect of initial spacing on wood quality and yield per acre of planted loblolly pine (

Respiratory symptoms and lung function in relation to wood dust and monoterpene exposure in the wood pellet industry.

Science.gov (United States)

Löfstedt, Håkan; Hagström, Katja; Bryngelsson, Ing-Liss; Holmström, Mats; Rask-Andersen, Anna

2017-06-01

Wood pellets are used as a source of renewable energy for heating purposes. Common exposures are wood dust and monoterpenes, which are known to be hazardous for the airways. The purpose of this study was to study the effect of occupational exposure on respiratory health in wood pellet workers. Thirty-nine men working with wood pellet production at six plants were investigated with a questionnaire, medical examination, allergy screening, spirometry, and nasal peak expiratory flow (nasal PEF). Exposure to wood dust and monoterpenes was measured. The wood pellet workers reported a higher frequency of nasal symptoms, dry cough, and asthma medication compared to controls from the general population. There were no differences in nasal PEF between work and leisure time. A lower lung function than expected (vital capacity [VC], 95%; forced vital capacity in 1 second [FEV 1 ], 96% of predicted) was noted, but no changes were noted during shifts. There was no correlation between lung function and years working in pellet production. Personal measurements of wood dust at work showed high concentrations (0.16-19 mg/m 3 ), and exposure peaks when performing certain work tasks. Levels of monoterpenes were low (0.64-28 mg/m 3 ). There was no association between exposure and acute lung function effects. In this study of wood pellet workers, high levels of wood dust were observed, and that may have influenced the airways negatively as the study group reported upper airway symptoms and dry cough more frequently than expected. The wood pellet workers had both a lower VC and FEV 1 than expected. No cross-shift changes were found.

Production of dry wood chips in connection with a district heating plant

Directory of Open Access Journals (Sweden)

Yrjölä Jukka

2004-01-01

Full Text Available Moisture and its variation in wood chips make the control of burning in small scale heating appliances difficult resulting in emissions and loss of efficiency. If the quality of wood chips would be better, i. e. dried and sieved fuel with more uniform size distribution would be avail able, the burning could be much cleaner and efficiency higher. In addition higher power out put could be obtained and the investment costs of the burning appliances would be lower. The production of sieved and dried wood chip with good quality could be accomplished in connection with a district heating plant. Then the plant would make profit, in addition to the district heat, from the dried wood chips sold to the neighboring buildings and enterprises sep a rated from the district heating net using wood chips in energy production. The peak power of a district heating plant is required only a short time during the coldest days of the winter. Then the excess capacity during the milder days can be used as heat source for drying of wood chips to be marketed. Then wood chips are sieved and the fuel with best quality is sold and the reject is used as fuel in the plant it self. In a larger district heating plant, quality of the fuel does not need to be so high In this paper the effect of moisture on the fuel chain and on the boiler is discussed. Energy and mass balance calculations as a tool of system design is described and the characteristics of proposed dry chips production method is discussed.

Wood anatomical and chemical properties related to the pulpability ...

African Journals Online (AJOL)

Eucalyptus globulus is one of the most important hardwood species used by the pulp and paper industry due to its high pulp yield, high wood density, excellent fibre quality and good handsheet properties. However, the wood is a highly variable and complex material that has different chemical, physical and anatomical ...

Programme wood/energy 2000-2006. Activity Report for 2000-2004

International Nuclear Information System (INIS)

2006-01-01

When ADEME launched its Wood fuel programme throughout all of France in late 1999, its aim was to guide this resource supply chain to maturity and stable development in all user sectors: domestic, multi-family housing, commercial/institutional and industrial applications. To this end the Wood fuel Programme 2000-2006 was assigned objectives and endowed with significant financial means for studies and coordination in order to support and carry out general-interest projects, piloted by ADEME. The stated goal was to replace fossil fuels, avoid carbon emissions and establish quality assurance standards for household firewood and wood-fired devices. This report makes a status of ADEME's Wood fuel programme for the 2000-2004 era: - Domestic heating: After a drop during the 1990's, figures since 1999 of sales of wood-fuel domestic heating equipment (closed heaters, glass-door fires and stoves) have shown a significant rise. On average over 30 years, wood consumption has risen to 7.2 million TOE (40 million cubic metres) per year; - Industry: It is thought there are 1000 wood-fired heaters (above 1 megawatt) used in French industry. These are found mainly in timber-based industries and in timber crushing plants. This amounts to a total power output of 2.5 gigawatts. In the primary and secondary wood processing industries, the increase in the number of wood-fired boilers and energy produced has reached 5% per year Results of a call for carbon energy projects (APEC) was 61 submitted of which 52 were selected; 9 projects pending (166.5 K of aid from ADEME); and 35 projects begun (1,649 K of aid from ADEME). - Local authority and service sector wood-fired heating systems: At the end of 2004, the number of local authority active boilers was 641, producing 430 megawatts. This is an increase of an average of 13% year on year since 2000. By the end of 2004, the target had already been met for the number of boilers being financed (1,090). By 2006 however we still need to generate a

Improvement of wood quality used in Syria by irradiation polymerization

International Nuclear Information System (INIS)

Bakarji, E. H.

2002-06-01

Wood plastic composites (WPC) have been prepared with five low-grade woods, native to Syria, and with Okoume (aucoumea klaineana pierre) imported to Syria in large quantities. Three monomer systems; acrylamide, butylmethacrylate, and styrene were used. polymerization was induced at various radiation doses (10, 20, and 30 kGy) to study the role of radiation doses using a 60 Co gamma radiation source. Some physical properties of WPC, namely polymer loading and compression strength or tensile strength of the obtained wood polymer composites (WPC) were studied. The effect of the additives, sulfuric acid (H + ), N-vinyl pyrrolidone (NVP), trimethyolpropane triacrylate (TMPTA), urea (U), lithium nitrate (LiNo 3 ), copper sulfate (CuSO 4 ) and co-additives on monomer system polymerization were also investigated. Methanol, water and water/methanol mixtures were used as the swelling agents. In general, the use of additives and co-additives brought about an enhancement of tensile strength or compression strength and polymer loading of the composites. In some cases, additives also lowered the monomer concentration and the gamma radiation dose required for polymerization (author)

Landsat Time-series for the Masses: Predicting Wood Biomass Growth from Tree-rings Using Departures from Mean Phenology in Google Earth Engine

Science.gov (United States)

Foster, J. R.; D'Amato, A. W.; Itter, M.; Reinikainen, M.; Curzon, M.

2017-12-01

The terrestrial carbon cycle is perturbed when disturbances remove leaf biomass from the forest canopy during the growing season. Changes in foliar biomass arise from defoliation caused by insects, disease, drought, frost or human management. As ephemeral disturbances, these often go undetected and their significance to models that predict forest growth from climatic drivers remains unknown. Here, we seek to distinguish the roles of weather vs. canopy disturbance on forest growth by using dense Landsat time-series to quantify departures in mean phenology that in turn predict changes in leaf biomass. We estimated a foliar biomass index (FBMI) from 1984-2016, and predict plot-level wood growth over 28 years on 156 tree-ring monitoring plots in Minnesota, USA. We accessed the entire Landsat archive (sensors 4, 5 & 7) to compute FBMI using Google Earth Engine's cloud computing platform (GEE). GEE allows this pixel-level approach to be applied at any location; a feature we demonstrate with published wood-growth data from flux tower sites. Our Bayesian models predicted biomass changes from tree-ring plots as a function of Landsat FBMI and annual climate data. We expected model parameters to vary by tree functional groups defined by differences in xylem anatomy and leaf longevity, two traits with linkages to phenology, as reported in a recent review. We found that Landsat FBMI was a surprisingly strong predictor of aggregate wood-growth, explaining up to 80% of annual growth variation for some deciduous plots. Growth responses to canopy disturbance varied among tree functional groups, and the importance of some seasonal climate metrics diminished or changed sign when FBMI was included (e.g. fall and spring climatic water deficit), while others remained unchanged (current and lagged summer deficit). Insights emerging from these models can clear up sources of persistent uncertainty and open a new frontier for models of forest productivity.

Integrated energy wood and pulpwood harvesting in first-thinning stands

Energy Technology Data Exchange (ETDEWEB)

Kaerhae, K.; Pajuoja, H. (Metsaeteho Oy, Helsinki (Finland)), Email: kalle.karha@metsateho.fi, Email: heikki.pajuoja@metsateho.fi; Hoegnaes, T. (Metsaehallitus, Kajaani (Finland)), Email: tore.hognas@metsa.fi; Mutikainen, A. (TTS Research, Rajamaeki (Finland)), Email: arto.mutikainen@tts.fi

2009-07-01

The integrated harvesting of industrial roundwood and energy wood by the so-called 'two-pile cutting method' has increased strongly in young forests in Finland during the last two years. The studies carried out by Metsaeteho Oy, Metsaehallitus and TTS Research (I) determined the time consumption and productivity in cutting work when using the integrated cutting of first-thinning wood, (II) clarified the development of the total removal in integrated harvesting operation, and (III) investigated the quality of pulpwood poles when using integrated the quality of pulpwood poles when using integrated cutting with multi-tree handling. The studies indicated that the total removal in integrated wood harvesting increases significantly compared to that of conventional, separate roundwood harvesting. When the total removal from the harvesting site increased considerably, there was a significant increase in the productivity of cutting work in integrated wood harvesting compared to the situation in separate pulpwood harvesting. In addition, the delimbing quality and bucking accuracy of the pulpwood poles obtained in multi-tree processing were comparable to those produced in single-tree handling. There were no problems with measuring the work output by a grapple scale attached to the boom of the forwarder. As the studies indicated very promising experiences in integrated wood cutting, integrated harvesting is likely to continue to increase in both first and later thinning in Finland. (orig.)

Video Quality Prediction over Wireless 4G

KAUST Repository

Lau, Chun Pong

2013-04-14

In this paper, we study the problem of video quality prediction over the wireless 4G network. Video transmission data is collected from a real 4G SCM testbed for investigating factors that affect video quality. After feature transformation and selection on video and network parameters, video quality is predicted by solving as regression problem. Experimental results show that the dominated factor on video quality is the channel attenuation and video quality can be well estimated by our models with small errors.

Video Quality Prediction over Wireless 4G

KAUST Repository

Lau, Chun Pong; Zhang, Xiangliang; Shihada, Basem

2013-01-01

In this paper, we study the problem of video quality prediction over the wireless 4G network. Video transmission data is collected from a real 4G SCM testbed for investigating factors that affect video quality. After feature transformation and selection on video and network parameters, video quality is predicted by solving as regression problem. Experimental results show that the dominated factor on video quality is the channel attenuation and video quality can be well estimated by our models with small errors.

Cord Wood Testing in a Non-Catalytic Wood Stove

Energy Technology Data Exchange (ETDEWEB)

Butcher, T. [Brookhaven National Lab. (BNL), Upton, NY (United States); Trojanowski, R. [Brookhaven National Lab. (BNL), Upton, NY (United States); Wei, G. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2014-06-30

EPA Method 28 and the current wood stove regulations have been in-place since 1988. Recently, EPA proposed an update to the existing NSPS for wood stove regulations which includes a plan to transition from the current crib wood fuel to cord wood fuel for certification testing. Cord wood is seen as generally more representative of field conditions while the crib wood is seen as more repeatable. In any change of certification test fuel, there are questions about the impact on measured results and the correlation between tests with the two different fuels. The purpose of the work reported here is to provide data on the performance of a noncatalytic stove with cord wood. The stove selected has previously been certified with crib wood which provides a basis for comparison with cord wood. Overall, particulate emissions were found to be considerably higher with cord wood.

Impacts of two improved wood-burning stoves on the indoor air quality

DEFF Research Database (Denmark)

Luis Teles de Carvalho, Ricardo; Jensen, Ole Michael; Tarelho, Luis A. C.

2014-01-01

Large amounts of forest wood is still being used in rural housing in low and mid-income countries in South America - 36% in Peru and 6% in Brazil - generating hazardous wood smoke. Interviews were conducted to the users of improved stoves in 20 rural households. In Peru, the field study was carri...

Partial debarking of energy wood stems in production of high quality fuel chips and fuel logs (DryMe); Runkopuun osittainen kuorinta metsaehakkeen ja pilkkeidentuotantoketjussa (DryMe) - PUUT58

Energy Technology Data Exchange (ETDEWEB)

Sikanen, L.; Roeser, D.; Tahvanainen, T.; Prinz, R. [Finnish Forest Research Institute, Joensuu (Finland); Erkkilae, A.; Heikkinen, A.; Hillebrand, K. [VTT Technical Research Centre of Finland, Jyvaeskylae (Finland)

2007-07-01

Small wood chip fueled heating plants require high quality chips in order to achieve low service need and problem free running. Low moisture content is considered to be the most important quality factor in wood based fuels. On the other hand, drying should be efficient and handy as a part of supply chain. Rapidly growing small-scale wood energy business needs new methods to ensure availability of high quality fuel. Partial debarking of both boreal broadleaved and coniferous species is known as effective method to dry timber during storing. Anyhow, proper place for storing and convenient weather conditions are needed. Partly debarked stems could be also the raw material for wood pellets. In Finnish studies, for example, storing over one summer took moisture content down from 40% to 27% with partly debarked birch logs. Some preliminary tests have been made also in Scotland and England with baled residues and small diameter logs without debarking. Even British climate seems to be suitable for natural drying of logs. In Central Europe, natural drying is crucial in order to achieve high quality of forest chips for heating. The aims of the DryMe-project are: (1) Remodify and study harvester head which is capable to debark energy wood stems. The aim is to create modified feeding rolls and delimbing knives or extra debarking device, which remove effectively 30-50% of bark during normal harvesting work. The success of debarking will be tested by field experiments and drying trials. Method should work with Silver Birch, Scots Pine and Lodgepole Pine. (2) Test different kinds of bark scarifying patterns and methods according to their capability to evaporate water out from the logs in natural drying. (orig.)

Analytical solutions for prediction of the ignition time of wood particles based on a time and space integral method

International Nuclear Information System (INIS)

Haseli, Y.; Oijen, J.A. van; Goey, L.P.H. de

2012-01-01

Highlights: ► A simple model for prediction of the ignition time of a wood particle is presented. ► The formulation is given for both thermally thin and thermally thick particles. ► Transition from thermally thin to thick regime occurs at a critical particle size. ► The model is validated against a numerical model and various experimental data. - Abstract: The main idea of this paper is to establish a simple approach for prediction of the ignition time of a wood particle assuming that the thermo-physical properties remain constant and ignition takes place at a characteristic ignition temperature. Using a time and space integral method, explicit relationships are derived for computation of the ignition time of particles of three common shapes (slab, cylinder and sphere), which may be characterized as thermally thin or thermally thick. It is shown through a dimensionless analysis that the dimensionless ignition time can be described as a function of non-dimensional ignition temperature, reactor temperature or external incident heat flux, and parameter K which represents the ratio of conduction heat transfer to the external radiation heat transfer. The numerical results reveal that for the dimensionless ignition temperature between 1.25 and 2.25 and for values of K up to 8000 (corresponding to woody materials), the variation of the ignition time of a thermally thin particle with K and the dimensionless ignition temperature is linear, whereas the dependence of the ignition time of a thermally thick particle on the above two parameters obeys a quadratic function. Furthermore, it is shown that the transition from the regime of thermally thin to the regime of thermally thick occurs at K cr (corresponding to a critical size of particle) which is found to be independent of the particle shape. The model is validated by comparing the predicted and the measured ignition time of several wood particles obtained from different sources. Good agreement is achieved which

Creosote movement from treated wood immersed in fresh water

Science.gov (United States)

Sung-Mo Kang; Jeffrey J. Morrell; John Simonsen; Stan Lebow

2005-01-01

Creosote has a long history of successful use as a wood preservative, but polycyclic aromatic hydrocarbons in this preservative have raised environmental concerns, particularly when creosote-treated wood is used in aquatic environments. A number of models have been developed to predict the risk of creosote use in aquatic environments, but one limitation of these models...

Assessment of the wood waste resource and its position in the wood / wood-energy sector - Synthesis

International Nuclear Information System (INIS)

Guinard, Ludovic; Deroubaix, Gerard; Roux, Marie-Lise; Levet, Anne-Laure; Quint, Vincent

2015-04-01

The first objective of this study is to obtain a better knowledge of the 'wood wastes' issue, to propose a photography of the wood waste sector (productions, trades, consumptions), and then to elaborate different prospective scenarios on the use of wood waste volumes while taking into account possible evolutions on the medium or short term of the regulation and market of the wood/wood energy sector. The considered wastes come from industrial production, from the use of wood-based products, and from the end of life of products potentially containing wood. The authors present bibliographical sources and the adopted methodology, briefly describe the 'wood waste' system with its actors, and then report their assessment of wood wastes. They propose a global assessment as well as detailed assessments with respect to waste origins: wood trade and distribution, industries, craft, households and communities, building sector, public and private tertiary sector, packaging. They also address the collection and management of wood wastes by public services, and present the different types of valorisation (panel fabrication, energy, and others). They discuss exports, and then present different scenarios: a trend-based scenario, and two prospective scenarios with a priority to energetic valorisation or to material valorisation of wood wastes. These scenarios are compared

Effects of Heat-Treated Wood Particles on the Physico-Mechanical Properties and Extended Creep Behavior of Wood/Recycled-HDPE Composites Using the Time–Temperature Superposition Principle

Directory of Open Access Journals (Sweden)

Teng-Chun Yang

2017-03-01

Full Text Available This study investigated the effectiveness of heat-treated wood particles for improving the physico-mechanical properties and creep performance of wood/recycled-HDPE composites. The results reveal that the composites with heat-treated wood particles had significantly decreased moisture content, water absorption, and thickness swelling, while no improvements of the flexural properties or the wood screw holding strength were observed, except for the internal bond strength. Additionally, creep tests were conducted at a series of elevated temperatures using the time–temperature superposition principle (TTSP, and the TTSP-predicted creep compliance curves fit well with the experimental data. The creep resistance values of composites with heat-treated wood particles were greater than those having untreated wood particles due to the hydrophobic character of the treated wood particles and improved interfacial compatibility between the wood particles and polymer matrix. At a reference temperature of 20 °C, the improvement of creep resistance (ICR of composites with heat-treated wood particles reached approximately 30% over a 30-year period, and it increased significantly with increasing reference temperature.

Effects of Heat-Treated Wood Particles on the Physico-Mechanical Properties and Extended Creep Behavior of Wood/Recycled-HDPE Composites Using the Time–Temperature Superposition Principle

Science.gov (United States)

Yang, Teng-Chun; Chien, Yi-Chi; Wu, Tung-Lin; Hung, Ke-Chang; Wu, Jyh-Horng

2017-01-01

This study investigated the effectiveness of heat-treated wood particles for improving the physico-mechanical properties and creep performance of wood/recycled-HDPE composites. The results reveal that the composites with heat-treated wood particles had significantly decreased moisture content, water absorption, and thickness swelling, while no improvements of the flexural properties or the wood screw holding strength were observed, except for the internal bond strength. Additionally, creep tests were conducted at a series of elevated temperatures using the time–temperature superposition principle (TTSP), and the TTSP-predicted creep compliance curves fit well with the experimental data. The creep resistance values of composites with heat-treated wood particles were greater than those having untreated wood particles due to the hydrophobic character of the treated wood particles and improved interfacial compatibility between the wood particles and polymer matrix. At a reference temperature of 20 °C, the improvement of creep resistance (ICR) of composites with heat-treated wood particles reached approximately 30% over a 30-year period, and it increased significantly with increasing reference temperature. PMID:28772726

Natural drying treatments during seasonal storage of wood for bioenergy in different European locations

International Nuclear Information System (INIS)

Roeser, Dominik; Mola-Yudego, Blas; Sikanen, Lauri; Prinz, Robert; Gritten, David; Emer, Beatrice; Vaeaetaeinen, Kari; Erkkilae, Ari

2011-01-01

Research into the methods of producing high quality wood chips for a rapidly growing energy sector is becoming increasingly important. For example, small wood chip heating plants require high quality wood chips to ensure efficient operation, thereby minimizing maintenance costs. Moisture content is considered to be an important quality parameter regarding wood based fuels. The objective of this study is to investigate methods to promote the natural drying of wood for bioenergy purposes. The effects on the drying process through covering the wood piles and partial debarking of stems were tested in order to identify methods to reduce the moisture content of the woody material in the storage. Drying trials were established in Finland, Italy and Scotland, utilizing tree species typically used for energy purposes in each area. The results show that natural drying is a viable and effective method to enhance the energy efficiency of wood based fuel products in all the regions studied. Furthermore, by adapting current harvesting methods and storage procedures even better results can be achieved. In addition, the results also indicate that broadleaved trees dry more effectively, if some partial debarking is carried out and that covering of piles is of utmost importance in Scotland and Finland. -- Highlights: → Natural drying is an effective method to enhance efficiency in the wood-fuel chains → Broadleaved trees dry more effectively when partial debarking is done → In Scotland and Finland a method for covering of piles is of utmost importance.

Chapter 6: Wood energy and competing wood product markers

Science.gov (United States)

Kenneth E. Skog; Robert C. Abt; Karen Abt

2014-01-01

Understanding the effect of expanding wood energy markets is important to all wood-dependent industries and to policymakers debating the implementation of public programs to support the expansion of wood energy generation. A key factor in determining the feasibility of wood energy projects (e.g. wood boiler or pellet plant) is the long-term (i.e. 20-30year) supply...

How to use hand-held computers to evaluate wood drying.

Science.gov (United States)

Howard N. Rosen; Darrell S. Martin

1985-01-01

Techniques have been developed to evaluate end generate wood drying curves with hand-held computers (3-5K memory). Predictions of time to dry to a specific moisture content, drying rates, and other characteristics of wood drying curves can be made. The paper describes the development of programs and illustrates their use.

Can wood quality justify local preferences for firewood in an area of caatinga (dryland) vegetation?

Energy Technology Data Exchange (ETDEWEB)

Ramos, Marcelo Alves; Medeiros, Patricia Muniz de; Almeida, Alyson Luiz Santos de; Albuquerque, Ulysses Paulino de [Laboratorio de Etnobotanica Aplicada, Departamento de Biologia, Area de Botanica, Universidade Federal Rural de Pernambuco, Av. Dom Manoel de Medeiros s/n, Dois Irmaos, CEP: 52171-900, Recife, Pernambuco (Brazil); Feliciano, Ana Licia Patriota [Departamento de Ciencia Florestal, Area de Silvicultura, Universidade Federal Rural de Pernambuco, Av. Dom Manoel de Medeiros s/n, Dois Irmaos, CEP: 52171-900, Recife, Pernambuco (Brazil)

2008-06-15

Studies have been undertaken in many parts of the world to evaluate the qualities of fuelwood, but rarely is this information associated with an examination of the preferences of the local populations. As such, the present study sought to address the question of whether local preferences for fuelwoods can be explained by the physical characteristics of the wood itself. To that end, the residents of 102 domiciles in a rural community in NE Brazil were interviewed and a list was compiled of all the plants used and preferred for domestic use. These woods were subsequently analyzed to determine their density, water content, and Fuel Value Index (FVI). Although a total of 67 species were identified by the residents, only 14 were described as being preferred - due to their great number of desirable attributes for cooking. The density, humidity, and FVI of 38 species used and/or preferred were determined. A significant relationship (p<0.05) was noted between plants with the highest FVIs and the most preferred fuelwood plants in the region, indicating that local preference could be explained by the physical properties that were examined. (author)

THE DIFFERENCE OF MACHINING PROPERTIES OF TIMO (Timonius sericeus (Desf K. Schum. And KABESAK WOOD (Acacia leucophloea (Roxb. Willd. FROM EAST NUSA TENGGARA

Directory of Open Access Journals (Sweden)

Heny Rianawati

2015-09-01

Full Text Available Machining properties is one of the parameters to determine the quality of the wood. Tests on machining properties of wood are important to know the easiness level of workmanship as raw materials of furniture industry, construction wood and other wood products. This research was aimed at determining the difference of machining properties between timo wood (Timonius sericeus (Desf K. Schum. and kabesak wood (Acacia leucophloea (Roxb. Willd. from the village of Reknamo, Kupang district, East Nusa Tenggara. Testing procedures were based on ASTM D1666 including: planning, shaping, sanding, drilling and turning. The observation of qualities of the machining were done visually by calculating the percentage of defects that arise on the surface of the samples after the machining process, then the qualities were classified into five quality classes. The results showed that the machining properties of timo wood and kabesak wood were very good and belonging to the quality of class I. The significant difference between the machining properties of both the timbers is in the sanding properties, where the average free defect of sanding timo wood is 85% while kabesak wood is 84.5%. Both timo and kabesak wood are suitable as raw material, for the variety of furniture and molding products.

The Effect of Wood Alignment on Wood Grinding – Part 2: Fines Character and Microscopic Observations

Directory of Open Access Journals (Sweden)

Sabine Heinemann

2016-01-01

Full Text Available During industrial wood grinding, logs are pressed against a rotating stone, with the logs and fibre axes parallel to the axis of the stone. For this study, wood blocks were fed into a laboratory grinder with various alignments in relation to the surface of the grinding stone. The effects of the alignment on the properties of the pulp, the amount, and the quality of the fines were measured, and a grinding mechanism is proposed. In this paper, the obtained results showed that the pulp quality was highly sensitive to the angle between the stone surface and the log, and different for fatigue-based and force-based grinding. The tests were observed using microscopic techniques and discussed in terms of fines amount and fines quality. In gentle refining, the fibre structure is loosened by fatigue before it is bent on the surface, pressure pulses produce fibrillar material, and fibres develop good bonding ability. In forced grinding, the process is “violent” and the fibre wears and is crushed immediately on the surface into small particles with low bonding ability.

Wood frame systems for wood homes

Directory of Open Access Journals (Sweden)

Julio Cesar Molina

2010-12-01

Full Text Available The use of constructive systems that combine strength, speed, with competitive differential techniques and mainly, compromising with the environment, is becoming more popular in Brazil. The constructive system in wood frame for houses of up to five stories is very interesting, because it is a light system, structured in reforested treated wood which allows the combination of several materials, besides allowing speed in the construction and total control of the expenses already in the project phase for being industrialized. The structural behavior of the wood frame is superior to the structural masonry in strength, thermal and acoustic comfort. However, in Brazil, the wood frame is still little known and used, due to lack of technical knowledge about the system, prejudice associated the bad use of the wood as construction material, or still, in some cases, lack of normalization. The aim of this manuscript consists of presenting the main technical characteristics and advantages of the constructive system in wood frame homes, approaching the main stages of the constructive process through examples, showing the materials used in the construction, in addition the main international normative recommendations of the project. Thus, this manuscript also hopes to contribute to the popularization of the wood frame system in Brazil, since it is a competitive, fast and ecologically correct system. Moreover, nowadays, an enormous effort of the technical, commercial and industrial section has been accomplished for the development of this system in the country.

Characteristics and utilization of non-wood pulp and paper; Himokuzai pulp / kami no tokucho to sono riyo

Energy Technology Data Exchange (ETDEWEB)

Hara, H. [Mishima Paper Co. Ltd., Shizuoka (Japan)

1998-09-01

The reasons, difficulty in the usage, and the methods of use of non-wood papers are discussed. Non-wood papers sold in Japan are arranged basing on published data. The type of non-wood paper classified as special printing paper makes up the majority, and there are a variety of other products such as printing board, coated paper, thin paper, wrapping paper, functional paper, and watercolor paper. Kenaf and cotton are used in large quantities as non-wood plants for paper production, and use of bagasse and bamboo is increasing. Non-wood paper are used in consideration of environmental and resources problems and for utilizing the special features of non-wood fiber, and the characteristics of non-wood pulp and the effect of non-wood paper are discussed in this report. It is expected that papers utilizing the characteristics of non-wood paper will be developed. Non-wood papers are substitutions for various papers produced from wood pulp, and the fundamental point is the method of improving the original quality and paper quality by combining with non-wood pulp. 11 refs., 4 figs., 3 tabs.

Harvesting options of small-diameter wood from early thinnings

Energy Technology Data Exchange (ETDEWEB)

Kaerhae, K.; Petty, A. (Metsaeteho Oy, Helsinki (Finland)), e-mail: kalle.karha@metsateho.fi; Mutikainen, A. (TTS Research, Rajamaeki (Finland)), e-mail: arto.mutikainen@tts.fi

2010-07-01

The integrated harvesting of industrial roundwood and energy wood by the so-called 'two-pile cutting method' has increased steadily in young forests in Finland during the last three years. The studies carried out by Metsaeteho Oy and TTS Research (i) determined the time consumption and productivity in cutting work when using the integrated cutting of first-thinning wood, (ii) clarified the development of the total removal in integrated harvesting operation, and (iii) investigated the quality of pulpwood poles when using integrated cutting with multi-tree handling. The studies indicated that the total removal in integrated wood harvesting increase significantly compared to that of conventional, separate roundwood harvesting. When the total removal from the harvesting site increased considerable, there was a significant increase in the productivity of cutting work in integrated wood harvesting compared to the situation in separate pulpwood harvesting. In addition, the delimbing quality and bucking accuracy of the pulpwood poles obtained in multi-tree processing were comparable to those produced in single-tree handling. There were no problems with measuring the work output by a weight scale attached to the crane of the forwarder. As the studies indicated very promising results with integrated wood cutting, integrated harvesting is likely to continue to increase in both first and later thinnings in Finland. (orig.)

Community-weighted mean of leaf traits and divergence of wood traits predict aboveground biomass in secondary subtropical forests.

Science.gov (United States)

Ali, Arshad; Yan, En-Rong; Chang, Scott X; Cheng, Jun-Yang; Liu, Xiang-Yu

2017-01-01

Subtropical forests are globally important in providing ecological goods and services, but it is not clear whether functional diversity and composition can predict aboveground biomass in such forests. We hypothesized that high aboveground biomass is associated with high functional divergence (FDvar, i.e., niche complementarity) and community-weighted mean (CWM, i.e., mass ratio; communities dominated by a single plant strategy) of trait values. Structural equation modeling was employed to determine the direct and indirect effects of stand age and the residual effects of CWM and FDvar on aboveground biomass across 31 plots in secondary forests in subtropical China. The CWM model accounted for 78, 20, 6 and 2% of the variation in aboveground biomass, nitrogen concentration in young leaf, plant height and specific leaf area of young leaf, respectively. The FDvar model explained 74, 13, 7 and 0% of the variation in aboveground biomass, plant height, twig wood density and nitrogen concentration in young leaf, respectively. The variation in aboveground biomass, CWM of leaf nitrogen concentration and specific leaf area, and FDvar of plant height, twig wood density and nitrogen concentration in young leaf explained by the joint model was 86, 20, 13, 7, 2 and 0%, respectively. Stand age had a strong positive direct effect but low indirect positive effects on aboveground biomass. Aboveground biomass was negatively related to CWM of nitrogen concentration in young leaf, but positively related to CWM of specific leaf area of young leaf and plant height, and FDvar of plant height, twig wood density and nitrogen concentration in young leaf. Leaf and wood economics spectra are decoupled in regulating the functionality of forests, communities with diverse species but high nitrogen conservative and light acquisitive strategies result in high aboveground biomass, and hence, supporting both the mass ratio and niche complementarity hypotheses in secondary subtropical forests

Wood density variation and tree ring distinctness in Gmelina arborea trees by x-ray densitometry

Directory of Open Access Journals (Sweden)

Roger Moya

2009-03-01

Full Text Available Due to its relationship with other properties, wood density is the main wood quality parameter. Modern, accuratemethods such as X-ray densitometry - are applied to determine the spatial distribution of density in wood sections and to evaluatewood quality. The objectives of this study were to determinate the influence of growing conditions on wood density variation andtree ring demarcation of gmelina trees from fast growing plantations in Costa Rica. The wood density was determined by X-raydensitometry method. Wood samples were cut from gmelina trees and were exposed to low X-rays. The radiographic films weredeveloped and scanned using a 256 gray scale with 1000 dpi resolution and the wood density was determined by CRAD and CERDsoftware. The results showed tree-ring boundaries were distinctly delimited in trees growing in site with rainfall lower than 2510 mm/year. It was demonstrated that tree age, climatic conditions and management of plantation affects wood density and its variability. Thespecific effect of variables on wood density was quantified by for multiple regression method. It was determined that tree yearexplained 25.8% of the total variation of density and 19.9% were caused by climatic condition where the tree growing. Wood densitywas less affected by the intensity of forest management with 5.9% of total variation.

The suitability of selected wood species in the production of turned ...

African Journals Online (AJOL)

The study investigated the suitability of selected wood species in the production of turned glue-laminated products. Five different wood species of high quality grades which were sourced from Bodija market Ibadan, south western Nigeria were thoroughly examined where the moisture content, density and shrinkage ...

Wood

DEFF Research Database (Denmark)

Unterrainer, Walter

2014-01-01

come from? How is it harvested? How is it manufactured and treated ? How are the buildings detailed and protected against weather during construction to keep them dry and make them long-life ? In a period of climate change, forests are the last lungs of the planet to sequestrate CO2. Their global size......Wood – a sustainable building material ? For thousands of years and all over the planet, wood has been used as a building material and exciting architecture has been created in wood. The fantastic structural, physical and aesthetic properties of the material as well as the fact that wood...

Wood burning

Energy Technology Data Exchange (ETDEWEB)

Winkelmann, H

1955-01-01

Discussed are the use of wood as a fuel, the technique of wood combustion and the operation of wood-burning stoves for cooking and heating. In addition, there is a section which reviews the use of wood stoves in various countries and lists manufacturers of stoves, central heating furnaces and in some cases sawdust burners.

Application of photocuring technique on wood surface and its prospects in Bangladesh

International Nuclear Information System (INIS)

Bhattcacharia, S.K.; Khan, Mubarak A.

2005-01-01

Photocuring technique has unveiled a new horizon in polymer science. Application of photocuring technique on wood surface has enhanced the use of low grade wood. As Bangladesh is an overpopulated country, necessity of good quality wood is increasing day by day. So low grade wood, like Simul or Partex, locally produced particleboard, would come out with great use. As Partex board, produced from Jute sticks and various types of indigenous low grade wood and particle board are abundant in Bangladesh, so photocuring could play a major role to improve the quality of low grade wood and serve the nation. Already, a lot of research works were carried out by the local scientists to improve the wood surface using UV curing method. Different formulations were also developed by the local scientists using various oligomer, monomer and different types of additives. The used oligomers are epoxy, polyester, urethane, etc. and monomers of different functionalities and used additives are acrylic monomer, CaCO 3 , sand, MgSiO 3 , talc, etc. Thin films were prepared on glass plate with different formulations using UV radiation and different characteristics properties (pendulum hardness, abrasion, gloss (60 deg. and 20 deg.), microscratch hardness, weathering effect, adhesion strength, etc.) were studied. Now, a Pilot Plant has already been established with the financial assistance by the government of Bangladesh, worth US$ 3.5 million

Wood energy in Switzerland - State of the art, developments and potential

International Nuclear Information System (INIS)

Rutschmann, C.

2006-01-01

This article reviews the present-day use of wood as a source of energy and the potential it exhibits as part of a future Swiss energy supply system. The history of the use of wood to provide energy is looked at and its changing share of total energy consumption is commented on. In particular, the use of wood energy during the period 1991-2004 is looked at and its promotion by various programmes examined. Apart from wood-fired heating systems, open fires are commented on as are the changes noted over this period in the types of heating systems installed. The potential of wood-energy and custom-tailored solutions are looked at. The important role played by quality assurance for fast market development is stressed. Finally, the role to be played by wood energy in the future is looked at

Competitive outcomes between wood-decaying fungi are altered in burnt wood.

Science.gov (United States)

Edman, Mattias; Eriksson, Anna-Maria

2016-06-01

Fire is an important disturbance agent in boreal forests where it creates a wide variety of charred and other types of heat-modified dead wood substrates, yet how these substrates affect fungal community structure and development within wood is poorly understood. We allowed six species of wood-decaying basidiomycetes to compete in pairs in wood-discs that were experimentally burnt before fungal inoculation. The outcomes of interactions in burnt wood differed from those in unburnt control wood for two species:Antrodia sinuosanever lost on burnt wood and won over its competitor in 67% of the trials compared to 40% losses and 20% wins on unburnt wood. In contrast, Ischnoderma benzoinumwon all interactions on unburnt wood compared to 33% on burnt wood. However, the responses differed depending on the identity of the competing species, suggesting an interaction between competitor and substrate type. The observed shift in competitive balance between fungal species probably results from chemical changes in burnt wood, but the underlying mechanism needs further investigation. Nevertheless, the results indicate that forest fires indirectly structure fungal communities by modifying dead wood, and highlight the importance of fire-affected dead wood substrates in boreal forests. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Gasification of Wood and Non-wood Waste of Timber Production as Perspectives for Development of Bioenergy

Science.gov (United States)

Kislukhina, Irina A.; Rybakova, Olga G.

2018-03-01

The article deals with biomass gasification technology using the gasification plant running on wood chips and pellets, produced from essential oils waste (waste of coniferous boughs). During the study, the authors solved the process task of improving the quality of the product gas derived from non-wood waste of timber production (coniferous boughs) due to the extraction of essential oils and the subsequent thermal processing of spent coniferous boughs at a temperature of 250-300°C degrees without oxygen immediately before pelleting. The paper provides the improved biomass gasification process scheme including the grinding of coniferous boughs, essential oil distillation and thermal treatment of coniferous boughs waste and pelletizing.

World trade in forest products and wood fuel

International Nuclear Information System (INIS)

Hillring, Bengt

2006-01-01

Wood fuel is a strategic resource for future energy supply and is usually utilised locally. Traditional use of wood fuel and other bioenergy has a share of 10-15% energy supply, used mainly for the household sector. The utilisation for industrial purposes is much smaller but is a strategic resource in the effort to fulfil the Kyoto agreement to replace fossil fuels and to mitigate greenhouse gas emissions. Many industrialised countries already use a significant share of biofuels in their energy supply e.g. Nordic countries while others like some other European Union countries are planning to increase their use. Production and use of biofuels need to be carried out sustainable. Official statistics do not report trade in such detail that international trade in different biomass types can be fully identified. However, FAO and European Forestry Institute are important sources. In some countries, there is a growing interest in the international trade, because the trade can provide biofuels at lower prices, larger quantities and better quality than domestic alternatives. The first signs of an international market price for wood fuel are indicated in Europe. For the future both the use and the trade of wood fuel is expected to increase. Analyses for trade in charcoal, wood chips, fuel wood and wood residues made in this report identify 'hot' trade spots in Europe, in south East Asia and in North America

Strength development in concrete with wood ash blended cement and use of soft computing models to predict strength parameters.

Science.gov (United States)

Chowdhury, S; Maniar, A; Suganya, O M

2015-11-01

In this study, Wood Ash (WA) prepared from the uncontrolled burning of the saw dust is evaluated for its suitability as partial cement replacement in conventional concrete. The saw dust has been acquired from a wood polishing unit. The physical, chemical and mineralogical characteristics of WA is presented and analyzed. The strength parameters (compressive strength, split tensile strength and flexural strength) of concrete with blended WA cement are evaluated and studied. Two different water-to-binder ratio (0.4 and 0.45) and five different replacement percentages of WA (5%, 10%, 15%, 18% and 20%) including control specimens for both water-to-cement ratio is considered. Results of compressive strength, split tensile strength and flexural strength showed that the strength properties of concrete mixture decreased marginally with increase in wood ash contents, but strength increased with later age. The XRD test results and chemical analysis of WA showed that it contains amorphous silica and thus can be used as cement replacing material. Through the analysis of results obtained in this study, it was concluded that WA could be blended with cement without adversely affecting the strength properties of concrete. Also using a new statistical theory of the Support Vector Machine (SVM), strength parameters were predicted by developing a suitable model and as a result, the application of soft computing in structural engineering has been successfully presented in this research paper.

Evaluation of usher wood and karkadeh stem for charcoal in Sudan

Energy Technology Data Exchange (ETDEWEB)

Khristova, P. (Khartoum Univ. (Sudan)); Vergnet, L. (CTFT, 94 - Nogent s/Marne (France). Energie Div.)

1993-01-01

Two unusual biomass materials Hibiscus sabdariffa var. sabdariffa (karkadeh) stem and Calotropis procera (usher) wood were investigated in the laboratory as potential raw materials for charcoal making in Sudan. The materials were characterised physically and chemically and despite the low density and high bark-to-wood ratio by volume, good yields and quality of charcoal were predicted. The carbonization trials with a laboratory retort at conditions close to those of field metal kiln gave very good charcoal yields (35% for karkadeh and 38% for usher) with high energy transformation (58% and 62%, respectively). The karkadeh charcoal, except for a somewhat high ash content, was good for domestic uses (79% fixed carbon and 30.3 MJ kg[sup -1] heat value). The usher charcoal was better with respect to fixed carbon (86.5%) and gross heat value (32.4 MJ kg[sup -1]). Both charcoals were of low density (140-160 kg m[sup -3]) and further assessment of their economic suitability should be carried out under field conditions. The carbonization by-products were also collected and characterized by means of gas chromatography. (author)

INFLUENCE OF ANATOMICAL FEATURES AND EXTRACTIVES CONTENT WOOD OF Eucalyptus grandis W. Hill ex Maiden IN QUALITY BONDING

Directory of Open Access Journals (Sweden)

Vanessa Cristina do Sacramento Albino

2012-12-01

Full Text Available http://dx.doi.org/10.5902/198050987561The study aimed to anatomically characterize and to quantify the total extractives in different positions of the log of Eucalyptus grandis W. Hill ex Maiden with 18 years of age and to assess their influence on the shear strength and percentage of wood failure in adhesive bonded joints with thermosetting resorcinol-formaldehyde. Histological slides were prepared for an anatomical study and determined the total extractive content. The preparation of bonded joints was made according to ASTM D 2339-98(2000. It was used the correlation coefficient of Pearson, 1% probability by t test to evaluate the correlation between the anatomical and extractives content with the quality of the glued joints. It was found that there was a correlation between the shear strength with the following characteristics: vessel diameter, wall width, length and width of the fiber, the width of the radius and total extractives content. For the percentage of wood failure, there was a correlation between this with the following characteristics: the frequency of vessels, thickness of the heat of fiber, and high frequency of lightning. Both the radial direction as in the longitudinal direction of the logs there was change in the values found for the measurement of the anatomical elements, the total amount of extractives, the shear test strength and the percentage of wood failure.

Woods with physical, mechanical and acoustic properties similar to those of Caesalpinia echinata have high potential as alternative woods for bow makers

Directory of Open Access Journals (Sweden)

Eduardo Luiz Longui

2014-09-01

Full Text Available For nearly two hundred years, Caesalpinia echinata wood has been the standard for modern bows. However, the threat of extinction and the enforcement of trade bans have required bow makers to seek alternative woods. The hypothesis tested was that woods with physical, mechanical and acoustic properties similar to those of C. echinata would have high potential as alternative woods for bows. Accordingly, were investigated Handroanthus spp., Mezilaurus itauba, Hymenaea spp., Dipteryx spp., Diplotropis spp. and Astronium lecointei. Handroanthus and Diplotropis have the greatest number of similarities with C. echinata, but only Handroanthus spp. showed significant results in actual bow manufacture, suggesting the importance of such key properties as specific gravity, speed of sound propagation and modulus of elasticity. In practice, Handroanthus and Dipteryx produced bows of quality similar to that of C. echinata.

The Effect of Wood Alignment on Wood Grinding – Part 1: Properties of Pulp and Fines Revealed in the Grinding Mechanism

Directory of Open Access Journals (Sweden)

Erkki Tapani Saharinen

2016-03-01

Full Text Available In industrial wood grinding, logs are pressed against a rotating stone, with the logs and fiber axis parallel to the axis of the stone. The objective of this study is to clarify how the wood alignment affects the process and pulp properties. In this research, wood blocks were fed into a laboratory grinder with various alignments in relation to the surface of the grinding stone. The effects of the alignment on the properties of the pulp and the amount and quality of fines were measured. A grinding mechanism was proposed. The results show that the pulp quality is very sensitive to the angle between the stone surface and the log. In gentle refining, the fiber structure is loosened by fatigue before it is bent on the surface; pressure pulses produce fibrillar material, and fibers develop toward having good bonding ability. In forced grinding, the process is “violent”, and the fiber wears and becomes crushed immediately on the surface into small particles with low bonding ability.

Wood density explains architectural differentiation across 145 co-occurring tropical tree species

NARCIS (Netherlands)

Iida, Y.; Poorter, L.; Sterck, F.J.; Kubo, T.; Kassim, A.R.; Potts, M.D.; Kohyama, T.S.

2012-01-01

1. Because of its mechanical properties, wood density may affect the way that trees expand their stem and crown to exploit favourable light conditions in a mechanically stable way. From engineering theory and wood density properties, it is predicted that in terms of biomass investment, low-density

Developments to the Sylvan stand structure model to describe wood quality changes in southern bottomland hardwood forests because of forest management

Science.gov (United States)

Ian R. Scott

2009-01-01

Growth models can produce a wealth of detailed information that is often very difficult to perceive because it is frequently presented either as summary tables, stand view or landscape view visualizations. We have developed new tools for use with the Sylvan model (Larsen 1994) that allow the analysis of wood-quality changes as a consequence of forest management....

Potential wood protection strategies using physiological requirements of wood degrading fungi

NARCIS (Netherlands)

Sailer, M.F.; Etten, B.D. van

2004-01-01

Due to the increasing restrictions in the use of wood preserving biocides a number of potential biocide free wood preserving alternatives are currently assessed. Wood degrading fungi require certain conditions in the wood in order to be able to use wood as a food source. This paper discusses the

Observed relationships between wood density and solution uptake during pressure treatment

Science.gov (United States)

Steve Halverson; Stan Lebow

2011-01-01

A better understanding of the relationship between wood properties and solution uptake during pressure treatment could lead to improvements in treatment quality and more efficient use of preservatives. In this study several years of treatment data representing a range of wood species, charge conditions and preservative formulations were analyzed to evaluate the...

Source apportionment of PM2.5 at multiple Northwest U.S. sites: Assessing regional winter wood smoke impacts from residential wood combustion

Science.gov (United States)

Kotchenruther, Robert A.

2016-10-01

Wood smoke from residential wood combustion is a significant source of elevated PM2.5 in many communities across the Northwest U.S. Accurate representation of residential wood combustion in source-oriented regional scale air quality models is challenging because of multiple uncertainties. As an alternative to source-oriented source apportionment, this work provides, through receptor-oriented source apportionment, an assessment of winter residential wood combustion impacts at multiple Northwest U.S. locations. Source apportionment was performed on chemically speciated PM2.5 from 19 monitoring sites using the Positive Matrix Factorization (PMF) receptor model. Each site was modeled independently, but a common data preparation and modeling protocol was used so that results were as comparable as possible across sites. Model solutions had from 4 to 8 PMF factors, depending on the site. PMF factors at each site were associated with a source classification (e.g., primary wood smoke), a dominant chemical composition (e.g., ammonium nitrate), or were some mixture. 15 different sources or chemical compositions were identified as contributing to PM2.5 across the 19 sites. The 6 most common were; aged wood smoke and secondary organic carbon, motor vehicles, primary wood smoke, ammonium nitrate, ammonium sulfate, and fugitive dust. Wood smoke was identified at every site, with both aged and primary wood smoke identified at most sites. Wood smoke contributions to PM2.5 were averaged for the two winter months of December and January, the months when wood smoke in the Northwest U.S. is mainly from residential wood combustion. The total contribution of residential wood combustion, that from primary plus aged smoke, ranged from 11.4% to 92.7% of average December and January PM2.5 depending on the site, with the highest percent contributions occurring in smaller towns that have fewer expected sources of winter PM2.5. Receptor modeling at multiple sites, such as that conducted in this

Postprocessing for Air Quality Predictions

Science.gov (United States)

Delle Monache, L.

2017-12-01

In recent year, air quality (AQ) forecasting has made significant progress towards better predictions with the goal of protecting the public from harmful pollutants. This progress is the results of improvements in weather and chemical transport models, their coupling, and more accurate emission inventories (e.g., with the development of new algorithms to account in near real-time for fires). Nevertheless, AQ predictions are still affected at times by significant biases which stem from limitations in both weather and chemistry transport models. Those are the result of numerical approximations and the poor representation (and understanding) of important physical and chemical process. Moreover, although the quality of emission inventories has been significantly improved, they are still one of the main sources of uncertainties in AQ predictions. For operational real-time AQ forecasting, a significant portion of these biases can be reduced with the implementation of postprocessing methods. We will review some of the techniques that have been proposed to reduce both systematic and random errors of AQ predictions, and improve the correlation between predictions and observations of ground-level ozone and surface particulate matter less than 2.5 µm in diameter (PM2.5). These methods, which can be applied to both deterministic and probabilistic predictions, include simple bias-correction techniques, corrections inspired by the Kalman filter, regression methods, and the more recently developed analog-based algorithms. These approaches will be compared and contrasted, and strength and weaknesses of each will be discussed.

Important Non-Wood Forest Products in Turkey: An Econometric Analysis

Directory of Open Access Journals (Sweden)

R. Kurt

2016-12-01

Full Text Available Wood resources obtained from forest and non-wood forest products (NWFP have gained great importance recently as their economic values keeps increasing by the day. In this study, forecasting of Turkish Non-Wood Forest Products such as thyme, bay leaves, salvia and pine nut export amounts was carried out using a linear regression analysis method for the next fifteen years based on the data for the years between 1990 and 2009. Moreover, estimated import values and actual import values from the last years were compered and analyzed. Finally, predictions on future trends were made.

[Environmental and health impacts of wood combustion to produce heat and power].

Science.gov (United States)

Valerio, Federico

2012-01-01

Toxic chemicals such as benzene, polycyclic aromatic hydrocarbons, dioxins, and ultra fine particles were found in the smoke produced by wood combustion. Emission factors confirm that, to produce the same energy amount, many more pollutants are emitted by wood than by natural gas. Biomass burning produces a relevant deterioration of air quality inside and outside houses, notably due to emissions of fine and ultra fine dust (PM10, PM2.5) according to reviewed studies. Important improvements in emission quality are obtained with the use of more efficient household heating systems, both in developed and in developing countries. Numerous studies have assessed the possible health effects produced by wood smoke, providing sufficient evidence that the indoor exposure to wood smoke, even in developed countries, can have adverse effects on human health. In 2010 IARC classified wood smoke as a possible human carcinogen. In Europe, electricity generation from biomass combustion is increasing (12% each year) thanks to incentives provided to reduce greenhouse gas emissions and use of fossil fuels.Today adequate studies to assess the environmental and health effects of emissions from power plants fuelled by solid biomasses are still needed.

Functional relationships between wood structure and vulnerability to xylem cavitation in races of Eucalyptus globulus differing in wood density.

Science.gov (United States)

Barotto, Antonio José; Monteoliva, Silvia; Gyenge, Javier; Martinez-Meier, Alejandro; Fernandez, María Elena

2018-02-01

Wood density can be considered as a measure of the internal wood structure, and it is usually used as a proxy measure of other mechanical and functional traits. Eucalyptus is one of the most important commercial forestry genera worldwide, but the relationship between wood density and vulnerability to cavitation in this genus has been little studied. The analysis is hampered by, among other things, its anatomical complexity, so it becomes necessary to address more complex techniques and analyses to elucidate the way in which the different anatomical elements are functionally integrated. In this study, vulnerability to cavitation in two races of Eucalyptus globulus Labill. with different wood density was evaluated through Path analysis, a multivariate method that allows evaluation of descriptive models of causal relationship between variables. A model relating anatomical variables with wood properties and functional parameters was proposed and tested. We found significant differences in wood basic density and vulnerability to cavitation between races. The main exogenous variables predicting vulnerability to cavitation were vessel hydraulic diameter and fibre wall fraction. Fibre wall fraction showed a direct impact on wood basic density and the slope of vulnerability curve, and an indirect and negative effect over the pressure imposing 50% of conductivity loss (P50) through them. Hydraulic diameter showed a direct negative effect on P50, but an indirect and positive influence over this variable through wood density on one hand, and through maximum hydraulic conductivity (ks max) and slope on the other. Our results highlight the complexity of the relationship between xylem efficiency and safety in species with solitary vessels such as Eucalyptus spp., with no evident compromise at the intraspecific level. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Accumulation of Elements in Salix and Other Species Used in Vegetation Filters with Focus on Wood Fuel Quality

Energy Technology Data Exchange (ETDEWEB)

Adler, Anneli

2007-07-01

Woody or herbaceous perennials used as vegetation filters for treatment of different types of wastes can be suitable for production of solid biofuels when their above ground harvestable biomass yield is sufficiently high and when biomass contains appropriate concentrations of minerals with regard to fuel combustion processes. The concentrations of nitrogen (N), potassium (K) and heavy metals (especially Zn and Cd) in fuel should be low and calcium (Ca) concentrations high to avoid technical problems and environmentally harmful emissions during combustion. Since soil supplementation with essential elements improves biomass yield, a conflict might arise between yield and quality aims. There are various possibilities to influence fuel quality during the growing phase of the life cycle of perennial biomass crops. This study assessed the suitability of two deciduous woody perennials (Salix and Populus) and two summer green herbaceous perennials (Phragmites and Urtica) for phytoremediation in terms of growth and nutrient allocation patterns. Salix and Populus proved suitable as vegetation filters when nutrients were available to plants in near-optimal proportions, but when unbalanced nutrient solutions (wastewater) were applied, stem biomass fraction was strongly reduced. Phragmites was more tolerant to wastewater treatment in terms of plant biomass production and nutrient allocation patterns, so if the N:P ratio of the wastewater is suboptimal, a vegetation filter using Phragmites could be considered. In further studies, a method was developed to determine the proportions of nutrient-rich bark in coppiced Salix, while heavy metal phytoextraction capacity was assessed in two Salix vegetation filters. The relevance of proportion of bark on wood fuel quality and element removal from vegetation filters was also investigated. The concentrations of the elements studied in harvestable Salix shoot biomass were higher, meaning lower wood fuel quality, in plantations where

Ambient air pollution associated to domestic wood burning heating systems

International Nuclear Information System (INIS)

Friboulet, I.; Durif, M.; Malherbe, L.

2009-01-01

Main publications are considering effects of wood burning appliances on indoor air quality, which is a major issue in some countries. But impacts on ambient air, close environment and human exposure are rather poorly characterised so far. Besides, woods burning for domestic purpose may develop in the next years while promoting bio fuels. The aim of the ongoing study is to assess in which conditions associated air pollution and population exposure could be significant, this poster shows preliminary results of the impact of a village of 98 houses equipped with a wood burning heating system. (N.C.)

CHARACTERIZATION OF EMISSIONS OF THERMALLY MODIFIED WOOD AND THEIR REDUCTION BY CHEMICAL TREATMENT

Directory of Open Access Journals (Sweden)

Jana Peters

2008-05-01

Full Text Available Thermal treatment is a suitable method for improving the quality of wood types like spruce, beech or poplar, and thus to open up new fields of application that used to be limited to tropical woods or woods treated with timber preservatives. These thermally treated woods are characterized by a typical odor caused by degradation products of miscellaneous wood components. The characterization and removal of those odorous substances were investigated using chromatographic and spectroscopic methods. Headspace gas chromatography (GC in combination with solid-phase microextraction (SPME was used for a qualitative analysis of volatile wood emissions, and the detectable volatiles were compared before and after solvent extraction. Wood solvent extractives were investigated by means of gas chromatography/mass spectrometry and then evaluated in terms of changes in composition caused by the thermal treatment process.

Can forest dieback and tree death be predicted by prior changes in wood anatomy?

Science.gov (United States)

Colangelo, Michele; Julio Camarero, Jesus; De Micco, Veronica; Borghetti, Marco; Gentilesca, Tiziana; Sanchez-Salguero, Raul; Ripullone, Francesco

2017-04-01

Climate warming is expected to amplify drought stress resulting in more intense and widespread dieback episodes and increasing mortality rates. Studies on quantitative wood anatomy and dendrochronology have demonstrated their potential to supply useful information on the causes of tree decline, although this approach is basically observational and retrospective. Moreover, the long-term reconstruction of wood anatomical features, strictly linked to the evolution of xylem anatomy plasticity through time, allow investigating hydraulic adjustments of trees. In this study, we analyzed wood-anatomical variables in two Italian oak forests where recent episodes of dieback and mortality have been reported. We analyzed in coexisting now-dead and living trees the following wood-anatomical variables: annual tree-ring area, earlywood (EW) and latewood (LW) areas, absolute and relative (%) areas occupied by vessels in the EW and LW, EW and LW vessel areas, EW and LW vessel density and vessel diameter classification. We also calculated the hydraulic diameter (Dh) for all vessels measured within each ring by weighting individual conduit diameters to correspond to the average Hagen-Poiseuille lumen theoretical hydraulic conductivity for a vessel size. Wood-anatomical analyses showed that declining and dead trees were more sensitive to drought stress compared to non declining trees, indicating different susceptibility to water shortage between trees. Dead trees did not form earlywood vessels with smaller lumen diameter than surviving trees but tended to form wider latewood vessels with a higher percentage of vessel area. We discuss the results and implications focusing on those proved more sensitive to the phenomena of decline and mortality.

Wood Identification of 18th Century Furniture. Interpreting Wood Naming Inventoires

Directory of Open Access Journals (Sweden)

Rocio Astrid BERNAL

2011-09-01

Full Text Available The 18th century Portuguese church furniture represents an extraordinary richness recognised worldwide, which demands safeguarding and valorisation. The identification of the wood of furniture artworks is the most important component for its comprehension and preservation. In this work wood anatomical characters of an 18th century Portuguese decorative furniture set from the Colegiada de São Martinho de Cedofeita, in Porto, were analysed to identify the woods used for manufacturing and to clarify their common names. Furthermore, the objectives were to recognise some of the criteria for choice of wood as well as the source of each wood. The woods identified from 16 fragments belong to Apuleia sp., Acacia sp., Neolamarckia sp. and Castanea sativa. Apuleia sp. and Acacia sp. woods most likely arrived from Brazil, while the Neolamarckia sp. woods likely arrived from India and the C. sativa woods from Portugal. The results are in accordance with the known Portuguese colonial sea routes of the 15th -18th centuries. Interestingly the terms found in the inventories can refer to finishing methods instead to the name of the woods, as for instance “oil wood” can refer to “oiled wood” or “linseed oiled wood”. The species choice may be related to the mechanical properties of the wood as well as the original tree size. Two large planks of Acacia sp. were used for the top of the “Portuguese arcaz”, and Apuleia sp. was found on main structural elements of this set of furniture, suggesting that wood colour was also important. Woods from Neolamarckia sp. and C. sativa, were also identified, being Castanea wood present only in the most recent pieces of the furniture set.

13C-isotopic fingerprint of Pinus pinaster Ait. and Pinus sylvestris L. wood related to the quality of standing tree mass in forests from NW Spain.

Science.gov (United States)

Fernandez, Irene; González-Prieto, Serafin J; Cabaneiro, Ana

2005-01-01

Pine forest plantations of Pinus pinaster Ait. and P. sylvestris L. located in Galicia, NW Spain, were selected to study the 13C/12C-isotopic fingerprint in wood core samples in order to find possible relationships between the delta(13)C at natural abundance levels and the quality of the standing tree mass. For each pine species, 24 forests growing on acidic soils were studied: half developed over granite and half over schists. Two dominant trees from each plot, corresponding to all possible combinations of forest stands with high or low site index and with adults or young trees, were drilled at the basal part of trunks using a Pressler drill to obtain tree ring samples. The C-isotopic compositions of the litter and the soil organic matter from different soil depths were also determined and statistically significant correlations between these values and the 13C content of the wood were observed. Despite internal variations due to the influence of site index, tree age and parent material, the isotopic fingerprint of P. pinaster wood (mean value delta13C=-26.2+/-0.8 per thousand) significantly differed (Ppinaster stands (r=-0.667, Ppinaster growing over schists (r=-0.833, Ppinaster trees is higher when plots over granite or schists are separately considered. A similar fact occurs for adult P. sylvestris trees from schists stands, high quality specimens being 13C-depleted compared with low quality ones. On the other hand, 13C natural abundance of wood from P. sylvestris trees seems to be also strongly influenced by the underlying parent material, young trees from granite stands having a statistically higher 13C-isotopic composition (P<0.05) than young trees from schists stands. Copyright (c) 2005 John Wiley & Sons, Ltd.

Wood-related occupations, wood dust exposure, and sinonasal cancer.

Science.gov (United States)

Hayes, R B; Gerin, M; Raatgever, J W; de Bruyn, A

1986-10-01

A case-control study was conducted to examine the relations between type of woodworking and the extent of wood dust exposure to the risks for specific histologic types of sinonasal cancer. In cooperation with the major treatment centers in the Netherlands, 116 male patients newly diagnosed between 1978 and 1981 with primary malignancies of epithelial origin of this site were identified for study. Living controls were selected from the municipal registries, and deceased controls were selected from the national death registry. Interviews were completed for 91 (78%) cases and 195 (75%) controls. Job histories were coded by industry and occupation. An index of exposure was developed to classify the extent of occupational exposure to wood dust. When necessary, adjustment was made for age and usual cigarette use. The risk for nasal adenocarcinoma was elevated by industry for the wood and paper industry (odds ratio (OR) = 11.9) and by occupation for those employed in furniture and cabinet making (OR = 139.8), in factory joinery and carpentry work (OR = 16.3), and in association with high-level wood dust exposure (OR = 26.3). Other types of nasal cancer were not found to be associated with wood-related industries or occupations. A moderate excess in risk for squamous cell cancer (OR = 2.5) was associated with low-level wood dust exposure; however, no dose-response relation was evident. The association between wood dust and adenocarcinoma was strongest for those employed in wood dust-related occupations between 1930 and 1941. The risk of adenocarcinoma did not appear to decrease for at least 15 years after termination of exposure to wood dust. No cases of nasal adenocarcinoma were observed in men whose first exposure to wood dust occurred after 1941.

Near Infrared Spectroscopy Calibration for Wood Chemistry: Which Chemometric Technique Is Best for Prediction and Interpretation?

Directory of Open Access Journals (Sweden)

Brian K. Via

2014-07-01

Full Text Available This paper addresses the precision in factor loadings during partial least squares (PLS and principal components regression (PCR of wood chemistry content from near infrared reflectance (NIR spectra. The precision of the loadings is considered important because these estimates are often utilized to interpret chemometric models or selection of meaningful wavenumbers. Standard laboratory chemistry methods were employed on a mixed genus/species hardwood sample set. PLS and PCR, before and after 1st derivative pretreatment, was utilized for model building and loadings investigation. As demonstrated by others, PLS was found to provide better predictive diagnostics. However, PCR exhibited a more precise estimate of loading peaks which makes PCR better for interpretation. Application of the 1st derivative appeared to assist in improving both PCR and PLS loading precision, but due to the small sample size, the two chemometric methods could not be compared statistically. This work is important because to date most research works have committed to PLS because it yields better predictive performance. But this research suggests there is a tradeoff between better prediction and model interpretation. Future work is needed to compare PLS and PCR for a suite of spectral pretreatment techniques.

Near infrared spectroscopy calibration for wood chemistry: which chemometric technique is best for prediction and interpretation?

Science.gov (United States)

Via, Brian K; Zhou, Chengfeng; Acquah, Gifty; Jiang, Wei; Eckhardt, Lori

2014-07-25

This paper addresses the precision in factor loadings during partial least squares (PLS) and principal components regression (PCR) of wood chemistry content from near infrared reflectance (NIR) spectra. The precision of the loadings is considered important because these estimates are often utilized to interpret chemometric models or selection of meaningful wavenumbers. Standard laboratory chemistry methods were employed on a mixed genus/species hardwood sample set. PLS and PCR, before and after 1st derivative pretreatment, was utilized for model building and loadings investigation. As demonstrated by others, PLS was found to provide better predictive diagnostics. However, PCR exhibited a more precise estimate of loading peaks which makes PCR better for interpretation. Application of the 1st derivative appeared to assist in improving both PCR and PLS loading precision, but due to the small sample size, the two chemometric methods could not be compared statistically. This work is important because to date most research works have committed to PLS because it yields better predictive performance. But this research suggests there is a tradeoff between better prediction and model interpretation. Future work is needed to compare PLS and PCR for a suite of spectral pretreatment techniques.

Effect of cement/wood ratios and wood storage conditions on hydration temperature, hydration time, and compressive strength of wood-cement mixtures

Science.gov (United States)

Andy W.C. Lee; Zhongli Hong; Douglas R. Phillips; Chung-Yun Hse

1987-01-01

This study investigated the effect of cement/wood ratios and wood storage conditions on hydration temperature, hydration time, and compressive strength of wood-cement mixtures made from six wood species: southern pine, white oak, southern red oak, yellow-poplar, sweetgum, and hickory. Cement/wood ratios varied from 13/1 to 4/1. Wood storage conditions consisted of air-...

Strength development in concrete with wood ash blended cement and use of soft computing models to predict strength parameters

Directory of Open Access Journals (Sweden)

S. Chowdhury

2015-11-01

Full Text Available In this study, Wood Ash (WA prepared from the uncontrolled burning of the saw dust is evaluated for its suitability as partial cement replacement in conventional concrete. The saw dust has been acquired from a wood polishing unit. The physical, chemical and mineralogical characteristics of WA is presented and analyzed. The strength parameters (compressive strength, split tensile strength and flexural strength of concrete with blended WA cement are evaluated and studied. Two different water-to-binder ratio (0.4 and 0.45 and five different replacement percentages of WA (5%, 10%, 15%, 18% and 20% including control specimens for both water-to-cement ratio is considered. Results of compressive strength, split tensile strength and flexural strength showed that the strength properties of concrete mixture decreased marginally with increase in wood ash contents, but strength increased with later age. The XRD test results and chemical analysis of WA showed that it contains amorphous silica and thus can be used as cement replacing material. Through the analysis of results obtained in this study, it was concluded that WA could be blended with cement without adversely affecting the strength properties of concrete. Also using a new statistical theory of the Support Vector Machine (SVM, strength parameters were predicted by developing a suitable model and as a result, the application of soft computing in structural engineering has been successfully presented in this research paper.

Rapid Assessment Of The Fundamental Property Variation Of Wood

Science.gov (United States)

Chi-Leung So; Leslie H. Groom; Timothy G. Rials; Rebecca Snell; Stephen S. Kelley; Robert Meglen

2002-01-01

Abstract - Genetic variation, site conditions, silvicultural treatments, seasonal effects, and their complex interaction are all vitally-important factors accounting for the variability and quality of the raw material produced - wood. Quality can be measured in several ways that generally influence the end use. The most desirable measure is the...

Properties of Hungarian oak(quercus conferta Kit. wood from the Hilandar Monastery forest

Directory of Open Access Journals (Sweden)

Popović Zdravko

2007-01-01

Full Text Available This paper presents the study results of the basic physical and strength properties of Hungarian oak (Quercus conferta Kit. wood from the Kakovo Monastery forests of Hilandar Monastery in Greece. Wood properties were analyzed in detail, as an indispensable proof of wood quality and its use for joinery, interiors and wooden floors. The basic physical properties of wood (moisture content at the time of tree felling, density and volume porosity and the basic strength properties (compressive strength, bending strength and module of elasticity were researched. The results are presented in Tables and in Diagrams with statistical parameters and compared to the literature data. The correlation of the study properties of wood was also analyzed.

Identifying Success Factors in the Wood Pallet Supply Chain

OpenAIRE

Sanchez, Leslie Scarlett

2011-01-01

Pallets are a critical component of logistics infrastructure. Approximately 1.9 billion pallets are used each year in the United States for transportation of goods, from raw materials to finished products. Solid wood pallets represent 90% to 95% of the pallet market. To run their operations, wood pallet companies deal with suppliers, customers, and other supply chain components. Each of the steps is important to deliver the right products, with the required quality, and in a timely fashion. H...

Predicting the Overall Spatial Quality of Automotive Audio Systems

Science.gov (United States)

Koya, Daisuke

The spatial quality of automotive audio systems is often compromised due to their unideal listening environments. Automotive audio systems need to be developed quickly due to industry demands. A suitable perceptual model could evaluate the spatial quality of automotive audio systems with similar reliability to formal listening tests but take less time. Such a model is developed in this research project by adapting an existing model of spatial quality for automotive audio use. The requirements for the adaptation were investigated in a literature review. A perceptual model called QESTRAL was reviewed, which predicts the overall spatial quality of domestic multichannel audio systems. It was determined that automotive audio systems are likely to be impaired in terms of the spatial attributes that were not considered in developing the QESTRAL model, but metrics are available that might predict these attributes. To establish whether the QESTRAL model in its current form can accurately predict the overall spatial quality of automotive audio systems, MUSHRA listening tests using headphone auralisation with head tracking were conducted to collect results to be compared against predictions by the model. Based on guideline criteria, the model in its current form could not accurately predict the overall spatial quality of automotive audio systems. To improve prediction performance, the QESTRAL model was recalibrated and modified using existing metrics of the model, those that were proposed from the literature review, and newly developed metrics. The most important metrics for predicting the overall spatial quality of automotive audio systems included those that were interaural cross-correlation (IACC) based, relate to localisation of the frontal audio scene, and account for the perceived scene width in front of the listener. Modifying the model for automotive audio systems did not invalidate its use for domestic audio systems. The resulting model predicts the overall spatial

Wood pellet seminar

International Nuclear Information System (INIS)

Aarniala, M.; Puhakka, A.

2001-01-01

The objective of the wood pellet seminar, arranged by OPET Finland and North Karelia Polytechnic, was to deliver information on wood pellets, pellet burners and boilers, heating systems and building, as well as on the activities of wood energy advisors. The first day of the seminar consisted of presentations of equipment and products, and of advisory desks for builders. The second day of the seminar consisted of presentations held by wood pellet experts. Pellet markets, the economy and production, the development of the pellet markets and their problems (in Austria), the economy of heating of real estates by different fuel alternatives, the production, delivery and marketing of wood pellets, the utilization of wood pellet in different utilization sites, the use of wood pellets in detached houses, pellet burners and fireplaces, and conversion of communal real estate houses to use wood pellets were discussed in the presentations. The presentations held in the third day discussed the utilization of wood pellets in power plants, the regional promotion of the production and the use of pellets. The seminar consisted also of visits to pellet manufacturing plant and two pellet burning heating plants

Mixture toxicity of wood preservative products in the fish embryo toxicity test.

Science.gov (United States)

Coors, Anja; Dobrick, Jan; Möder, Monika; Kehrer, Anja

2012-06-01

Wood preservative products are used globally to protect wood from fungal decay and insects. We investigated the aquatic toxicity of five commercial wood preservative products, the biocidal active substances and some formulation additives contained therein, as well as six generic binary mixtures of the active substances in the fish embryo toxicity test (FET). Median lethal concentrations (LC50) of the single substances, the mixtures, and the products were estimated from concentration-response curves and corrected for concentrations measured in the test medium. The comparison of the experimentally observed mixture toxicity with the toxicity predicted by the concept of concentration addition (CA) showed less than twofold deviation for all binary mixtures of the active substances and for three of the biocidal products. A more than 60-fold underestimation of the toxicity of the fourth product by the CA prediction was detected and could be explained fully by the toxicity of one formulation additive, which had been labeled as a hazardous substance. The reason for the 4.6-fold underestimation of toxicity of the fifth product could not be explained unambiguously. Overall, the FET was found to be a suitable screening tool to verify whether the toxicity of formulated wood preservatives can reliably be predicted by CA. Applied as a quick and simple nonanimal screening test, the FET may support approaches of applying component-based mixture toxicity predictions within the environmental risk assessment of biocidal products, which is required according to European regulations. Copyright © 2012 SETAC.

Predicting quality of experience in multimedia streaming

NARCIS (Netherlands)

Menkovski, V.; Oredope, A.; Liotta, A.; Cuadra Sánchez, A.

2009-01-01

Measuring and predicting the user’s Quality of Experience (QoE) of a multimedia stream is the first step towards improving and optimizing the provision of mobile streaming services. This enables us to better understand how Quality of Service (QoS) parameters affect service quality, as it is actually

Blind prediction of natural video quality.

Science.gov (United States)

Saad, Michele A; Bovik, Alan C; Charrier, Christophe

2014-03-01

We propose a blind (no reference or NR) video quality evaluation model that is nondistortion specific. The approach relies on a spatio-temporal model of video scenes in the discrete cosine transform domain, and on a model that characterizes the type of motion occurring in the scenes, to predict video quality. We use the models to define video statistics and perceptual features that are the basis of a video quality assessment (VQA) algorithm that does not require the presence of a pristine video to compare against in order to predict a perceptual quality score. The contributions of this paper are threefold. 1) We propose a spatio-temporal natural scene statistics (NSS) model for videos. 2) We propose a motion model that quantifies motion coherency in video scenes. 3) We show that the proposed NSS and motion coherency models are appropriate for quality assessment of videos, and we utilize them to design a blind VQA algorithm that correlates highly with human judgments of quality. The proposed algorithm, called video BLIINDS, is tested on the LIVE VQA database and on the EPFL-PoliMi video database and shown to perform close to the level of top performing reduced and full reference VQA algorithms.

Knot detection in X-ray images of wood planks using dictionary learning

DEFF Research Database (Denmark)

Hansson, Nils Mattias; Enescu, Alexandru; Brandt, Sami Sebastian

2015-01-01

This paper considers a novel application of x-ray imaging of planks, for the purpose of detecting knots in high quality furniture wood. X-ray imaging allows the detection of knots invisible from the surface to conventional cameras. Our approach is based on texture analysis, or more specifically, ......, discriminative dictionary learning. Experiments show that the knot detection and segmentation can be accurately performed by our approach. This is a promising result and can be directly applied in industrial processing of furniture wood.......This paper considers a novel application of x-ray imaging of planks, for the purpose of detecting knots in high quality furniture wood. X-ray imaging allows the detection of knots invisible from the surface to conventional cameras. Our approach is based on texture analysis, or more specifically...

Projected wood energy impact on US forest wood resources

Energy Technology Data Exchange (ETDEWEB)

Skog, K.E. [USDA Forest Service, Madison, WI (United States)

1993-12-31

The USDA Forest Service has developed long-term projections of wood energy use as part of a 1993 assessment of demand for and supply of resources from forest and range lands in the United States. To assess the impact of wood energy demand on timber resources, a market equilibrium model based on linear programming was developed to project residential, industrial, commercial, and utility wood energy use from various wood energy sources: roundwood from various land sources, primary wood products mill residue, other wood residue, and black liquor. Baseline projections are driven by projected price of fossil fuels compared to price of wood fuels and the projected increase in total energy use in various end uses. Wood energy use is projected to increase from 2.67 quad in 1986 to 3.5 quad in 2030 and 3.7 quad in 2040. This is less than the DOE National Energy Strategy projection of 5.5 quad in 2030. Wood energy from forest sources (roundwood) is projected to increase from 3.1 billion (10{sup 9}) ft{sup 3} in 1986 to 4.4. billion ft{sup 3} in 2030 and 4.8 billion ft{sup 3} in 2040 (88, 124 and 136 million m{sup 3}, respectively). This rate of increase of roundwood use for fuel -- 0.8 percent per year -- is virtually the same as the projected increase rate for roundwood for pulpwood. Pulpwood roundwood is projected to increase from 4.2 billion ft{sup 3} in 1986 to 6.0 billion ft{sup 3} in 2030 and 6.4 billion ft{sup 3} in 2040 (119, 170 and 183 million m{sup 3}, respectively).

Microbuckling compression failure of a radiation-induced wood/polymer composite

International Nuclear Information System (INIS)

Boey, F.Y.C.

1990-01-01

A wood/polymer composite was produced by impregnating Ramin wood with methyl methacrylate monomer and subsequently polymerizing it by gamma irradiation. To assess the improvement in compression strength of the wood caused by the polymer impregnation, a microbuckling compression failure mechanism was used to model the compression failure of the composite. Such a mechanism was found to predict a linear relationship between the compression strength and the percentage polymer impregnation (by weight). Uniaxial compression test results at 45(±5)% and 90(±5)% relative humidity levels, after being statistically analysed, showed that such a linear relationship was valid for up to 100% polymer impregnation. (author)

Online resources for the identification of North American wood decay fungi

Science.gov (United States)

Jessie A. Glaeser

2012-01-01

The ability to identify wood decay fungi is an important skill for an arborist. Knowing which fungus is colonizing a tree can be used to better assess the type, amount, and position of decay in the tree, and its subsequent effects on wood strength. Distinguishing species of fungi that colonize sapwood, heartwood, or roots can provide information to improve the quality...

Lateral-Torsional Buckling Instability Caused by Individuals Walking on Wood Composite I-Joists

Science.gov (United States)

Villasenor Aguilar, Jose Maria

Recent research has shown that a significant number of the falls from elevation occur when laborers are working on unfinished structures. Workers walking on wood I-joists on roofs and floors are prone to fall hazards. Wood I-joists have been replacing dimension lumber for many floor systems and a substantial number of roof systems in light-frame construction. Wood I-joists are designed to resist axial stresses on the flanges and shear stresses on the web while minimizing material used. However, wood I-joists have poor resistance to applied lateral and torsional loads and are susceptible to lateral-torsional buckling instability. Workers walking on unbraced or partially braced wood I-joists can induce axial and lateral forces as well as twist. Experimental testing demonstrated that workers cause lateral-torsional buckling instability in wood I-joists. However, no research was found related to the lateral-torsional buckling instability induced by individuals walking on the wood I-joists. Furthermore, no research was found considering the effects of the supported end conditions and partial bracing in the lateral-torsional buckling instability of wood I-joists. The goal of this research was to derive mathematical models to predict the dynamic lateral-torsional buckling instability of wood composite I-joists loaded by individuals walking considering different supported end conditions and bracing system configurations. The dynamic lateral-torsional buckling instability was analyzed by linearly combining the static lateral-torsional buckling instability with the lateral bending motion of the wood Ijoists. Mathematical models were derived to calculate the static critical loads for the simply supported end condition and four wood I-joist hanger supported end conditions. Additionally, mathematical models were derived to calculate the dynamic maximum lateral displacements and positions of the individual walking on the wood Ijoists for the same five different supported end

Investigation and Evaluation on Influence of Machining (CNC Conditions on Surface Quality of Paulownia Wood

Directory of Open Access Journals (Sweden)

Mohammad Aghajani

2012-01-01

Full Text Available The aim of this study was to investigate the effective factors on surface quality of paulownia wood during machining by advanced computer numerical controled (CNC machine. For this aim paulownia logs were provided and were converted to proper sizes (2.5 x 10 x 15 cm and then air dried. The Variable of this study were cutting speed (8.37 and 15.07 m/s, feeding rate (6 and 12 m/min, cutting depth (1and 5 mm, cutting method (down and up-milling and cutting pattern (tangential and radial. Roughness of cut specimens edge were evaluated by profilometer method according to ISO 13565 standard. For evaluation of surface quality, average roughness (Ra, maximum roughness (R max, valley roughness (Rv and peak roughness (Rp were used. Degrees of effectiveness of the parameters were evaluated by fractional factorial design as completely random design at confidence level of 95%. The result showed that cutting speed, cutting method and feed rate are influencive factors on surface quality of machined specimens and their effects were significant. With increasing cutting speed and decreasing feeding rate the roughness decreased and surface quality improved. In up-milling cutting method, degree of roughness was higher and consequently surface quality was inferior. It is to be noted that cutting method in comparison to other factors had the high influence on surface quality. The rest variables did now have independent influence on surface quality at 95% Confidence level. This study for achieving the optimum surface quality recommends that cutting speed of 15.07 m/s, feeding rate of 6 m/min, cutting method of down-milling and cutting depth of 1 mm for tangential cross section.

Importance of small-scale wood combustion for the air quality at Lycksele and Vaexjoe

International Nuclear Information System (INIS)

Johansson, C.; Hansson, H.C.; Stroem, Johan; Hedberg, Emma; Olivares, Gustavo; Karlsson, Hans; Wideqvist, Ulla

2005-02-01

This report focuses on three different issues: 1. A characterisation of the carbonaceous fraction of the aerosols in Lycksele and Vaexjoe during the campaigns undertaken within the BHM programme in 2002 and 2003. 2. A more detailed source receptor analysis have been undertaken. The wood combustion source is compared with estimates using levoglucosan as tracer. 3. A chemical mass balance of the particle mass has been attempted. A comparison between different methods shows that soot measurements using the integrating plate method (light absorption) provides a very good estimate of the temporal variations of the elemental and organic carbon concentrations. In this case EC and OC concentrations were determined by heating a quartz filter and detection of evolved CO 2 . The concentrations of PM 10 , PM 2.5 and PM 1 are often due to other sources than those that determine the soot levels. In particular occasionally there are very high levels of road dust particles which contain negligible amounts of carbonaceous compounds. At the site Norrmalm, Lycksele also road traffic contribute to the soot levels as indicated by the good correlation between soot and NO x concentrations. Based on a linear relationship between soot concentrations and NO x levels at a road side location close to a high-way just North of Stockholm, an emission factor for soot of 20 mg/vkm was determined. This is much lower than the emission factor for PM 10 obtained at the same location, 550 mg/vkm. In Lycksele the main part of the particle mass was organic and elemental Carbon, almost 40%. Of this, the tracer levoglucosan, made up about 30%. This was very different compared to Vaexjoe, where EC+OC was only 20% of the total PM and levoglucosan was only 6% of the EC and OC part. This confirms that wood-burning is a much more important source in Lycksele as compared to Vaexjoe. Another significant difference between Lycksele and Vaexjoe was that the sum of sulphate, nitrate and ammonium constituted around

A Meta-Heuristic Applying for the Transportation of Wood Raw Material

Directory of Open Access Journals (Sweden)

Erhan Çalışkan

2009-04-01

Full Text Available Primary products in Turkish forestry are wood material. Thus, an operational organization is necessary to transport these main products to depots and then to the consumers without quality and volume loss. This organization starts from harvesting area in the stand and continues to roadside depots or ramps and to main depots and even to manufactures from there. The computer-assisted models, which aim to examine the optimum path in transportation, can be utilized in solving this quite complex problem. In this study, an evaluation has been performed in importance and current status of transporting wood material, classification of wood transportation, computer-assisted heuristic and meta-heuristic methods, and possibilities of using these methods in transportation of wood materials.

Finishing of wood

Science.gov (United States)

R. Sam Williams

1999-01-01

The primary function of any wood finish (paint, varnish, and stain, for example) is to protect the wood surface, help maintain a certain appearance, and provide a cleanable surface. Although wood can be used both outdoors and indoors without finishing, unfinished wood surfaces exposed to the weather change color, are roughened by photodegradation and surface checking,...

The Wood-Growth-and-Burial Process (WGBP) Permanent Wood Sequestration to Solve the Global Carbon Dioxide Problem

Science.gov (United States)

Scholz, F.; Hasse, U.

2008-12-01

Among all global environmental problems there is one which dominates over all others: this is the excessive release of carbon dioxide due to burning of fossil fuels like coal, oil, and gas. The only way to achieve a permanent removal of anthropogenic CO2 must make use of photosynthesis since, so-far, no other technology is able to bind the necessary huge amounts of carbon. Therefore, we propose to grow wood on any available areas, and to bury the wood under anaerobic conditions, e.g., in emptied open pits of coal mining, any other available pits, and possibly also in emptied underground mines. At these places the wood will keep for practically unlimited times, undergoing only very slow carbonization reactions. Simple calculations allow concluding that humans could already now scavenge even all the released CO2, but a more realistic goal may be to bind 20, 30, or 60 percent. This is more a political question than a scientific one. General features of the WGBP are: The growth of woods will transform deforested areas and fallow land to some kind of natural vegetation with the accompanying positive side effects of restoring biotopes, improving the water balance and thus also improving the climate. The growth of woods will produce enormous amounts of oxygen and thus it will add to a sound oxygen balance. It will improve the air quality because of the filtering effect of woods. The growth of woods will improve the soil quality because leaves and roots will stay on and in the ground when the wood is harvested. The WGBP will create jobs in areas where there is an urgent demand for these. The WGBP will offer the opportunity to re-cultivate open pit mining areas. The WGBP will offer the possibility to fill underground mines in a way to prevent earth quakes caused by collapsing mine shafts. The WGBP will enable mankind to survive the time span ahead of us in which mankind will still use fossil fuels. The WGBP can be easily financed by societies via very small additional taxes

Pristine Early Eocene wood buried deeply in kimberlite from northern Canada.

Science.gov (United States)

Wolfe, Alexander P; Csank, Adam Z; Reyes, Alberto V; McKellar, Ryan C; Tappert, Ralf; Muehlenbachs, Karlis

2012-01-01

We report exceptional preservation of fossil wood buried deeply in a kimberlite pipe that intruded northwestern Canada's Slave Province 53.3±0.6 million years ago (Ma), revealed during excavation of diamond source rock. The wood originated from forest surrounding the eruption zone and collapsed into the diatreme before resettling in volcaniclastic kimberlite to depths >300 m, where it was mummified in a sterile environment. Anatomy of the unpermineralized wood permits conclusive identification to the genus Metasequoia (Cupressaceae). The wood yields genuine cellulose and occluded amber, both of which have been characterized spectroscopically and isotopically. From cellulose δ(18)O and δ(2)H measurements, we infer that Early Eocene paleoclimates in the western Canadian subarctic were 12-17°C warmer and four times wetter than present. Canadian kimberlites offer Lagerstätte-quality preservation of wood from a region with limited alternate sources of paleobotanical information.

Congeners in sugar cane spirits aged in casks of different woods.

Science.gov (United States)

Bortoletto, Aline M; Alcarde, André R

2013-08-15

The profile of volatile compounds and aging markers in sugar cane spirits aged for 36 months in casks made of 10 types of wood were studied. The ethanol content, volatile acidity, aldehydes, esters, higher alcohols, and methanol were determined. In addition, gallic, vanilic and syringic acids, siringaldehyde, coniferaldehyde, sinapaldehyde, vanillin, 5-hydroxymethylfurfural and furfural were identified and quantified. The profile of volatile compounds characterised aging in each type of wood. The beverage aged in oak cask achieved the highest contents of maturation-related congeners. The Brazilian woods, similar to oak, were jequitibá rosa and cerejeira, which presented the highest contents of some maturation-related compounds, such as vanillin, vanilic acid, syringaldehyde and sinapaldehyde. Although oak wood conferred more chemical complexity to the beverage, Brazilian woods, singly or complementarily, present potential for spirit characterisation and for improving the quality of sugar cane spirits. Copyright © 2013 Elsevier Ltd. All rights reserved.

Wood fuels utilization in Central Europe - the wood fuels consumption and the targets of utilization

International Nuclear Information System (INIS)

Alakangas, E.

1999-01-01

Following subjects are discussed in this presentation: The share of bioenergy of the total energy consumption in EU region; the wood fuels consumption in EU region in 1995; the division of bioenergy utilization (households, wood- based district heating, wood consumption in industry, power generation from wood and residues, biofuels, biogas and sludges); wood fuels consumption in households in EU countries in 1995; wood consumption in France; the additional wood fuel consumption potential in France; Blan bois - wood energy program; French wood energy markets; German wood energy markets; energy consumption in Germany; wood consumption in Bavaria; the wood fuels potential in Bavaria; wood fuels consumption in households in Bavaria; wood fuels consumption for district heating in Bavaria; fuel prices in Bavaria; Environmental regulations in Germany; small boiler markets in Germany; Energy consumption in Austria; small-scale utilization of wood fuels; utilization of wood energy. (Slides, additional information from the author)

Wood construction and magnetic characteristics of impregnated type magnetic wood

International Nuclear Information System (INIS)

Oka, Hideo; Hojo, Atsushi; Seki, Kyoushiro; Takashiba, Toshio

2002-01-01

The results of experiments involving the AC and DC magnetic characteristics of impregnated type magnetic wood were studied by taking into consideration the wood construction and fiber direction. The experimental results show that the sufficient amount of impregnated magnetic fluid varies depending on the fiber direction and length, and the grain face of the wood material. The impregnated type magnetic wood sample that is fully impregnated by magnetic fluid has a 60% saturation magnetization compared to the saturation magnetization of magnetic fluid. Samples for which the wood fiber direction was the same as the direction of the magnetic path had a higher magnetization intensity and permeability

Colorimetry as grouping tool of eucalyptus clones wood

Directory of Open Access Journals (Sweden)

Márcio da Fonseca Martins

2015-12-01

Full Text Available The homogeneity of wood color in a batch to be marketed is of fundamental importance, as it will reflect in products quality resulting from its processing. In this context, this study aimed to evaluate, through colorimetric technique, the colorimetric parameters of Eucalyptus spp. wood from 25 clones and classify them into groups, according to color similarity degree. It was determined the lightness (L*, red-green color coordinate (a*, yellow-blue chromatic coordinate (b*, chromaticity (C* and ink angle (h. Radial and tangential faces and three positions in the radial direction were characterized using a colorimeter. Comparing to tangential planes, the results showed that radial plane presented larger values of L* and h in wood near the bark. Furthermore, it was observed higher values of L* in samples from intermediate radial positions. Finally, it was found that, as radial growth ocurred, developed timber showed less intense yellow shades. The definition of the wood color tones will be useful in timber market in the homogenization of their products, which will facilitate their marketing.

Predicting the perceived sound quality of frequency-compressed speech.

Directory of Open Access Journals (Sweden)

Rainer Huber

Full Text Available The performance of objective speech and audio quality measures for the prediction of the perceived quality of frequency-compressed speech in hearing aids is investigated in this paper. A number of existing quality measures have been applied to speech signals processed by a hearing aid, which compresses speech spectra along frequency in order to make information contained in higher frequencies audible for listeners with severe high-frequency hearing loss. Quality measures were compared with subjective ratings obtained from normal hearing and hearing impaired children and adults in an earlier study. High correlations were achieved with quality measures computed by quality models that are based on the auditory model of Dau et al., namely, the measure PSM, computed by the quality model PEMO-Q; the measure qc, computed by the quality model proposed by Hansen and Kollmeier; and the linear subcomponent of the HASQI. For the prediction of quality ratings by hearing impaired listeners, extensions of some models incorporating hearing loss were implemented and shown to achieve improved prediction accuracy. Results indicate that these objective quality measures can potentially serve as tools for assisting in initial setting of frequency compression parameters.

Achievements in the utilzation of poplar wood : guideposts for the future : [abstract

Science.gov (United States)

John J. Balatinecz; Andre. Leclercq; David E. Kretschmann

2000-01-01

Poplar wood is suitable and is utilized for a broad range of forest products worldwide. The utilization of any species is governed by a number of factors, such as basic wood properties, overall quality, quantity and price of the resource, available processing technologies, local as well as international market conditions for the products, and the availability and price...

Wood preservatives and pressure-treated wood: considerations for historic-preservation projects

Science.gov (United States)

Ronald W. Anthony; Stan T. Lebow

2015-01-01

Wood, an abundant resource throughout most of the world, has been used as a building material for thousands of years. Many historic buildings have been built primarily of wood, and masonry and stone buildings generally have wood elements, both structural and architectural. As a biological material, wood is both remarkably complex and yet quite durable if well...

Processing of the wood angelim pedra (Hymenolobium petraeum

Directory of Open Access Journals (Sweden)

Adjenane Corrêa Taques

2016-08-01

Full Text Available This study aimed to verify the behavior of wood Angelim stone (Hymenolobium petraeum Ducke submitted to the machining process. The study was developed in a carpentry shop in the city of Alta Floresta-MT. 36 boards with dimensions of 150 cm x 13.5 cm x 2.5 cm, length, width and thickness were randomly selected respectively for machining tests. The tests were developed according to the machinability of equipment used by the furniture industry, planing, sanding, drill and split by nail. 8 boards of wood in the stack were selected randomly to determine the moisture, according to 7190 (ABNT, 1997. The notes used for evaluation of defects resulting in the wood during the machining processes were assigned according to ASTM D 1666 (1987. It was observed that the type of angelim stone showed excellent performance in grinding tests, no scratch on the surface piece a of the burring parts and the parts free from defects, with the burning of wood. In cracking test for nail had a good performance, because it showed cracks with the insertion of the nail and planing test a regular performance, with pullout grain, surface arrepiamento and pullout chip. Wood Angelim stone responds with quality to the machining processes in planing, sanding, drill and split by nail.

Integrated control of wood destroying basidiomycetes combining Cu-based wood preservatives and Trichoderma spp.

Science.gov (United States)

Ribera, Javier; Fink, Siegfried; Bas, Maria Del Carmen; Schwarze, Francis W M R

2017-01-01

The production of new generation of wood preservatives (without addition of a co-biocide) in combination with an exchange of wood poles on identical sites with high fungal inoculum, has resulted in an increase of premature failures of wood utility poles in the last decades. Wood destroying basidiomycetes inhabiting sites where poles have been installed, have developed resistance against wood preservatives. The objective of the in vitro studies was to identify a Trichoderma spp. with a highly antagonistic potential against wood destroying basidiomycetes that is capable of colonizing Cu-rich environments. For this purpose, the activity of five Trichoderma spp. on Cu-rich medium was evaluated according to its growth and sporulation rates. The influence of the selected Trichoderma spp. on wood colonization and degradation by five wood destroying basidiomycetes was quantitatively analyzed by means of dry weight loss of wood specimens. Furthermore, the preventative effect of the selected Trichoderma spp. in combination with four Cu-based preservatives was also examined by mass loss and histological changes in the wood specimens. Trichoderma harzianum (T-720) was considered the biocontrol agent with higher antagonistic potential to colonize Cu-rich environments (up to 0.1% CuSO4 amended medium). T. harzianum demonstrated significant preventative effect on wood specimens against four wood destroying basidiomycetes. The combined effect of T. harzianum and Cu-based wood preservatives demonstrated that after 9 months incubation with two wood destroying basidiomycetes, wood specimens treated with 3.8 kg m-3 copper-chromium had weight losses between 55-65%, whereas containers previously treated with T. harzianum had significantly lower weight losses (0-25%). Histological studies on one of the wood destroying basidiomycetes revealed typical decomposition of wood cells by brown-rot fungi in Cu-impregnated samples, that were notably absent in wood specimens previously exposed to T

Integrated control of wood destroying basidiomycetes combining Cu-based wood preservatives and Trichoderma spp.

Directory of Open Access Journals (Sweden)

Javier Ribera

Full Text Available The production of new generation of wood preservatives (without addition of a co-biocide in combination with an exchange of wood poles on identical sites with high fungal inoculum, has resulted in an increase of premature failures of wood utility poles in the last decades. Wood destroying basidiomycetes inhabiting sites where poles have been installed, have developed resistance against wood preservatives. The objective of the in vitro studies was to identify a Trichoderma spp. with a highly antagonistic potential against wood destroying basidiomycetes that is capable of colonizing Cu-rich environments. For this purpose, the activity of five Trichoderma spp. on Cu-rich medium was evaluated according to its growth and sporulation rates. The influence of the selected Trichoderma spp. on wood colonization and degradation by five wood destroying basidiomycetes was quantitatively analyzed by means of dry weight loss of wood specimens. Furthermore, the preventative effect of the selected Trichoderma spp. in combination with four Cu-based preservatives was also examined by mass loss and histological changes in the wood specimens. Trichoderma harzianum (T-720 was considered the biocontrol agent with higher antagonistic potential to colonize Cu-rich environments (up to 0.1% CuSO4 amended medium. T. harzianum demonstrated significant preventative effect on wood specimens against four wood destroying basidiomycetes. The combined effect of T. harzianum and Cu-based wood preservatives demonstrated that after 9 months incubation with two wood destroying basidiomycetes, wood specimens treated with 3.8 kg m-3 copper-chromium had weight losses between 55-65%, whereas containers previously treated with T. harzianum had significantly lower weight losses (0-25%. Histological studies on one of the wood destroying basidiomycetes revealed typical decomposition of wood cells by brown-rot fungi in Cu-impregnated samples, that were notably absent in wood specimens

Wood composites

Science.gov (United States)

Lars Berglund; Roger M. Rowell

2005-01-01

A composite can be defined as two or more elements held together by a matrix. By this definition, what we call “solid wood” is a composite. Solid wood is a three-dimensional composite composed of cellulose, hemicelluloses and lignin (with smaller amounts of inorganics and extractives), held together by a lignin matrix. The advantages of developing wood composites are (...

Bacteria in decomposing wood and their interactions with wood-decay fungi.

Science.gov (United States)

Johnston, Sarah R; Boddy, Lynne; Weightman, Andrew J

2016-11-01

The fungal community within dead wood has received considerable study, but far less attention has been paid to bacteria in the same habitat. Bacteria have long been known to inhabit decomposing wood, but much remains underexplored about their identity and ecology. Bacteria within the dead wood environment must interact with wood-decay fungi, but again, very little is known about the form this takes; there are indications of both antagonistic and beneficial interactions within this fungal microbiome. Fungi are hypothesised to play an important role in shaping bacterial communities in wood, and conversely, bacteria may affect wood-decay fungi in a variety of ways. This minireview considers what is currently known about bacteria in wood and their interactions with fungi, and proposes possible associations based on examples from other habitats. It aims to identify key knowledge gaps and pressing questions for future research. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Development and Validation of a Simulation Model for the Temperature Field during High-Frequency Heating of Wood

Directory of Open Access Journals (Sweden)

Haojie Chai

2018-06-01

Full Text Available In the process of applying high-frequency heating technology to wood drying, controlling the material temperature affects both drying speed and drying quality. Therefore, research on the heat transfer mechanism of high-frequency heating of wood is of great significance. To study the heat transfer mechanism of high-frequency heating, the finite element method was used to establish and solve the wood high-frequency heating model, and experimental verification was carried out. With a decrease in moisture content, the heating rate decreased, then increased, and then decreased again. There was no obvious linear relationship between the moisture content and heating rate; the simulation accuracy of the heating rate was higher in the early and later drying stages and slightly lower near the fiber saturation point. For the central section temperature distribution, the simulation and actual measurement results matched poorly in the early drying stage because the model did not fully consider the differences in the moisture content distribution of the actual test materials. In the later drying stage, the moisture content distribution of the test materials became uniform, which was consistent with the model assumptions. Considering the changes in heating rate and temperature distribution, the accuracy of the model is good under the fiber saturation point, and it can be used to predict the high-frequency heating process of wood.

Pristine Early Eocene wood buried deeply in kimberlite from northern Canada.

Directory of Open Access Journals (Sweden)

Alexander P Wolfe

Full Text Available We report exceptional preservation of fossil wood buried deeply in a kimberlite pipe that intruded northwestern Canada's Slave Province 53.3±0.6 million years ago (Ma, revealed during excavation of diamond source rock. The wood originated from forest surrounding the eruption zone and collapsed into the diatreme before resettling in volcaniclastic kimberlite to depths >300 m, where it was mummified in a sterile environment. Anatomy of the unpermineralized wood permits conclusive identification to the genus Metasequoia (Cupressaceae. The wood yields genuine cellulose and occluded amber, both of which have been characterized spectroscopically and isotopically. From cellulose δ(18O and δ(2H measurements, we infer that Early Eocene paleoclimates in the western Canadian subarctic were 12-17°C warmer and four times wetter than present. Canadian kimberlites offer Lagerstätte-quality preservation of wood from a region with limited alternate sources of paleobotanical information.

Non_standard Wood

DEFF Research Database (Denmark)

Tamke, Martin

. Using parametric design tools and computer controlled production facilities Copenhagens Centre for IT and Architecture undertook a practice based research into performance based non-standard element design and mass customization techniques. In close cooperation with wood construction software......, but the integration of traditional wood craft techniques. The extensive use of self adjusting, load bearing wood-wood joints contributed to ease in production and assembly of a performance based architecture....

Modeling decay rates of dead wood in a neotropical forest.

Science.gov (United States)

Hérault, Bruno; Beauchêne, Jacques; Muller, Félix; Wagner, Fabien; Baraloto, Christopher; Blanc, Lilian; Martin, Jean-Michel

2010-09-01

Variation of dead wood decay rates among tropical trees remains one source of uncertainty in global models of the carbon cycle. Taking advantage of a broad forest plot network surveyed for tree mortality over a 23-year period, we measured the remaining fraction of boles from 367 dead trees from 26 neotropical species widely varying in wood density (0.23-1.24 g cm(-3)) and tree circumference at death time (31.5-272.0 cm). We modeled decay rates within a Bayesian framework assuming a first order differential equation to model the decomposition process and tested for the effects of forest management (selective logging vs. unexploited), of mode of death (standing vs. downed) and of topographical levels (bottomlands vs. hillsides vs. hilltops) on wood decay rates. The general decay model predicts the observed remaining fraction of dead wood (R2 = 60%) with only two biological predictors: tree circumference at death time and wood specific density. Neither selective logging nor local topography had a differential effect on wood decay rates. Including the mode of death into the model revealed that standing dead trees decomposed faster than downed dead trees, but the gain of model accuracy remains rather marginal. Overall, these results suggest that the release of carbon from tropical dead trees to the atmosphere can be simply estimated using tree circumference at death time and wood density.

Thermal Properties of Wood-Plastic Composites Prepared from Hemicellulose-extracted Wood Flour

Directory of Open Access Journals (Sweden)

A.A. Enayati

2013-01-01

Full Text Available Hemicellulose of Southern Yellow Pine wood spices was extracted by pressurized hot water at three different temperatures: 140°C, 155°C and 170°C. Compounding with PP (polypropylene was performed by extrusion after preparing wood flour and sieving to determine its mesh size. The ratio of wood to polymer was 50:50 based on oven-dry weight of wood flour. All extraction treatments and control samples were compounded under two sets of conditions, without and with 2% MAPP as coupling agent. Injection molding was used to make tensile test samples (dogbone from the pellets made by extrusion. Thermal properties of wood-plastic composites were studied by TGA and DSC while the thermal stability of pretreated wood flours, PP and MAPP were studied by TGA as well. The greater weight loss of wood materials was an indication that higher treatment temperature increases the extractability of hemicellulose. The removal of hemicellulose by extraction improves thermal stability of wood flour, especially for extraction at 170°C. Wood-plastic composites made from extracted fibers at 170°C showed the highest thermal stability. Coupling agent did not have a significant effect on thermal stability but it improved the degree of crystallinity of the composites.Surface roughness of wood fiber increased after treatment. Extraction of hemicellulose increased the degree of crystallinity but it was not significant except for samples from treated wood flour at 170°C and with MAPP.

Audiovisual quality assessment and prediction for videotelephony

CERN Document Server

Belmudez, Benjamin

2015-01-01

The work presented in this book focuses on modeling audiovisual quality as perceived by the users of IP-based solutions for video communication like videotelephony. It also extends the current framework for the parametric prediction of audiovisual call quality. The book addresses several aspects related to the quality perception of entire video calls, namely, the quality estimation of the single audio and video modalities in an interactive context, the audiovisual quality integration of these modalities and the temporal pooling of short sample-based quality scores to account for the perceptual quality impact of time-varying degradations.

Theoretical analysis of moisture transport in wood as an open porous hygroscopic material

DEFF Research Database (Denmark)

Hozjan, Tomaz; Svensson, Staffan

2010-01-01

Moisture transport in an open porous hygroscopic material such as wood is a complex system of coupled processes. For seasoned wood in natural climate three fully coupled processes active in the moisture transport are readily identified: (1) diffusion of vapor in pores; (2) phase change from one...... state to another, also called moisture sorption; and (3) diffusion of bound water in wood tissue (in the cell wall). A mathematical model for predicting moisture transport in wood for a given condition must at least consider the dominating active processes simultaneously to be considered accurate...... of the three processes on the outcome of the coupled model. Least significant is the bound water diffusion. Based on the results from the sensitivity analyses, a simplified model for moisture transport in wood is proposed....

Developments in undergraduate wood science education at Stellenbosch University, South Africa

OpenAIRE

Rypstra,Tim

2011-01-01

In South Africa, Stellenbosch University (SU) is the designated provider of Bachelor, Master and Doctorate level qualifications in Forestry and Wood Products Science. SU provides educational programs to both mechanical (sawmilling, preservation, composite products, furniture, etc.) and the chemical (pulp & paper) processing sectors. To ensure academic quality, SU regularly has her academic programs assessed externally. In 2000, several changes to the then existing 4 year B.Sc. Wood Scienc...

Lignin-Retaining Transparent Wood.

Science.gov (United States)

Li, Yuanyuan; Fu, Qiliang; Rojas, Ramiro; Yan, Min; Lawoko, Martin; Berglund, Lars

2017-09-11

Optically transparent wood, combining optical and mechanical performance, is an emerging new material for light-transmitting structures in buildings with the aim of reducing energy consumption. One of the main obstacles for transparent wood fabrication is delignification, where around 30 wt % of wood tissue is removed to reduce light absorption and refractive index mismatch. This step is time consuming and not environmentally benign. Moreover, lignin removal weakens the wood structure, limiting the fabrication of large structures. A green and industrially feasible method has now been developed to prepare transparent wood. Up to 80 wt % of lignin is preserved, leading to a stronger wood template compared to the delignified alternative. After polymer infiltration, a high-lignin-content transparent wood with transmittance of 83 %, haze of 75 %, thermal conductivity of 0.23 W mK -1 , and work-tofracture of 1.2 MJ m -3 (a magnitude higher than glass) was obtained. This transparent wood preparation method is efficient and applicable to various wood species. The transparent wood obtained shows potential for application in energy-saving buildings. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Modelling piloted ignition of wood and plastics

NARCIS (Netherlands)

Blijderveen, M.; Bramer, Eduard A.; Brem, Gerrit

2012-01-01

To gain insight in the startup of an incinerator, this article deals with piloted ignition. A newly developed model is described to predict the piloted ignition times of wood, PMMA and PVC. The model is based on the lower flammability limit and the adiabatic flame temperature at this limit. The

Response of Microtermes mycophagus (Isoptera: Termitidae to twenty one wood species

Directory of Open Access Journals (Sweden)

Naeem Iqbal

2015-08-01

Full Text Available The responses of termite species to bait depend upon the quality of the food used in the stations. Woods are the most common food sources for termites but different termite species behave differently to different wood species and types. The knowledge of the preference status of different wood species to a termite species helps in effective monitoring and baiting program. The current study was carried out to evaluate the preference of 21 wood species to the termite, Microtermes mycophagus in the field by no-choice and choice feeding tests. The results indicated silk cotton tree and sacred fig woods as the most preferred wood species with mean mass losses of 71.21 ± 5.09% and 68.38 ± 7.27% in no-choice test and 95.02 ± 1.65% and 91.69 ± 2.07% in choice tests, respectively. White cedar was the least preferred wood species with mean mass losses of 7.49 ± 1.64% and 13.92 ± 1.89% in no choice and choice feeding tests, respectively. Based on present studies, sapwood of silk cotton tree and sacred fig may be used in effective monitoring and baiting program against M. mycophagus.

Kaolin Quality Prediction from Samples: A Bayesian Network Approach

International Nuclear Information System (INIS)

Rivas, T.; Taboada, J.; Ordonez, C.; Matias, J. M.

2009-01-01

We describe the results of an expert system applied to the evaluation of samples of kaolin for industrial use in paper or ceramic manufacture. Different machine learning techniques - classification trees, support vector machines and Bayesian networks - were applied with the aim of evaluating and comparing their interpretability and prediction capacities. The predictive capacity of these models for the samples analyzed was highly satisfactory, both for ceramic quality and paper quality. However, Bayesian networks generally proved to be the most useful technique for our study, as this approach combines good predictive capacity with excellent interpretability of the kaolin quality structure, as it graphically represents relationships between variables and facilitates what-if analyses.

Psychological factors in the diffusion of sustainable technology: a study of Norwegian households' adoption of wood pellet heating

Energy Technology Data Exchange (ETDEWEB)

Sopha, Bertha Maya; Kloeckner, Christian A.

2010-07-01

Full text: This paper aims to understand the determinants of the adoption of wood pellet technology for home heating to identify possible strategies towards the slow diffusion of wood pellet in Norway. A mail survey of 737 Norwegian households was conducted in 2008, involving wood pellet adopters and non wood pellet adopters as respondents. An integrated model combining psychological factors (such as intentions, attitudes, perceived behavioral control, habits and norms), perceived wood pellet heating characteristics, and ecological and basic values is applied to predict the installation of a wood pellet stove retrospectively. Results from a path analysis gain empirical support for the proposed integrated model. Wood pellet heating adoption is mainly predicted by a deliberate decision process starting with the evaluation of heating system characteristics, mediated by attitudes and intentions. Perceived behavioural control and habits pose relevant barriers to the adoption process. The influence of norms and values are indirect and only minor in the given market conditions. The most important heating system characteristics in the analysis were perceived functional reliability and perceived installation and maintenance costs. Possible intervention strategies to speed up wood pellet adoption in Norway are discussed in the last part of the paper. (Author)

Mechanics of Wood Machining

CERN Document Server

Csanády, Etele

2013-01-01

Wood is one of the most valuable materials for mankind, and since our earliest days wood materials have been widely used. Today we have modern woodworking machine and tools; however, the raw wood materials available are continuously declining. Therefore we are forced to use this precious material more economically, reducing waste wherever possible. This new textbook on the “Mechanics of Wood Machining” combines the quantitative, mathematical analysis of the mechanisms of wood processing with practical recommendations and solutions. Bringing together materials from many sources, the book contains new theoretical and experimental approaches and offers a clear and systematic overview of the theory of wood cutting, thermal loading in wood-cutting tools, dynamic behaviour of tool and work piece, optimum choice of operational parameters and energy consumption, the wear process of the tools, and the general regularities of wood surface roughness. Diagrams are provided for the quick estimation of various process ...

National Wood-fuel Programme 2000-2006. Activity Report 2000-2006

International Nuclear Information System (INIS)

2008-01-01

When ADEME launched its Wood-fuel programme throughout all of France in late 1999, its aim was to guide this resource supply chain to maturity and stable development in all user sectors: domestic, multi-family housing, commercial/institutional and industrial applications. To this end the Wood-fuel Programme 2000-2006 was assigned objectives and endowed with significant financial means for studies and coordination in order to support and carry out general-interest projects, piloted by ADEME. The stated goal was to replace fossil fuels, avoid carbon emissions and establish quality assurance standards for household firewood and wood-fired devices. This report presents: 1 - the Wood Energy stakes for the environment, for employment, and for the economy, the biomass energy net benefits; 2 - the Wood Energy key figures: Production and consumption, Single-family homes and wood heating, Breakdown of types of devices used, Sales of wood-fired devices, Number of housing/institutional boilers in use, Number of industrial boilers in use; 3 - the Wood Energy objectives: Domestic heating, Industrial boiler plants, District heating for housing/institutional/commercial uses; 4 - the Wood Energy program operation: Program coordination by ADEME, Partnerships and State-Region planning agreements, 2000-2006 funding system (modified in 2004) and Other financial instruments; 5 - the 2000-2006 assessment: Main results, Conclusions and recommendations, Evaluation contributions: five key points, Evaluation of employment in the solid biofuels supply chain, Supply for community, institutional and commercial boilers; 6 - Information and communication: Initiatives supported or accompanied by ADEME between 2000 and 2004, Publications supported by ADEME. In appendix: fuels and energy content, regional assessments, national research program on bio-energies - PNRB 2006 (Review and stakes, PNRB results in 2006), wood heating R and D, studies funded by ADEME, 2006 ADEME's correspondents, glossary

The principles, procedures and pitfalls in identifying archaeological and historical wood samples.

Science.gov (United States)

Cartwright, Caroline R

2015-07-01

The science of wood anatomy has evolved in recent decades to add archaeological and historical wood to its repertoire of documenting and characterizing modern and fossil woods. The increasing use of online wood anatomy databases and atlases has fostered the adoption of an international consensus regarding terminology, largely through the work of the International Association of Wood Anatomists (IAWA). This review presents an overview for the general reader of the current state of principles and procedures involved in the study of the wood anatomy of archaeological and historical specimens, some of which may be preserved through charring, waterlogging, desiccation or mineral replacement. By means of selected case studies, the review evaluates to what extent varying preservation of wood anatomical characteristics limits the level of identification to taxon. It assesses the role played by increasingly accessible scanning electron microscopes and complex optical microscopes, and whether these, on the one hand, provide exceptional opportunities for high-quality imaging and analysis of difficult samples, but, on the other hand, might be misleading the novice into thinking that advanced technology can be a substitute for specialized botanical training in wood anatomy. © The Author 2015. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Soil-wood interactions

NARCIS (Netherlands)

Wal, van der Annemieke; klein Gunnewiek, Paulien; Boer, de Wietse

2017-01-01

Wood-inhabiting fungi may affect soil fungal communities directly underneath decaying wood via their exploratory hyphae. In addition, differences in wood leachates between decaying tree species may influence soil fungal communities. We determined the composition of fungi in 4-yr old decaying logs

Turning palm leaves into wood: Opportunities for Egypt's rural ...

International Development Research Centre (IDRC) Digital Library (Canada)

2016-04-27

Apr 27, 2016 ... Bedouin women weave handmade baskets, hats, and lamps using dried palm leaves. ... palm tree leaves into hardwood and high-quality wooden products, ... of wood and open doors to job opportunities for rural communities.

Predicting the density of structural timber members in service. The combine use of wood cores and drill resistance data

Directory of Open Access Journals (Sweden)

Morales-Condea, M. J.

2014-09-01

Full Text Available Drilling devices is used to get information about the cross-section properties and internal defects of structural members. Drill resistance is correlated with density which is often used to predict the mechanical properties of timber elements. However in situ a regression curve cannot be obtained and pre-existent curves provides unreliable predictions. The present paper proposes a procedure for in situ “calibration” of drill resistance data. The “calibration” is based on density values from wood cores taken in the close vicinity of drill holes. Two approaches were tested. One approach based on a regression curve built using wood cores density and drill resistance values obtained from a limited number of members. The other approach uses the information of one wood core to “calibrate” the drill resistance profile taken at the same member. Following this procedure a density prediction is obtained showing a low mean percentage error and a medium coefficient of determination.Los dispositivos de perforación se utilizan a menudo para obtener información sobre las propiedades de la sección transversal y defectos internos de los elementos estructurales de madera. La resistencia a la perforación se correlaciona con la densidad que, a menudo, se utiliza para obtener la predicción de las propiedades mecánicas de los elementos de madera. Sin embargo, una curva de regresión no puede ser obtenida in situ y las curvas de preexistentes proporcionan predicciones poco fiables. En el presente trabajo se propone un procedimiento de “calibración” in situ de los datos de resistencia de perforación obtenidos en cada caso. La “calibración” se basa en los valores de densidad de pequeñas probetas de madera tomadas en las inmediaciones de los taladros. Para ello se plantean 2 métodos: Un primer enfoque basado en obtener una curva de regresión a partir de los valores de densidad de pequeñas probetas de madera y los valores de resistencia a

Combustion of Waste Wood. Second phase of the collaboration project on waste wood combustion

International Nuclear Information System (INIS)

Andersson, Annika; Andersson, Christer; Eriksson, Jan; Hemstroem, Bengt; Jungstedt, Jenny; Kling, Aasa; Bahr, Bo von; Ekvall, Annika; Eskilsson, David; Tullin, Claes; Harnevie, Henrik; Sieurin, Jan; Keihaes, Juha; Mueller, Christian; Berg, Magnus; Wikman, Karin

2003-08-01

Combustion of waste wood has during the last decade increased dramatically and this has resulted in a number of Swedish plants using this fuel, e.g. Handeloe P11 (Norrkoeping) and ldbaecken P3 (Nykoeping), and yet other plants that are under construction (e.g. Nynaeshamn). The experience from these plants are that waste wood combustion results in a number of operational problems. To some extent these problems are different compared with the problems related to combustion of other biofuels but the situation is not directly comparable to waste incinerators. The problems are mainly related to slagging and fouling of heat exchanger surfaces and accelerated corrosion at relatively low temperature compared to the situation for ordinary biofuels. In some cases an increase in the emissions of specific substances can also result in difficulties to fulfil the EC-directive on waste combustion. Within previous projects the main problems related to combustion of waste wood have been identified and to some extent the cause of these problems has been clarified. One result of this reported investigation is a deeper understanding of the actual causes of these problems. However, the most important result is a number of recommendations for different measures on how to achieve disturbance-free combustion of waste wood. These recommendations actually summarises the most important possible solutions on how to achieve a disturbance-free operation and a lower maintenance cost for boilers combusting waste wood and can thereby be regarded as a short summery of the whole project: 1) Improving fuel quality by Improved sorting at the source and Sieving of the fuel -> Reducing the amount of metals and chlorine and Separation of fines and thereby reducing the amount of metals. 2) Combustion modifications by Avoiding reducing conditions at the heat exchanger surfaces -> Minimising slagging, fouling and corrosion. 3) Additives or co-combustion by Addition of sulphur with the fuel; Injection of

Wood energy-commercial applications

Science.gov (United States)

Kennel, R. P.

1978-01-01

Wood energy is being widely investigated in many areas of the country because of the many obvious benefits of wood fuel such as the low price per million Btus relative to coal, oil, and gas; the wide availability of noncommercial wood and the proven ability to harvest it; established technology which is reliable and free of pollution; renewable resources; better conservation for harvested land; and the potential for jobs creation. The Southeastern United States has a specific leadership role in wood energy based on its established forest products industry experience and the potential application of wood energy to other industries and institutions. Significant questions about the widespread usage of wood energy are being answered in demonstrations around the country as well as the Southeast in areas of wood storage and bulk handling; high capitalization costs for harvesting and combustion equipment; long term supply and demand contracts; and the economic feasibility of wood energy outside the forest products industry.

Energy wood. Part 2b: Wood pellets and pellet space-heating systems; Holzenergie Teil 2b: Holzpellets und Pelletheizungen / Energie du bois Partie 2b: Granules de bois et installations de chauffage a granules de bois

Energy Technology Data Exchange (ETDEWEB)

Nussbaumer, T. [Verenum, Zuerich (Switzerland)

2002-07-01

The paper gives an overview on pellet utilization including all relevant process steps: Potential and properties of saw dust as raw material, pellet production with drying and pelletizing, standardization of wood pellets, storage and handling of pellets, combustion of wood pellets in stoves and boilers and applications for residential heating. In comparison to other wood fuels, wood pellets show several advantages: Low water content and high heating value, high energy density, and homogeneous properties thus enabling stationary combustion conditions. However, quality control is needed to ensure constant properties of the pellets and to avoid the utilization of contaminated raw materials for the pellet production. Typical data of efficiencies and emissions of pellet stoves and boilers are given and a life cycle analysis (LCA) of wood pellets in comparison to log wood and wood chips is described. The LCA shows that wood pellets are advantageous thanks to relatively low emissions. Hence, the utilization of wood pellet is proposed as a complementary technology to the combustion of wood chips and log wood. Finally, typical fuel cost of wood pellets in Switzerland are given and compared with light fuel oil. (author)

Simulated nitrogen deposition affects wood decomposition by cord-forming fungi.

Science.gov (United States)

Bebber, Daniel P; Watkinson, Sarah C; Boddy, Lynne; Darrah, Peter R

2011-12-01

Anthropogenic nitrogen (N) deposition affects many natural processes, including forest litter decomposition. Saprotrophic fungi are the only organisms capable of completely decomposing lignocellulosic (woody) litter in temperate ecosystems, and therefore the responses of fungi to N deposition are critical in understanding the effects of global change on the forest carbon cycle. Plant litter decomposition under elevated N has been intensively studied, with varying results. The complexity of forest floor biota and variability in litter quality have obscured N-elevation effects on decomposers. Field experiments often utilize standardized substrates and N-levels, but few studies have controlled the decay organisms. Decomposition of beech (Fagus sylvatica) blocks inoculated with two cord-forming basidiomycete fungi, Hypholoma fasciculare and Phanerochaete velutina, was compared experimentally under realistic levels of simulated N deposition at Wytham Wood, Oxfordshire, UK. Mass loss was greater with P. velutina than with H. fasciculare, and with N treatment than in the control. Decomposition was accompanied by growth of the fungal mycelium and increasing N concentration in the remaining wood. We attribute the N effect on wood decay to the response of cord-forming wood decay fungi to N availability. Previous studies demonstrated the capacity of these fungi to scavenge and import N to decaying wood via a translocating network of mycelium. This study shows that small increases in N availability can increase wood decomposition by these organisms. Dead wood is an important carbon store and habitat. The responses of wood decomposers to anthropogenic N deposition should be considered in models of forest carbon dynamics.

Embryo quality predictive models based on cumulus cells gene expression

Directory of Open Access Journals (Sweden)

Devjak R

2016-06-01

Full Text Available Since the introduction of in vitro fertilization (IVF in clinical practice of infertility treatment, the indicators for high quality embryos were investigated. Cumulus cells (CC have a specific gene expression profile according to the developmental potential of the oocyte they are surrounding, and therefore, specific gene expression could be used as a biomarker. The aim of our study was to combine more than one biomarker to observe improvement in prediction value of embryo development. In this study, 58 CC samples from 17 IVF patients were analyzed. This study was approved by the Republic of Slovenia National Medical Ethics Committee. Gene expression analysis [quantitative real time polymerase chain reaction (qPCR] for five genes, analyzed according to embryo quality level, was performed. Two prediction models were tested for embryo quality prediction: a binary logistic and a decision tree model. As the main outcome, gene expression levels for five genes were taken and the area under the curve (AUC for two prediction models were calculated. Among tested genes, AMHR2 and LIF showed significant expression difference between high quality and low quality embryos. These two genes were used for the construction of two prediction models: the binary logistic model yielded an AUC of 0.72 ± 0.08 and the decision tree model yielded an AUC of 0.73 ± 0.03. Two different prediction models yielded similar predictive power to differentiate high and low quality embryos. In terms of eventual clinical decision making, the decision tree model resulted in easy-to-interpret rules that are highly applicable in clinical practice.

Who's Counting Dead Wood ?

OpenAIRE

Woodall, C. W.; Verkerk, H.; Rondeux, Jacques; Ståhl, G.

2009-01-01

Dead wood in forests is a critical component of biodiversity, carbon and nutrient cycles, stand structure, and fuel loadings. Until recently, very few countries have conducted systematic inventories of dead wood resources across their forest lands. This may be changing as an increasing number of countries implement dead wood inventories. A recent survey looks at the status and attributes of forest dead wood inventories in over 60 countries. About 13 percent of countries inventory dead wood gl...

Diversity of macro-detritivores in dead wood is influenced by tree species, decay stage and environment

NARCIS (Netherlands)

Zuo, Juan; Fonck, Myrthe; van Hal, Jurgen; Cornelissen, J. Hans C.; Berg, Matty P.

Diplopoda (millipedes) and Isopoda (woodlice) are among the most abundant macro-detritivores in temperate forests. These key regulators of plant litter decomposition are influenced by habitat and substrate quality, including that of dead wood. Dead wood provides shelter and resources to

Diversity of macro-detritivores in dead wood is influenced by tree species, decay stage and environment

NARCIS (Netherlands)

Zuo, J.; Fonck, M.; van Hal, J.R.; Cornelissen, J.H.C.; Berg, M.P.

2014-01-01

Diplopoda (millipedes) and Isopoda (woodlice) are among the most abundant macro-detritivores in temperate forests. These key regulators of plant litter decomposition are influenced by habitat and substrate quality, including that of dead wood. Dead wood provides shelter and resources to

Heating with wood. A guide to clean and proper heating; Heizen mit Holz. Ein Ratgeber zum richtigen und sauberen Heizen

Energy Technology Data Exchange (ETDEWEB)

Behnke, Anja [Umweltbundesamt, Dessau (Germany); Kemper, Bernd-Michael [Landesanstalt fuer Umwelt, Messungen und Naturschutz Baden-Wuerttemberg (LUBW), Karlsruhe (Germany)

2013-01-15

When correctly used, wood is an eco-friendly fuel. By using well-processed wood from local sources in a properly handled modern fireplace, you can enjoy the cosy warmth from your wood-burning stove or boiler without causing significant environmental damage. The environment and your neighbours will be grateful for this. This brochure is intended to give you tips on how to properly operate a wood-based heating system - in technical terms referred to as a small combustion installation. Especially the burning of poor quality wood in old and insufficiently maintained stoves and unfavourable combustion conditions will result in the emission of unnecessarily high levels of greenhouse gases having adverse effects on the climate, and pollutants detrimental to your health. Particularly in urban agglomerations and valleys, the air quality is affected by wood heating systems due to low chimneys. Often, neighbours will feel annoyed.

Liquefaction of torrefied wood using microwave irradiation

Science.gov (United States)

Mengchao Zhou; Thomas Eberhardt; Pingping Xin; Chung-Yun Hse; Hui Pan

2016-01-01

Torrefaction is an effective pretreatment method to improve the uniformity and quality of lignocellulosic biomass before further thermal processing (e.g., gasification, combustion). The objective of this study was to determine the impacts of torrefaction as a pretreatment before liquefaction. Wood chips were torrefied for 2 h at three different temperatures (230, 260,...

Inventory of contaminants in waste wood; Inventering av foeroreningar i returtrae

Energy Technology Data Exchange (ETDEWEB)

Jermer, Joeran; Ekvall, Annika; Tullin, Claes [Swedish National Testing and Research Inst., Boraas (Sweden)

2001-03-01

problems. Metal objects of zinc, brass and aluminium are considered to be particularly troublesome as they may plug primary air openings. PVC residues may cause considerably higher levels of chlorine in waste wood. Chemical analyses indicate that the distribution in levels of impurities varies a lot between deliveries of waste wood. Difficulties to take representative samples probably contribute to this. The knowledge of the contents of different types of waste wood (surface treated wood, preservative-treated, panels, furniture etc) in the waste wood flow is only fragmentary. Most certainly, surface treated (painted, stained etc) wood constitute the highest proportion. Preservative-treated wood, with the exception of railway sleepers and poles, is estimated to constitute approximately 5% of the waste wood flow in Sweden today and the next 25-30 years. The study has confirmed previous studies that waste wood contains a substantial proportion of fine fraction. 25-40% of the waste wood passed a sieve with a mesh size of 4 mm at screening trials. Chemical analyses indicated that the fine fraction will be the main contributor to contaminants of potassium, chlorine, sodium, zinc and lead. Further studies are suggested to focus on sorting, preparation, classification and quality assurance of waste wood.

Energy from wood - an overview

International Nuclear Information System (INIS)

Nussbaumer, T.

2000-01-01

The present publication is the introduction to a series of papers on fundamentals and applications of wood energy. It summarizes figures and data of the actual situation of fuel wood utilization in Switzerland and its potential for the future. Further, the advantages of bio-energy are discussed and the possibilities of funding for bio-energy in Switzerland are described. Wood contributes with 2.5% to the total energy demand in Switzerland nowadays. However, the utilization of wood energy can be more than doubled, which is one of the targets of the Swiss energy policy. The supply chains for the different types of fuel wood are described and specifications and prices of log wood, forestry wood chips and wood residues are presented. The main applications of wood energy are residential heating with manually operated wood boilers and stoves, on the one hand, and heat production with automatic wood furnaces in industry and communities, on the other hand. Automatic furnaces have been promoted in the past ten years and hence they contribute nowadays with more than 50% to the energy supply from wood with a further growing share. As an assistance for further information, a list of institutions and addresses in the field of wood energy in Switzerland is given in the paper. (author)

Dependence of Microcrack Behavior in Wood on Moisture Content during Drying

Directory of Open Access Journals (Sweden)

Hiroyuki Yamamoto

2013-01-01

Full Text Available A modified confocal laser scanning microscopy (CLSM system was developed not only to observe the microcracks on the surface of Cryptomeria japonica D. Don in situ at the cellular level but also to obtain information about the moisture content (MC of the wood surface by measuring the change in its electrical resistivity. The sequential images and changes in the electrical resistivity of the wood surface indicated that microcracks formed between the tracheid and ray parenchyma in the latewood region at >1.0E + 07 Ω/sq (square. Microcracks formed when the MC of the wood surface was below the fiber saturation point determined through regression analysis of the surface electrical resistivity and MC. Most of the microcracks develop when the surface electrical resistivity ranged from 3.95E + 10 to 3.60E + 12 Ω/sq. When the surface MC was ~2.5%, microcracks closed and the surface electrical resistivity was either ~1.00E + 15 Ω/sq or outside the measurement range. The modified CLSM and the method to measure the MC of the wood surface can be used to acquire information about the surface MC in specific areas shown in CLSM images. The findings indicated that the MC of the surface of the wood plays an important role in suppressing the emergence of microcracks in drying wood. The modified CLSM system and the method of measuring the MC of the surface of wood can be used to efficiently evaluate methods of drying wood and the quality of dried wood.

NIR monitoring of in-service wood structures

Science.gov (United States)

Michela Zanetti; Timothy G. Rials; Douglas Rammer

2005-01-01

Near infrared spectroscopy (NIRS) was used to study a set of Southern Yellow Pine boards exposed to natural weathering for different periods of exposure time. This non-destructive spectroscopic technique is a very powerful tool to predict the weathering of wood when used in combination with multivariate analysis (Principal Component Analysis, PCA, and Projection to...

Wood preservative testing

Science.gov (United States)

Rebecca Ibach; Stan T. Lebow

2012-01-01

Most wood species used in commercial and residential construction have little natural biological durability and will suffer from biodeterioration when exposed to moisture. Historically, this problem has been overcome by treating wood for outdoor use with toxic wood preservatives. As societal acceptance of chemical use changes, there is continual pressure to develop and...

Modelling piloted ignition of wood and plastics

International Nuclear Information System (INIS)

Blijderveen, Maarten van; Bramer, Eddy A.; Brem, Gerrit

2012-01-01

Highlights: ► We model piloted ignition times of wood and plastics. ► The model is applied on a packed bed. ► When the air flow is above a critical level, no ignition can take place. - Abstract: To gain insight in the startup of an incinerator, this article deals with piloted ignition. A newly developed model is described to predict the piloted ignition times of wood, PMMA and PVC. The model is based on the lower flammability limit and the adiabatic flame temperature at this limit. The incoming radiative heat flux, sample thickness and moisture content are some of the used variables. Not only the ignition time can be calculated with the model, but also the mass flux and surface temperature at ignition. The ignition times for softwoods and PMMA are mainly under-predicted. For hardwoods and PVC the predicted ignition times agree well with experimental results. Due to a significant scatter in the experimental data the mass flux and surface temperature calculated with the model are hard to validate. The model is applied on the startup of a municipal waste incineration plant. For this process a maximum allowable primary air flow is derived. When the primary air flow is above this maximum air flow, no ignition can be obtained.

Investigation of the Acoustic Properties of Chemically Impregnated Kayu Malam Wood Used for Musical Instrument

Directory of Open Access Journals (Sweden)

Md. Faruk Hossen

2018-01-01

Full Text Available The chemical modification or impregnation through preparing the wood polymer composites (WPCs can effectively reduce the hygroscopicity as well as can improve the acoustic properties of wood. On the other hand, a small amount of nanoclay into the chemical mixture can further improve the different properties of the WPCs through the preparation of wood polymer nanocomposites (WPNCs. Kayu Malam wood species with styrene (St, vinyl acetate (VA, and montmorillonite (MMT nanoclay were used for the preparation of WPNCs. The acoustic properties such as specific dynamic Young’s modulus (Ed/γ, internal friction (Q−1, and acoustic conversion efficiency (ACE of wood were examined using free-free flexural vibration. It was observed that the chemically impregnated wood composite showed a higher value of Ed/γ than raw wood and the nanoclay-loaded wood nanocomposite showed the highest value. The reverse trend was observed in the case of Q−1. On the other hand, chemical impregnation has a minor effect on ACE of wood for musical instruments. The results suggested that the chemically impregnated Kayu Malam wood polymer nanocomposite (WPNC is suitable for making soundboards of violin and guitar instruments to be played longer without losing tone quality.

Wood Dust

Science.gov (United States)

Learn about wood dust, which can raise the risk of cancers of the paranasal sinuses and nasal cavity. High amounts of wood dust are produced in sawmills, and in the furniture-making, cabinet-making, and carpentry industries.

Wood Smoke

Science.gov (United States)

Smoke is made up of a complex mixture of gases and fine, microscopic particles produced when wood and other organic matter burn. The biggest health threat from wood smoke comes from fine particles (also called particulate matter).

Evaluation of kiln-drying schedules for wild cherry wood (Cerasus avium)

OpenAIRE

Korkut, Süleyman; Ünsal, Öner; Kocaefe, Duygu; Aytin, Ayhan; Gökyar, Asli

2013-01-01

Wild cherry wood (Cerasus avium (L.) Monench) lumber with a nominal thickness of 5 cm from Duzce region in Turkey was dried through conventional kiln drying using two different programs which are unprotective drying schedules, and protective drying schedules. The aim was to obtain the most desirable kiln schedule for keeping the wood quality at an appropriate level up to final moisture content of 12±2% was reached. Intensity of warping (twist, bow, cup, crook) occurrence, superficial, interna...

Consequences of bioenergy wood extraction for landscape-level availability of habitat for dead wood-dependent organisms.

Science.gov (United States)

Hiron, Matthew; Jonsell, Mats; Kubart, Ariana; Thor, Göran; Schroeder, Martin; Dahlberg, Anders; Johansson, Victor; Ranius, Thomas

2017-08-01

Stumps and slash resulting from forest clearcutting is used as a source of low-net-carbon energy, but there are concerns about the consequences of biofuel extraction on biodiversity. Logging residues constitute potentially important habitats, since a large part of forest biodiversity is dependent on dead wood. Here we used snapshot field data from a managed forest landscape (25 000 ha) to predict landscape scale population changes of dead wood dependent organisms after extraction of stumps and slash after clearcutting. We did this by estimating habitat availability for all observed dead wood-dependent beetles, macrofungi, and lichens (380 species) in the whole landscape. We found that 53% of species occurred in slash or stumps. For most species, population declines after moderate extraction (≤30%) were small (dead wood types. However, some species were only recorded in slash and stumps. Red listed species were affected by slash and stump extraction (12 species), but less often than other species. Beetles and fungi were more affected by stump extraction, while lichens were more affected by slash extraction. For beetles and lichens, extraction of a combination of spruce, pine and birch resulted in larger negative effects than if only extracting spruce, while for fungi tree species had little effect. We conclude that extensive extraction decreases the amount of habitat to such extent that it may have negative consequences on species persistence at the landscape level. The negative consequences can be limited by extracting only slash, or only logging residues from spruce stands. Copyright © 2017 Elsevier Ltd. All rights reserved.

Mechanical behaviour of wood T-joints. Experimental and numerical investigation

Directory of Open Access Journals (Sweden)

C.L. dos Santos

2015-01-01

Full Text Available Results of a double-shear single-dowel wood connection tested under monotonic quasi-static compression loading are presented and discussed in this paper. The wood used in this study was a pine wood, namely the Pinus pinaster species, which is one of the most important Portuguese species. Each connection (specimen consists of three wood members: a centre member, loaded in compression along the parallel-tograin direction and two simply supported side members, loaded along the perpendicular-to-grain direction (Tconnection. The load transfer between wood members was assured by means of a steel dowel, which is representative of the most common joining technique applied for structural details in wooden structures. The complete load-slip behaviour of the joint is obtained until failure. In particular, the values of the stiffness, the ultimate loads and the ductility were evaluated. Additionally, this investigation proposed non-linear 3D finite element models to simulate the T-joint behaviour. The interaction between the dowel and the wood members was simulated using contact finite elements. A plasticity model, based on Hill’s criterion, was used to simulate the joint ductility and cohesive damage modelling was applied to simulate the brittle failure modes (splitting observed in the side members of the joint. The simulation procedure allowed a satisfactory description of the non-linear behaviour of the T-joint including the collapse prediction.

An expert system for ranking companies and investments: wood industry case

Directory of Open Access Journals (Sweden)

Hliadis Lazaros

2003-01-01

Full Text Available Wood industry is a very important part of both the Greek Rural and industrial sector. The discovery of the differentiation in the level of growth and in the quality of financial management between the Greek wood companies can provide very important aid in the design of an effective rural development policy. The evaluation and ranking of Greek wood companies based on actual financial data is a very complicated task and it requires expertise knowledge and skills. On the other hand a computer expert system can perform validation and evaluation in an efficient way and can substitute human experts. An expert system was designed and developed towards this direction. It uses multicriteria analysis for each one of the wood companies based on actual financial data and it applies fundamental principles of fuzzy logic in order to calculate the expected intervals of flows for the following years. .

Finite element modeling of small-scale tapered wood-laminated composite poles with biomimicry features

Science.gov (United States)

Cheng Piao; Todd F. Shupe; R.C. Tang; Chung Y. Hse

2008-01-01

Tapered composite poles with biomimicry features as in bamboo are a new generation of wood laminated composite poles that may some day be considered as an alternative to solid wood poles that are widely used in the transmission and telecommunication fields. Five finite element models were developed with ANSYS to predict and assess the performance of five types of...

Wood thermoplastic composites

Science.gov (United States)

Daniel F. Caulfield; Craig Clemons; Roger M. Rowell

2010-01-01

The wood industry can expand into new sustainable markets with the formation of a new class of composites with the marriage of the wood industry and the plastics industry. The wood component, usually a flour or fiber, is combined with a thermoplastic to form an extrudable, injectable or thermoformable composite that can be used in many non-structural applications....

How spectroscopy and microspectroscopy of degraded wood contribute to understand fungal wood decay.

Science.gov (United States)

Fackler, Karin; Schwanninger, Manfred

2012-11-01

Nuclear magnetic resonance, mid and near infrared, and ultra violet (UV) spectra of wood contain information on its chemistry and composition. When solid wood samples are analysed, information on the molecular structure of the lignocellulose complex of wood e.g. crystallinity of polysaccharides and the orientation of the polymers in wood cell walls can also be gained. UV and infrared spectroscopy allow also for spatially resolved spectroscopy, and state-of-the-art mapping and imaging systems have been able to provide local information on wood chemistry and structure at the level of wood cells (with IR) or cell wall layers (with UV). During the last decades, these methods have also proven useful to follow alterations of the composition, chemistry and physics of the substrate wood after fungi had grown on it as well as changes of the interactions between the wood polymers within the lignocellulose complex caused by decay fungi. This review provides an overview on how molecular spectroscopic methods could contribute to understand these degradation processes and were able to characterise and localise fungal wood decay in its various stages starting from the incipient and early ones even if the major share of research focussed on advanced decay. Practical issues such as requirements in terms of sample preparation and sample form and present examples of optimised data analysis will also be addressed to be able to detect and characterise the generally highly variable microbial degradation processes within their highly variable substrate wood.

Development and Validation of Marker-Aided Selection Methods for Wood Property Traits in Loblolly Pine and Hybrid Poplar

Energy Technology Data Exchange (ETDEWEB)

Tuskan, G.A.

2001-06-20

Wood properties influence pulp and paper quality. Certainly, overall pulp yields are directly related to the cellulose content, changes in hemicellulose content are associated with changes in pulp cohesiveness, and pulping efficiency is related to lignin content. Despite the importance of wood properties on product quality, little progress has been made in improving such traits because current methods of assessing wood and fiber characteristics are time-consuming, expensive, and often imprecise. Genetic improvement of wood and fiber properties has been further hampered by the large size of trees, delayed reproductive maturity and long harvest cycles. Recent developments in molecular genetics will help overcome the physical, economic and biological constraints in assessing and improving wood properties. Genetic maps consisting of numerous molecular markers are now available for loblolly pine and hybrid poplar. Such markers/maps may be used as part of a marker-aided selection and breeding effort or to expedite the isolation and characterization of genes and/or promoters that directly control wood properties. The objectives of this project are: (1) to apply new and rapid analytical techniques for assessing component wood properties to segregating F2 progeny populations of loblolly pine and hybrid poplar, (2) to map quantitative trait loci and identify molecular markers associated with wood properties in each of the above species and (3) to validate marker-aided selection methods for wood properties in loblolly pine and hybrid poplar.

Online analysis of wood pellets. Quality parameters by near infrared spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Petersen Julius, Lars; Joergensen, Pia [Dong Energy Power, Fredericia (Denmark); Plejdrup Houmoeller, Lars [Arla Foods amba, Global Ingedients R and D, Videbaek (Denmark); Groenkaer Pedersen, Joan [Academy Engineer Chemistry Fertin Pharma, Vejle (Denmark); Anov, Dan

2010-07-01

A near infrared spectroscopy system was installed online in a wood pellet production facility. The objective was to translate real time spectra to useful chemical information, like calorific value, water- and ash content. It was possible to successfully determine water content and calorific value, whereas ash content proved troublesome. (orig.)

Tracheid development and wood quality in larch seedlings under controlled environment

Science.gov (United States)

J.J. Balatinecz; J.L. Farrar

1968-01-01

Several environmental factors necessary for tree growth undergo rhythmic and sometimes abrupt changes during the course of a year, and even during a day. Since wood cells are susceptible to outside influences during their differentiation, certain fluctuations of environmental conditions invariably leave a permanent imprint on xylem anatomy, and hence significantly...

Life cycle environmental impacts of different construction wood waste and wood packaging waste processing methods

OpenAIRE

Manninen, Kaisa; Judl, Jáchym; Myllymaa, Tuuli

2016-01-01

This study compared the life cycle environmental impacts of different wood waste processing methods in three impact categories: climate impact, acidification impacts and eutrophication impacts. The wood waste recovery methods examined were the use of wood waste in terrace boards made out of wood composite which replace impregnated terrace boards, incineration of wood waste in a multi-fuel boiler instead of peat and the use of wood waste in the production of particleboard in either Finland or ...

Mathematical Simulation of Temperature Profiles within Microwave Heated Wood Made for Wood-Based Nano composites

International Nuclear Information System (INIS)

Li, X.; He, X.; Lv, J.; Wu, Y.; Luo, Y.; Chen, H.

2013-01-01

High intensive microwave pretreatment is a new method to modify wood for the fabrication of wood-based nano composites. Based on the physical law on heat transfer, a mathematical model to describe the temperature profiles within wood heated by high intensive microwave was established and simulated in this research. The results showed that the temperature profiles within wood were related to microwave heating methods; The temperature inside wood firstly increased and then gradually decreased along the direction of microwave transmission when the unilateral microwave heating was applied, and the temperature difference along the thickness direction of wood was very significant; The temperature with wood firstly increased and then gradually decreased from the wood surface to interior when the bilateral microwave heating was applied. Compared with the unilateral microwave heating, bilateral microwave heating is a better microwave heating method for the more uniform wood microwave pretreatment.

Volume loss as a tool to assess kiln drying of eucalyptus wood

OpenAIRE

Batista,Djeison Cesar; Klitzke,Ricardo Jorge; Rocha,Márcio Pereira da; Muñiz,Graciela Inez Bolzon de; Batista,Tharcia Ribeiro

2013-01-01

In this study, we aimed to analyze the kiln drying quality of Eucalyptus grandis, Eucalyptus saligna and Eucalyptus dunnii woods with respect to volume loss. Wood from the three species was kiln dried together with the same drying schedule and conditions in a conventional-temperature pilot kiln. Three kinds of volume loss were evaluated: total - from saturated (initial) to machined (final) condition; shrinkage - from saturated to 10% moisture content; and machining - from 10% moisture content...

CONTROL SYSTEM EVALUATION AND IMPLEMENTATION FOR THE ABRASIVE MACHINING PROCESS ON WOOD

OpenAIRE

Stephen Jackson; Richard Lemaster; Daniel E. Saloni

2011-01-01

Continuous process improvement and automation have proven to be powerful tools for the wood processing industries in order to obtain better final product quality and thus increase profits. Abrasive machining represents an important and relevant process in the manufacturing and processing of wood products, which also implies high cost of materials and labor; therefore, special attention to this process is necessary. The objective of this work was to evaluate and demonstrate a process control s...

Evaluating predictive models of software quality

International Nuclear Information System (INIS)

Ciaschini, V; Canaparo, M; Ronchieri, E; Salomoni, D

2014-01-01

Applications from High Energy Physics scientific community are constantly growing and implemented by a large number of developers. This implies a strong churn on the code and an associated risk of faults, which is unavoidable as long as the software undergoes active evolution. However, the necessities of production systems run counter to this. Stability and predictability are of paramount importance; in addition, a short turn-around time for the defect discovery-correction-deployment cycle is required. A way to reconcile these opposite foci is to use a software quality model to obtain an approximation of the risk before releasing a program to only deliver software with a risk lower than an agreed threshold. In this article we evaluated two quality predictive models to identify the operational risk and the quality of some software products. We applied these models to the development history of several EMI packages with intent to discover the risk factor of each product and compare it with its real history. We attempted to determine if the models reasonably maps reality for the applications under evaluation, and finally we concluded suggesting directions for further studies.

Evaluating Predictive Models of Software Quality

Science.gov (United States)

Ciaschini, V.; Canaparo, M.; Ronchieri, E.; Salomoni, D.

2014-06-01

Applications from High Energy Physics scientific community are constantly growing and implemented by a large number of developers. This implies a strong churn on the code and an associated risk of faults, which is unavoidable as long as the software undergoes active evolution. However, the necessities of production systems run counter to this. Stability and predictability are of paramount importance; in addition, a short turn-around time for the defect discovery-correction-deployment cycle is required. A way to reconcile these opposite foci is to use a software quality model to obtain an approximation of the risk before releasing a program to only deliver software with a risk lower than an agreed threshold. In this article we evaluated two quality predictive models to identify the operational risk and the quality of some software products. We applied these models to the development history of several EMI packages with intent to discover the risk factor of each product and compare it with its real history. We attempted to determine if the models reasonably maps reality for the applications under evaluation, and finally we concluded suggesting directions for further studies.

Many Roles of Wood Adhesives

Science.gov (United States)

Charles R. Frihart

2014-01-01

Although wood bonding is one of the oldest applications of adhesives, going back to early recorded history (1), some aspects of wood bonds are still not fully understood. Most books in the general area of adhesives and adhesion do not cover wood bonding. However, a clearer understanding of wood bonding and wood adhesives can lead to improved products. This is important...

Urban Wood Waste Resource Assessment

Energy Technology Data Exchange (ETDEWEB)

Wiltsee, G.

1998-11-20

This study collected and analyzed data on urban wood waste resources in 30 randomly selected metropolitan areas in the United States. Three major categories wood wastes disposed with, or recovered from, the municipal solid waste stream; industrial wood wastes such as wood scraps and sawdust from pallet recycling, woodworking shops, and lumberyards; and wood in construction/demolition and land clearing debris.

Repair and rehabilitation of wood utility poles with fibre-reinforced polymers

Energy Technology Data Exchange (ETDEWEB)

Polyzois, D.; Kell, J.A. [Manitoba Univ., Winnipeg, MB (Canada). Dept. of Civil Engineering

2007-01-15

In order to ensure safe and reliable service, all wood utility poles need an effective maintenance program. The service life of a wood utility pole depends on several factors, such as decay, mechanical damage, weathering, and changing design requirements. An effective preservative treatment and maintenance program can effectively extend the service life of the wood pole. However, all poles will attain a point when they are no longer suitable for their intended use. New innovative methods are therefore required to restore and maintain the structural integrity of existing wood poles, especially in light of the increasing cost of quality wood for use in poles as well as a result of environmental concerns regarding pole disposal and chemical treatment of existing poles. This article presented results from a research program carried out at the University of Manitoba to develop a repair and rehabilitation technique for wood poles using fibre-reinforced polymers (FRP). It also provided a brief overview of current standards for wood utility poles and reinforcing stubs and discussed the experimental program where long, air-dried jack pine poles were tested in order to evaluate the effectiveness of a proposed rehabilitation system consisting of FRP splines and FRP jackets. The ultimate capacity of the poles was determined using the CSA standard for wood poles. The capacity of the rehabilitated poles was nearly 93 per cent of the average ultimate capacity of the average ultimate capacity of poles tested during the first phase of the study, and 23 per cent higher than the capacity required by CSA standards. 7 refs., 2 figs., 4 tabs.

Potential Markets for Wood-Plastic Composites in Japan

Energy Technology Data Exchange (ETDEWEB)

Hirayama, T. [Central Research Laboratory, Showa Denko K.K., Ota-Ku, Tokyo (Japan)

1968-10-15

The marketing possibilities of natural and treated woods are compared. A description is given of the advantages and disadvantages of these materials, together with the effects that improved quality might have on marketing prospects. Extensive reference tables illustrate the change in supply and demand over a number of years. (author)

Biological durability of wood in relation to end-use - Part 1. Towards a European standard for laboratory testing of the biological durability of wood

NARCIS (Netherlands)

Acker, Van J.; Stevens, M.; Carey, J.; Sierra-Alvarez, R.; Militz, H.; Bayon, Le I.; Kleist, G.; Peek, R.D.

2003-01-01

The determination of biological durability of wood is an issue requiring sufficient reliability regarding end-use related prediction of performance. Five test institutes joined efforts to check standard test methods and to improve methodology and data interpretation for assessment of natural

Radioactivity of Wood and Environment

International Nuclear Information System (INIS)

Hus, M.; Kosutic, K.; Lulic, S.

2003-01-01

Nuclear experiments in the atmosphere and nuclear accidents caused global deposition of artificial radionuclides in the soil of Earth's northern hemisphere, the territory of the Republic of Croatia included. Soil contamination by radionuclides resulted in their deposition in plants growing on the contaminated soil as well as in the trees. Large area of the Republic of Croatia is covered with wood, which is exploited in manufacture of industrial wood and for firewood. From approximately 3 million cubic metres of wood exploited annually, nearly one third serves for firewood. In the process of burning a smaller portion of radionuclides deposited in the wood evaporates and goes to atmosphere while a larger portion is retained in the ash. In this paper are presented the results of natural radionuclides 4 0K , 2 32T h and 2 38U as well as of artificial radionuclide 1 37C s content determination in the wood, wood briquette, charcoal and in ash remained after burning the wood, wood briquette and charcoal. The obtained results are discussed from wood radiocontamination aspect and from the aspect of potential environmental radiocontamination by the products from wood burning process. (author)

Impact of fuel quality and burner capacity on the performance of wood pellet stove

Directory of Open Access Journals (Sweden)

Petrović-Bećirović Sanja B.

2015-01-01

Full Text Available Pellet stoves may play an important role in Serbia in the future when fossil fuel fired conventional heating appliances are replaced by more efficient and environmentally friendly devices. Experimental investigation was conducted in order to examine the influence of wood pellet quality, as well as burner capacity (6, 8 and 10 kW, used in the same stove configuration, on the performance of pellet stove with declared nameplate capacity of 8 kW. The results obtained showed that in case of nominal load and combustion of pellets recommended by the stove manufacturer, stove efficiency of 80.03% was achieved. The use of lower quality pellet caused additional 1.13 kW reduction in heat output in case of nominal load and 0.63 kW in case of reduced load. This was attributed to less favourable properties and lower bulk and particle density of lower quality pellet. The use of different burner capacity has shown to have little effect on heat output and efficiency of the stove when pre-set values in the control system of the stove were not altered. It is concluded that replacement of the burner only is not sufficient to increase/decrease the declared capacity of the same stove configuration, meaning that additional measures are necessary. These measures include a new set up of the stove control system, which needs to be properly adjusted for each alteration in stove configuration. Without the adjustment mentioned, declared capacity of the stove cannot be altered, while its CO emission shall be considerably increased.

Wood construction under cold climate

DEFF Research Database (Denmark)

Wang, Xiaodong; Hagman, Olle; Sundqvist, Bror

2014-01-01

As wood constructions increasingly use engineered wood products worldwide, concerns arise about the integrity of the wood and adhesives system. The glueline stability is a crucial issue for engineered wood application, especially under cold climate. In this study, Norway spruce (Picea abies...... affected shear strength of wood joints. As temperature decreased, the shear strength decreased. PUR resin resulted in the strongest shear strength at all temperatures tested. MF resin responded to temperature changes in a similar ways as the PUR resin. The shear strength of wood joints with EPI resins...... specimens need to be tested in further work to more completely present the issue. The EN 301 and EN 302 may need to be specified based on wood species....

Real-Time Mass Spectrometry Monitoring of Oak Wood Toasting: Elucidating Aroma Development Relevant to Oak-aged Wine Quality

Science.gov (United States)

Farrell, Ross R.; Wellinger, Marco; Gloess, Alexia N.; Nichols, David S.; Breadmore, Michael C.; Shellie, Robert A.; Yeretzian, Chahan

2015-11-01

We introduce a real-time method to monitor the evolution of oak aromas during the oak toasting process. French and American oak wood boards were toasted in an oven at three different temperatures, while the process-gas was continuously transferred to the inlet of a proton-transfer-reaction time-of-flight mass spectrometer for online monitoring. Oak wood aroma compounds important for their sensory contribution to oak-aged wine were tentatively identified based on soft ionization and molecular mass. The time-intensity profiles revealed toasting process dynamics illustrating in real-time how different compounds evolve from the oak wood during toasting. Sufficient sensitivity was achieved to observe spikes in volatile concentrations related to cracking phenomena on the oak wood surface. The polysaccharide-derived compounds exhibited similar profiles; whilst for lignin-derived compounds eugenol formation differed from that of vanillin and guaiacol at lower toasting temperatures. Significant generation of oak lactone from precursors was evident at 225 oC. Statistical processing of the real-time aroma data showed similarities and differences between individual oak boards and oak wood sourced from the different origins. This study enriches our understanding of the oak toasting process and demonstrates a new analytical approach for research on wood volatiles.

European wood-fuel trade

International Nuclear Information System (INIS)

Hillring, B.; Vinterbaeck, J.

2001-01-01

This paper discusses research carried out during the l990s on European wood fuel trade at the Department of Forest Management and Products, SLU, in Sweden. Utilisation of wood-fuels and other biofuels increased very rapidly in some regions during that period. Biofuels are replacing fossil fuels which is an effective way to reduce the future influence of green house gases on the climate. The results indicate a rapid increase in wood-fuel trade in Europe from low levels and with a limited number of countries involved. The chief products traded are wood pellets, wood chips and recycled wood. The main trading countries are, for export, Germany and the Baltic states and, for import, Sweden, Denmark and to some extent the Netherlands. In the future, the increased use of biofuel in European countries is expected to intensify activity in this trade. (orig.)

Controversy. The wood war

International Nuclear Information System (INIS)

James, O.

2010-01-01

The author comments the conflict emerging in France between industries exploiting wood for construction and those exploiting it as a heating material for power generation. The first ones accuse the others to steal their raw material, to pull the prices up, and to destabilize the sector. This conflict takes place notably around sawmill wastes which are used either by wood panel fabricators or by wood pellets producers. Both sectors are claiming they are creating more jobs than the other. The French forest indeed offers good opportunities for both sectors, but other countries which are lacking forest surfaces, are buying wood in France. Several issues are matter of discussion: burning wood seems to go against the reduction of greenhouse gas emissions, subsidies awarded to big heater projects. The situation of the wood sector in Austria, Finland and Poland is briefly presented

Aesthetic Qualities of Cross Laminated Timber

DEFF Research Database (Denmark)

Bejder, Anne Kirkegaard

in the great importance wood has had as a building material throughout history as a naturally occurring, strong, light and workable construction material with various multi-sensuous qualities and great applicability. Over the last two decades, wood as a building material has gained renewed focus, partly due......The common thread through this thesis is the aim of bringing the aesthetic, poetic and sensuous qualities of materials into focus. This is done with the belief that materials are more than merely the means of construction, i.e. more than a building system. The thesis takes its point of departure...... is what happens to the aesthetic qualities of wood as a building material in this process? What does it mean to the experience and perception of CLT that it is processed to products whose properties differ significantly from those of wood in its raw form? Based on the hypothesis that CLT possesses...

Challenges in assessing air pollution from residential wood combustion

DEFF Research Database (Denmark)

Olesen, Helge Rørdam

2016-01-01

The paper highlights a number of important challenges in quantifying the impact of residential wood combustion on air quality. The fact that real life emissions are controlled by the behaviour of the users makes it a challenge to determine representative emission factors. Further, in respect...

Growth and wood properties of genetically improved loblolly pine: propagation type comparison and genetic parameters

Science.gov (United States)

Finto Antony; Laurence Schimleck; Lewis Jordan; Benjamin Hornsby; Joseph Dahlen; Richard Daniels; Alexander Clark; Luis Apiolaza; Dudley Huber

2013-01-01

The use of clonal varieties in forestry offers great potential to improve growth traits (quantity) and wood properties (quality) of loblolly pine (Pinus taeda L.). Loblolly pine trees established via somatic embryogenesis (clones), full-sib zygotic crosses, and half-sib zygotic open-pollinated families were sampled to identify variation in growth and wood properties...

Improved prediction of hardwood tree biomass derived from wood density estimates and form factors for whole trees

Science.gov (United States)

David W. MacFarlane; Neil R. Ver Planck

2012-01-01

Data from hardwood trees in Michigan were analyzed to investigate how differences in whole-tree form and wood density between trees of different stem diameter relate to residual error in standard-type biomass equations. The results suggested that whole-tree wood density, measured at breast height, explained a significant proportion of residual error in standard-type...

IMPACT OF ECONOMIC CRISIS ON WOOD MARKETS (CONSUMPTION, PRODUCTION AND TRADE

Directory of Open Access Journals (Sweden)

Maria‐Loredana POPESCU

2013-12-01

Full Text Available Global economic crisis represents one of the causes why wood consumption is increasing especially in countries less developed. In countries where governments couldn’t improve the quality of life and unemployment rate is higher, local communities devastate a lot of forestry. In last thirty years we saw a deforestation process at the global level related to land being converted to other uses: agriculture and urbanization, which represent a positive trend of a negative use. The statistics reveal, on one hand, an increasing demand for paper, paper products, wood products and wood energy. So this point is important to analyze: where wood came from and where it is going as either raw material or processed goods? For undeveloped countries, like Romania, it is easy to export primary wood product without evaluating the consequences. On the other hand, developed countries like Sweden export value added products which brig them higher value and profits and require greater manufacturing and marketing skills (case IKEA. For this, government policy could introduce trade barriers to decrease log consumption (like export taxes and simultaneously support furniture production and trade (e.g. export.

Seminal Quality Prediction Using Clustering-Based Decision Forests

Directory of Open Access Journals (Sweden)

Hong Wang

2014-08-01

Full Text Available Prediction of seminal quality with statistical learning tools is an emerging methodology in decision support systems in biomedical engineering and is very useful in early diagnosis of seminal patients and selection of semen donors candidates. However, as is common in medical diagnosis, seminal quality prediction faces the class imbalance problem. In this paper, we propose a novel supervised ensemble learning approach, namely Clustering-Based Decision Forests, to tackle unbalanced class learning problem in seminal quality prediction. Experiment results on real fertility diagnosis dataset have shown that Clustering-Based Decision Forests outperforms decision tree, Support Vector Machines, random forests, multilayer perceptron neural networks and logistic regression by a noticeable margin. Clustering-Based Decision Forests can also be used to evaluate variables’ importance and the top five important factors that may affect semen concentration obtained in this study are age, serious trauma, sitting time, the season when the semen sample is produced, and high fevers in the last year. The findings could be helpful in explaining seminal concentration problems in infertile males or pre-screening semen donor candidates.

Factors driving and restraining adoption of Automation technologies in Swedish wood product industry.

OpenAIRE

Mapulanga, Mwanza; Saladi, Praveen

2016-01-01

Swedish wood product industry contributes significantly to the economy of the country. This industry adds more value to the sawn timber produced in order to manufacture different wooden products. Companies in Swedish wood product industry are presently seen as underdeveloped in terms of investments and developments in automation technologies. Automation technologies are seen by companies as a solution for improving productivity, product quality, manufacturing cost reduction and ultimately imp...

Manufacture of wood-pellets doubles. Biowatti Oy started a wood pellet plant in Turenki

International Nuclear Information System (INIS)

Rantanen, M.

1999-01-01

Wood pellets have many advantages compared to other fuels. It is longest processed biofuel with favorable energy content. It is simple to use, transport and store. Heating with wood pellets is cheaper than with light fuel oil, and approximately as cheap as utilization of heavy fuel oil, about 110 FIM/MWh. The taxable price of wood pellets is about 550 FIM/t. Stokers and American iron stoves are equally suitable for combustion of wood pellets. Chip fueled stokers are preferred in Finland, but they are also suitable for the combustion of wood pellets. Wood pellets is an environmentally friendly product, because it does not increase the CO 2 load in the atmosphere, and its sulfur and soot emissions are relatively small. The wood pelletizing plant of Biowatti Oy in Turenki was started in an old sugar mill. The Turenki sugar mill was chosen because the technology of the closed sugar factory was suitable for production of wood pellets nearly as such, and required only by slight modifications. A press, designed for briquetting of sugar beat clippings makes the pellets. The Turenki mill will double the volume of wood pellet manufacture in Finland during the next few years. At the start the annual wood pellet production will be 20 000 tons, but the environmental permit allows the production to be increased to 70 000 tons. At first the mill uses planing machine chips as a raw material in the production. It is the most suitable raw material, because it is already dry (moisture content 8-10%), and all it needs is milling and pelletizing. Another possible raw material is sawdust, which moisture content is higher than with planing machine chips. Most of the wood pellets produced are exported e.g. to Sweden, Denmark and Middle Europe. In Sweden there are over 10 000 single-family houses using wood pellets. Biowatti's largest customer is a power plant located in Stockholm, which combusts annually about 200 000 tons of wood pellets

Dr. Byron McKeeby's contribution to Grant Wood's "American Gothic".

Science.gov (United States)

Christen, Arden G; Christen, Joan A

2004-07-01

Grant Wood (1891-1942) was a major American regionalist artist from Iowa who produced his world famous icon, American Gothic in 1930. Along with Mona Lisa and Whistler's Mother, this work has become one of the most recognized paintings in the world. While it has been greatly admired by most of its viewers, it has been criticized by others. Currently on display at the Art Institute of Chicago, this oil painting portrays a grim faced farmer and his somber daughter who are resolutely standing in front of their rural, Gothic Revival farmhouse. The tall, gaunt farmer, looking straight ahead, firmly holds a pitchfork whose tines point upward, while his daughter, with her eyes averted appears to be showing disapproval. In American art, it is unusual to find the hard, cold realism and honest, direct and earthy qualities that Wood captures in American Gothic. Wood's actual intention was to present the work as a subtle and witty commentary on midwestern, rural life. To achieve his goal, Wood emulated the meticulous style and technique of the 16th century Flemish masters. His sister, Nan Wood Graham (1900-1990), and his 62-year-old dentist, Dr. Byron H. McKeeby (1867-1950), posed for the painting. This article describes how Grant developed this artistic style which is reflected in American Gothic. Additionally, it examines the strained interactions between Grant Wood, the artist, and Dr. Byron McKeeby, the model.

Development and Validation of Marker-Aided Selection Methods for Wood Property Traits in Loblolly Pine and Hybrid Poplar; FINAL

International Nuclear Information System (INIS)

Tuskan, G.A.

2001-01-01

Wood properties influence pulp and paper quality. Certainly, overall pulp yields are directly related to the cellulose content, changes in hemicellulose content are associated with changes in pulp cohesiveness, and pulping efficiency is related to lignin content. Despite the importance of wood properties on product quality, little progress has been made in improving such traits because current methods of assessing wood and fiber characteristics are time-consuming, expensive, and often imprecise. Genetic improvement of wood and fiber properties has been further hampered by the large size of trees, delayed reproductive maturity and long harvest cycles. Recent developments in molecular genetics will help overcome the physical, economic and biological constraints in assessing and improving wood properties. Genetic maps consisting of numerous molecular markers are now available for loblolly pine and hybrid poplar. Such markers/maps may be used as part of a marker-aided selection and breeding effort or to expedite the isolation and characterization of genes and/or promoters that directly control wood properties. The objectives of this project are: (1) to apply new and rapid analytical techniques for assessing component wood properties to segregating F(sub 2) progeny populations of loblolly pine and hybrid poplar, (2) to map quantitative trait loci and identify molecular markers associated with wood properties in each of the above species and (3) to validate marker-aided selection methods for wood properties in loblolly pine and hybrid poplar

Reliable and non-destructive positioning of larvae of wood-destroying beetles in wood

International Nuclear Information System (INIS)

Kerner, G.; Thiele, H.; Unger, W.

1980-01-01

Living larvae of wood-destroying insects (house longhorn beetle, deathwatch) can be determined in wood by both X-ray technique and vibration measurements. For such examinations convenient commercial devices were used and tested under laboratory conditions. The methods complement each other and lead to a rationalization of the tests of wood preservatives against wood-destroying insects. It seems to be promising to apply the test methods also to timber already used for building

Effect of lime and wood ash on the nixtamalization of maize and tortilla chemical and nutritional characteristics.

Science.gov (United States)

Pappa, María Renée; de Palomo, Patricia Palacios; Bressani, Ricardo

2010-06-01

The objective of the study was to obtain information on the chemical composition, functional properties, sensory quality and protein value of tortillas made from the nixtamalization of maize using either lime or wood ashes. The Ca, K, Mg, Fe, and Zn content of lime and wood ashes showed lime to be high in Ca content while wood ash contained more K and about 71% of the Ca content of lime. Both contained relatively high levels of Mg, Fe and Zn, but more so in the wood ashes. The level of reagent for nixtamalization was set at 0.8% of the maize weight. All other processing conditions were kept constant. The pH of the cooking solution was 12.0 for lime and 10.9 for wood ash. The moisture content of maize at 60 min of cooking was 45.8% for both treatments, however after 12 h of soaking, moisture level was 51.0% for the lime treatment and only 46.8% for the ash treatment. Solids (2.4%) in the lime cooking liquor were higher than in the wood ash liquor (1.0%). Chemical composition changes were similar between treatments in masa and tortilla; however, both masa and tortillas absorbed relatively high levels of all minerals including Fe and Zn from the wood ash treatment. The different treatment influenced functional properties particularly hardness and color. Tortilla characteristics were also similar. Protein quality of both alkali cooked products was lower than that of raw corn, more so the product from the wood ash treatment. Although some differences were observed in the sensory studies, human subjects did not dislike the wood ash made tortillas.

Justification of the Production Process of Pressed Wood and Study of its Properties

Science.gov (United States)

Polilov, A. N.; Dornyak, O. R.; Shamaev, V. A.; Rumachik, M. M.

2018-05-01

Results of a numerical analysis of the stress-strain state of wood during its pressing in different symmetry directions of the anisotropic material are presented. It is shown that the anisotropy of mechanical properties of wood is an important factor determining both the structural characteristics of the porous system and its strength. A mathematical modeling of the process of pressing wood as a three-phase anisotropic rheologically complex capillary-porous system allows one to predict parameters of the resulting wood composite. The compressed wood obtained by the production modes developed has a tensile strength eight times greater than that of the natural one, which is comparable to the strength of the St3 steel, but its specific strength is higher than that of the St45 steel. Compression and impregnation of softwood species with an aqueous solution of carbamide allows one to harden them. This kind of treatment endows the wood with enhanced strength characteristics comparable to the characteristics of the St3 steel. The special features of tensile tests used to estimate the elastic modulus and strength characteristics of such materials are considered. Data obtained by different testing methods are correlated, and characteristics of the strengthened wood and some brends of steel are compared.

A simple metric to predict stream water quality from storm runoff in an urban watershed.

Science.gov (United States)

Easton, Zachary M; Sullivan, Patrick J; Walter, M Todd; Fuka, Daniel R; Petrovic, A Martin; Steenhuis, Tammo S

2010-01-01

The contribution of runoff from various land uses to stream channels in a watershed is often speculated and used to underpin many model predictions. However, these contributions, often based on little or no measurements in the watershed, fail to appropriately consider the influence of the hydrologic location of a particular landscape unit in relation to the stream network. A simple model was developed to predict storm runoff and the phosphorus (P) status of a perennial stream in an urban watershed in New York State using the covariance structure of runoff from different landscape units in the watershed to predict runoff in time. One hundred and twenty-seven storm events were divided into parameterization (n = 85) and forecasting (n = 42) data sets. Runoff, dissolved P (DP), and total P (TP) were measured at nine sites distributed among three land uses (high maintenance, unmaintained, wooded), three positions in the watershed (near the outlet, midwatershed, upper watershed), and in the stream at the watershed outlet. The autocorrelation among runoff and P concentrations from the watershed landscape units (n = 9) and the covariance between measurements from the landscape units and measurements from the stream were calculated and used to predict the stream response. Models, validated using leave-one-out cross-validation and a forecasting method, were able to correctly capture temporal trends in streamflow and stream P chemistry (Nash-Sutcliffe efficiencies, 0.49-0.88). The analysis suggests that the covariance structure was consistent for all models, indicating that the physical processes governing runoff and P loss from these landscape units were stationary in time and that landscapes located in hydraulically active areas have a direct hydraulic link to the stream. This methodology provides insight into the impact of various urban landscape units on stream water quantity and quality.

Integrated production method for wood fuel and pulp wood in Northern Finland; Polttojakeen hankinta puun yhdistelmaekorjuussa ja integroitu energiapuun tuotantomenetelmae Pohjois-Suomessa

Energy Technology Data Exchange (ETDEWEB)

Hooli, A [Hooli Oy, Kemi (Finland); Kuitto, P J [VTT Energy, Jyvaeskylae (Finland); Ranta, T [Finntech Ltd. Oy, Jyvaeskylae (Finland)

1997-12-31

Chip production company Hooli Ltd. has built an innovative mobile chain-flail delimbing-debarking-unit which includes also a hammer crusher for wood fuel. This integrated production method for wood fuel and pulp wood based on that unit has been planned especially for the circumstances where the power or heating plants are near and the pulp mills more remote from the wood processing sites. The trees are felt into bunches and transported as whole trees or tree-sections to the roadside. The Hooli-unit delimbs and debarks the trees using multi-tree processing. The optimal bark content of Scot pine bolts after processing is under 1 %. All green branches, stops and bark are directly crushed into wood fuel in the same unit. Fuel chips are carried to the nearest power plant. The debarked bolts are transported to the pulpmills in the form of roundwood or pulpchips, thus giving better economy for the whole method. Based on first field experiments in 1995 this method has operated well. However, there are still development work ahead: e.g. good debarking quality of birch and spruce in the winter conditions. To attain the targets of the project looks promising. The project is carried out as joint project between Hooli Ltd, Finntech Ltd. Oy, the Finnish Forest Research Institute, Veitsiluoto Ltd and VTT Energy. The chain-flail delimbing-debarking-crushing unit was built at Tervolan Konepaja Ky

Integrated production method for wood fuel and pulp wood in Northern Finland; Polttojakeen hankinta puun yhdistelmaekorjuussa ja integroitu energiapuun tuotantomenetelmae Pohjois-Suomessa

Energy Technology Data Exchange (ETDEWEB)

Hooli, A. [Hooli Oy, Kemi (Finland); Kuitto, P.J. [VTT Energy, Jyvaeskylae (Finland); Ranta, T. [Finntech Ltd. Oy, Jyvaeskylae (Finland)

1996-12-31

Chip production company Hooli Ltd. has built an innovative mobile chain-flail delimbing-debarking-unit which includes also a hammer crusher for wood fuel. This integrated production method for wood fuel and pulp wood based on that unit has been planned especially for the circumstances where the power or heating plants are near and the pulp mills more remote from the wood processing sites. The trees are felt into bunches and transported as whole trees or tree-sections to the roadside. The Hooli-unit delimbs and debarks the trees using multi-tree processing. The optimal bark content of Scot pine bolts after processing is under 1 %. All green branches, stops and bark are directly crushed into wood fuel in the same unit. Fuel chips are carried to the nearest power plant. The debarked bolts are transported to the pulpmills in the form of roundwood or pulpchips, thus giving better economy for the whole method. Based on first field experiments in 1995 this method has operated well. However, there are still development work ahead: e.g. good debarking quality of birch and spruce in the winter conditions. To attain the targets of the project looks promising. The project is carried out as joint project between Hooli Ltd, Finntech Ltd. Oy, the Finnish Forest Research Institute, Veitsiluoto Ltd and VTT Energy. The chain-flail delimbing-debarking-crushing unit was built at Tervolan Konepaja Ky

Wood anatomy and physical and chemical properties of fast growing Athel tamarisk (Tamarix aphylla L.

Directory of Open Access Journals (Sweden)

Reza oladi

2017-02-01

Full Text Available Athel tamarisk (Tamarix aphylla is a fast growing, evergreen tree succeeding in the most soils and can tolerate the saline conditions. Despite its ecological importance and wide distribution in central and southern parts of Iran, wood properties of this species has little been concerned. However, the potential of this species in cellulosic industries of Middle East dry countries has recently been focused. Hence, to study wood anatomy and physical and chemical properties of Athel tamarisk, 3 stands were selected and felled from the Zabol region (Sistan and Baluchestan province. Wood anatomical features of this species were studied and listed according to the list of microscopic features for hardwood identification by IAWA Committee. In addition, lignin distribution in xylem was studied using fluorescence microscopy. Calculating fiber biometry features assessed that although fiber quality is not perfect but meets the standards of paper production, comparing other commercially used hardwoods in this industry. According to chemical composition analysis, cellulose content of this wood is rather low (39% which could be a result of large amount of thin-walled paranchyma cells in xylem. Lignin content is a bit higher than average hardwoods and this component is concentrated in vessels and fibers. Physical properties of studied wood samples (specific gravity and shrinkage values were in the range of other light-weight and fast growing hardwoods and thus this wood is expected to have similar end-use quality.

Request for wood samples

NARCIS (Netherlands)

NN,

1977-01-01

In recent years the wood collection at the Rijksherbarium was greatly expanded following a renewed interest in wood anatomy as an aid for solving classification problems. Staff members of the Rijksherbarium added to the collection by taking interesting wood samples with them from their expeditions

THE MEASUREMENT AND DISTRIBUTION OF WOOD DUST

Directory of Open Access Journals (Sweden)

Andrea Rosario Proto

2010-03-01

Full Text Available In Italy, the woodworking industry presents many issues in terms of occupational health and safety. This study on exposure to wood dust could contribute to the realization of a prevention model in order to limit exposure to carcinogenic agents to the worker. The sampling methodology illustrated the analysis of dust emissions from the woodworking machinery in operation throughout the various processing cycles. The quantitative and qualitative assessment of exposure was performed using two different methodologies. The levels of wood dust were determined according to EN indications and sampling was conducted using IOM and Cyclon personal samplers. The qualitative research of wood dust was performed using an advanced laser air particle counter. This allowed the number of particles present to be counted in real time. The results obtained allowed for an accurate assessment of the quality of the dust emitted inside the workplace during the various processing phases. The study highlighted the distribution of air particles within the different size classes, the exact number of both thin and ultra-thin dusts, and confirmed the high concentration of thin dust particles which can be very harmful to humans.

Predicting personal preferences in subjective video quality assessment

DEFF Research Database (Denmark)

Korhonen, Jari

2017-01-01

In this paper, we study the problem of predicting the visual quality of a specific test sample (e.g. a video clip) experienced by a specific user, based on the ratings by other users for the same sample and the same user for other samples. A simple linear model and algorithm is presented, where...... the characteristics of each test sample are represented by a set of parameters, and the individual preferences are represented by weights for the parameters. According to the validation experiment performed on public visual quality databases annotated with raw individual scores, the proposed model can predict...

Wood Modification at High Temperature and Pressurized Steam: a Relational Model of Mechanical Properties Based on a Neural Network

Directory of Open Access Journals (Sweden)

Hong Yang

2015-07-01

Full Text Available Thermally modified wood has high dimensional stability and biological durability.But if the process parameters of thermal modification are not appropriate, then there will be a decline in the physical properties of wood.A neural network algorithm was employed in this study to establish the relationship between the process parameters of high-temperature and high-pressure thermal modification and the mechanical properties of the wood. Three important parameters: temperature, relative humidity, and treatment time, were considered as the inputs to the neural network. Back propagation (BP neural network and radial basis function (RBF neural network models for prediction were built and compared. The comparison showed that the RBF neural network model had advantages in network structure, convergence speed, and generalization capacity. On this basis, the inverse model, reflecting the relationship between the process parameters and the mechanical properties of wood, was established. Given the desired mechanical properties of the wood, the thermal modification process parameters could be inversely optimized and predicted. The results indicated that the model has good learning ability and generalization capacity. This is of great importance for the theoretical and applicational studies of the thermal modification of wood.

Building solar dryer of tropical woods; Construccion de un secador solar de maderas tropicales

Energy Technology Data Exchange (ETDEWEB)

Hernandez R, J; Flores M, F. E; Cuevas D, O [Universidad de Quintana Roo, Chetumal, Quintana Roo (Mexico); Tolentino E, G [LABINTHAP-SEPI-ESIME-IPN, Mexico, D.F. (Mexico)

2000-07-01

In Quintana Roo, Mexico, several species of wood are used for handicrafts. The most commonly method used in the communities nearby Chetumal is natural drying, with the disadvantage of low quality in their products because the moisture contains in the wood. In this project studied the design of solar dryer for tropical woods in Quintana Roo. [Spanish] En este trabajo, se parte del analisis de las condiciones climatologicas existentes en el estado de Quintana Roo, Mexico, asi como de las necesidades de madera seca de una comunidad, como parametros basicos para el diseno y construccion de un secador solar de maderas tropicales.

Wood fuel and the environment

International Nuclear Information System (INIS)

Foster, C.A.

1992-01-01

The purpose of this paper is to try and demonstrate the role that the use of Wood as a Fuel can play in our environment. The term ''Wood Fuel'', for the purposes of these proceedings, refers to the use of wood obtained from the forest or the farm. It does not refer to waste wood from for example buildings. The role of wood fuel in the environment can be assessed at many different levels. In this paper three different scales of ''Environment'' and the role of wood fuel in each, will be considered. These three scales are namely the global environment, the local environment, and the National (community) environment. (Author)

Sleep Quality Prediction From Wearable Data Using Deep Learning.

Science.gov (United States)

Sathyanarayana, Aarti; Joty, Shafiq; Fernandez-Luque, Luis; Ofli, Ferda; Srivastava, Jaideep; Elmagarmid, Ahmed; Arora, Teresa; Taheri, Shahrad

2016-11-04

The importance of sleep is paramount to health. Insufficient sleep can reduce physical, emotional, and mental well-being and can lead to a multitude of health complications among people with chronic conditions. Physical activity and sleep are highly interrelated health behaviors. Our physical activity during the day (ie, awake time) influences our quality of sleep, and vice versa. The current popularity of wearables for tracking physical activity and sleep, including actigraphy devices, can foster the development of new advanced data analytics. This can help to develop new electronic health (eHealth) applications and provide more insights into sleep science. The objective of this study was to evaluate the feasibility of predicting sleep quality (ie, poor or adequate sleep efficiency) given the physical activity wearable data during awake time. In this study, we focused on predicting good or poor sleep efficiency as an indicator of sleep quality. Actigraphy sensors are wearable medical devices used to study sleep and physical activity patterns. The dataset used in our experiments contained the complete actigraphy data from a subset of 92 adolescents over 1 full week. Physical activity data during awake time was used to create predictive models for sleep quality, in particular, poor or good sleep efficiency. The physical activity data from sleep time was used for the evaluation. We compared the predictive performance of traditional logistic regression with more advanced deep learning methods: multilayer perceptron (MLP), convolutional neural network (CNN), simple Elman-type recurrent neural network (RNN), long short-term memory (LSTM-RNN), and a time-batched version of LSTM-RNN (TB-LSTM). Deep learning models were able to predict the quality of sleep (ie, poor or good sleep efficiency) based on wearable data from awake periods. More specifically, the deep learning methods performed better than traditional logistic regression. “CNN had the highest specificity and

A Neural Network Model for Prediction of Sound Quality

DEFF Research Database (Denmark)

Nielsen,, Lars Bramsløw

An artificial neural network structure has been specified, implemented and optimized for the purpose of predicting the perceived sound quality for normal-hearing and hearing-impaired subjects. The network was implemented by means of commercially available software and optimized to predict results...... obtained in subjective sound quality rating experiments based on input data from an auditory model. Various types of input data and data representations from the auditory model were used as input data for the chosen network structure, which was a three-layer perceptron. This network was trained by means...... the physical signal parameters and the subjectively perceived sound quality. No simple objective-subjective relationship was evident from this analysis....

Online sorting of recovered wood waste by automated XRF-technology: part II. Sorting efficiencies.

Science.gov (United States)

Hasan, A Rasem; Solo-Gabriele, Helena; Townsend, Timothy

2011-04-01

Sorting of waste wood is an important process practiced at recycling facilities in order to detect and divert contaminants from recycled wood products. Contaminants of concern include arsenic, chromium and copper found in chemically preserved wood. The objective of this research was to evaluate the sorting efficiencies of both treated and untreated parts of the wood waste stream, and metal (As, Cr and Cu) mass recoveries by the use of automated X-ray fluorescence (XRF) systems. A full-scale system was used for experimentation. This unit consisted of an XRF-detection chamber mounted on the top of a conveyor and a pneumatic slide-way diverter which sorted wood into presumed treated and presumed untreated piles. A randomized block design was used to evaluate the operational conveyance parameters of the system, including wood feed rate and conveyor belt speed. Results indicated that online sorting efficiencies of waste wood by XRF technology were high based on number and weight of pieces (70-87% and 75-92% for treated wood and 66-97% and 68-96% for untreated wood, respectively). These sorting efficiencies achieved mass recovery for metals of 81-99% for As, 75-95% for Cu and 82-99% of Cr. The incorrect sorting of wood was attributed almost equally to deficiencies in the detection and conveyance/diversion systems. Even with its deficiencies, the system was capable of producing a recyclable portion that met residential soil quality levels established for Florida, for an infeed that contained 5% of treated wood. Copyright © 2010 Elsevier Ltd. All rights reserved.

Wood-plastic combination

International Nuclear Information System (INIS)

Schaudy, R.

1978-02-01

A review on wood-plastic combinations is given including the production (wood and plastic component, radiation hardening, curing), the obtained properties, present applications and prospects for the future of these materials. (author)

A Case of Quality Prediction of Architecture Knowledge Sharing through Model Mapping

NARCIS (Netherlands)

Liang, Peng; Jansen, Anton; Avgeriou, Paris

2008-01-01

In this report, we introduce the AK sharing activity with a query-based scenario, and the motivation for the prediction of AK sharing quality prediction. In the end, a concrete case of quality prediction of AK sharing through model mapping was presented with assumptions.

Economy of wood supply

International Nuclear Information System (INIS)

Imponen, V.

1993-01-01

Research and development of wood fuels production was vigorous in the beginning of the 1980's. Techniques and working methods used in combined harvesting and transportation of energy and merchantable wood were developed in addition to separate energy wood delivery. After a ten year silent period the research on this field was started again. At present the underutilization of forest supplies and the environmental effects of energy production based on fossil fuels caused the rebeginning of the research. One alternative for reduction of the price of wood fuels at the utilization site is the integration of energy and merchantable wood deliveries together. Hence the harvesting and transportation devices can be operated effectively, and the organizational costs are decreased as well. The wood delivery costs consist of the stumpage price, the harvesting and transportation costs, and of general expenses. The stumpage price form the largest cost category (over 50 %) of the industrial merchantable wood delivery, and the harvesting and transportation costs in the case of thinningwood delivery. Forest transportation is the largest part of the delivery costs of logging residues. The general expenses, consisting of the management costs and the interest costs of the capital bound to the storages, form a remarkable cost category in delivery of low-rank wood for energy or conversion purposes. The costs caused by the harvesting of thinningwood, the logging residues, chipping and crushing, the lorry transportation are reviewed in this presentation

Wood's lamp examination

Science.gov (United States)

... this page: //medlineplus.gov/ency/article/003386.htm Wood lamp examination To use the sharing features on this page, please enable JavaScript. A Wood lamp examination is a test that uses ultraviolet ( ...

Wood preservation

Science.gov (United States)

Rebecca E. Ibach

1999-01-01

When left untreated in many outdoor applications, wood becomes subject to degradation by a variety of natural causes. Although some trees possess naturally occurring resistance to decay (Ch. 3, Decay Resistance), many are in short supply or are not grown in ready proximity to markets. Because most commonly used wood species, such as Southern Pine, ponderosa pine, and...

Smoke emissions in small-scale burning of wood

International Nuclear Information System (INIS)

Tuomi, S.

1993-01-01

The article is based on research carried out in Finland and Sweden on the subject of emissions of smoke in the small-scale burning of wood and the factors affecting it. Due to incomplete combustion, small-scale burning of wood is particularly typified by its emissions of solid particles, carbon monoxide, hydrocarbons and PAH compounds. Included among factors influencing the volume of emissions are the load imposed on the heating device, the manner in which the fuel is fed into the firebox, fuel quality, and heating device structure. Emissions have been found to be at their minimum in connection with heating systems based on accumulators. Emissions can be significantly reduced by employing state-of-the-art technology, appropriate ways of heating and by dry fuel. A six-year bioenergy research programme was launched early in 1993 in Finland. All leading research institutions and enterprises participate in this programme. Reduction of emissions has been set as the central goal in the part dealing with small-scale burning of wood. Application of catalytic combustion in Finnish-made heating devices is one of the programmes development targets. Up to this date, the emissions produced in the small-scale burning of wood are not mentioned in official regulations pertaining to approved heating devices. In Sweden tar emissions are applied as a measure of the environmental impact imposed by heating devices

Data Quality Enhanced Prediction Model for Massive Plant Data

International Nuclear Information System (INIS)

Park, Moon-Ghu; Kang, Seong-Ki; Shin, Hajin

2016-01-01

This paper introduces an integrated signal preconditioning and model prediction mainly by kernel functions. The performance and benefits of the methods are demonstrated by a case study with measurement data from a power plant and its components transient data. The developed methods will be applied as a part of monitoring massive or big data platform where human experts cannot detect the fault behaviors due to too large size of the measurements. Recent extensive efforts for on-line monitoring implementation insists that a big surprise in the modeling for predicting process variables was the extent of data quality problems in measurement data especially for data-driven modeling. Bad data for training will be learned as normal and can make significant degrade in prediction performance. For this reason, the quantity and quality of measurement data in modeling phase need special care. Bad quality data must be removed from training sets to the bad data considered as normal system behavior. This paper presented an integrated structure of supervisory system for monitoring the plants or sensors performance. The quality of the data-driven model is improved with a bilateral kernel filter for preprocessing of the noisy data. The prediction module is also based on kernel regression having the same basis with noise filter. The model structure is optimized by a grouping process with nonlinear Hoeffding correlation function

Data Quality Enhanced Prediction Model for Massive Plant Data

Energy Technology Data Exchange (ETDEWEB)

Park, Moon-Ghu [Nuclear Engr. Sejong Univ., Seoul (Korea, Republic of); Kang, Seong-Ki [Monitoring and Diagnosis, Suwon (Korea, Republic of); Shin, Hajin [Saint Paul Preparatory Seoul, Seoul (Korea, Republic of)

2016-10-15

This paper introduces an integrated signal preconditioning and model prediction mainly by kernel functions. The performance and benefits of the methods are demonstrated by a case study with measurement data from a power plant and its components transient data. The developed methods will be applied as a part of monitoring massive or big data platform where human experts cannot detect the fault behaviors due to too large size of the measurements. Recent extensive efforts for on-line monitoring implementation insists that a big surprise in the modeling for predicting process variables was the extent of data quality problems in measurement data especially for data-driven modeling. Bad data for training will be learned as normal and can make significant degrade in prediction performance. For this reason, the quantity and quality of measurement data in modeling phase need special care. Bad quality data must be removed from training sets to the bad data considered as normal system behavior. This paper presented an integrated structure of supervisory system for monitoring the plants or sensors performance. The quality of the data-driven model is improved with a bilateral kernel filter for preprocessing of the noisy data. The prediction module is also based on kernel regression having the same basis with noise filter. The model structure is optimized by a grouping process with nonlinear Hoeffding correlation function.

The use of new, aqueous chemical wood modifications to improve the durability of wood-plastic composites

Science.gov (United States)

Rebecca E. Ibach; Craig M. Clemons; George C. Chen

2017-01-01

The wood flour used in wood-plastic composites (WPCs) can biologically deteriorate and thus the overall mechanical performance of WPCs decrease when exposed to moisture and fungal decay. Protecting the wood flour by chemical modification can improve the durability of the wood in a nontoxic way so it is not harmful to the environment. WPCs were made with modified wood...

NOAA's National Air Quality Predictions and Development of Aerosol and Atmospheric Composition Prediction Components for the Next Generation Global Prediction System

Science.gov (United States)

Stajner, I.; Hou, Y. T.; McQueen, J.; Lee, P.; Stein, A. F.; Tong, D.; Pan, L.; Huang, J.; Huang, H. C.; Upadhayay, S.

2016-12-01

NOAA provides operational air quality predictions using the National Air Quality Forecast Capability (NAQFC): ozone and wildfire smoke for the United States and airborne dust for the contiguous 48 states at http://airquality.weather.gov. NOAA's predictions of fine particulate matter (PM2.5) became publicly available in February 2016. Ozone and PM2.5 predictions are produced using a system that operationally links the Community Multiscale Air Quality (CMAQ) model with meteorological inputs from the North American mesoscale forecast Model (NAM). Smoke and dust predictions are provided using the Hybrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT) model. Current NAQFC focus is on updating CMAQ to version 5.0.2, improving PM2.5 predictions, and updating emissions estimates, especially for NOx using recently observed trends. Wildfire smoke emissions from a newer version of the USFS BlueSky system are being included in a new configuration of the NAQFC NAM-CMAQ system, which is re-run for the previous 24 hours when the wildfires were observed from satellites, to better represent wildfire emissions prior to initiating predictions for the next 48 hours. In addition, NOAA is developing the Next Generation Global Prediction System (NGGPS) to represent the earth system for extended weather prediction. NGGPS will include a representation of atmospheric dynamics, physics, aerosols and atmospheric composition as well as coupling with ocean, wave, ice and land components. NGGPS is being developed with a broad community involvement, including community developed components and academic research to develop and test potential improvements for potentially inclusion in NGGPS. Several investigators at NOAA's research laboratories and in academia are working to improve the aerosol and gaseous chemistry representation for NGGPS, to develop and evaluate the representation of atmospheric composition, and to establish and improve the coupling with radiation and microphysics

Moisture Transport in Wood

DEFF Research Database (Denmark)

Astrup, Thomas; Hansen, Kurt Kielsgaard; Hoffmeyer, Preben

2005-01-01

Modelling of moisture transport in wood is of great importance as most mechanical and physical properties of wood depend on moisture content. Moisture transport in porous materials is often described by Ficks second law, but several observations indicate that this does not apply very well to wood....... Recently at the Technical University of Denmark, Department of Civil Engineering, a new model for moisture transport in wood has been developed. The model divides the transport into two phases, namely water vapour in the cell lumens and bound water in the cell walls....

Evaluation of fuel wood quality of four fuel tree species used for fish smoking in the Sene District of the Brong Ahafo Region of Ghana

International Nuclear Information System (INIS)

Neequaye-Tetteh, G.A.; Quashie-Sam, S.J.; Dassah, A. L.

2004-01-01

Full text. The fuel wood quality of four trees, Terminalia avicennoides, Anogeissus Ieiocarpus, Combretum ghasalense and Pterocarpus arinaceus, which are easily available and widely used as fuel wood for fish smoking in the Sene District of the Brong Ahafo Region of Ghana was assessed. The specific gravity, calorific values, and burning times were determined. The mean specific gravity values for T. avicennoides, A. leiocarpus, C. ghasalense, and P. erinaceus were 0.97, 0.96, and 0.97, respectively. These values were not significantly different (P<0.05). The calorific values were 19,368.0 kj/kg for T avicennoides, 18,905.2 kj/kg for A. leiocarpus, 18,665.8 kj/kg for C. ghasalense, and 19,694.1 kj/kg for P. erinaceus. The values were not significantly different (P<0.05) between T. avicennoides and A. leiocarpus and C. ghasalense. However, there were significant differences (P<0.05) in the calorific values between T. avicennoides and C. ghasalense, A. leiocarpus and P. erinaceus, and C. ghasalense and P. erinaceus. The time in minutes required in burning equal lengths (60 cm) of the four species of fuel wood were 360 for T. avicennoides, 260 for A. leiocarpus, 195 for C. ghasalense, and 175 for P. erinaceus. These values were significantly different (P<0.0 1), with P. erinaceus burning almost twice as fast as T. avicennoides. Ranking the four fuel wood species from least to highest burning times, T. avicennoides burnt slowest, followed by A. leiocarpus, C. ghasalense, and P. erinaceuse. The specific gravity and calorific values recorded indicate that wood from the four species is suitable for use as fuel. Terminalia avicennoides, which burnt slowest, was most preferred for fish smoking, followed by A. leiocarpus and C. ghasalense. The fast-burning P. erinaceus was least preferred for fish smoking. (au)

Worldwide Report, Environmental Quality

National Research Council Canada - National Science Library

1983-01-01

..., Environmental Impact, Forest Policy, Endangers, Water Level, Air Quality, Water Shortage, Protecting Environment,Wood Resource, Drough, Crop Failure, Water Crisis, Dams, Government Aid, Water Quality...

GLASS FIBERS – MODERN METHOD IN THE WOOD BEAMS REINFORCEMENT

Directory of Open Access Journals (Sweden)

Cătălina IANĂŞI

2017-05-01

Full Text Available : One of the defining goals of this paper is getting new resistant material which combine the qualities of basic materials that get into its composition but not to borrow from them their negative properties. Specifically, the use of GFRP composite materials as reinforcement for wood beams under bending loads requires paying attention to several aspects of the problem such as the number of the composite layers applied on the wood beams. The results obtained in this paper indicate that the behavior of reinforced beams is totally different from that of un-reinforced one. The main conclusion of the tests is that the tensioning forces allow beam taking a maximum load for a while, something that is particularly useful when we consider a real construction, The experiments have shown that the method of increasing resistance of wood constructions with composite materials is good for it and easy to implement.

Inside the guts of wood-eating catfishes: can they digest wood?

Science.gov (United States)

German, Donovan P

2009-11-01

To better understand the structure and function of the gastrointestinal (GI) tracts of wood-eating catfishes, the gross morphology, length, and microvilli surface area (MVSA) of the intestines of wild-caught Panaque nocturnus, P. cf. nigrolineatus "Marañon", and Hypostomus pyrineusi were measured, and contrasted against these same metrics of a closely related detritivore, Pterygoplichthys disjunctivus. All four species had anatomically unspecialized intestines with no kinks, valves, or ceca of any kind. The wood-eating catfishes had body size-corrected intestinal lengths that were 35% shorter than the detritivore. The MVSA of all four species decreased distally in the intestine, indicating that nutrient absorption preferentially takes place in the proximal and mid-intestine, consistent with digestive enzyme activity and luminal carbohydrate profiles for these same species. Wild-caught Pt. disjunctivus, and P. nigrolineatus obtained via the aquarium trade, poorly digested wood cellulose (<33% digestibility) in laboratory feeding trials, lost weight when consuming wood, and passed stained wood through their digestive tracts in less than 4 h. Furthermore, no selective retention of small particles was observed in either species in any region of the gut. Collectively, these results corroborate digestive enzyme activity profiles and gastrointestinal fermentation levels in the fishes' GI tracts, suggesting that the wood-eating catfishes are not true xylivores such as beavers and termites, but rather, are detritivores like so many other fishes from the family Loricariidae.

LCA-based optimization of wood utilization under special consideration of a cascading use of wood.

Science.gov (United States)

Höglmeier, Karin; Steubing, Bernhard; Weber-Blaschke, Gabriele; Richter, Klaus

2015-04-01

Cascading, the use of the same unit of a resource in multiple successional applications, is considered as a viable means to improve the efficiency of resource utilization and to decrease environmental impacts. Wood, as a regrowing but nevertheless limited and increasingly in demand resource, can be used in cascades, thereby increasing the potential efficiency per unit of wood. This study aims to assess the influence of cascading wood utilization on optimizing the overall environmental impact of wood utilization. By combining a material flow model of existing wood applications - both for materials provision and energy production - with an algebraic optimization tool, the effects of the use of wood in cascades can be modelled and quantified based on life cycle impact assessment results for all production processes. To identify the most efficient wood allocation, the effects of a potential substitution of non-wood products were taken into account in a part of the model runs. The considered environmental indicators were global warming potential, particulate matter formation, land occupation and an aggregated single score indicator. We found that optimizing either the overall global warming potential or the value of the single score indicator of the system leads to a simultaneous relative decrease of all other considered environmental impacts. The relative differences between the impacts of the model run with and without the possibility of a cascading use of wood were 7% for global warming potential and the single score indicator, despite cascading only influencing a small part of the overall system, namely wood panel production. Cascading led to savings of up to 14% of the annual primary wood supply of the study area. We conclude that cascading can improve the overall performance of a wood utilization system. Copyright © 2015 Elsevier Ltd. All rights reserved.

Greater utilization of wood residue fuels through improved financial planning

International Nuclear Information System (INIS)

Billings, C.D.; Ziemke, M.C.; Stanford, R.

1991-01-01

Recent events have focused attention on the promotion of greater utilization of biomass fuel. Considerations include the need to reduce increases in global warming and also to improve ground level air quality by limiting the use of fossil fuels. However, despite all these important environmentally related considerations, economics remains the most important factor in the decision process used to determine the feasibility of using available renewable fuels instead of more convenient fossil fuels. In many areas of the Southeast, this decision process involves choosing between wood residue fuels such as bark, sawdust and shavings and presently plentiful natural gas. The primary candidate users of wood residue fuels are industries that use large amounts of heat and electric power and are located near centers of activity in the forest products industry such as sawmills, veneer mills and furniture factories. Given that such facilities both produce wood residues and need large amounts of heat and electricity, it is understandable that these firms are often major users of wood-fired furnaces and boilers. The authors have observed that poor or incomplete financial planning by the subject firms is a major barrier to economic utilization of inexpensive and widely available renewable fuels. In this paper, the authors suggest that wider usage of improved financial planning could double the present modest annual incidence of new commercial wood-fueled installation

Creation of Wood Dust during Wood Processing: Size Analysis, Dust Separation, and Occupational Health

Directory of Open Access Journals (Sweden)

Eva Mračková

2015-11-01

Full Text Available Mechanical separators and fabric filters are being used to remove airborne fine particles generated during the processing and handling of wood. Such particles might have a harmful effect on employee health, not only in small- but also in large-scale wood processing facilities. The amount of wood dust and its dispersion conditions vary according to geometric boundary conditions. Thus, the dispersion conditions could be changed by changing the linear size of the particles. Moreover, the smaller the particles are, the more harmful they can be. It is necessary to become familiar with properties, from a health point of view, of wood dust generated from processing. Wood dust has to be sucked away from the processing area. The fractional separation efficiency of wood dust can be improved using exhaust and filtering devices. Filtration efficiency depends on moisture content, particle size, and device performance. Because of the carcinogenicity of wood dust, the concentration of wood dust in air has to be monitored regularly. Based on the results hereof, a conclusion can be made that both mechanical separators of types SEA and SEB as well as the fabric filters with FINET PES 1 textile are suitable for the separation of wet saw dust from all types of wooden waste produced within the process.

Obtaining the mass attenuation coefficient of the wood to a beam of gamma-ray of 241Am

International Nuclear Information System (INIS)

Costa, Vladimir Eliodoro; Rezende, Marcos Antonio de

2009-01-01

Full text: The quality of wood produced in Brazil reforestation has been the subject of many discussions in the Forestry Sector. SeEKXing to produce a rapid growth and wood quality, the Forestry Sector, found in Applied Nuclear Physics, a precise method of determining the density of wood known as ad hoc technique of attenuation of gamma-ray. The radioisotope used in this technique is that it has a picture 241 Am peak of 59.6 keV gamma-ray. This work has the objective of determining the mass attenuation coefficient of wood of the genus Eucalyptus for 241 Am radioisotope. We used 324 samples of wood from six different treatments: a seminal of Eucalyptus grandis; two clones of E. grandis; three clones of the hybrid E. grandis x E. urophylla. The same assay was used for the six treatments. It was determined the basic density of the samples by the method of immersion in water and then the basic density was converted into apparent density in the moisture equilibrium and it was determined the attenuation coefficient of mass. Preliminary results showed that the attenuation coefficient of mass did not vary between treatments, and its average value 0.1822 ± 0.0015. It was to here that the attenuation coefficient of mass in the wood of the genus Eucalyptus in moisture equilibrium can be constant. (author)

Impact of wood burning on outdoor air quality: existing French data and current studies; Contribution du chauffage au bois a la qualite de l'air exterieur: donnees existantes et etudes en cours en France

Energy Technology Data Exchange (ETDEWEB)

Leoz-Garziandia, E.; Mandin, C.; Collet, S. [Institut National de l' Environnement Industriel et des Risques, 60 - Verneuil en Halatte (INERIS) (France); Besombes, J.L.; Pissot, N. [Universite de Savoie, Lab. de Chimie Moleculaire et Environnemental (LCME), 73 - Le Bourget du Lac (France); Allemand, N. [Centre Interprofessionnel Technique d' Etudes de la Pollution Atmospherique, CITEPA, 75 - Paris (France); Riberon, J. [Centre Scientifique et Technique du Batiment (CSTB), 75 - Paris (France); Jaffrezo, J.L. [Laboratoire de Glaciologie et Geophysique de l' Environnement (LGGE UMR CNRS), 38 - Grenoble (France)

2009-03-15

French source apportionment studies of air quality including the wood combustion source become widespread. Quantify a single source contribution to air quality requires to be provided with a specific measurable data to this source. For that reason, numerous studies have focused on the determination, in the atmospheric samples, of the source-specific compounds, usually called molecular tracers. Since 2000, trend works focused on the 'wood combustion' contribution to air quality have been based on the use of some tracers such as levoglucosan and metoxyphenols. Obtained results have been compared to atmospheric particles global characteristics: organic carbon (OC), elementary carbon (EC), PM{sub 10}, PM{sub 2.5} and polycyclic aromatic hydrocarbons (PAH). The results presented in this article show not only the interest but also the limits of such an approach, as well as the need to develop and complete the current studies in order to quantify the different sources contribution to air quality. (author)

ELABORATION OF A DRYING SCHEDULE FOR Eucalyptus spp HYBRIDS CLONES WOODS

Directory of Open Access Journals (Sweden)

Celso Gonçalves Barbosa

2005-03-01

Full Text Available The elaboration of adequate drying schedules is essential to produce high quality conventional kiln dried lumber.Eucalyptus woods are particularly difficult to dry, and, for this reason, it is desirable that the drying schedule be carefullydeveloped. The objectives of this work were to elaborate a drying schedule for woods of ten Eucalyptus hybrids clones and toverify the propensity of these woods to post drying defects. For this purpose, it was applied the methodology of drastic drying at100°C, which associates intensity of defects, time and rate of drying, presented by small wood samples, with the behaviourto be presented by lumber after the conventional drying. The results allowed developing a drying schedule common to the tenclone lumbers. This program is based on an initial temperature of 40°C, final temperature of 66°C and drying potential equal to2.2. The drying time can be reduced, if the clones were grouped in accordance to their drying rate. The clones presented lowpropensity to split and high propensity to collapse.

Reactivity and burnout of wood fuels

DEFF Research Database (Denmark)

Dall'Ora, Michelangelo

This thesis deals with the combustion of wood in pulverised fuel power plants. In this type of boiler, the slowest step in the wood conversion process is char combustion, which is one of the factors that not only determine the degree of fuel burnout, but also affect the heat release profile...... of different aspects relevant to wood combustion, including wood structure and composition, wood pyrolysis, wood char properties and wood char oxidation. The full scale campaign, which is the subject of Chapter 3, included sampling of wood fuel before and after milling and sampling of gas and particles...... at the top of the combustion chamber. The collected samples and data are used to obtain an evaluation of the mills in operation at the power plant, the particle size distribution of the wood fuel, as well as the char conversion attained in the furnace. In Chapter 4 an experimental investigation...

Application of molecular genetic methods for identification of wood-decaying fungi in wood constructions

OpenAIRE

Elena Bobeková; Michal Tomšovský; Petr Horáček

2008-01-01

The aim of the paper is to evaluate the utilization of molecular biology methods for detection of wood decaying fungi directly from decomposed wood using a commercial DNA extraction kit developed for soil substrates (PowerSoil™ DNA isolation kit). The experiment based on dry rot fungus (Serpula lacrymans) detection from inoculated wooden pieces under laboratory conditions was followed by field detection of wood-decaying fungi from wood structures on building constructions. Fungal DNA was ide...

Long-term development of the Swedish market of energy wood

Energy Technology Data Exchange (ETDEWEB)

Dickens, C H

1980-03-01

The aim of the report is to elucidate the long-term development. The sort of wood for industrial purposes also seems to be best suited for the introduction in fuel supply. This might change the conditions precedent for the manufacturing - refining industry. The appraisement should thus cover the total wood market. The report considers three time spans namely the historical development, the description of the actual situation and an estimate of the future. The actual situation presents large regional differences which must be observed for times to come. The potential of the wood industry is its proximity to the European market, its character of long-term productivity, the technical qualifications and its unexploited opportunities as to the markets and the raw materials. The problems of the industry are the following: economy, the energy situation and the limited supply of raw products. The essential parts of the strategy of means are as follows - marketing, product development, the utilization of the qualities of the raw products, improvement of process techniques and the development of a market for energy wood and peat. The study presents recommendations of continued analysis of the market based upon regions of the size of administrative districts.

Adhesive interactions with wood

Science.gov (United States)

Charles R. Frihart

2004-01-01

While the chemistry for the polymerization of wood adhesives has been studied systematically and extensively, the critical aspects of the interaction of adhesives with wood are less clearly understood. General theories of bond formation need to be modified to take into account the porosity of wood and the ability of chemicals to be absorbed into the cell wall....

Composite structure of wood cells in petrified wood

International Nuclear Information System (INIS)

Nowak, Jakub; Florek, Marek; Kwiatek, Wojciech; Lekki, Janusz; Chevallier, Pierre; Zieba, Emil; Mestres, Narcis; Dutkiewicz, E.M.; Kuczumow, Andrzej

2005-01-01

Special kinds of petrified wood of complex structure were investigated. All the samples were composed of at least two different inorganic substances. The original cell structure was preserved in each case. The remnants of the original biological material were detected in some locations, especially in the cell walls. The complex inorganic structure was superimposed on the remnant organic network. The first inorganic component was located in the lumena (l.) of the cells while another one in the walls (w.) of the cells. The investigated arrangements were as follows: calcite (l.)-goethite-hematite (w.)-wood from Dunarobba, Italy; pyrite (l.)-calcite (w.)-wood from Lukow, Poland; goethite (l.)-silica (w.)-wood from Kwaczala, Poland. The inorganic composition was analysed and spatially located by the use of three spectral methods: electron microprobe, X-ray synchrotron-based microprobe, μ-PIXE microprobe. The accurate mappings presenting 2D distribution of the chemical species were presented for each case. Trace elements were detected and correlated with the distribution of the main elements. In addition, the identification of phases was done by the use of μ-Raman and μ-XRD techniques for selected and representative points. The possible mechanisms of the described arrangements are considered. The potential synthesis of similar structures and their possible applications are suggested

Composite structure of wood cells in petrified wood

Energy Technology Data Exchange (ETDEWEB)

Nowak, Jakub [Department of Chemistry, Catholic University of Lublin, 20-718 Lublin (Poland); Florek, Marek [Department of Chemistry, Catholic University of Lublin, 20-718 Lublin (Poland); Kwiatek, Wojciech [Institute of Nuclear Physics, Department of Nuclear Spectroscopy, 31-342 Cracow (Poland); Lekki, Janusz [Institute of Nuclear Physics, Department of Nuclear Spectroscopy, 31-342 Cracow (Poland); Chevallier, Pierre [LPS, CEN Saclay et LURE, Universite Paris-Sud, Bat 209D, F-91405 Orsay (France); Zieba, Emil [Department of Chemistry, Catholic University of Lublin, 20-718 Lublin (Poland); Mestres, Narcis [Institut de Ciencia de Materials de Barcelona (ICMAB), Campus de la UAB, E-08193-Bellaterra (Spain); Dutkiewicz, E.M. [Institute of Nuclear Physics, Department of Nuclear Spectroscopy, 31-342 Cracow (Poland); Kuczumow, Andrzej [Department of Chemistry, Catholic University of Lublin, 20-718 Lublin (Poland)

2005-04-28

Special kinds of petrified wood of complex structure were investigated. All the samples were composed of at least two different inorganic substances. The original cell structure was preserved in each case. The remnants of the original biological material were detected in some locations, especially in the cell walls. The complex inorganic structure was superimposed on the remnant organic network. The first inorganic component was located in the lumena (l.) of the cells while another one in the walls (w.) of the cells. The investigated arrangements were as follows: calcite (l.)-goethite-hematite (w.)-wood from Dunarobba, Italy; pyrite (l.)-calcite (w.)-wood from Lukow, Poland; goethite (l.)-silica (w.)-wood from Kwaczala, Poland. The inorganic composition was analysed and spatially located by the use of three spectral methods: electron microprobe, X-ray synchrotron-based microprobe, {mu}-PIXE microprobe. The accurate mappings presenting 2D distribution of the chemical species were presented for each case. Trace elements were detected and correlated with the distribution of the main elements. In addition, the identification of phases was done by the use of {mu}-Raman and {mu}-XRD techniques for selected and representative points. The possible mechanisms of the described arrangements are considered. The potential synthesis of similar structures and their possible applications are suggested.

Sustainable wood waste management in Nigeria

Directory of Open Access Journals (Sweden)

Owoyemi Jacob Mayowa

2016-09-01

Full Text Available Wood industries produce large volumes of residues which must be utilized, marketed or properly disposed of. Heaps of wood residues are common features in wood industries throughout the year. In Nigeria, this residue is generally regarded as waste and this has led to open burning practices, dumping in water bodies or dumping in an open area which constitutes environmental pollution. Sawmills in Nigeria generated over 1,000,000 m3 of wood waste in 2010 while about 5000 m3 of waste was generated in plywood mills. Nigeria generates about 1.8 million tons of sawdust annually and 5.2 million tons of wood wastes. The impact of improper disposal of waste wood on the environment affects both the aquatic and terrestrial ecosystems. Also burning of waste wood releases greenhouse gases into the atmosphere causing various health issues. Reuse/recycling of these wood residues in Nigeria will reduce the pressure on our ever decreasing forests, reduce environmental pollution, create wealth and employment. The literature available on this subject was reviewed and this article, therefore, focuses on the various methods of wood waste disposal and its utilization in Nigerian wood industries, the effects of wood waste on the environment as well as on human health and the benefits of proper wood waste management practices.

Modelling of dynamic and quasistatic events with special focus on wood-drying distortions

OpenAIRE

Ekevad, Mats

2006-01-01

This thesis deals mainly with computer simulations of wood-drying distortions, especially twist. The reason for this is that such distortions often appear in dried timber, and the results are quality downgrades and thus value losses in the wood value chain. A computer simulation is a way to theoretically simulate what happens in reality when moisture content in timber changes. If the computer simulation model is appropriate and capable of realistic simulations of real events, then it is possi...

Reactivity and burnout of wood fuels

Energy Technology Data Exchange (ETDEWEB)

Dall' Ora, M.

2011-07-01

pyrolysis temperature increased. During fast pyrolysis wood particles underwent melting, yet to different extents for the two investigated fuels: pine wood produced chars of porous spherical particles, whereas beech sawdust chars showed a somewhat less drastic change of morphology with respect to the parent fuel. Char produced by low heating rate pyrolysis fully retained the original fibrous structure of wood. Fast pyrolysis chars were significantly more reactive than slow pyrolysis chars (for the same activation energy, the pre-exponential factor was up to 2 orders of magnitude greater for chars increased). The amount and composition of the ash forming matter of the wood fuels is believed to play an important role in determining the differences in char yield, morphology and reactivity. The modelling of wood char combustion is the subject of Chapter 5. The lowest and the highest reactivities obtained for the chars produced in the EFR are used in a simple single particle combustion model in combination with a description of Avedoerevaerket's boiler. In the model the char particle is assumed to burn in a gas with constant temperature and constant oxygen fraction. The particle temperature is on the other hand determined taking reaction heat, convection through boundary gas layer and radiation into account. The model accounts for external diffusion of oxygen to the particle outer surface, internal diffusion in the pores and heterogeneous chemical reaction (CO is considered the only product). The model calculates an overall efficiency factor for combustion, yet assumes that all the reacting carbon is consumed at the outer surface of the char. The model predicts that at an average furnace temperature of 1200 K the conversion of char particles with radius 20-350 {micro}m is very much affected by the reactivity of the char. The influence of the particle's reactivity is lower at higher temperatures: at furnace temperatures of 1500 K and 1700 K the combustion of the char is

Structure and function of wood

Science.gov (United States)

Alex Wiedenhoeft

2010-01-01

Wood is a complex biological structure, a composite of many chemistries and cell types acting together to serve the needs of a living plant. Attempting to understand wood in the context of wood technology, we have often overlooked the key and basic fact that wood evolved over the course of millions of years to serve three main functions in plants― conduction of water...

Twenty-five years of post-Bretton Woods experience: some lessons

Directory of Open Access Journals (Sweden)

H. ASKARI

1999-03-01

Full Text Available In 1971 many academic economists were predicting that the Bretton Woods system of fixed parities would collapse. Some, most notably Milton Friedman, became excited about the possibility of a floating system because the benefits of international capital mobility can only be achieved through the flexibility in the exchange rate. These economists argued that a floating exchange rate system can ensure positive results more than the fixed parities system. Twenty-five years later, however, there is still no consensus on the matter. The author reviews the post-Bretton Woods experience to highlight some policies and approaches that might be helpful for the future.

Overall ecologic evaluation of cascading use of wood. Environmental impacts of substantial and energetic systems for utilization of wood in comparison; Gesamtoekologische Bewertung der Kaskadennutzung von Holz. Umweltauswirkungen stofflicher und energetischer Holznutzungssysteme im Vergleich

Energy Technology Data Exchange (ETDEWEB)

Gaertner, Sven; Hienz, Gunnar; Keller, Heiko; Mueller-Lindenlauf, Maria

2013-01-15

Wood demand is rising and its production can only be extended to a certain degree. This requires a prioritisation of wood use options. Therefore, the environmental aspects of using wood for energy production or as a material with and without cascading recycling steps of stepwise lower value are studied in a comprehensive life cycle assessment (LCA). In addition, the environmental impacts of tapping new wood resources are assessed qualitatively. The results show that under most conditions the environmental impacts are the lower the more steps of a high-value material use are performed before the wood is used for energy production. One has to consider, though, that extended material use cascades can cause decades of delays of the energy recovery step, which may lead to the replacement of cleaner energy sources in the future and thus impair the results for the long-lived wood products. At the same time, wood products can represent a temporary or even - if material wood use generally increases - a long-term carbon stock. This leads to a delay of the greenhouse effect. Depending on the assessment method, these opposing effects result in unchanged to diminished impacts of long-lived wood products on the climate. Nevertheless, from an environmental point of view, high-value material use is advantageous compared to a direct use of wood for energy production independent of the assessment method. When comparing material use options of wood, especially the high-quality use of high-value wood assortments (e.g. solid wood as construction wood) is associated with positive results from an environmental perspective. In this context, the main effects on the LCA results come from the choice of the non-wood reference product and its associated environmental impacts. Regarding the direct use of wood for energy production, the most advantageous option from an environmental point of view is a combined heat and power plant (CHP) with a high overall efficiency.

Acoustic and adsorption properties of submerged wood

Science.gov (United States)

Hilde, Calvin Patrick

Wood is a common material for the manufacture of many products. Submerged wood, in particular, is used in niche markets, such as the creation of musical instruments. An initial study performed on submerged wood from Ootsa Lake, British Columbia, provided results that showed that the wood was not suitable for musical instruments. This thesis re-examined the submerged wood samples. After allowing the wood to age unabated in a laboratory setting, the wood was retested under the hypothesis that the physical acoustic characteristics would improve. It was shown, however, that the acoustic properties became less adequate after being left to sit. The adsorption properties of the submerged wood were examined to show that the submerged wood had a larger accessible area of wood than that of control wood samples. This implied a lower amount of crystalline area within the submerged wood. From the combined adsorption and acoustic data for the submerged wood, relationships between the moisture content and speed of sound were created and combined with previous research to create a proposed model to describe how the speed of sound varies with temperature, moisture content and the moisture content corresponding to complete hydration of sorption sites within the wood.

Domestic wood combustion - practices, attitudes and regulation; Braendefyring i hjemmet - praksis, holdninger og regulering

Energy Technology Data Exchange (ETDEWEB)

Kjerulf Petersen, L.; Martinsen, L.

2008-06-15

Use of wood burning stoves for domestic heating is the subject of this report which is based on results from an interview study and a survey. The report is concerned with why people have and use stoves, how they use them and which functions the stoves serve in their homes. Of equal interest are the attitudes of users as well as non-users to environmental consequences of wood combustion and to different forms of regulation. There can be several reasons for having and using a wood burning stove for domestic heating. The main reason seems to be the sense of homeliness and cosiness and calm that it gives to the home, and the second most important reason is the economic advantages it implies in terms of reducing heating expenses. Enjoyment of the particular quality of warmth that stoves can provide and a desire to obtain higher indoor temperature are important additional motivations, while self determination in household heating supply runs through all these motivations as an underlying incentive. Potential environmental problems from domestic wood combustion depend on the properties of the stove, on the quality of the fuel, and on air intake and other aspects of the combustion process; and practices of stove users play an important role in all this. For stove users there are both sensuous experiences and social norms - e.g. regarding use of damp wood or any other type of fuel than pure wood - that support an environmentally appropriate practice. However, this study shows that even though users are inclined to follow environmentally sound practices for wood combustion other considerations in everyday life may be more important; considerations regarding what kind of effort one has time and energy for, what is practically feasible, what one can be bothered to consider, and what level of thermal comfort one wants. Almost half of the respondents, users and non-users alike, are to some extend - from slightly to extremely - bothered by smoke from wood combustion, and around

Urban Wood Waste Resource Assessment; TOPICAL

International Nuclear Information System (INIS)

Wiltsee, G.

1998-01-01

This study collected and analyzed data on urban wood waste resources in 30 randomly selected metropolitan areas in the United States. Three major categories wood wastes disposed with, or recovered from, the municipal solid waste stream; industrial wood wastes such as wood scraps and sawdust from pallet recycling, woodworking shops, and lumberyards; and wood in construction/demolition and land clearing debris

Moisture Performance of wood-plastic composites reinforced with extracted and delignified wood flour

Science.gov (United States)

Yao Chen; Nicole M. Stark; Mandla A. Tshabalala; Jianmin Gao; Yongming Fan

2014-01-01

This study investigated the effect of using extracted and delignified wood flour on water sorption properties of wood–plastic composites. Wood flour (WF) extraction was performed with three solvent systems: toluene/ethanol (TE), acetone/water (AW), and hot water (HW); delignification was conducted using sodium chlorite/acetic acid solution. A 24 full-factorial...

GLOBAL WOOD PELLET INDUSTRY AND MARKET – CURRENT DEVELOPMENTS AND OUTLOOK

Energy Technology Data Exchange (ETDEWEB)

Thrän, Daniela; Peetz, David; Schaubach, Kay; Trømborg, Erik; Pellini, Alessandro; Lamers, Patrick; Hess, J. Richard; Schipfer, Fabian; Hektor, Bo; Olsson, Olle; Bruce, Lena; Stelte, Wolfgang; Proskurina, Svetlana; Heinimo, Jussi; Benedetti, Luca; Mai-Moulin, Thuy; Junginger, Martin; Craggs, Laura; Wild, Michael; Murray, Gordan; Diaz-Chavez, Rocio; Thiermann, Ute; Escobar, F. J.; Goldemberg, J.; Coelho, S. T.

2017-06-01

The wood pellet use in the heating and electricity sector has recorded a steady growth in the last years. IEA bioenergy task 40 carried out an update of the situation on the national pellet markets in the most relevant pellet producing countries and the global development as well. Various country specific data is collected and compiled for more than 30 countries, containing updated information about regulatory framework, production, consumption, price trends, quality standards and trade aspects. The analysis confirmed the positive development in terms of production and consumption of wood pellets in almost all countries. In 2015 more than 26 Mt of wood pellets have been produced and consumed worldwide. Technologies and markets become more mature. Increased international pellet trade needs to be supported by adequate frame condition not only for commerce, but also with regard to sustainability issues.

Survival, growth, wood basic density and wood biomass of seven ...

African Journals Online (AJOL)

A performance comparison of seven-year-old individuals of 13 Casuarina species/provenances in terms of survival, growth (diameter, height and volume), wood basic density and wood biomass was undertaken at Kongowe, Kibaha, Tanzania. The trial was laid out using a randomised complete block design with four ...

Chapter 9: Wood Energy

Science.gov (United States)

Francisco X. Aguilar; Karen Abt; Branko Glavonjic; Eugene Lopatin; Warren  Mabee

2016-01-01

The availabilty of information on wood energy continues to improve, particularly for commoditized woodfuels.  Wood energy consumption and production vary in the UNECE region because demand is strngly affected by weather and the prices of competing energy sources.  There has been an increase in wood energy in the power-and-heat sector in the EU28 and North American...

Iron Stain on Wood

Science.gov (United States)

Mark Knaebe

2013-01-01

Iron stain, an unsightly blue–black or gray discoloration, can occur on nearly all woods. Oak, redwood, cypress, and cedar are particularly prone to iron stain because these woods contain large amounts of tannin-like extractives. The discoloration is caused by a chemical reaction between extractives in the wood and iron in steel products, such as nails, screws, and...

On-line automatic detection of wood pellets in pneumatically conveyed wood dust flow

Science.gov (United States)

Sun, Duo; Yan, Yong; Carter, Robert M.; Gao, Lingjun; Qian, Xiangchen; Lu, Gang

2014-04-01

This paper presents a piezoelectric transducer based system for on-line automatic detection of wood pellets in wood dust flow in pneumatic conveying pipelines. The piezoelectric transducer senses non-intrusively the collisions between wood pellets and the pipe wall. Wavelet-based denoising is adopted to eliminate environmental noise and recover the collision events. Then the wood pellets are identified by sliding a time window through the denoised signal with a suitable threshold. Experiments were carried out on a laboratory test rig and on an industrial pneumatic conveying pipeline to assess the effectiveness and operability of the system.

NOAA's National Air Quality Prediction and Development of Aerosol and Atmospheric Composition Prediction Components for NGGPS

Science.gov (United States)

Stajner, I.; McQueen, J.; Lee, P.; Stein, A. F.; Wilczak, J. M.; Upadhayay, S.; daSilva, A.; Lu, C. H.; Grell, G. A.; Pierce, R. B.

2017-12-01

NOAA's operational air quality predictions of ozone, fine particulate matter (PM2.5) and wildfire smoke over the United States and airborne dust over the contiguous 48 states are distributed at http://airquality.weather.gov. The National Air Quality Forecast Capability (NAQFC) providing these predictions was updated in June 2017. Ozone and PM2.5 predictions are now produced using the system linking the Community Multiscale Air Quality model (CMAQ) version 5.0.2 with meteorological inputs from the North American Mesoscale Forecast System (NAM) version 4. Predictions of PM2.5 include intermittent dust emissions and wildfire emissions from an updated version of BlueSky system. For the latter, the CMAQ system is initialized by rerunning it over the previous 24 hours to include wildfire emissions at the time when they were observed from the satellites. Post processing to reduce the bias in PM2.5 prediction was updated using the Kalman filter analog (KFAN) technique. Dust related aerosol species at the CMAQ domain lateral boundaries now come from the NEMS Global Aerosol Component (NGAC) v2 predictions. Further development of NAQFC includes testing of CMAQ predictions to 72 hours, Canadian fire emissions data from Environment and Climate Change Canada (ECCC) and the KFAN technique to reduce bias in ozone predictions. NOAA is developing the Next Generation Global Predictions System (NGGPS) with an aerosol and gaseous atmospheric composition component to improve and integrate aerosol and ozone predictions and evaluate their impacts on physics, data assimilation and weather prediction. Efforts are underway to improve cloud microphysics, investigate aerosol effects and include representations of atmospheric composition of varying complexity into NGGPS: from the operational ozone parameterization, GOCART aerosols, with simplified ozone chemistry, to CMAQ chemistry with aerosol modules. We will present progress on community building, planning and development of NGGPS.

Researches of fruit quality prediction model based on near infrared spectrum

Science.gov (United States)

Shen, Yulin; Li, Lian

2018-04-01

With the improvement in standards for food quality and safety, people pay more attention to the internal quality of fruits, therefore the measurement of fruit internal quality is increasingly imperative. In general, nondestructive soluble solid content (SSC) and total acid content (TAC) analysis of fruits is vital and effective for quality measurement in global fresh produce markets, so in this paper, we aim at establishing a novel fruit internal quality prediction model based on SSC and TAC for Near Infrared Spectrum. Firstly, the model of fruit quality prediction based on PCA + BP neural network, PCA + GRNN network, PCA + BP adaboost strong classifier, PCA + ELM and PCA + LS_SVM classifier are designed and implemented respectively; then, in the NSCT domain, the median filter and the SavitzkyGolay filter are used to preprocess the spectral signal, Kennard-Stone algorithm is used to automatically select the training samples and test samples; thirdly, we achieve the optimal models by comparing 15 kinds of prediction model based on the theory of multi-classifier competition mechanism, specifically, the non-parametric estimation is introduced to measure the effectiveness of proposed model, the reliability and variance of nonparametric estimation evaluation of each prediction model to evaluate the prediction result, while the estimated value and confidence interval regard as a reference, the experimental results demonstrate that this model can better achieve the optimal evaluation of the internal quality of fruit; finally, we employ cat swarm optimization to optimize two optimal models above obtained from nonparametric estimation, empirical testing indicates that the proposed method can provide more accurate and effective results than other forecasting methods.

Image processing system performance prediction and product quality evaluation

Science.gov (United States)

Stein, E. K.; Hammill, H. B. (Principal Investigator)

1976-01-01

The author has identified the following significant results. A new technique for image processing system performance prediction and product quality evaluation was developed. It was entirely objective, quantitative, and general, and should prove useful in system design and quality control. The technique and its application to determination of quality control procedures for the Earth Resources Technology Satellite NASA Data Processing Facility are described.

State-of-the-art of the European regulation on wood wastes and wood ashes valorization. Synthesis

International Nuclear Information System (INIS)

Mousseau, S.

2007-01-01

This study has the objective of comparing the regulations of 10 European countries with that of France, in relation to the classification and recycling of wood waste, in particular lightly treated wood, as well as recycling of wood ash. The first part relating to wood waste presents a detailed analysis by country as well as a summary, on the one hand, of the various sectors for recycling waste wood and, on the other, the emission limits for their energy recovery. Generally, there is a distinction between waste covered by the incineration directive, and the others, without any particular category for lightly treated wood. However, recommendations emerge from this that are based essentially on the regulations or guidelines observed in Germany, Austria and the United Kingdom. The second part relating to wood ash also a presents a detailed analysis by country as well as a summary of the various sectors of recycling and limit values for spreading. Ash is generally considered as waste, and is recycled on a case-by case basis. Only Germany and Austria have clearly integrated wood ash in their regulatory framework. Overall this study shows the need for uniform regulation at European level, establishing environment requirements for recycling wood waste and wood ash, in order to encourage development of the use of biomass

Accelerated Air-coupled Ultrasound Imaging of Wood Using Compressed Sensing

Directory of Open Access Journals (Sweden)

Yiming Fang

2015-12-01

Full Text Available Air-coupled ultrasound has shown excellent sensitivity and specificity for the nondestructive imaging of wood-based material. However, it is time-consuming, due to the high scanning density limited by the Nyquist law. This study investigated the feasibility of applying compressed sensing techniques to air-coupled ultrasound imaging, aiming to reduce the number of scanning lines and then accelerate the imaging. Firstly, an undersampled scanning strategy specified by a random binary matrix was proposed to address the limitation of the compressed sensing framework. The undersampled scanning can be easily implemented, while only minor modification was required for the existing imaging system. Then, discrete cosine transform was selected experimentally as the representation basis. Finally, orthogonal matching pursuit algorithm was utilized to reconstruct the wood images. Experiments on three real air-coupled ultrasound images indicated the potential of the present method to accelerate air-coupled ultrasound imaging of wood. The same quality of ACU images can be obtained with scanning time cut in half.

Evaluation of bolted connections in wood-plastic composites

Science.gov (United States)

Arnandha, Yudhi; Satyarno, Iman; Awaludin, Ali; Irawati, Inggar Septia; Ihsan, Muhamad; Wijanarko, Felyx Biondy; William, Mahdinur, Fardhani, Arfiati

2017-03-01

Wood-plastic composite (WPC) is a relatively new material that consists of sawdust and plastic polymer using the extrusion process. Due to its attributes such as low water content, low maintenance, UV durability and being fungi and termite resistant. Nowadays, WPC has already been produced in Indonesia using sawdust from local wood such as Albizia (Paraserianthes falcataria) and Teak (Tectona grandis). Moreover preliminary studies about the physical and mechanical WPC board from Albizia sawdust and HDPE plastic have been carried out. Based on these studies, WPC has a high shear strength around 25-30 MPa higher than its original wood shear strength. This paper was a part of the research in evaluating WPC as potential sheathing in a shear wall system. Since still little is known about connection behavior in WPC using Indonesian local wood, this study evaluated the connection for both of these two types of wood-plastic composite. WPC board from Albizia sawdust will be projected as shear wall sheathing and WPC stud from Teak sawdust projected to be shear wall frame. For this study, the embedding strength for both WPC was determined according to ASTM D 5764 standard, using two types of bolts (stainless bolt and standard bolt) with several diameters as variation (6 mm, 8 mm, 10 and 12 mm). Hence, dowel-bearing test under fastened condition conducted accordance to ASTM D5652, hereby the yield strength then compared with the prediction yield strength from European Yield Model (EYM). According to both single and double shear connection, it can be concluded that yield strength from the EYM method tended to under-predict the 5% diameter offset yield than the actual yield strength from the test. The yield strength itself increase with the increase of bolt diameter. For single shear connection, the highest yield strength was 12 mm standard bolt around 9732 N, slightly higher than stainless bolt around 9393 N. Whereby for double shear connection, the highest yield strength was

PENGARUH SERVICE QUALITY, PRODUCT QUALITY DAN PERCEIVED VALUE TERHADAP KEPUASAN DAN LOYALITAS PELANGGAN INDUSTRI KAYU PERHUTANI

Directory of Open Access Journals (Sweden)

Winarni Saftarya Timedina Gultom

2016-07-01

Full Text Available The purpose of this research is to analyze the influences of service quality, product quality and perceived value on the satisfaction and loyalty of the customers of Perhutani wood industry, the level of customer satisfaction and loyalty and managerial implications. Four data analysis techniques were used including the structural equation modeling partial least squares (SEMPLS with 24 exogenous latent variable attributes and 6 endogenous latent variable attributes; CSI, CLI and IPA. SEMPLS results showed that the variables of service quality (T-statistic=2, 79*>T-table=1, 96 and product quality (T-statistic=6, 45*>T-table=1, 96 significantly influence the satisfaction of the customers of Perhutani wood industry. Perceived value variable (T-statistic=0, 65quality, product quality, and perceived value provided by Perhutani wood industry. The main priority of the performances to be improved based on IPA include the attributes of accuracy of product sizes: length, width, thickness, complaint handling, product delivery, service employees, comprehension of needs, officer awareness, information on the documents and prevailing prices, service time completion, purchase document accuracy, price certainty, allocation certainty, suitability prices with quality, and affordable product prices.Keywords: perhutani, wood industry, satisfaction, loyalty, SEMPLS

Prediction of bread-making quality using size exclusion high ...

African Journals Online (AJOL)

Variation in the distribution of protein molecular weight in wheat (Triticum aestivum), influences breadmaking quality of wheat cultivars, resulting in either poor or good bread. The objective of this study was to predict breadmaking quality of wheat cultivars using size exclusion high performance liquid chromatography.

Wood Flour Moulding Technology: Implications for Technical ...

African Journals Online (AJOL)

The intent of this article is to demonstrate how wood waste called sawdust or wood flour can be transformed by plastic moulding machine into items of economic value. Wood flour is wood reduced to very fine particle form. It can be waste product from saw mills, wood working plants or produced from selected dry wood by ...

Wood wastes: Uses

International Nuclear Information System (INIS)

Cipro, A.

1993-01-01

The 1,500 industrial firms manufacturing furniture in the Italian Province of Treviso can generate up to 190,000 tonnes of wood wastes annually. In line with the energy conservation-environmental protection measures contained in Italian Law No. 475/88, this paper indicates convenient uses for these wood wastes - as a raw material for fibreboards or as a fuel to be used in the furniture manufacturing plants themselves and in kilns producing lime. Reference is made to the wood wastes gasification/power generation system being developed by ENEA (the Italian Agency for New Technology, Energy and the Environment)

Fire Safety Design of Wood Structures

DEFF Research Database (Denmark)

Hertz, Kristian Dahl

2006-01-01

Lecture Notes on Fire Safety Design of Wood Structures including charring of wood and load bearing capacity of beams, columns, and connections.......Lecture Notes on Fire Safety Design of Wood Structures including charring of wood and load bearing capacity of beams, columns, and connections....

WOOD BIOMASS FOR ENERGY IN MONTENEGRO

Directory of Open Access Journals (Sweden)

Gradimir Danon

2010-01-01

Full Text Available Wood biomass has got its place in the energy balance of Montenegro. A little more than 6% of the total energy consumption is obtained by burning wood. Along with the appropriate state measures, it is economically and environmentally justified to expect Montenegro to more than double the utilization of the existing renewable energy sources including wood biomass, in the near future. For the purpose of achieving this goal, ‘Commercial Utilisation of the Wood Residue as a Resource for Economic Development in the North of Montenegro' project was carried out in 2007. The results of this project were included in the plan of the necessary interventions of the Government and its Agencies, associations or clusters, non-government organisations and interested enterprises. The plan was made on the basis of the wood residue at disposal and the attitude of individual subjects to produce and/or use solid bio-fuels and consists of a proposal of collection and utilisation of the wood residue for each individual district in the north of Montenegro. The basic factors of sustainability of future commercialisation of the wood residue were: availability of the wood raw material, and thereby the wood residue; the development of wood-based fuel markets, and the size of the profit.

Corrosion of Fasteners in Wood Treated with Newer Wood Preservatives

Science.gov (United States)

Samuel L. Zelinka

2013-01-01

This document compiles recent research findings related to corrosion of metals in preservative treated wood into a single report on corrosion of metals in wood. The research was conducted as part of the Research, Technology and Education portion of the National Historic Covered Bridge Preservation (NHCBP) Program administered by the Federal Highway Administration. The...

On the role of CFRP reinforcement for wood beams stiffness

Science.gov (United States)

Ianasi, A. C.

2015-11-01

In recent years, carbon fiber composites have been increasingly used in different ways in reinforcing structural elements. Specifically, the use of composite materials as a reinforcement for wood beams under bending loads requires paying attention to several aspects of the problem such as the number of the composite layers applied on the wood beams. Study consolidation of composites revealed that they are made by bonding fibrous material impregnated with resin on the surface of various elements, to restore or increase the load carrying capacity (bending, cutting, compression or torque) without significant damage of their rigidity. Fibers used in building applications can be fiberglass, aramid or carbon. Items that can be strengthened are concrete, brick, wood, steel and stone, and in terms of structural beams, walls, columns and floors. This paper describes an experimental study which was designed to evaluate the effect of composite material on the stiffness of the wood beams. It proposes a summary of the fundamental principles of analysis of composite materials and the design and use. The type of reinforcement used on the beams is the carbon fiber reinforced polymer (CFRP) sheet and plates and also an epoxy resin for bonding all the elements. Structural epoxy resins remain the primary choice of adhesive to form the bond to fiber-reinforced plastics and are the generally accepted adhesives in bonded CFRP-wood connections. The advantages of using epoxy resin in comparison to common wood-laminating adhesives are their gap-filling qualities and the low clamping pressures that are required to form the bond between carbon fiber plates or sheets and the wood beams. Mechanical tests performed on the reinforced wood beams showed that CFRP materials may produce flexural displacement and lifting increases of the beams. Observations of the experimental load-displacement relationships showed that bending strength increased for wood beams reinforced with CFRP composite plates

Power generation from waste wood

Energy Technology Data Exchange (ETDEWEB)

Nitsche, H

1980-04-18

Since the energy crisis, power generation from waste wood has become increasingly important. The most profitable way to use waste wood in woodworking plants with an annual production of 100 to 150,000 m/sup 3/ solid measure of wood chips and bark is by combustion and thermal energy recovery. In plants with an annual production of 10,000 m/sup 3/ solid measure of wood chips and bark, electric power generation is a suitable application.

Wood drying project with solar energy and absorption plant; Proyecto de un secador de madera con energia solar termica y una planta de absorcion

Energy Technology Data Exchange (ETDEWEB)

Corretger, J. M.; Lara, J.; Arnau, J.; Marquez, A.

2004-07-01

Wood drying processes currently are developed in tunnel dryers using an air hot flow through the wood to remove the water. These processes are interesting to dry current wood that does not require special control of the drying velocity. However, could be necessary to control drying velocity at any moment of the process in order to dry some high quality wood. This implies to combine heating processes, cooling and dehumidification processes and humidification processes. The aim of this project is to dry noble woods with a drying complex process, in order to improve the quality of the products and to increase the energy saving by free-cooling operations and advanced control strategies, increased by using solar energy to get cold and hot water. The saving of energy will produce a bill reduction and an important minimization of environmental impact. (Author)

Status of wood energy applications

International Nuclear Information System (INIS)

Zerbe, J.I.

1991-01-01

In this address, the potential of wood and wood residues to supply future energy needs is examined. In addition, the possible environmental impact of the use of wood fuels on global climate change is discussed. Technologies for the development of new fuels are described

Choosing Wood Burning Appliances

Science.gov (United States)

Information to assist consumers in choosing a wood burning appliance, including types of appliances, the differences between certified and non-certified appliances, and alternative wood heating options.

Integrated Procurement of Pulpwood and Energy Wood by Whole-Tree Bundling

Energy Technology Data Exchange (ETDEWEB)

Jylhae, Paula (Finnish Forest Research Inst., Kannus Unit, P.O. Box 44, FI-69101 Kannus (Finland)); Kaerhae, Kalle (Metsaeteho Oy, P.O. Box 101, FI-00171 Helsinki (Finland)); Laitila, Juha (Finnish Forest Research Inst., Joensuu Unit, P.O. Box 68, FI-80101 Joensuu (Finland))

2008-10-15

Total supply chain costs of pulpwood and energy wood harvested from early thinnings can be reduced by applying an integrated procurement system based on whole-tree bundling using a newly-developed whole-tree bundler. Pulpwood-dimensioned whole trees are incorporated into pulpwood bundles. The pulp and energy fraction are not separated before the wood reaches the debarking drum of the pulp mill. Based on industrial trials with Scots pine harvested from first thinnings, pulp made from blend of bundles and conventional pulpwood meets the quality requirements of chemical pine pulp. Small-diameter trees and undesirable tree species can be accumulated into separate energy wood bundles, which are transported to energy generation. Due to load compaction, cost savings are expected especially in forest haulage and road transportation. The system shows greatest potential when harvesting first-thinning stands with a breast-height diameter of 7-10 cm

Evaluation of model quality predictions in CASP9

KAUST Repository

Kryshtafovych, Andriy

2011-01-01

CASP has been assessing the state of the art in the a priori estimation of accuracy of protein structure prediction since 2006. The inclusion of model quality assessment category in CASP contributed to a rapid development of methods in this area. In the last experiment, 46 quality assessment groups tested their approaches to estimate the accuracy of protein models as a whole and/or on a per-residue basis. We assessed the performance of these methods predominantly on the basis of the correlation between the predicted and observed quality of the models on both global and local scales. The ability of the methods to identify the models closest to the best one, to differentiate between good and bad models, and to identify well modeled regions was also analyzed. Our evaluations demonstrate that even though global quality assessment methods seem to approach perfection point (weighted average per-target Pearson\\'s correlation coefficients are as high as 0.97 for the best groups), there is still room for improvement. First, all top-performing methods use consensus approaches to generate quality estimates, and this strategy has its own limitations. Second, the methods that are based on the analysis of individual models lag far behind clustering techniques and need a boost in performance. The methods for estimating per-residue accuracy of models are less accurate than global quality assessment methods, with an average weighted per-model correlation coefficient in the range of 0.63-0.72 for the best 10 groups.

New Insights on Wood Dimensional Stability Influenced by Secondary Metabolites: The Case of a Fast-Growing Tropical Species Bagassa guianensis Aubl.

Directory of Open Access Journals (Sweden)

Julie Bossu

Full Text Available Challenging evaluation of tropical forest biodiversity requires the reporting of taxonomic diversity but also the systematic characterization of wood properties in order to discover new promising species for timber industry. Among wood properties, the dimensional stability is regarded as a major technological characteristic to validate whether a wood species is adapted to commercial uses. Cell structure and organization are known to influence the drying shrinkage making wood density and microfibrils angle markers of choice to predict wood dimensional stability. On the contrary the role of wood extractive content remains unclear. This work focuses on the fast-growing tropical species Bagassa guianensis and we report herein a correlation between heartwood drying shrinkage and extractive content. Chemical extractions and shrinkage experiments were performed on separate wood twin samples to better evaluate correctly how secondary metabolites influence the wood shrinkage behaviour. Extractive content were qualitatively and quantitatively analysed using HPLC and NMR spectroscopy. We found that B guianensis heartwood has a homogeneous low shrinkage along its radius that could not be explained only by its basic density. In fact the low drying shrinkage is correlated to the high extractive content and a corrected model to improve the prediction of wood dimensional stability is presented. Additionally NMR experiments conducted on sapwood and heartwood extracts demonstrate that secondary metabolites biosynthesis occurs in sapwood thus revealing B. guianensis as a Juglans-Type heartwood formation. This work demonstrates that B. guianensis, a fast-growing species associated with high durability and high dimensional stability, is a good candidate for lumber production and commercial purposes.

Bacterial Community Succession in Pine-Wood Decomposition.

Science.gov (United States)

Kielak, Anna M; Scheublin, Tanja R; Mendes, Lucas W; van Veen, Johannes A; Kuramae, Eiko E

2016-01-01

Though bacteria and fungi are common inhabitants of decaying wood, little is known about the relationship between bacterial and fungal community dynamics during natural wood decay. Based on previous studies involving inoculated wood blocks, strong fungal selection on bacteria abundance and community composition was expected to occur during natural wood decay. Here, we focused on bacterial and fungal community compositions in pine wood samples collected from dead trees in different stages of decomposition. We showed that bacterial communities undergo less drastic changes than fungal communities during wood decay. Furthermore, we found that bacterial community assembly was a stochastic process at initial stage of wood decay and became more deterministic in later stages, likely due to environmental factors. Moreover, composition of bacterial communities did not respond to the changes in the major fungal species present in the wood but rather to the stage of decay reflected by the wood density. We concluded that the shifts in the bacterial communities were a result of the changes in wood properties during decomposition and largely independent of the composition of the wood-decaying fungal communities.

Wood power in North Carolina

Energy Technology Data Exchange (ETDEWEB)

Cleland, J.G.; Guessous, L. [Research Triangle Institute, Research Triangle Park, NC (United States)

1993-12-31

North Carolina (NC) is one of the most forested states, and supports a major wood products industry. The NC Department of Natural Resources sponsored a study by Research Triangle Institute to examine new, productive uses of the State`s wood resources, especially electric power generation by co-firing with coal. This paper summarizes our research of the main factors influencing wood power generation opportunities, i.e., (1) electricity demand; (2) initiative and experience of developers; (3) available fuel resources; (4) incentives for alternate fuels; and (5) power plant technology and economics. The results cover NC forests, short rotation woody crops, existing wood energy facilities, electrical power requirements, and environmental regulations/incentives. Quantitative assessments are based on the interests of government agencies, utilities, electric cooperatives, developers and independent power producers, forest products industries, and the general public. Several specific, new opportunities for wood-to-electricity in the State are identified and described. Comparisons are made with nationwide resources and wood energy operations. Preferred approaches in NC are co-generation in existing or modified boilers and in dedicated wood power plants in forest industry regions. Co-firing is mainly an option for supplementing unreliable primary fuel supplies to existing boilers.

The Carbon Impacts of Wood Products

Science.gov (United States)

Richard Bergman; Maureen Puettmann; Adam Taylor; Kenneth E. Skog

2014-01-01

Wood products have many environmental advantages over nonwood alternatives. Documenting and publicizing these merits helps the future competitiveness of wood when climate change impacts are being considered. The manufacture of wood products requires less fossil fuel than nonwood alternative building materials such as concrete, metals, or plastics. By nature, wood is...

The influence of irradiated wood filler on some properties of polypropylene - wood composites

Directory of Open Access Journals (Sweden)

Điporović-Momčilović Milanka

2007-01-01

Full Text Available The problem of compatibility between the wood filler and thermoplastic matrix is of essential importance in composite production. Numerous methods have been developed for increasing this compatibility, which is still representing a challenging objective of composite research throughout the world. The research into these methods is primarily directed towards their efficiency from the viewpoint of the composite performance and their economical acceptability. The latter is of particular importance for the composite production in the developing countries with respect to the shortage of the corresponding funds. With this respect, the utilization of ionizing radiation might have considerable advantages. In this research, the beech wood flour was irradiated by a dose of 10 kGy of 60Co gamma rays for purpose of provoking the changes by the ionizing effect. The effects of ionizing radiation upon the properties of wood particles have been examined by IR spectroscopy and by determination of contents of hydroxyl groups in wood by acetylating as an indirect method. All these methods have been expected to reveal the chemical effects of the applied radiation treatment. The irradiated and the control wood flour were used in order to produce the samples of composite with polypropylene. The polypropylene-wood flour (PP-WF composites were produced with 40% of wood particles having fraction size 0.3 mm. The melt-blended composites were modified with amido-acrylic acid (AMACA as a new coupling agent synthesized for this propose in amount of 6 wt.% (based on wood filler and successively with 0.05 wt.% (based on PP of organic peroxide during mixing step. The composites containing coupling agents showed superior mechanical properties, compared to the untreated one. The highest extent of improvement of tensile was achieved in PP-WFl composites modified with AMACA coupling agent.

Ambient air quality predictions in the Athabasca oil sands region

International Nuclear Information System (INIS)

1996-01-01

This report presents dispersion modelling predictions for SO 2 , NOx, CO, HC and particulate matter (PM), which complement regional monitoring observations. The air quality simulation models provide a scientific means of relating industrial emissions to changes in ambient air quality. The four models applied to the emission sources in the region were: (1) SCREEN3, (2) ISC3BE, (3) ADEPT2, and (4) the box model. Model predictions were compared to air quality guidelines. It was concluded that the largest SO 2 concentrations were associated with intermittent flaring, and with the Suncor Powerhouse whose emissions are continuous. 45 refs., 36 tabs., 40 figs

Methane from wood

Energy Technology Data Exchange (ETDEWEB)

Schulz, T. F.; Barreto, L.; Kypreos, S.; Stucki, S

2005-07-15

The role of wood-based energy technologies in the Swiss energy system in the long-term is examined using the energy-system Swiss MARKAL model. The Swiss MARKAL model is a 'bottom-up' energy-systems optimization model that allows a detailed representation of energy technologies. The model has been developed as a joint effort between the Energy Economics Group (EEG) at Paul Scherrer Institute PSI) and the University of Geneva and is currently used at PSI-EEG. Using the Swiss MARKAL model, this study examines the conditions under which wood-based energy technologies could play a role in the Swiss energy system, the most attractive pathways for their use and the policy measures that could support them. Given the involvement of PSI in the ECOGAS project, especial emphasis is put on the production of bio-SNG from wood via gasification and methanation of syngas and on hydrothermal gasification of woody biomass. Of specific interest as weIl is the fraction of fuel used in passenger cars that could be produced by locally harvested wood. The report is organized as follows: Section 2 presents a brief description of the MARKAL model. Section 3 describes the results of the base case scenario, which represents a plausible, 'middle-of-the-road' development of the Swiss energy system. Section 4 discusses results illustrating the conditions under which the wood-based methanation technology could become competitive in the Swiss energy market, the role of oil and gas prices, subsidies to methanation technologies and the introduction of a competing technology, namely the wood-based Fischer-Tropsch synthesis. FinaIly, section 5 outlines some conclusions from this analysis. (author)

Methane from wood

International Nuclear Information System (INIS)

Schulz, T. F.; Barreto, L.; Kypreos, S.; Stucki, S.

2005-07-01

The role of wood-based energy technologies in the Swiss energy system in the long-term is examined using the energy-system Swiss MARKAL model. The Swiss MARKAL model is a 'bottom-up' energy-systems optimization model that allows a detailed representation of energy technologies. The model has been developed as a joint effort between the Energy Economics Group (EEG) at Paul Scherrer Institute PSI) and the University of Geneva and is currently used at PSI-EEG. Using the Swiss MARKAL model, this study examines the conditions under which wood-based energy technologies could play a role in the Swiss energy system, the most attractive pathways for their use and the policy measures that could support them. Given the involvement of PSI in the ECOGAS project, especial emphasis is put on the production of bio-SNG from wood via gasification and methanation of syngas and on hydrothermal gasification of woody biomass. Of specific interest as weIl is the fraction of fuel used in passenger cars that could be produced by locally harvested wood. The report is organized as follows: Section 2 presents a brief description of the MARKAL model. Section 3 describes the results of the base case scenario, which represents a plausible, 'middle-of-the-road' development of the Swiss energy system. Section 4 discusses results illustrating the conditions under which the wood-based methanation technology could become competitive in the Swiss energy market, the role of oil and gas prices, subsidies to methanation technologies and the introduction of a competing technology, namely the wood-based Fischer-Tropsch synthesis. FinaIly, section 5 outlines some conclusions from this analysis. (author)

Temperature effects on wood anatomy, wood density, photosynthesis and biomass partitioning of Eucalyptus grandis seedlings.

Science.gov (United States)

Thomas, D S; Montagu, K D; Conroy, J P

2007-02-01

Wood density, a gross measure of wood mass relative to wood volume, is important in our understanding of stem volume growth, carbon sequestration and leaf water supply. Disproportionate changes in the ratio of wood mass to volume may occur at the level of the whole stem or the individual cell. In general, there is a positive relationship between temperature and wood density of eucalypts, although this relationship has broken down in recent years with wood density decreasing as global temperatures have risen. To determine the anatomical causes of the effects of temperature on wood density, Eucalyptus grandis W. Hill ex Maiden seedlings were grown in controlled-environment cabinets at constant temperatures from 10 to 35 degrees C. The 20% increase in wood density of E. grandis seedlings grown at the higher temperatures was variously related to a 40% reduction in lumen area of xylem vessels, a 10% reduction in the lumen area of fiber cells and a 10% increase in fiber cell wall thickness. The changes in cell wall characteristics could be considered analogous to changes in carbon supply. Lumen area of fiber cells declined because of reduced fiber cell expansion and increased fiber cell wall thickening. Fiber cell wall thickness was positively related to canopy CO2 assimilation rate (Ac), which increased 26-fold because of a 24-fold increase in leaf area and a doubling in leaf CO2 assimilation rate from minima at 10 and 35 degrees C to maxima at 25 and 30 degrees C. Increased Ac increased seedling volume, biomass and wood density; but increased wood density was also related to a shift in partitioning of seedling biomass from roots to stems as temperature increased.

EVALUATION OF CEMENT-BONDED PARTICLE BOARD PRODUCED FROM AFZELIA AFRICANA WOOD RESIDUES

Directory of Open Access Journals (Sweden)

OLUFEMI A. SOTANNDE

2012-12-01

Full Text Available The study was design to evaluate the physical and mechanical properties of cement-bonded particleboards produced from Afzelia africana wood residues. The production variables investigated were three wood particle types (flakes, flake-sawdust mix and sawdust, three chemical accelerators (CaCl2, MgCl2 and AlCl3 and four wood-cement ratios (1:2.0, 1:2.5, 1:3.0 and 1:3.5. The accelerators were based on 2% by weight of cement used. The boards produced were subjected to physical tests such as density, percentage water absorption and thickness swelling. Mechanical properties evaluated were modulus of rupture, internal bonding strength and compressive strength. The results revealed that the type of particle used, wood-cement ratio and chemical additives had a marked influence on the physical and mechanical properties of the boards (p < 0.05. From quality view point, flake-sawdust composite ranked best while flake boards ranked least. Similarly, CaCl2 had the best influence on the setting of the boards followed by MgCl2 and AlCl3. Finally, it has been shown that particle boards that satisfied the BISON type HZ requirement and ISO 8335 can be produced from Afzelia africana particularly at wood-cement of 1:2.5 and above.

Low-Quality Structural and Interaction Data Improves Binding Affinity Prediction via Random Forest.

Science.gov (United States)

Li, Hongjian; Leung, Kwong-Sak; Wong, Man-Hon; Ballester, Pedro J

2015-06-12

Docking scoring functions can be used to predict the strength of protein-ligand binding. It is widely believed that training a scoring function with low-quality data is detrimental for its predictive performance. Nevertheless, there is a surprising lack of systematic validation experiments in support of this hypothesis. In this study, we investigated to which extent training a scoring function with data containing low-quality structural and binding data is detrimental for predictive performance. We actually found that low-quality data is not only non-detrimental, but beneficial for the predictive performance of machine-learning scoring functions, though the improvement is less important than that coming from high-quality data. Furthermore, we observed that classical scoring functions are not able to effectively exploit data beyond an early threshold, regardless of its quality. This demonstrates that exploiting a larger data volume is more important for the performance of machine-learning scoring functions than restricting to a smaller set of higher data quality.

Neural Network-Based Resistance Spot Welding Control and Quality Prediction

Energy Technology Data Exchange (ETDEWEB)

Allen, J.D., Jr.; Ivezic, N.D.; Zacharia, T.

1999-07-10

This paper describes the development and evaluation of neural network-based systems for industrial resistance spot welding process control and weld quality assessment. The developed systems utilize recurrent neural networks for process control and both recurrent networks and static networks for quality prediction. The first section describes a system capable of both welding process control and real-time weld quality assessment, The second describes the development and evaluation of a static neural network-based weld quality assessment system that relied on experimental design to limit the influence of environmental variability. Relevant data analysis methods are also discussed. The weld classifier resulting from the analysis successfldly balances predictive power and simplicity of interpretation. The results presented for both systems demonstrate clearly that neural networks can be employed to address two significant problems common to the resistance spot welding industry, control of the process itself, and non-destructive determination of resulting weld quality.

The central role of wood biology in understanding the durability of wood-coating interactions

Science.gov (United States)

Alex C. Wiedenhoeft

2007-01-01

To design effectively for durability, one must actively and honestly assess the material properties and limitations of each of the components in the design system; wood or wood composite, and the coating. Inasmuch as wood coatings are manufactured to specified tolerances from known materials, we have control of that component of the system. Compared to manmade...

Strength and Reliability of Wood for the Components of Low-cost Wind Turbines: Computational and Experimental Analysis and Applications

DEFF Research Database (Denmark)

Mishnaevsky, Leon; Freere, Peter; Sharma, Ranjan

2009-01-01

of experiments and computational investigations. Low cost testing machines have been designed, and employed for the systematic analysis of different sorts of Nepali wood, to be used for the wind turbine construction. At the same time, computational micromechanical models of deformation and strength of wood......This paper reports the latest results of the comprehensive program of experimental and computational analysis of strength and reliability of wooden parts of low cost wind turbines. The possibilities of prediction of strength and reliability of different types of wood are studied in the series...... are developed, which should provide the basis for microstructure-based correlating of observable and service properties of wood. Some correlations between microstructure, strength and service properties of wood have been established....

Microbial Communities in Sunken Wood Are Structured by Wood-Boring Bivalves and Location in a Submarine Canyon

Science.gov (United States)

Fagervold, Sonja K.; Romano, Chiara; Kalenitchenko, Dimitri; Borowski, Christian; Nunes-Jorge, Amandine; Martin, Daniel; Galand, Pierre E.

2014-01-01

The cornerstones of sunken wood ecosystems are microorganisms involved in cellulose degradation. These can either be free-living microorganisms in the wood matrix or symbiotic bacteria associated with wood-boring bivalves such as emblematic species of Xylophaga, the most common deep-sea woodborer. Here we use experimentally submerged pine wood, placed in and outside the Mediterranean submarine Blanes Canyon, to compare the microbial communities on the wood, in fecal pellets of Xylophaga spp. and associated with the gills of these animals. Analyses based on tag pyrosequencing of the 16S rRNA bacterial gene showed that sunken wood contained three distinct microbial communities. Wood and pellet communities were different from each other suggesting that Xylophaga spp. create new microbial niches by excreting fecal pellets into their burrows. In turn, gills of Xylophaga spp. contain potential bacterial symbionts, as illustrated by the presence of sequences closely related to symbiotic bacteria found in other wood eating marine invertebrates. Finally, we found that sunken wood communities inside the canyon were different and more diverse than the ones outside the canyon. This finding extends to the microbial world the view that submarine canyons are sites of diverse marine life. PMID:24805961

Evaluation of leachate quality from pentachlorophenol, creosote and ACA [ammoniacal chromium arsenate] preserved wood products

International Nuclear Information System (INIS)

Whiticar, D.M.; Letourneau, L.; Konasewich, D.

1994-01-01

A field study was conducted to evaluate the leachability characteristics of pentachlorophenol (PCP), creosote, and ammoniacal chromium arsenate (ACA) wood preservatives from freshly treated wood products. Test products included PCP-treated utility poles, creosote-treated timbers and marine pilings, and ACA-treated utility poles. Bundles of test products were placed over collection trays to collect the leachate generated by natural rainfall and by sprinkling with tap water. The sampling schedule was based on accumulated rainfall with samples taken at about every 15 mm from 15 mm to 150 mm. Analyses included pH, oil and grease, total organic carbon, ammonia, metals, polynuclear aromatic hydrocarbons (PAH), chlorinated and nonchlorinated phenols, resin acids, and fish toxicity. The study indicated that leachates from wood products freshly treated with ACA, creosote, and PCP have potential for aquatic toxicity if released to the environment. A decreasing trend was noted in both the arsenic and copper releases as cumulative precipitation increased. PCP releases remained constant over the course of the study while PAH releases showed no significant trend. Phenanthrene was found to be the main component in the releases. 28 refs., 18 figs., 7 tabs

Application of molecular genetic methods for identification of wood-decaying fungi in wood constructions

Directory of Open Access Journals (Sweden)

Elena Bobeková

2008-01-01

Full Text Available The aim of the paper is to evaluate the utilization of molecular biology methods for detection of wood decaying fungi directly from decomposed wood using a commercial DNA extraction kit developed for soil substrates (PowerSoil™ DNA isolation kit. The experiment based on dry rot fungus (Serpula lacrymans detection from inoculated wooden pieces under laboratory conditions was followed by field detection of wood-decaying fungi from wood structures on building constructions. Fungal DNA was identified using the PCR–based methods including species-specific PCR and sequencing of amplified ITS region of ribosomal DNA.

FLEXURAL TESTING OF WOOD-CONCRETE COMPOSITE BEAM MADE FROM KAMPER AND BANGKIRAI WOOD

Directory of Open Access Journals (Sweden)

Fengky Satria Yoresta

2015-07-01

Full Text Available Certain wood has a tensile strength that almost equal with steel rebar in reinforced concrete beams. This research aims to understand the capacity and flexural behavior of concrete beams reinforced by wood (wood-concrete composite beam. Two different types of beams based on placement positions of wood layers are proposed in this study. Two kinds of wood used are consisted of Bangkirai (Shorea laevifolia and Kamper (Cinnamomum camphora, meanwhile the concrete mix ratio for all beams is 1 cement : 2 fine aggregates : 3 coarse aggregates. Bending test is conducted by using one-point loading method. The results show that composite beam using Bangkirai wood is stronger than beams using Kamper wood. More thicker wood layer in tensile area will increase the flexural strength of beams. Crack patterns identified could be classified into flexural cracks, shear cracks, and split on wood layer   Beberapa jenis kayu tertentu memiliki kekuatan tarik yang hampir sama dengan tulangan baja pada balok beton bertulang. Penelitian ini bertujuan memahami kapasitas dan perilaku lentur balok beton bertulang yang diperkuat menggunakan kayu (balok komposit beton-kayu. Dua tipe balok yang berbeda berdasarkan posisi penempatan kayu digunakan dalam penelitian ini. Dua jenis kayu yang digunakan adalah kayu Bangkirai (Shorea laevifolia and Kamper (Cinnamomum camphora, sementara itu rasio campuran beton untuk semua balok menggunakan perbandingan 1 semen : 2 agregat halus : 3 agregat kasar. Pengujian lentur dilakukan menggunakan metode one-point loading. Hasil penelitian menunjukkan bahwa balok komposit dengan kayu Bangkirai lebih kuat dibandingkan balok dengan kayu Kamper. Semakin tebal lapisan kayu yang berada di daerah tarik akan meningkatkan kekuatan lentur balok. Pola kerusakan yang teridentifikasi dapat diklasifikasikan menjadi retak lentur, retak geser, dan pecah pada kayu REFERENCES Boen T. (2010. Retrofitting Simple Buildings Damaged by Earthquakes. World Seismic

The case for wood-fuelled heating

International Nuclear Information System (INIS)

Bent, Ewan

2001-01-01

This article looks at the wood heating industry in the UK and examines the heat market and the growth potential in the domestic, public, agricultural and commercial sectors. The current status of wood-fueled heating technology is considered, along with log and chip boilers, and the use of pellet fuel. The economics of wood-fuelled heating, the higher level of utilisation of wood-fuelled heating by utilities in northern European countries compared with the UK, and the barriers to the exploitation of wood fuelled heating are examined

Bacterial community succession in pine-wood decomposition

Directory of Open Access Journals (Sweden)

Anna eKielak

2016-03-01

Full Text Available Though bacteria and fungi are common inhabitants of decaying wood, little is known about the relationship between bacterial and fungal community dynamics during natural wood decay. Based on previous studies involving inoculated wood blocks, strong fungal selection on bacteria abundance and community composition was expected to occur during natural wood decay. Here we focused on bacterial and fungal community compositions in pine wood samples collected from dead trees in different stages of decomposition. We showed that bacterial communities undergo less drastic changes than fungal communities during wood decay. Furthermore, we found that bacterial community assembly was a stochastic process at initial stage of wood decay and became more deterministic in later stages, likely due to environmental factors. Moreover, composition of bacterial communities did not respond to the changes in the major fungal species present in the wood but rather to the stage of decay reflected by the wood density. We concluded that the shifts in the bacterial communities were a result of the changes in wood properties during decomposition and largely independent of the composition of the wood-decaying fungal communities.

Macrophotographic wood atlas of Annonaceae.

NARCIS (Netherlands)

Koek-Noorman, J.; Westra, L.I.T.

2012-01-01

In this article, a general description of the microscopic wood anatomy of Annonaceae is given. We provide a description of the wood anatomical features of the family and of all subfamilies and tribes, all from material in the Utrecht Wood collection. Hand-lens images can be an important help in

The challenge of bonding treated wood

Science.gov (United States)

Charles R. Frihart

2004-01-01

Wood products are quite durable if exposure to moisture is minimized; however, most uses of wood involve considerable exposure to moisture. To preserve the wood, chemicals are used to minimize moisture pickup, to prevent insect attack, and/or to resist microbial growth. The chemicals used as preservatives can interfere with adhesive bonds to wood. Given the many...

FIRE INSURANCE AND WOOD SCHOOL BUILDINGS.

Science.gov (United States)

PURCELL, FRANK X.

A COMPARISON OF FIRE INSURANCE COSTS OF WOOD, MASONRY, STEEL AND CONCRETE STRUCTURES SHOWS FIRE INSURANCE PREMIMUMS ON WOOD STRUCTURES TEND TO BE HIGHER THAN PREMIUMS ON MASONRY, STEEL AND CONCRETE BUILDINGS, HOWEVER, THE INITIAL COST OF THE WOOD BUILDINGS IS LOWER. DATA SHOW THAT THE SAVINGS ACHIEVED IN THE INITIAL COST OF WOOD STRUCTURES OFFSET…

Physical and mechanical properties of bio-composites from wood particles and liquefied wood resin

Science.gov (United States)

Hui Pan; Todd F. Shupe; Chung-Yun Hse

2009-01-01

Compression molded composites were made from wood particles and a liquefied wood/phenol/formaldehyde co-condensed resin. Based on our previous research, a phenol to wood (P/W) ratio of 2/1 was chosen for this study. The two experimental variables selected were: 1) liquefaction temperature (150o and 180oC) and 2) cooking method (atmospheric and sealed). Panels were...

Review of wood fuel from early thinning and plantation cleaning in the Netherlands

International Nuclear Information System (INIS)

Gelder, A. de

1998-01-01

Discussions regarding the use of wood fuels for commercial energy production in the Netherlands began in the 1990's. The main reasons for using wood fuel are: the political demand for using renewable energy, the need to reduce CO 2 emissions, and the lack of markets for surplus timber. Only 10 % of the area of Holland is forested. Therefore, early thinning and cleaning are important management tools for improving growth and producing better quality timber. The energy potential from early thinning and plantation cleaning could be between 400 000 and 570 000 dry tons annually. The Netherlands has not experience in harvesting energy wood. However, through the International Energy Agency/Bioenergy Agreement, knowledge gained in other countries, especially Denmark, Sweden and Finland, is being transferred to Holland. In 1996, there have been made field tests with Danish equipment. Although there are few technical barriers to wood fuel in the Netherlands, the economics of wood fuels consumption are affected by the low costs of fossil fuels and the high natural gas reserves. This is changing however, due to political concerns over the balance of greenhouse gases. In 1996, a small energy tax on fossil fuels was introduced and electricity suppliers are now selling an environmentally friendly 'green electricity'. Energy wood has a future in the Netherlands, although the total forest reserves would satisfy only a small percentage of energy requirements 5 refs

Arctic Bowyery – The Use of Compression Wood in Bows in the Subarctic and Arctic Regions of Eurasia and America

Directory of Open Access Journals (Sweden)

Marcus Lepola

2015-06-01

Full Text Available This paper is a study of the traditional use of a special kind of wood in bow construction in Eurasia and North America. This special kind of wood, called compression wood and coming from coniferous trees, has unique qualities that makes it suitable for bow construction. Bows made using this special wood have been referred to as Finno-Ugric bows, Sámi bows, Two-Wood bows and Eurasia laminated bows. These bows appear to have developed from archaic forms of compression wood self bows that were made from a single piece of wood. Recently features similar to the Eurasian compression wood bows have been discovered in bows originating from Alaska, and the use of compression wood for bow manufacture has been known to some Canadian Inuit groups. This paper addresses the origin and possible diffusion pattern of this innovation in bow technology in Eurasia and suggests a timeframe and a possible source for the transfer of this knowledge to North America. This paper also discusses the role of the Asiatic composite bow in the development of bows in Eurasia.

At-line validation of a process analytical technology approach for quality control of melamine-urea-formaldehyde resin in composite wood-panel production using near infrared spectroscopy.

Science.gov (United States)

Meder, Roger; Stahl, Wolfgang; Warburton, Paul; Woolley, Sam; Earnshaw, Scott; Haselhofer, Klaus; van Langenberg, Ken; Ebdon, Nick; Mulder, Roger

2017-01-01

The reactivity of melamine-urea-formaldehyde resins is of key importance in the manufacture of engineered wood products such as medium density fibreboard (MDF) and other wood composite products. Often the MDF manufacturing plant has little available information on the resin reactivity other than details of the resin specification at the time of batch manufacture, which often occurs off-site at a third-party resin plant. Often too, fresh resin on delivery at the MDF plant is mixed with variable volume of aged resin in storage tanks, thereby rendering any specification of the fresh resin batch obsolete. It is therefore highly desirable to develop a real-time, at-line or on-line, process analytical technology to monitor the quality of the resin prior to MDF panel manufacture. Near infrared (NIR) spectroscopy has been calibrated against standard quality methods and against 13 C nuclear magnetic resonance (NMR) measures of molecular composition in order to provide at-line process analytical technology (PAT), to monitor the resin quality, particularly the formaldehyde content of the resin. At-line determination of formaldehyde content in the resin was made possible using a six-factor calibration with an R 2 (cal) value of 0.973, and R 2 (CV) value of 0.929 and a root-mean-square error of cross-validation of 0.01. This calibration was then used to generate control charts of formaldehyde content at regular four-hourly periods during MDF panel manufacture in a commercial MDF manufacturing plant.

Assessment and prediction of speech quality in telecommunications

CERN Document Server

Möller, Sebastian

2000-01-01

The quality of a telecommunication voice service is largely inftuenced by the quality of the transmission system. Nevertheless, the analysis, synthesis and prediction of quality should take into account its multidimensional aspects. Quality can be regarded as a point where the perceived characteristics and the desired or expected ones meet. A schematic is presented which classifies different entities which contribute to the quality of a service, taking into account conversational, user as weIl as service related contributions. Starting from this concept, perceptively relevant constituents of speech communication quality are identified. The perceptive factors result from ele­ ments of the transmission configuration. A simulation model is developed and implemented which allows the most relevant parameters of traditional trans­ mission configurations to be manipulated, in real time and for the conversation situation. Inputs into the simulation are instrumentally measurable quality elements commonly used in tra...

Impact of Indoor Use of Wood on the Quality of Interior Ambiances under Overcast and Clear Skies: Case Study of the Eugene H. Kruger Building, Québec City

Directory of Open Access Journals (Sweden)

Hoda Jafarian

2016-01-01

Full Text Available This paper explores the potential of wood for improving environmental quality in interior spaces. In northern climate cities where overcast skies predominate, interior spaces may appear gloomy or dull, since natural light is white and uniform. Nevertheless it is observed that wooden surfaces tend to create warmer and brighter spaces under overcast sky conditions. The objectives of this research were twofold. The first was evaluating the quality of wooden spaces under two sky conditions in terms of color, brightness and contrast. The second objective was to investigate daylight quantity of wooden spaces under diffuse and clear sky conditions. The method involved on site-surveys using Photolux, a calibrated photoluminance meter. Data consist of calibrated digital images that were processed to analyze the quality of spaces based on brightness, contrast, and color. The Kruger Building, with its internal wooden architectural structure and decorative indoor panels, was chosen as a site study for this research. Conclusions suggest that knowing the effect of different sky conditions on wooden spaces can help architects and other professionals in designing more comfortable and efficient ambiances. More particularly, this research addresses issues related to the quantitative effects of wood on daylighting distribution, visual comfort and luminance diversity.

The wood energy in France

International Nuclear Information System (INIS)

Douard, F.; Oremus, Y.; Garsault-Fabbi, A.

2007-01-01

The program law fixing the energy policy (POPE Law of the 13 july 2005) fixes an objective of 50% of growth for the renewable heat. As this renewable heat is today generated by the biomass, it seems necessary to adjust all the efforts on this sector. This document proposes to takes stock on the wood energy in France. It presents the wood fuels, an evaluation of the Wood-Energy Plan decided by the ADEME in 2000, the wood heat networks, and some example of installations. (A.L.B.)

An assessment of management practices of wood and wood-related wastes in the urban environment

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

The US Environmental Protection Agency estimates that yard waste{sup 1} accounts for approximately 16% of the municipal solid waste (MSW) stream (US EPA, 1994). Until recently, specific data and related information on this component of the (MSW) stream has been limited. The purposes of this study, phase two of the three-phase assessment of urban wood waste issues, are to assess and describe current alternatives to landfills for urban wood waste management; provide guidance on the management of urban wood waste to organizations that produce or manage wood waste; and clarify state regulatory and policy positions affecting these organizations. For this study, urban wood waste is defined as solid waste generated by tree and landscape maintenance services (public and private). Urban wood waste includes the following materials: unchipped mixed wood, unchipped logs, and unchipped tops and brush; clearing and grubbing waste; fall leaves and grass clippings; and chips and whole stumps. Construction and demolition debris and consumer-generated yard waste are not included in this study. Generators of urban wood waste include various organizations; municipal, county, and commercial tree care divisions; nurseries, orchards, and golf courses; municipal park and recreation departments; and electric and telephone utility power line maintenance, excavator and land clearance, and landscape organizations. (1) US EPA defines yard waste as ''yard trimmings'' which includes ''grass, leaves and tree brush trimmings from residential, institutional, and commercial sources.''

Complex geometries in wood

DEFF Research Database (Denmark)

Tamke, Martin; Ramsgaard Thomsen, Mette; Riiber Nielsen, Jacob

2009-01-01

The versatility of wood constructions and traditional wood joints for the production of non standard elements was in focus of a design based research. Herein we established a seamless process from digital design to fabrication. A first research phase centered on the development of a robust...... parametric model and a generic design language a later explored the possibilities to construct complex shaped geometries with self registering joints on modern wood crafting machines. The research was carried out as collaboration with industrial partners....

Uncertainty estimation and risk prediction in air quality

International Nuclear Information System (INIS)

Garaud, Damien

2011-01-01

This work is about uncertainty estimation and risk prediction in air quality. Firstly, we build a multi-model ensemble of air quality simulations which can take into account all uncertainty sources related to air quality modeling. Ensembles of photochemical simulations at continental and regional scales are automatically generated. Then, these ensemble are calibrated with a combinatorial optimization method. It selects a sub-ensemble which is representative of uncertainty or shows good resolution and reliability for probabilistic forecasting. This work shows that it is possible to estimate and forecast uncertainty fields related to ozone and nitrogen dioxide concentrations or to improve the reliability of threshold exceedance predictions. The approach is compared with Monte Carlo simulations, calibrated or not. The Monte Carlo approach appears to be less representative of the uncertainties than the multi-model approach. Finally, we quantify the observational error, the representativeness error and the modeling errors. The work is applied to the impact of thermal power plants, in order to quantify the uncertainty on the impact estimates. (author) [fr

A new genomic resource dedicated to wood formation in Eucalyptus

Directory of Open Access Journals (Sweden)

Couloux Arnaud

2009-03-01

Full Text Available Abstract Background Renowned for their fast growth, valuable wood properties and wide adaptability, Eucalyptus species are amongst the most planted hardwoods in the world, yet they are still at the early stages of domestication because conventional breeding is slow and costly. Thus, there is huge potential for marker-assisted breeding programs to improve traits such as wood properties. To this end, the sequencing, analysis and annotation of a large collection of expressed sequences tags (ESTs from genes involved in wood formation in Eucalyptus would provide a valuable resource. Results We report here the normalization and sequencing of a cDNA library from developing Eucalyptus secondary xylem, as well as the construction and sequencing of two subtractive libraries (juvenile versus mature wood and vice versa. A total of 9,222 high quality sequences were collected from about 10,000 cDNA clones. The EST assembly generated a set of 3,857 wood-related unigenes including 2,461 contigs (Cg and 1,396 singletons (Sg that we named 'EUCAWOOD'. About 65% of the EUCAWOOD sequences produced matches with poplar, grapevine, Arabidopsis and rice protein sequence databases. BlastX searches of the Uniref100 protein database allowed us to allocate gene ontology (GO and protein family terms to the EUCAWOOD unigenes. This annotation of the EUCAWOOD set revealed key functional categories involved in xylogenesis. For instance, 422 sequences matched various gene families involved in biosynthesis and assembly of primary and secondary cell walls. Interestingly, 141 sequences were annotated as transcription factors, some of them being orthologs of regulators known to be involved in xylogenesis. The EUCAWOOD dataset was also mined for genomic simple sequence repeat markers, yielding a total of 639 putative microsatellites. Finally, a publicly accessible database was created, supporting multiple queries on the EUCAWOOD dataset. Conclusion In this work, we have identified a

A local isotropic/global orthotropic finite element technique for modeling the crush of wood in impact limiters

International Nuclear Information System (INIS)

Attaway, S.W.; Yoshimura, H.R.

1989-01-01

Wood is often used as the energy absorbing material in impact limiters, because it begins to crush at low strains, then maintains a near constant crush stress up to nearly 60% volume reduction, and then locks up. Hill (Hill and Joseph, 1974) has performed tests that show that wood is an excellent absorber. However, wood's orthotropic behavior for large crush is difficult to model. In the past, analysts have used isotropic foam-like material models for modeling wood. A new finite element technique is presented in this paper that gives a better model of wood crush than the model currently in use. The orthotropic technique is based on locally isotropic, but globally orthotropic (LIGO) (Attaway, 1988) assumptions in which alternating layers of hard and soft crushable material are used. Each layer is isotropic; however, by alternating hard and soft thin layers, the resulting global behavior is orthotropic. In the remainder of this paper, the new technique for modeling orthotropic wood crush will be presented. The model is used to predict the crush behavior for different grain orientations of balsa wood. As an example problem, an impact limiter containing balsa wood as the crushable material is analyzed using both an isotropic model and the LIGO model

Tracing nitrogen accumulation in decaying wood and examining its impact on wood decomposition rate

Science.gov (United States)

Rinne, Katja T.; Rajala, Tiina; Peltoniemi, Krista; Chen, Janet; Smolander, Aino; Mäkipää, Raisa

2016-04-01

Decomposition of dead wood, which is controlled primarily by fungi is important for ecosystem carbon cycle and has potentially a significant role in nitrogen fixation via diazotrophs. Nitrogen content has been found to increase with advancing wood decay in several studies; however, the importance of this increase to decay rate and the sources of external nitrogen remain unclear. Improved knowledge of the temporal dynamics of wood decomposition rate and nitrogen accumulation in wood as well as the drivers of the two processes would be important for carbon and nitrogen models dealing with ecosystem responses to climate change. To tackle these questions we applied several analytical methods on Norway spruce logs from Lapinjärvi, Finland. We incubated wood samples (density classes from I to V, n=49) in different temperatures (from 8.5oC to 41oC, n=7). After a common seven day pre-incubation period at 14.5oC, the bottles were incubated six days in their designated temperature prior to CO2 flux measurements with GC to determine the decomposition rate. N2 fixation was measured with acetylene reduction assay after further 48 hour incubation. In addition, fungal DNA, (MiSeq Illumina) δ15N and N% composition of wood for samples incubated at 14.5oC were determined. Radiocarbon method was applied to obtain age distribution for the density classes. The asymbiotic N2 fixation rate was clearly dependent on the stage of wood decay and increased from stage I to stage IV but was substantially reduced in stage V. CO2 production was highest in the intermediate decay stage (classes II-IV). Both N2 fixation and CO2 production were highly temperature sensitive having optima in temperature 25oC and 31oC, respectively. We calculated the variation of annual levels of respiration and N2 fixation per hectare for the study site, and used the latter data together with the 14C results to determine the amount of N2 accumulated in wood in time. The proportion of total nitrogen in wood

How to make a beetle out of wood: multi-elemental stoichiometry of wood decay, xylophagy and fungivory.

Science.gov (United States)

Filipiak, Michał; Weiner, January

2014-01-01

The majority of terrestrial biomass is wood, but the elemental composition of its potential consumers, xylophages, differs hugely from that of wood. This causes a severe nutritional imbalance. We studied the stoichiometric relationships of 11 elements (C, N, P, K, Ca, Mg, Fe, Zn, Mn, Cu, Na) in three species of pine-xylem-feeding insects, Stictoleptura rubra, Arhopalus rusticus (Coleoptera, Cerambycidae) and Chalcophora mariana (Coleoptera, Buprestidae), to elucidate their mechanisms of tissue growth and to match their life histories to their dietary constraints. These beetles do not differ from other Coleoptera in their absolute elemental compositions, which are approximately 1000 (N), 100 (P, Cu) and 50 (K, Na) times higher than in dead but undecayed pine wood. This discrepancy diminishes along the wood decay gradient, but the elemental concentrations remain higher by an order of magnitude in beetles than in highly decayed wood. Numerical simulation of the life history of S. rubra shows that feeding on nutrient-poor undecayed wood would extend its development time to implausible values, whereas feeding on highly decomposed wood (heavily infected with fungi) would barely balance its nutritional budget during the long development period of this species. The changes in stoichiometry indicate that the relative change in the nutrient levels in decaying wood cannot be attributed solely to carbon loss resulting from decomposer respiration: the action of fungi substantially enriches the decaying wood with nutritional elements imported from the outside of the system, making it a suitable food for wood-eating invertebrates.

A new air quality monitoring and early warning system: Air quality assessment and air pollutant concentration prediction.

Science.gov (United States)

Yang, Zhongshan; Wang, Jian

2017-10-01

Air pollution in many countries is worsening with industrialization and urbanization, resulting in climate change and affecting people's health, thus, making the work of policymakers more difficult. It is therefore both urgent and necessary to establish amore scientific air quality monitoring and early warning system to evaluate the degree of air pollution objectively, and predict pollutant concentrations accurately. However, the integration of air quality assessment and air pollutant concentration prediction to establish an air quality system is not common. In this paper, we propose a new air quality monitoring and early warning system, including an assessment module and forecasting module. In the air quality assessment module, fuzzy comprehensive evaluation is used to determine the main pollutants and evaluate the degree of air pollution more scientifically. In the air pollutant concentration prediction module, a novel hybridization model combining complementary ensemble empirical mode decomposition, a modified cuckoo search and differential evolution algorithm, and an Elman neural network, is proposed to improve the forecasting accuracy of six main air pollutant concentrations. To verify the effectiveness of this system, pollutant data for two cities in China are used. The result of the fuzzy comprehensive evaluation shows that the major air pollutants in Xi'an and Jinan are PM 10 and PM 2.5 respectively, and that the air quality of Xi'an is better than that of Jinan. The forecasting results indicate that the proposed hybrid model is remarkably superior to all benchmark models on account of its higher prediction accuracy and stability. Copyright © 2017 Elsevier Inc. All rights reserved.

Photodegradation of wood and depth profile analysis

International Nuclear Information System (INIS)

Kataoka, Y.

2008-01-01

Photochemical degradation is a key process of the weathering that occurs when wood is exposed outdoors. It is also a major cause of the discoloration of wood in indoor applications. The effects of sunlight on the chemical composition of wood are superficial in nature, but estimates of the depth at which photodegradation occurs in wood vary greatly from 80 microm to as much as 2540 mic rom. Better understanding of the photodegradation of wood through depth profile analysis is desirable because it would allow the development of more effective photo-protective treatments that target the surface layers of wood most susceptible to photodegradation. This paper briefly describes fundamental aspects of photodegradation of wood and reviews progress made in the field of depth profile study on the photodegradation of wood. (author)

Factors affecting the laser processing of wood, 2: Effects of material parameters on machinability

International Nuclear Information System (INIS)

Arai, T.; Hayashi, D.

1994-01-01

Material parameters of wood were investigated. Factors relating to the workpiece include cutting direction, specific gravity, and components of the wood such as resin-like materials. Also studies of the effects of irregular tissue on machinability were made. The interactions between laser beam and materials are often greatly complex. They depend on the characteristics of the laser beam, the thermal constants of the woods, and the optical surface properties of the woods. Therefore, high quality beam mode and carefully selected materials were used. The following laser cutting properties became clear after studying the experimental results. Slow speed cutting and softwoods make slight differences, regarding cutting section and fiber direction. However, it can beconsidered that there is not very much change except in cross-section. Because of the high power density of laser, cutting speed makes no big difference. The irregular tissue of wood cannot maintain normal cutting speed and accuracy. The factor of genuine density eta, which is thought to be entirely independent of each specific gravity, is definedas the concept of density in general. It can be obtained by applying a simple rule, that is, the eta is the ratio of r(u)/rho(s) where rho(s) is the wood substance as the characteristic value of wood, and r(u)is specific gravity. An experimental formula shows that the depth of cut decreases in proportion to the value of eta. However, in the strict sense of the word, data of wood material as a natural resources mustbe treated qualitatively, because there are deviations from regularity due to various reasons. (author)

Solutions for wood-based bio-energy price discovery

Energy Technology Data Exchange (ETDEWEB)

Teraes, Timo [FOEX Indexes Ltd., Helsinki (Finland)], e-mail: timo@foex.fi

2012-11-01

Energy prices are highly volatile. This volatility can have serious ill-effects on the profitability of companies engaged in the energy business. There are, however, a number of price risk management tools which can be used to reduce the problems caused by price volatility. International trade of wood pellets and wood chips is rapidly growing. A good price transparency helps in developing the trade further. In order to meet the renewable energy targets within the EU, further growth of volumes is needed, at least within Europe and from overseas supply sources to the European markets. Reliable price indices are a central element in price risk management and in general price discovery. Exchanges have provided, in the past, the most widely known price discovery systems. Since 1990's, an increasing number of price risk management tools has been based on cash settlement concept. Cash settlement requires high quality benchmark price indices. These have been developed by the exchanges themselves, by trade press and by independent price benchmark provider companies. The best known of these benchmarks in forest industry and now also in wood-based bioenergy products are the PIX indices, provided by FOEX Indexes Ltd. This presentation discusses the key requirements for a good price index and the different ways of using the indices. Price relationships between wood chip prices and pellet prices are also discussed as will be the outlook for the future volume growth and trade flows in woodchips and pellets mainly from the European perspective.

RELATIONSHIPS BETWEEN ANATOMICAL FEATURES AND INTRA-RING WOOD DENSITY PROFILES IN Gmelina arborea APPLYING X-RAY DENSITOMETRY

Directory of Open Access Journals (Sweden)

Mario Tomazelo-Filho

2007-12-01

Full Text Available Four annual tree-rings (2 of juvenile wood and 2 of mature wood were sampled from fast-growth plantations ofGmelina arborea in two climatic conditions (dry and wet tropical in Costa Rica. Each annual tree-ring was divided in equal parts ina radial direction. For each part, X-ray density as well as vessel percentage, length and width fiber, cell wall thickness and lumendiameter were measured. Wood density and profile patterns of cell dimension demonstrated inconsistency between juvenile andmature wood and climatic conditions. The Pearson correlation matrix showed that intra-ring wood density was positively correlatedwith the cell wall thickness and negatively correlated with vessel percentage, fiber length, lumen diameter and width. The forwardstepwise regressions determined that: (i intra-ring wood density variation could be predicted from 76 to 96% for anatomicalvariation; (ii cell wall thickness was the most important anatomical feature to produce intra-ring wood density variation and (iii thevessel percentage, fiber length, lumen diameter and width were the second most statically significant characteristics to intra-ring wooddensity, however, with low participation of the determination coefficient of stepwise regressions.

Robert Williams Wood: pioneer of invisible light.

Science.gov (United States)

Sharma, Shruti; Sharma, Amit

2016-03-01

The Wood's lamp aids in the diagnosis of multiple infectious, inflammatory and neoplastic dermatologic conditions. Although the Wood's lamp has many applications, which have improved both the diagnosis and management of disease, the man credited for its invention is relatively unknown in medicine. Robert Williams Wood, a prominent physicist of the early 20th century, is credited for the invention of the Wood's lamp. Wood was the father of infrared and ultraviolet photography and made significant contributions to other areas in optics and spectroscopy. Wood's work encompassed the formative years of American Physics; he published over 200 original papers over his lifetime. A few years after the invention of the Wood's lamp for ultraviolet photography, physicians in Europe adopted the Wood's lamp for dermatologic applications. Wood's lamp remains popular in clinics globally, given its ease of use and ability to improve diagnostic precision. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Wood Specific Gravity Variations and Biomass of Central African Tree Species: The Simple Choice of the Outer Wood.

Directory of Open Access Journals (Sweden)

Jean-François Bastin

Full Text Available Wood specific gravity is a key element in tropical forest ecology. It integrates many aspects of tree mechanical properties and functioning and is an important predictor of tree biomass. Wood specific gravity varies widely among and within species and also within individual trees. Notably, contrasted patterns of radial variation of wood specific gravity have been demonstrated and related to regeneration guilds (light demanding vs. shade-bearing. However, although being repeatedly invoked as a potential source of error when estimating the biomass of trees, both intraspecific and radial variations remain little studied. In this study we characterized detailed pith-to-bark wood specific gravity profiles among contrasted species prominently contributing to the biomass of the forest, i.e., the dominant species, and we quantified the consequences of such variations on the biomass.Radial profiles of wood density at 8% moisture content were compiled for 14 dominant species in the Democratic Republic of Congo, adapting a unique 3D X-ray scanning technique at very high spatial resolution on core samples. Mean wood density estimates were validated by water displacement measurements. Wood density profiles were converted to wood specific gravity and linear mixed models were used to decompose the radial variance. Potential errors in biomass estimation were assessed by comparing the biomass estimated from the wood specific gravity measured from pith-to-bark profiles, from global repositories, and from partial information (outer wood or inner wood.Wood specific gravity profiles from pith-to-bark presented positive, neutral and negative trends. Positive trends mainly characterized light-demanding species, increasing up to 1.8 g.cm-3 per meter for Piptadeniastrum africanum, and negative trends characterized shade-bearing species, decreasing up to 1 g.cm-3 per meter for Strombosia pustulata. The linear mixed model showed the greater part of wood specific gravity

Wood Specific Gravity Variations and Biomass of Central African Tree Species: The Simple Choice of the Outer Wood.

Science.gov (United States)

Bastin, Jean-François; Fayolle, Adeline; Tarelkin, Yegor; Van den Bulcke, Jan; de Haulleville, Thales; Mortier, Frederic; Beeckman, Hans; Van Acker, Joris; Serckx, Adeline; Bogaert, Jan; De Cannière, Charles

2015-01-01

Wood specific gravity is a key element in tropical forest ecology. It integrates many aspects of tree mechanical properties and functioning and is an important predictor of tree biomass. Wood specific gravity varies widely among and within species and also within individual trees. Notably, contrasted patterns of radial variation of wood specific gravity have been demonstrated and related to regeneration guilds (light demanding vs. shade-bearing). However, although being repeatedly invoked as a potential source of error when estimating the biomass of trees, both intraspecific and radial variations remain little studied. In this study we characterized detailed pith-to-bark wood specific gravity profiles among contrasted species prominently contributing to the biomass of the forest, i.e., the dominant species, and we quantified the consequences of such variations on the biomass. Radial profiles of wood density at 8% moisture content were compiled for 14 dominant species in the Democratic Republic of Congo, adapting a unique 3D X-ray scanning technique at very high spatial resolution on core samples. Mean wood density estimates were validated by water displacement measurements. Wood density profiles were converted to wood specific gravity and linear mixed models were used to decompose the radial variance. Potential errors in biomass estimation were assessed by comparing the biomass estimated from the wood specific gravity measured from pith-to-bark profiles, from global repositories, and from partial information (outer wood or inner wood). Wood specific gravity profiles from pith-to-bark presented positive, neutral and negative trends. Positive trends mainly characterized light-demanding species, increasing up to 1.8 g.cm-3 per meter for Piptadeniastrum africanum, and negative trends characterized shade-bearing species, decreasing up to 1 g.cm-3 per meter for Strombosia pustulata. The linear mixed model showed the greater part of wood specific gravity variance was