40 CFR 180.254 - Carbofuran; tolerances for residues.

Science.gov (United States)

2010-07-01

...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances... than 1 ppm is carbamates) 2 12/31/09 Pumpkin (of which not more than 0.6 ppm is carbamates) 0.8 12/31...

Total and occluded residual gas content inside the nuclear fuel pellets

International Nuclear Information System (INIS)

Moura, Sergio C.; Fernandes, Carlos E.; Oliveira, Justine R.; Machado, Joyce F.; Guglielmo, Luisa M.; Bustillos, Oscar V.

2009-01-01

This work describes three techniques available to measure total and occluded residual gases inside the UO 2 nuclear fuel pellets. Hydrogen is the major gas compound inside these pellets, due to sintering fabrication process but Nitrogen is present as well, due to storage atmosphere fuel. The total and occluded residual gas content inside these pellets is a mandatory requirement in a quality control to assure the well function of the pellets inside the nuclear reactor. This work describes the Gas Extractor System coupled with mass spectrometry GES/MS, the Gas Extractor System coupled with gas chromatography GES/GC and the total Hydrogen / Nitrogen H/N analyzer as well. In the GES, occlude gases in the UO 2 pellets is determinate using a high temperature vacuum extraction system, in which the minimum limit of detection is in the range 0.002 cc/g. The qualitative and quantitative determination of the amount of gaseous components employs a mass spectrometry or a gas chromatography technique. The total Hydrogen / Nitrogen analyzer employ a thermal conductivity gas detector linked to a gaseous extractor furnace which has a detection limit is in the range 0.005 cc/g. The specification for the residual gas analyses in the nuclear fuel pellets is 0.03 cc/g, all techniques satisfy the requirement but not the nature of the gases due to reaction with the reactor cladding. The present work details the chemical reaction among Hydrogen / Nitrogen and nuclear reactor cladding. (author)

Biostimulation of soil polluted by 40000 ppm of waste motor oil and phytoremediation with Cicer arietinum and Burkholderia cepacia

Directory of Open Access Journals (Sweden)

Meza-Ramírez Janitzi Yunuén

2016-08-01

Full Text Available Soil polluted by 40000 ppm of waste residual oil (WRO, is a relative high hydrocarbons mix concentration according to Mexican regulation related with as the well know NOM-138-SEMARNAT/SSA1-2003 (NOM-138. Due to cause lost soil´s fertility, inhibiting microbial life and reducing vegetal production. To NOM-138 the highest limit of hydrocarbons mix allowed in soil is equal to 4400 ppm/kg. Aims of this research were: i Biostimulation of soil polluted by 40000 ppm of WRO by vermicompost and/or bovine compost, ii Phytoremediation by Cicer arietinum and Burkholderia cepacia to reduce WRO at below value compared to highest according to NOM-138. Results showed that biostimulation of soil with bovine compost eliminated WRO at 24000 ppm in 49 days. Then phytoremediation by C. arietinum and B. cepacia decreased WRO at 2760 ppm value below to compare to highest concentration allowed to NOM-138. It´s concluded that biore-mediation of soil impacted by relatively high concentration of WRO, the best strategy was to apply both biostimulation/phytoremediation that separate.

Reproduction, growth, and tissue residues of deer fed dieldrin

Science.gov (United States)

Murphy, D.A.; Korschgen, L.J.

1970-01-01

Feeding tests were conducted from January, 1966, to January, 1969, to ascertain the effects of daily ingestions of sublethal amounts of dieldrin on white-tailed deer (Odocoileus virginianus). Groups of deer on 0 ppm dieldrin (controls), 5 ppm, and 25 ppm dieldrin were maintained at these respective levels, as were their progeny. Treated food was readily accepted. Dieldrin intoxication was not observed, and 9 of 10 animals of each group survived 3 years of treatment. No differences in conception or in utero mortality were found between groups. Fawns from dieldrin-fed does were smaller at birth and greater post-partum mortality occurred. Fertility of male progeny was not affected. Growth was slower and remained reduced in dieldrin-treated females which were immature when the study began. Hematologic values and serum protein concentrations were not significantly (P > 0.05) related to treatment. Liver/body weight ratios were significantly (P brain, liver, and thigh muscle tissues showed no evidence of increasing with length of treatment, but showed definite relationships to levels of dieldrin in daily diets. Nursing fawns had higher residues in brain tissues than did older deer on 5 ppm a d 25 ppm dieldrin. Highest brain residues (12.60 and 12.10 ppm, wet weight) occurred in fawns only a few days of age at death. Equilibrium between ingestion and storage or excretion of dieldrin occurred prior to 200 days and continued until nearly 1,100 days. There was no evidence of a sharp decline in residues after a long period of continued dosage. Daily ingestion of 100 and 200 ppm of dieldrin proved fatal to yearling male deer at 27 and 22 days, respectively.

Endrin in birds: Lethal residues and secondary poisoning

Science.gov (United States)

Stickel, W.H.; Reichel, W.L.; Hughes, D.L.

1979-01-01

Endrin residues in brains that are diagnostic of death were determined for several species of birds. Residues of 0.8 ppm or more of endrin in brain meant death; 0.6 ppm or less meant survival; between was a zone of overlap. These criteria indicate that some wild birds of the U.S., particularly white pelicans in the Northwest and two bald eagles, have been killed by endrin. Signs of endrin poisoning in experimental birds are described. The important and highly toxic metabolite in rodents, 12-ketoendrin, was sought but not found.

PPM klystron operation in GLCTA

International Nuclear Information System (INIS)

Saeki, T.; Akemoto, M.; Shidara, T.

2004-01-01

High-gradient tests of X-band accelerator structure have been done with two solenoidal-type klystrons at Global Linear Collider Test Accelerator (GLCTA) facility in High Energy Accelerator Research Organization (KEK). In the GLCTA facility, a PPM-type klystron was installed and has been operated with dummy load from this April. In this article, the installation and the status of the PPM-type klystron operations are presented. (author)

Residue levels of polychlorobiphenyls,. sigma. DDT, and mercury in bird species commonly preyed upon by the peregrine falcon (Falco peregrinus Tunst. ) in Sweden

Energy Technology Data Exchange (ETDEWEB)

Lindberg, P.; Odsjoe, T.; Reutergardh, L.

1985-03-01

The levels of polychlorobiphenyls (PCBs), ..sigma..DDT, and total mercury were analyzed in samples of common prey species of the peregrine falcon in two falcon territories, one in northern and one in southern Sweden. Resident and herbivorous prey species showed low residue levels, while elevated levels were found in birds feeding on animals in aquatic habitats. According to biomass, waders accounted for most of the mercury and ..sigma..DDT in the diet of the northern falcons, while the black-headed gulls had this role in southern Sweden. During the breeding season, the peregrines in northern Sweden were exposed to significantly higher levels of ..sigma..DDT and Hg than the southern peregrines. The estimated average residue levels (based on breast muscles) in a diet were in northern Sweden 0.26 ppm ..sigma..DDT, 0.47 ppm PCB and 0.20 ppm Hg wet-weight. Corresponding figures for southern Sweden were 0.17 ppm ..sigma..DDT, 0.53 ppm PCB and 0.07 ppm Hg. The organochlorine levels in a sample of peregrine eggs were higher than expected from contaminant levels in the diet. It is possible that the main accumulation of pesticides occurs on wintering grounds in western Europe for the Fennoscandian peregrines.

Methylisothiazolinone testing at 2000 ppm: a prevalent sensitizer for allergic contact dermatitis.

Science.gov (United States)

Ham, Kaiya; Posso-De Los Rios, Claudia J; Gooderham, Melinda

2015-01-01

Methylchloroisothiazolinone (MCI) and methylisothiazolinone (MI) have been identified as potent allergens. The optimal MI concentration for patch testing for reaction to these agents has not yet been identified, but it has been suggested that testing MI at 2000 ppm may reduce false-negative reactions. The aim of this study was to report allergic reactions to MI and MCI/MI detected in a community dermatology practice setting in Ontario, Canada. The patch test records of patients with suspected allergic contact dermatitis seen between October 2007 and June 2014 were reviewed. We compared positive patch testing before and after December 2011 when a higher MI concentration was used (2000 ppm aqueous) in addition to the baseline series MCI/MI at 100 ppm. A total of 794 patient records were reviewed. There were 38 true-positive reactions to MI or MCI/MI. Of these 38 patients, 26 (68%) were female. We detected an overall increase in the rate of positive patch testing to MCI/MI, MI alone, or both from 3.13% to 7.45% when MI concentration was introduced at 2000 ppm aqueous. Occupational differences existed between sexes. The addition of MI at 2000 ppm to our screening series effectively increased the detection of MI-induced allergic contact dermatitis.

Eggshell thinning and residues in mallards on year after DDE exposure

Science.gov (United States)

Haegele, M.A.; Hudson, R.H.

1974-01-01

A group of 16 mallard hens (Anas platyrhynchos), that had been given feed containing 40 ppm ofp,p'-DDE for 96 days, laid eggs with shells averaging about 15%?20% thinner than those of ten control birds during and up to 42 days after treatment. In eight of the treated birds killed at that time, whole-body DDE residues averaged 33.1 ppm (wet weight). The other eight treated birds and ten controls were kept through the winter with no additional DDE exposure and penned separately five days for individual egg collection about three weeks after laying began in spring. At that time (nearly 11 months after DDE feeding had stopped), the treated birds laid eggs with shells averaging 7.4% thinner than control eggshells (significant at P<0.05) and their whole-body DDE residues averaged 9.6 ppm (wet weight). Variations in eggshell thickness and DDE residues were considerable among treated birds. However, regression analysis showed moderate negative correlations (r=?0.51 to ?0.62) between eggshell thickness and DDE residues in whole bodies and eggs, and strong positive correlations (r=0.73 and 0.91) between DDE residues in whole bodies and in eggs.

Decomposition of dilute residual active chlorine in sea-water

International Nuclear Information System (INIS)

Yoshinaga, Tetsutaro; Kawano, Kentaro; Yanagase, Kenjiro; Shiga, Akira

1985-01-01

Coastal industries such as power stations require enormous quantities of sea-water for cooling, but the marine organisms in it often result in fouling and/or blockade of the circulating water condenser and pipeworks. To prevent this, chlorine, or hypochlorite by the direct electrolysis of sea-water have been added. Environmental concerns, however, dictate that the residual chlorine concentration at the outlet should be less than the regulated value (0.02 ppm). Methods for decomposing dilute residual chlorine solutions were therefore studied. It was found that: 1) The addition of (raw) sea-water to the sea-water which passed through the condenser lowered the residual chlorine concentration to an greater extent than could be expected by dilution only. 2) Ozonation of the residual chlorine solution led to degradation of OCl - , but in solutions with a residual chlorine concentrations of less than 3 -- 4 ppm, ozonation had no effect. 3) Irradiation with ultra violet light (254 nm) decomposed the residual chlorine. Under the present work conditions (25 0 C: pH 8; depth 10 mm), nearly first order kinetics were to hold [da/dt = ksub((1)) (1-a)sup(n)]. There is a proportional relationship between the kinetic constant (k) and illuminous intensity (L), i.e., ksub((1))[C 0 sup(Cl 2 ): 10 ppm] = 6.56 x 10 -5 L (L = 0 -- 1000 lx). Thus, the use of both sea-water addition and UV irradiation provides a probable method for decomposing a residual chlorine to the expected concentration. (author)

LDPC-PPM Coding Scheme for Optical Communication

Science.gov (United States)

Barsoum, Maged; Moision, Bruce; Divsalar, Dariush; Fitz, Michael

2009-01-01

In a proposed coding-and-modulation/demodulation-and-decoding scheme for a free-space optical communication system, an error-correcting code of the low-density parity-check (LDPC) type would be concatenated with a modulation code that consists of a mapping of bits to pulse-position-modulation (PPM) symbols. Hence, the scheme is denoted LDPC-PPM. This scheme could be considered a competitor of a related prior scheme in which an outer convolutional error-correcting code is concatenated with an interleaving operation, a bit-accumulation operation, and a PPM inner code. Both the prior and present schemes can be characterized as serially concatenated pulse-position modulation (SCPPM) coding schemes. Figure 1 represents a free-space optical communication system based on either the present LDPC-PPM scheme or the prior SCPPM scheme. At the transmitting terminal, the original data (u) are processed by an encoder into blocks of bits (a), and the encoded data are mapped to PPM of an optical signal (c). For the purpose of design and analysis, the optical channel in which the PPM signal propagates is modeled as a Poisson point process. At the receiving terminal, the arriving optical signal (y) is demodulated to obtain an estimate (a^) of the coded data, which is then processed by a decoder to obtain an estimate (u^) of the original data.

Improving Project Portfolio Management (PPM) for Improvement Projects

DEFF Research Database (Denmark)

Pries-Heje, Jan; Jakobsen, Peter M.; Korsaa, Morten

2017-01-01

Project Portfolio Management (PPM) focus on the integration and alignment of projects with the business operation in order to achieve most value and cost-efficiency for the investment in projects. PPM is often a challenge and especially so for improvement projects where PPM is considerably...... of evaluating a portfolio of improvement projects and combine this evaluation with the effect they have on the CMMI maturity level. Further, the paper demonstrates how the combination of a strong senior management requirement for improved maturity and the focus on getting the most value out of PPM made...

Tissue distribution, metabolism, and residue depletion study in Atlantic salmon following oral administration of [3H]emamectin benzoate.

Science.gov (United States)

Kim-Kang, Heasook; Bova, Alice; Crouch, Louis S; Wislocki, Peter G; Robinson, Robert A; Wu, Jinn

2004-04-07

Atlantic salmon (approximately 1.3 kg) maintained in tanks of seawater at 5 +/- 1 degrees C were dosed with [3H]emamectin B1 benzoate in feed at a nominal rate of 50 microg of emamectin benzoate/kg/day for 7 consecutive days. Tissues, blood, and bile were collected from 10 fish each at 3 and 12 h and at 1, 3, 7, 15, 30, 45, 60, and 90 days post final dose. Feces were collected daily from the tanks beginning just prior to dosing to 90 days post final dose. The total radioactive residues (TRR) of the daily feces samples during dosing were 0.25 ppm maximal, and >97% of the TRR in pooled feces covering the dosing period was emamectin B1a. Feces TRR then rapidly declined to approximately 0.05 ppm by 1 day post final dose. The ranges of mean TRR for tissues over the 90 days post dose period were as follows: kidney, 1.4-3 ppm; liver, 1.0-2.3 ppm; skin, 0.04-0.09 ppm; muscle, 0.02-0.06 ppm; and bone, emamectin B1a (81-100% TRR) and desmethylemamectin B1a (0-17% TRR) with N-formylemamectin B1a seen in trace amounts (emamectin residues was emamectin B1a. The emamectin B1a level was quantified in individual samples of skin and muscle using HPLC-fluorometry and was below 85 ppb in all samples analyzed (3 h to 30 days post dose).

Residual viral and bacterial contamination of surfaces after cleaning and disinfection.

Science.gov (United States)

Tuladhar, Era; Hazeleger, Wilma C; Koopmans, Marion; Zwietering, Marcel H; Beumer, Rijkelt R; Duizer, Erwin

2012-11-01

Environmental surfaces contaminated with pathogens can be sources of indirect transmission, and cleaning and disinfection are common interventions focused on reducing contamination levels. We determined the efficacy of cleaning and disinfection procedures for reducing contamination by noroviruses, rotavirus, poliovirus, parechovirus, adenovirus, influenza virus, Staphylococcus aureus, and Salmonella enterica from artificially contaminated stainless steel surfaces. After a single wipe with water, liquid soap, or 250-ppm free chlorine solution, the numbers of infective viruses and bacteria were reduced by 1 log(10) for poliovirus and close to 4 log(10) for influenza virus. There was no significant difference in residual contamination levels after wiping with water, liquid soap, or 250-ppm chlorine solution. When a single wipe with liquid soap was followed by a second wipe using 250- or 1,000-ppm chlorine, an extra 1- to 3-log(10) reduction was achieved, and except for rotavirus and norovirus genogroup I, no significant additional effect of 1,000 ppm compared to 250 ppm was found. A reduced correlation between reduction in PCR units (PCRU) and reduction in infectious particles suggests that at least part of the reduction achieved in the second step is due to inactivation instead of removal alone. We used data on infectious doses and transfer efficiencies to estimate a target level to which the residual contamination should be reduced and found that a single wipe with liquid soap followed by a wipe with 250-ppm free chlorine solution was sufficient to reduce the residual contamination to below the target level for most of the pathogens tested.

Demand outlook for ultra-low sulfur diesel (10PPM) in Brasil; Perspectiva da demanda de diesel 10 PPM no Brasil

Energy Technology Data Exchange (ETDEWEB)

Aragao, Amanda P.; Saide, Clara Santos Martins; Machado, Giovani V.; Cavalcanti, Marcelo C.B.; Valle, Ricardo Nascimento e Silva do [Empresa de Pesquisa Energetica (EPE), Rio de Janeiro, RJ (Brazil)

2012-07-01

The purpose of this study is to assess the forecast for the diesel 10 ppm demand in the next years, by applying a bottom-up model for heavy vehicles. The relevance of this issue is evidenced by the deadline to obey a Judicial Agreement (signed in 2008 between the Federal Public Ministry, the automotive industry and other entities) and Resolution n. 403/2008 (CONAMA), which establishes that motor suitable for the use of diesel 10 ppm (P-7 Phase) is mandatory for heavy vehicles as of 2012 and that such fuel (diesel 10 ppm) must be supplied from 2013 on. Thus, the diesel national market will face important changes, either on the supply side (refining and logistics), in order to provide diesel 10 ppm, or on the demand side, with the new trucks and buses put into circulation with different motors. Particularly, on the demand side, the potential market, mainly the diesel 10 ppm portion, will be defined by the perspective of the fleet growth, energy efficiency increase and mileage variations for trucks and buses. Under the assumptions considered by this study, the demand for diesel 10 ppm for heavy vehicles will reach 27,9 million m{sup 3} in 2020.(author)

Content Of 2,4-D-14C Herbicide Residue In Water And Soil Of Irrigated Rice Field System

International Nuclear Information System (INIS)

Chairul, Sofnie M.; Djabir, Elida; Magdalena, Nelly

2000-01-01

The investigation of 2,4-D exp.-14C herbicide residue in water and soil of irrigated rice field system was carried out. Rice plant and weeds (Monochoria vaginalis Burn. F. Presl) were planted in 101 buckets using two kinds of soil condition, I.e. normal soil and 30 % above normal compact soil. After one week planting, the plants were sprayed with 1 u Ci of 2,4-D exp.-14C and 0,4 mg non labeled 2,4-D. The herbicide residue content was determined 0, 2, 4, 8 and 10 weeks after spraying with 2,4-D herbicide. The analysis was done using Combustion Biological Oxidizer merk Harvey ox-400, and counted with Liquid Scintillation Counter merk Beckman model LS-1801. The results indicates that the herbicide contents in water and soil decrease from the first spraying with herbicide until harvest herbicide Residue content in water after harvest was 0.87 x 10 exp.-6 ppm for soil normal condition, and 0.59 x 10 exp.-6 pm for the soil 30 % up normal condition, while herbicide content in soil was 1.54 x 10 exp.-6 ppm for soil normal condition and 1.48 x 10 exp.-6 ppm for soil 30 % up normal. 2,4-D herbicide residue content in rice after harvest was 0.27 x 10 exp.-6 ppm for normal soil condition and 0.25 x 10 exp.-6 ppm for the soil 30 % up normal. 2,4-D herbicide residue content in roots and leaves of weeds after harvest were respectively 0.29 x 10 exp.-6 ppm and 0.18 x 10 exp.-6 for normal soil condition, while for 30 % up normal soil were 0.25 x 10 exp.-5 ppm and 0.63 x 10 exp.-7 ppm. This result indicates that there is no effect pollution to surrounding area, because the herbicide content is still bellow the allowed detection limit, 0.05 ppm

Residues of organochlorine pesticides, mercury, and PCB's in mourning doves from eastern United States--1970-71

Science.gov (United States)

Kreitzer, J.F.

1974-01-01

Mourning dove (Zenaidura macroura) breast muscle samples from birds collected in 1970-71 from Rhode Island, Pennsylvania, Maryland, Missouri, Kentucky, Virginia, Arkansas, Tennessee, North Carolina, South Carolina, Mississippi, Alabama, Georgia, Louisiana, and Florida were found to contain residues of DDT, DDE, DDD, polychlorinated biphenyls, dieldrin, mirex, mercury, and heptachlor epoxide in amounts not considered hazardous to consumers, human or nonhuman. There were 145 birds involved, 7 to 10 from each State. Residues of DDT plus DDE plus DDD averaged 5.83 ppm lipid weight (0.068 ppm wet weight); those of PCB's, 9.75 ppm lipid weight (0.121 ppm wet weight); compounds were found in all birds. Heptachlor epoxide and dieldrin were found in little more than trace amounts: heptachlor in all birds, dieldrin in 73. Mirex was found only in birds from South Carolina, Georgia, and Florida, averaging 4.32 ppm lipid weight (0.046 ppm wet weight) in eight birds. Less than 0.05 ppm (wet weight) mercury was found in all birds except 10, in which it ranged from 0.07 to 0.67 ppm. The 10 were from Rhode Island, Pennsylvania, Maryland, Virginia, Tennessee, and Alabama.

Waste Treatment of Chrome Residue of Chromium Recovery Process Using Calcium Carbonate

International Nuclear Information System (INIS)

Endro Kismolo; Prayitno; Nurimaniwathy

2002-01-01

The aim of the research was to apply the precipitation technology for the treatment of aqueous wastes of leather tanning industries. The chrome liquid wastes taken was the effluent from the residue of the chromium recovery process using magnesium oxide. The precipitant used was calcium carbonate. The experiments was performed by adjusting the concentration of calcium carbonate from 50 ppm, 100 ppm, 150 ppm, 200 ppm, 250 ppm, 300 ppm, 350 ppm to 400 ppm. The stirring speed was varied from 50 rpm, 75 rpm, 100 rpm, 125 rpm, 150 rpm, 175 rpm to 200 rpm. The time of mixing was varied from 30 minutes, 60 minutes, 90 minutes, 120 minutes, 150 minutes, 175 minutes and 200 minutes. The result from the experiments lead to the best condition obtained were the concentration of precipitant was 300 ppm, flow rates of mixing was 125 rpm and time of mixing was 60 minutes. At this condition the separations efficiency of chrome obtained was 99.985%. (author)

Iron-Mediated Homogeneous ICAR ATRP of Methyl Methacrylate under ppm Level Organometallic Catalyst Iron(III Acetylacetonate

Directory of Open Access Journals (Sweden)

Jian Wu

2016-01-01

Full Text Available Atom Transfer Radical Polymerization (ATRP is an important polymerization process in polymer synthesis. However, a typical ATRP system has some drawbacks. For example, it needs a large amount of transition metal catalyst, and it is difficult or expensive to remove the metal catalyst residue in products. In order to reduce the amount of catalyst and considering good biocompatibility and low toxicity of the iron catalyst, in this work, we developed a homogeneous polymerization system of initiators for continuous activator regeneration ATRP (ICAR ATRP with just a ppm level of iron catalyst. Herein, we used oil-soluble iron (III acetylacetonate (Fe(acac3 as the organometallic catalyst, 1,1′-azobis (cyclohexanecarbonitrile (ACHN with longer half-life period as the thermal initiator, ethyl 2-bromophenylacetate (EBPA as the initiator, triphenylphosphine (PPh3 as the ligand, toluene as the solvent and methyl methacrylate (MMA as the model monomer. The factors related with the polymerization system, such as concentration of Fe(acac3 and ACHN and polymerization kinetics, were investigated in detail at 90 °C. It was found that a polymer with an acceptable molecular weight distribution (Mw/Mn = 1.43 at 45.9% of monomer conversion could be obtained even with 1 ppm of Fe(acac3, making it needless to remove the residual metal in the resultant polymers, which makes such an ICAR ATRP process much more industrially attractive. The “living” features of this polymerization system were further confirmed by chain-extension experiment.

Survey of Diazinon and Chlorpyrifos Pesticide Residues in the Corp of Apple (Red Delicious Variety of Miyandoab’s Springhouses by Using HPLC-PDA

Directory of Open Access Journals (Sweden)

H. Shahyan

2017-07-01

Full Text Available In this research to investigate the probable contamination of the apple tree to pesticides that is used by farmers in Miandoab, the residues of Diazinon and Chlorpirifos were investigated in this crop. First, the sampling is carried out by using the simple random sampling method and then, after Solid Phase Extraction (SPE through High-Performance Liquid Chromatography (HPLC, the residues of Diazinon and chlorpirifos were measured. So that, the pesticides residues in apples that were washed with skin, without skin and, in peeled apples were measured 0.08, 0.31, 0.68 ppm for Diazinon and 0.24, 0.54, 0.98 ppm for Chlorpirifos, respectively. Comparison of the statistical results with global standards reveals that the residues of Diazinon in Apples with the skin, and the residues of Chlorpirifos in three modes: Unwashed with the skin, washed with the skin and peeled is more than global standards (Diazinon 0.5 ppm and Chlorpirifos 0.01 ppm Therefore, it is required that the authorities and farmers of this region pay special attention to residues and the time of applying pesticides; thereby, they can prevent endangering health society.

Design of Optical Pulse Position Modulation (PPM) Translating Receiver

Energy Technology Data Exchange (ETDEWEB)

Mendez, A J; Hernandez, V J; Gagliardi, R M; Bennett, C V

2009-06-19

M-ary pulse position modulation (M-ary PPM) signaling is a means of transmitting multiple bits per symbol in an intensity modulated/direct detection (IM/DD) system. PPM is used in applications with average power limitations. In optical communication systems, PPM becomes challenging to implement at gigabit rates and/or large M, since pulsed signaling requires higher electronic processing bandwidths than the fundamental transmission rate. they have thus been exploring techniques for PPM communications using optical processing. Previous work described a transmitter algorithm that directly translates a bit sequence of N digital bits to the optical pulse position m for any M = 2{sup N}. It has been considerably more difficult to define a similar receiver algorithm that translates the received optical pulse position directly back to a bit sequence with minimal electronic processing. Designs for specific Ms (e.g., 4-ary) have been shown and implemented, but are difficult to scale to larger M. In this work, they present for the first time a generalized PPM translating receiver that is applicable to all M and data rates.

Application of a portable total reflection x-ray fluorescence spectrometer to a trace elemental analysis of wines

International Nuclear Information System (INIS)

Kunimura, Shinsuke; Kawai, Jun

2009-01-01

A portable total reflection X-ray fluorescence (TXRF) spectrometer has been applied to a trace elemental analysis of wines. Sulfur, K, Mn, Fe, and Rb were detected. These five elements were quantified by using 1 ppm of Co as an internal standard. The quantified concentrations ranged from sub-ppm to several hundred ppm. Because of organic substances in wines, the scattering of the incident X-rays from the dry residues of wines becomes strong. Therefore, a high spectral background appears in TXRF spectra of wines. Because of this background, relative standard deviations of the quantified concentrations were from 4 to 28%. Although the high spectral background appeared in the TXRF spectra of the wines, a detection limit down to several tens of ppb was achieved. The present portable spectrometer can be applied to screening for trace elements in wines before an accurate and precise analysis using a large elemental analyzer. (author)

Effect of a 5000 ppm fluoride toothpaste and a 250 ppm fluoride mouth rinse on the demineralisation of dentin surfaces.

Science.gov (United States)

Bizhang, Mozhgan; Chun, Yong-Hee P; Winterfeld, Mai-Trinh; Altenburger, Markus J; Raab, Wolfgang H M; Zimmer, Stefan

2009-07-23

The purpose of this study was to test the null hypothesis that there is no difference between the effect of (1) a 5000 ppm fluoride toothpaste, and (2) a 250 ppm fluoride mouth rinse on demineralized human dentin surfaces, against the alternative hypothesis of a difference. Dentin specimens were obtained from the cervical regions of 45 extracted human third molars. Half the surface of each specimen was sealed with a self-etching adhesive system and served as the reference surface. The dentin specimens were randomly assigned to one of the three groups, 5000 ppm fluoride toothpaste (Duraphat), 250 ppm fluoride mouth rinse (Meridol) and distilled water (negative control).An intraoral appliance was made for one volunteer. In each test cycle, 15 specimens were inserted in the appliance and worn for 24 hours a day, over a period of three weeks.Once daily, the appliance was immersed in the agent being tested; either toothpaste slurry, mouth rinse or distilled water for 60 seconds.Demineralization was assessed in terms of lesion depth (microm) and mineral loss (vol. % x microm) by transversal microradiography. Data analysis was accomplished using Kolmogorov-Smirnov test and ANOVA (SPSS 12.0).Statistically significant differences for mineral loss and lesion depth were found between the toothpaste and the mouth rinse as well as between the toothpaste and the control group, but not between the mouth rinse and the control group. Within the limitations of this study, the results suggest that treatment of demineralised dentin with a toothpaste containing 5000 ppm fluoride may considerably reduce mineral loss and lesion depth on exposed dentin.

A study of neurotoxicity of BHC in relation to residual accumulation on the brain tissue of Heteropneustes fossilis (Bloch).

Science.gov (United States)

Hazarika, Ranjit

2003-01-01

Neurotoxic effect of BHC, the organochlorine pesticide in Heteropneustes fossilis has been studied exposing at the dose concentrations of 1 ppm, 5 ppm and 10 ppm in lab aquarium for 96 hours over a period of one year. The results showed the behavioural abnormalities in different exposure concentrations such as dysfunction of endocrine gland, excretion of mucus, dispigmentation, sign of restlessness, erratic swimming with rapid jurkey movement, spiralling and convolution showing severe effect in central nervous system. Therefore an attempt has been made for monitoring of BHC residues viz. alpha, beta, gamma isomers in the brain tissue exposed to different sublethal concentrations using Gas liquid chromatography. The mean values of isomers were found to be 1.587 microg/gm for 1 ppm, 2.993 microg/gm for 5 ppm and 3.78 microg/gm for 10 ppm test group. Severe behavioural abnormalities were recorded at high dose concentration of pesticides with higher accumulation of pesticide residues in brain tissue.

Cyolane residues in milk of lactating goats

International Nuclear Information System (INIS)

Zayed, S.M.A.D.; Osman, A.; Fakhr, I.M.I.

1981-01-01

Consecutive feeding of lactating goats with 14 C-alkyl labelled cyolane for 5 days at dietary levels 8 and 16 ppm resulted in the appearance of measurable insecticide residues in milk (0.02-0.04 mg/kg). The residue levels were markedly reduced after a withdrawal period of 7 days. Analysis of urine and milk residues showed the presence of similar metabolites in addition to the parent compound. The major part of the residue consisted of mono-, diethyl phosphate and 2 hydrophilic unknown metabolites. The erythrocyte cholinesterase activity was reduced to about 50% after 24 hours whereas the plasma enzyme was only slightly affected. The animals remained symptom-free during the experimental period. (author)

The role of phosphites in scab management and residues in pecan kernels

Science.gov (United States)

Phosphite fungicides are used to manage pecan scab (caused by Fusicladium effusum), the most economically destructive disease of pecan in the Southeast US. The EU has imposed a minimum residue limit (MRL) on these fungicides in pecan kernels. Data shows that the phosphite residue exceeds the 2 ppm M...

Determination of Profenofos Pesticidal Residue in Lettuce (Lactuca sativa L. by Gas Chromatographic Method

Directory of Open Access Journals (Sweden)

Yohannes Alen

2015-05-01

Full Text Available The determination of profenofos pesticidal residue in the lettuce (Lactuca sativa L. by using gas chromatography using flame photometric detector (FPD had been investigated. The lettuce was collected from Padang Luar area, Agam distric, West Sumatera. Sample for determination of profenofos residue divided into three groups: unwashed (A, washed with water (B, and washed with detergent (C. Maceration with sonication was used for the extraction using ethylacetateas a solvent. The results showed that profenofos pesticide residue in sample A, B and C were 0.204, 0.080 and 0.061 ppm, respectively. These profenofos pesticidal residue are over than the Maximum Residue Limits (MRL that established by The Japan Food Chemical Research Foundation (0.05 ppm even though World Health Organization (WHO has not established Maximum Residue Limits (MRL profenofos on lettuce. Based on the statistical analysis one-way method (Anova using SPSS 20.0 showed that there was a significant concentrations difference between lettuce A from lettuce B and lettuce C with p < 0.05.

Inter-Symbol Guard Time for Synchronizing Optical PPM

Science.gov (United States)

Far, William; Gin, Jonathan; Srinivasan, Meera; Quirk, Kevin

2009-01-01

An inter-symbol guard time has been proposed as a means of synchronizing the symbol and slot clocks of an optical pulse-position modulation (PPM) receiver with the symbol and slot periods of an incoming optical PPM signal.The proposal is applicable to the low-flux case in which the receiver photodetector operates in a photon-counting mode and the count can include contributions from incidental light sources and dark current.

Determination of oxyfluorfen herbicide and oxyfluorfen amine residues in garbanzo beans by liquid chromatography.

Science.gov (United States)

Zhou, M; Miles, C J

1991-01-01

Oxyfluorfen and oxyfluorfen amine were determined by liquid chromatography (LC) with ultraviolet (UV) and photoconductivity detection (PCD). A simple extraction procedure acceptably recovered both analytes from garbanzo beans over a wide range of fortifications (0.05 to 20 ppm) (83 +/- 4 for oxyfluorfen; 85 +/- 4 for oxyfluorfen amine). Percent recoveries decreased slightly as the fortification level decreased. Both analytes could be determined simultaneously at a concentration greater than 0.2 ppm in garbanzo beans. Detection limits were 3 ng for oxyfluorfen and 100 ng for oxyfluorfen amine using LC/UV, and 12 ng for both oxyfluorfen and oxyfluorfen amine with LC/PCD. Different knitted reaction coils and photoreactors were evaluated. Photoproduct yields and identification were determined by ion chromatography. The LC/PCD method measures oxyfluorfen and oxyfluorfen amine separately and has a shorter analysis time, while the standard method using gas chromatography measures total residues and is more sensitive.

The effect of commercial processing procedures on 14C-carbendazim residues in soybean oil and tomato

International Nuclear Information System (INIS)

Peng Genyuan; Wang Huaguo; Qi Mengwen; Wang Fujun; Zhou Changjiu

1994-01-01

Under simulated agricultural practices, soybean plants were treated with 14 C-labelled carbendazim during the blooming stage. The residue in seeds was determined to be 0.067 ppm; corresponding to 0.076 ppm respectively. After subjecting the oil to degumming, alkali treatment, bleaching and deodorization, 53.7% of original radioactivity was removed. Deodorization was the most effect process, removing about 20% of the residue. The concentration of residues in the deodorized oil decreased about 30%. In soybean seed and cake, the residue was mainly present as carbendazim, the concentration of the other metabolites did not exceed 30% of the residue. Tomatoes grown on a field plot were treated with 14 C-carbendazim. After harvest, the tomatoes were processed into tomato juice and canned whole fruit. The magnitude and nature of residues in samples taken at several processing steps were determined to evaluate the effect of commercial processing on removing or eliminating the residues. The results showed that the surface residues on tomato would be removed efficiently by simple washing of tomato. A buffer solution of phosphate had the highest efficiency. Tomato juice contained lower residues than canned whole fruit

Optical Phase Recovery and Locking in a PPM Laser Communication Link

Science.gov (United States)

Aveline, David C.; Yu, Nan; Farr, William H.

2012-01-01

Free-space optical communication holds great promise for future space missions requiring high data rates. For data communication in deep space, the current architecture employs pulse position modulation (PPM). In this scheme, the light is transmitted and detected as pulses within an array of time slots. While the PPM method is efficient for data transmission, the phase of the laser light is not utilized. The phase coherence of a PPM optical signal has been investigated with the goal of developing a new laser communication and ranging scheme that utilizes optical coherence within the established PPM architecture and photon-counting detection (PCD). Experimental measurements of a PPM modulated optical signal were conducted, and modeling code was developed to generate random PPM signals and simulate spectra via FFT (Fast Fourier Transform) analysis. The experimental results show very good agreement with the simulations and confirm that coherence is preserved despite modulation with high extinction ratios and very low duty cycles. A real-time technique has been developed to recover the phase information through the mixing of a PPM signal with a frequency-shifted local oscillator (LO). This mixed signal is amplified, filtered, and integrated to generate a voltage proportional to the phase of the modulated signal. By choosing an appropriate time constant for integration, one can maintain a phase lock despite long dark times between consecutive pulses with low duty cycle. A proof-of-principle demonstration was first achieved with an RF-based PPM signal and test setup. With the same principle method, an optical carrier within a PPM modulated laser beam could also be tracked and recovered. A reference laser was phase-locked to an independent pulsed laser signal with low-duty-cycle pseudo-random PPM codes. In this way, the drifting carrier frequency in the primary laser source is tracked via its phase change in the mixed beat note, while the corresponding voltage feedback

Influence of gamma rays irradiation to chlorphyriphos insecticides residues in grapes (vitis vinifera L.)

International Nuclear Information System (INIS)

Chairul, S.M.

2012-01-01

Simulation methods to determination of chlorphyriphos insecticides residue in grapes cause effect gamma rays, was done. Fruits of grapes soaked with chlorpyriphos insecticide solution high level concentrated (100 ppm; 200 ppm; and 300 ppm) for 3 (three minutes). The treatment of the sample was direct of extraction after soaks; extract after storage for one week after soak, and extract after soak after storage for one week after irradiation at 0.5 kGy; 1.0 kGy; and 1.5 kGy dose. Extraction methods using ethyl acetate solvent, and using sodium sulphate as to dryed water level in grapes, and then extractan was injected to chromatography gas use electron capture detector. The result indicated that occur of descent of chlorpyrifos residues from eachs soaked consequence at storage for one week was amount 7,55; 8,42; and 18,88% respectively, while of consequence irradiation of gamma ray at 0,5 kGy doses, will be descent of chlorpyrifos residues in amount 13,90; 19,16; and 52,79% respectively, and at 1,0 kGy doses irradiation will be descent in amount 34,45; 36,15 and 49,79%, respectively. (author)

Protein phosphatase magnesium-dependent 1δ (PPM1D mRNA expression is a prognosis marker for hepatocellular carcinoma.

Directory of Open Access Journals (Sweden)

Guang-Bing Li

Full Text Available Protein phosphatase magnesium-dependent 1δ (PPM1D is an oncogene, overexpressed in many solid tumors, including ovarian cancer and breast cancer. The current study examined the expression and the prognostic value of PPM1D mRNA in human hepatocellular carcinoma (HCC.Total RNA was extracted from 86 HCC and paired non-cancerous liver tissues. PPM1D mRNA expression was determined by real-time quantitative reverse transcriptase-polymerase chain reaction (qPCR. Immunohistochemistry assay was used to verify the expression of ppm1d protein in the HCC and non-cancerous liver tissues. HCC patients were grouped according to PPM1D mRNA expression with the average PPM1D mRNA level in non-cancerous liver tissue samples as the cut-off. Correlations between clinicopathologic variables, overall survival and PPM1D mRNA expression were analyzed.PPM1D mRNA was significantly higher in HCC than in the paired non-cancerous tissue (p<0.01. This was confirmed by ppm1d staining. 56 patients were classified as high expression group and the other 30 patients were categorized as low expression group. There were significant differences between the two groups in term of alpha-fetoprotein (α-FP level (p<0.01, tumor size (p<0.01, TNM stage (p<0.01, recurrence incidence (p<0.01 and family history of liver cancer (p<0.01. The current study failed to find significant differences between the two groups in the following clinical characteristics: age, gender, portal vein invasion, lymphnode metastasis, hepatitis B virus (HBV infection and alcohol intake. Survival time of high expression group was significantly shorter than that of low expression group (median survival, 13 months and 32 months, respectively, p<0.01.Up-regulation of PPM1D mRNA was associated with progressive pathological feature and poor prognosis in HCC patients. PPM1D mRNA may serve as a prognostic marker in HCC.

The effect of commercial processing procedures on {sup 14}C-carbendazim residues in soybean oil and tomato

Energy Technology Data Exchange (ETDEWEB)

Genyuan, Peng; Huaguo, Wang; Mengwen, Qi; Fujun, Wang; Changjiu, Zhou [Laboratory for the Application of Nuclear Techniques, Beijing Agricultural University, Beijing (China)

1994-06-01

Under simulated agricultural practices, soybean plants were treated with {sup 14}C-labelled carbendazim during the blooming stage. The residue in seeds was determined to be 0.067 ppm; corresponding to 0.076 ppm respectively. After subjecting the oil to degumming, alkali treatment, bleaching and deodorization, 53.7% of original radioactivity was removed. Deodorization was the most effect process, removing about 20% of the residue. The concentration of residues in the deodorized oil decreased about 30%. In soybean seed and cake, the residue was mainly present as carbendazim, the concentration of the other metabolites did not exceed 30% of the residue. Tomatoes grown on a field plot were treated with {sup 14}C-carbendazim. After harvest, the tomatoes were processed into tomato juice and canned whole fruit. The magnitude and nature of residues in samples taken at several processing steps were determined to evaluate the effect of commercial processing on removing or eliminating the residues. The results showed that the surface residues on tomato would be removed efficiently by simple washing of tomato. A buffer solution of phosphate had the highest efficiency. Tomato juice contained lower residues than canned whole fruit.

Effects of high-fluoride dentifrice (5,000-ppm) on caries-related plaque and salivary variables

NARCIS (Netherlands)

Mannaa, A.; Carlén, A.; Zaura, E.; Buijs, M.J.; Bukhary, S.; Lingström, P.

2014-01-01

Objectives The aim of the present study was to measure the effects of a 5,000-ppm F toothpaste on caries-related factors in dental plaque and saliva. Materials and methods A 6-week clinical trial was designed with a total of 34 participants, of which 26 completed the study. The participants were

Thorium, uranium and rare earth elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas advanced materials plant (LAMP)

Science.gov (United States)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman

2014-02-01

Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and γ-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 ± 129 ppm (5274.9 ± 527.6Bq/kg) whereas the Th and U concentrations in WLP were determined to be 1952.9±17.6 ppm (7987.4 ± 71.9 Bq/kg) and 17.2 ± 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by γ- spectrometry were 1156 ppm (4728 ± 22 Bq/kg) & 18.8 ppm and 1763.2 ppm (7211.4 Bq/kg) &29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of 232Th compared to Malaysian soil natural background (63 - 110 Bq/kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 ± 0.6% and 4.7 ± 0.1% respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 ± 0.04%, 1.6%, 0.22% and 0.06% respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be reextracted.

Thorium, uranium and rare earth elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas advanced materials plant (LAMP)

International Nuclear Information System (INIS)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman

2014-01-01

Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and γ-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 ± 129 ppm (5274.9 ± 527.6Bq/kg) whereas the Th and U concentrations in WLP were determined to be 1952.9±17.6 ppm (7987.4 ± 71.9 Bq/kg) and 17.2 ± 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by γ- spectrometry were 1156 ppm (4728 ± 22 Bq/kg) and 18.8 ppm and 1763.2 ppm (7211.4 Bq/kg) and 29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of 232 Th compared to Malaysian soil natural background (63 - 110 Bq/kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 ± 0.6% and 4.7 ± 0.1% respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 ± 0.04%, 1.6%, 0.22% and 0.06% respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be reextracted

Thorium, Uranium and Rare Earth Elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas Advanced Materials Plant (LAMP)

International Nuclear Information System (INIS)

Al-Areqi, W.M.; Amran Abdul Majid; Sukiman Sarmani

2013-01-01

Full-text: Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and γ-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 ± 129 ppm (5274.9 ± 527.6 Bq/ kg) whereas the Th and U concentrations in WLP were determined to be 1952.9 ± 17.6 ppm (7987.4 ± 71.9 Bq/ kg) and 17.2 ± 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by γ- spectrometry were 1156 ppm (4728 ± 22 Bq/ kg) and 18.8 ppm and 1763.2 ppm (7211.4 Bq/ kg) and 29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of 232 Th compared to Malaysian soil natural background (63 - 110 Bq/ kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 ± 0.6 % and 4.7 ± 0.1 % respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 ± 0.04 %, 1.6 %, 0.22 % and 0.06 % respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be re

Thorium, uranium and rare earth elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas advanced materials plant (LAMP)

Energy Technology Data Exchange (ETDEWEB)

AL-Areqi, Wadeeah M., E-mail: walareqi@yahoo.com; Majid, Amran Ab., E-mail: walareqi@yahoo.com; Sarmani, Sukiman, E-mail: walareqi@yahoo.com [Nuclear Science Programme, School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi (Malaysia)

2014-02-12

Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and γ-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 ± 129 ppm (5274.9 ± 527.6Bq/kg) whereas the Th and U concentrations in WLP were determined to be 1952.9±17.6 ppm (7987.4 ± 71.9 Bq/kg) and 17.2 ± 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by γ- spectrometry were 1156 ppm (4728 ± 22 Bq/kg) and 18.8 ppm and 1763.2 ppm (7211.4 Bq/kg) and 29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of {sup 232}Th compared to Malaysian soil natural background (63 - 110 Bq/kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 ± 0.6% and 4.7 ± 0.1% respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 ± 0.04%, 1.6%, 0.22% and 0.06% respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be reextracted.

Total effects of contact and residual exposure of bifenthrin and λ-cyhalothrin on the predatory mite Galendromus occidentalis (Acari: Phytoseiidae).

Science.gov (United States)

Hamby, Kelly A; Alifano, Jesse A; Zalom, Frank G

2013-10-01

Pyrethroid insecticides are generally regarded as acutely toxic to predatory phytoseiid mites; however, persistence of hull split spray pyrethroid residues on almond trees and their effects on phytoseiids have not been quantified over time. Hull split, the separation of the almond hull along the suture, exposes the new crop nuts to infestation by Amyelois transitella (Walker) larvae, and is the preferred timing for insecticides applied for their control. Galendromus occidentalis (Nesbitt) is the most important phytoseiid biocontrol agent for web-spinning spider mites in California (USA) almond orchards, and the impact of bifenthrin and λ-cyhalothrin pyrethroid residue on their survival, fertility, and fecundity was determined. The total effects of direct contact with esfenvalerate, permethrin, bifenthrin and λ-cyhalothrin were also evaluated for comparison. The total effects (E) of direct contact treatments of the four pyrethroids ranged from 77.8 % for esfenvalerate to 98.8 % for bifenthrin. Both bifenthrin and λ-cyhalothrin twig residue would be considered harmful (IOBC class 4) following field application at hull split timing. Bifenthrin twig residue would be considered slightly harmful (IOBC class 2) for up to 3.5 months and harmless (IOBC class 1) after 6 months. λ-cyhalothrin residue would be considered moderately harmful (IOBC class 3) for up to 3.5 months following application and harmless (IOBC class 1) after 6 months. Bifenthrin and λ-cyhalothrin twig residue on treated trees significantly reduced G. occidentalis female survival for up to 6 months post-treatment, however total effects (E) classify these residues as harmless (IOBC class 1) after 6 months. Harmful effects of direct and residual exposure following application have implications for the use of these pyrethroids in an integrated mite management program for perennial crops.

Virtual Array Receiver Options for 64-ary Pulse Position Modulation (PPM)

Energy Technology Data Exchange (ETDEWEB)

Mendez, A J; Hernandez, V J; Gagliardi, R M; Bennett, C V

2009-01-12

NASA is developing technology for 64 64-ary PPM using relatively large PPM time slots (10 ns) an and relatively simple d electronic electronic-based receiver logic. In this paper we describe photonic photonics-based receiver options for the case of much higher data rates and inherently shorter decision times. The receivers take the form of virtual ( array or quadrant) arrays with associated comparison tests. Previously we explored this concept for 4-ary and 16-ary PPM at data rates of up to 10 Gb/s. The lessons learned are applied to the case of 64 64-ary PPM at 1.25 Gb/s s. Various receiver designs are compare, and t the optimum design, based on virtual array he arrays, is s, evaluated using numerical simulations.

Studies of pirimiphos-methyl residues in stored rice, using 14C-pirimiphos-methyl

International Nuclear Information System (INIS)

Varca, L.M.; Sanchez, T.E.; Gambalan, N.; Magallona, E.D.

1990-01-01

The distribution and persistence of pirimiphos-methyl on rice (hulled and unhulled) stored over a period of 6 months at 30 deg. C and about 11% moisture were studied using 14 C labelled insecticide. The procedures used for preparing the labelled formulation, applying the insecticide and for the handling and analysis of the grain samples were similar to those described for fenvalerate, see Varca, Sanchez and Magallona, ''Isotopic tracer aided studies of fenvalerate residues in stored products'', these Proceedings. After applying the pirimiphos-methyl, a concentration equal to 0.87 ppm was found on the hulled rice immediately after application; this concentration declined to 0.60 ppm after 6 months of storage. Over 28% of the residue was present in the seed in the methanol extractable form, and 38% was found on the surface at the end of the storage period. For the unhulled rice, most of the residue was retained in the hull with no decrease in the overall level during the storage period. (author)

Total gamma activity measurements for determining the radioactivity of residual materials from nuclear power stations

International Nuclear Information System (INIS)

Auler, I.; Meyer, M.; Stickelmann, J.

1995-01-01

Large amounts of residual materials from retrofitting measures and from decommissioning of nuclear power stations shows such a weak level of radioactivity that they could be released after decision measurements. Expenses incurred with complex geometry cannot be taken with common methods. NIS developed a Release Measurement Facility (RMF) based on total gamma activity measurements especially for these kind of residual materials. The RMF has been applied for decision measurements in different nuclear power plants. Altogether about 2,000 Mg of various types of materials have been measured up to now. More than 90 % of these materials could be released 0 without any restriction after decision measurements

Error-Rate Bounds for Coded PPM on a Poisson Channel

Science.gov (United States)

Moision, Bruce; Hamkins, Jon

2009-01-01

Equations for computing tight bounds on error rates for coded pulse-position modulation (PPM) on a Poisson channel at high signal-to-noise ratio have been derived. These equations and elements of the underlying theory are expected to be especially useful in designing codes for PPM optical communication systems. The equations and the underlying theory apply, more specifically, to a case in which a) At the transmitter, a linear outer code is concatenated with an inner code that includes an accumulator and a bit-to-PPM-symbol mapping (see figure) [this concatenation is known in the art as "accumulate-PPM" (abbreviated "APPM")]; b) The transmitted signal propagates on a memoryless binary-input Poisson channel; and c) At the receiver, near-maximum-likelihood (ML) decoding is effected through an iterative process. Such a coding/modulation/decoding scheme is a variation on the concept of turbo codes, which have complex structures, such that an exact analytical expression for the performance of a particular code is intractable. However, techniques for accurately estimating the performances of turbo codes have been developed. The performance of a typical turbo code includes (1) a "waterfall" region consisting of a steep decrease of error rate with increasing signal-to-noise ratio (SNR) at low to moderate SNR, and (2) an "error floor" region with a less steep decrease of error rate with increasing SNR at moderate to high SNR. The techniques used heretofore for estimating performance in the waterfall region have differed from those used for estimating performance in the error-floor region. For coded PPM, prior to the present derivations, equations for accurate prediction of the performance of coded PPM at high SNR did not exist, so that it was necessary to resort to time-consuming simulations in order to make such predictions. The present derivation makes it unnecessary to perform such time-consuming simulations.

Applying PPM to ERP Maintenance and Continuous Improvement Initiatives

DEFF Research Database (Denmark)

El-Tal, Nada Maria; Fonnesbæk, Majbrit; Kræmmergaard, Pernille

2006-01-01

to gain business benefits from the systems. However the ERP literature on how to do this is limited. The purpose of this article is to explore how Project Portfolio Management (PPM) from the Research and Development (R&D) literature can be applied to an ERP second wave context, when companies...... are to prioritize and select maintenance and continuous improvement initiatives. This is done by reviewing the existing literature in the fields of PPM from R&D literature and then by reviewing the existing literature about maintenance and improvement initiatives in the ERP literature, after which the two...... are compared and discussed using three case-studies. The paper contributes with a discussion on how PPM from R&D can be applied to maintenance and continuous improvement initiatives in the second wave of ERP. The paper ends with arguing that emphasis needs to be given to this field, since a conscious...

Sample preparation for total reflection X-ray fluorescence analysis using resist pattern technique

Science.gov (United States)

Tsuji, K.; Yomogita, N.; Konyuba, Y.

2018-06-01

A circular resist pattern layer with a diameter of 9 mm was prepared on a glass substrate (26 mm × 76 mm; 1.5 mm thick) for total reflection X-ray fluorescence (TXRF) analysis. The parallel cross pattern was designed with a wall thickness of 10 μm, an interval of 20 μm, and a height of 1.4 or 0.8 μm. This additional resist layer did not significantly increase background intensity on the XRF peaks in TXRF spectra. Dotted residue was obtained from a standard solution (10 μL) containing Ti, Cr, Ni, Pb, and Ga, each at a final concentration of 10 ppm, on a normal glass substrate with a silicone coating layer. The height of the residue was more than 100 μm, where self-absorption in the large residue affected TXRF quantification (intensity relative standard deviation (RSD): 12-20%). In contrast, from a droplet composed of a small volume of solution dropped and cast on the resist pattern structure, the obtained residue was not completely film but a film-like residue with a thickness less than 1 μm, where self-absorption was not a serious problem. In the end, this sample preparation was demonstrated to improve TXRF quantification (intensity RSD: 2-4%).

Latest Results in SLAC 75-MW PPM Klystrons

International Nuclear Information System (INIS)

Sprehn, D.; Caryotakis, G.; Haase, A.; Jongewaard, E.; Laurent, L.; Pearson, C.; Phillips, R.

2006-01-01

75 MW X-band klystrons utilizing Periodic Permanent Magnet (PPM) focusing have been undergoing design, fabrication and testing at the Stanford Linear Accelerator Center (SLAC) for almost nine years. The klystron development has been geared toward realizing the necessary components for the construction of the Next Linear Collider (NLC). The PPM devices built to date which fit this class of operation consist of a variety of 50 MW and 75 MW devices constructed by SLAC, KEK (Tsukuba, Japan) and industry. All these tubes follow from the successful SLAC design of a 50 MW PPM klystron in 1996. In 2004 the latest two klystrons were constructed and tested with preliminary results reported at EPAC2004. The first of these two devices was tested to the full NLC specifications of 75 MW, 1.6 microseconds pulse length, and 120 Hz. This 14.4 kW average power operation came with a tube efficiency >50%. The most recent testing of these last two devices will be presented here. Design and manufacturing issues of the latest klystron, due to be tested by the Fall of 2005, are also discussed

Forensic Analysis of High Explosive Residues from Selected Cloth

International Nuclear Information System (INIS)

Mohamad Afiq Mohamed Huri; Umi Kalthom Ahmad

2014-01-01

Increased terrorist activities around the Asian region have resulted in the need for improved analytical techniques in forensic analysis. High explosive residues from post-blast clothing are often encountered as physical evidence submitted to a forensic laboratory. Therefore, this study was initiated to detect high explosives residues of cyclotrimethylenetrinitramine (RDX) and pentaerythritol tetranitrate (PETN) on selected cloth in this study. Cotton swabbing technique was employed as a simple and rapid method in recovering analytes from the sample matrix. Analytes were analyzed using Griess spot test, TLC and HPLC. TLC separation employed toluene-ethyl acetate (9:1) as a good solvent system. Reversed phase HPLC separation employed acetonitrile-water (65:35) as the mobile phase and analytes detected using a programmed wavelength. RDX was detected at 235 nm for the first 3.5 min and then switched to 215 nm for PETN. Limits of detection (LODs) of analytes were in the low ppm range (0.05 ppm for RDX and 0.25 ppm for PETN). Analyte recovery studies revealed that the type of cloth has a profound effect on the extraction efficiency. Analytes were recovered better for nylon as compared to cotton cloth. However, no analytes could be recovered from denim cloth. For post-blast samples, only RDX was detected in low concentration for both nylon and cotton cloth. (author)

Influence of thermal expansion mismatch on residual stress profile in veneering ceramic layered on zirconia: Measurement by hole-drilling.

Science.gov (United States)

Mainjot, Amélie K; Najjar, Achref; Jakubowicz-Kohen, Boris D; Sadoun, Michaël J

2015-09-01

Mismatch in thermal expansion coefficient between core and veneering ceramic (Δα=αcore-αveneer, ppm/°C) is reported as a crucial parameter influencing veneer fractures with Yttria-tetragonal-zirconia-polycrystal (Y-TZP) prostheses, which still constitutes a misunderstood problem. However, the common positive Δα concept remains empirical. The objective of this study is to investigate the Δα dependence of residual stress profiles in veneering ceramic layered on Y-TZP frameworks. The stress profile was measured with the hole-drilling method in bilayered disc samples of 20mm diameter with a 0.7mm thick Y-TZP framework and a 1.5mm thick veneer layer. 3 commercial and 4 experimental veneering ceramics (n=3 per group) were used to obtain different Δα varying from -1.3ppm/°C to +3.2ppm/°C, which were determined by dilatometric analyses. Veneer fractures were observed in samples with Δα≥+2.3 or ≤-0.3ppm/°C. Residual stress profiles measured in other groups showed compressive stresses in the surface, these stresses decreasing with depth and then becoming more compressive again near the interface. Small Δα variations were shown to induce significant changes in residual stress profiles. Compressive stress near the framework was found to decrease inversely to Δα. Veneer CTE close to Y-TZP (+0.2ppm/°C Δα) gived the most favorable stress profile. Yet, near the framework, Δα-induced residual stress varied inversely to predictions. This could be explained by the hypothesis of structural changes occurrence within the Y-TZP surface. Consequently, the optimum Δα value cannot be determined before understanding Y-TZP's particular behavior when veneered. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Radiotracer studies of maneb residues in lettuce plants

International Nuclear Information System (INIS)

Sennaoui, Z.; Meguenni, H.; Bennaceur, M.

1990-11-01

Lettuce plants have received different treatments of 14C-maneb at variable time. A cleaning is made to determine the foliar surface residues. The analysis of CS2 showed relatively important amount especially for lots which have received 4 treatments (10,3ppm and 6,49ppm). The amounts found after combustion have showed increasing amounts, proportionally to the number of treatments. The analysis of ETU revealed a presence only for lots which have received several treatments (3 and 4). The analysis by TLC showed many metabolites. Two of them have been identified (ETU, EU). Interfoliar migration of 14C product occurred between treated leaves and untreated leaves of the same plant

Concentration-Response and Residual Activity of Insecticides to Control Herpetogramma phaeopteralis (Lepidoptera: Crambidae) in St. Augustinegrass.

Science.gov (United States)

Tofangsazi, Nastaran; Cherry, Ron H; Beeson, Richard C; Arthurs, Steven P

2015-04-01

Tropical sod webworm, Herpetogramma phaeopteralis Guenée, is an important pest of warm-season turfgrass in the Gulf Coast states of the United States, the Caribbean Islands, and Central America. Current control recommendations rely on topical application of insecticides against caterpillars. The objective of this study was to generate resistance baseline data of H. phaeopteralis to six insecticide classes. Residual activity of clothianidin, chlorantraniliprole, and bifenthrin was also compared under field conditions in Central Florida. Chlorantraniliprole was the most toxic compound tested (LC50 value of 4.5 ppm), followed by acephate (8.6 ppm), spinosad (31.1 ppm), clothianidin (46.6 ppm), bifenthrin (283 ppm) and Bacillus thuringiensis kurstaki, (342 ppm). In field tests, all compounds at label rates were effective (≥94% mortality of larvae exposed to fresh residues). However, a more rapid decline in activity of clothianidin and bifenthrin was observed compared with chlorantraniliprole. Clothianidin had no statistically detectable activity after 4 wk post-application in spring and the fall, and bifenthrin had no detectable activity after 3 wk in the spring and the fall. However, chlorantraniliprole maintained significant activity (≥84% mortality) compared with other treatments throughout the 5-wk study period. This study provides new information regarding the relative toxicities and persistence of current insecticides used for H. phaeopteralis and other turfgrass caterpillars. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Pesticide residues in canned foods, fruits, and vegetables: the application of Supercritical Fluid Extraction and chromatographic techniques in the analysis.

Science.gov (United States)

El-Saeid, Mohamed H

2003-12-11

Multiple pesticide residues have been observed in some samples of canned foods, frozen vegetables, and fruit jam, which put the health of the consumers at risk of adverse effects. It is quite apparent that such a state of affairs calls for the need of more accurate, cost-effective, and rapid analytical techniques capable of detecting the minimum concentrations of the multiple pesticide residues. The aims of this paper were first, to determine the effectiveness of the use of Supercritical Fluid Extraction (SFE) and Supercritical Fluid Chromatography (SFC) techniques in the analysis of the levels of pesticide residues in canned foods, vegetables, and fruits; and second, to contribute to the promotion of consumer safety by excluding pesticide residue contamination from markets. Fifteen different types of imported canned and frozen fruits and vegetables samples obtained from the Houston local food markets were investigated. The major types of pesticides tested were pyrethroids, herbicides, fungicides, and carbamates. By using these techniques, the overall data showed 60.82% of the food samples had no detection of any pesticide residues under this investigation. On the other hand, 39.15% different food samples were contaminated by four different pyrethroid residues +/- RSD% ranging from 0.03 +/- 0.005 to 0.05 +/- 0.03 ppm, of which most of the pyrethroid residues were detected in frozen vegetables and strawberry jam. Herbicide residues in test samples ranged from 0.03 +/- 0.005 to 0.8 +/- 0.01 ppm. Five different fungicides, ranging from 0.05 +/- 0.02 to 0.8 +/- 0.1 ppm, were found in five different frozen vegetable samples. Carbamate residues were not detected in 60% of investigated food samples. It was concluded that SFE and SFC techniques were accurate, reliable, less time consuming, and cost effective in the analysis of imported canned foods, fruits, and vegetables and are recommended for the monitoring of pesticide contaminations.

Short-tailed shrews: Toxicity and residue relationships of DDT, dieldrin, and endrin

Science.gov (United States)

Blus, L.J.

1978-01-01

Experiments involving dietary toxicity and residue relationships of DDT, dieldrin, and endrin were conducted with short-tailed shrews. Dietary concentrations of DDT dissolved in vegetable oils were usually more toxic than diets containing comparable amounts of powdered DDT. Younger shrews, particularly females, were more tolerant of powdered DDT than older animals; yet, there were no conspicuous age differences in toxicity of DDT dissolved in oils. In comparison to other mammals, short-tailed shrews are not unusually sensitive to DDT, dieldrin, or endrin on the basis of two-week feeding tests. The influence of age and sex on toxicity of DDT, endrin, and dieldrin was sometimes more important than body weight. Of those shrews of the same age and sex that were fed the same dietary dosage, heavier shrews were more tolerant than lighter individuals; and, heavier shrews tended to lose a greater percentage of body weight before death. There was a range of 15 to 105 DDT equivalents in brains of shrews dying on dietary dosages of DDT. Six shrews fed a high level of DDT seemed to have unusual metabolite capabilities and died with apparent lethal levels of DDD in their brains. Levels of dieldrin in brains of shrews that died on a dietary dosage of dieldrin ranged from 3.7 to 12.6 ppm. In the rates of gain and loss experiments where shrews were given diets containing 400 ppm DDT or 50 ppm dieldrin up to 17 days, high residues were noted in tissues of shrews after two weeks on a contaminated diet and a few died at that time. After shrews were placed on clean food, it was determined that >50% of the dieldrin residues in carcass and brain were lost in 50% of residues of DDT and metabolites in brains after 2 weeks on clean food; males lost nearly 50% of residues in carcasses after two weeks on clean food compared with a loss of only 11% in females.

Patch testing with methylchloroisothiazolinone/methylisothiazolinone 200 ppm aq. detects significantly more contact allergy than 100 ppm. A multicentre study within the European Environmental and Contact Dermatitis Research Group

DEFF Research Database (Denmark)

Bruze, Magnus; Isaksson, Marléne; Gruvberger, Birgitta

2014-01-01

, and that for IQ Chambers(®) was 25 µl. RESULTS: Contact allergy to MCI/MI at 100 and 200 ppm was found in 1.2% and 2.1% of patients, respectively (p more contact allergy than the presently used concentration of 100 ppm (dose...... 0.003 mg/cm(2)), without resulting in more adverse reactions. MCI/MI at 200 ppm should therefore be considered for inclusion in the European baseline test series....

Petroleum hydrocarbon residues in the marine environment of Bassein-Mumbai

International Nuclear Information System (INIS)

Chouksey, M.K.; Kadam, A.N.; Zingde, M.D.

2005-01-01

The paper reports PHc contamination in water, sediment and biota of the coastal area of Bassein-Mumbai in relation to relatively less polluted sites (Dabhol and Ratnagiri) off the west coast of India. To facilitate inter-comparison three standards have been used though the results are reported in terms of SAM (Residue of Saudi Arabian Mix crude). The concentration of PHc in water off Bassein-Mumbai varies widely (2.9-39.2 μg l -1 ) as compared to the average baseline (2.8 μgl -1 ) with higher values generally confined to creeks and estuaries. The higher concentration of PHc in the bottom water of shallow areas is attributed to the contribution from the sediment-associated petroleum residue. High concentration of PHc in the surficial sediment of inshore area Ratnagiri (107.7 ppm, dry wt) is perhaps the remnants of an oil spill that occurred in the Bombay High region on May 17, 1993. The majority of values of PHc concentration in the surficial sediment of the Bassein-Mumbai region exceed 15 ppm (dry wt) against the expected background ( -1 respectively is estimated for cores U11 and U12. Substantial increase in the concentration of PHc in sediment after 1950 in cores T8 and T10 correlates well with the establishment of refineries on the western shore of the Thane Creek in 1955-1960. A minor peak in most cores in the top 10 cm sediment probably results from biological transfer of PHc lower into the sediment by benthic organisms. Excess of PHc retained in the sediment of the Bassein-Mumbai region over the biogenic background is estimated at 40,000 t. The PHc residues (1.8-10.8 ppm, wet wt) in fish caught off Bassein-Mumbai do not suggest bioaccumulation. (author)

Transmitter and Translating Receiver Design For 64-ary Pulse Position Modulation (PPM)

Energy Technology Data Exchange (ETDEWEB)

Mendez, A J; Hernandez, V J; Gagliardi, R M; Bennett, C V

2010-01-20

This paper explores the architecture and design of an optically-implemented 64-ary PPM transmitter and direct-translating receiver that effectively translates incoming electrically-generated bit streams into optical PPM symbols (and vice-versa) at > 1 Gb/s data rates. The PPM transmitter is a cascade of optical switches operating at the frame rate. A corresponding receiver design is more difficult to architect and implement, since increasing data rates lead to correspondingly shorter decision times (slot times and frame times). We describe a solution in the form of a time-to-space mapping arrayed receiver that performs a translating algorithm represented as a code map. The technique for generating the code map is described, and the implementation of the receiver as a planar lightwave circuit is given. The techniques for implementing the transmitter and receiver can be generalized for any case of M-ary PPM.

Gas chromatographic determination with electron capture detection of residual ethylene oxide in intraocular lenses

Energy Technology Data Exchange (ETDEWEB)

Kikuchi, H.; Nakamura, A.; Tsuji, K.

1988-01-01

A sensitive method is described to determine trace quantities of ethylene oxide (EO) in EO-sterilized intraocular lenses (IOLs). An IOL is dipped in ethanol containing 0.25 ppm propylene oxide (PO) in a 4 mL vial, 2 drops of freshly distilled hydrobromic acid is added through a septum, and the mixture is warmed at 50/sup 0/C for 24 h. It is then neutralized by vigorous shaking with sodium bicarbonate, dehydrated with anhydrous sodium sulfate, and filtered. The filtrate is injected into a gas chromatograph with electron-capture detection, and the peak height ratio of ethylene bromohydrin/propylene bromohydrin is measured. EO residue is calculated from the calibration curve obtained through a similar procedure with the standard EO/PO solutions. The limit of determination is 0.04 ..mu..g/lens (ca 2.0 ppm). When EO residue levels were determined for IOLs sampled at 3 different aeration periods after stabilization, the authors found that 9 days of aeration was necessary to meet the US Food and Drug Administration proposed limit for EO residue in IOLs.

Bound residues of 14C-carbofuran and 14C-malathion in stored soybean seeds and their toxicological effects on mice

International Nuclear Information System (INIS)

Mahdy, F.; Taha, H.

2005-01-01

Soybeans treated with 1 4C -carbofuran or 1 4C -malathion at a dose of 30 mg/kg and stored for 30 weeks showed that the organophosphorus insecticide malathion had a higher binding tendency to soybean seeds than the carbamate insecticide carbofuran. The amount of malathion bound 1 4C -residues were almost three times higher (as percentage of applied dose) than carbofuran bound residues. Sub-chronic feeding experiments on mice for 90 days with a diet containing the bound 1 4C -residues at a dose of 0.91 and 2.39 ppm/day/mouse for carbofuran and malathion, respectively, caused non-significant symptoms of toxicity during the period of the experiment. A slight inhibition in plasma and erythrocyte choline esterase activities was observed during the second and third months in both treated mice fed on carbofuran or malathion. Liver enzymes, total protein, albumin, cholesterol, triglycerides and kidney functions showed non-significant differences from control values in case of mice fed on 1 4C -bound carbofuran residues. However, these mentioned blood parameters showed only slight increase, as compared with controls, in treated mice fed on 1 4C -bound malathion residues

Monocrotophpos and dicrotophos residues in birds as a result of misuse of organophosphates in Matagorda County, Texas

Science.gov (United States)

Flickinger, Edward L.; White, D.H.; Mitchell, C.A.; Lamont, T.G.

1984-01-01

About 1100 birds of 12 species died from organophosphate poisoning in Matagorda County on the Texas Gulf Coast in March and May 1982. Birds died from feeding on rice seed that was illegally treated with dicrotophos or monocrotophos and placed near rice fields as bait to attract and kill birds. Brain acetylcholinesterase inhibition of affected birds averaged 87% (range 82-89%), and contents of gastrointestinal tracts contained residues of dicrotophos (5.6-14 ppm) or monocrotophos (2.1-13 ppm). Rice seed collected at mortality sites contained 210 ppm dicrotophos or 950 ppm monocrotophos. Mortality from dicrotophos poisoning continued for almost 3 weeks. The practice of illegally treating rice seed with either of these 2 organophosphates appears to be infrequent but widespread at present.

The research of atmospheric 2D optical PPM CDMA system with turbo coding

Science.gov (United States)

Zhou, Xiuli; Li, Zaoxia

2007-11-01

The atmospheric two-dimensional optical code-division multiple-access (CDMA) systems using pulse-position modulation (PPM) and Turbo-coded were presented. We analyzed the bit-error rate (BER) of the proposed system using pulse-position modulation (PPM) with considering the effects of the scintillation, avalanche photodiode noise, thermal noise, and multi-user interference. We showed that the atmospheric two dimensional (2D) optical PPM CDMA systems can realize high-speed communications when the logarithm variance of the scintillation is less than 0.1, and the turbo-coded atmospheric optical CDMA system has better bit error rate(BER) performance than the atmospheric optical PPM CDMA systems without turbo-coded. We also showed that the turbo-coded system has better performance than the multi-user detection system.

Sensitivity Enhancement of a PPM Level Capacitive Moisture Sensor

Directory of Open Access Journals (Sweden)

Lokesh Kumar

2017-05-01

Full Text Available Measurement of moisture at ppm or ppb level is very difficult and the fabrication of such sensors at low cost is always challenging. High sensitivity is an important parameter for trace level (ppm humidity sensors. Anelectronic detection circuit for interfacing the humidity sensor with high sensitivity requires a simple hardware circuit with few active devices. The recent trends for increasing the sensitivity include fabricating nanoporous film with a very large surface area. In the present work, the sensitivity of a parallel plate capacitive type sensor with metal oxide sensing film has been significantly improved with an aim to detect moisture from 3 to 100 ppm in the industrial process gases used to fabricate semiconductors and other sensitive electronic devices. The sensitivity has been increased by (i fabricating a nanoporous film of aluminum oxide using the sol-gel method and (ii increasing the cross-sectional area of a parallel plate capacitor. A novel double sided capacitive structure has been proposed where two capacitors have been fabricated—one on the top and one on the bottom side of a flat alumina substrate—and then the capacitors are connected in parallel. The structure has twice the sensitivity of a single sensor in the same ppm range but the size of the structure remains unchanged. The important characteristics of the sensors such as the sensitivity (S = Δ C Δ p p m × 100 , the response time (tr, and the recovery time (tc are determined and compared with a commercial SHAW, UKdew point meter. The fabricated double sided sensor has comparable sensitivity (S = 100%, tr (s = 28, tc (s = 40 with the commercial meter (S = 100.5%, tr (s = 258 but has a faster response time. The proposed method of sensitivity enhancement is simple, and mass producible.

Simulating Rayleigh-Taylor (RT) instability using PPM hydrodynamics @scale on Roadrunner (u)

Energy Technology Data Exchange (ETDEWEB)

Woodward, Paul R [Los Alamos National Laboratory; Dimonte, Guy [Los Alamos National Laboratory; Rockefeller, Gabriel M [Los Alamos National Laboratory; Fryer, Christopher L [Los Alamos National Laboratory; Dimonte, Guy [Los Alamos National Laboratory; Dai, W [Los Alamos National Laboratory; Kares, R. J. [Los Alamos National Laboratory

2011-01-05

The effect of initial conditions on the self-similar growth of the RT instability is investigated using a hydrodynamics code based on the piecewise-parabolic-method (PPM). The PPM code was converted to the hybrid architecture of Roadrunner in order to perform the simulations at extremely high speed and spatial resolution. This paper describes the code conversion to the Cell processor, the scaling studies to 12 CU's on Roadrunner and results on the dependence of the RT growth rate on initial conditions. The relevance of the Roadrunner implementation of this PPM code to other existing and anticipated computer architectures is also discussed.

DETECTION OF LASALOCID RESIDUES IN THE TISSUES OF BROILER CHICKENS BY A NEW SCREENING TEST TOTAL ANTIBIOTICS

Directory of Open Access Journals (Sweden)

Martin Levkut, ml.

2011-04-01

Full Text Available The aim of the present study was to evaluate the microbial growth inhibition test Total antibiotics for the screening of lasalocid residues in the tissues of broiler chickens after its oral administration in medicated feed. The residues were investigated throughout the 5-day withdrawal period /WP/ and also on day 6 representing the first day following the WP. All broiler chicken tissues were positive for lasalocid. The breast muscle was positive (the presence of residues at/above the detection limit /LOD/ of method up to day 1 of the WP, the thigh muscle, gizzard, heart, skin and fat up to day 3 of the WP and the liver and kidneys up to day 4 of the WP. When evaluating the dubious results (the presence of residues just below the LOD of method, the breast muscle was suspect positive up to day 3 of the WP and the gizzard, skin and fat up to day 4 of the WP. No positive or dubious results were detected on day 5 of the WP. The LOD of Bacillus stearothermophilus var. calidolactis for maduramycin was 500 µg.l-1.doi:10.5219/140

Measurement of the negative muon anomalous magnetic moment to 0.7 ppm

NARCIS (Netherlands)

Bennett, GW; Bousquet, B; Brown, HN; Bunce, G; Carey, RM; Cushman, P; Danby, GT; Debevec, PT; Deile, M; Deng, H; Dhawan, SK; Druzhinin, VP; Duong, L; Farley, FJM; Fedotovich, GV; Gray, FE; Grigoriev, D; Grosse-Perdekamp, M; Grossmann, A; Hare, MF; Hertzog, DW; Huang, [No Value; Hughes, VW; Iwasaki, M; Jungmann, K; Kawall, D; Khazin, BI; Krienen, F; Kronkvist, [No Value; Lam, A; Larsen, R; Lee, YY; Logashenko, [No Value; McNabb, R; Meng, W; Miller, JP; Morse, WM; Nikas, D; Onderwater, CJG; Orlov, Y; Ozben, CS; Paley, JM; Peng, Q; Polly, CC; Pretz, J; Prigl, R; Putlitz, GZ; Qian, T; Redin, SI; Rind, O; Roberts, BL; Ryskulov, N; Semertzidis, YK; Shagin, P; Shatunov, YM; Sichtermann, EP; Solodov, E; Sossong, M; Sulak, LR; Trofimov, A; von Walter, P; Yamamoto, A; Huang, X; Kronkvist, I.; Logashenko, I.; Özben, C.S.; Polley, C.C.; Shatunov, Yu.M.; von Walter, R.

2004-01-01

The anomalous magnetic moment of the negative muon has been measured to a precision of 0.7 ppm (ppm) at the Brookhaven Alternating Gradient Synchrotron. This result is based on data collected in 2001, and is over an order of magnitude more precise than the previous measurement for the negative muon.

21 CFR 556.720 - Tetracycline.

Science.gov (United States)

2010-04-01

..., FEEDS, AND RELATED PRODUCTS TOLERANCES FOR RESIDUES OF NEW ANIMAL DRUGS IN FOOD Specific Tolerances for Residues of New Animal Drugs § 556.720 Tetracycline. (a) Acceptable daily intake (ADI). The ADI for total... tissues of calves, swine, sheep, chickens, and turkeys, of 2 parts per million (ppm) in muscle, 6 ppm in...

Receiver Architecture for 12.5 Gb/s 16-ary Pulse Position Modulation (PPM) Signaling

Energy Technology Data Exchange (ETDEWEB)

Mendez, A J; Gagliardi, R M; Hernandez, V J; Bennett, C V

2008-07-11

PPM is a signaling scheme that enables the transmission of multiple bits per symbol [1]. It has found favor in the regime of free space optical communications ('FSO' or 'Lasercom'); however, PPM has yet to be widely applied to fiber optic-based communications. Its limitation in fiber results from the exceedingly high bandwidth requirements needed to electronically process a directly detected pulse, especially as the symbol rate increases and the pulse width correspondingly decreases. As a solution, we introduced the concept of a virtual quadrant receiver for receiving 1.25 Gb/s 4-ary PPM, where photonic processing reduced the number of required electronic components [2]. In this paper, we extend these photonic process techniques to a 16-ary, 12.5 Gb/s (10 Gb/s plus 8B/10B line coding) PPM communications system for fiber optic avionics, wherein much of the receiver processing is enabled by techniques based on planar lightwave circuits (PLCs). The architecture is applicable to higher input data rates and M-ary PPM. In the following, we present the PPM encoding and decoding architectures and numerically simulated results.

Cost and cost-effectiveness of PPM-DOTS for tuberculosis control: evidence from India.

OpenAIRE

Floyd, Katherine; Arora, V. K.; Murthy, K. J. R.; Lonnroth, Knut; Singla, Neeta; Akbar, Y.; Zignol, Matteo; Uplekar, Mukund

2006-01-01

OBJECTIVE: To assess the cost and cost-effectiveness of the Public-Private Mix DOTS (PPM-DOTS) strategy for tuberculosis (TB) control in India. METHODS: We collected data on the costs and effects of pilot PPM-DOTS projects in Delhi and Hyderabad using documentary data and interviews. The cost of PPM-DOTS was compared with public sector DOTS (i.e. DOTS delivered through public sector facilities only) and non-DOTS treatment in the private sector. Costs for 2002 in US$ were assessed for the publ...

Pesticide Residues in Canned Foods, Fruits, and Vegetables: The Application of Supercritical Fluid Extraction and Chromatographic Techniques in the Analysis

Directory of Open Access Journals (Sweden)

Mohamed H. EL-Saeid

2003-01-01

Full Text Available Multiple pesticide residues have been observed in some samples of canned foods, frozen vegetables, and fruit jam, which put the health of the consumers at risk of adverse effects. It is quite apparent that such a state of affairs calls for the need of more accurate, cost-effective, and rapid analytical techniques capable of detecting the minimum concentrations of the multiple pesticide residues. The aims of this paper were first, to determine the effectiveness of the use of Supercritical Fluid Extraction (SFE and Supercritical Fluid Chromatography (SFC techniques in the analysis of the levels of pesticide residues in canned foods, vegetables, and fruits; and second, to contribute to the promotion of consumer safety by excluding pesticide residue contamination from markets. Fifteen different types of imported canned and frozen fruits and vegetables samples obtained from the Houston local food markets were investigated. The major types of pesticides tested were pyrethroids, herbicides, fungicides, and carbamates.By using these techniques, the overall data showed 60.82% of the food samples had no detection of any pesticide residues under this investigation. On the other hand, 39.15% different food samples were contaminated by four different pyrethroid residues ± RSD% ranging from 0.03 ± 0.005 to 0.05 ± 0.03 ppm, of which most of the pyrethroid residues were detected in frozen vegetables and strawberry jam. Herbicide residues in test samples ranged from 0.03 ± 0.005 to 0.8 ± 0.01 ppm. Five different fungicides, ranging from 0.05 ± 0.02 to 0.8 ±0.1 ppm, were found in five different frozen vegetable samples. Carbamate residues were not detected in 60% of investigated food samples. It was concluded that SFE and SFC techniques were accurate, reliable, less time consuming, and cost effective in the analysis of imported canned foods, fruits, and vegetables and are recommended for the monitoring of pesticide contaminations.

Performance Analysis of SAC Optical PPM-CDMA System-Based Interference Rejection Technique

Science.gov (United States)

Alsowaidi, N.; Eltaif, Tawfig; Mokhtar, M. R.

2016-03-01

In this paper, we aim to theoretically analyse optical code division multiple access (OCDMA) system that based on successive interference cancellation (SIC) using pulse position modulation (PPM), considering the interference between the users, imperfection cancellation occurred during the cancellation process and receiver noises. Spectral amplitude coding (SAC) scheme is used to suppress the overlapping between the users and reduce the receiver noises effect. The theoretical analysis of the multiple access interference (MAI)-limited performance of this approach indicates the influence of the size of M-ary PPM on OCDMA system. The OCDMA system performance improves with increasing M-ary PPM. Therefore, it was found that the SIC/SAC-OCDMA system using PPM technique along with modified prime (MPR) codes used as signature sequence code offers significant improvement over the one without cancellation and it can support up to 103 users at the benchmarking value of bit error rate (BER) = 10-9 with prime number p = 11 while the system without cancellation scheme can support only up to 52 users.

Decomposition of rice residue in tropical soils, 2

International Nuclear Information System (INIS)

Yoneyama, Tadakatsu; Yoshida, Tomio

1977-01-01

The decomposition processes of intact rice residue (leaf blades) in the Maahas soil in the Philippines were investigated. Three sets of beakers simulating both lowland and upland conditions were incubated in the dark at 30 deg. C. One set of beakers had neither rice residue nor fertilizer. Pieces of leaf blades weighing 204 mg (dry weight) were inserted in the second set. Pieces of leaf blades were inserted in the third set, and 200 ppm of fertilizer nitrogen as 15 N-labelled ammonium sulfate was added. The experiment dealt with the nitrogen immobilization by rice residue under lowland and upland conditions. The rice residue which has contained low nitrogen absorbed nitrogen from the soil and from the added fertilizer (ammonium sulfate) during its decomposition under both conditions. Under the lowland condition, the amount of nitrogen immobilized was small during the first week, but became large after 2 or 3 weeks. Under the upland condition, the immobilized nitrogen reached its maximum during the first week, but the amount was not so large as that under the lowland condition. The added fertilizer stimulated the decrease of weight of the rice residue in the early incubation period, but retarded it later under both conditions. The absorption of fertilizer by the rice residue ceased at the early stage of residue decomposition, but the nitrogen content of the residue continued to increase. (Iwakiri, K.)

Low-Power-Consumption Integrated PPM Laser Transmitter, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Conventional PPM laser transmitters, a CW laser followed by a modulator, are inherently inefficient since the data must be carved from the laser's steady output. 95%...

Low-Power-Consumption Integrated PPM Laser Transmitter, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Conventional PPM laser transmitters, a CW laser followed by a modulator, are inherently inefficient since the data must be carved from the laser's steady output. 95%...

Multivessel supercritical fluid extraction of food items in Total Diet Study.

Science.gov (United States)

Hopper, M L; King, J W; Johnson, J H; Serino, A A; Butler, R J

1995-01-01

An off-line, large capacity, multivessel supercritical fluid extractor (SFE) was designed and constructed for extraction of large samples. The extractor can simultaneously process 1-6 samples (15-25 g) by using supercritical carbon dioxide (SC-CO2), which is relatively nontoxic and nonflammable, as the solvent extraction medium. Lipid recoveries for the SFE system were comparable to those obtained by blending or Soxhlet extraction procedures. Extractions at 10,000 psi, 80 degrees C, expanded gaseous CO2 flow rates of 4-5 L/min (35 degrees C), and 1-3 h extraction times gave reproducible lipid recoveries for pork sausage (relative standard deviation [RSD], 1.32%), corn chips (RSD, 0.46%), cheddar cheese (RSD, 1.14%), and peanut butter (RSD, 0.44%). In addition, this SFE system gave reproducible recoveries (> 93%) for butter fortified with cis-chlordane and malathion at the 100 ppm and 0.1 ppm levels. Six portions each of cheddar cheese, saltine crackers, sandwich cookies, and ground hamburger also were simultaneously extracted with SC-CO2 and analyzed for incurred pesticide residues. Results obtained with this SFE system were reproducible and comparable with results from organic-solvent extraction procedures currently used in the Total Diet Study; therefore, use and disposal of large quantities of organic solvents can be eliminated.

Persistence of malathion residues in stored milled rice: Direct and indirect applications

International Nuclear Information System (INIS)

Arshad, J.H.

1990-01-01

Two experiments were carried out: (i) to study the persistence of malathion residues in stored milled rice following multiple applications of 14 C-malathion to the bagged rice and (ii) to determine the degradation of malathion in stored milled rice and stored paddy following direct and single application of 14 C-malathion. The storage conditions were similar to those found in the local rice godowns. Three applications of malathion to the bagged milled rice resulted in the accumulation of malathion and its metabolites in and/or on the rice grains over the storage period. After 9 months' storage, ca. 4% of the total applied radioactivity, which amounted to 10 μg/g equivalent of 14 C residues, were found in and/or on the grains. About one fourth of the residue remained as the unchanged parent compound. On the other hand, when 14 C-malathion at the 10 ppm level was mixed directly with the milled rice or paddy prior to storage, the amount of malathion (recovered in the chloroform extracts) decreased from 6.2 μg/g at zero time to 2.9 μg/g after 3 months' storage for the milled rice samples. The major metabolite in the milled rice and paddy samples was malathion monocarboxylic acid with trace amounts of malathion dicarboxylic acid and malaoxon. (author). 5 refs, 3 tabs

Effects on health, performance, and tissue residues of the ionophore antibiotic salinomycin in finishing broilers (21 to 38 d).

Science.gov (United States)

Diaz, Gonzalo J; Aguillón, Yandy; Cortés, Amparo

2018-06-01

A study was conducted to evaluate the effects of feeding salinomycin at the recommended prophylactic level, and at 2 and 3 times this level, to finishing male broilers (d 21 to 38). Four treatment groups were given the experimental diets containing 0, 60, 120, or 180 parts per million (ppm) salinomycin from d 21 to 38. Performance, relative organ weights, selected serum enzymes, and salinomycin residues in liver, muscle, and serum were determined. Salinomycin supplementation had no effect on body weight, feed intake, or feed conversion, and caused no overt signs of toxicity. After a week of being fed the salinomycin diets, the serum activity of aspartate aminotransferase was significantly increased in chickens fed 180 ppm compared with controls. These birds also showed microscopic lesions in breast and thigh muscles, but not in cardiac muscle. Salinomycin residues were not detected by high-performance liquid chromatography coupled to tandem mass spectrometry in liver or muscle samples from the birds fed 0, 60, or 120 ppm salinomycin. However, chickens fed 180 ppm salinomycin had detectable levels in liver and muscle above the maximum residue level of 5 μg/kg established by the European Union. All birds fed salinomycin had salinomycin in their sera with levels ranging from N.D. (not detected) in the controls to 24.4 ± 7.9, 61.4 ± 18.9, and 94.5 ± 9.1 μg/L for salinomycin dietary levels of 60, 120, and 180 ppm, respectively. Serum salinomycin concentration was linearly related with salinomycin content in feed (y = 0.584x - 10, r2 = 0.999). The results showed that even at 3 times the prophylactic level, salinomycin does not induce clinical toxicosis or mortality. No salinomycin residues were found in edible tissues at the recommended dietary level or at 2 times this level. However, salinomycin was detected in serum regardless of the dietary level. A simple method for salinomycin determination in serum is described which can be used as a marker of exposure

Effect of cooking on14 C-tetrachlorvinphos residues in faba beans

International Nuclear Information System (INIS)

Farghaly, M.; Zayed, S.M.A.D.

1986-01-01

The effect of cooking on 14 C-tetrachlorvinphos in stored vicia faba beans was studied. The results indicated that over 50% of the dose originally present inside the grains (37 ppm), could be recovered in the aqueous extract of the cooked grains. Considerable portion of radioactivity (About 22%) was associated with the grains in a non-extractable from. Residues in cooked beans included, in addition to a small amount of the parent insecticide, desmethyl tetrachlorvinphos, mono methyl phosphate and dimethyl phosphate. The results obtained indicate that tetrachlorvinphos residues are not appreciably affected by cooking. 1 tab

Successive Interference Cancellation for DS-Optical PPM-CDMA Systems

Science.gov (United States)

Alsowaidi, N.; Eltaif, Tawfig; Mokhtar, M. R.

2016-06-01

In this paper we introduce a successive interference cancellation (SIC) scheme for direct sequence optical code division multiple access (DS-OCDMA) systems using pulse position modulation (PPM). Considering double-padded modified prime code (DPMPC) as a signature sequence code, results show that the system has better performance in terms of both capacity and bit error rate (BER) as compared to the one without cancellation scheme, where the system with SIC scheme can support up to 88 users while the system without SIC scheme can support only 38 users at similar BER=10-9. Although the receiver sensitivity is affected by the overlapping between users, which limits the system performance, the theoretical analysis of this issue indicates the influence of the size of M-ary PPM on OCDMA system. Hence, the BER value is still sufficient for good system performance.

A Simple Surface-Enhanced Raman Spectroscopic Method for on-Site Screening of Tetracycline Residue in Whole Milk

Directory of Open Access Journals (Sweden)

Sagar Dhakal

2018-02-01

Full Text Available Therapeutic and subtherapeutic use of veterinary drugs has increased the risk of residue contamination in animal food products. Antibiotics such as tetracycline are used for mastitis treatment of lactating cows. Milk expressed from treated cows before the withdrawal period has elapsed may contain tetracycline residue. This study developed a simple surface-enhanced Raman spectroscopic (SERS method for on-site screening of tetracycline residue in milk and water. Six batches of silver colloid nanoparticles were prepared for surface enhancement measurement. Milk-tetracycline and water-tetracycline solutions were prepared at seven concentration levels (1000, 500, 100, 10, 1, 0.1, and 0.01 ppm and spiked with silver colloid nanoparticles. A 785 nm Raman spectroscopic system was used for spectral measurement. Tetracycline vibrational modes were observed at 1285, 1317 and 1632 cm−1 in water-tetracycline solutions and 1322 and 1621 cm−1 (shifted from 1317 and 1632 cm−1, respectively in milk-tetracycline solutions. Tetracycline residue concentration as low as 0.01 ppm was detected in both the solutions. The peak intensities at 1285 and 1322 cm−1 were used to estimate the tetracycline concentrations in water and milk with correlation coefficients of 0.92 for water and 0.88 for milk. Results indicate that this SERS method is a potential tool that can be used on-site at field production for qualitative and quantitative detection of tetracycline residues.

A Simple Surface-Enhanced Raman Spectroscopic Method for on-Site Screening of Tetracycline Residue in Whole Milk.

Science.gov (United States)

Dhakal, Sagar; Chao, Kuanglin; Huang, Qing; Kim, Moon; Schmidt, Walter; Qin, Jianwei; Broadhurst, C Leigh

2018-02-01

Therapeutic and subtherapeutic use of veterinary drugs has increased the risk of residue contamination in animal food products. Antibiotics such as tetracycline are used for mastitis treatment of lactating cows. Milk expressed from treated cows before the withdrawal period has elapsed may contain tetracycline residue. This study developed a simple surface-enhanced Raman spectroscopic (SERS) method for on-site screening of tetracycline residue in milk and water. Six batches of silver colloid nanoparticles were prepared for surface enhancement measurement. Milk-tetracycline and water-tetracycline solutions were prepared at seven concentration levels (1000, 500, 100, 10, 1, 0.1, and 0.01 ppm) and spiked with silver colloid nanoparticles. A 785 nm Raman spectroscopic system was used for spectral measurement. Tetracycline vibrational modes were observed at 1285, 1317 and 1632 cm -1 in water-tetracycline solutions and 1322 and 1621 cm -1 (shifted from 1317 and 1632 cm -1 , respectively) in milk-tetracycline solutions. Tetracycline residue concentration as low as 0.01 ppm was detected in both the solutions. The peak intensities at 1285 and 1322 cm -1 were used to estimate the tetracycline concentrations in water and milk with correlation coefficients of 0.92 for water and 0.88 for milk. Results indicate that this SERS method is a potential tool that can be used on-site at field production for qualitative and quantitative detection of tetracycline residues.

Total sulfur determination in residues of crude oil distillation using FT-IR/ATR and variable selection methods

Science.gov (United States)

Müller, Aline Lima Hermes; Picoloto, Rochele Sogari; Mello, Paola de Azevedo; Ferrão, Marco Flores; dos Santos, Maria de Fátima Pereira; Guimarães, Regina Célia Lourenço; Müller, Edson Irineu; Flores, Erico Marlon Moraes

2012-04-01

Total sulfur concentration was determined in atmospheric residue (AR) and vacuum residue (VR) samples obtained from petroleum distillation process by Fourier transform infrared spectroscopy with attenuated total reflectance (FT-IR/ATR) in association with chemometric methods. Calibration and prediction set consisted of 40 and 20 samples, respectively. Calibration models were developed using two variable selection models: interval partial least squares (iPLS) and synergy interval partial least squares (siPLS). Different treatments and pre-processing steps were also evaluated for the development of models. The pre-treatment based on multiplicative scatter correction (MSC) and the mean centered data were selected for models construction. The use of siPLS as variable selection method provided a model with root mean square error of prediction (RMSEP) values significantly better than those obtained by PLS model using all variables. The best model was obtained using siPLS algorithm with spectra divided in 20 intervals and combinations of 3 intervals (911-824, 823-736 and 737-650 cm-1). This model produced a RMSECV of 400 mg kg-1 S and RMSEP of 420 mg kg-1 S, showing a correlation coefficient of 0.990.

Organochlorine residues and shell thicknesses in eggs of the clapper rail, common gallinule, purple gallinule, and limpkin (class Aves), eastern and southern United States, 1972-74.

Science.gov (United States)

Klaas, E E; Ohlendorf, H M; Cromartie, E

1980-12-01

Organochlorine residues and shell thicknesses were surveyed in eggs of the clapper rail (Rallus longirostris), purple gallinule (Porphyrula martinica), common gallinule (Gallinula chloropas), and limpkin (Aramus guarauna) from the eastern and southern United States. Clapper rail eggs were collected during 1972-73 in New Jersey, Virginia, and South Carolina. During 1973-74, gallinule eggs were collected in Florida, South Carolina, and Louisiana, and limpkin eggs were collected in Florida. Egg contents were analyzed for residues of organochlorine pesticides, including DDT, TDE, DDE, dieldrin, mirex, heptachlor epoxide, oxychlordane, cis-chlordane (and/or trans-nonachlor), cis-nonachlor, hexachlorobenzene (HCB), toxaphene, and endrin, and for polychlorinated biphenyls (PCBs). Shell thicknesses of recent eggs of these species were compared with archival eggs that had been collected before 1947. With the exception of the limpkin, the majority of eggs analyzed contained residues of p,p'-DDE and PCBs. Geometric means ranged from 0.10 ppm to 1.3 ppm. Small amounts (less than 1.0 ppm) of mirex, dieldrin, cis-chlordane (and/or trans-nonachlor), TDE, and DDT were detected in a few eggs. No evidence of eggshell thinning was found for any of the species studied. DDE residues in clapper rail eggs were higher in New Jersey and Virginia than in South Carolina.

Organochlorine residues and shell thickness in eggs of the clapper rail, common gallinule, purple gallinule, and limpkin (Class Aves), eastern and southern United States, 1972-74

Science.gov (United States)

Klaas, E.E.; Ohlendorf, H.M.; Cromartie, E.

1980-01-01

Organochlorine residues and shell thicknesses were surveyed in eggs of the clapper rail (Rallus longirostris), purple gallinule (Porphyrula martinica), common gallinule (Gallinula chloropas), and limpkin (Aramus guarauna) from the eastern and southern United States. Clapper rail eggs were collected during 1972-73 in New Jersey, Virginia, and South Carolina. During 1973-74, gallinule eggs were collected in Florida, South Carolina, and Louisiana, and limpkin eggs were collected in Florida. Egg contents were analyzed for residues of organochlorine pesticides, including DDT, TDE, DDE, dieldrin, mirex, heptachlor epoxide, oxychlordane, cis-chlordane (and/or trans-nonachlor), cis-nonachlor, hexachlorobenzene (HCB), toxaphene, and endrin, and for polychlorinated biphenyls (PCBs). Shell thicknesses of recent eggs of these species were compared with archival eggs that had been collected before 1947. With the exception of the limpkin, the majority of eggs analyzed contained residues of p,p'-DDE and PCBs. Geometric means ranged from 0.10 ppm to 1.3 ppm. Small amounts (less than 1.0 ppm) of mirex, dieldrin, cis-chlordane (and/or trans-nonachlor), TDE, and DDT were detected in a few eggs. No evidence of eggshell thinning was found for any of the species studied. DDE residues in clapper rail eggs were higher in New Jersey and Virginia than in South Carolina.

Study on recovering directly the commercial cerium oxide and total of residue rare earths from Dongpao bastnasite concentrate

International Nuclear Information System (INIS)

Nguyen Trong Hung; Nguyen Thanh Chung; Luu Xuan Dinh

2003-01-01

A technology for decomposition roasting and sequential leaching processes of Dong Pao bastnasite concentrate to recover directly commercial cerium oxide and total of residue rare earth elements from the leaching solution of the roasted product have been investigated. The bastnasite concentrate is initially roasted at temperature range of 600 - 650 degC and for time of 4 hrs in order to decompose and convert the hardly soluble carbonate forms of ore into easily soluble oxide. The roasted solid is then leached with sulfuric acid solution of 6N at 60 degC for 4 hrs to convert rare earths in oxide and fluoride form into rare earth sulfate. The recovery yield of rare earths of these stages is more than 95%. The attention has especially been paid on recovering directly the commercial cerium oxide and total of residue rare earth element from the above leaching solution. Complex ions of CeSO 4 2+ , Ce(SO 4 ) 2 , Ce(SO 4 ) 3 2- and Ce(SO 4 ) 4 4- exist in aqueous solution of cerium (IV) sulfate. Based on the property, the method of ion - sieve with DOWEX cation resin column has been applied to estimating separation of the ceric complex anions from Ln(III). The survey showed that most of the ceric complex anions are separated from total of residue rare earths. The latter which are absorbed in the cation column are recovered by elution of HCl of 4N. The recovery yield of cerium can only be reached 20% but the purity of that is very high, can be reached 99.6%. About 5 kg of CeO 2 of high grade and 5 kg of TREO of commercial specification have been produced. (author)

Antioxidant Effect of Extracts from the Coffee Residue in Raw and Cooked Meat

Directory of Open Access Journals (Sweden)

Ji-Hee Kim

2016-07-01

Full Text Available The residue of ground coffee obtained after the brewing process (spent coffee still contains various functional components with high antioxidant capacity and health benefits, but no attempts have been made to use it as a resource to produce value-added food ingredients. This study evaluates the antioxidant activity of ethanol or hot water extracts from the residues of coffee after brewing. An extraction experiment was carried out using the conventional solid–liquid methods, including ethanol and water as the extraction media at different temperatures and liquid/solid ratios. The antioxidant activity of extracts was tested for total phenolic compound (TPC, 2,2-diphenyl-1-picrylhydrazyl (DPPH, and 2-thiobarbituric acid reactive substances (TBARS using oil emulsion and raw/cooked meat systems. The DPPH radical scavenging activity of the ethanol extracts with heating (HEE and without heating (CEE were higher than that of the hot water extracts (WE. The highest DPPH value of HEE and CEE at 1000 ppm was 91.22% and 90.21%, respectively. In oil emulsion and raw/cooked systems, both the water and ethanol extracts had similar antioxidant effects to the positive control (BHA, but HEE and CEE extracts showed stronger antioxidant activities than WE extract. These results indicated that the ethanol extracts of coffee residue have a strong antioxidant activity and have the potential to be used as a natural antioxidant in meat.

Chlortetracycline and Oxytetracycline Residues in Poultry Tissues and Eggs

Science.gov (United States)

Meredith, W. E.; Weiser, H. H.; Winter, A. R.

1965-01-01

A pad-plate method of assaying residual amounts of chlortetracycline (CTC) and oxytetracycline (OTC) using Bacillus cereus 213 was used to determine amounts of antibiotic left in tissues and eggs of poultry fed 1,000 and 200 ppm of CTC and OTC in basal feed mixtures. The effects of various methods of cooking the tissues and eggs and the potentiating effect of terephthalic acid (TPA) were studied. It was found that normal methods of roasting, frying, and autoclaving poultry tissue destroyed all residual CTC and OTC, even with the potentiating effect of TPA. The largest amounts of residual antibiotic were found in the liver, then breast, and then thigh tissue when assayed for CTC. Tissue assays for CTC revealed that it was not taken up as extensively as CTC and the largest amounts were found in the liver, then breast. OTC residue was seldom found in the thigh tissue. Terephthalic acid in 0.5% concentration increased the concentration found in all cases. Cooking by poaching and scrambling eggs did not destroy the antibiotic in all cases. PMID:14264853

Optimisation of recovery protocols for double-base smokeless powder residues analysed by total vaporisation (TV) SPME/GC-MS.

Science.gov (United States)

Sauzier, Georgina; Bors, Dana; Ash, Jordan; Goodpaster, John V; Lewis, Simon W

2016-09-01

The investigation of explosive events requires appropriate evidential protocols to recover and preserve residues from the scene. In this study, a central composite design was used to determine statistically validated optimum recovery parameters for double-base smokeless powder residues on steel, analysed using total vaporisation (TV) SPME/GC-MS. It was found that maximum recovery was obtained using isopropanol-wetted swabs stored under refrigerated conditions, then extracted for 15min into acetone on the same day as sample collection. These parameters were applied to the recovery of post-blast residues deposited on steel witness surfaces following a PVC pipe bomb detonation, resulting in detection of all target components across the majority of samples. Higher overall recoveries were obtained from plates facing the sides of the device, consistent with the point of first failure occurring in the pipe body as observed in previous studies. The methodology employed here may be readily applied to a variety of other explosive compounds, and thus assist in establishing 'best practice' procedures for explosive investigations. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of commercial processing procedures on 14C-LINDANE residues in corn oil

International Nuclear Information System (INIS)

Soliman, S.M.

2006-01-01

At blooming, maize plants were sprayed twice, 23 days apart, at a dose of 22 mg equivalent to 5 μCi/ plant. At post harvest, maize seeds had a radioactivity corresponding to 0.36% of the applied dose. The insecticide residues in crude oil, cake and methanolic extract were amounted to 8 % and 60 % 5 % , respectively, of original residues inside the seeds.The 14 C-activity in the crude oil could be reduced by commercial processes locally used for refining. The refined oil had a residue level of about 0.7 ppm mainly in the form of unchanged lindane in addition to a number of chloro phenols as main metabolites. Refining of corn oil fortified with 14 C-lindane led to a high reduction of 14 C-lindane (88%). The refined oil contained a residue consisting lindane and its chloro phenols

Mesh Excision: Is Total Mesh Excision Necessary?

Science.gov (United States)

Wolff, Gillian F; Winters, J Christian; Krlin, Ryan M

2016-04-01

Nearly 29% of women will undergo a secondary, repeat operation for pelvic organ prolapse (POP) symptom recurrence following a primary repair, as reported by Abbott et al. (Am J Obstet Gynecol 210:163.e1-163.e1, 2014). In efforts to decrease the rates of failure, graft materials have been utilized to augment transvaginal repairs. Following the success of using polypropylene mesh (PPM) for stress urinary incontinence (SUI), the use of PPM in the transvaginal repair of POP increased. However, in recent years, significant concerns have been raised about the safety of PPM mesh. Complications, some specific to mesh, such as exposures, erosion, dyspareunia, and pelvic pain, have been reported with increased frequency. In the current literature, there is not substantive evidence to suggest that PPM has intrinsic properties that warrant total mesh removal in the absence of complications. There are a number of complications that can occur after transvaginal mesh placement that do warrant surgical intervention after failure of conservative therapy. In aggregate, there are no high-quality controlled studies that clearly demonstrate that total mesh removal is consistently more likely to achieve pain reduction. In the cases of obstruction and erosion, it seems clear that definitive removal of the offending mesh is associated with resolution of symptoms in the majority of cases and reasonable practice. There are a number of complications that can occur with removal of mesh, and patients should be informed of this as they formulate a choice of treatment. We will review these considerations as we examine the clinical question of whether total versus partial removal of mesh is necessary for the resolution of complications following transvaginal mesh placement.

Simultaneous screening and confirmation of multiple classes of drug residues in fish by liquid chromatography-ion trap mass spectrometry.

Science.gov (United States)

Smith, Shani; Gieseker, Charles; Reimschuessel, Renate; Decker, Christie-Sue; Carson, Mary C

2009-11-13

LC-ion trap mass spectrometry was used to screen and confirm 38 compounds from a variety of drug classes in four species of fish: trout, salmon, catfish, and tilapia. Samples were extracted with acetonitrile and hexane. The acetonitrile phase was evaporated, redissolved in water and acetonitrile, and analyzed by gradient chromatography on a phenyl column. MS(2) or MS(3) spectra were monitored for each compound. Qualitative method performance was evaluated by the analysis over several days of replicate samples of control fish, fish fortified with a drug mixture at 1 ppm, 0.1 ppm and 0.01 ppm, and fish dosed with a representative from each drug class. Half of the 38 drugs were confirmed at 0.01 ppm, the lowest fortification level. This included all of the quinolones and fluoroquinolones, the macrolides, malachite green, and most of the imidazoles. Florfenicol amine, metronidazole, sulfonamides, tetracyclines, and most of the betalactams were confirmed at 0.1 ppm. Ivermectin and penicillin G were only detectable in the 1 ppm fortified samples. With the exception of amoxicillin, emamectin, metronidazole, and tylosin, residue presence was confirmed in all the dosed fish.

STABILIZATION OF A MIXED WASTE SLUDGE SURROGATE CONTAINING MORE THAN 260 PPM MERCURY

International Nuclear Information System (INIS)

Smith, W. J.; Feizollahi, F.; Brimley, R.

2002-01-01

In an earlier demonstration of an innovative mercury stabilization technology for the Department of Energy, ATG's full-scale process stabilized mercury in soils that initially contained more than 260 ppm of mercury of unknown speciation. The treated waste satisfied the leaching standards for mercury that qualify wastes containing less than 260 ppm for land disposal. This paper describes the extension of that work to demonstrate a full-scale process for the stabilization of a representative sludge that contained more than 260 ppm of Hg of several mercury species. RCRA (Resource Conservation and Recovery Act) regulations now require the recovery of mercury from any waste containing more than 260 ppm of mercury, usually with thermal retorts. The results of this work with a surrogate sludge, and of the previous work with an actual soil, support a proposal now before the U.S. EPA (Environmental Protection Agency) to allow such wastes to be stabilized without retorting. The full-scale demonstration with a sulfide reagent reduced the mercury concentrations in extracts of treated sludge below the relevant leaching standard, a Universal Treatment Standard (UTS) limit of 0.025 mg mercury per liter of leachate generated by the Toxicity Characteristic Leaching Procedure (TCLP). The sulfide formulation reduced the concentration to about onehalf the UTS limit

The coral reef crisis: the critical importance of<350 ppm CO2.

Science.gov (United States)

Veron, J E N; Hoegh-Guldberg, O; Lenton, T M; Lough, J M; Obura, D O; Pearce-Kelly, P; Sheppard, C R C; Spalding, M; Stafford-Smith, M G; Rogers, A D

2009-10-01

Temperature-induced mass coral bleaching causing mortality on a wide geographic scale started when atmospheric CO(2) levels exceeded approximately 320 ppm. When CO(2) levels reached approximately 340 ppm, sporadic but highly destructive mass bleaching occurred in most reefs world-wide, often associated with El Niño events. Recovery was dependent on the vulnerability of individual reef areas and on the reef's previous history and resilience. At today's level of approximately 387 ppm, allowing a lag-time of 10 years for sea temperatures to respond, most reefs world-wide are committed to an irreversible decline. Mass bleaching will in future become annual, departing from the 4 to 7 years return-time of El Niño events. Bleaching will be exacerbated by the effects of degraded water-quality and increased severe weather events. In addition, the progressive onset of ocean acidification will cause reduction of coral growth and retardation of the growth of high magnesium calcite-secreting coralline algae. If CO(2) levels are allowed to reach 450 ppm (due to occur by 2030-2040 at the current rates), reefs will be in rapid and terminal decline world-wide from multiple synergies arising from mass bleaching, ocean acidification, and other environmental impacts. Damage to shallow reef communities will become extensive with consequent reduction of biodiversity followed by extinctions. Reefs will cease to be large-scale nursery grounds for fish and will cease to have most of their current value to humanity. There will be knock-on effects to ecosystems associated with reefs, and to other pelagic and benthic ecosystems. Should CO(2) levels reach 600 ppm reefs will be eroding geological structures with populations of surviving biota restricted to refuges. Domino effects will follow, affecting many other marine ecosystems. This is likely to have been the path of great mass extinctions of the past, adding to the case that anthropogenic CO(2) emissions could trigger the Earth's sixth

A Review on Successive Interference Cancellation-Based Optical PPM-CDMA Signaling

Science.gov (United States)

Alsowaidi, Naif; Eltaif, Tawfig; Mokhtar, Mohd Ridzuan

2017-06-01

This paper presents a comprehensive review of successive interference cancellation (SIC) scheme using pulse position modulation (PPM) for optical code division multiple access (OCDMA) systems. SIC scheme focuses on high-intensity signal, which will be selected after all users were detected, and then it will be subtracted from the overall received signal, hence, generating a new received signal. This process continues till all users eliminated one by one have been detected. It is shown that the random location of the sequences due to PPM encoding can reduce the probability of concentrated buildup of the pulse overlap in any one-slot time, and support SIC to easily remove the effect of the strongest signal at each stage of the cancellation process. The system bit error rate (BER) performance with modified quadratic congruence (MQC) codes used as signature sequence has been investigated. A detailed theoretical analysis of proposed system taking into account the impact of imperfect interference cancellation, the loss produced from the splitting during encoding and decoding, the channel loss and multiple access interference is presented. Results show that under average effective power constraint optical CDMA system using SIC scheme with M-ary PPM modulation outperforms conventional correlator detector and SIC scheme with on-off keying (OOK) modulation.

ATR kinase regulates its attenuation via PPM1D phosphatase ...

Indian Academy of Sciences (India)

Debadrita Bhattacharya

2018-02-07

Feb 7, 2018 ... generated in response to ultraviolet and ionizing radiation (Lu et al. 2005a, b; Cha ... nocopy' each other's effects by uncovering persistent ATR signalling that in ...... been shown to indirectly stabilize PPM1D by mediating the.

Development of the C-band (5712 MHz) 50 MW class PPM klystron (2)

International Nuclear Information System (INIS)

Matsumoto, H.; Shintake, T.; Ohkubo, Y.; Taoka, H.; Ohhashi, K.; Kakuno, K.

2001-01-01

Hot isostatic pressing (HIP) technique has been firstly applied to fabricate a magnetic circuit in a PPM klystron. Simply stacking disks of the magnetic stainless-steel (Mag-SUS) and oxygen-free-copper (OFC) alternatively, and processing in a HIP vessel filled with pressurised Ar-gas at 1200-kgf/cm 2 and temperature of 800degC for 2 hours, they were bonded in one block with diffusion bonding. No brazing-alloys were used in this process. After machining the rf-cavities and beam drift-tube on the bonded PPM stack, they were assembled together in one body by means of conventional brazing method. The C-band PPM klystron based on this technique was fabricated in the course of the Linear Collider R and D. Out-put power of 37 MW was generated with 2.5-μsec pulse width and 50 pps repetition rate. (author)

Organochlorine residues in bat guano from nine Mexican caves, 1991

Science.gov (United States)

Clark, D.R.; Moreno-Valdez, A.; Mora, M.A.

1995-01-01

Samples of bat guano, primarily from Mexican free-tailed bats (Tadarida brasiliensis), were collected at nine bat roosts in caves in northern and eastern Mexico and analysed for organochlorine residues. DDE, the most abundant residue found in each cave, was highest (0.99 p.p.m. dry weight) at Ojuela Cave, Durango. Other studies of DDE in bat guano indicate that this concentration is too low to reflect harmful concentrations in the bats themselves. The DDE at Ojuela may represent either lingering residues from use of DDT years ago in the Ojuela area of perhaps depuration loss from migrant bats with summer maternity roost(s) in a DDE-contaminated area such as Carlsbad Cavern, New Mexico. Presence of o,p-DDT at Tio Bartolo Cave, Nuevo Leon, indicates recent use of DDT, but the concentration of this contaminant was low. Possible impacts on bat colonies of the organophosphorus and carbamate insecticides now in extensive use are unknown.

PPM-based relay communication schemes for wireless body area networks

NARCIS (Netherlands)

Zhang, P.; Willems, F.M.J.; Huang, Li

2012-01-01

This paper investigates cooperative communication schemes based on a single relay with pulse-position modulation (PPM) signaling, for enhancing energy efficiency of wireless body area networks (WBANs) in noncoherent channel settings. We explore cooperation between the source and the relay such that

Evaluation of Total Nitrite Pattern Visualization as an Improved Method for Gunshot Residue Detection and its Application to Casework Samples.

Science.gov (United States)

Berger, Jason; Upton, Colin; Springer, Elyah

2018-04-23

Visualization of nitrite residues is essential in gunshot distance determination. Current protocols for the detection of nitrites include, among other tests, the Modified Griess Test (MGT). This method is limited as nitrite residues are unstable in the environment and limited to partially burned gunpowder. Previous research demonstrated the ability of alkaline hydrolysis to convert nitrates to nitrites, allowing visualization of unburned gunpowder particles using the MGT. This is referred to as Total Nitrite Pattern Visualization (TNV). TNV techniques were modified and a study conducted to streamline the procedure outlined in the literature to maximize the efficacy of the TNV in casework, while reducing the required time from 1 h to 5 min, and enhancing effectiveness on blood-soiled samples. The TNV method was found to provide significant improvement in the ability to detect significant nitrite residues, without sacrificing efficiency, that would allow for the determination of the muzzle-to-target distance. © 2018 American Academy of Forensic Sciences.

INFLUENCE OF RESIDUAL VARUS DEFORMITY ON CLINICAL, FUNCTIONAL, RADIOLOGICAL AND DYNAMOMETRIC OUTCOMES OF TOTAL KNEE ARTHROPLASTY

Directory of Open Access Journals (Sweden)

M. P. Zinoviev

2017-01-01

Full Text Available Purpose of the study – to evaluate the influence of residual varus deformity of the lower leg on clinical, functional and dynamometric outcomes of TKR.Material and methods. In the period from September 2014 till May 2015 951 total knee replacement surgeries were performed in Ural clinical and rehabilitation center in 933 patients with initial varus deformity of lower limb. However, in 52 cases (5.5% residual varus deformity of >3° persisted. The main group included 36 patients with mean residual varus deformity of lower leg of 3.9°±0.74° (from 3.1° to 5.6°, the control group included 34 patients with neutral mechanic axis of the lower leg. Evaluation of treatment outcomes was performed on average 14.2±1.8 months after the procedure using functional assessment of the patients according to KSS (Knee Society Score, subjective assessment of life quality (SF36, as well as evaluation of the static-dynamic function of the lower leg on diagnostic and treatment complex Biodex Systems 4 Quick Set and assessment of stability of components fixation by F.C. Ewald scale in modification of O.A. Kudinov et al.Results. Functional assessment of the patients according to KSS (Knee Society Score for the main group was 84.0±4.6, in control group – 82.2±4.1 points (p>0.05. Subjective assessment of life quality (SF36 in the main group was 162.6±6.4 points, in control group – 164.3±8.1 points (p>0.05. In terms of flexion and extension of lower leg there were no significant differences between two groups when assessing static and dynamic function by treatment and diagnostic complex «Biodex Systems 4 Quick Set» on average in 14.2±1.8 months after procedure: neither isometric nor isokinetic parameters in both groups demonstrated statistically significant differences (p>0.05. Based on X-rays evaluation there were no abnormalities in components fixation in both groups. There were no statistically significant differences identified in KSS and SF36 scales

Analysis of PPM-CDMA and OPPM-CDMA communication systems with new optical code

Science.gov (United States)

Liu, F.; Ghafouri-Shiraz, H.

2005-11-01

A novel type of optical spreading sequences, named the 'new-Modified Prime Code (nMPC)', is proposed for use in synchronous direct-detection optical code-division multiple-access (CDMA) systems which employ both pulse position modulation (PPM) and overlapping pulse position modulation (OPPM) schemes. The upper bounds on the bit error rate (BER) for nMPC used in PPM-CDMA systems are derived and compared with the respective systems, using a modified prime code (MPC) and a padded modified prime code (PMPC). The nMPC is further applied to the OPPM-CDMA system and the system with a proposed interference cancellation scheme. Our results show that under the same conditions the PPM-CDMA system performances are more improved with the use of nMPC than with the two other traditional codes. Moreover, they show that the system performances are significantly enhanced by the proposed interference reduction methods, if the nMPC is used in the OPPM-CDMA systems.

Evaluation of dried vegetables residues for poultry: II. Effects of feeding cabbage leaf residues on broiler performance, ileal digestibility and total tract nutrient digestibility.

Science.gov (United States)

Mustafa, A F; Baurhoo, B

2017-03-01

A study was conducted to investigate the effects of partial replacing corn and soybean meal with dried cabbage leaf residues (DCR) on broiler growth performance, apparent ileal nutrient digestibility, and apparent total tract nutrient utilization. Dietary treatments include 4 levels of DCR (0, 3, 6, and 9%). Two hundred and twenty-four day-old male broilers were randomly assigned to one of 4 groups (8 cage replicates; 7 birds/cage) and grown over a 35-d experimental period. Results showed that feeding DCR had no effects on daily body weigh gain (average 53.4 g/d), daily feed intake (average 94.9 g/d), and feed conversion ratio (average 1.78 g of feed/g of gain). Inclusion of DCR reduced apparent ileal DM (quadratic effect, P digestibility of younger birds (d 21) while incremental levels of DCR had no effect on apparent ileal nutrient digestibilities of older birds (d 35). Apparent total tract digestibility of DM, OM, and CP increased (linear effect, P digestibility of older birds and improved apparent total tract nutrient digestibility. © 2016 Poultry Science Association Inc.

Chlorine demand and residual chlorine decay kinetics of Kali river water at Kaiga project area

International Nuclear Information System (INIS)

Krishna Bhat, D.; Prakash, T.R.; Thimme Gowda, B.; Sherigara, B.S.; Khader, A.M.A.

1995-01-01

The nuclear power plant at Kaiga would use Kali river water for condenser cooling. This necessitated studies on the chemistry of chlorination such as chlorine demand, kinetics of chlorination and other water characteristics aimed at obtaining base line data. The study revealed significant seasonal variation of chlorine demand ranging from 0.5 ppm to 1.7 ppm (3.0 ppm dose, 30 min contact time) and total consumption of 5.0 ppm (10.0 ppm dose, 48 hours contact time). The reaction follows first order kinetics in chlorine. High correlation of chlorine demand with chlorophyll a, suspended matter, turbidity, silica, nitrite, phosphate and sulphate indicated that chlorine demand is greatly influenced by water quality. (author). 3 refs., 1 tab

Comparison of WDM/Pulse-Position-Modulation (WDM/PPM) with Code/Pulse-Position-Swapping (C/PPS) Based on Wavelength/Time Codes

Energy Technology Data Exchange (ETDEWEB)

Mendez, A J; Hernandez, V J; Gagliardi, R M; Bennett, C V

2009-06-19

Pulse position modulation (PPM) signaling is favored in intensity modulated/direct detection (IM/DD) systems that have average power limitations. Combining PPM with WDM over a fiber link (WDM/PPM) enables multiple accessing and increases the link's throughput. Electronic bandwidth and synchronization advantages are further gained by mapping the time slots of PPM onto a code space, or code/pulse-position-swapping (C/PPS). The property of multiple bits per symbol typical of PPM can be combined with multiple accessing by using wavelength/time [W/T] codes in C/PPS. This paper compares the performance of WDM/PPM and C/PPS for equal wavelengths and bandwidth.

Cats in Positive Energy Balance Have Lower Rates of Adipose Gain When Fed Diets Containing 188 versus 121 ppm L-Carnitine

Directory of Open Access Journals (Sweden)

M. A. Gooding

2016-01-01

Full Text Available L-carnitine (LC is included in select adult feline diets for weight management. This study investigated whether feeding adult cats with diets containing either 188 ppm of LC (LC188 or 121 ppm of LC (LC121 and feeding them 120% of maintenance energy requirement (MER resulted in differences in total energy expenditure (EE, metabolic fuel selection, BW, body composition, and behavior. Cats (n=20, 4±1.2 yrs were stratified for BCS and randomly assigned to one of two dietary treatments and fed for 16 weeks. BW was measured weekly, and indirect calorimetry, body composition, physical activity, play motivation, and cognition were measured at baseline and throughout the study. A mixed, repeated measures, ANCOVA model was used. Cats in both treatments gained BW (P0.05. There were no differences in body composition between groups at baseline; however, body fat (g and body fat : lean mass ratio were greater in cats fed LC121 in contrast to cats fed LC188 (P0.05. Supplying dietary LC at a dose of at least 188 ppm may be beneficial for the health and well-being of cats fed above MER.

Accumulation of pesticide residues by shrimp, fish and brine shrimp during pond culture at Ghorabari (District Thatta)

International Nuclear Information System (INIS)

Sultana, R.; Wajeeha, F.A.; Ameer, F.; Munshi, A.B.; Nasir, M.

2012-01-01

Residual level of persistent organo chlorines (OC) such as sigma-HCH (alpha-HCH, beta-HCH, gamma-HCH, delta-HCH, sigma-DDT (o,p'-DDD, op-DDE, p,p-DDE pp-DDD, pp'-DDT, o,p'-DDT), dieldrin and endrin were measured in a number of water samples from Ambro creek and their accumulation in shrimp (Penaeus merguiensis and P. penicillatus), fish (Otolithes ruber) and brine shrimp (Artemia sp.) reared in ponds for a period of four months. Samples were extracted with organic solvents, and quantified using gas chromatography-electron capture detection (GC/ECD). It has been found that results of animal tissue and water are not same however OCs, (mainly sigma DT and beta-HCH 4,4-DDT, Dieldrin + 2,4-DDT, and Methoxychlor were detected in all samples ). Heptachlor exo-epoxide were found in fish and Artemia sp. and absent in all shrimp samples. Heptachlor endo-epoxide was detected only in Artemia sp. and average residual concentration of OCs in Artemia sp. was 0.004-0.09 ppm. Methoxychlor was found in the highest quantity in all the samples whether it was fish, shrimp or Artemia. In fish average residual concentration of all (OCs) in individual sample was 0.03 - 0.180 ppm. (author)

10B-NMR determination of 10B-BPA, 10B-BPA–fructose complex and total 10B in blood for BNCT

International Nuclear Information System (INIS)

Yoshino, K.; Yabe, T.; Hattori, T.; Saito, K.; Ishikawa, A.; Ohki, H.

2014-01-01

First spontaneous, noninvasive determination method of 10 B-BPA, 10 B-BPA–fructose complex, and total 10 B in blood is described. 10 B-NMR measurement with 100,000 FT accumulation enables us to obtain the result within 100 min/sample. The detection limits for the simultaneous analysis were 3 ppm, 3 ppm and 6 ppm for 10 B-BPA, 10 B-BPA–fructose complex and total 10 B respectively in this study. By this method, we can actually discuss behavior of the 10 B-BPA–fructose complex in blood. - Highlights: • First 10 B-NMR determination of 10 B-BPA and 10 B-BPA–fructose complex in blood. • Total 10 B concentration in blood could be obtained by this method • The detection limit was 3 ppm for total 10 B

Depletion of [14C]clorsulon in cows' milk

International Nuclear Information System (INIS)

Chiu, S.H.L.; Baylis, F.P.; Taub, R.; Green, M.; Halley, B.A.; Bodden, R.M.

1989-01-01

Radioactive residue levels were determined in milk and plasma of Holstein cows dosed once with an oral suspension of 14 C-labeled clorsulon at 7 mg/kg of body weight. Average milk residue levels decreased from 0.54 ppm at 0.9 day postdose to 0.004 ppm at 6.9 days postdose with a half-life of 0.81 day. The drug residue was isolated by a batch adsorption method on an affinity agarose gel of carbonic anhydrase-Sepharose 4B and analyzed by HPCL-reverse isotope dilution assay (RIDA). This novel method greatly simplified the extraction of drug residue from milk and provided pure drug residue isolates. RIDA results of the isolates indicated that the unchanged drug was the major residue component in milk at 0-4 days postdose accounting for 56-99% of the total radioactive residue. Depletion half-life of the parent drug was 0.82 day, in close agreement with that of the total residue in milk. About 0.7% of the dose was recovered in the milk during the 6.9-day period

Determination of insecticides malathion and lambda-cyhalothrin residues in zucchini by gas chromatography

OpenAIRE

Lofty, Hayam M.; Abd El-Aleem, Abd El-Aziz A.; Monir, Hany H.

2013-01-01

A sensitive gas chromatographic method has been developed for the determination of malathion and lambda-cyhalothrin (λ-cyhalothrin) insecticide residues in zucchini. The developed method consists of extraction with acetone, purification and partitioning with methylene chloride, column chromatographic clean-up, and finally capillary gas chromatographic determination of the insecticides. The recoveries of method were greater than 90% and limit of determination was 0.001 ppm for both insecticide...

Monocrotophos and dicrotophos residues in birds as a result of misuse of organophosphates in Matagorda county Texas USA

Science.gov (United States)

Flickinger, Edward L.; White, D.H.; Mitchell, C.A.; Lamont, T.G.

1984-01-01

About 1100 birds of 12 spp. [Red-winged blackbird (Agelaius phoeniceus), great-tailed grackle (Quiscalus mexicanus), brown-headed cowbird (Molothrus ater), mourning dove (Zenaida macrours), Eastern meadowlark (Sturnella magna), vesper sparrow (Pooecetes gramineus), common snipe (Gallinago gallinago), blue-winged teal (Anas discors), mottled duck (Anas fulvigula), common moorhen (Gallinula chloropus), redhead (Aythya americana) and ruddy turnstone (Arenaria interpres)] died from organophosphate poisoning in Matagorda County on the Texas Gulf Coast in March and May 1982. Birds died from feeding on rice seed that was illegally treated with dicrotophos or monocrotophos and placed near rice fields as bait to attract and kill birds. Brain acetylcholinesterase inhibition of affected birds averaged 87% (range 82-89%), and contents of gastrointestinal tracts contained residues of dicrotophos (5.6-14 ppm) or monocrotophos (2.1-13 ppm). Rice seed collected at mortality sites contained 210 ppm dicrotophos or 950 ppm monocrotophos. Mortality from dicrotophos poisoning continued for almost 3 wk. The practice of illegally treating rice seed with either of the 2 organophosphates appears to be infrequent but widespread at present.

Cleaning verification: A five parameter study of a Total Organic Carbon method development and validation for the cleaning assessment of residual detergents in manufacturing equipment.

Science.gov (United States)

Li, Xue; Ahmad, Imad A Haidar; Tam, James; Wang, Yan; Dao, Gina; Blasko, Andrei

2018-02-05

A Total Organic Carbon (TOC) based analytical method to quantitate trace residues of clean-in-place (CIP) detergents CIP100 ® and CIP200 ® on the surfaces of pharmaceutical manufacturing equipment was developed and validated. Five factors affecting the development and validation of the method were identified: diluent composition, diluent volume, extraction method, location for TOC sample preparation, and oxidant flow rate. Key experimental parameters were optimized to minimize contamination and to improve the sensitivity, recovery, and reliability of the method. The optimized concentration of the phosphoric acid in the swabbing solution was 0.05M, and the optimal volume of the sample solution was 30mL. The swab extraction method was 1min sonication. The use of a clean room, as compared to an isolated lab environment, was not required for method validation. The method was demonstrated to be linear with a correlation coefficient (R) of 0.9999. The average recoveries from stainless steel surfaces at multiple spike levels were >90%. The repeatability and intermediate precision results were ≤5% across the 2.2-6.6ppm range (50-150% of the target maximum carry over, MACO, limit). The method was also shown to be sensitive with a detection limit (DL) of 38ppb and a quantitation limit (QL) of 114ppb. The method validation demonstrated that the developed method is suitable for its intended use. The methodology developed in this study is generally applicable to the cleaning verification of any organic detergents used for the cleaning of pharmaceutical manufacturing equipment made of electropolished stainless steel material. Copyright © 2017 Elsevier B.V. All rights reserved.

Chemical exchange rotation transfer imaging of intermediate-exchanging amines at 2 ppm.

Science.gov (United States)

Zu, Zhongliang; Louie, Elizabeth A; Lin, Eugene C; Jiang, Xiaoyu; Does, Mark D; Gore, John C; Gochberg, Daniel F

2017-10-01

Chemical exchange saturation transfer (CEST) imaging of amine protons exchanging at intermediate rates and whose chemical shift is around 2 ppm may provide a means of mapping creatine. However, the quantification of this effect may be compromised by the influence of overlapping CEST signals from fast-exchanging amines and hydroxyls. We aimed to investigate the exchange rate filtering effect of a variation of CEST, named chemical exchange rotation transfer (CERT), as a means of isolating creatine contributions at around 2 ppm from other overlapping signals. Simulations were performed to study the filtering effects of CERT for the selection of transfer effects from protons of specific exchange rates. Control samples containing the main metabolites in brain, bovine serum albumin (BSA) and egg white albumen (EWA) at their physiological concentrations and pH were used to study the ability of CERT to isolate molecules with amines at 2 ppm that exchange at intermediate rates, and corresponding methods were used for in vivo rat brain imaging. Simulations showed that exchange rate filtering can be combined with conventional filtering based on chemical shift. Studies on samples showed that signal contributions from creatine can be separated from those of other metabolites using this combined filter, but contributions from protein amines may still be significant. This exchange filtering can also be used for in vivo imaging. CERT provides more specific quantification of amines at 2 ppm that exchange at intermediate rates compared with conventional CEST imaging. Copyright © 2017 John Wiley & Sons, Ltd.

Total hip arthroplasty performed in patients with residual poliomyelitis: does it work?

Science.gov (United States)

Yoon, Byung-Ho; Lee, Young-Kyun; Yoo, Jeong Joon; Kim, Hee Joong; Koo, Kyung-Hoi

2014-03-01

Patients with residual poliomyelitis can have advanced degenerative arthritis of the hip in the paralytic limb or the nonparalytic contralateral limb. Although THA is a treatment option for some of these patients, there are few studies regarding THA in this patient population. We therefore reviewed a group of patients with residual poliomyelitis who underwent cementless THA on either their paralytic limb or nonparalytic limb to assess (1) Harris hip scores, (2) radiographic results, including implant loosening, (3) complications, including dislocation, and (4) limb length discrepancy after recovery from surgery. From January 2000 to December 2009, 10 patients with residual poliomyelitis (10 hips, four paralytic limbs and six nonparalytic contralateral limbs) underwent THA using cementless prostheses. Harris hip scores, complications, and leg length discrepancy were determined by chart review, and confirmed by questionnaire and examination; radiographs were reviewed by two observers for this study. Followup was available for all 10 patients at a minimum of 3 years (median, 7 years; range, 3.4-13 years). Surgery was done at the same side of the paralytic limb in four hips and contralateral to the paralytic limb in six. All patients had pain relief and improvement in function; the Harris hip score improved from mean of 68 preoperatively to 92 at last followup (p = 0.043). However, only three patients had complete pain relief. One hip dislocated, which was treated successfully with closed reduction and a hip spica cast for 2 months. There was no loosening or osteolysis in this series. Leg length discrepancy improved after the index operation, but only in the THAs performed in the paralytic limbs. Cementless THA may be suitable for painful hips in adult patients with residual poliomyelitis. Nonetheless, these patients should be informed of the possibility of mild residual pain and persistent leg length discrepancy, particularly patients whose THA is performed on the

Residual strain in the Nb-H system measured by selected area diffraction (SAD)

International Nuclear Information System (INIS)

Bulhoes, I.A.M.; Akune, K.; Pinatti, Dyonisio G.

1981-07-01

Various specimens of Nb were annealed in vacuum of 10 -3 torr for four hours at 1770 0 K. These speciments were doped with hydrogen up to 1000 ppm by weight and then were analyzed selected area diffraction. The line resolution of the electron channelling pattern was meassured for the specimens with different hydrogen content. These measurements, combined with the measurement of density, permitted one to estimate the residual strain caused by hydrogen. (Author) [pt

X-ray clusters from a high-resolution hydrodynamic PPM simulation of the cold dark matter universe

Science.gov (United States)

Bryan, Greg L.; Cen, Renyue; Norman, Michael L.; Ostriker, Jermemiah P.; Stone, James M.

1994-01-01

A new three-dimensional hydrodynamic code based on the piecewise parabolic method (PPM) is utilized to compute the distribution of hot gas in the standard Cosmic Background Explorer (COBE)-normalized cold dark matter (CDM) universe. Utilizing periodic boundary conditions, a box with size 85 h(exp-1) Mpc, having cell size 0.31 h(exp-1) Mpc, is followed in a simulation with 270(exp 3)=10(exp 7.3) cells. Adopting standard parameters determined from COBE and light-element nucleosynthesis, Sigma(sub 8)=1.05, Omega(sub b)=0.06, we find the X-ray-emitting clusters, compute the luminosity function at several wavelengths, the temperature distribution, and estimated sizes, as well as the evolution of these quantities with redshift. The results, which are compared with those obtained in the preceding paper (Kang et al. 1994a), may be used in conjuction with ROSAT and other observational data sets. Overall, the results of the two computations are qualitatively very similar with regard to the trends of cluster properties, i.e., how the number density, radius, and temeprature depend on luminosity and redshift. The total luminosity from clusters is approximately a factor of 2 higher using the PPM code (as compared to the 'total variation diminishing' (TVD) code used in the previous paper) with the number of bright clusters higher by a similar factor. The primary conclusions of the prior paper, with regard to the power spectrum of the primeval density perturbations, are strengthened: the standard CDM model, normalized to the COBE microwave detection, predicts too many bright X-ray emitting clusters, by a factor probably in excess of 5. The comparison between observations and theoretical predictions for the evolution of cluster properties, luminosity functions, and size and temperature distributions should provide an important discriminator among competing scenarios for the development of structure in the universe.

Residual effect of applying composted sewage sludge to the majority nutrients in an alive grove soil; Efecto residual de la aplicacion de un lodo de depuradora compostado sobre los nutrientes mayoritarios de un suelo de olivar

Energy Technology Data Exchange (ETDEWEB)

Ordonez Fernandez, R.; Aguilar Torres, M. A.; Gonzalez Fernandez, P.

2002-07-01

The agricultural reuse of sewage sludge is an excellent management option because in addition to the elimination of the residue, from the environment an appreciable amount of nitrogen, phosphorus and some micronutrients are added to the soil. During two successive years 20 Mgha-1of composted sewage sludge was applied to a clay soil of the Campina de Cordoba cropped with olive trees. The concentrations of some of the main nutrients like phosphorus and potassium increased after the amendment. The phosphorus content in the surface soil horizon increased from 2.3 to 9.3 ppm whereas the potassium content increased from 239 to 320 ppm in the same horizon for the same two years period. These results are encouraging for the organic amendment use. (Author)

Measurement of low-ppm mixing ratios of water vapor in the upper troposphere and lower stratosphere using chemical ionization mass spectrometry

Directory of Open Access Journals (Sweden)

T. D. Thornberry

2013-06-01

Full Text Available A chemical ionization mass spectrometer (CIMS instrument has been developed for the fast, precise, and accurate measurement of water vapor (H2O at low mixing ratios in the upper troposphere and lower stratosphere (UT/LS. A low-pressure flow of sample air passes through an ionization volume containing an α-particle radiation source, resulting in a cascade of ion-molecule reactions that produce hydronium ions (H3O+ from ambient H2O. The production of H3O+ ions from ambient H2O depends on pressure and flow through the ion source, which were tightly controlled in order to maintain the measurement sensitivity independent of changes in the airborne sampling environment. The instrument was calibrated every 45 min in flight by introducing a series of H2O mixing ratios between 0.5 and 153 parts per million (ppm, 10−6 mol mol−1 generated by Pt-catalyzed oxidation of H2 standards while overflowing the inlet with dry synthetic air. The CIMS H2O instrument was deployed in an unpressurized payload area aboard the NASA WB-57F high-altitude research aircraft during the Mid-latitude Airborne Cirrus Properties Experiment (MACPEX mission in March and April 2011. The instrument performed successfully during seven flights, measuring H2O mixing ratios below 5 ppm in the lower stratosphere at altitudes up to 17.7 km, and as low as 3.5 ppm near the tropopause. Data were acquired at 10 Hz and reported as 1 s averages. In-flight calibrations demonstrated a typical sensitivity of 2000 Hz ppm−1 at 3 ppm with a signal to noise ratio (2 σ, 1 s greater than 32. The total measurement uncertainty was 9 to 11%, derived from the uncertainty in the in situ calibrations.

Prediction of ppm level electrical failure by using physical variation analysis

Science.gov (United States)

Hou, Hsin-Ming; Kung, Ji-Fu; Hsu, Y.-B.; Yamazaki, Y.; Maruyama, Kotaro; Toyoshima, Yuya; Chen, Chu-en

2016-03-01

their spatial correlation distance. For local variations (LV) there is no correlation, whereas for global variations (GV) the correlation distance is very large [7]-[9]. This is the first time to certificate the validation of spatial distribution from the affordable bias contour big data fundamental infrastructures. And then apply statistical techniques to dig out the variation sources. The GV come from systematic issue, which could be compensated by adaptive LT condition or OPC correction. But LV comes from random issue, which being considered as intrinsic problem such as structure, material, tool capability… etc. In this paper studying, we can find out the advanced technology node SRAM contact CD local variation (LV) dominates in total variation, about 70%. It often plays significant in-line real time catching WP-DPMO role of the product yield loss, especially for wafer edge is the worst loss within wafer distribution and causes serious reliability concern. The major root cause of variations comes from the PR material induced burr defect (LV), the second one comes from GV enhanced wafer edge short opportunity, which being attributed to three factors, first one factor is wafer edge CD deliberated enlargement for yield improvement as shown in Fig. 10. Second factor is overlaps/AA shifts due to tool capability dealing with incoming wafer's war page issue and optical periphery layout dependent working pitch issue as shown in Fig. 9 (1)., the last factor comes from wafer edge burr enhanced by wafer edge larger Photo Resistance (PR) spin centrifugal force. After implementing KPIs such as GV related AA/CD indexes as shown in Fig. 9 (1) and 10, respectively, and LV related burr index as shown in Fig. 11., we can construct the parts per million (PPM) level short probability model via multi-variables regression, canonical correlation analysis and logistic transformation. The model provides prediction of PPM level electrical failure by using in-line real time physical

Residues of tritium-labeled morantel in lactating dairy cattle

International Nuclear Information System (INIS)

Lynch, M.J.; Mosher, F.R.; Burnett, D.M.; Newby, T.J.

1987-01-01

Residues of morantel and its metabolites were monitored in plasma, urine, and milk of five lactating dairy cattle that received an oral dose of [4,4-pyrimidyl- 3 H 2 ]morantel tartrate at 10 mg/kg. Drug-related radioactivity peaked in plasma at 8 h and in milk by the second milking, postdose, and was 170 and 84 ng/mL, respectively. The fraction of total residues in milk convertible to the marker compound, N-methyl-1,3-propanediamine, was 0.38 on the basis of a comparison of the areas under the curves for total and marker residues. Five days after dosing, 3.9% of the total radioactivity in liver was recovered as tritium water. Total drug-related residues in this target tissue averaged 1.15 μg/g. About half of the drug-related residues in liver was unextractable and was classified by bound

Use of 60 ppm deuterium depleted water in companionship animals

International Nuclear Information System (INIS)

Balint, Emilia; Manolescu, N.; Cranganu, D.; Militaru, Manuela; Pop, Aneta; Codreanu, M.; Panait, Marieta; Lastofka, D.

2004-01-01

There are presented the results of studies on the effects of deuterium depleted water in companionship animals. Based on these results, a new product was realized, 'Aqua Forte' that is a deuterium depleted potable water (60 ppm deuterium) with beneficial effects in animal's health maintaining. Aqua forte has prophylactic properties (in preventing diseases related to immune system) and therapeutic properties, as adjuvant in various therapeutic programs. The mechanism of action takes place at the cellular metabolism level by replacing the constitutional and free water of 150 ppm deuterium, this resulting in the stimulation of the immune cellular system and also of resistance at the onset of some pathological states. The non-specific stimulation implies performing both the humoral mediated immune reactions and of those cellularly mediated. Aqua forte is recommended in: - the feeding of the young weaned animals, the action being of growth stimulation, and increasing of the resistance against some diseases specific to the age; - as an adjuvant in some chronic diseases (hepatitis, pancreatitis, dermatological diseases, osteoarthropaties, hepato-renal syndrome, renal insufficiency, after surgical interventions, in antitumoral therapy); - in the feeding of the old animals for the quality of life improvement. (authors)

Lead residues in plants and soils along Austrian motor roads

International Nuclear Information System (INIS)

Horak, O.; Rebler, R.; Schmidt, J.

1977-01-01

Plant samples from 63 roadside locations were collected monthly, with the exception of January and February, beginning in July 1972 and ending in June 1973. Lead contents were determined after wet digestion by techniques of atomic absorption spectroscopy. The results, calculated by analysis of variance, show, that the contamination of plants with airborne lead residues from motor car exhausts depends not only on the density of traffic and the distance from the road, but also on the season. In spring, when the vegetative plant growth starts, lead levels of the vegetation are decreasing and remain nearly constant from May to July. From August onwards a gradual increase in the lead content of plants occurs, which becomes more distinctly at the end of the season when the plant growth stops. The highest lead contents (up to 500 ppm) were found in plant matter collected during the winter months. Lead was determined in a number of roadside soils. Extremely high amounts (up to nearly 800 ppm) were found in uncultivated soils near busy highways. (author)

Accurate Analytical Multiple-Access Performance of Time-Hopping Biorthogonal PPM IR-UWB Systems

Directory of Open Access Journals (Sweden)

SVEDEK, T.

2011-05-01

Full Text Available In this paper, the characteristic function (CF method is used to derive the symbol error rate (SER expression for time-hopping impulse radio ultra-wideband (TH-IR-UWB systems with a biorthogonal pulse position modulation (BPPM scheme in the presence of a multi-user interference (MUI. The derived expression is validated with the Monte-Carlo simulation and compared with orthogonal PPM. Moreover, the analytical results are compared with the Gaussian approximation (GA of MUI which is shown to be inaccurate for a medium and large signal-to-noise ratio (SNR. It is also shown that the BPPM scheme outperforms the PPM scheme for all SNR. At the end, the influence of different system parameters on the BPPM performance is analyzed.

Chromium Fractions Changes Compared With Total-Cr As Determined by Neutron Activation Analysis Technique

International Nuclear Information System (INIS)

Abdel-Sabour, M.F.; Abdou, F.M.; Elwan, I.M.; Al-Salama, Y.J.

2003-01-01

Fifteen soil samples were chosen from different locations (five different locations at north greater Cairo, Egypt to represent different soils (alluvial and sandy) as well as different source of contaminated wastewater (sewage and industrial effluent). Using sequential extraction technique (extracting the soil with different solutions, which is designed to separate metal fractions), Cr was separated into six operationally defined fractions water soluble, exchangeable, carbonate bound, Fe-Mn oxides bound, organic bound and residual fractions. Result of soil total-Cr indicated the serious accumulation of Cr in soils subjected to prolonged irrigation with contaminated wastewater. As it could seen, total-Cr in the tested contaminated soils exceeds the permissible levels (75-100)ppm Cr by several order of magnitude particularly at the surface and subsurface layers. The highest accumulation of total Cr down to depth 60 cm was observed in case of soil E. Data showed that values of total Cr determined by NAA method were always higher than the relevant values determined either by AAS or those calculated after the sequential extraction method. T-test analysis showed the significant difference between NAA and either AAS or sequential extraction methods. Although T-test analysis showed that were significant differences between total content in soils as determined by destructive (AAS or SUM) and non-destructive (NAA) analytical techniques however, strong liner relation between NAA and other tested methods was obtained. Chromium distribution between different extractants shows that the greatest amounts are found in the residual and Occluded in Fe and Mn-Oxides fractions followed by carbonate or organic fractions. In most cases the proportion of all tested Cr-forms has increased in contaminated soil layers with higher enrichment in organically bound Cr, occluded in Fe and Mn oxides, carbonate exchangeable and soluble fractions. Results indicate that soil properties have a

The fluorimetric titration of zirconium in the ppm-range

International Nuclear Information System (INIS)

Linden, W.E. von der; Boef, G. den; Ozinga, W.

1976-01-01

A fluorimetric titration of zirconium(IV) with EDTA is proposed. The fluorescence intensity of the zirconium-morin complex is used to indicate the end-point. More than twenty other cations were investigated and it was found that they did not interfere, neither did common anions. Mercury(II) can only be tolerated in amount not exceeding that of zirconium. Bismuth(III) interferes and hafnium(IV0 is titrated together with zirconium. The relative standard deviation of the titration of 10ml of a solution containing 1 ppm of zirconium does not exceed 1.5%

Integral biostimulation of soil polluted by 60000 ppm of motor waste oil

Directory of Open Access Journals (Sweden)

Saucedo-Martínez Blanca Celeste

2017-08-01

Full Text Available Waste motor oil (WMO is a mixture of hydrocarbons (HICO soil pollutants. An alternative solution for its elimination is the biostimulation (BIS, secuancial, complementary and accumulative or integral which requires at first BIS by detergents to emulsify WMO, the second one following by enrichment by mineral solution, H2O2 as a O2 source for oxidation of WMO and controlling moisture soil content at 80% field capacity for exchange gases in soil to stimulate WMO mineralization The aim of the work was: i analyze in the integral BIS of contaminated soil by 60000 ppm of WMO. The first BIS was applying detergents to emulsify the WMO, the second BIS by mineral solution, then by H2O2, under humidity control at 80% of field capacity, for the best oxidation of WMO. Additionally bacterial population oxidant WMO was meas-ured, to select those which synthetized detergent related to WMO degradation, finally the type of bacteria were molecular identify. Results showed than integral BIS by an anionic / nonionic detergent, then en-richment with mineral solution, and 0.5% H2O2, reduced WMO from 60000 ppm to 27200 ppm in 23 days. Density of bacterial WMO oxidant population was 268 X 106 CFU/g dry soil, from which the domi-nant ones were selected and identified 47 bacterial genera divided into: Actinomycetes, Firmicutes and Proteobacteria. These results showed that soil pollution by high concentration level of WMO demanded at integrated BIS, also was found some bacterial genus which synthetized detergent with potential used in soil polluted by WMO.

Sub-ppm analysis using a compact EDX

International Nuclear Information System (INIS)

Muraoka, Koichi; Utaka, Tadashi; Taniguchi, Kazuo

2009-01-01

As an important solution for the Soil Contamination Countermeasures Laws and China RoHS as well as EU WEEE/RoHS/ELV Directives, an EDX analyzer has been utilized as a simple and convenient instrument for promptly screening the hazardous heavy elements with high reproducibility in non-destructive manner. However, with the increasing varieties of measuring samples, the development of a high performance, more convenient and portable instrument has been expected. To meet these demands, based on the compact X-ray optical technology, using a miniature X-ray tube, a primary beam filter method and portable semiconductor detector with Peltier cooling system, we have developed a high-performance EDX Analyzer. In this study, thus, the hardware configurations and the obtained research results for sub-ppm analysis of Cd in brown rice and soil are reported. (author)

Attenuated total reflectance-FT-IR spectroscopy for gunshot residue analysis: potential for ammunition determination.

Science.gov (United States)

Bueno, Justin; Sikirzhytski, Vitali; Lednev, Igor K

2013-08-06

The ability to link a suspect to a particular shooting incident is a principal task for many forensic investigators. Here, we attempt to achieve this goal by analysis of gunshot residue (GSR) through the use of attenuated total reflectance (ATR) Fourier transform infrared spectroscopy (FT-IR) combined with statistical analysis. The firearm discharge process is analogous to a complex chemical process. Therefore, the products of this process (GSR) will vary based upon numerous factors, including the specific combination of the firearm and ammunition which was discharged. Differentiation of FT-IR data, collected from GSR particles originating from three different firearm-ammunition combinations (0.38 in., 0.40 in., and 9 mm calibers), was achieved using projection to latent structures discriminant analysis (PLS-DA). The technique was cross (leave-one-out), both internally and externally, validated. External validation was achieved via assignment (caliber identification) of unknown FT-IR spectra from unknown GSR particles. The results demonstrate great potential for ATR-FT-IR spectroscopic analysis of GSR for forensic purposes.

A SUBCHRONIC INHALATION STUDY OF FISCHER 344 RATS EXPOSED TO 0, 0.4, 1.4 OR 4.0 PPM ACROLEIN

International Nuclear Information System (INIS)

KUTZMAN, R.S.

1981-01-01

Fischer 344 rats were exposed to 0.0, 0.4, 1.4, or 4.0 ppm acrolein for 62 days. The major objective of the study was to relate the results of a series of pulmonary function tests to biochemical and pathological alterations observed in the lung. Cytological and reproductive potential endpoints were also assessed after acrolein exposure. Rats were exposed to acrolein for 6 hours/day, 5 days/week for 62 days. Mortality was observed only in the 4.0 ppm chamber where 32 of 57 exposed males died; however, none of the 8 exposed females died. Most of the mortality occurred within the first 10 exposure days. Histologic examination indicated that the animals died of acute bronchopneumonia. The surviving males and females exposed to 4.0 ppm acrolein gained weight at a significantly slower rate than control animals. The growth of both sexes in the 0.4 and 1.4 ppm groups was similar to that of their respective controls. Histopathologic examination of animals after 62 days of exposure revealed bronchiolar epithelial necrosis and sloughing, bronchiolar edema with macrophages, and focal pulmonary edema in the 4.0 ppm group. These lesions were, in some cases, associated with edema of the trachea and peribronchial lymph nodes, and acute rhinitis which indicated an upper respiratory tract effect of acrolein. Of particular interest was the variability of response between rats in the 4.0 ppm group, some not affected at all while others were moderately affected. Intragroup variability in toxicity was also apparent in the 1.4 ppm exposure group where only 3 of 31 animals examined had lesions directly related to acrolein exposure. Extra respiratory organs appeared unaffected

PENGARUH VARIASI KONSENTRASI ADSORBEN BIJI TREMBESI TERHADAP PENURUNAN KADAR LOGAM KROMIUM (CR TOTAL PADA LIMBAH INDUSTRI SASIRANGAN

Directory of Open Access Journals (Sweden)

Gusti Indah Hayati

2016-10-01

Full Text Available The production process of sasirangan fabric produced liquid waste from dyeing and coloring process. One of the pollutant that contained in liquid waste was chrom metal. Reduction of Cr metal from sasirangan industrial liquid waste used tamarind (trembesi seeds as the adsorbent. The purpose of this research was to know the effect of adsorbent concentration 1; 2; 3 and 4 % w/v to reduction of Cr metal in sasirangan industry. Variation of adsorbent concentration that used 1 g/100 ml, 2 g/100 ml, 3 g/100 ml and 4 g/100 ml Sasirangan liquid waste by stirring for 30 minutes in 100 rpm at 55oC and the size of adsorbent was 250 micron. The pyrolisis process had setting at 450oC temperatures for 5 hours operation. Adsorbent was activated by HCl 0.1N for 24 hours. Chrom metal residu which contained in sasirangan waste was analyzed using ICP (inductively coupled plasma. This analysis aims to determine residual chrom metal concentration in sasirangan industries after adsorption process. The greater adsorbent was added at adsorption process, the less residual chrom metal concentration which contained in sasirngan waste. The results of this research showed that adsorbent can decrease Cr metal up to 80.65%. The initial concentration of Cr metal in sasirangan waste was 2 ppm and the decreasing of Cr metal maximum remaining was 0.347 ppm at 2 g adsorbent.

Quantification of residual solvents in antibody drug conjugates using gas chromatography

Energy Technology Data Exchange (ETDEWEB)

Medley, Colin D., E-mail: medley.colin@gene.com [Genentech Inc., Small Molecule Pharmaceutical Sciences, 1 DNA Way, South San Francisco, CA 94080 (United States); Kay, Jacob [Research Pharmaceutical Services, 520 Virginia Dr. Fort, Washington, PA (United States); Li, Yi; Gruenhagen, Jason; Yehl, Peter; Chetwyn, Nik P. [Genentech Inc., Small Molecule Pharmaceutical Sciences, 1 DNA Way, South San Francisco, CA 94080 (United States)

2014-11-19

Highlights: • Sensitive residual solvents detection in ADCs. • 125 ppm QL for common conjugation solvents. • Generic and validatable method. - Abstract: The detection and quantification of residual solvents present in clinical and commercial pharmaceutical products is necessary from both patient safety and regulatory perspectives. Head-space gas chromatography is routinely used for quantitation of residual solvents for small molecule APIs produced through synthetic processes; however residual solvent analysis is generally not needed for protein based pharmaceuticals produced through cultured cell lines where solvents are not introduced. In contrast, antibody drug conjugates and other protein conjugates where a drug or other molecule is covalently bound to a protein typically use solvents such as N,N-dimethylacetamide (DMA), N,N‑dimethylformamide (DMF), dimethyl sulfoxide (DMSO), or propylene glycol (PG) to dissolve the hydrophobic small molecule drug for conjugation to the protein. The levels of the solvent remaining following the conjugation step are therefore important to patient safety as these parental drug products are introduced directly into the patients bloodstream. We have developed a rapid sample preparation followed by a gas chromatography separation for the detection and quantification of several solvents typically used in these conjugation reactions. This generic method has been validated and can be easily implemented for use in quality control testing for clinical or commercial bioconjugated products.

Rapid, quantitative analysis of ppm/ppb nicotine using surface-enhanced Raman scattering from polymer-encapsulated Ag nanoparticles (gel-colls).

Science.gov (United States)

Bell, Steven E J; Sirimuthu, Narayana M S

2004-11-01

Rapid, quantitative SERS analysis of nicotine at ppm/ppb levels has been carried out using stable and inexpensive polymer-encapsulated Ag nanoparticles (gel-colls). The strongest nicotine band (1030 cm(-1)) was measured against d(5)-pyridine internal standard (974 cm(-1)) which was introduced during preparation of the stock gel-colls. Calibration plots of I(nic)/I(pyr) against the concentration of nicotine were non-linear but plotting I(nic)/I(pyr) against [nicotine](x)(x = 0.6-0.75, depending on the exact experimental conditions) gave linear calibrations over the range (0.1-10 ppm) with R(2) typically ca. 0.998. The RMS prediction error was found to be 0.10 ppm when the gel-colls were used for quantitative determination of unknown nicotine samples in 1-5 ppm level. The main advantages of the method are that the gel-colls constitute a highly stable and reproducible SERS medium that allows high throughput (50 sample h(-1)) measurements.

Novel determination of the total phenolic content in crude plant extracts by the use of 1H NMR of the -OH spectral region

International Nuclear Information System (INIS)

Nerantzaki, A.A.; Tsiafoulis, C.G.; Charisiadis, P.; Kontogianni, V.G.; Gerothanassis, I.P.

2011-01-01

A novel method for the determination of the total phenolic content using 1 H NMR spectroscopy in the -OH spectral region is presented. The use of DMSO-d 6 , which is an aprotic and strongly hydrogen bonding solvent, allows the 'appearance' of the relative sharp resonances of phenolic hydroxyl protons in the region of 8-14 ppm. The determination of the total phenolic -OH content requires three steps: (i) a 1D 1 H NMR spectrum is obtained in DMSO-d 6 ; (ii) a subsequent 1D 1 H NMR spectrum is recorded with irradiation of the residual water signal which results in the elimination or reduction of the phenolic -OH groups, due to proton exchange; and (iii) 1D 1 H NMR spectra are recorded with the addition of a progressively increased amount of salt, NaHCO 3 , which results in extensive linebroadening of the COOH resonances thus allowing the discrimination of the phenolic from the carboxylic acid signals. Integration, with respect to the internal standard TSP-d 4 , of the signal resonances between 14 and 8 ppm in spectrum (i) which are either eliminated or reduced in intensity in steps (ii) and (iii) allows the quantitation of the total phenolic content. The method was applied to model compounds, a mixture of them and several extracts of natural products. The results of the proposed 1 H NMR method were compared to the Folin-Ciocalteu (FC) reagent method. Additionally, since 1 H NMR refers to the total phenolic hydroxyl protons, a reaction factor, A e , is proposed that corresponds to the hydroxyl reactivity. The 1 H NMR method is rapid and accurate bearing the inherent advantages of the NMR spectroscopy and can be applied directly in complex extracts. Furthermore, it can be applied in a wide range of matrixes from crude plant extracts and food products to biological samples.

Amended final report on the safety assessment of polyacrylamide and acrylamide residues in cosmetics.

Science.gov (United States)

2005-01-01

Polyacrylamide is a polymer of controllable molecular weight formed by the polymerization of acrylamide monomers available in one of three forms: solid (powder or micro beads), aqueous solution, or inverse emulsions (in water droplets coated with surfactant and suspended in mineral oil). Residual acrylamide monomer is likely an impurity in most Polyacrylamide preparations, ranging from cosmetic formulations, at concentrations ranging from 0.05% to 2.8%. Residual levels of acrylamide in Polyacrylamide can range from dogs treated with Polyacrylamide at doses up to 464 mg/kg body weight showed no signs of toxicity. Several 2-year chronic oral toxicity studies in rats and dogs fed diets containing up to 5% Polyacrylamide had no significant adverse effects. Polyacrylamide was not an ocular irritant in animal tests. No compound-related lesions were noted in a three-generation reproductive study in which rats were fed 500 or 2000 ppm Polyacrylamide in their diet. Polyacrylamide was not carcinogenic in several chronic animal studies. Human cutaneous tolerance tests performed to evaluate the irritation of 5% (w/w) Polyacrylamide indicated that the compound was well tolerated. Acrylamide monomer residues do penetrate the skin. Acrylamide tested in a two-generation reproductive study at concentrations up to 5 mg/kg day(- 1) in drinking water, was associated with prenatal lethality at the highest dose, with evidence of parental toxicity. The no adverse effects level was close to the 0.5 mg/kg day(- 1) dose. Acrylamide tested in a National Toxicology Program (NTP) reproductive and neurotoxicity study at 3, 10, and 30 ppm produced no developmental or female reproductive toxicity. However, impaired fertility in males was observed, as well as minimal neurotoxic effects. Acrylamide neurotoxicity occurs in both the central and peripheral nervous systems, likely through microtubule disruption, which has been suggested as a possible mechanism for genotoxic effects of acrylamide in

PPM1K Regulates Hematopoiesis and Leukemogenesis through CDC20-Mediated Ubiquitination of MEIS1 and p21

Directory of Open Access Journals (Sweden)

Xiaoye Liu

2018-05-01

Full Text Available Summary: In addition to acting as building blocks for biosynthesis, amino acids might serve as signaling regulators in various physiological and pathological processes. However, it remains unknown whether amino acid levels affect the activities of hematopoietic stem cells (HSCs. By using a genetically encoded fluorescent sensor of the intracellular levels of branched-chain amino acids (BCAAs, we could monitor the dynamics of BCAA metabolism in HSCs. A mitochondrial-targeted 2C-type Ser/Thr protein phosphatase (PPM1K promotes the catabolism of BCAAs to maintain MEIS1 and p21 levels by decreasing the ubiquitination-mediated degradation controlled by the E3 ubiquitin ligase CDC20. PPM1K deficiency led to a notable decrease in MEIS1/p21 signaling to reduce the glycolysis and quiescence of HSCs, followed by a severe impairment in repopulation activities. Moreover, the deletion of Ppm1k dramatically extended survival in a murine leukemia model. These findings will enhance the current understanding of nutrient signaling in metabolism and function of stem cells. : Liu et al. show that the dynamics of BCAA metabolism in hematopoietic stem cells (HSCs and leukemia-initiating cells (LICs can be monitored by a genetically encoded fluorescent sensor. PPM1K promotes BCAA catabolism and maintains the glycolysis and quiescence of HSCs/LICs through the downregulation of CDC20-mediated ubiquitination of MEIS1 and p21. Keywords: branched-chain amino acids, PPM1K, ubiquitination, CDC20, MEIS1/p21, hematopoietic stem cells, leukemia-initiating cells

Biostimulation of soil impacted by 45000 ppm waste motor oil and Phytoremediation with Zea mays by Burkholderia cepacia and Rhizobium elti

Directory of Open Access Journals (Sweden)

Saucedo-Martínez Blanca Celeste

2016-08-01

Full Text Available Soil contaminated with 45000 ppm of waste motor oil (WMO is a relatively high concentration of a mixture of aliphatic and aromatic hydrocarbons (HC, inhibits mineralization of organic matter and its fertility. This WMO´ concentration is high according to mexican regulation: NOM-138-SEMARNAT/ SSA1-2012 (NOM-138 related to when it exceeds 4400 ppm/Kg of soil. The aims of the study were: i BS of contaminated soil by 45000 ppm of WMO with vermicompost and bovine compost 3%, and ii PR using Zea mays inoculated with B. cepacia and R. etli at value below the maximum allowable by NOM-138. The main response variable of the trial was initial and final concentration of WMO after BS. In PR by Z. mays and PGPB to reduce remain-ing WMO, were phenological response variables as: plant height and root length and biomass: aerial and root fresh and dry weight. Experimental data were analyzed by ANOVA and Tukey. Results showed that the BS of soil by 45000 ppm of WMO was reduced to 21000 ppm; subsequent FR sowing Z. mays inoculated by B. cepacia decreased to 1822.5 ppm, value below the maximum allowable by NOM-138. BS of contaminated soil by relatively high concentration of WMO and later FR sowing Z. mays and PGPR. Both are an alternative in its remediation that to apply each one alone.

Control of Established Gingivitis and Dental Plaque Using a 1450 ppm Fluoride/Zinc-based Dentifrice: A Randomized Clinical Study.

Science.gov (United States)

Zhong, Y; Li, X; Hu, D Y; Mateo, L R; Morrison, B M; Delgado, E; Zhang, Y P

2015-01-01

To investigate the clinical efficacy in controlling established gingivitis and dental plaque of a 1450 ppm fluoride as sodium monofluorophosphate (SMFP)/zinc-based dentifrice, as compared to a zinc-free dentifrice with 1450 ppm fluoride as SMFP after six months product use. A six-month clinical study, with eighty-six (86) subjects, was conducted in Chengdu, China, using a double-blind, randomized, parallel-group treatment design. After a baseline evaluation, study subjects were randomly assigned to one of the two study treatments: 1) 1450 ppm fluoride as SMFP/zinc-based dentifrice (Test) or 2) 1450 ppm fluoride as SMFP/zinc-free dentifrice (Negative Control). Subjects were provided with a soft bristle toothbrush and brushed their teeth twice daily (morning and evening) for one minute with their assigned dentifrice. After three months, and again after six months of product use, subjects returned to the testing facility for their followup gingivitis and plaque examinations. Statistical analyses were performed separately for the gingivitis assessments and dental plaque assessments using the appropriate statistical methods. All statistical tests of hypotheses were two-sided, and employed a level of significance of α = 0.05. After three and six months of product use, subjects assigned to the Test treatment exhibited statistically significant (p gingival index and plaque index scores as compared to subjects assigned to the Negative Control treatment. The results of this single-center, double-blind, parallel-group and randomized clinical study support the conclusion that a 1450 ppm fluoride as SMFP/zinc-based dentifrice provides clinically meaningful and statistically significant reductions in gingivitis (23.8%) and dental plaque (22.5%) as compared to a 1450 ppm fluoride as SMFP/zinc-free dentifrice over a six-month period of twice-daily product use.

Monitoring nitrite and nitrate residues in frankfurters during processing and storage.

Science.gov (United States)

Pérez-Rodríguez, M L; Bosch-Bosch, N; Garciá-Mata, M

1996-09-01

Frankfurter-type sausages were prepared in a pilot plant with different concentrations of NaNO(2) (75, 125 or 250 ppm) combined or not with 200 ppm KNO(3). A meat system, free of curing agents, was also used as control. Nitrite and nitrate levels were tested in various processing steps and over 120 days storage at 3 °C of the vacuum-packaged frankfurters. Little influence of the originally added nitrite level on the amount of nitrate formed was observed. Important losses of nitrite and nitrate were due to cooking. Thereafter about 50% of the nitrite added initially remained in this form in all samples (39, 59 and 146 ppm, respectively) and between 10 and 15% as nitrate. When only nitrate was initially added, formation of nitrite after cooking was observed (maximum level 43 ppm NaNO(2)). Formulations prepared with both nitrate and nitrite showed no significant differences (p nitrite or nitrate counterparts. A good correlation among nitrite and nitrate levels and storage time was showed by multiple linear regression analysis. It is concluded that the use of nitrate in combination with nitrite in cooked meat products seems to have little technological significance and adds to the total body burden of nitrite.

Separation of thorium (IV) from lanthanide concentrate (LC) and water leach purification (WLP) residue

International Nuclear Information System (INIS)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman

2014-01-01

Thorium (IV) content in industrial residue produced from rare earth elements production industry is one of the challenges to Malaysian environment. Separation of thorium from the lanthanide concentrate (LC) and Water Leach Purification (WLP) residue from rare earth elements production plant is described. Both materials have been tested by sulphuric acid and alkaline digestions. Th concentrations in LC and WLP were determined to be 1289.7 ± 129 and 1952.9±17.6 ppm respectively. The results of separation show that the recovery of Th separation from rare earth in LC after concentrated sulphuric acid dissolution and reduction of acidity to precipitate Th was found 1.76-1.20% whereas Th recovery from WLP was less than 4% after concentrated acids and alkali digestion processes. Inductively Coupled Plasma-Mass Spectroscopy (ICP-MS) was used to determine Th concentrations in aqueous phase during separation stages. This study indicated that thorium maybe exists in refractory and insoluble form which is difficult to separate by these processes and stays in WLP residue as naturally occurring radioactive material (NORM)

Total lead concentration in new decorative enamel paints in Lebanon, Paraguay and Russia.

Science.gov (United States)

Clark, C Scott; Speranskaya, Olga; Brosche, Sara; Gonzalez, Hebe; Solis, Daniela; Kodeih, Naji; Roda, Sandy; Lind, Caroline

2015-04-01

Lead concentrations in new enamel decorative paints were determined in three countries in different areas of the world where data were not previously available. The average total lead concentration of the enamel decorative paints purchased in Lebanon, Paraguay and Russia was 24,500ppm (ppm, dry weight), more than 270 times the current limit of 90ppm in Canada and in the United States. Sixty-three percent of these paints contained concentrations greater than 90ppm. Fifty-nine percent contained concentrations greater than 600ppm, the current limit in some countries. The maximum concentrations found were 236,000ppm in Lebanon, 169,000ppm in Paraguay and 52,900ppm in Russia. An average of 29% of the samples contained exceedingly high lead concentrations, >=10,000ppm. Five brands of paint were sampled in each of Lebanon and Paraguay and seven in Russia. Three colors from each brand were analyzed. For five of the six samples of the two brands in Lebanon with affiliations outside the country, the lead concentrations ranged from 1360ppm to 135,000ppm. In Lebanon the maximum concentration in the Egypt-affiliated brand (Sipes) was 135,000ppm and the maximum for the USA-affiliated brand (Dutch Boy) was 32,400ppm. Lead was not detected in any paints from the three of the four brands of paint purchased in Paraguay that had headquarters/affiliations in other countries (Brazil-Coralit), Germany (Suvinil) and USA (Novacor)). Two of the three paints from each of the other Paraguay brands contained high levels of lead with the maximum concentrations of 108,000 and 168,000ppm; one of these brands was manufactured under a license from ICI in the Netherlands. All of the paints purchased in Russia were from Russian brands and were manufactured in Russia. All three paints from one brand contained below detection levels of lead. The maximum levels of lead in the other six brands in Russia ranged from 3230 to 52,900ppm. The two brands with the highest lead concentration, TEKS and LAKRA

Protein phosphatase PPM1G regulates protein translation and cell growth by dephosphorylating 4E binding protein 1 (4E-BP1).

Science.gov (United States)

Liu, Jianyu; Stevens, Payton D; Eshleman, Nichole E; Gao, Tianyan

2013-08-09

Protein translation initiation is a tightly controlled process responding to nutrient availability and mitogen stimulation. Serving as one of the most important negative regulators of protein translation, 4E binding protein 1 (4E-BP1) binds to translation initiation factor 4E and inhibits cap-dependent translation in a phosphorylation-dependent manner. Although it has been demonstrated previously that the phosphorylation of 4E-BP1 is controlled by mammalian target of rapamycin in the mammalian target of rapamycin complex 1, the mechanism underlying the dephosphorylation of 4E-BP1 remains elusive. Here, we report the identification of PPM1G as the phosphatase of 4E-BP1. A coimmunoprecipitation experiment reveals that PPM1G binds to 4E-BP1 in cells and that purified PPM1G dephosphorylates 4E-BP1 in vitro. Knockdown of PPM1G in 293E and colon cancer HCT116 cells results in an increase in the phosphorylation of 4E-BP1 at both the Thr-37/46 and Ser-65 sites. Furthermore, the time course of 4E-BP1 dephosphorylation induced by amino acid starvation or mammalian target of rapamycin inhibition is slowed down significantly in PPM1G knockdown cells. Functionally, the amount of 4E-BP1 bound to the cap-dependent translation initiation complex is decreased when the expression of PPM1G is depleted. As a result, the rate of cap-dependent translation, cell size, and protein content are increased in PPM1G knockdown cells. Taken together, our study has identified protein phosphatase PPM1G as a novel regulator of cap-dependent protein translation by negatively controlling the phosphorylation of 4E-BP1.

Drug residues recovered in feed after various feedlot mixer truck cleanout procedures.

Science.gov (United States)

Van Donkersgoed, Joyce; Sit, Dan; Gibbons, Nicole; Ramogida, Caterina; Hendrick, Steve

2010-01-01

A study was conducted to determine the effectiveness of two methods of equipment cleanout, sequencing or flushing, for reducing drug carryover in feedlot mixer trucks. Feed samples were collected from total mixed rations before and after various feed mixer equipment cleanout procedures. Medicated rations contained either 11 ppm of tylosin or 166 or 331 ppm of chlortetracycline. There were no differences between sequencing and flushing or between flushing with dry barley and flushing with barley silage in the median proportion of drug recovered in the next ration. A larger drug reduction was achieved using flush material at a volume of 10 versus 5% of the mixer capacity and mixing the flush material for 3 versus 4 min. Regardless of the drug or prescription concentrations in the total mixed rations or the equipment cleanout procedure used, concentrations of chlortetracycline and tylosin recovered were very low.

Immune response of laying hens exposed to 30 ppm ammonia for 25 weeks

Science.gov (United States)

Ammonia is one of the most prominent aerial pollutants inside poultry production facilities, affecting chicken health and well-being based on its levels and exposure durations. The aim of this study was to investigate the effect of 30 ppm ammonia on the immune response of laying hens. Hens at 18 wk ...

The E-screen test and the MELN gene-reporter assay used for determination of estrogenic activity in fruits and vegetables in relation to pesticide residues.

Science.gov (United States)

Schilirò, Tiziana; Porfido, Arianna; Longo, Annalisa; Coluccia, Sara; Gilli, Giorgio

2013-12-01

Endocrine-disrupting chemicals (EDCs) may lead to adverse systemic effects by interfering with normal hormone homeostasis, and diet is considered to be among the main routes of EDC exposure. The present study investigated the total estrogenic activity of fruits and vegetables by calculating the 17-β-estradiol equivalent quantity (EEQ) using two in vitro tests: the human breast cancer cell line (MCF-7 BUS) proliferation assay (E-screen test) and the luciferase-transfected human breast cancer cell line (MELN) gene-reporter assay. Of the 24 analyzed fruits and vegetables, 14 contained from 1 to 4 pesticide residues in concentrations ranging from 0.02 to 1.19 ppm, whereas the other 10 did not contain any pesticide residues. The EEQ values for all positive samples ranged from 0.010 to 0.616 μg/100g for the above in vitro tests. Our study demonstrates that estrogenic activity was present in fruits and vegetables and that the concentration of allowable pesticide residues and EEQ values were positively correlated; however, no correlation was found by comparing the estrogenic activity and the intrinsic content of phytoestrogens obtained from the available literature. A theoretical adult dietary intake of 0.7-0.9 ng EEQ/L/day from fruits and vegetables was calculated. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of 0.2 ppm ozone on biomarkers of inflammation in bronchoalveolar lavage fluid and bronchial mucosa of healthy subjects

Energy Technology Data Exchange (ETDEWEB)

Krishna, M.T.; Madden, J.; Teran, L.M. [and others

1998-08-01

Short-term exposure to ozone at peak ambient levels induces neutrophil influx and impairs lung function in healthy humans. In order to investigate the mechanisms contributing to neutrophil recruitment and to examine the role of T-cells in the acute inflammatory response, we exposed 12 healthy humans to 0.2 parts per million (ppm) of ozone and filtered air on two separate occasions for 2 h with intermittent periods of rest and exercise (minute ventilation=30 L x min{sup -1}). Fibreoptic bronchoscopy was performed 6 h after the end of exposures. Total protein, tryptase, histamine, myeloperoxidase, interleukin (IL)-8 and growth-related oncogene-{alpha} (Gro-{alpha}) were measured and total and differential cell counts were performed in bronchoalveolar lavage (BAL) fluid. Flow cytometry was performed on BAL cells to study total T-cells, T-cell receptors ({alpha}{beta} and {gamma}{delta}), T-cell subsets (CD4+ and CD8+ cells) and activated T-cell subsets (CD25+). Using immunohistochemistry, neutrophils, mast cells, total T-cell numbers, T-cell subsets, CD25+ T-cells and leukocyte endothelial adhesion molecules including P-selectin, E-selectin, intercellular adhesion molecule (ICAM)-1 and vascular adhesion molecule (VCAM)-1 were quantified in the bronchial biopsies. Paired samples were available from nine subjects. Following ozone exposure there was a threefold increase in the proportion of polymorphonuclear neutrophils (PMNs) (p=0.07) and epithelial cells (p=0.05) in BAL fluid. This was accompanied by increased concentrations of IL-8 (p=0.01), Gro-{alpha} (p=0.05) and total protein (p=0.058). A significant positive correlation was demonstrated between the two chemokines and proportion of PMNs in BAL fluid. After ozone exposure there was a significant decrease in the CD4/CD8 ratio (p=0.05) and the proportion of activated CD4+ (p=001) and CD8+ T-cells (p=0.04). However, no significant changes were demonstrable in any of the inflammatory markers studied in the biopsies

Effects of neutron radiation and residual stresses on the corrosion of welds in light water reactor internals

International Nuclear Information System (INIS)

Schaaf, Bob van der; Gavillet, Didier; Lapena, Jesus; Ohms, Carsten; Roth, Armin; Dyck, Steven van

2006-01-01

After many years of operation in Light Water Reactors (LWR) Irradiation Assisted Stress Corrosion Cracking (IASCC) of internals has been observed. In particular the heat-affected zone (HAZ) has been associated with IASCC attack. The welding process induces residual stresses and micro-structural modifications. Neutron irradiation affects the materials response to mechanical loading. IASCC susceptibility of base materials is widely studied, but the specific conditions of irradiated welds are rarely assessed. Core component relevant welds of Type 304 and 347 steels have been fabricated and were irradiated in the High Flux Reactor (HFR) in Petten to 0.3 and 1 dpa (displacement per atom). In-service welds were cut from the thermal shield of the decommissioned BR-3 reactor. Residual stresses, measured using neutron diffraction, ring core tests and X-ray showed residual stress levels up to 400 MPa. Micro-structural characterization showed higher dislocation densities in the weld and HAZ. Neutron radiation increased the dislocation density, resulting in hardening and reduced fracture toughness. The sensitization degree of the welds, measured with the electrochemical potentio-dynamic reactivation method, was negligible. The Slow Strain Rate Tensile (SSRT) tests, performed at 290 deg. C in water with 200 ppb dissolved oxygen, (DO), did not reveal inter-granular cracking. Inter-granular attack of in-service steel is observed in water with 8 ppm (DO), attributed not only to IASCC, but also to IGSCC from thermal sensitization during fabrication. Stress-relieve annealing has caused Cr-grain boundary precipitation, indicating the sensitization. The simulated internal welds, irradiated up to 1.0 dpa, did not show inter-granular cracking with 8 ppm DO. (authors)

Profile of Fatty Acids, Amino Acids, Carotenoid Total, and α-Tocopherol from Flying Fish Eggs

Directory of Open Access Journals (Sweden)

Aulia Azka

2015-12-01

Full Text Available Flying fish are found in waters of eastern Indonesia, which until now is still limited informationabout nutritional content. The purpose of this research was determine the composition offatty acids, amino acids, total carotenoids, α-tocopherol flying fish eggs (Hyrundicthys sp..The composition of fatty acid was measured by gas chromatography (GC, while amino acids,total carotenoids, α-tocopherol was measured by High performanced Liquid Chromatography(HPLC. Egg contained 22 fatty acids such as saturated fatty acid 29.71%, monounsaturated fattyacid 7.86%, and polysaturated fatty acid 13.64%. The result showed that eggs flying fish contained17 amino acids, such as essential amino acid 14.96% and non-essential amino acids 20.27%. Eggscontained a total carotenoid of 245.37 ppm. α-tocopherol content of flying fish eggs by 1.06 ppm.Keywords: Amino acids, carotenoid total, fatty acid, flying fish egg, α-tocopherol

Persistence of pirimiphos methyl residues in stored wheat

International Nuclear Information System (INIS)

Zennouche, B.; Bennaceur, M.

1991-03-01

The persistence of 14C pirimiphos methyl in stored wheat was investigated under local conditions during a storage period of 6 months. Surface, methanol extractable and bound residues were quantified. There was a gradual increase in the surface residues over the storage period. 27,97% of the applied amount was found in the surface residues and 54,16% in the extractable and bound residues one month after treatment. After 6 months storage, about 17,8% of the total quantity of the applied pirimiphos methyl remained on the surface and about 58,6% was present in the grains (extractable and bound residues). During cooking 10,91% of the extractable and bound residues were lost

MONITORING AND CONTROLLING ON SURFACE SETTLEMENT IN SAND AND GRAVEL STRATA CAUSED BY SUBWAY STATION CONSTRUCTION APPLYING PIPE-ROOF PRE-CONSTRUCTION METHOD (PPM

Directory of Open Access Journals (Sweden)

Xian Yang

2017-07-01

Full Text Available Pipe-roof Pre-construction Method (PPM is regarded as a safer method to construct underground space, especially suitable for the construction sites with dense surface buildings, underground pipelines and complicated geological conditions. Xinleyizhi Station of Shenyang Metro constructed by PPM. In order to ensure safety in construction, the whole construction process was closely monitored. In this paper, monitoring results of surface settlement in PPM is analyzed. According to the monitoring results, the most serious settlement occurred in pipes jacking, which was the first and the most crucial step in PPM. The settlement reasons in each step are discussed, and controlling methods of surface settlement in each step are elaborated. Through close monitoring and timely control, the construction of Xinleyizhi Station completed smoothly. Because of the obvious advantages of PPM, the method will be used more widely in construction of shallow buried excavation under complicated surrounding and geological conditions.

Exposure to methyl tert-butyl ether, benzene, and total hydrocarbons at the Singapore-Malaysia causeway immigration checkpoint

Energy Technology Data Exchange (ETDEWEB)

Tan, C.; Ong, H.Y.; Kok, P.W. [and others

1996-12-31

The primary aim of this study was to determine the extent and levels of exposure to volatile organic compounds (VOCs) from automobile emissions in a group of immigration officers at a busy cross-border checkpoint. A majority (80%) of the workers monitored were exposed to benzene at levels between 0.01 and 0.5 ppm, with only 1.2% exceeding the current Occupational Safety and Health Administration occupational exposure limit of 1 ppm. The geometric mean (GM) concentrations of 8-hr time-weighted average exposure were 0.03 ppm, 0.9 ppm, and 2.46 ppm for methyl-tert-butyl ether (MTBE), benzene, and total hydrocarbons (THC), respectively. The highest time-weighted average concentrations measured were 1.05 ppm for MTBE, 2.01 ppm for benzene, and 34 ppm for THC. It was found that motorbikes emitted a more significant amount of pollutants compared with motor cars. On average, officers at the motorcycle booths were exposed to four to five times higher levels of VOCs (GMs of 0.07 ppm, 0.23 ppm, and 4.7 ppm for MTBE, benzene, and THC) than their counterparts at the motor car booths (GMs of 0.01 ppm, 0.05 ppm, and 1.5 ppm). The airborne concentrations of all three pollutants correlated with the flow of vehicle traffic. Close correlations were also noted for the concentrations in ambient air for the three pollutants measured. Benzene and MTBE had a correlation coefficient of 0.97. The overall findings showed that the concentrations of various VOCs were closely related to the traffic density, suggesting that they were from a common source, such as exhaust emissions from the vehicles. The results also indicated that although benzene, MTBE, and THC are known to be volatile, a significant amount could still be detected in the ambient environment, thus contributing to our exposure to these compounds. 4 refs., 6 figs.

A New On-Line Detecting Apparatus of the Residual Chlorine in Disinfectant for Fresh-Cut Vegetables

Science.gov (United States)

Hu, Chao; Su, Shu-Qiang; Li, Bao-Guo; Liu, Meng-Fang

With the fast development of modern food and beverage industry, fresh-cut vegetables have wider application than before. During the process of sterilization in fresh-cut vegetables, the concentration of chloric disinfectant is usually so high that the common sensor can't be used directly on the product line. In order to solve this problem, we have invented a new detecting apparatus which could detect high concentration of chloric disinfectant directly. In this paper, the working principle, main monitor indicators, application and technical creations of the on-line apparatus have been discussed, and we also carried on the experimental analysis for its performance. The actual demands in factory could be met when the detecting flux is 2L/min, the dilution ratio is 15 and input amount of the disinfectant is 200ml per time, the max of the detecting deviation achieves ±4.8ppm(mg/L). The main detecting range of residual chlorine is 0~300ppm.

Determination of platinum group metal catalyst residues in active pharmaceutical ingredients by means of total reflection X-ray spectrometry

International Nuclear Information System (INIS)

Marguí, Eva; Queralt, Ignasi; Hidalgo, Manuela

2013-01-01

The control of metal catalyst residues (i.e., platinum group metals (PGMs)) in different stages of the manufacturing processes of the active pharmaceutical ingredients (APIs) and, especially, in the final product is crucial. For API specimens, there are strict guidelines to limit the levels of metal residues based on their individual levels of safety concern. For PGMs the concentration limit has been established at 10 mg/kg in the API. Therefore great effort is currently being devoted to the development of new and simple procedures to control metals in pharmaceuticals. In the present work, an analytical methodology based on benchtop total reflection X-ray fluorescence spectrometry (TXRF) has been developed for the rapid and simple determination of some PGM catalyst impurities (Rh, Pd, Ir and Pt) in different types of API samples. An evaluation of different sample treatments (dissolution and digestion of the solid pharmaceutical samples) has been carried out and the developed methodologies have been validated according to the analytical parameters to be considered and acceptance criteria for PGM determination according to the United States Pharmacopeia (USP). Limits of quantification obtained for PGM metals were in the range of 2–4 mg/kg which are satisfactory according to current legislation. From the obtained results it is shown that the developed TXRF method can be implemented in the pharmaceutical industries to increase productivity of the laboratory; offering an interesting and complementary analytical tool to other atomic spectroscopic methods. - Highlights: • A TXRF method for PGM catalyst residue determination in API samples is presented. • Analysis can be performed using 10 μL of the internal standardized dissolved API. • The method is rapid, simple and suitable according to the USP requirements

High Arctic Forests During the Middle Eocene Supported by ~400 ppm Atmospheric CO2

Science.gov (United States)

Maxbauer, D. P.; Royer, D. L.; LePage, B. A.

2013-12-01

Fossils from Paleogene High Arctic deposits provide some of the clearest evidence for greenhouse climates and offer the potential to improve our understanding of Earth system dynamics in a largely ice-free world. One of the most well-known and exquisitely-preserved middle Eocene (47.9-37.8 Myrs ago) polar forest sites, Napartulik, crops out on eastern Axel Heiberg Island (80 °N), Nunavut, Canada. An abundance of data from Napartulik suggest mean annual temperatures of up to 30 °C warmer than today and atmospheric water loads 2× above current levels. Despite this wealth of paleontological and paleoclimatological data, there are currently no direct constraints on atmospheric CO2 levels for Napartulik or any other polar forest site. Here we apply a new plant gas-exchange model to Metasequoia (dawn redwood) leaves to reconstruct atmospheric CO2 from six fossil forests at Napartulik. Individual reconstructions vary between 405-489 ppm with a site mean of 437 ppm (337-564 ppm at 95% confidence). These estimates represent the first direct constraints on CO2 for polar fossil forests and suggest that the temperate conditions present at Napartulik during the middle Eocene were maintained under CO2 concentrations ~1.6× above pre-industrial levels. Our results strongly support the case that long-term climate sensitivity to CO2 in the past was sometimes high, even during largely ice-free periods, highlighting the need to better understand the climate forcing and feedback mechanisms responsible for this amplification.

Effect of humic acid on the growth, yield, nutrient composition, photosynthetic pigment and total sugar contents of peas (pisum sativum l)

International Nuclear Information System (INIS)

Khan, A.; Khan, M.Z.; Hussain, F.; Akhtar, M.E.; Gurmani, A.R.; Khan, S.

2013-01-01

Summary: A pot experiment was conducted to evaluate the effects of humic acid (HA) applied as soil and foliar at 15, 30 and 45 ppm on the growth, biochemical content, nutrient concentrations and yield of peas. Soil as well as foliar application of HA increased the plant growth and grain yield of peas; however magnitude of increase was higher in soil application than foliar. Highest plant growth and grain yield was achieved with soil application of 15 ppm HA followed by 30 ppm and foliar application of 45 ppm HA respectively. Percentage increase in dry grain yield due to 15 ppm was 37%, with 30 ppm was 29% and foliar application of 45 ppm was 25%. Nutrient concentrations (P, K, Fe, Zn, Mn and Cu) were increased with soil and foliar application of HA. The concentrations of nutrients were relatively higher in shelf than grain. Maximum concentration of P, K and Fe was obtained with the soil application of HA at 15 ppm. Humic acid applied at 15, 30 as soil as well as foliar application at 45 ppm significantly increased chlorophyll, carotenoid and total sugar content. Our results indicate that soil application of HA at 15 and 30 ppm, while foliar application at 45 ppm can increase growth, nutrients concentration, chlorophyll content and yield of Peas in calcareous soil conditions. (author)

Identification of accelerants, fuels and post-combustion residues using a colorimetric sensor array.

Science.gov (United States)

Li, Zheng; Jang, Minseok; Askim, Jon R; Suslick, Kenneth S

2015-09-07

A linear (1 × 36) colorimetric sensor array has been integrated with a pre-oxidation technique for detection and identification of a variety of fuels and post-combustion residues. The pre-oxidation method permits the conversion of fuel vapor into more detectable species and therefore greatly enhances the sensitivity of the sensor array. The pre-oxidation technique used a packed tube of chromic acid on an oxide support and was optimized in terms of the support and concentration. Excellent batch to batch reproducibility was observed for preparation and use of the disposable pre-oxidation tubes. Twenty automotive fuels including gasolines and diesel from five gasoline retailers were individually identifiable with no confusions or misclassifications in quintuplicate trials. Limits of detection were at sub-ppm concentrations for gasoline and diesel fuels. In addition, burning tests were performed on commonly used fire accelerants, and clear differentiation was achieved among both the fuels themselves and their volatile residues after burning.

Profile of Fatty Acids, Amino Acids, Carotenoid Total, and α-Tocopherol from Flying Fish Eggs

Directory of Open Access Journals (Sweden)

Aulia Azka

2015-12-01

Full Text Available Flying fish are found in waters of eastern Indonesia, which until now is still limited information about nutritional content. The purpose of this research was determine the composition of fatty acids, amino acids, total carotenoids, α-tocopherol flying fish eggs (Hyrundicthys sp.. The composition of fatty acid was measured by gas chromatography (GC, while amino acids, total carotenoids, α-tocopherol was measured by High performanced Liquid Chromatography (HPLC. Egg contained 22 fatty acids such as saturated fatty acid 29.71%, monounsaturated fatty acid 7.86%, and polysaturated fatty acid 13.64%. The result showed that eggs flying fish contained 17 amino acids, such as essential amino acid 14.96% and non-essential amino acids 20.27%. Eggs contained a total carotenoid of 245.37 ppm. α-tocopherol content of flying fish eggs by 1.06 ppm.

Intraoperative ultrasound-assisted enucleation of residual fibroids following laparoscopic myomectomy.

Science.gov (United States)

Hao, Yan; Li, Si-Jing; Zheng, Ping; Wu, Xia; Sheng, Jie; Yuan, Dong-Lan; Zhou, Qi; Wei, Wei; Duan, Ai-Hong; Wu, Qing-Qing; Lu, Dan

2018-05-25

To investigate if intraoperative ultrasounds by laparoscopic and transvaginal ultrasonography (LUS and TVS) could improve enucleating the residual fibroids following laparoscopic myomectomy (LM). From March to December 2016, 78 women with uterine fibroids underwent LM, LUS and TVS were applied to detect residual fibroids and to guide surgeons to enucleate them after the visible fibroids were removed during LM operation. The total number of residual fibroids found by LUS was 140, and the total number found by TVS was 127 following LM (P = 0.03). LUS is statistically superior to TVS in the detection of residual fibroids in the anterior wall (P = 0.004), in the detection of intramural fibroids (P = 0.002), and in the detection of fibroids with a diameter ranging from 0.5 to 1 cm (P = 0.002). According to the total number of enucleated fibroids by LM, patients were divided into three groups (Group 1: 2 to 4, Group 2: 5 to 7 and Group 3: ≥8 fibroid counts). The percentages of patients in each group with residual fibroids at the end of surgery were 22.2%, 51.9% and 66.7% respectively. Both LUS and TVS are beneficial to surgical treatment of fibroids by assisting enucleation of residual fibroids following LM, while LUS is more effective in localizing residual fibroids than TVS. Copyright © 2018 Elsevier B.V. All rights reserved.

Neutron activation analysis of biological materials for sub PPM amount of mercury without determining the chemical yield

International Nuclear Information System (INIS)

Foldzinska, A.; Dybczynski, R.

1976-01-01

A simple method for the determination of sub ppm amounts of mercury in various biological materials by neutron activation analysis is described. Irradiated samples were decomposed with H 2 SO 4 - fuming HNO 3 mixture and mercury selectively isolated by ion exchange chromatography using Dowex 50X2(H + ) and Dowex 1X4(Br - ) columns in HBr medium. Finally the activity of 197 Hg fixed on an anion exchange resin was measured either with a Ge(Li) or a NaI (Tl) detector. Both the high radiochemical purity of mercury and the practically quantitative recovery were achieved thus eliminating the necessity of determining the chemical yield. The method was used for the determination of mercury in flour, milk, butter, margarine, fish, etc. Total time of analysis (including counting) amounted to 6-7 hrs and several samples could be simultaneously analysed by one technician. (T.G.)

PROFIL PROTEIN TOTAL, ALBUMIN DAN GLOBULIN PADA AYAM BROILER YANG DIBERI KUNGIY, BAWANG PUTIH DAN ZINC (ZN

Directory of Open Access Journals (Sweden)

Sus Derthi Widhyari

2011-12-01

Full Text Available The objective of this experiment was to study the effectiveness of turmeric, garlic and zinc supplementation on protein, albumin and globulin concentration of broiler. One hundred DOC were divided into five treatments, four replications, consist of five chicks in each replicate. The treatments were R0 (basal diet as a control, R1 (R0 + 1,5% turmeric powder +2,5 % garlic powder, R2 (R0 + 2,5% garlic powder + 120 ppm zinc, R3 (R0 +1,5% turmeric powder + 120ppm zinc and R4 (R0 +1,5 turmeric powder + 2,5% garlic powder + 120 ppm zinc. The diet contain 23,5% crude protein and 3215 kcal metabolizable energy. Blood samples were taken from axillary veins at the three and six weeks of age. The results showed that total protein and globulin concentration at 6 weeks slightly higher than 3 weeks old chicks but not significantly different (P>0.05. Albumin concentration were highest on R3 treatment. Total protein and globulin concentration was highest on the R2 treatment. In conclusion, the supplementation of garlic (2.5% and ZnO (120 ppm showed the best combination to improve immune response in broiler

Flame Photometric Determination of Lithium Contents Down to 10{sup -3} ppm in Water Samples

Energy Technology Data Exchange (ETDEWEB)

Joensson, Guenther

1963-04-15

A flame photometric method has been developed for determination of submicro contents of lithium in water. The intensity of the emission from lithium increases about three times if 20 % of a mixture of acetone - amyl alcohol (4:1) is added to the sample. Interferences by stray light from sodium present is eliminated with a special absorption filter. Interferences from oxide bands of the alkaline earth metals are completely suppressed after adding aluminium to the sample. With the development of this routine method it is possible by flame photometry to directly determine 0.01 ppm lithium with an error of analysis less than 10 %. Furthermore the investigation shows that, after concentration of the sample by evaporation, contents down to 10{sup -3} ppm can be determined without any difficulty. One person can run up to 50 determinations per day.

Determination of PCBs in fish using enzyme-linked immunosorbent assay (ELISA)

Science.gov (United States)

Lasrado, J.A.; Santerre, C.R.; Zajicek, J.L.; Stahl, J.R.; Tillitt, D.E.; Deardorff, D.

2003-01-01

Polychlorinated biphenyls (PCBs) were determined in fish tissue using an enzyme-linked immunosorbent assay (ELISA). Standard curves for Aroclor 1248, 1254, and 1260 in catfish tissue were developed with ranges from 0.05 to 0.5 ppm and 0.5 to 5.0 ppm. Wild fish were initially analyzed using gas chromatography/electron-capture detection (GC/ECD) and those having residues within the standard curve ranges were analyzed with ELISA. Results obtained using ELISA and GC/ECD were not significantly different (p < 0.05) from 0.05 to 0.5 ppm. From 0.5 to 5.0 ppm, the standard curve for Aroclor 1254 was the best predictor of total PCB in wild fish samples.

The effect of elevated CO2 and N on decomposition of wheat straw and alfalfa residues in calcareous and non calcareous soils

Directory of Open Access Journals (Sweden)

S. Razavi Darbar

2016-04-01

Full Text Available Incorporation of plant residue in soils is considered as an important agricultural practice for maintaining soil fertility in sustainable agricultural system. CO2 levels, nitrogen fertilization and plant residues are factors which highly affect decomposition of added organic matter to soil. In this research controlled chambers were used to investigate the effects of elevated atmospheric CO2 concentrations (350 vs. 760 CO2 ppm under two N fertilization levels (0 vs. 500 kg N ha-1 and two replicates on decomposition of wheat and alfalfa residues in two calcareous (32.66 % CaCO3 and non calcareous soils (3.4 % CaCO3 at 6 times (0, 10, 20, 40, 60 and 90 under laboratory condition. Soil moistures were adjusted at 70% of field capacity. The results showed that elevated CO2 significantly increased decomposition of residues in both calcareous and non calcareous soils. In the samples that received N fertilizer, decomposition of wheat straw and alfalfa residues increased in both soils. From the obtained results, we concluded that in all treatments the amount of decomposition of wheat straw and alfalfa residues in calcareous soil were higher than non calcareous soils.

Tracking the spring migration of a bar-headed goose (Anser indicus) across the Himalaya with satellite telemetry

Science.gov (United States)

Javed, Sàlim; Takekawa, John Y.; Douglas, David C.; Rahmani, Asad R.; Kanai, Yutaka; Nagendran, Meenakshi; Choudhury, Binod C.; Sharma, Shruti

2000-01-01

Soil-food-chain-pesticide wildlife relationships were investigated to learn the concentration of pesticide residues present in soils, macro-invertebrates, vertebrates, and seeds as a result of annual applications of aldrin at recommended rates for pest control. Two central Missouri cornfields treated witb aldrin at 1 lb/acre, for 16 and 15 of the past 17 years, were selected for study during 1965-67. Primary samples collected for residue analyses included soils, earthworms (Lumbricidae), crickets (GryIlidae), and two kinds of ground beetles (Carabidae) obtained during early April, June, August, and October. Vertebrates and plant seeds collected during 1967 included white-footed mice (Peromyscus maniculatus), toads (Bufo americanus), snakes (Thamnophis sirtalis and Pituophis sayi), corn (Zea Mays), foxtail (Setaria Faberii), and annual sunflower (Helianthus annuus). Pesticide residues consisted primarily of dieldrin, the degradation product of aldrin. Combined aldrin and dieldrin residues, as two field all-season averages, wet weight basis, were: soils, 0.31 ppm; earthworms, 1.49 ppm; crickets, 0.23 ppm; Harpalus ground beetles, 1.10 ppm; Poecilus ground beetles, 9.67 ppm; white-footed mice, 0.98 ppm; toads, 3.53 ppm; garter snakes, 12.35 ppm; and corn, foxtail, and sunflower seeds less than 0.02 ppm each. Unusually high average residues (37.48 ppm) in Poecilus beetles during June, 1967, were attributed to abnormally high soil moisture and predacious feeding habits of these insects.

Soil-food chain-pesticide wildlife relationships in aldrin-treated fields

Science.gov (United States)

Korschgen, L.J.

1970-01-01

Soil-food-chain-pesticide wildlife relationships were investigated to learn the concentration of pesticide residues present in soils, macro-invertebrates, vertebrates, and seeds as a result of annual applications of aldrin at recommended rates for pest control. Two central Missouri cornfields treated witb aldrin at 1 lb/acre, for 16 and 15 of the past 17 years, were selected for study during 1965-67. Primary samples collected for residue analyses included soils, earthworms (Lumbricidae), crickets (GryIlidae), and two kinds of ground beetles (Carabidae) obtained during early April, June, August, and October. Vertebrates and plant seeds collected during 1967 included white-footed mice (Peromyscus maniculatus), toads (Bufo americanus), snakes (Thamnophis sirtalis and Pituophis sayi), corn (Zea Mays), foxtail (Setaria Faberii), and annual sunflower (Helianthus annuus). Pesticide residues consisted primarily of dieldrin, the degradation product of aldrin. Combined aldrin and dieldrin residues, as two field all-season averages, wet weight basis, were: soils, 0.31 ppm; earthworms, 1.49 ppm; crickets, 0.23 ppm; Harpalus ground beetles, 1.10 ppm; Poecilus ground beetles, 9.67 ppm; white-footed mice, 0.98 ppm; toads, 3.53 ppm; garter snakes, 12.35 ppm; and corn, foxtail, and sunflower seeds less than 0.02 ppm each. Unusually high average residues (37.48 ppm) in Poecilus beetles during June, 1967, were attributed to abnormally high soil moisture and predacious feeding habits of these insects.

Mobility of organic carbon from incineration residues

International Nuclear Information System (INIS)

Ecke, Holger; Svensson, Malin

2008-01-01

Dissolved organic carbon (DOC) may affect the transport of pollutants from incineration residues when landfilled or used in geotechnical construction. The leaching of dissolved organic carbon (DOC) from municipal solid waste incineration (MSWI) bottom ash and air pollution control residue (APC) from the incineration of waste wood was investigated. Factors affecting the mobility of DOC were studied in a reduced 2 6-1 experimental design. Controlled factors were treatment with ultrasonic radiation, full carbonation (addition of CO 2 until the pH was stable for 2.5 h), liquid-to-solid (L/S) ratio, pH, leaching temperature and time. Full carbonation, pH and the L/S ratio were the main factors controlling the mobility of DOC in the bottom ash. Approximately 60 weight-% of the total organic carbon (TOC) in the bottom ash was available for leaching in aqueous solutions. The L/S ratio and pH mainly controlled the mobilization of DOC from the APC residue. About 93 weight-% of TOC in the APC residue was, however, not mobilized at all, which might be due to a high content of elemental carbon. Using the European standard EN 13 137 for determination of total organic carbon (TOC) in MSWI residues is inappropriate. The results might be biased due to elemental carbon. It is recommended to develop a TOC method distinguishing between organic and elemental carbon

Further studies on the use of enzyme profiles to monitor residue accumulation in wildlife: Plasma enzymes in starlings fed graded concentrations of morsodren, DDE, Aroclor 1254, and malathion

Science.gov (United States)

Dieter, M.P.

1975-01-01

Wild-trapped starlings (Sturnus vulgaris) were fed concentrations of Morsodren (2, 4, and 8 ppm), DDE or Aroclor 1254 (5, 25, and 100 ppm), or malathion (8, 35, and 160 ppm) that were found to be sublethal in pen-reared Coturnix quail fed these amounts for 12 weeks. Plasma enzymes had to be measured earlier than planned in starlings fed Morsodren (at three weeks) or the organochlorine compounds (at seven weeks) because of unexpected, subsequent mortality. Variations in enzyme response were greater in wild than in pen-reared birds, but not enough to mask the toxicant-induced changes in enzyme activity. Cholinesterase activities decreased in birds fed Morsodren or malathion, and increased in those fed the organochlorine compounds. Lactate dehydrogenase activities increased two-fold in starlings fed Morsodren and two- to four-fold in those fed the organochlorine compounds, but only 50% in those fed malathion. Further examination of enzyme profiles showed that creatine kinase and aspartate aminotransferase activities increased two-to four-fold in birds fed Morsodren or the organochlorine compounds but not at all in those fed malathion. Thus the classes of environmental contaminants fed to starlings could be easily distinguished by these enzymatic parameters. Evaluation of enzymatic profiles appears to be a potentially valuable technique to monitor the presence of toxicants in wild populations, especially if used to complement standard chemical residue analyses. Here the residue analyses showed, after three weeks feeding, that mercury in the carcasses reflected the concentrations fed daily, whereas accumulation in the livers was two- to four-fold greater. After seven weeks feeding, liver residues of either organochlorine compound were about three-fold higher than the concentrations fed daily. However, four times as much DDE as Aroclor 1254 had accumulated in the carcasses.

Characterization and monitoring of total organic chloride vapors

International Nuclear Information System (INIS)

Anheier, N.C. Jr.; Evans, J.C. Jr.; Olsen, K.B.

1992-07-01

Chemical sensors are being developed intermediate highly selective and broadly selective methods. PNL is developing an optical-emission based TOCl (total organic chlorinated compounds) sensor (Halosnif) which is capable of measuring TOCl in real time on an extracted gas sample over a wide linear dynamic range. Halosnif employs an atomic emission sensor that is broadly selective for any moderately volatile organic hclorinated vapor but does not distinguish between classes of chlorinated compounds. A rf-induced He plasma is used to excite the chlorine atoms, causing light emission at 837.6 nm. The sensitivity ranges from 1-2 ppM up to at least 10,000 ppM. Field tests were conducted at Tinker AFB in areas of high TCE contamination, in two boreholes at Savannah River, and at Hanford CCl 4 vapor extraction system. This sensor is briefly compared with acoustic wave sensors being developed by SNL (PAWS). 4 figs

Toxic metal residues in Philippine foods

International Nuclear Information System (INIS)

Sumera, F.; Verceluz, F.; Kapauan, P.A.; Sembrite, E.

1976-03-01

Mercury introduced into the environment will cause death or irreparable damage to man. Surveillance of mercury in foods especially fish has become important in the Philippines since rivers, oceans, and lakes have become dumping sites for industrial and mining wastes. Mercury analysis on a total of 52 fish and shellfish samples were undertaken using the cold vapour atomic absorption spectrophotometry. All of the samples have mercury contents of less than the maximum permissible level of 0.5 ppm. Comparison was made with analysis of shark samples which are predators and consequently contain much higher levels of mercury than the non-predators

Two transcription factors TaPpm1 and TaPpb1 co-regulate anthocyanin biosynthesis in purple pericarps of wheat

Science.gov (United States)

Jiang, Wenhui; Liu, Tianxiang; Nan, Wenzhi; Jeewani, Diddugodage Chamila; Niu, Yanlu; Li, Chunlian; Shi, Xue; Wang, Cong; Wang, Jiahuan; Li, Yang; Wang, Zhonghua

2018-01-01

Abstract Purple pericarps of bread wheat (Triticum aestivum L.) are a useful source of dietary anthocyanins. Previous mapping results indicated that the purple pericarp trait is controlled by two complementary genes located on chromosomes 7D and 2A. However, the identity of the genes and the mechanisms by which they regulate the trait are unknown. In this study, two transcription factors were characterised as anthocyanin activators in purple pericarps: TaPpm1 (purple pericarp-MYB 1) and TaPpb1 (purple pericarp-bHLH 1). Three non-functional variants were detected in the coding sequence of TaPpm1 from non-purple seed lines, in which the function of TaPpm1 was destroyed either by insertion-induced frame shifts or truncated peptides. There were six 261-bp tandem repeats in the promoter region of TaPpb1 in the purple-grained varieties, while there was only one repeat unit present in the non-purple varieties. Furthermore, using yeast two-hybrid, dual luciferase, yeast one-hybrid, and transient assays, we were able to demonstrate that the interaction of TaPpm1 and TaPpb1 co-regulates the synthesis of anthocyanin. Overall, our results provide a better understanding of the molecular basis of anthocyanin synthesis in the wheat pericarp and indicate the existence of an integrated regulatory mechanism that controls production. PMID:29562292

Effect of dog food containing 460 ppm fluoride on rat reproduction.

Science.gov (United States)

Marks, T A; Schellenberg, D; Metzler, C M; Oostveen, J; Morey, M J

1984-01-01

A one-generation, two-litter rat reproduction study was done in a kennel in Allegan County, Michigan, as part of an investigation of reproductive problems in Shetland sheepdogs (shelties). Since 1970, at least 115 sheltie litters at this kennel have been grossly deformed and/or have died, generally within 3 d of birth. The causative factor(s) appears to be associated with the environment, as the shelties have had successful pregnancies elsewhere. There was some concern that a potential threat to human reproduction also might exist in this area. After it was discovered that fluoride in the dog food had apparently caused mottled teeth and bony exostoses in dogs at this and at least two other kennels, dog-food fluoride content and local well water were investigated as possible causes of the reproductive problems. A two-way factorial statistical design allowed assessment of dietary fluoride content and water source and interaction between the two. UPj:TUC(SD)spf rats, 9 males and 18 females in each group, were assigned to treatment with high-fluoride dog food (460 ppm) and well water; high-fluoride dog food and distilled water; low-fluoride dog food (56 ppm) and well water; and low-fluoride dog food and distilled water. After 60 d in the kennel, the rats were mated. Even after two litters, the only adverse effect was dental fluorosis in the high-fluoride groups. The results indicated that rats cannot be used in the search for the cause(s) of reproductive problems in dogs in this kennel.

Heparin sodium compliance to USP monograph: structural elucidation of an atypical 2.18 ppm NMR signal.

Science.gov (United States)

Mourier, Pierre A J; Guichard, Olivier Y; Herman, Fréderic; Viskov, Christian

2012-01-01

The ¹H nuclear magnetic resonance (NMR) acceptance criteria in the new heparin US Pharmacopeia (USP) monograph do not take into account potential structural modifications responsible for any extra signals observed in ¹H NMR spectra, some purified heparins may be non-compliant under the proposed new USP guidelines and incorrectly classified as unsuitable for pharmaceutical use. Heparins from the "ES" source, containing an extra signal at 2.18 ppm, were depolymerized under controlled conditions using heparinases I, II, and III. The oligosaccharides responsible for the 2.18 ppm signal were enriched using orthogonal chromatographic techniques. After multiple purification steps, we obtained an oligosaccharide mixture containing a highly enriched octasaccharide bearing the structural modification responsible for the extra signal. Following heparinase I depolymerization, a pure tetrasaccharide containing the fingerprint structural modification was isolated for full structural determination. Using 1D and 2D ¹H NMR spectroscopy, the structural moiety responsible for the extra signal at 2.18 ppm was identified as an acetyl group on the heparin backbone, most likely resulting from a very minor manufacturing process side reaction that esterifies the uronic acid at position 3. Such analytical peculiarity has always been present in this heparin source and it was used safety over the years. Copyright © 2012 Elsevier B.V. All rights reserved.

Distribution of Total Volatile Organic Compounds at taxi drivers in Tehran

Directory of Open Access Journals (Sweden)

Seyyed Mohammad Javad Golhosseini

2015-06-01

Full Text Available Air pollution is currently the most serious environmental health threat worldwide. Volatile Organic Compounds (VOC are considered as the main effective factors in causing air pollution. Vehicles are among the major sources which emit these compounds, so it seems that automobiles’ microenvironment is one of the places where people are exposed to high concentration of VOC. Evaluating the exposure amount of Total Volatile Organic Compounds (TVOC can indeed be used as an indicator to estimate the amount of exposure to every individual VOC. This study was conducted on the concentration of TVOC inside Tehran taxies for a period of one year. For this purpose, a real time instrument equipped with photo-ionization detector (PID was used. Consequently, the highest and the lowest measured TVOC in taxies equaled 3.33 ppm and 0.72 ppm, respectively. In addition, the arithmetic mean of TVOC concentration was 1.77±0.53 ppm inside the examined taxies. In this study, the parameters like measurement time, climate and vehicle conditions were found to have significant effect on the amount of exposure to TVOC.

Determination of insecticides malathion and lambda-cyhalothrin residues in zucchini by gas chromatography

Directory of Open Access Journals (Sweden)

Hayam M. Lofty

2013-12-01

Full Text Available A sensitive gas chromatographic method has been developed for the determination of malathion and lambda-cyhalothrin (λ-cyhalothrin insecticide residues in zucchini. The developed method consists of extraction with acetone, purification and partitioning with methylene chloride, column chromatographic clean-up, and finally capillary gas chromatographic determination of the insecticides. The recoveries of method were greater than 90% and limit of determination was 0.001 ppm for both insecticides. The method was applied to determine residues and the rate of disappearance of malathion and λ-cyhalothrin from fruits of zucchini (open field treatment, 50 cc of Malason/Cormandel 57% EC (emulsifiable concentrate for 100 L of water, 20 cc of LAMBDA SUPER FOG 5% liquid for 100 L of water. The insecticide incorporated into the plants decreased rapidly with a half-life time around 0.77 day (18.5h for malathion and 4 days for λ-cyhalothrin. It is not recommended to use zucchini before 12 h of malathion application. For λ-cyhalothrin, the preharvest interval is 5 days. Four market samples were chosen from different regions from A.R.E. and all of them showed no residues of malathion or λ-cyhalothrin.

Evaluation of gas chromatography – electron ionization – full scan high resolution Orbitrap mass spectrometry for pesticide residue analysis

International Nuclear Information System (INIS)

Mol, Hans G.J.; Tienstra, Marc; Zomer, Paul

2016-01-01

Gas chromatography with electron ionization and full scan high resolution mass spectrometry with an Orbitrap mass analyzer (GC-EI-full scan Orbitrap HRMS) was evaluated for residue analysis. Pesticides in fruit and vegetables were taken as an example application. The relevant aspects for GC-MS based residue analysis, including the resolving power (15,000 to 120,000 FWHM at m/z 200), scan rate, dynamic range, selectivity, sensitivity, analyte identification, and utility of existing EI-libraries, are assessed and discussed in detail. The optimum acquisition conditions in full scan mode (m/z 50–500) were a resolving power of 60,000 and an automatic-gain-control target value of 3E6. These conditions provided (i) an optimum mass accuracy: within 2 ppm over a wide concentration range, with/without matrix, enabling the use of ±5 ppm mass extraction windows (ii) adequate scan speed: minimum 12 scans/peak, (iii) an intra-scan dynamic range sufficient to achieve LOD/LOQs ≤0.5 pg in fruit/vegetable matrices (corresponding to ≤0.5 μg kg"−"1) for most pesticides. EI-Orbitrap spectra were consistent over a very wide concentration range (5 orders) with good match values against NIST (EI-quadrupole) spectra. The applicability for quantitative residue analysis was verified by validation of 54 pesticides in three matrices (tomato, leek, orange) at 10 and 50 μg/kg. The method involved a QuEChERS-based extraction with a solvent switch into iso-octane, and 1 μL hot splitless injection into the GC-HRMS system. A recovery between 70 and 120% and a repeatability RSD <10% was obtained in most cases. Linearity was demonstrated for the range ≤5–250 μg kg"−"1. The pesticides could be identified according to the applicable EU criteria for GC-HRMS (SANTE/11945/2015). GC-EI-full scan Orbitrap HRMS was found to be highly suited for quantitative pesticide residue analysis. The potential of qualitative screening to extend the scope makes it an attractive alternative to

Evaluation of gas chromatography – electron ionization – full scan high resolution Orbitrap mass spectrometry for pesticide residue analysis

Energy Technology Data Exchange (ETDEWEB)

Mol, Hans G.J., E-mail: hans.mol@wur.nl; Tienstra, Marc; Zomer, Paul

2016-09-07

Gas chromatography with electron ionization and full scan high resolution mass spectrometry with an Orbitrap mass analyzer (GC-EI-full scan Orbitrap HRMS) was evaluated for residue analysis. Pesticides in fruit and vegetables were taken as an example application. The relevant aspects for GC-MS based residue analysis, including the resolving power (15,000 to 120,000 FWHM at m/z 200), scan rate, dynamic range, selectivity, sensitivity, analyte identification, and utility of existing EI-libraries, are assessed and discussed in detail. The optimum acquisition conditions in full scan mode (m/z 50–500) were a resolving power of 60,000 and an automatic-gain-control target value of 3E6. These conditions provided (i) an optimum mass accuracy: within 2 ppm over a wide concentration range, with/without matrix, enabling the use of ±5 ppm mass extraction windows (ii) adequate scan speed: minimum 12 scans/peak, (iii) an intra-scan dynamic range sufficient to achieve LOD/LOQs ≤0.5 pg in fruit/vegetable matrices (corresponding to ≤0.5 μg kg{sup −1}) for most pesticides. EI-Orbitrap spectra were consistent over a very wide concentration range (5 orders) with good match values against NIST (EI-quadrupole) spectra. The applicability for quantitative residue analysis was verified by validation of 54 pesticides in three matrices (tomato, leek, orange) at 10 and 50 μg/kg. The method involved a QuEChERS-based extraction with a solvent switch into iso-octane, and 1 μL hot splitless injection into the GC-HRMS system. A recovery between 70 and 120% and a repeatability RSD <10% was obtained in most cases. Linearity was demonstrated for the range ≤5–250 μg kg{sup −1}. The pesticides could be identified according to the applicable EU criteria for GC-HRMS (SANTE/11945/2015). GC-EI-full scan Orbitrap HRMS was found to be highly suited for quantitative pesticide residue analysis. The potential of qualitative screening to extend the scope makes it an attractive

PPM-One: a static protein structure based chemical shift predictor

International Nuclear Information System (INIS)

Li, Dawei; Brüschweiler, Rafael

2015-01-01

We mined the most recent editions of the BioMagResDataBank and the protein data bank to parametrize a new empirical knowledge-based chemical shift predictor of protein backbone atoms using either a linear or an artificial neural network model. The resulting chemical shift predictor PPM-One accepts a single static 3D structure as input and emulates the effect of local protein dynamics via interatomic steric contacts. Furthermore, the chemical shift prediction was extended to most side-chain protons and it is found that the prediction accuracy is at a level allowing an independent assessment of stereospecific assignments. For a previously established set of test proteins some overall improvement was achieved over current top-performing chemical shift prediction programs

Residual nilpotence and residual solubility of groups

International Nuclear Information System (INIS)

Mikhailov, R V

2005-01-01

The properties of the residual nilpotence and the residual solubility of groups are studied. The main objects under investigation are the class of residually nilpotent groups such that each central extension of these groups is also residually nilpotent and the class of residually soluble groups such that each Abelian extension of these groups is residually soluble. Various examples of groups not belonging to these classes are constructed by homological methods and methods of the theory of modules over group rings. Several applications of the theory under consideration are presented and problems concerning the residual nilpotence of one-relator groups are considered.

High-voltage measurements on the 5 ppm relative uncertainty level with collinear laser spectroscopy

Science.gov (United States)

Krämer, J.; König, K.; Geppert, Ch; Imgram, P.; Maaß, B.; Meisner, J.; Otten, E. W.; Passon, S.; Ratajczyk, T.; Ullmann, J.; Nörtershäuser, W.

2018-04-01

We present the results of high-voltage collinear laser spectroscopy measurements on the 5 ppm relative uncertainty level using a pump and probe scheme at the 4s ^2S1/2 → 4p ^2P3/2 transition of {\\hspace{0pt}}40Ca+ involving the 3d ^2D5/2 metastable state. With two-stage laser interaction and a reference measurement we can eliminate systematic effects such as differences in the contact potentials due to different electrode materials and thermoelectric voltages, and the unknown starting potential of the ions in the ion source. Voltage measurements were performed between  -5 kV and  -19 kV and parallel measurements with stable high-voltage dividers calibrated to 5 ppm relative uncertainty were used as a reference. Our measurements are compatible with the uncertainty limits of the high-voltage dividers and demonstrate an unprecedented (factor of 20) increase in the precision of direct laser-based high-voltage measurements.

PPM-based System for Guided Waves Communication Through Corrosion Resistant Multi-wire Cables

Science.gov (United States)

Trane, G.; Mijarez, R.; Guevara, R.; Pascacio, D.

Novel wireless communication channels are a necessity in applications surrounded by harsh environments, for instance down-hole oil reservoirs. Traditional radio frequency (RF) communication schemes are not capable of transmitting signals through metal enclosures surrounded by corrosive gases and liquids. As an alternative to RF, a pulse position modulation (PPM) guided waves communication system has been developed and evaluated using a corrosion resistant 4H18 multi-wire cable, commonly used to descend electronic gauges in down-hole oil applications, as the communication medium. The system consists of a transmitter and a receiver that utilizes a PZT crystal, for electrical/mechanical coupling, attached to each extreme of the multi-wire cable. The modulator is based on a microcontroller, which transmits60 kHz guided wave pulses, and the demodulator is based on a commercial digital signal processor (DSP) module that performs real time DSP algorithms. Experimental results are presented, which were obtained using a 1m corrosion resistant 4H18multi-wire cable, commonly used with downhole electronic gauges in the oil sector. Although there was significant dispersion and multiple mode excitations of the transmitted guided wave energy pulses, the results show that data rates on the order of 500 bits per second are readily available employing PPM and simple communications techniques.

Identification of homemade inorganic explosives by ion chromatographic analysis of post-blast residues.

Science.gov (United States)

Johns, Cameron; Shellie, Robert A; Potter, Oscar G; O'Reilly, John W; Hutchinson, Joseph P; Guijt, Rosanne M; Breadmore, Michael C; Hilder, Emily F; Dicinoski, Greg W; Haddad, Paul R

2008-02-29

Anions and cations of interest for the post-blast identification of homemade inorganic explosives were separated and detected by ion chromatographic (IC) methods. The ionic analytes used for identification of explosives in this study comprised 18 anions (acetate, benzoate, bromate, carbonate, chlorate, chloride, chlorite, chromate, cyanate, fluoride, formate, nitrate, nitrite, perchlorate, phosphate, sulfate, thiocyanate and thiosulfate) and 12 cations (ammonium, barium(II), calcium(II), chromium(III), ethylammonium, magnesium(II), manganese(II), methylammonium, potassium(I), sodium(I), strontium(II), and zinc(II)). Two IC separations are presented, using suppressed IC on a Dionex AS20 column with potassium hydroxide as eluent for anions, and non-suppressed IC for cations using a Dionex SCS 1 column with oxalic acid/acetonitrile as eluent. Conductivity detection was used in both cases. Detection limits for anions were in the range 2-27.4ppb, and for cations were in the range 13-115ppb. These methods allowed the explosive residue ions to be identified and separated from background ions likely to be present in the environment. Linearity (over a calibration range of 0.05-50ppm) was evaluated for both methods, with r(2) values ranging from 0.9889 to 1.000. Reproducibility over 10 consecutive injections of a 5ppm standard ranged from 0.01 to 0.22% relative standard deviation (RSD) for retention time and 0.29 to 2.16%RSD for peak area. The anion and cation separations were performed simultaneously by using two Dionex ICS-2000 chromatographs served by a single autoinjector. The efficacy of the developed methods was demonstrated by analysis of residue samples taken from witness plates and soils collected following the controlled detonation of a series of different inorganic homemade explosives. The results obtained were also confirmed by parallel analysis of the same samples by capillary electrophoresis (CE) with excellent agreement being obtained.

Metabolomic database annotations via query of elemental compositions: Mass accuracy is insufficient even at less than 1 ppm

Directory of Open Access Journals (Sweden)

Fiehn Oliver

2006-04-01

Full Text Available Abstract Background Metabolomic studies are targeted at identifying and quantifying all metabolites in a given biological context. Among the tools used for metabolomic research, mass spectrometry is one of the most powerful tools. However, metabolomics by mass spectrometry always reveals a high number of unknown compounds which complicate in depth mechanistic or biochemical understanding. In principle, mass spectrometry can be utilized within strategies of de novo structure elucidation of small molecules, starting with the computation of the elemental composition of an unknown metabolite using accurate masses with errors Results High mass accuracy (95% of false candidates. This orthogonal filter can condense several thousand candidates down to only a small number of molecular formulas. Example calculations for 10, 5, 3, 1 and 0.1 ppm mass accuracy are given. Corresponding software scripts can be downloaded from http://fiehnlab.ucdavis.edu. A comparison of eight chemical databases revealed that PubChem and the Dictionary of Natural Products can be recommended for automatic queries using molecular formulae. Conclusion More than 1.6 million molecular formulae in the range 0–500 Da were generated in an exhaustive manner under strict observation of mathematical and chemical rules. Assuming that ion species are fully resolved (either by chromatography or by high resolution mass spectrometry, we conclude that a mass spectrometer capable of 3 ppm mass accuracy and 2% error for isotopic abundance patterns outperforms mass spectrometers with less than 1 ppm mass accuracy or even hypothetical mass spectrometers with 0.1 ppm mass accuracy that do not include isotope information in the calculation of molecular formulae.

Corn Residue Use by Livestock in the United States

Directory of Open Access Journals (Sweden)

Marty R. Schmer

2017-01-01

Full Text Available Corn ( L. residue grazing or harvest provides a simple and economical practice to integrate crops and livestock, but limited information is available on how widespread corn residue utilization is practiced by US producers. In 2010, the USDA Economic Research Service surveyed producers from 19 states on corn grain and residue management practices. Total corn residue grazed or harvested was 4.87 million ha. Approximately 4.06 million ha was grazed by 11.7 million livestock (primarily cattle in 2010. The majority of grazed corn residue occurred in Nebraska (1.91 million ha, Iowa (385,000 ha, South Dakota (361,000 ha, and Kansas (344,000 ha. Average grazing days ranged from 10 to 73 d (mean = 40 d. Corn residue harvests predominantly occurred in the central and northern Corn Belt, with an estimated 2.9 Tg of corn residue harvested across the 19 states. This survey highlights the importance of corn residue for US livestock, particularly in the western Corn Belt.

The fungicidal and phytotoxic properties of benomyl and PPM in supplemented agar media supporting transgenic arabidopsis plants for a Space Shuttle flight experiment

Science.gov (United States)

Paul, A. L.; Semer, C.; Kucharek, T.; Ferl, R. J.

2001-01-01

Fungal contamination is a significant problem in the use of sucrose-enriched agar-based media for plant culture, especially in closed habitats such as the Space Shuttle. While a variety of fungicides are commercially available, not all are equal in their effectiveness in inhibiting fungal contamination. In addition, fungicide effectiveness must be weighed against its phytotoxicity and in this case, its influence on transgene expression. In a series of experiments designed to optimize media composition for a recent shuttle mission, the fungicide benomyl and the biocide "Plant Preservative Mixture" (PPM) were evaluated for effectiveness in controlling three common fungal contaminants, as well as their impact on the growth and development of arabidopsis seedlings. Benomyl proved to be an effective inhibitor of all three contaminants in concentrations as low as 2 ppm (parts per million) within the agar medium, and no evidence of phytotoxicity was observed until concentrations exceeded 20 ppm. The biocide mix PPM was effective as a fungicide only at concentrations that had deleterious effects on arabidopsis seedlings. As a result of these findings, a concentration of 3 ppm benomyl was used in the media for experiment PGIM-01 which flew on shuttle Columbia mission STS-93 in July 1999.

Harvesting and handling agricultural residues for energy

Energy Technology Data Exchange (ETDEWEB)

Jenkins, B.M.; Summer, H.R.

1986-05-01

Significant progress in understanding the needs for design of agricultural residue collection and handling systems has been made but additional research is required. Recommendations are made for research to (a) integrate residue collection and handling systems into general agricultural practices through the development of multi-use equipment and total harvest systems; (b) improve methods for routine evaluation of agricultural residue resources, possibly through remote sensing and image processing; (c) analyze biomass properties to obtain detailed data relevant to engineering design and analysis; (d) evaluate long-term environmental, social, and agronomic impacts of residue collection; (e) develop improved equipment with higher capacities to reduce residue collection and handling costs, with emphasis on optimal design of complete systems including collection, transportation, processing, storage, and utilization; and (f) produce standard forms of biomass fuels or products to enhance material handling and expand biomass markets through improved reliability and automatic control of biomass conversion and other utilization systems. 118 references.

Use of Bioassay test for the environmental evaluation of mining residues and their leachates: the singular case of the Portman Bay (SE, Spain)

Science.gov (United States)

Martínez-Sánchez, Maria Jose; García-Lorenzo, Maria Luz; Pérez-Sirvent, Carmen; Molina, Jose; Tudela, Maria Luz; Hernández-Córdoba, Manuel

2010-05-01

The aim of the present study was to evaluate the toxicity of sediments and their pore-water extracts from sites contaminated by mining activities using two assays: bacteria and plants. The acute toxicity in pore-waters was determined using the Microtox® bioassay, which uses the naturally luminescent marine bacterium Vibrio fischeri. Phytotoxicity in soil samples was tested by way of the seed germination and root elongation technique in three plant species, Sorghum saccharatum, Sinapis alba and Lepidium sativum. The aim of applying these assays is to establish a method for evaluating the real risks within a risk analysis process, considering both present and future risks, bearing in mind that the uses to which soil is put (urban, recreational or industrial) may change. In the zone studied, mining activities have led to heavy metal contamination with the risk of runoff and wind dispersion of the contaminated material. For this study, 6 sediment samples were collected from Portman Bay (Murcia, SE Spain). The soil extract was prepared by saturation with distilled water and allowing it to stand for four hours. Then, the soil was subjected to a vacuum pressure to extract the soil solution through filter paper. The Zn and Fe content was determined by flame atomic absorption spectrometry (FAAS). The Pb, Cd and Cu content was determined by electrothermal atomization atomic absorption spectrometry (ETAAS). The As content was analysed by atomic fluorescence spectrometry using an automated continuous flow hydride generation (As-AFS) spectrometer. Total Pb concentration varied from 600 to 2500 ppm, with a mean value of 1200 ppm. The average content of Zn was 5300 ppm. The mean concentration of Cd and Cu was 23 and 59 ppm, respectively. Total As concentrations varied from 180 to 470 ppm, with an average value 280 ppm. Finally, the total Fe content ranged from 37% to 47%, with an average value of 40%. Pore-water samples showed neutral pH values and average electrical

Assay development status report for total cyanide

International Nuclear Information System (INIS)

Simpson, B.C.; Jones, T.E.; Pool, K.H.

1993-02-01

A validated cyanide assay that is applicable to a variety of tank waste matrices is necessary to resolve certain waste tank safety issues and for purposes of overall waste characterization. The target for this effort is an assay with an applicable range of greater than 1,000 ppM (0.10 wt%) total cyanide and a confidence level greater than 80%. Figure 1 illustrates the operating regime of the proposed cyanide assay method. The Assay Development Status Report for Total Cyanide will summarize the past experience with cyanide analyses on-tank waste matrices and will rate the status of the analytical methods used to assay total cyanide (CN - ion) in the tank waste matrices as acceptable or unacceptable. This paper will also briefly describe the current efforts for improving analytical resolution of the assays and the attempts at speciation

Solow Residuals Without Capital Stocks

DEFF Research Database (Denmark)

Burda, Michael C.; Severgnini, Battista

2014-01-01

We use synthetic data generated by a prototypical stochastic growth model to assess the accuracy of the Solow residual (Solow, 1957) as a measure of total factor productivity (TFP) growth when the capital stock in use is measured with error. We propose two alternative measurements based on curren...

Effects of dressing and cooking on DDT concentrations in certain fish from Lake Michigan

Science.gov (United States)

Reinert, Robert E.; Stewart, Donald; Seagran, Harry L.

1972-01-01

Concentrations of DDT residues were highest in parts of the body with the highest oil content in four species of fish from Lake Michigan: yellow perch (Perca flavescens), bloater (Coregonus hoyi), lake trout (Salvelinus namaycush), and coho salmon (Oncorhynchus kisutch). Dressing reduced the DDT residues and oil content by more than 90% in yellow perch but had little effect in the other three species. The concentration of DDT residues in bloaters was changed little by smoking but was reduced 64–72% by other methods of cooking: from 8.0 ppm (raw) to 2.2 ppm after frying in corn oil; from 10.7 to 3.9 ppm after frying in lard; and from 9.1 to 3.2 ppm after broiling. The concentration of DDT residues in fillets of yellow perch changed only from 0.3 ppm (raw) to 0.4 or 0.5 ppm after baking, frying, or broiling.

Total mercury concentrations in lionfish (Pterois volitans/miles) from the Florida Keys National Marine Sanctuary, USA.

Science.gov (United States)

Huge, Dane H; Schofield, Pamela J; Jacoby, Charles A; Frazer, Thomas K

2014-01-15

Strategies to control invasive lionfish in the western Atlantic and Caribbean are likely to include harvest and consumption. Until this report, total mercury concentrations had been documented only for lionfish from Jamaica, and changes in concentrations with increasing fish size had not been evaluated. In the Florida Keys, total mercury concentrations in dorsal muscle tissue from 107 lionfish ranged from 0.03 to 0.48 ppm, with all concentrations being less than the regulatory threshold for limited consumption. Mercury concentrations did not vary consistently with standard lengths or wet weights of lionfish. In 2010, lionfish from the upper Keys had mean concentrations that were 0.03-0.04 ppm higher than lionfish from the middle Keys, but mean concentrations did not differ consistently among years and locations. Overall, total mercury concentrations in lionfish were lower than those in several predatory fishes that support commercial and recreational fisheries in Florida. Published by Elsevier Ltd.

Polarographic determination of Sn (II) and total Sn in PYRO and MDP radiopharmaceutical kits

International Nuclear Information System (INIS)

Sebastian, Maria V.A.; Lugon, Marcelo Di M.V.; Silva, Jose L. da; Fukumori, Neuza T.O.; Pereira, Nilda P.S. de; Silva, Constancia P.G. da; Matsuda, Margareth M.N.

2007-01-01

A sensitive, alternative method to atom absorption spectrometry, fluorimetry or potentiometry for the evaluation of tin(II) ions (0.1- 10 mg) and total tin in radiopharmaceutical kits was investigated. Differential pulse polarography was chosen. The supporting electrolyte was H 2 SO 4 3 mol L -1 and HCl 3 mol L -1 solution. The potential was swept from -250 to -800 mV vs Ag/AgCl/saturated KCl, using a dropping mercury electrode with 1 s drop time, 50 mV s -1 scan rate, -50 mV pulse amplitude, 40 ms pulse time and 10 mV step amplitude. Pure nitrogen was used to deaerate the polarographic cell solution for 5 min, before and after each sample introduction. Oxidation of Sn(II) was made in the same sample vial by adding H 2 O 2 (hydrogen peroxide) 10 mol L -1 , at 37 deg C, in order to quantify the total Sn. The calibration curve for Sn(II) and Sn(IV) was obtained in the concentration range of 0-10 ppm from a 1000 ppm standard solution. The detection limit of Sn(II) is 0.5 ppm and for Sn(IV) is 0.6 ppm. Differential pulse polarography was performed in the pyrophosphate (PYRO) and methylenediphosphonic acid (MDP) radiopharmaceutical kits, containing 2 mg and 1 mg of SnCl 2 .2H 2 O per vial, respectively. The described method for determination of stannous ion (Sn(II)), is selective, reproducible and adequate to be used in the quality control of lyophilized reagents and it shall be performed for other cold kits produced at IPEN. (author)

Nitrous oxide emission from soils amended with crop residues

NARCIS (Netherlands)

Velthof, G.L.; Kuikman, P.J.; Oenema, O.

2002-01-01

Crop residues incorporated in soil are a potentially important source of nitrous oxide (N2O), though poorly quantified. Here, we report on the N2O emission from 10 crop residues added to a sandy and a clay soil, both with and without additional nitrate (NO3-). In the sandy soil, total nitrous oxide

Biostimulation of soil polluted 10000 ppm of waste motor oil and phytoremediation with Cicer arietinum improved by Bacillus cereus/Rhizobium etli

Directory of Open Access Journals (Sweden)

Juárez-Cisneros Gladys

2016-08-01

Full Text Available Soil pollution by waste motor oil (WMO is reducing its productivity. An alternative for removing WMO from soil is by biostimulation (BIS applying animal manure and then phytoremediation (PR by legume improving with plant growth promoting bacteria (PGPB to reduce WMO concentration at level below 4400 ppm limit permit for the NOM-138-SEMARNAT/SSA1-2012 (NOM-138. The aims of this re-search were: i to analyze soil biostimulation polluted by 10000 ppm of WMO applying vermicompost, then subsequent soil phytoremediation with Cicer arietinum inoculated by Bacillus cereus and/or Rhizo-bium etli. In soil after applying BS by VC was measured WMO soil concentration and ii for PR was regarded phenology and biomass of C. arietinum and WMO concentration remaining at the end of this step. The results showed that soil biostimulated by VC, WMO was reduced at 1370 ppm, subsequent PR sowing C. arietinum with R. etli, WMR was reduced at 30 ppm concentration both values below to maxi-mum value accepted by NOM-138. Those data indicate that in soil polluted by WMO the best way to biorecovery soil was to integrate strategy BS/PR the last one improved by genus of PGPB.

Vision for utilization of livestock residue as bioenergy resource in Japan

International Nuclear Information System (INIS)

Fujino, Junichi; Morita, Akihiro; Matsuoka, Yasunari; Sawayama, Shigeki

2005-01-01

Utilization of livestock residue is important not only for energy recovery and material recycling but also for preventing environmental pollution. This paper focuses on the following options from the viewpoint of the Law on Promoting Proper Management and Use of Livestock Excreta and the Kyoto protocol: energy use from livestock residue, reductions in CO 2 emissions resulting from substitution of fossil fuels, and reduction of other greenhouse gas emissions through appropriate treatment of livestock residue. Bioenergy potential of livestock residue in Japan was estimated to be 167 PJ in the year 2000. This is equivalent to about 0.7% of total primary energy supply. Biogas production with methane fermentation and burning poultry residue at power plants can produce 4.1 TWh of electricity and 46 PJ of heat. The amount of CO 2 substitution for fossil fuels is 6.9 Mt-CO 2 . This corresponds to about 0.6% of total CO 2 emissions in 1990. This also has an additional effect of reducing other greenhouse gas (CH 4 and N 2 O) emissions from conventional treatment of livestock residue. Development of biogas plants, promotion of biogas utilization, and effective use of fertilizer components extracted from livestock residue are expected to gain importance in the future

Acid transformation of bauxite residue: Conversion of its alkaline characteristics

OpenAIRE

Kong, X.; Li, M.; Xue, S.; Hartley, W.; Chen, C.; Wu, C.; Li, X.; Li, Y.

2016-01-01

Bauxite residue (BR) is a highly alkaline solid hazardous waste produced from bauxite processing for alumina production. Alkaline transformation appears to reduce the environmental risk of bauxite residue disposal areas (BRDAs) whilst potentially providing opportunities for the sustainable reuse and on-going management of BR. Mineral acids, a novel citric acid and a hybrid combination of acid-gypsum treatments were investigated for their potential to reduce residue pH and total alkalinity and...

Measurement of fluorine total concentration in dental enamel using fast neutron activation

International Nuclear Information System (INIS)

Mouadili, A.; Vernais, J.; Isabelle, D.B.

1988-01-01

Fluorine which is present in dental enamel, at the level of a few tens to a few hundred ppm, plays an important role in the behaviour of this tissue. Therefore quantitative determination is of interest for particular studies of the dental system. We present a nuclear nondestructive method to determine the total fluorine content in dental enamel by cyclotron-produced fast-neutron activation. The 19 F(n,2n) reaction leads to 18 F which is a β + emitter with a 109.8 min half-life. The irradiated sample activity is measured by detecting in coincidence the annihilation photons. A fluorine standard is used for calibration. The detection limit is of the order of 1 ppm, while the reproducibility is better than 95% [pt

Naturally Occurring Radioactive Materials in Uranium-Rich Coals and Associated Coal Combustion Residues from China.

Science.gov (United States)

Lauer, Nancy; Vengosh, Avner; Dai, Shifeng

2017-11-21

Most coals in China have uranium concentrations up to 3 ppm, yet several coal deposits are known to be enriched in uranium. Naturally occurring radioactive materials (NORM) in these U-rich coals and associated coal combustion residues (CCRs) have not been well characterized. Here we measure NORM (Th, U, 228 Ra, 226 Ra, and 210 Pb) in coals from eight U-rich coal deposits in China and the associated CCRs from one of these deposits. We compared NORM in these U-rich coals and associated CCRs to CCRs collected from the Beijing area and natural loess sediments from northeastern China. We found elevated U concentrations (up to 476 ppm) that correspond to low 232 Th/ 238 U and 228 Ra/ 226 Ra activity ratios (≪1) in the coal samples. 226 Ra and 228 Ra activities correlate with 238 U and 232 Th activities, respectively, and 226 Ra activities correlate well with 210 Pb activities across all coal samples. We used measured NORM activities and ash yields in coals to model the activities of CCRs from all U-rich coals analyzed in this study. The activities of measured and modeled CCRs derived from U-rich coals exceed the standards for radiation in building materials, particularly for CCRs originating from coals with U > 10 ppm. Since beneficial use of high-U Chinese CCRs in building materials is not a suitable option, careful consideration needs to be taken to limit potential air and water contamination upon disposal of U- and Ra-rich CCRs.

Effects of 0.12 and 0.80 PPM ozone on rat nasal and nasopharyngeal epithelial mucosubstances: Quantitative histochemistry

International Nuclear Information System (INIS)

Harkema, J.R.; Hotchkiss, J.A.; Henderson, R.F.

1988-01-01

The present study was designed to characterize changes in the quantity of mucosubstances in surface epithelia of rat nasal airways after short- term ozone exposure. Rats were exposed for 7 days (6 h/day) to 0.0, 0.12, or 0.8 ppm ozone, and killed immediately or 7 days after the last exposure. Nasal cavities were processed for morphometric analysis of intraepithelial mucosubstances. Compared to controls, rats exposed to 0.12 ppm ozone had increased amounts of stored mucosubstances within epithelium lining the medial aspect of the nasal turbinate immediately after exposure, but no change within epithelia of the nasopharynx. Rats exposed to 0.8 ppm ozone had increased quantities of stored mucosubstances within transitional and respiratory epithelium lining turbinates and lateral walls of the anterior nasal airway and significant decreases in stored mucosubstances within epithelia of the nasal septum at the end of exposure. Seven days after the end of exposure, the amounts of intraepithelial mucosubstances returned to control levels along the septum, but remained greater than those of controls along the turbinates. We demonstrated that exposures to ambient levels of ozone induce significant changes in the stored secretory product of nasal epithelium in the rat, and that these changes persist for at least 7 days post-exposure. (author)

Biorremediation of soil polluted by 75000 ppm of waste motor oil applying biostimulation and phytoremediation with Sorghum vulgare and Bacillus cereus or Burkholderia cepacia

Directory of Open Access Journals (Sweden)

Balderas-León Iván

2015-02-01

Full Text Available Waste motor oil (WMO pollutes soil and causing lost soil fertility. An alternative to solve this problem its bioremediation (BR by double and following biostimulation (BS with mineral solution (MS and a legume as green manure (GM then using phytoremediation (PR with growth promoting vegetal bacteria (GPVB like Bacillus cereus and Burkholderia cepacia to minimize remaining WMO. The aims of this research were: a bioremediation of polluted soil by 75000 ppm of WMO by biostimulation and then b Its phytoremediation for remaining WMO by Sorghum vulgare inoculated with B. cereus and B. cepacia. Soil polluted by high concentration WMO was biostimulated with MS, and then Phaseolus vulgaris treated by GPVB was incorporated as GM, finally to apply PR to eliminate WMO with S. vulgare with GPVB. Results indicate that soil bioremediated by biostimulation with MS, WMO decreased at 32500 ppm/30 days, and then with GM, WMO was reduced at 10100 ppm after/90 days. Finally, to apply phytoremediation using S. vulgare and GPVB at flowering, WMO was reduced from 2500 ppm to 800 ppm. For recovering soil impacted by high concentration WMO to apply both techniques double and following BS and PR are the best option than each technique separately.

Quadratic residues and non-residues selected topics

CERN Document Server

Wright, Steve

2016-01-01

This book offers an account of the classical theory of quadratic residues and non-residues with the goal of using that theory as a lens through which to view the development of some of the fundamental methods employed in modern elementary, algebraic, and analytic number theory. The first three chapters present some basic facts and the history of quadratic residues and non-residues and discuss various proofs of the Law of Quadratic Reciprosity in depth, with an emphasis on the six proofs that Gauss published. The remaining seven chapters explore some interesting applications of the Law of Quadratic Reciprocity, prove some results concerning the distribution and arithmetic structure of quadratic residues and non-residues, provide a detailed proof of Dirichlet’s Class-Number Formula, and discuss the question of whether quadratic residues are randomly distributed. The text is a valuable resource for graduate and advanced undergraduate students as well as for mathematicians interested in number theory.

Parametric Study for MOV Performance Improvement Using PPM Program

Energy Technology Data Exchange (ETDEWEB)

Lee, Seungho; Seon, Juhyoung; Han, Bongsub [SOOSAN INDUSTRIES, Seoul (Korea, Republic of)

2016-10-15

Nuclear power plants mainly use Air Operated Valve(hereinafter referred to as AOV) and Motor Operator Valve(hereinafter referred to as MOV) for protecting system, blocking and controlling flow. Field test(static, dynamic test) results and performance prediction program are used to evaluate if MOV currently installed on nuclear power plants has the operational performance. The improvement of operating performance for Flexible Gate valve was confirmed on changing input variables of performance program(PPM). here are several methods through reviewing design basis, changes operating procedures and maintenance work of stem(or packing, etc.) to improve operating performance of MOV generally installed in the nuclear power plants. This study verified the changes of the MOV operating performance through the improvement of stem and hydraulic parts(seat, guide etc.). Especially, MOV operating performance was much greater improved when the Disk Seat Angle was decreasing. Generally, improvement work to minimize friction of seat, disk and guide is limited and dynamic diagnostic testing has to be performed with change in valve factor for improvement of hydraulic parts.

Robust fault detection of turbofan engines subject to adaptive controllers via a Total Measurable Fault Information Residual (ToMFIR) technique.

Science.gov (United States)

Chen, Wen; Chowdhury, Fahmida N; Djuric, Ana; Yeh, Chih-Ping

2014-09-01

This paper provides a new design of robust fault detection for turbofan engines with adaptive controllers. The critical issue is that the adaptive controllers can depress the faulty effects such that the actual system outputs remain the pre-specified values, making it difficult to detect faults/failures. To solve this problem, a Total Measurable Fault Information Residual (ToMFIR) technique with the aid of system transformation is adopted to detect faults in turbofan engines with adaptive controllers. This design is a ToMFIR-redundancy-based robust fault detection. The ToMFIR is first introduced and existing results are also summarized. The Detailed design process of the ToMFIRs is presented and a turbofan engine model is simulated to verify the effectiveness of the proposed ToMFIR-based fault-detection strategy. Copyright © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

Fuzzy control of optical PPM CDMA with M-ary orthogonal signaling

Science.gov (United States)

Cui, K.; Leeson, M. S.; Hines, E. L.

2008-06-01

This paper introduces an incorporated spectral-amplitude coding (SAC) optical code-division multiple-access (OCDMA) scheme. One novel class of optical signature codes based on combinatorial designs is employed with M-ary pulse-position modulation (PPM) signaling to improve the system performance beyond the interference limit. A union upper bound on the bit error rate (BER) is derived and the performance characteristics are then discussed with a variety of system parameters. Furthermore, fuzzy logic (FL) control is proposed to provide tolerance of different degrees of reliability in multirate transmission and to achieve distinct service differentiation for multimedia applications. It is shown that the proposed system can effectively suppress noise effects and offer improved adaptation capabilities for multi-quality network requirements in comparison with systems without optimization.

Newton-Gauss Algorithm of Robust Weighted Total Least Squares Model

Directory of Open Access Journals (Sweden)

WANG Bin

2015-06-01

Full Text Available Based on the Newton-Gauss iterative algorithm of weighted total least squares (WTLS, a robust WTLS (RWTLS model is presented. The model utilizes the standardized residuals to construct the weight factor function and the square root of the variance component estimator with robustness is obtained by introducing the median method. Therefore, the robustness in both the observation and structure spaces can be simultaneously achieved. To obtain standardized residuals, the linearly approximate cofactor propagation law is employed to derive the expression of the cofactor matrix of WTLS residuals. The iterative calculation steps for RWTLS are also described. The experiment indicates that the model proposed in this paper exhibits satisfactory robustness for gross errors handling problem of WTLS, the obtained parameters have no significant difference with the results of WTLS without gross errors. Therefore, it is superior to the robust weighted total least squares model directly constructed with residuals.

Evaluation of pesticide residues in fruits and vegetables from Algeria.

Science.gov (United States)

Mebdoua, Samira; Lazali, Mohamed; Ounane, Sidi Mohamed; Tellah, Sihem; Nabi, Fahima; Ounane, Ghania

2017-06-01

A total of 160 samples of 13 types of fresh fruits and vegetables from domestic production and import were analysed to detect the presence of pesticide residues. Analysis was performed by multi-residual extraction followed by gas chromatography-mass spectrometry. In 42.5% of the tested samples, no residues were found and 12.5% of samples contained pesticide residues above maximum residue limits. Risk assessment for long-term exposure was done for all pesticides detected in this study. Except chlorpyrifos and lambda-cyhalothrin, exposure to pesticides from vegetables and fruits was below 1% of the acceptable daily intake. Short-term exposure assessment revealed that in seven pesticide/commodity combinations, including three pesticides (chlorpyrifos, deltamethrin and lambda-cyhalothrin), the acute reference dose had been exceeded.

γ-Oryzanol and tocopherol contents in residues of rice bran oil refining.

Science.gov (United States)

Pestana-Bauer, Vanessa Ribeiro; Zambiazi, Rui C; Mendonça, Carla R B; Beneito-Cambra, Miriam; Ramis-Ramos, Guillermo

2012-10-01

Rice bran oil (RBO) contains significant amounts of the natural antioxidants γ-oryzanol and tocopherols, which are lost to a large degree during oil refining. This results in a number of industrial residues with high contents of these phytochemicals. With the aim of supporting the development of profitable industrial procedures for γ-oryzanol and tocopherol recovery, the contents of these phytochemicals in all the residues produced during RBO refining were evaluated. The samples included residues from the degumming, soap precipitation, bleaching earth filtering, dewaxing and deodorisation distillation steps. The highest phytochemical concentrations were found in the precipitated soap for γ-oryzanol (14.2 mg g(-1), representing 95.3% of total γ-oryzanol in crude RBO), and in the deodorisation distillate for tocopherols (576 mg 100 g(-1), representing 6.7% of total tocopherols in crude RBO). Therefore, among the residues of RBO processing, the deodorisation distillate was the best source of tocopherols. As the soap is further processed for the recovery of fatty acids, samples taken from every step of this secondary process, including hydrosoluble fraction, hydrolysed soap, distillation residue and purified fatty acid fraction, were also analyzed. The distillation residue left after fatty acid recovery from soap was found to be the best source of γ-oryzanol (43.1 mg g(-1), representing 11.5% of total γ-oryzanol in crude RBO). Copyright © 2012 Elsevier Ltd. All rights reserved.

Study on the relation between uranium content and total phosphorus in some sudanese phosphate ore samples

International Nuclear Information System (INIS)

Eltayeb, M. A. H.; Mohammed, A. A.

2003-01-01

In the present work uranium content and total phosphorus were determined in 30 phosphate ore samples collected from Kurun and Uro areas in Nuba Mountains in Sudan. Spectrophotometry technique was used for this purpose. Uranium analysis is based on the use of nitrogen (V) acid for leaching the rock, and treatment with ammonium carbonate solution, whereby uranium (Vi) is kept in solution as its carbonate complex. The ion exchange technique was used for the recovery of uranium. Uranium was eluted from the resin with 1 M hydrochloric acid. In the elute, uranium was determined spectrophotometrically by measurement of absorbance of the yellow uranium (Vi)-8-hydroxyquinolate complex at λ 400 nm. The total phosphorus was measured as (P 2 O 5 %) by treatment of the total liquor with ammonium molybdate solution. The absorbance of the blue complex was measured at λ 880 nm. The results show that a limited relation is existed between uranium content and total phosphorus in phosphate samples from kurun area, which contain 58.8 ppm uranium in average, where there are no relation is existed in phosphate samples from uro area, which contain 200 ppm uranium in average. (Author)

A summary of total mercury concentrations in flora and fauna near common contaminant sources in the Gulf of Mexico.

Science.gov (United States)

Lewis, M; Chancy, C

2008-02-01

Total mercury concentrations are summarized for environmental media and biota collected from near-coastal areas, several impacted by contaminant sources common to the Gulf of Mexico. Water, sediment, fish, blue crabs, oysters, clams, mussels, periphyton and seagrasses were collected during 1993-2002 from targeted areas affected by point and non-point source contaminants. Mean concentrations in water and sediment were 0.02 (+/-1 standard deviation=0.06) microg l(-1) and 96.3 (230.8) ng g(-1) dry wt, respectively. Mean total mercury concentrations in fish, blue crabs, brackish clams and mussels were significantly greater than those in sediment, seagrass, colonized periphyton and oysters. Concentrations (ng g(-1) dry wt) averaged 23.1 (two seagrass species), 220.1 (oysters), 287.8 (colonized periphyton), 604.0 (four species of freshwater mussels), 772.4 (brackish clam), 857.9 (blue crabs) and 933.1 (nine fish species). Spatial, intraspecific and interspecific variability in results limited most generalizations concerning the relative mercury contributions of different stressor types. However, concentrations were significantly greater for some biota collected from areas receiving wastewater discharges and golf course runoff (fish), agricultural runoff (oysters) and urban stormwater runoff (colonized periphyton and sediment). Marine water quality criteria and proposed sediment quality guidelines were exceeded in 1-12% of total samples. At least one seafood consumption guideline, criteria or screening value were exceeded in edible tissues of blue crabs (6% total samples) and nine fish species (8-33% total samples) but all residues were less than the US Federal Drug Administration action limit of 1.0 ppm and the few reported toxic effect concentrations available for the targeted biota.

Forensic analysis of high explosives residues in post-blast water samples employing solid phase extraction for analyte pro-concentration

International Nuclear Information System (INIS)

Umi Kalsom Ahmad; Rajendran, Sumathy; Ling, Lee Woan

2008-01-01

Nitro aromatic, nitramine and nitrate ester compounds are a major group of high order explosive or better known as military explosives. Octahydro-1,3,5,7-tetrazocine (HMX), 1,3,5-hexahydro-1,3,5-trinitro triazine (RDX), 2,4,6-trinitro-toluene (TNT), pentaerythritol tetranitrate (PETN) and 2,4-dinitrotoluene (2,4-DNT) are secondary high explosives classified as most commonly used explosives components. There is an increasing demand for pre-concentration of these compounds in water samples as the sensitivity achieved by instrumental analytical methods for these high explosives residues are the main drawback in the application at trace levels for forensic analysis. Hence, a simple cartridge solid phase extraction (SPE) procedure was optimized as the off-line extraction and pre-concentration method to enhance the detection limit of high explosive residues using micellar electrokinetic chromatography (MEKC) and gas chromatography with electron-capture detection (GC-ECD) methods. The SPE cartridges utilized LiChrolut EN as the SPE adsorbent. By emplying pre-concentration using SPE, the detection limits of the target analytes in water sample were lowered by more than 1000 times with good percentage recovery (>87%) for MEKC method and lowered by 120 times with more than 2 % percentage recovery for GC-ECD methods. In order to test the feasibility of the developed method to real cases, post-blast water samples were analyzed. The post-blast water samples which were collected from Baling Bom training range, Ulu Kinta, Perak contained RDX and PETN in the range of 0.05 - 0.17 ppm and 0.0124 - 0.0390 ppm respectively. (author)

Residual gravimetric method to measure nebulizer output.

Science.gov (United States)

Vecellio None, Laurent; Grimbert, Daniel; Bordenave, Joelle; Benoit, Guy; Furet, Yves; Fauroux, Brigitte; Boissinot, Eric; De Monte, Michele; Lemarié, Etienne; Diot, Patrice

2004-01-01

The aim of this study was to assess a residual gravimetric method based on weighing dry filters to measure the aerosol output of nebulizers. This residual gravimetric method was compared to assay methods based on spectrophotometric measurement of terbutaline (Bricanyl, Astra Zeneca, France), high-performance liquid chromatography (HPLC) measurement of tobramycin (Tobi, Chiron, U.S.A.), and electrochemical measurements of NaF (as defined by the European standard). Two breath-enhanced jet nebulizers, one standard jet nebulizer, and one ultrasonic nebulizer were tested. Output produced by the residual gravimetric method was calculated by weighing the filters both before and after aerosol collection and by filter drying corrected by the proportion of drug contained in total solute mass. Output produced by the electrochemical, spectrophotometric, and HPLC methods was determined after assaying the drug extraction filter. The results demonstrated a strong correlation between the residual gravimetric method (x axis) and assay methods (y axis) in terms of drug mass output (y = 1.00 x -0.02, r(2) = 0.99, n = 27). We conclude that a residual gravimetric method based on dry filters, when validated for a particular agent, is an accurate way of measuring aerosol output.

Long-term stabilization of crop residues and soil organic carbon affected by residue quality and initial soil pH.

Science.gov (United States)

Wang, Xiaojuan; Butterly, Clayton R; Baldock, Jeff A; Tang, Caixian

2017-06-01

Residues differing in quality and carbon (C) chemistry are presumed to contribute differently to soil pH change and long-term soil organic carbon (SOC) pools. This study examined the liming effect of different crop residues (canola, chickpea and wheat) down the soil profile (0-30cm) in two sandy soils differing in initial pH as well as the long-term stability of SOC at the amended layer (0-10cm) using mid-infrared (MIR) and solid-state 13 C nuclear magnetic resonance (NMR) spectroscopy. A field column experiment was conducted for 48months. Chickpea- and canola-residue amendments increased soil pH at 0-10cm in the Podzol by up to 0.47 and 0.36units, and in the Cambisol by 0.31 and 0.18units, respectively, at 48months when compared with the non-residue-amended control. The decomposition of crop residues was greatly retarded in the Podzol with lower initial soil pH during the first 9months. The MIR-predicted particulate organic C (POC) acted as the major C sink for residue-derived C in the Podzol. In contrast, depletion of POC and recovery of residue C in MIR-predicted humic organic C (HOC) were detected in the Cambisol within 3months. Residue types showed little impact on total SOC and its chemical composition in the Cambisol at 48months, in contrast to the Podzol. The final HOC and resistant organic C (ROC) pools in the Podzol amended with canola and chickpea residues were about 25% lower than the control. This apparent priming effect might be related to the greater liming effect of these two residues in the Podzol. Copyright © 2017 Elsevier B.V. All rights reserved.

PENGGUNAAN Aspergilus niger YANG DIRADIASI GAMMA SEBAGAI BIOREMEDIAN RESIDU TRIAZOFOS DAN LOGAM BERAT PADA BAWANG MERAH (Allium cepa L.

Directory of Open Access Journals (Sweden)

Beny Maulana Satria

2015-06-01

Full Text Available The use of pesticides and fertilizers containing Pb in agriculture will leave residues in soil, water, and plants. This Pb will be accumulated in the human body and, have a negative impact gradually on human health. The use of gamma-irradiation of Aspergillus niger is expected to reduce the levels of metals and residues triazofos onions. Bioremediation technique using gamma rays against a. niger is still quite a bit or a new research so the research on this is still a little The purpose of this study was to determine the effectiveness of technology A. niger low dose gamma irradiation in reducing heavy metals and low triazofos residue on onion. Apergillus niger low dose gamma irradiated, mixed with organic materials such as Kohe, rice husk and bran. The mixture is fermented for 8 days and then applied to the soil of onion in Bradford to measure levels of Pb and triazofosnya residue. The Atomic Absorption Spectrophotometer (AAS and Gas Chromatography Mass Spectrophotometer (GCMS was used in this study. The result showed Pb that goes into the water very small and more are stuck in the ground and Pb accumulated in onion is still quite high. Triazofos residue concentrations in onions undetectable or very low in quality standards established under 0,005 ppm. The conclusion of this study, Aspergillus niger were not irradiated and irradiated can withstand heavy metals Pb in soil so it goes into the water a little, but not optimal in Pb which adsorbs into the onion and pesticide residues on onions Triazofos undetected.Keywords: Aspergillus niger, residual triazofos, gamma radiation, onion

Influence of ageing of residues on the availability of herbicides for leaching

International Nuclear Information System (INIS)

Walker, A.; Rodriguez-Cruz, M.S.; Mitchell, M.J.

2005-01-01

Losses by leaching of chlorotoluron, isoproturon and triasulfuron from small intact columns of a structured clay loam and an unstructured sandy loam soil were measured in five separate field experiments. In general, losses of all three herbicides were greater from the clay loam than from the sandy loam soil and the order between herbicides was always triasulfuron>>isoproturon>chlorotoluron. Differences between experiments were also consistent for every soil/herbicide combination. There was no relationship between total loss and either total rainfall or cumulative leachate volume. When weighting factors were applied to the rainfall data to make early rainfall more important than later rainfall, there were significant positive relationships between cumulative weighted rainfall and total losses. Also, there were significant negative correlations between total losses and the delay to accumulation of 25 mm rainfall (equivalent to one pore volume of available water) in the different experiments. In laboratory incubations, there was a more rapid decline in aqueous (0.01 M calcium chloride) extractable residues than in total solvent extractable residues indicating increasing sorption with residence time. However, the rate of change in water extractable residues could not completely explain the decrease in leachability with ageing of residues in the field. Short-term sorption studies with aggregates of the two soils indicated slower sorption by those of the clay loam than by those of the sandy loam suggesting that diffusion into and out of aggregates may affect availability for leaching in the more structured soil. Small scale leaching studies with aggregates of the soils also demonstrated reductions in availability for leaching as residence time in soil was increased, which could not be explained by degradation. These results therefore indicate that time-dependent sorption processes are important in controlling pesticide movement in soils, although the data do not give a

Influence of ageing of residues on the availability of herbicides for leaching

Energy Technology Data Exchange (ETDEWEB)

Walker, A.; Rodriguez-Cruz, M.S.; Mitchell, M.J

2005-01-01

Losses by leaching of chlorotoluron, isoproturon and triasulfuron from small intact columns of a structured clay loam and an unstructured sandy loam soil were measured in five separate field experiments. In general, losses of all three herbicides were greater from the clay loam than from the sandy loam soil and the order between herbicides was always triasulfuron>>isoproturon>chlorotoluron. Differences between experiments were also consistent for every soil/herbicide combination. There was no relationship between total loss and either total rainfall or cumulative leachate volume. When weighting factors were applied to the rainfall data to make early rainfall more important than later rainfall, there were significant positive relationships between cumulative weighted rainfall and total losses. Also, there were significant negative correlations between total losses and the delay to accumulation of 25 mm rainfall (equivalent to one pore volume of available water) in the different experiments. In laboratory incubations, there was a more rapid decline in aqueous (0.01 M calcium chloride) extractable residues than in total solvent extractable residues indicating increasing sorption with residence time. However, the rate of change in water extractable residues could not completely explain the decrease in leachability with ageing of residues in the field. Short-term sorption studies with aggregates of the two soils indicated slower sorption by those of the clay loam than by those of the sandy loam suggesting that diffusion into and out of aggregates may affect availability for leaching in the more structured soil. Small scale leaching studies with aggregates of the soils also demonstrated reductions in availability for leaching as residence time in soil was increased, which could not be explained by degradation. These results therefore indicate that time-dependent sorption processes are important in controlling pesticide movement in soils, although the data do not give a

Automated determination of the stable carbon isotopic composition (δ13C) of total dissolved inorganic carbon (DIC) and total nonpurgeable dissolved organic carbon (DOC) in aqueous samples: RSIL lab codes 1851 and 1852

Science.gov (United States)

Révész, Kinga M.; Doctor, Daniel H.

2014-01-01

The purposes of the Reston Stable Isotope Laboratory (RSIL) lab codes 1851 and 1852 are to determine the total carbon mass and the ratio of the stable isotopes of carbon (δ13C) for total dissolved inorganic carbon (DIC, lab code 1851) and total nonpurgeable dissolved organic carbon (DOC, lab code 1852) in aqueous samples. The analysis procedure is automated according to a method that utilizes a total carbon analyzer as a peripheral sample preparation device for analysis of carbon dioxide (CO2) gas by a continuous-flow isotope ratio mass spectrometer (CF-IRMS). The carbon analyzer produces CO2 and determines the carbon mass in parts per million (ppm) of DIC and DOC in each sample separately, and the CF-IRMS determines the carbon isotope ratio of the produced CO2. This configuration provides a fully automated analysis of total carbon mass and δ13C with no operator intervention, additional sample preparation, or other manual analysis. To determine the DIC, the carbon analyzer transfers a specified sample volume to a heated (70 °C) reaction vessel with a preprogrammed volume of 10% phosphoric acid (H3PO4), which allows the carbonate and bicarbonate species in the sample to dissociate to CO2. The CO2 from the reacted sample is subsequently purged with a flow of helium gas that sweeps the CO2 through an infrared CO2 detector and quantifies the CO2. The CO2 is then carried through a high-temperature (650 °C) scrubber reactor, a series of water traps, and ultimately to the inlet of the mass spectrometer. For the analysis of total dissolved organic carbon, the carbon analyzer performs a second step on the sample in the heated reaction vessel during which a preprogrammed volume of sodium persulfate (Na2S2O8) is added, and the hydroxyl radicals oxidize the organics to CO2. Samples containing 2 ppm to 30,000 ppm of carbon are analyzed. The precision of the carbon isotope analysis is within 0.3 per mill for DIC, and within 0.5 per mill for DOC.

76 FR 38158 - Withdrawal of Pesticide Petitions for Residues of Pesticide Chemicals in or on Various Commodities

Science.gov (United States)

2011-06-29

....5 ppm; cattle, kidney at 5.0 ppm; cattle, liver at 2.0 ppm; cattle, meat and cattle meat byproducts at 0.40 ppm; goat, fat at 1.5 ppm; goat, kidney at 5.0 ppm; goat, liver, at 2.0 ppm; goat, meat and goat, meat byproducts at 0.40 ppm; hog, fat at 1.5 ppm; hog, kidney at 5.0 ppm; hog, liver at 2.0 ppm...

Calculus of the Power Spectral Density of Ultra Wide Band Pulse Position Modulation Signals Coded with Totally Flipped Code

Directory of Open Access Journals (Sweden)

DURNEA, T. N.

2009-02-01

Full Text Available UWB-PPM systems were noted to have a power spectral density (p.s.d. consisting of a continuous portion and a line spectrum, which is composed of energy components placed at discrete frequencies. These components are the major source of interference to narrowband systems operating in the same frequency interval and deny harmless coexistence of UWB-PPM and narrowband systems. A new code denoted as Totally Flipped Code (TFC is applied to them in order to eliminate these discrete spectral components. The coded signal transports the information inside pulse position and will have the amplitude coded to generate a continuous p.s.d. We have designed the code and calculated the power spectral density of the coded signals. The power spectrum has no discrete components and its envelope is largely flat inside the bandwidth with a maximum at its center and a null at D.C. These characteristics make this code suited for implementation in the UWB systems based on PPM-type modulation as it assures a continuous spectrum and keeps PPM modulation performances.

Treatment and processing of residues of fermentation; Behandlung und Verwertung von Gaerrueckstaenden

Energy Technology Data Exchange (ETDEWEB)

Doehler, H.; Schliebner, P. [Kuratorium fuer Technik und Bauwesen in der Landwirtschaft (KTBL), Darmstadt (Germany)

2007-07-01

With the transformation of the EEG (Renewable Energy Resources Act), the number of biogas plants increased rapidly. Additionally, an enlargement of the performance of the plants and a regional concentration process take place. Recently, processing routes for liquid manure will be considered in order to reduce problems of the surplus of nutrients as well as the costs of the transport of the water-rich residues of fermentation. Under this aspect, the authors of the contribution under consideration report on procedures for the processing of residues of fermentation as well as costs and utilization of these procedures. By the example of an agrarian society, four procedures for the output and processing of residues of fermentation are compared with one another regarding to expenditure of work time, investments and economy: Output of residues of fermentation, treatment of residues of fermentation by separation, processing of residues of fermentation by means of diaphragm technology, processing of residues of fermentation by means of evaporation technology. The processing routes reduce the residues of fermentation by 60 %. Thus, the costs of output and the necessary storage capacities for residues of fermentation are reduced. Presently, no savings regarding to work completion by the processing of the residues of fermentation can be obtained. The specific total costs of the investigated procedures are between 2.64 Euro/m{sup 3} according to the procedure with separation and to 8.64 Euro/m{sup 3} according to the diaphragm processing route. An enhanced demand of investment does not cause compellingly the highest specific total costs of the procedures. In comparison to the output of residues of fermentation, the examined procedures for the processing of residues of fermentation do not result in economical and ergonomic advantages. The high costs of investment and operating cost of the processing of residues of fermentation cannot be compensated by the reduced costs of output

A Sub-ppm Acetone Gas Sensor for Diabetes Detection Using 10 nm Thick Ultrathin InN FETs

Science.gov (United States)

Kao, Kun-Wei; Hsu, Ming-Che; Chang, Yuh-Hwa; Gwo, Shangjr; Yeh, J. Andrew

2012-01-01

An indium nitride (InN) gas sensor of 10 nm in thickness has achieved detection limit of 0.4 ppm acetone. The sensor has a size of 1 mm by 2.5 mm, while its sensing area is 0.25 mm by 2 mm. Detection of such a low acetone concentration in exhaled breath could enable early diagnosis of diabetes for portable physiological applications. The ultrathin InN epilayer extensively enhances sensing sensitivity due to its strong electron accumulation on roughly 5–10 nm deep layers from the surface. Platinum as catalyst can increase output current signals by 2.5-fold (94 vs. 37.5 μA) as well as reduce response time by 8.4-fold (150 vs. 1,260 s) in comparison with bare InN. More, the effect of 3% oxygen consumption due to breath inhalation and exhalation on 2.4 ppm acetone gas detection was investigated, indicating that such an acetone concentration can be analyzed in air. PMID:22969342

Chlorinated pesticide residues in marine sediments

Digital Repository Service at National Institute of Oceanography (India)

Sarkar, A.; SenGupta, R.

of pesticide in contaminated river water into the Bay of Bengal. Con centration ranges of all these pesticide residues detected were, aldrine: 0.02-0.53, gamma BHC: 0.01-0.21, dieldrine: 0.05-0.51, and total DDT: 0.02-0.78, all in mu g g sup(-1) (wet wt)....

Calcination/dissolution residue treatment

International Nuclear Information System (INIS)

Knight, R.C.; Creed, R.F.; Patello, G.K.; Hollenberg, G.W.; Buehler, M.F.; O'Rourke, S.M.; Visnapuu, A.; McLaughlin, D.F.

1994-09-01

Currently, high-level wastes are stored underground in steel-lined tanks at the Hanford site. Current plans call for the chemical pretreatment of these wastes before their immobilization in stable glass waste forms. One candidate pretreatment approach, calcination/dissolution, performs an alkaline fusion of the waste and creates a high-level/low-level partition based on the aqueous solubilities of the components of the product calcine. Literature and laboratory studies were conducted with the goal of finding a residue treatment technology that would decrease the quantity of high-level waste glass required following calcination/dissolution waste processing. Four elements, Fe, Ni, Bi, and U, postulated to be present in the high-level residue fraction were identified as being key to the quantity of high-level glass formed. Laboratory tests of the candidate technologies with simulant high-level residues showed reductive roasting followed by carbonyl volatilization to be successful in removing Fe, Ni, and Bi. Subsequent bench-scale tests on residues from calcination/dissolution processing of genuine Hanford Site tank waste showed Fe was separated with radioelement decontamination factors of 70 to 1,000 times with respect to total alpha activity. Thermodynamic analyses of the calcination of five typical Hanford Site tank waste compositions also were performed. The analyses showed sodium hydroxide to be the sole molten component in the waste calcine and emphasized the requirement for waste blending if fluid calcines are to be achieved. Other calcine phases identified in the thermodynamic analysis indicate the significant thermal reconstitution accomplished in calcination

77 FR 25954 - Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2012-05-02

...; sheep, fat at 0.01 ppm; sheep, kidney at 0.3 ppm; sheep, liver at 0.7 ppm; goat, meat at 0.02 ppm; goat, meat byproducts at 0.02 ppm; goat, fat at 0.01 ppm; goat, kidney at 0.3 ppm; goat, liver at 0.7 ppm... ppm; cattle, meat at 0.2 ppm; cattle, meat byproducts at 0.2 ppm; cattle, fat at 0.01 ppm; cattle...

Demonstration of GTS Duratek Process for Stabilizing Mercury Contaminated (<260 ppm) Mixed Wastes. Mixed Waste Focus Area. OST Reference No. 2409

International Nuclear Information System (INIS)

1999-01-01

Mercury-contaminated wastes in many forms are present at various U. S. Department of Energy (DOE) sites. At least 26 different DOE sites have this type of mixed low-level waste in their storage facilities, totaling approximately 6,000 m 3 . Mercury contamination in the wastes at DOE sites presents a challenge because it exists in various forms, such as soil, sludges, and debris, as well as in different chemical species of mercury. Stabilization is of interest for radioactively contaminated mercury waste (<260 ppm Hg) because of its success with particular wastes, such as soils, and its promise of applicability to a broad range of wastes. However, stabilization methods must be proven to be adequate to meet treatment standards. They must also be proven feasible in terms of economics, operability, and safety. This report summarizes the findings from a stabilization technology demonstration conducted by GTS Duratek, Inc. Phase I of the study involved receipt and repackaging of the material, followed by preparations for waste tracking. Phase II examined the bench-scale performance of grouting at two different loadings of waste to grouted mass. Phase III demonstrated in-drum mixing and solidification using repackaged drums of sludge. Phase IV initially intended to ship final residues to Envirocare for disposal. The key results of the demonstration are as follows: (1) Solidification tests were performed at low and high waste loading, resulting in stabilization of mercury to meet the Universal Treatment Standard of 0.025 mg/L at the low loading and for two of the three runs at the high loading. The third high-loading run had a Toxicity Characteristic Leaching Procedure (TCLP) of 0.0314 mg/L. (2) Full-drum stabilization using the low loading formula was demonstrated. (3) Organic compound levels were discovered to be higher than originally reported, including the presence of some pesticides. Levels of some radionuclides were much higher than initially reported. (4

Laser Calorimetry Spectroscopy for ppm-level Dissolved Gas Detection and Analysis.

Science.gov (United States)

K S, Nagapriya; Sinha, Shashank; R, Prashanth; Poonacha, Samhitha; Chaudhry, Gunaranjan; Bhattacharya, Anandaroop; Choudhury, Niloy; Mahalik, Saroj; Maity, Sandip

2017-02-20

In this paper we report a newly developed technique - laser calorimetry spectroscopy (LCS), which is a combination of laser absorption spectroscopy and calorimetry - for the detection of gases dissolved in liquids. The technique involves determination of concentration of a dissolved gas by irradiating the liquid with light of a wavelength where the gas absorbs, and measuring the temperature change caused by the absorbance. Conventionally, detection of dissolved gases with sufficient sensitivity and specificity was done by first extracting the gases from the liquid and then analyzing the gases using techniques such as gas chromatography. Using LCS, we have been able to detect ppm levels of dissolved gases without extracting them from the liquid. In this paper, we show the detection of dissolved acetylene in transformer oil in the mid infrared (MIR) wavelength (3021 nm) region.

Incidence and Residual Risk of HIV, HBV and HCV Infections Among Blood Donors in Tehran.

Science.gov (United States)

Saber, Hamid Reza; Tabatabaee, Seyed Morteza; Abasian, Ali; Jamali, Mostafa; SalekMoghadam, Ebadollah; Hajibeigi, Bashir; Alavian, Seyed Moayed; Mirrezaie, Seyed Mohammad

2017-09-01

Estimation of residual risk is essential to monitor and improve blood safety. Our epidemiologic knowledge in the Iranian donor population regarding transfusion transmitted viral infections (TTIs), is confined to a few studies based on prevalence rate. There are no reports on residual risk of TTIs in Iran. In present survey, a software database of donor records of Tehran Blood Transfusion Center (TBTC) was used to estimate the incidence and residual risk of hepatitis B virus (HBV), hepatitis C virus (HCV) and human immunodeficiency virus (HIV) infections, by applying the incidence rate/window period (IR-WP) model. A total of 1,207,155 repeat donations was included in the analysis and represented a mean of 8.4 donations per donor over 6 years. The incidence amongst repeat donors was estimated by dividing the number of confirmed seroconverting donors by the total number of person-years at risk. The residual risk was calculated using the incidence/window period model. Incidence rate and residual risk for HBV, HCV and HIV infections were calculated for total (2005-2010) and two consecutive periods (2005-2007 and 2008-2010) of the study. According to the IR-WP model, overall residual risk for HIV and HCV in the total study period was 0.4 and 12.5 per million units, respectively and for HBV 4.57/100,000 donations. The incidence and residual risk of TTIs, calculated on TBTC's blood supply was low and comparable with developed countries for HIV infection but high for HCV and HBV infections. Blood safety may therefore be better managed by applying other techniques like nucleic acid amplification tests.

Experimental determination of the phase relationships in Zr/2.5 8.0 at% Nb/0 6.7 at% Al alloys with 750 at ppm 0 and 250 at ppm N between 730 900° C

Science.gov (United States)

Peruzzi, A.; Bolcich, J.

1990-11-01

Zr alloys with 2.5 to 8.0 at% Nb and 0 to 6.7 at% Al were subjected to dynamic and static treatments between 730-900° C and studied by qualitative and quantitative optical metallography, electrical resistance, X-ray diffractometry and electron microanalysis. The experimental data were analyzed by taking into account the effects of oxygen and nitrogen impurities. The main results for Zn-Nb-Al alloys with 750 at ppm O and 250 at ppm N are the following: (i) Equilibrium relationships are established between the α (hcp), β (bcc) and Zr 3Al (Cu 3Au) phases along isothermal sections at 730, 771 and 800°C. (ii) The β/ α + β boundaries are determined along iso-aluminum vertical sections at 6.7, 3.3 and 0 at% Al. (iii) The addition of Al to Zr-Nb alloys increases the solubility of Nb in the α phase, its maximum value at 730° C being about 0.7-0.8 at% for 4 at% Al. (iv) Solubility values for Al in the α-phase of Zr-Al were estimated by extrapolation from ternary alloys. These estimates help to solve an existing discrepancy in the Zr-Al system.

Residual stress effects in LMFBR fracture assessment procedures

International Nuclear Information System (INIS)

Hooton, D.G.

1984-01-01

Two post-yield fracture mechanics methods, which have been developed into fully detailed failure assessment procedures for ferritic structures, have been reviewed from the point of view of the manner in which as-welded residual stress effects are incorporated, and comparisons then made with finite element and theoretical models of centre-cracked plates containing residual/thermal stresses in the form of crack-driving force curves. Applying the procedures to austenitic structures, comparisons are made in terms of failure assessment curves and it is recommended that the preferred method for the prediction of critical crack sizes in LMFBR austenitic structures containing as-welded residual stresses is the CEGB-R6 procedure based on a flow stress defined at 3% strain in the parent plate. When the prediction of failure loads in such structures is required, it is suggested that the CEGB-R6 procedure be used with residual/thermal stresses factored to give a maximum total stress of flow stress magnitude

Effect of sulfite treatment on total antioxidant capacity, total oxidant status, lipid hydroperoxide, and total free sulfydryl groups contents in normal and sulfite oxidase-deficient rat plasma.

Science.gov (United States)

Herken, Emine Nur; Kocamaz, Erdogan; Erel, Ozcan; Celik, Hakim; Kucukatay, Vural

2009-08-01

Sulfites, which are commonly used as preservatives, are continuously formed in the body during the metabolism of sulfur-containing amino acids. Sulfite oxidase (SOX) is an essential enzyme in the pathway of the oxidative degradation of sulfite to sulfate protecting cells from sulfite toxicity. This article investigated the effect of sulfite on total antioxidant capacity (TAC), total oxidant status, lipid hydroperoxide (LOOH), and total free sulfydryl groups (-SH) levels in normal and SOX-deficient male albino rat plasma. For this purpose, rats were divided into four groups: control, sulfite-treated, SOX-deficient, and sulfite-treated SOX-deficient groups. SOX deficiency was established by feeding rats a low molybdenum diet and adding to their drinking water 200 ppm tungsten. Sulfite (70 mg/kg) was administered to the animals via their drinking water. SOX deficiency together with sulfite treatment caused a significant increase in the plasma LOOH and total oxidant status levels. -SH content of rat plasma significantly decreased by both sulfite treatment and SOX deficiency compared to the control. There was also a significant decrease in plasma TAC level by sulfite treatment. In conclusion, sulfite treatment affects the antioxidant/oxidant balance of the plasma cells of the rats toward oxidants in SOX-deficient groups.

78 FR 11126 - Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2013-02-15

...; barley, hay at 0.01 ppm; barley, straw at 0.01 ppm; cattle, fat at 0.01 ppm; cattle, meat at 0.01 ppm; cattle, meat byproducts at 0.01 ppm; goat, fat at 0.01 ppm; goat, meat at 0.01 ppm; goat, meat byproducts at 0.01 ppm; horse, fat at 0.01 ppm; horse, meat at 0.01 ppm; horse, meat byproducts at 0.01 ppm...

75 FR 864 - Notice of Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or...

Science.gov (United States)

2010-01-06

....10 ppm; cattle; meat at 0.10 ppm; cattle; meat byproducts; except liver at 0.10 ppm; cattle; liver at 1.2 ppm; eggs at 0.1 ppm; goat; fat at 0.10 ppm; goat; meat at 0.10 ppm; goat; meat byproducts; except liver at 0.10 ppm; goat; liver at 1.2 ppm; hog; fat at 0.01 ppm; hog; meat at 0.01 ppm; hog; meat...

75 FR 46924 - Notice of Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or...

Science.gov (United States)

2010-08-04

... seed at 12 ppm; cattle, fat at 0.05 ppm; cattle, meat at 0.05 ppm; cattle, meat byproducts at 0.05 ppm; goat, fat at 0.05 ppm; goat, meat at 0.05 ppm; goat, meat byproducts at 0.05 ppm; horse, fat at 0.05 ppm; horse, meat at 0.05 ppm; horse, meat byproducts at 0.05 ppm; sheep, fat at 0.05 ppm; sheep, meat...

Development and evaluation of analytical techniques for total chlorine in burner fuels

International Nuclear Information System (INIS)

Gaskill, A. Jr.; Estes, E.D.; Hardison, D.L.; Friedman, P.H.

1987-01-01

A current EPA regulation prohibits the sale for burning in non-industrial boilers of used oils and oil fuels contaminated above specified levels with certain metals and total chlorine. When burned as fuel in a small boiler, the contaminants may be emitted to the ambient air at hazardous levels. This regulation establishes a rebuttable presumption that used oil containing more than 1,000 ppm total chlorine has been mixed with halogenated solvents and is a hazardous waste. Rebutting the presumption requires the seller of the oil to prove that this chlorine is not due to halogenated solvents or other hazardous halogenated organics. If the rebuttal is successful, the oil can be sold as fuel up to a level of 4000 ppm total chlorine. Analytical techniques for determination of total chlorine were evaluated or developed to provide regulatory agencies and the regulated community with appropriate chlorine test methods. The techniques evaluated included chemical titrations following oxygen bomb combustion, disposable field test kits, instrumental microcoulometry, and x-ray fluorescence spectrometry. These candidate techniques were subjected to interlaboratory testing to estimate their precision, accuracy, sensitivity, and susceptibility to matrix effects. Information on ease of use and analysis costs was also collected. Based on this pilot study, test methods will be written for the most promising techniques and subjected to a formal collaborative study to generate precision and accuracy data for each method. These methods are to be proposed in the Federal Register as mandatory for compliance with the existing used oil regulation

Mapping and quantification of organic agro-industrial residues in East Africa

Energy Technology Data Exchange (ETDEWEB)

Jungersen, G. [Dansk Teknologisk Inst. (Denmark); Kivaisi, A.; Rubindamayugi, M. [Univ. of Dar es Salaam (Tanzania, United Republic of)

1998-05-01

The East-African agro-industries generate very large quantities of organic residues from production and processing of different crops. These residues form a major contribution to the pollution of air, soil and water ways, but, at the same time they constitute a large potential for production of bioenergy through anaerobic digestion as well as potential substrate for other biological fermentation processes. The utilization of these resources for production of valuable products would contribute significantly to: Improvement of the local energy supply, through production of bio-energy; Improvement of the economy of the East African agro-industry; Reduction of the environmental impact from the agro-industrial sector. Except for production of cane sugar, most agro-industrial residues are generated from cash crops, which are produced and processed in the developing countries and where the final products mainly are used for export. In the East-African Region the most important of these crops are: Sisal, coffee, Cashew nuts and Pineapple. In addition significant quantities of organic residues are generated from other food processing activities like breweries, consumption of bananas etc. The total potential methane production of the residues available for use in biomethanization systems in East Africa is 189.61 million m{sup 3} of methane per year. Converted to diesel oil equivalents and including the residues only feasible for combustion systems, the total bioenergy potential of agro-industrial residues in Eastern Africa is 279,176 TOE. If this potential was fully utilized for production of electricity, it would correspond to installed effects of 37,68 and 31 MW in Tanzania, Kenya and Uganda, respectively, equivalent to 10%, 11% and 18% of the currently installed effect is these countries. Residues from sisal and coffee processing constitute the main part of the bioenergy potential, on average approximately 75%, while the remaining 25% of the potential are formed by the

EFEKTIVITAS KAPORIT PADA PROSES KLORINASI TERHADAP PENURUNAN BAKTERI Coliform DARI LIMBAH CAIR RUMAH SAKIT X SAMARINDA (The Effectiveness of Calcium Hypochlorite to Chlorination Process in Decreasing the Amount of Coliform Bacteria in the Wastewater of X

Directory of Open Access Journals (Sweden)

Muhammad Busyairi

2016-07-01

Full Text Available ABSTRAK Kaporit pada limbah cair rumah sakit digunakan sebagai desinfektan, tetapi, penggunaan kaporit dengan dosis yang tidak tepat akan menyebabkan pembentukan senyawa Trihalomethane (THMs yang beracun dan bersifat karsinogenik. Pada limbah cair rumah sakit X Samarinda, diperoleh nilai MPN Coliform sebesar >160.000 MPN / 100 mL dengan residu klor sebesar 0 ppm. Penelitian ini bertujuan untuk menentukan dosis optimum dari penggunaan kaporit menggunakan titik Breakpoint Chlorination (BPC dan pengaruhnya terhadap penurunan Coliform. Analisis dilakukan dengan titrasi iodometri dan menghitung jumlah bakteri Coliform memakai metode Most Probable Number (MPN. Penentuan dosis kaporit berdasarkan dosis optimum pada titik BPC dimaksudkan agar dapat menjaga residu klor dari penambahan dosis yang semakin meningkat. Hasil penelitian mempengarui rerata kadar bahan organik pada sampel limbah cair sebesar 137,26 ppm, sehingga dosis kaporit yang dibubuhkan dimulai dari 130-165 ppm. Titik BPC terjadi pada pembubuhan klor aktif 160 ppm untuk kedua waktu kontak yaitu 30 dan 40 menit. Pada titik BPC, waktu kontak 30 menit diperoleh rerata persentase penurunan nilai Coliform yaitu 98,21% sebesar 2.899 MPN / 100 mL dengan residu klor sebesar 88 ppm. Pada waktu kontak 40 menit diperoleh persentase penurunan bakteri Coliform hingga 98,83%, yaitu dari >160.000/100 mL menjadi 1.866/100 mL dengan residu klor 97,5 ppm. ABSTRACT Calcium hypochlorite of hospital wastewater serves as disinfectant, however, inappropriate dose of it will lead to the formation of Trihalomethane (THMs which is toxic and carcinogenic. The value of MPN Coliform of wastewater in X hospital Samarinda is >160.000 MPN / 100 mL with residual chlorine 0 ppm. This research aims at determining the optimum dose of calcium hypochlorite usage by using Breakpoint Chlorination curve and its effect to Coliform decrease. Further, the analysis is done by employing iodometric titration and the amount of Coliform

Red/Green Currant and Sea Buckthorn Berry Press Residues as Potential Sources of Antioxidants for Food Use.

Science.gov (United States)

Puganen, Anna; Kallio, Heikki P; Schaich, Karen M; Suomela, Jukka-Pekka; Yang, Baoru

2018-04-04

The potential for using extracts of press residues from black, green, red, and white currants and from sea buckthorn berries as sources of antioxidants for foods use was investigated. Press residues were extracted with ethanol in four consecutive extractions, and total Folin-Ciocalteu (F-C) reactive material and authentic phenolic compounds were determined. Radical quenching capability and mechanisms were determined from total peroxyl radical-trapping antioxidant capacity (TRAP) and oxygen radical absorbance capacity (ORAC) assays and from diphenylpicrylhydrazyl (DPPH) kinetics, respectively; specific activities were normalized to F-C reactive concentrations. Levels of total F-C reactive materials in press residue extracts were higher than in many fruits and showed significant radical quenching activity. Black currant had the highest authentic phenol content and ORAC, TRAP, and DPPH reactivity. Sea buckthorn grown in northern Finland showed extremely high total specific DPPH reactivity. These results suggest that berry press residues offer attractive value-added products that can provide antioxidants for use in stabilizing and fortifying foods.

Study on the relation between uranium content and total phosphorus in some sudanese phosphate ore samples

International Nuclear Information System (INIS)

Mohammed, A.A.; Eltayeb, M.A.H.

2003-01-01

In the present work uranium content and total phosphorous were determined in 30 phosphate ore samples collected from Kurun and Uro areas in Nuba mountains in sudan. Spectrophotometry technique was used for this purpose. Uranium analysis is based on the use of nitrogen (V) acid for leaching the rock, and treatment with ammonium carbonate solution, whereby uranium (VI) is kept in solution as its carbonate complex. The ion-exchange technique was used for the recovery of uranium. Uranium was eluted from the resin with 1 M hydrochloric acid. In the elute, uranium was determined spectrophotometrically by measurement of the absorbance of the yellow uranium (VI) - 8- hydroxyquinolate complex at λ 400 nm. The total phosphorus was measured as (P 2 O 5 %) by treatment of the leach liquor with ammonium molybdate solution. The absorbance of the blue complex was measured at λ 880 nm. The results show that a limited relation is existed between uranium content and total phosphorus in phosphate samples from Kurun area, which contain 58.8 ppm uranium in average, where there are no relation is existed in phosphate samples samples from Uro area, which contain 200 ppm uranium in average

Distribution, utilization structure and potential of biomass resources in rural China: With special references of crop residues

Energy Technology Data Exchange (ETDEWEB)

Liu, H [Laboratory of Quantitative Vegetation Ecology, Institute of Botany, Chinese Academy of Sciences, 20 Nanxincun, Xiangshan, Beijing 100093 (China); Graduate University of Chinese Academy of Sciences, Beijing 100049 (China); Jiang, G M [Laboratory of Quantitative Vegetation Ecology, Institute of Botany, Chinese Academy of Sciences, 20 Nanxincun, Xiangshan, Beijing 100093 (China); Agronomy Department, Shandong Agricultural University, Tai' an 271018, Shandong Province (China); Zhuang, H Y [National Bio-Energy CO., LTD, No. 26B, Financial Street, Xicheng District, Beijing 100032 (China); Shandong Academy of Sciences, No. 19, Keyuan Road, Ji' nan 250014, Shandong Province (China); Wang, K J [Agronomy Department, Shandong Agricultural University, Tai' an 271018, Shandong Province (China)

2008-06-15

As the largest developing country in the world, China is urgently in short of energy and natural resources. However, biological resources such as crop residues are burnt in the field, which cause serious environmental pollution. Still it is not clear how much storage and potential of these huge crop residues are in China. This paper firstly reported the distribution, utilization structure and potential of crop biomass and provided the tangible information of crop residues in rural China through careful collecting and recalculating data. From 1995 to 2005, China produces some 630 million tons of crop residues per year, 50% of which comes from east and central south of China. The amount of crop residues is 1.3 times of the total yield of crops, 2 times of the total fodder of grassland, which covers 41% of China's territory. Crop residues of corn, wheat and rice amounted to 239, 137 and 116 million tons, respectively, accounting for nearly 80% of the total crop residues. Unfortunately, the utilizing structure is seriously improper for such abundant biomass resources. Although 23% of the crop residues are used for forage, 4% for industry materials and 0.5% for biogas, the large parts are used with lower efficiency or wasted, with 37% being directly combusted by farmers, 15% lost during collection and the rest 20.5% discarded or directly burnt in the field. Reasonable adjustment of the utilizing pattern and popularization of the recycling agriculture are essential out-ways for residues, with the development of the forage industry being the breakthrough point. We suggested that utilizing the abandoned 20.5% of the total residues for forage and combining agriculture and stock raising can greatly improve the farm system and cut down fertilizer pollution. Through the development of forage industries, the use efficiency of crop residues could be largely enhanced. Commercializing and popularizing technologies of biomass gasification and liquefaction might be substitute

78 FR 33785 - Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2013-06-05

..., pads at 0.9 ppm; cattle/goat/hog/horse/sheep, fat at 0.5 ppm; cattle/goat/hog/horse/sheep, meat at 1 ppm; cattle/goat/hog/horse/ sheep, meat byproducts at 2 ppm; milk at 0.3 ppm; poultry, eggs at 0.3 ppm..., liver at 0.01 ppm; goat, meat at 0.01 ppm; goat, meat byproducts at 0.01 ppm; hog, fat at 0.01 ppm; hog...

Crystallization and preliminary X-ray analysis of the stress-response PPM phosphatase RsbX from Bacillus subtilis

International Nuclear Information System (INIS)

Suganuma, Masatoshi; Teh, Aik Hong; Makino, Masatomo; Shimizu, Nobutaka; Kaneko, Tomonori; Hirata, Kunio; Yamamoto, Masaki; Kumasaka, Takashi

2009-01-01

The bacterial PPM phosphatase RsbX from B. subtilis was expressed in E. coli, purified and crystallized. The crystal belonged to space group P1 and diffracted to 1.06 Å resolution. RsbX from Bacillus subtilis is a manganese-dependent PPM phosphatase and negatively regulates the signal transduction of the general stress response by the dephosphorylation of RsbS and RsbR, which are activators of the alternative RNA polymerase σ factor SigB. In order to elucidate the structural–functional relationship of its Ser/Thr protein-phosphorylation mechanism, an X-ray crystallographic diffraction study of RsbX was performed. Recombinant RsbX was expressed in Escherichia coli, purified and crystallized. Crystals were obtained using the sitting-drop vapour-diffusion method and X-ray diffraction data were collected to 1.06 Å resolution with an R merge of 8.1%. The crystals belonged to the triclinic space group P1, with unit-cell parameters a = 33.3, b = 41.7, c = 68.6 Å, α = 98.8, β = 90.0, γ = 108.4°

Residual stresses

International Nuclear Information System (INIS)

Sahotra, I.M.

2006-01-01

The principal effect of unloading a material strained into the plastic range is to create a permanent set (plastic deformation), which if restricted somehow, gives rise to a system of self-balancing within the same member or reaction balanced by other members of the structure., known as residual stresses. These stresses stay there as locked-in stresses, in the body or a part of it in the absence of any external loading. Residual stresses are induced during hot-rolling and welding differential cooling, cold-forming and extruding: cold straightening and spot heating, fabrication and forced fitting of components constraining the structure to a particular geometry. The areas which cool more quickly develop residual compressive stresses, while the slower cooling areas develop residual tensile stresses, and a self-balancing or reaction balanced system of residual stresses is formed. The phenomenon of residual stresses is the most challenging in its application in surface modification techniques determining endurance mechanism against fracture and fatigue failures. This paper discusses the mechanism of residual stresses, that how the residual stresses are fanned and what their behavior is under the action of external forces. Such as in the case of a circular bar under limit torque, rectangular beam under limt moment, reclaiming of shafts welds and peening etc. (author)

Prevention of Post-Radiotherapy Failure in Prostate Cancer by Vitamin D

Science.gov (United States)

2007-05-01

reported As reported Residual solvents Ethyl acetate DMSO Methanol Dichloromethane GC 5,000 ppm 5,000 ppm 3,000 ppm 600 ppm...Heavy metals Aluminum Selenium Zinc ICP-MS NMT 50 ppm NMT 20 ppm NMT 75 ppm DMSO = dimethylsulfoxide ; GC = gas chromatography...indicate any obvious safety concerns. The solvents DMSO and methanol slightly exceeded specification requirements but given that the International

A comparative clinical study investigating the efficacy of a test dentifrice containing 8% strontium acetate and 1040 ppm sodium fluoride versus a marketed control dentifrice containing 8% arginine, calcium carbonate, and 1450 ppm sodium monofluorophosphate in reducing dentinal hypersensitivity.

Science.gov (United States)

Hughes, Nathan; Mason, Stephen; Jeffery, Peter; Welton, Helen; Tobin, Maira; O'Shea, Caoimhe; Browne, Mairead

2010-01-01

The objective of this clinical study was to evaluate and compare the efficacy in reducing dentin hypersensitivity of an 8% strontium acetate, 1040 ppm sodium fluoride dentifrice to a marketed control 8% arginine, calcium carbonate, 1450 ppm sodium monofluorophosphate dentifrice after twice-daily brushing for two, four, and eight weeks. This was a randomized, examiner-blind, two-arm parallel group, eight-week longitudinal clinical study with seventy-nine subjects, stratified based on baseline tooth sensitivity (Schiff score, Yeaple). Subjects brushed with either an 8% strontium acetate-based dentifrice or a marketed 8% arginine calcium carbonate dentifrice twice daily for approximately one minute. At screening, baseline, weeks two, four, and eight, subjects' tooth sensitivity was determined through both evaporative (Schiff and Visual Analogue Scale [VAS]) and tactile stimuli (Yeaple probe). Subject assessments using each stimulus were performed by the same examiner throughout the study. Seventy-seven subjects completed this clinical study. Both subject groups exhibited significant cumulative reductions from baseline to Days 14, 28, and 56 in dentin hypersensitivity as measured by Schiff, Yeaple, and VAS (for the 8% strontium acetate group, p carbonate group, p = 0.0031 for Yeaple at Day 14, p = 0.0015 for VAS at Day 14, and p 0.05) were observed between treatments for any of the time points and measures except for tactile sensitivity at Day 56, for which the 8% strontium acetate-based dentifrice was statistically superior (p = 0.0391) to the control 8% arginine calcium carbonate dentifrice. The 8% strontium acetate, 1040 ppm sodium fluoride dentifrice provided significant reductions in dentin hypersensitivity (p carbonate dentifrice showed no significant differences (p > 0.05) apart from tactile (Yeaple) sensitivity at week 8, where the 8% strontium acetate-based dentifrice showed significant improvement over the control (p = 0.0391).

Highest PBDE levels (max 63 ppm) yet found in biota measured in seabird eggs from San Francisco Bay

Energy Technology Data Exchange (ETDEWEB)

She, J.; Holden, A.; Tanner, M.; Sharp, M.; Hooper, K. [Department of Toxic Substances Control, Berkeley, CA (United States). Hazardous Materials Lab.; Adelsbach, T. [Environmental Contaminants Division, Sacramento Fish and Wildlife Office, US Fish and Wildlife Service, Sacramento, CA (United States)

2004-09-15

High levels of polybrominated diphenylethers (PBDEs) have been found in humans and wildlife from the San Francisco Bay Area, with levels in women among the highest in the world, and levels in piscivorous seabird eggs at the ppm level. Seabirds are useful for monitoring and assessing ecosystem health at various times and places because they occupy a high trophic level in the marine food web, are long-lived, and are generally localized near their breeding and non-breeding sites. In collaboration with the US Fish and Wildlife Services (USFWS), we are carrying out a three-year investigation of dioxin, PCB and PBDE levels in eggs from fish-eating seabirds. Year 1 (2002) PBDE measurements from 73 bird eggs were reported at Dioxin2003. Year 2 (2003) PBDE measurements from 45 samples are presented in this report. The highest PBDE level measured in eggs was 63 ppm, lipid, which is the highest PBDE level, yet reported in biota.

Release behavior of triazine residues in stabilised contaminated soils

International Nuclear Information System (INIS)

Ying, G.G.; Kookana, R.S.; Mallavarpu, M.

2005-01-01

This paper reports the release behavior of two triazines (atrazine and simazine) in stabilised soils from a pesticide-contaminated site in South Australia. The soils were contaminated with a range of pesticides, especially with triazine herbicides. With multiple extractions of each soil sample with deionised water (eight in total), 15% of atrazine and 4% of simazine residues were recovered, resulting in very high concentrations of the two herbicides in leachate. The presence of small fractions of surfactants was found to further enhance the release of the residues. Methanol content up to 10% did not substantially influence the concentration of simazine and atrazine released. The study demonstrated that while the stabilisation of contaminated soil with particulate activated carbon (5%) and cement mix (15%) was effective in locking the residues of some pesticides, it failed to immobilise triazine herbicides residues completely. Given the higher water solubility of these herbicides than other compounds more effective strategies to immobilise their residues is needed. - Stabilisation of contaminated soil with a mix of activated carbon and cement may fail to immobilise some contaminants like triazines

Endosulfan residues in fish from the MUDA rice agroecosystem

International Nuclear Information System (INIS)

Nashriyah Mat; Sabri Junoh; Nuriati Nurdin

2002-01-01

A study was carried out in the recycled and the non-recycled areas of the Muda rice agroecosystem to determine the residue level of endosulfan in rice field fish. Snakehead or haruan (Channa striata), climbing perch or puyu (Anabas testudineus), walking catfish or keli (Clariasspp.) and snakeskin gouramy or sepat siam (Trichogasterpectoralis) were sampled and the tissues analysed using Gas Liquid Chromatography. Endosulfan sulphate metabolite was a ubiquitous residue in all fish at levels ranging from 0.0065 μg/g to 0.9837 μg/g of tissue wet weight whilst α-isomer was detected at a much lower concentration followed by β-isomer. In Channa striata, endosulfan total residue (α+β+sulphate) was accumulated in fish tissues sampled at ACRBD4 (non-recycled) site followed by Blok 14 (recycled) site. Endosulfan residue concentration did not coincide with water recycling practice nor changes in EROD enzyme activity. (Author)

Acid transformation of bauxite residue: Conversion of its alkaline characteristics.

Science.gov (United States)

Kong, Xiangfeng; Li, Meng; Xue, Shengguo; Hartley, William; Chen, Chengrong; Wu, Chuan; Li, Xiaofei; Li, Yiwei

2017-02-15

Bauxite residue (BR) is a highly alkaline solid hazardous waste produced from bauxite processing for alumina production. Alkaline transformation appears to reduce the environmental risk of bauxite residue disposal areas (BRDAs) whilst potentially providing opportunities for the sustainable reuse and on-going management of BR. Mineral acids, a novel citric acid and a hybrid combination of acid-gypsum treatments were investigated for their potential to reduce residue pH and total alkalinity and transform the alkaline mineral phase. XRD results revealed that with the exception of andradite, the primary alkaline solid phases of cancrinite, grossular and calcite were transformed into discriminative products based on the transformation used. Supernatants separated from BR and transformed bauxite residue (TBR) displayed distinct changes in soluble Na, Ca and Al, and a reduction in pH and total alkalinity. SEM images suggest that mineral acid transformations promote macro-aggregate formation, and the positive promotion of citric acid, confirming the removal or reduction in soluble and exchangeable Na. NEXAFS analysis of Na K-edge revealed that the chemical speciation of Na in TBRs was consistent with BR. Three acid treatments and gypsum combination had no effect on Na speciation, which affects the distribution of Na revealed by sodium STXM imaging. Copyright © 2016 Elsevier B.V. All rights reserved.

A randomized clinical trial of the anti-caries efficacy of 5,000 compared to 1,450 ppm fluoridated toothpaste on root caries lesions in elderly disabled nursing home residents

DEFF Research Database (Denmark)

Ekstrand, K.R.; Poulsen, J.E.; Hede, B.

2013-01-01

Root caries is prevalent in elderly disabled nursing home residents in Denmark. This study aimed to compare the effectiveness of tooth brushing with 5,000 versus 1,450 ppm of fluoridated toothpaste (F-toothpaste) for controlling root caries in nursing home residents. The duration of the study was 8...... months. Elderly disabled residents (n = 176) in 6 nursing homes in the Copenhagen area consented to take part in the study. They were randomly assigned to use one of the two toothpastes. Both groups had their teeth brushed twice a day by the nursing staff. A total of 125 residents completed the study...

Effect of the interaction between diet composition and the PPM1K genetic variant on insulin resistance and β cell function markers during weight loss: results from the Nutrient Gene Interactions in Human Obesity: implications for dietary guidelines (NUGENOB) randomized trial

DEFF Research Database (Denmark)

Goni, Leticia; Qi, Lu; Cuervo, Marta

2017-01-01

Background: Circulating branched-chain amino acids (BCAAs) and aromatic amino acids (AAAs) have been shown to be associated with insulin resistance and diabetes risk. The common rs1440581 T allele in the protein phosphatase Mg2+/Mn2+ dependent 1K (PPM1K) gene has been related to elevated BCAA...... concentrations and risk of type 2 diabetes.Objective: In the present study, we tested whether dietary fat and carbohydrate intakes influenced the association between the rs1440581 PPM1K genetic variant and glucose-metabolism traits during weight loss.Design: The rs1440581 PPM1K genetic variant was genotyped...... in a total of 757 nondiabetic individuals who were randomly assigned to 1 of 2 energy-restricted diets that differed in macronutrient composition (low-fat diet: 20-25% fat, 15% protein, and 60-65% carbohydrate; high-fat diet: 40-45% fat, 15% protein, and 40-45% carbohydrate). The changes in fasting glucose...

Determination of total arsenic in streams and sediments from Obuasi gold mines

International Nuclear Information System (INIS)

Serfor Armah, Yaw

1994-03-01

In this work streams and sediments of Obuasi, a major gold mining town in Ghana were analysed. In addition to the total arsenic the parameters determined included the levels of Pe, Al, Nn and Au and nutrients. Leaching of arsenic from the sediment was also carried out to ascertain the rate at which As will be removed from the sediment to acceptable levels. Results indicate that in spite of the newly installed Arsenic Recovery Plant (ARP) which is able to remove about 90% of the arsenic dusts, the streams in the area remain heavily polluted with arsenic. In the water Total Arsenic values range between 0.13 - 20.00ppm. The sediments are also polluted to a depth of at least 30cm with values ranging from 15.38 - 50.00ppm. Contrary to expectations, the gold concentration in both the water and sediment are too low and may not be suitable for exploration. The leaching results show that very little amount of arsenic was leached from the sediments. Even after 20 weeks of continuous leaching less than 1% of As had been leached. This was attributed to the ability of arsenic to form sparingly soluble compounds with Fe, Al, Mn etc in the sediment environment. (au)

Residual stresses

International Nuclear Information System (INIS)

Macherauch, E.

1978-01-01

Residual stresses are stresses which exist in a material without the influence of external powers and moments. They come into existence when the volume of a material constantly changes its form as a consequence of mechanical, thermal, and/or chemical processes and is hindered by neighbouring volumes. Bodies with residual stress are in mechanical balance. These residual stresses can be manifested by means of all mechanical interventions disturbing this balance. Acoustical, optical, radiological, and magnetical methods involving material changes caused by residual stress can also serve for determining residual stress. Residual stresses have an ambivalent character. In technical practice, they are feared and liked at the same time. They cause trouble because they can be the cause for unexpected behaviour of construction elements. They are feared since they can cause failure, in the worst case with catastrophical consequences. They are appreciated, on the other hand, because, in many cases, they can contribute to improvements of the material behaviour under certain circumstances. But they are especially liked for their giving convenient and (this is most important) mostly uncontrollable explanations. For only in very few cases we have enough knowledge and possibilities for the objective evaluation of residual stresses. (orig.) [de

Residual subsidence analysis after the end of coal mine work. Example from Lorraine Colliery, France

International Nuclear Information System (INIS)

Al Heib, M.; Nicolas, M.; Noirel, J.F.; Wojtkowiak, F.

2005-01-01

This paper describes the residual movements associated with the deep coal mines. The studied case relates to works located into Lorraine coal basin. The paper is divided into two sections. The first one describes subsidence phenomena, especially the residual phase in terms of amplitude, duration and localization. The second one focus on Morsbach case: the total and residual subsidence measurements will be analyzed and compared to the state of the art as well as the currant knowledge. The results of the analysis show that the duration of residual movements does not exceed 24 months and their amplitude is about 5% of total subsidence. We analyze also the declarations of the mining damage during and after the mining period. Damages occur, after this period are probably due to late observations. (authors)

75 FR 19393 - Notice of Withdrawal of Pesticide Petitions for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2010-04-14

... ppm; ginseng at 0.3 ppm; mushroom at 0.09 ppm; nut, tree, group 14 at 0.2 ppm; sunflower at 0.05 ppm; vegetable, tuberous and corm, subgroup 1C at 0.1 ppm; tomato and tomatillo at 1.4 ppm; and mustard (grown...

Evaluation of Crops Sensitivity to Atrazine Soil Residual

Directory of Open Access Journals (Sweden)

E Izadi

2012-02-01

Full Text Available Abstract In order to study the sensitivity of 9 crops to atrazine soil residual, two separate experiments were conducted in field and greenhouse conditions. First experiment was conducted in a field with treated soil by atrazine based on split plot and the results evaluated in greenhouse conditions. Treatments in the field experiment included two organic manure application rates (0 and 50 t/ha as main plots and 2 atrazine application rates (2 and 4 kg/ha atrazine a.i. as sob plots. After corn harvesting soil was sampled at 0-15 cm surface layer in each plots in 15 points, after mixing the samples. Wheat, barley, sugar beet, pea, lens and colza planted in pots at greenhouse. Second experiment conducted in greenhouse conditions for evaluation of atrazine soil residual in completely randomized design. Treatments included atrazine soil residual concentrations (0, 0.2, 0.5, 1, 5, 10 and 15 mg/kg soil and crops included wheat, barley, sugar beet, pea, lens, rape, bean and tomato. Results showed that atrazine residue had no effect on crops growth in field experiment treated with atrazine. It seems that atrazine residue in filed soil is lower that its damage threshold for crops or maybe for its fast removal in field than in control conditions. But in bioassay experiment (greenhouse experiment crops response to atrazine residues were different. Results showed that onion and pea were most susceptible ant tolerant crops between studied species and based of ED50 parameter the other crops tolerance to total residue ranked as: pea< bean< lentil< sugar beet< tomato< barley< wheat< rape< onion. Keywords: Atrazine residue, Pea, Bean, Lentil, Sugar beet, Barley, Wheat, Rape, Tomato

77 FR 66781 - Notice of Filing of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or...

Science.gov (United States)

2012-11-07

..., fresh leaves at 1.5 ppm; dill oil at 4.8 ppm; dill seed at 0.3 ppm; horseradish at 0.050 ppm; parsley, dried leaves at 8.3 ppm; parsley leaves at 3 ppm; and pea, dry, seed at 0.08 ppm. Adequate enforcement... on parsley, leaves at 0.25 ppm upon approval of the tolerances listed under ``New Tolerance'' for PP...

In vivo Prompt Gamma Neutron Activation Analysis Facility for Total Body Nitrogen and Cd

International Nuclear Information System (INIS)

Munive, Marco; Revilla, Angel; Solis, Jose L.

2007-01-01

A Prompt Gamma Neutron Activation Analysis (PGNAA) system has been designed and constructed to measure the total body nitrogen and Cd for in vivo studies. An aqueous solution of KNO 3 was used as phantom for system calibration. The facility has been used to monitor total body nitrogen (TBN) of mice and found that is related to their diet. Some mice swallowed diluted water with Cl 2 Cd, and the presence of Cd was detected in the animals. The minimum Cd concentration that the system can detect was 20 ppm

Evaluation of residue-residue contact predictions in CASP9

KAUST Repository

Monastyrskyy, Bohdan

2011-01-01

This work presents the results of the assessment of the intramolecular residue-residue contact predictions submitted to CASP9. The methodology for the assessment does not differ from that used in previous CASPs, with two basic evaluation measures being the precision in recognizing contacts and the difference between the distribution of distances in the subset of predicted contact pairs versus all pairs of residues in the structure. The emphasis is placed on the prediction of long-range contacts (i.e., contacts between residues separated by at least 24 residues along sequence) in target proteins that cannot be easily modeled by homology. Although there is considerable activity in the field, the current analysis reports no discernable progress since CASP8.

Experimental ethylene oxide neuropathy. Chronic exposure to 250 ppm in rats

Energy Technology Data Exchange (ETDEWEB)

Ohnishi, A.; Yamamoto, T.; Inoue, N.; Tanaka, I.; Koga, M.

1985-12-01

In Wistar rats subjected to a six-hour exposure to ethylene oxide (ETO) at the concentration of 250 parts per million once a day, five times a week for 9 months, histopathologic studies of myelinated fibers of the proximal sural, distal sural and peroneal nerves and of the fasciculus gracilis at the fifth thoracic and third cervical segments of the spinal cord were performed to reveal whether ETO of such concentration produces the degeneration of the primary sensory neuron. Throughout the study, no definite abnormality of the gait or posture was observed in both control and test rats. Qualitative histologic studies disclosed preferential distal axonal degeneration of myelinated fibers in both sural nerves and gracile fascicles in test rats, although the extent of the distribution and the severity of the degenerative findings were variable among test rats. Therefore, it was concluded that exposure to 250 ppm ethylene oxide produces central-peripheral distal axonal degeneration of the primary sensory neuron in rats.

In situ chemical composition measurement of individual cloud residue particles at a mountain site, southern China

Directory of Open Access Journals (Sweden)

Q. Lin

2017-07-01

Full Text Available To investigate how atmospheric aerosol particles interact with chemical composition of cloud droplets, a ground-based counterflow virtual impactor (GCVI coupled with a real-time single-particle aerosol mass spectrometer (SPAMS was used to assess the chemical composition and mixing state of individual cloud residue particles in the Nanling Mountains (1690 m a. s. l. , southern China, in January 2016. The cloud residues were classified into nine particle types: aged elemental carbon (EC, potassium-rich (K-rich, amine, dust, Pb, Fe, organic carbon (OC, sodium-rich (Na-rich and Other. The largest fraction of the total cloud residues was the aged EC type (49.3 %, followed by the K-rich type (33.9 %. Abundant aged EC cloud residues that mixed internally with inorganic salts were found in air masses from northerly polluted areas. The number fraction (NF of the K-rich cloud residues increased within southwesterly air masses from fire activities in Southeast Asia. When air masses changed from northerly polluted areas to southwesterly ocean and livestock areas, the amine particles increased from 0.2 to 15.1 % of the total cloud residues. The dust, Fe, Pb, Na-rich and OC particle types had a low contribution (0.5–4.1 % to the total cloud residues. Higher fraction of nitrate (88–89 % was found in the dust and Na-rich cloud residues relative to sulfate (41–42 % and ammonium (15–23 %. Higher intensity of nitrate was found in the cloud residues relative to the ambient particles. Compared with nonactivated particles, nitrate intensity decreased in all cloud residues except for dust type. To our knowledge, this study is the first report on in situ observation of the chemical composition and mixing state of individual cloud residue particles in China.

SnO2 quantum dots with rapid butane detection at lower ppm-level

Science.gov (United States)

Cai, Pan; Dong, Chengjun; Jiang, Ming; Shen, Yuanyuan; Tao, You; Wang, Yude

2018-04-01

SnO2 quantum dots (QDs) were successfully synthesized by a facile approach employing benzyl alcohol and ammonium hydroxide at lower temperature of 130 °C. It is revealed that the SnO2 QDs is about 3 nm in size to form clusters. The gas sensor based on SnO2 QDs shows a high potential for detecting low-ppm-level butane at 400 °C, exhibiting a high sensitivity, short response and rapid recovery time, and effective selectivity. The sensing mechanism is understood in terms of adsorbed oxygen species. Significantly, the excellent sensing performance is attributed to the smaller size of SnO2 and larger surface area (204.85 m2/g).

Analysis of the Performance of a PAM/PPM/OOK System Operating with OCDMA, under Nonlinear Optical Effects in Optical Fiber Propagation

Science.gov (United States)

Correia, D. G.; Sales, J. C.; Pinto, P. V. F.; Moura, L. P.; Ferreira, A. C.; Menezes, J. W. M.; Guimarães, G. F.; Sombra, A. S. B.

2016-06-01

In this article, we present a numerical simulation study of encoding, decoding and propagation performance of short optical pulses and words with modulations OOK, PAM and PPM in OCDMA systems (Optical Code Division Multiple Access). The encoding and decoding of short pulses are obtained through fiber Bragg grating(FBG - FBG optical) devices, where the codes are inserted through discrete jumps in the optical phase (±π) where Gold codes were used. A figure of merit (SNR - Signal to Noise Ratio) was obtained to quantify the interference in propagation of short optical pulses. An increase in the temporal width was observed. For decoded pulses due to the nonlinearity effect, we observed an increase of 1.3 ps considering the propagation with γ=3 W-1 km-1 and γ=24 W-1 km-1. Analysis of coding and decoding words "a" and "w" was done. Considering the propagation (with γ=9 W-1 km-1) of a word "w", an error occurred in all modulations except for simultaneous PPM/PAM modulation, which is associated to the better autocorrelation characteristics obtained with the OOK, PAM and PPM modulations alone, and could double the transmission rate. The nonlinear effects directly affect the process of the autocorrelation codes due to interference from adjacent chip components of the code.

Soil and crop residue CO2-C emission under tillage systems in sugarcane-producing areas of southern Brazil

Directory of Open Access Journals (Sweden)

Luís Gustavo Teixeira

2013-10-01

Full Text Available Appropriate management of agricultural crop residues could result in increases on soil organic carbon (SOC and help to mitigate gas effect. To distinguish the contributions of SOC and sugarcane (Saccharum spp. residues to the short-term CO2-C loss, we studied the influence of several tillage systems: heavy offset disk harrow (HO, chisel plow (CP, rotary tiller (RT, and sugarcane mill tiller (SM in 2008, and CP, RT, SM, moldboard (MP, and subsoiler (SUB in 2009, with and without sugarcane residues relative to no-till (NT in the sugarcane producing region of Brazil. Soil CO2-C emissions were measured daily for two weeks after tillage using portable soil respiration systems. Daily CO2-C emissions declined after tillage regardless of tillage system. In 2008, total CO2-C from SOC and/or residue decomposition was greater for RT and lowest for CP. In 2009, emission was greatest for MP and CP with residues, and smallest for NT. SOC and residue contributed 47 % and 41 %, respectively, to total CO2-C emissions. Regarding the estimated emissions from sugarcane residue and SOC decomposition within the measurement period, CO2-C factor was similar to sugarcane residue and soil organic carbon decomposition, depending on the tillage system applied. Our approach may define new emission factors that are associated to tillage operations on bare or sugarcane-residue-covered soils to estimate the total carbon loss.

75 FR 32463 - Notice of Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or...

Science.gov (United States)

2010-06-08

... commodities poultry, fat at 0.1 ppm; poultry, meat byproducts at 0.1 ppm; poultry, meat at 0.1 ppm; and eggs... at 0.7 ppm; goat, fat at 0.8 ppm; goat, kidney at 0.4 ppm; goat, liver at 0.4 ppm; goat, muscle at 0...

The relative contribution of waves, tides, and nontidal residuals to extreme total water levels on U.S. West Coast sandy beaches

Science.gov (United States)

Serafin, Katherine A.; Ruggiero, Peter; Stockdon, Hilary F.

2017-01-01

To better understand how individual processes combine to cause flooding and erosion events, we investigate the relative contribution of tides, waves, and nontidal residuals to extreme total water levels (TWLs) at the shoreline of U.S. West Coast sandy beaches. Extreme TWLs, defined as the observed annual maximum event and the simulated 100 year return level event, peak in Washington, and are on average larger in Washington and Oregon than in California. The relative contribution of wave-induced and still water levels (SWL) to the 100 year TWL event is similar to that of the annual maximum event; however, the contribution of storm surge to the SWL doubles across events. Understanding the regional variability of TWLs will lead to a better understanding of how sea level rise, changes in storminess, and possible changes in the frequency of major El Niños may impact future coastal flooding and erosion along the U.S. West Coast and elsewhere.

Fungal leaching of valuable metals from a power plant residual ash using Penicillium simplicissimum: Evaluation of thermal pretreatment and different bioleaching methods.

Science.gov (United States)

Rasoulnia, P; Mousavi, S M; Rastegar, S O; Azargoshasb, H

2016-06-01

Each year a tremendous volume of V-Ni rich ashes is produced by fuel oil consuming power plants throughout the world. Recovery of precious metals existing in these ashes is very important from both economic and environmental aspects. The present research was aimed at investigating bioleaching potential of Penicillium simplicissimum for the recovery of metals from power plant residual ash (PPR ash) using different bioleaching methods such as one-step, two-step, and spent-medium bioleaching at 1% (w/v) pulp density. Furthermore, the effects of thermal pretreatment on leaching of V, Ni, and Fe, as major elements present in PPR ash, were studied. Thermal pretreatment at various temperatures removed the carbonaceous and volatile fraction of the ash and affected the fungal growth and metal leachability. The highest extraction yields of V and Ni were achieved for the original PPR ash, using spent-medium bioleaching in which nearly 100% of V and 40% of Ni were extracted. The maximum extraction yield of Fe (48.3%) was obtained for the pretreated PPR ash at 400°C by spent-medium bioleaching. In addition, the fungal growth in pure culture was investigated through measurement of produced organic acids via high performance liquid chromatography (HPLC). Chemical leaching experiments were performed, using commercial organic acids at the same concentrations as those produced under optimum condition of fungal growth (5237ppm citric, 3666ppm gluconic, 1287ppm oxalic and 188ppm malic acid). It was found that in comparison to chemical leaching, bioleaching improved V and Ni recovery up to 19% and 12%, respectively. Moreover, changes in physical and chemical properties as well as morphology of the samples utilizing appropriate analytical methods such as XRF, XRD, FTIR, and FE-SEM were comprehensively investigated. Copyright © 2016 Elsevier Ltd. All rights reserved.

Plant and soil pollution caused by lead residues of petrol engines

Energy Technology Data Exchange (ETDEWEB)

Horak, V O; Huber, I

1974-01-01

The lead content of plants near a major, well-traveled road were measured. Vegetative aboveground parts of plants contained-depending on the distance from the road-3-220 ppm lead/dry matter. Remnants of dried plants contained up to 539 ppm of lead in early spring. Lead content of plants depended on the sampling date, intensity of growth, and morphology of the material. The lead content decreases with the distance from the roads. In soils, amounts of 12-30 ppm of lead were found far from the road and 27-290 ppm of lead were detected near the road. (in german) (3 graphs, 26 references, 8 tables )

Persistence of malathion residues in stored wheat

International Nuclear Information System (INIS)

Farghaly, M.; Zayed, S.M.A.D.

1990-01-01

The persistence of succinate- 14 C-malathion in stored wheat was investigated under local conditions during a storage period of 32 weeks. The insecticide penetrated readily into the seed and up to 16% of the applied dose was found to be bound after 32 weeks in storage. Total terminal residues declined to 9.3 and 21.0 mg/kg from initially applied doses of 12.2 and 24.4 mg/kg respectively. A small percentage of malaoxon was detected only during the early weeks after treatment (3-5%). Malathion was the major constituent of the extractable residues. In addition, seven degradation products were detected and identified. (author). 6 refs, 2 figs, 2 tabs

The potential for energy production from crop residues in Zimbabwe

Energy Technology Data Exchange (ETDEWEB)

Jingura, R.M.; Matengaifa, R. [School of Engineering Sciences and Technology, Chinhoyi University of Technology, P. Bag 7724, Chinhoyi (Zimbabwe)

2008-12-15

There is increasing interest in Zimbabwe in the use of renewable energy sources as a means of meeting the country's energy requirements. Biomass provides 47% of the gross energy consumption in Zimbabwe. Energy can be derived from various forms of biomass using various available conversion technologies. Crop residues constitute a large part of the biomass available from the country's agriculture-based economy. The potential for energy production of crop residues is examined using data such as estimates of the quantities of the residues and their energy content. The major crops considered are maize, sugarcane, cotton, soyabeans, groundnuts, wheat, sorghum, fruits and forestry plantations. Quantities of residues are estimated from crop yields by using conversion coefficients for the various crops. Long-term crop yields data from 1970 to 1999 were used. Total annual residue yields for crops, fruits and forestry plantations are 7.805 Mt, 378 kt and 3.05 Mt, respectively. The crops, fruits and forestry residues have energy potential of 81.5, 4.9 and 44.3 PJ per year, respectively. This represents about 44% of the gross energy consumption in Zimbabwe. The need to balance use of crop residues for both energy purposes and other purposes such as animal feeding and soil fertility improvement is also highlighted. (author)

Residual stress measurement in 304 stainless steel weld overlay pipes

International Nuclear Information System (INIS)

Yen, H.J.; Lin, M.C.C.; Chen, L.J.

1996-01-01

Welding overlay repair (WOR) is commonly employed to rebuild piping systems suffering from intergranular stress corrosion cracking (IGSCC). To understand the effects of this repair, it is necessary to investigate the distribution of residual stresses in the welding pipe. The overlay welding technique must induce compressive residual stress at the inner surface of the welded pipe to prevent IGSCC. To understand the bulk residual stress distribution, the stress profile as a function of location within wall is examined. In this study the full destructive residual stress measurement technique -- a cutting and sectioning method -- is used to determine the residual stress distribution. The sample is type 304 stainless steel weld overlay pipe with an outside diameter of 267 mm. A pipe segment is cut from the circular pipe; then a thin layer is removed axially from the inner to the outer surfaces until further sectioning is impractical. The total residual stress is calculated by adding the stress relieved by cutting the section away to the stress relieved by axially sectioning. The axial and hoop residual stresses are compressive at the inner surface of the weld overlay pipe. Compressive stress exists not only at the surface but is also distributed over most of the pipe's cross section. On the one hand, the maximum compressive hoop residual stress appears at the pipe's inner surface. The thermal-mechanical induced crack closure from significant compressive residual stress is discussed. This crack closure can thus prevent IGSCC very effectively

Characterization of protein and carbohydrate mid-IR spectral features in crop residues

Science.gov (United States)

Xin, Hangshu; Zhang, Yonggen; Wang, Mingjun; Li, Zhongyu; Wang, Zhibo; Yu, Peiqiang

2014-08-01

To the best of our knowledge, a few studies have been conducted on inherent structure spectral traits related to biopolymers of crop residues. The objective of this study was to characterize protein and carbohydrate structure spectral features of three field crop residues (rice straw, wheat straw and millet straw) in comparison with two crop vines (peanut vine and pea vine) by using Fourier transform infrared spectroscopy (FTIR) technique with attenuated total reflectance (ATR). Also, multivariate analyses were performed on spectral data sets within the regions mainly related to protein and carbohydrate in this study. The results showed that spectral differences existed in mid-IR peak intensities that are mainly related to protein and carbohydrate among these crop residue samples. With regard to protein spectral profile, peanut vine showed the greatest mid-IR band intensities that are related to protein amide and protein secondary structures, followed by pea vine and the rest three field crop straws. The crop vines had 48-134% higher spectral band intensity than the grain straws in spectral features associated with protein. Similar trends were also found in the bands that are mainly related to structural carbohydrates (such as cellulosic compounds). However, the field crop residues had higher peak intensity in total carbohydrates region than the crop vines. Furthermore, spectral ratios varied among the residue samples, indicating that these five crop residues had different internal structural conformation. However, multivariate spectral analyses showed that structural similarities still exhibited among crop residues in the regions associated with protein biopolymers and carbohydrate. Further study is needed to find out whether there is any relationship between spectroscopic information and nutrition supply in various kinds of crop residue when fed to animals.

Baseline toxicity of a chlorobenzene mixture and total body residues measured and estimated with solid-phase microextraction

NARCIS (Netherlands)

Leslie, H.A.; Hermens, J.L.; Kraak, M.H.S.

2004-01-01

Body residues of compounds with a narcotic mode of action that exceed critical levels result in baseline toxicity in organisms. Previous studies have shown that internal concentrations in organisms also can be estimated by way of passive sampling. In this experiment, solid-phase microextraction

Radionuclides in Bayer process residues: previous analysis for radiological protection

International Nuclear Information System (INIS)

Cuccia, Valeria; Rocha, Zildete; Oliveira, Arno H. de

2011-01-01

Natural occurring radionuclides are present in many natural resources. Human activities may enhance concentrations of radionuclides and/or enhance potential of exposure to naturally occurring radioactive material (NORM). The industrial residues containing radionuclides have been receiving a considerable global attention, because of the large amounts of NORM containing wastes and the potential long term risks of long-lived radionuclides. Included in this global concern, this work focuses on the characterization of radioactivity in the main residues of Bayer process for alumina production: red mud and sand samples. Usually, the residues of Bayer process are named red mud, in their totality. However, in the industry where the samples were collected, there is an additional residues separation: sand and red mud. The analytical techniques used were gamma spectrometry (HPGe detector) and neutron activation analysis. The concentrations of radionuclides are higher in the red mud than in the sand. These solid residues present activities concentrations enhanced, when compared to bauxite. Further uses for the residues as building material must be more evaluated from the radiological point of view, due to its potential of radiological exposure enhancement, specially caused by radon emission. (author)

Decomposition of sugar cane crop residues under different nitrogen rates

Directory of Open Access Journals (Sweden)

Douglas Costa Potrich

2014-09-01

Full Text Available The deposition of organic residues through mechanical harvesting of cane sugar is a growing practice in sugarcane production system. The maintenance of these residues on the soil surface depends mainly on environmental conditions. Nitrogen fertilization on dry residues tend to retard decomposition of these, providing benefits such as increased SOM. Thus, the object of this research was to evaluate the effect of different doses of nitrogen on sugar cane crop residues, as its decomposition and contribution to carbon sequestration in soil. The experiment was conducted in Dourados-MS and consisted of a randomized complete block design. Dried residues were placed in litter bags and the treatments were arranged in a split plot, being the four nitrogen rates (0, 50, 100 and 150 kg ha-1 N the plots, and the seven sampling times (0, 30, 60, 90, 120, 150 and 180 the spit plots. Decomposition rates of residues, total organic carbon and labile carbon on soil were analysed. The application of increasing N doses resulted in an increase in their decomposition rates. Despite this, note also the mineral N application as a strategy to get higher levels of labile carbon in soil.

Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings.

Science.gov (United States)

Larsen, Julie D; Nielsen, Steen M; Scheutz, Charlotte

2017-11-01

Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during the resting period. As the resting period proceeded, atmospheric air re-entered the pore space at all depth levels. The methane (CH 4 ) concentration was at its highest during the first part of the resting period, and then declined as the sludge residue became more dewatered and thereby aerated. In the pore space, the concentration of CH 4 often exceeded the concentration of carbon dioxide (CO 2 ). However, the total emission of CO 2 from the surface of the sludge residue exceeded the total emission of CH 4 , suggesting that CO 2 was mainly produced in the layer of newly applied sludge and/or that CO 2 was emitted from the sludge residue more readily compared to CH 4 .

75 FR 35801 - Notice of Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or...

Science.gov (United States)

2010-06-23

... ppm; goat, meat at 0.01 ppm; goat, meat byproducts at 0.10 ppm; hog, fat at 0.01 ppm; hog, liver at 0... ppm; canola seed at 0.05 ppm; meat and meat byproducts except liver of cattle, goat, hog, horse, and... stoichiometric equivalent of pyrasulfotole, in or on cattle, goat, hog, sheep, horse, meat at 0.04 ppm; cattle...

Efecto residual de dos rocas fosfóricas puras y parcialmente aciduladas, comparadas con SFT, sobre la aprovechabilidad del P por Panicum maximum L., en un oxisol de los Llanos Orientales de Colombia

Directory of Open Access Journals (Sweden)

Alejo M. Doris

1986-03-01

Full Text Available Panicum maximum L. se sembró, en condiciones de invernadero, en un Oxisol de los Llanos Orientales de Colombia, 18 meses después de la aplicación de las fuentes (rocas fosfóricas de Pesca - Colombia y Sechura - Perú crudas y aciduladas al 20 % con H3 P04, en dosis de 25, 50 Y 100 ppm de P. La roca fosfórica Sechura cruda y parcialmente acidulada junto con SFT, tuvieron el mejor efecto residual sobre el rendimiento y captación de P y mantuvieron los más altos niveles de P asimilable en el suelo al final del ensayo. Con las dosis superiores se obtuvo un nivel más alto de P asimilable en el suelo y mayor absorción de P por la planta.In order to study the residual effect of the Pesca (Colombia and Sechura (Perú phosphate rocks, both crude and acidulated in 20 % by H3P04, comparatively with SFT, Panicum rnaximum L. was planted under glasshouse conditions, in an Oxisol from the Eastern plains of Colombia, 18 months after sources application, with rates of 25. 50 and 100 ppm of P. Crude and partially acidulated Sechura phosphate rock, together with TSP, had the best residual effect on yield and P absorption and had the highest available P levels in the soil at the end of the trial. The highest available P level in the soil and P uptake by the plant was obtained with higher P rates.

The effect of gamma irradiation on in vitro digestible energy of some agricultural residues

International Nuclear Information System (INIS)

Al-Masri, M.R.

1993-03-01

Experiments have been carried out on the effect of gamma irradiation on total energy, dry organic matter digestibility and on digestible energy of organic matter for some agricultural residues (maize straw, lentils straw, cottonwood, residues of apple-tree pruning, olive-cake first and second treatment). Sample were irradiated at 0, 50 and 100 KGy. Total energy was estimated by calorimeter. Digestibility was estimated in vitro by the method of Tilly and Terry (1963). Two sheep with rumen fistula were used as rumen liquor donating animals. Irradiation resulted in increasing the digestion of organic and dry matter and also the digestible energy of organic matter in all residues used except lentils straw and olive-cake first treatment. The increase in digestible energy values of organic matter (kJ) at dose of 100 KGy were: 155, 105, 71 and 25 for residue of apple-tree pruning, maize straw, cottonwood and olive-cake second treatment, respectively. (author).28 refs., 10 figs., 5 tabs

A radiochemical NAA method for the determination of tin, barium, copper and antimony- role of tin as an indicator for gun shot residues

International Nuclear Information System (INIS)

Chattopadhyay, N.; Basu, A.K.; Tripathi, A.B.R.; Rao, M.S.; Anil Kumar, S.; Parthasarathy, R.; Mathur, P.K.

1998-01-01

Metallic tin being present as impurity and hardening agent of lead bullet/shot, is expected to play an important role in forensic ballistics in matching of bullet lead specimens for establishment of commonness of origin and also as an additional parameter for characterisation of Gun Shot Residue (GSR). 121 Sn is a suitable radioisotope for quantification of the element at ppm level if it is separated in highest radiochemical purity. A sequential Radiochemical Neutron Activation Analysis (RNAA) procedure for its simultaneous determination along with trace levels of Ba, Cu and Sb has been developed and its applications in forensic science are described. (author)

ANALISIS RESIDU KLORPIRIFOS DALAM SAYUR-SAYURAN DENGAN TEKNIK HIGH PERFORMANCE LIQUID CHROMATOGRAPHY (HPLC

Directory of Open Access Journals (Sweden)

Aman Sentosa Panggabean

2016-06-01

Full Text Available The research about analysis of chlorpyrifos residue in vegetables by using High Performance Liquid Chromatography (HPLC technique has been done. To obtain the optimal measurement results, the measurement performed several important parameters in the chromatographic system was composition of mobile phase, volume injection sample, flow rate and pH eluent. Optimum measurement conditions obtained was mobile phase composition (water : methanol with 70 : 30, volume injection sample are 5 mL, flow rate are 0.5mL/menit and pH eluent are 7. The analytical performance that obtained is good showed with the reproducibility value as percentage coefficient variance (% CV was 0.0664%, limit of detection (LOD was 0.44 ppm, with a recovery percentage of > 95%. The results obtained showed the HPLC technique can be used for the routine analysis in the determination of chlorpyrifos for the vegetable samples. Keywords: Chlorpyrifos, Vegetables, HPLC.

Irradiation of residual muds and its use in the oat cultivation

International Nuclear Information System (INIS)

Moreno, A.J.; Colin, C.A.; Gomeztagle, M.M.; Frias, P.H.

1997-01-01

The irradiation of residual muds samples from a wastewater treatment plant at gamma radiation dose of 15 kGy removes from muds on average: fats and oils (33%), detergent (92%), phenols (50%) and over 99% of microorganisms of total account. The evaluation of irradiated residual mud and without irradiation as soil conditioner in oat growing (avena safira), was realized by triplicate, using different rates (80, 60, 40 and 20%) of frank sandy soil and irradiated and non-irradiated residual mud. The growing with rates 60/40 % of soil and irradiated mud respectively, resulted being more adequate as soil conditioner. It is important to clarify that for putting residual mud it is necessary that metals concentration not exceed the maximum permissible levels for the soil type and the corresponding growing. (Author)

Optimal Path Choice in Railway Passenger Travel Network Based on Residual Train Capacity

Directory of Open Access Journals (Sweden)

Fei Dou

2014-01-01

Full Text Available Passenger’s optimal path choice is one of the prominent research topics in the field of railway passenger transport organization. More and more different train types are available, increasing path choices from departure to destination for travelers are unstoppable. However, travelers cannot avoid being confused when they hope to choose a perfect travel plan based on various travel time and cost constraints before departure. In this study, railway passenger travel network is constructed based on train timetable. Both the generalized cost function we developed and the residual train capacity are considered to be the foundation of path searching procedure. The railway passenger travel network topology is analyzed based on residual train capacity. Considering the total travel time, the total travel cost, and the total number of passengers, we propose an optimal path searching algorithm based on residual train capacity in railway passenger travel network. Finally, the rationale of the railway passenger travel network and the optimal path generation algorithm are verified positively by case study.

Fusion evaporation-residue cross sections for 28Si+40Ca at E(28Si)=309, 397, and 452 MeV

International Nuclear Information System (INIS)

Vineyard, M.F.; Bauer, J.S.; Crum, J.F.; Gosdin, C.H.; Trotter, R.S.; Kovar, D.G.; Beck, C.; Henderson, D.J.; Janssens, R.V.F.; Wilkins, B.D.; Maguire, C.F.; Mateja, J.F.; Prosser, F.W.; Stephans, G.S.F.

1992-01-01

Velocity distributions of mass-identified evaporation residues produced in the 28 Si+ 40 Ca reaction have been measured at bombarding energies of 309, 397, and 452 MeV using time-of-flight techniques. These distributions were used to identify evaporation residues and to separate the complete-fusion and incomplete-fusion components. Angular distributions and upper limits for the total evaporation-residue and complete-fusion evaporation-residue cross sections were extracted at all three bombarding energies. The complete-fusion evaporation-residue cross sections and the deduced critical angular momenta are compared with earlier measurements and the predictions of existing models. The ratios of the complete-fusion evaporation-residue cross section to the total evaporation-residue cross section, along with those measured for the 28 Si+ 12 C and 28 Si+ 28 Si systems at the same energies, support the entrance-channel mass-asymmetry dependence of the incomplete-fusion evaporation-residue process reported earlier

Survey of Veterinary Drug Residues in Raw Milk in Hebei Province, China.

Science.gov (United States)

Han, Rong-Wei; Yu, Zhong-Na; Zhen, Tian-Yuan; Wang, Jun

2017-10-17

The objective of this study was to investigate the occurrence of veterinary drug residues in raw milk from Hebei, the second-largest dairy production province in the People's Republic of China. A total of 192 raw milk samples were collected from 64 milk stations in seven districts. Twenty-eight veterinary drug residues were analyzed by ultraperformance liquid chromatography with tandem mass spectrometry based on a China National Standard. Raw milk samples with multiple residues of veterinary drugs were not found in the present study. Residues of four veterinary drugs, penicillin G, sulfacetamide, trimethoprim, and lincomycin, were detected in 12 (6.25%) raw milk samples, with detection ratios of 1.04, 0.52, 3.13, and 1.56%, respectively. All veterinary drug residues detected were under the maximum residue levels as regulated by China, the European Union, the United States, and the Codex Alimentarius Commission. In general, raw milk from Hebei province was considered relatively safe for human consumption because of the low prevalence of veterinary drug residues. However, stringent control measurements for veterinary drug residues in raw milk are required because some veterinary drugs were detected in milk from some areas of Hebei province.

A risk assessment for crude oil in residential surface soils

International Nuclear Information System (INIS)

Sullivan, M.J.; Miller, C.J.; Custance, S.R.

1991-01-01

This paper reports that the discovery of crude oil residues in residential soils is occurring with increasing frequency as property previously owned by the petroleum industry is sold and developed for housing. Many states have adopted action levels for total petroleum hydrocarbons (TPH) in soil for the purpose of discerning those sites requiring remediation and/or monitoring. Many states are known to have action levels consisting of a single concentration value which may carry from 10 to 100 ppm TPH. Other states incorporate a range of action levels for addressing site-specific needs; values range from 10 to 1000 ppm TPH for gasoline in soils

Influence of organic waste and residue mud additions on chemical, physical and microbial properties of bauxite residue sand.

Science.gov (United States)

Jones, Benjamin E H; Haynes, Richard J; Phillips, Ian R

2011-02-01

wet sieving, was greatest where poultry manure was applied. Although total organic C and soluble organic C were greater in biosolids than poultry manure treatments, the reverse was the case for microbial biomass C and basal respiration. In the biosolids and poultry manure treatments, increasing residue mud additions tended to increase soluble C, microbial biomass C and basal respiration. Germination index of watercress was highest in control samples and reduced by additions of biosolids and poultry manure which was attributed to the high EC and possibly high extractable P and NH (4) (+) . The concurrent addition of residue mud and organic wastes can improve chemical, microbial and particularly physical properties of residue sand. Future research should include neutralisation of the mud (e.g. with gypsum) and subsequent leaching to remove salts originating from both the mud and organic wastes.

Recovering recyclable materials from shredder residue

Science.gov (United States)

Jody, Bassam J.; Daniels, Edward J.; Bonsignore, Patrick V.; Brockmeier, Norman F.

1994-02-01

Each year, about 11 million tons of metals are recovered in the United States from about 10 million discarded automobiles. The recovered metals account for about 75 percent of the total weight of the discarded vehicles. The balance of the material, known as shredder residue, amounts to about three million tons annually and is currently landfilled. The residue contains a diversity of potentially recyclable materials, including polyurethane foams, iron oxides, and certain thermoplastics. This article discusses a process under development at Argonne National Laboratory to separate and recover the recyclable materials from this waste stream. The process consists essentially of two stages. First, a physical separation is used to recover the foams and the metal oxides, followed by a chemical process to extract certain thermoplastics. The status of the technology and the process economics are reviewed here.

Determination of total mercury and methylmercury in human head hair by radiochemical methods of analysis

International Nuclear Information System (INIS)

Vasconcellos, M.B.A.; Saiki, M.; Paletti, G.; Baruzzi, R.G.; Rodrigues, D.A.; Cuten, J.

1995-01-01

Total mercury has been determined by instrumental neutron activation analysis in the hair of several Indian tribes living in the Xingu Park, located in the Amazonic region of Brazil. Methylmercury and total mercury have been determined in selected samples using cold vapour atomic absorption spectroscopy, at the Nuclear Chemistry Department, Jozef Stefan Institute, Ljubliana, Slovenia. Mercury levels were found to be much higher in the Indian hair samples as compared to the samples from the control population. The arithmetic and geometric means for total mercury in the Indian hair samples ranged from 10 to 20 ppm, compared to values of about 1 ppm for the means of the control group. The results obtained for methylmercury have shown that the majority of the mercury is present in the hair of the Indians as the organic form. The Indian study populations living in the Xingu Park can thus be considered as being at risk with regards to contamination by mercury. With the aim of applying neutron activation analysis for the determination of methylmercury in hair, experiments were done at the IEA-R1 nuclear research reactor irradiating cysteine- and also thioacetamide- impregnated filter papers, on which a methylmercury solution was pipetted. The results obtained have shown that all the mercury was lost from the cysteine-impregnated paper and about 90 % of the mercury remained on the paper impregnated with thioacetamide. (author)

Pesticide residues in food of plant origin from Southeast Asia – A Nordic project

DEFF Research Database (Denmark)

Skretteberg, L. G.; Lyrån, B.; Holen, B.

2015-01-01

Fruits and vegetables from Souteast Asia were analysed for the presence of pesticide residues. A total of 721 samples of 63 different commodities were collected in 2011. The products were imported to Denmark, Finland, Norway and Sweden from ten countries; about 80% were imported from Thailand....... The reason for the increased control for certain food products from Southeast Asia was that the official control had revealed many products with too high levels of pesticide residues. In 60% of the samples we did not find any residues, while 28% had residues below or at the MRLs. Results above the MRLs were...

Design of a process for the use of residual hydrocarbons coming from the ships arriving at Moin for obtaining of a fuel

International Nuclear Information System (INIS)

Madrigal Calderon, Adolfo

2015-01-01

A process is designed to carry out the obtaining of a fuel from the residual mixture of residual oils coming from the ships arriving at Moin, Limon, Costa Rica . A sampling of the residual oil in different ships is realized for a month to quantify the water content and basic sediment, as well as the heavy metal content. The results obtained have been 20,4 ± 4,6 % v/v of water and sediment, and 6,939 ppm of heavy metals as a minimum, this value may be higher depending on the quality of lubricant. The production volume of the residual oil is estimated according to historical data of the company ACASE S.A. (company responsible for collecting the oil residue of ships arriving at dock of Moin, Limon); therefore, the plant must process 25,000 liters of dirty oil per day. The main technologies (thermal process, treatment with chemical reaction, vacuum distillation and solvent extraction) to perform the process are compared and studied through a selection matrix. The technical and economic parameters chosen for the matrix have been: environmental impact, cost of operation, cost of equipment, safety of operation, maintenance of equipment, by-products obtained, waste generated, quality of the product obtained and ease of operation. The study has concluded that the treatment with chemical reaction has been the best option for the project of used oil utilization, as well as other physical methods of cleaning as the centrifugation of the same one. The installation of a waste oil processing plant has been a project that environmentally represents a benefit and economically viable, as currently the residual oil is left untreated for later use [es

77 FR 26477 - Receipt of a Pesticide Petition Filed for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2012-05-04

..., granules/flakes at 5.5 ppm; cattle, goat, hog, horse, sheep, fat at 1.0 ppm; cattle, goat, hog, horse, sheep, liver at 0.5 ppm; cattle, goat, hog, horse, sheep, meat at 0.2 ppm; cattle, goat, hog, horse, sheep, meat byproducts at 0.4 ppm; and milk, fat at 0.5 ppm. The High-performance Liquid Chromatograph...

CHARACTERIZATION OF AGROINDUSTRIAL RESIDUES WITH A VIEW TO ITS EXPLOITATION

Directory of Open Access Journals (Sweden)

Emir Cabrera Rodríguez

2016-10-01

Full Text Available Agroindustrial residues are considered one of the most important renewable resources to obtain products of economic and social interest. This study assesses the potential use of coconut husk, sugar cane straw and sugar cane bagasse marrow through their chemical characterization. For this, the total solid contents, the ash, lignin, holocellulose and extractive contents are determined, as well as the zero charge Ph and the total acid and basic groups of materials. Results show a large lignin percentage in coconut husk composition (42.3 ± 1.03%, which is significantly higher than that of the other residues. That is why this material is a promising feedstock to obtain high-added value chemical products like phenolic compounds, which can replace those derived from crude oil. Straw and marrow have high holocellulose percentages of 61.1 ± 1.0% and 60.3 ± 1.3%, respectively, deserving attention as feedstock for biofuels production and chemical compound synthesis. On the other hand, all residues have higher number of acid sites with a predominance of carboxyl and hydroxyl groups according to infrared spectroscopy (FTIR. Therefore, all materials display potentialities for heavy metals and dissolving colorants biosorption.

Relationship between spirituality/religiousness and coping in patients with residual schizophrenia.

Science.gov (United States)

Shah, Ruchita; Kulhara, Parmanand; Grover, Sandeep; Kumar, Suresh; Malhotra, Rama; Tyagi, Shikha

2011-09-01

To measure spirituality/religiousness and its relation to coping skills in patients with residual schizophrenia. Using a cross-sectional design, 103 persons with residual schizophrenia were assessed on Positive and Negative Syndrome Scale [PANSS] and Ways of Coping Checklist [WCC] to assess the repertoire of coping skills and WHO Quality of Life-Spirituality, Religiousness and Personal Belief scale [WHOQOL-SRPB] to assess religiousness and spirituality. Positive reappraisal as a coping strategy had significant positive correlation with all the facets of WHOQOL-SRPB and SRPB total domain scores. The coping subscales of accepting responsibility, planful problem solving, distancing, confrontive coping, and self-controlling also had significant positive correlations with different facets of WHOQOL-SRPB and total SRPB domain score. Seeking social support and escape-avoidance as coping mechanisms had no correlations with any of the WHOQOL-SRPB facets. A sound spiritual, religious, or personal belief system is associated with active and adaptive coping skills in subjects with residual schizophrenia. Understanding and assessing the spirituality and religiousness of subjects with schizophrenia can help in better management of the disorder.

The tyrosyl residues in creatine kinase. Modification by iodine.

Science.gov (United States)

Fattoum, A; Kassab, R; Pradel, L A

1975-10-20

The effect of the iodination of tyrosyl residues in creatine kinase from rabbit muscle has been investigated at alkaline pH after reversible masking of the reactive thiol groups. The conversion of 4-5 tyrosyl residues to monoiodotyrosines as measured by spectrotitration and by radioactive iodine labelling resulted in almost total loss of enzymic activity. The modified enzyme was unable to bind its nucleotide substrates but no significant conformational change was revealed by optical rotatory dispersion or Stokes radius measurements. However, change in the reactivity of some non-essential thiol groups, presumably those located near the active thiol groups, was observed.

A non-dispersive infrared analyser for analysis of HF in the PPM range

International Nuclear Information System (INIS)

Kartha, V.B.; Patel, N.D.; Venkateswaran, S.

1985-01-01

The determination of trace amounts of HF is of importance in many industrial processes, and in nuclear industry in the production of UF 6 . Mass spectrometric and gas chromatographic methods are difficult to use for this purpose, because of the highly corrosive nature of the samples. Infrared Spectroscopy can be conveniently used with the required sensitivity and it has the added advantage that continuous non-destructive on-line monitoring can be conveniently done. A non-dispersive infrared analyser for determination of HF in UF 6 in the concentration range of 50-2000 ppm has been fabricated and tested. The instrument has been shown to possess high sensitivity and good long term stability, so that it can be used as on-line monitor for non-destructive, continuous analysis. (author)

Sulfur compounds and species in Russian residues by XPS and PY-GC-PFPO

Energy Technology Data Exchange (ETDEWEB)

Quan, S.; Suoqi, Z.; Chunming, X. [University of Petroleum, State Key Laboraory of Heavy Oil Processing, Beijing (China); Kotlyar, L.; Kung, J. [National Research Council of Canada, Institute for Chemical processand Environmental Technology, Ottawa, ON (Canada); Chung, K. H. [Syncrude Canada Limited, Edmonton, AB (Canada)

2004-07-01

Distribution and structure of sulfur components of Russian crude oil were investigated by separating vacuum residues from the oil into 17 narrow cuts and one end-cut using the supercritical fluid extraction and fractionation technique (SFEF). The cuts were analyzed by gas chromatography, with conditions optimized from 600 degrees C to 1,000 degrees C, and between two and twenty seconds. In general, the total amount of of the sulfur compounds in pyrolizates was found to be proportional to the sulfur content in the vacuum residues. Thiophenes, benzothiophenes and dibenzothiophene content varied from vacuum residue to vacuum residue. Benzothiophens were identified as the dominant sulfur compounds in the pyrolizate of Russian crude oil.

Phytosterols elevation in bamboo shoot residue through laboratorial scale solid-state fermentation using isolated Aspergillus niger CTBU.

Science.gov (United States)

Zheng, X X; Chen, R S; Shen, Y; Yin, Z Y

2014-04-01

Aspergillus niger CTBU isolated from local decayed bamboo shoot residue was employed to solid-state fermentation (SSF) of bamboo shoot residue to elevate the content of phytosterols. Strain acclimatization was carried out under the fermentation condition using bamboo shoot as substrate for fermentation performance improvement. The optimal fermentation temperature and nitrogen level were investigated using acclimatized strain, and SSF was carried out in a 500-ml Erlenmeyer flask feeding 300-mg bamboo shoot residue chips under the optimal condition (33 °C and feeding 4 % urea), and 1,186 mg (100 g)(-1) of total phytosterol was attained after 5-day fermentation, in comparison, only 523 mg (100 g)(-1) of phytosterol was assayed in fresh shoots residue. HPLC analysis of the main composition of total phytosterols displays that the types of phytosterols and composition ratio of main sterols keep steady. This laboratorial scale SSF unit could be scaled up for raw phytosterols production from discarded bamboo shoot residue and could reduce its cost.

Derivation of uranium residual radioactive material guidelines for the Ventron site

International Nuclear Information System (INIS)

Loureiro, C.; Yu, C.; Jones, L.

1992-03-01

Residual radioactive material guidelines for uranium were derived for the Ventron site in Beverly, Massachusetts. This site has been identified for remedial action under the Formerly Utilized Sites Remedial Action Program of the US Department of Energy (DOE). The derivations for the single radionuclides and the total uranium guidelines were based on the requirement that the 50-year committed effective dose equivalent to a hypothetical individual who lives or works in the immediate vicinity of the Ventron site should not exceed a dose of 100 mrem/yr following remedial action. The DOE residual radioactive material guideline computer code, RESRAD, which implements the methodology described in the DOE manual for implementing residual radioactive material guidelines, was used in this evaluation

Effects of 0.12 and 0.80 ppm ozone on rat nasal and nasopharyngeal epithelial mucosubstances: Quantitative histochemistry

International Nuclear Information System (INIS)

Harkema, J.R.; Hotchkiss, J.A.; Henderson, R.F.

1989-01-01

The present study was designed to characterize the quantity of mucosubstances in surface epithelia of the rat nasal cavity and nasopharynx after short-term ozone exposure. Rats were exposure. Nasal cavities were processed for morphometric analysis of intraepithelial mucosubstances. Compared to controls, rats exposed to 0.12 ppm ozone had increased amounts of stored mucosubstances within epithelium lining the medial aspect of the nasal turbinate, but no change within the epithelium of the nasopharynx. Rats exposed to 0.8 ppm ozone had increased quantities of stored mucosubstances within the transitional and respiratory epithelia lining turbinates and lateral walls of the anterior nasal airway, and significant decreases in stored mucosubstances within the epithelium of the nasal septum at the end of exposure. Seven days after the end of exposure, the amounts of intraepithelial mucosubstances returned to control levels along the septum, but remained greater than those of controls along the turbinates and nasopharynx. We conclude that exposures to ambient levels of ozone induce significant changes in the stored secretory product of nasal epithelium in the rat, and that these changes persist for at least 7 days after cessation of exposure

A survey of residual analysis and a new test of residual trend.

Science.gov (United States)

McDowell, J J; Calvin, Olivia L; Klapes, Bryan

2016-05-01

A survey of residual analysis in behavior-analytic research reveals that existing methods are problematic in one way or another. A new test for residual trends is proposed that avoids the problematic features of the existing methods. It entails fitting cubic polynomials to sets of residuals and comparing their effect sizes to those that would be expected if the sets of residuals were random. To this end, sampling distributions of effect sizes for fits of a cubic polynomial to random data were obtained by generating sets of random standardized residuals of various sizes, n. A cubic polynomial was then fitted to each set of residuals and its effect size was calculated. This yielded a sampling distribution of effect sizes for each n. To test for a residual trend in experimental data, the median effect size of cubic-polynomial fits to sets of experimental residuals can be compared to the median of the corresponding sampling distribution of effect sizes for random residuals using a sign test. An example from the literature, which entailed comparing mathematical and computational models of continuous choice, is used to illustrate the utility of the test. © 2016 Society for the Experimental Analysis of Behavior.

Monitoring of Pesticide Residues in Commonly Used Fruits and Vegetables in Kuwait.

Science.gov (United States)

Jallow, Mustapha F A; Awadh, Dawood G; Albaho, Mohammed S; Devi, Vimala Y; Ahmad, Nisar

2017-07-25

The presence of pesticide residues in primary and derived agricultural products raises serious health concerns for consumers. The aim of this study was to assess the level of pesticide residues in commonly consumed fruits and vegetables in Kuwait. A total of 150 samples of different fresh vegetables and fruits were analyzed for the presence of 34 pesticides using the quick easy cheap effective rugged and safe (QuEChERS) multi-residue extraction, followed by gas chromatography-mass spectrometry (GC-MS) or liquid chromatography-tandem mass spectrometry (LC - MS / MS). Pesticide residues above the maximum residue limits (MRL) were detected in 21% of the samples and 79% of the samples had no residues of the pesticides surveyed or contained residues below the MRL. Multiple residues were present in 40% of the samples with two to four pesticides, and four samples were contaminated with more than four pesticide residues. Of the pesticides investigated, 16 were detected, of which imidacloprid, deltamethrin, cypermethrin, malathion, acetamiprid, monocrotophos, chlorpyrifos-methyl, and diazinon exceeded their MRLs. Aldrin, an organochlorine pesticide, was detected in one apple sample, with residues below the MRL. The results indicate the occurrence of pesticide residues in commonly consumed fruits and vegetables in Kuwait, and pointed to an urgent need to develop comprehensive intervention measures to reduce the potential health risk to consumers. The need for the regular monitoring of pesticide residues and the sensitization of farmers to better pesticide safety practices, especially the need to adhere to recommended pre-harvest intervals is recommended.

Monitoring of Pesticide Residues in Commonly Used Fruits and Vegetables in Kuwait

Directory of Open Access Journals (Sweden)

Mustapha F. A. Jallow

2017-07-01

Full Text Available The presence of pesticide residues in primary and derived agricultural products raises serious health concerns for consumers. The aim of this study was to assess the level of pesticide residues in commonly consumed fruits and vegetables in Kuwait. A total of 150 samples of different fresh vegetables and fruits were analyzed for the presence of 34 pesticides using the quick easy cheap effective rugged and safe (QuEChERS multi-residue extraction, followed by gas chromatography-mass spectrometry (GC-MS or liquid chromatography-tandem mass spectrometry (LC-MS/MS. Pesticide residues above the maximum residue limits (MRL were detected in 21% of the samples and 79% of the samples had no residues of the pesticides surveyed or contained residues below the MRL. Multiple residues were present in 40% of the samples with two to four pesticides, and four samples were contaminated with more than four pesticide residues. Of the pesticides investigated, 16 were detected, of which imidacloprid, deltamethrin, cypermethrin, malathion, acetamiprid, monocrotophos, chlorpyrifos-methyl, and diazinon exceeded their MRLs. Aldrin, an organochlorine pesticide, was detected in one apple sample, with residues below the MRL. The results indicate the occurrence of pesticide residues in commonly consumed fruits and vegetables in Kuwait, and pointed to an urgent need to develop comprehensive intervention measures to reduce the potential health risk to consumers. The need for the regular monitoring of pesticide residues and the sensitization of farmers to better pesticide safety practices, especially the need to adhere to recommended pre-harvest intervals is recommended.

40 CFR 180.111 - Malathion; tolerances for residues.

Science.gov (United States)

2010-07-01

..., sugar, tops 8 Blackberry 8 Blueberry 8 Boysenberry 8 Carrot, roots 8 Chayote, fruit 8 Chayote, roots 8... removed 2 Cowpea, forage 135 Cowpea, hay 135 Cranberry 8 Cucumber 8 Currant 8 Date, dried fruit 8 Dewberry... in the drying of grape (raisins). (iii) Total residues of malathion resulting from drying of grape on...

Bioavailability of residual polycyclic aromatic hydrocarbons following enhanced natural attenuation of creosote-contaminated soil

Energy Technology Data Exchange (ETDEWEB)

Juhasz, Albert L., E-mail: albert.juhasz@unisa.edu.a [Centre for Environmental Risk Assessment and Remediation, University of South Australia, Mawson Lakes Campus, SA 5095 (Australia); Smith, Euan [Centre for Environmental Risk Assessment and Remediation, University of South Australia, Mawson Lakes Campus, SA 5095 (Australia); Waller, Natasha [CSIRO Land and Water, Glen Osmond, SA 5064 (Australia); Stewart, Richard [Remediate, Kent Town, SA 5067 (Australia); Weber, John [Centre for Environmental Risk Assessment and Remediation, University of South Australia, Mawson Lakes Campus, SA 5095 (Australia)

2010-02-15

The impact of residual PAHs (2250 +- 71 mug total PAHs g{sup -1}) following enhanced natural attenuation (ENA) of creosote-contaminated soil (7767 +- 1286 mug total PAHs g{sup -1}) was assessed using a variety of ecological assays. Microtox{sup TM} results for aqueous soil extracts indicated that there was no significant difference in EC{sub 50} values for uncontaminated, pre- and post-remediated soil. However, in studies conducted with Eisenia fetida, PAH bioaccumulation was reduced by up to 6.5-fold as a result of ENA. Similarly, Beta vulgaris L. biomass yields were increased 2.1-fold following ENA of creosote-contaminated soil. While earthworm and plant assays indicated that PAH bioavailability was reduced following ENA, the residual PAH fraction still exerted toxicological impacts on both receptors. Results from this study highlight that residual PAHs following ENA (presumably non-bioavailable to bioremediation) may still be bioavailable to important receptor organisms such as earthworms and plants. - Residual PAHs in creosote-contaminated soil following enhanced natural attenuation impacted negatively on ecological receptors.

Bioavailability of residual polycyclic aromatic hydrocarbons following enhanced natural attenuation of creosote-contaminated soil

International Nuclear Information System (INIS)

Juhasz, Albert L.; Smith, Euan; Waller, Natasha; Stewart, Richard; Weber, John

2010-01-01

The impact of residual PAHs (2250 ± 71 μg total PAHs g -1 ) following enhanced natural attenuation (ENA) of creosote-contaminated soil (7767 ± 1286 μg total PAHs g -1 ) was assessed using a variety of ecological assays. Microtox TM results for aqueous soil extracts indicated that there was no significant difference in EC 50 values for uncontaminated, pre- and post-remediated soil. However, in studies conducted with Eisenia fetida, PAH bioaccumulation was reduced by up to 6.5-fold as a result of ENA. Similarly, Beta vulgaris L. biomass yields were increased 2.1-fold following ENA of creosote-contaminated soil. While earthworm and plant assays indicated that PAH bioavailability was reduced following ENA, the residual PAH fraction still exerted toxicological impacts on both receptors. Results from this study highlight that residual PAHs following ENA (presumably non-bioavailable to bioremediation) may still be bioavailable to important receptor organisms such as earthworms and plants. - Residual PAHs in creosote-contaminated soil following enhanced natural attenuation impacted negatively on ecological receptors.

77 FR 43562 - Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2012-07-25

... and sheep at 0.2 ppm; meat of cattle, goat, horse and sheep at 0.1 ppm; meat byproducts of cattle, goat, horse and sheep at 0.25 ppm; fat and meat of hog at 0.01 ppm; meat byproducts of hog at 0.04 ppm.../ [[Page 43564

±25ppm repeatable measurement of trapezoidal pulses with 5MHz bandwidth

CERN Document Server

AUTHOR|(SzGeCERN)712364; Arpaia, Pasquale; Cerqueira Bastos, Miguel; Martino, Michele

2015-01-01

High-quality measurements of pulses are nowadays widely used in fields such as radars, pulsed lasers, electromagnetic pulse generators, and particle accelerators. Whilst literature is mainly focused on fast systems for nanosecond regime with relaxed metrological requirements, in this paper, the high-performance measurement of slower pulses in microsecond regime is faced. In particular, the experimental proof demonstration for a 15 MS/s,_25 ppm repeatable acquisition system to characterize the flat-top of 3 ms rise-time trapezoidal pulses is given. The system exploits a 5MHz bandwidth circuit for analogue signal processing based on the concept of flat-top removal. The requirements, as well as the conceptual and physical designs are illustrated. Simulation results aimed at assessing the circuit performance are also presented. Finally, an experimental case study on the characterization of a pulsed power supply for the klystrons modulators of the Compact Linear Collider (CLIC) under study at CERN is reported. In ...

75 FR 26673 - Clethodim; Pesticide Tolerances

Science.gov (United States)

2010-05-12

... regulation establishes tolerances for residues of clethodim in or on the raw agricultural commodity artichoke... clethodim, in or on the raw agricultural commodity artichoke, globe at 1.3 parts per million (ppm... bushberry subgroup 13-07B tolerance from 3.0 ppm to 0.20 ppm and the globe artichoke tolerance from 1.3 ppm...

Hazardous properties of paint residues from the furniture industry.

Science.gov (United States)

Vaajasaari, Kati; Kulovaara, Maaret; Joutti, Anneli; Schultz, Eija; Soljamo, Kari

2004-01-30

The objective of this study was to screen nine excess paint residues for environmental hazard and to evaluate their disposability in a non-hazardous or hazardous-waste landfill. These residues were produced in the process of spray-painting furniture. Residues were classified according to their leaching and ecotoxicological properties. Leaching properties were determined with the European standard SFS-EN 12457-2 leaching-test. The toxicity of the leaching-test eluates was measured with plant-, bacteria- and enzyme-inhibition bioassays. Total organic carbon, formaldehyde and solvent concentrations in the solid wastes and in the leaching-test eluates were analysed. It seemed likely that leached formaldehyde caused very high acute toxicity in leaching-test eluates of the dry-booth residues. This hypothesis was based on the fact that the formaldehyde concentrations in the leaching-test eluates of the dry-booth residues were 62-75 times higher than the EC50 value reported in the literature for formaldehyde. The results of the water-curtain booth residues showed that the samples with the highest TOC and aromatic solvent concentrations were also the most toxic. The studied excess paint residues were complex organic mixtures and contained large amounts of compounds not identifiable from chemical data. Therefore, the evaluation of the hazard based solely on available chemical data is unlikely to be sufficient, as evidenced by our study. Our results show that harmful compounds remain in the solid waste and the toxicity results of their leaching-test eluates show that toxicity may leach from residues in contact with water at landfill sites. They also confirm the benefit of combining chemical and ecotoxicological assays in assessing the potential environmental hazard of complex organic mixtures found in wastes. Copyright 2003 Elsevier B.V.

Anion induced conformational preference of Cα NN motif residues in functional proteins.

Science.gov (United States)

Patra, Piya; Ghosh, Mahua; Banerjee, Raja; Chakrabarti, Jaydeb

2017-12-01

Among different ligand binding motifs, anion binding C α NN motif consisting of peptide backbone atoms of three consecutive residues are observed to be important for recognition of free anions, like sulphate or biphosphate and participate in different key functions. Here we study the interaction of sulphate and biphosphate with C α NN motif present in different proteins. Instead of total protein, a peptide fragment has been studied keeping C α NN motif flanked in between other residues. We use classical force field based molecular dynamics simulations to understand the stability of this motif. Our data indicate fluctuations in conformational preferences of the motif residues in absence of the anion. The anion gives stability to one of these conformations. However, the anion induced conformational preferences are highly sequence dependent and specific to the type of anion. In particular, the polar residues are more favourable compared to the other residues for recognising the anion. © 2017 Wiley Periodicals, Inc.

Selected trace elements and organochlorines: some findings in blood and eggs of nesting common eiders (Somateria mollissima) from Finland

Science.gov (United States)

Franson, J. Christian; Hollmen, Tuula E.; Poppenga, Robert H.; Hario, Martti; Kilpi, Mikael; Smith, Milton R.

2000-01-01

In 1997 and 1998, we collected blood samples from nesting adult female common eiders (Somateria mollissima) at five locations in the Baltic Sea near coastal Finland and analyzed them for lead, selenium, mercury, and arsenic. Eggs were collected from three locations in 1997 for analysis of selenium, mercury, arsenic, and 17 organochlorines (OCs). Mean blood lead concentrations varied by location and year and ranged from 0.02 ppm (residues in blood on wet weight basis) to 0.12 ppm, although one bird had 14.2 ppm lead in its blood. Lead residues in the blood of eiders were positively correlated with the stage of incubation, and lead inhibited the activity of the enzyme delta-aminolevulinic acid dehydratase (ALAD) in the blood. Selenium concentrations in eider blood varied by location, with means of 1.26 to 2.86 ppm. Median residues of selenium and mercury in eider eggs were 0.55 and 0.10 ppm (residues in eggs on fresh weight basis), respectively, and concentrations of both selenium and mercury in eggs were correlated with those in blood. Median concentrations of p,pa??-dichlorodiphenyldichloroethylene in eggs ranged from 13.1 to 29.6 ppb, but all other OCs were below detection limits. The residues of contaminants that we found in eggs were below concentrations generally considered to affect avian reproduction. The negative correlation of ALAD activity with blood lead concentrations is evidence of an adverse physiological effect of lead exposure in this population.

Partial sums of lagged cross-products of AR residuals and a test for white noise

NARCIS (Netherlands)

de Gooijer, J.G.

2008-01-01

Partial sums of lagged cross-products of AR residuals are defined. By studying the sample paths of these statistics, changes in residual dependence can be detected that might be missed by statistics using only the total sum of cross-products. Also, a test statistic for white noise is proposed. It is

Cellulosic ethanol production from agricultural residues in Nigeria

International Nuclear Information System (INIS)

Iye, Edward; Bilsborrow, Paul

2013-01-01

Nigeria′s Biofuels Policy introduced in 2007 mandates a 10% blend (E10) of bioethanol with gasoline. This study investigates the potential for the development of a cellulosic ethanol industry based on the availability of agricultural residues and models the number of commercial processing facilities that could be sited in the six Geo-political zones. The potential for cellulosic ethanol production from agricultural residues in Nigeria is 7556 km 3 per annum exceeding the mandate of 10% renewable fuel required and providing the potential for 12 large- and 11 medium-scale processing facilities based on the use of a single feedstock. Cassava and yam peelings provided in excess of 80% of the process residues available with enough feedstock to supply 10 large-scale facilities with a fairly even distribution across the zones. Sorghum straw, millet straw and maize stalks represented 75% of the potential resource available from field residues with the potential to supply 2 large- and 7 medium-scale processing facilities, all of which would be located in the north of the country. When a multi-feedstock approach is used, this provides the potential for either 29 large- or 58 medium-scale facilities based on outputs of 250 and 125 km 3 per annum respectively. - Highlights: • Nigeria′s Biofuels Policy mandates a 10% blend of bioethanol with gasoline. • Total bioethanol production from agricultural residues was 7556 km 3 per annum. • Process residues offer the greatest potential accounting for 62% of production. • Nigeria has the potential for 12 large- and 11 medium scale commercial. • The use of mixed feedstocks significantly increases the potential for production

Annatto seed residue (Bixa orellana L.: nutritional quality

Directory of Open Access Journals (Sweden)

Melissa Alessandra Valério

2015-06-01

Full Text Available Considering that annatto seeds are rich in protein, the present work aimed to evaluate the biological quality of this nutrient in the meal residue originating from annatto seed processing. We determined the general composition, mineral levels, amino acid composition and chemical scores, antinutritional factors, and protein quality using biological assays. The following values were obtained: 11.50% protein, 6.74% moisture, 5.22% ash, 2.22% lipids, 42.19% total carbohydrates and 28.45% fiber. The residue proved to be a food rich in fiber and also a protein source. Antinutritional factors were not detected. The most abundant amino acids were lysine, phenylalanine + tyrosine, leucine and isoleucine. Valine was the most limiting amino acid (chemical score 0.22. The protein quality of the seed residue and the isolated protein showed no significant differences. The biological value was lower than that of the control protein but higher than that found in other vegetables. Among the biochemical analyses, only creatinine level was decreased in the two test groups compared to the control group. Enzyme tests did not indicate liver toxicity. The results showed favorable aspects for the use of annatto seed residue in the human diet, meriting further research.

Renewable energy from agro-residues in China. Solid biofuels and biomass briquetting technology

Energy Technology Data Exchange (ETDEWEB)

Chen, Longjian; Han, Lujia [Center for Biomass Resource Utilization, College of Engineering, China Agricultural University (East Campus), 17 Qing-Hua-Dong-Lu, Hai-Dian District, Beijing 100083 (China); Xing, Li [Service Center for Trading Technology Service, Chinese Academy of Agricultural Mechanization Sciences, Beijing 100083 (China)

2009-12-15

China has the abundant agro-residue resources, producing more than 630 million tons of agro-residues in 2006, and amounting to about 20% of total energy consumption in rural areas. Efficient utilization of enormous agro-residues resource is crucial for providing bioenergy, releasing risk of environmental pollution, and increasing farmers' income. The paper presented the feasibility of densified solid biofuels technology for utilizing agro-residues in China. The output and distribution of agro-residues in recent 10 years, the R and D of briquetting technology, and the market of densified solid biofuels from agro-residues in China have been analyzed. The result indicated that the abundant agro-residue resources can provide the economical and sustainable raw material for densified solid biofuels development in China. The R and D of briquetting technology at present can strongly support the large scale production of densified solid biofuels. With continued improvement and cost reduction of briquetting technology, along with the support of nation energy policy on biomass energy, the market of densified solid biofuels from agro-residues in China will be more fully deployed. Based on the above mentioned key factors, development of densified solid biofuels from agro-residues in China will be promising and feasible. (author)

Renewable energy from agro-residues in China. Solid biofuels and biomass briquetting technology

International Nuclear Information System (INIS)

Chen, Longjian; Han, Lujia; Xing, Li

2009-01-01

China has the abundant agro-residue resources, producing more than 630 million tons of agro-residues in 2006, and amounting to about 20% of total energy consumption in rural areas. Efficient utilization of enormous agro-residues resource is crucial for providing bioenergy, releasing risk of environmental pollution, and increasing farmers' income. The paper presented the feasibility of densified solid biofuels technology for utilizing agro-residues in China. The output and distribution of agro-residues in recent 10 years, the R and D of briquetting technology, and the market of densified solid biofuels from agro-residues in China have been analyzed. The result indicated that the abundant agro-residue resources can provide the economical and sustainable raw material for densified solid biofuels development in China. The R and D of briquetting technology at present can strongly support the large scale production of densified solid biofuels. With continued improvement and cost reduction of briquetting technology, along with the support of nation energy policy on biomass energy, the market of densified solid biofuels from agro-residues in China will be more fully deployed. Based on the above mentioned key factors, development of densified solid biofuels from agro-residues in China will be promising and feasible. (author)

78 FR 57276 - Quinoxyfen; Pesticide Tolerances

Science.gov (United States)

2013-09-18

... or on grape; pepper, bell; pepper, nonbell; and strawberry as they will be superseded by crop group... grape at 0.60 ppm; strawberry at 0.90 ppm; pepper, bell at 0.35 ppm; and pepper, nonbell at 1.7 ppm, as..., strawberries, and peppers. EPA is raising the level of the requested U.S. tolerances for residues of quinoxyfen...

Residue preference mapping of ligand fragments in the Protein Data Bank.

Science.gov (United States)

Wang, Lirong; Xie, Zhaojun; Wipf, Peter; Xie, Xiang-Qun

2011-04-25

The interaction between small molecules and proteins is one of the major concerns for structure-based drug design because the principles of protein-ligand interactions and molecular recognition are not thoroughly understood. Fortunately, the analysis of protein-ligand complexes in the Protein Data Bank (PDB) enables unprecedented possibilities for new insights. Herein, we applied molecule-fragmentation algorithms to split the ligands extracted from PDB crystal structures into small fragments. Subsequently, we have developed a ligand fragment and residue preference mapping (LigFrag-RPM) algorithm to map the profiles of the interactions between these fragments and the 20 proteinogenic amino acid residues. A total of 4032 fragments were generated from 71 798 PDB ligands by a ring cleavage (RC) algorithm. Among these ligand fragments, 315 unique fragments were characterized with the corresponding fragment-residue interaction profiles by counting residues close to these fragments. The interaction profiles revealed that these fragments have specific preferences for certain types of residues. The applications of these interaction profiles were also explored and evaluated in case studies, showing great potential for the study of protein-ligand interactions and drug design. Our studies demonstrated that the fragment-residue interaction profiles generated from the PDB ligand fragments can be used to detect whether these fragments are in their favorable or unfavorable environments. The algorithm for a ligand fragment and residue preference mapping (LigFrag-RPM) developed here also has the potential to guide lead chemistry modifications as well as binding residues predictions.

40 CFR 80.527 - Under what conditions may motor vehicle diesel fuel subject to the 15 ppm sulfur standard be...

Science.gov (United States)

2010-07-01

... vehicle diesel fuel subject to the 15 ppm sulfur standard be downgraded to motor vehicle diesel fuel... Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.527 Under what conditions may motor vehicle diesel fuel subject to the 15...

Wheat nitrogen fertilizer residues on an ultisol from the IX Region

International Nuclear Information System (INIS)

Rouanet M, Juan Luis; Pino N, Ines; Nario M, Adriana; Jobet, Claudio; Parada V, Ana Maria; Videla L, Ximena

2005-01-01

The soil nitrogen fertilizer residue is a relevant issue on a wheat production system at the IX Region of Chile, due to the high level of yield and use of resources, having an environmental impact from the use of fertilizer economy. The N-soil residue, not absorb by the plant, can be leach and contaminate the groundwater with nitrates or be redistributed by erosion. The application of isotopic techniques, using fertilizer labeled with 15 N, providing the quantitative information of the fate of this nutrient in the plant-soil system, important in the rate formulation based on the nitrogen use efficiency and in the benefit/cost relation. An assay was carried out in an Ultisol Metrenco Soil (Family fine, mixed, mesic, Typic Paleudults) at Pumalal locality. A Kumpa wheat variety was used, with a control treatment and five N rates applied as Urea labeled with 10% 15 N a.e., split in four times during the crop growth cycle. Total N (Kjeldhal) and 15 N optical emission spectrometer were determined in grain and straw samples harvested in February. Before to the next sow on may, soil sample were taken with an 3 cm diameter hugger (0-20; 20-40 and 40-60 cm depth). The samples were air dried, sieved and analyzed for total N and 15 N. The parameters determined for each depth were: N total (%), 15 N a.e. to obtain the plant-soil system N fertilizer recovery and its N residues in the soil profile. The wheat yield obtained was related with a cubic model using the N fertilizer rate applied (R 2 =0.75). The highest yield for the grain, 9.8 Mg ha -1 , was obtained applying 197 k ha -1 of N, with 45% of 15 N recovered by the grain. Nevertheless, the soil-crop system obtained a high 15 N recovery (>88%), in the soil remained 32-60% as N residue, being not used by the plant during the growth period. Between 27-54% of the 15 N total residue was found at the 0-20 cm soil depth, portion that is susceptible of distribution by erosion, implied in the use of fertilizer economy. Around 4

A study on the production of agricultural residues in Italy

Energy Technology Data Exchange (ETDEWEB)

Di Blasi, C.; Tanzi, V.; Lanzetta, M. [Universita degli Studi di Napoli Federico II, Dip di Ingegneria Chimica, Napoli (Italy)

1997-12-01

The Italian production of agricultural residues has been evaluated with a view to energy recovery through gasification. Two main categories of residues have been identified: the first, (A) is associated with the growing and collection of products with a nutritional value, whereas the second (B) includes the residues associated with the subsequent processing in order to obtain final products for commercialization. Category A, which comprises three further sub-categories: straw (A1); woody residues (A2); and stems and leaves (residues from vegetables, tobacco, sugar beet, (A3)), results in about 16.5 mt yr. The average amount of straw (A1) is 11 mt/yr, of which about 60% is waste to be eliminated. Woody residues (A2) (mainly pruning off-cuts from vineyards and olive groves) are about 3.5 mt/yr (85% unused). Category A3 amounts to about 2 mt/yr (90% unused). Straw is available mainly in the northern part of the country, whereas the other two sub-categories are widely distributed in central and southern regions. The yields of category B are estimated at 4 mt/yr, of which more than 3 mt/yr are waste products from grape and olive processing. Other residues, such as rice, sunflower and soya-bean husks (about 0.65 mt/yr), almond and nut shells and fruit stones (about 0.2 mt/yr), although not widely available on a national scale, can be significant on a local basis. The total amount of unused agricultural residues is about 14.5 mt/yr, which, if completely exploited through gasification, can contribute as much as 7-10% to the current national electricity needs. The regions of Veneto, Puglia, Friuli, Lombardia and Emilia Romagna appear to be good candidates for electricity production, given the significant surface concentration of unused residues (105-55 t km{sup 2}). (author)

Interactions Between Agricultural Chemicals and the Soil Microflora and Their Effects on {sup 14}C-Parathion Metabolism in Cranberry Soils

Energy Technology Data Exchange (ETDEWEB)

Ferris, I. G.; Lichtenstein, E. P. [Department of Entomology, University of Wisconsin, Madison, Wisconsin 53706 (United States)

1981-05-15

Full text: The fate of {sup 14}C-parathion in a loam and ''cranberry soil'' was investigated utilizing a closed system to enable monitoring of {sup 14}CO{sub 2} evolution, and to obtain a total {sup 14}C balance. Soils were treated with {sup 14}C-parathion at rates equivalent to about 3 ppm and incubated at 23 ± 2°C. After 3 weeks of soil incubation differences in the persistence of {sup 14}C-parathion were evident: 76% of applied radiocarbon remained as unchanged parathion in loam soil compared with only 4% in a cranberry soil; conversely, {sup 14}C-degradation products amounted to 26% and 91% of applied radiocarbon, respectively. Interactions were found to occur between fungicides and the biodegradation of {sup 14}C-(ring)-parathion in cranberry soil. Captafol (Difolatan® inhibited the metabolism of {sup 14}C-parathion. The inhibition was a linear function of the applied captafol concentration with a no effect concentration of 1 ppm. On the other hand, 100 ppm of Manzate®(maneb) or Benlate® (benomyl) altered the pathway of {sup 14}C-parathion degradation in favour of bound {sup 14}C-residues. In soil-free medium inoculated with cranberry soil microorganisms {sup 14}C-(ring)- parathion was degraded within 4 days principally to volatile {sup 14}C-compounds (presumably {sup 14}CO{sub 2}). On the -contrary, no degradation of {sup 14}C-parathion occurred in an inoculated medium that also contained a 100-ppm benomyl suspension, apparently benomyl inhibited the hydrolysis/oxidation of {sup 14}C-parathion. Soil amendments of 100 ppm nitrogen (N) as (NH{sub 4}){sub 2}SO{sub 4}, or to a lesser extent KNO{sub 3}, inhibited the metabolism of {sup 14}C-( ring)-parathion to {sup 14}CO{sub 2}. In summary, some agricultural chemicals have an effect on parathiondegrading microorganisms resulting in an increase in bound {sup 14}C-residues and an increased persistence of toxic parathion residues.

Evaluation of residue-residue contact predictions in CASP9

KAUST Repository

Monastyrskyy, Bohdan; Fidelis, Krzysztof; Tramontano, Anna; Kryshtafovych, Andriy

2011-01-01

This work presents the results of the assessment of the intramolecular residue-residue contact predictions submitted to CASP9. The methodology for the assessment does not differ from that used in previous CASPs, with two basic evaluation measures

Determination of total arsenic in soil and arsenic-resistant bacteria from selected ground water in Kandal Province, Cambodia

International Nuclear Information System (INIS)

Hamzah, A.; Wong, K.K.; Hasan, F.N.; Mustafa, S.; Khoo, K.S.; Sarmani, S.B.

2013-01-01

Cambodia has geological environments conducive to generation of high-arsenic groundwater and people are at high risk of chronic arsenic exposure. The aims of this study are to investigate the concentration of total arsenic and to isolate and identify arsenic-resistant bacteria from selected locations in Kandal Province, Cambodia. The INAA technique was used to measure the concentration of total arsenic in soils. The arsenic concentrations in soils were above permissible 5 mg/kg, ranging from 5.34 to 27.81 mg/kg. Bacteria resistant to arsenic from two arsenic-contaminated wells in Preak Russey were isolated by enrichment method in nutrient broth (NB). Colonies isolated from NB was then grown on minimal salt media (MSM) added with arsenic at increasing concentrations of 10, 20, 30, 50, 100 and 250 ppm. Two isolates that can tolerate 750 ppm of arsenic were identified as Enterobacter agglomerans and Acinetobacter lwoffii based on a series of biochemical, physiological and morphological analysis. Optimum growth of both isolates ranged from pH 6.6 to 7.0 and 30-35 deg C. E. agglomerans and A. lwoffii were able to remove 66.4 and 64.1 % of arsenic, respectively at the initial concentration of 750 ppm, within 72 h of incubation. Using energy dispersive X-ray technique, the percentage of arsenic absorbed by E. agglomerans and A. lwoffii was 0.09 and 0.15 %, respectively. This study suggested that arsenic-resistant E. agglomerans and A. lwoffii removed arsenic from media due to their ability to absorb arsenic. (author)

Presence of Aeromonas spp in water from drinking-water- and wastewater-treatment plants in Mexico City.

Science.gov (United States)

Villarruel-López, Angélica; Fernández-Rendón, Elizabeth; Mota-de-la-Garza, Lydia; Ortigoza-Ferado, Jorge

2005-01-01

The frequency of Aeromonas spp in three wastewater-treatment plants (WWTPs) and two drinking-water plants (DWPs) in México City was determined. Samples were taken throughout a year by the Moore's swab technique. A total of 144 samples were obtained from WWTPs and 96 from DWPs of both incoming and outflowing water. Aeromonas spp was isolated in 31% of the samples, from both kinds of sources. The technique used for the isolation of the pathogen was suitable for samples with high associate microbiota content and for those with a scarce microbial content. The presence of mesophilic-aerobic, coliform, and fecal-coliform organisms was investigated to determine whether there was any correlation with the presence of Aeromonas spp. Most samples from WWTP, which did not comply with the Mexican standards, had the pathogen, and some of the samples from the outflow of the DWP, which were within the limits set by the Mexican standards, also had Aeromonas spp. Most samples containing Aeromonas spp. had concentrations below 0.1 ppm residual chlorine, and the strains were resistant to 0.3 ppm, which supports the recommendation to increase the residual chlorine concentration to 0.5 to 1.0 ppm, as recommended by the Mexican standards.

Short-term contributions of cover crop surface residue return to soil carbon and nitrogen contents in temperate Australia.

Science.gov (United States)

Zhou, Xiaoqi; Wu, Hanwen; Li, Guangdi; Chen, Chengrong

2016-11-01

Cover crop species are usually grown to control weeds. After cover crop harvest, crop residue is applied on the ground to improve soil fertility and crop productivity. Little information is available about quantifying the contributions of cover crop application to soil total carbon (C) and nitrogen (N) contents in temperate Australia. Here, we selected eight cover crop treatments, including two legume crops (vetch and field pea), four non-legume crops (rye, wheat, Saia oat, and Indian mustard), a mixture of rye and vetch, and a nil-crop control in temperate Australia to calculate the contributions of cover crops (crop growth + residue decomposition) to soil C and N contents. Cover crops were sown in May 2009 (autumn). After harvest, the crop residue was placed on the soil surface in October 2009. Soil and crop samples were collected in October 2009 after harvest and in May 2010 after 8 months of residue decomposition. We examined cover crop residue biomass, soil and crop total C and N contents, and soil microbial biomass C and N contents. The results showed that cover crop application increased the mean soil total C by 187-253 kg ha -1 and the mean soil total N by 16.3-19.1 kg ha -1 relative to the nil-crop treatment, except for the mixture treatment, which had similar total C and N contents to the nil-crop control. Cover crop application increased the mean soil microbial biomass C by 15.5-20.9 kg ha -1 and the mean soil microbial biomass N by 4.5-10.2 kg ha -1 . We calculated the apparent percentage of soil total C derived from cover crop residue C losses and found that legume crops accounted for 10.6-13.9 %, whereas non-legume crops accounted for 16.4-18.4 % except for the mixture treatment (0.2 %). Overall, short-term cover crop application increased soil total C and N contents and microbial biomass C and N contents, which might help reduce N fertilizer use and improve sustainable agricultural development.

Analysis of fenbendazole residues in bovine milk by ELISA.

Science.gov (United States)

Brandon, David L; Bates, Anne H; Binder, Ronald G; Montague, William C; Whitehand, Linda C; Barker, Steven A

2002-10-09

Fenbendazole residues in bovine milk were analyzed by ELISAs using two monoclonal antibodies. One monoclonal antibody (MAb 587) bound the major benzimidazole anthelmintic drugs, including fenbendazole, oxfendazole, and fenbendazole sulfone. The other (MAb 591) was more specific for fenbendazole, with 13% cross-reactivity with the sulfone and no significant binding to the sulfoxide metabolite. The limit of detection of the ELISA method in the milk matrix was 7 ppb for MAb 587 and 3 ppb for MAb 591. Fenbendazole was administered in feed, drench, and paste form to three groups of dairy cattle. Milk was collected immediately before dosing and then every 12 h for 5 days. The ELISA indicated that residue levels varied widely among individual cows in each group. Fenbendazole levels peaked at approximately 12-24 h and declined rapidly thereafter. Metabolites were detected at much higher levels than the parent compound, peaked at approximately 24-36 h, and declined gradually. Residue levels were undetectable by 72 h. The ELISA data correlated well with the total residues determined by chromatographic analysis, but the use of the two separate ELISAs did not afford an advantage over ELISA with the single, broadly reactive MAb 587. The ELISA method could be used to flag high-residue samples in on-site monitoring of fenbendazole in milk and is a potential tool for studying drug pharmacokinetics.

Report of the Task Force on Sawmill Wood Residue Management

International Nuclear Information System (INIS)

1993-11-01

The Sawmill Wood Residue Task Force was established in 1993 to seek solutions to managing wood residue at sawmills, shingle mills, and log sort yards in British Columbia without burning or landfilling. In particular, the Task Force was formed to address the phaseout of beehive-type wood waste burners by January 1, 1996. The Task Force was formed at the forest product industry's request and included representatives from industry associations and government. It reviewed existing information on the quantities of mill residues and the options available for reducing, reusing, and recycling the residues. Nearly half of all the province's residues of 5 million bone dry tonnes/y is disposed of by burning with no energy recovery, or by landfilling. It was recognized that the total volume of wood residue cannot be handled by any one method suitable for all sources but that in the near term, electricity generation could deal with a significant percentage of wood currently being burned. The most immediate technically viable opportnity by industry in this area may be in cogeneration of electricity for load displacement at pulp mills. Other opportunities exist such as conversion of wood residue to liquid fuels but these require greater commitments to research and development. The need to handle bark and sawdust was identified as a critical requirement for alternate uses. Small niche uses for wood residue must be examined on a case by case basis for each company or group of companies in a region. The provincial government can also promote better use of wood wastes through policies such as social costing of power generation options and sales tax exemption for ethanol fuel. 1 tab

Effect of shot peening treatment in the behavior of residual stress in duplex stainless steel during medium cycle fatigue

International Nuclear Information System (INIS)

Pedrosa, Peter D.S.; Rebello, Joao Marcos A.; Fonseca, Maria P. Cindra

2010-01-01

The lifetime of duplex stainless steel parts experiencing cyclic fatigue is directly influenced by the residual stresses present in the ferrite and austenite phases. The motivation for this work was to analyze the behaviour of the residual stresses fields introduced by shot peening treatment in both phases, in the sample surface as in the subsurface layers, in low fatigue cycles, using the X-rays diffraction technique. The results shows that the compressive residual stresses introduced by the shot peening treatment in both phases improved fatigue life of the material. However, the cyclical loads produce partial or total relief in these residual stresses fields. It was verified that the shot peening process induced the formation of microcracks only in the ferrite phase. The largest variations in the total compressive residual stresses fields also occurred in this phase. The samples surfaces were analyzed by scanning electron microscopy. (author)

Note on pesticide residues as a function of formulation used

International Nuclear Information System (INIS)

Lord, K.A.

1976-01-01

The total quantities of pesticides needed for adequate pest control may be minimized by the correct choice of methods of formulation and application. This will diminish the total burden of residues in the environment but not necessarily in the crop. Radiolabelled pesticides are useful for small-scale and laboratory tests to elucidate the principles which determine the behaviour of pesticides in the environment and to check analytical methods used for field-scale tests. (author)

Part 1: Logging residues in piles - Needle loss and fuel quality. Part 2: Nitrogen leaching under piles of logging residues

International Nuclear Information System (INIS)

Lehtikangas, P.; Lundkvist, H.

1991-01-01

Part 1: Experimental piles were built in three geographical locations during May-Sept. 1989. Logging residues consisted of 95% spruce and 5% pine. Height of the piles varied between 80 and 230 cm. Needles were collected by placing drawers under 40 randomely chosen piles. The drawers were emptied every two weeks during the storage period. Natural needle loss was between 18 and 32% of the total amount of needles after the first two months of storage. At the end of the storage period, 24-42% of the needles had fallen down to the drawers. At the end of the experiment the total needle fall was 95-100% in the shaken piles. According to the results of this study piles smaller than 150 cm had the most effective needle fall. Piles should be placed on open places where the air and sun heat penetrate and dry them. Needles were the most sensitive fraction to variations in precipitation compared to the other components, such as branches. Piles usually dried quickly, but they also rewet easily. This was especially true in the smaller piles. The lowest moisture content was measured at the end of June. The ash content in needles varied between 4 and 8%. 16 refs., 15 figs. Part 2: Three field experiments were equipped with no-tension humus lysimeters. Pairs of lysimeters with the same humus/field layer vegetation material were placed in pairs, one under a pile of felling residues and another in the open clear felling. Leaching of nitrogen as well as pH and electric conductivity in the leachate was followed through sampling of the leachate at regular intervals. The results from the investigation show that: * the amount of leachate was higher in lysimeters in the open clear felling, * pH in the leachate was initially lower under piles of felling residues, * the amount of nitrogen leached was higher in the open clear felling. Thus, storing of felling residues in piles during the summer season did not cause any increase in nitrogen leaching, which had been considered to be a risk

Enhanced coagulation for improving coagulation performance and reducing residual aluminum combining polyaluminum chloride with diatomite.

Science.gov (United States)

Hu, Wenchao; Wu, Chunde

2016-01-01

The feasibility of using enhanced coagulation, which combined polyaluminum chloride (PAC) with diatomite for improving coagulation performance and reducing the residual aluminum (Al), was discussed. The effects of PAC and diatomite dosage on the coagulation performance and residual Al were mainly investigated. Results demonstrated that the removal efficiencies of turbidity, dissolved organic carbon (DOC), and UV254 were significantly improved by the enhanced coagulation, compared with PAC coagulation alone. Meaningfully, the five forms of residual Al (total Al (TAl), total dissolved Al (TDAl), dissolved organic Al (DOAl), dissolved monomeric Al (DMAl), and dissolved organic monomeric Al (DOMAl)) all had different degrees of reduction in the presence of diatomite and achieved the lowest concentrations (0.185, 0.06, 0.053, 0.014, and 0 mg L(-1), respectively) at a PAC dose of 15 mg L(-1) and diatomite dose of 40 mg L(-1). In addition, when PAC was used as coagulant, the majority of residual Al existed in dissolved form (about 31.14-70.16%), and the content of DOMAl was small in the DMAl.

Rapid Determination of Total Thujone in Absinthe Using 1H NMR Spectroscopy

OpenAIRE

Yulia B. Monakhova; Thomas Kuballa; Dirk W. Lachenmeier

2011-01-01

1H NMR spectroscopy is utilized to quantify total thujone (sum of alpha- and beta-isomers) in absinthe. For sample preparation, a simple dilution with buffer is required. Thujone produces a distinct peak of the CH2 group in the cyclopentanone moiety in the 2.13–2.11 ppm range. No overlap with other typical constituents such as anethole or fenchone occurs. The detection limit of 0.3 mg/L is adequate to control the EU maximum limit. The relative standard deviation was 6%, and linearity was obse...

A new type industrial total station based on target automatic collimation

Science.gov (United States)

Lao, Dabao; Zhou, Weihu; Ji, Rongyi; Dong, Dengfeng; Xiong, Zhi; Wei, Jiang

2018-01-01

In the case of industrial field measurement, the present measuring instruments work with manual operation and collimation, which give rise to low efficiency for field measurement. In order to solve the problem, a new type industrial total station is presented in this paper. The new instrument can identify and trace cooperative target automatically, in the mean time, coordinate of the target is measured in real time. For realizing the system, key technology including high precision absolutely distance measurement, small high accuracy angle measurement, target automatic collimation with vision, and quick precise controlling should be worked out. After customized system assemblage and adjustment, the new type industrial total station will be established. As the experiments demonstrated, the coordinate accuracy of the instrument is under 15ppm in the distance of 60m, which proved that the measuring system is feasible. The result showed that the total station can satisfy most industrial field measurement requirements.

Total reflection x-ray analysis of metals in blood samples

International Nuclear Information System (INIS)

Nakamura, Takuya; Matsui, Hiroshi; Kawamata, Masaya

2009-01-01

The sample preparation for TXRF (total reflection X-ray fluorescence) quantitative analysis of trace elements in human blood samples was investigated. In the TXRF analysis, a solution sample is dropped and dried on a flat substrate, and then the dried residue is measured. In this case, the dried residue should be flat not to disturb X-ray total reflection on the substrate. In addition, it is required to simply measure the whole blood sample by TXRF method, although a serum is analyzed in many cases. Thus, we studied the optimum conditions of the sample preparation of the whole blood by adding the pure water to apply Hemolysis phenomenon, where blood cells are destroyed due to different of the osmotic pressure, leading to flat residue. It was found that the best S/B ratio was obtained when the whole blood was diluted 8 times with pure water. Moreover, it was investigated the influence of the surface chemical condition of the glass substrate on the shape of the dried reside of the blood sample. When the surface of the glass substrate was hydrophilic, the shape of the dried residues was not uniform, as a result, the quantitative data of TXRF analysis gave a large deviation. On the other hand, when the surface of the glass was hydrophobic, the shape of the residue was almost uniform, as a result, a good reproducibility was obtained. Another problem was an outer ring of the dried residue of the blood. This uneven ring absorbs the primary X-rays, caused to low determined quantitative data. Thus, we tried the heating way of the dropped blood sample at a high temperature of 200 degrees. In this case, the blood sample was dried immediately, and a flat homogeneous dried residue was obtained without the outer ring. Using the optimized conditions for sample preparation, human blood sample was quantitatively measured by TXRF and ICP-AES. A good agreement was obtained in TXRF and ICP-AES determinations; however, the measurement of Cl and Br will be an advantage of TXRF, because

Compostagem da fração sólida da água residuária de suinocultura Solid fraction composting of residual water from pig farms

Directory of Open Access Journals (Sweden)

Marco A. P. Orrico Júnior

2009-09-01

Full Text Available Avaliar o desenvolvimento do processo de compostagem utilizando como substrato à fração sólida da água residuária de suinocultura foi o objetivo deste trabalho. Para a obtenção da fração sólida, a água residuária de suinocultura foi submetida ao peneiramento, utilizando-se de peneira com malha de 1 milímetro. Após separação, a fração sólida foi utilizada para a confecção de três leiras de compostagem, em pátio com piso de concreto e cobertura plástica. Durante a compostagem da fração sólida da água residuária de suinocultura, foram avaliados: temperatura, reduções de sólidos totais (ST, sólidos voláteis (SV, demanda química de oxigênio (DQO, carbono orgânico, matéria orgânica compostável (MOC, matéria orgânica resistente à compostagem (MORC, números mais prováveis (NMPs de coliformes totais e coliformes termotolerantes, além do volume e dos teores de nutrientes no composto. A compostagem mostrou-se eficiente no tratamento da fração sólida da água residuária de suinocultura devido à elevada minimização do poder poluente dos dejetos, observando-se reduções de 71,24% nos teores de ST, 64,55% no volume, 56,89% no teor de DQO e 56,89% na MOC. Foram verificadas reduções de 100% nos NMPs de coliformes totais e termotolerantes, o que possibilita seu uso como adubo orgânico.This work aimed to evaluate the development of the composting process by using the solid fraction of residual water from a pig farm. To obtain the solid fraction, the residual water was sewed in a 1mm screen sew. After separation, the solid fraction was used to form three composting piles, on a patio with concrete floor and plastic cover. During composting the solid fraction of residual water from pig farms was monitored: temperature, total solids reduction (TS, volatile solids (VS chemical demand for oxygen (CDO, organic carbon, compostable organic matter (COM, organic matter resistant to composting (OMRC, most probable

78 FR 43115 - Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2013-07-19

...; horseradish at 0.05 ppm; parsley, dry leaves at 8.3 ppm; parsley, leaves at 3.0 ppm; and pea, dry, seed at 0... metabolites convertible to 3,4-dichloroaniline, calculated as linuron, in or on parsley, leaves at 0.25 ppm...

76 FR 22067 - Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2011-04-20

... at 0.02 ppm; alfalfa, forage at 4.5 ppm; alfalfa, hay at 8.0 ppm; avocado at 0.15 ppm; citrus fruit... Tolerance PP 1F7840. (EPA-HQ-OPP-2011-0307). E.I. du Pont de Nemours & Company, 1007 Market Street...

X-ray fractography by using synchrotron radiation source. Residual stress distribution just beneath fatigue fracture surface

International Nuclear Information System (INIS)

Akita, Koichi; Yoshioka, Yasuo; Suzuki, Hiroshi; Sasaki, Toshihiko

2000-01-01

The residual stress distributions just beneath the fatigue fracture surface were measured using synchrotron radiation with three different wavelengths, i.e., three different penetration depths. The residual stress distributions were estimated from three kinds of diffraction data by the following process. First, a temporary residual stress distribution in the depth direction is assumed. Theoretical 2θ-sin 2 ψ diagrams for each wavelength, where each has a different penetration depth, are calculated by the cosψ method developed by one of the authors. The sum total of the differences between the theoretical and experimental values of the diffraction angle in 2θ-sin 2 ψ diagrams is calculated. This total value is minimized by changing the assumed stress distribution by the quasi-Newton optimization method. Finally, optimized 2θ-sin 2 ψ diagrams for each penetration depth and detailed stress distribution are determined. The true surface residual stress is obtained from this stress distribution. No effect of load ratio R (= P min /P max ) on the residual stresses of the fatigue fracture surfaces in low-carbon steels was observed when the sin 2 ψ method was used for stress measurement. However, the residual stresses became higher with increasing R when these were measured by the proposed method. On the basis of this, the stress intensity factor range, ΔK, can be estimated from the residual stress on the fatigue fracture surface. (author)

Copper Determination in Gunshot Residue by Cyclic Voltammetric and Inductive Coupled Plasma-Optical Emission Spectroscopy

Directory of Open Access Journals (Sweden)

Mohd Hashim Nurul’Afiqah Hashimah

2016-01-01

Full Text Available Analysis of gunshot residue (GSR is a crucial evidences for a forensic analyst in the fastest way. GSR analysis insists a suitable method provides a relatively simple, rapid and precise information on the spot at the crime scene. Therefore, the analysis of Cu(II in GSR using cyclic voltammetry (CV on screen printed carbon electrode (SPCE is a better choice compared to previous alternative methods such as Inductive Coupled Plasma-Optical Emission Spectroscopy (ICP-OES those required a long time for analysis. SPCE is specially designed to handle with microvolumes of sample such as GSR sample. It gives advantages for identification of copper in GSR on-site preliminary test to prevent the sample loss on the process to be analyzed in the laboratory. SPCE was swabbed directly on the shooter’s arm immediately after firing and acetate buffer was dropped on SPCE before CV analysis. For ICP-OES analysis, cotton that had been soaked in 0.5 M nitric acid was swabbed on the shooter’s arm immediately after firing and kept in a tightly closed sampling tube. Gold coated SPCE that had been through nanoparticles modification exhibits excellent performance on voltammograms. The calibration was linear from 1 to 50 ppm of copper, the limit of detection for copper was 0.3 ppm and a relative standard deviation was 6.1 %. The method was successfully applied to the determination of copper in GSR. The Cu determination on SPCE was compared and validated by ICP-OES method with 94 % accuracy.

Shell thinning and reproductive impairment in black ducks after cessation of DDE dosage

Science.gov (United States)

Longcore, J.R.; Stendell, R.C.

1977-01-01

Captive black ducks (anas rubripes) were fed dietary DDE [1,1-dichloro-2,2-bis (p-chlorophenyl)ethylene] at 10 ppm (dry weight; about 2 ppm on a natural diet basis) for 2 breeding seasons, then untreated feed for 2 succeeding years. Residues of DDE in the carcasses of adults declined 90% during the 2-year clean-up period. Following 2 years of dietary DDE, mean residues in eggs reached 64.9 ppm. Even after 2 years on clean feed, DDE residues in the eggs averaged 6.2 ppm or 9.5% of the mean DDE level reached after 2 years on treated feed. Shells of eggs from treated hens were about 20% thinner than shells of eggs from controls. Stoppage of DDE dosage resulted in progressively thicker shells, yet even after 2 years on untreated feed hens laid eggs with shells about 10% thinner than control hens. After DDE was removed from the diet, DDE residues in the eggs decreased, shell thickness increased, and reproductive success improved. Hens previously exposed to DDE, but then fed clean feed for 2 years, still produced significantly fewer surviving ducklings than did control hens.

Determination and speciation of plutonium, americium, uranium, thorium, potassium and 137Cs in a Venice canal sediment sample

International Nuclear Information System (INIS)

Testa, C.; Desideri, D.; Guerra, F.; Meli, M.A.; Roselli, C.; Degetto, S.

1998-01-01

A sequential extraction method consisting of six operationally-defined fractions has been developed for determining the geochemical partitioning of natural (U, Th, 40 K) and anthropogenic (Pu, Am, 137 Cs) radionuclides in a 40-50 cm deep sediment sample collected in a Venice canal. Extraction chromatography was used for the chemical separation of a single radionuclide; the final recoveries were calculated by adding 232 U, 228 Th, 242 Pu and 243 Am as the yield tracers. After electrodeposition the alpha spectrometry was carried out. 137 Cs and 40 K were measured by gamma spectrometry. The total concentrations in the wet sample, obtained by a complete disgregation of the matrix by NaOH fusion, were the following: 239+240 Pu = 610 ± 80 mBq/kg, 238 Pu = 13 ± 5mBq/kg, 241 Am 200 ± 30 mBq/kg, 137 Cs = 6.9 ± 1.1 Bq/kg, U = 1.33 ± 0.14 ppm, Th = 2.69 ± 0.26 ppm, K = 0.72 ± 0.04 %. The mean ratio 238 Pu/ 239+240 Pu ( 0.02) shows a contamination due essentially to fall-out and U and Th alpha spectra indicate the natural origin of two elements. The absence of 134 Cs proves that the sediment was not affected by the Chernobyl fall-out. For the speciation, the following fractions were considered: water soluble, carbonates, Fe-Mn oxides, organic matter, acid soluble, residue. Pu (about 65%) and Am (about 90%) were present predominantly in the carbonate fraction; U was more distributed and about 30% appeared both in the carbonate fraction and in the residue; the majority of Th was present in the residue (about 67%); 40 K was totally present in the residue; and 137 Cs was found mostly in the acid soluble fraction (about 46%) and in the residue (about 40%)

Rigid Residue Scan Simulations Systematically Reveal Residue Entropic Roles in Protein Allostery.

Directory of Open Access Journals (Sweden)

Robert Kalescky

2016-04-01

Full Text Available Intra-protein information is transmitted over distances via allosteric processes. This ubiquitous protein process allows for protein function changes due to ligand binding events. Understanding protein allostery is essential to understanding protein functions. In this study, allostery in the second PDZ domain (PDZ2 in the human PTP1E protein is examined as model system to advance a recently developed rigid residue scan method combining with configurational entropy calculation and principal component analysis. The contributions from individual residues to whole-protein dynamics and allostery were systematically assessed via rigid body simulations of both unbound and ligand-bound states of the protein. The entropic contributions of individual residues to whole-protein dynamics were evaluated based on covariance-based correlation analysis of all simulations. The changes of overall protein entropy when individual residues being held rigid support that the rigidity/flexibility equilibrium in protein structure is governed by the La Châtelier's principle of chemical equilibrium. Key residues of PDZ2 allostery were identified with good agreement with NMR studies of the same protein bound to the same peptide. On the other hand, the change of entropic contribution from each residue upon perturbation revealed intrinsic differences among all the residues. The quasi-harmonic and principal component analyses of simulations without rigid residue perturbation showed a coherent allosteric mode from unbound and bound states, respectively. The projection of simulations with rigid residue perturbation onto coherent allosteric modes demonstrated the intrinsic shifting of ensemble distributions supporting the population-shift theory of protein allostery. Overall, the study presented here provides a robust and systematic approach to estimate the contribution of individual residue internal motion to overall protein dynamics and allostery.

Significance of Lead Residues in Mallard Tissues

Science.gov (United States)

Longcore, J.R.; Locke, L.N.; Bagley, George E.; Andrews, R.

1974-01-01

Tissues of adult, lead-dosed mallards that either died or were sacrificed were analyzed for lead. Lead levels in brains, tibiae, and breast muscle of ducks that died and in tibiae of ducks that were sacrificed increased significantly from dosage until death. Lead in the heart, lung, and blood from sacrificed ducks decreased significantly from dosage until death. Lead concentrations in tissues from ducks in the two groups were not significantly different except for the liver, kidney, and lung. Average lead levels in the livers and kidneys of ducks that died were significantly higher than those in ducks that were sacrificed. The mean concentration of lead in the lungs of the ducks sacrificed was significantly higher than the mean level in the lungs of ducks that died. Measurements of the lead concentrations in this study, when compared with lead levels reported in the literature for avian and non-avian species, showed that arbitrary diagnostic levels indicating lead poisoning could be set. In mallard ducks, lead levels exceeding 3 ppm in the brain, 6 to 20 ppm in the kidney or liver, or 10 ppm in clotted blood from the heart indicated acute exposure to lead.

Evaluation of pesticide residue dynamics in Chinese cabbage, head cabbage and cauliflower.

Science.gov (United States)

Kocourek, František; Stará, Jitka; Holý, Kamil; Horská, Tereza; Kocourek, Vladimír; Kováčová, Jana; Kohoutková, Jana; Suchanová, Marie; Hajšlová, Jana

2017-06-01

Pesticide residues from the time of application until harvest were analysed for 20, 17 and 18 active insecticidal and fungicidal substances in Chinese cabbage, head cabbage and cauliflower, respectively. In total, 40 mathematical models of residue degradation were developed using a first-order kinetic equation, and from these models it was possible to forecast the action pre-harvest interval for a given action threshold for low-residue production in Brassica vegetables as a percentage of the maximum residue level. Additionally, it was possible to establish an action pre-harvest interval based on an action threshold of 0.01 mg kg ‒1 for the production of Brassica vegetables for baby food. Among the evaluated commodities, the speed of residue degradation was highest in head cabbage, medium in Chinese cabbage and lowest in cauliflower. The half-lives of pesticide in various vegetables were also determined: they ranged from 1.55 to 5.25 days in Chinese cabbage, from 0.47 to 6.54 days in head cabbage and from 1.88 to 7.22 days in cauliflower.

NOVEL ZINC OXIDE FUNCTIONALIZED CARBON NANOTUBE CHEMIRESISTOR SENSOR ENHANCED WITH SURFACE O2 PLASMA INDUCED DEFECTS FOR METHANEDETECTION AT SINGLE PPM LEVEL

Science.gov (United States)

Novelty/Progress ClaimsThis paper presents a novel functionalized multi-walled carbon nanotubes (MWCNTs) based chemiresistor sensor which can detect methane at 2 ppm concentration level at room temperature with relative resistance change (RRC) of 2%. This is the highest reported ...

Intake of Fruits and Vegetables with Low-to-Moderate Pesticide Residues Is Positively Associated with Semen-Quality Parameters among Young Healthy Men123

Science.gov (United States)

Gaskins, Audrey J; Williams, Paige L; Mendiola, Jaime; Levine, Hagai; Hauser, Russ; Swan, Shanna H; Chavarro, Jorge E

2016-01-01

Background: Numerous studies have shown that occupational or environmental pesticide exposure can affect male fertility. There is less evidence, however, regarding any potentially adverse effects of pesticide residues in foods on markers of male fertility potential. Objectives: We examined the relations between fruit and vegetable intake, considering pesticide residue status, and semen quality and serum concentrations of reproductive hormones in healthy young men. Methods: The Rochester Young Men's Study is a cross-sectional study that recruited men aged 18–22 y (n = 189) in Rochester, New York. Participants completed a questionnaire, provided a semen sample, had a blood sample drawn, and underwent a physical examination at enrollment. Semen samples were analyzed for total sperm count, sperm concentration, morphology, motility, ejaculate volume, total motile count, and total normal count. Dietary intake during the previous year was assessed by a validated food-frequency questionnaire. Fruit and vegetables were categorized as having high [Pesticide Residue Burden Score (PRBS) ≥4] or low-to-moderate (PRBS vegetable intake with semen variables and reproductive hormones while adjusting for potential confounding factors. Results: The total intake of fruit and vegetables was unrelated to semen quality. However, the intake of fruit and vegetables with low-to-moderate pesticide residues was associated with a higher total sperm count and sperm concentration, whereas the intake of fruit and vegetables with high pesticide residues was unrelated to semen quality. On average, men in the highest quartile of low-to-moderate-pesticide fruit and vegetable intake (≥2.8 servings/d) had a 169% (95% CI: 45%, 400%) higher total sperm count and a 173% (95% CI: 57%, 375%) higher sperm concentration than did men in the lowest quartile (vegetables, regardless of pesticide-residue status, was not associated with reproductive hormone concentrations. Conclusions: The consumption of fruit

Development of Analytical Method and Monitoring of Veterinary Drug Residues in Korean Animal Products.

Science.gov (United States)

Song, Jae-Sang; Park, Su-Jeong; Choi, Jung-Yun; Kim, Jin-Sook; Kang, Myung-Hee; Choi, Bo-Kyung; Hur, Sun Jin

2016-01-01

This study was conducted to determine the residual amount of veterinary drugs such as meloxicam, flunixin, and tulathromycin in animal products (beef, pork, horsemeat, and milk). Veterinary drugs have been widely used in the rearing of livestock to prevent and treat diseases. A total of 152 samples were purchased from markets located in major Korean cities (Seoul, Busan, Incheon, Daegu, Daejeon, Gwangju, Ulsan and Jeju), including Jeju. Veterinary drugs were analyzed by liquid chromatography-tandem mass spectrometry according to the Korean Food Standards Code. The resulting data, which are located within 70-120% of recovery range and less than 20% of relative standard deviations, are in compliance with the criteria of CODEX. A total of five veterinary drugs were detected in 152 samples, giving a detection rate of approximately 3.3%; and no food source violated the guideline values. Our result indicated that most of the veterinary drug residues in animal products were below the maximum residue limits specified in Korea.

Qualidade de tubérculos de batatas-semente tratados com paraquat e o desenvolvimento de uma metodologia simplificada de detecção de resíduo do herbicida Quality of seed potato tubers treated with paraquat and the development of a simplified methodology for paraquat residue detection

Directory of Open Access Journals (Sweden)

Welington Pereira

1995-01-01

concentração do produto aumenta. A metodologia simplificada desenvolvida permitiu detectar resíduos de paraquat ao nível de 0,06 ppm, indicando uma excelente aproximação, pois, o limite de tolerância do paraquat em tubérculos de batata é de 0,2 ppm, normalmente, determinado pelo método analítico completo, que apresenta limites de detecção em torno de 0,01 ppm e recuperação acima de 70%. Uma avaliação qualitativa da concentração residual de produto nas amostras foi possível através de leitura e comparações visuais entre os diferentes graus de cores desenvolvidas nas soluções visuais entre os diferentes graus de cores desenvolvidas nas soluções padrão e a cor desenvolvida na amostra, não necessitando, portanto, das leituras colorimétricas, podendo ser feita inclusive no campo. Observou-se que a maioria do paraquat permaneceu na região de casca até o período de 4 semanas após a aplicação do paraquat.Seed potatoes tubers (Solanum tuberosum of two cultivars (Achat and Baronesa were treated with paraquat solutions to evalute the internal tuber quality and to detect its residue by a simplified methodology. Two experiments were carried out at the National Research Center on Vegetables, Brasília, DF. In experiment one some tubers were immersed in 0 and 200 ppm of paraquat solutions and others were injected with 0,5 ml of 0 and 200 ppm solutions of the herbicide. Twelve tubers were used as plot in a complete randomized design with 8 replications. The internal tuber quality was evaluated after breaking dormancy and sprouting of ten tubers. Also, two tubers were sampled and put in 5 liter pots and grown under greenhouse conditions to observe if the herbicide would affect the growth of the new plant generation. The immersion treatments did not cause any internal damage to the tubers nor did they affect the new plant generation; however, tubers injected with paraquat were severely damaged (carbonization. Also, the next plant generation was affected

Determine metrics and set targets for soil quality on agriculture residue and energy crop pathways

Energy Technology Data Exchange (ETDEWEB)

Ian Bonner; David Muth

2013-09-01

There are three objectives for this project: 1) support OBP in meeting MYPP stated performance goals for the Sustainability Platform, 2) develop integrated feedstock production system designs that increase total productivity of the land, decrease delivered feedstock cost to the conversion facilities, and increase environmental performance of the production system, and 3) deliver to the bioenergy community robust datasets and flexible analysis tools for establishing sustainable and viable use of agricultural residues and dedicated energy crops. The key project outcome to date has been the development and deployment of a sustainable agricultural residue removal decision support framework. The modeling framework has been used to produce a revised national assessment of sustainable residue removal potential. The national assessment datasets are being used to update national resource assessment supply curves using POLYSIS. The residue removal modeling framework has also been enhanced to support high fidelity sub-field scale sustainable removal analyses. The framework has been deployed through a web application and a mobile application. The mobile application is being used extensively in the field with industry, research, and USDA NRCS partners to support and validate sustainable residue removal decisions. The results detailed in this report have set targets for increasing soil sustainability by focusing on primary soil quality indicators (total organic carbon and erosion) in two agricultural residue management pathways and a dedicated energy crop pathway. The two residue pathway targets were set to, 1) increase residue removal by 50% while maintaining soil quality, and 2) increase soil quality by 5% as measured by Soil Management Assessment Framework indicators. The energy crop pathway was set to increase soil quality by 10% using these same indicators. To demonstrate the feasibility and impact of each of these targets, seven case studies spanning the US are presented

Energy dependence of fusion evaporation-residue cross sections in the 28Si+28Si reaction

International Nuclear Information System (INIS)

Vineyard, M.F.; Bauer, J.S.; Gosdin, C.H.; Trotter, R.S.; Kovar, D.G.; Beck, C.; Henderson, D.J.; Janssens, R.V.F.; Wilkins, B.D.; Rosner, G.; Chowdhury, P.; Ikezoe, H.; Kuhn, W.; Kolata, J.J.; Hinnefeld, J.D.; Maguire, C.F.; Mateja, J.F.; Prosser, F.W.; Stephans, G.S.F.

1990-01-01

Velocity distributions of mass-identified evaporation residues produced in the 28 Si+ 28 Si reaction have been measured at bombarding energies of 174, 215, 240, 309, 397, and 452 MeV using time-of-flight techniques. These distributions were used to identify evaporation residues and to separate the complete-fusion and incomplete-fusion components. Angular distributions and total cross sections were extracted at all six bombarding energies. The complete-fusion evaporation-residue cross sections and the deduced critical angular momenta are compared with lower energy data and the predictions of existing models

76 FR 17374 - Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2011-03-29

... ppm; olive at 0.35 ppm; avocado; and fruit crops, including: Black sapote; canistel; mamey sapote... or processed agricultural commodities rice, grain at 0.25 ppm; rice, hulls at 1.0 ppm; alfalfa... on these crops. Bayer CropScience is also proposing that the above proposed tolerances on rice, based...

A proton nuclear magnetic resonance investigation of proximal histidyl residues in human normal and abnormal hemoglobins: a probe for the heme pocket

International Nuclear Information System (INIS)

Takahashi, S.; Lin, A.K.L.; Ho, C.

1982-01-01

Proton nuclear magnetic resonance spectroscopy at 250 MHz has been used to investigate the conformations of proximal histidyl residues of human normal adult hemoglobin, hemoglobin Kempsey [K145(HC2) Tyr #betta# Asp], and hemoglobin McKees Rocks [K145(HC2) Tyr #betta# Term] around neutral pH in H 2 O at 27 0 C, all in the deoxy form. Two resonances that occur between 58 and 76 ppm downfield from the water proton signal have been assigned to the hyperfine shifted proximal histidyl NH-exchangeable protons of the J and K-chains of deoxyhemoglobin. These two resonances are sensitive to the quaternary state of hemoglobin, amino acid substitutions in the J 1 K 2 -subunit interface and in the carboxy-terminal region of the K-chain, and the addition of organic phosphates. The experimental results show that there are differences in the heme pockets among these four hemoglobins studied. The structural and dynamic information derived from the hyperfine shifted proximal histidyl NH-exchangeable proton resonances complement that obtained from the ferrous hyperfine shifted and exchangeable proton resonances of deoxyhemoglobin over the spectral region from 5 to 20 ppm downfield from H 2 O. The relationship between these findings and Perutz's stereochemical mechanism for the cooperative oxygenation of hemoglobin is discussed

Prevalence, Predictors and Clinical Outcome of Residual Pulmonary Hypertension Following Tricuspid Annuloplasty.

Science.gov (United States)

Chen, Yan; Liu, Ju-Hua; Chan, Daniel; Sit, Ko-Yung; Wong, Chun-Ka; Ho, Kar-Lai; Ho, Lai-Ming; Zhen, Zhe; Lam, Yui-Ming; Lau, Chu-Pak; Au, Wing-Kok; Tse, Hung-Fat; Yiu, Kai-Hang

2016-07-22

Tricuspid annuloplasty is increasingly performed during left heart valve surgery, but the long-term clinical outcome postoperatively is not satisfactory. The aim of this study was to determine whether residual pulmonary hypertension (PHT) contributes to the adverse outcome. One-hundred thirty-seven patients (age 61±11 years; men, 30%) who underwent tricuspid annuloplasty during left-side valve surgery were enrolled. The mean pulmonary artery systolic pressure before surgery was 49±13 mm Hg and 32±15 mm Hg following surgery. Patients were divided into 3 groups according to postoperative pulmonary artery systolic pressure: no residual PHT (n=78, 57%), mild residual PHT (n=43, 31%), or significant residual PHT (n=16, 12%). A preoperative larger right ventricular (RV) geometry and tricuspid valve tethering area were associated with mild or significant residual PHT. A total of 24 adverse events (20 heart failures and 4 cardiovascular deaths) occurred during a median follow-up of 25 months. Kaplan-Meier survival curve demonstrated that patients with significant residual PHT had the highest percentage of adverse events followed by those with mild residual PHT. Patients with no residual PHT had a very low risk of adverse events. Multivariable Cox regression analysis revealed that both mild (hazard ratio=4.94; 95% CI =1.34-18.16; P=0.02) and significant residual PHT (hazard ratio=8.67; 95% CI =2.43-30.98; P<0.01) were independent factors associated with adverse events. The present study demonstrated that 43% of patients who underwent tricuspid annuloplasty had residual PHT. The presence of mild or significant residual PHT was associated with adverse events in these patients. © 2016 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley Blackwell.

Bioactive compounds and antioxidant potential for polyphenol-rich cocoa extract obtained by agroindustrial residue.

Science.gov (United States)

Gabbay Alves, Taís Vanessa; Silva da Costa, Russany; Aliakbarian, Bahar; Casazza, Alessandro Alberto; Perego, Patrizia; Pinheiro Arruda, Mara Silvia; Carréra Silva Júnior, José Otávio; Converti, Attilio; Ribeiro Costa, Roseane Maria

2017-11-10

Processing of cocoa (Theobroma cacao L.) beans responsible for agricultural exports leads to large amounts of solid waste that were discarded, however, this one presents high contents of metabolites with biological activities. The major objective of this study was to valorise cocoa agroindustrial residue obtained by hydraulic pressing for extract rich in antioxidants. For it, the centesimal composition of residue was investigated, the green extraction was carried out from the residue after, the bioactive compounds, sugar contents and screaming by HPTLC were quantified for extract. The extract has a total polyphenol content of 229.64 mg/g and high antioxidant activity according to ABTS 225.0 μM/g. HTPLC analysis confirmed the presence in the extract, residue of terpenes, sesquiterpenes, flavonoids and antioxidant activity. These results, as a whole, suggest that the extract from the cocoa residue has interesting characteristics to alternative crops with potential industrial uses.

Residual gas analysis

International Nuclear Information System (INIS)

Berecz, I.

1982-01-01

Determination of the residual gas composition in vacuum systems by a special mass spectrometric method was presented. The quadrupole mass spectrometer (QMS) and its application in thin film technology was discussed. Results, partial pressure versus time curves as well as the line spectra of the residual gases in case of the vaporization of a Ti-Pd-Au alloy were demonstrated together with the possible construction schemes of QMS residual gas analysers. (Sz.J.)

40 CFR 80.530 - Under what conditions can 500 ppm motor vehicle diesel fuel be produced or imported after May 31...

Science.gov (United States)

2010-07-01

... motor vehicle diesel fuel be produced or imported after May 31, 2006? 80.530 Section 80.530 Protection... FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Temporary Compliance Option § 80.530 Under what conditions can 500 ppm motor vehicle diesel...

Assessing the Availability of Wood Residues and Residue Markets in Virginia

OpenAIRE

Alderman, Delton R. Jr.

1998-01-01

A statewide mail survey of primary and secondary wood product manufacturers was undertaken to quantify the production and consumption of wood residues in Virginia. Two hundred and sixty-six wood product manufacturers responded to the study and they provided information on the production, consumption, markets, income or disposal costs, and disposal methods of wood residues. Hardwood and pine sawmills produce approximately 66 percent of Virginia's wood residues. Virginia's wood product man...

77 FR 30481 - Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2012-05-23

... available for enforcement purposes. Contact: Thomas Harris, (703) 308-9423, email address: harris.thomas@epa... poultry, meat at 0.01 ppm; poultry, fat at 0.01 ppm; poultry, liver at 0.2 ppm; egg at 0.1 ppm; cattle..., poultry and eggs which also underwent successful independent laboratory validations. Contact: Erin Malone...

Accumulation of {sup 14}C-trinitrotoluene and related nonextractable (bound) residues in Eisenia fetida

Energy Technology Data Exchange (ETDEWEB)

Belden, Jason B., E-mail: jbelden@okstate.edu [Department of Zoology, Oklahoma State University, Stillwater, OK 74078 (United States); Lotufo, Guillerme R. [US Army Engineer Research and Development Center, Vicksburg, MS 39180 (United States); Chambliss, C. Kevin [Department of Chemistry, Baylor University, Waco, TX 76798 (United States); Fisher, Jonathan C. [Department of Zoology, Oklahoma State University, Stillwater, OK 74078 (United States); Johnson, Dave R.; Boyd, Robert E.; Sims, Jerre G. [US Army Engineer Research and Development Center, Vicksburg, MS 39180 (United States)

2011-05-15

To determine if trinitrotoluene (TNT) forms nonextractable residues in earthworms and to measure the relative degree of accumulation as compared to TNT and its deaminated metabolites, Eisenia fetida was exposed to {sup 14}C-TNT using dermal contact to filter paper or exposure to soil. Nonextractable residues made up 32-68% of total body burden depending on exposure media and depuration time. Parent TNT accounted for less than 3% of radioactivity, while ADNTs accounted for 7-38%. Elimination half-lives were 61-120 h for TNT, ADNTs, and DANTs, which was significantly lower than the half-lives found for nonextractable residues, 201-240 h. However, over 80% of the nonextractable residue was solubilized using weak acid (pH 2). Based on our findings that TNT accumulation occurs primarily as nonextractable residues, which have a longer half-life, and that nonextractable residues can be solubilized, we propose that nonextractable residues could be used as a selective biomarker for assessing TNT contamination. - Highlights: > Trinitrotoluene accumulation in earthworms primarily occurs as nonextractable residues. > Nonextractable residues have a significantly longer half life in the worm as compared to TNT and its solvent-extractable deaminated metabolites. > Nonextractable residue may be useful as a biomarker for exposure to TNT. - The majority of trinitrotoluene accumulation in earthworms occurs as nonextractable residues that have a significantly longer half life in the worm as compared to TNT and its solvent-extractable deaminated metabolites.

Contaminação por compostos organoclorados em salsichas hot-dog comercializadas na cidade de Santa Maria (RS, Brasil Contamination for organochlorine compounds in hot-dog sausages, commercialized in the city of Santa Maria (RS, Brazil

Directory of Open Access Journals (Sweden)

Stanislau Bogusz Junior

2004-10-01

Full Text Available Com o objetivo de monitorar os resíduos de compostos tóxicos em alimentos, verificou-se a freqüência e os níveis de praguicidas organoclorados (OC e bifenilas policloradas (PCBs em amostras de salsichas Hot-Dog, comercializadas na Cidade de Santa Maria, Estado do Rio Grande do Sul (RS e, compararam-se os valores com aqueles estabelecidos pela Legislação. Para as análises, procedeu-se a extração da gordura das amostras. A partir da purificação desta, obteve-se um extrato do qual se determinaram os resíduos organoclorados por cromatografia gasosa com detector de captura eletrônica (CG - µECD63Ni. Verificou-se que o lindano e o HCB foram os pesticidas que apresentaram as maiores concentrações médias (0,001798ppm e 0,001652ppm, respectivamente. O somatório dos níveis médios dos pesticidas organoclorados detectados foi de 0,015783ppm, sendo que deste total 0,011165ppm pertencia aos metabólitos do DDT. Quanto as bifenilas policloradas, as maiores concentrações médias corresponderam às PCBs 10 (0,001817ppm e 28 (0,000317ppm. O somatório das PCBs foi de 0,002172ppm. As concentrações de praguicidas organoclorados e PCBs encontradas nas amostras analisadas estavam abaixo dos limites máximos permitidos pela legislação.With the objective of monitoring toxic compounds residues in food, the frequency and levels of organochlorine pesticides and polychlorinated biphenyls were verified in sausage samples, hot dog type, commercialized in the city of Santa Maria (RS, Brazil. Values were compared with the ones established by Brazilian legislation. For the analyses the extraction of fat from the samples was done. From the purification of the fat, there was acquisition of an extract in which was determined the organochlorine contaminants residues by gas chromatography with electronic capture detector (CG - µECD63Ni. It was learned that the lindane and HCB were the pesticides that presented the biggest concentration averages (0

Nitrogen mineralization from selected 15N-labelled crop residues and humus as affected by inorganic nitrogen

International Nuclear Information System (INIS)

Santos, J.A.

1987-01-01

The use of cover crops or crop residues as a source of N to succeeding crops has become a matter of increasing importance for economic and environmental reason. Greenhouse and field studies were conducted to determine the N contribution of four 15 N labelled crop residues, rye (Secale cereale L.), wheat (Triticum aestivum L.), crimson clover (Trifolium encarnatum L.), and hairy vetch (Vicia sativa L.), to successive crops and to evaluate the effect of different organic (ON) and inorganic N (IN) combinations on mineralization of the above residues. Total 15 N recovery from the residues ranged from 51% to 85% and 4% to 74% for the greenhouse and field studies, respectively

76 FR 76674 - Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2011-12-08

... purified by solid phase extraction (graphitized carbon black for alfalfa, snap bean pods with seed, and... rice): grain, cereal at 0.01 ppm; grain, cereal, forage at 0.05 ppm; grain, cereal, hay at 0.05 ppm..., except rice; forage at 8.0 ppm; grain, cereal, forage, fodder and straw, group 16, except rice; hay...

Crop residue recycling for economic and environmental sustainability: The case of India

Directory of Open Access Journals (Sweden)

Devi Saroj

2017-09-01

Full Text Available India is one of the key producers of food grain, oilseed, sugarcane and other agricultural products. Agricultural crops generate considerable amounts of leftover residues, with increases in food production crop residues also increasing. These leftover residues exhibit not only resource loss but also a missed opportunity to improve a farmer’s income. The use of crop residues in various fields are being explored by researchers across the world in areas such as textile composite non-woven making processes, power generation, biogas production, animal feed, compost and manures, etc. The increasing trend in addition of bio-energy cogeneration plants, increasing demand for animal feedstock and increasing trend for organic agriculture indicates a competitive opportunity forcrop residue in Agriculture. It is to be noted that the use of this left over residue isoften not mutually exclusive which makes measurement of its economic value more difficult.For example, straw can be used as animal bedding and thereafter as a crop fertilizer. In view of this, the main aim of this paper envisaged to know about how much crop residue is left unutilized and how best they can be utilized for alternative purposes for environmental stewardship and sustainability. In this context, an attempt has been made to estimate the total crop residue across the states and its economic value though data available from various government sources and a SWOT analysis performed for possible alternative uses of residue in India. This paper also discusses the successful case studies of India and global level of use of crop residues in economic activities. Over all 516 Mtonnes of crop residue was produced in 2014-15 in India among which cereals were the largest producer of crop residue followed by sugarcane. The energy potential from paddy rice straw crop residue was estimated as 486,955 megawatt for 2014-15 and similarly for coarse cereals it was 226,200megawatt.

Mutational properties of amino acid residues: implications for evolvability of phosphorylatable residues

DEFF Research Database (Denmark)

Creixell, Pau; Schoof, Erwin M.; Tan, Chris Soon Heng

2012-01-01

in terms of their mutational activity. Moreover, we highlight the importance of the genetic code and physico-chemical properties of the amino acid residues as likely causes of these inequalities and uncover serine as a mutational hot spot. Finally, we explore the consequences that these different......; it is typically assumed that all amino acid residues are equally likely to mutate or to result from a mutation. Here, by reconstructing ancestral sequences and computing mutational probabilities for all the amino acid residues, we refute this assumption and show extensive inequalities between different residues...... mutational properties have on phosphorylation site evolution, showing that a higher degree of evolvability exists for phosphorylated threonine and, to a lesser extent, serine in comparison with tyrosine residues. As exemplified by the suppression of serine's mutational activity in phosphorylation sites, our...

Application of laser interferometry for assessment of surface residual stress by determination of stress-free state

International Nuclear Information System (INIS)

Kim, Dong Won; Kwon, Dong Il; Lee, Nak Kyu; Choi, Tae Hoon; Na, Kyoung Hoan

2003-01-01

The total relaxed stress in annealing and the thermal strain/stress were obtained from the identification of the residual stress-free state using Electronic Speckle Pattern Interferometry (ESPI). The residual stress fields in case of both single and film/substrate systems were modeled using the thermo-elastic theory and the relationship between relaxed stresses and displacements. We mapped the surface residual stress fields on the indented bulk Cu and the 0.5 μm Au film by ESPI. In indented Cu, the normal and shear residual stress are distributed over -1.7 GPa to 700 MPa and -800 GPa to 600 MPa respectively around the indented point and in deposited Au film on Si wafer, the tensile residual stress is uniformly distributed on the Au film from 500 MPa to 800 MPa. Also we measured the residual stress by the X-Ray Diffractometer (XRD) for the verification of above residual stress results by ESPI

Heat transfer properties of organic coolants containing high boiling residues

International Nuclear Information System (INIS)

Debbage, A.G.; Driver, M.; Waller, P.R.

1964-01-01

Heat transfer measurements were made in forced convection with Santowax R, mixtures of Santowax R and pyrolytic high boiling residue, mixtures of Santowax R and CMRE Radiolytic high boiling residue, and OMRE coolant, in the range of Reynolds number 10 4 to 10 5 . The data was correlated with the equation Nu = 0.015 Re b 0.85 Pr b 0.4 with an r.m.s. error of ± 8.5%. The total maximum error arising from the experimental method and inherent errors in the physical property data has been estimated to be less than ± 8.5%. From the correlation and physical property data, the decrease in heat transfer coefficient with increasing high boiling residue concentration has been determined. It has been shown that subcooled boiling in organic coolants containing high boiling residues is a complex phenomenon and the advantages to be gained by operating a reactor in this region may be marginal. Gas bearing pumps used initially in these experiments were found to be unsuitable; a re-designed ball bearing system lubricated with a terphenyl mixture was found to operate successfully. (author)

Manufacturing of concrete with residues from iron ore exploitation using the technology of radioactive waste cementation

Energy Technology Data Exchange (ETDEWEB)

Versieux, Juniara L.; Lameiras, Fernando S.; Tello, Cledola Cassia Oliveira de, E-mail: juniarani@gmail.com, E-mail: fsl@cdtn.br, E-mail: tellocc@cdtn.br [Centro de Desenvolvimento da Tecnologia Nucelar (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2015-07-01

Radioactive wastes from various segments of economy are immobilized by cementation, because of availability and widespread use in civil construction of cement. New cementitious materials are developed in CDTN using mining residues based on cementing techniques of radioactive wastes. Special procedures were developed to obtain concrete with the use of super plasticizers in which natural sand was totally replaced by mining residues. The motivation for this research is the exploration of banded iron formations (BIF) as iron ore in 'Quadrilatero Ferrifero' of Minas Gerais, where huge amounts of residues are generated with great concern about the environmental sustainability and safety of dams for residue storage. The exploitation of river sand causes many negative impacts, which leads to interest in its replacement by another raw material in mortar and concrete manufacturing. The use of BIF mining residues were studied for manufacturing of concrete pavers to contribute to reducing the impact caused by extraction of natural sand and use of mining residues. Previously developed procedures with total replacement of natural sand for mining residues were modified, including use of gravel to obtain pavers with improved properties. Four different mixtures were tested, in which the proportion of gravel and super plasticizer was varied. Monitored properties of pavers, among others, were compression resistance, water absorption, and void volume. With addition of gravel, the pavers had higher void index than those made only with mortar, and higher resistance to compression after 28 days of curing (an average of 18MPa of those made with mortar to 24MPa of those made with concrete). (author)

Manufacturing of concrete with residues from iron ore exploitation using the technology of radioactive waste cementation

International Nuclear Information System (INIS)

Versieux, Juniara L.; Lameiras, Fernando S.; Tello, Cledola Cassia Oliveira de

2015-01-01

Radioactive wastes from various segments of economy are immobilized by cementation, because of availability and widespread use in civil construction of cement. New cementitious materials are developed in CDTN using mining residues based on cementing techniques of radioactive wastes. Special procedures were developed to obtain concrete with the use of super plasticizers in which natural sand was totally replaced by mining residues. The motivation for this research is the exploration of banded iron formations (BIF) as iron ore in 'Quadrilatero Ferrifero' of Minas Gerais, where huge amounts of residues are generated with great concern about the environmental sustainability and safety of dams for residue storage. The exploitation of river sand causes many negative impacts, which leads to interest in its replacement by another raw material in mortar and concrete manufacturing. The use of BIF mining residues were studied for manufacturing of concrete pavers to contribute to reducing the impact caused by extraction of natural sand and use of mining residues. Previously developed procedures with total replacement of natural sand for mining residues were modified, including use of gravel to obtain pavers with improved properties. Four different mixtures were tested, in which the proportion of gravel and super plasticizer was varied. Monitored properties of pavers, among others, were compression resistance, water absorption, and void volume. With addition of gravel, the pavers had higher void index than those made only with mortar, and higher resistance to compression after 28 days of curing (an average of 18MPa of those made with mortar to 24MPa of those made with concrete). (author)

Fate of 14C-Chlorpyrifos Insecticide in Sunflower Seeds and Oil and the Effect of Processing According to Industrial Practice

International Nuclear Information System (INIS)

Abdel-Gawad, H.; Khatab, M.S.; Hegazi, B.

2007-01-01

Ethyl -1- 14 C-chlorpyrifos and some of its degradation products have been prepared for the present investigation. Sunflower plants were treated with 14 C-chlorpyrifos under conditions simulating local agricultural practice. 14 C-residue in seeds were determined at different time intervals. At harvest time about 8 % of 14 C-activity was associated with oil. The methanol soluble 14 C-residues accounted for 0.8 % of the total seed residues, while the cake contained about 80 % of the total residues. About 46 % of the 14 C-activity in the crude oil could be eliminated by simulated commercial processes locally used for oil refining. The refined oil had a 14 C- residue level of about 21 ppm. Chromatographic analysis of crude and refined oil revealed the presence of the parent compound together with three metabolites which were identified as chlorpyrifos oxon, desethyl chlorpyrifos, and desethyl chlorpyrifos oxon in addition to an unknown compound. Methanol extract of the cake revealed the presence of the parent compound and its oxon as free compounds. Acid hydrolysis of the conjugated metabolites in the methanol extract yielded desethyl chlorpyrifos and 3, 5, 6- trichloro-2-hydroxypyridine

Minimum TI4085D interlock setpoint at 1.0 GPM sludge-only feed rate and 14,000 ppm TOC

International Nuclear Information System (INIS)

Choi, A.S.

1996-01-01

DWPF-Engineering requested that SRTC determine the minimum indicated melter vapor space temperature that must be maintained in order to minimize the potential for off-gas flammability during a steady sludge-only feeding operation at 1.0 GPM containing 14,000 ppm total organic carbon. The detailed scope of this request is described in the technical task request, HLW-DWPF-TTR-960092 (DWPT Activity No. DWPT-96-0065). In response to this request, a dynamic simulation study was conducted in which the concentration of flammable gases was tracked throughout the course of a simulated 3X off-gas surge using the melter off-gas (MOG) dynamics model. The results of simulation showed that as long as the melter vapor space temperature as indicated on TI4085D is kept at 570 degrees C or higher, the peak concentration of combustible gases in the melter off-gas system is not likely to exceed 60 percent of the lower flammability limit (LFL). The minimum TI4085D of 570 degrees C is valid only when the air purges to FIC3221A and FIC3221B are maintained at or above 850 and 250 lb/hr, respectively. All the key bases and assumptions along with the input data used in the simulation are described in the attached E-7 calculation note

Evaluation of residue-residue contact prediction in CASP10

KAUST Repository

Monastyrskyy, Bohdan

2013-08-31

We present the results of the assessment of the intramolecular residue-residue contact predictions from 26 prediction groups participating in the 10th round of the CASP experiment. The most recently developed direct coupling analysis methods did not take part in the experiment likely because they require a very deep sequence alignment not available for any of the 114 CASP10 targets. The performance of contact prediction methods was evaluated with the measures used in previous CASPs (i.e., prediction accuracy and the difference between the distribution of the predicted contacts and that of all pairs of residues in the target protein), as well as new measures, such as the Matthews correlation coefficient, the area under the precision-recall curve and the ranks of the first correctly and incorrectly predicted contact. We also evaluated the ability to detect interdomain contacts and tested whether the difficulty of predicting contacts depends upon the protein length and the depth of the family sequence alignment. The analyses were carried out on the target domains for which structural homologs did not exist or were difficult to identify. The evaluation was performed for all types of contacts (short, medium, and long-range), with emphasis placed on long-range contacts, i.e. those involving residues separated by at least 24 residues along the sequence. The assessment suggests that the best CASP10 contact prediction methods perform at approximately the same level, and comparably to those participating in CASP9.

Sand fly control in Kenya with residual pesticide application on HESCO barriers

Science.gov (United States)

US military operations in hot-arid regions still face significant impacts from mosquito and sand fly vectors of diseases. Personal protective measures (PPM) such as DEET or treated bed nets and clothing can reduce contact with disease vectors and nuisance insects; however, irregular use of PPM coupl...

Analysis of residual swirl in tangentially-fired natural gas-boiler

International Nuclear Information System (INIS)

Hasril Hasini; Muhammad Azlan Muad; Mohd Zamri Yusoff; Norshah Hafeez Shuaib

2010-01-01

This paper describes the investigation on residual swirl flow in a 120 MW natural gas, full-scale, tangential-fired boiler. Emphasis is given towards the understanding of the behavior of the combustion gas flow pattern and temperature distribution as a result of the tangential firing system of the boiler. The analysis was carried out based on three-dimensional computational modeling on full scale boiler with validation from key design parameter as well as practical observation. Actual operating parameters of the actual boiler are taken as the boundary conditions for this modeling. The prediction of total heat flux was found to be in agreement with the key design parameter while the residual swirl predicted at the upper furnace agrees qualitatively with the practical observation. Based on this comparison, detail analysis was carried out for comprehensive understanding on the generation and destruction of the residual swirl behavior in boiler especially those with high capacity. (author)

Proceedings of the 7. biennial residue-to-revenue residual wood conference 2007

International Nuclear Information System (INIS)

Raulin, J.

2007-01-01

This conference provided information on the highest and best use of residual wood, which is quickly becoming a valuable commodity. Issues concerning forest residues, sawmill wastes, agricultural residues and urban organic materials were discussed along with trends in Canadian surplus mill waste production. The evolving nature and technologies of the biomass business were highlighted with particular focus on how to generate energy and save money through the use of residual wood. Residual wood energy projects and developments in Canada, North America and Europe were outlined along with biomass development in relation to forest fires and insect disturbances. Cogeneration technologies using wood wastes for thermal heat, steam and electricity were also presented, along with transportation fuel technologies for the production of ethanol. It was noted that with the rising cost of energy, the forest industry is seeking energy solutions based on the use of residual wood. The range of economically practical residual wood solutions continues to grow as energy prices increase. The conference was attended by more than 200 delegates from the forest industry, suppliers and government representatives, to discuss policies and procedures currently in place. Industry investment is being stimulated by the potential for biofuels and biochemicals, as well as the co-operation between the forest and energy sectors. The conference featured 23 presentations, of which 12 have been catalogued separately for inclusion in this database. refs., tabs., figs

Safe apples for baby-food production: survey of pesticide treatment regimes leaving minimum residues.

Science.gov (United States)

Ticha, Jana; Hajslova, Jana; Kovalczuk, Tomas; Jech, Martin; Honzicek, Jiri; Kocourek, Vladimir; Lansky, Miroslav; Kloutvorova, Jana; Falta, Vladan

2007-06-01

A total of 19 pesticide preparations were used according to agricultural practice in six trials in apple orchards. Using gas chromatography-mass spectrometry (GC-MS) and liquid chromatography-tandem mass spectrometry (LC-MS/MS), premature Golden Delicious apples collected 64, 50, 36 days before harvest and mature fruit were examined for residues of active ingredients. No residues of triflumuron, triazamate, chlorpyrifos, etofenprox, fenoxycarb, kresoxim-methyl, cyprodinyl, difenoconazole or thiram were detected in the first sampling. Also, the levels of chlorpyrifos-methyl, penconazole, tebuconazole and tolylfluanid dropped during the pre-harvest interval. Detectable residues of pyridaben, thiacloprid, trifloxystrobin and tetraconazole in harvested fruits were below 0.01 mg kg(-1), which is the maximum concentration of residues acceptable by baby-food producers in any raw material. The only residues exceeding this concentration were captan and teflubenzuron. Based on the data, farmers can choose pesticides for optimal treatment of plants, while enabling growth of a safe crop suitable for baby-food production.

Thermogravimetric investigation of the co-combustion between the pyrolysis oil distillation residue and lignite.

Science.gov (United States)

Li, Hao; Xia, Shuqian; Ma, Peisheng

2016-10-01

Co-combustion of lignite with distillation residue derived from rice straw pyrolysis oil was investigated by non-isothermal thermogravimetric analysis (TGA). The addition of distillation residue improved the reactivity and combustion efficiency of lignite, such as increasing the weight loss rate at peak temperature and decreasing the burnout temperature and the total burnout. With increasing distillation residue content in the blended fuels, the synergistic interactions between distillation residue and lignite firstly increased and then decreased during co-combustion stage. Results of XRF, FTIR, (13)C NMR and SEM analysis indicated that chemical structure, mineral components and morphology of samples have great influence on the synergistic interactions. The combustion mechanisms and kinetic parameters were calculated by the Coats Redfern model, suggesting that the lowest apparent activation energy (120.19kJ/mol) for the blended fuels was obtained by blending 60wt.% distillation residue during main co-combustion stage. Copyright © 2016 Elsevier Ltd. All rights reserved.

Application of Highly Purified Electrolyzed Chlorine Dioxide for Tilapia Fillet Disinfection

Directory of Open Access Journals (Sweden)

Chen-Hsing Yu

2014-01-01

Full Text Available This research aimed to develop an electrolysis method to generate high-concentration chlorine dioxide (ClO2 for tilapia fillet disinfection. The designed generator produced up to 3500 ppm of ClO2 at up to 99% purity. Tilapia fillets were soaked in a 400 ppm ClO2 solution for 5, 10, and 25 min. Results show that total plate counts of tilapia, respectively, decreased by 5.72 to 3.23, 2.10, and 1.09 log CFU/g. In addition, a 200 ppm ClO2 solution eliminated coliform bacteria and Escherichia coli in 5 min with shaking treatment. Furthermore, ClO2 and trihalomethanes (THMs residuals on tilapia fillets were analyzed by GC/MS and were nondetectable (GC-MS detection limit was 0.12 ppb. The results conform to Taiwan’s environmental protection regulations and act governing food sanitation.

Image Restoration Based on the Hybrid Total-Variation-Type Model

Directory of Open Access Journals (Sweden)

Baoli Shi

2012-01-01

Full Text Available We propose a hybrid total-variation-type model for the image restoration problem based on combining advantages of the ROF model with the LLT model. Since two L1-norm terms in the proposed model make it difficultly solved by using some classically numerical methods directly, we first employ the alternating direction method of multipliers (ADMM to solve a general form of the proposed model. Then, based on the ADMM and the Moreau-Yosida decomposition theory, a more efficient method called the proximal point method (PPM is proposed and the convergence of the proposed method is proved. Some numerical results demonstrate the viability and efficiency of the proposed model and methods.

Chemical characterization of candy made of Erva-Mate (Ilex paraguariensis A. St. Hil.) residue.

Science.gov (United States)

Vieira, Manoela A; Rovaris, Angela A; Maraschin, Marcelo; De Simas, Karina N; Pagliosa, Cristiane M; Podestá, Rossana; Amboni, Renata D M C; Barreto, Pedro L M; Amante, Edna R

2008-06-25

The aim of this work was to evaluate the chemical properties of the residues from erva-mate processing and also to determine the candy-making performance with addition of residues from erva-mate on consumers' acceptance and purchase intent of this new product. The candies containing different amounts of mate powder were evaluated through overall acceptability test and purchase intent. Mate powder showed high contents of dietary fiber, total ash, and total polyphenols. The total dietary fiber content of the mate candies ranged from 5.7 to 6.29% on a dry matter basis. Supplementation with mate powder caused significant increases in polyphenol and mineral contents of mate candies. The incorporation of mate powder increased the hardness of the candies and produced desirable results in their nutritional characteristics. The sensory tests indicated that mate candies were acceptable and approved in relation to purchase intent.

Solid residues

International Nuclear Information System (INIS)

Mulder, E.; Duin, P.J. van; Grootenboer, G.J.

1995-01-01

A summary is presented of the many investigations that have been done on solid residues of atmospheric fluid bed combustion (AFBC). These residues are bed ash, cyclone ash and bag filter ash. Physical and chemical properties are discussed and then the various uses of residues (in fillers, bricks, gravel, and for recovery of aluminium) are summarised. Toxicological properties of fly ash and stack ash are discussed as are risks of pneumoconiosis for workers handling fly ash, and contamination of water by ashes. On the basis of present information it is concluded that risks to public health from exposure to emissions of coal fly ash from AFBC appear small or negligible as are health risk to workers in the coal fly ash processing industry. 35 refs., 5 figs., 12 tabs

vQRS Based on Hybrids of CNT with PMMA-POSS and PS-POSS Copolymers to Reach the Sub-PPM Detection of Ammonia and Formaldehyde at Room Temperature Despite Moisture

Directory of Open Access Journals (Sweden)

Abhishek Sachan

2017-07-01

Full Text Available Nanocomposite-based quantum resistive vapour sensors (vQRS have been developed from the assembly of hybrid copolymers of polyhedral oligomeric silsesquioxane (POSS and poly(methyl methacrylate (PMMA or poly(styrene (PS with carbon nanotubes (CNT. The originality of the resulting conducting architecture is expected to be responsible for the ability of the transducer to detect sub-ppm concentrations of ammonia and formaldehyde at room temperature despite the presence of humidity. In particular, the boosting effect of POSS is evidenced in CNT-based nanocomposite vQRS. The additive fabrication by spraying layer-by-layer provides (sLbL is an effective method to control the reproducibility of the transducers’ chemo-resistive responses. In dry atmosphere, the two types of sensors showed a high sensitivity towards both hazardous gases, as they were able to detect 300 ppb of formaldehyde and 500 ppb of ammonia with a sufficiently good signal to noise ratio (SNR > 10. They also exhibited a quick response times less than 5 s for both vapours and, even in the presence of 100 ppm of water, they were able to detect small amounts of gases (1.5 ppm of NH3 and 9 ppm of CH2O. The results suggest promising applications of POSS-based vQRS for air quality or volatolome monitoring.

Effects of environmental pollutants on Connecticut and Maryland ospreys

Science.gov (United States)

Wiemeyer, Stanley N.; Spitzer, P.R.; Krantz, W.C.; Lamont, T.G.; Cromartie, E.

1975-01-01

Osprey (Pandion haliaetus) eggs were exchanged between Connecticut and Maryland osprey nests in 1968 and 1969 to test the hypothesis that the decline in reproductive success of Connecticut ospreys was caused by something within the external environment of the eggs. Incubation of 30 Connecticut osprey eggs by Maryland ospreys did not improve the hatching rate. Forty-five Maryland osprey eggs incubated by Connecticut ospreys hatched at their normal rate. The results of the egg exchanges and associated observations indicated that the most probable cause of the poor reproduction of Connecticut ospreys ,was related to contamination of the birds and their eggs. Residues of DDT and its metabolites, dieldrin, and PCBs were generally higher in fish from Connecticut than from Maryland. During 1968-69, average residues (on a nest basis) in osprey eggs from Maryland were: p,p'-DDE, 2.4 ppm; dieldrin, 0.25 ppm; PCB, 2.6 ppm. Average residues in eggs from Connecticut for the same period were: p,p'DDE, 8.9 ppm; dieldrin, 0.61 ppm; PCB, 15 ppm. There were no major changes in residue content of Connecticut eggs collected in 1964 compared with those collected in 1968-B9. One Connecticut osprey had a concentration of dieldrin in its brain which was in the lethal range. The average shell thickness of recently collected osprey eggs from Connecticut had declined 18 percent, and those from Maryland had declined 10 percent from pre-1947 norms. Dieldrin, DDE, and PCB are three environmental pollutants that have most likely been important factors in the greatly reduced reproductive success and rapid population decline of Connecticut ospreys.

STUDY ON THE PHYSICOCHEMICAL, ANTIOXIDANT PROPERTIES AND MINERAL CONTENT OF FIVE HONEYS PRODUCED IN THE CENTRAL REGION OF ALGERIA

Directory of Open Access Journals (Sweden)

MOUNIR HABATI

2017-06-01

Full Text Available The present study evaluated the physicochemical, antioxidant properties and mineral content of five Honeys from the Central Region of Algeria (Laghouat. Physicochemical properties were examined according to the official methods of analysis of AOAC (Association of Official Analytical Chemists; antioxidant activities were determined by DPPH (2,2-diphenyl-1-picrylhydrazyl and FRAP (Ferric reducing ability of plasma assays, the minerals were analyzed by atomic absorption spectrometry. The results compared to those recommended by Codex Alimentarius indicated that the quality of the tested honey was very good. The samples exhibited good antioxidant activity. A linear positive relationship existed between antioxidant activity and total phenolics (R2 = 0.95/flavonoids (R2 = 0.99. The analyzed honey samples possess valuable antioxidants for culinary and medicinal uses. The analysis revealed the presence of (K 220.88 ± 1.72 ppm, (Na 85.84 ± 1.72 ppm, (Fe 0.1922 ± 0.47 ppm, (Co 0.9144 ± 1.63 ppm, (Cu 0.1252 ± 1.76 ppm and nickel (Ni 0.0463 ± 0.10 ppm in the collected samples. Toxic elements identified in the studied honeys are safe because they are below the maximum residual limit. Therefore, these results indicate that the areas of production of these honeys are unpolluted by the toxic elements.

Residual transpiration as a component of salinity stress tolerance mechanism: a case study for barley.

Science.gov (United States)

Hasanuzzaman, Md; Davies, Noel W; Shabala, Lana; Zhou, Meixue; Brodribb, Tim J; Shabala, Sergey

2017-06-19

While most water loss from leaf surfaces occurs via stomata, part of this loss also occurs through the leaf cuticle, even when the stomata are fully closed. This component, termed residual transpiration, dominates during the night and also becomes critical under stress conditions such as drought or salinity. Reducing residual transpiration might therefore be a potentially useful mechanism for improving plant performance when water availability is reduced (e.g. under saline or drought stress conditions). One way of reducing residual transpiration may be via increased accumulation of waxes on the surface of leaf. Residual transpiration and wax constituents may vary with leaf age and position as well as between genotypes. This study used barley genotypes contrasting in salinity stress tolerance to evaluate the contribution of residual transpiration to the overall salt tolerance, and also investigated what role cuticular waxes play in this process. Leaves of three different positions (old, intermediate and young) were used. Our results show that residual transpiration was higher in old leaves than the young flag leaves, correlated negatively with the osmolality, and was positively associated with the osmotic and leaf water potentials. Salt tolerant varieties transpired more water than the sensitive variety under normal growth conditions. Cuticular waxes on barley leaves were dominated by primary alcohols (84.7-86.9%) and also included aldehydes (8.90-10.1%), n-alkanes (1.31-1.77%), benzoate esters (0.44-0.52%), phytol related compounds (0.22-0.53%), fatty acid methyl esters (0.14-0.33%), β-diketones (0.07-0.23%) and alkylresorcinols (1.65-3.58%). A significant negative correlation was found between residual transpiration and total wax content, and residual transpiration correlated significantly with the amount of primary alcohols. Both leaf osmolality and the amount of total cuticular wax are involved in controlling cuticular water loss from barley leaves under well

Microbiological quality and antibiotic residues in informally marketed raw cow milk within the coastal savannah zone of Ghana.

Science.gov (United States)

Addo, K K; Mensah, G I; Aning, K G; Nartey, N; Nipah, G K; Bonsu, C; Akyeh, M L; Smits, H L

2011-02-01

To investigate the microbiological quality and the presence of antibiotic residues in raw cow milk and in some indigenous milk products produced and marketed by the informal sector in the coastal savannah zone of Ghana. Milk samples were aseptically collected from 224 kraals and samples of 26 indigenous milk products were purchased from processors and retailers. Total plate counts, total coliform counts and the presence of Escherichia coli and E. coli O157:H7 were determined in all 250 samples. Milk samples were also tested for antibiotic residues. Total plate counts exceeded 10⁵ CFU/ml in 45.2% of the samples while coliforms exceeded 10³ CFU/ml in 66.0% and E. coli was detected in 11.2%. E. coli was present in raw cow milk but not in the indigenous products and all E. coli isolates were negative for E. coli O157:H7. Antibiotic residues were detected in 3.1% of the raw cow milk samples. Bulk milk contains unacceptable levels of hygiene indicators and antibiotic residues and is a potential source of milk-borne infections. The detection of E. coli and antibiotic residues raises public health concerns about the safety of fresh unpasteurized cow milk in the coastal savannah zone of Ghana and calls for improved farm hygiene, the need for milk pasteurization and the sensible use of antibiotics in the milk industry. © 2010 Blackwell Publishing Ltd.

[Construction of a microbial consortium RXS with high degradation ability for cassava residues and studies on its fermentative characteristics].

Science.gov (United States)

He, Jiang; Mao, Zhong-Gui; Zhang, Qing-Hua; Zhang, Jian-Hua; Tang, Lei; Zhang, Hong-Jian

2012-03-01

A microbial consortium with high effective and stable cellulosic degradation ability was constructed by successive enrichment and incubation in a peptone cellulose medium using cassava residues and filter paper as carbon sources, where the inoculums were sampled from the environment filled with rotten lignocellulosic materials. The degradation ability to different cellulosic materials and change of main parameters during the degradation process of cassava residues by this consortium was investigated in this study. It was found that, this consortium can efficiently degrade filter paper, absorbent cotton, avicael, wheat-straw and cassava residues. During the degradation process of cassava residues, the key hydrolytic enzymes including cellulase, hemicellulase and pectinase showed a maximum enzyme activity of 34.4, 90.5 and 15.8 U on the second or third day, respectively. After 10 days' fermentation, the degradation ratio of cellulose, hemicellulose and lignin of cassava residues was 79.8%, 85.9% and 19.4% respectively, meanwhile the loss ratio of cassava residues reached 61.5%. Otherwise,it was found that the dominant metabolites are acetic acid, butyric acid, caproic acid and glycerol, and the highest hydrolysis ratio is obtained on the second day by monitoring SCOD, total volatile fatty acids and total sugars. The above results revealed that this consortium can effectively hydrolyze cassava residues (the waste produced during the cassava based bioethanol production) and has great potential to be utilized for the pretreatment of cassava residues for biogas fermentation.

Determination of residual acetone and acetone related impurities in drug product intermediates prepared as Spray Dried Dispersions (SDD) using gas chromatography with headspace autosampling (GCHS).

Science.gov (United States)

Quirk, Emma; Doggett, Adrian; Bretnall, Alison

2014-08-05

Spray Dried Dispersions (SDD) are uniform mixtures of a specific ratio of amorphous active pharmaceutical ingredient (API) and polymer prepared via a spray drying process. Volatile solvents are employed during spray drying to facilitate the formation of the SDD material. Following manufacture, analytical methodology is required to determine residual levels of the spray drying solvent and its associated impurities. Due to the high level of polymer in the SDD samples, direct liquid injection with Gas Chromatography (GC) is not a viable option for analysis. This work describes the development and validation of an analytical approach to determine residual levels of acetone and acetone related impurities, mesityl oxide (MO) and diacetone alcohol (DAA), in drug product intermediates prepared as SDDs using GC with headspace (HS) autosampling. The method development for these analytes presented a number of analytical challenges which had to be overcome before the levels of the volatiles of interest could be accurately quantified. GCHS could be used after two critical factors were implemented; (1) calculation and application of conversion factors to 'correct' for the reactions occurring between acetone, MO and DAA during generation of the headspace volume for analysis, and the addition of an equivalent amount of polymer into all reference solutions used for quantitation to ensure comparability between the headspace volumes generated for both samples and external standards. This work describes the method development and optimisation of the standard preparation, the headspace autosampler operating parameters and the chromatographic conditions, together with a summary of the validation of the methodology. The approach has been demonstrated to be robust and suitable to accurately determine levels of acetone, MO and DAA in SDD materials over the linear concentration range 0.008-0.4μL/mL, with minimum quantitation limits of 20ppm for acetone and MO, and 80ppm for DAA. Copyright

Tratamiento Híbrido de agua residual gris doméstica

Directory of Open Access Journals (Sweden)

Pablo Paredes

2013-07-01

Full Text Available El reúso del agua residual gris doméstica es una práctica que también puede aplicarse en nuestro país. Este reúso ayudaria a reducir los costos de consumo de agua potable que actualmente poseen las personas de estratos medio y bajo en el país. Este estudio aplica un concepto nuevo de sistema de tratamiento híbrido para descontaminar el agua y poderla reusar para riego de jardines o para llenar el tanque de los inodoros en una vivienda. Un tratamiento de agua residual gris doméstica híbrido plantea la consecución de remociones totales de materia orgánica, sólidos suspendidos totales, coliformes fecales del 93 %, 92 % y 99,2 %, respectivamente. Este tipo de tratamiento puede tener un valor agregado al disminuir las descargas de aguas servidas a través del sistema de alcantarillado sanitario, con el abaratamiento de la infraestructura para los organismos seccionales del país.

Cytotoxic effects of oxytetracycline residues in the bones of broiler chickens following therapeutic oral administration of a water formulation.

Science.gov (United States)

Odore, R; De Marco, M; Gasco, L; Rotolo, L; Meucci, V; Palatucci, A T; Rubino, V; Ruggiero, G; Canello, S; Guidetti, G; Centenaro, S; Quarantelli, A; Terrazzano, G; Schiavone, A

2015-08-01

Tetracyclines, which represent one of the most commonly used antibiotics for poultry, are known to be deposited in bones, where they can remain, despite the observation of appropriate withdrawal times. The aim of the study was to determine the concentration of oxytretracycline (OTC) residues in the bone and muscle of chickens, following the oral administration of a commercially available liquid formulation, and to test their cytotoxic effects on an in vitro cell culture model. Seventy-two 1-day-old broiler chickens were randomly allotted into 2 groups (control and treated animals). OTC (40 mg/kg BW) was administered via drinking water during the 1 to 5 and 20 to 25 days of life periods. At the end of the trial, the birds were slaughtered and the OTC residues in the target tissues were measured by means of liquid chromatography (LC) - tandem mass spectrometry (MS/MS). Cytotoxicity was assessed by evaluating the pro-apoptotic effect of the bone residues on the K562 erythroleukemic line and on the peripheral blood mononuclear cells (PBMC). In all the animals, the OTC residues in the muscle were far below the established MRL of 100 μg/kg. The OTC levels in the bones of the treated animals were instead found in the parts per million (ppm) range. Cell cytotoxicity was assessed by evaluating the pro-apoptotic effect of OTC bone residues on the haematopoietic cell system. This in vitro system has revealed a significant pro-apoptotic effect on both the K562 cell line and PBMC cultures. This result suggests potential human and animal health risks due to the entry of tetracycline residues contained in the bones of treated livestock into the food-chain. This could be of concern, particularly for canine and feline diets, as meat, bone meal, and poultry by-products represent some of the main ingredients of pet foods, especially in the case of dry pet food. Further studies are needed to define the underlying mechanisms of cytotoxicity and to evaluate the in vivo toxicological

Determination of total organic phosphorus in samples of mineral soils

Directory of Open Access Journals (Sweden)

Armi Kaila

1962-01-01

Full Text Available In this paper some observations on the estimation of organic phosphorus in mineral soils are reported. The fact is emphasized that the accuracy of all the methods available is relatively poor. Usually, there are no reasons to pay attention to differences less than about 20 ppm. of organic P. Analyses performed on 345 samples of Finnish mineral soils by the extraction method of MEHTA et. al. (10 and by a simple procedure adopted by the author (successive extractions with 4 N H2SO4 and 0.5 N NaOH at room temperature in the ratio of 1 to 100 gave, on the average, equal results. It seemed to be likely that the MEHTA method removed the organic phosphorus more completely than did the less vigorous method, but in the former the partial hydrolysis of organic phosphorus compounds tends to be higher than in the latter. An attempt was made to find out whether the differences between the respective values for organic phosphorus obtained by an ignition method and the simple extraction method could be connected with any characteristics of the soil. No correlation or only a low correlation coefficient could be calculated between the difference in the results of these two methods and e. g. the pH-value, the content of clay, organic carbon, aluminium and iron soluble in Tamm’s acid oxalate, the indicator of the phosphate sorption capacity, or the »Fe-bound» inorganic phosphorus, respectively. The absolute difference tended to increase with an increase in the content of organic phosphorus. For the 250 samples of surface soils analyzed, the ignition method gave values which were, on the average, about 50 ppm. higher than the results obtained by the extraction procedure. The corresponding difference for the 120 samples from deeper layers was about 20 ppm of organic P. The author recommends, for the present, the determination of the total soil organic phosphorus as an average of the results obtained by the ignition method and the extraction method.

Experimental determination of the constitution and the phase relationships in Zr (2.5-8.0)at.%Nb (0-6.7)at.%Al alloys with 750at.ppm0 and 250at.ppmN, between 730-900 deg C

International Nuclear Information System (INIS)

Peruzzi Bardella, A.; Bolcich, J.C.

1990-01-01

Zr alloys with 2.5 to 8.0 at%Nb and 0 to 6.7 at%Al, were subjected to dynamic and static treatments between 730-900 deg C and studied by qualitative and quantitative optical metallography, electrical resistance, X-ray diffractometry and electron microanalysis. The experimental data were analyzed by taking into account the effects of oxygen and nitrogen impurities. The main results for Zr-Nb-Al alloys with 750 at.ppm0 and 250 at.ppmN are the following: a) Equilibrium relationships are established between α (hcp), β (bcc) and Zr 3 Al (Cu 3 Au) phases along isothermal sections at 730, 771 and 800 deg C. b) β/α+β boundaries are determined along iso-aluminium vertical sections at 6.7, 3.3 and 0 at%Al. As for the first two iso-aluminium sections, the β/α+β equilibrium boundary corresponding to the binary Zr-Nb system is found to have a positive curvature, which is contrary to what has been reported in the literature. The increase in the Al content shifts the T β/α+β at a rate of 5.1 to 8.5 deg C/at.%Al, depending on Nb content. c) The addition of Al to Zr-Nb alloys increases the partial solubility of Nb in the α phase, its maximum value at 730 deg C being about 0.7-0.8 at% for 4 at%Al. d) Solubility values for Al in α-phase of Zr-Al were estimated by extrapolation from ternary alloys. These estimates help to solve an existing discrepancy on the Zr-Al system. (Author)

76 FR 79146 - Propylene Oxide; Proposed Tolerance Actions

Science.gov (United States)

2011-12-21

...: EPA is proposing to establish the tree nut crop group tolerance and separate tolerances on pistachio... (pistachios, pine nuts) in 40 CFR 180.491(a)(1) for residues of propylene oxide in or on pistachio at 300 ppm... pistachio at 10.0 ppm and nut, pine at 10.0 ppm. Establishment of tolerances for pistachios, pine nuts, and...

Handling of Solid Residues

International Nuclear Information System (INIS)

Medina Bermudez, Clara Ines

1999-01-01

The topic of solid residues is specifically of great interest and concern for the authorities, institutions and community that identify in them a true threat against the human health and the atmosphere in the related with the aesthetic deterioration of the urban centers and of the natural landscape; in the proliferation of vectorial transmitters of illnesses and the effect on the biodiversity. Inside the wide spectrum of topics that they keep relationship with the environmental protection, the inadequate handling of solid residues and residues dangerous squatter an important line in the definition of political and practical environmentally sustainable. The industrial development and the population's growth have originated a continuous increase in the production of solid residues; of equal it forms, their composition day after day is more heterogeneous. The base for the good handling includes the appropriate intervention of the different stages of an integral administration of residues, which include the separation in the source, the gathering, the handling, the use, treatment, final disposition and the institutional organization of the administration. The topic of the dangerous residues generates more expectation. These residues understand from those of pathogen type that are generated in the establishments of health that of hospital attention, until those of combustible, inflammable type, explosive, radio-active, volatile, corrosive, reagent or toxic, associated to numerous industrial processes, common in our countries in development

Soluble carbon in oxisol under the effect of organic residue rates

Directory of Open Access Journals (Sweden)

Gabriela Lúcia Pinheiro

2014-06-01

Full Text Available The application of organic residues to the soil can increase soluble organic carbon (SOC and affect the pH and electrolytic conductivity (EC of the soil. However, the magnitude of these changes depends on the type of residue and the applied dose. This study aimed to evaluate the effect of increasing C rates contained in organic residue on the pH, EC, water-extractable total carbon (WETC, water-extractable organic carbon (WEOC, and water-extractable inorganic carbon (WEIC in soil treated with manure (chicken, swine, and quail, sawdust, coffee husk, and sewage sludge. The levels of total C (TC- KH2PO4, organic carbon (OC- KH2PO4, and inorganic C (IC- KH2PO4 extractable by a 0.1 mol L-1 KH2PO4 solution were also quantified in soil under the effect of increasing rates of chicken and quail manures. The following rates of organic residue C were applied to a dystrophic Red Latosol (Oxisol sample: 0, 2,000, 5,000, 10,000, and 20,000 mg kg-1. The addition of organic residues to the soil increased pH, except in the case of sewage sludge, which acidified the soil. The acidity correction potential of chicken and quail manure was highest, dependent on the manure rate applied; regardless of the dose used, sawdust barely alters the soil pH. At all tested rates, the EC of the soil treated with swine manure, coffee husk, and sawdust remained below 2.0 dS m-1, which is a critical level for salinity-sensitive crops. However, the application of chicken or quail manure and sewage sludge at certain rates increased the EC to values above this threshold level. Highest levels of WETC, WEOC, and WEIC were obtained when chicken and quail manure and coffee husk were applied to the Oxisol. The quantities of SOC extracted by KH2PO4 were higher than the quantities extracted by water, demonstrating the ability of soil to adsorb C into its colloids.

Pesticides residue levels in selected fruits from some Ghanaian markets

International Nuclear Information System (INIS)

Bempah, K.C.

2009-02-01

The amount of some pesticide residues in fruits was monitored at five (5) Accra Metropolis markets. Locally produced fruits (pawpaw and tomato) and imported apples were purchased from two supermarkets and three urban markets in Accra metropolis and analyzed by gas chromatography equipped with electron capture detector for pesticide residues. A total of 220 samples of fruits were extracted and analyzed for pesticide residues, mainly organochlorines (γ-HCH, δ-HCH, aldrin, heptachlor, γ-chlordane, heptachlor epoxide, α-endosulfan, p,p'-DDE, endrin, β-endosulfan, o,p'-DDT, endrin aldehyde, p,p'- DDT, endrin ketone and methoxychlor). The data showed that most of the fruit samples analyzed contain residues of the monitored pesticides above the accepted maximum residue limit (MRL) as adopted by the FAO/WHO Codex Alimentarius Commission (CAC). The results obtained showed that 38.6 % fruit samples showed results above the MRL, 48.7 % were below the MRL and 12.7 % contained no detectable level of the monitored pesticides. Data analysis of health risk estimates indicated that, particularly γ-HCH, δ-HCH, o,p'-DDT, p,p'-DDE or p,p'-DDT do not pose a direct hazard to human health, although present in the three fruits (pawpaw, tomato and apple). However, heptachlor, heptachlor epoxide, endrin aldehyde, and endrin ketone levels exceeded the reference dose, indicating a great potential for systemic toxicity, especially in children who are considered to be the most vulnerable population subgroup. Lastly, the public is aware of pesticide residues in fruits and advocates for the curtailing of pesticide use on horticulture produce or strong educational programmes for farmers on control and safer use of pesticides. (au)

Nitrous oxide production from soils amended with biogas residues and cattle slurry.

Science.gov (United States)

Abubaker, J; Odlare, M; Pell, M

2013-07-01

The amount of residues generated from biogas production has increased dramatically due to the worldwide interest in renewable energy. A common way to handle the residues is to use them as fertilizers in crop production. Application of biogas residues to agricultural soils may be accompanied with environmental risks, such as increased NO emission. In 24-d laboratory experiments, NO dynamics and total production were studied in arable soils (sandy, clay, and organic) amended with one of two types of anaerobically digested biogas residues (BR-A and BR-B) generated from urban and agricultural waste and nondigested cattle slurry (CS) applied at rates corresponding to 70 kg NH-N ha. Total NO-N losses from the sandy soil were higher after amendment with BR-B (0.32 g NO-N m) than BR-A or CS (0.02 and 0.18 g NO-N m, respectively). In the clay soil, NO-N losses were very low for CS (0.02 g NO-N m) but higher for BR-A and BR-B (0.25 and 0.15 g NO-N m, respectively). In the organic soil, CS gave higher total NO-N losses (0.31 g NO-N m) than BR-A or BR-B (0.09 and 0.08 g NO-N m, respectively). Emission peaks differed considerably between soils, occurring on Day 1 in the organic soil and on Days 11 to 15 in the sand, whereas in the clay the peak varied markedly (Days 1, 6, and 13) depending on residue type. In all treatments, NH concentration decreased with time, and NO concentration increased. Potential ammonium oxidation and potential denitrification activity increased significantly in the amended sandy soil but not in the organic soil and only in the clay amended with CS. The results showed that fertilization with BR can increase NO emissions and that the size is dependent on the total N and organic C content of the slurry and on soil type. In conclusion, the two types of BR and the CS are not interchangeable regarding their effects on NO production in different soils, and, hence, matching fertilizer type to soil type could reduce NO emissions. For instance, it could be

Assessing potential forest and steel inter-industry residue utilisation by sequential chemical extraction

Energy Technology Data Exchange (ETDEWEB)

Makela, M.

2012-10-15

Traditional process industries in Finland and abroad are facing an emerging waste disposal problem due recent regulatory development which has increased the costs of landfill disposal and difficulty in acquiring new sites. For large manufacturers, such as the forest and ferrous metals industries, symbiotic cooperation of formerly separate industrial sectors could enable the utilisation waste-labeled residues in manufacturing novel residue-derived materials suitable for replacing commercial virgin alternatives. Such efforts would allow transforming the current linear resource use and disposal models to more cyclical ones and thus attain savings in valuable materials and energy resources. The work described in this thesis was aimed at utilising forest and carbon steel industry residues in the experimental manufacture of novel residue-derived materials technically and environmentally suitable for amending agricultural or forest soil properties. Single and sequential chemical extractions were used to compare the pseudo-total concentrations of trace elements in the manufactured amendment samples to relevant Finnish statutory limit values for the use of fertilizer products and to assess respective potential availability under natural conditions. In addition, the quality of analytical work and the suitability of sequential extraction in the analysis of an industrial solid sample were respectively evaluated through the analysis of a certified reference material and by X-ray diffraction of parallel sequential extraction residues. According to the acquired data, the incorporation of both forest and steel industry residues, such as fly ashes, lime wastes, green liquor dregs, sludges and slags, led to amendment liming capacities (34.9-38.3%, Ca equiv., d.w.) comparable to relevant commercial alternatives. Only the first experimental samples showed increased concentrations of pseudo-total cadmium and chromium, of which the latter was specified as the trivalent Cr(III). Based on

Characterization of Residual Stress Effects on Fatigue Crack Growth of a Friction Stir Welded Aluminum Alloy

Science.gov (United States)

Newman, John A.; Smith, Stephen W.; Seshadri, Banavara R.; James, Mark A.; Brazill, Richard L.; Schultz, Robert W.; Donald, J. Keith; Blair, Amy

2015-01-01

An on-line compliance-based method to account for residual stress effects in stress-intensity factor and fatigue crack growth property determinations has been evaluated. Residual stress intensity factor results determined from specimens containing friction stir weld induced residual stresses are presented, and the on-line method results were found to be in excellent agreement with residual stress-intensity factor data obtained using the cut compliance method. Variable stress-intensity factor tests were designed to demonstrate that a simple superposition model, summing the applied stress-intensity factor with the residual stress-intensity factor, can be used to determine the total crack-tip stress-intensity factor. Finite element, VCCT (virtual crack closure technique), and J-integral analysis methods have been used to characterize weld-induced residual stress using thermal expansion/contraction in the form of an equivalent delta T (change in local temperature during welding) to simulate the welding process. This equivalent delta T was established and applied to analyze different specimen configurations to predict residual stress distributions and associated residual stress-intensity factor values. The predictions were found to agree well with experimental results obtained using the crack- and cut-compliance methods.

A One ppm NDIR Methane Gas Sensor with Single Frequency Filter Denoising Algorithm

Directory of Open Access Journals (Sweden)

Binqing Jiang

2012-09-01

Full Text Available A non-dispersive infrared (NDIR methane gas sensor prototype has achieved a minimum detection limit of 1 parts per million by volume (ppm. The central idea of the design of the sensor is to decrease the detection limit by increasing the signal to noise ratio (SNR of the system. In order to decrease the noise level, a single frequency filter algorithm based on fast Fourier transform (FFT is adopted for signal processing. Through simulation and experiment, it is found that the full width at half maximum (FWHM of the filter narrows with the extension of sampling period and the increase of lamp modulation frequency, and at some optimum sampling period and modulation frequency, the filtered signal maintains a noise to signal ratio of below 1/10,000. The sensor prototype provides the key techniques for a hand-held methane detector that has a low cost and a high resolution. Such a detector may facilitate the detection of leakage of city natural gas pipelines buried underground, the monitoring of landfill gas, the monitoring of air quality and so on.

Ammonia volatilization from crop residues and frozen green manure crops

Science.gov (United States)

de Ruijter, F. J.; Huijsmans, J. F. M.; Rutgers, B.

2010-09-01

Agricultural systems can lose substantial amounts of nitrogen (N). To protect the environment, the European Union (EU) has adopted several directives that set goals to limit N losses. National Emission Ceilings (NEC) are prescribed in the NEC directive for nitrogen oxides and ammonia. Crop residues may contribute to ammonia volatilization, but sufficient information on their contribution to the national ammonia volatilization is lacking. Experiments were carried out with the aim to assess the ammonia volatilization of crop residues left on the soil surface or incorporated into the soil under the conditions met in practice in the Netherlands during late autumn and winter. Ammonia emission from residues of broccoli, leek, sugar beet, cut grass, fodder radish (fresh and frozen) and yellow mustard (frozen) was studied during two winter seasons using volatilization chambers. Residues were either placed on top of soil or mixed with soil. Mixing residues with soil gave insignificant ammonia volatilization, whereas volatilization was 5-16 percent of the N content of residues when placed on top of soil. Ammonia volatilization started after at least 4 days. Total ammonia volatilization was related to C/N-ratio and N concentration of the plant material. After 37 days, cumulative ammonia volatilization was negligible from plant material with N concentration below 2 percent, and was 10 percent of the N content of plant material with 4 percent N. These observations can be explained by decomposition of plant material by micro-organisms. After an initial built up of the microbial population, NH 4+ that is not needed for their own growth is released and can easily emit as NH 3 at the soil surface. The results of the experiments were used to estimate the contribution of crop residues to ammonia volatilization in the Netherlands. Crop residues of arable crops and residues of pasture topping may contribute more than 3 million kg NH 3-N to the national ammonia volatilization of the

[Factors affecting residual stones after percutaneous nephrolithotomy in patients with renal calculus].

Science.gov (United States)

Qiao, Mingzhou; Zhang, Haifang; Zhou, Chenlong

2015-11-24

To explore the factors affecting the residual stones after percutaneous nephrolithotomy (PCNL) in patients with renal calculus. A retrospective analysis was performed for 1 200 patients who were affected by renal calculus and treated with PCNL between Jan 2008 and May 2014 in People's Hospital of Anyang City. Among those patients, 16 were diagnosed as bilateral renal stone and had two successive operations. The size, location and number of stones, previous history of surgery, the degree of hydronephrosis, urinary infection were included in the univariate analysis. Significant factors in univariate analysis were included in the multivariate analysis to determine factors affecting stone residual. A total of 385 cases developed stone residual after surgery. The overall residual rate was 31.7%. In univariate analysis, renal pelvis combined with caliceal calculus (P=0.006), stone size larger than 4 cm (P=0.005), stone number more than 4 (P=0.002), the amount of bleeding more than 200 ml (P=0.025), operation time longer than 120 minutes (P=0.028) were associated with an increased rate of stone residual. When subjected to the Cox multivariate analysis, the independent risk factors for residual stones were renal pelvis combined with caliceal calculus (P=0.049), stone size larger than 4 cm (P=0.038) and stone number more than 4 (P=0.018). Factors affecting the incidence of residual stones after PCNL are the size, location and number of stones. Larger size stone and the presence of renal pelvis combined with caliceal calculus are significantly associated with residual stones. Nevertheless, stone number less than 4 indicates an increased stone clearance rate.

Utilization of protein-rich residues in biotechnological processes.

Science.gov (United States)

Pleissner, Daniel; Venus, Joachim

2016-03-01

A drawback of biotechnological processes, where microorganisms convert biomass constituents, such as starch, cellulose, hemicelluloses, lipids, and proteins, into wanted products, is the economic feasibility. Particularly the cost of nitrogen sources in biotechnological processes can make up a large fraction of total process expenses. To further develop the bioeconomy, it is of considerable interest to substitute cost-intensive by inexpensive nitrogen sources. The aim of this mini-review was to provide a comprehensive insight of utilization methods of protein-rich residues, such as fish waste, green biomass, hairs, and food waste. The methods described include (i) production of enzymes, (ii) recovery of bioactive compounds, and/or (iii) usage as nitrogen source for microorganisms in biotechnological processes. In this aspect, the utilization of protein-rich residues, which are conventionally considered as waste, allows the development of value-adding processes for the production of bioactive compounds, biomolecules, chemicals, and materials.

Effect of the interaction between diet composition and the PPM1K genetic variant on insulin resistance and β cell function markers during weight loss: results from the Nutrient Gene Interactions in Human Obesity: implications for dietary guidelines (NUGENOB) randomized trial.

Science.gov (United States)

Goni, Leticia; Qi, Lu; Cuervo, Marta; Milagro, Fermín I; Saris, Wim H; MacDonald, Ian A; Langin, Dominique; Astrup, Arne; Arner, Peter; Oppert, Jean-Michel; Svendstrup, Mathilde; Blaak, Ellen E; Sørensen, Thorkild Ia; Hansen, Torben; Martínez, J Alfredo

2017-09-01

Background: Circulating branched-chain amino acids (BCAAs) and aromatic amino acids (AAAs) have been shown to be associated with insulin resistance and diabetes risk. The common rs1440581 T allele in the protein phosphatase Mg2+/Mn2+ dependent 1K ( PPM1K ) gene has been related to elevated BCAA concentrations and risk of type 2 diabetes. Objective: In the present study, we tested whether dietary fat and carbohydrate intakes influenced the association between the rs1440581 PPM1K genetic variant and glucose-metabolism traits during weight loss. Design: The rs1440581 PPM1K genetic variant was genotyped in a total of 757 nondiabetic individuals who were randomly assigned to 1 of 2 energy-restricted diets that differed in macronutrient composition (low-fat diet: 20-25% fat, 15% protein, and 60-65% carbohydrate; high-fat diet: 40-45% fat, 15% protein, and 40-45% carbohydrate). The changes in fasting glucose, fasting insulin, insulin resistance (homeostasis model assessment of insulin resistance) and homeostasis model assessment of β cell function (HOMA-B) were measured after a mean ± SD weight loss of 6.8 ± 3.4 kg over 10 wk and analyzed according to the presence of the T allele of rs1440581. Results: The rs1440581 T allele was associated with a smaller improvement in glucose concentrations after the 10-wk dietary intervention (β ± SE: 0.05 ± 0.02 mg/dL; P = 0.03). In addition, significant gene-diet interactions were shown for the rs1440581 PPM1K genetic variant in relation to changes in insulin and HOMA-B ( P -interaction = 0.006 and 0.002, respectively). In response to the high-fat diet, the T allele was associated with a higher reduction of insulin (β ± SE: -0.77 ± 0.40 μU/mL; P = 0.04) and HOMA-B (β ± SE: -13.2 ± 3.81; P = 0.003). An opposite effect was observed in the low-fat diet group, although in this group the T allele was marginally ( P = 0.10) and not significantly ( P = 0.24) associated with insulin and HOMA-B, respectively. Conclusion: PPM1K rs

Utilization of steel, pulp and paper industry solid residues in forest soil amendment: relevant physicochemical properties and heavy metal availability.

Science.gov (United States)

Mäkelä, Mikko; Watkins, Gary; Pöykiö, Risto; Nurmesniemi, Hannu; Dahl, Olli

2012-03-15

Industrial residue application to soil was investigated by integrating granulated blast furnace or converter steel slag with residues from the pulp and paper industry in various formulations. Specimen analysis included relevant physicochemical properties, total element concentrations (HCl+HNO3 digestion, USEPA 3051) and chemical speciation of chosen heavy metals (CH3COOH, NH2OH·HCl and H2O2+H2O2+CH3COONH4, the BCR method). Produced matrices showed liming effects comparable to commercial ground limestone and included significant quantities of soluble vital nutrients. The use of converter steel slag, however, led to significant increases in the total concentrations of Cr and V. Subsequently, total Cr was attested to occur as Cr(III) by Na2CO3+NaOH digestion followed by IC UV/VIS-PCR (USEPA 3060A). Additionally, 80.6% of the total concentration of Cr (370 mg kg(-1), d.w.) occurred in the residual fraction. However, 46.0% of the total concentration of V (2470 mg kg(-1), d.w.) occurred in the easily reduced fraction indicating potential bioavailability. Copyright © 2011 Elsevier B.V. All rights reserved.

Active cancellation of residual amplitude modulation in a frequency-modulation based Fabry-Perot interferometer.

Science.gov (United States)

Yu, Yinan; Wang, Yicheng; Pratt, Jon R

2016-03-01

Residual amplitude modulation (RAM) is one of the most common noise sources known to degrade the sensitivity of frequency modulation spectroscopy. RAM can arise as a result of the temperature dependent birefringence of the modulator crystal, which causes the orientation of the crystal's optical axis to shift with respect to the polarization of the incident light with temperature. In the fiber-based optical interferometer used on the National Institute of Standards and Technology calculable capacitor, RAM degrades the measured laser frequency stability and correlates with the environmental temperature fluctuations. We have demonstrated a simple approach that cancels out excessive RAM due to polarization mismatch between the light and the optical axis of the crystal. The approach allows us to measure the frequency noise of a heterodyne beat between two lasers individually locked to different resonant modes of a cavity with an accuracy better than 0.5 ppm, which meets the requirement to further determine the longitudinal mode number of the cavity length. Also, this approach has substantially mitigated the temperature dependency of the measurements of the cavity length and consequently the capacitance.

Transcatheter interruption of large residual flow after device closure of "Type A" patent ductus arteriosus

Directory of Open Access Journals (Sweden)

Anuradha Sridhar

2012-01-01

Full Text Available We report a case of 3-year-old girl who had persistence of large residual flow following transcatheter closure of a 6 mm ′Type A′ patent ductus arteriosus using a 12 × 10 mm duct occluder. Angiography revealed a large left-to-right shunt coursing through and exiting around the implanted device. Near total abolition of the residual shunt was achieved by initial implantation of an embolization coil within the duct occluder and subsequently an Amplatzer duct occluder (ADO II adjacent to the duct occluder. This challenging case describes an additional technique of abolishing a large residual flow in and around a Nitinol duct occluder device.

Modification of hydrogen determinator for total hydrogen analysis in irradiated zircaloy cladding tube

International Nuclear Information System (INIS)

Park, Soon Dal; Choi, Kwnag Soon; Kim, Jong Goo; Joe, Kih Soo; Kim, Won Ho

1999-01-01

A hydrogen determinator was modified and installed in the glove box to analyse total hydrogen content in irradiated zircaloy tube. The analysis method of hydrogen is Inert Gas Fusion(IGF)-Thermal Conductivity Detection(TCD). The hydrogen recoveries of no tin method using Ti and Zr matrix standards, respectively, were available within 3 μg of hydrogen. Also the smaller size of sample showed the better hydrogen recovery. It was found that the hydrogen standard of Ti matrix is available to hydrogen analysis in zircaloy sample. The mean radioactivity of irradiated zircaloy sample was 10 mR/hr and hydrogen concentration was 130 ppm

Use of MRF residue as alternative fuel in cement production.

Science.gov (United States)

Fyffe, John R; Breckel, Alex C; Townsend, Aaron K; Webber, Michael E

2016-01-01

Single-stream recycling has helped divert millions of metric tons of waste from landfills in the U.S., where recycling rates for municipal solid waste are currently over 30%. However, material recovery facilities (MRFs) that sort the municipal recycled streams do not recover 100% of the incoming material. Consequently, they landfill between 5% and 15% of total processed material as residue. This residue is primarily composed of high-energy-content non-recycled plastics and fiber. One possible end-of-life solution for these energy-dense materials is to process the residue into Solid Recovered Fuel (SRF) that can be used as an alternative energy resource capable of replacing or supplementing fuel resources such as coal, natural gas, petroleum coke, or biomass in many industrial and power production processes. This report addresses the energetic and environmental benefits and trade-offs of converting non-recycled post-consumer plastics and fiber derived from MRF residue streams into SRF for use in a cement kiln. An experimental test burn of 118 Mg of SRF in the precalciner portion of the cement kiln was conducted. The SRF was a blend of 60% MRF residue and 40% post-industrial waste products producing an estimated 60% plastic and 40% fibrous material mixture. The SRF was fed into the kiln at 0.9 Mg/h for 24h and then 1.8 Mg/h for the following 48 h. The emissions data recorded in the experimental test burn were used to perform the life-cycle analysis portion of this study. The analysis included the following steps: transportation, landfill, processing and fuel combustion at the cement kiln. The energy use and emissions at each step is tracked for the two cases: (1) The Reference Case, where MRF residue is disposed of in a landfill and the cement kiln uses coal as its fuel source, and (2) The SRF Case, in which MRF residue is processed into SRF and used to offset some portion of coal use at the cement kiln. The experimental test burn and accompanying analysis indicate

A set of constitutive relationships accounting for residual NAPL in the unsaturated zone.

Science.gov (United States)

Wipfler, E L; van der Zee, S E

2001-07-01

Although laboratory experiments show that non-aqueous phase liquid (NAPL) is retained in the unsaturated zone, no existing multiphase flow model has been developed to account for residual NAPL after NAPL drainage in the unsaturated zone. We developed a static constitutive set of saturation-capillary pressure relationships for water, NAPL and air that accounts for both this residual NAPL and entrapped NAPL. The set of constitutive relationships is formulated similarly to the set of scaled relationships that is frequently applied in continuum models. The new set consists of three fluid-phase systems: a three-phase system and a two-phase system, that both comply with the original constitutive model, and a newly introduced residual NAPL system. The new system can be added relatively easily to the original two- and three-phase systems. Entrapment is included in the model. The constitutive relationships of the non-drainable residual NAPL system are based on qualitative fluid behavior derived from a pore scale model. The pore scale model reveals that the amount of residual NAPL depends on the spreading coefficient and the water saturation. Furthermore, residual NAPL is history-dependent. At the continuum scale, a critical NAPL pressure head defines the transition from free, mobile NAPL to residual NAPL. Although the Pc-S relationships for water and total liquid are not independent in case of residual NAPL, two two-phase Pc-S relations can represent a three-phase residual system of Pc-S relations. A newly introduced parameter, referred to as the residual oil pressure head, reflects the mutual dependency of water and oil. Example calculations show consistent behavior of the constitutive model. Entrapment and retention in the unsaturated zone cooperate to retain NAPL. Moreover, the results of our constitutive model are in agreement with experimental observations.

MR spectroscopy of intracranial tuberculomas: A singlet peak at 3.8 ppm as potential marker to differentiate them from malignant tumors.

Science.gov (United States)

Morales, Humberto; Alfaro, David; Martinot, Carlos; Fayed, Nicolas; Gaskill-Shipley, Mary

2015-06-01

The diagnosis of intracranial tuberculomas is often challenging. Our purpose is to describe the most common metabolic patterns of tuberculomas by MR spectroscopy (MRS) with emphasis on potential specific markers. Single-voxel MRS short echo time was performed in 13 cases of tuberculomas proven by histology and/or response to anti-mycobacterial therapy. For comparison MRS was also performed in 19 biopsy-proven malignant tumors (13 high-grade gliomas and six metastasis). Presence of metabolic peaks was assessed visually and categorical variables between groups were compared using chi-square. Metabolite ratios were compared using Mann-Whitney test and diagnostic accuracy of the metabolite ratios was compared using receiver-operating characteristic (ROC) curves analysis. Spectroscopic peaks representing lipids and glutamate/glutamine (Glx) as well as a peak at ∼3.8 ppm were well defined in 77% (10/13), 77% (10/13) and 69% (nine of 13) of tuberculomas, respectively. Lipid and Glx peaks were also present in most of the malignant lesions, 79% (15/19) and 74% (14/19) respectively. However, a peak at ∼3.8 ppm was present in only 10% (two of 19) of the tumor cases (p values between 1.7-1.9 for Cho/Cr and 0.8-0.9 for mI/Cr provided high specificity (91% for both metabolites) and adequate sensitivity (75% and 80%, respectively) for discrimination of malignant lesions. A singlet peak at ∼3.8 ppm is present in the majority of tuberculomas and absent in most malignant tumors, potentially a marker to differentiate these lesions. The assignment of the peak is difficult from our analysis; however, guanidinoacetate (Gua) is a possibility. Higher Cho/Cr and mI/Cr ratios should favor malignant lesions over tuberculomas. The presence of lipids and Glx is non-specific. © The Author(s) 2015.

Pro biotic as Alternative to Antibiotic for Broiler Chicken fed Food Industrial Residual Oil

International Nuclear Information System (INIS)

EL-Faramawy, A.A.; El-Maghraby, A.F.; El-Danasoury, M.M.; Hussien, H.A.; Hegazy, E.S.

2016-01-01

This study aimed to evaluate the effect of pro biotic (some lactic acid bacteria) with different levels of food industrial residual oil in broiler commercial diets on growth performance, meat yield, internal organs, economical efficiency and performance index. One hundred and eighty one day old Cobb chicks (45 ± 0.4 g) were equally and randomly divided into 6 groups namely; the antibiotic with fresh oil (FO), the antibiotic with mixed oil (MO) [FO+RO ( 1:1 w/w)], the antibiotic with food industrial residual oil (RO), the pro biotic with FO, the pro biotic with MO and the pro biotic with RO. Virginiamycin, Phibro, USA (15 ppm), was the antibiotic, while a mixture of lactic acid bacteria is chosen as pro biotic. Both were added to the water. During the experiment which lasted for 42 days, the body weight, the feed intake and the mortality rate were recorded at 2, 4 and 6 weeks of age then the body weight gain, feed conversion ratio, economical efficiency and performance index were calculated. The results revealed that the average body weight, body weight gain and feed consumption significantly (P 0.05) while liver increased significantly (P<0.05) in pro biotic FO and gizzard in all pro biotic group and antibiotic MO. The highest performance index was observed in groups of birds treated with pro biotic with MO followed by birds treated with pro biotic FO without significant difference. It could be concluded that supplementation of pro biotic in broiler diet containing different levels of RO was economically more beneficial than antibiotic

Comparison of Measured Residual Stress in an Extra Thick Multi-pass Weld Using Neutron Diffraction Method and Inherent Strain Method

International Nuclear Information System (INIS)

Park, JeongUng; An, GyuBaek; Woo, Wan Chuck

2015-01-01

With the increase of large-scale containership, a large amount of high-strength steels with extra thick plates is being extensively used. The welding stress existing in the extra thick welded plates has a significant effect on the integrity of the component in terms of brittle fracture and fatigue behavior. It has been reported that welding residual stress distribution in an extra thick plate can affect the propagation path of the crack. Therefore, it is important to measure the distribution of welding residual stresses for the reliable design of the welded structures. So far various researches have been carried out for the determination of residual stresses on the surface of steels. In this paper, the total residual stresses in the 70 mm thick multipass FACW butt joint were measured by integrating initial stress into ISM. Concretely, two methods named as initial stress integrated ISM and initial inherent strain integrated ISM were employed to determine the total residual stresses. Furthermore, the distributions of residual stresses were compared with the results of the Neutron Diffraction Method(NDM). In order to measure the three dimensional residual stresses in the welded joint with initial stresses existing before welding, initial stress integrated ISM and initial inherent strain integrated ISM were developed. The residual stresses in 70 mm-thick butt joint by flux cored arc welding were carried out with a good accuracy using the two developed methods. The residual stresses in welded joint using both initial stress integrated ISM and initial inherent strain integrated ISM agreed well with the results measured by Neutron Diffraction Method. This suggests that the integrated ISM is a reliable method for residual stress measurement if initial stress existed

PENETAPAN RESIDU DAN PERKIRAAN PENETAPAN BATAS MAKSIMUM RESIDU (BMR ORGANOKLORIN PADA SIMPLISIA

Directory of Open Access Journals (Sweden)

Ani Isnawati

2012-10-01

Full Text Available Penggunaaan bahan obat tradisional (simplisia untuk skala industri dan peningkatan produksi tanaman obat dalam skala besar menjadi tidak ekonomis tanpa pestisida. Disatu sisi penggunaan pestisida dapat menguntungkan yaitu menyebabkan toksis pada hama namun disisi lain toksisitas dapat terjadi juga pada manusia, sehingga residu pestisida dalam tanaman obat yang dikonsumsi dalam jangka panjang akan merugikan kesehatan. Batas maksimum Residu (BMR pestisida dalam simplisia baik di Indonesia maupun di negara lain belum ditetapkan. Sehingga untuk itu untuk mengetahui adanya residu pestisida jenis organoklorin yang telah dilarang penggunaannya melalui Permentan No.434.1/kpts/TP.270/7/2001 dan untuk mengetahui batas keamanannya, maka perlu dilakukan penetapan residu organoklorin dalam simplisia dan menetapkan batas keamanan berdasarkan perhitungan secara teoritis. Pengujian residu dilakukan terhadap golongan pestisida organoklorin pada 4 jenis simplisia (daun wungu (Graptophyllum pictum (L Grifl, daun sambiloto Andrographis paniculata Ness, herba pegagan (Centella  asiatica (L Urban, daun tempuyung (Sonchus arvensis (L yang berasal dari 3 lokasi penanaman, yaitu : perkebunan Tanaman Obat Manako (Jawa Barat, Balai Penelitian Tanaman Obat Tawangmangu (BPTO di Jawa Tengah dan Perkebunan Tanaman Obat Purwodadi (Jawa Timur. Pemeriksaan residu pestisida organoklorin menggunakan kromatografi gas dan perhitungan batas keamanan dihitung dengan adanya nilai ADI (Acceptable daily intake yang telah ditetapkan bersama antara JAO dan WHO serta perkiraan banyaknya konsumsi simplisia. Hasil Pengujian residu pestisida organoklorin diperoleh bahwa simplisia daun Wungu (Tawangmangu mengandung residu lindan dengan kadar 0,24 mg/kg, pegagan (Purwodadi, mengandung lindan 0,36 mg/kg dan aldrin 0,31 mg/kg serta pegagan (Manako mengandung heptaklor 0,15 mg/kg dan op-DDE 0,11 mg/kg. Adapun penghitungan BMR heptaklor dan lindan secara teoritis dengan asumsi rata

Genetic control of residual variance of yearling weight in Nellore beef cattle.

Science.gov (United States)

Iung, L H S; Neves, H H R; Mulder, H A; Carvalheiro, R

2017-04-01

There is evidence for genetic variability in residual variance of livestock traits, which offers the potential for selection for increased uniformity of production. Different statistical approaches have been employed to study this topic; however, little is known about the concordance between them. The aim of our study was to investigate the genetic heterogeneity of residual variance on yearling weight (YW; 291.15 ± 46.67) in a Nellore beef cattle population; to compare the results of the statistical approaches, the two-step approach and the double hierarchical generalized linear model (DHGLM); and to evaluate the effectiveness of power transformation to accommodate scale differences. The comparison was based on genetic parameters, accuracy of EBV for residual variance, and cross-validation to assess predictive performance of both approaches. A total of 194,628 yearling weight records from 625 sires were used in the analysis. The results supported the hypothesis of genetic heterogeneity of residual variance on YW in Nellore beef cattle and the opportunity of selection, measured through the genetic coefficient of variation of residual variance (0.10 to 0.12 for the two-step approach and 0.17 for DHGLM, using an untransformed data set). However, low estimates of genetic variance associated with positive genetic correlations between mean and residual variance (about 0.20 for two-step and 0.76 for DHGLM for an untransformed data set) limit the genetic response to selection for uniformity of production while simultaneously increasing YW itself. Moreover, large sire families are needed to obtain accurate estimates of genetic merit for residual variance, as indicated by the low heritability estimates (Box-Cox transformation was able to decrease the dependence of the variance on the mean and decreased the estimates of genetic parameters for residual variance. The transformation reduced but did not eliminate all the genetic heterogeneity of residual variance, highlighting

Residual magnetic field in rotary machines; Campo magnetico residual en maquinas rotatorias

Energy Technology Data Exchange (ETDEWEB)

Gonzalez V, Esteban A; Apanco R, Marcelino [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2007-07-01

The residual magnetism is a phenomenon in which the magnetic dipoles of a substance are oriented in a certain degree. On the other hand, when internal forces exist capable of aligning elementary magnetic dipoles of a material, a permanent magnet is obtained. Just as in a conductor or in a material, in the elements of a rotary electrical machine magnetic fields can be induced that produce a residual magnetism or magnetization. In the rotary electrical machines, the magnetization phenomenon causes serious problems, such as the generation of induced currents that propitiate the mechanical wear in bearings, collars, trunnions and inclusive in the shaft, by effects known as pitting, frosting and spark tracks, as well as erroneous readings in vibration and temperature sensors, that in some cases can cause the shut down of the machine. In this article are presented the general concepts on the residual magnetism in rotary electrical machines, the causes that originate it and the problems that arises, as well as the demagnetization of the components that have residual magnetic field. The results obtained by the area of Electrical Equipment of the Instituto de Investigaciones Electricas are revised, during the execution of activities related to the measurement and elimination of the residual magnetic field in rotary electrical machines. [Spanish] El magnetismo residual es un fenomeno en el que los dipolos magneticos de una sustancia se encuentran orientados en un grado determinado. Por otro lado, cuando existen fuerzas internas capaces de alinear los dipolos magneticos elementales de un material, se tiene un iman permanente. Al igual que en un conductor o un material, en los elementos de una maquina electrica rotatoria se pueden inducir campos magneticos que producen un magnetismo residual o magnetizacion. En las maquinas electricas rotatorias, el fenomeno de magnetizacion causa graves problemas, como la generacion de corrientes inducidas que propician el desgaste mecanico

Residues of cypermethrin and endosulfan in soils of Swat valley

Directory of Open Access Journals (Sweden)

M. Nafees

2009-05-01

Full Text Available Swat Valley was studied for two widely used pesticides; cypermethrin and endosulfan. A total of 63 soil samples were collected from 27 villages selected for this purpose. The collected soil samples were extracted with n-hexane, pesticides were separated, identified and quantified by a GC-ECD system. Endosulfan was 0.24 - 1.51 mg kg-1 and 0.13 - 12.67 mg kg-1 in rainfed and irrigated areas, respectively. The residual level of cypermethrin was comparatively high with a level of0.14 to 27.62 mg kg-1 and 0.05 to 73.75 mg kg-1 in rainfed and irrigated areas, respectively. For assessing the possible causes of pesticide residues in soil, 360 farmers were interviewed. It was found that both, cypermethrin and endosulfan, apart from agriculture were also widely misused for fishing in the entire stretch of River Swat and its tributaries. River Swat is used for irrigation in Swat Valley and this wide misuse of pesticides can also contribute to pesticide residue in soil.

Production of surfactin from rice mill polishing residue by submerged fermentation using Bacillus subtilis MTCC 2423.

Science.gov (United States)

Gurjar, Jigar; Sengupta, Bina

2015-08-01

Rice mill polishing residue (RMPR), an abundant and cheap agro residue, was used as substrate for microbial growth of Bacillus subtilis MTCC 2423 by submerged fermentation process to produce surfactin. Nutrients present in the residue were sufficient to sustain the growth of the microorganism. Multi stage foam fractionation followed by acid precipitation was used to concentrate and recover the product. Recoverable yield of surfactin was 4.17 g/kg residue. Product recovered in the foamate accounted for 69% of the total yield. The residual broth containing ∼ 30% surfactin exhibited biological oxygen demand and chemical oxygen demand values of 23 and 69 mg/L respectively. The microbial growth data was correlated using three parameter sigmoid models. Surfactin synthesized had a predominance of molecular weight 1076 Da. Foam separation of copper using surfactin resulted in a maximum removal of 72.5%. Copyright © 2015 Elsevier Ltd. All rights reserved.

Influence of MSD crack pattern on the residual strength of flat stiffened sheets

Science.gov (United States)

Nilsson, K.-F.

A parameter study of the residual strength for a multiple site damaged (MSD) stiffened sheet is presented. The analysis is based on an elastic-plastic fracture analysis using the yield-strip model for interaction between a lead crack and the smaller MSD cracks. Two crack growth criteria, one with a pronounced crack growth resistance and one with no crack growth resistance and five different MSD crack patterns, are analysed for different sizes of the lead crack and the smaller MSD cracks. The analysis indicates that the residual strength reduction depends on all these parameters and that MSD may totally erode the crack arrest capability of a tear strap. Another important outcome is that for certain combinations also very small MSD cracks may induce a significant residual strength reduction.

Volatile compounds and some physico-chemical properties of pastırma produced with different nitrate levels

Directory of Open Access Journals (Sweden)

Ahmet Akköse

2017-08-01

Full Text Available Objective The aim of the study was to evaluate the effects of different nitrate levels (150, 300, 450, and 600 ppm KNO3 on the volatile compounds and some other properties of pastırma. Methods Pastırma samples were produced under the controlled condition and analyses of volatile compounds, and thiobarbituric acid reactive substances (TBARS as an indicator of lipid oxidation, non-protein nitrogenous matter content as an indicator of proteolysis, color and residual nitrite were carried out on the final product. The profile of volatile compounds of pastırma samples was analyzed by gas chromatography/mass spectrometry using a solid phase microextraction. Results Nitrate level had a significant effect on pH value (p<0.05 and a very significant effect on TBARS value (p<0.01. No significant differences were determined in terms of aw value, non-protein nitrogenous substance content, color and residual nitrite between pastırma groups produced by using different nitrate levels. Nitrate level had a significant (p<0.05 or a very significant (p<0.01 effect on some volatile compounds. It was determined that the amounts and counts of volatile compounds were lower in the 450 and especially 600 ppm nitrate levels than 150 and 300 ppm nitrate levels (p<0.05. While the use of 600 ppm nitrate did not cause an increase in residual nitrite levels, the use of 150 ppm nitrate did not negatively affect the color of pastırma. However, the levels of volatile compounds decreased with an increasing level of nitrate. Conclusion The use of 600 ppm nitrate is not a risk in terms of residual nitrite in pastırma produced under controlled condition, however, this level is not suitable due to decrease in the amount of volatile compounds.

Risk of DDT residue in maize consumed by infants as complementary diet in southwest Ethiopia.

Science.gov (United States)

Mekonen, Seblework; Lachat, Carl; Ambelu, Argaw; Steurbaut, Walter; Kolsteren, Patrick; Jacxsens, Liesbeth; Wondafrash, Mekitie; Houbraken, Michael; Spanoghe, Pieter

2015-04-01

Infants in Ethiopia are consuming food items such as maize as a complementary diet. However, this may expose infants to toxic contaminants like DDT. Maize samples were collected from the households visited during a consumption survey and from markets in Jimma zone, southwestern Ethiopia. The residues of total DDT and its metabolites were analyzed using the Quick, Easy, Cheap, Effective, Rugged and Safe (QuEChERS) method combined with dispersive solid phase extraction cleanup (d-SPE). Deterministic and probabilistic methods of analysis were applied to determine the consumer exposure of infants to total DDT. The results from the exposure assessment were compared with the health based guidance value in this case the provisional tolerable daily intake (PTDI). All maize samples (n=127) were contaminated by DDT, with a mean concentration of 1.770 mg/kg, which was far above the maximum residue limit (MRL). The mean and 97.5 percentile (P 97.5) estimated daily intake of total DDT for consumers were respectively 0.011 and 0.309 mg/kg bw/day for deterministic and 0.011 and 0.083 mg/kg bw/day for probabilistic exposure assessment. For total infant population (consumers and non-consumers), the 97.5 percentile estimated daily intake were 0.265 and 0.032 mg/kg bw/day from the deterministic and probabilistic exposure assessments, respectively. Health risk estimation revealed that, the mean and 97.5 percentile for consumers, and 97.5 percentile estimated daily intake of total DDT for total population were above the PTDI. Therefore, in Ethiopia, the use of maize as complementary food for infants may pose a health risk due to DDT residue. Copyright © 2014 Elsevier B.V. All rights reserved.

76 FR 53372 - Receipt of Several Pesticide Petitions Filed for Residues of Pesticide Chemicals in or on Various...

Science.gov (United States)

2011-08-26

... at 0.2 ppm; poultry, fat at 0.2 ppm; poultry, meat at 0.06 ppm; and poultry, meat byproducts at 0.06... all appropriate agricultural commodities and respective processing fractions. The LOQ of flumioxazin..., Feed additives, Food additives, Pesticides and pests, Reporting and recordkeeping requirements. Dated...

An estimation of cogeneration potential by using refinery residuals in Mexico

International Nuclear Information System (INIS)

Marin-Sanchez, J.E.; Rodriguez-Toral, M.A.

2007-01-01

Electric power generation in Mexico is mainly based on fossil fuels, specifically heavy fuel oil, although the use of natural gas combined cycles (NGCC) is becoming increasingly important. This is the main destination that has promoted growing imports of natural gas, currently accounting for about 20% of the total national annual consumption. Available crude oil is becoming heavier; thus refineries should be able to process it, and to handle greater quantities of refinery residuals. If all refinery residuals are used in cogeneration plants serving petroleum refineries, the high heat/power ratio of refinery needs, leads to the availability of appreciable quantities of electricity that can be exported to the public utility. Thus, in a global perspective, Mexican imports of natural gas may be reduced by cogeneration using refinery residuals. This is not the authors' idea; in fact, PEMEX, the national oil company, has been entitled by the Mexican congress to sell its power leftovers to The Federal Electricity Commission (CFE) in order to use cogeneration in the way described for the years to come. A systematic way of determining the cogeneration potential by using refinery residuals from Mexican refineries is presented here, taking into account residual quantities and composition, from a national perspective, considering expected scenarios for Maya crude content going to local refineries in the years to come. Among different available technologies for cogeneration using refinery residuals, it is believed that the integrated gasification combined cycle (IGCC) would be the best option. Thus, considering IGCC plants supplying heat and power to refineries where it is projected to have refinery residuals for cogeneration, the expected electric power that can be sent to the public utility is quantified, along with the natural gas imports mitigation that may be attained. This in turn would contribute to a necessary fuel diversification policy balancing energy, economy and

Heavy metal residues in beef carcasses in Beni-Suef abattoir, Egypt

Directory of Open Access Journals (Sweden)

Fathy A. Khalafalla

2011-09-01

Full Text Available A total of 300 samples were collected from cattle slaughtered in the Beni-Suef abattoir in Egypt. Samples included muscle, liver and kidney. Animals were randomly selected from the slaughter line. The age of the slaughtered cattle was less than three years (18-30 months. Samples were packed separately in plastic bags, identified and stored at -18°C until analysis which was performed at the Max Rubner Institute in Kulmbach, Germany, for the following heavy metals residues: lead, cadmium, mercury, arsenic, chromium and nickel in beef muscle, liver and kidney samples. The results revealed that the overall mean residual levels of lead were 8.77 µg/kg, 42.70 µg/kg and 109.42 µg/kg fresh weight in muscle, liver and kidney samples, respectively, while the mean residual levels of cadmium were 1.40 µg/kg, 14.16 µg/kg and 62.56 µg/kg fresh weight, respectively, and the mean arsenic residual levels were 5.06 µg/kg, 4.64 µg/kg and 14.92 µg/kg fresh weight, respectively. The mean residual levels of mercury were 3.91 µg/kg, 5.81 µg/kg and 10.14 µg/kg fresh weight, respectively, and the residual levels of chromium were 11.20 µg/kg, 21.85 µg/kg and 25.49 µg/kg fresh weight, respectively. Finally, the mean residual levels of nickel were 21.17 µg/kg, 14.59 µg/kg and 34.95 µg/kg fresh weight, respectively. The mean values of all heavy metals examined were low and did not exceed the permissible limits adopted by different organisations. Most heavy metals accumulated in higher concentrations in the kidney in comparison to the liver and muscle.

The potential of agro-industrial residues and municipal solid waste for production of biogas and electricity in Tanzania

Energy Technology Data Exchange (ETDEWEB)

Kivaisi, A K [Univ. of Dar es Salaam, Botany Dept., Applied Microbiology Unit (Tanzania, United Republic of)

1998-12-31

This paper gives an overview of the energy demands in Tanzania, and highlights the current serious shortage of electricity. Government strategy to alleviate the problem include exploitation of the country`s big natural gas reserves for power generation, and utilization of the renewable energies such as solar, wind and biogas. Important agro-industrial residues and municipal solid wastes with large potentials for anaerobic converstion into biogas and electricity have been identified and quantified. Tanzania is estimated to generate about 615,000 organic matter from coffee, sisal, sugar and cereal residues and households in main towns are estimated to generate about 600,000 tons of organic matter annually. Laboratory scale determinations of methane yields from the residues gave 400 m{sup 3} CH{sub 4}/ton VS of sisal pulp; 400 m{sup 3} CH{sub 4}/ton VS of sisal production wastewater; 400 m{sup 3} CH{sub 4}/ton VS of Robusta coffee solid waste, 350 m{sup 3} CH{sub 4}/ton VS of sugar processing wastewater; 250 m{sup 3} CH{sub 4}/ton VS of sugar filter mat, 450 m{sup 3} CH{sub 4}/ton VS maize bran and 300 m{sup 3} CH{sub 4}/ton VS of mixed household waste. Based on these results the estimated total annual potential electricity production from these residues is 1.4 million MW. The total oil substitution from these residues has been estimated at 0.35 million tonnes crude diesel oil per annum equivalent to 2% of the total energy consumption in Tanzania. Case studies onthe coffee and sisal processing factories indicate that exploitation of the residues for the production of electricity on site these factories is feasible. Utilization of agro-industrial residues and municipal waste for biogas production has enormous potential for reduction of environmental pollution. The potential substitution of fossil fuel with biogas represents an annual reduction in the net CO{sub 2} emission to the atmosphere of approximately 1.3 million tonnes. By treating the residues in controlled

The potential of agro-industrial residues and municipal solid waste for production of biogas and electricity in Tanzania

Energy Technology Data Exchange (ETDEWEB)

Kivaisi, A.K. [Univ. of Dar es Salaam, Botany Dept., Applied Microbiology Unit (Tanzania, United Republic of)

1997-12-31

This paper gives an overview of the energy demands in Tanzania, and highlights the current serious shortage of electricity. Government strategy to alleviate the problem include exploitation of the country`s big natural gas reserves for power generation, and utilization of the renewable energies such as solar, wind and biogas. Important agro-industrial residues and municipal solid wastes with large potentials for anaerobic converstion into biogas and electricity have been identified and quantified. Tanzania is estimated to generate about 615,000 organic matter from coffee, sisal, sugar and cereal residues and households in main towns are estimated to generate about 600,000 tons of organic matter annually. Laboratory scale determinations of methane yields from the residues gave 400 m{sup 3} CH{sub 4}/ton VS of sisal pulp; 400 m{sup 3} CH{sub 4}/ton VS of sisal production wastewater; 400 m{sup 3} CH{sub 4}/ton VS of Robusta coffee solid waste, 350 m{sup 3} CH{sub 4}/ton VS of sugar processing wastewater; 250 m{sup 3} CH{sub 4}/ton VS of sugar filter mat, 450 m{sup 3} CH{sub 4}/ton VS maize bran and 300 m{sup 3} CH{sub 4}/ton VS of mixed household waste. Based on these results the estimated total annual potential electricity production from these residues is 1.4 million MW. The total oil substitution from these residues has been estimated at 0.35 million tonnes crude diesel oil per annum equivalent to 2% of the total energy consumption in Tanzania. Case studies onthe coffee and sisal processing factories indicate that exploitation of the residues for the production of electricity on site these factories is feasible. Utilization of agro-industrial residues and municipal waste for biogas production has enormous potential for reduction of environmental pollution. The potential substitution of fossil fuel with biogas represents an annual reduction in the net CO{sub 2} emission to the atmosphere of approximately 1.3 million tonnes. By treating the residues in controlled