Triphenylmethane, a possible moderator material

International Nuclear Information System (INIS)

Hügle, Th.; Mocko, M.; Hartl, M.A.; Daemen, L.L.; Muhrer, G.

2014-01-01

New challenges in neutron scattering result in an increased demand in novel moderator concepts. The most direct way to address the problem would be to change the moderator material itself. However the range of available neutron moderator materials is small. In this paper, we discuss triphenylmethane, a possible moderator material especially promising for cold neutron moderator applications. Our investigations include a parallel experimental and theoretical approach ranging from cross-section measurements and inelastic neutron spectroscopy to molecular modeling. -- Highlights: • Triphenylmethane as a potential moderator material is discussed. • Parallel theoretical and experimental approach. • Possibly very useful for cold neutrons

Analysis of explosion-induced releases of toxic materials at an environmental restoration project

International Nuclear Information System (INIS)

Bloom, S.G.; Moon, W.H. Jr.

1993-01-01

Prior to 1988, a variety of materials were buried on the US DOE Oak Ridge Reservation. Records of the disposal operations are incomplete and toxic materials may have been placed adjacent to potential explosives. One of the safety concerns in conducting an environmental restoration project at the burial sites, is the possibility of an explosion which could release toxic materials to the atmosphere. A safety analysis examined the consequences of such releases by first postulating an upper bound for the strength of an explosive. A correlation, developed by Steindler and Seefeldt of Argonne National Laboratory, was then used to estimate the amount and particle-size distribution of the material that could become airborne from the explosion. The estimated amount of airborne material was the source term in an atmospheric dispersion model which was used to calculate infinite-time, concentration-time integrals and 5-minute, time- weighted average concentrations at locations down-wind from the explosion. The dispersion model includes particle deposition as a function of particle-size distribution class. The concentration-time integrals and average concentrations were compared to published guidelines to assess the consequences of an accidental explosion

Characterization of new functionalized calcium carbonate-polycaprolactone composite material for application in geometry-constrained drug release formulation development.

Science.gov (United States)

Wagner-Hattler, Leonie; Schoelkopf, Joachim; Huwyler, Jörg; Puchkov, Maxim

2017-10-01

A new mineral-polymer composite (FCC-PCL) performance was assessed to produce complex geometries to aid in development of controlled release tablet formulations. The mechanical characteristics of a developed material such as compactibility, compressibility and elastoplastic deformation were measured. The results and comparative analysis versus other common excipients suggest efficient formation of a complex, stable and impermeable geometries for constrained drug release modifications under compression. The performance of the proposed composite material has been tested by compacting it into a geometrically altered tablet (Tablet-In-Cup, TIC) and the drug release was compared to commercially available product. The TIC device exhibited a uniform surface, showed high physical stability, and showed absence of friability. FCC-PCL composite had good binding properties and good compactibility. It was possible to reveal an enhanced plasticity characteristic of a new material which was not present in the individual components. The presented FCC-PCL composite mixture has the potential to become a successful tool to formulate controlled-release dosage solid forms.

Radioactive materials released from nuclear power plants (1976)

International Nuclear Information System (INIS)

Decker, T.R.

1978-11-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1976 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1976 release data are compared with previous year releases in tabular form. Data covering specific radionuclides are summarized

Radioactive materials released from nuclear power plants

International Nuclear Information System (INIS)

Tichler, J.; Norden, K.; Congemi, J.

1991-05-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1988 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1988 release data are summarized in tabular form. Data covering specific radionuclides are summarized. 16 tabs

Inclusion of cefalexin in SBA-15 mesoporus material and release property

International Nuclear Information System (INIS)

Zhai, Qing-Zhou

2012-01-01

SBA-15 (Santa Barbara Amorphous-15) is a high ordered mesoporous material. It has the advantages of a non-toxic property, good hydrothermal stability and thermal stability, etc. Inside inner surface a lot of silanols exist. Pore diameter size is uniform and pore size distribution is narrow. This structural feature makes SBA-15 have a higher loading drug amount and be able to effectively extend the drug release cycle. In this paper, polyethylene glycol-block-polypropylene glycol-block-polyethylene glycol was used as template and tetraethyl orthosilicate was used as silica source to prepare SBA-15 by hydrothermal synthesis method. Cefalexin was included in SBA-15 and the included cefalexin drug content was 158.72 mg/g. The composite materials were characterized by using chemical analysis, powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), infrared (IR) spectroscopy, and low temperature nitrogen adsorption–desorption. The results showed that cefalexin had been successfully included in host SBA-15 pore channels. Rational analyses of the release processes of cefalexin drug from the pores of SBA-15 to the simulated body fluid, simulated gastric juice and simulated intestinal fluid were made and sustained-release effects of the drug in complex system were studied. The results showed that in simulated body fluid within 1–5 h cefalexin was fast released and the cumulative release reached 50.00% at 5 h. In 15–20 h, the sustained release speed of cefalexin drug in the composite material decreased and the sustained-release cumulative amount reached 99.87% at 20 h. The release of cefalexin was basically complete. In simulated gastric fluid, composite material sustained-release ended at 4 h, the cumulative sustained release ratio reaching 26.10%. In simulated gastric fluid, the sustained-release was complete at 7 h, the cumulative sustained release ratio reaching 32.46%. The composite material of SBA-15 and cefalexin

Assessment of consequences from airborne releases of radioactive material

International Nuclear Information System (INIS)

McGrath, P.E.; Blond, R.M.

1976-01-01

Over the past several years, the manner in which assessments have been made of the consequences of large airborne releases of radioactive material has not changed much conceptually. The models to describe the atmospheric dispersion of the radioactive material have generally been time-invariant, i.e., the meteorological conditions (thermal stability, wind speed, and precipitation) are invariant during release and the subsequent period of radiation exposure of the population to the airborne material. The frequency distribution of the meteorological conditions are determined by analyzing several years of weather data from the appropriate geographical location. In reality, weather is continuously changing over short time periods (hours) following the release. It is to be expected that the changing meteorological conditions would have important effects on the potential consequences of the release. A time-dependent atmospheric dispersion model was developed and implemented in the Reactor Safety Study. This paper provides a description of the model and the nature of the results generated. Emphasis is given to an explanation of how, and why, these results differ from those estimated with time-invariant models

Influence of factors on release of antimicrobials from antimicrobial packaging materials.

Science.gov (United States)

Wu, Yu-Mei; Wang, Zhi-Wei; Hu, Chang-Ying; Nerín, Cristina

2018-05-03

Antimicrobial packaging materials (films or coatings) (APMs) have aroused great interest among the scientists or the experts specialized in material science, food science, packaging engineering, biology and chemistry. APMs have been used to package the food, such as dairy products, poultry, meat (e.g., beef), salmon muscle, pastry dough, fresh pasta, bakery products, fruits, vegetables and beverages. Some materials have been already commercialized. The ability of APMs to extend the shelf-life of the food depends on the release rate of the antimicrobials (AMs) from the materials to the food. The optimum rate is defined as target release rate (TRR). To achieve TRR, the influencing factors of the release rate should be considered. Herein we reviewed for the first time these factors and their influence on the release. These factors mainly include the AMs, food (or food simulant), packaging materials, the interactions among them, the temperature and environmental relative humidity (RH).

Review on fluoride-releasing restorative materials--fluoride release and uptake characteristics, antibacterial activity and influence on caries formation.

Science.gov (United States)

Wiegand, Annette; Buchalla, Wolfgang; Attin, Thomas

2007-03-01

The purpose of this article was to review the fluoride release and recharge capabilities, and antibacterial properties, of fluoride-releasing dental restoratives, and discuss the current status concerning the prevention or inhibition of caries development and progression. Information from original scientific full papers or reviews listed in PubMed (search term: fluoride release AND (restorative OR glass-ionomer OR compomer OR polyacid-modified composite resin OR composite OR amalgam)), published from 1980 to 2004, was included in the review. Papers dealing with endodontic or orthodontic topics were not taken into consideration. Clinical studies concerning secondary caries development were only included when performed in split-mouth design with an observation period of at least three years. Fluoride-containing dental materials show clear differences in the fluoride release and uptake characteristics. Short- and long-term fluoride releases from restoratives are related to their matrices, setting mechanisms and fluoride content and depend on several environmental conditions. Fluoride-releasing materials may act as a fluoride reservoir and may increase the fluoride level in saliva, plaque and dental hard tissues. However, clinical studies exhibited conflicting data as to whether or not these materials significantly prevent or inhibit secondary caries and affect the growth of caries-associated bacteria compared to non-fluoridated restoratives. Fluoride release and uptake characteristics depend on the matrices, fillers and fluoride content as well as on the setting mechanisms and environmental conditions of the restoratives. Fluoride-releasing materials, predominantly glass-ionomers and compomers, did show cariostatic properties and may affect bacterial metabolism under simulated cariogenic conditions in vitro. However, it is not proven by prospective clinical studies whether the incidence of secondary caries can be significantly reduced by the fluoride release of

Sulfur Release from Cement Raw Materials during Solid Fuel Combustion

DEFF Research Database (Denmark)

Nielsen, Anders Rooma; Larsen, Morten B.; Glarborg, Peter

2011-01-01

During combustion of solid fuels in the material inlet end of cement rotary kilns, local reducing conditions can occur and cause decomposition of sulfates from cement raw materials. Decomposition of sulfates is problematic because it increases the gas-phase SO2 concentration, which may cause...... deposit formation in the kiln system. SO2 release from cement raw materials during combustion of solid fuels has been studied experimentally in a high temperature rotary drum. The fuels were tire rubber, pine wood, petcoke, sewage sludge, and polypropylene. The SO2 release from the raw materials...

Evaluation of hydrophobic materials as matrices for controlled-release drug delivery.

Science.gov (United States)

Quadir, Mohiuddin Abdul; Rahman, M Sharifur; Karim, M Ziaul; Akter, Sanjida; Awkat, M Talat Bin; Reza, Md Selim

2003-07-01

The present study was undertaken to evaluate the effect of different insoluble and erodable wax-lipid based materials and their content level on the release profile of drug from matrix systems. Matrix tablets of theophylline were prepared using carnauba wax, bees wax, stearic acid, cetyl alcohol, cetostearyl alcohol and glyceryl monostearate as rate-retarding agents by direct compression process. The release of theophylline from these hydrophobic matrices was studied over 8-hours in buffer media of pH 6.8. Statistically significant difference was found among the drug release profile from different matrices. The release kinetics was found to be governed by the type and content of hydrophobic materials in the matrix. At lower level of wax matrices (25%), a potential burst release was observed with all the materials being studied. Bees wax could not exert any sustaining action while an extensive burst release was found with carnauba wax at this hydrophobic load. Increasing the concentration of fat-wax materials significantly decreased the burst effect of drug from the matrix. At higher hydrophobic level (50% of the matrix), the rate and extent of drug release was significantly reduced due to increased tortuosity and reduced porosity of the matrix. Cetostearyl alcohol imparted the strongest retardation of drug release irrespective of fat-wax level. Numerical fits indicate that the Higuchi square root of time model was the most appropriate one for describing the release profile of theophylline from hydrophobic matrices. The release mechanism was also explored and explained with biexponential equation. Application of this model indicates that Fickian or case I kinetics is the predominant mechanism of drug release from these wax-lipid matrices. The mean dissolution time (MDT) was calculated for all the formulations and the highest MDT value was obtained with cetostearyl matrix. The greater sustaining activity of cetostearyl alcohol can be attributed to some level of

Model for absorption and release of gaseous materials by forest canopies

International Nuclear Information System (INIS)

Murphy, C.E. Jr.

1976-01-01

A model of the physical processes defining the absorption and release of materials by a forest canopy has been developed. The model deals with the turbulent transport of gaseous materials in the surface boundary layer near the canopy, the turbulent transport in the canopy atmosphere, the transport through the boundary layer near the leaf and soil surface, and the solution of the gaseous materials in intracellular fluids and subsequent diffusion into the leaf cells. The model is used to simulate the uptake of molecular tritium by the forest canopy and the subsequent release of tritiated water. Results of dynamic simulations of tritium uptake and release are compared with data collected at the time of a release of molecular tritium to the atmosphere

Stimuli-Responsive Materials for Controlled Release Applications

KAUST Repository

Li, Song

2015-01-01

The controlled release of therapeutics has been one of the major challenges for scientists and engineers during the past three decades. To address this outstanding problem, the design and fabrication of stimuli-responsive materials are pursued

Releasing growth factors from activated human platelets after chitosan stimulation: a possible bio-material for platelet-rich plasma preparation.

Science.gov (United States)

Shen, E-Chin; Chou, Tz-Chong; Gau, Ching-Hwa; Tu, Hsiao-Pei; Chen, Yen-Teen; Fu, Earl

2006-10-01

Thrombin is commonly used for activating the platelets and releasing the growth factors on the application of platelet-rich plasma (PRP). We have previously reported that chitosan can enhance rabbit platelet aggregation. In this study, the effects of chitosan on the subsequent growth factors release after human platelets activation were examined to evaluate the possibility of chitosan being used as a substitute for thrombin during PRP preparation. Human platelet activation was determined by aggregation, adhesion and alpha-granule membrane glycoprotein expression. Platelet aggregation was measured by the turbidimetric method, the adhesion was directly examined on chitosan-coated glass plates under light microscope and scanning electron microscope (SEM), and the alpha-granule membrane glycoprotein was detected by fluorescent isothiocyanate (FITC)-conjugated anti-CD61 antibody through flow cytometry. The subsequent epidermal growth factor (EGF), platelet-derived growth factor (PDGF)-AB and transforming growth factor (TGF)-beta1 release from platelets were assayed by ELISA after mixing with chitosan. The enhancing effects on the platelet adhesion and the aggregation from chitosan were observed. Under both microscopes, the adhesive platelets on the chitosan-coated plates were not only greater in number but also earlier in activation than those on the control plates. With flow cytometry, increased glycoprotein IIIa expression in platelets was detected after chitosan treatment. Greater concentrations of growth factors were measured from PRP after chitosan treatment than after the solvent treatment. Because of the observations of growth factors releasing from activated human platelets after chitosan stimulation, we suggest that chitosan may be an appropriate substitute for thrombin in PRP preparation.

Enantioselectively controlled release of chiral drug (metoprolol) using chiral mesoporous silica materials

Energy Technology Data Exchange (ETDEWEB)

Guo Zhen; Liu Xianbin; Ng, Siu-Choon; Chen Yuan; Yang Yanhui [School of Chemical and Biomedical Engineering, Nanyang Technological University, Singapore 637459 (Singapore); Du Yu, E-mail: du_yu@jlu.edu.cn, E-mail: yhyang@ntu.edu.sg [College of Electronic Science and Engineering, Jilin University, Changchun 130012 (China)

2010-04-23

Chiral porous materials have attracted burgeoning attention on account of their potential applications in many areas, such as enantioseparation, chiral catalysis, chemical sensors and drug delivery. In this report, chiral mesoporous silica (CMS) materials with various pore sizes and structures were prepared using conventional achiral templates (other than chiral surfactant) and a chiral cobalt complex as co-template. The synthesized CMS materials were characterized by x-ray diffraction, nitrogen physisorption, scanning electron microscope and transmission electron microscope. These CMS materials, as carriers, were demonstrated to be able to control the enantioselective release of a representative chiral drug (metoprolol). The release kinetics, as modeled by the power law equation, suggested that the release profiles of metoprolol were remarkably dependent on the pore diameter and pore structure of CMS materials. More importantly, R- and S-enantiomers of metoprolol exhibited different release kinetics on CMS compared to the corresponding achiral mesoporous silica (ACMS), attributable to the existence of local chirality on the pore wall surface of CMS materials. The chirality of CMS materials on a molecular level was further substantiated by vibrational circular dichroism measurements.

Enantioselectively controlled release of chiral drug (metoprolol) using chiral mesoporous silica materials

International Nuclear Information System (INIS)

Guo Zhen; Liu Xianbin; Ng, Siu-Choon; Chen Yuan; Yang Yanhui; Du Yu

2010-01-01

Chiral porous materials have attracted burgeoning attention on account of their potential applications in many areas, such as enantioseparation, chiral catalysis, chemical sensors and drug delivery. In this report, chiral mesoporous silica (CMS) materials with various pore sizes and structures were prepared using conventional achiral templates (other than chiral surfactant) and a chiral cobalt complex as co-template. The synthesized CMS materials were characterized by x-ray diffraction, nitrogen physisorption, scanning electron microscope and transmission electron microscope. These CMS materials, as carriers, were demonstrated to be able to control the enantioselective release of a representative chiral drug (metoprolol). The release kinetics, as modeled by the power law equation, suggested that the release profiles of metoprolol were remarkably dependent on the pore diameter and pore structure of CMS materials. More importantly, R- and S-enantiomers of metoprolol exhibited different release kinetics on CMS compared to the corresponding achiral mesoporous silica (ACMS), attributable to the existence of local chirality on the pore wall surface of CMS materials. The chirality of CMS materials on a molecular level was further substantiated by vibrational circular dichroism measurements.

Methodology for performing measurements to release material from radiological control

International Nuclear Information System (INIS)

Durham, J.S.; Gardner, D.L.

1993-09-01

This report describes the existing and proposed methodologies for performing measurements of contamination prior to releasing material for uncontrolled use at the Hanford Site. The technical basis for the proposed methodology, a modification to the existing contamination survey protocol, is also described. The modified methodology, which includes a large-area swipe followed by a statistical survey, can be used to survey material that is unlikely to be contaminated for release to controlled and uncontrolled areas. The material evaluation procedure that is used to determine the likelihood of contamination is also described

Methodology for prediction and estimation of consequences of possible atmospheric releases of hazardous matter: 'Kursk' submarine study

Directory of Open Access Journals (Sweden)

A. Baklanov

2003-01-01

Full Text Available There are objects with some periods of higher than normal levels of risk of accidental atmospheric releases (nuclear, chemical, biological, etc.. Such accidents or events may occur due to natural hazards, human errors, terror acts, and during transportation of waste or various operations at high risk. A methodology for risk assessment is suggested and it includes two approaches: 1 probabilistic analysis of possible atmospheric transport patterns using long-term trajectory and dispersion modelling, and 2 forecast and evaluation of possible contamination and consequences for the environment and population using operational dispersion modelling. The first approach could be applied during the preparation stage, and the second - during the operation stage. The suggested methodology is applied on an example of the most important phases (lifting, transportation, and decommissioning of the ``Kursk" nuclear submarine operation. It is found that the temporal variability of several probabilistic indicators (fast transport probability fields, maximum reaching distance, maximum possible impact zone, and average integral concentration of 137Cs showed that the fall of 2001 was the most appropriate time for the beginning of the operation. These indicators allowed to identify the hypothetically impacted geographical regions and territories. In cases of atmospheric transport toward the most populated areas, the forecasts of possible consequences during phases of the high and medium potential risk levels based on a unit hypothetical release (e.g. 1 Bq are performed. The analysis showed that the possible deposition fractions of 10-11 (Bq/m2 over the Kola Peninsula, and 10-12 - 10-13 (Bq/m2 for the remote areas of the Scandinavia and Northwest Russia could be observed. The suggested methodology may be used successfully for any potentially dangerous object involving risk of atmospheric release of hazardous materials of nuclear, chemical or biological nature.

Methodology for prediction and estimation of consequences of possible atmospheric releases of hazardous matter: "Kursk"? submarine study

Science.gov (United States)

Baklanov, A.; Mahura, A.; Sørensen, J. H.

2003-03-01

There are objects with some periods of higher than normal levels of risk of accidental atmospheric releases (nuclear, chemical, biological, etc.). Such accidents or events may occur due to natural hazards, human errors, terror acts, and during transportation of waste or various operations at high risk. A methodology for risk assessment is suggested and it includes two approaches: 1) probabilistic analysis of possible atmospheric transport patterns using long-term trajectory and dispersion modelling, and 2) forecast and evaluation of possible contamination and consequences for the environment and population using operational dispersion modelling. The first approach could be applied during the preparation stage, and the second - during the operation stage. The suggested methodology is applied on an example of the most important phases (lifting, transportation, and decommissioning) of the "Kursk" nuclear submarine operation. It is found that the temporal variability of several probabilistic indicators (fast transport probability fields, maximum reaching distance, maximum possible impact zone, and average integral concentration of 137Cs) showed that the fall of 2001 was the most appropriate time for the beginning of the operation. These indicators allowed to identify the hypothetically impacted geographical regions and territories. In cases of atmospheric transport toward the most populated areas, the forecasts of possible consequences during phases of the high and medium potential risk levels based on a unit hypothetical release are performed. The analysis showed that the possible deposition fractions of 1011 over the Kola Peninsula, and 10-12 - 10-13 for the remote areas of the Scandinavia and Northwest Russia could be observed. The suggested methodology may be used successfully for any potentially dangerous object involving risk of atmospheric release of hazardous materials of nuclear, chemical or biological nature.

Methodology for prediction and estimation of consequences of possible atmospheric releases of hazardous matter: "Kursk" submarine study

Science.gov (United States)

Baklanov, A.; Mahura, A.; Sørensen, J. H.

2003-06-01

There are objects with some periods of higher than normal levels of risk of accidental atmospheric releases (nuclear, chemical, biological, etc.). Such accidents or events may occur due to natural hazards, human errors, terror acts, and during transportation of waste or various operations at high risk. A methodology for risk assessment is suggested and it includes two approaches: 1) probabilistic analysis of possible atmospheric transport patterns using long-term trajectory and dispersion modelling, and 2) forecast and evaluation of possible contamination and consequences for the environment and population using operational dispersion modelling. The first approach could be applied during the preparation stage, and the second - during the operation stage. The suggested methodology is applied on an example of the most important phases (lifting, transportation, and decommissioning) of the ``Kursk" nuclear submarine operation. It is found that the temporal variability of several probabilistic indicators (fast transport probability fields, maximum reaching distance, maximum possible impact zone, and average integral concentration of 137Cs) showed that the fall of 2001 was the most appropriate time for the beginning of the operation. These indicators allowed to identify the hypothetically impacted geographical regions and territories. In cases of atmospheric transport toward the most populated areas, the forecasts of possible consequences during phases of the high and medium potential risk levels based on a unit hypothetical release (e.g. 1 Bq) are performed. The analysis showed that the possible deposition fractions of 10-11 (Bq/m2) over the Kola Peninsula, and 10-12 - 10-13 (Bq/m2) for the remote areas of the Scandinavia and Northwest Russia could be observed. The suggested methodology may be used successfully for any potentially dangerous object involving risk of atmospheric release of hazardous materials of nuclear, chemical or biological nature.

Natural and technologic hazardous material releases during and after natural disasters: a review.

Science.gov (United States)

Young, Stacy; Balluz, Lina; Malilay, Josephine

2004-04-25

Natural disasters may be powerful and prominent mechanisms of direct and indirect hazardous material (hazmat) releases. Hazardous materials that are released as the result of a technologic malfunction precipitated by a natural event are referred to as natural-technologic or na-tech events. Na-tech events pose unique environmental and human hazards. Disaster-associated hazardous material releases are of concern, given increases in population density and accelerating industrial development in areas subject to natural disasters. These trends increase the probability of catastrophic future disasters and the potential for mass human exposure to hazardous materials released during disasters. This systematic review summarizes direct and indirect disaster-associated releases, as well as environmental contamination and adverse human health effects that have resulted from natural disaster-related hazmat incidents. Thorough examination of historic disaster-related hazmat releases can be used to identify future threats and improve mitigation and prevention efforts.

Monitoring of the release of gaseous and aerosol-bound radioactive materials. Pt. 2

International Nuclear Information System (INIS)

1992-01-01

KTA 1503 contains requirements on technical installations and supplementary organizational measures considered necessary in order to monitor the release of gaseous and aerosol-bound radioactive materials. It consists of part 1: Monitoring of the release of radioactive materials together with stack gas during normal operation; part 2: Monitoring of the release of radioactive materials together with stack gas in the event of incidents; part 3: Monitoring of radioactive materials not released together with stack gas. The concept on which this rule is based is to ensure that in the case of incidents during which the result of effluent monitoring remains meaningful, such monitoring can be reliably performed. (orig./HSCH) [de

The release of lindane from contaminated building materials.

Science.gov (United States)

Volchek, Konstantin; Thouin, Geneviève; Kuang, Wenxing; Li, Ken; Tezel, F Handan; Brown, Carl E

2014-10-01

The release of the organochlorine pesticide lindane (γ-hexachlorocyclohexane) from several types of contaminated building materials was studied to assess inhalation hazard and decontamination requirements in response to accidental and/or intentional spills. The materials included glass, polypropylene carpet, latex-painted drywall, ceramic tiles, vinyl floor tiles, and gypsum ceiling tiles. For each surface concentration, an equilibrium concentration was determined in the vapour phase of the surrounding air. Vapor concentrations depended upon initial surface concentration, temperature, and type of building material. A time-weighted average (TWA) concentration in the air was used to quantify the health risk associated with the inhalation of lindane vapors. Transformation products of lindane, namely α-hexachlorocyclohexane and pentachlorocyclohexene, were detected in the vapour phase at both temperatures and for all of the test materials. Their formation was greater on glass and ceramic tiles, compared to other building materials. An empiric Sips isotherm model was employed to approximate experimental results and to estimate the release of lindane and its transformation products. This helped determine the extent of decontamination required to reduce the surface concentrations of lindane to the levels corresponding to vapor concentrations below TWA.

Response to a radioactive materials release having a transboundary impact

International Nuclear Information System (INIS)

1989-01-01

Compared with an accidental release of radioactive material which is confined to the accident State, a transboundary release has added dimensions which were not fully anticipated in publications dealing with response to accidents at nuclear facilities. The new aspects to the problem may be summarized as follows: (1) A transboundary release of radioactive material, as distinct from a release which affects only the accident State, has international repercussions in the following ways: Potentially at least, the difficulties associated with a transboundary release may be magnified in those States that have no nuclear facilities of their own and may, therefore, have foreseen no need for resources to assess and deal with radioactive contamination of their food supplies, their water and their environment appropriately. International trade, in food commodities particularly, may be severely affected. Issues of compensation may arise for which the dispute settlement mechanisms are weak or non-existent. (2) Many Member States are in such geographic locations that they could be affected by a transboundary release occurring in any of their surrounding neighbour States. Planning for and responding to such an event is necessarily more difficult than planning for an accidental release from a single, identified nuclear facility. (3) Deposits of radioactive material from a distant source are apt to be highly unpredictable. Depending on weather conditions, they may be localized in a random fashion or widespread. Because of the international dimension of the problem and its essentially unpredictable character it is recommended here that planning for such events should be carried at the national or federal government level rather than at provincial government level. 14 refs

Survey of radioactive effluent releases from byproduct material facilities. Technical report

International Nuclear Information System (INIS)

Cook, J.R.

1981-08-01

A survey of over 3,000 NRC byproduct material licensees was conducted in late 1980 to collect data on annual effluent releases of radioactivity. The survey was conducted through a questionnaire, which was sent to NRC licensees who handle radioactive material in unsealed form, i.e., research, medical, and industrial institutions. Principal findings from the survey analysis are as follows: More than 98% of the reported annual releases to air (484 to 490) yield calculated average concentrations at the boundary of the unrestricted area that were at 1% or less than the maximum permissible concentration (MPC) of Appendix B, Table II, Column 1 of 10 CFR 20. The largest reported annual release was estimated to yield a concentration that was approximately 12% of MPC, the 5 other releases ranged from 1 to 10% of MPC. All reported annual releases of liquid waste were within the limits specified by NRC with most facilities reporting annual releases of only a fraction of a curie. Based on the data provided by licensees and analyzed in this report, it appears that in general the environmental impacts from research, medical and industrial institutions and organizations licensed by the NRC to possess and use byproduct materials are minimal and correspond to a small fraction of that from natural background

Assessment of radioactive material released from a fuel fabrication plant under accidental conditions

International Nuclear Information System (INIS)

1981-01-01

This report evaluates the amounts of fissile material released both inside and outside a mixed oxide fuel fabrication plant (MOFFP) for light water reactors. The first section begins with a descriptive study of fissile material containment systems, and the methods available for quantifying accident occurrence probabilities. In addition to accidents common to all industrial facilities, other much rarer accidents were considered, such as aircraft crashes. The minimum occurrence probability limit for consideration in this study was set at 10 -6 per annum. The second part of this report attempts to assess the consequences of the accidents considered (i.e. with occurrence probabilities exceeding 10 -6 per annum) by determining maximum values for such accidents. Acts of sabotage and other accidents of this type are beyond the scope of this study and were not taken into consideration. The most serious potential accident would be a fire involving all of the glove boxes in the PuO 2 powder calcination and preparation cell, which could release 76.5 mg of PuO 2 powder into the atmosphere; the occurrence probability of such an accident, however, is slight (less than 10 -5 per annum). The second possibility, is a specially nuclear hazard that would release fission products into the atmosphere. The occurrence probability of such an accident is currently evaluated at 10 -3 per annum

Functionalized mesoporous materials for adsorption and release of different drug molecules: A comparative study

International Nuclear Information System (INIS)

Wang Gang; Otuonye, Amy N.; Blair, Elizabeth A.; Denton, Kelley; Tao Zhimin; Asefa, Tewodros

2009-01-01

The adsorption capacity and release properties of mesoporous materials for drug molecules can be improved by functionalizing their surfaces with judiciously chosen organic groups. Functionalized ordered mesoporous materials containing various types of organic groups via a co-condensation synthetic method from 15% organosilane and by post-grafting organosilanes onto a pre-made mesoporous silica were synthesized. Comparative studies of their adsorption and release properties for various model drug molecules were then conducted. Functional groups including 3-aminopropyl, 3-mercaptopropyl, vinyl, and secondary amine groups were used to functionalize the mesoporous materials while rhodamine 6G and ibuprofen were utilized to investigate the materials' relative adsorption and release properties. The self-assembly of the mesoporous materials was carried out in the presence of cetyltrimethylammonium bromide (CTAB) surfactant, which produced MCM-41 type materials with pore diameters of ∼2.7-3.3 nm and moderate to high surface areas up to ∼1000 m 2 /g. The different functional groups introduced into the materials dictated their adsorption capacity and release properties. While mercaptopropyl and vinyl functionalized samples showed high adsorption capacity for rhodamine 6G, amine functionalized samples exhibited higher adsorption capacity for ibuprofen. While the diffusional release of ibuprofen was fitted on the Fickian diffusion model, the release of rhodamine 6G followed Super Case-II transport model. - Graphical abstract: The adsorption capacity and release properties of mesoporous materials for various drug molecules are tuned by functionalizing the surfaces of the materials with judiciously chosen organic groups. This work reports comparative studies of the adsorption and release properties of functionalized ordered mesoporous materials containing different hydrophobic and hydrophilic groups that are synthesized via a co-condensation and post-grafting methods for

Reuse of conditional released materials from decommissioning; a review of approaches and scenarios with long-term constructions - 59149

International Nuclear Information System (INIS)

Daniska, Vladimir; Pritrsky, Jozef; Ondra, Frantisek; Zachar, Matej; Necas, Vladimir

2012-01-01

Paper presents the overall scope and actual results of the project for evaluation of representative scenarios for reuse of conditionally released materials from decommissioning. Aim of the project is to evaluate the possibilities of reuse of conditionally released steels and concrete in technical constructions which guarantee the long-term preservation of design properties over periods of 50-100 years. Interaction of conditionally released materials with public is limited and predictable due to design and purpose of selected constructions and due to fact that in many scenarios these materials are embedded in non-radioactive materials such as bars in reinforced concrete. Worker's scenarios for preparation, operation and maintenance of these constructions are analysed in detail including the manufacturing of elements for these constructions. Project aims to evaluate the scenarios of reuse of conditionally released materials in a complex way in order to develop the data for designers of scenarios and to evaluate the volumes of conditionally released materials based on facility (to be decommissioned) inventory data. The long-term constructions considered are bridges, tunnels, roads, railway constructions, industrial buildings, power industry equipment and others. Evaluation covers following areas: - Analysis of activities for manufacturing of reinforcement bars, rolled steel sheets and other steel elements and analysis of activities for construction of evaluated scenarios in order to evaluate the external exposure of professionals performing these activities; - Analysis of external exposure of professionals involved in operation and maintenance of the long-term constructions; analysis of external exposure of public groups which are exposed to evaluated constructions; - Analysis of internal exposure of public groups from the radionuclides released from the evaluated scenarios based on models for migration of radionuclides from the long-term constructions to critical

The release of lindane from contaminated building materials

OpenAIRE

Volchek, Konstantin; Thouin, Geneviève; Kuang, Wenxing; Li, Ken; Tezel, F. Handan; Brown, Carl E.

2014-01-01

The release of the organochlorine pesticide lindane (γ-hexachlorocyclohexane) from several types of contaminated building materials was studied to assess inhalation hazard and decontamination requirements in response to accidental and/or intentional spills. The materials included glass, polypropylene carpet, latex-painted drywall, ceramic tiles, vinyl floor tiles, and gypsum ceiling tiles. For each surface concentration, an equilibrium concentration was determined in the vapour phase of the s...

Resolving Radiological Classification and Release Issues for Many DOE Solid Wastes and Salvageable Materials

International Nuclear Information System (INIS)

Hochel, R.C.

1999-01-01

The cost effective radiological classification and disposal of solid materials with potential volume contamination, in accordance with applicable U.S. Department of Energy (DOE) Orders, suffers from an inability to unambiguously distinguish among transuranic waste, low-level waste, and unconditional-release materials. Depending on the classification, disposal costs can vary by a hundred-fold. But in many cases, the issues can be easily resolved by a combination of process information, some simple measurements, and calculational predictions from a computer model for radiation shielding.The proper classification and disposal of many solid wastes requires a measurement regime that is able to show compliance with a variety of institutional and regulatory contamination limits. Although this is not possible for all solid wastes, there are many that do lend themselves to such measures. Several examples are discussed which demonstrate the possibilities, including one which was successfully applied to bulk contamination.The only barriers to such broader uses are the slow-to-change institutional perceptions and procedures. For many issues and materials, the measurement tools are available; they need only be applied

Resolving Radiological Classification and Release Issues for Many DOE Solid Wastes and Salvageable Materials

Energy Technology Data Exchange (ETDEWEB)

Hochel, R.C.

1999-06-14

The cost effective radiological classification and disposal of solid materials with potential volume contamination, in accordance with applicable U.S. Department of Energy (DOE) Orders, suffers from an inability to unambiguously distinguish among transuranic waste, low-level waste, and unconditional-release materials. Depending on the classification, disposal costs can vary by a hundred-fold. But in many cases, the issues can be easily resolved by a combination of process information, some simple measurements, and calculational predictions from a computer model for radiation shielding.The proper classification and disposal of many solid wastes requires a measurement regime that is able to show compliance with a variety of institutional and regulatory contamination limits. Although this is not possible for all solid wastes, there are many that do lend themselves to such measures. Several examples are discussed which demonstrate the possibilities, including one which was successfully applied to bulk contamination.The only barriers to such broader uses are the slow-to-change institutional perceptions and procedures. For many issues and materials, the measurement tools are available; they need only be applied.

Radioactive materials released from nuclear power plants. Annual report 1977

International Nuclear Information System (INIS)

Decker, T.R.

1978-11-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1977 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1977 release data are compared with previous years releases in tabular form. Data covering specific radionuclides are summarized

Fluoride release and recharge abilities of contemporary fluoride-containing restorative materials and dental adhesives.

Science.gov (United States)

Dionysopoulos, Dimitrios; Koliniotou-Koumpia, Eugenia; Helvatzoglou-Antoniades, Maria; Kotsanos, Nikolaos

2013-01-01

The aim of this study was to evaluate the fluoride release of five fluoride-releasing restorative materials and three dental adhesives, before and after NaF solution treatment. Five restorative materials (Fuji IX GP, GC Corp.; Ketac N100, 3M ESPE; Dyract Extra, Dentsply; Beautifil II, Shofu Inc.; Wave, SDI) and three dental adhesives (Stae, SDI; Fluorobond II - Shofu Inc.; Prime & Bond NT, Dentsply) were investigated before and after NaF solution treatment. A fluoride ion-selective electrode was to measure fluoride concentrations. During the 86-day period before NaF solution treatment, Fuji IX GP released the highest amount of fluoride among the restorative materials while Prime & Bond NT was the highest among the dental adhesives. After NaF solution treatment, Fuji IX GP again ranked the highest in fluoride release among the restorative materials while Fluorobond II ranked the highest among dental adhesives. It was concluded that the compositions and setting mechanisms of fluoride-containing dental materials influenced their fluoride release and recharge abilities.

In Vitro Inhibition of Enamel Demineralisation by Fluoride-releasing Restorative Materials and Dental Adhesives.

Science.gov (United States)

Dionysopoulos, Dimitrios; Koliniotou-Koumpia, Eugenia; Helvatzoglou-Antoniades, Maria; Kotsanos, Nikolaos

2016-01-01

To determine the ability of 5 contemporary fluoride-releasing restoratives and 3 fluoride-releasing adhesives to inhibit enamel demineralisation surrounding restorations, and the associations between inhibition and the levels of fluoride released from these materials. Five fluoride-releasing restoratives (Fuji IX GP, Ketac N100, Dyract Extra, Beautifil II and Wave) and 3 fluoride-releasing adhesives (Stae, Prime & Bond NT and Fluoro Bond II) were investigated. Eight disks of each material were prepared. Fluoride release was measured daily using a fluoride-ion-selective electrode for 15 days. Twenty-four cavities for each group were restored with a restorative and an adhesive. Specimens were subjected to thermal stress and stored for 30 days in saline solution. After a 15-day pH-cycling regimen, two 150-μm-thick sections were derived from each specimen. Enamel lesion depth was measured at 0, 100, and 200 μm from each restoration's margin via polarised light microscopy. Of the restoratives investigated, Fuji IX GP released the most fluoride. The fluoride-releasing restoratives tested exhibited shallower enamel lesions than did the control group at all distances tested (p < 0.05). Fuji IX GP yielded significantly lower enamel lesion depth than did the other experimental materials. The depths of enamel lesions did not differ significantly when comparing restoratives applied with a fluoride-releasing adhesive with those applied with a non-fluoride-releasing adhesive. The fluoride-releasing materials tested reduced enamel demineralisation but to different extents, depending on their levels of fluoride release. Fluoride-releasing adhesives did not influence enamel lesion formation.

Determination of the long-term release of metal(loid)s from construction materials using DGTs.

Science.gov (United States)

Schmukat, A; Duester, L; Ecker, D; Heininger, P; Ternes, T A

2013-09-15

Long-term leaching experiments are crucial to estimate the potential release of dangerous substances from construction materials. The application of Diffuse Gradients in Thin film (DGT) in static-batch experiments was tested to study the long-term release of metal(loid)s from construction materials for hydraulic engineering, for half a year. Long-term release experiments are essential to improve calculations of the life-time release for this materials. DGTs in batch experiments were found to be a space and labour efficient application, which enabled (i) to study, in a non-invasive manner, the total release of nine metal(loid)s for half a year, (ii) to differentiate between release mechanisms and (iii) to study mechanisms which were contrary to the release or caused experimental artefacts in the batch experiments. For copper slag (test material) it was found that eight metal(loid)s were released over the whole time period of 184 d. Cu, Ni and Pb were found to be released, predominantly caused by (the) weathering of sulphide minerals. Only for Zn a surface depletion mechanism was identified. The results from the long-term batch experiments deliver new information on the release of metal(loid)s during the life cycle of construction materials with regard to river basin management objectives. Copyright © 2013 Elsevier B.V. All rights reserved.

Risk assessment methodology for evaluating releases of radioactively contaminated materials

International Nuclear Information System (INIS)

Chen, S.Y.

1993-01-01

Extensive decontamination and decommissioning (D ampersand D) activities are expected to be required in the near future in association with license termination of nuclear power facilities and cleanup efforts at the U.S. Department of Energy's (DOE's) weapons production facilities. In advance of these D ampersand D activities, it is becoming increasingly urgent that standards be established for the release of materials with residual radioactive contamination. The only standards for unrestricted release that currently exist address surface contamination. The methods used to justify those standards were developed some 20 yr ago and may not satisfy today's criteria. Furthermore, the basis of setting standards has moved away from the traditional open-quotes instrumentation-basedclose quotes concept toward a open-quotes risk-basedclose quotes approach. Therefore, as new release standards are developed, it will be necessary that risk assessment methodology consistent with modern concepts be incorporated into the process. This paper discusses recent developments in risk methodology and issues and concerns regarding the future development of standards for the release of radioactively contaminated materials

Petroleum and hazardous material releases from industrial facilities associated with Hurricane Katrina.

Science.gov (United States)

Santella, Nicholas; Steinberg, Laura J; Sengul, Hatice

2010-04-01

Hurricane Katrina struck an area dense with industry, causing numerous releases of petroleum and hazardous materials. This study integrates information from a number of sources to describe the frequency, causes, and effects of these releases in order to inform analysis of risk from future hurricanes. Over 200 onshore releases of hazardous chemicals, petroleum, or natural gas were reported. Storm surge was responsible for the majority of petroleum releases and failure of storage tanks was the most common mechanism of release. Of the smaller number of hazardous chemical releases reported, many were associated with flaring from plant startup, shutdown, or process upset. In areas impacted by storm surge, 10% of the facilities within the Risk Management Plan (RMP) and Toxic Release Inventory (TRI) databases and 28% of SIC 1311 facilities experienced accidental releases. In areas subject only to hurricane strength winds, a lower fraction (1% of RMP and TRI and 10% of SIC 1311 facilities) experienced a release while 1% of all facility types reported a release in areas that experienced tropical storm strength winds. Of industrial facilities surveyed, more experienced indirect disruptions such as displacement of workers, loss of electricity and communication systems, and difficulty acquiring supplies and contractors for operations or reconstruction (55%), than experienced releases. To reduce the risk of hazardous material releases and speed the return to normal operations under these difficult conditions, greater attention should be devoted to risk-based facility design and improved prevention and response planning.

Controlled release of phenytoin for epilepsy treatment from titania and silica based materials

International Nuclear Information System (INIS)

Lopez, Tessy; Ortiz, Emma; Meza, Doraliz; Basaldella, Elena; Bokhimi, Xim; Magana, Carlos; Sepulveda, Antonio; Rodriguez, Francisco; Ruiz, Javier

2011-01-01

Research highlights: → Template technique was used to obtain well ordered nanostructured materials: SBA-15 and titania tubes. → Phenytoin (PH), a drug used in epilepsy treatment, was loaded in these materials to used como PH release. → Loaded PH showed a good stability inside the used materials as observed by spectroscopy analysis. → The load-release PH are faster in nanostructured TiO2 tubes than in mesoporous silica matrix. → There is an inverse effect of the surface area of the structured materials on the amount of released PH. - Abstract: Template technique was used to obtain well ordered nanostructured materials: mesoporous silica and nanostructured titania tubes. This technique permits the synthesis of solids with controlled mesoporosity, where a large variety of molecules that have therapeutic activity can be hosted and further released to specific sites. In this work phenytoin (PH), a drug used in epilepsy treatment, was loaded in ordered mesoporous silica (SBA 15) and nanostructured titania tubes (TiO 2 ). The pure materials and those containing PH were characterized by X-ray diffraction, FTIR spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and N 2 adsorption-desorption at 77 K. In order to determine the loading capacity of the antiepileptic drug on these silica- and titania-based materials, the loading and release of PH was investigated using UV-vis spectroscopy. Tubular structures were found for the titania samples, for which the X-ray diffractograms showed to be formed by anatase and rutile phases. On the other hand, an amorphous phase was found in the silica sample. A highly ordered hexagonal structure of 1D cylindrical channels was also observed for this material. Loaded PH showed a good stability inside the used materials as observed by spectroscopy analysis. The adsorption and desorption of PH are faster in nanostructured TiO 2 tubes than in mesoporous silica matrix.

Modeling release of chemicals from multilayer materials into food

Directory of Open Access Journals (Sweden)

Huang Xiu-Ling

2016-01-01

Full Text Available The migration of chemicals from materials into food is predictable by various mathematical models. In this article, a general mathematical model is developed to quantify the release of chemicals through multilayer packaging films based on Fick's diffusion. The model is solved numerically to elucidate the effects of different diffusivity values of different layers, distribution of chemical between two adjacent layers and between material and food, mass transfer at the interface of material and food on the migration process.

Release process for non-real property containing residual radioactive material

International Nuclear Information System (INIS)

Ranek, N.L.; Chen, S.Y.; Kamboj, S.; Hensley, J.; Burns, D.; Fleming, R.; Warren, S.; Wallo, A.

1997-01-01

It is DOE's objective to operate its facilities and to conduct its activities so that radiation exposures to members of the public are maintained within acceptable limits and exposures to residual radioactive materials are controlled. To accomplish this, DOE has adopted Order DOE 5400.51 'Radiation Protection of the Public and the Environment', and will be promulgating IO CR Part 834 to codify and clarify the requirements of DOE 5400.5. Under both DOE 5400.5 and 10 CR Part 834, radioactively contaminated DOE property is prohibited from release unless specific actions have been completed prior to the release. This paper outlines a ten-step process that, if followed, will assist DOE Operations and contractor personnel in ensuring that the required actions established by Order DOE 5400.5 and 10 CR Part 834 have been appropriately completed prior to the release for reuse or recycle of non-real property (e.g., office furniture, computers, hand tools, machinery, vehicles and scrap metal). Following the process will assist in ensuring that radiological doses to the public from the released materials will meet applicable regulatory standards and be as low as reasonably achievable (ALARA)

User's guide for the KBERT 1.0 code: For the knowledge-based estimation of hazards of radioactive material releases from DOE nuclear facilities

International Nuclear Information System (INIS)

Browitt, D.S.; Washington, K.E.; Powers, D.A.

1995-07-01

The possibility of worker exposure to radioactive materials during accidents at nuclear facilities is a principal concern of the DOE. The KBERT software has been developed at Sandia National Laboratories under DOE support to address this issue by assisting in the estimation of risks posed by accidents at chemical and nuclear facilities. KBERT is an acronym for Knowledge-Based system for Estimating hazards of Radioactive material release Transients. The current prototype version of KBERT focuses on calculation of doses and consequences to in-facility workers due to accidental releases of radioactivity. This report gives detailed instructions on how a user who is familiar with the design, layout and potential hazards of a facility can use KBERT to assess the risks to workers in that facility. KBERT is a tool that allows a user to simulate possible accidents and observe the predicted consequences. Potential applications of KBERT include the evaluation of the efficacy of evacuation practices, worker shielding, personal protection equipment and the containment of hazardous materials

Radioactive materials released from nuclear power plants: Annual report, 1984

Energy Technology Data Exchange (ETDEWEB)

Tichler, J.; Norden, K.; Congemi, J.

1987-08-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1984 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1984 release data are summarized in tabular form. Data covering specific radionuclides are summarized.

Controlled release of phenytoin for epilepsy treatment from titania and silica based materials

Energy Technology Data Exchange (ETDEWEB)

Lopez, Tessy, E-mail: tessy3@prodigy.net.mx [Universidad Autonoma Metropolitana-Xochimilco. Departamento de Microbiologia. Calzada del Hueso 1100, Col. Villa Quietud, Coyoacan, C.P. 04960, Mexico D.F. Mexico (Mexico); Instituto Nacional de Neurologia y Neurocirugia ' MVS' . Laboratorio de Nanotecnologia. Av. Insurgentes Sur 3877, Col. La Fama, Tlalpan, 14269, Mexico, D.F. Mexico (Mexico); Department of Chemical and Biomolecular Engineering, Tulane University, New Orleans, LA 70118 (United States); Ortiz, Emma [Instituto Nacional de Neurologia y Neurocirugia ' MVS' . Laboratorio de Nanotecnologia. Av. Insurgentes Sur 3877, Col. La Fama, Tlalpan, 14269, Mexico, D.F. Mexico (Mexico); Meza, Doraliz [Universidad Autonoma Metropolitana-Iztapalapa, Departamento de Quimica, Av. San Rafael Atlixco 186, A.P. 55-534, Mexico D.F., C.P. 09340 (Mexico); Basaldella, Elena [CIC-CINDECA - Universidad Nacional de La Plata - Calle 47 No 257 - La Plata (Argentina); Bokhimi, Xim; Magana, Carlos [Instituto de fisica, UNAM. Circuito de la Investigacion s/n. C.U. Mexico D.F. 01000 (Mexico); Sepulveda, Antonio; Rodriguez, Francisco; Ruiz, Javier [Departamento de Quimica Inorganica, Universidad de Alicante. Apartado 99, E-03080 Alicante, Espana Spain (Spain)

2011-04-15

Research highlights: {yields} Template technique was used to obtain well ordered nanostructured materials: SBA-15 and titania tubes. {yields} Phenytoin (PH), a drug used in epilepsy treatment, was loaded in these materials to used como PH release. {yields} Loaded PH showed a good stability inside the used materials as observed by spectroscopy analysis. {yields} The load-release PH are faster in nanostructured TiO2 tubes than in mesoporous silica matrix. {yields} There is an inverse effect of the surface area of the structured materials on the amount of released PH. - Abstract: Template technique was used to obtain well ordered nanostructured materials: mesoporous silica and nanostructured titania tubes. This technique permits the synthesis of solids with controlled mesoporosity, where a large variety of molecules that have therapeutic activity can be hosted and further released to specific sites. In this work phenytoin (PH), a drug used in epilepsy treatment, was loaded in ordered mesoporous silica (SBA 15) and nanostructured titania tubes (TiO{sub 2}). The pure materials and those containing PH were characterized by X-ray diffraction, FTIR spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and N{sub 2} adsorption-desorption at 77 K. In order to determine the loading capacity of the antiepileptic drug on these silica- and titania-based materials, the loading and release of PH was investigated using UV-vis spectroscopy. Tubular structures were found for the titania samples, for which the X-ray diffractograms showed to be formed by anatase and rutile phases. On the other hand, an amorphous phase was found in the silica sample. A highly ordered hexagonal structure of 1D cylindrical channels was also observed for this material. Loaded PH showed a good stability inside the used materials as observed by spectroscopy analysis. The adsorption and desorption of PH are faster in nanostructured TiO{sub 2} tubes than in mesoporous silica

Biocompatibility evaluations and biomedical sensing applications of nitric oxide-releasing/generating polymeric materials

Science.gov (United States)

Wu, Yiduo

Nitric oxide (NO) is a potent signaling molecule secreted by healthy vascular endothelial cells (EC) that is capable of inhibiting the activation and adhesion of platelets, preventing inflammation and inducing vasodilation. Polymeric materials that mimic the EC through the continuous release or generation of NO are expected to exhibit enhanced biocompatibility in vivo. In this dissertation research, the biocompatibility of novel NO-releasing/generating materials has been evaluated via both in vitro and in vivo studies. A new in vitro platelet adhesion assay has been designed to quantify platelet adhesion on NO-releasing/generating polymer surfaces via their innate lactate dehydrogenase (LDH) content. Using this assay, it was discovered that continuous NO fluxes of up to 7.05 x10-10 mol cm-2 min-1 emitted from the polymer surfaces could reduce platelet adhesion by almost 80%. Such an in vitro biocompatibility assay can be employed as a preliminary screening method in the development of new NO-releasing/generating materials. In addition, the first in vivo biocompatibility evaluation of NO-generating polymers was conducted in a porcine artery model for intravascular oxygen sensing catheters. The Cu(I)-catalyzed decomposition of endogenous S-nitrosothiols (RSNOs) generated NO in situ at the polymer/blood interface and offered enhanced biocompatibility to the NO-generating catheters along with more accurate analytical results for intra-arterial measurements of PO2 levels. NO-generating polymers can also be utilized to fabricate electrochemical RSNO sensors based on the amperometric detection of NO generated by the reaction of RSNOs with immobilized catalysts. Unlike conventional methodologies employed to measure labile RSNO, the advantage of the RSNO sensor method is that measurement in whole blood samples is possible and this minimizes sample processing artifacts in RSNO measurements. An electrochemical RSNO sensor with organoselenium crosslinked polyethylenimine (RSe

Influence of plume rise on the consequences of radioactive material releases

International Nuclear Information System (INIS)

Russo, A.J.; Wayland, J.R.; Ritchie, L.T.

1977-01-01

Estimates of health consequences resulting from a postulated nuclear reactor accident can be strongly dependent on the buoyant rise of the plume of released radioactive material. The sensitivity of the consequences of a postulated accident to two different plume rise models has been investigated. The results of these investigations are the subject of this report. One of the models includes the effects of emission angle, momentum, and radioactive heating of the released material. The difference in the consequence estimates from the two models can exceed an order of magnitude under some conditions, but in general the results are similar

In vitro release of doxycycline from bioabsorbable materials and acrylic strips

DEFF Research Database (Denmark)

Larsen, T

1990-01-01

Treatment of marginal periodontitis may include use of local antibiotics. In the present in vitro study the bioabsorbable materials Surgicel, Tissell, and CollaCote and acrylic strips were examined for release of doxycycline into liquids and residual antibacterial activity of the materials. Pieces...

The effect of release liner materials on adhesive contaminants, paper recycling and recycled paper properties

Science.gov (United States)

Richard Venditti; Richard Gilbert; Andy Zhang; Said Abubakr

2000-01-01

Release liner waste material is found in post-consumer waste streams and is also a significant component of the preconsumer waste stream generated in the manufacturing of adhesive products. To date, very little has been reported pertaining to the behavior of release liner in paper recycling. In this study, the effect of the release liner material on the behavior of...

Bulk-scaffolded hydrogen storage and releasing materials and methods for preparing and using same

Science.gov (United States)

Autrey, S Thomas [West Richland, WA; Karkamkar, Abhijeet J [Richland, WA; Gutowska, Anna [Richland, WA; Li, Liyu [Richland, WA; Li, Xiaohong S [Richland, WA; Shin, Yongsoon [Richland, WA

2011-06-21

Compositions are disclosed for storing and releasing hydrogen and methods for preparing and using same. These hydrogen storage and releasing materials exhibit fast release rates at low release temperatures without unwanted side reactions, thus preserving desired levels of purity and enabling applications in combustion and fuel cell applications.

Release of axonally transported material from an in vitro amphibian sciatic nerve preparation

International Nuclear Information System (INIS)

Snyder, R.E.

1988-01-01

The rapid axonal transport of a pulse of [35S]methionine-labelled material was used to study the release of transported material from amphibian nerve maintained in vitro. Following creation of a moving pulse of activity in a dorsal root ganglion-sciatic nerve preparation, the ganglion was removed and the nerve placed in a three-compartment tray, the section of nerve in the middle compartment containing no truncated branches (unbranched section). All three compartments were filled with a saline solution that in some studies contained nonradioactive methionine (1.0 mmol/L). Analysis of studies in which nonradioactive methionine was absent revealed that labelled material appeared in the bathing solution of the end compartments that contained truncated branches, but not in the solution of the middle (unbranched) compartment. The quantity of label released in the branched compartments was approximately 6% of that remaining in the corresponding section of nerve following an 18-20 h incubation period. However, when nonradioactive methionine was present, all compartments showed an additional activity in the bathing solution of approximately 10% of that remaining in the nerve. In another study in which a position-sensitive detector of ionizing radiation was used to monitor progress of the pulse, it was found that activity did not enter the bathing solution of a compartment prior to the pulse of activity. It is concluded that in the absence of methionine from the bathing solution, axonally transported material is released only from regions of nerve that contain severed axons; however, the presence of methionine allows transported material to be released from nerve containing intact axons. Ultrafiltration studies and thin-layer chromatography revealed the majority of material released to be of low-molecular weight (less than 30,000 daltons) and not free [35S]methionine

A Selection of Nitric Oxide-Releasing Materials Incorporating S-Nitrosothiols

Science.gov (United States)

Lutzke, Alec

Nitric oxide (NO) is a diatomic radical that occurs as a crucial component of mammalian biochemistry. As a signaling molecule, NO participates in the regulation of vascular tone and maintains the natural antithrombotic function of the healthy endothelium. Furthermore, NO is produced by phagocytes as part of the immune response, and exhibits both antimicrobial and wound-healing effects. In combination, these beneficial properties have led to the use of exogenous NO as a multifunctional therapeutic agent. However, the comparatively short half-life of NO under physiological conditions often renders systemic administration infeasible. This limitation is addressed by the use of NO-releasing polymeric materials, which permit the localized delivery of NO directly at the intended site of action. Such polymers have been utilized in the development of antithrombotic or antibacterial materials for biointerfacial applications, including tissue engineering and the fabrication of medical devices. NO release from polymers has most frequently been achieved through the incorporation of functional groups that are susceptible to NO-forming chemical decomposition in response to appropriate environmental stimuli. While numerous synthetic sources of NO are known, the S-nitrosothiol (RSNO) functional group occurs naturally in the form of S-nitrosocysteine residues in both proteins and small molecule species such as S-nitrosoglutathione. RSNOs are synthesized directly from thiol precursors, and their NO-forming decay has generally been established to produce the corresponding disulfide as a relatively benign organic byproduct. For these reasons, RSNOs have been conscripted as practical NO donors within a physiological environment. This dissertation describes the synthesis and characterization of RSNO-based NO-releasing polymers derived from the polysaccharides chitin and chitosan, as well as the development of amino acid ester-based NO-releasing biodegradable poly

Ice-Release and Erosion Resistant Materials for Wind Turbines

Science.gov (United States)

Zhang, Wei; Brinn, Cameron; Cook, Alex; Pascual-Marquez, Fernando

2017-11-01

Icing conditions may cause wind turbine generators to partially lose productivity or to be completely shut down to avoid structural damage. At present, commercially available technologies to mitigate this problem consist of expensive, energy hungry heating elements, which costs roughly 70,000 euro per medium size turbine. Conventional passive ice protection coating systems heavily rely on delicate surface structures and expensive materials to create water repellent superhydrophobic / low surface energy surfaces, which have been proven to be ineffective against ice accumulation. The lack of performance among conventional ice protection materials stems from a flaw in the approach to the problem: failure to recognize that water in its liquid form (WATER) and water in its solid form (ICE) are two different things. Something that works for WATER does not automatically work for ICE. Another reason is that many superhydrophobic materials are often reliant upon often fragile micro-structured surfaces to achieve their intended effects. This paper discusses a fundamentally different approach to the creation of a robust, low cost, durable, and multifunctional materials for ice release and erosion resistance. This National Science Foundation sponsored ice-release coating technology holds promise for protecting wind turbine blades and towers, thus potentially increasing reliability for power generation under icing conditions. Because of the vulnerability of wind turbine blades to ice buildup and erosion damages, wind farm facilities stand to reap considerable benefits.

Monitoring for radioactive materials releasing to environment in M310 reformatived nuclear power plant

International Nuclear Information System (INIS)

Yin Zhenyu; Yang Guangli; Xu Guang

2012-01-01

Airborne radioactive materials of nuclear power plant (NPP) releases to the environment from the stack of NPP. Radioactive liquid waste releases of the ocean, the fluvial and the lake through the liquid waste letdyke of NPP. Further more, a few radioactive waste may be taken out of the NPP by vehicle or personnel. For the purpose of strict management and control above-mentioned waste, we use detect equipment monitoring radioactive waste of NPP. Management and control for the releasing of radioactive material to the environment in M310 reformatived NPP is strict and safety. (authors)

In-pile test of tritium release from tritium breeding materials (VOM-21H experiment)

International Nuclear Information System (INIS)

Kurasawa, Toshimasa; Takeshita, Hidefumi; Watanabe, Hitoshi; Yoshida, Hiroshi.

1986-10-01

Material development and blanket design of lithium-based ceramics such as lithium oxide, lithium aluminate, lithium silicate and lithium zirconate have been performed in Japan, United State of America and Europian Communities. Lithium oxide is a most attractive candidate for tritium breeding materials because of its high lithium density, high thermal conductivity and good tritium release performance. This work has been done to clarify the characteristics of tritium release and recovery from Li 2 O by means of in-situ tritium release measurement. The effects of temperature and sweep gas composition on the tritium release were investigated in this VOM-21H Experiment. Good measurement of tritium release was achieved but there were uncertainties in reproduciblity of data. The experimental results show that the role of surface adsorption/desorption makes a significant contribution to the tritium release and tritium inventory. Also, it is necessary to define the rate limiting process either diffusion or surface adsorption/desorption. (author)

The Risoe model for calculating the consequences of the release of radioactive material to the atmosphere

International Nuclear Information System (INIS)

Thykier-Nielsen, S.

1980-07-01

A brief description is given of the model used at Risoe for calculating the consequences of releases of radioactive material to the atmosphere. The model is based on the Gaussian plume model, and it provides possibilities for calculation of: doses to individuals, collective doses, contamination of the ground, probability distribution of doses, and the consequences of doses for give dose-risk relationships. The model is implemented as a computer program PLUCON2, written in ALGOL for the Burroughs B6700 computer at Risoe. A short description of PLUCON2 is given. (author)

New plant releases from the USDA-NRCS Aberdeen, Idaho, Plant Materials Center

Science.gov (United States)

L. St. John; P. Blaker

2001-01-01

The Plant Materials Center at Aberdeen, Idaho, is operated by the United States Department of Agriculture, Natural Resources Conservation Service. The purpose of the Plant Materials Center is to evaluate and release plant materials for conservation use and to develop and transfer new technology for the establishment and management of plants. The Center serves portions...

[Fabrication of a new composite scaffold material for delivering rifampicin and its sustained drug release in rats].

Science.gov (United States)

Ma, Xue-Ming; Lin, Zhen; Zhang, Jia-Wei; Sang, Chao-Hui; Qu, Dong-Bin; Jiang, Jian-Ming

2016-03-01

To fabricate a new composite scaffold material as an implant for sustained delivery of rifampicin and evaluate its performance of sustained drug release and biocompatibility. The composite scaffold material was prepared by loading poly(lactic-co-glycolic) acid (PLGA) microspheres that encapsulated rifampicin in a biphasic calcium composite material with a negative surface charge. The in vitro drug release characteristics of the microspheres and the composite scaffold material were evaluated; the in vivo drug release profile of the composite scaffold material implanted in a rat muscle pouch was evaluated using high-performance liquid chromatography. The biochemical parameters of the serum and liver histopathologies of the rats receiving the transplantation were observed to assess the biocompatibility of the composite scaffold material. The encapsulation efficiency and drug loading efficiency of microspheres were (56.05±5.33)% and (29.80±2.88)%, respectively. The cumulative drug release rate of the microspheres in vitro was (94.19±5.4)% at 28 days, as compared with the rate of (82.23±6.28)% of composite scaffold material. The drug-loaded composite scaffold material showed a good performance of in vivo drug release in rats, and the local drug concentration still reached 16.18±0.35 µg/g at 28 days after implantation. Implantation of the composite scaffold material resulted in transient and reversible liver injury, which was fully reparred at 28 days after the implantation. The composite scaffold material possesses a good sustained drug release capacity and a good biocompatibility, and can serve as an alternative approach to conventional antituberculous chemotherapy.

A method for prevention of radioactive material release

International Nuclear Information System (INIS)

Uchida, Shunsuke; Sato, Chikara; Kitamura, Masao.

1975-01-01

Object: To provide a method for preventing an underwater radioactive material from being released in a simple and highly reliable manner, which can decrease an amount of radioactive materials discharged into open air from reactor water containing a large amount of radioactive materials such as a reactor core pool. Structure: Pure warm water higher in temperature than that of reactor water is poured from the top of a water surface of a water tank which stores reactor water containing radioactive materials such as radioactive iodine, and water is drawn through an outlet located downwardly of the pure warm water inlet to form a layer of pure warm water at the upper part of the water tank while preventing diffusion of the reactor water into the pure warm water by the difference in density between the reactor water and the pure warm water and downward movement of the pure warm water, thereby preventing contact of the reactor water with the atmosphere and diffusion of the radioactive material into the atmosphere. (Kamimura, M.)

Methods for determining the release of radioactive material into the environment

International Nuclear Information System (INIS)

Farges, L.; Daw, H.T.

1976-01-01

The current policy on the discharge of radioactive effluents calls for the containment of radioactive wastes in most instances. The resulting doses to individuals and populations have been shown by many surveys to be very small (UNSCEAR Report, 1972). Nevertheless, small amounts of radioactive releases are made to the environment during normal operation of nuclear facilities. Whenever discharge of radioactive effluents to the environment is permitted, careful consideration is made of all the relevant factors which might lead to exposure of man. However, with the expansion of nuclear power programmes, more sophistication is required in setting discharge limits to the environment, taking into consideration future sources as well as present sources. The IAEA's recommendations conform to the dose limitation system set out by the International Commission on Radiological Protection (ICRP). The system implies that the individual dose limits should never be exceeded. Furthermore, the ICRP guidelines require that doses be kept as low as reasonably possible, taking social and economic considerations into account. This second objective, usually called optimization, implies the use of differential cost-benefit analysis. At present, decisions are still made by other procedures, for example, by applying safety factors to release limits derived only from the dose limits. However, the ICRP system of dose limitation, including optimization, appears to be a more rational approach to the establishment of release limits. Thus, it is necessary to provide basic material on concepts which are intended for use and decision making by national authorities, and the Agency plans to publish a series of complementary documents on the application of these concepts to various specific cases. (author)

Comparison of the release of constituents from granular materials under batch and column testing.

Science.gov (United States)

Lopez Meza, Sarynna; Garrabrants, Andrew C; van der Sloot, Hans; Kosson, David S

2008-01-01

Column leaching testing can be considered a better basis for assessing field impact data than any other available batch test method and thus provides a fundamental basis from which to estimate constituent release under a variety of field conditions. However, column testing is time-intensive compared to the more simplified batch testing, and may not always be a viable option when making decisions for material reuse. Batch tests are used most frequently as a simple tool for compliance or quality control reasons. Therefore, it is important to compare the release that occurs under batch and column testing, and establish conservative interpretation protocols for extrapolation from batch data when column data are not available. Five different materials (concrete, construction debris, aluminum recycling residue, coal fly ash and bottom ash) were evaluated via batch and column testing, including different column flow regimes (continuously saturated and intermittent unsaturated flow). Constituent release data from batch and column tests were compared. Results showed no significant difference between the column flow regimes when constituent release data from batch and column tests were compared. In most cases batch and column testing agreed when presented in the form of cumulative release. For arsenic in carbonated materials, however, batch testing underestimates the column constituent release for most LS ratios and also on a cumulative basis. For cases when As is a constituent of concern, column testing may be required.

Resolving Radiological Classification and Release Issues for Many DOE Solid Wastes and Salvageable Materials

International Nuclear Information System (INIS)

Hochel, R.C.

1999-01-01

The cost effective radiological classification and disposal of solid materials with potential volume contamination, in accordance with applicable U.S. Department of Energy (DOE) Orders, suffers from an inability to unambiguously distinguish among transuranic waste, low-level waste, and unconditional-release materials in a generic way allowing in-situ measurement and verification. Depending on a material''s classification, disposal costs can vary by a hundred-fold. With these large costs at risk, the issues involved in making defensible decisions are ripe for closer scrutiny. In many cases, key issues can be easily resolved by a combination of process information, some simple measurements, and calculational predictions from a computer model for radiation shielding. The proper classification and disposal of many solid wastes requires a measurement regime that is able to show compliance with a variety of institutional and regulatory contamination limits. Ultimate responsibility for this, of course, rests with radiological control or health physics organization of the individual site, but there are many measurements which can be performed by operations and generation organizations to simplify the process and virtually guarantee acceptance. Although this is not possible for all potential solid wastes, there are many that do lend themselves to such measures, particularly some of large volumes and realizable cost savings. Mostly what is needed for this to happen are a few guiding rules, measurement procedures, and cross checks for potential pitfalls. Several examples are presented here and discussed that demonstrate the possibilities, including one which was successfully applied to bulk contamination

14 CFR 1213.107 - Preventing unauthorized release of sensitive but unclassified (SBU) information/material to the...

Science.gov (United States)

2010-01-01

.../material to the news media. (a) All NASA SBU information requires accountability and approval for release... sensitive but unclassified (SBU) information/material to the news media. 1213.107 Section 1213.107 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION RELEASE OF INFORMATION TO NEWS AND...

Assessment of nanoparticle release and associated health effect of polymer-silicon composites

International Nuclear Information System (INIS)

Zhu, H; Irfan, A; Sachse, S; Njuguna, J

2012-01-01

Little information is currently available on possible release of nanomaterials or/and nanoparticles (NP) from conventional and novel products and associated health effect. This study aimed to assess the possible release of NP during the application stage of conventional and nanoproducts. NP release was monitored during physical processing of polymer-silicon composites, and the toxicity of both the released NP and the raw silica nanomaterials that were used as fillers in the nanocomposites was assessed in vitro using human lung epithelial A549 cells. This study suggests that 1) NP can be released from the conventional and novel polymer-silicon composites under certain application scenario; 2) the level of NP release from polymer composites could be altered by different reinforcement materials; e.g. nanostructured MMT could reduce the release while SiO2 NP could increase the release; 3) working with polymer composites under certain conditions could risk inhalation of high level of polymer NP; 4) raw nanomaterials appeared to be toxic in the chosen in vitro system. Further study of the effect of novel filler materials on NP release from final polymer products and the effect of released NP on environment and human health will inform design of safe materials and minimization of negative impact on the environment and human health.

Release from control of inactive material from decommissioning the ASTRA research reactor

International Nuclear Information System (INIS)

Brandl, A.; Hrnecek, E.; Steger, F.; Kurz, H.; Meyer, F.; Karacson, P.

2003-01-01

The Austrian Research Centers Seibersdorf have been operating a 10 MW ASTRA research reactor from 1960 until 1999. After that date, a submission of the intention to decommission the reactor has been provided to the Competent Authorities. After completion of an Environmental Impact Study by the Competent Authorities and modification of the Permissions for Site Use, the reactor finally entered the decommissioning phase in 2003. Inactive materials from the decommissioning site are expected to be released from control. The procedure for such a release from control agreed upon between the Competent Authorities and ARC Seibersdorf involves a four-step measurement, verification, and certification process detailed in this paper. By September 2003, this four-step procedure has been completed for 16500 kg of steel re-enforced concrete and for 5500 kg of other materials; the release from control of 3000 kg of paraffin and 10000 kg of graphite from the thermal column are planned for the near future. (author)

Developments in consequence modelling of accidental releases of hazardous materials

NARCIS (Netherlands)

Boot, H.

2012-01-01

The modelling of consequences of releases of hazardous materials in the Netherlands has mainly been based on the “Yellow Book”. Although there is no updated version of this official publication, new insights have been developed during the last decades. This article will give an overview of new

Possible chaoticity for the time series of the amount of nuclear information released by the newsmedia

International Nuclear Information System (INIS)

Ohnishi, T.

1995-01-01

The amount of information concerning nuclear problems was time analysed which has been released by three types of the newsmedia in Japan, the press, television and magazines during the past 20 years. The time series of the logarithmic value of the amount released by some of the newsmedia was found to be possibly chaotic, or at least to be non-stochastic. Such a characteristic of time series can be interpreted as a result of the exertion of a certain sort of selection process in the interior of the newsmedia in deciding an event as news to be released. (author)

Chitosan/alginate based multilayers to control drug release fromophthalmic lens

OpenAIRE

Silva, Diana; Pinto, Luís F. V.; Bozukova, Dimitriya; Santos, Luís F.; Serro, Ana Paula; Saramago, Benilde

2016-01-01

In this study we investigated the possibility of using layer-by-layer deposition, based in natural polymers (chitosan and alginate), to control the release of different ophthalmic drugs from three types of lens materials: a silicone-based hydrogel recently proposed by our group as drug releasing soft contact lens (SCL) material and two commercially available materials: CI26Y for intraocular lens (IOLs) and Definitive 50 for SCLs. The optimised coating, consisting in one double layer of (algin...

Radioactive materials released from nuclear power plants. Annual report, 1982. Volume 3

International Nuclear Information System (INIS)

Tichler, J.; Norden, K.

1986-02-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1982 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1982 release data are summarized in tabular form. Data covering specific radionuclides are summarized

Materials for Pharmaceutical Dosage Forms: Molecular Pharmaceutics and Controlled Release Drug Delivery Aspects

Directory of Open Access Journals (Sweden)

Patrick P. DeLuca

2010-09-01

Full Text Available Controlled release delivery is available for many routes of administration and offers many advantages (as microparticles and nanoparticles over immediate release delivery. These advantages include reduced dosing frequency, better therapeutic control, fewer side effects, and, consequently, these dosage forms are well accepted by patients. Advances in polymer material science, particle engineering design, manufacture, and nanotechnology have led the way to the introduction of several marketed controlled release products and several more are in pre-clinical and clinical development.

Regulatory analysis on criteria for the release of patients administered radioactive material

International Nuclear Information System (INIS)

Schneider, S.; McGuire, S.A.

1994-05-01

The Nuclear Regulatory Commission (NRC) has received two petitions to amend its regulations in 10 CFR Parts 20 and 35 as they apply to doses received by members of the public exposed to patients released from a hospital after they have been administered radioactive material. While the two petitions are not identical they both request that the NRC establish a dose limit of 5 millisieverts (0.5 rem) per year for individuals exposed to patients who have been administered radioactive materials. This Regulatory Analysis evaluates three alternatives. Alternative 1 is for the NRC to amend its patient release criteria in 10 CFR 35.75 to use the more stringent dose limit of 1 millisievert per year in 10 CFR 20.1301(a) for its patient release criteria. Alternative 2 is for the NRC to continue using the existing patient release criteria in 10 CFR 35.75 of 1,110 megabecquerels of activity or a dose rate at one meter from the patient of 0.05 millisievert per hour. Alternative 3 is for the NRC to amend the patient release criteria in 10 CFR 35.75 to specify a dose limit of 5 millisieverts for patient release. The evaluation indicates that Alternative 1 would cause a prohibitively large increase in the national health care cost from retaining patients in a hospital longer and would cause significant personal and psychological costs to patients and their families. The choice of Alternatives 2 or 3 would affect only thyroid cancer patients treated with iodine-131. For those patients, Alternative 3 would result in less hospitalization than Alternative 2. Alternative 3 has a potential decrease in national health care cost of $30,000,000 per year but would increase the potential collective dose from released therapy patients by about 2,700 person-rem per year, mainly to family members

Regulatory analysis on criteria for the release of patients administered radioactive material

Energy Technology Data Exchange (ETDEWEB)

Schneider, S.; McGuire, S.A. [Nuclear Regulatory Commission, Washington, DC (United States). Div. of Regulatory Applications; Behling, U.H.; Behling, K.; Goldin, D. [Cohen (S.) and Associates, Inc., McLean, VA (United States)

1994-05-01

The Nuclear Regulatory Commission (NRC) has received two petitions to amend its regulations in 10 CFR Parts 20 and 35 as they apply to doses received by members of the public exposed to patients released from a hospital after they have been administered radioactive material. While the two petitions are not identical they both request that the NRC establish a dose limit of 5 millisieverts (0.5 rem) per year for individuals exposed to patients who have been administered radioactive materials. This Regulatory Analysis evaluates three alternatives. Alternative 1 is for the NRC to amend its patient release criteria in 10 CFR 35.75 to use the more stringent dose limit of 1 millisievert per year in 10 CFR 20.1301(a) for its patient release criteria. Alternative 2 is for the NRC to continue using the existing patient release criteria in 10 CFR 35.75 of 1,110 megabecquerels of activity or a dose rate at one meter from the patient of 0.05 millisievert per hour. Alternative 3 is for the NRC to amend the patient release criteria in 10 CFR 35.75 to specify a dose limit of 5 millisieverts for patient release. The evaluation indicates that Alternative 1 would cause a prohibitively large increase in the national health care cost from retaining patients in a hospital longer and would cause significant personal and psychological costs to patients and their families. The choice of Alternatives 2 or 3 would affect only thyroid cancer patients treated with iodine-131. For those patients, Alternative 3 would result in less hospitalization than Alternative 2. Alternative 3 has a potential decrease in national health care cost of $30,000,000 per year but would increase the potential collective dose from released therapy patients by about 2,700 person-rem per year, mainly to family members.

Temperature-regulated guest admission and release in microporous materials

Science.gov (United States)

Li, Gang (Kevin); Shang, Jin; Gu, Qinfen; Awati, Rohan V.; Jensen, Nathan; Grant, Andrew; Zhang, Xueying; Sholl, David S.; Liu, Jefferson Z.; Webley, Paul A.; May, Eric F.

2017-06-01

While it has long been known that some highly adsorbing microporous materials suddenly become inaccessible to guest molecules below certain temperatures, previous attempts to explain this phenomenon have failed. Here we show that this anomalous sorption behaviour is a temperature-regulated guest admission process, where the pore-keeping group's thermal fluctuations are influenced by interactions with guest molecules. A physical model is presented to explain the atomic-level chemistry and structure of these thermally regulated micropores, which is crucial to systematic engineering of new functional materials such as tunable molecular sieves, gated membranes and controlled-release nanocontainers. The model was validated experimentally with H2, N2, Ar and CH4 on three classes of microporous materials: trapdoor zeolites, supramolecular host calixarenes and metal-organic frameworks. We demonstrate how temperature can be exploited to achieve appreciable hydrogen and methane storage in such materials without sustained pressure. These findings also open new avenues for gas sensing and isotope separation.

The Insoluble Carbonaceous Material of CM Chondrites as Possible Source of Discrete Organics During the Asteroidal Aqueous Phase

Science.gov (United States)

Yabuta, H.; Williams, L.; Cody, G.; Pizzarello, S.

2005-01-01

The larger portion of the organic carbon in carbonaceous chondrites (CC) is present as a complex and heterogeneous macromolecular material that is insoluble in acids and most solvents (IOM). So far, it has been analyzed only as a whole by microscopy (TEM) and spectroscopy (IR, NMR, EPR), which have offered and overview of its chemical nature, bonding, and functional group composition. Chemical or pyrolytic decomposition has also been used in combination with GC-MS to identify individual compounds released by these processes. Their value in the recognition of the original IOM structure resides in the ability to properly interpret the decomposition pathways for any given process. We report here a preliminary study of IOM from the Murray meteorite that combines both the analytical approaches described above, under conditions that would realistically model the IOM hydrothermal exposure in the meteorite parent body. The aim is to document the possible release of water and solvent soluble organics, determine possible changes in NMR spectral features, and ascertain, by extension, the effect of this loss on the frame of the IOM residue. Additional information is included in the original extended abstract.

Resolving Radiological Classification and Release Issues for Many DOE Solid Wastes and Salvageable Materials

Energy Technology Data Exchange (ETDEWEB)

Hochel, R.C.

1999-11-19

The cost effective radiological classification and disposal of solid materials with potential volume contamination, in accordance with applicable U.S. Department of Energy (DOE) Orders, suffers from an inability to unambiguously distinguish among transuranic waste, low-level waste, and unconditional-release materials in a generic way allowing in-situ measurement and verification. Depending on a material''s classification, disposal costs can vary by a hundred-fold. With these large costs at risk, the issues involved in making defensible decisions are ripe for closer scrutiny. In many cases, key issues can be easily resolved by a combination of process information, some simple measurements, and calculational predictions from a computer model for radiation shielding. The proper classification and disposal of many solid wastes requires a measurement regime that is able to show compliance with a variety of institutional and regulatory contamination limits. Ultimate responsibility for this, of course, rests with radiological control or health physics organization of the individual site, but there are many measurements which can be performed by operations and generation organizations to simplify the process and virtually guarantee acceptance. Although this is not possible for all potential solid wastes, there are many that do lend themselves to such measures, particularly some of large volumes and realizable cost savings. Mostly what is needed for this to happen are a few guiding rules, measurement procedures, and cross checks for potential pitfalls. Several examples are presented here and discussed that demonstrate the possibilities, including one which was successfully applied to bulk contamination.

Controlled release of non-steroidal antiinflammatory and anticancer drugs from hybrid materials

International Nuclear Information System (INIS)

Caravieri, Beatriz Bernardes; Molina, Eduardo Ferreira

2016-01-01

Full text: Chronic inflammation is a well known risk factor for the development of human cancer, and at least one third of all human cancers have been associated with inflammation. This can lead to cellular proliferation, a process which per se increases the risk of abnormal cell formation and ultimately the development of cancer. For treating clinical conditions such as inflammation and cancer, the most common methods (e.g., oral administration, injection) can cause unwanted side effects due to drug delivery to non-target sites and the introduction of high doses of the drug to reach the desired location. An alternative to these problems is the preparation of materials that can release drugs with different activities. Thinking about it, the aim of this study was to use a class of hybrid materials based on siloxane-polyether known as ureasil for controlled release of non-steroidal anti-inflammatory drugs (NSAIDs) such as ibuprofen (IBU) and naproxen (NAP), and anticancer, such as 5-fluorouracil (5- FU). These drugs have been incorporated in the matrix in different proportions and thereafter, were characterized by different techniques such as XRD, FTIR, DSC and SAXS. In addition, it has been evaluated the release kinetics of these species with different chemical structures. The results have shown that the drug molecules were homogeneously distributed in the xerogel hybrids, which contributed to the drug’s release profile fine-tuning. The chemical environment of the polyether chains was amended by incorporating the drugs. The analysis from XRD, FTIR, SAXS and DSC confirm the good solubility of the substances within hybrid matrix. This hybrid material based on polymers and inorganic compounds may have potential applications in human health. (author)

Controlled release of non-steroidal antiinflammatory and anticancer drugs from hybrid materials

Energy Technology Data Exchange (ETDEWEB)

Caravieri, Beatriz Bernardes; Molina, Eduardo Ferreira, E-mail: bia_ms_@hotmail.com [Universidade de Franca, SP (Brazil)

2016-07-01

Full text: Chronic inflammation is a well known risk factor for the development of human cancer, and at least one third of all human cancers have been associated with inflammation. This can lead to cellular proliferation, a process which per se increases the risk of abnormal cell formation and ultimately the development of cancer. For treating clinical conditions such as inflammation and cancer, the most common methods (e.g., oral administration, injection) can cause unwanted side effects due to drug delivery to non-target sites and the introduction of high doses of the drug to reach the desired location. An alternative to these problems is the preparation of materials that can release drugs with different activities. Thinking about it, the aim of this study was to use a class of hybrid materials based on siloxane-polyether known as ureasil for controlled release of non-steroidal anti-inflammatory drugs (NSAIDs) such as ibuprofen (IBU) and naproxen (NAP), and anticancer, such as 5-fluorouracil (5- FU). These drugs have been incorporated in the matrix in different proportions and thereafter, were characterized by different techniques such as XRD, FTIR, DSC and SAXS. In addition, it has been evaluated the release kinetics of these species with different chemical structures. The results have shown that the drug molecules were homogeneously distributed in the xerogel hybrids, which contributed to the drug’s release profile fine-tuning. The chemical environment of the polyether chains was amended by incorporating the drugs. The analysis from XRD, FTIR, SAXS and DSC confirm the good solubility of the substances within hybrid matrix. This hybrid material based on polymers and inorganic compounds may have potential applications in human health. (author)

Scenarios and methods that induce protruding or released CNTs after degradation of nanocomposite materials.

Science.gov (United States)

Hirth, Sabine; Cena, Lorenzo; Cox, Gerhard; Tomović, Zeljko; Peters, Thomas; Wohlleben, Wendel

2013-04-01

Nanocomposite materials may be considered as a low-risk application of nanotechnology, if the nanofillers remain embedded throughout the life-cycle of the products in which they are embedded. We hypothesize that release of free CNTs occurs by a combination of mechanical stress and chemical degradation of the polymer matrix. We experimentally address limiting cases: Mechanically released fragments may show tubular protrusions on their surface. Here we identify these protrusions unambiguously as naked CNTs by chemically resolved microscopy and a suitable preparation protocol. By size-selective quantification of fragments we establish as a lower limit that at least 95 % of the CNTs remain embedded. Contrary to classical fiber composite approaches, we link this phenomenon to matrix materials with only a few percent elongation at break, predicting which materials should still cover their CNT nanofillers after machining. Protruding networks of CNTs remain after photochemical degradation of the matrix, and we show that it takes the worst case combinations of weathering plus high-shear wear to release free CNTs in the order of mg/m 2 /year. Synergy of chemical degradation and mechanical energy input is identified as the priority scenario of CNT release, but its lab simulation by combined methods is still far from real-world validation.

Minutes of the workshop on off-site release criteria for contaminated materials

International Nuclear Information System (INIS)

Singh, S.P.N.

1989-11-01

A one and one-half-day workshop was held May 2-3, 1989, at the Pollard Auditorium in Oak Ridge, Tennessee, with the objective of formulating a strategy for developing reasonable and uniform criteria for releasing radioactively contaminated materials from the US Department of Energy (DOE) sites. This report contains the minutes of the workshop. At the conclusion of the workshop, a plan was formulated to facilitate the development of the above-mentioned off-site release criteria

Calculation of releases of radioactive materials in gaseous effluents from nuclear-powered merchant ships (NMS-GEFF code)

International Nuclear Information System (INIS)

Cardile, F.P.; Bangart, R.L.; Collins, J.T.

1978-06-01

The Intergovernmental Maritime Consultative Organization IMCO) is currently preparing guidelines concerning the safety of nuclear-powered merchant ships. An important aspect of these guidelines is the determination of the releases of radioactive material in effluents from these ships and the control exercised by the ships over these releases. To provide a method for the determination of these releases, the NRC staff has developed a computerized model, the NMS-GEFF Code, which is described in the following chapters. The NMS-GEFF Code calculates releases of radioactive material in gaseous effluents for nuclear-powered merchant ships using pressurized water reactors

The insoluble carbonaceous material of CM chondrites: A possible source of discrete organic compounds under hydrothermal conditions

Science.gov (United States)

Yabuta, Hikaru; Williams, Lynda B.; Cody, George D.; Alexander, Conel M. O. D.; Pizzarello, Sandra

2007-08-01

We report on the molecular analyses of the water- and solvent-soluble organic compounds released from the insoluble organic material (IOM) of the Murray meteorite upon treatment with weight-equivalent amounts of water and under conditions of elevated temperature and pressure. A varied suite of compounds was identified by gas chromatography-mass spectrometry (GC-MS). C3-C17 alkyl dicarboxylic acids and N- and O-containing hydroaromatic and aromatic compounds were found in the water extracts. The solvent extracts contained N-, O-, and S-containing aromatic compounds, a large number of their isomers and homologs, and a series of polycyclic aromatic hydrocarbons (PAHs) of up to five rings, together with noncondensed aromatic species such as substituted benzenes, biphenyl, and terphenyls as well as their substituted homologs, and hydrated PAHs. Isotopic analyses showed that residue IOMs after hydrothermal treatment had lower deuterium and 15N content than the untreated material (ΔD = -833‰ and Δ15N = -24.1) but did not differ from it in 13C composition. The effect of the hydrothermolytic release was recorded in significant differences between the NMR spectra of untreated and residue IOM. A possible relation to common precursors for the dicarboxylic acids found in the IOM and bulk extracts is discussed.

The release of organic material from clay based buffer materials and its potential implications for radionuclide transport

International Nuclear Information System (INIS)

Vilks, P.; Stroes-Gascoyne, S.; Goulard, M.; Haveman, S.A.; Bachinski, D.B.

1998-01-01

In the Canadian nuclear fuel waste disposal concept used fuel would be placed in corrosion resistant containers which would be surrounded by clay-based buffer and backfill materials in an engineered vault excavated at 500 to 1000 m depth in crystalline rock formations in the Canadian shield. Organic substances could affect radionuclide mobility due to the effects of redox and complexation reactions that increase solubility and alter mobility. The purpose of this study was to determine whether the buffer and backfill materials, proposed for use in a disposal vault, contain organics that could be leached by groundwater in large enough quantities to affect radionuclide mobility within the disposal vault and surrounding geosphere complex. Buffer material, made from a mixture of 50 wt.% Avonlea sodium bentonite and 50 wt.% silica sand, was extracted with deionized water to determine the release of dissolved organic carbon (DOC), humic acid and fulvic acid. The effect of radiation and heat from the used fuel was simulated by treating samples of buffer before leaching to various amounts of heat (60 and 90 C) for periods of 2, 4 and 6 weeks, and to ionizing radiation with doses of 25 kGy and 50 kGy. The results showed that groundwater would leach significant amounts of organics from buffer that complex with radionuclides such as the actinides, potentially affecting their solubility and transport within the disposal vault and possibly the surrounding geosphere. In addition, the leached organics would likely stimulate microbial growth by several orders of magnitude. Heating and radiation affect the amount and nature of leachable organics. (orig.)

New Class of Hybrid Materials for Detection, Capture, and "On-Demand" Release of Carbon Monoxide.

Science.gov (United States)

Pitto-Barry, Anaïs; Lupan, Alexandru; Ellingford, Christopher; Attia, Amr A A; Barry, Nicolas P E

2018-04-25

Carbon monoxide (CO) is both a substance hazardous to health and a side product of a number of industrial processes, such as methanol steam reforming and large-scale oxidation reactions. The separation of CO from nitrogen (N 2 ) in industrial processes is considered to be difficult because of the similarities of their electronic structures, sizes, and physicochemical properties (e.g., boiling points). Carbon monoxide is also a major poison in fuel cells because of its adsorption onto the active sites of the catalysts. It is therefore of the utmost economic importance to discover new materials that enable effective CO capture and release under mild conditions. However, methods to specifically absorb and easily release CO in the presence of contaminants, such as water, nitrogen, carbon dioxide, and oxygen, at ambient temperature are not available. Here, we report the simple and versatile fabrication of a new class of hybrid materials that allows capture and release of carbon monoxide under mild conditions. We found that carborane-containing metal complexes encapsulated in networks made of poly(dimethylsiloxane) react with CO, even when immersed in water, leading to dramatic color and infrared signature changes. Furthermore, we found that the CO can be easily released from the materials by simply dipping the networks into an organic solvent for less than 1 min, at ambient temperature and pressure, which not only offers a straightforward recycling method, but also a new method for the "on-demand" release of carbon monoxide. We illustrated the utilization of the on-demand release of CO from the networks by carrying out a carbonylation reaction on an electron-deficient metal complex that led to the formation of the CO-adduct, with concomitant recycling of the gel. We anticipate that our sponge-like materials and scalable methodology will open up new avenues for the storage, transport, and controlled release of CO, the silent killer and a major industrial poison.

Aerosol material release rates from zircaloy-4 at temperatures from 2000 to 22000C

International Nuclear Information System (INIS)

Mulpuru, S.R.; Wren, D.J.; Rondeau, R.K.

1987-01-01

During some postulated severe accidents involving loss of coolant and loss of emergency coolant injection, the temperatures in a CANDU reactor fuel channel become high enough to cause failure and melting of the Zircaloy fuel cladding. At such high temperatures, vapors of fission products and structural (fuel and cladding) materials will be released into the coolant steam and hydrogen mixture. These vapors will condense as cooler conditions are encountered downstream. The vapors from structural materials are relatively involatile; therefore, they will condense readily into aerosol particles. These particles, in turn, will provide sites for the condensation of the more volatile fission products. The aerosol transport of fission products in the primary heat transport system (PHTS) will thus be influenced by the structural material release rates. As part of an ongoing program to develop predictive tools for aerosol and associated fission product transport through the PHTS, experiments have been conducted to measure the vapor mass release rates of the alloying elements from Zircaloy-4 at high temperatures. The paper presents the results and analysis of these experiments

Safeguarding of emergency core cooling in case of loss-of-coolant accidents with insulation material release

International Nuclear Information System (INIS)

Pointner, W.; Broecker, A.

2012-01-01

The report on safeguarding of emergency core cooling in case of loss-of-coolant accidents with insulation material release covers the following issues: assessment of the relevant status for PWR, evaluation of the national and international (USA, Canada, France) status, actualization of recommendations, transferability from PWR to BWR. Generic studies on the core cooling capability in case of insulation material release in BWR-type reactors were evaluated.

In vivo release of calcitonin gene-related peptide-like material from the cervicotrigeminal area in the rat. Effects of electrical and noxious stimulations of the muzzle.

Science.gov (United States)

Pohl, M; Collin, E; Bourgoin, S; Clot, A M; Hamon, M; Cesselin, F; Le Bars, D

1992-10-01

The continuous perfusion with an artificial cerebrospinal fluid of the cervicotrigeminal area of the spinal cord in halothane-anaesthetized rats allowed the collection of calcitonin gene-related peptide-like material with the same immunological and chromatographic characteristics as authentic rat alpha-calcitonin gene-related peptide. The spinal release of calcitonin gene-related peptide-like material could be significantly increased by the local application of 60 mM K+ (approximately +100%), high-intensity percutaneous electrical stimulation (approximately +200%) and noxious heat (by immersion in water at 52 degrees C; approximately +150%) applied to the muzzle. By contrast, noxious mechanical (pinches) and chemical (subcutaneous formalin injection) stimulations and deep cooling (by immersion in water at 0 degrees C) of the muzzle did not alter the spinal release of calcitonin gene-related peptide-like material. In addition, low-intensity electrical stimulation, recruiting only the A alpha/beta primary afferent fibres, significantly reduced (approximately -30%) the release of calcitonin gene-related peptide-like material from the cervicotrigeminal area. These data suggest that among the various types of natural noxious stimuli, noxious heat may selectively excite calcitonin gene-related peptide-containing A delta and C primary afferent fibres projecting within the dorsal horn of the spinal cord, and that activation of A alpha/beta fibres reduces spontaneous calcitonin gene-related peptide-like material release possibly through an inhibitory presynaptic control of calcitonin gene-related peptide-containing A delta/C fibres.

TEGDMA and UDMA monomers released from composite dental material polymerized with diode and halogen lamps.

Science.gov (United States)

Wacławczyk, Agnieszka; Postek-Stefańska, Lidia; Pietraszewska, Daria; Birkner, Ewa; Zalejska-Fiolka, Jolanta; Wysoczańska-Jankowicz, Iwona

2018-03-20

More than 35 substances released from composite fillings have been identified. Among these, basic monomers and the so-called co-monomers are most often reported. The substances released from polymer-based materials demonstrate allergenic, cytotoxic, genotoxic, mutagenic, embryotoxic, teratogenic, and estrogenic properties. The aim of this study was to measure the amounts of triethylene glycol dimethacrylate (TEGDMA) and urethane dimethacrylate (UDMA) monomers released from composite dental fillings to citrate-phosphate buffer with the pH of 4, 6, 8 after 24 h and 6 months from the polymerization. Ten samples for each polymerization method had been made from the composite material (Filtek Supreme XT, 3M ESPE, St. Paul, USA), which underwent polymerization using the following lamps: halogen lamp (Translux CL, Heraeus Kulzer, Hanau, Germany) (sample H) and diode lamp (Elipar Freelight 2, 3M ESPE), with soft start function (group DS) and without that function (group DWS). It has been demonstrated that the type of light-curing units has a significant impact on the amount of TEGDMA and UDMA released. The amount of UDMA and TEGDMA monomers released from composite fillings differed significantly depending on the source of polymerization applied, as well as the pH of the solution and sample storage time. Elution of the monomers from composite material polymerized using halogen lamp was significantly greater as compared to curing with diode lamps.

Operational control of material release and discharges from nuclear power plant

International Nuclear Information System (INIS)

Szabo, I. C.; Ranga, T.; Daroczi, L.; Deme, S.; Kerekes, A.

2003-01-01

The operational control of radioactive materials during atmospheric release and aquatic discharge from nuclear power plant is a licensing criterion for NPPs. Originally at the Paks NPP the release control was based on activity limits for four groups of elements. These groups were noble gases, long living radio-aerosols, radioiodine and radiostrontium for atmospheric release and specified activity limit for beta emitters, strontium and tritium for aquatic discharge into Danube. These groups were controlled with proper sampling and/or measuring instrumentation. The limit for atmospheric release was given as a 30-day moving average, for liquid discharges the annual limit was stipulated. The new release and discharge limitation system is based on the environmental dose limitation. The dose constraint for Paks NPP is 90 Sv/year of the critical group for all release pathways and the investigation dose limit is equal to 27 Sv/year. The regulation did not subdivide the dose limit for atmospheric and liquid components but for operational control subdivision of dose limits for atmospheric release and aquatic discharge and shorter time period (one day-one month) seems to be useful. The subdivision can be based on past release data and/or previous activity limits. To satisfy dose below the investigation dose limit there should be a proper operation control level for each separately measured component and pathway belonging to reasonable time interval significantly shorter than one year. The main task of the NPP staff is elaboration of reasonable control levels and reference time intervals for different radionuclide and element groups to be used in operational control. Operational control levels are based on measured daily or monthly release rates. In case of noble gases, aerosols and iodine the daily release rates have several sharp peaks per year. Operational control levels give opportunity to detect these peaks for internal investigation purposes. Investigation release limits

New approaches to deriving limits of the release of radioactive material into the environment

International Nuclear Information System (INIS)

Lindell, B.

1977-01-01

During the last few years, new principles have been developed for the limitation of the release of radioactive material into the environment. It is no longer considered appropriate to base the limitation on limits for the concentrations of the various radionuclides in air and water effluents. Such limits would not prevent large amounts of radioactive material from reaching the environment should effluent rates be high. A common practice has been to identify critical radionuclides and critical pathways and to base the limitation on authorized dose limits for local ''critical groups''. If this were the only limitation, however, larger releases could be permitted after installing either higher stacks or equipment to retain the more short-lived radionuclides for decay before release. Continued release at such limits would then lead to considerably higher exposure at a distance than if no such installation had been made. Accordingly there would be no immediate control of overlapping exposures from several sources, nor would the system guarantee control of the future situation. The new principles described in this paper take the future into account by limiting the annual dose commitments rather than the annual doses. They also offer means of controlling the global situation by limiting not only doses in critical groups but also global collective doses. Their objective is not only to ensure that individual dose limits will always be respected but also to meet the requirement that ''all doses be kept as low as reasonably achievable''. The new approach is based on the most recent recommendations by the ICRP and has been described in a report by an IAEA panel (Procedures for establishing limits for the release of radioactive material into the environment). It has been applied in the development of new Swedish release regulations, which illustrate some of the problems which arise in the practical application

New approaches to deriving limits of the release of radioactive material into the environment

International Nuclear Information System (INIS)

Lindell, B.

1977-01-01

During the last few years, new principles have been developed for the limitation of the release of radioactive material into the environment. It is no longer considered appropriate to base the limitation on limits for the concentrations of the various radionuclides in air and water effluents. Such limits would not prevent large amounts of radioactive material from reaching the environment should effluent rates be high. A common practice has been to identify critical radionuclides and critical pathways and to base the limitation on authorized dose limits for local ''critical groups''. If this were the only limitation, however, larger releases could be permitted after installing either higher stacks or equipment to retain the more shortlived radionuclides for decay before release. Continued release at such limits would then lead to considerably higher exposure at a distance than if no such installation had been made. Accordingly there would be no immediate control of overlapping exposures from several sources, nor would the system guarantee control of the future situation. The new principles described in this paper take the future into account by limiting the annual dose commitments rather than the annual doses. They also offer means of controlling the global situation by limiting not only doses in critical groups but also global collective doses. Their objective is not only to ensure that individual dose limits will always be respected but also to meet the requirement that ''all doses be kept as low as reasonably achievable''. The new approach is based on the most recent recommendations by the ICRP and has been described in a report by an IAEA panel (Procedures for Establishing Limits for the Release of Radioactive Material into the Environment). It has been applied in the development of new Swedish release regulations, which illustrate some of the problems which arise in the practical application. (author)

Determination of accident related release data

International Nuclear Information System (INIS)

Koch, W.; Nolte, O.; Lange, F.; Martens, R.

2004-01-01

For accident safety analyses, for the assessment of potential radiological consequences, for the review of current requirements of the Transport Regulations and for their possible further development as well as for the demonstration that radioactive materials such as LDM candidate material fulfil the regulatory requirements reliable release data following mechanical impact are required. This is definitely one of the demanding issues in the field of transport safety of radioactive materials. In this context special attention has to be paid to radioactive wastes immobilised in brittle materials, e.g. cement/concrete, glass, ceramics or other brittle materials such as fresh and spent fuel. In this presentation we report on a long-term experimental program aiming at improving the general physical understanding of the release process as well as the quantity and the quality of release data. By combining laboratory experiments using small scale test specimens with a few key scaling experiments with large scale test objects significant progress was achieved to meet this objective. The laboratory equipment enables the in-situ determination of the amount and aerodynamic size distribution of the airborne particles generated upon impact of the test specimen on a hard target. Impact energies cover the range experienced in transport accidents including aircraft accidents. The well defined experimental boundary conditions and the good reproducibility of the experimental procedure allowed for systematic studies to exactly measure the amount and aerodynamic size distribution of the airborne release and to quantify its dependence on relevant parameters such as energy input, material properties, and specimen geometry. The experimental program was performed within the scope of various national and international (e.g. EU-funded) projects. The small scale experiments with brittle materials revealed a pronounced universality of the airborne release in view of the material properties and

Electrical conduction in solid materials physicochemical bases and possible applications

CERN Document Server

Suchet, J P

2013-01-01

Electrical Conduction in Solid Materials (Physicochemical Bases and Possible Applications) investigates the physicochemical bases and possible applications of electrical conduction in solid materials, with emphasis on conductors, semiconductors, and insulators. Topics range from the interatomic bonds of conductors to the effective atomic charge in conventional semiconductors and magnetic transitions in switching semiconductors. Comprised of 10 chapters, this volume begins with a description of electrical conduction in conductors and semiconductors, metals and alloys, as well as interatomic bon

Development and evaluation of a biocide release system for prolonged antifungal activity in finishing materials

NARCIS (Netherlands)

Eversdijk, J.; Erich, S.J.F.; Hermanns, S.P.M.; Adan, O.C.G.; Bolle, de M.; Meyer, de K.; Bylemans, D.; Bekker, M.; Cate, ten A.T.

2012-01-01

This paper focuses on the use of modified nano-clay particles as a controlled release system for biocides from building materials. Different (model) biocides were incorporated in a biocide/nano-clay composite and subsequently the release of the biocides was monitored under different environmental

Release of corrosion products from construction materials containing cobalt. Pt.2: Inconel X750

International Nuclear Information System (INIS)

Falk, I.

1978-02-01

This report describes experimental work aimed at determining the release rate for corrosion products from 18Cr8Ni steel and Inconel X750 in BWR environments. For test purposes these environments were simulated in a high pressure loop, where irradiated samples of the materials were exposed for 720 hours. The amounts of released products were determined using gamma spectrometric analysis. The results show that the release from Inconel X750 is higher than that from 18Cr8Ni steel. The release calculated from Co58 measurements is 7 times higher and from Co60 measurements it is 1.5 times higher. Both the filtered and the deposited fractions of the released corrosion products exhibit the same relative concentrations of Co58 and Co60. (author)

A biocompatible hybrid material with simultaneous calcium and strontium release capability for bone tissue repair

Energy Technology Data Exchange (ETDEWEB)

Almeida, J. Carlos [CICECO — Aveiro Institute of Materials, Department of Materials and Ceramic Engineering, University of Aveiro, 3810-193 Aveiro (Portugal); Wacha, András [Research Centre for Natural Sciences, Hungarian Academy of Sciences, Magyar Tudósok körútja 2, Budapest 1117 (Hungary); Gomes, Pedro S. [Laboratory for Bone Metabolism and Regeneration, Faculdade de Medicina Dentária, Universidade do Porto (Portugal); Alves, Luís C. [C2TN, Instituto Superior Técnico, Universidade de Lisboa, E.N.10, 2695-066 Bobadela LRS (Portugal); Fernandes, M. Helena Vaz [CICECO — Aveiro Institute of Materials, Department of Materials and Ceramic Engineering, University of Aveiro, 3810-193 Aveiro (Portugal); Salvado, Isabel M. Miranda, E-mail: isabelmsalvado@ua.pt [CICECO — Aveiro Institute of Materials, Department of Materials and Ceramic Engineering, University of Aveiro, 3810-193 Aveiro (Portugal); Fernandes, M. Helena R. [Laboratory for Bone Metabolism and Regeneration, Faculdade de Medicina Dentária, Universidade do Porto (Portugal)

2016-05-01

The increasing interest in the effect of strontium in bone tissue repair has promoted the development of bioactive materials with strontium release capability. According to literature, hybrid materials based on the system PDMS–SiO{sub 2} have been considered a plausible alternative as they present a mechanical behavior similar to the one of the human bone. The main purpose of this study was to obtain a biocompatible hybrid material with simultaneous calcium and strontium release capability. A hybrid material, in the system PDMS–SiO{sub 2}–CaO–SrO, was prepared with the incorporation of 0.05 mol of titanium per mol of SiO{sub 2}. Calcium and strontium were added using the respective acetates as sources, following a sol–gel technique previously developed by the present authors. The obtained samples were characterized by FT-IR, solid-state NMR, and SAXS, and surface roughness was analyzed by 3D optical profilometry. In vitro studies were performed by immersion of the samples in Kokubo's SBF for different periods of time, in order to determine the bioactive potential of these hybrids. Surfaces of the immersed samples were observed by SEM, EDS and PIXE, showing the formation of calcium phosphate precipitates. Supernatants were analyzed by ICP, revealing the capability of the material to simultaneously fix phosphorus ions and to release calcium and strontium, in a concentration range within the values reported as suitable for the induction of the bone tissue repair. The material demonstrated to be cytocompatible when tested with MG63 osteoblastic cells, exhibiting an inductive effect on cell proliferation and alkaline phosphatase activity. - Highlights: • A hybrid PDMS–SiO{sub 2}–CaO–SrO material was prepared with the incorporation of Ti. • Sr was released in concentrations suitable for the induction of bone tissue repair. • The material demonstrated to be cytocompatible when tested with osteoblastic cells.

Towards a Spiderman suit: large invisible cables and self-cleaning releasable superadhesive materials

International Nuclear Information System (INIS)

Pugno, Nicola M

2007-01-01

Spiders can produce cobwebs with high strength to density ratio and surprisingly display self-cleaning, strong and releasable adhesion (like geckos). Nanointerlocking, capillary and van der Waals forces, all potential adhesive mechanisms, are thus discussed, demonstrating the key role played by hierarchy in the design of superhydrophobic, i.e. self-cleaning (dry or wet and enhanced by activating Fakir drops as in lotus leaves) and superadhesive materials. The reversibility of the strong attachment is quantified thanks to an improved nonlinear peeling model including friction, for which the solution in closed form is provided. Thus, mimicking nature, thanks to carbon-nanotube-based technology, we suggest the feasibility of large invisible cables, as well as of self-cleaning, superadhesive and releasable hierarchical smart materials. We found that a man can theoretically be supported by a transparent cable with cross-section of 1 cm 2 and feasibly, with spider material gloves and boots, could remain attached even to a ceiling: a preliminary step towards a Spiderman suit

Towards a Spiderman suit: large invisible cables and self-cleaning releasable superadhesive materials

Science.gov (United States)

Pugno, Nicola M.

2007-10-01

Spiders can produce cobwebs with high strength to density ratio and surprisingly display self-cleaning, strong and releasable adhesion (like geckos). Nanointerlocking, capillary and van der Waals forces, all potential adhesive mechanisms, are thus discussed, demonstrating the key role played by hierarchy in the design of superhydrophobic, i.e. self-cleaning (dry or wet and enhanced by activating Fakir drops as in lotus leaves) and superadhesive materials. The reversibility of the strong attachment is quantified thanks to an improved nonlinear peeling model including friction, for which the solution in closed form is provided. Thus, mimicking nature, thanks to carbon-nanotube-based technology, we suggest the feasibility of large invisible cables, as well as of self-cleaning, superadhesive and releasable hierarchical smart materials. We found that a man can theoretically be supported by a transparent cable with cross-section of 1 cm2 and feasibly, with spider material gloves and boots, could remain attached even to a ceiling: a preliminary step towards a Spiderman suit.

Towards a Spiderman suit: large invisible cables and self-cleaning releasable superadhesive materials

Energy Technology Data Exchange (ETDEWEB)

Pugno, Nicola M [Department of Structural Engineering, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Turin (Italy)

2007-10-03

Spiders can produce cobwebs with high strength to density ratio and surprisingly display self-cleaning, strong and releasable adhesion (like geckos). Nanointerlocking, capillary and van der Waals forces, all potential adhesive mechanisms, are thus discussed, demonstrating the key role played by hierarchy in the design of superhydrophobic, i.e. self-cleaning (dry or wet and enhanced by activating Fakir drops as in lotus leaves) and superadhesive materials. The reversibility of the strong attachment is quantified thanks to an improved nonlinear peeling model including friction, for which the solution in closed form is provided. Thus, mimicking nature, thanks to carbon-nanotube-based technology, we suggest the feasibility of large invisible cables, as well as of self-cleaning, superadhesive and releasable hierarchical smart materials. We found that a man can theoretically be supported by a transparent cable with cross-section of 1 cm{sup 2} and feasibly, with spider material gloves and boots, could remain attached even to a ceiling: a preliminary step towards a Spiderman suit.

Stability and in vitro release profile of enalapril maleate from different commercially available tablets: possible therapeutic implications.

Science.gov (United States)

Lima, Dione Marçal; dos Santos, Leandro Dias; Lima, Eliana Martins

2008-08-05

Stability of enalapril maleate formulations can be affected when the product is exposed to higher temperature and humidity, with the formation of two main degradation products: enalaprilat and a diketopiperazine derivative. In this work, stability and drug release profiles of 20 mg enalapril maleate tablets (reference, generic and similar products) were evaluated. After 180 days of the accelerated stability testing, most products did not exhibit the specified amount of drug. Additionally, drug release profiles were markedly different from that of the reference product, mainly due to drug degradation. Changes in drug concentration and drug release profile of enalapril formulations are strong indicators of a compromised bioavailability, with possible interferences on the therapeutic response for this drug.

Impact of physicochemical properties of porous silica materials conjugated with dexamethasone via pH-responsive hydrazone bond on drug loading and release behavior

Science.gov (United States)

Numpilai, Thanapha; Witoon, Thongthai; Chareonpanich, Metta; Limtrakul, Jumras

2017-02-01

The conjugation of dexamethasone (DEX) onto modified-porous silica materials via a pH-responsive hydrazone bond has been reported to be highly efficient method to specifically deliver the DEX to diseased sites. However, the influence of physicochemical properties of porous silica materials has not yet been fully understood. In this paper, the impact of pore sizes, particle sizes and silanol contents on surface functionalization, drug loading and release behavior of porous silica materials conjugated with dexamethasone via pH-responsive hydrazone bond was investigated. The grafting density was found to relate to the number of silanol groups on the surface of porous silica materials. The particle size and macropores of the porous silica materials played an vital role on the drug loading and release behavior. Although the porous silica materials with larger particle sizes possessed a lower grafting density, a larger amount of drug loading could be achieved. Moreover, the porous silica materials with larger particle sizes showed a slower release rate of DEX due to a longer distance for cleaved DEX diffusion out of pores. DEX release rate exhibited pH-dependent, sustained release. At pH 4.5, the amount of DEX release within 10 days could be controlled in the range of 12.74-36.41%, depending on the host material. Meanwhile, less than 1.5% of DEX was released from each of type of the porous silica materials at pH 7.4. The results of silica dissolution suggested that the degradation of silica matrix did not significantly affect the release rate of DEX. In addition, the kinetic modeling studies revealed that the DEX releases followed Korsmeyer-Peppas model with a release exponent (n) ranged from 0.3 to 0.47, indicating a diffusion-controlled release mechanism.

ENERGY RELEASE FROM IMPACTING PROMINENCE MATERIAL FOLLOWING THE 2011 JUNE 7 ERUPTION

Energy Technology Data Exchange (ETDEWEB)

Gilbert, H. R.; Inglis, A. R.; Mays, M. L.; Ofman, L.; Thompson, B. J.; Young, C. A. [Solar Physics Laboratory, Heliophysics Science Division, NASA Goddard Space Flight Center, Greenbelt, MD 20771 (United States)

2013-10-10

Solar filaments exhibit a range of eruptive-like dynamic activity, ranging from the full or partial eruption of the filament mass and surrounding magnetic structure as a coronal mass ejection to a fully confined or failed eruption. On 2011 June 7, a dramatic partial eruption of a filament was observed by multiple instruments on board the Solar Dynamics Observatory (SDO) and Solar-Terrestrial Relations Observatory. One of the interesting aspects of this event is the response of the solar atmosphere as non-escaping material falls inward under the influence of gravity. The impact sites show clear evidence of brightening in the observed extreme ultraviolet wavelengths due to energy release. Two plausible physical mechanisms for explaining the brightening are considered: heating of the plasma due to the kinetic energy of impacting material compressing the plasma, or reconnection between the magnetic field of low-lying loops and the field carried by the impacting material. By analyzing the emission of the brightenings in several SDO/Atmospheric Imaging Assembly wavelengths, and comparing the kinetic energy of the impacting material (7.6 × 10{sup 26}-5.8 × 10{sup 27} erg) to the radiative energy (≈1.9 × 10{sup 25}-2.5 × 10{sup 26} erg), we find the dominant mechanism of energy release involved in the observed brightening is plasma compression.

Energy Release from Impacting Prominence Material Following the 2011 June 7 Eruption

Science.gov (United States)

Gilbert, H. R.; Inglis, A. R.; Mays, M. L.; Ofman, L.; Thompson, B. J.; Young, C. A.

2013-01-01

Solar filaments exhibit a range of eruptive-like dynamic activity, ranging from the full or partial eruption of the filament mass and surrounding magnetic structure as a coronal mass ejection to a fully confined or failed eruption. On 2011 June 7, a dramatic partial eruption of a filament was observed by multiple instruments on board the Solar Dynamics Observatory (SDO) and Solar-Terrestrial Relations Observatory. One of the interesting aspects of this event is the response of the solar atmosphere as non-escaping material falls inward under the influence of gravity. The impact sites show clear evidence of brightening in the observed extreme ultraviolet wavelengths due to energy release. Two plausible physical mechanisms for explaining the brightening are considered: heating of the plasma due to the kinetic energy of impacting material compressing the plasma, or reconnection between the magnetic field of low-lying loops and the field carried by the impacting material. By analyzing the emission of the brightenings in several SDO/Atmospheric Imaging Assembly wavelengths, and comparing the kinetic energy of the impacting material (7.6 × 10(exp 26) - 5.8 × 10(exp 27) erg) to the radiative energy (approx. 1.9 × 10(exp 25) - 2.5 × 10(exp 26) erg), we find the dominant mechanism of energy release involved in the observed brightening is plasma compression.

Tritium release from advanced beryllium materials after loading by tritium/hydrogen gas mixture

Energy Technology Data Exchange (ETDEWEB)

Chakin, Vladimir, E-mail: vladimir.chakin@kit.edu [Karlsruhe Institute of Technology, Institute for Applied Materials, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Rolli, Rolf; Moeslang, Anton; Kurinskiy, Petr; Vladimirov, Pavel [Karlsruhe Institute of Technology, Institute for Applied Materials, Hermann-von-Helmholtz-Platz 1, 76344 Eggenstein-Leopoldshafen (Germany); Dorn, Christopher [Materion Beryllium & Composites, 6070 Parkland Boulevard, Mayfield Heights, OH 44124-4191 (United States); Kupriyanov, Igor [Bochvar Russian Scientific Research Institute of Inorganic Materials, Rogova str., 5, 123098 Moscow (Russian Federation)

2016-06-15

Highlights: • A major tritium release peak for beryllium samples occurs at temperatures higher than 1250 K. • A beryllium grade with comparatively smaller grain size has a comparatively higher tritium release compared to the grade with larger grain size. • The pebbles of irregular shape with the grain size of 10–30 μm produced by the crushing method demonstrate the highest tritium release rate. - Abstract: Comparison of different beryllium samples on tritium release and retention properties after high-temperature loading by tritium/hydrogen gas mixture and following temperature-programmed desorption (TPD) tests has been performed. The I-220-H grade produced by hot isostatic pressing (HIP) having the smallest grain size, the pebbles of irregular shape with the smallest grain size (10–30 μm) produced by the crushing method (CM), and the pebbles with 1 mm diameter produced by the fluoride reduction method (FRM) having a highly developed inherent porosity show the highest release rate. Grain size and porosity are considered as key structural parameters for comparison and ranking of different beryllium materials on tritium release and retention properties.

The possibility of using materials based on secondary gravel in civil construction

Directory of Open Access Journals (Sweden)

Galitskova Yulia

2017-01-01

Full Text Available By now, the wear and tear of housing stock is more than 50%. Each year the number of old and dilapidated housing is growing, but it is gradually replaced by modern buildings. However, wastes accumulated from dismantling of buildings and constructions, are underutilized and, usually are just stored at landfills, or used for temporary roads construction. The purpose of this research is to define construction wastes characteristics and to explore possibilities for recycling of wastes from construction materials production. The paper also analyzes housing stock condition and basic requirements to building materials used in construction; and demonstrates results building materials based on secondary gravel investigation. While working with materials based on waste requirements the authors conducted laboratory research. Thus, the paper presents the analysis of laboratory tests results that made it possible to draw conclusions about the possible use of building materials based on secondary gravel and about their conformity to specified requirements. The researchers also developed proposals and recommendations to improve the competitiveness of such materials.

Fluoride release and recharge behavior of a nano-filled resin-modified glass ionomer compared with that of other fluoride releasing materials.

Science.gov (United States)

Mitra, Sumita B; Oxman, Joe D; Falsafi, Afshin; Ton, Tiffany T

2011-12-01

To compare the long-term fluoride release kinetics of a novel nano-filled two-paste resin-modified glass-ionomer (RMGI), Ketac Nano (KN) with that of two powder-liquid resin-modified glass-ionomers, Fuji II LC (FLC) and Vitremer (VT) and one conventional glass-ionomer, Fuji IX (FIX). Fluoride release was measured in vitro using ion-selective electrodes. Kinetic analysis was done using regression analysis and compared with existing models for GIs and compomers. In a separate experiment the samples of KN and two conventional glass-ionomers, FIX and Ketac Molar (KM) were subjected to a treatment with external fluoride source (Oral-B Neutra-Foam) after 3 months of fluoride release and the recharge behavior studied for an additional 7-day period. The cumulative amount of fluoride released from KN, VT and FLC and the release profiles were statistically similar but greater than that for FIX at P coating of KN with its primer and of DY with its adhesive did not significantly alter the fluoride release behavior of the respective materials. The overall rate for KN was significantly higher than for the compomer DY. DY showed a linear rate of release vs. t and no burst effect as expected for compomers. The nanoionomer KN showed fluoride recharge behavior similar to the conventional glass ionomers FIX and KM. Thus, it was concluded that the new RMGI KN exhibits fluoride ion release behavior similar to typical conventional and RMGIs and that the primer does not impede the release of fluoride.

Sapropel as a Binder: Properties and Application Possibilities for Composite Materials

Science.gov (United States)

Obuka, V.; Šinka, M.; Kļaviņš, M.; Stankeviča, K.; Korjakins, A.

2015-11-01

Recent development trends largely look for possibilities of a wider use of natural materials and local resources. In this perspective, the use of organic rich lake sediment - sapropel - as a binding material in line with other environmentally friendly filling materials can be considered as a challenge. Sapropel itself is a valuable resource with multiple areas of application, for example, medicine, veterinary, agriculture, livestock farming, balneology, cosmetic applications, construction, and its application options have been widely studied in the 20th century in the Baltic countries, Ukraine and Russia. Birch wood fibre and sanding dust, hemp shives, ‘Aerosil’ are used as a filler and three types of sapropel are used as a binder in making composites. After material preparation and curing, physical and mechanical properties - density, thermal conductivity, compressive and flexural strength, were determined and compared to the data in the literature, and the opportunities to use them in the ecological construction were considered. The obtained results give insight into possibilities to use sapropel as a raw material, which can be considered as prospective material for construction materials and design products.

Effect of gamma irradiation on fluoride release and antibacterial activity of resin dental materials

International Nuclear Information System (INIS)

Carvalho, Fabiola Galbiatti de; Fucio, Suzana Beatriz Portugal de; Correr-Sobrinho, Lourenco; Pascon, Fernanda Miori; Kantovitz, Kamila Rosamilia; Puppin-Rontani, Regina Maria

2009-01-01

This study evaluated the effect of gamma irradiation on fluoride release and antibacterial activity of FluroShield (FS) and Clearfil Protect Bond (CPB). Four groups were formed: G1-FS + gamma; G2-FS without gamma; G3-CPB + gamma; G4-CPB without gamma. For fluoride release analysis, 12 disks of each material were prepared and covered with nail polish, except for one side (50.4 mm 2 area). G1 and G3 were sterilized with a 14.5 KGy dose at 27 deg C for 24 h, while G2 and G4 (controls) were not sterilized and were maintained under the same time and temperature conditions. Fluoride release measurements were made in duplicate (n=6) by an ion specific electrode. The antibacterial activity of the CPB and FS against Streptococcus mutans after gamma sterilization was evaluated by the agar-disc diffusion method. The diameter of the zones of microbial growth inhibition was recorded after 48 h. Data were analyzed statistically by ANOVA and Tukey's test (alpha=5%). Gamma sterilization decreased the fluoride release of FS by approximately 50%, while CPB was not affected. There was no statistically significant difference (p>0.05) in the antibacterial effect of CPB between gamma and non-gamma sterilization groups. FS presented no antibacterial activity. Gamma irradiation decreased the fluoride release of FS, but did not affect the antibacterial activity of the studied materials. (author)

Effect of gamma irradiation on fluoride release and antibacterial activity of resin dental materials

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Fabiola Galbiatti de; Fucio, Suzana Beatriz Portugal de; Correr-Sobrinho, Lourenco [Universidade Estadual de Campinas (UNICAMP), Piracicaba, SP (Brazil). Piracicaba Dental School. Dept. of Dental Materials; Pascon, Fernanda Miori; Kantovitz, Kamila Rosamilia; Puppin-Rontani, Regina Maria [Universidade Estadual de Campinas (UNICAMP), Piracicaba, SP (Brazil). Piracicaba Dental School. Dept. of Pedriatric Dentistry], e-mail: rmpuppin@fop.unicamp.br

2009-07-01

This study evaluated the effect of gamma irradiation on fluoride release and antibacterial activity of FluroShield (FS) and Clearfil Protect Bond (CPB). Four groups were formed: G1-FS + gamma; G2-FS without gamma; G3-CPB + gamma; G4-CPB without gamma. For fluoride release analysis, 12 disks of each material were prepared and covered with nail polish, except for one side (50.4 mm{sup 2} area). G1 and G3 were sterilized with a 14.5 KGy dose at 27 deg C for 24 h, while G2 and G4 (controls) were not sterilized and were maintained under the same time and temperature conditions. Fluoride release measurements were made in duplicate (n=6) by an ion specific electrode. The antibacterial activity of the CPB and FS against Streptococcus mutans after gamma sterilization was evaluated by the agar-disc diffusion method. The diameter of the zones of microbial growth inhibition was recorded after 48 h. Data were analyzed statistically by ANOVA and Tukey's test (alpha=5%). Gamma sterilization decreased the fluoride release of FS by approximately 50%, while CPB was not affected. There was no statistically significant difference (p>0.05) in the antibacterial effect of CPB between gamma and non-gamma sterilization groups. FS presented no antibacterial activity. Gamma irradiation decreased the fluoride release of FS, but did not affect the antibacterial activity of the studied materials. (author)

Liberação de flúor de materiais restauradores Fluoride releasing of restorative materials

Directory of Open Access Journals (Sweden)

Adriana Silva de CARVALHO

1998-10-01

Full Text Available Atualmente no mercado odontológico existem diversos tipos de materiais restauradores que liberam flúor com o objetivo de diminuir ou eliminar as cáries recorrentes. Considerando-se a diferença de composição desses materiais, foi avaliada sua capacidade de liberação de flúor. Foram avaliados os materiais restauradores: Chelon-fil (ESPE, Vitremer (3M, Variglass (Dentsply, Dyract (Dentsply e Tetric (Vivadent. Confeccionaram-se seis amostras cilíndricas (área = 1,65 cm2 de cada material, as quais foram imersas individualmente em 2,0 ml de água deionizada, que foi trocada diariamente durante 15 dias. A liberação de flúor foi determinada após adição de volume igual de tampão TISAB II às soluções. Para a análise da concentração de flúor foi utilizado um eletrodo específico para flúor Orion 96-09, acoplado a um analisador de íons Orion EA-940. Todos os materiais seguiram o mesmo padrão de liberação de flúor. As maiores médias de flúor liberado dentro de cada material foram encontradas no 1º dia, decrescendo bruscamente no 2º e 3º dias, e a quantidade de flúor liberado apresentou um decréscimo com o passar dos dias até atingir um nível quase constante. A liberação média de flúor durante o período de avaliação (média e desvio padrão em µg F/cm2 foi: CHE = 7,62 ± 0,76A, VIT = 5,91 ± 0,79B, VAR = 2,72 ± 0,25C, DYR = 1,50 ± 0,17 D, TET = 0,136 ± 0,016 E. Médias seguidas por letras distintas diferem entre si ao nível de significância de 5% (Tukey. Os resultados mostraram que a composição dos materiais restauradores influencia de maneira significativa sua liberação de flúor.Nowadays there are several types of restorative materials with fluoride release properties. Thus, the purpose of this study was to analyze the fluoride release from the following restorative materials, considering their different compositions. The materials used were: Chelon Fil-ESPE (CHE, Vitremer-3M (VIT, Variglass

High-Temperature Release of SO2 from Calcined Cement Raw Materials

DEFF Research Database (Denmark)

Nielsen, Anders Rooma; Larsen, Morten B.; Glarborg, Peter

2011-01-01

During combustion of alternative fuels in the material inlet end of cement rotary kilns, local reducing conditions may occur and cause reductive decomposition of sulfates from calcined cement raw materials. Decomposition of sulfates is problematic because it increases the gas-phase SO2...... concentration, which may cause deposit formation in the kiln system. In this study, the release of sulfur from calcined cement raw materials under both oxidizing and reducing conditions is investigated. The investigations include thermodynamic equilibrium calculations in the temperature interval of 800–1500 °C...... and experiments in a tube furnace reactor in the temperature interval of 900–1100 °C. The investigated conditions resemble actual conditions in the material inlet end of cement rotary kilns. It was found that the sulfates CaSO4, K2SO4, and Na2SO4 were all stable under oxidizing conditions but began to decompose...

Cask for radioactive material and method for preventing release of neutrons from radioactive material

International Nuclear Information System (INIS)

Gaffney, M.F.; Shaffer, P.T.

1981-01-01

A cask for radioactive material, such as nuclear reactor fuel or spent nuclear reactor fuel, includes a plurality of associated walled internal compartments for containing such radioactive material, with neutron absorbing material present to absorb neutrons emitted by the radioactive material, and a plurality of thermally conductive members, such as longitudinal copper or aluminum castings, about the compartment and in thermal contact with the compartment walls and with other such thermally conductive members and having thermal contact surfaces between such members extending, preferably radially, from the compartment walls to external surfaces of the thermally conductive members, which surfaces are preferably in the form of a cylinder. The ends of the shipping cask also preferably include a neutron absorber and a conductive metal covering to dissipate heat released by decay of the radioactive material. A preferred neutron absorber utilized is boron carbide, preferably as plasma sprayed with metal powder or as particles in a matrix of phenolic polymer, and the compartment walls are preferably of stainless steel, copper or other corrosion resistant and heat conductive metal or alloy. The invention also relates to shipping casks, storage casks and other containers for radioactive materials in which a plurality of internal compartments for such material, e.g., nuclear reactor fuel rods, are joined together, preferably in modular construction with surrounding heat conductive metal members, and the modules are joined together to form a major part of a finished shipping cask, which is preferably of cylindrical shape. Also within the invention are methods of safely storing radioactive materials which emit neutrons, while dissipating the heat thereof, and of manufacturing the present shipping casks

Flare Energy Release: Internal Conflict, Contradiction with High Resolution Observations, Possible Solutions

Science.gov (United States)

Pustilnik, L.

2017-06-01

spectrum of distribution of flares and micro-flares, and possibility of phase transition to flare energy release with huge increasing of energy release.

Ciprofloxacin-intercalated Zinc Layered Hydroxides Hybrid Material: Synthesis and in Vitro Release Profiles of an Antibiotic Compound

International Nuclear Information System (INIS)

Mohd Zobir Hussein; Mohd Zobir Hussein; Stanslas, J.; Abdul Halim Abdullah

2011-01-01

The intriguing anion exchange properties of layered hydroxides salts, combined with its high layer charge density have provided strong motivations for the potential use of the inorganic layered host material in drug delivery applications. Ciprofloxacin (CFX), a wide spectrum antibiotic has been anion exchanged with nitrate of zinc hydroxide nitrate (ZHN), which belongs to the LHS family, resulted in the expansion of the basal spacing from 9.92 Amstrom of ZHN to 21.5 Angstrom of ZCFX, the obtained hybrid material. Other characterizations, such as Fourier transform infra red spectroscopy (FTIR), CHNS analysis and TGA/ DTG have further corroborated this finding. Electron microscopy study reveals the plate-like structure of the nano hybrid material. The in vitro release of CFX was performed in phosphate saline buffer at pH 7.4 and it behaves in a slow and sustained release profile over a period of 72 hours. This study suggests that ZHN, which demonstrates a controlled release behavior, could be a potential host material in the drug delivery applications. (author)

Regulatory analysis on criteria for the release of patients administered radioactive material. Final report

Energy Technology Data Exchange (ETDEWEB)

Schneider, S.; McGuire, S.A.

1997-02-01

This regulatory analysis was developed to respond to three petitions for rulemaking to amend 10 CFR parts 20 and 35 regarding release of patients administered radioactive material. The petitions requested revision of these regulations to remove the ambiguity that existed between the 1-millisievert (0.1-rem) total effective dose equivalent (TEDE) public dose limit in Part 20, adopted in 1991, and the activity-based release limit in 10 CFR 35.75 that, in some instances, would permit release of individuals in excess of the current public dose limit. Three alternatives for resolution of the petitions were evaluated. Under Alternative 1, NRC would amend its patient release criteria in 10 CFR 35.75 to match the annual public dose limit in Part 20 of 1 millisievert (0.1 rem) TEDE. Alternative 2 would maintain the status quo of using the activity-based release criteria currently found in 10 CFR 35.75. Under Alternative 3, the NRC would revise the release criteria in 10 CFR 35.75 to specify a dose limit of 5 millisieverts (0.5 rem) TEDE.

Regulatory analysis on criteria for the release of patients administered radioactive material. Final report

International Nuclear Information System (INIS)

Schneider, S.; McGuire, S.A.

1997-02-01

This regulatory analysis was developed to respond to three petitions for rulemaking to amend 10 CFR parts 20 and 35 regarding release of patients administered radioactive material. The petitions requested revision of these regulations to remove the ambiguity that existed between the 1-millisievert (0.1-rem) total effective dose equivalent (TEDE) public dose limit in Part 20, adopted in 1991, and the activity-based release limit in 10 CFR 35.75 that, in some instances, would permit release of individuals in excess of the current public dose limit. Three alternatives for resolution of the petitions were evaluated. Under Alternative 1, NRC would amend its patient release criteria in 10 CFR 35.75 to match the annual public dose limit in Part 20 of 1 millisievert (0.1 rem) TEDE. Alternative 2 would maintain the status quo of using the activity-based release criteria currently found in 10 CFR 35.75. Under Alternative 3, the NRC would revise the release criteria in 10 CFR 35.75 to specify a dose limit of 5 millisieverts (0.5 rem) TEDE

Influence of the conditional release of the materials with very low level of radioactivity on the environment - 59132

International Nuclear Information System (INIS)

Prvakova, Slavka; Mrskova, Adela; Pritrsky, Jozef

2012-01-01

Significant amount of solid materials (metals, non-metals, building structures) that could be contaminated or activated is produced during operation and especially decommissioning of nuclear power plants. Considerable fraction of these materials has level of radioactivity close to the radiological limits allowing its safe release into the environment thereby could be potentially recycled within the special constructions, as for example tunnels, roads or bridges. If the requirements of legislation on the radiological limits for handling such material and long-term safety of the constructions are met, contaminated material can be incorporated in the form of recycled concrete, remelted steel, etc. The paper presents implementation of the IAEA and EC recommendations into the form of detailed analytical approaches with the aim to develop integrated scenarios and to analyse long-term influence of the conditional release of the material with very low level of radioactivity on the environment. Further, an estimation of the key input parameters characteristic for the specific conditions of Slovak case in order to fulfil the radiological limits according to the Slovak legislation is included. Analysed integrated scenarios represent surface or underground civil construction with radionuclides released directly into the geosphere and transported by a groundwater flow to the biosphere. The migration of radionuclides is modelled in the near-surface conditions with the advection as a dominant transport mechanism. Computer code GoldSim is used to evaluate the long-term safety assessment of the conditionally released material on the environment. (authors)

Radionuclide release from simulated waste material after biogeochemical leaching of uraniferous mineral samples

International Nuclear Information System (INIS)

Williamson, Aimee Lynn; Caron, François; Spiers, Graeme

2014-01-01

Biogeochemical mineral dissolution is a promising method for the released of metals in low-grade host mineralization that contain sulphidic minerals. The application of biogeochemical mineral dissolution to engineered leach heap piles in the Elliot Lake region may be considered as a promising passive technology for the economic recovery of low grade Uranium-bearing ores. In the current investigation, the decrease of radiological activity of uraniferous mineral material after biogeochemical mineral dissolution is quantified by gamma spectroscopy and compared to the results from digestion/ICP-MS analysis of the ore materials to determine if gamma spectroscopy is a simple, viable alternative quantification method for heavy nuclides. The potential release of Uranium (U) and Radium-226 ( 226 Ra) to the aqueous environment from samples that have been treated to represent various stages of leaching and passive closure processes are assessed. Dissolution of U from the solid phase has occurred during biogeochemical mineral dissolution in the presence of Acidithiobacillus ferrooxidans, with gamma spectroscopy indicating an 84% decrease in Uranium-235 ( 235 U) content, a value in accordance with the data obtained by dissolution chemistry. Gamma spectroscopy data indicate that only 30% of the 226 Ra was removed during the biogeochemical mineral dissolution. Chemical inhibition and passivation treatments of waste materials following the biogeochemical mineral dissolution offer greater protection against residual U and 226 Ra leaching. Pacified samples resist the release of 226 Ra contained in the mineral phase and may offer more protection to the aqueous environment for the long term, compared to untreated or inhibited residues, and should be taken into account for future decommissioning. - Highlights: • Gamma counting showed an 84% decrease in 235 U after biogeochemical mineral leaching. • Chemical digestion/ICP-MS analysis also showed an 84% decrease in total U. • Over

Ion release from magnesium materials in physiological solutions under different oxygen tensions.

Science.gov (United States)

Feyerabend, Frank; Drücker, Heiko; Laipple, Daniel; Vogt, Carla; Stekker, Michael; Hort, Norbert; Willumeit, Regine

2012-01-01

Although magnesium as degradable biomaterial already showed clinical proof of concepts, the design of new alloys requires predictive in vitro methods, which are still lacking. Incubation under cell culture conditions to obtain "physiological" corrosion may be a solution. The aim of this study was to analyse the influence of different solutions, addition of proteins and of oxygen availability on the corrosion of different magnesium materials (pure Mg, WE43, and E11) with different surface finishing. Oxygen content in solution, pH, osmolality and ion release were determined. Corrosion led to a reduction of oxygen in solution. The influence of oxygen on pH was enhanced by proteins, while osmolality was not influenced. Magnesium ion release was solution-dependent and enhanced in the initial phase by proteins with delayed release of alloying elements. The main corrosion product formed was magnesium carbonate. Therefore, cell culture conditions are proposed as first step toward physiological corrosion.

Analyse of possibilities of increasing housing energy efficiency by application of phase-changing materials

Directory of Open Access Journals (Sweden)

Vučeljić-Vavan Sanja

2009-01-01

Full Text Available Refurbishment of existing building stock using energy-saving phase-changing smart materials and technologies, in addition to improved indoor climatic conditions, offer an opportunity for increasing housing energy efficiency and value. This fast developing technology becomes increasingly cost-effective with much shorter payback periods. However, it is undertaken only on a limited scale; because of lack of knowledge about their changeable properties and dynamism in that they behave in response to energy fields. Main characteristics, which make them different form others, are: immediacy transience, self-actuation, selectivity and directness. Phase change processes invariably involve the absorbing, storing or releasing of large amounts of energy in the form of latent heat. These processes are reversible and phase-changing materials can undergo an unlimited number of cycles without degradation. Since phase-changing materials can be designed to absorb or release energy at predictable temperatures, they have naturally been explored for use in architecture as a way of helping deal with the thermal environment in a building. Technologies based on sealing phase-changing materials into small pellets have achieved widespread use in connection with radiant floor heating systems, phase change wallboards, mortar or facade systems. Thermal characteristics of existing buildings can be improved on increasing their thermal-stored mass by implementation products of phase-changing smart materials. In addition to contributing to carbon reduction and energy security, using phase-changing materials in the building sector stimulates innovations.

Principles for limiting releases of radioactive effluents into the environment

International Nuclear Information System (INIS)

1986-01-01

This publication is concerned with the subject of limiting releases of radioactive effluents during normal, controlled operation of nuclear installations. It does not deal with releases from accidents where it is only possible to limit exposures by intervention. In 1978 the IAEA published guidance on the concepts and principles for use by the competent authorities in setting limits for planned releases of radioactive material into the environment (Safety Series No. 45). This publication is a complete revision of Safety Series No. 45 and its Annex

PWR-GALE, Radioactive Gaseous Release and Liquid Release from PWR

International Nuclear Information System (INIS)

Chandrasekaran, T.; Lee, J.Y.; Willis, C.A.

1988-01-01

1 - Description of program or function: The PWR-GALE (Boiling Water Reactor Gaseous and Liquid Effluents) Code is a computerized mathematical model for calculating the release of radioactive material in gaseous and liquid effluents from pressurized water reactors (PWRs). The calculations are based on data generated from operating reactors, field tests, laboratory tests, and plant-specific design considerations incorporated to reduce the quantity of radioactive materials that may be released to the environment. 2 - Method of solution: GALE calculates expected releases based on 1) standardized coolant activities derived from ANS Standards 18.1 Working Group recommendations, 2) release and transport mechanisms that result in the appearance of radioactive material in liquid and gaseous waste streams, 3) plant-specific design features used to reduce the quantities of radioactive materials ultimately released to the environs, and 4) information received on the operation of nuclear power plants. 3 - Restrictions on the complexity of the problem: The liquid release portion of GALE uses subroutines taken from the ORIGEN (CCC-217) to calculate radionuclide buildup and decay during collection, processing, and storage of liquid radwaste. Memory requirements for this part of the program are determined by the large nuclear data base accessed by these subroutines

Possibilities for in-vitro testing of controlled-release parenterals.

OpenAIRE

Kožák, Jan

2014-01-01

The objective of this study was to start with the development of a gel-based medium simulating intramuscular environment for in-vitro drug release testing as an alternative to currently used water-based media. A pork meat was selected as a model of the muscle tissue. At the first part of the study, diffusion rate was proposed as the most determining factor of drug release in gel-based medium. Consequently, the diffusion rate of sodium fluorescein in pork meat was compared with the diffusion r...

An In-Vitro Study on the Release of Fluoride from Two Restorative Materials and Their Rechargeability after Exposure to Daily 1000 ppm Fluoride

Directory of Open Access Journals (Sweden)

A. Kowsari

2005-09-01

Full Text Available Statement of Problem: Since the fluoride releases from materials with the property of releasing fluoride are decreasing gradually, it seems that probably the material rechargeability is more important than their long-term fluoride release.Purpose: the objective of this study was to asses the fluoride release and rechargeability of 2 types of fluoride releasing restorative materials, a resin modified glass ionomer(Vitremer and a compomer (Compoglass F, after exposure to daily NaF solutionscontaining 1000 ppm F, for 1 minute.Materials and Methods: Twelve discs ( 8 mm ×2 mm of each of the materials were fabricated, and divided into 2 groups (test and control. All discs were stored in 4 mL artificial saliva at 37°C. In group 1 (N=6, the specimens were immersed in artificialsaliva which was changed daily for 25 days. In group 2 (N=6, in addition to receiving the same treatment as group 1, the specimens were immersed in NaF solution (1000ppm F, ph=6.9 for 1 minute before daily saliva change. A potentiometer was used to determine the amount of fluoride released on days 1, 2, 3, 5, 10, 15, 20 and 25, after the daily saliva change, in all study groups. Data were analyzed by the t-student test after confirmation of the equality of variances by Leven’s test.Results: Both materials continued releasing fluoride throughout the whole study period. For each material, the release was highest on day one. During the first 3 days,glass ionomer released significantly higher amounts of fluoride as compared to compomer (p0.05. After exposure to NaF solution, none of the materials showed statistically significant rechargeability (p>0.05 and the amount of fluoride-releasecontinued to drop during the study period in similar patterns for both the test and the control groups.Conclusion: It may be concluded that rechargeability of glass ionomer and compomer,using daily neutral fluoride mouth rinses and toothpastes does not occur in reliable amounts.

Preparation of thermo-sensitive slow releasing material and its application in low tar tobacco

Directory of Open Access Journals (Sweden)

Tian Zhong

2017-04-01

Full Text Available To solve some sensory defects such as fragrance deficiency,strong dry sense,poor satisfaction in the development of ultra-low tar tobacco products,we prepared a new thermo sensitive slow releasing composite material with tobacco aroma.The characterization results showed that the as-prepared thermosensitive particles have better aroma enhancing and slow releasing effects.Also,the aroma components of the tip stick containing thermosensitive particles were detected and its sensory quality was evaluated.The results showed that composite tip stick could enhance the aroma and improve the sensory quality of the cigarettes.

Geochemistry Model Validation Report: Material Degradation and Release Model

Energy Technology Data Exchange (ETDEWEB)

H. Stockman

2001-09-28

The purpose of this Analysis and Modeling Report (AMR) is to validate the Material Degradation and Release (MDR) model that predicts degradation and release of radionuclides from a degrading waste package (WP) in the potential monitored geologic repository at Yucca Mountain. This AMR is prepared according to ''Technical Work Plan for: Waste Package Design Description for LA'' (Ref. 17). The intended use of the MDR model is to estimate the long-term geochemical behavior of waste packages (WPs) containing U. S . Department of Energy (DOE) Spent Nuclear Fuel (SNF) codisposed with High Level Waste (HLW) glass, commercial SNF, and Immobilized Plutonium Ceramic (Pu-ceramic) codisposed with HLW glass. The model is intended to predict (1) the extent to which criticality control material, such as gadolinium (Gd), will remain in the WP after corrosion of the initial WP, (2) the extent to which fissile Pu and uranium (U) will be carried out of the degraded WP by infiltrating water, and (3) the chemical composition and amounts of minerals and other solids left in the WP. The results of the model are intended for use in criticality calculations. The scope of the model validation report is to (1) describe the MDR model, and (2) compare the modeling results with experimental studies. A test case based on a degrading Pu-ceramic WP is provided to help explain the model. This model does not directly feed the assessment of system performance. The output from this model is used by several other models, such as the configuration generator, criticality, and criticality consequence models, prior to the evaluation of system performance. This document has been prepared according to AP-3.10Q, ''Analyses and Models'' (Ref. 2), and prepared in accordance with the technical work plan (Ref. 17).

Geochemistry Model Validation Report: Material Degradation and Release Model

International Nuclear Information System (INIS)

Stockman, H.

2001-01-01

The purpose of this Analysis and Modeling Report (AMR) is to validate the Material Degradation and Release (MDR) model that predicts degradation and release of radionuclides from a degrading waste package (WP) in the potential monitored geologic repository at Yucca Mountain. This AMR is prepared according to ''Technical Work Plan for: Waste Package Design Description for LA'' (Ref. 17). The intended use of the MDR model is to estimate the long-term geochemical behavior of waste packages (WPs) containing U. S . Department of Energy (DOE) Spent Nuclear Fuel (SNF) codisposed with High Level Waste (HLW) glass, commercial SNF, and Immobilized Plutonium Ceramic (Pu-ceramic) codisposed with HLW glass. The model is intended to predict (1) the extent to which criticality control material, such as gadolinium (Gd), will remain in the WP after corrosion of the initial WP, (2) the extent to which fissile Pu and uranium (U) will be carried out of the degraded WP by infiltrating water, and (3) the chemical composition and amounts of minerals and other solids left in the WP. The results of the model are intended for use in criticality calculations. The scope of the model validation report is to (1) describe the MDR model, and (2) compare the modeling results with experimental studies. A test case based on a degrading Pu-ceramic WP is provided to help explain the model. This model does not directly feed the assessment of system performance. The output from this model is used by several other models, such as the configuration generator, criticality, and criticality consequence models, prior to the evaluation of system performance. This document has been prepared according to AP-3.10Q, ''Analyses and Models'' (Ref. 2), and prepared in accordance with the technical work plan (Ref. 17)

Fluorine uptake into the human tooth from a thin layer of F-releasing material

International Nuclear Information System (INIS)

Yamamoto, H.; Nomachi, M.; Yasuda, K.; Iwami, Y.; Ebisu, S.; Komatsu, H.; Sakai, T.; Kamiya, T.

2007-01-01

Using the proton induced gamma-ray emission (PIGE) method (TIARA, Japan), we have studied fluorine (F) distribution in the human tooth under various conditions. Here, we report F uptake into the human tooth from a thin layer of F-releasing low viscous resin (FLVR). Crowns of human teeth were horizontally cut and the dentin of the cut surface was first covered with four kinds of FLVR (FL-Bond, Reactmer Bond, Xeno Bond, and Protect Liner F; thickness, 50-150 μm) according to the manufacturers' instructions. Non-F-releasing and F-releasing filling resins were also hardened, on the cut surfaces of crowns covered with four kinds of FLVR thin layers. The type of the non-F-releasing filling materials used was LITE FIL IIP: G1-A (FL-Bond and LITE FIL IIP), G2-A (Reactmer Bond and LITE FIL IIP), G3-A (Xeno Bond and LITE FIL IIP), and G4-A (Protect Liner F and LITE FIL IIP). The types of F-releasing filling materials used were G1-B (FL-Bond and Beautifil), G2-B (Reactmer Bond and Reactmer Paste), G3-B (Xeno Bond and Xeno CF Paste), and G4-B (Protect Liner F and Teethmate F-1). Treatment and measurements of specimens were the same as previously reported [H. Yamamoto, M. Nomahci, K. Yasuda, Y. Iwami, S. Ebisu, N. Yamamoto, T. Sakai, T. Kamiya, Nucl. Instr. and Meth. B 210 (2003) 388]. F uptake from specimens following one month of application was estimated from 2-D maps. F penetration was observed in all teeth of G1-A-G4-A groups. The maximum values of F concentration in each tooth and F penetration depth were larger for larger F concentrations in FLVR. FLVR was useful for the F uptake into the tooth, and the F distribution near the thin layer of FLVR depended on the materials used. Between G1-A and G1-B or G4-A and G4-B, the F uptake was significantly different. We were able to obtain fundamental data, which were useful for the analysis of F transportation relating to prevention of caries

Fluorine uptake into the human tooth from a thin layer of F-releasing material

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, H. [Department of Restorative Dentistry and Endodontology, Graduate School of Dentistry, Osaka University, 1-8 Yamadaoka, Suita, Osaka, 565-0871 (Japan)]. E-mail: yhiroko@dent.osaka-u.ac.jp; Nomachi, M. [Graduate School of Science, Osaka University, Toyonaka, Osaka, 560-0043 (Japan); Yasuda, K. [Wakasa Wan Energy Research Center, Tsuruga, Fukui, 914-0192 (Japan); Iwami, Y. [Department of Restorative Dentistry and Endodontology, Graduate School of Dentistry, Osaka University, 1-8 Yamadaoka, Suita, Osaka, 565-0871 (Japan); Ebisu, S. [Department of Restorative Dentistry and Endodontology, Graduate School of Dentistry, Osaka University, 1-8 Yamadaoka, Suita, Osaka, 565-0871 (Japan); Komatsu, H. [Graduate School of Dental Medicine, Hokkaido University, Sapporo, Hokkaido, 060-8585 (Japan); Sakai, T. [Advanced Radiation Technology Center, JAERI, Takasaki, Gunma, 370-1292 (Japan); Kamiya, T. [Advanced Radiation Technology Center, JAERI, Takasaki, Gunma, 370-1292 (Japan)

2007-07-15

Using the proton induced gamma-ray emission (PIGE) method (TIARA, Japan), we have studied fluorine (F) distribution in the human tooth under various conditions. Here, we report F uptake into the human tooth from a thin layer of F-releasing low viscous resin (FLVR). Crowns of human teeth were horizontally cut and the dentin of the cut surface was first covered with four kinds of FLVR (FL-Bond, Reactmer Bond, Xeno Bond, and Protect Liner F; thickness, 50-150 {mu}m) according to the manufacturers' instructions. Non-F-releasing and F-releasing filling resins were also hardened, on the cut surfaces of crowns covered with four kinds of FLVR thin layers. The type of the non-F-releasing filling materials used was LITE FIL IIP: G1-A (FL-Bond and LITE FIL IIP), G2-A (Reactmer Bond and LITE FIL IIP), G3-A (Xeno Bond and LITE FIL IIP), and G4-A (Protect Liner F and LITE FIL IIP). The types of F-releasing filling materials used were G1-B (FL-Bond and Beautifil), G2-B (Reactmer Bond and Reactmer Paste), G3-B (Xeno Bond and Xeno CF Paste), and G4-B (Protect Liner F and Teethmate F-1). Treatment and measurements of specimens were the same as previously reported [H. Yamamoto, M. Nomahci, K. Yasuda, Y. Iwami, S. Ebisu, N. Yamamoto, T. Sakai, T. Kamiya, Nucl. Instr. and Meth. B 210 (2003) 388]. F uptake from specimens following one month of application was estimated from 2-D maps. F penetration was observed in all teeth of G1-A-G4-A groups. The maximum values of F concentration in each tooth and F penetration depth were larger for larger F concentrations in FLVR. FLVR was useful for the F uptake into the tooth, and the F distribution near the thin layer of FLVR depended on the materials used. Between G1-A and G1-B or G4-A and G4-B, the F uptake was significantly different. We were able to obtain fundamental data, which were useful for the analysis of F transportation relating to prevention of caries.

Stochastic Modeling of Radioactive Material Releases

International Nuclear Information System (INIS)

Andrus, Jason; Pope, Chad

2015-01-01

Nonreactor nuclear facilities operated under the approval authority of the U.S. Department of Energy use unmitigated hazard evaluations to determine if potential radiological doses associated with design basis events challenge or exceed dose evaluation guidelines. Unmitigated design basis events that sufficiently challenge dose evaluation guidelines or exceed the guidelines for members of the public or workers, merit selection of safety structures, systems, or components or other controls to prevent or mitigate the hazard. Idaho State University, in collaboration with Idaho National Laboratory, has developed a portable and simple to use software application called SODA (Stochastic Objective Decision-Aide) that stochastically calculates the radiation dose associated with hypothetical radiological material release scenarios. Rather than producing a point estimate of the dose, SODA produces a dose distribution result to allow a deeper understanding of the dose potential. SODA allows users to select the distribution type and parameter values for all of the input variables used to perform the dose calculation. SODA then randomly samples each distribution input variable and calculates the overall resulting dose distribution. In cases where an input variable distribution is unknown, a traditional single point value can be used. SODA was developed using the MATLAB coding framework. The software application has a graphical user input. SODA can be installed on both Windows and Mac computers and does not require MATLAB to function. SODA provides improved risk understanding leading to better informed decision making associated with establishing nuclear facility material-at-risk limits and safety structure, system, or component selection. It is important to note that SODA does not replace or compete with codes such as MACCS or RSAC, rather it is viewed as an easy to use supplemental tool to help improve risk understanding and support better informed decisions. The work was

Stochastic Modeling of Radioactive Material Releases

Energy Technology Data Exchange (ETDEWEB)

Andrus, Jason [Idaho National Lab. (INL), Idaho Falls, ID (United States); Pope, Chad [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-09-01

Nonreactor nuclear facilities operated under the approval authority of the U.S. Department of Energy use unmitigated hazard evaluations to determine if potential radiological doses associated with design basis events challenge or exceed dose evaluation guidelines. Unmitigated design basis events that sufficiently challenge dose evaluation guidelines or exceed the guidelines for members of the public or workers, merit selection of safety structures, systems, or components or other controls to prevent or mitigate the hazard. Idaho State University, in collaboration with Idaho National Laboratory, has developed a portable and simple to use software application called SODA (Stochastic Objective Decision-Aide) that stochastically calculates the radiation dose associated with hypothetical radiological material release scenarios. Rather than producing a point estimate of the dose, SODA produces a dose distribution result to allow a deeper understanding of the dose potential. SODA allows users to select the distribution type and parameter values for all of the input variables used to perform the dose calculation. SODA then randomly samples each distribution input variable and calculates the overall resulting dose distribution. In cases where an input variable distribution is unknown, a traditional single point value can be used. SODA was developed using the MATLAB coding framework. The software application has a graphical user input. SODA can be installed on both Windows and Mac computers and does not require MATLAB to function. SODA provides improved risk understanding leading to better informed decision making associated with establishing nuclear facility material-at-risk limits and safety structure, system, or component selection. It is important to note that SODA does not replace or compete with codes such as MACCS or RSAC, rather it is viewed as an easy to use supplemental tool to help improve risk understanding and support better informed decisions. The work was

Impact of pore characteristics of silica materials on loading capacity and release behavior of ibuprofen

Energy Technology Data Exchange (ETDEWEB)

Numpilai, Thanapha [Department of Chemical Engineering, Faculty of Engineering, Kasetsart University, Bangkok 10900 (Thailand); Muenmee, Suthaporn [Department of Chemical Engineering, Faculty of Engineering, Kasetsart University, Bangkok 10900 (Thailand); Center for Advanced Studies in Nanotechnology and Its Applications in Chemical Food and Agricultural Industries, Kasetsart University, Bangkok 10900 (Thailand); Witoon, Thongthai, E-mail: fengttwi@ku.ac.th [Department of Chemical Engineering, Faculty of Engineering, Kasetsart University, Bangkok 10900 (Thailand); Center for Advanced Studies in Nanotechnology and Its Applications in Chemical Food and Agricultural Industries, Kasetsart University, Bangkok 10900 (Thailand); NANOTEC-KU-Center of Excellence on Nanoscale Materials Design for Green Nanotechnology, Kasetsart University, Bangkok 10900 (Thailand)

2016-02-01

Impact of pore characteristics of porous silica supports on loading capacity and release behavior of ibuprofen was investigated. The porous silica materials and ibuprofen-loaded porous silica materials were thoroughly characterized by N{sub 2}-sorption, thermal gravimetric and derivative weight analyses (TG-DTW), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM), transmission electron microscope (TEM) to determine the physical properties of materials, amount of ibuprofen adsorbed and position of ibuprofen. The detailed characterization reveals that the ibuprofen molecules adsorbed inside the mesopores. Increasing the mesopore size from 5 nm to 10 nm increased the ibuprofen loading from 0.74 to 0.85 mmol/g, respectively. Incorporation of macropore into the structure of porous silica materials enhanced the ibuprofen loading capacity of 11.8–20.3%. The ibuprofen-loaded bimodal meso-macroporous silica materials exhibited the highest dissolution of 92 wt.% within an hour. The ibuprofen particles deposited on the external surface of the porous silica materials showed a lower dissolution rate than the ibuprofen adsorbed inside the mesopores due to the formation of ibuprofen crystalline. - Highlights: • Impacts of pore characteristics of supports on adsorption and release of ibuprofen • Increasing mesopore size increased the ibuprofen loading and dissolution rate. • Macropores reduced the diffusion pathway of ibuprofen and dissolution medium.

Impact of pore characteristics of silica materials on loading capacity and release behavior of ibuprofen

International Nuclear Information System (INIS)

Numpilai, Thanapha; Muenmee, Suthaporn; Witoon, Thongthai

2016-01-01

Impact of pore characteristics of porous silica supports on loading capacity and release behavior of ibuprofen was investigated. The porous silica materials and ibuprofen-loaded porous silica materials were thoroughly characterized by N 2 -sorption, thermal gravimetric and derivative weight analyses (TG-DTW), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM), transmission electron microscope (TEM) to determine the physical properties of materials, amount of ibuprofen adsorbed and position of ibuprofen. The detailed characterization reveals that the ibuprofen molecules adsorbed inside the mesopores. Increasing the mesopore size from 5 nm to 10 nm increased the ibuprofen loading from 0.74 to 0.85 mmol/g, respectively. Incorporation of macropore into the structure of porous silica materials enhanced the ibuprofen loading capacity of 11.8–20.3%. The ibuprofen-loaded bimodal meso-macroporous silica materials exhibited the highest dissolution of 92 wt.% within an hour. The ibuprofen particles deposited on the external surface of the porous silica materials showed a lower dissolution rate than the ibuprofen adsorbed inside the mesopores due to the formation of ibuprofen crystalline. - Highlights: • Impacts of pore characteristics of supports on adsorption and release of ibuprofen • Increasing mesopore size increased the ibuprofen loading and dissolution rate. • Macropores reduced the diffusion pathway of ibuprofen and dissolution medium.

ARAC: a centralized computer assisted emergency planning, response, and assessment system for atmospheric releases of toxic material

International Nuclear Information System (INIS)

Dickerson, M.H.; Knox, J.B.

1986-10-01

The Atmospheric Release Advisory Capability (ARAC) is an emergency planning, response, and assessment service, developed by the US Departments of Energy and Defense, and focused, thus far, on atmospheric releases of nuclear material. For the past 14 years ARAC has responded to over 150 accidents, potential accidents, and major exercises. The most notable accident responses are the COSMOS 954 reentry, the Three Mile Island (TMI-2) accident and subsequent purge of 85 Kr from the containment vessel, the recent UF 6 accident at the Kerr-McGee Plant, Gore, Oklahoma, and the Chernobyl nuclear reactor accident in the Soviet Union. Based on experience in the area of emergency response, developed during the past 14 years, this paper describes the cost effectiveness and other advantages of a centralized emergency planning, response, and assessment service for atmospheric releases of nuclear material

ARAC: a centralized computer-assisted emergency planning, response, and assessment system for atmospheric releases of toxic material

International Nuclear Information System (INIS)

Dickerson, M.H.; Knox, J.B.

1987-01-01

The Atmospheric Release Advisory Capability (ARAC) is an emergency planning, response, and assessment service, developed by the US Departments of Energy and Defense, and focused, thus far, on atmospheric releases of nuclear material. For the past 14 years ARAC has responded to over 150 accidents, potential accidents, and major exercises. The most notable accident responses are the COSMOS 954 reentry, the Three Mile Island (TMI-2) accident and subsequent purge of 85 Kr from the containment vessel, the recent UF 6 accident at the Kerr-McGee Plant, Gore, Oklahoma, and the Chernobyl nuclear reactor accident in the Soviet Union. Based on experience in the area of emergency response, developed during the past 14 years, this paper describes the cost effectiveness and other advantages of a centralized emergency planning, response, and assessment service for atmospheric releases of nuclear material

The Research and Application of Sustainable Long-release Carbon Material with Agricultural Waste

Science.gov (United States)

Wen, Z.

2017-12-01

(1) The element analysis shown that ten kinds of agricultural wastes containing a certain amount of C, N, H elements, the highest content of C element, and t value ranges from 36.02% 36.02%, and the variation of C, N, H elements content in difference materials was not significant. The TOC concentration of sugar cane was up to 38.66 mg·g-1, and quality ratio was 39‰, significantly lower than C elements content. The released TOC quality of the rest materials were 2.36 2.36 mg·g-1, and the order from high to low were the soybean straw, rice straw, corn straw, rice husk, poplar branches, wheat straw, reeds, corn cob and wood chips respectively. The long-term leaching experiment of selected Optimized agricultural waste showed that the TOC content in leaching solution rise rapidly to peak value and was stable afterwards, with the concentration of 4.59 19.46 mg·g-1. The TOC releasing amount order was same with the short-term leaching experiment. (2) The releasing of nitrate nitrogen in ten kinds of agricultural waste was low (corn straw was up to 0.12mg·g-1, and the rest were all below 0.04mg·g-1 without accumulation. Most of the ammonia nitrogen concentration in leachate was lower than 0.3mg·g-1. The kjeldahl nitrogen in the corn straw, soybean straw, rice straw, reed, rice husk, and sugar cane leachate (0.81 1.65mg·g-1) were higher than that of poplar branches, corn cob and wood chips (corn straw, rice husk and wheat straw leachate. Above all, it can be concluded that the sugar cane, corn straw, rice husk, wheat straw, corn cob, wood were ideal carbon source material in ten kinds of agricultural.

Possibilities for the Reuse of Steel from Decommissioning. Selected Scenarios in the Process of Proposal and Evaluation of Manufacturing Processes for Conditional Released Steel and their Application in General and Nuclear Industry

International Nuclear Information System (INIS)

Bezak, P.; Daniska, V.; Ondra, F.; Necas, V.

2012-01-01

Conditional release of steels from NPP decommissioning enables controlled reuse of non-negligible volumes of steels. For proposal of scenarios for steel reuse, it is needed to identify and evaluate partial elementary activities of the whole process from conditional release of steels, manufacturing of various elements up to realisation of scenarios. For scenarios of reuse of conditionally released steel the products of steel, as steel reinforcements, rails, profiles and sheets for technical constructions such as bridges, tunnels, railways and other constructions which guarantee the long-term properties over the periods of 50-100 years are considered. The idea offers also the possibility for using this type of steel for particular technical constructions, directly usable in nuclear facilities. The paper presents the review of activities for manufacturing of various steel construction elements made from conditionally released steels and their use in general and also in the nuclear industry. As the starting material for manufacturing of steel elements ingots or just fragments of steel after dismantling in controlled area can be used. These input materials are re-melted in industrial facilities in order to achieve the required physical and chemical characteristics. Mostly used technique for manufacturing of the steel construction elements is rolling. As the products considered in scenarios for reuse of conditional released steels are bars for reinforcement concrete, rolled steel sheets and other rolled profiles. For use in the nuclear industry it offers the possibility for casting of thick-walled steel containers for long-term storage of high level radioactive components in integral storage and also assembly of stainless steel tanks for storing of liquid radioactive waste. Lists of elementary activities which are needed for manufacturing of selected steel elements are elaborated. These elementary activities are then the base for detailed safety evaluation of external

A controlled release of ibuprofen by systematically tailoring the morphology of mesoporous silica materials

International Nuclear Information System (INIS)

Qu Fengyu; Zhu Guangshan; Lin Huiming; Zhang Weiwei; Sun Jinyu; Li Shougui; Qiu Shilun

2006-01-01

A series of mesoporous silica materials with similar pore sizes, different morphologies and variable pore geometries were prepared systematically. In order to control drug release, ibuprofen was employed as a model drug and the influence of morphology and pore geometry of mesoporous silica on drug release profiles was extensively studied. The mesoporous silica and drug-loaded samples were characterized by X-ray diffraction, Fourier transform IR spectroscopy, N 2 adsorption and desorption, scanning electron microscopy, and transmission electron microscopy. It was found that the drug-loading amount was directly correlated to the Brunauer-Emmett-Teller surface area, pore geometry, and pore volume; while the drug release profiles could be controlled by tailoring the morphologies of mesoporous silica carriers. - Graphical abstract: The release of ibuprofen is controlled by tailoring the morphologies of mesoporous silica. The mesoporous silica and drug-loaded samples are characterized by powder X-ray diffraction, Fourier transform IR spectroscopy, N 2 adsorption and desorption, scanning electron microscopy, and transmission electron microscopy. The drug-loading amount is directly correlated to the Brunauer-Emmett-Teller surface area, pore geometry, and pore volume; while the drug release profiles can be controlled by tailoring the morphologies of mesoporous silica carriers

Energy production from waste with regard to the possibilities of high-grade insulating granulates for building material through the distension method

Energy Technology Data Exchange (ETDEWEB)

Neumann, P

1981-01-01

A study is made of the extent to which energy contained in residual materials can be released and be used for making concretes, based on waste products from industry, domestic and communal refuse as well as filings from the coal mining industry, flotation and screening plants, and coal-pit power plants. Also examined is the organic composition of the residue for residual energy release. The studies indicate that significant energy savings can be obtained by the release of residual energy of original raw material in the making of concretes. 14 figures, 6 tables.

Bone substitute material composition and morphology differentially modulate calcium and phosphate release through osteoclast-like cells.

Science.gov (United States)

Konermann, A; Staubwasser, M; Dirk, C; Keilig, L; Bourauel, C; Götz, W; Jäger, A; Reichert, C

2014-04-01

The aim of this study was to determine the material composition and cell-mediated remodelling of different calcium phosphate-based bone substitutes. Osteoclasts were cultivated on bone substitutes (Cerabone, Maxresorb, and NanoBone) for up to 5 days. Bafilomycin A1 addition served as the control. To determine cellular activity, the supernatant content of calcium and phosphate was measured by inductively coupled plasma optical emission spectrometry. Cells were visualized on the materials by scanning electron microscopy. Material composition and surface characteristics were assessed by energy-dispersive X-ray spectroscopy. Osteoclast-induced calcium and phosphate release was material-specific. Maxresorb exhibited the highest ion release to the medium (P = 0.034; calcium 40.25mg/l day 5, phosphate 102.08 mg/l day 5) and NanoBone the lowest (P = 0.021; calcium 8.43 mg/l day 5, phosphate 15.15 mg/l day 5); Cerabone was intermediate (P = 0.034; calcium 16.34 mg/l day 5, phosphate 30.6 mg/l day 5). All investigated materials showed unique resorption behaviours. The presented methodology provides a new perspective on the investigation of bone substitute biodegradation, maintaining the material-specific micro- and macrostructure. Copyright © 2013 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Commutability of possible external quality assessment materials for cardiac troponin measurement.

Directory of Open Access Journals (Sweden)

Shunli Zhang

Full Text Available The measurement of cardiac troponin is crucial in the diagnosis of myocardial infarction. The performance of troponin measurement is most conveniently monitored by external quality assessment (EQA programs. The commutability of EQA samples is often unknown and the effectiveness of EQA programs is limited.Commutability of possible EQA materials was evaluated. Commercial control materials used in an EQA program, human serum pools prepared from patient samples, purified analyte preparations, swine sera from model animals and a set of patient samples were measured for cTnI with 4 assays including Abbott Architect, Beckman Access, Ortho Vitros and Siemens Centaur. The measurement results were logarithm-transformed, and the transformed data for patient samples were pairwise analyzed with Deming regression and 95% prediction intervals were calculated for each pair of assays. The commutability of the materials was evaluated by comparing the logarithmic results of the materials with the limits of the intervals. Matrix-related biases were estimated for noncommutable materials. The impact of matrix-related bias on EQA was analyzed and a possible correction for the bias was proposed.Human serum pools were commutable for all assays; purified analyte preparations were commutable for 2 of the 6 assay pairs; commercial control materials and swine sera were all noncommutable; swine sera showed no reactivity to Vitros assay. The matrix-related biases for noncommutable materials ranged from -83% to 944%. Matrix-related biases of the EQA materials caused major abnormal between-assay variations in the EQA program and correction of the biases normalized the variations.Commutability of materials has major impact on the effectiveness of EQA programs for cTnI measurement. Human serum pools prepared from patient samples are commutable and other materials are mostly noncommutable. EQA programs should include at least one human serum pool to allow proper interpretation of

Possibilities to improve the adaptation quality of calculated material substitutes

Energy Technology Data Exchange (ETDEWEB)

Geske, G.

1981-04-01

In calculating the composition of material substitutes by a system of simultaneous equations it is possible, by using a so called quality index, to find out of the set of solutions which generally exists that solution which possesses the best adaptation quality. Further improvement is often possible by describing coherent scattering and photoelectric interaction by an own material parameter for each effect. The exact formulation of these quantities as energy indepedent functions is, however, impossible. Using a set of attenuation coefficients at suitably chosen energies as coefficients for the system of equations the best substitutes are found. The solutions for the investigated example are identical with the original relative to its chemical composition. Such solutions may be of use in connection with neutrons, protons, heavy ions and negative pions. The components taken into consideration must, of course, permit such solutions. These facts are discussed in detail by two examples.

Comparing Titanium Release from Ceramic Tiles using a waste material characterization test - Influence of Calcium and Organic Matter concentrations

DEFF Research Database (Denmark)

Heggelund, Laura Roverskov; Hansen, Steffen Foss; Astrup, Thomas Fruergaard

2015-01-01

Nanomaterials are beneficial in the building industry to enhance or add certain features to commonly used materials. One example is the use of nano-titanium dioxide in the surface coating of ceramic tiles, to make the tiles surface self-cleaning. At the end of life stage, ceramic tiles might...... to assess if nano-titanium dioxide coated ceramic tiles are suitable for depositing in a landfill or not. Specifically, we used compliance batch test method, which is a simple test evaluating the release from a solid material to an aqueous media during 24 hrs. If nano-Ti particles are released from solid...... immediately after the 24 hrs. test using single particle ICPMS and Transmission Electron Microscopy imaging. The preliminary results suggest that nanoparticulate titanium is released from both tiles – with and without nano-titanium dioxide coating. The size distributions of the released particles are similar...

The cleanup of releases of radioactive materials from commercial low-level radioactive waste disposal sites: Whose jurisdiction?

International Nuclear Information System (INIS)

Hartnett, C.

1994-01-01

There exists an overlap between the Comprehensive Environmental Response, Compensation and Recovery Act (open-quotes CERCLAclose quotes) and the Atomic Energy Act (open-quotes AEAclose quotes) regarding the cleanup of releases of radioactive materials from commercial low-level radioactive waste sites. The Nuclear Regulatory Commission (open-quotes NRCclose quotes) and Agreement States have jurisdiction under the AEA, and the Environmental Protection Agency (open-quotes EPAclose quotes) has jurisdiction pursuant to CERCLA. This overlapping jurisdiction has the effect of imposing CERCLA liability on parties who have complied with AEA regulations. However, CERCLA was not intended to preempt existing legislation. This is evidenced by the federally permitted release exemption, which explicitly exempts releases from CERCLA liability pursuant to an AEA license. With little guidance as to the applicability of this exemption, it is uncertain whether CERCLA's liability is broad enough to supersede the Atomic Energy Act. It is the purpose of this paper to discuss the overlapping jurisdiction for the cleanup of releases of radioactive materials from commercial low-level radioactive waste disposal sites with particular emphasis on the cleanup at the Maxey Flats, West Valley and Sheffield sites

Regulatory Initiatives for Control and Release of Technologically Enhanced Naturally-Occurring Radioactive Material

International Nuclear Information System (INIS)

Egidi, P.V.

1999-01-01

Current drafts of proposed standards and suggested State regulations for control and release of technologically-enhanced naturally-occurring radioactive material (TENORM), and standards for release of volumetrically-contaminated material in the US are reviewed. These are compared to the recommendations of the International Atomic Energy Association (IAEA) Safety Series and the European Commission (EC) proposals. Past regulatory efforts with respect to TENORM in the US dealt primarily with oil-field related wastes. Currently, nine states (AK, GA, LA, MS, NM, OH, OR SC, TX) have specific regulations pertaining to TENORM, mostly based on uranium mill tailings cleanup criteria. The new US proposals are dose- or risk-based, as are the IAEA and EC recommendations, and are grounded in the linear no threshold hypothesis (LNT). TENORM wastes involve extremely large volumes, particularly scrap metal and mine wastes. Costs to control and dispose of these wastes can be considerable. The current debate over the validity of LNT at low doses and low dose rates is particularly germane to this discussion. Most standards setting organizations and regulatory agencies base their recommendations on the LNT. The US Environmental Protection Agency has released a draft Federal Guidance Report that recommends calculating health risks from low-level exposure to radionuclides based on the LNT. However, some scientific and professional organizations are openly questioning the validity of LNT and its basis for regulations, practices, and costs to society in general. It is not clear at this time how a non-linear regulatory scheme would be implemented

Regulatory Initiatives for Control and Release of Technologically Enhanced Naturally-Occurring Radioactive Materials

Energy Technology Data Exchange (ETDEWEB)

Egidi, P.V.

1999-03-02

Current drafts of proposed standards and suggested State regulations for control and release of technologically-enhanced naturally-occurring radioactive material (TENORM), and standards for release of volumetrically-contaminated material in the US are reviewed. These are compared to the recommendations of the International Atomic Energy Association (IAEA) Safety Series and the European Commission (EC) proposals. Past regulatory efforts with respect to TENORM in the US dealt primarily with oil-field related wastes. Currently, nine states (AK, GA, LA, MS, NM, OH, OR SC, TX) have specific regulations pertaining to TENORM, mostly based on uranium mill tailings cleanup criteria. The new US proposals are dose- or risk-based, as are the IAEA and EC recommendations, and are grounded in the linear no threshold hypothesis (LNT). TENORM wastes involve extremely large volumes, particularly scrap metal and mine wastes. Costs to control and dispose of these wastes can be considerable. The current debate over the validity of LNT at low doses and low dose rates is particularly germane to this discussion. Most standards setting organizations and regulatory agencies base their recommendations on the LNT. The US Environmental Protection Agency has released a draft Federal Guidance Report that recommends calculating health risks from low-level exposure to radionuclides based on the LNT. However, some scientific and professional organizations are openly questioning the validity of LNT and its basis for regulations, practices, and costs to society in general. It is not clear at this time how a non-linear regulatory scheme would be implemented.

Chitosan/alginate based multilayers to control drug release from ophthalmic lens.

Science.gov (United States)

Silva, Diana; Pinto, Luís F V; Bozukova, Dimitriya; Santos, Luís F; Serro, Ana Paula; Saramago, Benilde

2016-11-01

In this study we investigated the possibility of using layer-by-layer deposition, based in natural polymers (chitosan and alginate), to control the release of different ophthalmic drugs from three types of lens materials: a silicone-based hydrogel recently proposed by our group as drug releasing soft contact lens (SCL) material and two commercially available materials: CI26Y for intraocular lens (IOLs) and Definitive 50 for SCLs. The optimised coating, consisting in one double layer of (alginate - CaCl2)/(chitosan+glyoxal) topped with a final alginate-CaCl2 layer to avoid chitosan degradation by tear fluid proteins, proved to have excellent features to control the release of the anti-inflammatory, diclofenac, while keeping or improving the physical properties of the lenses. The coating leads to a controlled release of diclofenac from SCL and IOL materials for, at least, one week. Due to its high hydrophilicity (water contact angle≈0) and biocompatibility, it should avoid the use of further surface treatments to enhance the useŕs comfort. However, the barrier effect of this coating is specific for diclofenac, giving evidence to the need of optimizing the chemical composition of the layers in view of the desired drug. Copyright © 2016 Elsevier B.V. All rights reserved.

Antimicrobial beeswax coated polylactide films with silver control release capacity.

Science.gov (United States)

Martínez-Abad, Antonio; Lagarón, Jose Maria; Ocio, María Jose

2014-03-17

Although the application of silver based antimicrobial systems is a widespread technology, its implementation in areas such as food packaging is still challenging. The present paper describes the fabrication of poly(lactic acid) (PLA) coated with beeswax with controlled release properties for sustained antimicrobial performance. Release of silver ions from the polymers was monitored voltammetrically under various conditions (surface contact, immersion in various liquid media and at different pH values) throughout at least 7days. A higher release was noted with decreasing pH while surface release was much slower than the release when immersed in liquid medium. While uncoated films demonstrated a high burst release which in some instances implied surpassing some current migration restrictions (food), the addition of a beeswax layer allowed a sustained release of the antimicrobial compound. Increasing the thickness of the beeswax layer resulted in an increase in the water barrier properties of the films while reducing the relatively constant values of sustained release. Antimicrobial performance was correlated with the release of silver ions, indicating threshold concentrations for biocide action of films displayed a strong bactericidal effect against Salmonella enterica. The application of this functional barrier thus offers the possibility of tuning the release profiles of the films to suit a specific application and puts forth the possible suitability of these materials for food packaging or other migration sensitive applications. Copyright © 2013 Elsevier B.V. All rights reserved.

Implementation of decommissioning materials conditional clearance process to the OMEGA calculation code

International Nuclear Information System (INIS)

Zachar, Matej; Necas, Vladimir; Daniska, Vladimir

2011-01-01

The activities performed during nuclear installation decommissioning process inevitably lead to the production of large amount of radioactive material to be managed. Significant part of materials has such low radioactivity level that allows them to be released to the environment without any restriction for further use. On the other hand, for materials with radioactivity slightly above the defined unconditional clearance level, there is a possibility to release them conditionally for a specific purpose in accordance with developed scenario assuring that radiation exposure limits for population not to be exceeded. The procedure of managing such decommissioning materials, mentioned above, could lead to recycling and reuse of more solid materials and to save the radioactive waste repository volume. In the paper an a implementation of the process of conditional release to the OMEGA Code is analyzed in details; the Code is used for calculation of decommissioning parameters. The analytical approach in the material parameters assessment, firstly, assumes a definition of radiological limit conditions, based on the evaluation of possible scenarios for conditionally released materials, and their application to appropriate sorter type in existing material and radioactivity flow system. Other calculation procedures with relevant technological or economical parameters, mathematically describing e.g. final radiation monitoring or transport outside the locality, are applied to the OMEGA Code in the next step. Together with limits, new procedures creating independent material stream allow evaluation of conditional material release process during decommissioning. Model calculations evaluating various scenarios with different input parameters and considering conditional release of materials to the environment are performed to verify the implemented methodology. Output parameters and results of the model assessment are presented, discussed and conduced in the final part of the paper

Probabilistic Approach to Conditional Probability of Release of Hazardous Materials from Railroad Tank Cars during Accidents

Science.gov (United States)

2009-10-13

This paper describes a probabilistic approach to estimate the conditional probability of release of hazardous materials from railroad tank cars during train accidents. Monte Carlo methods are used in developing a probabilistic model to simulate head ...

The Temperature Condition of the Plate with Temperature-Dependent Thermal Conductivity and Energy Release

Directory of Open Access Journals (Sweden)

V. S. Zarubin

2016-01-01

Full Text Available The temperature state of a solid body, in addition to the conditions of its heat exchange with the environment, can greatly depend on the heat release (or heat absorption processes within the body volume. Among the possible causes of these processes should be noted such as a power release in the fuel elements of nuclear reactors, exothermic or endothermic chemical reactions in the solid body material, which respectively involve heat release or absorbtion, heat transfer of a part of the electric power in the current-carrying conductors (so-called Joule’s heat or the energy radiation penetrating into the body of a semitransparent material, etc. The volume power release characterizes an intensity of these processes.The extensive list of references to the theory of heat conductivity of solids offers solutions to problems to determine a stationary (steady over time and non-stationary temperature state of the solids (as a rule, of the canonical form, which act as the sources of volume power release. Thus, in general case, a possibility for changing power release according to the body volume and in solving the nonstationary problems also a possible dependence of this value on the time are taken into consideration.However, in real conditions the volume power release often also depends on the local temperature, and such dependence can be nonlinear. For example, with chemical reactions the intensity of heat release or absorption is in proportion to their rate, which, in turn, is sensitive to the temperature value, and a dependence on the temperature is exponential. A further factor that in such cases makes the analysis of the solid temperature state complicated, is dependence on the temperature and the thermal conductivity of this body material, especially when temperature distribution therein  is significantly non-uniform. Taking into account the influence of these factors requires the mathematical modeling methods, which allow us to build an adequate

Optically-controlled long-term storage and release of thermal energy in phase-change materials.

Science.gov (United States)

Han, Grace G D; Li, Huashan; Grossman, Jeffrey C

2017-11-13

Thermal energy storage offers enormous potential for a wide range of energy technologies. Phase-change materials offer state-of-the-art thermal storage due to high latent heat. However, spontaneous heat loss from thermally charged phase-change materials to cooler surroundings occurs due to the absence of a significant energy barrier for the liquid-solid transition. This prevents control over the thermal storage, and developing effective methods to address this problem has remained an elusive goal. Herein, we report a combination of photo-switching dopants and organic phase-change materials as a way to introduce an activation energy barrier for phase-change materials solidification and to conserve thermal energy in the materials, allowing them to be triggered optically to release their stored latent heat. This approach enables the retention of thermal energy (about 200 J g -1 ) in the materials for at least 10 h at temperatures lower than the original crystallization point, unlocking opportunities for portable thermal energy storage systems.

Redox buffered hydrofluoric acid etchant for the reduction of galvanic attack during release etching of MEMS devices having noble material films

Science.gov (United States)

Hankins, Matthew G [Albuquerque, NM

2009-10-06

Etchant solutions comprising a redox buffer can be used during the release etch step to reduce damage to the structural layers of a MEMS device that has noble material films. A preferred redox buffer comprises a soluble thiophosphoric acid, ester, or salt that maintains the electrochemical potential of the etchant solution at a level that prevents oxidation of the structural material. Therefore, the redox buffer preferentially oxidizes in place of the structural material. The sacrificial redox buffer thereby protects the exposed structural layers while permitting the dissolution of sacrificial oxide layers during the release etch.

Investigation of the possibilities for application of NORM into polymer materials

OpenAIRE

Srebrenkoska, Vineta

2016-01-01

The main aim of the proposed STSM project is to perform: • Comparison of fly ash characteristics (chemical composition, granulometry and density) from different origins: Slovenia and Macedonia. • Characterization of the polymer materials: thermoset and thermoplastic. • Estimate the possibilities for preparing of the composites based on fly ash as NORM material from different origins and polymers. The analyses of the inorganic fillers and organic polymer matrices will be made in or...

Tritium transport and release from lithium ceramic breeder materials

International Nuclear Information System (INIS)

Johnson, C.E.; Kopasz, J.P.; Tam, S.W.

1994-01-01

In an operating fusion reactor,, the tritium breeding blanket will reach a condition in which the tritium release rate equals the production rate. The tritium release rate must be fast enough that the tritium inventory in the blanket does not become excessive. Slow tritium release will result in a large tritium inventory, which is unacceptable from both economic and safety viewpoints As a consequence, considerable effort has been devoted to understanding the tritium release mechanism from ceramic breeders and beryllium neutron multipliers through theoretical, laboratory, and in-reactor studies. This information is being applied to the development of models for predicting tritium release for various blanket operating conditions

Principles for establishing limits for the release of radioactive materials into the environment

International Nuclear Information System (INIS)

1978-01-01

The document provides a basic consideration of concepts and principles for use by national authorities in setting limits for planned releases of radioactive material. The following topics are discussed general concepts, assessment of dose to the critical group, assessment of collective dose commitments, application of optimization techniques to the determination of discharge limits, explanation and application of the concept of collective dose commitment, discharge limitations based on concentration indices

Stored energy in fusion magnet materials irradiated at low temperatures

International Nuclear Information System (INIS)

Chaplin, R.L.; Kerchner, H.R.; Klabunde, C.E.; Coltman, R.R.

1989-08-01

During the power cycle of a fusion reactor, the radiation reaching the superconducting magnet system will produce an accumulation of immobile defects in the magnet materials. During a subsequent warm-up cycle of the magnet system, the defects will become mobile and interact to produce new defect configurations as well as some mutual defect annihilations which generate heat-the release of stored energy. This report presents a brief qualitative discussion of the mechanisms for the production and release of stored energy in irradiated materials, a theoretical analysis of the thermal response of irradiated materials, theoretical analysis of the thermal response of irradiated materials during warm-up, and a discussion of the possible impact of stored energy release on fusion magnet operation 20 refs

Optimum permeability for a cement based backfill material

International Nuclear Information System (INIS)

Jacobs, F.; Wittmann, F.H.; Iriya, K.

1989-01-01

In Switzerland it is planned to dispose low- and intermediate radioactive waste (LLW/ILW) in an underground repository. Between the materials present in a repository different chemical reactions may occur. Due to radiolytic decomposition, microbiological degradation and corrosion gas (mainly hydrogen) may be produced. The release of gas can cause the build-up of pressure in the cavern and finally lead to the formation of cracks and/or serious damage in the concrete structure or host rock. Through cracks a contamination of the groundwater and the biosphere could be possible. This investigation develops a suitable cement based material which can be used as backfill for the repository. Besides other aspects mentioned later a suitable backfill material has to be characterized by a certain minimum gas permeability and a as low as possible hydraulic conductivity. On the one hand gas permeability is necessary to release gas overpressure and on the other hand a low hydraulic conductivity should prevent leaching of backfill materials and contamination of the environment

Controlled-release tablet formulation of isoniazid.

Science.gov (United States)

Jain, N K; Kulkarni, K; Talwar, N

1992-04-01

Guar (GG) and Karaya gums (KG) alone and in combination with hydroxy-propylmethylcellulose (HPMC) were evaluated as release retarding materials to formulate a controlled-release tablet dosage form of isoniazid (1). In vitro release of 1 from tablets followed non-Fickian release profile with rapid initial release. Urinary excretion studies in normal subjects showed steady-state levels of 1 for 13 h. In vitro and in vivo data correlated (r = 0.9794). The studies suggested the potentiality of GG and KG as release retarding materials in formulating controlled-release tablet dosage forms of 1.

Accidental hazardous material releases with human impacts in the United States: exploration of geographical distribution and temporal trends.

Science.gov (United States)

Sengul, Hatice; Santella, Nicholas; Steinberg, Laura J; Chermak, Christina

2010-09-01

To investigate the circumstances and geographic and temporal distributions of hazardous material releases and resulting human impacts in the United States. Releases with fatalities, injuries, and evacuations were identified from reports to the National Response Center between 1990 and 2008, correcting for data quality issues identified in previous studies. From more than 550,000 reports, 861 deaths, 16,348 injuries and 741,427 evacuations were identified. Injuries from releases of chemicals at fixed facilities and natural gas from pipelines have decreased whereas evacuations from petroleum releases at fixed facilities have increased. Results confirm recent advances in chemical and pipeline safety and suggest directions for further improvement including targeted training and inspections and adoption of inherently safer design principles.

Release-ability of nano fillers from different nanomaterials (toward the acceptability of nanoproduct)

International Nuclear Information System (INIS)

Golanski, L.; Guiot, A.; Pras, M.; Malarde, M.; Tardif, F.

2012-01-01

It is of great interest to set up a reproducible and sensitive method able to qualify nanomaterials before their market introduction in terms of their constitutive nanoparticle release-ability in usage. Abrasion was performed on polycarbonate, epoxy, and PA11 polymers containing carbone nanotubes (CNT) up to 4 %wt. Using Taber linear standard tool and standard abrasion conditions no release from polymer coatings containing CNT was measured. In this study, new practical tools inducing non-standardized stresses able to compete with van der Waals forces were developed and tested on model polymers, showing controlled CNT dispersion. These stresses are still realistic, corresponding to scratching, instantaneous mechanical shocks, and abrasion of the surface. They offer an efficient way to quantify if release is possible from nanomaterials under different mechanical stresses and therefore give an idea about the mechanisms that favors it. Release under mechanical shocks and hard abrasion was obtained using these tools but only when nanomaterials present a bad dispersion of CNT within the epoxy matrix. Under the same conditions no release was obtained from the same material presenting a good dispersion. The CNT used in this study showed an external diameter Dext = 12 nm, an internal diameter Din = 5 nm, and a mean length of 1 μm. Release from paints under hard abrasion using a standard rotative Taber tool was obtained from a intentionaly non-optimized paint containing SiO 2 nanoparticles up to 35 %wt. The primary diameter of the SiO 2 was estimated to be around 12 nm. A metallic rake was efficient to remove nanoparticles from a non-woven fabric nanomaterial.

[The release of biologically active compounds from peat peloids].

Science.gov (United States)

Babaskin, D V

2011-01-01

This work had the objective to study kinetics of the release of flavonoides from peat peloid compositions containing extracts of medicinal herbs in model systems.The key parameters of the process are defined. The rate of liberation of flavonoides is shown to depend on their initial concentration in the compositions being used. The influence of the flavonoide composition of the tested extracts and dimethylsulfoxide on the release of biologically active compounds contained in the starting material in the model environment is estimated. The possibility of the layer-by-layer deposition of the compositions and peat peloids in order to increase the efficacy of flavonoide release from the starting composition and to ensure more rational utilization of the extracts of medicinal plants is demonstrated.

Chemical form of tritium released from solid breeder materials and the influences of it on a bred tritium recovery systems

International Nuclear Information System (INIS)

Furukubo, Y.; Nishikawa, M.; Nishida, Y.; Kinjyo, T.; Tanifuji, Takaaki; Kawamura, Yoshinori; Enoeda, Mikio

2004-01-01

The ratio of HTO in total tritium was measured at release of the bred tritium to the purge gas with hydrogen using the thermal release after irradiation method, where neutron irradiation was performed at JRR-3 reactor in JAERI or KUR reactor in Kyoto University. It is experimentally confirmed in this study that not a small portion of bred tritium is released to the purge gas in the form of HTO form ceramic breeder materials even when hydrogen is added to the purge gas. The chemical composition is to be decided by the competitive reaction at the grain surface of a ceramic breeder material where desorption reaction, isotope exchange reaction 1, isotope exchange reaction 2 and water formation reaction are considered to take part. Observation in this study implies that it is necessary to have a bred tritium recovery system applicable for both HT and HTO form to recover whole bred tritium. The chemical composition also decides the amount of tritium transferable to the cooling water of the electricity generation system through the structural material in the blanket system. Permeation behavior of tritium through some structural materials at various conditions are also discussed. (author)

Martian gullies: possible formation mechanism by dry granular material..

Science.gov (United States)

Cedillo-Flores, Y.; Durand-Manterola, H. J.

section Some of the geomorphological features in Mars are the gullies Some theories developed tried explain its origin either by liquid water liquid carbon dioxide or flows of dry granular material We made a comparative analysis of the Martian gullies with the terrestrial ones We propose that the mechanism of formation of the gullies is as follows In winter CO 2 snow mixed with sand falls in the terrain In spring the CO 2 snow sublimate and gaseous CO 2 make fluid the sand which flows like liquid eroding the terrain and forming the gullies By experimental work with dry granular material we simulated the development of the Martian gullies injecting air in the granular material section We present the characteristics of some terrestrial gullies forms at cold environment sited at Nevado de Toluca Volcano near Toluca City M e xico We compare them with Martian gullies choose from four different areas to target goal recognize or to distinguish to identify possible processes evolved in its formation Also we measured the lengths of those Martian gullies and the range was from 24 m to 1775 meters Finally we present results of our experimental work at laboratory with dry granular material

Calculation of releases of radioactive materials in gaseous and liquid effluents from boiling water reactors (BWR-GALE Code)

International Nuclear Information System (INIS)

Bangart, R.L.; Bell, L.G.; Boegli, J.S.; Burke, W.C.; Lee, J.Y.; Minns, J.L.; Stoddart, P.G.; Weller, R.A.; Collins, J.T.

1978-12-01

The calculational procedures described in the report reflect current NRC staff practice. The methods described will be used in the evaluation of applications for construction permits and operating licenses docketed after January 1, 1979, until this NUREG is revised as a result of additional staff review. The BWR-GALE (Boiling Water Reactor Gaseous and Liquid Effluents) Code is a computerized mathematical model for calculating the release of radioactive material in gaseous and liquid effluents from boiling water reactors (BWRs). The calculations are based on data generated from operating reactors, field tests, laboratory tests, and plant-specific design considerations incorporated to reduce the quantity of radioactive materials that may be released to the environment

Fluoride releasing and enamel demineralization around orthodontic brackets by fluoride-releasing composite containing nanoparticles.

Science.gov (United States)

Melo, Mary A S; Morais, Weslanny A; Passos, Vanara F; Lima, Juliana P M; Rodrigues, Lidiany K A

2014-05-01

Fluoride-containing materials have been suggested to control enamel demineralization around orthodontic brackets during the treatment with fixed appliances. The improvement of their properties has been made through innovations, such as the application of nanotechnology by incorporation of nanofillers. This in vitro study evaluated the capacity of fluoride releasing and enamel demineralization inhibition of fluoride-releasing nanofilled cement around orthodontic brackets using an artificial caries biofilm model. Forty bovine enamel discs were selected by evaluating surface microhardness and randomized into four groups (n = 10): non-fluoride-releasing microfilled composite, fluoride-releasing microfilled composite, resin-modified glass ionomer cement (RMGI), and fluoride-releasing nanofilled composite (FN). After brackets bonding in each disc, the specimens were subjected to a cariogenic challenge through a Streptococcus mutans biofilm model. After the experimental period, the biofilm formed around the brackets was collected for fluoride analysis and the mineral loss around the brackets was determined by integrated demineralization via cross-sectional microhardness measurement at 20 and 70 μm from the bracket margin. Additionally, samples of each group were subjected to energy-dispersive X-ray spectroscopy (EDX) analysis examined under a scanning electron microscopy (SEM). ANOVA followed by Tukey test were applied for fluoride concentration and mineral loss data, respectively. At both distances, only RMGI statistically differed from the other groups presenting the lowest demineralization, although there was a trend to a lower demineralization of enamel around brackets in FN group. Similar condition was found to fluoride concentration and EDX/SEM analysis. Under the cariogenic exposure condition of this study, the fluoride-releasing nanofilled material had similar performance to fluoride-releasing microfilled materials. The presence of nanofillers in the fluoride-releasing

Evaluation of gum mastic (Pistacia lentiscus as a microencapsulating and matrix forming material for sustained drug release

Directory of Open Access Journals (Sweden)

Dinesh M. Morkhade

2017-09-01

Full Text Available In this study, a natural gum mastic was evaluated as a microencapsulating and matrix-forming material for sustained drug release. Mastic was characterized for its physicochemical properties. Microparticles were prepared by oil-in-oil solvent evaporation method. Matrix tablets were prepared by wet and melt granulation techniques. Diclofenac sodium (DFS and diltiazem hydrochloride (DLTZ were used as model drugs. Mastic produced discrete and spherical microspheres with DLTZ and microcapsules with DFS. Particle size and drug loading of microparticles was in the range of 22–62 µm and 50–87%, respectively. Increase in mastic: drug ratio increased microparticle size, improved drug loading and decreased the drug release rate. Microparticles with gum: drug ratio of 2:1 could sustain DLTZ release up to 12 h and released 57% DFS in 12 h. Mastic produced tablets with acceptable pharmacotechnical properties. A 30% w/w of mastic in tablet could sustain DLTZ release for 5 h from wet granulation, and DFS release for 8 h and 11 h from wet and melt granulation, respectively. Results revealed that a natural gum mastic can be used successfully to formulate matrix tablets and microparticles for sustained drug release.

Controlled antiseptic release by alginate polymer films and beads.

Science.gov (United States)

Liakos, Ioannis; Rizzello, Loris; Bayer, Ilker S; Pompa, Pier Paolo; Cingolani, Roberto; Athanassiou, Athanassia

2013-01-30

Biodegradable polymeric materials based on blending aqueous dispersions of natural polymer sodium alginate (NaAlg) and povidone iodine (PVPI) complex, which allow controlled antiseptic release, are presented. The developed materials are either free standing NaAlg films or Ca(2+)-cross-linked alginate beads, which properly combined with PVPI demonstrate antibacterial and antifungal activity, suitable for therapeutic applications, such as wound dressing. Glycerol was used as the plasticizing agent. Film morphology was studied by optical and atomic force microscopy. It was found that PVPI complex forms well dispersed circular micro-domains within the NaAlg matrix. The beads were fabricated by drop-wise immersion of NaAlg/PVPI/glycerol solutions into aqueous calcium chloride solutions to form calcium alginate beads encapsulating PVPI solution (CaAlg/PVPI). Controlled release of PVPI was possible when the composite films and beads were brought into direct contact with water or with moist media. Bactericidal and fungicidal properties of the materials were tested against Escherichia coli bacteria and Candida albicans fungi. The results indicated very efficient antibacterial and antifungal activity within 48 h. Controlled release of PVPI into open wounds is highly desired in clinical applications to avoid toxic doses of iodine absorption by the wound. A wide variety of applications are envisioned such as external and internal wound dressings with controlled antiseptic release, hygienic and protective packaging films for medical devices, and polymer beads as water disinfectants. Copyright © 2012 Elsevier Ltd. All rights reserved.

Characterisation, in vitro release study, and antibacterial activity of montmorillonite-gentamicin complex material

International Nuclear Information System (INIS)

Rapacz-Kmita, A.; Bućko, M.M.; Stodolak-Zych, E.; Mikołajczyk, M.; Dudek, P.; nd Department of Surgery, Kopernika 21, 31-501 Krakow (Poland))" data-affiliation=" (Jagiellonian University, Medical College, 2nd Department of Surgery, Kopernika 21, 31-501 Krakow (Poland))" >Trybus, M.

2017-01-01

The present paper concerns the potential use of montmorillonite as a drug carrier and focusses on the intercalation of the studied clay with gentamicin (an aminoglycoside antibiotic) at various temperatures (20, 50 and 80 °C). The experiments were performed to identify the temperature required for the optimum intercalation of gentamicin into the interlayer of montmorillonite. The structural and microstructural properties of gentamicin and the potential for introducing it between smectite clay layers were investigated by means of X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopic techniques, and SEM with EDS analysis. Additionally, the in vitro drug release behaviour of the montmorillonite-gentamicin complex and its antibacterial activity against Escherichia coli (E. coli) bacteria was investigated. Based on these studies, the impact of temperature on the intercalation of the drug between layers of smectite was evaluated. It was found that an intercalation temperature of 50 °C resulted in the highest shift in the position of principle peak d (001) as measured by XRD, suggesting, that the greatest amount of gentamicin had been introduced into the interlayer space of montmorillonite at this temperature. Subsequently, the montmorillonite-gentamicin complex material obtained at 50 °C revealed the greatest capacity for killing E. coli bacteria during an in vitro test. - Highlights: • A novel montmorillonite-gentamicin hybrid materials was prepared as potential drug carrier. • Optimal conditions for the intercalation of gentamicin into the interlayer space of montmorillonite were tested. • The MMT-G complex material obtained at 50 °C revealed the greatest capacity for killing E. coli during the inhibitory zone test. • Modulating drug delivery was monitored and confirmed in in vitro drug release study.

Characterisation, in vitro release study, and antibacterial activity of montmorillonite-gentamicin complex material

Energy Technology Data Exchange (ETDEWEB)

Rapacz-Kmita, A., E-mail: kmita@agh.edu.pl [AGH University of Science and Technology, Faculty of Materials Science and Ceramics, Mickiewicza 30, 30-059 Krakow (Poland); Bućko, M.M.; Stodolak-Zych, E. [AGH University of Science and Technology, Faculty of Materials Science and Ceramics, Mickiewicza 30, 30-059 Krakow (Poland); Mikołajczyk, M. [The University Hospital in Krakow, Division of Microbiology, Kopernika 19, 31-501 Krakow (Poland); Dudek, P. [AGH University of Science and Technology, Faculty of Mechanical Engineering and Robotics, Mickiewicza 30, 30-059 Krakow (Poland); Trybus, M. [Jagiellonian University, Medical College, 2" n" d Department of Surgery, Kopernika 21, 31-501 Krakow (Poland)

2017-01-01

The present paper concerns the potential use of montmorillonite as a drug carrier and focusses on the intercalation of the studied clay with gentamicin (an aminoglycoside antibiotic) at various temperatures (20, 50 and 80 °C). The experiments were performed to identify the temperature required for the optimum intercalation of gentamicin into the interlayer of montmorillonite. The structural and microstructural properties of gentamicin and the potential for introducing it between smectite clay layers were investigated by means of X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopic techniques, and SEM with EDS analysis. Additionally, the in vitro drug release behaviour of the montmorillonite-gentamicin complex and its antibacterial activity against Escherichia coli (E. coli) bacteria was investigated. Based on these studies, the impact of temperature on the intercalation of the drug between layers of smectite was evaluated. It was found that an intercalation temperature of 50 °C resulted in the highest shift in the position of principle peak d{sub (001)} as measured by XRD, suggesting, that the greatest amount of gentamicin had been introduced into the interlayer space of montmorillonite at this temperature. Subsequently, the montmorillonite-gentamicin complex material obtained at 50 °C revealed the greatest capacity for killing E. coli bacteria during an in vitro test. - Highlights: • A novel montmorillonite-gentamicin hybrid materials was prepared as potential drug carrier. • Optimal conditions for the intercalation of gentamicin into the interlayer space of montmorillonite were tested. • The MMT-G complex material obtained at 50 °C revealed the greatest capacity for killing E. coli during the inhibitory zone test. • Modulating drug delivery was monitored and confirmed in in vitro drug release study.

Exploring the Nutrient Release Potential of Organic Materials as Integrated Soil Fertility Management Components Using SAFERNAC

NARCIS (Netherlands)

Maro, G.P.; Mrema, J.P.; Msanya, B.M.; Janssen, B.H.; Teri, J.M.

2014-01-01

The aim of this study was to establish the nutrient release potential of different organic materials and assess their role in integrated soil fertility management for coffee using the new coffee yield model SAFERNAC. It involved an incubation experiment conducted at TaCRI Lyamungu Screenhouse for

On the possibility of high-dispersed composite material obtaining in impulsive high-enthalpy flow

International Nuclear Information System (INIS)

Blinkov, I.V.; Brodyagin, A.G.; Ivanov, A.V.

1987-01-01

Thermodynamic possibility for the formation of TiC-Mo composite dispersed material in 1200-2800 K temperature interval and effect of H/Cl, C/Ti relation on the composite material composition are demonstrated. Investigation into the plasmo-chemical process of producing high-dispersed composite material in the pulsed regime has pointed out to a possibility of the product chemical composition regulation by changing the energy, flow-rate parameters and by conditions of component introduction into the plasmochemical reactor. Molybdenum-carbide composition powders produced are characterized by the particle size of ∼ 10 nm and high Mo and TiC distribution steadyness which allows one to exclude the stage of a long-term component mixing under the composition production

A method of surface area measurement of fuel materials by fission gas release at low temperature

International Nuclear Information System (INIS)

Kaimal, K.N.G.; Naik, M.C.; Paul, A.R.; Venkateswarlu, K.S.

1989-01-01

The present report deals with the development of a method for surface area measurement of nuclear fuel as well as fissile doped materials by fission gas release study at low temperature. The method is based on the evaluation of knock-out release rate of fission 133 Xe from irradiated fuel after sufficient cooling to decay the short lived activity. The report also describes the fabrication of an ampoule breaker unit for such study. Knock-out release rate of 133 Xe has been studied from UO 2 powders having varying surface area 'S' ranging from 270 cm 2 /gm to 4100 cm 2 /gm at two fissioning rates 10 12 f/cm 3 . sec. and 3.2x10 10 f/cm.sec. A relation between K and A has been established and discussed in this report. (author). 6 refs

Morphology of Gas Release in Physical Simulants

Energy Technology Data Exchange (ETDEWEB)

Daniel, Richard C.; Burns, Carolyn A.; Crawford, Amanda D.; Hylden, Laura R.; Bryan, Samuel A.; MacFarlan, Paul J.; Gauglitz, Phillip A.

2014-07-03

This report documents testing activities conducted as part of the Deep Sludge Gas Release Event Project (DSGREP). The testing described in this report focused on evaluating the potential retention and release mechanisms of hydrogen bubbles in underground radioactive waste storage tanks at Hanford. The goal of the testing was to evaluate the rate, extent, and morphology of gas release events in simulant materials. Previous, undocumented scoping tests have evidenced dramatically different gas release behavior from simulants with similar physical properties. Specifically, previous gas release tests have evaluated the extent of release of 30 Pa kaolin and 30 Pa bentonite clay slurries. While both materials are clays and both have equivalent material shear strength using a shear vane, it was found that upon stirring, gas was released immediately and completely from bentonite clay slurry while little if any gas was released from the kaolin slurry. The motivation for the current work is to replicate these tests in a controlled quality test environment and to evaluate the release behavior for another simulant used in DSGREP testing. Three simulant materials were evaluated: 1) a 30 Pa kaolin clay slurry, 2) a 30 Pa bentonite clay slurry, and 3) Rayleigh-Taylor (RT) Simulant (a simulant designed to support DSGREP RT instability testing. Entrained gas was generated in these simulant materials using two methods: 1) application of vacuum over about a 1-minute period to nucleate dissolved gas within the simulant and 2) addition of hydrogen peroxide to generate gas by peroxide decomposition in the simulants over about a 16-hour period. Bubble release was effected by vibrating the test material using an external vibrating table. When testing with hydrogen peroxide, gas release was also accomplished by stirring of the simulant.

RELEASE OF DRIED RADIOACTIVE WASTE MATERIALS TECHNICAL BASIS DOCUMENT

International Nuclear Information System (INIS)

KOZLOWSKI, S.D.

2007-01-01

This technical basis document was developed to support RPP-23429, Preliminary Documented Safety Analysis for the Demonstration Bulk Vitrification System (PDSA) and RPP-23479, Preliminary Documented Safety Analysis for the Contact-Handled Transuranic Mixed (CH-TRUM) Waste Facility. The main document describes the risk binning process and the technical basis for assigning risk bins to the representative accidents involving the release of dried radioactive waste materials from the Demonstration Bulk Vitrification System (DBVS) and to the associated represented hazardous conditions. Appendices D through F provide the technical basis for assigning risk bins to the representative dried waste release accident and associated represented hazardous conditions for the Contact-Handled Transuranic Mixed (CH-TRUM) Waste Packaging Unit (WPU). The risk binning process uses an evaluation of the frequency and consequence of a given representative accident or represented hazardous condition to determine the need for safety structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls. A representative accident or a represented hazardous condition is assigned to a risk bin based on the potential radiological and toxicological consequences to the public and the collocated worker. Note that the risk binning process is not applied to facility workers because credible hazardous conditions with the potential for significant facility worker consequences are considered for safety-significant SSCs and/or TSR-level controls regardless of their estimated frequency. The controls for protection of the facility workers are described in RPP-23429 and RPP-23479. Determination of the need for safety-class SSCs was performed in accordance with DOE-STD-3009-94, Preparation Guide for US. Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses, as described below

Influence of Citric Acid on the Metal Release of Stainless Steels

Energy Technology Data Exchange (ETDEWEB)

Mazinanian, N.; Wallinder, I. Odnevall; Hedberg, Y. S. [KTH Royal Institute of Technology, School of Chemical Science and Engineering, Department of Chemistry, Division of Surface and Corrosion Science, Stockholm (Sweden)

2015-08-15

Knowledge of how metal releases from the stainless steels used in food processing applications and cooking utensils is essential within the framework of human health risk assessment. A new European standard test protocol for testing metal release in food contact materials made from metals and alloys has recently been published by the Council of Europe. The major difference from earlier test protocols is the use of citric acid as the worst-case food simulant. The objectives of this study were to assess the effect of citric acid at acidic, neutral, and alkaline solution pH on the extent of metal release for stainless steel grades AISI 304 and 316, commonly used as food contact materials. Both grades released lower amounts of metals than the specific release limits when they were tested according to test guidelines. The released amounts of metals were assessed by means of graphite furnace atomic absorption spectroscopy, and changes in the outermost surface composition were determined using X-ray photoelectron spectroscopy. The results demonstrate that both the pH and the complexation capacity of the solutions affected the extent of metal release from stainless steel and are discussed from a mechanistic perspective. The outermost surface oxide was significantly enriched in chromium upon exposure to citric acid, indicating rapid passivation by the acid. This study elucidates the effect of several possible mechanisms, including complex ion- and ligand-induced metal release, that govern the process of metal release from stainless steel under passive conditions in solutions that contain citric acid.

The Investigation of Chlorates as a Possible Source of Oxygen and Chlorine Detected by the Sample Analysis at Mars (SAM) Instrument in Gale Crater, Mars

Science.gov (United States)

Sutter, B.; Archer, D. P.; Ming, D. W.; Niles, P. B.; Eigenbrode, J. L.; Franz, H.; Glavin, D. P.; McAdam, A. C.; Mahaffy, P; Stern, J. C.;

The Case for Extant Life on Mars and Its Possible Detection by the Viking Labeled Release Experiment.

Science.gov (United States)

Levin, Gilbert V; Straat, Patricia Ann

2016-10-01

The 1976 Viking Labeled Release (LR) experiment was positive for extant microbial life on the surface of Mars. Experiments on both Viking landers, 4000 miles apart, yielded similar, repeatable, positive responses. While the authors eventually concluded that the experiment detected martian life, this was and remains a highly controversial conclusion. Many believe that the martian environment is inimical to life and the LR responses were nonbiological, attributed to an as-yet-unidentified oxidant (or oxidants) in the martian soil. Unfortunately, no further metabolic experiments have been conducted on Mars. Instead, follow-on missions have sought to define the martian environment, mostly searching for signs of water. These missions have collected considerable data regarding Mars as a habitat, both past and present. The purpose of this article is to consider recent findings about martian water, methane, and organics that impact the case for extant life on Mars. Further, the biological explanation of the LR and recent nonbiological hypotheses are evaluated. It is concluded that extant life is a strong possibility, that abiotic interpretations of the LR data are not conclusive, and that, even setting our conclusion aside, biology should still be considered as an explanation for the LR experiment. Because of possible contamination of Mars by terrestrial microbes after Viking, we note that the LR data are the only data we will ever have on biologically pristine martian samples. Key Words: Extant life on Mars-Viking Labeled Release experiment-Astrobiology-Extraterrestrial life-Mars. Astrobiology 16, 798-810.

Irradiaiton facilities for testing solid and liquid blanket breeder materials with in-situ tritium release measurements in the HFR Petten

International Nuclear Information System (INIS)

Conrad, R.; Debarberis, L.

1991-01-01

Lithium-based tritium breeder materials for solid and liquid fusion reactor blanket concepts are being tested in the High Flux Reactor (HFR) Petten with in-situ tritium release measurements since 1985, within the European Fusion Technology Programme and the BEATRIX-I programme. Ceramic breeder materials are being tested in the EXOTIC and COMPLIMENT experimental programmes and the liquid breeder material, Pb-17Li, is being tested in the LIBRETTO experimental programme. The in-pile experiments are performed with irradiation facilities developed by the Joint Research Centre (JRC) Petten. The irradiation vehicles are multi-channel rigs. The sample holders consist of independent, fully instrumented and triple contained capsules. The out-of-pile experimental equipment consist of twelve independent circuits for on-line tritium release and tritium permeation measurements and eight independent circuits for temperature control. The experimental achievements obtained so far contribute to the selection of candidate tritium breeder materials for blanket concepts of near future machines like NET, ITER and DEMO. (orig.)

Comparison of the Heat Release Rate from the Mass Loss Calorimeter to the Cone Calorimeter for Wood-based Materials

Science.gov (United States)

Laura E. Hasburgh; Robert H. White; Mark A. Dietenberger; Charles R. Boardman

2015-01-01

There is a growing demand for material properties to be used as inputs in fi re behavior models designed to address building fire safety. This comparative study evaluates using the mass loss calorimeter as an alternative to the cone calorimeter for obtaining heat release rates of wood-based materials. For this study, a modified mass loss calorimeter utilized an...

RELEASE OF DRIED RADIOACTIVE WASTE MATERIALS TECHNICAL BASIS DOCUMENT

International Nuclear Information System (INIS)

KOZLOWSKI, D.S.

2005-01-01

The body of this document analyzes scenarios involving releases of dried tank waste from the DBVS dried waste transfer system and OGTS HEPA filters. Analyses of dried waste release scenarios from the CH-TRUM WPU are included as Appendix D

Technical committee meeting on evaluation of radioactive materials release and sodium fires in fast reactors

International Nuclear Information System (INIS)

1996-01-01

The objectives of the Technical Committee Meeting was to review the activities of research on radioactive materials release and sodium fires in fast reactors in each of the participating countries. It covered: out-of-pile experiments and analysis codes on source term; in-pile experiments on source term; core disruptive accidents; sodium leak experience in liquid metal fast reactors; evaluation of sodium fire; and aerosol behaviour

Technical committee meeting on evaluation of radioactive materials release and sodium fires in fast reactors

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

The objectives of the Technical Committee Meeting was to review the activities of research on radioactive materials release and sodium fires in fast reactors in each of the participating countries. It covered: out-of-pile experiments and analysis codes on source term; in-pile experiments on source term; core disruptive accidents; sodium leak experience in liquid metal fast reactors; evaluation of sodium fire; and aerosol behaviour.

Transformation of the released asbestos, carbon fibers and carbon nanotubes from composite materials and the changes of their potential health impacts.

Science.gov (United States)

Wang, Jing; Schlagenhauf, Lukas; Setyan, Ari

2017-02-20

Composite materials with fibrous reinforcement often provide superior mechanical, thermal, electrical and optical properties than the matrix. Asbestos, carbon fibers and carbon nanotubes (CNTs) have been widely used in composites with profound impacts not only on technology and economy but also on human health and environment. A large number of studies have been dedicated to the release of fibrous particles from composites. Here we focus on the transformation of the fibrous fillers after their release, especially the change of the properties essential for the health impacts. Asbestos fibers exist in a large number of products and the end-of-the-life treatment of asbestos-containing materials poses potential risks. Thermal treatment can transform asbestos to non-hazardous phase which provides opportunities of safe disposal of asbestos-containing materials by incineration, but challenges still exist. Carbon fibers with diameters in the range of 5-10 μm are not considered to be respirable, however, during the release process from composites, the carbon fibers may be split along the fiber axis, generating smaller and respirable fibers. CNTs may be exposed on the surface of the composites or released as free standing fibers, which have lengths shorter than the original ones. CNTs have high thermal stability and may be exposed after thermal treatment of the composites and still keep their structural integrity. Due to the transformation of the fibrous fillers during the release process, their toxicity may be significantly different from the virgin fibers, which should be taken into account in the risk assessment of fiber-containing composites.

Modulation of active pharmaceutical material release from a novel 'tablet in capsule system' containing an effervescent blend.

Science.gov (United States)

Gohel, Mukesh C; Sumitra G, Manhapra

2002-02-19

The objective of the present study was to obtain programmed drug delivery from hard gelatin capsules containing a hydrophilic plug (HPMC or guar gum). The significance of factors such as type of plug (powder or tablet), plug thickness and the formulation of fill material on the release pattern of diltiazem HCl, a model drug, was investigated. The body portion of the hard gelatin capsules was cross-linked by the combined effect of formaldehyde and heat treatment. A linear relationship was observed between weight of HPMC K15M and log % drug released at 4 h from the capsules containing the plug in powder form. In order to accelerate the drug release after a lag time of 4 h, addition of an effervescent blend, NaHCO(3) and citric acid, in the capsules was found to be essential. The plugs of HPMC in tablet form, with or without a water soluble adjuvant (NaCl or lactose) were used for obtaining immediate drug release after the lag time. Sodium chloride did not cause significant influence on drug release whereas lactose favourably affected the drug release. The capsules containing HPMC K15M tablet plug (200 mg) and 35 mg effervescent blend in body portion of the capsule met the selection criteria of less than 10% drug release in 4 h and immediate drug release thereafter. It is further shown that the drug release was also dependant on the type of swellable hydrophilic agent (HPMC or guar gum) and molecular weight of HPMC (K15M or 20 cPs). The results reveal that programmed drug delivery can be obtained from hard gelatin capsules by systemic formulation approach.

Free release measurement of radioactive waste on the basis of the Bayes theory

International Nuclear Information System (INIS)

Sokcic-Kostic, M.; Langer, F.; Schultheis, R.

2013-01-01

The application of Bayesian theory in the evaluation of the free release measurements requires complex co-ordination between experiment and analysis. The algorithms are more complex compared to those used in the frequentist data analysis and partly to those of the Monte Carlo methods. The user can get an objective treatment of parameters of the measurement error and - as a result - a reliable indication of confidence intervals. For release measurement, the upper limit of the confidence interval must be compared with the limit given by the Radiation Protection Regulations (StrlSchV) to decide on a possible release of the material under test. (orig.)

Modeling of molten core-concrete interactions and fission-product release

International Nuclear Information System (INIS)

Norkus, J.K.; Corradini, M.L.

1991-09-01

The study of molten core-concrete interaction is important in estimating the possible consequences of a severe nuclear reactor accident. CORCON-Mod2 is a computer program which models the thermal, chemical, and physical phenomena associated with molten core-concrete interactions. Models have been added to extend and improve the modeling of these phenomena. An ideal solution chemical equilibrium methodology is presented to predict the fission-product vaporization release. Additional chemical species have been added, and the calculation of chemical equilibrium has been expanded to the oxidic layer and to the mixed layer configuration. Recent experiments performed at Argonne National Laboratory are compared to CORCON predictions of melt temperature, erosion depth, and release fraction of fission products. The results consistently underpredicted the melt temperatures and erosion rates. However, the predictions of release of Te, Ba, Sr, and U were good. A sensitivity study of the effects of initial temperature, concrete type, use of the mixing option, degree of zirconium oxidation, cavity size, and amount of control material on erosion, gas production, and release of radioactive materials was performed for a PWR and a BWR. The initial melt temperature had the greatest effect on the results of interest. Concrete type and cavity size also had important effects. 78 refs., 35 figs., 40 tabs

Sorption/Desorption Behavior and Mechanism of NH4(+) by Biochar as a Nitrogen Fertilizer Sustained-Release Material.

Science.gov (United States)

Cai, Yanxue; Qi, Hejinyan; Liu, Yujia; He, Xiaowei

2016-06-22

Biochar, the pyrolysis product of biomass material with limited oxygen, has the potential to increase crop production and sustained-release fertilizer, but the understanding of the reason for improving soil fertility is insufficient, especially the behavior and mechanism of ammonium sulfate. In this study, the sorption/desorption effect of NH4(+) by biochar deriving from common agricultural wastes under different preparation temperatures from 200 to 500 °C was studied and its mechanism was discussed. The results showed that biochar displayed excellent retention ability in holding NH4(+) above 90% after 21 days under 200 °C preparation temperature, and it can be deduced that the oxygen functional groups, such as carboxyl and keto group, played the primary role in adsorbing NH4(+) due to hydrogen bonding and electrostatic interaction. The sorption/desorption effect and mechanism were studied for providing an optional way to dispose of agricultural residues into biochar as a nitrogen fertilizer sustained-release material under suitable preparation temperature.

Protocol for development of authorized release limits for concrete at U.S. Department of Energy sites

International Nuclear Information System (INIS)

Arnish, J.; Kamboj, S.; Chen, S.-Y.; Parker, F. L.; Smith, A. M.; Meservey, R. H.; Tripp, J. L.

2000-01-01

The purpose of this protocol is to assist US Department of Energy (DOE) sites in releasing concrete for reuse. Current regulations allow the sites to release surface-contaminated materials if their radioactivity falls below certain levels and to possibly release materials with volumetric contamination or higher levels of surface contamination on a case-by-case basis. In all cases, an ALARA (as low as reasonably achievable) analysis that evaluates the risks of releasing volumetrically contaminated concrete or concrete with higher levels of surface contamination is required as a basis for proposing and setting new release limits that allow for reuse of the concrete material. To evaluate the dose impacts of reusing radioactively contaminated material, the measured radiation levels (pCi/g or disintegrations per minute [dpm]/100 cm 2 ) must be converted to the estimated dose (mrem/yr) that would be received by affected individuals. The dose depends on the amounts and types of isotopes present and the time, distance, and method of exposure (e.g., inhalation or external exposure). For each disposition alternative, the protocol provides a systematic method to evaluate the impact of the dose on the affected individuals. The cost impacts of reusing concrete also need to be evaluated. They too depend on the disposition alternative and the extent and type of contamination. The protocol provides a method to perform a detailed analysis of these factors and evaluate the dose and cost impacts for various disposition alternatives. Once the dose and cost impacts of the various alternatives have been estimated, the protocol outlines the steps required to propose new release standards that allow release and reuse of the concrete material

Thermophilic methanogenic Archaea in compost material: occurrence, persistence and possible mechanisms for their distribution to other environments.

Science.gov (United States)

Thummes, Kathrin; Schäfer, Jenny; Kämpfer, Peter; Jäckel, Udo

2007-12-01

Since compost is widely used as soil amendment and the fact that during the processing of compost material high amounts of microorganisms are released into the air, we investigated whether compost may act as a carrier for thermophilic methanogens to temperate soils. All eight investigated compost materials showed a clear methane production potential between 0.01 and 0.98 micromol CH(4) g dw(-1)h(-1) at 50 degrees C. Single strand conformation polymorphism (SSCP) and cloning analysis indicated the presence of Methanosarcina thermophila, Methanoculleus thermophilus, and Methanobacterium formicicum. Bioaerosols collected during the turning of a compost pile showed both a highly similar SSCP profile compared to the corresponding compost material and clear methane production during anoxic incubation in selective medium at 50 degrees C. Both observations indicated a considerable release of thermophilic methanogens into the air. To analyse the persistence of compost-borne thermophilic methanogens in temperate oxic soils, we therefore studied their potential activity in compost and compost/soil mixtures, which was brought to a meadow soil, as well as in an agricultural soil fertilised with compost. After 24h anoxic incubation at 50 degrees C, all samples containing compost showed a clear methanogenic activity, even 1 year after application. In combination with the in vitro observed resilience of the compost-borne methanogens against desiccation and UV radiation we assume that compost material acts as an effective carrier for the distribution of thermophilic methanogens by fertilisation and wind.

Polymeric materials and formulation technologies for modified-release tablet development.

Science.gov (United States)

Zarate, J; Igartua, M; Hernández, R M; Pedraz, J L

2009-11-01

Over the last years significant advances have been made in the area of drug delivery with the development of modified-release (MR) dosage forms. The present review is divided into two parts, one dealing with technologies for the design of modified-release drug delivery tablets and the other with the use of synthetic and natural polymers that are capable of controlling drug release.

Impact of pore characteristics of silica materials on loading capacity and release behavior of ibuprofen.

Science.gov (United States)

Numpilai, Thanapha; Muenmee, Suthaporn; Witoon, Thongthai

2016-02-01

Impact of pore characteristics of porous silica supports on loading capacity and release behavior of ibuprofen was investigated. The porous silica materials and ibuprofen-loaded porous silica materials were thoroughly characterized by N2-sorption, thermal gravimetric and derivative weight analyses (TG-DTW), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM), transmission electron microscope (TEM) to determine the physical properties of materials, amount of ibuprofen adsorbed and position of ibuprofen. The detailed characterization reveals that the ibuprofen molecules adsorbed inside the mesopores. Increasing the mesopore size from 5nm to 10nm increased the ibuprofen loading from 0.74 to 0.85mmol/g, respectively. Incorporation of macropore into the structure of porous silica materials enhanced the ibuprofen loading capacity of 11.8-20.3%. The ibuprofen-loaded bimodal meso-macroporous silica materials exhibited the highest dissolution of 92wt.% within an hour. The ibuprofen particles deposited on the external surface of the porous silica materials showed a lower dissolution rate than the ibuprofen adsorbed inside the mesopores due to the formation of ibuprofen crystalline. Copyright © 2015 Elsevier B.V. All rights reserved.

Heat release rate of wood-plastic composites

Science.gov (United States)

N. M. Stark; R. H. White; C. M. Clemons

1997-01-01

Wood-plastic composites are becoming more important as a material that fulfills recycling needs. In this study, fire performance tests were conducted on several compositions of wood and plastic materials using the Ohio State University rate of heat release apparatus. Test results included five-minute average heat release rate in kW/m2 (HRR avg) and maximum heat release...

International conference and workshop on modeling and mitigating the consequences of accidental releases of hazardous materials

International Nuclear Information System (INIS)

Anon.

1995-01-01

This conference was held September 26--29, 1995 in New Orleans, Louisiana. The purpose of this conference was to provide a multidisciplinary forum for exchange of state-of-the-art information on the consequences of accidental releases of hazardous materials. Attention is focused on air dispersion of vapors. Individual papers have been processed separately for inclusion in the appropriate data bases

Reconcentration of radioactive material released to sanitary sewers in accordance with 10 CFR Part 20

International Nuclear Information System (INIS)

Ainsworth, C.C.; Hill, R.L.; Cantrell, K.J.; Kaplan, D.I.; Norton, M.V.; Aaberg, R.L.; Stetar, E.A.

1994-12-01

The US Nuclear Regulatory Commission (NRC), in accordance with 10 CFR 20, and agreement states, in accordance with state regulations, regulates the discharge of radioactive materials into sanitary sewer systems. A one-year study was conducted by Pacific Northwest Laboratory (PNL) for the NRC to assess whether radioactive materials that are dischared to sanitary sewer systems undergo significant reconcentration within the wastewater treatment plants (WWTP) and to determine the physical and/or chemical processes that may result in radionuclide reconcentration within the WWTPs. The study objectives were addressed by collecting information and data on wastewater treatment, relevant geochemical processes, and individual radionuclide behavior in WWTPs from the open literature, NRC reports, EPA surveys, and interviews with NRC licensees and staff of WWTPs that may be impacted by these discharges. Radionuclide mass balance and removal efficiencies were calculated for WWTPs at Oak Ridge, TN; and Erwin, TN, but were not shown to be reliable since the licensee release data generally underestimated the mass of radionuclide that was ultimately found in the sludge. This disparity may be due, in part, to the fact that data available for use in this study were collected to address regulatory concerns and not to perform mass balance calculations. A limited modeling study showed some promise for predicting radionuclide behavior in WWTPS, however, the general applicability of using these empirical models remains uncertain. With the data and models currently available, it is not possible to quantitatively determine the physical and chemical processes that cause reconcentration or to calculate, a priori, reconcentration factors for specific WWTP unit processes or WWTPs in general

Calculation of Doses Due to Accidentally Released Plutonium From An LMFBR

Energy Technology Data Exchange (ETDEWEB)

Fish, B.R.

2001-08-07

Experimental data and analytical models that should be considered in assessing the transport properties of plutonium aerosols following a hypothetical reactor accident have been examined. Behaviors of released airborne materials within the reactor containment systems, as well as in the atmosphere near the reactor site boundaries, have been semiquantitatively predicted from experimental data and analytical models. The fundamental chemistry of plutonium as it may be applied in biological systems has been used to prepare models related to the intake and metabolism of plutonium dioxide, the fuel material of interest. Attempts have been made to calculate the possible doses from plutonium aerosols for a typical analyzed release in order to evaluate the magnitude of the internal exposure hazards that might exist in the vicinity of the reactor after a hypothetical LMFBR (Liquid-Metal Fast Breeder Reactor) accident. Intake of plutonium (using data for {sup 239}Pu as an example) and its distribution in the body were treated parametrically without regard to the details of transport pathways in the environment. To the extent possible, dose-response data and models have been reviewed, and an assessment of their adequacy has been made so that recommended or preferred practices could be developed.

Tracking of Drug Release and Material Fate for Naturally Derived Omega-3 Fatty Acid Biomaterials.

Science.gov (United States)

Faucher, Keith M; Artzi, Natalie; Beck, Moshe; Beckerman, Rita; Moodie, Geoff; Albergo, Theresa; Conroy, Suzanne; Dale, Alicia; Corbeil, Scott; Martakos, Paul; Edelman, Elazer R

2016-03-01

In vitro and in vivo studies were conducted on omega-3 fatty acid-derived biomaterials to determine their utility as an implantable material for adhesion prevention following soft tissue hernia repair and as a means to allow for the local delivery of antimicrobial or antibiofilm agents. Naturally derived biomaterials offer several advantages over synthetic materials in the field of medical device development. These advantages include enhanced biocompatibility, elimination of risks posed by the presence of toxic catalysts and chemical crosslinking agents, and derivation from renewable resources. Omega-3 fatty acids are readily available from fish and plant sources and can be used to create implantable biomaterials either as a stand-alone device or as a device coating that can be utilized in local drug delivery applications. In-depth characterization of material erosion degradation over time using non-destructive imaging and chemical characterization techniques provided mechanistic insight into material structure: function relationship. This in turn guided rational tailoring of the material based on varying fatty acid composition to control material residence time and hence drug release. These studies demonstrate the utility of omega-3 fatty acid derived biomaterials as an absorbable material for soft tissue hernia repair and drug delivery applications.

COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

Energy Technology Data Exchange (ETDEWEB)

S.O. Bader

1999-10-18

The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

International Nuclear Information System (INIS)

S.O. Bader

1999-01-01

The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

Influence of environmental parameters and of their interactions on the release of metal(loid)s from a construction material in hydraulic engineering.

Science.gov (United States)

Schmukat, A; Duester, L; Goryunova, E; Ecker, D; Heininger, P; Ternes, T A

2016-03-05

Besides the leaching behaviour of a construction material under standardised test-specific conditions with laboratory water, for some construction materials it is advisable to test their environmental behaviour also under close to end use conditions. The envisaged end use combined with the product characteristics (e.g. mineral phases) is decisive for the choice of environmental factors that may change the release of substance that potentially cause adverse environmental effects (e.g. fertilisation or ecotoxicity). At the moment an experimental link is missing between mono-factorial standardised test systems and non standardised complex incubation experiments such as mesocosms which are closer to environmental conditions. Multi-factorial batch experiments may have the potential to close the gap. To verify this, batch experiments with copper slag were performed which is used as armour stones in hydraulic engineering. Design of experiments (DoE) was applied to evaluate the impact of pH, ionic strength, temperature and sediment content on the release of As, Cu, Mo, Ni, Pb, Sb and Zn. The study shows that release and sediment-eluent partitioning of metal(loid)s are impacted by interactions between the studied factors. Under the prevalent test conditions sediment acts as a sink enhancing most strongly the release of elements from the material. Copyright © 2015 Elsevier B.V. All rights reserved.

MAXDOSE-SR: A routine release atmospheric dose model used at SRS

International Nuclear Information System (INIS)

Simpkins, A.A.

2000-01-01

MAXDOSE-SR is a PC version of the dosimetry code MAXIGASP, which was used to calculate doses to the maximally exposed offsite individual for routine atmospheric releases of radioactive material at the Savannah River Site (SRS). Complete code description, verification of models, and user's manual have been included in this report. Minimal input is required to run the program, and site specific parameters are used when possible

Characterization and inventories of nuclear materials and wastes for possible future energy scenarios

International Nuclear Information System (INIS)

Arthur, E.D.

1997-10-01

Awareness of the total materials inventory and materials balance associated with differing methods for energy generation is part of present day concerns associated with disparate areas that include atmospheric emissions, resource utilization, health effects, and both current and long term hazards and risks. Nuclear energy, for a number of decades, has been the recipient of significant scrutiny concerning the materials and wastes it generates, particularly in the context of long term solutions to such issues. This paper examines the nuclear materials and waste generation for nuclear energy scenarios spanning the coming century. The paper also briefly addresses wastes (in the form of emissions) from other energy sources and examines requirements associated with backend energy system materials management. Possible future requirements pertaining to CO 2 management are found to place conditions upon waste management generally similar to those for nuclear waste. One example of material flows for the case of coal generation of electricity coupled with carbon sequestration is also given

Roofing Materials Assessment: Investigation of Five Metals in Runoff from Roofing Materials.

Science.gov (United States)

Winters, Nancy; Granuke, Kyle; McCall, Melissa

2015-09-01

To assess the contribution of five toxic metals from new roofing materials to stormwater, runoff was collected from 14 types of roofing materials and controls during 20 rain events and analyzed for metals. Many of the new roofing materials evaluated did not show elevated metals concentrations in the runoff. Runoff from several other roofing materials was significantly higher than the controls for arsenic, copper, and zinc. Notably, treated wood shakes released arsenic and copper, copper roofing released copper, PVC roofing released arsenic, and Zincalume® and EPDM roofing released zinc. For the runoff from some of the roofing materials, metals concentrations decreased significantly over an approximately one-year period of aging. Metals concentrations in runoff were demonstrated to depend on a number of factors, such as roofing materials, age of the materials, and climatic conditions. Thus, application of runoff concentrations from roofing materials to estimate basin-wide releases should be undertaken cautiously.

Source term estimation and the isotopic ratio of radioactive material released from the WIPP repository in New Mexico, USA

International Nuclear Information System (INIS)

Thakur, P.

2016-01-01

lifted its lid to allow release of waste into the underground air. - Highlights: • February 14, 2014 radiation release from the Nation's only TRU waste repository is discussed. • Environmental monitoring results in the vicinity of the WIPP site are presented. • Source term estimation of the radioactive material released is assessed. • The isotopic ratio of the radioactive material release from the WIPP is discussed.

Meticulous Overview on the Controlled Release Fertilizers

Directory of Open Access Journals (Sweden)

Siafu Ibahati Sempeho

2014-01-01

Full Text Available Owing to the high demand for fertilizer formulations that will exhaust the possibilities of nutrient use efficiency (NUE, regulate fertilizer consumption, and lessen agrophysicochemical properties and environmental adverse effects instigated by conventional nutrient supply to crops, this review recapitulates controlled release fertilizers (CRFs as a cutting-edge and safe way to supply crops’ nutrients over the conventional ways. Essentially, CRFs entail fertilizer particles intercalated within excipients aiming at reducing the frequency of fertilizer application thereby abating potential adverse effects linked with conventional fertilizer use. Application of nanotechnology and materials engineering in agriculture particularly in the design of CRFs, the distinctions and classification of CRFs, and the economical, agronomical, and environmental aspects of CRFs has been revised putting into account the development and synthesis of CRFs, laboratory CRFs syntheses and testing, and both linear and sigmoid release features of CRF formulations. Methodical account on the mechanism of nutrient release centring on the empirical and mechanistic approaches of predicting nutrient release is given in view of selected mathematical models. Compositions and laboratory preparations of CRFs basing on in situ and graft polymerization are provided alongside the physical methods used in CRFs encapsulation, with an emphasis on the natural polymers, modified clays, and superabsorbent nanocomposite excipients.

Japanese tea leaves: a possible biological standard reference material

International Nuclear Information System (INIS)

Fuwa, Keiichiro; Notsu, Kenji; Tsunoda, Kin-ichi; Kato, Hideaki; Yamamoto, Yuko.

1978-01-01

Japanese Tea Leaves, prepared by pulverizing with an agate ball mill and sieving with a Saran fiber sieve (50 mesh) were assessed as a possible biological standard reference material for elemental analysis. The metal content of the tea leaves was determined independently at two laboratories using atomic absorption and flame emission spectrometry. Neutron activation analysis was also performed to determine the content (21 elements) of Tea Leaves. For some elements the result from the various methods were compared. The characteristics of Tea Leaves are discussed and the elemental composition is compared to that of Orchard Leaves (NBS SRM, 1571). The most significant characteristic of Tea Leaves was the high manganese content. (auth.)

Diffusivity database (DDB) system for major rocks and buffer materials (Released on 2007/specification)

International Nuclear Information System (INIS)

Tochigi, Yoshikatsu; Shibata, Masahiro; Sato, Haruo; Kitamura, Akira

2007-03-01

The Diffusivity Database (DDB) System developed on early 2006 was upgraded to apply the data of effective diffusion coefficient of the nuclides in the rock matrix for the 'H12: Project to Establish the Scientific and Technical Basis for HLW Disposal in Japan', and the data in the buffer materials from literature survey was newly added. Some functions of data search and selection were reformed to improve the level of convenience. This DDB system (work on MS-Access TM ) is released to the public through Web server managed by JAEA. (author)

W-Cu gradient materials - processing, properties and application possibilities

International Nuclear Information System (INIS)

Joensson, M.; Kieback, B.

2001-01-01

The functionally graded material (FGM) of tungsten with its high thermal and mechanical resistance and copper with its very high thermal and electrical conductivity and ductility expands the application fields of this material in the direction of extreme demands such as plasma facing components in fusion reactors. The PM-production of W-Cu-gradients recommends itself because of the possibility to form the gradient by the mixing of powder components, but is also demanding because of the differences in their sintering behavior and thermal expansions. W-Gu-gradient samples of different concentration profiles have been formed in layers by powder stacking in a die and continuously by centrifugal powder forming. The consolidation routes were determined by the concentration areas of the gradients and encompass liquid phase sintering, pressure assisted solid phase sintering and the application of coated Tungsten powder and sintering additives. The microstructure and the concentration profiles of the samples have been investigated metaliographically and by EDX. The influence of processing and the gradient profile of the properties have been characterized by TRS and the investigation of residual thermal stresses by neutron diffraction. (author)

Incident involving radioactive material at IAEA Safeguards Laboratory - No radioactivity released to environment

International Nuclear Information System (INIS)

2008-01-01

Full text: Pressure build-up in a small sealed sample bottle in a storage safe resulted in plutonium contamination of a storage room at about 02:30 today at the IAEA's Safeguards Analytical Laboratory in Seibersdorf. All indications are that there was no release of radioactivity to the environment. Further monitoring around the laboratory will be undertaken. No one was working in the laboratory at the time. The Laboratory's safety system detected plutonium contamination in the storage room where the safe was located and in two other rooms - subsequently confirmed by a team of IAEA radiation protection experts. The Laboratory is equipped with multiple safety systems, including an air-filtering system to prevent the release of radioactivity to the environment. There will be restricted access to the affected rooms until they are decontaminated. A full investigation of the incident will be conducted. The IAEA has informed the Austrian regulatory authority. The IAEA's Laboratory in Seibersdorf is located within the complex of the Austrian Research Centers Seibersdorf (ARC), about 35 km southeast of Vienna. The laboratory routinely analyses small samples of nuclear material (uranium or plutonium) as part of the IAEA's safeguards verification work. (IAEA)

Pharmacokinetic modeling of 4,4'-methylenedianiline released from reused polyurethane dialyzer potting materials.

Science.gov (United States)

Do Luu, H M; Hutter, J C

2000-01-01

4, 4'-Methylenedianiline (MDA) is a hydrolysis degradation product that can be released from polyurethanes commonly used in medical device applications. MDA is mutagenic and carcinogenic in animals. In humans, it is hepatotoxic, a known contact and respiratory allergen, and a suspected carcinogen. A physiologically based pharmacokinetic (PBPK) model was developed to estimate the absorption, distribution, metabolism, and excretion of MDA in patients exposed to MDA leached from the potting materials of hemodialyzers. A worst-case reuse situation and a single use case were investigated. The PBPK model included five tissue compartments: liver, kidney, gastrointestinal tract, slowly perfused tissues, and richly perfused tissues. Physiological and chemical parameters of a healthy individual used in the model were obtained from the literature. The model was calibrated using previously published kinetic studies of IV administered doses of (14) C-MDA to rats. The model was validated using independent data published for MDA-exposed workers. The PBPK results indicated that dialysis patients who are exposed to MDA released from dialyzers (new or reused) could accumulate low levels of MDA and metabolites (total MDA) over time. Copyright 2000 John Wiley & Sons, Inc.

Influence of environmental parameters and of their interactions on the release of metal(loid)s from a construction material in hydraulic engineering

International Nuclear Information System (INIS)

Schmukat, A.; Duester, L.; Goryunova, E.; Ecker, D.; Heininger, P.; Ternes, T.A.

2016-01-01

Highlights: • DoE supported multi-factorial study on the metal(loid) release from copper slag. • Interactions of four parameters were studied and weighted. • An effective separation method between slag and sediment was established. • The metal(loid) partitioning between sediment, slag and eluent is described. • The knowledge on the potential environmental impact of copper slag is increased. - Abstract: Besides the leaching behaviour of a construction material under standardised test-specific conditions with laboratory water, for some construction materials it is advisable to test their environmental behaviour also under close to end use conditions. The envisaged end use combined with the product characteristics (e.g. mineral phases) is decisive for the choice of environmental factors that may change the release of substance that potentially cause adverse environmental effects (e.g. fertilisation or ecotoxicity). At the moment an experimental link is missing between mono-factorial standardised test systems and non standardised complex incubation experiments such as mesocosms which are closer to environmental conditions. Multi-factorial batch experiments may have the potential to close the gap. To verify this, batch experiments with copper slag were performed which is used as armour stones in hydraulic engineering. Design of experiments (DoE) was applied to evaluate the impact of pH, ionic strength, temperature and sediment content on the release of As, Cu, Mo, Ni, Pb, Sb and Zn. The study shows that release and sediment-eluent partitioning of metal(loid)s are impacted by interactions between the studied factors. Under the prevalent test conditions sediment acts as a sink enhancing most strongly the release of elements from the material.

Influence of environmental parameters and of their interactions on the release of metal(loid)s from a construction material in hydraulic engineering

Energy Technology Data Exchange (ETDEWEB)

Schmukat, A., E-mail: schmukat@harzwasserwerke.de [Harzwasserwerke GmbH, Zur Granetalsperre 8, 38685 Langelsheim (Germany); Federal Institute of Hydrology, Department of Aquatic Chemistry, Am Mainzer Tor 1, 56068 Koblenz (Germany); Duester, L. [Federal Institute of Hydrology, Department of Aquatic Chemistry, Am Mainzer Tor 1, 56068 Koblenz (Germany); Goryunova, E. [Federal Institute of Hydrology, Department of Aquatic Chemistry, Am Mainzer Tor 1, 56068 Koblenz (Germany); KAPP-Chemie GmbH & Co. KG, Industriestr. 2-4, 56357 Miehlen (Germany); Ecker, D.; Heininger, P.; Ternes, T.A. [Federal Institute of Hydrology, Department of Aquatic Chemistry, Am Mainzer Tor 1, 56068 Koblenz (Germany)

2016-03-05

Highlights: • DoE supported multi-factorial study on the metal(loid) release from copper slag. • Interactions of four parameters were studied and weighted. • An effective separation method between slag and sediment was established. • The metal(loid) partitioning between sediment, slag and eluent is described. • The knowledge on the potential environmental impact of copper slag is increased. - Abstract: Besides the leaching behaviour of a construction material under standardised test-specific conditions with laboratory water, for some construction materials it is advisable to test their environmental behaviour also under close to end use conditions. The envisaged end use combined with the product characteristics (e.g. mineral phases) is decisive for the choice of environmental factors that may change the release of substance that potentially cause adverse environmental effects (e.g. fertilisation or ecotoxicity). At the moment an experimental link is missing between mono-factorial standardised test systems and non standardised complex incubation experiments such as mesocosms which are closer to environmental conditions. Multi-factorial batch experiments may have the potential to close the gap. To verify this, batch experiments with copper slag were performed which is used as armour stones in hydraulic engineering. Design of experiments (DoE) was applied to evaluate the impact of pH, ionic strength, temperature and sediment content on the release of As, Cu, Mo, Ni, Pb, Sb and Zn. The study shows that release and sediment-eluent partitioning of metal(loid)s are impacted by interactions between the studied factors. Under the prevalent test conditions sediment acts as a sink enhancing most strongly the release of elements from the material.

Fluoxetine-induced inhibition of synaptosomal [3H]5-HT release: Possible Ca2+-channel inhibition

International Nuclear Information System (INIS)

Stauderman, K.A.; Gandhi, V.C.; Jones, D.J.

1992-01-01

Fluoxetine, a selective 5-Ht uptake inhibitor, inhibited 15 mM K + -induced [ 3 H]5-HT release from rat spinal cord and cortical synaptosomes at concentrations > 0.5 uM. This effect reflected a property shared by another selective 5-HT uptake inhibitor paroxetine but not by less selective uptake inhibitors such as amitriptyline, desipramine, imipramine or nortriptyline. Inhibition of release by fluoxetine was inversely related to both the concentration of K + used to depolarize the synaptosomes and the concentration of external Ca 2+ . Experiments aimed at determining a mechanism of action revealed that fluoxetine did not inhibit voltage-independent release of [ 3 H]5-HT release induced by the Ca 2+ -ionophore A 23187 or Ca 2+ -independent release induced by fenfluramine. Moreover the 5-HT autoreceptor antagonist methiothepin did not reverse the inhibitory actions of fluoxetine on K + -induced release. Further studies examined the effects of fluoxetine on voltage-dependent Ca 2+ channels and Ca 2+ entry

Triggered Release from Polymer Capsules

Energy Technology Data Exchange (ETDEWEB)

Esser-Kahn, Aaron P. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry; Odom, Susan A. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry; Sottos, Nancy R. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Materials Science and Engineering; White, Scott R. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Aerospace Engineering; Moore, Jeffrey S. [Univ. of Illinois, Urbana, IL (United States). Beckman Inst. for Advanced Science and Technology and Dept. of Chemistry

2011-07-06

Stimuli-responsive capsules are of interest in drug delivery, fragrance release, food preservation, and self-healing materials. Many methods are used to trigger the release of encapsulated contents. Here we highlight mechanisms for the controlled release of encapsulated cargo that utilize chemical reactions occurring in solid polymeric shell walls. Triggering mechanisms responsible for covalent bond cleavage that result in the release of capsule contents include chemical, biological, light, thermal, magnetic, and electrical stimuli. We present methods for encapsulation and release, triggering methods, and mechanisms and conclude with our opinions on interesting obstacles for chemically induced activation with relevance for controlled release.

Influence of PCL on the material properties of collagen based biocomposites and in vitro evaluation of drug release

International Nuclear Information System (INIS)

Kanungo, Ivy; Fathima, Nishter Nishad; Rao, Jonnalagadda Raghava; Nair, Balachandran Unni

2013-01-01

Formulation of biodegradable collagen–poly-ε-caprolactone (PCL) based biomaterials for the sustained release of insulin is the main objective of the present work. PCL has been employed to modulate the physico-chemical behavior of collagen to control the drug release. Designed formulations were employed to statistically optimize insulin release parameter profile at different collagen to PCL molar ratios. Circular dichroism, thermoporometry, FTIR, impedance and scanning electron microscopy techniques have been employed to investigate the effect of PCL on hydration dynamics of the collagen molecule, which in turn changes the dissolution parameters of the drug from the systems. Drug entrapment efficiency has been found to be maximum for collagen to PCL molar ratio of 1:2 (> 90%). In vitro dissolution test reveals that 99% of the drug was released from composite at collagen to PCL molar ratio of 1:3 and 1:4 within 2 h, which indicates that hydrophobicity of the matrix results in weak interaction between lipophilic drug and carrier materials. The least burst release was observed for collagen to PCL molar ratio at 1:2 as synergistic interactions between collagen and PCL was maximum at that particular polymer–polymer ratios. The drug release data indicates super case-II transport of drug (n > 1.0). - Graphical abstract: Collagen–poly-ε-caprolactone based biomaterials for the sustained release of insulin were formulated. Circular dichroism, thermoporometry, FTIR, impedance and scanning electron microscopy techniques have been employed to elucidate the effect of PCL on the structure of the collagen and in vitro drug release. The drug release data fitted to the kinetic model indicates super case-II transport due to the combination of diffusion and polymer relaxation/dissolution (n > 1.0). - Highlights: • Poly-ε-caprolactone influences physico-chemical behavior of collagen. • Poly-ε-caprolactone influences in vitro drug release mechanism from biocomposites. �

Porous alkali activated materials with slow alkali release dynamic. Role of composition

International Nuclear Information System (INIS)

Bumanis, G.; Bajare, D.

2018-01-01

Alkali activated materials (AAM) based on calcined metakaolin or illite clay together with waste by-products, such as waste glass or aluminium scrap recycling waste, were tested as value-added materials for pH stabilization in biogas technology where decrease of pH should be avoided. Porous materials with ability to slowly leach alkalis in the water media thus providing continuous control of the pH level were obtained. XRD, FTIR, SEM and titration methods were used to characterize AAM and their leaching properties. It is clear that composition of the material has an important effect on the diffusion of alkali from structure. Namely, higher Si/Al and Na/Al molar ratios may increase pore solution transfer to the leachate. The leaching rate of alkalis from the structure of AAM is high for the first few days, decreasing over time. It was possible to calculate the buffer capacity from the mixture design of AAM. [es

Maxine: A spreadsheet for estimating dose from chronic atmospheric radioactive releases

Energy Technology Data Exchange (ETDEWEB)

Jannik, Tim [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Bell, Evaleigh [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Dixon, Kenneth [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-07-24

MAXINE is an EXCEL© spreadsheet, which is used to estimate dose to individuals for routine and accidental atmospheric releases of radioactive materials. MAXINE does not contain an atmospheric dispersion model, but rather doses are estimated using air and ground concentrations as input. Minimal input is required to run the program and site specific parameters are used when possible. Complete code description, verification of models, and user’s manual have been included.

Melatonin improves memory acquisition under stress independent of stress hormone release

OpenAIRE

Rimmele, U; Spillmann, M; Bärtschi, C; Wolf, O T; Weber, C S; Ehlert, Ulrike; Wirtz, P H

2009-01-01

RATIONALE: Animal studies suggest that the pineal hormone melatonin influences basal stress hormone levels and dampens hormone reactivity to stress. OBJECTIVES: We investigated whether melatonin also has a suppressive effect on stress-induced catecholamine and cortisol release in humans. As stress hormones affect memory processing, we further examined a possible accompanying modulation of memory function. MATERIALS AND METHODS: Fifty healthy young men received a single oral dose of either 3...

NRC's rulemaking to require materials licensees to be financially responsible for cleanup of accidental releases

International Nuclear Information System (INIS)

Seeman, M.J.

1987-01-01

On June 7, 1985, the US Nuclear Regulatory Commission (NRC) published an advance notice of proposed rulemaking (ANPRM) in the Federal Register to address funding for cleanup of accidents and unexpected decontamination by certain materials licensees. The NRC asked for public comment to help them determine whether to amend its regulations to require certain materials and fuel cycle licensees to demonstrate that they possess adequate financial means to pay for cleanup of accidental releases of radioactive materials. If licensees lack adequate financial resources and funds are to available for prompt cleanup, the consequences could be potentially significant for the public, the licencee and the federal government. The purpose of this paper is to explain the purpose and scope of the Commission's proposed regulatory action, as well as describing several accidents that made the Commission consider this action. Additionally, the paper will address other regulatory precedents. Finally, the paper will conclude by generally characterizing the public comments and items of concern raised by commenters

Commercial SNF Accident Release Fractions

Energy Technology Data Exchange (ETDEWEB)

J. Schulz

2004-11-05

The purpose of this analysis is to specify and document the total and respirable fractions for radioactive materials that could be potentially released from an accident at the repository involving commercial spent nuclear fuel (SNF) in a dry environment. The total and respirable release fractions are used to support the preclosure licensing basis for the repository. The total release fraction is defined as the fraction of total commercial SNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. Radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses; this subset of the total release fraction is referred to as the respirable release fraction. Accidents may involve waste forms characterized as: (1) bare unconfined intact fuel assemblies, (2) confined intact fuel assemblies, or (3) canistered failed commercial SNF. Confined intact commercial SNF assemblies at the repository are contained in shipping casks, canisters, or waste packages. Four categories of failed commercial SNF are identified: (1) mechanically and cladding-penetration damaged commercial SNF, (2) consolidated/reconstituted assemblies, (3) fuel rods, pieces, and debris, and (4) nonfuel components. It is assumed that failed commercial SNF is placed into waste packages with a mesh screen at each end (CRWMS M&O 1999). In contrast to bare unconfined fuel assemblies, the

Commercial SNF Accident Release Fractions

International Nuclear Information System (INIS)

Schulz, J.

2004-01-01

The purpose of this analysis is to specify and document the total and respirable fractions for radioactive materials that could be potentially released from an accident at the repository involving commercial spent nuclear fuel (SNF) in a dry environment. The total and respirable release fractions are used to support the preclosure licensing basis for the repository. The total release fraction is defined as the fraction of total commercial SNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. Radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses; this subset of the total release fraction is referred to as the respirable release fraction. Accidents may involve waste forms characterized as: (1) bare unconfined intact fuel assemblies, (2) confined intact fuel assemblies, or (3) canistered failed commercial SNF. Confined intact commercial SNF assemblies at the repository are contained in shipping casks, canisters, or waste packages. Four categories of failed commercial SNF are identified: (1) mechanically and cladding-penetration damaged commercial SNF, (2) consolidated/reconstituted assemblies, (3) fuel rods, pieces, and debris, and (4) nonfuel components. It is assumed that failed commercial SNF is placed into waste packages with a mesh screen at each end (CRWMS M andO 1999). In contrast to bare unconfined fuel assemblies, the

Plasmid DNA is released from nanosized acicular material surface by low molecular weight oligonucleotides: exogenous plasmid acquisition mechanism for penetration intermediates based on the Yoshida effect.

Science.gov (United States)

Yoshida, N; Ide, K

2008-10-01

When a colloidal solution consisting of nanosized acicular material and bacterial cells is stimulated with sliding friction at the interface between the hydrogel and interface-forming material where the frictional coefficient increases rapidly, the nanosized acicular material accompanying the bacterial cells forms a penetration intermediate. This effect is known as the Yoshida effect in honor of its discoverer. Through the Yoshida effect, a novel property in which penetration intermediates incorporate exogenous plasmid DNA has been identified. This report proposes a possible mechanism for exogenous plasmid acquisition by penetration intermediates in the Yoshida effect. Escherichia coli cells, pUC18, and chrysotile were used as recipient cells, plasmid DNA, and nanosized acicular material, respectively. Even when repeatedly washing the mixture consisting of pUC18 and chrysotile, transformation efficiency by pUC18 was stable. Accordingly, pUC18 adsorbed onto chrysotile was introduced into recipient E. coli cells. At saturation, the amount of pUC18 adsorbed onto chrysotile was 0.8-1.2 microg/mg. To investigate whether pUC18 adsorbed on chrysotile is replicated by polymerase, polymerase chain reaction (PCR) was carried out with the chrysotile. Amplification of the beta-lactamase gene coded in pUC18, which was adsorbed onto chrysotile, was strongly inhibited. This suggests that DNA adsorbed onto chrysotile is not replicated in vivo. When we searched for substances to release pUC18 adsorbed onto chrysotile, we found that a 300-bp single- or double-stranded segment of DNA releases pUC18 from chrysotile. Competitive adsorption onto chrysotile between double-stranded DNA and pUC18 was then examined through the Yoshida effect. The 310- and 603-bp double-stranded nucleotides caused 50% competitive inhibition at the same molar ratio with pUC18. Hence, the adsorbed region of pUC18 is about 300 bp in length. As the culture period for recipient cells increases, transformation

Controlled drug release for tissue engineering.

Science.gov (United States)

Rambhia, Kunal J; Ma, Peter X

2015-12-10

Tissue engineering is often referred to as a three-pronged discipline, with each prong corresponding to 1) a 3D material matrix (scaffold), 2) drugs that act on molecular signaling, and 3) regenerative living cells. Herein we focus on reviewing advances in controlled release of drugs from tissue engineering platforms. This review addresses advances in hydrogels and porous scaffolds that are synthesized from natural materials and synthetic polymers for the purposes of controlled release in tissue engineering. We pay special attention to efforts to reduce the burst release effect and to provide sustained and long-term release. Finally, novel approaches to controlled release are described, including devices that allow for pulsatile and sequential delivery. In addition to recent advances, limitations of current approaches and areas of further research are discussed. Copyright © 2015 Elsevier B.V. All rights reserved.

Heat release, time required, and cleaning ability of MTwo R and ProTaper universal retreatment systems in the removal of filling material.

Science.gov (United States)

Bramante, Clovis Monteiro; Fidelis, Natasha Siqueira; Assumpção, Tatiana Santos; Bernardineli, Norberti; Garcia, Roberto Brandão; Bramante, Alexandre Silva; de Moraes, Ivaldo Gomes

2010-11-01

This ex vivo study evaluated the heat release, time required, and cleaning efficacy of MTwo (VDW, Munich, Germany) and ProTaper Universal Retreatment systems (Dentsply/Maillefer, Ballaigues, Switzerland) and hand instrumentation in the removal of filling material. Sixty single-rooted human teeth with a single straight canal were obturated with gutta-percha and zinc oxide and eugenol-based cement and randomly allocated to 3 groups (n = 20). After 30-day storage at 37 °C and 100% humidity, the root fillings were removed using ProTaper UR, MTwo R, or hand files. Heat release, time required, and cleaning efficacy data were analyzed statistically (analysis of variance and the Tukey test, α = 0.05). None of the techniques removed the root fillings completely. Filling material removal with ProTaper UR was faster but caused more heat release. Mtwo R produced less heat release than the other techniques but was the least efficient in removing gutta-percha/sealer. ProTaper UR and MTwo R caused the greatest and lowest temperature increase on root surface, respectively; regardless of the type of instrument, more heat was released in the cervical third. Pro Taper UR needed less time to remove fillings than MTwo R. All techniques left filling debris in the root canals. Copyright © 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

The behaviour of ceramic breeder materials with respect to tritium release and pellet/pebble mechanical integrity

Science.gov (United States)

Kwast, H.; Conrad, R.; May, R.; Casadio, S.; Roux, N.; Werle, H.

1994-09-01

In situ tritium release experiments from several candidate fusion blanket ceramic breeder materials have been performed in the High Flux Reactor (HFR) at Petten over the last few years. The sixth experiment, EXOTIC-6, contained pellets of LiAlO 2, Li 2XrO 3, Li 6Xr 2O 7 and Li 8ZrO 6 and pebbles of Li 4SiO 4 and Li 2ZrO 3 which were irradiated up to a lithium burnup of 3%. A large number of temperature transients and purge gas composition changes were performed. From the temperature transients tritium residence times have been determined. Some preliminary results were presented at the 17th Symposium on Fusion Technology (SOFT) held in Rome in 1992. In the present paper results of a further analysis of the residence times are presented together with some postirradiation examination results. The LiAlO 2 pellets showed a better mechanical stability than the Li-zirconates pellets. The pebbels remained intact. The tritium residence times determined from the tritium inventories were in good agreement with those previously determined from temperature transients. The tritium release characteristics of the materials investigated remain substantially unchanged up to the maximum lithium burnup achieved in this experiment.

The stability of CaS in circulating fluidized bed boiler residue and the possible release of H2S gas to the atmosphere

International Nuclear Information System (INIS)

Mattisson, T.; Lyngfelt, A.

1995-01-01

During the combustion of coal, SO 2 is released to the atmosphere. Because of environmental concerns with acid rain, the capture of SO 2 is an important issue. In fluidized bed combustion SO 2 is captured in-situ by limestone or dolomite to form CaSO 4 . This product is stable and can be disposed of or reused as gypsum. In order to capture the sulphur as CaSO 4 oxidizing conditions are necessary. In a fluidized bed boiler (FBB) CaS may form in regions with reducing conditions, and FBB ashes sampled under irregular operating conditions may contain as much as 50 % of the captured sulphur as CaS. The stability of CaS in a landfill environment is thus very important. It is possible that the sulphide decomposes in the presence of moisture or runoff leachate with the subsequent release of H 2 S gas. This re-release of captured sulphur could have a substantial effect on the overall sulphur capture efficiency, with more sulphur released to the atmosphere than previously thought. In this study the stability of CaS in bed ashes from a 12 MW circulating FBB combusting coal has been investigated, with focus on the release of H 2 S gas. (orig.)

Influence of stabilizer on the environment and their use as possible secondary raw material

International Nuclear Information System (INIS)

Jelenova, M.

2001-01-01

In this paper author deals with the environmental impact of coal combustion in coal fired power plants and with influence of ash and stabilizer on the environment and their use as possible secondary raw material

Advances in Hybrid Polymer-Based Materials for Sustained Drug Release

Directory of Open Access Journals (Sweden)

Lígia N. M. Ribeiro

2017-01-01

Full Text Available The use of biomaterials composed of organic pristine components has been successfully described in several purposes, such as tissue engineering and drug delivery. Drug delivery systems (DDS have shown several advantages over traditional drug therapy, such as greater therapeutic efficacy, prolonged delivery profile, and reduced drug toxicity, as evidenced by in vitro and in vivo studies as well as clinical trials. Despite that, there is no perfect delivery carrier, and issues such as undesirable viscosity and physicochemical stability or inability to efficiently encapsulate hydrophilic/hydrophobic molecules still persist, limiting DDS applications. To overcome that, biohybrid systems, originating from the synergistic assembly of polymers and other organic materials such as proteins and lipids, have recently been described, yielding molecularly planned biohybrid systems that are able to optimize structures to easily interact with the targets. This work revised the biohybrid DDS clarifying their advantages, limitations, and future perspectives in an attempt to contribute to further research of innovative and safe biohybrid polymer-based system as biomaterials for the sustained release of active molecules.

Mexican natural zeolite, material for their possible use in the hydrogen storage

International Nuclear Information System (INIS)

Iturbe G, J. L.; Vazquez A, O.

2009-01-01

In this work a study is presented on the use of a Mexican natural zeolite as possible alternative to storage hydrogen. This zeolite material comes from the Sonora State (Mexico), to which is diminished the particle size by means of a mill treatment with a mechanical alloyed system during 5 hours. Later on, the zeolite in powder form was characterized by means of X-ray diffraction and scanning electron microscopy. It was also exposed to heating in a micro-reactor at 350 C and at the same time making empty during 2 hours, to eliminate humidity and possible gases that were caught in their structure. Soon after, it was diminished the temperature at 10 C and it was contacted with hydrogen of ultra high purity to a pressure of 10 bars during 10 minutes. The hydrogen analysis caught in the zeolite was realized through gas chromatography. The results by means of the chromatograms indicate that the zeolite adsorbed and liberate to hydrogen under conditions completely different to that reported in the literature, being understood that under our experimental conditions to low pressure and temperature, the hydrogen is adsorbed in this material type. (Author)

Delayed Release from Proactive Interference with Meaningful Material: How Much Do We Remember After Reading Brief Prose Passages?

Science.gov (United States)

Blumenthal, Gary B.; Robbins, Donald

1977-01-01

Three experiments were conducted, investigating the buildup of and the release from proactive interference, in which the stimulus materials were brief prose passages about specific topics. Each passage was followed by a multiple-choice test, and then a final test on all the passages read was given. Implications of the data for standardized tests…

21 CFR 181.28 - Release agents.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Release agents. 181.28 Section 181.28 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Release agents. Substances classified as release agents, when migrating from food-packaging material shall...

Cesium release from ceramic waste form materials in simulated canister corrosion product containing solutions

Energy Technology Data Exchange (ETDEWEB)

Vittorio, Luca; Drabarek, Elizabeth; Chronis, Harriet; Griffith, Christopher S

2004-07-01

It has previously been demonstrated that immobilization of Cs{sup +} and/or Sr{sup 2+} sorbed on hexagonal tungsten oxide bronze (HTB) adsorbent materials can be achieved by heating the materials in air at temperatures in the range 500 - 1300 deg C. Highly crystalline powdered HTB materials formed by heating at 800 deg C show leach characteristics comparable to Cs-containing hot-pressed hollandites in the pH range from 0 to 12. As a very harsh leaching test, and also to model in a basic manner, leaching in the presence of canister corrosion products in oxidising environments, leaching of the bronzoid phases has been undertaken in Fe(NO{sub 3}){sub 3} solutions of increasing concentration. This is done in comparison with Cs -hollandite materials in order to compare the leaching characteristics of these two materials under such conditions. Both the Cs-loaded bronze and hollandite materials leach severely in Fe(NO{sub 3}){sub 3} losing virtually all of the immobilized Cs in a period of four days at 150 deg C. Total release of Cs and conversion of hollandite to titanium and iron titanium oxides begins to be observed at relatively low concentrations and is virtually complete after four days reaction in 0.5 mol/L Fe(NO{sub 3}){sub 3}. In the case of the bronze, all of the Cs is also extracted but the HTB structure is preserved. The reaction presumably involves an ion-exchange mechanism and iron oxide with a spinel structure is also observed at high Fe concentrations. (authors)

Cesium release from ceramic waste form materials in simulated canister corrosion product containing solutions

International Nuclear Information System (INIS)

Vittorio, Luca; Drabarek, Elizabeth; Chronis, Harriet; Griffith, Christopher S.

2004-01-01

It has previously been demonstrated that immobilization of Cs + and/or Sr 2+ sorbed on hexagonal tungsten oxide bronze (HTB) adsorbent materials can be achieved by heating the materials in air at temperatures in the range 500 - 1300 deg C. Highly crystalline powdered HTB materials formed by heating at 800 deg C show leach characteristics comparable to Cs-containing hot-pressed hollandites in the pH range from 0 to 12. As a very harsh leaching test, and also to model in a basic manner, leaching in the presence of canister corrosion products in oxidising environments, leaching of the bronzoid phases has been undertaken in Fe(NO 3 ) 3 solutions of increasing concentration. This is done in comparison with Cs -hollandite materials in order to compare the leaching characteristics of these two materials under such conditions. Both the Cs-loaded bronze and hollandite materials leach severely in Fe(NO 3 ) 3 losing virtually all of the immobilized Cs in a period of four days at 150 deg C. Total release of Cs and conversion of hollandite to titanium and iron titanium oxides begins to be observed at relatively low concentrations and is virtually complete after four days reaction in 0.5 mol/L Fe(NO 3 ) 3 . In the case of the bronze, all of the Cs is also extracted but the HTB structure is preserved. The reaction presumably involves an ion-exchange mechanism and iron oxide with a spinel structure is also observed at high Fe concentrations. (authors)

Soft computing analysis of the possible correlation between temporal and energy release patterns in seismic activity

Science.gov (United States)

Konstantaras, Anthony; Katsifarakis, Emmanouil; Artzouxaltzis, Xristos; Makris, John; Vallianatos, Filippos; Varley, Martin

2010-05-01

This paper is a preliminary investigation of the possible correlation of temporal and energy release patterns of seismic activity involving the preparation processes of consecutive sizeable seismic events [1,2]. The background idea is that during periods of low-level seismic activity, stress processes in the crust accumulate energy at the seismogenic area whilst larger seismic events act as a decongesting mechanism releasing considerable energy [3,4]. A dynamic algorithm is being developed aiming to identify and cluster pre- and post- seismic events to the main earthquake following on research carried out by Zubkov [5] and Dobrovolsky [6,7]. This clustering technique along with energy release equations dependent on Richter's scale [8,9] allow for an estimate to be drawn regarding the amount of the energy being released by the seismic sequence. The above approach is being implemented as a monitoring tool to investigate the behaviour of the underlying energy management system by introducing this information to various neural [10,11] and soft computing models [1,12,13,14]. The incorporation of intelligent systems aims towards the detection and simulation of the possible relationship between energy release patterns and time-intervals among consecutive sizeable earthquakes [1,15]. Anticipated successful training of the imported intelligent systems may result in a real-time, on-line processing methodology [1,16] capable to dynamically approximate the time-interval between the latest and the next forthcoming sizeable seismic event by monitoring the energy release process in a specific seismogenic area. Indexing terms: pattern recognition, long-term earthquake precursors, neural networks, soft computing, earthquake occurrence intervals References [1] Konstantaras A., Vallianatos F., Varley M.R. and Makris J. P.: ‘Soft computing modelling of seismicity in the southern Hellenic arc', IEEE Geoscience and Remote Sensing Letters, vol. 5 (3), pp. 323-327, 2008 [2] Eneva M. and

The possibilities of the microwave utilization of wastes on the example of materials containing the asbestos

Directory of Open Access Journals (Sweden)

M. Pigiel

2010-04-01

Full Text Available The presented paper introduce some of the results of the investigations in the utilization of the materials containing asbestos in the existingin Wroclaw University of Technology Institute’s of Technology of Machines and the Automation Foundry and Automation Group themicrowave reactor. In the reactor’s heating chamber there is possible to recycle from 3 up to 5 kg of the batch at once. The temperaturewith which is possible to receive in it is approx. 1400 oC. The time of it’s achievement (in dependence from utilized material can take outfrom 25 up to 40 minutes.

Conductive plastics: comparing alternative nanotechnologies by performance and life cycle release probability

Energy Technology Data Exchange (ETDEWEB)

Neubauer, Nicole; Wohlleben, Wendel, E-mail: wendel.wohlleben@basf.com [Material Physics, GMC/R, BASF SE (Germany); Tomović, Željko, E-mail: zeljko.tomovic@basf.com [BASF Polyurethanes GmbH, GMP/LS (Germany)

2017-03-15

Nanocomposites can be considered safe during their life cycle as long as the nanofillers remain embedded in the matrix. Therefore, a possible release of nanofillers has to be assessed before commercialization. This report addresses possible life cycle release scenarios for carbon nanotubes (CNT), graphene, and carbon black (CB) from a thermoplastic polyurethane (TPU) matrix. The content of each nanofiller was adjusted to achieve the same conductivity level. The nanofillers reduced the rate of nanoscale releases during mechanical processing with decreasing release in the order neat TPU, TPU-CNT, TPU-graphene, and TPU-CB. Released fragments were dominated by the polymer matrix with embedded or surface-protruding nanofillers. During electron microscopy analysis, free CB was observed, however, there was no free CNT or graphene. Quantitatively, the presence of free nanofillers remained below the detection limit of <0.01% of generated dust. Further, both the production process and type of mechanical processing showed a significant impact with higher release rates for injection-molded compared to extruded and sanded compared to drilled materials. Due to its optimal performance for further development, extruded TPU-CNT was investigated in a combined, stepwise worst case scenario (mechanical processing after weathering). After weathering by simulated sunlight and rain, CNT were visible at the surface of the nanocomposite; after additional sanding, fragments showed protruding CNT, but free CNT were not detected. In summary, this preliminary exposure assessment showed no indication that recommended occupational exposure limits for carbonaceous nanomaterials can be exceeded during the life cycle of the specific TPU nanocomposites and conditions investigated in this study.

Comparative Evaluation of Fluoride Releasing Ability of Various Restorative Materials after the Application of Surface Coating Agents – An In-vitro Study

Science.gov (United States)

Kishore, GVS; Sai-Sankar, AJ; Sridhar, M; Pranitha, Kakarla; Sai-Krishna, VS

2016-01-01

Introduction Fluoride plays a key role in prevention of dental caries and is also an essential element for oral health promotion both in children and adults. Aim The aim of the present study was to evaluate the effect of surface coating (petroleum jelly, G-Coat Plus) on the fluoride releasing property of conventional Glass Ionomer Cement (GIC) and Zirconomer. Materials and Methods A total of 30 disk shaped brass mold specimens (6±0.1mm in diameter and 2±0.1mm thickness) for each test group were fabricated with conventional GIC (Group A) and Zirconomer (Group B). These test groups were further divided into three subgroups of 10 each. The unprotected specimens act as control (Group A1 and B1), G-Coat Plus specimens as (Group A2 and B2) and for the remaining specimens petroleum jelly was applied (Group A3 and B3). Fluoride ion concentration was measured with a combination of fluoride ion specific electrode and ion analyzer for every 24 hours for 15 days. The data was statistically analyzed using Kruskal Wallis and Mann-Whitney U test. Results The Group B released significantly more fluoride than Group A. Among all the subgroups the greatest amount of fluoride was released from Group B1, in the first 24 hours followed by A1 and B2. The least was observed on 15th day with Group B3 and A3. Conclusion Both the tested materials (GIC and Zirconomer) used in the study exhibited fluoride release whether protected or unprotected with surface coating. Though there was a difference between the groups, the pattern of fluoride release was similar and continuous throughout the study period i.e., first the initial burst followed by sustained release. The results revealed Zirconomer released more fluoride and is comparable to conventional GIC. PMID:28209001

A guide to TIRION 4 - a computer code for calculating the consequences of releasing radioactive material to the atmosphere

International Nuclear Information System (INIS)

Fryer, L.S.

1978-12-01

TIRION 4 is the most recent program in a series designed to calculate the consequences of releasing radioactive material to the atmosphere. A brief description of the models used in the program and full details of the various control cards necessary to run TIRION 4 are given. (author)

Release of radioactive materials in simulation test of a postulated solvent fire in a nuclear fuel reprocessing plant

International Nuclear Information System (INIS)

Nishio, G.; Hashimoto, K.

1989-01-01

This paper reports on small- and large-scale fire tests performed to examine the adequacy of a safety evaluation method for a solvent fire in the extraction process of a nuclear fuel reprocessing plant. The test objectives were to obtain information on the confinement of radioactive materials during a 30% tri-n-butyl phosphate-n-dodecane fire while air ventilation is operating in the cell. The rates of release of cesium, strontium, cerium, ruthenium, and uranium from a burning solvent were determined. The quantities of species released were obtained from the solvent burning rate, smoke generation rate, partition coefficients of species between solvent and water, and coefficients of species entrainment to atmosphere in cell

Release of radioisotopes and activated materials from nuclear installations and facilities

International Nuclear Information System (INIS)

Manfredi, P.F.; Millaud, J. E.

2001-01-01

This report discusses the problems of release of items from facilities and installations where radiation-based activities have been carried out. Several situations are reviewed and their release problems are discussed in detail. Particular attention is devoted to the assessment of the activity of the items to be released. A correct assessment of the activity will help the decision about the final use of the items removed from the radiation-related facility, either re-use, entering the public market, recycling, disposal and storage under different procedures. Even the final destination of the building which hosted the facility needs to be decided on the basis of an accurate assessment of the residual activity. The assessment of the activity, besides being fundamental in guaranteeing a safe approach to the procedures related to the release may result in a substantial profit. This is the case of items whose level of activity is so low that they can be put on the public market, reused or recycled for final product subject to very stringent radiation safety requirements. It will be shown that detector techniques play a fundamental role in the release process. In particular, the low-level counting techniques are fundamental in establishing whether or not the unrestrained release is feasible or not

Study on the possible consequences of a severe accident in a Swiss nuclear power plant on the drinking water supply

International Nuclear Information System (INIS)

Ustohalova, Veronika; Kueppers, Christian; Claus, Manuel

2014-01-01

The study on the possible consequences of a severe accident in a Swiss nuclear power plant on the drinking water supply covers the following issues: estimation of possible source terms and radioactive materials release rates, airborne water contamination, water contamination by direct pollution, consequences for the drinking water supply, emergency measures in case of a drinking water contamination, routine surveillance of surface and ground water and improvement possibilities in nuclear power plants.

Saturated fatty acid palmitate induces extracellular release of histone H3: A possible mechanistic basis for high-fat diet-induced inflammation and thrombosis

Energy Technology Data Exchange (ETDEWEB)

Shrestha, Chandan [Department of Systems Biology in Thromboregulation, Kagoshima University Graduate School of Medical and Dental Sciences, Kagoshima (Japan); Department of Laboratory and Vascular Medicine, Kagoshima University Graduate School of Medical and Dental Sciences, Kagoshima (Japan); Ito, Takashi [Department of Systems Biology in Thromboregulation, Kagoshima University Graduate School of Medical and Dental Sciences, Kagoshima (Japan); Kawahara, Ko-ichi [Department of Biomedical Engineering, Osaka Institute of Technology, Osaka (Japan); Shrestha, Binita; Yamakuchi, Munekazu; Hashiguchi, Teruto [Department of Laboratory and Vascular Medicine, Kagoshima University Graduate School of Medical and Dental Sciences, Kagoshima (Japan); Maruyama, Ikuro, E-mail: rinken@m3.kufm.kagoshima-u.ac.jp [Department of Systems Biology in Thromboregulation, Kagoshima University Graduate School of Medical and Dental Sciences, Kagoshima (Japan)

2013-08-09

Highlights: •High-fat diet feeding and palmitate induces the release of nuclear protein histone H3. •ROS production and JNK signaling mediates the release of histone H3. •Extracellular histones induces proinflammatory and procoagulant response. -- Abstract: Chronic low-grade inflammation is a key contributor to high-fat diet (HFD)-related diseases, such as type 2 diabetes, non-alcoholic steatohepatitis, and atherosclerosis. The inflammation is characterized by infiltration of inflammatory cells, particularly macrophages, into obese adipose tissue. However, the molecular mechanisms by which a HFD induces low-grade inflammation are poorly understood. Here, we show that histone H3, a major protein component of chromatin, is released into the extracellular space when mice are fed a HFD or macrophages are stimulated with the saturated fatty acid palmitate. In a murine macrophage cell line, RAW 264.7, palmitate activated reactive oxygen species (ROS) production and JNK signaling. Inhibitors of these pathways dampened palmitate-induced histone H3 release, suggesting that the extracellular release of histone H3 was mediated, in part, through ROS and JNK signaling. Extracellular histone activated endothelial cells toexpress the adhesion molecules ICAM-1 and VCAM-1 and the procoagulant molecule tissue factor, which are known to contribute to inflammatory cell recruitment and thrombosis. These results suggest the possible contribution of extracellular histone to the pathogenesis of HFD-induced inflammation and thrombosis.

Saturated fatty acid palmitate induces extracellular release of histone H3: A possible mechanistic basis for high-fat diet-induced inflammation and thrombosis

International Nuclear Information System (INIS)

Shrestha, Chandan; Ito, Takashi; Kawahara, Ko-ichi; Shrestha, Binita; Yamakuchi, Munekazu; Hashiguchi, Teruto; Maruyama, Ikuro

2013-01-01

Highlights: •High-fat diet feeding and palmitate induces the release of nuclear protein histone H3. •ROS production and JNK signaling mediates the release of histone H3. •Extracellular histones induces proinflammatory and procoagulant response. -- Abstract: Chronic low-grade inflammation is a key contributor to high-fat diet (HFD)-related diseases, such as type 2 diabetes, non-alcoholic steatohepatitis, and atherosclerosis. The inflammation is characterized by infiltration of inflammatory cells, particularly macrophages, into obese adipose tissue. However, the molecular mechanisms by which a HFD induces low-grade inflammation are poorly understood. Here, we show that histone H3, a major protein component of chromatin, is released into the extracellular space when mice are fed a HFD or macrophages are stimulated with the saturated fatty acid palmitate. In a murine macrophage cell line, RAW 264.7, palmitate activated reactive oxygen species (ROS) production and JNK signaling. Inhibitors of these pathways dampened palmitate-induced histone H3 release, suggesting that the extracellular release of histone H3 was mediated, in part, through ROS and JNK signaling. Extracellular histone activated endothelial cells toexpress the adhesion molecules ICAM-1 and VCAM-1 and the procoagulant molecule tissue factor, which are known to contribute to inflammatory cell recruitment and thrombosis. These results suggest the possible contribution of extracellular histone to the pathogenesis of HFD-induced inflammation and thrombosis

Role of iron and aluminum coagulant metal residuals and lead release from drinking water pipe materials.

Science.gov (United States)

Knowles, Alisha D; Nguyen, Caroline K; Edwards, Marc A; Stoddart, Amina; McIlwain, Brad; Gagnon, Graham A

2015-01-01

Bench-scale experiments investigated the role of iron and aluminum residuals in lead release in a low alkalinity and high (> 0.5) chloride-to-sulfate mass ratio (CSMR) in water. Lead leaching was examined for two lead-bearing plumbing materials, including harvested lead pipe and new lead: tin solder, after exposure to water with simulated aluminum sulfate, polyaluminum chloride and ferric sulfate coagulation treatments with 1-25-μM levels of iron or aluminum residuals in the water. The release of lead from systems with harvested lead pipe was highly correlated with levels of residual aluminum or iron present in samples (R(2) = 0.66-0.88), consistent with sorption of lead onto the aluminum and iron hydroxides during stagnation. The results indicate that aluminum and iron coagulant residuals, at levels complying with recommended guidelines, can sometimes play a significant role in lead mobilization from premise plumbing.

Evaluation of radiological releases from the Tomsk-7 accident

Energy Technology Data Exchange (ETDEWEB)

Lussie, W.G.

1995-10-01

On April 6, 1993, there was an uncontrolled release of radioactive material from the fuel reprocessing plant at the Siberian Chemical Combine in Tomsk. The release resulted from the rupture of an over-pressurized feed adjustment tank and subsequent explosion that destroyed the walls and roof of the operating gallery. Radioactive material was released through a 150 meter stack, as well as through the destroyed walls and roof. Relatively stable atmospheric conditions prevailed and a light snow was falling. The radiation release was not excessive, but the spread of radioactive material was compounded by the explosion. Radiation was detected about 26 km from the source. This paper summarizes the information available in the US regarding the release and, using reasonable assumptions, compares the calculated ground activity and radiation levels with the reported measured values.

Evaluation of radiological releases from the Tomsk-7 accident

International Nuclear Information System (INIS)

Lussie, W.G.

1995-01-01

On April 6, 1993, there was an uncontrolled release of radioactive material from the fuel reprocessing plant at the Siberian Chemical Combine in Tomsk. The release resulted from the rupture of an over-pressurized feed adjustment tank and subsequent explosion that destroyed the walls and roof of the operating gallery. Radioactive material was released through a 150 meter stack, as well as through the destroyed walls and roof. Relatively stable atmospheric conditions prevailed and a light snow was falling. The radiation release was not excessive, but the spread of radioactive material was compounded by the explosion. Radiation was detected about 26 km from the source. This paper summarizes the information available in the US regarding the release and, using reasonable assumptions, compares the calculated ground activity and radiation levels with the reported measured values

Prevention and mitigation of groundwater contamination from radioactive releases

International Nuclear Information System (INIS)

1988-10-01

This document gives basic information on potential pathways and mechanisms, by which radioactive materials from releases can reach man, and on modelling considerations to predict the behaviour of radioactive materials in the ground. The main objective is to present an overview of existing techniques for preventing the offsite releases of contaminants into the groundwater systems and techniques for mitigation of effects of such releases should they occur. The recommended techniques are fully applicable to any hazardous materials, such as organic liquids, and toxic materials or otherwise dangerous materials, the presence of which in the accessible biosphere can represent health risks as well as economic losses to the general public. 11 refs, 2 figs, 8 tabs

Atmospheric Release Advisory Capability (ARAC)

International Nuclear Information System (INIS)

Dickerson, M.H.

1975-01-01

The chief purpose of ARAC data acquisition program is to provide site officials, who are responsible for ensuring maximum health protection for the endangered site personnel and public, with estimates of the effects of atmospheric releases of hazardous material as rapidly and accurately as possible. ARAC is in the initial stages of being implemented and is therefore susceptible to changes before it reaches its final form. However the concept of ARAC is fully developed and was successfully demonstrated during a feasibility study conducted in June 1974, as a joint effort between the Savannah River Laboratory (SRL) and Lawrence Livermore Laboratory (LLL). Additional tests between SRL and LLL are scheduled for December 1975. While the immediate goal is the application of ARAC to assist a limited number of ERDA sites, the system is designed with sufficient flexibility to permit expanding the service to a large number of sites. Success in ARAC application should provide nuclear facilities with a means to handle better the urgent questions concerning the potential accidental hazards from atmospheric releases in addition to providing the sites with a capability to assess the effort of their normal operations

Radionuclide release and aerosol generation during core debris interactions with concrete

International Nuclear Information System (INIS)

Powers, D.A.

1986-01-01

During severe accidents at nuclear power plants, it is possible for the reactor fuel to melt and penetrate the reactor vessel. This can lead to vigorous interaction of core materials (UO 2 , ZrO 2 , Zr, and stainless steel) with structural concrete. Sparging of the molten core debris by gases (H 2 O and CO 2 ) liberated from the concrete can lead to rapid release of radionuclides from the core debris. A theoretical description of this release process has been developed and is called the VANESA model. The treatments in the VANESA model of the thermodynamics of radionuclide vaporization and the kinetic barriers to vaporization will be described. Predictions obtained from the model will be compared to the results of tests of core debris/concrete interactions

Nanocomposites for controlled release of nitrogen fertilizer

International Nuclear Information System (INIS)

Silva, Viviane J.M. da; Visconte, Leila L.Y.; Nascimento, Regina Sandra V.

2009-01-01

The study aimed at the development of nano structured materials capable of reducing the rate of release of nitrogen in the soil from an agricultural nitrogen fertilizer. Four different systems of polymer composites were prepared: (1) montmorillonite clay/fertilizer, (2) montmorillonite clay/thermoplastic starch and fertilizer, (3) montmorillonite clay/fertilizer, thermoplastic starch and low-density polyethylene (LDPE) and also (4) montmorillonite clay/fertilizer, thermoplastic starch and polycaprolactone. It was confirmed the formation of nano structured materials by elemental analysis (CHN) and X-ray diffraction (XRD). The kinetics of nitrogen release was detected by enzymatic colorimetric analysis and spectroscopy in the ultraviolet/visible. The results showed that all materials evaluated were able to reduce the rate of release of nitrogen in the fertilizers. (author)

Sellafield (release of radioactivity)

Energy Technology Data Exchange (ETDEWEB)

Cunningham, J; Goodlad, A; Morris, M

1986-02-06

A government statement is reported, about the release of plutonium nitrate at the Sellafield site of British Nuclear Fuels plc on 5 February 1986. Matters raised included: details of accident; personnel monitoring; whether radioactive material was released from the site; need for public acceptance of BNFL activities; whether plant should be closed; need to reduce level of radioactive effluent; number of incidents at the plant.

Impact of proposed financial assurance requirements on nuclear materials licensees

International Nuclear Information System (INIS)

Hendrickson, P.L.; Scott, M.J.; Mullen, M.F.; Nicholls, A.K.; Smith, S.A.

1987-09-01

The NRC is considering a possible rulemaking that would require certain nuclear materials licensees to demonstrate financial ability to clean up accidental releases of radioactive materials. The rulemaking would potentially affect approximately 16,350 NRC and Agreement State licensees. This report was prepared for NRC by the Pacific Northwest Laboratory to provide background information and analysis for the potential rulemaking. Specific topics examined in the report include: (1) characteristics of potentially affected licensees, (2) the availability and cost of various financial assurance mechanisms, (3) the financial impacts for licensees (including licensees classified as small businesses) of providing $2M of assurance per licensee and a sliding amount of assurance tied to risk, (4) the cost of administering a financial assurance rule, and (5) overall benefits and costs. Tabular information on past material licensee accidents and cleanup efforts is also included. The financial occurrence mechanism that appears to be most suitable for providing the desired financial assurance is one or more newly formed captive insurance companies. Potential benefits of the rulemaking include reduced need for taxpayer-funded cleanup of accidental releases, reduces administrative time to secure such funds, and the possibility of more cleanup with correspondingly reduced occupational and public exposure to radioactive materials

New possibilities using additive manufacturing with materials that are difficult to process and with complex structures

Science.gov (United States)

Olsson, Anders; Hellsing, Maja S.; Rennie, Adrian R.

2017-05-01

Additive manufacturing (or 3D printing) opens the possibility of creating new designs and manufacturing objects with new materials rapidly and economically. Particularly for use with polymers and polymer composites, simple printers can make high quality products, and these can be produced easily in offices, schools and in workshops and laboratories. This technology has opened a route for many to test ideas or to make custom devices. It is possible to easily manufacture complex geometries that would be difficult or even impossible to create with traditional methods. Naturally this technology has attracted attention in many fields that include the production of medical devices and prostheses, mechanical engineering as well as basic sciences. Materials that are highly problematic to machine can be used. We illustrate process developments with an account of the production of printer parts to cope with polymer fillers that are hard and abrasive; new nozzles with ruby inserts designed for such materials are durable and can be used to print boron carbide composites. As with other materials, complex parts can be printed using boron carbide composites with fine structures, such as screw threads and labels to identify materials. General ideas about design for this new era of manufacturing customised parts are presented.

New possibilities using additive manufacturing with materials that are difficult to process and with complex structures

International Nuclear Information System (INIS)

Olsson, Anders; Hellsing, Maja S; Rennie, Adrian R

2017-01-01

Additive manufacturing (or 3D printing) opens the possibility of creating new designs and manufacturing objects with new materials rapidly and economically. Particularly for use with polymers and polymer composites, simple printers can make high quality products, and these can be produced easily in offices, schools and in workshops and laboratories. This technology has opened a route for many to test ideas or to make custom devices. It is possible to easily manufacture complex geometries that would be difficult or even impossible to create with traditional methods. Naturally this technology has attracted attention in many fields that include the production of medical devices and prostheses, mechanical engineering as well as basic sciences. Materials that are highly problematic to machine can be used. We illustrate process developments with an account of the production of printer parts to cope with polymer fillers that are hard and abrasive; new nozzles with ruby inserts designed for such materials are durable and can be used to print boron carbide composites. As with other materials, complex parts can be printed using boron carbide composites with fine structures, such as screw threads and labels to identify materials. General ideas about design for this new era of manufacturing customised parts are presented. (invited comment)

Minimizing lead release levels in secondary smelters slags

International Nuclear Information System (INIS)

Shenkler, E.S.; Graham, S.; Ghosh, R.; Greenhut, V.A.

1991-01-01

Five lead-containing slags and four mattes were analyzed to reveal microstructure, semi-quantitative microchemistry, and phases present. To determine if the slags could be incorporated as a glass so that lead release levels could be stabilized, glass batches were formulated based on slag compositions. Leaching tests showed that all materials that were fritted in a glass batch had lower lead release levels than non-adjusted materials, and all could satisfy EPA test requirements. The mole ratio of glass modifiers to glass formers played an important role in the extent of lead release. Small additions of phosphate to a batch had a significant effect on lowering lead release levels

Radioactive releases into the environment under accidental conditions

International Nuclear Information System (INIS)

Beninson, D.

1976-01-01

Although accidents involving the release of radioactive materials and the unplanned exposure of people can occur at any stage of the nuclear fuel cycle, most attention has been focused on reactor accidents. Although no power reactor accidents involving exposure of the public have yet occured, it should be recognized that the probability of such accidental releases cannot be reduced to zero. Since the inventory of radioactive materials in power reactors is very large, it is usual to postulate, for safety assessments, that a release of fission products takes place in spite of all protective measures. This postulated release is of importance for reactor siting and for preparing emergency plans. (HP) [de

32 CFR 705.6 - Releasing public information material to the media.

Science.gov (United States)

2010-07-01

... UNITED STATES NAVY REGULATIONS AND OFFICIAL RECORDS PUBLIC AFFAIRS REGULATIONS § 705.6 Releasing public... and/or as approved by the Assistant Secretary of Defense (Public Affairs). (i) Overall responsibility for release of information rests with the Assistant Secretary of Defense (Public Affairs). The Chief...

Concerns in assessing radiological releases to a major estuary

International Nuclear Information System (INIS)

Foldesi, Leslie P.

1989-01-01

Full text: In the State of Virginia, the James River flows into the Chesapeake Bay and from the mouth of the James River to the fall line the river is under the influence of tidal forces. There are several centers of commerce along the river including an international port of call at the mouth of the James. Associated with the centers of commerce are potential sources of radioactive materials for being released to the river. Two hundred miles inland, the Babcock and Wilcox nuclear fuels processing plants are situated along-side the James River, which has been known to flood its banks quickly in the mountainous regions of Virginia. Storage tanks have been swept downstream from this facility in a previous flood. Fortunately, the tanks were not destroyed. Another source of a possible release is the Suny Nuclear Power Station located on the James River about fifty miles from the Chesapeake Bay. In the cities of Norfolk and Newport News, shipyards are fueling and defueling the Navy's nuclear powered fleet. In addition, many of the Navy's ships are carrying nuclear weapons. These activities may also result in an inadvertent release. In assessing the radiological release from any one of the previously mentioned activities, it is obvious that dilution of the material released into the river is a major factor in dose assessment, as well as the fact that the water is brackish and not suitable as a source of potable water. However, dilution in this case may not be the simple solution. We also have to remember that this estuary is under tidal effects, which means that the materials may not be going out to sea to be further diluted as quickly as we would like to think. It may be possible that the material will be carried up river as far as the fall line and deposited, or deposited along the river's banks. From Virginia's experience with the pesticide, Kepone, materials may be deposited along the estuary and enter the food chain thereby necessitating the limitation of taking

Concerns in assessing radiological releases to a major estuary

Energy Technology Data Exchange (ETDEWEB)

Foldesi, Leslie P [Virginia Department of Health, Bureau of Radiological Health, Richmond, VA (United States)

1989-09-01

Full text: In the State of Virginia, the James River flows into the Chesapeake Bay and from the mouth of the James River to the fall line the river is under the influence of tidal forces. There are several centers of commerce along the river including an international port of call at the mouth of the James. Associated with the centers of commerce are potential sources of radioactive materials for being released to the river. Two hundred miles inland, the Babcock and Wilcox nuclear fuels processing plants are situated along-side the James River, which has been known to flood its banks quickly in the mountainous regions of Virginia. Storage tanks have been swept downstream from this facility in a previous flood. Fortunately, the tanks were not destroyed. Another source of a possible release is the Suny Nuclear Power Station located on the James River about fifty miles from the Chesapeake Bay. In the cities of Norfolk and Newport News, shipyards are fueling and defueling the Navy's nuclear powered fleet. In addition, many of the Navy's ships are carrying nuclear weapons. These activities may also result in an inadvertent release. In assessing the radiological release from any one of the previously mentioned activities, it is obvious that dilution of the material released into the river is a major factor in dose assessment, as well as the fact that the water is brackish and not suitable as a source of potable water. However, dilution in this case may not be the simple solution. We also have to remember that this estuary is under tidal effects, which means that the materials may not be going out to sea to be further diluted as quickly as we would like to think. It may be possible that the material will be carried up river as far as the fall line and deposited, or deposited along the river's banks. From Virginia's experience with the pesticide, Kepone, materials may be deposited along the estuary and enter the food chain thereby necessitating the limitation of taking

Influence of CAD/CAM all-ceramic materials on cell viability, migration ability and adenylate kinase release of human gingival fibroblasts and oral keratinocytes.

Science.gov (United States)

Pabst, A M; Walter, C; Grassmann, L; Weyhrauch, M; Brüllmann, D D; Ziebart, T; Scheller, H; Lehmann, K M

2014-05-01

The aim of this study was to analyze the influence of four CAD/CAM all-ceramic materials on cell viability, migration ability and adenylate kinase (ADK) release of human gingival fibroblasts (HGF) and oral keratinocytes (HOK). HGF and HOK were cultured on disc-shaped CAD/CAM all-ceramic materials (e.max CAD LT, e.max CAD HT, Empress CAD and Mark II) and on discs made of tissue culture polystyrene surface (TCPS) serving as control. Cell viability was analyzed by using an MTT assay, and migration ability was investigated by a scratch assay. A ToxiLight assay has been performed to analyze the effect of all-ceramic materials on ADK release and cell apoptosis. At MTT assay for HGF, no significant decrease of cell viability could be detected at all points of measurement (p each > 0.05), while HOK demonstrated a significant decrease in cell viability especially on Empress CAD and Mark II at each point of measurement (p each materials at all points of measurement (between -36 % and -71 %; p each ceramic materials could be investigated. This study disclosed significant differences in cell viability and migration ability of HGF and HOK on CAD/CAM all-ceramic materials. CAD/CAM all-ceramic materials can influence oral cell lines responsible for soft tissue creation which may affect the esthetic outcome.

Analytics of Radioactive Materials Released in the Fukushima Daiichi Nuclear Accident

Energy Technology Data Exchange (ETDEWEB)

Egarievwe, Stephen U. [Nuclear Engineering and Radiological Science Center, Alabama A and M University, Huntsville, AL (United States); Nuclear Engineering Department, University of Tennessee, Knoxville, TN (United States); Coble, Jamie B.; Miller, Laurence F. [Nuclear Engineering Department, University of Tennessee, Knoxville, TN (United States)

2015-07-01

The 2011 Fukushima Daiichi nuclear accident in Japan resulted in the release of radioactive materials into the atmosphere, the nearby sea, and the surrounding land. Following the accident, several meteorological models were used to predict the transport of the radioactive materials to other continents such as North America and Europe. Also of high importance is the dispersion of radioactive materials locally and within Japan. Based on the International Atomic Energy Agency (IAEA) Convention on Early Notification of a nuclear accident, several radiological data sets were collected on the accident by the Japanese authorities. Among the radioactive materials monitored, are I-131 and Cs-137 which form the major contributions to the contamination of drinking water. The radiation dose in the atmosphere was also measured. It is impractical to measure contamination and radiation dose in every place of interest. Therefore, modeling helps to predict contamination and radiation dose. Some modeling studies that have been reported in the literature include the simulation of transport and deposition of I-131 and Cs-137 from the accident, Cs-137 deposition and contamination of Japanese soils, and preliminary estimates of I-131 and Cs-137 discharged from the plant into the atmosphere. In this paper, we present statistical analytics of I-131 and Cs-137 with the goal of predicting gamma dose from the Fukushima Daiichi nuclear accident. The data sets used in our study were collected from the IAEA Fukushima Monitoring Database. As part of this study, we investigated several regression models to find the best algorithm for modeling the gamma dose. The modeling techniques used in our study include linear regression, principal component regression (PCR), partial least square (PLS) regression, and ridge regression. Our preliminary results on the first set of data showed that the linear regression model with one variable was the best with a root mean square error of 0.0133 μSv/h, compared

Analytics of Radioactive Materials Released in the Fukushima Daiichi Nuclear Accident

International Nuclear Information System (INIS)

Egarievwe, Stephen U.; Coble, Jamie B.; Miller, Laurence F.

2015-01-01

The 2011 Fukushima Daiichi nuclear accident in Japan resulted in the release of radioactive materials into the atmosphere, the nearby sea, and the surrounding land. Following the accident, several meteorological models were used to predict the transport of the radioactive materials to other continents such as North America and Europe. Also of high importance is the dispersion of radioactive materials locally and within Japan. Based on the International Atomic Energy Agency (IAEA) Convention on Early Notification of a nuclear accident, several radiological data sets were collected on the accident by the Japanese authorities. Among the radioactive materials monitored, are I-131 and Cs-137 which form the major contributions to the contamination of drinking water. The radiation dose in the atmosphere was also measured. It is impractical to measure contamination and radiation dose in every place of interest. Therefore, modeling helps to predict contamination and radiation dose. Some modeling studies that have been reported in the literature include the simulation of transport and deposition of I-131 and Cs-137 from the accident, Cs-137 deposition and contamination of Japanese soils, and preliminary estimates of I-131 and Cs-137 discharged from the plant into the atmosphere. In this paper, we present statistical analytics of I-131 and Cs-137 with the goal of predicting gamma dose from the Fukushima Daiichi nuclear accident. The data sets used in our study were collected from the IAEA Fukushima Monitoring Database. As part of this study, we investigated several regression models to find the best algorithm for modeling the gamma dose. The modeling techniques used in our study include linear regression, principal component regression (PCR), partial least square (PLS) regression, and ridge regression. Our preliminary results on the first set of data showed that the linear regression model with one variable was the best with a root mean square error of 0.0133 μSv/h, compared

Characterization of nanoparticles released during construction of photocatalytic pavements using engineered nanoparticles

International Nuclear Information System (INIS)

Dylla, Heather; Hassan, Marwa M.

2012-01-01

With the increasing use of titanium dioxide (TiO 2 ) nanoparticles in self-cleaning materials such as photocatalytic concrete pavements, the release of nanoparticles into the environment is inevitable. Nanoparticle concentration, particle size, surface area, elemental composition, and surface morphology are pertinent to determine the associated risks. In this study, the potential of exposure to synthetic nanoparticles released during construction activities for application of photocatalytic pavements was measured during laboratory-simulated construction activities of photocatalytic mortar overlays and in an actual field application of photocatalytic spray coat. A scanning mobility particle sizer system measured the size distribution of nanoparticles released during laboratory and field activities. Since incidental nanoparticles are released during construction activities, nanoparticle emissions were compared to those from similar activities without nano-TiO 2 . Nanoparticle counts and size distribution suggest that synthetic nanoparticles are released during application of photocatalytic pavements. In order to identify the nanoparticle source, nanoparticles were also collected for offline characterization using transmission electron microscopy. However, positive identification of synthetic nanoparticles was not possible due to difficulties in obtaining high-resolution images. As a result, further research is recommended to identify nanoparticle composition and sources.

Controlled release of ibuprofen by meso-macroporous silica

Science.gov (United States)

Santamaría, E.; Maestro, A.; Porras, M.; Gutiérrez, J. M.; González, C.

2014-02-01

Structured meso-macroporous silica was successfully synthesized from an O/W emulsion using decane as a dispersed phase. Sodium silicate solution, which acts as a silica source and a poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (EO19PO39EO19) denoted as P84 was used in order to stabilize the emulsion and as a mesopore template. The materials obtained were characterized through transmission electron microscopy (TEM), scanning electron microscopy (SEM), small-angle X-ray diffraction scattering (SAXS) and nitrogen adsorption-desorption isotherms. Ibuprofen (IBU) was selected as the model drug and loaded into ordered meso-macroporous materials. The effect of the materials’ properties on IBU drug loading and release was studied. The results showed that the loading of IBU increases as the macropore presence in the material is increased. The IBU adsorption process followed the Langmuir adsorption isotherm. A two-step release process, consisting of an initial fast release and then a slower release was observed. Macropores enhanced the adsorption capacity of the material; this was probably due to the fact that they allowed the drug to access internal pores. When only mesopores were present, ibuprofen was probably adsorbed on the mesopores close to the surface. Moreover, the more macropore present in the material, the slower the release behaviour observed, as the ibuprofen adsorbed in the internal pores had to diffuse along the macropore channels up to the surface of the material. The material obtained from a highly concentrated emulsion was functionalized with amino groups using two methods, the post-grafting mechanism and the co-condensation mechanism. Both routes improve IBU adsorption in the material and show good behaviour as a controlled drug delivery system.

Status and possible prospects of an international fusion materials irradiation facility

International Nuclear Information System (INIS)

Cozzani, F.

1999-01-01

Structural materials for future DT fusion power reactors will have to operate under intense neutron fields with energies up to 14 MeV and fluences in the order of 2 MW/m 2 per year. As environmental acceptability, safety considerations and economic viability will be ultimately the keys to the widespread introduction of fusion power, the development of radiation-resistant and low activation materials would contribute significantly to fusion development. For this purpose, testing of materials under irradiation conditions close to those expected in a fusion power station would require the availability, in an appropriate time framework, of an intense, high-energy neutron source. Recent advances in linear accelerator technology, in small specimens testing technology, and in the comprehension of damage phenomena, lead to the conclusion that an accelerator-based D-Li neutron source, with beam energy variability, would provide the most realistic option for a fusion materials testing facility. Under the auspices of the IEA, an international effort (EU, Japan, US, RF) to carry out the conceptual design activities (CDA) of an international fusion materials irradiation facility (IFMIF), based on the D-Li concept, have been carried out successfully. A final conceptual design report was produced at the end of 1996. A phase of conceptual design evaluation (CDE), presently underway, is extending and further refining some of the conceptual design details of IFMIF. The results indicate that an IFMIF-class installation would be technically feasible and could meet its mission objectives. However, a suitable phase of Engineering Validation, to carry out some complementary R and D and prototyping, would still be needed to resolve a few key technical uncertainties before the possibility to proceed toward detailed design and construction could be explored. (orig.)

The development of the American national standard, ''control of radioactive surface contamination on materials, equipment and facilities to be released for uncontrolled use''

International Nuclear Information System (INIS)

Shapiro, J.

1980-01-01

The American National Standard, Control of Radioactive Surface Contamination on Materials, Equipment and Facilities to be Released for Uncontrolled Use, was developed under the procedures of ANSI for ANSI Main Committee N13 (Radiation Protection) by a working group of the Health Physics Society Standards Committee. This standard provides criteria for the control of materials, equipment and facilities contaminated with radioactivity proposed to be released for uncontrolled use. Permissible contamination limits are specified as well as methods assessing the levels of contamination. This paper reviews the proceedings of the Subcommittee on Radioactive Surface Contamination, the comments received by reviewers of the standard, the resolution of the committee, and the bases for reaching the final limits, recommendations, and measurement procedures. (H.K.)

Massive radiological releases profoundly differ from controlled releases

International Nuclear Information System (INIS)

Pascucci-Cahen, Ludivine; Patrick, Momal

2013-01-01

In this article, the authors report identification and assessment of different types of costs associated with nuclear accidents. They first outline that these cost assessments must be as exhaustive or comprehensive as possible. While referring to past accidents, they define the different categories of costs: on-site costs (decontamination and dismantling, electricity not produced on the site), off-site costs (health costs, psychological costs, farming losses), image-related costs (impact on food and farm product exports, decrease of other exports), costs related to energy production, costs related to contaminated areas (refugees, lands). They give an assessment of a severe nuclear accident (i.e. an accident with important but controlled radiological releases) in France and outline that it would be a national catastrophe which could be however managed. They discuss the possible variations of the estimated costs. Then, they show that a major accident (i.e. an accident with massive radiological releases) in France would be an unmanageable European catastrophe because of the radiological consequences, of high economic costs, and of huge losses

PAVAN: an atmospheric-dispersion program for evaluating design-basis accidental releases of radioactive materials from nuclear power stations

International Nuclear Information System (INIS)

Bander, T.J.

1982-11-01

This report provides a user's guide for the NRC computer program, PAVAN, which is a program used by the US Nuclear Regulatory Commission to estimate downwind ground-level air concentrations for potential accidental releases of radioactive material from nuclear facilities. Such an assessment is required by 10 CFR Part 100 and 10 CFR Part 50. The program implements the guidance provided in Regulatory Guide 1.145, Atmospheric Dispersion Models for Potential Accident Consequence Assessments at Nuclear Power Plants. Using joint frequency distributions of wind direction and wind speed by atmospheric stability, the program provides relative air concentration (X/Q) values as functions of direction for various time periods at the exclusion area boundary (EAB) and the outer boundary of the low population zone (LPZ). Calculations of X/Q values can be made for assumed ground-level releases (e.g., through building penetrations and vents) or elevated releases from free-standing stacks. Various options may be selected by the user. They can account for variation in the location of release points, additional plume dispersion due to building wakes, plume meander under low wind speed conditions, and adjustments to consider non-straight trajectories. It computes an effective plume height using the physical release height which can be reduced by inputted terrain features. It cannot handle multiple emission sources. A description of the main program and all subroutines is provided. Also included as appendices are a complete listing of the program and two test cases with the required data inputs and the resulting program outputs

Computer program for prediction of the deposition of material released from fixed and rotary wing aircraft

Science.gov (United States)

Teske, M. E.

1984-01-01

This is a user manual for the computer code ""AGDISP'' (AGricultural DISPersal) which has been developed to predict the deposition of material released from fixed and rotary wing aircraft in a single-pass, computationally efficient manner. The formulation of the code is novel in that the mean particle trajectory and the variance about the mean resulting from turbulent fluid fluctuations are simultaneously predicted. The code presently includes the capability of assessing the influence of neutral atmospheric conditions, inviscid wake vortices, particle evaporation, plant canopy and terrain on the deposition pattern.

Release of fission products from irradiated aluminide fuel at high temperature

International Nuclear Information System (INIS)

Shibata, Toshikazu; Kanda, Keiji; Mishima, Kaichiro; Tamai, Tadaharu; Hayashi, Masatoshi; Snelgrove, James L.; Stahl, David; Matos, James E.; Travelli, Armando; Case, F. Neil; Posey, John C.

1983-01-01

Irradiated uranium aluminide fuel plates of 40% U-235 enrichment were heated for the determination of fission products released under flowing helium gas at temperatures up to and higher than the melting point of fuel cladding material. The release of fission products from the fuel plate at temperature below 500 deg. C was found negligible. The first rapid release of fission products was observed with the occurrence of blistering at 561±1 deg. C on the plates. The next release at 585. C might be caused by melting of the cladding material of 6061-Al alloy. The last release of fission product gases was occurred at the eutectic temperature of 640 deg. C of U-Al x . The released material was mostly xenon, but small amounts of iodine and cesium were observed. (author)

Release of fission products from irradiated aluminide fuel at high temperature

International Nuclear Information System (INIS)

Shibata, T.; Kanda, K.; Mishima, K.

1982-01-01

Irradiated uranium aluminide fuel plates of 40% U-235 enrichment were heated for the determination of fission products released under flowing helium gas at temperatures up to and higher than the melting point of fuel-cladding material. The release of fission products from the fuel plate at temperature below 500 0 C was found negligible. The firist rapid release of fission products was observed with the occurrence of blistering at 561 +- 1 0 C on the plates. The next release at 585 0 C might be caused by melting of the cladding material of 6061-Al alloy. The last release of fission product gases was occurred at the eutectic temperature of 640 0 C of U-Al/sub x/. The released material was mostly xenon, but small amounts of iodine and cesium were observed

Controlled release of ibuprofen by meso–macroporous silica

Energy Technology Data Exchange (ETDEWEB)

Santamaría, E., E-mail: esthersantamaria@ub.edu; Maestro, A.; Porras, M.; Gutiérrez, J.M.; González, C.

2014-02-15

Structured meso–macroporous silica was successfully synthesized from an O/W emulsion using decane as a dispersed phase. Sodium silicate solution, which acts as a silica source and a poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) (EO{sub 19}PO{sub 39}EO{sub 19}) denoted as P84 was used in order to stabilize the emulsion and as a mesopore template. The materials obtained were characterized through transmission electron microscopy (TEM), scanning electron microscopy (SEM), small-angle X-ray diffraction scattering (SAXS) and nitrogen adsorption–desorption isotherms. Ibuprofen (IBU) was selected as the model drug and loaded into ordered meso–macroporous materials. The effect of the materials’ properties on IBU drug loading and release was studied. The results showed that the loading of IBU increases as the macropore presence in the material is increased. The IBU adsorption process followed the Langmuir adsorption isotherm. A two-step release process, consisting of an initial fast release and then a slower release was observed. Macropores enhanced the adsorption capacity of the material; this was probably due to the fact that they allowed the drug to access internal pores. When only mesopores were present, ibuprofen was probably adsorbed on the mesopores close to the surface. Moreover, the more macropore present in the material, the slower the release behaviour observed, as the ibuprofen adsorbed in the internal pores had to diffuse along the macropore channels up to the surface of the material. The material obtained from a highly concentrated emulsion was functionalized with amino groups using two methods, the post-grafting mechanism and the co-condensation mechanism. Both routes improve IBU adsorption in the material and show good behaviour as a controlled drug delivery system. - Graphical abstract: Ibuprofen release profiles for the materials obtained from samples P84{sub m}eso (black diamonds), P84{sub 2}0% (white squares), P84{sub 5

Controlled release of ibuprofen by meso–macroporous silica

International Nuclear Information System (INIS)

Santamaría, E.; Maestro, A.; Porras, M.; Gutiérrez, J.M.; González, C.

2014-01-01

Structured meso–macroporous silica was successfully synthesized from an O/W emulsion using decane as a dispersed phase. Sodium silicate solution, which acts as a silica source and a poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) (EO 19 PO 39 EO 19 ) denoted as P84 was used in order to stabilize the emulsion and as a mesopore template. The materials obtained were characterized through transmission electron microscopy (TEM), scanning electron microscopy (SEM), small-angle X-ray diffraction scattering (SAXS) and nitrogen adsorption–desorption isotherms. Ibuprofen (IBU) was selected as the model drug and loaded into ordered meso–macroporous materials. The effect of the materials’ properties on IBU drug loading and release was studied. The results showed that the loading of IBU increases as the macropore presence in the material is increased. The IBU adsorption process followed the Langmuir adsorption isotherm. A two-step release process, consisting of an initial fast release and then a slower release was observed. Macropores enhanced the adsorption capacity of the material; this was probably due to the fact that they allowed the drug to access internal pores. When only mesopores were present, ibuprofen was probably adsorbed on the mesopores close to the surface. Moreover, the more macropore present in the material, the slower the release behaviour observed, as the ibuprofen adsorbed in the internal pores had to diffuse along the macropore channels up to the surface of the material. The material obtained from a highly concentrated emulsion was functionalized with amino groups using two methods, the post-grafting mechanism and the co-condensation mechanism. Both routes improve IBU adsorption in the material and show good behaviour as a controlled drug delivery system. - Graphical abstract: Ibuprofen release profiles for the materials obtained from samples P84 m eso (black diamonds), P84 2 0% (white squares), P84 5 0% (black triangles), P84 7

The transport of hazardous materials

International Nuclear Information System (INIS)

Goemmel, F.

1987-01-01

The rapid development of all kinds of transports has been leading to a continuously increasing number of accidents involving the release and escape of hazardous materials. The risks involved for men and the environment have to be realized and reduced to a minimum. Efforts in this field have meanwhile been accumulating an enormous quantity of rules, recommendations and regulations. They comprise, among others, both national and international rail transport, maritime transport, inland shipping, air and road transport regulations adding up to a total of about 5000 pages. The publication discusses the necessity and justification of the existing quantity of regulations, it deals with their possible simplification and modified user-oriented arrangement as well as with a possible international harmonization of regulations. Apart from giving a general survey of the transport of hazardous materials the author reviews the intensive efforts which are going into the safety of the transport of hazardous materials and points out technical and legal problems which have remained unsolved so far. The publication essentially contributes to clearing up the background, perspectives and prospects of the complex regulations controlling the transport of hazardous materials. (orig./HP) [de

Apparatus for dynamic measurement of gases released from materials heated under programmed temperature-time control

International Nuclear Information System (INIS)

Early, J.W.; Abernathey, R.M.

1982-04-01

This apparatus, a prototype of one being constructed for hotcell examination of irradiated nuclear materials, measures dynamic release rates and integrated volumes of individual gases from materials heated under controlled temperature-time programs. It consists of an inductively heated vacuum furnace connected to a quadrupole mass spectrometer. A computerized control system with data acquisition provides scanning rates down to 1s and on-line tabular and graphic displays. Heating rates are up to 1300 0 C/min to a maximum temperature of 2000 0 C. The measurement range is about 10 -6 to 10 -2 torr-liter/s for H 2 , CH 4 , H 2 O, N 2 , and CO and 10 -8 to 10 -2 torr-liter/s for He, Kr, and Xe. Applications are described for measurements of Kr and Xe in mixed oxide fuel, various gases in UO 2 pellets, and He in 238 PuO 2 power and heat sources

Growth hormone (GH)-releasing activity of chicken GH-releasing hormone (GHRH) in chickens.

Science.gov (United States)

Harvey, S; Gineste, C; Gaylinn, B D

2014-08-01

Two peptides with sequence similarities to growth hormone releasing hormone (GHRH) have been identified by analysis of the chicken genome. One of these peptides, chicken (c) GHRH-LP (like peptide) was previously found to poorly bind to chicken pituitary membranes or to cloned and expressed chicken GHRH receptors and had little, if any, growth hormone (GH)-releasing activity in vivo or in vitro. In contrast, a second more recently discovered peptide, cGHRH, does bind to cloned and expressed cGHRH receptors and increases cAMP activity in transfected cells. The possibility that this peptide may have in vivo GH-releasing activity was therefore assessed. The intravenous (i.v.) administration of cGHRH to immature chickens, at doses of 3-100 μg/kg, significantly increased circulating GH concentrations within 10 min of injection and the plasma GH levels remained elevated for at least 30 min after the injection of maximally effective doses. The plasma GH responses to cGHRH were comparable with those induced by human (h) or porcine (p) GHRH preparations and to that induced by thyrotropin releasing hormone (TRH). In marked contrast, the i.v. injection of cGHRH-LP had no significant effect on circulating GH concentrations in immature chicks. GH release was also increased from slaughterhouse chicken pituitary glands perifused for 5 min with cGHRH at doses of 0.1 μg/ml or 1.0 μg/ml, comparable with GH responses to hGHRH1-44. In contrast, the perifusion of chicken pituitary glands with cGHRH-LP had no significant effect on GH release. In summary, these results demonstrate that cGHRH has GH-releasing activity in chickens and support the possibility that it is the endogenous ligand of the cGHRH receptor. Copyright © 2014 Elsevier Inc. All rights reserved.

Effects of sorption hysteresis on radionuclide releases from waste packages

International Nuclear Information System (INIS)

Barney, G.S.; Reed, D.T.

1985-01-01

A one-dimensional, numerical transport model was used to calculate radionuclide releases from waste packages emplaced in a nuclear waste repository in basalt. The model incorporates both sorption and desorption isotherm parameters measured previously for sorption of key radionuclides on the packing material component of the waste package. Sorption hysteresis as described by these isotherms lowered releases of some radionuclides by as much as two orders of magnitude. Radionuclides that have low molar inventories (relative to uranium), high solubility, and strongly sorbed, are most affected by sorption hysteresis. In these cases, almost the entire radionuclide inventory is sorbed on the packing material. The model can be used to help optimize the thickness of the packing material layer by comparing release rate versus packing material thickness curves with Nuclear Regulatory Commission (NRC) and Environmental Protection Agency (EPA) release limits

Borehole sealing literature review of performance requirements and materials

International Nuclear Information System (INIS)

Piccinin, D.; Hooton, R.D.

1985-02-01

To ensure the safe disposal of nuclear wastes, all potential pathways for radionuclide release to the biosphere must be effectively sealed. This report presents a summary of the literature up to August 1982 and outlines the placement, mechanical property and durability-stability requirements for borehole sealing. An outline of the materials that have been considered for possible use in borehole sealing is also included. Cement grouts are recommended for further study since it is indicated in the literature that cement grouts offer the best opportunity of effectively sealing boreholes employing present technology. However, new and less well known materials should also be researched to ensure that the best possible borehole plugging system is developed. 78 refs

Flightless mutants in the melon fly and oriental fruit fly (Diptera: Tephritidae) and their possible role in the sterile insect release method

International Nuclear Information System (INIS)

McCombs, S.D.; Saul, S.H.

1992-01-01

Two new mutants that affect adult wing morphology and render the flies incapable of flight.sbd.bubble wing (bw) in the melon fly, Bactrocera cucurbitae (Coquillett), and small wing (sw) in the oriental fruit fly, Bactrocera dorsalis (Hendel).sbd.are described. Both mutants have variable expression and are caused by autosomal, recessive genes. We discuss the possible role of these alleles in constructing genetic sex sorting systems to improve the effectiveness and efficiency of the sterile insect release method

Release Mathematical Model of Active Agent from Packaging Material into Food

Directory of Open Access Journals (Sweden)

Xiuling Huang

2013-01-01

Full Text Available Active packaging is an innovative packaging technology by which active compounds are released from the package to enhance the quality and microbial safety for a wide range of foods. The problem of active ingredient release through the bilayer packaging food system is studied from a theoretical viewpoint. A release model is built to provide predictions of concentration and amount of active ingredient. The equations are built based on Fickian diffusion, and numerical solutions are obtained through finite difference. Different diffusion coefficients DP and DC of active ingredient in different packaging layers, partition coefficient kCP at the interface of outer layer and inner layer, partition coefficient kFC at the interface of inner layer and food, and mass transfer coefficient hm at the interface of inner layer and food are considered in the model. The effects of kCP, thicknesses of outer layer and inner layer, CP0, DP, DC, kFC, and hm on the release are discussed. Corresponding conclusions and analysis are given.

Possibilities of avoidance and control of bacterial plant diseases when using pathogen-tested (certified) or - treated planting material

NARCIS (Netherlands)

Janse, J.; Wenneker, M.

2002-01-01

Testing of planting material for freedom from phytopathogenic bacteria is an important, although not exclusive, method for control of bacterial diseases of plants. Ideally, pathogen-free or pathogen-/disease-resistant planting material is desirable, but this situation is not always possible on a

Material requirements planning: a better way to plan material.

Science.gov (United States)

Tomas, S

1990-08-01

MRP systems can benefit hospitals in their management of material. Systems provide the means to schedule surgical procedures, calculate material requirements, release orders, plan future capacity requirements, and release and track work orders. MRP can be a powerful tool if properly implemented. All it takes is individuals dedicated to maintaining the discipline and data integrity required to make MRP successful.

Environmental releases for calendar year 1996

International Nuclear Information System (INIS)

Greager, E.M.

1997-01-01

This report presents data on radioactive and nonradioactive materials released into the environment during calendar year 1996 from facilities and activities managed by the Fluor Daniel Hanford, Incorporated (formerly the Westinghouse Hanford Company) and Bechtel Hanford, Incorporated. Fluor Daniel Hanford, Incorporated provides effluent monitoring services for Bechtel Hanford, Incorporated, which includes release reporting. Both summary and detailed presentations of the environmental releases are provided. When appropriate, comparisons to data from previous years are made

Environmental releases for calendar year 1996

Energy Technology Data Exchange (ETDEWEB)

Greager, E.M.

1997-07-31

This report presents data on radioactive and nonradioactive materials released into the environment during calendar year 1996 from facilities and activities managed by the Fluor Daniel Hanford, Incorporated (formerly the Westinghouse Hanford Company) and Bechtel Hanford, Incorporated. Fluor Daniel Hanford, Incorporated provides effluent monitoring services for Bechtel Hanford, Incorporated, which includes release reporting. Both summary and detailed presentations of the environmental releases are provided. When appropriate, comparisons to data from previous years are made.

Preparation of venlafaxine hydrochloride sustained-release tablets

Directory of Open Access Journals (Sweden)

GUO Lingling

2013-08-01

Full Text Available To prepare venlafxine hydrochloride sustained-release tablets.Hydroxypropylmethyl cellulose(HPMC and methyl cellulose(MC were used as main materials to prepare sustained-release tablets of velafaxine hydrochloride and the influence of important factors on in vitro release curves of venlafaxine hydrochloride sustained-release tablets was investigated.Results:The optimal prescription included 100 mg HPMC,25 mg MC,and 2.5% glidant in one tablet prepared with 30kN.The tablets were prepared with the method of wet granulation by NO.16 mesh sieve.The tablets exhibited good sustained-release property in phosphate buffered solution (pH=6.8.The as-prepared venlafxine hydrochloride sustained-release tablets have good sustained-release property.

Screening Risk Assessment for Possible Radionuclides in the Amchitka Marine Environment

Energy Technology Data Exchange (ETDEWEB)

NNSA/NV

2002-10-31

As part of its environmental stewardship program the U.S. Department of Energy (DOE) is reevaluating three sites where underground nuclear tests were conducted in the deep subsurface of Amchitka Island, Alaska. The tests (i.e., Long Shot, Milrow, and Cannikin) were conducted in 1965, 1969, and 1971, respectively. Extensive investigations were conducted on these tests and their effect on the environment. Evaluations at the time of testing indicated limited release of radionuclides and absence of risk related to the testing; however, these are being reevaluated under the current DOE environmental stewardship program. A screening risk assessment of potential radionuclide release into the marine environment is an important part of this reevaluation. The risk assessment is one of three interrelated activities: a groundwater model and this screening risk assessment, both of which guide the decisions in the third activity, the site closure plan. Thus, the overall objective of the work is to understand, and subsequently manage, any risk to humans and the environment through a closure and long-term stewardship plan. The objective of this screening risk assessment is to predict whether possible releases of radionuclides at the ocean floor would represent potential risks to Native Alaskans by consumption of marine subsistence species. In addition, risks were predicted for consumers of commercial catches of marine organisms. These risks were calculated beginning with estimates of possible radionuclide release at the seafloor (from a groundwater modeling study), into the seawater, through possible uptake by marine organisms, and finally possible consumption by humans. The risk assessment model has 11 elements, progressing from potential release at the seafloor through water and food chains to human intake. Data for each of these elements were systematically found and synthesized from many sources, and represent the best available knowledge. Whenever precise data were lacking

An application of cost-effectiveness analysis to restrict the damage caused by an accidental release of radioactive material to the environment

International Nuclear Information System (INIS)

Frittelli, L.; Tamburrano, A.

1980-01-01

When an accidental release of radioactive material occurs health effects in the exposed population can be mitigated by remedial actions applied to individuals or their environment. A cost-effectiveness analysis is performed by comparing the cost of remedial action with the monetary value of the collective dose avoided. (H.K.)

Nitrogen Released From Organic Residues Using 15N

International Nuclear Information System (INIS)

Galal, Y.G.M.; Gadalla, A.M.; Abdel Aziz, H.A.; Abdel Salam, A.A.; El-Degwy, S.M.A.

2008-01-01

Incubation technique was followed under laboratory condition to evaluate and determine the rate of organic residues decomposition as well as N released in media. Rice straw, soybean straw, and leuceana cutting residue were used. These materials were incubated on virgin sandy soil up to 90 days intervals. Cups with mixture of sand and organic residues were inoculated with fungi, bacteria and mixture of them. Un inoculated treatment was also included. Results showed that N released from the different organic materials was significant at 30 days of incubation. It seems that presence of Azotobacter was associated with enhanced demand on soluble N at this stage. Superiority of leucaena over the other two sources of rice straw and soybean straw occurred particularly during the 15 to 30.day period. In greenhouse experiment, the results indicated that N derived from organic materials was high and easily released from compost as mediated materials comparing to leucaena as undigested raw materials. In the same time, barley had more benefits from organic residues than lupine crop

Radioactive material releases in the nuclear fuel cycle - Recent experience and improvements

International Nuclear Information System (INIS)

Allan, C.J.; Allsop, P.J.; Anderson, R.W.; Boss, C.R.; Frost, S.E.

1997-01-01

The nuclear fuel cycle involves a wide range of activities and technologies from the mining of uranium, to the production of electricity and radioisotopes for medical and industrial applications, to the reprocessing and recycling of used fuel, to decommissioning and waste disposal. Worker exposures and releases to the environment are carefully controlled in: (a) all stages of uranium mining, refining and fuel fabrication, where occupational exposures and releases have decreased while production has increased; (b) the operation of nuclear power plants, where occupational exposures and releases have decreased as reactor vendors evolve their products and reactor operators optimize their procedures; (c) fuel reprocessing facilities in the U.K. and France, where occupational exposures and releases have decreased while the amount of fuel processed has increased; and in (d) decommissioning nuclear facilities and waste management activities. The nuclear industry's recent record of achievement in controlling its releases and ensuring the radiological protection of its employees has been excellent. It is clear that releases and occupational exposures from modem nuclear facilities of all types contribute negligibly to the radiation environment to which all biota are exposed. But the general public seems not to appreciate the low environmental impact of nuclear activities. The future of nuclear power and of other applications of nuclear technology applications in medicine, in agriculture and in industry will depend on maintaining a high standard of performance so that the public and decision makers can be assured that the industry is safe. (author)

Explosive material treatment in particular the explosive compaction of powders

International Nuclear Information System (INIS)

Pruemmer, R.

1985-01-01

The constructive use of explosives in the last decades has led to new procedures in manufacturing techniques. The most important of these are explosive forming and cladding, the latter especially for the production of compound materials. The method of explosive compaction has the highest potential for further innovation. Almost theoretical densities are achievable in the green compacts as the pressure released by detonating explosives are very high. Also, the production of new conditions of materials (metastable high pressure phases) is possible. (orig.) [de

Preparation of mesoporous silica microparticles by sol-gel/emulsion route for protein release.

Science.gov (United States)

Vlasenkova, Mariya I; Dolinina, Ekaterina S; Parfenyuk, Elena V

2018-04-06

Encapsulation of therapeutic proteins into particles from appropriate material can improve both stability and delivery of the drugs, and the obtained particles can serve as a platform for development of their new oral formulations. The main goal of this work was development of sol-gel/emulsion method for preparation of silica microcapsules capable of controlled release of encapsulated protein without loss of its native structure. For this purpose, the reported in literature direct sol-gel/W/O/W emulsion method of protein encapsulation was used with some modifications, because the original method did not allow to prepare silica microcapsules capable for protein release. The particles were synthesized using sodium silicate and tetraethoxysilane as silica precursors and different compositions of oil phase. In vitro kinetics of bovine serum albumin (BSA) release in buffer (pH 7.4) was studied by Fourier transform infrared (FTIR) and fluorescence spectrometry, respectively. Structural state of encapsulated BSA and after release was evaluated. It was found that the synthesis conditions influenced substantially the porous structure of the unloaded silica particles, release properties of the BSA-loaded silica particles and structural state of the encapsulated and released protein. The modified synthesis conditions made it possible to obtain the silica particles capable of controlled release of the protein during a week without loss of the protein native structure.

Wind field forecast for accidental release of radiative materials

International Nuclear Information System (INIS)

Kang Ling; Chen Jiayi; Cai Xuhui

2003-01-01

A meso-scale wind field forecast model was designed for emergency environmental assessment in case of accidental release of radiative materials from a nuclear power station. Actual practice of the model showed that it runs fast, has wind field prediction function, and the result given is accurate. With meteorological data collected from weather stations, and pre-treated by a wind field diagnostic model, the initial wind fields at different times were inputted as initial values and assimilation fields for the forecasting model. The model, in turn, worked out to forecast meso-scale wind field of 24 hours in a horizontal domain of 205 km x 205 km. And then, the diagnostic model was employed again with the forecasting data to obtain more detail information of disturbed wind field by local terrain in a smaller domain of 20.5 km x 20.5 km, of which the nuclear power station is at the center. Using observation data in January, April, July and October of 1996 over the area of Hangzhou Bay, wind fields in these 4 months were simulated by different assimilation time and number of the weather stations for a sensitive test. Results indicated that the method used here has increased accuracy of the forecasted wind fields. And incorporating diagnostic method with the wind field forecast model has greatly increased efficiency of the wind field forecast for the smaller domain. This model and scheme have been used in Environmental Consequence Assessment System of Nuclear Accident in Qinshan Area

Drug kinetics release from Eudragit – Tenofovir@SiOC tablets

Energy Technology Data Exchange (ETDEWEB)

Tamayo, A., E-mail: aitanath@icv.csic.es [Ceramics and Glass Institute, CSIC, Madrid (Spain); Mazo, M.A. [Ceramics and Glass Institute, CSIC, Madrid (Spain); Veiga, M.D.; Ruiz-Caro, R.; Notario-Pérez, F. [Dpt. Pharmaceutical Technology, Faculty of Pharmacy, Complutense University of Madrid, Madrid (Spain); Rubio, J. [Ceramics and Glass Institute, CSIC, Madrid (Spain)

2017-06-01

A novel drug release system has been obtained in form of tablets from Eudragit® RS and tenofovir loaded on porous silicon oxycarbide glasses (SiOC). Active carbon (AC) and mesoporous silica (MCM-41) have also been used for comparative purposes. The porous silicon oxycarbide presents a bimodal mesopore size distribution that is maintained after functionalization with amino groups. We have studied the adsorption kinetics and adsorption equilibrium when the materials are loaded with tenofovir and, in all cases, pseudo-second order kinetics and Langmuir isotherm have been revealed as the most representative models describing the kinetic and thermodynamic parameters. Besides, the tenofovir adsorption on these materials turns out to be a favorable process. In vitro release of tenofovir has been studied in simulated vaginal medium by applying different release models. Continuous tenofovir release for > 20 days has been obtained for the SiOC material functionalized with amine groups. We concluded that the drug release occurs in two steps that involve a drug diffusion step through the material pores and diffusion through the swollen polymer. The interactions between the tenofovir drug and de amine groups of the functionalized silicon oxycarbide also play an important role in the release process. - Highlights: • Kinetic and thermodinamic parameters of the adsorption of tenofovir on porous substrates have been obtained. • Sustained release of TFV for > 20 days in SVF when it is supported on SiOC and manufactured as Eudragit®RS-containing tablets. • Release described by a two-step process involving diffusion through SiOC matrix and subsequent diffusion through the polymer.

Evaluating the Effect of Nuclear Power Plant Buildings on the Atmospheric Dispersion Behavior of Released Radioactive Materials

International Nuclear Information System (INIS)

Nassar, N.N.; Tawfik, F.S.; Agamy, S.A.; Nagla, T.F.

2017-01-01

One of the most important principles in air pollution is to minimize the release of pollutants to the atmosphere, deposition on the ground and promote sufficient dilution of released pollutants within the atmosphere. Building down wash describes the effect that wind flowing over or around buildings create a cavity of reticulating winds in the are a near the buildings. These cavities cause increased vertical dispersion of plumes emitted from stacks on or near the buildings . Often it leads to elevated concentrations downwind of affected stacks. The aim of this work is to evaluate the effect of the building down wash phenomena on the atmospheric dispersion behavior of released radioactive materials from NPP. In this study, a hypothetical scenario is presented involving a point source with varying stack parameters and rectangular shaped buildings (Mille stone Nuclear Power Plant) using meteorological parameters of a chosen day. The concentrations of assumed released radionuclides, taking into consideration the building down wash effect and without are calculated using the AERMOD Model taking into consideration the effect of the type of atmospheric stability class. Also the analysis includes the model predictions for the highest 1-hour cavity concentration. The results show that the size of the cavity zone is not affected by the type of stability class, but is affected by the stack location and buildings shape. On other hand, the distance at which the plume touches the ground is affected by the type of stability class, the stack location and buildings shape. So, strategies for locating buildings need to be considered to maximize dispersion when planning for constructing several reactors and accessory buildings at a nuclear site

Release and characteristics of fungal fragments in various conditions

Energy Technology Data Exchange (ETDEWEB)

Mensah-Attipoe, Jacob [Department of Environmental Science, University of Eastern Finland, Yliopistonranta 1D, P. O. Box 1627, FI-70211 Kuopio (Finland); Saari, Sampo [Department of Physics, Tampere University of Technology, Korkeakoulunkatu 3, 33720 Tampere (Finland); Veijalainen, Anna-Maria; Pasanen, Pertti [Department of Environmental Science, University of Eastern Finland, Yliopistonranta 1D, P. O. Box 1627, FI-70211 Kuopio (Finland); Keskinen, Jorma [Department of Physics, Tampere University of Technology, Korkeakoulunkatu 3, 33720 Tampere (Finland); Leskinen, Jari T.T. [SIB Labs, University of Eastern Finland, Yliopistonranta 1E, P. O. Box 1627, FI-70211, Kuopio (Finland); Reponen, Tiina, E-mail: reponeta@ucmail.uc.edu [Department of Environmental Science, University of Eastern Finland, Yliopistonranta 1D, P. O. Box 1627, FI-70211 Kuopio (Finland); Department of Environmental Health, University of Cincinnati, P.O. Box 670056, Cincinnati, OH 45267-0056 (United States)

2016-03-15

Intact spores and submicrometer size fragments are released from moldy building materials during growth and sporulation. It is unclear whether all fragments originate from fungal growth or if small pieces of building materials are also aerosolized as a result of microbial decomposition. In addition, particles may be formed through nucleation from secondary metabolites of fungi, such as microbial volatile organic compounds (MVOCs). In this study, we used the elemental composition of particles to characterize the origin of submicrometer fragments released from materials contaminated by fungi. Particles from three fungal species (Aspergillus versicolor, Cladosporium cladosporioides and Penicillium brevicompactum), grown on agar, wood and gypsum board were aerosolized using the Fungal Spore Source Strength Tester (FSSST) at three air velocities (5, 16 and 27 m/s). Released spores (optical size, d{sub p} ≥ 0.8 μm) and fragments (d{sub p} ≤ 0.8 μm) were counted using direct-reading optical aerosol instruments. Particles were also collected on filters, and their morphology and elemental composition analyzed using scanning electron microscopes (SEMs) coupled with an Energy-Dispersive X-ray spectroscopy (EDX). Among the studied factors, air velocity resulted in the most consistent trends in the release of fungal particles. Total concentrations of both fragments and spores increased with an increase in air velocity for all species whereas fragment–spore (F/S) ratios decreased. EDX analysis showed common elements, such as C, O, Mg and Ca, for blank material samples and fungal growth. However, N and P were exclusive to the fungal growth, and therefore were used to differentiate biological fragments from non-biological ones. Our results indicated that majority of fragments contained N and P. Because we observed increased release of fragments with increased air velocities, nucleation of MVOCs was likely not a relevant process in the formation of fungal fragments. Based

Leaching from denture base materials in vitro

Energy Technology Data Exchange (ETDEWEB)

Lygre, H.; Solheim, E.; Gjerdet, N.R. [School of Medicine, Univ. of Bergen (Norway)

1995-04-01

Specimens made from denture base materials were leached in Ringer Solution and in ethanol. The specimens comprised a heat-cured product processed in two different ways and two cold-cured materials. The organic compounds leaching from the specimens to the solutions were separated, identified, and quantified by a combined gas-chromatography and gas-chromatography/mass-spectrometry technique. Additives and degradation products, possibly made by free radical reactions, were released from the denture base materials. In Ringer solution only phthalates could be quantified. In ethanol solvent, biphenyl, dibutyl phthalate, dicyclohexyl phthalate, phenyl benzoate, and phenyl salicylate were quantified. In addition, copper was found in the ethanol solvent from one of the denture base materials. The amount of leachable organic compounds varies among different materials. Processing temperature influences the initial amount of leachable compounds. 36 refs., 7 figs., 1 tab.

Malicious release of radioactive materials in urban area. Exposure of the public and emergency staff, protective measures

International Nuclear Information System (INIS)

Koch, Wolfgang; Lange, Florentin

2016-01-01

The preparedness for hypothetical radiological scenarios is part of the tasks for governmental authorities, safety and emergency organizations and the staff in case of the incident. The EURATOM guideline for radiation protection has to be implemented into national laws. According to the guidelines it is required that emergency planning has to be prepared for hypothetical radiological scenarios including terroristic or other maliciously motivated attacks using radioactive materials. The study includes assumptions on the released respirable radioactivity, restriction of the hazardous area, wind induced re-suspension of radioactive dusts and inhalation exposure, and mitigation measures.

Release of hydrogen isotopes from carbon based fusion reactor materials

International Nuclear Information System (INIS)

Vainonen-Ahlgren, E.

2000-01-01

The purpose of this study is to understand the annealing behavior of hydrogen isotopes in carbon based materials. Also, the density of the material and structural changes after thermal treatment and ion irradiation are examined. The study of hydrogen diffusion in diamondlike carbon films revealed an activation energy of 2.0 eV, while the deuterium diffusion, due to better measuring sensitivity, is found to be concentration dependent with the effective diffusion coefficient becoming smaller with decreasing deuterium concentration. To explain the experimentally observed profiles, a model according to which atomic deuterium diffuses and deuterium in clusters is immobile is developed. The concentration of immobile D was assumed to be an analytical function of the total D concentration. To describe the annealing behavior of D incorporated in diamondlike carbon films during the deposition process, a model taking into account diffusion of free D and thermal detrapping and trapping of D was developed. The difference in the analysis explains the disagreement of activation energy (1.5 ± 0.2 eV) with the value of 2,9± 0.1 eV obtained for D implanted samples earlier. The same model was applied to describe the experimental profiles in Si doped diamondlike carbon films. Si affects the retention of D in diamondlike carbon films. The amount of D depends on Si content in the co-deposited but not implanted samples. Besides, Si incorporation into carbon coating decreases to some extent the graphitization of the films and leads to formation of a structure which is stable under thermal treatment and ion irradiation. Hydrogen migration in the hydrogen and methane co-deposited films was also studied. In samples produced in methane atmosphere and annealed at different temperatures, the hydrogen concentration level decreases in the bulk, with more pronounced release at the surface region. In the case of coatings deposited by a methane ion beam, the H level also decreases with increasing

Method for forming materials

Science.gov (United States)

Tolle, Charles R [Idaho Falls, ID; Clark, Denis E [Idaho Falls, ID; Smartt, Herschel B [Idaho Falls, ID; Miller, Karen S [Idaho Falls, ID

2009-10-06

A material-forming tool and a method for forming a material are described including a shank portion; a shoulder portion that releasably engages the shank portion; a pin that releasably engages the shoulder portion, wherein the pin defines a passageway; and a source of a material coupled in material flowing relation relative to the pin and wherein the material-forming tool is utilized in methodology that includes providing a first material; providing a second material, and placing the second material into contact with the first material; and locally plastically deforming the first material with the material-forming tool so as mix the first material and second material together to form a resulting material having characteristics different from the respective first and second materials.

An evaluation of trace element release associated with acid mine drainage

International Nuclear Information System (INIS)

Sullivan, P.J.; Yelton, J.L.

1988-01-01

The determination of trace element release from geologic materials, such as oil shale and coal overburden, is important for proper solid waste management planning. The objective of this study was to determine a correlation between release using the following methods: (1) sequential selective dissolution for determining trace element residencies, (2) toxicity characteristic leaching procedure (TCLP), and (3) humidity cell weathering study simulating maximum trace element release. Two eastern oil shales were used, a New Albany shale that contains 4.6 percent pyrite, and a Chattanooga shale that contains 1.5 percent pyrite. Each shale was analyzed for elemental concentrations by soluble, adsorbed, organic, carbonate, and sulfide phases. The results of the results of the selective dissolution studies show that each trace element has a unique distribution between the various phases. Thus, it is possible to predict trace element release based on trace element residency. The TCLP results show that this method is suitable for assessing soluble trace element release but does not realistically assess potential hazards. The results of the humidity cell studies do demonstrate a more reasonable method for predicting trace element release and potential water quality hazards. The humidity cell methods, however, require months to obtain the required data with a large number of analytical measurements. When the selective dissolution data are compared to the trace element concentrations in the TCLP and humidity cell leachates, it is shown that leachate concentrations are predicted by the selective dissolution data. Therefore, selective dissolution may represent a rapid method to assess trace element release associated with acid mine drainage

Reuse of conditionally released steel; proposals and evaluation of processes for manufacturing of steel elements and processes for construction of selected scenarios - 59130

International Nuclear Information System (INIS)

Bezak, Peter; Ondra, Frantisek; Hajkova, Eva; Necas, Vladimir

2012-01-01

nuclear energy. The results of calculations confirm the possibility of reuse of conditionally released steel in compliance with input requirements. The radionuclide concentration in conditional released material can increase more than two times compared with the limit for unconditional release of materials or more than ten times in the case of additional safety or organizational measures being applied. The solution of scenarios needs to take into account the aspects of additional measures in the field of radiation protection with respect of related legislation. Results of the CONRELMAT projects provide new knowledge for future projects for reuse of conditionally released materials. (authors)

Titanium carbide-carbon porous nanocomposite materials for radioactive ion beam production: processing, sintering and isotope release properties

CERN Document Server

AUTHOR|(CDS)2081922; Stora, Thierry

2017-01-26

The Isotope Separator OnLine (ISOL) technique is used at the ISOLDE - Isotope Separator OnLine DEvice facility at CERN, to produce radioactive ion beams for physics research. At CERN protons are accelerated to 1.4 GeV and made to collide with one of two targets located at ISOLDE facility. When the protons collide with the target material, nuclear reactions produce isotopes which are thermalized in the bulk of the target material grains. During irradiation the target is kept at high temperatures (up to 2300 °C) to promote diffusion and effusion of the produced isotopes into an ion source, to produce a radioactive ion beam. Ti-foils targets are currently used at ISOLDE to deliver beams of K, Ca and Sc, however they are operated at temperatures close to their melting point which brings target degradation, through sintering and/or melting which reduces the beam intensities over time. For the past 10 years, nanostructured target materials have been developed and have shown improved release rates of the produced i...

Approach toward development of release standards for D and D cleanup

International Nuclear Information System (INIS)

Chen, S. Y.

1999-01-01

The release of materials containing residual radioactivity from a controlled environment in decontamination and decommissioning (D and D) activities has been problematic. The primary impediment to such a release is the lack of a suitable framework within which release standards can be developed. The concept of clearance for radioactive materials was recently introduced by the International Atomic Energy Agency (IAEA) (l). This concept is being evaluated by the international regulatory communities as a basis for setting standards for releasing from control solid materials containing residual radioactivity. Accordingly, both the IAEA (2) and the European Commission (EC) (3) have recently proposed clearance standards. In the US, the Nuclear Regulatory Commission (USNRC) has just begun its rule-making process on clearance. The term ''clearance'' was introduced as a regulatory process for releasing radioactive materials posing negligible risks. A trivial risk level has been determined to be a 10 -6 to 10 -7 annual risk to an exposed individual, and a population risk of no more than 0.1 for an annual practice. Under these strict constraints, exposure scenarios would be developed to estimate potential doses to affected individuals. Such scenarios may account for processing, disposal, and product end-use of materials. This paper discusses these scenarios and also describes the technical basis for deriving release levels under the suggested risk for dose constraints

10 CFR 20.2003 - Disposal by release into sanitary sewerage.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Disposal by release into sanitary sewerage. 20.2003... Disposal § 20.2003 Disposal by release into sanitary sewerage. (a) A licensee may discharge licensed material into sanitary sewerage if each of the following conditions is satisfied: (1) The material is...

A mobile dose prediction system based on artificial neural networks for NPP emergencies with radioactive material releases

Energy Technology Data Exchange (ETDEWEB)

Pereira, Claudio M.N.A.; Schirru, Roberto; Gomes, Kelcio J.; Cunha, José Luiz, E-mail: cmnap@ien.gov.br, E-mail: schirru@lmp.ufrj.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Coordenacao dos Programas de Pos-Graduacao em Engenharia (PEN/COPPE/UFRJ), Rio de Janeiro, RJ (Brazil)

2017-11-01

This work presents the approach of a mobile dose prediction system for NPP emergencies with nuclear material release. The objective is to provide extra support to field teams decisions when plant information systems are not available. However, predicting doses due to atmospheric dispersion of radionuclide generally requires execution of complex and computationally intensive physical models. In order to allow such predictions to be made by using limited computational resources such as mobile phones, it is proposed the use of artificial neural networks (ANN) previously trained (offline) with data generated by precise simulations using the NPP atmospheric dispersion system. Typical situations for each postulated accident and respective source terms, as well as a wide range of meteorological conditions have been considered. As a first step, several ANN architectures have been investigated in order to evaluate their ability for dose prediction in hypothetical scenarios in the vicinity of CNAAA Brazilian NPP, in Angra dos Reis, Brazil. As a result, good generalization and a correlation coefficient of 0.99 was achieved for a validation data set (untrained patterns). Then, selected ANNs have been coded in Java programming language to run as an Android application aimed to plot the spatial dose distribution into a map.In this paper, the general architecture of the proposed system is described; numerical results and comparisons between investigated ANN architectures are discussed; performance and limitations of running the Application into a commercial mobile phone are evaluated and possible improvements and future works are pointed. (author)

A mobile dose prediction system based on artificial neural networks for NPP emergencies with radioactive material releases

International Nuclear Information System (INIS)

Pereira, Claudio M.N.A.; Schirru, Roberto; Gomes, Kelcio J.; Cunha, José Luiz

2017-01-01

This work presents the approach of a mobile dose prediction system for NPP emergencies with nuclear material release. The objective is to provide extra support to field teams decisions when plant information systems are not available. However, predicting doses due to atmospheric dispersion of radionuclide generally requires execution of complex and computationally intensive physical models. In order to allow such predictions to be made by using limited computational resources such as mobile phones, it is proposed the use of artificial neural networks (ANN) previously trained (offline) with data generated by precise simulations using the NPP atmospheric dispersion system. Typical situations for each postulated accident and respective source terms, as well as a wide range of meteorological conditions have been considered. As a first step, several ANN architectures have been investigated in order to evaluate their ability for dose prediction in hypothetical scenarios in the vicinity of CNAAA Brazilian NPP, in Angra dos Reis, Brazil. As a result, good generalization and a correlation coefficient of 0.99 was achieved for a validation data set (untrained patterns). Then, selected ANNs have been coded in Java programming language to run as an Android application aimed to plot the spatial dose distribution into a map.In this paper, the general architecture of the proposed system is described; numerical results and comparisons between investigated ANN architectures are discussed; performance and limitations of running the Application into a commercial mobile phone are evaluated and possible improvements and future works are pointed. (author)

Controlled Release Formulation of Indomethacin Prepared With Bee ...

African Journals Online (AJOL)

Erah

2010-12-27

Dec 27, 2010 ... Results: The results show that, although the release rate of formulations F1 - F7 did not show any ... Keywords: Propolis (bee glue), Indomethacin, Controlled release, Zero order kinetics, Waxy materials ... focus of interest.

Mechanistic analysis of double-shell tank gas release

Energy Technology Data Exchange (ETDEWEB)

Allemann, R.T.; Antoniak, Z.I.; Friley, J.R.; Haines, C.E.; Liljegren, L.M.; Somasundaram, S.

1991-12-01

Pacific Northwest Laboratory (PNL) is studying possible mechanisms and fluid dynamics contributing to the periodic release of gases from the double-shell waste storage tanks at Hanford. This study is being conducted for Westinghouse Hanford Company (WHC), a contractor for the US Department of Energy (DOE). This interim report discusses the work done through November 1990. Safe management of the wastes at Hanford depends on an understanding of the chemical and physical mechanisms that take place in the waste tanks. An example of the need to understand these mechanisms is tank 101-SY. The waste in this tank is generating and periodically releasing potentially flammable gases into the tank vent system according to observations of the tank. How these gases are generated and become trapped, the causes of periodic release, and the mechanism of the release are not known in detail. In order to develop a safe mitigation strategy, possible physical mechanisms for the periodic release of flammable gases need to be understood.

ATP Release Channels

Directory of Open Access Journals (Sweden)

Akiyuki Taruno

2018-03-01

Full Text Available Adenosine triphosphate (ATP has been well established as an important extracellular ligand of autocrine signaling, intercellular communication, and neurotransmission with numerous physiological and pathophysiological roles. In addition to the classical exocytosis, non-vesicular mechanisms of cellular ATP release have been demonstrated in many cell types. Although large and negatively charged ATP molecules cannot diffuse across the lipid bilayer of the plasma membrane, conductive ATP release from the cytosol into the extracellular space is possible through ATP-permeable channels. Such channels must possess two minimum qualifications for ATP permeation: anion permeability and a large ion-conducting pore. Currently, five groups of channels are acknowledged as ATP-release channels: connexin hemichannels, pannexin 1, calcium homeostasis modulator 1 (CALHM1, volume-regulated anion channels (VRACs, also known as volume-sensitive outwardly rectifying (VSOR anion channels, and maxi-anion channels (MACs. Recently, major breakthroughs have been made in the field by molecular identification of CALHM1 as the action potential-dependent ATP-release channel in taste bud cells, LRRC8s as components of VRACs, and SLCO2A1 as a core subunit of MACs. Here, the function and physiological roles of these five groups of ATP-release channels are summarized, along with a discussion on the future implications of understanding these channels.

The atmospheric release advisory capability (ARAC): A federal emergency response capability

International Nuclear Information System (INIS)

Dickerson, M.H.; Sullivan, T.J.

1988-03-01

The Atmospheric Release Capability (ARAC) is a Department of Energy (DOE)-sponsored emergency-response service set up to provide real-time prediction of the dose levels and the extent of surface contamination resulting from a broad range of possible occurrences (accidents, spills, extortion threats involving nuclear material, reentry of nuclear-powered satellites, and atmospheric nuclear tests) that could involve the release of airborne radioactive material. During the past decade, ARAC has responded to more than 150 real-time situations, including exercises. The most notable responses include the Three Mile Island accident in Pennsylvania, the Titan II missile accident in Arkansas, the reentry of the USSR's COSMOS-954 into the atmosphere over Canada, the accidental release of uranium hexafluoride from the Sequoyah Facility accident in Oklahoma, and, most recently, the Chernobyl reactor accident in the Soviet Union. ARAC currently supports the emergency-preparedness plans at 50 Department of Defense (DOD) and DOE sites within the US and also responds to accidents that happen elsewhere. Our ARAC center serves as the focal point for data acquisition, data analysis and assessments during a response, using a computer-based communication network to acquire real-time weather data from the accident site and the surrounding region, as well as pertinent accident information. Its three-dimensional computer models for atmospheric dispersion, MATHEW and ADPIC, digest all this information and produce the predictions used in accident assessment. 9 refs., 6 figs., 1 tab

Applied exposure modeling for residual radioactivity and release criteria

International Nuclear Information System (INIS)

Lee, D.W.

1989-01-01

The protection of public health and the environment from the release of materials with residual radioactivity for recycle or disposal as wastes without radioactive contents of concern presents a formidable challenge. Existing regulatory criteria are based on technical judgment concerning detectability and simple modeling. Recently, exposure modeling methodologies have been developed to provide a more consistent level of health protection. Release criteria derived from the application of exposure modeling methodologies share the same basic elements of analysis but are developed to serve a variety of purposes. Models for the support of regulations for all applications rely on conservative interpretations of generalized conditions while models developed to show compliance incorporate specific conditions not likely to be duplicated at other sites. Research models represent yet another type of modeling which strives to simulate the actual behavior of released material. In spite of these differing purposes, exposure modeling permits the application of sound and reasoned principles of radiation protection to the release of materials with residual levels of radioactivity. Examples of the similarities and differences of these models are presented and an application to the disposal of materials with residual levels of uranium contamination is discussed. 5 refs., 2 tabs

Characteristics of microstructure and tritium release properties of different kinds of beryllium pebbles for application in tritium breeding modules

Energy Technology Data Exchange (ETDEWEB)

Kurinskiy, P., E-mail: petr.kurinskiy@kit.edu [Karlsruhe Institute of Technology, Institute for Applied Materials – Applied Materials Physics (IAM-AWP), P.O. Box 3640, Karlsruhe 76021 (Germany); Vladimirov, P.; Moeslang, A. [Karlsruhe Institute of Technology, Institute for Applied Materials – Applied Materials Physics (IAM-AWP), P.O. Box 3640, Karlsruhe 76021 (Germany); Rolli, R. [Karlsruhe Institute of Technology, Institute for Applied Materials – Materials and Biomechanics (IAM-WBM), P.O. Box 3640, Karlsruhe 76021 (Germany); Zmitko, M. [The European Joint Undertaking for ITER and the Development of Fusion Energy, c/Josep Pla, no. 2, Torres Diagonal Litoral, Edificio B3, Barcelona 08019 (Spain)

2014-10-15

Highlights: • Tritium release properties and characteristics of microstructure of beryllium pebbles having different sizes of grains were studied. • Fine-grained beryllium pebbles showed the best ability to release tritium compared to pebbles from another charges. • Be pebbles with the grain sizes exceeding 100 μm contain a great number of small pores and inclusions presumably referring to the history of material fabrication. • The sizes of grains are one of a key characteristic of microstructure which influences the parameters of tritium release. - Abstract: Beryllium pebbles with diameters of 1 mm are considered to be perspective material for the use as neutron multiplier in tritium breeding modules of fusion reactors. Up to now, the design of helium-cooled breeding blanket in ITER project foresees the use of 1 mm beryllium pebbles fabricated by NGK Insulators Ltd., Japan. It is notable that beryllium pebbles from Russian Federation and USA are also available and the possibility of their large-scale fabrication is under study. Presented work is dedicated to a study of characteristics of microstructure and parameters of tritium release of beryllium pebbles produced by Bochvar Institute, Russian Federation, and Materion Corporation, USA.

Selective adsorption and release of cationic organic dye molecules on mesoporous borosilicates

International Nuclear Information System (INIS)

Paul, Manidipa; Pal, Nabanita; Bhaumik, Asim

2012-01-01

Mesoporous materials can play a pivotal role as a host material for delivery application to a specific part of a system. In this work we explore the selective adsorption and release of cationic organic dye molecules such as safranine T (ST) and malachite green (MG) on mesoporous borosilicate materials. The mesoporous silica SBA-15 and borosilicate materials (MBS) were prepared using non-ionic surfactant Pluronic P123 as template via evaporation induced self-assembly (EISA) method. After template removal the materials show high surface areas and in some cases ordered mesopores of dimensions ca. 6–7 nm. High surface area, mesoporosity and the presence of heteroatom (boron) help this mesoporous borosilicate material to adsorb high amount of cationic dye molecules at its surface from the respective aqueous solutions. Furthermore, the mesoporous borosilicate samples containing higher percentage adsorbed dyes show excellent release of ST or MG dye in simulated body fluid (SBF) solution at physiological pH = 7.4 and temperature 310 K. The adsorption and release efficiency of mesoporous borosilicate samples are compared with reference boron-free mesoporous pure silica material to understand the nature of adsorbate–adsorbent interaction at the surfaces. - Graphical abstract: Highly ordered 2D-hexagonal mesoporous borosilicate materials have been synthesized by using Pluronic P123 as template. The materials show very good adsorption and release of organic cationic dye molecules under physiological conditions. Highlights: ► Highly ordered 2D-hexagonal mesoporous borosilicate. ► Nonionic Pluoronic P123 templated mesoporous material. ► Adsorption of organic dyes at the mesopore surface. ► Controlled release of dyes under physiological pH and temperature. ► Release of safranine T (ST) and malachite green (MG) dyes in simulated body fluids.

Effect of Drug Loading Method and Drug Physicochemical Properties on the Material and Drug Release Properties of Poly (Ethylene Oxide Hydrogels for Transdermal Delivery

Directory of Open Access Journals (Sweden)

Rachel Shet Hui Wong

2017-07-01

Full Text Available Novel poly (ethylene oxide (PEO hydrogel films were synthesized via UV cross-linking with pentaerythritol tetra-acrylate (PETRA as cross-linking agent. The purpose of this work was to develop a novel hydrogel film suitable for passive transdermal drug delivery via skin application. Hydrogels were loaded with model drugs (lidocaine hydrochloride (LID, diclofenac sodium (DIC and ibuprofen (IBU via post-loading and in situ loading methods. The effect of loading method and drug physicochemical properties on the material and drug release properties of medicated film samples were characterized using scanning electron microscopy (SEM, swelling studies, differential scanning calorimetry (DSC, fourier transform infrared spectroscopy (FT-IR, tensile testing, rheometry, and drug release studies. In situ loaded films showed better drug entrapment within the hydrogel network and also better polymer crystallinity. High drug release was observed from all studied formulations. In situ loaded LID had a plasticizing effect on PEO hydrogel, and films showed excellent mechanical properties and prolonged drug release. The drug release mechanism for the majority of medicated PEO hydrogel formulations was determined as both drug diffusion and polymer chain relaxation, which is highly desirable for controlled release formulations.

Self-Replenishing Vascularized Fouling-Release Surfaces

Energy Technology Data Exchange (ETDEWEB)

Howell, C; Vu, TL; Lin, JJ; Kolle, S; Juthani, N; Watson, E; Weaver, JC; Alvarenga, J; Aizenberg, J

2014-08-13

Inspired by the long-term effectiveness of living antifouling materials, we have developed a method for the self-replenishment of synthetic biofouling-release surfaces. These surfaces are created by either molding or directly embedding 3D vascular systems into polydimethylsiloxane (PDMS) and filling them with a silicone oil to generate a nontoxic oil-infused material. When replenished with silicone oil from an outside source, these materials are capable of self-lubrication and continuous renewal of the interfacial fouling-release layer. Under accelerated lubricant loss conditions, fully infused vascularized samples retained significantly more lubricant than equivalent nonvascularized controls. Tests of lubricant-infused PDMS in static cultures of the infectious bacteria Staphylococcus aureus and Escherichia coli as well as the green microalgae Botryococcus braunii, Chlamydomonas reinhardtii, Dunaliella sauna, and Nannochloropsis oculata showed a significant reduction in biofilm adhesion compared to PDMS and glass controls containing no lubricant. Further experiments on vascularized versus nonvascularized samples that had been subjected to accelerated lubricant evaporation conditions for up to 48 h showed significantly less biofilm adherence on the vascularized surfaces. These results demonstrate the ability of an embedded lubricant-filled vascular network to improve the longevity of fouling-release surfaces.

HOTSPOT, Field Evaluation of Radiation Release from Nuclear Accident

International Nuclear Information System (INIS)

2001-01-01

1 - Description of program or function: The HOTSPOT Health Physics codes were created to provide Health Physics personnel with a fast, field-portable calculational tool for evaluating accidents involving radioactive materials. HOTSPOT codes are a first-order approximation of the radiation effects associated with the atmospheric release of radioactive materials. HOTSPOT programs are reasonably accurate for a timely initial assessment. More importantly, HOTSPOT codes produce a consistent output for the same input assumptions and minimize the probability of errors associated with reading a graph incorrectly or scaling a universal nomogram during an emergency. Four general programs, PLUME, EXPLOSION, FIRE, and RESUSPENSION, calculate a downwind assessment following the release of radioactive material resulting from a continuous or puff release, explosive release, fuel fire, or an area contamination event. Other programs deal with the release of plutonium, uranium, and tritium to expedite an initial assessment of accidents involving nuclear weapons. Additional programs estimate the dose commitment from inhalation of any one of the radionuclides listed in the database of radionuclides, calibrate a radiation survey instrument for ground survey measurements, and screening of plutonium uptake in the lung. The HOTSPOT codes are fast, portable, easy to use, and fully documented. HOTSPOT supports color high resolution monitors and printers for concentration plots and contours. The codes have been extensively used by the DOS community since 1985. Version 8 allows users to add their own custom radionuclide library and to create custom radionuclide mixtures. It also includes wet deposition to approximate the enhanced plume depletion and ground deposition due to the effects of rain. Additional release geometry options for TRITIUM RELEASE and GENERAL PLUME were added, as well as several other enhancements and improvements. See info (f1) from the main HOTSPOT menu for additional

The Detection of Evolved Oxygen from the Rocknest Eolian Bedform Material by the Sample Analysis at Mars(SAM) instrument at the Mars Curiosity Landing Site

Science.gov (United States)

Sutter, B.; Archer, D.; Ming, D.; Eigenbrode, J. L.; Franz, H.; Glavin, D. P.; McAdam, A.; Mahaffy, P.; Stern, J.; Navarro-Gonzalex, R.;

Effect of micropatterning induced surface hydrophobicity on drug release from electrospun cellulose acetate nanofibers

Science.gov (United States)

Adepu, Shivakalyani; Gaydhane, Mrunalini K.; Kakunuri, Manohar; Sharma, Chandra S.; Khandelwal, Mudrika; Eichhorn, Stephen J.

2017-12-01

Sustained release and prevention of burst release for low half-life drugs like Diclofenac sodium is crucial to prevent drug related toxicity. Electrospun nanofibers have emerged recently as potential carrier materials for controlled and sustained drug release. Here, we present a facile method to prevent burst release by tuning the surface wettability through template assisted micropatterning of drug loaded electrospun cellulose acetate (CA) nanofibers. A known amount of drug (Diclofenac sodium) was first mixed with CA and then electrospun in the form of a nanofabric. This as-spun network was hydrophilic in nature. However, when electrospinning was carried out through non-conducting templates, viz nylon meshes with 50 and 100 μm size openings, two kinds of hydrophobic micro-patterned CA nanofabrics were produced. In vitro transdermal testing of our nanofibrous mats was carried out; these tests were able to show that it would be possible to create a patch for transdermal drug release. Further, our results show that with optimized micro-patterned dimensions, a zero order sustained drug release of up to 12 h may be achieved for the transdermal system when compared to non-patterned samples. This patterning caused a change in the surface wettability, to a hydrophobic surface, resulting in a controlled diffusion of the hydrophilic drug. Patterning assisted in controlling the initial burst release, which is a significant finding especially for low half-life drugs.

Metallic ion release from biocompatible cobalt-based alloy

Directory of Open Access Journals (Sweden)

Dimić Ivana D.

2014-01-01

Full Text Available Metallic biomaterials, which are mainly used for the damaged hard tissue replacements, are materials with high strength, excellent toughness and good wear resistance. The disadvantages of metals as implant materials are their susceptibility to corrosion, the elastic modulus mismatch between metals and human hard tissues, relatively high density and metallic ion release which can cause serious health problems. The aim of this study was to examine metallic ion release from Co-Cr-Mo alloy in artificial saliva. In that purpose, alloy samples were immersed into artificial saliva with different pH values (4.0, 5.5 and 7.5. After a certain immersion period (1, 3 and 6 weeks the concentrations of released ions were determined using Inductively Coupled Plasma - Mass Spectrophotometer (ICP-MS. The research findings were used in order to define the dependence between the concentration of released metallic ions, artificial saliva pH values and immersion time. The determined released metallic ions concentrations were compared with literature data in order to describe and better understand the phenomenon of metallic ion release from the biocompatible cobalt-based alloy. [Projekat Ministarstva nauke Republike Srbije, br. III 46010 i br. ON 174004

Massive radiological releases profoundly differ from controlled releases

International Nuclear Information System (INIS)

Pascucci-Cahen, Ludivine; Patrick, Momal

2012-11-01

Preparing for a nuclear accident implies understanding potential consequences. While many specialized experts have been working on different particular aspects, surprisingly little effort has been dedicated to establishing the big picture and providing a global and balanced image of all major consequences. IRSN has been working on the cost of nuclear accidents, an exercise which must strive to be as comprehensive as possible since any omission obviously underestimates the cost. It therefore provides (ideally) an estimate of all cost components, thus revealing the structure of accident costs, and hence sketching a global picture. On a French PWR, it appears that controlled releases would cause an 'economical' accident with limited radiological consequences when compared to other costs; in contrast, massive releases would trigger a major crisis with strong radiological consequences. The two types of crises would confront managers with different types of challenges. (authors)

Slow release coating remedy for nitrogen loss from conventional urea: a review.

Science.gov (United States)

Naz, Muhammad Yasin; Sulaiman, Shaharin Anwar

2016-03-10

Developing countries are consuming major part of the global urea production with an anticipated nitrogen use efficiency of 20 to 35%. The release of excess nitrogen in the soil is not only detrimental to the environment but also lessens the efficiency of the conventional urea. The urea performance can be enhanced by encapsulating it with slow release coating materials and synchronizing the nutrients' release with the plant up-taking. However, the present cost of most of the coated fertilizers is considerably higher than the conventional fertilizers. The high cost factor prevents their widespread use in mainstream agriculture. This paper documents a review of literature related to the global urea market, issues pertaining to the conventional urea use, natural and synthetic materials for slow release urea and fluidized bed spray coating process. The aim of the current review is to develop technical understanding of the conventional and non-conventional coating materials and associated spray coating mechanism for slow release urea production. The study also investigated the potential of starch as the coating material in relation to the coatings tested previously for controlled release fertilizers. Copyright © 2016 Elsevier B.V. All rights reserved.

Transporting radioactive materials and possible radiological consequences from accidents as might be seen by medical institutions

International Nuclear Information System (INIS)

Jefferson, R.M.

1990-01-01

This paper discusses how medical personnel faced with treating victims of an accident involving radioactive material should be suspicious concerning possible radiological involvement. At the same time, they should be careful to obtain the necessary information in order to make a rational decision as to the likelihood of such involvement. Having made that decision, it is entirely possible then to approach the problem from a medical standpoint in such a way as to determine the extent of radiological involvement and to apply proper medical treatment consistent with that exposure

Comparative Evaluation of Fluoride Releasing Ability of Various Restorative Materials after the Application of Surface Coating Agents - An In-vitro Study.

Science.gov (United States)

Kishore, Gvs; Sai-Sankar, A J; Pratap-Gowd, Mjs; Sridhar, M; Pranitha, Kakarla; Sai-Krishna, V S

2016-12-01

Fluoride plays a key role in prevention of dental caries and is also an essential element for oral health promotion both in children and adults. The aim of the present study was to evaluate the effect of surface coating (petroleum jelly, G-Coat Plus) on the fluoride releasing property of conventional Glass Ionomer Cement (GIC) and Zirconomer. A total of 30 disk shaped brass mold specimens (6±0.1mm in diameter and 2±0.1mm thickness) for each test group were fabricated with conventional GIC (Group A) and Zirconomer (Group B). These test groups were further divided into three subgroups of 10 each. The unprotected specimens act as control (Group A1 and B1), G-Coat Plus specimens as (Group A2 and B2) and for the remaining specimens petroleum jelly was applied (Group A3 and B3). Fluoride ion concentration was measured with a combination of fluoride ion specific electrode and ion analyzer for every 24 hours for 15 days. The data was statistically analyzed using Kruskal Wallis and Mann-Whitney U test. The Group B released significantly more fluoride than Group A. Among all the subgroups the greatest amount of fluoride was released from Group B1, in the first 24 hours followed by A1 and B2. The least was observed on 15 th day with Group B3 and A3. Both the tested materials (GIC and Zirconomer) used in the study exhibited fluoride release whether protected or unprotected with surface coating. Though there was a difference between the groups, the pattern of fluoride release was similar and continuous throughout the study period i.e., first the initial burst followed by sustained release. The results revealed Zirconomer released more fluoride and is comparable to conventional GIC.

Creep rupture behavior of polypropylene suture material and its applications as a time-release mechanism

International Nuclear Information System (INIS)

Kusy, R.P.; Whitley, J.Q.

1983-01-01

The controlled failure of polypropylene (PP) sutures is studied via creep rupture tests. From plots of log time (tB) vs. stress (sigma), linear relationships are generated over the failure times of 1-1000 h. Results show that as a function of stress, the time dependence varies with irradiation dose (15, 20, 25, and 50 Mrad), irradiation atmosphere (air and vacuum), suture diameter (7-0, 6-0, 5-0, and 4-0), and test temperature (26 and 37 degrees C). For a given stress, the time to failure is least for the greatest dose in the presence of air and at the highest temperature. When suture loops are wrapped around a small wire sheave, however, failure occurs in the largest suture as much as two decades sooner than the smallest suture studied. Within the limitations stated herein, they are independent of test method, loop diameter, aging, and humidity. Consequently, after irradiation in vacuum and postirradiation heat treatment, the processed material may be stored at room temperature for at least 1 month. Such materials are advocated when the time release of a dental or medical device is required, for example, in the self-activating cleft palate appliance

Release of engineered nanomaterials from polymer nanocomposites: the effect of matrix degradation.

Science.gov (United States)

Duncan, Timothy V

2015-01-14

Polymer nanocomposites-polymer-based materials that incorporate filler elements possessing at least one dimension in the nanometer range-are increasingly being developed for commercial applications ranging from building infrastructure to food packaging to biomedical devices and implants. Despite a wide range of intended applications, it is also important to understand the potential for exposure to these nanofillers, which could be released during routine use or abuse of these materials so that it can be determined whether they pose a risk to human health or the environment. This article is the second of a pair that review what is known about the release of engineered nanomaterials (ENMs) from polymer nanocomposites. Two roughly separate ENM release paradigms are considered in this series: the release of ENMs via passive diffusion, desorption, and dissolution into external liquid media and the release of ENMs assisted by matrix degradation. The present article is focused primarily on the second paradigm and includes a thorough, critical review of the associated body of peer-reviewed literature on ENM release by matrix degradation mechanisms, including photodegradation, thermal decomposition, mechanical wear, and hydrolysis. These release mechanisms may be especially relevant to nanocomposites that are likely to be subjected to weathering, including construction and infrastructural materials, sporting equipment, and materials that might potentially end up in landfills. This review pays particular attention to studies that shed light on specific release mechanisms and synergistic mechanistic relationships. The review concludes with a short section on knowledge gaps and future research needs.

Gas storage materials, including hydrogen storage materials

Science.gov (United States)

Mohtadi, Rana F; Wicks, George G; Heung, Leung K; Nakamura, Kenji

2013-02-19

A material for the storage and release of gases comprises a plurality of hollow elements, each hollow element comprising a porous wall enclosing an interior cavity, the interior cavity including structures of a solid-state storage material. In particular examples, the storage material is a hydrogen storage material such as a solid state hydride. An improved method for forming such materials includes the solution diffusion of a storage material solution through a porous wall of a hollow element into an interior cavity.

Challenges in materials science and possibilities in 3D and 4D characterization techniques

International Nuclear Information System (INIS)

Hansen, N.; Juul Jensen, D.; Nielsen, S.F.; Poulsen, H.F.; Ralph, B.

2010-01-01

Present days see a global effort to develop new and advanced materials and as an integral part of this endeavor a range of new characterization techniques are becoming available, which have led to significant breakthroughs in materials science and engineering. Within this broad scientific field the symposium focus on metals and on 3D and 4D characterization techniques using x-rays, neutrons and electrons. These techniques now allow characterization on a finer and finer scale and open up for analysis of dynamic behavior by real time in-situ investigations. This means that techniques are now available by which key challenges in materials science can be addressed. The combination of techniques and challenges has been the guide for contributions to this year symposium and these proceedings shows the successful result. The collection of papers demonstrates the many new possibilities in 3D and 4D characterization techniques and also the applications of these techniques in the studies of important materials science and engineering themes, for example: evolution in structure and properties under thermal and mechanical loading and during annealing, phase transformations and fracture/damage. The proceedings contain the 14 key note and 34 contributed presentations of the symposium, covering the above key themes. (LN)

Analysis of metal ion release from biomedical implants

Directory of Open Access Journals (Sweden)

Ivana Dimić

2013-06-01

Full Text Available Metallic biomaterials are commonly used for fixation or replacement of damaged bones in the human body due to their good combination of mechanical properties. The disadvantage of metals as implant materials is their susceptibility to corrosion and metal ion release, which can cause serious health problems. In certain concentrations metals and metal ions are toxic and their presence can cause diverse inflammatory reactions, genetic mutations or even cancer. In this paper, different approaches to metal ion release examination, from biometallic materials sample preparation to research results interpretation, will be presented. An overview of the analytical techniques, used for determination of the type and concentration of released ions from implants in simulated biofluids, is also given in the paper.

Early and late histamine release induced by albumin, hetastarch and polygeline: some unexpected findings.

Science.gov (United States)

Celik, I; Duda, D; Stinner, B; Kimura, K; Gajek, H; Lorenz, W

2003-10-01

The perioperative use of colloidal plasma substitutes is still under discussion. We therefore conducted a prospective randomised study with three commonly used plasma substitutes to examine their histamine releasing effects in 21 volunteers. MATERIAL OR SUBJETS: 21 male volunteers were enrolled in this prospective, randomised, controlled clinical study. Endpoints were the incidence of early and late histamine release and the time course of the release kinetics. Normovolemic hemodilution technique was used with hydroxyethyl starch (n = 6), human albumin (n = 6) and polygeline (n = 9). Measurement and observation period was 240 min after the start of the plasma substitute infusion. Heart rate, blood pressure, SaO(2), clinical symptoms/signs and plasma histamine were measured during the observation period. The incidence of histamine release over the whole observation period in all three groups was 100%. Histamine release occurred frequently in all three groups until 30 min (50%-78%) and up to 240 min (late release reaction: 67%-83%) after the start of infusion. Surprisingly even hydroxyethyl starch, which is regarded as a generally safe and effective plasma substitute, caused high incidences of late histamine release (67%). Histamine release is a well known side effect of polygeline and - to a lesser extent - also of albumin, but was a novel finding for hydroxyethyl starch. We demonstrated for the first time histamine releasing effects of hydroxyethyl starch over a long period of time after administration. This perioperatively and for intensive care possibly relevant finding should make clinicians aware of late side effects not yet connected with the clinical use of these colloidal plasma substitutes.

Feasibility of using microencapsulated phase change materials as filler for improving low temperature performance of rubber sealing materials.

Science.gov (United States)

Tiwari, Avinash; Shubin, Sergey N; Alcock, Ben; Freidin, Alexander B; Thorkildsen, Brede; Echtermeyer, Andreas T

2017-11-01

The feasibility of a novel composite rubber sealing material to improve sealing under transient cooling (in a so-called blowdown scenario) is investigated here. A composite of hydrogenated nitrile butadiene rubber (HNBR) filled with Micro Encapsulated Phase Change Materials (MEPCM) is described. The fillers contain phase change materials that release heat during the phase transformation from liquid to solid while cooling. This exotherm locally heats the rubber and may improve the function of the seal during a blowdown event. A representative HNBR-MEPCM composite was made and the critical thermal and mechanical properties were obtained by simulating the temperature distribution during a blowdown event. Simulations predict that the MEPCM composites can delay the temperature decrease in a region of the seal during the transient blowdown. A sensitivity analysis of material properties is also presented which highlights possible avenues of improvement of the MEPCMs for sealing applications.

Idaho National Engineering Laboratory response to the December 13, 1991, Congressional inquiry on offsite release of hazardous and solid waste containing radioactive materials from Department of Energy facilities

International Nuclear Information System (INIS)

Shapiro, C.; Garcia, K.M.; McMurtrey, C.D.; Williams, K.L.; Jordan, P.J.

1992-05-01

This report is a response to the December 13, 1991, Congressional inquiry that requested information on all hazardous and solid waste containing radioactive materials sent from Department of Energy facilities to offsite facilities for treatment or disposal since January 1, 1981. This response is for the Idaho National Engineering Laboratory. Other Department of Energy laboratories are preparing responses for their respective operations. The request includes ten questions, which the report divides into three parts, each responding to a related group of questions. Part 1 answers Questions 5, 6, and 7, which call for a description of Department of Energy and contractor documentation governing the release of waste containing radioactive materials to offsite facilities. ''Offsite'' is defined as non-Department of Energy and non-Department of Defense facilities, such as commercial facilities. Also requested is a description of the review process for relevant release criteria and a list of afl Department of Energy and contractor documents concerning release criteria as of January 1, 1981. Part 2 answers Questions 4, 8, and 9, which call for information about actual releases of waste containing radioactive materials to offsite facilities from 1981 to the present, including radiation levels and pertinent documentation. Part 3 answers Question 10, which requests a description of the process for selecting offsite facilities for treatment or disposal of waste from Department of Energy facilities. In accordance with instructions from the Department of Energy, the report does not address Questions 1, 2, and 3

In situ depot comprising phase-change materials that can sustainably release a gasotransmitter H2S to treat diabetic wounds.

Science.gov (United States)

Lin, Wei-Chih; Huang, Chieh-Cheng; Lin, Shu-Jyuan; Li, Meng-Ju; Chang, Yen; Lin, Yu-Jung; Wan, Wei-Lin; Shih, Po-Chien; Sung, Hsing-Wen

2017-11-01

Patients with diabetes mellitus are prone to develop refractory wounds. They exhibit reduced synthesis and levels of circulating hydrogen sulfide (H 2 S), which is an ephemeral gaseous molecule. Physiologically, H 2 S is an endogenous gasotransmitter with multiple biological functions. An emulsion method is utilized to prepare a microparticle system that comprises phase-change materials with a nearly constant temperature of phase transitions to encapsulate sodium hydrosulfide (NaHS), a highly water-labile H 2 S donor. An emulsion technique that can minimize the loss of water-labile active compounds during emulsification must be developed. The as-prepared microparticles (NaHS@MPs) provide an in situ depot for the sustained release of exogenous H 2 S under physiological conditions. The sustained release of H 2 S promotes several cell behaviors, including epidermal/endothelial cell proliferation and migration, as well as angiogenesis, by extending the activation of cellular ERK1/2 and p38, accelerating the healing of full-thickness wounds in diabetic mice. These experimental results reveal the strong potential of NaHS@MPs for the sustained release of H 2 S for the treatment of diabetic wounds. Copyright © 2017 Elsevier Ltd. All rights reserved.

Ascorbyl Tetraisopalmitate Inclusion into Υ-Cyclodextrin and Mesoporous SBA-15: Preparation, Characterization and In Vitro Release Study

Directory of Open Access Journals (Sweden)

Maria Bastianini

2017-07-01

Full Text Available Ascorbic acid or vitamin C is a strong antioxidant widely used in cosmetic and food fields. This vitamin is very unstable and rapidly undergoes degradation. In order to solve this problem and to obtain a stable ascorbic acid, Nikkol Group has developed ascorbyltetraisopalmitate (VC-IP. This raw material is an oil phase, already well-known and employed in the cosmetic market. The objective of this study is to obtain VC-IP in micro-powder form, in order to produce a new raw material that is easily dispersible in oil and water phases and useful for make-up and color cosmetic applications. Various types of drug carriers were studied and considered in order to support VC-IP and obtain the conversion in powder. Υ-cyclodextrin and mesoporous silica SBA-15 were chosen as the best candidates. A white powder of supported VC-IP was obtained with each carrier (VC-IP@cyclodextrin, VC-IP@SBA-15. The systems underwent physicochemical characterization and in vitro release tests were carried out. Based on the conducted study, it can be concluded that by supporting VC-IP on Υ-cyclodextrin and SBA-15, it is feasible to obtain a new raw material in powder form. The two carriers possess different release profiles, adding the possibility to finely tune the release of the active component in smart formulations.

The management routes for materials produced by the dismantling of the BR3-PWR reactor

International Nuclear Information System (INIS)

Klein, M.; Demeulemeester, Y.; Ponnet, M.; Emond, M.; Emond, O.; Dadoumont, J.; Massaut, V.

2000-01-01

The dismantling of the BR3 reactor produces quite large masses of contaminated materials, mainly metals or concrete. The main management routes are: conditioning of the radioactive wastes and disposal, recycling of radioactive materials in the nuclear sector and the recycling of free released materials in the industrial sector or their evacuation as industrial waste. The conditioning of the radioactive wastes is essentially performed in the installations of Belgoprocess and must follow the specifications imposed by the national radwaste management agency ONDRAF/NIRAS. The conditioning of the pieces produced during the cutting of the reactor pressure vessel is given as example. The recycling of radioactive materials in the nuclear sector is possible for metals and for concrete. For metals, SCK.CEN has an agreement with a nuclear foundry which reuses these materials for the fabrication of shieldings. For concrete, an R and D programme is going on with the objective to demonstrate the possible reuse of baryte concrete as raw materials for the production of mortar used in the conditioning of radioactive wastes. The free release of radioactive materials and their reuse or evacuation as radioactive wastes requires the strict respect of procedures and the use of low level measurement techniques. Various decontamination techniques are used at SCK.CEN to reach this objective. For the metals, we use mainly simple washing, abrasive decontamination and hard chemical decontamination. For concrete, we use mainly scabbling or shaving techniques. (authors)

Tritium loading in ITER plasma-facing surfaces and its release under accident conditions

International Nuclear Information System (INIS)

Longhurst, G.R.; Anderl, R.A.; Pawelko, R.J.

1996-01-01

Plasma-facing surfaces of the International Thermonuclear Experimental Reactor (ITER) will take up tritium from the plasma. These surfaces will probably consist of matures of Be, C, and possibly W together with other impurities. Recent experimental results have suggested mechanisms, not previously considered in analyses, by which tritium and other hydrogen isotopes are retained in Be. This warrants revised modeling and estimation of the amount of tritium that will be deposited in ITER beryllium plasma-facing surfaces and the rates at which it can be released under postulated accident scenarios. In this paper we describe improvements in modeling and experiments planned at the Idaho National Engineering Laboratory (INEL) to investigate the tritium uptake and thermal release behavior for mixed plasma- facing materials. TMAP4 calculations were made using recent data to estimate first-wall tritium inventories in ITER. 16 refs., 1 fig

Halite as a Methane Sequestration Host: A Possible Explanation for Periodic Methane Release on Mars, and a Surface-accessible Source of Ancient Martian Carbon

Science.gov (United States)

Fries, M. D.; Steele, Andrew; Hynek, B. M.

2015-01-01

We present the hypothesis that halite may play a role in methane sequestration on the martian surface. In terrestrial examples, halite deposits sequester large volumes of methane and chloromethane. Also, examples of chloromethane-bearing, approximately 4.5 Ga old halite from the Monahans meteorite show that this system is very stable unless the halite is damaged. On Mars, methane may be generated from carbonaceous material trapped in ancient halite deposits and sequestered. The methane may be released by damaging its halite host; either by aqueous alteration, aeolian abrasion, heating, or impact shock. Such a scenario may help to explain the appearance of short-lived releases of methane on the martian surface. The methane may be of either biogenic or abiogenic origin. If this scenario plays a significant role on Mars, then martian halite deposits may contain samples of organic compounds dating to the ancient desiccation of the planet, accessible at the surface for future sample return missions.

Relative Release-to-Birth Indicators for Investigating TRISO Fuel Fission Gas Release Models

International Nuclear Information System (INIS)

Harp, Jason M.; Hawari, Ayman I.

2008-01-01

TRISO microsphere fuel is the fundamental fuel unit for Very High Temperature Reactors (VHTR). A single TRISO particle consists of an inner kernel of uranium dioxide or uranium oxycarbide surrounded by layers of pyrolytic carbon and silicon carbide. If the silicon carbide layer fails, fission products, especially the noble fission gases Kr and Xe, will begin to escape the failed particle. The release of fission gas is usually quantified by measuring the ratio of the released activity (R) to the original birth activity (B), which is designated as the R/B ratio. In this work, relative Release-to-Birth indicators (I) are proposed as a technique for interpreting the results of TRISO irradiation experiments. By implementing a relative metric, it is possible to reduce the sensitivity of the indicators to instrumental uncertainties and variations in experimental conditions. As an example, relative R/B indicators are applied to the interpretation of representative data from the Advanced Gas Reactor-1 TRISO fuel experiment that is currently taking place at the Advanced Test Reactor of Idaho National Laboratory. It is shown that the comparison of measured to predicted relative R/B indicators (I) gives insight into the physics of release and helps validate release models. Different trends displayed by the indicators are related to the mechanisms of fission gas release such as diffusion and recoil. The current analysis shows evidence for separate diffusion coefficients for Kr and Xe and supports the need to account for recoil release. (authors)

InAs migration on released, wrinkled InGaAs membranes used as virtual substrate

International Nuclear Information System (INIS)

Filipe Covre da Silva, S; Lanzoni, E M; De Araujo Barboza, V; Deneke, Ch; Malachias, A; Kiravittaya, S

2014-01-01

Partly released, relaxed and wrinkled InGaAs membranes are used as virtual substrates for overgrowth with InAs. Such samples exhibit different lattice parameters for the unreleased epitaxial parts, the released flat, back-bond areas and the released wrinkled areas. A large InAs migration towards the released membrane is observed with a material accumulation on top of the freestanding wrinkles during overgrowth. A semi-quantitative analysis of the misfit strain shows that the material migrates to the areas of the sample with the lowest misfit strain, which we consider as the areas of the lowest chemical potential of the surface. Material migration is also observed for the edge-supported, freestanding InGaAs membranes found on these samples. Our results show that the released, wrinkled nanomembranes offer a growth template for InAs deposition that fundamentally changes the migration behavior of the deposited material on the growth surface. (paper)

Possibility of using sources of vacuum ultraviolet irradiation to solve problems of space material science

Science.gov (United States)

Verkhoutseva, E. T.; Yaremenko, E. I.

1974-01-01

An urgent problem in space materials science is simulating the interaction of vacuum ultraviolet (VUV) of solar emission with solids in space conditions, that is, producing a light source with a distribution that approximates the distribution of solar energy. Information is presented on the distribution of the energy flux of VUV of solar radiation. Requirements that must be satisfied by the VUV source used for space materials science are formulated, and a critical evaluation is given of the possibilities of using existing sources for space materials science. From this evaluation it was established that none of the sources of VUV satisfies the specific requirements imposed on the simulator of solar radiation. A solution to the problem was found to be in the development of a new type of source based on exciting a supersonic gas jet flowing into vacuum with a sense electron beam. A description of this gas-jet source, along with its spectral and operation characteristics, is presented.

19 CFR 142.50 - Line Release data base corrections or changes.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Line Release data base corrections or changes. 142...; DEPARTMENT OF THE TREASURY (CONTINUED) ENTRY PROCESS Line Release § 142.50 Line Release data base corrections... numbers or bond information on a Line Release Data Loading Sheet as soon as possible. Notification shall...

Optimization of a phase change material wallboard for building use

International Nuclear Information System (INIS)

Kuznik, Frederic; Virgone, Joseph; Noel, Jean

2008-01-01

In construction, the use of phase change materials (PCM) allows the storage/release of energy from the solar radiation and/or internal loads. The application of such materials for lightweight construction (e.g., a wood house) makes it possible to improve thermal comfort and reduce energy consumption. A wallboard composed of a new PCM material is investigated in this paper to enhance the thermal behavior of a lightweight internal partition wall. The paper focuses on the optimization of phase change material thickness. The in-house software CODYMUR is used to optimize the PCM wallboard by the means of numerical simulations. The results show that an optimal PCM thickness exists. The optimal PCM thickness value is then calculated for use in construction

Optimization of a phase change material wallboard for building use

Energy Technology Data Exchange (ETDEWEB)

Kuznik, Frederic; Virgone, Joseph [Thermal Sciences Center of Lyon, CNRS, UMR 5008, INSA de Lyon, Universite Lyon 1, Bat Freyssinet, 40 Rue des Arts, 69621 Villeurbanne Cedex (France); Noel, Jean [Free-lance Scientific Software Developer, 15 Place Carnot, 69002 Lyon (France)

2008-08-15

In construction, the use of phase change materials (PCM) allows the storage/release of energy from the solar radiation and/or internal loads. The application of such materials for lightweight construction (e.g., a wood house) makes it possible to improve thermal comfort and reduce energy consumption. A wallboard composed of a new PCM material is investigated in this paper to enhance the thermal behavior of a lightweight internal partition wall. The paper focuses on the optimization of phase change material thickness. The in-house software CODYMUR is used to optimize the PCM wallboard by the means of numerical simulations. The results show that an optimal PCM thickness exists. The optimal PCM thickness value is then calculated for use in construction. (author)

Temperature-responsive PLLA/PNIPAM nanofibers for switchable release

Energy Technology Data Exchange (ETDEWEB)

Elashnikov, Roman; Slepička, Petr [Department of Solid State Engineering, University of Chemistry and Technology, Prague 166 28 (Czech Republic); Rimpelova, Silvie; Ulbrich, Pavel [Department of Biochemistry and Microbiology, University of Chemistry and Technology, 16628 Prague (Czech Republic); Švorčík, Vaclav [Department of Solid State Engineering, University of Chemistry and Technology, Prague 166 28 (Czech Republic); Lyutakov, Oleksiy, E-mail: lyutakoo@vscht.cz [Department of Solid State Engineering, University of Chemistry and Technology, Prague 166 28 (Czech Republic)

2017-03-01

Smart antimicrobial materials with on-demand drug release are highly desired for biomedical applications. Herein, we report about temperature-responsive poly(N-isopropylacrylamide) (PNIPAM) nanospheres doped with crystal violet (CV) and incorporated into the poly-L-lactide (PLLA) nanofibers. The nanofibers were prepared by electrospinning, using different initial polymers ratios. The morphology of the nanofibers and polymers distribution in the nanofibers were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The interaction between PNIPAM and PLLA in the nanofibers was studied by Fourier transform infrared spectroscopy (FTIR) and its effect on the PNIPAM phase transition was also investigated. It was shown that by the changing of the environmental temperature across the lower critical solution temperature (LCST) of PNIPAM, the switchable wettability and controlled CV release can be achieved. The temperature-dependent release kinetics of CV from polymer nanofibers was investigated by ultraviolet-visible spectroscopy (UV–Vis). The temperature-responsive release of antibacterial CV was also tested for triggering of antibacterial activity, which was examined on Staphylococcus epidermidis (S. epidermidis) and Escherichia coli (E. coli). Thus, the proposed material is promising value for controllable drug-release.

ARANO - a computer program for the assessment of radiological consequences of atmospheric radioactive releases

International Nuclear Information System (INIS)

Savolainen, I.; Vuori, S.

1980-09-01

A short description of the calculation possibilities, methods and of the structure of the computer code system ARANO is given, in addition to the input quide. The code can be employed in the calculation of environmental radiological consequences caused by radioactive materials released to atmosphere. Results can be individual doses for different organs at given distances from the release point, collective doses, numbers of persons exceeding given dose limits, numbers of casualties, areas polluted by deposited activity and losses of investments or production due to radioactive contamination. Both a case with a single release and atmospheric dispersion situation and a group of radioactive release and dispersions with discrete probability distributions can be considered. If the radioactive releases or the dispersion conditions are described by probability distributions, the program assesses the magnitudes of the specified effects in all combinations of the release and dispersion situations and then calculates the expectation values and the cumulative probability distributions of the effects. The vertical mixing in the atmosphere is described with a Ksub(Z)-model. In the lateral direction the plume is assumed to be Gaussian, and the release duration can be taken into account in the σsub(y)-values. External gamma dose from the release plume is calculated on the basis of a data file which has been created by 3-dimensional integration. Dose due to inhalation and due to gamma radiation from the contaminated ground are calculated by using appropriate dose conversion factors, which are collected into two mutually alternative block data subprograms. (author)

Physical protection system of nuclear material in the Federal Republic of Germany

International Nuclear Information System (INIS)

Bueker, H.; Jungclaus, D.; von Eyss, H.J.; von Osten, W.

1980-01-01

The objective of physical protection, its statutory and other bases as well as the parties involved in the licensing process are described. The facilities are grouped in categories reflecting their hazard potentials: the possibility of a theft of nuclear fuels in an approach similar to INFCIRC 225 and, in addition, the possibility of a release of radioactive materials. Physical protection follows the concept of detection, alert of police force, delay, prevention of the act by police force. The schematic layout of a Category I facility is presented

Novel meloxicam releasing electrospun polymer/ceramic reinforced biodegradable membranes for periodontal regeneration applications

Energy Technology Data Exchange (ETDEWEB)

Yar, Muhammad, E-mail: drmyar@ciitlahore.edu.pk [Interdisciplinary Research Center in Biomedical Materials, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan); Farooq, Ariba [Interdisciplinary Research Center in Biomedical Materials, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan); Department of Chemistry, The Islamia University of Bahawalpur, Bahawalpur 63100 (Pakistan); Shahzadi, Lubna; Khan, Abdul Samad [Interdisciplinary Research Center in Biomedical Materials, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan); Mahmood, Nasir [Department of Allied Health Sciences and Chemical Pathology, Department of Human Genetics and Molecular Biology, University of Health Sciences, Lahore (Pakistan); Rauf, Abdul [Department of Chemistry, The Islamia University of Bahawalpur, Bahawalpur 63100 (Pakistan); Chaudhry, Aqif Anwar [Interdisciplinary Research Center in Biomedical Materials, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan); Rehman, Ihtesham ur [Interdisciplinary Research Center in Biomedical Materials, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan); Department of Materials Science and Engineering, The Kroto Research Institute, The University of Sheffield, North Campus, Broad Lane, Sheffield S3 7HQ (United Kingdom)

2016-07-01

Periodontal disease is associated with the destruction of periodontal tissues, along with other disorders/problems including inflammation of tissues and severe pain. This paper reports the synthesis of meloxicam (MX) immobilized biodegradable chitosan (CS)/poly(vinyl alcohol) (PVA)/hydroxyapatite (HA) based electrospun (e-spun) fibers and films. Electrospinning was employed to produce drug loaded fibrous mats, whereas films were generated by solvent casting method. In-vitro drug release from materials containing varying concentrations of MX revealed that the scaffolds containing higher amount of drug showed comparatively faster release. During initial first few hours fast release was noted from membranes and films; however after around 5 h sustained release was achieved. The hydrogels showed good swelling property, which is highly desired for soft tissue engineered implants. To investigate the biocompatibility of our synthesized materials, VERO cells (epithelial cells) were selected and cell culture results showed that these all materials were non-cytotoxic and also these cells were very well proliferated on these synthesized scaffolds. These properties along with the anti-inflammatory potential of our fabricated materials suggest their effective utilization in periodontital treatments. - Highlights: • NSAIDs releasing scaffolds for periodontal regeneration applications • Meloxicam immobilized biodegradable nanocomposite electrospun membranes and films • Good swelling properties • Controlled drug release • VERO cells were very well proliferated and synthesized materials were found to be non-cytotoxic.

Novel meloxicam releasing electrospun polymer/ceramic reinforced biodegradable membranes for periodontal regeneration applications

International Nuclear Information System (INIS)

Yar, Muhammad; Farooq, Ariba; Shahzadi, Lubna; Khan, Abdul Samad; Mahmood, Nasir; Rauf, Abdul; Chaudhry, Aqif Anwar; Rehman, Ihtesham ur

2016-01-01

Periodontal disease is associated with the destruction of periodontal tissues, along with other disorders/problems including inflammation of tissues and severe pain. This paper reports the synthesis of meloxicam (MX) immobilized biodegradable chitosan (CS)/poly(vinyl alcohol) (PVA)/hydroxyapatite (HA) based electrospun (e-spun) fibers and films. Electrospinning was employed to produce drug loaded fibrous mats, whereas films were generated by solvent casting method. In-vitro drug release from materials containing varying concentrations of MX revealed that the scaffolds containing higher amount of drug showed comparatively faster release. During initial first few hours fast release was noted from membranes and films; however after around 5 h sustained release was achieved. The hydrogels showed good swelling property, which is highly desired for soft tissue engineered implants. To investigate the biocompatibility of our synthesized materials, VERO cells (epithelial cells) were selected and cell culture results showed that these all materials were non-cytotoxic and also these cells were very well proliferated on these synthesized scaffolds. These properties along with the anti-inflammatory potential of our fabricated materials suggest their effective utilization in periodontital treatments. - Highlights: • NSAIDs releasing scaffolds for periodontal regeneration applications • Meloxicam immobilized biodegradable nanocomposite electrospun membranes and films • Good swelling properties • Controlled drug release • VERO cells were very well proliferated and synthesized materials were found to be non-cytotoxic.

A Self-Peeling Vat for Improved Release Capabilities During DLP Materials Processing

DEFF Research Database (Denmark)

Pedersen, David Bue; Zhang, Yang; Nielsen, Jakob Skov

2016-01-01

for an eased release of the manufactured part from the vat by means of a flexible membrane system. A membrane of fluorinated ethylene polymer will through elastic deformation automatically peel off the part as the part is lifted during layer changes. Peeling has been qualified by means of a truncated inverted...... cone as test geometry. As the cross-sectional diameter of the cone increase throughout the build-job, the geometry will release from the glass based build platform at the point where the peeling force exceed the adhesion force between platform and part. At failure point the lateral surface area...... of the top and bottom of the truncated cone is used as a measure of the performance of the vat with respect to release-capability. This has been tested at increasing manufacturing rates. The new self-peeling vat outperformed industrial state-of-the-art vats by 814% percent....

On possibility of high energy electron irradiation usage for material alloying

International Nuclear Information System (INIS)

Vladimirskij, R.A.; Livshits, V.B.; Payuk, V.A.; Plotnikov, S.V.; Kuz'minykh, V.A.

1988-01-01

Review of papers concerning over 2.5 MeV fast electron beam (FEB) irradiation of metals and semiconductors is made. It makes possible to transform physical and mechanical properties ofsurface layers due to their alloyage with different elements or due to redistribution of alloy impurities at the essential depth. It is shown, that electron beam irradiation of materials results in the formation of essential temperature gradient in the sample near the surface and defect nonequilibrium concentration. Along with the increase of diffusion effective ratio the heterogeneous distribution of temperature and defects results in the formation of atom nucompensated fluxes within the sample, which result in element redistribution. Drift of one element through the layer of the second one occurs as a result. Gradient of temperature and defects, amfient temperature and correlation of migration activation energies of element atoms are considered as determining factors at anomalous mass transfer

EIA new releases

International Nuclear Information System (INIS)

1994-12-01

This report was prepared by the Energy Information Administration. It contains news releases on items of interest to the petroleum, coal, nuclear, electric and alternate fuels industries ranging from economic outlooks to environmental concerns. There is also a listing of reports by industry and an energy education resource listing containing sources for free or low-cost energy-related educational materials for educators and primary and secondary students

Development of a novel resin-based dental material with dual biocidal modes and sustained release of Ag+ ions based on photocurable core-shell AgBr/cationic polymer nanocomposites.

Science.gov (United States)

Cao, Weiwei; Zhang, Yu; Wang, Xi; Chen, Yinyan; Li, Qiang; Xing, Xiaodong; Xiao, Yuhong; Peng, Xuefeng; Ye, Zhiwen

2017-07-01

Research on the incorporation of cutting-edge nano-antibacterial agent for designing dental materials with potent and long-lasting antibacterial property is demanding and provoking work. In this study, a novel resin-based dental material containing photocurable core-shell AgBr/cationic polymer nanocomposite (AgBr/BHPVP) was designed and developed. The shell of polymerizable cationic polymer not only provided non-releasing antibacterial capability for dental resins, but also had the potential to polymerize with other methacrylate monomers and prevented nanoparticles from aggregating in the resin matrix. As a result, incorporation of AgBr/BHPVP nanocomposites did not adversely affect the flexural strength and modulus but greatly increased the Vicker's hardness of resin disks. By continuing to release Ag + ions without the impact of anaerobic environment, resins containing AgBr/BHPVP nanoparticles are particularly suitable to combat anaerobic cariogenic bacteria. By reason of the combined bactericidal effect of the contact-killing cationic polymers and the releasing-killing Ag + ions, AgBr/BHPVP-containing resin disks had potent bactericidal activity against S. mutans. The long-lasting antibacterial activity was also achieved through the sustained release of Ag + ions due to the core-shell structure of the nanocomposites. The results of macrophage cytotoxicity showed that the cell viability of dental resins loading less than 1.0 wt% AgBr/BHPVP was close to that of neat resins. The AgBr/BHPVP-containing dental resin with dual bactericidal capability and long term antimicrobial effect is a promising material aimed at preventing second caries and prolonging the longevity of resin composite restorations.

EURDYN: computer programs for the nonlinear transient analysis of structures submitted to dynamic loading. EURDYN (Release 3): users' manual

International Nuclear Information System (INIS)

Halleux, J.P.

1983-01-01

The EURDYN computer codes are mainly designed for the simulation of nonlinear dynamic response of fast-reactor compoments submitted to impulse loading due to abnormal working conditions. Two releases of the structural computer codes EURDYN 01 (2-D beams and triangles and axisymmetric conical shells and triangular tores), 02 (axisymmetric and 2-D quadratic isoparametric elements) and 03 (triangular plate elements) have already been produced. They include material (elasto-plasticity using the classical flow theory approach) and geometrical (large displacements and rotations treated by a corotational technique) nonlinearities. The new features of Release 3 roughly consist in: full large strain capability for 9-node isoparametric elements, generalized array dimensions, introduction of the radial return algorithm for elasto-plastic material modelling, extension of the energy check facility to the case of prescribed displacements, and, possible interface to a post-processing package including time plot facilities

Influence of additives and impurities in sweep gas and solid tritium release behaviour from lithium ceramics (review)

International Nuclear Information System (INIS)

Tanaka, Satoru

1991-01-01

Tritium release from solid breeding material is affected by small amounts of additives or impurities in the sweep gas or solid itself. Addition of hydrogen or water vapor to the sweep gas is reported to enhance the surface reaction of tritium release. Doping to solid breeder with elements of different valence from lithium has a possibility to improve tritium diffusion in the solid. Surface reaction and migration behavior in bulk are believed to be also affected by impurities in the sweep gas and in the solid. In order to model tritium release behavior in the blanket of fusion reactor, the mechanism of interaction with these additives or impurities must be quantitatively formulated. However, the mechanism of these remains to be elucidated. In this paper effects of these additives and impurities on tritium migration are reviewed. The mechanism of surface reaction for He+H 2 sweep gas is also discussed. (orig.)

Modeling the release, spreading, and burning of LNG, LPG, and gasoline on water

International Nuclear Information System (INIS)

Johnson, David W.; Cornwell, John B.

2007-01-01

Current interest in the shipment of liquefied natural gas (LNG) has renewed the debate about the safety of shipping large volumes of flammable fuels. The size of a spreading pool following a release of LNG from an LNG tank ship has been the subject of numerous papers and studies dating back to the mid-1970s. Several papers have presented idealized views of how the LNG would be released and spread across a quiescent water surface. There is a considerable amount of publicly available material describing these idealized releases, but little discussion of how other flammable fuels would behave if released from similar sized ships. The purpose of this paper is to determine whether the models currently available from the United States Federal Energy Regulatory Commission (FERC) can be used to simulate the release, spreading, vaporization, and pool fire impacts for materials other than LNG, and if so, identify which material-specific parameters are required. The review of the basic equations and principles in FERC's LNG release, spreading, and burning models did not reveal a critical fault that would prevent their use in evaluating the consequences of other flammable fluid releases. With the correct physical data, the models can be used with the same level of confidence for materials such as LPG and gasoline as they are for LNG

A guide to the use of TIRION. A computer programme for the calculation of the consequences of releasing radioactive material to the atmosphere

International Nuclear Information System (INIS)

Kaiser, G.D.

1976-11-01

A brief description is given of the contents of TIRION, which is a computer program that has been written for use in calculations of the consequences of releasing radioactive material to the atmosphere. This is followed by a section devoted to an account of the control and data cards that make up the input to TIRION. (author)

The Atmospheric Release Advisory Capability Site Workstation System

International Nuclear Information System (INIS)

Foster, K.T.; Sumikawa, D.A.; Foster, C.S.; Baskett, R.L.

1993-01-01

The Atmospheric Release Advisory Capability (ARAC) is a centralized emergency response service that assesses the consequences that may result from an atmospheric release of toxic material. ARAC was developed by the Lawrence Livermore National Laboratory (LLNL) for the Departments of Energy (DOE) and Defense (DOD) and responds principally to radiological accidents. ARAC provides radiological health and safety guidance to decision makers in the form of computer-generated estimates of the effects of an actual, or potential release of radioactive material into the atmosphere. Upon receipt of the release scenario, the ARAC assessment staff extracts meteorological, topographic, and geographic data from resident world-wide databases for use in complex, three-dimensional transport and diffusion models. These dispersion models generate air concentration (or dose) and ground deposition contour plots showing estimates of the contamination patterns produced as the toxic material is carried by the prevailing winds. To facilitate the ARAC response to a release from specific DOE and DOD sites and to provide these sites with a local emergency response tool, a remote Site Workstation System (SWS) is being placed at various ARAC-supported facilities across the country.. This SWS replaces the existing antiquated ARAC Site System now installed at many of these sites. The new system gives users access to complex atmospheric dispersion models that may be run either by the ARAC staff at LLNL, or (in a later phase of the system) by site personnel using the computational resources of the SWS. Supporting this primary function are a variety of SWS-resident supplemental capabilities that include meteorological data acquisition, manipulation of release-specific databases, computer-based communications, and the use of a simpler Gaussian trajectory puff model that is based on Environmental Protection Agency's INPUFF code

[Research on controlling iron release of desalted water transmitted in existing water distribution system].

Science.gov (United States)

Tian, Yi-Mei; Liu, Yang; Zhao, Peng; Shan, Jin-Lin; Yang, Suo-Yin; Liu, Wei

2012-04-01

Desalted water, with strong corrosion characteristics, would possibly lead to serious "red water" when transmitted and distributed in existing municipal water distribution network. The main reason for red water phenomenon is iron release in water pipes. In order to study the methods of controlling iron release in existing drinking water distribution pipe, tubercle analysis of steel pipe and cast iron pipe, which have served the distribution system for 30-40 years, was carried out, the main construction materials were Fe3O4 and FeOOH; and immersion experiments were carried in more corrosive pipes. Through changing mixing volume of tap water and desalted water, pH, alkalinity, chloride and sulfate, the influence of different water quality indexes on iron release were mainly analyzed. Meanwhile, based on controlling iron content, water quality conditions were established to meet with the safety distribution of desalted water: volume ratio of potable water and desalted water should be higher than or equal to 2, pH was higher than 7.6, alkalinity was higher than 200 mg x L(-1).

Releases of radioactivity at the Savannah River Plant, 1954--1985

International Nuclear Information System (INIS)

Zeigler, C.C.; Lawrimore, I.B.

1988-07-01

Radioactive releases from Savannah River Plant (SRP) facilities to air, water and earthen seepage basins have been monitored and tabulated throughout the history of the site. The purpose of this report is to provide a source of data on routine releases of radioactivity to air, water and seepage basins that can be used for analyses of trends, environmental impact, etc. As used in this report, routine radioactive releases means radioactive materials that are released through established effluents from process facilities. This report provides a summary of radioactive releases that inflects the release values contained m records and documents from startup through 1985

Initial integration of accident safety, waste management, recycling, effluent, and maintenance considerations for low-activation materials

International Nuclear Information System (INIS)

Piet, S.J.; Herring, J.S.; Cheng, E.T.; Fetter, S.

1991-01-01

A true low-activation material should ideally achieve all of the following objectives: 1. The possible prompt dose at the site boundary from 100% release of the inventory should be <2 Sv (200 rem); hence, the design would be inherently safe in that no possible accident could result in prompt radiation fatalities. 2. The possible cancers from realistic releases should be limited such that the accident risk is <0.1%/yr of the existing background cancer risk to local residents. This includes consideration of elemental volatility. 3. The decay heat should be limited so that active mitigative measures are not needed to protect the investment from cooling transients; hence, the design would be passively safe with respect to decay heat. 4. Used materials could be either recycled or disposed of as near- surface waste. 5. Hands-on maintenance should be possible around coolant system piping and components such as the heat exchanger. 6. Effluent of activation products should be minor compared to the major challenge of limiting tritium effluents. The most recent studies in these areas are used to determine which individual elements and engineering materials are low activation. Grades from A (best) to G (worst) are given to each element in the areas of accident safety, recycling, and waste management. Structure/fluid combinations are examined for low-activation effluents and out-of-blanket maintenance. The lowest activation structural materials are silicon carbide, vanadium alloys, and ferritic steels. Impurities and minor alloying constituents must be carefully considered. The lowest activation coolants are helium, water, FLiBe, and lithium. The lowest activation breeders are lithium, lithium oxide, lithium silicate, and FLiBe. Designs focusing on these truly low-activation materials will help achieve the excellent safety and environmental potential of fusion energy

In vitro studies of copper release from powder particles in synthetic biological media

International Nuclear Information System (INIS)

Midander, Klara; Wallinder, Inger Odnevall; Leygraf, Christofer

2007-01-01

The aim of this paper is to provide quantitative data on copper release from powder particles of different copper materials, including artificial copper patina, Cu 2 O and metallic Cu, when exposed to different synthetic biological media to simulate an inhalation scenario and/or skin contact. Generated data may contribute in risk assessment of potential health effects following exposure to and handling of various copper materials. All tests were performed in vitro to determine total copper concentrations, release rates of total copper, and to elucidate its time-dependence. The copper release process was interpreted in terms of specific surface area, surface morphology-, and composition. All powder materials show a time-dependent release process with total copper release rates less than 3 μg/cm 2 per hour at steady state conditions, for all media investigated. The importance of using relevant test media when simulating different interstitial lung conditions and difficulties encountered when comparing powder particles of essentially different properties are thoroughly discussed. - Copper release rates from particles are essential to assess potential health aspects

Review on phase change materials for building applications

Directory of Open Access Journals (Sweden)

Lavinia SOCACIU

2014-11-01

Full Text Available In nowadays, the Phase Change Material (PCM is a viable alternative for reducing the energy consumption and for increase the thermal comfort in buildings. The use of PCM in building applications provides the potential to increase the indoor thermal comfort for occupants due to the reduced indoor temperature fluctuations and lower global energy consumption. The possibility to incorporate the PCM into the material of construction for cooling and heating the buildings gained the interest of researchers from all the world because the PCM have a high heat of fusion, meaning it is capable to storing and release large amounts of energy in the form of heat during its melting and solidifying process at a specific temperature.

Guidelines for calculating radiation doses to the public from a release of airborne radioactive material under hypothetical accident conditions in nuclear reactors

International Nuclear Information System (INIS)

1991-04-01

This standard provides guidelines and a methodology for calculating effective doses and thyroid doses to people (either individually or collectively) in the path of airborne radioactive material released from a nuclear facility following a hypothetical accident. The radionuclides considered are those associated with substances having the greatest potential for becoming airborne in reactor accidents: tritium (HTO), noble gases and their daughters, radioiodines, and certain radioactive particulates (Cs, Ru, Sr, Te). The standard focuses on the calculation of radiation doses for external exposures from radioactive material in the cloud; internal exposures for inhalation of radioactive material in the cloud and skin penetration of tritium; and external exposures from radionuclides deposited on the ground. It uses as modified Gaussian plume model to evaluate the time-integrated concentration downwind. (52 refs., 12 tabs., 21 figs.)

Development of a mobile dose prediction system based on artificial neural networks for NPP emergencies with radioactive material releases

International Nuclear Information System (INIS)

Pereira, Claudio M.N.A.; Schirru, Roberto; Gomes, Kelcio J.; Cunha, José L.

2017-01-01

This work presents the approach of a mobile dose prediction system for NPP emergencies with nuclear material release. The objective is to provide extra support to field teams decisions when plant information systems are not available. However, predicting doses due to atmospheric dispersion of radionuclide generally requires execution of complex and computationally intensive physical models. In order to allow such predictions to be made by using limited computational resources such as mobile phones, it is proposed the use of artificial neural networks (ANN) previously trained (offline) with data generated by precise simulations using the NPP atmospheric dispersion system. Typical situations for each postulated accident and respective source terms, as well as a wide range of meteorological conditions have been considered. As a first step, several ANN architectures have been investigated in order to evaluate their ability for dose prediction in hypothetical scenarios in the vicinity of CNAAA Brazilian NPP, in Angra dos Reis, Brazil. As a result, good generalization and a correlation coefficient of 0.99 was achieved for a validation data set (untrained patterns). Then, selected ANNs have been coded in Java programming language to run as an Android application aimed to plot the spatial dose distribution into a map. In this paper, the general architecture of the proposed system is described; numerical results and comparisons between investigated ANN architectures are discussed; performance and limitations of running the Application into a commercial mobile phone are evaluated and possible improvements and future works are pointed.

SIMULATION OF VINPOCETINE RELEASE PROCESS FROM MICROCAPSULES WITH HYDROPHOBIC SHELL

Directory of Open Access Journals (Sweden)

Yu. A. Polkovnikova

2017-01-01

Full Text Available Nowadays microcapsules are widely spread in different industries. Microcapsules with vitamins, etheric and fatty oils are included into different cosmetics (creams, gels, serums. Microencapsulated probiotics are used in foods and fodder additives in veterinary. An important field of application of microencapsulation in pharmacy is the combination in the total dosage of drugs that are incompatible when mixed in free form.The aim of work is a comparative analysis of thermodynamic characteristics of vinpocetine release from the melt of beeswax and cacao butter 3:2 into water, solution of hydrochloric acid 0.01 M and ethanol.Materials and methods. For simulation of the process of vinpocetine release from the melt into different environments models component models of the studied systems were built and their atom charges were calculated by quantum-chemical method. Spatial models of the components were built in Hyper Chem 8.01. As an initial state for the thermodynamic characteristics of the calculation of vinpocetine release from the melt, a conformation of «melt-vinpocetine» system was used after thermodynamic equilibration by molecular dynamics simulation in Bioeurica program for 5 ns. For isolated systems a vibrational analysis was performed with the use of unrestricted Hartree-Fock method in STO-3G basis set in Orca 4.0 program.Results and discussion. Vinpocetine release from the melt of beeswax and cacao butter 3:2 into water with different pH values and to ethanol depends on its solubility in these environments, and also on solubility of the melt.Conclusion. The performed study of vinpocetine release from the melt of beeswax and cacao butter 3:2 by molecular dynamics simulation demonstrates the opportunity of vinpocetine release into water with pH=2 and into ethanol. The obtained results make it possible to assume a lower degree of vinpocetine release from the melt into ethanol compared with the solution of hydrochloric acid 0,01 M.

GPU-based parallel computing in real-time modeling of atmospheric transport and diffusion of radioactive material

Energy Technology Data Exchange (ETDEWEB)

Santos, Marcelo C. dos; Pereira, Claudio M.N.A.; Schirru, Roberto; Pinheiro, André, E-mail: jovitamarcelo@gmail.com, E-mail: cmnap@ien.gov.br, E-mail: schirru@lmp.ufrj.br, E-mail: apinheiro99@gmail.com [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Coordenacao de Pos-Graduacao e Pesquisa de Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear

2017-07-01

Atmospheric radionuclide dispersion systems (ARDS) are essential mechanisms to predict the consequences of unexpected radioactive releases from nuclear power plants. Considering, that during an eventuality of an accident with a radioactive material release, an accurate forecast is vital to guide the evacuation plan of the possible affected areas. However, in order to predict the dispersion of the radioactive material and its impact on the environment, the model must process information about source term (radioactive materials released, activities and location), weather condition (wind, humidity and precipitation) and geographical characteristics (topography). Furthermore, ARDS is basically composed of 4 main modules: Source Term, Wind Field, Plume Dispersion and Doses Calculations. The Wind Field and Plume Dispersion modules are the ones that require a high computational performance to achieve accurate results within an acceptable time. Taking this into account, this work focuses on the development of a GPU-based parallel Plume Dispersion module, focusing on the radionuclide transport and diffusion calculations, which use a given wind field and a released source term as parameters. The program is being developed using the C ++ programming language, allied with CUDA libraries. In comparative case study between a parallel and sequential version of the slower function of the Plume Dispersion module, a speedup of 11.63 times could be observed. (author)

GPU-based parallel computing in real-time modeling of atmospheric transport and diffusion of radioactive material

International Nuclear Information System (INIS)

Santos, Marcelo C. dos; Pereira, Claudio M.N.A.; Schirru, Roberto; Pinheiro, André; Coordenacao de Pos-Graduacao e Pesquisa de Engenharia

2017-01-01

Atmospheric radionuclide dispersion systems (ARDS) are essential mechanisms to predict the consequences of unexpected radioactive releases from nuclear power plants. Considering, that during an eventuality of an accident with a radioactive material release, an accurate forecast is vital to guide the evacuation plan of the possible affected areas. However, in order to predict the dispersion of the radioactive material and its impact on the environment, the model must process information about source term (radioactive materials released, activities and location), weather condition (wind, humidity and precipitation) and geographical characteristics (topography). Furthermore, ARDS is basically composed of 4 main modules: Source Term, Wind Field, Plume Dispersion and Doses Calculations. The Wind Field and Plume Dispersion modules are the ones that require a high computational performance to achieve accurate results within an acceptable time. Taking this into account, this work focuses on the development of a GPU-based parallel Plume Dispersion module, focusing on the radionuclide transport and diffusion calculations, which use a given wind field and a released source term as parameters. The program is being developed using the C ++ programming language, allied with CUDA libraries. In comparative case study between a parallel and sequential version of the slower function of the Plume Dispersion module, a speedup of 11.63 times could be observed. (author)

Determination of phthalates released from paper packaging materials by solid-phase extraction-high-performance liquid chromatography.

Science.gov (United States)

Gao, Xin; Yang, Bofeng; Tang, Zhixu; Luo, Xin; Wang, Fengmei; Xu, Hui; Cai, Xue

2014-01-01

A solid phase extraction (SPE) high-performance liquid chromatography (HPLC) method was developed for the simultaneous determination of 10 phthalic acid esters (dimethyl phthalate, diethyl phthalate, dipropyl phthalate, benzylbutyl phthalate, diisobutyl phthalate, dicyclohexyl phthalate, diamyl phthalate, di-n-hexyl phthalate, di-n-octyl phthalate and di-2-ethylhexyl phthalate) released from food paper packaging materials. The use of distilled water, 3% acetic acid (w/v), 10% ethanol (v/v) and 95% ethanol (v/v) instead of the different types of food simulated the migration of 10 phthalic acid esters from food paper packaging materials; the phthalic acid esters in four food simulants were enriched and purified by a C18 SPE column and nitrogen blowing, and quantified by HPLC with a diode array detector. The chromatographic conditions and extraction conditions were optimized and all 10 of the phthalate acid esters had a maximum absorbance at 224 nm. The method showed limitations of detection in the range of 6.0-23.8 ng/mL the correlation coefficients were greater than 0.9999 in all cases, recovery values ranged between 71.27 and 106.97% at spiking levels of 30, 60 and 90 ng/mL and relative standard deviation values ranged from 0.86 to 8.00%. The method was considered to be simple, fast and reliable for a study on the migration of these 10 phthalic acid esters from food paper packaging materials into food.

Elution of Monomers from Provisional Composite Materials

Directory of Open Access Journals (Sweden)

Simon Daniel Schulz

2015-01-01

Full Text Available The aim of this study was to evaluate the elution of substances from different materials used for the manufacturing of temporary indirect restorations, after storage in saliva and ethanol 75%. 10 samples of three chemically cured materials (Protemp 3 Garant, Systemp.c&b, and Trim and one light-cured material (Clip F were stored in saliva and ethanol 75% for 24 h, 7, and days 28 days. From the storage media at each time period, samples were prepared and analysed by LC-MS/MS, in order to access the elution of monomers. The results differed among the materials (P ≤ 0.05. No monomers were detected in the samples of Protemp 3 Garant and Clip F. Substances were detected only in ethanol samples of Systemp.c&b and Trim. The amount of BisGMA, TEGDMA, and UDMA 2 released from Systemp.c&b was higher compared to Trim. Storage time affected the release of substances (P ≤ 0.05. The highest release was observed within the first 24 h. It can be concluded that provisional resin composite materials do not show high release of monomers and this release is material dependent. However, the detection of additional peaks during the analysis, suggesting the formation of by-products of the eluted substances, may not be in favour of these materials with respect to their toxicity.

Surface radiological free release program for the Battelle Columbus Laboratory Decommissioning Project

International Nuclear Information System (INIS)

Horton, C.N.

1995-01-01

This paper was prepared for the Second Residual Radioactivity and Recycling Criteria Workshop and discusses decommissioning and decontamination activities at the Battelle Columbus Laboratories Decommissioning Project (BCLDP). The BCLDP is a joint effort between the Department of Energy (DOE) and Battelle Columbus Operations to decontaminate fifteen Battelle-owned buildings contaminated with DOE radioactive materials. The privately owned buildings located across the street from The Ohio State University campus became contaminated with natural uranium and thorium during nuclear research activities. BCLDP waste management is supported by an extensive radiological free-release program. Miscellaneous materials and building surfaces have been free-released from the BCLDP. The free-release program has substantially reduced radioactive waste volumes and supported waste minimization. Free release for unrestricted use has challenged regulators and NRC licensees since the development of early surface-release criteria. This paper discusses the surface radiological free-release program incorporated by the BCLDP and the historical development of the surface radiological free-release criteria. Concerns regarding radiological free-release criteria are also presented. (author)

Molding method of buffer material for underground disposal of radiation-contaminated material, and molded buffer material

International Nuclear Information System (INIS)

Akasaka, Hidenari; Shimura, Satoshi; Kawakami, Susumu; Ninomiya, Nobuo; Yamagata, Junji; Asano, Eiichi

1995-01-01

Upon molding of a buffer material to be used upon burying a vessel containing radiation-contaminated materials in a sealed state, a powdery buffer material to be molded such as bentonite is disposed at the periphery of a mandrel having a cylindrical portion somewhat larger than contaminate container to be subjected to underground disposal. In addition, it is subjected to integration-molding such as cold isotropic press with a plastic film being disposed therearound, to form a molding product at high density. The molding product is released and taken out with the plastic film being disposed thereon. Releasability from an elastic mold is improved by the presence of the plastic film. In addition, if it is stored or transported while having the plastic film being disposed thereon, swelling of the buffer material due to water absorption or moisture absorption can be suppressed. (T.M.)

Release strategies for rehabilitated sea otters

Science.gov (United States)

DeGange, Anthony R.; Ballachey, Brenda E.; Bayha, Keith; Williams, Terrie M.; Davis, Randall W.

1995-01-01

According to the U.S. Fish and Wildlife Services’ (USFWS) Response Plan for sea otters (USFWS, in preparation), in the event of an oil spill, the decision to release sea otters from rehabilitation centers following treatment will be linked to the decision on whether to capture sea otters for treatment. Assuming a scenario similar to the Exxon Valdez oil spill (EVOS), once the decision to capture sea otters is made, the ultimate goal is to return as many sea otters to the wild as possible, even though the rescue may not be expected to produce results significant at the population level. The decision by the USFWS to proceed with capture, rehabilitation, and release will be made on a case-by-case basis (USFWS, in preparation). Many factors will influence the decision. Perhaps the most important factors in deciding when and where to release sea otters are the location and availability of suitable release sites and verification that the otters are free of diseases that might be transmitted to the wild population.Alternative release strategies for sea otters will be contained in the sea otter response portion of the USFWS’s oil spill contingency plans for Alaska and California that are being developed as required by the Oil Pollution Act of 1990. Public review of these plans before they are implemented will help to reduce public concern about the survival of rehabilitated otters, their biological effect on the release area, and the potential introduction or spread of disease into the wild sea otter population.The objective of this chapter is to review alternative strategies for the disposition of rehabilitated sea otters. Our assumption is that returning as many animals to the wild as possible, whether it be for humanitarian or biological reasons, is the ultimate goal of this effort (Figure 10.1).

WATER HYACINTH: A POSSIBLE ALTERNATIVE RATE RETARDING NATURAL POLYMER USED IN SUSTAINED RELEASE TABLET DESIGN

Directory of Open Access Journals (Sweden)

Sabera eKhatun

2014-06-01

Full Text Available In recent years natural polymers have been widely used, because of their effectiveness and availability over synthetic polymers. In this present investigation matrix tablets of Metformin hydrochloride were formulated using Water hyacinth powder and its rate retardant activity was studied. Tablets were prepared using wet granulation method with 8% starch as granulating agent and 5%, 10%, 15%, 20%, 25% and 30% of Water hyacinth powder to the drug. In preformulation study, angle of repose, Carr’s Index and Hausner ratio were calculated. Fourier Transform Infrared Spectroscopy (FTIR, Differential Scanning Calorimetry (DSC and Scanning Electron Microscopy (SEM studies were performed and no interactions were found between drug and excipients. Weight variation, friability, hardness, thickness, diameter, and in vitro release study were performed with the prepared matrix tablets. Dissolution studies were conducted using USP type II apparatus at a speed of 100 rpm at 37oC ± 0.5 temperature, for 8 hours. All the formulations comply with both BP and USP requirements, but among all the formulations F-1 (5% of Water hyacinth was the best fitted formula. The drug release patterns were explained in different kinetic models such as Zero order, First order, Higuchi, Hixson Crowell and Korsmeyer-Peppas equations. The current investigation implies that Water hyacinth has the potential to be used as a rate-retarding agent in sustained release drug formulations.

Water hyacinth: a possible alternative rate retarding natural polymer used in sustained release tablet design.

Science.gov (United States)

Khatun, Sabera; Sutradhar, Kumar B

2014-01-01

In recent years natural polymers have been widely used because of their effectiveness and availability over synthetic polymers. In this present investigation matrix tablets of Metformin hydrochloride were formulated using Water hyacinth powder and its rate retardant activity was studied. Tablets were prepared using wet granulation method with 8% starch as granulating agent and 5, 10, 15, 20, 25 and 30% of Water hyacinth powder to the drug. In preformulation study, angle of repose, Carr's Index and Hausner ratio were calculated. Fourier Transform Infrared Spectroscopy (FTIR), Differential Scanning Calorimetry (DSC), and Scanning Electron Microscopy (SEM) studies were performed and no interactions were found between drug and excipients. Weight variation, friability, hardness, thickness, diameter, and in vitro release study were performed with the prepared matrix tablets. Dissolution studies were conducted using USP type II apparatus at a speed of 100 rpm at 37°C ± 0.5 temperature for 8 h. Though all the formulations comply with both BP and USP requirements, formulation F-1 (5% of Water hyacinth) was the best fitted formula. The drug release patterns were explained in different kinetic models such as Zero order, First order, Higuchi, Hixson Crowell, and Korsmeyer-Peppas equations. The current investigation implies that Water hyacinth has the potential to be used as a rate-retarding agent in sustained release drug formulations.

Potential release scenarios for carbon nanotubes used in composites

Science.gov (United States)

The expected widespread use of carbon nanotube (CNT)-composites in consumer products calls for an assessment of the possible release and exposure to workers, consumers and the environment. Release of CNTs may occur at all steps in the life cycle of products, but to date only limi...

Possibilities and Challenges of Scanning Hard X-ray Spectro-microscopy Techniques in Material Sciences

Directory of Open Access Journals (Sweden)

Andrea Somogyi

2015-06-01

Full Text Available Scanning hard X-ray spectro-microscopic imaging opens unprecedented possibilities in the study of inhomogeneous samples at different length-scales. It gives insight into the spatial variation of the major and minor components, impurities and dopants of the sample, and their chemical and electronic states at micro- and nano-meter scales. Measuring, modelling and understanding novel properties of laterally confined structures are now attainable. The large penetration depth of hard X-rays (several keV to several 10 keV beam energy makes the study of layered and buried structures possible also in in situ and in operando conditions. The combination of different X-ray analytical techniques complementary to scanning spectro-microscopy, such as X-ray diffraction, X-ray excited optical luminescence, secondary ion mass spectrometry (SIMS and nano-SIMS, provides access to optical characteristics and strain and stress distributions. Complex sample environments (temperature, pressure, controlled atmosphere/vacuum, chemical environment are also possible and were demonstrated, and allow as well the combination with other analysis techniques (Raman spectroscopy, infrared imaging, mechanical tensile devices, etc. on precisely the very same area of the sample. The use of the coherence properties of X-rays from synchrotron sources is triggering emerging experimental imaging approaches with nanometer lateral resolution. New fast analytical possibilities pave the way towards statistically significant studies at multi- length-scales and three dimensional tomographic investigations. This paper gives an overview of these techniques and their recent achievements in the field of material sciences.

7 CFR 2902.36 - Concrete and asphalt release fluids.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Concrete and asphalt release fluids. 2902.36 Section... PROCUREMENT Designated Items § 2902.36 Concrete and asphalt release fluids. (a) Definition. Products that are designed to provide a lubricating barrier between the composite surface materials (e.g., concrete or...

Extended latanoprost release from commercial contact lenses: in vitro studies using corneal models.

Directory of Open Access Journals (Sweden)

Saman Mohammadi

Full Text Available In this study, we compared, for the first time, the release of a 432 kDa prostaglandin F2a analogue drug, Latanoprost, from commercially available contact lenses using in vitro models with corneal epithelial cells. Conventional polyHEMA-based and silicone hydrogel soft contact lenses were soaked in drug solution (131 μg = ml solution in phosphate buffered saline. The drug release from the contact lens material and its diffusion through three in vitro models was studied. The three in vitro models consisted of a polyethylene terephthalate (PET membrane without corneal epithelial cells, a PET membrane with a monolayer of human corneal epithelial cells (HCEC, and a PET membrane with stratified HCEC. In the cell-based in vitro corneal epithelium models, a zero order release was obtained with the silicone hydrogel materials (linear for the duration of the experiment whereby, after 48 hours, between 4 to 6 μg of latanoprost (an amount well within the range of the prescribed daily dose for glaucoma patients was released. In the absence of cells, a significantly lower amount of drug, between 0.3 to 0.5 μg, was released, (p <0:001. The difference observed in release from the hydrogel lens materials in the presence and absence of cells emphasizes the importance of using an in vitro corneal model that is more representative of the physiological conditions in the eye to more adequately characterize ophthalmic drug delivery materials. Our results demonstrate how in vitro models with corneal epithelial cells may allow better prediction of in vivo release. It also highlights the potential of drug-soaked silicone hydrogel contact lens materials for drug delivery purposes.

Estimated airborne release of plutonium from Atomics International's Nuclear Materials Development Facility in the Santa Susana site, California, as a result of postulated damage from severe wind and earthquake hazard

International Nuclear Information System (INIS)

Mishima, J.; Ayer, J.E.

1981-09-01

The potential mass of airborne releases of plutonium (source term) that could result from wind and seismic damage is estimated for the Atomics International Company's Nuclear Materials Development Facility (NMDF) at the Santa Susana site in California. The postulated source terms will be useful as the basis for estimating the potential dose to the maximum exposed individual by inhalation and to the total population living within a prescribed radius of the site. The respirable fraction of airborne particles is thus the principal concern. The estimated source terms are based on the damage ratio, and the potential airborne releases if all enclosures suffer particular levels of damage. In an attempt to provide a realistic range of potential source terms that include most of the normal processing conditions, a best estimate bounded by upper and lower limits is provided. The range of source terms is calculated by combining a high best estimate and a low damage ratio, based on a fraction of enclosures suffering crush or perforation, with the airborne release from enclosures based upon an upper limit, average, and lower limit inventory of dispersible materials at risk. Two throughput levels are considered. The factors used to evaluate the fractional airborne release of materials and the exchange rates between enclosed and exterior atmospheres are discussed. The postulated damage and source terms are discussed for wind and earthquake hazard scenarios in order of their increasing severity

Site release in the decommissioning of nuclear installations

International Nuclear Information System (INIS)

Revilla, Jose Luis; Sanz, Maria Teresa; Marugan, Inmaculada; Simon, Inmaculada; Martin, Manuel; Solis, Susana; Sterling, Agustina

2008-01-01

Spanish regulatory framework for the decommissioning process of a nuclear facility ends up with a decommission statement, which releases the licence-holder of the facility from its responsibilities as an operator. It also establishes -where a restricted site release applies- the appropriate future use restrictions, and the responsible of both maintaining such restrictions and ensuring their compliance. Releasing a site implies eliminating all radiological monitoring. The Regulations, however, did not specify either the radiological conditions to be met for the site to be released, or the possibility of a partial release -with or without restrictions-. In case of restricted site release, the Regulations did not specify either the required criteria for such a release. This paper presents the main features of the Safety Instruction IS-13 'Radiological criteria for the release of nuclear facilities sites' issued recently by the Spanish Nuclear Safety Council as a new specific regulation. This Safety Instruction establishes the requirements and conditions for the release of nuclear facility sites, that is, radiological criteria on the effective dose to the public, partial release of nuclear facility sites and restricted release of nuclear facility sites. (author).

PAVAN, Atmospheric Dispersion of Radioactive Releases from Nuclear Power Plants

International Nuclear Information System (INIS)

2001-01-01

1 - Description of program or function: PAVAN estimates down-wind ground-level air concentrations for potential accidental releases of radioactive material from nuclear facilities. Options can account for variation in the location of release points, additional plume dispersion due to building wakes, plume meander under low wind speed conditions, and adjustments to consider non-straight trajectories. It computes an effective plume height using the physical release height which can be reduced by inputted terrain features. 2 - Method of solution: Using joint frequency distributions of wind direction and wind speed by atmospheric stability, the program provides relative air concentration (X/Q) values as functions of direction for various time periods at the exclusion area boundary (EAB) and the outer boundary of the low population zone (LPZ). Calculations of X/Q values can be made for assumed ground-level releases or evaluated releases from free-standing stacks. The X/Q calculations are based on the theory that material released to the atmosphere will be normally distributed (Gaussian) about the plume centerline. A straight-line trajectory is assumed between the point of release and all distances for which X/Q values are calculated. 3 - Restrictions on the complexity of the problem: - The code cannot handle multiple emission sources

Effects of membrane composition on release of model hydrophilic compound from osmotic delivery systems.

Science.gov (United States)

Ozdemir, N; Ozalp, Y; Ozkan, Y

2000-01-01

In this study, the effects of surface-active agents in different types and concentrations, added into the coating solution, on release of model hydrophilic compound have been examined. For this purpose, the tablets, prepared with the use of methylene blue as a model substance, were coated by spray coating technique with cellulose acetate solution containing polyethylene glycol 400 as a plasticizer. In addition, cetylpyridinium chloride as cationic surface-active agent and sodium lauryl sulphate as anionic surface-active agent were added into coating solution in different concentrations. After creating a delivery orifice by a microdrill on the tablets, release of model hydrophilic compound was tested by the USP paddle method. The data obtained were evaluated according to the different kinetics and the mechanism of release from the preparations was examined. The surface properties of the coating material were investigated by scanning electron microscope taken before and after the contact with medium fluid, as well as the mechanical properties by tensile tests. In conclusion, it has been found that the cationic surface active agent, cetylpyridinium chloride reduced the lag time, observed during the release of model hydrophilic compound, as a result of its enhancing effect on wettability of tablets by reducing the contact angle between the medium fluid and the coating material. On the other hand, the anionic surface active agent, sodium lauryl sulphate has been inactivated possibly due to the interaction with model hydrophilic compound that has cationic properties and/or substances contained in membrane composition; thus, the lag time has not decreased and furthermore, a significant decrease in the delivery rate of model hydrophilic compound has been observed.

Modelling for radiological and radioecological consequences of an accidental radionuclide release at Sea

International Nuclear Information System (INIS)

Paschoa, A.S.

1997-01-01

Full text: Scenarios concerning accidental releases of radionuclides into water bodies can be found in the open literature, mostly in connection with nuclear power plants located either onshore or inland. However, meager attention has been given to nuclear reactors used as energy sources for propulsion at sea, which are also subject to accidents. Such potential accidents may involve the loss of part of the reactor core to the surrounding water body. In addition of the initial instantaneous releases, one can estimate delayed source terms based on the rate at which radionuclides are dissolved or leached from the solidified material, like part of the core or structural materials in contact with water. Most of such solidified material might be a mixture of uranium, zirconium, iron, calcium, silica, fission and activation products, and transuranium elements as oxides, forming a glassy type solid. Transport models were used to calculate radionuclide concentrations in water resulting from short and delayed source terms. Oceanographic data used in the calculations were taken either from the open literature or from unclassified reports of the Brazilian Navy, being, however, as generic as possible. Time-dependent concentration functions for radionuclides in aquatic food following an accidental release reflect the net result of intake and elimination processes. However, to avoid the complexities of multiple parameters involved in such processes, the model accounts only for trophic transfer of radionuclides, and yet avoids the necessity of analyzing the details of each transfer step used to determine fish, crustacea, molluscs and seaweed accumulation. Swimming and other aquatic sports are not included in the model used for dose calculations because of theirs relatively low importance in comparison with the pathways concerning ingestion of aquatic food

Nanostructural control of the release of macromolecules from silica sol–gels

Science.gov (United States)

Radin, Shula; Bhattacharyya, Sanjib; Ducheyne, Paul

2013-01-01

The therapeutic use of biological molecules such as growth factors and monoclonal antibodies is challenging in view of their limited half-life in vivo. This has elicited the interest in delivery materials that can protect these molecules until released over extended periods of time. Although previous studies have shown controlled release of biologically functional BMP-2 and TGF-β from silica sol–gels, more versatile release conditions are desirable. This study focuses on the relationship between room temperature processed silica sol–gel synthesis conditions and the nanopore size and size distribution of the sol–gels. Furthermore, the effect on release of large molecules with a size up to 70 kDa is determined. Dextran, a hydrophilic polysaccharide, was selected as a large model molecule at molecular sizes of 10, 40 and 70 kDa, as it enabled us to determine a size effect uniquely without possible confounding chemical effects arising from the various molecules used. Previously, acid catalysis was performed at a pH value of 1.8 below the isoelectric point of silica. Herein the silica synthesis was pursued using acid catalysis at either pH 1.8 or 3.05 first, followed by catalysis at higher values by adding base. This results in a mesoporous structure with an abundance of pores around 3.5 nm. The data show that all molecular sizes can be released in a controlled manner. The data also reveal a unique in vivo approach to enable release of large biological molecules: the use more labile sol–gel structures by acid catalyzing above the pH value of the isoelectric point of silica; upon immersion in a physiological fluid the pores expand to reach an average size of 3.5 nm, thereby facilitating molecular out-diffusion. PMID:23643607

Preparation and controlled release of mesoporous MCM-41/propranolol hydrochloride composite drug.

Science.gov (United States)

Zhai, Qing-Zhou

2013-01-01

This article used MCM-41 as a carrier for the assembly of propranolol hydrochloride by the impregnation method. By means of chemical analysis, powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy and low-temperature N(2) adsorption-desorption at 77 K, the characterization was made for the prepared materials. The propranolol hydrochloride guest assembly capacity was 316.20 ± 0.31 mg/g (drug/MCM-41). Powder XRD test results indicated that during the process of incorporation, the frameworks of the MCM-41 were not destroyed and the crystalline degrees of the host-guest nanocomposite materials prepared still remained highly ordered. Characterization by SEM and TEM showed that the composite material presented spherical particle and the average particle size of composite material was 186 nm. FT-IR spectra showed that the MCM-41 framework existed well in the (MCM-41)-propranolol hydrochloride composite. Low-temperature nitrogen adsorption-desorption results at 77 K showed that the guest partially occupied the channels of the molecular sieves. Results of the release of the prepared composite drug in simulated body fluid indicated that the drug can release up to 32 h and its maximum released amount was 99.20 ± 0.11%. In the simulated gastric juice release pattern of drug, the maximum time for the drug release was discovered to be 6 h and the maximum cumulative released amount of propranolol hydrochloride was 45.13 ± 0.23%. The drug sustained-release time was 10 h in simulated intestinal fluid and the maximum cumulative released amount was 62.05 ± 0.13%. The prepared MCM-41 is a well-controlled drug delivery carrier.

Ability of possible DMS precursors to release DMS during wine aging and in the conditions of heat-alkaline treatment.

Science.gov (United States)

Segurel, Marie A; Razungles, Alain J; Riou, Christophe; Trigueiro, Mafalda G L; Baumes, Raymond L

2005-04-06

The origin of dimethyl sulfide (DMS) produced during wine aging was examined through different assays. The production of DMS during the model aging of a wine and the concomitant decrease of residual potential DMS (PDMS), as DMS released by heat-alkaline treatment in 0.5 M sodium hydroxide at 100 degrees C for 1 h, were demonstrated. Then, dimethyl sulfoxide (DMSO), methionine sulfoxide (MSO), S-methylmethionine (SMM), and dimethylsulfonium propanoic acid (DMSPA), reported previously as possible DMS precursors, were investigated for their ability to be DMS precursors in wine in the conditions of this model aging and of the heat-alkaline treatment. The results showed that DMSO, MSO, and DMSPA could hardly be DMS precursors in the conditions used, whereas SMM appeared to be a good candidate. Finally, the use of [(2)H(6)]-DMSPA as an internal standard for PDMS determination was proposed, because it provided better reproducibility than [(2)H(6)]-DMS used as an external standard.

Use of cyclodextrins as a cosmetic delivery system for fragrance materials: linalool and benzyl acetate.

Science.gov (United States)

Numanoğlu, Ulya; Sen, Tangül; Tarimci, Nilüfer; Kartal, Murat; Koo, Otilia M Y; Onyüksel, Hayat

2007-10-19

The aim of this study was to increase the stability and water solubility of fragrance materials, to provide controlled release of these compounds, and to convert these substances from liquid to powder form by preparing their inclusion complexes with cyclodextrins (CDs). For this purpose, linalool and benzyl acetate were chosen as the fragrance materials. The use of beta-cyclodextrin (beta CD) and 2-hydroxypropyl-beta-cyclodextrin (2-HP beta CD) for increasing the solubility of these 2 fragrance materials was studied. Linalool and benzyl acetate gave a B-type diagram with beta CD, whereas they gave an A(L)-type diagram with 2-HP beta CD. Therefore, complexes of fragrance materials with 2-HP beta CD at 1:1 and 1:2 molar ratios (guest:host) were prepared. The formation of inclusion complexes was confirmed using proton nuclear magnetic resonance ((1)H-NMR) spectroscopy and circular dichroism spectroscopy. The results of the solubility studies showed that preparing the inclusion complex with 2-HP beta CD at a 1:1 molar ratio increased the solubility of linalool 5.9-fold and that of benzyl acetate 4.2-fold, whereas the complexes at a 1:2 molar ratio increased the solubility 6.4- and 4.5-fold for linalool and benzyl acetate, respectively. The stability and in vitro release studies were performed on the gel formulations prepared using uncomplexed fragrance materials or inclusion complexes of fragrance materials at a 1:1 molar ratio. It was observed that the volatility of both fragrance materials was decreased by preparing the inclusion complexes with 2-HP beta CD. Also, in vitro release data indicated that controlled release of fragrances could be possible if inclusion complexes were prepared.

Release of alpha emitters into the environment by Nuclear Industries of Brazil in Resende, RJ

International Nuclear Information System (INIS)

Pereira, Wagner S.; Kelecom, Alphonse; Santos, Rodney; Santos, Maisa F.M.; Torres, Vinicius R.M.; Rodrigues, Jéssica J.S.; Universidade Veiga de Almeida; Universidade Federal Fluminense

2017-01-01

The Nuclear Industries of Brazil operates in the field of nuclear energy and has a monopoly on mining and manufacturing the nuclear fuel element in Brazil. The Nuclear Fuel Factory is also responsible for the reconversion process, the manufacture of the pellets and the assembly of the fuel element. Once there is a possibility of particulate material generation during the reconversion processes and the manufacture of pellets, a method of collective protection of the worker was established, which includes a system of air exhaustion of the factory area, with the capacity to renew the indoor air six times per hour. As a control measure, there is a system of automatic detection of the release of radionuclides in the chimney that monitors and calculates the released values. Through the dose calculation model established by the National Commission for Nuclear Energy the release limit is fixed at 1.2∙ 10"7Bq.y"-"1 of alpha emitters by FCN. The present work aims to evaluate the alpha radionuclides released by FCN, in terms of total release (Bq) and Activity Concentration (AC, mBq∙m"-"3). In 2016 it was released 4.14∙10"6Bq.y"-"1, which means an average of 3.45∙10"5Bq.month"-"1. The largest mean for AC was 4.03 mBq∙m"-"3. The release data was almost an order of magnitude lower than the annual release limit, proving the suitability of the atmospheric effluents to the licensing requirements. The largest magnitudes of the two variables (AC and release) were observed in August while the smallest ones, in January. (author)

Release of alpha emitters into the environment by Nuclear Industries of Brazil in Resende, RJ

Energy Technology Data Exchange (ETDEWEB)