Winter Storm Jupiter of January 2017: Meteorological Drivers, Synoptic Evolution, and Climate Change Considerations in Portland, Oregon

Science.gov (United States)

Dean, S.; Loikith, P. C.

2017-12-01

Although the Pacific Northwest has some of the highest wintertime precipitation in the United States, most urban areas receive little in the way of snow. While 37 inches of wintertime rain fall in Portland on average annually, the city only receives four inches of snow on average. Although wintertime extreme snowstorm events are rare in Portland, in the last century they have occurred about once every ten years. On January 10-12th, 2017, winter storm Jupiter brought 11 inches of snow to downtown Portland within a 12-hour period, making it the largest snowstorm for the city in twenty years. The city declared a state of emergency, over 30,000 citizens lost power, and thousands of businesses were forced to shut down. The anomalously cold air and high amounts of snowfall in a short amount of time made the storm different from others in recent years. This study aims to discover the meteorological drivers behind the January 2017 snowstorm in Portland, Oregon. We also aim to understand how this storm compared with other local storms in the past, and assess the likelihood of a similar event occurring in the future. To do this, reanalysis data were used to display the synoptic evolution of the January 2017 storm. We compared this storm with two other extreme snowfall events from December 2008 and January 1980, assessing meteorological similarities and differences between storms. Results show that the 2017 event was associated with a slow moving, strong low-pressure system accompanied by a 500 hPa trough. These large-scale features helped drive slow moving, locally heavy snow bands over the city of Portland. At the same time, an unusually strong Arctic high-pressure system moved into the interior Pacific Northwest allowing for strong cold air advection west through the Cascade Mountain Range and Columbia River Gorge. Temperature trends show warming of 1-2 °C in the Pacific Northwest since the middle of the last century. Because of this, uncertainty associated with

2014 Metro, Oregon 4-Band 8 Bit Imagery

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — These data are LiDAR orthorectified aerial photographs (8-bit GeoTIFF format) within the Oregon Lidar Consortium Portland project area. The imagery coverage is...

The Social Acceptance of Community Solar: A Portland Case Study

Science.gov (United States)

Weaver, Anne

Community solar is a renewable energy practice that's been adopted by multiple U.S. states and is being considered by many more, including the state of Oregon. A recent senate bill in Oregon, called the "Clean Electricity and Coal Transition Plan", includes a provision that directs the Oregon Public Utility Commission to establish a community solar program for investor-owned utilities by late 2017. Thus, energy consumers in Portland will be offered participation in community solar projects in the near future. Community solar is a mechanism that allows ratepayers to experience both the costs and benefits of solar energy while also helping to offset the proportion of fossil-fuel generated electricity in utility grids, thus aiding climate change mitigation. For community solar to achieve market success in the residential sector of Portland, ratepayers of investor-owned utilities must socially accept this energy practice. The aim of this study was to forecast the potential social acceptance of community solar among Portland residents by measuring willingness to participate in these projects. Additionally, consumer characteristics, attitudes, awareness, and knowledge were captured to assess the influence of these factors on intent to enroll in community solar. The theory of planned behavior, as well as the social acceptance, diffusion of innovation, and dual-interest theories were frameworks used to inform the analysis of community solar adoption. These research objectives were addressed through a mixed-mode survey of Portland residents, using a stratified random sample of Portland neighborhoods to acquire a gradient of demographics. 330 questionnaires were completed, yielding a 34.2% response rate. Descriptive statistics, binomial logistic regression models, and mean willingness to pay were the analyses conducted to measure the influence of project factors and demographic characteristics on likelihood of community solar participation. Roughly 60% of respondents

Lithofacies and petrophysical properties of Portland Base Bed and Portland Whit Bed limestone as related to durability

NARCIS (Netherlands)

Dubelaar, C.W.; Engering, S.; Hees, R.P.J. van; Koch, R.; Lorenz, H.G.

2003-01-01

This study focuses on the differences in lithofacies and petrophysical properties of Base Bed and Whit Bed Portland limestone and the presumed relationships between these characteristics and the durability of this building stone. As Portland limestone probably will be used as a stone for several

Lithofacies and Petrophysical Properties of Portland Base Bed and Portland Whit Bed Limestone as Related to Durability

NARCIS (Netherlands)

Dubelaar, C.W.; Engering, S.; Van Hees, R.P.J.; Koch, R.; Lorenz, H.G.

2003-01-01

This study focuses on the differences in lithofacies and petrophysical properties of Base Bed and Whit Bed Portland limestone and the presumed relationships between these characteristics and the durability of this building stone. As Portland limestone probably will be used as a stone for several

NW Oregon radon potential based on soil radionuclides

International Nuclear Information System (INIS)

Ashbaugh, S.G.; Burns, S.F.

1993-01-01

Analysis of soil by gamma spectroscopy for Bi-214 (Ra-226) suggests low to moderate radon potentials for northwest Oregon in areas with low to moderate soil permeabilities. Very low radon potential zones (0.2 to 0.7 pCi/g) comprise 58% of the study area. These zones are frequently associated with soils developed from undifferentiated basalts and andesites of the Cascade Range, and basalts and undifferentiated mafic intrusives of the Coast Range. Low radon potential zones (0.7 to 1.2 pCi/g) comprise 28% of the study area. These zones are generally associated with Missoula Flood sediments, pre-Holocene loess in the Portland area, and Eocene/Oligocene marine sediments low in mica and/or tuff along the foothills of the Willamette Valley. Moderate radon potential zones (1.2 to 3.0 pCi/g) comprise 14% of the study area. These zones are often associated with the lateritic soils derived from Columbia River Basalts and Eocene/Oligocene marine sediments high in mica and/or tuff along the western edges of the Willamette Valley. A closer examination of soils in the Portland and Salem areas shows that: (1) Bi-214/K-40 ratios increase from 0.07 to 0.35 with respect to solid development, indicating K-40 to be preferentially leached over Ra-226; (2) clay development within B-horizons does not reflect a significant increase in Ra-226 mobility; and (3) elevated indoor radon within the Portland and Salem areas can be attributed to high soil permeabilities rather than soil chemistry

2007 Oregon Department of Geology and Mineral Industries (DoGAMI) LiDAR: Northwest Oregon and Portland Metro Area

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Watershed Sciences, Inc. collected Light Detection and Ranging (LiDAR) data for the Oregon Department of Geology and Mineral Industries (DoGAMI) and the Oregon...

Occupational Contact Dermatitis: Workers' Compensation Patch Test Results of Portland, Oregon, 2005-2014.

Science.gov (United States)

Coman, Garrett; Zinsmeister, Chris; Norris, Patricia

2015-01-01

Workers are exposed to potential irritants and allergens with constant introduction of new industrial chemicals in the workplace. Characterize the final diagnoses, demographics, occupations, exposures, clinical presentations, patch test results, dermatologic histories, and risk factors of workers evaluated for suspected work-related allergic contact dermatitis (ACD). A retrospective chart review of 310 workers' compensation independent medical examinations evaluated for suspected work-related ACD was performed. Workers were seen in a community dermatology clinic in Portland, Oregon, from 2005 to 2014. Evaluation included history, physical examination, patch testing, and further diagnostic workup when indicated. Hand dermatitis was the most common presentation (n = 148, 47.7%). Prevalent occupations included health care workers (n = 51, 16.5%), custodial staff (n = 41, 13.2%), and machinists (n = 36, 11.6%). Allergic contact dermatitis (47.5%) was more common than irritant contact dermatitis (ICD) (38.9%) in those diagnosed as having occupational skin disease (n = 185). The highest-frequency work-related allergens were thiuram mix (21 of 88, 23.9%), carba mix (20 of 88, 22.7%), potassium dichromate (9 of 88, 10.2%), and epoxy resin (9 of 88, 10.2%). Allergic contact dermatitis and ICD are common occupational skin disorders. In this population of workers' compensation referrals, ACD was more common, with 73.3% of those cases work related, compared with 86.7% of ICD. Blue collar work and wet work were risk factors for the development of ACD and ICD.

Clean Energy Works Oregon Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Jacob, Andria [City of Portland; Cyr, Shirley [Clean Energy Works

2013-12-31

In April 2010, the City of Portland received a $20 million award from the U.S. Department of Energy, as part of the Energy Efficiency and Conservation Block Grant program. This award was appropriated under the American Recovery and Reinvestment Act (ARRA), passed by President Obama in 2009. DOE’s program became known as the Better Buildings Neighborhood Program (BBNP). The BBNP grant objectives directed the City of Portland Bureau of Planning and Sustainability (BPS) as the primary grantee to expand the BPS-led pilot program, Clean Energy Works Portland, into Clean Energy Works Oregon (CEWO), with the mission to deliver thousands of home energy retrofits, create jobs, save energy and reduce carbon dioxide emissions.The Final Technical Report explores the successes and lessons learned from the first 3 years of program implementation.

Combining Ordinary Kriging with wind directions to identify sources of industrial odors in Portland, Oregon.

Science.gov (United States)

Eckmann, Ted C; Wright, Samantha G; Simpson, Logan K; Walker, Joe L; Kolmes, Steven A; Houck, James E; Velasquez, Sandra C

2018-01-01

This study combines Ordinary Kriging, odor monitoring, and wind direction data to demonstrate how these elements can be applied to identify the source of an industrial odor. The specific case study used as an example of how to address this issue was the University Park neighborhood of Portland, Oregon (USA) where residents frequently complain about industrial odors, and suspect the main source to be a nearby Daimler Trucks North America LLC manufacturing plant. We collected 19,665 odor observations plus 105,120 wind measurements, using an automated weather station to measure winds in the area at five-minute intervals, logging continuously from December 2014 through November 2015, while we also measured odors at 19 locations, three times per day, using methods from the American Society of the International Association for Testing and Materials. Our results quantify how winds vary with season and time of day when industrial odors were observed versus when they were not observed, while also mapping spatiotemporal patterns in these odors using Ordinary Kriging. Our analyses show that industrial odors were detected most frequently to the northwest of the Daimler plant, mostly when winds blew from the southeast, suggesting Daimler's facility is a likely source for much of this odor.

78 FR 4381 - Foreign-Trade Zone 45-Portland, Oregon; Application for Reorganization and Expansion Under...

Science.gov (United States)

2013-01-22

... following sites: Site 1 (1,830 acres)--Rivergate Industrial Park, Port Terminal Nos. 5 and 6, and the... Way and NE Alderwood Road, Portland; Site 3 (254 acres)--Portland Ship Repair Yard, 5555 N. Channel...

Annual Review of BPA-Funded Projects in Natural and Artificial Propagation of Salmonids, March 27-29, 1985, Holiday Inn Airport, Portland, Oregon.

Energy Technology Data Exchange (ETDEWEB)

United States. Bonneville Power Administration.

1985-04-01

The Fish and Wildlife Division of Bonneville Power Administration (BPA) hosted a meeting for contractors to present the results of fiscal year 1984 research conducted to implement the Northwest Power Planning Council's Fish and Wildlife Program. The meeting focused on those projects specifically related to natural and artificial propagation of salmonids. The presentations were held at the Holiday Inn Airport in Portland, Oregon, on March 27-29, 1985. This document contains abstracts of the presentations from that meeting. Section 1 contains abstracts on artificial propagation, fish health, and downstream migration, and Section 2 contains abstracts on natural propagation and habitat improvement. The abstracts are indexed by BPA Project Number and by Fish and Wildlife Program Measure. The registered attendees at the meeting are listed alphabetically in Appendix A and by affiliation in Appendix B.

Immobilisation Of Spent Ion Exchange Resins Using Portland Cement Blending With Organic Material

International Nuclear Information System (INIS)

Zalina Laili; Mohd Abdul Wahab; Nur Azna Mahmud

2014-01-01

Immobilisation of spent ion exchange resins (spent resins) using Portland cement blending with organic material for example bio char was investigated. The performance of cement-bio char matrix for immobilisation of spent ion exchange resins was evaluated based on their compression strength and leachability under different experimental conditions. The results showed that the amount of bio char and spent resins loading effect the compressive strength of the waste form. Several factors affecting the leaching behaviour of immobilised spent resins in cement-bio char matrix. (author)

The Portland Basin: A (big) river runs through it

Science.gov (United States)

Evarts, Russell C.; O'Connor, Jim E.; Wells, Ray E.; Madin, Ian P.

2009-01-01

Metropolitan Portland, Oregon, USA, lies within a small Neogene to Holocene basin in the forearc of the Cascadia subduction system. Although the basin owes its existence and structural development to its convergent-margin tectonic setting, the stratigraphic architecture of basin-fill deposits chiefly reflects its physiographic position along the lower reaches of the continental-scale Columbia River system. As a result of this globally unique setting, the basin preserves a complex record of aggradation and incision in response to distant as well as local tectonic, volcanic, and climatic events. Voluminous flood basalts, continental and locally derived sediment and volcanic debris, and catastrophic flood deposits all accumulated in an area influenced by contemporaneous tectonic deformation and variations in regional and local base level.

Beyond a Box of Documents: The Collaborative Partnership Behind the Oregon Chinese Disinterment Documents Collection

Directory of Open Access Journals (Sweden)

Natalia M. Fernández

2013-06-01

Full Text Available This article is a case study of a collaboration between the Oregon Multicultural Archives of Oregon State University, Portland State University Library's Special Collections, the Chinese Consolidated Benevolent Association (CCBA, and the Northwest News Network to preserve and make accessible a recovered box of Oregon Chinese disinterment documents. By examining what influenced and engaged each partner, this case study offers an opportunity to better understand the motivations of diverse stakeholders in a "post-custodial era" project that challenges traditional practices of custody, control, and access.

76 FR 7853 - Patient Safety Organizations: Voluntary Delisting From Oregon Patient Safety Commission

Science.gov (United States)

2011-02-11

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Agency for Healthcare Research and Quality Patient Safety Organizations: Voluntary Delisting From Oregon Patient Safety Commission AGENCY: Agency for Healthcare Research and Quality (AHRQ), HHS. ACTION: Notice of delisting. SUMMARY: Oregon Patient Safety Commission: AHRQ...

Controlling Mitochondrial Dynamics to Mitigate Noise-Induced Hearing Loss

Science.gov (United States)

2017-10-01

Alfred L. Nuttall CONTRACTING ORGANIZATION: Oregon Health & Science University Portland, OR 97201 REPORT DATE: October 2017 TYPE OF REPORT: Annual...ohsu.edu 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT NUMBER Oregon Health & Science...based upon the results of these studies, we have also examined additional concentrations of mdivi-1 and performed a multiple-day (5 days) mdivi-1

Mesenchymal Stem Cells for the Prevention of Acute Respiratory Distress Syndrome after Pulmonary Contusion and Hemorrhagic Shock

Science.gov (United States)

2017-10-01

Contusion and Hemorrhagic Shock PRINCIPAL INVESTIGATOR: Martin Schreiber, MD CONTRACTING ORGANIZATION: Oregon Health & Science University Portland, OR...PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Oregon Health & Science University 3181 SW Sam Jackson Park Road, Portland, OR 97239 Blood Systems...extubated the animals was not logistically or physically feasible. To improve the welfare of the animal and consistency in the model, we revised our model

Investigating organic matter in Fanno Creek, Oregon, Part 1 of 3: estimating annual foliar biomass for a deciduous-dominant urban riparian corridor

Science.gov (United States)

Sobieszczyk, Steven; Keith, Mackenzie K.; Rounds, Stewart A.; Goldman, Jami H.

2014-01-01

For this study, we explored the amount, type, and distribution of foliar biomass that is deposited annually as leaf litter to Fanno Creek and its floodplain in Portland, Oregon, USA. Organic matter is a significant contributor to the decreased dissolved oxygen concentrations observed in Fanno Creek each year and leaf litter is amongst the largest sources of organic matter to the stream channel and floodplain. Using a combination of field measurements and light detection and ranging (LiDAR) point cloud data, the annual foliar biomass was estimated for 13 stream reaches along the creek. Biomass estimates were divided into two sets: (1) the annual foliage available from the entire floodplain overstory canopy, and (2) the annual foliage overhanging the stream, which likely contributes leaf litter directly to the creek each year. Based on these computations, an estimated 991 (±22%) metric tons (tonnes, t) of foliar biomass is produced annually above the floodplain, with about 136 t (±24%) of that foliage falling directly into Fanno Creek. The distribution of foliar biomass varies by reach, with between 150 and 640 t/km2 produced along the floodplain and between 400 and 1100 t/km2 available over the channel. Biomass estimates vary by reach based primarily on the density of tree cover, with forest-dominant reaches containing more mature deciduous trees with broader tree canopies than either wetland or urban-dominant reaches, thus supplying more organic material to the creek. By quantifying the foliar biomass along Fanno Creek we have provided a reach-scale assessment of terrestrial organic matter loading, thereby providing land managers useful information for planning future restoration efforts.

Symmetry or asymmetry -- Comfort is the question. (A study of the second floor of the west office wing of the Water Pollution Control Laboratory in Portland, Oregon.)

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, A.F.; Gaba, P.; Kowitanupong, C.

1999-07-01

This article explores the effects of an asymmetric distribution of building components, and their relation to human comfort. The studied building was the Water Pollution Control Laboratory in Portland, Oregon. This project, designed by the Miller/Hull Partnership, provides the perfect conditions to do such a study since it has very different ceiling heights within the same space, and an asymmetric distribution of the fenestration as well. Findings show that: (a) Variable ceiling heights affect the quantity of daylight received, and also affect the quality and distribution of electric light; (b) An asymmetric distribution of the fenestration creates very different conditions in both the luminous and thermal environments; and (c) The design of lighting and HVAC systems must take into consideration variations in ceiling height and the position of the fenestration into the space.

Comparative Study of Portland Cement-based and Zeolite-based Concretes in Terms of Hexavalent Chromium Leaching

Directory of Open Access Journals (Sweden)

Oravec Jozef

2016-12-01

Full Text Available The paper presents the results of the leaching study of Portland cement-based and zeolite-based concretes regarding water soluble hexavalent chromium. Three leaching water media (distilled water, rain water, and Britton-Robinson buffer of various pH values were under investigation. The correlation between pH and leached-out concentrations of chromium was not confirmed. The content of hexavalent water-soluble chromium in leachates of zeolite-based concretes was found to be higher than that in leachates of Portland cement-based samples.

Modeling the degradation of Portland cement pastes by biogenic organic acids

International Nuclear Information System (INIS)

De Windt, Laurent; Devillers, Philippe

2010-01-01

Reactive transport models can be used to assess the long-term performance of cement-based materials subjected to biodegradation. A bioleaching test (with Aspergillus niger fungi) applied to ordinary Portland cement pastes during 15 months is modeled with HYTEC. Modeling indicates that the biogenic organic acids (acetic, butyric, lactic and oxalic) strongly accelerate hydrate dissolution by acidic hydrolysis whilst their complexation of aluminum has an effect on the secondary gel stability only. The deepest degradation front corresponds to portlandite dissolution and decalcification of calcium silicate hydrates. A complex pattern of sulfate phases dissolution and precipitation takes place in an intermediate zone. The outermost degraded zone consists of alumina and silica gels. The modeling accurateness of calcium leaching, pH evolution and degradation thickness is consistently enhanced whilst considering increase of diffusivity in the degraded zones. Precipitation of calcium oxalate is predicted by modeling but was hindered in the bioleaching reactor.

Radiopacity evaluation of Portland and MTA-based cements by digital radiographic system.

Science.gov (United States)

Borges, Alvaro Henrique; Pedro, Fabio Luiz Miranda; Semanoff-Segundo, Alex; Miranda, Carlos Eduardo Saraiva; Pécora, Jesus Djalma; Cruz Filho, Antônio Miranda

2011-01-01

The aim of the present study was to evaluate the radiopacity of Portland and MTA-based cements using the Digora TM digital radiographic system. The performed tests followed specification number 57 from the American National Standard Institute/American Dental Association (2000) for endodontic sealing materials. The materials were placed in 5 acrylic plates, especially designed for this experiment, along with a graduated aluminum stepwedge varying from 1 to 10 mm in thickness. The set was radiographed at a 30 cm focus-object distance and with 0.2 s exposure time. After the radiographs were taken, the optical laser readings of radiographs were performed by Digora TM system. Five radiographic density readings were performed for each studied material and for each step of the aluminum scale. White ProRoot MTA (155.99±8.04), gray ProRoot MTA (155.96±16.30) and MTA BIO (143.13±16.94) presented higher radiopacity values (pPortland (119.76±22.34), gray Portland (109.71±4.90) and white structural Portland (99.59±12.88) presented lower radiopacity values (pcements were the only materials presenting radiopacity within the ANSI/ADA specifications.

Network Level Carbon Dioxide Emissions From On-road Sources in the Portland OR, (USA) Metropolitan Area

Science.gov (United States)

Powell, J.; Butenhoff, C. L.; Rice, A. L.

2014-12-01

To mitigate climate change, governments at multiple levels are developing policies to decrease anthropogenic carbon dioxide (CO2) emissions. The City of Portland (Oregon) and Multnomah County have adopted a Climate Action Plan with a stated goal of reducing emissions to 80% below 1990 levels by 2050. The transportation sector alone accounts for about 40% of total emissions in the Portland metropolitan area. Here we show a new street-level model of on-road mobile CO2 emissions for the Portland, OR metropolitan region. The model uses hourly traffic counter recordings made by the Portland Bureau of Transportation at 9,352 sites over 21 years (1986-2006), augmented with freeway loop detector data from the Portland Regional Transportation Archive Listing (PORTAL) transportation data archive. We constructed a land use regression model to fill in traffic network gaps with traffic counts as the dependent variable using GIS data such as road class (32 categories) and population density. The Environmental Protection Agency (EPA) MOtor Vehicle Emission Simulator (MOVES) model was used to estimate transportation CO2 emissions. The street-level emissions can be aggregated and gridded and used as input to atmospheric transport models for comparison with atmospheric measurements. This model also provides an independent assessment of top-down inventories that determine emissions from fuel sales, while being an important component of our ongoing effort to assess the effectiveness of emission mitigation strategies at the urban scale.

77 FR 15263 - Security Zone; Portland Rose Festival on Willamette River; Portland, OR

Science.gov (United States)

2012-03-15

... Zone; Portland Rose Festival on Willamette River; Portland, OR AGENCY: Coast Guard, DHS. ACTION: Notice of enforcement of regulation. SUMMARY: The Coast Guard will enforce the Portland Rose Festival... Willamette River during the Portland Rose festival. During the enforcement period, no person or vessel may...

Coordinated Care Organizations: Neonatal and Infant Outcomes in Oregon.

Science.gov (United States)

Harvey, S Marie; Oakley, Lisa P; Yoon, Jangho; Luck, Jeff

2017-11-01

In 2012, Oregon's Medicaid program implemented a comprehensive accountable care model delivered through coordinated care organizations (CCOs). Because CCOs are expected to improve utilization of services and health outcomes, neonatal and infant outcomes may be important indicators of their impact. Estimating difference-in-differences models, we compared prepost CCO changes in outcomes (e.g., low birth weight, abnormal conditions, 5-minute Apgar score, congenital anomalies, and infant mortality) between Medicaid and non-Medicaid births among 99,924 infants born in Oregon during 2011 and 2013. We further examined differences in the impact of CCOs by ethnicity and rurality. Following CCO implementation the likelihood of low birth weight and abnormal conditions decreased by 0.95% and 1.08%, a reduction of 13.4% and 10.4% compared with the pre-CCO level for Medicaid enrollees, respectively. These reductions could be predictive of lifelong health benefits for infants and lower costs for acute care and are, therefore, important markers of success for the CCO model.

Landslide inventory for the Little North Santiam River Basin, Oregon

Science.gov (United States)

Sobieszczyk, Steven

2010-01-01

This geodatabase is an inventory of existing landslides in the Little North Santiam River Basin, Oregon (2009). Each landslide feature shown has been classified according to a number of specific characteristics identified at the time recorded in the GIS database. The classification scheme was developed by the Oregon Department of Geology and Mineral Industries (Burns and Madin, 2009). Several significant landslide characteristics recorded in the database are portrayed with symbology on this map. The specific characteristics shown for each landslide are the activity of landsliding, landslide features, deep or shallow failure, type of landslide movement, and confidence of landslide interpretation. These landslide characteristics are determined primarily on the basis of geomorphic features, or landforms, observed for each landslide. This work was completed as part of the Master's thesis "Turbidity Monitoring and LiDAR Imagery Indicate Landslides are Primary Source of Suspended-Sediment Load in the Little North Santiam River Basin, Oregon, Winter 2009-2010" by Steven Sobieszczyk, Portland State University and U.S. Geological Survey. Data layers in this geodatabase include: landslide deposit boundaries (Deposits); field-verfied location imagery (Photos); head scarp or scarp flanks (Scarp_Flanks); and secondary scarp features (Scarps).The geodatabase template was developed by the Oregon Department of Geology and Mineral Industries (Burns and Madin, 2009).

Oregon's Coordinated Care Organizations and Their Effect on Prenatal Care Utilization Among Medicaid Enrollees.

Science.gov (United States)

Oakley, Lisa P; Harvey, S Marie; Yoon, Jangho; Luck, Jeff

2017-09-01

Introduction Previous studies indicate that inadequate prenatal care is more common among women covered by Medicaid compared with private insurance. Increasing the proportion of pregnant women who receive early and adequate prenatal care is a Healthy People 2020 goal. We examined the impact of the implementation of Oregon's accountable care organizations, Coordinated Care Organizations (CCOs), for Medicaid enrollees, on prenatal care utilization among Oregon women of reproductive age enrolled in Medicaid. Methods Using Medicaid eligibility data linked to unique birth records for 2011-2013, we used a pre-posttest treatment-control design that compared prenatal care utilization for women on Medicaid before and after CCO implementation to women never enrolled in Medicaid. Additional stratified analyses were conducted to explore differences in the effect of CCO implementation based on rurality, race, and ethnicity. Results After CCO implementation, mothers on Medicaid had a 13% increase in the odds of receiving first trimester care (OR 1.13, CI 1.04, 1.23). Non-Hispanic (OR 1.20, CI 1.09, 1.32), White (OR 1.20, CI 1.08, 1.33) and Asian (OR 2.03, CI 1.26, 3.27) women on Medicaid were more likely to receive initial prenatal care in the first trimester after CCO implementation and only Medicaid women in urban areas were more likely (OR 1.14, CI 1.05, 1.25) to initiate prenatal care in the first trimester. Conclusion Following Oregon's implementation of an innovative Medicaid coordinated care model, we found that women on Medicaid experienced a significant increase in receiving timely prenatal care.

Oregon's Coordinated Care Organizations Increased Timely Prenatal Care Initiation And Decreased Disparities.

Science.gov (United States)

Muoto, Ifeoma; Luck, Jeff; Yoon, Jangho; Bernell, Stephanie; Snowden, Jonathan M

2016-09-01

Policies at the state and federal levels affect access to health services, including prenatal care. In 2012 the State of Oregon implemented a major reform of its Medicaid program. The new model, called a coordinated care organization (CCO), is designed to improve the coordination of care for Medicaid beneficiaries. This reform effort provides an ideal opportunity to evaluate the impact of broad financing and delivery reforms on prenatal care use. Using birth certificate data from Oregon and Washington State, we evaluated the effect of CCO implementation on the probability of early prenatal care initiation, prenatal care adequacy, and disparities in prenatal care use by type of insurance. Following CCO implementation, we found significant increases in early prenatal care initiation and a reduction in disparities across insurance types but no difference in overall prenatal care adequacy. Oregon's reforms could serve as a model for other Medicaid and commercial health plans seeking to improve prenatal care quality and reduce disparities. Project HOPE—The People-to-People Health Foundation, Inc.

Large-scale Meteorological Patterns Associated with Extreme Precipitation Events over Portland, OR

Science.gov (United States)

Aragon, C.; Loikith, P. C.; Lintner, B. R.; Pike, M.

2017-12-01

Extreme precipitation events can have profound impacts on human life and infrastructure, with broad implications across a range of stakeholders. Changes to extreme precipitation events are a projected outcome of climate change that warrants further study, especially at regional- to local-scales. While global climate models are generally capable of simulating mean climate at global-to-regional scales with reasonable skill, resiliency and adaptation decisions are made at local-scales where most state-of-the-art climate models are limited by coarse resolution. Characterization of large-scale meteorological patterns associated with extreme precipitation events at local-scales can provide climatic information without this scale limitation, thus facilitating stakeholder decision-making. This research will use synoptic climatology as a tool by which to characterize the key large-scale meteorological patterns associated with extreme precipitation events in the Portland, Oregon metro region. Composite analysis of meteorological patterns associated with extreme precipitation days, and associated watershed-specific flooding, is employed to enhance understanding of the climatic drivers behind such events. The self-organizing maps approach is then used to characterize the within-composite variability of the large-scale meteorological patterns associated with extreme precipitation events, allowing us to better understand the different types of meteorological conditions that lead to high-impact precipitation events and associated hydrologic impacts. A more comprehensive understanding of the meteorological drivers of extremes will aid in evaluation of the ability of climate models to capture key patterns associated with extreme precipitation over Portland and to better interpret projections of future climate at impact-relevant scales.

Ultrafine portland cement performance

Directory of Open Access Journals (Sweden)

C. Argiz

2018-04-01

Full Text Available By mixing several binder materials and additions with different degrees of fineness, the packing density of the final product may be improved. In this work, ultrafine cement and silica fume mixes were studied to optimize the properties of cement-based materials. This research was performed in mortars made of two types of cement (ultrafine Portland cement and common Portland cement and two types of silica fume with different particle-size distributions. Two Portland cement replacement ratios of 4% and 10% of silica fume were selected and added by means of a mechanical blending method. The results revealed that the effect of the finer silica fume mixed with the coarse cement enhances the mechanical properties and pore structure refinement at a later age. This improvement is somewhat lower in the case of ultrafine cement with silica fume.

Costs and benefits of bicycling investments in Portland, Oregon.

Science.gov (United States)

Gotschi, Thomas

2011-01-01

Promoting bicycling has great potential to increase overall physical activity; however, significant uncertainty exists with regard to the amount and effectiveness of investment needed for infrastructure. The objective of this study is to assess how costs of Portland's past and planned investments in bicycling relate to health and other benefits. Costs of investment plans are compared with 2 types of monetized health benefits, health care cost savings and value of statistical life savings. Levels of bicycling are estimated using past trends, future mode share goals, and a traffic demand model. By 2040, investments in the range of $138 to $605 million will result in health care cost savings of $388 to $594 million, fuel savings of $143 to $218 million, and savings in value of statistical lives of $7 to $12 billion. The benefit-cost ratios for health care and fuel savings are between 3.8 and 1.2 to 1, and an order of magnitude larger when value of statistical lives is used. This first of its kind cost-benefit analysis of investments in bicycling in a US city shows that such efforts are cost-effective, even when only a limited selection of benefits is considered.

Planning, zoning and financial incentives for ecoroofs in Portland, Oregon

Energy Technology Data Exchange (ETDEWEB)

Liptan, T. [City of Portland, OR (United States). Bureau of Environmental Services

2003-07-01

Approximately 35 to 90 per cent of the surface area of various city neighbourhoods is composed of rooftops and pavement. The City of Portland has suffered from several infrastructure and environmental problems as a result of these rooftops and pavement. In response, the City created a program to address storm water related problems and to provide other environmental benefits. This program promotes the use of Ecoroofs or vegetated roofs. City officials are investigating three specific concerns regarding Ecoroofs: (1) the extent to which Ecoroofs can manage precipitation and water quality, (2) the design, construction and maintenance issues to be addressed in order to ensure Ecoroofs are viable, and (3) the policies and economic concerns that must be addressed to determine the appropriate incentives and potential regulations for Ecoroofs. The overall city program was described in this presentation. The incentives and assistance provided by the city were reviewed, and the practical lessons learned were discussed. 1 tab., 1 fig.

Landslide deposit boundaries for the Little North Santiam River Basin, Oregon

Science.gov (United States)

Sobieszczyk, Steven

2010-01-01

This layer is an inventory of existing landslides deposits in the Little North Santiam River Basin, Oregon (2009). Each landslide deposit shown on this map has been classified according to a number of specific characteristics identified at the time recorded in the GIS database. The classification scheme was developed by the Oregon Department of Geology and Mineral Industries (Burns and Madin, 2009). Several significant landslide characteristics recorded in the database are portrayed with symbology on this map. The specific characteristics shown for each landslide are the activity of landsliding, landslide features, deep or shallow failure, type of landslide movement, and confidence of landslide interpretation. These landslide characteristics are determined primarily on the basis of geomorphic features, or landforms, observed for each landslide. This work was completed as part of the Master's thesis "Turbidity Monitoring and LiDAR Imagery Indicate Landslides are Primary Source of Suspended-Sediment Load in the Little North Santiam River Basin, Oregon, Winter 2009-2010" by Steven Sobieszczyk, Portland State University and U.S. Geological Survey.Data layers in this geodatabase include: landslide deposit boundaries (Deposits); field-verfied location imagery (Photos); head scarp or scarp flanks (Scarp_Flanks); and secondary scarp features (Scarps).The geodatabase template was developed by the Oregon Department of Geology and Mineral Industries (Burns and Madin, 2009).

75 FR 20778 - Security Zone; Portland Rose Festival Fleet Week, Willamette River, Portland, OR

Science.gov (United States)

2010-04-21

...-AA87 Security Zone; Portland Rose Festival Fleet Week, Willamette River, Portland, OR AGENCY: Coast... during the Portland Rose Festival Fleet Week from June 2, 2010, through June 7, 2010. The security zone... is a need to provide a security zone for the 2010 Portland Rose Festival Fleet Week, and there is...

Field-trip guide to Mount Hood, Oregon, highlighting eruptive history and hazards

Science.gov (United States)

Scott, William E.; Gardner, Cynthia A.

2017-06-22

This guidebook describes stops of interest for a geological field trip around Mount Hood volcano. It was developed for the 2017 International Association of Volcanology and Chemistry of the Earth’s Interior (IAVCEI) Scientific Assembly in Portland, Oregon. The intent of this guidebook and accompanying contributions is to provide an overview of Mount Hood, including its chief geologic processes, magmatic system, eruptive history, local tectonics, and hazards, by visiting a variety of readily accessible localities. We also describe coeval, largely monogenetic, volcanoes in the region. Accompanying the field-trip guidebook are separately authored contributions that discuss in detail the Mount Hood magmatic system and its products and behavior (Kent and Koleszar, this volume); Mount Hood earthquakes and their relation to regional tectonics and the volcanic system (Thelen and Moran, this volume); and young surface faults cutting the broader Mount Hood area whose extent has come to light after acquisition of regional light detection and ranging coverage (Madin and others, this volume).The trip makes an approximately 175-mile (280-kilometer) clockwise loop around Mount Hood, starting and ending in Portland. The route heads east on Interstate 84 through the Columbia River Gorge National Scenic Area. The guidebook points out only a few conspicuous features of note in the gorge, but many other guides to the gorge are available. The route continues south on the Mount Hood National Scenic Byway on Oregon Route 35 following Hood River, and returns to Portland on U.S. Highway 26 following Sandy River. The route traverses rocks as old as the early Miocene Eagle Creek Formation and overlying Columbia River Basalt Group of middle Miocene age, but chiefly lava flows and clastic products of arc volcanism of late Miocene to Holocene age.

Assessing Vulnerability to Urban Heat: A Study of Disproportionate Heat Exposure and Access to Refuge by Socio-Demographic Status in Portland, Oregon

Directory of Open Access Journals (Sweden)

Jackson Voelkel

2018-03-01

Full Text Available Extreme urban heat is a powerful environmental stressor which poses a significant threat to human health and well-being. Exacerbated by the urban heat island phenomenon, heat events are expected to become more intense and frequent as climate change progresses, though we have limited understanding of the impact of such events on vulnerable populations at a neighborhood or census block group level. Focusing on the City of Portland, Oregon, this study aimed to determine which socio-demographic populations experience disproportionate exposure to extreme heat, as well as the level of access to refuge in the form of public cooling centers or residential central air conditioning. During a 2014 heat wave, temperature data were recorded using a vehicle-traverse collection method, then extrapolated to determine average temperature at the census block group level. Socio-demographic factors including income, race, education, age, and English speaking ability were tested using statistical assessments to identify significant relationships with heat exposure and access to refuge from extreme heat. Results indicate that groups with limited adaptive capacity, including those in poverty and non-white populations, are at higher risk for heat exposure, suggesting an emerging concern of environmental justice as it relates to climate change. The paper concludes by emphasizing the importance of cultural sensitivity and inclusion, in combination with effectively distributing cooling centers in areas where the greatest burden befalls vulnerable populations.

Assessing Vulnerability to Urban Heat: A Study of Disproportionate Heat Exposure and Access to Refuge by Socio-Demographic Status in Portland, Oregon.

Science.gov (United States)

Voelkel, Jackson; Hellman, Dana; Sakuma, Ryu; Shandas, Vivek

2018-03-30

Extreme urban heat is a powerful environmental stressor which poses a significant threat to human health and well-being. Exacerbated by the urban heat island phenomenon, heat events are expected to become more intense and frequent as climate change progresses, though we have limited understanding of the impact of such events on vulnerable populations at a neighborhood or census block group level. Focusing on the City of Portland, Oregon, this study aimed to determine which socio-demographic populations experience disproportionate exposure to extreme heat, as well as the level of access to refuge in the form of public cooling centers or residential central air conditioning. During a 2014 heat wave, temperature data were recorded using a vehicle-traverse collection method, then extrapolated to determine average temperature at the census block group level. Socio-demographic factors including income, race, education, age, and English speaking ability were tested using statistical assessments to identify significant relationships with heat exposure and access to refuge from extreme heat. Results indicate that groups with limited adaptive capacity, including those in poverty and non-white populations, are at higher risk for heat exposure, suggesting an emerging concern of environmental justice as it relates to climate change. The paper concludes by emphasizing the importance of cultural sensitivity and inclusion, in combination with effectively distributing cooling centers in areas where the greatest burden befalls vulnerable populations.

Low-cost computer classification of land cover in the Portland area, Oregon, by signature extension techniques

Science.gov (United States)

Gaydos, Leonard

1978-01-01

Computer-aided techniques for interpreting multispectral data acquired by Landsat offer economies in the mapping of land cover. Even so, the actual establishment of the statistical classes, or "signatures," is one of the relatively more costly operations involved. Analysts have therefore been seeking cost-saving signature extension techniques that would accept training data acquired for one time or place and apply them to another. Opportunities to extend signatures occur in preprocessing steps and in the classification steps that follow. In the present example, land cover classes were derived by the simplest and most direct form of signature extension: Classes statistically derived from a Landsat scene for the Puget Sound area, Wash., were applied to the Portland area, Oreg., using data for the next Landsat scene acquired less than 25 seconds down orbit. Many features can be recognized on the reduced-scale version of the Portland land cover map shown in this report, although no statistical assessment of its accuracy is available.

OHSU web site readers have access to distinctive information. How to e-mail a child in the hospital; where to find a midwife.

Science.gov (United States)

Botvin, Judith D

2005-01-01

Oregon Health & Science University (OHSU), Portland, Ore., posts a web site which generously covers the various aspects of this complex organization. Visitors to www.osuhealth.com, can find a midwife, send an email to a child in the hospital, and learn about the benefits of living in Oregon.

Stakeholder value-linked sustainability assessment: Evaluating remedial alternatives for the Portland Harbor Superfund Site, Portland, Oregon, USA.

Science.gov (United States)

Apitz, Sabine E; Fitzpatrick, Anne G; McNally, Amanda; Harrison, David; Coughlin, Conor; Edwards, Deborah A

2018-01-01

Regulatory decisions on remediation should consider affected communities' needs and values, and how these might be impacted by remedial options; this process requires that diverse stakeholders are able to engage in a transparent consideration of value trade-offs and of the distribution of risks and benefits associated with remedial actions and outcomes. The Stakeholder Values Assessment (SVA) tool was developed to evaluate remedial impacts on environmental quality, economic viability, and social equity in the context of stakeholder values and priorities. Stakeholder values were linked to the pillars of sustainability and also to a range of metrics to evaluate how sediment remediation affects these values. Sediment remedial alternatives proposed by the US Environmental Protection Agency (USEPA) for the Portland Harbor Superfund Site were scored for each metric, based upon data provided in published feasibility study (FS) documents. Metric scores were aggregated to generate scores for each value; these were then aggregated to generate scores for each pillar of sustainability. In parallel, the inferred priorities (in terms of regional remediation, restoration, planning, and development) of diverse stakeholder groups (SGs) were used to evaluate the sensitivity and robustness of the values-based sustainability assessment to diverse SG priorities. This approach, which addresses social indicators of impact and then integrates them with indicators of environmental and economic impacts, goes well beyond the Comprehensive Environmental Response, Compensation and Liability Act's (CERCLA) 9 criteria for evaluating remedial alternatives because it evaluates how remedial alternatives might be ranked in terms of the diverse values and priorities of stakeholders. This approach identified trade-offs and points of potential contention, providing a systematic, semiquantitative, transparent valuation tool that can be used in community engagement. Integr Environ Assess Manag 2018

CERCLA-linked environmental impact and benefit analysis: Evaluating remedial alternatives for the Portland Harbor Superfund Site, Portland, Oregon, USA.

Science.gov (United States)

McNally, Amanda D; Fitzpatrick, Anne G; Mirchandani, Sera; Salmon, Matthew; Edwards, Deborah A

2018-01-01

This analysis focused on evaluating the environmental consequences of remediation, providing indicators for the environmental quality pillar of 3 "pillars" of the Portland Harbor Sustainability Project (PHSP) framework (the other 2 pillars are economic viability and social equity). The project an environmental impact and benefit analysis (EIBA) and an EIBA-based cost-benefit analysis. Metrics developed in the EIBA were used to quantify and compare remedial alternatives' environmental benefits and impacts in the human and ecological domains, as a result of remedial actions (relative to no action). The cost-benefit results were used to evaluate whether remediation costs were proportionate or disproportionate to the environmental benefits. Alternatives B and D had the highest overall benefit scores, and Alternative F was disproportionately costly relative to its achieved benefits when compared to the other remedial alternatives. Indeed, the costlier alternatives with larger remedial footprints had lower overall EIBA benefit scores-because of substantially more air emissions, noise, and light impacts, and more disturbance to business, recreational access, and habitat during construction-compared to the less costly and smaller alternatives. Put another way, the adverse effects during construction tended to outweigh the long-term benefits, and the net environmental impacts of the larger remedial alternatives far outweighed their small incremental improvements in risk reduction. Results of this Comprehensive Environmental Response Compensation and Liability Act (CERCLA)-linked environmental analysis were integrated with indicators of economic and social impacts of remediation in a stakeholder values-based sustainability framework. These tools (EIBA, EIBA-based cost-benefit analysis, economic impact assessment, and the stakeholder values-based integration) provide transparent and quantitative evaluations of the benefits and impacts associated with remedial alternatives

Perbandingan Sifat Fisik Beton Yang Menggunakan Semen Portland Pozzolan Dan Semen Portland Tipe I

OpenAIRE

Yusnita, Heni

2011-01-01

The research about concrete by using the Portland pozzolan cement and Portland cement type I has been done with the variation of submersion time is 7, 14, 21, and 28 days. The test is done for physics of the concrete. The sample is made from the ingredients 1 cement : 2 sand : 3 pebble. The result of the researching shows that the used of the Portland pozzolan cement can raise the impact of the concrete as much as 9,15% from concrete which uses the Portland cement type I. Orther side for the ...

Geomorphic floodplain with organic matter (biomass) estimates for Fanno Creek, Oregon

Science.gov (United States)

Sobieszczyk, Steven

2011-01-01

Fanno Creek is a tributary to the Tualatin River and flows though parts of the southwest Portland metropolitan area. The stream is heavily influenced by urban runoff and shows characteristic flashy streamflow and poor water quality commonly associated with urban streams. This data set represents the geomorphic floodplain as derived from light detection and ranging (LiDAR) data and aerial photographic imagery. The floodplain represents current conditions including both anthropogenic alterations and natural historic floodplain features. The floodplain dataset is divided into 13 reach segments and attributed with corresponding organic material load estimates for each reach.

A tunnel runs through it: an inside view of the Tualatin Mountains, Oregon

Science.gov (United States)

Walsh, Ken; Peterson, Gary L.; Beeson, Marvin H.; Wells, Ray E.; Fleck, Robert J.; Evarts, Russell C.; Duvall, Alison; Blakely, Richard J.; Burns, Scott

2011-01-01

The Tualatin Mountains form a northwest-striking ridge about 350 m high that separates Portland, Oregon, from the cities of the Tualatin Valley to the west. Known informally as the Portland Hills, the ridge is a late Cenozoic anticline, bounded by reverse faults that dip toward the anticlinal axis. The anticline is a broad, open fold consisting chiefly of Miocene Columbia River Basalt Group, with remnants of Miocene-Pliocene Troutdale Formation and Pleistocene basalt of the Boring Volcanic Field on the flanks of the anticline. Anticlinal structures similar to the Tualatin Mountains are characteristic of the northern Willamette Valley, where the structures accommodate margin-parallel shortening of the Cascadia fore arc. Global Positioning System (GPS) results indicate that the shortening is due to the northward motion of Oregon at several millimeters per year with respect to stable North America. Some of the uplifts may contain active faults, but the structures are poorly exposed and are overlain by thick Pleistocene loess and Missoula flood deposits. Between 1993 and 1998, construction of the 3-mile-long (4500-m-long) TriMet MAX Light Rail tunnel through the Tualatin Mountains provided an unusual opportunity to investigate the geological structure and history of the Tualatin Mountains. This report is a collaborative effort among the tunnel geologists and the U.S. Geological Survey (USGS) to document the geologic story and quantify late Cenozoic and Quaternary deformation rates of the Tualatin Mountains.

Physicochemical and mechanical properties of zirconium oxide and niobium oxide modified Portland cement-based experimental endodontic sealers.

Science.gov (United States)

Viapiana, R; Flumignan, D L; Guerreiro-Tanomaru, J M; Camilleri, J; Tanomaru-Filho, M

2014-05-01

To evaluate the physicochemical and mechanical properties of Portland cement-based experimental sealers (ES) with different radiopacifying agents (zirconium oxide and niobium oxide micro- and nanoparticles) in comparison with the following conventional sealers: AH Plus, MTA Fillapex and Sealapex. The materials were tested for setting time, compressive strength, flow, film thickness, radiopacity, solubility, dimensional stability and formaldehyde release. Data were subjected to anova and Tukey tests (P 0.05) and lower solubility when compared with MTA Fillapex and Sealapex (P Portland cement-based experimental endodontic sealers presented physicochemical properties according to the specifications no 57 ANSI/ADA (ADA Professional Product Review, 2008) and ISO 6876 (Dentistry - Root Canal Sealing Materials, 2012, British Standards Institution, London, UK). The sealers had setting times and flow ability that was adequate for clinical use, satisfactory compressive strength and low solubility. Additional studies should be carried out with the purpose of decreasing the film thickness and to determine the ideal ratio of radiopacifying agents in Portland cement-based root canal sealers. © 2013 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Understanding mineral trioxide aggregate/Portland-cement: a review of literature and background factors.

Science.gov (United States)

Steffen, R; van Waes, H

2009-06-01

This was to carry out a review of the literature concerning mineral trioxide aggregate (MTA) and Portland cement with regards to clinical, biological and mechanical findings and a possible substitution of MTA through Portland cement for endodontic use. Electronic literature search of scientific papers from January 1993 to January 2009 was carried out on the MEDLINE and Scopus databases using specific key words. In total, 57 papers were identified that dealt with MTA and Portland cement in a relevant way. The review of 50 papers conforming to the applied criteria showed that MTA and Portland cements have the same clinical, biological and mechanical properties. In animal experiments and technical characterisations both materials seemed to have very similar properties. The only difference is bismuth oxide in MTA added for better radio opacity. It seems likely that MTA materials are based on industrial Portland cements mixed with bismuth oxide. More studies, especially some long-term studies comparing MTA and Portland cement, are necessary. The existing literature gives a solid base for clinical studies with Portland cement in order to replace MTA as an endodontic material. Portland cement could be a substitute for most endodontic materials used in primary teeth.

Portland's experience with land use tools to promote green roofs

International Nuclear Information System (INIS)

Johnson, M.

2004-01-01

In the late 1990s, the City of Portland, Oregon faced environmental challenges that prompted the City to mandate environmentally sensitive development. Several programs were developed in response to these challenges, some of which resulted in the creation of land use policies and incentives that promote green roofs. Zoning code provisions were adopted in 2001 to promote eco-roofs in an effort to reduce stormwater runoff, mitigate urban heat island effects, provide habitat for birds, and improve air quality and energy efficiency. The Central City Fundamental Design Guidelines were also revised to encourage eco-roof development. In 2002, the South Waterfront Plan was created to integrate ecological design into an urban environment through sustainability principles and practices. Land use tools were developed to introduce developers to an approach that reduced energy costs and stormwater costs, while also contributing to a project's marketability. These tools were created with the support of programs and policies such as the CSO (Combined Sewer Overflow) Program; eco-roof research which began in 1995 to determine the stormwater management potential of eco-Green roofs; technical assistance to encourage and highlight sustainable development practices; the Stormwater Management Manual that set standards for the amount and quality of stormwater runoff leaving development sites; the G/Rated Program that offers resources for green building practices; the Green Investment Fund that supports the G/Rated Program; and, the Portland Development Commission Green Building Policy financing tool for earth-friendly designs and materials. 34 refs., 2 figs

Preparation and Physical Assessment of Portland Cement Base Composites Containing Nano Particles

OpenAIRE

Amir Mahmoudi

2015-01-01

In this research the effects of adding silica and alumina nanoparticles on flow ability and compressive strength of cementitious composites based on Portland cement were investigated. In the first stage, the rheological behavior of different samples containing nanosilica, nanoalumina and polypropylene, polyvinyl alcohol and polyethylene fibers were evaluated. With increasing of nanoparticles in fresh samples, the slump flow diameter reduced. Fibers reduced the flow abilit...

Characteristics and lessons learned from practice-based research networks (PBRNs in the United States

Directory of Open Access Journals (Sweden)

Keller S

2012-09-01

Full Text Available Melinda M Davis,1,2 Sara Keller,1 Jennifer E DeVoe,1,3 Deborah J Cohen11Department of Family Medicine, 2Oregon Rural Practice-based Research Network, Oregon Health & Science University, Portland, OR, USA; 3OCHIN Practice-based Research Network, Portland, OR, USAAbstract: Practice-based research networks (PBRNs are organizations that involve practicing clinicians in asking and answering clinically relevant research questions. This review explores the origins, characteristics, funding, and lessons learned through practice-based research in the United States. Primary care PBRNs emerged in the USA in the 1970s. Early studies explored the etiology of common problems encountered in primary care practices (eg, headache, miscarriage, demonstrating the gap between research conducted in controlled specialty settings and real-world practices. Over time, national initiatives and an evolving funding climate have shaped PBRN development, contributing to larger networks, a push for shared electronic health records, and the use of a broad range of research methodologies (eg, observational studies, pragmatic randomized controlled trials, continuous quality improvement, participatory methods. Today, there are over 160 active networks registered with the Agency for Healthcare Research and Quality's PBRN Resource Center that engage primary care clinicians, pharmacists, dentists, and other health care professionals in research and quality-improvement initiatives. PBRNs provide an important laboratory for encouraging collaborative research partnerships between academicians and practices or communities to improve population health, conduct comparative effectiveness and patient-centered outcomes research, and study health policy reform. PBRNs continue to face critical challenges that include: (1 adapting to a changing landscape; (2 recruiting and retaining membership; (3 securing infrastructure support; (4 straddling two worlds (academia and community and managing

Portland cement concrete air content study.

Science.gov (United States)

1987-04-20

This study took the analysis of Portland cement concrete air content. Based on the information gathered, this study hold the results were : 1) air-entrained concrete was more durable than non-air entrained concrete all other factors being equal; 2) A...

Nanotechnology-Based Performance Improvements For Portland Cement Concrete - Phase I

Science.gov (United States)

2012-08-16

A fundamental understanding of the nano-structure of Portland cement concrete (PCC) is the key to realizing significant breakthroughs regarding high performance and susta : (MBTC 2095/3004) using molecular dynamics (MD) provided new understanding of ...

Predicting fecal indicator organism contamination in Oregon coastal streams

International Nuclear Information System (INIS)

Pettus, Paul; Foster, Eugene; Pan, Yangdong

2015-01-01

In this study, we used publicly available GIS layers and statistical tree-based modeling (CART and Random Forest) to predict pathogen indicator counts at a regional scale using 88 spatially explicit landscape predictors and 6657 samples from non-estuarine streams in the Oregon Coast Range. A total of 532 frequently sampled sites were parsed down to 93 pathogen sampling sites to control for spatial and temporal biases. This model's 56.5% explanation of variance, was comparable to other regional models, while still including a large number of variables. Analysis showed the most important predictors on bacteria counts to be: forest and natural riparian zones, cattle related activities, and urban land uses. This research confirmed linkages to anthropogenic activities, with the research prediction mapping showing increased bacteria counts in agricultural and urban land use areas and lower counts with more natural riparian conditions. - Highlights: • We modeled fecal indicator pathogens in Oregon Coast range streams. • We used machine learning tools with only publicly available data. • These models demonstrate the importance of riparian land use on water quality. • Regional water quality was characterized in streams with little to no monitoring. - A desktop approach to predict stream pathogens from exclusively publicly available data sets on a regional scale.

Gravity Data for the Greater Portland Area

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The gravity station data (1,522 records) were compiled by the Portland State University. This data base was received in August 1990. Principal gravity parameters...

78 FR 73539 - Notice to All Interested Parties of the Termination of the Receivership of 7166, The BENJ...

Science.gov (United States)

2013-12-06

... Receivership of 7166, The BENJ Franklin Federal Savings and Loan Association Portland, Oregon Notice is hereby... Federal Savings and Loan Association, Portland, Oregon (``the Receiver'') intends to terminate its receivership for said institution. The FDIC was appointed receiver of The BENJ Franklin Federal Savings and...

Dense chlorinated solvents and other DNAPLs in groundwater

DEFF Research Database (Denmark)

Broholm, K.

1996-01-01

Anmeldelse af Pankow,J.F. & Cherry,J.A.: Dense chlorinated solvents and other DNAPLs in groundwater. Waterloo Press, Portland, Oregon, USA, 1996......Anmeldelse af Pankow,J.F. & Cherry,J.A.: Dense chlorinated solvents and other DNAPLs in groundwater. Waterloo Press, Portland, Oregon, USA, 1996...

Results of hydrologic monitoring of a landslide-prone hillslope in Portland’s West Hills, Oregon, 2006–2017

Science.gov (United States)

Smith, Joel B.; Godt, Jonathan W.; Baum, Rex L.; Coe, Jeffrey A.; Ellis, William L.; Jones, Eric S.; Burns, Scott F.

2017-09-15

The West Hills of Portland, in the southern Tualatin Mountains, trend northwest along the west side of Portland, Oregon. These silt-mantled mountains receive significant wet-season precipitation and are prone to sliding during wet conditions, occasionally resulting in property damage or casualties. In an effort to develop a baseline for interpretive analysis of the groundwater response to rainfall, an automated monitoring system was installed in 2006 to measure rainfall, pore-water pressure, soil suction, soil-water potential, and volumetric water content at 15-minute intervals. The data show a cyclical pattern of groundwater and moisture content levels—wet from October to May and dry between June and September. Saturated soil conditions tend to last throughout the wet season. These data show the hydrologic response of the monitored area to rainfall and provide insight into the dynamics of rainfall-initiated landsliding. This report details the monitoring methods and presents data collected from January 10, 2006, through January 23, 2017.

Neighborhood change and the role of environmental stewardship: a case study of green infrastructure for stormwater in the City of Portland, Oregon, USA

Directory of Open Access Journals (Sweden)

Vivek Shandas

2015-09-01

Full Text Available Throughout the history of cities, the ecological landscape has often been buried, removed, or taken for granted. A recent recognition that humans are part of the global ecosystem, and that human actions both cause and are affected by ecological change, brings with it an awareness of the value of nature in cities and of natural systems on which cities depend. The feedbacks between humans and their environment within an urban context can have profound implications for the growth of and change in cities, yet there is a limited understanding of the interactions between biophysical changes in cities and the implications of these changes on the quality of life for residents. The application of a coupled human and natural systems (CHANS framework provides a timely and fruitful opportunity to enrich the theory, methods, and understanding of these feedbacks and interconnections. Here, I integrated biophysical and social dimensions relevant to managing urban stormwater by examining a case study of Portland, Oregon, USA. I used empirical data from a pre-post survey (2-yr span of residents in eight urban neighborhoods to describe feedbacks and interactions between a localized biophysical change in the form of a large-scale decentralized stormwater program and the resulting changes in resident's perceptions in neighborhoods undergoing rapid change. My findings corroborate earlier findings suggesting that people with higher income and education levels are more likely to participate in stewardship actions. The results also suggest an overall and initial negative perception of neighborhoods facilities and services immediately following the construction of decentralized stormwater facilities, but conversely, high levels of anticipation for their construction. By describing these findings through a CHANS framework, I make explicit the importance of integrating scientific understanding, governance efforts, and human behaviors to address acute urban environmental

Basalt waste added to Portland cement

Directory of Open Access Journals (Sweden)

Thiago Melanda Mendes

2016-08-01

Full Text Available Portland cement is widely used as a building material and more than 4.3 billion tons were produced in 2014, with increasing environmental impacts by this industry, mainly through CO2 emissions and consumption of non-removable raw materials. Several by-products have been used as raw materials or fuels to reduce environmental impacts. Basaltic waste collected by filters was employed as a mineral mixture to Portland cement and two fractions were tested. The compression strength of mortars was measured after 7 days and Scanning Electron Microscopy (SEM and Electron Diffraction Scattering (EDS were carried out on Portland cement paste with the basaltic residue. Gains in compression strength were observed for mixtures containing 2.5 wt.% of basaltic residue. Hydration products observed on surface of basaltic particles show the nucleation effect of mineral mixtures. Clinker substitution by mineral mixtures reduces CO2 emission per ton of Portland cement.

Chemical constitution, physical properties, and biocompatibility of experimentally manufactured Portland cement.

Science.gov (United States)

Hwang, Yun-Chan; Kim, Do-Hee; Hwang, In-Nam; Song, Sun-Ju; Park, Yeong-Joon; Koh, Jeong-Tae; Son, Ho-Hyun; Oh, Won-Mann

2011-01-01

An experimental Portland cement was manufactured with pure raw materials under controlled laboratory conditions. The aim of this study was to compare the chemical constitution, physical properties, and biocompatibility of experimentally manufactured Portland cement with those of mineral trioxide aggregate (MTA) and Portland cement. The composition of the cements was determined by scanning electron microscopy (SEM) and energy-dispersive x-ray analysis (EDAX). The setting time and compressive strength were tested. The biocompatibility was evaluated by using SEM and XTT assay. SEM and EDAX revealed the experimental Portland cement to have a similar composition to Portland cement. The setting time of the experimental Portland cement was significantly shorter than that of MTA and Portland cement. The compressive strength of the experimental Portland cement was lower than that of MTA and Portland cement. The experimental Portland cement showed a similar biocompatibility to MTA. The experimental Portland cement might be considered as a possible substitute for MTA in clinical usage after further testing. Copyright © 2011 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Flow properties of MK-based geopolymer pastes. A comparative study with standard Portland cement pastes.

Science.gov (United States)

Favier, Aurélie; Hot, Julie; Habert, Guillaume; Roussel, Nicolas; d'Espinose de Lacaillerie, Jean-Baptiste

2014-02-28

Geopolymers are presented in many studies as alternatives to ordinary Portland cement. Previous studies have focused on their chemical and mechanical properties, their microstructures and their potential applications, but very few have focussed on their rheological behaviour. Our work highlights the fundamental differences in the flow properties, which exist between geopolymers made from metakaolin and Ordinary Portland Cement (OPC). We show that colloidal interactions between metakaolin particles are negligible and that hydrodynamic effects control the rheological behaviour. Metakaolin-based geopolymers can then be described as Newtonian fluids with the viscosity controlled mainly by the high viscosity of the suspending alkaline silicate solution and not by the contribution of direct contacts between metakaolin grains. This fundamental difference between geopolymers and OPC implies that developments made in cement technology to improve rheological behaviour such as plasticizers will not be efficient for geopolymers and that new research directions need to be explored.

New geologic mapping of the northwestern Willamette Valley, Oregon, and its American Viticultural Areas (AVAs)—A foundation for understanding their terroir

Science.gov (United States)

Wells, Ray E.; Haugerud, Ralph A.; Niem, Alan; Niem, Wendy; Ma, Lina; Madin, Ian; Evarts, Russell C.

2018-04-10

A geologic map of the greater Portland, Oregon, metropolitan area is planned that will document the region’s complex geology (currently in review: “Geologic map of the greater Portland metropolitan area and surrounding region, Oregon and Washington,” by Wells, R.E., Haugerud, R.A., Niem, A., Niem, W., Ma, L., Evarts, R., Madin, I., and others). The map, which is planned to be published as a U.S. Geological Survey Scientific Investigations Map, will consist of 51 7.5′ quadrangles covering more than 2,500 square miles, and it will represent more than 100 person-years of geologic mapping and studies. The region was mapped at the relatively detailed scale of 1:24,000 to improve understanding of its geology and its earthquake hazards. More than 100 geologic map units will record the 50-million-year history of volcanism, sedimentation, folding, and faulting above the Cascadia Subduction Zone. The geology contributes to the varied terroir of four American Viticultural Areas (AVAs) in the northwestern Willamette Valley: the Yamhill-Carlton, Dundee Hills, Chehalem Mountains, and Ribbon Ridge AVAs. Terroir is defined as the environmental conditions, especially climate and soils, that influence the quality and character of a region’s crops—in this case, grapes for wine.On this new poster (“New geologic mapping of the northwestern Willamette Valley, Oregon, and its American Viticultural Areas (AVAs)—A foundation for understanding their terroir”), we present the geologic map at a reduced scale (about 1:175,000) to show the general distribution of geologic map units, and we highlight, discuss, and illustrate six major geologic events that helped shape the region and form its terrior. We also discuss the geologic elements that contribute to the character of each of the four AVAs in the northwestern Willamette Valley.

Renewing Oregon's Economy: Growing Jobs and Industries through Innovation. A Report from the Oregon Council for Knowledge and Economic Development.

Science.gov (United States)

2003

The Oregon Council for Knowledge and Economic Development (OCKED), a collaborative effort among Oregon's higher education institutions, economic development department, and the private sector, is charged with developing strategies to enhance Oregon's economic competitiveness in a knowledge-based, global economy. This report describes the council's…

Nuevos conglomerantes complementarios del cemento portland

OpenAIRE

Argiz, Cristina; Menéndez, Esperanza; Moragues, Amparo; Sanjuan-Barbudo, Miguel

2012-01-01

El desarrollo de nuevos conglomerantes complementarios al cemento portland se presenta como una alternativa que permitirá reciclar residuos, entre otros posibles beneficios. Estos nuevos materiales difícilmente podrán competir con el cemento portland ya que sus aplicaciones son limitadas y su coste, en general, más elevado.

Effectiveness of inorganic membrane mixture of natural zeolite and portland white cement in purifying of peat water based on turbidity parameter

Science.gov (United States)

Elfiana; Fuadi, A.; Diana, S.

2018-04-01

Peat water is water surface that brownish red colour caused by the contained constituents. Solving the peat watercolor problem requires special attention considering the quantity of peat water and suitable to be used to meet the daily needs. This study aims to know the inorganic membrane capability of mix nature zeolite and white Portland cement to purifying the peat water based on turbidity parameter. The study was conducted by varying the composition of nature zeolite (Za) and white Portland cement (Sp) in the ratio of Za: Sp is (25%:75%; 50%:50%; 75%:25%) with zeolite condition activated using HCl 2M and nonactivated zeolite treatments. The result of the characteristic test on membrane morphology using SEM (Scanning Electron Microscope) showed that the pore surface size of the membrane is 2 μm that could classified in microfiltration membrane an organic type. The characteristic test showed also resulted in the density of 0.77 to 0.86 gr/cm3, porosity 26.22% to 35.93%, and permeability 2736.19 to 8428.15. While the water retention capacity is in range of 30.64% to 46.46%, The result of inorganic membrane application on peat water showed turbidity of peat water decreased 94.17%, from 10.3 NTU to 0.6 NTU.

Petrographic Analysis of Portland Cement Concrete Cores from Pease Air National Guard Base, New Hampshire

Science.gov (United States)

2016-11-01

Petrographic Analysis of Portland Cement Concrete Cores from Pease Air National Guard Base, New Hampshire E n g in e e r R e s e a rc h a n d...id, age of the concrete being evaluated and tests performed...4 3 Preface This study was conducted in support of the Air Force Civil Engineer Center (AFCEC) to assess concrete obtained from Pease

Poet Portland Approval

Science.gov (United States)

This update August 9, 2016 letter from EPA approves the petition, with modifications, from Poet Biorefining-Portland, LLC, regarding non-grandfathered ethanol produced through a dry mill process, qualifying under the Clean Air Act for renewable fuel

Annotated bibliography of the geology of the Columbia Plateau (Columbia River Basalt) and adjacent areas of Oregon

International Nuclear Information System (INIS)

Bela, J.

1979-01-01

This bibliography containing approximately 2000 entries was prepared by the Oregon Department of Geology and Mineral Industries under Subcontract SA-913 with Rockwell Hanford Operations' Basalt Waste Isolation Program. The objective of the Basalt Waste Isolation Program is to determine the feasibility of storing nuclear waste within the Columbia River Basalt Group. Under the geologic portion of this program, the stratigraphic, structural, tectonic, seismic, and hydrologic aspects of the Columbia Plateau are being examined. Other aspects of the Basalt Waste Isolation Program are concerned with systems integration, engineered barriers, engineering testing, and construction of a near-surface test facility. The area covered in this bibliography comprises that area north of 43 0 30' latitude and east of the Willamette Meridian, which is located just west of Portland. The bibliographic entries are presented in two forms. The first is an alphabetized listing of all articles dealing with the geology of the Columbia Plateau (Columbia River Basalt) and adjacent areas of Oregon. The second form consists of an alphabetized listing of the entries subdivided under fourteen categories

Annotated bibliography of the geology of the Columbia Plateau (Columbia River Basalt) and adjacent areas of Oregon

Energy Technology Data Exchange (ETDEWEB)

Bela, J.

1979-01-01

This bibliography containing approximately 2000 entries was prepared by the Oregon Department of Geology and Mineral Industries under Subcontract SA-913 with Rockwell Hanford Operations' Basalt Waste Isolation Program. The objective of the Basalt Waste Isolation Program is to determine the feasibility of storing nuclear waste within the Columbia River Basalt Group. Under the geologic portion of this program, the stratigraphic, structural, tectonic, seismic, and hydrologic aspects of the Columbia Plateau are being examined. Other aspects of the Basalt Waste Isolation Program are concerned with systems integration, engineered barriers, engineering testing, and construction of a near-surface test facility. The area covered in this bibliography comprises that area north of 43/sup 0/30' latitude and east of the Willamette Meridian, which is located just west of Portland. The bibliographic entries are presented in two forms. The first is an alphabetized listing of all articles dealing with the geology of the Columbia Plateau (Columbia River Basalt) and adjacent areas of Oregon. The second form consists of an alphabetized listing of the entries subdivided under fourteen categories. (RWR)

Organic Compounds in Clackamas River Water Used for Public Supply near Portland, Oregon, 2003-05

Science.gov (United States)

Carpenter, Kurt D.; McGhee, Gordon

2009-01-01

Organic compounds studied in this U.S. Geological Survey (USGS) assessment generally are man-made, including pesticides, gasoline hydrocarbons, solvents, personal care and domestic-use products, disinfection by-products, and manufacturing additives. In all, 56 compounds were detected in samples collected approximately monthly during 2003-05 at the intake for the Clackamas River Water plant, one of four community water systems on the lower Clackamas River. The diversity of compounds detected suggests a variety of different sources and uses (including wastewater discharges, industrial, agricultural, domestic, and others) and different pathways to drinking-water supplies (point sources, precipitation, overland runoff, ground-water discharge, and formation during water treatment). A total of 20 organic compounds were commonly detected (in at least 20 percent of the samples) in source water and (or) finished water. Fifteen compounds were commonly detected in source water, and five of these compounds (benzene, m- and p-xylene, diuron, simazine, and chloroform) also were commonly detected in finished water. With the exception of gasoline hydrocarbons, disinfection by-products, chloromethane, and the herbicide diuron, concentrations in source and finished water were less than 0.1 microgram per liter and always less than human-health benchmarks, which are available for about 60 percent of the compounds detected. On the basis of this screening-level assessment, adverse effects to human health are assumed to be negligible (subject to limitations of available human-health benchmarks).

Glycerol Salicylate-based Pulp-Capping Material Containing Portland Cement.

Science.gov (United States)

Portella, Fernando Freitas; Collares, Fabrício Mezzomo; Santos, Paula Dapper; Sartori, Cláudia; Wegner, Everton; Leitune, Vicente Castelo Branco; Samuel, Susana Maria Werner

2015-01-01

The purpose of this study was to evaluate the water sorption, solubility, pH and ability to diffuse into dentin of a glycerol salicylate-based, pulp-capping cement in comparison to a conventional calcium hydroxide-based pulp capping material (Hydcal). An experimental cement was developed containing 60% glycerol salicylate resin, 10% methyl salicylate, 25% calcium hydroxide and 5% Portland cement. Water sorption and solubility were determined based on mass changes in the samples before and after the immersion in distilled water for 7 days. Material discs were stored in distilled water for 24 h, 7 days and 28 days, and a digital pHmeter was used to measure the pH of water. The cement's ability to diffuse into bovine dentin was assessed by Raman spectroscopy. The glycerol salicylate-based cement presented higher water sorption and lower solubility than Hydcal. The pH of water used to store the samples increased for both cements, reaching 12.59 ± 0.06 and 12.54 ± 0.05 after 7 days, for Hydcal and glycerol salicylate-based cements, respectively. Both cements were able to turn alkaline the medium at 24 h and sustain its alkalinity after 28 days. Hydcal exhibited an intense diffusion into dentin up to 40 µm deep, and the glycerol salicylate-based cement penetrated 20 µm. The experimental glycerol salicylate-based cement presents good sorption, solubility, ability to alkalize the surrounding tissues and diffusion into dentin to be used as pulp capping material.

Alkali binding in hydrated Portland cement paste

NARCIS (Netherlands)

Chen, Wei; Brouwers, Jos

2010-01-01

The alkali-binding capacity of C–S–H in hydrated Portland cement pastes is addressed in this study. The amount of bound alkalis in C–S–H is computed based on the alkali partition theories firstly proposed by Taylor (1987) and later further developed by Brouwers and Van Eijk (2003). Experimental data

INFLUENCE OF SUBSTITUTION OF ORDINARY PORTLAND CEMENT BY SILICA FUME ON THE HYDRATION OF SLAG-PORTLAND CEMENT PASTES

Directory of Open Access Journals (Sweden)

E.A. El-Alfi

2011-06-01

Full Text Available Effect of gradual substitution of ordinary Portland cement by a few percent of silica fume (0.0, 2.5, 5.0 and 7.5 wt.% on the hydration properties of slag-Portland cement pastes up to 12 months was investigated. The results show that the composite cement pastes containing silica fume give the higher physico-mechanical properties than that of the slag-Portland cement. Also, the XRD results reveal that the peak of Ca(OH2 shows higher intensity in the sample without silica fume and completely disappears in the sample containing 7.5 wt.% silica fume content. Also, the intensity peaks of C4AH13 sharply increase with silica fume content.

Application of probabilistic risk assessment: Evaluating remedial alternatives at the Portland Harbor Superfund Site, Portland, Oregon, USA.

Science.gov (United States)

Ruffle, Betsy; Henderson, James; Murphy-Hagan, Clare; Kirkwood, Gemma; Wolf, Frederick; Edwards, Deborah A

2018-01-01

A probabilistic risk assessment (PRA) was performed to evaluate the range of potential baseline and postremedy health risks to fish consumers at the Portland Harbor Superfund Site (the "Site"). The analysis focused on risks of consuming fish resident to the Site containing polychlorinated biphenyls (PCBs), given that this exposure scenario and contaminant are the primary basis for US Environmental Protection Agency's (USEPA's) selected remedy per the January 2017 Record of Decision (ROD). The PRA used probability distributions fit to the same data sets used in the deterministic baseline human health risk assessment (BHHRA) as well as recent sediment and fish tissue data to evaluate the range and likelihood of current baseline cancer risks and noncancer hazards for anglers. Areas of elevated PCBs in sediment were identified on the basis of a geospatial evaluation of the surface sediment data, and the ranges of risks and hazards associated with pre- and postremedy conditions were calculated. The analysis showed that less active remediation (targeted to areas with the highest concentrations) compared to the remedial alternative selected by USEPA in the ROD can achieve USEPA's interim risk management benchmarks (cancer risk of 10 -4 and noncancer hazard index [HI] of 10) immediately postremediation for the vast majority of subsistence anglers that consume smallmouth bass (SMB) fillet tissue. In addition, the same targeted remedy achieves USEPA's long-term benchmarks (10 -5 and HI of 1) for the majority of recreational anglers. Additional sediment remediation would result in negligible additional risk reduction due to the influence of background. The PRA approach applied here provides a simple but adaptive framework for analysis of risks and remedial options focused on variability in exposures. It can be updated and refined with new data to evaluate and reduce uncertainty, improve understanding of the Site and target populations, and foster informed remedial decision

Comparison of the physical and mechanical properties of MTA and portland cement.

Science.gov (United States)

Islam, Intekhab; Chng, Hui Kheng; Yap, Adrian U Jin

2006-03-01

This study evaluated and compared the pH, radiopacity, setting time, solubility, dimensional change, and compressive strength of ProRoot MTA (PMTA), ProRoot MTA (tooth colored formula) (WMTA), white Portland cement (WP), and ordinary Portland cement (OP). The results showed that PMTA and Portland cement have very similar physical properties. However, the radiopacity of Portland cement is much lower than that of PMTA. The compressive strength of PMTA was greater than Portland cement at 28 days. The major constituent of PMTA is Portland cement. Given the low cost of Portland cement and similar properties when compared to PMTA, it is reasonable to consider Portland cement as a possible substitute for PMTA in endodontic applications. However, industrially manufactured Portland cement is not approved currently for use in the United States and therefore no clinical recommendation can be made for its use in the human body. Further in vitro and in vivo tests, especially with regards its biocompatibility, should be conducted to ascertain if it meets the FDA requirements for use as a medical device.

Arabidopsis thaliana resistance to insects, mediated by an earthworm-produced organic soil amendment.

Science.gov (United States)

Cardoza, Yasmin J

2011-02-01

Vermicompost is an organic soil amendment produced by earthworm digestion of organic waste. Studies show that plants grown in soil amended with vermicompost grow faster, are more productive and are less susceptible to a number of arthropod pests. In light of these studies, the present study was designed to determine the type of insect resistance (antixenosis or antibiosis) present in plants grown in vermicompost-amended potting soil. Additionally, the potential role of microarthropods, entomopathogenic organisms and non-pathogenic microbial flora found in vermicompost on insect resistance induction was investigated. Findings show that vermicompost from two different sources (Raleigh, North Carolina, and Portland, Oregon) were both effective in causing Arabidopsis plants to be resistant to the generalist herbivore Helicoverpa zea (Boddie). However, while the Raleigh (Ral) vermicompost plant resistance was expressed as both non-preference (antixenosis) and milder (lower weight and slower development) toxic effect (antibiosis) resistance, Oregon (OSC) vermicompost plant resistance was expressed as acute antibiosis, resulting in lower weights and higher mortality rates. Vermicompost causes plants to have non-preference (antixenosis) and toxic (antibiosis) effects on insects. This resistance affects insect development and survival on plants grown in vermicompost-amended soil. Microarthropods and entomopathogens do not appear to have a role in the resistance, but it is likely that resistance is due to interactions between the microbial communities in vermicompost with plant roots, as is evident from vermicompost sterilization assays conducted in this study. Copyright © 2010 Society of Chemical Industry.

Radiopacity of portland cement associated with different radiopacifying agents.

Science.gov (United States)

Húngaro Duarte, Marco Antonio; de Oliveira El Kadre, Guâniara D'arc; Vivan, Rodrigo Ricci; Guerreiro Tanomaru, Juliane Maria; Tanomaru Filho, Mário; de Moraes, Ivaldo Gomes

2009-05-01

This study evaluated the radiopacity of Portland cement associated with the following radiopacifying agents: bismuth oxide, zinc oxide, lead oxide, bismuth subnitrate, bismuth carbonate, barium sulfate, iodoform, calcium tungstate, and zirconium oxide. A ratio of 20% radiopacifier and 80% white Portland cement by weight was used for analysis. Pure Portland cement and dentin served as controls. Cement/radiopacifier and dentin disc-shaped specimens were fabricated, and radiopacity testing was performed according to the ISO 6876/2001 standard for dental root sealing materials. Using Insight occlusal films, the specimens were radiographed near to a graduated aluminum stepwedge varying from 2 to 16 mm in thickness. The radiographs were digitized and radiopacity compared with the aluminum stepwedge using Digora software (Orion Corporation Soredex, Helsinki, Finland). The radiographic density data were converted into mmAl and analyzed statistically by analysis of variance and Tukey-Kramer test (alpha = 0.05). The radiopacity of pure Portland cement was significantly lower (p cement/radiopacifier mixtures were significantly more radiopaque than dentin and Portland cement alone (p cement/bismuth oxide and Portland cement/lead oxide presented the highest radiopacity values and differed significantly from the other materials (p cement/zinc oxide presented the lowest radiopacity values of all mixtures (p cement as radiopacifying agents. However, the possible interference of the radiopacifiers with the setting chemistry, biocompatibility, and physical properties of the Portland cement should be further investigated before any clinical recommendation can be done.

Microstructure and durability of Portland cement-carbon nanotube composites

OpenAIRE

MacLeod, Alastair James Neil

2017-01-01

The incorporation of carbon nanotubes (CNTs), fibres with diameters less than 100 nanometres that exhibit a tensile strength in excess of ten times greater than steel, into Portland cement (OPC) is a relatively novel, yet promising, development for next-generation construction materials exhibiting enhanced strength and ductility, even multifunctionality. When added to Portland cement, creating a Portland cement-CNT nanocomposite material (OPC-CNT), CNTs promote the nucleation of the princi...

Hospital waste ashes in Portland cement mortars

International Nuclear Information System (INIS)

Genazzini, C.; Zerbino, R.; Ronco, A.; Batic, O.; Giaccio, G.

2003-01-01

Nowadays, most concretes incorporate mineral additions such as pozzolans, fly ash, silica fume, blast furnace slag, and calcareous filler among others. Although the technological and economical benefits were the main reasons for the use of mineral additions, the prevention of environmental contamination by means of proper waste disposal becomes a priority. The chance of incorporating hospital waste ashes in Portland cement-based materials is presented here. Ash characterization was performed by chemical analysis, X-ray diffraction, radioactive material detection, and fineness and density tests. Conduction calorimetry and setting time tests were developed on pastes including ash contents from 0% to 100%. Mortars were prepared including ash contents up to 50% of cement. The results of setting time, temperature development, flexural and compressive strengths, water absorption, density, and leachability are analyzed. Results indicate that Portland cement systems could become an alternative for the disposal of this type of ashes

Portland General Electric Company report on the operating and startup experience with control and instrumentation and electrical systems at the Trojan Nuclear Plant

International Nuclear Information System (INIS)

Zimmerman, G.A.

1977-01-01

The Trojan Nuclear Plant is an 1178 MWe nuclear plant located on the Columbia River 40 miles northwest of Portland, Oregon. The Nuclear Stream Supply System vendor is Westinghouse with a General Electric turbine generator. The reactor is rated and licensed for 3423 MWt (1178 MWe) and the turbine generator is designed for 3570 MWt(1219 MWe). The startup phase testing of Trojan commenced on November 21, 1975, upon receipt of our NRC Operating License. The startup testing program was completed on May 22, 1976, following 100 hours of full-power operation, at which time a scheduled summer maintenance outage began. Some of the highlights and milestones of the startup testing program are described

Interfacial morphology and domain configurations in 0-3 PZT-Portland cement composites

International Nuclear Information System (INIS)

Jaitanong, N.; Zeng, H.R.; Li, G.R.; Yin, Q.R.; Vittayakorn, W.C.; Yimnirun, R.; Chaipanich, A.

2010-01-01

Cement-based piezoelectric composites have attracted great attention recently due to their promising applications as sensors in smart structures. Lead zirconate titanate (PZT) and Portland cement (PC) composite were fabricated using 60% of PZT by volume. Scanning Electron Microscope and piezoresponse force microscope were used to investigate the morphology and domain configurations at the interfacial zone of PZT-Portland cement composites. Angular PZT ceramic grains were found to bind well with the cement matrix. The submicro-scale domains were clearly observed by piezoresponse force microscope at the interfacial regions between the piezoelectric PZT phase and Portland cement phase, and are clearer than the images obtained for pure PZT. This is thought to be due to the applied internal stress of cement to the PZT ceramic particle which resulted to clearer images.

Coyote Springs Cogeneration Project, Morrow County, Oregon: Draft Environmental Impact Statement.

Energy Technology Data Exchange (ETDEWEB)

United States. Bonneville Power Administration.

1994-01-01

BPA is considering whether to transfer (wheel) electrical power from a proposed privately-owned, combustion-turbine electrical generation plant in Oregon. The plant would be fired by natural gas and would use combined-cycle technology to generate up to 440 average megawatts (aMW) of energy. The plant would be developed, owned, and operated by Portland General Electric Company (PGE). The project would be built in eastern Oregon, just east of the City of Boardman in Morrow County. The proposed plant would be built on a site within the Port of Morrow Industrial Park. The proposed use for the site is consistent with the County land use plan. Building the transmission line needed to interconnect the power plant to BPA`s transmission system would require a variance from Morrow County. BPA would transfer power from the plant to its McNary-Slatt 500-kV transmission line. PGE would pay BPA for wheeling services. Key environmental concerns identified in the scoping process and evaluated in the draft Environmental Impact Statement (DEIS) include these potential impacts: (1) air quality impacts, such as emissions and their contributions to the {open_quotes}greenhouse{close_quotes} effect; (2) health and safety impacts, such as effects of electric and magnetic fields, (3) noise impacts, (4) farmland impacts, (5) water vapor impacts to transportation, (6) economic development and employment impacts, (7) visual impacts, (8) consistency with local comprehensive plans, and (9) water quality and supply impacts, such as the amount of wastewater discharged, and the source and amount of water required to operate the plant. These and other issues are discussed in the DEIS. The proposed project includes features designed to reduce environmental impacts. Based on studies completed for the DEIS, adverse environmental impacts associated with the proposed project were identified, and no evidence emerged to suggest that the proposed action is controversial.

78 FR 25755 - Announcement of Funding Awards; Energy Innovation Fund-Multifamily Pilot Program Fiscal Year 2010

Science.gov (United States)

2013-05-02

... Community Place, 7441. Cecil, Frederick, Crownsville, MD 21032. Hartford, Howard, Montgomery, Prince George... Greater Portland, OR 1020 SW Taylor, Suite 585, Portland, 5680. metropolitan area. Oregon 97205. NRG...

Oregon's medicaid transformation -- observations on organizational structure and strategy.

Science.gov (United States)

Chang, Anna Marie; Cohen, Deborah J; McCarty, Dennis; Rieckmann, Traci; McConnell, K John

2015-02-01

In the Point article, Steven W. Howard et al. argue that the Oregon Health Authority's coordinated care organizations (CCOs) are different from traditional Medicaid managed care organizations in ways designed to improve care coordination and transparency, incorporate greater collaborative governance and community accountability, and reform payment and delivery of care. Although the Point article notes specific challenges to implementing reforms, this Counterpoint article identifies the progress and successes of Oregon's CCOs in each of the aforementioned areas on the basis of empirical research, which suggests that CCOs appear to be viable innovations. Copyright © 2015 by Duke University Press.

76 FR 28315 - Security Zone; Portland Rose Festival on Willamette River

Science.gov (United States)

2011-05-17

... Zone; Portland Rose Festival on Willamette River AGENCY: Coast Guard, DHS. ACTION: Notice of enforcement of regulation. SUMMARY: The Coast Guard will enforce the Portland Rose Festival Security Zone in... River during the Portland Rose festival. During the enforcement period, no person or vessel may enter or...

Potencialidades da metacaolinita e do tijolo queimado moído como substitutos parciais do cimento Portland Potentialities of metakaolin and crushed waste calcined clay brick as partial replacement of Portland cement

Directory of Open Access Journals (Sweden)

João de Farias Filho

2000-12-01

Full Text Available Avalia-se, neste trabalho, a potencialidade do uso da metacaolinita e dos resíduos de produção de tijolos cerâmicos queimados finamente moídos, como substitutos parciais do cimento Portland. Os materiais foram caracterizados física, química e mineralogicamente, além de determinado o índice de atividade pozolânica com cimento Portland. A evolução da resistência a compressão e a flexão das argamassas foi avaliada até as idades de, respectivamente, 365 e 208 dias. As porcentagens de substituição do cimento Portland, em peso, pelos materiais pozolânicos, variaram de 20 a 50%, enquanto o fator água/cimento variou de 0,37 a 0,45. Os resultados obtidos indicaram que a metacaolinita e o tijolo moído queimado possuem elevada atividade pozolânica e que a resistência a compressão, aos 28 dias, das argamassas mistas, foi superior à das argamassas de cimento Portland para os níveis de substituição e fatores água/cimento estudados. Um modelo matemático para predição da resistência à compressão das argamassas mistas é proposto com base em um desenho fatorial de experimentos.This paper evaluates the potentiality of metakaolin and crushed waste fired clay brick as cement replacement materials. They were characterised physically, chemically and mineralogically and their activity with Portland cement determined. The influence of the partial replacement of Portland cement on the development of compressive and flexural strength was evaluated until the age of, respectively, 365 and 208 days. The percentage of cement replacement, in weight, ranged from 20 to 50%, whereas the water/cement ratio ranged from 0.37 to 0.45. The results obtained show that the metakaolin and crushed calcined clay brick presented a good pozolanic activity and that the compressive strength of the blended mortars after 28 days of cure was higher than that observed for the reference Portland cement for all levels of cement replacement and water/cement ratio. A

Applications of solid-state Nuclear Magnetic Resonance (NMR) in studies of Portland cements-based materials

DEFF Research Database (Denmark)

Skibsted, Jørgen; Andersen, Morten Daugaard; Jakobsen, Hans Jørgen

2007-01-01

Solid-state NMR spectroscopy represents an important research tool in the characterization of a range of structural properties for cement-based materials. Different approaches of the technique can be used to obtain information on hydration kinetics, mobile and bound water, porosity, and local...... atomic structures. After a short introduction to these NMR techniques, it is exemplified how magic-angle spinning (MAS) NMR can provide quantitative and structural information about specific phases in anhydrous and hydrated Portland cements with main emphasis on the incorporation of Al3+ ions...

Preterm delivery among people living around Portland cement plants

International Nuclear Information System (INIS)

Yang, C.-Y.; Chang, C.-C.; Tsai, S.-S.; Huang, H.-Y.; Ho, C.-K.; Wu, T.-N.; Sung, F.-C.

2003-01-01

The Portland cement industry is the main source of particulate air pollution in Kaohsiung city. Data in this study concern outdoor air pollution and the health of individuals living in communities in close proximity to Portland cement plants. The prevalence of delivery of preterm birth infants as significantly higher in mothers living within 0-2 km of a Portland cement plant than in mothers living within 2-4 km. After controlling for several possible confounders (including maternal age, season, marital status, maternal education, and infant sex), the adjusted odds ratio was 1.30 (95% I=1.09-1.54) for the delivery of preterm infants for mothers living close to he Portland cement plants, chosen at the start to be from 0 to 2 km. These data provide further support for the hypothesis that air pollution can affect he outcome of pregnancy

A consumption-based GHG inventory for the U.S. state of Oregon.

Science.gov (United States)

Erickson, Peter; Allaway, David; Lazarus, Michael; Stanton, Elizabeth A

2012-04-03

Many U.S. states conduct greenhouse gas (GHG) inventories to inform their climate change planning efforts. These inventories usually follow a production-based method adapted from the Intergovernmental Panel on Climate Change. States could also take a consumption-based perspective, however, and estimate all emissions released to support consumption in their state, regardless of where the emissions occur. In what may be the first such comprehensive inventory conducted for a U.S. state, we find that consumption-based emissions for Oregon are 47% higher than those released in-state. This finding implies that Oregon's contribution to global greenhouse gas emissions (carbon footprint) is considerably higher than traditional production-based methods would suggest. Furthermore, the consumption-based inventory helps highlight the role of goods and services (and associated purchasing behaviors) more so than do production-based methods. Accordingly, a consumption-based perspective opens new opportunities for many states and their local government partners to reduce GHG emissions, such as initiatives to advance lower-carbon public sector or household consumption, that are well within their sphere of influence. State and local governments should consider conducting consumption-based GHG inventories and adopting consumption-based emission reductions targets in order to broaden the reach and effectiveness of state and local actions in reducing global GHG emissions. Consumption-based frameworks should be viewed as a complement to, but not a substitute for, production-based (in-state) GHG emissions inventories and targets.

PLA 2010 Conference: Plenty for the Price

Science.gov (United States)

Miller, Rebecca

2010-01-01

This article outlines Public Library Association (PLA) 2010 annual conference to be held in Oregon Convention Center, Portland on March 23-27. The days quickly fill up with the picks of over 100 programs as well as valuable "talk tables" and special events. The well-organized schedule, divided into eight broad tracks (e.g., technology,…

Synthesis of pure Portland cement phases

DEFF Research Database (Denmark)

Wesselsky, Andreas; Jensen, Ole Mejlhede

2009-01-01

Pure phases commonly found in Portland cement clinkers are often used to test cement hydration behaviour in simplified experimental conditions. The synthesis of these phases is covered in this paper, starting with a description of phase relations and possible polymorphs of the four main phases...... in Portland cement, i.e. tricalcium silicate, dicalcium silicate, tricalcium aluminate and tetracalcium alumino ferrite. Details of the The process of solid state synthesis are is described in general including practical advice on equipment and techniques. Finally In addition, some exemplary mix compositions...

Remediation System Evaluation, McCormick and Baxter Superfund SiteRemediation System Evaluation, McCormick and Baxter Superfund Site

Science.gov (United States)

The McCormick and Baxter Creosoting Company, Portland Plant, Superfund Site is located adjacent tothe Willamette River in Portland, Oregon and addresses contamination of soil, groundwater, and riversediments stemming from creosoting operations...

Binding of chloride and alkalis in Portland cement systems

International Nuclear Information System (INIS)

Nielsen, Erik P.; Herfort, Duncan; Geiker, Mette R.

2005-01-01

A thermodynamic model for describing the binding of chloride and alkalis in hydrated Portland cement pastes has been developed. The model is based on the phase rule, which for cement pastes in aggressive marine environment predicts multivariant conditions, even at constant temperature and pressure. The effect of the chloride and alkalis has been quantified by experiments on cement pastes prepared from white Portland cements containing 4% and 12% C 3 A, and a grey Portland cement containing 7% C 3 A. One weight percent calcite was added to all cements. The pastes prepared at w/s ratio of 0.70 were stored in solutions of different Cl (CaCl 2 ) and Na (NaOH) concentrations. When equilibrium was reached, the mineralogy of the pastes was investigated by EDS analysis on the SEM. A well-defined distribution of chloride was found between the pore solution, the C-S-H phase, and an AFm solid solution phase consisting of Friedel's salt and monocarbonate. Partition coefficients varied as a function of iron and alkali contents. The lower content of alkalis in WPC results in higher chloride contents in the C-S-H phase. High alkali contents result in higher chloride concentrations in the pore solution

New Approaches to Tsunami Hazard Mitigation Demonstrated in Oregon

Science.gov (United States)

Priest, G. R.; Rizzo, A.; Madin, I.; Lyles Smith, R.; Stimely, L.

2012-12-01

methods were: (1) door-to-door (person-to-person) education, (2) evacuation drills, (3) outreach to K-12 schools, (4) media events, and (5) workshops targeted to key audiences (lodging facilities, teachers, and local officials). Community organizers were hired to apply these five methods to clusters of small communities, measuring performance by before and after polling. Organizers were encouraged to approach the top priority, person-to-person education, by developing Community Emergency Response Teams (CERT) or CERT-like organizations in each community, thereby leaving behind a functioning volunteer-based group that will continue the outreach program and build long term resiliency. One of the most effective person-to-person educational tools was the Map Your Neighborhood program that brings people together so they can sketch the basic layout of their neighborhoods to depict key earthquake and tsunami hazards and mitigation solutions. The various person-to-person volunteer efforts and supporting outreach activities are knitting communities together and creating a permanent culture of tsunami and earthquake preparedness. All major Oregon coastal population centers will have been covered by this intensive outreach program by ~2014.

Analyses of heavy metals in mineral trioxide aggregate and Portland cement.

Science.gov (United States)

Schembri, Matthew; Peplow, George; Camilleri, Josette

2010-07-01

Portland cement is used in the construction industry as a binder in concrete. It is manufactured from chalk, limestone, and clay, which are clinkered at very high temperatures and ground with gypsum to form Portland cement. The raw materials and the manufacturing process can result in the inclusion of heavy metals in Portland cement. Portland cement with a four to one addition of bismuth oxide is marketed as mineral trioxide aggregate (MTA), which is used mainly as a dental material. Heavy metal inclusion can be of concern because MTA is in contact with hard and soft tissues. Measurements of arsenic, lead, and chromium in hydrated gray and white Portland cement, ProRoot MTA, and MTA Angelus were conducted with graphite furnace atomic absorption spectrophotometry after acid digestion on the hydrated material. The leaching of the metal ions from the solid material in water and simulated body fluid (SBF) was also determined. All cement types showed high relative values of leached chromium compared with arsenic and lead in both the total metal content and leached species. The gray Portland cement showed the highest total amount of metal. The white Portland and both MTAs had lower values for all the leached metal ions. Both MTAs released more arsenic than the amount specified in ISO 9917-1 (2007). Portland cements and MTAs showed evidence of heavy metals in the acid-soluble form as well as leaching in deionized water and SBF. MTA contained levels of arsenic higher than the safe limit specified by the ISO 9917-1 (2007). Copyright 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Low porosity portland cement pastes based on furan polymers

International Nuclear Information System (INIS)

Darweesh, H.H.M.

2005-01-01

The effect of three different types of Furan polymers on the porosity, mechanical properties, mechanism of hydration and microstructure of Ordinary Portland cement (OPC) pastes was investigated. The results showed that mixing the OPC with Furan polymers, the standard water of consistency of the different cement pastes decreases and therefore the setting times (initial and final) are shortened. The total porosity of the hardened cement pastes decreased, while the mechanical properties improved and enhanced at all curing ages of hydration compared with those of the pure OPC pastes. The hydration process with Furan polymers proceeded according to the following decreasing order: F.ac. > F.ph. > F.alc. > OPC

Effect of blended materials on U(VI) retention characteristics for portland cement solidification product

International Nuclear Information System (INIS)

Tan Hongbin; Ma Xiaoling; Li Yuxiang

2006-01-01

Using the simulated groundwater as leaching liquid, the retention capability of U(VI) in solidification products with Portland cement, the Portland cement containing silica fume, the Portland cement containing metakaolin and the Portland cement containing fly ash was researched by leaching experiments at 25 degree C for 42 d. The results indicate silica fume and metakaolin as blended materials can improve the U(VI) retention capability of Portland cement solidification product, but fly ash can not. (authors)

Hydration kinetics modeling of Portland cement considering the effects of curing temperature and applied pressure

International Nuclear Information System (INIS)

Lin Feng; Meyer, Christian

2009-01-01

A hydration kinetics model for Portland cement is formulated based on thermodynamics of multiphase porous media. The mechanism of cement hydration is discussed based on literature review. The model is then developed considering the effects of chemical composition and fineness of cement, water-cement ratio, curing temperature and applied pressure. The ultimate degree of hydration of Portland cement is also analyzed and a corresponding formula is established. The model is calibrated against the experimental data for eight different Portland cements. Simple relations between the model parameters and cement composition are obtained and used to predict hydration kinetics. The model is used to reproduce experimental results on hydration kinetics, adiabatic temperature rise, and chemical shrinkage of different cement pastes. The comparisons between the model reproductions and the different experimental results demonstrate the applicability of the proposed model, especially for cement hydration at elevated temperature and high pressure.

Tectonic evolution of the Tualatin basin, northwest Oregon, as revealed by inversion of gravity data

Science.gov (United States)

McPhee, Darcy K.; Langenheim, Victoria E.; Wells, Ray; Blakely, Richard J.

2014-01-01

The Tualatin basin, west of Portland (Oregon, USA), coincides with a 110 mGal gravity low along the Puget-Willamette lowland. New gravity measurements (n = 3000) reveal a three-dimensional (3-D) subsurface geometry suggesting early development as a fault-bounded pull-apart basin. A strong northwest-trending gravity gradient coincides with the Gales Creek fault, which forms the southwestern boundary of the Tualatin basin. Faults along the northeastern margin in the Portland Hills and the northeast-trending Sherwood fault along the southeastern basin margin are also associated with gravity gradients, but of smaller magnitude. The gravity low reflects the large density contrast between basin fill and the mafic crust of the Siletz terrane composing basement. Inversions of gravity data indicate that the Tualatin basin is ∼6 km deep, therefore 6 times deeper than the 1 km maximum depth of the Miocene Columba River Basalt Group (CRBG) in the basin, implying that the basin contains several kilometers of low-density pre-CRBG sediments and so formed primarily before the 15 Ma emplacement of the CRBG. The shape of the basin and the location of parallel, linear basin-bounding faults along the southwest and northeast margins suggest that the Tualatin basin originated as a pull-apart rhombochasm. Pre-CRBG extension in the Tualatin basin is consistent with an episode of late Eocene extension documented elsewhere in the Coast Ranges. The present fold and thrust geometry of the Tualatin basin, the result of Neogene compression, is superimposed on the ancestral pull-apart basin. The present 3-D basin geometry may imply stronger ground shaking along basin edges, particularly along the concealed northeast edge of the Tualatin basin beneath the greater Portland area.

Site Investigation at the 142nd Fighter Interceptor Group, Oregon Air National Guard, Portland International Airport, Portland, Oregon

Science.gov (United States)

1991-05-17

west toward the drainage ditch along Hannis Street. In either case, the surface water .:iid eventually drain into the main base drainage ditches which...storm drain inlets are fairly distant: 300 ft to the west along Hannis Street and 500 ft to the southeast along Chin Street. Both of these storm...SIE3IUHHUEAE RVOSSMLN OAIN Main POTAD PRLNsePOTANOEO S! Report Revision 3 17 May 1991 38 of 214 side of Hannis e Surface water in this ditch enters a culvert

A comparative evaluation of compressive strength of Portland cement with zinc oxide eugenol and Polymer-reinforced cement: an in vitro analysis.

Science.gov (United States)

Prakasam, S; Bharadwaj, Prakasam; Loganathan, S C; Prasanth, B Krishna

2014-01-01

The purpose of this study is to evaluate the ultimate compressive strength of 50% and 25% Portland cement mixed with Polymer-reinforced zinc oxide eugenol and zinc oxide eugenol cement after 1 hour, 24 hours, and 7 days. One hundred and eighty samples were selected. The samples were made cylindrical of size 6 × 8 mm and were divided into six groups as follows with each group consisting of 10 samples. Group 1: Polymer-reinforced zinc oxide eugenol with 50% Portland cement (PMZNPC 50%) Group 2: Polymer-reinforced zinc oxide eugenol with 25% Portland cement (PMZNPC 25%) Group 3: Polymer-reinforced zinc oxide eugenol with 0% Portland cement (PMZNPC 0%) Group 4: Zinc oxide eugenol with 50% Portland cement (ZNPC 50%) Group 5: Zinc oxide eugenol with 25% Portland cement (ZNPC 25%) Group 6: Zinc oxide eugenol with 0% Portland cement (ZNPC 0%) These samples were further subdivided based on time interval and were tested at 1 hour, 24 hours and at 7 th day. After each period of time all the specimens were tested by vertical CVR loaded frame with capacity of 5 tones/0473-10kan National Physical laboratory, New Delhi and the results were statistically analyzed using ANOVA and Scheffe test. Polymer-reinforced cement with 50% Portland cement, Zinc oxide with 50% Portland cement, Polymer-reinforced cement with 25% Portland cement and Zinc oxide with 25% Portland cement exhibited higher compressive strength when compared to Zinc oxide with 0% Portland cement and Polymer-reinforced cement with 0% Portland cement, at different periods of time. The difference between these two groups were statistically significant (P Portland cement in Zinc oxide eugenol and Polymer-modified zinc oxide cement can be used as core build up material and permanent filling material. It is concluded that 50% and 25% Portland cement in zinc oxide eugenol and polymer-modified zinc oxide eugenol results in higher compressive strength and hence can be used as permanent filling material and core built

76 FR 28318 - National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing...

Science.gov (United States)

2011-05-17

... Cement Manufacturing Industry and Standards of Performance for Portland Cement Plants AGENCY... Emission Standards for Hazardous Air Pollutants from the Portland Cement Manufacturing Industry Response to... by the Portland Cement Industry and the New Source Performance Standards for Portland Cement Plants...

76 FR 2832 - National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing...

Science.gov (United States)

2011-01-18

... Cement Manufacturing Industry and Standards of Performance for Portland Cement Plants AGENCY...) from the Portland Cement Manufacturing Industry and Standards of Performance (NSPS) for Portland Cement... Standards for Hazardous Air Pollutant From the Portland Cement Manufacturing Industry Docket, Docket ID No...

Setting time and flowability of accelerated Portland cement mixed with polycarboxylate superplasticizer.

Science.gov (United States)

Wongkornchaowalit, Norachai; Lertchirakarn, Veera

2011-03-01

Important limitations of mineral trioxide aggregate for use in clinical procedures are extended setting time and difficult handling characteristics. The removal of gypsum at the end stage of the Portland cement manufacturing process and polycarboxylate superplasticizer admixture may solve these limitations. Different concentrations of polycarboxylate superplasticizer (0%, 1.2%, 1.8%, and 2.4% by volume) and liquid-to-powder ratios (0.27, 0.30, and 0.33 by weight) were mixed with white Portland cement without gypsum (AWPC-experimental material). Type 1 ordinary white Portland cement mixed with distilled water at the same ratios as the experimental material was used as controls. All samples were tested for setting time and flowability according to the International Organization for Standardization 6876:2001 guideline. The data were analyzed by two-way analysis of variance. Then, one-way analysis of variance and multiple comparison tests were used to analyze the significance among groups. The data are presented in mean ± standard deviation values. In all experimental groups, the setting times were in the range of 4.2 ± 0.4 to 11.3 ± 0.2 minutes, which were significantly (p setting time and increased flowability of cement, which would be beneficial for clinical use. Copyright © 2011 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Investigating organic matter in Fanno Creek, Oregon, Part 2 of 3: sources, sinks, and transport of organic matter with fine sediment

Science.gov (United States)

Keith, Mackenzie K.; Sobieszczyk, Steven; Goldman, Jami H.; Rounds, Stewart A.

2014-01-01

Organic matter (OM) is abundant in Fanno Creek, Oregon, USA, and has been tied to a variety of water-quality concerns, including periods of low dissolved oxygen downstream in the Tualatin River, Oregon. The key sources of OM in Fanno Creek and other Tualatin River tributaries have not been fully identified, although isotopic analyses from previous studies indicated a predominantly terrestrial source. This study investigates the role of fine sediment erosion and deposition (mechanisms and spatial patterns) in relation to OM transport. Geomorphic mapping within the Fanno Creek floodplain shows that a large portion (approximately 70%) of the banks are eroding or subject to erosion, likely as a result of the imbalance caused by anthropogenic alteration. Field measurements of long- and short-term bank erosion average 4.2 cm/year and average measurements of deposition for the watershed are 4.8 cm/year. The balance between average annual erosion and deposition indicates an export of 3,250 metric tons (tonnes, t) of fine sediment to the Tualatin River—about twice the average annual export of 1,880 t of sediment at a location 2.4 km from the creek’s mouth calculated from suspended sediment load regressions from continuous turbidity data and suspended sediment samples. Carbon content from field samples of bank material, combined with fine sediment export rates, indicates that about 29–67 t of carbon, or about 49–116 t of OM, from bank sediment may be exported to the Tualatin River from Fanno Creek annually, an estimate that is a lower bound because it does not account for the mass wasting of organic-rich O and A soil horizons that enter the stream.

Physicochemical Properties of MTA and Portland Cement after Addition of Aloe Vera.

Science.gov (United States)

Henrique Borges, Alvaro; Aguirre Guedes, Orlando; Evaristo Ricci Volpato, Luiz; Siebert Filho, Gilberto; Meireles Borba, Alexandre; Zina, Omar; Piva, Evandro; Estrela, Carlos

2017-01-01

The aim of this in vitro study was to determine the liquid-powder ratio, setting time, solubility, dimensional change, pH, and radiopacity of white structural and non-structural Portland cement, ProRoot MTA and MTA Bio, associated with a 2% glycolic solution containing Aloe Vera, as vehicle. Five samples of each material were used for each test, according to the American National Standards Institute/American Dental Association (ANSI/ADA) specification No. 57. Statistical analyses were performed using ANOVA and Tukey's test at 5% significance. When sample distribution was not normal, non-parametric analysis of variance and the Kruskal-Wallis test were used ( α =0.05). No statistical differences were found in liquid-powder ratios among the tested materials. ProRoot MTA showed the longest setting time. Dimensional change values were acceptable in all groups. Also, no significant differences were found in pH values and pH was alkaline in all samples throughout the experiment. Mean radiopacity results obtained for white Portland cements did not meet ANSI/ADA requirements, and were significantly lower than those obtained for MTA-based cements. Finally, Portland cements showed significantly higher mean solubility values compared to the other samples. The physicochemical properties of the tested materials in association with Aloe Vera were compatible with ANSI/ADA requirements, except for the white Portland cements, which failed to meet the radiopacity specification.

77 FR 46371 - National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing...

Science.gov (United States)

2012-08-03

...-AQ93 National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing... Portland Cement Manufacturing Industry and Standards of Performance for Portland Cement Plants,'' which was... Manufacturing Industry and Standards of Performance for Portland Cement Plants'' under Docket ID No. EPA-HQ-OAR...

Geochemical ecosystem engineering by the mud shrimp Upogebia pugettensis (Crustacea: Thalassinidae) in Yaquina Bay, Oregon: density-dependent effects on organic matter remineralization and nutrient cycling

Science.gov (United States)

We investigated the effect of the thalassinid mud shrimp Upogebia pugettensis on organic matter and nutrient cycling on Idaho Flat, an intertidal flat in the Yaquina River estuary, Oregon. Field studies were conducted to measure carbon and nitrogen remineralization rates and bent...

An Annual Report to the Legislature on Oregon Public Schools. Oregon Statewide Report Card. 2014-2015

Science.gov (United States)

Oregon Department of Education, 2015

2015-01-01

The Oregon Statewide Report Card is an annual publication required by law (ORS 329.115), which reports on the state of public schools and their progress towards the goals of the Oregon Educational Act for the 21st Century. The purpose of the Oregon Report Card is to monitor trends among school districts and Oregon's progress toward achieving the…

Immediate and delayed solubility of mineral trioxide aggregate and Portland cement

Directory of Open Access Journals (Sweden)

Augusto Bodanezi

2008-04-01

Full Text Available This study investigated the solubility of mineral trioxide aggregate (MTA and Portland cement since its mixture until 672 hours, by means of two complimentary methods. Metal ring molds filled with the cements were covered with distilled water and, at each experimental time (3, 24, 72, 168, 336 and 672 hours, were weighed as soon as the plates in which the samples have been placed. Empty rings served as the control group (n=8. Mean weight gain and loss was determined and analyzed statistically by two-way ANOVA and Tukey's test for all pairwise comparisons. Only Portland cement showed less than 3% weight loss through 24 hours. Detached MTA residues were heavier than those of Portland cement over the 3 to 168 hours. The weight of MTA rings increased more than that of Portland rings within 672 hours (p=0.05. The findings of the present study indicate that, in an aqueous environment MTA is more soluble than Portland cement and exceeds the maximum weight loss considered acceptable by ISO 6876 standard (2001.

Immediate and delayed solubility of mineral trioxide aggregate and Portland cement.

Science.gov (United States)

Bodanezi, Augusto; Carvalho, Nara; Silva, Daniela; Bernardineli, Norberti; Bramante, Clovis Monteiro; Garcia, Roberto Brandão; de Moraes, Ivaldo Gomes

2008-01-01

This study investigated the solubility of mineral trioxide aggregate (MTA) and Portland cement since its mixture until 672 hours, by means of two complimentary methods. Metal ring molds filled with the cements were covered with distilled water and, at each experimental time (3, 24, 72, 168, 336 and 672 hours), were weighed as soon as the plates in which the samples have been placed. Empty rings served as the control group (n=8). Mean weight gain and loss was determined and analyzed statistically by two-way ANOVA and Tukey's test for all pairwise comparisons. Only Portland cement showed less than 3% weight loss through 24 hours. Detached MTA residues were heavier than those of Portland cement over the 3 to 168 hours. The weight of MTA rings increased more than that of Portland rings within 672 hours (p=0.05). The findings of the present study indicate that, in an aqueous environment MTA is more soluble than Portland cement and exceeds the maximum weight loss considered acceptable by ISO 6876 standard (2001).

Presence of arsenic in different types of MTA and white and gray Portland cement.

Science.gov (United States)

Monteiro Bramante, Clóvis; Demarchi, Ana Claudia Cardoso Oliveira; de Moraes, Ivaldo Gomes; Bernadineli, Norberti; Garcia, Roberto Brandão; Spångberg, Lars S W; Duarte, Marco Antonio Hungaro

2008-12-01

The presence of arsenic in various types of mineral trioxide aggregate (MTA) and Portland cements were evaluated to verify if they comply with the ISO-recommended limit for water-based cements of 2 mg arsenic/kg material. An amount of 5 mL of hydrochloric acid was added to 2 g each of MTA and Portland cement to be analyzed. After 15 minutes, the material was filtered and the volume of supernatant was diluted with reagent-grade water up to 40 mL. Atomic absorption spectrophotometry readings were performed in triplicate. The following mean values were obtained: CPM (Egeo, Buenos Aires, Argentina) 11.06 mg/kg; CPM sealer (Egeo) 10.30 mg/kg; MTA-Obtura (Angelus, Londrina, PR, Brazil) 0.39 mg/kg; Experimental MTA: 10.30 mg/kg; White MTA-Angelus (Angelus) 1.03 mg/kg; Gray MTA-Angelus (Angelus) 5.91 mg/kg; ProRoot-MTA (Dentsply/Tulsa Dental Specialties, Tulsa, OK) 5.25 mg/kg; Gray Portland cement (Votorantim Cimentos, Cubatão, SP, Brazil): 34.27 mg/kg; and White Portland cement (Cimento Rio Branco, Rio de Janeiro, RJ, Brazil) 0.52 mg/kg. All tested materials presented arsenic in their composition. The form of arsenic was not analyzed nor the toxicity of the arsenic found. Only MTA-Obtura, White MTA-Angelus, and White Portland cement presented arsenic levels below the limit set in the ISO 9917-1 standard.

Prediction of potential compressive strength of Portland clinker from its mineralogy

DEFF Research Database (Denmark)

Svinning, K.; Høskuldsson, Agnar; Justnes, H.

2010-01-01

Based on a statistical model first applied for prediction of compressive strength up to 28 d from the microstructure of Portland cement, potential compressive strength of clinker has been predicted from its mineralogy. The prediction model was evaluated by partial least squares regression...

Portland cement hydration in the presence of admixtures: black gram pulse and superplasticizer

Directory of Open Access Journals (Sweden)

Viveka Nand Dwivedi

2008-12-01

Full Text Available Effect of admixtures such as black gram pulse (BGP and sulfonated naphthalene based superplasticizer (SP on the hydration of Portland cement has been studied. The hydration characteristics of OPC in the presence of BGP and SP were studied with the help of non evaporable water content determinations, calorimetric method, Mössbauer spectroscopic and atomic force microscopic techniques. Results have shown that both BGP and SP get adsorbed at the surface of cement and its hydration products. The hydration of Portland cement is retarded in the presence of both the admixtures and nanosize hydration products are formed.

Improved quantification of alite and belite in anhydrous Portland cements by 29Si MAS NMR: Effects of paramagnetic ions

DEFF Research Database (Denmark)

Poulsen, Søren Lundsted; Kocaba, Vanessa; Le Saoût, Gwenn

2009-01-01

The applicability, reliability, and repeatability of 29Si MAS NMR for determination of the quantities of alite (Ca3SiO5) and belite (Ca2SiO4) in anhydrous Portland cement was investigated in detail for 11 commercial Portland cements and the results compared with phase quantifications based...

77 FR 62442 - Safety Zone; Oregon City Bridge Grand Opening Fireworks Display; Willamette River, Oregon City, OR

Science.gov (United States)

2012-10-15

... 1625-AA00 Safety Zone; Oregon City Bridge Grand Opening Fireworks Display; Willamette River, Oregon... establishing a safety zone on the Willamette River between the Oregon City Bridge and the Interstate 205 Bridge... established on the Willamette River from shore to shore between the Oregon City Bridge and the Interstate 205...

Selected elements and organic chemicals in streambed sediment in the Salem area, Oregon, 1999

Science.gov (United States)

Tanner, Dwight Q.

2002-09-13

Analysis of streambed sediments in the Salem, Oregon, area showed anomalously large concentrations of some elements and organic chemicals, indicating contamination from anthropogenic and/or geologic sources. The streambed sediment sample from Clark Creek, an urban basin, had large concentrations of polycyclic aromatic hyrdocarbons (PAHs), organochlorines, cadmium, lead, and zinc. The sample from the East Fork of Pringle Creek, which is a mostly urban basin, had the highest concentrations of DDD, DDE, and DDT compounds. Aldrin was detected in streambed sediment at only one site, the East Fork of Pringle Creek. Ten of the 14 sites sampled had exceedances of the sediment quality guidelines of the Canadian Council of Ministers of the Environment (CCME), and 8 sites had exceedances of guidelines from the Puget Sound Dredged Disposal Analysis (PSDDA) Program.

The Oregon Geothermal Planning Conference

Energy Technology Data Exchange (ETDEWEB)

None

1980-10-02

Oregon's geothermal resources represent a large portion of the nation's total geothermal potential. The State's resources are substantial in size, widespread in location, and presently in various stages of discovery and utilization. The exploration for, and development of, geothermal is presently dependent upon a mixture of engineering, economic, environmental, and legal factors. In response to the State's significant geothermal energy potential, and the emerging impediments and incentives for its development, the State of Oregon has begun a planning program intended to accelerate the environmentally prudent utilization of geothermal, while conserving the resource's long-term productivity. The program, which is based upon preliminary work performed by the Oregon Institute of Technology's Geo-Heat Center, will be managed by the Oregon Department of Energy, with the assistance of the Departments of Economic Development, Geology and Mineral Industries, and Water Resources. Funding support for the program is being provided by the US Department of Energy. The first six-month phase of the program, beginning in July 1980, will include the following five primary tasks: (1) coordination of state and local agency projects and information, in order to keep geothermal personnel abreast of the rapidly expanding resource literature, resource discoveries, technological advances, and each agency's projects. (2) Analysis of resource commercialization impediments and recommendations of incentives for accelerating resource utilization. (3) Compilation and dissemination of Oregon geothermal information, in order to create public and potential user awareness, and to publicize technical assistance programs and financial incentives. (4) Resource planning assistance for local governments in order to create local expertise and action; including a statewide workshop for local officials, and the formulation of two specific community resource development

Electrically conductive Portland cement concrete.

Science.gov (United States)

1986-01-01

There is a need for an effective, simple-to-install secondary anode system for use in the cathodic protection of reinforced concrete bridge decks. In pursuit of such a system, carbon fibers and carbon black were incorporated in portland cement concre...

AC/CRC adjacent lane surfacing : construction report.

Science.gov (United States)

1991-06-01

Asphaltic Concrete (AC) and Portland Cement Concrete (PCC) are common roadway materials used in Oregon. In a recent construction project -- Poverty Flats/Mecham Section -- the Oregon State Highway Division (OSHD) designed, as part of the project, a "...

Overview for geologic field-trip guides to Mount Mazama, Crater Lake Caldera, and Newberry Volcano, Oregon

Science.gov (United States)

Bacon, Charles R.; Donnelly-Nolan, Julie M.; Jensen, Robert A.; Wright, Heather M.

2017-08-16

These field-trip guides were written for the occasion of the International Association of Volcanology and Chemistry of the Earth’s Interior (IAVCEI) quadrennial scientific assembly in Portland, Oregon, in August 2017. The guide to Mount Mazama and Crater Lake caldera is an updated and expanded version of the guide (Bacon, 1989) for part of an earlier IAVCEI trip to the southern Cascade Range. The guide to Newberry Volcano describes the stops included in the 2017 field trip. Crater Lake and Newberry are the two best-preserved and most recent calderas in the Cascades Volcanic Arc. Although located in different settings in the arc, with Crater Lake on the arc axis and Newberry in the rear-arc, both volcanoes are located at the intersection of the arc and the northwest corner region of the extensional Basin and Range Province.

2013 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Clackamol

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI collected Light Detection and Ranging (LiDAR) data for the Oregon LiDAR Consortium (OLC) Clackamol 2013 study area in Clackamas and Marion County, Oregon. The...

Comparative study of physico-chemical properties of MTA-based and Portland cements.

Science.gov (United States)

Borges, Alvaro H; Pedro, Fábio L M; Miranda, Carlos E S; Semenoff-Segundo, Alex; Pécora, Jesus D; Filho, Antônio M Cruz

2010-01-01

The purpose of this investigation was to evaluate the physicochemical properties of gray and white structural and nonstructural Portland cement, gray and white ProRoot MTA and MTA BIO. The water/powder ratio, setting time, solubility and pH (hydrogen-ion potential) changes of the materials were evaluated. Tests followed specification #57 from the American National Standard Institute/American Dental Association (2000) for endodontic sealing materials and pH was determined by a digital pH meter. The test results were statistically analyzed by variance analyses for global comparison and by the complementary Tukey's test for pairwise comparisons (5%). Considering the water/powder ratio, no significant difference (p > 0.05) was observed among the cements. MTA BIO (33.10 +/- 2.30) had the lowest setting time (p Portland cement (2.55 +/- 0.08) had the highest solubility (p 0.05) was observed among materials when considering pH evaluation. The pH levels were highly alkaline immediately after immersion in solution, remaining stable throughout the test period. The authors conclude that the cements had similar water/powder proportions. MTA BIO had the shortest setting time and gray ProRoot MTA had the lowest solubility. All cements had similar behavior in the pH analysis.

South Oregon Coast Reinforcement.

Energy Technology Data Exchange (ETDEWEB)

United States. Bonneville Power Administration.

1998-05-01

The Bonneville Power Administration is proposing to build a transmission line to reinforce electrical service to the southern coast of Oregon. This FYI outlines the proposal, tells how one can learn more, and how one can share ideas and opinions. The project will reinforce Oregon`s south coast area and provide the necessary transmission for Nucor Corporation to build a new steel mill in the Coos Bay/North Bend area. The proposed plant, which would use mostly recycled scrap metal, would produce rolled steel products. The plant would require a large amount of electrical power to run the furnace used in its steel-making process. In addition to the potential steel mill, electrical loads in the south Oregon coast area are expected to continue to grow.

Field-trip guide to the vents, dikes, stratigraphy, and structure of the Columbia River Basalt Group, eastern Oregon and southeastern Washington

Science.gov (United States)

Camp, Victor E; Reidel, Stephen P.; Ross, Martin E.; Brown, Richard J.; Self, Stephen

2017-06-22

The Columbia River Basalt Group covers an area of more than 210,000 km2 with an estimated volume of 210,000 km3. As the youngest continental flood-basalt province on Earth (16.7–5.5 Ma), it is well preserved, with a coherent and detailed stratigraphy exposed in the deep canyonlands of eastern Oregon and southeastern Washington. The Columbia River flood-basalt province is often cited as a model for the study of similar provinces worldwide.This field-trip guide explores the main source region of the Columbia River Basalt Group and is written for trip participants attending the 2017 International Association of Volcanology and Chemistry of the Earth’s Interior (IAVCEI) Scientific Assembly in Portland, Oregon, USA. The first part of the guide provides an overview of the geologic features common in the Columbia River flood-basalt province and the stratigraphic terminology used in the Columbia River Basalt Group. The accompanying road log examines the stratigraphic evolution, eruption history, and structure of the province through a field examination of the lavas, dikes, and pyroclastic rocks of the Columbia River Basalt Group.

Thermophysical properties of blends from Portland and sulfoaluminate-belite cements

International Nuclear Information System (INIS)

Mojumdar, S.C.; Janotka, I.

2002-01-01

The behavior of mortars with blends consisting of sulfoaluminate-belite cements and ordinary Portland cement made with cement to sand ratio of 1:3 by weight and w/c = 0.5 maintained for 90 days at 20 0 C either at 60% relative humidity - dry air or 100% relative humidity - wet air. The results show insufficient character of hydraulic activity of sulfoaluminate-belite cements. Their quality has been improved. The replacement of 15 wt % of sulfoaluminate-belite cement by ordinary Portland cement influences strength positively and elasticity modulus values as well as hydrated phases and pore structure development of sulfoaluminate-belite/ordinary Portland cement blends relative to pure sulfoaluminate-belite cement systems. The above statements confirm the possible making technologies, when improvements in sulfoaluminate-belite cements quality will be achieved. One would then anticipate the competition in usages between sulfoaluminate-belite/ordinary Portland cement and blast furnace-slag Portland cement systems in the practice. It is important to consider because sulfoaluminate-belite cements are of great advantage from the viewpoint of energy savings and quantity of CO 2 released during their production. Thermal characteristics of the samples were studied by thermogravimetry and differential thermal analysis from room temperature to 1000 0 C in air atmosphere. Generally, four significant temperature regions on thermogravimetry curves with the respective differential thermal analysis peak temperature for all types of samples are observed (Authors)

Experimental study of chloride diffusivity in unsaturated ordinary Portland cement mortar

NARCIS (Netherlands)

Zhang, Y.; Ye, G.; Santhanam, M.

2017-01-01

Experiments are carried out to investigate the chloride diffusivity in partially saturated ordinary Portland cement mortars with water-to-cement (w/c) ratios of 0.4, 0.5 and 0.6. Based on resistivity measurement and Nernst-Einstein equation, the chloride diffusivities of cement mortars at various

Portland cement versus MTA as a root-end filling material. A pilot study.

Science.gov (United States)

da Silva, Sérgio Ribeiro; da Silva Neto, José Dias; Veiga, Daniela Francescato; Schnaider, Taylor Brandão; Ferreira, Lydia Masako

2015-02-01

To assess periradicular lesions clinically and by computed tomography (CT) after endodontic surgery using either Portland cement or mineral trioxide aggregate (MTA) as a root-end filling material. Three patients diagnosed with periradicular lesions by cone-beam CT underwent endodontic surgery with root-end filling. Patient A was treated with MTA as the root-end filling material, patient B was treated with Portland cement and patient C had two teeth treated, one with MTA and the other with Portland cement. Six months after surgery, the patients were assessed clinically and by CT scan and the obtained results were compared. Periradicular tissue regeneration was observed in all cases, with no significant differences in bone formation when comparing the use of MTA and Portland cement as root-end filling materials. Both mineral trioxide aggregate and Portland cement were successful in the treatment of periradicular lesions.

African refugee and immigrant health needs: report from a community-based house meeting project.

Science.gov (United States)

Boise, Linda; Tuepker, Anais; Gipson, Teresa; Vigmenon, Yves; Soule, Isabelle; Onadeko, Sade

2013-01-01

As in other communities in the United States, information is lacking about the health needs of Africans refugees and immigrants living in Portland, Oregon. In 2008, the African Partnership for Health coalition (APH) was formed to carry out research, advocacy and education to improve the health and well-being of Africans in Oregon. This was APH's initial project. The purposes of this study were to gather data about the perceived health needs and barriers to health care Africans encounter, and lay the foundation for a program of action to guide APH's future work. Community-based participatory research (CBPR) methods were used to collect data on how to improve the health of the African community in the Portland area and define an agenda for future projects. Popular education principles guided the engagement and training of African community members, who conducted nine house meetings with 56 Africans from 14 countries. The results were analyzed by African community members and researchers and prioritized at a community meeting. Three themes emerged: The stressfulness of life in America, the challenges of gaining access to health care, and the pervasive feelings of disrespect and lack of understanding of Africans' health needs, culture, and life experiences by health providers and staff members. Using CBPR methods, we identified and prioritized the needs of the African community. This information provides a framework for future work of the African Partnership for Health and other service and advocacy groups.

Timber resource statistics for Oregon.

Science.gov (United States)

Sally Campbell; Paul Dunham; David. Azuma

2004-01-01

This report is a summary of timber resource statistics for all ownerships in Oregon. Data were collected as part of several statewide multiresource inventories, including those conducted by the Pacific Northwest Region (Region 6) on National Forest System lands in Oregon, by the Bureau of Land Management (BLM) on BLM lands in western Oregon, and by the Pacific...

40 CFR 81.78 - Metropolitan Portland Intrastate Air Quality Control Region.

Science.gov (United States)

2010-07-01

... Quality Control Region. 81.78 Section 81.78 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.78 Metropolitan Portland Intrastate Air Quality Control Region. The Metropolitan Portland Intrastate Air Quality Control Region (Maine) consists of the territorial area...

Hydrology of the Johnson Creek Basin, Oregon

Science.gov (United States)

Lee, Karl K.; Snyder, Daniel T.

2009-01-01

The Johnson Creek basin is an important resource in the Portland, Oregon, metropolitan area. Johnson Creek forms a wildlife and recreational corridor through densely populated areas of the cities of Milwaukie, Portland, and Gresham, and rural and agricultural areas of Multnomah and Clackamas Counties. The basin has changed as a result of agricultural and urban development, stream channelization, and construction of roads, drains, and other features characteristic of human occupation. Flooding of Johnson Creek is a concern for the public and for water management officials. The interaction of the groundwater and surface-water systems in the Johnson Creek basin also is important. The occurrence of flooding from high groundwater discharge and from a rising water table prompted this study. As the Portland metropolitan area continues to grow, human-induced effects on streams in the Johnson Creek basin will continue. This report provides information on the groundwater and surface-water systems over a range of hydrologic conditions, as well as the interaction these of systems, and will aid in management of water resources in the area. High and low flows of Crystal Springs Creek, a tributary to Johnson Creek, were explained by streamflow and groundwater levels collected for this study, and results from previous studies. High flows of Crystal Springs Creek began in summer 1996, and did not diminish until 2000. Low streamflow of Crystal Springs Creek occurred in 2005. Flow of Crystal Springs Creek related to water-level fluctuations in a nearby well, enabling prediction of streamflow based on groundwater level. Holgate Lake is an ephemeral lake in Southeast Portland that has inundated residential areas several times since the 1940s. The water-surface elevation of the lake closely tracked the elevation of the water table in a nearby well, indicating that the occurrence of the lake is an expression of the water table. Antecedent conditions of the groundwater level and autumn

EnviroAtlas - Portland, OR - Meter-Scale Urban Land Cover (MULC) Data (2012)

Data.gov (United States)

U.S. Environmental Protection Agency — The EnviroAtlas Portland, OR Meter-Scale Urban Land Cover (MULC) dataset includes data for the Portland metropolitan area plus the city of Vancouver, Washington and...

Biocompatibility of Portland cement combined with different radiopacifying agents.

Science.gov (United States)

Lourenço Neto, Natalino; Marques, Nádia C T; Fernandes, Ana Paula; Rodini, Camila O; Duarte, Marco A H; Lima, Marta C; Machado, Maria A A M; Abdo, Ruy C C; Oliveira, Thais M

2014-03-01

The aim of this study was to evaluate the response of rat subcutaneous tissue to Portland cement combined with two different radiopacifying agents, iodoform (CHI3) and zirconium oxide (ZrO2). These materials were placed in polyethylene tubes and implanted into the dorsal connective tissue of Wistar rats for 7 and 15 days. The specimens were then stained with hematoxylin and eosin, and inflammatory reaction parameters were evaluated by light microscopy. The intensity of the inflammatory response to the sealants was analyzed by two blind calibrated observers throughout the experimental period. Histological analysis showed that all the materials caused a moderated inflammatory reaction at 7 days, which then diminished with time. At 15 days, the inflammatory reaction was almost absent, and fibroblasts and collagen fibers were observed indicating normal tissue healing. The degrees of the inflammatory reaction on different days throughout the experimental period were compared using the non-parametric Kruskal-Wallis test. Statistical analysis demonstrated no significant differences amongst the groups, and Portland cement associated with radiopacifying agents gave satisfactory results. Therefore, Portland cement used in combination with radiopacifying agents can be considered a biocompatible material. Although our results are very encouraging, further studies are needed in order to establish safe clinical indications for Portland cement combined with radiopacifying agents.

Influence of ultrasonic radiation on the amorphous zeolite - Portland cement system

NARCIS (Netherlands)

Jakevicius, L.; Vaiciukyniene, D.; Demcenko, A.

2012-01-01

This paper considers the investigation of influence of an amorphous synthetic zeolite with inserted $Ca^{2+}$ ions additive (ASZ) on the hydration temperature of Portland cement paste. In this investigation the sonicated Portland cement paste is compared to the non-sonicated paste; and then the

Portland-pfa cement: a comparison between intergrinding and blending

Energy Technology Data Exchange (ETDEWEB)

Monk, M

1983-09-01

Portland-pfa cements containing 20-40% (by weight) pfa have been prepared in the laboratory both by intergrinding the ashes with clinker and by blending with cement. Cement properties have been assessed according to BS 4550 and scanning electron microscopy was used to examine the effects of grinding upon the pfa particles. The work has shown that intergrinding leads to an improvement in the water-reducing properties of coarse pfas and also in their pozzolanic activity as indicated by compressive strength development at later ages. Setting times have been found to be essentially the same for blended and interground cements, both being considerably longer than for typical ordinary Portland cements. Thus the results of this investigation indicate that, provided pfa's are chemically acceptable, they can be used for Portland-pfa cement manufacture by intergrinding irrespective of their coarseness.

2012 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Central Coast

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI has collected Light Detection and Ranging (LiDAR) data of the Oregon Central Coast Study Area for the Oregon Department of Geology and Mineral Industries...

2012 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Tillamook Yamhill

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI has collected Light Detection and Ranging (LiDAR) data of the Oregon Tillamook-Yamhill Study Area for the Oregon Department of Geology and Mineral Industries...

2013 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar DEM: Clackamol

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI collected Light Detection and Ranging (LiDAR) data for the Oregon LiDAR Consortium (OLC) Clackamol 2013 study area in Clackamas and Marion County, Oregon. The...

77 FR 42367 - National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing...

Science.gov (United States)

2012-07-18

... and 63 National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing... Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing Industry and Standards of... manufacturing plants. Federal government Not affected. State/local/tribal government.... Portland cement...

2012 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Green Peter

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI collected Light Detection and Ranging (LiDAR) data of the Green Peter study area for the Oregon LiDAR Consortium (OLC) in Linn County, Oregon. The collection of...

2015 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Green Peter

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI collected Light Detection and Ranging (LiDAR) data of the Green Peter study area for the Oregon LiDAR Consortium (OLC) in Linn County, Oregon. The collection of...

Recycled materials in Portland cement concrete

Science.gov (United States)

2000-06-01

This report pertains to a comprehensive study involving the use of recycled materials in Portland cement concrete. Three different materials were studied including crushed glass (CG), street sweepings (SS), and recycled concrete (RC). Blast furnace s...

2015 City of Portland, Maine, Lidar

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — 2015 City of Portland Maine Lidar Data Acquisition and Processing Woolpert Order No. 75564 Contractor: Woolpert, Inc. This task is for a high resolution data set of...

A Hero's Welcome.

Science.gov (United States)

Moores, Samantha

1999-01-01

Tony Hopson founded and directs Self Enhancement, Inc., a nonprofit program that helps inner-city youth in Portland (Oregon) improve academically and develop talents, skills, values, and attitudes needed to become positive, contributing members of society. The program's success is based on the relationship model, continuity of services,…

Analysis of Chemical Composition of Portland Cement in Ghana: A Key to Understand the Behavior of Cement

OpenAIRE

Bediako, Mark; Amankwah, Eric Opoku

2015-01-01

The performance of Portland cement in concrete or mortar formation is very well influenced by chemical compositions among other factors. Many engineers usually have little information on the chemical compositions of cement in making decisions for the choice of commercially available Portland cement in Ghana. This work analyzed five different brands of Portland cement in Ghana, namely, Ghacem ordinary Portland cement (OPC) and Portland limestone cement (PLC), CSIR-BRRI Pozzomix, Dangote OPC, a...

75 FR 54969 - National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing...

Science.gov (United States)

2010-09-09

... Hazardous Air Pollutants From the Portland Cement Manufacturing Industry and Standards of Performance for... Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing Industry and Standards of... (NESHAP) from the Portland Cement Manufacturing Industry and to the New Source Performance Standards (NSPS...

76 FR 2860 - National Emission Standards for Hazardous Air Pollutants From the Portland Cement Manufacturing...

Science.gov (United States)

2011-01-18

... Cement Manufacturing Industry and Standards of Performance for Portland Cement Plants AGENCY... Portland Cement Manufacturing Industry Docket, Docket ID No. EPA-HQ-OAR-2002-0051, 1200 Pennsylvania Ave... Portland Cement Manufacturing Industry Docket, EPA West, Room 3334, 1301 Constitution Ave., NW., Washington...

Stabilization of marly soils with portland cement

Science.gov (United States)

Piskunov, Maksim; Karzin, Evgeny; Lukina, Valentina; Lukinov, Vitaly; Kholkin, Anatolii

2017-10-01

Stabilization of marlous soils with Portland cement will increase the service life of motor roads in areas where marl is used as a local road construction material. The result of the conducted research is the conclusion about the principal possibility of stabilization of marlous soils with Portland cement, and about the optimal percentage of the mineral part and the binding agent. When planning the experiment, a simplex-lattice plan was implemented, which makes it possible to obtain a mathematical model for changing the properties of a material in the form of polynomials of incomplete third order. Brands were determined for compressive strength according to GOST 23558-94 and variants of stabilized soils were proposed for road construction.

Solidification of ion exchange resins saturated with Na+ ions: Comparison of matrices based on Portland and blast furnace slag cement

International Nuclear Information System (INIS)

Lafond, E.; Cau dit Coumes, C.; Gauffinet, S.; Chartier, D.; Stefan, L.; Le Bescop, P.

2017-01-01

This work is devoted to the conditioning of ion exchange resins used to decontaminate radioactive effluents. Calcium silicate cements may have a good potential to encapsulate spent resins. However, certain combinations of cement and resins produce a strong expansion of the final product, possibly leading to its full disintegration. The focus is placed on the understanding of the behaviour of cationic resins in the Na + form in Portland or blast furnace slag (CEM III/C) cement pastes. During hydration of the Portland cement paste, the pore solution exhibits a decrease in its osmotic pressure, which causes a transient expansion of small magnitude of the resins. At 20 °C, this expansion takes place just after setting in a poorly consolidated material and is sufficient to induce cracks. In the CEM III/C paste, swelling of the resins also occurs, but before the end of setting, and induces limited stress in the matrix which is still plastic. - Highlights: • Solidification of cationic resins in the Na + -form is investigated. • Portland and blast furnace slag cements are compared. • Deleterious expansion is observed with Portland cement only. • Resin swelling is due to a decrease in the osmotic pressure of the pore solution. • The consolidation rate of the matrix is a key parameter to prevent damage.

76 FR 78240 - Gray Portland Cement and Clinker From Japan: Continuation of Antidumping Duty Order

Science.gov (United States)

2011-12-16

... DEPARTMENT OF COMMERCE International Trade Administration [A-588-815] Gray Portland Cement and... Department) initiated the third sunset review of the antidumping duty order on gray portland cement and... of the antidumping duty order on gray portland cement and clinker from Japan would likely lead to...

Taenia solium among Refugees in the United States

Centers for Disease Control (CDC) Podcasts

2012-04-20

Dr. Seth O’Neal, a medical epidemiologist at Oregon Health & Science University, in Portland Oregon, discusses Taenia solium among Refugees.  Created: 4/20/2012 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 4/25/2012.

Evaluation of Fish Passage Conditions for Juvenile Salmonids Using Sensor Fish at Detroit Dam, Oregon

International Nuclear Information System (INIS)

Duncan, Joanne P.

2010-01-01

Fish passage conditions through two spillways at Detroit Dam on the North Santiam River in Oregon were evaluated by Pacific Northwest National Laboratory for the U.S. Army Corps of Engineers (USACE), Portland District, using Sensor Fish devices. The objective of the study was to describe and compare passage exposure conditions through Spillbay 3 and Spillbay 6 at 1.5- and 3.5-ft gate openings, identifying potential fish injury regions of the routes. The study was performed in July 2009, concurrent with HI-Z balloon-tag studies by Normandeau Associates, Inc. Sensor Fish and live fish were deployed at elevations approximately 3 ft above structure at depths determined using a computational fluid dynamics model. Data collected were analyzed to estimate (1) exposure conditions, particularly exposure to severe collision and shear events by passage route sub-regions; (2) differences in passage conditions between passage routes; and (3) relationships to live-fish injury and mortality data estimates.

Rheological Properties of Very High-Strength Portland Cement Pastes: Influence of Very Effective Superplasticizers

Directory of Open Access Journals (Sweden)

Adriano Papo

2010-01-01

Full Text Available The influence of the addition of very effective superplasticizers, that are commercially available, employed for maximising the solid loading of very high-strength Portland cement pastes, has been investigated. Cement pastes were prepared from deionized water and a commercially manufactured Portland cement (Ultracem 52.5 R. Cement and water were mixed with a vane stirrer according to ASTM Standard C305. The 0.38 to 0.44 water/cement ratio range was investigated. Three commercial superplasticizing agents produced by Ruredil S.p.a. were used. They are based on a melamine resin (Fluiment 33 M, on a modified lignosulphonate (Concretan 200 L, and on a modified polyacrylate (Ergomix 1000. Rheological tests were performed at 25°C by using the rate controlled coaxial cylinder viscometer Rotovisko-Haake 20, system M5-osc., measuring device MV2P with serrated surfaces. The tests were carried out under continuous flow conditions. The results of this study were compared with those obtained in a previous article for an ordinary Portland cement paste.

Sources and characteristics of organic matter in the Clackamas River, Oregon, related to the formation of disinfection by-products in treated drinking water

Science.gov (United States)

Carpenter, Kurt D.; Kraus, Tamara E.C.; Goldman, Jami H.; Saraceno, John Franco; Downing, Bryan D.; Bergamaschi, Brian A.; McGhee, Gordon; Triplett, Tracy

2013-01-01

This study characterized the amount and quality of organic matter in the Clackamas River, Oregon, to gain an understanding of sources that contribute to the formation of chlorinated and brominated disinfection by-products (DBPs), focusing on regulated DBPs in treated drinking water from two direct-filtration treatment plants that together serve approximately 100,000 customers. The central hypothesis guiding this study was that natural organic matter leaching out of the forested watershed, in-stream growth of benthic algae, and phytoplankton blooms in the reservoirs contribute different and varying proportions of organic carbon to the river. Differences in the amount and composition of carbon derived from each source affects the types and concentrations of DBP precursors entering the treatment plants and, as a result, yield varying DBP concentrations and species in finished water. The two classes of DBPs analyzed in this study-trihalomethanes (THMs) and haloacetic acids (HAAs)-form from precursors within the dissolved and particulate pools of organic matter present in source water. The five principal objectives of the study were to (1) describe the seasonal quantity and character of organic matter in the Clackamas River; (2) relate the amount and composition of organic matter to the formation of DBPs; (3) evaluate sources of DBP precursors in the watershed; (4) assess the use of optical measurements, including in-situ fluorescence, for estimating dissolved organic carbon (DOC) concentrations and DBP formation; and (5) assess the removal of DBP precursors during treatment by conducting treatability "jar-test" experiments at one of the treatment plants. Data collection consisted of (1) monthly sampling of source and finished water at two drinking-water treatment plants; (2) event-based sampling in the mainstem, tributaries, and North Fork Reservoir; and (3) in-situ continuous monitoring of fluorescent dissolved organic matter (FDOM), turbidity, chlorophyll-a, and

Teenage Suicide in Oregon 1983-1985.

Science.gov (United States)

Oregon State Dept. of Human Resources, Portland.

During the 3-year period from 1983 through 1985, 80 Oregon teenagers intentionally took their own lives, making suicide second only to accidents as the leading cause of death among Oregon teenagers. Data on suicides committed by individuals between the ages of 10 and 19 were retrieved from death certificates on file with the Oregon Health Division…

Effect of mineral trioxide aggregates and Portland cements on inflammatory cells.

Science.gov (United States)

Shahi, Shahriar; Rahimi, Saeed; Yavari, Hamid Reza; Mokhtari, Hadi; Roshangar, Leila; Abasi, Mehran Mesgary; Sattari, Sahar; Abdolrahimi, Majid

2010-05-01

Recently, some studies have compared mineral trioxide aggregate (MTA) with Portland cements, concluding that the principal ingredients of Portland cements are similar to those of MTA. The purpose of the present study was to evaluate the effect of gray MTA, white MTA, and gray and white Portland cements on inflammatory cells in rats. Fresh mixtures mixed with distilled water were placed in polyethylene tubes, which were implanted in the dorsal subcutaneous connective tissue of 60 Sprague-Dawley rats along with empty tubes as controls. Tissue specimens were collected after the rats were sacrificed after 7, 15, 30, 60, and 90 days. The specimens were fixed, stained, processed, and histologically evaluated under a light microscope. Inflammatory reactions were classified as grade 0: without inflammatory cells, grade I: sporadic infiltration of inflammatory cells, grade II: moderate infiltration (125 cells). Data were analyzed with the nonparametric (two factor) analysis of variance and Kruskal-Wallis H-test. All the groups showed grade III inflammation after 7 and 15 days; there was a decrease in the inflammatory process after 30, 60, and 90 days. After 90 days, gray MTA, white MTA, and control groups had grade 0 inflammatory process, but gray Portland cement and white Portland cement groups showed grade 0 to grade I inflammatory processes. MTAs were more biocompatible; however, more studies are required. Copyright (c) 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

1970 Oregon timber harvest.

Science.gov (United States)

Brian R. Wall

1971-01-01

The 1970 Oregon timber harvest of 7.98 billion board feet was the lowest recorded since the recession year of 1961 when 7.41 billion board feet of timber was produced. The 1970 log production figure was 12.8 percent below the 1969 harvest, the second consecutive year of declining production in Oregon.

Synthesis of Portland cement and calcium sulfoaluminate-belite cement for sustainable development and performance

Science.gov (United States)

Chen, Irvin Allen

Portland cement concrete, the most widely used manufactured material in the world, is made primarily from water, mineral aggregates, and portland cement. The production of portland cement is energy intensive, accounting for 2% of primary energy consumption and 5% of industrial energy consumption globally. Moreover, portland cement manufacturing contributes significantly to greenhouse gases and accounts for 5% of the global CO2 emissions resulting from human activity. The primary objective of this research was to explore methods of reducing the environmental impact of cement production while maintaining or improving current performance standards. Two approaches were taken, (1) incorporation of waste materials in portland cement synthesis, and (2) optimization of an alternative environmental friendly binder, calcium sulfoaluminate-belite cement. These approaches can lead to less energy consumption, less emission of CO2, and more reuse of industrial waste materials for cement manufacturing. In the portland cement part of the research, portland cement clinkers conforming to the compositional specifications in ASTM C 150 for Type I cement were successfully synthesized from reagent-grade chemicals with 0% to 40% fly ash and 0% to 60% slag incorporation (with 10% intervals), 72.5% limestone with 27.5% fly ash, and 65% limestone with 35% slag. The synthesized portland cements had similar early-age hydration behavior to commercial portland cement. However, waste materials significantly affected cement phase formation. The C3S--C2S ratio decreased with increasing amounts of waste materials incorporated. These differences could have implications on proportioning of raw materials for cement production when using waste materials. In the calcium sulfoaluminate-belite cement part of the research, three calcium sulfoaluminate-belite cement clinkers with a range of phase compositions were successfully synthesized from reagent-grade chemicals. The synthesized calcium sulfoaluminate

Immobilization of organic liquid wastes

International Nuclear Information System (INIS)

Greenhalgh, W.O.

1985-01-01

This report describes a portland cement immobilization process for the disposal treatment of radioactive organic liquid wastes which would be generated in a a FFTF fuels reprocessing line. An incineration system already on-hand was determined to be too costly to operate for the 100 to 400 gallons per year organic liquid. Organic test liquids were dispersed into an aqueous phosphate liquid using an emulsifier. A total of 109 gallons of potential and radioactive aqueous immiscible organic liquid wastes from Hanford 300 Area operations were solidified with portland cement and disposed of as solid waste during a 3-month test program with in-drum mixers. Waste packing efficiencies varied from 32 to 40% and included pump oils, mineral spirits, and TBP-NPH type solvents

Solidification of ion exchange resins saturated with Na{sup +} ions: Comparison of matrices based on Portland and blast furnace slag cement

Energy Technology Data Exchange (ETDEWEB)

Lafond, E. [CEA, DEN, DTCD, SPDE, F-30207 Bagnols-sur-Cèze cedex (France); Cau dit Coumes, C., E-mail: celine.cau-dit-coumes@cea.fr [CEA, DEN, DTCD, SPDE, F-30207 Bagnols-sur-Cèze cedex (France); Gauffinet, S. [Laboratoire Interdisciplinaire Carnot de Bourgogne UMR 6303 CNRS-Université de Bourgogne, Dijon, France, 9 Av Alain Savary, BP 47870, 21078 Dijon cedex (France); Chartier, D. [CEA, DEN, DTCD, SPDE, F-30207 Bagnols-sur-Cèze cedex (France); Stefan, L. [AREVA, Back End Business Group, Dismantling & Services, 1 Place Jean Millier, 92084 Paris La Défense (France); Le Bescop, P. [CEA, DEN, DPC, SECR, F-91192 Gif-sur-Yvette (France)

2017-01-15

This work is devoted to the conditioning of ion exchange resins used to decontaminate radioactive effluents. Calcium silicate cements may have a good potential to encapsulate spent resins. However, certain combinations of cement and resins produce a strong expansion of the final product, possibly leading to its full disintegration. The focus is placed on the understanding of the behaviour of cationic resins in the Na{sup +} form in Portland or blast furnace slag (CEM III/C) cement pastes. During hydration of the Portland cement paste, the pore solution exhibits a decrease in its osmotic pressure, which causes a transient expansion of small magnitude of the resins. At 20 °C, this expansion takes place just after setting in a poorly consolidated material and is sufficient to induce cracks. In the CEM III/C paste, swelling of the resins also occurs, but before the end of setting, and induces limited stress in the matrix which is still plastic. - Highlights: • Solidification of cationic resins in the Na{sup +}-form is investigated. • Portland and blast furnace slag cements are compared. • Deleterious expansion is observed with Portland cement only. • Resin swelling is due to a decrease in the osmotic pressure of the pore solution. • The consolidation rate of the matrix is a key parameter to prevent damage.

33 CFR 165.1312 - Security Zone; Portland Rose Festival on Willamette River.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Security Zone; Portland Rose Festival on Willamette River. 165.1312 Section 165.1312 Navigation and Navigable Waters COAST GUARD... § 165.1312 Security Zone; Portland Rose Festival on Willamette River. (a) Location. The following area...

The existence state of uranium(VI) in portland cement matrix material immobilization body

International Nuclear Information System (INIS)

Tan Hongbin; Li Yuxiang

2005-01-01

The basis of Portland cement material reaction with uranium, the corrosion of uranium minerals in nature and the state of study on immobilization of uranium by Portland cement matrix material are introduced, and some considerations are presented. (authors)

Freeze-Thaw Performance and Moisture-Induced Damage Resistance of Base Course Stabilized with Slow Setting Bitumen Emulsion-Portland Cement Additives

Directory of Open Access Journals (Sweden)

Mojtaba Shojaei Baghini

2015-01-01

Full Text Available Freeze-thaw (FT cycles and moisture susceptibility are important factors influencing the geotechnical characteristics of soil-aggregates. Given the lack of published information on the behavior of cement-bitumen emulsion-treated base (CBETB under environmental conditions, especially freezing and thawing, this study investigated the effects of these additives on the CBETB performance. The primary goal was to evaluate the resistance of CBETB to moisture damage by performing FT, Marshall conditioning, and AASHTO T-283 tests and to evaluate the long-term stripping susceptibility of CBETB while also predicting the liquid antistripping additives to assess the mixture’s durability and workability. Specimens were stabilized with Portland cement (0%–6%, bitumen emulsion (0%–5%, and Portland cement-bitumen emulsion mixtures and cured for 7 days, and their short- and long-term performances were studied. Evaluation results of both the Marshall stability ratio and the tensile strength ratio show that the additions of additives increase the resistance of the mixtures to moisture damage. Results of durability tests performed for determining the resistance of compacted specimens to repeated FT cycles indicate that the specimen with the 4% cement-3% bitumen emulsion mixture significantly improves water absorption, volume changes, and weight losses. This indicates the effectiveness of this additive as a road base stabilizer with excellent engineering properties for cold regions.

77 FR 27010 - Endangered and Threatened Wildlife and Plants; Revised Critical Habitat for the Northern Spotted Owl

Science.gov (United States)

2012-05-08

... Convention Center, 777 NE Martin Luther King Blvd., Portland, Oregon; 503-235-7575. Public Meetings: Public information meetings will be held at: University of Washington, Tacoma Campus, 1900 Commerce St., Jane Russell..., California 96001; 530-229-0036; Oregon Convention Center, Room C-120, 777 NE Martin Luther King Blvd...

A Community-Based Social Marketing Campaign at Pacific University Oregon: Recycling, Paper Reduction, and Environmentally Preferable Purchasing

Science.gov (United States)

Cole, Elaine J.; Fieselman, Laura

2013-01-01

Purpose: The purpose of this paper is to design a community-based social marketing (CBSM) campaign to foster sustainable behavior change in paper reduction, commingled recycling, and purchasing environmentally preferred products (EPP) with faculty and staff at Pacific University Oregon. Design/methodology/approach: A CBSM campaign was developed…

Formula of Moulding Sand, Bentonite and Portland Cement toImprove The Quality of Al-Si Cast Alloy

OpenAIRE

Andoko Andoko; Poppy Puspitasari; Avita Ayu Permanasari; Didin Zakaria Lubis

2017-01-01

A binder is any material used to strengthen the bonding of moulding sand grains. The primary function of the binder is to hold the moulding sand and other materialstogether to produce high-quality casts. In this study, there were four binder compositions being tested, i.e. 5% bentonite + 5% Portland cement, 4% bentonite + 6% Portland cement, 6% bentonite + 4% Portland cement, and 7% bentonite + 3% Portland cement. Each specimen was measured for its compressive strength, shear strength, tensil...

77 FR 56251 - Culturally Significant Objects Imported for Exhibition Determinations: “The Body Beautiful in...

Science.gov (United States)

2012-09-12

... exhibition ``The Body Beautiful in Ancient Greece,'' imported from abroad for temporary exhibition within the... at the Portland Art Museum, Portland, Oregon, from on or about October 6, 2012, until on or about January 6, 2013, the Dallas Museum of Art, Dallas, Texas, from on or about May 5, 2013, until on or about...

Utilization of Iron Ore Tailings as Raw Material for Portland Cement Clinker Production

Directory of Open Access Journals (Sweden)

Li Luo

2016-01-01

Full Text Available The cement industry has for some time been seeking alternative raw material for the Portland cement clinker production. The aim of this research was to investigate the possibility of utilizing iron ore tailings (IOT to replace clay as alumina-silicate raw material for the production of Portland cement clinker. For this purpose, two kinds of clinkers were prepared: one was prepared by IOT; the other was prepared by clay as a reference. The reactivity and burnability of raw meal, mineralogical composition and physical properties of clinker, and hydration characteristic of cement were studied by burnability analysis, differential thermal analysis, X-ray diffraction, and hydration analysis. The results showed that the raw meal containing IOT had higher reactivity and burnability than the raw meal containing clay, and the use of IOT did not affect the formation of characteristic mineralogical phases of Portland cement clinker. Furthermore, the physical and mechanical performance of two cement clinkers were similar. In addition, the use of IOT was found to improve the grindability of clinker and lower the hydration heat of Portland cement. These findings suggest that IOT can replace the clay as alumina-silicate raw material for the preparation of Portland cement clinker.

Oregon Low-Temperature-Resource Assessment Program. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Priest, G.R.; Black, G.L.; Woller, N.M.

1981-01-01

Numerous low-temperature hydrothermal systems are available for exploitation throughout the Cascades and eastern Oregon. All of these areas have heat flow significantly higher than crustal averages and many thermal aquifers. In northeastern Oregon, low temperature geothermal resources are controlled by regional stratigraphic aquifers of the Columbia River Basalt Group at shallow depths and possibly by faults at greater depths. In southeastern Oregon most hydrothermal systems are of higher temperature than those of northeastern Oregon and are controlled by high-angle fault zones and layered volcanic aquifers. The Cascades have very high heat flow but few large population centers. Direct use potential in the Cascades is therefore limited, except possibly in the cities of Oakridge and Ashland, where load may be great enough to stimulate development. Absence of large population centers also inhibits initial low temperature geothermal development in eastern Oregon. It may be that uses for the abundant low temperature geothermal resources of the state will have to be found which do not require large nearby population centers. One promising use is generation of electricity from freon-based biphase electrical generators. These generators will be installed on wells at Vale and Lakeview in the summer of 1982 to evaluate their potential use on geothermal waters with temperatures as low as 80/sup 0/C (176/sup 0/F).

Modelling porewater chemistry in hydrated Portland cement

International Nuclear Information System (INIS)

Berner, U.R.

1987-01-01

Extensive employment of concrete is foreseen in radioactive waste repositories. A prerequisite for modelling the interactions between concrete and formation waters is characterization of the concrete system. Available experimental data from high pressure squeezing of cement pore-water indicate that, besides the high pH due to alkali hydroxide dissolution, cement composition itself influences the solubility determining solid phases. A model which simulates the hydration of Portland cement assuming complete hydration of the main clinker minerals is presented. The model also includes parameters describing the reactions between the cement and blending agents. Comparison with measured pore-water data generally gives a consistent picture and, as expected, the model gives correct predictions for pure Portland cements. For blended cements, the required additional parameters can, to some extent, be derived from pore-water analysis. 14 references, 1 figure, 4 tables

The immobilization of organic liquid wastes

International Nuclear Information System (INIS)

Greenhalgh, W.O.

1986-01-01

This report describes a portland cement immobilization process for the disposal treatment of radioactive organic liquid wastes which would be generated in a FFTF fuels reprocessing line. An incineration system already on-hand was determined to be too costly to operate for the 100 to 400 gallons per year organic liquid. Organic test liquids were dispersed into an aqueous phosphate liquid using an emulsifier. A total of 109 gallons of potential and radioactive aqueous immiscible organic liquid wastes from Hanford 300 Area operations were solidified with portland cement and disposed of as solid waste during a 3 month test program with in-drum mixers. Waste packing efficiencies varied from 32 to 40% and included pump oils, mineral spirits, and TBP-NPH type solvents

Laboratory-based educational and outreach activities in the framework of a CAREER award at the University of Oregon

Science.gov (United States)

Bindeman, I. N.

2011-12-01

The Stable Isotope Laboratory at the University of Oregon has been used as a learning and outreach center in the framework of the 09 award entitled "Stable isotope insights into large-volume volcanic eruptions". The PI and other members of the group have actively recruitted undergraduate students, summer session and catalytic outreach undergraduates, and hosted international students, visitors, and collaborators from Russia, Iceland, France, the UK, Australia, and Switzerland. We also integrated closely with the Oregon-wide summer program that brings community college students to the University of Oregon for 2.5 months summer research residence (UCORE). In total we gave supervised five undergraduate students and three UCORE students. Additionally, we recruited undergraduates from U of Chicago, Colorado and Pomona Colleges to spend summers in the lab and in the field. In conjunction with the NSF funded PIRE program, two female graduate and one female undergraduate students participated in fieldwork in Kamchatka, and three Kamchatka undergraduates, and one Moscow graduate student visited the University Oregon. Students performed their own projects or Senior Theses and reported their results locally and at AGU conferences. We developed a management structure in which graduate students, a postdoc, and lab technician co-supervised students and visitors and this exposed them into the supervisory roles, contributed to the project progress, and liberated PI from micromanagement duties. The talk will present our experience with this management concept of a lab-based-learning initiative, which defines roles for each member of the lab. Our outreach activities included public lectures at community colleges by PI and a graduate student, and the topical Penrose conference co-organized by the PI, which attracted many students and visitors who collected their data in the lab. PI has introduced a voluntary fieldtrip as a part of his Volcanoes and Earthquake large enrollment class

Evaluating Microbial Indicators of Environmental Condition in Oregon Rivers

Science.gov (United States)

Pennington, Alan T.; Harding, Anna K.; Hendricks, Charles W.; Campbell, Heidi M. K.

2001-12-01

Traditional bacterial indicators used in public health to assess water quality and the Biolog® system were evaluated to compare their response to biological, chemical, and physical habitat indicators of stream condition both within the state of Oregon and among ecoregion aggregates (Coast Range, Willamette Valley, Cascades, and eastern Oregon). Forty-three randomly selected Oregon river sites were sampled during the summer in 1997 and 1998. The public health indicators included heterotrophic plate counts (HPC), total coliforms (TC), fecal coliforms (FC) and Escherichia coli (EC). Statewide, HPC correlated strongly with physical habitat (elevation, riparian complexity, % canopy presence, and indices of agriculture, pavement, road, pasture, and total disturbance) and chemistry (pH, dissolved O2, specific conductance, acid-neutralizing capacity, dissolved organic carbon, total N, total P, SiO2, and SO4). FC and EC were significantly correlated generally with the river chemistry indicators. TC bacteria significantly correlated with riparian complexity, road disturbance, dissolved O2, and SiO2 and FC. Analyzing the sites by ecoregion, eastern Oregon was characterized by high HPC, FC, EC, nutrient loads, and indices of human disturbance, whereas the Cascades ecoregion had correspondingly low counts of these indicators. The Coast Range and Willamette Valley presented inconsistent indicator patterns that are more difficult to characterize. Attempts to distinguish between ecoregions with the Biolog system were not successful, nor did a statistical pattern emerge between the first five principle components and the other environmental indicators. Our research suggests that some traditional public health microbial indicators may be useful in measuring the environmental condition of lotic systems.

Effects of cement particle size distribution on performance properties of Portland cement-based materials

Energy Technology Data Exchange (ETDEWEB)

Bentz, D.P.; Garboczi, E.J.; Haecker, C.J.; Jensen, O.M.

1999-10-01

The original size, spatial distribution, and composition of Portland cement particles have a large influence on hydration kinetics, microstructure development, and ultimate properties of cement-based materials. In this paper, the effects of cement particle size distribution on a variety of performance properties are explored via computer simulation and a few experimental studies. Properties examined include setting time, heat release, capillary porosity percolation, diffusivity, chemical shrinkage, autogenous shrinkage, internal relative humidity evolution, and interfacial transition zone microstructure. The effects of flocculation and dispersion of the cement particles in the starting microstructures on resultant properties are also briefly evaluated. The computer simulations are conducted using two cement particle size distributions that bound those commonly in use today and three different water-to-cement ratios: 0.5, 0.3, and 0.246. For lower water-to-cement ratio systems, the use of coarser cements may offer equivalent or superior performance, as well as reducing production costs for the manufacturer.

Partial replacement of Portland cement by red ceramic waste in mortars: study of pozzolanic activity; Substituicao parcial do cimento Portland por residuo de ceramica vermelha em argamassas: estudo da atividade pozolonica

Energy Technology Data Exchange (ETDEWEB)

Silva, A.R. da; Cabral, K.C.; Pinto, E.N. de M.G.l., E-mail: kleber.cabral@ufersa.edu.br [Universidade Federal Rural do Semi-Arido (UFERSA), Mossoro, RN (Brazil)

2016-07-01

The objective of this study is to analyze the pozzolanic activity of red ceramic residue on the partial replacement of Portland cement in mortars. The mortars were prepared by substituting 25% of the Portland cement for ground of ceramic residue with water cement’s factor of 0.48. The concrete used to construct the reference mortars and those with addiction was CPII-Z-32 (compound of Portland pozzolana cement). The chemical analysis and physical ceramic waste showed that this meets the requirements of NBR12653 (2014) for use as pozzolanic material. The pozzolanic activity index (IAP) obtained for the ceramic waste to twenty-eight days cure rate was 80.28%. (author)

2012 OLC Lidar: West Metro, Oregon

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI has collected Light Detection and Ranging (LiDAR) data of the Oregon West Metro Study Area for the Oregon Department of Geology and Mineral Industries (DOGAMI)....

Green ethic takes root: how a US city is changing its ways

Energy Technology Data Exchange (ETDEWEB)

Cohn, L.

2005-10-01

The green power utility programme, sustainable architecture and public attitudes in the city of Portland in the northwest US state have made it one of North America's greenest cities. Portland has adopted a goal of purchasing all the electricity to supply municipal facilities from renewable resources by 2010 and the city has nearly 30,000 residential customers buying green power. Portland has a number of community gathering places such as community bulletin boards powered by solar energy and an increasing number of building projects registered with the US Green Building Council as LEEd (Leadership in Energy and Environmental Design) buildings. A number of organisations that support sustainable projects are based in Portland, including Portland's own Office of Sustainable Development (one of the first of its kind in the USA), Renewable Northwest Project (RNP), Bonneville Energy Foundation (BEF) and City Repair. RNP promotes the use of renewable energy while BEF and City Repair offer creative ideas to put renewable energy into practice. Incentives to fuel the growth of solar energy in Oregon are examined in a side box.

Outcome prediction in home- and community-based brain injury rehabilitation using the Mayo-Portland Adaptability Inventory.

Science.gov (United States)

Malec, James F; Parrot, Devan; Altman, Irwin M; Swick, Shannon

2015-01-01

The objective of the study was to develop statistical formulas to predict levels of community participation on discharge from post-hospital brain injury rehabilitation using retrospective data analysis. Data were collected from seven geographically distinct programmes in a home- and community-based brain injury rehabilitation provider network. Participants were 642 individuals with post-traumatic brain injury. Interventions consisted of home- and community-based brain injury rehabilitation. The main outcome measure was the Mayo-Portland Adaptability Inventory (MPAI-4) Participation Index. Linear discriminant models using admission MPAI-4 Participation Index score and log chronicity correctly predicted excellent (no to minimal participation limitations), very good (very mild participation limitations), good (mild participation limitations), and limited (significant participation limitations) outcome levels at discharge. Predicting broad outcome categories for post-hospital rehabilitation programmes based on admission assessment data appears feasible and valid. Equations to provide patients and families with probability statements on admission about expected levels of outcome are provided. It is unknown to what degree these prediction equations can be reliably applied and valid in other settings.

State of Oregon 4th biennial energy plan

International Nuclear Information System (INIS)

Anon.

1991-01-01

State law directs the Oregon Department of Energy (ODOE) to prepare an energy plan every two years. This is the Fourth Biennial Energy Plan. The Plan is a policy blueprint for how to best meet Oregon's future energy needs. It identifies the key energy issues facing the state and sets forth policies and actions to achieve our energy goals of reliable, least-cost, and environmentally safe supply. This book presents: Oregon's demand and supply picture today. The progress Oregon has made toward energy efficiency. Oregon's energy demand and supply outlook for the next 20 years. Estimates of cost-effective conservation and other resources that could contribute to the state's energy supply. The major energy-related health, safety, and environmental issues facing the state. A strategy to reduce greenhouse gas emissions 20 percent from 1988 levels by 2005. A two-year Action Plant that spells out ODOE's recommended actions for achieving Oregon's energy goals

Recycling of porcelain tile polishing residue in portland cement: hydration efficiency.

Science.gov (United States)

Pelisser, Fernando; Steiner, Luiz Renato; Bernardin, Adriano Michael

2012-02-21

Ceramic tiles are widely used by the construction industry, and the manufacturing process of ceramic tiles generates as a major residue mud derived from the polishing step. This residue is too impure to be reused in the ceramic process and is usually discarded as waste in landfills. But the analysis of the particle size and concentration of silica of this residue shows a potential use in the manufacture of building materials based on portland cement. Tests were conducted on cement pastes and mortars using the addition of 10% and 20% (mass) of the residue. The results of compressive strength in mortars made up to 56 days showed a significant increase in compressive strength greater than 50%. The result of thermogravimetry shows that portlandite is consumed by the cement formed by the silica present in the residue in order to form calcium silicate hydrate and featuring a pozzolanic reaction. This effect improves the performance of cement, contributes to research and application of supplementary cementitious materials, and optimizes the use of portland cement, reducing the environmental impacts of carbon dioxide emissions from its production.

Cell attachment properties of Portland cement-based endodontic materials: biological and methodological considerations.

Science.gov (United States)

Ahmed, Hany Mohamed Aly; Luddin, Norhayati; Kannan, Thirumulu Ponnuraj; Mokhtar, Khairani Idah; Ahmad, Azlina

2014-10-01

The attachment and spreading of mammalian cells on endodontic biomaterials are an area of active research. The purpose of this review is to discuss the cell attachment properties of Portland cement (PC)-based materials by using scanning electron microscope (SEM). In addition, methodological aspects and technical challenges are discussed. A PubMed electronic search was conducted by using appropriate key words to identify the available investigations on the cell attachment properties of PC-based endodontic materials. After retrieving the full text of related articles, the cross citations were also identified. A total of 23 articles published between January 1993 and October 2013 were identified. This review summarizes the cell attachment properties of commercial and experimental PC-based materials on different cell cultures by using SEM. Methodological procedures, technical challenges, and relevance of SEM in determining the biological profile of PC-based materials are discussed. SEM observations demonstrate that commercial MTA formulations show favorable cell attachment properties, which is consistent with their successful clinical outcomes. The favorable cell attachment properties of PC and its modified formulations support its potential use as a substitute for mineral trioxide aggregate. However, researchers should carefully select cell types for their SEM investigations that would be in contact with the proposed PC-based combinations in the clinical situation. Despite being a technical challenge, SEM provides useful information on the cell attachment properties of PC-based materials; however, other assays for cell proliferation and viability are essential to come up with an accurate in vitro biological profile of any given PC-based formulation. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Field-trip guide to Columbia River flood basalts, associated rhyolites, and diverse post-plume volcanism in eastern Oregon

Science.gov (United States)

Ferns, Mark L.; Streck, Martin J.; McClaughry, Jason D.

2017-08-09

The Miocene Columbia River Basalt Group (CRBG) is the youngest and best preserved continental flood basalt province on Earth, linked in space and time with a compositionally diverse succession of volcanic rocks that partially record the apparent emergence and passage of the Yellowstone plume head through eastern Oregon during the late Cenozoic. This compositionally diverse suite of volcanic rocks are considered part of the La Grande-Owyhee eruptive axis (LOEA), an approximately 300-kilometer-long (185 mile), north-northwest-trending, middle Miocene to Pliocene volcanic belt located along the eastern margin of the Columbia River flood basalt province. Volcanic rocks erupted from and preserved within the LOEA form an important regional stratigraphic link between the (1) flood basalt-dominated Columbia Plateau on the north, (2) bimodal basalt-rhyolite vent complexes of the Owyhee Plateau on the south, (3) bimodal basalt-rhyolite and time-transgressive rhyolitic volcanic fields of the Snake River Plain-Yellowstone Plateau, and (4) the High Lava Plains of central Oregon.This field-trip guide describes a 4-day geologic excursion that will explore the stratigraphic and geochemical relationships among mafic rocks of the Columbia River Basalt Group and coeval and compositionally diverse volcanic rocks associated with the early “Yellowstone track” and High Lava Plains in eastern Oregon. Beginning in Portland, the Day 1 log traverses the Columbia River gorge eastward to Baker City, focusing on prominent outcrops that reveal a distal succession of laterally extensive, large-volume tholeiitic flood lavas of the Grande Ronde, Wanapum, and Saddle Mountains Basalt formations of the CRBG. These “great flows” are typical of the well-studied flood basalt-dominated Columbia Plateau, where interbedded silicic and calc-alkaline lavas are conspicuously absent. The latter part of Day 1 will highlight exposures of middle to late Miocene silicic ash-flow tuffs, rhyolite domes, and

76 FR 54206 - Gray Portland Cement and Clinker From Japan: Final Results of the Expedited Third Sunset Review...

Science.gov (United States)

2011-08-31

... DEPARTMENT OF COMMERCE International Trade Administration [A-588-815] Gray Portland Cement and... portland cement and clinker from Japan. As a result of this third sunset review, the Department finds that... initiation of the third sunset review of the antidumping duty order on gray portland cement and clinker from...

Chemical composition, radiopacity, and biocompatibility of Portland cement with bismuth oxide.

Science.gov (United States)

Hwang, Yun-Chan; Lee, Song-Hee; Hwang, In-Nam; Kang, In-Chol; Kim, Min-Seok; Kim, Sun-Hun; Son, Ho-Hyun; Oh, Won-Mann

2009-03-01

This study compared the chemical constitution, radiopacity, and biocompatibility of Portland cement containing bismuth oxide (experimental cement) with those of Portland cement and mineral trioxide aggregate (MTA). The chemical constitution of materials was determined by scanning electron microscopy and energy-dispersive X-ray analysis. The radiopacity of the materials was determined using the ISO/6876 method. The biocompatibility of the materials was tested by MTT assay and tissue reaction. The constitution of all materials was similar. However, the Portland cement and experimental cement were more irregular and had a larger particle size than MTA. The radiopacity of the experimental cement was similar to MTA. The MTT assay revealed MTA to have slightly higher cell viability than the other materials. However, there were no statistically significant differences between the materials, with the exception of MTA at 24 h. There was no significant difference in the tissue reaction between the experimental groups. These results suggest that the experimental cement may be used as a substitute for MTA.

The Estimation of Compaction Parameter Values Based on Soil Properties Values Stabilized with Portland Cement

Science.gov (United States)

Lubis, A. S.; Muis, Z. A.; Pasaribu, M. I.

2017-03-01

The strength and durability of pavement construction is highly dependent on the properties and subgrade bearing capacity. This then led to the idea of the selection methods to estimate the density of the soil with the proper implementation of the system, fast and economical. This study aims to estimate the compaction parameter value namely the maximum dry unit weight (γd max) and optimum moisture content (wopt) of the soil properties value that stabilized with Portland Cement. Tests conducted in the laboratory of soil mechanics to determine the index properties (fines and liquid limit) and Standard Compaction Test. Soil samples that have Plasticity Index (PI) between 0-15% then mixed with Portland Cement (PC) with variations of 2%, 4%, 6%, 8% and 10%, each 10 samples. The results showed that the maximum dry unit weight (γd max) and wopt has a significant relationship with percent fines, liquid limit and the percentation of cement. Equation for the estimated maximum dry unit weight (γd max) = 1.782 - 0.011*LL + 0,000*F + 0.006*PS with R2 = 0.915 and the estimated optimum moisture content (wopt) = 3.441 + 0.594*LL + 0,025*F + 0,024*PS with R2 = 0.726.

Optimization of calcium chloride content on bioactivity and mechanical properties of white Portland cement

International Nuclear Information System (INIS)

Torkittikul, Pincha; Chaipanich, Arnon

2012-01-01

This research investigates the optimization of calcium chloride content on the bioactivity and mechanical properties of white Portland cement. Calcium chloride was used as an addition of White Portland cement at 0, 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10% by weight. Calcium chloride was dissolved in sterile distilled water and blended with White Portland cement using a water to cement ratio of 0.5. Analysis of the bioactivity and pH of white Portland cement pastes with calcium chloride added at various amounts was carried out in simulated body fluid. Setting time, density, compressive strength and volume of permeable voids were also investigated. The characteristics of cement pastes were examined by X-ray diffractometer and scanning electron microscope linked to an energy-dispersive X-ray analyzer. The result indicated that the addition of calcium chloride could accelerate the hydration of white Portland cement, resulting in a decrease in setting time and an increase in early strength of the pastes. The compressive strength of all cement pastes with added calcium chloride was higher than that of the pure cement paste, and the addition of calcium chloride at 8 wt.% led to achieving the highest strength. Furthermore, white Portland cement pastes both with and without calcium chloride showed well-established bioactivity with respect to the formation of a hydroxyapatite layer on the material within 7 days following immersion in simulated body fluid; white Portland cement paste with added 3%CaCl 2 exhibited the best bioactivity. - Highlights: ► Optimization CaCl 2 content on the bioactivity and mechanical properties. ► CaCl 2 was used as an addition at 0, 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10% by weight. ► CaCl 2 resulted in a decrease in setting time and an increase in early strength. ► Addition of 3%CaCl 2 exhibited the optimum formation of hydroxyapatite.

Contribución al estudio de los reacciones de hidratación del cemento portland por espectroscopia infrarroja II. Estudio de clínkeres y de cementos portland anhidros

Directory of Open Access Journals (Sweden)

Vázquez-Moreno, Tomás

1976-06-01

Full Text Available Not availableEn un artículo anterior (1 se dio cuenta de los trabajos realizados sobre la aplicación de la espectroscopia IR al estudio de las principales fases sintetizadas del clínker de cemento portland como fase previa al estudio de diversos clínkeres, obtenidos por nosotros en el laboratorio a partir de crudos industriales, y de distintos cementos portland comerciales anhidros.

Stabilization of chromium salt in ordinary portland cement

Indian Academy of Sciences (India)

Ordinary Portland cement (OPC) samples containing the chromium salt have been investigated using differential microcalorimetry, conductometry and Fourier transform infrared spectroscopic analysis. The effect of chromium on OPC hydration was evaluated by continuous observing of early hydration.

Evaluation of the strength and radiopacity of Portland cement with varying additions of bismuth oxide.

Science.gov (United States)

Saliba, E; Abbassi-Ghadi, S; Vowles, R; Camilleri, J; Hooper, S; Camilleri, J

2009-04-01

To study the effect of addition of various proportions of bismuth oxide on compressive strength and radiopacity of Portland cement. The compressive strength of white Portland cement and cement replaced with 10, 15, 20, 25 and 30% bismuth oxide was evaluated by testing cylinders 6 mm in diameter and 12 mm high. Twelve cylinders were tested for each material under study. The radiopacity of the cements tested was evaluated using an aluminium step-wedge and densitometer. The optical density was compared with the relevant thickness of aluminium (Al). Statistical analysis was performed using Analysis of Variance (ANOVA) with P = 0.05 and Tukey test to perform multiple comparison tests. Various additions of bismuth oxide had no significant effect on the strength of the material when compared with the unmodified Portland cement (P > 0.05). The radiopacity of the cements tested ranged from 2.02 mm Al for Portland cement to 9.79 mm Al for the highest bismuth replacement. Addition of bismuth oxide did not affect the compressive strength of Portland cement. All the bismuth oxide cement mixtures had radio-opacities higher than 3 mm thickness of aluminium.

Propriedades mecânicas de materiais compósitos à base de cimento Portland e resina epoxi Mechanical properties of composite materials based on portland cement and epoxy resin

Directory of Open Access Journals (Sweden)

T. H. Panzera

2010-03-01

Full Text Available O estudo de materiais de alto desempenho e multifuncionais, como os compósitos poliméricos cimentícios, tem sido o foco de inúmeras pesquisas na indústria da construção civil. Este trabalho investiga o efeito da combinação de uma fase polimérica termorrígida, uma resina epóxi, com cimento Portland branco estrutural, seguido da avaliação da resistência à compressão e módulo de elasticidade. Este compósito, quando comparado individualmente com as suas matérias-prima originais, promove um aumento da resistência mecânica à compressão, redução da massa específica e, também uma mudança significativa do comportamento mecânico. As mudanças nas propriedades mecânicas estão associadas à hidratação da fase cimentícia na presença da resina, fato comprovado através da análise espectroscópica na região do infravermelho.The study of multi-functional materials of high performance, as the polymeric-cementitious composites, has been the focus of several researches in the industry of the civil engineering. This work investigates the effect of the combination of a thermorigid epoxy phase and the white Portland cement, followed by the evaluation of its compressive strength and modulus of elasticity. This composite, when the phases are individually compared, provides an increase of the compressive strength, a reduction of the density, and a significant change of the mechanical behaviour. The changes in mechanical behaviour are associated with the hydration of cement in the presence of resin, which was evident after infrared spectroscopy analysis.

EnviroAtlas - Portland, ME - Ecosystem Services by Block Group

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset presents environmental benefits of the urban forest in 146 block groups in Portland, Maine. Carbon attributes, temperature reduction,...

Silica fume effect on retention characteristics of portland cement for uranium (VI)

International Nuclear Information System (INIS)

Tan Hongbin; Ma Xiaoling; Li Yuxiang

2005-01-01

With simulated groundwater as leachant, the retention capabilities of the portland cement, which contains different amount of silica fume, are investigated under 25 degree C and 42 days. The results indicate that silica fume can improve the retention capabilities of portland cement for uranium. When the cement contains 15% silica fume, the diffusion coefficient is 7 x 10 -3 cm 3 · -1 . It is only 5.5% of the cement without containing fume. (authors)

Analysis of metal contents in Portland Type V and MTA-based cements.

Science.gov (United States)

Dorileo, Maura Cristiane Gonçales Orçati; Bandeca, Matheus Coelho; Pedro, Fábio Luis Miranda; Volpato, Luiz Evaristo Ricci; Guedes, Orlando Aguirre; Dalla Villa, Ricardo; Tonetto, Mateus Rodrigues; Borges, Alvaro Henrique

2014-01-01

The aim of this study was to determine, by Atomic Absorption Spectrometry (AAS), the concentration levels of 11 metals in Type V gray and structural white PC, ProRoot MTA, and MTA Bio. Samples, containing one gram of each tested cement, were prepared and transferred to a 100 mL Teflon tube with a mixture of 7.0 mL of nitric acid and 21 mL of hydrochloric acid. After the reaction, the mixture was filtered and then volumed to 50 mL of distilled water. For each metal, specific patterns were determined from universal standards. Arsenic quantification was performed by hydride generator. The analysis was performed five times and the data were statistically analyzed at 5% level of significance. Only the cadmium presented concentration levels of values lower than the quantification limit of the device. The AAS analysis showed increased levels of calcium, nickel, and zinc in structural white PC. Type V PC presented the greatest concentration levels of arsenic, chromium, copper, iron, lead, and manganese (P cements, and the lowest concentration levels were observed in Portland cements, while the highest were observed in ProRoot MTA. Both PC and MTA-based cements showed evidence of metals inclusion.

Sealing ability of mineral trioxide aggregate and Portland cement for furcal perforation repair: a protein leakage study.

Science.gov (United States)

Shahi, Shahriar; Rahimi, Saeed; Hasan, Maryam; Shiezadeh, Vahab; Abdolrahimi, Majid

2009-12-01

The purpose of this study was to compare the sealing ability of gray mineral trioxide aggregate (GMTA), white MTA (WMTA), and both white and gray Portland cement as furcation perforation repair materials. A total of 120 human mandibular first molars were used. After root canal obturation and preparation of furcal perforations the specimens were randomly divided into four groups of 25 teeth each. In groups A, B, C, and D furcation perforations were filled with WMTA, GMTA, white Portland cement, and type II Portland cement, respectively. Ten teeth were used as positive controls with no filling materials in the perforations and 10 teeth with complete coverage with two layers of nail varnish were used as negative controls. A protein leakage model utilizing 22% bovine serum albumin (BSA) was used for evaluation. Leakage was noted when color conversion of the protein reagent was observed. The controls behaved as expected. Leakage was found in the samples from group A (WMTA), group B (GMTA), and in the two other groups (white and gray Portland cement). There were no statistically significant differences between GMTA and WMTA or white and gray Portland cement, but significant differences were observed between the MTA groups and the Portland cement groups. It was concluded that Portland cements have better sealing ability than MTA, and can be recommended for repair of furcation perforation if the present results are supported by other in vivo and in vitro studies.

Mineral trioxide aggregate and Portland cement promote biomineralization in vivo.

Science.gov (United States)

Dreger, Luonothar Antunes Schmitt; Felippe, Wilson Tadeu; Reyes-Carmona, Jessie Fabiola; Felippe, Gabriela Santos; Bortoluzzi, Eduardo Antunes; Felippe, Mara Cristina Santos

2012-03-01

Mineral trioxide aggregate (MTA) and Portland cement have been shown to be bioactive because of their ability to produce biologically compatible carbonated apatite. This study analyzed the interaction of MTA and white Portland cement with dentin in vivo. Seventy-two human dentin tubes were filled with MTA Branco, MTA BIO, and white Portland cement + 20% bismuth oxide (PC1) or PC1 + 10% of calcium chloride (PC2) and implanted subcutaneously in 18 rats at 4 sites from the dorsal area. Empty dentin tubes, implanted in rats of a pilot study, were used as control. After 30, 60, and 90 days, the animals were killed, and the dentin tubes were retrieved for scanning electron microscope analysis. In the periods of 30 and 60 days, the mineral deposition in the material-dentin interface (interfacial layer) and in the interior of dentinal tubules was detected in more tubes filled with MTA Branco and MTA BIO than in tubes filled with PC1 and PC2. After 90 days, the interfacial layer and intratubular mineralization were detected in all tubes except for 3 and 1 of the tubes filled with PC2, respectively. It was concluded that all the cements tested were bioactive. The cements released some of their components in the tissue capable of stimulating mineral deposition in the cement-dentin interface and in the interior of the dentinal tubules. MTA BIO and MTA Branco were more effective in promoting the biomineralization process than Portland cements, mainly after 30 and 60 days. Copyright © 2012 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone

DEFF Research Database (Denmark)

Moesgaard, M; Poulsen, Søren Lundsted; Herfort, D

2012-01-01

M. MOESGAARD, S.L. POULSEN, D. HERFORT, M. STEENBERG, L.F. KIRKEGAARD, J. SKIBSTED, Y. YUE, Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone, Journal of the American Ceramic Society 95, 403 – 409 (2012).......M. MOESGAARD, S.L. POULSEN, D. HERFORT, M. STEENBERG, L.F. KIRKEGAARD, J. SKIBSTED, Y. YUE, Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone, Journal of the American Ceramic Society 95, 403 – 409 (2012)....

Sulfatos en el cemento portland y su incidencia sobre el falso fraguado: Estado actual del conocimiento

Directory of Open Access Journals (Sweden)

de la Cruz, Ignacio

1983-12-01

Full Text Available A bibliographical study is carried out of the sulphates which may be present in the clinker and Portland cement, as likewise the effects of the aeration and temperature on the setting. This work is a prior phase of a wide experimental investigation carried out in the IETCC, on anomalies or setting and phenomena of "lumping" in Portland cement.

Se realiza un estudio bibliográfico de los sulfatos que pueden estar presentes en el clínker y cemento portland, así como de los efectos de la aireación y temperatura sobre el fraguado. Este trabajo es la fase previa de una amplia investigación experimental realizada en el IETCC, sobre anomalías de fraguado y fenómenos de "aterronamiento" en el cemento portland.

Effect of blastfurnace slag addition to Portland cement for cationic exchange resins encapsulation

Directory of Open Access Journals (Sweden)

Stefan L.

2013-07-01

Full Text Available In the nuclear industry, cement-based materials are extensively used to encapsulate spent ion exchange resins (IERs before their final disposal in a repository. It is well known that the cement has to be carefully selected to prevent any deleterious expansion of the solidified waste form, but the reasons for this possible expansion are not clearly established. This work aims at filling the gap. The swelling pressure of IERs is first investigated as a function of ions exchange and ionic strength. It is shown that pressures of a few tenths of MPa can be produced by decreases in the ionic strength of the bulk solution, or by ion exchanges (2Na+ instead of Ca2+, Na+ instead of K+. Then, the chemical evolution of cationic resins initially in the Na+ form is characterized in CEM I (Portland cement and CEM III (Portland cement + blastfurnace slag cements at early age and an explanation is proposed for the better stability of CEM III material.

77 FR 35744 - Requested Administrative Waiver of the Coastwise Trade Laws: Vessel ORIENTAL MYSTIQUE; Invitation...

Science.gov (United States)

2012-06-14

... Portland, Oregon and Oregon, City. The theme of these cruises will be on Chinese culture and nautical... businesses in the U.S. that use U.S.-flag vessels. If MARAD determines, in accordance with 46 U.S.C. 12121... adverse effect on a U.S.-vessel builder or a business that uses U.S.-flag vessels in that business, a...

2012 OLC Lidar DEM: West Metro, Oregon

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI has collected Light Detection and Ranging (LiDAR) data of the Oregon West Metro Study Area for the Oregon Department of Geology and Mineral Industries (DOGAMI)....

Hazardous Materials Hazard Analysis, Portland, Oregon.

Science.gov (United States)

1981-06-01

poisons and flammables are found in all agriculture and garden supply shops, automotive repair facilities, retail paint and hardware stores, etc...Peroxide rompressed Gases and Welding 4 NON-FLAMMABLE GAS: Surpplies Liquid Nitrogen FLAMMABLE GAS: Acetylene Hydrogen Propane Propylene Oxide OTHER...this small community said Sunday and where the water and the chemicals and 16,000 bags of chemicals were de- that he was upset with the way officials

Ordinary Portland Cement matrix for solidification of cellulosic protective clothes hazardous wastes

International Nuclear Information System (INIS)

Shatta, H.A.; Saleh, H.M.

2006-01-01

The used cellulosic protective clothes constitutes considerable fraction of the hazardous and radioactive wastes accumulated during the practical daily life. The direct solidification of these wastes with ordinary Portland cement resulted in waste forms having undesired characters, therefore, it is recommended to immobilize the secondary waste solutions coming from the oxidative degradation of the used protective clothes waste simulates rather than direct imbedding. IR analyses, X-ray diffraction and thermal characteristics for products of both direct encapsulation of the waste and the cementation of its degradation products were performed to evaluate the properties of the final waste cemented form before their disposal. Based on the results reached from X-ray diffraction, IR spectrograms and thermal analyses reports, it could be stated that no detectable changes in hydration and curing coarse of ordinary Portland cement when mixing the residual secondary waste solution resulting from the oxidative degradation of the used protective clothes waste simulate compared with mixing cement with water and in reverse with imbedding the unprocessed waste in cement matrix

Hydration characteristics of zirconium oxide replaced Portland cement for use as a root-end filling material.

Science.gov (United States)

Camilleri, J; Cutajar, A; Mallia, B

2011-08-01

Zirconium oxide can be added to dental materials rendering them sufficiently radiopaque. It can thus be used to replace the bismuth oxide in mineral trioxide aggregate (MTA). Replacement of Portland cement with 30% zirconium oxide mixed at a water/cement ratio of 0.3 resulted in a material with adequate physical properties. This study aimed at investigating the microstructure, pH and leaching in physiological solution of Portland cement replaced zirconium oxide at either water-powder or water-cement ratios of 0.3 for use as a root-end filling material. The hydration characteristics of the materials which exhibited optimal behavior were evaluated. Portland cement replaced by zirconium oxide in varying amounts ranging from 0 to 50% in increments of 10 was prepared and divided into two sets. One set was prepared at a constant water/cement ratio while the other set at a constant water/powder ratio of 0.3. Portland cement and MTA were used as controls. The materials were analyzed under the scanning electron microscope (SEM) and the hydration products were determined. X-ray energy dispersive analysis (EDX) was used to analyze the elemental composition of the hydration products. The pH and the amount of leachate in Hank's balanced salt solution (HBSS) were evaluated. A material that had optimal properties that satisfied set criteria and could replace MTA was selected. The microstructure of the prototype material and Portland cement used as a control was assessed after 30 days using SEM and atomic ratio diagrams of Al/Ca versus Si/Ca and S/Ca versus Al/Ca were plotted. The hydration products of Portland cement replaced with 30% zirconium oxide mixed at water/cement ratio of 0.3 were calcium silicate hydrate, calcium hydroxide and minimal amounts of ettringite and monosulphate. The calcium hydroxide leached in HBSS solution resulted in an increase in the pH value. The zirconium oxide acted as inert filler and exhibited no reaction with the hydration by-products of Portland

Effect of three natural pozzolans in portland cement hydration

Directory of Open Access Journals (Sweden)

Rahhal, V.

2003-03-01

Full Text Available Natural pozzolans have been used since ancient times and continues to be used today. The chemistry and morphological composition of natural pozzolans and their particle size distribution allows classifying them as more or less reactive pozzolan. In this research several techniques have been used to study the influence of pozzolan on portland cement hydration as much as to evaluate the mechanical and durable properties of concretes, mortars and pastes containing pozzolans. This paper describes the effect of incorporating three natural pozzolans to two cements with very different mineralogical composition. The techniques used were: conduction calorimetry and Fratini test. Results proved that pozzolanic activity and the acceleration and retardation of hydration reaction depend on the mineralogical composition of the portland cernent used. Effects of dilution, stimulation, acceleration or retardation reactions, behavior into areas of heat dissipation and pozzolanic activity depend on the percentage of pozzolan used and the age in which it has been analyzed.

El uso de las puzolanas naturales se remonta a la antigüedad, no obstante, actualmente continúa su utilización. La composición química y morfológica de las puzolanas naturales, sumado al tamaño de sus partículas, las califican como más o menos reactivas. En el estudio de las mismas, se han aplicado variadas técnicas para el análisis de sus interferencias en las reacciones de hidratación de los cementos portland; así como para la evaluación de las propiedades resistentes y duraderas que pueden conferirle a los hormigones, morteros o pastas de los que formen parte. Este trabajo versará sobre los efectos que produce la incorporación de tres puzolanas naturales a dos cementos portland de muy diferente composición mineralógica. Las técnicas aplicadas para su estudio han sido: la calorimetría de conducción y el ensayo de Fratini. Los resultados obtenidos permiten determinar

The impact of zirconium oxide radiopacifier on the early hydration behaviour of white Portland cement

International Nuclear Information System (INIS)

Coleman, Nichola J.; Li, Qiu

2013-01-01

Zirconium oxide has been identified as a candidate radiopacifying agent for use in Portland cement-based biomaterials. During this study, the impact of 20 wt.% zirconium oxide on the hydration and setting reactions of white Portland cement (WPC) was monitored by powder X-ray diffraction (XRD), 29 Si and 27 Al magic angle spinning nuclear magnetic resonance spectroscopy (MAS NMR), transmission electron microscopy (TEM) and Vicat apparatus. The presence of 20 wt.% zirconium oxide particles in the size-range of 0.2 to 5 μm was found to reduce the initial and final setting times of WPC from 172 to 147 min and 213 to 191 min, respectively. Zirconium oxide did not formally participate in the chemical reactions of the hydrating cement; however, the surface of the zirconium oxide particles presented heterogeneous nucleation sites for the precipitation and growth of the early C-S-H gel products which accelerated the initial setting reactions. The presence of zirconium oxide was found to have little impact on the development of the calcium (sulpho)aluminate hydrate phases. - Highlights: ► This is the first study of Portland cement-based biomaterials by 27 Al and 29 Si NMR. ► 20 wt.% ZrO 2 radiopacifier accelerates the early cement hydration reactions. ► Extent of hydration after 6 h is increased from 5.7% to 15% in the presence of ZrO 2 . ► Initial and final setting times are reduced by 25 and 22 min, respectively. ► ZrO 2 provides nucleation sites for the precipitation of early hydration products.

Research on the nanolevel influence of surfactants on structure formation of the hydrated Portland cement compositions

Directory of Open Access Journals (Sweden)

Guryanov Alexander

2016-01-01

Full Text Available The research of the structure formation process on a nanolevel of the samples of hydrated Portland cement compositions containing the modifying additives has been conducted with the help of small angle neutron scattering method. Carbonate and aluminum alkaline slimes as well as the complex additives containing surfactants were used as additives. The influence of slimes and surfactants on structural parameters change of Portland cement compositions of the average size of the disseminating objects, fractal dimension samples is considered. These Portland cement compositions are shown to be fractal clusters.

Social Vulnerability Index (SoVI) for Oregon based on 2000 Census Block Groups

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This data depicts the social vulnerability of Oregon census block groups to environmental hazards. Data were culled primarily from the 2000 Decennial Census.

Pulp tissue response to Portland cement associated with different radio pacifying agents on pulpotomy of human primary molars.

Science.gov (United States)

Marques, N; Lourenço Neto, N; Fernandes, A P; Rodini, C; Hungaro Duarte, M; Rios, D; Machado, M A; Oliveira, T

2015-12-01

The objective of this research was to evaluate the response of Portland cement associated with different radio pacifying agents on pulp treatment of human primary teeth by clinical and radiographic exams and microscopic analysis. Thirty mandibular primary molars were randomly divided into the following groups: Group I - Portland cement; Group II - Portland cement with iodoform (Portland cement + CHI3 ); Group III - Portland cement with zirconium oxide (Portland cement + ZrO2 ); and treated by pulpotomy technique (removal of a portion of the pulp aiming to maintain the vitally of the remaining radicular pulp tissue using a therapeutic dressing). Clinical and radiographic evaluations were recorded at 6, 12 and 24 months follow-up. The teeth at the regular exfoliation period were extracted and processed for histological analysis. Data were tested using statistical analysis with a significance level of 5%. The microscopic findings were descriptively analysed. All treated teeth were clinically and radiographically successful at follow-up appointments. The microscopic analysis revealed positive response to pulp repair with hard tissue barrier formation and pulp calcification in the remaining roots of all available teeth. The findings of this study suggest that primary teeth pulp tissue exhibited satisfactory biological response to Portland cement associated with radio pacifying agents. However, further studies with long-term follow-up are needed to determine the safe clinical indication of this alternative material for pulp therapy of primary teeth. © 2015 The Authors Journal of Microscopy © 2015 Royal Microscopical Society.

Partial replacement of Portland cement by red ceramic waste in mortars: study of pozzolanic activity

International Nuclear Information System (INIS)

Silva, A.R. da; Cabral, K.C.; Pinto, E.N. de M.G.l.

2016-01-01

The objective of this study is to analyze the pozzolanic activity of red ceramic residue on the partial replacement of Portland cement in mortars. The mortars were prepared by substituting 25% of the Portland cement for ground of ceramic residue with water cement’s factor of 0.48. The concrete used to construct the reference mortars and those with addiction was CPII-Z-32 (compound of Portland pozzolana cement). The chemical analysis and physical ceramic waste showed that this meets the requirements of NBR12653 (2014) for use as pozzolanic material. The pozzolanic activity index (IAP) obtained for the ceramic waste to twenty-eight days cure rate was 80.28%. (author)

76 FR 37059 - Siuslaw National Forest; Oregon; Oregon Dunes NRA Management Area 10 (C) Route and Area Designation

Science.gov (United States)

2011-06-24

... DEPARTMENT OF AGRICULTURE Forest Service Siuslaw National Forest; Oregon; Oregon Dunes NRA Management Area 10 (C) Route and Area Designation AGENCY: Forest Service, USDA. ACTION: Notice of intent to... (C) today are not designated routes. This has in turn led to greater and unnecessary impacts to...

Root perforations treatment using mineral trioxide aggregate and Portland cements.

Science.gov (United States)

Silva Neto, José Dias da; Brito, Rafael Horácio de; Schnaider, Taylor Brandão; Gragnani, Alfredo; Engelman, Mírian; Ferreira, Lydia Masako

2010-12-01

Clinical, radiological and histological evaluation of root perforations treated with mineral trioxide aggregate (MTA) or Portland cements, and calcium sulfate barrier. One molar and 11 premolar teeth of a male mongrel dog received endodontic treatment and furcations were perforated with a high-speed round bur and treated with a calcium sulfate barrier. MTA, Portland cement type II (PCII) and type V (PCV), and white Portland cement (WPC) were used as obturation materials. The teeth were restored with composite resin and periapical radiographs were taken. The animal was euthanized 120 days post-surgery for treatment evaluation. Right lower first premolar (MTA), right lower third premolar (PCV), left lower second premolar (MTA), and right lower second premolar (WPC): clinically normal, slightly radio-transparent area on the furcation, little inflammatory infiltrate, and new-bone formation. Left lower third premolar (PCII), right upper first premolar (WPC), right upper third premolar (PCII), and left upper first molar (PCV): clinically normal, radiopaque area on the furcation, and new-bone formation. Right upper second premolar (MTA), left upper second premolar (WPC), left upper third premolar (PCII): presence of furcation lesion, large radiolucent area, and intense inflammatory infiltrate. All obturation materials used in this study induced new-bone formation.

Using an epiphytic moss to identify previously unknown sources of atmospheric cadmium pollution

International Nuclear Information System (INIS)

Donovan, Geoffrey H.; Jovan, Sarah E.; Gatziolis, Demetrios; Burstyn, Igor; Michael, Yvonne L.; Amacher, Michael C.; Monleon, Vicente J.

2016-01-01

Urban networks of air-quality monitors are often too widely spaced to identify sources of air pollutants, especially if they do not disperse far from emission sources. The objectives of this study were to test the use of moss bio-indicators to develop a fine-scale map of atmospherically-derived cadmium and to identify the sources of cadmium in a complex urban setting. We collected 346 samples of the moss Orthotrichum lyellii from deciduous trees in December, 2013 using a modified randomized grid-based sampling strategy across Portland, Oregon. We estimated a spatial linear model of moss cadmium levels and predicted cadmium on a 50 m grid across the city. Cadmium levels in moss were positively correlated with proximity to two stained-glass manufacturers, proximity to the Oregon–Washington border, and percent industrial land in a 500 m buffer, and negatively correlated with percent residential land in a 500 m buffer. The maps showed very high concentrations of cadmium around the two stained-glass manufacturers, neither of which were known to environmental regulators as cadmium emitters. In addition, in response to our findings, the Oregon Department of Environmental Quality placed an instrumental monitor 120 m from the larger stained-glass manufacturer in October, 2015. The monthly average atmospheric cadmium concentration was 29.4 ng/m"3, which is 49 times higher than Oregon's benchmark of 0.6 ng/m"3, and high enough to pose a health risk from even short-term exposure. Both stained-glass manufacturers voluntarily stopped using cadmium after the monitoring results were made public, and the monthly average cadmium levels precipitously dropped to 1.1 ng/m"3 for stained-glass manufacturer #1 and 0.67 ng/m"3 for stained-glass manufacturer #2. - Highlights: • Bio-indicators are a valid method for measuring atmospheric pollutants • We used moss to map atmospheric cadmium in Portland, Oregon • Using a spatial linear model, we identified two stained

Creating Open Textbooks: A Unique Partnership Between Oregon State University Libraries and Press and Open Oregon State

Directory of Open Access Journals (Sweden)

Faye A. Chadwell

2016-05-01

Full Text Available This article presents Oregon State University’s experience launching an innovative Open Textbook initiative in spring 2014. The partners, Open Oregon State and the Oregon State University Libraries and Press, aimed to reduce the cost of course materials for students while ensuring the content created was peer-reviewed and employed multimedia capabilities. This initiative sought to showcase existing and emerging disciplinary strengths of the University thus creating unique course content that could be shared globally. This article briefly describes the U.S. landscape for open textbook creation and adoption. It demonstrates how this unique partnership has developed, covering barriers and benefits, and what the future could hold for new projects.

School-based mental health services, suicide risk and substance use among at-risk adolescents in Oregon.

Science.gov (United States)

Paschall, Mallie J; Bersamin, Melina

2018-01-01

This study examined whether an increase in the availability of mental health services at school-based health centers (SBHCs) in Oregon public schools was associated with the likelihood of suicidal ideation, suicide attempts and substance use behaviors among adolescents who experienced a depressive episode in the past year. The study sample included 168 Oregon public middle and high schools and 9073 students who participated in the Oregon Healthy Teens Survey (OHT) in 2013 and 2015. Twenty-five schools had an SBHC, and 14 of those schools increased availability of mental health services from 2013 to 2015. The OHT included questions about having a depressive episode, suicidal ideation, attempting suicide in the past year, and substance use behaviors in the past 30days. Multi-level logistic regression analyses were conducted in 2017 to examine associations between increasing mental health services and the likelihood of these outcomes. Analysis results indicated that students at SBHC schools that increased mental health services were less likely to report any suicidal ideation [odds ratio (OR) (95% C.I.)=0.66 (0.55, 0.81)], suicide attempts [OR (95% C.I.)=0.71 (0.56, 0.89)] and cigarette smoking [OR (95% C.I.)=0.77 (0.63, 0.94)] from 2013 to 2015 compared to students in all other schools. Lower frequencies of cigarette, marijuana and unauthorized prescription drug use were also observed in SBHC schools that increased mental health services relative to other schools with SBHCs. This study suggests that mental health services provided by SBHCs may help reduce suicide risk and substance use behaviors among at-risk adolescents. Copyright © 2017 Elsevier Inc. All rights reserved.

Alternatieven voor Portland Cement in ontwikkelingslanden onderzocht : continue-kalkoven maakt toepassing van kalk pozzolaan cement mogelijk

NARCIS (Netherlands)

Egmond - de Wilde De Ligny, van E.L.C.; Jongsma, Ivo

1995-01-01

In de discussie over bouwmaterialen in ontwikkelingslanden wordt vaak gepleit voor alternatieven voor Portland Cement. De productie van Portland Cement is kapitaal- en energie-intensief en draagt weinig bij aan de ontwikkeling van deze landen. De klein schaliger productie van alternatieven voor

Hydration rate and strength development of low-heat type portland cement mortar mixed with pozzolanic materials

International Nuclear Information System (INIS)

Matsui, Jun

1998-01-01

Recently, low-heat type Portland cement was specified in Japan Industrial Standards (JIS). Its hydration proceeds slowly. The results of the research so far obtained indicate that slow hydration of cement and mixing of pozzolanic materials with cement make micro-structure of harded cement paste dense and durable. In this study, a blended cement using low-heat type Portland cement and some of pozzolanic materials has been newly developed and its strength property and hydration ratio were checked. The followings are conclusion. (1) Hydration rate of cement paste varies with the replacement ratio of pozzolanic materials. (2) A good liner relationship between strength and total hydration rate of cement paste was observed. (3) A proper replacement ratio of both base-cement and pozzolanic material for manufacturing a blended cement is 50%. (author)

Development of Mix Design Method in Efforts to Increase Concrete Performance Using Portland Pozzolana Cement (PPC)

Science.gov (United States)

Krisnamurti; Soehardjono, A.; Zacoeb, A.; Wibowo, A.

2018-01-01

Earthquake disaster can cause infrastructure damage. Prevention of human casualties from disasters should do. Prevention efforts can do through improving the mechanical performance of building materials. To achieve high-performance concrete (HPC), usually used Ordinary Portland Cement (OPC). However, the most widely circulating cement types today are Portland Pozzolana Cement (PPC) or Portland Composite Cement (PCC). Therefore, the proportion of materials used in the HPC mix design needs to adjust to achieve the expected performance. This study aims to develop a concrete mix design method using PPC to fulfil the criteria of HPC. The study refers to the code/regulation of concrete mixtures that use OPC based on the results of laboratory testing. This research uses PPC material, gravel from Malang area, Lumajang sand, water, silica fume and superplasticizer of a polycarboxylate copolymer. The analyzed information includes the investigation results of aggregate properties, concrete mixed composition, water-binder ratio variation, specimen dimension, compressive strength and elasticity modulus of the specimen. The test results show that the concrete compressive strength achieves value between 25 MPa to 55 MPa. The mix design method that has developed can simplify the process of concrete mix design using PPC to achieve the certain desired performance of concrete.

Exploratory characterization of volcanic ash sourced from Uganda as a pozzolanic material in portland cement concrete

NARCIS (Netherlands)

Buregyeya, A.; Quercia Bianchi, G.; Spiesz, P.R.; Florea, M.V.A.; Nassingwa, R.; Uzoegbo, H.C.; Schmidt, W.

2013-01-01

The need for alternative cementing materials to ordinary Portland cement (OPC) has promoted characterization research on pozzolana as an important ingredient in cement production. In Uganda, natural pozzolana application in cement production is done by only two producers of Portland cement and at a

Effect of addition of Sikament-R superplasticizer on the hydration characteristics of portland cement pastes

Directory of Open Access Journals (Sweden)

Safaa.M. El Gamal

2012-08-01

Full Text Available The effect of addition of Sikament-R superplasticizer (modified lignosulphonate base on the hydration characteristics of hardened Portland cement pastes were studied at different curing conditions. Four mixtures were prepared using 0, 0.2, 0.4 and 0.6 wt% addition of Sikament-R superplasticizer (SR of cement. These pastes were hydrated under two different conditions; (i normal curing at room temperature; 25 °C up to 90 days periods and (ii hydrothermal curing at a pressure of 8 atm. of saturated steam up to 24 h. The compressive strength, combined water content, free lime content, gel/space ratio and microstructure of hardened cement pastes were studied. The results revealed that addition of SR superplasticizer promote the dispersion of cement particles and interacts with Ca(OH2. The addition of SR superplasticizer exhibits Portland cement better workability during the preparation of pastes. In addition, amore compact structure were obtained leading to higher values of compressive strength for all the hardened hydrated pastes under both normal and hydrothermal curing. The results indicated that the addition of SR superplasticizer to Portland cement does not alter the types of hydration products formed during normal or hydrothermal conditions; only it caused a decrease in the degree of the porosity of the formed pastes.

Natural History of Oregon Coast Mammals

Science.gov (United States)

Chris Maser; Bruce R. Mate; Jerry F. Franklin; C.T. Dyrness

1981-01-01

The book presents detailed information on the biology, habitats, and life histories of the 96 species of mammals of the Oregon coast. Soils, geology, and vegetation are described and related to wildlife habitats for the 65 terrestrial and 31 marine species. The book is not simply an identification guide to the Oregon coast mammals but is a dynamic portrayal of their...

Physical and Thermodynamical Properties of Water Phases in Hardening Portland Cement Systems

DEFF Research Database (Denmark)

Hansen, T. Bæk

The present study is devoted to the description of water phases in hardening portland cement paste systems containing a significant amount of micro-filler and having a low to moderate water/powder ratio. Emphasis has been placed on the early stages of the hardening process.......The present study is devoted to the description of water phases in hardening portland cement paste systems containing a significant amount of micro-filler and having a low to moderate water/powder ratio. Emphasis has been placed on the early stages of the hardening process....

City of Portland: Businesses for an environmentally sustainable tomorrow

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

The sustainable business development program in Portland (OR) is known as BEST. BEST stands for Businesses for an Environmentally Sustainable Tomorrow. The Portland Energy Office operates BEST as a {open_quotes}one-stop service center{close_quotes} for business owners and managers. BEST provides information and assistance on resource efficient buildings and business practices. The results of BEST`s two years of operation have been generally impressive. Nearly 150 new or expanding businesses have been connected with utility design assistance programs. Businesses have also received assistance with water conservation, telecommuting, construction debris recycling, and alternative fuel vehicles. BEST has received local and national publicity and BEST services have been the topic at more than a dozen conferences, meetings, or other speaking engagements. A guidebook for communities wishing to start a similar program will be available in early 1996.

Concentration of electrolyte reserves of the juvenile african catfish clarias gariepinus (burchell, 1822) exposed to sublethal concentrations of portland cement powder in solution

International Nuclear Information System (INIS)

Adamu, M.K.; Francis, O.A.

2008-01-01

The study investigated the effect of sublethal concentrations (39.10, 19.55, 9.87 and 0.00 mg/l) of Portland cement powder in solution on the electrolyte reserves (sodium, potassium, calcium, chloride and inorganic phosphorus) in the serum, liver and kidney of the juvenile African catfish Clarias gariepinus after a 15 day exposure period. The basic function of the determined electrolyte reserves in the body lies in controlling fluid distribution, intra and extra cellular acidobasic equilibrium, maintaining osmotic pressure of body fluid and normal neuro-muscular irritability. The result revealed significant (P 0.05) changes in inorganic phosphorus. Sodium, calcium, chloride and inorganic phosphorus and potassium were significantly (P 0.05) different in liver and kidney, respectively. Ipso-facto, the effector organs viz: liver and kidney of teleost species - Clarias gariepinus which are primarily responsible for regulating water and ionic movement between external and internal milieu of fishes are susceptible to deleterious effects of Portland cement powder thus sublethal concentration (39.10 mg/l) of Portland cement powder in solution after a 15 day exposure has been most toxic and debilitating to the test fish. (author)

77 FR 26275 - Bonneville Power Administration; Montana-to-Washington Transmission System Upgrade Project EIS

Science.gov (United States)

2012-05-03

..., Portland, Oregon 97208-3621; toll-free telephone 1-800-282-3713; direct telephone 360- 619-6178; or email... citizens, special interest groups, local and federal governments, and any other interested parties are...

50 CFR 2.2 - Locations of regional offices.

Science.gov (United States)

2010-10-01

... Federal Complex, 911 N.E. 11th Avenue, Portland, Oregon 97232. (b) Albuquerque Regional Office (Region 2... Carolina, South Carolina and Tennessee; the Commonwealth of Puerto Rico; and the Virgin Islands and...

Effect of wastewater on properties of Portland pozzolana cement

Science.gov (United States)

Babu, G. Reddy

2017-07-01

This paper presents the effect of wastewaters on properties of Portland pozzolana cement (PPC). Fourteen water treatment plants were found out in the Narasaraopet municipality region in Guntur district, Andhra Pradesh, India. Approximately, from each plant, between 3500 and 4000 L/day of potable water is selling to consumers. All plants are extracting ground water and treating through Reverse Osmosis (RO) process. During water treatment, plants are discharging approximately 1,00,000 L/day as wastewater in side drains in Narasaraopet municipality. Physical and chemical analysis was carried out on fourteen plants wastewater and distilled water as per producer described in APHA. In the present work, based on the concentrations of constituent's in wastewater, four typical plants i.e., Narasaraopeta Engineering College (NECWW), Patan Khasim Charitable Trust (PKTWW), Mahmadh Khasim Charitable Trust (MKTWW) and Amara (ARWW) were considered. The performance of four plants wastewater on physical properties i.e., setting times, compressive strength, and flexural strength of Portland pozzolana Cement (PPC) were performed in laboratories and compared same with reference specimens i.e., made with Distilled Water (DW) as mixing water. No significant change was observed in initial and finial setting time but setting times of selected wastewaters were retarded as compared to that of reference water. Almost, no change was observed in 90 days compressive and flexural strengths in four plants wastewaters specimens compared to that of reference water specimens. XRD technique was employed to find out main hydration compounds formed in the process.

Structure investigations on Portland cement paste by small angle neutron scattering

International Nuclear Information System (INIS)

Dragolici, C.A.; Lin, A.

2004-01-01

Hydrated Portland cement is a very complex material. Cement paste consists of many crystalline and non-crystalline phases in various ranges of sizes (μm and nm scale). The crystalline phases are embedded in amorphous phases of hydration products. We investigated the structural changes of hydrating phases in a time interval up to 18 days, at Budapest Neutron Center's SANS spectrometer. The small angle neutron scattering of Portland cements prepared with a various water-to-cement ratios, gave us information about the microstructure changes in the material. Fractals were a suitable way for structure modelling. Some comments regarding the opportunity of using the most common models are pointed out. (authors)

Teaching Biochemistry Online at Oregon State University

Science.gov (United States)

Ahern, Kevin

2017-01-01

A strategy for growing online biochemistry courses is presented based on successes in ecampus at Oregon State University. Four free drawing cards were key to the effort--YouTube videos, iTunes U online free course content, an Open Educational Resource textbook--Biochemistry Free and Easy, and a fun set of educational songs known as the Metabolic…

Status of Oregon's Bull Trout.

Energy Technology Data Exchange (ETDEWEB)

Buchanan, David V.; Hanson, Mary L.; Hooton, Robert M.

1997-10-01

Limited historical references indicate that bull trout Salvelinus confluentus in Oregon were once widely spread throughout at least 12 basins in the Klamath River and Columbia River systems. No bull trout have been observed in Oregon's coastal systems. A total of 69 bull trout populations in 12 basins are currently identified in Oregon. A comparison of the 1991 bull trout status (Ratliff and Howell 1992) to the revised 1996 status found that 7 populations were newly discovered and 1 population showed a positive or upgraded status while 22 populations showed a negative or downgraded status. The general downgrading of 32% of Oregon's bull trout populations appears largely due to increased survey efforts and increased survey accuracy rather than reduced numbers or distribution. However, three populations in the upper Klamath Basin, two in the Walla Walla Basin, and one in the Willamette Basin showed decreases in estimated population abundance or distribution.

Reaction of rat subcutaneous tissue to mineral trioxide aggregate and Portland cement: a secondary level biocompatibility test.

Science.gov (United States)

Karanth, P; Manjunath, M K; Kuriakose, E S

2013-01-01

This secondary-level animal study was conducted to assess and compare the subcutaneous tissue reaction to implantation of white mineral trioxide aggregate (MTA) and white Portland cement. Polyethylene tubes filled with either freshly mixed white MTA (Group I) or white Portland cement (Group II) were implanted subcutaneously into 12 Wistar Albino rats. Each animal also received an empty polyethylene tube as the control (Group III). After 7, 14, 21 and 30 days, the implants, together with surrounding tissues were excised. Two pathologists blinded to the experimental procedure, evaluated sections taken from the biopsy specimens for the severity of the inflammatory response, calcification and the presence and thickness of fibrous capsule surrounding the implant. Statistical analysis was performed using the Cross-tabs procedure, Univariate analysis of the variance two-way and the Pearson product moment correlation to assess inter-rater variability between the two evaluators. At 7 days, there was no significant difference in the severity of inflammation between the control group, white MTA, and white Portland cement groups. In the 14 day, 21 day and 30 day test periods, control group had significantly less inflammation than white MTA and white Portland cement. There was no significant difference in the grading of inflammation between white MTA and white Portland cement. All materials exhibited thick capsule at 7 days and thin capsule by 30 days. Both white MTA and white Portland cement were not completely non-irritating at the end of 30 days as evidenced by the presence of mild inflammation. However, the presence of a thin capsule around the materials, similar to the control group, indicates good tissue tolerance. White MTA and white Portland cement seem to be materials of comparable biocompatibility.

Measurements of CO2 Mole Fractionand δ13C in Archived Air Samples from Cape Meares, Oregon (USA) 1977 - 1998

Science.gov (United States)

Clark, O.; Rice, A. L.

2017-12-01

Carbon dioxide (CO2) is the most abundant, anthropogenically forced greenhouse gas (GHG) in the global atmosphere. Emissions of CO2 account for approximately 75% of the world's total GHG emissions. Atmospheric concentrations of CO2 are higher now than they've been at any other time in the past 800,000 years. Currently, the global mean concentration exceeds 400 ppm. Today, global networks regularly monitor CO2 concentrations and isotopic composition (δ13C and δ18O). However, past data is sparse. Over 200 ambient air samples from Cape Meares, Oregon (45.5°N, 124.0°W), a coastal site in Western United States, were obtained by researchers at Oregon Institute of Science and Technology (OGI, now Oregon Health & Science University), between the years of 1977 and 1998 as part of a global monitoring program of six different sites in the polar, middle, and tropical latitudes of the Northern and Southern Hemispheres. Air liquefaction was used to compress approximately 1000L of air (STP) to 30bar, into 33L electropolished (SUMMA) stainless steel canisters. Select archived air samples from the original network are maintained at Portland State University (PSU) Department of Physics. These archived samples are a valuable look at changing atmospheric concentrations of CO2 and δ13C, which can contribute to a better understanding of changes in sources during this time. CO2 concentrations and δ13C of CO2 were measured at PSU, with a Picarro Cavity Ringdown Spectrometer, model G1101-i analytical system. This study presents the analytical methods used, calibration techniques, precision, and reproducibility. Measurements of select samples from the archive show rising CO2 concentrations and falling δ13C over the 1977 to 1998 period, compatible with previous observations and rising anthropogenic sources of CO2. The resulting data set was statistically analyzed in MATLAB. Results of preliminary seasonal and secular trends from the archive samples are presented.

EnviroAtlas - Portland, ME - BenMAP Results by Block Group

Data.gov (United States)

U.S. Environmental Protection Agency — This EnviroAtlas dataset demonstrates the effect of changes in pollution concentration on local populations in 146 block groups in Portland, Maine. The US EPA's...

Alkali segregation in Portland cement pastes

Directory of Open Access Journals (Sweden)

Triviño, F.

1966-09-01

Full Text Available Not availableEn el presente trabajo se pone de manifiesto experimentalmente la formación y presencia de aphthitalita -sulfato doble de potasio y sodio en la relación S04K2/S04Na2 = 3/1 en las pastas puras de cemento portland, desde el comienzo del fraguado de las mismas. Se estudia el mecanismo de la citada formación, íntimamente relacionada con el proceso general de formación de eflorescencias salinas, a base de una emigración de sulfatos alcalinos hacia las partes externas de las pastas, en virtud de fenómenos de exudación equivalentes a arrastres capilares. Se sintetiza y aísla la aphthitalita por dos procedimientos y se obtiene su difractograma.de rayos· X, a efectos de su identificación y de la confirmación de los resultados experimentales obtenidos, así como de la interpretación de los mismos.

Longitudinal and seasonal changes in functional organization of macroinvertebrate communities in four Oregon streams.

OpenAIRE

Hawkins, C. P.; Sedell, J. R.

1981-01-01

Relative numerical dominance and densities of invertebrate functional feeding groups are compared with longitudinal and seasonal changes in food resources in a Cascade Range stream system in Oregon. We also compare our data with hypothetical predictions of the River Continuum model. We found that both relative abundances and densities of functional groups fit qualitative characterization of stream reaches and the River Continuum model: Shredders dominated upper shaded reaches; scrapers were m...

Solidification of oils and organic liquids

International Nuclear Information System (INIS)

Clark, D.E.; Colombo, P.; Neilson, R.M. Jr.

1982-07-01

The suitability of selected solidification media for application in the disposal of low-level oil and other organic liquid wastes has been investigated. In the past, these low-level wastes (LLWs) have commonly been immobilized by sorption onto solid absorbents such as vermiculite or diatomaceous earth. Evolving regulations regarding the disposal of these materials encourage solidification. Solidification media which were studied include Portland type I cement; vermiculite plus Portland type I cement; Nuclear Technology Corporation's Nutek 380-cement process; emulsifier, Portland type I cement-sodium silicate; Delaware Custom Materiel's cement process; and the US Gypsum Company's Envirostone process. Waste forms have been evaluated as to their ability to reliably produce free standing monolithic solids which are homogeneous (macroscopically), contain < 1% free standing liquids by volume and pass a water immersion test. Solidified waste form specimens were also subjected to vibratory shock testing and flame testing. Simulated oil wastes can be solidified to acceptable solid specimens having volumetric waste loadings of less than 40 volume-%. However, simulated organic liquid wastes could not be solidified into acceptable waste forms above a volumetric loading factor of about 10 volume-% using the solidification agents studied

Field-trip guide to the geologic highlights of Newberry Volcano, Oregon

Science.gov (United States)

Jensen, Robert A.; Donnelly-Nolan, Julie M.

2017-08-09

River. Because of Newberry Volcano’s proximity to populated areas, the presence of hot springs within the caldera, and the long and recent history of eruptive activity (including explosive activity), the U.S. Geological Survey installed monitoring equipment on the volcano. A recent geophysical study indicates the presence of magma at 3 to 5 km beneath the caldera.The writing of this guide was prompted by a field trip to Crater Lake and Newberry Volcano organized in conjunction with the August 2017 IAVCEI quadrennial meeting in Portland, Oregon. Both field trip guides are available online. These two volcanoes were grouped in a single field trip because they are two of the few Cascades volcanoes that have generated calderas and significant related tephra deposits.

Oregon's experience with aid in dying: findings from the death with dignity laboratory.

Science.gov (United States)

Coombs Lee, Barbara

2014-11-01

With passage of the Death with Dignity Act in 1994, Oregon became the first jurisdiction to authorize and regulate aid in dying. Data from that experience are comprehensive and bountiful, and answer a multitude of questions and concerns about whether the benefits of recognizing the medical practice of aid in dying justify the risks. An exhaustive description of findings from Oregon's aid-in-dying experience is beyond the scope of this or any single article on the subject. This article provides a summary of data highlights, gleaned from scientific investigations and governmental reporting. It organizes highlighted reports along subjects so that readers may see what various sources have to teach on a number of questions important to policy makers. © 2014 New York Academy of Sciences.

2012 Oregon Lidar Consortium (OLC) Lidar: Keno (OR)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Watershed Sciences, Inc. (WSI) collected Light Detection and Ranging (LiDAR) data of the Oregon Keno Study Area for the Oregon Department of Geology and Mineral...

Precisely locating the Klamath Falls, Oregon, earthquakes

Science.gov (United States)

Qamar, A.; Meagher, K.L.

1993-01-01

The Klamath Falls earthquakes on September 20, 1993, were the largest earthquakes centered in Oregon in more than 50 yrs. Only the magnitude 5.75 Milton-Freewater earthquake in 1936, which was centered near the Oregon-Washington border and felt in an area of about 190,000 sq km, compares in size with the recent Klamath Falls earthquakes. Although the 1993 earthquakes surprised many local residents, geologists have long recognized that strong earthquakes may occur along potentially active faults that pass through the Klamath Falls area. These faults are geologically related to similar faults in Oregon, Idaho, and Nevada that occasionally spawn strong earthquakes. 

Assessment of Pollution Potentialities of some Portland Cement ...

African Journals Online (AJOL)

Chemical analysis of some Portland cement commonly used in Nigeria was carried out. All the cement studies were found to be good for concrete work especially where no special property is required. The concentration levels of heavy metals in all the cement samples were above the tolerance limit and therefore need to ...

A thermodynamic approach to the hydration of sulphate-resisting Portland cement

International Nuclear Information System (INIS)

Lothenbach, Barbara; Wieland, Erich

2006-01-01

A thermodynamic approach is used to model changes in the hydrate assemblage and the composition of the pore solution during the hydration of calcite-free and calcite-containing sulphate-resisting Portland cement CEM I 52.5 N HTS. Modelling is based on thermodynamic data for the hydration products and calculated hydration rates for the individual clinker phases, which are used as time-dependent input parameters. Model predictions compare well with the composition of the hydrate assemblage as observed by TGA and semi-quantitative XRD and with the experimentally determined compositions of the pore solutions. The calculations show that in the presence of small amounts of calcite typically associated with Portland cement, C-S-H, portlandite, ettringite and calcium monocarbonate are the main hydration products. In the absence of calcite in the cement, however, siliceous hydrogarnet instead of calcium monocarbonate is observed to precipitate. The use of a higher water-to-cement ratio for the preparation of a calcite-containing cement paste has a minor effect on the composition of the hydrate assemblage, while it significantly changes the composition of the pore solution. In particular, lower pH value and higher Ca concentrations appear that could potentially influence the solubility and uptake of heavy metals and anions by cementitious materials

76 FR 12370 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-Portland Cement...

Science.gov (United States)

2011-03-07

... Production Act of 1993--Portland Cement Association Notice is hereby given that, on February 02, 2011... seq. (``the Act''), Portland Cement Association (``PCA'') has filed written notifications..., Praxair, Danbury, CT; Metso Minerals, York, PA; Lehigh Cement Company LLC, Allentown, PA; Lehigh Northwest...

76 FR 34252 - Notice Pursuant to the National Cooperative Research and Production Act of 1993; Portland Cement...

Science.gov (United States)

2011-06-13

... Production Act of 1993; Portland Cement Association Notice is hereby given that, on May 12, 2011, pursuant to.... (``the Act''), Portland Cement Association (``PCA'') has filed written notifications simultaneously with... plaintiffs to actual damages under specified circumstances. Specifically, Drake Cement, LLC, Scottsdale, AZ...

Trichinella surveillance in black bears (Ursus americanus) from Oregon, USA.

Science.gov (United States)

Mortenson, J A; Kent, M L; Fowler, D R; Chomel, B B; Immell, D A

2014-01-01

We used serology and muscle digestion to test black bears (Ursus americanus) from western Oregon, USA, for Trichinella. Results indicate black bears in Oregon are not part of a sylvatic cycle for Trichinella, and risk of human exposure to Trichinella larvae from eating black bear meat from Oregon appears low.

The Oregon Applied Academics Project: Final Report

Science.gov (United States)

Pearson, Donna; Richardson, George B.; Sawyer, Jennifer M.

2013-01-01

This report contains the findings of the Oregon Applied Academics research and development project which spanned three academic years from 2010 through 2013. The overall purpose of the project was to develop and implement a technical math course that would meet graduation requirements and improve student performance. The State of Oregon has been…

75 FR 21040 - Notice of Determinations Terminating Investigations of Petitions Regarding Eligibility To Apply...

Science.gov (United States)

2010-04-22

... Locks, Connecticut. TA-W-70,415: Gerber Legendary Blades, Portland, Oregon. TA-W-70,578: Industrial...., Central Islip, New York. TA-W-72,970: Hopper Industries, Inc., Logansport, Indiana. TA-W-72,994: Nautilus...

Structure investigations on Portland cement paste by small angle neutron scattering

International Nuclear Information System (INIS)

Dragolici, C. A.; Len, A.

2003-01-01

Portland cement pastes consist of many crystalline and non-crystalline phases in various ranges of sizes (nm and mm scale). The crystalline phases are embedded in amorphous phases of the hydration products. We investigated the structural changes of hydrating phases in the time interval of 1-30 days at Budapest Neutron Center's SANS diffractometer. The small angle neutron scattering of Portland cements prepared with a water-to-cement ratio from 0,3 to 0,8 gave us information about the microstructure changes in the material. Fractals were a suitable way for structure modelling. The variation of fractals size depending on the preparation-to-measurement time interval and water-to-cement ratio could be observed. (authors)

Compliance Monitoring of Underwater Blasting for Rock Removal at Warrior Point, Columbia River Channel Improvement Project, 2009/2010

Energy Technology Data Exchange (ETDEWEB)

Carlson, Thomas J.; Johnson, Gary E.; Woodley, Christa M.; Skalski, J. R.; Seaburg, Adam

2011-05-10

The U.S. Army Corps of Engineers, Portland District (USACE) conducted the 20-year Columbia River Channel Improvement Project (CRCIP) to deepen the navigation channel between Portland, Oregon, and the Pacific Ocean to allow transit of fully loaded Panamax ships (100 ft wide, 600 to 700 ft long, and draft 45 to 50 ft). In the vicinity of Warrior Point, between river miles (RM) 87 and 88 near St. Helens, Oregon, the USACE conducted underwater blasting and dredging to remove 300,000 yd3 of a basalt rock formation to reach a depth of 44 ft in the Columbia River navigation channel. The purpose of this report is to document methods and results of the compliance monitoring study for the blasting project at Warrior Point in the Columbia River.

75 FR 4423 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-Portland Cement...

Science.gov (United States)

2010-01-27

... Production Act of 1993--Portland Cement Association Notice is hereby given that, on December 14, 2009... seq. (``the Act''), Portland Cement Association (``PCA'') has filed written notifications... Cement, Hannibal, MO has been added as a party to this venture. Also, the following parties have...

Evaluation of Beginner Driver Education in Oregon

Directory of Open Access Journals (Sweden)

Dan Mayhew

2017-02-01

Full Text Available Although driver education (DE is widely accepted as an effective teen driver safety measure and widely available in the United States, Canada and elsewhere, evaluations have generally failed to show that such formal programs actually produce safer drivers. To address the issue of safety effects as part of a larger investigation, two studies were conducted to examine whether the Oregon Department of Transportation (ODOT-approved DE program was associated with reductions in collisions and convictions. In the first study, DE status among a relatively small sample of teens who completed an online survey was not found to have a significant effect on collisions and convictions. In the second study, of a much larger population of teen drivers, DE status was associated with a lower incidence of collisions and convictions. On balance, this suggests that the safety effects of DE are either neutral, based on the results of the first Oregon study, or cautiously optimistic based on the results of the second study. The implications of these findings are discussed in terms of making improvements in DE that are evidence-based, and the need for further evaluation to establish that improved and new programs meet their safety objectives.

The Oregon experiment--effects of Medicaid on clinical outcomes

NARCIS (Netherlands)

Baicker, K.; Taubman, S.L.; Allen, H.L.; Bernstein, M.; Gruber, J.H.; Newhouse, J.P.; Schneider, E.C.; Wright, B.J.; Zaslavsky, A.M.; Finkelstein, A.N.; Carlson, M.; Edlund, T.; Gallia, C.; Smith, J.; et al.,

2013-01-01

BACKGROUND: Despite the imminent expansion of Medicaid coverage for low-income adults, the effects of expanding coverage are unclear. The 2008 Medicaid expansion in Oregon based on lottery drawings from a waiting list provided an opportunity to evaluate these effects. METHODS: Approximately 2 years

Study of the bismuth oxide concentration required to provide Portland cement with adequate radiopacity for endodontic use.

Science.gov (United States)

Bueno, Carlos Eduardo da Silveira; Zeferino, Eduardo Gregatto; Manhães, Luiz Roberto Coutinho; Rocha, Daniel Guimarães Pedro; Cunha, Rodrigo Sanches; De Martin, Alexandre Sigrist

2009-01-01

The purpose of this study was to determine the ideal concentration of bismuth oxide in white Portland cement to provide it with sufficient radiopacity for use as an endodontic material (ADA specification #57). 2-mm thick standardized test specimens of white MTA and of white Portland cement, as controls, and of white Portland cement with the experimental addition of 5%, 10%, 15%, 20%, 25% or 30% of bismuth oxide were radiographed and compared with various thicknesses of pure aluminum, using optic density to determine the observed grayscale levels of radiopacity in a scale ranging from 0 to 255. The data was submitted to ANOVA (pcement with 0%, 5%, 10%, 15%, 20%, 25% and 30% of bismuth oxide presented mean readings of 63.3, 95.7, 110.7, 142.7, 151.3, 161.0 and 180.0 respectively. MTA presented a mean reading of 157.3. The readings of MTA and white Portland cement with 15% bismuth oxide did not differ significantly from the reading observed for a thickness of 4 mm of aluminum (145.3), which is considered ideal for a test specimen by ADA specification #57 (2 mm above the thickness of the test specimen). White MTA and white Portland cement with 15% bismuth oxide presented the radiopacity required for an endodontic cement.

78 FR 60220 - Safety Zone; Fireworks Display, Willamette River, Oregon City, OR

Science.gov (United States)

2013-10-01

... 1625-AA00 Safety Zone; Fireworks Display, Willamette River, Oregon City, OR AGENCY: Coast Guard, DHS... River south of the I-205 Bridge and north of the Oregon City Bridge, Oregon City, OR. The safety zone... safety zone: (1) Location. All waters of the Willamette River, Oregon City, OR, between the I-205 Bridge...

Assessment and refinement of real-time travel time algorithms for use in practice : final report, October 2008.

Science.gov (United States)

2008-10-01

The FHWA has strongly encouraged transportation departments to display travel times on their Dynamic Message Signs (DMS). The Oregon : Department of Transportation (ODOT) currently displays travel time estimates on three DMSs in the Portland metropol...

Rebuild America partner update, November--December 1998

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-11-01

This issue of the update includes articles on retrofitting Duke University facilities, energy efficiency updates to buildings in Portland, Oregon, Salisbury, North Carolina, Hawaii, Roanoke-Chowan, Virginia, and energy savings centered designs for lighting systems.

Oral microbiota species in acute apical endodontic abscesses

Directory of Open Access Journals (Sweden)

Noelle George

2016-03-01

Full Text Available Background and objectives: Acute apical abscesses are serious endodontic diseases resulting from pulpal infection with opportunistic oral microorganisms. The objective of this study was to identify and compare the oral microbiota in patients (N=18 exhibiting acute apical abscesses, originating from the demographic region in Portland, Oregon. The study hypothesis is that abscesses obtained from this demographic region may contain unique microorganisms not identified in specimens from other regions. Design: Endodontic abscesses were sampled from patients at the Oregon Health & Science University (OHSU School of Dentistry. DNA from abscess specimens was subjected to polymerase chain reaction amplification using 16S rRNA gene-specific primers and Cy3-dCTP labeling. Labeled DNA was then applied to microbial microarrays (280 species generated by the Human Oral Microbial Identification Microarray Laboratory (Forsyth Institute, Cambridge, MA. Results: The most prevalent microorganisms, found across multiple abscess specimens, include Fusobacterium nucleatum, Parvimonas micra, Megasphaera species clone CS025, Prevotella multisaccharivorax, Atopobium rimae, and Porphyromonas endodontalis. The most abundant microorganisms, found in highest numbers within individual abscesses, include F. nucleatum, P. micra, Streptococcus Cluster III, Solobacterium moorei, Streptococcus constellatus, and Porphyromonas endodontalis. Strong bacterial associations were identified between Prevotella multisaccharivorax, Acidaminococcaceae species clone DM071, Megasphaera species clone CS025, Actinomyces species clone EP053, and Streptococcus cristatus (all with Spearman coefficients >0.9. Conclusions: Cultivable and uncultivable bacterial species have been identified in endodontic abscesses obtained from the Portland, Oregon demographic region, and taxa identifications correlated well with other published studies, with the exception of Treponema and Streptococcus cristae, which

Oral microbiota species in acute apical endodontic abscesses.

Science.gov (United States)

George, Noelle; Flamiatos, Erin; Kawasaki, Kellie; Kim, Namgu; Carriere, Charles; Phan, Brian; Joseph, Raphael; Strauss, Shay; Kohli, Richie; Choi, Dongseok; Baumgartner, J Craig; Sedgley, Christine; Maier, Tom; Machida, Curtis A

2016-01-01

Acute apical abscesses are serious endodontic diseases resulting from pulpal infection with opportunistic oral microorganisms. The objective of this study was to identify and compare the oral microbiota in patients (N=18) exhibiting acute apical abscesses, originating from the demographic region in Portland, Oregon. The study hypothesis is that abscesses obtained from this demographic region may contain unique microorganisms not identified in specimens from other regions. Endodontic abscesses were sampled from patients at the Oregon Health & Science University (OHSU) School of Dentistry. DNA from abscess specimens was subjected to polymerase chain reaction amplification using 16S rRNA gene-specific primers and Cy3-dCTP labeling. Labeled DNA was then applied to microbial microarrays (280 species) generated by the Human Oral Microbial Identification Microarray Laboratory (Forsyth Institute, Cambridge, MA). The most prevalent microorganisms, found across multiple abscess specimens, include Fusobacterium nucleatum, Parvimonas micra, Megasphaera species clone CS025, Prevotella multisaccharivorax, Atopobium rimae, and Porphyromonas endodontalis. The most abundant microorganisms, found in highest numbers within individual abscesses, include F. nucleatum, P. micra, Streptococcus Cluster III, Solobacterium moorei, Streptococcus constellatus, and Porphyromonas endodontalis. Strong bacterial associations were identified between Prevotella multisaccharivorax, Acidaminococcaceae species clone DM071, Megasphaera species clone CS025, Actinomyces species clone EP053, and Streptococcus cristatus (all with Spearman coefficients >0.9). Cultivable and uncultivable bacterial species have been identified in endodontic abscesses obtained from the Portland, Oregon demographic region, and taxa identifications correlated well with other published studies, with the exception of Treponema and Streptococcus cristae, which were not commonly identified in endodontic abscesses between the

The 3d International Workshop on Computational Electronics

Science.gov (United States)

Goodnick, Stephen M.

1994-09-01

The Third International Workshop on Computational Electronics (IWCE) was held at the Benson Hotel in downtown Portland, Oregon, on May 18, 19, and 20, 1994. The workshop was devoted to a broad range of topics in computational electronics related to the simulation of electronic transport in semiconductors and semiconductor devices, particularly those which use large computational resources. The workshop was supported by the National Science Foundation (NSF), the Office of Naval Research and the Army Research Office, as well as local support from the Oregon Joint Graduate Schools of Engineering and the Oregon Center for Advanced Technology Education. There were over 100 participants in the Portland workshop, of which more than one quarter represented research groups outside of the United States from Austria, Canada, France, Germany, Italy, Japan, Switzerland, and the United Kingdom. There were a total 81 papers presented at the workshop, 9 invited talks, 26 oral presentations and 46 poster presentations. The emphasis of the contributions reflected the interdisciplinary nature of computational electronics with researchers from the Chemistry, Computer Science, Mathematics, Engineering, and Physics communities participating in the workshop.

Water-quality data for Smith and Bybee Lakes, Portland, Oregon, June to November, 1982

Science.gov (United States)

Clifton, Daphne G.

1983-01-01

Water-quality monitoring at Smith and Bybee Lakes included measurement of water temperature, dissolved oxygen concentration and percent saturation, pH, specific conductance, lake depth, alkalinity, dissolved carbon, total dissolved solids, secchi disk light transparency, nutrients, and chlorophyll a and b. In addition, phytoplankton, zooplankton, and benthic invertebrate populations were identified and enumerated. Lakebed sediment was analyzed for particle size, volatile solids, immediate oxygen demand, trace metals, total organic carbon, nutrients, and organic constituents. (USGS)

Solidification of ion exchange resins saturated with Na+ ions: Comparison of matrices based on Portland and blast furnace slag cement

Science.gov (United States)

Lafond, E.; Cau dit Coumes, C.; Gauffinet, S.; Chartier, D.; Stefan, L.; Le Bescop, P.

2017-01-01

This work is devoted to the conditioning of ion exchange resins used to decontaminate radioactive effluents. Calcium silicate cements may have a good potential to encapsulate spent resins. However, certain combinations of cement and resins produce a strong expansion of the final product, possibly leading to its full disintegration. The focus is placed on the understanding of the behaviour of cationic resins in the Na+ form in Portland or blast furnace slag (CEM III/C) cement pastes. During hydration of the Portland cement paste, the pore solution exhibits a decrease in its osmotic pressure, which causes a transient expansion of small magnitude of the resins. At 20 °C, this expansion takes place just after setting in a poorly consolidated material and is sufficient to induce cracks. In the CEM III/C paste, swelling of the resins also occurs, but before the end of setting, and induces limited stress in the matrix which is still plastic.

77 FR 5573 - Notice Pursuant to the National Cooperative Research and Production Act of 1993-Portland Cement...

Science.gov (United States)

2012-02-03

... Production Act of 1993--Portland Cement Association Notice is hereby given that, on January 6, 2012, pursuant... seq. (``the Act''), Portland Cement Association (``PCA'') has filed written notifications..., Newark, DE, has been added as a party to this venture. Also, Texas-Lehigh Cement Company, Buda, TX...

Addition of polyurethane dispersions to Portland G for oil wells steam injection submitted to vapor injection; Adicao de poliuretana em dispersao a Portland G para cimentacao de pocos de petroleo sujeitos a injecao de vapor

Energy Technology Data Exchange (ETDEWEB)

Silva, L.B. da; Lima, F.M. de; Martinelli, A.M.; Bezerra, U.T.; Mello, D.M.A. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Araujo, R.G.S. [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2004-07-01

Portland cement is by far the most important binding material used in oil well cementing. The cement sheath is responsible for both the mechanical stability of the wellbore and zonal isolation. During primary cementing and the production lifespan of the well, the cement sheath is exposed to adverse thermo-mechanical conditions, which may crack the intrinsically brittle cement material. Cracking affects the mechanical integrity of the sheath resulting in the contamination of oil or gas pay zones, as well as in the increase of producing costs related to the extraction of pebble and water. This scenario is especially encountered in wells containing heavy oils, typical of the Northeastern region of Brazil. The objective of the present study was to improve the fracture toughness of hardened Special Portland Cement slurries by the addition of aqueous polyurethane to Portland-based slurries used in primary cementing, plug backs and squeeze operations, improving environmental and economical impacts. The results revealed that the addition of polyurethane increased the viscosity of the slurry but still within the limits established by oil well cement guidelines. No significant increase was observed in the compressive strength of the cement. However, the addition of polyurethane improved the toughness of the cement increasing its ability to withstand thermo-mechanical cycles typical of heavy oil recovery. In addition, significant reduction in permeability was observed as the contents of polyurethane increased, contributing to the reduction in set time and gas migration through the cement sheath. (author)

Toxicity and Histopathological Effects of Portland Cement Powder in ...

African Journals Online (AJOL)

Hepatic lesions in the liver tissues of fish exposed to Portland cement powder in solution were characterized by degeneration of hepatocyte, vascuolization of cell cytoplasm, fatty degeneration and hypertrophy of hepatocytes. Histological comparison of tissues indicated that most damage occurred in the gill rather than in ...

7 CFR 927.103 - Organically produced pears.

Science.gov (United States)

2010-01-01

... Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE PEARS GROWN IN OREGON AND... means pears that have been certified by an organic certification organization currently registered with... under the National Organic Program. Communications ...

Utilization of steel slag for Portland cement clinker production.

Science.gov (United States)

Tsakiridis, P E; Papadimitriou, G D; Tsivilis, S; Koroneos, C

2008-04-01

The aim of the present research work is to investigate the possibility of adding steel slag, a by-product of the conversion of iron to steel process, in the raw meal for the production of Portland cement clinker. Two samples of raw meals were prepared, one with ordinary raw materials, as a reference sample ((PC)(Ref)), and another with 10.5% steel slag ((PC)(S/S)). Both raw meals were sintered at 1450 degrees C. The results of chemical and mineralogical analyses as well as the microscopic examination showed that the use of the steel slag did not affect the mineralogical characteristics of the so produced Portland cement clinker. Furthermore, both clinkers were tested by determining the grindability, setting times, compressive strengths and soundness. The hydration products were examined by XRD analysis at 2, 7, 28 and 90 days. The results of the physico-mechanical tests showed that the addition of the steel slag did not negatively affect the quality of the produced cement.

2013 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Scappoose

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI collected Light Detection and Ranging (LiDAR) data for the Oregon LiDAR Consortium (OLC) Scappoose study area. The Scappoose project area encompasses...

Effect of saliva and blood contamination on the bi-axial flexural strength and setting time of two calcium-silicate based cements: Portland cement and biodentine.

Science.gov (United States)

Alhodiry, W; Lyons, M F; Chadwick, R G

2014-03-01

This study evaluated the effect of contamination with saliva and blood on the bi-axial flexural strength and setting time of pure gray Portland cement and Biodentine (Septodont, Allington, UK). A one-way ANOVA showed that contamination caused no significant difference between the cements in bi-axial flexural strength (P> 0.05). However there was a significant difference in setting time (PPortland cement taking longer than Biodentine, regardless of the contaminant, and contamination with blood increased the setting time of both materials. Biodentine was similar in strength to Portland cement, but had a shorter setting time for both contaminated and non-contaminated samples.

Radiopacity and histological assessment of Portland cement plus bismuth oxide.

Science.gov (United States)

Coutinho-Filho, Tauby; De-Deus, Gustavo; Klein, Leila; Manera, Gisele; Peixoto, Carla; Gurgel-Filho, Eduardo Diogo

2008-12-01

The present study evaluated the subcutaneous connective tissue reactions and the radiopacity of MTA, Portland cement (PC), and Portland cement plus bismuth oxide (BO). Forty rats were divided into 5 groups (n = 8 per group): A1: Control (empty capsule); A2: Pro-Root MTA; A3: PC; A4: PC + BO 1:1; and A5: PC + BO 2:1. Polyethylene tubes were filled with the test materials and standardized radiographic images were taken. Histological evaluation was done after 7 and 60 days. Student t test and Fisher's test were used in the statistical analysis (P A4 > A5 > A3. No differences were found for the tissue response in the 2 experimental periods. A positive correlation between BO concentration and radiopacity of PC was determined. The histological evaluation suggests that all studied materials were biocompatible at 7 and 60 days.

Comparative study of the properties of ordinary portland cement ...

African Journals Online (AJOL)

The study explored metakaolin as alternative material to cement. It compares the properties of Ordinary Portland Cement (OPC) concrete and binary concrete containing metakaolin as partial replacement of OPC. Two set of concrete samples; one with 10% Metakaolin (MK) replacing OPC by weight, and the other without ...

Effectiveness of Property Tax Relief in Oregon.

Science.gov (United States)

Hartman, William T.; Hwang, C. S.

This study examines the effects of the 1979 Oregon Property Tax Relief Plan on 1980-81 school district budget decisions by comparing the available tax relief, the school expenditures, and the tax levies in the state for the years 1975-81. The history of direct and indirect property tax relief in Oregon is sketched for the years prior to 1979; the…

Celebrating 24 years of Public Outreach of Science and Engineering in Portland Oregon

Science.gov (United States)

Bristol, Terry

2012-02-01

There have been several core strategies in our highly successful 24-year Science, Technology and Society outreach program. However, the strategy for each season is also dynamic, requiring innovation and novel coalitions. As Bob Dylan put it so succinctly, ``He not busy being born is busy dying.'' Public outreach programs - as the Chautauquas of the past - should be positioned in the cultural milieu along with the opera, symphony and theatre. Support for the enterprise needs to be a broad and diverse coalition, based ideally on the creative formation of win-win relationship. You want people to see your success as their success: ``Together we can enhance the intellectual environment in ways that none of us could do alone.'' Being multi-disciplinary presents challenges but has considerable advantages. For instance, enlightened managers of established organizations recognize the value of exposing their employees to a diversity of problem solving approaches. Instead of inviting speakers for one large lecture we now invite them to be Resident Scholars for two-three days and develop a range of additional smaller public engagements. Science and engineering topics must be relevant - placed in the broader Science, Technology and Society framework. We avoid ``gee-whiz'' in favor of what stimulates reflection on who we are, where we came from, and our role in the universe. I will briefly review how we have survived and thrived and, finally, what I see as future trends and opportunities.

76 FR 50252 - Gray Portland Cement and Cement Clinker From Japan; Scheduling of an Expedited Five-Year Review...

Science.gov (United States)

2011-08-12

... INTERNATIONAL TRADE COMMISSION [Investigation No. 731-TA-461 (Third Review)] Gray Portland Cement and Cement Clinker From Japan; Scheduling of an Expedited Five-Year Review Concerning the Antidumping Duty Order on Gray Portland Cement and Cement Clinker From Japan AGENCY: United States International...

Oregon Trust Agreement Planning Project : Potential Mitigations to the Impacts on Oregon Wildlife Resources Associated with Relevant Mainstem Columbia River and Willamette River Hydroelectric Projects.

Energy Technology Data Exchange (ETDEWEB)

United States. Bonneville Power Administration.

1993-10-01

A coalition of the Oregon wildlife agencies and tribes (the Oregon Wildlife Mitigation Coalition) have forged a cooperative effort to promote wildlife mitigation from losses to Oregon wildlife resources associated with the four mainstream Columbia River and the eight Willamette River Basin hydroelectric projects. This coalition formed a Joint Advisory Committee, made up of technical representatives from all of the tribes and agencies, to develop this report. The goal was to create a list of potential mitigation opportunities by priority, and to attempt to determine the costs of mitigating the wildlife losses. The information and analysis was completed for all projects in Oregon, but was gathered separately for the Lower Columbia and Willamette Basin projects. The coalition developed a procedure to gather information on potential mitigation projects and opportunities. All tribes, agencies and interested parties were contacted in an attempt to evaluate all proposed or potential mitigation. A database was developed and minimum criteria were established for opportunities to be considered. These criteria included the location of the mitigation site within a defined area, as well as other criteria established by the Northwest Power Planning Council. Costs were established for general habitats within the mitigation area, based on estimates from certified appraisers. An analysis of the cost effectiveness of various types of mitigation projects was completed. Estimates of operation and maintenance costs were also developed. The report outlines strategies for gathering mitigation potentials, evaluating them, determining their costs, and attempting to move towards their implementation.

Ettringite and C-S-H Portland cement phases for waste ion immobilization: A review

International Nuclear Information System (INIS)

Gougar, M.L.D.; Scheetz, B.E.; Roy, D.M.

1996-01-01

The formation, structure and chemistry of the ettringite and C-S-H phases of Portland cement have been reviewed as they relate to waste ion immobilization. The purpose of this review was to investigate the use of Portland cement as a host for priority metallic pollutants as identified by the Environmental Protection Agency and as a host for radioactive waste ions as identified in 40 CFR 191. Ettringite acts as host to a number of these ions in both the columnar and channel sections of the crystal structure. Substitutions have been made at the calcium, aluminum, hydroxide and sulfate sites. C-S-H also hosts a number of the waste species in both ionic and salt form. Immobilization mechanisms for C-S-H include sorption, phase mixing and substitution. The following ions have not apparently been reported as specifically immobilized by one of these phases: Ag, Am, Np, Pu, Ra, Tc, Th and Sn; however, some of these ions are immobilized by Portland cement

Oregon Pupil Transportation Manual. Revised Regulations and Responsibilities.

Science.gov (United States)

Oregon State Dept. of Education, Salem.

Designed for use by Oregon school bus drivers and administrators, this manual answers common questions about school bus transportation in Oregon, including those about the laws governing pupil transportation, the regulations governing pupil transportation administration, and the laws on school bus operation. A chapter of advisory materials covers…

Some lessons in artificial regeneration from southwestern Oregon.

Science.gov (United States)

William I. Stein

1955-01-01

Natural reproduction has often proved undependable for restocking cutovers and burns in the mixed-conifer forest types of southwestern Oregon. These types, covering 6,000 square miles of productive forest land in the five southwestern Oregon counties, are composed of many species--principally Douglas fir, Pseudotsuga menziesii (Mirb.) Franco;...

2012 Oregon Lidar Consortium (OLC) Lidar DEM: Keno (OR)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Watershed Sciences, Inc. (WSI) collected Light Detection and Ranging (LiDAR) data of the Oregon Keno Study Area for the Oregon Department of Geology and Mineral...

Oregon wildlife planning coordination project: Annual report, October 1, 1998 to September 30, 1999

International Nuclear Information System (INIS)

Barnes, S.P.

1999-01-01

The intent of the Oregon Wildlife Planning Coordination project is to fund Oregon Department of Fish and Wildlife (ODFW) staff to facilitate wildlife mitigation coordination and planning between Oregon wildlife managers. The primary goal of ODFW wildlife mitigation planning/coordination staff is to foster, facilitate, and manage a statewide cooperative wildlife mitigation planning and implementation effort between the Oregon wildlife managers (the Oregon Wildlife Coalition or OWC) to mitigate for wildlife losses in Oregon caused by the development and operation of the hydropower system

Una nota sobre los Hormigones de Cemento Portland (HCP y Hormigones de Cemento Portland con Adiciones (HCPA

Directory of Open Access Journals (Sweden)

Talero Morales, Rafael

1993-09-01

Full Text Available El hombre contemporáneo ha dividido el proceso evolutivo de la humanidad en macroperíodos de tiempo relacionados con avances significativos obtenidos en el campo de los materiales. Así se define la edad de piedra, bronce, hierro, cobre, etc. Y siguiendo esta tendencia, probablemente las generaciones futuras podrán hablar de esta época como la "edad del hormigón" y mostrar los monumentales vestigios que, en su mayor parte, se han construido con hormigón de cemento portland.

2009 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Willamette Valley

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Oregon Department of Geology & Mineral Industries (DOGAMI) contracted with Watershed Sciences, Inc. to collect high resolution topographic LiDAR data for...

Properties of Portland-Composite Cements with metakaolin: Commercial and manufactured by Thermal Activation of Serbian Kaolin Clay

Directory of Open Access Journals (Sweden)

Mitrovic A.

2012-09-01

Full Text Available Portland-composite cements (CEM II were prepared with addition of 5 to 35% of metakaolin (MK, manufactured by thermal activation/calcination of Serbian kaolin clay, and commercial matakaolin (CMK. Performance of the composite cements was evaluated, through the setting time (initial and final, compressive strengths (for ages 2, 7, 28, 90 and 180 days and soundness, and compared with control cement (Portland cement – CEM I. Setting time (initial and final is accelerated in Portlandcomposite cements, for both metakaolins used. The acceleration is higher in cement with addition of commercial metakaolin. Lower compressive strength is obtained after 2 days of curing for all Portland-composite cements in comparison with control cement, since pozzolanic reaction still did not show its effect. After 7 days, pozzolanic reaction show its effect, manifested as compressive strength increase of Portland-composite cements with addition of up to 35% of CMK, and 25% in the case of cements with MK. After 28 days compressive strength was higher than that for control cement for cements prepared with addition of CMK, and with addition of up to 25% MK. After 90 days increased compressive strength was noticed with addition of 10 - 20% of CMK, and with 10 and 15% of MK, while after 180 days addition of both metakaolins influences compressive strength decrease. The results of the soundness, 0.5 mm for CEM I, and 1.0 mm in most Portland-composite cements indicate soundness increase with addition of metakaolins. Generally, better performance of Portland-composite cements was obtained with addition of commercial metakaolin, which may be attributed to the differences in the pozzolanic activity of the applied metakaolins, 20.5 MPa and 14.9 MPa for CMK and MK, respectively. By our previous findings pozzolanic activity of the thermally activated clay may be increased by subsequent milling of the metakaolin manufactured by thermal activation process.

A numerical investigation into the performance of the soil nail wall and pile foundation at the Swift Delta I-5 Interchange.

Science.gov (United States)

1993-12-01

Finite Difference Methods (FDM) and Finite Element Methods (FEM) studies are reported studying the soil nail wall construction at the Swift Delta I-5 Interchange bridge reconstruction in North Portland, Oregon. Five layers of soil nails were installe...

Experimental and modeling study of Portland cement paste degradation in boric acid

International Nuclear Information System (INIS)

Benakli, A.; Chomat, L.; Le Bescop, P.; Wall, J.

2015-01-01

In the framework of Spent Fuel Pools (SFP) lifetime studies, an investigation of the Portland cement degradation in boric acid has been requested by the Electric Power Research Institute. The main goal of this study is to identify the physico-chemical degradation mechanisms involved in boric acid media. Both experimental and modeling approaches are considered. Concerning degradation experiments, sample of cement paste are immersed during three and nine months in a boric acid solution at 2400 ppm that is periodically renewed. Boric acid concentration has been chosen to be representative of SFP solution. Results will be confronted with reactive transport numerical calculations performed by the reactive transport code HYTEC associated with a dedicated extended database called Thermoddem. The analysis of degradation solution revealed a main ions release mechanism driven by diffusion especially for calcium, nitrate, sodium and sulfate. Leaching behavior of magnesium seems to be more complex. Decalcification is the major degradation process involved, even if a non-negligible contribution of further cations (Mg 2+ , Na + ) and anions (SO 4 2- ) has been noticed. Analysis of degradation soution also revealed that kinetic of Portland cement paste degradation in boric acid is higher than in pure water, regarding the degraded depths measured and calcium leaching rate. This observation has been confirmed by solid characterization. Microstructure analysis of degraded Portland cement paste showed a global porosity increase in the degraded zone that might be mainly attributed to Portlandite dissolution. An Ettringite reprecipitation in the degraded zone has been suspected but could also be Ettringite-like phases containing boron. The analysis techniques used did not allow us to differentiate it, and no others specific mineral phases containing boron has been identified. Profile pattern by XRD analysis allowed us to identify four zones composing the degraded Portland cement paste

Waste-form development for conversion to portland cement at Los Alamos National Laboratory (LANL) Technical Area 55 (TA-55)

International Nuclear Information System (INIS)

Veazey, G.W.; Schake, A.R.; Shalek, P.D.; Romero, D.A.; Smith, C.A.

1996-10-01

The process used at TA-55 to cement transuranic (TRU) waste has experienced several problems with the gypsum-based cement currently being used. Specifically, the waste form could not reliably pass the Waste Isolation Pilot Plant (WIPP) prohibition for free liquid and the Environmental Protection Agency (EPA)-Toxicity Characteristic Leaching Procedure (TCLP) standard for chromium. This report describes the project to develop a portland cement-based waste form that ensures compliance to these standards, as well as other performance standards consisting of homogeneous mixing, moderate hydration temperature, timely initial set, and structural durability. Testing was conducted using the two most common waste streams requiring cementation as of February 1994, lean residue (LR)- and oxalate filtrate (OX)-based evaporator bottoms (EV). A formulation with a pH of 10.3 to 12.1 and a minimum cement-to-liquid (C/L) ratio of 0.80 kg/l for OX-based EV and 0.94 kg/L for LR-based EV was found to pass the performance standards chosen for this project. The implementation of the portland process should result in a yearly cost savings for raw materials of approximately $27,000 over the gypsum process

Use of red mud as addition for portland cement mortars

International Nuclear Information System (INIS)

Ribeiro, D.V.; Morelli, M.R.

2011-01-01

The aim of the present research work was to investigate the possibility of adding red mud, an alkaline leaching waste that is obtained from bauxite during the Bayer process for alumina production, in the raw meal of Portland cement mortars. The red mud is classified as dangerous, according to NBR 10004/2004, and world while generation reached over 117 million tons/year. This huge production requires high consuming products to be used as incorporation matrix and we studied the influence of red mud addition on the characteristics of cement mortars and concrete. In this paper the properties of Portland cement mortars incorporating high amounts of red mud was evaluated: pH variation, fresh (setting time, workability or normal consistency and water retention), and hardened state (mechanical strength, capillary water absorption, density and apparent porosity). Results seem promising for red mud additions up to 20 wt%. (author)

Study of irradiation damage by fast neutrons in samples of Portland cement

International Nuclear Information System (INIS)

Lucki, G.; Rosa Junior, A.A.

1984-01-01

The effect of neutron irradiation in samples of Portland cement was evaluated, using the resonance frequency method and pulse velocity of ultra-sound techniques. The samples were divided in three groups: 1) monitoring samples; 2) samples submitted to gamma heating; 3) Irradiated samples. In the sample preparation, it was used the Portland Santa Rita CP 320 cement, and water-cement rate of 0.40 l/Kg. The irradiation was done in the research reactor IEA-R1, at IPEN - CNEN/SP, with an integrated flux of 7.2 x 10 18 n/cm 2 (E approx. 1 MeV). Some damage were detected, due to the neutron flux, and by the thermal effect of gamma heating. (E.G.) [pt

Plugs or flood-makers? the unstable landslide dams of eastern Oregon

Science.gov (United States)

Safran, Elizabeth B.; O'Connor, Jim E.; Ely, Lisa L.; House, P. Kyle; Grant, Gordon E.; Harrity, Kelsey; Croall, Kelsey; Jones, Emily

2015-01-01

Landslides into valley bottoms can affect longitudinal profiles of rivers, thereby influencing landscape evolution through base-level changes. Large landslides can hinder river incision by temporarily damming rivers, but catastrophic failure of landslide dams may generate large floods that could promote incision. Dam stability therefore strongly modulates the effects of landslide dams and might be expected to vary among geologic settings. Here, we investigate the morphometry, stability, and effects on adjacent channel profiles of 17 former and current landslide dams in eastern Oregon. Data on landslide dam dimensions, former impoundment size, and longitudinal profile form were obtained from digital elevation data constrained by field observations and aerial imagery; while evidence for catastrophic dam breaching was assessed in the field. The dry, primarily extensional terrain of low-gradient volcanic tablelands and basins contrasts with the tectonically active, mountainous landscapes more commonly associated with large landslides. All but one of the eastern Oregon landslide dams are ancient (likely of order 103 to 104 years old), and all but one has been breached. The portions of the Oregon landslide dams blocking channels are small relative to the area of their source landslide complexes (0.4–33.6 km2). The multipronged landslides in eastern Oregon produce marginally smaller volume dams but affect much larger channels and impound more water than do landslide dams in mountainous settings. As a result, at least 14 of the 17 (82%) large landslide dams in our study area appear to have failed cataclysmically, producing large downstream floods now marked by boulder outwash, compared to a 40–70% failure rate for landslide dams in steep mountain environments. Morphometric indices of landslide dam stability calibrated in other environments were applied to the Oregon dams. Threshold values of the Blockage and Dimensionless Blockage Indices calibrated to worldwide

2013 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar DEM: Scappoose

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI collected Light Detection and Ranging (LiDAR) data for the Oregon LiDAR Consortium (OLC) Scappoose study area. The Scappoose project area encompasses...

Extraboard performance : TriMet case study.

Science.gov (United States)

2012-02-01

This paper examines extraboard operations and management at TriMet, the transit provider for the Portland Oregon metropolitan area. The : extraboard consists of a pool of operators who fill open work resulting from absences and other causes. The pape...

Ecological indices of manufacture of Portland cement clinker and production of the dolomite clinker

Directory of Open Access Journals (Sweden)

Vinnichenko Varvara

2017-01-01

Full Text Available It is shown that the production of dolomite clinker in comparison with that of Portland cement is environmentally appropriate. When calcining dolomite for cementitious binder, the pollution of the atmosphere by carbon dioxide is reduced due to its isolation during decarbonization reactions of calcium carbonates. Reducing fuel consumption for clinker burning provides less carbon dioxide emissions from combustion products. Reducing the firing temperature creates obstacles to the formation of nitrogen oxides. The production of binders from dolomite in comparison with the production of Portland cement helps to protect the environment from contamination

Portland Public Schools Project Chrysalis: Year 2 Evaluation Report.

Science.gov (United States)

Mitchell, Stephanie J.; Gabriel, Roy M.; Hahn, Karen J.; Laws, Katherine E.

In 1994, the Chrysalis Project in Portland Public Schools received funding to prevent or delay the onset of substance abuse among a special target population: high-risk, female adolescents with a history of childhood abuse. Findings from the evaluation of the project's second year of providing assistance to these students are reported here. During…

Language modeling for what-with-where on GOOG-411

CSIR Research Space (South Africa)

Van Heerden, C

2009-09-01

Full Text Available . For example, consider the query “looking for restaurants in Portland Oregon.” A business annotator identifies “restaurants” as a business/category, while the location annotator identifies “portland Oregon” as a city-state. This separation enables both task...-specific data selection (location and business), and task- specific text normalization. The output of this second step is used to build the business and location language models described in Section 3. 3. Language Modeling Alternatives In this section we...

78 FR 20073 - Adequacy of Oregon's Municipal Solid Waste Landfill Permit Program

Science.gov (United States)

2013-04-03

...] Adequacy of Oregon's Municipal Solid Waste Landfill Permit Program AGENCY: Environmental Protection Agency... Oregon's approved Municipal Solid Waste Landfill Program. On March 22, 2004, EPA issued final regulations... waste landfills by approved states. On June 14, 2012, Oregon submitted an application to EPA Region 10...

Using an epiphytic moss to identify previously unknown sources of atmospheric cadmium pollution

Energy Technology Data Exchange (ETDEWEB)

Donovan, Geoffrey H., E-mail: gdonovan@fs.fed.us [USDA Forest Service, PNW Research Station, 620 SW Main, Suite 400, Portland, OR 97205 (United States); Jovan, Sarah E., E-mail: sjovan@fs.fed.us [USDA Forest Service, PNW Research Station, 620 SW Main, Suite 400, Portland, OR 97205 (United States); Gatziolis, Demetrios, E-mail: dgatziolis@fs.fed.us [USDA Forest Service, PNW Research Station, 620 SW Main, Suite 400, Portland, OR 97205 (United States); Burstyn, Igor, E-mail: igor.burstyn@drexel.edu [Dornsife School of Public Health, Drexel University, Nesbitt Hall, 3215 Market St, Philadelphia, PA 19104 (United States); Michael, Yvonne L., E-mail: ylm23@drexel.edu [Dornsife School of Public Health, Drexel University, Nesbitt Hall, 3215 Market St, Philadelphia, PA 19104 (United States); Amacher, Michael C., E-mail: mcamacher1@outlook.com [USDA Forest Service, Logan Forest Sciences Laboratory, 860 North 1200 East, Logan, UT 84321 (United States); Monleon, Vicente J., E-mail: vjmonleon@fs.fed.us [USDA Forest Service, PNW Research Station, 3200 SW Jefferson Way, Corvallis, OR 97331 (United States)

2016-07-15

Urban networks of air-quality monitors are often too widely spaced to identify sources of air pollutants, especially if they do not disperse far from emission sources. The objectives of this study were to test the use of moss bio-indicators to develop a fine-scale map of atmospherically-derived cadmium and to identify the sources of cadmium in a complex urban setting. We collected 346 samples of the moss Orthotrichum lyellii from deciduous trees in December, 2013 using a modified randomized grid-based sampling strategy across Portland, Oregon. We estimated a spatial linear model of moss cadmium levels and predicted cadmium on a 50 m grid across the city. Cadmium levels in moss were positively correlated with proximity to two stained-glass manufacturers, proximity to the Oregon–Washington border, and percent industrial land in a 500 m buffer, and negatively correlated with percent residential land in a 500 m buffer. The maps showed very high concentrations of cadmium around the two stained-glass manufacturers, neither of which were known to environmental regulators as cadmium emitters. In addition, in response to our findings, the Oregon Department of Environmental Quality placed an instrumental monitor 120 m from the larger stained-glass manufacturer in October, 2015. The monthly average atmospheric cadmium concentration was 29.4 ng/m{sup 3}, which is 49 times higher than Oregon's benchmark of 0.6 ng/m{sup 3}, and high enough to pose a health risk from even short-term exposure. Both stained-glass manufacturers voluntarily stopped using cadmium after the monitoring results were made public, and the monthly average cadmium levels precipitously dropped to 1.1 ng/m{sup 3} for stained-glass manufacturer #1 and 0.67 ng/m{sup 3} for stained-glass manufacturer #2. - Highlights: • Bio-indicators are a valid method for measuring atmospheric pollutants • We used moss to map atmospheric cadmium in Portland, Oregon • Using a spatial linear model, we identified two

2015 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Upper Umpqua

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — QSI has completed the acquisition and processing of Light Detection and Ranging (LiDAR) data describing the Oregon LiDAR Consortium's (OLC) Umpqua Study Area. The...

2014 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Four Rivers

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI has completed the acquisition and processing of Light Detection and Ranging (LiDAR) data and Four-Band Radiometric Image Enhanced Survey (FRIES) of the Oregon...

2012 Oregon Department of Geology and Mineral Industries (DOGAMI) Lidar: Rogue River Oregon

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI has collected Light Detection and Ranging (LiDAR) data of the Rogue River Study Area for the Oregon Department of Geology and Mineral Industries (DOGAMI),...

Genetic characteristics of red foxes In northeastern Oregon

Science.gov (United States)

Gregory A Green; Benjamin N Sacks; Leonard J Erickson; Keith B Aubry

2017-01-01

The Rocky Mountain Red Fox (Vulpes vulpes macroura), once common in the Blue Mountains ecoregion of northeastern Oregon, was considered rare in eastern Oregon by the 1930s and thought to be extirpated by the 1960s, when putatively new Red Fox populations began to appear. Although the new foxes were long presumed to be nonnative (originating from...

75 FR 14567 - Export Trade Certificate of Review

Science.gov (United States)

2010-03-26

... (Netherlands)).'' Make corrections to the following Members' listings: ``Itochu International Inc., New York, New York (a subsidiary of Itochu Corporation (Japan))'' has been amended to read ``Itochu International Inc., Portland, Oregon (a subsidiary of Itochu Corporation (Japan))''; and ``Nobel Logistics USA...

Remediation System Evaluation, Northwest Pipe and Casing Site

Science.gov (United States)

The Northwest Pipe and Casing Site is located in Clackamas, Oregon, approximately 20 miles southeastof Portland. The site consists of approximately 53 acres, and has historically been divided into two parcels(Parcel A to the north and Parcel B to the..

Influencia del yeso sobre la velocidad de hidratación del cemento portland

Directory of Open Access Journals (Sweden)

Yamaguchi, G.

1961-12-01

Full Text Available Not availablePara esclarecer la Influencia del yeso sobre el fraguado y endurecimiento del cemento, los autores estudiaron el grado de hidratación de los cuatro principales minerales del clínker de cemento Portland y el efecto del yeso sobre ellas. Haciendo uso del análisis cuantitativo de rayos X, se determinó la porción no hidratada. Simultáneamente, se determinaron los tiempos de fraguado y las resistencias. Los ensayos se llevaron a cabo sobre tres clínkeres sintéticos de diferentes composiciones y sobre dos clínkeres de cemento Portland comerciales.

Thermodynamic modelling of the effect of temperature on the hydration and porosity of Portland cement

International Nuclear Information System (INIS)

Lothenbach, Barbara; Matschei, Thomas; Moeschner, Goeril; Glasser, Fred P.

2008-01-01

The composition of the phase assemblage and the pore solution of Portland cements hydrated between 0 and 60 deg. C were modelled as a function of time and temperature. The results of thermodynamic modelling showed a good agreement with the experimental data gained at 5, 20, and 50 deg. C. At 5 and at 20 deg. C, a similar phase assemblage was calculated to be present, while at approximately 50 deg. C, thermodynamic calculations predicted the conversion of ettringite and monocarbonate to monosulphate. Modelling showed that in Portland cements which have an Al 2 O 3 /SO 3 ratio of > 1.3 (bulk weight), above 50 deg. C monosulphate and monocarbonate are present. In Portland cements which contain less Al (Al 2 O 3 /SO 3 < 1.3), above 50 deg. C monosulphate and small amounts of ettringite are expected to persist. A good correlation between calculated porosity and measured compressive strength was observed

Receipt of Preventive Services After Oregon's Randomized Medicaid Experiment.

Science.gov (United States)

Marino, Miguel; Bailey, Steffani R; Gold, Rachel; Hoopes, Megan J; O'Malley, Jean P; Huguet, Nathalie; Heintzman, John; Gallia, Charles; McConnell, K John; DeVoe, Jennifer E

2016-02-01

It is predicted that gaining health insurance via the Affordable Care Act will result in increased rates of preventive health services receipt in the U.S., primarily based on self-reported findings from previous health insurance expansion studies. This study examined the long-term (36-month) impact of Oregon's 2008 randomized Medicaid expansion ("Oregon Experiment") on receipt of 12 preventive care services in community health centers using electronic health record data. Demographic data from adult (aged 19-64 years) Oregon Experiment participants were probabilistically matched to electronic health record data from 49 Oregon community health centers within the OCHIN community health information network (N=10,643). Intent-to-treat analyses compared receipt of preventive services over a 36-month (2008-2011) period among those randomly assigned to apply for Medicaid versus not assigned, and instrumental variable analyses estimated the effect of actually gaining Medicaid coverage on preventive services receipt (data collected in 2012-2014; analysis performed in 2014-2015). Intent-to-treat analyses revealed statistically significant differences between patients randomly assigned to apply for Medicaid (versus not assigned) for 8 of 12 assessed preventive services. In intent-to-treat analyses, Medicaid coverage significantly increased the odds of receipt of most preventive services (ORs ranging from 1.04 [95% CI=1.02, 1.06] for smoking assessment to 1.27 [95% CI=1.02, 1.57] for mammography). Rates of preventive services receipt will likely increase as community health center patients gain insurance through Affordable Care Act expansions. Continued effort is needed to increase health insurance coverage in an effort to decrease health disparities in vulnerable populations. Copyright © 2016 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Debating death: religion, politics, and the Oregon Death With Dignity Act.

Science.gov (United States)

Purvis, Taylor E

2012-06-01

In 1994, Oregon passed the Oregon Death With Dignity Act, becoming the first state in the nation to allow physician-assisted suicide (PAS). This paper compares the public discussion that occurred in 1994 and during the Act's implementation in 1997 and examines these debates in relation to health care reform under the Obama administration. I argue that the 1994 and 1997 Oregon PAS campaigns and the ensuing public debate represent the culmination of a growing lack of deference to medical authority, concerns with the doctor-patient relationship, and a desire for increased patient autonomy over decisions during death. The public debate over PAS in Oregon underscored the conflicts among competing religious, political, and personal interests. More visible and widespread than any other American debate on PAS, the conflict in Oregon marked the beginning of the now nationwide problem of determining if and when a terminally ill person can choose to die.

Floating Offshore Wind in Oregon: Potential for Jobs and Economic Impacts in Oregon Coastal Counties from Two Future Scenarios

Energy Technology Data Exchange (ETDEWEB)

Jimenez, Tony [National Renewable Energy Lab. (NREL), Golden, CO (United States); Keyser, David [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tegen, Suzanne [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-07-01

This analysis examines the employment and potential economic impacts of large-scale deployment of offshore wind technology off the coast of Oregon. This analysis examines impacts within the seven Oregon coastal counties: Clatsop, Tillamook, Lincoln, Lane, Douglas, Coos, and Curry. The impacts highlighted here can be used in county, state, and regional planning discussions and can be scaled to get a general sense of the economic development opportunities associated with other deployment scenarios.

2015 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Big Windy

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Quantum Spatial collected Light Detection and Ranging (LiDAR) data for the Oregon LiDAR Consortium (OLC) Big Windy 2015 study area. This study area is located near...

2014 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Crooked Ochoco

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI, a Quantum Spatial company, has collected lidar data for the Oregon LiDAR Consortium (OLC) Crooked Ochoco study area. This study area is adjacent to the Ochoco...

2013 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Big Windy

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — In July of 2013, lightning strikes ignited three wildfires in southwest Oregon that became known as the Big Windy Complex. The fires were fully contained by the end...

STABILISASI TANAH LIAT SANGAT LUNAK DENGAN GARAM DAN PC (PORTLAND CEMENT

Directory of Open Access Journals (Sweden)

Tirta Djusman Arief

2006-01-01

Full Text Available Adding sodium chloride, as admixture, and Portland Cement, as stabilizer, to a very soft clay increase its plasticity index (PI, Californian Bearing Ratio (CBR, and Unconfined Compression Strength (UCS. This paper presents the results of testings done to very soft clay from Margomulyo, Surabaya. The results show a promising tendency. Anyhow a wider and comprehensive research is still needed to ensure the long-term effect of the soil stabilization. Abstract in Bahasa Indonesia : Penambahan garam (sodium chloride dan PC (Portland Cement meningkatkan PI (Plasticity Index, CBR (Californian Bearing Ratio, dan UCS (Unconfined Compression Strength dari tanah lempung sangat lunak. Dalam makalah ini disajikan hasil pengujian yang dilakukan terhadap lempung sangat lunak dari daerah Margomulyo, Surabaya. Hasilnya menunjukkan kecenderungan yang menggembirakan, namun penelitian yang luas dan komprehensif masih diperlukan untuk peningkatan stabilitas tanah dalam jangka panjang.

2008 Oregon Department of Geology and Mineral Industries (DOGAMI) Lidar: Lake Billy Chinook, Oregon

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Oregon Department of Geology & Mineral Industries (DOGAMI) contracted with Watershed Sciences, Inc. to collect high resolution topographic LiDAR data for...

Comparative evaluation of antimicrobial activity of three cements: new endodontic cement (NEC), mineral trioxide aggregate (MTA) and Portland.

Science.gov (United States)

Hasan Zarrabi, Mohammad; Javidi, Maryam; Naderinasab, Mahboube; Gharechahi, Maryam

2009-09-01

Using the agar diffusion method, we conducted an in vitro study to evaluate the antimicrobial activity of mineral trioxide aggregate (MTA), new endodontic cement (NEC) and Portland cement at different concentrations against five different microorganisms. A base layer was made using Muller-Hinton agar for Escherichia coli (ATCC 10538) and Candida (ATCC 10231). For Actinomyces viscosus (ATCC 15987), Enterococcus faecalis (ATCC 10541) and Streptococcus mutans (ATCC 25175) blood agar medium was used. Wells were formed by removing the agar, and the materials were placed in the well immediately after manipulation. The plates were kept at room temperature for 2 h for prediffusion, and then incubated at 37 degrees C for 72 h. The inhibition zones were then measured. The data were analyzed using ANOVA and the Tukey test to compare the differences among the three cements at different concentrations. The positive controls showed bacterial growth, while the negative controls showed no bacterial growth. All materials showed antimicrobial activity against the tested strains except for Enterococcus faecalis. NEC created larger inhibition zones than MTA and Portland cement. This difference was significant for Portland cement (P 0.05). Among the examined microorganisms, the largest inhibition zone was observed for Actinomyces group (P < 0.05). The antimicrobial activity of the materials increased with time and concentration (P < 0.05). It was concluded that NEC is a potent inhibitor of microorganism growth.

Ex vivo assessment of genotoxicity and cytotoxicity in murine fibroblasts exposed to white MTA or white Portland cement with 15% bismuth oxide.

Science.gov (United States)

Zeferino, E G; Bueno, C E S; Oyama, L M; Ribeiro, D A

2010-10-01

To evaluate whether white mineral trioxide aggregate (MTA) or white Portland cement with 15% bismuth oxide were able to induce genetic damage and cellular death ex vivo. Aliquots of 1 × 10(4) murine fibroblasts were incubated at 37 °C for 3 h with MTA (white) or white Portland cement with 15% bismuth oxide, at final concentrations ranging from 10 to 1000 μg mL(-1) individually. Data of three independent repeats from the comet assay and the trypan blue exclusion test were assessed by the one-way anova followed by Tukey's test. Mineral trioxide aggregate or Portland cement containing bismuth oxide did not produce genotoxic effects with respect to the single-cell gel (comet) assay data for all concentrations evaluated. Furthermore, no cytotoxicity was observed for MTA or Portland cement. White MTA or white Portland cement containing 15% bismuth oxide were not genotoxic and cytotoxic. © 2010 International Endodontic Journal.

EnviroAtlas - Portland, ME - Meter-Scale Urban Land Cover (MULC) Data (2010)

Data.gov (United States)

U.S. Environmental Protection Agency — The EnviroAtlas Portland, ME Meter-Scale Urban Land Cover (MULC) data was generated from USDA NAIP (National Agricultural Imagery Program) four band (red, green,...

Go West: Imagining the Oregon Trail. [Lesson Plan].

Science.gov (United States)

National Endowment for the Humanities (NFAH), Washington, DC.

In this lesson plan, students in grades 3-5 compare imagined travel experiences of their own with the actual experiences of 19th-century pioneers on the Oregon Trail. After the 4 lessons students will have: (1) learned about the pioneer experience on the Oregon Trail; (2) compared and contrasted modern-day travel experiences with those of the 19th…

Rat subcutaneous tissue response to MTA Fillapex® and Portland cement.

Science.gov (United States)

Marques, Nádia Carolina Teixeira; Lourenço Neto, Natalino; Fernandes, Ana Paula; Rodini, Camila de Oliveira; Duarte, Marco Antônio Hungaro; Oliveira, Thais Marchini

2013-01-01

The aim of this study was to evaluate the response of rat subcutaneous tissue to MTA Fillapex® (Angelus), an experimental root canal filling material based on Portland cement and propylene glycol (PCPG), and a zinc oxide, eugenol and iodoform (ZOEI) paste. These materials were placed in polyethylene tubes and implanted into the dorsal connective tissue of Wistar rats for 7 and 15 days. The specimens were stained with hematoxylin and eosin, and evaluated regarding inflammatory reaction parameters by optical microscopy. The intensity of inflammatory response against the sealers was analyzed by two blinded and previously calibrated examiners for all experimental periods (kappa=0.96). The histological evaluation showed that all materials caused a moderate inflammatory reaction at 7 days, which subsided with time. A greater inflammatory reaction was observed at 7 days in the tubes filled with ZOEI paste. Tubes filled with MTA Fillapex presented some giant cells, macrophages and lymphocytes after 7 days. At 15 days, the presence of fibroblasts and collagen fibers was observed indicating normal tissue healing. The tubes filled with PCPG showed similar results to those observed in MTA Fillapex. At 15 days, the inflammatory reaction was almost absent at the tissue, with several collagen fibers indicating normal tissue healing. Data were analyzed by the nonparametric Kruskal-Wallis test (α=0.05). Statistically significant difference (p0.05). MTA Fillapex and Portland cement added with propylene glycol had greater tissue compatibility than the PCPG paste.

INFLUENCE OF BARIUM OXIDE ADDITIONS ON PORTLAND CLINKER

Directory of Open Access Journals (Sweden)

Anezka Zezulova

2016-12-01

Full Text Available Nowadays, nuclear power plants are widespread around the world and research is of great interest. Together with nuclear research, shielding of different types of radiation is an important current topic of research aiming at their safety. Portland cement has been an elementary building material for centuries. Since barium is very efficient in shielding different types of radiation, it can be assumed that the radiation shielding capability of cement can be improved by incorporation of barium. This work deals with the influence of barium oxide, added in the form of barium carbonate and sulphate, on the formation and properties of Portland clinker. The structure of burnt clinkers and the ratio of clinker phases were studied by polarizing microscopy and by X-ray diffraction. With increasing barium content, the alite-belite ratio decreases and the content of free lime gradually increases. Moreover, sulphates induce the growth of alite crystals. The ability of barium to be a part of the clinker minerals was observed by scanning electron microscopy. Belite and clinker melt contain the highest amount of barium, but aggregates of barium oxide are formed in the clinker melt. Furthermore, the rate of alite crystallization was studied under isothermal conditions.

Response of Stream Chemistry During Base Flow to Gradients of Urbanization in Selected Locations Across the Conterminous United States, 2002-04

Science.gov (United States)

Sprague, Lori A.; Harned, Douglas A.; Hall, David W.; Nowell, Lisa H.; Bauch, Nancy J.; Richards, Kevin D.

2007-01-01

During 2002-2004, the U.S. Geological Survey's National Water-Quality Assessment Program conducted a study to determine the effects of urbanization on stream water quality and aquatic communities in six environmentally heterogeneous areas of the conterminous United States--Atlanta, Georgia; Raleigh-Durham, North Carolina; Milwaukee-Green Bay, Wisconsin; Dallas-Fort Worth, Texas; Denver, Colorado; and Portland, Oregon. This report compares and contrasts the response of stream chemistry during base flow to urbanization in different environmental settings and examines the relation between the exceedance of water-quality benchmarks and the level of urbanization in these areas. Chemical characteristics studied included concentrations of nutrients, dissolved pesticides, suspended sediment, sulfate, and chloride in base flow. In three study areas where the background land cover in minimally urbanized basins was predominantly forested (Atlanta, Raleigh-Durham, and Portland), urban development was associated with increased concentrations of nitrogen and total herbicides in streams. In Portland, there was evidence of mixed agricultural and urban influences at sites with 20 to 50 percent urban land cover. In two study areas where agriculture was the predominant background land cover (Milwaukee-Green Bay and Dallas-Fort Worth), concentrations of nitrogen and herbicides were flat or decreasing as urbanization increased. In Denver, which had predominantly shrub/grass as background land cover, nitrogen concentrations were only weakly related to urbanization, and total herbicide concentrations did not show any clear pattern relative to land cover - perhaps because of extensive water management in the study area. In contrast, total insecticide concentrations increased with increasing urbanization in all six study areas, likely due to high use of insecticides in urban applications and, for some study areas, the proximity of urban land cover to the sampling sites. Phosphorus

DOE Center of Excellence in Medical Laser Applications. Final report, December 1, 1994--November 30, 1997

Energy Technology Data Exchange (ETDEWEB)

Jacques, S.L.

1998-01-01

An engineering network of collaborating medical laser laboratories are developing laser and optical technologies for medical diagnosis and therapy and are translating the engineering into medical centers in Portland OR, Houston TX, and Galveston TX. The Center includes the University of Texas M.D. Anderson Cancer Center, the University of Texas-Austin, Texas A and M University, Rice University, the University Texas Medical Branch-Galveston, Oregon Medical Laser Center (Providence St. Vincent Medical Center, Oregon Health Sciences University, and Oregon Graduate Institute, Portland, OR), and the University of Oregon. Diagnostics include reflectance, fluorescence, Raman IR, laser photoacoustics, optical coherence tomography, and several new video techniques for spectroscopy and imaging. Therapies include photocoagulation therapy, laser welding, pulsed laser ablation, and light-activated chemotherapy of cancer (photodynamic therapy, or PDT). Medical applications reaching the clinic include optical monitoring of hyperbilirubinemia in newborns, fluorescence detection of cervical dysplasia, laser thrombolysis of blood clots in heart attack and brain stroke, photothermal coagulant of benign prostate hyperplasia, and PDT for both veterinary and human cancer. New technologies include laser optoacoustic imaging of breast tumors and hemorrhage in head trauma and brain stroke, quality control monitoring of dosimetry during PDT for esophageal and lung cancer, polarization video reflectometry of skin cancer, laser welding of artificial tissue replacements, and feedback control of laser welding.

Virginia Tech's College Of Natural Resources Dedicates Cheatham Hall Expansion

OpenAIRE

Davis, Lynn

2003-01-01

Thanks to funding by private donors, Alyce Cheatham and her family of Portland, Oregon, Virginia Tech's College of Natural Resources will dedicate a much-needed, three-story addition to its current Cheatham Hall on Wednesday, March 19, at 2:30 p.m.

Resonance – Journal of Science Education | Indian Academy of ...

Indian Academy of Sciences (India)

David L Farrens1 Thomas P Sakmar2. Department of Biochemistry and Molecular Biology Oregon Health and Science University Portland OR 97239, USA. Head, Laboratory of Chemical Biology and Signal Transduction The Rockefeller University, 1230 York, Ave., New York, NY 10065, USA.

Summary of Research: Academic Departments 1990-1991

Science.gov (United States)

1991-10-01

of Systems Sciences, Portland, Oregon, 9 July 1990. CULHAM, Phyllis, Professor, " Plutarch on the Siege of Syracusc: The Primacy of Science over...ARTIGIANI, P. Robert, Professor, "Social Change: Technology," International Plutarch Society, Insights and Implications from Contemporary University of

76 FR 14386 - Environmental Management Site-Specific Advisory Board, Hanford

Science.gov (United States)

2011-03-16

...: Red Lion Hotel on the River, Jantzen Beach, 909 North Hayden Island Drive, Portland, Oregon 97217... Committee; Public Involvement Committee; and Budgets and Contracts Committee Potential Board Advice [cir] 2011-2013 Budget [cir] Regulatory document timelines/review [cir] Radioactive solid waste burial...

Demonstration of the Trauma Nurses Talk Tough seat belt diversion program in North Carolina.

Science.gov (United States)

2014-03-01

Trauma Nurses Talk Tough is a seat belt diversion program originally developed at the Legacy Emanuel Hospital in Portland, Oregon, in 1988. Attendance at the course is a condition for a one-time dismissal of a seat belt citation without fine or court...

The Influence of Emerging Leadership in Nursing: An Interview With Dr Casey Shillam.

Science.gov (United States)

Adams, Jeffrey M

2016-11-01

This department highlights emerging nursing leaders who have demonstrated leadership in advancing innovation and patient care in practice, policy, research, education, and theory. This interview profiles Casey Shillam, PhD, RN, associate dean for baccalaureate education, University of Portland School of Nursing, Oregon.

Hemoparasites in Oregon spotted frogs (Rana pretiosa) from central Oregon, USA.

Science.gov (United States)

Stenberg, Patricia L; Bowerman, William J

2008-04-01

Between 2001 and 2003, we screened blood smears of 156 Oregon spotted frogs (Rana pretiosa) from three populations in central Oregon for blood parasites. A Lankesterella sp. and a Trypanosoma sp. were detected in 31% and 35% of the frogs, respectively. Parasite loads were generally light, with Lankesterella sporozoites in 1-2% of erythrocytes, and extracellular trypanosomes were seen at rates of about one parasite per 200 fields of view at 1,000x. Little work has been published on hemoparasites of ranids in the western USA in the past 30 yr. Because of the recent taxonomic division of the Rana pretiosa complex, this may be the first published report of blood parasites for R. pretiosa sensu stricto. Both parasites reported here differed in morphologic features and morphometric comparisons from previous descriptions of anuran hemoparasites. Much work remains to sort out the taxonomy of hemoparasites among western USA ranids and to determine the ecological significance of these parasites; both tasks are important steps in understanding and managing these, and related, sensitive and threatened species.

Biological evaluation of a new pulp capping material developed from Portland cement.

Science.gov (United States)

Negm, Ahmed M; Hassanien, Ehab E; Abu-Seida, Ashraf M; Nagy, Mohamed M

2017-03-02

This study evaluates the biological properties of a new pulp capping material developed from Portland cement. This study was conducted on 48 teeth in 4 dogs (12 teeth/dog). The dogs were classified into two equal groups (n=24 teeth) according to the evaluation period including: group A (3 weeks) and group B (3 months). Each group was further subdivided into three equal subgroups (n=8 teeth) according to the capping material including: subgroup 1: mineral trioxide aggregate (MTA), subgroup2: Portland cement+10% calcium hydroxide+20% bismuth oxide (Port Cal) and subgroup 3: Portland cement+bismuth oxide. After general anesthesia, a class V buccal cavity was prepared coronal to the gingival margin. After pulp exposure and hemostasis,the capping materials and glass ionomer filling were placed on the exposure sites. All histopathological findings, inflammatory cell count and dentin bridge formation were recorded. Data were analyzed statistically. After 3 months, the histopathological picture of the pulp in subgroup 1 showed normal pulp, continuous odontoblastic layer and complete dentin bridge formation while subgroup 2 showed partial and complete dentin bridge over a normal and necrotic pulps. Subgroup 3 showed loss of normal architecture, areas of necrosis, complete, or incomplete dentin bridge formation, attached and detached pulp stones and fatty degeneration in group B. For group A, MTA subgroup showed the least number of inflammatory cell infiltrate followed by Port Cal subgroup. While subgroup 3 showed the highest number of inflammatory cell infiltrate. For group B, the mean inflammatory cell count increased with the three tested materials with no statistical difference. Regarding dentin bridge formation at group A, no significant differences was found between subgroups, while at group B, MTA subgroup exhibited significantly higher scores than other subgroups. In conclusion, addition of calcium hydroxide to Portland cement improves the dentin bridge formation

A comparative evaluation of ProRoot mineral trioxide aggregate and Portland cement as a pulpotomy medicament.

Science.gov (United States)

Bhagat, Dipti; Sunder, Ravi Kadur; Devendrappa, Shashikiran Nandihalli; Vanka, Amit; Choudaha, Nidhi

2016-01-01

Recently, some studies have compared mineral trioxide aggregate (MTA) with portland cement (PC), concluding that the principle ingredients of PC are similar to those of MTA. The purpose of the present study was to evaluate the biocompatibility of PC as a pulpotomy medicament. Thirty premolars that scheduled for extraction for therapeutic reasons were randomly assigned to two experimental groups: ProRoot MTA (PMTA) and PC. After isolation and pulp exposure, pulpotomy was carried out and pulps were dressed with PMTA and PC. After 6 months, the teeth were extracted and prepared for histological analysis based on Cox et al. criteria. The data were analyzed by Z-test of proportion with 1% of allowed error. No statistically significant difference was found between the two groups with respect to inflammatory response, soft tissue organization, and dentine bridge formation (P > 0.05). PC was associated with similar favorable biological response to pulpotomy treatment as PMTA. The findings of this study support the idea that PC can be considered a cheaper substitute to MTA.

2014 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar DEM: Four Rivers

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — WSI has completed the acquisition and processing of Light Detection and Ranging (LiDAR) data and Four-Band Radiometric Image Enhanced Survey (FRIES) of the Oregon...

Seasonal species composition of invertebrates in several Oregon streams.

Science.gov (United States)

Pamela E. Porter; William R. Meehan

1987-01-01

The invertebrate communities ofeight Oregon streams were sampled seasonally from 1974 to 1976. Benthic, drift, and two types of aerial-trap samples were collected. Occurrence and percentage composition are summarized by sample type, season, and geographic area (coastal, Cascade, central, and eastern Oregon). Within 276 families, 426 taxa were identified; the 20...

Development of the Portland cement slurries with diatomaceous earth to the oil industry; Desenvolvimento de pastas de cimento Portland com adicao de diatomita para a industria do petroleo

Energy Technology Data Exchange (ETDEWEB)

Brito, Roseane A; Melo, Dulce M.A.; Martinelli, Antonio E.; Simao, Cristina A.; Paiva, Maria D.M. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Melo, Marcus A.F. [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

2004-07-01

The class-G Portland cement has been used with success in oil well cementing. The material is usually shipped to the Northeast Brazil, because the only plant that manufactures class-G is located in Cantagalo/RJ. The present work investigates the influence of the partial substitution of Portland cement by diatomaceous earth, aiming at reducing the costs in oil well cementing, improving the slurry properties and using local raw material. The diatomaceous earth has pozzolanic properties and can be used as extenders of cement slurries. This properties added to the lower cost and availability of this material in Northeast Brazil, make the diatomaceous earth a candidate material to produce light cements, to well conditions in advanced phases of production. It were evaluated the rheological properties of the slurries (at 25 and 52 deg C), volume of free water, compressive strength after curing for 8, 24 and 48 h at 38 deg C, and consistometry tests. The results show that the diatomaceous earth maintain the viscosity values and gel force suitable for use in oil well cementing. No free water was observed in the formulations. It was also verified that the compressive strength of slurries hardened with diatomaceous earth is similar to those with only Portland cement and that the minimum compressive strength of 300 psi, after curing for 8 h was reached. The thickening time was longer than the average value and the application value. (author)

Production of portland cement using Moroccan oil shale and comparative study between conventional cement plant and cement plant using oil shale

International Nuclear Information System (INIS)

Doumbouya, M.; Kacemi, K.E.; Kitane, S.

2012-01-01

Like the use of coal ash from power plants as an addition to cement, oil shale are used for cement production on an industrial scale in Estonia, China, USA and Germany. Oil shale can be utilized in manufacturing the cement. In addition to the utilization of these by-products after combustion, it can also reduce the required temperature for the clinkering reactions during the production of Portland clinker. We performed a study on the Moroccan oil shale to maximize the use of oil shale ash in the manufacturing of Portland cement. We found that Moroccan oil shale ash can be used up to 30% with 70% Portland clinker without altering its principle properties. The corresponding temperature required to generate the required liquid for the clinkering reactions as well as the essential ingredients for clinker was found to be around 850 to 1000 deg. C. The operating temperatures for this optimized blend ratio were found to 1000 deg. C. The resulting Portland clinker from this ratio will need further testing in accordance with international standards for Portland cement to examine properties like strength and setting time. (author)

2016 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: McKenzie River

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Quantum Spatial collected Light Detection and Ranging (LiDAR) data for the Oregon LiDAR Consortium (OLC) McKenzie River study area. This study area is located near...

Final Rule: NESHAP for the Portland Cement Manufacturing Industry: Alternative Monitoring Method

Science.gov (United States)

EPA is extending its approval for the use of an alternative method to show compliance with hydrogen chloride (HCl) emissions limits in the National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing Industry

Utilizing Science to Ensure Safe Access to Cultural Resources on Public Lands: The Portland Native American Community and Traditional Gathering of Camas

Science.gov (United States)

Greene, C.

2017-12-01

Native Americans have been conducting and contributing to science for millenia. We have observed nature and passed on evidence-based Traditional Ecological Knowledge (TEK) from generation to generation. Prior to colonization, this knowledge enabled our people to live with ample nutritional resources. Our long-standing relationship to nature continues today in tribal, rural, and urban communities, yet access to cultural resources (traditional food and medicines) proves challenging due to modern land management practices. The Native American community and public land managers in Portland, Oregon are addressing this challenge through the restoration of cultural resources across the landscape. One focus in these efforts is the camas plant (Camssia quamash), which grows in wetland and prairie ecosystems. The harvested bulbs are traditionally pit roasted, converting the indigestible inulin into carbohydrates of high nutritional value. Access to local natural areas has been granted for Native American community members to gather camas, yet pesticide and herbicide application as land management practices have created uncertainty regarding the safety of ingesting the camas bulbs. The Native American community gathered camas bulbs in November 2015 for analysis, which resulted in glyphosate (pesticide) and triclopyr (herbicide). There are various factors which may influence the uptake of pesticide and herbicide residuals in camas which need further investigation, including pesticide/herbicide application details (date, location), preferential uptake of pesticide/herbicides in camas among the present plant community, the impact of pit roasting bulbs on residuals, and traditional land management practices like prescribed burning. Utilizing TEK and science to ensure safe access to cultural resources is paramount in preserving our cultures and enhancing the value of indigenous perspectives on land management practices and policies.

High-volume natural volcanic pozzolan and limestone powder as partial replacements for portland cement in self-compacting and sustainable concrete

KAUST Repository

Celik, Kemal; Jackson, Marie D.; Mancio, Mauricio; Meral, Cagla; Emwas, Abdul-Hamid M.; Mehta, P. Kumar; Monteiro, Paulo José Meleragno

2014-01-01

A laboratory study demonstrates that high volume, 45% by mass replacement of portland cement (OPC) with 30% finely-ground basaltic ash from Saudi Arabia (NP) and 15% limestone powder (LS) produces concrete with good workability, high 28-day compressive strength (39 MPa), excellent one year strength (57 MPa), and very high resistance to chloride penetration. Conventional OPC is produced by intergrinding 95% portland clinker and 5% gypsum, and its clinker factor (CF) thus equals 0.95. With 30% NP and 15% LS portland clinker replacement, the CF of the blended ternary PC equals 0.52 so that 48% CO2 emissions could be avoided, while enhancing strength development and durability in the resulting self-compacting concrete (SCC). Petrographic and scanning electron microscopy (SEM) investigations of the crushed NP and finely-ground NP in the concretes provide new insights into the heterogeneous fine-scale cementitious hydration products associated with basaltic ash-portland cement reactions. © 2013 Published by Elsevier Ltd.

Corbicula fluminea as a Bioaccumulation Indicator Species: A Case Study at the Columbia and Willamette Rivers

Science.gov (United States)

2009-06-01

Johnson and Norton 2005). Other studies ( Buske 2005; Kaltofen and Carpenter 2005) looked at radionuclide levels in clams along the 50-mile Hanford...resources from the Columbia River. Final Report. Portland, OR: US Fish and Wildlife Service, Oregon Fish and Wildlife Office. Buske , N. 2005

The applicability of a multitask boxing program using the BoxMaster ® for Parkinson’s disease

OpenAIRE

Domingos, Josefa; Loureiro, Rita; Godinho, Catarina; Dean, John; Ferreira, Joaquim J.

2016-01-01

Poster presented at the 4th World Parkinson Congress. Portland, Oregon, 20-23 September 2016 "Objective: To test the applicability of a multitasking boxing program using the BoxMaster® in individuals with Parkinson’s disease that combines motor, cognitive and vocal exercises." N/A

Oregon State Briefing Book for low-level radioactive waste management

International Nuclear Information System (INIS)

1980-12-01

The Oregon State Briefing Book is one of a series of state briefing books on low-level radioactive waste management practices. It has been prepared to assist state and federal agency officials in planning for safe low-level radioactive waste disposal. The report contains a profile of low-level radioactive waste generators in Oregon. The profile is a result of a survey of NRC licensees in Oregon. The briefing book also contains a comprehensive assessment of low-level radioactive waste management issues and concerns as defined by all major interested parties including industry, government, the media, and interest groups. The assessment was developed through personal communications with representatives of interested parties, and through a review of media sources. Lastly, the briefing book provides demographic and socioeconomic data and a discussion of relevant government agencies and activities, all of which may impact waste management practices in Oregon

Oregon State Briefing Book for low-level radioactive waste management

Energy Technology Data Exchange (ETDEWEB)

1980-12-01

The Oregon State Briefing Book is one of a series of state briefing books on low-level radioactive waste management practices. It has been prepared to assist state and federal agency officials in planning for safe low-level radioactive waste disposal. The report contains a profile of low-level radioactive waste generators in Oregon. The profile is a result of a survey of NRC licensees in Oregon. The briefing book also contains a comprehensive assessment of low-level radioactive waste management issues and concerns as defined by all major interested parties including industry, government, the media, and interest groups. The assessment was developed through personal communications with representatives of interested parties, and through a review of media sources. Lastly, the briefing book provides demographic and socioeconomic data and a discussion of relevant government agencies and activities, all of which may impact waste management practices in Oregon.

The uninsured and Medicaid Oregon tobacco user experience in a real world, phone based cessation programme.

Science.gov (United States)

El-Bastawissi, Ay; McAfee, T; Zbikowski, S M; Hollis, J; Stark, M; Wassum, K; Clark, N; Barwinski, R; Broughton, E

2003-03-01

To describe the experience of uninsured and Medicaid Oregon tobacco users who registered in Free & Clear (F&C), a telephone based cessation programme including five scheduled outbound calls. Using a retrospective cohort design, 1334 (423 uninsured, 806 Medicaid, and 105 commercially insured) Oregon tobacco users who registered in F&C between 18 November 1998 and 28 February 2000 were identified and followed for 12 months post-registration; 648 (48.6%) were successfully contacted at 12 months. Information was collected from the F&C database. Unconditional logistic regression, adjusted for race and education, was used. The seven day quit rate at 12 months, assuming non-respondents were smokers, was 14.8% (95% confidence interval (CI) 13.0 to 16.9). This rate was significantly higher among commercially insured participants (v Medicaid but not uninsured) and among participants who completed > or = 5 calls (v or = 5 calls were 60% more likely to quit tobacco (odds ratio (OR) 1.6, 95% CI 0.9 to 3.1), and uninsured respondents who completed > or = 5 calls were 70% more likely to quit tobacco (OR 1.7, 95% CI 0.9 to 3.5), relative to those who completed < 5 calls, but the difference was not significant. The quit rates are similar to those reported in efficacy trials. The observed variation in quitting tobacco for respondents by number of calls completed and by insurance merits further investigation concentrating on increasing compliance with the call schedule, particularly for the uninsured.

Imaging a fossil oolitic system with GPR, insights into the exposures of the Isle of Portland (UK)

Science.gov (United States)

Moreau, Julien; Hansen, Trine L.; Nielsen, Lars

2015-04-01

The Isle of Portland shows exposure of uppermost Jurassic oolitic carbonate all along its coast. The stone of Portland properties are famous as standards for concrete composition, as building material but also for sculpture. As a consequence, the Isle has been quarried intensively for hundreds of years. The regional exposure quality is very high with a potential 3D control. The site has seen generations of geologist trainees coming for field work. The Wessex Basin where the Isle is sitting contains an active petroleum system and the geologists visiting/training there use the carbonates of Portland as an analogue to equivalent Middle-East oil and gas reservoir. Surprisingly, although the site has a tremendous potential to understand the 3D architecture and the sedimentary dynamic of an oolitic system, only punctual observations of logs (1D), sometimes correlated have been published. Several studies place a shore line between the Isle and the continent striking NEE-SWW and facing towards the Channel. Facies changes are attributed to rapid sea-level variations and Walter's Law. We have collected an extensive GPR survey of the same stratigraphic interval (The Portland Freestone). With a total of 99 GPR profiles, we have produced grids on top of most of the coastal cliffs and quarry faces. We have encountered 3 main architectures: 2-m-high bars with steep clinoforms, 10s of metres-wide channels plugged with a variety of organisms and stacked aggrading bundles of multidirectional dunesets. Our dataset does not illustrate any major unconformity which could be attributed to a sharp sea-level drop. We have interpreted our sedimentary architecture to be the result of various hydrodynamic conditions associated with a mix of wave and tide influences. The Isle shows an island barrier complex which progrades into the basin but also expands laterally filling up the available space and cannibalising itself. More proximal facies are effectively observed in the north of the island

Analysis of heavy metal contents in gray and white MTA and 2 kinds of Portland cement: a preliminary study.

Science.gov (United States)

Chang, Seok Woo; Shon, Won Jun; Lee, WooCheol; Kum, Kee Yeon; Baek, Seung Ho; Bae, Kwang Shik

2010-04-01

The levels of 10 heavy metals (arsenic, bismuth, cadmium, chromium, copper, iron, lead, manganese, nickel, and zinc) in gray Portland cement (GPC), white Portland cement (WPC), gray MTA (GMTA), and white MTA (WMTA) were analyzed by inductively coupled plasma-atomic emission spectrometry (ICP-AES). One gram of each material was digested with 80 degrees C "aqua-regia" (7 mL of 60% HNO3 and 21 mL of 35% HCl), filtered, and analyzed by ICP-AES. The analysis was performed 6 times and the data were analyzed statistically. Arsenic and lead concentrations were the highest in GPC (P cements (P Portland cement versus MTA, the differences in purity may be considered. Copyright 2010 Mosby, Inc. All rights reserved.

Evaluation of physico-chemical properties of Portland cements and MTA

Directory of Open Access Journals (Sweden)

Jorge Luis Gonçalves

2010-09-01

Full Text Available The purpose of this study was to evaluate the hydrogenionic potential and electrical conductivity of Portland cements and MTA, as well as the amount of arsenic and calcium released from these materials. In Teflon molds, samples of each material were agitated and added to plastic flasks containing distilled water for 3, 24, 72 and 168 h. The results were analyzed with a Kruskal-Wallis non-parametric test for global comparisons and a Dunn-Tukey test for pairwise comparisons. The results revealed no significant differences in the pH of the materials (p > 0.05. The electrical conductivity of the cements were not statistically different (p > 0.05. White non-structural cement and MTA BIO released the largest amount of calcium ions into solution (p 0.05. The results indicated that the physico-chemical properties of Portland cements and MTA were similar. Furthermore, all materials produced an alkaline environment and can be considered safe for clinical use because arsenic was not released. The electrical conductivity and the amount of calcium ions released into solution increased over time.

Evaluation of physico-chemical properties of Portland cements and MTA.

Science.gov (United States)

Gonçalves, Jorge Luis; Viapiana, Raqueli; Miranda, Carlos Eduardo Saraiva; Borges, Alvaro Henrique; Cruz Filho, Antônio Miranda da

2010-01-01

The purpose of this study was to evaluate the hydrogenionic potential and electrical conductivity of Portland cements and MTA, as well as the amount of arsenic and calcium released from these materials. In Teflon molds, samples of each material were agitated and added to plastic flasks containing distilled water for 3, 24, 72 and 168 h. The results were analyzed with a Kruskal-Wallis non-parametric test for global comparisons and a Dunn-Tukey test for pairwise comparisons. The results revealed no significant differences in the pH of the materials (p > 0.05). The electrical conductivity of the cements were not statistically different (p > 0.05). White non-structural cement and MTA BIO released the largest amount of calcium ions into solution (p 0.05). The results indicated that the physico-chemical properties of Portland cements and MTA were similar. Furthermore, all materials produced an alkaline environment and can be considered safe for clinical use because arsenic was not released. The electrical conductivity and the amount of calcium ions released into solution increased over time.

Utilization of the national Portland cement for immobilizing radioactive wastes - Physical characteristics

International Nuclear Information System (INIS)

Rzyski, B.M.; Suarez, A.A.

1988-01-01

This paper shows the results obtained in the study of the national Portland cement, P320, as matrix for radioactive nitric waste incorporation. Cement use practice in other countries is common for this purposes and demonstrates to be cheap and accessible when low and medium level wastes are immobilized. Some of physical characteristics as: homogeneity,mechanical strenght, setting and porosity are analysed due to water-cement ratio and salt contents. Those characteristics which are proper of the final product, must be controlled in such way to assure a long time integrity of the wasteform. The establishment of process and quality control criteria are based in such kind of data. (author) [pt

The impact of zirconium oxide radiopacifier on the early hydration behaviour of white Portland cement.

Science.gov (United States)

Coleman, Nichola J; Li, Qiu

2013-01-01

Zirconium oxide has been identified as a candidate radiopacifying agent for use in Portland cement-based biomaterials. During this study, the impact of 20 wt.% zirconium oxide on the hydration and setting reactions of white Portland cement (WPC) was monitored by powder X-ray diffraction (XRD), (29)Si and (27)Al magic angle spinning nuclear magnetic resonance spectroscopy (MAS NMR), transmission electron microscopy (TEM) and Vicat apparatus. The presence of 20 wt.% zirconium oxide particles in the size-range of 0.2 to 5 μm was found to reduce the initial and final setting times of WPC from 172 to 147 min and 213 to 191 min, respectively. Zirconium oxide did not formally participate in the chemical reactions of the hydrating cement; however, the surface of the zirconium oxide particles presented heterogeneous nucleation sites for the precipitation and growth of the early C-S-H gel products which accelerated the initial setting reactions. The presence of zirconium oxide was found to have little impact on the development of the calcium (sulpho)aluminate hydrate phases. Copyright © 2012 Elsevier B.V. All rights reserved.

Industrial Wastes as Alternative Mineral Addition in Portland Cement and as Aggregate in Coating Mortars

OpenAIRE

Oliveira, Kamilla Almeida; Nazário, Bruna Inácio; Oliveira, Antonio Pedro Novaes de; Hotza, Dachamir; Raupp-Pereira, Fabiano

2017-01-01

This paper presents an evaluation study of wastes from pulp and paper as well as construction and demolition industries for application in cement-based materials. The alternative raw materials were used as a source of calcium carbonate (CaCO3) and as pozzolanic material (water-reactive SiO2) in partial replacement of Portland cement. In addition to the hydraulic binder, coating mortars were composed by combining the pulp and paper fluidized bed sand residue with construction and demolition wa...

A Mid-Level Dental Provider in Oregon: Dental hygienists' perceptions.

Science.gov (United States)

Coplen, Amy E; Bell, Kathryn; Aamodt, Gail L; Ironside, Lynn

2017-10-01

Purpose: Many states are exploring alternative provider models and examining the role of the dental hygienist to address access to care challenges as the United States continues to face increasing demands for oral healthcare services. The purpose of this study was to assess dental hygienists' opinions in the state of Oregon regarding the current limitations of dental hygienists' scope of practice, perceived need for a mid-level provider in Oregon, and personal interest in becoming a mid-level provider. Methods: In December 2013 a survey was mailed to a sample of 1,231 dental hygienists registered in Oregon representing 30% of the licentiates. All licentiates holding expanded practice permits (EPP) were included in the sample (n=351). The following categories were included in the 32-question survey: scope of practice, mid-level provider, current practice, and demographics. Results: A total of 440 surveys were returned for a response rate of 36%. Of the EPP holders, 51% responded to the survey. Over half of respondents (59%) believe that a mid-level provider is needed in the state. Respondents holding membership in the American Dental Hygienists' Association, as well as EPP holders, were significantly more likely to respond that a mid-level dental provider was needed in the state (plevel provider was introduced in Oregon, the new provider should be a registered dental hygienist model. Forty-three percent (n=186) of respondents were interested in becoming mid-level providers and 47% (n=203) of respondents believed that the minimum education for a mid-level provider should be a bachelor's degree. The majority, 74% (n=137), of those interested in becoming a mid-level provider indicated a preference in completing their education through online teaching combined with a clinical internship. Conclusion: There is strong support from dental hygienists in Oregon that a need exists for a mid-level dental provider and that this provider model should be dental hygiene based

X-ray diffractometry of steam cured ordinary Portland and blast-furnace-slag cements

International Nuclear Information System (INIS)

Camarini, G.; Djanikian, J.G.

1994-01-01

This work studies some aspects of the phases produced by hydration of ordinary and blast-furnace-slag cements, at normal conditions and steam cured (60 and 95 0 C), using an X-ray diffraction technique. The blast-furnace-slag cement was a mixture of 50% of ordinary Portland cement and 50% of blast-furnace-slag (separately grinding). After curing the X-ray diffraction reveals that, in relation to ordinary Portland cement, the main phases in blast-furnace-slag cement are hydrated silicates and aluminates, hydro garnet, etringitte and mono sulphate. After steam curing the hydration of blast-furnace-slag cement proceeds. This is a result of the slag activation by the curing temperature. (author). 8 refs., 3 figs., 1 tab

Portland cement concrete pavement review of QC/QA data 2000 through 2009.

Science.gov (United States)

2011-04-01

This report analyzes the Quality Control/Quality Assurance (QC/QA) data for Portland cement concrete pavement : (PCCP) awarded in the years 2000 through 2009. Analysis of the overall performance of the projects is accomplished by : reviewing the Calc...

Natural cement as the precursor of Portland cement: Methodology for its identification

International Nuclear Information System (INIS)

Varas, M.J.; Alvarez de Buergo, M.; Fort, R.

2005-01-01

When cements appeared in the 19th century, they took the place of traditional binding materials (lime, gypsum, and hydraulic lime) which had been used until that time. Early cements can be divided into two groups, natural and artificial (Portland) cements. Natural cements were introduced first, but their widespread usage was short-lived as they were quickly replaced by artificial cements (Portland), still the most important and predominant today. The main differences between natural and artificial cements arise during the manufacturing process. The final properties of the cements are greatly influenced by differences in the raw materials and burning temperatures employed. The aim of this paper is to assess the efficiency of traditional analytical techniques (petrographic microscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FTIR)) used to differentiate natural and artificial cements

Four Decades of Systems Science Teaching and Research in the USA at Portland State University

Directory of Open Access Journals (Sweden)

Wayne Wakeland

2014-04-01

Full Text Available Systems science is defined in general fashion, and a brief background is provided that lists some of the systems science-related societies, conferences, journals, research institutes, and educational programs. The Systems Science Graduate Program at Portland State University in Portland, OR, USA, is described in detail, including its history, curriculum, students, faculty, and degrees granted. Dissertation topics are summarized via word diagrams created from dissertation titles over the years. MS degrees, student placement, and undergraduate courses are also mentioned, and future plans for the program are described including its support for sustainability education.

X-ray diffractometry of steam cured ordinary Portland and blast-furnace-slag cements; Difratometria de raios X de pastas de cimento Portland comum e de alto-forno submetidas a cura termica

Energy Technology Data Exchange (ETDEWEB)

Camarini, G [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia; Djanikian, J G [Sao Paulo Univ., SP (Brazil). Escola Politecnica

1994-12-31

This work studies some aspects of the phases produced by hydration of ordinary and blast-furnace-slag cements, at normal conditions and steam cured (60 and 95{sup 0} C), using an X-ray diffraction technique. The blast-furnace-slag cement was a mixture of 50% of ordinary Portland cement and 50% of blast-furnace-slag (separately grinding). After curing the X-ray diffraction reveals that, in relation to ordinary Portland cement, the main phases in blast-furnace-slag cement are hydrated silicates and aluminates, hydro garnet, etringitte and mono sulphate. After steam curing the hydration of blast-furnace-slag cement proceeds. This is a result of the slag activation by the curing temperature. (author). 8 refs., 3 figs., 1 tab.

Recycled Portland cement concrete pavements : Part II, state-of-the art summary.

Science.gov (United States)

1979-01-01

This report constitutes a review of the literature concerning recycling of portland cement concrete pavements by crushing the old pavement and reusing the crushed material as aggregate in a number of applications. A summary of the major projects cond...

2015 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar: Upper Rogue 3DEP

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Quantum Spatial collected Light Detection and Ranging (LiDAR) data for the Oregon LiDAR Consortium (OLC) Upper Rogue 2015 study area. The collection of high...

Parenting--Challenge and Commitment

Science.gov (United States)

Luckey, Eleanore Braun

1973-01-01

This is a revised version of the National Council on Family Relations Presidential address delivered November 3, 1972, Portland Oregon. This address concerned the new constitution and reorganization of N.C.F.R. and a plea for reexamination of the membership's commitment to family issues. (JC)

Thermal analysis of borogypsum and its effects on the physical properties of Portland cement

International Nuclear Information System (INIS)

Elbeyli, Iffet Yakar; Derun, Emek Moeroeydor; Guelen, Jale; Piskin, Sabriye

2003-01-01

Borogypsum, which consists mainly of gypsum crystals, B 2 O 3 and some impurities, is formed during the production of boric acid from colemanite, which is an important borate ore. In this study, the effect of borogypsum and calcined borogypsum on the physical properties of ordinary Portland cement (OPC) has been investigated. The calcination temperature and transformations in the structures of borogypsum and natural gypsum were determined by differential thermal analysis (DTA), thermogravimetric analysis (TGA) and X-ray diffraction (XRD) techniques. Thermal experiments were carried out between ambient temperature and 500 deg. C in an air atmosphere at a heating rate of 10 deg. C min -1 . After calculation of enthalpy and determination of conversion temperatures, borogypsum (5% and 7%), hemihydrate borogypsum (5%) and natural gypsum (5%) were added separately to Portland cement clinker and cements were ground in the laboratory. The final products were tested for chemical analysis, compressive strength, setting time, Le Chatelier expansion and fineness properties according to the European Standard (EN 196). The results show that increasing the borogypsum level in Portland cement from 5% to 7% caused an increase in setting time and a decrease in soundness expansion and compressive strength. The cement prepared with borogypsum (5%) was found to have similar strength properties to those obtained with natural gypsum, whereas a mixture containing 5% of hemihydrate borogypsum was found to develop 25% higher compressive strength than the OPC control mixtures at 28 days. For this reason, utilization of calcined borogypsum in cement applications is expected to give better results than untreated borogypsum. It is concluded that hemihydrate borogypsum could be used as a retarder for Portland cement as an industrial side. This would play an important role in reducing environmental pollution

LEVEL AND EXTENT OF MERCURY CONTAMINATION IN OREGON LOTIC FISH

Science.gov (United States)

As part of the U.S. EPA's EMAP Oregon Pilot project, we conducted a probability survey of 154 Oregon streams and rivers to assess the spatial extent of mercury (Hg) contamination in fish tissue across the state. Samples consisted of whole fish analyses of both small (< 120 mm) a...

Effects of the super plasticizers and the water/cement ratio on the mini-slump of Portland cement pastes

International Nuclear Information System (INIS)

Meirelles, J.R.; Morelli, A.C.; Baldo, J.B.

1998-01-01

The rheology of Portland cement concrete is dominated by the cement paste rheology. In general the rheological behavior of cement pastes is evaluated by means of the mini-slump test. In the present paper it was investigated the effect of the water/cement ratio was as of two types of superplasticizers (melamine and naftalen based) on the mini-slump of pastes of common cement pastes. (author)

Portland blended cements: demolition ceramic waste management

International Nuclear Information System (INIS)

Trezza, M.A.; Zito, S.; Tironi, A.; Irassar, E.F.; Rahhal, V.F.

2017-01-01

Demolition ceramic wastes (DCWs) were investigated in order to determine their potential use as supplementary cementitious materials in Portland Blended Cements (PBCs). For this purpose, three ceramic wastes were investigated. After characterization of the materials used, the effect of ceramic waste replacement (8, 24 and 40% by mass) was analyzed. Pozzolanic activity, hydration progress, workability and compressive strength were determined at 2, 7 and 28 days. The results showed that the ground wastes behave as filler at an early age, but as hydration progresses, the pozzolanic activity of ceramic waste contributes to the strength requirement. [es

Residential Energy Efficiency Potential: Oregon

Energy Technology Data Exchange (ETDEWEB)

Wilson, Eric J [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-11-02

Energy used by Oregon single-family homes that can be saved through cost-effective improvements. Prepared by Eric Wilson and Noel Merket, NREL, and Erin Boyd, U.S. Department of Energy Office of Energy Policy and Systems Analysis.

Influence of limestone on the hydration of Portland cements

International Nuclear Information System (INIS)

Lothenbach, Barbara; Le Saout, Gwenn; Gallucci, Emmanuel; Scrivener, Karen

2008-01-01

The influence of the presence of limestone on the hydration of Portland cement was investigated. Blending of Portland cement with limestone was found to influence the hydrate assemblage of the hydrated cement. Thermodynamic calculations as well as experimental observations indicated that in the presence of limestone, monocarbonate instead of monosulfate was stable. Thermodynamic modelling showed that the stabilisation of monocarbonate in the presence of limestone indirectly stabilised ettringite leading to a corresponding increase of the total volume of the hydrate phase and a decrease of porosity. The measured difference in porosity between the 'limestone-free' cement, which contained less than 0.3% CO 2 , and a cement containing 4% limestone, however, was much smaller than calculated. Coupling of thermodynamic modelling with a set of kinetic equations which described the dissolution of the clinker, predicted quantitatively the amount of hydrates. The quantities of ettringite, portlandite and amorphous phase as determined by TGA and XRD agreed well with the calculated amounts of these phases after different periods of time. The findings in this paper show that changes in the bulk composition of hydrating cements can be followed by coupled thermodynamic models. Comparison between experimental and modelled data helps to understand in more detail the dominating processes during cement hydration

76 FR 76760 - Gray Portland Cement and Cement Clinker From Japan

Science.gov (United States)

2011-12-08

... and Cement Clinker From Japan Determination On the basis of the record \\1\\ developed in the subject... duty order on gray Portland cement and cement clinker from Japan would be likely to lead to... and Cement Clinker from Japan: Investigation No. 731- TA-461 (Third Review). By order of the...

2016 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar DEM: McKenzie River

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Quantum Spatial collected Light Detection and Ranging (LiDAR) data for the Oregon LiDAR Consortium (OLC) McKenzie River study area. This study area is located near...

Durabilidad de un suelo contaminado y tratado con cemento portland Durability of a contaminated soil treated with portland cement

OpenAIRE

José W Jiménez Rojas; Nilo C Consoli; Karla Salvagni Heineck

2008-01-01

Este trabajo tiene por objetivo la aplicación de la técnica de solidificación/estabilización de suelos contaminados, analizando específicamente el comportamiento físico del suelo a través de ensayos de durabilidad. El suelo fue contaminado en laboratorio con residuo oleoso y la aplicación de la técnica tuvo cómo agente de encapsulamiento el cemento Portland CP V-ARI. Los ensayos de durabilidad, realizados según la NBR 13554 (1996), tuvieron como objetivo estudiar el grado de desagregación y v...

The AFm phase in Portland cement

International Nuclear Information System (INIS)

Matschei, T.; Lothenbach, B.; Glasser, F.P.

2007-01-01

The AFm phase of Portland cements refers to a family of hydrated calcium aluminates based on the hydrocalumite-like structure of 4CaO.Al 2 O 3 .13-19 H 2 O. However OH - may be replaced by SO 4 2- and CO 3 2- . Except for limited replacement (50 mol%, maximum) of sulfate by hydroxide, these compositions do not form solid solutions and, from the mineralogical standpoint, behave as separate phases. Therefore many hydrated cements will contain mixtures of AFm phases. AFm phases have been made from precursors and experimentally-determined phase relationships are depicted at 25 deg. C. Solubility data are reported and thermodynamic data are derived. The 25 deg. C stability of AFm phases is much affected by the nature of the anion: carbonate stabilises AFm and displaces OH and SO 4 at species activities commonly encountered in cement systems. However in the presence of portlandite, and as carbonate displaces sulfate in AFm, the reaction results in changes in the amount of both portlandite and ettringite: specimen calculations are presented to quantify these changes. The scheme of phase balances enables calculation of the mineralogical balances of a hydrated cement paste with greater accuracy than hitherto practicable

Evaluation of dynamic elasticity module in samples of Portland (type 1) cement paste exposed to neutronic irradiation

International Nuclear Information System (INIS)

Rosa Junior, A.A.; Lucki, G.

1986-01-01

The fast neutron radiation effects and temperature on Portland cement are studied. The Dynamic Elasticity Module (Ed) in samples of Portland cement paste was evaluated. Ultrassonic technics were applied (resonance frequency and pulse velocity). The samples were irradiated with fast neutrons to fluence of 7,2 x 10 18 n/cm 2 (E approx. 1 MeV), at temperature of 120 + - 5 0 C, due to gamma heating. This temperature was simulated in laboratory in a microwave oven. (Author) [pt

Portland cement hydration and early setting of cement stone intended for efficient paving materials

Science.gov (United States)

Grishina, A.

2017-10-01

Due to the growth of load on automotive roads, modern transportation engineering is in need of efficient paving materials. Runways and most advanced highways require Portland cement concretes. This makes important the studies directed to improvement of binders for such concretes. In the present work some peculiarities of the process of Portland cement hydration and early setting of cement stone with barium hydrosilicate sol were examined. It was found that the admixture of said sol leads to a shift in the induction period to later times without significant change in its duration. The admixture of a modifier with nanoscale barium hydrosilicates increases the degree of hydration of the cement clinker minerals and changes the phase composition of the hydration products; in particular, the content of portlandite and tricalcium silicate decreases, while the amount of ettringite increases. Changes in the hydration processes of Portland cement and early setting of cement stone that are caused by the nanoscale barium hydrosilicates, allow to forecast positive technological effects both at the stage of manufacturing and at the stage of operation. In particular, the formwork age can be reduced, turnover of molds can be increased, formation of secondary ettringite and corrosion of the first type can be eliminated.

Benthic assemblages of mega epifauna on the Oregon continental margin

Science.gov (United States)

Hemery, Lenaïg G.; Henkel, Sarah K.; Cochrane, Guy R.

2018-01-01

Environmental assessment studies are usually required by a country's administration before issuing permits for any industrial activities. One of the goals of such environmental assessment studies is to highlight species assemblages and habitat composition that could make the targeted area unique. A section of the Oregon continental slope that had not been previously explored was targeted for the deployment of floating wind turbines. We carried out an underwater video survey, using a towed camera sled, to describe its benthic assemblages. Organisms were identified to the lowest taxonomic level possible and assemblages described related to the nature of the seafloor and the depth. We highlighted six invertebrate assemblages and three fish assemblages. For the invertebrates within flat soft sediments areas we defined three different assemblages based on primarily depth: a broad mid-depth (98–315 m) assemblage dominated by red octopus, sea pens and pink shrimps; a narrower mid-depth (250–270 m) assemblage dominated by box crabs and various other invertebrates; and a deeper (310–600 m) assemblage dominated by sea urchins, sea anemones, various snails and zoroasterid sea stars. The invertebrates on mixed sediments also were divided into three different assemblages: a shallow (~100 m deep) assemblage dominated by plumose sea anemones, broad mid-depth (170–370 m) assemblage dominated by sea cucumbers and various other invertebrates; and, again, a narrower mid-depth (230–270 m) assemblage, dominated by crinoids and encrusting invertebrates. For the fish, we identified a rockfish assemblage on coarse mixed sediments at 170–370 m and another fish assemblage on smaller mixed sediments within that depth range (250–370 m) dominated by thornyheads, poachers and flatfishes; and we identified a wide depth-range (98–600 m) fish assemblage on flat soft sediments dominated by flatfishes, eelpouts and thornyheads. Three of these assemblages (the two

Benthic assemblages of mega epifauna on the Oregon continental margin

Science.gov (United States)

Hemery, Lenaïg G.; Henkel, Sarah K.; Cochrane, Guy R.

2018-05-01

Environmental assessment studies are usually required by a country's administration before issuing permits for any industrial activities. One of the goals of such environmental assessment studies is to highlight species assemblages and habitat composition that could make the targeted area unique. A section of the Oregon continental slope that had not been previously explored was targeted for the deployment of floating wind turbines. We carried out an underwater video survey, using a towed camera sled, to describe its benthic assemblages. Organisms were identified to the lowest taxonomic level possible and assemblages described related to the nature of the seafloor and the depth. We highlighted six invertebrate assemblages and three fish assemblages. For the invertebrates within flat soft sediments areas we defined three different assemblages based on primarily depth: a broad mid-depth (98-315 m) assemblage dominated by red octopus, sea pens and pink shrimps; a narrower mid-depth (250-270 m) assemblage dominated by box crabs and various other invertebrates; and a deeper (310-600 m) assemblage dominated by sea urchins, sea anemones, various snails and zoroasterid sea stars. The invertebrates on mixed sediments also were divided into three different assemblages: a shallow ( 100 m deep) assemblage dominated by plumose sea anemones, broad mid-depth (170-370 m) assemblage dominated by sea cucumbers and various other invertebrates; and, again, a narrower mid-depth (230-270 m) assemblage, dominated by crinoids and encrusting invertebrates. For the fish, we identified a rockfish assemblage on coarse mixed sediments at 170-370 m and another fish assemblage on smaller mixed sediments within that depth range (250-370 m) dominated by thornyheads, poachers and flatfishes; and we identified a wide depth-range (98-600 m) fish assemblage on flat soft sediments dominated by flatfishes, eelpouts and thornyheads. Three of these assemblages (the two broad fish assemblages and the deep

Mineral Trioxide Aggregate and Portland Cement for Direct Pulp Capping in Dog: A Histopathological Evaluation

Directory of Open Access Journals (Sweden)

Maryam Bidar

2014-09-01

Full Text Available Background and aims. Mineral trioxide aggregate and calcium hydroxide are considered the gold standard pulp-capping materials. Recently, Portland cement has been introduced with properties similar to those of mineral trioxide aggregate. His-topathological effects of direct pulp capping using mineral trioxide aggregate and Portland cements on dog dental pulp tis-sue were evaluated in the present study. Materials and methods. This histopatological study was carried out on 64 dog premolars. First, the pulp was exposedwith a sterile bur. Then, the exposed pulp was capped with white or gray mineral trioxide aggregates and white or gray Port-land cements in each quadrant and sealed with glass-ionomer. The specimens were evaluated under a light microscope after 6 months. Statistical analysis was carried out using Kruskal-Wallis test. Statistical significance was defined at α=5%. Results. There was no acute inflammation in any of the specimens. Chronic inflammation in white and gray mineral triox-ide aggregates and white and gray Portland cements was reported to be 45.5%, 27.3%, 57.1% and 34.1%, respectively. Al-though the differences were not statistically significant, severe inflammation was observed mostly adjacent to white mineral trioxide aggregate. The largest extent of increased vascularization (45% and the least increase in fibrous tissue were ob-served adjacent to white mineral trioxide aggregate, with no significant differences. In addition, the least calcified tissue formed adjacent to white mineral trioxide aggregate, although the difference was not significant. Conclusion. The materials used in this study were equally effective as pulp protection materials following direct pulp cap-ping in dog teeth.

Predicting the durability of Portland cement systems in aggressive environments--Laboratory validation

International Nuclear Information System (INIS)

Maltais, Y.; Samson, E.; Marchand, J.

2004-01-01

Portland cement systems are often exposed to severe environments, and their long-term performance is of concern. The main results of a comprehensive investigation of deterioration processes that may affect the behavior of Portland cement systems exposed to chemically aggressive environments is presented. As part of this investigation, well-cured cement paste discs were fully characterized and exposed to deionized water and sodium sulfate solutions. Degradation experiments were conducted under saturated and unsaturated conditions. At the end of the exposure period, microstructural alterations were investigated by microprobe analyses, scanning electron microscope observations and energy-dispersive X-ray analyses. Test results provide information on the basic aspects of various degradation phenomena, such as decalcification and external sulfate attack. Experimental results were also compared with results obtained by a numerical model. The analysis reveals that the intricate microstructural features of the degraded samples could be accurately reproduced by the model

The Oregon Public Health Policy Institute: Building Competencies for Public Health Practice

Science.gov (United States)

Yoon, Jangho; Bernell, Stephanie; Tynan, Michael; Alvarado, Carla Sarai; Eversole, Tom; Mosbaek, Craig; Beathard, Candice

2015-01-01

The Oregon Public Health Policy Institute (PHPI) was designed to enhance public health policy competencies among state and local health department staff. The Oregon Health Authority funded the College of Public Health and Human Sciences at Oregon State University to develop the PHPI curriculum in 2012 and offer it to participants from 4 state public health programs and 5 local health departments in 2013. The curriculum interspersed short instructional sessions on policy development, implementation, and evaluation with longer hands-on team exercises in which participants applied these skills to policy topics their teams had selected. Panel discussions provided insights from legislators and senior Oregon health experts. Participants reported statistically significant increases in public health policy competencies and high satisfaction with PHPI overall. PMID:26066925

A Bayesian-Based Approach to Marine Spatial Planning: Evaluating Spatial and Temporal Variance in the Provision of Ecosystem Services Before and After the Establishment Oregon's Marine Protected Areas

Science.gov (United States)

Black, B.; Harte, M.; Goldfinger, C.

2017-12-01

Participating in a ten-year monitoring project to assess the ecological, social, and socioeconomic impacts of Oregon's Marine Protected Areas (MPAs), we have worked in partnership with the Oregon Department of Fish and Wildlife (ODFW) to develop a Bayesian geospatial method to evaluate the spatial and temporal variance in the provision of ecosystem services produced by Oregon's MPAs. Probabilistic (Bayesian) approaches to Marine Spatial Planning (MSP) show considerable potential for addressing issues such as uncertainty, cumulative effects, and the need to integrate stakeholder-held information and preferences into decision making processes. To that end, we have created a Bayesian-based geospatial approach to MSP capable of modelling the evolution of the provision of ecosystem services before and after the establishment of Oregon's MPAs. Our approach permits both planners and stakeholders to view expected impacts of differing policies, behaviors, or choices made concerning Oregon's MPAs and surrounding areas in a geospatial (map) format while simultaneously considering multiple parties' beliefs on the policies or uses in question. We quantify the influence of the MPAs as the shift in the spatial distribution of ecosystem services, both inside and outside the protected areas, over time. Once the MPAs' influence on the provision of coastal ecosystem services has been evaluated, it is possible to view these impacts through geovisualization techniques. As a specific example of model use and output, a user could investigate the effects of altering the habitat preferences of a rockfish species over a prescribed period of time (5, 10, 20 years post-harvesting restrictions, etc.) on the relative intensity of spillover from nearby reserves (please see submitted figure). Particular strengths of our Bayesian-based approach include its ability to integrate highly disparate input types (qualitative or quantitative), to accommodate data gaps, address uncertainty, and to

33 CFR 117.861 - Blind Slough.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Blind Slough. 117.861 Section 117.861 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements Oregon § 117.861 Blind Slough. The draws of the Portland and...

Invited Colloquium on Negotiating the Complexities of Multilingual Assessment, AAAL Conference 2014

Science.gov (United States)

Menken, Kate; Shohamy, Elana

2015-01-01

The invited colloquium on New Directions in Language Assessment held at the American Association for Applied Linguistics (AAAL) annual meeting in Portland, Oregon on March 22, 2014 brought together an international panel of scholars to together explore the possibilities and challenges of translanguaging and bi/multilingual approaches in…

NESHAP for the Portland Cement Manufacturing Industry: Fact Sheets for Actions Since 2015

Science.gov (United States)

EPA is extending its approval for the use of an alternative method to show compliance with hydrogen chloride (HCl) emissions limits in the National Emission Standards for Hazardous Air Pollutants for the Portland Cement Manufacturing Industry

Aircraft observations of aerosols O3 and NOy in a nighttime urban plume

International Nuclear Information System (INIS)

Berkowitz, C.M.; Zaveri, R.A.; Xindi Bian; Shiyuan Zhong; Disselkamp, R.S.; Laulainen, N.S.; Chapman, E.G.

2001-01-01

Nighttime measurements of aerosol surface area, O 3 , NO y and moisture were made downwind of Portland, Oregon, as part of a study to characterize the chemistry in a nocturnal urban plume. Air parcels sampled within the urban plume soon after sunset had positive correlations between O 3 , relative humidity, NO y and aerosol number density. However, the air parcels sampled within the urban plume just before dawn had O 3 mixing ratios that were highly anti-correlated with aerosol number density, NO y and relative humidity. Back-trajectories from a mesoscale model show that both the post-sunset and pre-dawn parcels came from a common maritime source to the northwest of Portland. The pre-dawn parcels with strong anti-correlations passed directly over Portland in contrast to the other parcels that were found to pass west of Portland. Several gas-phase mechanisms and a heterogeneous mechanism involving the loss of O 3 to the aerosol surface, are examined to explain the observed depletion in O 3 within the pre-dawn parcels that had passed over Portland. (Author)

Timber resources of southwest Oregon.

Science.gov (United States)

Patricia M. Bassett

1979-01-01

This report presents statistics from a 1973 inventory of timber resources of Douglas County and from a 1974 inventory of timber resources of Coos, Curry, Jackson, and Josephine Counties, Oregon. Tables presented are of forest area and of timber volume, growth, and mortality.

Annual Coded Wire Tag Program; Oregon Missing Production Groups, 1995 Annual Report.

Energy Technology Data Exchange (ETDEWEB)

Garrison, Robert L.; Mallette, Christine; Lewis, Mark A.

1995-12-01

Bonneville Power Administration is the funding source for the Oregon Department of Fish and Wildlife`s Annual Coded Wire Tag Program - Oregon Missing Production Groups Project. Tule brood fall chinook were caught primarily in the British Columbia, Washington and northern Oregon ocean commercial fisheries. The up-river bright fall chinook contributed primarily to the Alaska and British Columbia ocean commercial fisheries and the Columbia River gillnet fishery. Contribution of Rogue fall chinook released in the lower Columbia River system occurred primarily in the Oregon ocean commercial and Columbia river gillnet fisheries Willamette spring chinook salmon contributed primarily to the Alaska and British Columbia ocean commercial, Oregon freshwater sport and Columbia River gillnet fisheries. Restricted ocean sport and commercial fisheries limited contribution of the Columbia coho released in the Umatilla River that survived at an average rate of 1.05% and contributed primarily to the Washington, Oregon and California ocean sport and commercial fisheries and the Columbia River gillnet fishery. The 1987 to 1991 brood years of coho released in the Yakima River survived at an average rate of 0.64% and contributed primarily to the Washington, Oregon and California ocean sport and commercial fisheries and the Columbia River gillnet fishery. Survival rates of salmon and steelhead are influenced, not only by factors in the hatchery, disease, density, diet and size and time of release, but also by environmental factors in the river and ocean. These environmental factors are controlled by large scale weather patterns such as El Nino over which man has no influence. Man could have some influence over river flow conditions, but political and economic pressures generally out weigh the biological needs of the fish.

2015 Oregon Department of Geology and Mineral Industries (DOGAMI) Oregon Lidar DEM: Upper Rogue 3DEP

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Quantum Spatial collected Light Detection and Ranging (LiDAR) data for the Oregon LiDAR Consortium (OLC) Upper Rogue 2015 study area. The collection of high...

Healing of apical rarefaction of three nonvital open apex anterior teeth using a white portland cement apical plug

Directory of Open Access Journals (Sweden)

Amitabha Chakraborty

2012-01-01

Full Text Available The major challenge of performing root canal treatment in an open apex pulp-less tooth is to obtain a good apical seal. MTA has been successfully used to achieve a good apical seal, wherein the root canal obturation can be done immediately. MTA and White Portland Cement has been shown similarity in their physical, chemical and biological properties and has also shown similar outcome when used in animal studies and human trials. In our study, open apex of three non vital upper central incisors has been plugged using modified white Portland cement. 3 to 6 months follow up revealed absence of clinical symptoms and disappearance of peri-apical rarefactions. The positive clinical outcome may encourage the future use of white Portland cement as an apical plug material in case of non vital open apex tooth as much cheaper substitute of MTA.

Effects of chemical and mineral additives and the water/cement ratio on the thermal resistance of Portland cement concrete

International Nuclear Information System (INIS)

Cesar, Leandro Cesar Dias; Morelli, Arnaldo C.; Baldo, Joao Baptista

1998-01-01

The exposure of Portland concrete to high temperatures (>250 deg C) can damage drastically the microstructural integrity of the material. Since the water/cement ratio as well as the inclusion of superplasticizers and mineral additives (silica fume) can alter constitutively and micro structurally the material, in this work it was investigated per effect of these additions on the damage resistance of portland concrete after exposure to high temperatures. (author)

Assessment of diabetic teleretinal imaging program at the Portland Department of Veterans Affairs Medical Center.

Science.gov (United States)

Tsan, Grace L; Hoban, Keely L; Jun, Weon; Riedel, Kevin J; Pedersen, Amy L; Hayes, John

2015-01-01

We conducted a retrospective chart review of 200 diabetic patients who had teleretinal imaging performed between January 1, 2010, and January 1, 2011, at Portland Department of Veterans Affairs (VA) Medical Center outpatient clinics to assess the effectiveness of the diabetic teleretinal imaging program. Twenty patients (10%) had diabetic retinopathy. Ninety percent of the available teleretinal imaging studies were of adequate quality for interpretation. In accordance with local VA policy at that time, all teleretinal imaging patients should have been referred for a dilated retinal examination the following year. Image readers referred 97.5% of the patients to eye clinics for subsequent eye examinations, but the imagers scheduled appointments for only 80% of these patients. The redundancy rate, i.e., patients who had an eye examination within the past 6 mo, was 11%; the duplicate recall rate, i.e., patients who had a second teleretinal imaging performed within 1 yr of the eye examination, was 37%. Rates of timely diabetic eye examinations at clinics with teleretinal imaging programs, particularly when teleretinal imaging and eye clinics were colocated at the same community-based outpatient clinic, were higher than those without a teleretinal imaging program. We concluded that the Portland VA Medical Center's teleretinal imaging program was successful in increasing the screening rate for diabetic retinopathy.

Medical Marijuana Legalization and Marijuana Use Among Youth in Oregon.

Science.gov (United States)

Paschall, Mallie J; Grube, Joel W; Biglan, Anthony

2017-06-01

While the legalization of marijuana for medical and recreational use has raised concerns about potential influences on marijuana use and beliefs among youth, few empirical studies have addressed this issue. We examined the association between medical marijuana patients and licensed growers per 1000 population in 32 Oregon counties from 2006 to 2015, and marijuana use among youth over the same period. We obtained data on registered medical marijuana patients and licensed growers from the Oregon Medical Marijuana Program and we obtained data on youth marijuana use, perceived parental disapproval, and demographic characteristics from the Oregon Healthy Teens Survey. Across 32 Oregon counties, the mean rate of marijuana patients per 1000 population increased from 2.9 in 2006 to 18.3 in 2015, whereas the grower rate increased from 3.8 to 11.9. Results of multi-level analyses indicated significant positive associations between rates of marijuana patients and growers per 1000 population and the prevalence of past 30-day marijuana use, controlling for youth demographic characteristics. The marijuana patient and grower rates were also inversely associated with parental disapproval of marijuana use, which decreased from 2006 to 2015 and acted as a mediator. These findings suggest that a greater number of registered marijuana patients and growers per 1000 population in Oregon counties was associated with a higher prevalence of marijuana use among youth from 2006 to 2015, and that this relationship was partially attributable to perceived norms favorable towards marijuana use.

Hydration of Portland cement with additions of calcium sulfoaluminates

International Nuclear Information System (INIS)

Le Saoût, Gwenn; Lothenbach, Barbara; Hori, Akihiro; Higuchi, Takayuki; Winnefeld, Frank

2013-01-01

The effect of mineral additions based on calcium aluminates on the hydration mechanism of ordinary Portland cement (OPC) was investigated using isothermal calorimetry, thermal analysis, X-ray diffraction, scanning electron microscopy, solid state nuclear magnetic resonance and pore solution analysis. Results show that the addition of a calcium sulfoaluminate cement (CSA) to the OPC does not affect the hydration mechanism of alite but controls the aluminate dissolution. In the second blend investigated, a rapid setting cement, the amorphous calcium aluminate reacts very fast to ettringite. The release of aluminum ions strongly retards the hydration of alite but the C–S–H has a similar composition as in OPC with no additional Al to Si substitution. As in CSA–OPC, the aluminate hydration is controlled by the availability of sulfates. The coupling of thermodynamic modeling with the kinetic equations predicts the amount of hydrates and pore solution compositions as a function of time and validates the model in these systems.

Oregon's Death With Dignity Act: 20 Years of Experience to Inform the Debate.

Science.gov (United States)

Hedberg, Katrina; New, Craig

2017-10-17

Twenty years ago, Oregon voters approved the Death With Dignity Act, making Oregon the first state in the United States to allow physicians to prescribe medications to be self-administered by terminally ill patients to hasten their death. This report summarizes the experience in Oregon, including the numbers and types of participating patients and providers. These data should inform the ongoing policy debate as additional jurisdictions consider such legislation.

Grow Plants the Organic Way: Give Them the Soil Microbes They Crave

Directory of Open Access Journals (Sweden)

Phil Mixter

2013-03-01

Full Text Available Review of: Teaming with Microbes: The Organic Gardener’s Guide to the Soil Food Web, revised ed.; Jeff Lowenfels and Wayne Lewis; (2010. Timber Press Inc., Portland, OR. 220 pages.

Performance Characteristics of Waste Glass Powder Substituting Portland Cement in Mortar Mixtures

Science.gov (United States)

Kara, P.; Csetényi, L. J.; Borosnyói, A.

2016-04-01

In the present work, soda-lime glass cullet (flint, amber, green) and special glass cullet (soda-alkaline earth-silicate glass coming from low pressure mercury-discharge lamp cullet and incandescent light bulb borosilicate glass waste cullet) were ground into fine powders in a laboratory planetary ball mill for 30 minutes. CEM I 42.5N Portland cement was applied in mortar mixtures, substituted with waste glass powder at levels of 20% and 30%. Characterisation and testing of waste glass powders included fineness by laser diffraction particle size analysis, specific surface area by nitrogen adsorption technique, particle density by pycnometry and chemical analysis by X-ray fluorescence spectrophotometry. Compressive strength, early age shrinkage cracking and drying shrinkage tests, heat of hydration of mortars, temperature of hydration, X-ray diffraction analysis and volume stability tests were performed to observe the influence of waste glass powder substitution for Portland cement on physical and engineering properties of mortar mixtures.

DecAID: a decaying wood advisory model for Oregon and Washington.

Science.gov (United States)

Kim Mellen; Bruce G. Marcot; Janet L. Ohmann; Karen L. Waddell; Elizabeth A. Willhite; Bruce B. Hostetler; Susan A. Livingston; Cay. Ogden

2002-01-01

DecAID is a knowledge-based advisory model that provides guidance to managers in determining the size, amount, and distribution of dead and decaying wood (dead and partially dead trees and down wood) necessary to maintain wildlife habitat and ecosystem functions. The intent of the model is to update and replace existing snag-wildlife models in Washington and Oregon....

Pyrogenic carbon emission from a large wildfire in Oregon, United States.

Science.gov (United States)

J. Campbell; D. Donato; D. Azuma; B. Law

2007-01-01

We used a ground-based approach to compute the pyrogenic carbon emissions from the Biscuit Fire, an exceptionally large wildfire, which in 2002 burned over 200,000 ha of mixed conifer forest in southwestern Oregon. A combination of federal inventory data and supplementary ground measurements afforded the estimation of preburn densities for 25 separate carbon pools at...

Quality of Colonoscopy Performed in Rural Practice: Experience From the Clinical Outcomes Research Initiative and the Oregon Rural Practice-Based Research Network.

Science.gov (United States)

Holub, Jennifer L; Morris, Cynthia; Fagnan, Lyle J; Logan, Judith R; Michaels, LeAnn C; Lieberman, David A

2018-02-01

Colon cancer screening is effective. To complete screening in 80% of individuals over age 50 years by 2018 will require adequate colonoscopy capacity throughout the country, including rural areas, where colonoscopy providers may have less specialized training. Our aim was to study the quality of colonoscopy in rural settings. The Clinical Outcomes Research Initiative (CORI) and the Oregon Rural Practice-based Research Network (ORPRN) collaborated to recruit Oregon rural practices to submit colonoscopy reports to CORI's National Endoscopic Database (NED). Ten ORPRN sites were compared to non-ORPRN rural (n = 11) and nonrural (n = 43) sites between January 2009 and October 2011. Established colonoscopy quality measures were calculated for all sites. No ORPRN physicians were gastroenterologists compared with 82% of nonrural physicians. ORPRN practices reached the cecum in 87.4% of exams compared with 89.3% of rural sites (P = .0002) and 90.9% of nonrural sites (P 9mm 16.6% vs 18.7% (P = .106). ORPRN sites performed well on most colonoscopy quality measures, suggesting that high-quality colonoscopy can be performed in rural settings. © 2016 National Rural Health Association.

76 FR 80747 - Approval and Promulgation of Implementation Plans; Oregon: New Source Review/Prevention of...

Science.gov (United States)

2011-12-27

..., Definitions; Rule 0300, Excess Emissions and Emergency Provision, Purpose and Applicability; Rule 0310, Excess... GHG emissions under Oregon's NSR/PSD program. Oregon's definition of ``federal major source'' is almost identical to EPA's definition of ``major stationary source'' and as such, Oregon has tailored its...

D90: The Strongest Contributor to Setting Time in Mineral Trioxide Aggregate and Portland Cement.

Science.gov (United States)

Ha, William N; Bentz, Dale P; Kahler, Bill; Walsh, Laurence J

2015-07-01

The setting times of commercial mineral trioxide aggregate (MTA) and Portland cements vary. It was hypothesized that much of this variation was caused by differences in particle size distribution. Two gram samples from 11 MTA-type cements were analyzed by laser diffraction to determine their particle size distributions characterized by their percentile equivalent diameters (the 10th percentile, the median, and the 90th percentile [d90], respectively). Setting time data were received from manufacturers who performed indentation setting time tests as specified by the standards relevant to dentistry, ISO 6786 (9 respondents) or ISO 9917.1 (1 respondent), or not divulged to the authors (1 respondent). In a parallel experiment, 6 samples of different size graded Portland cements were produced using the same cement clinker. The measurement of setting time for Portland cement pastes was performed using American Society for Testing and Materials C 191. Cumulative heat release was measured using isothermal calorimetry to assess the reactions occurring during the setting of these pastes. In all experiments, linear correlations were assessed between setting times, heat release, and the 3 particle size parameters. Particle size varied considerably among MTA cements. For MTA cements, d90 was the particle size characteristic showing the highest positive linear correlation with setting time (r = 0.538). For Portland cement, d90 gave an even higher linear correlation for the initial setting time (r = 0.804) and the final setting time (r = 0.873) and exhibited a strong negative linear correlation for cumulative heat release (r = 0.901). Smaller particle sizes result in faster setting times, with d90 (the largest particles) being most closely correlated with the setting times of the samples. Copyright © 2015 American Association of Endodontists. All rights reserved.

Prediction of water vapour sorption isotherms and microstructure of hardened Portland cement pastes

International Nuclear Information System (INIS)

Burgh, James M. de; Foster, Stephen J.; Valipour, Hamid R.

2016-01-01

Water vapour sorption isotherms of cementitious materials reflect the multi-scale physical microstructure through its interaction with moisture. Our ability to understand and predict adsorption and desorption behaviour is essential in the application of modern performance-based approaches to durability analysis, along with many other areas of hygro-mechanical and hygro-chemo-mechanical behaviour. In this paper, a new physically based model for predicting water vapour sorption isotherms of arbitrary hardened Portland cement pastes is presented. Established thermodynamic principles, applied to a microstructure model that develops with hydration, provide a rational basis for predictions. Closed-form differentiable equations, along with a rational consideration of hysteresis and scanning phenomena, makes the model suitable for use in numerical moisture simulations. The microstructure model is reconciled with recently published 1 H NMR and mercury intrusion porosimetry results.

How to Use Current Medical Literature and APA Format Style.

Science.gov (United States)

Peek, Robin

Directives and guidance in obtaining current medical literature are provided in this publication with special emphasis given to locating material in the Portland, Oregon area. The uses and types of periodical indexes are identified and periodical index citation examples are indicated. Explanations are offered on: (1) how to conduct an effective…

Revealing the Experience of Children and Teachers Even in Their Absence: Documenting in the Early Childhood Studio

Science.gov (United States)

Parnell, Will

2011-01-01

Inspired by the educational approach in the municipal pre-primary schools and infant-toddler centers of Reggio Emilia, Italy, two studio teachers and a researcher participant in Portland, Oregon capture classroom work, make investigations and interpretations in the studio as a laboratory space of learning, help children represent thinking, and…

Portland cement for SO.sub.2 control in coal-fired power plants

Science.gov (United States)

Steinberg, Meyer

1985-01-01

There is described a method of removing oxides of sulfur from the emissions of fossil fuel combustion by injecting portland cement into the boiler with the fuel, the combustion air, or downstream with the combustion gases. There is also described the cement products that result from this method.

Portland cement for SO/sub 2/ control in coal-fired power plants

Science.gov (United States)

Steinberg, M.

1984-10-17

A method is described for removing oxides of sulfur from the emissions of fossil fuel combustion by injecting portland cement into the boiler with the fuel, the combustion air, or downstream with the combustion gases. The cement products that result from this method is also described. 1 tab.

Central Oregon 6 arc-second DEM

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The 6-second Central Coastal Oregon Elevation Grid provides bathymetric data in ASCII raster format of 6-second resolution in geographic coordinates. This grid is...

Northern Oregon 6 arc-second DEM

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The 6-second North Coast Oregon Elevation Grid provides bathymetric data in ASCII raster format of 6-second resolution in geographic coordinates. This grid is...

Influence Of Cement Kiln Dust As Partial Replacement On Some Properties Of Ordinary And White Portland Cement

Directory of Open Access Journals (Sweden)

Salah Sharif

2013-04-01

Full Text Available Cement Kiln Dust (CKD is produced as a solid waste with large quantities during manufacturing of Portland cement clinker. The possibility of utilizing CKD as partial replacement for Ordinary Portland Cement (OPC and White Portland Cement (WPC produced in factories of the Iraqi cement state company has been examined in this study to fulfil the environmental and economical aims. Different percentages of CKD were blended with OPC and WPC mixes. The results show that the amount of water for normal consistency were increased with about 39 % and 31 % for OPC and WPC blended with 25 % CKD. The setting time (initial and final decreases with increasing percent of CKD added. Compressive strength decreases slightly with increasing CKD content up to 10 %. For 7- day curing time, it decreases 7 % and 9 % for OPC and WPC mixes, respectively. As percent of added CKD increases to more than 10 %, the compressive strength and other parameters where affected significantly. Overall results proved that OPC and WPC blended with up to 10 % CKD are admissible for passing relevant specification requirements.

Stabilization/solidification of selenium-impacted soils using Portland cement and cement kiln dust

International Nuclear Information System (INIS)

Moon, Deok Hyun; Grubb, Dennis G.; Reilly, Trevor L.

2009-01-01

Stabilization/solidification (S/S) processes were utilized to immobilize selenium (Se) as selenite (SeO 3 2- ) and selenate (SeO 4 2- ). Artificially contaminated soils were prepared by individually spiking kaolinite, montmorillonite and dredged material (DM; an organic silt) with 1000 mg/kg of each selenium compound. After mellowing for 7 days, the Se-impacted soils were each stabilized with 5, 10 and 15% Type I/II Portland cement (P) and cement kiln dust (C) and then were cured for 7 and 28 days. The toxicity characteristic leaching procedure (TCLP) was used to evaluate the effectiveness of the S/S treatments. At 28 days curing, P doses of 10 and 15% produced five out of six TCLP-Se(IV) concentrations below 10 mg/L, whereas only the 15% C in DM had a TCLP-Se(IV) concentration 3 .H 2 O) and selenate substituted ettringite (Ca 6 Al 2 (SeO 4 ) 3 (OH) 12 .26H 2 O), respectively.

Use of interactive multimedia disks in the applied environmental sciences program at the Oregon Institute of Technology

Science.gov (United States)

Jones, Charles R.

Although a number of studies have been performed regarding the use of interactive multimedia disks in education, none were found which investigated their effect on either retention or recruitment for universities. The purpose of this case study was to gather information regarding student and teacher perceptions on the use of interactive multimedia disks and their effect on retention and recruitment. The primary source of data for this case study was student and teacher interviews. A purposive sample of students taking courses using the interactive multimedia disks in course at the Oregon Institute of Technology and at two Oregon high schools was chosen for the case study. Major findings of the case study were as follows: (1) Students interviewed in this case study perceived the interactive multimedia disk-based instructional method to be equally as effective as the lecture method. (2) Time flexibility in class scheduling was slightly more beneficial to female students than male students and the lack of instructor-led classroom interaction was more of a problem for female students than male students. (3) There was no difference in the perceptions of the college students and the high school students regarding the benefits and drawbacks of the interactive multimedia disk-based classes. (4) The flexible class scheduling made possible through the use of interactive multimedia disks influences some Oregon Institute of Technology students to stay and complete their degree programs. (5) There is some potential for interactive multimedia disk-based courses to be a recruiting tool. However, there is no evidence that it has been a successful recruiting tool for the Oregon Institute of Technology yet.

Effect of Nanosilica on the Fresh Properties of Cement-Based Grouting Material in the Portland-Sulphoaluminate Composite System

Directory of Open Access Journals (Sweden)

Shengli Li

2016-01-01

Full Text Available The effect of NS particle size and content on the fresh properties of the grouting material based on the portland-sulphoaluminate composite system was analyzed. The experimental results indicated that air content increased and apparent density decreased, with increased NS content, but the NS particle sizes have minimal effect on the air content and apparent density. The setting time of mortar was significantly shortened, with increased NS content; however, NS particle sizes had little influence on the setting time. The effect of fluidity on the mortars adding NS with particle size of 30 nm is larger than NS with particle sizes of 15 and 50 nm and the fluidity decreased with increased NS content, but the fluidity of mortars with the particle sizes of 15 and 50 nm is almost not affected by the NS content. XRD analysis shows that the formation of ettringite was promoted and the process of hydration reaction of cement was accelerated with the addition of NS. At the microscopic level, the interfacial transition zone (ITZ of the grouting material became denser and the formation of C-S-H gel was promoted after adding NS.

Seaside, Oregon, Tsunami Vulnerability Assessment Pilot Study

Science.gov (United States)

Dunbar, P. K.; Dominey-Howes, D.; Varner, J.

2006-12-01

The results of a pilot study to assess the risk from tsunamis for the Seaside-Gearhart, Oregon region will be presented. To determine the risk from tsunamis, it is first necessary to establish the hazard or probability that a tsunami of a particular magnitude will occur within a certain period of time. Tsunami inundation maps that provide 100-year and 500-year probabilistic tsunami wave height contours for the Seaside-Gearhart, Oregon, region were developed as part of an interagency Tsunami Pilot Study(1). These maps provided the probability of the tsunami hazard. The next step in determining risk is to determine the vulnerability or degree of loss resulting from the occurrence of tsunamis due to exposure and fragility. The tsunami vulnerability assessment methodology used in this study was developed by M. Papathoma and others(2). This model incorporates multiple factors (e.g. parameters related to the natural and built environments and socio-demographics) that contribute to tsunami vulnerability. Data provided with FEMA's HAZUS loss estimation software and Clatsop County, Oregon, tax assessment data were used as input to the model. The results, presented within a geographic information system, reveal the percentage of buildings in need of reinforcement and the population density in different inundation depth zones. These results can be used for tsunami mitigation, local planning, and for determining post-tsunami disaster response by emergency services. (1)Tsunami Pilot Study Working Group, Seaside, Oregon Tsunami Pilot Study--Modernization of FEMA Flood Hazard Maps, Joint NOAA/USGS/FEMA Special Report, U.S. National Oceanic and Atmospheric Administration, U.S. Geological Survey, U.S. Federal Emergency Management Agency, 2006, Final Draft. (2)Papathoma, M., D. Dominey-Howes, D.,Y. Zong, D. Smith, Assessing Tsunami Vulnerability, an example from Herakleio, Crete, Natural Hazards and Earth System Sciences, Vol. 3, 2003, p. 377-389.

Hydration kinetics for the alite, belite, and calcium aluminate phase in Portland cements from 27Al and 29Si MAS NMR spectroscopy

DEFF Research Database (Denmark)

Skibsted, Jørgen; Jensen, Ole Mejlhede; Jakobsen, Hans Jørgen

1997-01-01

29Si magic-angle spinning (MAS) NMR spectroscopy is shown to be a valuable tool for obtaining the quantities of alite and belite in hydrated Portland cements. The hydration (1-180 days) of a white Portland cement with 10 wt.% silica fume added is investigated and the degrees of hydration for alite...

33 CFR 165.1316 - Safety Zone; Columbia River, Astoria, Oregon.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety Zone; Columbia River....1316 Safety Zone; Columbia River, Astoria, Oregon. (a) Location. The following area is a safety zone... Oregon shoreline at 123°49′36″ West to 46°11′51″ North thence east to 123°48′53″ West thence south to the...

Rasch measurement analysis of the Mayo-Portland Adaptability Inventory (MPAI-4) in a community-based rehabilitation sample.

Science.gov (United States)

Kean, Jacob; Malec, James F; Altman, Irwin M; Swick, Shannon

2011-05-01

The precise measurement of patient outcomes depends upon clearly articulated constructs and refined clinical assessment instruments that work equally well for all subgroups within a population. This is a challenging task in those with acquired brain injury (ABI) because of the marked heterogeneity of the disorder and subsequent outcomes. Although essential, the iterative process of instrument refinement is often neglected. This present study was undertaken to examine validity, reliability, dimensionality and item estimate invariance of the Mayo-Portland Adaptability Inventory - 4 (MPAI-4), an outcome measure for persons with ABI. The sampled population included 603 persons with traumatic ABI participating in a home- and community-based rehabilitation program. Results indicated that the MPAI-4 is a valid, reliable measure of outcome following traumatic ABI, which measures a broad but unitary core construct of outcome after ABI. Further, the MPAI-4 is composed of items that are unbiased toward selected subgroups except where differences could be expected [e.g., more chronic traumatic brain injury (TBI) patients are better able to negotiate demands of transportation than more acute TBI patients]. We address the trade-offs between strict unidimensionality and clinical applicability in measuring outcome, and illustrate the advantages and disadvantages of applying single-parameter measurement models to broad constructs.

The biomineralization ability of mineral trioxide aggregate and Portland cement on dentin enhances the push-out strength.

Science.gov (United States)

Reyes-Carmona, Jessie F; Felippe, Mara S; Felippe, Wilson T

2010-02-01

Recently, it was shown that the interaction of each of mineral trioxide aggregate (MTA) and Portland cement with dentin in phosphate-buffered saline (PBS) promotes a biomineralization process that leads to the formation of an interfacial layer with tag-like structures at the cement-dentin interface. This study analyzes the influence of the biomineralization process on the push-out strength of ProRoot MTA (Dentsply Tulsa Dental, Tulsa, OK), MTA Branco (Angelus Soluções Odontológicas, Londrina, PR, Brazil), MTA BIO (Angelus Soluções Odontológicas), or Portland cement with and without calcium chloride. Dentin discs with standardized cavities were filled with ProRoot MTA, MTA Branco, MTA BIO, white Portland cement + 20% bismuth oxide (PC1), or PC1 + 10% of calcium chloride (PC2). The specimens were randomly divided into two groups: cement in contact with a wet cotton pellet for 72 hours or immersed in PBS for 2 months. The bond strengths were measured with the Instron Testing machine (Model 4444; Instron Corp, Canton, MA), and the fractured surfaces on the root walls were observed by scanning electron microscopy. All samples immersed in PBS displayed a significantly greater resistance to displacement than that observed for the samples in contact with a wet cotton pellet for 72 hours (p Portland cements. It was concluded that the biomineralization process positively influenced the push-out bond strength of the cements, particularly the MTA groups. Copyright 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Experimental investigation of the multiple scatter peak of gamma rays in portland cement in the energy range 279-1332 keV

International Nuclear Information System (INIS)

Singh, Tejbir; Singh, Parjit S

2011-01-01

The pulse height spectra for different thicknesses of portland cement in the reflected geometry has been recorded with the help of a NaI(Tl) scintillator detector and 2 K MCA card using different gamma-ray sources such as Hg 203 (279 keV), Cs 137 (662 keV) and Co 60 (1173 and 1332 keV). It has been observed that the multiple scatter peak for portland cement appears at 110 (±7) keV in all the spectra irrespective of different incident photon energies in the range 279-1332 keV from different gamma-ray sources. Further, the variation in the intensity of the multiple scatter peak with the thickness of portland cement in the backward semi-cylinders has been investigated.

Red alder kitchen cabinets—How does application of commercial stains influence customer choice?

Science.gov (United States)

David Nicholls; Joseph. Roos

2007-01-01

A better understanding of consumer reaction and preferences for red alder (Alnus rubra Bong.) secondary products will help Alaska producers in entering new markets. In this study, red alder kitchen cabinets were commercially stained to six different levels and displayed at home shows in Portland, Oregon, and Anchorage, Alaska. The stains simulated...

Districts Neglecting Programs for ELLs

Science.gov (United States)

Zehr, Mary Ann

2010-01-01

The author reports on state and independent reviews that cite shortcomings in four urban systems. According to the reviews of those school systems over the past two years, four urban districts--in Boston, Massachusetts; Buffalo, New York; Portland, Oregon; and Seattle, Washington--did not provide special help to learn English to all students…

XRF analysis of portland cement for major and trace elements

International Nuclear Information System (INIS)

Abdunnabi, A. R.

2012-12-01

Libyan portland cement produced in several factories around the country, in Lip tis, Zoltan, Souq-Elkamis, Dernah and El-Fatach, were analyzed for quantitative major and trace elements and mineral content, which were compered with those imported from Spain, Romania, Cyprus, and Egypt. X-ray fluorescence spectro X lab 2000 spectrometer equipped with Rh-and X-ray tube was used for the analysis of various samples. The detector Si(Li) with a resolution of 148 eV at Mn K-a=5.9 keV facilitates the determination of a wide range of elements from sodium to uranium, with a detection limit at sub levels. Cement samples in the powder form were analyzed using the pellet-technique. The pellets were prepared by mixing 4g of the cement powder with 0.9 g of binder (HWC) and pressed at high pressure. A ful analysis including, background counting, matrix correction and all relevant corrections were achieved automatically by XLAB 2000 software package. For major and trace elements X RF results were higher for most of the elements than those analyzed with atomic absorption spectrometry. The mineral content showed that Libyan cement is comparable to the imported ones, also the Libyan cement meets the requirements of the international specifications of the portland cement. (Author)

A Histologic Evaluation on Tissue Reaction to Three Implanted Materials (MTA, Root MTA and Portland Cement Type I in the Mandible of Cats

Directory of Open Access Journals (Sweden)

F. Sasani

2004-09-01

Full Text Available Statement of Problem: Nowadays Mineral Trioxide aggregate (MTA is widely used for root end fillings, pulp capping, perforation repair and other endodontic treatments.Investigations have shown similar physical and chemical properties for Portland cement and Root MTA with those described for MTA.Purpose: The aim of this in vitro study was to evaluate the tissue reaction to implanted MTA, Portland cement and Root MTA in the mandible of cats.Materials and Methods: Under asepsis condition and general anesthesia, a mucoperiosteal flap, following the application of local anesthesia, was elevated to expose mandibular symphysis. Two small holes in both sides of mandible were drilled. MTA, Portland cement and Root MTA were mixed according to the manufacturers, recommendation and placed in bony cavities. In positive control group, the test material was Zinc oxide powder plus tricresoformalin. In negative control group, the bony cavities were left untreated. After 3,6 and 12 weeks, the animals were sacrificed and the mandibular sections were prepared for histologic examination under light microscope. The presence and thickness of inflammation, presence of fibrosis capsule, the severity of fibrosis and bone formation were investigated. The data were submitted to Exact Fisher test, chi square test and Kruskal-Wallis test for statistical analysis.Results: No statistically significant differences were found in the degree of inflammation,presence of fibrotic capsule, severity of fibrosis and inflammation thickness between Root MTA, Portland cement and MTA (P>0.05. There was no statistical difference in boneformation between MTA and Portland cement (P>0.05. However, bone formation was not found in any of the Root MTA specimens and the observed tissue was exclusively of fibrosis type.Conclusion: The physical and histological results observed with MTA are similar to those of Root MTA and Portland cement. Additionally, all of these three materials are biocompatible

Determination of coefficient of thermal expansion for Portland Cement Concrete pavements for MEPDG Implementation

Science.gov (United States)

2012-10-01

The Coefficient of Thermal Expansion (CTE) is an important parameter in Portland Cement Concrete (PCC) pavement analysis and design as it is directly proportional to the magnitude of temperature-related pavement deformations throughout the pavement s...

Root morphology and growth of bare-root seedlings of Oregon white oak

Science.gov (United States)

Peter J. Gould; Constance A. Harrington

2009-01-01

Root morphology and stem size were evaluated as predictors of height and basal-area growth (measured at groundline) of 1-1 Oregon white oak (Quercus garryana Dougl. ex Hook.) seedlings planted in raised beds with or without an additional irrigation treatment. Seedlings were classified into three root classes based on a visual assessment of the...

Assessment the potential of using Carbon nanotubes reinforcements for improving the tensile/flexural strength and fracture toughness of Portland cement paste for damage resistant concrete transportation infrastructures.

Science.gov (United States)

2010-09-01

The focus of this study was on exploring the use of nanotechnology-based nano-filaments, such as carbon : nanotubes (CNTs) and nanofibers (CNFs), as reinforcement in improving the mechanical properties of Portland : cement paste as a construction mat...

In Vitro Bioactivity and Setting Times of White Portland Cement Combined with Different Radio Pacifying Agents

Directory of Open Access Journals (Sweden)

Coleman Nichola Jayne

2017-01-01

Full Text Available Commercial formulations based on 80:20 mixtures of Portland cement and bismuth oxide (a radiopacifying agent are used in dentistry as root-filling materials. This study compares the impact of two alternative radiopacifiers, barium sulphate and zirconium oxide, with that of bismuth oxide, on the setting times and bioactivity of white Portland cement. The findings indicate that bismuth oxide prolongs both the initial and final setting times of the cement, and that barium sulphate and zirconium oxide have no effect on this parameter. Hydroxyapatite (HA formed on the surfaces of all test samples within 7 days of exposure to simulated body fluid, indicating that they possess the potential to stimulate new hard tissue formation. Fourier transform infrared spectroscopy, the traditional technique for the identification of HA, was not appropriate for the analysis of these cement systems owing to the overlap of signals from each of the radiopacifiers with the characteristic P-O bending modes of HA in the 570 – 610 cm−1 region. In this respect, the P-O band at 965 cm−1 of HA in the Raman spectrum was found to be a suitable means of detection since it is discrete with respect to all signals arising from the radiopacifying agents and cement phases.

The influence of shrinkage-cracking on the drying behaviour of White Portland cement using Single-Point Imaging (SPI).

Science.gov (United States)

Beyea, S D; Balcom, B J; Bremner, T W; Prado, P J; Cross, A R; Armstrong, R L; Grattan-Bellew, P E

1998-11-01

The removal of water from pores in hardened cement paste smaller than 50 nm results in cracking of the cement matrix due to the tensile stresses induced by drying shrinkage. Cracks in the matrix fundamentally alter the permeability of the material, and therefore directly affect the drying behaviour. Using Single-Point Imaging (SPI), we obtain one-dimensional moisture profiles of hydrated White Portland cement cylinders as a function of drying time. The drying behaviour of White Portland cement, is distinctly different from the drying behaviour of related concrete materials containing aggregates.

Characterizing Process-Based River and Floodplain Restoration Projects on Federal Lands in Oregon, and Assessing Catalysts and Barriers to Implementation

Science.gov (United States)

Bianco, S.; Jones, J. A.; Gosnell, H.

2017-12-01

Process-based restoration, a new approach to river and floodplain management, is being implemented on federal lands across Oregon. These management efforts are aimed at promoting key physical processes in order to improve river ecological function, create diverse habitat, and increase biological productivity for ESA-listed bull trout and spring Chinook salmon. Although the practice is being disseminated across the Pacific Northwest, it remains unclear what is driving aquatic and riparian ecosystem restoration towards this process-based approach and away from form-based methods such as Rosgen's Natural Channel Design. The technical aspects of process-based restoration have been described in the literature (ex. Beechie et al. 2010), but little is known about the practice from a social science perspective, and few case studies exist to assess the impact of these efforts. We combine semi-structured qualitative interviews with management experts and photogrammetric analysis to better understand how complex social processes and changing ideas about aquatic ecosystems are manifesting on the ground in federal land management. This study characterizes process-based river and floodplain restoration projects on federal lands in Oregon, and identifies catalysts and barriers to its implementation. The Deer Creek Floodplain Enhancement project serves as a case study for photogrammetric analysis. To characterize long-term changes at Deer Creek, geomorphic features were mapped and classified using orthoimage mosaics developed from a time series of historic aerial photographs dating back to 1954. 3D Digital Elevation Models (3D-DEMs) were created of portions of the modified sections of Deer Creek and its floodplain immediately before and after restoration using drone-captured aerial photography and a photogrammetric technique called Structure from Motion. These 3D-DEMs have enabled extraction of first-order geomorphic variables to compare pre- and post-project conditions. This

Effects of questionnaire-based diagnosis and training on inter-rater reliability among practitioners of traditional Chinese medicine.

Science.gov (United States)

Mist, Scott; Ritenbaugh, Cheryl; Aickin, Mikel

2009-07-01

To investigate whether a training process that focused on a questionnaire-based diagnosis in Traditional Chinese Medicine (TCM), and developing diagnostic consensus, would improve the agreement of TCM diagnoses among 10 TCM practitioners evaluating patients with temporomandibular joint disorder (TMJD). Evaluation of a diagnostic training program at the Department of Family and Community Medicine, University of Arizona, Tucson, Arizona, and the Oregon College of Oriental Medicine, Portland, Oregon. Screened participants for a study of TCM for TMJD. PRACTITIONERS: Ten (10) licensed acupuncturists with a minimum of 5 years licensure and education in Chinese herbs. A training session using a questionnaire-based diagnostic form was conducted, followed by waves of diagnostic sessions. Between sessions, practitioners discussed the results of the previous round of participants with a focus on reducing variability in primary diagnosis and severity rating of each diagnosis: 3 waves of 5 patients were assessed by 4 practitioner pairs for a total of 120 diagnoses. At 18 months, practitioners completed a recalibration exercise with a similar format with a total of 32 diagnoses. These diagnoses were then examined with respect to the rate of agreement among the 10 practitioners using inter-rater correlations and kappas. The inter-rater correlation with respect to the TCM diagnoses among the 10 practitioners increased from 0.112 to 0.618 with training. Statistically significant improvements were found between the baseline and 18 month exercises (p reliability of TCM diagnosis may be improved through a training process and a questionnaire-based diagnosis process. The improvements varied by diagnosis, with the greatest congruence among primary and more severe diagnoses. Future TCM studies should consider including calibration training to improve the validity of results.

Developing Biomass Equations for Western Hemlock and Red Alder Trees in Western Oregon Forests

Science.gov (United States)

Krishna Poudel; Hailemariam Temesgen

2016-01-01

Biomass estimates are required for reporting carbon, assessing feedstock availability, and assessing forest fire threat. We developed diameter- and height-based biomass equations for Western hemlock (Tsuga heterophylla (Raf.) Sarg.) and red alder (Alnus rubra Bong.) trees in Western Oregon. A system of component biomass...

Lichen ecology and diversity of a sagebrush steppe in Oregon: 1977 to the present

Science.gov (United States)

A lichen checklist is presented of 141 species from the Lawrence Memorial Grassland Preserve and nearby lands in Wasco County, Oregon, based on collections made in the 1970s and 1990s. Collections include epiphytic, lignicolous, saxicolous, muscicolous and terricolous species. To evaluate differenc...

Study irradiation damage by fast neutrons in Portland cement by means of ultra-sound

International Nuclear Information System (INIS)

Rosa Junior, A.A.

1988-01-01

The effect of neutron irradiation in samples of Portland cement paste was evaluated, using the resonance frequency method and pulse velocity of ultra-sound technique. The samples were divide in three groups: 1) Monitoring samples; 2) Samples to gamma heating simulation; 3) Fast neutron irradiated samples in reactor core. Santa Rita Portland cement was utilized for samples preparation with water-cement rate of 0,40 l/kg. The irradiation was performed in the research reactor IEA-R1, at IPEN-CNEN/SP, with an integrated flux of 7,2 X 10 sup(18) n/cm sup(2) (E approx. 1 Mev). The samples of group 2 were submitted to special micro-waves heat treatment-with the same number of cycles of the reactor-which allowed the detection of fast neutron radiation effects within the predominant thermal effects. (author)

Characterization of Fish Passage Conditions through a Francis Turbine, Spillway, and Regulating Outlet at Detroit Dam, Oregon, Using Sensor Fish, 2009

Energy Technology Data Exchange (ETDEWEB)

Duncan, Joanne P.; Carlson, Thomas J.

2011-05-06

Fish passage conditions through two spillways, a Francis turbine, and a regulating outlet (RO) at Detroit Dam on the North Santiam River in Oregon were evaluated by Pacific Northwest National Laboratory for the U.S. Army Corps of Engineers (USACE), Portland District, using Sensor Fish devices. The objective of the study was to describe and compare passage exposure conditions, identifying potential fish injury regions within the routes. The study was performed in July, October, and December 2009 concurrent with HI-Z balloon-tag studies by Normandeau Associates, Inc. Sensor Fish data were analyzed to estimate 1) exposure conditions, particularly exposure to severe strike, collision, and shear events by passage route sub-regions; 2) differences in passage conditions between passage routes; and 3) relationships to live-fish injury and mortality data estimates. Comparison of the three passage routes evaluated at Detroit Dam indicates that the RO passage route through the 5-ft gate opening was relatively the safest route for fish passage under the operating conditions tested; turbine passage was the most deleterious. These observations were supported also by the survival and malady estimates obtained from live-fish testing. Injury rates were highest for turbine and spillway passage. However, none of the passage routes tested is safe for juvenile salmonid passage.

Bioactive coatings on Portland cement substrates: Surface precipitation of apatite-like crystals

International Nuclear Information System (INIS)

Gallego, Daniel; Higuita, Natalia; Garcia, Felipe; Ferrell, Nicholas; Hansford, Derek J.

2008-01-01

We report a method for depositing bioactive coatings onto cement materials for bone tissue engineering applications. White Portland cement substrates were hydrated under a 20% CO 2 atmosphere, allowing the formation of CaCO 3 . The substrates were incubated in a calcium phosphate solution for 1, 3, and 6 days (CPI, CPII, and CPIII respectively) at 37 deg. C to induce the formation of carbonated apatite. Cement controls were prepared and hydrated with and without CO 2 atmosphere (C+ and C- respectively). The presence of apatite-like crystals was verified by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS). The substrate cytocompatibility was evaluated via SEM after 24 hour cell cultures. SEM revealed the presence Ca(OH) 2 on C-, and CaCO 3 on C+. Apatite-like crystals were detected only on CPIII, confirmed by phosphorus EDS peaks only for CPIII. Cells attached and proliferated similarly well on all the substrates except C-. These results prove the feasibility of obtaining biocompatible and bioactive coatings on Portland cement for bone tissue engineering applications

Portland cement with additives in the repair of furcation perforations in dogs.

Science.gov (United States)

Silva Neto, José Dias da; Schnaider, Taylor Brandão; Gragnani, Alfredo; Paiva, Anderson Paulo de; Novo, Neil Ferreira; Ferreira, Lydia Masako

2012-11-01

To evaluate the use of Portland cements with additives as furcation perforation repair materials and assess their biocompatibility. The four maxillary and mandibular premolars of ten male mongrel dogs (1-1.5 years old, weighing 10-15 kg) received endodontic treatment (n=80 teeth). The furcations were perforated with a round diamond bur (1016 HL). The perforations involved the dentin, cementum, periodontal ligament, and alveolar bone. A calcium sulfate barrier was placed into the perforated bone to prevent extrusion of obturation material into the periradicular space. The obturation materials MTA (control), white, Type II, and Type V Portland cements were randomly allocated to the teeth. Treated teeth were restored with composite resin. After 120 days, the animals were sacrificed and samples containing the teeth were collected and prepared for histological analysis. There were no significant differences in the amount of newly formed bone between teeth treated with the different obturation materials (p=0.879). Biomineralization occurred for all obturation materials tested, suggesting that these materials have similar biocompatibility.

Effect of radiopaque Portland cement on mineralization in human dental pulp cells.

Science.gov (United States)

Min, Kyung-San; Lee, Sang-Im; Lee, Yoon; Kim, Eun-Cheol

2009-10-01

The aim of this study was to investigate whether radiopaque Portland cement (RPC) facilitates the mineralization process in human dental pulp cells (HDPCs) compared with pure Portland cement (PC). Under a scanning electron microscope (SEM), cellular morphology was evaluated. Alkaline phosphatase (ALP) activity was analyzed, and nodule formation was assessed by performing Alizarin Red S staining. In addition, the mRNA expressions of mineralization-related proteins were evaluated by performing a real-time polymerase chain reaction. On SEM evaluation, healthy HDPCs were found adhering to the surfaces of PC and RPC. The ALP activity increased in the PC and RPC groups compared with the control group at 1 day. Alizarin Red stain increased in the PC and RPC groups compared with the control group at 2 and 3 weeks. The mRNA expression of dentin sialophosphoprotein increased at 14 days in the PC and RPC groups. These results show that PC and RPC have similar effects in terms of mineralization and suggest that RPC also has the potential to be used as a clinically suitable pulp-capping material.

Overview for geologic field-trip guides to volcanoes of the Cascades Arc in northern California

Science.gov (United States)

Muffler, L. J. Patrick; Donnelly-Nolan, Julie M.; Grove, Timothy L.; Clynne, Michael A.; Christiansen, Robert L.; Calvert, Andrew T.; Ryan-Davis, Juliet

2017-08-15

The California Cascades field trip is a loop beginning and ending in Portland, Oregon. The route of day 1 goes eastward across the Cascades just south of Mount Hood, travels south along the east side of the Cascades for an overview of the central Oregon volcanoes (including Three Sisters and Newberry Volcano), and ends at Klamath Falls, Oregon. Day 2 and much of day 3 focus on Medicine Lake Volcano. The latter part of day 3 consists of a drive south across the Pit River into the Hat Creek Valley and then clockwise around Lassen Volcanic Center to the town of Chester, California. Day 4 goes from south to north across Lassen Volcanic Center, ending at Burney, California. Day 5 and the first part of day 6 follow a clockwise route around Mount Shasta. The trip returns to Portland on the latter part of day 6, west of the Cascades through the Klamath Mountains and the Willamette Valley. Each of the three sections of this guidebook addresses one of the major volcanic regions: Lassen Volcanic Center (a volcanic field that spans the volcanic arc), Mount Shasta (a fore-arc stratocone), and Medicine Lake Volcano (a rear-arc, shield-shaped edifice). Each section of the guide provides (1) an overview of the extensive field and laboratory studies, (2) an introduction to the literature, and (3) directions to the most important and accessible field localities. The field-trip sections contain far more stops than can possibly be visited in the actual 6-day 2017 IAVCEI excursion from Portland. We have included extra stops in order to provide a field-trip guide that will have lasting utility for those who may have more time or may want to emphasize one particular volcanic area.

Characterization of floodflows along the Arkansas River without regulation by Pueblo Reservoir, Portland to John Martin Reservoir, Southeastern Colorado

Science.gov (United States)

Little, John R.; Bauer, Daniel P.

1981-01-01

The need for a method for estimating flow characteristics of flood hydrographs between Portland, Colo., and John Martin Reservoir has been promoted with the construction of the Pueble Reservoir. To meet this need a procedure was developed for predicting floodflow peaks, traveltimes, and volumes at any point along the Arkansas River between Portland and John Martin Reservoir without considering the existing Pueble Reservoir detention effects. A streamflow-routing model was calibrated initially and then typical flood simulations were made for the 164.8-mile study reach. Simulations were completed for varying magnitudes of floods and antecedent streamflow conditions. Multiple regression techniques were then used with simulation results as input to provide predictive relationships for food peak, volume, and traveltime. Management practices that may be used to benefit water users in the area include providing methods for the distribution and allotment of the flood waters upstream of Portland to different downstream water users according to Colorado water law and also under the Arkansas River Compact. (USGS)

Description of the structural evolution of a hydrating portland cement paste by SANS

International Nuclear Information System (INIS)

Haeussler, F.; Eichhorn, F.; Baumbach, H.

1994-01-01

On the spectrometer MURN at the pulsed reactor IBR-2 dry Portland cement, silica fume, and a hydrating Portland cement paste were studied by small-angle neutron scattering (SANS). By using the TOF-method a momentum transfer from 0.07 nm -1 to 7 nm -1 is detectable. Every component (dry cement powder, clinker minerals, hydrating cement pastes) shows a different scattering behaviour. In the measured Q-region the hardening cement paste does not show a Porod-like behaviour of SANS-curves. In contrast the Porod's potential law holds for dry powder samples of clinker minerals and silica fume. In experiments carried out to observe the hydration progress within the first 321 days the characteristics of the scattering curves (potential behaviour, the radius of gyration, and the macroscopic scattering cross section at Q = 0 nm -1 were measured. Some evolution of the inner structure of the hardened cement paste was noted. (orig.)

Design and manufacture of Portland cement - application of sensitivity analysis in exploration and optimisation Part II. Optimisation

DEFF Research Database (Denmark)

Svinning, K.; Høskuldsson, Agnar

2006-01-01

A program for a model-based optimisation has been developed. The program contains two subprograms. The first one does minimising or maximising constrained by one original PLS-component or one equal to a combination of several. The second one does searching for the optimal combination of PLS-compo......-components, which gives max or min y. The program has proved to be applicable for achieving realistic results for implementation in the design of Portland cement with respect to performance and in the quality control during production....

Interview with Mike Shaughnessy

Science.gov (United States)

Rossman, Allan; Shaughnessy, Mike

2013-01-01

Mike Shaughnessy is Professor Emeritus of Mathematics and Statistics at Portland State University in Oregon. He served as co-chair for the Board for the Special Interest Group for Research in Mathematics Education of the American Educational Research Association from 2005-2007. A member of the Board of Directors of the National Council of Teachers…

"Don't Take Our Voices Away": A Role Play on the Indigenous Peoples' Global Summit on Climate Change

Science.gov (United States)

O'Neill, Julie Treick; Swinehart, Tim

2010-01-01

The Indigenous Peoples' Climate Summit role play grew out of the Portland Area Rethinking Schools Earth in Crisis Curriculum Workgroup and the Oregon Writing Project. It was designed to introduce students to the broad injustice of the climate crisis and to familiarize them with some of the specific issues faced by different indigenous groups…

An Examination of Embedding Character Education into the Daily Functions of High School Instrumental Music Ensembles

Science.gov (United States)

Sours, James P.

2009-01-01

This study was conducted to examine the effectiveness of embedding character education into the daily functions of instrumental music ensembles at Franklin High School in Portland Oregon. The participants in the study were the students of the researcher which may have been a delimitation. Their ages were from 14 to 19 years. Students from…

Right under Their Noses: Native Plants in the Schoolyard.

Science.gov (United States)

Reed, Bracken

2003-01-01

A Portland (Oregon) middle school teacher teaches an ethnobotany class using plants identified in Lewis and Clark's journals. After months of learning about native plants, Native American culture, and the Lewis and Clark Expedition, the class culminates in a 3-day canoe trip down the Columbia River. A Lewis and Clark Rediscovery grant provides…

Toward a defensible lynx conservation strategy: A framework for planning in the face of uncertainty [Chapter 1

Science.gov (United States)

Leonard F. Ruggiero; Kevin S. McKelvey

2000-01-01

On April 2, 1993, the incumbent U.S. President traveled to Portland, Oregon, to intervene in a national political crisis engendered by public concern over the conservation of native wildlife on public lands. Environmentalists had successfully used existing statutes, most notably the National Forest Management Act and pursuant regulations, to shut down timber industry...

Coastal subsidence in Oregon, USA during the giant Cascadia earthquake of AD 1700

Science.gov (United States)

Hawkes, A.D.; Horton, B.P.; Nelson, A.R.; Vane, C.H.; Sawai, Y.

2011-01-01

Quantitative estimates of land-level change during the giant AD 1700 Cascadia earthquake along the Oregon coast are inferred from relative sea-level changes reconstructed from fossil foraminiferal assemblages preserved within the stratigraphic record. A transfer function, based upon a regional training set of modern sediment samples from Oregon estuaries, is calibrated to fossil assemblages in sequences of samples across buried peat-mud and peat-sand contacts marking the AD 1700 earthquake. Reconstructions of sample elevations with sample-specific errors estimate the amount of coastal subsidence during the earthquake at six sites along 400 km of coast. The elevation estimates are supported by lithological, carbon isotope, and faunal tidal zonation data. Coseismic subsidence at Nehalem River, Nestucca River, Salmon River, Alsea Bay, Siuslaw River and South Slough varies between 0.18 m and 0.85 m with errors between 0.18 m and 0.32 m. These subsidence estimates are more precise, consistent, and generally lower than previous semi-quantitative estimates. Following earlier comparisons of semi-quantitative subsidence estimates with elastic dislocation models of megathrust rupture during great earthquakes, our lower estimates for central and northern Oregon are consistent with modeled rates of strain accumulation and amounts of slip on the subduction megathrust, and thus, with a magnitude of 9 for the AD 1700 earthquake.

Strategies for Addressing the Challenges of Patient-Centered Medical Home Implementation: Lessons from Oregon.

Science.gov (United States)

Gelmon, Sherril; Bouranis, Nicole; Sandberg, Billie; Petchel, Shauna

2018-01-01

Patient-centered medical homes (PCMHs) are at the forefront of the transformation of primary care as part of health systems reform. Despite robust literature describing implementation challenges, few studies describe strategies being used to overcome these challenges. This article addresses this gap through observations of exemplary PCMHs in Oregon, where the Oregon Health Authority supports and recognizes Patient-Centered Primary Care Homes (PCPCH). Twenty exemplary PCPCHs were selected using program scores, with considerations for diversity in clinic characteristics. Between 2015 and 2016, semistructured interviews and focus groups were completed with 85 key informants. Clinics reported similar challenges implementing the PCPCH model, including shifting patterns of care use, fidelity to the PCPCH model, and refining care processes. The following ten implementation strategies emerged: expanding access through care teams, preventing unnecessary emergency department visits through patient outreach, improved communication and referral tracking with outside providers, prioritization of selected program metrics, implementing patient-centered practices, developing continuous improvement capacity through committees and "champions," incorporating preventive services and chronic disease management, standardization of workflows, customizing electronic health records, and integration of mental health. Clinic leaders benefited from understanding the local context in which they were operating. Despite differences in size, ownership, geography, and population, all clinic leaders were observed to be proponents of strategies commonly associated with a "learning organization": systems thinking, personal mastery, mental models, shared vision, and team. Clinics can draw on their own characteristics, use state resources, and look to established PCMHs to build the evidence base for implementation in primary care. © Copyright 2018 by the American Board of Family Medicine.

Possibility of using waste tire rubber and fly ash with Portland cement as construction materials.

Science.gov (United States)

Yilmaz, Arin; Degirmenci, Nurhayat

2009-05-01

The growing amount of waste rubber produced from used tires has resulted in an environmental problem. Recycling waste tires has been widely studied for the last 20 years in applications such as asphalt pavement, waterproofing systems and membrane liners. The aim of this study is to evaluate the feasibility of utilizing fly ash and rubber waste with Portland cement as a composite material for masonry applications. Class C fly ash and waste automobile tires in three different sizes were used with Portland cement. Compressive and flexural strength, dry unit weight and water absorption tests were performed on the composite specimens containing waste tire rubber. The compressive strength decreased by increasing the rubber content while increased by increasing the fly ash content for all curing periods. This trend is slightly influenced by particle size. For flexural strength, the specimens with waste tire rubber showed higher values than the control mix probably due to the effect of rubber fibers. The dry unit weight of all specimens decreased with increasing rubber content, which can be explained by the low specific gravity of rubber particles. Water absorption decreased slightly with the increase in rubber particles size. These composite materials containing 10% Portland cement, 70% and 60% fly ash and 20% and 30% tire rubber particles have sufficient strength for masonry applications.

Characterization and chemical activity of Portland cement and two experimental cements with potential for use in dentistry.

Science.gov (United States)

Camilleri, J

2008-09-01

To evaluate the chemical activity of Portland cement and two other cement types with similar chemical composition to mineral trioxide aggregate with the aim of developing these cements for further applications in dentistry. The chemical composition of the three cement types namely Portland cement, calcium sulpho-aluminate cement and calcium fluoro-aluminate cement was evaluated by elemental analysis using energy dispersive analysis with X-ray under the scanning electron microscope and by X-ray diffraction analysis (XRD) to determine the phases. The constituents of the hydration reaction by-products were evaluated by XRD analysis of the set cements at 1, 7, 28 and 56 days and by analysis of the leachate by ion chromatography. The pH of both cements and leachate was determined at different time intervals. Cements admixed with micro-silica were also tested to determine the effect of micro-silica on the reaction by-products. All three cement types were composed of tricalcium silicate as the main constituent phase. The hydration reaction of Portland cement produced calcium hydroxide. However, this was not present in the other cements tested at all ages. Admixed micro-silica had little or no effect on the cements with regard to reaction by-products. The pH of all cements tested was alkaline. Both the experimental calcium sulpho-aluminate cement and calcium fluoro-aluminate cement had different hydration reactions to that of Portland cement even though calcium silicate was the major constituent element of both cement types. No calcium hydroxide was produced as a by-product to cement hydration. Micro-silica addition to the cement had no effect on the hydration reaction.

Resource partitioning among woodpeckers in northeastern Oregon.

Science.gov (United States)

Bull Evelyn L.; Steven R. Peterson; Jack Ward. Thomas

1986-01-01

Eight species of woodpeckers coexist in conifer forests in northeastern Oregon: northern flicker (Colaptes auratus); yellow-bellied (Sphyrapicus varius) and Williamson's (S. thyroideus) sapsuckers; and pileated (Dryocopus pileatus), hairy (Picoides villosus),...

Oregon State University TRIGA Reactor annual report

Energy Technology Data Exchange (ETDEWEB)

Anderson, T.V.; Johnson, A.G.; Bennett, S.L.; Ringle, J.C.

1979-08-31

The use of the Oregon State University TRIGA Reactor during the year ending June 30, 1979, is summarized. Environmental and radiation protection data related to reactor operation and effluents are included.

Oregon State University TRIGA Reactor annual report

International Nuclear Information System (INIS)

Anderson, T.V.; Johnson, A.G.; Bennett, S.L.; Ringle, J.C.

1979-01-01

The use of the Oregon State University TRIGA Reactor during the year ending June 30, 1979, is summarized. Environmental and radiation protection data related to reactor operation and effluents are included

Aircraft observations of aerosols O{sub 3} and NO{sub y} in a nighttime urban plume

Energy Technology Data Exchange (ETDEWEB)

Berkowitz, C.M.; Zaveri, R.A.; Xindi Bian; Shiyuan Zhong; Disselkamp, R.S.; Laulainen, N.S.; Chapman, E.G. [Pacific Northwest National Lab., Richland, WA (United States)

2001-05-01

Nighttime measurements of aerosol surface area, O{sub 3}, NO{sub y} and moisture were made downwind of Portland, Oregon, as part of a study to characterize the chemistry in a nocturnal urban plume. Air parcels sampled within the urban plume soon after sunset had positive correlations between O{sub 3}, relative humidity, NO{sub y} and aerosol number density. However, the air parcels sampled within the urban plume just before dawn had O{sub 3} mixing ratios that were highly anti-correlated with aerosol number density, NO{sub y} and relative humidity. Back-trajectories from a mesoscale model show that both the post-sunset and pre-dawn parcels came from a common maritime source to the northwest of Portland. The pre-dawn parcels with strong anti-correlations passed directly over Portland in contrast to the other parcels that were found to pass west of Portland. Several gas-phase mechanisms and a heterogeneous mechanism involving the loss of O{sub 3} to the aerosol surface, are examined to explain the observed depletion in O{sub 3} within the pre-dawn parcels that had passed over Portland. (Author)

Clinical and computed tomographic evaluation of portland cement pulpotomy in primary molar: A case report

Directory of Open Access Journals (Sweden)

Kamrun Nahar

2016-08-01

Full Text Available The present case describes the clinical & radiographic outcome of a Portland Cement pulpotomy. The 5 years old girl presenting extensive carious exposure in her mandibular left 2nd deciduous molar and was suffering pain in her left lower jaw only on exposure to cold for last 2 days. She was ultimately diagnosed clinic-radio-graphically as a case of irreversible pulpitis. Coronal pulpotomy procedure was carried out in the responsible tooth and Portland cement (PC was applied as a medicament after pulpotomy. At the 3 & 6-months follow-up appointments, treated tooth was asymptomatic clinically and radiographic examinations revealed no sign of periradicular pathosis in the pulpotomized teeth. Additionally, the formation of a dentin bridge immediately below the PC in the treated tooth was confirmed by RVG and CBCT.

Oregon's forest products industry: 1994.

Science.gov (United States)

Franklin R. Ward

1997-01-01

This report presents the findings of a survey of primary forest products industries in Oregon for 1994. The survey included the following sectors: lumber; veneer; pulp and board; shake and shingle; export; and post, pole, and piling. Tables, presented by sector and for the industry as a whole, include characteristics of the industry, nature and flow of logs consumed,...

Improving commercial motor vehicle safety in Oregon.

Science.gov (United States)

2010-08-01

This study addressed the primary functions of the Oregon Department of Transportations (ODOTs) Motor Carrier Safety Assistance Program (MCSAP), which is administered by the Motor Carrier Transportation Division (MCTD). The study first documente...

DCS Hydrology Submission for Lincoln County, Oregon

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — The hydrology dataset for Lincoln County, Oregon includes proposed 10-, 50-, 100-, and 500-year discharges for Salmon River, Schooner Creek, Drift Creek, Siletz...

77 FR 64444 - VOR Federal Airway V-595; Oregon

Science.gov (United States)

2012-10-22

... Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). SUMMARY: This action... this action to redescribe the route due to the scheduled decommissioning of the Portland, OR, VOR/DME... suggestions presented are particularly helpful in developing reasoned regulatory decisions on the proposal...

Increasing Diversity in the Earth Sciences (IDES) - An Oregon Effort

Science.gov (United States)

de Silva, S. L.; Duncan, R. A.; Wright, D. J.; de Silva, L.; Guerrero, E. F.

2011-12-01

The IDES (Increasing Diversity in Earth Sciences) Program is the first partnership of its kind in the state of Oregon targeted at broadening participation in the Earth Science enterprise. Funded by the National Science Foundation Opportunities to Enhance Diversity in the Geosciences program (NSF-OEDG), this partnership involves community colleges, a research university with major strengths in Earth Science research and education and an institutionalized commitment to enhancing diversity, state and federal agencies, centers of informal education, and the Oregon Space Grant Consortium, IDES has two integrated goals: 1) to increase the number of students from under-represented groups who pursue careers in Earth Science research and education, and 2) to strengthen the understanding of Earth Sciences and their relevance to society among broad and diverse segments of the population. Built around the best practices of tiered mentoring, interactive student cohort, research and education internships, and financial support, this 4-year program recruits 10 to 12 students (mainly rising juniors) each year from science majors at Oregon State University and five Oregon community colleges. The program is reaching its goals by: a) training participants in the application of geospatial to Earth Science problems of personal relevance b) immersing participants in a two-year mentored research project that involves summer internships with academic units, state and federal agencies, and centers for informal education in Oregon. c) exposing, educating, and involving participants in the breadth of Earth Science careers through contact with Earth Science professionals through mentors, a professional internship, and a learning community that includes a speaker series. d) instilling an understanding of context and relevance of the Earth Science Enterprise to the participants, their families, their communities, and the general public. We report on the first two years of this program during

Puzzolanic cements of greater resistance at the attack of selenitic waters than the high sulfate resistance portland cements, and viceverse

Directory of Open Access Journals (Sweden)

Talero, Rafael

1987-09-01

Full Text Available This work confirms the certainty of the predictions of useful service given by Kaluosek and al. for the sulphate resistant portland cements (type V, USA, subject to severe selenitic attack. Two sulphate resistant portland cements, were tested by means of the Le Chatelier Anstett method. The tarts were destroyed at ages of three years, having detected in them the presence of thaumasite by XRD. Even so, the impossibility and possibility thaumasite formation was confirmed in pozzolanic cements tarts, which either had or did not have adequate amount of pozzolana (diatomite for such purpose.

Este trabajo confirman las predicciones de vida útil dadas por Kalousek y colaboradores, para los cementos portland de elevada resistencia al ataque de los iones sulfato (tipo V, USA, sometidos a un severo ataque selenitoso. Se ensayaron dos cementos portland de elevada resistencia al ataque del yeso, mediante el ensayo de Le Chatelier-Anstett. Sus tortas correspondientes se destruyeron a la edad de tres años, habiéndose detectado en las mismas la presencia de thaumasita por DRX. Asimismo se confirmó la imposibilidad y posibilidad de formación de thaumasita en tortas de cementos puzolánicos, los cuales tenían, o no, respectivamente, una adecuada cantidad de puzolana (diatomita para tales fines.

Shifting the paradigm in Oregon from teen pregnancy prevention to youth sexual health.

Science.gov (United States)

Nystrom, Robert J; Duke, Jessica E A; Victor, Brad

2013-01-01

Oregon's work on teen pregnancy prevention during the previous 20 years has shifted from a risk-focused paradigm to a youth development model that places young people at the center of their sexual health and well-being. During 2005, the Oregon Governor's Office requested that an ad hoc committee of state agency and private partners develop recommendations for the next phase of teen pregnancy prevention. As a result of that collaborative effort, engagement of young people, and community input, the Oregon Youth Sexual Health Plan was released in 2009. The plan focuses on development of young people and embraces sexuality as a natural part of adolescent development. The plan's five goals and eight objectives guide the work of state agencies and partners addressing youth sexual health. Oregon's development of a statewide plan can serve as a framework for other states and entities to address all aspects of youth sexual health.

75 FR 17950 - Notice of Intent To Prepare Amendments to the Southeastern Oregon Resource Management Plan (RMP...

Science.gov (United States)

2010-04-08

... Cicuit ruled on the Southeastern Oregon RMP in Oregon Natural Desert Association v. Bureau of Land... Lakeview RMP in Oregon Natural Desert Association v. Gammon, No. 07- 35728 (9th Cir.), pending resolution... observed; A systematic interdisciplinary approach to integrate, physical, biological, economic, and other...

Urban trees and the risk of poor birth outcomes

Science.gov (United States)

Geoffrey H. Donovan; Yvonne L. Michael; David T. Butry; Amy D. Sullivan; John M. Chase

2011-01-01

This paper investigated whether greater tree-canopy cover is associated with reduced risk of poor birth outcomes in Portland, Oregon. Residential addresses were geocoded and linked to classified-aerial imagery to calculate tree-canopy cover in 50, 100, and 200 m buffers around each home in our sample (n=5696). Detailed data on maternal characteristics and additional...

1st Fire Behavior and Fuels Conference: Fuels Management-How to Measure Success

Science.gov (United States)

Patricia L. Andrews

2006-01-01

The 1st Fire Behavior and Fuels Conference: Fuels Management -- How to Measure Success was held in Portland, Oregon, March 28-30, 2006. The International Association of Wildland Fire (IAWF) initiated a conference on this timely topic primarily in response to the needs of the U.S. National Interagency Fuels Coordinating Group (http://www.nifc.gov/).

Two Sides of the Same Coin: Faculty Doing Research

Science.gov (United States)

Berg, Steven L.

2006-01-01

Dr. Richard Sagor is the Educational Leadership Program Director and a professor in the Department of Education at Lewis & Clark College in Portland, Oregon. Dr. Howard Tinberg is a professor of English at Bristol Community College in Fall River, Massachusetts, where he is also director of the Writing Lab. He is the editor of the journal…

Understanding concepts of place in recreation research and management.

Science.gov (United States)

Linda. E. Kruger; Troy E. Hall; Maria C. Stiefel

2008-01-01

Over a 3-day weekend in the spring of 2004 a group of scientists interested in extending understanding of place as applied in recreation research and management convened a working session in Portland, Oregon. The purpose of the gathering was to clarify their understanding of place-related concepts, approaches to the study of people-place relations, and the application...

Physical chemistry of portland-cement hydrate, radioactive-waste hosts: Final report, January 16, 1987--December 31, 1987

International Nuclear Information System (INIS)

Grutzeck, M.W.

1989-01-01

This is a final report summarizing the results of a study of the physical and crystal chemistry of potential hydroxylated radioactive waste hosts compatible with portland cement. Research has focussed on the identification and evaluation of hydrated host phases for four ions: cesium, strontium, iodine and boron. These ions were chosen because they are among the most long lived of the radioactive waste ions as well as the most difficult to immobilize with cement-based materials. Results show that such phases do indeed exist, and that they are excellent host phases for the above ions

Floodplain Mapping Submission for Oregon County, MO

Data.gov (United States)

Federal Emergency Management Agency, Department of Homeland Security — The Floodplain Mapping study deliverables depict and quantify the flood risks for Oregon County, MO. The City of Thayer and the Missouri State Emergency Management...

National Hydroelectric Power Resources Study: Regional Assessment: Volume XXII: Western Systems Coordinating Council, (WSCC). Volume 22

Science.gov (United States)

1981-09-01

largest combustion- turbine plants, both over 200 MW, are the Harborton facility in Portland, Oregon, owned by Portland General Electric, and Agua ...SUU 110 Sl/U CJt SUU III Ii/U :r 93 SUU 94 Si/U W 95 IlIU U Si/U 97 SlIU 98 SitU 99 SlIU 100 Si/U 101 SlIU 102 Si/U 103 Fl RlIV 104 01 R2...YNNNYNN * * S 2 * MARICOPA AGUA FRIA elV. 112 lb.l * UP * 103800 * 1500 * 32b5 * 57.781 * * * AS * MCM~CD PI * tij~9 * 60.0* 170,8 * 1500 * l2bS

Newport, Oregon 1/3 arc-second DEM

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The 1/3-second Newport, Oregon Elevation Grid provides bathymetric data in ASCII raster format of 1/3-second resolution in geographic coordinates. This grid is...

Seaside, Oregon 1/3 arc-second DEM

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The 1/3-second Seaside Oregon Elevation Grid provides bathymetric data in ASCII raster format of 1/3-second resolution in geographic coordinates. This grid is...

2015 Oregon Department Forestry Lidar: Northwest OR

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — GeoTerra, Inc. was selected by Oregon Department of Forestry to provide Lidar remote sensing data including LAZ files of the classified Lidar points and surface...

Expect the unexpected: place-based protections can lead to unforeseen benefits

Science.gov (United States)

Rebecca L. Flitcroft; Daniel L. Bottom; Karen L. Haberman; Ken F. Bierly; Kim K. Jones; Charles A. Simenstad; Ayesha Gray; Kami S. Ellingson; Erin Baumgartner; Trevan J. Cornwell; Lance A. Campbell

2016-01-01

1. Protection of places important for aesthetic, ecological, and cultural values has been a goal of conservationists for over 150 years. Cornerstones of place-based conservation include legal designations, international agreements, and purchase by public or non-profit organizations.2. In the Salmon River catchment, Oregon, protections were initially...

The Arabic Version of the Mayo-Portland Adaptability Inventory 4: A Validation Study

Science.gov (United States)

Hamed, Razan; Tariah, Hashem Abu; Malkawi, Somaya; Holm, Margo B.

2012-01-01

The Mayo-Portland Adaptability Inventory 4 (MPAI-4) is a valid and reliable assessment tool to detect clinical impairments in patients with acquired brain injury. The tool is widely used by rehabilitation therapists worldwide, given its good psychometric properties and its availability in several languages. The purpose of this study was to…

Relation between Portland cement carbonation, range of clinker burning and some expansive phenomena in the autoclave test

Directory of Open Access Journals (Sweden)

Ruiz de Cauna, A.

1975-12-01

Full Text Available Not availableEn este trabajo se estudia el doble pico que aparece en la región de altas temperaturas de las curvas derivatométricas, realizadas en atmósfera de vapor de agua, de los cementos portland anhidros e hidratados y en general el efecto de la carbonatación sobre los silicatos y aluminatos presentes en los cementos portland, especialmente sobre el perfil de las curvas derivatométricas de los cementos portland anhidros e hidratados. Se recogen y examinan los cambios experimentados en el doble pico al someter los cementos a la acción de diversos tratamientos y de agentes modificantes, tales como el tiempo, el CO2, la hidratación normal, las hidrataciones bajo agua a ebullición, en autoclave y en suspensión acuosa con agitación, la adición de puzolana y de fuertes proporciones de S04Ca. Se estudia y compara, asimismo, el comportamiento al análisis térmico bajo vapor de agua y al ensayo de autoclave de algunos clínkeres y cementos que presentan el doble pico en forma acusada y poco apreciable, respectivamente. De los resultados obtenidos se deducen conclusiones que explican los comportamientos experimentales observados. Las principales conclusiones se refieren a la interpretación de los picos que aparecen en las curvas derivatométricas o de velocidad de pérdida de peso de los cementos portland anhidros e hidratados, y a algunos aspectos de su carbonatación, a la probable existencia de un compuesto intermedio, consecuencia de la incompleta formación del silicato tricálcico y a la explicación de determinadas grandes expansiones producidas en el ensayo de autoclave.

Effectiveness of shrinkage-reducing admixtures on Portland pozzolan cement concrete

Directory of Open Access Journals (Sweden)

Videla, C.

2005-06-01

Full Text Available Drying shrinkage causes tensile stress in restrained concrete members. Since all structural elements are subject to some degree of restraint, drying shrinkage is regarded to be one of the main causes of concrete cracking. The purpose of the present study was to evaluate the effectiveness of SRA in reducing drying shrinkage strain in Portland pozzolan cement concrete. The major variables examined included slump, admixture type and dose, and specimen size. The measured results indicate that any of the admixtures used in the study significantly reduced shrinkage. Concrete manufactured with shrinkage reducing admixtures shrank an average of 43% less than concrete without admixtures. As a rule, the higher the dose of admixture, the higher was its shrinkage reduction performance. The experimental results were compared to the shrinkage strain estimated with the ACI 209, CEB MC 90, B3, GL 2000, Sakata 1993 and Sakata 2001 models. Although none of these models was observed to accurately describe the behaviour of Portland pozzolan cement concrete with shrinkage reducing admixtures, the Sakata 2001 model, with a weighted coefficient of variation of under 30%, may be regarded to be roughly adequate.

La retracción por secado es un fenómeno intrínseco del hormigón que produce tensiones de tracción en elementos restringidos de hormigón. Puesto que todos los elementos presentan algún grado de retracción, se considera a la retracción por secado como una de las principales causas de agrietamiento en proyectos de construcción en hormigón. Por lo tanto, el objetivo de esta investigación fue evaluar la efectividad de los aditivos reductores de retracción (SRA en hormigones fabricados con cemento Portland puzolánico. Las variables principales estudiadas incluyen el asentamiento de cono de Abrams, marca y dosis de aditivo reductor de retracción, y tamaño de espécimen de hormigón. Los resultados obtenidos permiten concluir que el uso de

Resident wellness: institutional trends over 10 years since 2003

Directory of Open Access Journals (Sweden)

Choi D

2017-07-01

Full Text Available Dongseok Choi,1,2 Andrea Cedfeldt,3,4 Christine Flores,5 Kimberly Irish,3 Patrick Brunett,3,6 Donald Girard3,4 1OHSU-PSU School of Public Health, Oregon Health & Science University, Portland, OR, USA; 2School of Dentistry, Kyung Hee University, Seoul, Korea; 3Division of Graduate Medical Education, 4Department of Medicine, 5Division of Continuing Professional Development, 6Department of Emergency Medicine, Oregon Health & Science University, Portland, OR, USA Background: The surveys in this study were carried out at the Graduate Medical Education Division at Oregon Health & Science University (OHSU. OHSU implemented two significant wellness initiatives: a wellness program in 2004, and a policy allowing 4 half-days off each academic year to pursue personal or family health care needs in 2010. This study provides a secondary data analysis of five cross-sectional surveys of career satisfaction of resident and fellow trainees. Methods: All trainees were surveyed five times over a 10-year period using anonymous, cross-sectional web-based survey instruments. Surveys included questions about career satisfaction, perceived stress, sleep hours, burnout, and related factors.Results: This represents 10 years of accumulated responses from over 2,200 residents with results showing continual improvement in their career satisfaction. Response rates ranged from 56% to 72%. During the study period, there was a significant positive change in overall resident career satisfaction, with little change in factors traditionally considered to be predictive of overall career satisfaction such as sleep hours or perceived stress level. In addition, our data support that availability of time for personal tasks could positively impact the overall training experience.Conclusion: We postulate that the improvements in satisfaction relate to two major institutional innovations designed to promote resident wellness. Keywords: satisfaction, burnout, graduate medical education

Oregon School Bond Manual. Fifth Edition.

Science.gov (United States)

Oregon State Dept. of Education, Salem.

To help school districts comply with Oregon's school bond laws, this manual provides guidelines for school district attorneys and personnel in the issuance and sale of school bonds. The document describes the proper time sequence of the bonding procedure, including elections, school board authorizations, necessary certificates, bond registration…

Influence of bismuth oxide concentration on the pH level and biocompatibility of white Portland cement.

Science.gov (United States)

Marciano, Marina Angélica; Garcia, Roberto Brandão; Cavenago, Bruno Cavalini; Minotti, Paloma Gagliardi; Midena, Raquel Zanin; Guimarães, Bruno Martini; Ordinola-Zapata, Ronald; Duarte, Marco Antonio Hungaro

2014-01-01

To investigate if there is a relation between the increase of bismuth oxide and the decrease of pH levels and an intensification of toxicity in the Portland cement. White Portland cement (WPC) was mixed with 0, 15, 20, 30 and 50% bismuth oxide, in weight. For the pH level test, polyethylene tubes were filled with the cements and immersed in Milli-Q water for 15, 30 and 60 days. After each period, the increase of the pH level was assessed. For the biocompatibility, two polyethylene tubes filled with the cements were implanted in ninety albino rats (n=6). The analysis of the intensity of the inflammatory infiltrate was performed after 15, 30 and 60 days. The statistical analysis was performed using the Kruskal-Wallis, Dunn and Friedman tests for the pH level and the Kruskal-Wallis and Dunn tests for the biological analysis (p0.05). For the inflammatory infiltrates, no significant statistical differences were found among the groups in each period (p>0.05). The 15% WPC showed a significant decrease of the inflammatory infiltrate from 15 to 30 and 60 days (pPortland cement did not affect the pH level and the biological response. The concentration of 15% of bismuth oxide resulted in significant reduction in inflammatory response in comparison with the other concentrations evaluated.

Team-based global organizations

DEFF Research Database (Denmark)

Zander, Lena; Butler, Christina; Mockaitis, Audra

2015-01-01

diversity in enhancing team creativity and performance, and 2) the sharing of knowledge in team-based organizations, while the other two themes address global team leadership: 3) the unprecedented significance of social capital for the success of global team leader roles; and 4) the link between shared......This chapter draws on a panel discussion of the future of global organizing as a team-based organization at EIBA 2014 in Uppsala, Sweden. We began by discussing contemporary developments of hybrid forms of hierarchy and teams-based organizing, but we venture to propose that as organizations become...... characterized by decreased importance of hierarchal structures, more fluidity across borders, even a possible dissolution of firm boundaries, we move towards team-based organizing as an alternative to more traditional forms of hierarchical-based organizing in global firms. To provide input for a discussion...

The Influence of Diatomite on the Strength and Microstructure of Portland Cement

Directory of Open Access Journals (Sweden)

Liu Jun

2016-01-01

Full Text Available To study the influence of the types and mixing amount of diatomite on the Portland cement, we prepared the cement specimen doped with the calcined first-grade, first-grade and second-grade diatomite ,tested the 3d, 7d, 14d compressive strength, and studied and discussed phase, structure and morphology of diatomite in the binary system by the method of XRD, SEM . Experimental results show that with the addition of diatomite, the strength of cement paste increase; the optimal contents of calcined first-grade ,first-grade and second-grade diatomite in Portland cement are 5%,Compared to the blank group, the strength of specimen can be increased by 54.6%, 15.4% and 10.2%, respectively; At the same time ,the 7d microscopic hydration of different diatomite particles were analyzed through the experiment , and the shell of calcined diatomite particles were better hydrated than that of first-grade and second-grade diatomite particles. The results indicate that the diatomite can improve the strength of cement paste, the hydration of different diatomite particles can influence the growth of cement paste strength.

Characteristics of novel root-end filling material using epoxy resin and Portland cement.

Science.gov (United States)

Lee, Sang-Jin; Chung, Jin; Na, Hee-Sam; Park, Eun-Joo; Jeon, Hyo-Jin; Kim, Hyeon-Cheol

2013-04-01

The aim of this study was to evaluate the physical properties and cytotoxicity of a novel root-end filling material (EPC) which is made from epoxy resin and Portland cement as a mineral trioxide aggregate (MTA) substitute. EPC, developed as a root-end filling material, was compared with MTA and a mixture of AH Plus sealer and MTA (AMTA) with regard to the setting time, radio-opacity, and microleakage. Setting times were evaluated using Vicat apparatus. Digital radiographs were taken to evaluate the aluminium equivalent radio-opacity using an aluminium step wedge. Extracted single-rooted teeth were used for leakage test using methylene blue dye. After canal shaping and obturation, the apical 3-mm root was resected, and a root-end cavity with a depth of 3 mm was prepared. The root-end cavities were filled with MTA, AMTA, and EPC for 15 specimens in each of three groups. After setting in humid conditions for 24 h, the specimens were tested for apical leakage. For evaluation of the biocompatibility of EPC, cell (human gingival fibroblast) viability was compared for MTA and Portland cement by MTT assay, and cell morphological changes were compared for MTA and AH Plus by fluorescence microscopy using DAPI and F-actin staining. The setting time, radio-opacity, and microleakage were compared using one-way ANOVA and Scheffe's post hoc comparison, and the cytotoxicity was compared using the nonparametric Kruskal-Wallis rank sum test. Statistical significance was set at 95%. EPC had a shorter setting time and less microleakage compared with MTA (p Portland cement, was found to be a useful material for root-end filling, with favourable radio-opacity, short setting time, low microleakage, and clinically acceptable low cytotoxicity. The novel root-end filling material would be a potentially useful material for a surgical endodontic procedure with favourable properties.

Effect of calcium/silicon ratio on retention of uranium (VI) in portland cement materials

International Nuclear Information System (INIS)

Tan Hongbin; Li Yuxiang

2005-01-01

Calcium silicate hydrate (CSH) materials of varied calcium to silicon (Ca/Si) ratios were prepared by hydrothermal synthesis at 80 degree C, with calcium oxide and micro-silicon employed. These products were determined to be of gel phase by XRD. Leaching tests with 1% hydrochloric acid indicated that more Uranium (VI) was detained by CSH with lower Ca/Si ratios. Alkali-activated slag cement (with a lower Ca/Si ratio) was found to have a stronger retention capacity than Portland cement (with a higher Ca/Si ratio), at 25 degree C in 102-days leaching tests with simulated solidified forms containing Uranium (VI). The accumulative leaching fraction of Uranium (VI) for Alkali-activated slag cement solidified forms is 17.6% lower than that for Portland cement. The corresponding difference of diffusion coefficients is 40.6%. This could be correlated with the difference of Ca/Si ratios between cements of two kinds. (authors)

Measurement of the leaching rate of radionuclide 134Cs from the solidified radioactive sources in Portland cement mixed with microsilica and barite matrixes

International Nuclear Information System (INIS)

Shaaban, Ismail; Assi, Nasim

2011-01-01

Portland cement was mixed with radionuclide 134 Cs to produce low-level radioactive sources. These sources were surrounded with cement mixed with different materials like microsilica and barite. The leaching rate of 134 Cs from the solidified radioactive source in Portland cement alone was found to be 4.481 x 10 -4 g/cm 2 per day. Mixing this Portland cement with microsilica and with barite reduced significantly the leaching rate to 1.091 x 10 -4 g/cm 2 per day and 3.153 x 10 -4 g/cm 2 per day for 1 wt.% mixing, and to 1.401 x 10 -5 g/cm 2 per day and 1.703 x 10 -4 g/cm 2 per day for 3 wt.% mixing, respectively. It was also found that the application of a latex paint reduced these leaching rates by about 6.5%, 20.3% and 13.3% for Portland cement, cement mixed with microsilica and with barite, respectively. The leaching data were also analyzed using the polynomial method. The obtained results showed that cement mixed with microsilica and with barite can be effectively used for radioactive sources solidification.

The Holy Dose: Spiritual adventures with Southern Oregon's psychedelic crusaders

OpenAIRE

Weber, Alex L

2011-01-01

Ashland, Oregon is a smart little community nestled in the foothills of the Siskiyou Mountains about 20 minutes north of the California border. Home to Southern Oregon University and host to the yearly Shakespeare Festival, Ashland is one of those places both progressive and picturesque that often occupies a top spot on waiting-room magazines' “Best Small Towns” or “Best Places to Retire” lists. It's got a walkable business district with cozy fine-dining bistros, new-age book shops and old-sc...

Thiazole-based organic semiconductors for organic electronics.

Science.gov (United States)

Lin, Yuze; Fan, Haijun; Li, Yongfang; Zhan, Xiaowei

2012-06-19

Over the past two decades, organic semiconductors have been the subject of intensive academic and commercial interests. Thiazole is a common electron-accepting heterocycle due to electron-withdrawing nitrogen of imine (C=N), several moieties based on thiazole have been widely introduced into organic semiconductors, and yielded high performance in organic electronic devices. This article reviews recent developments in the area of thiazole-based organic semiconductors, particularly thiazole, bithiazole, thiazolothiazole and benzobisthiazole-based small molecules and polymers, for applications in organic field-effect transistors, solar cells and light-emitting diodes. The remaining problems and challenges, and the key research direction in near future are discussed. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.