Preparation and antibacterial activities of chitosan-gallic acid/polyvinyl alcohol blend film by LED-UV irradiation.

Science.gov (United States)

Yoon, Soon-Do; Kim, Young-Mog; Kim, Boo Il; Je, Jae-Young

2017-11-01

Active blend films from chitosan-gallic acid (CGA) and polyvinyl alcohol (PVA) were prepared via a simple mixing and casting method through the addition of citric acid as a plasticizer. The CGA/PVA blend films were characterized using Fourier transform infrared spectroscopy (FT-IR). The mechanical properties including tensile strength (TS) and elongation at break (%E), degree of solubility (S) and swelling behavior (DS), water vapor adsorption, and antimicrobial activities of the CGA/PVA blend films with and without LED (light emitting diode)-UV irradiation were also investigated. The CGA/PVA blend films exposed to UV irradiation exerted a higher TS (43.5MPa) and lower %E (50.40), S (0.38) and DS (2.73) compared to the CGA/PVA blend films (TS=41.7MPa, %E=55.40, S=0.42, and DS=3.16) not exposed LED-UV irradiation, indicating that the cross-linkage between CGA and PVA had been strengthened by LED-UV irradiation. However, the water vapor adsorption in the CGA/PVA blend films increased due to the changes of surface roughness and pore volume after LED-UV irradiation, and all values increased by increasing the CGA concentrations in the CGA/PVA blend films. The antimicrobial activities of the CGA/PVA blend films showed that the efficient concentration of CGA in the CGA/PVA blend films was over 1.0%. Taken together, the CGA/PVA blend films have potential for use as food packing materials. Copyright © 2017 Elsevier B.V. All rights reserved.

Preparation of Polyvinyl Alcohol/Xylan Blending Films with 1,2,3,4-Butane Tetracarboxylic Acid as a New Plasticizer

Directory of Open Access Journals (Sweden)

Cun-dian Gao

2014-01-01

Full Text Available Miscible, biodegradable polyvinyl alcohol (PVA/xylan blending films were firstly prepared in the range of the PVA/xylan weight ratio from 1 : 2 to 3 : 1 by casting method using 1,2,3,4-butane tetracarboxylic acid (BTCA as a new plasticizer. The properties of blending films as functions of PVA/xylan weight ratio and BTCA amount were discussed. XRD and FT-IR were applied to characterize the blending films. Experimental results indicated that tensile strength (TS and elongation at break (EAB of blending films decreased along with the decrease of the PVA/xylan weight ratio. Both of TS and EAB firstly increased and then decreased as the amount of BTCA was increased. More importantly, blending films were biodegraded almost by 41% with an addition of 10% BTCA in blending films within 30 days in soil. For all hydroxyl functionalized polymers (xylan and PVA, their molecular interactions and miscibility with BTCA endowed blending films with the biocompatibility and biodegradability. Therefore, these blending films are environmentally friendly materials which could be applied as biodegradable plastics for food packaging and agricultural applications.

Studies on the Electrical Properties of Graphene Oxide-Reinforced Poly (4-Styrene Sulfonic Acid) and Polyvinyl Alcohol Blend Composites

Science.gov (United States)

Deshmukh, Kalim; Sankaran, Sowmya; Basheer Ahamed, M.; Khadheer Pasha, S. K.; Sadasivuni, Kishor Kumar; Ponnamma, Deepalekshmi; Al-Ali Almaadeed, Mariam; Chidambaram, K.

In the present study, graphene oxide (GO)-reinforced poly (4-styrenesulfonic acid) (PSSA)/polyvinyl alcohol (PVA) blend composite films were prepared using colloidal blending technique at various concentrations of GO (0-3wt.%). The morphological investigations of the prepared composites were carried out using polarized optical microscopy and scanning electron microscopy. The electrical properties of composites were evaluated using an impedance analyzer in the frequency range 50Hz to 20MHz and temperature in the range 40-150∘C. Morphological studies infer that GO was homogeneously dispersed in the PSSA/PVA blend matrix. Investigations of electrical property indicate that the incorporation of GO into PSSA/PVA blend matrix resulted in the enhancement of the impedance (Z) and the quality factor (Q-factor) values. A maximum impedance of about 4.32×106Ω was observed at 50Hz and 90∘C for PSSA/PVA/GO composites with 3wt.% GO loading. The Q-factor also increased from 8.37 for PSSA/PVA blend to 59.8 for PSSA/PVA/GO composites with 3wt.% GO loading. These results indicate that PSSA/PVA/GO composites can be used for high-Q capacitor applications.

21 CFR 177.1670 - Polyvinyl alcohol film.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Polyvinyl alcohol film. 177.1670 Section 177.1670... Components of Single and Repeated Use Food Contact Surfaces § 177.1670 Polyvinyl alcohol film. Polyvinyl alcohol film may be safely used in contact with food of the types identified in § 176.170(c) of this...

[Preparation and physicochemical property of carboxymethyl-chitosan/hyaluronic acid poly(vinyl alcohol) blend membrane].

Science.gov (United States)

Liu, Wen; Li, Shuning; Chang, Jing; Han, Baoqin; Liu, Wanshun

2009-08-01

To prepare carboxymethyl-chitosan/hyaluronic acid/poly(vinyl alcohol) (CHP) blend membrane, evaluate its physicochemical properties and intraocular biocompatibility and to investigate its feasibility to be applied to glaucoma filtering surgery. CHP blend membrane was prepared using solution casting method after blending carboxymethyl-chitosan, HA and poly(vinyl alcohol) in a proportion of 5 : 4 : 1 (M/M). Its water absorption rate, swelling rate, permeability, and mechanical properties were detected. Subconjunctival fibroblasts separated from subconjunctival tissue of New Zealand white rabbits were cultured, and the cells at passage 4 were cultured on cell culture plate with or without the CHP blend membrane, serving as the experimental group and the control group, respectively. Effect of the CHP blend membrane on the subconjunctival fibroblasts was tested by MTT method 24, 48, and 72 hours after culture. Six New Zealand white rabbits were randomly divided into two groups (n = 3 rabbits per group), and the CHP blend membrane and SK gel were implanted into the rabbits' subconjunctival space and anterior chamber in the experimental group and the control group, respectively. Slit lamp observation and binocular reaction record were conducted 1, 3, 5, 9, 11, 20, 30, 45, and 60 days after operation. Corneal tissue harvested from the experimental group was observed using scanning electron microscope 15 days after operation to study ophthalmic biocompatibility and biodegradability. The water absorption rate and the swelling rate of the CHP blend membrane was 83.8% +/- 1.3% and 3.59 +/- 0.50, respectively. The tensile strength of the dry and the wet CHP blend membrane was (20.59 +/- 1.73) and (0.51 +/- 0.13) MPa, respectively. The breaking elongation rate of the dry and the wet CHP blend membrane was 10.69% +/- 1.16% and 53.15% +/- 2.46%, respectively. The CHP blend membrane had good permeability to NaCl and L-tyrosine. Absorbance (A) value of the experimental group 24, 48

Resistance of polyvinyl alcohol blends stabilized by sodium and ammonium salts of lignite humic acids against γ-irradiation

International Nuclear Information System (INIS)

Barbora Bakajova; Jiri Kucerik; Michal Ilcin; Oga Hola

2011-01-01

The dried blends containing sodium and ammonium salts of lignite humic acids (humates, 0.5-10% w/w) in polyvinyl alcohol (PVA) were exposed to high dosage of γ-irradiation in the range of doses 127-806 kGy. Resulted products were then tested for their stability using thermogravimetrical analysis. As a reference the non-treated blends were used since the pure PVA exposed to γ-irradiation very quickly lost its stability and resulting consistence did not allow the stability tests. Stabilities showed a strong concentration and counterion dependency. While sodium counterion caused mostly destabilization with increasing dose, the ammonium counterion acted in an opposite way. The tests carried out in a moisturizing container revealed the changes in water absorbing capacity of irradiated samples and allowed partial explanation of humate stabilizing effect. Generally, at lower concentration of a humate the increase was observed with an increase in the γ-irradiation dose and vice versa. The results confirmed the antioxidant and stabilizing effect of humic acids added to some synthetic polymers and their applicability in materials exposed to γ-irradiation. (author)

Spectroscopic, thermal, and electrical properties of MgO/ polyvinyl pyrrolidone/ polyvinyl alcohol nanocomposites

Science.gov (United States)

Mohammed, Gh.; El Sayed, Adel M.; Morsi, W. M.

2018-04-01

In this study, we aimed to control the optical and electrical properties of polyvinyl alcohol (PVA) in order to broaden its industrial and technological applications, which we achieved by blending PVA with polyvinyl pyrrolidone (PVP) and adding sol-gel prepared MgO nanopowder. The blended film and nanocomposite films were prepared using the solution casting technique. X-ray diffraction analyses showed that the crystallite size was ∼18.4 nm for MgO and the highest degree of crystallinity (XC) in the films was about 24.34% at 1.0 wt% MgO. High resolution transmission electron microscopy determined the nanoribbon morphology of MgO. Scanning electron microscopy (SEM) indicated the uniform distribution of the MgO nanoribbons on the surfaces of the PVA/PVP films. SEM and Fourier transform infrared spectroscopy also confirmed the interaction between the blend and MgO fillers. The effects of the additives on the glass transition (Tg) and melting (Tm) temperatures were evaluated by differential thermal analysis and differential scanning calorimetry. The appearance of one melting point confirmed the miscibility of the two polymers. According to ultraviolet-visible-near infrared spectroscopy measurements, the optical properties and optical constants of PVA could be adjusted by the addition of PVP and MgO, where the optical band gap (Eg) determined for PVA increased with the PVP content, whereas it decreased to 4.8 eV as the MgO content increased. The DC conductivity (σdc) of the films increased whereas the activation energy (Ea) decreased after the addition of MgO, possibly because the nanoribbon shape fixed the preferred conducting pathways. In addition, MgO could break the H-bond in sbnd OH groups of the blends to allow the free movement of the molecular chains.

Polyvinyl alcohol/starch composite nanofibers by bubble electrospinning

Directory of Open Access Journals (Sweden)

Liu Zhi

2014-01-01

Full Text Available Bubble electrospinning exhibits profound prospect of industrialization of macro/ nano materials. Starch is the most abundant and inexpensive biopolymer. With the drawbacks of poor strength, water resistibility, thermal stability and processability of pure starch, some biodegradable synthetic polymers such as poly (lactic acid, polyvinyl alcohol were composited to electrospinning. To the best of our knowledge, composite nanofibers of polyvinyl alcohol/starch from bubble electrospinning have never been investigated. In the present study, nanofibers of polyvinyl alcohol/starch were prepared from bubble electrospinning. The processability and the morphology were affected by the weight ratio of polyvinyl alcohol and starchy. The rheological studies were in agreement with the spinnability of the electrospinning solutions.

Crosslinked poly(vinyl alcohol)/sulfonated poly(ether ether ketone) blend membranes for fuel cell applications - Surface energy characteristics and proton conductivity

Energy Technology Data Exchange (ETDEWEB)

Kanakasabai, P.; Vijay, P.; Deshpande, Abhijit P.; Varughese, Susy [Department of Chemical Engineering, Indian Institute of Technology Madras, Chennai 600 036 (India)

2011-02-01

Ionic polymers, their blends and composites are considered potential candidates for application as electrolytes in fuel cells. While developing new materials for membranes, it is important to understand the interactions of these electrolytic materials with electrodes/catalysts and with reactants/products. Some of these interactions can be understood by estimating the surface energy and wettability of the membrane materials. In this work, polyvinyl alcohol with varying degrees of sulfonation and its blend with sulfonated poly(ether ether ketone) are prepared and studied for their wettability characteristics using goniometry. The surface energy and its components are estimated using different approaches and compared. Properties such as the ion-exchange capacity, the proton conductivity and the water sorption/desorption behaviour are also investigated to understand the relationship with wettability and surface energy and its components. Among the different methods, the van Oss acid-base and the modified Berthelot approaches yield comparable estimates for the total surface energy. (author)

76 FR 13982 - Antidumping Duty Order: Polyvinyl Alcohol From Taiwan

Science.gov (United States)

2011-03-15

...: Polyvinyl Alcohol From Taiwan AGENCY: Import Administration, International Trade Administration, Department... on polyvinyl alcohol (PVA) from Taiwan. DATES: Effective Date: March 15, 2011. FOR FURTHER... from Taiwan. See Polyvinyl Alcohol From Taiwan: Final Determination of Sales at Less Than Fair Value...

Swelling and mechanical properties of physically crosslinked poly(vinyl alcohol) hydrogels.

Science.gov (United States)

Suzuki, Atsushi; Sasaki, Saori

2015-12-01

Physically crosslinked poly(vinyl alcohol) gels are versatile biomaterials due to their excellent biocompatibility. In the past decades, physically crosslinked poly(vinyl alcohol) and poly(vinyl alcohol)-based hydrogels have been extensively studied for biomedical applications. However, these materials have not yet been implemented due to their mechanical strength. Physically crosslinked poly(vinyl alcohol) gels consist of a swollen amorphous network of poly(vinyl alcohol) physically crosslinked by microcrystallites. Although the mechanical properties can be improved to some extent by controlling the distribution of microcrystallites on the nano- and micro-scales, enhancing the mechanical properties while maintaining high water content remains very difficult. It may be technologically impossible to significantly improve the mechanical properties while keeping the gel's high water absorbance ability using conventional fabrication methods. Physical and chemical understandings of the swelling and mechanical properties of physically crosslinked poly(vinyl alcohol) gels are considered here; some promising strategies for their practical applications are presented. This review focuses more on the recent studies on swelling and mechanical properties of poly(vinyl alcohol) hydrogels, prepared using only poly(vinyl alcohol) and pure water with no other chemicals, as potential biomedical materials. © IMechE 2015.

Gum tragacanth-polyvinyl alcohol cryogel and xerogel blends for oral delivery of silymarin: Structural characterization and mucoadhesive property.

Science.gov (United States)

Niknia, Nushin; Kadkhodaee, Rassoul

2017-12-01

In this study silymarin (SM) loaded cryo- and xerogels of gum tragacanth-polyvinyl alcohol (GT-PVA) were prepared and their physico-mechanical, microstructural and release properties were investigated. The results showed that unlike cryogels, which were highly porous, xerogels exhibited a densely packed agglomerated microstructure with a continuous network of cracks. The bulk density, mechanical strength and SM retention of xerogels were also much higher than those of cryogels. Furthermore, it was revealed that increasing the ratio of GT adversely influenced both physico-mechanical and structural features of the dried gels, but improved the release profile of SM. Incorporation of SM into the gels led to a distinct enhancement in their porosity, microstructure and physical properties. Rheological measurements indicated that rising the ratio of GT and inclusion of SM increased the viscosity of mucin-polymers blend and improved mucoadhesive property of the gels. Copyright © 2017. Published by Elsevier Ltd.

Graphene oxide reinforced poly (4-styrenesulfonic acid)/polyvinyl alcohol blend composites with enhanced dielectric properties for portable and flexible electronics

Energy Technology Data Exchange (ETDEWEB)

Deshmukh, Kalim, E-mail: deshmukh.kalim@gmail.com [Department of Physics, B.S. Abdur Rahman University, Chennai, 600048, TN (India); Ahamed, M. Basheer [Department of Physics, B.S. Abdur Rahman University, Chennai, 600048, TN (India); Sadasivuni, Kishor Kumar [Mechanical and Industrial Engineering Department, Qatar University, P.O. Box 2713, Doha (Qatar); Ponnamma, Deepalekshmi; AlMaadeed, Mariam Al-Ali [Center for Advanced Materials, Qatar University, P.O. Box 2713, Doha (Qatar); Khadheer Pasha, S.K. [Department of Physics, School of Advanced Sciences, VIT University, Vellore, 632014, TN (India); Deshmukh, Rajendra R. [Department of Physics, Institute of Chemical Technology, Matunga, Mumbai, 400019 (India); Chidambaram, K. [Department of Physics, School of Advanced Sciences, VIT University, Vellore, 632014, TN (India)

2017-01-15

In this work, Graphene Oxide (GO) reinforced novel polymer composites comprising of poly (4-styrenesulfonic acid) (PSSA) and polyvinyl alcohol (PVA) blend matrix have been developed using colloidal processing technique. The properties and the structure of prepared composites were investigated using Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, X-ray diffraction (XRD), UV–vis spectroscopy (UV), Thermogravimetric analysis (TGA), Polarized optical microscopy (POM), Scanning electron microscopy (SEM) and Atomic force microscopy (AFM). The FTIR and Raman spectroscopy analysis indicate the strong interfacial interaction between GO and PSSA/PVA blend matrix. The XRD and SEM analysis confirm that GO was fully exfoliated into individual graphene sheets and dispersed homogeneously within the polymer matrix. The effective reinforcement of GO into PSSA/PVA blend matrix has resulted in the enhancement of dielectric constant. The dielectric constant has increased from 82.67 (50 Hz, 150 °C) for PSSA/PVA (50/50) blend to 297.91 (50 Hz, 150 °C) for PSSA/PVA/GO composites with 3 wt % GO loading. The dielectric loss (tan δ) has increased from 1.56 (50 KHz, 140 °C) for PSSA/PVA (50/50) blend to 2.64 (50 KHz, 140 °C) for PSSA/PVA/GO composites with 3 wt % GO loading. These findings provide a new insight to fabricate flexible, high-k dielectric composite as a promising material for energy storage applications. - Highlights: • Graphene Oxide was prepared from natural graphite using modified Hummers method. • Novel PSSA/PVA/GO composites were prepared by reinforcing GO into PSSA/PVA blend matrix. • Molecular level dispersion of GO in PSSA/PVA blend matrix was successfully achieved. • Enhancement in the dielectric constant was observed due to effective reinforcement of GO in PSSA/PVA blend matrix. • PSSA/PVA/GO composites with high dielectric performances can be considered for energy storage applications.

Novel carboxymethyl cellulose-polyvinyl alcohol blend films stabilized by Pickering emulsion incorporation method.

Science.gov (United States)

Fasihi, Hadi; Fazilati, Mohammad; Hashemi, Mahdi; Noshirvani, Nooshin

2017-07-01

The aim of this study was to investigate the possibility of increasing the antimicrobial and antioxidant properties of biodegradable active films stabilized via Pickering emulsions. The blend films were prepared from carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA), emulsified with oleic acid (OL) and incorporated with rosemary essential oil (REO). Formation of Pickering emulsion was confirmed by scanning electron microscopy (SEM), optical microscopy, mean droplet size and emulsion stability. Morphological, optical, physical, mechanical, thermal, antifungal and antioxidant properties of the films incorporated with different concentrations of REO (0.5, 1.5 and 3%) were determined. The results showed an increase in UV absorbance and elongation at break but, a decrease in tensile strength and thermal stability of the films. Interestingly, films containing REO exhibited considerable antioxidant and antimicrobial properties. In vitro microbial tests exhibited 100% fungal inhibition against Penicillium digitatum in the films containing 3% REO. In addition, no fungal growth were observed after 60days of storage at 25°C in bread slices were stored with active films incorporated with 3% REO, could attributed to the slow and regular release of REO caused by Pickering emulsions. The results of this study suggest that Pickering emulsion is a very promising method, which significantly affects antioxidant and antimicrobial activities of the films. Copyright © 2017 Elsevier Ltd. All rights reserved.

Complex compound polyvinyl alcohol-titanic acid/titanium dioxide

Science.gov (United States)

Prosanov, I. Yu.

2013-02-01

A complex compound polyvinyl alcohol-titanic acid has been produced and investigated by means of IR and Raman spectroscopy, X-ray diffraction, and synchronous thermal analysis. It is claimed that it represents an interpolymeric complex of polyvinyl alcohol and hydrated titanium oxide.

Preparation and Biodegradation of Nanocellulose Reinforced Polyvinyl Alcohol Blend Films in Bioenvironmental Media

OpenAIRE

Nusaiba Islam; Sharmin Jahan Proma; Ashiqur Rahman; Ashok Kumar Chakraborty

2017-01-01

Solution casting method was used to prepare nanocellulose reinforced polyvinyl alcohol (PVOH) from Oil palm empty fruit bunches. Different environmental test were used to investigate the biodegradability of the composite in soil and compost as well as in water and acidic solution. The morphology of the composite was investigated by scanning electron microscopy. The composite film with nanocellulose and without nanocellulose were compared, nanocellulose modified PVOH film showed more highly de...

Influence of kaolin addition on the dynamics of oxygen mass transport in polyvinyl alcohol dispersion coatings

OpenAIRE

Nyflött, Åsa; Axrup, Lars; Gunilla, Carlsson; Järnström, Lars; Lestelius, Magnus; Moons, Ellen; Wahlström, Torbjörn

2015-01-01

The permeability of dispersion barriers produced from polyvinyl alcohol (PVOH) and kaolin clay blends coated onto polymeric supports has been studied by employing two different measurement methods: the oxygen transmission rate (OTR) and the ambient oxygen ingress rate (AOIR). Coatings with different thicknesses and kaolin contents were studied. Structural information of the dispersion-barrier coatings was obtained by Fourier transform infrared spectroscopy (FTIR) spectroscopy and scanning ele...

Preparation and properties of poly(vinyl alcohol/chitosan blend bionanocomposites reinforced with cellulose nanocrystals/ZnO-Ag multifunctional nanosized filler

Directory of Open Access Journals (Sweden)

Azizi S

2014-04-01

Full Text Available Susan Azizi,1 Mansor Bin Ahmad,1 Mohd Zobir Hussein,1 Nor Azowa Ibrahim,1 Farideh Namvar2,31Department of Chemistry, Faculty of Science, 2Institute of Tropical Forestry and Forest Products, University Putra Malaysia, Selangor, Malaysia; 3Mashhad Branch, Islamic Azad University, Mashhad, IranAbstract: A series of novel bionanocomposites were cast using different contents of zinc oxide-silver nanoparticles (ZnO-AgNPs stabilized by cellulose nanocrystals (CNC as multifunctional nanosized fillers in poly(vinyl alcohol/chitosan (PVA/Cs matrices. The morphological structure, mechanical properties, ultraviolet-visible absorption, and antimicrobial properties of the prepared films were investigated as a function of their CNC/ZnO-AgNP content and compared with PVA/chitosan/CNC bionanocomposite films. X-ray diffraction and field emission scanning electron microscopic analyses showed that the CNC/ZnO-AgNPs were homogeneously dispersed in the PVA/Cs matrix and the crystallinity increased with increasing nanosized filler content. Compared with pure PVA/Cs, the tensile strength and modulus in the films increased from 0.055 to 0.205 GPa and from 0.395 to 1.20 GPa, respectively. Ultraviolet and visible light can be efficiently absorbed by incorporating ZnO-AgNPs into a PVA/Cs matrix, suggesting that these bionanocomposite films show good visibility and ultraviolet-shielding effects. The bionanocomposite films had excellent antimicrobial properties, killing both Gram-negative Salmonella choleraesuis and Gram-positive Staphylococcus aureus. The enhanced physical properties achieved by incorporating CNC/ZnO-AgNPs could be beneficial in various applications.Keywords: multifunctional nanofiller, bionanocomposite, cellulose nanocrystals, antimicrobial properties, poly(vinyl alcohol/chitosan blend

Radiation-chemical preparation of poly(vinyl alcohol) hydrogels

International Nuclear Information System (INIS)

Duflot, Anastasia V.; Kitaeva, Natalia K.; Duflot, Vladimir R.

2015-01-01

This work reports the usage of method of radiation-chemical synthesis to prepare cross-linked hydrogels from poly(vinyl alcohol) modified with glycidyl methacrylate. Synthesis kinetics of modified poly(vinyl alcohol) and properties of hydrogels were studied. The gel fraction, swelling, mechanical properties, and water content of the hydrogels were measured. It was found that gel fraction increases with increasing radiation dose, concentration of modified poly(vinyl alcohol), and reaches 60%. It was established by differential scanning calorimetry that a fraction of the “bound” water in hydrogels is 50–70% and independent of gel fraction content. In addition to “bound” and “free” states, water in hydrogels is also present in the intermediate state. - Highlights: • The synthesis and the properties of poly(vinyl alcohol) hydrogels were studied. • PVA was modified by glycidyl methacrylate before gamma cross-linking. • The modification results in decreasing of PVA cross-linking dose by 3 orders lower. • The gel fraction and water content of the hydrogels were measured. • A fraction of the “bound” water in hydrogels is independent of gel fraction content

Influence of acrylonitrile butadiene rubber on recyclability of blends prepared from poly(vinyl chloride) and poly(methyl methacrylate).

Science.gov (United States)

Suresh, Sunil S; Mohanty, Smita; Nayak, Sanjay K

2018-06-01

The current investigation deals with the recycling possibilities of poly(vinyl chloride) and poly(methyl methacrylate) in the presence of acrylonitrile butadiene rubber. Recycled blends of poly(vinyl chloride)/poly(methyl methacrylate) are successfully formed from the plastic constituents, those are recovered from waste computer products. However, lower impact performance of the blend and lower stability of the poly(vinyl chloride) phase in the recycled blend restricts its further usage in industrial purposes. Therefore, effective utilisation acrylonitrile butadiene rubber in a recycled blend was considered for improving mechanical and thermal performance. Incorporation of acrylonitrile butadiene rubber resulted in the improvement in impact performance as well as elongation-at-break of the recycled blend. The optimum impact performance was found in the blend with 9 wt% acrylonitrile butadiene rubber, which shows 363% of enhancement as compared with its parent blend. Moreover, incorporated acrylonitrile butadiene rubber also stabilises the poly(vinyl chloride) phase present in the recycled blend, similarly Fourier transform infrared spectroscopy studies indicate the interactions of various functionalities present in the recycled blend and acrylonitrile butadiene rubber. In addition to this, thermogravimetric analysis indicates the improvement in the thermal stability of the recycled blend after the addition of acrylonitrile butadiene rubber into it. The existence of partial miscibility in the recycled blend was identified using differential scanning calorimetry and scanning electron microscopy.

Papain wound dressings obtained from poly(vinyl alcohol)/calcium alginate blends as new pharmaceutical dosage form: Preparation and preliminary evaluation.

Science.gov (United States)

Dutra, J A P; Carvalho, S G; Zampirolli, A C D; Daltoé, R D; Teixeira, R M; Careta, F P; Cotrim, M A P; Oréfice, R L; Villanova, J C O

2017-04-01

Transparent, soft, flexible, mechanically resistant films, which are ideal for use as wound dressings were prepared in the presence of 2% papain, a proteolytic enzyme that can play a role in the chemical debridement of the skin and can accelerate the healing process. The films, based on poly(vinyl alcohol):calcium alginate blends with increasing concentrations of polysaccharide (10, 20, and 30% v/v), were obtained by casting method. FTIR and DSC analyses were performed to assess the composition and miscibility of blends. Mechanical properties such as tensile strength, elasticity modulus, and elongation at breakpoint were evaluated. The influence of different concentrations of calcium alginate on physical attributes of films like wettability, swelling capacity and mechanical properties was determined. The stability of papain in the films was assessed indirectly by hemolytic activity assay employing direct contact method and confirmed by technique based on blood agar diffusion. Preliminary cytotoxicity was evaluated with the XTT method. The results showed that at the polymer concentrations tested, the blends were miscible. The increase in the content of the calcium alginate increased the wettability and swelling capacity of the films, which is desirable in wound dressings. On the other hand, mechanical resistance decreased without causing breakage of the films during the swelling tests. The hemolytic activity of the films was maintained during the studied period, suggesting the stability of papain in the proposed formulations. Cellular viability indicated that the films were non-toxic. The analysis of the results showed that it is possible to prepare interactive and bioactive wound dressing containing papain from blends of PVA and calcium alginate polymers. Copyright © 2016 Elsevier B.V. All rights reserved.

Graphene oxide - Polyvinyl alcohol nanocomposite based electrode material for supercapacitors

Science.gov (United States)

Pawar, Pranav Bhagwan; Shukla, Shobha; Saxena, Sumit

2016-07-01

Supercapacitors are high capacitive energy storage devices and find applications where rapid bursts of power are required. Thus materials offering high specific capacitance are of fundamental interest in development of these electrochemical devices. Graphene oxide based nanocomposites are mechanically robust and have interesting electronic properties. These form potential electrode materials efficient for charge storage in supercapacitors. In this perspective, we investigate low cost graphene oxide based nanocomposites as electrode material for supercapacitor. Nanocomposites of graphene oxide and polyvinyl alcohol were synthesized in solution phase by integrating graphene oxide as filler in polyvinyl alcohol matrix. Structural and optical characterizations suggest the formation of graphene oxide and polyvinyl alcohol nanocomposites. These nanocomposites were found to have high specific capacitance, were cyclable, ecofriendly and economical. Our studies suggest that nanocomposites prepared by adding 0.5% wt/wt of graphene oxide in polyvinyl alcohol can be used an efficient electrode material for supercapacitors.

Graft copolymerization of styrene onto poly(vinyl alcohol) initiated by potassium diperiodatocuprate (III)

International Nuclear Information System (INIS)

Bai, L.; Wang, Ch.; Jin, J.; Liu, Y.

2009-01-01

The graft copolymerization of styrene onto poly(vinyl alcohol) is studied by using a novel redox system of potassium diperiodatocuprate-poly(vinyl alcohol) (Cu(III)poly(vinyl alcohol) in alkaline medium. Cu(III)-poly(vinyl alcohol) redox pair is an efficient initiator for this graft copolymerization which is proved by high graft efficiency (>97%) and high percentage of graft (>300%). Reaction conditions (monomer-to-poly(vinyl alcohol) weight ratio, initiator concentration, p H, time and temperature) affect the graft parameters which have been investigated systematically. The optimum reaction conditions are found as St/poly(vinyl alcohol) = 5.4; [Cu(III)] = 1*10 -2 M; p H = 12.7; temperature = 50 d eg C ; time = 3.5 h. Further, the equation of the overall polymerization rate can be written as follows: R p = k C 1.9 (St) C 1.7 (Cu(III)). The overall activation energy was calculated to be 42.0 kJ/mol based on the experimental data of the relations between R p and C(St); R p and C(Cu(III)); and R p and temperature. A mechanism is proposed to explain the formation of radicals and the initiation. The structure of the graft copolymers is confirmed by Fourier transfer infrared spectroscopy. Some peaks were compared with poly(vinyl alcohol) at 3080.34-3001.79 cm -1 (=C-H stretching in the phenyl ring), 1600.34-1450.95 cm -1 (C=C stretching in the phenyl ring), 755.17 cm -1 and 698.64 cm -1 (=C-H out-off-plane bending in phenyl ring) which are considered to belong to the characteristic absorption bands of phenyl group of polystyrene. Therefore it proves that the graft copolymer is composed of poly(vinyl alcohol) and polystyrene. thermal gravimetric analysis thermo grams of poly(vinyl alcohol) and poly(vinyl alcohol)-graft-polystyrene are investigated as well. As it is shown the initial decomposition temperature of poly(vinyl alcohol)-g-polystyrene(377.3 d eg C ) is much higher than that of poly(vinyl alcohol) (241.8 d eg C ), which indicates that the thermal stability of the

Polyvinyl alcohol composite nanofibres containing conjugated levofloxacin-chitosan for controlled drug release

International Nuclear Information System (INIS)

Jalvandi, Javid; White, Max; Gao, Yuan; Truong, Yen Bach; Padhye, Rajiv; Kyratzis, Ilias Louis

2017-01-01

A range of biodegradable drug-nanofibres composite mats have been reported as drug delivery systems. However, their main disadvantage is the rapid release of the drug immediately after application. This paper reports an improved system based on the incorporation of drug conjugated-chitosan into polyvinyl alcohol (PVA) nanofibers. The results showed that controlled release of levofloxacin (LVF) could be achieved by covalently binding LVF to low molecular weight chitosan (CS) via a cleavable amide bond and then blending the conjugated CS with polyvinyl alcohol (PVA) nanofibres prior to electrospinning. PVA/LVF and PVA-CS/LVF nanofibres were fabricated as controls. The conjugated CS-LVF was characterized by FTIR, DSC, TGA and 1 H NMR. Scanning electron microscopy (SEM) showed that the blended CS-PVA nanofibres had a reduced fibre diameter compared to the controls. Drug release profiles showed that burst release was decreased from 90% in the control PVA/LVF electrospun mats to 27% in the PVA/conjugated CS-LVF mats after 8 h in phosphate buffer at 37 °C. This slower release is due to the cleavable bond between LVF and CS that slowly hydrolysed over time at neutral pH. The results indicate that conjugation of the drug to the polymer backbone is an effective way of minimizing burst release behaviour and achieving sustained release of the drug, LVF. - Highlights: • A novel drug delivery system for controlled release of drug was designed. • Composite PVA/conjugated CS-LVF nanofibres was fabricated by electrospinning. • Conjugated chitosan and composite nanofibres were characterized by various techniques. • Release profiles of drug were significantly improved in composite nanofibres containing drug conjugated chitosan.

Polyvinyl alcohol composite nanofibres containing conjugated levofloxacin-chitosan for controlled drug release

Energy Technology Data Exchange (ETDEWEB)

Jalvandi, Javid, E-mail: Javid.jlv@gmail.com [CSIRO, Manufacturing Flagship, Bayview Ave, Clayton, Victoria 3168 (Australia); School of Fashion and Textiles, College of Design and Social Context, RMIT University, 25 Dawson Street, Brunswick, Victoria 3056 (Australia); White, Max, E-mail: tamrak@bigpond.com [School of Fashion and Textiles, College of Design and Social Context, RMIT University, 25 Dawson Street, Brunswick, Victoria 3056 (Australia); Gao, Yuan, E-mail: Yuan.Gao@csiro.au [CSIRO, Manufacturing Flagship, Bayview Ave, Clayton, Victoria 3168 (Australia); Truong, Yen Bach, E-mail: Yen.truong@csiro.au [CSIRO, Manufacturing Flagship, Bayview Ave, Clayton, Victoria 3168 (Australia); Padhye, Rajiv, E-mail: rajiv.padhye@rmit.edu.au [School of Fashion and Textiles, College of Design and Social Context, RMIT University, 25 Dawson Street, Brunswick, Victoria 3056 (Australia); Kyratzis, Ilias Louis, E-mail: Louis.kyratzis@csiro.au [CSIRO, Manufacturing Flagship, Bayview Ave, Clayton, Victoria 3168 (Australia)

2017-04-01

A range of biodegradable drug-nanofibres composite mats have been reported as drug delivery systems. However, their main disadvantage is the rapid release of the drug immediately after application. This paper reports an improved system based on the incorporation of drug conjugated-chitosan into polyvinyl alcohol (PVA) nanofibers. The results showed that controlled release of levofloxacin (LVF) could be achieved by covalently binding LVF to low molecular weight chitosan (CS) via a cleavable amide bond and then blending the conjugated CS with polyvinyl alcohol (PVA) nanofibres prior to electrospinning. PVA/LVF and PVA-CS/LVF nanofibres were fabricated as controls. The conjugated CS-LVF was characterized by FTIR, DSC, TGA and {sup 1}H NMR. Scanning electron microscopy (SEM) showed that the blended CS-PVA nanofibres had a reduced fibre diameter compared to the controls. Drug release profiles showed that burst release was decreased from 90% in the control PVA/LVF electrospun mats to 27% in the PVA/conjugated CS-LVF mats after 8 h in phosphate buffer at 37 °C. This slower release is due to the cleavable bond between LVF and CS that slowly hydrolysed over time at neutral pH. The results indicate that conjugation of the drug to the polymer backbone is an effective way of minimizing burst release behaviour and achieving sustained release of the drug, LVF. - Highlights: • A novel drug delivery system for controlled release of drug was designed. • Composite PVA/conjugated CS-LVF nanofibres was fabricated by electrospinning. • Conjugated chitosan and composite nanofibres were characterized by various techniques. • Release profiles of drug were significantly improved in composite nanofibres containing drug conjugated chitosan.

Properties of polyvinyl alcohol/xylan composite films with citric acid.

Science.gov (United States)

Wang, Shuaiyang; Ren, Junli; Li, Weiying; Sun, Runcang; Liu, Shijie

2014-03-15

Composite films of xylan and polyvinyl alcohol were produced with citric acid as a new plasticizer or a cross-linking agent. The effects of citric acid content and polyvinyl alcohol/xylan weight ratio on the mechanical properties, thermal stability, solubility, degree of swelling and water vapor permeability of the composite films were investigated. The intermolecular interactions and morphology of composite films were characterized by FTIR spectroscopy and SEM. The results indicated that polyvinyl alcohol/xylan composite films had good compatibility. With an increase in citric acid content from 10% to 50%, the tensile strength reduced from 35.1 to 11.6 MPa. However, the elongation at break increased sharply from 15.1% to 249.5%. The values of water vapor permeability ranged from 2.35 to 2.95 × 10(-7)g/(mm(2)h). Interactions between xylan and polyvinyl alcohol in the presence of citric acid become stronger, which were caused by hydrogen bond and ester bond formation among the components during film forming. Copyright © 2013. Published by Elsevier Ltd.

Inkjet-printed Polyvinyl Alcohol Multilayers.

Science.gov (United States)

Salaoru, Iulia; Zhou, Zuoxin; Morris, Peter; Gibbons, Gregory J

2017-05-11

Inkjet printing is a modern method for polymer processing, and in this work, we demonstrate that this technology is capable of producing polyvinyl alcohol (PVOH) multilayer structures. A polyvinyl alcohol aqueous solution was formulated. The intrinsic properties of the ink, such as surface tension, viscosity, pH, and time stability, were investigated. The PVOH-based ink was a neutral solution (pH 6.7) with a surface tension of 39.3 mN/m and a viscosity of 7.5 cP. The ink displayed pseudoplastic (non-Newtonian shear thinning) behavior at low shear rates, and overall, it demonstrated good time stability. The wettability of the ink on different substrates was investigated, and glass was identified as the most suitable substrate in this particular case. A proprietary 3D inkjet printer was employed to manufacture polymer multilayer structures. The morphology, surface profile, and thickness uniformity of inkjet-printed multilayers were evaluated via optical microscopy.

Preparation and Characterization of Formalated Polyvinyl Alcohol Hydrogel Film

International Nuclear Information System (INIS)

Than Than Aye; Nyunt Win; San Myint

2011-12-01

A feasible hydrogen film was prepared from polyvinyl alcohol (PVA) sample. The effect of chemical grafting on polyvinyl alcohol film was studied. Polyvinyl alcohol sample was mixed with distilled water and autoclaved at 121C for 60 minutes. An aqueous solution of polyvinyl alcohol was casted into a steel plate and dried for a certain time at room temperature. The obtained PVA film was immersed in formalation bath containing aqueous formaldehyde, sulphuric acid, anhydrous sodium sulphate with a weight ratio of (64:95:300) and 1 liter of distilled water at 60C for various hours. Effect of formalation time was studied varying 6, 12, 24, 36 and 48 hours. Degree of formalation was also evaluated. Physical properties of the hydrogel film such as gel fraction, degree of swelling and mechanical properties such as tensile strength, elongation and hardness were determined before and after formalation of the PVA film. Fourier Transform Infrared Spectroscopic (FTIR) analysis, Thermogravimetric / Differential thermal analysis (DTA / TG) were also studied for characterization. It was found that the appropriate condition for formalation was occured at 24 hours formalation time of with the calculated degree of formalation 65.35% with the determined values (9.04 Mpa) for tensile strength, (241.92%) for elongation, (45.30 Shore D) for hardness, (280.36%) for degree of swelling and (68.32%) for gel fraction.

Electrical and spectroscopic characterization of polyaniline-polyvinyl chloride (PANI-PVC) blends doped with sodium thiosulphate

International Nuclear Information System (INIS)

Ameen, Sadia; Ali, Vazid; Zulfequar, M.; Mazharul Haq, M.; Husain, M.

2008-01-01

Polyaniline is doped with sodium thiosulphate in aqueous tetrahydrofuran (THF) and the blended films have been prepared by changing the amount of doped polyaniline (PANI) in the fixed amount of polyvinyl chloride (PVC). The electrical conductivity of various samples of polyaniline-polyvinyl chloride (PANI-PVC) blends has been studied to see the effect of dopant in the temperature range 300-400 K. Mott's parameters are used to explain the conduction mechanism. Different parameters such as pre-exponential factor (σ 0 ), activation energy (ΔE) and T 0 have also been calculated to see the effect of chemical doping. The crystallinity of the blends is explained on the basis of T 0 . The calculated values of T 0 show that crystallinity increases with an increase of doped PANI in PANI-PVC blends. Fourier transform-infrared (FTIR) spectroscopy is done to explore the nature and interaction of dopant into the polymeric chain

Polyvinyl alcohol biodegradation under denitrifying conditions

Czech Academy of Sciences Publication Activity Database

Marušincová, H.; Husárová, L.; Růžička, J.; Ingr, M.; Navrátil, Václav; Buňková, L.; Koutný, M.

2013-01-01

Roč. 84, October (2013), s. 21-28 ISSN 0964-8305 Grant - others:GA ČR(CZ) GAP108/10/0200 Institutional support: RVO:61388963 Keywords : polyvinyl alcohol * biodegradation * denitrification * waste-water treatment * anaerobic * Steroidobacter Subject RIV: EI - Biotechnology ; Bionics Impact factor: 2.235, year: 2013

Polyvinyl alcohol hydrogels for iontohporesis

Science.gov (United States)

Bera, Prasanta; Alam, Asif Ali; Arora, Neha; Tibarewala, Dewaki Nandan; Basak, Piyali

2013-06-01

Transdermal therapeutic systems propound controlled release of active ingredients through the skin into the systemic circulation in a predictive manner. Drugs administered through these systems escape first-pass metabolism and maintain a steady state scenario similar to a continuous intravenous infusion for up to several days. The iontophoresis deal with the systemic delivery of the bioactive agents (drug) by applying an electric current. It is basically an injection without the needle. The iontophoretic system requires a gel-based matrix to accommodate the bioactive agent. Hydrogels have been used by many investigators in controlled-release drug delivery systems because of their good tissue compatibility and easy manipulation of swelling level and, thereby, solute permeability. In this work we have prepared polyvinyl alcohol (PVA) hydrogel. We have cross linked polyvinyl alcohol chemically with Glutaraldehyde with different wt%. FTIR study reveals the chemical changes during cross linking. Swelling in water, is done to have an idea about drug loading and drug release from the membrane. After drug loading to the hydrogels, we have studied the drug release property of the hydrogels using salicylic acid as a model drug.

Bond Performance and Structural Characterization of Polysaccharide Wood Adhesive Made from Konjac Glucomannan/Chitosan/Polyvinyl Alcohol

Directory of Open Access Journals (Sweden)

Rong Gu

2016-08-01

Full Text Available The bond performance and bonding mechanism were evaluated for a Konjac glucomannan (KGM, Chitosan (CS, and polyvinyl alcohol (PVOH blended wood adhesive. An optimized experimental strategy was used to investigate the effects of the formula parameters of adhesives on the bonding strength of plywood using a Box-Behnken design and response surface methodology (RSM. The microstructure of the blended adhesives was analyzed by Fourier transform infrared spectroscopy (FTIR and scanning electron microscopy (SEM. An optimum bonding strength (3.42 ± 0.31 MPa was achieved with concentrations of KGM, CS, and 10% PVOH of 2.3%, 2.3%, and 5.0%, respectively. There was strong hydrogen bonding between the KGM, CS, and 10% PVOH adhesives and the interface. SEM observations indicated that the blended adhesive exhibited a net-like structure that increased the overall bonding strength. These results provided the scientific basis for the continual development of environmentally friendly wood adhesives and the improvement of processing conditions.

Influence of Compounding Methods on Poly(vinyl) Alcohol/ Sago Pith Waste Bio composites: Mechanical and Water Absorption Properties

International Nuclear Information System (INIS)

Toh, W.Y.; Lai, J.C.; Aizan, W.A.R.W.

2011-01-01

Several methods of incorporating sago pith waste (SPW) into poly(vinyl alcohol) (PVA) had been conducted: (i) dry blending (PVA/SPW/G), (ii) blending of SPW and pre-plasticised PVA (pPVA/SPW/G) and (iii) blending of pre-plasticised of both PVA and SPW (pPVA/pSPW). The effect of the compounding method on the mechanical and water absorption properties were investigated. The addition of SPW into PVA greatly reduced the tensile strength and elongation at break. The tensile strength and elongation at break of PVA/SPW composites with identical geometry during compounding stage (powder/powder and pellet/pellet), which were PVA/SPW/G and pPVA/pSPW yielded the highest value. The percentage of water absorbed by PVA/SPW/G (without pre-plasticization) was the highest, followed by pPVA/pSPW and pPVA/SPW/G. (author)

Emissions characteristics of higher alcohol/gasoline blends

International Nuclear Information System (INIS)

Gautam, M.; Martin, D.W.; Carder, D.

2000-01-01

An experimental investigation was conducted to determine the emissions characteristics of higher alcohols and gasoline (UTG96) blends. While lower alcohols (methanol and ethanol) have been used in blends with gasoline, very little work has been done or reported on higher alcohols (propanol, butanol and pentanol). Comparisons of emissions and fuel characteristics between higher alcohol/gasoline blends and neat gasoline were made to determine the advantages and disadvantages of blending higher alcohols with gasoline. All tests were conducted on a single-cylinder Waukesha Cooperative Fuel Research engine operating at steady state conditions and stoichiometric air-fuel (A/F) ratio. Emissions test were conducted at the optimum spark timing-knock limiting compression ratio combination for the particular blend being tested. The cycle emission [mass per unit time (g/h)] of CO, CO 2 and organic matter hydrocarbon equivalent (OMHCE) from the higher alcohol/gasoline blends were very similar to those from neat gasoline. Cycle emissions of NO x from the blends were higher than those from neat gasoline. However, for all the emissions species considered, the brake specific emissions (g/kW h) were significantly lower for the higher alcohol/gasoline blends than for neat gasoline. This was because the blends had greater resistance to knock and allowed higher compression ratios, which increased engine power output. The contribution of alcohols and aldehydes to the overall OMHCE emissions was found to be minimal. Cycle fuel consumption (g/h) of higher alcohol/gasoline blends was slightly higher than with neat gasoline due to the lower stoichiometric A/F ratios required by the blends. However, the brake specific fuel consumption (g/kW h) for the blends was significantly lower than that for neat gasoline. (Author)

Poly(vinyl alcohol)-heparin hydrogels as sensor catheter membranes

NARCIS (Netherlands)

Brinkman, E.; van der Does, L.; Bantjes, A.

1991-01-01

Poly(vinyl alcohol)-heparin hydrogels with varying water content were synthesized for use as sensor catheter membranes. Films were cast from aqueous mixtures of poly(viny) alcohol) (PVA), a photosensitive cross-linker p-diazonium diphenyl amine polymer (PA), glutaraldehyde (GA) and heparin. After

Rheology and structure of aqueous bentonite–polyvinyl alcohol ...

Indian Academy of Sciences (India)

Keywords. Bentonite–polyvinyl alcohol dispersions; rheology; zeta potential; particle size analysis; SEM; FTIR studies. 1. .... sity and interception of the linear portion of the curve ..... applications for decolourizing or moisture absorption purpose.

Effects of Saponification Rate on Electrooptical Properties and Morphology of Poly(vinyl alcohol)/Liquid Crystal Composite Films

Science.gov (United States)

Ono, Hiroshi; Kawatsuki, Nobuhiro

1995-03-01

The relationship between the saponification rate of poly(vinyl alcohol) (PVA), and the electrooptical properties and morphology of the PVA/liquid crystal (LC) composite films was investigated. Light transmission clazing and the LC droplet size were varied by changing the saponification rate or the blend ratio of two kinds of PVA with different saponification rates because the refractive index and surface tension could be controlled by the saponification rate of PVA. The threshold voltage decreased with increasing saponification rate though the extrapolation length was decreased. It was suggested that the electrooptical properties were strongly dependent on the droplet size.

Enhanced mechanical, thermal and antimicrobial properties of poly(vinyl alcohol)/graphene oxide/starch/silver nanocomposites films.

Science.gov (United States)

Usman, Adil; Hussain, Zakir; Riaz, Asim; Khan, Ahmad Nawaz

2016-11-20

In the present work, synthesis of poly(vinyl alcohol)/graphene oxide/starch/silver (PVA/GO/Starch/Ag) nanocomposites films is reported. Such films have been characterized and investigated for their mechanical, thermal and antimicrobial properties. The exfoliation of GO in the PVA matrix occurs owing to the non-covalent interactions of the polymer chains of PVA and hydrophilic surface of the GO layers. Presence of GO in PVA and PVA/starch blends were found to enhance the tensile strength of the nanocomposites system. It was found that the thermal stability of PVA as well as PVA/starch blend systems increased by the incorporation of GO where strong physical bonding between GO layers and PVA/starch blends is assumed to cause thermal barrier effects. Antimicrobial properties of the prepared films were investigated against Escherichia coli and Staphylococcus aureus. Our results show enhanced antimicrobial properties of the prepared films where PVA-GO, PVA-Ag, PVA-GO-Ag and PVA-GO-Ag-Starch showed antimicrobial activity in ascending order. Copyright © 2016 Elsevier Ltd. All rights reserved.

Preparation and characterization of oriented poly(vinyl alcohol)/carbon nanotube composite nanofibers

Science.gov (United States)

Shimizu, Akikazu; Kato, Hayato; Sato, Taiga; Kushida, Masahito

2017-07-01

Oriented nanofiber mats blended with carbon nanotubes (CNTs) are expected to be applied as cell seeding scaffolds. Biomaterials that are often used for cell seeding scaffolds generally have low mechanical strength and low electrical conductivity; thus, it has been difficult to apply them to tissues such as heart and nerve. In this study, we prepared oriented poly(vinyl alcohol) (PVA) nanofiber mats blended with various CNT concentrations (up to 10 wt %) by electrospinning using the parallel plate electrodes as collectors with applied voltage. The morphology, mechanical properties, and electrical properties of the prepared oriented nanofiber mats were measured by using various techniques such as scanning electron microscopy (SEM). The tensile strength of the oriented nanofiber mats in the applied voltage direction increased from 2.5 to 9.7 MPa with CNT concentration. Furthermore, the electrical conductivity of the oriented nanofiber mats in the applied voltage direction increased from 0.67 × 10-7 to 4.3 × 10-7 S·m-1. Also, the mechanical strength and electrical conductivity of the oriented nanofiber mats in the applied voltage direction were 3-4 and 2-3 times higher than those in the perpendicular direction, respectively.

Effect of phosphorous-containing modified poly(vinyl alcohol on the mechanical and flame retardant properties of polypropylene

Directory of Open Access Journals (Sweden)

S. Sauca

2015-04-01

Full Text Available Blends of polypropylene (PP and different phosphorous-modified poly(vinyl alcohol (PVA derivatives synthesized on purpose, were prepared by both solvent and melt mixing, and fully characterized. Thermogravimetric analysis showed that the addition of the phosphorous-modified PVAs significantly increased thermal stability and charring of PP, probably due to their dehydration and the subsequent formation of a protective layer onto PP. SEM analysis demonstrated poor phase compatibility between PP and the polymeric additives, however acceptable dispersion of the polymeric additives was obtained. It was also observed that grafting of the modified PVA on PP occurred due to radical reactions arising during melt processing. Mechanical characterization showed that the elastic behavior of the blends was not altered with respect to neat PP, while ductility was reduced; on the other hand, impact resistance was considerably improved by blending. Slightly higher LOI values were obtained for the blends even with phosphorous content as small as 1 wt%; reduced dripping was also observed during the burning tests for the blend samples. Moreover, cone calorimeter test results showed that heat release rate, total heat release, and fire growth rate decreased compared with PP, in particular for the blends containing residual –OH groups on the PVA backbone. Therefore, these blends can find application where the combination of toughness and fire retardancy is required, such as in the automotive industry.

Crystallisation of hydroxyapatite in phosphorylated poly(vinyl alcohol) as a synthetic route to tough mechanical hybrid materials

International Nuclear Information System (INIS)

Kusakabe, Akane; Hirota, Ken; Mizutani, Tadashi

2017-01-01

Partially phosphorylated poly(vinyl alcohol) was prepared by treating poly(vinyl alcohol) with 100% phosphoric acid, and 5, 10 and 20% of the hydroxyl groups were converted to phosphoric acid ester. Addition of Ca 2+ to an aqueous solution of phosphorylated poly(vinyl alcohol) gave a transparent gel. Five cycles of alternate soaking of the gel in aqueous CaCl 2 and aqueous (NH 4 ) 2 HPO 4 were carried out to crystallise hydroxyapatite (HAP) in the phosphorylated poly(vinyl alcohol) matrix. The X-ray diffraction peaks of HAP formed in 5% phosphorylated PVA were sharp, while those of HAP formed in 20% phosphorylated PVA were broad. The contents of inorganic phase in the hybrid powder were increased from 58 to 76 wt% as the fraction of phosphate groups in the gel was decreased from 20% to 5%. The hybrid powder was first subjected to uniaxial pressing, followed by cold isostatic pressing (CIP) and warm isostatic pressing (WIP) at 120 °C at pressures of 300–980 MPa, to obtain the specimens for three-point bending test. These hybrid specimens showed bending strengths of 15–53 MPa. The hybrid compacts prepared from 10% phosphorylated poly(vinyl alcohol) showed the smallest Young's modulus, the largest displacement at break, and the largest fracture energy, showing that it has the highest toughness among the hybrid materials prepared from poly(vinyl alcohol) with varying degrees of phosphorylation. - Graphical abstract: Densification of hydroxyapatite crystallised in 10% phosphorylated poly(vinyl alcohol) gave the toughest compact. - Highlights: • Hydroxyapatite was crystallised in phosphorylated poly(vinyl alcohol) gels. • Crystallite size of hydroxyapatite decreased as phosphate density was increased. • The hybrid specimens prepared in 10% phosphorylated gel was the toughest. • Phosphate density in organic matrix regulated the mechanical properties of the hybrid.

Crystallisation of hydroxyapatite in phosphorylated poly(vinyl alcohol) as a synthetic route to tough mechanical hybrid materials

Energy Technology Data Exchange (ETDEWEB)

Kusakabe, Akane; Hirota, Ken; Mizutani, Tadashi, E-mail: tmizutan@mail.doshisha.ac.jp

2017-01-01

Partially phosphorylated poly(vinyl alcohol) was prepared by treating poly(vinyl alcohol) with 100% phosphoric acid, and 5, 10 and 20% of the hydroxyl groups were converted to phosphoric acid ester. Addition of Ca{sup 2+} to an aqueous solution of phosphorylated poly(vinyl alcohol) gave a transparent gel. Five cycles of alternate soaking of the gel in aqueous CaCl{sub 2} and aqueous (NH{sub 4}){sub 2}HPO{sub 4} were carried out to crystallise hydroxyapatite (HAP) in the phosphorylated poly(vinyl alcohol) matrix. The X-ray diffraction peaks of HAP formed in 5% phosphorylated PVA were sharp, while those of HAP formed in 20% phosphorylated PVA were broad. The contents of inorganic phase in the hybrid powder were increased from 58 to 76 wt% as the fraction of phosphate groups in the gel was decreased from 20% to 5%. The hybrid powder was first subjected to uniaxial pressing, followed by cold isostatic pressing (CIP) and warm isostatic pressing (WIP) at 120 °C at pressures of 300–980 MPa, to obtain the specimens for three-point bending test. These hybrid specimens showed bending strengths of 15–53 MPa. The hybrid compacts prepared from 10% phosphorylated poly(vinyl alcohol) showed the smallest Young's modulus, the largest displacement at break, and the largest fracture energy, showing that it has the highest toughness among the hybrid materials prepared from poly(vinyl alcohol) with varying degrees of phosphorylation. - Graphical abstract: Densification of hydroxyapatite crystallised in 10% phosphorylated poly(vinyl alcohol) gave the toughest compact. - Highlights: • Hydroxyapatite was crystallised in phosphorylated poly(vinyl alcohol) gels. • Crystallite size of hydroxyapatite decreased as phosphate density was increased. • The hybrid specimens prepared in 10% phosphorylated gel was the toughest. • Phosphate density in organic matrix regulated the mechanical properties of the hybrid.

76 FR 13660 - Polyvinyl Alcohol From Taiwan

Science.gov (United States)

2011-03-14

... Taiwan Determination On the basis of the record \\1\\ developed in the subject investigation, the United... Act of 1930 (19 U.S.C. 1673d(b)) (the Act), that an industry in the United States is materially injured by reason of imports from Taiwan of polyvinyl alcohol, provided for under subheading 3905.30.00 of...

Biodegradation behaviors and water adsorption of poly(vinyl alcohol)/starch/carboxymethyl cellulose/clay nanocomposites

Science.gov (United States)

Taghizadeh, Mohammad Taghi; Sabouri, Narges

2013-09-01

The focus of this work is to study the effect of sodium montmorillonite (MMT-Na) clay content on the rate and extent of enzymatic hydrolysis polyvinyl alcohol (PVA)/starch (S)/carboxymethyl cellulose (CMC) blends using enzyme cellulase. The rate of glucose production from each nanocomposite substrates was most rapid for the substrate without MMT-Na and decreased with the addition of MMT-Na for PVA/S/CMC blend (51.5 μg/ml h), PVA/S/CMC/1% MMT (45.4 μg/ml h), PVA/S/CMC/3% MMT (42.8 μg/ml h), and PVA/S/CMC/5% MMT (39.2 μg/ml h). The results of this study have revealed that films with MMT-Na content at 5 wt.% exhibited a significantly reduced rate and extent of hydrolysis. Enzymatic degradation behavior of MMT-Na containing nanocomposites of PVA/S/CMC was based on the determinations of weight loss and the reducing sugars. The degraded residues have been characterized by various analytical techniques, such as Fourier transform infrared spectroscopy, scanning electronic microscopy, and UV-vis spectroscopy.

Ultraviolet sensing properties of polyvinyl alcohol-coated aluminium ...

Indian Academy of Sciences (India)

Undoped and aluminium (Al)-doped zinc oxide (ZnO) nanorods have been synthesized by electrochemical route. The synthesized materials have been characterized by X-ray diffraction, UV–visible spectrometer and scanning electron microscope. The Al-doped ZnO nanorods have been coated with polyvinyl alcohol.

Effect of gamma radiation on the physical and chemical properties of some polymer blends

International Nuclear Information System (INIS)

Ibrahim, S.M.

2000-01-01

this work has been carried out to investigate the characterization of poly(vinyl alcohol) (PVA) / carboxymethyl cellulose (CMC) polymer blends exposed to various doses of gamma radiation has been investigated . the application of this blend after grafting with styrene monomer in absorbing waste dye from waste water was also studied . moreover, the effect of glycerol as a plasticizer on the structure property behavior of the same blend was reported. finally, the structure -property behavior of gamma and electron beam irradiated polyvinyl chloride (PVC) / nitrile butadiene rubber (NBR) was investigated

Composite poly(vinyl alcohol/poly(vinyl acetate electrospun nanofibrous mats as a novel wound dressing matrix for controlled release of drugs

Directory of Open Access Journals (Sweden)

Jannesari M

2011-05-01

Full Text Available Marziyeh Jannesari1, Jaleh Varshosaz2, Mohammad Morshed1, Maedeh Zamani11Department of Textile Engineering, Isfahan University of Technology, Isfahan, Iran; 2Department of Pharmaceutics, School of Pharmacy and Pharmaceutical Sciences Research Center, Isfahan University of Medical Sciences, Isfahan, IranAbstract: The aim of this study was to develop novel biomedicated nanofiber electrospun mats for controlled drug release, especially drug release directly to an injury site to accelerate wound healing. Nanofibers of poly(vinyl alcohol (PVA, poly(vinyl acetate (PVAc, and a 50:50 composite blend, loaded with ciprofloxacin HCl (CipHCl, were successfully prepared by an electrospinning technique for the first time. The morphology and average diameter of the electrospun nanofibers were investigated by scanning electron microscopy. X-ray diffraction studies indicated an amorphous distribution of the drug inside the nanofiber blend. Introducing the drug into polymeric solutions significantly decreased solution viscosities as well as nanofiber diameter. In vitro drug release evaluations showed that both the kind of polymer and the amount of drug loaded greatly affected the degree of swelling, weight loss, and initial burst and rate of drug release. Blending PVA and PVAc exhibited a useful and convenient method for electrospinning in order to control the rate and period of drug release in wound healing applications. Also, the thickness of the blend nanofiber mats strongly influenced the initial release and rate of drug release.Keywords: biodegradable polymers, drug delivery, controlled release, electrospun nanofibers, wound dressing

Stability of polyvinyl alcohol-coated biochar nanoparticles in brine

Energy Technology Data Exchange (ETDEWEB)

Griffith, Christopher, E-mail: cgriffith@utexas.edu; Daigle, Hugh [University of Texas at Austin, Department of Petroleum and Geosystems Engineering (United States)

2017-01-15

This paper reports on the dispersion stability of 150 nm polyvinyl alcohol coated biochar nanoparticles in brine water. Biochar is a renewable, carbon based material that is of significant interest for enhanced oil recovery operations primarily due to its wide ranging surface properties, low cost of synthesis, and low environmental toxicity. Nanoparticles used as stabilizing agents for foams (and emulsions) or in nanofluids have emerged as potential alternatives to surfactants for subsurface applications due to their improved stability at reservoir conditions. If, however, the particles are not properly designed, they are susceptible to aggregation because of the high salinity brines typical of oil and gas reservoirs. Attachment of polymers to the nanoparticle surface, through covalent bonds, provides steric stabilization, and is a necessary step. Our results show that as the graft density of polyvinyl alcohol increases, so too does the stability of nanoparticles in brine solutions. A maximum of 34 wt% of 50,000 Da polyvinyl alcohol was grafted to the particle surface, and the size of the particles was reduced from ~3500 nm (no coating) to 350 nm in brine. After 24 h, the particles had a size of ~500 nm, and after 48 h completely aggregated. 100,000 Da PVA coated at 24 wt% on the biochar particles were stable in brine for over 1 month with no change in mean particle size of ~330 nm.

FT-IR study of gamma-radiation induced degradation of polyvinyl alcohol (PVA) and PVA/humic acids blends

International Nuclear Information System (INIS)

Ilcin, M.; Hola, O.; Bakajova, B.; Kucerik, J.

2010-01-01

Samples of pure polyvinyl alcohol (PVA) and PVA doped with humic acids were exposed to gamma radiation. Gamma rays induced the degradation of the pure polymer. Degradation changes were observed using ATR FT-IR equipment. Dehydration, double bond creation, and their subsequent oxidation (surrounding atmosphere was air) were found out. Also, other degradation reactions (e.g. chain scission, cyclization) occur simultaneously. Formation of C=C and C=O bonds is apparent from FT-IR spectra. In contrast the presence of humic acids in the PVA sample showed stabilizing effect on PVA structure within the concentration range 0.5-10%. (author)

75 FR 15726 - Polyvinyl Alcohol From Taiwan; Determination

Science.gov (United States)

2010-03-30

... an industry in the United States is materially injured by reason of imports from Taiwan of polyvinyl.... industry was materially injured or threatened with material injury by reason of imports of PVA from Taiwan... Alcohol From Taiwan; Determination On the basis of the record \\1\\ developed in the subject investigation...

Chemical modification of poly(vinyl alcohol): evaluation of hydrophilic/lipophilic balance

International Nuclear Information System (INIS)

Aranha, Isabele B.; Lucas, Elizabete F.

2001-01-01

Poly(vinyl alcohol) terpolymers have been obtained by reaction of partially hydrolized poly(vinyl alcohol) with different acid chlorides. The objective is the preparation of polymers with slight differences in their hydrophilic/lipophilic balance and in the interfacial activities of their solutions. The chemical modifications were characterized by means of 1 H NMR and the polymer properties were evaluated in terms of changes in solubility and surface tension. By chemical modification, polymers with low percentage of hydrophobic group were obtained. The water-soluble polymers obtained did not have the surface tension of their solutions altered. The solubility of the modified polymers decreased markedly, even with low contents of hydrophobic groups. (author)

Biodegradation of blend films PVA/PVC, PVA/PCL in soil and soil with landfill leachate

Directory of Open Access Journals (Sweden)

Adriana de Campos

2011-12-01

Full Text Available This study investigated the biodegradation of blends films of poly(vinyl alcohol/poly(vinyl chloride (PVA/PVC and poly(vinyl alcohol/poly(caprolactone (PVA/PCL blends films prepared with dimethylformamide under a variety of conditions by respirometry, spectrophotometry (FTIR, scanning electron microscopy (SEM, and contact angle. The films were buried in the garden soil and in the soil mixed with the landfill leachate for 120 days at 28ºC. Significant levels of biodegradation were achieved in fairly short incubation times in the soil. The results indicated that PVA was the most biodegradable film in the soil and in the soil with the leachate.

Surface Properties of a Novel Poly(vinyl alcohol Film Prepared by Heterogeneous Saponification of Poly(vinyl acetate Film

Directory of Open Access Journals (Sweden)

Seong Baek Yang

2017-10-01

Full Text Available Almost general poly(vinyl alcohol (PVA films were prepared by the processing of a PVA solution. For the first time, a novel poly(vinyl alcohol (PVA film was prepared by the saponification of a poly(vinyl acetate (PVAc film in a heterogenous medium. Under the same saponification conditions, the influence of saponification time on the degree of saponification (DS was studied for the preparation of the saponified PVA film, and it was found that the DS varied with time. Optical microscopy was used to confirm the characteristics and surface morphology of the saponified PVA film, revealing unusual black globules in the film structure. The contact angle of the films was measured to study the surface properties, and the results showed that the saponified PVA film had a higher contact angle than the general PVA film. To confirm the transformation of the PVAc film to the PVA film, 1H nuclear magnetic resonance spectroscopy, X-ray diffraction measurements, differential scanning calorimetry, and Fourier-transform infrared spectroscopy were employed.

Polyvinyl alcohol/chitosan/montmorillonite nanocomposites preparation by freeze/thaw cycles and characterization

Directory of Open Access Journals (Sweden)

Părpăriţă Elena

2014-12-01

Full Text Available Polyvinyl alcohol (PVA and chitosan (CS based hydrogels are often chosen to obtain hydrogels as being considered non-toxic for human body. The present study aims the preparation and physical chemical characterisation of hydrogels based PVA and CS by using an environmental friendly method i.e. freeze/thaw. In this method the only parameters affecting the hydrogels’ properties is the PVA concentration in solution, time and number of cycles of freezing / thawing. Repeated freezing and thawing cycles resulted in production of a highly elastic polyvinyl alcohol hydrogel with higher degree of crystallization. Adding chitosan in polyvinyl alcohol hydrogel is giving to the newly formed material, biocompatibility and antibacterial properties due to the free amino groups of chitosan. Higher mechanical and thermal characteristics of PVA/CS based hydrogels were obtained by addition of a small amount of inorganic nanoparticles (montmorillonite clay, C30B into the matrix (i.e. 1%. Scanning electron microscopy (SEM, Fourier transform infrared spectroscopy (FT-IR, near-infrared chemical imaging spectroscopy (NI-CI, X-ray diffraction (XRD, thermogravimetric analysis (TG, swelling and rheological measurements were used to characterize the polyvinyl alcohol/chitosan/montmorillonite properties. The swelling degree increased with decreasing chitosan content in hydrogels and the variation is opposite in nanocomposites, decreasing after introducing the nanoclay. The swelling behaviour was influenced by the presence of the nanoparticles. The plasticizer effect of the nanoparticles was reflected by obtaining a more compact hydrogel network with higher mechanical and thermal properties. The proposed materials can be a promising alternative in biomedical applications

Poly(vinyl alcohol) gels as photoacoustic breast phantoms revisited

NARCIS (Netherlands)

Xia, Wenfeng; Piras, Daniele; Heijblom, Michelle; Steenbergen, Wiendelt; van Leeuwen, Ton G.; Manohar, Srirang

2011-01-01

A popular phantom in photoacoustic imaging is poly(vinyl alcohol) (PVA) hydrogel fabricated by freezing and thawing (F-T) aqueous solutions of PVA. The material possesses acoustic and optical properties similar to those of tissue. Earlier work characterized PVA gels in small test specimens where

Poly(vinyl alcohol) gels as photoacoustic breast phantoms revisited

NARCIS (Netherlands)

Xia, W.; Piras, D.; Heijblom, M.; Steenbergen, Wiendelt; van Leeuwen, Ton; Manohar, Srirang

2011-01-01

A popular phantom in photoacoustic imaging is poly(vinyl alcohol) (PVA) hydrogel fabricated by freezing and thawing (F–T) aqueous solutions of PVA. The material possesses acoustic and optical properties similar to those of tissue. Earlier work characterized PVA gels in small test specimens where

Morphology in binary blends of poly(vinyl methyl ether) and epsilon-caprolactone-trimethylene carbonate diblock copolymer

NARCIS (Netherlands)

Luyten, MC; Bogels, EJF; vanEkenstein, GORA; tenBrinke, G; Bras, W; Komanschek, BE; Ryan, AJ

The morphology of symmetric diblock copolymer of epsilon-caprolactone (PCL) and trimethylene carbonate (PTMC), in blends with poly(vinyl methyl ether) (PVME) is investigated with (modulated) differential scanning calorimetry (d.s.c.), time resolved small angle (SAXS) and wide angle (WAXS) X-ray

Morphology in binary blends of poly(vinyl methyl ether) and ε-caprolactone-trimethylene carbonate diblock copolymer

NARCIS (Netherlands)

Luyten, M.C.; Bögels, E.J.F.; Alberda van Ekenstein, G.O.R.; Brinke, G. ten; Bras, W.; Komanschek, B.E.; Ryan, A.J.

1997-01-01

The morphology of symmetric diblock copolymer of ε-caprolactone (PCL) and trimethylene carbonate (PTMC), in blends with poly(vinyl methyl ether) (PVME) is investigated with (modulated) differential scanning calorimetry (d.s.c.), time resolved small angle (SAXS) and wide angle (WAXS) X-ray

Rheology and structure of aqueous bentonite–polyvinyl alcohol ...

Indian Academy of Sciences (India)

Abstract. The influence of polymer on flow behaviour of Balikesir, Turkey bentonite dispersions (2%, w/w) was studied for non-ionic polymer, polyvinyl alcohol (PVA). In a range of 3⋅3 × 10–6 – 3⋅3 × 105 mol/l, PVA was added to the bentonite dispersions in different concentrations and its behaviour was observed on ...

Artificial Auricular Cartilage Using Silk Fibroin and Polyvinyl Alcohol Hydrogel

Science.gov (United States)

Lee, Jung Min; Sultan, Md. Tipu; Kim, Soon Hee; Kumar, Vijay; Yeon, Yeung Kyu; Lee, Ok Joo; Park, Chan Hum

2017-01-01

Several methods for auricular cartilage engineering use tissue engineering techniques. However, an ideal method for engineering auricular cartilage has not been reported. To address this issue, we developed a strategy to engineer auricular cartilage using silk fibroin (SF) and polyvinyl alcohol (PVA) hydrogel. We constructed different hydrogels with various ratios of SF and PVA by using salt leaching, silicone mold casting, and freeze-thawing methods. We characterized each of the hydrogels in terms of the swelling ratio, tensile strength, pore size, thermal properties, morphologies, and chemical properties. Based on the cell viability results, we found a blended hydrogel composed of 50% PVA and 50% SF (P50/S50) to be the best hydrogel among the fabricated hydrogels. An intact 3D ear-shaped auricular cartilage formed six weeks after the subcutaneous implantation of a chondrocyte-seeded 3D ear-shaped P50/S50 hydrogel in rats. We observed mature cartilage with a typical lacunar structure both in vitro and in vivo via histological analysis. This study may have potential applications in auricular tissue engineering with a human ear-shaped hydrogel. PMID:28777314

Effects of Modified Iron Oxide Nanoparticles on the Thermal and Dynamic Mechanical Properties of Cellulose Poly(vinyl alcohol Blend Films

Directory of Open Access Journals (Sweden)

Mehdi Roohani

2015-11-01

Full Text Available This study was designed to investigate the effect of modified iron oxide nanoparticles (MINP and cellulose nanocrystals (NCC on magnetic, thermal and dynamic-mechanical properties of poly(vinyl alcohol based nanocomposites. Fe3O4 nanoparticles have been synthesized using a chemical co-precipitation route. Nanocomposite films were developed by solvent casting method and their properties were characterized by vibrating sample magnetometer (VSM, differential scanning calorimetry (DSC and dynamic mechanical analysis (DMA. DSC results found that with incorporation of nanoparticles, the glass transition temperature increase slightly to higher temperatures; however, the degree of crystallinity and the values of the melting temperature are found to decrease. Dynamic mechanical analysis revealed that, at the elevated temperatures, improvement of mechanical properties due to the presence of nanoparticles was even more noticeable. Addition of nanoparticles resulted in increased thermal stability of PVA due to the reduction in mobility of matrix molecules by strong hydrogen bonds between nanocomposite components. Results indicated that, MINP and NCC have synergistic effect on improving of poly(vinyl alcohol properties. The VSM findings showed that the saturation magnetization of iron oxide nanoparticles reduced after modification. This can be attributed to formation of hydroxyapatite on nanoparticles surface. The saturation magnetization (Ms of PVA- MINP films was higher than PVA-MINP- NCC film. This result probably is related to more amount of magnetic nanoparticles in PVA-MINP films.

pH sensitivity of emeraldine salt polyaniline and poly(vinyl butyral) blend

International Nuclear Information System (INIS)

Nguyen, Hoa Duyen; Hoang, Ngoc Vu; Le, Nguyen Ngan; Nguyen, Thi Ngoc Nhien; Doan, Duc Chanh Tin; Dang, Mau Chien; Nguyen, Thi Ha

2014-01-01

pH sensitivity of emeraldine salt polyaniline (ES-PANI) and poly(vinyl butyral) (PVB) blend film was investigated. This blend film can be used as a pH sensing element in new-type pH sensors to replace traditional instruments based on fragile glass electrodes for pH measurement of water in aquaculture farming. Structural and optical characteristic of PANI were studied by Fourier transform infrared spectroscopy (FTIR) and ultraviolet visible spectroscopy (UV–vis). Electrical characterization of ES-PANI:PVB blend films versus pH was performed with chemiresistors fabricated by micro-lithography. A ES-PANI:PVB layer was drop-coated on comb-shaped platinum electrodes patterned on SiO 2 /Si substrates. Scanning electron microscope (SEM) and optical microscope were used to investigate morphology of the fabricated platinum electrodes and the coated polymer blend films. I–V measurements of the polymer-coated chemiresistors were performed at very low relative humidity after the polymer films were exposed to pH 1–8. The results showed that logarithm of electrical resistance of the ES-PANI:PVB films increased almost linearly as pH increased from 1 to 8. The initial results showed that the PANI blend-coated chemiresistors can be used as pH sensors for water quality monitoring. (paper)

The Effects of Reaction Variables on Solution Polymerization of Vinyl Acetate and Molecular Weight of Poly(vinyl alcohol Using Taguchi Experimental Design

Directory of Open Access Journals (Sweden)

M.H. Navarchian

2009-12-01

Full Text Available Poly(vinyl acetate is synthesized via solution polymerization, and then it is converted to poly(vinyl alcohol by alkaline alcoholysis. The aim of the work study was to investigate statistically the  influence of reaction variables in vinyl acetate polymerization, the conversion of this monomer to polymer, degree of branching of acetyl group in poly(vinyl acetate, as well as the molecular weight of poly(vinyl alcohol, using Taguchi experimental design approach. The reaction variables were polymerization time, molar ratio of initiator to monomer, and volume ratio of monomer to solvent. The statistical analysis of variance of the results revealed that all factors have significantly influenced the conversion and degree of branching. Volume ratio of monomer to solvent is the only factor affecting the molecular weight of poly(vinyl alcohol, and has the greatest influence on all responses. By increasing this ratio, the conversion, degree of branching of acetyl group in poly(vinyl acetate, and molecular weight of poly(vinyl alcohol were increased.

FTIR studies of plasticized poly(vinyl alcohol)-chitosan blend doped with NH 4NO 3 polymer electrolyte membrane

Science.gov (United States)

Kadir, M. F. Z.; Aspanut, Z.; Majid, S. R.; Arof, A. K.

2011-03-01

Fourier transform infrared (FTIR) spectroscopy studies of poly(vinyl alcohol) (PVA), and chitosan polymer blend doped with ammonium nitrate (NH 4NO 3) salt and plasticized with ethylene carbonate (EC) have been performed with emphasis on the shift of the carboxamide, amine and hydroxyl bands. 1% acetic acid solution was used as the solvent. It is observed from the chitosan film spectrum that evidence of polymer-solvent interaction can be observed from the shifting of the carboxamide band at 1660 cm -1 and the amine band at 1591 cm -1 to 1650 and 1557 cm -1 respectively and the shift of the hydroxyl band from 3377 to 3354 cm -1. The hydroxyl band in the spectrum of PVA powder is observed at 3354 cm -1 and is observed at 3343 cm -1 in the spectrum of the PVA film. On addition of NH 4NO 3 up to 30 wt.%, the carboxamide, amine and hydroxyl bands shifted from 1650, 1557 and 3354 cm -1 to 1642, 1541 and 3348 cm -1 indicating that the chitosan has complexed with the salt. In the PVA-NH 4NO 3 spectrum, the hydroxyl band has shifted from 3343 to 3272 cm -1 on addition of salt from 10 to 30 wt.%. EC acts as a plasticizing agent since there is no shift in the bands as observed in the spectrum of PVA-chitosan-EC films. The mechanism of ion migration is proposed for the plasticized and unplasticized PVA-chitosan-NH 4NO 3 systems. In the spectrum of PVA-chitosan-NH 4NO 3-EC complex, the doublet C dbnd O stretching in EC is observed in the vicinity 1800 and 1700. This indicates that there is some interaction between the salt and EC.

Studies on physical properties and fractography of electron beam irradiated poly(vinyl chloride)/epoxidized natural rubber blend in the presence of trimethylolpropane triacrylate

International Nuclear Information System (INIS)

Chantara Thevy Ratnam; Khairul Zaman Mohd Dahlan; Nasir, M.; Baharin, A.

2000-01-01

The effect of irradiation on the 50/50 poly(vinyl chloride)/epoxidized natural rubber blend was studied in the presence of 3 phr trimethylolpropane triacrylate (TMPTA). The blend was irradiated by using a 3.0 MeV electron beam machine at doses ranging from 20 to 200 kGy in air and room temperature. The tensile properties, resilience and gel fractions of the blends were measured. Electron beam irradiation of the blend in the presence of the TMPTA were found to cause crosslinking which in effect caused an enhancement in modulus and gel fraction together with a concomitant decline in ultimate elongation. The irradiation has resulted in a less hysteretic poly(vinyl chloride)/epoxidized natural rubber blend, with increased rebound resilience. The tensile strength of the blend reached a maximum at 60 kGy followed by a slight decrease at higher doses, implying embrittlement due to the excessive crosslinking. The scanning electron micrographs of the fracture surfaces of the irradiated blends show evidence consistent with the above contention. (Author)

Patterned cell arrays and patterned co-cultures on polydopamine-modified poly(vinyl alcohol) hydrogels

International Nuclear Information System (INIS)

Beckwith, Kai M; Sikorski, Pawel

2013-01-01

Live cell arrays are an emerging tool that expand traditional 2D in vitro cell culture, increasing experimental precision and throughput. A patterned cell system was developed by combining the cell-repellent properties of polyvinyl alcohol hydrogels with the cell adhesive properties of self-assembled films of dopamine (polydopamine). It was shown that polydopamine could be patterned onto spin-cast polyvinyl alcohol hydrogels by microcontact printing, which in turn effectively patterned the growth of several cell types (HeLa, human embryonic kidney, human umbilical vein endothelial cells (HUVEC) and prostate cancer). The cells could be patterned in geometries down to single-cell confinement, and it was demonstrated that cell patterns could be maintained for at least 3 weeks. Furthermore, polydopamine could be used to modify poly(vinyl alcohol) in situ using a cell-compatible deposition buffer (1 mg mL −1 dopamine in 25 mM tris with a physiological salt balance). The treatment switched the PVA hydrogel from cell repellent to cell adhesive. Finally, by combining microcontact printing and in situ deposition of polydopamine, patterned co-cultures of the same cell type (HeLa/HeLa) and dissimilar cell types (HeLa/HUVEC) were realized through simple chemistry and could be studied over time. The combination of polyvinyl alcohol and polydopamine was shown to be an attractive route to versatile, patterned cell culture experiments with minimal infrastructure requirements and low complexity. (paper)

Synthesis and Characterization of a Novel Ammonia Gas Sensor Based on PANI-PVA Blend Thin Films

Directory of Open Access Journals (Sweden)

D. B. DUPARE

2008-06-01

Full Text Available The polyaniline - polyvinyl alcohol blend films were synthesized by oxidative polymerization using chemical synthesis route. The polyaniline films were synthesized using optimized concentration of monomer aniline, hydrochloric acid as a dopant using ammonium peroxy-disulphate as a oxidant and insulating addative matrix polyvinyl alcohol on glass substrate for development of ammonia sensor. The formation of PANI- PVA blend films show good uniform surface morphology at 10ºc temperature, maintained at constant temperature bath. The synthesized PANI-PVA blend thin films were characterized by analyzing UV-Visible and FTIR spectra. The SEM study ensures that the thin films are uniform and porous in nature. The I-V characterization shows ohmic behaviour and also determines conductivity of the films. The response time of PANI-PVA blend thin films show that excellent behavior for 50-800 ppm and higher range of ammonia gas. This study reveals that PANI-PVA blend thin films provide a polymer matrix with very good mechanical strength, environmental stability, uniformity in surface, porous morphology and high conductivity, which are suitable for ammonia gas sensing.

Determination of gel content and SEM morphology for sago-PVA blends film

International Nuclear Information System (INIS)

Sarada Idris; Zulkafli Ghazali; Kamarudin Hashim

2006-01-01

Blends of polyvinyl alcohol and sago starch have been prepared to evaluate the potential of producing biodegradable products. Glycerol was introduced in the blends to improve the flexibility of the films as plasticizer in order more flexible film. These blends have been subjected to electron beam irradiation to evaluate and characterized radiation effect on the blends. Subsequently films were produced from this blend. The gel content of un-irradiated and irradiated films as evidence of cross linking was measured and discussed. This paper also discuss the films morphology from Scanning Electron Microscopy(SEM) observation. (Author)

Tensile and Water Absorption Properties of Biodegradable Composites Derived from Cassava Skin/ Polyvinyl Alcohol with Glycerol as Plasticizer

International Nuclear Information System (INIS)

Dayangku Intan Munthoub; Wan Aizan Wan Abdul Rahman

2011-01-01

Natural organic and abundant resources biopolymers received more attention due to their low cost, availability and degradability after usage. Cassava skin was used as natural fillers to the polyvinyl alcohol (PVA). Cassava skin/ poly vinyl alcohol blends were compounded using melt extrusion twin screw extruder and test samples were prepared using the compression method. Various ratios of cassava skin and glycerol were investigated to identify suitable composition based on the water absorption and tensile properties. The water absorption of the cassava skins/ PVA samples increased at higher composition of cassava skin due to their hydrophilic properties but decrease with glycerol content. The strength of the cassava skins/ PVA samples increased with the higher composition of cassava skin up to 70 wt % while gradually decreased with the increasing composition of glycerol. The Young modulus increased with glycerol content but decreased with fibre loading up to 70 wt %. Elongation at break decreased with fibre loading and glycerol up to 70 wt % and 30 phr, respectively. (author)

Preparation of CuS nanoparticles embedded in poly(vinyl alcohol ...

Indian Academy of Sciences (India)

WINTEC

ray diffraction (XRD) analyses and electron diffraction pattern also revealed the forming of CuS crystal structure in the PVA fibres. Keywords. CuS nanoparticles; electrospinning; poly(vinyl alcohol). 1. Introduction. In the past decade, the preparation of low-dimensional semiconductor nanostructures has become a hotspot of.

Preparation of CuS nanoparticles embedded in poly(vinyl alcohol)

Indian Academy of Sciences (India)

Poly(vinyl alcohol) (PVA)/CuS composite nanofibres were successfully prepared by electrospinning technique and gas–solid reaction. Scanning electron microscopic (SEM) images showed that the average diameter of PVA/CuS fibres was about 150–200 nm. Transmission electron microscopy (TEM) proved that a majority ...

Insulating characteristics of polyvinyl alcohol for integrated electronics

International Nuclear Information System (INIS)

Van Etten, Eliana A.; Ximenes, Eder S.; Tarasconi, Lucas T.; Garcia, Irene T.S.; Forte, Maria M.C.; Boudinov, Henri

2014-01-01

The aim of this work is to evaluate the effects of molecular weight, hydrolysis degree, and cross-link on the performance of Polyvinyl Alcohol (PVA) when applied as dielectric material in organic field effect transistors. For this purpose, metal–insulator-structures and polymeric films were characterized. The polymer structure was analyzed by thermogravimetry and calorimetry, and the electrical characterization of the films was performed through current–voltage and capacitance–voltage curves; and dielectric spectrometry. Cross-linkage, followed by hydrolysis degree, presented the major impact on polymer properties, due to the strong influence on chain mobility. The chain mobility increases the dielectric response and decreases the insulation capacity, generating the need to compromise between these two properties. The largest drawback encountered was the high sensitivity of the films to ambient humidity. The best performance of the organic insulator was obtained from cross-linked films made of an incompletely hydrolyzed PVA. - Highlights: • Effect of molecular weight, hydrolysis and cross-link on polyvinyl alcohol (PVA) dielectric • Cross-linkage, followed by hydrolysis, showed the major impact on properties. • Cross-linkage followed by hydrolysis showed the strongest effect on chain mobility. • Best dielectric performance: cross-linked films made of incompletely hydrolyzed PVA • Largest drawback is the high sensitivity of the films to ambient humidity

Degradation of polyvinyl chloride (PVC) / hydrolyzed collagen (HC) blends active sludge test.

Science.gov (United States)

Agafiţei, Gabriela-Elena; Pascu, Mihaela; Cazacu, Georgeta; Vasile, Cornelia

2008-01-01

Biodegradable polymers represent a solution for the environment protection: they decrease the landfill space, by declining the petrochemical sources, and offer also an alternative solution for the recycling. The behavior during degradation in the presence of active sludge of some polyvinyl chloride (PVC) based blends with variable content of hydrolyzed collagen (HC) has been followed. Some samples were subjected to UV irradiation, for 30 hours. The modifications induced in the environment by the polymer systems (pH variation, bacterial composition), as well as the changes of the properties of the blends (weight losses, aspect etc.) were studied. During the first moments of degradation in active sludge, all the samples absorbed water, behavior which favored the biodegradation. The bacteriological analysis of the sludge indicates the presence of some microbiological species. Generally, the populations of microorganisms decrease, excepting the sulphito-reducing anaerobic bacteria, the actinomycetes and other anaerobic bacteria. PVC/HC blends are degraded with a significant rate in active sewage sludge. More susceptible for the degradation are the UV irradiated blends. After the migration of the components with a small molecular mass in the environment, the natural polymer is degraded. The degradation effect increases with the content in the natural polymer.

Radiation preparation of graphene/carbon nanotubes hybrid fillers for mechanical reinforcement of poly(vinyl alcohol) films

Science.gov (United States)

Ma, Hui-Ling; Zhang, Long; Zhang, Youwei; Wang, Shuojue; Sun, Chao; Yu, Hongyan; Zeng, Xinmiao; Zhai, Maolin

2016-01-01

Graphene/carbon nanotubes (G/CNTs) hybrid fillers were synthesized by γ-ray radiation reduction of graphene oxide (GO) in presence of CNTs. The obtained hybrid fillers with three-dimensional (3D) interconnected network structure were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Poly(vinyl alcohol) (PVA) composite films with enhanced mechanical properties and thermal stability were subsequently prepared by solution blending of G/CNTs with PVA matrix. The tensile strength and Young's modulus of PVA composite films containing 1 wt% G/CNTs were measured to be 81.9 MPa and 3.9 GPa respectively, which were 56% and 33.6% higher than those of pure PVA. These substantial improvements could be attributed to the interconnected 3D structure of G/CNTs, homogeneous dispersion as well as the strong hydrogen-bonding interaction between G/CNTs and PVA macromolecular chains.

Effect of hygroscopic materials on water vapor permeation and dehumidification performance of poly(vinyl alcohol) membranes

KAUST Repository

Bui, T. D.

2017-01-16

In this study, two hygroscopic materials, inorganic lithium chloride (LiCl) and organic triethylene glycol (TEG) were separately added to poly(vinyl alcohol) (PVA) to form blend membranes for air dehumidification. Water vapor permeation, dehumidification performance and long-term durability of the membranes were studied systematically. Membrane hydrophilicity and water vapor sorbability increased significantly with higher the hygroscopic material contents. Water vapor permeance of the membranes increased with both added hygroscopic material and absorbed water. Water permeation energy varied from positive to negative with higher hygroscopic content. This observation is attributed to a lower diffusion energy and a relatively constant sorption energy when hygroscopic content increases. Comparatively, PVA/TEG has less corrosive problems and is more environmentally friendly than PVA/LiCl. A membrane with PVA/TEG is observed to be highly durable and is suitable for dehumidification applications.

Proton-conducting membrane based on epoxy resin-poly(vinyl alcohol)-sulfosuccinic acid blend and its nanocomposite with sulfonated multiwall carbon nanotubes for fuel-cell application

Science.gov (United States)

Kakati, Nitul; Das, Gautam; Yoon, Young Soo

2016-01-01

A blend of poly(vinyl alcohol) (PVA) with diglycidyl ether of bisphenol-A (DGB) in the presence of sulfosuccinic acid (SSA) was investigated as hydrolytically-stable proton-conducting membrane. The PVA modification was carried out by varying the DGB:SSA ratio (20:20, 10:20, and 5:20). A nanocomposite of the blend (20:20) was prepared with sulfonated multiwall carbon nanotubes (viz., 1, 3 and 5 wt%). The water uptake behavior and the proton conductivity of the prepared membranes were evaluated. The ionic conductivity of the membranes and the water uptake behavior depended on the s-MWCNT and the DGB contents. The ionic conductivity showed an enhancement for the blend and for the nanocomposite membrane as compared to the pristine polymer.

One pot synthesis of new poly(vinyl alcohol) blended natural polymer based magnetic hydrogel beads: Controlled natural anticancer alkaloid delivery system.

Science.gov (United States)

Kesavan, Mookkandi Palsamy; Ayyanaar, Srinivasan; Lenin, Nayagam; Sankarganesh, Murugesan; Dhaveethu Raja, Jeyaraj; Rajesh, Jegathalaprathaban

2018-02-01

Facile one-pot synthesis has been demonstrated for new biocompatible and dual responsive magnetic iron oxide nanoparticles cross-linked poly(vinyl alcohol) (PVA) blended natural polymer chitosan (CS) based hydrogel beads (mCS-PVA) as a controlled natural anticancer alkaloid Luotonin A (LuA) delivery system. The prepared magnetic hydrogel beads were characterized using powder X-ray diffraction measurement, Fourier transform-infrared spectroscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, and vibrating sample magnetometer. The magnetic hydrogel beads are exhibited significant water retention and follow the second order kinetic model in swelling study. The swelling ratio of the magnetic gel beads increased by the addition of PVA and showed a maximum swelling ratio of 40.83 ± 1.01 g/g and follows non-Fickian water transport mechanism. Stimuli responsive mCS and mCS-PVA hydrogel beads functionalized with LuA is demonstrated for controlled release at physiological pH and under magnetic field. The magnetic hydrogel beads show highest LuA releasing efficacy at acidic medium (pH = 5.0) with maximum efficiency of 73.33 ± 1.44%. This efficacy may also be tuned by altering the external magnetic field as well as the weight percentage (wt %) of polyethylene glycol. It is clearly that the newly produced magnetic hydrogel beads can be served as an effective intestinal LuA delivery system. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 106A: 543-551, 2018. © 2017 Wiley Periodicals, Inc.

Cellulose-glycerol-polyvinyl alcohol composite films for food packaging: Evaluation of water adsorption, mechanical properties, light-barrier properties and transparency.

Science.gov (United States)

Cazón, Patricia; Vázquez, Manuel; Velazquez, Gonzalo

2018-09-01

Nowadays consumers are aware of environmental problems. As an alternative to petrochemical polymers for food packaging, researchers have been focused on biopolymeric materials as raw material. The aim of this study was to evaluate mechanical properties (toughness, burst strength and distance to burst), water adsorption, light-barrier properties and transparency of composite films based on cellulose, glycerol and polyvinyl alcohol. Scanning electron microscopy, spectral analysis (FT-IR and UV-VIS-NIR) and differential scanning calorimetry were performed to explain the morphology, structural and thermal properties of the films. Results showed that polyvinyl alcohol enhances the toughness of films up to 44.30 MJ/m 3 . However, toughness decreases when glycerol concentration is increased (from 23.41 to 10.55 MJ/m 3 ). Water adsorption increased with increasing polyvinyl alcohol concentration up to 222%. Polyvinyl alcohol increased the film thickness. The films showed higher burst strength (up to 12014 g) than other biodegradable films. The films obtained have optimal values of transparency like those values of synthetic polymers. Glycerol produced a UV protective effect in the films, an important effect for food packaging to prevent lipid oxidative deterioration. Results showed that it is feasible to obtain cellulose-glycerol-polyvinyl alcohol composite films with improved properties. Copyright © 2018 Elsevier Ltd. All rights reserved.

Oxidation and Destruction of Polyvinyl Alcohol under the Combined Action of Ozone-Oxygen Mixture and Hydrogen Peroxide

Science.gov (United States)

Zimin, Yu. S.; Kutlugil'dina, G. G.; Mustafin, A. G.

2018-03-01

The oxidative transformations of a polyvinyl alcohol in aqueous solutions are studied under the simultaneous action of the two oxidizing agents, an ozone-oxygen mixture and a hydrogen peroxide. Effective parameters a and b, which characterize the first and second channels of carboxyl group accumulation, respectively, grow linearly upon an increase in the initial concentration of H2O2. After the temperature dependence of a and b parameters (331-363 K) in a PVA + O3 + O2 + H2O2 + H2O reaction system is studied, the parameters of the activation of COOH group accumulation are found (where PVA is a polyvinyl alcohol). New data on the effect process conditions (length of oxidation, temperature, and hydrogen peroxide concentration) have on the degree of destructive transformations of polyvinyl alcohol in the investigated reaction system are obtained.

Contribution of Charges in Polyvinyl Alcohol Networks to Marine Antifouling.

Science.gov (United States)

Yang, Wufang; Lin, Peng; Cheng, Daocang; Zhang, Longzhou; Wu, Yang; Liu, Yupeng; Pei, Xiaowei; Zhou, Feng

2017-05-31

Semi-interpenetrated polyvinyl alcohol polymer networks (SIPNs) were prepared by integrating various charged components into polyvinyl alcohol polymer. Contact angle measurement, attenuated total reflection Fourier transform infrared spectroscopy, field emission scanning electron microscopy, and tensile tests were used to characterize the physicochemical properties of the prepared SIPNs. To investigate the contribution of charges to marine antifouling, the adhesion behaviors of green algae Dunaliella tertiolecta and diatoms Navicula sp. in the laboratory and of the actual marine animals in field test were studied for biofouling assays. The results suggest that less algae accumulation densities are observed for neutral-, anionic-, and zwitterionic-component-integrated SIPNs. However, for the cationic SIPNs, despite the hydration shell induced by the ion-dipole interaction, the resistance to biofouling largely depends on the amount of cationic component because of the possible favorable electrostatic attraction between the cationic groups in SIPNs and the negatively charged algae. Considering that the preparation of novel nontoxic antifouling coating is a long-standing and cosmopolitan industrial challenge, the SIPNs may provide a useful reference for marine antifouling and some other relevant fields.

Radiation processing of indigenous natural polymers. Properties of radiation modified blends from sago-starch for biodegradable composite

International Nuclear Information System (INIS)

Ghazali, Z.; Dahlan, K.Z.; Wongsuban, B.; Idris, S.; Muhammad, K.

2001-01-01

Research and development on biodegradable polymer blends and composites have gained wider interest to offer alternative eco-friendly products. Natural polysaccharide such as sago-starch offers the most promising raw material for the production of biodegradable composites. The potential of sago, which is so abundant in Malaysia, to produce blends for subsequent applications in composite material, was evaluated and explored. Blends with various formulations of sago starch and polyvinyl alcohol (PVA), and polyvinyl pyrrolidone (PVP) polymers were prepared and subjected to radiation modification using electron beam irradiation. The effect of irradiation on the sago and its blends was evaluated and their properties were characterized. The potential of producing composite from sago blends was explored. Foams from these blends were produced using microwave oven while films were produced through casting method. The properties such as mechanical, water absorption, expansion ratio, and biodegradability were characterized and reported in this paper. (author)

Radiation processing of indigenous natural polymers. Properties of radiation modified blends from sago-starch for biodegradable composite

Energy Technology Data Exchange (ETDEWEB)

Ghazali, Z.; Dahlan, K.Z. [Malaysian Institute for Nuclear and Technology Research (MINT), Bangi, Kajang (Malaysia); Wongsuban, B.; Idris, S.; Muhammad, K. [Universiti Putra Malaysia, Faculty of Food Science and Biotechnology, Department of Food Science, Serdang (Malaysia)

2001-03-01

Research and development on biodegradable polymer blends and composites have gained wider interest to offer alternative eco-friendly products. Natural polysaccharide such as sago-starch offers the most promising raw material for the production of biodegradable composites. The potential of sago, which is so abundant in Malaysia, to produce blends for subsequent applications in composite material, was evaluated and explored. Blends with various formulations of sago starch and polyvinyl alcohol (PVA), and polyvinyl pyrrolidone (PVP) polymers were prepared and subjected to radiation modification using electron beam irradiation. The effect of irradiation on the sago and its blends was evaluated and their properties were characterized. The potential of producing composite from sago blends was explored. Foams from these blends were produced using microwave oven while films were produced through casting method. The properties such as mechanical, water absorption, expansion ratio, and biodegradability were characterized and reported in this paper. (author)

The use of filter paper plasticized with polyvinyl alcohol-glutaraldehyde in ELISA

Directory of Open Access Journals (Sweden)

G.H.T.S. Barbosa

2000-07-01

Full Text Available F1-antigen purified from Yersinia pestis was covalently linked to 5-mm diameter filter paper discs plasticized with polyvinyl alcohol-glutaraldehyde. These discs were used both for ELISA and dot-ELISA for the detection of anti-F1 IgG in rabbits. The best conditions were achieved using 1.25 µg of F1 antigen/disc, 3% w/v skim milk in PBS as blocking agent, anti-IgG peroxidase conjugate diluted 12,000 times, and serum from rabbits immunized or not against Y. pestis, diluted 6,400 times. The absorbance values obtained from the comparative study between this procedure and conventional ELISA were not significantly different but the low cost of the reagents employed in ELISA using the filter paper discs plasticized with polyvinyl alcohol-glutaraldehyde makes this method economically attractive.

Oxidative Mineralization and Characterization of Polyvinyl Alcohol Solutions for Wastewater Treatment

Energy Technology Data Exchange (ETDEWEB)

Oji, L.N.

1999-08-31

The principal objectives of this study are to identify an appropriate polyvinyl alcohol (PVA) oxidative mineralization technique, perform compatibility and evaporation fate tests for neat and mineralized PVA, and determine potential for PVA chemical interferences which may affect ion exchange utilization for radioactive wastewater processing in the nuclear industry.

Preparation and Characterization of Polyvinyl Alcohol-Chitosan Composite Films Reinforced with Cellulose Nanofiber

Science.gov (United States)

Choo, Kaiwen; Ching, Yern Chee; Chuah, Cheng Hock; Julai, Sabariah; Liou, Nai-Shang

2016-01-01

In this study microcrystalline cellulose (MCC) was oxidized by 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)-mediated oxidation. The treated cellulose slurry was mechanically homogenized to form a transparent dispersion which consisted of individual cellulose nanofibers with uniform widths of 3–4 nm. Bio-nanocomposite films were then prepared from a polyvinyl alcohol (PVA)-chitosan (CS) polymeric blend with different TEMPO-oxidized cellulose nanofiber (TOCN) contents (0, 0.5, 1.0 and 1.5 wt %) via the solution casting method. The characterizations of pure PVA/CS and PVA/CS/TOCN films were performed in terms of field emission scanning electron microscopy (FESEM), tensile tests, thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction (XRD). The results from FESEM analysis justified that low loading levels of TOCNs were dispersed uniformly and homogeneously in the PVA-CS blend matrix. The tensile strength and thermal stability of the films were increased with the increased loading levels of TOCNs to a maximum level. The thermal study indicated a slight improvement of the thermal stability upon the reinforcement of TOCNs. As evidenced by the FTIR and XRD, PVA and CS were considered miscible and compatible owing to hydrogen bonding interaction. These analyses also revealed the good dispersion of TOCNs within the PVA/CS polymer matrix. The improved properties due to the reinforcement of TOCNs can be highly beneficial in numerous applications. PMID:28773763

Comparison of polyvinyl alcohol- and formalin-preserved fecal specimens in the formalin-ether sedimentation technique for parasitological examination.

OpenAIRE

Carroll, M J; Cook, J; Turner, J A

1983-01-01

A total of 965 paired fecal specimens preserved in polyvinyl alcohol fixative and Formalin were processed by the Formalin-ether sedimentation technique. The effectiveness of the concentration procedures with material from each preservative was determined by comparing both diagnostic efficiency (percent identified) and quantitative egg and semiquantitative cyst counts. Of the 319 infections, 69.5% were detected in concentrates from both preservatives, 6.9% from polyvinyl alcohol only, and 23.5...

Synthesis of MoO 3 and its polyvinyl alcohol nanostructured film

Indian Academy of Sciences (India)

The solvent casting method is adopted for the synthesis of MoO3 dispersed polyvinyl alcohol nanostructured film (MoO3–PVA). These synthesized MoO3 and their composite samples are characterized for their structure, morphology, bonding and thermal behaviour by XRD, SEM, IR and DSC techniques, respectively.

White organic light-emitting diodes based on electroplex from polyvinyl carbazole and carbazole oligomers blends

International Nuclear Information System (INIS)

Fei-Peng, Chen; Bin, Xu; Wen-Jing, Tian; Zu-Jin, Zhao; Ping, Lü; Chan, Im

2010-01-01

White organic light-emitting diodes with a blue emitting material fluorene-centred ethylene-liked carbazole oligomer (Cz6F) doped into polyvinyl carbazole (PVK) as the single light-emitting layer are reported. The optical properties of Cz6F, PVK, and PVK:Cz6F blends are studied. Single and double layer devices are fabricated by using PVK: Cz6F blends, and the device with the configuration of indium tin oxide (ITO)/PVK:Cz6F/tris(8-hydroxyquinolinate)aluminium (Alq 3 )/LiF/A1 exhibits white light emission with Commission Internationale de l'Éclairage chromaticity coordinates of (0.30, 0.33) and a brightness of 402 cd/m 2 . The investigation reveals that the white light is composed of a blue–green emission originating from the excimer of Cz6F molecules and a red emission from an electroplex from the PVK:Cz6F blend films

White organic light-emitting diodes based on electroplex from polyvinyl carbazole and carbazole oligomers blends

Science.gov (United States)

Chen, Fei-Peng; Xu, Bin; Zhao, Zu-Jin; Tian, Wen-Jing; Lü, Ping; Im, Chan

2010-03-01

White organic light-emitting diodes with a blue emitting material fluorene-centred ethylene-liked carbazole oligomer (Cz6F) doped into polyvinyl carbazole (PVK) as the single light-emitting layer are reported. The optical properties of Cz6F, PVK, and PVK:Cz6F blends are studied. Single and double layer devices are fabricated by using PVK: Cz6F blends, and the device with the configuration of indium tin oxide (ITO)/PVK:Cz6F/tris(8-hydroxyquinolinate)aluminium (Alq3)/LiF/A1 exhibits white light emission with Commission Internationale de l'Éclairage chromaticity coordinates of (0.30, 0.33) and a brightness of 402 cd/m2. The investigation reveals that the white light is composed of a blue-green emission originating from the excimer of Cz6F molecules and a red emission from an electroplex from the PVK:Cz6F blend films.

Mechanical, relaxation behavior and thermal degradation of UV irradiated poly(vinyl acetate)/poly( methyl methacrylate) blends

International Nuclear Information System (INIS)

Mansour, S.A.; Hafez, M.; Hussien, K.A.

2005-01-01

The effect of different doses of UV- irradiation on the mechanical and relaxation properties of poly(vinyl acetate)/poly(methyl methacrylate) blends were studied. Films of PVAc/PMMA blend with different contents were prepared using the casting technique. Also, PMMA could be blended with PVAc to improve its impact strength. Moreover UV-irradiation causes degradation of PVAc and formation of ketonic and aldehyde carbonyl groups according to a suggested scheme. Irradiation of PvAc/ PMMA blends causes a higher degree of degradation as compared to the PVAc alone although the PMMA is more susceptible than PVAc to the influence of radiation. Recognizable differences are observed for all parameters between the unirradiated and irradiated samples. Existence of a relaxation mechanism within the first 200s is reported. The shear modulus for all samples is also obtained and discussed. These data are used to calculate the strain energy density using the equation proposed by Blatzetal(1974 trans. Soc.Rheol. 18 145-61), based on the n-measure of Sethe

Influence of the covalent immobilization of graphene oxide in poly(vinyl alcohol) on human osteoblast response.

Science.gov (United States)

Linares, Javier; Matesanz, María Concepción; Feito, María José; Salavagione, Horacio Javier; Martínez, Gerardo; Gómez-Fatou, Marián; Portolés, María Teresa

2016-02-01

The differences in the response of human Saos-2 osteoblasts to nanocomposites of poly(vinyl alcohol) (PVA) and 1.5wt.% graphene oxide (GO) prepared by covalent linking (PVA/GO-c) and simple blending (PVA/GO-m) have been evaluated through different biocompatibility parameters. The effects produced on osteoblasts by these two nanocomposites were analysed in parallel and compared with the direct action of GO and with the effect of PVA films without GO. The intracellular content of reactive oxygen species (ROS) and the levels of interleukin-6 (IL-6) were measured to evaluate oxidative stress induction and protective response, respectively. The results demonstrate that the combination of GO with PVA reduces both the proliferation delay and the internal cell complexity alterations induced by GO on human osteoblasts. Moreover, the covalent attachment of GO to the PVA chains increases both cell viability and IL-6 levels, reducing both apoptosis and intracellular ROS content when compared to simple blending of both materials. The use of this strategy to modulate the biointerface reduces the toxic effects of graphene while preserving the reinforcement characteristics for application in tissue engineering scaffolds, and has enormous interest for polymer/graphene biomaterials development. Copyright © 2015 Elsevier B.V. All rights reserved.

Phase relations and physicochemical properties of the ammonium paratungstate - polyvinyl alcohol - water system

International Nuclear Information System (INIS)

Ostroushko, A.A.; Mikhalev, D.S.

2003-01-01

Phase relations were studied in the ammonium paratungstate - polyvinyl alcohol - water system, isothermal cross section of the phase diagram was obtained at room temperature. Visual and microscopic observations, as well as instrumental methods were used for the detection of lines of the homogeneous polymer-salt solutions existence. Concentration ratios of density of solutions, their dynamic viscosity and refractive index were studied. Area of polymer based solutions, area of salt crystallization, heterogeneous fields with two or three phases were separated. As compared with the ammonium heptamolybdate - polyvinyl alcohol - water system the increase of solubility of components under day lighting and ultraviolet radiation escaped detection. The studied system is provided properties indicative of the formation of mesomorphic phase, photochemical reduction of ions of d-metals for the occurrence of this phase is not requirement [ru

Studi Electrochemical Impedance Spectroscopy dari Lembaran Polyvinyl Alcohol dengan Penambahan Liclo4 sebagai Bahan Elektolit Baterai Li-ion

OpenAIRE

Gunawan, Indra; Wahyudianingsih, Wahyudianingsih; Sudaryanto, Sudaryanto

2016-01-01

ELECTROCHEMICALIMPEDANCE SPECTROSCOPY STUDY OF POLYVINYL ALCOHOL SHEETWITHADDITION OFLiClO4AS ELECTROLYTE MATERIAL OF Li-ION BATTERAY. Solid polymer electrolyte materials for Li ion battery have been prepared using polyvinyl alcohol (PVA) added by lithium perchlorate (LiClO4) salt with various concentration. Electrochemical Impedance Spectroscopy (EIS) study of the material was done by making a Nyquist plot of the measurement with a LCR meter. These electrolyte materials prepared by using PVA...

Novel polyvinyl alcohol-bioglass 45S5 based composite nanofibrous membranes as bone scaffolds

International Nuclear Information System (INIS)

Shankhwar, Nisha; Kumar, Manishekhar; Mandal, Biman B.; Srinivasan, A.

2016-01-01

Composite nanofibrous membranes based on sol-gel derived 45SiO 2 24.5CaO 24.5 Na 2 O 6 P 2 O 5 (bioglass, BG) and 43SiO 2 24.5CaO 24.5 Na 2 O 6 P 2 O 5 2Fe 2 O 3 (magnetic bioglass, MBG) blended with polyvinyl alcohol (PVA) have been electrospun. These low cost membranes were mostly amorphous in structure with minor crystalline (sodium calcium phosphate) precipitates. All membranes were biodegradable. Among these, the composites exhibited higher tensile strength, better proliferation of human osteosarcoma MG63 cells and higher alkaline phosphatase enzyme activity than the bare PVA membrane, indicating their potential in bone tissue engineering. The magnetic PVA-MBG scaffold was also found to be a promising candidate for magnetic hyperthermia application. - Highlights: • Electrospun low-cost PVA-45S5 bioglass (BG) nanofibrous membranes • PVA-BG membranes containing 2 wt.% Fe 2 O 3 exhibit spontaneous magnetization. • BG fillers strongly enhanced mechanical strength and bioresponse of membranes. • Membranes show promise for bone scaffold and hyperthermia applications.

Effect of Saponification Condition on the Morphology and Diameter of the Electrospun Poly(vinyl acetate) Nanofibers for the Fabrication of Poly(vinyl alcohol) Nanofiber Mats

OpenAIRE

Seong Baek Yang; Jong Won Kim; Jeong Hyun Yeum

2016-01-01

Novel poly(vinyl alcohol) (PVA) nanofiber mats were prepared for the first time through heterogeneous saponification of electrospun poly(vinyl acetate) (PVAc) nanofibers. The effect of varying the saponification conditions, including temperature, time, and concentration of the alkaline solution, on the morphology of the saponified PVA fibers were evaluated by field-emission scanning electron microscopy. At 25 °C, the saponified PVA fibers exhibited a broad diameter distribution. The average f...

Changes induced by UV radiation in the presence of sodium benzoate in films formulated with polyvinyl alcohol and carboxymethyl cellulose

International Nuclear Information System (INIS)

Villarruel, S.; Giannuzzi, L.; Rivero, S.; Pinotti, A.

2015-01-01

This work was focused on: i) developing single and blend films based on carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVOH) studying their properties, ii) analyzing the interactions between CMC and PVOH and their modifications UV-induced in the presence of sodium benzoate (SB), and iii) evaluating the antimicrobial capacity of blend films containing SB with and without UV treatment. Once the blend films with SB were exposed to UV radiation, they exhibited lower moisture content as well as a greater elongation at break and rougher surfaces compared to those without treatment. Considering oxygen barrier properties, the low values obtained would allow their application as packaging with selective oxygen permeability. Moreover, the characteristics of the amorphous phase of the matrix prevailed with a rearrangement of the structure of the polymer chain, causing a decrease of the crystallinity degree. These results were supported by X-rays and DSC analysis. FT-IR spectra reflected some degree of polymer–polymer interaction at a molecular level in the amorphous regions. The incorporation of sodium benzoate combined with UV treatment in blend films was positive from the microbial point of view because of the growth inhibition of a wide spectrum of microorganisms. From a physicochemical perspective, the UV treatment of films also changed their morphology rendering them more insoluble in water, turning the functionalized blend films into a potential material to be applied as food packaging. - Highlights: • CMC:PVOH blend films were developed with the addition of sodium benzoate (SB). • Exposition to UV radiation was carried out with sodium benzoate as photoinitiator. • Blend films were exposed to UV radiation to modify their surface morphology. • Low O 2 permeability of UV treated blends allow them to be used as selective packaging. • Efficacy of SB as an antimicrobial agent was examined with and without UV radiation

Changes induced by UV radiation in the presence of sodium benzoate in films formulated with polyvinyl alcohol and carboxymethyl cellulose

Energy Technology Data Exchange (ETDEWEB)

Villarruel, S. [Faculty of Exact Sciences, UNLP (Argentina); Giannuzzi, L.; Rivero, S. [Center for Research and Development in Food Cryotechnology (CCT-CONICET La Plata), 47 and 116 (Argentina); Pinotti, A., E-mail: acaimpronta@hotmail.com [Center for Research and Development in Food Cryotechnology (CCT-CONICET La Plata), 47 and 116 (Argentina); Faculty of Engineering, UNLP, La Plata 1900 (Argentina)

2015-11-01

This work was focused on: i) developing single and blend films based on carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVOH) studying their properties, ii) analyzing the interactions between CMC and PVOH and their modifications UV-induced in the presence of sodium benzoate (SB), and iii) evaluating the antimicrobial capacity of blend films containing SB with and without UV treatment. Once the blend films with SB were exposed to UV radiation, they exhibited lower moisture content as well as a greater elongation at break and rougher surfaces compared to those without treatment. Considering oxygen barrier properties, the low values obtained would allow their application as packaging with selective oxygen permeability. Moreover, the characteristics of the amorphous phase of the matrix prevailed with a rearrangement of the structure of the polymer chain, causing a decrease of the crystallinity degree. These results were supported by X-rays and DSC analysis. FT-IR spectra reflected some degree of polymer–polymer interaction at a molecular level in the amorphous regions. The incorporation of sodium benzoate combined with UV treatment in blend films was positive from the microbial point of view because of the growth inhibition of a wide spectrum of microorganisms. From a physicochemical perspective, the UV treatment of films also changed their morphology rendering them more insoluble in water, turning the functionalized blend films into a potential material to be applied as food packaging. - Highlights: • CMC:PVOH blend films were developed with the addition of sodium benzoate (SB). • Exposition to UV radiation was carried out with sodium benzoate as photoinitiator. • Blend films were exposed to UV radiation to modify their surface morphology. • Low O{sub 2} permeability of UV treated blends allow them to be used as selective packaging. • Efficacy of SB as an antimicrobial agent was examined with and without UV radiation.

Hybrid composite based on poly(vinyl alcohol) and fillers from renewable resources

Science.gov (United States)

Hybrid composite laminates consisting of polyvinyl alcohol (PVA) as continuous phase (33% by weight) and lignocellulosic fillers, derived from sugarcane bagasse, apple and orange waste (22% by weight) were molded in a carver press in the presence of water and glycerol such as platicizers agents. Cor...

Effect of the polymer concentration on the ON/OFF states of a TN-LCD: polyvinyl alcohol vs. soy lecithin

Science.gov (United States)

de Coss Martinez, Romeo; Gonzalez Murguia, Jose Luis

2011-03-01

In this work we study the response of a Twisted Nematic Liquid Crystal Display (TN-LCD) by varying both the concentration and the polymer used for the microgroove. We compare the performance of two polymers: polyvinyl alcohol and soy lecithin. In particular, the light transmission for the ON/OFF states is evaluated. The polyvinyl alcohol is a polymer widely used in LCDs while lecithin soy is a natural polymer.

Poly(vinyl alcohol) cryogel phantoms for use in ultrasound and MR imaging

International Nuclear Information System (INIS)

Surry, K J M; Austin, H J B; Fenster, A; Peters, T M

2004-01-01

Poly(vinyl alcohol) cryogel, PVA-C, is presented as a tissue-mimicking material, suitable for application in magnetic resonance (MR) imaging and ultrasound imaging. A 10% by weight poly(vinyl alcohol) in water solution was used to form PVA-C, which is solidified through a freeze-thaw process. The number of freeze-thaw cycles affects the properties of the material. The ultrasound and MR imaging characteristics were investigated using cylindrical samples of PVA-C. The speed of sound was found to range from 1520 to 1540 m s -1 , and the attenuation coefficients were in the range of 0.075-0.28 dB (cm MHz) -1 . T1 and T2 relaxation values were found to be 718-1034 ms and 108-175 ms, respectively. We also present applications of this material in an anthropomorphic brain phantom, a multi-volume stenosed vessel phantom and breast biopsy phantoms. Some suggestions are made for how best to handle this material in the phantom design and development process

Film dosimeters based on methylene blue and methyl orange in polyvinyl alcohol

DEFF Research Database (Denmark)

Chung, W.H.; Miller, A.

1994-01-01

Polyvinyl alcohol (PVA) films containing methylene blue and methyl orange are useful as gamma and electron radiation dosimeters. Absorbed doses should not exceed 40 kGy for methylene blue and 500 kGy for methyl orange. Because PVA is water-soluble, the films may be made without toxic solvents...

Histochemical demonstration of creatine kinase activity using polyvinyl alcohol and auxiliary enzymes

NARCIS (Netherlands)

Frederiks, W. M.; Marx, F.; van Noorden, C. J.

1987-01-01

Creatine kinase activity (EC 2.7.3.2.) has been demonstrated in myocardium and skeletal muscle from rats by a method based on the incubation of cryostat sections with a polyvinyl alcohol-containing medium and the use of auxiliary enzymes. Hexokinase and glucose-6-phosphate dehydrogenase were spread

Compatibility of Polyvinyl Alcohol with the 241-F/H Tank Farm Liquid Waste

International Nuclear Information System (INIS)

Oji, L.N.

1998-01-01

This report describes results from laboratory-scale oxidative mineralization of polyvinyl alcohol (PVA), and the evaluation of the F/H Tank Farms as a storage/disposal option for PVA waste solution generated in the Canyons and B-line decontamination operations

Compatibility of Polyvinyl Alcohol with the 241-F/H Tank Farm Liquid Waste

Energy Technology Data Exchange (ETDEWEB)

Oji, L.N.

1998-11-25

This report describes results from laboratory-scale oxidative mineralization of polyvinyl alcohol (PVA), and the evaluation of the F/H Tank Farms as a storage/disposal option for PVA waste solution generated in the Canyons and B-line decontamination operations.

The use of positron annihilation to study polyacrylamide and polymethylmethacrylate-Alcohols and diols mixture

International Nuclear Information System (INIS)

Mostafa, N.

2007-01-01

The effect of addition of both alcohols and diols to polyacrylamide (PAA) and polymethylmethacrylate (PMMA) forming polymer mixtures was studied using positron annihilation lifetime (PAL) and Doppler broadening of annihilation radiation (DBAR) techniques. It was found that, by increasing chain length of alcohols, PAA-alcohols contain free volume with small size V and low fraction f, while PMMA-alcohols contain free volume with large size and high fraction. On the other hand, S-parameter increases and W-parameter decreases in PAA-diols according to the number of carbon and hydrogen atoms in the chain. In addition, the electrical conductivity measurements are performed on the above two polymer mixtures. The results showed that both PAA and PMMA exhibit semiconducting properties by the addition of alcohols and diols. Correlation between the macroscopic conductivity properties and the microstructures such as free volume and microdefects are established

Elution behavior of poly(ethylene glycol) through poly(vinyl alcohol) gel column using several solvents as eluents

International Nuclear Information System (INIS)

Hirayama, Chuichi; Motozato, Yoshiaki; Matsumoto, Kazuaki.

1983-01-01

γ-Irradiated poly(vinyl alcohol) beads, which were sufficiently allowed to swell in water, were washed with methanol, and then were packed into column. Gel chromatography was performed using methanol, benzene, esters and ketones as eluents and poly(ethylene glycol) as a sample. When the elution was carried out using methanol and benzene as eluents, elution behavior of samples was ordinary. When ethyl formate, methyl acetate and ethyl propionate were used as eluents, samples were slightly adsorbed and the elution was delayed. In the case the elution was carried out using ethyl acetate, propyl acetate, butyl acetate and ethyl methyl ketone as eluents, samples were adsorbed strongly on the bed material, and the adsorption curve was analogous to the calibration curve using methanol as an eluent. Dried poly(vinyl alcohol) gel as a packing material, showed ordinary elution behaviors for the samples. The adsorption of poly(ethylene glycol) on the present bed material was attributed to the existence of hydrated water on poly(vinyl alcohol) gel matrix. (author)

Performance and diversity of polyvinyl alcohol-degrading bacteria under aerobic and anaerobic conditions.

Science.gov (United States)

Huang, Jianping; Yang, Shisu; Zhang, Siqi

2016-11-01

To compare the degradation performance and biodiversity of a polyvinyl alcohol-degrading microbial community under aerobic and anaerobic conditions. An anaerobic-aerobic bioreactor was operated to degrade polyvinyl alcohol (PVA) in simulated wastewater. The degradation performance of the bioreactor during sludge cultivation and the microbial communities in each reactor were compared. Both anaerobic and aerobic bioreactors demonstrated high chemical oxygen demand removal efficiencies of 87.5 and 83.6 %, respectively. Results of 16S rDNA sequencing indicated that Proteobacteria dominated in both reactors and that the microbial community structures varied significantly under different operating conditions. Both reactors obviously differed in bacterial diversity from the phyla Planctomycetes, Chlamydiae, Bacteroidetes, and Chloroflexi. Betaproteobacteria and Alphaproteobacteria dominated, respectively, in the anaerobic and aerobic reactors. The anaerobic-aerobic system is suitable for PVA wastewater treatment, and the microbial genetic analysis may serve as a reference for PVA biodegradation.

Electrospinning of poly(vinyl alcohol) nanofibers loaded with hexadecane nanodroplets.

Science.gov (United States)

Arecchi, A; Mannino, S; Weiss, J

2010-08-01

The feasibility of producing poly(vinyl alcohol) (PVA) nanofibers containing fine-disperse hexadecane droplets by electrospinning a blend of hexadecane-in-water emulsions and PVA was investigated. Hexadecane oil-in-water nanoemulsions (d(10)= 181.2 +/- 0.1 nm) were mixed with PVA at pH 4.5 to yield polymer-emulsion blends containing 0.5 to 1.5 wt% oil droplets and 8-wt% PVA. The solution properties of emulsions and emulsion-PVA blends (viscosity, conductivity, surface tension) were determined. Solutions were electrospun and the morphology and thermal properties of deposited fiber mats characterized by scanning electron microscopy and differential scanning calorimetry. Fiber mats were dissolved in buffer to liberate incorporated hexadecane droplets and the buffer solutions analyzed by optical microscopy, UV-spectroscopy, and light scattering. Analysis of dry fiber mats and their solutions showed that emulsion droplets were indeed part of the electrospun fiber structures. Depending on the concentration of hexadecane in the initial emulsion-polymer blends, droplets were dispersed in the fibers as individual droplets or in form of aggregated flocs of hexadecane droplets. Nanofibers with spindle-like perturbations or nanofibers containing bead-like structures with approximately 5 times larger than the size of droplets in the original nanoemulsion were obtained. Remarkably, incorporation of hexadecane droplets in fibers did not alter size of individual droplets, that is, no coalescence occurred. The manufacture of solid matrix containing nanodroplets could be of substantial interest for manufacturers wishing to develop encapsulation system for lipophilic functional compounds such as lipid-soluble flavors, antimicrobials, antioxidants, and bioactives with tailored release kinetics. Practical Applications: The paper describes the formation of electrospun nanofibers from hydrophilic polymers that contain fine-disperse emulsion droplets. By incorporating emulsion droplets, a

78 FR 20890 - Polyvinyl Alcohol From Taiwan: Preliminary Results of Antidumping Duty Administrative Review...

Science.gov (United States)

2013-04-08

... DEPARTMENT OF COMMERCE International Trade Administration [A-583-841] Polyvinyl Alcohol From... Administration, International Trade Administration, Department of Commerce. SUMMARY: The Department of Commerce..., AD/CVD Operations, Office 1, Import Administration, International Trade Administration, U.S...

Properties and Applications of Polyvinyl Alcohol, Halloysite Nanotubes and Their Nanocomposites.

Science.gov (United States)

Gaaz, Tayser Sumer; Sulong, Abu Bakar; Akhtar, Majid Niaz; Kadhum, Abdul Amir H; Mohamad, Abu Bakar; Al-Amiery, Ahmed A

2015-12-19

The aim of this review was to analyze/investigate the synthesis, properties, and applications of polyvinyl alcohol-halloysite nanotubes (PVA-HNT), and their nanocomposites. Different polymers with versatile properties are attractive because of their introduction and potential uses in many fields. Synthetic polymers, such as PVA, natural polymers like alginate, starch, chitosan, or any material with these components have prominent status as important and degradable materials with biocompatibility properties. These materials have been developed in the 1980s and are remarkable because of their recyclability and consideration of the natural continuation of their physical and chemical properties. The fabrication of PVA-HNT nanocomposites can be a potential way to address some of PVA's limitations. Such nanocomposites have excellent mechanical properties and thermal stability. PVA-HNT nanocomposites have been reported earlier, but without proper HNT individualization and PVA modifications. The properties of PVA-HNT for medicinal and biomedical use are attracting an increasing amount of attention for medical applications, such as wound dressings, drug delivery, targeted-tissue transportation systems, and soft biomaterial implants. The demand for alternative polymeric medical devices has also increased substantially around the world. This paper reviews individualized HNT addition along with crosslinking of PVA for various biomedical applications that have been previously reported in literature, thereby showing the attainability, modification of characteristics, and goals underlying the blending process with PVA.

Embolization therapy of uterine fibroids by using pingyangmycin lipiodol emulsion or polyvinyl alcohol particles: a clinical comparative study

International Nuclear Information System (INIS)

Zhang Dazhong; Yin Jianlin; Liu Hairi; Zhang Fuqiang; Huang Hai; Gu Youmei

2010-01-01

Objective: To evaluate the efficacy and safety of embolization of uterine fibroids by using pingyangmycin lipiodol emulsion or polyvinyl alcohol particles as embolismic materials. Methods: Seventy-three patients with uterine fibroids were divided into two groups. Patients in group A (29 cases) were treated with pingyangmycin lipiodol emulsion as embolismic materials, while patients in group B (44 cases) with polyvinyl alcohol particles (with a diameter of 300-700 μm) as embolismic materials. Embolization therapy of uterine fibroids was performed in all patients. The uterus volume, the size of uterine fibroid and sex hormone level both before and after the treatment were estimated and the results were compared between two groups. The occurrence of complications was observed. Results: The technical success of catheterization and embolization was 100% in both groups. After the therapy,both the uterus volume and the uterine fibroid size decreased significantly, but no significant difference in the size reduction existed between the two groups (P>0.05). The clinical symptoms showed a marked improvement in all patients, while the sex hormone level showed no obvious changes. No serious complications occurred. Conclusion: In treating uterine fibroids with embolization technique, both pingyangmycin lipiodol emulsion and polyvinyl alcohol particles are safe and effective embolismic materials. However, use of polyvinyl alcohol particles may be safer than pingyangmycin, as pingyangmycin is a kind of chemotherapeutic drugs, which might potentially cause some short-term or long-term complications. (authors)

Effect of irradiation on poly(vinyl chloride)/epoxidized natural rubber blend in the presence of additives: FTIR analysis

International Nuclear Information System (INIS)

Chantara Thevy Ratnam; Khairul Zaman Dahlan; Baharin, A.; Nasir, M.

2001-01-01

The effect of irradiation on the structure of 50/50 poly(vinyl chloride)/epoxidized natural rubber blend (PVC/ENR) was studied using the Fourier Transform Spectroscopy (FTIR). The 50/50 PVC/ENR blend was irradiated by using 3.0 MeV electron beam machine at 0 and 200 kGy irradiation doses. The influence of several additives such as TMPTA, Irganox 1010, and tribasic lead sulfate on the irradiation induced changes of the blend was investigated. It was found that upon irradiation, ring opening of the epoxide groups, oxidation as well crosslinking at residual double bonds occurred, leading to decreases in the intensities of the epoxide and cis double bond bands and an increases in ether and furan bands. The addition of Irganox 1010 and tribasic lead sulfate were found to inhibit the irradiation-induced reaction in the blend to a considerable extent. The importance of TMPTA in preventing the intramolecular ring opening side chain reaction was also discussed. However, studies did not reveal the exact nature of the irradiation-induced reactions involved in the blend. (Author)

Novel polyvinyl alcohol-bioglass 45S5 based composite nanofibrous membranes as bone scaffolds

Energy Technology Data Exchange (ETDEWEB)

Shankhwar, Nisha [Department of Physics, Indian Institute of Technology Guwahati, Guwahati 781039 (India); Kumar, Manishekhar; Mandal, Biman B. [Department of Biosciences and Bioengineering, Indian Institute of Technology Guwahati, Guwahati 781039 (India); Srinivasan, A., E-mail: asrini@iitg.ernet.in [Department of Physics, Indian Institute of Technology Guwahati, Guwahati 781039 (India)

2016-12-01

Composite nanofibrous membranes based on sol-gel derived 45SiO{sub 2} 24.5CaO 24.5 Na{sub 2}O 6 P{sub 2}O{sub 5} (bioglass, BG) and 43SiO{sub 2} 24.5CaO 24.5 Na{sub 2}O 6 P{sub 2}O{sub 5} 2Fe{sub 2}O{sub 3} (magnetic bioglass, MBG) blended with polyvinyl alcohol (PVA) have been electrospun. These low cost membranes were mostly amorphous in structure with minor crystalline (sodium calcium phosphate) precipitates. All membranes were biodegradable. Among these, the composites exhibited higher tensile strength, better proliferation of human osteosarcoma MG63 cells and higher alkaline phosphatase enzyme activity than the bare PVA membrane, indicating their potential in bone tissue engineering. The magnetic PVA-MBG scaffold was also found to be a promising candidate for magnetic hyperthermia application. - Highlights: • Electrospun low-cost PVA-45S5 bioglass (BG) nanofibrous membranes • PVA-BG membranes containing 2 wt.% Fe{sub 2}O{sub 3} exhibit spontaneous magnetization. • BG fillers strongly enhanced mechanical strength and bioresponse of membranes. • Membranes show promise for bone scaffold and hyperthermia applications.

Preparation and Properties of the Chitosan/PVA Blend for Heavy Metals Chelation

Directory of Open Access Journals (Sweden)

Zuhair Jabbar Abdul Ameer

2016-09-01

Full Text Available Current research based on the use of extracted chitosan mixed with Polyvinyl alcohol to manufacture blend that can been used in water purification from heavy metals such as copper, this due to chitosan properties and its ability to chelation these metals because of the presence of the functional groups in their structure. The blend has been treated with borax to increase the viscosity, and then high density polyethylene granulated coated with polymer solution to increase the surface area for chelation. The ultraviolet test showed the efficiency of blend to chelation of copper ions through lower the copper ions absorbance peak after each stage where the solution of copper ions pass on the polymer blend containing chitosan.

Reverse indentation size effects in gamma irradiated blood compatible blend films of chitosan-poly (vinyl alcohol) for possible medical applications

Energy Technology Data Exchange (ETDEWEB)

Bisen, D.S. [Department of Post Graduate Studies and Research in Physics, Rani Durgawati University, Jabalpur, M.P. 482002 (India); Bhatt, Rinkesh [Department of Physics, Global Engineering College, Jabalpur, M.P. 482001 (India); Bajpai, A.K., E-mail: akbmrl@yahoo.co.in [Department of Chemistry, Bose Memorial Research Lab., Govt. Auto. Model Science College, Jabalpur 482002, M.P. (India); Bajpai, R. [Department of Post Graduate Studies and Research in Physics, Rani Durgawati University, Jabalpur, M.P. 482002 (India); Katare, R. [Department of Physics, Government Model Science College, Jabalpur, M.P. 482001 (India)

2017-02-01

In the present work binary blends of polyvinyl alcohol (PVA) and chitosan (CS) were prepared by solution cast method and characterized by analytical methods like FTIR, XRD and SEM for seeking structural and morphological information. The blends were exposed to gamma radiation and evaluated for their improved mechanical strength. It was found that the tensile strength and microhardness increased after irradiation of CS-PVA films. Plastic effect due to absorption of water molecules and scissoring effect due to gamma irradiation were found to decrease the softness or increase the microhardness of the blends. Improved mechanical properties were attributed to intermolecular and intramolecular hydrogen bonds and adhesive nature of the blends also. The blends were also investigated for water intake behavior and in vitro blood compatibility property on the basis of certain in vitro tests like protein adsorption, haemolysis and blood clot formation on the un-irradiated and irradiated blend samples. The increased % swelling with time could be assigned to the fact that increasing water content facilitates the phase separation process within the blend which results in advancement in interstitial nano-void spaces which are occupied by water molecules. The blood compatibility results showed that when the amount of CS was varied from 0.5% to 2%, the amount of blood clot and percent haemolysis decreased while the protein adsorption increased with increasing CS content of the blend films. - Highlights: • Fully crosslinked blends of PVA and chitosan have been prepared. • Blends were irradiated with gamma radiations to enhance blood compatibility. • Mechanical properties were evaluated and effect of irradiation was examined. • The blood compatibility of blends was also determined.

Reverse indentation size effects in gamma irradiated blood compatible blend films of chitosan-poly (vinyl alcohol) for possible medical applications

International Nuclear Information System (INIS)

Bisen, D.S.; Bhatt, Rinkesh; Bajpai, A.K.; Bajpai, R.; Katare, R.

2017-01-01

In the present work binary blends of polyvinyl alcohol (PVA) and chitosan (CS) were prepared by solution cast method and characterized by analytical methods like FTIR, XRD and SEM for seeking structural and morphological information. The blends were exposed to gamma radiation and evaluated for their improved mechanical strength. It was found that the tensile strength and microhardness increased after irradiation of CS-PVA films. Plastic effect due to absorption of water molecules and scissoring effect due to gamma irradiation were found to decrease the softness or increase the microhardness of the blends. Improved mechanical properties were attributed to intermolecular and intramolecular hydrogen bonds and adhesive nature of the blends also. The blends were also investigated for water intake behavior and in vitro blood compatibility property on the basis of certain in vitro tests like protein adsorption, haemolysis and blood clot formation on the un-irradiated and irradiated blend samples. The increased % swelling with time could be assigned to the fact that increasing water content facilitates the phase separation process within the blend which results in advancement in interstitial nano-void spaces which are occupied by water molecules. The blood compatibility results showed that when the amount of CS was varied from 0.5% to 2%, the amount of blood clot and percent haemolysis decreased while the protein adsorption increased with increasing CS content of the blend films. - Highlights: • Fully crosslinked blends of PVA and chitosan have been prepared. • Blends were irradiated with gamma radiations to enhance blood compatibility. • Mechanical properties were evaluated and effect of irradiation was examined. • The blood compatibility of blends was also determined.

Reentrant behaviour in polyvinyl alcohol-borax hydrogels

Science.gov (United States)

Lawrence, Mathias B.; Desa, J. A. E.; Aswal, V. K.

2018-01-01

Polyvinyl alcohol (PVA) hydrogels, cross-linked with varying concentrations of borax, were studied with small angle neutron scattering (SANS), x-ray diffraction (XRD) and differential thermal analysis (DTA). The SANS data satisfy the Ornstein-Zernike approximation. The hydrogels are modelled as PVA chains bound by borate cross-links. Water occupies the spaces within the three-dimensional hydrogel network. The mesh size ξ indicates reentrant behaviour i.e. at first, ξ increases and later decreases as a function of borax concentration. The behaviour is explained on the basis of the balance between the charged di-diol cross-links and the shielding by free ions in the solvent. XRD and DTA show the molecular size of water in the solvent and the glass transition temperature commensurate with reentrant behaviour.

Three methods for in situ cross-linking of polyvinyl alcohol films for application as ion-conducting membranes in potassium hydroxide electrolyte. [battery separators

Science.gov (United States)

Philipp, W. H.; Hsu, L. C.

1979-01-01

Three methods of in situ cross-linking polyvinyl alcohol films are presented. They are: (1) acetalization with a dialdehyde such as glutaraldehyde, (2) acetalization with aldehyde groups formed by selective oxidative cleaving of the few percent of 1,2 diol units present in polyvinyl alcohol, and (3) cross-linking by hydrogen abstraction by reaction with hydrogen atoms and hydroxyl radicals from irradiated water. For the third method, improvement in film conductivity in KOH solution at the expense of mechanical strength is obtained by the presence of polyacrylic acid in the polyvinyl alcohol films. Resistivities in 45 percent KOH are given for in situ cross-linked films prepared by each of the three methods.

Novel ionically crosslinked acrylamide-grafted poly(vinyl alcohol)/sodium alginate/sodium carboxymethyl cellulose pH-sensitive microspheres for delivery of Alzheimer's drug donepezil hydrochloride: Preparation and optimization of release conditions.

Science.gov (United States)

Bulut, Emine; Şanlı, Oya

2016-01-01

In this work, the graft copolymer, poly(vinyl alcohol)-grafted polyacrylamide (PVA-g-PAAm), was synthesized and characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, and elemental analysis. Microspheres of PVA-g-PAAm/sodium alginate (NaAlg)/sodium carboxymethyl cellulose (NaCMC) were prepared by the emulsion-crosslinking method and used for the delivery of an Alzheimer's drug, donepezil hydrochloride (DP). The release of DP increased with the increase in drug/polymer ratio (d/p) and PVA-g-PAAm/NaAlg/NaCMC ratio, while it decreased with the increase in the extent of crosslinking. The optimum DP release was obtained as 92.9% for a PVA-g-PAAm/NaAlg/NaCMC ratio of 1/2/1, d/p ratio of 1/8, and FeCl3 concentration of 7% (w/v).

Effect of Alcohol on Diesel Engine Combustion Operating with Biodiesel-Diesel Blend at Idling Conditions

Science.gov (United States)

Mahmudul, H. M.; Hagos, Ftwi. Y.; A, M. Mukhtar N.; Mamat, Rizalman; Abdullah, A. Adam

2018-03-01

Biodiesel is a promising alternative fuel to run the automotive engine. However, its blends have not been properly investigated during idling as it is the main problem to run the vehicles in a big city. The purpose of this study is to evaluate the impact of alcohol additives such as butanol and ethanol on combustion parameters under idling conditions when a single cylinder diesel engine operates with diesel, diesel-biodiesel blends, and diesel biodiesel-alcohol blends. The engine combustion parameters such as peak pressure, heat release rate and ignition delay were computed. This investigation has revealed that alcohol blends with diesel and biodiesel, BU20 blend yield higher maximum peak cylinder pressure than diesel. B5 blend was found with the lowest energy release among all. B20 was slightly lower than diesel. BU20 blend was seen with the highest peak energy release where E20 blend was found advance than diesel. Among all, the blends alcohol component revealed shorter ignition delay. B5 and B20 blends were influenced by biodiesel interference and the burning fraction were found slightly slower than conventional diesel where BU20 and E20 blends was found slightly faster than diesel So, based on the result, it can be said that among the alcohol blends butanol and ethanol can be promising alternative at idling conditions and can be used without any engine modifications.

Biaxial stress-strain behavior of chemical and physical gels of poly(vinyl alcohol)

Czech Academy of Sciences Publication Activity Database

Meissner, Bohumil; Matějka, Libor

2008-01-01

Roč. 49, č. 10 (2008), s. 2560-2567 ISSN 0032-3861 R&D Projects: GA AV ČR IAA400500701 Institutional research plan: CEZ:AV0Z40500505 Keywords : poly(vinyl alcohol) gels * pure shear behavior * constitutive equation Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.331, year: 2008

Templated diamond growth on porous carbon foam decorated with polyvinyl alcohol-nanodiamond composite

Czech Academy of Sciences Publication Activity Database

Varga, Marián; Stehlík, Štěpán; Kaman, Ondřej; Ižák, Tibor; Domonkos, Mária; Lee, D.S.; Kromka, Alexander

2017-01-01

Roč. 119, Aug (2017), s. 124-132 ISSN 0008-6223 R&D Projects: GA ČR GC15-22102J Institutional support: RVO:68378271 Keywords : nucleation * polyvinyl alcohol * nanodiamonds * carbon foam Subject RIV: JJ - Other Materials OBOR OECD: Nano-materials (production and properties) Impact factor: 6.337, year: 2016

Microstructural and electrical properties of PVA/PVP polymer blend films doped with cupric sulphate

Energy Technology Data Exchange (ETDEWEB)

Hemalatha, K.; Gowtham, G. K.; Somashekarappa, H., E-mail: drhssappa@gmail.com [Department of Physics, Yuvaraja’s College, University of Mysore, Mysore 570 005, Karnataka (India); Mahadevaiah,; Urs, G. Thejas; Somashekar, R. [Department of Studies in Material Sciences, University of Mysore, Mysore 570 006, Karnataka (India)

2016-05-23

A series of polyvinyl alcohol (PVA)/polyvinyl pyrrolidone (PVP) polymer blends added with different concentrations of cupric sulphate (CuSO{sub 4}) were prepared by solution casting method and were subjected to X-ray diffraction (XRD) and Ac conductance measurements. An attempt has been made to study the changes in crystal imperfection parameters in PVA/PVP blend films with the increase in concentration of CuSO{sub 4}. Results show that decrease in micro crystalline parameter values is accompanied with increase in the amorphous content in the film which is the reason for film to have more flexibility, biodegradability and good ionic conductivity. AC conductance measurements in these films show that the conductivity increases as the concentration of CuSO{sub 4} increases. These films were suitable for electro chemical applications.

Physically crosslinked poly(vinyl alcohol-hydroxyethyl starch blend hydrogel membranes: Synthesis and characterization for biomedical applications

Directory of Open Access Journals (Sweden)

El-Refaie Kenawy

2014-07-01

Full Text Available Poly(vinyl alcohol, PVA is a polymer of great importance because of its many appealing characteristics specifically for various pharmaceutical and biomedical applications. Physically crosslinked hydrogel membranes composed of different amounts of hydroxyethyl starch (HES in (PVA and ampicillin were prepared by applying freeze–thawing method. This freezing–thawing cycle was repeated for three consecutive cycles. Physicochemical properties of PVA–HES membrane gel such as gel fraction, swelling, morphology, elongation, tensile strength, and protein adsorption were investigated. Introducing HES into freeze–thawed PVA structure affected crystal size distribution of PVA; and hence physicochemical properties and morphological structure have been affected. Increased HES concentration decreased the gel fraction %, maximum strength and break elongation. Indeed it resulted into a significant incrementing of the swelling ability, amount of protein adsorption, broader pore size, and pore distribution of membrane morphological structure. Furthermore, an increase in HES concentration resulted in better and still lower thermal stability compared to virgin PVA and freeze–thawed PVA. The maximum weight loss of PVA–HES hydrogel membranes ranged between 18% and 60% according to HES content, after two days of degradation in phosphate buffer saline (PBS, which indicates they are biodegradable. Thus, PVA–HES hydrogel membranes containing ampicillin could be a novel approach for biomedical application e.g. wound dressing purposes.

Polyvinyl Alcohol-Lead Nitrate Paint for Gamma Radiation Installations

International Nuclear Information System (INIS)

EI-Ahdal, M.A.

2007-01-01

Dealing with gamma ray installations represents an important problem for radiation protection workers. Radiation shielding is used to avoid the risk resulting from these gamma sources. This study suggested the use of polyvinyl alcohol (PVA) solution that contains lend nitrate (with lead metal/PVA= 1.72) to lower the gamma radiation intensity and reduce its risk to workers. This can be achieved by painting the radiation shielding with this solution Temperature relief of the irradiated solution shows the degradation of the polymer content up to 50 degree C, which starts to crosslink increasing the protection capability of this solution

In-situ reduced graphene oxide-polyvinyl alcohol composite coatings as protective layers on magnesium substrates

Directory of Open Access Journals (Sweden)

Xingkai Zhang

2017-06-01

Full Text Available A simple and feasible method was developed to fabricate in-situ reduced graphene oxide-polyvinyl alcohol composite (GO-PVA coatings as protective layers on magnesium substrates. Polyvinyl alcohol was used as an in-situ reductant to transform GO into reduced GO. Contiguous and uniform GO-PVA coatings were prepared on magnesium substrates by dip-coating method, and were further thermally treated at 120 °C under ambient condition to obtain in-situ reduced GO-PVA coatings. Owing to the reducing effect of PVA, thermal treatment at low temperature led to effective in-situ reduction of GO as confirmed by XRD, Raman, FTIR and XPS tests. The corrosion current density of magnesium substrates in 3.5 wt% NaCl solution could be lowered to its 1/25 when using in-situ reduced GO-PVA coatings as protective layers.

Effects of γ-rays on electrical conductivity of polyvinyl alcohol-polypyrrole composite polymer films

International Nuclear Information System (INIS)

Mohd Hamzah Harun; Elias Saion; Noorhana Yahya; Anuar Kassim; Ekramul Mahmud; Muhammad Yousuf Hussain; Iskandar Shahrim Mustafa; Azian Othman; Norazimah Mohd Yusof; Mohd Ahmad Ali Omer

2007-01-01

The composite polymer films of polyvinyl alcohol/polypyrrole/chloral hydrate (PVA-PPy-CH) had been prepared. Effects of γ-rays on the electrical conductivity of the composite polymer films had been investigated by using Inductance Resistance meter (LCR) meter at a frequency ranging from 20 Hz to 1 MHz. With the incorporation of choloral hydrate in the polymer sample, the conductivity increased indicates that it is capable to be used as dopant for polymerizing conjugated polymer. The electrical conductivity obtained increased as the dose increased, which is in the order of 10 -5 Scm -1 indicates that γ-ray is capable to enhance the electrical conductivity of the composite polymer films. The parameter of s is in the range of 0.31 ≤ S ≤ 0.49 and obeyed simple power law dispersion ω S . The Scanning Electron Microscopy (SEM) micrographs reveal the formation of polypyrrole globules in polyvinyl alcohol matrix which increased as the irradiation dose was increased. (Author)

Studies of PVC/ENR blends: blend compositions

International Nuclear Information System (INIS)

Chantara Thevy Ratnam; Khairul Zaman Mohd Dahlan; Nasir, M.; Baharin, A.

2002-01-01

Blends of poly(vinyl chloride/epoxidized natural rubber (PVC/ENR) were prepared by using Bra bender Plasticorder at compositions ranging from 0-100% PVC. They were blended at 150 degree C mixing temperature, 50 rpm rotor speed and 10 minutes mixing time. The blends were characterized for tensile strength , elongation at break, glass transition temperatures and Fourier transform infra red spectroscopy (FTIR). Results revealed that as the PVC content increases the blend behaviour changes from elastomeric to glassy. However the blends found to be compatible at all compositions. (Author)

The Effects of Surface Mechanical Deformation and Bovine Serum Albumin on the Tribological Properties of Polyvinyl Alcohol Hydrogel as an Artificial Cartilage

Directory of Open Access Journals (Sweden)

Feng Li

2017-01-01

Full Text Available The mechanical and tribological properties of polyvinyl alcohol hydrogel as an artificial cartilage were studied under water and bovine serum albumin-lubricated sliding conditions. The frictional properties of the polyvinyl alcohol hydrogel were investigated via reciprocating frictional tests. The effect of surface mechanical deformation on the tribological properties of the polyvinyl alcohol hydrogel as an artificial cartilage was studied by concurrently recording the z-axis displacement and friction coefficient time. Three different factors were chosen including load, speed, and lubrication. The results showed that the albumin solution could reverse the trend in the coefficient of friction in tests at different loading levels. There was no improvement in the friction condition in albumin at low speeds. However, when the speed was increased to 2 Hz, the coefficient of friction was significantly reduced. Wear testing was also conducted, and wear tracks were found on the sample surface. The results also showed that even though the surface deformation could recover as the water phase of the porous structure recovered, the coefficient of friction continued to increase simultaneously. This relationship between mechanical and frictional tests indicated that biphasic lubrication effects may not be the only dominant factor underlying the excellent friction properties of polyvinyl alcohol hydrogel.

The influence of stretching on tensile strength and solubility of poly(vinyl alcohol) fibres

NARCIS (Netherlands)

Heikens, D.; Bleijenberg, A.C.A.M.; Hoppenbrouwers, J.J.M.; Barentsen, W.M.

1971-01-01

The strength of wet-spun poly(vinyl alcohol) (pva) fibres is given as function of bath-stretching, wet-stretching and hot-stretching. In the two equations derived for strength of wet-stretching and hot-stretching the complex influence of the bath-stretching and hot-stretching is demonstrated. The

PVA/Polysaccharides Blended Films: Mechanical Properties

OpenAIRE

Silva, Fábio E. F.; Di-Medeiros, Maria Carolina B.; Batista, Karla A.; Fernandes, Kátia F.

2013-01-01

Blends of polyvinyl alcohol (PVA) and angico gum (AG) and/or cashew gum (CG) were used to produce films by casting method. Morphological and mechanical properties of these films were studied and compared to the properties of a commercial collagen membrane of bovine origin (MBO). The films presented thickness varying from 70 to 140 μm (PVA/AG) and 140 to 200 μm (PVA/CG). Macroscopic analysis showed that a PVA/CG film was very similar to MBO regarding the color and transparency. The higher valu...

Memristive learning and memory functions in polyvinyl alcohol polymer memristors

Directory of Open Access Journals (Sweden)

Yan Lei

2014-07-01

Full Text Available Polymer based memristive devices can offer simplicity in fabrication and at the same time promise functionalities for artificial neural applications. In this work, inherent learning and memory functions have been achieved in polymer memristive devices employing Polyvinyl Alcohol. The change in conduction in such polymer devices strongly depends on the pulse amplitude, duration and time interval. Through repetitive stimuli training, temporary short-term memory can transfer into consolidated long-term memory. These behaviors bear remarkable similarities to certain learning and memory functions of biological systems.

Effect of Hydroxyl Concentration on Chemical Sensitivity of Polyvinyl Alcohol/Carbon-Black Composite Chemiresistors

International Nuclear Information System (INIS)

Hughes, Robert C.; Patel, Sanjay V.; Yelton, W. Graham

1999-01-01

The sensitivity and selectivity of polyvinyl alcohol (PVA) / carbon black composite films have been found to vary depending upon the hydroxylation percentage (''-OH'') of the polymer. These chemiresistors made from PVA films whose polymer backbone is 88% hydroxylated (PVA88) have a high sensitivity to water, while chemiresistors made from PVA75 have a higher sensitivity to methanol. The minor differences in polymer composition result in films with different Hildebrand volubility parameters. The relative responses of several different PVA-based chemiresistors to solvents with different volubility parameters are presented. In addition, polyvinyl acetate (PVAC) films with PVA88 are used in an array to distinguish the responses to methanol-water mixtures

Disk Refining and Ultrasonication Treated Sugarcane Bagasse Residues for Poly(Vinyl Alcohol) Bio-composites

Science.gov (United States)

Qingzheng Cheng; Zhaohui Tong; Luisa Dempere; Lonnie Ingram; Letian Wang; J.Y. Zhu

2013-01-01

Disk refining and ultrasonication treated sugarcane bagasse residues reclaimed from the waste stream of a simplified bioethanol process after fermentation were used to fabricate biobased composites with poly(vinyl alcohol) (PVA) by film casting. The morphologies and the size distributions of residue particles were characterized by scanning electronic microscopy and...

Oral delivery of insulin using pH-sensitive hydrogels based on polyvinyl alcohol grafted with acrylic acid/methacrylic acid by radiation

Energy Technology Data Exchange (ETDEWEB)

Nho, Young-Chang [Radiation Application Research Division, Korea Atomic Energy Research Institute, Daejeon 305-600 (Korea, Republic of)]. E-mail: ycnho@kaeri.re.kr; Park, Sung-Eun [Radiation Application Research Division, Korea Atomic Energy Research Institute, Daejeon 305-600 (Korea, Republic of); Kim, Hyung-Il [College of Engineering, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Hwang, Taek-Sung [College of Engineering, Chungnam National University, Daejeon 305-764 (Korea, Republic of)

2005-07-01

The pH-responsive hydrogels were studied as a drug carrier for the protection of insulin from the acidic environment of the stomach before releasing in the small intestine. Hydrogels based on poly(vinyl alcohol) networks grafted with acrylic acid or methacrylic acid were prepared via a two-step process. Poly(vinyl alcohol) hydrogels were prepared by gamma ray irradiation (50 kGy) and then followed by grafting either acrylic acid or methacrylic acid onto this poly(vinyl alcohol) hydrogels with subsequent irradiation (5-20 kGy). These graft hydrogels showed pH-sensitive swelling behavior. These hydrogels were used as carrier for the controlled release of insulin. The in vitro release of insulin was observed for the insulin-loaded hydrogels in a simulated intestinal fluid (pH 6.8) but not in a simulated gastric fluid (pH 1.2). The release behavior of insulin in vivo in a rat model confirmed the effectiveness of the oral delivery of insulin to control the level of glucose.

Oral delivery of insulin using pH-sensitive hydrogels based on polyvinyl alcohol grafted with acrylic acid/methacrylic acid by radiation

International Nuclear Information System (INIS)

Nho, Young-Chang; Park, Sung-Eun; Kim, Hyung-Il; Hwang, Taek-Sung

2005-01-01

The pH-responsive hydrogels were studied as a drug carrier for the protection of insulin from the acidic environment of the stomach before releasing in the small intestine. Hydrogels based on poly(vinyl alcohol) networks grafted with acrylic acid or methacrylic acid were prepared via a two-step process. Poly(vinyl alcohol) hydrogels were prepared by gamma ray irradiation (50 kGy) and then followed by grafting either acrylic acid or methacrylic acid onto this poly(vinyl alcohol) hydrogels with subsequent irradiation (5-20 kGy). These graft hydrogels showed pH-sensitive swelling behavior. These hydrogels were used as carrier for the controlled release of insulin. The in vitro release of insulin was observed for the insulin-loaded hydrogels in a simulated intestinal fluid (pH 6.8) but not in a simulated gastric fluid (pH 1.2). The release behavior of insulin in vivo in a rat model confirmed the effectiveness of the oral delivery of insulin to control the level of glucose

Studying the Properties of Polyvinyl Alcohol/Cellulose Nanofiber/Hydroxyapatite Hybrid Nanocomposite

Directory of Open Access Journals (Sweden)

Mostafa Yahyavi

2015-06-01

Full Text Available Nanocomposite materials have recently attracted much attention because of their desirable and unique physical and mechanical properties. Today, many studies have focused on the preparation of high performance new nanocomposites made of biobased and biodegradable materials as both the matrix and reinforcement phases. Because of biocompatibility, biofunctionality, and biological safety in the body, hydroxyapatite-polyvinyl alcohol composites are vastly used in medical applications, specially in the bone tissue regeneration. The properties of a new generation of nanocomposites consisting of hydroxyapatite nanoparticles and cellulose nanofibers, dispersed in polyvinyl alcohol matrix, were investigated. The percentage by weight of each component in the final formulation and the time of ultrasonication were studied as factors affecting the physical and mechanical properties. Tensile strength, elastic modulus and resistance to water dissolution were evaluated. The results showed that by increasing the percentage by weight of PVA and cellulose nanofibers and ultrasonication time, the tensile strength and elastic modulus increased and the resistance to water dissolution and weight loss decreased. On the other hand, with increasing the amount of hydroxyapatite nanoparticles in the final formulation, the elastic modulus and resistance to water solubility increased, while the tensile strength decreased significantly. Scanning electron microscopy (SEM micrographs were used to find exact correlations between the observed physical and mechanical properties and the structural morphology.

Ethanol-water separation by pervaporation using silicone and polyvinyl alcohol membranes

Directory of Open Access Journals (Sweden)

Chinchiw, S.

2006-09-01

Full Text Available In this research, experiments were carried out to investigate the effects of operating parameters onthe pervaporation performance for the separation of ethanol-water solutions. Composite silicone membranessupported on polysulfone prepared with varied silicone contents and commercial polyvinyl alcohol (Pervap®2211, Sulzer membranes were used. The results showed that the composite silicone/polysulfone membranescoated with 3 wt% of silicone exhibited highest permeation flux with slightly lower separation factor forethanol. Furthermore, it was found that the composite silicone/polysulfone membranes were suitable for theseparation of ethanol from a dilute ethanol solutions. Both the separation factor and permeation flux of the composite membranes increased with increasing temperature and feed concentration. A membrane coated with a 7 wt% silicone gave highest separation factor of 7.32 and permeation flux of 0.44 kg/m2h at 5 wt% ethanol feed concentration and feed temperature of 70ºC. For polyvinyl alcohol membranes, the results showed that the membranes were suitable for the dehydration of concentrated ethanol solutions. The permeation flux increased and the separation factor for water decreased with increasing water feed concentration and temperature. The membrane gave highest separation factor of 248 and permeation flux of 0.02 kg/m2h at 5 wt% water feed concentration and feed temperature of 30ºC.

Study of electrical properties of polyvinylpyrrolidone/polyacrylamide ...

Indian Academy of Sciences (India)

https://www.ias.ac.in/article/fulltext/boms/037/02/0273-0279. Keywords. PVP; PAM; conductivity; activation energy; relaxation time; electric modulus. Abstract. Electrical properties of polyvinylpyrrolidone, polyacrylamide and their blend thin films have been investigated as a function of temperature and frequency. The films ...

Influence of polymer chain architecture of poly(vinyl alcohol) on the inhibition of ice recrystallization

NARCIS (Netherlands)

Olijve, L.L.C.; Hendrix, M.M.R.M.; Voets, I.K.

2016-01-01

Poly(vinyl alcohol) (PVA) is a water-soluble synthetic polymer well-known to effectively block the recrystallization of ice. The effect of polymer chain architecture on the ice recrystallization inhibition (IRI) by PVA remains unexplored. In this work, the synthesis of PVA molecular bottlebrushes is

Poly(vinyl alcohol)/poly(acrylic acid)/TiO2/graphene oxide nanocomposite hydrogels for pH-sensitive photocatalytic degradation of organic pollutants

International Nuclear Information System (INIS)

Moon, Young-E; Jung, Gowun; Yun, Jumi; Kim, Hyung-Il

2013-01-01

Graphical abstract: The photocatalytic removal of pollutants was improved by the two-step mechanism based on the adsorption of pollutants by hydrogel and the effective decomposition by combination of TiO 2 and graphene oxide. -- Highlights: • pH sensitive PVA/PAAc hydrogels were prepared by radical polymerization and condensation reaction. • PVA/PAAc/TiO 2 /graphene oxide nanocomposite hydrogels were used for treatment of basic waste water. • Photocatalytic acitivity of TiO 2 was improved by incorporation of graphene oxide. • Photocatalytic decomposition by nanocomposite hydrogel was improved by increasing pH. -- Abstract: Poly(vinyl alcohol)/poly(acrylic acid)/TiO 2 /graphene oxide nanocomposite hydrogels were prepared using radical polymerization and condensation reaction for the photocatalytic treatment of waste water. Graphene oxide was used as an additive to improve the photocatalytic activity of poly(vinyl alcohol)/poly(acrylic acid)/TiO 2 nanocomposite hydrogels. Both TiO 2 and graphene oxide were immobilized in poly(vinyl alcohol)/poly(acrylic acid) hydrogel matrix for an easier recovery after the waste water treatment. The photocatalytic activity of poly(vinyl alcohol)/poly(acrylic acid)/TiO 2 /graphene oxide nanocomposite hydrogels was evaluated on the base of the degradation of pollutants by using UV spectrometer. The improved removal of pollutants was due to the two-step mechanism based on the adsorption of pollutants by nanocomposite hydrogel and the effective decomposition of pollutants by TiO 2 and graphene oxide. The highest swelling of nanocomposite hydrogel was observed at pH 10 indicating that poly(vinyl alcohol)/poly(acrylic acid)/TiO 2 /graphene oxide nanocomposite hydrogels were suitable as a promising system for the treatment of basic waste water

Oxidative mineralization and characterization of polyvinyl alcohol for compatibility with tank farm processing chemistry

Energy Technology Data Exchange (ETDEWEB)

Oji, L.N.

2000-01-04

Polyvinyl alcohol (PVA) material has been evaluated for use as a cost-effective substitute for conventional cellulose-based disposal materials (decontamination mops and wipes), plastic bags, and disposable personal protection clothing, that are currently used at Savannah River Site. This study also provides process design criteria for ultraviolet/ultrasonic/hydrogen peroxide PVA reactor system.

Oxidative mineralization and characterization of polyvinyl alcohol for compatibility with tank farm processing chemistry

International Nuclear Information System (INIS)

Oji, L.N.

2000-01-01

Polyvinyl alcohol (PVA) material has been evaluated for use as a cost-effective substitute for conventional cellulose-based disposal materials (decontamination mops and wipes), plastic bags, and disposable personal protection clothing, that are currently used at Savannah River Site. This study also provides process design criteria for ultraviolet/ultrasonic/hydrogen peroxide PVA reactor system

Physicochemical characteristics of gamma irradiation crosslinked poly(vinyl alcohol)/magnetite ferrogel composite

OpenAIRE

Marinović-Cincović, Milena T.; Radosavljević, Aleksandra N.; Krstić, Jelena I.; Spasojević, Jelena P.; Bibić, Nataša M.; Mitrić, Miodrag N.; Kačarević-Popović, Zorica M.

2014-01-01

Magnetic field sensitive gels, ferrogels are new promising class of hydrogels. The coupling of hydrogels and magnetic particles has potential application in soft actuators such as artificial muscles or for hyperthermia application. Here a composite of magnetite particles (Fe3O4) and poly(vinyl alcohol) (PVA) hydrogel is developed using gamma irradiation as a crosslinking agent. PVA and Fe3O4 were chosen because of their well-established biocompatibility, ra...

Poly(vinyl alcohol)-based film potentially suitable for antimicrobial packaging applications.

Science.gov (United States)

Musetti, Alessandro; Paderni, Katia; Fabbri, Paola; Pulvirenti, Andrea; Al-Moghazy, Marwa; Fava, Patrizia

2014-04-01

This work aimed at developing a thin and water-resistant food-grade poly(vinyl alcohol) (PVOH)-based matrix able to swell when in contact with high moisture content food products without rupturing to release antimicrobial agents onto the food surface. This film was prepared by blending PVOH and 7.20% (wt/wt of PVOH) of poly(ethylene glycol) (PEG) with citric acid as crosslinking agent. The film-forming solution was then casted onto a flat surface and the obtained film was 60 μm in thickness and showed a good transparency (close to T = 100%) in the visible region (400 to 700 nm). After immersion in water for 72 h at room temperature, the crosslinked matrix loses only 19.2% of its original weight (the percentage includes the amount of unreacted crosslinking agent, antimicrobial in itself). Water content, degree of swelling, and crosslinking density of the film prove that the presence of PEG diminishes the hydrophilic behavior of the material. Also the mechanical properties of the wet and dry film were assessed. Alongside this, 2.5% (wt/wt of dry film) of grapefruit seed extract (GSE), an antimicrobial agent, was added to the film-forming solution just before casting and the ability of the plastic matrix to release the additive was then evaluated in vitro against 2 GSE-susceptible microorganisms, Salmonella enteritidis and Listeria innocua. The results indicate that the developed matrix may be a promising food-grade material for the incorporation of active substances. © 2014 Institute of Food Technologists®

Tailor-made starch-based conjugates containing well-defined poly(vinyl acetate and its derivative poly(vinyl alcohol

Directory of Open Access Journals (Sweden)

2011-06-01

Full Text Available Reversible addition-fragmentation chain transfer (RAFT polymerization was adopted to synthesize starch-based conjugates that possessed controllable architecture and properties. Starch-based xanthate agent was prepared and applied as chain transfer agent to conduct the living/controlled polymerization (LCP of vinyl acetate, which generated tailor-made conjugates of starch and well-defined poly(vinyl acetate (SVAc. The relevant derivatives, conjugates of starch and chain length-controlled poly(vinyl alcohol (SVA, were obtained subsequently. Various characterizations such as Fourier transform infrared spectra (FTIR, ultraviolet-visible spectroscopy (UV, proton nuclear magnetic resonance (1H NMR, gel permeation chromatography (GPC, X-ray diffraction (XRD, Thermogravimetric analysis (TGA, and dynamic mechanical thermal analysis (DMTA were performed to examine the structure of intermediates and the starch-based conjugates. Static contact angle measurements revealed that the hydrophilic character of starch-based conjugates was tunable. Well-defined SVAc was amphiphilic and it was able to self-assemble into size controllable micelles, which was verified by contact angles, transmission electron microscopy (TEM and dynamic light scattering (DLS tests. SVA exhibited much higher capability to form physically cross-linked hydrogel than starch did. Both the characteristic of SVAc and SVA were chain length-dependent.

Water absorption and its effect on the tensile properties of tapioca starch/polyvinyl alcohol bioplastics

NARCIS (Netherlands)

Judawisastra, H.; Sitohang, Ramona; Marta, L.; Mardiyati,

2017-01-01

Tapioca is one of the largest sources of starch and makes it suitable to be used for bioplastic material. Addition of polyvinyl alcohol (PVA) has been shown to successfully reduce the brittleness of starch bioplastic. This study aims to investigate the influence of PVA addition to water absorption

Effects of Concentration of Organically Modified Nanoclay on Properties of Sulfonated Poly(vinyl alcohol Nanocomposite Membranes

Directory of Open Access Journals (Sweden)

Apiradee Sanglimsuwan

2011-01-01

Full Text Available Electrolyte nanocomposite membranes for proton exchange membrane fuel cells and direct methanol fuel cells were prepared by carrying out a sulfonation of poly(vinyl alcohol with sulfosuccinic acid and adding a type of organically modified montmorillonite (layered silicate nanoclay commercially known as Cloisite 93A. The effects of the different concentrations (0, 2, 4, 6, 8 wt. % of the organoclay in the membranes on water uptake, ion exchange capacity (IEC, proton conductivity, and methanol permeability were measured, respectively, via gravimetry, titration, impedance analysis, and gas chromatography techniques. The IEC values remained constant for all concentrations. Water uptakes and proton conductivities of the nanocomposite membranes changed with the clay content in a nonlinear fashion. While all the nanocomposite membranes had lower methanol permeability than Nafion115, the 6% concentration of Cloisite 93A in sulfonated poly(vinyl alcohol membrane displayed the greatest proton conductivity to methanol permeability ratio.

Effect of gamma radiation on the poly(vinyl alcohol)

International Nuclear Information System (INIS)

Terence, M.C.; Guedes, S.M.L.

2000-01-01

The poly(vinyl alcohol) (PVAL) is a polymer used as bio material. The PVAL was used as ocular insert and may be used as a drug delivery system (DDS) for pair PVAL/gancyclovir, where the last one is used for treatment of people with retinitis caused by cytomegalovirus. These inserts are crosslinked systems. The crosslink was induced by gamma radiation applied in polymer. The samples of PVAL was irradiated by gamma rays with doses in the range 0 to 100 kGy. On irradiated PVAL samples was observed a low yellowness, attributed to the formation of polymeric radicals that are stable in the structure of the polymer, from radiolysis of PVAL. (author)

Polyvinyl alcohol coating of polystyrene inertial confinement fusion targets

International Nuclear Information System (INIS)

Annamalai, P.; Lee, M.C.; Crawley, R.L.; Downs, R.L.

1985-01-01

An inertial confinement fusion (ICF) target made of polystyrene is first levitated in an acoustic field. The surface of the target is then etched using an appropriate solution (e.g., cyclohexane) to enhance the wetting characteristics. A specially prepared polyvinyl alcohol solution is atomized using an acoustic atomizer and deposited on the surface of the target. The solution is air dried to form a thin coating (2 μm) on the target (outside diameter approx.350--850 μm). Thicker coatings are obtained by repeated applications of the coating solution. Preliminary results indicate that uniform coatings may be achievable on the targets with a background surface smoothness in the order of 1000 A

Novel Polyvinyl Alcohol/Styrene Butadiene Rubber Latex/Carboxymethyl Cellulose Nanocomposites Reinforced with Modified Halloysite Nanotubes

Directory of Open Access Journals (Sweden)

Yanjun Tang

2013-01-01

Full Text Available Novel polyvinyl alcohol (PVA/styrene butadiene rubber (SBR latex/carboxymethyl cellulose (CMC/halloysite nanotubes (HNTs nanocomposites were successfully prepared through physical blending. The as-obtained PVA/SBR/CMC/HNTs nanocomposites were coated on the surface of old corrugated container (OCC-based paper in an effort to improve the mechanical properties of paper. To improve the dispersion of HNTs and enhance the compatibility between HNTs and polymer matrix, HNTs were modified with titanate coupling agent (TCA. FT-IR, together with TGA, confirmed that TCA was grafted onto the surface of HNTs successfully. XRD demonstrated that the crystal structures of HNTs remained almost unchanged. TEM showed that modified HNTs exhibited good dispersion and possessed nanotubular structures with an outer diameter of around 50 nm and an inner diameter of about 20 nm. SEM gave an indication that modified HNTs were dispersed more uniformly than unmodified HNTs within PVA/SBR/CMC matrix. Rheological measurement exhibited that surface modification process enhanced the compatibility between HNTs and polymer matrix, thus resulting in the decreased viscosity of nanocomposites. In comparison with unmodified HNTs, modified HNTs were found to contribute more to the enhancement in mechanical properties, which might be attributed to the better dispersion and compatibility of modified HNTs evidenced by TEM, SEM, and rheological measurement.

Effect of Poly(Vinyl Alcohol) Addition on the Properties of Hydrothermal Derived Calcium Phosphate Cement for Bone Filling Materials

Science.gov (United States)

Razali, N. N.; Sopyan, I.; Mel, M.; Salleh, H. M.; Rahman, M. M.; Singh, R.

2017-06-01

The effect of addition of poly(vinyl alcohol) on hydrothermal derived calcium phosphate cement has been studied. The precursors used to prepare the cement were calcium oxide (CaO) and ammonium dihydrogen phosphate (NH4H2PO4); the reaction was conducted in water at 80-100°C. To improve properties of CPC, poly(vinyl alcohol) (PVA) of 1wt% and 2wt% was added to the liquid phase of CPC and the results were compared to CPC without PVA addition. The addition of PVA was proved to bring remarkable effects on cohesion, setting time and mechanical strength of CPC which make it suitable physically for injectable bone filler applications.

Feedback controlled fuel injection system can accommodate any alcohol-gasoline blend

Energy Technology Data Exchange (ETDEWEB)

Pefley, R K; Pullman, J B; Suga, T P; Espinola, S

1980-01-01

A fuel metering system has been adapted and permits operation on all blends of alcohols and gasoline ranging from pure gasoline to pure ethanol and methanol. It is a closed loop electronic feedback controlled fuel injection system (EFI) with exhaust oxygen sensor. The system is used by Toyota Motor Company in their Supra and Cressida models in conjunction with a 3-way catalytic exhaust system. These models meet California exhaust and evaporative emission standards. An unmodified model has been tested on alcohol gasoline blends from pure gasoline to 50% ethanol-50% gasoline and 30% methanol-70% gasoline and found to meet all exhaust and evaporative emissions standards. A Cressida with modified EFI system is currently being tested. It is capable of operating on pure gasoline, pure methanol or ethanol and all intermediate blends. The testing to date shows that the vehicle meets all exhaust emissions standards while operating over the blend range from pure gasoline to pure ethanol while maintaining driveability and energy based fuel economy. The paper will present the total test evidence for all gasoline-alcohol blends. This will include exhaust and evaporative emissions, fuel economy and driveability as determined in accordance with United States Federal Test Procedures. Additionally, the paper will report experiences accumulated from road operation of the vehicle over a six-month period.

Improved permeation performance and fouling-resistance of Poly(vinyl chloride/Polycarbonate blend membrane with added Pluronic F127

Directory of Open Access Journals (Sweden)

Supateekan Pacharasakoolchai

2014-04-01

Full Text Available The aim of this work was to prepare and characterize poly(vinyl chloride (PVC/polycarbonate (PC blend membranes for use in ultrafiltration. Pluronic F127 was used as an additive to modify the membrane surface of the PVC/PC blended membranes. The PVC/PC blend membrane was first prepared using the phase inversion method from a casting solution of PVC with small amount of PC in N-methylpyrrolidone (NMP and water as the non-solvent. The morphologies structure and properties, such as tensile strength, water flux, and bovine serum albumin (BSA rejection of the blend membrane were studied. Increased amounts of PC resulted in an increase in the water flux and ability to reject protein. A concentration of 0.75 wt% PC provided the best improvement in tensile strength of blend membrane. Addition of different amounts of pluronic F127 to the casting solution of PVC/PC with a PC concentration of 0.75 wt% resulted in a decrease in the water contact angle that demonstrated the improvement of hydrophilicity of blend membrane. Scanning electron microscopy photographs showed that the modified PVC/PC membranes had a bigger pore volume in the porous sub-layer compared to the PVC/PC control membrane. The PVC/PC membrane with added Pluronic F127 exhibited a much higher flux and rejection of BSA in a protein filtration experiment than the PVC/PC membrane. An increase in flux recovery ratio of PVC/PC/pluronic 127 blend membrane indicated that the modified membranes could reduce membrane fouling useful for ultrafiltration.

Harvesting and blending options for lower alcohol wines: a sensory and chemical investigation.

Science.gov (United States)

Longo, Rocco; Blackman, John W; Antalick, Guillaume; Torley, Peter J; Rogiers, Suzy Y; Schmidtke, Leigh M

2018-01-01

Lower alcohol wines often have a poor reputation among consumers, in part due to their unsatisfactory flavours such as reduced overall aroma intensity or herbaceous characters. The aim of this study, performed on Verdelho and Petit Verdot, was to quantify the effectiveness of a monovarietal blend in which wines made from less ripe grapes were blended with an equivalent volume of a wine vinified from riper fruit to produce wines with a lower alcohol content and desirable ripe fruit flavours. Eleven and 13 attributes, for Verdelho and Petit Verdot, respectively, were selected during sensory descriptive analysis. Intensities of perceived 'acidity', 'sweetness' and 'alcohol' attributes were significantly different (P ≤ 0.05) between the blend (8.8 ± 0.1% v/v) and mature Verdelho (10.3 ± 0.1% v/v) wines, while no significant differences were found between the Petit Verdot blend (11.0 ± 0.1% v/v) and mature (12.6 ± 0.2% v/v) treatments. Volatile composition of wines was assessed using HS-SPME-GC-MS. Partial least square regression suggested relationships between sensory descriptors and chemical attributes in the wines, as well as the modifications of sensory and compositional profiles following blending. The blending practice described allowed the production of wines with lower alcohol content while retaining similar sensory profiles of the later harvested, riper fruit wines. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Enhancement of the thermal and mechanical properties of polyurethane/polyvinyl chloride blend by loading single walled carbon nanotubes

Directory of Open Access Journals (Sweden)

A.M. Hezma

2017-06-01

Full Text Available Structural, thermal, and mechanical properties of pure blend and nanocomposites based on polyurethane (PU and polyvinyl chloride (PVC doped with low different content of single walled-carbon nanotubes (SWCNTs were studied. The nanocomposites at different concentration were prepared via casting technique. The interaction between PU/PVC and CNTs were examined via FT-IR studies. The changes in the structures of the nanocomposites were examined using X- Ray Diffraction (XRD, and the results indicated that the amorphous domains of nanocomposites increased with increasing SWCNTs content. Transmission electron microscope (TEM observation indicated that SWCNTs surface was wrapped with the polymer with the thermal properties of nanocomposites improved. The mechanical behavior of the nanocomposites was evaluated as a function of SWCNTs content. The main enhancement in tensile properties was observed, e.g., the tensile strength and elastic modulus increased compared with the pure blend, which may be attributed to the interaction and adhesion between CNTs and the polymer matrices due to the hydrogen bonding between carbonyl groups (C=O of polymer blend chains and carboxylic acid (COOH groups of CNTs.

Performance properties and antibacterial activity of crosslinked films of quaternary ammonium modified starch and poly(vinyl alcohol).

Science.gov (United States)

Sekhavat Pour, Zahra; Makvandi, Pooyan; Ghaemy, Mousa

2015-09-01

There has been a growing interest in developing antibacterial polymeric materials. In the present work, novel antibacterial cross-linked blend films were prepared based on polyvinyl alcohol (PVA) and quaternary ammonium starch (ST-GTMAC) using citric acid (CA) as plasticizer and glutaraldehyde (GA) as cross-linker. The ST-GTMAC was successfully synthesized from reaction between water-soluble oxidized starch and glycidyltrimethylammonium chloride (GTMAC). The effect of ST-GTMAC, CA and GA contents on the swelling, solubility, mechanical and thermal properties of the films was investigated. It was found that incorporation of ST-GTMAC reduced UV-transmittance and provided antibacterial properties, increasing GA content increased tensile strength and decreased solubility and swelling degree of the films, while CA acted as plasticizer when its concentration was above 10 wt%. The results showed that ST-GTMAC/PVA/CA/GA film has fair antibacterial activity against Gram-positive (Staphylococcus aureus and Bacillus subtilis) and Gram-negative (Escherichia coli and Pseudomonas aeruginosa) bacteria. These results suggest that the prepared film might be used as potential antibacterial material in medical and packaging applications. Copyright © 2015 Elsevier B.V. All rights reserved.

The Effects of Montmorillonite and Cellulose Nanocrystals on Physical Properties of Carboxymethyl Cellulose/Polyvinyl Alcohol Blend Films

Directory of Open Access Journals (Sweden)

Leila Abolghasemi Fakhri

2013-01-01

Full Text Available Cellulose nanocrystal  CNC is a type of nanomaterial which is produced by  partial hydrolysis of cellulose and elimination of its amorphous regions. CNC has several advantages such as biodegradability and safety toward human health. In this study, CNC was produced from cotton linters and methods such as transmission electron microscopy and atomic force microscopy were used for confrmation of nanoscale  size production of cellulose crystals. Carboxymethyl cellulose  CMC/polyvinyl alcohol  PVA-nanoclay  MMT and CMC-PVA-CNC flms, containing 3-10% (wt/wt CMC nanofllers, were prepared by casting method and their physical properties were compared in order to approve the use of CNC instead of MMT for its contribution in improving the physical properties of carboxymethyl cellulose-based  flms.  The  X-ray  diffraction  results  indicated  the  formation  of  an exfoliated nanostructure at all nanoparticle concentrations. The results showed that there was no signifcant difference (p < 0.5 between the moisture absorption properties of flms containing the two types of nanofller. The flms containing nanoclay showed higher mechanical strength compared to those containing CNC. The ultimate tensile strengths of the flms containing 10% nanoclay and CNC were higher than the control flm (69.72% and 47.05%, respectively.

Evaluation of hemocompatibility and endothelialization of hybrid poly(vinyl alcohol) (PVA)/gelatin polymer films.

Science.gov (United States)

Ino, Julia M; Sju, Ervi; Ollivier, Véronique; Yim, Evelyn K F; Letourneur, Didier; Le Visage, Catherine

2013-11-01

Engineered grafts are still needed for small diameter blood vessels reconstruction. Ideal materials would prevent thrombosis and intimal hyperplasia by displaying hemocompatibility and mechanical properties close to those of native vessels. In this study, poly(vinyl alcohol) (PVA)/gelatin blends were investigated as a potential vascular support scaffold. We modified a chemically crosslinked PVA hydrogel by incorporation of gelatin to improve endothelial cell attachment with a single-step method. A series of crosslinked PVA/gelatin films with specific ratios set at 100:0, 99:1, 95:5, and 90:10 (w/w) were prepared and their mechanical properties were examined by uniaxial tensile testing. Tubes, obtained from sutured films, were found highly compliant (3.1-4.6%) and exhibited sufficient mechanical strength to sustain hemodynamic strains. PVA-based hydrogels maintained low level of platelet adhesion and low thrombogenic potential. Endothelial cell adhesion and proliferation were drastically improved on PVA/gelatin films with a feed gelatin content as low as 1% (w/w), leading to the formation of a confluent endothelium. Hydrogels with higher gelatin content did not sustain complete endothelialization because of modifications of the film surface, including phase segregation and formation of microdomains. Thus, PVA/gelatin (99:1, w/w) hydrogels appear as promising materials for the design of endothelialized vascular materials with long-term patency. Copyright © 2013 Wiley Periodicals, Inc.

Localization of xanthine oxidoreductase activity using the tissue protectant polyvinyl alcohol and final electron acceptor Tetranitro BT

NARCIS (Netherlands)

Kooij, A.; Frederiks, W. M.; Gossrau, R.; van Noorden, C. J.

1991-01-01

We have detected xanthine oxidoreductase activity in unfixed cryostat sections of rat and chicken liver, rat duodenum, and bovine mammary gland using the tissue protectant polyvinyl alcohol, the electron carrier 1-methoxyphenazine methosulfate, the final electron acceptor Tetranitro BT, and

Preparation of polyvinyl alcohol graphene oxide phosphonate film and research of thermal stability and mechanical properties.

Science.gov (United States)

Li, Jihui; Song, Yunna; Ma, Zheng; Li, Ning; Niu, Shuai; Li, Yongshen

2018-05-01

In this article, flake graphite, nitric acid, peroxyacetic acid and phosphoric acid are used to prepare graphene oxide phosphonic and phosphinic acids (GOPAs), and GOPAs and polyvinyl alcohol (PVA) are used to synthesize polyvinyl alcohol graphene oxide phosphonate and phosphinate (PVAGOPs) in the case of faint acidity and ultrasound irradiation, and PVAGOPs are used to fabricate PVAGOPs film, and the structure and morphology of GOPAs, PVAGOPs and PVAGOPs film are characterized, and the thermal stability and mechanical properties of PVAGOPs film are investigated. Based on these, it has been proved that GOPAs consist of graphene oxide phosphonic acid and graphene oxide phosphinic acid, and there are CP covalent bonds between them, and PVAGOPs are composed of GOPAs and PVA, and there are six-member lactone rings between GOPAs and PVA, and the thermal stability and mechanical properties of PVAGOPs film are improved effectively. Copyright © 2018 Elsevier B.V. All rights reserved.

The Preparation of Graphene Reinforced Poly(vinyl alcohol Antibacterial Nanocomposite Thin Film

Directory of Open Access Journals (Sweden)

Yuan-Cheng Cao

2015-01-01

Full Text Available Methylated melamine grafted polyvinyl benzylchloride (mm-g-PvBCl was prepared which was used as additive in poly(vinyl alcohol (PVA and graphene nanosheets (GNs were used to reinforce the mechanical strength. Using casting method, antimicrobial nanocomposite films were prepared with the polymeric biocide loading lever of 1 wt%, 5 wt%, and 10 wt%. Thermogravimetric analysis (TGA characterization revealed the 2.0 wt% of graphene content in resultant nanocomposites films. XRD showed that the resultant GNs 2 theta was changed from 16.6 degree to 23.3 degree. Using Japanese Industry Standard test methods, the antimicrobial efficiency for the loading lever of 1 wt%, 5 wt%, and 10 wt% was 92.0%, 95.8%, and 97.1%, respectively, against gram negative bacteria E. coli and 92.3%, 99.6%, and 99.7%, respectively, against the gram positive S. aureus. These results indicate the prepared nanocomposite films are the promising materials for the food and drink package applications.

Sodium deoxycholate functionalized graphene and its composites with polyvinyl alcohol

International Nuclear Information System (INIS)

Wang Lanwei; Liao Ruijuan; Tang Zhenghai; Lei Yanda; Guo Baochun

2011-01-01

Sodium deoxycholate (SDC), a kind of bile derivative, is used to noncovalently functionalize graphene. Stable and high concentration (up to 20 mg ml -1 ) of graphene colloid is obtained. The stabilization mechanism is revealed to be hydrophobic interaction, electrostatic repulsion and hydrogen bonding. Single-layer and few-layer graphene are obtained in the colloid. Subsequently, the obtained graphene sheets are incorporated into a polyvinyl alcohol (PVA) matrix by solution casting to fabricate PVA/graphene composites. Morphological observations substantiate the homogeneous dispersion of graphene in the PVA matrix and strong interfacial adhesion between them. Significant improvements in tensile strength and modulus of the composite films are observed.

A novel reverse osmosis membrane modified by polyvinyl alcohol with maleic anhydride crosslinking

Science.gov (United States)

Samnani, Mohit; Rathod, Harshad; Raval, Hiren

2018-03-01

In the era of increasing energy crisis, it is inevitable to decrease process energy consumption to increase process viability and curtail green-house gas emission. The Reverse Osmosis plant requires significant energy to transfer water overcoming the osmotic pressure. This paper focuses on increasing the water flux for Thin Film Composite Reverse Osmosis (TFC RO) membrane without compromising salt rejection performance leading to the environmentally friendly and economically attractive process. The virgin TFC RO membrane was exposed to solution of sodium hypochlorite of concentration 2000 mg l-1 for 1 h to activate the surface of the membrane, followed by the treatment with the mixture of polyvinyl alcohol and maleic anhydride with varying concentrations for 1 h and curing in the oven at 80 °C temperature for 10 min. Out of all the treated membranes, the membrane treated with 2000 mg l-1 polyvinyl alcohol and 1000 mg l-1 maleic anhydride demonstrated the highest salt rejection of 96.83 % with 2% increase as compared to the virgin TFC RO membrane. The water flux of the membrane was around 44% higher than the virgin TFC RO membrane. The membrane samples were characterized by atomic force micrographs, ATR-FTIR, Nuclear magnetic resonance and Dynamic mechanical analysis.

Characterization and electrical properties of polyvinyl alcohol based polymer electrolyte films doped with ammonium thiocyanate

Energy Technology Data Exchange (ETDEWEB)

Kulshrestha, N., E-mail: niharikakul@gmail.com; Chatterjee, B.; Gupta, P.N., E-mail: guptapn07@yahoo.co.in

2014-05-01

Highlights: • Polyvinyl alcohol (PVA). • Ammonium thiocyanate (NH{sub 4}SCN). • Electrical conductivity. • Fractals. - Abstract: In this communication, films of polyvinyl alcohol (PVA) polymer complexed with ammonium thiocyanate (NH{sub 4}SCN) salt were studied. XRD (X-ray diffraction) was used to study the complexation of salt with the polymer matrix and amorphicity in the films. DSC (differential scanning calorimetry) studies showed that the glass transition temperatures (T{sub g}) of the PVA:NH{sub 4}SCN complexed films were less than pristine PVA. Raman analysis was analyzed in order to study the change in the vibrational bands due to the complexation of salt with PVA. Optical micrographs confirm the fractal formation in 75:25 and 70:30 PVA:NH{sub 4}SCN films. Ionic transference number was estimated by Wagner's polarization method and its large value indicates that conduction takes place mainly due to mobile ionic species. Maximum conductivity ∼10{sup −3} S/cm at room temperature was obtained for 70:30 ratio of PVA: NH{sub 4}SCN polymer electrolyte films.

Viscometric investigation of compatibilization of the poly(vinyl chloride)/poly(ethylene-co-vinyl acetate) blends by terpolymer of maleic anhydride styrene vinyl acetate

Science.gov (United States)

İmren, Dilek; Boztuğ, Ali; Yılmaz, Ersen; Zengin, H. Bayram

2008-11-01

In this study, a blend of poly(vinyl chloride) (PVC)/ethylene-co-vinyl acetate (EVA) was compatibilized by terpolymer of maleic anhydride-styrene-vinyl acetate (MAStVA) used as a compatibilizer. It was prepared the blends of 50/50 PVC/EVA containing 2-10% of the terpolymer. The compatibility experiences of these blends were investigated by using viscometric method in the range of concentrations (0.5-2.0 g dL -1) where tetrahydrofuran (THF) is the solvent. The interaction parameter (Δ b) was used to study the miscibility and compatibility of polymer blend in solution, obtained from the modified Krigbaum and Wall theory. Turbidity and FTIR measurements were also used to investigate the miscibility of this pair of polymers. The values of the relative viscosities of the each polymer solution and their blends were measured by a Cannon-Fenske type viscometer. In consequence of the study, it was observed that a considerable improvement was achieved in the miscibility of PVC/EVA blends by adding among 5 and 10 wt% of compatibilizer.

Enzyme cytochemistry of unfixed leukocytes and bone marrow cells using polyvinyl alcohol for the diagnosis of leukemia

NARCIS (Netherlands)

van Noorden, C. J.; Vogels, I. M.; van Wering, E. R.

1989-01-01

Cytochemical methods for the demonstration of enzyme activities in blood and bone marrow cells were systematically improved by the addition of an inert polymer, polyvinyl alcohol (PVA), to the incubation medium and by using optimized reaction media. The methods investigated were tetrazolium salt

Poly(vinyl alcohol) composite films with high percent elongation prepared from amylose-fatty ammonium salt inclusion complexes

Science.gov (United States)

Amylose inclusion complexes prepared from cationic fatty ammonium salts and jet-cooked high amylose starch were combined with poly(vinyl alcohol) (PVOH) to form glycerol-plasticized films. Their tensile properties were compared with similar films prepared previously with analogous anionic fatty acid...

Fabrication and Characterization of Electrospun Wool Keratin/Poly(vinyl alcohol) Blend Nanofibers

OpenAIRE

Shuai Li; Xu-Hong Yang

2014-01-01

Wool keratin/poly(vinyl alcohol) (PVA) blend nanofibers were fabricated using the electrospinning method in formic acid solutions with different weight ratios of keratin to PVA. The resultant blend nanofibers were characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR), X-ray diffraction (XRD), thermal gravimetric analysis (TGA), and tensile test. SEM images showed that the diameter of the blend nanofibers was affected by the content of keratin in blend solution...

Combination effect of melamine polyphosphate and graphene on flame retardant properties of poly(vinyl alcohol)

International Nuclear Information System (INIS)

Huang Guobo; Liang Huading; Wang Yong; Wang Xu; Gao Jianrong; Fei Zhengdong

2012-01-01

Highlights: ► PVA/graphene/MPP composites were prepared by solvent blending. ► PVA/graphene systems improved the flame retardancy of the nanocomposites. ► Flame retardation mechanism was explained by SEM, FT-IR and XPS. - Abstract: A novel flame retardant poly(vinyl alcohol) (PVA)/melamine polyphosphate (MPP)–graphene nanocomposite has been prepared by solvent blending. Results from X-ray diffraction (XRD) and transmission electron microscopy (TEM) suggest that an excellent dispersion of exfoliated graphene and MPP in the PVA matrix was achieved. The thermal and flammability properties of the nanocomposite were investigated using thermogravimetry, cone calorimetry, and flammability tests (UL 94 and LOI). The presence of both MPP and graphene in the polymer matrix led to an enhanced thermal stability and significantly reduced flammability for the nanocomposite. PVA composites filled with 10 wt% MPP and 1 wt% graphene (PVA/G1/MPP10) achieved the LOI value of 29.6 and UL-94 V0 grade. Compared to pure PVA, the peak heat release rate (PHRR) of PVA/G1/MPP10 is reduced by about 60%. Meanwhile, the mechanical properties of PVA/G1/MPP10 composites exhibit almost no deterioration compared with pure PVA. The morphology and composition of residues generated after cone calorimeter tests were investigated by scanning electronic microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS). The SEM images showed the compact and dense intumescent char jammed with graphene sheets was formed for PVA/G1/MPP10 during combustion. The results of XPS confirmed that carbon content of the char for PVA/G1/MPP10 is increased obviously by the combination effect of the flame retardant MPP and graphene.

Effect of borax concentration on the structure of Poly(Vinyl Alcohol) gels

Science.gov (United States)

Lawrence, Mathias B.; Desa, J. A. E.; Aswal, V. K.

2012-06-01

Poly(Vinyl Alcohol) hydrogels cross-linked with varying concentrations of borax have been studied using Small-Angle Neutron Scattering and X-Ray Diffraction. The intensity of scattering increases with borax concentration from 1 mg/ml up to 2 mg/ml and falls thereafter for 4 mg/ml, increasing again for a concentration of 10 mg/ml. The mesoscopic structural changes that cause these trends in the SANS data are in keeping with the variations in the X-ray diffraction patterns pertaining to structures within the PVA chains.

Ultrasonic-assisted preparation of graphene oxide carboxylic acid polyvinyl alcohol polymer film and studies of thermal stability and surface resistivity.

Science.gov (United States)

Li, Yongshen; Li, Jihui; Li, Yuehai; Li, Yali; Song, Yunan; Niu, Shuai; Li, Ning

2018-01-01

In this paper, flake graphite, nitric acid and acetic anhydride are used to prepare graphene oxide carboxylic acid (GO-COOH) via an ultrasonic-assisted method, and GO-COOH and polyvinyl alcohol polymer (PVA) are used to synthesize graphene oxide carboxylic acid polyvinyl alcohol polymer (GO-COOPVA) via the ultrasonic-assisted method, and GO-COOPVA is used to manufacture graphene oxide carboxylic acid polyvinyl alcohol polymer film (GO-COOPVA film) via a solidification method, and the structure and morphology of GO-COOH, GO-COOPVA and GO-COOPVA film are characterized, and the thermal stability and surface resistivity are measured in the case of the different amount of GO-COOH. Based on the characterization and measurement, it has been successively confirmed and attested that carboxyl groups implant on 2D lattice of GO to form GO-COOH, and GO-COOH and PVA have the esterification reaction to produce GO-COOPVA, and GO-COOPVA consists of 2D lattice of GO-COOH and the chain of PVA connected in the form of carboxylic ester, and GO-COOPVA film is composed of GO-COOPVA, and the thermal stability of GO-COOPVA film obviously improves in comparison with PVA film, and the surface resistivity of GO-COOPVA film clearly decreases. Copyright © 2017 Elsevier B.V. All rights reserved.

Biomechanical analysis of a salt-modified polyvinyl alcohol hydrogel for knee meniscus applications, including comparison with human donor samples.

Science.gov (United States)

Hayes, Jennifer C; Curley, Colin; Tierney, Paul; Kennedy, James E

2016-03-01

The primary objective of this research was the biomechanical analysis of a salt-modified polyvinyl alcohol hydrogel, in order to assess its potential for use as an artificial meniscal implant. Aqueous polyvinyl alcohol (PVA) was treated with a sodium sulphate (Na2SO4) solution to precipitate out the polyvinyl alcohol resulting in a pliable hydrogel. The freeze-thaw process, a strictly physical method of crosslinking, was employed to crosslink the hydrogel. Development of a meniscal shaped mould and sample housing unit allowed the production of meniscal shaped hydrogels for direct comparison to human meniscal tissue. Results obtained show that compressive responses were slightly higher in PVA/Na2SO4 menisci, displaying maximum compressive loads of 2472N, 2482N and 2476N for samples having undergone 1, 3 and 5 freeze-thaw cycles respectively. When compared to the human meniscal tissue tested under the same conditions, an average maximum load of 2467.5N was observed. This suggests that the PVA/Na2SO4 menisci are mechanically comparable to the human meniscus. Biocompatibility analysis of PVA/Na2SO4 hydrogels revealed no acute cytotoxicity. The work described herein has innovative potential in load bearing applications, specifically as an alternative to meniscectomy as replacement of critically damaged meniscal tissue in the knee joint where repair is not viable. Copyright © 2015 Elsevier Ltd. All rights reserved.

Impedance studies of a green blend polymer electrolyte based on PVA and Aloe-vera

Science.gov (United States)

Selvalakshmi, S.; Mathavan, T.; Vijaya, N.; Selvasekarapandian, Premalatha, M.; Monisha, S.

2016-05-01

The development of polymer electrolyte materials for energy generating and energy storage devices is a challenge today. A new type of blended green electrolyte based on Poly-vinyl alcohol (PVA) and Aloe-vera has been prepared by solution casting technique. The blending of polymers may lead to the increase in stability due to one polymer portraying itself as a mechanical stiffener and the other as a gelled matrix supported by the other. The prepared blend electrolytes were subjected to Ac impedance studies. It has been found out that the polymer film in which 1 gm of PVA was dissolved in 40 ml of Aloe-vera extract exhibits highest conductivity and its value is 3.08 × 10-4 S cm-1.

Effect of homopolymer poly(vinyl acetate on compatibility and mechanical properties of poly(propylene carbonate/poly(lactic acid blends

Directory of Open Access Journals (Sweden)

J. Gao

2012-11-01

Full Text Available A small amount of homopolymer poly(vinyl acetate (PVAc is used to compatibilize the biodegradable blends of poly(propylene carbonate (PPC and poly(lactic acid (PLA. Scanning electron microscopy (SEM and differential scanning calorimetry (DSC results show that PVAc is selectively localized in the PLA phase and at the interface between PPC and PLA phases. As a result, these interface-localized PVAc layers act as not only a compatibilizer to improve the phase dispersion significantly but also a bridge to increase the interfacial adhesion between PPC and PLA phases dramatically. Both of them are believed to be responsible for the enhancement in mechanical properties. This work provides a simple avenue to fabricate eco-friendly PPC/PLA blends with high performance, and in some cases, reducing the demand for petroleumbased plastics such as polypropylene.

Preparation and characterization of polysaccharides/PVA blend nanofibrous membranes by electrospinning method.

Science.gov (United States)

Santos, Carla; Silva, Carla J; Büttel, Zsófia; Guimarães, Rodrigo; Pereira, Sara B; Tamagnini, Paula; Zille, Andrea

2014-01-01

A series of polyvinyl alcohol (PVA), PVA/chitosan (CS) and PVA/cyanobacterial extracellular polymeric substances (EPS) blended nanofibrous membranes were produced by electrospinning using a microfiltration poly(vinylidene fluoride) (PVDF) basal membrane, for potential applications in water filtration. Nanofibres were obtained from solutions of 20% (w/w) PVA with 1% (w/w) CS or EPS, using a weight ratio of 60/40. Blended nanofibres have shown a smooth morphology, no beads formation and diameters between 50 and 130 nm. Thermo-mechanical analysis demonstrated that there were inter and/or intramolecular hydrogen bonds between the molecules of PVA/CS and PVA/EPS in the blends. The electrospun blended PVA/EPS membrane showed better tensile mechanical properties when compared with PVA and PVA/CS, and resisted more against disintegration in the temperature range between 10 and 50 °C. Finally, the blended membranes have shown an increase in chromium binding capacity of 5%. This is the first successful report of a blended membrane of electrospinned cyanobacterial polysaccharide with PVA. Copyright © 2013 Elsevier Ltd. All rights reserved.

Study of Biodegradability and Mechanical Properties of Polyvinyl Alcohol (PVA Reinforced Celloluse Nanofiber (CNF

Directory of Open Access Journals (Sweden)

shobo salehpour

2018-02-01

Full Text Available The aim of this study was to improve the properties of polyvinyl alcohol (PVA by using cellulose nanofibers (CNF as a reinforcement. In order to improve the compatibility and miscibility with PVA matrix, freeze drying method was applied. The nanocomposites based on PVA with values 5, 10, 20 and 30wt% of CNF were prepared by freeze-drying and the effect of CNF addition on the mechanical and dynamical mechanical properties, moisture sorption, barrier and biodegradability of the nanocomposites was studied. The tensile strength and elastic modulus of PVA films were improved by the addition of CNF. The nanocomposite with 10wt% nano-fibers had the highest tensile strength and lowest modulus of elasticity and the elongation at break. The results indicated that the storage modulus (E′ of PVA was considerably improved with the introduction of CNF into - polymer matrix. The water vapor permeability decreased from 7.31 to 2.1×10-7 g/m. h. Pa as the CNF percentage increased from 0 to 30%. Also the presence of cellulose nanofibers improved moisture sorption of polyvinyl alcohol. The weight loss of PVA films increased 60% with addition of 30wt% CNF after 90 days of exposure in soil

Poly(vinyl alcohol)/cellulose nanofibril hybrid aerogels with an aligned microtubular porous structure and their composites with polydimethylsiloxane

Science.gov (United States)

Tianliang Zhai; Qifeng Zheng; Zhiyong Cai; Lih-Sheng Turng; Hesheng Xia; Shaoqin Gong

2015-01-01

Superhydrophobic poly(vinyl alcohol) (PVA)/ cellulose nanofibril (CNF) aerogels with a unidirectionally aligned microtubular porous structure were prepared using a unidirectional freeze-drying process, followed by the thermal chemical vapor deposition of methyltrichlorosilane. The silanized aerogels were characterized using various techniques including scanning...

Development and blood compatibility assessment of electrospun polyvinyl alcohol blended with metallocene polyethylene and plectranthus amboinicus (PVA/mPE/PA) for bone tissue engineering.

Science.gov (United States)

Qi, Jie; Zhang, Huang; Wang, Yingzhou; Mani, Mohan Prasath; Jaganathan, Saravana Kumar

2018-01-01

Currently, the design of extracellular matrix (ECM) with nanoscale properties in bone tissue engineering is challenging. For bone tissue engineering, the ECM must have certain properties such as being nontoxic, highly porous, and should not cause foreign body reactions. In this study, the hybrid scaffold based on polyvinyl alcohol (PVA) blended with metallocene polyethylene (mPE) and plectranthus amboinicus (PA) was fabricated for bone tissue engineering via electrospinning. The fabricated hybrid nanocomposites were characterized by scanning electron microscopy (SEM), Fourier transform and infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), contact angle measurement, and atomic force microscopy (AFM). Furthermore, activated partial thromboplastin time (APTT), prothrombin time (PT), and hemolytic assays were used to investigate the blood compatibility of the prepared hybrid nanocomposites. The prepared hybrid nanocomposites showed reduced fiber diameter (238±45 nm) and also increased porosity (87%) with decreased pore diameter (340±86 nm) compared with pure PVA. The interactions between PVA, mPE, and PA were identified by the formation of the additional peaks as revealed in FTIR. Furthermore, the prepared hybrid nanocomposites showed a decreased contact angle of 51°±1.32° indicating a hydrophilic nature and exhibited lower thermal stability compared to pristine PVA. Moreover, the mechanical results revealed that the electrospun scaffold showed an improved tensile strength of 3.55±0.29 MPa compared with the pristine PVA (1.8±0.52 MPa). The prepared hybrid nanocomposites showed delayed blood clotting as noted in APTT and PT assays indicating better blood compatibility. Moreover, the hemolysis assay revealed that the hybrid nanocomposites exhibited a low hemolytic index of 0.6% compared with pure PVA, which was 1.6% suggesting the safety of the developed nanocomposite to red blood cells (RBCs). The prepared nanocomposites exhibited better physico

A new nanocomposite polymer electrolyte based on poly(vinyl alcohol) incorporating hypergrafted nano-silica

KAUST Repository

Hu, Xian-Lei

2012-01-01

Solid-state nanocomposite polymer electrolytes based on poly(vinyl alcohol)(PVA) incorporating hyperbranched poly(amine-ester) (HBPAE) grafted nano-silica (denoted as SiO2-g-HBPAE) have been prepared and investigated. Through surface pretreatment of nanoparticles, followed by Michael-addition and a self-condensation process, hyperbranched poly(amine-ester) was directly polymerized from the surface of nano-silica. Then the hypergrafted nanoparticles were added to PVA matrix, and blended with lithium perchlorate via mold casting method to fabricate nanocomposite polymer electrolytes. By introducing hypergrafted nanoparticles, ionic conductivity of solid composite is improved significantly at the testing temperature. Hypergrafted nano-silica may act as solid plasticizer, promoting lithium salt dissociation in the matrix as well as improving segmental motion of matrix. In addition, tensile testing shows that such materials are soft and tough even at room temperature. From the dielectric spectra of nanocomposite polymer electrolyte as the function of temperature, it can be deduced that Arrhenius behavior appears depending on the content of hypergrafted nano-silica and concentration of lithium perchlorate. At a loading of 15 wt% hypergrafted nano-silica and 54 wt% lithium perchlorate, promising ionic conductivities of PVA nanocomposite polymer electrolyte are achieved, about 1.51 × 10 ^-4 S cm^-1 at 25 °C and 1.36 × 10^-3 S cm^-1 at 100 °C. © The Royal Society of Chemistry.

Graft Copolymerization of Styrene from Poly(vinyl alcohol via RAFT Process

Directory of Open Access Journals (Sweden)

Gholam Ali Koohmareh

2011-01-01

Full Text Available Polystyrene, PS, was grafted from poly(vinyl alcohol, PVA, backbone by reversible addition-fragmentation chain transfer (RAFT polymerization. The hydroxyl groups of the PVA were converted into aromatic dithioester RAFT agent and polymerization began in the presence of this agent. The structure of compounds was confirmed by FT-IR and 1HNMR spectroscopy. The graft copolymer was characterized by thermogravimetric analysis (TGA, X-ray diffraction (XRD, and scanning electron microscopy (SEM. Grafted polystyrene chains were cleaved from the PVA backbone by acidic hydrolysis of the PVA-g-PS, and its polydispersity index, PDI, was determined by gel permeation chromatography (GPC showing narrow molecular weight distribution.

Preparation and characterization of bioglass/polyvinyl alcohol composite hydrogel

International Nuclear Information System (INIS)

Xu Hong; Wang Yingjun; Zheng Yudong; Chen Xiaofeng; Ren Li; Wu Gang; Huang Xiaoshan

2007-01-01

In order to form firm active fixation with the adjacent bone, a new kind of bioactive composite hydrogel was prepared with polyvinyl alcohol (PVA) and bioglass (BG) through ultrasonic dispersion, heat-high-pressure and freeze/thawed technique. A digital speckle correlation method (DSCM) was utilized to characterize the mechanical properties of the series of BG/PVA composites. Results showed that at different load pressures, the composite hydrogel displayed different displacement and deformation in the V field. Results also showed that an increase of PVA percentage (15-30 wt%) or of bioglass percentage (2-10 wt%) in composite hydrogel could lead to an increase in the elastic compression modulus. Scanning electron microscope results indicated that bioglass was uniformly dispersed in the BG/PVA composite hydrogel. The BG/PVA composite hydrogel shows a promising prospect as a new bionic cartilage implantation material

Immobilization in polyvinyl alcohol hydrogel enhances yeast storage stability and reusability of recombinant laccase-producing S-cerevisiae

Czech Academy of Sciences Publication Activity Database

Herkommerová, Klára; Zemančíková, Jana; Sychrová, Hana; Antošová, Zuzana

2018-01-01

Roč. 40, č. 2 (2018), s. 405-411 ISSN 0141-5492 R&D Projects: GA TA ČR(CZ) TA01011461 Institutional support: RVO:67985823 Keywords : immobilization * laccase * LentiKats * polyvinyl alcohol hydrogel * reusability * storage stability * yeasts Subject RIV: EI - Biotechnology ; Bionics OBOR OECD: Industrial biotechnology Impact factor: 1.730, year: 2016

Ortho-positronium annihilation parameters in polyvinyl alcohol films with various degrees of polymerization, saponification and crystallinity

International Nuclear Information System (INIS)

Muramatsu, Hisakazu; Matsumoto, Kuniyuki; Minekawa, Sachiko; Yagi, Yukiko; Sasai, Shigenori

2001-01-01

Positron annihilation lifetime (PAL) spectroscopy has been applied to polyvinyl alcohol (PVA) films prepared with commercially available PVA or from polyvinyl acetate (PVac). The variation of lifetimes of ortho-positronium (o-Ps) formed in the films was investigated as a function of the degrees of polymerization, saponification, or crystallinity. For the fully saponificated samples, no dependence was found to exist on the degrees of polymerization or of crystallinity. For the partially saponificated samples, however, the dependence of the o-Ps lifetime on the degree of saponification was clearly observed, and this is explained by both the formation of hydrogen bonds among the polymer chains and the existence of acetyl group strongly inhibiting the hydrogen-bond formation due to steric hindrance. (orig.)

Radiation modified sago-blends and its potential for biodegradable packaging materials

International Nuclear Information System (INIS)

Zulkafli Ghazali; Sarada Idris; Khairul Zaman Mohd Dahlan

2002-01-01

As a result of rapid population and economic growth, many countries are facing environmental problems created from plastic consumption and those related to garbage disposal. One of the items that is contributing further to this problem would be the foams and plastic wrappers used in packaging. The development of biodegradable packaging material such as foam and film would thus be a step forward in the right direction for the aforementioned industry. This paper highlights work at BTPS on the development of sago blends as alternative biodegradable packaging materials. A study was undertaken to investigate the effect of formulation, mixing temperature and irradiation dosage on expansion of sago starch-polyvinyl alcohol (PVA) and sago-polyvinyl pyrrolidone (PVP) blends based foam. In the beginning foams produced from irradiated hydrogels were achieved by steam expansion in a microwave oven. Some follow-up work using extrusion was also carried out. In the development of starch-based plastic film, the effect of different composition and different irradiation dosage were studied to evaluate films with good tensile properties, elongation, gas permeability and water vapor transmission rate and also the biodegradability of the film using soil burial test. (Author)

Influences of ignition improver additive on ternary (diesel-biodiesel-higher alcohol) blends thermal stability and diesel engine performance

International Nuclear Information System (INIS)

Imdadul, H.K.; Masjuki, H.H.; Kalam, M.A.; Zulkifli, N.W.M.; Alabdulkarem, Abdullah; Rashed, M.M.; Ashraful, A.M.

2016-01-01

Highlights: • Ignition improver additives makes the biodiesel-alcohol blends more thermally stable. • Density and cetane number improved significantly with EHN mixing. • BP and BSFC improved by adding ignition improver additives. • Nitric oxides and smoke of the EHN treated blends decreased. • CO and HC increased slightly with EHN addition. - Abstract: Pentanol is a long chain alcohol produced from renewable sources and considered as a promising biofuel as a blending component with diesel or biodiesel blends. However, the lower cetane number of alcohols is a limitation, and it is important to increase the overall cetane number of biodiesel fuel blends for efficient combustion and lower emission. In this consideration, ignition improver additive 2-ethylhexyl nitrate (EHN) were used at a proportion of 1000 and 2000 ppm to diesel-biodiesel-pentanol blends. Experiments were conducted in a single cylinder; water-cooled DI diesel engine operated at full throttle and varying speed condition. The thermal stability of the modified ternary fuel blends was evaluated through thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) analysis, and the physic-chemical properties of the fuel as well as engine characteristics were studied and compared. The addition of EHN to ternary fuel blends enhanced the cetane number significantly without any significant adverse effect on the other properties. TGA and DSC analysis reported about the improvement of thermal characteristics of the modified blends. It was found that, implementing ignition improver make the diesel-biodiesel-alcohol blends more thermally stable. Also, the brake specific fuel consumption (BSFC), nitric oxides (NO) and smoke emission reduced remarkably with the addition of EHN. Introducing EHN to diesel-biodiesel-alcohol blends increased the cetane number, shorten the ignition delay by increasing the diffusion rate and improve combustion. Hence, the NO and BSFC reduced while, carbon

Optical and electronic properties of polyvinyl alcohol doped with pairs of mixed valence metal ions

International Nuclear Information System (INIS)

Bulinski, Mircea; Kuncser, Victor; Plapcianu, Carmen; Krautwald, Stefan; Franke, Hilmar; Rotaru, P; Filoti, George

2004-01-01

The electronic mechanisms induced by the UV exposure of thin films of polyvinyl alcohol doped with pairs of mixed valence metal ions were studied in relation to their optical behaviour by Moessbauer spectroscopy and optical absorption. The results obtained definitely point to the role of each element from the pair in the electronic mechanism involved, with influence on the optical properties regarding applications in real-time holography and integrated optics

Characterization of proton conducting blend polymer electrolyte using PVA-PAN doped with NH{sub 4}SCN

Energy Technology Data Exchange (ETDEWEB)

Premalatha, M. [PG & Research Department of Physics, N.M.S.S.Vellaichamy Nadar College, Madurai-625 019 (India); Materials Research Center, Coimbatore-641 045 (India); Mathavan, T., E-mail: tjmathavan@gmail.com, E-mail: kingslin.genova20@gmail.com [PG & Research Department of Physics, N.M.S.S.Vellaichamy Nadar College, Madurai-625 019 (India); Selvasekarapandian, S. [Materials Research Center, Coimbatore-641 045 (India); Genova, F. Kingslin Mary, E-mail: tjmathavan@gmail.com, E-mail: kingslin.genova20@gmail.com; Umamaheswari, R. [Department of physics, S.F.R College for Women, Sivakasi-626 128 (India)

2016-05-23

Polymer electrolytes with proton conductivity based on blend polymer using polyvinyl alcohol (PVA) and poly acrylo nitrile (PAN) doped with ammonium thiocyanate have been prepared by solution casting method using DMF as solvent. The complex formation between the blend polymer and the salt has been confirmed by FTIR Spectroscopy. The amorphous nature of the blend polymer electrolytes have been confirmed by XRD analysis. The highest conductivity at 303 K has been found to be 3.25 × 10{sup −3} S cm{sup −1} for 20 mol % NH{sub 4}SCN doped 92.5PVA:7.5PAN system. The increase in conductivity of the doped blend polymer electrolytes with increasing temperature suggests the Arrhenius type thermally activated process. The activation energy is found to be low (0.066 eV) for the highest conductivity sample.

Sorption of water vapor in partially hydrolyzed poly(vinyl acetate)

International Nuclear Information System (INIS)

Spencer, H.G.; Honeycutt, S.C.

1973-01-01

The sorption kinetics of H 2 O and D 2 O in copolymers of partially hydrolyzed poly(vinyl acetate) were studied and compared with the sorption kinetics of vinyl acetate--vinyl alcohol copolymers, and poly(vinyl alcohol). The special measurement problems presented by transient-state sorption studies in water vapor--polymer systems and their effects on the results are discussed

Voltage Effect in Holograms of Polyvinyl Alcohol with FeCl3

Directory of Open Access Journals (Sweden)

Arturo Olivares-Pérez

2014-03-01

Full Text Available We show experimentally that the metallic salt, FeCl3, at different concentrations, provides photosensitivity and conductivity characteristics with poly(vinyl alcohol material. The holographic recording in this photosensitive material was made in real time. The effect of applied voltage on holographic diffraction gratings in the recording process and the changes in their diffraction efficiency, depending on their composition, are shown. In addition, we describe the photo-mechanism, physicochemical processes, and water condensations involved in changes of the formation of images due to applied voltage. The results suggest that polymers doped with metallic salts may have potential as inexpensive photosensitive materials that are easy to work under normal laboratory condition.

Preparation of poly(vinyl alcohol)/kaolinite nanocomposites via in situ polymerization

International Nuclear Information System (INIS)

Jia Xin; Li Yanfeng; Zhang Bo; Cheng Qiong; Zhang Shujiang

2008-01-01

Poly(vinyl alcohol)/kaolinite intercalated nanocomposites (Kao-PVA) were prepared via in situ intercalation radical polymerization. Vinyl acetate (VAc) was intercalated into kaolinite by a displacement method using dimethyl sulfoxide/kaolinite (Kao-DMSO) as the intermediate. Then, PVAc/kaolinite (Kao-PVAc) was obtained via radical polymerization with benzoyl peroxide (BPO) as initiator. Last, PVAc/kaolinite was saponified via direct-hydrolysis with NaOH solution in order to obtain PVA/kaolinite nanocomposites, which was characterized by Fourier-Transformation spectroscopy (FTIR), wide X-ray diffraction (WXRD) and transmission electron microscopy (TEM). Their differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) results of the obtained PVA/kaolinite suggested that the thermal properties had an obvious improvement

Dancing on coke: smuggling cocaine dispersed in polyvinyl alcohol.

Science.gov (United States)

van Nuijs, Alexander L N; Maudens, Kristof E; Lambert, Willy E; Van Calenbergh, Serge; Risseeuw, Martijn D P; Van hee, Paul; Covaci, Adrian; Neels, Hugo

2012-01-01

Recent trends suggest that cocaine smugglers have become more and more inventive to avoid seizures of large amounts of cocaine transported between countries. We report a case of a mail parcel containing a dance pad which was seized at the Customs Department of Brussels Airport, Belgium. After investigation, the inside of the dance pad was found to contain a thick polymer, which tested positive for cocaine. Analysis was performed using a routine colorimetric swipe test, gas chromatography coupled with mass spectrometry and nuclear magnetic resonance spectroscopy. The polymer was identified as polyvinyl alcohol (PVA) and contained 18% cocaine, corresponding to a street value of € 20,000. Laboratory experiments showed that cocaine could be easily extracted from the PVA matrix. This case report reveals a new smuggling technique for the transportation of large amounts of cocaine from one country to another. © 2011 American Academy of Forensic Sciences.

Microwave Absorbent Packaging Material from Composites Chitosan-Polyvinyl Alcohol Polymer

Directory of Open Access Journals (Sweden)

Bambang - Riyanto

2014-11-01

Full Text Available Microwave absorbent packaging materials currently tend to biomaterial. Chitosan is a dielectric biomaterial with polycationic properties. The aim of this study was to analyze characteristics of microwave absorbing packaging material made from composite chitosan-polyvinyl alcohol (PVA polymer. The ability of the packaging material to absorb microwave was determined by reflection loss measurement. Formed packaging prototype resembles as a thin transparent yellowish plastic with thickness (0.11-0.22 mm and the tensile strength (106.33±2.82-143.00±2.59 kPa. SEM analysis showed homogenous structure characterized by interaction between chitosan and PVA. Optimum absorption value was obtained from chitosan concentration of 1%, with average value of reflection loss was (-31.9289±4.0094 dB.Keywords: chitosan, material packaging, microwave, reflection loss

Microwave Absorbent Packaging Material from Composites Chitosan-Polyvinyl Alcohol Polymer

Directory of Open Access Journals (Sweden)

Bambang - Riyanto

2015-07-01

Full Text Available Microwave absorbent packaging materials currently tend to biomaterial. Chitosan is a dielectric biomaterial with polycationic properties. The aim of this study was to analyze characteristics of microwave absorbing packaging material made from composite chitosan-polyvinyl alcohol (PVA polymer. The ability of the packaging material to absorb microwave was determined by reflection loss measurement. Formed packaging prototype resembles as a thin transparent yellowish plastic with thickness (0.11-0.22 mm and the tensile strength (106.33±2.82-143.00±2.59 kPa. SEM analysis showed homogenous structure characterized by interaction between chitosan and PVA. Optimum absorption value was obtained from chitosan concentration of 1%, with average value of reflection loss was (-31.9289±4.0094 dB.Keywords: chitosan, material packaging, microwave, reflection loss

A photo-crosslinked poly(vinyl alcohol) hydrogel growth factor release vehicle for wound healing applications

OpenAIRE

Bourke, Sharon L.; Al-Khalili, Mohammad; Briggs, Tonye; Michniak, Bozena B.; Kohn, Joachim; Poole-Warren, Laura A.

2003-01-01

The objective of this study was to develop and evaluate a hydrogel vehicle for sustained release of growth factors for wound healing applications. Hydrogels were fabricated using ultraviolet photo-crosslinking of acrylamide-functionalized nondegradable poly(vinyl alcohol) (PVA). Protein permeability was initially assessed using trypsin inhibitor (TI), a 21 000 MW model protein drug. TI permeability was altered by changing the solids content of the gel and by adding hydrophilic PVA fillers. As...

Radiation crosslinking of starch/water-soluble polymer blends for hydrogel

International Nuclear Information System (INIS)

Hashim, K.; Mohid, N.; Bahari, K.; Dahlan, K.Z.

2000-01-01

Water-soluble polymers such as PVP(polyvinyl pyrrolidone) and PVA(polyvinyl alcohol), in aqueous solution can form hydrogel easily upon gamma or electron beam irradiation. The properties of hydrogels, particularly for wound dressing application, can be further improved by adding sago starch to the blend. Results show improved gel strength and elongation properties of the hydrogel with increasing sago concentration. It was found that the PVA/sago hydrogel gives better gel strength and elongation than the PVP/sago hydrogel. The tackiness property of the PVA/sago hydrogel increased with increase amount of sago starch added. In case of PVP/sago hydrogel, the tackiness property shows significant increase with increasing amount of sago except for the 5%PVP composition. The swelling properties of PVP/sago and PVA/sago hydrogel decreased with increasing amount of sago but the crosslink density of the hydrogels also reduced. (author)

Radiation crosslinking of starch/water-soluble polymer blends for hydrogel

Energy Technology Data Exchange (ETDEWEB)

Hashim, K.; Mohid, N.; Bahari, K.; Dahlan, K.Z. [Radiation Processing Technology Division, Malaysian Institute Nuclear Technology Research Malaysia (MINT), Bangi, 43000 Kajang (Malaysia)

2000-03-01

Water-soluble polymers such as PVP(polyvinyl pyrrolidone) and PVA(polyvinyl alcohol), in aqueous solution can form hydrogel easily upon gamma or electron beam irradiation. The properties of hydrogels, particularly for wound dressing application, can be further improved by adding sago starch to the blend. Results show improved gel strength and elongation properties of the hydrogel with increasing sago concentration. It was found that the PVA/sago hydrogel gives better gel strength and elongation than the PVP/sago hydrogel. The tackiness property of the PVA/sago hydrogel increased with increase amount of sago starch added. In case of PVP/sago hydrogel, the tackiness property shows significant increase with increasing amount of sago except for the 5%PVP composition. The swelling properties of PVP/sago and PVA/sago hydrogel decreased with increasing amount of sago but the crosslink density of the hydrogels also reduced. (author)

Thermal stability of polyvinyl alcohol/nanocrystalline cellulose composites.

Science.gov (United States)

Voronova, Marina I; Surov, Oleg V; Guseinov, Sabir S; Barannikov, Vladimir P; Zakharov, Anatoly G

2015-10-05

Thermal stability of polyvinyl alcohol/cellulose nanocrystals (PVA/CNCs) composites prepared with solution casting technique was studied. The PVA/CNCs composites were characterized by Fourier transform infrared spectrometry, X-ray diffraction, differential scanning calorimeter (DSC) and thermogravimetric (TG) analysis. Due to the presence of CNCs nanoparticles, thermal degradation of the composites occurs at much higher temperatures compared to that of the neat PVA. Thermal stability of the PVA/CNCs composites is maximally enhanced with CNCs content of 8-12 wt%. Some thermal degradation products of the PVA/CNCs composites were identified by mass spectrometric analysis. TG measurements with synchronous recording of mass spectra revealed that the thermal degradation of both CNCs and PVA in the composites with CNCs content of 8-12 wt% occurs simultaneously at a much higher temperature than that of CNCs or the neat PVA. However, with increasing CNCs content more than 12 wt% the thermal stability of the composites decreases. In this case, the degradation of CNCs comes first followed by the degradation of PVA. Copyright © 2015 Elsevier Ltd. All rights reserved.

Long Term Performance Study of a Direct Methanol Fuel Cell Fed with Alcohol Blends

OpenAIRE

Teresa J. Leo; Miguel A. Raso; Emilio Navarro; Eleuterio Mora

2013-01-01

The use of alcohol blends in direct alcohol fuel cells may be a more environmentally friendly and less toxic alternative to the use of methanol alone in direct methanol fuel cells. This paper assesses the behaviour of a direct methanol fuel cell fed with aqueous methanol, aqueous ethanol and aqueous methanol/ethanol blends in a long term experimental study followed by modelling of polarization curves. Fuel cell performance is seen to decrease as the ethanol content rises, and subsequent opera...

Mechanical and chemical properties of polyvinyl alcohol modified cement mortar with silica fume used as matrix including radioactive waste

International Nuclear Information System (INIS)

Dakroury, A. M.

2007-01-01

This paper discussed the mechanical and chemical properties of polyvinyl alcohol - modified cement mortar with silica fume to assess the safety for disposal of radioactive waste. The modified cement mortars containing polyvinyl alcohol (PVA) in the presence of 10 % silica fume (SF) .The chemical reaction between polymer and cement - hydrated product were investigated by the Infrared Spectral Technology, Differential Thermal Analysis and X-ray diffraction. The leaching of 137Cs from a waste composite into a surrounding fluid has been studied .The results shown that PVA increases the strength and decreases the porosity. The increase in strength duo to the interaction of PVA with cement , may be forming some new compound that fill the pores or improve the bond between the cement . The pozzolanic reaction of the SF increases the calcium silicate hydrates in the hardening matrix composites. There is distinct change in the refinement of the pore structure in cement composites giving fewer capillary pores and more of the finer gel pores

Effect of UV irradiation on optical, mechanical and microstructural properties of PVA/NaAlg blends

Science.gov (United States)

Sheela, T.; Bhajantri, R. F.; Ravindrachary, V.; Rathod, Sunil G.; Pujari, P. K.; Poojary, Boja; Somashekar, R.

2014-10-01

Poly(vinyl alcohol) (PVA)/Sodium alginate (NaAlg) blend films with 60:40 wt% were prepared by solution casting method and subjected to UV irradiation for different intervals of time. The optical, mechanical and morphological properties of the blend films were modified after UV irradiation. The FTIR and FT-Raman results show the chemical interaction between PVA and NaAlg. The UV-vis absorption peak at 278 nm shifts slightly towards longer wavelength and the absorption increases with irradiation time, indicate the increase in crosslinking network. The XRD results show an increase in amorphous nature with increase in UV irradiation time. The DSC/TGA results show a single glass transition temperature (Tg), which confirm that the blends are completely miscible and thermally stable up to 250 °C. The Young's modulus, tensile strength and stiffness of the blend films increase with increase in UV irradiation time. The SEM images confirm that the surface of 48 h UV irradiated PVA:NaAlg blend is more photo-resistant than unirradiated blend.

Polyvinyl alcohol (PVA)-cellulose nanofibril (CNF)-multiwalled carbon nanotube (MWCNT) hybrid organic aerogels with superior mechanical properties

Science.gov (United States)

Qifeng Zheng; Alireza Javadi; Ronald Sabo; Zhiyong Cai; Shaoqin Gong

2013-01-01

Polyvinyl alcohol (PVA)–cellulose nanofibril (CNF)–multiwalled carbon nanotube (MWCNT) hybrid organic aerogels were prepared using an environmentally friendly freeze-drying process with renewable materials. The material properties of these “green” hybrid aerogels were characterized extensively using various techniques. It was found that adding a small amount of CNFs...

Polyvinyl-alcohol-based magnetic beads for rapid and efficient separation of specific or unspecific nucleic acid sequences

International Nuclear Information System (INIS)

Oster, J.; Parker, Jeffrey; Brassard, Lothar

2001-01-01

The versatile application of polyvinyl-alcohol-based magnetic M-PVA beads is demonstrated in the separation of genomic DNA, sequence specific nucleic acid purification, and binding of bacteria for subsequent DNA extraction and detection. It is shown that nucleic acids can be obtained in high yield and purity using M-PVA beads, making sample preparation efficient, fast and highly adaptable for automation processes

Fabrication and Characterization of Electrospun Wool Keratin/Poly(vinyl alcohol Blend Nanofibers

Directory of Open Access Journals (Sweden)

Shuai Li

2014-01-01

Full Text Available Wool keratin/poly(vinyl alcohol (PVA blend nanofibers were fabricated using the electrospinning method in formic acid solutions with different weight ratios of keratin to PVA. The resultant blend nanofibers were characterized by scanning electron microscopy (SEM, Fourier transform infrared (FTIR, X-ray diffraction (XRD, thermal gravimetric analysis (TGA, and tensile test. SEM images showed that the diameter of the blend nanofibers was affected by the content of keratin in blend solution. FTIR and XRD analyses data demonstrated that there were good interactions between keratin and PVA in the blended nanofibers caused by possibly hydrogen bonds. The TGA study revealed that the thermal stability of the blend nanofibers was between those of keratin and PVA. Tensile test indicated that the addition of PVA was able to improve the mechanical properties of the electrospun nanofibers.

In vitro and ex vivo hemocompatibility of off-the-shelf modified poly(vinyl alcohol) vascular grafts

OpenAIRE

Cutiongco, Marie Francene A.; Anderson, Deirdre E. J.; Hinds, Monica T.; Yim, Evelyn K. F.

2015-01-01

Synthetic small diameter vascular grafts with mechanical properties of native arteries, resistance to thrombosis and capacity to stimulate in situ endothelialization are an unmet clinical need. Poly(vinyl alcohol) hydrogel (PVA) is an excellent candidate as a vascular graft due to its tunable mechanical properties. However, the hydrophilicity and bio-inertness of PVA prevents endothelialization in vivo. We hypothesize that the modification of PVA with biomolecules and topographies creates a h...

Method of cross-linking polyvinyl alcohol and other water soluble resins

Science.gov (United States)

Phillipp, W. H.; May, C. E.; Hsu, L. C.; Sheibley, D. W. (Inventor)

1980-01-01

A self supporting sheet structure comprising a water soluble, noncrosslinked polymer such as polyvinyl alcohol which is capable of being crosslinked by reaction with hydrogen atom radicals and hydroxyl molecule radicals is contacted with an aqueous solution having a pH of less than 8 and containing a dissolved salt in an amount sufficient to prevent substantial dissolution of the noncrosslinked polymer in the aqueous solution. The aqueous solution is then irradiated with ionizing radiation to form hydrogen atom radicals and hydroxyl molecule radicals and the irradiation is continued for a time sufficient to effect crosslinking of the water soluble polymer to produce a water insoluble polymer sheet structure. The method has particular application in the production of battery separators and electrode envelopes for alkaline batteries.

Composite films based on biorelated agro-industrial waste and poly(vinyl alcohol). Preparation and mechanical properties characterization.

Science.gov (United States)

Chiellini, E; Cinelli, P; Imam, S H; Mao, L

2001-01-01

As a part of an ongoing project on the production of composite materials based on poly(vinyl alcohol) (PVA) and polymeric materials from renewable resources, the present paper reports on the incorporation of agricultural waste materials as organic fillers in a film matrix based on PVA as continuous phase. In this study lignocellulosic fibers byproducts, derived from sugar cane (SC) and apple (AP) and orange (OR) fruit juice extraction, were cast from PVA aqueous solutions. The effect of fiber type and composition on the relative properties of cast films was evaluated and compared. OR resulted to be suitable for blending in higher amounts by weight than SC and AP. Glycerol and urea were added as plasticizing agents and were observed to be effective in giving flexible films. Additionally, cornstarch was added to further increase the composition of polymers from renewable resources in cost-effective and ecoefficient composite film formulations. The prepared films resulted sensitive to moisture and water. To reduce water sensitivity, hexamethoxymethylmelamine (HMMM) was tested as a cross-linking agent for the present composite formulations. Cross-linked films exhibited significant improvement in water-resistance that can be taken as a tuneable structural feature for customized applications. The mechanical properties of the prepared composite films (elongation at break, tensile strength, Young modulus) were found to be dependent upon the nature and content of the filler and on environmental conditions.

Utilization of Cellulose from Pineapple Leaf Fibers as Nanofiller in Polyvinyl Alcohol-Based Film

Directory of Open Access Journals (Sweden)

Kendri Wahyuningsih

2016-08-01

Full Text Available Cellulose from pineapple leaf fibers as one of the natural polymer which has biodegradable property in a nanometer’s scale, can be formed as a filler in composite of Poly(vinyl Alcohol/PVA is expected to increase the physical, thermal, and barrier properties of composite films similar to conventional plastic. The aim of this study was to examine the effect of fibrillation of cellulose fibers from pineapple leaf fibers using a combined technique of chemical-mechanical treatments, to investigate the reinforcing effect of concentration of nanocellulose fibrils in the polyvinyl alcohol (PVA matrix on physical properties, thermal properties, water vapor transmission rate, light transmittance and morphological with and without addition of glycerol. Nanocellulose was made from cellulose of pineapple leaf fiber using wet milling (Ultra Fine Grinder. The composite film production was carried out by using casting solution method by mixing PVA solution with nanocellulose (10-50% and glycerol (0-1%. The characterization of film covered physical properties (thickness, moisture content and density, thermal properties, permeability (WVTR, light transmittance, morphology, and crystallinity. Nanocellulose from pineapple leaf fibers was produced by Ultra Fine Grinder shows that the size reduction process was accurate. Nanocellulose addition on PVA composite film was affected to increasing the physical, thermal, and barrier properties. Meanwhile, decreasing the percentage of composite film transmittance, thus the transparency decrease (opaque. Water vapor transmission rate (WVTR the film was increased with increasing glycerol concentration, but the physical and thermal properties was decreased.

Long Term Performance Study of a Direct Methanol Fuel Cell Fed with Alcohol Blends

Directory of Open Access Journals (Sweden)

Eleuterio Mora

2013-01-01

Full Text Available The use of alcohol blends in direct alcohol fuel cells may be a more environmentally friendly and less toxic alternative to the use of methanol alone in direct methanol fuel cells. This paper assesses the behaviour of a direct methanol fuel cell fed with aqueous methanol, aqueous ethanol and aqueous methanol/ethanol blends in a long term experimental study followed by modelling of polarization curves. Fuel cell performance is seen to decrease as the ethanol content rises, and subsequent operation with aqueous methanol only partly reverts this loss of performance. It seems that the difference in the oxidation rate of these alcohols may not be the only factor affecting fuel cell performance.

Preparation and properties of polyvinyl alcohol microspheres

International Nuclear Information System (INIS)

Campbell, J.H.; Grens, J.Z.; Poco, J.F.; Ives, B.H.

1986-06-01

Polyvinyl alcohol (PVA) microspheres, having a size range of ∼150- to 250-μm diameter with 1- to 5-μm wall thickness, have been fabricated using a solution droplet technique. The spheres were developed for possible use on the Lawrence Livermore National Laboratory (LLNL) Inertial Confinement Fusion (ICF) Program. PVA, a polymer chosen based on earlier survey work carried out at KMS Fusion, Inc., has good strength, low hydrogen permeability, is optically transparent, and water soluble. The latter property makes it safe and easy to use in our droplet generator system. A unique dual-orifice droplet generator was used to prepare the spheres. The droplet generator operating conditions and the column processing parameters were chosen using results from our 1-D model calculations as a guide. The polymer microsphere model is an extension of the model we developed to support the glass sphere production. After preparation, the spheres were physically characterized for surface quality, sphericity, wall thickness (and uniformity), and size. We also determined the buckling pressure for both uncoated and CH-coated spheres. Radiation stability to beta decay (from tritium) was evaluated by exposing the spheres to a 7-keV electron beam. The results from these and other physical property measurements are presented in this report

The effect of bacterial cellulose on the shape memory behavior of polyvinyl alcohol nanocomposite hydrogel

Science.gov (United States)

Pirahmadi, Pegah; Kokabi, Mehrdad

2018-01-01

Most research on shape memory polymers has been confined to neat polymers in their dry state, while, some hydrogel networks are known for their shape memory properties. Hydrogels have low glass transition temperatures which are below 100°C depend on the content of water. But they are usually weak and brittle, and not suitable for structural applications due to their low mechanical strengths because of these materials have large amount of water (>50%), so they could not remember original shape perfectly. Bacterial cellulose nanofibers with perfect properties such as high water holding capacity, high crystallinity, high tensile strength and good biocompatibility can dismiss all the drawbacks. In the present study, polyvinyl alcohol/bacterial cellulose nanocomposite hydrogel prepared by repetitive freezing-thawing method. The bacterial cellulose was used as reinforcement to improve the mechanical properties and stimuli response. Differential scanning calorimetry was employed to obtain the glass transition temperature. Nanocomposite morphology was characterized by field-emission scanning electron microscopy and mechanical properties were investigated by standard tensile test. Finally, the effect of bacterial cellulose nanofiber on shape memory behavior of polyvinyl alcohol/bacterial cellulose nanocomposite hydrogel was investigated. It is found that switching temperature of this system is the glass transition temperature of the nano domains formed within the system. The results also show increase of shape recovery, and shape recovery speed due to presence of bacterial cellulose.

Deproteinised natural rubber latex grafted poly(dimethylaminoethyl methacrylate) - poly(vinyl alcohol) blend membranes: Synthesis, properties and application.

Science.gov (United States)

Jayadevan, Janisha; Alex, Rosamma; Gopalakrishnapanicker, Unnikrishnan

2018-02-01

Natural rubber latex was initially deproteinised (DNRL) and then subjected to physicochemical modifications to make high functional membranes for drug delivery applications. Initially, DNRL was prepared by incubating with urea, sodiumdodecylsulphate and acetone followed by centrifugation. The deproteinisation was confirmed by CHN analysis. The DNRL was then chemically modified by grafting (dimethylaminoethyl methacrylate) onto NR particles by using a redox initiator system viz; cumene hydroperoxide/tetraethylenepentamine, followed by dialysis for purification. The grafting was confirmed by dynamic light scattering, Fourier transform infrared spectroscopy and nuclear magnetic resonance spectroscopy. The grafted system was blended with a hydrophilic adhesive polymer PVA and casted into membranes. The membranes after blending showed enhanced mechanical properties with a threshold concentration of PVA. The moisture uptake, swelling and water contact angle experiments indicated an increased hydrophilicity with an increased PVA content in the blend membranes. The grafted DNRL possessed significant antibacterial property which has been found to be retained in the blended form. A notable decrease in cytotoxicity was observed for the modified DNRL membranes than the bare DNRL membranes. The in-vitro drug release studies using rhodamine B as a model drug, confirmed the utility of the prepared membranes to function as a drug delivery matrix. Copyright © 2017 Elsevier B.V. All rights reserved.

Radiation modified sago-blends and its potential for biodegradable packaging materials

Energy Technology Data Exchange (ETDEWEB)

Ghazali, Z.; Idris, S.; Dahlan, K.Z. [Malaysian Institute for Nuclear Technology Research, Bangi, Kajang (Malaysia); Wongsuban, B.; Adzahan, N.M.; Ithnin, L. [Universiti Putra Malaysia, Faculty of Food Science and Biotechnology, Serdang (Malaysia)

2002-03-01

This paper describes work at MINT on the characterisation and development of sago blends as alternative biodegradable packaging materials. A study was undertaken to investigate the effect of formulation, mixing temperature and irradiation dosage on expansion of sago starch-polyvinyl alcohol (PVA) and sago-polyvinyl pyrrolidone (PVP) blends based foam. The foams were produced by microwaving irradiated hydrogels prepared by mixing sago starch with aqueous PVA or PVP. In the development of starch-based plastic, the effect of different composition and different irradiation dosage were studied to evaluate films with good tensile properties, elongation, gas permeability and water vapor transmission rate and also the biodegradability of the film using soil burial test. In another development, irradiation i.e. microwave, electron beam and gamma, has been investigated as a means of degrading the starch granules, which leads to an increase in the amount soluble materials leached. Results showed that irradiation caused an increase in leaching, and a concomitant drastic reduction in swelling volumes of starch granules. It is also showed that the strength of starch gels and viscosity decreased as the levels of irradiation was increased. The degraded starches will be incorporated as an ingredient in the fish cracker and characterized its properties. (author)

Preparation of poly(vinyl alcohol) membranes grafted with N-vinyl imidazole/acrylic acid binary monomers

International Nuclear Information System (INIS)

Ajji, Zaki; Ali, Ali

2006-01-01

Poly(vinyl alcohol) films were grafted with two monomers using gamma radiation, acrylic acid and N-vinyl imidazole. The influence of different parameters on the grafting yield was investigated as: type of solvent and solvent composition, comonomer concentration and composition, addition of mineral acids, and irradiation dose. Water uptake in respect to the grafting yield was also evaluated. The ability of the grafted films to adsorb copper ions was elaborated and discussed for different grafting yields and ph values of the solution. (authors)

Synthesis and characterization of CdxMn1-xS nanoparticles stabilized with poly(vinyl alcohol)

International Nuclear Information System (INIS)

Schatkoski, Vanessa M.; Mansur, Alexandra A.P.; Mansur, Herman S.; Gonzalez, Juan C.

2011-01-01

Colloidal luminescent semiconductor nanocrystals, also known as quantum dots, have attracted considerable attention due to their significant potential application. The doping of nanocrystalline semiconductors with divalent manganese ions results in new optical properties of these semimagnetic semiconductor quantum dots. In this work we report the synthesis and characterization Cd x Mn 1-x S nanoparticles using poly(vinyl alcohol) as stabilizing agent. Different fractions of Cd 2+ /Mn 2+ ions were investigated aiming the production of stable nanoparticles with different photoluminescence properties. (author)

Properties of poly(vinyl alcohol)-borax gel doped with neodymium and praseodymium

International Nuclear Information System (INIS)

Lawrence, Mathias B.; Desa, J.A.E.; Rai, Renu; Aswal, V.K.

2014-01-01

Neodymium and praseodymium ions, singly and in combination, have been doped into a poly(vinyl alcohol)-borax matrix. X-ray diffraction shows structural correlations from 2 to 6 Å and 15 Å, while small angle neutron scattering indicates that the rare-earth ions do not affect the nanoscale structures of the gels. Differential scanning calorimetry shows the glass transition temperature to increase with concentration of Pr in the gel. Excitation in the ultraviolet region leads to luminescent emission in the visible region. Simultaneous absorption in the visible region then leads to luminescent emission in the near infra-red region. The spectral qualities of the emission bands can be varied by choosing appropriate relative ratios of rare-earth species. (author)

Photo-triggered release from liposomes without membrane solubilization, based on binding to poly(vinyl alcohol) carrying a malachite green moiety.

Science.gov (United States)

Uda, Ryoko M; Kato, Yutaka; Takei, Michiko

2016-10-01

When working with liposomes analogous to cell membranes, it is important to develop substrates that can regulate interactions with the liposome surface in response to light. We achieved a photo-triggered release from liposomes by using a copolymer of poly(vinyl alcohol) carrying a malachite green moiety (PVAMG). Although PVAMG is a neutral polymer under dark conditions, it is photoionized upon exposure to UV light, resulting in the formation of a cationic site for binding to liposomes with a negatively charged surface. Under UV irradiation, PVAMG showed effective interaction with liposomes, releasing the encapsulated compound; however, this release was negligible under dark conditions. The poly(vinyl alcohol) moiety of PVAMG played an important role in the photo-triggered release. This release was caused by membrane destabilization without lipid solubilization. We also investigated different aspects of liposome/PVAMG interactions, including PVAMG-induced fusion between the liposomes and the change in the liposome morphologies. Copyright © 2016 Elsevier B.V. All rights reserved.

preparation and properties of immobilized naringinase in polyvinyl alcohol copolymer carrier for debittering of citrus juices

International Nuclear Information System (INIS)

ElBatal, A.L.; Swailam, H.M.H.

2003-01-01

Naringin a bitter compound in citrus can be converted to a nonbiter fom by enzyme hydrolysis. Naringinase from gamma irradiated enhanced Aspergillus nigro-AH3. γ 20 isolate was partoally purified by various methods and the specificacitivty of 6.1 units per mg protein was obtained. The enzyme was immobilized by entrapment in polyvinyl alcohol / polyacrylamide (PVA/PAAm) copolymer hydrogel carrier produced by gamma radiation polymerization. The activity of the immobilized enzyme was elevated with increasing PVA content in the copolymer carrier to reach its maximum value at PVA/PAAm composition ratio of (60.40, v/v%). The yield of immobilization was highest 95% and yield of activity was 91.1%, when 1 mg naringinase enzyme was immobilized in 1 ml of hydrogel matrix. Some enzymatic and compared with those of the solube free enzyme. The optimal pH of the immobilized enzyme was shifted 0.5 pH units to the alkaline side of that of the soluble free enzyme. Also the optimum temperature was shifted from 50 C degree to 60 c degree and the activation energy of reaction (EA) was markedly decreased from 21.52 to 10.74kcal/mol by immobilization. The influence of the diffusion is reflected in the kinetic parameters Km and Vmax. The application of kinetic parameter of the immobilized enzyme optimized with pure naringin solution and bitter orange juice resuled in about 83.2% and 72.0% debittering after 8 h and 12 h incubation during batcheise operation, respectively. The process has operational versatility from the broad pH and temperature optima and affords highest efficiency and stability during application in debittering of bitter orange juice because it is recycled consecutively 14 times before retaining only about 50 % efficiency. These data can be used for future improvements in debittering of citrus fruits products

Effects of electron beam irradiation on properties of corn starch undergone periodate oxidation mechanism blended with polyvinyl alcohol

Science.gov (United States)

Bee, Soo-Tueen; Sin, Lee Tin; Ratnam, C. T.; Yap, Bee-Fen; Rahmat, A. R.

2018-02-01

This work was performed to examine the properties of pristine PVOH and PVOH-starch blends under exposure of different irradiation dosages. The periodate oxidation method was used to produce dialdehyde starch. The application of low dosages of electron beam irradiation (≤10 kGy) has improved the tensile strength by forming crosslinking networks. However, the tensile strength drastically declined when radiated at 30 kGy due to the reduction of available hydroxyl groups inside polymer matrix for intermolecular interaction. Also, the incorporation of corn starch and dialdehyde starch has significantly reduced the melting temperature and enthalpy of melting of PVOH blends due to cessation of the hydrogen bonding between PVOH and starch molecules. The crystallite size for deflection planes (1 0 1), (1 0 1) and (2 0 0) for all PVOH blends was significant reduced when irradiated. The electron beam irradiation has also weakened the hydrophilic characteristic of all PVOH blends as evidenced in infrared and microscopy analysis.

Ionic conductivity studies in crystalline PVA/NaAlg polymer blend electrolyte doped with alkali salt KCl

Science.gov (United States)

Sheela, T.; Bhajantri, R. F.; Ravindrachary, V.; Pujari, P. K.; Rathod, Sunil G.; Naik, Jagadish

2014-04-01

Potassium Chloride (KCl) doped poly(vinyl alcohol) (PVA)/sodium alginate (NaAlg) in 60:40 wt% polymer blend electrolytes were prepared by solution casting method. The complexation of KCl with host PVA/NaAlg blend is confirmed by FTIR and UV-Vis spectra. The XRD studies show that the crystallinity of the prepared blends increases with increase in doping. The dc conductivity increases with increase in dopant concentration. Temperature dependent dc conductivity shows an Arrhenius behavior. The dielectric properties show that both the dielectric constant and dielectric loss increases with increase in KCl doping concentration and decreases with frequency. The cole-cole plots show a decrease in bulk resistance, indicates the increase in ac conductivity, due to increase in charge carrier mobility. The doping of KCl enhances the mechanical properties of PVA/NaAlg, such as Young's modulus, tensile strength, stiffness.

PVA/Polysaccharides Blended Films: Mechanical Properties

Directory of Open Access Journals (Sweden)

Fábio E. F. Silva

2013-01-01

Full Text Available Blends of polyvinyl alcohol (PVA and angico gum (AG and/or cashew gum (CG were used to produce films by casting method. Morphological and mechanical properties of these films were studied and compared to the properties of a commercial collagen membrane of bovine origin (MBO. The films presented thickness varying from 70 to 140 μm (PVA/AG and 140 to 200 μm (PVA/CG. Macroscopic analysis showed that a PVA/CG film was very similar to MBO regarding the color and transparency. The higher values of tensile strength (TS and elastic modulus (EM were observed in the film. On the other hand, PVA/CG and PVA/CG-AG presented the highest value of percentage of elongation (E%. Pearson’s Correlation Analysis revealed a positive correlation between TS and EM and a negative correlation between E% and EM. The PVA/CG film presented mechanical properties very similar to MBO, with the advantage of a higher E% (11.96 than MBO (2.94. The properties of the PVA blended films depended on the polysaccharide added in the blend, as well as the acid used as a catalyst. However, all produced films presented interesting mechanical characteristics which enables several biotechnological applications.

Sliding friction at poly(vinyl alcohol)-modified carbon nanotube interfaces

Science.gov (United States)

Zhang, Xiaohua

2018-01-01

The sliding friction between adjacent carbon nanotubes (CNTs) determines greatly the mechanical property of CNT assembly materials. In order to enhance the intertube friction, polymer molecules are often introduced between CNTs. This paper reveals a new energy dissipation mechanism for the deformed CNT contacts by poly(vinyl alcohol) (PVA). When PVA is introduced into a CNT bundle, most segments of the polymer chain lay on the grooves of adjacent CNTs, while several short segments span over the contact CNTs by inducing a structural deformation on the tubular structure. During the tube sliding, the deformation is recovered and a new one is formed at the next position, contributing to new energy dissipation to prevent the tube sliding. As a result, the friction force can be enhanced by up to eight-fold. This study indicates that a network of transverse polymer chains and longitudinal CNTs is important towards high mechanical properties.

Formation of inorganic nanofibers by heat-treatment of poly(vinyl alcohol-zirconium compound hybrid nanofibers

Directory of Open Access Journals (Sweden)

Nakane K.

2013-01-01

Full Text Available Poly(vinyl alcohol-zirconium compound hybrid nanofibers (precursors were formed by electrospinning employing water as a solvent for the spinning solution. The precursors were converted into oxide (ZrO2, carbide (ZrC or nitride (ZrN nanofibers by heating them in air, Ar or N2 atmospheres. Monoclinic ZrO2 nanofibers with high-specific surface area were obtained by heat-treatment of the precursors in air. ZrC and ZrN nanofibers could be obtained below theoretical temperatures calculated from thermodynamics data.

Studies on nonlocal optical nonlinearity of Sr–CuO–polyvinyl alcohol nanocomposite thin films

International Nuclear Information System (INIS)

Tamgadge, Y.S.; Talwatkar, S.S.; Sunatkari, A.L.; Pahurkar, V.G.; Muley, G.G.

2015-01-01

Thermally induced nonlocal nonlinear optical properties of strontium (Sr) doped CuO-polyvinyl alcohol (PVA) nanocomposite thin films under continuous wave Helium–Neon laser illumination are investigated by single beam Z-scan method. Undoped and Sr doped CuO nanoparticles (NPs) using L-arginine as surface modifying agent have been synthesized by wet chemical method and their thin films with PVA as host matrix have been obtained by spin coating technique. Structure, morphology and purity of prepared CuO NPs and thin films have been studied by X-ray diffraction, high-resolution transmission electron microscopy, field emission scanning electron microscopy and energy dispersive X-ray absorption spectroscopy. Fourier transform infra-red spectrum attests the role of L-arginine as surface modifier and ultraviolet–visible absorption studies reveal that the excitonic absorption wavelengths are blue shifted for strontium doped CuO NPs. Sr doped CuO NPs with average particle size of 7 nm and calculated optical band gap up to 2.54 eV have been reported. All Sr doped CuO–PVA nanocomposite thin films show enhanced nonlinear refraction and absorption best suited for optical limiting applications. Observed effects have been attributed to thermal lensing effect. - Highlights: • Pure and strontium doped CuO–polyvinyl alcohol nanocomposite thin films are prepared. • Z-scan studies of thin films are performed under continuous wave helium–neon laser. • Enhanced values of third order nonlinear optical coefficients are obtained for all films. • Thermally induced self-defocusing and reverse saturable absorption have been discussed.

Studies on nonlocal optical nonlinearity of Sr–CuO–polyvinyl alcohol nanocomposite thin films

Energy Technology Data Exchange (ETDEWEB)

Tamgadge, Y.S. [Department of Physics, Mahatma Fule Arts, Commerce and S C Science Mahavidyalaya, Warud, Dist. Amravati (MS), 444906 (India); Talwatkar, S.S. [Department of Physics, D K Marathe and N G Acharya College, Chembur, Mumbai (MS) 440071 (India); Sunatkari, A.L. [Department of Physics, Siddharth College of Arts, Science and Commerce, Fort, Mumbai (MS) 440001 (India); Pahurkar, V.G. [Department of Physics, Sant Gadge Baba Amravati University, Amravati (MS), 444602 (India); Muley, G.G., E-mail: gajananggm@yahoo.co.in [Department of Physics, Sant Gadge Baba Amravati University, Amravati (MS), 444602 (India)

2015-11-30

Thermally induced nonlocal nonlinear optical properties of strontium (Sr) doped CuO-polyvinyl alcohol (PVA) nanocomposite thin films under continuous wave Helium–Neon laser illumination are investigated by single beam Z-scan method. Undoped and Sr doped CuO nanoparticles (NPs) using L-arginine as surface modifying agent have been synthesized by wet chemical method and their thin films with PVA as host matrix have been obtained by spin coating technique. Structure, morphology and purity of prepared CuO NPs and thin films have been studied by X-ray diffraction, high-resolution transmission electron microscopy, field emission scanning electron microscopy and energy dispersive X-ray absorption spectroscopy. Fourier transform infra-red spectrum attests the role of L-arginine as surface modifier and ultraviolet–visible absorption studies reveal that the excitonic absorption wavelengths are blue shifted for strontium doped CuO NPs. Sr doped CuO NPs with average particle size of 7 nm and calculated optical band gap up to 2.54 eV have been reported. All Sr doped CuO–PVA nanocomposite thin films show enhanced nonlinear refraction and absorption best suited for optical limiting applications. Observed effects have been attributed to thermal lensing effect. - Highlights: • Pure and strontium doped CuO–polyvinyl alcohol nanocomposite thin films are prepared. • Z-scan studies of thin films are performed under continuous wave helium–neon laser. • Enhanced values of third order nonlinear optical coefficients are obtained for all films. • Thermally induced self-defocusing and reverse saturable absorption have been discussed.

Synthesis of Novel (Polymer Blend-Titanium Carbide Nanocomposites and Studying their Characterizations for Piezoelectric Applications

Directory of Open Access Journals (Sweden)

Ahmed Hashima

2018-05-01

Full Text Available Piezoelectric nanocomposites are very important for many applications as a pressure sensors. Fabrication of (polyvinyl alcohol - polyvinyl pyrrolidinone -titanium carbide nanocompos- ites and study their structural, electrical, dielectric and optical properties have been in- vestigated. The effect of adding the TiC nanoparticles on structural, electrical, dielectric and optical properties of polymeric blend has been studied. The results showed that the electrical conductivity of (PVA-PVP-TiC nanocomposites is increasing with the increase of TiC nanoparticles concentrations at room temperature. The FTIR analysis showed there is no interactions between (PVA- PVP polymer blend and TiC nanoparticles. The dielectric studies showed the dielectric constant and dielectric loss of nanocomposites increase with the increase of TiC nanoparticles concentrations and they decrease as frequency increased. The A.C electrical conductivity increases with the increase of TiC nanoparticles concentra- tions and frequency. The results of optical properties showed that the optical absorbance of (PVA- PVP polymer blend increases with the increase of TiC nanoparticles concentrations. The optical constants change with increase in TiC nanoparticles concentrations. The piezo- electric application results of (PVA-PVP-TiC nanocomposites showed that the electrical resistance of (PVA-PVP-TiC nanocomposites decreases with an increase of the pressure which make it is suitable for piezoelectric applications or pressure sensors.

Incorporation of a Cationic Conjugated Polyelectrolyte CPE within an Aqueous Poly(vinyl alcohol) Sol

DEFF Research Database (Denmark)

Knaapila, Matti; Stewart, Beverly; Costa, Telma

2016-01-01

We report on a multiscale polymer-within-polymer structure of the cationic conjugated polyelectrolyte poly{[9,9-bis(6-N,N,N-trimethylammonium)hexyl]fluorene phenylene} (HTMAPFP) in aqueous poly(vinyl alcohol).(PVA) sol. Molecular dynamics simulations and small-angle neutron scattering (SANS) data...... show that HTMA-PFP forms aggregates in water but becomes entangled by PVA (with a 1:1 molar ratio of HTMA-PFP to PVA) and eventually immersed in PVA clusters (with the ratio 1:4). This is attributed to the hydrophobic hydrophilic balance. Contrast variation data with regular and deuterated PVA support...

Modification of polyvinyl alcohol surface properties by ion implantation

Energy Technology Data Exchange (ETDEWEB)

Pukhova, I.V., E-mail: ivpuhova@mail.ru [National Research Tomsk State University, 36 Lenin Ave, Tomsk 634050 (Russian Federation); Institute of High Current Electronics, 2/3 Akademichesky Ave, Tomsk 634055 (Russian Federation); Kurzina, I.A. [National Research Tomsk State University, 36 Lenin Ave, Tomsk 634050 (Russian Federation); Savkin, K.P. [Institute of High Current Electronics, 2/3 Akademichesky Ave, Tomsk 634055 (Russian Federation); Laput, O.A. [National Research Tomsk Polytechnic University, 30 Lenin Ave, Tomsk 634050 (Russian Federation); Oks, E.M. [Institute of High Current Electronics, 2/3 Akademichesky Ave, Tomsk 634055 (Russian Federation)

2017-05-15

We describe our investigations of the surface physicochemical properties of polyvinyl alcohol modified by silver, argon and carbon ion implantation to doses of 1 × 10{sup 14}, 1 × 10{sup 15} and 1 × 10{sup 16} ion/cm{sup 2} and energies of 20 keV (for C and Ar) and 40 keV (for Ag). Infrared spectroscopy (IRS) indicates that destructive processes accompanied by chemical bond (−C=O) generation are induced by implantation, and X-ray photoelectron spectroscopy (XPS) analysis indicates that the implanted silver is in a metallic Ag3d state without stable chemical bond formation with polymer chains. Ion implantation is found to affect the surface energy: the polar component increases while the dispersion part decreases with increasing implantation dose. Surface roughness is greater after ion implantation and the hydrophobicity increases with increasing dose, for all ion species. We find that ion implantation of Ag, Ar and C leads to a reduction in the polymer microhardness by a factor of five, while the surface electrical resistivity declines modestly.

Time domain NMR evaluation of poly(vinyl alcohol) xerogels

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, Elton Jorge da Rocha; Cavalcante, Maxwell de Paula; Tavares, Maria Ines Bruno, E-mail: mibt@ima.ufrj.br [Universidade Federal do Rio de Janeiro (IMA/UFRJ), Rio de Janeiro, RJ (Brazil). Centro de Tecnologia. Instituto de Macromoleculas Professora Eloisa Mano

2016-05-15

Poly(vinyl alcohol) (PVA)-based chemically cross-linked xerogels, both neat and loaded with nanoparticulate hydrophilic silica (SiO{sub 2}), were obtained and characterized mainly through time domain NMR experiments (TD-NMR). Fourier-transform infrared (FT-IR) and wide angle X-ray diffraction (WAXD) analyses were employed as secondary methods. TD-NMR, through the interpretation of the spin-lattice relaxation constant values and related information, showed both cross-linking and nanoparticle influences on PVA matrix. SiO{sub 2} does not interact chemically with the PVA chains, but has effect on its molecular mobility, as investigated via TD-NMR. Apparent energy of activation, spin-lattice time constant and size of spin domains in the sample have almost linear dependence with the degree of cross-linking of the PVA and are affected by the addition of SiO{sub 2}. These three parameters were derived from a single set of TD-NMR experiments, which demonstrates the versatility of the technique for characterization of inorganic-organic hybrid xerogels, an important class of materials. (author)

Tribological properties of PVA/PVP blend hydrogels against articular cartilage.

Science.gov (United States)

Kanca, Yusuf; Milner, Piers; Dini, Daniele; Amis, Andrew A

2018-02-01

This research investigated in-vitro tribological performance of the articulation of cartilage-on- polyvinyl alcohol (PVA) and polyvinyl pyrrolidone (PVP) blend hydrogels using a custom-designed multi-directional wear rig. The hydrogels were prepared by repeated freezing-thawing cycles at different concentrations and PVA to PVP fractions at a given concentration. PVA/PVP blend hydrogels showed low coefficient of friction (COF) values (between 0.12 ± 0.01 and 0.14 ± 0.02) which were closer to the cartilage-on-cartilage articulation (0.03 ± 0.01) compared to the cartilage-on-stainless steel articulation (0.46 ± 0.06). The COF increased with increasing hydrogel concentration (p = 0.03) and decreasing PVP content at a given concentration (p < 0.05). The cartilage-on-hydrogel tests showed only the surface layers of the cartilage being removed (average volume loss of the condyles was 12.5 ± 4.2mm 3 ). However, the hydrogels were found to be worn/deformed. The hydrogels prepared at a higher concentration showed lower apparent volume loss. A strong correlation (R 2 = 0.94) was found between the COF and compressive moduli of the hydrogel groups, resulting from decreasing contact congruency. It was concluded that the hydrogels were promising as hemiarthroplasty materials, but that improved mechanical behaviour was required for clinical use. Copyright © 2017 Elsevier Ltd. All rights reserved.

Efficient etching-free transfer of high quality, large-area CVD grown graphene onto polyvinyl alcohol films

International Nuclear Information System (INIS)

Marta, Bogdan; Leordean, Cosmin; Istvan, Todor; Botiz, Ioan; Astilean, Simion

2016-01-01

Graphical abstract: - Highlights: • One-step dry transfer method of CVD grown graphene onto PVA films. • Investigation of graphene quality and number of layers of the synthesized and transferred graphene. • Promising scalability and good quality of transferred graphene onto flexible transparent polymers. - Abstract: Graphene transfer is a procedure of paramount importance for the production of graphene-based electronic devices. The transfer procedure can affect the electronic properties of the transferred graphene and can be detrimental for possible applications both due to procedure induced defects which can appear and due to scalability of the method. Hence, it is important to investigate new transfer methods for graphene that are less time consuming and show great promise. In the present study we propose an efficient, etching-free transfer method that consists in applying a thin polyvinyl alcohol layer on top of the CVD grown graphene on Cu and then peeling-off the graphene onto the polyvinyl alcohol film. We investigate the quality of the transferred graphene before and after the transfer, using Raman spectroscopy and imaging as well as optical and atomic force microscopy techniques. This simple transfer method is scalable and can lead to complete transfer of graphene onto flexible and transparent polymer support films without affecting the quality of the graphene during the transfer procedure.

Efficient etching-free transfer of high quality, large-area CVD grown graphene onto polyvinyl alcohol films

Energy Technology Data Exchange (ETDEWEB)

Marta, Bogdan; Leordean, Cosmin [Babes-Bolyai University, Interdisciplinary Research Institute in Bio-Nano-Sciences, Nanobiophotonics and Laser Microspectroscopy Center, Treboniu Laurian Str. 42, Cluj-Napoca 400271 (Romania); Istvan, Todor [Babes-Bolyai University, Faculty of Physics, Biomolecular Physics Department, M Kogalniceanu Str. 1, Cluj-Napoca 400084 (Romania); Botiz, Ioan [Babes-Bolyai University, Interdisciplinary Research Institute in Bio-Nano-Sciences, Nanobiophotonics and Laser Microspectroscopy Center, Treboniu Laurian Str. 42, Cluj-Napoca 400271 (Romania); Astilean, Simion, E-mail: simion.astilean@phys.ubbcluj.ro [Babes-Bolyai University, Interdisciplinary Research Institute in Bio-Nano-Sciences, Nanobiophotonics and Laser Microspectroscopy Center, Treboniu Laurian Str. 42, Cluj-Napoca 400271 (Romania); Babes-Bolyai University, Faculty of Physics, Biomolecular Physics Department, M Kogalniceanu Str. 1, Cluj-Napoca 400084 (Romania)

2016-02-15

Graphical abstract: - Highlights: • One-step dry transfer method of CVD grown graphene onto PVA films. • Investigation of graphene quality and number of layers of the synthesized and transferred graphene. • Promising scalability and good quality of transferred graphene onto flexible transparent polymers. - Abstract: Graphene transfer is a procedure of paramount importance for the production of graphene-based electronic devices. The transfer procedure can affect the electronic properties of the transferred graphene and can be detrimental for possible applications both due to procedure induced defects which can appear and due to scalability of the method. Hence, it is important to investigate new transfer methods for graphene that are less time consuming and show great promise. In the present study we propose an efficient, etching-free transfer method that consists in applying a thin polyvinyl alcohol layer on top of the CVD grown graphene on Cu and then peeling-off the graphene onto the polyvinyl alcohol film. We investigate the quality of the transferred graphene before and after the transfer, using Raman spectroscopy and imaging as well as optical and atomic force microscopy techniques. This simple transfer method is scalable and can lead to complete transfer of graphene onto flexible and transparent polymer support films without affecting the quality of the graphene during the transfer procedure.

Effect of gamma ray on poly(lactic acid)/poly(vinyl acetate-co-vinyl alcohol) blends as biodegradable food packaging films

International Nuclear Information System (INIS)

Razavi, Seyed Mohammad; Dadbin, Susan; Frounchi, Masoud

2014-01-01

Poly(lactic acid) (PLA)/poly(vinyl acetate-co-vinyl alcohol) [P(VAc-co-VA)] blends as new transparent film packaging materials were prepared at various blend compositions and different vinyl alcohol contents. The blends and pure PLA were irradiated by gamma rays to investigate the extent of changes in the packaging material during gamma ray sterilization process. The miscibility of the blends was dependent on the blend composition and vinyl alcohol content; gamma irradiation had little effect on the extent of miscibility. The glass transition temperature of pure PLA and PLA/P(VAc-co-VA) miscible blends reduced after irradiation. On the other hand in PLA/P(VAc-co-VA) immiscible blends, while the glass transition temperature of the PLA phase decreased; that of the copolymer phase slightly increased. The reduction in the glass transition was about 10 percent for samples irradiated with 50 kGy indicating dominance of chain scission of PLA molecules at high irradiation dose. The latter was verified by drop in mechanical properties of pure PLA after exposing to gamma irradiation at 50 kGy. Blending of PLA with the copolymer P(VAc-co-VA) compensated greatly the adverse effects of irradiation on PLA. The oxygen-barrier property of the blend was superior to the neat PLA and remained almost intact with irradiation. The un-irradiated and irradiated blends had excellent transparency. Gamma ray doses used for sterilization purposes are usually less than 20 kGy. It was shown that gamma irradiation at 20 kGy had no or little adverse effects on PLA/P(VAc-co-VA) blends mechanical and gas barrier properties. - Highlights: • Poly(lactic acid)/poly(vinyl acetate-co-vinyl alcohol) blends were prepared as new packaging film. • The blends are superior to PLA in oxygen gas barrier property. • The blends are suitable for gamma ray sterilization and maintain useful mechanical properties. • The blends are perfectly transparent

Investigations on electrostatic dissipative materials derived from Poly(vinyl alcohol/ferrofluid composites

Directory of Open Access Journals (Sweden)

Winatthakan Phuchaduek

2013-10-01

Full Text Available Biodegradable polymer composites based on polyvinyl alcohol (PVA and ferrofluid (FF were prepared by solutioncasting method. Such composites were characterized by various methods in order to evaluate their potential for use as elec-trostatic dissipative (ESD materials. Effects of ferrofluid content on mechanical, thermal, and electrical properties of thecomposites were investigated. The morphology of the composites was examined by SEM and the water contact angle on thecomposite surface was also measured. Experimental results showed that surface resistivity of the composites can be reducedby the addition of FF. The abrupt transition of such resistivity occurred in the concentration range 20-30 wt.% FF. Theconductive mechanism of the proposed composites is a complex manner, including contact conduction and tunnelingconduction.

High-water-content mouldable polyvinyl alcohol-borax hydrogels reinforced by well-dispersed cellulose nanoparticles: dynamic rheological properties and hydrogel formation mechanism.

Science.gov (United States)

Han, Jingquan; Lei, Tingzhou; Wu, Qinglin

2014-02-15

Cellulose nanoparticle (CNP) reinforced polyvinyl alcohol-borax (PB) hydrogels were produced via a facile approach in an aqueous system. The effects of particle size, aspect ratio, crystal structure, and surface charge of CNPs on the rheological properties of the composite hydrogels were investigated. The rheological measurements confirmed the incorporation of well-dispersed CNPs to PB system significantly enhanced the viscoelasticity and stiffness of hydrogels. The obtained free-standing, high elasticity and mouldable hydrogels exhibited self-recovery under continuous step strain and thermo-reversibility under temperature sweep. With the addition of cellulose I nanofibers, a 19-fold increase in the high-frequency plateau of storage modulus was obtained compared with that of the pure PB. CNPs acted as multifunctional crosslinking agents and nanofillers to physically and chemically bridge the 3D network hydrogel. The plausible mechanism for the multi-complexation between CNPs, polyvinyl alcohol and borax was proposed to understand the relationship between the 3D network and hydrogel properties. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of PVA(Polyvinyl Alcohol) on Supercooling Phenomena of Water

Science.gov (United States)

Kumano, Hiroyuki; Saito, Akio; Okawa, Seiji; Takizawa, Hiroshi

In this paper, effects of polymer additive on supercooling of water were investigated experimentally. Poly-vinyl alcohol (PVA) were used as the polymer, and the samples were prepared by dissolving PVA in ultra pure water. Concentration, degree of polymerization and saponification of PVA were varied as the experimental parameters. The sample was cooled, and the temperature at the instant when ice appears was measured. Since freezing of supercooled water is statistical phenomenon, many experiments were carried out and average degrees of supercooling were obtained for each experimental condition. As the result, it was found that PVA affects nucleation of supercooling and the degree of supercooling increases by adding the PVA. Especially, it is found that the average degree of supercooling increases and the standard deviation of average degree of supercooling decreases with increase of degree of saponification of PVA. However, the average degree of supercooling are independent of the degree of polymerization of PVA in the range of this study.

Effects of poly-vinyl alcohol on supercooling phenomena of water

Energy Technology Data Exchange (ETDEWEB)

Kumano, Hiroyuki; Hirata, Tetsuo; Kudoh, Tomoya [Department of Mechanical Systems Engineering, Shinshu University, 4-17-1, Wakasato, Nagano City, 380-8553 (Japan)

2009-05-15

The effects of a polymer additive on the supercooling of water were investigated experimentally. Poly-vinyl alcohols (PVAs) were used as the additives, and samples were prepared by dissolving the PVA in water. Since the characteristics of PVA are decided by its degrees of polymerization and saponification, these were varied along with the concentration as the experimental parameters. Moreover, the effect of purity of the water was also considered. Each sample was cooled and the temperature at the instant when ice appeared was measured. Since the freezing of supercooled water is a statistical phenomenon, many experiments were carried out and the average degree of supercooling was obtained. It was found that PVA affects the nucleation of ice in supercooled water and the degree of supercooling increases with the addition of PVA even for water with low purity. The average degree of supercooling increases with an increase in the degree of saponification of PVA. (author)

Mechanical, Thermal, and Microstructural Analysis of Polyvinyl Alcohol/Montmorillonite Nanocomposites

Directory of Open Access Journals (Sweden)

P. G. Allison

2015-01-01

Full Text Available Structural biomaterials such as nacre, bone, and fish scales possess unique structures that have hierarchical spatial configurations, which provide excellent mechanical properties when compared to their individual constituents. These observations have been the motivation for designing and characterizing bioinspired materials with high strength, high stiffness, and corrosion-resistant properties while at the same time being environmentally friendly. It has been demonstrated that polymer-clay nanocomposites can simulate the behavior of nacreous biomaterials such as abalone shell. Mechanical, thermal, and microstructural analyses characterized solution-cast polyvinyl alcohol (PVA/montmorillonite (MMT nanocomposite properties over compositions ranging from the neat polymer to 25% volume fraction of MMT nanoclay. Uniaxial tensile experiments were performed at displacement rates of 1 mm/min and 50 mm/min. Strength values are similar to those shown by nacre and represent a homogeneous dispersion of the MMT in the polymer matrix. Strength-to-weight ratios are similar to many structural metals.

Polymer and Water Dynamics in Poly(vinyl alcohol/Poly(methacrylate Networks. A Molecular Dynamics Simulation and Incoherent Neutron Scattering Investigation

Directory of Open Access Journals (Sweden)

Ester Chiessi

2011-10-01

Full Text Available Chemically cross-linked polymer networks of poly(vinyl alcohol/poly(methacrylate form monolitic hydrogels and microgels suitable for biomedical applications, such as in situ tissue replacement and drug delivery. In this work, molecular dynamics (MD simulation and incoherent neutron scattering methods are used to study the local polymer dynamics and the polymer induced modification of water properties in poly(vinyl alcohol/poly(methacrylate hydrogels. This information is particularly relevant when the diffusion of metabolites and drugs is a requirement for the polymer microgel functionality. MD simulations of an atomic detailed model of the junction domain at the experimental hydration degree were carried out at 283, 293 and 313 K. The polymer-water interaction, the polymer connectivity and the water dynamics were investigated as a function of temperature. Simulation results are compared with findings of elastic and quasi-elastic incoherent neutron scattering measurements, experimental approaches which sample the same space-time window of MD simulations. This combined analysis shows a supercooled water component and an increase of hydrophilicity and mobility with temperature of these amphiphilic polymer networks.

Gamma irradiation Effect on the Non-Crosslinked and Crosslinked Poly(vinyl alcohol) Films

International Nuclear Information System (INIS)

El-Sawy, N.M.; El-Arnaouty, M.B.; Abdel Ghaffar, A.M.

2008-01-01

The non-crosslinked and crosslinked poly(vinyl alcohol) (PVA) films were prepared by the cast method then irradiated with gamma rays for various doses up to 300 kGy. The structure and characterization of PVA were determined by using Infrared spectroscopy (FTIR), ultraviolet spectroscopy (UV). Swelling behaviour was also investigated. Mechanical properties have been examined with respect to the absorbed dose. The color of the films changed to yellowish-white after irradiation. Additional changes were observed using FTIR analysis on the degradation products demonstrated that the radiolysis of PVA was initiated by liberation of H and OH groups leading to scission of the main chains and formation of carbonyl and double bond groups. Thermogravimetric analysis (TGA) was performed

Synthesis of Monodispersed Gold Nanoparticles with Exceptional Colloidal Stability with Grafted Polyethylene Glycol-g-polyvinyl Alcohol

Directory of Open Access Journals (Sweden)

Alaaldin M. Alkilany

2015-01-01

Full Text Available Herein, we report the synthesis of spherical gold nanoparticles with tunable core size (23–79 nm in the presence of polyethylene glycol-g-polyvinyl alcohol (PEG-g-PVA grafted copolymer as a reducing, capping, and stabilizing agent in a one-step protocol. The resulted PEG-g-PVA-capped gold nanoparticles are monodispersed with an exceptional colloidal stability against salt addition, repeated centrifugation, and extensive dialysis. The effect of various synthesis parameters and the kinetic/mechanism of the nanoparticle formation are discussed.

Nanofibre Electrospinning Poly(vinyl alcohol and Cellulose Composite Mats Obtained by Use of a Cylindrical Electrode

Directory of Open Access Journals (Sweden)

Anna Sutka

2013-01-01

Full Text Available A study of nanofibre composites obtained by electrospinning from poly(vinyl alcohol (PVA solutions of steam exploded hemp fibres and shives is reported. A combined treatment of steam explosion (SE, ball milling, and high-intensity ultrasound (HIUS is applied to prepare cellulose nanofibres (CNF from hemp fibres (CNF-F and shives (CNF-S. The reflectance Fourier transform infrared (FTIR ATR spectroscopy is used to analyze the obtained PVA/CNF composite mats. Morphology of the PVA/CNF composites was studied by scanning electron microscopy (SEM.

Microwave-Assisted Synthesis of Chitosan/Polyvinyl Alcohol Silver Nanoparticles Gel for Wound Dressing Applications

Directory of Open Access Journals (Sweden)

Nguyen Thi Hiep

2016-01-01

Full Text Available The purpose of this study was to fabricate chitosan/poly(vinyl alcohol/Ag nanoparticles (CPA gels with microwave-assistance for skin applications. Microwave irradiation was employed to reduce silver ions to silver nanoparticles and to crosslink chitosan (CS with polyvinyl alcohol (PVA. The presence of silver nanoparticles in CPA gels matrix was examined using UV-Vis spectroscopy, transmission electron microscopy, and X-ray diffraction. The interaction of CS and PVA was analysed by Fourier transform infrared spectroscopy. The release of silver ions was determined by atomic absorption spectrometry. The antimicrobial properties of CPA gels against P. aeruginosa and S. aureus were investigated using agar diffusion method. Finally, the biocompatibility and wound-healing ability of the gels were studied using fibroblast cells (in vitro and mice models (in vivo. In conclusion, the results showed that CPA gels were successfully fabricated using microwave irradiation method. These gels can be applied to heal an open wound thanks to their antibacterial activity and biocompatibility.

Study of polyvinyl alcohol nanofibrous membrane by electrospinning as a magnetic nanoparticle delivery approach

International Nuclear Information System (INIS)

Ger, Tzong-Rong; Huang, Hao-Ting; Hu, Keng-Shiang; Huang, Chen-Yu; Lai, Jun-Yang; Chen, Jiann-Yeu; Lai, Mei-Feng

2014-01-01

Electrospinning technique was used to fabricate polyvinyl alcohol (PVA)-based magnetic biodegradable nanofibers. PVA solution was mixed with ferrofluid or magnetic nanoparticles (MNPs) powder and formed two individual nanofibrous membranes (PVA/ferrofluid and PVA/MNPs powder) by electrospinning. The surface morphology of the nanofibrous membrane was characterized by scanning electron microscopy and the magnetic properties were measured by vibrating sample magnetometer. Macrophages (RAW 264.7) were co-cultured with the nanofibrous membranes for 12, 24, and 48 h and exhibited good cell viability (>95%). Results showed that the PVA fibers would be degraded and the embedded Fe 3 O 4 nanoparticles would be released and delivered to cells

Study of polyvinyl alcohol nanofibrous membrane by electrospinning as a magnetic nanoparticle delivery approach

Energy Technology Data Exchange (ETDEWEB)

Ger, Tzong-Rong; Huang, Hao-Ting; Hu, Keng-Shiang [Institute of NanoEngineering and MicroSystems, National Tsing Hua University, Hsinchu, Taiwan (China); Huang, Chen-Yu [Department of Power Mechanical Engineering, National Tsing Hua University, Hsinchu, Taiwan (China); Lai, Jun-Yang [Department of Applied Physics, National Ping Tung University of Education, Pingtung, Taiwan (China); Chen, Jiann-Yeu [Center of Nanoscience and Nanotechnology, National Chung Hsing University, Taichung, Taiwan (China); Lai, Mei-Feng, E-mail: mflai@mx.nthu.edu.tw [Institute of NanoEngineering and MicroSystems, National Tsing Hua University, Hsinchu, Taiwan (China); Department of Power Mechanical Engineering, National Tsing Hua University, Hsinchu, Taiwan (China)

2014-05-07

Electrospinning technique was used to fabricate polyvinyl alcohol (PVA)-based magnetic biodegradable nanofibers. PVA solution was mixed with ferrofluid or magnetic nanoparticles (MNPs) powder and formed two individual nanofibrous membranes (PVA/ferrofluid and PVA/MNPs powder) by electrospinning. The surface morphology of the nanofibrous membrane was characterized by scanning electron microscopy and the magnetic properties were measured by vibrating sample magnetometer. Macrophages (RAW 264.7) were co-cultured with the nanofibrous membranes for 12, 24, and 48 h and exhibited good cell viability (>95%). Results showed that the PVA fibers would be degraded and the embedded Fe{sub 3}O{sub 4} nanoparticles would be released and delivered to cells.

Gamma-irradiation effect on dielectric properties of vanadate doped polyvinyl alcohol

International Nuclear Information System (INIS)

Abo-Ellil, M.S.; Ahmed, M.A.; El-Ahdal, M.A.

1997-01-01

The real part of the dielectric constant (ε) for different concentrations (1%, 2% and 3% by wt.) of the ammonium meta vanadate doped polyvinyl alcohol was measured as a function of temperature and frequency. Different γ-ray doses (2.0, 5.0 and 10kGy) were used for samples irradiation. The dielectric constant of the samples reveals more than one peak depending on the vanadate concentration as well as the applied frequency. The main relaxation peak was discussed with reference degradation and crosslinking that vary drastically with the γ-dose. The hump that appeared at high temperature was found to be due to order-disorder transition. The variation of the internal dynamic viscosity of the sample by irradiation was found to play a role in the polarization process as well as (ε) values. Gradual increase in (ε) was obtained by increasing the γ-dose. (author)

Luminescence study of ZnSe/PVA (polyvinyl alcohol) composite film

Energy Technology Data Exchange (ETDEWEB)

Lahariya, Vikas [Amity School of Applied Science, Amity University Haryana Panchgaon, Manesar, Haryana 122413 (India)

2016-05-06

The ZnSe nanocrystals have been prepared into poly vinyl alcohol(PVA) polymer matrix on glass using ZnCl2 and Na2SeSO3 as zinc and selenium source respectively. Poly vinyl Alcohol (PVA) used as polymer matrix cum capping agent due to their high viscosity and water solubility. It is transparent for visible region and prevents Se- ions to photo oxidation. The ZnSe/PVA composite film was deposited on glass substrate. The film was characterized by X Ray Diffraction (XRD) and UV-Visible absorption Spectroscopy and Photoluminescence. The X Ray Diffraction (XRD) study confirms the nanometer size (10 nm) particle formation within PVA matrix with cubic zinc blend crystal structure. The UV-Visible Absorption spectrum of ZnSe/PVA composite film shown blue shift in absorption edge indicating increased band gap due to quantum confinement. The calculated energy band gap from the absorption edge using Tauc relation is 3.4 eV. From the Photoluminescence study a broad peak at 435 nm has been observed in violet blue region due to recombination of surface states.

Poly(vinyl alcohol) gels as photoacoustic breast phantoms revisited.

Science.gov (United States)

Xia, Wenfeng; Piras, Daniele; Heijblom, Michelle; Steenbergen, Wiendelt; van Leeuwen, Ton G; Manohar, Srirang

2011-07-01

A popular phantom in photoacoustic imaging is poly(vinyl alcohol) (PVA) hydrogel fabricated by freezing and thawing (F-T) aqueous solutions of PVA. The material possesses acoustic and optical properties similar to those of tissue. Earlier work characterized PVA gels in small test specimens where temperature distributions during F-T are relatively homogeneous. In this work, in breast-sized samples we observed substantial temperature differences between the shallow regions and the interior during the F-T procedure. We investigated whether spatial variations were also present in the acoustic and optical properties. The speed of sound, acoustic attenuation, and optical reduced scattering coefficients were measured on specimens sampled at various locations in a large phantom. In general, the properties matched values quoted for breast tissue. But while acoustic properties were relatively homogeneous, the reduced scattering was substantially different at the surface compared with the interior. We correlated these variations with gel microstructure inspected using scanning electron microscopy. Interestingly, the phantom's reduced scattering spatial distribution matches the optical properties of the standard two-layer breast model used in x ray dosimetry. We conclude that large PVA samples prepared using the standard recipe make excellent breast tissue phantoms.

Development of hydroxyapatite/polyvinyl alcohol bionanocomposite for prosthesis implants

Science.gov (United States)

Karthik, V.; Pabi, S. K.; Chowdhury, S. K. Roy

2018-02-01

Hydroxyapatite (Ca10(PO4)6(OH)2) has similar structural and chemical properties of natural bone mineral and hence widely used as a bone replacement substitute. Natural bone consists of hydroxyapatite and collagen. For mimicking the natural, in the present work, a sintered porous hydroxyapatite component has been vacuum impregnated with Polyvinyl alcohol (PVA), which has better properties like biocompatibility, biodegradability and water- solubility. Hydroxyapatite powders have been made into nanosize to reduce the melting point and hence the sintering temperature. In the present investigation high energy ball mill is used to produce nano-hydroxyapatite powders in bulk quantity by optimizing the milling parameters using stainless steel grinding media. Pellets of 10 mm diameter have been produced from nano- hydroxyapatite powders under different uniaxial compaction pressures. The pellets have been sintered to form porous compacts. The vacuum impregnation of sintered pallets with PVA solution of different strength has been done to find the optimum impregnation condition. Microhardness, compressive strength, wear loss and haemocompatibility of hydroxyapatite ceramics have been studied before and after impregnation of PVA. The nano- hydroxyapatite/PVA composites have superior mechanical properties and reduced wear loss than the non-impregnated porous nano-hydroxyapatite ceramics.

Morphology and dispersion of FeCo alloy nanoparticles dispersed in a matrix of IR pyrolized polyvinyl alcohol

Science.gov (United States)

Vasilev, A. A.; Dzidziguri, E. L.; Muratov, D. G.; Zhilyaeva, N. A.; Efimov, M. N.; Karpacheva, G. P.

2018-04-01

Metal-carbon nanocomposites consisting of FeCo alloy nanoparticles dispersed in a carbon matrix were synthesized by the thermal decomposition method of a precursor based on polyvinyl alcohol and metals salts. The synthesized powders were investigated by X-ray diffraction (XRD), X-ray fluorescent spectrometry (XRFS), transmission electron microscopy (TEM) and scanning electron microscopy (SEM). Surface characteristics of materials were measured by BET-method. The morphology and dispersity of metal nanoparticles were studied depending on the metals ratio in the composite.

Chemically imaging the effects of the addition of nanofibrillated cellulose on the distribution of poly(acrylic acid) in poly(vinyl alcohol)

Science.gov (United States)

Craig Clemons; Julia Sedlmair; Barbara Illman; Rebecca Ibach; Carol Hirschmugl

2013-01-01

The distribution of poly(acrylic acid) (PAA) in model laminates of nanocellulose and poly(vinyl alcohol) (PVOH) was investigated by FTIR chemical imaging. The method was effective in spatially discerning the three components of the composite. PAA can potentially improve the performance of nanocellulose reinforced PVOH by not only crosslinking the PVOH matrix but also...

PIXE investigation of in vitro release of chloramphenicol across polyvinyl alcohol/acrylamide hydrogel

International Nuclear Information System (INIS)

Rihawy, M.S.; Alzier, A.; Allaf, A.W.

2011-01-01

Hydrogels based on polyvinyl alcohol and different amounts of acrylamide monomer were prepared by thermal cross-linking in the solid state. The hydrogels were investigated for drug delivery system applications. Chloramphenicol was adopted as a model drug to study its release behavior. Particle induced X-ray emission was utilized to study the drug release behavior across the hydrogels and a comparison study with ultraviolet measurements was performed. Fourier Transform Infrared measurements were carried out for molecular characterization. The releasing behavior of the drug exhibits a decrease and a subsequent increase in the release rate, as the acrylamide monomer increases. Characterization of the hydrogels has shown a competitive behavior between crosslinking with AAm acrylamide monomer or oligomerized version, depending on the amount added to prepare the hydrogels.

An evaluation of the thermal and mechanical properties of a salt-modified polyvinyl alcohol hydrogel for a knee meniscus application.

Science.gov (United States)

Curley, Colin; Hayes, Jennifer C; Rowan, Neil J; Kennedy, James E

2014-12-01

The treatment of irreparable knee meniscus tears remains a major challenge for the orthopaedic community. The main purpose of this research was to analyse the mechanical properties and thermal behaviour of a salt-modified polyvinyl alcohol hydrogel, in order to assess its potential for use as an artificial meniscal implant. Aqueous poly vinyl alcohol was treated with a sodium sulphate solution to precipitate out the polyvinyl alcohol resulting in a pliable hydrogel. The freeze-thaw process, a strictly physical method of crosslinking, was employed to crosslink the hydrogel. Physical crosslinks in the form of crystalline regions were induced within the hydrogel structure which resulted in a large increase in mechanical resistance. Results showed that the optimal sodium sulphate addition of 6.6% (w/v) Na2SO4 in 8.33% (w/v) PVA causes the PVA to precipitate out of its solution. The effect of multiple freeze thaw cycles was also investigated. Investigation comprised of a variety of well-established characterisation techniques such as differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), mechanical analysis, rheometry and swelling studies. DSC analysis showed that samples cross-linked using the freeze thaw process display a thermal shift due to increased crosslink density. FTIR analysis confirmed crystallisation is present at 1142cm(-1) and also showed that no chemical alteration occurs when PVA is treated with sodium sulphate. Swelling studies indicated that that PVA/sodium sulphate hydrogels absorb less water than untreated hydrogels due to increased amounts of PVA present. Compressive strength analysis of PVA/sodium sulphate hydrogels prepared at -80°C displayed average maximum loads of 2472N, 2482.4N and 2476N of over 1, 3 and 5 freeze thaw cycles respectively. Mechanical analysis of the hydrogel indicated that the material is thermally stable and resistant to breakdown by compressive force. These properties are crucial for

Ultrasonic-assisted synthesis of novel nanocomposite of poly(vinyl alcohol) and amino-modified MCM-41: A green adsorbent for Cd(II) removal.

Science.gov (United States)

Soltani, Roozbeh; Dinari, Mohammad; Mohammadnezhad, Gholamhossein

2018-01-01

Amino-modified MCM-41/poly(vinyl alcohol) nanocomposite (M-MCM-41/PVOH NC) was developed for the adsorption of Cd(II) from aqueous media. M-MCM-41/PVOH NC was prepared through ultrasonic-assisted and simple blending procedure with economical and environmentally friendly polymer. The as-prepared adsorbent was characterized by FT-IR, TEM, FE-SEM and TGA. The contact time, solution pH and initial concentration of Cd(II) were found to affect the adsorption of Cd(II) from aqueous media. Kinetic studies were carried out and pseudo-first-order (PFO), pseudo-second-order (PSO), Elovich, and intra-particle diffusion (IPD) reaction kinetic models were examined. The kinetic results revealed that the adsorption of Cd(II) onto M-MCM-41/PVOH NC followed PSO kinetic model and is a chemical adsorption. The equilibrium adsorption data were evaluated by different isotherms viz. Langmuir, Freundlich, and Dubinin Radushkevich (D-R) equations. The equilibrium data fitted better with the Langmuir isotherm and the maximum adsorption capacity of M-MCM-41/PVOH NC at 298K was calculated to be 46.73mgg -1 for Cd(II) on a typical saturated monomolecular layer with a fixed number of localized adsorption sites. Copyright © 2017 Elsevier B.V. All rights reserved.

Permanent hydrophilic modification of polypropylene and poly(vinyl alcohol) films by vacuum ultraviolet radiation

Energy Technology Data Exchange (ETDEWEB)

Belmonte, Guilherme Kretzmann [Instituto de Química, Universidade Federal do Rio Grande do Sul (UFRGS), Avenida Bento Gonçalves 9500, 91501-970 Porto Alegre, RS (Brazil); Charles, German [Centro de Química Aplicada (CEQUIMAP), Facultad de Ciencias Químicas, Unversidad Nacional de Córdoba, Haya de la Torre y Medina Allende, Edificio de Ciencias II, Ciudad Universitaria, Córdoba 5000 (Argentina); Strumia, Miriam Cristina [Departamento de Química Orgánica, Facultad de Ciencias Químicas, Universidad Nacional de Córdoba, IPQA-Conicet, Haya de la Torre y Medina Allende, Edificio de Ciencias II, Ciudad Universitaria, Córdoba 5000 (Argentina); Weibel, Daniel Eduardo, E-mail: danielw@iq.ufrgs.br [Instituto de Química, Universidade Federal do Rio Grande do Sul (UFRGS), Avenida Bento Gonçalves 9500, 91501-970 Porto Alegre, RS (Brazil)

2016-09-30

Highlights: • Polypropylene and Poly(vinyl alcohol) were surface modified by vacuum ultraviolet (VUV) irradiation. • The hydrophilicity of the treated films was permanent and resisted aging for several months. • Grafting of styrene monomer was only observed in the VUV irradiated regions. • The obtained results showed the potential in the use of VUV treatment for surface modification and processing of polymers which lack chromophores in the UV region. - Abstract: Polypropylene (PP) and Poly(vinyl alcohol) (PVA) both synthetics polymers but one of them biodegradable, were surface modified by vacuum ultraviolet (VUV) irradiation. After VUV irradiation in an inert nitrogen atmosphere, the films were exposed to oxygen gas. The treated films were characterized by water contact angle measurements (WCA), optical profilometry, FTIR-ATR, XPS, UPS and NEXAFS techniques. PP and PVA VUV-treated films reached superhydrophilic conditions (WCAs <10°) in about 30 min of irradiation under our experimental conditions. It was observed that when the WCAs reached about 35–40° the hydrophilicity was permanent in both polymers. These results contrasted with typical plasma treatments were a rapid hydrophobic recovery with aging time is usually observed. UPS and XPS data showed the presence of new functionalities on the PP and PVA surfaces that were assigned to COO, C=O, C−O and C=C functional groups. Finally, grafting of styrene (ST) as a typical monomer was tested on PP films. It was confirmed that only in the VUV irradiated region an efficient grafting of ST or polymerized ST was found. Outside the irradiated regions no ST grafted was observed. Our results showed the potential use of VUV treatment for surface modification and processing of polymers which lack chromophores in the UV region.

Optical and structural behaviors of crosslinked polyvinyl alcohol thin films

Science.gov (United States)

Pandit, Subhankar; Kundu, Sarathi

2018-04-01

Polyvinyl Alcohol (PVA) has excellent properties like uniaxial tensile stress, chemical resistance, biocompatibility, etc. The properties of PVA further can be tuned by crosslinking process. In this work, a simple heat treatment method is used to find out the optimum crosslinking of PVA and the corresponding structural and optical responses are explored. The PVA crosslinking is done by exposing the films at different temperatures and time intervals. The optical property of pure and heat treated PVA films are investigated by UV-Vis absorption and photoluminescence emission spectroscopy and structural modifications are studied by Fourier Transform Infrared Spectroscopy (FTIR). The absorption peaks of pure PVA are observed at ≈ 280 and 335 nm and the corresponding emission is observed at ≈ 424 nm. The pure PVA showed modified optical behaviors after the heat treatment. In addition, dipping the PVA films in hot water (85°C) for nearly 20 minutes also show impact on both structural and optical properties. From FTIR spectroscopy, the changes in vibrational band positions confirm the structural modifications of PVA films.

Radiation effect on PVC/ENR blends

International Nuclear Information System (INIS)

Chantara Thevy Ratnam; Khairul Zaman Mohd Dahlan

1997-01-01

The effect of irradiation on the physical properties of Polyvinyl Chloride / Epoxidised Natural Rubber Blends (PVC/ENR blends) were investigated. The enhancement in tensile strength, elongation at break, hardness and aging properties of the blends have confirmed the positive effect of irradiation on the blends. It is evident from gel fraction and infra red spectroscopic studies that the blends of PVC and ENR cross-linked upon irradiation. The results also revealed that at any blend composition, the enhancement in properties depend on irradiation dose which controls the degree of radiation induced cross-linking. In an attempt to maximize the constructive effect of irradiation, the influence of various additives such as stabilizers, radiation sensitizers, fillers and processing aids on the blend properties were studied. The changes in blend properties upon irradiation with the presents of above additives were also presented in this paper

Solid Particle Erosion of Date Palm Leaf Fiber Reinforced Polyvinyl Alcohol Composites

Directory of Open Access Journals (Sweden)

Jyoti R. Mohanty

2014-01-01

Full Text Available Solid particle erosion behavior of short date palm leaf (DPL fiber reinforced polyvinyl alcohol (PVA composite has been studied using silica sand particles (200 ± 50 μm as an erodent at different impingement angles (15–90° and impact velocities (48–109 m/s. The influence of fiber content (wt% of DPL fiber on erosion rate of PVA/DPL composite has also been investigated. The neat PVA shows maximum erosion rate at 30° impingement angle whereas PVA/DPL composites exhibit maximum erosion rate at 45° impingement angle irrespective of fiber loading showing semiductile behavior. The erosion efficiency of PVA and its composites varies from 0.735 to 16.289% for different impact velocities studied. The eroded surfaces were observed under scanning electron microscope (SEM to understand the erosion mechanism.

Effect of gamma ray on poly(lactic acid)/poly(vinyl acetate-co-vinyl alcohol) blends as biodegradable food packaging films

Science.gov (United States)

Razavi, Seyed Mohammad; Dadbin, Susan; Frounchi, Masoud

2014-03-01

Poly(lactic acid) (PLA)/poly(vinyl acetate-co-vinyl alcohol) [P(VAc-co-VA)] blends as new transparent film packaging materials were prepared at various blend compositions and different vinyl alcohol contents. The blends and pure PLA were irradiated by gamma rays to investigate the extent of changes in the packaging material during gamma ray sterilization process. The miscibility of the blends was dependent on the blend composition and vinyl alcohol content; gamma irradiation had little effect on the extent of miscibility. The glass transition temperature of pure PLA and PLA/P(VAc-co-VA) miscible blends reduced after irradiation. On the other hand in PLA/P(VAc-co-VA) immiscible blends, while the glass transition temperature of the PLA phase decreased; that of the copolymer phase slightly increased. The reduction in the glass transition was about 10 percent for samples irradiated with 50 kGy indicating dominance of chain scission of PLA molecules at high irradiation dose. The latter was verified by drop in mechanical properties of pure PLA after exposing to gamma irradiation at 50 kGy. Blending of PLA with the copolymer P(VAc-co-VA) compensated greatly the adverse effects of irradiation on PLA. The oxygen-barrier property of the blend was superior to the neat PLA and remained almost intact with irradiation. The un-irradiated and irradiated blends had excellent transparency. Gamma ray doses used for sterilization purposes are usually less than 20 kGy. It was shown that gamma irradiation at 20 kGy had no or little adverse effects on PLA/P(VAc-co-VA) blends mechanical and gas barrier properties.

Optimization of Microencapsulation Composition of Menthol, Vanillin, and Benzyl Acetate inside Polyvinyl Alcohol with Coacervation Method for Application in Perfumery

Science.gov (United States)

Sahlan, Muhamad; Raihani Rahman, Mohammad

2017-07-01

One of many applications of essential oils is as fragrance in perfumery. Menthol, benzyl acetate, and vanillin, each represents olfactive characteristic of peppermint leaves, jasmine flowers, and vanilla beans, are commonly used in perfumery. These components are highly volatile, hence the fragrance components will quickly evaporate resulting in short-lasting scent and low shelf life. In this research, said components have been successfully encapsulated simultaneously inside Polyvinyl Alcohol (PVA) using simple coacervation method to increase its shelf life. Optimization has been done using Central Composite Diagram with 4 independent variables, i.e. composition of menthol, benzyl acetate, vanillin, and tergitol 15-S-9 (as emulsifier). Encapsulation efficiency, loading capacity, and microcapsule size have been measured. In optimized composition of menthol (13.98 %w/w), benzyl acetate (14.75 %w/w), vanillin (17.84 %w/w), and tergitol 15-S-9 (13.4 %w/w) encapsulation efficiency of 97,34% and loading capacity of 46,46% have been achieved. Mean diameter of microcapsule is 20,24 μm and within range of 2,011-36,24 μm. Final product was achieved in the form of cross linked polyvinyl alcohol with hydrogel consistency and orange to yellow in color.

Preparation of poly(vinyl alcohol)-grafted graphene oxide/poly(vinyl alcohol) nanocomposites via in-situ low-temperature emulsion polymerization and their thermal and mechanical characterization

Science.gov (United States)

Zhang, Shengchang; Liu, Pengqing; Zhao, Xiangsen; Xu, Jianjun

2017-02-01

An in-situ polymerization combined with chemical grafting modification method for preparing Poly(vinyl alcohol)-grafted graphene oxide/Poly(vinyl alcohol) (PVA-g-GO/PVA) nanocomposites was reported. Firstly, Poly(vinyl acetate)-grafted graphene oxide/Poly(vinyl acetate) nanocomposites were prepared, and then the PVA-g-GO/PVA nanocomposites could be obtained through alcoholysis reaction. X-ray photoelectron spectrometer and fourier-transform infrared spectrometer confirmed that the PVAc or PVA chains were successfully grafted to GO sheets during in-situ polymerization and alcoholysis. And the results from transmission electron microscopy, scanning electron microscopy and X-ray diffraction showed that the well compatibility and homogenous dispersion of PVA-g-GO in PVA matrix could be achieved. Differential scanning calorimetric, thermogravimetry analysis and tensile test were employed to study the thermal and mechanical properties of the PVA-g-GO/PVA nanocomposites. The results indicated that a 53% improvement of tensile strength and a 36% improvement of Young's modulus were achieved by addition of 0.5 wt% of GO sheets. And the glass transition temperature of PVA-g-GO/PVA nanocomposites was increased, and their thermal stability and crystallization degree were both decreased. Due to well dispersion of fillers and strong interfacial interactions at the filler-matrix interface, in-situ polymerization combined with chemical grafting modification was a good choice to prepare graphene/PVA nanocomposite with excellent mechanical properties.

Blends of synthetic and natural polymers as drug delivery systems for growth hormone.

Science.gov (United States)

Cascone, M G; Sim, B; Downes, S

1995-05-01

In order to overcome the biological deficiencies of synthetic polymers and to enhance the mechanical characteristics of natural polymers, two synthetic polymers, poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA) were blended, in different ratios, with two biological polymers, collagen (C) and hyaluronic acid (HA). These blends were used to prepare films, sponges and hydrogels which were loaded with growth hormone (GH) to investigate their potential use as drug delivery systems. The GH release was monitored in vitro using a specific enzyme-linked immunosorbent assay. The results show that GH can be released from HA/PAA sponges and from HA/PVA and C/PVA hydrogels. The initial GH concentration used for sample loading affected the total quantity of GH released but not the pattern of release. The rate and quantity of GH released was significantly dependent on the HA or C content of the polymers.

Immobilization of ammonia-oxidizing bacteria by polyvinyl alcohol and sodium alginate.

Science.gov (United States)

Dong, Yuwei; Zhang, Yanqiu; Tu, Baojun

Ammonia-oxidizing bacteria were immobilized by polyvinyl alcohol (PVA) and sodium alginate. The immobilization conditions and ammonia oxidation ability of the immobilized bacteria were investigated. The following immobilization conditions were observed to be optimal: PVA, 12%; sodium alginate, 1.1%; calcium chloride, 1.0%; inoculum concentration, 1.3 immobilized balls/mL of immobilized medium; pH, 10; and temperature, 30°C. The immobilized ammonia-oxidizing bacteria exhibited strong ammonia oxidation ability even after being recycled four times. The ammonia nitrogen removal rate of the immobilized ammonia-oxidizing bacteria reached 90.30% under the optimal immobilization conditions. When compared with ammonia-oxidizing bacteria immobilized by sodium alginate alone, the bacteria immobilized by PVA and sodium alginate were superior with respect to pH resistance, the number of reuses, material cost, heat resistance, and ammonia oxidation ability. Copyright © 2017 Sociedade Brasileira de Microbiologia. Published by Elsevier Editora Ltda. All rights reserved.

Intermediate Alcohol-Gasoline Blends, Fuels for Enabling Increased Engine Efficiency and Powertrain Possibilities

Energy Technology Data Exchange (ETDEWEB)

Splitter, Derek A [ORNL; Szybist, James P [ORNL

2014-01-01

The present study experimentally investigates spark-ignited combustion with 87 AKI E0 gasoline in its neat form and in mid-level alcohol-gasoline blends with 24% vol./vol. iso-butanol-gasoline (IB24) and 30% vol./vol. ethanol-gasoline (E30). A single-cylinder research engine is used with a low and high compression ratio of 9.2:1 and 11.85:1 respectively. The engine is equipped with hydraulically actuated valves, laboratory intake air, and is capable of external exhaust gas recirculation (EGR). All fuels are operated to full-load conditions with =1, using both 0% and 15% external cooled EGR. The results demonstrate that higher octane number bio-fuels better utilize higher compression ratios with high stoichiometric torque capability. Specifically, the unique properties of ethanol enabled a doubling of the stoichiometric torque capability with the 11.85:1 compression ratio using E30 as compared to 87 AKI, up to 20 bar IMEPg at =1 (with 15% EGR, 18.5 bar with 0% EGR). EGR was shown to provide thermodynamic advantages with all fuels. The results demonstrate that E30 may further the downsizing and downspeeding of engines by achieving increased low speed torque, even with high compression ratios. The results suggest that at mid-level alcohol-gasoline blends, engine and vehicle optimization can offset the reduced fuel energy content of alcohol-gasoline blends, and likely reduce vehicle fuel consumption and tailpipe CO2 emissions.

UV-responsive polyvinyl alcohol nanofibers prepared by electrospinning

Energy Technology Data Exchange (ETDEWEB)

Khatri, Zeeshan, E-mail: zeeshan.khatri@faculty.muet.edu.pk [Department of Textile Engineering, Mehran University of Engineering and Technology, Jamshoro 76062 (Pakistan); Nano Fusion Technology Research Lab, Division of Frontier Fibers, Institute for Fiber Engineering (IFES), Interdisciplinary Cluster for Cutting Edge Research (ICCER), Shinshu University, 3-15-1, Tokida, Ueda, Nagano 386-8567 (Japan); Ali, Shamshad [Department of Textile Engineering, Mehran University of Engineering and Technology, Jamshoro 76062 (Pakistan); Department of Organic and Nano Engineering, Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of); Khatri, Imran [Department of Entomology, Sindh Agriculture University, Tandojam (Pakistan); Mayakrishnan, Gopiraman [Nano Fusion Technology Research Lab, Division of Frontier Fibers, Institute for Fiber Engineering (IFES), Interdisciplinary Cluster for Cutting Edge Research (ICCER), Shinshu University, 3-15-1, Tokida, Ueda, Nagano 386-8567 (Japan); Kim, Seong Hun [Department of Organic and Nano Engineering, Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea, Republic of); Kim, Ick-Soo, E-mail: kim@shinshu-u.ac.jp [Nano Fusion Technology Research Lab, Division of Frontier Fibers, Institute for Fiber Engineering (IFES), Interdisciplinary Cluster for Cutting Edge Research (ICCER), Shinshu University, 3-15-1, Tokida, Ueda, Nagano 386-8567 (Japan)

2015-07-01

Graphical abstract: - Highlights: • UV responsive PVA nanofibers were prepared via electrospinning. • Quick response codes were recorded multiple times on UV responsive nanofibers. • The rate of photo-coloration was found faster than the rate of photo-reversibility. - Abstract: We report UV-responsive polyvinyl alcohol (PVA) nanofibers for potential application for recording and erasing quick response (QR) codes. We incorporate 1′-3′-dihydro-8-methoxy-1′,3′,3′-trimethyl-6-nitrospiro [2H-1-benzopyran-2,2′-(2H)-indole] (indole) and,3-dihydro-1,3,3-trimethylspiro [2H-indole-2,3′-[3H] phenanthr [9,10-b] (1,4) oxazine] (oxazine) into PVA polymer matrix via electrospinning technique. The resultant nanofibers were measured for recording–erasing, photo-coloration and thermal reversibility. The rate of photo-coloration of PVA–indole nanofibers was five times higher than the PVA–oxazine nanofibers, whereas the thermal reversibility found to be more than twice as fast as PVA–oxazine nanofibers. Results showed that the resultant nanofibers have very good capability of recording QR codes multiple times. The FTIR spectroscopy and SEM were employed to characterize the electrospun nanofibers. The UV-responsive PVA nanofibers have great potentials as a light-driven nanomaterials incorporated within sensors, sensitive displays and in optical devices such as erasable and rewritable optical storage.

UV-responsive polyvinyl alcohol nanofibers prepared by electrospinning

International Nuclear Information System (INIS)

Khatri, Zeeshan; Ali, Shamshad; Khatri, Imran; Mayakrishnan, Gopiraman; Kim, Seong Hun; Kim, Ick-Soo

2015-01-01

Graphical abstract: - Highlights: • UV responsive PVA nanofibers were prepared via electrospinning. • Quick response codes were recorded multiple times on UV responsive nanofibers. • The rate of photo-coloration was found faster than the rate of photo-reversibility. - Abstract: We report UV-responsive polyvinyl alcohol (PVA) nanofibers for potential application for recording and erasing quick response (QR) codes. We incorporate 1′-3′-dihydro-8-methoxy-1′,3′,3′-trimethyl-6-nitrospiro [2H-1-benzopyran-2,2′-(2H)-indole] (indole) and,3-dihydro-1,3,3-trimethylspiro [2H-indole-2,3′-[3H] phenanthr [9,10-b] (1,4) oxazine] (oxazine) into PVA polymer matrix via electrospinning technique. The resultant nanofibers were measured for recording–erasing, photo-coloration and thermal reversibility. The rate of photo-coloration of PVA–indole nanofibers was five times higher than the PVA–oxazine nanofibers, whereas the thermal reversibility found to be more than twice as fast as PVA–oxazine nanofibers. Results showed that the resultant nanofibers have very good capability of recording QR codes multiple times. The FTIR spectroscopy and SEM were employed to characterize the electrospun nanofibers. The UV-responsive PVA nanofibers have great potentials as a light-driven nanomaterials incorporated within sensors, sensitive displays and in optical devices such as erasable and rewritable optical storage

Fabrication and EMI shielding effectiveness of Ag-decorated highly porous poly(vinyl alcohol)/Fe2O3 nanofibrous composites

International Nuclear Information System (INIS)

Kim, Hae-Rim; Kim, Byoung-Suhk; Kim, Ick-Soo

2012-01-01

The Ag-decorated poly(vinyl alcohol) (PVA) composite nanofibrous webs incorporating Fe 2 O 3 nanoparticles were fabricated by electrospinning and metal-deposition methods for electromagnetic interference (EMI) shielding applications. The Ag-decorated PVA/Fe 2 O 3 composite nanofiber webs with various Ag thicknesses and different amounts of Fe 2 O 3 nanoparticles were prepared and used for EMI shielding measurement. For the EMI SE measurement, a near-field antenna measurement system was used. The measurement of EMI SE was carried out at the frequency range from 0.5 to 18 GHz, and the electromagnetic parameters were measured. The morphologies and microstructures of the resultant PVA/Fe 2 O 3 composite nanofiber webs were characterized using field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM), respectively. The effects of surface morphologies and Fe 2 O 3 nanoparticles on the EMI shielding effectiveness of Ag-decorated PVA/Fe 2 O 3 composite nanofiber webs were investigated. -- Highlights: ► We prepare Ag-decorated poly(vinyl alcohol) nanowebs incorporating Fe 2 O 3 nanoparticles. ► Solvents will affect the fiber morphologies and Fe 2 O 3 nanoparticles dispersion. ► EMI shielding effectiveness depends on the metal thickness and Fe 2 O 3 nanoparticles dispersion.

Study of poly(vinyl alcohol)/titanium oxide composite polymer membranes and their application on alkaline direct alcohol fuel cell

Science.gov (United States)

Yang, Chun-Chen; Chiu, Shwu-Jer; Lee, Kuo-Tong; Chien, Wen-Chen; Lin, Che-Tseng; Huang, Ching-An

The novel poly(vinyl alcohol)/titanium oxide (PVA/TiO 2) composite polymer membrane was prepared using a solution casting method. The characteristic properties of the PVA/TiO 2 composite polymer membrane were investigated by thermal gravimetric analysis (TGA), a scanning electron microscopy (SEM), a micro-Raman spectroscopy, a methanol permeability measurement and the AC impedance method. An alkaline direct alcohol (methanol, ethanol and isopropanol) fuel cell (DAFC), consisting of an air cathode based on MnO 2/C inks, an anode based on PtRu (1:1) black and a PVA/TiO 2 composite polymer membrane, was assembled and examined for the first time. The results indicate that the alkaline DAFC comprised of a cheap, non-perfluorinated PVA/TiO 2 composite polymer membrane shows an improved electrochemical performances. The maximum power densities of alkaline DAFCs with 4 M KOH + 2 M CH 3OH, 2 M C 2H 5OH and 2 M isopropanol (IPA) solutions at room temperature and ambient air are 9.25, 8.00, and 5.45 mW cm -2, respectively. As a result, methanol shows the highest maximum power density among three alcohols. The PVA/TiO 2 composite polymer membrane with the permeability values in the order of 10 -7 to 10 -8 cm 2 s -1 is a potential candidate for use on alkaline DAFCs.

Monitoring of temperature fatigue failure mechanism for polyvinyl alcohol fiber concrete using acoustic emission sensors.

Science.gov (United States)

Li, Dongsheng; Cao, Hai

2012-01-01

The applicability of acoustic emission (AE) techniques to monitor the mechanism of evolution of polyvinyl alcohol (PVA) fiber concrete damage under temperature fatigue loading is investigated. Using the temperature fatigue test, real-time AE monitoring data of PVA fiber concrete is achieved. Based on the AE signal characteristics of the whole test process and comparison of AE signals of PVA fiber concretes with different fiber contents, the damage evolution process of PVA fiber concrete is analyzed. Finally, a qualitative evaluation of the damage degree is obtained using the kurtosis index and b-value of AE characteristic parameters. The results obtained using both methods are discussed.

Microstructure and molecular interaction in glycerol plasticized chitosan/poly(vinyl alcohol) blending films

Science.gov (United States)

Poly (vinyl alcohol) (PVA)/chitosan (CS) blended films plasticized by glycerol were investigated using mechanical testing, atomic force microscopy (AFM), differential scanning calorimetry (DSC) and FTIR spectroscopy, with primary emphasis on the effects of the glycerol content and the molecular weig...

Clinical Long-Term Outcome and Reinterventional Rate After Uterine Fibroid Embolization with Nonspherical Versus Spherical Polyvinyl Alcohol Particles

Energy Technology Data Exchange (ETDEWEB)

Duvnjak, Stevo, E-mail: stevo.duvnjak@rsyd.dk [Odense University Hospital, Department of Radiology (Denmark); Ravn, Pernille [Odense University Hospital, Department of Gynecology (Denmark); Green, Anders [Odense University Hospital, Odense Patient Data Explorative Network (Denmark); Andersen, Poul Erik [Odense University Hospital, Department of Radiology (Denmark)

2016-02-15

PurposeThis study was designed to evaluate the long-term clinical outcome and frequency of reinterventions in patients with uterine fibroids treated with embolization at a single center using polyvinyl alcohol microparticles.MethodsThe study included all patients with symptomatic uterine fibroids treated with uterine fibroid embolization (UFE) with spherical (s-PVA) and nonspherical (ns-PVA) polyvinyl alcohol microparticles during the period January 2001 to January 2011. Clinical success and secondary interventions were examined. Hospital records were reviewed during follow-up, and symptom-specific questionnaires were sent to all patients.ResultsIn total, 515 patients were treated with UFE and 350 patients (67 %) were available for long-term clinical follow-up. Median time of follow-up was 93 (range 76–120.2) months. Eighty-five patients (72 %) had no reinterventions during follow-up in the group embolized with ns-PVA compared with 134 patients (58 %) treated with s-PVA. Thirty-three patients (28 %) underwent secondary interventions in the ns-PVA group compared with 98 patients (42 %) in s-PVA group (χ{sup 2} test, p < 0.01).ConclusionsSpherical PVA particles 500–700 µm showed high reintervention rate at long-term follow-up, and almost one quarter of the patients underwent secondary interventions, suggesting that this type of particle is inappropriate for UFE.

Surface modification of polyvinyl alcohol/malonic acid nanofibers by gaseous dielectric barrier discharge plasma for glucose oxidase immobilization

International Nuclear Information System (INIS)

Afshari, Esmail; Mazinani, Saeedeh; Ranaei-Siadat, Seyed-Omid; Ghomi, Hamid

2016-01-01

Highlights: • We fabricated polyvinyl alcohol/malonic acid nanofibers using electrospinning. • The surface nanofibers were modified by gaseous (air, nitrogen, CO_2 and argon) dielectric barrier discharge. • Among them, air plasma had the most significant effect on glucose oxidase immobilization. • Chemical analysis showed that after modification of nanofibers by air plasma, the carboxyl group increased. • After air plasma treatment, reusability and storage stability of glucose oxidase immobilized on nanofibers improved. - Abstract: Polymeric nanofiber prepares a suitable situation for enzyme immobilization for variety of applications. In this research, we have fabricated polyvinyl alcohol (PVA)/malonic acid nanofibers using electrospinning. After fabrication of nanofibers, the effect of air, nitrogen, CO_2, and argon DBD (dielectric barrier discharge) plasmas on PVA/malonic acid nanofibers were analysed. Among them, air plasma had the most significant effect on glucose oxidase (GOx) immobilization. Attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectrum analysis and X-ray photoelectron spectroscopy (XPS) results revealed that in case of air plasma modified nanofibers, the carboxyl groups on the surface are increased. The scanning electron microscopy (SEM) images showed that, after GOx immobilization, the modified nanofibers with plasma has retained its nanofiber structure. Finally, we analysed reusability and storage stability of GOx immobilized on plasma modified and unmodified nanofibers. The results were more satisfactory for modified nanofibers with respect to unmodified ones.

Surface modification of polyvinyl alcohol/malonic acid nanofibers by gaseous dielectric barrier discharge plasma for glucose oxidase immobilization

Energy Technology Data Exchange (ETDEWEB)

Afshari, Esmail, E-mail: e.afshari@mail.sbu.ac.ir [Laser and Plasma Research Institute, Shahid Beheshti University, Evin, 1983963113 Tehran (Iran, Islamic Republic of); Mazinani, Saeedeh [Amirkabir Nanotechnology Research Institute (ANTRI), Amirkabir University of Technology, 15875-4413, Tehran (Iran, Islamic Republic of); Ranaei-Siadat, Seyed-Omid [Protein Research Center, Shahid Beheshti University, Evin, 1983963113 Tehran (Iran, Islamic Republic of); Ghomi, Hamid [Laser and Plasma Research Institute, Shahid Beheshti University, Evin, 1983963113 Tehran (Iran, Islamic Republic of)

2016-11-01

Highlights: • We fabricated polyvinyl alcohol/malonic acid nanofibers using electrospinning. • The surface nanofibers were modified by gaseous (air, nitrogen, CO{sub 2} and argon) dielectric barrier discharge. • Among them, air plasma had the most significant effect on glucose oxidase immobilization. • Chemical analysis showed that after modification of nanofibers by air plasma, the carboxyl group increased. • After air plasma treatment, reusability and storage stability of glucose oxidase immobilized on nanofibers improved. - Abstract: Polymeric nanofiber prepares a suitable situation for enzyme immobilization for variety of applications. In this research, we have fabricated polyvinyl alcohol (PVA)/malonic acid nanofibers using electrospinning. After fabrication of nanofibers, the effect of air, nitrogen, CO{sub 2}, and argon DBD (dielectric barrier discharge) plasmas on PVA/malonic acid nanofibers were analysed. Among them, air plasma had the most significant effect on glucose oxidase (GOx) immobilization. Attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectrum analysis and X-ray photoelectron spectroscopy (XPS) results revealed that in case of air plasma modified nanofibers, the carboxyl groups on the surface are increased. The scanning electron microscopy (SEM) images showed that, after GOx immobilization, the modified nanofibers with plasma has retained its nanofiber structure. Finally, we analysed reusability and storage stability of GOx immobilized on plasma modified and unmodified nanofibers. The results were more satisfactory for modified nanofibers with respect to unmodified ones.

Fabrication of α-chitin whisker-reinforced poly(vinyl alcohol) nanocomposite nanofibres by electrospinning

International Nuclear Information System (INIS)

Junkasem, Jirawut; Rujiravanit, Ratana; Supaphol, Pitt

2006-01-01

The present contribution reports, for the first time, the successful fabrication of α-chitin whisker-reinforced poly(vinyl alcohol) (PVA) nanocomposite nanofibres by electrospinning. The α-chitin whiskers were prepared from α-chitin flakes from shrimp shells by acid hydrolysis. The as-prepared chitin whiskers exhibited lengths in the range 231-969 nm and widths in the range 12-65 nm, with the average length and width being about 549 and 31 nm, respectively. Successful incorporation of the chitin whiskers within the as-spun PVA/chitin whisker nanocomposite nanofibres was verified by infrared spectroscopic and thermogravimetric methods. The incorporation of chitin whiskers within the as-spun nanocomposite fibre mats increased the Young's modulus by about 4-8 times over that of the neat as-spun PVA fibre mat

A study of poly(vinyl alcohol thermal degradation by thermogravimetry and differential thermogravimetry

Directory of Open Access Journals (Sweden)

Julián Esteban Barrera

2007-05-01

Full Text Available The thermal degradation of poly(vinyl alcohol (PVA having different degrees of hydrolysis and molecular weights was studied by thermogravimetry (TGA and differential thermogravimetry (DTGA. Four degradation events were identified whose intensity was related to the degree of hydrolysis. It was verified that the solid-state degradation mechanism for high hydrolysis degrees corresponded to eliminating water-forming side groups in stoichiometric amounts. The presence of acetate groups and lower melting points delayed the polymer’s thermal decomposition at lower hydrolysis degrees. There was no direct correlation in these samples between weight-loss during the first degradation event and the stoichiometric quantities which would be produced by eliminating the side groups. Reaction order and energy activation value qualitative coincidence was found by evaluating experimental data by using Freeman-Carroll and Friedman kinetic models.

Piezoresistive Pressure Sensor Based on Synergistical Innerconnect Polyvinyl Alcohol Nanowires/Wrinkled Graphene Film.

Science.gov (United States)

Liu, Weijie; Liu, Nishuang; Yue, Yang; Rao, Jiangyu; Cheng, Feng; Su, Jun; Liu, Zhitian; Gao, Yihua

2018-04-01

Piezoresistive sensor is a promising pressure sensor due to its attractive advantages including uncomplicated signal collection, simple manufacture, economical and practical characteristics. Here, a flexible and highly sensitive pressure sensor based on wrinkled graphene film (WGF)/innerconnected polyvinyl alcohol (PVA) nanowires/interdigital electrodes is fabricated. Due to the synergistic effect between WGF and innerconnected PVA nanowires, the as-prepared pressure sensor realizes a high sensitivity of 28.34 kPa -1 . In addition, the device is able to discern lightweight rice about 22.4 mg (≈2.24 Pa) and shows excellent durability and reliability after 6000 repeated loading and unloading cycles. What is more, the device can detect subtle pulse beat and monitor various human movement behaviors in real-time. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Change Spectroscopic, thermal and mechanical studies of PU/PVC blends

Energy Technology Data Exchange (ETDEWEB)

Hezma, A.M. [Spectroscopy Department, Physics Division, National Research Center, Giza (Egypt); Elashmawi, I.S. [Spectroscopy Department, Physics Division, National Research Center, Giza (Egypt); Physic Department, Faculty of Science, Taibah University, Al-Ula (Saudi Arabia); Rajeh, A., E-mail: a.rajeh88@yahoo.com [Physic Department, Faculty of Science, Amran University, Sa' dah (Yemen); Physics Department, Faculty of science, Mansoura University, Mansoura (Egypt); Kamal, Mustafa [Physics Department, Faculty of science, Mansoura University, Mansoura (Egypt)

2016-08-15

Blends of polyurethane (PU) and polyvinyl chloride (PVC) with different concentrations were prepared by casting method. The effects of PU on PVC blends was examined by Fourier transform-infrared (FTIR), Ultra-violet visible studies (UV/VIS.), X-ray diffraction (XRD), Thermogravimetric (TGA), Differential scanning calorimetry (DSC), and mechanical properties (stress–strain curve). The interaction between PU and PVC was examined by FT-IR through the absorbance of the N–H groups and was correlated to mechanical/thermal properties. Ultra-violet visible said that optical energy gap decrease with increasing concentration of PU. Differential scanning calorimetry results was observed a single glass transition temperature (T{sub g}) for blends this confirming existence miscibility within the blends. The causes for best thermal stability of some blends may be described by measurements of interactions between C=O groups of PU and the α-hydrogen of PVC or a dipole–dipole –C=O..Cl–C– interactions. Significant alterations in FTIR, X-ray and DSC examination shows an interactions between blends had good miscibility. X-ray shows some alterations in the intensity with additional PU. PU change the mechanical behavior of PVC through of the blends. When polyurethane content increase causes polyvinyl chloride tensile strength decreases and elongation at break increase.

Low frequency dielectric relaxation processes and ionic conductivity of montmorillonite clay nanoparticles colloidal suspension in poly(vinyl pyrrolidone−ethylene glycol blends

Directory of Open Access Journals (Sweden)

2008-11-01

Full Text Available The dielectric dispersion behaviour of montmorillonite (MMT clay nanoparticles colloidal suspension in poly(vinyl pyrrolidone-ethylene glycol (PVP-EG blends were investigated over the frequency range 20 Hz to 1 MHz at 30°C. The 0, 1, 2, 3, 5 and 10 wt% MMT clay concentration of the weight of total solute (MMT+PVP were prepared in PVP-EG blends using EG as solvent. The complex relative dielectric function, alternating current (ac electrical conductivity, electric modulus and impedance spectra of these materials show the relaxation processes corresponding to the micro-Brownian motion of PVP chain, ion conduction and electrode polarization phenomena. The real part of ac conductivity spectra of these materials obeys Jonscher power law σ′(ω =σdc + Aωn in upper frequency end of the measurement, whereas dispersion in lower frequency end confirms the presence of electrode polarization effect. It was observed that the increase of clay concentration in the PVP-EG blends significantly increases the ac conductivity values, and simultaneously reduces the ionic conductivity relaxation time and electric double layer relaxation time, which suggests that PVP segmental dynamics and ionic motion are strongly coupled. The intercalation of EG structures in clay galleries and exfoliation of clay sheets by adsorption of PVP-EG structures on clay surfaces are discussed by considering the hydrogen bonding interactions between the hydroxyl group (–OH of EG molecules, carbonyl group (C=O of PVP monomer units, and the hydroxylated aluminate surfaces of the MMT clay particles. Results suggest that the colloidal suspension of MMT clay nano particles in the PVP-EG blends provide a convenient way to obtain an electrolyte solution with tailored electrical conduction properties.

Polyvinyl alcohol-immobilized Phanerochaete chrysosporium and its application in the bioremediation of composite-polluted wastewater

Energy Technology Data Exchange (ETDEWEB)

Huang, Zhenzhen [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Chen, Guiqiu, E-mail: gqchen@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Zeng, Guangming, E-mail: zgming@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Chen, Anwei [College of Resources and Environment, Hunan Agricultural University, Changsha 410128 (China); Zuo, Yanan; Guo, Zhi; Tan, Qiong [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Song, Zhongxian [Faculty of Environmental Science and Engineering, Kunming University of Science and Technology, Kunming 650500 (China); Niu, Qiuya [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China)

2015-05-30

Graphical abstract: Schematic diagram of polyvinyl alcohol-immobilized Phanerochaete chrysosporium beads (PPBs) for Cd(II) removal and 2,4-DCP degradation. - Highlights: • PVA-immobilized P. chrysosporium beads (PPBs) were fit for wastewater treatment. • Removal rates of Cd(II) and 2,4-DCP at optimum conditions were up to 78% and 95.4%. • 2,4-DCP removal rates were beyond 90% with varying initial 2,4-DCP concentrations. • PVA was vital to Cd(II) removal besides the function groups in P. chrysosporium. • Maximum recovery of the Cd(II)-laden PPBs after reuse three times was 98.9%. - Abstract: A novel biosorbent, polyvinyl alcohol (PVA)-immobilized Phanerochaete chrysosporium, was applied to the bioremediation of composite-polluted wastewater, containing both cadmium and 2,4-dichlorophenol (2,4-DCP). The optimum removal efficiency achieved was 78% for Cd(II) and 95.4% for 2,4-DCP at initial concentrations of 20 mg/L Cd(II) and 40 mg/L 2,4-DCP. PPBs had significantly enhanced the resistance of P. chrysosporium to 2,4-DCP, leading to the degradation rates of 2,4-DCP beyond 90% with varying initial 2,4-DCP concentrations. This research demonstrated that 2,4-DCP and secreted proteins might be used as carbon and nitrogen sources by PVA-immobilized P. chrysosporium beads (PPBs) for Cd(II) removal. Fourier transform infrared spectroscopy analysis showed that hydroxyl and carboxyl groups on the surface of PPBs were dominant in Cd(II) binding. The mechanism underlying the degradation of 2,4-DCP into fumaric acid and 1-hexanol was investigated. The adsorption–desorption studies indicated that PPBs kept up to 98.9% of desorption efficiency over three cycles.

Polyvinyl alcohol-immobilized Phanerochaete chrysosporium and its application in the bioremediation of composite-polluted wastewater

International Nuclear Information System (INIS)

Huang, Zhenzhen; Chen, Guiqiu; Zeng, Guangming; Chen, Anwei; Zuo, Yanan; Guo, Zhi; Tan, Qiong; Song, Zhongxian; Niu, Qiuya

2015-01-01

Graphical abstract: Schematic diagram of polyvinyl alcohol-immobilized Phanerochaete chrysosporium beads (PPBs) for Cd(II) removal and 2,4-DCP degradation. - Highlights: • PVA-immobilized P. chrysosporium beads (PPBs) were fit for wastewater treatment. • Removal rates of Cd(II) and 2,4-DCP at optimum conditions were up to 78% and 95.4%. • 2,4-DCP removal rates were beyond 90% with varying initial 2,4-DCP concentrations. • PVA was vital to Cd(II) removal besides the function groups in P. chrysosporium. • Maximum recovery of the Cd(II)-laden PPBs after reuse three times was 98.9%. - Abstract: A novel biosorbent, polyvinyl alcohol (PVA)-immobilized Phanerochaete chrysosporium, was applied to the bioremediation of composite-polluted wastewater, containing both cadmium and 2,4-dichlorophenol (2,4-DCP). The optimum removal efficiency achieved was 78% for Cd(II) and 95.4% for 2,4-DCP at initial concentrations of 20 mg/L Cd(II) and 40 mg/L 2,4-DCP. PPBs had significantly enhanced the resistance of P. chrysosporium to 2,4-DCP, leading to the degradation rates of 2,4-DCP beyond 90% with varying initial 2,4-DCP concentrations. This research demonstrated that 2,4-DCP and secreted proteins might be used as carbon and nitrogen sources by PVA-immobilized P. chrysosporium beads (PPBs) for Cd(II) removal. Fourier transform infrared spectroscopy analysis showed that hydroxyl and carboxyl groups on the surface of PPBs were dominant in Cd(II) binding. The mechanism underlying the degradation of 2,4-DCP into fumaric acid and 1-hexanol was investigated. The adsorption–desorption studies indicated that PPBs kept up to 98.9% of desorption efficiency over three cycles

Adsorption Characteristics of Polyvinyl Alcohols in Solution on Expanded Graphite

Directory of Open Access Journals (Sweden)

Xiu-Yan Pang

2012-01-01

Full Text Available Expanded graphite (EG adsorbent was prepared with 50 mesh graphite as raw materials, potassium permanganate as oxidant, and vitriol as intercalation compound. Three kinds of polyvinyl alcohol (PVA with different degree of polymerization (DP in aqueous solution were used as adsorbates. We have studied the influence of initial PVA concentration, temperature and ionic strength on adsorption capacity. Langmuir constants and Gibbs free energy change (⊿G° were calculated according to experimental data respectively. Thermodynamic analysis indicates the equilibrium adsorbance of PVA on EG increase with the rise of SO42– concentration. Adsorption isotherms of PVA with different degree of polymerization are all types and we deduce PVA molecules lie flat on EG surface. Adsorption processes are all spontaneous. Kinetic studies show that the kinetic data can be described by pseudo second-order kinetic model. Second-order rate constants and the initial adsorption rate rise with the increasing of temperature and half-adsorption time decreases with the increasing of temperature. The adsorption activation energy of each PVA is less than 20 kJ•mol−1, physical adsorption is the major mode of the overall adsorption process.

Research progress of fabricating polyvinyl alcohol coating on plastic microsphere

International Nuclear Information System (INIS)

Su Lin; Chen Sufen; Liu Meifang; Zhang Zhanwen; Yao Hong; Li Bo; Liu Yiyang

2012-01-01

In the procedures of designing polystyrene-polyvinyl alcohol-CH (carbon and hydrogen elements) (PS-PVA-CH) triple-layer microspheres, there are many methods such as drop-tower technique, emulsion micro-encapsulation, dip (spin) coating, interfacial polycondensation, and spraying technique to prepare the PVA coating. Drop-tower technique, emulsion micro-encapsulation and dip (spin) coating are most-commonly used. The advantages, disadvantages and the research progress of the three methods are summarized in this paper. Emulsion micro-encapsulation is suitable for preparing double-layer microspheres of sizes smaller then 500 μm, with high survival ratio and good quality. However, the preparation process is easily influenced by artificial factors. Small-sized double-layer microspheres can also be prepared by the drop-tower technique, and the preparation period is short. But there are still some problems such as the difficulty in designing the droplet generator, uneven PVA coating and the difficulty in preparing large-sized microspheres. Dip (spin) coating technique can be used to prepare PS-PVA microspheres with sizes larger than 1000 μm, but the spread of PVA coating is affected by many factors in this method, and the prepared PVA coating is too thin and not uniform. (authors)

Tailoring of poly(vinyl alcohol cryogels properties by salts addition

Directory of Open Access Journals (Sweden)

2009-05-01

Full Text Available The present paper aims to study the possibility to modify the properties of poly(vinyl alcohol (PVA hydrogels prepared in the presence of different salt types (Na2SO4, NaCl and NaNO3 in order to extend the nature of the salts already used in obtaining films or gels, to expand their concentration domains and to explain the increase of film strain, concomitantly with the increase of their crystallinity. The morphology of the PVA based hydrogels has been studied by Scanning Electronic Microscopy (SEM, the interaction between the PVA macromolecular chains and salts has been determined by Fourier Transform Infrared Spectroscopy (FTIR, while the mechanical properties of the cryogels have been investigated by oscillatory dynamic mechanical measurements. The gels swelling in water have been monitored by gravimetric method in order to evidence the alteration of the PVA cryogel properties such as crystallinity and porosity determined by the salt addition to the initial PVA aqueous solution. The data reported show that the ions present in the PVA solution influence the interaction between PVA-water and PVA-PVA chains; their influence on the salt-based PVA hydrogels follow the Hofmeister lyotropic series.

Development and Evaluation of Polyvinyl Alcohol-Hydrogels as an Artificial Atrticular Cartilage for Orthopedic Implants

Directory of Open Access Journals (Sweden)

Masanori Kobayashi

2010-04-01

Full Text Available Due to its excellent biocompatibility and mechanical properties, various different applications of polyvinyl alcohol-hydrogels (PVA-H has been attempted in many fields. In the field of orthopedic surgery, we have been engaged for long time in research on the clinical applications of PVA-H as a artificial cartilage, and have performed many basic experiments on the mechanical properties, synthesis of PVA-H, and developed orthopedic implants using PVA-H. From these studies, many applications of artificial articular cartilage, intervertbral disc and artificial meniscus etc. have been developed. This review will present the overview of the applications and recent advances of PVA-H cartilages, and discuss clinical potential of PVA-H for orthopedics implant.

Development and Evaluation of Polyvinyl Alcohol-Hydrogels as an Artificial Atrticular Cartilage for Orthopedic Implants

Science.gov (United States)

Kobayashi, Masanori; Hyu, Hyon Suong

2010-01-01

Due to its excellent biocompatibility and mechanical properties, various different applications of polyvinyl alcohol-hydrogels (PVA-H) has been attempted in many fields. In the field of orthopedic surgery, we have been engaged for long time in research on the clinical applications of PVA-H as a artificial cartilage, and have performed many basic experiments on the mechanical properties, synthesis of PVA-H, and developed orthopedic implants using PVA-H. From these studies, many applications of artificial articular cartilage, intervertbral disc and artificial meniscus etc. have been developed. This review will present the overview of the applications and recent advances of PVA-H cartilages, and discuss clinical potential of PVA-H for orthopedics implant.

The use of polyvinyl alcohol glutaraldehyde as solid-phase in ELISA for plague

Directory of Open Access Journals (Sweden)

Aureci Maria Araujo

1996-04-01

Full Text Available Discs of polyvinyl alcohol cross-linked with glutaraldehyde were synthesized under acid catalysis (H2SO4. Then, the antigen F1 purified from Yersinia pestis was covalently linked to this modified polymer. Afterwards, an enzyme-linked immunosorbent assay (ELISA was established for the diagnosis of plague in rabbit and human. The best conditions for the method were achieved by using 1.3 ¼g of F1 prepared in 0.067 M phosphate buffer, pH 7.2, containing 1 M NaCl (PBS; anti-IgG peroxidase conjugate diluted 6,000 times and as a blocking agent 3% w/v skim milk in PBS. The titration of positive rabbit serum according to this procedure detected antibody concentrations up to 1:12,800 times. The present method, the conventional ELISA and passive haemagglutination assay are compared.

Investigation of Electrical and Optical Characteristics of Nanohybride Composite (Polyvinyl Alcohol / Nickel Oxide

Directory of Open Access Journals (Sweden)

A. Hayati

2014-01-01

Full Text Available Some issues; leakage, tunneling currents, boron diffusion are threatening SiO2 to be used as a good gate dielectric for the future of the CMOS (complementary metal- oxide- semiconductor transistors. For finding an alternative and novel gate dielectric, the NiO (Nickel oxide and PVA (polyvinyl alcohol nano powders were synthesized with the sol-gel method and their nano structural properties were studied using the X-ray diffraction (XRD, Atomic force microscopy (AFM, Scanning electron microscopy (SEM, UV-Vis spectrophotometer and GPS 132 techniques. The obtained results indicated that the sample (5 g NiO and 0.02g PVA prepared at 30˚C, annealed in an oven at a temperature of 80˚C can fill this gap due to its higher dielectric constant, better morphology, less rough surface and less leakage current.

Metal Oxides Doped PPY-PVA Blend Thin Films Based Gas Sensor

Directory of Open Access Journals (Sweden)

D. B. DUPARE

2009-02-01

Full Text Available Synthesis of metal oxides doped polypyrrole–polyvinyl alcohol blend thin films by in situ chemical oxidative polymerization, using microwave oven on glass substrate for development of Ammonia and Trimethyl ammine hazardous gas sensor. The all experimental process carried out at room temperature(304 K. These polymer materials were characterized by Chemical analyses, spectral studies (UV-visible and IR and conductivity measurement by four –probe technique. The surface morphology as observed in the SEM image was observed to be uniformly covering the entire substrate surface. The sensor was used for different concentration (ppm of TMA and Ammonia gas investigation at room temperature (304 k. This study found to possess improved electrical, mechanical and environmental stability metal oxides doped PPY-PVA films.

PEO + PVP blended polymer composite

Indian Academy of Sciences (India)

Blended polymer films of polyethylene oxide + polyvinyl pyrrolidone (PEO + PVP) containing transition metal (TM) ions like Fe3+, Co2+ and Ni2+ have been synthesized by a solution casting method. For these films, structural, thermal, magnetic and optical properties have been studied. X-ray diffraction results reveal the ...

Electrospun single-walled carbon nanotube/polyvinyl alcohol composite nanofibers: structure-property relationships

International Nuclear Information System (INIS)

Naebe, Minoo; Lin Tong; Wang Xungai; Staiger, Mark P; Dai Liming

2008-01-01

Polyvinyl alcohol (PVA) nanofibers and single-walled carbon nanotube (SWNT)/PVA composite nanofibers have been produced by electrospinning. An apparent increase in the PVA crystallinity with a concomitant change in its main crystalline phase and a reduction in the crystalline domain size were observed in the SWNT/PVA composite nanofibers, indicating the occurrence of a SWNT-induced nucleation crystallization of the PVA phase. Both the pure PVA and SWNT/PVA composite nanofibers were subjected to the following post-electrospinning treatments: (i) soaking in methanol to increase the PVA crystallinity, and (ii) cross-linking with glutaric dialdehyde to control the PVA morphology. Effects of the PVA morphology on the tensile properties of the resultant electrospun nanofibers were examined. Dynamic mechanical thermal analyses of both pure PVA and SWNT/PVA composite electrospun nanofibers indicated that SWNT-polymer interaction facilitated the formation of crystalline domains, which can be further enhanced by soaking the nanofiber in methanol and/or cross-linking the polymer with glutaric dialdehyde

Thermal, mechanical and dielectric properties of poly(vinyl alcohol)/graphene oxide composites

Science.gov (United States)

Rathod, Sunil G.; Bhajantri, R. F.; Ravindrachary, V.; Pujari, P. K.; Sheela, T.; Naik, Jagadish

2014-04-01

In this work the composite films of poly(vinyl alcohol) (PVA) doped with functionalized Graphene Oxide (GO) were prepared by solution casting method. The films were characterized using FT-IR, DSC, XRD, mechanical properties and dielectric studies at room temperature. FTIR spectra shows the formation of hydrogen bonds between hydroxyl groups of PVA and the hydroxy groups of GO. The DSC thermograms shows the addition of GO to PVA greatly improves the thermal stability of the composites. XRD patterns shows that the GO exfoliated and uniformly dispersed in PVA matrix. Mechanical properties are significantly improved in PVA/GO composites. The tensile strength increased from 8.2 to 13.7 MPa and the Young's modulus increased from 7.5 to 24.8 MPa for 5 wt% GO doped sample. Dielectric spectroscopy showed a highest dielectric constant for the 5 wt% GO doped PVA films. This work provides a potential design strategy on PVA/GO composite, which would lead to higher-performance, flexible dielectric materials, high charge-storage devices.

Low-temperature-cured highly conductive composite of Ag nanowires and polyvinyl alcohol

International Nuclear Information System (INIS)

He Song; Zhang Xiang; Yang Bingchu; Xu Xiaomei; Chen Hui; Zhou Conghua

2017-01-01

Flexible conductive films were fabricated from a low-temperature-cured, highly conductive composite of silver nanowires (as conducting filler) and polyvinyl alcohol (PVA, as binder). Sheet resistance of 0.12 Ω/sq, conductivity of 2.63×10 4 S/cm, and contact resistance of 1.0 Ω/cm 2 were measured in the films, along with excellent resistance to scratching and good flexibility, making them suitable electrical contact materials for flexible optoelectronic devices. Effects of curing temperature, curing duration, film thickness, and nanowire length on the film’s electrical properties were studied. Due to the abundance of hydroxyl groups on its molecular chains, the addition of PVA improves the film’s flexibility and resistance to scratching. Increased nanowire density and nanowire length benefit film conductance. Monte Carlo simulation was used to further explore the impact of these two parameters on the conductivity. It was observed that longer nanowires produce a higher length-ratio of conducting routes in the networks, giving better film conductivity. (paper)

Nanofibers obtained by electrospinning of BaTiO3 particles dispersed in polyvinyl alcohol and ethylcellulose

Energy Technology Data Exchange (ETDEWEB)

Avila, Humar A.; Reboredo, Maria M.; Castro, Miriam; Parra, Rodrigo, E-mail: havila@fi.mdp.edu.ar [Instituto de Investigaciones en Ciencia y Tecnologia de Materiales - INTEMA, Consejo Nacional de Investigaciones Cientificas y Tecnicas - CONICET, Universidad Nacional de Mar del Plata - UNMdP, Mar del Plata (Argentina)

2013-11-01

Barium titanate particles (100-300 nm) synthesized by hydrothermal method were dispersed in both polyvinyl alcohol (PVA) and ethylcellulose (EC) solutions. These suspensions were processed by electrospinning. When no particles were added, homogeneous polymeric nanofibers were obtained. Under certain conditions, polymeric suspensions of barium titanate particles were electrospun generating polymeric fibers with BT particles. The effect of a surfactant was also assessed over the formation of nanofibers. The BaTiO{sub 3} particles synthesized by hydrothermal method were characterized by X-Ray diffraction (XRD), field emission-scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and Raman spectroscopy. Fibers were characterized by scanning electron microscopy (SEM). (author)

Time-dependent micro-Raman scattering studies of polyvinyl ...

Indian Academy of Sciences (India)

2014-02-15

Feb 15, 2014 ... Micro-Raman scattering; surface plasmons; silver nanoparticles; polyvinyl alcohol. PACS Nos 74.25.nd; ... as well as their characterization. Added .... 3.2 Surface plasmon absorption of thin films of PVA + AgNO3. The surface ...

Controlled synthesis of novel 3D dendritic Bi2S3 /cross-linked poly(vinyl alcohol) nanocomposites

International Nuclear Information System (INIS)

Wu, W-T; Shi Lei; Pang Wenmin; Wang Yusong; Zhu Qingren; Xu Guoyong

2006-01-01

Novel spherical three-dimensional (3D) dendritic Bi 2 S 3 /cross-linked poly(vinyl alcohol) (PVA) nanocomposites were successfully synthesized in aqueous solution of amphiphilic polyvinylacetone (PVKA) (ketalization degree D H = 0.549), via one-step in situ decomposition of the complex [Bi(Tu) x ] 3+ under γ-ray irradiation, utilizing the controllable hydrolysis property of PVKA in acidic solution. Herein, PVA chains are obtained from the hydrolysed PVKA. These uniform 3D spherical nanocomposites have a structure similar to that found in the natural lotus leaf, where every microscale papilla on the leaf surface is covered by nanoscale papillae

AC-conductance and capacitance measurements for ethanol vapor detection using carbon nanotube-polyvinyl alcohol composite based devices.

Science.gov (United States)

Greenshields, Márcia W C C; Meruvia, Michelle S; Hümmelgen, Ivo A; Coville, Neil J; Mhlanga, Sabelo D; Ceragioli, Helder J; Quispe, Jose C Rojas; Baranauskas, Vitor

2011-03-01

We report the preparation of inexpensive ethanol sensor devices using multiwalled carbon nanotube-polyvinyl alcohol composite films deposited onto interdigitated electrodes patterned on phenolite substrates. We investigate the frequency dependent response of the device conductance and capacitance showing that higher sensitivity is obtained at higher frequency if the conductance is used as sensing parameter. In the case of capacitance measurements, higher sensitivity is obtained at low frequency. Ethanol detection at a concentration of 300 ppm in air is demonstrated. More than 80% of the sensor conductance and capacitance variation response occurs in less than 20 s.

A comparative analysis on combustion and emissions of some next generation higher-alcohol/diesel blends in a direct-injection diesel engine

International Nuclear Information System (INIS)

Rajesh Kumar, B.; Saravanan, S.; Rana, D.; Nagendran, A.

2016-01-01

Highlights: • Four higher-alcohols namely, iso-butanol, n-pentanol, n-hexanol and n-octanol, were used. • Iso-butanol/diesel blend presented longest ignition delay, highest peak pressures and peak heat release rates. • NOx emissions were high for n-pentanol/diesel and n-hexanol/diesel blends at high load conditions. • Smoke opacity is highest for n-octanol/diesel blend and lowest for iso-butanol/diesel blend. • HC emissions are high for iso-butanol/diesel and n-pentanol/diesel blends. - Abstract: Higher alcohols are attractive next generation biofuels that can be extracted from sugary, starchy and ligno-cellulosic biomass feedstocks using sustainable pathways. Their viability for use in diesel engines has greatly improved ever since extended bio-synthetic pathways have achieved substantial yields of these alcohols using engineered micro-organisms. This study sets out to compare and analyze the effects of some higher alcohol/diesel blends on combustion and emission characteristics of a direct-injection diesel engine. Four test fuels containing 30% by vol. of iso-butanol, n-pentanol, n-hexanol and n-octanol (designated as ISB30, PEN30, HEX30 and OCT30 respectively) in ultra-low sulfur diesel (ULSD) were used. Results indicated that ISB30 experienced longest ignition delay and produced highest peaks of pressure and heat release rates (HRR) compared to other higher-alcohol blends. The ignition delay, peak pressure and peak HRR are found to be in the order of (from highest to lowest): ISB30 > PEN30 > HEX30 > OCT30 > ULSD. The combustion duration (CD) for all test fuels is in the sequence (from shortest to longest): ISB30 OCT30 > HEX30 > PEN30 > ISB30. HC emissions are high for ISB30 and PEN30 while it decreased favorably for HEX30 and OCT30. It was of the order (from highest to lowest): ISB30 > PEN30 > ULSD > HEX30 > OCT30. CO emissions of the blends followed the trend of smoke emissions and remained lower than ULSD with the following order (from highest to

Fabrication of antibacterial blend film from poly (vinyl alcohol) and quaternized chitosan for packaging

Energy Technology Data Exchange (ETDEWEB)

Hu, Dongying; Wang, Lijuan, E-mail: donglinwlj@163.com

2016-06-15

Highlights: • HTCC/PVA blend films were prepared through a simple mixing method. • The blend films had greater elongation at break and good optical transmittance. • The blend films had low oxygen permeability and water vapor permeability. • The films had good activity against Escherichia coli and Staphylococcus aureus. - Abstract: Blend films from poly (vinyl alcohol) (PVA) containing N-(2-hydroxy) propyl-3-trimethyl ammonium chloride chitosan (HTCC) were prepared via a simple mixing and casting method. The films were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction measurements (XRD), scanning electron microscopy and ultraviolet-visible measurements (UV–vis). The effects of HTCC amount on mechanical properties, oxygen permeability, water vapor permeation, and antibacterial properties against Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus) of the films were investigated. FTIR and XRD analysis show that HTCC and PVA in the blend films interacted by hydrogen bonding. SEM and UV–vis analysis reveal the good compatibility between HTCC and PVA. Compared with pure PVA film, the blend films had greater elongation at break, lower water permeability, and higher antibacterial activity. The HTCC addition decreased the tensile strength and the light transmittance. The results suggest that HTCC/PVA blend films have a potential as packaging materials.

Fabrication of antibacterial blend film from poly (vinyl alcohol) and quaternized chitosan for packaging

International Nuclear Information System (INIS)

Hu, Dongying; Wang, Lijuan

2016-01-01

Highlights: • HTCC/PVA blend films were prepared through a simple mixing method. • The blend films had greater elongation at break and good optical transmittance. • The blend films had low oxygen permeability and water vapor permeability. • The films had good activity against Escherichia coli and Staphylococcus aureus. - Abstract: Blend films from poly (vinyl alcohol) (PVA) containing N-(2-hydroxy) propyl-3-trimethyl ammonium chloride chitosan (HTCC) were prepared via a simple mixing and casting method. The films were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction measurements (XRD), scanning electron microscopy and ultraviolet-visible measurements (UV–vis). The effects of HTCC amount on mechanical properties, oxygen permeability, water vapor permeation, and antibacterial properties against Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus) of the films were investigated. FTIR and XRD analysis show that HTCC and PVA in the blend films interacted by hydrogen bonding. SEM and UV–vis analysis reveal the good compatibility between HTCC and PVA. Compared with pure PVA film, the blend films had greater elongation at break, lower water permeability, and higher antibacterial activity. The HTCC addition decreased the tensile strength and the light transmittance. The results suggest that HTCC/PVA blend films have a potential as packaging materials.

Properties and Applications of Polyvinyl Alcohol, Halloysite Nanotubes and Their Nanocomposites

Directory of Open Access Journals (Sweden)

Tayser Sumer Gaaz

2015-12-01

Full Text Available The aim of this review was to analyze/investigate the synthesis, properties, and applications of polyvinyl alcohol–halloysite nanotubes (PVA–HNT, and their nanocomposites. Different polymers with versatile properties are attractive because of their introduction and potential uses in many fields. Synthetic polymers, such as PVA, natural polymers like alginate, starch, chitosan, or any material with these components have prominent status as important and degradable materials with biocompatibility properties. These materials have been developed in the 1980s and are remarkable because of their recyclability and consideration of the natural continuation of their physical and chemical properties. The fabrication of PVA–HNT nanocomposites can be a potential way to address some of PVA’s limitations. Such nanocomposites have excellent mechanical properties and thermal stability. PVA–HNT nanocomposites have been reported earlier, but without proper HNT individualization and PVA modifications. The properties of PVA–HNT for medicinal and biomedical use are attracting an increasing amount of attention for medical applications, such as wound dressings, drug delivery, targeted-tissue transportation systems, and soft biomaterial implants. The demand for alternative polymeric medical devices has also increased substantially around the world. This paper reviews individualized HNT addition along with crosslinking of PVA for various biomedical applications that have been previously reported in literature, thereby showing the attainability, modification of characteristics, and goals underlying the blending process with PVA.

Design of the Elastic Modulus of Nanoparticles-Containing PVA/PVAc Films by the Response Surface Method

Science.gov (United States)

Jelinska, N.; Kalnins, M.; Kovalovs, A.; Chate, A.

2015-11-01

By the surface response method, a regression equation is constructed, and the tensile elastic modulus of films made from polyvinyl alcohol/polyvinyl acetate (PVA/PVAc) blends filled with montmorillonite clay and microcrystalline cellulose nanoparticles is investigated. It is established that the introduction of the nanoparticles improves the mechanical properties of the blends in tension considerably: their strength and elastic modulus increase with content of the particles. Using the regression equation, the optimum composition of nanoparticlefilled PVA/PVAc blends with the highest value of elastic modulus is found.

Yeast Extract Promotes Cell Growth and Induces Production of Polyvinyl Alcohol-Degrading Enzymes

Directory of Open Access Journals (Sweden)

Min Li

2011-01-01

Full Text Available Polyvinyl alcohol-degrading enzymes (PVAases have a great potential in bio-desizing processes for its low environmental impact and low energy consumption. In this study, the effect of yeast extract on PVAases production was investigated. A strategy of four-point yeast extract addition was developed and applied to maximize cell growth and PVAases production. As a result, the maximum dry cell weight achieved was 1.48 g/L and the corresponding PVAases activity was 2.99 U/mL, which are 46.5% and 176.8% higher than the control, respectively. Applying this strategy in a 7 L fermentor increased PVAases activity to 3.41 U/mL. Three amino acids (glycine, serine, and tyrosine in yeast extract play a central role in the production of PVAases. These results suggest that the new strategy of four-point yeast extract addition could benefit PVAases production.

PIXE investigation of in-vitro release of chloramphenicol across polyvinyl alcohol/ acrylamide hydrogel

International Nuclear Information System (INIS)

Rihawi, M.; Al-Zeer, A.; Allaf, A.

2012-01-01

Hydrogels based on polyvinyl alcohol (PVA) and different amounts of acrylamide monomer (AAm) were prepared by thermal crosslinking process in solid state. The PVA/AAm hydrogels were investigated for drug delivery system applications. Chloramphenicol was adopted as a model drug to study its release behaviour across the prepared hydrogels. Particle induced X-ray emission (PIXE) analytical technique was utilized to study the drug release behaviour across the hydrogels. A comparison study between PIXE and UV measurements was performed. FTIR measurements were carried out to perform the molecular characterization. The releasing behaviour of the drug across the hydrogels demonstrates a decrease and a subsequent increase in the drug release rate, as the AAm amount increases. The FTIR characterization of the prepared hydrogels has shown a competitive behaviour between the crosslinking of PVA with AAm monomer or oligomerized AAm, depending on the amount of AAm added to prepare the PVA/AAm hydrogels. (author)

Tuning optical and three photon absorption properties in graphene oxide-polyvinyl alcohol free standing films

Energy Technology Data Exchange (ETDEWEB)

Karthikeyan, B., E-mail: bkarthik@nitt.edu; Hariharan, S. [Department of Physics, National Institute of Technology, Tiruchirappalli 620 015 (India); Udayabhaskar, R. [Department of Physics, National Institute of Technology, Tiruchirappalli 620 015 (India); Advanced Ceramics and Nanotechnology Laboratory, Department of Materials Engineering, University of Concepcion, Concepcion 4070386 (Chile)

2016-07-11

We report the optical and nonlinear optical properties of graphene oxide (GO)-polyvinyl alcohol (PVA) free standing films. The composite polymer films were prepared in ex-situ method. The variation in optical absorption spectra and optical constants with the amount of GO loading was noteworthy from the optical absorption spectroscopic studies. Nonlinear optical studies done at 532 nm using 5 ns laser pulses show three photon absorption like behaviour. Both steady state and time resolved fluorescence studies reveal that the GO was functioning as a pathway for the decay of fluorescence from PVA. This is attributed to the energy level modifications of GO through hydroxyl groups with PVA. Raman spectroscopy also supports the interaction between GO and PVA ions through OH radicals.

Tuning optical and three photon absorption properties in graphene oxide-polyvinyl alcohol free standing films

International Nuclear Information System (INIS)

Karthikeyan, B.; Hariharan, S.; Udayabhaskar, R.

2016-01-01

We report the optical and nonlinear optical properties of graphene oxide (GO)-polyvinyl alcohol (PVA) free standing films. The composite polymer films were prepared in ex-situ method. The variation in optical absorption spectra and optical constants with the amount of GO loading was noteworthy from the optical absorption spectroscopic studies. Nonlinear optical studies done at 532 nm using 5 ns laser pulses show three photon absorption like behaviour. Both steady state and time resolved fluorescence studies reveal that the GO was functioning as a pathway for the decay of fluorescence from PVA. This is attributed to the energy level modifications of GO through hydroxyl groups with PVA. Raman spectroscopy also supports the interaction between GO and PVA ions through OH radicals.

Photonic crystal fiber interferometric pH sensor based on polyvinyl alcohol/polyacrylic acid hydrogel coating.

Science.gov (United States)

Hu, Pengbing; Dong, Xinyong; Wong, Wei Chang; Chen, Li Han; Ni, Kai; Chan, Chi Chiu

2015-04-01

We present a simple photonic crystal fiber interferometer (PCFI) that operates in reflection mode for pH measurement. The sensor is made by coating polyvinyl alcohol/polyacrylic acid (PVA/PAA) hydrogel onto the surface of the PCFI, constructed by splicing a stub of PCF at the distal end of a single-mode fiber with its free end airhole collapsed. The experimental results demonstrate a high average sensitivity of 0.9 nm/pH unit for the 11 wt.% PVA/PAA coated sensor in the pH range from 2.5 to 6.5. The sensor also displays high repeatability and stability and low cross-sensitivity to temperature. Fast, reversible rise and fall times of 12 s and 18 s, respectively, are achieved for the sensor time response.

Development and blood compatibility assessment of electrospun polyvinyl alcohol blended with metallocene polyethylene and plectranthus amboinicus (PVA/mPE/PA for bone tissue engineering

Directory of Open Access Journals (Sweden)

Qi J

2018-05-01

Full Text Available Jie Qi,1,* Huang Zhang,2,* Yingzhou Wang,3 Mohan Prasath Mani,4 Saravana Kumar Jaganathan5–7 1Department of Orthopedics, Shaanxi Provincial People’s Hospital, 2Department of Orthopedics, Han Zhong People’s Hospital, Han Zhong, Shaanxi Province, 3Beijing Meinuoyikang Health Food Co., Ltd, Beijing, People’s Republic of China; 4Faculty of Biosciences and Medical Engineering, Universiti Teknologi Malaysia, Skudai, Johor, Malaysia; 5Department for Management of Science and Technology Development, 6Faculty of Applied Sciences, Ton Duc Thang University, Ho Chi Minh City, Vietnam; 7IJN-UTM Cardiovascular Engineering Centre, Department of Clinical Sciences, Faculty of Biosciences and Medical Engineering, Universiti Teknologi Malaysia, Skudai, Johor, Malaysia *These authors contributed equally to this work Introduction: Currently, the design of extracellular matrix (ECM with nanoscale properties in bone tissue engineering is challenging. For bone tissue engineering, the ECM must have certain properties such as being nontoxic, highly porous, and should not cause foreign body reactions. Materials and methods: In this study, the hybrid scaffold based on polyvinyl alcohol (PVA blended with metallocene polyethylene (mPE and plectranthus amboinicus (PA was fabricated for bone tissue engineering via electrospinning. The fabricated hybrid nanocomposites were characterized by scanning electron microscopy (SEM, Fourier transform and infrared spectroscopy (FTIR, thermogravimetric analysis (TGA, contact angle measurement, and atomic force microscopy (AFM. Furthermore, activated partial thromboplastin time (APTT, prothrombin time (PT, and hemolytic assays were used to investigate the blood compatibility of the prepared hybrid nanocomposites. Results: The prepared hybrid nanocomposites showed reduced fiber diameter (238±45 nm and also increased porosity (87% with decreased pore diameter (340±86 nm compared with pure PVA. The interactions between PVA, m

Fabrication and application of coaxial polyvinyl alcohol/chitosan nanofiber membranes

Directory of Open Access Journals (Sweden)

Kuo Ting-Yun

2017-12-01

Full Text Available It is difficult to fabricate chitosan-wrapped coaxial nanofibers, because highly viscous chitosan solutions might hinder the manufacturing process. To overcome this difficulty, our newly developed method, which included the addition of a small amount of gum arabic, was utilized to prepare much less viscous chitosan solutions. In this way, coaxial polyvinyl alcohol (PVA/chitosan (as core/shell nanofiber membranes were fabricated successfully by coaxial electrospinning. The core/shell structures were confirmed by TEM, and the existence of PVA and chitosan was also verified using FT-IR and TGA. The tensile strength of the nanofiber membranes was increased from 0.6-0.7 MPa to 0.8-0.9 MPa after being crosslinked with glutaraldehyde. The application potential of the PVA/chitosan nanofiber membranes was tested in drug release experiments by loading the core (PVA with theophylline as a model drug. The use of the coaxial PVA/chitosan nanofiber membranes in drug release extended the release time of theophylline from 5 minutes to 24 hours. Further, the release mechanisms could be described by the Korsmeyer-Peppas model. In summary, by combining the advantages of PVA and chitosan (good mechanical strength and good biocompatibility respectively, the coaxial PVA/chitosan nanofiber membranes are potential biomaterials for various biomedical applications.

Quantitative comparison between the gel-film and polyvinyl alcohol methods for dehydrogenase histochemistry reveals different intercellular distribution patterns of glucose-6-phosphate and lactate dehydrogenases in mouse liver

NARCIS (Netherlands)

Griffini, P.; Vigorelli, E.; Bertone, V.; Freitas, I.; van Noorden, C. J.

1994-01-01

The precise histochemical localization and quantification of the activity of soluble dehydrogenases in unfixed cryostat sections requires the use of tissue protectants. In this study, two protectants, polyvinyl alcohol (PVA) and agarose gel, were compared for assaying the activity of lactate

Fabrication of Antibacterial Poly(Vinyl Alcohol Nanocomposite Films Containing Dendritic Polymer Functionalized Multi-Walled Carbon Nanotubes

Directory of Open Access Journals (Sweden)

Andreas Sapalidis

2018-03-01

Full Text Available A series of poly(vinyl alcohol (PVA nanocomposite films containing quaternized hyperbranched polyethyleneimine (PEI functionalized multi-walled carbon nanotubes (ox-CNTs@QPEI are prepared by solvent casting technique. The modified carbon-based material exhibits high aqueous solubility, due to the hydrophilic character of the functionalized hyperbranched dendritic polymer. The quaternized PEI successfully wraps around nanotube walls as polycations provide electrostatic repulsion. Various contents of ox-CNTs@QPEI ranging from 0.05 to 1.0% w/w were employed to prepare functionalized PVA nanocomposites. The developed films exhibit adequate optical transparency, improved mechanical properties and extremely high antibacterial behavior due to the excellent dispersion of the functionalized CNTs into the PVA matrix.

Chitosan/(polyvinyl alcohol)/zeolite electrospun composite nanofibrous membrane for adsorption of Cr{sup 6+}, Fe{sup 3+} and Ni{sup 2+}

Energy Technology Data Exchange (ETDEWEB)

Habiba, Umma; Afifi, Amalina M.; Salleh, Areisman; Ang, Bee Chin, E-mail: amelynang@um.edu.my

2017-01-15

Highlights: • Chitosan/PVA/zeolite nanofibrous composite membrane was prepared by electrospinning method as a new chitosan based composite membrane. • The notable property of the resulting nanofibrous composite membrane is the rigidity and no weight loss in distilled water, basic and acidic medium. • Heavy metal removal effectiveness reaches to almost 100%, as the initial concentration of heavy metal is 10–20 mg/L. • The kinetic rate of adsorption is very high. • The reusability of the chitosan/PVA/zeolite nanofibrous membrane is an important finding of the current study. - Abstract: In this study, chitosan/polyvinyl alcohol (PVA)/zeolite nanofibrous composite membrane was fabricated via electrospinning. First, crude chitosan was hydrolyzed with NaOH for 24 h. Afterward, hydrolyzed chitosan solution was blended with aqueous PVA solution in different weight ratios. Morphological analysis of chitosan/PVA electrospun nanofiber showed a defect-free nanofiber material with 50:50 weight ratio of chitosan/PVA. Subsequently, 1 wt.% of zeolite was added to this blended solution of 50:50 chitosan/PVA. The resulting nanofiber was characterized with field emission scanning electron microscopy, X-Ray diffraction, Fourier transform infrared spectroscopy, swelling test, and adsorption test. Fine, bead-free nanofiber with homogeneous nanofiber was electrospun. The resulting membrane was stable in distilled water, acidic, and basic media in 20 days. Moreover, the adsorption ability of nanofibrous membrane was studied over Cr (VI), Fe (III), and Ni (II) ions using Langmuir isotherm. Kinetic parameters were estimated using the Lagergren first-order, pseudo-second-order, and intraparticle diffusion kinetic models. Kinetic study showed that adsorption rate was high. However, the resulting nanofiber membrane showed less adsorption capacity at high concentration. The adsorption capacity of nanofiber was unaltered after five recycling runs, which indicated the reusability of

Construction Materials for Coastal Structures.

Science.gov (United States)

1983-02-01

formaldehyde derivatives. Thermoplastic materials include polyvinyl alcohol and polyacrylamides. PPCC process technology is based upon overcoming the...entrained air from a concrete mixture. Compounds such as tributyl phosphate, diburyl phthalate, water-insoluble alcohols , and water-insoluble esters of...of hydrolysis of wood is small and is dependent on the temperature. 0 (3) Wood Oxidation. Wood oxydation by air in dry locations is slow and attacks

Blends of caprolactam/caprolactone copolymers and chlorinated polymers

NARCIS (Netherlands)

Alberda van Ekenstein, G.O.R.; Deuring, H.; ten Brinke, G.; Ellis, T.S.

The phase behaviour of blends of chlorinated polyethylene, polyvinyl chloride (PVC) and chlorinated PVC with random copolymers of caprolactone and caprolactam has been investigated and the results correlated with a binary interaction model. The known miscibility of polycaprolactone in the

Influence of Polyvinyl Alcohol (PVA) Addition on Silica Membrane Performance Prepared from Rice Straw

Science.gov (United States)

Wahyuningsih, S.; Ramelan, A. H.; Wardoyo, D. T.; Ichsan, S.; Kristiawan, Y. R.

2018-03-01

The utilization and modification of silica from rice straw as the main ingredient of adsorbent has been studied. The aim of this study was to determine the optimum composition of PVA (polyvinyl alcohol): silica to produce adsorbents with excellent pore characteristics, optimum adsorption efficiency and optimum pH for methyl yellow adsorptions. X-Ray Fluorescence (XRF) analysis results showed that straw ash contains 82.12 % of silica (SiO2). SAA (Surface Area Analyzer) analysis showed optimum composition ratio 5:5 of PVA: silica with surface area of 1.503 m2/g. Besides, based on the pore size distribution of PVA: silica (5:5) showed the narrow pore size distribution with the largest pore cumulative volume of 2.8 x 10-3 cc/g. The optimum pH for Methanyl Yellow adsorption is pH 2 with adsorption capacity = 72.1346%.

Biodegradable Mulches Based on Poly(vinyl Alcohol, Kenaf Fiber, and Urea

Directory of Open Access Journals (Sweden)

Boon Khoon Tan

2015-07-01

Full Text Available This paper describes the preparation of poly(vinyl alcohol/kenaf fiber (PVOH/KF composites with entrapped urea. The major FTIR peaks of these composites could be identified. These composites are intended for agricultural applications as biodegradable mulches and could be potential carrier materials for fertilizer. The water solubility, release behavior, chemical properties, and thermal stability of the composites were evaluated. The composites lost 25% of their weight after 7 days in water. In a wet environment, urea was released from the composites through its dissolution in water, and around 57% of the urea was released from the composites in 24 h; Thermagravimetric analysis showed that these composites were stable up 150 C. These composites would be able to withstand rain and protect seedlings from the sun when applied in the field as mulches. For around three to four weeks, these biobased mulches could slowly disintegrate as the PVOH binder was gradually dissolved by moisture, releasing the kenaf fibers to serve as soil fertilizer without leaving any undegradable waste for disposal. Hence, they would not pose any risks to the land or biological systems.

ESR Study of the polyvinyl alcohol gamma-ray induced free-radicals

International Nuclear Information System (INIS)

Rosas S, E.

1994-01-01

This work reports the findings of the molecular weight effect on the electron spin resonance saturation curve of the gamma-ray irradiated polyvinyl alcohol, G-RIPVA. It has been noted that Pva of a lower molecular weight, between 13,000-23,000, show some noticeable differences in the electron spin resonance, ESR, response as a function of the gamma-ray dose in the 1-100 k Gy range than the one reported in the literature with molecular weight of 108,000. Results show a linear response in the log-log plot of the dose vs ESR signal intensity for samples based on G-RIPVA of the lower molecular weight as contrasted with the non-linear ESR response of G-RIPVA of higher molecular weight in the above named dose range. Such a result has been assumed to arise from the shorter molecular chains for the case of the lower molecular weight samples making this to increase the production of Pva free radicals with respect to the absorbed studied doses. Also, a discussion on the nature and stability of the Pva free radicals will be given. (Author)

Physical changes on the radiation and heat induced poly(Vinyl alcohol) fibers

Energy Technology Data Exchange (ETDEWEB)

Nho, Young Chang; Park, Kyung Ran; Park, Jong Seok; Lim, Youn Mook; Kang, Phil Hyun [Research Division for Industry and Environment, Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-11-15

Poly(vinyl alcohol) (PVA) has high tensile strength and flexibility as well as oxygen barrier properties. The water, which acts as a plasticizer, reduces the tensile strength of PVA and swells PVA as well. It needs to have high water-resistant depending on its applications, especially for the use as tire cords. The aim of this work was to investigate the effect of the annealing temperature and radiation on the Gel content and tensile strength of PVA fbers. For this purpose, gel fraction and tensile strength were determined and analyzed. Annealing was performed in the temperature range of 120-180℃ for 10 min. PVA fbers were irradiated by using a conventional electron beam irradiation at a radiation dose of 50⁓200 kGy, at a dose of 10 kGy/pass at room temperature (acceleration voltage of 1 MeV). Annealing markedly increased the Gel content and the tensile strength of PVA fbers. However irradiation lowered the Gel content and the tensile strength of PVA fbers because they were degraded easily by radiation.

In vitro release of metformin hydrochloride from sodium alginate/polyvinyl alcohol hydrogels.

Science.gov (United States)

Martínez-Gómez, Fabián; Guerrero, Juan; Matsuhiro, Betty; Pavez, Jorge

2017-01-02

Hydrogels, based on polysaccharides have found a number of applications as drug delivery carriers. In this work, hydrogels of full characterized sodium alginate (Mn 87,400g/mol) and commercial poly(vinyl alcohol) (PVA) sensitive to pH and temperature stimuli were obtained using a simple, controlled, green, low cost method based on freeze-thaw cycles. Stable hydrogels of sodium alginate/PVA with 0.5:1.5 and 1.0:1.0w/v concentrations showed very good swelling ratio values in distilled water (14 and 20g/g, respectively). Encapsulation and release of metformin hydrochloride in hydrogels of 1.0:1.0w/v sodium alginate/PVA was followed by UV spectroscopy. The hydrogel released a very low amount of metformin hydrochloride at pH 1.2; the highest release value (55%) was obtained after 6h at pH 8.0. Also, the release of metformin hydrochloride was studied by 1 H NMR spectroscopy, the temporal evolution of methyl group signals of metformin showed 30% of drug release after 3h. Copyright © 2016 Elsevier Ltd. All rights reserved.

Preparation and characterization of silk sericin/PVA blend film with silver nanoparticles for potential antimicrobial application.

Science.gov (United States)

He, Huawei; Cai, Rui; Wang, Yejing; Tao, Gang; Guo, Pengchao; Zuo, Hua; Chen, Liqun; Liu, Xinyu; Zhao, Ping; Xia, Qingyou

2017-11-01

Sericin has great potentials in biomedical applications for its good reactive activity, biocompatibility and biodegradability. However, the undesirable mechanical performance limits its application. Here, we developed a green, facile and economic approach to prepare sericin/polyvinyl alcohol (PVA) blend film. Further, silver nanoparticles (AgNPs) were synthesized in situ on the surface of sericin/PVA film via UV-assisted green synthesis method. Mechanical performance, swelling, mass losing and water retention tests showed the blend film had good mechanical performance, hygroscopicity, water retention capacity and low mass losing ratio. Scanning electron microscopy, fourier transfer infrared spectroscopy, X-ray diffractometry diffraction and X-ray photoelectron spectroscopy indicated the blending of PVA and sericin promoted the formation of hydrogen bond network between sericin and PVA, thus enhanced the mechanical performance and the stability of sericin, as well as the hygroscopicity and water retention capacity. UV irradiation and AgNPs modification did not affect the inner crystalline structure of sericin/PVA blend film. The inhibition zone and bacteria growth curve assay suggested AgNPs-sericin/PVA film had good antibacterial activities against E. coli and S. aureus. This novel AgNPs-sericin/PVA film shows great potentials in biomedical materials such as wound dressing and skin tissue engineering. Copyright © 2017 Elsevier B.V. All rights reserved.

PPY-PVA Blend Thin Films as a Ammines Gas Sensor

Directory of Open Access Journals (Sweden)

D. B. DUPARE

2009-06-01

Full Text Available Synthesis of polypyrrole–polyvinyl alcohol blend thin by in situ chemical oxidative polymerization, on glass substrate for development of Ammonia and Trimethyl ammine hazardous gas sensor. The all experimental process carried out at room temperature (304 k. These polymer materials were characterized by Chemical analyses, spectral studies (UV-visible and IR and conductivity measurement by four –probe technique. The surface morphology as seen in the SEM image was observed to be granular, tubular, uniformly covering the entire substrate surface having porous in nature. The current–voltage characterization show that these thin films have conducting in nature having ohmic behaviors. The sensor was used for different concentration (ppm of TMA and Ammonia gas investigation at room temperature (304 k. This study found to possess improved electrical, mechanical and environmental stability PPY-PVA films.

Synthesis and Characterization of Fe3O4 Nanoparticles using Polyvinyl Alcohol (PVA) as Capping Agent and Glutaraldehyde (GA) as Crosslinker

Science.gov (United States)

Budi Hutami Rahayu, Lale; Oktavia Wulandari, Ika; Herry Santjojo, Djoko; Sabarudin, Akhmad

2018-01-01

The use of polyvinyl alcohol (PVA) as a capping agent and glutaraldehyde (GA) as a crosslinker for a synthesis of magnetite (Fe3O4) nanoparticles is able to reduce agglomeration of produced Fe3O4. Additionally, oxidation of Fe3O4 by air could be avoided. The synthesis is carried out in two steps: first step, magnetite (Fe3O4) nanoparticles were prepared by dissolving the FeCl3.6H2O and FeCl2.4H2O in alkaline media (NH3.H2O). The second step, magnetite nanoparticles were coated with polyvinyl alcohol (PVA) and glutaraldehyde (GA) to obtain Fe3O4-PVA-GA. The latter material was then characterized by FTIR to determine the typical functional groups of magnetite coated with PVA-GA. X-ray Diffraction analysis was used to determine structure and size of crystal as well as the percentage of magnetite produced. It was found that the produced nanoparticles have crystal sizes around 4-9 nm with the cubic crystal structure. The percentage of magnetite phase increases when the amount of glutaraldehyde increased. SEM-EDX was employed to assess the surface morphology and elemental composition of the resulted nanoparticles. The magnetic character of the magnetite and Fe3O4- PVA-GA were studied using Electron Spin Resonance.

Structural, mechanical and electrical properties biopolymer blend nanocomposites derived from poly (vinyl alcohol)/cashew gum/magnetite

Science.gov (United States)

Ramesan, M. T.; Jayakrishnan, P.; Manojkumar, T. K.; Mathew, G.

2018-01-01

Blending of poly vinyl alcohol (PVA) and natural biopolymers such as cashew gum (CG) with magnetite (Fe3O4) nanoparticles has been a promising way for preparing bio-degradable polymeric blend nanocomposites. PVA/CG/Fe3O4 blend nanocomposites have been prepared by a simple solution casting technique using water as the green solvent. The characterization of blend nanocomposites has been carried out by using Fourier transform infrared, UV, x-ray diffraction (XRD), high resolution transmission electron microscopy, scanning electron microscopy (SEM), differential scanning calorimetry, thermogravimetric analysis, mechanical properties and electrical conductivity. The interaction between nanoparticles and the blend segments was confirmed from the shift in characteristic absorption peaks of nanocomposites compared to PVA/CG blend. XRD analysis has shown the presence of crystalline peaks of nanoparticles in the blend matrix. The uniform distribution of Fe3O4 nanoparticles in the blend was revealed by TEM and SEM. The strong interaction of nanoparticles with the blend has been confirmed by the increase in glass transition temperature resulting from the reduced flexibility of the blend nanocomposite compared to that of the blend system. An increase in thermal stability and tensile strength and reduction in elongation at break of nanocomposites have been noticed with the increasing loading of nanoparticles. The AC electrical conductivity, dielectric constant and dielectric loss of the nanocomposites have been found to be higher than that of the blend. Generally, it can be stated that the magnetite nanoparticles acts as a potential filler in the PVA/CG blend at 7 wt% loading, giving the best balance of properties.

Studies on the thermal and electrical properties of polyethylene oxide/polyvinyl alcohol blend by incorporating of Cesium Chloride

Science.gov (United States)

Ragab, H. M.

The composites PVA/PEO filled with various concentrations of CsCl samples, which were prepared for using a solvent casting technique and studied via Fourier transform infrared spectroscopy (FTIR), ultraviolet - visible (UV-Vis), X-ray spectroscopy, Scanning electron microscopy (SEM), AC conductivity and dielectric properties to use as sensor in electronic devices. The FTIR indicated the interaction between PVA/PEO and CsCl. From data of UV. Vis. was observed band gap (Eg) reduces with addition CsCl to polymer blend. The XRD shows the degree of crystallinity (χ%) decreasing with increasing concentration of CsCl from 2.93 to 2.45. The SEM of the surface of composite PVA/PEO filled with various concentrations of CsCl in magnification 1500 times its change with compare of pure blend. From TGA was observed improvement in the thermal stability of the samples after addition of CsCl. The AC conductivity rise more rapidly with temperature and associated with activation energy Ea, for conduction and enhanced with increasing both temperature and frequency.

Biodegradable foams based on starch, polyvinyl alcohol, chitosan and sugarcane fibers obtained by extrusion

Directory of Open Access Journals (Sweden)

Flávia Debiagi

2011-10-01

Full Text Available Biodegradable foams made from cassava starch, polyvinyl alcohol (PVA, sugarcane bagasse fibers and chitosan were obtained by extrusion. The composites were prepared with formulations determined by a constrained ternary mixtures experimental design, using as variables: (X1 starch / PVA (100 - 70%, (X2 chitosan (0 - 2% and (X3 fibers from sugar cane (0 - 28%. The effects of varying proportions of these three components on foam properties were studied, as well the relationship between their properties and foam microstructure. The addition of starch/PVA in high proportions increased the expansion index and mechanical resistance of studied foams. Fibers addition improved the expansion and mechanical properties of the foams. There was a trend of red and yellow colors when the composites were produced with the highest proportions of fibers and chitosan, respectively. All the formulations were resistant to moisture content increase until 75% relative humidity of storage.

Growth and characteristics of PbS/polyvinyl alcohol nanocomposites for flexible high dielectric thin film applications

International Nuclear Information System (INIS)

Hmar, J.J.L.; Majumder, T.; Mondal, S.P.

2016-01-01

PbS/polyvinyl alcohol (PbS/PVA) nanocomposites have been grown by a chemical bath deposition process at various growth temperatures (60–100 °C). Transmission electron microscopy (TEM) study revealed the formation of PbS nanoparticles of diameter 6–20 nm encapsulated in PVA matrix. Optical band gap of the nanocomposite films have been found to decrease (1.45 eV–0.67 eV) with increase in growth temperature from 60 °C to 100 °C. The impedance measurements have been carried out by depositing the PbS/PVA films on indium tin oxide (ITO) coated flexible polyethylene terephthalate (PET) substrates. The room temperature dielectric permittivity and ac conductivity measurements have been carried out for ITO/PbS/PVA/Al devices deposited at various growth temperatures. The nanocomposite films demonstrate superior dielectric permittivity compare to pure PVA polymer. The flexibility studies of ITO/PbS/PVA/Al devices have been performed at different bending angles. - Highlights: • PbS nanoparticles of diameter 6–20 nm were grown in polyvinyl (PVA) matrix. • Optical band gap of nanocomposite films was varied from 1.45–0.67 eV. • The nanocomposite thin films demonstrated superior dielectric permittivity. • Flexibility study of thin film devices was performed at various bending angles.

Electromechanical behavior of polyaniline/poly (vinyl alcohol) blend films under static, dynamic and time-dependent strains

International Nuclear Information System (INIS)

Akhilesan, S; Lakshmana Rao, C; Varughese, S

2014-01-01

We report on the experimentally observed electrical conductivity enhancement in polyaniline/poly (vinyl alcohol) blend films under uniaxial tensile loading. Polyaniline (PANI) is an intrinsically conducting polymer, which does not form stretchable free-standing films easily and hence its electromechanical characterization is a challenge. Blending of PANI with other insulating polymers is a good choice to overcome the processability problem. We report the electromechanical response of solution blended and HCl doped PANI/PVA blends subjected to uniaxial, static, dynamic and time-dependent tensile loading. The demonstrated viscoelastic and morphological contributions of the component polymers to the electrical conductivity behavior in these blends could lead to interesting applications in strain sensors and flexible electronics. The reversibility of the electromechanical response under dynamic strain is found to increase in blends with higher PANI content. Time-dependent conductivity studies during mechanical stress relaxation reveal that variations in the micro-domain ordering and the relative relaxation rate of the individual polymer phases can give rise to interesting electrical conductivity changes in PANI blends. From morphological and electrical conductivity studies, we show that PANI undergoes primary and secondary agglomeration behavior in these blends that contributes to the changes in conductivity behavior during the deformation. A 3D variable range hopping (VRH) process, which uses a deformable core and shell concept based on blend morphology analysis, is used to explain the experimentally observed electromechanical behavior. (papers)

Blend membrane of succinic acid-crosslinked chitosan grafted with heparin/PVA-PEG (polyvinyl alcohol-polyethylene glycol) and its characterization

Science.gov (United States)

Sangkota, V. D. A.; Lusiana, R. A.; Astuti, Y.

2018-04-01

Crosslinking and grafting reactions are required to modify the functional groups on chitosan to increase the number of its active groups. In this study, crosslinking reaction of succinic acid and grafting reaction of heparin on chitosan were conducted to produce a membrane as a candidate of a hemodialysis membrane. The mole ratio between chitosan and succinate acids was varied to obtain the best composition of modified materials. By blending all the material composition with PVA-PEG, the blend was transformed into a membrane. The resulted membrane was then characterized by various test methods such as tests of thickness, weight, water uptake, pH resistance, tensile strength and membrane hydrophilicity. The results showed that the best composition of the membrane reached in the addition of 0.011 gram of succinic acid proved by its highest mechanical strength compared to the other membranes.

Preparation and characterization of jackfruit seed starch/poly (vinyl alcohol) (PVA) blend film

Science.gov (United States)

Sarifuddin, N.; Shahrim, N. A.; Rani, N. N. S. A.; Zaki, H. H. M.; Azhar, A. Z. A.

2018-01-01

From the environmental point of view, biodegradable materials have been rapidly developed in the past years. PVA is one of the biodegradable synthetic polymers commonly used, but its degradation rate is slow. As an alternative to reduce plastic waste and accelerate the degradation process, PVA frequently blended with other natural polymers to improve its biodegradability. The natural polymer such as starch has high potential in enhancing PVA biodegradability by blending both components. The usage of starch extracted from agriculture wastes such as jackfruit seed is quite promising. In this study, jackfruit seed starch (JFSS)/poly (vinyl alcohol) (PVA) blend films were prepared using the solution casting method. The effect of starch content on the mechanical (tensile strength and elongation to break %) and physical properties of the tested films were investigated. The optimum tensile strength was obtained at 10.45 MPa when 4 wt. % of starch added to the blend. But, decreasing trend of tensile strength was found upon increasing the amount of starch beyond 4 wt. % in starch/PVA blend films. Nevertheless, elongation at break decreases with the increase in starch content. The mechanical properties of the blend films are supported by the Field Emission Scanning Electron Microscopy (FESEM), in which the native JFSS granules are wetted by PVA continuous phase with good dispersion and less agglomeration. The incorporation of JFSS in PVA has also resulted in the appearance of hydrogen bond peak, which evidenced by Fourier Transform Infrared (FTIR). Additionally, the biodegradation rate of JFSS/PVA was evaluated through soil burial test.

Mechanical and electromagnetic interference shielding Properties of poly(vinyl alcohol)/graphene and poly(vinyl alcohol)/multi-walled carbon nanotube composite nanofiber mats and the effect of Cu top-layer coating.

Science.gov (United States)

Fujimori, Kazushige; Gopiraman, Mayakrishnan; Kim, Han-Ki; Kim, Byoung-Suhk; Kim, Ick-Soo

2013-03-01

We report the mechanical property and electromagnetic interference shielding effectiveness (EMI SE) of poly(vinyl alcohol) (PVA)/graphene and PVA/multi-walled carbon nanotube (MWCNT) composite nanofibers prepared by electrospinning. The metal (Cu) was deposited on the resultant PVA composite nanofibers using metal deposition technique in order to improve the mechanical properties and EMI shielding properties. The resulting PVA composite nanofibers and Cu-deposited corresponding nanofibers were characterized by field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and wide angle X-ray diffraction (WAXD). Tensile tests were performed on the PVA/graphene and PVA/MWCNT composite nanofibers. The tensile strength of the PVA/graphene and PVA/MWCNT composite nanofibers was found to be 19.2 +/- 0.3 MPa at graphene content - 6.0 wt% and 12.2 +/- 0.2 MPa at MWCNT content - 3.0 wt%, respectively. The EMI SE of the Cu-deposited PVA/graphene composite nanofibers was significantly improved compared to pure PVA/graphene composite nanofibers, and also depended on the thickness of Cu metal layer deposited on the PVA composite nanofibers.

Fumed Silica Nanoparticles Incorporated in Quaternized Poly(Vinyl Alcohol Nanocomposite Membrane for Enhanced Power Densities in Direct Alcohol Alkaline Fuel Cells

Directory of Open Access Journals (Sweden)

Selvaraj Rajesh Kumar

2015-12-01

Full Text Available A nanocomposite polymer membrane based on quaternized poly(vinyl alcohol/fumed silica (QPVA/FS was prepared via a quaternization process and solution casting method. The physico-chemical properties of the QPVA/FS membrane were investigated. Its high ionic conductivity was found to depend greatly on the concentration of fumed silica in the QPVA matrix. A maximum conductivity of 3.50 × 10−2 S/cm was obtained for QPVA/5%FS at 60 °C when it was doped with 6 M KOH. The permeabilities of methanol and ethanol were reduced with increasing fumed silica content. Cell voltage and peak power density were analyzed as functions of fumed silica concentration, temperature, methanol and ethanol concentrations. A maximum power density of 96.8 mW/cm2 was achieved with QPVA/5%FS electrolyte using 2 M methanol + 6 M KOH as fuel at 80 °C. A peak power density of 79 mW/cm2 was obtained using the QPVA/5%FS electrolyte with 3 M ethanol + 5 M KOH as fuel. The resulting peak power densities are higher than the majority of published reports. The results confirm that QPVA/FS exhibits promise as a future polymeric electrolyte for use in direct alkaline alcoholic fuel cells.

Nanofibrous nonmulberry silk/PVA scaffold for osteoinduction and osseointegration.

Science.gov (United States)

Bhattacharjee, Promita; Kundu, Banani; Naskar, Deboki; Maiti, Tapas K; Bhattacharya, Debasis; Kundu, Subhas C

2015-05-01

Poly-vinyl alcohol and nonmulberry tasar silk fibroin of Antheraea mylitta are blended to fabricate nanofibrous scaffolds for bone regeneration. Nanofibrous matrices are prepared by electrospinning the equal volume ratio blends of silk fibroin (2 and 4 wt%) with poly-vinyl alcohol solution (10 wt%) and designated as 2SF/PVA and 4SF/PVA, respectively with average nanofiber diameters of 177 ± 13 nm (2SF/PVA) and 193 ± 17 nm (4SF/PVA). Fourier transform infrared spectroscopy confirms retention of the secondary structure of fibroin in blends indicating the structural stability of neo-matrix. Both thermal stability and contact angle of the blends decrease with increasing fibroin percentage. Conversely, fibroin imparts mechanical stability to the blends; greater tensile strength is observed with increasing fibroin concentration. Blended scaffolds are biodegradable and support well the neo-bone matrix synthesis by human osteoblast like cells. The findings indicate the potentiality of nanofibrous scaffolds of nonmulberry fibroin as bone scaffolding material. © 2014 Wiley Periodicals, Inc.

Characterization and application of zeolitic imidazolate framework-8@polyvinyl alcohol nanofibers mats prepared by electrospinning

Science.gov (United States)

Fan, Xiaoxiao; Yu, Linling; Li, Lianghao; Yang, Cao; Wen, Junjie; Ye, Xiaokun; Cheng, Jianhua; Hu, Yongyou

2017-02-01

In this study, Zeolitic imidazolate framework-8@polyvinyl alcohol (ZIF-8@PVA) nanofibers were creatively fabricated by electrospinning technique, and the nanofibers membranes were characterized by SEM, TEM, XRD, FTIR, TG, DSC, DTA, BET. Its thermal stability, mechanical property, water stability and adsorption nature were also performed. The optimized fabrication parameter of the ZIF-8@PVA was 10 wt% and the uniform diameters of the nanofibers has been obtained. In addition, the ZIF-8@PVA nanofibers displayed unique properties such as a water stable and flexible structure. The adsorption test for Congo red treatment revealed that the nanofibers had a great adsorption performance. The results indicated that the nonwoven fiber mats had a great potential as a new type of membrane adsorbents in wastewater purification. The possible mechanism of CR adsorption onto ZIF-8@PVA was researched.

Studies on the thermal and electrical properties of polyethylene oxide/polyvinyl alcohol blend by incorporating of Cesium Chloride

Directory of Open Access Journals (Sweden)

H.M. Ragab

Full Text Available The composites PVA/PEO filled with various concentrations of CsCl samples, which were prepared for using a solvent casting technique and studied via Fourier transform infrared spectroscopy (FTIR, ultraviolet – visible (UV–Vis, X-ray spectroscopy, Scanning electron microscopy (SEM, AC conductivity and dielectric properties to use as sensor in electronic devices. The FTIR indicated the interaction between PVA/PEO and CsCl. From data of UV. Vis. was observed band gap (Eg reduces with addition CsCl to polymer blend. The XRD shows the degree of crystallinity (χ% decreasing with increasing concentration of CsCl from 2.93 to 2.45. The SEM of the surface of composite PVA/PEO filled with various concentrations of CsCl in magnification 1500 times its change with compare of pure blend. From TGA was observed improvement in the thermal stability of the samples after addition of CsCl. The AC conductivity rise more rapidly with temperature and associated with activation energy Ea, for conduction and enhanced with increasing both temperature and frequency. Keywords: PVA/PEO composite, X-ray, TGA, AC conductivity, Dielectric loss

Structure-sensitive film materials based on polyvinyl alcohol compositions with polyacids

Science.gov (United States)

Lazareva, Tatjana G.; Iljushenko, Irina A.

1995-05-01

The influence of polyacidic additives (silicotungstic acid -- STA, carboxymethylcellulose -- Na-CMC, polymethacrylic acid -- PMA, polyacrylic acid -- PAA) on the molecular mobility of film composition based on polyvinyl alcohol (PVA) in the temperature range 20 - 200 degree(s)C has been evaluated. It has been concluded that interpolymer complexes are formed due to hydrogen bonding of the PVA and polyacidic additive molecules, which results in the change of the PVA stereoregularity. The formation of the complexes depends on the type and concentration of the polyacidic additive, the process of (alpha) -relaxation and, in a certain concentration range of the additive, increases the molecular mobility of the kinetic segments surrounding the complex. The influence of short-term UV-irradiation on the structure and properties of such materials has been investigated. A possibility of the reversible change of molecular mobility and stereoregularity of the examined compositions as a result of short-term UV-irradiation has been established. Introduction of polyacids into the PVA structure gives rise to the electrosensitivity, i.e., the ability to change structure under the action of an electric field. In this case the distinguishing feature is the relation between the molecular mobility and electrosensitivity in the range of parameters where the (alpha) - relaxation occurs.

Electrical conductivity studies on Ammonium bromide incorporated with Zwitterionic polymer blend electrolyte for battery application

Science.gov (United States)

Parameswaran, V.; Nallamuthu, N.; Devendran, P.; Nagarajan, E. R.; Manikandan, A.

2017-06-01

Solid polymer blend electrolytes are widely studied due to their extensive applications particularly in electrochemical devices. Blending polymer makes the thermal stability, higher mechanical strength and inorganic salt provide ionic charge carrier to enhance the conductivity. In these studies, 50% polyvinyl alcohol (PVA), 50% poly (N-vinyl pyrrolidone) (PVP) and 2.5% L-Asparagine mixed with different ratio of the Ammonium bromide (NH4Br), have been synthesized using solution casting technique. The prepared PVA/PVP/L-Asparagine/doped-NH4Br polymer blend electrolyte films have been characterized by various analytical methods such as FT-IR, XRD, impedance spectroscopy, TG-DSC and scanning electron microscopy. FT-IR, XRD and TG/DSC analysis revealed the structural and thermal behavior of the complex formation between PVA/PVP/L-Asparagine/doped-NH4Br. The ionic conductivity and the dielectric properties of PVA/PVP/L-Asparagine/doped-NH4Br polymer blend electrolyte films were examined using impedance analysis. The highest ionic conductivity was found to be 2.34×10-4 S cm-1 for the m.wt. composition of 50%PVA:50%PVP:2.5%L-Asparagine:doped 0.15 g NH4Br at ambient temperature. Solid state proton battery is fabricated and the observed open circuit voltage is 1.1 V and its performance has been studied.

Preparation and properties of poly(vinyl alcohol)-g-octadecanol copolymers based solid–solid phase change materials

International Nuclear Information System (INIS)

Shi Haifeng; Li Jianhua; Jin Yanmei; Yin Yiping; Zhang Xingxiang

2011-01-01

Highlights: ► In this paper, our objective is just focused on the preparation and characterization of such SSPCMs aiming at providing one suitable material for improving the thermal stability and preventing the liquid leakage from the matrix. Here, the SSPCMs can be fabricated by grafting to method between poly(vinyl alcohol) and octadecanol, which the grafting ratio can be controlled by adjusting the feeding components. ► The thermal properties, crystalline structure and morphology were detailed studies by WAXD, FT-IR, TGA and DSC, proving that the PVA-g-octadecanol process the better thermal storage ability and thermal stability. Compared with pure octadecanol, the heat fusion of PVA-g-octadecanol decreased due to the mobility confinement and the lower rearrangements of C18 alkyl side chains. ► This result is for the first time reported, and is a meaningful result for the investigation of the solid–solid phase change materials, and the preparation process provides one template-directed approach to obtain the high-performance materials with the better heat storage and thermal stability. - Abstract: The heat storage and phase transition behavior of a series of poly(vinyl alcohol)-g-octadecanol copolymers (PVA-g-C18OH) with apparent grafting ratios ranging from 283 to 503%, synthesized through “grafting to” method, has been investigated by Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), wide-angle X-ray diffraction (WAXD) and polarized optical microscopy (POM). PVA-g-C18OH copolymers exhibit the better thermal stability against C18OH, and the thermal energy storage ability (ΔH m ) is of dependence on the apparent grafting ratios. Compared with C18OH, the lower thermal storage efficiency possible is attributed to the less CH 2 groups entered into the crystalline domains and the frustrated mobility of the grafted C18 alkyl side chains between PVA backbones. The results show that

Preparation of Thermoplastic Poly (vinyl Alcohol), Ethylene Vinyl Acetate and Vinyl Acetate Versatic Ester Blends for Exterior Masonry Coating

International Nuclear Information System (INIS)

EL-Nahas, H.H.; Gad, Y.H.; Magida, M.M.

2013-01-01

Blend systems including ethylene vinyl acetate (EVA), poly (vinyl alcohol) (PVA) and vinyl acetate versatic copolymer latex (VAcVe) were prepared and used as exterior coatings. Mechanical and thermal properties of the blends were investigated using a testo meter, shore hardness tester, thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). The water resistance of the samples was measured. Effect of ionizing irradiation on gel content, tensile strength and surface hardness were also followed. The blend offers binder base for exterior masonry coating systems having superior water resistant and mechanical properties

Topological and morphological analysis of gamma rays irradiated chitosan-poly (vinyl alcohol) blends using atomic force microscopy

Science.gov (United States)

Bhatt, Rinkesh; Bisen, D. S.; Bajpai, R.; Bajpai, A. K.

2017-04-01

In the present communication, binary blends of poly (vinyl alcohol) (PVA) and chitosan (CS) were prepared by solution cast method and the roughness parameters of PVA, native CS and CS-PVA blend films were determined using atomic force microscopy (AFM). Moreover, the changes in the morphology of the samples were also investigated after irradiation of gamma rays at absorbed dose of 1 Mrad and 10 Mrad for the scanning areas of 5×5 μm2, 10×10 μm2 and 20×20 μm2. Amplitude, statistical and spatial parameters, including line, 3D and 2D image profiles of the experimental surfaces were examined and compared to un-irradiated samples. For gamma irradiated CS-PVA blends the larger waviness over the surface was found as compared to un-irradiated CS-PVA blends but the values of average roughness for both the films were found almost same. The coefficient of skewness was positive for gamma irradiated CS-PVA blends which revealed the presence of more peaks than valleys on the blend surfaces.

In vitro mechanical fatigue behavior of poly-ɛ-caprolactone macroporous scaffolds for cartilage tissue engineering: Influence of pore filling by a poly(vinyl alcohol) gel.

Science.gov (United States)

Panadero, J A; Vikingsson, L; Gomez Ribelles, J L; Lanceros-Mendez, S; Sencadas, V

2015-07-01

Polymeric scaffolds used in regenerative therapies are implanted in the damaged tissue and submitted to repeated loading cycles. In the case of articular cartilage engineering, an implanted scaffold is typically subjected to long-term dynamic compression. The evolution of the mechanical properties of the scaffold during bioresorption has been deeply studied in the past, but the possibility of failure due to mechanical fatigue has not been properly addressed. Nevertheless, the macroporous scaffold is susceptible to failure after repeated loading-unloading cycles. In this work fatigue studies of polycaprolactone scaffolds were carried by subjecting the scaffold to repeated compression cycles in conditions simulating the scaffold implanted in the articular cartilage. The behavior of the polycaprolactone sponge with the pores filled with a poly(vinyl alcohol) gel simulating the new formed tissue within the pores was compared with that of the material immersed in water. Results were analyzed with Morrow's criteria for failure and accurate fittings are obtained just up to 200 loading cycles. It is also shown that the presence of poly(vinyl alcohol) increases the elastic modulus of the scaffolds, the effect being more pronounced with increasing the number of freeze/thawing cycles. © 2014 Wiley Periodicals, Inc.

Precursor concentration and temperature controlled formation of polyvinyl alcohol-capped CdSe-quantum dots

Directory of Open Access Journals (Sweden)

Chetan P. Shah

2010-12-01

Full Text Available Polyvinyl alcohol-capped CdSe quantum dots, with a size within their quantum confinement limit, were prepared in aqueous solution at room temperature, by a simple and environmentally friendly chemical method. The size of the CdSe quantum dots was found to be dependent on the concentrations of the precursors of cadmium and selenium ions, as well as on the aging time and the reaction temperature; all of which could be used conveniently for tuning the size of the particles, as well as their optical properties. The synthesized quantum dots were characterized by optical absorption spectroscopy, fluorescence spectroscopy, X-ray diffraction, atomic force microscopy and transmission electron microscopy. The samples were fluorescent at room temperature; the green fluorescence was assigned to band edge emission, and the near-infrared fluorescence peaks at about 665 and 865 nm were assigned to shallow and deep trap states emissions, respectively. The quantum dots were fairly stable up to several days.

Therapeutic-Ultrasound-Triggered Shape Memory of a Melamine-Enhanced Poly(vinyl alcohol) Physical Hydrogel.

Science.gov (United States)

Li, Guo; Yan, Qiang; Xia, Hesheng; Zhao, Yue

2015-06-10

Therapeutic-ultrasound-triggered shape memory was demonstrated for the first time with a melamine-enhanced poly(vinyl alcohol) (PVA) physical hydrogel. The addition of a small amount of melamine (up to 1.5 wt %) in PVA results in a strong hydrogel due to the multiple H-bonding between the two constituents. A temporary shape of the hydrogel can be obtained by deformation of the hydrogel (∼65 wt % water) at room temperature, followed by fixation of the deformation by freezing/thawing the hydrogel under strain, which induces crystallization of PVA. We show that the ultrasound delivered by a commercially available device designed for the patient's pain relief could trigger the shape recovery process as a result of ultrasound-induced local heating in the hydrogel that melts the crystallized PVA cross-linking. This hydrogel is thus interesting for potential applications because it combines many desirable properties, being mechanically strong, biocompatible, and self-healable and displaying the shape memory capability triggered by a physiological stimulus.

Drying Shrinkage Behaviour of Fibre Reinforced Concrete Incorporating Polyvinyl Alcohol Fibres and Fly Ash

Directory of Open Access Journals (Sweden)

Amin Noushini

2014-01-01

Full Text Available The current study assesses the drying shrinkage behaviour of polyvinyl alcohol fibre reinforced concrete (PVA-FRC containing short-length (6 mm and long-length (12 mm uncoated monofilament PVA fibres at 0.125%, 0.25%, 0.375%, and 0.5% volumetric fractions. Fly ash is also used as a partial replacement of Portland cement in all mixes. PVA-FRC mixes have been compared to length change of control concrete (devoid of fibres at 3 storage intervals: early-age (0–7 days, short-term (0–28 days, and long-term (28–112 days intervals. The shrinkage results of FRC and control concrete up to 112 days indicated that all PVA-FRC mixes exhibited higher drying shrinkage than control. The shrinkage exhibited by PVA-FRC mixes ranged from 449 to 480 microstrain, where this value was only 427 microstrain in the case of control. In addition, the longer fibres exhibited higher mass loss, thus potentially contributing to higher shrinkage.

Water vapor permeation and dehumidification performance of poly(vinyl alcohol)/lithium chloride composite membranes

KAUST Repository

Bui, Duc Thuan

2015-10-09

Thin and robust composite membranes comprising stainless steel scaffold, fine and porous TiO2 and polyvinyl alcohol/lithium chloride were fabricated and studied for air dehumidification application. Higher hydrophilicity, sorption and permeation were observed for membranes with increased lithium chloride content up to 50%. The permeation and sorption properties of the membranes were investigated under different temperatures. The results provided a deeper insight into the membrane water vapor permeation process. It was specifically noted that lithium chloride significantly reduces water diffusion energy barrier, resulting in the change of permeation energy from positive to negative values. Higher water vapor permeance was observed for the membrane with higher LiCl content at lower temperature. The isothermal air dehumidification tests show that the membrane is suitable for dehumidifying air in high humid condition. Additionally, results also indicate a trade-off between the humidity ratio drop with the water vapor removal rate when varying air flowrate.

Assimilation of NH₄Br in Polyvinyl Alcohol/Poly(N-vinyl pyrrolidone) Polymer Blend-Based Electrolyte and Its Effect on Ionic Conductivity.

Science.gov (United States)

Parameswaran, V; Nallamuthu, N; Devendran, P; Manikandan, A; Nagarajan, E R

2018-06-01

Biodegradable polymer blend electrolyte based on ammonium based salt in variation composition consisting of PVA:PVP were prepared by using solution casting technique. The obtained films have been analyzed by various technical methods like as XRD, FT-IR, TG-DSC, SEM analysis and impedance spectroscopy. The XRD and FT-IR analysis exposed the amorphous nature and structural properties of the complex formation between PVA/PVP/NH4Br. Impedance spectroscopy analysis revealed the ionic conductivity and the dielectric properties of PVA/PVP/NH4Br polymer blend electrolyte films. The maximum ionic conductivity was determined to be 6.14 × 10-5 Scm-1 for the composition of 50%PVA: 50%PVP: 10% NH4Br with low activation energy 0.3457 eV at room temperature. Solid state battery is fabricated using highest ionic conducting polymer blend as electrolyte with the configuration Zn/ZnSO4 · 7H2O (anode) ∥ 50%PVA: 50%PVP: 10% NH4Br ∥ Mn2O3 (cathode). The observed open circuit voltage is 1.2 V and its performance has been studied.

In vitro cytotoxicity of iron oxide nanoparticles: effects of chitosan and polyvinyl alcohol as stabilizing agents

Science.gov (United States)

Tran, Phong A.; Nguyen, Hiep T.; Fox, Kate; Tran, Nhiem

2018-03-01

Iron oxide magnetic nanoparticles have significant potential in biomedical applications such as in diagnosis, imaging and therapeutic agent delivery. The choice of stabilizers and surface functionalization is important as it is known to strongly influence the cytotoxicity of the nanoparticles. The present study aimed at investigating the effects of surface charges on the cytotoxicity of iron oxide nanoparticles. We used a co-precipitation method to synthesize iron oxide nanoparticles which were then stabilized with either chitosan (CS) or polyvinyl alcohol (PVA) which have net positive charge and zero charge at physiological pH, respectively. The nanoparticles were characterized in terms of size, charges and chemical oxidation state. Cytotoxicity of the nanoparticles was assessed using mouse fibroblast cells and was correlated with surface charges of the nanoparticles and their aggregation.

Influence of UV and Gamma radiations on the induced birefringence of stretched poly(vinyl) alcohol foils

Science.gov (United States)

Nechifor, Cristina-Delia; Zelinschi, Carmen Beatrice; Dorohoi, Dana-Ortansa

2014-03-01

The aim of our paper is to evidence the influence of Gamma and UV radiations on the induced birefringence of poly(vinyl alcohol) stretched foils. Thin foils of PVA were prepared and dried without modifying their surfaces. The polymeric foils were irradiated from 15 min to 6 h using UV and Gamma radiations. The induced by stretching under heating birefringence of PVA films was measured at λ = 589.3 nm with a Babinet Compensator. Physico-chemical processes (photo stabilization, photo degradation, oxidation) induced by irradiation of polymer matrix influence both the stretching degree and the anisotropy of etired foils. An increase of birefringence versus the stretching ratio of the PVA foils was evidenced for all studied samples. The dependence of the birefringence on the exposure time, stretching ratio and nature of radiation was also confirmed.

Self-assembled amphiphilic polyhedral oligosilsesquioxane (POSS) grafted poly(vinyl alcohol) (PVA) nanoparticles

International Nuclear Information System (INIS)

Sheikh, Faheem A.; Barakat, Nasser A.M.; Kim, Byoung-Suhk; Aryal, Santosh; Khil, Myung-Seob; Kim, Hak-Yong

2009-01-01

In the present study, spherical nanoparticles (NPs) containing polyhedral oligosilsesquioxane (POSS) as an inner hydrophobic core and poly(vinyl alcohol) PVA as a hydrophilic outer shell were prepared by dialysis approach. Preparation of amphiphilic POSS-grafted-PVA co-polymer was characterized by 1 H NMR and FT-IR. The results indicated urethane linkage between monoisocyanate group of POSS macromer and the hydroxyl groups of PVA. The dynamic light scattering (DLS) and electrophoretic light scattering (ELS) of the NPs revealed that they have an average hydrodynamic diameter and negative zeta (ζ)-potential of 215 nm and - 161 mV, respectively. Atomic force microscopy (AFM) and bio-transmission electron microscope (BIO-TEM) have shown unagglomerated NPs within a diameter range of 60-90 nm. The prepared NPs were investigated to improve the control release of anticancer drug; paclitaxel as a model drug. Due to drug loading, the hydrodynamic diameter and negative zeta (ζ)-potential have changed to 325 nm and - 14 mV, respectively. In addition, in-vitro drug release experiments were conducted; the obtained results explicated continuous release for over 40 days. However, in case of using pure drug only, the drug completely released within 1 h.

Raman vibrational spectra of thymol blue dyed polyvinyl alcohol (PVA) film dosimeters

International Nuclear Information System (INIS)

Lepit, A.; Saion, E.B.; Susilawati; Doyan, A.; Wan Yusoff, W.M.D.

2002-01-01

Radiation-sensitive dyed polyvinyl alcohol (PVA) film indicators containing chloral hydrate and acid-sensitive thymol blue dye have been studied for routine food irradiation dosimeters. The free standing dyed film dosimeters of different chloral hydrate concentrations (0.1, 0.5, 1.0, 2.0 and 2.5 g) were irradiated with the absorbed dose ranges from 1 kGy to 12 kGy using gamma rays from Co-60 teletherapy. Upon exposure the dosimeters undergo chemical change and become more acidic, resulting in colour change from yellow to red at the critical doses depending on the chloral hydrate concentrations. The radiation-induced change in colour was analysed using UV-Vis spectrometer that the absorption spectra produced two maximal of the visible bands peaking at 445 nm for low doses and 554 nm for high doses. Spectra of inelastic Raman scattering photons corresponding to Raman shift frequency of unirradiated and irradiated films were measured using a dispersive Raman spectrometer. The spectral intensity of C=C, C-0 and S-H molecular vibration peaks for their respective Raman shifts were studied which provide the dose response to the change of dye molecular structure of the dosimeters. (Author)

Topological and morphological analysis of gamma rays irradiated chitosan-poly (vinyl alcohol) blends using atomic force microscopy

International Nuclear Information System (INIS)

Bhatt, Rinkesh; Bisen, D.S.; Bajpai, R.; Bajpai, A.K.

2017-01-01

In the present communication, binary blends of poly (vinyl alcohol) (PVA) and chitosan (CS) were prepared by solution cast method and the roughness parameters of PVA, native CS and CS-PVA blend films were determined using atomic force microscopy (AFM). Moreover, the changes in the morphology of the samples were also investigated after irradiation of gamma rays at absorbed dose of 1 Mrad and 10 Mrad for the scanning areas of 5×5 µm 2 , 10×10 µm 2 and 20×20 µm 2 . Amplitude, statistical and spatial parameters, including line, 3D and 2D image profiles of the experimental surfaces were examined and compared to un-irradiated samples. For gamma irradiated CS-PVA blends the larger waviness over the surface was found as compared to un-irradiated CS-PVA blends but the values of average roughness for both the films were found almost same. The coefficient of skewness was positive for gamma irradiated CS-PVA blends which revealed the presence of more peaks than valleys on the blend surfaces. - Highlights: • Binary polymer blends of chitosan and PVA were prepared. • Irradiation by gamma rays exhibited a significant change in surface morphology. • Various topographical and morphological parameters were investigated. • The prepared irradiated blends may find biomedical applications.

The effect of plasticiser on the properties of radiation crosslinked poly(vinyl chloride)

International Nuclear Information System (INIS)

Jamaliah Shariff; Roslin Abu Bakar

1996-01-01

A study on the effects of plasticizers in the crosslinking of poly(vinyl chloride), PVC, by an electron beam irradiation was carried out. Different types of plasticizers were used and these, with other additives, were blended with PVC in a Brabender mixer. The blended compound was the irradiated with high energy electron beam. Subsequent analysis of its properties showed that the efficiency of crosslinking was better in the presence of the adipate and trimellitate. The tensile and elongation properties were acceptable. The ageing properties of the compounds with adipate and trimellitate-type plasticizers showed encouraging results

In vitro characterization of polyvinyl alcohol assisted hydroxyapatite derived by sol–gel method

Energy Technology Data Exchange (ETDEWEB)

Kaygili, Omer, E-mail: okaygili@firat.edu.tr [Department of Physics, Faculty of Science, Firat University, 23119 Elazig (Turkey); Keser, Serhat [Department of Chemistry, Faculty of Science, Firat University, 23119 Elazig (Turkey); Al Orainy, R.H. [Physics Department, Sciences of Faculty for Girls, King Abdulaziz University, Jeddah (Saudi Arabia); Ates, Tankut [Department of Physics, Faculty of Science, Firat University, 23119 Elazig (Turkey); Yakuphanoglu, Fahrettin [Department of Physics, Faculty of Science, Firat University, 23119 Elazig (Turkey); Physics Department, Sciences of Faculty for Girls, King Abdulaziz University, Jeddah (Saudi Arabia)

2014-02-01

The synthesis and characterization of sol–gel derived hydroxyapatite (HAp) were investigated with the effects of the addition of polyvinyl alcohol (PVA) to the structural and material in vitro behavior. All samples were soaked in simulated body fluid (SBF) for 14 and 28 days. The characterization of bioceramics before and after immersing in SBF was carried out by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, differential thermal analysis (DTA), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) techniques. After the simulated body fluid period, the crystal structure and phase of HAp samples did not change significantly. The characteristic bands of hydroxyl, phosphate and carbonate groups were detected. HAp exhibited a thermal stability of room temperature to 1000 °C. The surface morphologies of the samples show an evident change with the soaking period in SBF. - Highlights: • The soaking period in SBF affects the surface morphology. • The Ca/P molar ratios change with the immersion time. • The as-prepared samples thermally stable from ∼ 25 to 1000 °C.

In vitro characterization of polyvinyl alcohol assisted hydroxyapatite derived by sol–gel method

International Nuclear Information System (INIS)

Kaygili, Omer; Keser, Serhat; Al Orainy, R.H.; Ates, Tankut; Yakuphanoglu, Fahrettin

2014-01-01

The synthesis and characterization of sol–gel derived hydroxyapatite (HAp) were investigated with the effects of the addition of polyvinyl alcohol (PVA) to the structural and material in vitro behavior. All samples were soaked in simulated body fluid (SBF) for 14 and 28 days. The characterization of bioceramics before and after immersing in SBF was carried out by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, differential thermal analysis (DTA), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) techniques. After the simulated body fluid period, the crystal structure and phase of HAp samples did not change significantly. The characteristic bands of hydroxyl, phosphate and carbonate groups were detected. HAp exhibited a thermal stability of room temperature to 1000 °C. The surface morphologies of the samples show an evident change with the soaking period in SBF. - Highlights: • The soaking period in SBF affects the surface morphology. • The Ca/P molar ratios change with the immersion time. • The as-prepared samples thermally stable from ∼ 25 to 1000 °C

Surface studies of microcrystalline chitosan/poly(vinyl alcohol) mixtures

Energy Technology Data Exchange (ETDEWEB)

Lewandowska, Katarzyna, E-mail: reol@chem.uni.torun.pl [Nicolaus Copernicus University, Faculty of Chemistry, Chair of Chemistry and Photochemistry of Polymers, 7 Gagarin Street, 87-100 Torun (Poland)

2012-12-15

Highlights: Black-Right-Pointing-Pointer The surface properties were investigated by AFM, SEM and FTIR. Black-Right-Pointing-Pointer The AFM images showed the lamellar structure of PVA in the blend. Black-Right-Pointing-Pointer SEM microscopy confirmed the existence of microphase separation of components. Black-Right-Pointing-Pointer FTIR analysis showed the existence of a weak interaction. - Abstract: In the present study, the surface properties of microcrystalline chitosan (MCCh), poly(vinyl alcohol) (PVA) and MCCh/PVA blends (made from acetic acid solutions with the MCCh concentration ranging from 20% to 80%) have been studied by the tapping-mode atomic force microscopy (AFM), scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. The changes of topography images are considered by determining the root mean square (RMS, R{sub q}) deviation in the image data. For PVA samples, the transition between adjacent lamellae occurs through holes, islands, and bicontinuous structures. The AFM images showed also the lamellar structure of PVA in the blend. The crystalline topography of MCCh/PVA film surface suggests the presence of PVA on the top surface. The FTIR spectra of film blends, in the amide I and II region of MCCh and the hydroxyl stretching bands of PVA have been analyzed. FTIR analysis showed the existence of a weak interaction of the hydroxyl or amino groups of microcrystalline chitosan with hydroxyl groups of PVA.

Surface studies of microcrystalline chitosan/poly(vinyl alcohol) mixtures

International Nuclear Information System (INIS)

Lewandowska, Katarzyna

2012-01-01

Highlights: ► The surface properties were investigated by AFM, SEM and FTIR. ► The AFM images showed the lamellar structure of PVA in the blend. ► SEM microscopy confirmed the existence of microphase separation of components. ► FTIR analysis showed the existence of a weak interaction. - Abstract: In the present study, the surface properties of microcrystalline chitosan (MCCh), poly(vinyl alcohol) (PVA) and MCCh/PVA blends (made from acetic acid solutions with the MCCh concentration ranging from 20% to 80%) have been studied by the tapping-mode atomic force microscopy (AFM), scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. The changes of topography images are considered by determining the root mean square (RMS, R q ) deviation in the image data. For PVA samples, the transition between adjacent lamellae occurs through holes, islands, and bicontinuous structures. The AFM images showed also the lamellar structure of PVA in the blend. The crystalline topography of MCCh/PVA film surface suggests the presence of PVA on the top surface. The FTIR spectra of film blends, in the amide I and II region of MCCh and the hydroxyl stretching bands of PVA have been analyzed. FTIR analysis showed the existence of a weak interaction of the hydroxyl or amino groups of microcrystalline chitosan with hydroxyl groups of PVA.

Effects of Partial Replacement of Eggshell Powder by Halloysite Nanotubes on the Properties of Polyvinyl Alcohol Composites

Science.gov (United States)

Alias, N. F.; Ismail, H.

2018-06-01

Polyvinyl alcohol (PVA)/eggshell powder (ESP) were prepared via solution casting method. The effects of gradual replacement of ESP by halloysite nanotubes (HNTs) were investigated based on tensile properties, physical properties and biodegradability. The main objective is to study the effect of hybrid fillers and also to compare the properties of PVA/ESP composite with conventional filler, HNT. The tensile properties decreased with increasing HNT loading. Scanning electron microscopy (SEM) studies showed that agglomeration of filler were present throughout the composites. Due to the presence of hydroxyl group on the outer and inner surface of HNT, the water absorption and water vapor transmisibility were found to increase with increasing HNTs loading. The biodegradability of film filled with HNT is lower compared to the film filled with ESP.

Mechanical and electro-rheological properties of electrospun poly(vinyl alcohol) nanofibre mats filled with carbon black nanoparticles

International Nuclear Information System (INIS)

Chuangchote, Surawut; Sirivat, Anuvat; Supaphol, Pitt

2007-01-01

The present contribution reports, for the first time, the mechanical and electro-rheological properties of electrospun poly(vinyl alcohol) (PVA) nanofibre mats with or without the incorporation of carbon black (CB) nanoparticles. The effects of sonication and the addition of CB on morphological appearance, average diameter of the as-spun fibre mats, and that of the individual fibres, were thoroughly investigated. Incorporation of CB (1-10% based on the weight of PVA) in 10% w/v PVA solution did not affect the morphology and average diameter of the obtained fibres (∼160 nm), but it affected both the mechanical and the electro-rheological properties of the as-spun PVA/CB fibre mats, in which the mats became more rigid with the addition and increasing amount of CB

Poly(aniline-co-m-aminobenzoic acid) deposited on poly(vinyl ...

Indian Academy of Sciences (India)

Abstract. In this work, we have deposited poly(aniline-co-m-aminobenzoic acid) on poly(vinyl alcohol) (PVA) by in situ ... along the polyaniline (PANI) chain results in self dop- ing of PANI and ..... The value of electrical conductivity is found to be ...

Investigation of Electrospun Poly Vinyl Alcohol Fibers Towards the Development of Manufacturable Wound Dressings

Science.gov (United States)

Vora, Asad

Polymers such as polyvinyl alcohol, chitosan, and starch have excellent bio-compatible and bio-degradable properties. Their applications in drug delivery, wound dressings, artificial cartilage materials have increased dramatically due to their much sought-after renewable and biological properties. Hence, polyvinyl alcohol has been chosen for this study to test the feasibility of polyvinyl alcohol nanofibers towards the manufacturable wound dressings. Polyvinyl alcohol nanofibers are prepared via electrospinning technique, where different wt% polyvinyl alcohol solutions are prepared. The fibers were optimized by varying important electrospninning parameters which include voltage applied, the collector-needle distance and flow rate. Morphology and structure of the electrospun fibers are analysed using scanning electron microscopy and fourier transform infrared respectively. The diameter of fibers obtained was found to be in the range of 100 nm-160 nm. Thermal stability was examined using DSC and TGA characterization technique and fibers are found to be stable up to 220oC. Finally, each weight sample of PVA fibers are analysed by goniometer for wettability and is found to be hydrophilic.

Structural analysis of poly(vinyl alcohol hydrogels) produced by freezing and thawing process Positron annihilation lifetime spectroscopy (PALS)

International Nuclear Information System (INIS)

Paranhos, Caio M.; Oliveira, Renata N.; Soares, Bluma G.

2005-01-01

In this work, poly(vinyl alcohol) hydrogels with a entrapped polyelectrolyte were characterized through Positron Annihilation Lifetime Spectroscopy (PALS). PALS was used to determine the average pore radii (R), average free volume (V f ) and the intensity of ortho-positronium (I 3 ). The free volume estimated for the hydrogels increases with increasing polyelectrolyte content, while the intensity of o-Ps decreases with the increasing polyelectrolyte content. Degree of crystallinity of the samples decreases with the presence of polyelectrolyte. The structural changes observed can be discussed in terms of the changes in hydrogels structure due to a hindrance capacity of the polyelectrolyte on the crystalline behavior and the different polymer-polymer interactions. (author)

Repeated courses of transarterial embolization with polyvinyl alcohol particles: 'long life elixir' in a cirrhotic patient with unresectable hepatocellular carcinoma.

Science.gov (United States)

Marelli, Laura; Shusang, Vibhakorn; Senzolo, Marco; Cholongitas, Evangelos; Goode, Antony; Yu, Dominic; Patch, David W; Burroughs, Andrew K

2007-04-01

Chemoembolization improves survival in selected cirrhotic patients with hepatocellular carcinoma, but prolonged survival is unusual. In this study, a 70-year-old cirrhotic patient, who had a histologically proven hepatocellular carcinoma of 5 cm diameter, embolization with polyvinyl alcohol particles alone, without chemotherapeutic agent, has resulted in continued survival, of 5 years to date, with virtual elimination of residual hypervascularity following 10 sessions of embolization, and with continued patency of the injected branch of the hepatic artery. Provided liver function is maintained, embolization alone appears a feasible long term and effective therapy for unresectable hepatocellular carcinoma.

Methylene blue doped polymers: efficient media for optical recording

Science.gov (United States)

Ushamani, M.; Sreekumar, K.; Sudha Kartha, C.; Joseph, R.

2004-05-01

Polymer materials find application in optical storage technology, namely in the development of high information density and fast access type memories. A new polymer blend of methylene blue sensitized polyvinyl alcohol (PVA) and polyacrylic acid (PAA) in methanol is prepared and characterized and its comparison with methylene blue sensitized PVA in methanol and complexed methylene blue sensitized polyvinyl chloride (CMBPVC) is presented. The optical absorption spectra of the thin films of these polymers showed a strong and broad absorption region at 670-650 nm, matching the wavelength of the laser used. A very slow recovery of the dye on irradiation was observed when a 7:3 blend of polyvinyl alcohol/polyacrylic acid at a pH of 3.8 and a sensitizer concentration of 4.67 · 10-5 g/ml were used. A diffraction efficiency of up to 20% was observed for the MBPVA/alcohol system and an energetic sensitivity of 2000 mJ/cm2 was obtained in the photosensitive films with a spatial frequency of 588 lines/mm.

Functionalized SiC nanocrystals for tuning of optical, thermal, mechanical and electrical properties of polyvinyl alcohol

DEFF Research Database (Denmark)

Saini, Isha; Sharma, Annu; Dhiman, Rajnish

2017-01-01

 MPa for PVA to 45 MPa for PVA-SiC nanocomposite film containing 0.023 wt% f-SiC nanocrystals at an applied load of 9.8 mN indicating improved interfacial interaction. Current-voltage analysis indicated an increase in conductivity of PVA with the introduction of f-SiC nanocrystals. The conduction......Polyvinyl alcohol (PVA)-SiC nanocomposite films were prepared by incorporating functionalized Silicon Carbide (f-SiC) nanocrystals in PVA matrix. Structural characterization of SiC nanocrystals before and after the functionalization was carried out using Fourier transform infrared spectroscopy...... (FTIR), X-ray diffraction (XRD) and Thermogravimetric analysis (TGA). Transmission electron microscopy (TEM) and Scanning Electron Microscopy (SEM) were used to study the morphology and size distribution of f-SiC nanocrystals in PVA-SiC nanocomposite films. TEM and SEM images depict an improved...

Compatibility of polyvinyl alcohol and poly(methyl vinyl ether-co-maleic acid) blends estimated by molecular dynamics

CSIR Research Space (South Africa)

Moolman, FS

2005-07-25

Full Text Available are not dissociated (ionized). At pH below pKa (negative logarithm of acid dissociation constant) of maleic acid (first and second dissociation constants at 25 8C are pKa1Z1.91 and pKa 2Z6.33, respectively [22]), ioniz- ation of the carboxylic acid groups in the PMVE...-MA. Decreasing pH also reduces absolute viscosities and broadens the optimum blend ratio peak. Fig. 2. Density of a selected number of runs (11?15) as a function of time. F.S. Moolman et al. / Polymer 46 (2005) 6192?6200 6195 The cohesive energy densities display...

Sonochemical synthesis of PVA/PVP blend nanocomposite containing modified CuO nanoparticles with vitamin B1 and their antibacterial activity against Staphylococcus aureus and Escherichia coli.

Science.gov (United States)

Mallakpour, Shadpour; Mansourzadeh, Soheila

2018-05-01

The aim of this paper was to blend the polymers, poly(N-vinyl-2-pyrrolidone) (PVP) and poly(vinyl alcohol) (PVA) to produce a novel composite materials possessing the benefits of both. CuO nanoparticles (NPs) were used as a suitable filler to fabricate the blend nanocomposites (NCs) with desired properties. First, the surface of NPs, was modified with vitamin B 1 (VB 1 ) as a bio-safe coupling agent. Then, the blend NCs with various ratios of modified CuO (3, 5, and 7 wt%) were fabricated under ultrasonic irradiations followed by casting/solvent evaporation method. These processes are fast and green way to disperse the NPs sufficiently. Several techniques were applied for the characterization of the obtained NCs. morphology examination demonstrated the morphology of NCs and compatibility of NPs with the blend polymer. EDX results indicated the weight and atomic percentage of the achieved materials. TGA analysis verified that the NCs show higher thermal properties than the neat blend polymer. Also embedding the modified NPs into the blend polymer had effected on optical absorbance of the obtained NCs. The contact angle measurements confirmed that the hydrophilicity decreased for different proportions of the modified NPs loaded in the blend polymer. Finally, NCs show better bactericidal effects against gram-positive than gram-negative bacteria. Copyright © 2018 Elsevier B.V. All rights reserved.

Alcohols/Ethers as Oxygenates in Diesel Fuel: Properties of Blended Fuels and Evaluation of Practiacl Experiences

Energy Technology Data Exchange (ETDEWEB)

Nylund, N.; Aakko, P. [TEC Trans Energy Consulting Ltd (Finland); Niemi, S.; Paanu, T. [Turku Polytechnic (Finland); Berg, R. [Befri Konsult (Sweden)

2005-03-15

Oxygenates blended into diesel fuel can serve at least two purposes. Components based on renewable feedstocks make it possible to introduce a renewable component into diesel fuel. Secondly, oxygenates blended into diesel fuel might help to reduce emissions. A number of different oxygenates have been considered as components for diesel fuel. These oxygenates include various alcohols, ethers, esters and carbonates. Of the oxygenates, ethanol is the most common and almost all practical experiences have been generated from the use of diesel/ethanol blends (E-diesel). Biodiesel was not included in this study. Adding ethanol to diesel will reduce cetane, and therefore, both cetane improver and lubricity additives might be needed. Diesel/ethanol emulsions obtained with emulsifiers or without additives are 'milky' mixtures. Micro-emulsions of ethanol and diesel can be obtained using additives containing surfactants or co-solvents. The microemulsions are chemically and thermodynamically stable, they are clear and bright blends, unlike the emulsions. Storage and handling regulations for fuels are based on the flash point. The problem with, e.g., ethanol into diesel is that ethanol lowers the flash point of the blend significantly even at low concentrations. Regarding safety, diesel-ethanol blends fall into the same category as gasoline. Higher alcohols are more suitable for diesel blending than ethanol. Currently, various standards and specifications set rather tight limits for diesel fuel composition and properties. It should be noted that, e.g., E-diesel does not fulfil any current diesel specification and it cannot, thus, be sold as general diesel fuel. Some blends have already received approvals for special applications. The critical factors of the potential commercial use of these blends include blend properties such as stability, viscosity and lubricity, safety and materials compatibility. The effect of the fuel on engine performance, durability and emissions

Alcohols/Ethers as Oxygenates in Diesel Fuel: Properties of Blended Fuels and Evaluation of Practiacl Experiences

Energy Technology Data Exchange (ETDEWEB)

Nylund, N; Aakko, P [TEC Trans Energy Consulting Ltd (Finland); Niemi, S; Paanu, T [Turku Polytechnic (Finland); Berg, R [Befri Konsult (Sweden)

2005-03-15

Oxygenates blended into diesel fuel can serve at least two purposes. Components based on renewable feedstocks make it possible to introduce a renewable component into diesel fuel. Secondly, oxygenates blended into diesel fuel might help to reduce emissions. A number of different oxygenates have been considered as components for diesel fuel. These oxygenates include various alcohols, ethers, esters and carbonates. Of the oxygenates, ethanol is the most common and almost all practical experiences have been generated from the use of diesel/ethanol blends (E-diesel). Biodiesel was not included in this study. Adding ethanol to diesel will reduce cetane, and therefore, both cetane improver and lubricity additives might be needed. Diesel/ethanol emulsions obtained with emulsifiers or without additives are 'milky' mixtures. Micro-emulsions of ethanol and diesel can be obtained using additives containing surfactants or co-solvents. The microemulsions are chemically and thermodynamically stable, they are clear and bright blends, unlike the emulsions. Storage and handling regulations for fuels are based on the flash point. The problem with, e.g., ethanol into diesel is that ethanol lowers the flash point of the blend significantly even at low concentrations. Regarding safety, diesel-ethanol blends fall into the same category as gasoline. Higher alcohols are more suitable for diesel blending than ethanol. Currently, various standards and specifications set rather tight limits for diesel fuel composition and properties. It should be noted that, e.g., E-diesel does not fulfil any current diesel specification and it cannot, thus, be sold as general diesel fuel. Some blends have already received approvals for special applications. The critical factors of the potential commercial use of these blends include blend properties such as stability, viscosity and lubricity, safety and materials compatibility. The effect of the fuel on engine performance, durability and emissions is also

Removal and adsorption characteristics of polyvinyl alcohol from aqueous solutions using electrocoagulation

Energy Technology Data Exchange (ETDEWEB)

Chou, Wei-Lung, E-mail: wlchou@sunrise.hk.edu.tw [Department of Safety, Health and Environmental Engineering, Hungkuang University, Sha-Lu, Taichung 433, Taiwan (China)

2010-05-15

The study was to investigate the performance of electrocoagulation (EC) for the efficient removal of polyvinyl alcohol (PVA) from aqueous solutions. Several parameters were evaluated to characterize the PVA removal efficiency, such as various electrode pairs, current densities, supporting electrolytes, temperatures, and initial electrolyte concentrations. The effects of the current density, supporting electrolyte, and temperature on the electrical energy consumption were also investigated. The experimental results indicate that a Fe/Al electrode pair is the optimum choice out of four different electrode pair combinations. The optimum current density, supporting electrolyte concentration, and temperature were found to be 5 mA cm{sup -2}, 0.008N NaCl, and 298 K, respectively. The PVA removal efficiency decreased with increasing in the initial concentrations. The kinetic studies indicated that the EC process was best described using pseudo-second-order kinetics. The experimental data were also compared to different adsorption isotherm models in order to describe the EC process. The adsorption of PVA was best fitted by the Langmuir adsorption isotherm model. Thermodynamic parameters such as the Gibbs free energy, enthalpy, and entropy indicated that the adsorption of PVA on metal hydroxides was feasible, spontaneous and endothermic in the temperature range of 288-318 K.

Removal and adsorption characteristics of polyvinyl alcohol from aqueous solutions using electrocoagulation

International Nuclear Information System (INIS)

Chou, Wei-Lung

2010-01-01

The study was to investigate the performance of electrocoagulation (EC) for the efficient removal of polyvinyl alcohol (PVA) from aqueous solutions. Several parameters were evaluated to characterize the PVA removal efficiency, such as various electrode pairs, current densities, supporting electrolytes, temperatures, and initial electrolyte concentrations. The effects of the current density, supporting electrolyte, and temperature on the electrical energy consumption were also investigated. The experimental results indicate that a Fe/Al electrode pair is the optimum choice out of four different electrode pair combinations. The optimum current density, supporting electrolyte concentration, and temperature were found to be 5 mA cm -2 , 0.008N NaCl, and 298 K, respectively. The PVA removal efficiency decreased with increasing in the initial concentrations. The kinetic studies indicated that the EC process was best described using pseudo-second-order kinetics. The experimental data were also compared to different adsorption isotherm models in order to describe the EC process. The adsorption of PVA was best fitted by the Langmuir adsorption isotherm model. Thermodynamic parameters such as the Gibbs free energy, enthalpy, and entropy indicated that the adsorption of PVA on metal hydroxides was feasible, spontaneous and endothermic in the temperature range of 288-318 K.

Effect of trap states and microstructure on charge carrier conduction mechanism through semicrystalline poly(vinyl alcohol) granular film

Science.gov (United States)

Das, A. K.; Bhowmik, R. N.; Meikap, A. K.

2018-05-01

We report a comprehensive study on hysteresis behaviour of current-voltage characteristic and impedance spectroscopy of granular semicrystalline poly(vinyl alcohol) (PVA) film. The charge carrier conduction mechanism and charge traps of granular PVA film by measuring and analyzing the temperature dependent current-voltage characteristic indicate a bi-stable electronic state in the film. A sharp transformation of charge carrier conduction mechanism from Poole-Frenkel emission to space charge limited current mechanism has been observed. An anomalous oscillatory behaviour of current has been observed due to electric pulse effect on the molecular chain of the polymer. Effect of microstructure on charge transport mechanism has been investigated from impedance spectroscopy analysis. An equivalent circuit model has been proposed to explain the result.

Alanine/epr pellet dosimeter using poly(vinyl butyral-co-vinyl alcohol-co-vinyl acetate) copolymer as a binder for radiation dosimetry

International Nuclear Information System (INIS)

Beshir, W.B.; Ezz El-Din, H.M.; Abdel-fatth, A.A.; Ebraheem, S.

2005-01-01

A new alanine pellet dosimeter was developed for gamma and electron beam radiation dosimetry. Alanine powder was mixed with a new binding material, poly(vinyl butyral-co-vinyl alcohol-co-vinyl acetate) copolymer. Pellets were prepared by pressing fine powder alanine with 60% copolymer binder by using hydraulic press and a specially designed pressing die. The radiation-formed stable free radicals were analysed by using electron paramagnetic resonance (EPR) spectroscopy. The useful dose range of these pellets was found to ranges from 1 to 80 kGy. The stability of the radiation- induced response was also studied

A polyacrylamide-based silica stationary phase for the separation of carbohydrates using alcohols as the weak eluent in hydrophilic interaction liquid chromatography.

Science.gov (United States)

Cai, Jianfeng; Cheng, Lingping; Zhao, Jianchao; Fu, Qing; Jin, Yu; Ke, Yanxiong; Liang, Xinmiao

2017-11-17

A hydrophilic interaction liquid chromatography (HILIC) stationary phase was prepared by a two-step synthesis method, immobilizing polyacrylamide on silica sphere particles. The stationary phase (named PA, 5μm dia) was evaluated using a mixture of carbohydrates in HILIC mode and the column efficiency reached 121,000Nm -1 . The retention behavior of carbohydrates on PA stationary phase was investigated with three different organic solvents (acetonitrile, ethanol and methanol) employed as the weak eluent. The strongest hydrophilicity of PA stationary phase was observed in both acetonitrile and methanol as the weak eluent, when compared with another two amide stationary phases. Attributing to its high hydrophilicity, three oligosaccharides (xylooligosaccharide, fructooligosaccharide and chitooligosaccharides) presented good retention on PA stationary phase using alcohols/water as mobile phase. Finally, PA stationary phase was successfully applied for the purification of galactooligosaccharides and saponins of Paris polyphylla. It is feasible to use safer and cheaper alcohols to replace acetonitrile as the weak eluent for green analysis and purification of polar compounds on PA stationary phase. Copyright © 2017. Published by Elsevier B.V.

Quaternized poly(vinyl alcohol)/alumina composite polymer membranes for alkaline direct methanol fuel cells

Science.gov (United States)

Yang, Chun-Chen; Chiu, Shwu-Jer; Chien, Wen-Chen; Chiu, Sheng-Shin

The quaternized poly(vinyl alcohol)/alumina (designated as QPVA/Al 2O 3) nanocomposite polymer membrane was prepared by a solution casting method. The characteristic properties of the QPVA/Al 2O 3 nanocomposite polymer membranes were investigated using thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), dynamic mechanical analysis (DMA), micro-Raman spectroscopy, and AC impedance method. Alkaline direct methanol fuel cell (ADMFC) comprised of the QPVA/Al 2O 3 nanocomposite polymer membrane were assembled and examined. Experimental results indicate that the DMFC employing a cheap non-perfluorinated (QPVA/Al 2O 3) nanocomposite polymer membrane shows excellent electrochemical performances. The peak power densities of the DMFC with 4 M KOH + 1 M CH 3OH, 2 M CH 3OH, and 4 M CH 3OH solutions are 28.33, 32.40, and 36.15 mW cm -2, respectively, at room temperature and in ambient air. The QPVA/Al 2O 3 nanocomposite polymer membranes constitute a viable candidate for applications on alkaline DMFC.

Study on Chitosan-Polyvinyl Alcohol Inter polymeric ph-Responsive Hydrogels for Controlled Drug Delivery

International Nuclear Information System (INIS)

Abdel-Bary, E.M.; El-Sherbiny, I.M.; Abdelaal, M.Y.; Abdel-Razik, E.A.

2005-01-01

Two series of ph-responsive biodegradable interpenetrating polymeric (IPN) hydrogels composed of chitosan and poly(vinyl alcohol) (PVA) were prepared for controlled drug release investigations. The first series was chemically crosslinked with different concentrations of glutaraldehyde as a crosslinked and the second series was crosslinked by gamma-radiation. Degree of crosslinking has been controlled by the concentration of crosslinked as well as by gamma irradiation dose. The equilibrium swelling -reflecting the degree of crosslinks - were carried out for the gels at 37 degree C in buffer solutions of ph 2.1 and 7.4 (simulated gastric and intestinal fluids respectively). 5-fluorouracil (5- FU) was entrapped, as a model therapeutic agent, in the hydrogels and equilibrium-swelling studies were carried out for the drug-entrapped gels at 37 degree C. The in-vitro release profiles of the drug were established at 37 degree C in ph 2.1 and 7.4. FT-IR was employed to investigate the structural changes of the gels with different degrees of crosslinking

Tm-doped fiber laser mode-locking with MoS2-polyvinyl alcohol saturable absorber

Science.gov (United States)

Cao, Liming; Li, Xing; Zhang, Rui; Wu, Duanduan; Dai, Shixun; Peng, Jian; Weng, Jian; Nie, Qiuhua

2018-03-01

We have designed an all-fiber passive mode-locking thulium-doped fiber laser that uses molybdenum disulfide (MoS2) as a saturable absorber (SA) material. A free-standing few-layer MoS2-polyvinyl alcohol (PVA) film is fabricated by liquid phase exfoliation (LPE) and is then transferred onto the end face of a fiber connector. The excellent saturable absorption of the fabricated MoS2-based SA allows the laser to output soliton pulses at a pump power of 500 mW. Fundamental frequency mode-locking is realized at a repetition frequency of 13.9 MHz. The central wavelength is 1926 nm, the 3 dB spectral bandwidth is 2.86 nm and the pulse duration is 1.51 ps. Additionally, third-order harmonic mode-locking of the laser is also achieved. The pulse duration is 1.33 ps, which is slightly narrower than the fundamental frequency mode-locking bandwidth. The experimental results demonstrate that the few-layer MoS2-PVA SA is promising for use in 2 μm laser systems.

A Review of Natural Fiber Reinforced Poly(Vinyl Alcohol Based Composites: Application and Opportunity

Directory of Open Access Journals (Sweden)

Boon Khoon Tan

2015-11-01

Full Text Available Natural fibers are fine examples of renewable resources that play an important role in the composites industry, which produces superior strength comparable to synthetic fibers. Poly(vinyl alcohol (PVA composites in particular have attracted enormous interest in view of their satisfactory performance, properties and biodegradability. Their performance in many applications such as consumer, biomedical, and agriculture is well defined and promising. This paper reviews the utilization of natural fibers from macro to nanoscale as reinforcement in PVA composites. An overview on the properties, processing methods, biodegradability, and applications of these composites is presented. The advantages arising from chemical and physical modifications of fibers or composites are discussed in terms of improved properties and performance. In addition, proper arrangement of nanocellulose in composites helps to prevent agglomeration and results in a better dispersion. The limitations and challenges of the composites and future works of these bio-composites are also discussed. This review concludes that PVA composites have potential for use in numerous applications. However, issues on technological feasibility, environmental effectiveness, and economic affordability should be considered.

Properties of poly(vinyl alcohol)–borax gel doped with neodymium ...

Indian Academy of Sciences (India)

visible region then leads to luminescent emission in the near infra-red region. The spectral qualities of the ... molecular hydrogen bonding between the hydroxyl groups on poly(vinyl ..... mately results in near IR emissions. The maximum of the.

Polyvinyl chloride resin

International Nuclear Information System (INIS)

Kim, Hong Jae

1976-06-01

This book contains polyvinyl chloride resin industry with present condition such as plastic industry and polyvinyl chloride in the world and Japan, manufacture of polyvinyl chloride resin ; suspension polymerization and solution polymerization, extruding, injection process, hollow molding vinyl record, vacuum forming, polymer powders process, vinyl chloride varnish, vinyl chloride latex, safety and construction on vinyl chloride. Each chapter has descriptions on of process and kinds of polyvinyl chloride resin.

Preparation of poly(vinyl alcohol)-grafted graphene oxide/poly(vinyl alcohol) nanocomposites via in-situ low-temperature emulsion polymerization and their thermal and mechanical characterization

Energy Technology Data Exchange (ETDEWEB)

Zhang, Shengchang; Liu, Pengqing, E-mail: liupq@scu.edu.cn; Zhao, Xiangsen; Xu, Jianjun, E-mail: xujj@scu.edu.cn

2017-02-28

Highlights: • In-situ emulsion polymerization and alcoholysis reaction is a good method to prepare GO/PVA nanocomposites. • Surface chemical grafting modification of GO with PVA chains was also carried out during the in-situ emulsion polymerization and alcoholysis reaction. • The surface chemical grafting modification of GO by in-situ polymerization and alcoholysis reaction could not only improve the dispersion of fillers in matrix, but also the interfacial interactions between fillers and matrix. • The thermal and mechanical properties of PVA-g-GO/PVA nanocompistes were also studied. - Abstract: An in-situ polymerization combined with chemical grafting modification method for preparing Poly(vinyl alcohol)-grafted graphene oxide/Poly(vinyl alcohol) (PVA-g-GO/PVA) nanocomposites was reported. Firstly, Poly(vinyl acetate)-grafted graphene oxide/Poly(vinyl acetate) nanocomposites were prepared, and then the PVA-g-GO/PVA nanocomposites could be obtained through alcoholysis reaction. X-ray photoelectron spectrometer and fourier-transform infrared spectrometer confirmed that the PVAc or PVA chains were successfully grafted to GO sheets during in-situ polymerization and alcoholysis. And the results from transmission electron microscopy, scanning electron microscopy and X-ray diffraction showed that the well compatibility and homogenous dispersion of PVA-g-GO in PVA matrix could be achieved. Differential scanning calorimetric, thermogravimetry analysis and tensile test were employed to study the thermal and mechanical properties of the PVA-g-GO/PVA nanocomposites. The results indicated that a 53% improvement of tensile strength and a 36% improvement of Young’s modulus were achieved by addition of 0.5 wt% of GO sheets. And the glass transition temperature of PVA-g-GO/PVA nanocomposites was increased, and their thermal stability and crystallization degree were both decreased. Due to well dispersion of fillers and strong interfacial interactions at the filler

Preparation of poly(vinyl alcohol)-grafted graphene oxide/poly(vinyl alcohol) nanocomposites via in-situ low-temperature emulsion polymerization and their thermal and mechanical characterization

International Nuclear Information System (INIS)

Zhang, Shengchang; Liu, Pengqing; Zhao, Xiangsen; Xu, Jianjun

2017-01-01

Highlights: • In-situ emulsion polymerization and alcoholysis reaction is a good method to prepare GO/PVA nanocomposites. • Surface chemical grafting modification of GO with PVA chains was also carried out during the in-situ emulsion polymerization and alcoholysis reaction. • The surface chemical grafting modification of GO by in-situ polymerization and alcoholysis reaction could not only improve the dispersion of fillers in matrix, but also the interfacial interactions between fillers and matrix. • The thermal and mechanical properties of PVA-g-GO/PVA nanocompistes were also studied. - Abstract: An in-situ polymerization combined with chemical grafting modification method for preparing Poly(vinyl alcohol)-grafted graphene oxide/Poly(vinyl alcohol) (PVA-g-GO/PVA) nanocomposites was reported. Firstly, Poly(vinyl acetate)-grafted graphene oxide/Poly(vinyl acetate) nanocomposites were prepared, and then the PVA-g-GO/PVA nanocomposites could be obtained through alcoholysis reaction. X-ray photoelectron spectrometer and fourier-transform infrared spectrometer confirmed that the PVAc or PVA chains were successfully grafted to GO sheets during in-situ polymerization and alcoholysis. And the results from transmission electron microscopy, scanning electron microscopy and X-ray diffraction showed that the well compatibility and homogenous dispersion of PVA-g-GO in PVA matrix could be achieved. Differential scanning calorimetric, thermogravimetry analysis and tensile test were employed to study the thermal and mechanical properties of the PVA-g-GO/PVA nanocomposites. The results indicated that a 53% improvement of tensile strength and a 36% improvement of Young’s modulus were achieved by addition of 0.5 wt% of GO sheets. And the glass transition temperature of PVA-g-GO/PVA nanocomposites was increased, and their thermal stability and crystallization degree were both decreased. Due to well dispersion of fillers and strong interfacial interactions at the filler

醇类-汽油混合燃料的喷雾特性%Spray Characteristics of Various Alcohol-Gasoline Blends

Institute of Scientific and Technical Information of China (English)

何邦全; 都成君

2012-01-01

The spray characteristics and fuel injection rate of a multi-hole injector of a direct injection gasoline engine were investigated on test benches when the alcohol-gasoline blends containing 10% and 30% volume fraction of etha-nol, 10% and 30% volume fraction of n-butanol and their base gasoline were used, respectively. The results show that, with the increase of injection pressure, the transient fuel injection rates of alcohol-gasoline blends increase, and their variations are dependent on the fuels tested. In the meantime, spray penetration of various fuels increases with injection pressure, and the differences of individual spray image at the same time in a single injection increase. The spray penetration of alcohol-gasoline blends is close to that of gasoline at high ambient pressure. The spray cone angles of different fuels after the initial stage of injection are much affected by ambient pressure in the constant chamber. At low ambient pressure, the spray cone angles of gasoline are greater than those of alcohol-gasoline blends. On the contrary, at high ambient pressure, the spray cone angles of alcohol-gasoline blends are bigger than those of gasoline except the case in which the blends containing 30% volume fraction of ethanol are used.%在试验台上,研究了使用汽油醇类混合燃料,其中醇类燃料体积分数分别为10％的乙醇-汽油、30％的乙醇-汽油、10％的正丁醇-汽油和30％的正丁醇-汽油时,直喷汽油机多孔喷油器的喷油率和喷雾特性.结果表明,随着喷油压力的提高,醇类-汽油混合燃料的瞬时喷油率增大,且瞬时喷油率波动性依赖于燃料.同时,喷油压力的提高使得喷雾贯穿距离加大,单次喷油后同一时刻的喷雾差异性变大.在�

Poly(vinyl-alcohol)/poly(ethylene-glycol)/poly(ethylene-imine) blend membranes - structure and CO2 facilitated transport

International Nuclear Information System (INIS)

Ben Hamouda, S.; Quang, Trong Nguyen; Langevin, D.; Sadok, Roudeslic

2010-01-01

Poly(vinyl-alcohol) (PVA)/poly(ethylene-imine) (PEI)/poly(ethylene-glycol) (PEG) blend membranes were prepared by solution casting followed by solvent evaporation. The effects of the blend polymer composition on the membrane structure and CO 2 /N 2 permeation characteristics were investigated. IR spectroscopy evidenced strong hydrogen bonding interactions between amorphous PVA and PEI, and weaker interactions between PVA and PEG. DSC studies showed that PVA crystallization was partially inhibited by the interactions between amorphous PVA and PEI blend, in which PEG separated into nodules. The CO 2 permeability decreased with an increase in CO 2 partial pressure in feed gas, while the N 2 permeability remained constant. This result indicated that only CO 2 was transported by the facilitated transport mechanism. The CO 2 and N 2 permeabilities increased monotonically with the PEI content in the blend membranes, whereas the ideal selectivity of CO 2 to N 2 transport showed a maximum. When CO 2 is humidified, its permeability through the blend membranes is much higher than that of dry CO 2 , but the change in permeability due to the presence of humidity is reversible. (authors)

Combination of maghemite and titanium oxide nanoparticles in polyvinyl alcohol-alginate encapsulated beads for cadmium ions removal

Energy Technology Data Exchange (ETDEWEB)

Majidnia, Zohreh; Idris, Ani [Universiti Teknologi Malaysia, johor bahru (Malaysia)

2015-06-15

Both maghemite (γ-Fe{sub 2}O{sub 3}) and titanium oxide (TiO{sub 2}) nanoparticles were mixed at various ratios and embedded in polyvinyl alcohol (PVA)-alginate beads. These beads were tested for photocatalytic behavior in eliminating toxic Cd(Ⅱ) from the aqueous solution. The photocatalytic experiments were performed under sunlight irradiation at various pH, initial feed concentrations and γ-Fe{sub 2}O{sub 3}: TiO{sub 2} ratios. The recycling attribute of these beads was also investigated. The results revealed that 100% of the Cd(Ⅱ) was eliminated in 150 minutes at pH 7 under sunlight. It shows that maghemite and titania PVA-alginate beads can be readily isolated from the aqueous solution after the photocatalyst process and reused for at least six times without losing their initial properties.

Synthesis and characterization of particles derived of poly(vinyl alcohol) (PVA) for treatment of embolization and chemoembolization

International Nuclear Information System (INIS)

Semenzim, Vinicius L.; Basso, Glaucia G.; Passos, Rodrigo A.; Nery, Jose G.; Agreli, Guilherme; Oliveira, Ana P.M.L.; Kawasaki-Oyama, Rosa S.; Braile, Domingo M.

2009-01-01

The most effective way to treat cancerous tumors is by surgically removing them. However in some types of cancer, such as liver and uterine cancer, more than two-thirds of patients have no indication for surgery due to the size and location of the tumor, such as into the blood vessels. Doctors and researchers have invested in alternative and less invasive methods such as chemoembolization. The objectives of this research project are the synthesis and characterization of poly(vinyl alcohol) (PVA) particles for use in cancer treatment. PVA particles will be combined with chemotherapeutic agent Doxorubicin, drug commonly used in the treatment of cancers and carcinomas. The particles, obtained by controlled polymerization reaction followed by saponification, were characterized by SEM, XRD and NMR-CP/MAS. The functionalization of the particles with the drug is the next step of this study. (author)

Investigation on the thermal properties of new thermo-reversible networks based on poly(vinyl furfural and multifunctional maleimide compounds

Directory of Open Access Journals (Sweden)

C. Gaina

2012-02-01

Full Text Available New thermo-reversible networks were obtained from poly(vinyl furfural and multifunctional maleimide monomers by Diels-Alder (DA and retro-DA reactions. The poly(vinyl furfural having acetalization degree of 15 and 25% were obtained by the acid-catalyzed homogenous acetalization of poly(vinyl alcohol with 2-furfural in a nonaqueous media. The thermal and viscoelastic behaviour of the cross-linked materials have been studied via differential scanning calorimetry, dynamic mechanical analysis and thermogravimetric analysis. The networks exhibit considerable swelling in those organic solvents that dissolve both poly(vinyl furfural and bismaleimides; by heating in aprotic dipolar solvents at 150°C, they become soluble.

Tailoring the properties of thermoplastic starch by blending with cinnamyl alcohol and radiation processing: An insight into the competitive grafting and scission reactions

International Nuclear Information System (INIS)

Khandal, Dhriti; Mikus, Pierre-Yves; Dole, Patrice; Bliard, Christophe; Soulestin, Jérémie; Lacrampe, Marie-France; Baumberger, Stéphanie; Coqueret, Xavier

2012-01-01

The present paper focuses on the effects of electron beam (EB) irradiation on thermoplastic materials based on destructurized starch including glycerol and water as plasticizers to assess the potentiality of cinnamyl alcohol as reactive additive capable of counterbalancing the degradation of the polysaccharide by inducing interchain covalent linkages. The tensile properties at break of test specimens of controlled composition submitted to EB irradiation at doses ranging from 50 to 200 kGy revealed the presence of competitive chain scission and bridging in samples containing cinnamyl alcohol at a relative concentration of 2.5% with regard to dry starch. The occurrence of crosslinking under particular conditions was evidenced by gel fraction measurements. The treatment under radiation was also applied to model blends including maltodextrin as a model for starch and the other ingredients to gain an insight into the radiation induced mechanisms at the molecular level. The presence of cinnamyl alcohol is found to limit degradation. Size exclusion chromatography and gel fraction allowed to monitor the effects and confirmed unambiguously the attachment of UV-absorbing chromophores onto the maltodextrin main chain. The combination of the obtained results demonstrates the possibility of altering in a favorable way the tensile properties of plasticized starch by applying high energy radiation to properly formulated blends including aromatic compounds like cinnamyl alcohol. - Highlights: ► Assessment of the potentiality of cinnamyl alcohol as an additive capable of counterbalancing the degradation of the polysaccharide. ► Tensile properties of test specimens of controlled composition submitted to EB irradiation revealed the presence of competitive chain scission and bridging in samples containing 2.5 wt% cinnamyl alcohol. ► Gel fraction measurements confirmed that grafting was overcoming chain scission. ► Possibility of altering in a favorable way the tensile

In-Vitro Release of Ketoprofen Behavior Loaded in Polyvinyl Alcohol / Acrylamide Hydrogels Prepared by Gamma Irradiation

International Nuclear Information System (INIS)

Mahmoud, Gh.A.; Hegazy, D.E.; Kamal, H.

2014-01-01

Hydrogels based on various ratios of polyvinyl alcohol (PVA) and acrylamide (AAm) were prepared by gamma radiation. The formed hydrogels were characterized by spectroscopic analysis (FTIR), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and swelling studied. It was found that the thermal stability of the hydrogel decreases as the AAm content increases in the hydrogel. The higher the AAm content in the hydrogel, the lower the values of Tm and ΔH m . Ketoprofen was adopted as a model drug to study the adsorption and release behavior of (PVA/AAm) hydrogel. The drug adsorption was decreased by increasing AAm ratio in the hydrogel. From the in vitro drug release study in ph progressive media, the basic medium was showed comparatively the highest release and the (PVA/AAm) hydrogel of composition (70/30) was found to be the highest release one. The mechanism of Ketoprofen release from the (PVA/AAm) matrix was found to be non-Fickian mechanism for all investigated hydrogels at ph 7.

Molecular modeling studies of structural properties of polyvinyl alcohol: a comparative study using INTERFACE force field.

Science.gov (United States)

Radosinski, Lukasz; Labus, Karolina

2017-10-05

Polyvinyl alcohol (PVA) is a material with a variety of applications in separation, biotechnology, and biomedicine. Using combined Monte Carlo and molecular dynamics techniques, we present an extensive comparative study of second- and third-generation force fields Universal, COMPASS, COMPASS II, PCFF, and the newly developed INTERFACE, as applied to this system. In particular, we show that an INTERFACE force field provides a possibility of composing a reliable atomistic model to reproduce density change of PVA matrix in a narrow temperature range (298-348 K) and calculate a thermal expansion coefficient with reasonable accuracy. Thus, the INTERFACE force field may be used to predict mechanical properties of the PVA system, being a scaffold for hydrogels, with much greater accuracy than latter approaches. Graphical abstract Molecular Dynamics and Monte Carlo studies indicate that it is possible to predict properties of the PVA in narrow temperature range by using the INTERFACE force field.

Mucoadhesive polymers: Synthesis and in vitro characterization of thiolated poly(vinyl alcohol).

Science.gov (United States)

Suchaoin, Wongsakorn; Pereira de Sousa, Irene; Netsomboon, Kesinee; Rohrer, Julia; Hoffmann Abad, Patricia; Laffleur, Flavia; Matuszczak, Barbara; Bernkop-Schnürch, Andreas

2016-04-30

The aim of this study was to synthesize thiolated poly(vinyl alcohol) (PVA) and to evaluate its mucoadhesive properties. Thiourea and 3-mercaptopropionic acid were utilized in order to obtain thiolated PVAs, namely, TPVA1 and TPVA2, respectively. TPVA1 and TPVA2 displayed 130.44 ± 14.99 and 958.35 ± 155.27 μmol immobilized thiol groups per gram polymer, respectively, which were then evaluated regarding reactivity of thiol groups, swelling behavior and mucoadhesive properties. Both thiolated PVAs exhibited the highest reactivity at pH 8.0 whereas more than 95% of free thiol groups were preserved at pH 5.0. Thiolation of PVA decelerated water uptake and prolonged disintegration time of test discs compared to unmodified PVA. Contact time of TPVA1- and TPVA2-based test discs on porcine intestinal mucosa was 3.2- and 15.8-fold prolonged, respectively, in comparison to non-thiolated PVA as measured by rotating cylinder method. According to tensile studies on mucosa, the total work of adhesion (TWA) and the maximum detachment force (MDF) were increased when compared to PVA. Furthermore, thiolated PVAs preserved higher percentage of viable cells compared to unmodified PVA within 24h as evaluated by MTT assay. Accordingly, thiolated PVA represents a novel excipient that can likely improve the mucoadhesive properties of various pharmaceutical formulations. Copyright © 2016 Elsevier B.V. All rights reserved.

Conductive, tough, hydrophilic poly(vinyl alcohol)/graphene hybrid fibers for wearable supercapacitors

Science.gov (United States)

Chen, Shaohua; Ma, Wujun; Xiang, Hengxue; Cheng, Yanhua; Yang, Shengyuan; Weng, Wei; Zhu, Meifang

2016-07-01

Graphene fibers based flexible supercapacitors have great potential as wearable power sources for textile electronics. However, their electrochemical performance is limited by the serious stacking of graphene sheets and their hydrophobicity in aqueous electrolytes. Meanwhile, their brittleness is unfavorable for practical application. Incorporation of nanofillers into graphene fibers has been proved effective for enhancing their capacitance, whereas often leading to deteriorated mechanical strength. Herein we demonstrate that the strength, toughness and capacitive performance of graphene-based fibers can be significantly enhanced simultaneously, simply by incorporating hydrophilic poly(vinyl alcohol) (PVA) into a non-liquid-crystalline graphene oxide (GO) dispersion before wet spinning and chemical reduction. The structure and properties of the resulted PVA/graphene hybrid fibers are systematically investigated, and the mechanism behind these enhancements is discussed in detail. The hybrid fiber with a PVA/GO weight ratio of 10/90 possesses a strength of 186 MPa, a toughness of 11.3 J cm-3, and a capacitance of 241 F cm-3 in 1 M H2SO4. A solid-state yarn supercapacitor assembled from these fibers exhibits a device energy of 5.97 mW h cm-3, and features excellent flexibility and bending stability. This device is robust enough to be integrated into textile and thus promising as wearable power supply for smart textiles.

Plasmon-enhanced luminescence of Sm complex using silver nanoparticles in Polyvinyl Alcohol

Energy Technology Data Exchange (ETDEWEB)

Kaur, Gagandeep; Verma, R.K.; Rai, D.K. [Laser and Spectroscopy Laboratory, Department of Physics, Banaras Hindu University, India 221005 (India); Rai, S.B., E-mail: sbrai49@yahoo.co.in [Laser and Spectroscopy Laboratory, Department of Physics, Banaras Hindu University, India 221005 (India)

2012-07-15

Silver (Ag) nanoparticles (NPs) were prepared by laser ablation in water with an aim to enhance the luminescence of rare earth coordinated complex in polymer host. A fixed concentration of the complex containing Samarium (Sm), Salicylic acid (Sal) and 1, 10-phenanthroline (Phen) were combined with different concentrations of silver NPs in PolyVinyl Alcohol at room temperature. Absorption spectrum and XRD patterns of the sample show that the Sm(Sal){sub 3}Phen complex is accompanied by Ag NPs. The luminescence from the complex was recorded in the presence and absence of Ag NPs using two different excitation wavelengths viz. 400 and 355 nm. Of these, 400 nm radiation falls in the surface plasmon resonance of Ag NPs. It was found that the Ag NPs led to a significant enhancement in luminescence of the complex. Surprisingly, a high concentration of Ag NPs tends to quench the luminescence. - Highlights: Black-Right-Pointing-Pointer Sm complex with Ag nanoparticles in PVA was prepared at room temperature. Black-Right-Pointing-Pointer UV-vis absorption and XRD confirms the presence of Sm complex and Ag NPs. Black-Right-Pointing-Pointer Enhancement in luminescence of complex was observed with Ag NPs. Black-Right-Pointing-Pointer Coupling between radiative transitions of Sm and SPR of NPs enhances the emission. Black-Right-Pointing-Pointer The higher concentration of Ag NPs quenches the luminescence of the complex.

Highly Zeolite-Loaded Polyvinyl Alcohol Composite Membranes for Alkaline Fuel-Cell Electrolytes

Directory of Open Access Journals (Sweden)

Po-Ya Hsu

2018-01-01

Full Text Available Having a secure and stable energy supply is a top priority for the global community. Fuel-cell technology is recognized as a promising electrical energy generation system for the twenty-first century. Polyvinyl alcohol/zeolitic imidazolate framework-8 (PVA/ZIF-8 composite membranes were successfully prepared in this work from direct ZIF-8 suspension solution (0–45.4 wt % and PVA mixing to prevent filler aggregation for direct methanol alkaline fuel cells (DMAFCs. The ZIF-8 fillers were chosen for the appropriate cavity size as a screening aid to allow water and suppress methanol transport. Increased ionic conductivities and suppressed methanol permeabilities were achieved for the PVA/40.5% ZIF-8 composites, compared to other samples. A high power density of 173.2 mW cm−2 was achieved using a KOH-doped PVA/40.5% ZIF-8 membrane in a DMAFC at 60 °C with 1–2 mg cm−2 catalyst loads. As the filler content was raised beyond 45.4 wt %, adverse effects resulted and the DMAFC performance (144.9 mW cm−2 was not improved further. Therefore, the optimal ZIF-8 content was approximately 40.5 wt % in the polymeric matrix. The specific power output was higher (58 mW mg−1 than most membranes reported in the literature (3–18 mW mg−1.

Preparation and characterization of poly(vinyl alcohol) hydrogel contain metronidazole by irradiation

Energy Technology Data Exchange (ETDEWEB)

Baik, Jae; Park, Jong Seok; Jeong, Jin Oh; Jeong, Sung In; Gwon, Hui Jeong; Ahn, Sung Jun; Lim, Youn Mook [Advanced Radiation Technology Institute, Korea Atomic Energy Research Institute, Jeongeup (Korea, Republic of)

2016-11-15

Periodontitis is disease of damaged gum tissue that is not removed the plaque onto teeth. In case that the symptoms of disease get pain worse, it will have to extract tooth because of tumefy or bleeding at gums so treatment of drug was required to periodontitis. In this study, the hydrogel was prepared by including superior viscous, excellent elastic, and biocompatibility of Poly(vinyl alcohol, PVA) and antimicrobial drug of Metronidazole (MD). The 15 wt% PVA was dissolved in deionized water and then prepared PVA solution was irradiated using gamma-ray at 25 kGy (10 kGy hr{sup -1}). In addition, PVA hydrogel was immersed in each 0.1, 0.25 and 0.5 wt% MD solution using stirrer for 24 hr. The result of the gelation, 0.5 wt% MD loaded PVA hydrogel (76%) was lower than PVA hydrogel (88.2%). The swelling ration of 0.5 wt% MD loaded PVA hydrogel (294.8%) was higher than PVA hydrogel (105.2%). The compressive strength and thermal properties of MD loaded PVA hydrogel was gradually lower. The drug release test of 0.5 wt% MD loaded PVA hydrogel (61%) was higher than 0.1 wt% MD loaded PVA hydrogel (12%). Therefore, MD loaded PVA hygrogel may be a promising tool for periodontitis medicine by gamma-ray.

Preparation and characterization of poly(vinyl alcohol) hydrogel contain metronidazole by irradiation

International Nuclear Information System (INIS)

Baik, Jae; Park, Jong Seok; Jeong, Jin Oh; Jeong, Sung In; Gwon, Hui Jeong; Ahn, Sung Jun; Lim, Youn Mook

2016-01-01

Periodontitis is disease of damaged gum tissue that is not removed the plaque onto teeth. In case that the symptoms of disease get pain worse, it will have to extract tooth because of tumefy or bleeding at gums so treatment of drug was required to periodontitis. In this study, the hydrogel was prepared by including superior viscous, excellent elastic, and biocompatibility of Poly(vinyl alcohol, PVA) and antimicrobial drug of Metronidazole (MD). The 15 wt% PVA was dissolved in deionized water and then prepared PVA solution was irradiated using gamma-ray at 25 kGy (10 kGy hr"-"1). In addition, PVA hydrogel was immersed in each 0.1, 0.25 and 0.5 wt% MD solution using stirrer for 24 hr. The result of the gelation, 0.5 wt% MD loaded PVA hydrogel (76%) was lower than PVA hydrogel (88.2%). The swelling ration of 0.5 wt% MD loaded PVA hydrogel (294.8%) was higher than PVA hydrogel (105.2%). The compressive strength and thermal properties of MD loaded PVA hydrogel was gradually lower. The drug release test of 0.5 wt% MD loaded PVA hydrogel (61%) was higher than 0.1 wt% MD loaded PVA hydrogel (12%). Therefore, MD loaded PVA hygrogel may be a promising tool for periodontitis medicine by gamma-ray

Application of water-soluble polyvinyl alcohol-based film patches on laser microporated skin facilitates intradermal macromolecule and nanoparticle delivery.

Science.gov (United States)

Engelke, Laura; Winter, Gerhard; Engert, Julia

2018-07-01

The intradermal delivery of biologics has long been recognized as attractive approach for cutaneous immunotherapy, particularly vaccination. Although intradermal (i.d.) or subcutaneous (s.c.) injection provide reproducible dosing and good cost- and delivery efficiency, the major objective to avoid sharps and the need for enhanced storage stability have renewed the interest in alternative needle-free delivery strategies. This study presents a new concept for the delivery of macromolecules and nanoparticles to viable skin layers with a high density of professional antigen-presenting cells (APCs). Stable polyvinyl alcohol (PVA) polymer films as well as PVA blends with carboxymethyl cellulose (CMC) or cross-linked carbomer were prepared using an easily-scalable film casting technique. Fluorescein isothiocyanate (FITC) and rhodamine B-labeled dextrane 70 kDa (RD70), used as small and macromolecular model substances, or polystyrene (PS)-nano- and microparticles with diameters of 0.5 µm and 5 µm were directly incorporated into the polymer formulations at varying concentrations. The assembly of the polymer films with an occlusive backing tape created a film patch that provided a fast drug release upon dissolution of the water-soluble film and facilitated an intradermal drug delivery on laser microporated skin. The minimally-invasive P.L.E.A.S.E.® laser poration system (Pantec Biosolutions, Ruggell, Liechtenstein) provided access to viable skin layers by thermally ablating the superficial tissue with a pulsed Er:YAG laser (λ = 2.94 µm). In our in vitro study using excised pig skin, laser microporation induced a 4- to 5-fold increase of water transport (TEWL) through excised skin in a Franz diffusion cell compared to intact skin. The TEWL values detected were comparable to in vivo human skin. The increased water transport facilitated the dissolution of all topically applied dry PVA-based film formulations within 6 h. No dissolution of the films was seen on

Flexible and strong ternary blends of poly(vinyl chloride), poly(butylene adipate)and nanoparticle-plasticizers

OpenAIRE

Yin, Bo; Hakkarainen, Minna

2013-01-01

Multiple property enhancement was achieved for ternary blends of PVC, poly(butylene adipate) (PBA) plasticizer and PBA-grafted nanofillers as compared to ternary blends with untreated nanofillers. The blends with surface modified halloysite, kaolin or silicon dioxide nanofillers all exhibited higher stress at break and higher strain at break as compared to the corresponding composites with untreated nanoparticles. The strain at break was similar or improved compared to binary PVC/PBA blends. ...

Short Oligonucleotides Aligned in Stretched Humid Matrix: Secondary DNA Structure in Poly(vinyl alcohol) Environment

KAUST Repository

Hanczyc, Piotr

2012-04-24

We report that short, synthetic, double- as well as single-stranded DNA can be aligned in stretched humid poly(vinyl alcohol) (PVA) matrix, and the secondary structure (nucleobase orientation) can be characterized with linear dichroism (LD) spectroscopy. Oligonucleotides of lengths varying between 10 (3.4 nm) and 60 bases (20.4 nm) were investigated with respect to structural properties in the gel-like polymer environment. The DNA conformation as a function of relative humidity reveals a strong dependence of helical structure of DNA on PVA hydration level, results of relevance for nanotechnical studies of DNA-based supramolecular systems. Also, the PVA gel could provide possibilities to test models for nucleic acid interactions and distribution in cell contexts, including structural stability of genetic material in the cell and PVA-packaging for gene delivery. A method by which duplex oligonucleotides, with sequences designed to provide specific binding sites, become amenable to polarized-light spectroscopy opens up new possibilities for studying structure in DNA complexes with small adduct molecules as well as proteins. © 2012 American Chemical Society.

Flame-retardant polyvinyl alcohol membrane with high transparency based on a reactive phosphorus-containing compound

Science.gov (United States)

Peng, Sha; Zhou, Ming; Liu, Feiyan; Zhang, Chang; Liu, Xueqing; Liu, Jiyan; Zou, Liyong; Chen, Jia

2017-08-01

Flame-retardant polyvinyl alcohol (PVA) membranes with high transparency and flexibility were prepared by mixing an aqueous solution of a phosphorus-containing acrylic acid (AOPA) with PVA. The reaction between AOPA and PVA, the transparency, the crystallinity and the flexibility of the membrane were investigated with Fourier transform infrared spectrometry (FTIR), UV-vis light transmittance, X-ray diffraction and tensile tests, respectively. The limited oxygen index (LOI) and vertical flame (UL 94 VTM), microscale combustion calorimetry, thermogravimetric analysis (TGA) and TGA-FTIR were employed to evaluate the flame retardancy as well as to reveal the corresponding mechanisms. Results showed that PVA containing 30 wt% of AOPA can reach the UL 94 VTM V0 rating with an LOI of 27.3% and retain 95% of the original transparency of pure PVA. Adding AOPA reduces crystallinity of PVA, while the flexibility is increased. AOPA depresses the thermal degradation of PVA and promotes char formation during combustion. The proposed decomposition mechanism indicates that AOPA acts mainly in the condensed phase.

Evaluation of polyvinyl alcohols as mucoadhesive polymers for mucoadhesive buccal tablets prepared by direct compression.

Science.gov (United States)

Ikeuchi-Takahashi, Yuri; Ishihara, Chizuko; Onishi, Hiraku

2017-09-01

The purpose of the present work was to evaluate polyvinyl alcohols (PVAs) as a mucoadhesive polymer for mucoadhesive buccal tablets prepared by direct compression. Various polymerization degree and particle diameter PVAs were investigated for their usability. The tensile strength, in vitro adhesive force, and water absorption properties of the tablets were determined to compare the various PVAs. The highest values of the tensile strength and the in vitro adhesive force were observed for PVAs with a medium viscosity and small particle size. The optimal PVA was identified by a factorial design analysis. Mucoadhesive tablets containing the optimal PVA were compared with carboxyvinyl polymer and hydroxypropyl cellulose formulations. The optimal PVA gives a high adhesive force, has a low viscosity, and resulted in relatively rapid drug release. Formulations containing carboxyvinyl polymer had high tensile strengths but short disintegration times. Higher hydroxypropyl cellulose concentration formulations had good adhesion forces and very long disintegration times. We identified the optimal characteristics of PVA, and the usefulness of mucoadhesive buccal tablets containing this PVA was suggested from their formulation properties.

Fabrication and mechanical characterization of a polyvinyl alcohol sponge for tissue engineering applications.

Science.gov (United States)

Karimi, A; Navidbakhsh, M; Faghihi, S

2014-05-01

Polyvinyl alcohol (PVA) sponges are widely used for clinical applications, including ophthalmic surgical treatments, wound healing and tissue engineering. There is, however, a lack of sufficient data on the mechanical properties of PVA sponges. In this study, a biomechanical method is used to characterize the elastic modulus, maximum stress and strain as well as the swelling ratio of a fabricated PVA sponge (P-sponge) and it is compared with two commercially available PVA sponges (CENEFOM and EYETEC). The results indicate that the elastic modulus of the P-sponge is 5.32% and 13.45% lower than that of the CENEFOM and EYETEC sponges, while it bears 4.11% more and 10.37% less stress compared to the CENEFOM and EYETEC sponges, respectively. The P-sponge shows a maximum strain of 32% more than the EYETEC sponge as well as a 26.78% higher swelling ratio, which is a significantly higher absorbency compared to the CENEFOM. It is believed that the results of this study would help for a better understanding of the extension, rupture and swelling mechanism of PVA sponges, which could lead to crucial improvement in the design and application of PVA-based materials in ophthalmic and plastic surgeries as well as wound healing and tissue engineering.

Influence of Uranium and Polivinyl Alcohol Concentration in the Feed of Sol Gel Process on the Gel Spherical Product

International Nuclear Information System (INIS)

Indra Suryawan; Endang Susiantini

2007-01-01

The gel particles have been made at various uranium and polyvinyl alcohol concentration in the sol gel process. The variables of uranium concentration were 0.3; 0.5; 0.7; 0.9; 1.1; 1.3; 1.5; 1.7; 1.9 and 2.1 M The variables of polyvinyl alcohol concentration were 0.3; 0.6; 0.9; 1.2; 1.5; 1.8; 2.1 and 2.4 M After drying the sol gel process products were heated at 300, 500 and 750°C during 4 hours. The gel particles were characterized using an optic microscope to know the shape and condition morphology of gel. From experimental result using uranium concentration of 0.3 until 2.1 M and polyvinyl alcohol of 1.8 until 2.4 M spherical and gel was formed elastic, after heating at 750°C it was unbreakable. At the concentration of polyvinyl alcohol from 0.3 to 0.5 M, the gel product was soft and broken after being dried. At the concentration of polyvinyl alcohol from 0.6 to 0.8 M, the dried gel product was not perfect. At the concentration of polyvinyl alcohol from 0.9 to 1.7 M, the gel product of gelation process was spherical and it was broken after being heated up to 300°C. (author)

Neutron spin-echo studies on dynamic and static fluctuations in two types of poly(vinyl alcohol) gels

International Nuclear Information System (INIS)

Kanaya, T.; Takahashi, N.; Nishida, K.; Seto, H.; Nagao, M.; Takeda, T.

2005-01-01

We report neutron spin-echo measurements on two types of poly(vinyl alcohol) (PVA) gels. The first is PVA gel in a mixture of dimethyl sulfoxide (DMSO) and water with volume ratio 60/40, and the second is PVA gel in an aqueous borax solution. The observed normalized intermediate scattering functions I(Q,t)/I(Q,0) are very different between them. The former I(Q,t)/I(Q,0) shows a nondecaying component in addition to a fast decay, but the latter does not have the nondecaying one. This clearly indicates that the fluctuations in the former PVA gel consist of static and dynamic fluctuations whereas the latter PVA gel does include only the dynamic fluctuations. The dynamic fluctuations of the former and latter gels have been analyzed in terms of a restricted motion in the network and Zimm motion, respectively, and the origins of these motions will be discussed

Poly(vinyl alcohol)-Tannic Acid Hydrogels with Excellent Mechanical Properties and Shape Memory Behaviors.

Science.gov (United States)

Chen, Ya-Nan; Peng, Lufang; Liu, Tianqi; Wang, Yaxin; Shi, Shengjie; Wang, Huiliang

2016-10-12

Shape memory hydrogels have promising applications in a wide variety of fields. Here we report the facile fabrication of a novel type of shape memory hydrogels physically cross-linked with both stronger and weaker hydrogen bonding (H-bonding). Strong multiple H-bonding formed between poly(vinyl alcohol) (PVA) and tannic acid (TA) leads to their coagulation when they are physically mixed at an elevated temperature and easy gelation at room temperature. The amorphous structure and strong H-bonding endow the PVA-TA hydrogels with excellent mechanical properties, as indicated by their high tensile strengths (up to 2.88 MPa) and high elongations (up to 1100%). The stronger H-bonding between PVA and TA functions as the "permanent" cross-link and the weaker H-bonding between PVA chains as the "temporary" cross-link. The reversible breakage and formation of the weaker H-bonding imparts the PVA-TA hydrogels with excellent temperature-responsive shape memory. Wet and dried hydrogel samples with a deformed or elongated shape can recover to their original shapes when immersed in 60 °C water in a few seconds or at 125 °C in about 2.5 min, respectively.

Borax mediated layer-by-layer self-assembly of neutral poly(vinyl alcohol) and chitosan.

Science.gov (United States)

Manna, Uttam; Patil, Satish

2009-07-09

We report a multilayer film of poly(vinyl alcohol) (PVA)-borate complex and chitosan by using a layer-by-layer approach. PVA is an uncharged polymer, but hydroxyl functional groups of PVA can be cross-linked by using borax as a cross-linking agent. As a result electrostatic charges and intra- and interchain cross-links are introduced in the PVA chain and provide physically cross-linked networks. The PVA-borate was then deposited on a flat substrate as well as on colloidal particles with chitosan as an oppositely charged polyelectrolyte. Quartz crystal microbalance, scanning electron microscopy, and atomic force microscopy were used to follow the growth of thin film on flat substrate. Analogous experiments were performed on melamine formaldehyde colloidal particles (3-3.5 microm) to quantify the process for the preparation of hollow microcapsules. Removal of the core in 0.1 N HCl results in hollow microcapsules. Characterization of microcapsules by transmission electron microscopy revealed formation of stable microcapsules. Further, self-assembly of PVA-borate/chitosan was loaded with the anticancer drug doxorubicin, and release rates were determined at different pH values to highlight the drug delivery potential of this system.

Proton exchange membrane developed from novel blends of polybenzimidazole and poly(vinyl-1,2,4-triazole).

Science.gov (United States)

Hazarika, Mousumi; Jana, Tushar

2012-10-24

In continuation (J. Phys. Chem. B2008, 112, 5305; J. Colloid Interface Sci. 2010, 351, 374) of our quest for proton exchange membrane (PEM) developed from polybenzimidazole (PBI) blends, novel polymer blend membranes of PBI and poly(1-vinyl-1,2,4-triazole) (PVT) were prepared using a solution blending method. The aim of the work was to investigate the effect of the blend composition on the properties, e.g., thermo-mechanical stability, swelling, and proton conductivity of the blend membranes. The presence of specific interactions between the two polymers in the blends were observed by studying the samples using varieties of spectroscopic techniques. Blends prepared in all possible compositions were studied using a differential scanning calorimetry (DSC) and exhibited a single T(g) value, which lies between the T(g) value of the neat polymers. The presence of a single composition-dependent T(g) value indicated that the blend is a miscible blend. The N-H···N interactions between the two polymers were found to be the driving force for the miscibility. Thermal stability up to 300 °C of the blend membranes, obtained from thermogravimetric analysis, ensured their suitability as PEMs for high-temperature fuel cells. The proton conductivity of the blend membranes have improved significantly, compared to neat PBI, because of the presence of triazole moiety, which acts as a proton facilitator in the conduction process. The blend membranes showed a considerably lower increase in thickness and swelling ratio than that of PBI after doping with phosphoric acid (PA). We found that the porous morphology of the blend membranes caused the loading of a larger amount of PA and, consequently, higher proton conduction with lower activation energy, compared to neat PBI.

Comparison of combustion characteristics of n-butanol/ethanol–gasoline blends in a HCCI engine

International Nuclear Information System (INIS)

He, Bang-Quan; Liu, Mao-Bin; Zhao, Hua

2015-01-01

Highlights: • The blends with alcohol autoignite early in the conditions highly diluted by exhaust. • n-Butanol is more reactive than ethanol in the blend with the same alcohol content. • Autoignition timing delays with retarding IVO timing for all alcohol–gasoline blends. • Advanced autoignition for the blends with alcohol leads to lower thermal efficiency. - Abstract: As a sustainable biofuel, n-butanol can be used in conventional spark ignition (SI) and compression ignition (CI) engines in order to reduce the dependence on fossil fuel. Homogeneous charge compression ignition (HCCI) is a novel combustion to improve the thermal efficiency of conventional SI engines at part loads. To understand the effect of alcohol structure on HCCI combustion under stoichiometric conditions highly diluted by exhaust gases, the combustion characteristics of n-butanol, ethanol and their blends with gasoline were investigated on a single cylinder port fuel injection gasoline engine with fixed intake/exhaust valve lifts at the same operating conditions in this study. The results show that autoignition timing for alcohol–gasoline blends is dependent on alcohol types and its concentration in the blend, engine speed and intake valve opening (IVO)/exhaust valve closing (EVC) timing. In the operating conditions with the residual gases more than 38% by mass in the mixture, alcohol–gasoline blends autoignite more easily than gasoline. Autoignition timing for n-butanol–gasoline blend is earlier than that for ethanol–gasoline blend with the same alcohol volume fraction at 1500 rpm in most cases while the autoignition timings for the blends with alcohol are relatively close at 2000 rpm at the same IVO/EVC timing. Combustion stability is improved with advanced EVC timing at a fixed IVO timing, which is benefit for the improvement in the thermal efficiency in the case of alcohol–gasoline blends. In addition, n-butanol–gasoline blends autoignite earlier than their ethanol�

27 CFR 24.213 - Heavy bodied blending wine.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Heavy bodied blending wine..., DEPARTMENT OF THE TREASURY LIQUORS WINE Production of Other Than Standard Wine § 24.213 Heavy bodied blending wine. Heavy bodied blending wine is wine made for blending purposes from grapes or other fruit without...

Synthesis of MoO3 and its polyvinyl alcohol nanostructured film

Indian Academy of Sciences (India)

Unknown

†Appa Institute of Engineering and Technology, Gulbarga 585 101, India. MS received 9 December ... The solvent casting method is adopted for the synthesis of MoO3 dispersed polyvinyl ... one dimension, are dispersed in an organic polymer matrix in order to .... applied for the synthesis of other layered ceramic materi- als.

Relative humidity sensor based on surface plasmon resonance of D-shaped fiber with polyvinyl alcohol embedding Au grating

Science.gov (United States)

Yan, Haitao; Han, Daofu; Li, Ming; Lin, Bo

2017-01-01

This paper presents the design, fabrication, and characterization of a D-shaped fiber coated with polyvinyl alcohol (PVA) embedding an Au grating-based relative humidity (RH) sensor. The Au grating is fabricated on a D-shaped fiber to match the wave-vector and excite the surface plasmon, and the PVA is embedded in the Au grating as a sensitive cladding film. The refractive index of PVA changes with the ambient humidity. Measurements in a controlled environment show that the RH sensor can achieve a sensitivity of 5.4 nm per relative humidity unit in the RH range from 0% to 70% RH. Moreover, the surface plasmon resonance can be realized and used for RH sensing at the C band of optical fiber communication instead of the visible light band due to the metallic grating microstructure on the D-shaped fiber.

Poly(vinyl alcohol) hydrogel coatings with tunable surface exposure of hydroxyapatite

Science.gov (United States)

Moreau, David; Villain, Arthur; Ku, David N; Corté, Laurent

2014-01-01

Insufficient bone anchoring is a major limitation of artificial substitutes for connective osteoarticular tissues. The use of coatings containing osseoconductive ceramic particles is one of the actively explored strategies to improve osseointegration and strengthen the bone-implant interface for general tissue engineering. Our hypothesis is that hydroxyapatite (HA) particles can be coated robustly on specific assemblies of PVA hydrogel fibers for the potential anchoring of ligament replacements. A simple dip-coating method is described to produce composite coatings made of microscopic hydroxyapatite (HA) particles dispersed in a poly(vinyl alcohol) (PVA) matrix. The materials are compatible with the requirements for implant Good Manufacturing Practices. They are applied to coat bundles of PVA hydrogel fibers used for the development of ligament implants. By means of optical and electronic microscopy, we show that the coating thickness and surface state can be adjusted by varying the composition of the dipping solution. Quantitative analysis based on backscattered electron microscopy show that the exposure of HA at the coating surface can be tuned from 0 to over 55% by decreasing the weight ratio of PVA over HA from 0.4 to 0.1. Abrasion experiments simulating bone-implant contact illustrate how the coating cohesion and wear resistance increase by increasing the content of PVA relative to HA. Using pullout experiments, we find that these coatings adhere well to the fiber bundles and detach by propagation of a crack inside the coating. These results provide a guide to select coated implants for anchoring artificial ligaments. PMID:25482413

Radiation sensitive indicator based on tetrabromophenol blue dyed poly(vinyl alcohol)

International Nuclear Information System (INIS)

Beshir, W.B.

2013-01-01

Radiation sensitive indicators based on dyed polyvinyl alcohol (PVA) containing acid- sensitive dye (tetrabromophenol blue, TBPB) and chloral hydrate (CCl 3 ·CH·(OH) 2 , 2,2,2-trichloroethane-1,1-diol) have been developed. These plastic film dosimeters undergo color change from blue (the alkaline form of TBPB) to yellow (the acidic form of TBPB), indicating acid formation. The concentration of radiation formed acids in the films containing different concentrations of chloral hydrate was calculated at different doses. These films can be used as dosimeters for food irradiation applications where the maximum of the useful dose ranges are between 1 and 8 kGy depending on chloral hydrate concentration in the film. The films have the advantage of negligible humidity effects on response in the intermediate range of relative humidity from 0 to 70% as good post irradiation stability when stored in the dark at room temperature. The overall combined uncertainty (at 2σ) associated with measurement of response (ΔA mm −1 ) at 623 nm for dose range 1–8 kGy is 4.53%. - Highlights: ► On irradiating TBPB/PVA films the color change from blue to green and yellow. ► The amount of acid formed depends on dose and concentration of chloral hydrate. ► The dose range 1–8 kGy the film can be used for food irradiation applications. ► The response of these films has negligible humidity effects from 0 to 70%. ► The combined uncertainty at 2σ using TBPB/PVA films was found to be 4.53%

Poly(vinyl alcohol) hydrogel coatings with tunable surface exposure of hydroxyapatite.

Science.gov (United States)

Moreau, David; Villain, Arthur; Ku, David N; Corté, Laurent

2014-01-01

Insufficient bone anchoring is a major limitation of artificial substitutes for connective osteoarticular tissues. The use of coatings containing osseoconductive ceramic particles is one of the actively explored strategies to improve osseointegration and strengthen the bone-implant interface for general tissue engineering. Our hypothesis is that hydroxyapatite (HA) particles can be coated robustly on specific assemblies of PVA hydrogel fibers for the potential anchoring of ligament replacements. A simple dip-coating method is described to produce composite coatings made of microscopic hydroxyapatite (HA) particles dispersed in a poly(vinyl alcohol) (PVA) matrix. The materials are compatible with the requirements for implant Good Manufacturing Practices. They are applied to coat bundles of PVA hydrogel fibers used for the development of ligament implants. By means of optical and electronic microscopy, we show that the coating thickness and surface state can be adjusted by varying the composition of the dipping solution. Quantitative analysis based on backscattered electron microscopy show that the exposure of HA at the coating surface can be tuned from 0 to over 55% by decreasing the weight ratio of PVA over HA from 0.4 to 0.1. Abrasion experiments simulating bone-implant contact illustrate how the coating cohesion and wear resistance increase by increasing the content of PVA relative to HA. Using pullout experiments, we find that these coatings adhere well to the fiber bundles and detach by propagation of a crack inside the coating. These results provide a guide to select coated implants for anchoring artificial ligaments.

Elastic properties of thin poly(vinyl alcohol)–cellulose nanocrystal membranes

International Nuclear Information System (INIS)

Pakzad, A; Yassar, R S; Simonsen, J

2012-01-01

In spite of extensive studies on the preparation and characterization of nanocomposite materials, the correlation of their properties at the nanoscale with those in bulk is a relatively unexplored area. This is of great importance, especially for materials with potential biomedical applications, where surface properties are as important in determining their applicability as bulk characteristics. In this study, the nanomechanical characteristics of thin poly(vinyl alcohol) (PVOH)–poly(acrylic acid) (PAA)–cellulose nanocrystal (CNC) membranes were studied using the nanoindentation module in an atomic force microscope (AFM) and the properties were compared with the macro-scale properties obtained by tensile tests. In general, the elastic properties measured by nanoindentation followed the same trend as macro-scale tensile tests except for the PVOH 85-PAA 0-CNC 15 sample. In comparison to the macro-scale elastic properties, the measured elastic moduli with AFM were higher. Macro-scale tensile test results indicated that, in the presence of PAA, incorporation of CNCs up to 20 wt% improved the elastic modulus of PVOH, but when no PAA was added, increasing the CNC content above 10 wt% resulted in their agglomeration and degradation in mechanical properties of PVOH. The discrepancy between macro-scale tensile tests and nanoindentation in the PVOH 85-PAA 0-CNC 15 sample was correlated to the high degree of inhomogeneity of CNC dispersion in the matrix. It was found that the composites reinforced with cellulose nanocrystals had smaller indentation imprints and the pile-up effect increased with the increase of cellulose nanocrystal content. (paper)

The effect of the silver nanoparticles on the dynamics of singlet-singlet energy transfer of luminophores in thin films of polyvinyl alcohol

International Nuclear Information System (INIS)

Bryukhanov, V.V.; Samusev, I.G.; Slezhkin, V.A.; Tsibul'nikova, A.V.

2014-01-01

The effect of ablated silver nanoparticles (ANP) on the dynamics of non-radiative inductance-resonance energy transfer and phosphorescence in the donor-acceptor pair of molecules of eosin and methylene blue (MB) luminophores embedded in thin films of polyvinyl alcohol have been investigated. Increased fluorescence intensity of donor (eosin) and acceptor (MB) molecules, as well as a growth of the dipole-dipole transfer efficiency have been obtained under the resonant excitation of the silver ANP surface plasmons in the absorption band of the donor energy. The luminescence quantum yields and the fluorescence lifetimes have been measured. The energy transfer constants, degree of polarization and fluorescence anisotropy have been determined. (authors)

Effect of polyvinyl alcohol (PVA) on Ag-Cu nanopaste performance

Science.gov (United States)

Noordin, Norasiah Mohammad; Razak, Khairunisak Abd; Cheong, Kuan Yew

2017-07-01

Electronic devices used for extreme high temperature continue to be in demand, for instance in aviation, aerospace and automotive industry. The reliability of these devices strongly depends on electronic packaging. Die attach materials is vital in electronic packaging as it provides an interface in between a die and a substrate, and its quality will determine the performance of the devices. Nanopaste is one of categories classified in the die attach systems. It is a mixture of nano sized metal particles and organic additives (binder, surfactant, solvent). In this study, Ag and Cu nanoparticles was mixed into an organic binder system, polyvinyl alcohol (PVA) serves as binder and ethylene glycol functions as surfactant while deionized water used to dissolve PVA. The mixture was inserted in vacuum oven at 70°C and then proceeds for sintering in horizontal tube furnace with various sintering temperature, a dwell time of 30 min and ramp rate of 5°C/min. The samples were then characterized using field emission scanning electron microscope (FE-SEM) to examine the morphology, X-ray diffraction (XRD) for phase identification, Four Point Probe to measure sheet resistance, and thermogravimetric and differential scanning calorimetry analysis (TGA/DSC) to study the thermal response with respect to temperature. These parameter were studied, the effect of PVA amount (0.10, 0.15, 0.20, 0.30, 0.40, 0.50 g) in Ag-Cu nanopaste formulation was visual inspected, the variation of drying time (20, 30, 40, 60, 80, 100, 120 min) in vacuum oven and sintering temperature (280, 300, 320, 340, 360, 380, 400°C) was recorded. The optimum condition for producing Ag-Cu nanopaste is by using 0.15 g of PVA in the Ag-Cu formulation, 30 min drying time and 340°C sintering temperature.

Preparation and characterization of reactive blends of poly(lactic acid), poly(ethylene-co-vinyl alcohol), and poly(ethylene-co-glycidyl methacrylate)

International Nuclear Information System (INIS)

Warangkhana, Phromma; Rathanawan, Magaraphan; Jana Sadhan, C.

2015-01-01

The ternary blends of poly(lactic acid) (PLA), poly(ethylene-co-vinyl alcohol) (EVOH), and poly(ethylene-co-glycidyl methacrylate) (EGMA) were prepared. The role of EGMA as a compatibilizer was evaluated. The weight ratio of PLA:EVOH was 80:20 and the EGMA loadings were varied from 5-20 phr. The blends were characterized as follows: thermal properties by differential scanning calorimetry, morphology by scanning electron microscopy, and mechanical properties by pendulum impact tester, and universal testing machine. The glass transition temperature of PLA blends did not change much when compared with that of PLA. The blends of PLA/EGMA and EVOH/EGMA showed EGMA dispersed droplets where the latter led to poor impact properties. However, the tensile elongation at break and tensile toughness substantially increased upon addition of EGMA to blends of PLA and EVOH. It was noted in tensile test samples that both PLA and EVOH domains fibrillated significantly to produce toughness

Preparation and characterization of reactive blends of poly(lactic acid), poly(ethylene-co-vinyl alcohol), and poly(ethylene-co-glycidyl methacrylate)

Energy Technology Data Exchange (ETDEWEB)

Warangkhana, Phromma; Rathanawan, Magaraphan, E-mail: rathanawan.k@chula.ac.th [Chulalongkorn University, Petroleum and Petrochemical College - Bangkok (Thailand); Jana Sadhan, C., E-mail: janas@uakron.edu [The University of Akron, Department of Polymer Engineering, Ohio (United States)

2015-05-22

The ternary blends of poly(lactic acid) (PLA), poly(ethylene-co-vinyl alcohol) (EVOH), and poly(ethylene-co-glycidyl methacrylate) (EGMA) were prepared. The role of EGMA as a compatibilizer was evaluated. The weight ratio of PLA:EVOH was 80:20 and the EGMA loadings were varied from 5-20 phr. The blends were characterized as follows: thermal properties by differential scanning calorimetry, morphology by scanning electron microscopy, and mechanical properties by pendulum impact tester, and universal testing machine. The glass transition temperature of PLA blends did not change much when compared with that of PLA. The blends of PLA/EGMA and EVOH/EGMA showed EGMA dispersed droplets where the latter led to poor impact properties. However, the tensile elongation at break and tensile toughness substantially increased upon addition of EGMA to blends of PLA and EVOH. It was noted in tensile test samples that both PLA and EVOH domains fibrillated significantly to produce toughness.

Macroporous poly(vinyl alcohol) microspheres bearing phosphate groups as a new adsorbent for low-density lipoprotein apheresis

Energy Technology Data Exchange (ETDEWEB)

Wang Weichao; Xie Hui; Ou Lailiang; Wang Lianyong; Yu Yaoting; Kong Deling [Key Laboratory of Bioactive Materials, Ministry of Education, College of Life Science, Nankai University, Tianjin 300071 (China); Sun Lisha, E-mail: wly@nankai.edu.c, E-mail: kongdeling@nankai.edu.c [General Hospital, Tianjin Medical University, Tianjin 300052 (China)

2009-12-15

A new low-density lipoprotein (LDL) adsorbent with phosphate groups as the ligand was prepared in this study. Macroporous poly(vinyl acetate-co-triallyl isocyanurate) microspheres were prepared using a free-radical suspension polymerization method. A hydrolysis reaction in sodium hydroxide/methanol changed the materials into poly(vinyl alcohol) (PVA) microspheres. Further reaction with phosphorus oxychloride in anhydrous DMF led to the LDL adsorbent PVA-phosphate microspheres. The preparation conditions such as reaction time, temperature and the amount of phosphorus oxychloride were optimized. The adsorption of plasma lipoproteins was examined by in vitro adsorption assays. The influence of adsorption time, plasma volume and ionic strength on the adsorption capacity was investigated. The circulation adsorption showed that the pathogenic lipoproteins in the plasma such as total cholesterol (TC), LDL and triglyceride (TG) could be removed markedly, in which the removal percentages were 42.9%, 45.0% and 44.74%, respectively. However, the reduction of high-density lipoprotein (HDL) and other normal plasma components was very slight. For in vivo experiment, rabbits were fed with high-cholesterol food to develop a hyperlipidemia model and treated by extracorporeal blood perfusion using the PVA-phosphate columns. Eight hyperlipidemia rabbits were treated with the PVA-phosphate adsorbent, and the removal of TC, LDL and TG was 45.03 +- 6.64%, 48.97 +- 9.92% and 35.42 +- 14.17%, respectively. The sterilization and storage tests showed that the adsorbent was chemically and functionally stable. It could be easily sterilized by a common method and stored for months without loss of adsorption capacity. Therefore, this new PVA-phosphate-based LDL adsorbent may have potential for application in LDL apheresis.

Macroporous poly(vinyl alcohol) microspheres bearing phosphate groups as a new adsorbent for low-density lipoprotein apheresis

International Nuclear Information System (INIS)

Wang Weichao; Xie Hui; Ou Lailiang; Wang Lianyong; Yu Yaoting; Kong Deling; Sun Lisha

2009-01-01

A new low-density lipoprotein (LDL) adsorbent with phosphate groups as the ligand was prepared in this study. Macroporous poly(vinyl acetate-co-triallyl isocyanurate) microspheres were prepared using a free-radical suspension polymerization method. A hydrolysis reaction in sodium hydroxide/methanol changed the materials into poly(vinyl alcohol) (PVA) microspheres. Further reaction with phosphorus oxychloride in anhydrous DMF led to the LDL adsorbent PVA-phosphate microspheres. The preparation conditions such as reaction time, temperature and the amount of phosphorus oxychloride were optimized. The adsorption of plasma lipoproteins was examined by in vitro adsorption assays. The influence of adsorption time, plasma volume and ionic strength on the adsorption capacity was investigated. The circulation adsorption showed that the pathogenic lipoproteins in the plasma such as total cholesterol (TC), LDL and triglyceride (TG) could be removed markedly, in which the removal percentages were 42.9%, 45.0% and 44.74%, respectively. However, the reduction of high-density lipoprotein (HDL) and other normal plasma components was very slight. For in vivo experiment, rabbits were fed with high-cholesterol food to develop a hyperlipidemia model and treated by extracorporeal blood perfusion using the PVA-phosphate columns. Eight hyperlipidemia rabbits were treated with the PVA-phosphate adsorbent, and the removal of TC, LDL and TG was 45.03 ± 6.64%, 48.97 ± 9.92% and 35.42 ± 14.17%, respectively. The sterilization and storage tests showed that the adsorbent was chemically and functionally stable. It could be easily sterilized by a common method and stored for months without loss of adsorption capacity. Therefore, this new PVA-phosphate-based LDL adsorbent may have potential for application in LDL apheresis.

Utilization of Renewable Oxygenates as Gasoline Blending Components

Energy Technology Data Exchange (ETDEWEB)

Yanowitz, J.; Christensen, E.; McCormick, R. L.

2011-08-01

This report reviews the use of higher alcohols and several cellulose-derived oxygenates as blend components in gasoline. Material compatibility issues are expected to be less severe for neat higher alcohols than for fuel-grade ethanol. Very little data exist on how blending higher alcohols or other oxygenates with gasoline affects ASTM Standard D4814 properties. Under the Clean Air Act, fuels used in the United States must be 'substantially similar' to fuels used in certification of cars for emission compliance. Waivers for the addition of higher alcohols at concentrations up to 3.7 wt% oxygen have been granted. Limited emission testing on pre-Tier 1 vehicles and research engines suggests that higher alcohols will reduce emissions of CO and organics, while NOx emissions will stay the same or increase. Most oxygenates can be used as octane improvers for standard gasoline stocks. The properties of 2-methyltetrahydrofuran, dimethylfuran, 2-methylfuran, methyl pentanoate and ethyl pentanoate suggest that they may function well as low-concentration blends with gasoline in standard vehicles and in higher concentrations in flex fuel vehicles.

Surface modification of polyvinyl alcohol/malonic acid nanofibers by gaseous dielectric barrier discharge plasma for glucose oxidase immobilization

Science.gov (United States)

Afshari, Esmail; Mazinani, Saeedeh; Ranaei-Siadat, Seyed-Omid; Ghomi, Hamid

2016-11-01

Polymeric nanofiber prepares a suitable situation for enzyme immobilization for variety of applications. In this research, we have fabricated polyvinyl alcohol (PVA)/malonic acid nanofibers using electrospinning. After fabrication of nanofibers, the effect of air, nitrogen, CO2, and argon DBD (dielectric barrier discharge) plasmas on PVA/malonic acid nanofibers were analysed. Among them, air plasma had the most significant effect on glucose oxidase (GOx) immobilization. Attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectrum analysis and X-ray photoelectron spectroscopy (XPS) results revealed that in case of air plasma modified nanofibers, the carboxyl groups on the surface are increased. The scanning electron microscopy (SEM) images showed that, after GOx immobilization, the modified nanofibers with plasma has retained its nanofiber structure. Finally, we analysed reusability and storage stability of GOx immobilized on plasma modified and unmodified nanofibers. The results were more satisfactory for modified nanofibers with respect to unmodified ones.

Flame-retardant polyvinyl alcohol membrane with high transparency based on a reactive phosphorus-containing compound.

Science.gov (United States)

Peng, Sha; Zhou, Ming; Liu, Feiyan; Zhang, Chang; Liu, Xueqing; Liu, Jiyan; Zou, Liyong; Chen, Jia

2017-08-01

Flame-retardant polyvinyl alcohol (PVA) membranes with high transparency and flexibility were prepared by mixing an aqueous solution of a phosphorus-containing acrylic acid (AOPA) with PVA. The reaction between AOPA and PVA, the transparency, the crystallinity and the flexibility of the membrane were investigated with Fourier transform infrared spectrometry (FTIR), UV-vis light transmittance, X-ray diffraction and tensile tests, respectively. The limited oxygen index (LOI) and vertical flame (UL 94 VTM), microscale combustion calorimetry, thermogravimetric analysis (TGA) and TGA-FTIR were employed to evaluate the flame retardancy as well as to reveal the corresponding mechanisms. Results showed that PVA containing 30 wt% of AOPA can reach the UL 94 VTM V0 rating with an LOI of 27.3% and retain 95% of the original transparency of pure PVA. Adding AOPA reduces crystallinity of PVA, while the flexibility is increased. AOPA depresses the thermal degradation of PVA and promotes char formation during combustion. The proposed decomposition mechanism indicates that AOPA acts mainly in the condensed phase.

Poly(vinyl alcohol) separators improve the coulombic efficiency of activated carbon cathodes in microbial fuel cells

KAUST Repository

Chen, Guang

2013-09-01

High-performance microbial fuel cell (MFC) air cathodes were constructed using a combination of inexpensive materials for the oxygen reduction cathode catalyst and the electrode separator. A poly(vinyl alcohol) (PVA)-based electrode separator enabled high coulombic efficiencies (CEs) in MFCs with activated carbon (AC) cathodes without significantly decreasing power output. MFCs with AC cathodes and PVA separators had CEs (43%-89%) about twice those of AC cathodes lacking a separator (17%-55%) or cathodes made with platinum supported on carbon catalyst (Pt/C) and carbon cloth (CE of 20%-50%). Similar maximum power densities were observed for AC-cathode MFCs with (840 ± 42 mW/m2) or without (860 ± 10 mW/m2) the PVA separator after 18 cycles (36 days). Compared to MFCs with Pt-based cathodes, the cost of the AC-based cathodes with PVA separators was substantially reduced. These results demonstrated that AC-based cathodes with PVA separators are an inexpensive alternative to expensive Pt-based cathodes for construction of larger-scale MFC reactors. © 2013 Elsevier B.V. All rights reserved.

Surface modification of polyamide reverse osmosis membrane with sulfonated polyvinyl alcohol for antifouling

Science.gov (United States)

Zhang, Yang; Wan, Ying; Pan, Guoyuan; Shi, Hongwei; Yan, Hao; Xu, Jian; Guo, Min; Wang, Zhe; Liu, Yiqun

2017-10-01

Sulfonated polyvinyl alcohol (SPVA) was synthesized by esterification reaction of PVA and sulfuric acid, and the structure was characterized by FTIR spectrum. Then a series of TFC membranes modified with cross-linked SPVA layer were fabricated by coating method, with glutaraldehyde as the cross-linker. The resulting TFC membranes were characterized by SEM, AFM, ATR-FTIR, XPS, streaming potential as well as static contact angle. The TFC membranes modified with SPVA exhibit decreased water flux and increased NaCl rejection with SPVA content increasing in the coating aqueous solution. The optimal PA-SPVA-0.5 sample exhibits a NaCl rejection of 99.18%, which is higher than the 98.32% of the virgin PA membrane. More importantly, the PA-SPVA-0.5 membrane shows much more improved fouling resistance to BSA and CTAB than virgin PA membrane and the TFC sample modified with PVA (PA-PVA-0.5). PA-SPVA-0.5 membrane loses about 8% of the initial flux after BSA fouling for 12 h, which is much lower than those of virgin PA and PA-PVA-0.5 membranes (28% and 15%, respectively). Furthermore, the flux recovery of the PA-SPVA-0.5 membrane reaches above 95% after cleaning. Thus, the PA-SPVA-0.5 membrane shows potential applications as antifouling RO membrane for desalination and purification.

Comparison of Chain Conformation of Poly(vinyl alcohol) in Solutions and Melts from Quantum Chemistry Based Molecular Dynamics Simulations

Science.gov (United States)

Jaffe, Richard; Han, Jie; Matsuda, Tsunetoshi; Yoon, Do; Langhoff, Stephen R. (Technical Monitor)

1997-01-01

Confirmations of 2,4-dihydroxypentane (DHP), a model molecule for poly(vinyl alcohol), have been studied by quantum chemistry (QC) calculations and molecular dynamics (MD) simulations. QC calculations at the 6-311G MP2 level show the meso tt conformer to be lowest in energy followed by the racemic tg, due to intramolecular hydrogen bond between the hydroxy groups. The Dreiding force field has been modified to reproduce the QC conformer energies for DHP. MD simulations using this force field have been carried out for DHP molecules in the gas phase, melt, and CHCl3 and water solutions. Extensive intramolecular hydrogen bonding is observed for the gas phase and CHCl3 solution, but not for the melt or aqueous solution, Such a condensed phase effect due to intermolecular interactions results in a drastic change in chain conformations, in agreement with experiments.

Three-Dimensional Printed Poly(vinyl alcohol) Substrate with Controlled On-Demand Degradation for Transient Electronics.

Science.gov (United States)

Yoon, Jinsu; Han, Jungmin; Choi, Bongsik; Lee, Yongwoo; Kim, Yeamin; Park, Jinhee; Lim, Meehyun; Kang, Min-Ho; Kim, Dae Hwan; Kim, Dong Myong; Kim, Sungho; Choi, Sung-Jin

2018-05-25

Electronics that degrade after stable operation for a desired operating time, called transient electronics, are of great interest in many fields, including biomedical implants, secure memory devices, and environmental sensors. Thus, the development of transient materials is critical for the advancement of transient electronics and their applications. However, previous reports have mostly relied on achieving transience in aqueous solutions, where the transience time is largely predetermined based on the materials initially selected at the beginning of the fabrication. Therefore, accurate control of the transience time is difficult, thereby limiting their application. In this work, we demonstrate transient electronics based on a water-soluble poly(vinyl alcohol) (PVA) substrate on which carbon nanotube (CNT)-based field-effect transistors were fabricated. We regulated the structural parameters of the PVA substrate using a three-dimensional (3D) printer to accurately control and program the transience time of the PVA substrate in water. The 3D printing technology can produce complex objects directly, thus enabling the efficient fabrication of a transient substrate with a prescribed and controlled transience time. In addition, the 3D printer was used to develop a facile method for the selective and partial destruction of electronics.

Superselective arterial embolisation with a liquid polyvinyl alcohol copolymer in patients with acute gastrointestinal haemorrhage

Energy Technology Data Exchange (ETDEWEB)

Lenhart, Markus; Schneider, Hans [Sozialstiftung Bamberg, Department of Diagnostic and Interventional Radiology, Bamberg (Germany); Paetzel, Christian [Klinikum Weiden, Department of Radiology, Weiden (Germany); Sackmann, Michael [Sozialstiftung Bamberg, Department of Gastroenterology, Bamberg (Germany); Jung, Ernst Michael; Schreyer, Andreas G.; Feuerbach, Stefan; Zorger, Niels [University of Regensburg, Department of Radiology, Regensburg (Germany)

2010-08-15

To evaluate the results of emergency embolisation in acute arterial bleeding of the gastrointestinal tract with a liquid polyvinyl alcohol copolymer from two centres. We retrospectively analysed 16 cases (15 patients) of acute arterial bleeding of the gastrointestinal tract where emergency embolotherapy was performed by using the copolymer when acute haemorrhage was not treatable with endoscopic techniques alone. Cause of haemorrhage and technical and clinical success were documented. Arterial embolotherapy was successful in all 16 cases. The technical success rate was 100%. The cause of bleeding was pancreatitis in four, graft-versus-host disease (GVHD) of the colon in three, malignancy in three, angiodysplasia in two, ulcer in two and panarteritis no dosa and trauma in one each. There were no procedure-related complications. No bowel necrosis occurred because of embolisation. In 13 cases, the patients were discharged in good condition (81%); the three patients with GVHD died because of the underlying disease. The copolymer seems to have great potential in embolotherapy of acute arterial gastrointestinal bleeding. In our series none of the patients had rebleeding at the site of embolisation and no clinically obvious bowel necrosis occurred. (orig.)

Synthesis, characterization and antibacterial properties of a novel nanocomposite based on polyaniline/polyvinyl alcohol/Ag

Directory of Open Access Journals (Sweden)

Mansour Ghaffari-Moghaddam

2014-11-01

Full Text Available In this study, a novel nanocomposite based on polyaniline/polyvinyl alcohol/Ag (PANI/PVA/Ag has been successfully synthesized. The chemical reduction method was used to produce Ag nanoparticle colloidal solution from Ag+ ions. The polymerization of aniline occurred in situ for the preparation of polyaniline (PANI in the presence of ammonium persulfate. With exposure to Ag nanoparticles on the PANI/PVA composite, a new nanocomposite was obtained. The morphology and particle size of the novel nanocomposite was studied by scanning electron microscopy (SEM, X-ray diffraction (XRD, and Fourier transform infrared (FT-IR analyses. According to XRD analysis, the size of nanoparticles was found to be in the range of 10–17 nm. SEM images showed the favored shape of nanoparticles as triangle which is a benign shape for antibacterial analysis. The antibacterial activity of the obtained nanocomposite was also evaluated against Gram positive bacteria Staphylococcus aureus (Staph. aureus and Gram negative Escherichia coli (E. coli using the paper disk diffusion method. The antibacterial study showed that the PANI/PVA composite did not have a very good antibacterial activity but PANI/PVA/Ag nanocomposites were found to be effective against two bacteria.

Influence of polyvinyl alcohol amount on producing in situ photo-crosslinked thioamide functionalized nanofiber membranes

Directory of Open Access Journals (Sweden)

Zeytuncu Bihter

2015-01-01

Full Text Available Poly(vinyl alcohol/maleic anhydride/acryloyl thioamide monomer (PVA/MA/ATM photo-cured nanofiber membranes and pure PVA nanofiber membranes were produced by electrospinning technique. In situ UV radiation was applied during the electrospinning in order to provide polymerization during the jet flight and promote crosslinking of ATM and MA with PVA. The cross-linking was examined by Fourier-transform infrared spectroscopy (FTIR. The morphology and thermal behavior of electrospun nanofiber were characterized by scanning electron microscope (SEM and thermogravimetric analysis (TGA, respectively. The surface area of nanofiber membranes was measured by Brunauer-Emmert-Teller (BET analysis. Furthermore, water durability test was examined. Water durability test demonstrated that in situ photo-cured PVA/MA/ATM nanofiber membrane had the least average mass loss. The surface areas of PVA/MA/ATM nanofiber membranes were 160-280 m2/g. The surface area and diameter of PVA/MA/ATM nanofibers decreased as the PVA content increased. The diameter of nanofibers was obtained less than 100 nm. The results showed that the water-insoluble nanofiber membranes with better chemical and thermal resistance were obtained. These nanofiber membranes may be a promising candidate for the usage of water treatment.

Mechanism and Characteristics of Humidity Sensing with Polyvinyl Alcohol-Coated Fiber Surface Plasmon Resonance Sensor.

Science.gov (United States)

Shao, Yu; Wang, Ying; Cao, Shaoqing; Huang, Yijian; Zhang, Longfei; Zhang, Feng; Liao, Changrui; Wang, Yiping

2018-06-25

A surface plasmon resonance (SPR) sensor based on a side-polished single mode fiber coated with polyvinyl alcohol (PVA) is demonstrated for relative humidity (RH) sensing. The SPR sensor exhibits a resonant dip in the transmission spectrum in ambient air after PVA film coating, and the resonant wavelength shifts to longer wavelengths as the thickness of the PVA film increases. When RH changes, the resonant dip of the sensor with different film-thicknesses exhibits interesting characteristics for optical spectrum evolution. For sensors with initial wavelengths between 550 nm and 750 nm, the resonant dip shifts to longer wavelengths with increasing RH. The averaged sensitivity increases firstly and then drops, and shows a maximal sensitivity of 1.01 nm/RH%. Once the initial wavelength of the SPR sensor exceeds 850 nm, an inflection point of the resonant wavelength shift can be observed with RH increasing, and the resonant dip shifts to shorter wavelengths for RH values exceeding this point, and sensitivity as high as −4.97 nm/RH% can be obtained in the experiment. The sensor is expected to have potential applications in highly sensitive and cost effective humidity sensing.

Mechanism and Characteristics of Humidity Sensing with Polyvinyl Alcohol-Coated Fiber Surface Plasmon Resonance Sensor

Directory of Open Access Journals (Sweden)

Yu Shao

2018-06-01

Full Text Available A surface plasmon resonance (SPR sensor based on a side-polished single mode fiber coated with polyvinyl alcohol (PVA is demonstrated for relative humidity (RH sensing. The SPR sensor exhibits a resonant dip in the transmission spectrum in ambient air after PVA film coating, and the resonant wavelength shifts to longer wavelengths as the thickness of the PVA film increases. When RH changes, the resonant dip of the sensor with different film-thicknesses exhibits interesting characteristics for optical spectrum evolution. For sensors with initial wavelengths between 550 nm and 750 nm, the resonant dip shifts to longer wavelengths with increasing RH. The averaged sensitivity increases firstly and then drops, and shows a maximal sensitivity of 1.01 nm/RH%. Once the initial wavelength of the SPR sensor exceeds 850 nm, an inflection point of the resonant wavelength shift can be observed with RH increasing, and the resonant dip shifts to shorter wavelengths for RH values exceeding this point, and sensitivity as high as −4.97 nm/RH% can be obtained in the experiment. The sensor is expected to have potential applications in highly sensitive and cost effective humidity sensing.

Superselective arterial embolisation with a liquid polyvinyl alcohol copolymer in patients with acute gastrointestinal haemorrhage

International Nuclear Information System (INIS)

Lenhart, Markus; Schneider, Hans; Paetzel, Christian; Sackmann, Michael; Jung, Ernst Michael; Schreyer, Andreas G.; Feuerbach, Stefan; Zorger, Niels

2010-01-01

To evaluate the results of emergency embolisation in acute arterial bleeding of the gastrointestinal tract with a liquid polyvinyl alcohol copolymer from two centres. We retrospectively analysed 16 cases (15 patients) of acute arterial bleeding of the gastrointestinal tract where emergency embolotherapy was performed by using the copolymer when acute haemorrhage was not treatable with endoscopic techniques alone. Cause of haemorrhage and technical and clinical success were documented. Arterial embolotherapy was successful in all 16 cases. The technical success rate was 100%. The cause of bleeding was pancreatitis in four, graft-versus-host disease (GVHD) of the colon in three, malignancy in three, angiodysplasia in two, ulcer in two and panarteritis no dosa and trauma in one each. There were no procedure-related complications. No bowel necrosis occurred because of embolisation. In 13 cases, the patients were discharged in good condition (81%); the three patients with GVHD died because of the underlying disease. The copolymer seems to have great potential in embolotherapy of acute arterial gastrointestinal bleeding. In our series none of the patients had rebleeding at the site of embolisation and no clinically obvious bowel necrosis occurred. (orig.)

Synthesis and characterization of poly(vinyl alcohol) membranes with quaternary ammonium groups for wound dressing.

Science.gov (United States)

Chen, Kuo-Yu; Lin, Yu-Sheng; Yao, Chun-Hsu; Li, Ming-Hsien; Lin, Jui-Che

2010-01-01

2-[(acryloyloxy)ethyl]Trimethylammonium chloride (AETMAC) was grafted onto poly(vinyl alcohol) (PVA) using ceric ammonium nitrate (CAN) as a redox initiator. A series of graft co-polymer (PVA-g-PAETMAC) membranes with different contents of AETMAC were prepared with a casting method. The incorporation of AETMAC into PVA chains was confirmed by element analysis and Fourier transform infrared spectroscopy. The effects of grafting on the thermal properties, water take, water vapor transmission rate (WVTR), contact angle, antibacterial activity and cytotoxicity of PVA-g-PAETMAC membranes were investigated. The experiment results showed that PVA-g-PAETMAC membrane has a higher equilibrium swelling ratio, surface hydrophilicity and WVTR than pure PVA membrane. Moreover, the higher the content of AETMAC, the higher were equilibrium swelling ratio, surface hydrophilicity and WVTR. In vitro bacterial adhesion study demonstrated a significantly reduced number of Staphylococcus aureus and Escherichia coli on PVA-g-PAETMAC surfaces when compared to PVA surface. In addition, no significant difference in the in vitro cytotoxicity was observed between PVA and PVA-g-PAETMAC membranes. The presence of quaternary ammonium groups did not reduce L929 cell growth. Therefore, the PVA-g-PAETMAC membranes have the potential for wound-dressing application.

Fabrication of multicolor fluorescent polyvinyl alcohol through surface modification with conjugated polymers by oxidative polymerization

Science.gov (United States)

Hai, Thien An Phung; Sugimoto, Ryuichi

2018-06-01

A simple method for the preparation of multicolor polyvinyl alcohol (PVA) by chemical oxidative polymerization is introduced. The PVA surface was successfully modified with conjugated polymers composed of 3-hexylthiophene (3HT) and fluorene (F). The incorporation of the 3HT/F copolymer onto the PVA surface was confirmed by Fourier-transform infrared (FT-IR), ultraviolet-visible (UV-vis), and fluorescence spectroscopies, X-ray diffraction (XRD), as well as thermogravimetric analysis (TGA), contact angle, and field-emission scanning electron microscopy (FE-SEM) coupled with energy dispersive X-ray (EDX) analysis. Different 3HT/F ratios on the PVA surface result in optical properties that include multicolor-emission and absorption behavior. The color of the resultant (3HT/F)-g-PVA shifted from red to blue, and the quantum yield increased with increasing F content. The surface hydrophobicity of the modified PVA increased significantly through grafting with the conjugated polymers, with the water contact angle increasing by 30° compared to pristine PVA. The PVA XRD peaks were less intense following surface modification. Thermogravimetric analyses reveal that the thermal stability of the PVA decreases as a result of grafting with the 3HT/F copolymers.

Fabrication of antibacterial chitosan-PVA blended film using electrospray technique for food packaging applications.

Science.gov (United States)

Liu, Yaowen; Wang, Shuyao; Lan, Wenting

2018-02-01

In this study, blended films from poly(vinyl alcohol) (PVA) containing chitosan (CS) were prepared via a simple solution casting and electrospraying method. The structures of the PVA-CS films were characterized by Fourier-transform infrared spectroscopy. The morphologies of the films were observed by scanning electron microscopy. The thermal properties of the PVA-CS films were examined by thermogravimetry. The effects of CS contents on the mechanical properties, oxygen permeability values, water vapor permeation levels, and antibacterial behaviors against Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus) strains were investigated. Compared to the pure PVA film, the PVA-CS films showed greater elongation at break, lower oxygen permeability, higher water barrier properties, and greater antibacterial activity, especially for the PVA:CS weight ratio of 75:25. The obtained results indicate the PVA-CS film may be a promising material for food packaging applications. Copyright © 2017 Elsevier B.V. All rights reserved.

Biomimetically Reinforced Polyvinyl Alcohol-Based Hybrid Scaffolds for Cartilage Tissue Engineering

Directory of Open Access Journals (Sweden)

Hwan D. Kim

2017-11-01

Full Text Available Articular cartilage has a very limited regeneration capacity. Therefore, injury or degeneration of articular cartilage results in an inferior mechanical stability, load-bearing capacity, and lubrication capability. Here, we developed a biomimetic scaffold consisting of macroporous polyvinyl alcohol (PVA sponges as a platform material for the incorporation of cell-embedded photocrosslinkable poly(ethylene glycol diacrylate (PEGDA, PEGDA-methacrylated chondroitin sulfate (PEGDA-MeCS; PCS, or PEGDA-methacrylated hyaluronic acid (PEGDA-MeHA; PHA within its pores to improve in vitro chondrocyte functions and subsequent in vivo ectopic cartilage tissue formation. Our findings demonstrated that chondrocytes encapsulated in PCS or PHA and loaded into macroporous PVA hybrid scaffolds maintained their physiological phenotypes during in vitro culture, as shown by the upregulation of various chondrogenic genes. Further, the cell-secreted extracellular matrix (ECM improved the mechanical properties of the PVA-PCS and PVA-PHA hybrid scaffolds by 83.30% and 73.76%, respectively, compared to their acellular counterparts. After subcutaneous transplantation in vivo, chondrocytes on both PVA-PCS and PVA-PHA hybrid scaffolds significantly promoted ectopic cartilage tissue formation, which was confirmed by detecting cells positively stained with Safranin-O and for type II collagen. Consequently, the mechanical properties of the hybrid scaffolds were biomimetically reinforced by 80.53% and 210.74%, respectively, compared to their acellular counterparts. By enabling the recapitulation of biomimetically relevant structural and functional properties of articular cartilage and the regulation of in vivo mechanical reinforcement mediated by cell–matrix interactions, this biomimetic material offers an opportunity to control the desired mechanical properties of cell-laden scaffolds for cartilage tissue regeneration.

Submillimeter Diameter Poly(Vinyl Alcohol) Vascular Graft Patency in Rabbit Model

Science.gov (United States)

Cutiongco, Marie F. A.; Kukumberg, Marek; Peneyra, Jonnathan L.; Yeo, Matthew S.; Yao, Jia Y.; Rufaihah, Abdul Jalil; Le Visage, Catherine; Ho, Jackie Pei; Yim, Evelyn K. F.

2016-01-01

Microvascular surgery is becoming a prevalent surgical practice. Replantation, hand reconstruction, orthopedic, and free tissue transfer procedures all rely on microvascular surgery for the repair of venous and arterial defects at the millimeter and submillimeter levels. Often, a vascular graft is required for the procedure as a means to bridge the gap between native arteries. While autologous vessels are desired for their bioactivity and non-thrombogenicity, the tedious harvest process, lack of availability, and caliber or mechanical mismatch contribute to graft failure. Thus, there is a need for an off-the-shelf artificial vascular graft that has low thrombogenic properties and mechanical properties matching those of submillimeter vessels. Poly(vinyl alcohol) hydrogel (PVA) has excellent prospects as a vascular graft due to its bioinertness, low thrombogenicity, high water content, and tunable mechanical properties. Here, we fabricated PVA grafts with submillimeter diameter and mechanical properties that closely approximated those of the rabbit femoral artery. In vitro platelet adhesion and microparticle release assay verified the low thrombogenicity of PVA. A stringent proof-of-concept in vivo test was performed by implanting PVA grafts in rabbit femoral artery with multilevel arterial occlusion. Laser Doppler measurements indicated the improved perfusion of the distal limb after implantation with PVA grafts. Moreover, ultrasound Doppler and angiography verified that the submillimeter diameter PVA vascular grafts remained patent for 2 weeks without the aid of anticoagulant or antithrombotics. Endothelial cells were observed in the luminal surface of one patent PVA graft. The advantageous non-thrombogenic and tunable mechanical properties of PVA that are retained even in the submillimeter diameter dimensions support the application of this biomaterial for vascular replacement in microvascular surgery. PMID:27376059

Effect of annealing temperature on electrical properties of Au/polyvinyl alcohol/n-InP Schottky barrier structure

International Nuclear Information System (INIS)

Reddy, V. Rajagopal; Reddy, M. Siva Pratap; Kumar, A. Ashok; Choi, Chel-Jong

2012-01-01

In the present work, thin film of polyvinyl alcohol (PVA) is fabricated on n-type InP substrate as an interfacial layer for electronic modification of Au/n-InP Schottky contact. The electrical characteristics of Au/PVA/n-InP Schottky diode are determined at annealing temperature in the range of 100–300 °C by current–voltage (I-V) and capacitance–voltage (C-V) methods. The Schottky barrier height and ideality factor (n) values of the as-deposited Au/PVA/n-InP diode are obtained at room temperature as 0.66 eV (I-V), 0.82 eV (C-V) and 1.32, respectively. Upon annealing at 200 °C in nitrogen atmosphere for 1 min, the barrier height value increases to 0.81 eV (I-V), 0.99 eV (C-V) and ideality factor decreases to 1.18. When the contact is annealed at 300 °C, the barrier height value decreases to 0.77 eV (I-V), 0.96 eV (C-V) and ideality factor increases to 1.22. It is observed that the interfacial layer of PVA increases the barrier height by the influence of the space charge region of the Au/n-InP Schottky junction. The discrepancy between Schottky barrier heights calculated from I-V and C-V measurements is also explained. Further, Cheung's functions are used to extract the series resistance of Au/PVA/n-InP Schottky diode. The interface state density as determined by Terman's method is found to be 1.04 × 10 12 and 0.59 × 10 12 cm −2 eV −1 for the as-deposited and 200 °C annealed Au/PVA/n-InP Schottky diodes. Finally, it is seen that the Schottky diode parameters changed with increase in the annealing temperature. - Highlights: ► Electrical properties of Au/polyvinyl alcohol (PVA)/n-InP structure have been studied. ► The Au/PVA/n-InP Schottky structure showed a good rectifying behavior. ► A maximum barrier height is obtained when the contact is annealed at 200 °C. ► Interface state density found to be 0.59 × 10 12 cm −2 eV −1 for 200 °C annealed contact. ► Significant effect of interface state density and series resistance on electrical

Study on the performance of eosin-doped poly(vinyl alcohol)/acrylamide photopolymer films for holographic recording using 488-nm wavelength

Science.gov (United States)

Rajesh, Chelakkal Sukumaran; Sreeroop, Sasidharan Savithrydevi; Pramitha, Vayalamkuzhi; Joseph, Rani; Sreekumar, Krishnapillai; Kartha, Cheranellore Sudha

2011-12-01

This article reports a study done on eosin-doped poly(vinyl alcohol)/acrylamide films for holographic recording using 488 nm Ar+ laser. Films were fabricated using gravity settling method at room temperature and were stored under normal laboratory conditions. Ar+ laser (488 nm) was used for fringe recording. Characterization was done by real time transmittance measurement, optical absorption studies, and diffraction efficiency measurements. Various holographic parameters such as exposure energy, recording power, spatial frequency, etc., were optimized so as to ensure maximum performance. More than 85% diffraction efficiency was obtained at an exposure energy of 50 mJ/cm2 in the optimized film. Efforts were taken to study the environmental stability of this self-developing polymeric material by looking at its shelf life and storage life. Compatibility for recording transmission hologram was also checked.

Bioactive 3D-Shaped Wound Dressings Synthesized from Bacterial Cellulose: Effect on Cell Adhesion of Polyvinyl Alcohol Integrated In Situ

Directory of Open Access Journals (Sweden)

Marlon Osorio

2017-01-01

Full Text Available We investigated wound dressing composites comprising fibrils of bacterial cellulose (BC grown by fermentation in the presence of polyvinyl alcohol (PVA followed by physical crosslinking. The reference biointerface, neat BC, favoured adhesion of fibroblasts owing to size exclusion effects. Furthermore, it resisted migration across the biomaterial. Such effects were minimized in the case of PVA/BC membranes. Therefore, the latter are suggested in cases where cell adhesion is to be avoided, for instance, in the design of interactive wound dressings with facile exudate control. The bioactivity and other properties of the membranes were related to their morphology and structure and considered those of collagen fibres. Bioactive materials were produced by simple 3D templating of BC during growth and proposed for burn and skin ulcer treatment.

Investigation of emissions characteristics of secondary butyl alcohol-gasoline blends in a port fuel injection spark ignition engine

Directory of Open Access Journals (Sweden)

Yusri I.M.

2017-01-01

Full Text Available Exhaust emissions especially from light duty gasoline engine are a major contributor to air pollution due to the large number of vehicles on the road. The purpose of this study is to experimentally analyse the exhaust pollutant emissions of a four-stroke port fuel spark ignition engines operating using secondary butyl alcohol–gasoline blends by percentage volume of 5% (GBu5, 10% (GBu10 and 15% (GBu15 of secondary butyl- alcohol (2-butanol additives in gasoline fuels at 50% of wide throttle open. The exhaust emissions characteristics of the engine using blended fuels was compared to the exhaust emissions of the engine with gasoline fuels (G100 as a reference fuels. Exhaust emissions analysis results show that all of the blended fuels produced lower CO by 8.6%, 11.6% and 24.8% for GBu5, GBu10 and GBu15 respectively from 2500 to 4000 RPM, while for HC, both GBu10 and GBu15 were lower than that G100 fuels at all engine speeds. In general, when the engine was operated using blended fuels, the engine produced lower CO and HC, but higher CO2.

Novel proton exchange membrane based on crosslinked poly(vinyl alcohol) for direct methanol fuel cells

Science.gov (United States)

Liu, Chien-Pan; Dai, Chi-An; Chao, Chi-Yang; Chang, Shoou-Jinn

2014-03-01

In this study, we report the synthesis and the characterization of poly (vinyl alcohol) based proton conducting membranes. In particular, we describe a novel physically and chemically PVA/HFA (poly (vinyl alcohol)/hexafluoroglutaric acid) blending membranes with BASANa (Benzenesulfonic acid sodium salt) and GA (Glutaraldehyde) as binary reaction agents. The key PEM parameters such as ion exchange capacity (IEC), water uptake, proton conductivity, and methanol permeability were controlled by adjusting the chemical composition of the membranes. The IEC value of the membrane is found to be an important parameter in affecting water uptake, conductivity as well as the permeability of the resulting membrane. Plots of the water uptake, conductivity, and methanol permeability vs. IEC of the membranes show a distinct change in the slope of their curves at roughly the same IEC value which suggests a transition of structural changes in the network. The proton conductivities and the methanol permeability of all the membranes are in the range of 10-3-10-2 S cm-1 and 10-8-10-7 cm2 s-1, respectively, depending on its binary crosslinking density, and it shows great selectivity compared with those of Nafion®-117. The membranes display good mechanical properties which suggest a good lifetime usage of the membranes applied in DMFCs.

Polyacrylamide polymers derived from acrylonitrile without intermediate isolation

Energy Technology Data Exchange (ETDEWEB)

Norton, C.J.; Falk, D.O.

1977-04-05

Hydrolyzed and neutralized acrylonitrile is polymerized in solution without isolation to produce a high molecular weight polyacrylamide useful for mobility control in secondary recovery of petroleum. The polyacrylamide optionally may be hydrolyzed, methylolated, and sulfomethylated to further enhance its water-thickening properties. This procedure reduces the cost of making polyacrylamide. (5 claims)

Electrochemical performance of an air-breathing direct methanol fuel cell using poly(vinyl alcohol)/hydroxyapatite composite polymer membrane

Science.gov (United States)

Yang, Chun-Chen; Chiu, Shwu-Jer; Lin, Che-Tseng

A novel composite polymer membrane based on poly(vinyl alcohol)/hydroxyapatite (PVA/HAP) was successfully prepared by a solution casting method. The characteristic properties of the PVA/HAP composite polymer membranes were examined by thermal gravimetric analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), micro-Raman spectroscopy and AC impedance method. An air-breathing DMFC, comprised of an air cathode electrode with MnO 2/BP2000 carbon inks on Ni-foam, an anode electrode with PtRu black on Ti-mesh, and the PVA/HAP composite polymer membrane, was assembled and studied. It was found that this alkaline DMFC showed an improved electrochemical performance at ambient temperature and pressure; the maximum peak power density of an air-breathing DMFC in 8 M KOH + 2 M CH 3OH solution is about 11.48 mW cm -2. From the application point of view, these composite polymer membranes show a high potential for the DMFC applications.

Photochromic and thermal properties of poly(vinyl alcohol)/H6P2W18O62 hybrid membranes

International Nuclear Information System (INIS)

Gong Jian; Li Xiangdan; Shao Changlu; Ding Bin; Lee, Douk-Rae; Kim, Hak-Yong

2003-01-01

Poly(vinyl alcohol) (PVA) films, which contained different content of heteropolyacid (HPA) with Dawson-Wells structure, were prepared. The photochromic behavior was investigated by using ultraviolet-visible (UV-Vis) absorption spectroscopy. The result indicated that the film was reduced photochemically to yield a blue species under UV irradiation, and the color of the film changed to deep blue with increasing irradiation time and HPA content. The photochromic sensibility of different UV wavelength was investigated. In the UV-Vis spectra of the irradiated films, an isobestic point was observed at about 352 nm. The reduction mechanism of the heteropolyanion (W 6+ →W 5+ ) was suggested. The thermal property and the conductivity of the film were also studied. The thermal degradation step and the melting point of the film were influenced by different content of the HPA. Notably, the conductivity of 8.33x10 -6 S cm -1 was observed when the HPA content was 80 wt.%